Home school student visit and introduction to rail transportation and engineering.

Science.gov (United States)

2016-06-22

This project consisted of hosting local Champaign-Urbana, Illinois home school students for a visit to : the Rail Transportation and Engineering Center (RailTEC) at the University of Illinois at Urbana- : Champaign (UIUC). Beyond visiting RailTEC, st...

Optimal Placement Method of RFID Readers in Industrial Rail Transport for Uneven Rail Traflc Volume Management

Science.gov (United States)

Rakhmangulov, Aleksandr; Muravev, Dmitri; Mishkurov, Pavel

2016-11-01

The issue of operative data reception on location and movement of railcars is significant the constantly growing requirements of the provision of timely and safe transportation. The technical solution for efficiency improvement of data collection on rail rolling stock is the implementation of an identification system. Nowadays, there are several such systems, distinguished in working principle. In the authors' opinion, the most promising for rail transportation is the RFID technology, proposing the equipping of the railway tracks by the stationary points of data reading (RFID readers) from the onboard sensors on the railcars. However, regardless of a specific type and manufacturer of these systems, their implementation is affiliated with the significant financing costs for large, industrial, rail transport systems, owning the extensive network of special railway tracks with a large number of stations and loading areas. To reduce the investment costs for creation, the identification system of rolling stock on the special railway tracks of industrial enterprises has developed the method based on the idea of priority installation of the RFID readers on railway hauls, where rail traffic volumes are uneven in structure and power, parameters of which is difficult or impossible to predict on the basis of existing data in an information system. To select the optimal locations of RFID readers, the mathematical model of the staged installation of such readers has developed depending on the non-uniformity value of rail traffic volumes, passing through the specific railway hauls. As a result of that approach, installation of the numerous RFID readers at all station tracks and loading areas of industrial railway stations might be not necessary,which reduces the total cost of the rolling stock identification and the implementation of the method for optimal management of transportation process.

Comparison of Urban and Suburban Rail Transport in Germany and in the Czech Republic

Directory of Open Access Journals (Sweden)

Seidenglanz Daniel

2014-06-01

Full Text Available Rail transport is an environmentally friendly form of passenger transport which can be utilized effectively also in urban and suburban transport systems. The paper describes the urban and suburban rail transport system including comparison of selected Czech (Prague, Brno and Ostrava and German metropolitan regions (Munich, Nuremberg and Dresden. Its aim is to analyze the importance of various factors influencing the differences between the situation in Germany and in the Czech Republic. Therefore, the research question is whether these differences are primarily caused by a different liberalization stage, or whether they are a result of other factors such as available infrastructure, investment level, rail transport services budget, structure and activity of ordering bodies and coordinators or geographical context. The supply of city and suburban rail transport is quite good in Germany and in the Czech Republic, although trains in Munich, Nuremberg and Dresden run more frequently, faster and are better interconnected with car transport. German rail transport sector is at a higher stage of liberalization, and tendering procedures are the preferred selection method for contractor carriers. However, a degree of liberalization of the railway sector is not the key marker indicating a better standard of urban and suburban rail transport in Germany because it is the high standard which is achieved as the consequence of the professional activity of the ordering bodies and train service coordinators in combination with geographical conditions, available financial sources and effective transport infrastructure. On the other hand, the importance of liberalization cannot be totally overlooked as tenders are a tool for the ordering bodies to strongly affect the price and quality of transport services in their area. The supply of better quality and attractive transport to passengers could increase the usage of rail transport in metropolitan regions and could

A REVIEW OF HIGH-SPEED RAIL PLAN IN JAVA ISLAND: A COMPARISON WITH EXISTING MODES OF TRANSPORT

Directory of Open Access Journals (Sweden)

Eko Hartono

2013-05-01

It can be concluded that journey time and fare of the high-speed rail is very competitive to the air transport in Jakarta-Surabaya corridor. The journey time to travel from Jakarta to Surabaya is 4 hours and 19 minutes by high-speed train and 4 hours and 40 minutes by air. Based on the benchmarking analysis, the suitable fare for the high-speed rail should be 70% of the air transport. This study predicted that 61% of air passenger, 18% of conventional rail passenger and 12% of bus passenger will switch to the high-speed rail service in 2020. In total, the high-speed rail will have 24% of market share for the passenger transport and becomes the second largest market share after road transport (52%. The conventional rail and air transport have 14% and 9% of total market share to travel from Jakarta to Surabaya and vice versa. The high-speed rail development reduces carbon emissions caused by transportation systems in Java Island. It has been calculated that there are 2.542 million tonnages of CO2 per annum without introducing high-speed rail, however, the CO2 emissions decrease to 1.694 million tonnages per annum if the high-speed rail is developed in Java Island. Generalized cost of the high-speed rail is higher than road and conventional rail. However, it is lower than air transport. Keywords: Java high-speed rail, HSR Comparison, modal share, journey time

Policy issues of transporting spent nuclear fuel by rail

International Nuclear Information System (INIS)

Spraggins, H.B.

1994-01-01

The topic of this paper is safe and economical transportation of spent nuclear fuel by rail. The cost of safe movement given the liability consequences in the event of a rail accident involving such material is the core issue. Underlying this issue is the ability to access the risk probability of such an accident. The paper delineates how the rail industry and certain governmental agencies perceive and assess such important operational, safety, and economic issues. It also covers benefits and drawbacks of dedicated and regular train movement of such materials

49 CFR 174.82 - General requirements for the handling of placarded rail cars, transport vehicles, freight...

Science.gov (United States)

2010-10-01

... rail cars, transport vehicles, freight containers, and bulk packages. 174.82 Section 174.82... Placarded Rail Cars, Transport Vehicles and Freight Containers § 174.82 General requirements for the handling of placarded rail cars, transport vehicles, freight containers, and bulk packages. (a) Unless...

49 CFR 209.501 - Review of rail transportation safety and security route analysis.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Review of rail transportation safety and security....820 § 209.501 Review of rail transportation safety and security route analysis. (a) Review of route... establish that the route chosen by the carrier poses the least overall safety and security risk, the...

Mock-up tests of rail-mounted vehicle type in-vessel transporter/manipulator

International Nuclear Information System (INIS)

Oka, K.; Kakaudate, S.; Fukatsu, S.

1995-01-01

A rail-mounted vehicle system has been developed for remote maintenance of in-vessel components for fusion experimental reactor. In this system, a rail deploying/storing system is installed at outside of the reactor core and used to deploy a rail transporter and vehicle/manipulator for the in-vessel maintenance. A prototype of the rail deploying/storing system has been fabricated for mockup tests. This paper describes structural design of the prototypical rail deploying/storing system and results of the performance tests such as payload capacity, position control and rail deployment/storage performance

49 CFR 174.84 - Position in train of loaded placarded rail cars, transport vehicles, freight containers or bulk...

Science.gov (United States)

2010-10-01

... CARRIAGE BY RAIL Handling of Placarded Rail Cars, Transport Vehicles and Freight Containers § 174.84 Position in train of loaded placarded rail cars, transport vehicles, freight containers or bulk packagings... 49 Transportation 2 2010-10-01 2010-10-01 false Position in train of loaded placarded rail cars...

The thermal analysis of BR-100: A barge/rail nuclear spent fuel transportation container

International Nuclear Information System (INIS)

Copsey, A.B.

1992-01-01

B ampersand W Fuel Company is designing a spent-fuel container called BR-100 that can be used for either barge or rail transport. This paper presents the thermal design and analysis. Both normal operation and hypothetical accident thermal transient conditions are evaluated. The BR-100 cask has a concrete layer than contains free water. During a hypothetical accident, the free water vaporizes and flows from the cask, removing a significant amount of thermal transient energy. The BR-100 transportation package meets the thermal requirements of 10CFR71. It additionally offers substantial margins to established material temperature limits

On Transport Service Selection in Intermodal Rail/Road Distribution Networks

Directory of Open Access Journals (Sweden)

Christian Bierwirth

2012-11-01

Full Text Available Intermodal rail/road freight transport constitutes an alternative to long-haul road transport for the distribution of large volumes of goods. The paper introduces the intermodal transportation problem for the tactical planning of mode and service selection. In rail mode, shippers either book train capacity on a per-unit basis or charter block trains completely. Road mode is used for short-distance haulage to intermodal terminals and for direct shipments to customers. We analyze the competition of road and intermodal transportation with regard to freight consolidation and service cost on a model basis. The approach is applied to a distribution system of an industrial company serving customers in eastern Europe. The case study investigates the impact of transport cost and consolidation on the optimal modal split.

A proposed regulatory framework for road and rail freight transport in South Africa

Directory of Open Access Journals (Sweden)

Wessel Pienaar

2007-09-01

Full Text Available The increase in the number of freight vehicles on South Africa’s rural road network has received substantial attention. Insinuations persist that long-distance road freight haulage is of a somewhat unsavoury economic nature, and that strict economic re-regulation of the land freight transport is necessary. During the 1970s road transport replaced rail carriage as the dominant form of long-distance freight transport (excluding minerals and ore in South Africa. On long hauls road freight carriers transport certain primary products of an organic nature (such as timber, fish and agricultural produce, some semi-finished goods, many finished goods and most consumer goods. Road freight carriers are continuously gaining market share on long-distance links where rail transport is the more cost efficient mode. The greater value added by road freight carriers in comparison with rail transport through service effectiveness is often more than the cost premium paid for utilising their service rather than making use of rail transport. Throughout history, governments have involved themselves in transport. A diverse range of arguments have been advanced for this involvement in transport, including the following:Control of excessive competition, co-ordination of transport, integration of transport with economic policy, maintenance of safety, security, and order, provision of costly infrastructure, provision of public goods, recovery of the true resource cost of transport inputs, regulation of harmful conduct and externalities, restraint of monopoly power, and social support. A set of nine instruments can be identified that governments apply to influence the performance of the freight transport industry: Legislation, direct supply, fiscal measures, monetary measures, moral appeal and persuasion, policies relating to strategic commodities, procurement policy, provision of information, and research and development. The best prospects for a sound development of

Markets and system developments in rail-guided passenger transport

Energy Technology Data Exchange (ETDEWEB)

Koch, Guenter [DB International GmbH, Karlsruhe (Germany); Grein, Ottmar [DB International GmbH, Frankfurt am Main (Germany)

2013-03-01

The way people are transported is an ever-changing process - and that applies to the railway systems too. If anything, this process of change has sped up in recent years. The authors of this report present an overview of the markets for rail-guided forms of transport and the various systems that exist. (orig.)

2013 International Conference on Electrical and Information Technologies for Rail Transportation

CERN Document Server

Liu, Zhigang; Qin, Yong; Zhao, Minghua; Diao, Lijun

2014-01-01

Proceedings of the 2013 International Conference on Electrical and Information Technologies for Rail Transportation (EITRT2013) collects the latest research in this field, including a wealth of state-of-the-art research theories and applications in intelligent computing, information processing, communication technology, automatic control, etc. The objective of the proceedings is to provide a major interdisciplinary forum for researchers, engineers, academics and industrial professionals to present the most innovative research on and developments in the field of rail transportation electrical and information technologies. Contributing authors from academia, industry and the government also offer inside views of new, interdisciplinary solutions.

Instilling safety culture in the passenger rail transport industry within the South African context

Directory of Open Access Journals (Sweden)

Khulumane (John Maluleke

2013-07-01

Full Text Available South Africa has two major rail operators that constitute the rail transport industry. These are Transnet Freight Rail (TFR, which operates freight and the Passenger Rail Agency of South Africa (PRASA. Although the Railway Safety Regulator (2011:29 reported the year on year declining trend of collisions, the main concern is that the costs incurred for each year’s incidents is escalating. This article is concerned with the declining safety standards of these operators as evidenced by 742 collisions recorded during the 2011/2012 financial year for both operators. The focus is mainly on collisions during the movement of rolling stock within the PRASA environment. The analysis of the occurrences is narrowed down, with the emphasis on the province of Gauteng. In the analysis of the causes of these collisions, the problems that led to the root causes of these collisions is reported. Of critical importance is that every transport operator is faced with the challenges of how to effectively respond to the basic transport needs and requirements of the travelling public. The transport users’ need is to travel between the two geographical points. During the journey between these geographical points, the operator has safety and security requirements and must provide a reliable, accessible and affordable transport system. As the travelling public becomes more affluent, the transport needs become open ended and require much more rational public choices. The rail transport system remains a vital or indispensable business sector of the economy. By investing in new technology, rolling stock and infrastructure, we woud see an increase in innovation, competitiveness, and an elevated standard of living.

Energy study of rail passenger transportation. Volume 2. Description of operating systems. Final report

Energy Technology Data Exchange (ETDEWEB)

Henderson, C.; Ellis, H. T.; Wilhelm, J. P.

1979-08-01

The rail passenger systems of the US are described in terms of selected physical, operating, and economic characteristics, and relates services rendered to energy usage and costs. Rail passenger transportation exists in 4 distinct forms: intercity railroads, suburban railroads, heavy-rail transit, and light-rail transit. Each form varies in technical equipment, design of facilities, operating practices, size of systems. Specific data for the national rail passenger network and the Boston, Chicago, Cleveland, New York, Philadelphia, Pittsburgh, and San Francisco regions and the Washington Metropolitan area transit authority are presented.

The radiological impact of the normal rail transport of radioactive materials in the United Kingdom

International Nuclear Information System (INIS)

Mairs, J.H.

1983-01-01

Recently the NRPB, under contract to the Health and Safety Executive, and in association with the British Railways Board, has assessed the radiological impact of consignments transported on the British Rail system. The work has shown the radiation exposure of British Rail staff and of the public to be low. This paper identifies the types of radioactive materials transported by rail, outlines the methods used to assess the doses to persons exposed and presents the results of these assessments. (author)

49 CFR 174.83 - Switching placarded rail cars, transport vehicles, freight containers, and bulk packagings.

Science.gov (United States)

2010-10-01

... TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS CARRIAGE BY RAIL Handling of Placarded Rail Cars, Transport... force than is necessary to complete the coupling; or (3) Struck by any car moving under its own momentum... its own momentum may be permitted to strike any placarded flatcar or any flatcar carrying a placarded...

Long term energy and emission implications of a global shift to electricity-based public rail transportation system

International Nuclear Information System (INIS)

Chaturvedi, Vaibhav; Kim, Son H.

2015-01-01

With high reliance on light-duty vehicles in the present, the future of global transportation system is also geared towards private modes, which has significant energy and emission implications. Public transportation has been argued as an alternative strategy for meeting the rising transportation demands of the growing world, especially the poor, in a sustainable and energy efficient way. The present study analyzes an important yet under-researched question – what are the long-term energy and emission implications of an electric rail based passenger transportation system for meeting both long and short distance passenter transportation needs? We analyze a suite of electric rail share scenarios with and without climate policy. In the reference scenario, the transportation system will evolve towards dominance of fossil based light-duty vehicles. We find that an electric rail policy is more successful than an economy wide climate policy in reducing transport sector energy demand and emissions. Economy wide emissions however can only be reduced through a broader climate policy, the cost of which can be reduced by hundreds of billions of dollars across the century when implemented in combination with the transport sector focused electric rail policy. Moreover, higher share of electric rail enhances energy security for oil importing nations and reduces vehicular congestion and road infrastructure requirement as well. -- Highlights: •Economy wide carbon price policy will have little impact on transportation emissions. •Focused energy and emission mitigation policies required for transportation sector. •Large global shift towards electric rail based public transport is one possible option. •Transport sector focused policy will have marginal impact on total global emissions. •A combined transport sector and economy wide policy can reduce costs significantly

75 FR 55631 - U. S. Rail Corporation-Construction and Operation Exemption-Brookhaven Rail Terminal

Science.gov (United States)

2010-09-13

... the proposed construction is to enable U. S. Rail to serve the BRT as a common carrier and to deliver... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35141] U. S. Rail Corporation--Construction and Operation Exemption-- Brookhaven Rail Terminal AGENCY: Surface Transportation...

EDRP public local inquiry, UKAEA/BNFL precognition on: the transport of irradiated fuel by rail

International Nuclear Information System (INIS)

Singleton, Leslie

1986-02-01

The experience in handling of irradiated fuel flasks by the British Railways Board is outlined. The steps taken to ensure the effective and safe transport of irradiated fuel and nuclear waste by rail are identified. It is concluded that the proposed rail transport link to the EDRP at Dounreay should prove practicable. (UK)

Participatory evaluation of regional light rail scenarios: A Flemish case on sustainable mobility and land-use

International Nuclear Information System (INIS)

Vermote, Levi; Macharis, Cathy; Hollevoet, Joachim; Putman, Koen

2014-01-01

Highlights: • We propose three light rail scenarios, each covering a specific landscape structure to curtail private vehicle-driven urban sprawl in the Flemish rhombus. • We used the participatory multi-actor multi-criteria analysis (MAMCA) to assess the social, economic and environmental impact of alternative light rail scenarios. • We discuss catalyst measures to comply with the identified drawbacks of the proposed scenarios. - Abstract: Rail transit is generally acknowledged as an alternative transport mode in contributing towards sustainable mobility. In addition to minimising negative externalities, rail transit has sustainable land-use opportunities to integrate transport- and spatial planning. The objective of this paper is to determine the impact of integrative light rail scenarios and their ability to curtail private vehicle driven urban sprawl in the Flemish rhombus. The paper proposes three light rail scenarios: an infrastructural scenario; tramification scenario; and spatial rail scenario, each covering a specific landscape structure to reorganise the dispersed spatial environment in Flanders in the long-term. We used the participatory multi-actor multi-criteria analysis (MAMCA) which incorporates the objectives of all involved stakeholders to assess the impact of the scenarios. The infrastructural alternative scenario gained most support among the involved stakeholders, on the grounds of improved multimodality, enhanced user amenities, reduced implementation costs, moderated greenhouse gas emissions and mitigated infrastructural barrier effects. Despite the merits of the infrastructural scenario in terms of stakeholder objectives, few possibilities are included to elaborate upon sustainable land-use development. In response to the low performance of this assessment criterion, catalyst measures are discussed to support the implementation

Fleet Composition of Rail Tank Cars That Transport Flammable Liquids: 2013-2016

Science.gov (United States)

2017-09-05

Section 7308 of the Fixing America's Surface Transportation Act (FAST Act; P. L. 114-94; December 4, 2015) requires the U.S. Department of Transportation (DOT) to assemble and collect data on rail tank cars transporting Class 3 flammable liquids (box...

A hybrid multi-objective imperialist competitive algorithm and Monte Carlo method for robust safety design of a rail vehicle

Science.gov (United States)

Nejlaoui, Mohamed; Houidi, Ajmi; Affi, Zouhaier; Romdhane, Lotfi

2017-10-01

This paper deals with the robust safety design optimization of a rail vehicle system moving in short radius curved tracks. A combined multi-objective imperialist competitive algorithm and Monte Carlo method is developed and used for the robust multi-objective optimization of the rail vehicle system. This robust optimization of rail vehicle safety considers simultaneously the derailment angle and its standard deviation where the design parameters uncertainties are considered. The obtained results showed that the robust design reduces significantly the sensitivity of the rail vehicle safety to the design parameters uncertainties compared to the determinist one and to the literature results.

First ordinance amending the Ordinance on Rail Transport of Dangerous Goods (1. Amendment Ordinance Rail Transport of Dangerous Goods). As of June 22, 1983

International Nuclear Information System (INIS)

1983-01-01

This Amendment which came into force on September 1, 1983 brings about modifications of many items of the original Ordinance on Rail Transport of Dangerous Goods and its supplement, as of August 29, 1979. (HSCH) [de

Risk of transporting plutonium dioxide and liquid plutonium nitrate by truck and rail

International Nuclear Information System (INIS)

Williams, L.D.; Hall, R.J.

1976-07-01

Results are summarized of the risk assessments of shipping PuO 2 powder and liquid Pu nitrate by truck and rail in the U.S. In the analysis method used, the system is described, potential release sequences are identified and evaluated (fault tree used), and the system risk is assessed. It is concluded that: there is little difference in risk in shipping PuO 2 by rail and by truck; there also is little change in risk in shipping PuO 2 by rail and by truck; there also is little change in risk for liquid shipment; the vermiculite loss is somewhat less important in rail shipment; and the response of the L-10 container to crush is more important in rail transport

Analyzing the United States Department of Transportation's Implementation Strategy for High Speed Rail: Three Case Studies

Science.gov (United States)

Robinson, Ryan

High-speed rail (HSR) has become a major contributor to the transportation sector with a strong push by the Obama Administration and the Department of Transportation to implement high-speed rail in the United States. High-speed rail is a costly transportation alternative that has the potential displace some car and airport travel while increase energy security and environmental sustainability. This thesis will examine the United States high-speed rail implementation strategy by comparing it to the implementation strategies of France, Japan, and Germany in a multiple case study under four main criteria of success: economic profitability, reliability, safety, and ridership. Analysis will conclude with lessons to be taken away from the case studies and applied to the United States strategy. It is important to understand that this project has not been established to create a comprehensive implementation plan for high-speed rail in the United States; rather, this project is intended to observe the depth and quality of the current United States implementation strategy and make additional recommendations by comparing it with France, Japan, and Germany.

Effect of truck and rail economic deregulation on radioactive material transportation

International Nuclear Information System (INIS)

Allen, G.C. Jr.

1984-01-01

An evaluation of the effect of truck and rail economic deregulation on radioactive material transportation is presented in this document. The evaluation is based on expected market performance that would be consistent with fundamental economic theories. The issues of transport safety, commodity discrimination and rates are addressed. Relative to transport safety, deregulation should not have any significant impact. While deregulation should not change commodity acceptance and may lower rates for motor carriage, it may allow increased discrimination by rail carriers in addition to raising rates. Consequently, it is likely that the radioactive material transportation industry will continue to place greater reliance on the competitive motor carrier industry. Positive steps that shippers can take are to maintain credible options to ship by alternate modes, to address issues that result in the perceived need for special risk premiums, and to reduce the cost of handling truck shipments by improvements in technology or procedures. 28 references, 3 figures, 6 tables

Study on transfer optimization of urban rail transit and conventional public transport

Science.gov (United States)

Wang, Jie; Sun, Quan Xin; Mao, Bao Hua

2018-04-01

This paper mainly studies the time optimization of feeder connection between rail transit and conventional bus in a shopping center. In order to achieve the goal of connecting rail transportation effectively and optimizing the convergence between the two transportations, the things had to be done are optimizing the departure intervals, shorting the passenger transfer time and improving the service level of public transit. Based on the goal that has the minimum of total waiting time of passengers and the number of start of classes, establish the optimizing model of bus connecting of departure time. This model has some constrains such as transfer time, load factor, and the convergence of public transportation grid spacing. It solves the problems by using genetic algorithms.

Reported Design Processes for Accessibility in Rail Transport

DEFF Research Database (Denmark)

Herriott, Richard; Cook, Sharon

2014-01-01

requirements with the aim of maximising accessibility in products and services. A review of ID literature has mainly developed in the arena of product design and design for assistive technology. Accessibility is a fundamental requirement in public transport (PT) yet there exists little research on design...... for accessibility or ID in this area. How is accessibility and the needs of users accounted for in rail transport design? This paper analyses interviews with rolling stock producers, operators and design consultancies. These conducted to determine if ID design methods are used explicitly and the extent to which...

New magnetic rails with double-layer Halbach structure by employing NdFeB and ferrite magnets for HTS maglev

Science.gov (United States)

Sun, Ruixue; Zheng, Jun; Zheng, Botian; Qian, Nan; Li, Jipeng; Deng, Zigang

2018-01-01

In the high temperature superconducting (HTS) maglev system, the magnetic rail as an essential infrastructure is needed all along the route to carry passengers and goods to the destinations. Thus, large amount of rare earth magnetic materials are required in the magnetic rail construction. In order to decrease the dependence of magnetic rails on rare earth elements, the ferrite magnet is employed to replace part of the NdFeB magnets containing rare earth elements. Consequently, a new type rail with double-layer Halbach structure is presented, which is consisted of NdFeB and ferrite magnets. In this paper, we designed and fabricated the proposed rail, and further measured its magnetic flux density distribution and electromagnetic force interacting with HTS bulks. Experimental results indicate that, this new type rail, in double-layer Halbach structure, can achieve an equivalent distribution of magnetic flux density and levitation performance as the pure NdFeB Halbach rail, while a 10% reduction in NdFeB magnet consumption can be realized at the same time. In addition this work explores another magnetic material selection for HTS maglev applications. The dependence on rare earth element and the cost of magnetic rails can be further reduced, as the coercive force of ferrite magnets improved.

Regional atmospheric budgets of reduced nitrogen over the British isles assessed using a multi-layer atmospheric transport model

NARCIS (Netherlands)

Fournier, N.; Tang, Y.S.; Dragosits, U.; Kluizenaar, Y.de; Sutton, M.A.

2005-01-01

Atmospheric budgets of reduced nitrogen for the major political regions of the British Isles are investigated with a multi-layer atmospheric transport model. The model is validated against measurements of NH3 concentration and is developed to provide atmospheric budgets for defined subdomains of the

Optimization of wheel-rail interface friction using top-of-rail friction modifiers: State of the art

Science.gov (United States)

Khan, M. Roshan; Dasaka, Satyanarayana Murty

2018-05-01

High Speed Railways and Dedicated Freight Corridors are the need of the day for fast and efficient transportation of the ever growing population and freight across long distances of travel. With the increase in speeds and axle loads carried by these trains, wearing out of rails and train wheel sections are a common issue, which is due to the increase in friction at the wheel-rail interfaces. For the cases where the wheel-rail interface friction is less than optimum, as in case of high speed trains with very low axle loads, wheel-slips are imminent and loss of traction occurs when the trains accelerate rapidly or brake all of a sudden. These vast variety of traction problems around the wheel-rail interface friction need to be mitigated carefully, so that the contact interface friction neither ascents too high to cause material wear and need for added locomotive power, nor be on the lower side to cause wheel-slips and loss of traction at high speeds. Top-of-rail friction modifiers are engineered surface coatings applied on top of rails, to maintain an optimum frictional contact between the train wheels and the rails. Extensive research works in the area of wheel-rail tribology have revealed that the optimum frictional coefficients at wheel-rail interfaces lie at a value of around 0.35. Application of top-of-rail (TOR) friction modifiers on rail surfaces add an extra layer of material coating on top of the rails, with a surface frictional coefficient of the desired range. This study reviews the common types of rail friction modifiers, the methods for their application, issues related with the application of friction modifiers, and a guideline on selection of the right class of coating material based on site specific requirements of the railway networks.

The Homogeneity Research of Urban Rail Transit Network Performance

Directory of Open Access Journals (Sweden)

Wang Fu-jian

2016-01-01

Full Text Available Urban Rail Transit is an important part of the public transit, it is necessary to carry out the corresponding network function analysis. Previous studies mainly about network performance analysis of a single city rail transit, lacking of horizontal comparison between the multi-city, it is difficult to find inner unity of different Urban Rail Transit network functions. Taking into account the Urban Rail Transit network is a typical complex networks, so this paper proposes the application of complex network theory to research the homogeneity of Urban Rail Transit network performance. This paper selects rail networks of Beijing, Shanghai, Guangzhou as calculation case, gave them a complex network mapping through the L, P Space method and had a static topological analysis using complex network theory, Network characteristics in three cities were calculated and analyzed form node degree distribution and node connection preference. Finally, this paper studied the network efficiency changes of Urban Rail Transit system under different attack mode. The results showed that, although rail transport network size, model construction and construction planning of the three cities are different, but their network performance in many aspects showed high homogeneity.

Thickness dependence of the levitation performance of double-layer high-temperature superconductor bulks above a magnetic rail

International Nuclear Information System (INIS)

Sun, R.X.; Zheng, J.; Liao, X.L.; Che, T.; Gou, Y.F.; He, D.B.; Deng, Z.G.

2014-01-01

Highlights: • Thickness optimization of double-layer bulk HTSC arrangement is studied. • The new bulk HTSC arrangement makes better use of the flux distribution of the magnetic rails. • Levitation performance can be enhanced with the optimization. • The optimization can meet large levitation force requirements for HTS Maglev system. - Abstract: A double-layer high-temperature superconductor (HTSC) arrangement was proposed and proved to be able to bring improvements to both levitation force and guidance force compared with present single-layer HTSC arrangement. To fully exploit the applied magnetic field by a magnetic rail, the thickness dependence of a double-layer HTSC arrangement on the levitation performance was further investigated in the paper. In this study, the lower-layer bulk was polished step by step to different thicknesses, and the upper-layer bulk with constant thickness was directly superimposed on the lower-layer one. The levitation force and the force relaxation of the double-layer HTSC arrangement were measured above a Halbach magnetic rail. Experimental result shows that a bigger levitation force and a less levitation force decay could be achieved by optimizing the thickness of the lower-layer bulk HTSC. This thickness optimization method could be applied together with former reported double-layer HTSC arrangement method with aligned growth sector boundaries pattern. This series of study on the optimized combination method do bring a significant improvement on the levitation performance of present HTS maglev systems

Thickness dependence of the levitation performance of double-layer high-temperature superconductor bulks above a magnetic rail

Energy Technology Data Exchange (ETDEWEB)

Sun, R.X.; Zheng, J.; Liao, X.L.; Che, T.; Gou, Y.F.; He, D.B.; Deng, Z.G., E-mail: zgdeng@gmail.com

2014-10-15

Highlights: • Thickness optimization of double-layer bulk HTSC arrangement is studied. • The new bulk HTSC arrangement makes better use of the flux distribution of the magnetic rails. • Levitation performance can be enhanced with the optimization. • The optimization can meet large levitation force requirements for HTS Maglev system. - Abstract: A double-layer high-temperature superconductor (HTSC) arrangement was proposed and proved to be able to bring improvements to both levitation force and guidance force compared with present single-layer HTSC arrangement. To fully exploit the applied magnetic field by a magnetic rail, the thickness dependence of a double-layer HTSC arrangement on the levitation performance was further investigated in the paper. In this study, the lower-layer bulk was polished step by step to different thicknesses, and the upper-layer bulk with constant thickness was directly superimposed on the lower-layer one. The levitation force and the force relaxation of the double-layer HTSC arrangement were measured above a Halbach magnetic rail. Experimental result shows that a bigger levitation force and a less levitation force decay could be achieved by optimizing the thickness of the lower-layer bulk HTSC. This thickness optimization method could be applied together with former reported double-layer HTSC arrangement method with aligned growth sector boundaries pattern. This series of study on the optimized combination method do bring a significant improvement on the levitation performance of present HTS maglev systems.

49 CFR 214.523 - Hi-rail vehicles.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Hi-rail vehicles. 214.523 Section 214.523..., DEPARTMENT OF TRANSPORTATION RAILROAD WORKPLACE SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.523 Hi-rail vehicles. (a) The hi-rail gear of all hi-rail vehicles shall be inspected for...

An Investigation into the Non-bulk Rail Freight Transport in Australia

Directory of Open Access Journals (Sweden)

Hadi Ghaderi

2015-03-01

Full Text Available In the last decade freight transport has gained further momentum in Australia, partly through significant demand growth at both domestic and international levels and partly as the result of Australia's long term need for infrastructure decision making. Amongst the freight task, non-bulk freight is the fastest growing freight task in Australia and is forecast to grow much faster than the rate of population growth and the average national GDP growth. However, rail's share in the non-bulk market has declined significantly in the last four decades. This study therefore provides an insight into the efficiency and operational management issues facing by the Australian non-bulk rail sector by focusing on three areas; the level of track compatibility and the relevant operational issues, the demographics of non-bulk freight in Australia and the current status of intermodal terminals in relation to rail connectivity and location. As the result, a more detailed understanding of the current shortages in the Australian non-bulk rail freight sector is achieved and managerial implications are provided.

Rail security : some actions taken to enhance passenger and freight rail security, but significant challenges remain : testimony before the Committee on Commerce, Science, and Transportation, U.S. Senate

Science.gov (United States)

2004-03-23

Passenger and freight rail services are important links in the nation's transportation system. Terrorist attacks on passenger and/or freight rail services have the potential to cause widespread injury, loss of life, and economic disruption. The recen...

Light rail project in Copenhagen

DEFF Research Database (Denmark)

Andersen, Jonas Lohmann Elkjær; Landex, Alex; Nielsen, Otto Anker

2006-01-01

The need for high class public transport service of the increasing travel across the radial urban structure of the greater Copenhagen region was examined through planning of a light rail. The exact corridor (defined as the Ring 2½ corridor) and alignment of the light rail were documented and the ......The need for high class public transport service of the increasing travel across the radial urban structure of the greater Copenhagen region was examined through planning of a light rail. The exact corridor (defined as the Ring 2½ corridor) and alignment of the light rail were documented...... light rail projects...

49 CFR 210.9 - Movement of a noise defective locomotive, rail car, or consist of a locomotive and rail cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Movement of a noise defective locomotive, rail car, or consist of a locomotive and rail cars. 210.9 Section 210.9 Transportation Other Regulations... locomotive, rail car, or consist of a locomotive and rail cars. A locomotive, rail car, or consist of a...

An improved AE detection method of rail defect based on multi-level ANC with VSS-LMS

Science.gov (United States)

Zhang, Xin; Cui, Yiming; Wang, Yan; Sun, Mingjian; Hu, Hengshan

2018-01-01

In order to ensure the safety and reliability of railway system, Acoustic Emission (AE) method is employed to investigate rail defect detection. However, little attention has been paid to the defect detection at high speed, especially for noise interference suppression. Based on AE technology, this paper presents an improved rail defect detection method by multi-level ANC with VSS-LMS. Multi-level noise cancellation based on SANC and ANC is utilized to eliminate complex noises at high speed, and tongue-shaped curve with index adjustment factor is proposed to enhance the performance of variable step-size algorithm. Defect signals and reference signals are acquired by the rail-wheel test rig. The features of noise signals and defect signals are analyzed for effective detection. The effectiveness of the proposed method is demonstrated by comparing with the previous study, and different filter lengths are investigated to obtain a better noise suppression performance. Meanwhile, the detection ability of the proposed method is verified at the top speed of the test rig. The results clearly illustrate that the proposed method is effective in detecting rail defects at high speed, especially for noise interference suppression.

Integration of geospatial multi-mode transportation Systems in Kuala Lumpur

Science.gov (United States)

Ismail, M. A.; Said, M. N.

2014-06-01

Public transportation serves people with mobility and accessibility to workplaces, health facilities, community resources, and recreational areas across the country. Development in the application of Geographical Information Systems (GIS) to transportation problems represents one of the most important areas of GIS-technology today. To show the importance of GIS network analysis, this paper highlights the determination of the optimal path between two or more destinations based on multi-mode concepts. The abstract connector is introduced in this research as an approach to integrate urban public transportation in Kuala Lumpur, Malaysia including facilities such as Light Rapid Transit (LRT), Keretapi Tanah Melayu (KTM) Komuter, Express Rail Link (ERL), KL Monorail, road driving as well as pedestrian modes into a single intelligent data model. To assist such analysis, ArcGIS's Network Analyst functions are used whereby the final output includes the total distance, total travelled time, directional maps produced to find the quickest, shortest paths, and closest facilities based on either time or distance impedance for multi-mode route analysis.

Integration of geospatial multi-mode transportation Systems in Kuala Lumpur

International Nuclear Information System (INIS)

Ismail, M A; Said, M N

2014-01-01

Public transportation serves people with mobility and accessibility to workplaces, health facilities, community resources, and recreational areas across the country. Development in the application of Geographical Information Systems (GIS) to transportation problems represents one of the most important areas of GIS-technology today. To show the importance of GIS network analysis, this paper highlights the determination of the optimal path between two or more destinations based on multi-mode concepts. The abstract connector is introduced in this research as an approach to integrate urban public transportation in Kuala Lumpur, Malaysia including facilities such as Light Rapid Transit (LRT), Keretapi Tanah Melayu (KTM) Komuter, Express Rail Link (ERL), KL Monorail, road driving as well as pedestrian modes into a single intelligent data model. To assist such analysis, ArcGIS's Network Analyst functions are used whereby the final output includes the total distance, total travelled time, directional maps produced to find the quickest, shortest paths, and closest facilities based on either time or distance impedance for multi-mode route analysis

THE BAINITIC STEELS FOR RAILS APPLICATIONS

Directory of Open Access Journals (Sweden)

Ivo Hlavatý

2009-10-01

Full Text Available Actual trends of worldwide railway transport development are characterized by increasing speed and growth of railway’s axels load. Increasing load together with transverse, longitudinal wheel displacement and braking on the rails results into heavy surface tension. One of many applications for bainitic steel is in railway transport for highly strength and wear resistant rails. Rail steel must be designed to be able to resist plastic deformation, wear, rolling contact fatigue, bending stress and thermal stress during rail welding process and rails resurfacing.

77 FR 19680 - Extension of Agency Information Collection Activity Under OMB Review: Rail Transportation Security

Science.gov (United States)

2012-04-02

... DEPARTMENT OF HOMELAND SECURITY Transportation Security Administration [Docket No. TSA-2006-26514] Extension of Agency Information Collection Activity Under OMB Review: Rail Transportation Security AGENCY: Transportation Security Administration, DHS. ACTION: 30-day Notice. SUMMARY: This notice announces that the...

Modelling of contact problems involved in ensuring the safety of rail transport

Directory of Open Access Journals (Sweden)

Edward Rydygier

2013-12-01

Full Text Available Background: Mathematical modelling aids diagnostics the track and rolling stock, as it often for technical reasons it is not possible to obtain a complete set of measurement data required to diagnose the rail and wheel deformation caused by the impact of a rail vehicle on the track. The important issue in a railway diagnostics is to study the effects of contact wheel and rail. Diagnostics investigations of track and rolling stock have a fundamental role in ensuring the safety of transport of passengers and goods. The aim of the study presented in the paper was to develop simulation methods of mathematical modelling of the wheel-rail system useful in the diagnostics of the track and a railway vehicle. Methods: In the paper two ways of modelling were presented and discussed. One of these ways is the method which consists in reducing the contact issue to field issue and solving the identification of the field source in 2-D system. Also presented a different method designed on the basis of the methods using one period energy concept. This method is adapted for modelling the dynamics of the contact wheel-rail for the normal force. It has been shown that the developed modelling methods to effectively support the study on the effects of mechanical and thermal of contact wheel-rail and contribute to the safety of operations.  Results and conclusions:  In the case of field sources identifications two specific issues were examined: the issue of rail torsion and the identification of heat sources in the rail due to exposure the rolling contact wheel-rail. In the case of the method using one period energy concept it was demonstrated the usefulness of this method to the study of energy processes in the contact wheel-rail under the normal periodic force. The future direction of research is to establish cooperation with research teams entrusted with the diagnostic measurements of track and rolling stock.  

Rail-Cask Tests: Normal-Conditionsof- Transport Tests of Surrogate PWR Fuel Assemblies in an ENSA ENUN 32P Cask.

Energy Technology Data Exchange (ETDEWEB)

McConnell, Paul E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ross, Steven [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Grey, Carissa Ann [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Uncapher, William Leonard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Arviso, Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Garmendia, Rafael [Equipos Nucleares Sociedad Anonima, Madrid (Spain); Fernandez Perez, Ismael [Equipos Nucleares Sociedad Anonima, Madrid (Spain); Palacio, Alejandro [Equipos Nucleares Sociedad Anonima, Madrid (Spain); Calleja, Guillermo [Equipos Nucleares Sociedad Anonima, Madrid (Spain); Garrido, David [COORDINADORA, Madrid (Spain); Rodriguez Casas, Ana [COORDINADORA, Madrid (Spain); Gonzalez Garcia, Luis [COORDINADORA, Madrid (Spain); Chilton, Lyman Wes [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ammerman, Douglas J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Walz, Jacob [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gershon, Sabina [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Saltzstein, Sylvia J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sorenson, Ken [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Klymyshyn, Nicholas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hanson, Brady [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pena, Ruben [Transportation Technology Center, Inc., Pueblo, CO (United States); Walker, Russell [Transportation Technology Center, Inc., Pueblo, CO (United States)

2018-01-01

This report describes tests conducted using a full-size rail cask, the ENSA ENUN 32P, involving handling of the cask and transport of the cask via truck, ships, and rail. The purpose of the tests was to measure strains and accelerations on surrogate pressurized water reactor fuel rods when the fuel assemblies were subjected to Normal Conditions of Transport within the rail cask. In addition, accelerations were measured on the transport platform, the cask cradle, the cask, and the basket within the cask holding the assemblies. These tests were an international collaboration that included Equipos Nucleares S.A., Sandia National Laboratories, Pacific Northwest National Laboratory, Coordinadora Internacional de Cargas S.A., the Transportation Technology Center, Inc., the Korea Radioactive Waste Agency, and the Korea Atomic Energy Research Institute. All test results in this report are PRELIMINARY – complete analyses of test data will be completed and reported in FY18. However, preliminarily: The strains were exceedingly low on the surrogate fuel rods during the rail-cask tests for all the transport and handling modes. The test results provide a compelling technical basis for the safe transport of spent fuel.

Wireless Communications in Smart Rail Transportation Systems

Directory of Open Access Journals (Sweden)

César Briso-Rodríguez

2017-01-01

Full Text Available Railway, subway, airplane, and other transportation systems have drawn an increasing interest on the use of wireless communications for critical and noncritical services to improve performance, reliability, and passengers experience. Smart transportation systems require the use of critical communications for operation and control, and wideband services can be provided using noncritical communications. High speed train (HST is one of the best test cases for the analysis of communication links and specification of the general requirements for train control and supervision, passenger communications, and onboard and infrastructure wireless sensors. In this paper, we analyze in detail critical and noncritical networks mainly using the HST as a test case. First, the different types of links for smart rail transportation are described, specifying the main requirements of the transportation systems, communications, and their applications for different services. Then, we propose a network architecture and requirements of the communication technologies for critical and noncritical data. Finally, an analysis is made for the future technologies, including the fifth-generation (5G communications, millimeter wave (mmWave, terahertz (THz, and satellites for critical and high-capacity communications in transportation.

76 FR 80448 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2011-12-23

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. EP 290 (Sub-No. 5) (2012-1)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the first quarter 2012 rail cost adjustment factor (RCAF...

78 FR 71724 - Rail Depreciation Studies

Science.gov (United States)

2013-11-29

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board Rail Depreciation Studies AGENCY: Surface Transportation Board, DOT. ACTION: Notice of OMB Approval of Information Collection. SUMMARY... collection, Rail Depreciation Studies. See 78 FR 18676 (Mar. 27, 2013). This collection, codified at 49 CFR...

Modelling the resilience of rail passenger transport networks affected by large-scale disruptive events : the case of HSR (high speed rail)

NARCIS (Netherlands)

Janic, M.

2018-01-01

This paper deals with modelling the dynamic resilience of rail passenger transport networks affected by large-scale disruptive events whose impacts deteriorate the networks’ planned infrastructural, operational, economic, and social-economic performances represented by the selected indicators.

Scheduling of inspectors for ticket spot checking in urban rail transportation

DEFF Research Database (Denmark)

Thorlacius, Per; Clausen, Jens

2010-01-01

A central issue for operators of passenger transportation in urban rail is balancing the income from tickets against the cost of the operation. The main part of the income except for governmental subsides comes from sales of tickets. There are various ways to ensure that all passengers carry valid...

Design considerations for energy efficient, resilient, multi-layer networks

DEFF Research Database (Denmark)

Fagertun, Anna Manolova; Hansen, Line Pyndt; Ruepp, Sarah Renée

2016-01-01

measures. In this complex problem, considerations such as client traffic granularity, applied grooming policies and multi-layer resiliency add even more complexity. A commercially available network planning tool is used to investigate the interplay between different methods for resilient capacity planning......This work investigates different network design considerations with respect to energy-efficiency, under green-field resilient multi-layer network deployment. The problem of energy efficient, reliable multi-layer network design is known to result in different trade-offs between key performance....... Switching off low-utilized transport links has been investigated via a pro-active re-routing applied during the network planning. Our analysis shows that design factors such as the applied survivability strategy and the applied planning method have higher impact on the key performance indicators compared...

78 FR 36017 - MCM Rail Services LLC, d/b/a Baltimore Industrial Railroad-Operation Exemption-Hilco SP Rail, LLC

Science.gov (United States)

2013-06-14

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35725] MCM Rail Services LLC, d/b/a Baltimore Industrial Railroad-- Operation Exemption--Hilco SP Rail, LLC MCM Rail Services LLC, d/b/a Baltimore Industrial Railroad (MCM), a noncarrier, has filed a verified notice of exemption...

Computation of wheel-rail contact force for non-mapping wheel-rail profile of Translohr tram

Science.gov (United States)

Ji, Yuanjin; Ren, Lihui; Zhou, Jinsong

2017-09-01

Translohr tram has steel wheels, in V-like arrangements, as guide wheels. These operate over the guide rails in inverted-V arrangements. However, the horizontal and vertical coordinates of the guide wheels and guide rails are not always mapped one-to-one. In this study, a simplified elastic method is proposed in order to calculate the contact points between the wheels and the rails. By transforming the coordinates, the non-mapping geometric relationship between wheel and rail is converted into a mapping relationship. Considering the Translohr tram's multi-point contact between the guide wheel and the guide rail, the elastic-contact hypothesis take into account the existence of contact patches between the bodies, and the location of the contact points is calculated using a simplified elastic method. In order to speed up the calculation, a multi-dimensional contact table is generated, enabling the use of simulation for Translohr tram running on curvatures with different radii.

Simulation and evaluation of urban rail transit network based on multi-agent approach

Directory of Open Access Journals (Sweden)

Xiangming Yao

2013-03-01

Full Text Available Purpose: Urban rail transit is a complex and dynamic system, which is difficult to be described in a global mathematical model for its scale and interaction. In order to analyze the spatial and temporal characteristics of passenger flow distribution and evaluate the effectiveness of transportation strategies, a new and comprehensive method depicted such dynamic system should be given. This study therefore aims at using simulation approach to solve this problem for subway network. Design/methodology/approach: In this thesis a simulation model based on multi-agent approach has been proposed, which is a well suited method to design complex systems. The model includes the specificities of passengers’ travelling behaviors and takes into account of interactions between travelers and trains. Findings: Research limitations/implications: We developed an urban rail transit simulation tool for verification of the validity and accuracy of this model, using real passenger flow data of Beijing subway network to take a case study, results show that our simulation tool can be used to analyze the characteristic of passenger flow distribution and evaluate operation strategies well. Practical implications: The main implications of this work are to provide decision support for traffic management, making train operation plan and dispatching measures in emergency. Originality/value: A new and comprehensive method to analyze and evaluate subway network is presented, accuracy and computational efficiency of the model has been confirmed and meet with the actual needs for large-scale network.

Sub-Saharan Africa’s rail freight transport system: Potential impact of densification on cost

Directory of Open Access Journals (Sweden)

Anneke de Bod

2010-11-01

Full Text Available The main response to sub-Saharan Africa’s (SSA challenges has been foreign aid. Yet, despite the large amounts received, the challenges remain. There is an opportunity to consider a different model with less focus on aid and more on investment. In the transport sector specifically, investment decisions should be informed by a longterm optimal balance between different transport modes. The research presented in this paper highlights the significant cost reduction opportunities possible through the densification of rail freight, especially over longer distances, with concomitant implications for increased profitability for rail operators. The densification opportunity should also place a core focus on transport corridors being developed throughout the region. SSA countries themselves can play a critical role in unlocking this potential through, inter alia, simplifying regional economic communities and taking the lead in structuring agreements with the international community.

German regulation concerning domestic or transboundary transport of hazardous goods by rail (GGVE). As of 12 December 1996

International Nuclear Information System (INIS)

1996-01-01

The full official text of the German ordinance on transport of hazardous goods by rail (GGVE) is reproduced, which officially replaces the previous ordinance of 15 Dec. 1995. The new ordinance is published for implementation of the Regulation 96/49 EC of the European Council of 23 July 1996, and for adjustment of German national law to EU legislation governing the transport of hazardous goods by rail within the European Union. (orig./CB) [de

Mobile heat storage containers and their transport by rail or road

Energy Technology Data Exchange (ETDEWEB)

Goldenberg, Philipp

2013-10-15

Mobile heat storage containers are capable of making a contribution to the meaningful use of energy which is needed for use at a location other than where it originates. The study presented in this report outlines the technology of mobile heat storage and analyses an example of its transport by rail or road. (orig.)

77 FR 69769 - Solid Waste Rail Transfer Facilities

Science.gov (United States)

2012-11-21

...] Solid Waste Rail Transfer Facilities AGENCY: Surface Transportation Board, DOT. ACTION: Final rules. SUMMARY: These final rules govern land-use-exemption permits for solid waste rail transfer facilities. The... Transportation Board over solid waste rail transfer facilities. The Act also added three new statutory provisions...

Planning of the amount of trains needed for transportation by rail

Directory of Open Access Journals (Sweden)

J. Jonaitis

2007-06-01

Full Text Available The article analyses the importance of planning process of rail transportation. Railway planning problems are presented in this paper. Planning the railways for years, months, weeks or days ahead leads to substantially different problems; in this regard railway planning problems can be strategic, tactical, operational and short-term. Another way to classify railway planning problems is based on their target: they concern the timetable, the rolling stock and the crew. Planning the structure and volume of the rolling stock is a key factor in achieving maximum efficiency of transportation by rail as well as forecasting the demand for these transport facilities. The demand for trains is a time-dependant variable which in each case should be determined by two main approaches. The first method allows us to determine quantitative parameters of rolling stock (i.e. kilometers logged, efficiency, turnover, etc.. The second is based on specially developed mathematical models relying on qualitative characteristics such as relative expenses, efficiency of the particular train, relative expenditure of resources, cost of the trains, etc. Planning the volume of the rolling stock the determination of optimal service life of the trains plays an important role. The calculations involve repair costs, number of overhauls, current expenses and operational characteristics.

Risk reduction in road and rail LPG transportation bij passive fire protection

NARCIS (Netherlands)

Molag e.a., M. (Menso)

2009-01-01

The potential reduction of risk in LPG (Liquified Petroleum Gas) road transport due to the adoption of passive fire protectionswas investigated. Experimental data available for small scale vessels fully engulfed by a fire were extended to real scale road and rail tankers through a finite elements

Risk reduction in road and rail LPG transportation by passive fire protection

NARCIS (Netherlands)

Paltrinieri, N.; Landucci, G.; Molag, M.; Bonvicini, S.; Spadoni, G.; Cozzani, V.

2009-01-01

The potential reduction of risk in LPG (Liquefied Petroleum Gas) road transport due to the adoption of passive fire protections was investigated. Experimental data available for small scale vessels fully engulfed by a fire were extended to real scale road and rail tankers through a finite elements

Scheduling freight trains in rail-rail transshipment yards

OpenAIRE

Nils Boysen; Erwin Pesch

2008-01-01

Transshipment yards, where gantry cranes allow for an effcient transshipment of containers between different freight trains, are important entities in modern railway systems and facilitate the general shift from point-to-point transport to hub-and-spoke railway systems. Modern rail-rail transshipment yards accelerate container handling, so that multiple smaller trains with equal destination can be consolidated to a reduced number of trains without jeopardizing on time deliveries. An important...

Preliminary rail access study

International Nuclear Information System (INIS)

1990-01-01

The Yucca Mountain site, located on the southwestern edge of the Nevada Test Site, is an undeveloped area under investigation as a potential site for nuclear waste disposal by the US Department of Energy. The site currently lacks rail service and an existing rail right-of-way. If the site is suitable and selected for development as a disposal site, rail service is desirable to the Office of Civilian Radioactive Waste Management Program because of the potential of rail to reduce number of shipments and costs relative to highway transportation. This preliminary report is a summary of progress to date for activities to identify and evaluate potential rail options from major rail carriers in the region to the Yucca Mountain site. It is currently anticipated that the rail spur will be operational after the year 2000. 9 refs., 13 figs., 2 tabs

Light source distribution and scattering phase function influence light transport in diffuse multi-layered media

Science.gov (United States)

Vaudelle, Fabrice; L'Huillier, Jean-Pierre; Askoura, Mohamed Lamine

2017-06-01

Red and near-Infrared light is often used as a useful diagnostic and imaging probe for highly scattering media such as biological tissues, fruits and vegetables. Part of diffusively reflected light gives interesting information related to the tissue subsurface, whereas light recorded at further distances may probe deeper into the interrogated turbid tissues. However, modelling diffusive events occurring at short source-detector distances requires to consider both the distribution of the light sources and the scattering phase functions. In this report, a modified Monte Carlo model is used to compute light transport in curved and multi-layered tissue samples which are covered with a thin and highly diffusing tissue layer. Different light source distributions (ballistic, diffuse or Lambertian) are tested with specific scattering phase functions (modified or not modified Henyey-Greenstein, Gegenbauer and Mie) to compute the amount of backscattered and transmitted light in apple and human skin structures. Comparisons between simulation results and experiments carried out with a multispectral imaging setup confirm the soundness of the theoretical strategy and may explain the role of the skin on light transport in whole and half-cut apples. Other computational results show that a Lambertian source distribution combined with a Henyey-Greenstein phase function provides a higher photon density in the stratum corneum than in the upper dermis layer. Furthermore, it is also shown that the scattering phase function may affect the shape and the magnitude of the Bidirectional Reflectance Distribution (BRDF) exhibited at the skin surface.

49 CFR 174.59 - Marking and placarding of rail cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Marking and placarding of rail cars. 174.59... RAIL General Handling and Loading Requirements § 174.59 Marking and placarding of rail cars. No person may transport a rail car carrying hazardous materials unless it is marked and placarded as required by...

Head first rails a learner's companion to ruby on rails

CERN Document Server

Griffiths, David

2009-01-01

Ready to transport your web applications into the Web 2.0 era? Head First Rails takes your programming -- and productivity -- to the max. You'll learn everything from the fundamentals of Rails scaffolding to building customized interactive web apps using Rails' rich set of tools and the MVC framework. By the time you're finished, you'll have learned more than just another web framework. You'll master database interactions, integration with Ajax and XML, rich content, and even dynamic graphing of your data -- all in a fraction of the time it takes to build the same apps with Java, PHP, ASP.NE

Vibrations control of light rail transportation vehicle via PID type fuzzy controller using parameters adaptive method

OpenAIRE

METİN, Muzaffer; GÜÇLÜ, Rahmi

2014-01-01

In this study, a conventional PID type fuzzy controller and parameter adaptive fuzzy controller are designed to control vibrations actively of a light rail transport vehicle which modeled as 6 degree-of-freedom system and compared performances of these two controllers. Rail vehicle model consists of a passenger seat and its suspension system, vehicle body, bogie, primary and secondary suspensions and wheels. The similarity between mathematical model and real system is shown by compar...

77 FR 17121 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2012-03-23

... decision may be purchased by contacting the Office of Public Assistance, Governmental Affairs, and...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, Department of Transportation. ACTION: Approval of rail cost adjustment factor. [[Page 17122

Excitation of Surface Electromagnetic Waves on Railroad Rail

Science.gov (United States)

1978-03-31

UMTA's Office of Rail Technology research programs aim to improve urban rail transportation systems safety. This rail-transit research study attempts to develop an onboard, separate and independent obstacle-detection system--Surface Electromagnetic W...

Optimal trajectory planning and train scheduling for urban rail transit systems

CERN Document Server

Wang, Yihui; van den Boom, Ton; De Schutter, Bart

2016-01-01

This book contributes to making urban rail transport fast, punctual and energy-efficient –significant factors in the importance of public transportation systems to economic, environmental and social requirements at both municipal and national levels. It proposes new methods for shortening passenger travel times and for reducing energy consumption, addressing two major topics: (1) train trajectory planning: the authors derive a nonlinear model for the operation of trains and present several approaches for calculating optimal and energy-efficient trajectories within a given schedule; and (2) train scheduling: the authors develop a train scheduling model for urban rail systems and optimization approaches with which to balance total passenger travel time with energy efficiency and other costs to the operator. Mixed-integer linear programming and pseudospectral methods are among the new methods proposed for single- and multi-train systems for the solution of the nonlinear trajectory planning problem which involv...

Rail abandonments in the South and their effect on NWPA rail shipments

International Nuclear Information System (INIS)

1988-02-01

The railroad industry will have a very critical role in the eventual shipping of commercial spent fuel and defense high-level waste as provided under the Nuclear Waste Policy Act of 1982 and the 1987 amendments. The transport of spent fuel is expected to be accomplished by rail from 19 of the South's 27 reactor sites to the proposed Yucca Mountain repository or possible monitored retrievable storage facility. The decline in total track availability, however, could significantly impact the federal government's transportation program. Particularly the situation of continuing abandonments may limit rail opportunities at numerous reactor locations. Commercial nuclear reactor sites have the unfortunate problem of not being located on Class I railroad mainline tracks. The reactor sites are generally located in areas with limited rail traffic and thus vulnerable to rail abandonment procedures. The general deregulation of the railroad industry under the Staggers Act of 1980 also assisted in making rail abandonment, through the Interstate Commerce Commission, a rather simple and quick process. The effects of deregulation, however, have provided alternatives to abandonment. In particular, the Staggers Act has led to an enormous surge in the growth of short line and regional railroads. Such railroads have been able to effectively operate rail lines which Class I railroads found unprofitable. The short lines and regionals were also encouraged to competitively negotiate contracts directly with shippers. While these railroads may help reduce the number of abandonment applications, they may also represent higher shipping costs. The South has experienced a great number of abandonments since the 1960's. Many of the abandonments have been significant in length and have affected areas near nuclear plants expected to ship by rail

Characterization of deformed pearlitic rail steel

Science.gov (United States)

Nikas, Dimitrios; Meyer, Knut Andreas; Ahlström, Johan

2017-07-01

Pearlitic steels are commonly used for railway rails because they combine good strength and wear properties. During service, the passage of trains results in a large accumulation of shear strains in the surface layer of the rail, leading to crack initiation. Knowledge of the material properties in this region is therefore important for fatigue life prediction. As the strain is limited to a thin surface layer, very large strain gradients can be found. This makes it very difficult to quantify changes in material behavior. In this study hardness measurements were performed close to the surface using the Knoop hardness test method. The orientation of the pearlitic lamellas was measured to give an overview of the deformed microstructure in the surface of the rail. Microstructural characterization of the material was done by optical microscopy and scanning electron microscopy to evaluate the changes in the microstructure due to the large deformation. A strong gradient can be observed in the top 50 μm of the rail, while deeper into the rail the microstructure of the base material is preserved.

The Rail Alignment Environmental Impact Statement: An Update

International Nuclear Information System (INIS)

Sweeney, R.

2005-01-01

On July 23,2002, the President of the United States signed into law a joint resolution of the United States Congress designating the Yucca Mountain site in Nye County, Nevada, for development as a geologic repository for the disposal of spent nuclear fuel and high-level radioactive waste. If the US. Nuclear Regulatory Commission authorizes construction of the repository and receipt and possession of spent nuclear fuel and high-level radioactive at Yucca Mountain, the U.S. Department of Energy (DOE) would be responsible for transporting these materials to the Yucca Mountain repository as part of its obligation under the Nuclear Waste Policy Act. Part of the site recommendation decision included the analysis of a nation-wide shipping campaign to the proposed repository site. The ''Final Environmental Impact Statement for a Geologic Repository for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain, Nye County, Nevada'' (February 2002) (Repository EIS) evaluated the potential impacts of the transportation of 70,000 Metric Tons of Heavy Metal spent nuclear fuel and high-level radioactive waste from 77 locations around the nation to the potential repository in Nevada over a 24 year shipping campaign. In the Repository EIS, DOE identified mostly rail as its preferred mode of transportation, both nationally and in the State of Nevada. In December 2003, based on public comments and the environmental analyses in the Repository EIS, DOE identified a preference for the Caliente rail corridor in Nevada. On April 8, 2004, DOE issued a Record of Decision (ROD) on the Mode of Transportation and Nevada Rail Corridor for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain, Nye County, Nevada. In this ROD, the DOE announced that it had decided to select the mostly rail scenario analyzed in the Repository EIS as the transportation mode both on a national basis and in the State of Nevada. Under the mostly rail

Multi-layer membrane model for mass transport in a direct ethanol fuel cell using an alkaline anion exchange membrane

Science.gov (United States)

Bahrami, Hafez; Faghri, Amir

2012-11-01

A one-dimensional, isothermal, single-phase model is presented to investigate the mass transport in a direct ethanol fuel cell incorporating an alkaline anion exchange membrane. The electrochemistry is analytically solved and the closed-form solution is provided for two limiting cases assuming Tafel expressions for both oxygen reduction and ethanol oxidation. A multi-layer membrane model is proposed to properly account for the diffusive and electroosmotic transport of ethanol through the membrane. The fundamental differences in fuel crossover for positive and negative electroosmotic drag coefficients are discussed. It is found that ethanol crossover is significantly reduced upon using an alkaline anion exchange membrane instead of a proton exchange membrane, especially at current densities higher than 500 A m

Chemical Vapor Transport Deposition of Molybdenum Disulfide Layers Using H2O Vapor as the Transport Agent

Directory of Open Access Journals (Sweden)

Shichao Zhao

2018-02-01

Full Text Available Molybdenum disulfide (MoS2 layers show excellent optical and electrical properties and have many potential applications. However, the growth of high-quality MoS2 layers is a major bottleneck in the development of MoS2-based devices. In this paper, we report a chemical vapor transport deposition method to investigate the growth behavior of monolayer/multi-layer MoS2 using water (H2O as the transport agent. It was shown that the introduction of H2O vapor promoted the growth of MoS2 by increasing the nucleation density and continuous monolayer growth. Moreover, the growth mechanism is discussed.

An Investigation into the Non-bulk Rail Freight Transport in Australia

OpenAIRE

Hadi Ghaderi; Stephen Cahoon; Hong-Oanh Nguyen

2015-01-01

In the last decade freight transport has gained further momentum in Australia, partly through significant demand growth at both domestic and international levels and partly as the result of Australia's long term need for infrastructure decision making. Amongst the freight task, non-bulk freight is the fastest growing freight task in Australia and is forecast to grow much faster than the rate of population growth and the average national GDP growth. However, rail's share in the non-bulk market...

75 FR 17462 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2010-04-06

... decision may be purchased by contacting the office of Public Assistance, Governmental Affairs, and...-2)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the second quarter 2010 Rail Cost...

Evaluation assessment of Rail Freight Transportation Research and Development Program

Energy Technology Data Exchange (ETDEWEB)

1983-02-01

This report presents an evaluation assessment of the Canadian Rail Freight Transportation Research and Development (R and D) Program. The assessment was to assist in preparing for an evaluation of the Program and to stimulate a better understanding of the broader issues and problems of evaluating R and D programs. In general, the objectives of the program are aimed at improving rail freight productivity, capacity, safety, cost, and the domestic and foreign competitive position of railway suppliers. This is to be acccomplished by stimulating a stronger industry commitment to R and D and inducing investment in new technology through joint federal-industry funding and participation in rail freight R and D projects. In view of the low funding levels of the Program, it is unlikely that it will have a significant direct impact upon these ultimate objectives. Impacts will likely only be achieved through the Program's ability to stimulate increased industrial R and D and investment in new technology. A model of the Program developed in the report shows that the critical linkages between the activities and objectives of the Program are the leadership or advocacy functions performed by the Program's managers and of the results of projects supported under the Program; and the processes of program planning and project selection. An assessment of the Program's structure indicates that there are no significant issues that would make the evaluation of the Program or its major components inadvisable. Twelve potential evaluation questions and the basic approaches required to address each of them are presented in the report. 5 figs., 10 tabs.

Multi-Layer E-Textile Circuits

Science.gov (United States)

Dunne, Lucy E.; Bibeau, Kaila; Mulligan, Lucie; Frith, Ashton; Simon, Cory

2012-01-01

Stitched e-textile circuits facilitate wearable, flexible, comfortable wearable technology. However, while stitched methods of e-textile circuits are common, multi-layer circuit creation remains a challenge. Here, we present methods of stitched multi-layer circuit creation using accessible tools and techniques.

76 FR 59483 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2011-09-26

... the decision may be purchased by contacting the Office of Public Assistance, Governmental Affairs, and...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the fourth quarter 2011 Rail Cost Adjustment...

Air Transport versus High-Speed Rail: An Overview and Research Agenda

Directory of Open Access Journals (Sweden)

Xiaoqian Sun

2017-01-01

Full Text Available The development of high-speed rail (HSR services throughout the last decades has gradually blurred the concept of competition and cooperation with air transportation. There is a wide range of studies on this subject, with a particular focus on single lines or smaller regions. This article synthesizes and discusses recently published studies in this area, while aiming to identify commonalities and deviations among different regions throughout the world, covering services from Europe, Asia, and North America. Our meta-analysis reveals that the literature is highly controversial and the results vary substantially from one region to another, and a generalization is difficult, given route-specific characteristics, such as demand distribution, network structure, and evolution of transportation modes. As a major contribution, we propose a list of five challenges as a future research agenda on HSR/air transport competition and cooperation. Among others, we see a need for the construction of an open-source dataset for large-scale multimodal transport systems, the comprehensive assessment of new emerging transport modes, and also taking into account the resilience of multimodal transport systems under disruption.

RAIL TRAFFIC VOLUME ESTIMATION BASED ON WORLD DEVELOPMENT INDICATORS

Directory of Open Access Journals (Sweden)

Luka Lazarević

2015-08-01

Full Text Available European transport policy, defined in the White Paper, supports shift from road to rail and waterborne transport. The hypothesis of the paper is that changes in the economic environment influence rail traffic volume. Therefore, a model for prediction of rail traffic volume applied in different economic contexts could be a valuable tool for the transport planners. The model was built using common Machine Learning techniques that learn from the past experience. In the model preparation, world development indicators defined by the World Bank were used as input parameters.

Sub-Transport Layer Coding

DEFF Research Database (Denmark)

Hansen, Jonas; Krigslund, Jeppe; Roetter, Daniel Enrique Lucani

2014-01-01

Packet losses in wireless networks dramatically curbs the performance of TCP. This paper introduces a simple coding shim that aids IP-layer traffic in lossy environments while being transparent to transport layer protocols. The proposed coding approach enables erasure correction while being...... oblivious to the congestion control algorithms of the utilised transport layer protocol. Although our coding shim is indifferent towards the transport layer protocol, we focus on the performance of TCP when ran on top of our proposed coding mechanism due to its widespread use. The coding shim provides gains...

Rail environmental impact: energy consumption and noise pollution assessment of different transport modes connecting Big Ben (London, UK and Eiffel Tower (Paris, FR

Directory of Open Access Journals (Sweden)

Roberto PALACIN

2014-10-01

Full Text Available This paper is set within the framework of the RailNewcastle Summer School program 2014 run by Newcastle University. It attempts to explore the sustainability credentials of railways when compared with other transport modes connecting central London with central Paris, two of Europe’s largest metropolis. Specifically, the study compares the energy consumption and noise pollution of a rail-only travel option with two other alternatives using a combination of public transport modes. The analysis includes defining the regulatory framework, sourcing and aggregating energy consumption from a number of references as well as creating noise maps for key nodes using validated tools available. The results suggest that the rail-only option has the best performance of the three options in terms of energy consumption while a bus-coach-metro combination seems to have lower noise levels than the rest. Assumptions due to lack of meaningful data made in the calculation of underground rail services are thought to have influence on the lower than expected performance of rails systems in terms of noise. The authors conclude that considering the combined outcomes of both assessments, the rail-only option is the preferred choice from a sustainability credentials perspective.

75 FR 35877 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2010-06-23

... available on our Web site, http://www.stb.dot.gov . Copies of the decision may be purchased by contacting...-3)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the third quarter 2010 rail cost...

76 FR 37191 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2011-06-24

... our Web site, http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the third quarter 2011 Rail Cost Adjustment...

75 FR 80895 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2010-12-23

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the first quarter 2011 Rail Cost Adjustment...

77 FR 37958 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2012-06-25

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the third quarter 2012 rail cost adjustment...

78 FR 37660 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2013-06-21

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board approves the third quarter 2013 Rail Cost Adjustment Factor...

78 FR 17764 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2013-03-22

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the second quarter 2013 Rail Cost Adjustment...

76 FR 16037 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2011-03-22

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the second quarter 2011 Rail Cost Adjustment...

75 FR 58019 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2010-09-23

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the fourth quarter 2010 Rail Cost Adjustment...

75 FR 17203 - National Rail Plan

Science.gov (United States)

2010-04-05

... Rail Plan AGENCY: Federal Railroad Administration (FRA), Department of Transportation (DOT). ACTION... input into the development of the long-range National Rail Plan (NRP) through an open docket. In addition, the notice presents the overall plan design, Federal Railroad Administration's (FRA) goals in...

49 CFR 37.79 - Purchase or lease of new rail vehicles by public entities operating rapid or light rail systems.

Science.gov (United States)

2010-10-01

... entities operating rapid or light rail systems. 37.79 Section 37.79 Transportation Office of the Secretary... operating rapid or light rail systems. Each public entity operating a rapid or light rail system making a... system shall ensure that the vehicle is readily accessible to and usable by individuals with disabilities...

The systems of automatic weight control of vehicles in the road and rail transport in Poland

Directory of Open Access Journals (Sweden)

2011-09-01

Full Text Available . Condition of roads in Poland, despite the on-going modernisation works is still unsatisfactory. One reason is the excessive wear caused by overloaded vehicles. This problem also applies to rail transport, although to a much lesser extent. One solution may be the system of automatic weight control of road and rail vehicles. The article describes the legal and organizational conditions of oversize vehicles inspection in Poland. Characterized current practices weighing road vehicles, based on measurements of static technology. The article includes the description of the existing applications of the automatic dynamic weighing technology, known as systems WIM (Weigh in Motion. Additionally, the weighing technology and construction of weighing stands in road and rail are characterized. The article ends with authors' conclusions indicating the direction and ways of improving the weighing control systems for vehicles.

77 FR 58910 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2012-09-24

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the fourth quarter 2012 rail cost adjustment factor (RCAF...

49 CFR 37.81 - Purchase or lease of used rail vehicles by public entities operating rapid or light rail systems.

Science.gov (United States)

2010-10-01

... entities operating rapid or light rail systems. 37.81 Section 37.81 Transportation Office of the Secretary... operating rapid or light rail systems. (a) Except as provided elsewhere in this section, each public entity operating a rapid or light rail system which, after August 25, 1990, purchases or leases a used rapid or...

The 2055 freight transportation system and the impact of near term rail improvements on TXDOT planning project management plan.

Science.gov (United States)

2016-03-01

The Texas Department of Transportation (TxDOT) is the sponsor of the project. The : project goals are to: (1) produce a framework for Texas freight transportation system in : 2055 and (2) develop a set of rail planning recommendations that will be...

A model for the estimation of energy consumption and air pollutant emissions from rail transport

DEFF Research Database (Denmark)

Lindgreen, Erik Bjørn Grønning; Sorenson, Spencer C

2003-01-01

A model is presented for the calculation of energy consumption and air pollutant emissions from rail transport. It is based on the estimation of energy consumption from a matirx describing the distribution of speeds and accelerations for operation. It is shown that calculations can be performed...

Review on Selection and Suitability of Rail Transit Station Design Pertaining to Public Safety

Science.gov (United States)

Akabal, Farah Mohd; Masirin, Mohd Idrus Haji Mohd; Abidin Akasah, Zainal; Rohani, Munzilah Md

2017-08-01

Railway has emerged as a fast, convenient, safe, clean, and low-cost alternative to air and road transportation. Many countries have invested in rail transportation. In America, Europe and Asia, large investments are planned for rail transportation. This is because congestion problems can be reduced with the introduction of rail transportation. Rail transportation involves several components which are important to ensure the smooth and safe delivery of services such as locomotives, rail stations and railway tracks. Rail transit stations are places where trains stop to pick-up and drop-off passengers. Stations are vital for many to enable them to engage in work and social commitments. This paper focuses only on the rail transit station as it is one of the important components in rail transportation. It is also considered as a key public meeting place and space for interactions in a community. The role of rail transit station and the requirements of a good rail transit station are also described in this paper. Steps in selecting the location of rail transit station include the function and facilities in rail transit station are discussed with reference to best practices and handbooks. Selection of the appropriate rail transit station locations may help users indirectly. In addition, this paper will also elucidate on the design considerations for an efficient and effective rail transit station. Design selections for the rail transit station must be balanced between aesthetic value and functional efficiency. The right design selection may help conserve energy, assure and facilitate consumers even thought a rail transit station plays a smaller role in attracting consumers compared to a shopping complex or a residential building. This will contribute towards better and greener building for a green transportation facility. Thus, with this paper it is expected to assist the relevant authority to identify important elements in the selection and determination of suitable

75 FR 51160 - Swanson Rail Transfer, L.P.-Lease and Operation Exemption-BDB Company

Science.gov (United States)

2010-08-18

... truck-rail transfer facility on the property and provide associated rail common carrier services. \\1... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35399] Swanson Rail Transfer, L.P.--Lease and Operation Exemption--BDB Company Swanson Rail Transfer, L.P. (SRT), a noncarrier...

Experience within international transport and direct rail services in meeting the IAEA requirement for a radiation protection programme(s)

International Nuclear Information System (INIS)

Billing, D.

2003-01-01

BNFL International Transport and Direct Rail Services have successfully developed appropriate Radiation Protection Programmes for their business. The business supports BNFL's worldwide Nuclear Fuel Services with key customer bases in Europe, Japan and the UK, utilising marine, rail and road modal transports. Experience in this business spans over 4 decades. The preparation of RPP's for each aspect of its operations has been made relatively straight forward in that the key elements within the internationally recognised model RPP (by WNTI) were already in place in BNFL's procedures to satisfy current National UK and International Regulations and supported by Management systems which comply with International Standards for Quality Assurance. (author)

Improved electron transport layer

DEFF Research Database (Denmark)

2012-01-01

The present invention provides: a method of preparing a coating ink for forming a zinc oxide electron transport layer, comprising mixing zinc acetate and a wetting agent in water or methanol; a coating ink comprising zinc acetate and a wetting agent in aqueous solution or methanolic solution......; a method of preparing a zinc oxide electron transporting layer, which method comprises: i) coating a substrate with the coating ink of the present invention to form a film; ii) drying the film; and iii) heating the dry film to convert the zinc acetate substantially to ZnO; a method of preparing an organic...... photovoltaic device or an organic LED having a zinc oxide electron transport layer, the method comprising, in this order: a) providing a substrate bearing a first electrode layer; b) forming an electron transport layer according to the following method: i) coating a coating ink comprising an ink according...

Definition of an On-Board Comfort Index (Rail for the Railway Transport

Directory of Open Access Journals (Sweden)

Vincenzo Barone

2017-01-01

Full Text Available The use of collective transport is strongly influenced by the quality of offered service. One of the overriding factors that affect the modal shift process is the quality of transport systems. To increase the attractiveness of collective transport services and therefore reduce the use of cars, authorities in collaboration with transport companies should take steps to ensure a high level of service quality in the public transport system. The provided quality is the level of quality achieved on daily basis and measured by the customer/user point of view. This research aims to relate service quality perceived by the user to measurements of two environmental indicators, that is, vibration, in reference to which the acceleration transmitted to the body by the vehicle motion and by its vibration will be measured, and noise, in reference to which the Equivalent Sound Pressure Level—Leq (A—will be measured. Finally, a Comfort Index (CI (rail is specified, calibrated, and validated.

The economic effects of high speed rail investment

OpenAIRE

de Rus, Ginés

2008-01-01

The allocation of traffic between different transport modes follows transport user decisions which depend on the generalized cost of travel in the available alternatives. High Speed Rail (HSR) investment is a government decision with significant effects on the generalized cost of rail transport; and therefore on the modal split in corridors where private operators compete for traffic and charge prices close to total producer costs (infrastructure included). The rationale for HSR investment is...

High Speed Rail (HSR) in the United States

Science.gov (United States)

2009-12-08

announced that it will expand the capacity on its aging high speed line between Tokyo and Osaka, the most heavily traveled intercity rail segment in the...United States, in most of these countries intercity rail travel (including both conventional and high speed rail) represents less than 10% of all...that is sometimes mentioned by its advocates. Intercity passenger rail transport is relatively safe, at least compared with highway travel . And HSR in

California statewide model for high-speed rail

OpenAIRE

Outwater, Maren; Tierney, Kevin; Bradley, Mark; Sall, Elizabeth; Kuppam, Arun; Modugala, Vamsee

2010-01-01

The California High Speed Rail Authority (CHSRA) and the Metropolitan Transportation Commission (MTC) have developed a new statewide model to support evaluation of high-speed rail alternatives in the State of California. This statewide model will also support future planning activities of the California Department of Transportation (Caltrans). The approach to this statewide model explicitly recognizes the unique characteristics of intraregional travel demand and interregional travel demand. A...

Rail Access to Yucca Mountain: Critical Issues

International Nuclear Information System (INIS)

Halstead, R. J.; Dilger, F.; Moore, R. C.

2003-01-01

The proposed Yucca Mountain repository site currently lacks rail access. The nearest mainline railroad is almost 100 miles away. Absence of rail access could result in many thousands of truck shipments of spent nuclear fuel and high-level radioactive waste. Direct rail access to the repository could significantly reduce the number of truck shipments and total shipments. The U.S. Department of Energy (DOE) identified five potential rail access corridors, ranging in length from 98 miles to 323 miles, in the Final Environmental Impact Statement (FEIS) for Yucca Mountain. The FEIS also considers an alternative to rail spur construction, heavy-haul truck (HHT) delivery of rail casks from one of three potential intermodal transfer stations. The authors examine the feasibility and cost of the five rail corridors, and DOE's alternative proposal for HHT transport. The authors also address the potential for rail shipments through the Las Vegas metropolitan area

Enhancing the connectivity of high speed rail in the Orlando-Tampa corridor with local public transportation systems : issues and opportunities.

Science.gov (United States)

2011-01-01

High Speed Rail (HSR) will only be truly transformational if it has effective connections with as many other modes of transportation as possible. This project looks at local public transportation systems that have opportunities to connect to HSR stat...

Lattice Boltzmann method for short-pulsed laser transport in a multi-layered medium

International Nuclear Information System (INIS)

Zhang, Yong; Yi, Hong-Liang; Tan, He-Ping

2015-01-01

We construct a lattice Boltzmann method (LBM) for transient radiative transfer in one-dimensional multi-layered medium with distinct refractive index in each layer. The left boundary is irradiated normally by a short-pulsed laser. The Fresnel interfaces conditions, which incorporate reflection and refraction, are used at the boundaries and the interfaces. Based on the Fresnel's law and Snell's law, the interfacial intensity formulas are introduced. The collimated and diffuse intensities are treated individually. At a transient time step, the collimated component is first solved by LBM and then embedded into the transient radiative transfer equation as a source term. To keep the consistency of the directions in all the layers, angular interpolation of the intensities at the interfaces is adopted. The transient radiative transfer in a two-layer medium is first investigated, and the time-resolved results are validated by comparing with those by the Monte Carlo method (MCM). Of particular interest, the angular intensities along the slab at different times are presented to illustrate a variety of interesting phenomena, and the discontinuous nature of the intensity at the interfaces is discussed. The effects of various parameters on the time-resolved signals are examined. - Highlights: • Transient radiative transfer in a multi-layered medium is solved by LBM. • The boundary and interfaces are all considered as Fresnel surfaces. • The LBM solution for the collimated pulse is derived. • Discontinuous nature of the intensity at the interface is illustrated and discussed

Appraisal on Rail Transit Development: A Review on Train Services and Safety

Science.gov (United States)

Nordin, Noor Hafiza binti; Masirin, Mohd Idrus Haji Mohd; Ghazali, Mohd Imran bin; Azis, Mohd Isom bin

2017-08-01

The ever increasing problems faced by population around the world have made demands that transportation need to be improved as an effective and efficient communication means. It is considered as a necessity especially when rapid development and economic growth of a country is the agenda. Among the transportation modes being focused as critical facilities are the bus system, rail system, road network, shipping system and air transportation system. Rail transport is a means of conveyance of passengers and goods by way of wheeled vehicles running on rail tracks. In Malaysia, the railway network has evolved tremendously since its inception in the early 19th century. It has grown proportionally with the national development. Railway network does not only mean for rural transportation, but it also considered as a solution to urban congestion challenges. Currently, urban rail transit is the most popular means of urban transportation system especially as big cities such as Kuala Lumpur. This paper presents the definition of rail transportation system and its role in urban or sub-urban operation. It also describes the brief history of world railway transportation including a discussion on Malaysian rail history perspective. As policy and standard are important in operating a railway system, this paper also illustrates and discusses some elements which have an impact on the effectiveness and efficiency of train operation. Towards the end, this paper also shares the importance of railway safety based on real case studies around the world. Thus, it is hoped that this paper will enable the public to understand the rail transit development and appreciate its existence as a public transportation system.

The 2055 freight transportation system and the impact of near term rail improvements on TxDOT planning : project management plan.

Science.gov (United States)

2016-03-01

The Texas Department of Transportation (TxDOT) is the sponsor of the project. The : project goals are to: (1) produce a framework for Texas freight transportation system in : 2055 and (2) develop a set of rail planning recommendations that will be...

High speed rails. Fatigue behaviour

International Nuclear Information System (INIS)

Duart, J. M.; Pero-Sanz, J. A.; Verdeja, J. I.

2005-01-01

In recent years, passenger train speed and freight train load have increased to enhance efficiency of rail road transportation. These trends have increased the severity of rail service conditions, calling for rails with greater wear resistance, strength and fatigue behaviour. In the United Stated and Europe, track site weld rails are made entirely by aluminothermic process. This work describes the results of experimental study conducted on bending fatigue strength of plain rails and aluminothermic welded rails with preheating procedures (oxipropane and air-induced propane) approved by railways authorities. Compliance with the required fatigue strength shall be ascertained by 4 point pulsating bending test in accordance with European standards by aluminothermic welding in rails. The locati method, based in the empirical Miner's law about the cumulative damage on a fatigue tested material, allows, once known the Wohler curve of the welding process in use to settle the fatigue tensile limit at 50% with only one test. The values obtained at 2.10''6 cycles for plain rails (S f =353 MPa), oxipropane preheated aluminothermic weld rails (S f =225 MPa), and propane-air induced aluminothermic weld rails (S f =210 MPa) are very similar to those resulting from test method stated in the European Standard. From our point of view and due to its ease, speediness and savings, this is the most suitable test to check the quality and compare the aluminothermic processes in use. (Author) 15 refs

Fast rail corrugation detection based on texture filtering

Science.gov (United States)

Xiao, Jie; Lu, Kaixia

2018-02-01

The condition detection of rails in high-speed railway is one of the important means to ensure the safety of railway transportation. In order to replace the traditional manual inspection, save manpower and material resources, and improve the detection speed and accuracy, it is of great significance to develop a machine vision system for locating and identifying defects on rails automatically. Rail defects exhibit different properties and are divided into various categories related to the type and position of flaws on the rail. Several kinds of interrelated factors cause rail defects such as type of rail, construction conditions, and speed and/or frequency of trains using the rail. Rail corrugation is a particular kind of defects that produce an undulatory deformation on the rail heads. In high speed train, the corrugation induces harmful vibrations on wheels and its components and reduces the lifetime of rails. This type of defects should be detected to avoid rail fractures. In this paper, a novel method for fast rail corrugation detection based on texture filtering was proposed.

75 FR 51158 - BDB Company-Acquisition Exemption-Consolidated Rail Corporation

Science.gov (United States)

2010-08-18

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35398] BDB Company--Acquisition Exemption--Consolidated Rail Corporation BDB Company (BDB), a noncarrier, has filed a verified notice of exemption under 49 CFR 1150.31 to acquire from Consolidated Rail Corporation a parcel of land...

Factors affecting radiation doses from dedicated rail transport of spent reactor fuel

International Nuclear Information System (INIS)

Martin, J.E.

1988-01-01

This paper reports there are two exposure control concerns associated with the shipment of spent reactor fuel in dedicated trains -- compliance with transportation regulations for maximum allowable radiation levels, and minimizing the dose received by the general public. This article examines the methods used to calculate the dose equivalent rates alongside stationary (transport regulations) and moving trains (public exposure) of various lengths. The factors examined include the source term, the effect of overlapping radiation fields, the speed of the train, and the location of the population relative to the train. Trains made up of series of cars that individually meet transport regulations can, as a whole, exceed transport vehicle dose equivalent rate limits by up to 23% due to overlapping radiation fields. For moving trains and the worst case analyzed -- a person located 20 feet from the tracks and a train speed of 5 mph --- 141 rail cars would have to pass by to deliver a dose equivalent of 1 mrem

Chicago-St. Louis high speed rail plan

International Nuclear Information System (INIS)

Stead, M.E.

1994-01-01

The Illinois Department of Transportation (IDOT), in cooperation with Amtrak, undertook the Chicago-St. Louis High Speed Rail Financial and Implementation Plan study in order to develop a realistic and achievable blueprint for implementation of high speed rail in the Chicago-St. Louis corridor. This report presents a summary of the Price Waterhouse Project Team's analysis and the Financial and Implementation Plan for implementing high speed rail service in the Chicago-St. Louis corridor

Chicago-St. Louis high speed rail plan

Energy Technology Data Exchange (ETDEWEB)

Stead, M.E.

1994-12-31

The Illinois Department of Transportation (IDOT), in cooperation with Amtrak, undertook the Chicago-St. Louis High Speed Rail Financial and Implementation Plan study in order to develop a realistic and achievable blueprint for implementation of high speed rail in the Chicago-St. Louis corridor. This report presents a summary of the Price Waterhouse Project Team`s analysis and the Financial and Implementation Plan for implementing high speed rail service in the Chicago-St. Louis corridor.

75 FR 16552 - High-Speed Intercity Passenger Rail (HSIPR) Program

Science.gov (United States)

2010-04-01

...; Enhancing intercity travel options; Ensuring a state of good repair of key intercity passenger rail assets... DEPARTMENT OF TRANSPORTATION Federal Railroad Administration High-Speed Intercity Passenger Rail... selections for the High-Speed Intercity Passenger Rail (HSIPR) Program. This notice builds on the program...

Guidance for consignors, rail operators and others involved in the packaging, labelling and carriage of radioactive material by rail. Pt. 5

International Nuclear Information System (INIS)

1996-01-01

This document, part of a series of guides for those concerned with the road or rail transportation of dangerous goods, provides detailed recommendations for consignors, rail operators and others involved in the packaging, labelling and carriage of radioactive materials by rail. It covers the relevant legislation and regulations on the carriage of such dangerous goods to assist those involved with compliance. (UK)

Analysis of rail accident frequencies and severities for the assessment of radioactive material transport risk - Summary report

International Nuclear Information System (INIS)

Heywood, J.D.; Schwartz, G.; Fett, J.

2001-01-01

This shortened version of the final contractual report to the European Commission DGXVII summarises the work performed and the conclusions drawn from consideration, comparison and analysis of transport accident frequency and severity assessment methods for radioactive material transport by rail. This paper aims to provide an introduction to the study whose final report is 155 pages in length. The findings are based on a comprehensive review of transport risk assessment methods and related databases available to EU member states. The emphasis has been on the probabilistic accident severity and frequency assessment methodologies developed and used by the organisations involved in this EU-funded research project - AEA Technology and GRS. The results should be of major assistance in the understanding and development of standardised quantitative risk assessment models. Further work is suggested to underpin the development of a harmonised accident methodology including the collection of more detailed rail data and analysis on a year by year basis as well as further consideration of the assumptions made for fire accident scenarios. (author)

Rail-induced Traffic in China

Directory of Open Access Journals (Sweden)

Nan He

2017-11-01

Full Text Available The rapid development of China’s railway has exerted an enormous influence on the intercity passenger transport structure in recent years. However, it has not satisfied the passengers’ travel demand due to induced traffic. This paper is committed to solving such issue, with the aim of satisfying the current travel demand, and of anticipating the demand of the predicted traffic growth over the next 20 to 30 years. The paper has considered the increase in rail passenger kilometres caused by the growth of rail kilometres as rail-induced traffic. Based on the concept and former research of induced traffic, the panel data of 26 provinces and 3 municipalities of China between the year 2000 and 2014 were collected, and the elasticity models (including elasticity-based model, distributed lag model, high-speed rail (HSR elasticity model and rail efficiency model have been constructed. The results show the importance of model formation incorporation of rail-induced traffic. It is better to get the correct value in divided zones with different train frequencies or incorporation rail efficiency in cities or provinces. The lag time and rail types also need to be considered. In summary, the results analysis not only confirms the existence of rail-induced traffic, but also provides substantial recommendations to train operation planning.

Microscopic investigation of surface layers on rails

Czech Academy of Sciences Publication Activity Database

Jirásková, Yvonna; Svoboda, Jiří; Schneeweiss, Oldřich; Daves, W.; Fischer, F. D.

2005-01-01

Roč. 239, č. 2 (2005), s. 132-141 ISSN 0169-4332 R&D Projects: GA AV ČR(CZ) IBS2041105 Institutional research plan: CEZ:AV0Z20410507 Keywords : Mössbauer phase analysis * TEM * rail Subject RIV: JO - Structural Engineering Impact factor: 1.263, year: 2005

49 CFR 38.175 - High-speed rail cars, monorails and systems.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false High-speed rail cars, monorails and systems. 38....175 High-speed rail cars, monorails and systems. (a) All cars for high-speed rail systems, including... monorail systems operating primarily on dedicated rail (i.e., not used by freight trains) or guideway, in...

Stormwater quality management in rail transportation--past, present and future.

Science.gov (United States)

Vo, Phuong Tram; Ngo, Huu Hao; Guo, Wenshan; Zhou, John L; Listowski, Andrzej; Du, Bin; Wei, Qin; Bui, Xuan Thanh

2015-04-15

Railways currently play an important role in sustainable transportation systems, owing to their substantial carrying capacity, environmental friendliness and land-saving advantages. Although total pollutant emissions from railway systems are far less than that of automobile vehicles, the pollution from railway operations should not be underestimated. To date, both scientific and practical papers dealing with stormwater management for rail tracks have solely focused on its drainage function. Unlike roadway transport, the potential of stormwater pollution from railway operations is currently mishandled. There have been very few studies into the impact of its operations on water quality. Hence, upon the realisation on the significance of nonpoint source pollution, stormwater management priorities should have been re-evaluated. This paper provides an examination of past and current practices of stormwater management in the railway industry, potential sources of stormwater pollution, obstacles faced in stormwater management and concludes with strategies for future management directions. Copyright © 2015 Elsevier B.V. All rights reserved.

Reported Design Processes for Accessibility in Rail Transport

DEFF Research Database (Denmark)

Herriott, Richard; Cook, Sharon

2014-01-01

Accessibility is a fundamental requirement in public transport (PT) yet there exists little research on design for accessibility or inclusive design (ID) in this area. This paper sets out to discover what methods are used in the rail sector to achieve accessibility goals and to examine how far...... these methods deviate from user-centred and ID norms. Semi-structured interviews were conducted with nine rolling stock producers, operators and design consultancies. The purpose was to determine if ID design methods are used explicitly and the extent to which the processes used conformed to ID (if at all......). The research found that the role of users in the design process of manufacturers was limited and that compliance with industry standards was the dominant means to achieving accessibility goals. Design consultancies were willing to apply more user-centred design if the client requested it. Where operators were...

49 CFR 210.29 - Operation standards (moving locomotives and rail cars).

Science.gov (United States)

2010-10-01

... cars). 210.29 Section 210.29 Transportation Other Regulations Relating to Transportation (Continued... REGULATIONS Inspection and Testing § 210.29 Operation standards (moving locomotives and rail cars). The operation standards for the noise emission levels of moving locomotives, rail cars, or consists of...

South Africa’s freight rail reform: A demand-driven perspective

Directory of Open Access Journals (Sweden)

Jan H. Havenga

2014-11-01

Full Text Available During the 20th century, freight transport in South Africa was employed to attain politicoeconomic ideals, resulting in the overprotection of rail and overregulation of road transport. Increasing industry pressure, combined with the international deregulation trend, led to deregulation in 1988. Myopia resulted in a rail investment hiatus and exponential growth in high-value, long-distance road transport, causing excessive logistics and externality costs for the country. The aim of this study was to propose a freight rail reform agenda based on, (1 lessons from past freight transport policy efforts and (2 the results of freight transport market segmentation driven by models developed over the past two decades. For the study, freight flows were modelled by disaggregating the national input–output model into 372 origin–destination pairs and 71 commodity groups, followed by distance decay gravitymodelling. Logistics costs were calculated by relating commodity-level freight flows to the costs of fulfilling associated logistical functions. The standard management approach of founding strategy development on market-driven segmentation provides a neutral input to steer rail reform discussions in South Africa. Market segmentation points to a dualistic rail reform agenda, enabling both a profit-driven core and a development-driven branch line network. Freight flow insights are steering the policy reform debate towards long-term freight strategy development and optimal freight logistics network design.

Used fuel rail shock and vibration testing options analysis

Energy Technology Data Exchange (ETDEWEB)

Ross, Steven B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Best, Ralph E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Klymyshyn, Nicholas A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jensen, Philip J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Maheras, Steven J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-09-25

The objective of the rail shock and vibration tests is to complete the framework needed to quantify loads of fuel assembly components that are necessary to guide materials research and establish a technical basis for review organizations such as the U.S. Nuclear Regulatory Commission (NRC). A significant body of experimental and numerical modeling data exists to quantify loads and failure limits applicable to normal conditions of transport (NCT) rail transport, but the data are based on assumptions that can only be verified through experimental testing. The test options presented in this report represent possible paths for acquiring the data that are needed to confirm the assumptions of previous work, validate modeling methods that will be needed for evaluating transported fuel on a case-by-case basis, and inform material test campaigns on the anticipated range of fuel loading. The ultimate goal of this testing is to close all of the existing knowledge gaps related to the loading of used fuel under NCT conditions and inform the experiments and analysis program on specific endpoints for their research. The options include tests that would use an actual railcar, surrogate assemblies, and real or simulated rail transportation casks. The railcar carrying the cradle, cask, and surrogate fuel assembly payload would be moved in a train operating over rail track modified or selected to impart shock and vibration forces that occur during normal rail transportation. Computer modeling would be used to help design surrogates that may be needed for a rail cask, a cask’s internal basket, and a transport cradle. The objective of the design of surrogate components would be to provide a test platform that effectively simulates responses to rail shock and vibration loads that would be exhibited by state-of-the-art rail cask, basket, and/or cradle structures. The computer models would also be used to help determine the placement of instrumentation (accelerometers and strain gauges

Multi-layers castings

Directory of Open Access Journals (Sweden)

J. Szajnar

2010-01-01

Full Text Available In paper is presented the possibility of making of multi-layers cast steel castings in result of connection of casting and welding coating technologies. First layer was composite surface layer on the basis of Fe-Cr-C alloy, which was put directly in founding process of cast carbon steel 200–450 with use of preparation of mould cavity method. Second layer were padding welds, which were put with use of TIG – Tungsten Inert Gas surfacing by welding technology with filler on Ni matrix, Ni and Co matrix with wolfram carbides WC and on the basis on Fe-Cr-C alloy, which has the same chemical composition with alloy, which was used for making of composite surface layer. Usability for industrial applications of surface layers of castings were estimated by criterion of hardness and abrasive wear resistance of type metal-mineral.

A big data analysis approach for rail failure risk assessment

NARCIS (Netherlands)

Jamshidi, A.; Faghih Roohi, S.; Hajizadeh, S.; Nunez Vicencio, Alfredo; Babuska, R.; Dollevoet, R.P.B.J.; Li, Z.; De Schutter, B.H.K.

2017-01-01

Railway infrastructure monitoring is a vital task to ensure rail transportation safety. A rail failure could result in not only a considerable impact on train delays and maintenance costs, but also on safety of passengers. In this article, the aim is to assess the risk of a rail failure by

49 CFR 213.343 - Continuous welded rail (CWR).

Science.gov (United States)

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION TRACK SAFETY STANDARDS Train Operations at Track Classes 6 and...) Designation of a desired rail installation temperature range for the geographic area in which the CWR is... installation temperature range when adjusting CWR. (b) Rail anchoring or fastening requirements that will...

77 FR 76169 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2012-12-26

....stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public Assistance...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the AAR's proposed rebasing calculations and...

Coordinated Multi-layer Multi-domain Optical Network (COMMON) for Large-Scale Science Applications (COMMON)

Energy Technology Data Exchange (ETDEWEB)

Vokkarane, Vinod [University of Massachusetts

2013-09-01

We intend to implement a Coordinated Multi-layer Multi-domain Optical Network (COMMON) Framework for Large-scale Science Applications. In the COMMON project, specific problems to be addressed include 1) anycast/multicast/manycast request provisioning, 2) deployable OSCARS enhancements, 3) multi-layer, multi-domain quality of service (QoS), and 4) multi-layer, multidomain path survivability. In what follows, we outline the progress in the above categories (Year 1, 2, and 3 deliverables).

Analyzing the Potential for High-speed Rail as Part of the Multimodal Transportation System in the United States' Midwest Corridor

Directory of Open Access Journals (Sweden)

Jeffrey C. Peters

2014-06-01

Full Text Available With increasing demand and rising fuel costs, both travel time and cost of current intercity passenger transportation modes are becoming increasingly relevant. Around the world, highspeed rail (HSR is seen as a way to alleviate demand on highways and at airports. Ridership is the critical element in determining the viability of a large capital, long-term transportation investment. This paper provides a systematic, consistent methodology for analyzing systemwide modal ridership with and without a proposed HSR network and analyzes the potential for highspeed rail as part of the existing multimodal transportation system in a region in terms of ridership. Considerations of capital investment (e.g., network design and HSR speed, along with exogenous demographic, technological, economic, and policy trends in the long-term, are used to project ridership over time. This study represents an important step toward a consistent, comprehensive economic analysis of HSR in the United States.

78 FR 17996 - MCM Rail Services LLC-Petition for Retroactive Exemption-In Sparrows Point, Md.

Science.gov (United States)

2013-03-25

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35707] MCM Rail Services... regarding a petition for an operation exemption submitted by MCM Rail Services LLC (MCM) regarding 12 miles of rail line in Sparrows Point, Md. (the Line). DATES: MCM's supplemental information is due by April...

Keeping rail on track: preliminary findings on safety culture in Australian rail.

Science.gov (United States)

Blewett, Verna; Rainbird, Sophia; Dorrian, Jill; Paterson, Jessica; Cattani, Marcus

2012-01-01

'Safety culture' is identified in the literature as a critical element of healthy and safe workplaces. How can rail organizations ensure that consistently effective work health and safety cultures are maintained across the diversity of their operations? This paper reports on research that is currently underway in the Australian rail industry aimed at producing a Model of Best Practice in Safety Culture for the industry. Located in rail organizations dedicated to the mining industry as well as urban rail and national freight operations, the research examines the constructs of organizational culture that impact on the development and maintenance of healthy and safe workplaces. The research uses a multi-method approach incorporating quantitative (survey) and qualitative (focus groups, interviews and document analysis) methods along with a participative process to identify interventions to improve the organization and develop plans for their implementation. The research uses as its analytical framework the 10 Platinum Rules, from the findings of earlier research in the New South Wales (Australia) mining industry, Digging Deeper. Data collection is underway at the time of writing and preliminary findings are presented at this stage. The research method may be adapted for use as a form of organizational review of safety and health in organizational culture.

A systems approach to reduce urban rail energy consumption

International Nuclear Information System (INIS)

González-Gil, A.; Palacin, R.; Batty, P.; Powell, J.P.

2014-01-01

Highlights: • An insightful overview of energy usage in urban rail systems is given. • The principal measures to reduce urban rail energy consumption are appraised. • A methodology is proposed to help implement energy saving schemes in urban rail. • Regenerative braking is shown to offer the greatest energy saving potential. - Abstract: There is increasing interest in the potential of urban rail to reduce the impact of metropolitan transportation due to its high capacity, reliability and absence of local emissions. However, in a context characterised by increasing capacity demands and rising energy costs, and where other transport modes are considerably improving their environmental performance, urban rail must minimise its energy use without affecting its service quality. Urban rail energy consumption is defined by a wide range of interdependent factors; therefore, a system wide perspective is required, rather than focusing on energy savings at subsystem level. This paper contributes to the current literature by proposing an holistic approach to reduce the overall energy consumption of urban rail. Firstly, a general description of this transport mode is given, which includes an assessment of its typical energy breakdown. Secondly, a comprehensive appraisal of the main practices, strategies and technologies currently available to minimise its energy use is provided. These comprise: regenerative braking, energy-efficient driving, traction losses reduction, comfort functions optimisation, energy metering, smart power management and renewable energy micro-generation. Finally, a clear, logical methodology is described to optimally define and implement energy saving schemes in urban rail systems. This includes general guidelines for a qualitative assessment and comparison of measures alongside a discussion on the principal interdependences between them. As a hypothetical example of application, the paper concludes that the energy consumption in existing urban

36 CFR 1192.175 - High-speed rail cars, monorails and systems.

Science.gov (United States)

2010-07-01

..., monorails and systems. 1192.175 Section 1192.175 Parks, Forests, and Public Property ARCHITECTURAL AND... TRANSPORTATION VEHICLES Other Vehicles and Systems § 1192.175 High-speed rail cars, monorails and systems. (a... steel-wheel-on-steel-rail technology, and monorail systems operating primarily on dedicated rail (i.e...

Highway-Rail Crossings Inventory Data

Data.gov (United States)

Department of Transportation — The entire National Highway-Rail Crossing Inventory is available in three separate downloadble files. There is a file of all current Public-at-Grade crossings. There...

Sustainable urban rail systems: Strategies and technologies for optimal management of regenerative braking energy

International Nuclear Information System (INIS)

González-Gil, Arturo; Palacin, Roberto; Batty, Paul

2013-01-01

Highlights: • Review of principal regenerative braking strategies and technologies for urban rail. • Different energy storage technologies are assessed for use in urban rail. • Optimising timetables is a preferential measure to improve energy efficiency. • Energy storage systems improve efficiency and reliability of urban rail systems. • Reversible substations allow for a complete recovery of braking energy. - Abstract: In a society characterised by increasing rates of urbanisation and growing concerns about environmental issues like climate change, urban rail transport plays a key role in contributing to sustainable development. However, in order to retain its inherent advantages in terms of energy consumption per transport capacity and to address the rising costs of energy, important energy efficiency measures have to be implemented. Given that numerous and frequent stops are a significant characteristic of urban rail, recuperation of braking energy offers a great potential to reduce energy consumption in urban rail systems. This paper presents a comprehensive overview of the currently available strategies and technologies for recovery and management of braking energy in urban rail, covering timetable optimisation, on-board and wayside Energy Storage Systems (ESSs) and reversible substations. For each measure, an assessment of their main advantages and disadvantages is provided alongside a list of the most relevant scientific studies and demonstration projects. This study concludes that optimising timetables is a preferential measure to increase the benefits of regenerative braking in any urban rail system. Likewise, it has been observed that ESSs are a viable solution to reuse regenerative energy with voltage stabilisation and energy saving purposes. Electrochemical Double Layer Capacitors has been identified as the most suitable technology for ESSs in general, although high specific power batteries such as Li-ion may become a practical option for on

Information and Telecommunications Technology – Factor of Sustainable Rail Development

Directory of Open Access Journals (Sweden)

Gheorghe-Stelian Balan

2013-12-01

Full Text Available Among today’s modes of transportation, rail remains of great interest because of its explicit advantages arising from the fact that it is the least polluting and most environmentally friendly. These are just some of the reasons why, in recent years, the European Union strategies seek to develop and implement programs to revive Community’s rail transport. The paper makes a brief analysis of the economic impact of the implementation of information and telecommunication technologies in railway transport, technologies that can contribute significantly to the achievement of sustainable, competitive and reliable transport

MASH Test 3-11 on the T131RC Bridge Rail

Science.gov (United States)

2012-10-01

Texas Department of Transportation (TxDOT) currently uses the TxDOT Type T101RC Bridge Rail, : a steel post and beam bridge rail anchored to the top of concrete curbs. The T101RC Bridge Rail is : 27 inches in height and can be anchored to the top of ...

Optimization Design of Multi-Parameters in Rail Launcher System

Directory of Open Access Journals (Sweden)

Yujiao Zhang

2014-05-01

Full Text Available Today the energy storage systems are still encumbering, therefore it is useful to think about the optimization of a railgun system in order to achieve the best performance with the lowest energy input. In this paper, an optimal design method considering 5 parameters is proposed to improve the energy conversion efficiency of a simple railgun. In order to avoid costly trials, the field- circuit method is employed to analyze the operations of different structural railguns with different parameters respectively. And the orthogonal test approach is used to guide the simulation for choosing the better parameter combinations, as well reduce the calculation cost. The research shows that the proposed method gives a better result in the energy efficiency of the system. To improve the energy conversion efficiency of electromagnetic rail launchers, the selection of more parameters must be considered in the design stage, such as the width, height and length of rail, the distance between rail pair, and pulse forming inductance. However, the relationship between these parameters and energy conversion efficiency cannot be directly described by one mathematical expression. So optimization methods must be applied to conduct design. In this paper, a rail launcher with five parameters was optimized by using orthogonal test method. According to the arrangement of orthogonal table, the better parameters’ combination can be obtained through less calculation. Under the condition of different parameters’ value, field and circuit simulation analysis were made. The results show that the energy conversion efficiency of the system is increased by 71.9 % after parameters optimization.

Evaluating primary forest fuel rail terminals with discrete event simulation: A case study from Austria

OpenAIRE

Ulrich J. Wolfsmayr; Rossana Merenda; Peter Rauch; Francesco Longo; Manfred Gronalt

2016-01-01

Biomass rail transport is a useful alternative to unimodal truck transport for medium or long transport distances, if only a short road pre-haulage is required. Up to now primary forest fuels (PFF) are rarely transported on the rail network in Austria and rail terminals able to tranship notable volumes are not established yet. The objective of this study is to investigate the potentials of existing transhipment infrastructure for introducing and operating PFF terminals. Such PFF terminals ena...

Critical infrastructures risk and vulnerability assessment in transportation of dangerous goods transportation by road and rail

CERN Document Server

Vamanu, Bogdan I; Katina, Polinpapilinho F

2016-01-01

This book addresses a key issue in today’s society: the safer transport of dangerous goods, taking into account people, the environment and economics. In particular, it offers a potential approach to identifying the issues, developing the models, providing the methods and recommending the tools to address the risks and vulnerabilities involved. We believe this can only be achieved by assessing those risks in a comprehensive, quantifiable and integrated manner. Examining both rail and road transportation, the book is divided into three sections, covering: the mature and accepted (by both academia and practitioners) methodology of risk assessment; the vulnerability assessment – a novel approach proposed as a vital complement to risk; guidance and support to build the tools that make methods and equations to yield: the Decision Support Systems. Throughout the book, the authors do not endeavor to provide THE solution. Instead, the book offers insightful food for thought for students, researchers, practitioner...

Flex Cargo Rail. Developing new service, collection and distribution concepts for the transport of freight by rail.; Flex Cargo Rail. Wege zu neuen Bedien-, Sammel- und Verteilkonzepten im Schienengueterverkehr

Energy Technology Data Exchange (ETDEWEB)

Kochsiek, Joachim [Fraunhofer-Institut fuer Materialfluss und Logistik (IML), Dortmund (Germany). Gruppe Multimodale Logistik

2010-07-01

FlexCargoRail is a concept for self propelled electric freight wagons. This will enhance rail operations on first and last mile. The concept can be integrated in the existing rail system, so migration is possible without any lost investments. Standard components from industry and rail are used to realise the FCR wagon. Motors, transmissions, control and batteries are available and approved. One of the effects is to enhance service for loading terminals. This can become independent from factory siding operation. From the economic point of view, FCR is realisable. This is shown by target costing. Efficiency of FCR is dependent from high frequent use of FCR rail cars and the use of the possibility to shunt also conventional freight wagons with FCR wagons. Migration should be carried out in logistical networks with frequent operations between plants and sidings with a closed wagon pool. (orig.)

Improving fatigue performance of rail thermite welds

Science.gov (United States)

Jezzini-Aouad, M.; Flahaut, P.; Hariri, S.; Winiar, L.

2010-06-01

Rail transport development offers economic and ecological interests. Nevertheless, it requires heavy investments in rolling material and infrastructure. To be competitive, this transportation means must rely on safe and reliable infrastructure, which requires optimization of all implemented techniques and structure. Rail thermite (or aluminothermic) welding is widely used within the railway industry for in-track welding during re-rail and defect replacement. The process provides numerous advantages against other welding technology commonly used. Obviously, future demands on train traffic are heavier axle loads, higher train speeds and increased traffic density. Thus, a new enhanced weld should be developed to prevent accidents due to fracture of welds and to lower maintenance costs. In order to improve such assembly process, a detailed metallurgical study coupled to a thermomechanical modelling of the phenomena involved in the thermite welding process is carried out. Obtained data enables us to develop a new improved thermite weld (type A). This joint is made by modifying the routinely specified procedure (type B) used in a railway rail by a standard gap alumino-thermic weld. Joints of type A and B are tested and compared. Based on experimental temperature measurements, a finite element analysis is used to calculate the thermal residual stresses induced. In the vicinity of the weld, the residual stress patterns depend on the thermal conditions during welding as it also shown by litterature [1, 2]. In parallel, X-Ray diffraction has been used to map the residual stress field that is generated in welded rail of types A and B. Their effect on fatigue crack growth in rail welds is studied. An experimental study based on fatigue tests of rails welded by conventional and improved processes adjudicates on the new advances and results will be shown.

Multi-layer micro/nanofluid devices with bio-nanovalves

Science.gov (United States)

Li, Hao; Ocola, Leonidas E.; Auciello, Orlando H.; Firestone, Millicent A.

2013-01-01

A user-friendly multi-layer micro/nanofluidic flow device and micro/nano fabrication process are provided for numerous uses. The multi-layer micro/nanofluidic flow device can comprise: a substrate, such as indium tin oxide coated glass (ITO glass); a conductive layer of ferroelectric material, preferably comprising a PZT layer of lead zirconate titanate (PZT) positioned on the substrate; electrodes connected to the conductive layer; a nanofluidics layer positioned on the conductive layer and defining nanochannels; a microfluidics layer positioned upon the nanofluidics layer and defining microchannels; and biomolecular nanovalves providing bio-nanovalves which are moveable from a closed position to an open position to control fluid flow at a nanoscale.

Multi-chamber and multi-layer thiol-ene microchip for cell culture

DEFF Research Database (Denmark)

Tan, H. Y.; Hemmingsen, Mette; Lafleur, Josiane P.

2014-01-01

We present a multi-layer and multi-chamber microfluidic chip fabricated using two different thiol-ene mixtures. Sandwiched between the thiol-ene chip layers is a commercially available membrane whose morphology has been altered with coatings of thiol-ene mixtures. Experiments have been conducted ...... with the microchip and shown that the fabricated microchip is suitable for long term cell culture....

Optical properties of metallic multi-layer films

International Nuclear Information System (INIS)

Dimmich, R.

1991-09-01

Optical properties of multi-layer films consisting of alternating layers of two different metals are studied on the basis of the Maxwell equations and the Boltzmann transport theory. The influence of free-electron scattering at the film external surface and at the interfaces is taken into account and considered as a function of the electromagnetic field frequency and the structure modulation wavelength. Derived formulas for optical coefficients are valid at low frequencies, where the skin effect is nearly classical, as well as in the near-infrared, visible and ultraviolet spectral ranges, where the skin effect has the anomalous nature. It is shown that the obtained results are apparently dependent on the values of the scattering parameters. What is more, the oscillatory nature of analyzed spectra is observed, where the two oscillation periods may appear on certain conditions. The oscillations result from the electron surface and interface scattering and their amplitudes and periods depend on the boundary conditions for free-electron scattering. Finally, the application of the interference phenomenon in dielectric layers is proposed to obtain the enhancement of the non distinct details which can appear in optical spectra of metallic films. (author). 31 refs, 6 figs

Applying the polluter-pays principle to rail: Environmental differentiation of rail access charges

Energy Technology Data Exchange (ETDEWEB)

Pons-Rigat, A.; Turro Calvet, M.; Ubalde Claver, Ll.

2016-07-01

Environmental charges to rail service operators are still at an early stage of implementation in Europe. Current schemes are dissimilar and most of them have a very limited scope or do not provide effective incentives to abate environmental impacts. This is due to several practical difficulties in implementing internalisation pricing schemes in the railway sector. The first difficulty arises from the lack of internalisation in other transport modes and the small competitive margin of railways. Increasing the overall level of rail charges could affect their survival. A second difficulty is due to the uncertainties in the valuation of external costs and in the establishment of the optimal level of charges. On top of that, the imperfect competition in the rail market and its operational and financial rigidities imply that pricing decisions could be unfair and produce undesired demand effects. These difficulties should not prevent, however, advancing towards the application to rail of adequate charging methods for its environmental costs. This paper addresses the problem of setting environmentally differentiated rail charges through an analytical approach. A generalised formulation is developed that sets the level of charges as a function of the degree of internalisation in other modes. Then, the optimal trade-off in the level of differentiation is assessed to extract general guidelines. Based on this, both the derived overall costs and benefits and the impacts on each agent are quantified. (Author)

Multi-layer service function chaining scheduling based on auxiliary graph in IP over optical network

Science.gov (United States)

Li, Yixuan; Li, Hui; Liu, Yuze; Ji, Yuefeng

2017-10-01

Software Defined Optical Network (SDON) can be considered as extension of Software Defined Network (SDN) in optical networks. SDON offers a unified control plane and makes optical network an intelligent transport network with dynamic flexibility and service adaptability. For this reason, a comprehensive optical transmission service, able to achieve service differentiation all the way down to the optical transport layer, can be provided to service function chaining (SFC). IP over optical network, as a promising networking architecture to interconnect data centers, is the most widely used scenarios of SFC. In this paper, we offer a flexible and dynamic resource allocation method for diverse SFC service requests in the IP over optical network. To do so, we firstly propose the concept of optical service function (OSF) and a multi-layer SFC model. OSF represents the comprehensive optical transmission service (e.g., multicast, low latency, quality of service, etc.), which can be achieved in multi-layer SFC model. OSF can also be considered as a special SF. Secondly, we design a resource allocation algorithm, which we call OSF-oriented optical service scheduling algorithm. It is able to address multi-layer SFC optical service scheduling and provide comprehensive optical transmission service, while meeting multiple optical transmission requirements (e.g., bandwidth, latency, availability). Moreover, the algorithm exploits the concept of Auxiliary Graph. Finally, we compare our algorithm with the Baseline algorithm in simulation. And simulation results show that our algorithm achieves superior performance than Baseline algorithm in low traffic load condition.

Multi-layered breathing architectural envelope

DEFF Research Database (Denmark)

Lund Larsen, Andreas; Foged, Isak Worre; Jensen, Rasmus Lund

2014-01-01

A multi layered breathing envelope is developed as a method of natural ventilation. The two main layers consist of mineral wool and air permeable concrete. The mineral wool works as a dynamic insulation and the permeable concrete as a heat recovery system with a high thermal mass for heat storage...

Fleet servicing facilities for testing and maintaining rail and truck radioactive waste transport systems

International Nuclear Information System (INIS)

Watson, C.D.; Hudson, B.J.; Preston, M.K.; Keith, D.A.; McCreery, P.N.; Knox, W.; Easterling, E.M.; Lamprey, A.S.; Wiedemann, G.

1980-01-01

This paper examines feasibility design concepts and feasibility studies of Fleet Servicing Facilities (FSF). Such facilities are intended to be used for routine servicing, preventive maintenance, and for performing requalification license compliance tests and inspections, minor repairs, and decontamination of both the transportation casks and their associated rail cars or tractor-trailers. None of the waste handling plants in the United States presently receiving radioactive wastes have an onsite FSF, nor is there an existing third party facility providing all of these services. This situation has caused the General Accounting Office to express concern regarding the quality of waste transport system maintenance once the transport system is placed into service. Thus a need is indicated for FSFs or their equivalent at various radioactive materials receiving sites. This paper also compares the respective capital costs and operating characteristics of the following three concepts of a spent fuel cask transportation FSF; integrated FSF, colocated FSF, and independent FSF

Modeling Freight Ocean Rail and Truck Transportation Flows to Support Policy Analyses

Energy Technology Data Exchange (ETDEWEB)

Gearhart, Jared Lee [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wang, Hao [Cornell Univ., Ithaca, NY (United States); Nozick, Linda Karen [Cornell Univ., Ithaca, NY (United States); Xu, Ningxiong [Cornell Univ., Ithaca, NY (United States)

2017-11-01

Freight transportation represents about 9.5% of GDP, is responsible for about 8% of greenhouse gas emissions and supports the import and export of about 3.6 trillion in international trade; hence it is important that our national freight transportation system is designed and operated efficiently and embodies user fees and other policies that balance costs and environmental consequences. Hence, this paper develops a mathematical model to estimate international and domestic freight flows across ocean, rail and truck modes which can be used to study the impacts of changes in our infrastructure as well as the imposition of new user fees and changes in operating policies. This model is applied to two case studies: (1) a disruption of the maritime ports at Los Angeles/Long Beach similar to the impacts that would be felt in an earthquake; and (2) implementation of new user fees at the California ports.

Optimization of multi-layered metallic shield

International Nuclear Information System (INIS)

Ben-Dor, G.; Dubinsky, A.; Elperin, T.

2011-01-01

Research highlights: → We investigated the problem of optimization of a multi-layered metallic shield. → The maximum ballistic limit velocity is a criterion of optimization. → The sequence of materials and the thicknesses of layers in the shield are varied. → The general problem is reduced to the problem of Geometric Programming. → Analytical solutions are obtained for two- and three-layered shields. - Abstract: We investigate the problem of optimization of multi-layered metallic shield whereby the goal is to determine the sequence of materials and the thicknesses of the layers that provide the maximum ballistic limit velocity of the shield. Optimization is performed under the following constraints: fixed areal density of the shield, the upper bound on the total thickness of the shield and the bounds on the thicknesses of the plates manufactured from every material. The problem is reduced to the problem of Geometric Programming which can be solved numerically using known methods. For the most interesting in practice cases of two-layered and three-layered shields the solution is obtained in the explicit analytical form.

5 steps to delivering safe, secure and reliable rail solutions for the nuclear industry

Energy Technology Data Exchange (ETDEWEB)

Connelly, C. [Direct Rail Services, Warrington (United Kingdom)

2004-07-01

Direct Rail Services (DRS) has been operating since October 1995, following the decision by parent company, British Nuclear Fuels (BNFL), to create a strategic rail transport service. The decision came after the privatisation of the rail network in the UK, when the former British Rail was superseded by a range of private organisations responsible for separate areas of the industry. Individual companies became responsible for aspects such as the operation and maintenance of the network infrastructure and for passenger and freight train services. Rather than enter into contractual arrangements with third party contractors, DRS was formed - securing both the access and reliability of transport routes and availability of the rail network, providing greater guarantees about the levels of service delivery. The strategy of bringing this area of transport in house was concurrent with that of international transport, utilising its own fleet of ships for overseas fuel movements. Freight operations began in October 1995, with the first services operating between Sellafield and the low level radioactive waste facility at Drigg.

5 steps to delivering safe, secure and reliable rail solutions for the nuclear industry

International Nuclear Information System (INIS)

Connelly, C.

2004-01-01

Direct Rail Services (DRS) has been operating since October 1995, following the decision by parent company, British Nuclear Fuels (BNFL), to create a strategic rail transport service. The decision came after the privatisation of the rail network in the UK, when the former British Rail was superseded by a range of private organisations responsible for separate areas of the industry. Individual companies became responsible for aspects such as the operation and maintenance of the network infrastructure and for passenger and freight train services. Rather than enter into contractual arrangements with third party contractors, DRS was formed - securing both the access and reliability of transport routes and availability of the rail network, providing greater guarantees about the levels of service delivery. The strategy of bringing this area of transport in house was concurrent with that of international transport, utilising its own fleet of ships for overseas fuel movements. Freight operations began in October 1995, with the first services operating between Sellafield and the low level radioactive waste facility at Drigg

Modeling Macroscopic Shape Distortions during Sintering of Multi-layers

DEFF Research Database (Denmark)

Tadesse Molla, Tesfaye

as to help achieve defect free multi-layer components. The initial thickness ratio between the layers making the multi-layer has also significant effect on the extent of camber evolution depending on the material systems. During sintering of tubular bi-layer structures, tangential (hoop) stresses are very...... large compared to radial stresses. The maximum value of hoop stress, which can generate processing defects such as cracks and coating peel-offs, occurs at the beginning of the sintering cycle. Unlike most of the models defining material properties based on porosity and grain size only, the multi...... (firing). However, unintended features like shape instabilities of samples, cracks or delamination of layers may arise during sintering of multi-layer composites. Among these defects, macroscopic shape distortions in the samples can cause problems in the assembly or performance of the final component...

77 FR 23806 - Manning Rail, Inc.-Acquisition and Operation Exemption-Manning Grain Company

Science.gov (United States)

2012-04-20

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35607] Manning Rail, Inc.--Acquisition and Operation Exemption--Manning Grain Company Manning Rail, Inc. (MRI), a noncarrier, has filed a verified notice of exemption \\1\\ under 49 CFR 1150.31 to acquire from Manning Grain Company (MGC) and...

Shock and vibration environments encountered during normal rail transportation of heavy cargo

International Nuclear Information System (INIS)

Magnuson, C.F.

1982-08-01

This study was conducted to obtain vibration and superimposed shock data during normal rail shipment of heavy cargo. The data were obtained during a regularly scheduled rail shipment of a 45-tonne (50-ton) cargo which consisted of an empty spent-fuel container, its supporting structure, and associated hoisting devices. The shipment was made over rail lines which are operated by the Atchison, Topeka, and Santa Fe Railway Company between Denver, Colorado and Albuquerque, New Mexico. The instrumented rail car was equipped with 0.38-m (15-in.) hydraulic end-of-car coupling devices. The 99 percentile levels of vibration acceleration amplitudes and single degree-of-freedom superimposed shock response spectra for the longitudinal, transverse, and vertical axes are presented

Future Parking Demand at Rail Stations in Klang Valley

Directory of Open Access Journals (Sweden)

Ho Phooi Wai

2017-01-01

Full Text Available Klang Valley, Malaysia is currently undergoing a massive development of rail transportation system expansion where the current integrated rail transit system will see new extensions of two MRT lines and an LRT line by year 2020. By year 2017, the first MRT line will be ready to run with 31 new rail stations connected to the current passenger rail network. The existing Park and Ride facilities in Klang Valley are commonly known as being unable to sufficiently cater for the current parking space demand. Therefore, with the expansion of many additional rail stations which are rapidly under construction, there are doubts that the future parking space at rail stations will be able to accommodate the sudden rise of rail passengers. Although the authorities are increasing parking bays at various locations, will the future parking demand at rail stations be sufficient? This paper studies the factors influencing parking demand in terms of population, car ownership, new car registrations and passenger rail ridership and estimating the future parking demand using Linear Regression method. Result shows that the forecasted parking demand at rail stations after the implementation of the first new MRT system in 2017 is 2.7 times more than in 2014.

Thermal conductivities of single- and multi-layer phosphorene: a molecular dynamics study.

Science.gov (United States)

Zhang, Ying-Yan; Pei, Qing-Xiang; Jiang, Jin-Wu; Wei, Ning; Zhang, Yong-Wei

2016-01-07

As a new two-dimensional (2D) material, phosphorene has drawn growing attention owing to its novel electronic properties, such as layer-dependent direct bandgaps and high carrier mobility. Herein we investigate the in-plane and cross-plane thermal conductivities of single- and multi-layer phosphorene, focusing on geometrical (sample size, orientation and layer number) and strain (compression and tension) effects. A strong anisotropy is found in the in-plane thermal conductivity with its value along the zigzag direction being much higher than that along the armchair direction. Interestingly, the in-plane thermal conductivity of multi-layer phosphorene is insensitive to the layer number, which is in strong contrast to that of graphene where the interlayer interactions strongly influence the thermal transport. Surprisingly, tensile strain leads to an anomalous increase in the in-plane thermal conductivity of phosphorene, in particular in the armchair direction. Both the in-plane and cross-plane thermal conductivities can be modulated by external strain; however, the strain modulation along the cross-plane direction is more effective and thus more tunable than that along the in-plane direction. Our findings here are of great importance for the thermal management in phosphorene-based nanoelectronic devices and for thermoelectric applications of phosphorene.

Multi-Stage Transportation Problem With Capacity Limit

Directory of Open Access Journals (Sweden)

I. Brezina

2010-06-01

Full Text Available The classical transportation problem can be applied in a more general way in practice. Related problems as Multi-commodity transportation problem, Transportation problems with different kind of vehicles, Multi-stage transportation problems, Transportation problem with capacity limit is an extension of the classical transportation problem considering the additional special condition. For solving such problems many optimization techniques (dynamic programming, linear programming, special algorithms for transportation problem etc. and heuristics approaches (e.g. evolutionary techniques were developed. This article considers Multi-stage transportation problem with capacity limit that reflects limits of transported materials (commodity quantity. Discussed issues are: theoretical base, problem formulation as way as new proposed algorithm for that problem.

An ultrasonically levitated noncontact stage using traveling vibrations on precision ceramic guide rails.

Science.gov (United States)

Koyama, Daisuke; Ide, Takeshi; Friend, James R; Nakamura, Kentaro; Ueha, Sadayuki

2007-03-01

This paper presents a noncontact sliding table design and measurements of its performance via ultrasonic levitation. A slider placed atop two vibrating guide rails is levitated by an acoustic radiation force emitted from the rails. A flexural traveling wave propagating along the guide rails allows noncontact transportation of the slider. Permitting a transport mechanism that reduces abrasion and dust generation with an inexpensive and simple structure. The profile of the sliding table was designed using the finite-element analysis (FEA) for high levitation and transportation efficiency. The prototype sliding table was made of alumina ceramic (Al2O3) to increase machining accuracy and rigidity using a structure composed of a pair of guide rails with a triangular cross section and piezoelectric transducers. Two types of transducers were used: bolt-clamped Langevin transducers and bimorph transducers. A 40-mm long slider was designed to fit atop the two rail guides. Flexural standing waves and torsional standing waves were observed along the guide rails at resonance, and the levitation of the slider was obtained using the flexural mode even while the levitation distance was less than 10 microm. The levitation distance of the slider was measured while increasing the slider's weight. The levitation pressure, rigidity, and vertical displacement amplitude of the levitating slider thus were measured to be 6.7 kN/m2, 3.0 kN/microm/m2, and less than 1 microm, respectively. Noncontact transport of the slider was achieved using phased drive of the two transducers at either end of the vibrating guide rail. By controlling the phase difference, the slider transportation direction could be switched, and a maximum thrust of 13 mN was obtained.

The rail abandonment process: A southern perspective

International Nuclear Information System (INIS)

1988-12-01

One factor in evaluating the desirability of rail transport for high-level radioactive wastes or spent fuels is the frequency, or lack thereof, with which railroad and railroad lines have been, and are, abandoned. If DOE makes a decision to use the rail option and a line is subsequently abandoned, the choice results in increased cost, time delays and possibly safety problems: Information is therefore needed prior to the decision-making process to evaluate the desirability of the rail shipping option. One result of the abandonments mentioned herein, as well as other later abandonments, is the creation of a US rail system undergoing an evolutionary process in the 1980s as far-reaching as the changes that occurred when the industry was in its infancy a century and-a-half ago. The purpose of this paper is to examine the factors leading to some of these changes by tracing the historical development of the rail abandonment process, with particular emphasis on the rise of regional railroads, their problems in the modern era and current trends in rail abandonments as well as their effects on the southeastern United States

RoadRail: An economically viable infrastructure which facilitates the transition from oil to electricity for all forms of road transport

DEFF Research Database (Denmark)

Connolly, David

2012-01-01

to convert road transport from oil to electricity. This involves the electrification of major roads so that electric cars, vans, busses, and trucks can use electricity as their primary fuel over long distance, which in this study is referred to as ‘RoadRail’. This is a new and radical alternative......In recent decades, economic renewable energy technologies have been developed for the electricity and heat sectors. Although there has been some development in the transport sector, there is still no well-establish sustainable alternatives to oil. In this study, a new alternative is proposed...... and electricity/oil costs, Denmark is presented as a case study for the installation of RoadRail. The results indicate that based on 2020 cost assumptions, RoadRail is a more socio-economic alternative than a business-as-usual using oil. This is primarily due to decreasing electric vehicle costs, decreasing...

Demand forecast for rail shipment of radioactive material in the United States

International Nuclear Information System (INIS)

Allen, G.C.; Cashwell, J.W.

1981-01-01

A summary of the market potential for radioactive material (in millions of ton-miles) is presented in tabular form. These include the following: milled uranium ore; mill tailings; natural uranium hexafluoride; enriched uranium hexafluoride; fresh fuel, spent fuel; low-level waste; transuranic waste; and high-level waste. The maximum realistic market share for rail carriers is always less than these values because of the lack of rail access to some shipping and receiving facilities, small material quantities which could most easily move by other modes, short shipping distances for certain transport segments and greater operational convenience of other modes for some material categories. While market share and revenues for radioactive material are presently small, rail carriers appear to have a market advantage for milled uranium ore, transuranic waste and high-level waste. The potential for a significantly increased market share exists for spent fuel and uranium hexafluoride. While more fresh fuel and low-level waste can be transported by rail, it is unlikely that rail market share for radioactive materials (RAM) in general will rise to the potential maximum because many of these materials have historically been moved by truck and transported in frequent, small shipments

Reference Models for Multi-Layer Tissue Structures

Science.gov (United States)

2016-09-01

function of multi-layer tissues (etiology and management of pressure ulcers ). What was the impact on other disciplines? As part of the project, a data...simplification to develop cost -effective models of surface manipulation of multi-layer tissues. Deliverables. Specimen- (or subject) and region-specific...simplification to develop cost -effective models of surgical manipulation. Deliverables. Specimen-specific surrogate models of upper legs confirmed against data

Multi-Stage Transportation Problem With Capacity Limit

OpenAIRE

I. Brezina; Z. Čičková; J. Pekár; M. Reiff

2010-01-01

The classical transportation problem can be applied in a more general way in practice. Related problems as Multi-commodity transportation problem, Transportation problems with different kind of vehicles, Multi-stage transportation problems, Transportation problem with capacity limit is an extension of the classical transportation problem considering the additional special condition. For solving such problems many optimization techniques (dynamic programming, linear programming, special algor...

Rail Vehicle Vibrations Control Using Parameters Adaptive PID Controller

Directory of Open Access Journals (Sweden)

Muzaffer Metin

2014-01-01

Full Text Available In this study, vertical rail vehicle vibrations are controlled by the use of conventional PID and parameters which are adaptive to PID controllers. A parameters adaptive PID controller is designed to improve the passenger comfort by intuitional usage of this method that renews the parameters online and sensitively under variable track inputs. Sinusoidal vertical rail misalignment and measured real rail irregularity are considered as two different disruptive effects of the system. Active vibration control is applied to the system through the secondary suspension. The active suspension application of rail vehicle is examined by using 5-DOF quarter-rail vehicle model by using Manchester benchmark dynamic parameters. The new parameters of adaptive controller are optimized by means of genetic algorithm toolbox of MATLAB. Simulations are performed at maximum urban transportation speed (90 km/h of the rail vehicle with ±5% load changes of rail vehicle body to test the robustness of controllers. As a result, superior performance of parameters of adaptive controller is determined in time and frequency domain.

Development of rail access to the proposed repository site at Yucca Mountain

International Nuclear Information System (INIS)

Standish, P.N.; Seidler, P.E.; Andrews, W.B.; Shearin, G.

1991-01-01

In accordance with the Nuclear Waste Policy Amendment Act of 1987, Yucca Mountain was designated as the initial site to be investigated as a potential repository for the disposal of high-level radioactive waste. The Yucca Mountain site is an undeveloped area located on the southwestern edge of the Nevada Test Site (NTS), about 100 miles northwest of Las Vegas. The site currently lacks rail service or an existing right-of-way. If the Yucca Mountain site is found suitable for the repository, rail service is considered desirable by the Office of Civilian Radioactive Waste Management (OCRWM) program because of the potential of rail transportation to reduce (1) costs and (2) number of shipments, relative to highway transportation. Therefore, it is necessary to conduct a study to determine (1) that there are alignments for a potential rail line from existing mainline railroads to Yucca Mountain and (2) that these are consistent with present rail design standards and are acceptable relative to environmental and land access considerations

Experimental analysis on stress wave in inhomogeneous multi-layered structures

International Nuclear Information System (INIS)

Cho, Yun Ho; Ham, Hyo Sick

1998-01-01

The guided wave propagation in inhomogeneous multi-layered structures is experimentally explored based on theoretical dispersion curves. It turns out that proper selection of incident angle and frequency is critical for guided wave generation in multi-layered structures. Theoretical dispersion curves greatly depend on adhesive zone thickness, layer thickness and material properties. It was possible to determine the adhesive zone thickness of an inhomogeneous multi-layered structure by monitoring experimentally the change of dispersion curves.

HRTPO strategic campaign and vision plan for passenger rail : phase 1 overview.

Science.gov (United States)

2010-03-17

SUBJECT: : TEMS (Transportation Economics & Management Systems, Inc.), the consultant specializing in : passenger rail planning, was secured by the HRTPO and its partner DRPT to evaluate the potential : passenger rail service alternative defined by t...

49 CFR 1580.101 - Rail security coordinator.

Science.gov (United States)

2010-10-01

... system of transportation, when notified by TSA in writing, that a threat exists concerning that operation.... This section applies to: (1) Each freight railroad carrier that operates rolling equipment on track that is part of the general railroad system of transportation. (2) Each rail hazardous materials...

Planning, Investment, Construction and Operation of Rail Transit in Beijing

Institute of Scientific and Technical Information of China (English)

2012-01-01

In Beijing, the rail transit firstly came into existence in the mid 1960s and was officially put into operation for civil use in the early 1980s. It has entered a period of rapid development since 2001, with thanks to the coming of the Olympic Games in 2008, and has been playing a more and more important role in the passenger transport of Beijing since then on, as a key part of the public transportation. Based on a resume on the evolution of rail transit development in Beijing, this paper analyzes the mechanism of policy-making, the mode of investment and financing, the procedure of construction, and the management of operation of rail transit, all of which ensure its rapid development and effective performance.

RailSiTe® (Rail Simulation and Testing

Directory of Open Access Journals (Sweden)

Martin Johne

2016-10-01

Full Text Available RailSiTe® (Rail Simulation and Testing is DLR’s rail simulation and testing laboratory (see Figure 1. It is the implementation of a fully modular concept for the simulation of on-board and trackside control and safety technology. The RailSiTe® laboratory additionally comprises the RailSET (Railway Simulation Environment for Train Drivers and Operators human-factors laboratory, a realistic environment containing a realistic train mockup including 3D simulation.

Polyethers with pendent phenylvinyl substituted carbazole rings as polymers for hole transporting layers of OLEDs

Science.gov (United States)

Griniene, R.; Liu, L.; Tavgeniene, D.; Sipaviciute, D.; Volyniuk, D.; Grazulevicius, J. V.; Xie, Z.; Zhang, B.; Leduskrasts, K.; Grigalevicius, S.

2016-01-01

Polyethers containing pendent 3-(2-phenylvinyl)carbazole moieties have been synthesized by the multi-step synthetic routes. Full characterization of their structures is presented. The polymers represent materials of high thermal stability with initial thermal degradation temperatures exceeding 370 °C. The glass transition temperatures of the amorphous materials were in the range of 56-658 °C. The electron photoemission spectra of thin layers of the polymers showed ionization potentials of about 5.6 eV. Hole-transporting properties of the polymeric materials were tested in the structures of organic light emitting diodes with Alq3 as the green emitter and electron transporting layer. The device containing hole-transporting layers of poly{9-[6-(3-methyloxetan-3-ylmethoxy)hexyl]-3-(2-phenylvinyl)carbazole} exhibited the best overall performance with a maximum photometric efficiency of about 4.0 cd/A and maximum brightness exceeding 6430 cd/m2.

Road, rail, and air transportation noise in residential and workplace neighborhoods and blood pressure (RECORD Study).

Science.gov (United States)

Méline, Julie; Van Hulst, Andraea; Thomas, Frederique; Chaix, Basile

2015-01-01

Associations between road traffic noise and hypertension have been repeatedly documented, whereas associations with rail or total road, rail, and air (RRA) traffic noise have rarely been investigated. Moreover, most studies of noise in the environment have only taken into account the residential neighborhood. Finally, few studies have taken into account individual/neighborhood confounders in the relationship between noise and hypertension. We performed adjusted multilevel regression analyses using data from the 7,290 participants of the RECORD Study to investigate the associations of outdoor road, rail, air, and RRA traffic noise estimated at the place of residence, at the workplace, and in the neighborhoods around the residence and workplace with systolic blood pressure (SBP), diastolic blood pressure (DBP), and hypertension. Associations were documented between higher outdoor RRA and road traffic noise estimated at the workplace and a higher SBP [+1.36 mm of mercury, 95% confidence interval (CI): +0.12, +2.60 for 65-80 dB(A) vs 30-45 dB(A)] and DBP [+1.07 (95% CI: +0.28, +1.86)], after adjustment for individual/neighborhood confounders. These associations remained after adjustment for risk factors of hypertension. Associations were documented neither with rail traffic noise nor for hypertension. Associations between transportation noise at the workplace and blood pressure (BP) may be attributable to the higher levels of road traffic noise at the workplace than at the residence. To better understand why only noise estimated at the workplace was associated with BP, our future work will combine Global Positioning System (GPS) tracking, assessment of noise levels with sensors, and ambulatory monitoring of BP.

Road, rail, and air transportation noise in residential and workplace neighborhoods and blood pressure (RECORD Study

Directory of Open Access Journals (Sweden)

Julie Méline

2015-01-01

Full Text Available Associations between road traffic noise and hypertension have been repeatedly documented, whereas associations with rail or total road, rail, and air (RRA traffic noise have rarely been investigated. Moreover, most studies of noise in the environment have only taken into account the residential neighborhood. Finally, few studies have taken into account individual/neighborhood confounders in the relationship between noise and hypertension. We performed adjusted multilevel regression analyses using data from the 7,290 participants of the RECORD Study to investigate the associations of outdoor road, rail, air, and RRA traffic noise estimated at the place of residence, at the workplace, and in the neighborhoods around the residence and workplace with systolic blood pressure (SBP, diastolic blood pressure (DBP, and hypertension. Associations were documented between higher outdoor RRA and road traffic noise estimated at the workplace and a higher SBP [+1.36 mm of mercury, 95% confidence interval (CI: +0.12, +2.60 for 65-80 dB(A vs 30-45 dB(A] and DBP [+1.07 (95% CI: +0.28, +1.86], after adjustment for individual/neighborhood confounders. These associations remained after adjustment for risk factors of hypertension. Associations were documented neither with rail traffic noise nor for hypertension. Associations between transportation noise at the workplace and blood pressure (BP may be attributable to the higher levels of road traffic noise at the workplace than at the residence. To better understand why only noise estimated at the workplace was associated with BP, our future work will combine Global Positioning System (GPS tracking, assessment of noise levels with sensors, and ambulatory monitoring of BP.

Design of a Multi-layer Lane-Level Map for Vehicle Route Planning

Directory of Open Access Journals (Sweden)

Liu Chaoran

2017-01-01

Full Text Available With the development of intelligent transportation system, there occurs further demand for high precision localization and route planning, and simultaneously the traditional road-level map fails to meet with this requirement, by which this paper is motivated. In this paper, t he three-layer lane-level map architecture for vehicle path guidance is established, and the mathematical models of road-level layer, intermediate layer and lane-level layer are designed considering efficiency and precision. The geometric model of the lane-level layer of the map is characterized by Cubic Hermite Spline for continuity. A method of generating the lane geometry with fixed and variable control points is proposed, which can effectively ensure the accuracy with limited num ber of control points. In experimental part, a multi-layer map of an intersection is built to validate the map model, and an example of a local map was generated with the lane-level geometry.

Field monitoring of rail squats using 3D ultrasonic mapping technique

International Nuclear Information System (INIS)

Kaewunruen, S.; Ishida, M.

2014-01-01

Rail squats and studs are typically classified as the propagation of any cracks .that have grown longitudinally through the subsurface. Some of the cracks could propagate to the bottom of rails transversely, which have branched from the initial longitudinal cracks with a depression of rail surface. The rail defects are commonly referred to as 'squats' when they were initiated from a damage layer caused by rolling contact fatigue, and as 'studs' when they were associated with a white etching layer caused by the transformation from pearlitic steel due to friction heat generated by wheel sliding or excessive traction. Such above-mentioned rail defects have been often observed in railway tracks catered for either light passenger or heavy freight traffics and for low, medium or high speed trains all over the world for over 60 years except some places such as sharp curves where large wear takes place under severe friction between the wheel flange and rail gauge face. It becomes a much-more significant issue when the crack grows and sometimes flakes off the rail (by itself or by insufficient rail grinding), resulting in a rail surface irregularity. Such rail surface defects induce wheel/rail impact and large amplitude vibration of track structure and poor ride quality. In Australia, Europe, and Japan, rail squats/studs have occasionally turned into broken rails. The root cause and preventive solution to this defect are still under investigation from the fracture mechanics and material sciences point of view. Some patterns of squat/stud development related to both curve and tangent track geometries have been observed and squat growth has been monitored for individual squats using ultrasonic mapping techniques. This paper highlights the field monitoring of squat/stud distribution and its growth. Squat/stud growth has been detected and scanned using the ultrasonic measurement device on a grid applied to the rail surface. The depths of crack paths at each grid node form a

Field monitoring of rail squats using 3D ultrasonic mapping technique

Energy Technology Data Exchange (ETDEWEB)

Kaewunruen, S., E-mail: sakdirat.kaewunruen@transport.nsw.gov.au [NSW, Transport, Sydney (Australia); Ishida, M., E-mail: ishida-mk@n-koei.jp [Nippon Koei Co. Ltd., Railway Div., Railway Engineering Dept., Chiyoda-ku, Tokyo (Japan)

2014-11-15

Rail squats and studs are typically classified as the propagation of any cracks .that have grown longitudinally through the subsurface. Some of the cracks could propagate to the bottom of rails transversely, which have branched from the initial longitudinal cracks with a depression of rail surface. The rail defects are commonly referred to as 'squats' when they were initiated from a damage layer caused by rolling contact fatigue, and as 'studs' when they were associated with a white etching layer caused by the transformation from pearlitic steel due to friction heat generated by wheel sliding or excessive traction. Such above-mentioned rail defects have been often observed in railway tracks catered for either light passenger or heavy freight traffics and for low, medium or high speed trains all over the world for over 60 years except some places such as sharp curves where large wear takes place under severe friction between the wheel flange and rail gauge face. It becomes a much-more significant issue when the crack grows and sometimes flakes off the rail (by itself or by insufficient rail grinding), resulting in a rail surface irregularity. Such rail surface defects induce wheel/rail impact and large amplitude vibration of track structure and poor ride quality. In Australia, Europe, and Japan, rail squats/studs have occasionally turned into broken rails. The root cause and preventive solution to this defect are still under investigation from the fracture mechanics and material sciences point of view. Some patterns of squat/stud development related to both curve and tangent track geometries have been observed and squat growth has been monitored for individual squats using ultrasonic mapping techniques. This paper highlights the field monitoring of squat/stud distribution and its growth. Squat/stud growth has been detected and scanned using the ultrasonic measurement device on a grid applied to the rail surface. The depths of crack paths at each

The transportation institutional plan: Cooperative planning for NWPA transportation

International Nuclear Information System (INIS)

Denny, S.H.; Livingston-Behan, E.A.

1987-01-01

The Transportation Institutional Plan, published in 1986 by the U.S. Department of Energy's Office of Civilian Radioactive Waste Management (OCRWM), defines a process for effective interaction among those who may be affected by transportation activities conducted under provisions of the Nuclear Waste Policy Act of 1982 (NWPA). The Plan describes formal mechanisms for identifying, addressing, and resolving specific transportation issues. An appendix to the Plan includes detailed discussion of the following transportation issues: (1) the transportation of defense waste; (2) prenotification; (3) physical and rail shipments; (4) highway routing; (5) rail routing; (6) inspection and enforcement for highway and rail shipments; (7) emergency response; (8) liability coverage for transportation to NWPA facilities; (9) cask design and testing; (10) overweight truck shipments; (11) rail service analysis; (12) mixture of transportation modes; (13) transportation infrastructure improvements; (14) OCRWM training standards; (15) transportation operational procedures; and (16) State, Tribal, and local regulation of transportation. The OCRWM's intent is to provide an open accounting of planning, to identify opportunities for public involvement in program activities, and to foster communication and negotiation in the cooperative development of a safe, efficient, and cost-effective NWPA transportation program

Collaborative-Hybrid Multi-Layer Network Control for Emerging Cyber-Infrastructures

Energy Technology Data Exchange (ETDEWEB)

Lehman, Tom [USC; Ghani, Nasir [UNM; Boyd, Eric [UCAID

2010-08-31

At a high level, there were four basic task areas identified for the Hybrid-MLN project. They are: o Multi-Layer, Multi-Domain, Control Plane Architecture and Implementation, including OSCARS layer2 and InterDomain Adaptation, Integration of LambdaStation and Terapaths with Layer2 dynamic provisioning, Control plane software release, Scheduling, AAA, security architecture, Network Virtualization architecture, Multi-Layer Network Architecture Framework Definition; o Heterogeneous DataPlane Testing; o Simulation; o Project Publications, Reports, and Presentations.

Young’s modulus of multi-layer microcantilevers

Directory of Open Access Journals (Sweden)

Zhikang Deng

2017-12-01

Full Text Available A theoretical model for calculating the Young’s modulus of multi-layer microcantilevers with a coating is proposed, and validated by a three-dimensional (3D finite element (FE model using ANSYS parametric design language (APDL and atomic force microscopy (AFM characterization. Compared with typical theoretical models (Rayleigh-Ritz model, Euler-Bernoulli (E-B beam model and spring mass model, the proposed theoretical model can obtain Young’s modulus of multi-layer microcantilevers more precisely. Also, the influences of coating’s geometric dimensions on Young’s modulus and resonant frequency of microcantilevers are discussed. The thickness of coating has a great influence on Young’s modulus and resonant frequency of multi-layer microcantilevers, and the coating should be considered to calculate Young’s modulus more precisely, especially when fairly thicker coating is employed.

Atlanta Rail Yard Study: Evaluation of local-scale air pollution ...

Science.gov (United States)

Intermodal rail yards are important nodes in the freight transportation network, where freight is organized and moved from one mode of transport to another, critical equipment is serviced, and freight is routed to its next destination. Rail yard environments are also areas with multiple sources of air pollutant emissions (e.g., heavy-duty vehicles, locomotives, cranes), which may affect local air quality in residential areas nearby. In order to understand emissions and related air quality impacts, two field studies took place over the time span of 2010-2012 to measure air pollution trends in close proximity to the Inman and Tilford rail yard complex in Atlanta, GA. One field study involved long-term stationary monitoring of black carbon, fine particles, and carbon dioxide at two stations nearby the rail yard. In addition, a second field study performed intensive mobile air monitoring for a one month period in the summer of 2012 at a roadway network surrounding the rail yard complex and measured a comprehensive array of pollutants. Real-time mobile particulate measurements included particle counts, extinction coefficient, black carbon via light-absorption and particle incandescence, and particle composition derived by aerosol mass spectrometry. Gas-phase measurements included oxides of nitrogen, sulfur dioxide, carbon dioxide, and air toxics (e.g., benzene). Both sets of measurements determined detectable local influence from rail yard-related emissions.

Investigating the lubricity and electrical insulation caused by sanding in dry wheel–rail contacts

NARCIS (Netherlands)

Arias-Cuevas, O.; Li, Z.; Lewis, R.

2009-01-01

The adhesion (or available friction) in the wheel–rail contact is the most important parameter for the braking and traction operation of rail vehicles. Since the beginning of railway transportation, sanding from the locomotive has been a common practice to enhance the wheel–rail adhesion. In recent

Resonant tunneling with high peak to valley current ratio in SiO2/nc-Si/SiO2 multi-layers at room temperature

International Nuclear Information System (INIS)

Chen, D. Y.; Sun, Y.; He, Y. J.; Xu, L.; Xu, J.

2014-01-01

We have investigated carrier transport in SiO 2 /nc-Si/SiO 2 multi-layers by room temperature current-voltage measurements. Resonant tunneling signatures accompanied by current peaks are observed. Carrier transport in the multi-layers were analyzed by plots of ln(I/V 2 ) as a function of 1/V and ln(I) as a function of V 1/2 . Results suggest that besides films quality, nc-Si and barrier sub-layer thicknesses are important parameters that restrict carrier transport. When thicknesses are both small, direct tunneling dominates carrier transport, resonant tunneling occurs only at certain voltages and multi-resonant tunneling related current peaks can be observed but with peak to valley current ratio (PVCR) values smaller than 1.5. When barrier thickness is increased, trap-related and even high field related tunneling is excited, causing that multi-current peaks cannot be observed clearly, only one current peak with higher PVCR value of 7.7 can be observed. While if the thickness of nc-Si is large enough, quantum confinement is not so strong, a broad current peak with PVCR value as high as 60 can be measured, which may be due to small energy difference between the splitting energy levels in the quantum dots of nc-Si. Size distribution in a wide range may cause un-controllability of the peak voltages

76 FR 63991 - Midwest Rail d/b/a Toledo, Lake Erie and Western Railway-Lease and Operation Exemption-Toledo...

Science.gov (United States)

2011-10-14

... provide common carrier rail service over the Line, connecting with and interchanging traffic with NSR, and... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35555] Midwest Rail d/b/a... Railway and Museum, Inc. Midwest Rail d/b/a Toledo, Lake Erie and Western Railway (Toledo), a noncarrier...

Diffusion layer modeling for condensation with multi-component noncondensable gases

International Nuclear Information System (INIS)

Peterson, P.F.

1999-01-01

Many condensation problems involving noncondensable gases have multiple noncondensable species, for example air (with nitrogen, oxygen, and other gases); and other problems where light gases like hydrogen may mix with heavier gases like nitrogen. Particularly when the binary mass diffusion coefficients of the noncondensable species are substantially different, the noncondensable species tend to segregate in the condensation boundary layer. This paper presents a fundamental analysis of the mass transport with multiple noncondensable species, identifying a simple method to calculate an effective mass diffusion coefficient that can be used with the simple diffusion layer model, and discusses in detail the effects of using mass and mole based quantities, and various simplifying approximations, on predicted condensation rates. The results are illustrated with quantitative examples to demonstrate the potential importance of multi-component noncondensable gas effects

MATERIAL DEPENDENCE OF TEMPERATURE DISTRIBUTION IN MULTI-LAYER MULTI-METAL COOKWARE

Directory of Open Access Journals (Sweden)

MOHAMMADREZA SEDIGH

2017-09-01

Full Text Available Laminated structure is becoming more popular in cookware markets; however, there seems to be a lack of enough scientific studies to evaluate its pros and cons, and to show that how it functions. A numerical model using a finite element method with temperature-dependent material properties has been performed to investigate material and layer dependence of temperature distribution in multi-layer multi-metal plate exposed to irregular heating. Behavior of two parameters including mean temperature value and uniformity on the inner surface of plate under variations of thermal properties and geometrical conditions have been studied. The results indicate that conductive metals used as first layer in bi-layer plates have better thermal performance than those used in the second layer. In addition, since cookware manufacturers increasingly prefer to use all-clad aluminium plate, recently, this structure is analysed in the present study as well. The results show all-clad copper and aluminum plate possesses lower temperature gradient compared with single layer aluminum and all-clad aluminum core plates.

Modeling and Simulating Passenger Behavior for a Station Closure in a Rail Transit Network

Science.gov (United States)

Yin, Haodong; Han, Baoming; Li, Dewei; Wu, Jianjun; Sun, Huijun

2016-01-01

A station closure is an abnormal operational situation in which the entrances or exits of a rail transit station have to be closed for some time due to an unexpected incident. A novel approach is developed to estimate the impacts of the alternative station closure scenarios on both passenger behavioral choices at the individual level and passenger demand at the disaggregate level in a rail transit network. Therefore, the contributions of this study are two-fold: (1) A basic passenger behavior optimization model is mathematically constructed based on 0–1 integer programming to describe passengers’ responses to alternative origin station closure scenarios and destination station closure scenarios; this model also considers the availability of multi-mode transportation and the uncertain duration of the station closure; (2) An integrated solution algorithm based on the passenger simulation is developed to solve the proposed model and to estimate the effects of a station closure on passenger demand in a rail transit network. Furthermore, 13 groups of numerical experiments based on the Beijing rail transit network are performed as case studies with 2,074,267 records of smart card data. The comparisons of the model outputs and the manual survey show that the accuracy of our proposed behavior optimization model is approximately 80%. The results also show that our model can be used to capture the passenger behavior and to quantitatively estimate the effects of alternative closure scenarios on passenger flow demand for the rail transit network. Moreover, the closure duration and its overestimation greatly influence the individual behavioral choices of the affected passengers and the passenger demand. Furthermore, if the rail transit operator can more accurately estimate the closure duration (namely, as g approaches 1), the impact of the closure can be somewhat mitigated. PMID:27935963

Modeling and Simulating Passenger Behavior for a Station Closure in a Rail Transit Network.

Directory of Open Access Journals (Sweden)

Haodong Yin

Full Text Available A station closure is an abnormal operational situation in which the entrances or exits of a rail transit station have to be closed for some time due to an unexpected incident. A novel approach is developed to estimate the impacts of the alternative station closure scenarios on both passenger behavioral choices at the individual level and passenger demand at the disaggregate level in a rail transit network. Therefore, the contributions of this study are two-fold: (1 A basic passenger behavior optimization model is mathematically constructed based on 0-1 integer programming to describe passengers' responses to alternative origin station closure scenarios and destination station closure scenarios; this model also considers the availability of multi-mode transportation and the uncertain duration of the station closure; (2 An integrated solution algorithm based on the passenger simulation is developed to solve the proposed model and to estimate the effects of a station closure on passenger demand in a rail transit network. Furthermore, 13 groups of numerical experiments based on the Beijing rail transit network are performed as case studies with 2,074,267 records of smart card data. The comparisons of the model outputs and the manual survey show that the accuracy of our proposed behavior optimization model is approximately 80%. The results also show that our model can be used to capture the passenger behavior and to quantitatively estimate the effects of alternative closure scenarios on passenger flow demand for the rail transit network. Moreover, the closure duration and its overestimation greatly influence the individual behavioral choices of the affected passengers and the passenger demand. Furthermore, if the rail transit operator can more accurately estimate the closure duration (namely, as g approaches 1, the impact of the closure can be somewhat mitigated.

Modeling and Simulating Passenger Behavior for a Station Closure in a Rail Transit Network.

Science.gov (United States)

Yin, Haodong; Han, Baoming; Li, Dewei; Wu, Jianjun; Sun, Huijun

2016-01-01

A station closure is an abnormal operational situation in which the entrances or exits of a rail transit station have to be closed for some time due to an unexpected incident. A novel approach is developed to estimate the impacts of the alternative station closure scenarios on both passenger behavioral choices at the individual level and passenger demand at the disaggregate level in a rail transit network. Therefore, the contributions of this study are two-fold: (1) A basic passenger behavior optimization model is mathematically constructed based on 0-1 integer programming to describe passengers' responses to alternative origin station closure scenarios and destination station closure scenarios; this model also considers the availability of multi-mode transportation and the uncertain duration of the station closure; (2) An integrated solution algorithm based on the passenger simulation is developed to solve the proposed model and to estimate the effects of a station closure on passenger demand in a rail transit network. Furthermore, 13 groups of numerical experiments based on the Beijing rail transit network are performed as case studies with 2,074,267 records of smart card data. The comparisons of the model outputs and the manual survey show that the accuracy of our proposed behavior optimization model is approximately 80%. The results also show that our model can be used to capture the passenger behavior and to quantitatively estimate the effects of alternative closure scenarios on passenger flow demand for the rail transit network. Moreover, the closure duration and its overestimation greatly influence the individual behavioral choices of the affected passengers and the passenger demand. Furthermore, if the rail transit operator can more accurately estimate the closure duration (namely, as g approaches 1), the impact of the closure can be somewhat mitigated.

Integrated risk reduction framework to improve railway hazardous materials transportation safety

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiang, E-mail: liu94@illinois.edu; Saat, M. Rapik, E-mail: mohdsaat@illinois.edu; Barkan, Christopher P.L., E-mail: cbarkan@illinois.edu

2013-09-15

Highlights: • An integrated framework is developed to optimize risk reduction. • A negative binomial regression model is developed to analyze accident-cause-specific railcar derailment probability. • A Pareto-optimality technique is applied to determine the lowest risk given any level of resource. • A multi-attribute decision model is developed to determine the optimal amount of investment for risk reduction. • The models could aid the government and rail industry in developing cost-efficient risk reduction policy and practice. -- Abstract: Rail transportation plays a critical role to safely and efficiently transport hazardous materials. A number of strategies have been implemented or are being developed to reduce the risk of hazardous materials release from train accidents. Each of these risk reduction strategies has its safety benefit and corresponding implementation cost. However, the cost effectiveness of the integration of different risk reduction strategies is not well understood. Meanwhile, there has been growing interest in the U.S. rail industry and government to best allocate resources for improving hazardous materials transportation safety. This paper presents an optimization model that considers the combination of two types of risk reduction strategies, broken rail prevention and tank car safety design enhancement. A Pareto-optimality technique is used to maximize risk reduction at a given level of investment. The framework presented in this paper can be adapted to address a broader set of risk reduction strategies and is intended to assist decision makers for local, regional and system-wide risk management of rail hazardous materials transportation.

The Impedance of Multi-layer Vacuum Chambers

CERN Document Server

Vos, L

2003-01-01

Many components of the LHC vacuum chamber have multi-layered walls : the copper coated cold beam screen, the titanium coated ceramic chamber of the dump kickers, the ceramic chamber of the injection kickers coated with copper stripes, only to name a few. Theories and computer programs are available for some time already to evaluate the impedance of these elements. Nevertheless, the algorithm developed in this paper is more convenient in its application and has been used extensively in the design phase of multi-layer LHC vacuum chamber elements. It is based on classical transmission line theory. Closed expressions are derived for simple layer configurations, while beam pipes involving many layers demand a chain calculation. The algorithm has been tested with a number of published examples and was verified with experimental data as well.

Passenger train emergency systems : development of prototype railEXODUS software for U.S. passenger rail car egress.

Science.gov (United States)

2014-11-01

The Federal Railroad Administration (FRA), U.S. Department of Transportation (U.S. DOT), is sponsoring a research program, which includes investigation of the applicability of time-based egress performance requirements to U.S. passenger rail cars. Th...

Investigation of aperiodic W/C multi-layer mirror for X-ray optics

International Nuclear Information System (INIS)

Wang Zhanshan; Cheng Xinbin; Zhu Jingtao; Huang Qiushi; Zhang Zhong; Chen Lingyan

2011-01-01

Design, fabrication and characterization of aperiodic tungsten/carbon (W/C) multi-layer mirror were studied. W/C multi-layer was designed as a broad-angle reflective supermirror for Cu-Kα line (λ = 0.154 nm) in the grazing incident angular range (0.9-1.1 deg.) using simulated annealing algorithm. To deposit the W/C depth-graded multi-layer mirror accurately, we introduce an effective layer growth rate as a function of layer thickness. This method greatly improves the reflectivity curve compared to the conventional multi-layer mirror prepared with constant growth rate. The deposited multi-layer mirror exhibits an average reflectivity of 19% over the grazing incident angle range of 0.88-1.08 deg. which mainly coincides with the designed value. Furthermore, the physical mechanisms were discussed and the re-sputtering process of light-atom layers is accounted for the modification of layer thicknesses which leads to the effective growth rates. Using this calibration method, the aperiodic multi-layer mirrors can be better fabricated for X-ray optics.

Atlanta Rail Yard Study: Evaluation of local-scale air pollution trends using stationary and mobile monitoring

Science.gov (United States)

Intermodal rail yards are important nodes in the freight transportation network, where freight is organized and moved from one mode of transport to another, critical equipment is serviced, and freight is routed to its next destination. Rail yard environments are also areas with ...

Modelling the Dynamic Impacts of High Speed Rail Operation on Regional Public Transport—From the Perspective of Energy Economy

Directory of Open Access Journals (Sweden)

Ching-Chih Chou

2018-05-01

Full Text Available While the introduction of a high speed rail (HSR provides passengers with another more environmentally friendly, convenient, and time-saving transport option, it also disrupts the existing passenger transport market. This study adopts time series analysis to model the dynamic competition in a regional passenger transport market when an HSR is introduced. The analyses include examining the long-run equilibrium and causal relationships, and the short-run causality and dynamic relationships between transport modes. In addition, based on the model we conduct impulse response tests and variance decomposition tests to further interpret the interactions between two transport modes. An empirical study is carried out, and the findings indicate that the HSR has a negative impact on conventional rail and air transport in the long-run. In the short-run dynamics, the air passenger transport volume could be regarded as a good predictor of HSR passenger volume. In turn, the HSR passenger volume could be used to predict conventional rail transport volume. The operations of HSR and conventional rail are complementary in the short term. From the short-run market viewpoint, the HSR and conventional rail meet different kinds of passenger demand. Therefore, a previous increased passenger volume for the HSR implies an overall increasing demand for regional transport. Consequently, the past increased HSR passenger volume could be used to predict the growth of conventional rail transport. Through the impulse response test, we can further track the responses of the three transport modes to the shocks from themselves and each other.

A simple theoretical model of heat and moisture transport in multi-layer garments in cool ambient air.

Science.gov (United States)

Wissler, Eugene H; Havenith, George

2009-03-01

Overall resistances for heat and vapor transport in a multilayer garment depend on the properties of individual layers and the thickness of any air space between layers. Under uncomplicated, steady-state conditions, thermal and mass fluxes are uniform within the garment, and the rate of transport is simply computed as the overall temperature or water concentration difference divided by the appropriate resistance. However, that simple computation is not valid under cool ambient conditions when the vapor permeability of the garment is low, and condensation occurs within the garment. Several recent studies have measured heat and vapor transport when condensation occurs within the garment (Richards et al. in Report on Project ThermProject, Contract No. G6RD-CT-2002-00846, 2002; Havenith et al. in J Appl Physiol 104:142-149, 2008). In addition to measuring cooling rates for ensembles when the skin was either wet or dry, both studies employed a flat-plate apparatus to measure resistances of individual layers. Those data provide information required to define the properties of an ensemble in terms of its individual layers. We have extended the work of previous investigators by developing a rather simple technique for analyzing heat and water vapor transport when condensation occurs within a garment. Computed results agree well with experimental results reported by Richards et al. (Report on Project ThermProject, Contract No. G6RD-CT-2002-00846, 2002) and Havenith et al. (J Appl Physiol 104:142-149, 2008). We discuss application of the method to human subjects for whom the rate of sweat secretion, instead of the partial pressure of water on the skin, is specified. Analysis of a more complicated five-layer system studied by Yoo and Kim (Text Res J 78:189-197, 2008) required an iterative computation based on principles defined in this paper.

Can urban rail transit curb automobile energy consumption?

International Nuclear Information System (INIS)

Lin, Boqiang; Du, Zhili

2017-01-01

With the rapid development of China's economy and the speed of urbanization, China's automobile sector has experienced rapid development. The rapid development of the automobile sector has increased energy consumption. According to the results of this paper, automobile energy consumption accounted for about 10.73% of total energy consumption in China in 2015, about 3.6 times the proportion a decade ago. With the deterioration of urban traffic conditions, relying on expanding the amount of vehicles and city road network cannot solve the problem. Urban rail transit is energy-saving and less-polluting, uses less space, has large capacity, and secure. Urban rail transit, according to the principle of sustainable development, is a green transportation system and should be especially adopted for large and medium-sized cities. The paper uses the binary choice model (Probit and Logit) to analyze the main factors influencing the development of rail transit in Chinese cities, and whether automobile energy consumption is the reason for the construction of urban rail transit. Secondly, we analyze the influence of urban rail transit on automobile energy consumption using DID model. The results indicate that the construction of urban rail traffic can restrain automobile energy consumption significantly, with continuous impact in the second year. - Highlights: • Investigate the main factors influencing the building of rail transit for Chinese cities. • Analyze the influence of urban rail transit on automobile energy consumption by DID model. • The results indicate that the construction of urban rail traffic can restrain automobile energy consumption significantly.

A Big Data Analysis Approach for Rail Failure Risk Assessment.

Science.gov (United States)

Jamshidi, Ali; Faghih-Roohi, Shahrzad; Hajizadeh, Siamak; Núñez, Alfredo; Babuska, Robert; Dollevoet, Rolf; Li, Zili; De Schutter, Bart

2017-08-01

Railway infrastructure monitoring is a vital task to ensure rail transportation safety. A rail failure could result in not only a considerable impact on train delays and maintenance costs, but also on safety of passengers. In this article, the aim is to assess the risk of a rail failure by analyzing a type of rail surface defect called squats that are detected automatically among the huge number of records from video cameras. We propose an image processing approach for automatic detection of squats, especially severe types that are prone to rail breaks. We measure the visual length of the squats and use them to model the failure risk. For the assessment of the rail failure risk, we estimate the probability of rail failure based on the growth of squats. Moreover, we perform severity and crack growth analyses to consider the impact of rail traffic loads on defects in three different growth scenarios. The failure risk estimations are provided for several samples of squats with different crack growth lengths on a busy rail track of the Dutch railway network. The results illustrate the practicality and efficiency of the proposed approach. © 2017 The Authors Risk Analysis published by Wiley Periodicals, Inc. on behalf of Society for Risk Analysis.

Review on Malaysian Rail Transit Operation and Management System: Issues and Solution in Integration

Science.gov (United States)

Masirin, Mohd Idrus Mohd; Salin, Aminah Mohd; Zainorabidin, Adnan; Martin, David; Samsuddin, Norshakina

2017-08-01

In any context, operation and management of transportation systems are key issues which may affect both life quality and economic development. In large urban agglomerations, an efficient public transportation system may help abate the negative externalities of private car use such as congestion, air and noise pollution, accident and fuel consumption, without excessively penalizing user travel times or zone accessibility. Thus, this study is conducted to appraise the Malaysian rural rail transit operation and management system, which are considered important as there are many issues and solution in integration of the services that need to be tackled more conscientiously. The purpose of this paper is to describe some of the most important issues on integration of services and rail transit system in Malaysian and how to solve or reduce these problems and conflicts. In this paper, it consists of the historical development of rail transit construction in Malaysia. This paper also attempts to identify the important issues related to rail transit services and integration in Malaysian rural rail operation and management system. Comparison is also conducted with other countries such as UK, France, and Japan. Finally, a critical analysis is presented in this paper by looking at the possible application for future Malaysian rail transit operation system and management, especially focusing on enhancing the quality of Malaysian rural rail transit. In conclusion, this paper is expected to successfully review and appraise the existing Malaysian rural rail transit operation and management system pertaining to issues & solution in integration. It is also hoped that reformation or transformation of present service delivery quality of the rail transit operation and management will enable Malaysia to succeed in transforming Malaysian transportation system to greater heights.

Spacer layer effect and microstructure on multi-layer [NdFeB/Nb]n films

International Nuclear Information System (INIS)

Tsai, J.-L.; Yao, Y.-D.; Chin, T.-S.; Kronmueller, H.

2002-01-01

Spacer layer effect on multi-layer [NdFeB/Nb] n films has been investigated from the variation of magnetic properties and microstructure of the films. From a HRTEM cross-section view observation, the average grain size of [NdFeB/Nb] n multi-layers was controlled by both annealing temperature and thickness of NdFeB layer. Selected area diffraction pattern indicated that the structure of Nb spacer layer was amorphous. The grain size and coercivity of [NdFeB x /Nb] n films change from 50 nm and 16.7 kOe to 167 nm and 9 kOe for films with x=40 nm, n=10 and x=200 nm, n=2, respectively

SELECTED MODELS OF RAIL MARKETS IN THE CONTEXT OF LIBERALIZATION OF THE RAIL MARKET IN EUROPE

Directory of Open Access Journals (Sweden)

Krystian Pietrzak

2016-09-01

Full Text Available In the paper author has made an attempt at presenting problems of the operation of European railway transport market against the background of changes taking place in the European Union transport market. These changes are the result of processes aimed at liberalizing the market. In addition, this article defines the conditions of reforms in the Eu-ropean rail market by highlighting various models of its functioning.

Experimental Study of Weepage in Multi-layer Glass Reinforced Piping

KAUST Repository

Al Sinan, Hussain

2014-05-01

Glass Reinforced Polymer pipes, commonly used in water transport applications, are prone to long term weepage. Weepage is defined as the transfer of fluid through the pipe and is considered a functional failure. An experimental investigation of weepage in multi-layered GRP pipes was carried out in two parts aiming to understand the phenomenon to help enhance the weepage resistance of manufactured pipes. First, liner surface profilometry investigation was carried out to identify microscopic features that might serve in initiating weepage. Second, MRI and x-ray tomography and SEM imaging of pipe samples aged with water and dye penetrant was carried out to capture weepage development through the pipe thickness. Diffusion through liner fiber/resin interface, propagation in the direction of poorly wetted hoop fibers and transverse cracks were found to be the likely causes of accelerating weepage in the samples. Fiber rich zones in the liner were considered weak spots that water can use for fast penetration of the liner. Finally, polyester netting used to hold core layer was found to help in water accumulation and transport through the pipe increasing the chances of failure.

Experimental Study of Weepage in Multi-layer Glass Reinforced Piping

KAUST Repository

Al Sinan, Hussain

2014-01-01

Glass Reinforced Polymer pipes, commonly used in water transport applications, are prone to long term weepage. Weepage is defined as the transfer of fluid through the pipe and is considered a functional failure. An experimental investigation of weepage in multi-layered GRP pipes was carried out in two parts aiming to understand the phenomenon to help enhance the weepage resistance of manufactured pipes. First, liner surface profilometry investigation was carried out to identify microscopic features that might serve in initiating weepage. Second, MRI and x-ray tomography and SEM imaging of pipe samples aged with water and dye penetrant was carried out to capture weepage development through the pipe thickness. Diffusion through liner fiber/resin interface, propagation in the direction of poorly wetted hoop fibers and transverse cracks were found to be the likely causes of accelerating weepage in the samples. Fiber rich zones in the liner were considered weak spots that water can use for fast penetration of the liner. Finally, polyester netting used to hold core layer was found to help in water accumulation and transport through the pipe increasing the chances of failure.

Optimisation of multi-layer rotationally moulded foamed structures

Science.gov (United States)

Pritchard, A. J.; McCourt, M. P.; Kearns, M. P.; Martin, P. J.; Cunningham, E.

2018-05-01

Multi-layer skin-foam and skin-foam-skin sandwich constructions are of increasing interest in the rotational moulding process for two reasons. Firstly, multi-layer constructions can improve the thermal insulation properties of a part. Secondly, foamed polyethylene sandwiched between solid polyethylene skins can increase the mechanical properties of rotationally moulded structural components, in particular increasing flexural properties and impact strength (IS). The processing of multiple layers of polyethylene and polyethylene foam presents unique challenges such as the control of chemical blowing agent decomposition temperature, and the optimisation of cooling rates to prevent destruction of the foam core; therefore, precise temperature control is paramount to success. Long cooling cycle times are associated with the creation of multi-layer foam parts due to their insulative nature; consequently, often making the costs of production prohibitive. Devices such as Rotocooler®, a rapid internal mould water spray cooling system, have been shown to have the potential to significantly decrease cooling times in rotational moulding. It is essential to monitor and control such devices to minimise the warpage associated with the rapid cooling of a moulding from only one side. The work presented here demonstrates the use of threaded thermocouples to monitor the polymer melt in multi-layer sandwich constructions, in order to analyse the cooling cycle of multi-layer foamed structures. A series of polyethylene skin-foam test mouldings were produced, and the effect of cooling medium on foam characteristics, mechanical properties, and process cycle time were investigated. Cooling cycle time reductions of 45%, 26%, and 29% were found for increasing (1%, 2%, and 3%) chemical blowing agent (CBA) amount when using internal water cooling technology from ˜123°C compared with forced air cooling (FAC). Subsequently, a reduction of IS for the same skin-foam parts was found to be 1%, 4

Could Expanded Freight Rail Reduce Air Pollution from Trucks?

Science.gov (United States)

Bickford, E. E.; Holloway, T.; Johnston, M.

2010-12-01

Cars, trucks and trains are a significant source of emissions that impact both climate and air quality on regional to global scales. Diesel vehicles, most used for freight transport, account for 42% of on-road nitrogen oxide emissions, 58% of on-road fine particulate emissions, and 21% of on-road carbon dioxide emissions. With freight tonnage projected to increase 28% by 2018, and freight trucks the fastest growing source of transportation emissions, we evaluate the potential for increased rail capacity to reduce the environmental impacts of trucks. Most widely available mobile source emissions inventories contain insufficient spatial detail to quantify realistic emission scenario options, and none to date have been linked with commodity flow information in a manner appropriate to consider the true potential of rail substitution. To support a truck-to-rail analysis, and other policy assessments requiring roadway-by-roadway analysis, we have developed a freight emissions inventory for the Upper Midwest based on the Federal Highway Administration’s Freight Analysis Framework version 2.2 and the Environmental Protection Agency’s on-road emissions model, Mobile6.2. Using a Geographical Information System (GIS), we developed emissions scenarios for truck-to-rail modal shifts where 95% of freight tonnage on trips longer than 400 miles is shifted off of trucks and onto railways. Scenarios will be analyzed with the Community Multiscale Air Quality (CMAQ) regional model to assess air quality impacts of associated changes. By using well-respected transportation data and realistic assumptions, results from this study have the potential to inform decisions on transportation sustainability, carbon management, public health, and air quality.

49 CFR 214.525 - Towing with on-track roadway maintenance machines or hi-rail vehicles.

Science.gov (United States)

2010-10-01

... or hi-rail vehicles. 214.525 Section 214.525 Transportation Other Regulations Relating to... SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.525 Towing with on-track roadway maintenance machines or hi-rail vehicles. (a) When used to tow pushcars or other maintenance-of-way equipment...

Characterization of transport phenomena in porous transport layers using X-ray microtomography

Science.gov (United States)

Hasanpour, S.; Hoorfar, M.; Phillion, A. B.

2017-06-01

Among different methods available for estimating the transport properties of porous transport layers (PTLs) of polymer electrolyte membrane fuel cells, X-ray micro computed tomography (X-μCT) imaging in combination with image-based numerical simulation has been recognized as a viable tool. In this study, four commercially-available single-layer and dual-layer PTLs are analyzed using this method in order to compare and contrast transport properties between different PTLs, as well as the variability within a single sheet. Complete transport property datasets are created for each PTL. The simulation predictions indicate that PTLs with high porosity show considerable variability in permeability and effective diffusivity, while PTLs with low porosity do not. Furthermore, it is seen that the Tomadakis-Sotirchos (TS) analytical expressions for porous media match the image-based simulations when porosity is relatively low but predict higher permeability and effective diffusivity for porosity values greater than 80%. Finally, the simulations show that cracks within MPL of dual-layer PTLs have a significant effect on the overall permeability and effective diffusivity of the PTLs. This must be considered when estimating the transport properties of dual-layer PTLs. These findings can be used to improve macro-scale models of product and reactant transport within fuel cells, and ultimately, fuel cell efficiency.

Numerical modeling of solute transport in deformable unsaturated layered soil

Directory of Open Access Journals (Sweden)

Sheng Wu

2017-07-01

Full Text Available The effect of soil stratification was studied through numerical investigation based on the coupled model of solute transport in deformable unsaturated soil. The theoretical model implied two-way coupled excess pore pressure and soil deformation based on Biot's consolidation theory as well as a one-way coupled volatile pollutant concentration field developed from the advection-diffusion theory. Embedded in the model, the degree of saturation, fluid compressibility, self-weight of the soil matrix, porosity variance, longitudinal dispersion, and linear sorption were computed. Based on simulation results of a proposed three-layer landfill model using the finite element method, the multi-layer effects are discussed with regard to the hydraulic conductivity, shear modulus, degree of saturation, molecular diffusion coefficient, and thickness of each layer. Generally speaking, contaminants spread faster in a stratified field with a soft and highly permeable top layer; soil parameters of the top layer are more critical than the lower layers but controlling soil thicknesses will alter the results. This numerical investigation showed noticeable impacts of stratified soil properties on solute migration results, demonstrating the importance of correctly modeling layered soil instead of simply assuming the averaged properties across the soil profile.

Corrosion behaviour in saline environments of single-layer titanium and aluminium coatings, and of Ti/Al alternated multi-layers elaborated by a multi-beam PVD technique

International Nuclear Information System (INIS)

Merati, Abdenacer

1994-01-01

This research thesis reports the characterization of anti-corrosion titanium and aluminium coatings deposited on a 35CD4 steel under the form of mono-metallic layers or alternated Ti/Al multi-layers, and obtained by a multibeam PVD technique. The influence of different parameters is studied: single-layer thickness (5, 15 or 30 micro-metres), multi-layer distribution (5 to 6) and substrate (smooth or threaded). Layer nature and microstructure are studied by optical microscopy and scanning electron microscopy (SEM), as well as corrosion toughness in aqueous saline environments. Coated threaded samples have been studied after tightening tests. It appears that titanium layers are denser and more uniform than aluminium layers, and that multi-layer coatings provide a better protection than single-layer coatings. The best behaviour is obtained when titanium is in contact with steel, and aluminium is the outer layer in contact with the corroding environment [fr

Features of formation of car-traffic in a regional transportation system in conditions the multi-agents organization of a railway transportation

Directory of Open Access Journals (Sweden)

Aleksandr Leonidovich Kazakov

2011-09-01

Full Text Available As a result of structural reform of Russian railways, a host of agents that provide customers with loading resources, especially wagons for transport by railway. These processes reduce in efficiency of the car fleet, increasing transportation costs, shortage of cars for many customers, an increase of empty runs and, as a result, a depletion of a number of sections of the network carrying capacity at a reduced total volume of rail traffic. The article describes the reasons for this situation due to the mismatch occurred heterogeneity of rolling stock to existing planning conditions and tariffs. It is also shown that the inefficiency of decentralized car fleet contributes to the predominance of tree-type network, and the importance of this factor in the new environment has increased substantially. To ensure the efficient operation of rail transport as a systemic industry, providing mass-haul transport, it is proposed for integration into a regional logistics. Freight terminals regional logistics transportation and distribution system (RLTRS is appropriate to create on the basis of major freight railway stations. Thus, the adaptation of planning car traffic volume and train formation to modern standards, the establishment of tariff incentives and long-term changes in network configuration are considered as a prerequisite for the transformation of local transport and technological systems on the network of Russian railways into the integrated transport and logistics systems.

78 FR 24803 - Hilco SP Rail, LLC-Acquisition and Operation Exemption-RG Steel Railroad Holding, LLC

Science.gov (United States)

2013-04-26

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35734] Hilco SP Rail, LLC--Acquisition and Operation Exemption--RG Steel Railroad Holding, LLC Hilco SP Rail, LLC (Hilco), a noncarrier... Holding, LLC, and operate as a common carrier over an approximately 12-mile line of railroad in Sparrows...

49 CFR 214.521 - Flagging equipment for on-track roadway maintenance machines and hi-rail vehicles.

Science.gov (United States)

2010-10-01

... maintenance machines and hi-rail vehicles. 214.521 Section 214.521 Transportation Other Regulations Relating... WORKPLACE SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.521 Flagging equipment for on-track roadway maintenance machines and hi-rail vehicles. Each on-track roadway maintenance machine...

Plasma treatment of crane rails

Directory of Open Access Journals (Sweden)

Владислав Олександрович Мазур

2016-07-01

Full Text Available Crane operation results in wear and tear of rails and crane wheels. Renovation and efficiency of these details is therefore relevant. Modern technologies of wheels and rails restoration use surfacing or high-frequency currents treatment. Surface treatment with highly concentrated streams of energy- with a laser beam, plasma jet- is a promising direction.. It is proposed to increase the efficiency of crane rails by means of surface plasma treatment. The modes of treatment have been chosen.. Modelling of plasma jet thermal impact on a solid body of complex shape has been made. Plasma hardening regimes that meet the requirements of production have been defined. Structural transformation of the material in the crane rails on plasma treatment has been investigated. It has been concluded that for carbon and low alloy crane steels the plasma exposure zone is characterized by a high degree of hardened structure dispersion and higher hardness as compared to the hardness after high-frequency quenching. As this takes place phase transformations are both shift (in the upper zone of plasma influence and fluctuation (in the lower zone of the plasma. With high-speed plasma heating granular or lamellar pearlite mainly transforms into austenite. The level of service characteristics of hardened steel, which is achieved in this case is determined by the kinetics and completeness of pearlite → austenite transformation. For carbon and low alloy rail steels plasma hardening can replace bulk hardening, hardening by high-frequency currents, or surfacing. The modes for plasma treatment which make it possible to obtain a surface layer with a certain service characteristics have been defined

High-Speed Rail and Local Land Development : Case Studies in London and Las Vegas

Science.gov (United States)

2017-11-01

The efficacy of a high-speed rail system depends, in part, upon locating rail stations close to urban centers and integrating them into broader transportation networks and the urban realm. In addition, through economies of agglomeration, successful h...

Mathematical model of optimal empty rail car distribution at railway transport nodes

Directory of Open Access Journals (Sweden)

Aleksandr RAKHMANGULOV

2014-09-01

Full Text Available At present there are two trends in the market of rail freight transportation in Russia: freight owners put forward higher demands to the transportation quality (promptness of delivery in an effort to reduce storage costs by means of reducing the size of freight shipment; the structure of railcar traffic volume of the railways of Russia is getting more complex due to the reduction of the average shipment size and due to the transfer of railcar fleet ownership to a large number of operating companies. These trends significantly complicate operational management supervision of railway stations and transport nodes. Application of typical data from the information system about the railcar location at the transportation node is not enough for the dispatchers to make the best decision concerning the car traffic management. The dispatcher traffic control service needs some software-based models of efficient railcar distribution. The article is concerned with the description and development of the mathematical model of empty railcar distribution for loading at the railway transport node; this model will take into account the requirements of railcar owners in terms of their cars application, the operating work level of railroad stations of the transportation node and the possibility of adding the groups of empty railcars to the transfer trains, clean-up trains and industrial railway trains operating on a tight schedule. The developed model and the software package were implemented in the information system of the industrial railway of the major metallurgical enterprise - OJSC «Magnitogorsk Metallurgical Works», which processes up to two thousand of railcars belonging to different owners. This model made it possible to reduce the labour intensity of dispatcher operation planning the empty railcar distribution for loading and reduce the total time the railcars spend in the enterprise railway system.

From Rail-Oriented to Automobile-Oriented Urban Development and Back. 100 Years of Paradigm Change and Transport Policy in Berlin

Directory of Open Access Journals (Sweden)

Friedemann Kunst

2016-10-01

Full Text Available Transport and its side effects are major problems in rapidly growing cities. Car traffic dominates these cities and pollutes the environment without being able to sufficiently secure the mobility of the urban population and goods. A paradigm shift in urban and transport policy will be necessary to change this situation. In spite of its different development dynamics, Berlin is an interesting example to discuss development strategies for rapidly growing cities because in the course of more than 100 years, a twofold paradigm shift has occurred in the city both conceptually and practically:  Berlin has shifted from a city dominated by rail traffic  to an automobile-oriented city,  and has then gradually transformed back into a city in which  an intertwined system of public and non-motorized individual means of transport secures the mobility of the urban population. The interdependencies on the conceptual level between urban planning and transport policies as well as on a practical level between urban structures and transport systems can be studied using the example of Berlin. Experiences with the implementation of automobile-oriented planning and the special conditions in the first decade after reunification led to protests, reflection, and a revision of the transport policy. A strategically designed process of integrated planning has brought about a trend reversal, and steered the development of transport in the direction of clearly formulated sustainability-oriented objectives. In this process, the reintegration of transport and spatial planning and a reorganization of institutional structures at the administrative level was of particular importance. Compact, rail-oriented settlement structures like in the metropolitan region of Berlin make it easier to dispense with automobiles than sprawled structures. The residual role that qualitatively improved automobiles will take in the cities of the future will have to be determined by research and

77 FR 49854 - Tier 1 Environmental Impact Statement for the Oregon Portion of the Pacific Northwest Rail...

Science.gov (United States)

2012-08-17

... represents other transportation modes such as auto, air travel, intercity bus, and existing rail and the... well as making decisions regarding the level of intercity passenger rail service provided in the... growth of 139% between 2000 and 2008. Current intercity passenger rail service in Oregon includes two...

77 FR 2077 - Intent To Request Renewal From OMB of One Current Public Collection of Information: Rail...

Science.gov (United States)

2012-01-13

... carriers, including each carrier operating light rail or heavy rail transit service on track that is part of the general railroad system of transportation and rail transit systems. Also, these persons are... any threat information. In addition, freight railroad carriers and the affected shippers and receivers...

A symmetrical rail accelerator

International Nuclear Information System (INIS)

Igenbergs, E.

1991-01-01

This paper reports on the symmetrical rail accelerator that has four rails, which are arranged symmetrically around the bore. The opposite rails have the same polarity and the adjacent rails the opposite polarity. In this configuration the radial force acting upon the individual rails is significantly smaller than in a conventional 2-rail configuration and a plasma armature is focussed towards the axis of the barrel. Experimental results indicate a higher efficiency compared to a conventional rail accelerator

Test facilities for radioactive materials transport packages (Transportation Technology Center Inc., Pueblo, Colorado, USA)

International Nuclear Information System (INIS)

Conlon, P.C.L.

2001-01-01

Transportation Technology Center, Inc. is capable of conducting tests on rail vehicle systems designed for transporting radioactive materials including low level waste debris, transuranic waste, and spent nuclear fuel and high level waste. Services include rail vehicle dynamics modelling, on-track performance testing, full scale structural fatigue testing, rail vehicle impact tests, engineering design and technology consulting, and emergency response training. (author)

Intermodal transportation of spent fuel

International Nuclear Information System (INIS)

Elder, H.K.

1983-09-01

Concepts for transportation of spent fuel in rail casks from nuclear power plant sites with no rail service are under consideration by the US Department of Energy in the Commercial Spent Fuel Management program at the Pacific Northwest Laboratory. This report identifies and evaluates three alternative systems for intermodal transfer of spent fuel: heavy-haul truck to rail, barge to rail, and barge to heavy-haul truck. This report concludes that, with some modifications and provisions for new equipment, existing rail and marine systems can provide a transportation base for the intermodal transfer of spent fuel to federal interim storage facilities. Some needed land transportation support and loading and unloading equipment does not currently exist. There are insufficient shipping casks available at this time, but the industrial capability to meet projected needs appears adequate

Stationary Charging Station Design for Sustainable Urban Rail Systems: A Case Study at Zhuzhou Electric Locomotive Co., China

OpenAIRE

Heng Li; Jun Peng; Weirong Liu; Zhiwu Huang

2015-01-01

In 2014, more than 43 cities in China were racing to construct their urban rail systems (including metro and light rail systems), recognizing that an urban rail system will be a good solution to the tough problems that they are faced with, including traffic congestion and PM2.5 air pollution. On 22 August 2012, the first electric double-layer capacitor (EDLC) energy storage-type rail vehicle in the world was unveiled at Zhuzhou Electric Locomotive Co., China. The EDLC rail system has been con...

Development and application of resilient wheels in urban rail transit vehicle

Directory of Open Access Journals (Sweden)

Juan WEN

Full Text Available Urban rail transit vehicles have been more and more attractive to people as a kind of fast, comfortable, energy-saving, environmental protection and safe transportation. But because of the vehicle noise and vibration, urban rail vehicles also face severe challenges. The research of resilient wheels has been continuously developed and improved. Based on the review of development background and structure sorts of resilient wheels, the advantages of resilient wheels are described, and the research status of noise and vibration reducing, infinite element strength analysis, vehicle dynamic analysis and the wheel-rail wear of resilient wheels are discussed. Taking the low-floor LRVs (light rail vehicles in domestic and overseas as example, the development and application of the resilient wheels in city rail transit is described, and the application prospects of the resilient wheels in LRVs in domestic and the future research direction of elastic wheel are discussed.

Multi-area layered multicast scheme for MPLS networks

Science.gov (United States)

Ma, Yajie; Yang, Zongkai; Wang, Yuming; Chen, Jingwen

2005-02-01

Multi-protocol label switching (MPLS) is multiprotocols both at layer 2 and layer 3. It is suggested to overcome the shortcomings of performing complex longest prefix matching in layer 3 routing by using short, fixed length labels. The MPLS community has put more effort into the label switching of unicast IP traffic, but less in the MPLS multicast mechanism. The reasons are the higher label consumption, the dynamical mapping of L3 multicast tree to L2 LSPs and the 20-bit shim header which is much fewer than the IPv4 IP header. On the other hand, heterogeneity of node capability degrades total performance of a multicast group. In order to achieve the scalability as well as the heterogeneity in MPLS networks, a novel scheme of MPLS-based Multi-area Layered Multicast Scheme (MALM) is proposed. Unlike the existing schemes which focus on aggregating the multicast stream, we construct the multicast tree based on the virtual topology aggregation. The MPLS area is divided into different sub-areas to form the hierarchical virtual topology and the multicast group is reconstructed into multiple layers according to the node capability. At the same time, the label stack is used to save the label space. For stability of the MALM protocol, a multi-layer protection scheme is also discussed. The experiment results show that the proposed scheme saves label space and decrease the Multicast Forwarding Table in much degree.

Nevada Transportation Options Study

International Nuclear Information System (INIS)

P. GEHNER; E.M. WEAVER; L. FOSSUM

2006-01-01

This study performs a cost and schedule analysis of three Nevada Transportation options that support waste receipt at the repository. Based on the U.S. Department of Energy preference for rail transportation in Nevada (given in the Final Environmental Impact Statement), it has been assumed that a branch rail line would be constructed to support waste receipt at the repository. However, due to potential funding constraints, it is uncertain when rail will be available. The three Nevada Transportation options have been developed to meet a varying degree of requirements for transportation and to provide cost variations used in meeting the funding constraints given in the Technical Direction Letter guidelines for this study. The options include combinations of legal-weight truck, heavy-haul truck, and rail. Option 1 uses a branch rail line that would support initial waste receipt at the repository in 2010. Rail transportation would be the primary mode, supplemented by legal weight trucks. This option provides the highest level of confidence in cost and schedule, lowest public visibility, greatest public acceptability, lowest public dose, and is the recommended option for support of waste receipt. The completion of rail by 2010 will require spending approximately $800 million prior to 2010. Option 2 uses a phased rail approach to address a constrained funding scenario. To meet funding constraints, Option 2 uses a phased approach to delay high cost activities (final design and construction) until after initial waste receipt in 2010. By doing this, approximately 95 percent of the cost associated with completion of a branch rail line is deferred until after 2010. To support waste receipt until a branch rail line is constructed in Nevada, additional legal-weight truck shipments and heavy-haul truck shipments (on a limited basis for naval spent nuclear fuel) would be used to meet the same initial waste receipt rates as in Option 1. Use of heavy-haul shipments in the absence

Electrohydrodynamic direct—writing of conductor—insulator-conductor multi-layer interconnection

International Nuclear Information System (INIS)

Zheng Gao-Feng; Pei Yan-Bo; Wang Xiang; Zheng Jian-Yi; Sun Dao-Heng

2014-01-01

A multi-layer interconnection structure is a basic component of electronic devices, and printing of the multi-layer interconnection structure is the key process in printed electronics. In this work, electrohydrodynamic direct-writing (EDW) is utilized to print the conductor—insulator—conductor multi-layer interconnection structure. Silver ink is chosen to print the conductor pattern, and a polyvinylpyrrolidone (PVP) solution is utilized to fabricate the insulator layer between the bottom and top conductor patterns. The influences of EDW process parameters on the line width of the printed conductor and insulator patterns are studied systematically. The obtained results show that the line width of the printed structure increases with the increase of the flow rate, but decreases with the increase of applied voltage and PVP content in the solution. The average resistivity values of the bottom and top silver conductor tracks are determined to be 1.34 × 10 −7 Ω·m and 1.39 × 10 −7 Ω·m, respectively. The printed PVP layer between the two conductor tracks is well insulated, which can meet the insulation requirement of the electronic devices. This study offers an alternative, fast, and cost-effective method of fabricating conductor—insulator—conductor multi-layer interconnections in the electronic industry

Electrically Tunable and Negative Schottky Barriers in Multi-layered Graphene/MoS2 Heterostructured Transistors

Science.gov (United States)

Qiu, Dongri; Kim, Eun Kyu

2015-09-01

We fabricated multi-layered graphene/MoS2 heterostructured devices by positioning mechanically exfoliated bulk graphite and single-crystalline 2H-MoS2 onto Au metal pads on a SiO2/Si substrate via a contamination-free dry transfer technique. We also studied the electrical transport properties of Au/MoS2 junction devices for systematic comparison. A previous work has demonstrated the existence of a positive Schottky barrier height (SBH) in the metal/MoS2 system. However, analysis of the SBH indicates that the contacts of the multi-layered graphene/MoS2 have tunable negative barriers in the range of 300 to -46 meV as a function of gate voltage. It is hypothesized that this tunable SBH is responsible for the modulation of the work function of the thick graphene in these devices. Despite the large number of graphene layers, it is possible to form ohmic contacts, which will provide new opportunities for the engineering of highly efficient contacts in flexible electronics and photonics.

Electrically Tunable and Negative Schottky Barriers in Multi-layered Graphene/MoS2 Heterostructured Transistors.

Science.gov (United States)

Qiu, Dongri; Kim, Eun Kyu

2015-09-03

We fabricated multi-layered graphene/MoS2 heterostructured devices by positioning mechanically exfoliated bulk graphite and single-crystalline 2H-MoS2 onto Au metal pads on a SiO2/Si substrate via a contamination-free dry transfer technique. We also studied the electrical transport properties of Au/MoS2 junction devices for systematic comparison. A previous work has demonstrated the existence of a positive Schottky barrier height (SBH) in the metal/MoS2 system. However, analysis of the SBH indicates that the contacts of the multi-layered graphene/MoS2 have tunable negative barriers in the range of 300 to -46 meV as a function of gate voltage. It is hypothesized that this tunable SBH is responsible for the modulation of the work function of the thick graphene in these devices. Despite the large number of graphene layers, it is possible to form ohmic contacts, which will provide new opportunities for the engineering of highly efficient contacts in flexible electronics and photonics.

Calculation studies of a multi-layer decoupler system for a decoupled hydrogen moderator

International Nuclear Information System (INIS)

Ooi, M.; Kiyanagi, Y.

2001-01-01

We proposed a multi-layer decoupler as a method to improve pulse characteristics of emitted neutrons from a decoupled hydrogen moderator. Pulse shapes from a moderator with the multi layer-decoupler were compared with those with a traditional single layer decoupler. It was found that the multi-layer decoupler system gave better pulse characteristic with less decrease of peak intensity. (author)

Methods for producing thin film charge selective transport layers

Science.gov (United States)

Hammond, Scott Ryan; Olson, Dana C.; van Hest, Marinus Franciscus Antonius Maria

2018-01-02

Methods for producing thin film charge selective transport layers are provided. In one embodiment, a method for forming a thin film charge selective transport layer comprises: providing a precursor solution comprising a metal containing reactive precursor material dissolved into a complexing solvent; depositing the precursor solution onto a surface of a substrate to form a film; and forming a charge selective transport layer on the substrate by annealing the film.

System and prospects of China's intercity rail transit technology

Science.gov (United States)

Gong, Ming

2018-06-01

City clusters and metropolitan areas in China are flourishing in the midst of the deepening urbanization in the country, thereby resulting in the emergence of intercity rail transit. Intercity railways connect mainline and urban railways for an integrated regional transportation system that underpins and leads the development of city clusters and metropolitan areas. This study explores the development mode and service characteristics of intercity rail transit, as well as proposes overviews on this system and prospects of its future technology in China.

High energy PIXE: A tool to characterize multi-layer thick samples

Science.gov (United States)

Subercaze, A.; Koumeir, C.; Métivier, V.; Servagent, N.; Guertin, A.; Haddad, F.

2018-02-01

High energy PIXE is a useful and non-destructive tool to characterize multi-layer thick samples such as cultural heritage objects. In a previous work, we demonstrated the possibility to perform quantitative analysis of simple multi-layer samples using high energy PIXE, without any assumption on their composition. In this work an in-depth study of the parameters involved in the method previously published is proposed. Its extension to more complex samples with a repeated layer is also presented. Experiments have been performed at the ARRONAX cyclotron using 68 MeV protons. The thicknesses and sequences of a multi-layer sample including two different layers of the same element have been determined. Performances and limits of this method are presented and discussed.

Application of HLA in the Optimization of Rail Transport

NARCIS (Netherlands)

Berg, T.W. van den; Jansen, R.E.J.; Middelkoop, D.

2008-01-01

The Dutch rail infrastructure manager – Prorail – utilizes simulation to perform research in a number of areas of railtransport.One area that is of particular interest is that of the analysis of Dynamic Traffic Management (DTM) of trains. The aim of DTM is to manage plan/timetable deviations from

Multi-criteria appraisal of multi-modal urban public transport systems

NARCIS (Netherlands)

Keyvan Ekbatani, M.; Cats, O.

2015-01-01

This study proposes a multi-criteria decision making (MCDM) modelling framework for the appraisal of multi-modal urban public transportation services. MCDM is commonly used to obtain choice alternatives that satisfy a range of performance indicators. The framework embraces both compensatory and

Rails on Windows

CERN Document Server

Hibbs, Curt

2007-01-01

It's no secret that the entire Ruby onRails core team uses OS X as their preferreddevelopment environment. Becauseof this, it is very easy to findauthoritative information on the webabout using Rails on OS X. But the truthis that Windows developers using Railsprobably outnumber those using otherplatforms. A Windows development environmentcan be just as productive asany other platform. This is a guide to developing with Rubyon Rails under Windows. It won't teachyou how to write Ruby on Rails web applications,but it will show you what toolsto use and how to set them up to createa complete Rail

Occupant Volume Integrity Evaluation in Passenger Rail Cars

Science.gov (United States)

2012-02-01

This research, which is intended to enable the growth of high-speed and intercity passenger rail transportation, was sponsored by the Federal Railroad Administration (FRA) Office of Research and Development, as part of the train Occupant Protection r...

Optoelectronic device with nanoparticle embedded hole injection/transport layer

Science.gov (United States)

Wang, Qingwu [Chelmsford, MA; Li, Wenguang [Andover, MA; Jiang, Hua [Methuen, MA

2012-01-03

An optoelectronic device is disclosed that can function as an emitter of optical radiation, such as a light-emitting diode (LED), or as a photovoltaic (PV) device that can be used to convert optical radiation into electrical current, such as a photovoltaic solar cell. The optoelectronic device comprises an anode, a hole injection/transport layer, an active layer, and a cathode, where the hole injection/transport layer includes transparent conductive nanoparticles in a hole transport material.

Singular point analysis during rail deployment into vacuum vessel for ITER blanket maintenance

International Nuclear Information System (INIS)

Kakudate, Satoshi; Shibanuma, Kiyoshi

2007-05-01

Remote maintenance of the ITER blanket composed of about 400 modules in the vessel is required by a maintenance robot due to high gamma radiation of ∼500Gy/h in the vessel. A concept of rail-mounted vehicle manipulator system has been developed to apply to the maintenance of the ITER blanket. The most critical issue of the vehicle manipulator system is the feasibility of the deployment of the articulated rail composed of eight rail links into the donut-shaped vessel without any driving mechanism in the rail. To solve this issue, a new driving mechanism and procedure for the rail deployment has been proposed, taking account of a repeated operation of the multi-rail links deployed in the same kinematical manner. The new driving mechanism, which is deferent from those of a usual 'articulated arm' equipped with actuator in the every joint for movement, is composed of three mechanisms. To assess the feasibility of the kinematics of the articulated rail for rail deployment, a kinematical model composed of three rail links related to a cycle of the repeated operation for rail deployment was considered. The determinant det J' of the Jacobian matrix J' was solved so as to estimate the existence of a singular point of the transformation during rail deployment. As a result, it is found that there is a singular point due to det J'=0. To avoid the singular point of the rail links, a new location of the second driving mechanism and the related rail deployment procedure are proposed. As a result of the rail deployment test based on the new proposal using a full-scale vehicle manipulator system, the respective rail links have been successfully deployed within 6 h less than the target of 8 h in the same manner of the repeated operation under a synchronized cooperation among the three driving mechanisms. It is therefore concluded that the feasibility of the rail deployment of the articulated rail composed of simple structures without any driving mechanism has been demonstrated

Thermoelectric characteristics of Pt-silicide/silicon multi-layer structured p-type silicon

International Nuclear Information System (INIS)

Choi, Wonchul; Jun, Dongseok; Kim, Soojung; Shin, Mincheol; Jang, Moongyu

2015-01-01

Electric and thermoelectric properties of silicide/silicon multi-layer structured devices were investigated with the variation of silicide/silicon heterojunction numbers from 3 to 12 layers. For the fabrication of silicide/silicon multi-layered structure, platinum and silicon layers are repeatedly sputtered on the (100) silicon bulk substrate and rapid thermal annealing is carried out for the silicidation. The manufactured devices show ohmic current–voltage (I–V) characteristics. The Seebeck coefficient of bulk Si is evaluated as 195.8 ± 15.3 μV/K at 300 K, whereas the 12 layered silicide/silicon multi-layer structured device is evaluated as 201.8 ± 9.1 μV/K. As the temperature increases to 400 K, the Seebeck coefficient increases to 237.2 ± 4.7 μV/K and 277.0 ± 1.1 μV/K for bulk and 12 layered devices, respectively. The increase of Seebeck coefficient in multi-layered structure is mainly attributed to the electron filtering effect due to the Schottky barrier at Pt-silicide/silicon interface. At 400 K, the thermal conductivity is reduced by about half of magnitude compared to bulk in multi-layered device which shows the efficient suppression of phonon propagation by using Pt-silicide/silicon hetero-junctions. - Highlights: • Silicide/silicon multi-layer structured is proposed for thermoelectric devices. • Electric and thermoelectric properties with the number of layer are investigated. • An increase of Seebeck coefficient is mainly attributed the Schottky barrier. • Phonon propagation is suppressed with the existence of Schottky barrier. • Thermal conductivity is reduced due to the suppression of phonon propagation

76 FR 8397 - Environmental Impact Statement for the Chicago, IL to St. Louis, MO High Speed Rail Program Corridor

Science.gov (United States)

2011-02-14

... transportation modes, such as auto, air travel, intercity bus, and existing rail, and the physical... regional travel needs through significant improvements to the level and quality of passenger rail service... would divert intercity passenger rail service from the larger populations currently served in the...

Electrodynamic wear of rails in high current density rail gun discharges

International Nuclear Information System (INIS)

Edwards, W.T.; Caldwell, S.G.

1984-01-01

Significant advances in high current, high speed power sources, has in recent years allowed rail guns to produce very high velocity (> 10 km/sec) macroscopic particles (> 1/10 grams). A continuing problem is the structural integrity of the components under these loadings and in particular, the rail wear due to the high current density plasma contacts. In this investigation a small bore rail gun (6x5 mm) was used with a 10.6 kjoule capacitor energy source to examine the modes of rail damage. The rails were constructed of 110 copper base material. These rails were used in an uncoated condition and also with plasma sprayed coatings of W and W/WC. The resulting surface wear was characterized by standard metallurgical techniques and analyzed for the various coatings

Hybrid Multi-Layer Network Control for Emerging Cyber-Infrastructures

Energy Technology Data Exchange (ETDEWEB)

Summerhill, Richard [Internet2, Washington, DC (United States); Lehman, Tom [Univ. of Southern California, Los Angeles, CA (United States). Information Sciences Inst. (ISI); Ghani, Nasir [Univ. of New Mexico, Albuquerque, NM (United States). Dept. of Electrical & Computer Engineering; Boyd, Eric [Univ. Corporation for Advanced Internet Development (UCAID), Washington, DC (United States)

2009-08-14

There were four basic task areas identified for the Hybrid-MLN project. They are: Multi-Layer, Multi-Domain, Control Plane Architecture and Implementation; Heterogeneous DataPlane Testing; Simulation; Project Publications, Reports, and Presentations.

A Practical Model for Inbound Container Distribution Organization in Rail-Water Transhipping Terminal

Directory of Open Access Journals (Sweden)

Jiahao Zhao

2018-01-01

Full Text Available Rail-water transportation is a crucial component of intermodal transportation system. Effective operation of rail-water intermodal transportation requires not only railway network and advanced handling equipment, but also scientific and reasonable transportation organization. In this paper, we first briefly introduced the coordination area and related concepts. Then an inbound container distribution organization model (ICDOM was established taking into account many factors such as transhipping capacity, network capacity, and importance of containers, in order to minimize the total container-hours in the coordination area, which reflects the efficiency of inbound container distribution organization. Additionally, a genetic algorithm (GA was developed and the optimization results were evaluated, which showed that both of the model and the algorithm were effective.

Mechanisms and modeling development of water transport/phase change in catalyst layers of portion exchange membrane fuel cells

Energy Technology Data Exchange (ETDEWEB)

Xiao, Yexiang [Dept. of Thermal Engineering, Tsinghua University Beijing (China)], email: Yexiang.Xiao@energy.lth.se; Yuan, Jinliang; Sunden, Bengt [Dept. of Energy Sciences, Faculty of Engineering, Lund University (Sweden)], email: Jinliang.yuan@energy.lth.se, email: bengt.sunden@energy.lth.se

2011-07-01

Research on proton exchange membrane fuel cells has shown that incorporation of nanosized catalysts can effectively increase active areas and catalyst activity and make a great contribution to development in performance and catalyst utilization. Multiphase transport processes are as significant and complicated as water generation/transfer processes which occur in nano-structured catalyst layers. A review project has been launched aimed at gaining a comprehensive understanding of the mechanisms of water generation or transport phenomena. It covers catalytic reactions and water-phase change within the catalyst layers. The review proceeds in three main stages: Firstly, it characterizes and reconstructs the nano/micro-structured pores and solid-phases; secondly, it emphasises the importance of sensitive and consistent analysis of various water-phase change and transport schemes; and thirdly, it recommends development of microscopic models for multi-phase transport processes in the pores and the solid phases.

Structural analysis of the ITER Divertor toroidal rails

Energy Technology Data Exchange (ETDEWEB)

Viganò, F., E-mail: Fabio.Vigano@LTCalcoli.it [L.T. Calcoli SaS, Piazza Prinetti 26/B, 23807 Merate (Italy); Escourbiac, F.; Gicquel, S.; Komarov, V. [ITER Organization, Route de Vinon sur Verdon, 13115 St. Paul lez Durance (France); Lucca, F. [L.T. Calcoli SaS, Piazza Prinetti 26/B, 23807 Merate (Italy); Merola, M. [ITER Organization, Route de Vinon sur Verdon, 13115 St. Paul lez Durance (France); Ngnitewe, R. [L.T. Calcoli SaS, Piazza Prinetti 26/B, 23807 Merate (Italy)

2013-10-15

The Divertor is one of the most technically challenging components of the ITER machine, which has the main function of extracting the power conducted in the scrape-off layer while maintaining the plasma purity. There are 54 Divertor cassettes installed in the vacuum vessel (VV). Each cassette body (CB) is fastened on the inner and outer concentric Divertor toroidal rails. The comprehensive assessment (in accordance with the Structural Design Criteria for ITER In-vessel Components: ITER SDC-IC) of the Divertor toroidal rails has been performed during design activity based on performing of thermal and stress analyses at operating conditions of neutron stage of ITER operation. This paper outlines the engineering aspects of the ITER Divertor toroidal rails and focuses on some critical regions of the present design highlighted by the performed structural assessment. The structural assessment has been performed with help of using Finite Element (FE) Abaqus code and based on criteria given by ITER SDC-IC.

Preparation of a large-scale and multi-layer molybdenum crystal and its characteristics

International Nuclear Information System (INIS)

Fujii, Tadayuki

1989-01-01

In the present work, the secondary recrystallization method was applied to obtain a large-scale and multi-layer crystal from a hot-rolled multi-laminated molybdenum sheet doped and stacked alternately with different amounts of dopant. It was found that the time and/or temperature at which secondary recrystallization commence from the multi- layer sheet is strongly dependent on the amounts of dopants. Therefore the potential nucleus of the secondary grain from layers with different amounts of dopant occurred first at the layer with a small amount of dopant and then grew into the layer with a large amount of dopant after an anneal at 1800 0 C-2000 0 C. Consequently a large -scale and multi-layer molybdenum crystal can easily be obtained. 12 refs., 9 figs., 2 tabs. (Author)

Determination of the primary technical parameters of the test bench for controlling the temperature of rails and rail bars of continuous welded rail

Directory of Open Access Journals (Sweden)

Tertychnyi Vitalii

2017-01-01

Full Text Available One of the most important factors determining the reliability and safety of operation of the continuous welded rail track is the temperature of the rails. All conditions of laying, repair and maintenance of the track during the entire cycle of rails operation depend on it. The existing rail temperature monitoring method does not take into account a few significant factors and that leads to significant errors in determining the actual temperature of the rail bar. The authors propose a new rail temperature measurement method on a special test bench which maximally simulates possible environmental operating conditions for the rail bars, the profile of the roadway (embankment or cut, as well as the actual spatial latitude and meridian location of the rail slabs. At the bench, the studied rails are fastened with the help of rail braces on half ties, in the ballast bed, with sizes in accordance with the existing reference documents. At the first stage, the most common KB-65 intermediate fastener for the continuous welded rail in Ukraine will be used, while in subsequent stages KPP-5 fastening will be used.

A systems approach to energy management and policy in commuter rail transportation

Science.gov (United States)

Owan, Ransome Egimine

1998-12-01

This research is motivated by a recognition of energy as a significant part of the transportation problem. Energy is a long-term variable cost that is controllable. The problem is comprised of: the limited supply of energy, chronic energy deficits and oil imports, energy cost, poor fuel substitution, and the undesirable environmental effects of transportation fuels (Green House Gases and global warming). Mass transit systems are energy intensive networks and energy is a direct constraint to the supply of affordable transportation. Commuter railroads are also relatively unresponsive to energy price changes due to travel demand patterns, firm power needs and slow adoption of efficient train technologies. However, the long term energy demand is lacking in existing transportation planning philosophy. In spite of the apparent oversight, energy is as important as urban land use, funding and congestion, all of which merit explicit treatment. This research was conducted in the form of a case study of New Jersey Transit in an attempt to broaden the understanding of the long-term effects of energy in a transportation environment. The systems approach method that is driven by heuristic models was utilized to investigate energy usage, transit peer group efficiency, energy management regimes, and the tradeoffs between energy and transportation, a seldom discussed topic in the field. Implicit in systems thinking is the methodological hunt for solutions. The energy problem was divided into thinking is the methodological hunt for solutions. The energy problem was divided into smaller parts that in turn were simpler to solve. The research presented five heuristic models: Transit Energy Aggregation Model, Structural Energy Consumption Model, Traction Power Consumption Model, Conjunctive Demand Model, and a Managerial Action Module. A putative relationship was established between traction energy, car-miles, seasonal and ambient factors, without inference of direct causality. The co

Managing rail service life

Directory of Open Access Journals (Sweden)

Z. Popović

2014-10-01

Full Text Available The service life of rails depends especially on the operational loads and speeds on the railway lines, as well as on the rail maintenance policy. There are multiple aspects of rail maintenance optimization. The following article considers optimisation of rail maintenance activities relating to rail head surface condition in order to reduce corrective work on track geometry, as well as to minimize the overall costs for track maintenance. The objects of this research are issues and challenges related to rail and track maintenance in curves on modern conventional railway lines for mixed traffic.

Rail passengers rights

Directory of Open Access Journals (Sweden)

Đurđev Dušanka J.

2016-01-01

Full Text Available The legal framework of rail passengers rights is set out in a combination of international and European law: an international measure, the rather unwieldy Uniform Rules concerning the Contract for International Carriage of Passengers and Luggage by Rail, forming part of the Convention concerning International Carriage by Rail of 9 May 1980 (as amended by the Vilnius Protocol of 3 June 1999 ['CIV'], lays down a basic framework which is then fleshed out by more recent EU legislation, Regulation (EC No 1371/2007 on Rail Passengers ' Rights and Obligations. Regulation 1371/2007/EC on rail passenger rights and obligations sets out minimum quality standards that have to be guaranteed to all passengers on all lines. .

Social exclusion and high speed rail: The case study of Spain

Energy Technology Data Exchange (ETDEWEB)

Pagliara, F.; Menicocci, F.; Vassallo, J.M.; Gomez, J.

2016-07-01

Very few contributions in the literature have dealt with the issue of social exclusion related to High Speed Rail systems. The objective of this manuscript is to understand what are the factors excluding users from choosing High Speed Rail services considering as case study Spain. For this purpose, a Revealed Preference survey was employed in November and December 2015. A questionnaire was submitted to users of the Spanish transport systems travelling for long distance-journeys. The aim was that of investigating their perception of High Speed Rail system and the factors inhibiting passengers or excluding them from its use. Data about their socioeconomic characteristics were collected as well. The main result of the survey has been that a relationship between social exclusion and High Speed Rail in Spain is present, especially in terms of geographical exclusion. (Author)

Simultaneous in-bore rail and insulator spectra from a railgun plasma armature

International Nuclear Information System (INIS)

Keefer, D.; Sedghinasah, A.; Crawford, R.

1991-01-01

This paper reports on absolute spectral radiance measurements obtained simultaneously at the rail and insulator surface of the UTSI 1 cm square-bore railgun. The emission spectra were obtained through the use of quartz optical fibers which penetrated both the rail and the insulator walls. The spectral characteristics of the rail and insulator emission are quite similar but differ significantly in magnitude. A detailed plasma radiation model was used to analyze these spectra. In order to obtain reasonable agreement between the model predictions and the experimental spectra, it was necessary to assume that these existed a broadband absorbing layer at the insulator surface. This result suggests a new physical model of the plasma armature in which insulator ablation leads to significant 3-dimensional flow and affects the shape of the current emission pattern on the rail surfaces

Atlanta Rail Yard Study (ARYS): Evaluation of local-scale air pollution trends and emissions quantification using stationary and mobile monitoring strategies

Science.gov (United States)

Intermodal rail yards are important nodes in the freight transportation network, where freight is organized and moved from one mode of transport to another, critical equipment is serviced, and freight is routed to its next destination. Rail yard environments are also areas with ...

On the causal links between health indicator, output, combustible renewables and waste consumption, rail transport, and CO2 emissions: the case of Tunisia.

Science.gov (United States)

Ben Jebli, Mehdi

2016-08-01

This study employs the autoregressive distributed lag (ARDL) approach and Granger causality test to investigate the short- and long-run relationships between health indicator, real GDP, combustible renewables and waste consumption, rail transport, and carbon dioxide (CO2) emissions for the case of Tunisia, spanning the period of 1990-2011. The empirical findings suggest that the Fisher statistic of the Wald test confirm the existence of a long-run relationship between the variables. Moreover, the long-run estimated elasticities of the ARDL model provide that output and combustible renewables and waste consumption have a positive and statistically significant impact on health situation, while CO2 emissions and rail transport both contribute to the decrease of health indicator. Granger causality results affirm that, in the short-run, there is a unidirectional causality running from real GDP to health, a unidirectional causality from health to combustible renewables and waste consumption, and a unidirectional causality from all variables to CO2 emissions. In the long-run, all the computed error correction terms are significant and confirm the existence of long-run association among the variables. Our recommendations for the Tunisian policymakers are as follows: (i) exploiting wastes and renewable fuels can be a good strategy to eliminate pollution caused by emissions and subsequently improve health quality, (ii) the use of renewable energy as a main source for national rail transport is an effective strategy for public health, (iii) renewable energy investment projects are beneficial plans for the country as this contributes to the growth of its own economy and reduce energy dependence, and (iii) more renewable energy consumption leads not only to decrease pollution but also to stimulate health situation because of the increase of doctors and nurses numbers.

Evaluation of alternative public transportation systems in Izmit urban transportation via axiomatic design method

Directory of Open Access Journals (Sweden)

Gülşen AKMAN

2016-02-01

Full Text Available In the world and in our country, most of urban transportation is performed by public transportation. Public transportation is a system which provides transportation easiness and opportunity to people, not to vehicles. Therefore, giving priority to public transportation system is necessary in organizing urban transportation. In this study, in order to reduce traffic intensity and to facilitate passenger transportation in Izmit urban transportation, It is tried to determine appropriate public transportation system. For this, firstly, alternatives which could be used for public transportation were determined. These alternatives are metro, metrobus, tram, light rail system and monorail. Afterwards, the variables affecting decision making about public transportation were determined. These variables are cost, transportation line features, vehicle characteristics, sensitivity to environment and customer satisfaction. Lastly, most appropriate public transportation system is proposed by using the axiomatic design method. As a result, light trail system and metrobus are determined as the most appropriate alternatives for Izmit public transportation system.Keywords: Urban transportation, Multi criteria decision making, Axiomatic design

Modelling of impurity transport in ergodic layer of LHD

International Nuclear Information System (INIS)

Feng, Y.; Masuzaki, S.; Morisaki, T.; Ohyabu, N.; Yamada, H.; Komori, A.; Motojima, O.; Kobayashi, M.

2008-01-01

The impurity transport properties in the ergodic layer of LHD are analyzed by the 3D edge transport code as well as 1D simple model, which is used to illustrate the essential transport terms in the analysis. It is found that as the plasma density increases the edge surface layers, very edge region of the ergodic layer, enters friction dominant regime, resulting in impurity retention. It is considered that the cause for the retention is both temperature drop and the flow acceleration in the edge surface layers. The edge surface layers can provide effective retention of impurities coming from divertor as well as the first wall, because of the geometrical advantage of the edge region of LHD. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Michigan transportation facts & figures : public transportation

Science.gov (United States)

2002-08-16

This on-line document is part of a series, Transportation Facts & Figures, by the Michigan Department of Transportation (MDOT). The Public Transit section of Transportation Facts & Figures cover such topics as intercity bus service, intercity rail se...

Optimal energy management of urban rail systems: Key performance indicators

International Nuclear Information System (INIS)

González-Gil, A.; Palacin, R.; Batty, P.

2015-01-01

Highlights: • An overall picture of urban rail energy use is provided. • Performance indicators are developed for urban rail system energy optimisation. • A multi-level methodology for assessing energy efficiency measures is presented. - Abstract: Urban rail systems are facing increasing pressure to minimise their energy consumption and thusly reduce their operational costs and environmental impact. However, given the complexity of such systems, this can only be effectively achieved through a holistic approach which considers the numerous interdependences between subsystems (i.e. vehicles, operations and infrastructure). Such an approach requires a comprehensive set of energy consumption-related Key Performance Indicators (KEPIs) that enable: a multilevel analysis of the actual energy performance of the system; an assessment of potential energy saving strategies; and the monitoring of the results of implemented measures. This paper proposes an original, complete list of KEPIs developed through a scientific approach validated by different stakeholders. It consists of a hierarchical list of 22 indicators divided into two levels: 10 key performance indicators, to ascertain the performance of the whole system and complete subsystems; and 12 performance indicators, to evaluate the performance of single units within subsystems, for example, a single rail vehicle or station. Additionally, the paper gives a brief insight into urban rail energy usage by providing an adequate context in which to understand the proposed KEPIs, together with a methodology describing their application when optimising the energy consumption of urban rail systems

Fuel Savings and Aerodynamic Drag Reduction from Rail Car Covers

Science.gov (United States)

Storms, Bruce; Salari, Kambiz; Babb, Alex

2008-01-01

The potential for energy savings by reducing the aerodynamic drag of rail cars is significant. A previous study of aerodynamic drag of coal cars suggests that a 25% reduction in drag of empty cars would correspond to a 5% fuel savings for a round trip [1]. Rail statistics for the United States [2] report that approximately 5.7 billion liters of diesel fuel were consumed for coal transportation in 2002, so a 5% fuel savings would total 284 million liters. This corresponds to 2% of Class I railroad fuel consumption nationwide. As part of a DOE-sponsored study, the aerodynamic drag of scale rail cars was measured in a wind tunnel. The goal of the study was to measure the drag reduction of various rail-car cover designs. The cover designs tested yielded an average drag reduction of 43% relative to empty cars corresponding to an estimated round-trip fuel savings of 9%.

Development of planar CT system for multi-layer PCB inspection

Energy Technology Data Exchange (ETDEWEB)

Kim, Seung Ho; Youn, Hanbean; Kam, Soohwa; Park, Eunpyeong; Kim, Ho Kyung [Pusan National University, Busan (Korea, Republic of)

2015-05-15

X-ray defect inspection apparatus can be used in the production line to inspect the PCB. However, a simple X-ray radiography cannot discriminate defects from the multi-layer PCBs because the layers of them overlays the defects. To complement this issue, computed tomography (CT) technology is applied to the NDT system which can offer 3-dimensional information of object. However, CT requires hundreds of projection images to examine a single PCB, hence real-time inspection is nearly impossible. In this study, we develop a planar computed tomography (pCT) system appropriate for the multi-layer PCB inspection. For the image reconstruction of planar cross-section images, we use the digital tomosynthesis (DTS) concept in association with the limited angle scanning. and performance characterization of the pCT system for the PCB inspection. The 3-d Fourier characteristics and more quantitative performance, such as contrast, uniformity, depth resolution will be presented. The cross-sectional images of multi-layer PCBs will also be demonstrated.

Some design aspects of a two-stage rail-to-rail CMOS op amp

NARCIS (Netherlands)

Gierkink, Sander L.J.; Holzmann, Peter J.; Wiegerink, Remco J.; Wassenaar, R.F.

1999-01-01

A two-stage low-voltage CMOS op amp with rail-to-rail input and output voltage ranges is presented. The circuit uses complementary differential input pairs to achieve the rail-to-rail common-mode input voltage range. The differential pairs operate in strong inversion, and the constant

Economic evaluation of current conditions of competition and efficiency of automotive and rail systems in Colombia

International Nuclear Information System (INIS)

Vasco Correa, Carlos Andrés

2012-01-01

This study uses microeconomic data from the transportation systems of land cargo in Colombia: rail and trucking, to determine their degree of allocative efficiency through the non-parametric method Data Envelopment Analysis DEA. The average overall efficiency found was 74.4% for trains and 20.56% for trucks. These figures indicate that rail is more efficient in the allocation of resources. This means that trains in Colombia use their input better than trucks to maximize their production, given the costs and technological characteristics of each system. This is a signal for the design of a public policy for investment in transportation infrastructure that seeks to raise the competitiveness of Colombian exports, investing not only in roads but in complementary systems such as railways too. - Highlights: ► Colombia is currently undergoing a backlog of transport infrastructure and high export costs. ► We perform a microeconomic study of transportation systems in Colombia: rail and trucking. ► As a result we found that the rail is much more efficient than the automotive system. ► As policy recommendation the government should consider the investment in railways. ► It is necessary to take into account the strategic value that investment in railways would bring.

Rail travel: Conceptualizing a study on slow tourism approaches in sustaining rural development

Directory of Open Access Journals (Sweden)

Mohamad Noor Farah Atiqah

2014-01-01

Full Text Available Rail transportation in Peninsular Malaysia is a popular transportation mode for locals to return to their hometown but is not frequently used as the mode of transport when travelling for holidays. Rural towns in Peninsular Malaysia have immense opportunity to be promoted as a popular tourism destination without the need of intense modern development. Using train rather than taking a car or a bus would endorse the concept of slowness during travel enabling tourists to enjoy the time taken to travel rather than rushing to travel to a destination. Encouragement of travelling by rail to the rural towns will enable improved utilization of the existing rail network and further uplift the travel appeal to rural towns in Peninsular Malaysia. In order to promote the concept of slow tourism that would benefit the rural towns’ sustainability, the perception of tourists on travelling slowly by train should first be understood and taken for consideration. A qualitative methodology of in depth interviews with domestic and international tourists whom have travel on trains to the rural towns will be conducted.

Bubble propagation on a rail: a concept for sorting bubbles by size

Science.gov (United States)

Franco-Gómez, Andrés; Thompson, Alice B.; Hazel, Andrew L.; Juel, Anne

We demonstrate experimentally that the introduction of a rail, a small height constriction, within the cross-section of a rectangular channel could be used as a robust passive sorting device in two-phase fluid flows. Single air bubbles carried within silicone oil are generally transported on one side of the rail. However, for flow rates marginally larger than a critical value, a narrow band of bubble sizes can propagate (stably) over the rail, while bubbles of other sizes segregate to the side of the rail. The width of this band of bubble sizes increases with flow rate and the size of the most stable bubble can be tuned by varying the rail width. We present a complementary theoretical analysis based on a depth-averaged theory, which is in qualitative agreement with the experiments. The theoretical study reveals that the mechanism relies on a non-trivial interaction between capillary and viscous forces that is fully dynamic, rather than being a simple modification of capillary static solutions.

Interferential multi-layer mirrors for X-UV radiation: fabrication, characterization and applications

International Nuclear Information System (INIS)

Youn Ki Byoung

1987-01-01

This research thesis reports the fabrication of W/C, Ni/C and Mo/C interferential multi-layer mirrors which can be used in the X-UV domain. They have been manufactured by cathodic pulverisation by using a new system for the in-situ control of the thickness of deposited layers, based on the measurement, sampling and real time integration of the ionic current which goes through the target during the coating process. Different methods (X ray diffraction at different wavelengths, electron microscopy and diffraction, in situ electronic resistivity measurement) have been used to study the main parameters which govern the multi-layer reflectivity: structure, substrate and interface roughness, minimum thickness to be deposited to obtain a continuous layer, number of bi-layers, stacking evenness, rate of absorbent element thickness to the period. Absolute reflectivity measurements have been performed by using short wavelength synchrotron radiation and the S component of polarised soft X rays obtained after double reflection on two parallel multi-layer mirrors oriented according to the Brewster angle. Ferromagnetic properties of Ni/C multi-layers have been studied to investigate fundamental magnetic properties, and to obtain additional information on interface structure [fr

Affordability Assessment to Implement Light Rail Transit (LRT for Greater Yogyakarta

Directory of Open Access Journals (Sweden)

Anjang Nugroho

2015-06-01

Full Text Available The high population density and the increasing visitors in Yogyakarta aggravate the traffic congestion problem. BRT (Bus Rapid Transit services, Trans Jogja has not managed to solve this problem yet. Introducing Light Rail Transit (LRT has been considered as one of the solutions to restrain the congestion in Greater Yogyakarta. As the first indication that the LRT can be built in Greater Yogyakarta, the transportation affordability index was used to understand whether the LRT tariff was affordable. That tariff was calculated based on government policy in determining railway tariff. The forecasted potential passengers and LRT route have been analyzed as the previous steps to get LRT tariff. Potential passenger was forecasted from gravity mode, and the proposed LRT route was chosen using Multi Criteria Decision Analysis (MCDA. The existing transportation affordability index was calculated for comparison analysis using the percentage of the expenditures for transportation made by monthly income of each household. The result showed that the LRT for Greater Yogyakarta was the most affordable transport mode compared to the Trans Jogja Bus and motorcycle. The affordability index of Tram Jogja for people having average income was 10.66% while another people with bottom quartile income was 13.56%. Keywords: Greater Yogyakarta, LRT, affordability.

Estimation of thermal insulation performance in multi-layer insulator for liquid helium pipe

International Nuclear Information System (INIS)

Shibanuma, Kiyoshi; Kuriyama, Masaaki; Shibata, Takemasa

1991-01-01

For a multi-layer insulator around the liquid helium pipes for cryopumps of JT-60 NBI, a multi-layer insulator composed of 10 layers, which can be wound around the pipe at the same time and in which the respective layers are in concentric circles by shifting them in arrangement, has been developed and tested. As the result, it was shown that the newly developed multi-layer insulator has better thermal insulation performance than the existing one, i.e. the heat load of the newly developed insulator composed of 10 layers was reduced to 1/3 the heat load of the existing insulator, and the heat leak at the joint of the insulator in longitudinal direction of the pipe was negligible. In order to clarify thermal characteristics of the multi-layer insulator, the heat transfer through the insulator has been analyzed considering the radiation heat transfer by the netting spacer between the reflectors, and the temperature dependence on the emissivities and the heat transmission coefficients of these two components of the insulator. The analytical results were in good agreements with the experimental ones, so that the analytical method was shown to be valid. Concerning the influence of the number of layers and the layer density on the insulation performance of the insulator, analytical results showed that the multi-layer insulator with the number of layer about N = 20 and the layer density below 2.0 layer/mm was the most effective for the liquid helium pipe of a JT-60 cryopump. (author)

49 CFR 1242.76 - Administration; pickup and delivery, marine line haul, and rail substitute service; loading...

Science.gov (United States)

2010-10-01

... haul, and rail substitute service; loading, unloading and local marine; protective services; freight... SEPARATION OF COMMON OPERATING EXPENSES BETWEEN FREIGHT SERVICE AND PASSENGER SERVICE FOR RAILROADS 1 Operating Expenses-Transportation § 1242.76 Administration; pickup and delivery, marine line haul, and rail...

Policies Towards Suburban Rail Services in Britain and West\\ud Germany – A Comparison.

OpenAIRE

Nash, C.A.

1984-01-01

In 1981, the eight S-Bahn systems of the Federal Republic of Germany carried around 7,000m passenger kilometres of traffic. By contrast, the local rail services operated by British Rail on behalf of the British Passenger Transport Executives were expected to carry around 2,000m passenger kilometres. (Table 1). The aim of this paper is to explore some of the reasons for this enormous difference is the role played by suburban rail systems between the two countries. As illustration, the particul...

Circuit simulation model multi-quantum well laser diodes inducing transport and capture/escape

International Nuclear Information System (INIS)

Zhuber-Okrog, K.

1996-04-01

This work describes the development of world's first circuit simulation model for multi-quantum well (MQW) semiconductor lasers comprising caier transport and capture/escape effects. This model can be seen as the application of a new semiconductor device simulator for quasineutral structures including MQW layers with an extension for simple single mode modeling of optical behavior. It is implemented in a circuit simulation program. The model is applied to Fabry-Perot laser diodes and compared to measured data. (author)

Performance Test of the Microwave Ion Source with the Multi-layer DC Break

International Nuclear Information System (INIS)

Kim, Dae Il; Kwon, Hyeok Jung; Kim, Han Sung; Seol, Kyung Tae; Cho, Yong Sub

2012-01-01

A microwave proton source has been developed as a proton injector for the 100-MeV proton linac of the PEFP (Proton Engineering Frontier Project). On microwave ion source, the high voltage for the beam extraction is applied to the plasma chamber, also to the microwave components such as a 2.45GHz magnetron, a 3-stub tuner, waveguides. If microwave components can be installed on ground side, the microwave ion source can be operated and maintained easily. For the purpose, the multi-layer DC break has been developed. A multi-layer insulation has the arrangement of conductors and insulators as shown in the Fig. 1. For the purpose of stable operation as the multi-layer DC break, we checked the radiation of the insulator depending on materials and high voltage test of a fabricated multi-layer insulation. In this report, the details of performance test of the multi-layer DC break will be presented

Design, simulation and testing of a novel radial multi-pole multi-layer magnetorheological brake

Science.gov (United States)

Wu, Jie; Li, Hua; Jiang, Xuezheng; Yao, Jin

2018-02-01

This paper deals with design, simulation and experimental testing of a novel radial multi-pole multi-layer magnetorheological (MR) brake. This MR brake has an innovative structural design with superposition principle of two magnetic fields generated by the inner coils and the outer coils. The MR brake has several media layers of magnetorheological (MR) fluid located between the inner coils and the outer coils, and it can provide higher torque and higher torque density than conventional single-disk or multi-disk or multi-pole single-layer MR brakes can. In this paper, a brief introduction to the structure of the proposed MR brake was given first. Then, theoretical analysis of the magnetic circuit and the braking torque was conducted. In addition, a 3D electromagnetic model of the MR brake was developed to simulate and examine the magnetic flux intensity and corresponding braking torque. A prototype of the brake was fabricated and several tests were carried out to validate its torque capacity. The results show that the proposed MR brake can produce a maximum braking torque of 133 N m and achieve a high torque density of 25.0 kN m-2, a high torque range of 42 and a high torque-to-power ratio of 0.95 N m W-1.

Substituted polyfluorene-based hole transport layer with tunable solubility

NARCIS (Netherlands)

Craciun, N.I.; Wildeman, J.; Blom, P.W.M.

2010-01-01

We report on the synthesis and electrical characterization of polyfluorene-triarylamine-based hole transport layers (HTLs). The solubility of the HTL can be tuned by adjustment of the chemical structure without loss of the charge transport properties. Double-layer polymer light-emitting diodes are

49 CFR 37.91 - Wheelchair locations and food service on intercity rail trains.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Wheelchair locations and food service on intercity rail trains. 37.91 Section 37.91 Transportation Office of the Secretary of Transportation TRANSPORTATION SERVICES FOR INDIVIDUALS WITH DISABILITIES (ADA) Acquisition of Accessible Vehicles By Public Entities § 37.91 Wheelchair locations and food...

Implications of rail electrodynamics

International Nuclear Information System (INIS)

Rolader, G.E.; Jamison, K.A.

1990-01-01

A model is developed to investigate possible effects of rail electrodynamics on the performance of railguns. This model describes the oscillatory nature of the rail motion in response to the Lorentz force and the compressive restoration force of material which is behind the rails. In this simple model the rails are found to oscillate with a frequency of β. The rail dynamic behavior induces local electric fields. The authors investigate the significance of these electric fields on stationary particles (lab frame) and on particles moving at the velocity of the plasma/projectile system (projectile frame)

Proposals for radioactive material by rail (packaging, labelling and carriage) regulations (Northern Ireland) 1996

International Nuclear Information System (INIS)

1996-01-01

The proposed Radioactive Material by Rail (Packaging, Labelling and Carriage Regulations (Northern Ireland) are presented in this consultation document. The proposals establish a new system of safety controls which implement the requirements of two European Directives. These are the ADR and RID Framework Directives which relate to the transport of dangerous goods by road and rail respectively. (UK)

Five-dimensional Lattice Gauge Theory as Multi-Layer World

OpenAIRE

Murata, Michika; So, Hiroto

2003-01-01

A five-dimensional lattice space can be decomposed into a number of four-dimens ional lattices called as layers. The five-dimensional gauge theory on the lattice can be interpreted as four-dimensional gauge theories on the multi-layer with interactions between neighboring layers. In the theory, there exist two independent coupling constants; $\\beta_4$ controls the dynamics inside a layer and $\\beta_5$ does the strength of the inter-layer interaction.We propose the new possibility to realize t...

Transportation Energy Futures Series: Freight Transportation Demand: Energy-Efficient Scenarios for a Low-Carbon Future

Energy Technology Data Exchange (ETDEWEB)

Grenzeback, L. R.; Brown, A.; Fischer, M. J.; Hutson, N.; Lamm, C. R.; Pei, Y. L.; Vimmerstedt, L.; Vyas, A. D.; Winebrake, J. J.

2013-03-01

Freight transportation demand is projected to grow to 27.5 billion tons in 2040, and to nearly 30.2 billion tons in 2050. This report describes the current and future demand for freight transportation in terms of tons and ton-miles of commodities moved by truck, rail, water, pipeline, and air freight carriers. It outlines the economic, logistics, transportation, and policy and regulatory factors that shape freight demand, the trends and 2050 outlook for these factors, and their anticipated effect on freight demand. After describing federal policy actions that could influence future freight demand, the report then summarizes the capabilities of available analytical models for forecasting freight demand. This is one in a series of reports produced as a result of the Transportation Energy Futures project, a Department of Energy-sponsored multi-agency effort to pinpoint underexplored strategies for reducing GHGs and petroleum dependence related to transportation.

78 FR 16036 - Service Level Environmental Impact Statement for the Texas Oklahoma Passenger Rail Study Corridor...

Science.gov (United States)

2013-03-13

... transportation modes such as auto, air travel, intercity bus, and existing rail and the physical characteristics... alternatives to provide higher speed passenger rail service to meet future intercity travel demand and to... truck traffic demand, intercity truck traffic demand, and passenger travel demand compete for highway...

Analysis and modeling of rail maintenance costs

Directory of Open Access Journals (Sweden)

Amir Ali Bakhshi

2012-01-01

Full Text Available Railroad maintenance engineering plays an important role on availability of roads and reducing the cost of railroad incidents. Rail is of the most important parts of railroad industry, which needs regular maintenance since it covers a significant part of total maintenance cost. Any attempt on optimizing total cost of maintenance could substantially reduce the cost of railroad system and it can reduce total cost of the industry. The paper presents a new method to estimate the cost of rail failure using different cost components such as cost of inspection and cost of risk associated with possible accidents. The proposed model of this paper is used for a real-world case study of railroad transportation of Tehran region and the results have been analyzed.

AFFORDABLE MULTI-LAYER CERAMIC (MLC) MANUFACTURING FOR POWER SYSTEMS (AMPS)

Energy Technology Data Exchange (ETDEWEB)

E.A. Barringer, Ph.D.

2002-11-27

McDermott Technology, Inc. (MTI) is attempting to develop high-performance, cost-competitive solid oxide fuel cell (SOFC) power systems. Recognizing the challenges and limitations facing the development of SOFC stacks comprised of electrode-supported cells and metallic interconnects, McDermott Technology, Inc. (MTI) has chosen to pursue an alternate path to commercialization. MTI is developing a multi-layer, co-fired, planar SOFC stack that will provide superior performance and reliability at reduced costs relative to competing designs. The MTI approach combines state-of-the-art SOFC materials with the manufacturing technology and infrastructure established for multi-layer ceramic (MLC) packages for the microelectronics industry. The rationale for using MLC packaging technology is that high quality, low-cost manufacturing has been demonstrated at high volumes. With the proper selection of SOFC materials, implementation of MLC fabrication methods offers unique designs for stacks (cells and interconnects) that are not possible through traditional fabrication methods. The MTI approach eliminates use of metal interconnects and ceramic-metal seals, which are primary sources of stack performance degradation. Co-fired cells are less susceptible to thermal cycling stresses by using material compositions that have closely matched coefficients of thermal expansion between the cell and the interconnect. The development of this SOFC stack technology was initiated in October 1999 under the DOE cosponsored program entitled ''Affordable Multi-layer Ceramic Manufacturing for Power Systems (AMPS)''. The AMPS Program was conducted as a two-phase program: Phase I--Feasibility Assessment (10/99--9/00); and Phase II--Process Development for Co-fired Stacks (10/00-3/02). This report provides a summary of the results from Phase I and a more detailed review of the results for Phase II. Phase I demonstrated the feasibility for fabricating multi-layer, co-fired cells and

Rail deployment and storage procedure and test for ITER blanket remote maintenance

International Nuclear Information System (INIS)

Kakudate, S.; Shibanuma, K.

2003-01-01

A concept of rail-mounted vehicle manipulator system has been developed to apply to the maintenance of the ITER blanket composed of ∼400 modules in the vacuum vessel. The most critical issue of the vehicle manipulator system is the feasibility of the deployment and storage of the articulated rail, composed of eight rail links without any driving mechanism in the joints. To solve this issue, a new driving mechanism and procedure for the rail deployment and storage has been proposed, taking account of the repeated operation of the multi-rail links deployed and stored in the same kinematical manner. The new driving mechanism, which is different from those of a usual articulated manipulator or 'articulated boom' equipped with actuators in every joint for movement, is composed of three external mechanisms installed outside the articulated rail, i.e. a vehicle traveling mechanism as main driver and two auxiliary driving mechanisms. A simplified synchronized control of three driving mechanisms has also been proposed, including 'torque-limit control' for suppression of the overload of the mechanisms. These proposals have been tested using a full-scale vehicle manipulator system, in order to demonstrate the proof of principle for rail deployment and storage. As a result, the articulated rail has been successfully deployed and stored within 6 h each, less than the target of 8 h, by means of the three external driving mechanisms and the proposed synchronized control. In addition, the overload caused by an unexpected mismatch of the synchronized control of three driving mechanisms has also been successfully suppressed less than the rated torque by the proposed 'torque-limit control'. It is therefore concluded that the feasibility of the rail deployment and storage of the vehicle manipulator system has been demonstrated

Long Term Land Use Effects of New Rail Investment: Lessons from San Diego

Directory of Open Access Journals (Sweden)

David A. King

2018-01-01

Full Text Available In recent decades, U.S. cities have invested in rail transit for reasons beyond supplying alternatives to driving. Increasingly, rail investments are specifically promoted to reshape the built environment for property-led economic development. In these cases, new investment in rail transit is claimed to facilitate particular types of land use changes, mostly in the form of dense multi-family residential and mixed-use developments. Although rail’s effects on land use are widely claimed, scholarly evaluations offer mixed results. This paper examines two potential reasons for these mixed results. First, as most empirical examinations tend to be conducted shortly after new transit investment opens analysis is often criticized on the basis that short time frames may not allow land use changes to materialize. The second is that rail investment often includes changes to local zoning and land use regulations, creating opportunities for types of development that were previously outlawed. This paper evaluates these two critiques through an analysis of long-term land use effects associated with new rail transit service in San Diego, California. The results suggest that even after three decades of development cycles, rail transit has not led to consistent regulatory patterns of increased density or new mixed-use development.

Rail flaw sizing using conventional and phased array ultrasonic testing.

Science.gov (United States)

2012-12-01

An approach to detecting and characterizing internal defects in rail through the use of phased array ultrasonic testing has shown the potential to reduce the risk of missed defects and improve transverse defect characterization. : Transportation Tech...

Perspectives in high-speed transport: Maglev and/or wheel-and-rail techniques

Energy Technology Data Exchange (ETDEWEB)

Hochbruck, H

1985-03-01

Proceeding from a consideration of possible system structures, a technically and economically meaning-full top speed for a railway system is developed which offers, in competition with the airplane and the private car, good chances of winning an appropriate share of the traffic where the distances are in the range of about 400 to 600 km. It is deduced from the present state of developments in high-speed wheel/rail systems and in maglev technology that the wheel/rail mode has clear advantages where a network is concerned. Maglev technology is now being brought to the stage of operational readiness and its first applications are likely to be for point-to-point or direct-line links.

Development of a low activation concrete shielding wall by multi-layered structure for a fusion reactor

International Nuclear Information System (INIS)

Sato, Satoshi; Maegawa, Toshio; Yoshimatsu, Kenji; Sato, Koichi; Nonaka, Akira; Takakura, Kosuke; Ochiai, Kentaro; Konno, Chikara

2011-01-01

A multi-layered concrete structure has been developed to reduce induced activity in the shielding for neutron generating facilities such as a fusion reactor. The multi-layered concrete structure is composed of: (1) an inner low activation concrete, (2) a boron-doped low activation concrete as the second layer, and (3) ordinary concrete as the outer layer of the neutron shield. With the multi-layered concrete structure the volume of boron is drastically decreased compared to a monolithic boron-doped concrete. A 14 MeV neutron shielding experiment with multi-layered concrete structure mockups was performed at FNS and several reaction rates and induced activity in the mockups were measured. This demonstrated that the multi-layered concrete effectively reduced low energy neutrons and induced activity.

Evaluation of polyethylenimine/carrageenan multi-layer for antibacterial activity of pathogenic bacteria

International Nuclear Information System (INIS)

Briones, Annabelle V.; Bigol, Urcila G.; Sato, Toshinori

2012-01-01

The purpose of this study is to investigate the antibacterial activity of multi-layer of polyethylenimine (PEI) and carrageenan (κ,ι, λ) for potential use as coating on biomaterial surface. The multi-layer of PEI/carrageenan was formed using the layer-by-layer assembly absorption technique and was monitored by atomic force microscopy (AFM) and bio molecular interaction analysis. All samples were prepared in phosphate buffer solution and applied to mica disk alternately. The micrographs showed the formation of bi-layer of polyethylenimine and carrageenan (κ, ι, λ) as observed in the change of height of the layer and surface morphology. The bimolecular binding of carrageenan with polyethylenimine was also investigated using a biosensor. The sensorgram showed that PEI interacted molecularly with carrageenan. Results were: 1,916.08 pg/nm 2 for kappa type; 1,844.1 pg/nm 2 for iota type and 6,074.24 pg/nm 2 for lambda type. The multi-layer showed antibacterial activity against Enterobacter cloaceae, Staphylococcus aureus and Enterococcal strains (Enterococcus faecalis (EF) 29212 and 29505). (author)

75 FR 76520 - Tennessee Southern Railroad Company, Patriot Rail, LLC, Patriot Rail Holdings LLC, and Patriot...

Science.gov (United States)

2010-12-08

... family by converting two of its subsidiaries from corporations into limited liability companies: (1... Railroad Company, Patriot Rail, LLC, Patriot Rail Holdings LLC, and Patriot Rail Corp.--Corporate Family... Railroad Company (TSRR), Patriot Rail, LLC (PRL) and its subsidiaries, Patriot Rail Holdings LLC (PRH) and...

Framing Light Rail Projects

DEFF Research Database (Denmark)

Olesen, Mette

2014-01-01

In Europe, there has been a strong political will to implement light rail. This article contributes to the knowledge concerning policies around light rail by analysing how local actors frame light rail projects and which rationalities and arguments are present in this decision-making process....... The article draws on the socio-technical approach to mobilities studies in order to reassemble the decision-making process in three European cases: Bergen, Angers, and Bern. This article provides insights into the political, discursive and material production of light rail mobilities in a European context....... It identifies the planning rationales behind the systems and the policies that have been supportive of this light rail vision. Finally, the article identifies the practical challenges and potentials that have been connected to the different local frames of light rail mobility which can be used in future...

A Bilevel Programming Model to Optimize Train Operation Based on Satisfaction for an Intercity Rail Line

Directory of Open Access Journals (Sweden)

Zhipeng Huang

2014-01-01

Full Text Available The passenger travel demands for intercity rail lines fluctuate obviously during different time periods, which makes the rail departments unable to establish an even train operation scheme. This paper considers an optimization problem for train operations which respond to passenger travel demands of different periods in intercity rail lines. A satisfactory function of passenger travelling is proposed by means of analyzing the passengers’ travel choice behavior and correlative influencing factors. On this basis, the paper formulates a bilevel programming model which maximizes interests of railway enterprises and travelling satisfaction of each passenger. The trains operation in different periods can be optimized through upper layer planning of the model, while considering the passenger flow distribution problem based on the Wardrop user equilibrium principle in the lower layer planning. Then, a genetic algorithm is designed according to model features for solving the upper laying. The Frank-Wolfe algorithm is used for solving the lower layer planning. Finally, a numerical example is provided to demonstrate the application of the method proposed in this paper.

Identification and prioritization of rail squat defects in the field using rail magnetisation technology

Science.gov (United States)

Kaewunruen, Sakdirat

2015-04-01

Inevitably, rail squats and studs are continuing to be a serious problem for railway organisations around the world in the 21st century. They are typically classified as the growth of any cracks that have grown longitudinally through the subsurface and some of the cracks propagating to the bottom of rails transversely, and have branched from initial longitudinal cracks with a depression of rail surface. The horizontal crack, which results in a depression of rail surface, induces increased maintenance level, more frequent monitoring, compromised rail testing (as the crack shields the signal echoes), and possible broken rails. This paper presents field investigations using a magnetised-rail testing device developed by MRX Technologies to identify and prioritise the rail squats. Most of the in situ squats were found on the high rail of the transition (variable-radius curved track), which is associated with rolling contact fatigue (RCF). This investigation highlights the field performance of the MRX's surface crack detection technology in comparison with the traditional ultrasonic method and detailed walking inspection. Visually, it was found in the field that the size of the RCF squats varies from very small to moderate. The predicted crack data were obtained by scanning the magnitised rails. The comparison of the actual crack depths (ultrasonic) and the predicted crack depths (MRX device) shows: • A possible correlation for small RCF/ squat cracks. • Poor interpretation of larger defects and welds. The field assessment also suggests some practical issues required for further development, including the detection of rail spalling, deep transverse crack, welding, and so on.

Fuel element transport container

International Nuclear Information System (INIS)

Benna, P.; Neuenfeldt, W.

1979-01-01

The reprocessing system includes a large number of waterfilled ponds next to each other for the intermediate storage of fuel elements from LWR's. The fuel element transport device is allocated to a middle pond. The individual ponds are separated from each other by walls, and are only accessible from the middle pond via narrow passages. The transport device includes a telescopic running rail for a trolley with a grab device for the fuel element. The running rail is supported in turn by a second trolley, which can be moved by wheels on rails. Part of the drive of the first trolley is arranged on the second one. Using this transport device, adjacent ponds can be served through the passage openings. (DG) [de

Performance of Rail Fastening Systems on an Open-Deck Bridge

Science.gov (United States)

2018-02-01

Transportation Technology Center, Inc. (TTCI) monitored the performance of rail fasteners on an open-deck bridge and its approaches, located at Norfolk Southern Corporations (NS's) eastern mega site. The project was co-sponsored by the Federal Rai...

Transportation Technology: Rail Transport and Logistics

Science.gov (United States)

Lang, Aaron B.

2011-01-01

Transportation can simply be defined as the movement of goods, services, and people from one location to another. Without an efficient means to transport goods from place to place, the economy would be nothing like it is today. Throughout the history of the United States, American railroads have paved the way toward creating a nation of great…

Investigation of a Resonant dc–dc Converter for Light Rail Transportation Applications

Directory of Open Access Journals (Sweden)

Bor-Ren Lin

2018-04-01

Full Text Available A high efficiency dc–dc converter is studied for light rail transportation applications on DC microgrid systems. The adopted structure includes two series-connected resonant circuits with single isolated transformer from input 750 V to output 48 V. Two half-bridge resonant circuits and one voltage balance capacitor are used to reduce voltage rating of active devices and to realize split voltages balance. Two series resonant circuits are connected with input-series by single transformer to reduce primary root-mean-square currents. Therefore, power devices with low voltage rating are selected in studied circuit to reduce power loss on sower devices and transformer winding of the isolated transformer. Frequency control approach is adopted to adjust load voltage under different voltage condition and current variations. Since the equivalent resonant tank of the studied circuit is activated under inductive load, active devices are easily operated at zero-voltage switching over wide voltage and current operation range. The feasibility of the studied circuit has been verified with a 1 kW prototype.

An Evaluation of the Low-Carbon Effects of Urban Rail Based on Mode Shifts

Directory of Open Access Journals (Sweden)

Feng Chen

2017-03-01

Full Text Available Urban rail is widely considered to be a form of low-carbon green transportation, but there is a lack of specific quantitative research to support this. By comparing the mode, distance, and corresponding energy consumption of residents before and after the opening of rail transit, this paper establishes a carbon reduction method for rail transit. A measurement model takes the passenger carbon emissions before the line is opened as the baseline and compares them with the standard after the opening, determining the carbon emissions reduction. The model requires a combination of a large amount of research data, transit smart card data, and GIS network measurement tools as measured data and parameters. The model is then applied to rail transit lines that have opened in Beijing in recent years. The emissions reductions of four different routes are estimated and the carbon emissions reduction effect of rail transit is evaluated.

Calibration of robotic drilling systems with a moving rail

Directory of Open Access Journals (Sweden)

Tian Wei

2014-12-01

Full Text Available Industrial robots are widely used in aircraft assembly systems such as robotic drilling systems. It is necessary to expand a robot’s working range with a moving rail. A method for improving the position accuracy of an automated assembly system with an industrial robot mounted on a moving rail is proposed. A multi-station method is used to control the robot in this study. The robot only works at stations which are certain positions defined on the moving rail. The calibration of the robot system is composed by the calibration of the robot and the calibration of the stations. The calibration of the robot is based on error similarity and inverse distance weighted interpolation. The calibration of the stations is based on a magnetic strip and a magnetic sensor. Validation tests were performed in this study, which showed that the accuracy of the robot system gained significant improvement using the proposed method. The absolute position errors were reduced by about 85% to less than 0.3 mm compared with the maximum nearly 2 mm before calibration.

Compressed Air/Vacuum Transportation Techniques

Science.gov (United States)

Guha, Shyamal

2011-03-01

General theory of compressed air/vacuum transportation will be presented. In this transportation, a vehicle (such as an automobile or a rail car) is powered either by compressed air or by air at near vacuum pressure. Four version of such transportation is feasible. In all versions, a ``c-shaped'' plastic or ceramic pipe lies buried a few inches under the ground surface. This pipe carries compressed air or air at near vacuum pressure. In type I transportation, a vehicle draws compressed air (or vacuum) from this buried pipe. Using turbine or reciprocating air cylinder, mechanical power is generated from compressed air (or from vacuum). This mechanical power transferred to the wheels of an automobile (or a rail car) drives the vehicle. In type II-IV transportation techniques, a horizontal force is generated inside the plastic (or ceramic) pipe. A set of vertical and horizontal steel bars is used to transmit this force to the automobile on the road (or to a rail car on rail track). The proposed transportation system has following merits: virtually accident free; highly energy efficient; pollution free and it will not contribute to carbon dioxide emission. Some developmental work on this transportation will be needed before it can be used by the traveling public. The entire transportation system could be computer controlled.

Bulk and interface quantum states of electrons in multi-layer heterostructures with topological materials

Science.gov (United States)

Nikolic, Aleksandar; Zhang, Kexin; Barnes, C. H. W.

2018-06-01

In this article we describe the bulk and interface quantum states of electrons in multi-layer heterostructures in one dimension, consisting of topological insulators (TIs) and topologically trivial materials. We use and extend an effective four-band continuum Hamiltonian by introducing position dependence to the eight material parameters of the Hamiltonian. We are able to demonstrate complete conduction-valence band mixing in the interface states. We find evidence for topological features of bulk states of multi-layer TI heterostructures, as well as demonstrating both complete and incomplete conduction-valence band inversion at different bulk state energies. We show that the linear k z terms in the low-energy Hamiltonian, arising from overlap of p z orbitals between different atomic layers in the case of chalcogenides, control the amount of tunneling from TIs to trivial insulators. Finally, we show that the same linear k z terms in the low-energy Hamiltonian affect the material’s ability to form the localised interface state, and we demonstrate that due to this effect the spin and probability density localisation in a thin film of Sb2Te3 is incomplete. We show that changing the parameter that controls the magnitude of the overlap of p z orbitals affects the transport characteristics of the topologically conducting states, with incomplete topological state localisation resulting in increased backscattering.

Bronze railing from Mediana

Directory of Open Access Journals (Sweden)

Vasić Miloje R.

2003-01-01

Full Text Available The hoard containing components of bronze railing was discovered in trench 7 during excavations at Mediana in 2000. Railing consists of cancelli and herms with busts of deities between them. Railing was constructed in such a way that it was possible to disassemble and reassemble it. Three cancelli one fragmented semicancellus cast together with herm and herms, one with bust of Aesculapius and other with bust of Luna. It could be concluded that railing consisted of two segments with passage between them. Male deities were represented on the left segment of the railing and female deities on the right segment. Detailed analysis revealed that Aesculapius as well as Luna bear strong mark of classical Greek and Hellenistic art, which experienced some kind of renaissance in the time of Constantine I. It is very probable that we can recognize the portrait of Faustina, Constantine’s wife in the portrait of Luna. According to the historical events the railing could have been produced before 325 AD when Constantine definitively accepted Christianity at Council of Nicaea. It is difficult to say where the railing had been produced. It had been most probably brought to Mediana during the stay of emperor Julian in Niš in 361. The sculptures found in one room of the villa with peristyle had probably been brought at the same time. The apse of triclinium of this villa had most likely been arranged as small shrine with bronze railing at its entrance. The railing was buried in 378 after battle of Adrianople and invasion of Goths in diocese Dacia.

Changes in Service and Associated Ridership Impacts near a New Light Rail Transit Line

Directory of Open Access Journals (Sweden)

Jeongwoo Lee

2017-10-01

Full Text Available Los Angeles (LA, for many years a city with limited rail transit, is substantially expanding its public transit system. This paradigm change in transportation policy and investment creates new requirements for monitoring. One area needing evaluation is whether new, high quality transit options, such as light rail, near existing transit services increase sustainable transportation mode shares and reduce car travel. Few studies have explored light rail’s role as a catalyst to increase overall transit use and achieve sustainability goals within an auto-oriented city like LA. Metro’s data show that trips taken on its bus and rail system dropped overall by 10.5% between 2009 and 2016, but its rail ridership grew 21% during the same period due to the debut of the Gold Line and Expo Line extensions. We analyze changes to bus service and associated ridership impacts that resulted from the opening of these two LRT lines in LA. The immediate effect of the city’s bus service changes along the Gold Line light rail extension appear to be associated with a net “bus plus rail” ridership decline in that corridor. In contrast, the Expo Line corridor experienced an initial increase in ridership during the two years immediately after its opening, possibly because the bus service was not reduced by the same magnitude as along the Gold Line extension. Our findings indicate that changes in bus service made to coincide with the introduction of new light rail transit (LRT can negatively affect the overall transit ridership in the corridor. Planners and policy makers should closely monitor changes in bus service and ridership associated with new rail transit to ensure investments results in an overall net increase in more sustainable travel.

Remote Multi-layer Soil Temperature Monitoring System Based on GPRS

Directory of Open Access Journals (Sweden)

Ming Kuo CHEN

2014-02-01

Full Text Available There is the temperature difference between the upper and lower layer of the shallow soil in the forest. It is a potential energy that can be harvested by thermoelectric generator for the electronic device in the forest. The temperature distribution at different depths of the soil is the first step for thermoelectric generation. A remote multi-layer soil temperature monitoring system based on GPRS is proposed in this paper. The MSP430F149 MCU is used as the main controller of multi-layer soil temperature monitoring system. A temperature acquisition module is designed with DS18B20 and 4 core shielded twisted-pair cable. The GPRS module sends the measured data to remote server through wireless communication network. From the experiments in the campus of Beijing Forestry University, the maximum error of measured temperature in this system is 0.2°C by comparing with professional equipment in the same condition. The results of the experiments show that the system can accurately realize real-time monitoring of multi-layer soil temperature, and the data transmission is stable and reliable.

A low-voltage Op Amp with rail-to-rail constant-gm input stage and a class AB rail-to-rail output stage

NARCIS (Netherlands)

Botma, J.H.; Wassenaar, R.F.; Wiegerink, Remco J.

1993-01-01

In this paper a low-voltage two-stage Op Amp is presented. The Op Amp features rail-to-rail operation and has an @put stage with a constant transconductance (%) over the entire common-mode input range. The input stage consists of an n- and a PMOS differential pair connected in parallel. The constant

Multi-filamentary REBCO tapes fabricated by scratching a buffer layer along the tape longitudinal direction

Energy Technology Data Exchange (ETDEWEB)

Kurihara, Chihaya, E-mail: chihaya.kurihara@jp.fujikura.com [Fujikura Ltd., 1440, Mutsuzaki, Sakura, Chiba 285-8550 (Japan); Fujita, Shinji; Nakamura, Naonori; Igarashi, Mitsunori; Iijima, Yasuhiro [Fujikura Ltd., 1440, Mutsuzaki, Sakura, Chiba 285-8550 (Japan); Higashikawa, Kohei; Uetsuhara, Dai; Kiss, Takanobu; Iwakuma, Masataka [Kyushu University, 744 Motooka, Nishi-Ku, Fukuoka 819-0395 (Japan)

2016-11-15

Highlights: • We developed new method of slitting tape between buffer layer processes for multi-filamentary tape. • By scratching buffer layer along the tape longitudinal direction, we find that REBCO layer is divided easily without damaging it. • We have developed 100 m class multi-filamentary REBCO tapes which are suitable for superconducting coils. - Abstract: A method for making multi-filamentary REBCO tapes by only scratching buffer layer was developed for coil application which requires accurate magnetic fields. By continuous I{sub c} measurement, we found that our new multi-filamentary tape could provide almost equal I{sub c} compared to conventional tapes. Then, using EBSD and RTR-SHPM methods, a divided structure of REBCO layer was surely confirmed. AC loss was also decreased. Furthermore, the result of delamination test of our new multi-filamentary tape showed enough mechanical property. As a result, we have succeeded in developing 100 m class multi-filamentary tape for superconducting coil.

Multi-filamentary REBCO tapes fabricated by scratching a buffer layer along the tape longitudinal direction

International Nuclear Information System (INIS)

Kurihara, Chihaya; Fujita, Shinji; Nakamura, Naonori; Igarashi, Mitsunori; Iijima, Yasuhiro; Higashikawa, Kohei; Uetsuhara, Dai; Kiss, Takanobu; Iwakuma, Masataka

2016-01-01

Highlights: • We developed new method of slitting tape between buffer layer processes for multi-filamentary tape. • By scratching buffer layer along the tape longitudinal direction, we find that REBCO layer is divided easily without damaging it. • We have developed 100 m class multi-filamentary REBCO tapes which are suitable for superconducting coils. - Abstract: A method for making multi-filamentary REBCO tapes by only scratching buffer layer was developed for coil application which requires accurate magnetic fields. By continuous I_c measurement, we found that our new multi-filamentary tape could provide almost equal I_c compared to conventional tapes. Then, using EBSD and RTR-SHPM methods, a divided structure of REBCO layer was surely confirmed. AC loss was also decreased. Furthermore, the result of delamination test of our new multi-filamentary tape showed enough mechanical property. As a result, we have succeeded in developing 100 m class multi-filamentary tape for superconducting coil.

Rail vehicle dynamics

CERN Document Server

Knothe, Klaus

2017-01-01

This book on the dynamics of rail vehicles is developed from the manuscripts for a class with the same name at TU Berlin. It is directed mainly to master students with pre-knowledge in mathematics and mechanics and engineers that want to learn more. The important phenomena of the running behaviour of rail vehicles are derived and explained. Also recent research results and experience from the operation of rail vehicles are included. One focus is the description of the complex wheel-rail contact phenomena that are essential to understand the concept of running stability and curving. A reader should in the end be able to understand the background of simulation tools that are used by the railway industry and universities today.

Chicago to Iowa City intercity passenger rail route : business plan.

Science.gov (United States)

2011-03-21

This business plan describes the methods by which the Iowa Department of Transportation (DOT will partner with Iowa counties and cities to fund Iowas share of the operating and maintenance cost for the Chicago-Iowa City passenger-rail service, an ...

Návrh Rail-to-Rail proudového konvejoru v technologii CMOS

OpenAIRE

Hudzik, Martin

2016-01-01

Diplomová práca sa zaoberá návrhom rail-to-rail prúdového konvejora druhej generácie v technológii CMOS. Opisuje princípy funkcie jednotlivých generácii prúdových konvejorov a taktiež základný princíp návrhu prúdového konvejora druhej generácie založeného na operačnom zosilňovači. Venuje sa obvodovému riešeniu vstupného rail-to-rail stupňa a koncového stupňa v triede AB. Cieľom tejto práce je navrhnúť, charakterizovať vlastnosti a vytvoriť topológiu prúdového konvejora druhej generácie s rail...

By-law from December 6, 1996 relative to the rail transport of dangerous goods (called ''RID by-law''). (Dangerous materials no. 2)

International Nuclear Information System (INIS)

Mesnil, H. du

1996-01-01

The aim of this by-law from the French ministry of equipment, lodging, transports and tourism is to define the specific rules that must be applied in France to the national or international rail transport of dangerous freight (radioactive materials, explosive materials, under pressure compressed, liquefied or dissolved gases, flammable liquids and solids, spontaneously flammable materials, combustive agents, organic peroxides, noxious, infectious and corrosive materials etc..). The classification of dangerous materials and the freight that cannot be transported by train is listed in two appendixes [700 p.] at the end of the document. This by-law gives the rules concerning: the building, testing, agreement, labelling, periodical controls and conditions for use of packing materials, drums, containers and tank wagons; the equipments, the loading and unloading, the running and parking of wagons; the documents relative to the transport. (J.S.)

Design of Low Voltage Low Power CMOS OP-AMPS with Rail-to-Rail Input/Output Swing

OpenAIRE

Gopalaiah, SV; Shivaprasad, AP; Panigrahi, Sukanta K

2004-01-01

A novel input and output biasing circuit to extend the input common mode (CM) voltage range and the output swing to rail-to-rail in a low voltage op-amp in standard CMOS technology is presented. The input biasing circuit uses a Switched Capacitor Based Attenuator (SCBA) approach to establish rail-to-rail common mode input voltage range. And the output biasing circuit uses an Output Driver (OD), with floating bias to give the rail-to-rail swing at output stage. Three different OD schemes in op...

Multi-layer Far-Infrared Component Technology, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This Phase I SBIR will demonstrate the feasibility of a process to create multi-layer thin-film optics for the far-infrared/sub-millimeter wave spectral region. The...

Road transport of LWR spent fuel in the Federal Republic of Germany

International Nuclear Information System (INIS)

Bach, R.

1987-01-01

Since 1967, when fuel from LWRs was first transported by road from the Kahl reactor in the Federal Republic of Germany to the Eurochemic reprocessing plant in Belgium, a total of more than 400 road transports have been performed without any adverse effect on the environment. In the beginning, road transport was the dominant mode. However, in recent years large capacity rail flasks with a weight ranging from 80 to 110 tonnes have been put into service in order to cope with the increasing demand of transport services and to replace existing smaller flasks designed primarily for road transport. Therefore, the number of spent fuel transports by road has declined. However, road transport of heavy flasks from reactor sites without a direct rail link to a nearby rail terminal has become an important task and a number of special problems have had to be solved. The following items are discussed, with special emphasis placed on heavy load transports by road from the reactor to a nearby rail terminal: design of road transport equipment to meet the requirements of the national traffic law; application of technical and administrative procedures to meet the IAEA Regulations; transport restrictions due to overload/oversize; transfer of the flask from the reactor to the transport vehicle; handling of the flask at the rail terminal; turn-around inspection and periodic maintenance of equipment to ensure safe performance of transport; and physical protection during transport and handling at rail terminals. (author). 4 figs

Risk of transporting plutonium dioxide and liquid plutonium nitrate by truck and rail

International Nuclear Information System (INIS)

Williams, L.D.; Hall, R.J.

1976-01-01

This paper presents an analysis method developed to assess the risk in the transportation of radioactive materials and demonstrates its application by summarizing the results of risk assessments of the shipment of plutonium dioxide powder and liquid plutonium nitrate by truck and rail in the United States. In the risk assessment, postulated release modes (series of events that could result in a release of radioactive material) are identified using the fault tree analysis method. Two categories of events that could contribute to a release during transportation are considered: accidents and substandard packaging conditions. The likelihood of basic events in these categories are determined from general accident experience, radioactive material shipping experience, engineering analysis, etc. Using the laws of combining probabilities, the likelihood of radioactive material release is then evaluated. Since accidents vary greatly in severity, the releases from these postulated events also vary in magnitude from the no release condition up through release of the entire package contents. The bases for the release quantities assigned to the postulated accidents sequences are discussed. The consequences of these postulated releases are evaluated based on the amount of plutonium estimated to be released to the environs, the probable weather conditions at the time of the accident, and population density downwind from the accident scene. The likelihood and consequence of postulated releases are coupled and expressed as a risk spectra. (author)

The transmission of finite amplitude sound beam in multi-layered biological media

Science.gov (United States)

Liu, Xiaozhou; Li, Junlun; Yin, Chang; Gong, Xiufen; Zhang, Dong; Xue, Honghui

2007-02-01

Based on the Khokhlov Zabolotskaya Kuznetsov (KZK) equation, a model in the frequency domain is given to describe the transmission of finite amplitude sound beam in multi-layered biological media. Favorable agreement between the theoretical analyses and the measured results shows this approach could effectively describe the transmission of finite amplitude sound wave in multi-layered biological media.

The transmission of finite amplitude sound beam in multi-layered biological media

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiaozhou [Key Lab of Modern Acoustics, Institute of Acoustics, Nanjing University, Nanjing 210093 (China)]. E-mail: xzliu@nju.edu.cn; Li, Junlun [Key Lab of Modern Acoustics, Institute of Acoustics, Nanjing University, Nanjing 210093 (China); Yin, Chang [Key Lab of Modern Acoustics, Institute of Acoustics, Nanjing University, Nanjing 210093 (China); Gong, Xiufen [Key Lab of Modern Acoustics, Institute of Acoustics, Nanjing University, Nanjing 210093 (China); Zhang, Dong [Key Lab of Modern Acoustics, Institute of Acoustics, Nanjing University, Nanjing 210093 (China); Xue, Honghui [Key Lab of Modern Acoustics, Institute of Acoustics, Nanjing University, Nanjing 210093 (China)

2007-02-19

Based on the Khokhlov-Zabolotskaya-Kuznetsov (KZK) equation, a model in the frequency domain is given to describe the transmission of finite amplitude sound beam in multi-layered biological media. Favorable agreement between the theoretical analyses and the measured results shows this approach could effectively describe the transmission of finite amplitude sound wave in multi-layered biological media.

The transmission of finite amplitude sound beam in multi-layered biological media

International Nuclear Information System (INIS)

Liu, Xiaozhou; Li, Junlun; Yin, Chang; Gong, Xiufen; Zhang, Dong; Xue, Honghui

2007-01-01

Based on the Khokhlov-Zabolotskaya-Kuznetsov (KZK) equation, a model in the frequency domain is given to describe the transmission of finite amplitude sound beam in multi-layered biological media. Favorable agreement between the theoretical analyses and the measured results shows this approach could effectively describe the transmission of finite amplitude sound wave in multi-layered biological media

Exploring the Role of Online ‘Ojek’ In Public Transport Trips: Case of Jakarta Metropolitan Area Rail Users

Science.gov (United States)

Saffan, A. F.; Rizki, M.

2018-05-01

The invention of information technology shapes people’s lives in the city, including the recent invention of online motorcycle taxi service. Known as ‘ojek’, it offers a reliable means of tactical commuting in dealing with traffic congestion in Greater Jakarta. Moreover, recent development in the online system improves the punctuality and reliability of ojek services. The emergence disrupts the transport landscape, resulting in commuters’ dependency to this transport mode. However, academic sources are insufficient to answer the policy debate among planners and policy maker regarding this issue. This paper probes the role of online ojek in Jakarta Metropolitan Area Rail users’ trip from their perspective, especially for the first mile and the last mile of their trip. The intensive commuter survey is currently being done at selected stations to gain information of their first mile and last mile trip diary. Discriminant analysis will be exercised to explain that to some extent online ojek is able to work to fill the gap produced due to minimum proper pedestrian facilities and a lack of public transport connection.

INTERMODAL TRANSPORT IN EUROPE - OPPORTUNITIES THROUGH INNOVATION

Directory of Open Access Journals (Sweden)

Norbert Wagener

2014-12-01

Full Text Available Background: Freight transport volume in ton-km in OECD countries will grow considerably up to 150 to 230 % in 2050 compared to 2010. Although the EU policy aims to shift 30% of road freight over 300 km to other modes such as rail or waterborne transport by 2030 the recent trends show a stable modal split of road at approx. 75%. Conventional intermodal transport on the major European routes has shown a steady but only limited organic growth through recent years. Therefore, new innovative concepts for intermodal transport and for the shift from road to rail are needed. Methods: Definitions of intermodal transport have been clarified and the development of combined transport in Europe and in Germany and Poland in particular has been analyzed on the basis of available data sources. New innovative concepts for intermodal transport have been identified on the basis of desk research, recent relevant projects (RETRACK, SCANDRIA, Rail Baltica and market intelligence. Results: The analysis leads to the conclusion that new innovative concepts in intermodal transport comprise new forms of organization as well as new technologies and new routes. The following three innovations to facilitate the shift from road to rail by intermodal transport are being introduced and discussed: multimodal operation of ocean carriers in maritime hinterland transportation, innovative handling technologies for non-crane able trainers and freight corridors for long distance intermodal transport within the TEN-T network and on the Europe-Asia corridor. Conclusions: Further accelerated growth in the shift from road to rail through intermodal transport requires new innovative concepts beyond the traditional combined transport in Western Europe. Three promising innovative concepts have been introduced. Further research is needed and should be focused on financial and economic appraisal as well as on the effectiveness of state intervention policies. 

Simply rails 2 the ultimate beginner's guide to Ruby on rails

CERN Document Server

Lenz, Patrick

2008-01-01

Want to learn all about Ruby on Rails 2.0, the web application framework that is inspiring developers around the world? The second edition of this practical, hands on book will: show you how to install Ruby on Rails on Windows, Mac, or Linux walk you, step by step, through the development of a Web 2.0 social news application, just like digg.com show you how to test, debug, benchmark, and deploy your Rails application Unlike other Rails books, this book doesn't assume that you are an experienced web developer, or that you've used Ruby before. An entire chapter is devoted to learning Ruby in a fun way, using the interactive Ruby console, so you can follow along at home. You'll be an accomplished Ruby programmer in no time! The example application that the book builds - a user-generated news web site - is built upon with each following chapter, and concepts such as sessions, cookies and basic AJAX usage are gradually introduced. Different aspects of Rails, such as user authentication, session cookies, and automa...

49 CFR 213.235 - Inspection of switches, track crossings, and lift rail assemblies or other transition devices on...

Science.gov (United States)

2010-10-01

... rail assemblies or other transition devices on moveable bridges. 213.235 Section 213.235 Transportation... assemblies or other transition devices on moveable bridges. (a) Except as provided in paragraph (c) of this section, each switch, turnout, track crossing, and moveable bridge lift rail assembly or other transition...

Discrete multi-physics simulations of diffusive and convective mass transfer in boundary layers containing motile cilia in lungs.

Science.gov (United States)

Ariane, Mostapha; Kassinos, Stavros; Velaga, Sitaram; Alexiadis, Alessio

2018-04-01

In this paper, the mass transfer coefficient (permeability) of boundary layers containing motile cilia is investigated by means of discrete multi-physics. The idea is to understand the main mechanisms of mass transport occurring in a ciliated-layer; one specific application being inhaled drugs in the respiratory epithelium. The effect of drug diffusivity, cilia beat frequency and cilia flexibility is studied. Our results show the existence of three mass transfer regimes. A low frequency regime, which we called shielding regime, where the presence of the cilia hinders mass transport; an intermediate frequency regime, which we have called diffusive regime, where diffusion is the controlling mechanism; and a high frequency regime, which we have called convective regime, where the degree of bending of the cilia seems to be the most important factor controlling mass transfer in the ciliated-layer. Since the flexibility of the cilia and the frequency of the beat changes with age and health conditions, the knowledge of these three regimes allows prediction of how mass transfer varies with these factors. Copyright © 2018 Elsevier Ltd. All rights reserved.

Optical Properties of Plasmon Resonances with Ag/SiO2/Ag Multi-Layer Composite Nanoparticles

International Nuclear Information System (INIS)

Ye-Wan, Ma; Li-Hua, Zhang; Zhao-Wang, Wu; Jie, Zhang

2010-01-01

Optical properties of plasmon resonance with Ag/SiO 2 /Ag multi-layer nanoparticles are studied by numerical simulation based on Green's function theory. The results show that compared with single-layer Ag nanoparticles, the multi-layer nanoparticles exhibit several distinctive optical properties, e.g. with increasing the numbers of the multi-layer nanoparticles, the scattering efficiency red shifts, and the intensity of scattering enhances accordingly. It is interesting to find out that slicing an Ag-layer into multi-layers leads to stronger scattering intensity and more 'hot spots' or regions of stronger field enhancement. This property of plasmon resonance of surface Raman scattering has greatly broadened the application scope of Raman spectroscopy. The study of metal surface plasmon resonance characteristics is critical to the further understanding of surface enhanced Raman scattering as well as its applications. (fundamental areas of phenomenology (including applications))

Regulation on the transport of nuclear fuel materials by vehicles

International Nuclear Information System (INIS)

1984-01-01

The regulations applying to the transport of nuclear fuel materials by vehicles, mentioned in the law for the regulations of nuclear source materials, nuclear fuel materials and reactors. The transport is for outside of the factories and the site of enterprises by such modes of transport as rail, trucks, etc. Covered are the following: definitions of terms, places of fuel materials handling, loading methods, limitations on mix loading with other cargo, radiation dose rates concerning the containers and the vehicles, transport indexes, signs and indications, limitations on train linkage during transport by rail, security guards, transport of empty containers, etc. together with ordinary rail cargo and so on. (Mori, K.)

Effects of profile wear on wheel–rail contact conditions and dynamic interaction of vehicle and turnout

Directory of Open Access Journals (Sweden)

Jingmang Xu

2016-01-01

Full Text Available Severe wear is a common damage mechanism in railway turnouts, which strongly affects the dynamic performance of railway vehicles and maintenance costs of tracks. This article explores the effects of profile wear on contact behaviors in the wheel–rail/switch contact and dynamic interaction, and nominal and measured worn turnout rail profiles are used as boundary conditions of wheel–rail contact. The calculation of the dynamic loads and the resultant contact stresses and internal stresses makes it possible to rationally design railway turnouts and correctly select the material to be applied for their components. For these reasons, the multi-body system SIMPACK and finite element software ANSYS are used to calculate the features of load and subsequently distributions of contact stresses and internal stresses in the regions of wheel–turnout components. The results show that profile wear disturbs the distribution of wheel–rail contact point pairs, changes the positions of wheel–rail contact points along the longitudinal direction, and affects the dynamic interaction of vehicle and turnout. For the measured profile in this article, profile wear aggravates vertical dynamic responses significantly but improves lateral dynamic responses. Profile wear disturbs the normal contact situations between the wheel and switch rail and worsens the stress state of the switch rail.

A review on fuzzy and stochastic extensions of the multi index transportation problem

Directory of Open Access Journals (Sweden)

Singh Sungeeta

2017-01-01

Full Text Available The classical transportation problem (having source and destination as indices deals with the objective of minimizing a single criterion, i.e. cost of transporting a commodity. Additional indices such as commodities and modes of transport led to the Multi Index transportation problem. An additional fixed cost, independent of the units transported, led to the Multi Index Fixed Charge transportation problem. Criteria other than cost (such as time, profit etc. led to the Multi Index Bi-criteria transportation problem. The application of fuzzy and stochastic concept in the above transportation problems would enable researchers to not only introduce real life uncertainties but also obtain solutions of these transportation problems. The review article presents an organized study of the Multi Index transportation problem and its fuzzy and stochastic extensions till today, and aims to help researchers working with complex transportation problems.

Heterojunction PbS nanocrystal solar cells with oxide charge-transport layers.

Science.gov (United States)

Hyun, Byung-Ryool; Choi, Joshua J; Seyler, Kyle L; Hanrath, Tobias; Wise, Frank W

2013-12-23

Oxides are commonly employed as electron-transport layers in optoelectronic devices based on semiconductor nanocrystals, but are relatively rare as hole-transport layers. We report studies of NiO hole-transport layers in PbS nanocrystal photovoltaic structures. Transient fluorescence experiments are used to verify the relevant energy levels for hole transfer. On the basis of these results, planar heterojunction devices with ZnO as the photoanode and NiO as the photocathode were fabricated and characterized. Solution-processed devices were used to systematically study the dependence on nanocrystal size and achieve conversion efficiency as high as 2.5%. Optical modeling indicates that optimum performance should be obtained with thinner oxide layers than can be produced reliably by solution casting. Room-temperature sputtering allows deposition of oxide layers as thin as 10 nm, which enables optimization of device performance with respect to the thickness of the charge-transport layers. The best devices achieve an open-circuit voltage of 0.72 V and efficiency of 5.3% while eliminating most organic material from the structure and being compatible with tandem structures.

Rail inspection of RCF defects

Directory of Open Access Journals (Sweden)

Z. Popović

2013-10-01

Full Text Available Rail defects due to rolling contact fatigue (RCF threaten the traffic safety around the world. That hazard is more distinct on railways without adequate maintenance strategy. Realization of interoperability of European railway network demands from every infrastructure manager to have a maintenance plan for the infrastructure subsystem. Besides that, this plan includes rail inspection and strategy against RCF defects. This paper emphasizes the importance of rail inspection and early detection of RCF because the most of RCF crack should be removed in rail grinding campaigns (preventive, cyclical and corrective activities during the whole rail service life.

Fatigue crack growth monitoring in multi-layered structures using guided ultrasonic waves

International Nuclear Information System (INIS)

Kostson, E; Fromme, P

2009-01-01

This contribution investigates the application of low frequency guided ultrasonic waves for monitoring fatigue crack growth at fastener holes in the 2nd layer of multi-layered plate structures, a common problem in aerospace industry. The model multi-layered structure investigated consists of two aluminum plate-strips adhesively bonded using a structural paste adhesive. Guided ultrasonic waves were excited using multiple piezoelectric discs bonded to the surface of the multi-layered structure. The wave propagation in the tensile specimen was measured using a laser interferometer and compared to numerical simulations. Thickness and width mode shapes of the excited flexural waves were identified from Semi-Analytical Finite Element (SAFE) calculations. Experiments and 3D Finite Element (FE) simulations show a change in the scattered field around fastener holes caused by a defect in the 2nd layer. The amplitude of the guided ultrasonic wave was monitored during fatigue experiments at a single point. The measured changes in the amplitude of the ultrasonic signal due to fatigue crack growth agree well with FE simulations.

Ordinance on the Carriage of Dangerous Goods by Rail (GGVE). 2. rev. and enl. ed.

International Nuclear Information System (INIS)

Ridder, K.; Katholnig, F.

1993-01-01

The book presents the legislative texts and other legal provisions concerning the transport of dangerous goods by rail: (1) Act on the transport of dangerous goods, full text. (2) Ordinance on the carriage of dangerous goods by rail (GGVE) - GGVE skeleton ordinance; Annex to the skeleton ordinance. (3) Documents - GGVE implementing regulations RE 001; R 002; Ordinance on exeptions GGVE; Extracts from IAEA recommendations concerning safe transport of radioactive materials; catalogue of fines pertaining to section 10 GGVE. (4) Alphabetical list of materials for GGVE/RID and GGVS/ADR. Index terms printed in deep black at the margin of pages allow quick access to the text passages of interest, and there is a subject index for retrieval over the entire book. (orig./HP) [de

Elastic Buckling Behaviour of General Multi-Layered Graphene Sheets

Directory of Open Access Journals (Sweden)

Rong Ming Lin

2015-04-01

Full Text Available Elastic buckling behaviour of multi-layered graphene sheets is rigorously investigated. Van der Waals forces are modelled, to a first order approximation, as linear physical springs which connect the nodes between the layers. Critical buckling loads and their associated modes are established and analyzed under different boundary conditions, aspect ratios and compressive loading ratios in the case of graphene sheets compressed in two perpendicular directions. Various practically possible loading configurations are examined and their effect on buckling characteristics is assessed. To model more accurately the buckling behaviour of multi-layered graphene sheets, a physically more representative and realistic mixed boundary support concept is proposed and applied. For the fundamental buckling mode under mixed boundary support, the layers with different boundary supports deform similarly but non-identically, leading to resultant van der Waals bonding forces between the layers which in turn affect critical buckling load. Results are compared with existing known solutions to illustrate the excellent numerical accuracy of the proposed modelling approach. The buckling characteristics of graphene sheets presented in this paper form a comprehensive and wholesome study which can be used as potential structural design guideline when graphene sheets are employed for nano-scale sensing and actuation applications such as nano-electro-mechanical systems.

Optimization of sound absorbing performance for gradient multi-layer-assembled sintered fibrous absorbers

Science.gov (United States)

Zhang, Bo; Zhang, Weiyong; Zhu, Jian

2012-04-01

The transfer matrix method, based on plane wave theory, of multi-layer equivalent fluid is employed to evaluate the sound absorbing properties of two-layer-assembled and three-layer-assembled sintered fibrous sheets (generally regarded as a kind of compound absorber or structures). Two objective functions which are more suitable for the optimization of sound absorption properties of multi-layer absorbers within the wider frequency ranges are developed and the optimized results of using two objective functions are also compared with each other. It is found that using the two objective functions, especially the second one, may be more helpful to exert the sound absorbing properties of absorbers at lower frequencies to the best of their abilities. Then the calculation and optimization of sound absorption properties of multi-layer-assembled structures are performed by developing a simulated annealing genetic arithmetic program and using above-mentioned objective functions. Finally, based on the optimization in this work the thoughts of the gradient design over the acoustic parameters- the porosity, the tortuosity, the viscous and thermal characteristic lengths and the thickness of each samples- of porous metals are put forth and thereby some useful design criteria upon the acoustic parameters of each layer of porous fibrous metals are given while applying the multi-layer-assembled compound absorbers in noise control engineering.

A survey of wheel-rail contact models for rail vehicles

Science.gov (United States)

Meymand, Sajjad Z.; Keylin, Alexander; Ahmadian, Mehdi

2016-03-01

Accurate and efficient contact models for wheel-rail interaction are essential for the study of the dynamic behaviour of a railway vehicle. Assessment of the contact forces and moments, as well as contact geometry provide a fundamental foundation for such tasks as design of braking and traction control systems, prediction of wheel and rail wear, and evaluation of ride safety and comfort. This paper discusses the evolution and the current state of the theories for solving the wheel-rail contact problem for rolling stock. The well-known theories for modelling both normal contact (Hertzian and non-Hertzian) and tangential contact (Kalker's linear theory, FASTSIM, CONTACT, Polach's theory, etc.) are reviewed. The paper discusses the simplifying assumptions for developing these models and compares their functionality. The experimental studies for evaluation of contact models are also reviewed. This paper concludes with discussing open areas in contact mechanics that require further research for developing better models to represent the wheel-rail interaction.

On efficiently computing multigroup multi-layer neutron reflection and transmission conditions

International Nuclear Information System (INIS)

Abreu, Marcos P. de

2007-01-01

In this article, we present an algorithm for efficient computation of multigroup discrete ordinates neutron reflection and transmission conditions, which replace a multi-layered boundary region in neutron multiplication eigenvalue computations with no spatial truncation error. In contrast to the independent layer-by-layer algorithm considered thus far in our computations, the algorithm here is based on an inductive approach developed by the present author for deriving neutron reflection and transmission conditions for a nonactive boundary region with an arbitrary number of arbitrarily thick layers. With this new algorithm, we were able to increase significantly the computational efficiency of our spectral diamond-spectral Green's function method for solving multigroup neutron multiplication eigenvalue problems with multi-layered boundary regions. We provide comparative results for a two-group reactor core model to illustrate the increased efficiency of our spectral method, and we conclude this article with a number of general remarks. (author)

Preparation of multi-layer film consisting of hydrogen-free DLC and nitrogen-containing DLC for conductive hard coating

Science.gov (United States)

Iijima, Yushi; Harigai, Toru; Isono, Ryo; Degai, Satoshi; Tanimoto, Tsuyoshi; Suda, Yoshiyuki; Takikawa, Hirofumi; Yasui, Haruyuki; Kaneko, Satoru; Kunitsugu, Shinsuke; Kamiya, Masao; Taki, Makoto

2018-01-01

Conductive hard-coating films have potential application as protective films for contact pins used in the electrical inspection process for integrated circuit chips. In this study, multi-layer diamond-like carbon (DLC) films were prepared as conductive hard-coating films. The multi-layer DLC films consisting of DLC and nitrogen-containing DLC (N-DLC) film were prepared using a T-shape filtered arc deposition method. Periodic DLC/N-DLC four-layer and eight-layer films had the same film thickness by changing the thickness of each layer. In the ball-on-disk test, the N-DLC mono-layer film showed the highest wear resistance; however, in the spherical polishing method, the eight-layer film showed the highest polishing resistance. The wear and polishing resistance and the aggressiveness against an opponent material of the multi-layer DLC films improved by reducing the thickness of a layer. In multi-layer films, the soft N-DLC layer between hard DLC layers is believed to function as a cushion. Thus, the tribological properties of the DLC films were improved by a multi-layered structure. The electrical resistivity of multi-layer DLC films was approximately half that of the DLC mono-layer film. Therefore, the periodic DLC/N-DLC eight-layer film is a good conductive hard-coating film.

Truck and rail charges for shipping spent fuel and nuclear waste

International Nuclear Information System (INIS)

McNair, G.W.; Cole, B.M.; Cross, R.E.; Votaw, E.F.

1986-06-01

The Pacific Northwest Laboratory developed techniques for calculating estimates of nuclear-waste shipping costs and compiled a listing of representative data that facilitate incorporation of reference shipping costs into varius logistics analyses. The formulas that were developed can be used to estimate costs that will be incurred for shipping spent fuel or nuclear waste by either legal-weight truck or general-freight rail. The basic data for this study were obtained from tariffs of a truck carrier licensed to serve the 48 contiguous states and from various rail freight tariff guides. Also, current transportation regulations as issued by the US Department of Transportation and the Nuclear Regulatory Commission were investigated. The costs that will be incurred for shipping spent fuel and/or nuclear waste, as addressed by the tariff guides, are based on a complex set of conditions involving the shipment origin, route, destination, weight, size, and volume and the frequency of shipments, existing competition, and the length of contracts. While the complexity of these conditions is an important factor in arriving at a ''correct'' cost, deregulation of the transportation industry means that costs are much more subject to negotiation and, thus, the actual fee that will be charged will not be determined until a shipping contract is actually signed. This study is designed to provide the baseline data necessary for making comparisons of the estimated costs of shipping spent fuel and/or nuclear wastes by truck and rail transportation modes. The scope of the work presented in this document is limited to the costs incurred for shipping, and does not include packaging, cask purchase/lease costs, or local fees placed on shipments of radioactive materials

Performance criteria for EM rail launchers with solid or transition armatures and laminated rails

International Nuclear Information System (INIS)

James, T.E.

1991-01-01

Velocity limitations of EM Rail Launchers with solid armatures due to the velocity skin-effect are assessed for a range of homogeneous materials (copper, aluminium, molybdenum and tungsten). Performance criteria as limited by armature melting in the region adjacent to the rail/armature contact surface and by rail surface melting are deduced analytically based on defined electro-thermal reference conditions. The performance criteria predict the reference transition velocity at which the solid contact surface changes to mainly a melted contact surface which is shown to be a fundamental property of the materials. The paper shows that the critical factors in obtaining a high transition velocity are a relatively high resistivity armature material combined with high temperature rail surface coatings. For example a transition velocity of >2.0 km/s for a molybdenum armature and a tungsten rail surface coating on a copper rail are predicted compared with <0.5 km/s for the aluminium/copper combination frequently used

Investigation of the residue in an electric rail gun employing a plasma armature

Science.gov (United States)

Bauer, D. P.; Barber, J. P.

1984-01-01

The performance of dc electric rail guns using plasma-armature-accelerated projectiles was studied. It was found that the initial rail launcher acceleration profile was consistent with the simulation, but that after the projectile had traveled approximately 25 to 30 cm along the gun, a considerable portion of the current in the projectile armature commutated into a secondary current path. Also noted were the lower than expected muzzle velocities. It was proposed that the secondary current path was a relatively high conductivity layer of residue on the launcher bore.

Stationary Charging Station Design for Sustainable Urban Rail Systems: A Case Study at Zhuzhou Electric Locomotive Co., China

Directory of Open Access Journals (Sweden)

Heng Li

2015-01-01

Full Text Available In 2014, more than 43 cities in China were racing to construct their urban rail systems (including metro and light rail systems, recognizing that an urban rail system will be a good solution to the tough problems that they are faced with, including traffic congestion and PM2.5 air pollution. On 22 August 2012, the first electric double-layer capacitor (EDLC energy storage-type rail vehicle in the world was unveiled at Zhuzhou Electric Locomotive Co., China. The EDLC rail system has been considered a promising sustainable urban rail system, which is expected to further improve the energy efficiency and to reduce environmental pollution. The first commercial EDLC tram produced by Zhuzhou Electric Locomotive Co. has been applied at Guangzhou Metro Corp. recently. From the view point of scientific research, the system design and energy management of EDLC rail systems have been extensively studied in the literature, while the stationary charging station design for the EDLC energy storage-type urban rail vehicles has been rarely reported. Thus, the aim of this paper is to report a stationary charging station that has been successfully applied in the EDLC rail system produced by Zhuzhou Electric Locomotive Co., China.

Transport package maintenance requirements and operations

International Nuclear Information System (INIS)

Tyacke, M.J.; Ball, L.J.; Ayers, A.L. Jr.; Hayes, G.R.; Anselmo, A.A.

1988-01-01

The NuPac 125-B rail cask, which transports the damaged core debris from Three Mile Island Unit 2 (TMI-2) to the Idaho National Engineering Laboratory (INEL), is the only new spent-fuel rail shipping cask to be licensed in the United States within the last decade. EG ampersand G Idaho, Inc. (EG ampersand G), acting on behalf of the US Department of Energy, is responsible for ensuring that those new casks and rail cars are properly maintained per regulatory requirements. Both the casks and rail cars have comprehensive in-service inspection and preventive maintenance programs, which are more involved than implied by the requirements. The TMI-2 shipping campaign is the most ambitious spent-fuel transport activity being conducted in the nuclear industry. The experience gained in this campaign, as it relates to maintenance of a transport system, should be of interest and have direct applicability to similar shipping activities planned in the years ahead

Multi-type particle layer improved light trapping for photovoltaic applications

DEFF Research Database (Denmark)

David, Christin

2016-01-01

. The absorbance was enhanced compared to the bare Si wafer and I demonstrated on mixing particles a broadband boost in the absorbance within the homogeneous wafer region, excluding parasitic absorption in the particle layer. I studied the efficiency enhancement for varying geometries. Multi-type layers made of Si...

A manufacturing method for multi-layer polysilicon surface-micromachining technology

Energy Technology Data Exchange (ETDEWEB)

Sniegowski, J.J.; Rodgers, M.S.

1998-01-01

An advanced manufacturing technology which provides multi-layered polysilicon surface micromachining technology for advanced weapon systems is presented. Specifically, the addition of another design layer to a 4 levels process to create a 5 levels process allows consideration of fundamentally new architecture in designs for weapon advanced surety components.

CargoMover - the driverless 'truck on rails'; CargoMover - der fahrerlose 'Lkw auf Schienen'

Energy Technology Data Exchange (ETDEWEB)

Mairhofer, F. [Siemens AG, Erlangen (Germany). Transportation Systems, Cargo Logistics; Janssen, G. [DB Netz AG, NL West, Duisburg (Germany)

2003-07-01

Year after year, more and more freight is transported in Europe. Most of it is transported by road, because users currently see the truck as the fastest, most flexible and most economic solution. But road haulage is already leading to a lot of congestion, so that is it becoming more and more important to shift traffic onto the railways. The high-availability CargoMover {sup registered} system complements existing rail freight transport services. It combines the strategic advantages of truck and rail transport and offers flexible driverless rail freight transport to individual destinations - including at regional and local level, and for short-term requirements or small loads. (orig.) [German] Jahr fuer Jahr werden in Europa mehr Gueter bewegt. Der Grossteil dieser Transporte erfolgt auf der Strasse, weil der LKW von vielen Nutzern momentan als die schnellste, flexibelste und wirtschaftlichste Loesung angesehen wird. Schon heute fuehrt der Lkw-Verkehr aber zu vielen Staus, so dass es immer wichtiger wird, mehr Transportvolumen auf die Schiene zu bringen. Der CargoMover {sup registered} komplettiert als hochverfuegbares System das Gueterverkehrsangebot auf der Schiene. Er verbindet die strategischen Vorteile des Lkw mit denen des Bahnsystems und ermoeglicht fahrerlosen, zielreinen und flexiblen Gueterverkehr auf der Schiene - auch im Regional- und Nahverkehr, bei kurzfristigem Bedarf oder kleineren Losgroessen. (orig.)

Application of Multi-Layered Polyurethane Foams for Flat-Walled Anechoic Linings

DEFF Research Database (Denmark)

Xu, J. F.; Buchholz, Jörg; Fricke, Fergus R.

2006-01-01

of the application of multi-layered polyurethane foams as the flat-walled anechoic lining. The investigation includes aspects such as the efficacy of a single layer of material, the minimum number of layers of linings to achieve the minimum overall thickness for low (100Hz), mid (250Hz) and high (500Hz) cut...

Heterojunction PbS Nanocrystal Solar Cells with Oxide Charge-Transport Layers

KAUST Repository

Hyun, Byung-Ryool

2013-12-23

Oxides are commonly employed as electron-transport layers in optoelectronic devices based on semiconductor nanocrystals, but are relatively rare as hole-transport layers. We report studies of NiO hole-transport layers in PbS nanocrystal photovoltaic structures. Transient fluorescence experiments are used to verify the relevant energy levels for hole transfer. On the basis of these results, planar heterojunction devices with ZnO as the photoanode and NiO as the photocathode were fabricated and characterized. Solution-processed devices were used to systematically study the dependence on nanocrystal size and achieve conversion efficiency as high as 2.5%. Optical modeling indicates that optimum performance should be obtained with thinner oxide layers than can be produced reliably by solution casting. Roomerature sputtering allows deposition of oxide layers as thin as 10 nm, which enables optimization of device performance with respect to the thickness of the charge-transport layers. The best devices achieve an open-circuit voltage of 0.72 V and efficiency of 5.3% while eliminating most organic material from the structure and being compatible with tandem structures. © 2013 American Chemical Society.

Spectroscopic characterization of ion-irradiated multi-layer graphenes

Energy Technology Data Exchange (ETDEWEB)

Tsukagoshi, Akira [Graduate School of Engineering, University of Hyogo, Himeji, Hyogo 671-2280 (Japan); RIKEN SPring-8 Center, Sayo, Hyogo 679-5148 (Japan); Honda, Shin-ichi, E-mail: s-honda@eng.u-hyogo.ac.jp [Graduate School of Engineering, University of Hyogo, Himeji, Hyogo 671-2280 (Japan); RIKEN SPring-8 Center, Sayo, Hyogo 679-5148 (Japan); Osugi, Ryo [Graduate School of Engineering, University of Hyogo, Himeji, Hyogo 671-2280 (Japan); RIKEN SPring-8 Center, Sayo, Hyogo 679-5148 (Japan); Okada, Hiraku [Graduate School of Engineering, University of Hyogo, Himeji, Hyogo 671-2280 (Japan); Niibe, Masahito [Laboratory of Advanced Science and Technology for Industry, University of Hyogo, Kamigori, Hyogo 678-1205 (Japan); Terasawa, Mititaka [Laboratory of Advanced Science and Technology for Industry, University of Hyogo, Kamigori, Hyogo 678-1205 (Japan); RIKEN SPring-8 Center, Sayo, Hyogo 679-5148 (Japan); Hirase, Ryuji; Izumi, Hirokazu; Yoshioka, Hideki [Hyogo Prefectural Institute of Technology, Kobe 654-0037 (Japan); Niwase, Keisuke [Hyogo University of Teacher Education, Kato, Hyogo 673-1494 (Japan); Taguchi, Eiji [Research Center for Ultra-High Voltage Electron Microscopy, Osaka University, Ibaraki, Osaka 567-0047 (Japan); Lee, Kuei-Yi [Department of Electronic Engineering, National Taiwan University of Science and Technology, Taipei 106, Taiwan (China); Oura, Masaki [RIKEN SPring-8 Center, Sayo, Hyogo 679-5148 (Japan)

2013-11-15

Low-energy Ar ions (0.5–2 keV) were irradiated to multi-layer graphenes and the damage process, the local electronic states, and the degree of alignment of the basal plane, and the oxidation process upon ion irradiation were investigated by Raman spectroscopy, soft X-ray absorption spectroscopy (XAS) and in situ X-ray photoelectron spectroscopy (XPS). By Raman spectroscopy, we observed two stages similar to the case of irradiated graphite, which should relate to the accumulations of vacancies and turbulence of the basal plane, respectively. XAS analysis indicated that the number of sp{sup 2}-hybridized carbon (sp{sup 2}-C) atoms decreased after ion irradiation. Angle-resolved XAS revealed that the orientation parameter (OP) decreased with increasing ion energy and fluence, reflecting the turbulence of the basal plane under irradiation. In situ XPS shows the oxidation of the irradiated multi-layer graphenes after air exposure.

46 CFR 169.329 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Storm rails. 169.329 Section 169.329 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Construction and Arrangement Rails and Guards § 169.329 Storm rails. Suitable storm rails or hand grabs must be...

Environmental Impacts of Transportation to the Potential Repository at Yucca Mountain

International Nuclear Information System (INIS)

Sweeney, R.L.; Best, R.; Bolton, P.; Adams, P.

2002-01-01

The Environmental Impact Statement for a Geologic Repository for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain, Nye County, Nevada analyzes a Proposed Action to construct, operate, monitor, and eventually close a geologic repository for the disposal of spent nuclear fuel and high-level radioactive waste. As part of the Proposed Action, the EIS analyzes the potential impacts of transporting commercial and DOE spent nuclear fuel and high-level radioactive waste to Yucca Mountain from 77 sites across the United States. The analysis includes information on the comparative impacts of transporting these materials by truck and rail and discusses the impacts of building a rail line or using heavy-haul trucks to move rail casks from a mainline railroad in Nevada to the site. This paper provides an overview of the analyses and the potential impacts of these transportation activities. The potential transportation impacts were looked at from two perspectives: transportation of spent nuclear fuel and high-level radioactive waste by legal-weight truck or by rail on a national scale and impacts specific to Nevada from the transportation of these materials from the State borders to the Yucca Mountain site. In order to address the range of impacts that could result from the most likely modes, legal-weight truck and rail, the EIS employed two analytical scenarios--mostly legal-weight truck and mostly rail. Estimated national transportation impacts were based on 24 years of transportation activities. Approximately 8 fatalities could occur from all causes in the nationwide general population from incident-free transportation activities of the mostly legal-weight truck scenario and about 4 from the mostly rail scenario. The analysis examined the radiological consequences under the maximum foreseeable accident scenario and also overall accident risk. The overall accident risk over the 24 year period would be about 0.0002 latent cancer fatality for

Non-localized deformation in Cu−Zr multi-layer amorphous films under tension

Energy Technology Data Exchange (ETDEWEB)

Zhong, C. [International Center for New-Structured Materials (ICNSM), Laboratory of New-Structured Materials, State Key Laboratory of Silicon Materials, and School of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Zhang, H. [International Center for New-Structured Materials (ICNSM), Laboratory of New-Structured Materials, State Key Laboratory of Silicon Materials, and School of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Department of Chemical and Materials Engineering, University of Alberta, Edmonton, Alberta T6G 1H9 (Canada); Cao, Q.P.; Wang, X.D. [International Center for New-Structured Materials (ICNSM), Laboratory of New-Structured Materials, State Key Laboratory of Silicon Materials, and School of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Zhang, D.X. [State Key Laboratory of Modern Optical Instrumentation, Zhejiang University, Hangzhou 310027 (China); Hu, J.W. [Hangzhou Workers Amateur University, Hangzhou 310027 (China); Liaw, P.K. [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996 (United States); Jiang, J.Z., E-mail: jiangjz@zju.edu.cn [International Center for New-Structured Materials (ICNSM), Laboratory of New-Structured Materials, State Key Laboratory of Silicon Materials, and School of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China)

2016-09-05

In metallic glasses (MGs), plastic deformation at room temperature is dominated by highly localized shear bands. Here we report the non-localized deformation under tension in Cu−Zr multi-layer MGs with a pure amorphous structure using large-scale atomistic simulations. It is demonstrated that amorphous samples with high layer numbers, composed of Cu{sub 64}Zr{sub 36} and Cu{sub 40}Zr{sub 60}, or Cu{sub 64}Zr{sub 36} and Cu{sub 50}Zr{sub 50}, present obviously non-localized deformation behavior. We reveal that the deformation behavior of the multi-layer-structured MG films is related but not determined by the deformation behavior of the composed individual layers. The criterion for the deformation mode change for MGs with a pure amorphous structure, in generally, was suggested, i.e., the competition between the elastic-energy density stored and the energy density needed for forming one mature shear band in MGs. Our results provide a promising strategy for designing tensile ductile MGs with a pure amorphous structure at room temperature. - Highlights: • Tensile deformation behaviors in multi-layer MG films. • Films with high layer numbers confirmed with a non-localized deformation behavior. • The deformation mode is reasonably controlled by whether U{sub p} larger than U{sub SB.}.

The impact of Pulpwood Rail Freight Costs on the Minnesota-Wisconsin Pulpwood Market

Science.gov (United States)

David C. Lothner

1976-01-01

Transportation costs affect the marketing and utilization of pulpwood. Their impact on the procurement and utilization of pulpwood often prove difficult to measure because deriving an average annual measure of the transportation cost is difficult. This note, by means of a simple index method for measuring regional interstate pulpwood rail freight costs, illustrates...

High conductivity and transparent aluminum-based multi-layer source/drain electrodes for thin film transistors

Science.gov (United States)

Yao, Rihui; Zhang, Hongke; Fang, Zhiqiang; Ning, Honglong; Zheng, Zeke; Li, Xiaoqing; Zhang, Xiaochen; Cai, Wei; Lu, Xubing; Peng, Junbiao

2018-02-01

In this study, high conductivity and transparent multi-layer (AZO/Al/AZO-/Al/AZO) source/drain (S/D) electrodes for thin film transistors were fabricated via conventional physical vapor deposition approaches, without toxic elements or further thermal annealing process. The 68 nm-thick multi-layer films with excellent optical properties (transparency: 82.64%), good electrical properties (resistivity: 6.64  ×  10-5 Ω m, work function: 3.95 eV), and superior surface roughness (R q   =  0.757 nm with scanning area of 5  ×  5 µm2) were fabricated as the S/D electrodes. Significantly, comprehensive performances of AZO films are enhanced by the insertion of ultra-thin Al layers. The optimal transparent TFT with this multi-layer S/D electrodes exhibited a decent electrical performance with a saturation mobility (µ sat) of 3.2 cm2 V-1 s-1, an I on/I off ratio of 1.59  ×  106, a subthreshold swing of 1.05 V/decade. The contact resistance of AZO/Al/AZO/Al/AZO multi-layer electrodes is as low as 0.29 MΩ. Moreover, the average visible light transmittance of the unpatterned multi-layers constituting a whole transparent TFT could reach 72.5%. The high conductivity and transparent multi-layer S/D electrodes for transparent TFTs possessed great potential for the applications of the green and transparent displays industry.

Multi-bits memory cell using degenerated magnetic states in a synthetic antiferromagnetic reference layer

International Nuclear Information System (INIS)

Fukushima, Akio; Yakushiji, Kay; Konoto, Makoto; Kubota, Hitoshi; Imamura, Hiroshi; Yuasa, Shinji

2016-01-01

We newly developed a magnetic memory cell having multi-bit function. The memory cell composed of a perpendicularly magnetized magnetic tunnel junction (MB-pMTJ) and a synthetic antiferromagnetic reference layer. The multi-bit function is realized by combining the freedom of states of the magnetic free layer and that in the antiferromagnetically coupled reference layer. The structure of the reference layer is (FeB/Ta/[Co/Pt]_3)/Ru/([Co/Pt]_6); the top and the bottom layers are coupled through Ru layer where the reference layer has two degrees of freedom of a head-to-head and a bottom-to-bottom magnetic configuration. A four-state memory cell is realized by combination of both degrees of freedom. The states in the reference layer however is hardly detected by the total resistance of MB-pMTJ, because the magnetoresistance effect in the reference layer is negligibly small. That implies that the resistance values for the different states in the reference layer are degenerated. On the other hand, the two different states in the reference layer bring different stray fields to the free layer, which generate two different minor loop with different switching fields. Therefore, the magnetic states in the reference layer can be differentiated by the two-step reading, before and after applying the appropriately pulsed magnetic field which can identify the initial state in the reference layer. This method is similar to distinguishing different magnetic states in an in-plane magnetized spin-valve element. We demonstrated that four different states in the MB-pMTJ can be distinguished by the two-step read-out. The important feature of the two-step reading is a practically large operation margins (large resistance change in reading) which is equal to that of a single MTJ. Even though the two-step reading is a destructive method by which 50% of the magnetic state is changed, this MB-pMTJ is promising for high density non-volatile memory cell with a minor cost of operation speed

46 CFR 177.920 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Storm rails. 177.920 Section 177.920 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) CONSTRUCTION AND ARRANGEMENT Rails and Guards § 177.920 Storm rails. Suitable storm rails or hand grabs must be...

46 CFR 127.320 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Storm rails. 127.320 Section 127.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS CONSTRUCTION AND ARRANGEMENTS Rails and Guards § 127.320 Storm rails. Suitable storm rails must be installed in each passageway and at...

Multi-layer hierarchical array fabricated with diatom frustules for highly sensitive bio-detection applications

International Nuclear Information System (INIS)

Li, Aobo; Cai, Jun; Pan, Junfeng; Wang, Yu; Yue, Yue; Zhang, Deyuan

2014-01-01

Diatoms have delicate porous structures which are very beneficial in improving the absorbing ability in the bio-detection field. In this study, multi-layered hierarchical arrays were fabricated by packing Nitzschia soratensis (N. soratensis) frustules into Cosinodiscus argus (C. argus) frustules to achieve advanced sensitivity in bio-detection chips. Photolithographic patterning was used to obtain N. soratensis frustule arrays, and the floating behavior of C. argus frustules was employed to control their postures for packing N. soratensis frustule array spots. The morphology of the multi-layer C. argus–N. soratensis package array was investigated by scanning electron microscopy, demonstrating that the overall and sub-structures of the diatom frustules were retained. The signal enhancing effect of multi-layer C. argus–N. soratensis packages was demonstrated by fluorescent antibody test results. The mechanism of the enhancement was also analyzed, indicating that both complex hierarchical frustule structures and optimized posture of C. argus frustules were important for improving bio-detection sensitivities. The technique for fabricating multi-layer diatom frustules arrays is also useful for making multi-functional biochips and controllable drug delivery systems. (paper)

78 FR 10581 - Rail Vehicles Access Advisory Committee

Science.gov (United States)

2013-02-14

... guideway systems (e.g., rapid rail, light rail, commuter rail, and intercity rail). We are establishing a... vehicles that operate on fixed guideway systems (e.g., rapid rail, light rail, commuter rail, and intercity... for their service. We may pay travel expenses for a limited number of persons who would otherwise be...

Coherent Network Optimizing of Rail-Based Urban Mass Transit

Directory of Open Access Journals (Sweden)

Ying Zhang

2012-01-01

Full Text Available An efficient public transport is more than ever a crucial factor when it comes to the quality of life and competitiveness of many cities and regions in Asia. In recent years, the rail-based urban mass transit has been regarded as one of the key means to overcoming the great challenges in Chinese megacities. The purpose of this study is going to develop a coherent network optimizing for rail-based urban mass transit to find the best alternatives for the user and to demonstrate how to meet sustainable development needs and to match the enormous capacity requirements simultaneously. This paper presents an introduction to the current situation of the important lines, and transfer points in the metro system Shanghai. The insufficient aspects are analyzed and evaluated; while the optimizing ideas and measurements are developed and concreted. A group of examples are used to illustrate the approach. The whole study could be used for the latest reference for other megacities which have to be confronted with the similar situations and processes with enormous dynamic travel and transport demands.

46 CFR 108.221 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Storm rails. 108.221 Section 108.221 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Construction and Arrangement Rails § 108.221 Storm rails. Each unit must have a storm rail in the following...

Analysis of an optimal public transport structure under a carbon emission constraint: a case study in Shanghai, China.

Science.gov (United States)

Zhang, Linling; Long, Ruyin; Chen, Hong; Yang, Tong

2018-02-01

Along with the rapid development of the transportation industry, the problems of the energy crisis and transport emissions have become increasingly serious. The success of traffic emission reduction is related to the realization of global low-carbon goals. Placing priority on public transport is the internationally recognized traffic development model. This paper takes Shanghai, China, as an example to examine the optimal public transport structure. Five factors were selected from personal and public perspectives, including travel costs, crowding degree, occupied area, traffic emissions, and operating subsidies. The objective functions of these factors were transformed into satisfaction functions, and a multi-objective programming model was used to solve for the optimal proportions of the ground bus and rail transit, and the carbon emission reduction potential was analyzed in different scenarios. The study showed that the actual proportion of rail transit in Shanghai was slightly lower than the optimal value, and accompanied by low satisfaction with each factor relative to the optimal value. It was difficult to achieve the traffic emission reduction targets by only reducing satisfaction with other factors except carbon emissions assuming a fixed proportion of public transport. As the proportion of total travel represented by public transport increased, rail transit became the main mode of public transport and the usage trend was more obvious, but the structure of public transport gradually reached a relatively stable state after a certain level of development. Compared to reducing carbon emissions by changing satisfaction with other factors, it was easier to achieve traffic emission reduction targets by increasing the proportion of public transport. To increase the proportion of public transport travel and achieve the goal of traffic reduction in the future, further improvements are needed in the quality of public transport system services, public transport

Self-similar solutions for multi-species plasma mixing by gradient driven transport

Science.gov (United States)

Vold, E.; Kagan, G.; Simakov, A. N.; Molvig, K.; Yin, L.

2018-05-01

Multi-species transport of plasma ions across an initial interface between DT and CH is shown to exhibit self-similar species density profiles under 1D isobaric conditions. Results using transport theory from recent studies and using a Maxwell–Stephan multi-species approximation are found to be in good agreement for the self-similar mix profiles of the four ions under isothermal and isobaric conditions. The individual ion species mass flux and molar flux profile results through the mixing layer are examined using transport theory. The sum over species mass flux is confirmed to be zero as required, and the sum over species molar flux is related to a local velocity divergence needed to maintain pressure equilibrium during the transport process. The light ion species mass fluxes are dominated by the diagonal coefficients of the diffusion transport matrix, while for the heaviest ion species (C in this case), the ion flux with only the diagonal term is reduced by about a factor two from that using the full diffusion matrix, implying the heavy species moves more by frictional collisions with the lighter species than by its own gradient force. Temperature gradient forces were examined by comparing profile results with and without imposing constant temperature gradients chosen to be of realistic magnitude for ICF experimental conditions at a fuel-capsule interface (10 μm scale length or greater). The temperature gradients clearly modify the relative concentrations of the ions, for example near the fuel center, however the mixing across the fuel-capsule interface appears to be minimally influenced by the temperature gradient forces within the expected compression and burn time. Discussion considers the application of the self-similar profiles to specific conditions in ICF.

Multi-scale modelling and numerical simulation of electronic kinetic transport

International Nuclear Information System (INIS)

Duclous, R.

2009-11-01

This research thesis which is at the interface between numerical analysis, plasma physics and applied mathematics, deals with the kinetic modelling and numerical simulations of the electron energy transport and deposition in laser-produced plasmas, having in view the processes of fuel assembly to temperature and density conditions necessary to ignite fusion reactions. After a brief review of the processes at play in the collisional kinetic theory of plasmas, with a focus on basic models and methods to implement, couple and validate them, the author focuses on the collective aspect related to the free-streaming electron transport equation in the non-relativistic limit as well as in the relativistic regime. He discusses the numerical development and analysis of the scheme for the Vlasov-Maxwell system, and the selection of a validation procedure and numerical tests. Then, he investigates more specific aspects of the collective transport: the multi-specie transport, submitted to phase-space discontinuities. Dealing with the multi-scale physics of electron transport with collision source terms, he validates the accuracy of a fast Monte Carlo multi-grid solver for the Fokker-Planck-Landau electron-electron collision operator. He reports realistic simulations for the kinetic electron transport in the frame of the shock ignition scheme, the development and validation of a reduced electron transport angular model. He finally explores the relative importance of the processes involving electron-electron collisions at high energy by means a multi-scale reduced model with relativistic Boltzmann terms

A fracture mechanics assessment of surface cracks existing in protective layers of multi-layer composite pipes

Czech Academy of Sciences Publication Activity Database

Hutař, Pavel; Náhlík, Luboš; Šestáková, Lucie; Ševčík, Martin; Knésl, Zdeněk; Nezbedová, E.

2010-01-01

Roč. 92, č. 5 (2010), s. 1120-1125 ISSN 0263-8223 R&D Projects: GA ČR GA106/09/0279 Institutional research plan: CEZ:AV0Z20410507 Keywords : Protective layers * Multi-layer pipes damage * Fracture mechanics * Bi-material interface * Generalized stress intensity factor Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 2.028, year: 2010

Multi-layer enhancement to polysilicon surface-micromachining technology

Energy Technology Data Exchange (ETDEWEB)

Sniegowski, J.J.; Rodgers, M.S. [Sandia National Labs., Albuquerque, NM (United States). Intelligent Micromachine Dept.

1997-10-01

A multi-level polysilicon surface-micromachining technology consisting of 5 layers of polysilicon is presented. Surface topography and film mechanical stress are the major impediments encountered in the development of a multilayer surface-micromachining process. However, excellent mechanical film characteristics have been obtained through the use of chemical-mechanical polishing for planarization of topography and by proper sequencing of film deposition with thermal anneals. Examples of operating microactuators, geared power-transfer mechanisms, and optical elements demonstrate the mechanical advantages of construction with 5 polysilicon layers.

Journal of transportation engineering

National Research Council Canada - National Science Library

1983-01-01

The Journal of Transportation Engineering contains technical and professional articles on the planning, design, construction, maintenance, and operation of air, highway, rail, and urban transportation...

Rail-to-rail low-power fully differential OTA utilizing adaptive biasing and partial feedback

DEFF Research Database (Denmark)

Tuan Vu, Cao; Wisland, Dag T.; Lande, Tor Sverre

A fully differential rail-to-rail Operational Transconductance Amplifier (OTA) with improved DC-gain and reduced power consumption is proposed in this paper. By using the adaptive biasing circuit and two differential inputs, a low stand-by current can be obtained together with reduced power...... consumption. The DC-gain of the proposed OTA is improved by adding a partial feedback loop. A Common-Mode Feedback (CMFB) circuit is required for fully differential rail-to-rail operation. Simulations show that the OTA topology has a low stand-by power consumption of 96μW and a high FoM of 3.84 [(V...

Characterization of the morphology of co-extruded, thermoplastic/rubber multi-layer tapes

International Nuclear Information System (INIS)

L'Abee, R.M.A.; Vissers, A.M.J.T.; Goossens, J.G.P.; Spoelstra, A.B.; Duin, M. van

2009-01-01

Tapes with alternating semi-crystalline thermoplastic/rubber layers with thicknesses varying from 100 nm up to several μm were prepared by multi-layer co-extrusion. The variation in layer thickness was obtained by varying the thermoplastic/rubber feed ratio. A systematic study on the use of various microscopy techniques to visualize the morphology of the layered systems is presented. The relatively large length scales and the sample preparation make optical microscopy (OM) unsuitable to study the morphology of the multi-layer tapes. Although excellent contrast between the thermoplastic and rubber layers can be obtained, the usually applied, relatively large magnifications limit the use of transmission electron microscopy (TEM) and atomic force microscopy (AFM) to small sample areas. The large range of applicable magnifications makes scanning electron microscopy (SEM) the most suitable technique to study the morphology of the multi-layer tapes. The sample preparation for SEM with a secondary electron (SE) detector is often based on the removal of one of the components, which may induce changes in the morphology. SEM with a back-scattered electron (BSE) detector is a very convenient method to study the morphology over a wide range of length scales, where the contrast between the different layers can be enhanced by chemical staining. Finally, the nucleation behavior (homogeneous versus heterogeneous) of the semi-crystalline layers, as probed by differential scanning calorimetry (DSC), provides valuable information on the layered morphology. The use of relatively straightforward DSC measurements shows a clear advantage with respect to the discussed microscopy techniques, since no sample preparation is required and relatively large samples can be studied, which are more representative for the bulk.

78 FR 66326 - Hazardous Materials: Rail Petitions and Recommendations To Improve the Safety of Railroad Tank...

Science.gov (United States)

2013-11-05

...: Rail Petitions and Recommendations To Improve the Safety of Railroad Tank Car Transportation (RRR) AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: Advance Notice of... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Parts...

Nevada potential repository preliminary transportation strategy: Study 1

Energy Technology Data Exchange (ETDEWEB)

None,

1995-04-01

Limited feasible options exist when considering the shipment of spent nuclear fuel and high-level radioactive waste. These options are rail or truck; because of the weight associated with transportation casks (68.0 to 113.4 tonnes/75 to 125 tons), heavy-haul trucks are also considered. Yucca Mountain currently lacks rail service or an existing right-of-way for rail; it also lacks a dedicated highway suitable for heavy-haul trucks. Approximately 11,230 shipments by rail are planned from waste producer sites to Nevada, with an additional 1,041 shipments by legal-weight truck from four reactor sites not capable of upgrading for rail shipment. This study identifies the reasonable alternatives for waste transport to the potential repository site, describes the evaluation process performed to identify those alternatives, and discusses the reasons for elimination of transportation routes deemed to be not reasonable. The study concluded that heavy haul truck transportation is feasible-cost is very favorable when compared to rail-but route restrictions must be further evaluated. In addition to restrictions due to seasonal weather conditions, specific routes have additional restrictions, including no travel on holidays or weekends, and travel during daylight hours only. Further restrictions will be imposed by the U.S. Department of Transportation based on routing of radioactive materials by highway. Operation and maintenance costs for heavy-haul over a 24-year period, based on preliminary information, were calculated on an estimated operational cost of $15,000 per trip, with an estimated 468 trips per year average (11,230 total trips), for an estimated cost of $171 million to $173 million, depending on the route used. Because the initial costs and the total system life cycle costs of heavy-haul are approximately 50 percent lower than the lowest rail cost, this option will continue to be evaluated.

Nevada potential repository preliminary transportation strategy: Study 1

International Nuclear Information System (INIS)

1995-04-01

Limited feasible options exist when considering the shipment of spent nuclear fuel and high-level radioactive waste. These options are rail or truck; because of the weight associated with transportation casks (68.0 to 113.4 tonnes/75 to 125 tons), heavy-haul trucks are also considered. Yucca Mountain currently lacks rail service or an existing right-of-way for rail; it also lacks a dedicated highway suitable for heavy-haul trucks. Approximately 11,230 shipments by rail are planned from waste producer sites to Nevada, with an additional 1,041 shipments by legal-weight truck from four reactor sites not capable of upgrading for rail shipment. This study identifies the reasonable alternatives for waste transport to the potential repository site, describes the evaluation process performed to identify those alternatives, and discusses the reasons for elimination of transportation routes deemed to be not reasonable. The study concluded that heavy haul truck transportation is feasible-cost is very favorable when compared to rail-but route restrictions must be further evaluated. In addition to restrictions due to seasonal weather conditions, specific routes have additional restrictions, including no travel on holidays or weekends, and travel during daylight hours only. Further restrictions will be imposed by the U.S. Department of Transportation based on routing of radioactive materials by highway. Operation and maintenance costs for heavy-haul over a 24-year period, based on preliminary information, were calculated on an estimated operational cost of $15,000 per trip, with an estimated 468 trips per year average (11,230 total trips), for an estimated cost of $171 million to $173 million, depending on the route used. Because the initial costs and the total system life cycle costs of heavy-haul are approximately 50 percent lower than the lowest rail cost, this option will continue to be evaluated

Multi-layer protective armour for underwater shock wave mitigation

Directory of Open Access Journals (Sweden)

Ahmed Hawass

2015-12-01

The strain gauge data and displacement sensors results showed that the multi-layer plates have higher level of underwater shock wave mitigation than the triple aluminum plates with strain and deflection of nearly 50%.

Radioactive contamination level of vehicles resulted from transporting fine rare-earth minerals by rail

International Nuclear Information System (INIS)

Han Kaichun; Yu Boyong; Gao Shengwei

1997-01-01

This paper presents monitoring results of radioactive contamination level of steel open wagon surface resulted from transporting fine rare-earth minerals. Under promising transport conditions (the packaging consists of two layers of plastic bags and two layers of plastic net sacks, each package contains 50 kg of minerals, each vehicle carries 60 t), the surface radioactivity (total α and total β) of 16 vehicles on two lines from Baotou to Wujiachuan (924 km) and from Baotou to Sankeshu (2236 km) was measured before loading, after unloading and washing, using α and β surface contamination detector. The results showed that the radioactive contamination level of the vehicle surface after unloading appeared significantly different. The contamination level of vehicle bases was higher than that of both sides, long distance vehicles was higher than that of short distance vehicles. The radioactive contamination level of vehicles surface after washing was below the standard limits, these vehicles can be used for ordinary goods transport

Transport of oxide spent fuel. Industrial experience of COGEMA

International Nuclear Information System (INIS)

Lenail, B.

1983-01-01

COGEMA is ruling all transports of spent fuel to La Hague reprocessing plant. The paper summarizes some aspects of the experience gained in this field (road, rail and sea transports) and describes the standards defined by COGEMA as regards transport casks. These standards are as follows: - casks of dry type, - casks of the maximum size compatible with rail transports, - capability to be unloaded with standardized equipment and following standard procedures

Cost that is Directly Incurred as a Result of Operating the Train Service on the 1520 mm Rail with Primarily Freight Transportation

OpenAIRE

Hudenko, J; Ribakova, N; Počs, R

2016-01-01

Under the Directive 2012/34/EU (21 November 2012) "the charges for … [rail] infrastructure … shall be set at the cost that is directly incurred as a result of operating the train service". This charging rule is new for Baltic States’ railways, where due to the favorable geographic position a full cost application without detalization was possible. Although, a big number of relevant studies on the issue was made in EU, all of them covered only 1435mm railways with primarily passenger transport...

Effect of antiferromagnetic interfacial coupling on spin-wave resonance frequency of multi-layer film

Energy Technology Data Exchange (ETDEWEB)

Qiu, Rong-ke, E-mail: rkqiu@163.com; Cai, Wei

2017-08-15

Highlights: • A quantum approach is developed to study the SWR of a bicomponent multi-layer films. • The comparison of the SWR in films with FM and AFM interfacial coupling has been made. • The present results show the method to enhance and adjust the SWR frequency of films. - Abstract: We investigate the spin-wave resonance (SWR) frequency in a bicomponent bilayer and triple-layer films with antiferromagnetic or ferromagnetic interfacial couplings, as function of interfacial coupling, surface anisotropy, interface anisotropy, thickness and external magnetic field, using the linear spin-wave approximation and Green’s function technique. The microwave properties for multi-layer magnetic film with antiferromagnetic interfacial coupling is different from those for multi-layer magnetic film with ferromagnetic interfacial coupling. For the bilayer film with antiferromagnetic interfacial couplings, as the lower (upper) surface anisotropy increases, only the SWR frequencies of the odd (even) number modes increase. The lower (upper) surface anisotropy does not affect the SWR frequencies of the even (odd) number modes{sub .} For the multi-layer film with antiferromagnetic interfacial coupling, the SWR frequency of modes m = 1, 3 and 4 decreases while that of mode m = 2 increases with increasing thickness of the film within a proper parameter region. The present results could be useful in enhancing our fundamental understanding and show the method to enhance and adjust the SWR frequency of bicomponent multi-layer magnetic films with antiferromagnetic or ferromagnetic interfacial coupling.

Bio-Inspired Multi-Functional Drug Transport Design Concept and Simulations.

Science.gov (United States)

Pidaparti, Ramana M; Cartin, Charles; Su, Guoguang

2017-04-25

In this study, we developed a microdevice concept for drug/fluidic transport taking an inspiration from supramolecular motor found in biological cells. Specifically, idealized multi-functional design geometry (nozzle/diffuser/nozzle) was developed for (i) fluidic/particle transport; (ii) particle separation; and (iii) droplet generation. Several design simulations were conducted to demonstrate the working principles of the multi-functional device. The design simulations illustrate that the proposed design concept is feasible for multi-functionality. However, further experimentation and optimization studies are needed to fully evaluate the multifunctional device concept for multiple applications.

Taxonomy-driven adaptation of multi-layer applications using templates

OpenAIRE

Popescu, Razvan; Staikopoulos, Athanasios; Liu, Peng; Brogi, Antonio; Clarke, Siobh??n

2010-01-01

peer-reviewed Current adaptation approaches mainly work in isolation and cannot be easily integrated to tackle complex adaptation scenarios. The few existing cross-layer adaptation techniques are somewhat inflexible because the adaptation process is predefined and static. In this paper we propose a methodology for the dynamic and flexible adaptation of multi-layer applications. We use events to trigger the process of matching adaptation templates, which expose adaptation logic as BPEL pro...

High-speed rail with emerging automobiles and aircraft can reduce environmental impacts in California’s future

International Nuclear Information System (INIS)

Chester, Mikhail; Horvath, Arpad

2012-01-01

Sustainable mobility policy for long-distance transportation services should consider emerging automobiles and aircraft as well as infrastructure and supply chain life-cycle effects in the assessment of new high-speed rail systems. Using the California corridor, future automobiles, high-speed rail and aircraft long-distance travel are evaluated, considering emerging fuel-efficient vehicles, new train designs and the possibility that the region will meet renewable electricity goals. An attributional per passenger-kilometer-traveled life-cycle inventory is first developed including vehicle, infrastructure and energy production components. A consequential life-cycle impact assessment is then established to evaluate existing infrastructure expansion against the construction of a new high-speed rail system. The results show that when using the life-cycle assessment framework, greenhouse gas footprints increase significantly and human health and environmental damage potentials may be dominated by indirect and supply chain components. The environmental payback is most sensitive to the number of automobile trips shifted to high-speed rail, and for greenhouse gases is likely to occur in 20–30 years. A high-speed rail system that is deployed with state-of-the-art trains, electricity that has met renewable goals, and in a configuration that endorses high ridership will provide significant environmental benefits over existing modes. Opportunities exist for reducing the long-distance transportation footprint by incentivizing large automobile trip shifts, meeting clean electricity goals and reducing material production effects. (letter)

Determination of rail wear and short-time wear measurements of rails applying radioisotopes

International Nuclear Information System (INIS)

Grohmann, H.D.

1981-01-01

An energetic model has been developed for calculating rail wear. Short-time wear tests on rails after surface activation and following activity measurements showed a good agreement with the calculated values

Study on tribological properties of multi-layer surface texture on Babbitt alloys surface

Science.gov (United States)

Zhang, Dongya; Zhao, Feifei; Li, Yan; Li, Pengyang; Zeng, Qunfeng; Dong, Guangneng

2016-12-01

To improve tribological properties of Babbitt alloys, multi-layer surface texture consisted of the main grooves and secondary micro-dimples are fabricated on the Babbitt substrate through laser pulse ablation. The tribological behaviors of multi-layer surface texture are investigated using a rotating type pin-on-disc tribo-meter under variation sliding speeds, and the film pressure distributions on the textured surfaces are simulated using computational fluid dynamics (CFD) method for elucidating the possible mechanisms. The results suggest that: (i) the multi-layer surface texture can reduce friction coefficient of Babbitt alloy, which has lowest friction coefficient of 0.03, in case of the groove parameter of 300 μm width and 15% of area density; (ii) the improvement effect may be more sensitive to the groove area density and the siding speed, and the textured surface with lower area density has lower friction coefficient under high sliding speed. Based on the reasons of (i) the secondary micro-dimples on Babbitt alloy possesses a hydrophobicity surface and (ii) the CFD analysis indicates that main grooves enhancing hydrodynamic effect, thus the multi-layer surface texture is regarded as dramatically improve the lubricating properties of the Babbitt alloy.

Cross-Dependency Inference in Multi-Layered Networks: A Collaborative Filtering Perspective.

Science.gov (United States)

Chen, Chen; Tong, Hanghang; Xie, Lei; Ying, Lei; He, Qing

2017-08-01

The increasingly connected world has catalyzed the fusion of networks from different domains, which facilitates the emergence of a new network model-multi-layered networks. Examples of such kind of network systems include critical infrastructure networks, biological systems, organization-level collaborations, cross-platform e-commerce, and so forth. One crucial structure that distances multi-layered network from other network models is its cross-layer dependency, which describes the associations between the nodes from different layers. Needless to say, the cross-layer dependency in the network plays an essential role in many data mining applications like system robustness analysis and complex network control. However, it remains a daunting task to know the exact dependency relationships due to noise, limited accessibility, and so forth. In this article, we tackle the cross-layer dependency inference problem by modeling it as a collective collaborative filtering problem. Based on this idea, we propose an effective algorithm Fascinate that can reveal unobserved dependencies with linear complexity. Moreover, we derive Fascinate-ZERO, an online variant of Fascinate that can respond to a newly added node timely by checking its neighborhood dependencies. We perform extensive evaluations on real datasets to substantiate the superiority of our proposed approaches.

Optoelectronic devices, low temperature preparation methods, and improved electron transport layers

KAUST Repository

Eita, Mohamed S.; El, Labban Abdulrahman; Usman, Anwar; Beaujuge, Pierre; Mohammed, Omar F.

2016-01-01

An optoelectronic device such as a photovoltaic device which has at least one layer, such as an electron transport layer, which comprises a plurality of alternating, oppositely charged layers including metal oxide layers. The metal oxide can be zinc

Co-transport of chlordecone and sulfadiazine in the presence of functionalized multi-walled carbon nanotubes in soils.

Science.gov (United States)

Zhang, Miaoyue; Engelhardt, Irina; Šimůnek, Jirka; Bradford, Scott A; Kasel, Daniela; Berns, Anne E; Vereecken, Harry; Klumpp, Erwin

2017-02-01

Batch and saturated soil column experiments were conducted to investigate sorption and mobility of two 14 C-labeled contaminants, the hydrophobic chlordecone (CLD) and the sulfadiazine (SDZ), in the absence or presence of functionalized multi-walled carbon nanotubes (MWCNTs). The transport behaviors of CLD, SDZ, and MWCNTs were studied at environmentally relevant concentrations (0.1-10 mg L -1 ) and they were applied in the column studies at different times. The breakthrough curves and retention profiles were simulated using a numerical model that accounted for the advective-dispersive transport of all compounds, attachment/detachment of MWCNTs, equilibrium and kinetic sorption of contaminants, and co-transport of contaminants with MWCNTs. The experimental results indicated that the presence of mobile MWCNTs facilitated remobilization of previously deposited CLD and its co-transport into deeper soil layers, while retained MWCNTs enhanced SDZ deposition in the topsoil layers due to the increased adsorption capacity of the soil. The modeling results then demonstrated that the mobility of engineered nanoparticles (ENPs) in the environment and the high affinity and entrapment of contaminants to ENPs were the main reasons for ENP-facilitated contaminant transport. On the other hand, immobile MWCNTs had a less significant impact on the contaminant transport, even though they were still able to enhance the adsorption capacity of the soil. Copyright © 2016 Elsevier Ltd. All rights reserved.

Optoelectronic transport properties in amorphous/crystalline silicon solar cell heterojunctions measured by frequency-domain photocarrier radiometry: Multi-parameter measurement reliability and precision studies

International Nuclear Information System (INIS)

Zhang, Y.; Melnikov, A.; Mandelis, A.; Halliop, B.; Kherani, N. P.; Zhu, R.

2015-01-01

A theoretical one-dimensional two-layer linear photocarrier radiometry (PCR) model including the presence of effective interface carrier traps was used to evaluate the transport parameters of p-type hydrogenated amorphous silicon (a-Si:H) and n-type crystalline silicon (c-Si) passivated by an intrinsic hydrogenated amorphous silicon (i-layer) nanolayer. Several crystalline Si heterojunction structures were examined to investigate the influence of the i-layer thickness and the doping concentration of the a-Si:H layer. The experimental data of a series of heterojunction structures with intrinsic thin layers were fitted to PCR theory to gain insight into the transport properties of these devices. The quantitative multi-parameter results were studied with regard to measurement reliability (uniqueness) and precision using two independent computational best-fit programs. The considerable influence on the transport properties of the entire structure of two key parameters that can limit the performance of amorphous thin film solar cells, namely, the doping concentration of the a-Si:H layer and the i-layer thickness was demonstrated. It was shown that PCR can be applied to the non-destructive characterization of a-Si:H/c-Si heterojunction solar cells yielding reliable measurements of the key parameters

Optoelectronic transport properties in amorphous/crystalline silicon solar cell heterojunctions measured by frequency-domain photocarrier radiometry: multi-parameter measurement reliability and precision studies.

Science.gov (United States)

Zhang, Y; Melnikov, A; Mandelis, A; Halliop, B; Kherani, N P; Zhu, R

2015-03-01

A theoretical one-dimensional two-layer linear photocarrier radiometry (PCR) model including the presence of effective interface carrier traps was used to evaluate the transport parameters of p-type hydrogenated amorphous silicon (a-Si:H) and n-type crystalline silicon (c-Si) passivated by an intrinsic hydrogenated amorphous silicon (i-layer) nanolayer. Several crystalline Si heterojunction structures were examined to investigate the influence of the i-layer thickness and the doping concentration of the a-Si:H layer. The experimental data of a series of heterojunction structures with intrinsic thin layers were fitted to PCR theory to gain insight into the transport properties of these devices. The quantitative multi-parameter results were studied with regard to measurement reliability (uniqueness) and precision using two independent computational best-fit programs. The considerable influence on the transport properties of the entire structure of two key parameters that can limit the performance of amorphous thin film solar cells, namely, the doping concentration of the a-Si:H layer and the i-layer thickness was demonstrated. It was shown that PCR can be applied to the non-destructive characterization of a-Si:H/c-Si heterojunction solar cells yielding reliable measurements of the key parameters.

Influence of the Radiation Shield on the Temperature of Rails Rolled in the Reversing Mill

Directory of Open Access Journals (Sweden)

Gołdasz A.

2015-04-01

Full Text Available The paper presents a mathematical model of heat transfer during cooling of hot-rolled rails in the reversing mill. The influence of the radiation shield on the temperature of rolled rails has been analyzed. The heat transfer model for cooling a strip covered by the thermal shield has been presented. The two types of shields build of steel and aluminum sheets separated with insulating layer have been studded. Calculations have been performed with self developed software which utilizes the finite element method.

49 CFR Appendix D to Part 172 - Rail Risk Analysis Factors

Science.gov (United States)

2010-10-01

...(s) and route(s) being analyzed, the analysis must provide a thorough description of the threats... during all stages of transportation. C. Because of the varying operating environments and interconnected nature of the rail system, each carrier must select and document the analysis method/model used and...

Active current management for four-rail railguns

International Nuclear Information System (INIS)

Beno, J.H.; Weldon, W.F.

1991-01-01

In this paper a system of auxiliary conductors designed to reduce current density peaks in railgun rails for four-rail, round-bore railguns is described. The effects on rail current density and projectile force are discussed. Railgun cross-sectional designs are presented for round-bore, four-rail railguns which operate at lower peak current densities and develop greater projectile forces than conventional two-rail, round-bore railguns

Real-Time Transportation Mode Identification Using Artificial Neural Networks Enhanced with Mode Availability Layers: A Case Study in Dubai

Directory of Open Access Journals (Sweden)

Young-Ji Byon

2017-09-01

Full Text Available Traditionally, departments of transportation (DOTs have dispatched probe vehicles with dedicated vehicles and drivers for monitoring traffic conditions. Emerging assisted GPS (AGPS and accelerometer-equipped smartphones offer new sources of raw data that arise from voluntarily-traveling smartphone users provided that their modes of transportation can correctly be identified. By introducing additional raster map layers that indicate the availability of each mode, it is possible to enhance the accuracy of mode detection results. Even in its simplest form, an artificial neural network (ANN excels at pattern recognition with a relatively short processing timeframe once it is properly trained, which is suitable for real-time mode identification purposes. Dubai is one of the major cities in the Middle East and offers unique environments, such as a high density of extremely high-rise buildings that may introduce multi-path errors with GPS signals. This paper develops real-time mode identification ANNs enhanced with proposed mode availability geographic information system (GIS layers, firstly for a universal mode detection and, secondly for an auto mode detection for the particular intelligent transportation system (ITS application of traffic monitoring, and compares the results with existing approaches. It is found that ANN-based real-time mode identification, enhanced by mode availability GIS layers, significantly outperforms the existing methods.

Rail projects gather steam

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-01-15

The global recession hit rail companies hard, as demand for bulk commodities such as coal was affected. But green shoots of recovery are now appearing, with many rail companies announcing new haulage contracts. 3 figs.

Silicon transport in sputter-deposited tantalum layers grown under ion bombardment

International Nuclear Information System (INIS)

Gallais, P.; Hantzpergue, J.J.; Remy, J.C.; Roptin, D.

1988-01-01

Tantalum was sputter deposited on (111) Si substrate under low-energy ion bombardment in order to study the effects of the ion energy on the silicon transport into the Ta layer. The Si substrate was heated up to 500 0 C during growth. For ion energies up to 180 eV silicon is not transported into tantalum and the growth temperature has no effect. An ion bombardment energy of 280 eV enhances the transport of silicon throughout the tantalum layer. Growth temperatures up to 300 0 C have no effect on the silicon transport which is mainly enhanced by the ion bombardment. For growth temperatures between 300 and 500 0 C, the silicon transport is also enhanced by the thermal diffusion. The experimental depth distribution of silicon is similar to the theoretical depth distribution calculated for the case of an interdiffusion. The ion-enhanced process of silicon transport is characterized by an activation energy of 0.4 eV. Silicon into the layers as-grown at 500 0 C is in both states, amorphous silicide and microcrystalline cubic silicon

Heating of multi-layered samples by a Nd: YAG pulsed laser

International Nuclear Information System (INIS)

Diniz Neto, O.O.

1998-01-01

In the work we examine the heating of multi-layered samples by a powerful Nd-YAG pulsed laser. The samples are made of two and three layers, conductor-isolator (Al-Al 2 O 3 ). conductor-conductor (Al-Ag: Al-Au) an conductor-conductor-conductor (Al-Au-Ag:Ag-Au-Al). The transient behaviour of the temperature distribution throughout the samples is computed. We carry out three dimensional model calculations for the heating process in which we consider not only the temperature dependence of the sample thermal and optical parameters but also the space and time characteristics of the laser beams as the heating source. We showed the influence of the substrate in the thermal profile, in space and time, and maximum temperature on the multi-layered samples. (Author) 11 refs

Turbulent transport in the atmospheric surface layer

Energy Technology Data Exchange (ETDEWEB)

Tagesson, Torbern [Dept. of Physical Geography and Ecosystem Science, Lund Univ., Lund (Sweden)

2012-04-15

In the modelling of transport and accumulation of the radioactive isotope carbon-14 (C-14) in the case of a potential release from a future repository of radioactive waste, it is important to describe the transport of the isotope in the atmosphere. This report aims to describe the turbulent transport within the lower part of the atmosphere; the inertial surface layer and the roughness sublayer. Transport in the inertial surface layer is dependent on several factors, whereof some can be neglected under certain circumstances. Under steady state conditions, fully developed turbulent conditions, in flat and horizontal homogeneous areas, it is possible to apply an eddy diffusivity approach for estimating vertical transport of C. The eddy diffusivity model assumes that there is proportionality between the vertical gradient and the transport of C. The eddy diffusivity is depending on the atmospheric turbulence, which is affected by the interaction between mean wind and friction of the ground surface and of the sensible heat flux in the atmosphere. In this report, it is described how eddy diffusivity of the inertial surface layer can be estimated from 3-d wind measurements and measurements of sensible heat fluxes. It is also described how to estimate the eddy diffusivity in the inertial surface layer from profile measurements of temperature and wind speed. Close to the canopy, wind and C profiles are influenced by effects of the surface roughness; this section of the atmosphere is called the roughness sublayer. Its height is up to {approx}3 times the height of the plant canopy. When the mean wind interacts with the canopy, turbulence is not only produced by shear stress and buoyancy, it is additionally created by wakes, which are formed behind the plants. Turbulence is higher than it would be over a flat surface, and the turbulent transport is hereby more efficient. Above the plant canopy, but still within the roughness sublayer, a function that compensates for the effect

Turbulent transport in the atmospheric surface layer

International Nuclear Information System (INIS)

Tagesson, Torbern

2012-04-01

In the modelling of transport and accumulation of the radioactive isotope carbon-14 (C-14) in the case of a potential release from a future repository of radioactive waste, it is important to describe the transport of the isotope in the atmosphere. This report aims to describe the turbulent transport within the lower part of the atmosphere; the inertial surface layer and the roughness sublayer. Transport in the inertial surface layer is dependent on several factors, whereof some can be neglected under certain circumstances. Under steady state conditions, fully developed turbulent conditions, in flat and horizontal homogeneous areas, it is possible to apply an eddy diffusivity approach for estimating vertical transport of C. The eddy diffusivity model assumes that there is proportionality between the vertical gradient and the transport of C. The eddy diffusivity is depending on the atmospheric turbulence, which is affected by the interaction between mean wind and friction of the ground surface and of the sensible heat flux in the atmosphere. In this report, it is described how eddy diffusivity of the inertial surface layer can be estimated from 3-d wind measurements and measurements of sensible heat fluxes. It is also described how to estimate the eddy diffusivity in the inertial surface layer from profile measurements of temperature and wind speed. Close to the canopy, wind and C profiles are influenced by effects of the surface roughness; this section of the atmosphere is called the roughness sublayer. Its height is up to ∼3 times the height of the plant canopy. When the mean wind interacts with the canopy, turbulence is not only produced by shear stress and buoyancy, it is additionally created by wakes, which are formed behind the plants. Turbulence is higher than it would be over a flat surface, and the turbulent transport is hereby more efficient. Above the plant canopy, but still within the roughness sublayer, a function that compensates for the effect of

Transportation Energy Futures Series: Freight Transportation Modal Shares: Scenarios for a Low-Carbon Future

Energy Technology Data Exchange (ETDEWEB)

Brogan, J. J.; Aeppli, A. E.; Beagan, D. F.; Brown, A.; Fischer, M. J.; Grenzeback, L. R.; McKenzie, E.; Vimmerstedt, L.; Vyas, A. D.; Witzke, E.

2013-03-01

Truck, rail, water, air, and pipeline modes each serve a distinct share of the freight transportation market. The current allocation of freight by mode is the product of technologic, economic, and regulatory frameworks, and a variety of factors -- price, speed, reliability, accessibility, visibility, security, and safety -- influence mode. Based on a comprehensive literature review, this report considers how analytical methods can be used to project future modal shares and offers insights on federal policy decisions with the potential to prompt shifts to energy-efficient, low-emission modes. There are substantial opportunities to reduce the energy used for freight transportation, but it will be difficult to shift large volumes from one mode to another without imposing considerable additional costs on businesses and consumers. This report explores federal government actions that could help trigger the shifts in modal shares needed to reduce energy consumption and emissions. This is one in a series of reports produced as a result of the Transportation Energy Futures project, a Department of Energy-sponsored multi-agency effort to pinpoint underexplored strategies for reducing GHGs and petroleum dependence related to transportation.

Experiences with radiation portal detectors for international rail transport

International Nuclear Information System (INIS)

Stromswold, David C.; McCormick, Kathleen R.; Todd, Lindsay C.; Ashbaker, Eric D.; Evans, J.C.

2006-01-01

Radiation detectors monitored trains at two international borders to evaluate the performance of NaI(Tl) and plastic (polyvinyltoluene: PVT) gamma-ray detectors to characterize rail cargo. The detectors included a prototype NaI(Tl) radiation-portal-monitor panel having four large detectors (10-cm x 10-cm x 41-cm) and a PVT panel with a 41 cm x 173 cm x 3.8-cm detector. Spectral data from the NaI(Tl) and PVT detectors were recorded. Of particular emphasis was the identification of naturally occurring radioactive material (NORM) and the resultant frequency of nuisance alarms. For rail monitoring, the difficulty in stopping trains to perform secondary inspection on alarming cars creates a need for reliable identification of NORM during initial screening. Approximately 30 trains were monitored, and the commodities in individual railcars were ascertained from manifest information. At one test site the trains carried inter-modal containers that had been unloaded from ships, and at the other site the trains contained bulk cargo or individual items in boxcars or flatbeds. NORM encountered included potash, liquefied petroleum gas, fireworks, televisions, and clay-based products (e.g., pottery). Analysis of the spectral data included the use of the template-fitting program GADRAS/FitToDB from Sandia National Laboratories. For much of the NORM the NaI(Tl) data produced a correct identification of the radionuclides present in the railcars. The same analysis was also used for PVT data in which the spectral information (no peaks but only gradual spectral changes including Compton edges) was limited. However, the PVT analysis provided correct identification of 40K and 226Ra in many cases

Multi-layered satisficing decision making in oil and gas production platforms

DEFF Research Database (Denmark)

Lindegaard Mikkelsen, Lars; Demazeau, Yves; Jørgensen, B. N.

2013-01-01

From a control perspective, offshore oil and gas production is very challenging due to the many and potentially conflicting production objectives that arise from the intrinsic complexity of the oil and gas domain. In this paper, we show how a multi-layered multi-agent system can be used to implem...

Rail base corrosion and cracking prevention

Science.gov (United States)

2014-07-01

Rail base corrosion combined with fatigue or damage can significantly reduce rail life. Studies were done to examine the relative contribution of damage, corrosion, and fatigue on rail life. The combined effects can be separated into constituent fact...

Optimal thickness of hole transport layer in doped OLEDs