Actinide partitioning-transmutation program final report. III. Transmutation studies

International Nuclear Information System (INIS)

Wachter, J.W.; Croff, A.G.

1980-07-01

Transmutation of the long-lived nuclides contained in fuel cycle wastes has been suggested as a means of reducing the long-term toxicity of the wastes. A comprehensive program to evaluate the feasibility and incentives for recovering the actinides from wastes (partitioning) and transmuting them to short-lived or stable nuclides has been in progress for 3 years under the direction of Oak Ridge National Laboratory (ORNL). This report constitutes the final assessment of transmutation in support of this program. Included are (1) a summary of recent transmutation literature, (2) a generic evaluation of actinide transmutation in thermal, fast, and other transmutation devices, (3) a preliminary evaluation of 99 Tc and 129 I transmutation, and (4) a characterization of a pressurized-water-reactor fuel cycle with and without provisions for actinide recovery and transmutation for use in other parts of the ORNL program. The principal conclusion of the report is that actinide transmutation is feasible in both thermal and fast reactors, subject to demonstrating satisfactory fuel performance, with relatively little impact on the reactor. It would also appear that additional transmutation studies are unwarranted until a firm decision to proceed with actinide transmutation has been made by the responsible authorities

Sensitivity to Nuclear Data and Neutron Source Type in Calculations of Transmutation Capabilities of the Energy Amplifier Demonstration Facility

International Nuclear Information System (INIS)

Dahlfors, Marcus

2003-05-01

This text is a summary of two studies the author has performed within the field of 3-D Monte Carlo calculations of Accelerator Driven Systems (ADS) for transmutation of nuclear waste. The simulations were carried out with the state-of-the-art computer code package EA-MC, developed by C. Rubbia and his group at CERN. The concept studied is ANSALDOs 80 MWth Energy Amplifier Demonstration Facility based on classical MOX-fuel technology and on molten Lead-Bismuth Eutectic cooling. A review of neutron cross section sensitivity in numerical calculations of an ADS and a comparative assessment relevant to the transmutation efficiency of plutonium and minor actinides in fusion/fission hybrids and ADS are presented

Sensitivity to Nuclear Data and Neutron Source Type in Calculations of Transmutation Capabilities of the Energy Amplifier Demonstration Facility

Energy Technology Data Exchange (ETDEWEB)

Dahlfors, Marcus

2003-05-01

This text is a summary of two studies the author has performed within the field of 3-D Monte Carlo calculations of Accelerator Driven Systems (ADS) for transmutation of nuclear waste. The simulations were carried out with the state-of-the-art computer code package EA-MC, developed by C. Rubbia and his group at CERN. The concept studied is ANSALDOs 80 MWth Energy Amplifier Demonstration Facility based on classical MOX-fuel technology and on molten Lead-Bismuth Eutectic cooling. A review of neutron cross section sensitivity in numerical calculations of an ADS and a comparative assessment relevant to the transmutation efficiency of plutonium and minor actinides in fusion/fission hybrids and ADS are presented.

Nuclear transmutations

International Nuclear Information System (INIS)

Mikulaj, V.

1992-01-01

Two types of nuclear transmutations are outlined, namely the radioactive transmutations and nuclear reactions. The basic characteristics are given of radioactive transmutations (gamma transmutations and isomeric transitions, beta, alpha transmutations, spontaneous fission and spontaneous emission of nucleons), their kinetics and the influence of the physical and chemical state of the radionuclide on the transmutation rate. The basic characteristics are described of nuclear reactions (reactions of neutrons including fission, reactions induced by charged particles and photons), their kinetics, effective cross sections and their mechanism. Chemical reactions caused by nuclear transmutations are discussed (recoil energy, properties of hot atoms, Szilard-Chalmers effect). A brief information is given on the behavior of radionuclides in trace concentrations. (Z.S.) 2 tabs., 19 figs., 12 refs

Accelerator driven nuclear energy and transmutation systems

International Nuclear Information System (INIS)

Boldeman, J.W.

1999-01-01

Nuclear power generation has been a mature industry for many years. However, despite the overall safety record and the great attractions of nuclear power, especially in times of concern about green house gases emissions, there continues to be some lack of public acceptance of this technology. This sensitivity to nuclear power has several elements in addition to the concern of a potential nuclear accident. These include the possible diversion of plutonium into nuclear weapon production and the concern about the long term storage of plutonium and other transuranic elements. A concept which seeks to allay these fears but still takes advantage of the nuclear fuel cycle and utilises decades of research and development in this technology, is the idea of using modern accelerators to transmute the long lived radio nuclides and simultaneously generate power. A review of the novel concepts for energy production and transmutation of isotopes will be presented. Of the various proposals, the most developed is the Energy Amplifier Concept promoted by Rubbia. The possibility of using high-energy, high-current accelerators to produce large fluxes of neutrons has been known since the earliest days of accelerator technology. E.O. Lawrence, for example, promoted the concept of producing nuclear material with such an accelerator. The Canadians in the early 50s considered using accelerators to produce fuel for their heavy water reactors and there were well advanced designs for a device called the Intense Neutron Generator. The speculative idea of using accelerator produced neutrons for the transmutation of transuranic elements (i.e. elements such as neptunium plutonium and other elements with higher Z atomic number) has also been studied extensively, notably at a number of laboratories in the US, Europe and Japan. However at this time, all facilities that have actually been constructed have been designed primarily for condensed matter studies i.e. studies of the structural properties

Specific contributions of the Dutch progamme ''RAS'' towards accelerator-based transmutation

International Nuclear Information System (INIS)

Abrahams, K.; Franken, W.M.P.; Bultman, J.H.; Heil, J.A.; Koning, A.J.

1994-09-01

Accelerator-based transmutation is being studied by ECN within its general nuclear waste transmutation programme RAS. In this paper the following contributions are presented: (1) Evaluation of cross sections at intermediate energies, within an international frame given by NEA, (2) Cell calculations on the equilibration of transuranium actinides in thermal molten-salt transmuters, (3) Irradiation facilities at the European research reactor HFR in Petten, which have been constructed with the purpose to demonstrate and investigate the transmutation of waste in a high neutron flux, (4) Studies of accelerator-based neutron generating systems to transmute neptunium and technetium, (5) Comparison of several systems on the basis of criteria for successful nuclear waste-management. (orig.)

Proton-beam window design for a transmutation facility operating with a liquid lead target

Energy Technology Data Exchange (ETDEWEB)

Jansen, C.; Lypsch, F.; Lizana, P. [Institute for Safety Research and Reactor Technology, Juelich (Germany)] [and others

1995-10-01

The proton beam target of an accelerator-driven transmutation facility can be designed as a vertical liquid lead column. To prevent lead vapor from entering the accelerator vacuum, a proton-beam window has to separate the area above the lead surface from the accelerator tube. Two radiation-cooled design alternatives have been investigated which should withstand a proton beam of 1.6 GeV and 25 mA. Temperature calculations based on energy deposition calculations with the Monte Carlo code HETC, stability analysis and spallation-induced damage calculations have been performed showing the applicability of both designs.

Transmutation Capability of a Once-Through Molten-Salt and Other Transmuting Reactors

International Nuclear Information System (INIS)

Greenspan, E.; Lowenthal, M.; Barnes, D.; Kawasaki, D.; Kimball, D.; Matsumoto, H.; Sagara, H.; Vietez, E.R.

2002-01-01

A preliminary assessment is done of the transmutation characteristics of three reactor technologies: a multi-batch liquid metal (LM) cooled transmuter, a once-through molten-salt (MS) transmuter and a pebble bed (PB) transmuter. It was found that for the same fractional transmutation and same k eff drop with burnup (Δk effBU ), lead-bismuth offers smaller peak-to-average core power density, and it requires a smaller pumping power but a larger and heavier core than a sodium cooled transmuter. 99 Tc cannot effectively serve as a burnable absorber to reduce Δk effBU of LM transmuters. However, addition of thorium can greatly flatten k eff and almost double the fractional transmutation of the LWR spent fuel from ∼20% to ∼40%. If the 'once-through' MS transmuter is operated with continuous complete removal of fission products, it can achieve ∼85% fractional transmutation provided that the equilibrium concentration of actinides in the MS can reach 4 mole %. If the fission products are not actively removed, the fractional transmutation is reduced to ∼75%. The fractional transmutation of a PB transmuter can exceed 40%. More thorough analysis is required to better quantify the transmutation capability of the different transmuter technologies. (authors)

Transmutation detectors

Energy Technology Data Exchange (ETDEWEB)

Viererbl, L., E-mail: vie@ujv.c [Research Centre Rez Ltd. (Czech Republic); Nuclear Research Institute Rez plc (Czech Republic); Lahodova, Z. [Research Centre Rez Ltd. (Czech Republic); Nuclear Research Institute Rez plc (Czech Republic); Klupak, V. [Nuclear Research Institute Rez plc (Czech Republic); Sus, F. [Research Centre Rez Ltd. (Czech Republic); Nuclear Research Institute Rez plc (Czech Republic); Kucera, J. [Research Centre Rez Ltd. (Czech Republic); Nuclear Physics Institute, Academy of Sciences of the Czech Republic (Czech Republic); Kus, P.; Marek, M. [Research Centre Rez Ltd. (Czech Republic); Nuclear Research Institute Rez plc (Czech Republic)

2011-03-11

We have designed a new type of detectors, called transmutation detectors, which can be used primarily for neutron fluence measurement. The transmutation detector method differs from the commonly used activation detector method in evaluation of detector response after irradiation. Instead of radionuclide activity measurement using radiometric methods, the concentration of stable non-gaseous nuclides generated by transmutation in the detector is measured using analytical methods like mass spectrometry. Prospective elements and nuclear reactions for transmutation detectors are listed and initial experimental results are given. The transmutation detector method could be used primarily for long-term measurement of neutron fluence in fission nuclear reactors, but in principle it could be used for any type of radiation that can cause transmutation of nuclides in detectors. This method could also be used for measurement in accelerators or fusion reactors.

Transmutation detectors

International Nuclear Information System (INIS)

Viererbl, L.; Lahodova, Z.; Klupak, V.; Sus, F.; Kucera, J.; Kus, P.; Marek, M.

2011-01-01

We have designed a new type of detectors, called transmutation detectors, which can be used primarily for neutron fluence measurement. The transmutation detector method differs from the commonly used activation detector method in evaluation of detector response after irradiation. Instead of radionuclide activity measurement using radiometric methods, the concentration of stable non-gaseous nuclides generated by transmutation in the detector is measured using analytical methods like mass spectrometry. Prospective elements and nuclear reactions for transmutation detectors are listed and initial experimental results are given. The transmutation detector method could be used primarily for long-term measurement of neutron fluence in fission nuclear reactors, but in principle it could be used for any type of radiation that can cause transmutation of nuclides in detectors. This method could also be used for measurement in accelerators or fusion reactors.

Transmutation of Americium in Fast Neutron Facilities

OpenAIRE

Zhang, Youpeng

2011-01-01

In this thesis, the feasibility to use a medium sized sodium cooled fast reactor fully loaded with MOX fuel for efficient transmutation of americium is investigated by simulating the safety performance of a BN600-type fast reactor loaded with different fractions of americium in the fuel, using the safety parameters obtained with the SERPENT Monte Carlo code. The focus is on americium mainly due to its long-term contribution to the radiotoxicity of spent nuclear fuel and its deterioration on c...

Transmutation of high-level radioactive waste - Perspectives

CERN Document Server

Junghans, Arnd; Grosse, Eckart; Hannaske, Roland; Kögler, Toni; Massarczyk, Ralf; Schwengner, Ronald; Wagner, Andreas

2014-01-01

In a fast neutron spectrum essentially all long-lived actinides (e.g. Plutonium) undergo fission and thus can be transmuted into generally short lived fission products. Innovative nuclear reactor concepts e.g. accelerator driven systems (ADS) are currently in development that foresee a closed fuel cycle. The majority of the fissile nuclides (uranium, plutonium) shall be used for power generation and only fission products will be put into final disposal that needs to last for a historical time scale of only 1000 years. For the transmutation of high-level radioactive waste a lot of research and development is still required. One aspect is the precise knowledge of nuclear data for reactions with fast neutrons. Nuclear reactions relevant for transmutation are being investigated in the framework of the european project ERINDA. First results from the new neutron time-of-flight facility nELBE at Helmholtz-Zentrum Dresden-Rossendorf will be presented.

Specific contributions of the Dutch programme {open_quotes}RAS{close_quotes} towards accelerator-based transmutation

Energy Technology Data Exchange (ETDEWEB)

Abrahams, K.; Franken, W.M.P.; Bultman, J.H. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands)] [and others

1995-10-01

Accelerator-based transmutation is being studied by ECN within its general nuclear waste transmutation programme RAS. In this paper the following contributions are presented: (1) Evaluation of cross sections at intermediate energies, within an international frame given by NEA, (2) Cell calculations on the equilibration of transuranium actinides in thermal molten-salt transmuters, (3) Irradiation facilities at the European research reactor HFR in Petten, which have been constructed with the purpose to demonstrate and investigate the transmutation of waste in a high neutron flux, (4) Studies of accelerator-based neutron generating systems to transmute neptunium and technetium, (5) Comparison of several systems on the basis of criteria for successful nuclear waste-management.

U.S. advanced accelerator applications program: plans to develop and test waste transmutation technologies

International Nuclear Information System (INIS)

Van Tuyle, G.; Bennett, D.; Arthur, E.; Cappiello, M.; Finck, P.; Hill, D.; Herczeg, J.; Goldner, F.

2001-01-01

The primary mission of the U.S. Advanced Accelerator Applications (AAA) Program is to establish a national nuclear technology research capability that can demonstrate accelerator-based transmutation of waste and conduct transmutation research while at the same time providing a capability for the production of tritium if required. The AAA Program was created during fiscal year 2001 from the Accelerator Transmutation of Waste (ATW) Program and the Accelerator Production of Tritium (APT) Project. This paper describes the new AAA Program, as well as its two major components: development and testing of waste transmutation technologies and construction of an integrated accelerator-driven test facility (ADTF). (author)

R and D activities for partitioning and transmutation in Korea

International Nuclear Information System (INIS)

Jae-Hyung, Yoo; Won-Seok, Park

2003-01-01

According to the long-term plan of nuclear technology development, KAERI is conducting a research and development project of transmutation with the objective of key technology development in the areas of partitioning and transmutation system. The research and development activities for partitioning and transmutation of long-lived radionuclides are introduced in this work. The studies of partitioning are focused on the electrorefining and electrowinning, which are aimed at investigating the thermodynamic properties of electrodeposition behaviours as well as the separation efficiency. As for the transmutation system, the HYPER (HYbrid Power Extraction Reactor) combined by a proton accelerator and a sub-critical reactor is being studied in KAERI as a prominent candidate facility in the future. Some conceptual studies are being conducted to develop key elemental systems of the sub-critical reactor such as the core, TRU fuel, proton target, and the cooling system. The conceptual design of the HYPER system will be completed by 2006. (author)

Design and safety studies on the European Facility for Industrial Transmutation (EFIT) with CERMET fuel

International Nuclear Information System (INIS)

Chen, X.N.; Rineiski, A.; Liu, P.; Matzerath Boccaccini, C.; Flad, M.; Gabrielli, F.; Maschek, W.; Morita, K.

2008-01-01

European R and D for ADS design and fuel development is driven in the 6 th FP of the EU by the EUROTRANS Programme [1]. In EUROTRANS two ADS design routes are followed, the XT-ADS and the EFIT. The XT-ADS is designed to provide the experimental demonstration of transmutation in an Accelerator Driven System. The EFIT development, the European Facility for Industrial Transmutation, aims at a generic conceptual design of a full transmuter. A key issue of the R and D work is the choice of an adequate fuel to be used in an Accelerator Driven Transmuter (ADT) like EFIT. Various fuel forms have been assessed. CERCER and CERMET fuels, specifically with the matrices MgO and Mo, have finally been selected and are now under closer investigation. Within EUROTRANS, a special domain named 'AFTRA', is responsible to more deeply assess the behavior of these dedicated fuels and to provide the fuel data base for the core design of the EFIT. The EFIT concept has to be optimized towards: a good transmutation efficiency, high burnup, low reactivity swing, low power peaking, adequate subcriticality, reasonable beam requirements and a high safety level. The final recommendation on fuels by AFTRA gave a ranking of these fuels based on the mentioned criteria. The composite CERMET fuel (Pu 0.5 ,Am 0.5 )O 2-x - Mo (with the isotope 92 Mo comprising 93% of the molybdenum) has been recommended as the primary candidate for the EFIT. This CERMET fuel fulfils adopted criteria for fabrication and reprocessing, and provides excellent safety margins. Disadvantages include the cost for enrichment of 92 Mo and a lower specific transmutation rate of minor actinides, because of the higher neutron absorption cross-section of the matrix. The composite CERCER fuel (Pu 0.4 ,Am 0.6 )O 2-x - MgO has therefore been recommended as a backup solution as it might offer a higher consumption rate of minor actinides, and can be manufactured for a lower unit cost. This paper is in fact a sequel to our last paper [2

Nuclear Waste Separation and Transmutation Research with Special Focus on Russian Transmutation Projects Sponsored by ISTC

International Nuclear Information System (INIS)

Conde, Henri; Blomgren, Jan; Olsson, Nils

2003-03-01

High-level nuclear reactor waste is made up of relatively few long-lived radioactive species, among them plutonium, that contribute to difficulties with its storage and disposal. Separation of these species from larger waste volumes mainly constituting of uranium (about 95 %) coupled with nuclear incineration to fission products of plutonium and the so called minor actinides (Neptunium, Americium, and Curium) and transmutation of some of the long lived fission products to short lived or stable isotopes represents a viable nuclear waste management strategy to drastically reduce the time and space requirements for a bed-rock repository of the remaining waste. A remarkable increase in the international research and development on partitioning and transmutation has occurred during the recent years. The road-map report published in April 2001 by The European Technical Working Group on ADS for the development of a European demonstration facility for nuclear waste transmutation has high-lighted the ongoing European research and pointed out the need for further research. The road-map has given the different research activities a position in the ultimate goal of producing an ADS demonstrator and is guiding research planning on the national as well as on the EU level. The Advanced Accelerator Application (3A) program in the US, with the long term goals to enhance long term public safety, provide benefits for the repository, reduce proliferation risks and improve prospects for nuclear power has focused the research on nuclear waste transmutation. The reports on the 3A program indicates a change of the US former abandonment position towards reprocessing and fast reactors due to a strong incentive to eliminate the reactor plutonium and to lower the amount of high level reactor waste for the Yucca Mountain repository. The SKB's proposed research and development program for the next 3 years (FUD01) was presented by SKB in September 2001. It is proposed that the research program

Special scientific programme on use of high energy accelerators for transmutation of actinides and power production

International Nuclear Information System (INIS)

1994-09-01

Various techniques for the transmutation of radioactive waste through the use of high energy accelerators are reviewed and discussed. In particular, the present publication contains presentations on (i) requirements and the technical possibilities for the transmutation of long-lived radionuclides (background paper); (ii) high energy particle accelerators for bulk transformation of elements and energy generation; (iii) the resolution of nuclear energy issues using accelerator-driven technology; (iv) the use of proton accelerators for the transmutation of actinides and power production; (v) the coupling of an accelerator to a subcritical fission reactor (with a view on its potential impact on waste transmutation); (vi) research and development of accelerator-based transmutation technology at JAERI (Japan); and (vii) questions and problems with regard to accelerator-driven nuclear power and transmutation facilities. Refs, figs and tabs

Minor actinide transmutation using minor actinide burner reactors

International Nuclear Information System (INIS)

Mukaiyama, T.; Yoshida, H.; Gunji, Y.

1991-01-01

The concept of minor actinide burner reactor is proposed as an efficient way to transmute long-lived minor actinides in order to ease the burden of high-level radioactive waste disposal problem. Conceptual design study of minor actinide burner reactors was performed to obtain a reactor model with very hard neutron spectrum and very high neutron flux in which minor actinides can be fissioned efficiently. Two models of burner reactors were obtained, one with metal fuel core and the other with particle fuel core. Minor actinide transmutation by the actinide burner reactors is compared with that by power reactors from both the reactor physics and fuel cycle facilities view point. (author)

Partitioning and transmutation (P and T) 1997. Status report

International Nuclear Information System (INIS)

Enarsson, Aasa; Landgren, A.; Liljenzin, J.O.; Skaalberg, M.; Spjuth, L.; Gudowski, W.; Wallenius, J.

1998-05-01

Research on and the evaluation of partitioning and transmutation are currently in progress in many industrial countries due to its potential as a long-term, sustainable energy source with low environmental impact and due to its ability to destroy many long-lived nuclides. The cost of the research and development work on partitioning and transmutation is considered to be so great that international co-operation is required. With respect to Sweden, we recommend a balanced research work on both partitioning and transmutation technology. Within the area of partitioning, it is above all a question of locating new reagents which can be used to simplify the necessary partitioning processes and minimize the losses. The requirements with respect to high selectivity and minor losses will be significantly higher in a recirculating system based on transmutation than in the reprocessing facilities of today where only uranium and plutonium are recovered. If the utilized reagents can be easily destroyed, by dry or wet incineration and conversion into non-complex gaseous chemical compounds, this will open up good opportunities for the recovery of the radionuclides. From a purely technical standpoint, it would seem that a combination of different types of reactor systems would give the best possible transmutation efficiency. While existing light water reactors can be utilized for increased plutonium incineration, there is currently consensus about the view that reactors with high-energy neutrons are necessary to achieve a sufficiently high transmutation efficiency for neptunium, americium, curium and certain fission products. By allowing an accelerator-based neutron source to drive a subcritical heavy metal-cooled reactor, the potential for transmutation of fission products is increased, at the same time that satisfactory safety margins are achieved for certain fuel types with a low share of delayed neutrons and a high heat conductivity. Regardless of what types of systems are

Partitioning and transmutation (P and T) 1997. Status report

Energy Technology Data Exchange (ETDEWEB)

Enarsson, Aasa; Landgren, A.; Liljenzin, J.O.; Skaalberg, M.; Spjuth, L. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Chemistry; Gudowski, W.; Wallenius, J. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

1998-05-01

Research on and the evaluation of partitioning and transmutation are currently in progress in many industrial countries due to its potential as a long-term, sustainable energy source with low environmental impact and due to its ability to destroy many long-lived nuclides. The cost of the research and development work on partitioning and transmutation is considered to be so great that international co-operation is required. With respect to Sweden, we recommend a balanced research work on both partitioning and transmutation technology. Within the area of partitioning, it is above all a question of locating new reagents which can be used to simplify the necessary partitioning processes and minimize the losses. The requirements with respect to high selectivity and minor losses will be significantly higher in a recirculating system based on transmutation than in the reprocessing facilities of today where only uranium and plutonium are recovered. If the utilized reagents can be easily destroyed, by dry or wet incineration and conversion into non-complex gaseous chemical compounds, this will open up good opportunities for the recovery of the radionuclides. From a purely technical standpoint, it would seem that a combination of different types of reactor systems would give the best possible transmutation efficiency. While existing light water reactors can be utilized for increased plutonium incineration, there is currently consensus about the view that reactors with high-energy neutrons are necessary to achieve a sufficiently high transmutation efficiency for neptunium, americium, curium and certain fission products. By allowing an accelerator-based neutron source to drive a subcritical heavy metal-cooled reactor, the potential for transmutation of fission products is increased, at the same time that satisfactory safety margins are achieved for certain fuel types with a low share of delayed neutrons and a high heat conductivity. Regardless of what types of systems are

Transmutation Technology Development

Energy Technology Data Exchange (ETDEWEB)

Song, T. Y.; Park, W. S.; Kim, Y. H. (and others)

2007-06-15

The spent fuel coming from the PWR is one of the most difficult problems to be solved for the continuous use of nuclear power. It takes a few million years to be safe under the ground. Therefore, it is not easy to take care of the spent fuel for such a long time. Transmutation technology is the key technology which can solve the spent fuel problem basically. Transmutation is to transmute long-lived radioactive nuclides in the spent fuel into short-lived or stable nuclide through nuclear reactions. The long-lived radioactive nuclides can be TRU and fission products such as Tc-99 and I-129. Although the transmutation technology does not make the underground disposal totally unnecessary, the period to take care of the spent fuel can be reduced to the order of a few hundred years. In addition to the environmental benefit, transmutation can be considered to recycle the energy in the spent fuel since the transmutation is performed through nuclear fission reaction of the TRU in the spent fuel. Therefore, transmutation technology is worth being developed in economical aspect. The results of this work can be a basis for the next stage research. The objective of the third stage research was to complete the core conceptual design and verification of the key technologies. The final results will contribute to the establishment of Korean back end fuel cycle policy by providing technical guidelines.

Proceedings of the specialists' meeting on accelerator-based transmutation

International Nuclear Information System (INIS)

Wenger, H.U.

1992-09-01

The meeting was organised under the auspices of OECD Nuclear Agency's International Information Exchange Programme on Actinide and Fission Product Partitioning and Transmutation. In the original announcement for the meeting the following sessions were proposed: 1) Concepts of accelerator-based transmutation systems, 2) Nuclear design problems of accelerator-based transmutation systems with emphasis on target facilities and their interfaces with accelerators, 3) Data and methods for nuclear design of accelerator-based transmutation systems, 4) Related cross-section measurements and integral experiments, 5) Identification of discrepancies and gaps and discussion of desirable R+D and benchmark activities. Due to the large number of papers submitted it was necessary to split session 2 into two parts and to reassign some papers in order to balance the sessions more evenly. No papers were submitted for session 5 and this was replaced by a summary and general discussion session. These proceedings contain all 30 papers in the order they were presented at the meeting. They are copies of the duplication-ready versions given to us during or shortly after the meeting. In the Table of Contents, the papers are listed together with the name of the presenter. (author) figs., tabs., refs

Gamma ray beam transmutation

International Nuclear Information System (INIS)

Imasaki, K.; Li, D.; Miyamoto, S.; Amano, S.; Motizuki, T.

2007-01-01

We have proposed a new approach to nuclear transmutation by a gamma ray beam of Compton scattered laser photon. We obtained 20 MeV gamma ray in this way to obtain transmutation rates with the giant resonance of 1 97Au and 1 29Iodine. The rate of the transmutation agreed with the theoretical calculation. Experiments on energy spectrum of positron, electron and neutron from targets were performed for the energy balance and design of the system scheme. The reaction rate was about 1.5∼4% for appropriate photon energies and neutron production rate was up to 4% in the measurements. We had stored laser photon more than 5000 times in a small cavity which implied for a significant improvement of system efficiency. Using these technologies, we have designed an actual transmutation system for 1 29Iodine which has a 16 million year's activity. In my presentation, I will address the properties of this scheme, experiments results and transmutation system for iodine transmutation

Transmutation of long-lived nuclides in the fuel cycle of Brest-type reactors

International Nuclear Information System (INIS)

Lopatkin, A.V.; Orlov, V.V.; Filin, A.I.

2001-01-01

Transmutation of long-lived nuclides produced as a result of nuclear generation, should be set up proceeding from the principle of reasonable sufficiency, expressed as radiation equivalence between the radwaste sent to disposal and source natural uranium. In this case, introduction of fast reactors of new generation (such as BREST or other reactors based on similar philosophy) will resolve transmutation problems even with the thermal-to-fast reactor capacity ratio of 2:1. The authors of the 'Strategy of nuclear power development in Russia' foresee, and substantiate their prediction, that fast reactors of the new generation will account for no less than 2/3 of nuclear capacity in future large-scale nuclear power sector. Fast reactors will be the basis of a transmutation fuel cycle, which will remove the need of creating additional transmutation facilities. (author)

Transmutation potential of reactor WWER-440

International Nuclear Information System (INIS)

Darilek, P.; Sebian, V.; Necas, V.

2001-01-01

Theoretical evaluation of WWER-440 transmutation potential by HELIOS - code is presented. Transmutation method proposal comprising special transmutation pins, combined FA and simple reprocessing is described. Transmutation efficiency of the method is characterized (Authors)

Waste transmutation and public acceptance

International Nuclear Information System (INIS)

Pigford, T.H.

1991-01-01

The concept of transmuting radioactive wastes with reactors or accelerators is appealing. It has the potential of simplifying or eliminating problems of disposing of nuclear waste. The transmutation concept has been renewed vigorously at a time when national projects to dispose of high-level and transuranic waste are seriously delayed. In this period of tightening federal funds and program curtailments, skilled technical staffs are available at US Department of Energy (DOE) national laboratories and contractors to work on waste transmutation. If the claims of transmutation can be shown to be realistic, economically feasible, and capable of being implemented within the US institutional infrastructure, public acceptance of nuclear waste disposal may be enhanced. If the claims for transmutation are not substantiated, however, there will result a serious loss of credibility and an unjust exacerbation of public concerns about nuclear waste. The paper discusses the following topics: how public acceptance is achieved; the technical community and waste disposal; transmutation and technical communication; transmutation issues; technical fixes and public perception

Separation and transmutation. A picture of the applications in Sweden; Separation och transmutation. Belysning av tillaempning i Sverige

Energy Technology Data Exchange (ETDEWEB)

Grundfelt, Bertil; Lindgren, Maria [Kemakta Konsult AB, Stockholm (Sweden)

2006-11-15

This report contains a review of the transmutation technology and an elucidation of the consequences of the use of transmutation in Sweden. Transmutation has often been mentioned in the public debate as a way of rendering harmless the high-level waste from nuclear power such that the final disposal of the waste can be substantially simplified or even completely avoided. However, it can be noted that even with an exploitation of transmutation, significant amounts of radioactive waste requiring qualified final disposal will be generated. The transmutation technology will make it possible to reduce the longevity of the high-level waste by converting primarily the transuranic elements to fission products with shorter half lives. The long-term radiotoxicity of the spent nuclear fuel is dominated by the transuranics. Hence, transmutation will lead to a substantial decrease of the long-term radiotoxicity of the spent fuel. The research on transmutation has been focussed on sub-critical so called ADS-reactors (Accelerator Driven System). In such a system protons are accelerated to very high energy levels (in the order of GeV) in an electromagnetic field. The accelerated protons are impacted on a spallation source consisting of heavy atoms, e.g. lead or a mixture of lead and bismuth. At the impact the heavy nuclei are spalled releasing a number of neutrons that can be used for fissioning the nuclei of the substances to be transmuted, primarily the transuranics. ADS-reactors are still at the research stage. It is a common view that it will take several decades before the technology has reached a maturity that allows the construction of a demonstration facility. Calculations performed at Royal Institute of Technology in Stockholm show that using the ADS-technology would allow a reduction of the inventory of transuranics in the spent fuel from Swedish reactors by 50-85% within a 50-100 years period. The goal to transmute 99% of the transuranics inventory has been achieved in

Efficiency Of Transuranium Nuclides Transmutation

International Nuclear Information System (INIS)

Kazansky, Yu.A.; Klinov, D.A.; Semenov, E.V.

2002-01-01

One of the ways to create a wasteless nuclear power is based on transmutation of spent fuel nuclides. In particular, it is considered that the radioactivity of the nuclear power wastes should be the same (or smaller), than radioactivity of the uranium and the thorium extracted from entrails of the Earth. The problem of fission fragments transmutation efficiency was considered in article, where, in particular, the concepts of transmutation factor and the ''generalised'' index of biological hazard of the radioactive nuclides were entered. The transmutation efficiency has appeared to be a function of time and, naturally, dependent on nuclear power activity scenario, from neutron flux, absorption cross-sections of the nuclides under transmutation and on the rate of their formation in reactors. In the present paper the efficiency of the transmutation of transuranium nuclides is considered

A study for optimal transmutation system

International Nuclear Information System (INIS)

Park, W.S.; Song, T.Y.; Shin, H.S.; Park, C.K.

1996-01-01

Couple of transmutation systems are being under investigation to design the optimal transmutation device. Several basic studies were performed for that objectives: (1) select the radioactive nuclides to be transmuted: (2) investigate the physical characteristics of each nuclide; (3) study the most favorable neutron energy environment for the transmutation. The existing LWR and LMFBR cores were found to be not a satisfiable ones in terms of transmutation rate itself. (author). 5 refs, 2 figs, 3 tabs

Development of long-lived radionuclide transmutation technology -Development of nuclear transmutation technology-

Energy Technology Data Exchange (ETDEWEB)

Lee, Myung Chan; Jung, Woo Tae; Koh, Duk Joon; Kim, Jung Doh; Kil, Choong Sub [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-07-01

Based on the performance assessment of current reactor nuclear design codes, CASMO-3, LEOPARD, CITATION could be used for the simulation of transmutation, but further improvements are required on the reliability of cross sections of MA or FP and the accuracy of burnup model. Our simulation results based on the calculation by using CASMO-3 and NEM-3D (developed at Seoul National University) showed that transmutation efficiency for Am was high but Np and Cm elements were found to be hard to transmute. In our calculation, micro depletion calculations with burnup variation were done separately. Possibility of MA and FP transmutation with hard and fast neutrons was reported to be greater but detail calculation will be done in next year. 44 figs, 31 tabs, 17 refs. (Author).

Nuclear waste transmutation

International Nuclear Information System (INIS)

Salvatores, M.; Girard, C.; Delpech, M.; Slessarev, I.; Tommasi, J.

1994-01-01

Waste management strategies foresee the use of a deep geological repository either for final disposal of irradiated fuel or, after reprocessing and reuse of U and Pu for final disposal of long-lived radio-active materials. In the second case, partitioning and transmutation of these materials can be considered to reduce the impact of radiation on man due to the storage. On the basis of the SPIN programme developed by CEA in this field, the main features of transmutation is presented. The goal to achieve and the criteria to use are quite difficult to establish. The rights para-meters to characterize the risk are the potential radiotoxicity in the the repository and the residual radiotoxicity at the outlet. Transmutation studies in CEA used the potential radiotoxicity which is based on well-known parameters and less precise hazardous factors. The second point to appreciate the trans- mutation interest is to dispose of a criteria for the radio-radiotoxicity reduction. As there is no general agreement, we try to have a toxicity as low as possible within reasonable technical limits. To reduce the long term radio- toxicity, Pu, minor actinides and some long-lived fission products have to be transmuted. To assess the feasibility of such trans-mutation in reactors or advanced systems, one has to consider constraints on neutronic balance, safety, fuel cycle, technology , economy. Taking in account the main conclusions of this analysis, parametric studies of homogeneous and heterogenous transmutation permit a choice of promising solutions. Goals are to use every long-lived element with a minimized production of other long- lived elements in order to obtain an appreciable radiotoxicity reduction. It implies multi recycling of Pu which favours fast neutron reactors and different strategies of multi recycling for Np, Am, Cm. Multi recycling makes the results strongly dependant of losses. Researches to obtain the high partitioning efficiency needed are in progress. Calculations

Neutron transmutation doping of silicon

International Nuclear Information System (INIS)

Mireshghi, A.

1989-01-01

After a brief review of the theoretical bases for Neutron Transmutation Doping (NTD) process, the equations necessary for calculation of doped crystal resistivity (p) in terms of parameters of irradiation, such as time and neutron flux, are derived. The procedure for production of NTD-Si is described, important considerations are outlined and the advantages and applications are introduced. Also, an assessment is made of the practicality of using AEOI Research Reactor thermal neutron irradiation facilities for production of NTD-Si, which is concluded to be possible at reactor nominal operation conditions

Scenarios for minor actinides transmutation in the framework of the French Act on Waste Management

International Nuclear Information System (INIS)

Coquelet-Pascal, C.; Meyer, M.; Tiphine, M.; Girieud, R.; Eschbach, R.; Chabert, C.; Garzenne, C.; Barbrault, P.; Van Den Durpel, L.; Caron-Charles, M.; Favet, D.; Arslan, M.; Caron-Charles, M.; Carlier, B.; Lefevre, J.C.

2013-01-01

In the framework of the French Act on Waste Management, options of minor actinides (MA) transmutation are studied, based on several scenarios of sodium fast reactor deployment. Basically, one of these scenarios considers the deployment of a 60 GWe SFR fleet in two steps (20 GWe from 2040 to 2050 and 40 GWe, as well as, from 2080 to 2100). For this scenario, the advantages and drawbacks of different transmutation options are evaluated: - transmutation of all minor actinides or only of americium; - transmutation in homogeneous mode (MA bearing fuel in all the core or just in the outer core) or in heterogeneous mode (MA bearing radial blankets). Scenarios have been optimised to limit the impacts of MA transmutation on the cycle: - reduction of the initial MA content in the core in the case of transmutation in homogeneous mode to reduce the impact on reactivity coefficients; - reduction of the number of rows of blankets and fuel decay heat in the case of transmutation in heterogeneous mode. The sensitivity of transmutation options to cycle parameters such as the fuel cooling time before transportation is also assessed. Thus, the transmutation of only americium in one row of radial blankets containing initially 10 pc % Am and irradiated during the same duration as the standard fuel assemblies appears to be a suitable solution to limit the transmutation impacts on fuel cycle and facilities. A comparison of results obtained with MA transmutation in dedicated systems is also presented with a symbiotic scenario considering ADS (accelerator-driven system) deployment to transmute MA together with a SFR fleet to produce energy. The MA inventory within the cycle is higher in the case of transmutation in ADS than in the case of transmutation in SFR. Considering the industrial feasibility of MA transmutation, it appears important to study 'independently' SFR deployment and MA transmutation. Consequently, scenarios of progressive introduction of MA options are assessed

Technical meeting on 'Review of solid and mobile fuels for partitioning and transmutation systems'. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-07-01

The topics covered during the Meeting were divided into two Sessions. Session 1 - Qualification of Solid and Mobile Fuels delt with: Neutronic, fuel and material properties of a molten salt transmuter; and Preliminary analysis of transmutation fuels for KALIMER. Session 2 - Reactor Physics and Safety Characteristics of Transmutation Systems based on Solid and Mobile Fuel Types included the following: Activity in NEA for P and T area; IAEA activities in the area of partitioning and transmutation; The R and D activity in Brazil: A conceptual fast energy amplifier ADS cooled by helium double stata Th/U fuel cycle; Closed fuel cycle and contemporary tendencies of the nuclear facilities development; Current Russian activities in P and T area; Pyrochemical reprocessing and nuclear spent fuel disposal project; Fuel selection criteria specific for double stratum minor actinide burners.

Transmutation of transuranium elements in a gas-cooled accelerator-driven system

International Nuclear Information System (INIS)

Biss, Klaus Hendrik

2014-01-01

The peaceful usage of nuclear energy by light and boiling water reactors is connected with a buildup of long-lived high-level radioactive waste. Compared to the direct disposal, partitioning and transmutation (P and T) is considered as an effective way to reduce this waste in its quantity by converting it into short-lived radio nuclides. By that the long term radiotoxicity is reduced compared to direct disposal. Subcritical systems, which are powered by spallation processes for free neutron production to maintain the nuclear chain reaction, allow a target-oriented transmutation. As a subcritical system a gas-cooled accelerator driven system (ADS) for transmutation of transuranic elements has been modeled in this thesis to evaluate the reduction of the radio toxicity by P and T. The simulation of neutron-physical processes is based on the Monte Carlo computer program MCNPX. The development of an equilibrium core made it possible to study the transmutation and operating behavior for several fuel variations in a magnesium oxide matrix and develop a simplified burnup method. Americium as part of the fuel has a stabilizing effect on the neutron multiplication due to its conversion into plutonium during the operation. Thorium was investigated as an alternative matrix for the fuel in order to replicate the stabilizing effect of americium by the conversion of thorium in 233 U. By that a consistent operating cycle in the later P and T-process is ensured. Calculation of the nuclide composition at the end of a P and T-process leads to an expansion of the mathematical description of the mass reduction (transmutation efficiency) by the material located in the reactor. The achieved transmutation efficiency with the investigated ADS is 98.8 %. The transmutation time was examined with different operating strategies regarding the number, size and thermal power of use of transmutation facilities to determine the effort for the P and T-process depending on efficiency. It turns out

Waste partitioning and transmutation as a means towards long-term risk reduction

International Nuclear Information System (INIS)

Merz, E.R.

1993-09-01

It has been an idea for some time to reduce the long-term potential hazard of the waste by chemical removal of the actinides as well as some long-lived fission products and their subsequent transmutation in an intense neutron flux. Transmutation would thus shorten the required containment period of radioactive material in a repository. It is estimated, that development of such technology would take at least 40 years because facilities would be required to perform a clean actinide and fission product isolation and to fabricate the fuel elements that contained the separated nuclides. This latter requirements would involve a major expansion of new chemical process steps which are not available as yet. Development of new equipment to maintain occupational exposures as low as reasonably achievable and to minimize releases of radioactivity to the environment would also be necessary. Partitioning and transmutation should be introduced, if at all, as a long-term decision about new nuclear power technology as a future energy source. With regard to this, R and D work dealing with basic questions seems to be worthwhile, However, the introduction of partitioning and transmutation will not eliminate the need for radioactive waste disposal. (orig./HP) [de

Transmutation of radioactive wastes: how and why?

International Nuclear Information System (INIS)

Patarin, L.

2004-01-01

After having evoked the natural or spontaneous transmutation of natural or artificial radioactive atoms, the author describes how this transmutation is technically obtained, indicates the two main families of atoms present in a used nuclear fuel and for which transmutation is to be investigated (long-lived fission residues or products, and transuranium elements) and of which the behaviour in neutron fluxes must be explored. He discusses the industrial means required for artificial transmutation. He discusses the interest of performing such a transmutation

The Impact of Partitioning and Transmutation on the Risk Assesment of a Spent Nuclear Fuel

International Nuclear Information System (INIS)

Amrani, Naima

2006-01-01

Partitioning and transmutation of radioactive and long lived component from the highly radioactive waste stream in order to reduce or probably eliminate their radiotoxic inventory was the important option for the nuclear waste management. The principal radionuclides contribution to the long term radiotoxic inventory is mostly due to Pu, minor actinides and some long-lived fission products. The conditioning operation can present artificial barriers which are potentially capable of confining the radionuclides within their package for thousands of years. After this time nothing can be predicted. The solubility of the actinides (except Np) is generally low whereas the long lived fission product. particularly 137 Cs, 129 I and in some case 99 Tc, display high mobility In the geosphere. Conditioning of separated long-lived nuclides in appropriate matrices which could serve as irradiation matrix in a delayed transmutation option is a possible outcome for the next decades. The general strategy of introducing Partitioning and Transmutation as an additional waste management option is based on the radiological benefit which is expected from such an option. The short term impact of partitioning would be to reduce long-term radiotoxic inventory of the resulting HLW at the expense of an increase of the operational requirements for the nuclear facilities concerned. Fast neutron spectrum devices (FR or ADS facilities) are more efficient than current LWRs for recycling and transmuting long-lived radionuclides

Neutron data for accelerator-driven transmutation technologies. Annual Report 2004/2005

International Nuclear Information System (INIS)

Blomgren, J.; Nilsson, L.; Mermod, P.; Olsson, N.; Pomp, S.; Oehrn, A.; Oesterlund, M.

2005-09-01

The project NATT, Neutron data for Accelerator-driven Transmutation Technology, is performed within the nuclear reactions group of the Dept. of Neutron Research, Uppsala univ. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group has previously developed two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: An article on three-body force effects has been on the top-ten downloading list of Physics Letters B. Uppsala had the largest foreign delegation at the International Conference on Nuclear Data for Science and Technology in Santa Fe, NM, USA, and presented the largest number of papers of all experimental groups. A neutron flux monitor for the new FOI neutron beam facility has been developed, commissioned and taken into regular operation. Within the project, one licentiate exam has been awarded. The new neutron beam facility at TSL has been taken into commercial operation and is now having the largest commercial turnover of all European facilities in the field

Nuclear transmutation by flux compression

International Nuclear Information System (INIS)

Seifritz, W.

2001-01-01

A new idea for the transmutation of minor actinides, long (and even short) lived fission products is presented. It is based an the property of neutron flux compression in nuclear (fast and/or thermal) reactors possessing spatially non-stationary critical masses. An advantage factor for the burn-up fluence of the elements to be transmuted in the order of magnitude of 100 and more is obtainable compared with the classical way of transmutation. Three typical examples of such transmuters (a subcritical ringreactor with a rotating reflector, a sub-critical ring reactor with a rotating spallation source, the socalled ''pulsed energy amplifier'', and a fast burn-wave reactor) are presented and analysed with regard to this purpose. (orig.) [de

Neutron data experiments for transmutation. Annual Report 2006/2007

International Nuclear Information System (INIS)

Blomgren, J.; Andersson, P.; Bevilacqua, R.; Nilsson, L.; Pomp, S.; Simutkin, V.; Oehrn, A.; Oesterlund, M.

2007-10-01

The project NEXT, Neutron data Experiments for Transmutation, is performed within the nuclear reactions group of the Department of Neutron Research, Uppsala University. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group is operating two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: The TSL neutron beam facility and the MEDLEY detector system have been upgraded. Funding for a major upgrade of the SCANDAL facility has been approved, and practical work has been initiated. Three new PhD students have been accepted. The Uppsala group contributed twelve accepted publications at the International Conference on Nuclear Data for Science and Technology, Nice, France, April 22-27, 2007. The EU project CANDIDE (Coordination Action on Nuclear Data for Industrial Development in Europe), coordinated by Jan Blomgren, started January 1, 2007. The EU project EFNUDAT (European Facilities for Nuclear Data research), partly coordinated by Jan Blomgren, started November 1, 2006. Nuclear power education has reached all-time high at Uppsala University. A contract with KSU (Nuclear Training and Safety Centre) on financing the increased volume of teaching for industry needs has been signed

Neutron data experiments for transmutation. Annual Report 2006/2007

Energy Technology Data Exchange (ETDEWEB)

Blomgren, J.; Andersson, P.; Bevilacqua, R.; Nilsson, L.; Pomp, S.; Simutkin, V.; Oehrn, A.; Oesterlund, M. (Uppsala Univ. (SE). Dept. of Neutron Research)

2007-10-15

The project NEXT, Neutron data Experiments for Transmutation, is performed within the nuclear reactions group of the Department of Neutron Research, Uppsala University. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group is operating two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: The TSL neutron beam facility and the MEDLEY detector system have been upgraded. Funding for a major upgrade of the SCANDAL facility has been approved, and practical work has been initiated. Three new PhD students have been accepted. The Uppsala group contributed twelve accepted publications at the International Conference on Nuclear Data for Science and Technology, Nice, France, April 22-27, 2007. The EU project CANDIDE (Coordination Action on Nuclear Data for Industrial Development in Europe), coordinated by Jan Blomgren, started January 1, 2007. The EU project EFNUDAT (European Facilities for Nuclear Data research), partly coordinated by Jan Blomgren, started November 1, 2006. Nuclear power education has reached all-time high at Uppsala University. A contract with KSU (Nuclear Training and Safety Centre) on financing the increased volume of teaching for industry needs has been signed

Evaluation of alternative partitioning/transmutation scenarios using transmutation in light-water reactors (LWRs)

International Nuclear Information System (INIS)

Collins, E.D.; Renier, J.P.; Del Cul, B.; Spencer, B.

2005-01-01

Previous Advanced Fuel Cycle Initiative (AFCI) studies were made to assess the effects of the existing accumulation of LWR spent fuel in the United States on the capability to partition/transmute actinides using existing and advanced LWR. The concept of treating the oldest fuel first indicated that significant advantages could be gained in both partitioning, transmutation, and in overall cost reduction. The processing scenarios previously evaluated assumed that (1) 2000 MT/year of spent fuel, irradiated to 45 GWd/MT and decayed for 30 years is processed; (2) recovered plutonium and 90% of the neptunium are transmuted in LWR MOX fuel; and (3) minor actinides, consisting of americium, curium, and 10% of the neptunium are transmuted in burnable poison type targets. Results of the previous study showed that significant benefits could be obtained, including (1) lower costs for partitioning and transmutation and for storage of spent fuel, (2) maintenance of proliferation resistance for the fissile plutonium in spent fuels, and (3) extended lifetime for the repository. The lower costs would be achieved primarily because no capital investment for a special transmuter reactor (fast reactor, accelerator-driven system, etc.) would be required. Instead, only existing and new LWRs would be utilized. Moreover, no new storage capacity could be needed for spent fuels and irradiated targets because the number of spent fuel assemblies would remain the same after the scenario is begun. Even though the total inventory of plutonium would rise during the early cycles, ∼98% of the plutonium would be contained in stored spent fuel and would be protected by high radiation (the Spent Fuel Standard). This is because the spent fuel would be reprocessed and re-irradiated at intervals within which the fission products, 137 Cs and 90 Sr, both with half-lives of ∼ 30 years, exist in significantly high concentrations.The lifetime of the repository would be extended significantly because all of

Waste transmutation: perspectives

International Nuclear Information System (INIS)

Leray, S.

1997-01-01

After the introduction on the source and nature of nuclear waste, this lecture analyzes the different methods proposed to transmute long-lived isotopes into stable or short-lived isotopes. It is shown that direct methods (photonuclear reactions, spallation, muon catalyzed fusion) do not lead to a sufficient transmutation rate within a reasonable cost. Only the use of hybrid systems, fusion-fission or spallation-fission, can be foreseen. (author)

Transmutation of radioactive nuclear waste

International Nuclear Information System (INIS)

Toor, A; Buck, R

2000-01-01

Lack of a safe disposal method for radioactive nuclear waste (RNW) is a problem of staggering proportion and impact. A typical LWR fission reactor will produce the following RNW in one year: minor actinides (i.e. 237 Np, 242-243 Am, 243-245 Cm) ∼40 kg, long-lived fission products (i.e, 99 Tc, 93 Zr, 129 I, 135 Cs) ∼80 kg, short lived fission products (e.g. 137 Cs, 90 Sr) ∼50kg and plutonium ∼280 kg. The total RNW produced by France and Canada amounts to hundreds of metric tonnes per year. Obtaining a uniform policy dealing with RNW has been blocked by the desire on one hand to harvest the energy stored in plutonium to benefit society and on the other hand the need to assure that the stockpile of plutonium will not be channeled into future nuclear weapons. In the meantime, the quantity and handling of these materials represents a potential health hazard to the world's population and particularly to people in the vicinity of temporary storage facilities. In the U.S., societal awareness of the hazards associated with RNW has effectively delayed development of U.S. nuclear fission reactors during the past decade. As a result the U.S. does not benefit from the large investment of resources in this industry. Reluctance to employ nuclear energy has compelled our society to rely increasingly on non-reusable alternative energy sources; coal, oil, and natural gas. That decision has compounded other unresolved global problems such as air pollution, acid rain, and global warming. Relying on these energy sources to meet our increasing energy demands has led the U.S. to increase its reliance on foreign oil; a policy that is disadvantageous to our economy and our national security. RNW can be simplistically thought of as being composed of two principal components: (1) actinides with half lives up to 10 6 years and (2) the broad class of fission fragments with typical half lives of a few hundred years. One approach to the RNW storage problem has been to transmute the

Optimisation of composite metallic fuel for minor actinide transmutation in an accelerator-driven system

Science.gov (United States)

Uyttenhove, W.; Sobolev, V.; Maschek, W.

2011-09-01

A potential option for neutralization of minor actinides (MA) accumulated in spent nuclear fuel of light water reactors (LWRs) is their transmutation in dedicated accelerator-driven systems (ADS). A promising fuel candidate dedicated to MA transmutation is a CERMET composite with Mo metal matrix and (Pu, Np, Am, Cm)O 2-x fuel particles. Results of optimisation studies of the CERMET fuel targeting to increasing the MA transmutation efficiency of the EFIT (European Facility for Industrial Transmutation) core are presented. In the adopted strategy of MA burning the plutonium (Pu) balance of the core is minimized, allowing a reduction in the reactivity swing and the peak power form-factor deviation and an extension of the cycle duration. The MA/Pu ratio is used as a variable for the fuel optimisation studies. The efficiency of MA transmutation is close to the foreseen theoretical value of 42 kg TW -1 h -1 when level of Pu in the actinide mixture is about 40 wt.%. The obtained results are compared with the reference case of the EFIT core loaded with the composite CERCER fuel, where fuel particles are incorporated in a ceramic magnesia matrix. The results of this study offer additional information for the EFIT fuel selection.

Optimisation of composite metallic fuel for minor actinide transmutation in an accelerator-driven system

International Nuclear Information System (INIS)

Uyttenhove, W.; Sobolev, V.; Maschek, W.

2011-01-01

A potential option for neutralization of minor actinides (MA) accumulated in spent nuclear fuel of light water reactors (LWRs) is their transmutation in dedicated accelerator-driven systems (ADS). A promising fuel candidate dedicated to MA transmutation is a CERMET composite with Mo metal matrix and (Pu, Np, Am, Cm)O 2-x fuel particles. Results of optimisation studies of the CERMET fuel targeting to increasing the MA transmutation efficiency of the EFIT (European Facility for Industrial Transmutation) core are presented. In the adopted strategy of MA burning the plutonium (Pu) balance of the core is minimized, allowing a reduction in the reactivity swing and the peak power form-factor deviation and an extension of the cycle duration. The MA/Pu ratio is used as a variable for the fuel optimisation studies. The efficiency of MA transmutation is close to the foreseen theoretical value of 42 kg TW -1 h -1 when level of Pu in the actinide mixture is about 40 wt.%. The obtained results are compared with the reference case of the EFIT core loaded with the composite CERCER fuel, where fuel particles are incorporated in a ceramic magnesia matrix. The results of this study offer additional information for the EFIT fuel selection.

TRANSMUTED EXPONENTIATED EXPONENTIAL DISTRIBUTION

OpenAIRE

MEROVCI, FATON

2013-01-01

In this article, we generalize the exponentiated exponential distribution using the quadratic rank transmutation map studied by Shaw etal. [6] to develop a transmuted exponentiated exponential distribution. Theproperties of this distribution are derived and the estimation of the model parameters is discussed. An application to real data set are finally presented forillustration

Transmutation of fission products through accelerator

International Nuclear Information System (INIS)

Nakamura, H.; Tani, S.; Takahashi, T.; Yamamura, O.

1995-01-01

The transmutation of fission products through particle accelerators has been studied under the OMEGA program. The photonuclear reaction has also been investigated to be applied to transmuting long-lived fission products, such as Cesium and Strontium, which have difficulties on reaction with neutrons due to its so small cross section. It is applicable for the transmutation if the energy balance can be improved with a monochromatic gamma rays in the range of the Giant Dipole Resonance generated through an excellent high current electron linear accelerator. The feasibility studies are being conducted on the transmutation system using it through an electron accelerator. (authors)

French fuel cycle strategy and partitioning and transmutation programme

International Nuclear Information System (INIS)

Pradel, Ph.

2007-01-01

The global energy context pleads in favour of a sustainable development of nuclear energy since the demand for energy will likely increase, whereas resources will tend to get scarcer and the prospect of global warming will drive down the consumption of fossil fuel sources. How we deal with radioactive waste is crucial in this context. The production of nuclear energy in France has been associated, since its inception, with the optimisation of radioactive waste management, including the partitioning and the recycling of recoverable energetic materials. The public's concern regarding long-term waste management led the French government to prepare and pass the Law of December 1991, requesting in particular the study for fifteen years of solutions to minimising even further the quantity and the hazardousness of final waste, via partitioning and transmutation. At the end of these fifteen years of research, it is considered that partitioning techniques which have been validated on real solutions are at disposal. Indeed, aqueous process for separation of minor actinides from the PUREX raffinate has been brought to a point where there is reasonable assurance that industrial deployment can be successful. A key experiment has been the kilogram-scale successful trials in the CEA-Marcoule Atalante facility in 2005 and this result, together with the results obtained in the frame of the successive European projects, constitutes a considerable step forward. For transmutation, CEA has conducted programmes proving the feasibility of the elimination of minor actinides and fission products: fabrication of specific targets and fuels for transmutation tests in the HFR and Phenix reactors, neutronics and technology studies for critical reactors and ADS developments. Scenario studies have also allowed assessing the feasibility, at the level of cycle and fuel facilities, and the efficiency of transmutation in terms of the quantitative reduction of the final waste inventory depending of

Status of the French Research on Partitioning and Transmutation

International Nuclear Information System (INIS)

Warin, Dominique

2007-01-01

The global energy context pleads in favor of a sustainable development of nuclear energy since the demand for energy will likely increase, whereas resources will tend to get scarcer and the prospect of global warming will drive down the consumption of fossil fuel sources. How we deal with radioactive waste is crucial in this context. The production of nuclear energy in France has been associated, since its inception, with the optimization of radioactive waste management, including the partitioning and the recycling of recoverable energetic materials. The public's concern regarding the long-term waste management made the French Government prepare and pass the December 1991 Law, requesting in particular, the study for fifteen years of solutions for still minimizing the quantity and the hazardousness of final waste, via partitioning and transmutation. At the end of these fifteen years of research, it is considered that partitioning techniques, which have been validated on real solutions, are at disposal. Indeed, aqueous process for separation of minor actinides from the PUREX raffinate has been brought to a point where there is reasonable assurance that industrial deployment can be successful. A key experiment has been the successful kilogram scale trials in the CEA-Marcoule Atalante facility in 2005 and this result, together with the results obtained in the frame of the successive European projects, constitutes a considerable step forward. For transmutation, CEA has conducted programs proving the feasibility of the elimination of minor actinides and fission products: fabrication of specific targets and fuels for transmutation tests in the HFR and Phenix reactors, neutronics and technology studies for critical reactors and ADS developments. Scenario studies have also allowed assessing the feasibility, at the level of cycle and fuel facilities, and the efficiency of transmutation in terms of the quantitative reduction of the final waste inventory depending of the

Current Status of the Transmutation Reactor Technology and Preliminary Evaluation of Transmutation Performance of the KALIMER Core

Energy Technology Data Exchange (ETDEWEB)

Hong, Ser Gi; Sim, Yoon Sub; Kim, Yeong Il; Kim, Young Gyum; Lee, Byung Woon; Song, Hoon; Lee, Ki Bog; Jang, Jin Wook; Lee, Dong Uk

2005-08-15

Recently the most countries using the nuclear power plants for electricity generation have been faced with the problem of the preparation of the repository for the disposition of the nuclear waste generated from LWR. It was well-known that the issues related with long term risk of the radioactive wastes for the future generations are due only to 1% of the total waste. This small fraction of 1% consists of transuranic (TRU) nuclides such as Pu, Np, Am, Cm and the long lived fission products such as Tc and I. For the transuranic (TRU) nuclides, their half lives range from several years to several hundred thousands years and hence their radioactive toxicity can be lasted over very long time period. This has made the change of the rule of the fast spectrum reactor from the economical use of uranium resource through breeding to the reduction of the nuclear waste through the transmutation. The purpose of this study is to obtain the basic knowledge on the nuclear transmutation technology and to suggest the technical solution ways for the future technology development and enhancement through a survey of the state-of-art of the international research on the nuclear transmutation. The increase of the transmutation rate requires the reduction of the breeding ratio. In fact, the transmutation rate is determined by the breeding ratio. The reduction of the breeding ratio can be achieved by reducing the U-238 content in fuel or increasing the neutron leakage through core boundary or absorbing the neutrons by using some absorbers. However, the reduction of the U-238 content results in the degradation of the fuel Doppler coefficient that is one of the most important safety-related parameters and the reduction of the effective delayed neutron fraction that is related with the controllability of the reactor core. Also, the increase of the transmutation rate can lead to the increase of the coolant void reactivity worth unless some ways to reduce the coolant void reactivity are not

Partitioning and Transmutation - Physics, Technology and Politics

International Nuclear Information System (INIS)

Gudowski, W.

2002-01-01

Nuclear reactions can be effectively used to destroy radio toxic isotopes through transmutation processes transforming those isotopes into less radio toxic or stable ones Spent nuclear fuel, a mixture of many isotopes with some of them being highly radio toxic for many hundred thousands of years, may be effectively transmuted through nuclear reactions with neutrons. In a dedicated, well designed transmutation system one can, in principle, reduce the radiotoxicity of the spent nuclear fuel to a level, which will require isolation from the biosphere for the period of time for which engineered barriers can be constructed and licensed (not more than 1-2 thousands of years). En effective transmutation process can not be achieved without a suitable partitioning. Only partitioning of the spent nuclear fuel into predetermined groups of elements makes possible an effective use of neutrons to transmute long-lived radioactive isotopes into short-lived or stable one. However, most of the chemical separation/partitioning processes are element- not isotope-specific, therefore the transmutation of the elements with an existing isotope composition is a typical alternative for transmutation processes. Isotope-specific separation is possible but still very expensive and technologically not matured

Transmutations for Strings

Directory of Open Access Journals (Sweden)

Amin Boumenir

2008-07-01

Full Text Available We investigate the existence and representation of transmutations, also known as transformation operators, for strings. Using measure theory and functional analytic methods we prove their existence and study their representation. We show that in general they are not close to unity since their representation does not involve a Volterra operator but rather the eigenvalue parameter. We also obtain conditions under which the transmutation is either a bounded or a compact operator. Explicit examples show that they cannot be reduced to Volterra type operators.  

Chemical separations schemes for partitioning and transmutation systems

International Nuclear Information System (INIS)

Laidler, J.

2002-01-01

In the initial phase of the U.S. Accelerator Transmutation of Waste (ATW) program, a single-tier system was foreseen in which the transuranics and long-lived fission products (specifically, 99 Tc and 129 I) recovered from spent LWR oxide fuel would be sent directly to an accelerator-driven transmuter reactor [1]. Because the quantity of fuel to be processed annually was so large (almost 1,500 tons per year), an aqueous solvent extraction process was chosen for LWR fuel processing. Without the need to separate transuranics from one another for feed to the transmuter, it became appropriate to develop an advanced aqueous separations method that became known as UREX. The UREX process employs an added reagent (acetohydroxamic acid) that suppresses the extraction of plutonium and promotes the extraction of technetium together with uranium. Technetium can then be efficiently removed from the uranium; the recovered uranium, being highly decontaminated, can be disposed of as a low-level waste or stored in an unshielded facility for future use. Plutonium and the other transuranic elements, plus the remaining fission products, are directed to the liquid waste stream. This stream is calcined, converting the transuranics and fission products to their oxides. The resulting oxide powder, now representing only about four percent of the original mass of the spent fuel, is reduced to metallic form by means of a pyrometallurgical process. Subsequently, the transuranics are separated from the fission products in another pyro-metallurgical step involving molten salt electrorefining

Decay and Transmutation of Nuclides

CERN Document Server

Aarnio, Pertti A

1999-01-01

We present a computer code DeTra which solves analytically the Bateman equations governing the decay, build-up and transmutation of radionuclides. The complexity of the chains and the number of nuclides are not limited. The nuclide production terms considered include transmutation of the nuclides inside the chain, external production, and fission. Time dependent calculations are possible since all the production terms can be re-defined for each irradiation step. The number of irradiation steps and output times is unlimited. DeTra is thus able to solve any decay and transmutation problem as long as the nuclear data i.e. decay data and production rates, or cross sections, are known.

Transmutation of nuclear waste. Status report RAS programme 1994: Recycling and transmutation of actinides and fission products

Energy Technology Data Exchange (ETDEWEB)

Cordfunke, E H.P.; Gruppelaar, H; Franken, W M.P.

1995-07-01

This report describes the status and progress of the Dutch RAS programme on `Recycling and Transmutation of Actinides and Fission Products` over the year 1994, which is the first year of the second 4-year programme. This programme is outlined and a short progress report is given over 1994, including a listing of 23 reports and publications over the year 1994. Highlights of 1994 were: The completion of long-lived fission-product transmutation studies, the initiation of small-scale demonstration experiments in the HFR on Tc and I, the issue of reports on the potential of the ALMR (Advanced Liquid Metal Reactor) for transmutation adn the participation and international cooperation on irradiation experiments with actinides in inert matrices. The remaining chapters contain more extended contributions on recent developments and selected topics, under the headings: Benefits and risks of partitioning and transmutation, Perspective of chemical partitioning, Inert matrices, Evolutionary options (MOX), Perspective of heavy water reactors, Perspective of fast burners, Perspective of accelerator-based systems, Thorium cycle, Fission-product transmutation, End scenarios, and Executive summary and recommendations. (orig.).

Transmutation of nuclear waste. Status report RAS programme 1994: Recycling and transmutation of actinides and fission products

International Nuclear Information System (INIS)

Cordfunke, E.H.P.; Gruppelaar, H.; Franken, W.M.P.

1995-07-01

This report describes the status and progress of the Dutch RAS programme on 'Recycling and Transmutation of Actinides and Fission Products' over the year 1994, which is the first year of the second 4-year programme. This programme is outlined and a short progress report is given over 1994, including a listing of 23 reports and publications over the year 1994. Highlights of 1994 were: The completion of long-lived fission-product transmutation studies, the initiation of small-scale demonstration experiments in the HFR on Tc and I, the issue of reports on the potential of the ALMR (Advanced Liquid Metal Reactor) for transmutation adn the participation and international cooperation on irradiation experiments with actinides in inert matrices. The remaining chapters contain more extended contributions on recent developments and selected topics, under the headings: Benefits and risks of partitioning and transmutation, Perspective of chemical partitioning, Inert matrices, Evolutionary options (MOX), Perspective of heavy water reactors, Perspective of fast burners, Perspective of accelerator-based systems, Thorium cycle, Fission-product transmutation, End scenarios, and Executive summary and recommendations. (orig.)

Evaluation of actinide partitioning and transmutation in light-water reactors

International Nuclear Information System (INIS)

Collins, Emory D.; Renier, John-Paul

2004-01-01

Advanced Fuel Cycle Initiative (AFCI) studies were made to evaluate the feasibility of multicycle transmutation of plutonium and the minor actinides (MAs) in light-water reactors (LWRs). Results showed that significant repository benefits, cost reductions, proliferation resistance, and effective use of facilities can be obtained. Key advantages are shown to be made possible by processing 30-year-decayed spent fuel rather than the more traditional 5-year-decayed fuel. (authors)

Actinide and fission product partitioning and transmutation

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

The fourth international information exchange meeting on actinide and fission product partitioning and transmutation, took place in Mito City in Japan, on 111-13 September 1996. The proceedings are presented in six sessions: the major programmes and international cooperation, the partitioning and transmutation programs, feasibility studies, particular separation processes, the accelerator driven transmutation, and the chemistry of the fuel cycle. (A.L.B.)

Transmutations of nuclear waste. Progress report RAS programme 1995: Recycling and transmutation of actinides and fission products

International Nuclear Information System (INIS)

Gruppelaar, H.; Cordfunke, E.H.P.; Konings, R.J.M.; Bultman, J.H.; Dodd, D.H.; Franken, W.M.P.; Kloosterman, J.L.; Koning, A.J.; Wichers, V.A.

1996-04-01

This report describes the progress of the Dutch RAS programme on 'Recycling and Transmutation of Actinides and Fission Products' over the year 1995, which is the second year of the 4-year programme 1994-1997. An extensive listing of reports and publications from 1991 to 1995 is given. Highlights in 1995 were: -The completion of the European Strategy Study on Nuclear Waste Transmutation as a result of which the understanding of transmutation of plutonium, minor actinides and long-lived fission products in thermal and fast reactors has been increased significantly. Important ECN contributions were given on Am, 99 Tc and 129 I transmutation options. Follow-up contracts have been obtained for the study of 100% MOX cores and accelerator-based transmutation. - Important progress in the evaluation of CANDU reactors for burning very large amounts of transuranium mixtures in inert matrices. - The first RAS irradiation experiment in the HFR, in which the transmutation of technetium and iodine was examined, has been completed and post-irradiation examination has been started. - A joint proposal of the EFTTRA cooperation for the 4 th Framework Programme of the EU, to demonstrate the feasibility of the transmutation of americium in an inert matrix by an irradiation in the HFR, has been granted. - A bilateral contract with CEA has been signed to participate in the CAPRA programme, and the work in this field has been started. - The thesis work on Actinide Transmutation in Nuclear Reactor Systems was succesfully defended. New PhD studies on Pu burning in HTGR, on nuclear data for accelerator-based systems, and on the SLM-technique for separation of actinides were started. - A review study of the use of the thorium cycle as a means for nuclear waste reduction, has been completed. A follow-up of this work is embedded in an international project for the 4th Framework Programme of the EU. (orig./DG)

Research activities related to accelerator-based transmutation at PSI

International Nuclear Information System (INIS)

Wydler, P.

1993-01-01

Transmutation of actinides and fission products using reactors and other types of nuclear systems may play a role in future waste management schemes. Possible advantages of separation and transmutation are: volume reductions, the re-use of materials, the avoidance of a cumulative risk, and limiting the duration of the risk. With its experience in reactor physics, accelerator-based physics, and the development of the SINQ spallation neutron source, PSI is in a good position to perform basic theoretical and experimental studies relating to the accelerator-based transmutation of actinides. Theoretical studies at PSI have been concentrated, so far, on systems in which protons are used directly to transmute actinides. With such systems and appropriate recycling schemes, the studies showed that considerable reduction factors for long-term toxicity can be obtained. With the aim of solving some specific data and method problems related to these types of systems, a programme of differential and integral measurements at the PSI ring accelerator has been initiated. In a first phase of this programme, thin samples of actinides will be irradiated with 590 MeV protons, using an existing irradiation facility. The generated spallation and fission products will be analysed using different experimental techniques, and the results will be compared with theoretical predictions based on high-energy nucleon-meson transport calculations. The principal motivation for these experiments is to resolve discrepancies observed between calculations based on different high-energy fission models. In a second phase of the programme, it is proposed to study the neutronic behaviour of multiplying target-blanket assemblies with the help of zero-power experiments set up at a separate, dedicated beam line of the accelerator. (author) 3 figs., 2 tabs., 8 refs

Recycling and transmutation of nuclear waste. ECN-Petten and Belgonucleaire contributions in the framework of 'Partitioning and transmutation studies of the 4th CEC programme on rad waste management and disposal'

International Nuclear Information System (INIS)

Abrahams, K.; Kloosterman, J.L.; Gruppelaar, H.; Brusselaers, P.; Evrard, G.; La Fuente, A.; Maldague, T.; Pilate, S.; Renard, A.

1995-12-01

A 'Strategy study on nuclear waste transmutation' by Netherlands Energy Research Foundation (ECN) and Belgonucleaire (BN) in the frame of the EU R and D Programme 1990/1994 on management and storage of radioactive waste has been executed in collaboration with AEA Technology, CEA and Siemens. First of all the motivation for transmuting long-lived radioactive products has been formulated, next transmutation of Tc-99 and I-129 in fission reactors has been studied for the PWR, HFR, Superphenix, and the CANDU reactor. Cross section libraries have been improved for ORIGEN-S on the basis of JEF2.2 and EAF3. This study has been amended by a graphical representation of important reactions for activation of cladding and inert matrix materials. By means of the derived new data libraries, some sample calculations on transmutation of americium in thermal reactors have been performed. Implications of recycling plutonium and americium in the form of MOX fuel in light water reactors have been investigated. It became clear from the present study that trasmutation of the existing plutonium has the highest priority and that reduction of minor-actinides is next on the priority list. Thirdly, the (difficult) large-scale transmutation of Tc-99 and of I-129 could reduce the leakage dose risks. It also seems most worthwhile to be careful with naturally occurring U-234 in the waste, as this will in the long run lead to a substantial increase of the 'natural' radon dose in the neighbourhood of the storage facility. (orig.)

Recycling and transmutation of nuclear waste. ECN-Petten and Belgonucleaire contributions in the framework of `Partitioning and transmutation studies of the 4th CEC programme on rad waste management and disposal`

Energy Technology Data Exchange (ETDEWEB)

Abrahams, K. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Kloosterman, J.L. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Gruppelaar, H. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Brusselaers, P. [Belgonucleaire S.A., Brussels (Belgium); Evrard, G. [Belgonucleaire S.A., Brussels (Belgium); La Fuente, A. [Belgonucleaire S.A., Brussels (Belgium); Maldague, T. [Belgonucleaire S.A., Brussels (Belgium); Pilate, S. [Belgonucleaire S.A., Brussels (Belgium); Renard, A. [Belgonucleaire S.A., Brussels (Belgium)

1995-12-01

A `Strategy study on nuclear waste transmutation` by Netherlands Energy Research Foundation (ECN) and Belgonucleaire (BN) in the frame of the EU R and D Programme 1990/1994 on management and storage of radioactive waste has been executed in collaboration with AEA Technology, CEA and Siemens. First of all the motivation for transmuting long-lived radioactive products has been formulated, next transmutation of Tc-99 and I-129 in fission reactors has been studied for the PWR, HFR, Superphenix, and the CANDU reactor. Cross section libraries have been improved for ORIGEN-S on the basis of JEF2.2 and EAF3. This study has been amended by a graphical representation of important reactions for activation of cladding and inert matrix materials. By means of the derived new data libraries, some sample calculations on transmutation of americium in thermal reactors have been performed. Implications of recycling plutonium and americium in the form of MOX fuel in light water reactors have been investigated. It became clear from the present study that trasmutation of the existing plutonium has the highest priority and that reduction of minor-actinides is next on the priority list. Thirdly, the (difficult) large-scale transmutation of Tc-99 and of I-129 could reduce the leakage dose risks. It also seems most worthwhile to be careful with naturally occurring U-234 in the waste, as this will in the long run lead to a substantial increase of the `natural` radon dose in the neighbourhood of the storage facility. (orig.).

Impact of Transmutation Scenarios on Fuel Transportation

International Nuclear Information System (INIS)

Saturnin, A.; Duret, B.; Allou, A.; Jasserand, F.; Fillastre, E.; Giffard, F.X.; Chabert, C.; Caron-Charles, M.; Garzenne, C.; Laugier, F.

2015-01-01

Minor actinides transmutation scenarios have been studied in the frame of the French Sustainable Radioactive Waste Management Act of 28 June 2006. Transmutation scenarios supposed the introduction of a sodium-cooled fast reactor fleet using homogeneous or heterogeneous recycling modes for the minor actinides. Americium, neptunium and curium (MA) or americium alone (Am) can be transmuted together in a homogeneous way embedded in FR-MOX fuel or incorporated in MA or Am-Bearing radial Blankets (MABB or AmBB). MA transmutation in Accelerator Driven System has also been studied while plutonium is being recycled in SFR. Assessments and comparisons of these advanced cycles have been performed considering technical and economic criteria. Transportation needs for fresh and used transmutation fuels is one of these criteria. Transmutation fuels have specific characteristics in terms of thermal load and neutron emissions. Thermal, radiation and criticality constraints have been taken into account in this study to suggest cask concepts for routine conditions of transport, to estimate the number of assemblies to be transported in a cask and the number of annual transports. Comparison with the no transmutation option, i.e. management of uranium and plutonium in SFRs, is also presented. Regarding these matters, no high difficulties appear for assemblies with limited content of Am (homogeneous or heterogeneous recycling modes). When fuels contain curium, technical transport uncertainties increase because of the important heat release requiring dividing fresh fuels and technological innovations development (MABB and ADS). (authors)

Status of the French research programme for actinides and fission products partitioning and transmutation

International Nuclear Information System (INIS)

Warin, D.

2003-01-01

The paper focus on separation and transmutation research and development programme and main results over these ten last years. The massive research programme on enhanced separation, conducted by CEA and supported by broad international cooperation, has recently achieved some vital progress. Based on real solutions derived from the La Hague process, the CEA demonstrated the lab-scale feasibility of extracting minor actinides and some fission products (I, Cs and Tc) using an hydrometallurgical process that can be extrapolated on the industrial scale. The CEA also conducted programmes proving the technical feasibility of the elimination of minor actinides and fission products by transmutation: fabrication of specific targets and fuels for transmutation tests in the HFR and Phenix reactors, neutronics and technology studies for ADS developments in order to support the MEGAPIE, TRADE and MYRRHA experiments and the future 100 MW international ADS demonstrator. Scenarios studies aimed at stabilizing the inventory with long-lived radionuclides, plutonium, minor actinides and certain long-lived fission products in different nuclear power plant parks and to verify the feasibility at the level of the cycle facilities and fuels involved in those scenarios. Three French Research Groups CEA-CNRS carry out partitioning (PRACTIS) and transmutation (NOMADE and GEDEON) more basic studies. (author)

Transmutation of 129I Using an Accelerator-Driven System

International Nuclear Information System (INIS)

Nishihara, Kenji; Takano, Hideki

2002-01-01

A conceptual blanket design for 129 I transmutation is proposed for an accelerator-driven system (ADS) that is designed to transmute minor actinides (MAs). In this ADS, 250 kg/yr of MA and 56 kg/yr of iodine are simultaneously transmuted, and they correspond to the quantities generated from ∼10 units of existing light water reactors. Furthermore, an introduction scenario and the benefit of iodine transmutation are studied for future introduction of fast breeder reactors. It is shown that the transmutation of iodine benefits the concept of underground disposal

Minor actinide transmutation on PWR burnable poison rods

International Nuclear Information System (INIS)

Hu, Wenchao; Liu, Bin; Ouyang, Xiaoping; Tu, Jing; Liu, Fang; Huang, Liming; Fu, Juan; Meng, Haiyan

2015-01-01

Highlights: • Key issues associated with MA transmutation are the appropriate loading pattern. • Commercial PWRs are the only choice to transmute MAs in large scale currently. • Considerable amount of MA can be loaded to PWR without disturbing k eff markedly. • Loading MA to PWR burnable poison rods for transmutation is an optimal loading pattern. - Abstract: Minor actinides are the primary contributors to long term radiotoxicity in spent fuel. The majority of commercial reactors in operation in the world are PWRs, so to study the minor actinide transmutation characteristics in the PWRs and ultimately realize the successful minor actinide transmutation in PWRs are crucial problem in the area of the nuclear waste disposal. The key issues associated with the minor actinide transmutation are the appropriate loading patterns when introducing minor actinides to the PWR core. We study two different minor actinide transmutation materials loading patterns on the PWR burnable poison rods, one is to coat a thin layer of minor actinide in the water gap between the zircaloy cladding and the stainless steel which is filled with water, another one is that minor actinides substitute for burnable poison directly within burnable poison rods. Simulation calculation indicates that the two loading patterns can load approximately equivalent to 5–6 PWR annual minor actinide yields without disturbing the PWR k eff markedly. The PWR k eff can return criticality again by slightly reducing the boric acid concentration in the coolant of PWR or removing some burnable poison rods without coating the minor actinide transmutation materials from PWR core. In other words, loading minor actinide transmutation material to PWR does not consume extra neutron, minor actinide just consumes the neutrons which absorbed by the removed control poisons. Both minor actinide loading patterns are technically feasible; most importantly do not need to modify the configuration of the PWR core and

Transmutation of long-lived fission products

International Nuclear Information System (INIS)

Abrahams, K.

1994-01-01

The time-accumulated dose related to technetium dominates the leakage doses in most scenarios for imperturbed geological disposal. If human intrusion into geologically stable repositories or other disturbances is taken into account, the actinides determine the maximum value of the expected individual dose rates of shorter storage times. Therefore actinides dominate the discussion on transmutation of nuclear waste. In principle current LWRs could be used for a massive transmutation of Tc and perhaps I. Fast reactors and HWRs have attractive potential with respect to transmutation in moderated assemblies. HWRs like CANDU have easy refuelling possibilities. (orig.)

Transmutation of Tc-99 in fission reactors

International Nuclear Information System (INIS)

Kloosterman, J.L.; Li, J.M.

1994-12-01

Transmutation of Tc-99 in three different types of fission reactors is considered: A heavy water reactor, a fast reactor and a light water reactor. For the first type a CANDU reactor was chosen, for the second one the Superphenix reactor, and for the third one a PWR. The three most promising Tc-99 transmuters are the fast reactor with a moderated subassembly in the inner core, a fast reactor with a non-moderated subassembly in the inner core, and a heavy water reactor with Tc-99 target pins in the moderator between the fuel bundles. Transmutation half lives of 15 to 25 years can be achieved, with yearly transmuted Tc-99 masses of about 100 kg at a thermal reactor power of about 3000 MW. (orig.)

Transmutation of minor actinide using thorium fueled BWR core

International Nuclear Information System (INIS)

Susilo, Jati

2002-01-01

One of the methods to conduct transmutation of minor actinide is the use of BWR with thorium fuel. Thorium fuel has a specific behaviour of producing a little secondary minor actinides. Transmutation of minor actinide is done by loading it in the BWR with thorium fuel through two methods, namely close recycle and accumulation recycle. The calculation of minor actinide composition produced, weigh of minor actinide transmuted, and percentage of reminder transmutation was carried SRAC. The calculations were done to equivalent cell modeling from one fuel rod of BWR. The results show that minor actinide transmutation is more effective using thorium fuel than uranium fuel, through both close recycle and accumulation recycle. Minor actinide transmutation weight show that the same value for those recycle for 5th recycle. And most of all minor actinide produced from 5 unit BWR uranium fuel can transmuted in the 6 t h of close recycle. And, the minimal value of excess reactivity of the core is 12,15 % Δk/k, that is possible value for core operation

Physical studies of transmutation scenarios. The Muse program with the Masurca facility: a step towards an hybrid demonstrator?

International Nuclear Information System (INIS)

Bouchard, J.; Leconte, Ph.; Doubre, H.; Bhatnagar, V.P.; Carbonnier, J.L.; Chawla, R.; Bernard, H.

2002-01-01

The Muse research program, which started in 1995, is a contribution to the development of a dedicated subcritical accelerator driven system (ADS) for the transmutation of minor actinides produced by conventional nuclear power plants. The Muse experiments aim at making a parametric study of different reactor core compositions with different subcritical levels and supplied by different sources in order to demonstrate that the measurement techniques and the calculation charts established for critical FBRs remain valid with an hybrid system. The 4. phase of the Muse program concerns the design, realization and installation of the Genepi (generator of intense pulse neutrons) deutons accelerator at the Masurca facility of Cadarache (France) for the understanding of the neutronic behaviour of an ADS, the definition of a reference calculation scheme, and the development of specific experimental techniques for dynamical measurements. This document brings together the presentations (transparencies) given at the SFEN technical meeting of May 30, 2002 about the Muse program. (J.S.)

Transmuted Generalized Inverse Weibull Distribution

OpenAIRE

Merovci, Faton; Elbatal, Ibrahim; Ahmed, Alaa

2013-01-01

A generalization of the generalized inverse Weibull distribution so-called transmuted generalized inverse Weibull dis- tribution is proposed and studied. We will use the quadratic rank transmutation map (QRTM) in order to generate a flexible family of probability distributions taking generalized inverse Weibull distribution as the base value distribution by introducing a new parameter that would offer more distributional flexibility. Various structural properties including explicit expression...

Transmutation blanket design for a Tokamak system

International Nuclear Information System (INIS)

Velasquez, Carlos E.; Barros, Graiciany de P.; Pereira, Claubia; Veloso, Maria A. Fortini; Costa, Antonella L.

2011-01-01

Sub-critical advanced reactor with a D-T fusion neutron source based on Tokamak technology is an innovative type of nuclear system. Due to the high quantity of neutrons produced by fusion reactions, it could be well spent in the transmutation process of the transuranic elements. Nevertheless, to achieve a successful transmutation, it is necessary to know the neutron fluence along the radial axis and its characteristics. In this work, it evaluated the neutron flux and interaction frequency along the radial axis changing the material of the first wall. W-alloy, beryllium and the combination of both were studied and regions more suitable to transmutation were determined. The results demonstrated that the better zone to place a transmutation blanket is limited by the heat sink and the shield block. Material arrangements W-alloy/W-alloy and W-alloy/Beryllium would be able to hold the requirements of high fluence and hardening spectrum needed to transuranic transmutation. The system was simulated using the MCNP5 code, the ITER Final Design Report, 2001, and the FENDL/MC-2.1 nuclear data library. (author)

Study on multi-recycle transmutation of LLFP in light water reactor

International Nuclear Information System (INIS)

Setiawan, M.B.; Kitamoto, A.

2001-01-01

The effectiveness of transmutation for long-lived fission products (LLFP) in light water reactors (LWR), i.e. both BWR and PWR, considering the large capture cross-section of FPs in thermal region was evaluated. Calculation results of iodine and technetium transmutation in BWR and PWR suggested an effective use of BWR as compared to PWR. To obtain transmutation fraction [TF] of 30 to 40%, the irradiation period needed for 99 Tc transmutation was estimated as 10 to 15 years, and the period for 129 I transmutation was estimated as 30 to 40 years, respectively. The evaluations bring a new concept of multi-recycle LLFP transmutation using LWR TR (LWR for transmutation)

Actinide and Fission Product Partitioning and Transmutation

International Nuclear Information System (INIS)

2015-06-01

The benefits of partitioning and transmutation (P and T) have now been established worldwide and, as a result, many countries are pursuing R and D programmes to advance the technologies associated with P and T. In this context, the OECD Nuclear Energy Agency (NEA) has organised a series of biennial information exchange meetings to provide experts with a forum to present and discuss state-of-the-art developments in the field of partitioning and transmutation since 1990. The OECD Nuclear Energy Agency Information Exchange Meeting on Actinides and Fission Products Partitioning and Transmutation is a forum for experts to present and discuss the state-of-the-art development in the field of P and T. Thirteen meetings have been organised so far and held in Japan, the United States, France, Belgium, Spain, the Republic of Korea and the Czech Republic. This 13. meeting was hosted by Seoul National University (Seoul, Republic of Korea) and was organised in co-operation with the International Atomic Energy Agency (IAEA) and the European Community (EC). The meeting covered strategic and scientific developments in the field of P and T such as: fuel cycle strategies and transition scenarios, the role of P and T in the potential evolution of nuclear energy as part of the future energy mix; radioactive waste management strategies; transmutation fuels and targets; advances in pyro and aqueous separation processes; P and T specific technology requirements (materials, spallation targets, coolants, etc.); transmutation systems: design, performance and safety; impact of P and T on the fuel cycle; fabrication, handling and transportation of transmutation fuels. A total of 103 presentations (39 oral and 64 posters) were discussed among the 110 participants from 19 countries and 2 international organisations. The meeting consisted of one plenary session where national and international programmes were presented followed by 5 technical sessions: - Fuel Cycle Strategies and Transition

Development of nuclear transmutation technology for transuranic elements

International Nuclear Information System (INIS)

Mukaiyama, Takehiko

1996-01-01

Partitioning and Transmutation (P-T) of long-lived radioactive nuclides is conceived as the technology to improve the high-level radioactive waste management. This report discusses the incentives of P-T, generation of long-lived nuclides in fission reactors, nuclear transmutation technologies, R and D activities of the partitioning and transmutation technology development programs at JAERI and in the world. (author)

Partitioning and transmutation. Annual Report 1997

Energy Technology Data Exchange (ETDEWEB)

Enarsson, Aa; Landgren, A; Liljenzin, J O; Skaalberg, M; Spjuth, L [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Chemistry

1997-12-01

The current research project on partitioning and transmutation at the Dept. of Nuclear Chemistry, CTH, has the primary objective to investigate separation processes useful in connection with transmutation of long-lived radionuclides in high level nuclear waste. Partitioning is necessary in order to recover and purify the elements before and after each irradiation in a P and T treatment. In order to achieve a high transmutation efficiency the chemical separation process used must have small losses to various waste streams. At present, only aqueous based separation processes are known to be able to achieve the high recovery and separation efficiencies necessary for a useful P and T process. Refs, figs, tabs.

Transmutation doping of silicon solar cells

Science.gov (United States)

Wood, R. F.; Westbrook, R. D.; Young, R. T.; Cleland, J. W.

1977-01-01

Normal isotopic silicon contains 3.05% of Si-30 which transmutes to P-31 after thermal neutron absorption, with a half-life of 2.6 hours. This reaction is used to introduce extremely uniform concentrations of phosphorus into silicon, thus eliminating the areal and spatial inhomogeneities characteristic of chemical doping. Annealing of the lattice damage in the irradiated silicon does not alter the uniformity of dopant distribution. Transmutation doping also makes it possible to introduce phosphorus into polycrystalline silicon without segregation of the dopant at the grain boundaries. The use of neutron transmutation doped (NTD) silicon in solar cell research and development is discussed.

Actinide and fission product separation and transmutation

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-07-01

The second international information exchange meeting on actinide and fission product separation and transmutation, took place in Argonne National Laboratory in Illinois United States, on 11-13 November 1992. The proceedings are presented in four sessions: Current strategic system of actinide and fission product separation and transmutation, progress in R and D on partitioning processes wet and dry, progress in R and D on transmutation and refinements of neutronic and other data, development of the fuel cycle processes fuel types and targets. (A.L.B.)

Minor actinides transmutation performance in a fast reactor

International Nuclear Information System (INIS)

Takeda, Toshikazu

2016-01-01

Highlights: • A method for calculating MA transmutation for individual nuclides has been proposed by introducing two formulas of the MA transmutation. One corresponds to the difference of MA amounts, and the other corresponds to the sum of the fission amounts and the plutonium production amounts. • Using the method the MA transmutation was calculated for Np-237 and Am-241 in a fast reactor. The burnup period was changed from 1 year to 12 year. • For the 1 year burnup a large amount of Am-242m, Cm-242 are produced from Am-241. The total MA transmutation amount increases with burnup time, but its gradient with respect to burnup time decreases after 9 years, and the transmutation amount by overall fission increases almost linearly with burnup time. • However, after the 6 year burnup the fission contribution became large because of the large production of Pu isotopes from the original Am-241. • In addition to the homogeneous loading of the MA nuclides into the cores, a heterogeneous loading of Am-241 to the blanket region was considered. - Abstract: Results obtained in the project named “Study on Minor Actinides Transmutation using Monju Data”, which has been sponsored by the Ministry of Education, Culture, Sports, Science and Technology in Japan (MEXT) are described. In order to physically understand transmutation of individual MA nuclides in fast reactors, a new method was developed in which the MAs transmutation is interpreted by two formulas. One corresponds to the difference of individual MA nuclides amounts before and after a burnup period, and the other is the sum of amount of fission of a relevant MA nuclide and the net plutonium production from the MA nuclide during a burnup period. The method has been applied to two fast reactors with MA fuels loaded in cores homogeneously and in a blanket region heterogeneously. Numerical results of MA transmutation for the two reactors are shown.

Neutronic assessment of strontium-90 transmutation in fusion reactors

International Nuclear Information System (INIS)

Parish, T.A.

1979-01-01

Transmutation of 90 Sr using fusion neutrons has been suggested as a possible technique for disposing of this waste nuclide. For transmutation to be attractive, high transmutation rates relative to natural decay are required. Effective half-lives for 90 Sr were computed for fusion reactor blankets constructed of various materials. To obtain satisfactory transmutation rates, fusion reactors with high first wall neutron currents and with highly moderating blankets were found to be necessary. An effective half-life for 90 Sr of 90 Sr inventory and the number of burners required for various fission usage scenarios. Efficient and fast chemical separations were needed to reap the benefits of a short effective half-life. For the fusion burners considered, it was found that the 90 Sr inventory could not be reduced to less than one-fourth of the inventory without transmutation if fission usage continued at a constant rate. Such a reduction is not sufficient to justify the transmutation disposal of 90 Sr

Transmutation Theory in the Greek Alchemical Corpus.

Science.gov (United States)

Dufault, Olivier

2015-08-01

This paper studies transmutation theory as found in the texts attributed to Zosimus of Panopolis, "the philosopher Synesius," and "the philosopher Olympiodorus of Alexandria." It shows that transmutation theory (i.e. a theory explaining the complete transformation of substances) is mostly absent from the work attributed to these three authors. The text attributed to Synesius describes a gilding process, which is similar to those described by Pliny and Vitruvius. The commentary attributed to Olympiodorus is the only text studied here that describes something similar to a transmutation theory. It is unclear, however, if this was a theory of transmutation or if the writer meant something more like the literal meaning of the word "ekstrophē," a term used to describe the transformation of metals, as the "turning inside-out" of what is hidden in a substance. A similar conception of ekstrophē can be found in the works of Zosimus, who discussed transmutation to make an analogy with self-purification processes, which, from the perspective of his own anthropogony, consisted in the "turning inside-out" of the "inner human" (esō anthrōpos).

Program on fuels for transmutation: present status and prospects

Energy Technology Data Exchange (ETDEWEB)

Rouault, J.; Garnier, J.C.; Chauvin, N.; Pillon, S. [CEA Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. d' Etudes des Combustibles

2001-07-01

The performance calculations of appropriate fuel cycle facilities and reactor configurations (scenarios) relying on current reactor technologies (Pressurized Water Reactor and Fast neutrons Reactors) or innovative reactors (Accelerator Driven Systems) have proved the scientific feasibility of some P and T strategies. To insure the technological feasibility, a large program on fuels and materials is underway, including advanced concepts for PWRs and the development of specific targets (dispersed fuels) for transmutation in Fast Reactors. Experiments in different reactors including Phenix are being prepared. The program is presented and recent results are given. (author)

Program on fuels for transmutation: present status and prospects

International Nuclear Information System (INIS)

Rouault, J.; Garnier, J.C.; Chauvin, N.; Pillon, S.

2001-01-01

The performance calculations of appropriate fuel cycle facilities and reactor configurations (scenarios) relying on current reactor technologies (Pressurized Water Reactor and Fast neutrons Reactors) or innovative reactors (Accelerator Driven Systems) have proved the scientific feasibility of some P and T strategies. To insure the technological feasibility, a large program on fuels and materials is underway, including advanced concepts for PWRs and the development of specific targets (dispersed fuels) for transmutation in Fast Reactors. Experiments in different reactors including Phenix are being prepared. The program is presented and recent results are given. (author)

Development and application of new parameters for TRU transmutation effectiveness

International Nuclear Information System (INIS)

Han, Chi Young

2005-02-01

Four new parameters (incineration branching ratio, incineration rate, incineration time, and incineration buckling) have been developed to evaluate quantitatively the TRU transmutation effectiveness and applied to transmutation of uranium and TRU. From the incineration branching ratio, it is possible to analyze the main contributors to fission reaction for transmutation of a target nuclide. From the incineration rate, it is available to evaluate the transmutation effectiveness in the viewpoint of a relative incineration rate to incineration potential of a target nuclide and its family. This parameter is also used to calculate the incineration time and incineration buckling together with the incineration branching ratio. The incineration time makes it possible to discuss more practically the transmutation speed instead of the existing other parameters. The incineration buckling can be used to evaluate the time behavior of the incineration rate and also employed to support the results from the incineration time. Taking into account the transmutation effectiveness and potential of uranium and TRU derived by using the parameters and an existing neutron economy parameter, it was noted that the thermal neutron energy is very preferable from the transmutation effectiveness point of view, on the other hand the fast neutron energy is effective from the transmutation potential. Applying them to the typical critical and subcritical TRU burners, it is indicated that the critical reactor containing fertile uranium undergoes effectively the selective TRU transmutation on the present fast spectrum. It was also noted that the uranium-free subcritical reactor could be operated effectively on a little softer spectrum due to the larger neutron excess in the present spectrum. It is expected that the new parameters developed in this study and the results are directly applicable to practical transmutation reactor design, in particular accelerator-driven transmutation reactor

Copper Doping of Zinc Oxide by Nuclear Transmutation

Science.gov (United States)

2014-03-27

Copper Doping of Zinc Oxide by Nuclear Transmutation THESIS Matthew C. Recker, Captain, USAF AFIT-ENP-14-M-30 DEPARTMENT OF THE AIR FORCE AIR...NUCLEAR TRANSMUTATION THESIS Presented to the Faculty Department of Engineering Physics Graduate School of Engineering and Management Air Force...COPPER DOPING OF ZINC OXIDE BY NUCLEAR TRANSMUTATION Matthew C. Recker, BS Captain, USAF Approved: //signed// 27 February 2014 John W. McClory, PhD

Investigation of the feasibility of a small scale transmutation device

Science.gov (United States)

Sit, Roger Carson

This dissertation presents the design and feasibility of a small-scale, fusion-based transmutation device incorporating a commercially available neutron generator. It also presents the design features necessary to optimize the device and render it practical for the transmutation of selected long-lived fission products and actinides. Four conceptual designs of a transmutation device were used to study the transformation of seven radionuclides: long-lived fission products (Tc-99 and I-129), short-lived fission products (Cs-137 and Sr-90), and selective actinides (Am-241, Pu-238, and Pu-239). These radionuclides were chosen because they are major components of spent nuclear fuel and also because they exist as legacy sources that are being stored pending a decision regarding their ultimate disposition. The four designs include the use of two different devices; a Deuterium-Deuterium (D-D) neutron generator (for one design) and a Deuterium-Tritium (D-T) neutron generator (for three designs) in configurations which provide different neutron energy spectra for targeting the radionuclide for transmutation. Key parameters analyzed include total fluence and flux requirements; transmutation effectiveness measured as irradiation effective half-life; and activation products generated along with their characteristics: activity, dose rate, decay, and ingestion and inhalation radiotoxicity. From this investigation, conclusions were drawn about the feasibility of the device, the design and technology enhancements that would be required to make transmutation practical, the most beneficial design for each radionuclide, the consequence of the transmutation, and radiation protection issues that are important for the conceptual design of the transmutation device. Key conclusions from this investigation include: (1) the transmutation of long-lived fission products and select actinides can be practical using a small-scale, fusion driven transmutation device; (2) the transmutation of long

Some recent contributions of basic nuclear science to nuclear waste transmutation

International Nuclear Information System (INIS)

Schapira, J.P.

2001-01-01

Nuclear waste transmutation aims at alleviating some long-term risks associated with actinides and with some long-lived fission products. Proposals of using accelerator driven system (ADS) to efficiently burn actinides in uranium free fuels have revitalized some basic researches in the field of nuclear and reactor physics. This is the case for high intensity accelerator in the ADS context and for the neutron source which relies to a large extent on basic nuclear physics related to spallation. There is also an experimental program called MUSE at Cadarache to study the sub-critical reactor physics with regard to its neutronics. A second area where basic research is involved is the measurement of new or more reliable neutron cross sections specific to transmutation and also to the thorium fuel cycle considered as a long-term option for ''clean'' energy production with reduced actinide production. This second area will possibly be covered by a new facility called n-TOF developed at CERN. (author)

Apparatus for nuclear transmutation and power production using an intense accelerator-generated thermal neutron flux

Science.gov (United States)

Bowman, Charles D.

1992-01-01

Apparatus for nuclear transmutation and power production using an intense accelerator-generated thermal neutron flux. High thermal neutron fluxes generated from the action of a high power proton accelerator on a spallation target allows the efficient burn-up of higher actinide nuclear waste by a two-step process. Additionally, rapid burn-up of fission product waste for nuclides having small thermal neutron cross sections, and the practicality of small material inventories while achieving significant throughput derive from employment of such high fluxes. Several nuclear technology problems are addressed including 1. nuclear energy production without a waste stream requiring storage on a geological timescale, 2. the burn-up of defense and commercial nuclear waste, and 3. the production of defense nuclear material. The apparatus includes an accelerator, a target for neutron production surrounded by a blanket region for transmutation, a turbine for electric power production, and a chemical processing facility. In all applications, the accelerator power may be generated internally from fission and the waste produced thereby is transmuted internally so that waste management might not be required beyond the human lifespan.

Apparatus for nuclear transmutation and power production using an intense accelerator-generated thermal neutron flux

Science.gov (United States)

Bowman, C.D.

1992-11-03

Apparatus for nuclear transmutation and power production using an intense accelerator-generated thermal neutron flux. High thermal neutron fluxes generated from the action of a high power proton accelerator on a spallation target allows the efficient burn-up of higher actinide nuclear waste by a two-step process. Additionally, rapid burn-up of fission product waste for nuclides having small thermal neutron cross sections, and the practicality of small material inventories while achieving significant throughput derive from employment of such high fluxes. Several nuclear technology problems are addressed including 1. nuclear energy production without a waste stream requiring storage on a geological timescale, 2. the burn-up of defense and commercial nuclear waste, and 3. the production of defense nuclear material. The apparatus includes an accelerator, a target for neutron production surrounded by a blanket region for transmutation, a turbine for electric power production, and a chemical processing facility. In all applications, the accelerator power may be generated internally from fission and the waste produced thereby is transmuted internally so that waste management might not be required beyond the human lifespan.

Transmuted Complementary Weibull Geometric Distribution

Directory of Open Access Journals (Sweden)

Ahmed Z. A…fify

2014-12-01

Full Text Available This paper provides a new generalization of the complementary Weibull geometric distribution that introduced by Tojeiro et al. (2014, using the quadratic rank transmutation map studied by Shaw and Buckley (2007. The new distribution is referred to as transmuted complementary Weibull geometric distribution (TCWGD. The TCWG distribution includes as special cases the complementary Weibull geometric distribution (CWGD, complementary exponential geometric distribution(CEGD,Weibull distribution (WD and exponential distribution (ED. Various structural properties of the new distribution including moments, quantiles, moment generating function and RØnyi entropy of the subject distribution are derived. We proposed the method of maximum likelihood for estimating the model parameters and obtain the observed information matrix. A real data set are used to compare the ‡exibility of the transmuted version versus the complementary Weibull geometric distribution.

A study on transmutation of LLFPs using various types of HTGRs

Energy Technology Data Exchange (ETDEWEB)

Kora, Kazuki, E-mail: kora_k@nucl.kyushu-u.ac.jp [Department of Applied Quantum Physics and Nuclear Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka-shi, Fukuoka-ken (Japan); Nakaya, Hiroyuki; Matsuura, Hideaki [Department of Applied Quantum Physics and Nuclear Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka-shi, Fukuoka-ken (Japan); Goto, Minoru; Nakagawa, Shigeaki; Shimakawa, Satoshi [Japan Atomic Energy Agency, 4002 Narita-cho, Oarai-machi, Higashiibaraki-gun, Ibaraki, Ibaraki-ken (Japan)

2016-04-15

Highlights: • We propose utilization of a variety of HTGRs for LLFP transmutation and storage. • The transmutation performance of four types of HTGRs was examined and compared. • Some types of HTGRs show preferable characteristics for LLFP transmutation. - Abstract: In order to investigate the potential of high temperature gas-cooled reactors (HTGRs) for transmutation of long-lived fission products (LLFPs), numerical simulation of four types of HTGRs were carried out. In addition to the gas-turbine high temperature reactor system “GTHTR300”, which is the subject of our previous research, a small modular HTGR plant “HTR50S” and two types of plutonium burner HTGRs “Clean Burn with MA” and “Clean Burn without MA” were considered. The simulation results show that an early realization of LLFP transmutation using a compact HTGR may be possible since the HTR50S can transmute fair amount of LLFPs for its thermal output. The Clean Burn with MA can transmute a limited amount of LLFPs. However, an efficient LLFP transmutation using the Clean Burn without MA seems to be convincing as it is able to achieve very high burn-ups and produce LLFP transmutation more than GTHTR300. Based on these results, we propose utilization of variety of HTGRs for LLFP transmutation and storage.

The transmutation of americium: the Ecrix experiments in Phenix; Transmutation de l'americium: les experiences ecrix dans Phenix

Energy Technology Data Exchange (ETDEWEB)

Garnier, J C; Schmidt, N [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SESC), 13 - Saint-Paul-lez-Durance (France); Croixmarie, Y; Ottaviani, J P [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SPUA), 13 - Saint-Paul-lez-Durance (France); Varaine, F; Saint Jean, C de [CEA Cadarache, Dept. d' Etudes des Reacteurs (DER/SPRC), 13 - Saint-Paul-lez-Durance (France)

1999-07-01

The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be {sup 11}B{sub 4}C and CaH{sub 2} for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO{sub X} pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

The Transmuted Generalized Inverse Weibull Distribution

Directory of Open Access Journals (Sweden)

Faton Merovci

2014-05-01

Full Text Available A generalization of the generalized inverse Weibull distribution the so-called transmuted generalized inverse Weibull distribution is proposed and studied. We will use the quadratic rank transmutation map (QRTM in order to generate a flexible family of probability distributions taking the generalized inverseWeibull distribution as the base value distribution by introducing a new parameter that would offer more distributional flexibility. Various structural properties including explicit expressions for the moments, quantiles, and moment generating function of the new distribution are derived. We propose the method of maximum likelihood for estimating the model parameters and obtain the observed information matrix. A real data set are used to compare the flexibility of the transmuted version versus the generalized inverse Weibull distribution.

Transmutation of nuclear waste in nuclear reactors

International Nuclear Information System (INIS)

Abrahams, K.; Kloosterman, J.L.; Pilate, S.; Wehmann, U.K.

1996-03-01

The objective of this joint study of ECN, Belgonucleaire, and Siemens is to investigate possibilities for transmutation of nuclear waste in regular nuclear reactors or in special transmutation devices. Studies of possibilities included the limits and technological development steps which would be needed. Burning plutonium in fast reactors, gas-cooled high-temperature reactors and light water reactors (LWR) have been considered. For minor actinides the transmutation rate mainly depends on the content of the minor actinides in the reactor and to a much less degree on the fact whether one uses a homogeneous system (with the actinides mixed into the fuel) or a heterogeneous system. If one wishes to stabilise the amount of actinides from the present LWRs, about 20% of all nuclear power would have to be generated in special burner reactors. It turned out that reactor transmutation of fission products would require considerable recycling efforts and that the time needed for a substantial transmutation would be rather long for the presently available levels of the neutron flux. If one would like to design burner systems which can serve more light water reactors, a large effort would be needed and other burners (possibly driven by accelerators) should be considered. (orig.)

Safety characteristics of potential waste transmutation systems

International Nuclear Information System (INIS)

Van Tuyle, G.J.

1993-01-01

For nuclear waste transmutation to alter significantly the need for geologic disposal of spent fuel from US Light-water reactors (LWRs), about 1.4% of the spent fuel (by mass) must be separated and transmuted. This includes the plutonium, the minor actinides, and four fission products: iodine. technetium, cesium and strontium. Regarding the actinides, fissioning of the plutonium, neptunium, americium, and curium generates a great deal of heat, so much so that most of the plutonium should be used to produce power. However, these actinides have some undesirable neutronic characteristics, and their utilization in reactors or subcritical (proton-accelerator) targets requires either a fast neutronic spectrum or a very high thermal-neutron flux. Transmutation of the fission products is generally by neutron capture, although this is difficult in the case of cesium and strontium. In this paper, various proposed means of transmuting the actinides and fission products are discussed, with the main focus being on the safety characteristics of each approach

Separation of actinides and their transmutation

International Nuclear Information System (INIS)

Bouchard, M.; Bathelier, M.; Cousin, M.

1978-08-01

Neutron irradiation of long-half-life actinides for transmutation into elements with shorter half-life is investigated as a means to reduce the long-term hazards of these actinides. The effectiveness of the method is analysed by applying it to fission product solutions from the first extraction cycle of fuel reprocessing plants. Basic principles, separation techniques and transmutation efficiencies are studied and discussed in detail

Performance of a transmutation advanced device for sustainable energy application

International Nuclear Information System (INIS)

Garcia, C.; Rosales, J.; Garcia, L.; Perez-Navarro, A.; Escriva, A.; Abanades, A.

2009-01-01

Preliminary studies have been performed to design a device for nuclear waste transmutation and hydrogen generation based on a gas cooled pebble bed accelerator driven system, TADSEA (transmutation advanced device for sustainable energy application). In previous studies we have addressed the viability of an ADS Transmutation device that uses as fuel wastes from the existing LWR power plants, encapsulated in graphite in the form of pebble beds, being cooled by helium which enables high temperatures, in the order of 1200 K, to facilitate hydrogen generation from water either by high temperature electrolysis or by thermo chemical cycles. To design this device several configurations were studied, including several reactors thickness, to achieve the desired parameters, the transmutation of nuclear waste and the production of 100 MW. of thermal power. In this paper we are presenting new studies performed on deep burn in-core fuel management strategy for LWR waste. We analyze the fuel cycle on TADSEA device based on driver and transmutation fuel that were proposed for the General Atomic design of a gas turbine-modular helium reactor. We compare the transmutation results of the three fuel management strategies, using driven and transmutation, and standard LWR spend fuel, and present several parameters that describe the neutron performance of TADSEA nuclear core as the fuel and moderator temperature reactivity coefficients and transmutation chain. (author)

Performance of a transmutation advanced device for sustainable energy application

Energy Technology Data Exchange (ETDEWEB)

Garcia, C.; Rosales, J.; Garcia, L. [Instituto Superior de Tecnologias y Ciencias Aplicadas (INSTEC), La Habana (Cuba); Perez-Navarro, A.; Escriva, A. [Universidad Politecnica de Valencia, Valencia (Spain). Inst. de Ingenieria Energetica; Abanades, A. [Universidad Politecnica de Madrid (Spain). Grupo de Modelizacion de Sistemas Termoenergeticos

2009-07-01

Preliminary studies have been performed to design a device for nuclear waste transmutation and hydrogen generation based on a gas cooled pebble bed accelerator driven system, TADSEA (transmutation advanced device for sustainable energy application). In previous studies we have addressed the viability of an ADS Transmutation device that uses as fuel wastes from the existing LWR power plants, encapsulated in graphite in the form of pebble beds, being cooled by helium which enables high temperatures, in the order of 1200 K, to facilitate hydrogen generation from water either by high temperature electrolysis or by thermo chemical cycles. To design this device several configurations were studied, including several reactors thickness, to achieve the desired parameters, the transmutation of nuclear waste and the production of 100 MW. of thermal power. In this paper we are presenting new studies performed on deep burn in-core fuel management strategy for LWR waste. We analyze the fuel cycle on TADSEA device based on driver and transmutation fuel that were proposed for the General Atomic design of a gas turbine-modular helium reactor. We compare the transmutation results of the three fuel management strategies, using driven and transmutation, and standard LWR spend fuel, and present several parameters that describe the neutron performance of TADSEA nuclear core as the fuel and moderator temperature reactivity coefficients and transmutation chain. (author)

Critique of rationale for transmutation of nuclear waste

International Nuclear Information System (INIS)

Smith, C.F.; Cohen, J.J.

1980-07-01

It has been suggested that nuclear transmutation could be used in the elimination or reduction of hazards from radioactive wastes. The rationale for this suggestion is the subject of this paper. The objectives of partitioning-transmutation are described. The benefits are evaluated. The author concludes that transmutation would appear at best to offer the opportunity of reducing an already low risk. This would not seem to be justifiable considering the cost. If non-radiological risks are considered, there is a negative total benefit

Comparative analysis of sub-critical transmutation reactor concepts

International Nuclear Information System (INIS)

Chang, S. H.

1997-01-01

The long-lived nuclear wastes have been substantially generated from the light water reactor for a few decades. The toxicity of these spent fuels will be higher than that of the uranium ore, even if those will be stored in the repository more than ten thousands. Hence the means of transmuting the key long-lived nuclear wastes, primarily the minor actinides, using a hybrid proton accelerator and subcritical transmutation reactor, are proposed. Until now, the representative concepts for a subcritical transmutation reactor are the Energy Amplifier, the OMEGA project, the ATW and the MSBR. The detailed concepts and the specifications are illustrated in Table 1. The design requirements for the subcritical transmutation reactor are the high transmutation rate of long-lived nuclear wastes, safety and economics. And to propose the subcritical transmutation reactor concepts, the coolant, the target material and fuel type are carefully considered. In these aspects, the representative concepts for a subcritical transmutation reactor in Table 1 have been surveyed. The requirements for a target and a coolant are the reliable, low maintenance operation and safe operation to minimize the wastes. The reliable, low maintenance operation and safe operation to minimize the wastes. The reliable coolant must have the low melting point, high heat capacity and excellent physical properties. And the target material must have high neutron yield for a given proton condition and easy heat removal capability. Therefore in respect with the above requirements, Pb-Bi is proposed as the coolant and the target material for the subcritical reactor. Because the neutron yield for a given proton energy increases linearly with mass number up to bismuth but in heavier elements spallation events sharply increase both the neutron and heat outputs, Pb-Bi meets not only such the requirements as the above for the coolant but also those for the coolant and target, the simplification of system can be achieved

Neutron Transmutation Doping of Silicon at Research Reactors

International Nuclear Information System (INIS)

2012-05-01

This publication details the processes and history of neutron transmutation doping of silicon, particularly its commercial pathway, followed by the requirements for a technologically modern and economically viable production scheme and the current trends in the global market for semiconductor products. It should serve as guidelines on the technical requirements, involved processes and required quality standards for the transmission of sound practices and advice for research reactor managers and operators planning commercial scale production of silicon. Furthermore, a detailed and specific database of most of the world's research reactor facilities in this domain is included, featuring their characteristics for irradiation capabilities, associated production capacities and processing.

The Physics of transmutation systems : system capabilities and performances

International Nuclear Information System (INIS)

Finck, P. J.

2002-01-01

This document is complementary to a document produced by Prof. Salvatores on ''The Physics of Transmutation in Critical or Subcritical Reactors and the Impact on the Fuel Cycle''. In that document, Salvatores describes the fundamental of transmutation, through basic physics properties and general parametric studies. In the present document we try to go one step further towards practical implementation (while recognizing that the practical issues such as technology development and demonstration, and economics, can only be mentioned in a very superficial manner). Section 1 briefly overviews the possible objectives of transmutation systems, and links these different objectives to possible technological paths. It also describes the overall constraints which have to be considered when developing and implementing transmutation systems. In section 2 we briefly overview the technological constraints which need to be accounted for when designing transmutation systems. In section 3 we attempt to provide a simplified classification of transmutation systems in order to clarify later comparisons. It compares heterogeneous and homogeneous recycle strategies, and single and multi-tier systems. Section 4 presents case analyses for assessing the transmutation performance of various individual systems, starting with LWR's ((1) generic results; (2) multirecycle of plutonium; (3) an alternative: transmutation based on a Thorium fuel cycle), followed by Gas-Cooled Reactors (with an emphasis on the ''deep burn'' approach), and followed by Fast Reactors and Accelerator Driven systems ((1) generic results; (2) homogeneous recycle of transuranics; (3) practical limit between Fast Reactors and Accelerator Driven Systems) Section 5 summarizes recent results on integrated system performances. It focuses first on interface effects between the two elements of a dual tier system, and then summarizes the major lessons learned from recent global physics studies

HLW disposal by fission reactors; calculation of trans-mutation rate and recycle

International Nuclear Information System (INIS)

Mulyanto

1997-01-01

Transmutation of MA (Minor actinide) and LLFPS (long-lived fission products) into stable nuclide or short-lived isotopes by fission reactors seem to become an alternative technology for HLW disposal. in this study, transmutation rate and recycle calculation were developed in order to evaluate transmutation characteristics of MA and LLFPs in the fission reactors. inventory of MA and LLFPs in the transmutation reactors were determined by solving of criticality equation with 1-D cylindrical geometry of multigroup diffusion equations at the beginning of cycle (BOC). transmutation rate and burn-up was determined by solving of depletion equation. inventory of MA and LLFPs was calculated for 40 years recycle. From this study, it was concluded that characteristics of MA and LLFPs in the transmutation reactors can be evaluated by recycle calculation. by calculation of transmutation rate, performance of fission reactor for transmutation of MA or LLFPs can be discussed

Development of transmutation technologies of radioactive waste by actinoid hydride

International Nuclear Information System (INIS)

Konashi, Kenji; Matsui, Hideki; Yamawaki, Michio

2001-01-01

Two waste treatment methods, geological disposal and transmutation, have been studied. The transmutation method changes long-lived radioactive nuclides to short-lived one or stabilizes them by nuclear transformation. The transmutation by actinoid hydride is exactly alike that transformation method from actinoid disposal waste to Pu fuel. For this object, OMEGA project is processing now. The transmutation is difficult by two causes such as large amount of long-lived radioactive nuclides and not enough development of control technologies of nuclear reaction except atomic reactor. The transmutation using actinoid hydride has merits that the amount of actinoid charged in the target increases and the effect of thermal neutrons on fuel decreases depending on homogeneous transmutation velocity in the target. Development of stable actinoid hydride under the conditions of reactor temperature and irradiation environment is important. The experimental results of U-ZrH 1.6 are shown in this paper. The irradiation experiment using Th hydride has been proceeding. (S.Y.)

Study on neutron spectrum for effective transmutation of minor actinides in thermal reactors

International Nuclear Information System (INIS)

Takeda, Toshikazu; Yokoyama, Kenji

1997-01-01

The transmutation of minor actinides (MAs) has been investigated in thermal reactor cells using mixed oxide fuel with MAs. The effect of neutron spectra on transmutation is studied by changing the neutron spectra. Five transmutation rates are compared: direct fission incineration rate, capture transmutation rate, consumption rate, overall fission incineration rate and inventory difference transmutation rate. The relations between these transmutation rates and their dependence on the neutron spectrum were investigated. To effectively incinerate MAs it is necessary to maximize the overall fission incineration rate and the inventory difference transmutation rate. These transmutation rates become maximum when the fraction of neutrons below 1 eV is about 8% for the case where the MA addition is 1-3%. When the MA addition is over 5%, the transmutation rates become maximum for very hard neutron spectrum. (Author)

Heterogeneous fuels for minor actinides transmutation: Fuel performance codes predictions in the EFIT case study

Energy Technology Data Exchange (ETDEWEB)

Calabrese, R., E-mail: rolando.calabrese@enea.i [ENEA, Innovative Nuclear Reactors and Fuel Cycle Closure Division, via Martiri di Monte Sole 4, 40129 Bologna (Italy); Vettraino, F.; Artioli, C. [ENEA, Innovative Nuclear Reactors and Fuel Cycle Closure Division, via Martiri di Monte Sole 4, 40129 Bologna (Italy); Sobolev, V. [SCK.CEN, Belgian Nuclear Research Centre, Boeretang 200, B-2400 Mol (Belgium); Thetford, R. [Serco Technical and Assurance Services, 150 Harwell Business Centre, Didcot OX11 0QB (United Kingdom)

2010-06-15

Plutonium recycling in new-generation fast reactors coupled with minor actinides (MA) transmutation in dedicated nuclear systems could achieve a decrease of nuclear waste long-term radiotoxicity by two orders of magnitude in comparison with current once-through strategy. In a double-strata scenario, purpose-built accelerator-driven systems (ADS) could transmute minor actinides. The innovative nuclear fuel conceived for such systems demands significant R and D efforts in order to meet the safety and technical performance of current fuel systems. The Integrated Project EUROTRANS (EUROpean research programme for the TRANSmutation of high level nuclear waste in ADS), part of the EURATOM Framework Programme 6 (FP6), undertook some of this research. EUROTRANS developed from the FP5 research programmes on ADS (PDS-XADS) and on fuels dedicated to MA transmutation (FUTURE, CONFIRM). One of its main objectives is the conceptual design of a small sub-critical nuclear system loaded with uranium-free fuel to provide high MA transmutation efficiency. These principles guided the design of EFIT (European Facility for Industrial Transmutation) in the domain DESIGN of IP EUROTRANS. The domain AFTRA (Advanced Fuels for TRAnsmutation system) identified two composite fuel systems: a ceramic-ceramic (CERCER) where fuel particles are dispersed in a magnesia matrix, and a ceramic-metallic (CERMET) with a molybdenum matrix in the place of MgO matrix to host a ceramic fissile phase. The EFIT fuel is composed of plutonium and MA oxides in solid solution with isotopic vectors typical of LWR spent fuel with 45 MWd/kg{sub HM} discharge burnup and 30 years interim storage before reprocessing. This paper is focused on the thermomechanical state of the hottest fuel pins of two EFIT cores of 400 MW{sub (th)} loaded with either CERCER or CERMET fuels. For calculations three fuel performance codes were used: FEMALE, TRAFIC and TRANSURANUS. The analysis was performed at the beginning of fuel life

Transmutation of fission products with the use of an accelarator

International Nuclear Information System (INIS)

Kase, T.; Harada, H.; Takahashi, T.

1995-01-01

The three transmutation methods with the use of an accelerator, the proton method, the spallation neutron method and the μCF method, are employed for the transmutation of long-lived nuclides in high level radioactive wastes. The transmutation energies and the effective half-lives of 99 Tc and 137 Cs for these transmutation methods are calculated by the Monte Carlo simulation codes for particle transport. The transmutation energies of the proton method are larger than those of the spallation neutron method and the μCF method under the condition of the same effective half life. The proton method is difficult to meet energy balance criterion. On the other hand, the spallation neutron method and the μCF method have possibility to meet the energy balance criterion. (author)

Enhancing TRU burning and Am transmutation in Advanced Recycling Reactor

International Nuclear Information System (INIS)

Ikeda, Kazumi; Kochendarfer, Richard A.; Moriwaki, Hiroyuki; Kunishima, Shigeru

2011-01-01

Research highlights: → This ARR is an oxide fueled sodium cooled reactor based on innovative technologies to destruct TRU. → TRU burning core is designed to burn TRU at 28 kg/TW th h, adding moderator pins of B 4 C (Enriched B-11). → Am transmutation core can transmute Am at 34 kg/TW th h, adding uranium free AmN blanket to TRU burning core. → The TRU burning core improves TRU burning by 40-50% than the previous core. → The Am transmutation core can transmute Am effectively, keeping the void reactivity acceptable. - Abstract: This paper presents about conceptual designs of Advanced Recycling Reactor (ARR) focusing on enhancement in transuranics (TRU) burning and americium (Am) transmutation. The design has been conducted in the context of the Global Nuclear Energy Partnership (GNEP) seeking to close nuclear fuel cycle in ways that reduce proliferation risks, reduce the nuclear waste in the US and further improve global energy security. This study strives to enhance the TRU burning and the Am transmutation, assuming the development of related technologies in this study, while the ARR based on mature technologies was designed in the previous study. It has followed that the provided TRU burning core is designed to burn TRU at 28 kg/TW th h, by adding moderator pins of B 4 C (Enriched B-11) and the Am transmutation core will be able to transmute Am at 34 kg/TW th h, by locating Am blanket of AmN around the TRU burning core. It indicates that these concepts improve TRU burning by 40-50% than the previous core and can transmute Am effectively, keeping the void reactivity acceptable.

The transmutation of americium: the Ecrix experiments in Phenix; Transmutation de l'americium: les experiences ecrix dans Phenix

Energy Technology Data Exchange (ETDEWEB)

Garnier, J.C.; Schmidt, N. [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SESC), 13 - Saint-Paul-lez-Durance (France); Croixmarie, Y.; Ottaviani, J.P. [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SPUA), 13 - Saint-Paul-lez-Durance (France); Varaine, F.; Saint Jean, C. de [CEA Cadarache, Dept. d' Etudes des Reacteurs (DER/SPRC), 13 - Saint-Paul-lez-Durance (France)

1999-07-01

The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be {sup 11}B{sub 4}C and CaH{sub 2} for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO{sub X} pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

The Beta Transmuted Weibull Distribution

Directory of Open Access Journals (Sweden)

Manisha Pal

2014-06-01

Full Text Available The paper introduces a beta transmuted Weibull distribution, which contains a number ofdistributions as special cases. The properties of the distribution are discussed and explicit expressions are derived for the mean deviations, Bonferroni and Lorenz curves, and reliability. The distribution and moments of order statistics are also studied. Estimation of the model parameters by the method of maximum likelihood is discussed. The log beta transmuted Weibull model is introduced to analyze censored data. Finally, the usefulness of the new distribution in analyzing positive data is illustrated.

Dual neutral particle induced transmutation in CINDER2008

Energy Technology Data Exchange (ETDEWEB)

Martin, W.J., E-mail: wjmarti@sandia.gov [Sandia National Laboratories, Albuquerque, NM 87185 (United States); University of New Mexico, Albuquerque, NM 87131 (United States); Oliveira, C.R.E. de; Hecht, A.A. [University of New Mexico, Albuquerque, NM 87131 (United States)

2014-12-11

Although nuclear transmutation methods for fission have existed for decades, the focus has been on neutron-induced reactions. Recent novel concepts have sought to use both neutrons and photons for purposes such as active interrogation of cargo to detect the smuggling of highly enriched uranium, a concept that would require modeling the transmutation caused by both incident particles. As photonuclear transmutation has yet to be modeled alongside neutron-induced transmutation in a production code, new methods need to be developed. The CINDER2008 nuclear transmutation code from Los Alamos National Laboratory is extended from neutron applications to dual neutral particle applications, allowing both neutron- and photon-induced reactions for this modeling with a focus on fission. Following standard reaction modeling, the induced fission reaction is understood as a two-part reaction, with an entrance channel to the excited compound nucleus, and an exit channel from the excited compound nucleus to the fission fragmentation. Because photofission yield data—the exit channel from the compound nucleus—are sparse, neutron fission yield data are used in this work. With a different compound nucleus and excitation, the translation to the excited compound state is modified, as appropriate. A verification and validation of these methods and data has been performed. This has shown that the translation of neutron-induced fission product yield sets, and their use in photonuclear applications, is appropriate, and that the code has been extended correctly. - Highlights: • The CINDER2008 transmutation code was modified to include photon-induced transmutation tracking. • A photonuclear interaction library was created to allow CINDER2008 to track photonuclear interactions. • Photofission product yield data sets were created using fission physics similarities with neutron-induced fission.

Actinide Partitioning and Transmutation Program. Progress report, April 1--June 30, 1977

Energy Technology Data Exchange (ETDEWEB)

Tedder, D. W.; Blomeke, J. O. [comps.

1977-10-01

Experimental work on the 16 tasks comprising the Actinide Partitioning and Transmutation Program was continued. Summaries of work are given on Purex Process modifications, actinide recovery, Am-Cm recovery, radiation effects on ion exchangers, LMFBR transmutation studies, thermal reactor transmutation studies, fuel cycle studies, and partitioning-transmutation evaluation. (JRD)

Fast reactor core concepts to improve transmutation efficiency

International Nuclear Information System (INIS)

Fujimura, Koji; Kawashima, Katsuyuki; Itooka, Satoshi

2015-01-01

Fast Reactor (FR) core concepts to improve transmutation efficiency were conducted. A heterogeneous MA loaded core was designed based on the 1000MWe-ABR breakeven core. The heterogeneous MA loaded core with Zr-H loaded moderated targets had a better transmutation performance than the MA homogeneous loaded core. The annular pellet rod design was proposed as one of the possible design options for the MA target. It was shown that using annular pellet MA rods mitigates the self-shielding effect in the moderated target so as to enhance the transmutation rate

Accelerator-driven transmutation of spent fuel elements

Science.gov (United States)

Venneri, Francesco; Williamson, Mark A.; Li, Ning

2002-01-01

An apparatus and method is described for transmuting higher actinides, plutonium and selected fission products in a liquid-fuel subcritical assembly. Uranium may also be enriched, thereby providing new fuel for use in conventional nuclear power plants. An accelerator provides the additional neutrons required to perform the processes. The size of the accelerator needed to complete fuel cycle closure depends on the neutron efficiency of the supported reactors and on the neutron spectrum of the actinide transmutation apparatus. Treatment of spent fuel from light water reactors (LWRs) using uranium-based fuel will require the largest accelerator power, whereas neutron-efficient high temperature gas reactors (HTGRs) or CANDU reactors will require the smallest accelerator power, especially if thorium is introduced into the newly generated fuel according to the teachings of the present invention. Fast spectrum actinide transmutation apparatus (based on liquid-metal fuel) will take full advantage of the accelerator-produced source neutrons and provide maximum utilization of the actinide-generated fission neutrons. However, near-thermal transmutation apparatus will require lower standing

MA-burners efficiency parameters allowing for the duration of transmutation process

International Nuclear Information System (INIS)

Gulevich, A.; Zemskov, E.; Kalugin, A.; Ponomarev, L.; Seliverstov, V.; Seregin, M.

2010-01-01

Transmutation of minor actinides (MA) means their transforming into the fission products. Usually, MA-burner's transmutation efficiency is characterized by the static parameters only, such as the number of neutrons absorbed and the rate of MA feeding. However, the proper characterization of MA-burner's efficiency additionally requires the consideration of parameters allowing for the duration of the MA transmutation process. Two parameters of that kind are proposed: a) transmutation time τ - mean time period from the moment a mass of MA is loaded into the burner's fuel cycle to be transmuted to the moment this mass is completely transmuted; b) number of reprocessing cycles n rep - effective number of reprocessing cycles a mass of loaded MA has to undergo before being completely transmuted. Some of MA-burners' types have been analyzed from the point of view of these parameters. It turned out that all of them have the value of parameters too high from the practical point of view. It appears that some new approaches to MA-burner's design have to be used to significantly reduce the value of these parameters in order to make the large-scale MA transmutation process practically reasonable. Some of such approaches are proposed and their potential efficiency is discussed. (authors)

Analysis of advanced European nuclear fuel cycle scenarios including transmutation and economic estimates

International Nuclear Information System (INIS)

Rodríguez, Iván Merino; Álvarez-Velarde, Francisco; Martín-Fuertes, Francisco

2014-01-01

scenarios and breakdown of LCOE contributors rather than provision of absolute values, as technological readiness levels are low for most of the advanced fuel cycle stages. The obtained estimations show an increase of LCOE – averaged over the whole period – with respect to the reference open cycle scenario of 20% for Pu management scenario and around 35% for both transmutation scenarios. The main contribution to LCOE is the capital costs of new facilities, quantified between 60% and 69% depending on the scenario. An uncertainty analysis is provided around assumed low and high values of processes and technologies

Oxide fuels and targets for transmutation

International Nuclear Information System (INIS)

Sudreau, F.; Bonnerot, J.M.; Warin, D.; Gaillard-Groleas, G.; Ferroud-Plattet, M.P.

2007-01-01

Full text of publication follows. Direction 1 of the French Act dated 30 December 1991 on the management of high-level, long-lived radioactive waste involves exploring solutions designed to separate long-lived radionuclides from the spent fuel and to transmute them under neutron flux into shorter half-lives or stable elements. In the French research programme conducted by CEA, these radionuclides are mainly minor actinides (americium, neptunium and curium) and fission products (particularly caesium, iodine and technetium). Within this context, this paper aims at illustrating the vast programme that CEA has performed in order to demonstrate the scientific and technical feasibility of minor actinide transmutation. An important part of the research was carried out in collaboration with French research (CNRS) and industrial (EDF, AREVA) organisations, and also in the framework of international co-operation programmes with the European Institute for Transuranium Elements in Karlsruhe (ITU), the US Department of Energy (DOE), the Japanese Atomic Energy Research Institute (now JAEA) and Central Research Institute of Electric Power Industry (CRIEPI) and the Russian Ministry for Atomic Energy (ROSATOM). Such research made it possible to evaluate the capacity of MOX fuels to be used as a support for minor actinide transmutation (homogeneous method). Simulations of pressurised water reactor (PWR) fuels have revealed the limits of this transmutation method, which are mainly related to the pressurization of the fuel rods and the formation of high active californium. On the contrary, for sodium-cooled fast reactor fuels possibly designed with large expansion plenums a first experimental demonstration of the transmutation of americium and neptunium has been successful in the Phenix reactor. Various studies designed to demonstrate the theoretical and experimental feasibility of transmutation using an inert support (heterogeneous method) have been carried out in HFR (EFTTRA

Development of nuclear transmutation technology - A study on accelerator-driven transmutation of long-lived radionuclide

Energy Technology Data Exchange (ETDEWEB)

Chung, Chang Hyun; Chung, Kie Hyung; Hong, Sang Hee; Hwang, Il Soon; Park, Byung Gi; Yang, Hyung Lyeol; Kim, Duk Kyu; Huh, Chang Wook [Seoul National University, Seoul (Korea, Republic of)

1996-07-01

The objective of this study is to help establish the long-range nuclear waste disposal strategy through the investigations and comparisons of various= concepts of the accelerator-driven nuclear waste transmutation reactors, which have been suggested to replace the geological waste disposal due to the technical uncertainties in the long-time scale. Nuclear data, categorized in high -and low-energy neutron cross-sections, were investigated and the structures, principles, and recent progresses of proton linac were reviews, Also the accelerator power for transmutation and the economics were referred, The comparison of the transmutation concepts concentrated on two: Japanese OMEGA program of alloy fuelled system, Minor actinide molten salt system, and Eutectic alloy system and American ATW program of aqueous system and molten salt system. From the comparative study, a state-of-art of the technology has been identified as a concept employing proton-accelerate of 800 {approx} 1600 MeV with 100 mA capacity combined with liquid lead target, molten salt blanket and on-line chemical separation using centrifuge and electrowinning technology. 34 refs., 25 tabs., 64 figs. (author)

Neutronics analysis of minor actinides transmutation in a fusion-driven subcritical system

International Nuclear Information System (INIS)

Yang, Chao; Cao, Liangzhi; Wu, Hongchun; Zheng, Youqi; Zu, Tiejun

2013-01-01

Highlights: • A fusion fission hybrid system for MA transmutation is proposed. • The analysis of neutronics effects on the transmutation is performed. • The transmutation rate of MA reaches 86.5% by 25 times of recycling. -- Abstract: The minor actinides (MAs) transmutation in a fusion-driven subcritical system is analyzed in this paper. The subcritical reactor is driven by a tokamak D-T fusion device with relatively easily achieved plasma parameters and tokamak technologies. The MAs discharged from the light water reactor (LWR) are loaded in transmutation zone. Sodium is used as the coolant. The mass percentage of the reprocessed plutonium (Pu) in the fuel is raised from 0 to 48% and stepped by 12% to determine its effect on the MAs transmutation. The lesser the Pu is loaded, the larger the MAs transmutation rate is, but the smaller the energy multiplication factor is. The neutronics analysis of two loading patterns is performed and compared. The loading pattern where the mass percentage of Pu in two regions is 15% and 32.9% respectively is conducive to the improvement of the transmutation fraction within the limits of burn-up. The final transmutation fraction of MAs can reach 17.8% after five years of irradiation. The multiple recycling is investigated. The transmutation fraction of MAs can reach about 61.8% after six times of recycling, and goes up to about 86.5% after 25

A Study on the Kinetic Characteristics of Transmutation Process Reactor

Energy Technology Data Exchange (ETDEWEB)

Chung, Chang Hyun; You, Young Woo; Cho, Jae seon; Huh, Chang Wook; Kim, Doh Hyung [Seoul National University, Seoul (Korea, Republic of)

1997-07-01

The purpose of this study is to examine the transient heat transfer characteristics of liquid mental as the coolant used in accelerator-driven transmutation process reactor which is related the disposal of high-level radioactive nuclide. At current stage, the accelerator-driven transmutation process is investigated as the most appropriate method among many transmutation process methods. In this study, previous research works are investigated especially about the thermal hydraulics and kinetic behavior of coolant material including heat transfer of coolant in transmutation process reactor. A study on the heat transfer characteristics of liquid metal is performed based on the thermal hydraulic kinetic characteristics of liquid metal reactor which uses liquid metal coolant. Based on this study, the most appropriate material for the coolant of transmutation reactor will be recommended. 53 refs., 15 tabs., 33 figs. (author)

Tokamak transmutation of (nuclear) waste (TTW): Parametric studies

International Nuclear Information System (INIS)

Cheng, E.T.; Krakowski, R.A.; Peng, Y.K.M.

1994-01-01

Radioactive waste generated as part of the commercial-power and defense nuclear programs can be either stored or transmuted. The latter treatment requires a capital-intensive neutron source and is reserved for particularly hazardous and long-lived actinide and fission-product waste. A comparative description of fusion-based transmutation is made on the basis of rudimentary estimates of ergonic performance and transmutation capacities versus inventories for both ultra-low-aspect-ratio (spherical torus, ST) and conversional (aspect-ratio) tokamak fusion-power-core drivers. The parametric systems studies reported herein provides a preamble to more-detailed, cost-based systems analyses

MA-burners efficiency parameters allowing for the duration of transmutation process

Energy Technology Data Exchange (ETDEWEB)

Gulevich, A.; Zemskov, E. [Institute of Physics and Power Engineering, Bondarenko Square 1, Obninsk, Kaluga Region 249020 (Russian Federation); Kalugin, A.; Ponomarev, L. [Russian Research Center ' ' Kurchatov Institute' ' Kurchatov Square 1, Moscow 123182 (Russian Federation); Seliverstov, V. [Institute of Theoretical and Experimental Physics ul.B. Cheremushkinskaya 25, Moscow 117259 (Russian Federation); Seregin, M. [Russian Research Institute of Chemical Technology Kashirskoe Shosse 33, Moscow 115230 (Russian Federation)

2010-07-01

Transmutation of minor actinides (MA) means their transforming into the fission products. Usually, MA-burner's transmutation efficiency is characterized by the static parameters only, such as the number of neutrons absorbed and the rate of MA feeding. However, the proper characterization of MA-burner's efficiency additionally requires the consideration of parameters allowing for the duration of the MA transmutation process. Two parameters of that kind are proposed: a) transmutation time {tau} - mean time period from the moment a mass of MA is loaded into the burner's fuel cycle to be transmuted to the moment this mass is completely transmuted; b) number of reprocessing cycles n{sub rep} - effective number of reprocessing cycles a mass of loaded MA has to undergo before being completely transmuted. Some of MA-burners' types have been analyzed from the point of view of these parameters. It turned out that all of them have the value of parameters too high from the practical point of view. It appears that some new approaches to MA-burner's design have to be used to significantly reduce the value of these parameters in order to make the large-scale MA transmutation process practically reasonable. Some of such approaches are proposed and their potential efficiency is discussed. (authors)

Neutron data experiments for transmutation. Annual Report 2007/2008

Energy Technology Data Exchange (ETDEWEB)

Blomgren, J.; al-Adili, A.; Andersson, P.; Bevilacqua, R.; Nilsson, L.; Pomp, S.; Simutkin, V.; Oehrn, A.; Oesterlund, M. (Uppsala Univ. (Sweden). Div. of Applied Nuclear Physics)

2008-08-15

The project NEXT, Neutron data Experiments for Transmutation, is performed within the nuclear reactions group of the Dept. of Physics and Astronomy. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group is operating two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: - The SCANDAL facility has been upgraded. - One PhD student has successfully defended her thesis. - Two PhD students have been accepted. - Vasily Simutkin has been selected as one of the top 12 PhD students within the European Nuclear Education Network. He has accordingly been invited to present his work at the ENEN PhD event held in connection with the PHYSOR conference in Interlaken, Switzerland, September 2008. - A research collaboration with the dedicated EU laboratory for nuclear data research has been established. - A well-attended workshop on nuclear data for ADS and Gen-IV has been organized as part of the EU project CANDIDE (Coordination Action on Nuclear Data for Industrial Development in Europe), coordinated by Jan Blomgren. - Several experiments have been performed at TSL, with beamtime funded through the EU project EFNUDAT (European Facilities for Nuclear Data research), partly coordinated by Jan Blomgren. - Nuclear power education has reached all-time high at Uppsala University. In particular, industry education has increased significantly. - IAEA has visited Uppsala University to investigate the industry-related nuclear power education, as part of a safety culture review of the Forsmark nuclear power plant

Neutron data experiments for transmutation. Annual Report 2007/2008

International Nuclear Information System (INIS)

Blomgren, J.; Al-Adili, A.; Andersson, P.; Bevilacqua, R.; Nilsson, L.; Pomp, S.; Simutkin, V.; Oehrn, A.; Oesterlund, M.

2008-08-01

The project NEXT, Neutron data Experiments for Transmutation, is performed within the nuclear reactions group of the Dept. of Physics and Astronomy. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group is operating two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: - The SCANDAL facility has been upgraded. - One PhD student has successfully defended her thesis. - Two PhD students have been accepted. - Vasily Simutkin has been selected as one of the top 12 PhD students within the European Nuclear Education Network. He has accordingly been invited to present his work at the ENEN PhD event held in connection with the PHYSOR conference in Interlaken, Switzerland, September 2008. - A research collaboration with the dedicated EU laboratory for nuclear data research has been established. - A well-attended workshop on nuclear data for ADS and Gen-IV has been organized as part of the EU project CANDIDE (Coordination Action on Nuclear Data for Industrial Development in Europe), coordinated by Jan Blomgren. - Several experiments have been performed at TSL, with beamtime funded through the EU project EFNUDAT (European Facilities for Nuclear Data research), partly coordinated by Jan Blomgren. - Nuclear power education has reached all-time high at Uppsala University. In particular, industry education has increased significantly. - IAEA has visited Uppsala University to investigate the industry-related nuclear power education, as part of a safety culture review of the Forsmark nuclear power plant

General solution of Bateman equations for nuclear transmutations

International Nuclear Information System (INIS)

Cetnar, Jerzy

2006-01-01

The paper concerns the linear chain method of solving Bateman equations for nuclear transmutation in derivation of the general solution for linear chain with repeated transitions and thus elimination of existing numerical problems. In addition, applications of derived equations for transmutation trajectory analysis method is presented

Contribution of the European Commission to a European Strategy for HLW Management through Partitioning and Transmutation: Presentation of MYRRHA and its Role in the European P and T Strategy

International Nuclear Information System (INIS)

Abderrahim, H.A.; Van den Eynde, G.; Baeten, P.; Schyns, M.; Vandeplassche, D.; Kochetkov, A.

2015-01-01

To be able to answer the world's increasing demand for energy, nuclear energy must be part of the energy mix. As a consequence of the nuclear electricity generation, high-level nuclear waste (HLW) is produced. The HLW is presently considered to be managed through its burying in geological storage. Partitioning and transmutation (P and T) has been pointed out as the strategy to reduce the radiological impact of HLW. Transmutation can be achieved in an efficient way in fast neutron spectrum facilities, both in critical fast reactors as well as in accelerator driven systems (ADSs). For more than two decades, the European Commission has been co-funding various research and development projects conducted in many European research organisations and industries related to P and T as a complementary strategy for high-level waste management to the geological disposal. In 2005, a European strategy for the implementation of P and T for a large part of the HLW in Europe indicated the need for the demonstration of its feasibility at an 'engineering' level. The R and D activities of this strategy were arranged in four 'building blocks': 1. Demonstration of the capability to process a sizable amount of spent fuel from commercial light water reactors (LWRs) in order to separate plutonium, uranium and minor actinides. 2. Demonstration of the capability to fabricate at a semi-industrial level the dedicated fuel needed as load in a dedicated transmuter. 3. Design and construction of one or more dedicated transmuters. 4. Provision of a specific installation for processing of the dedicated fuel unloaded from the transmuter, which can be of a different type than the one used to process the original spent fuel unloaded from the commercial power plants, together with the fabrication of new dedicated fuel. MYRRHA contributes to the third building block. MYRRHA is an ADS under development at SCK.CEN in collaboration with a large number of European partners. One of

Transmutation Scenarios Impacts on Advanced Nuclear Cycles. Fabrication, Reprocessing and Transportation

International Nuclear Information System (INIS)

Saturnin, A.; Sarrat, P.; Hancok, H.; Milot, J.-F.; Duret, B.; Jasserand, F.; Fillastre, E.; Giffard, F.-X.; Chabert, C.; Van Den Durpel, L.; Caron-Charles, M.; Lefevre, J.C.; Carlier, B.; Arslan, M.; Favet, D.; Garzenne, C.; Barbrault, P.

2013-01-01

Conclusions: First detailed assessment of plants and transportation in various transmutation scenarios. In case of curium transmutation: large difficulties and uncertainties requiring whole new technology development (more pronounced for ADS option). For Am transmutation: more feasible, still to be demonstrated on specific points for industrial extrapolation

Fuels and targets for incineration and transmutation of actinides: the ITU programme

International Nuclear Information System (INIS)

Fernandez, A.; Glatz, J.P.; Haas, D.; Konings, R.J.M.; Somers, J.; Toscano, E.; Walker, C.T.; Wegen, D.

2000-01-01

The ITU programme for the development of fuels and targets for transmutation of actinides is presented. The fabrication of various types of oxide fuels/targets by dust-free processes is described. Selected results of post-irradiation examinations of irradiation experiments (SUPERFACT, TRABANT-1, EFTTRA-T4) are presented to demonstrate the irradiation behaviour of these fuels/targets. Finally, the future developments at ITU in this field are described, including the new shielded facility (the MA lab) for fabrication of minor actinide fuels. (authors)

Fuels and targets for incineration and transmutation of actinides: the ITU programme

Energy Technology Data Exchange (ETDEWEB)

Fernandez, A.; Glatz, J.P.; Haas, D.; Konings, R.J.M.; Somers, J.; Toscano, E.; Walker, C.T.; Wegen, D. [Eurpean Commission, Joint Research Centre, Institute for Transuranium Elements, Kurlsruhe (Germany)

2000-07-01

The ITU programme for the development of fuels and targets for transmutation of actinides is presented. The fabrication of various types of oxide fuels/targets by dust-free processes is described. Selected results of post-irradiation examinations of irradiation experiments (SUPERFACT, TRABANT-1, EFTTRA-T4) are presented to demonstrate the irradiation behaviour of these fuels/targets. Finally, the future developments at ITU in this field are described, including the new shielded facility (the MA lab) for fabrication of minor actinide fuels. (authors)

World-wide trend of long-lived radionuclides transmutation studies

International Nuclear Information System (INIS)

Kim, Young Hwan; Lee, Il Hee; Yoo, Jae Hyung

1997-01-01

The objective of this study is to review the concepts of partitioning and transmutation studies which are being conducted in several countries. This review was focused on the analysis of such areas as radiotoxicities of radwaste containing long-lived radionuclides, transmutation by reactors or accelerators, and separation of minor actinides. The world-wide trend of partitioning and transmutation studies was also investigated on the basis of each country's R and D activities in this area. (author). 5 refs., 4 tabs., 3 figs

Separations technology development to support accelerator-driven transmutation concepts

International Nuclear Information System (INIS)

Venneri, F.; Arthur, E.; Bowman, C.

1996-01-01

This is the final report of a one-year Laboratory-Directed Research and Development (LDRD) Project at the Los Alamos National Laboratory (LANL). This project investigated separations technology development needed for accelerator-driven transmutation technology (ADTT) concepts, particularly those associated with plutonium disposition (accelerator-based conversion, ABC) and high-level radioactive waste transmutation (accelerator transmutation of waste, ATW). Specific focus areas included separations needed for preparation of feeds to ABC and ATW systems, for example from spent reactor fuel sources, those required within an ABC/ATW system for material recycle and recovery of key long-lived radionuclides for further transmutation, and those required for reuse and cleanup of molten fluoride salts. The project also featured beginning experimental development in areas associated with a small molten-salt test loop and exploratory centrifugal separations systems

Basic plan of partitioning and transmutation technology development

International Nuclear Information System (INIS)

Ikegami, Tetsuo; Ozawa, Masaki

2003-04-01

Basic plan of partitioning and transmutation technology development has been made in more detail and concrete manner in terms of development goal, nuclides to be portioned and to be transmuted, and development schedule, based on the pre-evaluation results of the Research Evaluation Committee on Research and development of partitioning and transmutation technology for long life nuclides' held in August 2000. A step by step approach, consists of three steps, to reach the goal of partitioning and transmutation technology has been adopted under the recognition that the partitioning and transmutation technology development should be progressed steadily as a long term them. The first step is supposed to be able to attain within about 5 years by the present technology and on the extension of it. Such researches as collective separation of TRU, MA/Ln effective separation, and irradiation experiment of iodine and technetium. The second step is such a goal that is expected to be able to realize the engineering feasibility, within about 15 years, through the progress of science technology in future, although the engineering feasibility is not sufficiently foreseen at present. It will need revolutionary technology or breakthrough. Nuclides to be partitioned and to be transmuted have been selected in view points of 'radioactivity and radio-toxicity', 'geological repository', and 'effective utilization', corresponding to the each step of the development goal. Collaboration with other research organizations and with universities in the world should be pursued. Especially, such collaborations with France, with which information exchange on JOYO/PHENIX irradiation experiments is progressing, and with USA, which has recently developed positive activities in this field, are strongly expected. (author)

New infrastructure for studies of transmutation and fast systems concepts

Science.gov (United States)

Panza, Fabio; Firpo, Gabriele; Lomonaco, Guglielmo; Osipenko, Mikhail; Ricco, Giovanni; Ripani, Marco; Saracco, Paolo; Viberti, Carlo Maria

2017-09-01

In this work we report initial studies on a low power Accelerator-Driven System as a possible experimental facility for the measurement of relevant integral nuclear quantities. In particular, we performed Monte Carlo simulations of minor actinides and fission products irradiation and estimated the fission rate within fission chambers in the reactor core and the reflector, in order to evaluate the transmutation rates and the measurement sensitivity. We also performed a photo-peak analysis of available experimental data from a research reactor, in order to estimate the expected sensitivity of this analysis method on the irradiation of samples in the ADS considered.

Partitioning and transmutation. Annual Report 1999

Energy Technology Data Exchange (ETDEWEB)

Ekberg, C.; Enarsson, Aa.; Gustavsson, C.; Landgren, A.; Liljenzin, J.O.; Spjuth, L. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Chemistry

2000-05-01

The current research project on partitioning and transmutation at the Dept. of Nuclear Chemistry, CTH, has the primary objective to investigate separation processes useful in connection with transmutation of long-lived radionuclides in high level nuclear waste. Partitioning is necessary in order to recover and purify the elements before and after each irradiation in a P and T treatment. In order to achieve a high transmutation efficiency the chemical separation process used must have small losses to various waste streams. At present, only aqueous based separation processes are known to be able to achieve the high recovery and separation efficiencies necessary for a useful P and T process. During 1999 two of the three PhD students in this project have finalised their dissertations. Lena Spjuth has been working with oligo pyridines, triazines and malonamides; Anders Landgren has studied Aliquat-336 and redox kinetics. Two papers, included as appendices in the report, have been separately indexed.

Partitioning and transmutation. Annual Report 1999

International Nuclear Information System (INIS)

Ekberg, C.; Enarsson, Aa.; Gustavsson, C.; Landgren, A.; Liljenzin, J.O.; Spjuth, L.

2000-05-01

The current research project on partitioning and transmutation at the Dept. of Nuclear Chemistry, CTH, has the primary objective to investigate separation processes useful in connection with transmutation of long-lived radionuclides in high level nuclear waste. Partitioning is necessary in order to recover and purify the elements before and after each irradiation in a P and T treatment. In order to achieve a high transmutation efficiency the chemical separation process used must have small losses to various waste streams. At present, only aqueous based separation processes are known to be able to achieve the high recovery and separation efficiencies necessary for a useful P and T process. During 1999 two of the three PhD students in this project have finalised their dissertations. Lena Spjuth has been working with oligo pyridines, triazines and malonamides; Anders Landgren has studied Aliquat-336 and redox kinetics. Two papers, included as appendices in the report, have been separately indexed

Overall assessment of actinide partitioning and transmutation for waste management purposes

International Nuclear Information System (INIS)

Blomeke, J.O.; Croff, A.G.; Finney, B.C.; Tedder, D.W.

1980-01-01

A program to establish the technical feasibility and incentives for partitioning (i.e., recovering) actinides from fuel cycle wastes and then transmuting them in power reactors to shorter-lived or stable nuclides has recently been concluded at the Oak Ridge National Laboratory. The feasibility was established by experimentally investigating the reduction that can be practicably achieved in the actinide content of the wastes sent to a geologic repository, and the incentives for implementing this concept were defined by determining the incremental costs, risks, and benefits. Eight US Department of Energy laboratories and three private companies participated in the program over its 3-year duration. A reference fuel cycle was chosen based on a self-generated plutonium recycle PWR, and chemical flowsheets based on solvent extraction and ion-exchange techniques were generated that have the potential to reduce actinides in fuel fabrication and reprocessing plant wastes to less than 0.25% of those in the spent fuel. Waste treatment facilities utilizing these flowsheets were designed conceptually, and their costs were estimated. Finally, the short-term (contemporary) risks from fuel cycle operations and long-term (future) risks from deep geologic disposal of the wastes were estimated for cases with and without partitioning and transmutation. It was concluded that, while both actinide partitioning from wastes and transmutation in power reactors appear to be feasible using currently identified and studied technology, implementation of this concept cannot be justified because of the small long-term benefits and substantially increased costs of the concept

Partitioning and transmutation. Current developments - 2007. A report from the Swedish reference group on P-T-research

International Nuclear Information System (INIS)

Ahlstroem, Per-Eric; Blomgren, Jan; Eriksson, Marcus; Seltborg, Per; Wallenius, Jan; Westlen, Daniel

2007-06-01

This report is written on behalf of the Swedish reference group for research on partitioning and transmutation. The reference group has been assembled by SKB and its members represent the teams that are active in this field at Swedish universities. The present report summarises the progress in the field through the years 2004-2006. A prerequisite for transmutation by irradiation with neutrons is that the nuclides to be transmuted are separated (partitioned) from the other nuclides in the spent fuel. In particular the remaining uranium must be taken away unless you want to produce more plutonium and other transuranium elements. Separation of the various elements can at least in principle be achieved by mechanical and chemical processes. Currently there exist some large scale facilities for separation of uranium and plutonium from the spent fuel-reprocessing plants. These can, however, not separate the minor actinides - neptunium, americium and curium - from the high level waste that goes to a repository. Plutonium constitutes about 90% of the transuranium elements in fuel from light water reactors. The objective of current research on partitioning is to find and develop processes suitable for separation of the heavier actinides (and possibly some long-lived fission products) on an industrial scale. The objective of current research on transmutation is to define, investigate and develop facilities that may be suitable for transmutation of the aforementioned long-lived radionuclides. The research on partitioning has made important progress in recent years. In some cases one has succeeded to separate americium and curium. Many challenges remain however. Within hydrochemistry one has achieved sufficiently good distribution and separation factors. The focus turns now towards development of an operating process. The search for ligands that give sufficiently good extraction and separation will continue but with less intensity. The emphasis will rather be on improving

Partitioning and transmutation. Current developments - 2007. A report from the Swedish reference group on P-T-research

Energy Technology Data Exchange (ETDEWEB)

Ahlstroem, Per-Eric (ed.) [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Blomgren, Jan [Uppsala Univ. (Sweden). Dept. of Neutron Research; Ekberg, Christian; Englund, Sofie; Fermvik, Anna; Liljenzin, Jan-Olov; Retegan, Teodora; Skarnemark, Gunnar [Chalmers Univ. of Technology, Goeteborg (Sweden); Eriksson, Marcus; Seltborg, Per; Wallenius, Jan; Westlen, Daniel [Royal Inst. of Technology, Stockholm (Sweden)

2007-06-15

This report is written on behalf of the Swedish reference group for research on partitioning and transmutation. The reference group has been assembled by SKB and its members represent the teams that are active in this field at Swedish universities. The present report summarises the progress in the field through the years 2004-2006. A prerequisite for transmutation by irradiation with neutrons is that the nuclides to be transmuted are separated (partitioned) from the other nuclides in the spent fuel. In particular the remaining uranium must be taken away unless you want to produce more plutonium and other transuranium elements. Separation of the various elements can at least in principle be achieved by mechanical and chemical processes. Currently there exist some large scale facilities for separation of uranium and plutonium from the spent fuel-reprocessing plants. These can, however, not separate the minor actinides - neptunium, americium and curium - from the high level waste that goes to a repository. Plutonium constitutes about 90% of the transuranium elements in fuel from light water reactors. The objective of current research on partitioning is to find and develop processes suitable for separation of the heavier actinides (and possibly some long-lived fission products) on an industrial scale. The objective of current research on transmutation is to define, investigate and develop facilities that may be suitable for transmutation of the aforementioned long-lived radionuclides. The research on partitioning has made important progress in recent years. In some cases one has succeeded to separate americium and curium. Many challenges remain however. Within hydrochemistry one has achieved sufficiently good distribution and separation factors. The focus turns now towards development of an operating process. The search for ligands that give sufficiently good extraction and separation will continue but with less intensity. The emphasis will rather be on improving

Validation of PHITS Spallation Models from the Perspective of the Shielding Design of Transmutation Experimental Facility

Science.gov (United States)

Iwamoto, Hiroki; Meigo, Shin-ichiro

2017-09-01

The impact of different spallation models implemented in the particle transport code PHITS on the shielding design of Transmutation Experimental Facility is investigated. For 400-MeV proton incident on a lead-bismuth eutectic target, an effective dose rate at the end of a thick radiation shield (3-m-thick iron and 3-m-thick concrete) calculated by the Liège intranuclear cascade (INC) model version 4.6 (INCL4.6) coupled with the GEMcode (INCL4.6/GEM) yields about twice as high as the Bertini INC model (Bertini/GEM). A comparison with experimental data for 500-MeV proton incident on a thick lead target suggest that the prediction accuracy of INCL4.6/GEM would be better than that of Bertini/GEM. In contrast, it is found that the dose rates in beam ducts in front of targets calculated by the INCL4.6/GEMare lower than those by the Bertini/GEM. Since both models underestimate the experimental results for neutron-production doubledifferential cross sections at 180° for 140-MeV proton incident on carbon, iron, and gold targets, it is concluded that it is necessary to allow a margin for uncertainty caused by the spallation models, which is a factor of two, in estimating the dose rate induced by neutron streaming through a beam duct.

Transmutation of long-lived fission product (137Cs, 90Sr) by a reactor-accelerator system

International Nuclear Information System (INIS)

Toyama, Shin-ichi; Takashita, Hirofumi; Konashi, Kenji; Sasao, Nobuyuki; Sato, Isamu.

1990-01-01

The report discusses the transmutation of long-lived fission products by a reactor and accelerator. It is important to take some criteria into consideration in transmutation disposal. To satisfy the criteria, a combined system of a reactor and an accelerator is proposed for the transmutation. An outline of the transmutation reactor and the accelerator is presented. The transmutation reactor has the ability to transmute a large quantity of fission products. However, it is desirable to have a high transmutation rate as well as a large disposal ability. Besides the transmutation property, it is necessary to investigate the physics of the transmutation reactor such as nuclear characteristics and burnup properties in order to obtain the most suitable, high performance core concept. A study on those properties is also presented. A high power accelerator is required for the transmutation. So a test linac is developed to accelerate high intensity beams. (N.K.)

Partitioning and transmutation - Technical feasibility, proliferation resistance and safeguardability

International Nuclear Information System (INIS)

Schenkel, R.; Glatz, J.-P.; Magill, J.; Mayer, K.

2001-01-01

Full text: The advantages of partitioning and transmutation (P and T) of minor actinides and selected fission products are largely discussed and described in literature. The advantages of separation of the long-lived alpha-emitters for the long-term storage of highly radioactive waste have been highlighted. After separation, these nuclides shall be transmuted by means of a dedicated reactor or accelerator driven system into shorter-lived fission products that are less hazardous. This, however, requires the development and implementation of a P and T fuel cycle, involving chemical separation of the minor actinides and the fabrication of MA containing fuels or targets. Concepts for P and T fuel cycles have been developed and technical issues are being addressed in various research programs. With the recognition of the proliferation potential associated with the minor actinides by the IAEA, also the proliferation and safeguards aspects need to be addressed. It is important to raise these points at an early stage of process development, in order to identify potential problems and to develop appropriate solutions. The oxide fuels used worldwide in thermal reactor systems for energy production are reprocessed by aqueous techniques. Therefore these systems, primarily the PUREX process, are fully developed and implemented commercially. Furthermore, the safeguards approach is fully implemented in existing facilities, covering uranium and plutonium. Pyroprocess systems have largely been associated with fast reactors and metallic fuels and their development has therefore only reached the pilot-scale stage and the feasibility of minor actinide (MA) separation still needs to be demonstrated. Hydrometallurgical and pyrochemical reprocessing should however not be considered as competing but rather as complementary technologies. For instance in a so-called double strata concept (foreseen for instance in the Japanese OMEGA project), the PUREX process (first stratum) would be

Transmuted Lindley-Geometric Distribution and its applications

OpenAIRE

Merovci, Faton; Elbatal, Ibrahim

2013-01-01

A functional composition of the cumulative distribution function of one probability distribution with the inverse cumulative distribution function of another is called the transmutation map. In this article, we will use the quadratic rank transmutation map (QRTM) in order to generate a flexible family of probability distributions taking Lindley geometric distribution as the base value distribution by introducing a new parameter that would offer more distributional flexibility. It will be show...

Transmuted New Generalized Inverse Weibull Distribution

Directory of Open Access Journals (Sweden)

Muhammad Shuaib Khan

2017-06-01

Full Text Available This paper introduces the transmuted new generalized inverse Weibull distribution by using the quadratic rank transmutation map (QRTM scheme studied by Shaw et al. (2007. The proposed model contains the twenty three lifetime distributions as special sub-models. Some mathematical properties of the new distribution are formulated, such as quantile function, Rényi entropy, mean deviations, moments, moment generating function and order statistics. The method of maximum likelihood is used for estimating the model parameters. We illustrate the flexibility and potential usefulness of the new distribution by using reliability data.

Transmutation of Tc-99 and I-129 in fission reactors. A calculational study

International Nuclear Information System (INIS)

Kloosterman, J.L.; Li, J.M.

1995-03-01

The HWR is a better candidate for large-scale transmutation of long-lived fission products. When target pins containing either Tc-99 or I-129 are positioned in the centre of each fuel bundle of a 935 MW e CANDU reactor, the transmutation half lives are 44 and 20 years, respectively, and the gross transmutation rates 60 and 48 kg/a. The positive coolant void coefficient is reduced in both cases with about 30%. When Tc-99 target pins are positioned in the moderator between the fuel bundles, the transmutation half life becomes 25 years and the gross transmutation rate 106 kg/a. This means that one HWR can serve four PWRs with equal power. The fast reactor seems most promising. When Tc-99 target pins are irradiated in moderated subassemblies in the inner core of Superphenix (∼1240 MW e ), a transmutation half life of 15 years is obtained with a gross transmutation rate of 122 kg/a. These values become 18 years and 101 kg/a when non-moderated subassemblies are used for the irradiation. This implies that one fast reactor can serve four to five PWRs with equal power. The PWR seems not very effective for transmutation of Tc-99. Large inventories are needed to obtain a Tc-99 transmutation rate equal to the production rate (18 kg/a for a 900 MW e PWR). When all guide tubes of an UO 2 fuelled PWR are filled with Tc-99 with density of 5 g cm -3 , the transmutation half life is 39 years and the gross transmutation rate 64 kg/a. (orig./GL)

Comparative study for minor actinide transmutation in various fast reactor core concepts

International Nuclear Information System (INIS)

Ohki, S.

2001-01-01

A comparative evaluation of minor actinide (MA) transmutation property was performed for various fast reactor core concepts. The differences of MA transmutation property were classified by the variations of fuel type (oxide, nitride, metal), coolant type (sodium, lead, carbon dioxide) and design philosophy. Both nitride and metal fuels bring about 10% larger MA transmutation amount compared with oxide fuel. The MA transmutation amount is almost unchanged by the difference between sodium and lead coolants, while carbon dioxide causes a reduction by about 10% compared with those. The changes of MA transmutation property by fuel and coolant types are comparatively small. The effects caused by the difference of core design are rather significant. (author)

Transmutation of technetium into stable ruthenium in high flux conceptual research reactor

International Nuclear Information System (INIS)

Amrani, N.; Boucenna, A.

2007-01-01

The effectiveness of transmutation for the long lived fission product technetium-99 in high flux research reactor, considering its large capture cross section in thermal and epithermal region is evaluated. The calculation of Ruthenium concentration evolution under irradiation was performed using Chain Solver 2.20 code. The approximation used for the transmutation calculation is the assumption that the influence of change in irradiated materials structures on the reactor operator mode characteristics is insignificant. The results on Technetium transmutation in high flux research reactor suggested an effective use of this kind of research reactors. The evaluation brings a new concept of multi-recycle Technetium transmutation using HFR T RAN (High Flux Research Reactor for Transmutation)

A new concept for accelerator driven transmutation of nuclear wastes

International Nuclear Information System (INIS)

Arthur, E.D.

1991-01-01

A new concept for an accelerator-driven transmutation system is described. The central feature of the concept is generation of intense fluxes of thermal neutrons. In the system all long-lived radionuclides comprising high-level nuclear waste can be transmuted efficiently. Transmutation takes place in a unique, low material inventory environment. Presently two principal areas are being investigated for application of the concept. The first is associated with cleanup of defense high-level waste at DOE sites such as Hanford. The second, longer term area involves production of electric power using a coupled accelerator-multiplying blanket system. This system would utilize natural thorium or uranium and would transmute long-lived components of high-level waste concurrently during operation. 5 refs., 5 figs

Neutron data for accelerator-driven transmutation technologies. Annual Report 2003/2004

International Nuclear Information System (INIS)

Blomgren, J.; Hildebrand, A.; Nilsson, L.; Mermod, P.; Olsson, N.; Pomp, S.; Oesterlund, M.

2004-08-01

The project NATT, Neutron data for Accelerator-driven Transmutation Technology, is performed within the nuclear reactions group of the Dept. of Neutron Research, Uppsala univ. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group has previously developed two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: Analysis and documentation has been finalized of previously performed measurements of elastic neutron scattering from hydrogen at 96 MeV. The results corroborate the normalization of previously obtained data at TSL, which have been under debate. This is of importance since this reaction serves as reference for many other measurements. Compelling evidence of the existence of three-body forces in nuclei has been obtained. Within the project, one PhD exam and one licentiate exam has been awarded. One PhD exam and one licentiate exam has been awarded for work closely related to the project. A new neutron beam facility with significantly improved performance has been built and commissioned at TSL

Neutron data for accelerator-driven transmutation technologies. Annual Report 2003/2004

Energy Technology Data Exchange (ETDEWEB)

Blomgren, J.; Hildebrand, A.; Nilsson, L.; Mermod, P.; Olsson, N.; Pomp, S.; Oesterlund, M. [Uppsala Univ. (Sweden). Dept. for Neutron Research

2004-08-01

The project NATT, Neutron data for Accelerator-driven Transmutation Technology, is performed within the nuclear reactions group of the Dept. of Neutron Research, Uppsala univ. The activities of the group are directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group has previously developed two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: Analysis and documentation has been finalized of previously performed measurements of elastic neutron scattering from hydrogen at 96 MeV. The results corroborate the normalization of previously obtained data at TSL, which have been under debate. This is of importance since this reaction serves as reference for many other measurements. Compelling evidence of the existence of three-body forces in nuclei has been obtained. Within the project, one PhD exam and one licentiate exam has been awarded. One PhD exam and one licentiate exam has been awarded for work closely related to the project. A new neutron beam facility with significantly improved performance has been built and commissioned at TSL.

Transmutation of minor actinides in a spherical torus tokamak fusion reactor, FDTR

International Nuclear Information System (INIS)

Feng, K.M.; Zhang, G.S.; Deng, M.G.

2003-01-01

In this paper, a concept for the transmutation of minor actinide (MA) nuclear wastes based on a spherical torus (ST) tokamak reactor, FDTR, is put forward. A set of plasma parameters suitable for the transmutation blanket was chosen. The 2-D neutron transport code TWODANT, the 3-D Monte Carlo code MCNP/4B, the 1-D neutron transport and burn-up calculation code BISON3.0 and their associated data libraries were used to calculate the transmutation rate, the energy multiplication factor and the tritium breeding ratio of the transmutation blanket. The calculation results for the system parameters and the actinide series isotopes for different operation times are presented. The engineering feasibility of the center-post (CP) of FDTR has been investigated and the results are also given. A preliminary neutronics calculation based on an ST transmutation blanket shows that the proposed system has a high transmutation capability for MA wastes. (author)

Studies on separation, conversion and transmutation of long-living radionuclides. A contribution to advanced disposal of high-level radioactive wastes

International Nuclear Information System (INIS)

Modolo, Giuseppe

2014-01-01

The future role and acceptance of nuclear energy will be decisively determined by the safe operation of existing and future facilities and by convincing solutions for nuclear waste management. With respect to the long half-lives of some radionuclides (actinides and fission products) and the related question as to whether the release of radionuclides from a repository can be prevented over very long periods of time, alternatives to the direct disposal of spent nuclear fuels are discussed internationally. As a potential complementary solution, the technological option with partitioning and transmutation (P and T) is considered. This method separates and converts the long-lived radionuclides into stable, short-lived nuclides via neutron reactions in dedicated facilities. Against this background, the first main chapter of the present work looks at the chemical separation of actinides from high-level reprocessing wastes. In order to achieve a better understanding of the processes at the molecular level, basic investigations were also performed on separating actinides(III) via liquid-liquid or liquid-solid extraction. At the same time, reversible processes were developed and tested on the laboratory scale with the aid of mixer-settlers and centrifugal extractors. The subsequent chapter focuses on separating the long-lived fission product iodine-129 from radioactive wastes as well as from process effluents arising from reprocessing. As part of this work, different simple chemical and physical techniques were developed for complete recovery with respect to transmutation or conditioning in host matrices that are sufficiently stable for final storage. Its high mobility and radiological properties make iodine-129 relevant for the long-term safety assessment of final repositories. In addition, transmutation experiments on iodine-127/129 targets were performed using high-energy protons (145-2600 MeV). Due to the expected low cross sections (<100 mb), transmutation with protons

Sensitivity analysis of minor actinides transmutation to physical and technological parameters

International Nuclear Information System (INIS)

Kooyman, T.; Buiron, L.

2015-01-01

Minor actinides transmutation is one of the 3 main axis defined by the 2006 French law for management of nuclear waste, along with long-term storage and use of a deep geological repository. Transmutation options for critical systems can be divided in two different approaches: (a) homogeneous transmutation, in which minor actinides are mixed with the fuel. This exhibits the drawback of 'polluting' the entire fuel cycle with minor actinides and also has an important impact on core reactivity coefficients such as Doppler Effect or sodium void worth for fast reactors when the minor actinides fraction increases above 3 to 5% depending on the core; (b) heterogeneous transmutation, in which minor actinides are inserted into transmutation targets which can be located in the center or in the periphery of the core. This presents the advantage of decoupling the management of the minor actinides from the conventional fuel and not impacting the core reactivity coefficients. In both cases, the design and analyses of potential transmutation systems have been carried out in the frame of Gen IV fast reactor using a 'perturbation' approach in which nominal power reactor parameters are modified to accommodate the loading of minor actinides. However, when designing such a transmutation strategy, parameters from all steps of the fuel cycle must be taken into account, such as spent fuel heat load, gamma or neutron sources or fabrication feasibility. Considering a multi-recycling strategy of minor actinides, an analysis of relevant estimators necessary to fully analyze a transmutation strategy has been performed in this work and a sensitivity analysis of these estimators to a broad choice of reactors and fuel cycle parameters has been carried out. No threshold or percolation effects were observed. Saturation of transmutation rate with regards to several parameters has been observed, namely the minor actinides volume fraction and the irradiation time. Estimators of interest that have been

Analysis of minor actinides transmutation for a Molten Salt Fast Reactor

International Nuclear Information System (INIS)

Yu, Chenggang; Li, Xiaoxiao; Cai, Xiangzhou; Zou, Chunyan; Ma, Yuwen; Han, Jianlong; Chen, Jingen

2015-01-01

Highlights: • The transmutation of MA in a 500 MWth MSFR is analyzed. • A larger MA loading can enhance the MA transmutation and deepen the burnup. • The MA transmutation efficiency can reach 95%. • The FTC can satisfy the safe operating requirement during the entire operating. - Abstract: As one of the six candidate reactors chosen by the Generation IV International Forum (GIF), Molten Salt Fast Reactor (MSFR) has many outstanding advantages and features for advanced nuclear fuel utilization. Effective transmutation of minor actinides (MA) could be attained in this kind of fast reactor, which is of importance in the future closed nuclear fuel cycle scenario. In this work, we attempt to study the MA transmutation capability in a MSFR with power of 500 MWth by analyzing the neutronics characteristics for different MA loadings. The calculated results show that MA loading plays an important role in the reactivity evolution of the MSFR. A larger MA loading is favorable to improving the MA transmutation performance and simultaneously to reducing the fissile consumption. When MA = 18.17 mol%, the transmutation fraction can achieve to about 95% on iso-breeding. We also find that although the fuel temperature coefficient (FTC) decreases with the increasing MA loading, it is still negative enough to keep the safety of the MSFR during the whole operation time. The MA contribution to the effective delayed neutron fraction (EDNF) and the intensity of spontaneous fission neutron (ISFN) are also analyzed. Also MA loading can affect the EDNF during the operation and the ISFN of the MSFR is dominated by 244 Cm. Finally, we analyze the effect of the core power on MA transmutation capability. The result shows that for all the operating powers the depletion ratio of MA to HN increases with time and reaches a maximum value. And additional MA should be fed into the fuel salt before the MA depletion ratio reaches the peak value to improve its transmutation capability. The net

Study on the LLFPs transmutation in a super-critical water-cooled fast reactor

International Nuclear Information System (INIS)

Lu Haoliang; Ishiwatari, Yuki; Oka, Yoshiaki

2011-01-01

Research highlights: → Transmutation of LLFPs with a super-criticial water cooled fast reactor. → Transmutation of iodine and cesium without the isotopic separation. → The transmuted isotope was mixed with UO 2 to reduce the effect of self-shielding. → A weak neutron moderator Al 2 O 3 was used to suppress the creation of 135 Cs from 133 Cs. - Abstract: The performance of the super-critical water-cooled fast reactor (Super FR) for the transmutation treatment of long-lived fission products (LLFPs) was evaluated. Two regions with the soft neutron spectrum, which is of great benefit to the LLFPs transmutation, can be utilized in the Super FR. First region is in the blanket assembly due to the ZrH 1.7 layer which was utilized to slow down the fast neutrons to achieve a negative void reactivity. Second region is in the reflector region of core like other metal-cooled fast reactors. The LLFPs selected in the transmutation analysis include 99 Tc, 129 I and 135 Cs discharged from LWR or fast reactor. Their isotopes, such as 127 I, 133 Cs, 134 Cs and 137 Cs were also considered to avoid the separation. By loading the isotopes ( 99 Tc or 127 I and 129 I) in the blanket assembly and the reflector region simultaneously, the transmutation rates of 5.36%/GWe year and 2.79%/GWe year can be obtained for 99 Tc and 129 I, respectively. The transmuted amounts of 99 Tc and 129 I are equal to the yields from 11.8 and 6.2 1000 MWe-class PWRs. Because of the very low capture cross section of 135 Cs and the effect of other cesium isotopes, 135 Cs was loaded with three rings of assemblies in the reflector region to make the transmuted amount be larger than the yields of two 1000 MWe-class PWRs. Based on these results, 99 Tc and 129 I can be transmuted conveniently and higher transmutation performance can be obtained in the Super FR. However, the transmutation of 135 Cs is very difficult and the transmuted amount is less than that produced by the Super FR. It turns out that the

Preliminary analyses of neutronics schemes for three kinds waste transmutation blankets of fusion-fission hybrid

International Nuclear Information System (INIS)

Zhang Mingchun; Feng Kaiming; Li Zaixin; Zhao Fengchao

2012-01-01

The neutronics schemes of the helium-cooled waste transmutation blanket, sodium-cooled waste transmutation blanket and FLiBe-cooled waste transmutation blanket were preliminarily calculated and analysed by using the spheroidal tokamak (ST) plasma configuration. The neutronics properties of these blankets' were compared and analyzed. The results show that for the transmutation of "2"3"7Np, FLiBe-cooled waste transmutation blanket has the most superior transmutation performance. The calculation results of the helium-cooled waste transmutation blanket show that this transmutation blanket can run on a steady effective multiplication factor (k_e_f_f), steady power (P), and steady tritium production rate (TBR) state for a long operating time (9.62 years) by change "2"3"7Np's initial loading rate of the minor actinides (MA). (authors)

Actinide and fission product separation and transmutation

International Nuclear Information System (INIS)

1991-01-01

The first international information exchange meeting on actinide and fission product separation and transmutation, took place in Mito in Japan, on 6-8 November 1990. It starts with a number of general overview papers to give us some broad perspectives. Following that it takes a look at some basic facts about physics and about the quantities of materials it is talking about. Then it proceeds to some specific aspects of partitioning, starting with evolution from today commercially applied processes and going on to other possibilities. At the end of the third session it takes a look at the significance of partitioning and transmutation of actinides before it embarks on two sessions on transmutation, first in reactors and second in accelerators. The last session is designed to throw back into the discussion the main points which need to be looked at when considering future work in this area. (A.L.B.)

Actinide and fission product separation and transmutation

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-07-01

The first international information exchange meeting on actinide and fission product separation and transmutation, took place in Mito in Japan, on 6-8 November 1990. It starts with a number of general overview papers to give us some broad perspectives. Following that it takes a look at some basic facts about physics and about the quantities of materials it is talking about. Then it proceeds to some specific aspects of partitioning, starting with evolution from today commercially applied processes and going on to other possibilities. At the end of the third session it takes a look at the significance of partitioning and transmutation of actinides before it embarks on two sessions on transmutation, first in reactors and second in accelerators. The last session is designed to throw back into the discussion the main points which need to be looked at when considering future work in this area. (A.L.B.)

Code development and analyses within the area of transmutation and safety

International Nuclear Information System (INIS)

Maschek, W.

2002-01-01

A strong code development is going on to meet various demands resulting from the development of dedicated reactors for transmutation and incineration. Code development is concerned with safety codes and general codes needed for assessing scenarios and transmutation strategies. Analyses concentrate on various ADS systems with solid and liquid molten salt fuels. Analyses deal with ADS Demo Plant (5th FP EU) and transmuters with advanced fuels

A low power ADS for transmutation studies in fast systems

Science.gov (United States)

Panza, Fabio; Firpo, Gabriele; Lomonaco, Guglielmo; Osipenko, Mikhail; Ricco, Giovanni; Ripani, Marco; Saracco, Paolo; Viberti, Carlo Maria

2017-12-01

In this work, we report studies on a fast low power accelerator driven system model as a possible experimental facility, focusing on its capabilities in terms of measurement of relevant integral nuclear quantities. In particular, we performed Monte Carlo simulations of minor actinides and fission products irradiation and estimated the fission rate within fission chambers in the reactor core and the reflector, in order to evaluate the transmutation rates and the measurement sensitivity. We also performed a photo-peak analysis of available experimental data from a research reactor, in order to estimate the expected sensitivity of this analysis method on the irradiation of samples in the ADS considered.

Comparative analysis of Pu spread resistance of chemico-technological (out of pile) complexes of electronuclear molten salt and heavy water blanket facilities for transmutation

International Nuclear Information System (INIS)

Volk, V.I.; Vakhrushin, A.Yu.; Gorbunov, V.F.; Kushnikov, V.V.

1997-01-01

Technological processes used for radiochemical reprocessing of molten salt and heavy water blankets of an electronuclear facility for Pu transmutation and Pu distribution in those processes are characterized. Below the major parameters are given that affect the resistance of the technological to Pu proliferation. Types of Pu migration: process losses, accident related losses, theft. Factors affecting migration are total inventory of Pu in a reprocessing complex, purity of Pu and its compounds, chemical condition of Pu, the feasibility of equipping technological processes with instruments of control. The comparative analysis carried out taking into account the above parameters established that the technological processes related to heavy water blanket reprocessing, specifically a homogeneous (solution) option, are much more resistant to Pu proliferation, including both Pu migration to the environment and the unsanctioned withdrawal of Pu from the technological process. 5 refs., 4 figs

Research on transmutation and accelerator-driven systems at the Forschungszentrum Karlsruhe

International Nuclear Information System (INIS)

Knebel, J.U.; Heusener, G.

2000-01-01

Transmutation is considered a promising technology worldwide for significantly reducing the amount and, thereby, the long-term radiotoxicity of high active waste (HAW) produced by the operation of nuclear power plants such as light water reactors (LWR). The maximum reduction of radiotoxicity could be by a factor of about 100. Transmutation is thus an alternative to the direct deposition of large volumes of highly radioactive waste. Transmutation presents the possibility of closing the fuel cycle including the minor actinides. Plutonium, minor actinides and long-lived fission products can be transmuted in a so called Accelerator Driven Sub-critical System (ADS), which consists of an accelerator, a target module and a subcritical blanket. This paper describes the work performed at Forschungszentrum Karlsruhe which is critically evaluating an ADS mainly with respect to its potential for transmuting minor actinides, to its feasibility and to safety aspects. The work is being done in the area of core design, neutronics, safety, system analyses, materials and corrosion. (orig.) [de

Proposed partitioning and transmutation of long-lived nuclear wastes

International Nuclear Information System (INIS)

Van Tuyle, G.J.; Rawlins, J.A.

1991-01-01

A means of transmuting key long-lived nuclear wastes, primarily the minor actinides (Np, Am, Cm) and iodine, using a hybrid proton accelerator and sub-critical lattice, is proposed. By partitioning light water reactor (LWR) spent fuel and by transmuting key elements, such as the plutonium, the minor actinides, and a few of the long-lived fission products, some of the most significant challenges in building a waste repository can be substantially reduced. The proposed machine would transmute the minor actinides and the iodine produced by 75 LWRs, and would generate usable electricity (beyond that required to run the large accelerator) of 850 MW e . 14 refs., 10 figs

The transmutation of americium: the Ecrix experiments in Phenix

International Nuclear Information System (INIS)

Garnier, J.C.; Schmidt, N.; Croixmarie, Y.; Ottaviani, J.P.; Varaine, F.; Saint Jean, C. de

1999-01-01

The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be 11 B 4 C and CaH 2 for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO X pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

Status report on actinide and fission product transmutation studies

International Nuclear Information System (INIS)

1997-06-01

The management of radioactive waste is one of the key issues in today's political and public discussions on nuclear energy. One of the fields that looks into the future possibilities of nuclear technology is the neutronic transmutation of actinides and of some most important fission products. Studies on transmutation of actinides are carried out in various countries and at an international level. This status report which gives an up-to-date general overview of current and planned research on transmutation of actinides and fission products in non-OECD countries, has been prepared by a Technical Committee meeting organized by the IAEA in September 1995. 168 refs, 16 figs, 34 tabs

Towards standardized calculation tools for the Accelerator-Driven Systems and their application to various scenarios for nuclear waste transmutation

International Nuclear Information System (INIS)

Cometto, M.

2003-01-01

This thesis discusses the question of partitioning and transmutation of actinides and some long-lived fission products as a way of reducing the mass and radio-toxicity of wastes from nuclear power facilities. Numerical benchmarking and computational exercises carried out in related projects are discussed and the quantitative assessment of the advantages and drawbacks of various transmutation strategies are discussed, as is the role of Accelerator-Driven Systems (ADS) and Advanced Fast Reactors (FR) in advanced nuclear fuel cycles. According to the author, the study allows three main options in nuclear waste management - open cycle, plutonium recycling and the recycling of all actinides - to be compared. The last part of the dissertation is dedicated to two phase-out schemes employing either ASDs or critical reactors

Transmutation of radioactive waste: Effect on the nuclear fuel cycle

International Nuclear Information System (INIS)

Rasmussen, N.C.; Pigford, T.H.

1997-01-01

A committee of the National Research Council reviewed three concepts for transmuting radionuclides recovered from the chemical reprocessing of commercial light-water-reactor (LWR) fuel: LWR transmutation reactors fueled with recycled actinides, advanced liquid-metal reactors (ALMRs), and accelerator-driven subcritical reactors for transmutation of waste (ATW). The concepts were evaluated in terms of: (1) the extent to which waste disposal would benefit from transmutation, (2) time required to reduce the total inventory of radionuclides in the waste and fuel cycle, (3) the complexity of the overall transmutation system, (4) the extent of new development required, and (5) institutional and economic problems of operating such systems. Transmutation could affect geologic disposal of waste by reducing the inventory of transuranics (TRUs), fission products, and other radionuclides in the waste. Reducing the inventory of transuranics does not necessarily affect radiation doses to people who use contaminated ground water if the dissolution rate of transuranics in waste is controlled by elemental solubilities. However, reducing inventories of Am and Pu would decrease potential hazards from human intrusion. The likelihood for underground nuclear criticality would also be reduced. The long-lived fission products Tc-99, I-129, Cs-135 and others typically contribute most to the long-term radiation doses to future populations who use contaminated water from the repository. Their transmutation requires thermal or epithermal neutrons, readily available in LWR and ATW transmutors. ALMR and LWR transmutors would require several hundred years to reduce the total transuranic inventory by even a factor of 10 at constant electric power, and thousands of years for a hundred-fold reduction. For the same electrical power, the ATW could reduce total transuranic inventory about tenfold more rapidly, because of its very high thermal-neutron flux. However, extremely low process losses would be

Feasibility of waste transmutation using accelerator-driven IRIS subcritical system

International Nuclear Information System (INIS)

Petroviae, B.; Carelli, M.; Paramonov, D.

2001-01-01

Waste transmutation is considered for reducing radio-toxicity of nuclear waste generated in power reactors. Accelerator driven subcritical systems (ADS) offer certain advantages over the use of nuclear reactors. Transmutation of fission products (e.g. 99 Tc) generally requires thermal neutron spectrum, while for actinides fast spectrum provides better performance. Proposed solutions to this problem include a multi-strata approach as well as a multi-zone (thermal/fast-spectrum) single systems. In this paper we examine the feasibility of employing a dual-spectrum two-zone accelerator-driven IRIS subcritical for waste transmutation. (author)

Multi-faceted evaluation for nuclear fuel cycles with transmutation

International Nuclear Information System (INIS)

Nishihara, Kenji

2015-03-01

Environment impact, economy and proliferation resistance were estimated for nuclear fuel cycles involving transmutation by fast reactor and accelerator-driven system in equilibrium state. As a result, the transmutation scenario using only fast reactor was superior to the scenarios combined with accelerator-driven system in all estimation, but the differences were insignificant. (author)

Transmutation of Minor Actinide in well thermalized neutron field and application of advanced neutron source (ANS)

International Nuclear Information System (INIS)

Iwasaki, Tomohiko; Hirakawa, Naohiro

1995-01-01

Transmutation of Minor Actinide (MA) in a well thermalized neutron field was studied. Since MA nuclides have large effective cross sections in the well thermalized neutron field, the transmutation in the well thermalized neutron field has an advantage of high transmutation rate. However, the transmutation rate largely decreases by accumulation of 246 Cm when MA is transmuted only in the well thermalized neutron field for a long period. An acceleration method of burn-up of 246 Cm was studied. High transmutation rate can be obtained by providing a neutron field with high flux in the energy region between 1 and 100 eV. Two stage transmutation using the well thermalized neutron field and this field can transmute MA rapidly. The applicability of the Advanced Neutron Source (ANS) to the transmutation of MA was examined for a typical MA with the composition in the high-level waste generated in the conventional PWR. If the ANS is applied without changing the fuel inventory, the amount of MA which corresponds to that produced by a conventional 1,175 MWe PWR in one year can be transmuted by the ANS in one year. Furthermore, the amount of the residual can be reduced to about 1g (10 -5 of the initial MA weight) by continuing the transmutation for 5 years owing to the two stage transmutation. (author)

A study of γ-ray source for the transmutation

International Nuclear Information System (INIS)

Nomura, Masahiro; Takahashi, Hiroshi.

1996-07-01

PNC is developing high power CW electron linac for various applications, those are the transmutation of the fission products, Free Electron Laser (FEL), the positron source and so on. Especially, the transmutation by the electron linac has been studied for several years. As the results, high flux and high energy γ-ray (∼15 MeV) is required, one of the big problems is that plenty of transmutation energy is needed and the narrow γ-ray energy spectrum can reduce the transmutation energy. The γ-rays can be produced by synchrotron radiation, FEL and laser compton scattering. Those methods were described briefly and compared. As a result, the laser compton scattering is one of the good methods to produce high energy γ-ray. However the cross section between electron and photon is small and the scattered photon energy spectrum is not so narrow that the transmutation energy is reduced drastically. To enhance the interaction between electron and photon, the super cavity is proposed. And some experiments are in progress. To reduce the transmutation energy, scattered electron must be reused by the storage ring. If the scattered electrons are not used for producing γ-ray, the efficiency is less than 1%. In our system, the efficiency can be increased to 20% by reusing scattered electrons. But this efficiency is still low. To increase the efficiency, the RF bucket must be enlarged. If the momentans compaction factor α can be reduced, the RF bucket can be enlarged. And the storage ring must be designed to have small value of the α. The electron energy dependency of efficiency is investigated, too. In short word, it is difficult to increase the efficiency drastically by changing electron energy. This work was conducted as a part of the collaboration work between PNC and BNL. (author)

Vortex transmutation.

Science.gov (United States)

Ferrando, Albert; Zacarés, Mario; García-March, Miguel-Angel; Monsoriu, Juan A; de Córdoba, Pedro Fernández

2005-09-16

Using group theory arguments and numerical simulations, we demonstrate the possibility of changing the vorticity or topological charge of an individual vortex by means of the action of a system possessing a discrete rotational symmetry of finite order. We establish on theoretical grounds a "transmutation pass" determining the conditions for this phenomenon to occur and numerically analyze it in the context of two-dimensional optical lattices. An analogous approach is applicable to the problems of Bose-Einstein condensates in periodic potentials.

Vortex Transmutation

International Nuclear Information System (INIS)

Ferrando, Albert; Garcia-March, Miguel-Angel; Zacares, Mario; Monsoriu, Juan A.; Cordoba, Pedro Fernandez de

2005-01-01

Using group theory arguments and numerical simulations, we demonstrate the possibility of changing the vorticity or topological charge of an individual vortex by means of the action of a system possessing a discrete rotational symmetry of finite order. We establish on theoretical grounds a 'transmutation pass rule' determining the conditions for this phenomenon to occur and numerically analyze it in the context of two-dimensional optical lattices. An analogous approach is applicable to the problems of Bose-Einstein condensates in periodic potentials

Transmutations across hierarchical levels

International Nuclear Information System (INIS)

O'Neill, R.V.

1977-01-01

The development of large-scale ecological models depends implicitly on a concept known as hierarchy theory which views biological systems in a series of hierarchical levels (i.e., organism, population, trophic level, ecosystem). The theory states that an explanation of a biological phenomenon is provided when it is shown to be the consequence of the activities of the system's components, which are themselves systems in the next lower level of the hierarchy. Thus, the behavior of a population is explained by the behavior of the organisms in the population. The initial step in any modeling project is, therefore, to identify the system components and the interactions between them. A series of examples of transmutations in aquatic and terrestrial ecosystems are presented to show how and why changes occur. The types of changes are summarized and possible implications of transmutation for hierarchy theory, for the modeler, and for the ecological theoretician are discussed

Evaluation of transmutation performance of long-lived fission products with a super fast reactor

International Nuclear Information System (INIS)

Lu, Haoliang; Han, Chiyoung; Oka, Yoshiaki; Ikejiri, Satoshi; Ishiwatari, Yuki

2009-01-01

The performance of the Super Fast Reactor for transmutation treatment of long-lived fission products (LLFPs) was evaluated. Two regions with soft neutron spectrum, which is of great benefit to the LLFPs transmutation, can be utilized in the Super Fast Reactor. First is in the blanket assembly due to the ZrH 1.7 layer which can slow down the fast neutrons. Second is in the reflector region of core like other metal-cooled fast reactors. The LLFPs selected of transmutation analysis include 99 Tc, 129 I and 135 Cs discharged from LWR. Their isotopes, such as 127 I, 133 Cs, 134 Cs and 137 Cs were also considered. By loading the isotopes ( 99 Tc or 127 I and 129 I) in the blanket assembly and the reflector region simultaneously, the transmutation rates of 5.36%/GWe·y and 2.79%/GWe.y can be obtained for 99 Tc and 129 I, respectively. The transmuted amounts of 99 Tc and 129 I are equal to the outputs from 11.8 and 6.2 1000MWe-class PWRs. Because of the very low capture cross section of 135 Cs and the effect of other cesium isotopes, 135 Cs was loaded with three rings of assemblies in the reflector region to make the transmuted amount be larger than the yields of two 1000MWe-class PWRs. Based on these results, 99 Tc and 129 I can be transmuted conveniently and higher transmutation performance can be obtained by the Super Fast Reactor. However, the transmutation of 135 Cs is very difficult and the transmuted amount is less than that produced by the Super Fast Reactor. It turns out that the 135 Cs transmutation is a challenge not only for the Super Fast Reactor but also for other commercial fast reactors. (author)

Partitioning and transmutation: Radioactive waste management option

International Nuclear Information System (INIS)

Stanculescu, A.

2005-01-01

Growing world population with increasing energy needs, especially in the developing countries, Threat of global warming due to CO 2 emissions demands non-fossil electricity production. Nuclear will have to be part of a sustainable mix of energy production options Figures show that 350 GWe worldwide capacity is 'nuclear'. Present worldwide spent fuel (containing high Pu inventory) and HLW would need large repositories. In view of the previous facts this lecture deals Partitioning and transmutation as radioactive waste management option. Partitioning and transmutation (P and T) is a complex technology i.e. advanced reprocessing, and demand transuranics fuel fabrication plants, as well as innovative and/or dedicated transmutation reactors. In addition to U, Pu, and 129 I, 'partitioning' extracts from the liquid high level waste the minor actinides (MA) and the long-lived fission products (LLFP) 99-Tc, 93-Zr, 135-Cs, 107-Pd, and 79-Se). 'Transmutation' requires fully new fuel fabrication plants and reactor technologies to be developed and implemented on industrial scale. Present LWRs are not suited for MA and LLFP transmutation (safety consideration, plant operation, poor incineration capability). Only specially licensed LWRs can cope with MOX fuel; for increased Pu loadings (up to 100%), special reactor designs (e.g., ABB80+) are required; a combination of these reactor types could allow Pu inventory stabilization. Long-term waste radiotoxicity can be effectively reduced only if transuranics are 'incinerated' through fission with very hard neutron spectra. New reactor concepts (dedicated fast reactors, Accelerator Driven Systems (ADS), fusion/fission hybrid reactors) have been proposed as transmuters/incinerators. Significant Pu+MAs incineration rates can be achieved in symbiotic scenarios: LWR-MOX and dedicated fast reactors; fast neutron spectrum ADS mainly for MA incineration; very high thermal flux ADS concepts could also provide a significant transuranics

Photo-transmutation of {sup 100}Mo to {sup 99}Mo with Laser-Compton Scattering Gamma-ray

Energy Technology Data Exchange (ETDEWEB)

Lee, Jiyoung; Rehman, Haseeb ur; Kim, Yonghee [KAIST, Daejeon (Korea, Republic of)

2016-10-15

This paper presents a photonuclear transmutation method using laser Compton scattering (LCS) gamma-ray beam. Potential production rate (reaction rate) of 99Mo using the photonuclear (γ,n) reaction is evaluated. Rigorous optimization of the LCS spectrum has also been performed to maximize production of the 99Mo. Cyclotron proton accelerators are used worldwide to produce many short-living medical isotopes. However, few are capable of producing Mo-99 and none are suitable for producing more than a small fraction of the required amounts. More than 90% of the world's demand of 99Mo is sourced from five nuclear reactors. Two of these reactors have already been decommissioned and the rest are more than 45 years old. Relatively short half-life of the parent 99Mo requires continuous re-supply to meet the requirements of medical industry. Therefore, there is an urgent need to produce the 99Mo and 99mTc isotopes by alternative ways. One such alternative is giant dipole resonance (GDR) based photonuclear transmutation of 100Mo to 99Mo. For 99Mo production with the LCS photons using GDR-based (γ,n) reaction, the gamma-ray energy should be around 15 MeV. This study indicates that optimization of LCS spectrum by varying the electron and laser energies within practical limits can enhance the transmutation of Mo-100 to M-99 quite significantly. It has been found that irradiation time should be rather short, e.g., less than 6 hours, to maximize the weekly production of Mo-99 in the GDR-based Mo-99 production facility using the LCS photons. The analysis shows that production of 99Mo using a high-performance LCS facility offers a potentially-promising alternative for the production of 99mTc.

Overview of EU research activities in transmutation and innovative reactor systems within the Euratom framework programmes

International Nuclear Information System (INIS)

Bhatnagar, V.

2009-01-01

European Community (EC) (currently 27 Member States) shared-cost research has been organised in Framework Programmes (FP) of durations of 4 - 5 years since 1984. The 6th European Atomic Energy Community (EURATOM) Framework Programme (2002 - 06) and the current 7th FP (2007 - 11) have been allocated a fission research budget respectively of 209 and 287 Million Euro from the EC. There are 10 projects (total budget 70 M Euro, EC contribution 38 M Euro) in all aspects of transmutation ranging from road-mapping exercise to large integrated projects on accelerator driven systems, lead-cooled fast critical systems for waste transmutation, technology, fuel, accelerator facilities for nuclear data etc. In Innovative Reactor concepts, there are about half-a-dozen projects (total budget 30 M Euro, EC contribution 16 M Euro) including High Temperature Reactors, Gas-cooled Fast reactors, road-mapping exercise on sodium fast reactors etc. The main research and training activities in FP7 are: management of radioactive waste, reactor systems, radiation protection, infrastructures, human resources and mobility and training. In the two call for proposals (2007 and 2008) in FP7, 8 projects have been accepted in transmutation and innovative reactor concepts (total budget 53 M Euro, EC contribution 32 M Euro). These research projects cover activities ranging from materials, fuels, treatment of irradiated graphite waste, European sodium fast reactor to the establishment of a Central Design Team of a fast-spectrum transmutation device in Europe. The third call for proposals is underway requesting proposals on nuclear data, thermal hydraulics, gas and lead-cooled fast reactor systems with a total EC budget of 20 M Euro. International collaboration is an important element of the EU research policy. This overview paper will present elements of the strategy of EURATOM research and training in waste management including accelerator driven transmutation systems and Innovative reactor concepts

A Study on thermal-hydraulic characteristics of the coolant materials for the transmutation reactor

Energy Technology Data Exchange (ETDEWEB)

Chung, Chang Hyun; You, Young Woo; Cho, Jae Seon; Kim, Ju Youl; Kim, Do Hyoung; Kim, Yoon Ik; Yang, Hui Chang [Seoul National University, Taejon (Korea)

1998-03-01

The objective of this study is to provide the direction of transmutation reactor design in terms of thermal hydraulics especially through the analysis of thermal hydraulic characteristics of various candidate materials for the transmutation reactor coolant. In this study, the characteristics of coolant materials used in current nuclear power plants and candidate materials for transmutation reactor are analyzed and compared. To evaluate the thermal hydraulic characteristics, the preliminary thermal-hydraulic calculation is performed for the candidate coolant materials of transmutation reactor. An analysis of thermal-hydraulic characteristics of transmutation reactor. An analysis of thermal-hydraulic characteristics of Sodium, Lead, Lead-Bismuth, and Lead-Lithium among the liquid metals considered as the coolant of transmutation reactor is performed by using computational fluid dynamics code FLUENT, and SIMPLER algorithm. (author). 50 refs., 40 figs., 30 tabs.

Resolving and quantifying overlapped chromatographic bands by transmutation

Science.gov (United States)

Malinowski

2000-09-15

A new chemometric technique called "transmutation" is developed for the purpose of sharpening overlapped chromatographic bands in order to quantify the components. The "transmutation function" is created from the chromatogram of the pure component of interest, obtained from the same instrument, operating under the same experimental conditions used to record the unresolved chromatogram of the sample mixture. The method is used to quantify mixtures containing toluene, ethylbenzene, m-xylene, naphthalene, and biphenyl from unresolved chromatograms previously reported. The results are compared to those obtained using window factor analysis, rank annihilation factor analysis, and matrix regression analysis. Unlike the latter methods, the transmutation method is not restricted to two-dimensional arrays of data, such as those obtained from HPLC/DAD, but is also applicable to chromatograms obtained from single detector experiments. Limitations of the method are discussed.

On fusion driven systems (FDS) for transmutation

Energy Technology Data Exchange (ETDEWEB)

Aagren, O (Uppsala Univ., Aangstroem laboratory, div. of electricity, Uppsala (Sweden)); Moiseenko, V.E. (Inst. of Plasma Physics, National Science Center, Kharkov Inst. of Physics and Technology, Kharkov (Ukraine)); Noack, K. (Forschungszentrum Dresden-Rossendorf (Germany))

2008-10-15

This report gives a brief description of ongoing activities on fusion driven systems (FDS) for transmutation of the long-lived radioactive isotopes in the spent nuclear waste from fission reactors. Driven subcritical systems appears to be the only option for efficient minor actinide burning. Driven systems offer a possibility to increase reactor safety margins. A comparatively simple fusion device could be sufficient for a fusion-fission machine, and transmutation may become the first industrial application of fusion. Some alternative schemes to create strong fusion neutron fluxes are presented

On fusion driven systems (FDS) for transmutation

International Nuclear Information System (INIS)

Aagren, O; Moiseenko, V.E.; Noack, K.

2008-10-01

This report gives a brief description of ongoing activities on fusion driven systems (FDS) for transmutation of the long-lived radioactive isotopes in the spent nuclear waste from fission reactors. Driven subcritical systems appears to be the only option for efficient minor actinide burning. Driven systems offer a possibility to increase reactor safety margins. A comparatively simple fusion device could be sufficient for a fusion-fission machine, and transmutation may become the first industrial application of fusion. Some alternative schemes to create strong fusion neutron fluxes are presented

Evaluation on transmutation performance of minor actinides with high-flux BWR

International Nuclear Information System (INIS)

Setiawan, M.B.; Kitamoto, A.; Taniguchi, A.

2001-01-01

The performance of high-flux BWR (HFBWR) for burning and/or transmutation (B/T) treatment of minor actinides (MA) and long-lived fission products (LLFP) was discussed herein for estimating an advanced waste disposal with partitioning and transmutation (P and T). The concept of high-flux B/T reactor was based on a current 33 GWt-BWR, to transmute the mass of long-lived transuranium (TRU) to short-lived fission products (SLFP). The nuclide selected for B/T treatment was MA (Np-237, Am-241, and Am-243) included in the discharged fuel of LWR. The performance of B/T treatment of MA was evaluated by a new function, i.e. [F/T ratio], defined by the ratio of the fission rate to the transmutation rate in the core, at an arbitrary burn-up, due to all MA nuclides. According to the results, HFBWR could burn and/or transmute MA nuclides with higher fission rate than BWR, but the fission rate did not increase proportionally to the flux increment, due to the higher rate of neutron adsorption. The higher B/T fraction of MA would result in the higher B/T capacity, and will reduce the units of HFBWR needed for the treatment of a constant mass of MA. In addition, HFBWR had a merit of higher mass transmutation compared to the reference BWR, under the same mass loading of MA

Transmutation of 126Sn in spallation targets of accelerator-driven systems

International Nuclear Information System (INIS)

Han, Chi Young; Saito, Masaki; Sagara, Hiroshi

2009-01-01

The practical feasibility of 126 Sn transmutation in spallation targets of accelerator-driven systems was evaluated from the viewpoints of accumulation of radioactive spallation products and neutron production as well as transmutation amount of 126 Sn. A cylindrical liquid 126 Sn target whose length depends on proton beam energy was described, based on a Pb-Bi target design of accelerator-driven system being developed in JAEA. A proton beam of 1.5 GeV-20 mA was estimated to give the transmutation rate of 126 Sn 6.4 kg/yr, which corresponds to the amount of 126 Sn annually discharged in 27 LWRs of 1 GWt and 33 GWd/THM. The equilibrium radioactivity of spallation products would reach 9% of that of 126 Sn transmuted in the spallation target, and the equilibrium toxicity would be just 3%. Some parametric analyses showed that the effective half-life of 126 Sn could be reduced through a proper reduction of the target size. The 126 Sn target was calculated to produce 40 neutrons per proton of 1.5 GeV and give a neutron spectrum very similar to that of the reference Pb-Bi target. As a result, the transmutation of 126 Sn in the spallation target has a high feasibility in terms of better transmutation performance and comparable target performance. (author)

The Molten Salt Fast Reactor as Highly Efficient Transmutation System

International Nuclear Information System (INIS)

Merk, B.; Rohde, U.; Scholl, S.

2013-01-01

Conclusion and future steps: • MSFR offers very attractive features for efficient transmutation; • significant advantages due to liquid fuel and online refuelling and reprocessing; • significant developments are required on the way to application; • system is very promising for transmutation; • development of a safety approach for liquid fuel reactors (RSWG); • investigation of possibilities to solve the “last transmuter” problem (ICAPP2013) – as future for countries envisaging nuclear phase out or no transition to fast reactor fleet for energy production; • establishing of a strong group “MSFR for transmutation”; • development of a transmutation optimized design

Transmutation of fission products in reactors and accelerator-driven systems

International Nuclear Information System (INIS)

Janssen, A.J.

1994-01-01

Energy flows and mass flows in several scenarios are considered. Economical and safety aspects of the transmutation scenarios are compared. It is difficult to find a sound motivation for the transmutation of fission products with accelerator-driven systems. If there would be any hesitation in transmuting fission products in nuclear reactors, there would be an even stronger hesitation to use accelerator-driven systems, mainly because of their lower energy efficiency and their poor cost effectiveness. The use of accelerator-driven systems could become a 'meaningful' option only if nuclear energy would be banished completely. (orig./HP)

Role of accelerators in the Czech national transmuter project

International Nuclear Information System (INIS)

Bem, P.; Kugler, A.

1999-01-01

The problem of spent nuclear fuel from the so far operated PWRs has become a crucial issue in the Czech Republic. The first attempts to solve this problem by a final deposit of spent fuel into a suitable geological formation have been shown not to be fully acceptable. Therefore, the revival of nuclear transmutation technology application for nuclear incineration of nuclear waste and spent fuel in particular was welcomed. A realistic national project started to be developed in 1996. The four major nuclear research institutions of the country formed a consortium focused on an adoption of the world-wide experience and a development of a national project of a transmutation technology (experimental transmuter LA-0) or an efficient participation in the international effort in that field. Because the LA-0 transmuter concept of subcritical reactor with liquid fuel based on molten fluorides driven by an external neutron source has been adopted, the R and D effort has been focused on three regions. The first is devoted to the problem of a suitable neutron source, the second to a pre-conceptual design of a blanket for burning of actinides contained in spent fuel from PWRs. The third region is devoted to the utilisation of the experience from a specific field of dry (fluorine) reprocessing of spent fuel and a preparation of liquid fuel in the form of molten fluorides for the transmuter LA-0. (R.P.)

ZZ REAC-2, Nuclide Activation and Transmutation

International Nuclear Information System (INIS)

Mann, F.M.

2002-01-01

1 - Description of program or function: Flux library: Format: special format, Number Of Groups: 63 group fluxes, Nuclides: H, He, Li, Be, B, C, N, O, F, Ne, Na, Mg, Al, Si, P, S, Cl, Ar, K, Ca, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, As, Se, Br, Kr, Rb, Sr, Y, Zr, Nb, Mo, Tc, Ru, Rh, Pd, Ag, Cd, In, Sn, Sb, Te, I, Xe, Cs, Ba, La, Ce, Pr, Nd, Pm, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Hf, Ta, W, Re, Os, Ir, Pt, Au, Hg, Tl, Pb, Bi, Po. Origin: Fred Mann (Westinghouse, Hanford). Cross Section library: Format: special format, Number Of Groups: 63 group cross section, Nuclides: H, He, Li, Be, B, C, N, O, F, Ne, Na, Mg, Al, Si, P, S, Cl, Ar, K, Ca, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, As, Se, Br, Kr, Rb, Sr, Y, Zr, Nb, Mo, Tc, Ru, Rh, Pd, Ag, Cd, In, Sn, Sb, Te, I, Xe, Cs, Ba, La, Ce, Pr, Nd, Pm, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Hf, Ta, W, Re, Os, Ir, Pt, Au, Hg, Tl, Pb, Bi, Po. Origin: Fred Mann (Westinghouse, Hanford). Decay Data library: Format: special format, Nuclides: H, He, Li, Be, B, C, N, O, F, Ne, Na, Mg, Al, Si, P, S, Cl, Ar, K, Ca, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, As, Se, Br, Kr, Rb, Sr, Y, Zr, Nb, Mo, Tc, Ru, Rh, Pd, Ag, Cd, In, Sn, Sb, Te, I, Xe, Cs, Ba, La, Ce, Pr, Nd, Pm, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Hf, Ta, W, Re, Os, Ir, Pt, Au, Hg, Tl, Pb, Bi, Po. Origin: Fred Mann (Westinghouse, Hanford). REAC2 calculates the change in composition of materials in a radiation field and related activation quantities. It is best suited to problems where many variables (e.g. materials, facilities or locations within facilities, power histories) are to be investigated. Where very accurate results are needed, the user must access the accuracy of the cross section base (e.g. source, flux weighting) as in the use of any neutronics code. REAC2 consists of three programs - SREAC, SLSTCOM, and SLIB. SREAC calculates the transmutation of nuclides in a radiation field. SLSTCOM reads the output file produced by SREAC and produces listings of

MYRRHA. An innovative and unique research facility

Energy Technology Data Exchange (ETDEWEB)

Fernandez, Rafaeol; Neerdael, Bernard; Schyns, Marc; Dyck, Steven Van; Michiels, Sidney; Ait Abderrahim, Hamid, E-mail: myrrha@sckcen.be [Belgian Nuclear Research Centre (SCK-CEN), Mol (Belgium)

2012-03-15

The MYRRHA project started in 1998 by SCK{center_dot}CEN in collaboration with Ion Beam Applications (IBA, Louvain-la-Neuve), as an upgrade of the ADONIS project. MYRRHA is designed as a multi-purpose irradiation facility in order to support research programmes on fission and fusion reactor structural materials and nuclear fuel development. Applications of these are found in Accelerator Driven Systems (ADS) systems and in present generation as well as in next generation critical reactors. The first objective of MYRRHA however, will be to demonstrate on one hand the ADS concept at a reasonable power level and on the other hand the technological feasibility of transmutation of Minor Actinides (MA) and Long-Lived Fission Products (LLFP) arising from the reprocessing of radioactive waste. MYRRHA will also help the development of the Pb-alloys technology needed for the LFR (Lead Fast Reactor) Gen.IV concept. Transmutation of MA can be completed in an efficient way in fast neutron spectrum facilities. Both critical reactors and sub-critical ADS are potential candidates as dedicated transmutation systems. However, critical reactors, heavily loaded with fuel containing large amounts of MA, pose safety problems caused by unfavourable reactivity coefficients due to the little delayed neutron fraction. A sub-critical ADS operates in a flexible and safe manner even with a core loading containing a high amount of MA leading to achieve a high efficient transmutation. Thus, the sub-criticality is not a virtue but rather a necessity for an efficient and economical burning of the MA. Besides the reduction of the HLW burden, the MYRRHA project will serve the purpose of developing the lead alloys technology as a reactor coolant that can be used in one of the Generation IV reactor concepts namely the Lead Fast Reactor (LFR). Although carrying out the MYRRHA project will lead to the demonstration of the efficient and safe transmutation of MA in ADS systems as the ultimate goal the

System and safety studies of accelerator driven transmutation systems. Annual report 1997

International Nuclear Information System (INIS)

Wallenius, J.; Carlsson, Johan; Gudowski, W.

1997-12-01

In November 1996, SKB started financing of the project ''System and safety studies of accelerator driven transmutation systems and development of a spallation target''. The aim of the project was stated as: 1) Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. 2) Build up of competence regarding issues related to spallation targets development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration-experiment. In the present report, activities within the framework of the project performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1997, are accounted for

System and safety studies of accelerator driven transmutation systems. Annual report 1997

Energy Technology Data Exchange (ETDEWEB)

Wallenius, J.; Carlsson, Johan; Gudowski, W. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

1997-12-01

In November 1996, SKB started financing of the project ``System and safety studies of accelerator driven transmutation systems and development of a spallation target``. The aim of the project was stated as: 1) Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. 2) Build up of competence regarding issues related to spallation targets development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration-experiment. In the present report, activities within the framework of the project performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1997, are accounted for. 13 refs, 6 figs.

System and safety studies of accelerator driven transmutation systems. Annual report 1999

International Nuclear Information System (INIS)

Gudowski, Waclaw; Wallenius, Jan; Eriksson, Marcus; Carlsson, Johan; Seltborg, Per; Tucek, Kamil

2000-05-01

In 1996, SKB commenced funding of the project 'System and safety studies of accelerator driven transmutation systems and development of a spallation target'. The aim of the project was stated as: Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. Build up of competence regarding issues related to spallation targets, development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation. target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration experiment. In the present report, activities within and related to the framework of the project, performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1999, are accounted for

System and safety studies of accelerator driven transmutation systems. Annual report 1999

Energy Technology Data Exchange (ETDEWEB)

Gudowski, Waclaw; Wallenius, Jan; Eriksson, Marcus; Carlsson, Johan; Seltborg, Per; Tucek, Kamil [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

2000-05-01

In 1996, SKB commenced funding of the project 'System and safety studies of accelerator driven transmutation systems and development of a spallation target'. The aim of the project was stated as: Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. Build up of competence regarding issues related to spallation targets, development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation. target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration experiment. In the present report, activities within and related to the framework of the project, performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1999, are accounted for.

Chemico-technological support of transmutation objectives: Solid, molten salt and liquid blanket

Energy Technology Data Exchange (ETDEWEB)

Volk, V.I.; Zakharkin, B.S.; Vakhrushin, A.Y. [VNIINM, Moscow (Russian Federation)

1995-10-01

Chemical and technological provision for the transmutation process, independantly on the scheme of its conduction, includes: fuel composition separation for fractions of components, subjected to annihilation; their transition into chemical form, in which they are present in the reactor; discharge and return into the form, convenient for chemical reprocessing, providing for the transmutation products separation from the components being transmutated and transferring of short-lived isotopes into the form of their temporary storage. The authors discuss different chemical processes which can be used in these steps to either improve efficiency or minimize additional waste generation and expense associated with decontamination. They consider processes involving molten salts for circulation of wastes thru transmutation steps, and possible advantages in extraction processes.

Transmutation Fuel Campaign Description and Status

International Nuclear Information System (INIS)

Jon Carmack; Kemal O. Pasamehmetoglu

2008-01-01

This report contains a technical summary package in response to a Level 2 milestone in the transmutation fuel campaign (TFC) management work-package calling for input to the Secretarial decision. At present, the form of the Secretarial decision package is not fully defined, and it is not clear exactly what will be required from the TFC as a final input. However, it is anticipated that a series of technical and programmatic documents will need to be provided in support of a wider encompassing document on GNEP technology development activities. The TFC technical leadership team provides this report as initial input to the secretarial decision package which is being developed by the Technical Integration Office (TIO) in support of Secretarial decision. This report contains a summary of the TFC execution plan with a work breakdown structure, high level schedule, major milestones, and summary description of critical activities in support of campaign objectives. Supporting documents referenced in this report but provided under separate cover include: (1) An updated review of the state-of-the art for transmutation fuel development activities considering national as well as international fuel research and development testing activities. (2) A definition of the Technology Readiness Level (TRL) used to systematically define and execute the transmutation fuel development activities

Accelerator for nuclear transmutation

International Nuclear Information System (INIS)

Schapira, J.P.

1984-01-01

A review on nuclear transmutation of radioactive wastes using particle accelerators is given. Technical feasibility, nuclear data, costs of various projects are discussed. It appears that one high energy accelerator (1500 MeV, 300 mA proton) could probably handle the amount of actinides generated by the actual French nuclear program [fr

Effect of activation cross section uncertainties in transmutation analysis of realistic low-activation steels for IFMIF

Energy Technology Data Exchange (ETDEWEB)

Cabellos, O.; Garcya-Herranz, N.; Sanz, J. [Institute of Nuclear Fusion, UPM, Madrid (Spain); Cabellos, O.; Garcya-Herranz, N.; Fernandez, P.; Fernandez, B. [Dept. of Nuclear Engineering, UPM, Madrid (Spain); Sanz, J. [Dept. of Power Engineering, UNED, Madrid (Spain); Reyes, S. [Safety, Environment and Health Group, ITER Joint Work Site, Cadarache Center (France)

2008-07-01

We address uncertainty analysis to draw conclusions on the reliability of the activation calculation in the International Fusion Materials Irradiation Facility (IFMIF) under the potential impact of activation cross section uncertainties. The Monte Carlo methodology implemented in ACAB code gives the uncertainty estimates due to the synergetic/global effect of the complete set of cross section uncertainties. An element-by-element analysis has been demonstrated as a helpful tool to easily analyse the transmutation performance of irradiated materials.The uncertainty analysis results showed that for times over about 24 h the relative error in the contact dose rate can be as large as 23 per cent. We have calculated the effect of cross section uncertainties in the IFMIF activation of all different elements. For EUROFER, uncertainties in H and He elements are 7.3% and 5.6%, respectively. We have found significant uncertainties in the transmutation response for C, P and Nb.

Analysis of the Gas Core Actinide Transmutation Reactor (GCATR)

Science.gov (United States)

Clement, J. D.; Rust, J. H.

1977-01-01

Design power plant studies were carried out for two applications of the plasma core reactor: (1) As a breeder reactor, (2) As a reactor able to transmute actinides effectively. In addition to the above applications the reactor produced electrical power with a high efficiency. A reactor subsystem was designed for each of the two applications. For the breeder reactor, neutronics calculations were carried out for a U-233 plasma core with a molten salt breeding blanket. A reactor was designed with a low critical mass (less than a few hundred kilograms U-233) and a breeding ratio of 1.01. The plasma core actinide transmutation reactor was designed to transmute the nuclear waste from conventional LWR's. The spent fuel is reprocessed during which 100% of Np, Am, Cm, and higher actinides are separated from the other components. These actinides are then manufactured as oxides into zirconium clad fuel rods and charged as fuel assemblies in the reflector region of the plasma core actinide transmutation reactor. In the equilibrium cycle, about 7% of the actinides are directly fissioned away, while about 31% are removed by reprocessing.

Spallation neutron source target design for radioactive waste transmutation

International Nuclear Information System (INIS)

Beard, C.A.

1992-01-01

The disposal of high-level radioactive waste has long been one of the most serious problems facing the nuclear industry. Transmutation of this waste through particle bombardment has been suggested numerous times as a possible method of enhancing the waste management process. Due to advances in accelerator technology, the feasibility of an accelerator based transmutation system has increased enough to allow serious investigation of this process. Therefore, in pursuit of this goal, an accelerator target was designed for use in an accelerator based transmutation system. The target design consists of an array of tantalum rods, cooled by liquid sodium, which are arranged in a cylindrical configuration 40 cm in diameter and 125 cm in height. Tantalum was chosen as the target material over tungsten, lead, bismuth, and a lead-bismuth alloy (55 w/o bismuth) due to a large neutron yield, low activation, low chemical toxicity, and the fact that it does not produce significant amounts of long-lived isotopes through spallation or activation. The target yields a neutron source of 29.7 neutrons/proton when exposed to a 1600 MeV proton beam, and is suitable for use with both thermal or fast spectrum transmutation systems

Fuels and targets for the transmutation of high activity long lived radioactive wastes

International Nuclear Information System (INIS)

Pillon, S.; Warin, D.

2010-01-01

The authors present and comment the different strategies which can be adopted to transmute minor actinides (concerned reactors, in fast breeder reactors, in accelerator driven systems or ADS), and the chemical composition of transmutation fuels (actinide compounds, inert matrices, fuels and targets). They describe the behaviour of refractory ceramic fuels during their service life under irradiation with their different damage origins (neutrons, fission by-products, alpha particles), the fabrication of transmutation fuels and targets through different processes (metallurgical, co-precipitate, sol-gel, wax, infiltration of radioactive materials, VIPAC/SPHEREPAC) and the reprocessing or recycling of these transmutation fuels and targets

Transmutation of actinide 237Np with a fusion reactor and a hybrid reactor

International Nuclear Information System (INIS)

Feng, K.M.; Huang, J.H.

1994-01-01

The use of fusion reactors to transmute fission reactor wastes to stable species is an attractive concept. In this paper, the feasibility of transmutation of the long-lived actinide radioactive waste Np-237 with a fusion reactor and a hybrid reactor has been investigated. A new waste management concept of burning HLW (High Level Waste), utilizing released energy and converting Np-237 into fissile fuel Pu-239 through transmutation has been adopted. The detailed neutronics and depletion calculation of waste inventories was carried out with a modified version of one-dimensional neutron transport and burnup calculation code system BISON1.5 in this study. The transmutation rate of Np with relationship to neutron wall loading, Pu and Np with relationship to neutron wall load, Pu and Np concentration in the transmutation zone have been explored as well as relevant results are also given

Role of (n,2n) reactions in transmutation of long-lived fission products

Energy Technology Data Exchange (ETDEWEB)

Apse, V. A.; Kulikov, G. G., E-mail: ggkulikov@mephi.ru; Kulikov, E. G. [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute) (Russian Federation)

2016-12-15

The conditions under which (n,γ) and (n,2n) reactions can help or hinder each other in neutron transmutation of long-lived fission products (LLFPs) are considered. Isotopic and elemental transmutation for the main long-lived fission products, {sup 79}Se, {sup 93}Zr, {sup 99}Tc, {sup 107}Pd, {sup 126}Sn, {sup 129}I, and {sup 135}Cs, are considered. The effect of (n,2n) reactions on the equilibrium amount of nuclei of the transmuted isotope and the neutron consumption required for the isotope processing is estimated. The aim of the study is to estimate the influence of (n,2n) reactions on efficiency of neutron LLFP transmutation. The code TIME26 and the libraries of evaluated nuclear data ABBN-93, JEF-PC, and JANIS system are applied. The following results are obtained: (1) The effect of (n,2n) reactions on the minimum number of neutrons required for transmutation and the equilibrium amount of LLFP nuclei is estimated. (2) It is demonstrated that, for three LLFP isotopes ({sup 126}Sn, {sup 129}I, and {sup 135}Cs), (n,γ) and (n,2n) reactions are partners facilitating neutron transmutation. The strongest effect of (n,2n) reaction is found for {sup 126}Sn transmutation (reduction of the neutron consumption by 49% and the equilibrium amount of nuclei by 19%).

Transmutation research and fuel cycle (report on discussion at Research Reactor Institute, Kyoto University)

International Nuclear Information System (INIS)

Yamana, Hajimu

1999-01-01

A symposium was held on a topic of 'Transmutation Research' on Dec. 21 and 22, 1999 at Research Reactor Institute, Kyoto University. This meeting was held as a joint-meeting of KUR's specialist meeting and Tokyo University's activity supported by the Grant-in-Aid for Scientific Research of Ministry of Education, Sport and Culture of Japan. This paper describes the overview of the discussions of this joint-meeting, and interprets their significance. Major themes discussed are, needed discussions on the transmutation research, policy and concepts of the organizations doing transmutation researches, a view from university side, transmutation researches in the oversea countries, opinions from various standpoints of the nuclear fuel cycle, conclusive discussions. 'the meanings of the transmutation research should be discussed together with the geological disposal and fast reactor system', 'transmutation may be a cooperative option for the disposal, thus, they should not be in a independent relation', and Balance evaluation will be needed' are the examples of the conclusive remarks of this meeting. (author)

Calculations of different transmutation concepts. An international benchmark exercise

International Nuclear Information System (INIS)

2000-01-01

In April 1996, the NEA Nuclear Science Committee (NSC) Expert Group on Physics Aspects of Different Transmutation Concepts launched a benchmark exercise to compare different transmutation concepts based on pressurised water reactors (PWRs), fast reactors, and an accelerator-driven system. The aim was to investigate the physics of complex fuel cycles involving reprocessing of spent PWR reactor fuel and its subsequent reuse in different reactor types. The objective was also to compare the calculated activities for individual isotopes as a function of time for different plutonium and minor actinide transmutation scenarios in different reactor systems. This report gives the analysis of results of the 15 solutions provided by the participants: six for the PWRs, six for the fast reactor and three for the accelerator case. Various computer codes and nuclear data libraries were applied. (author)

Multiple tier fuel cycle studies for waste transmutation

International Nuclear Information System (INIS)

Hill, R.N.; Taiwo, T.A.; Stillman, J.A.; Graziano, D.J.; Bennett, D.R.; Trellue, H.; Todosow, M.; Halsey, W.G.; Baxter, A.

2002-01-01

As part of the U.S. Department of Energy Advanced Accelerator Applications Program, a systems study was conducted to evaluate the transmutation performance of advanced fuel cycle strategies. Three primary fuel cycle strategies were evaluated: dual-tier systems with plutonium separation, dual-tier systems without plutonium separation, and single-tier systems without plutonium separation. For each case, the system mass flow and TRU consumption were evaluated in detail. Furthermore, the loss of materials in fuel processing was tracked including the generation of new waste streams. Based on these results, the system performance was evaluated with respect to several key transmutation parameters including TRU inventory reduction, radiotoxicity, and support ratio. The importance of clean fuel processing (∼0.1% losses) and inclusion of a final tier fast spectrum system are demonstrated. With these two features, all scenarios capably reduce the TRU and plutonium waste content, significantly reducing the radiotoxicity; however, a significant infrastructure (at least 1/10 the total nuclear capacity) is required for the dedicated transmutation system

Transmutation Studies of Radioactive Nuclides

Czech Academy of Sciences Publication Activity Database

Adam, Jindřich

2007-01-01

Roč. 34, č. 1 (2007), s. 125-150 ISSN 1310-0157 R&D Projects: GA MŠk 1P04LA213 Institutional research plan: CEZ:AV0Z10480505 Keywords : transmutation Subject RIV: BG - Nuclear, Atomic and Molecular Physics , Colliders

Neutron transmutation doping of polycrystalline silicon

International Nuclear Information System (INIS)

Cleland, J.W.; Westbrook, R.D.; Wood, R.F.; Young, R.T.

1976-04-01

Chemical vapor deposition (CVD) of doped silane has been used by others to deposit a polycrytalline silicon film (polysil) on metal or graphite substrates, but dopant migration to grain boundaries during deposition apparently prohibits attaining a uniform or desired dopant concentration. In contrast, we have used neutron transmutation doping to introduce a uniform phosphorus dopant concentration in commercially available undoped CVD polysil at doping concentrations greater than or equal to 2 x 10 15 cm -3 . Radiation damage annealing to 800 0 C did not indicate dopant migration. Carrier mobility increased with doping concentration and the minority carrier lifetime (MCL) appears to be comparable to that of neutron transmutation doped (NTD) single crystal Si. Application of this technique to photovoltaic solar cell fabrication is discussed

Application of gaseous core reactors for transmutation of nuclear waste

Science.gov (United States)

Schnitzler, B. G.; Paternoster, R. R.; Schneider, R. T.

1976-01-01

An acceptable management scheme for high-level radioactive waste is vital to the nuclear industry. The hazard potential of the trans-uranic actinides and of key fission products is high due to their nuclear activity and/or chemical toxicity. Of particular concern are the very long-lived nuclides whose hazard potential remains high for hundreds of thousands of years. Neutron induced transmutation offers a promising technique for the treatment of problem wastes. Transmutation is unique as a waste management scheme in that it offers the potential for "destruction" of the hazardous nuclides by conversion to non-hazardous or more manageable nuclides. The transmutation potential of a thermal spectrum uranium hexafluoride fueled cavity reactor was examined. Initial studies focused on a heavy water moderated cavity reactor fueled with 5% enriched U-235-F6 and operating with an average thermal flux of 6 times 10 to the 14th power neutrons/sq cm-sec. The isotopes considered for transmutation were I-129, Am-241, Am-242m, Am-243, Cm-243, Cm-244, Cm-245, and Cm-246.

Transmutation: a decade of revival issues, relevant experiments and perspectives

International Nuclear Information System (INIS)

Salvatores, M.

2001-01-01

For more than a decade, transmutation studies have been again a topic of wide interest and have triggered numerous international activities, like bilateral/multilateral collaborations, information exchanges, state-of-the-art reports, conferences, but also some co-ordinated programmes and experiments. It is legitimate to ask at this point, whether transmutation studies are still 'fashionable' and why; what is known, what has been done and what should be done. Since the motivations of national programmes are often different, due to a different context, we will take for granted that transmutation is generally seen as an option for the back-end of the fuel cycle in order to reduce the burden of potential geological storages of radioactive wastes (whatever their nature). Finally, we also acknowledge the fact that some highly respected scientists have at several occasions during this decade expressed their doubts about the value of the transmutation option. A typical example is the position expressed by Pigford and Rasmussen, reporting the results of a study for the US National Research Council. (author)

JAERI R & D on accelerator-based transmutation under OMEGA program

Energy Technology Data Exchange (ETDEWEB)

Takizuka, T.; Nishida, T.; Mizumoto, M. [Japan Atomic Energy Research Institute, Ibaraki-ken (Japan)] [and others

1995-10-01

The overview of the Japanese long-term research and development program on nuclide partitioning and transmutation, called {open_quotes}OMEGA,{close_quotes} is presented. Under this national program, major R&D activities are being carried out at JAERI, PNC, and CRIEPI. Accelerator-based transmutation study at JAERI is focused on a dedicated transmutor with a subcritical actinide-fueled subcritical core coupled with a spallation target driven by a high intensity proton accelerator. Two types of system concept, solid system and molten-salt system, are discussed. The solid system consists of sodium-cooled tungsten target and metallic actinide fuel. The molten-salt system is fueled with molten actinide chloride that acts also as a target material. The proposed plant transmutes about 250 kg of minor actinide per year, and generates enough electricity to power its own accelerator. JAERI is proposing the development of an intense proton linear accelerator ETA with 1.5 GeV-10 mA beam for engineering tests of accelerator-based transmutation. Recent achievements in the accelerator development are described.

Requirements for an evaluated nuclear data file for accelerator-based transmutation

International Nuclear Information System (INIS)

Koning, A.J.

1993-06-01

The importance of intermediate-energy nuclear data files as part of a global calculation scheme for accelerator-based transmutation of radioactive waste systems (for instance with an accelerator-driven subcritical reactor) is discussed. A proposal for three intermediate-energy data libraries for incident neutrons and protons is presented: - a data library from 0 to about 100 MeV (first priority), - a reference data library from 20 to 1500 MeV, - an activation/transmutation library from 0 to about 100 MeV. Furthermore, the proposed ENDF-6 structure of each library is given. The data needs for accelerator-based transmutation are translated in terms of the aforementioned intermediate-energy data libraries. This could be a starting point for an ''International Evaluated Nuclear Data File for Transmutation''. This library could also be of interest for other applications in science and technology. Finally, some conclusions and recommendations concerning future evaluation work are given. (orig.)

Comparative Study of the Reactor Burner Efficiency for Transmutation of Minor Actinides

Energy Technology Data Exchange (ETDEWEB)

Gulevich, A.; Zemskov, E. [Institute of Physics and Power Engineering, Bondarenko sq. 1, Obninsk, Kaluga region, 249020 (Russian Federation); Degtyarev, A.; Kalugin, A.; Ponomarev, L. [Russian Research Center ' Kurchatov Institute' , Kurchatov sq. 1, Moscow, 123182 (Russian Federation); Konev, V.; Seliverstov, V. [Institute of Theoretical and Experimental Physics, ul. B. Cheremushinskaya 25, Moscow, 117259 (Russian Federation)

2009-06-15

Transmutation of minor actinides (MA) in the closed nuclear fuel cycle (NFC) is a one of the most important problem for future nuclear energetic. There are several approaches for MA transmutation but there are no common criteria for the comparison of their efficiency. In paper [1] we turned out the attention to the importance of taking into account the duration of the closed NFC in addition to a usual criterion of the neutron economy. In accordance with these criteria the transmutation efficiency are compared of two fast reactors (sodium and lead cooled) and three types of ADS-burners: LBE-cooled reactors (fast neutron spectrum), molten-salt reactor (intermediate spectrum) and heavy water reactor (thermal spectrum). It is shown that the time of transmutation of loaded MA in the closed nuclear fuel cycle is more than 50 years. References: A. Gulevich, A. Kalugin, L. Ponomarev, V. Seliverstov, M. Seregin, 'Comparative Study of ADS for Minor Actinides Transmutation', Progress in Nuclear Energy, 50, March-August, p. 358, 2008. (authors)

Researches on the management of high activity and long-lived radioactive wastes. Axis 1 - separation-transmutation; Recherches sur la gestion des dechets radioactifs a haute activite et a vie longue. Axe 1 - separation-transmutation

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-11-15

This document gathers the transparencies of seven presentations given at a technical workshop of the French nuclear energy society (SFEN) about the researches on separation-transmutation of high activity and long-lived radioactive wastes. The presentations deal with: inventory and radiotoxicity of the rad-wastes in concern; industrial experience; experience on chemical separation: molecules and processes; reactors physics and transmutation - reactors for transmutation; fuels and targets; scenarios that include transmutation; environmental impacts of these different scenarios. (J.S.)

Effects of actinide compositional variability in the US spent fuel inventory on partitioning-transmutation systems

International Nuclear Information System (INIS)

Ludwig, S.B.; Michaels, G.E.; Hanson, B.D.

1992-01-01

Partitioning and transmutation (P-T) is an advanced waste management concept by which certain undesirable nuclides in spent fuel are first isolated (partitioned) and later destroyed (transmuted) in a nuclear reactor or other transmutation device. There are wide variabilities in the nuclide composition of spent fuel. This implies that there will also be wide variabilities in the transmutation device feed. As a waste management system, P-T must be able to accept (all) spent fuel. Variability of nuclide composition (i.e., the feed material for transmutation devices) may be important because virtually all transmutation systems propose to configure transuranic (TRU) nuclides recovered from discharged lightwater reactor (LWR) spent fuel in critical or near-critical cores. To date, all transmutation system core analyses assume invariant nuclide concentrations for startup and recycle cores. Using the US Department of Energy's (DOE's) Characteristics Data Base (CDB) and the ORIGEN2 computer code, the current and projected spent fuel discharges until the year 2016 have been categorized according to combinations of fuel burnup, initial enrichment, fuel age (cooling time) and reactor type (boiling-water or pressurized-water reactors). The variability of the infinite multiplication factor (k ∞ ) is calculated for both fast (ALMR) and thermal (accelerator-based) transmuter systems

Transmutation studies in France, R and D programme on fuels and targets

International Nuclear Information System (INIS)

Boidron, M.; Chauvin, N.; Garnier, J.C.; PIllon, S.; Vambenepe, G.

2001-01-01

For the management of high level and long-lived radioactive waste, a large and continuous research and development effort is carried out in France, to provide a wide range of scientific and technical alternatives along three lines, partitioning and transmutation, disposal in deep geological formations and long term interim surface or subsurface storage. For the line one, and in close link with the partitioning studies, research is carried out to evaluate the transmutation potential of long-lived waste in appropriate reactors configurations (scenarios) relying on current technologies as well as innovative reactors. Performed to evaluate the theoretical feasibility of the Pu consumption and waste transmutation from the point of view of the reactor cores physics to reach the equilibrium of the material fluxes (i.e. consumption = production) and of the isotopic compositions of the fuels, these studies insure the 'scientific' part of the transmutation feasibility. For the technological part of the feasibility of waste transmutation in reactors, a large programme on fuel development is underway. This includes solutions based on the advanced concepts for plutonium fuels in PWR and the development of specific fuels and targets for transmutation in fast reactors in the critical or sub-critical state. For the waste transmutation in fast reactors, an important programme has been launched to develop specific fuels and targets with experiments at various stages of preparation in different experimental reactors including Phenix. Composite fuels as well as particle fuels are considered. This programme is presented and recent results concerning the preparation of the experiments, the characterisation of the compounds properties, the thermal and mechanical modelling and the behaviour of U free fuels are given. (author)

Minor actinide transmutation - a waste management option

International Nuclear Information System (INIS)

Koch, L.

1986-01-01

The incentive to recycle minor actinides results from the reduction of the long-term α-radiological risk rather than from a better utilization of the uranium resources. Nevertheless, the gain in generated electricity by minor actinide transmutation in a fast breeder reactor can compensate for the costs of their recovery and make-up into fuel elements. Different recycling options of minor actinides are discussed: transmutation in liquid metal fast breeder reactors (LMFBRs) is possible as long as plutonium is not recycled in light water reactors (LWRs). In this case a minor actinide burner with fuel of different composition has to be introduced. The development of appropriate minor actinide fuels and their properties are described. The irradiation experiments underway or planned are summarized. A review of minor actinide partitioning from the PUREX waste stream is given. From the present constraints of LMFBR technology a reduction of the long-term α-radiological risk by a factor of 200 is deduced relative to that from the direct storage of spent LWR fuel. Though the present accumulation of minor actinides is low, nuclear transmutation may be needed when nuclear energy production has grown. (orig.)

The possible transmutation of radioactive waste from nuclear reactors

International Nuclear Information System (INIS)

Harries, J.R.

1974-01-01

A nuclear reactor power program produces high level and long lived radioactive wastes. The high level activity is associated with fission products, but beyond 400 years the principal waste hazard is from transuranic elements produced in the reactor. Several schemes have been proposed for the transmutation of the problem isotopes into more easily handled isotopes. The neutron flux in a thermal reactor is not high enough to significantly reduce the longer lived fission product isotopes 90 Sr and 132 Gs, but the transuranic elements can be reduced by recycling through power reactors. The limitation on recycling of the transuranic elements is the separation process to remove trace quantities from the waste stream. In fast reactors the transuranic elements are the principal fuel and fast reactor waste contains only half as much 90 Sr as thermal reactors. However, the overall waste hazard is similar to thermal reactors. A sufficiently intense neutron flux for fission product transmutation could perhaps be produced by a spallation reactor driven by a proton linear accelerator or a controlled thermonuclear reactor. However, both concepts are still some years in the future. Transmutation by accelerator sources of protons, electrons of gammas tend to require more energy than neutron transmutation. (author)

Study of minor actinides transmutation in heavy water cooled tight-pitch lattice

International Nuclear Information System (INIS)

Xu Xiaoqin; Shiroya, S.

2002-01-01

Minor actinides inhere long half-life and high toxicity. It is an alternative technical pathway and helpful for reducing environmental impact to incinerate minor actinides in spent fuel of nuclear power plants. Because of its high neutron, γ and β emitting rates and heat generation rate, it is necessary to imply more severe control and shielding techniques in the chemical treatment and fabrication. From economic view-point, it is suitable to transmute minor actinides in concentrated way. A technique for MA transmutation by heavy water cooled tight-pitch lattice system is proposed, and calculated with SRAC95 code system. It is shown that tight-pitch heavy water lattice can transmute MA effectively. The accelerator-driven subcritical system is practical for MA transmutation because of its low fraction of effective delay neutrons

Transmutation of planar media singularities in a conformal cloak.

Science.gov (United States)

Liu, Yichao; Mukhtar, Musawwadah; Ma, Yungui; Ong, C K

2013-11-01

Invisibility cloaking based on optical transformation involves materials singularity at the branch cut points. Many interesting optical devices, such as the Eaton lens, also require planar media index singularities in their implementation. We show a method to transmute two singularities simultaneously into harmless topological defects formed by anisotropic permittivity and permeability tensors. Numerical simulation is performed to verify the functionality of the transmuted conformal cloak consisting of two kissing Maxwell fish eyes.

Impact of Blanket Configuration on the Design of a Fusion-Driven Transmutation Reactor

Directory of Open Access Journals (Sweden)

Bong Guen Hong

2018-02-01

Full Text Available A configuration of a fusion-driven transmutation reactor with a low aspect ratio tokamak-type neutron source was determined in a self-consistent manner by using coupled analysis of tokamak systems and neutron transport. We investigated the impact of blanket configuration on the characteristics of a fusion-driven transmutation reactor. It was shown that by merging the TRU burning blanket and tritium breeding blanket, which uses PbLi as the tritium breeding material and as coolant, effective transmutation is possible. The TRU transmutation capability can be improved with a reduced blanket thickness, and fast fluence at the first wall can be reduced.  Article History: Received: July 10th 2017; Received: Dec 17th 2017; Accepted: February 2nd 2018; Available online How to Cite This Article: Hong, B.G. (2018 Impact of Blanket Configuration on the Design of a Fusion-Driven Transmutation Reactor. International Journal of Renewable Energy Development, 7(1, 65-70. https://doi.org/10.14710/ijred.7.1.65-70

Transmutations: Rejuvenation, Longevity, and Immortality Practices in South and Inner Asia

Directory of Open Access Journals (Sweden)

Dagmar Wujastyk

2017-12-01

Full Text Available Wild and diverse outcomes are associated with transmutational practices: the prolongation of life, the recovery of youth, the cure of diseases, invincibility, immortality, enlightenment, liberation from the cycle of rebirths, and unending bliss. This range of outcomes is linked to specific practices taught in separate traditions and lineages in medical, alchemical, yogic and tantric milieus across South and Inner Asia. These practices can be individual or collective, esoteric or secular, and occur in different places from hospital to village to monastery; they involve transmutations of substances as well as transmutations of the body. Every expression by a particular lineage has a distinguishing articulation. Yet there are also very clear commonalities and interconnections between the traditions’ aims, methods and expected results. In this special issue of HSSA, we examine transmutational practices and their underlying concepts in this wider context of South and Inner Asian culture. How do these practices and ideas connect and cross-fertilise? And conversely, how are they delineated and distinct?

Transmutation of high-level radioactive waste by a charged particle accelerator

International Nuclear Information System (INIS)

Takahashi, Hiroshi.

1993-01-01

Transmutation of minor actinides and fission products using proton accelerators has many advantages over a transmutor operated in a critical condition. The energy required for this transmutation can be reduced by multiplying the spallation neutrons in a subcritical assembly surrounding the spallation target. The authors have studied the relation between the energy requirements and the multiplication factor, k, of the subcritical assembly, while varying the range of several parameters in the spallation target. A slightly subcritical reactor is superior to a reactor with large subcriticality in the context of the energy requirement of a small proton accelerator, the extent of radiation damage, and other safety problems. To transmute the fission products, the transmutor reactor must have a good neutron economy, which can be provided by a transmutor operated by a proton accelerator. The paper discusses the use of minor actinides to improve neutronics characteristics, such as a long fuel burn-up rather than simply transmuting this valuable material

The French partitioning-transmutation programme, assets and prospects

International Nuclear Information System (INIS)

Viala, M.; Salvatores, M.; Mouney, H.

1997-01-01

Partitioning-transmutation studies are covered by the 1991 French law concerning radioactive waste management. The programme is progressing with a dual approach: - What can be done in partitioning-transmutation? At what cost? In what timescale? - How can long-term gains and short-term disadvantages be qualified and quantified? The first approach concerns technical know-how. The studies based on today's technologies are continuing (reactors, fuels and targets, separation of radionuclides by solvents). The second approach involves an assessment activity, based firstly on studies of scenarios. Pertinent assessment criteria must be brought out. (authors)

Evaluation of systems incorporating transmutation for the reduction of the long term toxicity of high-level waste

International Nuclear Information System (INIS)

Davidson, J.W.

1979-01-01

One of the alternative high-level nuclear waste (HLW) management/disposal concepts proposed involves the separation from HLW of the elements with isotopes which dominate the radiotoxicity and the transmutation of these nuclides to shortlived or stable products. The waste management system required for transmutation employs chemical processing of HLW to recover waste nuclides for irradiation with neutrons in a transmutation device. The transmuter periodically requires replenishment of the target nuclides and chemical processing to remove the transmutation products. The waste streams from HLW processing and product recovery together comprise the discharge from the system. An imploding liner fusion reactor (ILFR) is assumed for the transmuter with the waste nuclides dissolved in a molten lead-lithium alloy blanket. The potential transmutation candidates are defined as the elements with toxicities per unit volume (toxicity indexes) in solidified HLW at 1000 years which are greater than that for 0.2% uranium ore (carnotite). The candidates which require separation for transmutation are the actinides; Np, Pu, Am, and Cu and the fission products; I and Tc. Certain assumptions were made for the parameters for the ILFR and its operating conditions, and a system evaluation was done. System evaluations indicate that blanket waste loadings on the order of several percent of the total concentration result in attractive performance in terms of high transmutation capacities and low blanket processing requirments. It appears that transmutation system goals in terms of toxicity reduction are achievable with a modest number of transmuters. In addition, requirements for transmuter performance, chemical processing capacity and chemical separation efficiency appear to be within projected values for this technology

Enhancing MA transmutation by irradiation of (MA, Zr)Hx in FBR blanket region - 5383

International Nuclear Information System (INIS)

Konashi, K.; Ikeda, K.; Itoh, K.; Hirai, M.; Koyama, T.; Kurosaki, K.

2015-01-01

Minor actinide (MA) hydride is proposed as transmutation target in sodium-cooled mixed oxide fuelled fast reactor. Preliminarily calculations have been done to check the transmutation efficiency of MA hydride targets. Three different types of MA target, MA-Zr alloy, (MA, Zr)O 2 and (MA, Zr)H x , have been compared on MA transmutation rate. The targets are assumed to be loaded around an active core in a 280 MWe sodium-cooled reactor; 54 MA target assemblies are respectively arranged in a row in the radial blanket zone. They are supposed to be irradiated for one year and then be cooled for 60 days. The transmuted mass has been evaluated by three-dimensional diffusion calculation to be 25, 15, 61 kg/EFPY for the alloy, the oxide and the hydride respectively, where production of MA in the active core is taken into account. The transmutation mass by (MA, Zr)H x is much larger than those by the other types of targets, while the core characteristics remain sound by locating MA targets outside of the active core. On top of that, two kinds of (MA, Zr)O 2 targets which are combined with ZrH x (x=1.7) pins have been calculated. Major Research/Development items are selected to establish the MA hydride transmutation method by reviewing technologies applicable to the transmutation system. The practical use of the MA hydride transmutation method is not far ahead technically, since this method can be developed by the extension of existing technologies. (authors)

Scenarios for Minor Actinides Transmutation in the Frame of the French Act for Waste Management

International Nuclear Information System (INIS)

Meyer, M.; Coquelet-Pascal, C.; Girieud, R.; Tiphine, M.; Eschbach, R.; Chabert, C.; Garzenne, C.; Barbrault, P.; Gannaz, B.; Van Den Durpel, L.; Favet, D.; Arslan, M.; Carlier, B.; Caron-Charles, M.; Lefèvre, J.C.

2013-01-01

Conclusion: • Different transmutation scenarios have been evaluated: homogeneous transmutation, AmBB, MABB. • Homogeneous transmutation: – The MA content peak at the beginning of the transmutation can be reduced from 3,9% to 2,5% thanks to a reprocessing optimization. – Delaying the SFR deployment to 2080 increases this peak from 3,9% to 4,7%. Due to the constraints on reprocessing, the optimization may be less efficient in this case. • Heterogeneous transmutation: – Shorting the AmBB irradiation time from 10 cycles to 5 cycles and reducing their Am content from 20% to 10%: - reduces AmBB decay heat (-45% at the cooling beginning); - leads to an increase in the Am mass in cycle (+20% in 2150). • Impact of the CFV core: – In heterogeneous mode, the CFV transmutation rate being better than the SFRV2B one, the MA inventory is reduced by 22% in 2150. – In homogeneous mode, the reduction of the fissile mass in core leads to an increase of the MA peak at the beginning of the transmutation (3,9% → 5,6%). There’s no impact on the MA inventory

Target fuels for plutonium and minor actinide transmutation in pressurized water reactors

International Nuclear Information System (INIS)

Washington, J.; King, J.; Shayer, Z.

2017-01-01

Highlights: • We evaluate transmutation fuels for plutonium and minor actinide destruction in LWRs. • We model a modified AP1000 fuel assembly in SCALE6.1. • We evaluate spectral shift absorber coatings to improve transmutation performance. - Abstract: The average nuclear power plant produces twenty metric tons of used nuclear fuel per year, containing approximately 95 wt% uranium, 1 wt% plutonium, and 4 wt% fission products and transuranic elements. Fast reactors are a preferred option for the transmutation of plutonium and minor actinides; however, an optimistic deployment time of at least 20 years indicates a need for a nearer-term solution. This study considers a method for plutonium and minor actinide transmutation in existing light water reactors and evaluates a variety of transmutation fuels to provide a common basis for comparison and to determine if any single target fuel provides superior transmutation properties. A model developed using the NEWT module in the SCALE 6.1 code package provided performance data for the burnup of the target fuel rods in the present study. The target fuels (MOX, PuO_2, Pu_3Si_2, PuN, PuUZrH, PuZrH, PuZrHTh, and PuZrO_2) are evaluated over a 1400 Effective Full Power Days (EFPD) interval to ensure each assembly remained critical over the entire burnup period. The MOX (5 wt% PuO_2), Pu_0_._3_1ZrH_1_._6Th_1_._0_8, and PuZrO_2MgO (8 wt% Pu) fuels result in the highest rate of plutonium transmutation with the lowest rate of curium-244 production. This study selected eleven different burnable absorbers (B_4C, CdO, Dy_2O_3, Er_2O_3, Eu_2O_3, Gd_2O_3, HfO_2, In_2O_3, Lu_2O_3, Sm_2O_3, and TaC) for evaluation as spectral shift absorber coatings on the outside of the fuel pellets to determine if an absorber coating can improve the transmutation properties of the target fuels. The PuZrO_2MgO (8 wt% Pu) target fuel with a coating of Lu_2O_3 resulted in the highest rate of plutonium transmutation with the greatest reduction in curium

Target fuels for plutonium and minor actinide transmutation in pressurized water reactors

Energy Technology Data Exchange (ETDEWEB)

Washington, J., E-mail: jwashing@gmail.com [Nuclear Science and Engineering Program, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); King, J., E-mail: kingjc@mines.edu [Nuclear Science and Engineering Program, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); Shayer, Z., E-mail: zshayer@mines.edu [Department of Physics, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States)

2017-03-15

Highlights: • We evaluate transmutation fuels for plutonium and minor actinide destruction in LWRs. • We model a modified AP1000 fuel assembly in SCALE6.1. • We evaluate spectral shift absorber coatings to improve transmutation performance. - Abstract: The average nuclear power plant produces twenty metric tons of used nuclear fuel per year, containing approximately 95 wt% uranium, 1 wt% plutonium, and 4 wt% fission products and transuranic elements. Fast reactors are a preferred option for the transmutation of plutonium and minor actinides; however, an optimistic deployment time of at least 20 years indicates a need for a nearer-term solution. This study considers a method for plutonium and minor actinide transmutation in existing light water reactors and evaluates a variety of transmutation fuels to provide a common basis for comparison and to determine if any single target fuel provides superior transmutation properties. A model developed using the NEWT module in the SCALE 6.1 code package provided performance data for the burnup of the target fuel rods in the present study. The target fuels (MOX, PuO{sub 2}, Pu{sub 3}Si{sub 2}, PuN, PuUZrH, PuZrH, PuZrHTh, and PuZrO{sub 2}) are evaluated over a 1400 Effective Full Power Days (EFPD) interval to ensure each assembly remained critical over the entire burnup period. The MOX (5 wt% PuO{sub 2}), Pu{sub 0.31}ZrH{sub 1.6}Th{sub 1.08}, and PuZrO{sub 2}MgO (8 wt% Pu) fuels result in the highest rate of plutonium transmutation with the lowest rate of curium-244 production. This study selected eleven different burnable absorbers (B{sub 4}C, CdO, Dy{sub 2}O{sub 3}, Er{sub 2}O{sub 3}, Eu{sub 2}O{sub 3}, Gd{sub 2}O{sub 3}, HfO{sub 2}, In{sub 2}O{sub 3}, Lu{sub 2}O{sub 3}, Sm{sub 2}O{sub 3}, and TaC) for evaluation as spectral shift absorber coatings on the outside of the fuel pellets to determine if an absorber coating can improve the transmutation properties of the target fuels. The PuZrO{sub 2}MgO (8 wt% Pu) target

Partitioning and Transmutation: IAEA Activities

International Nuclear Information System (INIS)

Basak, U.; Monti, S.; )

2015-01-01

Full text of publication follows: The importance of partitioning and transmutation (P and T) processes for sustaining nuclear energy growth in the world has been realised in several countries across the world. P and T processes aim at separation and recycling of actinides including minor actinides (MAs) from the spent fuel or high-level liquid waste. The objective of these processes include reuse of separated fissile materials from spent nuclear fuels to obtain energy, enhance resource utilisation, reduce the disposal of toxic radio-nuclides and improve long-term performance of geological repositories. R and D programmes have been launched in many of the Member States to develop advanced partitioning process based on either aqueous or pyro to recover MAs along with other actinides as well as automated and remote techniques for manufacturing fuels containing MAs for the purpose of transmuting them either in fast reactors or accelerator driven hybrids. A number of Member States have been also developing such transmutation systems with the aim to construct and operate demo plants and prototypes in the next decade. The International Atomic Energy Agency has a high priority for the activities on partitioning and transmutation and regularly organises conferences, workshops, seminars and technical meetings in the areas of P and T as a part of information exchange and knowledge sharing at the international level. In the recent past, the Agency organised two technical meetings on advanced partitioning processes and actinide recycle technologies with the objective of providing a common platform for the scientists and engineers working in the areas of separation of actinides along with MAs from spent nuclear fuels and manufacturing of advanced fuels containing MAs in order to bridge the technological gap between them. In 2010, the Agency concluded a Coordinated Research Project (CRP) related to Assessment of Partitioning Processes. The Agency also conducted a first CRP on

Accelerator-driven transmutation: a high-tech solution to some nuclear waste problems

International Nuclear Information System (INIS)

Hechanova, A.E.

2000-01-01

This paper discusses current technical and political issues regarding the innovative concept of using accelerator-driven transmutation processes for nuclear waste management. Two complex and related issues are addressed. First, the evolution and improvements of the design technologies are identified to indicate that there has been sufficient technological advancement with regard to a 1991 scientific peer review to warrant the advent of a large-scale national research and development program. Second, the economics and politics of the transmutation system are examined to identify non-technical barriers to the implementation of the program. Transmutation of waste has been historically viewed by nuclear engineers as one of those technologies that is too good to be true and probably too expensive to be feasible. The concept discussed in the present paper uses neutrons ( which result from protons accelerated into spallation targets)to transmute the major very long-lived hazardous materials such as the radioactive isotopes of technetium, iodine, neptunium, plutonium, americium, and curium. Although not a new concept, accelerator-driven transmutation technology (ADTT) lead by a team at Los Alamos National Laboratory (LANL) has made some significant advances which are discussed in the present paper. (authors)

Nuclear Wastes: Technologies for Separations and Transmutation

National Research Council Canada - National Science Library

.... The committee examines the currently used "once-through" fuel cycle versus different alternatives of separations and transmutation technology systems, by which hazardous radionuclides are converted...

Development of a fast reactor for minor actinides transmutation - (1) Overview and method development - 5092

International Nuclear Information System (INIS)

Takeda, T.; Usami, S.; Fujimura, K.; Takakuwa, M.

2015-01-01

The Ministry of Education, Culture, Sports, Science and Technology in Japan has launched a national project entitled 'technology development for the environmental burden reduction' in 2013. The present study is one of the studies adopted as the national project. The objective of the study is the efficient and safe transmutation and volume reduction of minor actinides (MA) with long-lived radioactivity and high decay heat contained in high level radioactive wastes by using sodium cooled fast reactors. We are developing MA transmutation core concepts which harmonize efficient MA transmutation with core safety. To accurately design the core concepts we have improved calculation methods for estimating the transmutation rate of individual MA nuclides, and estimating and reducing uncertainty of MA transmutation. The overview of the present project is first described. Then the method improvement is presented with numerical results for a minor-actinide transmutation fast reactor. The analysis is based on Monju reactor data. (authors)

Experimental demonstration of free-space optical vortex transmutation with polygonal lenses.

Science.gov (United States)

Gao, Nan; Xie, Changqing

2012-08-01

Vortex transmutation was predicted to take place when vortices interact with systems possessing discrete rotational symmetries of finite order [Phys. Rev. Lett.95, 123901 (2005)]. Here we report what is believed to be the first experimental demonstration of vortex transmutation. We show that in free space, by simply inserting polygonal lenses into the optical path, the central vorticity of a coaxially incident optical vortex can be changed following the modular transmutation rule. We generate the wavefront at the exit face of the lenses with computer generated holograms and measure the output vorticity using the interference patterns at the focal plane. The results agree well with theoretical predictions.

Analysis on Radioactive Waste Transmutation in Light Water cooled Hyb-WT

International Nuclear Information System (INIS)

Hong, Seonghee; Kim, Myung Hyun

2014-01-01

A feasibility of realization is much higher in FFHR compared with pure fusion. A combination of plasma fusion source for neutrons with a subcritical reactor at the blanket side has much higher capability in transmutation of waste as well as reactor safety compared with fission reactor options. Fusion-Fission Hybrid Reactor (FFHR) uses various coolants depending on the purpose. It is important that coolant being used should be suitable to reactor purpose, because reactor performance and the design constraints may change depending on the coolant. There are basically two major groups of coolants for FFHR. One group of coolant does not contain Li. They are Na, Pb-Bi, H 2 O and D 2 O. The other group contains Li for tritium breeding. They are Li, LiPb, LiSN, FLIBE and FLiNaBe. Currently, the issue in FFHR is its implication for radioactive waste transmutation (FFHR for WT). Because radioactive wastes of spent nuclear fuel (SNF) are transmuted using fusion neutron source. Therefore a suitable coolant should be used for effective waste transmutation. . In FFHR for WT, LiPb coolant is being used mainly because of tritium production in Li and high neutron economic through reaction in Pb. However different coolants use such as Na, Pb-Bi are used in fast reactors and accelerator driven systems (ADS) having same purpose. In this study, radioactive waste transmutation performance of various coolants mentioned above will be compared and analyzed. Through this study, the coolants are judged primarily for their support to waste transmutation disregarding their limitation to reactor design and tritium breeding capability. First, performance of the light water coolant regarding radioactive waste transmutation was analyzed among various coolants mentioned above. In this paper, performance of radioactive waste transmutation can be known depending on different volume fractions (54.53, 60.27, 97.94vol.%) of the light water. Light water dose required fusion power lower than LiPb due to

Transmutation of stable isotopes and deactivation of radioactive waste in growing biological systems

International Nuclear Information System (INIS)

Vysotskii, Vladimir I.; Kornilova, Alla A.

2013-01-01

Highlights: ► The phenomena of isotope transmutation in growing microbiological cultures were investigated. ► Transmutation in microbiological associations is 20 times more effective than in pure cultures. ► Transmutation of radioactive nuclei to stable isotopes in such associations was investigated. ► The most accelerated rate of Cs 137 to stable Ba 138 isotope transmutation was 310 days. ► “Microbiological deactivation” may be used for deactivation of Chernobyl and Fukushima areas. - Abstract: The report presents the results of qualifying examinations of stable and radioactive isotopes transmutation processes in growing microbiological cultures. It is shown that transmutation of stable isotopes during the process of growth of microbiological cultures, at optimal conditions in microbiological associations, is 20 times more effective than the same transmutation process in the form of “one-line” (pure) microbiological cultures. In the work, the process of direct, controlled decontamination of highly active intermediate lifetime and long-lived reactor isotopes (reactor waste) through the process of growing microbiological associations has been studied. In the control experiment (flask with active water but without microbiological associations), the “usual” law of nuclear decay applies, and the life-time of Cs 137 isotope was about 30 years. The most rapidly increasing decay rate, which occurred with a lifetime τ * ≈ 310 days (involving an increase in rate, and decrease in lifetime by a factor of 35 times) was observed in the presence of Ca salt in closed flask with active water contained Cs 137 solution and optimal microbiological association

Nuclei transmutation by collisions with fast hadrons and nuclei

International Nuclear Information System (INIS)

Strugalski, Z.; Strugalska-Gola, E.; Drzymala, A.

1998-01-01

Atomic nuclei change their mass- and charge-numbers if bombarded by fast hadrons and nuclei; the transmutation appears as a complicated process. It proceeds in a definite way - through a few stages or phases. Adequate identification of the nucleons and light nuclear fragments emitted and evaporated in a hadron-nucleus or nucleus-nucleus collisions and in the collision-induced intranuclear reactions allows one to estimate quantitatively the nuclei transmutations in the various stages (phases) of the process

Experience gained during 10 years transmutation experiments in Dubna

Science.gov (United States)

Zamani, M.; Fragopoulou, M.; Manolopoulou, M.; Stoulos, S.; Brandt, R.; Westmeier, W.; Krivopustov, M.; Sosnin, A.; Golovatyuk, S.

2006-05-01

Transmutation, the procedure of transforming long-lived radioactive isotopes into stable or short-lived, was proposed for reducing the amount of radioactive waste resulting from technological applications of nuclear fission. The Accelerator Driven Systems (ADS) provide the possibility to generate intense neutron spectrum yielding in an effective transmutation of unwanted isotopes. Such experiments are being carried out for the last 10 years in Synchrophasotron / Nuclotron accelerators at the Veksler-Baldin Laboratory of High Energies of the Joint Institute for Nuclear Research in Dubna, Russia. Thick Pb and Pb-U targets, surrounded by moderators, have been irradiated by protons in the energy range of 0.5-7.4 GeV. Neutron fluence measurements have been performed by different techniques of passive detectors (neutron activation detectors, solid state nuclear track detectors). Transmutation of 129I, 237Np, 239Pu was studied. The results of these experiments are presented and discussed.

Electronic Transmutation (ET): Chemically Turning One Element into Another.

Science.gov (United States)

Zhang, Xinxing; Lundell, Katie A; Olson, Jared K; Bowen, Kit H; Boldyrev, Alexander I

2018-03-08

The concept of electronic transmutation (ET) depicts the processes that by acquiring an extra electron, an element with the atomic number Z begins to have properties that were known to only belong to its neighboring element with the atomic number Z+1. Based on ET, signature compounds and chemical bonds that are composed of certain elements can now be designed and formed by other electronically transmutated elements. This Minireview summarizes the recent developments and applications of ET on both the theoretical and experimental fronts. Examples on the ET of Group 13 elements into Group 14 elements, Group 14 elements into Group 15 elements, and Group 15 elements into Group 16 elements are discussed. Compounds and chemical bonding composed of carbon, silicon, germanium, phosphorous, oxygen and sulfur now have analogues using transmutated boron, aluminum, gallium, silicon, nitrogen, and phosphorous. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Graphical representation of transmutation and decay chain data, transmutation cross section and delayed gamma ray emission data

International Nuclear Information System (INIS)

Seki, Yasushi; Iida, Hiromasa; Kawasaki, Hiromitsu.

1982-09-01

In a D-T burning fusion reactor, the neutron induced activity severely limits personnel access to the reactor. Accurate evaluation of the induced activity and dose rate is necessary to conduct effective biological shield design. In order to evaluate the dose rate accurately, considerable amount of activation data is required. This report gives graphical representation of transmutation and decay chain data, transmutation cross section data and delayed gamma ray emission data for 116 nuclides of interest in terms of fusion reactor design. This graphical representation was made with hope of producing a reference for examining activation problems. It has already been shown to be effective in correcting inappropriate data. A computer code AMOEBA developed for the checking and plotting of the activation data is also described in this report. (author)

Optimization of accelerator-driven technology for LWR waste transmutation

International Nuclear Information System (INIS)

Bowman, C.D.

1996-01-01

The role of accelerator-driven transmutation technology is examined in the context of the destruction of actinide waste from commercial light water reactors. It is pointed out that the commercial plutonium is much easier to use for entry-level nuclear weapons than weapons plutonium. Since commercial plutonium is easier to use, since there is very much more of it already, and since it is growing rapidly, the permanent disposition of commercial plutonium is an issue of greater importance than weapons plutonium. The minor actinides inventory, which may be influenced by transmutation, is compared in terms of nuclear properties with commercial and weapons plutonium and for possible utility as weapons material. Fast and thermal spectrum systems are compared as means for destruction of plutonium and the minor actinides. it is shown that the equilibrium fast spectrum actinide inventory is about 100 times larger than for thermal spectrum systems, and that there is about 100 times more weapons-usable material in the fast spectrum system inventory compared to the thermal spectrum system. Finally it is shown that the accelerator size for transmutation can be substantially reduced by design which uses the accelerator-produced neutrons only to initiate the unsustained fission chains characteristic of the subcritical system. The analysis argues for devoting primary attention to the development of thermal spectrum transmutation technology. A thermal spectrum transmuter operating at a fission power of 750-MWth fission power, which is sufficient to destroy the actinide waste from one 3,000-MWth light water reactor, may be driven by a proton beam of 1 GeV energy and a current of 7 mA. This accelerator is within the range of realizable cyclotron technology and is also near the size contemplated for the next generation spallation neutron source under consideration by the US, Europe, and Japan

Multiple Tier Fuel Cycle Studies for Waste Transmutation

International Nuclear Information System (INIS)

Hill, R.N.; Taiwo, T.A.; Stillman, J.A.; Graziano, D.J.; Bennett, D.R.; Trellue, H.; Todosow, M.; Halsey, W.G.; Baxter, A.

2002-01-01

As part of the U.S. Department of Energy Advanced Accelerator Applications Program, a systems study was conducted to evaluate the transmutation performance of advanced fuel cycle strategies. Three primary fuel cycle strategies were evaluated: dual-tier systems with plutonium separation, dual-tier systems without plutonium separation, and single-tier systems without plutonium separation. For each case, the system mass flow and TRU consumption were evaluated in detail. Furthermore, the loss of materials in fuel processing was tracked including the generation of new waste streams. Based on these results, the system performance was evaluated with respect to several key transmutation parameters including TRU inventory reduction, radiotoxicity, and support ratio. The importance of clean fuel processing (∼0.1% losses) and inclusion of a final tier fast spectrum system are demonstrated. With these two features, all scenarios capably reduce the TRU and plutonium waste content, significantly reducing the radiotoxicity; however, a significant infrastructure (at least 1/10 the total nuclear capacity) is required for the dedicated transmutation system. (authors)

Transmutation: The Roots of the Dream.

Science.gov (United States)

Karpenko, Vladimir

1995-01-01

Examines the history of alchemical attempts at transmutation and classifies them by differing approaches and techniques. Traces the development of alchemy in Asia, Europe, and the Middle East, and compares alchemy with craftsmanship. (18 references) (DDR)

Partitioning and transmutation of transuranium elements under nuclear phase-out conditions. Technically reliable?; Transmutation von Transuranen unter den Randbedingungen des Kernenergieausstiegs. Technisch machbar?

Energy Technology Data Exchange (ETDEWEB)

Merk, Bruno; Rohde, Ulrich [Helmholtz-Zentrum Dresden-Rossendorf, Dresden (Germany)

2016-04-15

The German government has decided for the nuclear phase out, but a decision on a strategy for the management of the highly radioactive waste is not defined yet. Partitioning and Transmutation (P and T) could be considered as a technological option in the process of management of highly radioactive waste management, therefore a wide study has been conducted. In this group objectives for P and T and the boundary conditions of the phase out have been discussed. The fulfillment of the given objectives is analyzed using simulations of molten salt reactors with fast neutron spectrum. It is shown that the efficient transmutation of all existing transuranium isotopes would be possible in 3 to 4 reactors in a time frame of 45 to 60 years. Further on a detailed balance of different isotopic inventories is given to allow a deeper understanding of the processes during transmutation.

Actinide partitioning and transmutation program progress report, October 1, 1976--March 31, 1977

International Nuclear Information System (INIS)

Blomeke, J.O.; Tedder, D.W.

1977-01-01

Experimental work on the 16 tasks comprising the Actinide Partitioning and Transmutation Program was initiated at the various sites. This work included the development of conceptual material balance flowsheets which define integrated waste systems supporting an LWR fuel reprocessing plant and a mixed (U-Pu) oxide fuel refabrication plant. In addition, waste subsystems were defined for experimental evaluation. Computer analysis of partitioning-transmutation, utilizing an LMFBR for transmutation, was completed for both constant and variable waste actinide generation rates

Partitioning and Transmutation of minor actinides

International Nuclear Information System (INIS)

Koch, L.; Wellum, R.

1991-01-01

The partitioning of minor actinides from spent fuels and their transmutation into short-lived fission products has been the topic of two dedicated meetings organized jointly by the European Commission and the OECD. The conclusion of the last meeting in 1980, in short, was that partitioning and transmutation of minor actinides, especially in fast reactors, seemed possible. However, the incentive, which would be a reduction of the radiological hazard to the public, was too small if long-lived fission products were not included. Furthermore this meeting showed that minor actinide targets or possible nuclear fuels containing minor actinides for transmutation had not yet been developed. The European Institute for Transuranium Elements took up this task and has carried it out as a small activity for several years. Interests expressed recently by an expert meeting of the OECD/NEA (Paris, 25 April 1989), which was initiated by the proposed Japanese project Omega, led us to the conclusion that the present state of knowledge should be looked at in a workshop environment. Since the Japanese proposal within the project Omega is based on a broader approach we needed this evaluation to assess the relevance of our present activity and wanted to identifiy additional studies which might be needed to cover possible future demands from the public. This workshop was therefore organized, and participants active in the field from EC countries, the USA and Japan were invited

Transmutation of technetium: results of the EFTTRA-T1 experiment

International Nuclear Information System (INIS)

Konings, R.J.M.; Stalios, A.D.; Walker, C.T.; Cocuaud, N.

1998-01-01

The transmutation of the fission product 99 Tc was studied by neutron irradiation in the High Flux Reactor at Petten. Six metallic rods of pure Tc, distributed over three capsules, were irradiated during eight reactor cycles to a total neutron fluence of about 2 x 10 26 m -2 . Metallographic examinations showed that no changes in the microstructure were visible after the irradiation. Electron probe microanalysis (EPMA) of the radial distribution of Ru, the product of the transmutation process, showed an increase from about 6% in the centre to 12-18% near the rim of the pellets. This effect is due to resonance-shielding of epithermal neutrons in the rim region. Mass spectrometric analysis of the pellet-average Ru concentration showed that the extent of transmutation is about 6-7%. (orig.)

Transmutation studies of minor actinides in high intensity neutron fluxes

International Nuclear Information System (INIS)

Fioni, G.; Bolognese, T.; Cribier, M.; Marie, F.; Roettger, S.; Faust, H.; Leconte, Ph.

1999-01-01

Integral measurements of nuclear data and of the transmutation potential in specific neutron fluxes, constitute the fastest and essential way to overcome to the large uncertainties present in the nuclear data libraries. In the frame of the activities of the Directorate for Science of Matter (DSM) of the French Atomic Energy Authority (CEA), a new project is proposed so as to carry out integral measurements relevant for nuclear waste transmutation systems. A new beam tube will be installed to irradiate actinides and fission fragment samples at different distances from the fuel element of the ILL reactor. Variable neutron energy spectra could then be obtained by choosing the distance between the sample and the fuel element, opening the way to the determination of the ideal physical conditions to incinerate nuclear waste in hybrid transmutation systems. (author)

Transmutation performance analysis on coolant options in a hybrid reactor system design for high level waste incineration

Energy Technology Data Exchange (ETDEWEB)

Hong, Seong-Hee; Siddique, Muhammad Tariq; Kim, Myung Hyun, E-mail: mhkim@khu.ac.kr

2015-11-15

Highlights: • Waste transmutation performance was compared and analyzed for seven different coolant options. • Reactions of fission and capture showed big differences depending on coolant options. • Moderation effect significantly affects on energy multiplication, tritium breeding and waste transmutation. • Reduction of radio-toxicities of TRUs showed different trend to coolant choice from performance of waste transmutation. - Abstract: A fusion–fission hybrid reactor (FFHR) is one of the most attractive candidates for high level waste transmutation. The selection of coolant affects the transmutation performance of a FFHR. LiPb coolant, as a conventional coolant for a FFHR, has problems such as reduction in neutron economic and magneto-hydro dynamics (MHD) pressure drop. Therefore, in this work, transmutation performance is evaluated and compared for various coolant options such as LiPb, H{sub 2}O, D{sub 2}O, Na, PbBi, LiF-BeF{sub 2} and NaF-BeF{sub 2} applicable to a hybrid reactor for waste transmutation (Hyb-WT). Design parameters measuring performance of a hybrid reactor were evaluated by MCNPX. They are k{sub eff}, energy multiplication factor, neutron absorption ratio, tritium breeding ratio, waste transmutation ratio, support ratio and radiotoxicity reduction. Compared to LiPb, H{sub 2}O and D{sub 2}O are not suitable for waste transmutation because of neutron moderation effect. Waste transmutation performances with Na and PbBi are similar to each other and not different much from LiPb. Even though molten salt such as LiF-BeF{sub 2} and NaF-BeF{sub 2} is good for avoiding MHD pressure drop problem, waste transmutation performance is dropped compared with LiPb.

Electron trap annealing in neutron transmutation doped silicon

DEFF Research Database (Denmark)

Guldberg, J.

1977-01-01

Silicon doped by neutron transmutation to 1.2×1014 phosphorus atoms/cm3 was investigated with deep level transient spectroscopy using evaporated Au/n-Si diodes. Seven bulk electron traps were identified which appear after 30 min N2 anneal at temperatures between 425 and 725 °C. Five of these anne......Silicon doped by neutron transmutation to 1.2×1014 phosphorus atoms/cm3 was investigated with deep level transient spectroscopy using evaporated Au/n-Si diodes. Seven bulk electron traps were identified which appear after 30 min N2 anneal at temperatures between 425 and 725 °C. Five...

Transmutation of fission products and actinide waste at Hanford

Energy Technology Data Exchange (ETDEWEB)

Daemen, L.L.; Pitcher, E.J.; Russell, G.J. [Los Alamos National Laboratory, NM (United States)

1995-10-01

The authors studied the neutronics of an ATW system for the transmutation of the fission products ({sup 99}Tc in particular) and the type of actinide waste stored in several tanks at Hanford. The heart of the system is a highly-efficient neutron production target. It is surrounded by a blanket containing a moderator/reflector material, as well as the products to be transmuted. The fission products are injected into the blanket in the form of an aqueous solution in heavy water, whereas an aqueous actinides slurry is circulated in the outer part of the blanket. For the sake of definiteness, the authors focussed on {sup 99}Tc (the most difficult fission product to transmute), and {sup 239}Pu, {sup 237}Np, and {sup 241}Am. Because of the low thermal neutron absorption cross-section of {sup 99}Tc, considerable care and effort must be devoted to the design of a very efficient neutron source.

HYPERFUSE: a hypervelocity inertial confinement system for fusion energy production and fission waste transmutation

International Nuclear Information System (INIS)

Makowitz, H.; Powell, J.R.; Wiswall, R.

1980-01-01

Parametric system studies of an inertial confinement fusion (ICF) reactor system to transmute fission products from a LWR economy have been carried out. The ICF reactors would produce net power in addition to transmuting fission products. The particular ICF concept examined is an impact fusion approach termed HYPERFUSE, in which hypervelocity pellets, traveling on the order of 100 to 300 km/sec, collide with each other or a target block in a reactor chamber and initiate a thermonuclear reaction. The DT fusion fuel is contained in a shell of the material to be transmuted, e.g., 137 Cs, 90 Sr, 129 I, 99 Tc, etc. The 14-MeV fusion neutrons released during the pellet burn cause transmutation reactions (e.g., (n,2n), (n,α), (n,γ), etc.) that convert the long-lived fission products (FP's) either to stable products or to species that decay with a short half-life to a stable product. The transmutation parametric studies conclude that the design of the hypervelocity projectiles should emphasize the achievement of high densities in the transmutation regions (greater than the DT fusion fuel density), as well as the DT ignition and burn criterion (rho R = 1.0 to 3.0) requirements. These studies also indicate that masses on the order of 1.0 g at densities of rho greater than or equal to 500.0 g/cm 3 are required for a practical fusion-based fission product transmutation system

Technology readiness of partitioning and transmutation toward closed fuel cycle in Japan

International Nuclear Information System (INIS)

Ikeda, Kazumi; Kurata, Masaki; Morita, Yasuji; Tsujimoto, Kazufumi; Minato, Kazuo; Koyama, Shin-ichi

2011-01-01

This paper treats technology readiness level (TRL) assessment of Partitioning and Transmutation (P-T) toward closed fuel cycle in JAPAN. The purpose is providing clarified information related to the current maturity of the partitioning and transmutation technologies by applying the methodology of TRL, parallel to attempting to establish common indications among relating technology area. The methodology should be one of useful communication tools between specialists and management level, and also among countries interested in the P-T technologies. The generic TRL in this study is based on the GNEP (Global Nuclear Energy Partnership)'s definition: TRL 3 shows the status that critical function is proved and elemental technologies are identified, TRL 4 represents that relating technologies are validated at bench scale in laboratory environment, and TRL 5 achieves the completion of development related to the subsystem and elemental technologies. Detailed indications are established through discussion of the relating specialists. Reviewed technological area includes P-T and minor actinide (MA) cycle: Fast Breeder Reactor (FBR) and Accelerator driven system (ADS) for MA transmutation, partitioning processes, and MA-bearing fuels. The assessments reveal that TRL spreads around TRL 3 to TRL 4 because each system requires more the development of elemental technologies. Transmutation core of FBR is assessed to be TRL 4 in that MA bearing integral test is required additionally, and ADS becomes TRL 3 because the elemental technologies were identified and the requirements were specified. Consequently, the common key issue is how the nuclear calculation methodology will be validated for MA-bearing-fuelled core, since several percentages of MA changes the void reactivity and the Doppler Effect significantly, which are inherently important in reactor safety. It should be that critical experiments with several kg of americium or more are difficult in the existing experimental

Accelerator-driven sub-critical target concept for transmutation of nuclear wastes

International Nuclear Information System (INIS)

Van Tuyle, G.J.; Todosow, M.; Aronson, A.L.; Takahashi, H.; Geiger, M.J.

1991-01-01

A means of transmuting key long-lived nuclear wastes, primarily the minor actinides (Np, Am, Cm) and iodine, using a hybrid proton accelerator and sub-critical lattice, is proposed. By partitioning the components of the light water reactor (LWR) spent fuel and by transmuting key elements, such as the plutonium, the minor actinides, and a few of the long-lived fission products, some of the most significant challenges in building a waste repository can be substantially reduced. The proposed machine, based on the described PHOENIX Concept, would transmute the minor actinides and the iodine produced by 75 LWRs, and would generate usable electricity (beyond that required to run the large accelerator) of 850 MW e . 19 refs., 20 figs

Analysis of advanced european nuclear fuel cycle scenarios including transmutation and economical estimates

International Nuclear Information System (INIS)

Merino Rodriguez, I.; Alvarez-Velarde, F.; Martin-Fuertes, F.

2013-01-01

In this work the transition from the existing Light Water Reactors (LWR) to the advanced reactors is analyzed, including Generation III+ reactors in a European framework. Four European fuel cycle scenarios involving transmutation options have been addressed. The first scenario (i.e., reference) is the current fleet using LWR technology and open fuel cycle. The second scenario assumes a full replacement of the initial fleet with Fast Reactors (FR) burning U-Pu MOX fuel. The third scenario is a modification of the second one introducing Minor Actinide (MA) transmutation in a fraction of the FR fleet. Finally, in the fourth scenario, the LWR fleet is replaced using FR with MOX fuel as well as Accelerator Driven Systems (ADS) for MA transmutation. All scenarios consider an intermediate period of GEN-III+ LWR deployment and they extend for a period of 200 years looking for equilibrium mass flows. The simulations were made using the TR-EVOL code, a tool for fuel cycle studies developed by CIEMAT. The results reveal that all scenarios are feasible according to nuclear resources demand (U and Pu). Concerning to no transmutation cases, the second scenario reduces considerably the Pu inventory in repositories compared to the reference scenario, although the MA inventory increases. The transmutation scenarios show that elimination of the LWR MA legacy requires on one hand a maximum of 33% fraction (i.e., a peak value of 26 FR units) of the FR fleet dedicated to transmutation (MA in MOX fuel, homogeneous transmutation). On the other hand a maximum number of ADS plants accounting for 5% of electricity generation are predicted in the fourth scenario (i.e., 35 ADS units). Regarding the economic analysis, the estimations show an increase of LCOE (Levelized cost of electricity) - averaged over the whole period - with respect to the reference scenario of 21% and 29% for FR and FR with transmutation scenarios respectively, and 34% for the fourth scenario. (authors)

Researches on the management of high activity and long-lived radioactive wastes. Axis 1 - separation-transmutation

International Nuclear Information System (INIS)

2005-11-01

This document gathers the transparencies of seven presentations given at a technical workshop of the French nuclear energy society (SFEN) about the researches on separation-transmutation of high activity and long-lived radioactive wastes. The presentations deal with: inventory and radiotoxicity of the rad-wastes in concern; industrial experience; experience on chemical separation: molecules and processes; reactors physics and transmutation - reactors for transmutation; fuels and targets; scenarios that include transmutation; environmental impacts of these different scenarios. (J.S.)

Neutron transmutation doped Ge bolometers

Science.gov (United States)

Haller, E. E.; Kreysa, E.; Palaio, N. P.; Richards, P. L.; Rodder, M.

1983-01-01

Some conclusions reached are as follow. Neutron Transmutation Doping (NTD) of high quality Ge single crystals provides perfect control of doping concentration and uniformity. The resistivity can be tailored to any given bolometer operating temperature down to 0.1 K and probably lower. The excellent uniformity is advantaged for detector array development.

Present status of research activities on transmutation of actinides in Japan

International Nuclear Information System (INIS)

Amano, Hiroshi

1978-01-01

In Japan, the idea to make use of transmutation for the final disposal method of HLW was first examined by Ichimiya, Amano, Hamada et al., when the Japan Atomic Industry forum had organized a study committee for HLW treatment in 1973. This article has the scope to outline the present research activities on transmutation of actinides in Japan

Impact of partitioning and transmutation on the high level waste management

International Nuclear Information System (INIS)

Gonzalez-Romero, Enrique-Miguel

2010-01-01

The contribution is structured as follows: (i) Background on partitioning and transmutation; (ii) FP6 projects: RED-IMPACT; (iii) Advanced fuel cycle scenarios; (iv) Partitioning and transmutation expected performance; (v) Impact on the HLW thermal load; (vi) Impact on the deep geological disposal; and (vii) Impact on the performance assessment of deep geological disposal. (P.A.)

Present status and issues for accelerator driven transmutation system

International Nuclear Information System (INIS)

Mizumoto, Motoharu

2003-01-01

Proper treatment of high-level nuclear wastes (HLW) that are produced in operation of nuclear power plants is one of the most important problems for further utilization of nuclear energy. The purpose of the accelerator driven nuclear waste transmutation system (ADS) is to transmute these nuclei to stable or short-lived nuclei by various radiation-induced nuclear reactions. When ADS for HLW can be realized, burden to deep geological disposal can be considerably reduced. In the paper, present status and issues for ADS will be discussed. (author)

Transmutation of radioactive wastes from nuclear power plants. A contribution to the reduction of the final repository problem; Transmutation radioaktiver Reststoffe aus Kernkraftwerken. Ein Beitrag zur Verringerung der Endlagerproblematik

Energy Technology Data Exchange (ETDEWEB)

Mach, Manfred [Technische Univ. Berlin (Germany). Inst. fuer Technologie und Management

2015-07-01

The brochure on transmutation of radioactive wastes from nuclear power plants - a contribution to the reduction of the final repository problem covers the following issues: What is transmutation? Nuclear power in Germany; energy density of fuels; time span of energy resources; CO{sub 2} emissions from different energy sources; types of nuclear power plants in Germany; cost of German electricity generation plants; nuclear power plants worldwide; wastes from nuclear electricity production; radiation from fission products; radiation effects on humans, the nuclear fuel cycle, direct final disposal of radioactive wastes; risk assessment of the direct final disposal; partitioning of actinides; transmutation of actinides.

Analysis of the transmutational characteristics of a novel molten salt reactor concept

International Nuclear Information System (INIS)

Csom, Gy.; Feher, S.; Szieberth, M.

2001-01-01

One of the arguments most frequently brought up by the opponents of the utilization of nuclear energy is the requirement that the radioactive waste and the long-lived radioisotopes accumulated in the spent fuel should be isolated for a very long time from the biosphere. The solution is the elimination of long-lived actinides (plutonium isotopes and minor actinides) and long-lived fission products by transforming (transmuting) them into short-lived or stable nuclei. The high neutron flux required for transmutation can be realized in nuclear installations. these may be conventional therma; and fast reactors, furthermore dedicated devices, namely thermal and fast reactors and accelerator driven subcritical systems (ADSs), which are specifically designed for this purpose. Some of the most promising systems are the molten salt reactors and subcritical systems, in which the fuel and material to be transmuted circulate dissolved in some molten salt. In the present paper this transmutational device, as well as recommendations for the improvement are discussed in detail (Authors)

Statistical transmutation in doped quantum dimer models.

Science.gov (United States)

Lamas, C A; Ralko, A; Cabra, D C; Poilblanc, D; Pujol, P

2012-07-06

We prove a "statistical transmutation" symmetry of doped quantum dimer models on the square, triangular, and kagome lattices: the energy spectrum is invariant under a simultaneous change of statistics (i.e., bosonic into fermionic or vice versa) of the holes and of the signs of all the dimer resonance loops. This exact transformation enables us to define the duality equivalence between doped quantum dimer Hamiltonians and provides the analytic framework to analyze dynamical statistical transmutations. We investigate numerically the doping of the triangular quantum dimer model with special focus on the topological Z(2) dimer liquid. Doping leads to four (instead of two for the square lattice) inequivalent families of Hamiltonians. Competition between phase separation, superfluidity, supersolidity, and fermionic phases is investigated in the four families.

HYPERFUSE: a hypervelocity inertial confinement system for fusion energy production and fission waste transmutation

International Nuclear Information System (INIS)

Makowitz, H.; Powell, J.R.; Wiswall, R.

1980-01-01

Parametric system studies of an inertial confinement fusion (ICF) reactor system to transmute fission products from an LWR economy have been carried out. The ICF reactors would produce net power in addition to transmuting fission products. The particular ICF concept examined is an impact fusion approach termed HYPERFUSE, in which hypervelocity pellets, traveling on the order of 100 to 300 km/sec, collide with each other or a target block in a reactor chamber and initiate a thermonuclear reaction. The DT fusion fuel is contained in a shell of the material to be transmuted, e.g., 137 Cs, 90 Sr, 129 I, 99 Tc, etc. The 14-MeV fusion neutrons released during the pellet burn cause transmutation reactions (e.g., (n,2n), (n,α), (n,γ), etc.) that convert the long-lived fission products (FP's) either to stable products or to species that decay with a short half-life to a stable product. The transmutation parametric studies conclude that the design of the hypervelocity projectiles should emphasize the achievement of high densities in the transmutation regions (greater than the DT fusion fuel density), as well as the DT ignition and burn criterion (rho R=1.0 to 3.0) requirements

Capabilities of a DT tokamak fusion neutron source for driving a spent nuclear fuel transmutation reactor

International Nuclear Information System (INIS)

Stacey, W.M.

2001-01-01

The capabilities of a DT fusion neutron source for driving a spent nuclear fuel transmutation reactor are characterized by identifying limits on transmutation rates that would be imposed by tokamak physics and engineering limitations on fusion neutron source performance. The need for spent nuclear fuel transmutation and the need for a neutron source to drive subcritical fission transmutation reactors are reviewed. The likely parameter ranges for tokamak neutron sources that could produce an interesting transmutation rate of 100s to 1000s of kg/FPY (where FPY stands for full power year) are identified (P fus ∼ 10-100 MW, β N ∼ 2-3, Q p ∼ 2-5, R ∼ 3-5 m, I ∼ 6-10 MA). The electrical and thermal power characteristics of transmutation reactors driven by fusion and accelerator spallation neutron sources are compared. The status of fusion development vis-a-vis a neutron source is reviewed. (author)

An optimization methodology for heterogeneous minor actinides transmutation

Science.gov (United States)

Kooyman, Timothée; Buiron, Laurent; Rimpault, Gérald

2018-04-01

In the case of a closed fuel cycle, minor actinides transmutation can lead to a strong reduction in spent fuel radiotoxicity and decay heat. In the heterogeneous approach, minor actinides are loaded in dedicated targets located at the core periphery so that long-lived minor actinides undergo fission and are turned in shorter-lived fission products. However, such targets require a specific design process due to high helium production in the fuel, high flux gradient at the core periphery and low power production. Additionally, the targets are generally manufactured with a high content in minor actinides in order to compensate for the low flux level at the core periphery. This leads to negative impacts on the fuel cycle in terms of neutron source and decay heat of the irradiated targets, which penalize their handling and reprocessing. In this paper, a simplified methodology for the design of targets is coupled with a method for the optimization of transmutation which takes into account both transmutation performances and fuel cycle impacts. The uncertainties and performances of this methodology are evaluated and shown to be sufficient to carry out scoping studies. An illustration is then made by considering the use of moderating material in the targets, which has a positive impact on the minor actinides consumption but a negative impact both on fuel cycle constraints (higher decay heat and neutron) and on assembly design (higher helium production and lower fuel volume fraction). It is shown that the use of moderating material is an optimal solution of the transmutation problem with regards to consumption and fuel cycle impacts, even when taking geometrical design considerations into account.

Evaluation of the possibility of plutonium and minor actinides transmutation in HWR

International Nuclear Information System (INIS)

Ghitescu, P.; Ghizdeanu, N. B.

2008-01-01

Partitioning and Transmutation (P and T) techniques could contribute to reduce the radioactive inventory and its associated radio-toxicity. Until now, for this purpose were studied ADS and/or FBR, but not HWR. There are several developed computer codes that analyze the inventory of the radio-nuclides in spent fuel before and after transmutation. WIMSD code is a deterministic lattice spectrum code, which can analyze the reactor neutronic behaviour It also has the capacity to generate burn up and can calculate the inventory of the radio-nuclides of the spent fuel. The advantage of WIMSD code is the variety of the created geometries, together with the big amount of calculated information (K-infinite, macroscopic cross-sections, burnable material radioactive inventory etc). Starting from WIMSD code, the paper presents a model, which simulates the possibility of fuel transmutation in PHWRs. First step was to propose a model, which simulates a CANDU reactor lattice and calculate the radionuclides inventory in an irradiated CANDU fuel bundle. The results were compared with the existing experimental data from CANDU reactors and the calculated parameters were found to be in good agreement with them. After the validation, several simulations were made for PHWRs in order to establish the optimal parameters, related to the efficiency of the transmutation process. Therefore, the code was used for a new type of fuel, containing Plutonium and minor actinides that could be transmuted. The new radioactive inventories were calculated. The simulations showed that Pu content decreases up to 8% in a CANDU reactor and 25% in an ACR. Thus, ACR can reduce the Plutonium inventory from MOX fuel and could be a transmutation solution. (authors)

Fission neutron irradiation of copper containing implanted and transmutation produced helium

DEFF Research Database (Denmark)

Singh, B.N.; Horsewell, A.; Eldrup, Morten Mostgaard

1992-01-01

High purity copper containing approximately 100 appm helium was produced in two ways. In the first, helium was implanted by cyclotron at Harwell at 323 K. In the second method, helium was produced as a transmutation product in 800 MeV proton irradiation at Los Alamos, also at 323 K. The distribut......High purity copper containing approximately 100 appm helium was produced in two ways. In the first, helium was implanted by cyclotron at Harwell at 323 K. In the second method, helium was produced as a transmutation product in 800 MeV proton irradiation at Los Alamos, also at 323 K...... as well as the effect of the presence of other transmutation produced impurity atoms in the 800 MeV proton irradiated copper will be discussed....

Energy Production and Transmutation of Nuclear Waste by Accelerator Driven Systems

Science.gov (United States)

Zhivkov, P. K.

2018-05-01

There is a significant amount of highly radiotoxic long-life nuclear waste (NW) produced by NPP (Nuclear Power Plants). Transmutation is a process which transforms NW into less radiotoxic nuclides with a shorter period of half-life by spallation neutrons or radiative capture of neutrons produced by ADS (Accelerator Driven System). In the processes of transmutation new radioactive nuclides are produced. ADS is big energy consumer equipment. It is a method for production of a high-flux and high-energy neutron field. All these processes occur in ADS simultaneously. ADS is able to transmute actinides and produce energy simultaneously. The article considers the energy production problems in ADS. Several ideas are developed regarding the solution of the global energy supply.

Progress in transmutation targets from Efttra

International Nuclear Information System (INIS)

Haas, D.; Fernandez, A.; Warin, D.; Bonnerot, J.M.; Garzenne, C.; Scaffidi-Argentina, F.; Maschek, W.; Schram, R.; Klaassen, F.

2007-01-01

Since 15 years, the EFTTRA partners have organised programmes to demonstrate the feasibility of the transmutation of americium in uranium-free targets. In the related transmutation scenario, the targets are introduced in a thermal neutron zone of a fast reactor, to maximize the efficiency of transmutation. Amongst these programmes, those carried out in the HFR reactor in Petten have led to important conclusions and are still at the core of the research in that field. The analysis of the EFTTRA T4 and T4bis irradiation experiments, carried out with targets of MgAl 2 O 4 +11 wt% 241 Am, showed that the release/trapping of helium is the key issue for target design, and also demonstrated a lack of technical benefits of this material, due to a unsatisfactory in-pile behaviour in terms of irradiation damage and chemical stability. A new irradiation experiment called HELIOS is currently under fabrication and will be carried out in HFR. The in-pile behaviour of U-free fuels and targets such as (Am,Zr)O 2 , (Pu,Am,Zr)O 2 , CERCER (MgO) or CERMET (Mo) will be examined. The irradiation temperature will be high enough in some of the pins to be able to tune the release of a significant fraction of helium produced so that the material swelling can be minimized as much as reasonably possible. The HELIOS irradiation experiment is planned to be carried out in the HFR core and shall last 300 full power days starting in 2007. (authors)

Spatial heterogeneity of tungsten transmutation in a fusion device

Science.gov (United States)

Gilbert, M. R.; Sublet, J.-Ch.; Dudarev, S. L.

2017-04-01

Accurately quantifying the transmutation rate of tungsten (W) under neutron irradiation is a necessary requirement in the assessment of its performance as an armour material in a fusion power plant. The usual approach of calculating average responses, assuming large, homogenised material volumes, is insufficient to capture the full complexity of the transmutation picture in the context of a realistic fusion power plant design, particularly for rhenium (Re) production from W. Combined neutron transport and inventory simulations for representative spatially heterogeneous high-resolution models of a fusion power plant show that the production rate of Re is strongly influenced by the surrounding local spatial environment. Localised variation in neutron moderation (slowing down) due to structural steel and coolant, particularly water, can dramatically increase Re production because of the huge cross sections of giant resolved resonances in the neutron-capture reaction of 186W at low neutron energies. Calculations using cross section data corrected for temperature (Doppler) effects suggest that temperature may have a relatively lesser influence on transmutation rates.

Actinides transmutation - a comparison of results for PWR benchmark

International Nuclear Information System (INIS)

Claro, Luiz H.

2009-01-01

The physical aspects involved in the Partitioning and Transmutation (P and T) of minor actinides (MA) and fission products (FP) generated by reactors PWR are of great interest in the nuclear industry. Besides these the reduction in the storage of radioactive wastes are related with the acceptability of the nuclear electric power. From the several concepts for partitioning and transmutation suggested in literature, one of them involves PWR reactors to burn the fuel containing plutonium and minor actinides reprocessed of UO 2 used in previous stages. In this work are presented the results of the calculations of a benchmark in P and T carried with WIMSD5B program using its new cross sections library generated from the ENDF-B-VII and the comparison with the results published in literature by other calculations. For comparison, was used the benchmark transmutation concept based in a typical PWR cell and the analyzed results were the k∞ and the atomic density of the isotopes Np-239, Pu-241, Pu-242 and Am-242m, as function of burnup considering discharge of 50 GWd/tHM. (author)

Deep burn transmutation of nuclear waste

International Nuclear Information System (INIS)

Rodriguez, C.; Baxter, A.; McEachern, D.; Venneri, F.; Williams, D.

2002-01-01

Helium-cooled, graphite-moderated reactors with ceramic-coated fuel particles offer unique advantages for the destruction of transuranic materials discharged in Light Water Reactor spent fuel. This is accomplished by fission, and capture-followed-by-fission processes. Three major features make it practical: (1) ceramic-coated particles accommodate high levels of burnup in one pass, thus reducing the need for repeated reprocessing; (2) graphite moderation produces valuable opportunities for thermal and epithermal neutrons to interact with fissionable and non-fissionable materials respectively; and (3) ceramic-coated particle kernel sizes can be adjusted to control the rate of such interactions. In the transmutation scheme proposed here, virtually complete destruction of weapons-usable materials, and 95% destruction of all transuranic waste is achieved. Higher levels of destruction are possible by repeated reprocessing and recycling, but there is little incentive to do so since each reprocessing step generates new secondary waste. After transmutation, the impervious ceramic-coated fuel particles provide an ideal residual waste form. (author)

4th Neutron Transmutation Doping Conference

CERN Document Server

1984-01-01

viii The growing use of NTD silicon outside the U. S. A. motivated an interest in having the next NTD conference in Europe. Therefore, the Third International Conference on Neutron Transmutation-Doped Silicon was organized by Jens Guldberg and held in Copenhagen, Denmark on August 27-29, 1980. The papers presented at this conference reviewed the developments which occurred during the t'A'O years since the previous conference and included papers on irradiation technology, radiation-induced defects, characteriza­ tion of NTD silicon, and the use of NTD silicon for device appli­ cations. The proceedings of this conference were edited by Jens Guldberg and published by Plenum Press in 1981. Interest in, and commercial use of, NTD silicon continued to grow after the Third NTD Conference, and research into neutron trans­ mutation doping of nonsilicon semiconductors had begun to accel­ erate. The Fourth International Transmutation Doping Conference reported in this volume includes invited papers summarizing the p...

Application of variance reduction technique to nuclear transmutation system driven by accelerator

Energy Technology Data Exchange (ETDEWEB)

Sasa, Toshinobu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-03-01

In Japan, it is the basic policy to dispose the high level radioactive waste arising from spent nuclear fuel in stable deep strata after glass solidification. If the useful elements in the waste can be separated and utilized, resources are effectively used, and it can be expected to guarantee high economical efficiency and safety in the disposal in strata. Japan Atomic Energy Research Institute proposed the hybrid type transmutation system, in which high intensity proton accelerator and subcritical fast core are combined, or the nuclear reactor which is optimized for the exclusive use for transmutation. The tungsten target, minor actinide nitride fuel transmutation system and the melted minor actinide chloride salt target fuel transmutation system are outlined. The conceptual figures of both systems are shown. As the method of analysis, Version 2.70 of Lahet Code System which was developed by Los Alamos National Laboratory in USA was adopted. In case of carrying out the analysis of accelerator-driven subcritical core in the energy range below 20 MeV, variance reduction technique must be applied. (K.I.)

Actinide partitioning-transmutation program final report. I. Overall assessment

International Nuclear Information System (INIS)

Croff, A.G.; Blomeke, J.O.; Finney, B.C.

1980-06-01

This report is concerned with an overall assessment of the feasibility of and incentives for partitioning (recovering) long-lived nuclides from fuel reprocessing and fuel refabrication plant radioactive wastes and transmuting them to shorter-lived or stable nuclides by neutron irradiation. The principal class of nuclides considered is the actinides, although a brief analysis is given of the partitioning and transmutation (P-T) of 99 Tc and 129 I. The results obtained in this program permit us to make a comparison of the impacts of waste management with and without actinide recovery and transmutation. Three major conclusions concerning technical feasibility can be drawn from the assessment: (1) actinide P-T is feasible, subject to the acceptability of fuels containing recycle actinides; (2) technetium P-T is feasible if satisfactory partitioning processes can be developed and satisfactory fuels identified (no studies have been made in this area); and (3) iodine P-T is marginally feasible at best because of the low transmutation rates, the high volatility, and the corrosiveness of iodine and iodine compounds. It was concluded on the basis of a very conservative repository risk analysis that there are no safety or cost incentives for actinide P-T. In fact, if nonradiological risks are included, the short-term risks of P-T exceed the long-term benefits integrated over a period of 1 million years. Incentives for technetium and iodine P-T exist only if extremely conservative long-term risk analyses are used. Further RD and D in support of P-T is not warranted

Development of neutron-transmutation-doped germanium bolometer material

International Nuclear Information System (INIS)

Palaio, N.P.

1983-08-01

The behavior of lattice defects generated as a result of the neutron-transmutation-doping of germanium was studied as a function of annealing conditions using deep level transient spectroscopy (DLTS) and mobility measurements. DLTS and variable temperature Hall effect were also used to measure the activation of dopant impurities formed during the transmutation process. In additioon, a semi-automated method of attaching wires on to small chips of germanium ( 3 ) for the fabrication of infrared detecting bolometers was developed. Finally, several different types of junction field effect transistors were tested for noise at room and low temperature (approx. 80 K) in order to find the optimum device available for first stage electronics in the bolometer signal amplification circuit

Transmutation of LWR waste actinides in thermal reactors

International Nuclear Information System (INIS)

Gorrell, T.C.

1979-01-01

Recycle of actinides to a reactor for transmutation to fission products is being considered as a possible means of waste disposal. Actinide transmutation calculations were made for two irradiation options in a thermal (LWR) reactor. The cases considered were: all actinides recycled in regular uranium fuel assemblies, and transuranic actinides recycled in separate mixed oxide (MOX) assemblies. When all actinides were recycled in a uranium lattice, a reduction of 62% in the transuranic inventory was achieved after 10 recycles, compared to the inventory accumulated without recycle. When the transuranics from 2 regular uranium assemblies were combined with those recycled from a MOX assembly, the transuranic inventory was reduced 50% after 5 recycles

Nickel Foil as Transmutation Detector for Neutron Fluence Measurements

Directory of Open Access Journals (Sweden)

Klupák Vít

2016-01-01

Full Text Available Activation detectors are very often used for determination of the neutron fluence in reactor dosimetry. However, there are few disadvantages concerning these detectors; it is the demand of the knowledge of the irradiation history and a loss of information due to a radioactive decay in time. Transmutation detectors TMD could be a solution in this case. The transmutation detectors are materials in which stable or long-lived nuclides are produced by nuclear reactions with neutrons. From a measurement of concentration of these nuclides, neutron fluence can be evaluated regardless of the cooling time.

Transmutation potential of current and innovative nuclear power systems

International Nuclear Information System (INIS)

Slessarev, I.; Salvatores, M.; Uematsu, M.

1993-01-01

In the present paper we have investigated the transmutation potential of different nuclear systems from a physical point of view. Transuranium (TRU) elements have been considered, but also long lived fission products (LLFP). The potential for transmutation has to take into account not only the consumption of a specific nucleus (or of a specific 'family' of nuclei), but also the reproduction of other nuclei of higher masses. The present study allows an intercomparison taking into account both aspects. Technological, safety and design constraints were not considered at this stage. However strategic indications for future studies have been obtained. 3 refs., 3 tabs

Subcritical molten salt reactor with fast/intermediate spectrum for minor actinides transmutation

International Nuclear Information System (INIS)

Degtyarev, Alexey M.; Feinberg, Olga S.; Kolyaskin, Oleg E.; Myasnikov, Andrey A.; Karmanov, Fedor I.; Kuznetsov, Andrey Yu.; Ponomarev, Leonid I.; Seregin, Mikhail B.; Sidorkin, Stanislav F.

2011-01-01

The subcritical molten-salt reactor for transmutation of Am and Cm with the fast-intermediate neutron spectrum is suggested. It is shown that ∼10 such reactor-burners is enough to support the future nuclear power based on the fast reactors as well as for the transmutation of Am and Cm accumulated in the spent fuel storages. (author)

The status of nuclear data for transmutation calculations

International Nuclear Information System (INIS)

Wilson, W.B.; England, T.R.; MacFarlane, R.E.; Muir, D.W.; Young, P.G.

1995-01-01

At this point, the accurate description of transmutation products in a radiation environment is more a nuclear data problem than a code development effort. We have used versions of the CINDER code for over three decades to describe the transmutation of nuclear reactor fuels in radiation environments. The need for the accurate description of reactor neutron-absorption, decay-power, and decay-spectra properties have driven many AEC, ERDA, and DOE supported nuclear data development efforts in this period. The level of cross-section, decay, and fission-yield data has evolved from rudimentary to a comprehensive ENDF/B-VI library permitting great precision in reactor calculations. The precision of the data supporting reactor simulations provides a sturdy foundation for the data base required for the wide range of transmutation problems currently studied. However, such reactor problems are typically limited to neutron energies below 10 MeV or so; reaction and decay data are required for actinides of, say, 90 ≤ Z ≤ 96 neutron-rich fission products of 22 ≤ Z ≤ 72. The expansion into reactor structural materials and fusion systems extends these ranges in energy and Z somewhat. The library of nuclear data, constantly growing in breadth and quality with international cooperation, is now described in the following table

PKA distributions: Contributions from transmutation products and from radioactive decay

Directory of Open Access Journals (Sweden)

M.R. Gilbert

2016-12-01

Full Text Available The neutrons generated in fusion plasmas interact with materials via nuclear reactions. The resulting transmutations and atomic displacements have life-limiting consequences for fusion reactor components. A detailed understanding of the production, evolution and material consequences of the damage created by cascades of atomic displacements requires, as a vital primary input, a complete description of the energy-spectrum of initial (prompt atomic displacement events (the primary knock on atoms or PKAs produced by direct neutron nuclear interactions. There is also the possibility that the radionuclides produced under transmutation will create further PKAs as they decay, and so the rate of these must also be quantified. This paper presents the latest results from the analysis of PKA spectra under neutron irradiation, focussing particularly on the variation in PKA distributions due to changes in composition under transmutation, but also on the PKA contributions from radioactive decay of materials that become activated under irradiation.

Partitioning and transmutation (P and D) 1995. A review of the current state of the art

International Nuclear Information System (INIS)

Skaalberg, M.; Landgren, A.; Spjuth, L.; Liljenzin, J.O.; Gudowski, W.

1995-12-01

The recent development in the field of partitioning and transmutation (P/T) is reviewed and evaluated. Current national and international R and D efforts are summarized. Nuclear transmutation with energy production is feasible in nuclear reactors where fast and thermal breeders are the most efficient for transmutation purposes. The operation of subcritical nuclear reactors by high current proton accelerators that generate neutrons in a spallation target is also an interesting option for transmutation and energy production, that has to be more carefully evaluated. These accelerator-driven systems are probably the only solution for the transmutation of long-lived fission products with small neutron capture cross sections and actinide isotopes with small fission cross sections. The requirements on the separation chemistry in the partitioning process depends on the transmutation strategy chosen. Recent developments in aqueous based separation chemistry opens some interesting possibilities to meet some of the requirements, such as separation of different actinides and some fission products and reduction of secondary waste streams. In the advanced accelerator-driven transmutation systems proposed, liquid fuels such as molten salts are considered. The partitioning processes that can be used for these types of fuel will, however, require a long term research program. The possibility to use centrifuge separation is an interesting partitioning option that recently has been proposed. 51 refs, 7 figs, 3 tabs

Nuclear waste transmutation

International Nuclear Information System (INIS)

Leray, S.

1995-01-01

Accelerators can play a role in the disposal of long-lived radioactive waste: an alternative to the storage in deep underground repositories might transmuting long-lived elements into stable or short-lived ones in subcritical systems driven by spallation neutrons. These neutrons would be produced by a high intensity, intermediate energy proton accelerator irradiating a heavy target. Similar systems have also been proposed to produce energy with a minimized waste inventory. Since a good knowledge of the spallation process is essential for designing and optimizing the target-blanket assembly, new programmes aimed at studying spallation reactions are in progress. (author). 6 figs

Evaluation of nuclides with closely spaced values of depletion constants in transmutation chains

International Nuclear Information System (INIS)

Vukadin, Z.S.

1977-01-01

New method of calculating nuclide concentrations in a transmutation chain is developed in this thesis. Method is based on originally derived recurrence formulas for expansion series of depletion functions and on originally obtained, nonsingular, Bateman coefficients. Explicit expression for the nuclide concentrations in a transmutation chain is obtained. This expression can be used as it stands for arbitrary values of nuclides depletion constants. By computing hypothetical transmutation chains and neptunium series, method is compared with the Bateman analytical solution, with the approximate solutions and with the matrix exponential method. It comes out that the method presented in this thesis is suitable for calculating very long depletion chains even in the case of some closely spaced and/or equal values of nuclide depletion constants. Though, presented method is of great practical applicability in a number of nuclear physics problems that are dealing with the nuclide transmutations: starting from the studies of the stellar evolution up to the design of nuclear reactors (author) [sr

Incentives and recent proposals for partitioning and transmutation in the United States

International Nuclear Information System (INIS)

Donovan, T.J.

1995-05-01

Partitioning and transmutation (P-T) is perhaps the most elegant means of high level waste disposal. Currently, the cost of fuel obtained from reprocessing spent fuel exceeds the cost of fuel obtained by mining. This has resulted in the once through fuel cycle dominating the US nuclear industry. Despite this fact P-T continues to be examined and debated by the US as well as abroad. The US first seriously considered P-T between approximately 1976 and 1982 but rejected the concept in favor of reprocessing. More recently, since about 1989, as a result of the once through fuel cycle and the growing problems of waste disposal, studies concerning P-T have resumed. This essay will seek to outline the incentives and goals of partitioning and transmutation as it would apply to the disposal of spent fuel in the US. Recent proposals by various US national laboratories for implementing partitioning and transmutation as a high level waste management and disposal device will also be discussed. The review will seek to examine the technical concepts utilized in each of the proposals and their feasibility. The major focus of this essay will be the transmutation methods themselves, while the partitioning methods will be discussed only briefly. This is because of the fact that partitioning methods fall under reprocessing as an already fairly well established and accepted technology while feasible methods for transmutation are still being advanced

Comparative study of accelerator driven system (ADS) of different transmutation scenarios for actinides in advanced nuclear fuel cycles

International Nuclear Information System (INIS)

Embid-Segura, M.; Gonzalez Romero, M.E.; Perez Parra, A.

2001-01-01

The full text follows. In recent years transmutation has raised as a complementary option to solve the problem of the long-lived radioactive waste produced in nuclear power plants. The main advantages expected from transmutation are the reduction in volume of the high level waste and a significant decrease in the long-term radiotoxicity inventory, with a probable impact in the final costs and potential risks of the geological repository. This paper will describe the evaluation of different systems proposed for actinide transmutation, their integration in the waste management process, their viability, performances and limitations. Particular attention is taking of comparing transmutation scenarios where the actinides are transmuted inside fertile (U, Th) or inert matrix. This study has been supported by ENRESA inside the CIEMAT-ENRESA collaboration for the study of long-lived isotope transmutation. (authors)

Use of fast reactors for actinide transmutation

International Nuclear Information System (INIS)

1993-03-01

The management of radioactive waste is one of the key issues in today's discussions on nuclear energy, especially the long term disposal of high level radioactive wastes. The recycling of plutonium in liquid metal fast breeder reactors (LMFBRs) would allow 'burning' of the associated extremely long life transuranic waste, particularly actinides, thus reducing the required isolation time for high level waste from tens of thousands of years to hundreds of years for fission products only. The International Working Group on Fast Reactors (IWGFR) decided to include the topic of actinide transmutation in liquid metal fast breeder reactors in its programme. The IAEA organized the Specialists Meeting on Use of Fast Breeder Reactors for Actinide Transmutation in Obninsk, Russian Federation, from 22 to 24 September 1992. The specialists agree that future progress in solving transmutation problems could be achieved by improvements in: Radiochemical partitioning and extraction of the actinides from the spent fuel (at least 98% for Np and Cm and 99.9% for Pu and Am isotopes); technological research and development on the design, fabrication and irradiation of the minor actinides (MAs) containing fuels; nuclear constants measurement and evaluation (selective cross-sections, fission fragments yields, delayed neutron parameters) especially for MA burners; demonstration of the feasibility of the safe and economic MA burner cores; knowledge of the impact of maximum tolerable amount of rare earths in americium containing fuels. Refs, figs and tabs

MYRRHA. An experimental ADS Facility for Research and Development

International Nuclear Information System (INIS)

Ait Abderrahim, H.

2006-01-01

Full text of publication follows: Since 1998, SCK-CEN in partnership with IBA s.a. and many European research laboratories, is designing a multipurpose ADS for R and D applications MYRRHA - and is conducting an associated R and D support programme. MYRRHA is an Accelerator Driven System (ADS) under development at Mol in Belgium and aiming to serve as a basis for the European experimental ADS to provide protons and neutrons for various R and D applications. It consists of a proton accelerator delivering a 350 MeV * 5 mA proton beam to a liquid Pb-Bi spallation target that in turn couples to a Pb-Bi cooled, subcritical fast core. In a first stage, the project focuses mainly on demonstration of the ADS concept, safety research on sub-critical systems and nuclear waste transmutation studies. In a later stage, the device will also be dedicated to research on structural materials, nuclear fuel, liquid metal technology and associated aspects and on sub-critical reactor physics. Subsequently, it will be used as fast spectrum irradiation facility and as radioisotope production facility. Along the above design features, the MYRRHA project team is developing the MYRRHA project as a multipurpose irradiation facility for R and D applications on the basis of an Accelerator Driven System (ADS). The project is intended to fit into the European strategy towards an ADS Demo facility for nuclear waste transmutation as described in the PDS-XADS FP5 Project. As such it should serve the following task catalogue: ADS concept demonstration, Safety studies for ADS, MA transmutation studies, LLFP transmutation studies, Medical radioisotopes, Material research, Fuel research. A first preliminary conceptual design file of MYRRHA was completed by the end of 2001 and has been reviewed by an International Technical Guidance Committee that concluded that there are no show stoppers in the project even thought some topics such as the safety studies and the fuel qualification need to be addressed

Method to Reduce Long-lived Fission Products by Nuclear Transmutations with Fast Spectrum Reactors.

Science.gov (United States)

Chiba, Satoshi; Wakabayashi, Toshio; Tachi, Yoshiaki; Takaki, Naoyuki; Terashima, Atsunori; Okumura, Shin; Yoshida, Tadashi

2017-10-24

Transmutation of long-lived fission products (LLFPs: 79 Se, 93 Zr, 99 Tc, 107 Pd, 129 I, and 135 Cs) into short-lived or non-radioactive nuclides by fast neutron spectrum reactors without isotope separation has been proposed as a solution to the problem of radioactive wastes disposal. Despite investigation of many methods, such transmutation remains technologically difficult. To establish an effective and efficient transmutation system, we propose a novel neutron moderator material, yttrium deuteride (YD 2 ), to soften the neutron spectrum leaking from the reactor core. Neutron energy spectra and effective half-lives of LLFPs, transmutation rates, and support ratios were evaluated with the continuous-energy Monte Carlo code MVP-II/MVP-BURN and the JENDL-4.0 cross section library. With the YD 2 moderator in the radial blanket and shield regions, effective half-lives drastically decreased from 106 to 102 years and the support ratios reached 1.0 for all six LLFPs. This successful development and implementation of a transmutation system for LLFPs without isotope separation contributes to a the ability of fast spectrum reactors to reduce radioactive waste by consuming their own LLFPs.

An improved transmutation method for quantitative determination of the components in multicomponent overlapping chromatograms.

Science.gov (United States)

Shao, Xueguang; Yu, Zhengliang; Ma, Chaoxiong

2004-06-01

An improved method is proposed for the quantitative determination of multicomponent overlapping chromatograms based on a known transmutation method. To overcome the main limitation of the transmutation method caused by the oscillation generated in the transmutation process, two techniques--wavelet transform smoothing and the cubic spline interpolation for reducing data points--were adopted, and a new criterion was also developed. By using the proposed algorithm, the oscillation can be suppressed effectively, and quantitative determination of the components in both the simulated and experimental overlapping chromatograms is successfully obtained.

Study of an optimal configuration of a transmutation reactor based on a low-aspect-ratio tokamak

Energy Technology Data Exchange (ETDEWEB)

Hong, Bong Guen, E-mail: bghong@jbnu.ac.kr [Department of Quantum System Engineering, Chonbuk National University, 567 Baekje-daero, Jeonju, Jeonbuk 54896 (Korea, Republic of); Kim, Hoseok [Department of Applied Plasma Engineering, Chonbuk National University, 567 Baekje-daero, Jeonju, Jeonbuk 54896 (Korea, Republic of)

2016-11-15

Highlights: • Optimum configuration of a transmutation reactor based on a low aspect ratio tokamak was found. • Inboard and outboard radial build are determined by plasma physics, engineering and neutronics constraints. • Radial build and equilibrium fuel cycle play a major role in determining the transmutation characteristics. - Abstract: We determine the optimal configuration of a transmutation reactor based on a low-aspect-ratio tokamak. For self-consistent determination of the radial build of the reactor components, we couple a tokamak systems analysis with a radiation transport calculation. The inboard radial build of the reactor components is obtained from plasma physics and engineering constraints, while outboard radial builds are mainly determined by constraints on neutron multiplication, the tritium-breeding ratio, and the power density. We show that the breeding blanket model has an effect on the radial build of a transmutation blanket. A burn cycle has to be determined to keep the fast neutron fluence plasma-facing material below its radiation damage limit. We show that the radial build of the transmutation reactor components and the equilibrium fuel cycle play a major role in determining the transmutation characteristics.

Ma and LLFP transmutation in MTPs and ADSs: the typical SCK.CEN case of transmutations in BR2 and Myrrha. Position with respect to the global needs

International Nuclear Information System (INIS)

Raedt, Ch. de; Verboomen, B.; Aoust, Th.; Malambu, E.; Beeckmans de West-Meerbeeck, A.; Kupschus, P.; Benoit, Ph.; Ait Abderrahim, H.; Baetsle, L.H.

2001-01-01

The proposed paper indicates the performances, in the domain of the transmutation of MAs and LLFPs, of the high flux materials testing reactor BR2 located at SCK-CEN, and compares them with those of the multipurpose ADS MYRRHA, the pre-design of which is at the present time being finalized at SCK-CEN. With thermal neutron fluxes reaching 9.10 14 n/cm 2 s in thermal positions and 4.10 14 n/cm 2 s in the reactor core and, in the latter position, a fast flux (E>0.1 MeV) of 7.10 14 n/cm 2 s, BR2 has a transmutation throughput of the order of 1.5 kg Np+Am per 200 EFPD. This capacity can be used for investigating at the technological scale the transmutation of MAs and LLFPs in a thermal neutron spectrum with a high contribution of epithermal and fast neutrons. The metallurgical behaviour of the targets can hence be studied. In MYRRHA, higher fast fluxes are expected to be attained in irradiation positions near the spallation source, viz fast fluxes (E>0.75 MeV) up to 10. 15 n/cm 2 s. One of the purposes of MYRRHA is therefore its utilisation for the investigation of actinide transmutation feasibility with ADSs. (author)

Neutronics-processing interface analyses for the Accelerator Transmutation of Waste (ATW) aqueous-based blanket system

International Nuclear Information System (INIS)

Davidson, J.W.; Battat, M.E.

1993-01-01

Neutronics-processing interface parameters have large impacts on the neutron economy and transmutation performance of an aqueous-based Accelerator Transmutation of Waste (ATW) system. A detailed assessment of the interdependence of these blanket neutronic and chemical processing parameters has been performed. Neutronic performance analyses require that neutron transport calculations for the ATW blanket systems be fully coupled with the blanket processing and include all neutron absorptions in candidate waste nuclides as well as in fission and transmutation products. The effects of processing rates, flux levels, flux spectra, and external-to-blanket inventories on blanket neutronic performance were determined. In addition, the inventories and isotopics in the various subsystems were also calculated for various actinide and long-lived fission product transmutation strategies

Conceptual study on high performance blanket in a spherical tokamak fusion-driven transmuter

International Nuclear Information System (INIS)

Chen Yixue; Wu Yican

2000-01-01

A preliminary conceptual design on high performance dual-cooled blanket of fusion-driven transmuter is presented based on neutronic calculation. The dual-cooled system has some attractive advantages when utilized in transmutation of HLW (High Level Wastes). The calculation results show that this kind of blanket could safely transmute about 6 ton minor actinides (produced by 170 GW(e) Year PWRs approximately) and 0.4 ton fission products per year, and output 12 GW thermal power. In addition, the variation of power and critical factor of this blanket is relatively little during its 1-year operation period. This blanket is also tritium self-sustainable

Fuel design for the U.S. accelerator driven transmutation system

International Nuclear Information System (INIS)

Meyer, M. K.; Hayes, S. L.; Crawford, D. C.; Pahl, R. G.; Tsai, H.

2002-01-01

The U.S. concept for actinide transmutation is currently envisioned as a system to destroy plutonium as well as minor actinides in a single or two tier system. In order to maximize the actinide destruction rate, an inert matrix fuel is used. The effectiveness of transmutation in reducing the actinide inventory is linked to the development of a robust fuel system, capable of achieving very high burnup. Very little fuel performance data has been generated to date on inert matrix systems, and there are several issues specific to the behavior of higher actinides that do not allow extension of the existing uranium-plutonium fuel database to these new fuels. These issues include helium production, fuel-cladding-chemical-interaction, and americium migration. In the early 1990's, two U-Pu-Zr metal alloy fuel elements containing 1.2 wt.% Am and 1.3 wt.% Np were fabricated and irradiated to approximately 6 at.% burnup in the Experimental Breeder Reactor-II. Postirradiation examination results were not published; however the recent interest in fuel for actinide transmutation has prompted a reexamination of this data. The results of the postirradiation examination of this experiment, including gas sampling, metallography, and gamma scanning are discussed. Available data on inert matrix fuels and other fuels incorporating actinides are used to assess the implications of minor-actinide specific issues on transmuter fuel. Considerations for the design of nitride and oxide fuels, metallic fuels, and metal-matrix dispersion fuels are discussed

Promises and Challenges of Thorium Implementation for Transuranic Transmutation - 13550

Energy Technology Data Exchange (ETDEWEB)

Franceschini, F.; Lahoda, E.; Wenner, M. [Westinghouse Electric Company LLC, Cranberry Township, PA (United States); Lindley, B. [University of Cambridge (United Kingdom); Fiorina, C. [Polytechnic of Milan (Italy); Phillips, C. [Energy Solutions, Richland, WA (United States)

2013-07-01

This paper focuses on the challenges of implementing a thorium fuel cycle for recycle and transmutation of long-lived actinide components from used nuclear fuel. A multi-stage reactor system is proposed; the first stage consists of current UO{sub 2} once-through LWRs supplying transuranic isotopes that are continuously recycled and burned in second stage reactors in either a uranium (U) or thorium (Th) carrier. The second stage reactors considered for the analysis are Reduced Moderation Pressurized Water Reactors (RMPWRs), reconfigured from current PWR core designs, and Fast Reactors (FRs) with a burner core design. While both RMPWRs and FRs can in principle be employed, each reactor and associated technology has pros and cons. FRs have unmatched flexibility and transmutation efficiency. RMPWRs have higher fuel manufacturing and reprocessing requirements, but may represent a cheaper solution and the opportunity for a shorter time to licensing and deployment. All options require substantial developments in manufacturing, due to the high radiation field, and reprocessing, due to the very high actinide recovery ratio to elicit the claimed radiotoxicity reduction. Th reduces the number of transmutation reactors, and is required to enable a viable RMPWR design, but presents additional challenges on manufacturing and reprocessing. The tradeoff between the various options does not make the choice obvious. Moreover, without an overarching supporting policy in place, the costly and challenging technologies required inherently discourage industrialization of any transmutation scheme, regardless of the adoption of U or Th. (authors)

Fuel Design for the U.S. Accelerator Driven Transmutation System

International Nuclear Information System (INIS)

Meyer, M.K.; Hayes, S.L.; Crawford, D.C.; Pahl, R.G.; Tsai, H.

2002-01-01

The U.S. concept for actinide transmutation is currently envisioned as a system to destroy plutonium as well as minor actinides in a single or two tier system. In order to maximize the actinide destruction rate, an inert matrix fuel is used. The effectiveness of transmutation in reducing the actinide inventory is linked to the development of a robust fuel system, capable of achieving very high burnup. Very little fuel performance data has been generated to date on inert matrix systems, and there are several issues specific to the behavior of higher actinides that do not allow extension of the existing uranium-plutonium fuel database to these new fuels. These issues include helium production, fuel-cladding-chemical-interaction, and americium migration. In the early 1990's, two U-Pu-Zr metal alloy fuel elements containing 1.2 wt.% Am and 1.3 wt.% Np were fabricated and irradiated to approximately 6 at.% burnup in the Experimental Breeder Reactor-II. Postirradiation examination results were not published; however the recent interest in fuel for actinide transmutation has prompted a reexamination of this data. The results of the postirradiation examination of this experiment, including gas sampling, metallography, and gamma scanning are discussed. Available data on inert matrix fuels and other fuels incorporating actinides are used to assess the implications of minor-actinide specific issues on transmuter fuel. Considerations for the design of nitride and oxide fuels, metallic fuels, and metal-matrix dispersion fuels are discussed. (authors)

Evidence for the occurrence of LENR-type processes in alchemic transmutations

Energy Technology Data Exchange (ETDEWEB)

Perez-Pariente, Joaquin [Instituto de Catalisis y Petroleoquimica, CSIC, Marie Curie 2, 28049 Cantoblanco, Madrid (Spain)

2006-07-01

The relevance of experimental aspects of alchemy have been neglected for too long in the academic milieu, but in recent years more thoughtful studies of texts from the middle ages and early modern European alchemy evidence the presence of coherent and relevant laboratory practices. However, the central core of western alchemy, the quest for the Philosophers' Stone, the substance claimed to transmute base metals into gold, remains, needless to say, elusive. While no book will ever tell us how to prepare such substance, it is nevertheless also true that detailed reports on alchemic transmutations, often authored by witnesses of such events, can be found profusely in alchemic literature. These reports usually contain valuable information regarding quantitative aspects of the transmutation processes. Taking into account numerical parameters of alchemic transmutations such as the weights of starting base metal, gold and Philosophers' Stone, and the duration of the transmutation experiences, it has been found that the transmutation processes follow a specific pattern similar to that generally observed in conventional catalytic reactions. In the present work, several examples of alchemic practices and objects are reported that, taken as a whole, challenge our actual view on the constitution of matter. First, new data are presented which support the catalytic-like performance of the Philosophers' Stone. Indeed, such behaviour is consistent with the alchemic view on the evolution of metals, which conceives the transmutation as an acceleration of the ripening of base metals towards the more perfect gold which takes place in Nature by means of a slow maturation process inside the Earth's womb. Second, differences between the weight of the starting base metal and the weight of the gold (or silver) obtained at the end of the transmutation process are often noticed in the texts, but no satisfactory explanation for such observation has been given so far

Evidence for the occurrence of LENR-type processes in alchemic transmutations

International Nuclear Information System (INIS)

Perez-Pariente, Joaquin

2006-01-01

The relevance of experimental aspects of alchemy have been neglected for too long in the academic milieu, but in recent years more thoughtful studies of texts from the middle ages and early modern European alchemy evidence the presence of coherent and relevant laboratory practices. However, the central core of western alchemy, the quest for the Philosophers' Stone, the substance claimed to transmute base metals into gold, remains, needless to say, elusive. While no book will ever tell us how to prepare such substance, it is nevertheless also true that detailed reports on alchemic transmutations, often authored by witnesses of such events, can be found profusely in alchemic literature. These reports usually contain valuable information regarding quantitative aspects of the transmutation processes. Taking into account numerical parameters of alchemic transmutations such as the weights of starting base metal, gold and Philosophers' Stone, and the duration of the transmutation experiences, it has been found that the transmutation processes follow a specific pattern similar to that generally observed in conventional catalytic reactions. In the present work, several examples of alchemic practices and objects are reported that, taken as a whole, challenge our actual view on the constitution of matter. First, new data are presented which support the catalytic-like performance of the Philosophers' Stone. Indeed, such behaviour is consistent with the alchemic view on the evolution of metals, which conceives the transmutation as an acceleration of the ripening of base metals towards the more perfect gold which takes place in Nature by means of a slow maturation process inside the Earth's womb. Second, differences between the weight of the starting base metal and the weight of the gold (or silver) obtained at the end of the transmutation process are often noticed in the texts, but no satisfactory explanation for such observation has been given so far. Weight decreases are

Transmutation of minor actinide using BWR fueled mixed oxide

International Nuclear Information System (INIS)

Susilo, Jati

2000-01-01

Nuclear spent fuel recycle has a strategic importance in the aspect of nuclear fuel economy and prevention of its spread-out. One among other application of recycle is to produce mixed oxide fuel (Mo) namely mixed Plutonium and uranium oxide. As for decreasing the burden of nuclear high level waste (HLW) treatment, transmutation of minor actinide (MA) that has very long half life will be carried out by conversion technique in nuclear reactor. The purpose of this study was to know influence of transition fuel cell regarding the percent weight of transmutation MA in the BWR fueled MOX. Calculation of cell BWR was used SRAC computer code, with assume that the reactor in equilibrium. The percent weight of transmutation MA to be optimum by increasing the discharge burn-up of nuclear fuel, raising ratio of moderator to fuel volume (Vm/Vf), and loading MA with percent weight about 3%-6% and also reducing amount of percent weight Pu in MOX fuel. For mixed fuel standard reactor, reactivity value were obtained between about -50pcm ∼ -230pcm for void coefficient and -1.8pcm ∼ -2.6pcm for fuel temperature coefficient

First results and future trends for the transmutation of long-lived radioactive wastes

International Nuclear Information System (INIS)

Prunier, C.; Salvatores, M.; Guerin, Y.; Zaetta, A.

1993-01-01

In the frame of the CEA SPIN program, a project has been set-up at the Direction of Nuclear Reactors of CEA, to study the transmutation of long-lived radioactive products (both minor actinides and fission products) resulting from the operation of current nuclear power plants. The program is focused on: transmutation in minor actinides (Np, Am) in fission reactors of known technology (both of the PWR or the fast reactor type), using the so-called ''homogeneous'' (mixed with Uranium or Uranium-Plutonium), and ''heterogeneous'' (mixed with inert matrices) recycling modes for both type of reactors. Transmutation studies in dedicated devices (both fission reactors with actinide/plutonium fuel or with high thermal flux, and particle accelerator-based systems). Fuel studies related to both homogeneous and heterogeneous recycling modes in fission reactors. For the homogeneous recycling mode, some experimental irradiations results are available from past PHENIX programs. For the heterogeneous mode, very limited experimental results are available, and new theoretical and experimental work is underway on the use of appropriate inert matrices. Basic data studies to assess the quality of existing nuclear data for fission reactor transmutation studies, future data needs of relevance, and model/data developments needed for accelerator-based systems. Strategy studies, to evaluate the consequences of the different transmutation options on the fuel cycle, according to different scenarios of nuclear power development. 7 refs., 3 figs., 5 tabs

System and safety studies of accelerator driven transmutation systems. Annual report 1998

International Nuclear Information System (INIS)

Wallenius, J.; Gudowski, W.; Carlsson, Johan; Eriksson, Marcus; Tucek, K.

1998-12-01

This annual report describes the accelerator-driven transmutation project conducted at the Department of Nuclear and Reactor Physics at the Royal Institute of Technology. The main results are: development of the simulation tools for accelerator-driven transmutation calculations including an integrated Monte-Carlo burnup module and improvements of neutron energy fission yield simulations, processing of the evacuated nuclear data files including preparation of the temperature dependent neutron cross-sections, development of nuclear data for a medium energy range for some isotopes, development of the models and codes for radiation damage simulations, system studies for the spent fuel transmuter, based on heavy metal coolant and advanced nuclear fuel, contribution to the spallation target design being manufactured in IPPE, Obninsk, and accelerator reliability studies. Moreover a lot of efforts were put to further develop existing international collaboration with the most active research groups in the world together with educational activities in Sweden including a number of meetings and workshops and a graduate course in transmutation. This project has been conducted in close collaboration with the EU-project 'Impact of the accelerator based technologies on nuclear fission safety' - IABAT and in bilateral cooperation with different foreign research groups

System and safety studies of accelerator driven transmutation systems. Annual report 1998

Energy Technology Data Exchange (ETDEWEB)

Wallenius, J.; Gudowski, W.; Carlsson, Johan; Eriksson, Marcus; Tucek, K. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

1998-12-01

This annual report describes the accelerator-driven transmutation project conducted at the Department of Nuclear and Reactor Physics at the Royal Institute of Technology. The main results are: development of the simulation tools for accelerator-driven transmutation calculations including an integrated Monte-Carlo burnup module and improvements of neutron energy fission yield simulations, processing of the evacuated nuclear data files including preparation of the temperature dependent neutron cross-sections, development of nuclear data for a medium energy range for some isotopes, development of the models and codes for radiation damage simulations, system studies for the spent fuel transmuter, based on heavy metal coolant and advanced nuclear fuel, contribution to the spallation target design being manufactured in IPPE, Obninsk, and accelerator reliability studies. Moreover a lot of efforts were put to further develop existing international collaboration with the most active research groups in the world together with educational activities in Sweden including a number of meetings and workshops and a graduate course in transmutation. This project has been conducted in close collaboration with the EU-project `Impact of the accelerator based technologies on nuclear fission safety` - IABAT and in bilateral cooperation with different foreign research groups 31 refs, 23 figs

Neutronics design for a spherical tokamak fusion-transmutation reactor

International Nuclear Information System (INIS)

Deng Meigen; Feng Kaiming; Yang Bangchao

2002-01-01

Based on studies of the spherical tokamak fusion reactors, a concept of fusion-transmutation reactor is put forward. By using the one-dimension transport and burn-up code BISON3.0 to process optimized design, a set of plasma parameters and blanket configuration suitable for the transmutation of MA (Minor Actinides) nuclear waste is selected. Based on the one-dimension calculation, two-dimension calculation has been carried out by using two-dimension neutronics code TWODANT. Combined with the neutron flux given by TWODANT calculation, burn-up calculation has been processed by using the one-dimension radioactivity calculation code FDKR and some useful and reasonable results are obtained

Safety techniques in the change of nuclear systems. Radiation protection at spallation neutron sources and transmutation facilities

International Nuclear Information System (INIS)

Nuenighoff, Kay

2009-01-01

To push the boundary towards higher neutron fluxes concepts based on spallation reactions have been discussed. Here neutrons are produced by bombarding a heavy metal target (e.g. mercury, tungsten, or tantalum) with high energetic protons. Up to now such facilities could not be realised because of the high power particle accelerators needed. Recent developments of the accelerator technology open the possibility of construction and operating proton accelerators in the MW region. This is demonstrated by construction and commissioning of two MW spallation neutron sources, namely SNS (Oak Ridge, Tennessee, USA) with a power of 1.4 MW and J-PARC (Japan) with 1 MW. The realisation of proton accelerators at this power level will open the way towards energy amplifiers, as proposed e.g. by Carlo Rubbia. Such a facility will not only produce electric power. Furthermore longliving radionuclides can be transmutated into shortlived or even stable nuclides by neutron induced nuclear reactions. A mitigation of the problem of nuclear waste disposal. The above discussed developments prove that accelerators are not only constructed for research, moreover application of these technology became state of the art. With the emergence of particle accelerators in the MW region, radiation protection is confronted with new kind of problems to be solved. Especially the higher kinetic energies of the primary beam particles requires modification and expansion of computer programs well known in nuclear engineering. In contrast to nuclear reactors with kinetic energies up to 2-3 MeV, in spallation reaction secondary particles up to the incident energy in the GeV region will be produced. Problems related to radiation protection have to be considered in an energy range three orders of magnitude higher than known from nuclear reactors. In this thesis existing computer codes are compared and validated with data from selected experiments. Questions concerning radiation protection covers a broad range

Spent Nuclear Fuel Option Study on Hybrid Reactor for Waste Transmutation

International Nuclear Information System (INIS)

Hong, Seong Hee; Kim, Myung Hyun

2016-01-01

DUPIC nuclear fuel can be used in hybrid reactor by compensation of subcritical level through (U-10Zr) fuel. Energy production performance of Hyb-WT with DUPIC is grateful because it has high EM factor and performs waste transmutation at the same time. However, waste transmutation performance should be improved by different fissile fuel instead of (U-10Zr) fuel. SNF (Spent Nuclear Fuel) disposal is one of the problems in the nuclear industry. FFHR (Fusion-Fission Hybrid Reactor) is one of the most attractive option on reuse of SNF as a waste transmutation system. Because subcritical system like FFHR has some advantages compared to critical system. Subcritical systems have higher safety potential than critical system. Also, there is suppressed excess reactivity at BOC (Beginning of Cycle) in critical system, on the other hand there is no suppressed reactivity in subcritical system. Our research team could have designed FFHR for waste transmutation; Hyb-WT. Various researches have been conducted on fuel and coolant option for optimization of transmutation performance. However, Hyb-WT has technical disadvantage. It is required fusion power (Pfus) which is the key design parameter in FFHR is increased for compensation of decreasing subcritical level. As a result, structure material integrity is damaged under high irradiation condition by increasing Pfus. Also, deep burn of reprocessed SNF is limited by weakened integrity of structure material. Therefore, in this research, SNF option study will be conducted on DUPIC (Direct Use of Spent PWR Fuel in CANDU Reactor) fuel, TRU fuel and DUPIC + TRU mixed fuel for optimization of Hyb-WT performance. Goal of this research is design check for low required fusion power and high waste transmutation. In this paper, neutronic analysis is conducted on Hyb-WT with DUPIC nuclear fuel. When DUPIC nuclear fuel is loaded in fast neutron system, supplement fissile materials need to be loaded together for compensation of low criticality

Spent Nuclear Fuel Option Study on Hybrid Reactor for Waste Transmutation

Energy Technology Data Exchange (ETDEWEB)

Hong, Seong Hee; Kim, Myung Hyun [Kyung Hee University, Yongin (Korea, Republic of)

2016-05-15

DUPIC nuclear fuel can be used in hybrid reactor by compensation of subcritical level through (U-10Zr) fuel. Energy production performance of Hyb-WT with DUPIC is grateful because it has high EM factor and performs waste transmutation at the same time. However, waste transmutation performance should be improved by different fissile fuel instead of (U-10Zr) fuel. SNF (Spent Nuclear Fuel) disposal is one of the problems in the nuclear industry. FFHR (Fusion-Fission Hybrid Reactor) is one of the most attractive option on reuse of SNF as a waste transmutation system. Because subcritical system like FFHR has some advantages compared to critical system. Subcritical systems have higher safety potential than critical system. Also, there is suppressed excess reactivity at BOC (Beginning of Cycle) in critical system, on the other hand there is no suppressed reactivity in subcritical system. Our research team could have designed FFHR for waste transmutation; Hyb-WT. Various researches have been conducted on fuel and coolant option for optimization of transmutation performance. However, Hyb-WT has technical disadvantage. It is required fusion power (Pfus) which is the key design parameter in FFHR is increased for compensation of decreasing subcritical level. As a result, structure material integrity is damaged under high irradiation condition by increasing Pfus. Also, deep burn of reprocessed SNF is limited by weakened integrity of structure material. Therefore, in this research, SNF option study will be conducted on DUPIC (Direct Use of Spent PWR Fuel in CANDU Reactor) fuel, TRU fuel and DUPIC + TRU mixed fuel for optimization of Hyb-WT performance. Goal of this research is design check for low required fusion power and high waste transmutation. In this paper, neutronic analysis is conducted on Hyb-WT with DUPIC nuclear fuel. When DUPIC nuclear fuel is loaded in fast neutron system, supplement fissile materials need to be loaded together for compensation of low criticality

Transmutation of sup 2 sup 0 sup 4 Pb in an intensive gamma-ray flux

CERN Document Server

Ishkhanov, B S

2001-01-01

Transmutation chain formation during irradiation with various intensities of bremsstrahlung photon beam is analysed. The main features of transmutation chain formation by photons with energies corresponding to the giant dipole resonance are discussed.

On the use of spinel-based nuclear fuels for the transmutation of actinides

International Nuclear Information System (INIS)

Konings, R.J.M.; Bakker, K.; Boshoven, J.G.; Hein, H.; Huntelaar, M.E.; Zhang, H.; Meeldijk, J.D.; Woensdregt, C.F.

1997-01-01

The properties of spinel-based nuclear fuels for the transmutation of actinides are investigated. The results of laboratory experiments, thermodynamic calculations and irradiations in the High Flux Reactor (HFR) at Petten are presented, and allow us to evaluate the potential of spinel as an inert matrix for fuels and targets for transmutation. (author)

Legal and regulatory issues regarding classification and disposal of wastes from actinide partitioning and transmutation

International Nuclear Information System (INIS)

Kocher, D.C.

1989-01-01

Partitioning and transmutation of actinide radioelements in spent nuclear fuel from civilian power reactors is potentially attractive because the resulting wastes might be acceptable for disposal using systems which are considerably less costly than a deep geologic repository. At present, there are no legal or regulatory prohibitions to seeking alternatives to a geologic repository for disposal of such wastes. However, additional laws and regulations would be needed, and the Nuclear Regulatory Commission has been reluctant to alter the current framework for radioactive waste management, in which geologic repositories or near-surface facilities are the only disposal options established in law and regulations unless a compelling need for alternatives with intermediate waste-isolation capabilities is demonstrated. There are also important technical considerations which are not encouraging with regard to the development of intermediate disposal systems for wastes from partitioning and transmutation of actinides in civilian spent fuel. First, the wastes may contain sufficient concentrations of fission products. Second, defense reprocessing wastes may contain sufficient concentrations of fission products and long-lived actinides. Thus, in developing the legal and regulatory framework for alternative disposal systems, there is a need to establish maximum concentrations of fission products and long-lived actinides that would be acceptable for intermediate disposal. 19 refs

Study on partitioning and transmutation (P and T) of high-level waste. Status of R and D. Final report; Studie zur Partitionierung und Transmutation (P and T) hochradioaktiver Abfaelle. Stand der Grundlagen- und technologischen Forschung. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Merk, Bruno; Glivici-Cotruta, Varvara

2014-07-01

The main project, where this sub project contributed to, has been structured into two modules: module A (funded by the federal ministry of economics, managed by KIT) and module B (funded by the federal ministry of education and research, managed by acatech). Partners in module A were DBE TECHNOLOGY GmbH, the Gesellschaft fuer Anlagen- und Reaktorsicherheit mbH (GRS), the Helmholtz-Zentrum Dresden-Rossendorf (HZDR), the Karlsruher Institute of Technology (KIT) and the Rheinisch-Westfaelische Technische Hochschule (RWTH) Aachen, in co-operation with the Forschungszentrum Juelich (FZJ). Modul B has been executed by the Zentrum fuer Interdisziplinaere Risiko- und Innovationsforschung der Universitaet Stuttgart (ZIRIUS). The overall coordination has been carried out by the Deutsche Akademie der Technikwissenschaften (acatech). The social implications have been evaluated in module B based on the analysis of the scientific and technological aspects in module A. Recommendations for communication and actions to be taken for the future positioning of P and T have been developed. In the project part, coordinated by HZDR - status of R and D - an overview on the whole topic P and T is given. The topic is opened by a short description of reactor systems possible for transmutation. In the following the R and D status of separation technologies, safety technology, accelerator technology, liquid metal technology, spallation target development, transmutation fuel and structural material development, as well as waste conditioning is described. The topic is completed by the specifics of transmutation systems, the basic physics and core designs, the reactor physics, the simulation tools and the development of Safety Approaches. Additionally, the status of existing irradiation facilities with fast neutron spectrum is described. Based on the current R and D status, the research and technology gaps in the topics: separation and conditioning, accelerator and spallation target, and reactor

Partitioning and Transmutation. Annual Report 2006

Energy Technology Data Exchange (ETDEWEB)

Dubois, Isabelle; Englund, Sofie; Fermvik, Anna; Liljenzin, Jan-Olov; Neumayer, Denis; Retegan, Teodora; Skarnemark, Gunnar [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Chemical and Biological Engineering

2007-01-15

The long-lived elements in the spent nuclear fuels are mostly actinides, some fission products ({sup 79}Se, {sup 87}Rb, {sup 99}Tc, {sup 107}Pd, {sup 126}Sn, {sup 129}I, {sup 135}Cs) and activation products ({sup 14}C, {sup 36}Cl, {sup 59}Ni, {sup 93} Zr, {sup 94} To be able to destroy the long-lived elements in a transmutation process they must be separated from the rest of the spent nuclear fuel. The most difficult separations to make are those between trivalent actinides and lanthanides, due to their relatively similar chemical properties, and those between different actinides themselves. These separations are necessary to obtain the desired efficiency of the transmutation process and in order not to create any unnecessary waste thus rendering the process useless. Solvent extraction is an efficient and well-known method that makes it possible to have separation factors that fulfil the highly set demands on purity of the separated phases and on small losses. Chalmers University of Technology is involved in research regarding the separation of actinides and lanthanides and between the actinides themselves as a partner in the EUROPART project within the European Union sixth framework program. This is a continuation of the projects we participated in within the fourth and fifth framework programmes, NEWPART and PARTNEW, respectively. The aims of the projects have now shifted from basic understanding to more applied research with focus on process development. However, since the basic understanding is still needed we have our main focus on the chemical processes and understanding of how they work. Work is progressing in relation to a proposal for the 7th framework programme. This proposal will be aiming at a pilot plant for separation for transmutation purposes.

Transmutation of long-lived nuclides

International Nuclear Information System (INIS)

Liang Tongxiang; Tang Chunhe

2003-01-01

Partitioning and transmutation of long-lived nuclides have profound benefits for economic development, global political stability and the environment. This technology would reduce nuclear waste disposal requirements, prevent proliferation and eliminate a major hurdle to the development of nuclear power. This paper reviews the advanced fuel cycle process and development of ATW in the world, and some suggestions about the R and D of nuclear power in China are proposed

Evaluation of the transmutation of transuranic using neutrons spectrum from the spallation reaction

Energy Technology Data Exchange (ETDEWEB)

Gilberti, Mauricio; Pereira, Claubia, E-mail: mgilber@eletronuclear.gov.br [Eletrobras Termonuclear S.A. (ELETRONUCLEAR), Angra dos Reis, RJ (Brazil); Veloso, Maria A. Fortini, E-mail: claubia@nuclear.ufmg.br [Universidade Federal de Minas Gerais (UFMG), Belo Horizante, MG (Brazil). Dept. de Engenharia Nuclear

2013-07-01

The transmutation of transuranic was analyzed by simulating the neutron flux from different spallation sources across arrays of fissile material with isotopic composition PWR reprocessing. A simplified model of Accelerator-Driven Systems (ADS) containing target, moderator graphite, lead-bismuth coolant or sodium coolant, is used. The simulation was made using the particles transport code MCNPX 2.6.0 which allowed to evaluate the rate of transmutation of actinides (Np, Pu, Am, and Cm) at different locations in the system. The objective of the study is to evaluate which the behavior and influences the spectrum of the spallation in the transmutation without the contribution or interference of multiplier, medium subcritical, which would add the contribution of fission neutrons generated, thus interfering in the analysis. The arrangement enable to infer the influence of hardened neutron flux from the spallation reaction in the transmutation, the results show that this is independent of the target material chosen, and the spectrum of spallation has a negligible importance compared to the influence of moderation and scattering generated by the coolant or moderator used. (author)

Evaluation of the transmutation of transuranic using neutrons spectrum from the spallation reaction

International Nuclear Information System (INIS)

Gilberti, Mauricio; Pereira, Claubia; Veloso, Maria A. Fortini

2013-01-01

The transmutation of transuranic was analyzed by simulating the neutron flux from different spallation sources across arrays of fissile material with isotopic composition PWR reprocessing. A simplified model of Accelerator-Driven Systems (ADS) containing target, moderator graphite, lead-bismuth coolant or sodium coolant, is used. The simulation was made using the particles transport code MCNPX 2.6.0 which allowed to evaluate the rate of transmutation of actinides (Np, Pu, Am, and Cm) at different locations in the system. The objective of the study is to evaluate which the behavior and influences the spectrum of the spallation in the transmutation without the contribution or interference of multiplier, medium subcritical, which would add the contribution of fission neutrons generated, thus interfering in the analysis. The arrangement enable to infer the influence of hardened neutron flux from the spallation reaction in the transmutation, the results show that this is independent of the target material chosen, and the spectrum of spallation has a negligible importance compared to the influence of moderation and scattering generated by the coolant or moderator used. (author)

System study on partitioning and transmutation of long-lived isotopes

International Nuclear Information System (INIS)

Szieberth, M.

2001-01-01

The management of long-lived isotopes - transuranium elements and fission products - produced in nuclear reactors is a problem that substantially affects the public acceptance of nuclear energy, and may influence the long-term hazard caused by energy production. Partitioning and transmutation of spent fuel materials offer a suitable solution to this problem. After the nuclear community had realised this fact, the number of publications on this topic significantly increased but there is still a lack of studies that include the analysis of not only one instrument but also the whole nuclear energy system. However, from the viewpoint of Partitioning and transmutation's implementation a substantial question is the cooperation of plants optimised for energy generation and others for partitioning or transmutation. In order to analyse this problem, the schemes of different systems are framed and their mathematical models are worked out. The systems are evaluated through the long-term risks caused by the waste deposited in final disposal, and the risks are described by a newly defined quantity, the residual hazard index. (author)

An assessment of partition and transmutation against UK requirements for radioactive waste management

International Nuclear Information System (INIS)

Cummings, R.; Bush, R.P.; Crookshanks, C.E.

1996-06-01

A review of partition and transmutation is made with the objective of assessing the prospects for real financial of safety gains being made from the future use of partition and transmutation within the UK. The assessment covers all the civil high-level waste (HLW) from reprocessing spent fuel, civil spent fuels where there are currently no plans or contracts for reprocessing, and intermediate-level waste (ILW). Both existing stocks and future arisings are included. The impact is also analysed of considering all the non-military uranium and plutonium extant in the UK as candidates for transmutation. The assessment takes full account of advances in technology since the earlier UK studies and changes in the UK situation. (Author)

Transmutation of nuclear waste. Status report RAS programme 1993: Recycling and transmutation of actinides and fission products

Energy Technology Data Exchange (ETDEWEB)

Abrahams, K; Bultman, J H; Cordfunke, E H.P.; Gruppelaar, H; Janssen, A J; Franken, W M.P.; Klippel, K T; Kloosterman, J L; Konings, R J.M.; Smit, J

1994-11-01

The term ``nuclear transmutation`` means a conversion of long-lived radioactive nuclides into short-lived or stable nuclides and ``recycling`` means re-use of fissile material to generate energy in power reactors. With these two processes a reduction of the radiotoxicity and of its duration may be achieved, thus reducing the potential hazard to future generations. Firstly, the report gives a survey of the present situation regarding nuclear waste: its components, how the waste is produced in current LWR and possible options for interim and final storage. Then the objective of the RAS programme, the working methods and the state of the art of the research are considered. Two chapters deal with preliminary results of national and international research. A rather tentative prediction for the future is formulated. Some conclusions are drawn: It seems to be in the best interests of the Netherlands to continue the established line of reprocessing nuclear waste, should new reactors be introduced. It may be advisable to make international agreements so that in the future fission products will contain as few traces of transuranic actinides and long-lived components as possible. Consequently, nuclear waste would become cleaner in terms of long-lived components. For the transmutation of products separated in foreign countries, the Netherlands could pursue an active policy, perform research and also consider the use of MOX fuel in future Dutch reactors. Further contributions towards the solution of these problems can only be made by the Netherlands on an international level. As such, the research and study performed within the framework of the RAS-programme represents a useful international contribution. Finally, the choice of a new generation of nuclear reactors should be made not based only on the safety aspects, but also on the extent of waste production and on the transmutation possibilities (application of MOX, etc.). (orig./HP).

System and safety studies of accelerator driven systems for transmutation. Annual report 2007

International Nuclear Information System (INIS)

Arzhanov, Vasily; Fokau, Andrei; Persson, Calle; Runevall, Odd; Sandberg, Nils; Tesinsky, Milan; Wallenius, Janne; Youpeng Zhang

2008-05-01

Within the project 'System and safety studies of accelerator driven systems for transmutation', research on design and safety of sub-critical reactors for recycling of minor actinides is performed. During 2007, the reactor physics division at KTH has calculated safety parameters for EFIT-400 with cermet fuel, permitting to start the transient safety analysis. The accuracy of different reactivity meters applied to the YALINA facility was assessed and neutron detection studies were performed. A model to address deviations from point kinetic behaviour was developed. Studies of basic radiation damage physics included calculations of vacancy formation and activation enthalpies in bcc niobium. In order to predict the oxygen potential of inert matrix fuels, a thermo-chemical model for mixed actinide oxides was implemented in a phase equilibrium code

Advanced separation and transmutation, long dated behavior of vitrified wastes: 15 years of scientific researches; Separation poussee et transmutation, comportement a long terme des dechets vitrifies: 15 ans d'avancees scientifiques

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-02-15

This report presents the results after 15 years of researches at the Cea, concerning the separation and transmutation of radioactive wastes and the conditioning and the long time storage of wastes at the surface. These researches were asked in the framework of the Bataille law. The first part devoted to the transmutation and separation of ling life radioactive elements presents the challenges, the advanced separation, the transmutation and the evaluation of the researches. The second part devoted to the long dated storage discusses the high activity wastes vitrification, the behavior of the vitrified wastes packages after thousand years, the international researches and the evaluation of the researches. (A.L.B.)

Helium and fission gas behaviour in magnesium aluminate spinel and zirconia for actinide transmutation

NARCIS (Netherlands)

Damen, P.M.G.

2003-01-01

In order to reduce the long-term radiotoxicity of spent nuclear fuel, many studies are performed on partitioning and transmutation of actinides. In such a scenario, the long-lived radio-isotopes (mostly actinides) are partitioned from the nuclear waste, and subsequently transmuted or fissioned in a

Transmuted of Rayleigh Distribution with Estimation and Application on Noise Signal

Science.gov (United States)

Ahmed, Suhad; Qasim, Zainab

2018-05-01

This paper deals with transforming one parameter Rayleigh distribution, into transmuted probability distribution through introducing a new parameter (λ), since this studied distribution is necessary in representing signal data distribution and failure data model the value of this transmuted parameter |λ| ≤ 1, is also estimated as well as the original parameter (⊖) by methods of moments and maximum likelihood using different sample size (n=25, 50, 75, 100) and comparing the results of estimation by statistical measure (mean square error, MSE).

EFTTRA, a European collaboration for the development of fuels and targets for the transmutation

International Nuclear Information System (INIS)

Babelot, J.F.; Muehling, G.; Prunier, C.; Rome, M.

1994-12-01

In the frame of the research programmes on the transmutation of long lived nuclides, many experimental or theoretical investigations have to be carried out within European collaborations, owing mainly to the costs of such studies. Therefore, a group named 'Experimental Feasibility of Targets for Transmutation' (EFTTRA), has been formed, with participants from CEA (France). ECN (The Netherlands), EDF (France), KFK (Germany) and ITU (European Commission), to organise joint experiments for the study of materials for the transmutation. So far, it was decided to focus the work on the transmutation of 99 Tc (metal), of 129 I (compound), and of Am (in an inert matrix). Irradiations will take place in parallel in the Phenix fast reactor in France, and in the high flux thermal reactor HFR in the Netherlands. These experiments, together with the related post-irradiation examinations, constitute the first phase of the EFTTRA collaboration. In subsequent phases, EFTTRA will contribute to the development of fuels and targets. (orig.)

Physics and safety of transmutation systems. A status report

International Nuclear Information System (INIS)

2006-01-01

The safe and efficient management of spent fuel from the operation of commercial nuclear power plants is an important issue. Worldwide, more than 250 000 tons of spent fuel from currently operating reactors will require disposal. These numbers account for only high-level radioactive waste generated by present-day power reactors. Nearly all issues related to risks to future generations arising from the long-term disposal of such spent nuclear fuel is attributable to only about 1% of its content. This 1% is made up primarily of plutonium, neptunium, americium and curium (called transuranic elements) and the long-lived isotopes of iodine and technetium.When transuranics are removed from discharged fuel destined for disposal, the toxic nature of the spent fuel drops below that of natural uranium ore (that which was originally mined for the nuclear fuel) within a period of several hundred to a thousand years. This significantly reduces the burden on geological repositories and the problem of addressing the remaining long-term residues can thus de done in controlled environments having timescales of centuries rather than millennia stretching beyond 10 000 years. Transmutation is one of the means being explored to address the disposal of transuranic elements. To achieve this, advanced reactors systems, appropriate fuels, separation techniques and associated fuel cycle strategies are required. This status report begins by providing a clear definition of partitioning and transmutation (P and T), and then describes the state of the art concerning the challenges facing the implementation of P and T, scenario studies and specific issues related to accelerator-driven systems (ADS) dynamics and safety, long-lived fission product transmutation and the impact of nuclear data uncertainty on transmutation system design. The report will be of particular interest to nuclear scientists working on P and T issues as well as advanced fuel cycles in general. (author)

Transmutation of Americium in Light and Heavy Water Reactors

Energy Technology Data Exchange (ETDEWEB)

Hyland, B.; Dyck, G.R.; Edwards, G.W.R. [Chalk River Laboratories, Atomic Energy of Canada Limited (Canada); Ellis, R.J.; Gehin, J.C. [Oak Ridge National Laboratory (ORNL), Oak Ridge, Tennessee (United States); Maldonado, G.I. [University of Tennessee (Knoxville)/ORNL, Tennessee (United States)

2009-06-15

There is interest worldwide in reducing the burden on geological nuclear fuel disposal sites. In most disposal scenarios the decay heat loading of the surrounding rock limits the capacity of these sites. On the long term, this decay heat is generated primarily by actinides, and a major contributor 100 to 1000 years after discharge from the reactor is {sup 241}Am. One possible approach to reducing the decay-heat burden is to reprocess spent reactor fuel and use thermal spectrum reactors to 'burn' the Am nuclides. The viability of this approach is dependent upon the detailed changes in chemical and isotopic composition of actinide-bearing fuels after irradiation in thermal reactor spectra. The currently available thermal spectrum reactor options include light water-reactors (LWRs) and heavy-water reactors (HWRs) such as the CANDU{sup R} designs. In addition, as a result of the recycle of spent LWR fuel, there would be a considerable amount of potential recycled uranium (RU). One proposed solution for the recycled uranium is to use it as fuel in Candu reactors. This paper investigates the possibilities of transmuting americium in 'spiked' bundles in pressurized water reactors (PWRs) and in boiling water reactors (BWRs). Transmutation of Am in Candu reactors is also examined. One scenario studies a full core fuelled with homogeneous bundles of Am mixed with recycled uranium, while a second scenario places Am in an inert matrix in target channels in a Candu reactor, with the rest of the reactor fuelled with RU. A comparison of the transmutation in LWRs and HWRs is made, in terms of the fraction of Am that is transmuted and the impact on the decay heat of the spent nuclear fuel. CANDU{sup R} is a registered trademark of Atomic Energy of Canada Limited (AECL). (authors)

Transmutation and activation of fusion reactor wall and structural materials

International Nuclear Information System (INIS)

Jarvis, O.N.

1979-01-01

This report details the extent of the nuclear data needed for inclusion in a data library to be used for general assessments of fusion reactor structure activation and transmutation, describes the sources of data available, reviews the literature and explores the reliability of current calculations by providing an independent assessment of the activity inventory to be expected from five structural materials in a simple blanket design for comparison with the results of other workers. An indication of the nuclear reactions which make important contributions to the activity, transmutation and gas production rates for these structural materials is also presented. (author)

An assessment of partition and transmutation against UK requirements for radioactive waste management: supporting studies

International Nuclear Information System (INIS)

Cummings, R.; Crookshanks, C.E.; McAdams, R.; Rogers, J.M.; Sims, H.E.; Smith-Briggs, J.L.

1996-06-01

A study of partition and transmutation (P and T) has recently been reported: An Assessment of Partition and Transmutation Against UK Requirements for Radioactive Waste Management (DOE/RAS/96.007). The prospects were assessed for real safety or financial gains being made through the future use of partition and transmutation within the United Kingdom in radioactive waste management. The assessment was made by AEA Technology, on behalf of the Department of the Environment. The assessment was partly based on the results of a number of studies described here. (Author)

Partitioning and transmutation. Current developments - 2010. A report from the Swedish reference group for PT-research

Energy Technology Data Exchange (ETDEWEB)

Blomgren, Jan (ed.) (Swedish Centre for Nuclear Technology, SKC, Stockholm (Sweden)); Karlsson, Fred (Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)); Pomp, Stephan (Uppsala Univ., Uppsala, Dept. of Physics and Astronomy, Div. of Applied Nuclear Physics (Sweden)); Aneheim, Emma; Ekberg, Christian; Fermvik, Anna; Skarnemark, Gunnar (Nuclear Chemistry, Dept. of Chemical and Biological Engineering, Chalmers Univ. of Technology, Goeteborg (Sweden)); Wallenius, Janne; Zakova, Jitka (Reactor Physics Div., Physics Dept., Royal Inst. of Technology, Stockholm (Sweden)); Grenthe, Ingemar; Szabo, Zoltan (School of Chemical Science and Engineering, Royal Inst. of Technology, Stockholm (Sweden))

2010-01-15

The research and development on methods for partitioning and transmutation (P and T) of long-lived radionuclides in spent nuclear fuel has attracted considerable interest during the last decade. The main objective of P and T is to eliminate or at least substantially reduce the amount of such long-lived radionuclides that has to go to a deep geological repository for final disposal. The objective of current research on partitioning is to find and develop processes suitable for separation of the heavier actinides (and possibly some long-lived fission products) on an industrial scale. The objective of current research on transmutation is to define, investigate and develop facilities that may be suitable for transmutation of the long-lived radionuclides. The research on partitioning has made important progress in recent years. In some cases one has succeeded to separate americium and curium. Many challenges remain however. Within hydrochemistry one has achieved sufficiently good distribution and separation factors. The focus turns now towards development of an operating process. The search for ligands that give sufficiently good extraction and separation will continue but with less intensity. The emphasis will rather be on improving stability against hydrolysis and radiolysis. This may be achieved either by additives to the solvent or by selection of a proper solvent. The development of processes and equipment must be intensified. Pyrochemical research is looking into methods for recovery of uranium and for separating fission products with large neutron cross sections. The objective is to avoid separation of plutonium from other transuranium elements and thus simplify the proliferation issue. The future work is focused on improved selectivity and on technical development. Design of processes and equipment is difficult due to the aggressive properties of the melts and the relatively high temperatures required. The fabrication of fuel for transmutation and the

Partitioning and transmutation. Current developments - 2010. A report from the Swedish reference group for PT-research

International Nuclear Information System (INIS)

Blomgren, Jan; Karlsson, Fred; Pomp, Stephan; Aneheim, Emma; Ekberg, Christian; Fermvik, Anna; Skarnemark, Gunnar; Wallenius, Janne; Zakova, Jitka; Grenthe, Ingemar; Szabo, Zoltan

2010-01-01

The research and development on methods for partitioning and transmutation (P and T) of long-lived radionuclides in spent nuclear fuel has attracted considerable interest during the last decade. The main objective of P and T is to eliminate or at least substantially reduce the amount of such long-lived radionuclides that has to go to a deep geological repository for final disposal. The objective of current research on partitioning is to find and develop processes suitable for separation of the heavier actinides (and possibly some long-lived fission products) on an industrial scale. The objective of current research on transmutation is to define, investigate and develop facilities that may be suitable for transmutation of the long-lived radionuclides. The research on partitioning has made important progress in recent years. In some cases one has succeeded to separate americium and curium. Many challenges remain however. Within hydrochemistry one has achieved sufficiently good distribution and separation factors. The focus turns now towards development of an operating process. The search for ligands that give sufficiently good extraction and separation will continue but with less intensity. The emphasis will rather be on improving stability against hydrolysis and radiolysis. This may be achieved either by additives to the solvent or by selection of a proper solvent. The development of processes and equipment must be intensified. Pyrochemical research is looking into methods for recovery of uranium and for separating fission products with large neutron cross sections. The objective is to avoid separation of plutonium from other transuranium elements and thus simplify the proliferation issue. The future work is focused on improved selectivity and on technical development. Design of processes and equipment is difficult due to the aggressive properties of the melts and the relatively high temperatures required. The fabrication of fuel for transmutation and the

Transmutation Strategy Using Thorium-Reprocessed Fuel ADS for Future Reactors in Vietnam

Directory of Open Access Journals (Sweden)

Thanh Mai Vu

2013-01-01

Full Text Available Nuclear power is believed to be a key to the energy security for a developing country like Vietnam where the power demanding increases rapidly every year. Nevertheless, spent nuclear fuel from nuclear power plants is the source of radiotoxic and proliferation risk. A conceptual design of ADS utilizing thorium fuel as a based fuel and reprocessed fuel as a seed for nuclear waste transmutation and energy production is proposed as one of the clean, safe, and economical solutions for the problem. In the design, 96 seed assemblies and 84 blanket assemblies were inserted into the core to make a heterogeneous subcritical core configuration. Introducing thorium fuel into the core offers an effective way to transmute plutonium and minor actinide (MA and gain energy from this process. Transmutation rate as a function of burnup is estimated using MCNPX 2.7.0 code. Results show that by using the seed-blanket designed ADS, at 40 GWd/t burnup, 192 kg of plutonium and 156 kg of MA can be eliminated. Equivalently, 1  ADS can be able to transmute the transuranic (TRU waste from 2  LWRs. 14 units of ADS would be required to eliminate TRUs from the future reactors to be constructed in Vietnam.

Analysis of advanced European nuclear fuel cycle scenarios including transmutation and economical estimates

International Nuclear Information System (INIS)

Merino Rodriguez, I.; Alvarez-Velarde, F.; Martin-Fuertes, F.

2013-01-01

Four European fuel cycle scenarios involving transmutation options have been addressed from a point of view of resources utilization and economics. Scenarios include the current fleet using Light Water Reactor (LWR) technology and open fuel cycle (as a reference scenario), a full replacement of the initial fleet with Fast Reactors (FR) burning U-Pu MOX fuel and two fuel cycles with Minor Actinide (MA) transmutation in a fraction of the FR fleet or in dedicated Accelerator Driven Systems (ADS).Results reveal that all scenarios are feasible according to nuclear resources demand. Regarding the economic analysis, the estimations show an increase of LCOE - averaged over the whole period - with respect to the reference scenario of 20% for Pu management scenario and around 35% for both transmutation scenarios respectively.

Analysis of advanced European nuclear fuel cycle scenarios including transmutation and economical estimates

Energy Technology Data Exchange (ETDEWEB)

Merino Rodriguez, I.; Alvarez-Velarde, F.; Martin-Fuertes, F.

2013-07-01

Four European fuel cycle scenarios involving transmutation options have been addressed from a point of view of resources utilization and economics. Scenarios include the current fleet using Light Water Reactor (LWR) technology and open fuel cycle (as a reference scenario), a full replacement of the initial fleet with Fast Reactors (FR) burning U-Pu MOX fuel and two fuel cycles with Minor Actinide (MA) transmutation in a fraction of the FR fleet or in dedicated Accelerator Driven Systems (ADS).Results reveal that all scenarios are feasible according to nuclear resources demand. Regarding the economic analysis, the estimations show an increase of LCOE - averaged over the whole period - with respect to the reference scenario of 20% for Pu management scenario and around 35% for both transmutation scenarios respectively.

Progress on the Application of Metallic Fuels for Actinide Transmutation

International Nuclear Information System (INIS)

Kennedy, J. Rory; Fielding, Randall; Janney, Dawn; Mariani, Robert; Teague, Melissa; Egeland, Gerald

2015-01-01

Full text of publication follows: Idaho National Laboratory (INL) is developing actinide bearing alloy metallic fuels intended for effecting the transmutation of long-lived isotopes in fast reactor application as part of a partitioning and transmutation strategy. This presentation will report on progress in three areas of this effort: demonstration of the fabrication of fuels under remote (hot cell) conditions directly coupled to the product from the Pyro-processing of spent fuel as part of the Joint Fuel Cycle Studies (JFCS) collaboration with the Korean Atomic Energy Research Institute (KAERI); the chemical sequestration of lanthanide fission products to mitigate fuel-cladding-chemical-interaction (FCCI); and transmission electron microscopy (TEM) and atom probe tomography (APT) studies on the as-cast microstructure of the metallic fuel alloy. For the JFCS efforts, we report on the implementation of the Glove-box Advanced Casting System (GACS) as a prototype casting furnace for eventual installation into the INL Hot Fuel Examination Facility (HFEF) where the recycled fuel will be cast. Results from optimising process parameters with respect to fuel characteristics, americium volatility, materials interaction, and lanthanide fission product carry over distribution will be discussed. With respect to the lanthanide carry over from the Pyro-processing product, encouraging studies on concepts to chemically sequester the FCCI promoting lanthanides within the fuel matrix thus inhibiting migration and interaction with the cladding will be presented. Finally, in relation to advanced modelling and simulation efforts, detailed investigations and interpretation on the nano-scale as cast microstructure of possible recycle fuel composition containing U, Pu, Am, Np as well as carry-over lanthanide species will be discussed. These studies are important for establishing the initial conditions from which advanced physics based fuel performance codes will run. (authors)

Development of long-lived radionuclide transmutation technology - Development of a code system for core analysis of the transmutation reactors

Energy Technology Data Exchange (ETDEWEB)

Cho, Nam Zin; Kim, Yong Hee; Kim, Tae Hyung; Jo, Chang Keun; Park, Chang Je [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

1996-07-01

The objective of this study is to develop a code system for core analysis= of the critical transmutation reactors utilizing fast neutrons. Core characteristics of the transmutation reactors were identified and four codes, HANCELL for pincell calculation, PRISM and AFEN-H3D for core calculation, and MA{sub B}URN for depletion calculation, were developed. The pincell calculation code is based on one-dimensional collision probability method and may provide homogenized/condensed parameters of a pincell and also can homogenize the control assembly via a nonlinear iterative method. The core calculation codes, PRISM and AFEN-H3D, solve the multi-group, multi-dimensional neutron diffusion equations for a hexagonal geometry and they are based on the finite difference method and analytic function expansion nodal (AFEN) method, respectively. The MA{sub B}URN code san analyze the behavior of actinides and fission products in a reactor core. Through benchmarking, we confirmed that the newly developed codes provide accurate solutions. 30 refs., 10 tabs., 8 figs. (author)

Transmutation prospect of long-lived nuclear waste induced by high-charge electron beam from laser plasma accelerator

Science.gov (United States)

Wang, X. L.; Xu, Z. Y.; Luo, W.; Lu, H. Y.; Zhu, Z. C.; Yan, X. Q.

2017-09-01

Photo-transmutation of long-lived nuclear waste induced by a high-charge relativistic electron beam (e-beam) from a laser plasma accelerator is demonstrated. A collimated relativistic e-beam with a high charge of approximately 100 nC is produced from high-intensity laser interaction with near-critical-density (NCD) plasma. Such e-beam impinges on a high-Z convertor and then radiates energetic bremsstrahlung photons with flux approaching 1011 per laser shot. Taking a long-lived radionuclide 126Sn as an example, the resulting transmutation reaction yield is the order of 109 per laser shot, which is two orders of magnitude higher than obtained from previous studies. It is found that at lower densities, a tightly focused laser irradiating relatively longer NCD plasmas can effectively enhance the transmutation efficiency. Furthermore, the photo-transmutation is generalized by considering mixed-nuclide waste samples, which suggests that the laser-accelerated high-charge e-beam could be an efficient tool to transmute long-lived nuclear waste.

Neutron transmutation doping of gallium arsenide

International Nuclear Information System (INIS)

Alexiev, D.

1987-12-01

Neutron transmutation doping (NTD) was studied as a means of compensating p-type Cd-doped GaAs. By introducing specific donor concentrations, the net acceptor level was measured and showed a progressive reduction. The NTD constant K = 0.32 donor atoms.cm 3 per cm 2 was also measured. Radiation damage caused by neutron bombardment was annealed and no additional traps were generated

Transmutation Fuels Campaign FY-09 Accomplishments Report

Energy Technology Data Exchange (ETDEWEB)

Lori Braase

2009-09-01

This report summarizes the fiscal year 2009 (FY-08) accomplishments for the Transmutation Fuels Campaign (TFC). The emphasis is on the accomplishments and relevance of the work. Detailed description of the methods used to achieve the highlighted results and the associated support tasks are not included in this report.

Nudatra: nuclear data for transmutation in IP-Eurotrans

International Nuclear Information System (INIS)

Gonzalez, E.M.; Koning, A.; Leray, S.; Plompen, A.; Sanz, J.

2007-01-01

The objective of NUDATRA, Domain 5 of the EU Integrated Project EUROTRANS (FI6W-CT-2004- 516520), is to improve and validate the nuclear data and simulation tools required for the development and optimisation of nuclear waste transmutation, ADS dedicated transmutation systems and the associated fuel cycle. Activities are essentially aimed at supplementing the evaluated nuclear data libraries and improving the reaction models for materials in transmutation fuels, coolants, spallation targets, internal structures, and reactor and accelerator shielding, relevant for the design and optimisation of the ETD and XT-ADS. These activities are distributed over four Work Packages: Sensitivity Analysis and Validation of Nuclear Data and Simulation Tools; Low- and Intermediate-energy Nuclear Data Measurements; Nuclear Data Libraries Evaluation and Low-intermediate Energy Models; and High-energy Experiments and Modelling.The main accomplishments expected from NUDATRA are: 1) new measurements and evaluations of Pb-Bi cross-sections, i.e. inelastic, (n,xn) and isomer branching ratios (Po production); 2) new measurements and evaluations for minor actinides particularly the capture in 243 Am and fission on 244 Cm; 3) improvement of TALYS as an evaluation tool and as an a priori model for the estimation of low- and intermediate-energy reaction cross-section; 4) high-energy model improvement based on measurements, particularly for the prediction of the spallation products, and gas (H, He) production cross-sections; 5) sensitivity and uncertainty analysis of ETD fuel cycle and related covariance issues. (authors)

The nuclear design optimization of a Pb-Bi alloy cooled transmuter, PEACER-300

International Nuclear Information System (INIS)

Lim, Jae-Yong; Kim, Myung-Hyun

2006-01-01

A core design of lead-bismuth cooled fast reactor, PEACER-300 has been investigated to maximize its transmutation capability within safety criteria. Transmutation of minor actinide under a closed recycling was analyzed with assumption on decontamination factors in pyro-reprocessing plant data at reasonably high values. To acquire high transmutation performance, feed fuel composition, P/D ratio, active core height and fuel cycle strategy were changed. For preventing the fuel meting and guaranteeing long plant life-time, the number of fuel assembly array and normal operation temperature were decided. The optimized design parameter were chosen as of a flat core shape with 50 cm of active core height and 5 m core diameter, loaded with 17 x 17 arrayed fuel assemblies. A pitch to diameter ratio is 2.2, operating coolant temperature range is 300 deg. C to 400 deg. C, and core consists of 3 different enrichment zones with one year cycle length. Performance of designed core showed a high transmutation capability with support ratio of 2.085, large negative temperature feedback coefficients, and sufficient shutdown margin with 28 B 4 C control assemblies. (authors)

Transmutation technologies to solve the problem of long-term spent nuclear fuel storage

International Nuclear Information System (INIS)

Hosnedl, P.; Valenta, V.; Blahut, O.

2000-01-01

The paper gives a brief description of the transmutation process for actinides and long-lived fission products which are present in spent nuclear fuel. Transmutation technologies can solve the problem of long-term spent nuclear fuel storage and reduce the requirements for storage time and conditions. The basic data and requirements for the detailed design of the transmutor are summarized, and the views upon how to address the fuel purification and dry reprocessing issues are discussed. The results of activities of SKODA JS are highlighted; these include, for instance, the fluoride salt-resistant material MONICR, test loops, and electrowinners. The preliminary design of the transmutor is also outlined. Brief information regarding activities in the field of transmutation technologies in the Czech Republic and worldwide is also presented. The research and design activities to be developed for the whole design of the demonstration and basic units are summarized. It is emphasized that SKODA JS can join in international cooperation without constraints. The Attachment presents a simple assessment of how the radioactivity balance can be reduced, based on the actinide and long-lived fission product transmutation half-lives, is presented in the Attachment. (author)

Neutronic Analysis on Coolant Options in a Hybrid Reactor System for High Level Waste Transmutation

Energy Technology Data Exchange (ETDEWEB)

Hong, Seong Hee; Kim, Myung Hyun [Kyung Hee University, Seoul (Korea, Republic of)

2014-10-15

A fusion-fission hybrid reactor (FFHR) which is a combination of plasma fusion tokamak as a fast neutron source and a fission reactor as of fusion blanket is another potential candidate. In FFHR, fusion plasma machine can supply high neutron-rich and energetic 14.1MeV (D, T) neutrons compared to other options. Therefore it has better capability in HLW incineration. While, it has lower requirements compared to pure fusion. Much smaller-sized tokamak can be achievable in a near term because it needs relatively low plasma condition. FFHR has also higher safety potential than fast reactors just as ADSR because it is subcritical reactor system. FFHR proposed up to this time has many design concepts depending on the design purpose. FFHR may also satisfy many design requirement such as energy multiplication, tritium production, radiation shielding for magnets, fissile breeding for self-sustain ability also waste transmutation. Many types of fuel compositions and coolant options have been studied. Effect of choices for fuel and coolant was studied for the transmutation purpose FFHR by our team. In this study LiPb coolant was better than pure Li coolant both for neutron multiplication and tritium breeding. However, performance of waste transmutation was reduced with increased neutron absorption at coolant caused by tritium breeding. Also, LiPb as metal coolant has a problem of massive MHD pressure drop in coolant channels. Therefore, in a previous study, waste transmutation performance was evaluated with light water coolant option which may be a realistic choice. In this study, a neutronic analysis was done for the various coolant options with a detailed computation. One of solutions suggested is to use the pressure tubes inside of first wall and second wall In this work, performance of radioactive waste transmutation was compared with various coolant options. On the whole, keff increases with all coolants except for FLiBe, therefore required fusion power is decreased. In

Actinide and fission product partitioning and transmutation. Status and assessment report

International Nuclear Information System (INIS)

1999-01-01

Implementation and partitioning technology is intended to reduce the inventory of actinides and long-lived fission products in nuclear waste. Such technology can decrease hazards of pre-disposal waste management and of physical disturbance of a waste repository. An authoritative analysis is given of the technical, radiological and economic consequences of the proposed partitioning and transmutation operations on the present and future fuel cycle options. The report is subdivided to a general part for non-specialist readers, and to a technical systems analysis discussing issues on partitioning, transmutation and long-term waste management. (R.P.)

Feasibility analysis of constant TRU feeding in waste transmutation system using accelerator-driven subcritical system

Energy Technology Data Exchange (ETDEWEB)

Lee, Kun Jai; Cho, Nam Zin; Jo, Chang Keun; Park, Chang Je; Kim, Do Sam; Park, Jeong Hwan [Korea Advanced Institute of Science and Technology, Taejon (Korea)

1999-03-01

It is probable that the issue of nuclear spent fuel and high-level waste can have negative impact on the future expansion of nuclear power programs. Accelerator-driven nuclear waste transmutation with constant composition TRU feeding which satisfies non-proliferation condition will help establish the long-range nuclear waste disposal strategy. In this study, current status of accelerator-driven transmutation of waste technology, and feasibility analysis of constant composition TRU feeding system were investigated. We ascertained that solid system using constant composition TRU is feasible with the the capability of transmutation. (author). 13 refs., 53 figs., 20 tabs.

Planning and reporting of Russian transmutation research projects within ISTC. Phase 1

Energy Technology Data Exchange (ETDEWEB)

Conde, H. [Uppsala Univ., (Sweden). Dept. of Neutron Research; Gudowski, W. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Reactor Technology; Liljenzin, J.O. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Chemistry; Mileikovsky, C. [Pully (Switzerland)

1997-02-01

The International Scientific and Technical Center (ISTC) in Moscow funds research of civil interest to counteract the risk of nuclear weapon proliferation. Recently, new technical concepts, Accelerator Transmutation of Nuclear Waste (ATW), have been proposed to incinerate and transmute long-lived radioactive nuclear waste to relax the time needed to store the waste in a geological repository. The Russian experts are knowledgeable and well equipped for doing research in the different technical fields of relevance for the transmutation concepts. Thus, a number of ISTC projects have been proposed to investigate different technical aspects of ATW with a result that a fair number of former weapon specialists have converted from military to peaceful civilian research. The present report describes the back ground, the status and near term activities of a few ISTC projects of relevance for the ATW concept, which are planned with the participation of a Swedish reference group. 4 refs.

Planning and reporting of Russian transmutation research projects within ISTC. Phase 1

International Nuclear Information System (INIS)

Conde, H.

1997-02-01

The International Scientific and Technical Center (ISTC) in Moscow funds research of civil interest to counteract the risk of nuclear weapon proliferation. Recently, new technical concepts, Accelerator Transmutation of Nuclear Waste (ATW), have been proposed to incinerate and transmute long-lived radioactive nuclear waste to relax the time needed to store the waste in a geological repository. The Russian experts are knowledgeable and well equipped for doing research in the different technical fields of relevance for the transmutation concepts. Thus, a number of ISTC projects have been proposed to investigate different technical aspects of ATW with a result that a fair number of former weapon specialists have converted from military to peaceful civilian research. The present report describes the back ground, the status and near term activities of a few ISTC projects of relevance for the ATW concept, which are planned with the participation of a Swedish reference group. 4 refs

System and safety studies of accelerator driven transmutation. Annual Report 2003

International Nuclear Information System (INIS)

Gudowski, Waclaw; Wallenius, Jan; Tucek, Kamil

2004-12-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the Dept. of Nuclear and Reactor Physics reported here has been focused on different aspects of safety of the Accelerator-Driven Transmutation Systems and on Transmutation research in more general terms. An overview of the topics of our research is given in the Summary which is followed by detailed reports as separate chapters or subchapters. Some of the research topics reported in this report are referred to appendices, which have been published in the open literature. Topics, which are not yet published, are described with more details in the main part of this report. Main focus has been, as before, largely determined by the programme of the European projects of the 5th Framework Programme in which KTH is actively participating. In particular: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features. This activity includes even computer modeling of nuclear fuel production. Three different ADS-core concept are being investigated: Conceptual design of Pb-Bi cooled core with nitride fuel so called Sing-Sing Core developed at KTH; Pb-Bi cooled core with oxide fuel so called ANSALDO design for the European Project PDS-XADS; Gas cooled core with oxide fuel a design investigated for the European Project PDS-XADS. b) analysis of potential of advance fuels, in particular nitrides with high content of minor actinides; c) analysis of ADS-dynamics and assessment of major reactivity feedbacks; d) emergency heat removal from ADS; e) participation in ADS: MUSE (CEA-Cadarache), YALINA subcritical experiment in Minsk and designing of the subcritical experiment SAD in Dubna; f) theoretical and simulation studies of radiation damage in high neutron (and/or proton) fluxes; g) computer code and nuclear data development relevant for simulation and optimization of ADS, validation of the MCB code and sensitivity analysis; h) studies of

System and safety studies of accelerator driven transmutation. Annual Report 2003

Energy Technology Data Exchange (ETDEWEB)

Gudowski, Waclaw; Wallenius, Jan; Tucek, Kamil [Royal Inst. of Technology, Stockholm (Sweden). Dept. of Nuclear and Reactor Physics] [and others

2004-12-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the Dept. of Nuclear and Reactor Physics reported here has been focused on different aspects of safety of the Accelerator-Driven Transmutation Systems and on Transmutation research in more general terms. An overview of the topics of our research is given in the Summary which is followed by detailed reports as separate chapters or subchapters. Some of the research topics reported in this report are referred to appendices, which have been published in the open literature. Topics, which are not yet published, are described with more details in the main part of this report. Main focus has been, as before, largely determined by the programme of the European projects of the 5th Framework Programme in which KTH is actively participating. In particular: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features. This activity includes even computer modeling of nuclear fuel production. Three different ADS-core concept are being investigated: Conceptual design of Pb-Bi cooled core with nitride fuel so called Sing-Sing Core developed at KTH; Pb-Bi cooled core with oxide fuel so called ANSALDO design for the European Project PDS-XADS; Gas cooled core with oxide fuel a design investigated for the European Project PDS-XADS. b) analysis of potential of advance fuels, in particular nitrides with high content of minor actinides; c) analysis of ADS-dynamics and assessment of major reactivity feedbacks; d) emergency heat removal from ADS; e) participation in ADS: MUSE (CEA-Cadarache), YALINA subcritical experiment in Minsk and designing of the subcritical experiment SAD in Dubna; f) theoretical and simulation studies of radiation damage in high neutron (and/or proton) fluxes; g) computer code and nuclear data development relevant for simulation and optimization of ADS, validation of the MCB code and sensitivity analysis; h) studies of

Transmutation studies using SSNTD and radiochemistry and the associated production of secondary neutrons

CERN Document Server

Brandt, R; Wan, J S; Schmidt, T; Langrock, E J; Vater, P; Adam, J; Bamblevski, V P; Bradnova, V; Gelovani, L K; Kalinnikov, V K; Krivopustov, M I; Kulakov, B A; Sosnin, A N; Perelygin, V P; Pronskikh, V S; Stegailov, V I; Tsoupko-Sitnikov, V M; Modolo, G; Odoj, R; Philippen, P W; Adloff, J C; Pape, F; Debeauvais, M; Zamani-Valassiadou, M; Hashemi-Nezhad, S R; Dwivedi, K K; Guo Shi Lun; Li, L; Wang, Y L; Wilson, B

1999-01-01

Experiments using 1.5 GeV, 3.7 GeV and 7.4 GeV protons from the Synchrophasotron, LHE, JINR, Dubna, Russia, on extended Pb- and U- targets were carried out using SSNTD and radiochemical sensors for the study of secondary neutron $9 fluences. We also carried out first transmutation studies on the long-lived radwaste nuclei /sup 129/I and /sup 237/Np. In addition, we carried out computer code simulation studies on these systems using LAHET and DCM/CEM codes. We $9 have difficulties to understand rather large transmutation rates observed experimentally when they are compared with computer simulations. There seems to be a rather fundamental problem understanding the large transmutation rates as $9 observed experimentally in Dubna and CERN, as compared to those theoretical computer simulations mentioned above. (10 refs).

System and safety studies of accelerator driven systems for transmutation. Annual report 2007

Energy Technology Data Exchange (ETDEWEB)

Arzhanov, Vasily; Fokau, Andrei; Persson, Calle; Runevall, Odd; Sandberg, Nils; Tesinsky, Milan; Wallenius, Janne; Youpeng Zhang (Div. of Reactor Physics, Royal Institute of Technology, Stockholm (Sweden))

2008-05-15

Within the project 'System and safety studies of accelerator driven systems for transmutation', research on design and safety of sub-critical reactors for recycling of minor actinides is performed. During 2007, the reactor physics division at KTH has calculated safety parameters for EFIT-400 with cermet fuel, permitting to start the transient safety analysis. The accuracy of different reactivity meters applied to the YALINA facility was assessed and neutron detection studies were performed. A model to address deviations from point kinetic behaviour was developed. Studies of basic radiation damage physics included calculations of vacancy formation and activation enthalpies in bcc niobium. In order to predict the oxygen potential of inert matrix fuels, a thermo-chemical model for mixed actinide oxides was implemented in a phase equilibrium code

Study on MAs transmutation of accelerator-driven system sodium-cooled fast reactor loaded with metallic fuel

International Nuclear Information System (INIS)

Han Song; Yang Yongwei

2007-01-01

Through the analysis of the effect of heavy metal actinides on the effective multiplication constant (k eff ) of the core in accelerator-driven system (ADS) sodium-cooled fast reactor loaded with metallic fuel, we gave the method for determining fuel components. the characteristics of minor actinides (MAs) transmutation was analyzed in detail. 3D burn-up code COUPLE, which couples MCNP4c3 and ORIGEN2, was applied to the neutron simulation and burn up calculation. The results of optimized scheme shows that adjusting the proportion of 239 Pu and maintaining the value during the burn-up cycle is an efficient method of designing k eff and keeping stable during the burn-up cycle. Spallation neutrons lead to the neutron spectrum harder at inner core than that at outer core. It is in favor of improving MA's fission cross sections and the capture-to-fission ratio. The total MAs transmutation support ratio 8.3 achieves excellent transmutation effect. For higher flux at inner core leads to obvious differences on transmutation efficiency,only disposing MAs at inner core is in favor of decreasing the loading mass and improving MAs transmutation effect. (authors)

Minor Actinide Laboratory at JRC-ITU: Fuel fabrication facility

International Nuclear Information System (INIS)

Fernandez, A.; McGinley, J.; Somers, J.

2008-01-01

The Minor Actinide Laboratory (MA-lab) of the Institute for Transuranium Elements is a unique facility for the fabrication of fuels and targets containing minor actinides (MA). It is of key importance for research on Partitioning and Transmutation in Europe, as it is one of the only dedicated facilities for the fabrication of MA containing materials, either for property measurements or for the production of test pins for irradiation experiments. In this paper a detailed description of the MA-Lab facility and the fabrication processes developed to fabricate fuels and samples containing high content of minor actinides is given. In addition, experience gained and improvements are also outlined. (authors)

Conceptual design study of Hyb-WT as fusion–fission hybrid reactor for waste transmutation

International Nuclear Information System (INIS)

Siddique, Muhammad Tariq; Kim, Myung Hyun

2014-01-01

Highlights: • Conceptual design study of fusion-fission hybrid reactor for waste transmutation. • MCNPX and MONTEBURNS are compared for transmutation performance of WT-Hyb. • Detailed neutronic performance of final optimized Hyb-WT design is analyzed. • A new tube-in-duct core design is implemented and compared with pin type design. • Study shows many aspects of hybrid reactor even though scope was limited to neutronic analysis. - Abstract: This study proposes a conceptual design of a hybrid reactor for waste transmutation (Hyb-WT). The design of Hyb-WT is based on a low-power tokamak (less than 150 MWt) and an annular ring-shaped reactor core with metal fuel (TRU 60 w/o, Zr 40 w/o) and a fission product (FP) zone. The computational code systems MONTEBURNS and MCNPX2.6 are investigated for their suitability in evaluating the performance of Hyb-WT. The overall design performance of the proposed reactor is determined by considering pin-type and tube-in-duct core designs. The objective of such consideration is to explore the possibilities for enhanced transmutation with reduced wall loading from fusion neutrons and reduced transuranic (TRU) inventory. TRU and FP depletion is analyzed by calculating waste transmutation ratio, mass burned per full power year (in units of kg/fpy), and support ratio. The radio toxicity analysis of TRUs and FPs is performed by calculating the percentage of toxicity reduction in TRU and FP over a burn cycle

A Novel Molten Salt Reactor Concept to Implement the Multi-Step Time-Scheduled Transmutation Strategy

International Nuclear Information System (INIS)

Csom, Gyula; Feher, Sandor; Szieberthj, Mate

2002-01-01

Nowadays the molten salt reactor (MSR) concept seems to revive as one of the most promising systems for the realization of transmutation. In the molten salt reactors and subcritical systems the fuel and material to be transmuted circulate dissolved in some molten salt. The main advantage of this reactor type is the possibility of the continuous feed and reprocessing of the fuel. In the present paper a novel molten salt reactor concept is introduced and its transmutation capabilities are studied. The goal is the development of a transmutation technique along with a device implementing it, which yield higher transmutation efficiencies than that of the known procedures and thus results in radioactive waste whose load on the environment is reduced both in magnitude and time length. The procedure is the multi-step time-scheduled transmutation, in which transformation is done in several consecutive steps of different neutron flux and spectrum. In the new MSR concept, named 'multi-region' MSR (MRMSR), the primary circuit is made up of a few separate loops, in which salt-fuel mixtures of different compositions are circulated. The loop sections constituting the core region are only neutronically and thermally coupled. This new concept makes possible the utilization of the spatial dependence of spectrum as well as the advantageous features of liquid fuel such as the possibility of continuous chemical processing etc. In order to compare a 'conventional' MSR and a proposed MRMSR in terms of efficiency, preliminary calculational results are shown. Further calculations in order to find the optimal implementation of this new concept and to emphasize its other advantageous features are going on. (authors)

Neutron transmutation doping of silicon in the SAFARI-1 research reactor

International Nuclear Information System (INIS)

Louw, P.A.; Robertson, D.G.; Strydom, W.J.

1994-01-01

The SAFARI-1 research reactor has operated with an exemplary safety record since commissioning in 1965. As part of a commercialisation effort a silicon irradiation facility (SILIRAD) has been installed in the poolside region of SAFARI-1 for Neutron Transmutation Doping (NTD) of silicon. Commissioning of the facility took place in the last quarter of 1992 with a series of trial irradiations which were performed in close collaboration with Wacker Chemitronic of Germany. A methodology for the determination of irradiation times necessary to achieve the target resistivities was verified on the basis of the results from the trial irradiations. All production activities are controlled by quality assurance procedures. To date some hundred and twelve silicon ingots (103 mm diameter) have been successfully irradiated on a commercial contract basis. The observed axial and radial variations in the resistivity profile of the ingots are very small compared to the profiles associated with conventionally doped silicon and small tolerances on target resistivities are attained. In this paper an overview of the design and characterisation of SILIRAD is given and the methods applied that ensure a quality product are described. Results obtained from trial and production irradiations are presented and the envisaged future modifications to SILIRAD discussed

Neutron transmutation doping of silicon in the safari-1 research reactor

International Nuclear Information System (INIS)

Louw, P.A.; Robertson, D.G.; Strydom, W.J.

1994-01-01

The SAFARI-1 research reactor has operated with an exemplary safety record since commissioning in 1965. As part of a commercialisation effort a silicon irradiation facility (SILIRAD) has been installed in the poolside region of SAFARI-1 for Neutron Transmutation Doping (NTD) of silicon. Commissioning of the facility took place in the last quarter of 1992 with a series of trial irradiations which were performed in close collaboration the Wacker Chemitronic of Germany. A methodology for the determination of irradiation times necessary to achieve the target resistivities was verified on the basis of the results from the trial irradiations. All production activities are controlled by quality assurance procedures. To date some hundred and twelve silicon ingots (103 mm diameter) have been successfully irradiated on a commercial contract basis. The observed axial and radial variations in the resistivity profile of the ingots are very small compared to the profiles associated with conventionally doped silicon and small tolerances on target resistivities are attained. In this paper an overview of the design and characterisation of SILIRAD is given and the methods applied that ensure a quality product are described. Results obtained from trial and production irradiations are presented and the envisaged future modifications to SILIRAD discussed. 10 refs., 2 tabs., 6 figs

Transmutation of nuclear waste. Status report RAS programme 1993: Recycling and transmutation of actinides and fission products

International Nuclear Information System (INIS)

Abrahams, K.; Bultman, J.H.; Cordfunke, E.H.P.; Gruppelaar, H.; Janssen, A.J.; Franken, W.M.P.; Klippel, K.T.; Kloosterman, J.L.; Konings, R.J.M.; Smit, J.

1994-11-01

The term ''nuclear transmutation'' means a conversion of long-lived radioactive nuclides into short-lived or stable nuclides and ''recycling'' means re-use of fissile material to generate energy in power reactors. With these two processes a reduction of the radiotoxicity and of its duration may be achieved, thus reducing the potential hazard to future generations. Firstly, the report gives a survey of the present situation regarding nuclear waste: its components, how the waste is produced in current LWR and possible options for interim and final storage. Then the objective of the RAS programme, the working methods and the state of the art of the research are considered. Two chapters deal with preliminary results of national and international research. A rather tentative prediction for the future is formulated. Some conclusions are drawn: It seems to be in the best interests of the Netherlands to continue the established line of reprocessing nuclear waste, should new reactors be introduced. It may be advisable to make international agreements so that in the future fission products will contain as few traces of transuranic actinides and long-lived components as possible. Consequently, nuclear waste would become cleaner in terms of long-lived components. For the transmutation of products separated in foreign countries, the Netherlands could pursue an active policy, perform research and also consider the use of MOX fuel in future Dutch reactors. Further contributions towards the solution of these problems can only be made by the Netherlands on an international level. As such, the research and study performed within the framework of the RAS-programme represents a useful international contribution. The possibilities offered by the HFR are particularly of great value. Finally, the choice of a new generation of nuclear reactors should be made not based only on the safety aspects, but also on the extent of waste production and on the transmutation possibilities (application

Application of activation methods on the Dubna experimental transmutation set-ups.

Science.gov (United States)

Stoulos, S; Fragopoulou, M; Adloff, J C; Debeauvais, M; Brandt, R; Westmeier, W; Krivopustov, M; Sosnin, A; Papastefanou, C; Zamani, M; Manolopoulou, M

2003-02-01

High spallation neutron fluxes were produced by irradiating massive heavy targets with proton beams in the GeV range. The experiments were performed at the Dubna High Energy Laboratory using the nuclotron accelerator. Two different experimental set-ups were used to produce neutron spectra convenient for transmutation of radioactive waste by (n,x) reactions. By a theoretical analysis neutron spectra can be reproduced from activation measurements. Thermal-epithermal and fast-super-fast neutron fluxes were estimated using the 197Au, 238U (n,gamma) and (n,2n) reactions, respectively. Depleted uranium transmutation rates were also studied in both experiments.

Modern g,d,p,n-induced activation-transmutation systems

International Nuclear Information System (INIS)

Sublet, J.Ch.

2010-01-01

Document available in abstract form only. Full text of publication follows: The European Activation System (EASY) includes as the source of nuclear data the European Activation File (EAF) and as its engine the FISPACT activation-transmutation code. The latest version of the EAF, EAF-2010, contains cross-section data for gamma-, deuteron- and proton-induced reactions in addition to the traditional neutron-induced data. The main reason for the addition of these data to EAF is to enable activation-transmutation calculations to be performed for even more nuclear facilities, including 'accelerator'-driven devices with incident upper energy limit of 60 or 200 MeV. EAF-2010 has benefited from the generation and maintenance of comprehensive activation files in the past and the development of the processing code SAFEPAQ-II and model code TALYS. TALYS is the source for all gamma-, proton- and deuteron-induced data and a fair share of the neutron-induced data. Cross-section validation exercises against both experimental data and systematic, which were started in 1995, enable a comprehensive assessment of the data. Although EAF-2010 is certainly the most-validated activation neutron cross-section library in the world, currently less than 3% of all the reactions can be compared with experimental information, and even then only for a very limited, and not always application-relevant, energy range. As with EAF-2010, -2003, -2005 and -2007 results of integral experiments have been used to correct, adjust and validate data. This can be done using SAFEPAQ II by inputting the measured effective cross-sections. Validation using integral data has been performed by means of direct comparison with measurements of various materials under relevant particle spectra. A tool has recently been developed which is important now that the libraries contain so much TALYS-calculated data. Statistical analysis of cross-sections (SACS) is used to look for trends in the library data for a particular

The development of the market for neutron transmutation doped silicon

International Nuclear Information System (INIS)

Herzer, H.; Vieweg-Gutberlet, G.

1984-01-01

Neutron transmutation doped silicon was introduced to the electronic device market in the 1975-1976 time period. Today, neutron transmutation doping is definitely a mature technology applied mainly to semiconductor power devices. There is no doubt that the power device sector will remain the major consumer of NTD silicon in the near future. This paper examines the possible application of NTD silicon to other areas of the semiconductor market, and concludes that the need for NTD silicon will continue to grow and will expand into other applications. Consequently, unless new reactor capacities become available by the end of the decade, NTD silicon applications will probably be limited mainly to power and sensor devices

Neutronic evaluation of insertion of a transmutation layer in a Tokamak system

International Nuclear Information System (INIS)

Cabrera, Carlos Eduardo Velasquez

2013-01-01

Using MCNP5 code were simulated different models representing the ITER system. It was evaluated the two alloys used by the first wall under high neutron flux. The neutron flux and the reaction rate along the different walls were obtained and evaluated. Based on the results, it was possible to conclude the best way to represent the fusion device evaluating; the different geometrical models, the best material to be used in the first wall taking into consideration the objective of transmutation and placed the transmutation layer. (author)

Comparison of different options for minor actinide transmutation in the frame of the French law for waste management

International Nuclear Information System (INIS)

Chabert, Christine; Leudet, Alain; Saturnin, Anne

2011-01-01

In the frame of the French Act for waste management which has been passed by French Parliament on June 28th, 2006, it is requested to obtain in 2012 an assessment of industrial perspectives of partitioning and transmutation of long-lived elements. These studies must be carried out in tight connection with GENIV systems development. The expected results must include the evaluation of technical and economic scenarios taking into account the optimization options between the minor actinide transmutation processes, their interim storage and geological disposal, including an analysis of several criteria. In this perspective, the CEA has established a working group named 'GT TES' (Working Group on Technical and Economic Scenarios) involving EDF and AREVA to define scenarios, the various criteria to evaluate them, to conduct these evaluations and then to highlight the key results. The group also relied on ANDRA for the geological storage studies. The scenarios evaluations take place in the French context. The nuclear energy production is supposed to remain constant during the scenarios and equal to 430 TWhe/year in accordance with the current French nuclear power installed capacity of 60 GW(e). The deployment of the first Sodium-cooled Fast Reactor (SFR) starts in 2040, considering that at this date the SFR technology should be mature. Several management schemes of minor actinides have been studied: Plutonium recycling in SFR (minor actinides are sent to the waste). Plutonium recycling and minor actinide (or Am alone) transmutation in SFR and in homogeneous mode ('Hom.'). Plutonium recycling and minor actinide (or Am alone) transmutation in SFR and in heterogeneous mode ('Het.'). Plutonium recycling in SFR and minor actinide transmutation in Accelerator-Driven-System (ADS). The criteria used to analyze these different scenarios, should take into account the viewpoint of scientists, industrials, administrations, and the general public. They are listed below: Inventories and

Actinide and fission product partitioning and transmutation

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The third international information exchange meeting on actinide and fission product partitioning and transmutation, took place in Cadarache France, on 12-14 December 1994. The proceedings are presented in six sessions : an introduction session, the major programmes and international cooperation, the systems studies, the reactors fuels and targets, the chemistry and a last discussions session. (A.L.B.)

Composite gauge bosons of transmuted gauge symmetry

International Nuclear Information System (INIS)

Terazawa, Hidezumi.

1987-10-01

It is shown that effective gauge theories of composite gauge bosons describing the dynamics of composite quarks and leptons can be transmuted from the subcolor gauge theory describing that of subquarks due to the condensation of subquarks and that the equality of effective gauge coupling constants can result as in a grand unified gauge theory. (author)

Neutron-transmutation-doped germanium bolometers

International Nuclear Information System (INIS)

Palaio, N.P.; Rodder, M.; Haller, E.E.; Kreysa, E.

1983-02-01

Six slices of ultra-pure germanium were irradiated with thermal neutron fluences between 7.5 x 10 16 and 1.88 x 10 18 cm - 2 . After thermal annealing the resistivity was measured down to low temperatures ( 0 exp(δ/T) in the hopping conduction regime. Also, several junction FETs were tested for noise performance at room temperature and in an insulating housing in a 4.2K cryostat. These FETs will be used as first stage amplifiers for neutron-transmutation-doped germanium bolometers

Idaho National Engineering Laboratory irradiation facilities and their applications

International Nuclear Information System (INIS)

Gupta, V.P.; Herring, J.S.; Korenke, R.E.; Harker, Y.D.

1986-05-01

Although there is a growing need for neutron and gamma irradiation by governmental and industrial organizations in the United States and in other countries, the number of facilities providing such irradiations are limited. At the Idaho National Engineering Laboratory, there are several unique irradiation facilities producing high neutron and gamma radiation environments. These facilities could be readily used for nuclear research, materials testing, radiation hardening studies on electronic components/circuitry and sensors, and production of neutron transmutation doped (NTD) silicon and special radioisotopes. In addition, a neutron radiography unit, suitable for examining irradiated materials and assemblies, is also available. This report provides a description of the irradiation facilities and the neutron radiography unit as well as examples of their unique applications

Neutron data for accelerator-driven transmutation technologies. Annual Report 2002/2003

International Nuclear Information System (INIS)

Blomgren, J.; Hildebrand, A.; Mermod, P.; Olsson, N.; Pomp, S.; Oesterlund, M.

2003-08-01

The project NATT, Neutron data for Accelerator-driven Transmutation Technology, is performed within the nuclear reactions group of the Department for neutron research, Uppsala university. The activities of the group is directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group has previously developed two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: Analysis and documentation has been finalized of previously performed measurements of elastic neutron scattering from carbon and lead at 96 MeV. The precision in the results surpasses all previous data by at least an order of magnitude. These measurements represent the highest energy in neutron scattering where the ground state has been resolved. The results show that all previous theory work has underestimated the probability for neutron scattering at the present energy by 0-30 %. A new method for measurements of absolute probabilities for neutron-induced nuclear reactions with experimental techniques only has been developed. Previously, only two such methods have been known. One student has reached his PhD exam. Two PhD students have been accepted. TSL has decided to build a new neutron beam facility with significantly improved performance for these, and similar, activities. A new instrument for measurements of inelastic neutron scattering has been built, tested and found to meet the specifications. This work has been performed in collaboration with two French research groups from Caen and Nantes. The instrument is intended to be used for a series of experiments during the coming years. Previous work by the group on nuclear data for assessment of electronics reliability has lead to a new industry standard in the USA

Neutron data for accelerator-driven transmutation technologies. Annual Report 2002/2003

Energy Technology Data Exchange (ETDEWEB)

Blomgren, J.; Hildebrand, A.; Mermod, P.; Olsson, N.; Pomp, S.; Oesterlund, M. [Uppsala Univ. (Sweden). Dept. for Neutron Research

2003-08-01

The project NATT, Neutron data for Accelerator-driven Transmutation Technology, is performed within the nuclear reactions group of the Department for neutron research, Uppsala university. The activities of the group is directed towards experimental studies of nuclear reaction probabilities of importance for various applications, like transmutation of nuclear waste, biomedical effects and electronics reliability. The experimental work is primarily undertaken at the The Svedberg Laboratory (TSL) in Uppsala, where the group has previously developed two world-unique instruments, MEDLEY and SCANDAL. Highlights from the past year: Analysis and documentation has been finalized of previously performed measurements of elastic neutron scattering from carbon and lead at 96 MeV. The precision in the results surpasses all previous data by at least an order of magnitude. These measurements represent the highest energy in neutron scattering where the ground state has been resolved. The results show that all previous theory work has underestimated the probability for neutron scattering at the present energy by 0-30 %. A new method for measurements of absolute probabilities for neutron-induced nuclear reactions with experimental techniques only has been developed. Previously, only two such methods have been known. One student has reached his PhD exam. Two PhD students have been accepted. TSL has decided to build a new neutron beam facility with significantly improved performance for these, and similar, activities. A new instrument for measurements of inelastic neutron scattering has been built, tested and found to meet the specifications. This work has been performed in collaboration with two French research groups from Caen and Nantes. The instrument is intended to be used for a series of experiments during the coming years. Previous work by the group on nuclear data for assessment of electronics reliability has lead to a new industry standard in the USA.

Evaluation of actinide partitioning and transmutation

International Nuclear Information System (INIS)

1982-01-01

After a few centuries of radioactive decay the long-lived actinides, the elements of atomic numbers 89-103, may constitute the main potential radiological health hazard in nuclear wastes. This is because all but a very few fission products (principally technetium-99 and iodine-129) have by then undergone radioactive decay to insignificant levels, leaving the actinides as the principal radionuclides remaining. It was therefore at first sight an attractive concept to recycle the actinides to nuclear reactors, so as to eliminate them by nuclear fission. Thus, investigations of the feasibility and potential benefits and hazards of the concept of 'actinide partitioning and transmutation' were started in numerous countries in the mid-1970s. This final report summarizes the results and conclusions of technical studies performed in connection with a four-year IAEA Co-ordinated Research Programme, started in 1976, on the ''Environmental Evaluation and Hazard Assessment of the Separation of Actinides from Nuclear Wastes followed by either Transmutation or Separate Disposal''. Although many related studies are still continuing, e.g. on waste disposal, long-term safety assessments, and waste actinide management (particularly for low and intermediate-level wastes), some firm conclusions on the overall concept were drawn by the programme participants, which are reflected in this report

A review of research and development on accelerator-driven system for transmutation of long-lived nuclear waste at JAERI

International Nuclear Information System (INIS)

Oigawa, H.

2004-01-01

The dedicated transmutation system using the accelerator driven subcritical system (ADS) has been studied in the Japan Atomic Energy Research Institute (JAERI) to reduce the burden of the final disposal of the nuclear waste. A subcritical reactor with the thermal power of 800 MW is proposed, where 250 kg of minor actinide (MA) can be transmuted annually. A superconducting linear accelerator (LINAC) with the beam power of 20-30 MW is necessary for this ADS. Lead-bismuth eutectic (LBE) is used for both the spallation target and the core coolant. Many research and development activities including the design study are under way and planned at JAERI to examine the feasibility of the ADS. In the design study, optimization of the ADS design is under way in terms of neutronics and structural feasibility. In the field of the proton accelerator, a superconducting LINAC is being developed. In the field of the LBE technology, material compatibility, thermal-hydraulics and polonium behavior are being studied. The irradiation effect of structural material to be used for the beam window is also being studied. In the field of the reactor physics of the subcritical core fueled with MA, the reliability of nuclear data is examined and the subcriticality monitoring technique is being investigated. Moreover, in the framework of J-PARC project (Japan Proton Accelerator Research Complex), JAERI plans to construct the Transmutation Experimental Facility (TEF) to demonstrate the feasibility of the ADS with using high-energy proton beam, to accumulate valuable knowledge about reactor physics and operation of ADS, and to establish a database for LBE spallation target and relevant materials. (author)

Minor actinide transmutation in a board type sodium cooled breed and burn reactor core

International Nuclear Information System (INIS)

Zheng, Meiyin; Tian, Wenxi; Zhang, Dalin; Qiu, Suizheng; Su, Guanghui

2015-01-01

Highlights: • A 1250 MWt board type sodium cooled breed and burn reactor core is further designed. • MCNP–ORIGEN coupled code MCORE is applied to perform neutronics and depletion calculation. • Transmutation efficiency and neutronic safety parameters are compared under different MA weight fraction. - Abstract: In this paper, a board type sodium cooled breed and burn reactor core is further designed and applied to perform minor actinide (MA) transmutation. MA is homogeneously loaded in all the fuel sub-assemblies with a weight fraction of 2.0 wt.%, 4.0 wt.%, 6.0 wt.%, 8.0 wt.%, 10.0 wt.% and 12.0 wt.%, respectively. The transmutation efficiency, transmutation amount, power density distribution, neutron fluence distribution and neutronic safety parameters, such as reactivity, Doppler feedback, void worth and delayed neutron fraction, are compared under different MA weight fraction. Neutronics and depletion calculations are performed based on the self-developed MCNP–ORIGEN coupled code with the ENDF/B-VII data library. In the breed and burn reactor core, a number of breeding sub-assemblies are arranged in the inner core in a board type way (scatter load) to breed, and a number of absorbing sub-assemblies are arranged in the inner side of the outer core to absorb neutrons and reduce power density in this area. All the fuel sub-assemblies (ignition and breeding sub-assemblies) are shuffled from outside in. The core reached asymptotically steady state after about 22 years, and the average and maximum discharged burn-up were about 17.0% and 35.3%, respectively. The transmutation amount increased linearly with the MA weight fraction, while the transmutation rate parabolically varied with the MA weight fraction. Power density in ignition sub-assembly positions increased with the MA weight fraction, while decreased in breeding sub-assembly positions. Neutron fluence decreased with the increase of MA weight fraction. Generally speaking, the core reactivity and void

Study on the transmutation of some radioactive wastes using the Bateman equations

International Nuclear Information System (INIS)

Orlandi, Horus Ibrahim; Moreira, Joao M.L.

2009-01-01

In this work, a numerical solution for the nuclear transmutation equations using the Bateman algorithm. The numerical solution was implemented using the JAVA language and the program gives the time variation of isotope chain decays population which appears due to nuclear transmutation. With the present results it is possible to understand the radioactive decay and the need of storage the radioactive decay along the years. The chain decay studied were the 99 Tc, 99 Zr, 135 Cs, 137 Cs and the 90 Sr, due to their long half-lives and the high fission yield

Concept of the demonstration molten salt unit for the transuranium elements transmutations

International Nuclear Information System (INIS)

Alekseev, P.; Dudnikov, A.; Prusakov, V.; Subbotin, S.; Zakirov, R.; Lelek, V.; Peka, I.

1999-01-01

Fluorine reprocessing is discussed of spent fuel and of fluoride molten salt reactor in critical and subcritical modes for plutonium and minor actinides burning. International collaboration for creation of such system is proposed. Additional neutron source in the core will have positive influence on the transmutation processes in the reactor. Demonstration critical molten salt reactor of small power capacity will permit to decide the most part of problems inherent to large critical reactors and subcritical drivers. It could be expected that fluoride molten salt transmuter can work without accelerator as a critical reactor. (author)

Importance of All-in-one (MCNPX2.7.0+CINDER2008) Code for Rigorous Transmutation Study

Energy Technology Data Exchange (ETDEWEB)

Kim, Oyeon [Institute for Modeling and Simulation Convergence, Daegu (Korea, Republic of); Kim, Kwanghyun [RadTek Co. Ltd., Daejeon (Korea, Republic of)

2015-10-15

It can be utilized as a possible mechanism for reducing the volume and hazard of radioactive waste by transforming hazardous radioactive elements with long half-life into less hazardous elements with short halflife. Thus, the understanding of the transmutation mechanism and beneficial machinery design technologies are important and useful. Although the terminology transmutation was rooted back to alchemy which transforms the base metals into gold in the middle ages, Rutherford and Soddy were the first observers by discovering the natural transmutation as a part of radioactive decay of the alpha decay type in early 20th century. Along with the development of computing technology, analysis software, for example, CINDER was developed for rigorous atomic transmutation study. The code has a long history of development from the original work of T. England at Bettis Atomic Power Laboratory (BAPL) in the early 1960s. It has been used to calculate the inventory of nuclides in an irradiated material. CINDER'90 which is recently released involved an upgrade of the code to allow the spontaneous tracking of chains based upon the significant density or pass-by of a nuclide, where pass-by represents the density of a nuclide transforming to other nuclides. Nuclear transmutation process is governed by highly non-linear differential equation. Chaotic nature of the non-linear equation bespeaks the importance of the accurate input data (i.e. number of significant digits). Thus, reducing the human interrogation is very important for the rigorous transmutation study and 'allin- one' code structure is desired. Note that non-linear characteristic of the transmutation equation caused by the flux changes due to the number density change during a given time interval (intrinsic physical phenomena) is not considered in this study. In this study, we only emphasized the effects of human interrogation in the computing process solving nonlinear differential equations, as shown in

Transmutation of radioactive nuclear waste – present status and ...

Indian Academy of Sciences (India)

Transmutation of long-lived actinides and fission products becomes an im- ... Similar approach was performed for sub critical fast reactor core with Pu/MA .... The same might be addressed to masses of nuclei (the use of experimental values.

System and safety studies of accelerator driven transmutation systems

Energy Technology Data Exchange (ETDEWEB)

Gudowski, W.; Wallenius, J.; Tucek, K.; Eriksson, Marcus; Carlsson, Johan; Seltborg, P.; Cetnar, J. [Royal Inst. of Technology, Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

2001-05-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the department has been focused on: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features; b) analysis of ADS-dynamics c) computer code and nuclear data development relevant for simulation and optimization of ADS; d) participation in ADS experiments including 1 MW spallation target manufacturing, subcritical experiments MUSE (CEA-Cadarache). Moreover, during the reporting period the EU-project 'IABAT', co-ordinated by the department has been finished and 4 other projects have been initiated in the frame of the 5th European Framework Programme. Most of the research topics reported in this paper are referred to appendices, which have been published in the open literature. The topics, which are not yet published, are described here in more details.

System and safety studies of accelerator driven transmutation systems

International Nuclear Information System (INIS)

Gudowski, W.; Wallenius, J.; Tucek, K.; Eriksson, Marcus; Carlsson, Johan; Seltborg, P.; Cetnar, J.

2001-05-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the department has been focused on: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features; b) analysis of ADS-dynamics c) computer code and nuclear data development relevant for simulation and optimization of ADS; d) participation in ADS experiments including 1 MW spallation target manufacturing, subcritical experiments MUSE (CEA-Cadarache). Moreover, during the reporting period the EU-project 'IABAT', co-ordinated by the department has been finished and 4 other projects have been initiated in the frame of the 5th European Framework Programme. Most of the research topics reported in this paper are referred to appendices, which have been published in the open literature. The topics, which are not yet published, are described here in more details

Definition of Technology Readiness Levels for Transmutation Fuel Development

International Nuclear Information System (INIS)

Jon Carmack; Kemal O. Pasamehmetoglu

2008-01-01

To quantitatively assess the maturity of a given technology, the Technology Readiness Level (TRL) process is used. The TRL process has been developed and successfully used by the Department of Defense (DOD) for development and deployment of new technology and systems for defense applications. In addition, NASA has also successfully used the TRL process to develop and deploy new systems for space applications. Transmutation fuel development is a critical technology needed for closing the nuclear fuel cycle. Because the deployment of a new nuclear fuel forms requires a lengthy and expensive research, development, and demonstration program, applying the TRL concept to the transmutation fuel development program is very useful as a management and tracking tool. This report provides definition of the technology readiness level assessment process as defined for use in assessing nuclear fuel technology development for the Transuranic Fuel Development Campaign

Fusion-Fission Transmutation Scheme-Efficient destruction of nuclear waste

International Nuclear Information System (INIS)

Kotschenreuther, M.; Valanju, P.M.; Mahajan, S.M.; Schneider, E.A.

2009-01-01

A fusion-assisted transmutation system for the destruction of transuranic nuclear waste is developed by combining a subcritical fusion-fission hybrid assembly uniquely equipped to burn the worst thermal nonfissile transuranic isotopes with a new fuel cycle that uses cheaper light water reactors for most of the transmutation. The center piece of this fuel cycle, the high power density compact fusion neutron source (100 MW, outer radius <3 m), is made possible by a new divertor with a heat-handling capacity five times that of the standard alternative. The number of hybrids needed to destroy a given amount of waste is an order of magnitude below the corresponding number of critical fast-spectrum reactors (FRs) as the latter cannot fully exploit the new fuel cycle. Also, the time needed for 99% transuranic waste destruction reduces from centuries (with FR) to decades

Fuels and materials for transmutation. A status report

International Nuclear Information System (INIS)

2005-01-01

The safe and efficient management of spent fuel from the operation of commercial nuclear power plants is an important issue. Worldwide, more than 250 000 tons of spent fuel from reactors currently operating will require disposal. These numbers account for only high-level radioactive waste generated by present-day power reactors. Nearly all issues related to risks to future generations arising from the long-term disposal of such spent nuclear fuel is attributable to only about 1% of its content. This 1% is made up primarily of plutonium, neptunium, americium and curium (called transuranic elements) and the long-lived isotopes of iodine and technetium. When transuranics are removed from discharged fuel destined for disposal, the toxic nature of the spent fuel drops below that of natural uranium ore (that which was originally mined for the nuclear fuel) within a period of several hundred to a thousand years. This significantly reduces the burden on geological repositories and the problem of addressing the remaining long-term residues can thus be done in controlled environments having timescales of centuries rather than millennia stretching beyond 10 000 years. Transmutation is one of the means being explored to address the disposal of transuranic elements. To achieve this, advanced reactor systems, appropriate fuels, separation techniques and associated fuel cycle strategies are required. This report describes the current status of fuel and material technologies for transmutation and suggests technical R and D issues that need to be resolved. It will be of particular interest to nuclear fuel and material scientists involved in the field of partitioning and transmutation (P and T), and in advanced fuel cycles in general. (author)

HYPERFUSE: a novel inertial confinement system utilizing hypervelocity projectiles for fusion energy production and fission waste transmutation

International Nuclear Information System (INIS)

Makowitz, H.; Powell, J.R.; Wiswall, R.

1980-01-01

Parametric system studies of an inertial confinement fusion (ICF) reactor system to transmute fission products from an LWR economy have been carried out. The ICF reactors would produce net power in addition to transmuting fission products. The particular ICF concept examined is an impact fusion approach termed HYPERFUSE, in which hypervelocity pellets, traveling on the order of 100 to 300 km/sec, collide with each other or a target block in a reactor chamber and initiate a thermonuclear reaction. The DT fusion fuel is contained in a shell of the material to be transmuted, e.g., 137 Cs or 90 Sr. The 14-MeV fusion neutrons released during the pellet burn cause transmutation reactions (e.g., (n, 2n), (n, α), etc.) that convert the long lived fission products (FP's) either to stable products or to species that decay with a short half-life to a stable product

Establishment of bases for joint study and cooperation on long-lived radionuclides transmutation between Korea and Russia

International Nuclear Information System (INIS)

Yoo, Jae Hyung; Lee, Byung Jik; Shim, Joon Bo; Choi, Chang Joo; Park, Won Seok; Song, Tae Young; Kim, Chang Kyu; Kil, Choong Sup

2003-02-01

The most important technical fields related to transmutation are partitioning of long-lived radionuclides and transmutation system to be used for converting them into short-lived or stable radionuclides. Technical cooperation between Korea and Russia is needed because Russia has an unequalled position in the fields of development of the fast reactors and pyrochemical processes around the world. The aim of this project is an establishment of bases for coordination on transmutation technology between Korea and Russia. State of the art of domestic and foreign countries upon partitioning of long-lived radionuclides, transmutation system and Gen IV development was summarized. Also, the 7th Korea-Russia joint coordination committee meeting and the 1st joint workshop were held as a result of this project. Technical fields and scheme on future cooperation between Korea and Russia were discussed and agreed in the course of the meetings

Determination of procedures for transmutation of fission product wastes by fusion neutrons. Volume 2. Final report

International Nuclear Information System (INIS)

Lang, G.P.

1980-12-01

This study is concerned with the engineering aspects of the transmutation of fission products utilizing neutrons generated in fusion reactors. It is assumed that fusion reactors, although not yet developed, will be available around the turn of the century. Therefore, early studies of this type are appropriate as a guide to the large amount of further investigations that will be needed to fully evaluate this concept. Not all of the radioactive products from light water reactors can be economically transmuted, but it appears that the most hazardous can. This requires that fission-product wastes must first be separated into a number of fractions, and in some instances this must be accomplished with extremely high separation factors. A review of current commercial separation processes and of promising methods that are now in the laboratory stage indicate that the necessary processes can most likely be developed but will require an active and sustained development program. Current fusion reactor concepts were examined as to their suitability for transmuting the separated fission wastes. It was concluded that the long-lived fission products were most amenable to transmutation. The medium-lived fission products, Cs-137 and Sr-90, require higher neutron fluxes than are available in the most developed fusion reactor concepts. Concepts which are less developed may eventually be adaptable as transmuters of these fission products

Effects of actinide compositional variability in the U.S. spent fuel inventory on partitioning-transmutation systems

International Nuclear Information System (INIS)

Ludwig, S.B.; Michaels, G.E.; Hanson, B.D.

1993-01-01

The partitioning and transmutation concept (P-T) has as a mission the reduction by many orders of magnitude of certain undesirable nuclides in the waste streams. Given that only a very small fiction of spent fuel can be rejected by a P-T enterprise, a P-T system must therefore be capable of accommodating a wide range of spent fuel characteristics. Variability of nuclide composition (i.e. the feed material for transmutation devices) may be important because virtually all transmutation systems propose to configure TRU nuclides recovered from discharged LWR fuel in critical or near-critical cores. To date, all transmutation system core analyses assume nonvariable nuclide concentrations for startup and recycle cores. Using the Department of Energy (DOES) Characteristic Data Base (CDB) and the ORIGEN2 computer code, the current and projected spent fuel discharges until the year 2016 have been categorized according to combinations of fuel burnup, initial enrichment, fuel age (cooling time) and reactor type (boiling-water or pressurized-water reactor). In addition to quantifying the variability of nuclide composition in current and projected LWR fuel discharge, the variability of the infinite multiplication factor (K ∞ ) is calculated for both fast (ALMR) and thermal (accelerator-based) transmuter systems. It is shown that actinide compositional variations are potentially significant and warrant further investigation. (authors)

Neutron-transmuted carbon-14 in neutron-irradiated GaN: Compensation of DX-like center

International Nuclear Information System (INIS)

Ida, T.; Oga, T.; Kuriyama, K.; Kushida, K.; Xu, Q.; Fukutani, S.

2013-01-01

The transmuted-C related luminescence and net carrier concentration are studied by combining photoluminescence, liquid scintillation, and Raman scattering. GaN single crystal films grown by metalorganic-vapor-phase epitaxy are irradiated with fast and thermal neutrons at fluxes of 3.9 × 10 13 cm −2 s −1 and 8.15 × 10 13 cm −2 s −1 , respectively. Irradiation time is 48 hours. The calculated 72 Ge and 14 C concentrations are 1.24 × 10 18 cm −3 and 1.13 × 10 18 cm −3 , respectively. The transmuted 14 C is detected by the liquid scintillation method to survey β-rays emitted in the process of 14 C decays from 14 N. Tritium ( 3 H) is also emitted by a (n,t) reaction of 14 N due to the neutron irradiation above 4.5 MeV. Photoluminescence relating to C, DX-like center of Ge and yellow luminescence band are observed in 1000 °C annealed NTD-GaN. The free electron concentration estimated from Raman scattering is 4.97 × 10 17 cm −3 . This value is lower than that from the transmuted Ge concentration, suggesting the compensation due to the transmuted 14 C acceptors

Study on partitioning and transmutation (P and T) of high-level waste. Status of R and D. Final report

International Nuclear Information System (INIS)

Merk, Bruno; Glivici-Cotruta, Varvara

2014-01-01

The main project, where this sub project contributed to, has been structured into two modules: module A (funded by the federal ministry of economics, managed by KIT) and module B (funded by the federal ministry of education and research, managed by acatech). Partners in module A were DBE TECHNOLOGY GmbH, the Gesellschaft fuer Anlagen- und Reaktorsicherheit mbH (GRS), the Helmholtz-Zentrum Dresden-Rossendorf (HZDR), the Karlsruher Institute of Technology (KIT) and the Rheinisch-Westfaelische Technische Hochschule (RWTH) Aachen, in co-operation with the Forschungszentrum Juelich (FZJ). Modul B has been executed by the Zentrum fuer Interdisziplinaere Risiko- und Innovationsforschung der Universitaet Stuttgart (ZIRIUS). The overall coordination has been carried out by the Deutsche Akademie der Technikwissenschaften (acatech). The social implications have been evaluated in module B based on the analysis of the scientific and technological aspects in module A. Recommendations for communication and actions to be taken for the future positioning of P and T have been developed. In the project part, coordinated by HZDR - status of R and D - an overview on the whole topic P and T is given. The topic is opened by a short description of reactor systems possible for transmutation. In the following the R and D status of separation technologies, safety technology, accelerator technology, liquid metal technology, spallation target development, transmutation fuel and structural material development, as well as waste conditioning is described. The topic is completed by the specifics of transmutation systems, the basic physics and core designs, the reactor physics, the simulation tools and the development of Safety Approaches. Additionally, the status of existing irradiation facilities with fast neutron spectrum is described. Based on the current R and D status, the research and technology gaps in the topics: separation and conditioning, accelerator and spallation target, and reactor

Method for the transmutation of nuclides

International Nuclear Information System (INIS)

1984-01-01

The invention relates to a method for the systematic and optimal manufacture of nuclides with beneficial properties as well as for the transmutation of noxious nuclides into innocuous ones, e.g. radioactive wastes. For that purpose, use is made of the periodic system of atoms and of the so-called twin-subshell model of nuclear structure, in order to trace the possible transformations of the nuclide through irradiation with appropriate particles or radiation. (G.J.P.)

Transmutation of Thermocouples in Thermal and Fast Nuclear Reactors

International Nuclear Information System (INIS)

Scervini, M.; Rae, C.; Lindley, B.

2013-06-01

Thermocouples are the most commonly used sensors for temperature measurement in nuclear reactors. Their role is fundamental for the control of current nuclear reactors and for the development of the nuclear technology needed for the implementation of GEN IV nuclear reactors. When used for in-core measurements thermocouples are strongly affected not only by high temperatures, but also by intense neutron fluxes. As a result of the interaction with neutrons, the thermoelements of the thermocouples undergo transmutation, which produces a time dependent change in composition in the thermoelements and, as a consequence, a time dependent drift in the thermocouple signal. Thermocouple drift can be very significant for in-pile temperature measurements and may render the temperature sensors unreliable after exposure to nuclear radiation for relatively short times compared to the life required for temperature sensors in nuclear applications. In this work, undertaken as part of the European project METROFISSION, the change in composition occurring in irradiated thermocouples has been calculated using the software ORIGEN 2.2. Several thermocouples have been considered, including Nickel based thermocouples (type K and type N), Tungsten based thermocouples (W-5%Re vs W-26%Re and W- 3%Re vs W-25%Re), Platinum based thermocouples (type S and Platinum vs Palladium) and Molybdenum vs Niobium thermocouples. The transmutation induced by both thermal flux and fast flux has been calculated. Thermocouples undergo more pronounced transmutation in thermal fluxes rather than in fast fluxes, as the neutron cross section of an element is higher for thermal energies. Nickel based thermocouples have a minimal change in composition, while Platinum based and Tungsten based thermocouples experience a very significant transmutation. The use of coatings deposited on the sheath of a thermocouple has been considered as a mean to reduce the neutron flux the thermoelements inside the thermocouple sheath

Monte Carlo analysis of the long-lived fission product neutron capture rates at the Transmutation by Adiabatic Resonance Crossing (TARC) experiment

International Nuclear Information System (INIS)

Abánades, A.; Álvarez-Velarde, F.; González-Romero, E.M.; Ismailov, K.; Lafuente, A.; Nishihara, K.; Saito, M.; Stanculescu, A.; Sugawara, T.

2013-01-01

Highlights: ► TARC experiment benchmark capture rates results. ► Utilization of updated databases, included ADSLib. ► Self-shielding effect in reactor design for transmutation. ► Effect of Lead nuclear data. - Abstract: The design of Accelerator Driven Systems (ADS) requires the development of simulation tools that are able to describe in a realistic way their nuclear performance and transmutation rate capability. In this publication, we present an evaluation of state of the art Monte Carlo design tools to assess their performance concerning transmutation of long-lived fission products. This work, performed under the umbrella of the International Atomic Energy Agency, analyses two important aspects for transmutation systems: moderation on Lead and neutron captures of 99 Tc, 127 I and 129 I. The analysis of the results shows how shielding effects due to the resonances at epithermal energies of these nuclides affects strongly their transmutation rate. The results suggest that some research effort should be undertaken to improve the quality of Iodine nuclear data at epithermal and fast neutron energy to obtain a reliable transmutation estimation.

Prognosis and comparison of performances of composite CERCER and CERMET fuels dedicated to transmutation of TRU in an EFIT ADS

Science.gov (United States)

Sobolev, V.; Uyttenhove, W.; Thetford, R.; Maschek, W.

2011-07-01

The neutronic and thermomechanical performances of two composite fuel systems: CERCER with (Pu,Np,Am,Cm)O 2-x fuel particles in ceramic MgO matrix and CERMET with metallic Mo matrix, selected for transmutation of minor actinides in the European Facility for Industrial Transmutation (EFIT), were analysed aiming at their optimisation. The ALEPH burnup code system, based on MNCPX and ORIGEN codes and JEFF3.1 nuclear data library, and the modern version of the fuel rod performance code TRAFIC were used for this analysis. Because experimental data on the properties of the mixed minor-actinide oxides are scarce, and the in-reactor behaviour of the T91 steel chosen as cladding, as well as of the corrosion protective layer, is still not well-known, a set of "best estimates" provided the properties used in the code. The obtained results indicate that both fuel candidates, CERCER and CERMET, can satisfy the fuel design and safety criteria of EFIT. The residence time for both types of fuel elements can reach about 5 years with the reactivity swing within ±1000 pcm, and about 22% of the loaded MA is transmuted during this period. However, the fuel centreline temperature in the hottest CERCER fuel rod is close to the temperature above which MgO matrix becomes chemically instable. Moreover, a weak PCMI can appear in about 3 years of operation. The CERMET fuel can provide larger safety margins: the fuel temperature is more than 1000 K below the permitted level of 2380 K and the pellet-cladding gap remains open until the end of operation.

Proposal of experimental facilities for studies of nuclear data and radiation engineering in the Intense Proton Accelerator Project

CERN Document Server

Baba, M; Nagai, Y; Ishibashi, K

2003-01-01

A proposal is given on the facilities and experiments in the Intense Proton Accelerator Project (J-PARC) relevant to the nuclear data and radiation engineering, nuclear astrophysics, nuclear transmutation, accelerator technology and space technology and so on. (3 refs).

Multivariate data analysis of process control data from neutron transmutation doping of silicon

DEFF Research Database (Denmark)

Heydorn, K.; Hegaard, N.

1994-01-01

Final resistivities obtained by neutron transmutation doping (NTD) of silicon can be measured only after an annealing process has been carried out at the manufacturer's plant. The reactor centre carrying out the neutron doping process by irradiation under selected conditions must control the proc......Final resistivities obtained by neutron transmutation doping (NTD) of silicon can be measured only after an annealing process has been carried out at the manufacturer's plant. The reactor centre carrying out the neutron doping process by irradiation under selected conditions must control...

Flexibility of ADS for minor actinides transmutation in different two-stage PWR-ADS fuel cycle scenarios

International Nuclear Information System (INIS)

Zhou, Shengcheng; Wu, Hongchun; Zheng, Youqi

2018-01-01

Highlights: •ADS reloading scheme is optimized to raise discharge burnup and lower reactivity loss. •ADS is flexible to be combined with various pyro-chemical reprocessing technologies. •ADS is flexible to transmute MAs from different spent PWR fuels. -- Abstract: A two-stage Pressurized Water Reactor (PWR)-Accelerator Driven System (ADS) fuel cycle is proposed as an option to transmute minor actinides (MAs) recovered from the spent PWR fuels in the ADS system. At the second stage, the spent fuels discharged from ADS are reprocessed by the pyro-chemical process and the recovered actinides are mixed with the top-up MAs recovered from the spent PWR fuels to fabricate the new fuels used in ADS. In order to lower the amount of nuclear wastes sent to the geological repository, an optimized scattered reloading scheme for ADS is proposed to maximize the discharge burnup and lower the burnup reactivity loss. Then the flexibility of ADS for MA transmutation is evaluated in this research. Three aspects are discussed, including: different cooling time of spent ADS fuels before reprocessing, different reprocessing loss of spent ADS fuels, and different top-up MAs recovered from different kinds of spent PWR fuels. The ADS system is flexible to be combined with various pyro-chemical reprocessing technologies with specific spent fuels cooling time and unique reprocessing loss. The reduction magnitudes of the long-term decay heat and radiotoxicity of MAs by transmutation depend on the reprocessing loss. The ADS system is flexible to transmute MAs recovered from different kinds of spent PWR fuels, regardless of UOX or MOX fuels. The reduction magnitudes of the long-term decay heat and radiotoxicity of different MAs by transmutation stay on the same order.

Partitioning and Transmutation. Annual Report 2004

Energy Technology Data Exchange (ETDEWEB)

Andersson, Sofie; Drouet, Francois; Ekberg, Christian; Liljenzin, Jan-Olov; Magnusson, Daniel; Nilsson, Mikael; Retegan, Teodora; Skarnemark, Gunnar [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Materials and Surface Chemistry

2005-01-01

The long-lived elements in the spent nuclear fuels are mostly actinides, some fission products ({sup 129}I, {sup 99}Tc, {sup 135}Cs, {sup 93}Zr and {sup 126}Sn and activation products ({sup 14}C and {sup 36}Cl). To be able to destroy the long-lived elements in a transmutation process they must be separated from the rest of the spent nuclear fuel. The most difficult separations to make are those between trivalent actinides and lanthanides, due to their relatively similar chemical properties, and those between different actinides themselves. This separation is necessary to obtain the desired efficiency in the transmutation process in order not to create any unnecessary waste thus rendering the process useless. Solvent extraction is an efficient and well-known method that makes it possible to have separation factors that fulfil the highly set demands on purity of the separated phases and on small losses. Chalmers University of Technology is involved in research regarding the separation of actinides and lanthanides and between the actinides themselves as a partner in the European Union sixth framework program project EUROPART. This is a continuation of the projects we participated in within the fourth and fifth framework programmes NEWPART and PARTNEW respectively. The aims of the projects have now shifted from basic understanding to more applied research with focus on process development.

Separation of technetium from ruthenium after the accelerator transmutation of technetium

International Nuclear Information System (INIS)

Abney, K.D.; Schroeder, N.C.; Kinkead, S.A.; Attrep, M. Jr.

1992-01-01

Both civilian and defense related waste must be processed with a strategy for dealing with Tc. One solution is to remove the Tc from the waste steam and transmute the Tc to stable Ru in either a reactor or an accelerator. Before any processing of waste streams can be performed (even if transmutation is not performed) the separations chemistry from the spent fuels or the stored wastes containing Tc must be developed. This report details some of the separation schemes possible for the separation of Tc and Ru, which include the baseline ion exchange process of Roberts, Smith and Wheelwright, ozonolysis, filtration, magnetic separation, solvent extraction, electrodeposition, fluorination, and pyrolysis. 5 figs, 4 refs

Annealing behaviour of excess carriers in neutron-transmutation-doped silicon

International Nuclear Information System (INIS)

Maekawa, T.; Nogami, S.; Inoue, S.

1993-01-01

In neutron-transmutation-doped silicon wafers excess carriers are clearly generated over the transmuted phosphorus atoms. The generation occurs for annealing temperatures above 900 o C. The maximum percentage of excess carriers obtained is about 24.5% of the final carrier concentration. Due to the difference in energy of generation and removal, the excess carriers can be removed by annealing above 800 o C. The radiation damage responsible for generation of excess carriers is fairly thermostable in the range of annealing temperatures below 800 o C. From deep-level transient spectroscopy measurements, it is found that the radiation damage remains insensitive to changes in carrier concentration. The activation energies of excess carrier generation and removal are estimated from the analysis of the thermal and temporal behaviours of radiation damage in the annealing process. (Author)

Nuclear data for accelerator-driven transmutation. Annual Report 2001/2002

International Nuclear Information System (INIS)

Blomgren, J.; Johansson, C.; Klug, J.; Olsson, N.; Pomp, S.; Renberg, P.U.

2002-07-01

The present project started 1998-07-01. The primary objective from the supporting organizations is to promote research and research education of relevance for development of the national competence within nuclear energy. The aim of the project is in short to: promote development of the competence within nuclear physics and nuclear technology by supporting licentiate and PhD students; push forward the international research front regarding fundamental nuclear data within the presently highlighted research area 'accelerator-driven transmutation'; strengthen the Swedish in influence within the mentioned research area by expanding the international contact network; constitute a basis for Swedish participation in the nuclear data activities at IAEA and OECD/NEA. The project is run by the Department of Neutron Research (INF)at Uppsala University, and is utilizing the unique neutron beam facility at the national The Svedberg Laboratory (TSL) at Uppsala University. Transmutation techniques in accelerator-driven systems (ADS) involve high-energy neutrons, created in the proton-induced spallation of a heavy target nucleus. The existing nuclear data libraries developed for reactors of today go up to about 20 MeV,which covers all available energies for that application; but with a spallator coupled to a core, neutrons with energies up to 1 - 2 GeV will be present. Although a large majority of the neutrons will be below 20 MeV, the relatively small fraction at higher energies still has to be characterized. Above ∼ 200 MeV, direct reaction models work reasonably well, while at lower energies nuclear distortion plays a non-trivial role. This makes the 20 - 200 MeV region the most important for new experimental cross section data. Very little high-quality neutron-induced data exist in this energy domain.Only the total cross section and the np scattering cross section have been investigated extensively. Besides this, there are data on neutron elastic scattering from UC Davis at

A repository released-dose model for the evaluation of long-lived fission product transmutation effectiveness

International Nuclear Information System (INIS)

Davidson, J.W.

1995-01-01

A methodology has been developed to quantify the total integrated dose due to a radionuclide species i emplaced in a geologic repository; the focus is on the seven long-lived fission products (LLFPs). The methodology assumes continuous exposure water contaminated with species i at the accessible environment (i.e., just beyond the geologic barrier afforded by the geologic repository). The dose integration is performed out to a reference post-release time. The integrated dose is a function of the total initial inventory of radionuclide i the repository, the time at which complete and instantaneous failure of the engineered barrier (e.g., waste canister) in, a geologic repository occurs, the fractional dissolution rate (from waste solid form) of radionuclide i in ground water, the ground water travel time to the accessible environment, the retardation factor (sorption on the geologic media) for radionuclide i, the time after radionuclide begins to enter the biosphere. In order to assess relative dose, the ratio of total integrated dose to that for a reference LLFP species j (e.g., 99 Tc) was defined. This ratio is a measure of the relative benefit of transmutation of other LLFPs compared to 99 Tc. This methodology was further developed in order to quantify the integrated dose reduction per neutron utilized for LLFP transmutation in accelerator-driven transmutation technologies (ADTT). This measure of effectiveness is a function of the integrated dose due to LLFP species i, the number of total captures in LLFP species i chain per LLFP nuclide fed to the chain at equilibrium, and the number of total captures in related transmutation product (TP) chains per capture in the LLFP species i chain. To assess relative transmutation effectiveness, the ratio of integrated dose reduction per neutron utilization to that for a reference LLFP species j (e.g., 99 Tc) was defined. This relative measure of effectiveness was evaluated LLFP transmutation strategy

Gas core reactors for actinide transmutation and breeder applications. Annual report

International Nuclear Information System (INIS)

Clement, J.D.; Rust, J.H.

1978-01-01

This work consists of design power plant studies for four types of reactor systems: uranium plasma core breeder, uranium plasma core actinide transmuter, UF6 breeder and UF6 actinide transmuter. The plasma core systems can be coupled to MHD generators to obtain high efficiency electrical power generation. A 1074 MWt UF6 breeder reactor was designed with a breeding ratio of 1.002 to guard against diversion of fuel. Using molten salt technology and a superheated steam cycle, an efficiency of 39.2% was obtained for the plant and the U233 inventory in the core and heat exchangers was limited to 105 Kg. It was found that the UF6 reactor can produce high fluxes (10 to the 14th power n/sq cm-sec) necessary for efficient burnup of actinide. However, the buildup of fissile isotopes posed severe heat transfer problems. Therefore, the flux in the actinide region must be decreased with time. Consequently, only beginning-of-life conditions were considered for the power plant design. A 577 MWt UF6 actinide transmutation reactor power plant was designed to operate with 39.3% efficiency and 102 Kg of U233 in the core and heat exchanger for beginning-of-life conditions

Strong coupling transmutation of Yukawa theory

International Nuclear Information System (INIS)

Chiang, C.C.; Chiu, C.B.; Sudarshan, E.C.G.

1981-01-01

In the strong coupling limit, it is shown that the Yukawa-type theory can be made to undergo a transmutation into an attractive separable potential theory, provided a single state is removed from the spectrum in the lowest nontrivial sector and the states at infinity which include a continuum in the next sector. If these states are not removed, the two theories are distinct. It is suggested that the full equivalence and the renormalization of four-fermion theories need further examination. (orig.)

The DD Cold Fusion-Transmutation Connection

Science.gov (United States)

Chubb, Talbot A.

2005-12-01

LENR theory must explain dd fusion, alpha-addition transmutations, radiationless nuclear reactions, and three-body nuclear particle reactions. Reaction without radiation requires many-body D Bloch+ periodicity in both location and internal structure dependencies. Electron scattering leads to mixed quantum states. The radiationless dd fusion reaction is 2-D Bloch+ -> {}4 He Bloch2+. Overlap between {}4 He Bloch2+ and surface Cs leads to alpha absorption. In the Iwamura et al. studies active deuterium is created by scattering at diffusion barriers.

Keynote address at the international conference on nuclear waste transmutation

International Nuclear Information System (INIS)

Steinberg, M.

1980-07-01

Most of the US research effort on radioactive waste management is concentrated on its solidification and storage in geologic formations. Transmutation is an alternative. It can be applied to weapons plutonium as well to spent fuel

Rationale for a spallation neutron source target system test facility at the 1-MW Long-Pulse Spallation Source

International Nuclear Information System (INIS)

Sommer, W.F.

1995-12-01

The conceptual design study for a 1-MW Long-Pulse Spallation Source at the Los Alamos Neutron Science Center has shown the feasibility of including a spallation neutron test facility at a relatively low cost. This document presents a rationale for developing such a test bed. Currently, neutron scattering facilities operate at a maximum power of 0.2 MW. Proposed new designs call for power levels as high as 10 MW, and future transmutation activities may require as much as 200 MW. A test bed will allow assessment of target neutronics; thermal hydraulics; remote handling; mechanical structure; corrosion in aqueous, non-aqueous, liquid metal, and molten salt systems; thermal shock on systems and system components; and materials for target systems. Reliable data in these areas are crucial to the safe and reliable operation of new high-power facilities. These tests will provide data useful not only to spallation neutron sources proposed or under development, but also to other projects in accelerator-driven transmutation technologies such as the production of tritium

Design Concept of the Thermal Flux Island in MYRRHA for LLFP Transmutation. Present Status

International Nuclear Information System (INIS)

Aoust, Th.; De Raedt, Ch.; Malambu, E.; Ait Abderrahim, H.

2002-01-01

MYRRHA is an ADS aimed at providing protons and neutrons for various R and D applications. It consists of a proton accelerator coupled to a sub-critical fast core. While the fast neutron spectrum, obtaining in the MYRRHA core, allows the transmutation of minor actinides (MAs), the transmutation of long lived fission products (LLFPs) in MYRRHA requires the utilisation of a thermal spectrum in order to take profit of the fact that the capture cross-sections of the LLFPs are much larger in the thermal-energy domain than in the high-energy domain. A high thermal flux island inside MYRRHA is therefore being developed, consisting of an irradiation device for LLFPs (or other irradiation target material needing a thermal neutron spectrum), surrounded by assemblies filled with a lattice of ZrH 2 moderator pins, cooled by the same coolant (Pb-Bi) as the MYRRHA fuel assemblies. Thermal neutron absorbers at the periphery of the neutron island are used to minimise the influence of the thermal flux on the fast core. The study of the performances of MYRRHA, including the transmutation of the LLFPs in such a thermal island, is carried out with the aid of the code MCNPX. The transmutation performances of LLFPs are assessed by coupling the code MCNPX to an evolution calculation. The LLFPs studied are Tc-99 and I-129. (authors)

Monte Carlo analysis of the long-lived fission product neutron capture rates at the Transmutation by Adiabatic Resonance Crossing (TARC) experiment

Energy Technology Data Exchange (ETDEWEB)

Abanades, A., E-mail: abanades@etsii.upm.es [Grupo de Modelizacion de Sistemas Termoenergeticos, ETSII, Universidad Politecnica de Madrid, c/Ramiro de Maeztu, 7, 28040 Madrid (Spain); Alvarez-Velarde, F.; Gonzalez-Romero, E.M. [Centro de Investigaciones Medioambientales y Tecnologicas (CIEMAT), Avda. Complutense, 40, Ed. 17, 28040 Madrid (Spain); Ismailov, K. [Tokyo Institute of Technology, 2-12-1, O-okayama, Meguro-ku, Tokyo 152-8550 (Japan); Lafuente, A. [Grupo de Modelizacion de Sistemas Termoenergeticos, ETSII, Universidad Politecnica de Madrid, c/Ramiro de Maeztu, 7, 28040 Madrid (Spain); Nishihara, K. [Transmutation Section, J-PARC Center, JAEA, Tokai-mura, Ibaraki-ken 319-1195 (Japan); Saito, M. [Tokyo Institute of Technology, 2-12-1, O-okayama, Meguro-ku, Tokyo 152-8550 (Japan); Stanculescu, A. [International Atomic Energy Agency (IAEA), Vienna (Austria); Sugawara, T. [Transmutation Section, J-PARC Center, JAEA, Tokai-mura, Ibaraki-ken 319-1195 (Japan)

2013-01-15

Highlights: Black-Right-Pointing-Pointer TARC experiment benchmark capture rates results. Black-Right-Pointing-Pointer Utilization of updated databases, included ADSLib. Black-Right-Pointing-Pointer Self-shielding effect in reactor design for transmutation. Black-Right-Pointing-Pointer Effect of Lead nuclear data. - Abstract: The design of Accelerator Driven Systems (ADS) requires the development of simulation tools that are able to describe in a realistic way their nuclear performance and transmutation rate capability. In this publication, we present an evaluation of state of the art Monte Carlo design tools to assess their performance concerning transmutation of long-lived fission products. This work, performed under the umbrella of the International Atomic Energy Agency, analyses two important aspects for transmutation systems: moderation on Lead and neutron captures of {sup 99}Tc, {sup 127}I and {sup 129}I. The analysis of the results shows how shielding effects due to the resonances at epithermal energies of these nuclides affects strongly their transmutation rate. The results suggest that some research effort should be undertaken to improve the quality of Iodine nuclear data at epithermal and fast neutron energy to obtain a reliable transmutation estimation.

The irradiation test program for transmutation in the French Phenix fast reactor

International Nuclear Information System (INIS)

Guidez, J.; Chaucheprat, P.; Fontaine, B.; Brunon, E.

2004-01-01

Put on commercial operation in July 1974, the French fast reactor Phenix reached a 100 000 hours operation time in september 2003. When the French law relative to long lived radioactive waste management was promulgated on December 1991, priority was given to Phenix to be run as a research reactor and to carry on a wide irradiation program dedicated to study transmutation of minor actinides and long-lived fission products. After a major renovation program required to extend the reactor lifetime, Phenix power buildup took place in 2003. Experimental irradiations have been loaded in the core, involving components for heterogeneous and homogeneous transmutation modes, americium targets, technetium 99 metal pins and isolated isotopes for integral cross-sections measurements. Associated post- irradiated examination programs are already underway or planned. With new experiments to be loaded in the core in 2006 the Phenix reactor remains to be a powerful tool providing an important experimental data on fast reactors and on transmutation of minor actinides and long-lived fission products, as well as it will contribute to gain further experience in the framework of the GENERATION IV International Forum. (authors)

Hyper fuse: a novel inertial confinement system utilizing hypervelocity projectiles for fusion energy production and fission waste transmutation

International Nuclear Information System (INIS)

Makowitz, H.; Powell, J.R.; Wiswall, R.

1979-01-01

Parametric system studies of an inertial confinement fusion (ICF) reactor system to transmute fission products from an LWR economy have been carried out. The ICF reactors would produce net power in addition to transmuting fission products. The particular ICF concept examined is an impact fusion approach termed HYPERFUSE, in which hypervelocity pellets, traveling on the order of 100 to 300 km/sec, collide with a target in a reactor chamber and initiate a thermonuclear reaction. The DT fusion fuel is contained in a shell of the material to be transmuted, e.g., 137 Cs or 90 Sr. The 14 MeV fusion neutrons released during the pellet burn cause transmutation reactions [e.g., (n, 2n), (n, α), etc.] that convert the long lived fission products (FP's) either to stable products or to species that decay with a short half-life to a stable product

Transmutation of DUPIC spent fuel in the hyper system

International Nuclear Information System (INIS)

Kim, Y.H.; Song, T.Y.

2005-01-01

In this paper, the transmutation of TRUs of the DUPIC (Direct Use of Spent PWR Fuel in CANDU) spent fuel has been studied with the HYPER system, which is an LBE-cooled ADS. The DUPIC concept is a synergistic combination of PWRs and CANDUs, in which PWR spent fuels are directly re-utilized in CANDU reactors after a very simple re-fabrication process. In the DUPIC-HYPER fuel cycle, TRUs are recovered by using a pyro-technology and they are incinerated in a metallic fuel form of U-TRU-Zr. The objective of this study is to investigate the TRU transmutation potential of the HYPER core for the DUPIC-HYPER fuel cycle. All the previously-developed HYPER core design concepts were retained except that fuel is composed of TRU from the DUPIC spent fuel. In order to reduce the burnup reactivity swing, a B 4 C burnable absorber is used. The HYPER core characteristics have been analyzed with the REBUS-3/DIF3D code system. (authors)

Detailed studies of Minor Actinide transmutation-incineration in high-intensity neutron fluxes

International Nuclear Information System (INIS)

Bringer, O.; Al Mahamid, I.; Blandin, C.; Chabod, S.; Chartier, F.; Dupont, E.; Fioni, G.; Isnard, H.; Letourneau, A.; Marie, F.; Mutti, P.; Oriol, L.; Panebianco, S.; Veyssiere, C.

2006-01-01

The Mini-INCA project is dedicated to the measurement of incineration-transmutation chains and potentials of minor actinides in high-intensity thermal neutron fluxes. In this context, new types of detectors and methods of analysis have been developed. The 241 Am and 232 Th transmutation-incineration chains have been studied and several capture and fission cross sections measured very precisely, showing some discrepancies with existing data or evaluated data. An impact study was made on different based-like GEN-IV reactors. It underlines the necessity to proceed to precise measurements for a large number of minor-actinides that contribute to these future incineration scenarios. (authors)

Detailed studies of Minor Actinide transmutation-incineration in high-intensity neutron fluxes

Energy Technology Data Exchange (ETDEWEB)

Bringer, O. [CEA/Saclay/DSM/DAPNIA, Gif-sur-Yvette (France); Al Mahamid, I. [Lawrence Berkeley National Laboratory, E.H. and S. Div., CA (United States); Blandin, C. [CEA/Cadarache/DEN/DER/SPEX, Saint-Paul-lez-Durances (France); Chabod, S. [CEA/Saclay/DSM/DAPNIA, Gif-sur-Yvette (France); Chartier, F. [CEA/Cadarache/DEN/DPC/SECR, Gif-sur-Yvette (France); Dupont, E.; Fioni, G. [CEA/Saclay/DSM/DAPNIA, Gif-sur-Yvette (France); Isnard, H. [CEA/Cadarache/DEN/DPC/SECR, Gif-sur-Yvette (France); Letourneau, A.; Marie, F. [CEA/Saclay/DSM/DAPNIA, Gif-sur-Yvette (France); Mutti, P. [Institut Laue-Langevin, Grenoble (France); Oriol, L. [CEA/Cadarache/DEN/DER/SPEX, Saint-Paul-lez-Durances (France); Panebianco, S.; Veyssiere, C. [CEA/Saclay/DSM/DAPNIA, Gif-sur-Yvette (France)

2006-07-01

The Mini-INCA project is dedicated to the measurement of incineration-transmutation chains and potentials of minor actinides in high-intensity thermal neutron fluxes. In this context, new types of detectors and methods of analysis have been developed. The {sup 241}Am and {sup 232}Th transmutation-incineration chains have been studied and several capture and fission cross sections measured very precisely, showing some discrepancies with existing data or evaluated data. An impact study was made on different based-like GEN-IV reactors. It underlines the necessity to proceed to precise measurements for a large number of minor-actinides that contribute to these future incineration scenarios. (authors)

Innovative materials for GEN IV systems and transmutation facilities (cross-cutting research project GETMAT)

International Nuclear Information System (INIS)

Fazio, Concetta; Rieth, Michael; Gomez Briceno, Dolores; Gessi, Alessandro; Henry, Jean; Malerba, Lorenzo

2010-01-01

The objectives of the 'Generation IV and Transmutation Materials' (GETMAT) project is to contribute to the development, qualification and ranking of different types of ODS steels and to qualify Ferritic/Martensitic steels in a wide irradiation condition range. The experimental approach is complemented by the development of physical models with the aim to understand and improve the predictability of the materials performance. The GETMAT consortium is composed of fourteen Research centres, nine Universities and one Utility, from eleven European countries. The R and D tasks address (i) the materials availability, fabricability, weldability and their fundamental mechanical properties, (ii) their compatibility with aggressive coolants and development of corrosion protection methods; (iii) their performance under neutron irradiation, and (iv) starting from model alloys relevant for the two classes of alloys, the development and validation of physical models. The exploitation of results to potential end-users will occur through the 'GETMAT User Group', where exchange of information with the nuclear and steel industries, international (outside Europe) Research Organisations and engineers involved in the design of the new reactors, will occur. The exploitation of results to potential end-users will occur through the G ETMAT User Group , where exchange of information with the nuclear and steel industries, international (outside Europe) Research Organisations and engineers involved in the design of the new reactors, will occur

A Cost Benefit Analysis of an Accelerator Driven Transmutation System

International Nuclear Information System (INIS)

Westlen, D.; Gudowski, W.; Wallenius, J.; Tucek, K.

2002-01-01

This paper estimates the economical costs and benefits associated with a nuclear waste transmutation strategy. An 800 MWth, fast neutron spectrum, subcritical core design has been used in the study (the so called Sing-Sing Core). Three different fuel cycle scenarios have been compared. The main purpose of the paper has been to identify the cost drivers of a partitioning and transmutation strategy, and to estimate the cost of electricity generated in a nuclear park with operating accelerator driven systems. It has been found that directing all transuranic discharges from spent light water reactor (LWR) uranium oxide (UOX) fuel to accelerator driven systems leads to a cost increase for nuclear power of 50±15%, while introduction of a mixed oxide (MOX) burning step in the LWRs diminishes the cost penalty to 35±10%. (authors)

Implications of transmutation on the defect chemistry in crystalline waste forms

Energy Technology Data Exchange (ETDEWEB)

Uberuaga, B.P., E-mail: blas@lanl.go [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Jiang, C.; Stanek, C.R.; Sickafus, K.E. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Marks, N.A. [Nanochemistry Research Institute, Curtin University of Technology, P.O. Box U1987, Perth, WA 6845 (Australia); Carter, D.J.; Rohl, A.L. [Nanochemistry Research Institute, Curtin University of Technology, P.O. Box U1987, Perth, WA 6845 (Australia); iVEC, Technology Park, Kensington, WA 6151 (Australia)

2010-10-01

Radioactive decay within the solid state creates chemical environments which are typically incommensurate with the initial host structure. Using a combined theoretical and computational approach, we discuss this 'transmutation problem' in the context of the short-lived fission products Cs-137 and Sr-90. We show how a Kroeger-Vink treatment is insufficient for understanding defects arising from transmutation, and present density functional theory data for chemical evolution within two prototypical hosts, CsCl and SrTiO{sub 3}. While the latter has a strong driving force for phase separation with increasing Zr content, the Cs(Ba)Cl system is surprisingly stable. The sharp difference between these two findings points to the need for better understanding of novel chemistry in nuclear waste forms.

The use of thermocouples which transmute during service in nuclear reactors

International Nuclear Information System (INIS)

Martin, R.E.

1980-06-01

Some current nuclear fuel experiments at CRNL require the use of thermocouples to measure temperatures of up to 2200 0 C under reactor operating conditions. A literature search has shown that transient electrical effects and transmutation of the thermocouple alloys can cause temperature measurement errors of up to +-1% and +-30%, respectively. However, the error due to transient electrical effects can be corrected by making temperature measurements immediately following reactor shutdown. Furthermore it has been shown that transmutation effects can be corrected for by calibrating the high temperature tungsten-rhenium thermocouples against a chromel-alumel thermocouple in a cooler part of the experiment. The use of these techniques is expected to reduce temperature measurement errors to +-2% in the best case. (auth)

Conceptual design of a fusion-fission hybrid reactor for transmutation of high level nuclear waste

International Nuclear Information System (INIS)

Qiu, L.J.; Wu, Y.C.; Yang, Y.W.; Wu, Y.; Luan, G.S.; Xu, Q.; Guo, Z.J.; Xiao, B.J.

1994-01-01

To assess the feasibility of the transmutation of long-lived radioactive waste using fusion-fission hybrid reactors, we are studying all the possible types of blanket, including a comparison of the thermal and fast neutron spectrum blankets. Conceptual designs of a small tokamak hybrid blanket with small inventory of actinides and fission products are presented. The small inventory of wastes makes the system safer. The small hybrid reactor system based on a fusion core with experimental parameters to be realized in the near future can effectively transmute actinides and fission products at a neutron wall loading of 1MWm -2 . An innovative energy system is also presented, including a fusion driver, fuel breeder, high level waste transmuter, fission reactor and so on. An optimal combination of all types of reactor is proposed in the system. ((orig.))

Fuel and target programs for the transmutation at Phenix and other reactors; Programmes combustibles et cibles pour la transmutation dans Phenix et autres reacteurs

Energy Technology Data Exchange (ETDEWEB)

Gaillard-Groleas, G

2002-07-01

The fuels and targets program for transmutation, performed in the framework of the axis 1 of the December 1991 law about the researches on the management of long-lived radioactive wastes, is in perfect consistency with the transmutation scenario studies carried out in the same framework. These studies put forward the advantage of fast breeder reactors (FBR) in the incineration of minor actinides and long-lived fission products. The program includes exploratory and technological demonstration studies covering the different design options. It aims at enhancing our knowledge of the behaviour of materials under irradiation and at ensuring the mastery of processes. The goals of the different experiments foreseen at Phenix reactor are presented. The main goal is to supply a set of results allowing to precise the conditions of the technical feasibility of minor actinides and long-lived fission products incineration in FBRs. (J.S.)

Reflection, transmutation, annihilation, and resonance in two-component kink collisions

Science.gov (United States)

Alonso-Izquierdo, A.

2018-02-01

In this paper, the study of collisions between kinks arising in the family of MSTB models is addressed. Phenomena such as elastic kink reflection, mutual annihilation, kink-antikink transmutation and inelastic reflection are found and depend on the impact velocity.

The cross sections of reactions resulting in transmutation of long-lived radionuclides of exhausted nuclear fuel exposed to fast neutrons

International Nuclear Information System (INIS)

Konodeev, A.Yu.; Korovin, Yu.A.; Erview, K.

1993-01-01

Research is at present concerned with the possible transmutation of long-lived radionuclides of spent nuclear fuel in the flux of fast neutrons from neutron generators which are distinguished by their energy spectrum and density of the flux generated. For this purpose one must know the cross sections of the nuclear reactions resulting in the transmutation and formation of new long-lived radionuclides due to the irradiation. The transmutation rate of radioisotope irradiated with neutrons have a known energy spectrum is determined by calculating the transmutation cross section which is equal to the sum of the cross sections of neutron reactions causing conversion of a particular isotope into another after the decay of short-lived residual nuclei. The presently available neutron cross section data of long-lived radionuclides, i.e., the products of the fission of nuclear fuel, are insufficient for research on these effects as transmutations occur in a flux of high-energy neutrons. This paper presents the cross sections of reactions accounting for the transmutation of the most important long-lived radionuclides of exhausted nuclear fuel during its irradiation with neutron having energies of up to 100 MeV. The neutron cross sections were calculated for 79 Se, 90 Sr, 93 Zr, 99 Tc, 107 Pd, 126 Sn, 129 I, 135 Cs and 137 Cs with a half-life ≥30 years

Assessment of the transmutation capability an accelerator driven system cooled by lead bismuth eutectic alloy

International Nuclear Information System (INIS)

Bianchi, F.; Peluso, V.; Calabrese; Chen, X.; Maschek, W.

2007-01-01

1. PURPOSE The reduction of long-lived fission products (LLFP) and minor actinides (MA) is a key point for the public acceptability and economy of nuclear energy. In principle, any nuclear fast reactor is able to burn and transmute MA, but the amount of MA content has to be limited a few percent, having unfavourable consequences on the coolant void reactivity, Doppler effect, and delayed neutron fraction, and therefore on the dynamic behaviour and control. Accelerator Driven Systems (ADS) are instead able to safely burn and/or transmute a large quantity of actinides and LLFP, as they do not rely on delayed neutrons for control or power change and the reactivity feedbacks have very little importance during accidents. Such systems are very innovative being based on the coupling of an accelerator with a subcritical system by means of a target system, where the neutronic source needed to maintain the neutron reaction chain is produced by spallation reactions. To this end the PDS-XADS (Preliminary Design Studies on an experimental Accelerator Driven System) project was funded by the European Community in the 5th Framework Program in order both to demonstrate the feasibility of the coupling between an accelerator and a sub-critical core loaded with standard MOX fuel and to investigate the transmutation capability in order to achieve values suitable for an Industrial Scale Transmuter. This paper summarizes and compares the results of neutronic calculations aimed at evaluating the transmutation capability of cores cooled by Lead-Bismuth Eutectic alloy and loaded with assemblies based on (Pu, Am, Cm) oxide dispersed in a molybdenum metal (CERMET) or magnesia (CERCER) matrices. It also describes the constraints considered in the design of such cores and describes the thermo-mechanical behaviour of these innovative fuels along the cycle. 2. DESCRIPTION OF THE WORK: The U-free composite fuels (CERMET and CERCER) were selected for this study, being considered at European level

Target development and transmutation experiments in the frame of the EFTTRA European collaboration

International Nuclear Information System (INIS)

Prunier, C.; Salvatores, M.; Muehling, G.; Rome, M.

1995-01-01

The aim of the EFTTRA collaboration between CEA (France), ECN (The Netherlands), EDF (France), FZK (Germany), IAM and ITU (European Commission), is to organize joint experiments for the study of materials for transmutation in reactors. The work is focused on the transmutation of 99 Tc (metal), of 129 I (compound), and of Am (in an inert matrix). Irradiation experiments are taking place in parallel in the Phenix fast reactor in France, and in the high flux thermal reactor HFR in the Netherlands. Examination of iodine compounds and Tc samples, following irradiation in HFR, has started. (authors). 10 refs., 2 figs

Transmutation of radioactive nuclear waste – present status and ...

Indian Academy of Sciences (India)

Transmutation of long-lived actinides and fission products becomes an important issue of the overall nuclear fuel cycle assessment, both for existing and future reactor systems. Reliable nuclear data are required for analysis of associated neutronics. The present paper gives a review of the status of nuclear data analysis ...

Conceptual Design of Low Fusion Power Hybrid System for Waste Transmutation

Energy Technology Data Exchange (ETDEWEB)

Hong, Seong Hee; Kim, Myung Hyun [Kyung Hee University, Yongin (Korea, Republic of)

2016-10-15

DRUP (Direct Reuse of Used PWR) fuel has same process with DUPIC (Direct Use of spent PWR fuel Into CANDU reactor). There are 2 big benefits by using DRUP fuel in Hybrid system. One is fissile production during operating period. Required power is decreased by fissile production from DRUP fuel. When the fusion power is reduced, integrity of structure materials is not significantly weakened due to reduction of 14.1MeV high energy neutrons. In addition, required amount of tritium for self-sufficiency TBR (Tritium Breeding Ratio ≥ 1.1) is decreased. Therefore, it is possible to further loading the SNF as much as the amount of lithium decreased. It is effective in transmutation. The other one is that DRUP fuel is also SNF. Therefore, using DRUP fuel is reusing of SNF, as a result it makes reduction of SNF from PWR. However, thermal neutron system is suitable for using DRUP fuel compared to fast neutron system. Therefore, transmutation zone designed (U-TRU)Zr fuel and fissile production zone designed DRUP fuel are separated in this study. In this paper, using DRUP fuel for low fusion power in hybrid system is suggested. Fusion power is decreased by using DRUP fuel. As a result, TBR is satisfied design condition despite of using natural lithium. In addition, not only (U-TRU)Zr fuel but also DRUP fuel are transmuted.

Neutron-transmutation-doped germanium bolometers

Science.gov (United States)

Palaio, N. P.; Rodder, M.; Haller, E. E.; Kreysa, E.

1983-01-01

Six slices of ultra-pure germanium were irradiated with thermal neutron fluences between 7.5 x 10 to the 16th and 1.88 x 10 to the 18th per sq cm. After thermal annealing the resistivity was measured down to low temperatures (less than 4.2 K) and found to follow the relationship rho = rho sub 0 exp(Delta/T) in the hopping conduction regime. Also, several junction FETs were tested for noise performance at room temperature and in an insulating housing in a 4.2 K cryostat. These FETs will be used as first stage amplifiers for neutron-transmutation-doped germanium bolometers.

II. Inhibited Diffusion Driven Surface Transmutations

Science.gov (United States)

Chubb, Talbot A.

2006-02-01

This paper is the second of a set of three papers dealing with the role of coherent partitioning as a common element in Low Energy Nuclear Reactions (LENR), by which is meant cold-fusion related processes. This paper discusses the first step in a sequence of four steps that seem to be necessary to explain Iwamura 2-α-addition surface transmutations. Three concepts are examined: salt-metal interface states, sequential tunneling that transitions D+ ions from localized interstitial to Bloch form, and the general applicability of 2-dimensional vs. 3-dimensional symmetry hosting networks.

II. Inhibited diffusion driven surface transmutations

International Nuclear Information System (INIS)

Cubb, Talbot A.

2006-01-01

This paper is the second of a set of three papers dealing with the role of coherent partitioning as a common element in Low Energy Nuclear Reactions (LENR), by which is meant cold-fusion related processes. This paper discusses the first step in a sequence of four steps that seem to be necessary to explain lwamura 2-α-addition surface transmutations. Three concepts are examined: salt metal interface states, sequential tunneling that transitions D + ions from localized interstitial to Bloch form, and the general applicability of 2-dimensional vs. 3-dimensional symmetry hosting networks. (author)

Nuclear data for accelerator-driven transmutation. Annual report 1999/2000

International Nuclear Information System (INIS)

Atac, A.; Blomgren, J.; Johansson, C.; Klug, J.; Olsson, N.; Renberg, P.U.

2000-09-01

The present project, supported as a research task agreement by SKI, SKB, Barsebaeck Kraft AB and Vattenfall AB, started 1998-07-01. From 1999-01-01 the project also receives support from the Defence Research Establishment. The primary objective from the supporting organizations is to promote research and research education of relevance for development of the national competence within nuclear energy. The aim of the project is in short to: promote development of the competence within nuclear physics and nuclear technology by supporting licentiate and PhD students, push forward the international research front regarding fundamental nuclear data within the presently highlighted research area 'accelerator-driven transmutation', strengthen the Swedish influence within the mentioned research area by expanding the international contact network, constitute a basis for Swedish participation in the nuclear data activities at IAEA and OECD/NEA. The project is run by the Department of Neutron Research at Uppsala University, and is utilizing the unique neutron beam facility at the national The Svedberg Laboratory. In this document, we give a status report after the second year (1999-07-01--2000-06-30) of the project

Estimation of the outlooks for large-scale transmutation of fission-produced iodine

CERN Document Server

Galkin, B Y; Kolyadin, A B; Kocherov, N P; Lyubtsev, R I; Hosov, A A; Rimskij-Korsakov, A A

2002-01-01

To obtain data necessary for estimating sup 1 sup 2 sup 9 I transmutation efficiency in nuclear reactors the effective neutron capture cross section on sup 1 sup 2 sup 9 I isotope in neutral spectrum of the WWR-M reactor was determined. The calculated value of sup 1 sup 2 sup 9 I capture cross section, averaged by neutron spectrum in beryllium reflector of the WWR-M reactor, made up 17.8+-3.2 barn. On the basis of experimental data and estimations it was shown that in neutron flux 10 sup 1 sup 4 1/(cm sup 2 s) transmutation of iodine -129 loaded in the course of one year can amount to approximately 25%

Study of nuclear energy systems and double strata scenarios for minor actinides transmutation in ADS

International Nuclear Information System (INIS)

Clavel, J.B.

2012-01-01

The French law of 28 June 2006 regarding advanced nuclear waste management requires a scientific assessment to define future industrial strategies. The present PhD thesis was carried in this framework and concerns specifically the research axis of minor actinides transmutation. A high power Accelerator Driven System (ADS) concept is developed at SUBATECH for this purpose. A 1 GeV proton beam feeds three liquid lead-bismuth spallation targets. The Multiple Spallation Target (MUST) ADS reaches the thermal powers up to 1 GW with a high specific power. A nuclear reactor dimensioning method has been developed and applied to different double strata scenarios. In these scenarios, SFR (Sodium Fast Reactors) or PWR (Pressurized Water Reactors) power reactors produce minor actinides that will be transmuted into ADS. In each core (SFR and ADS), the plutonium multi-reprocessing strategy is performed while ADS subcritical core also multi-reprocesses minor actinides. To limit the core reactivity and improve the fuel thermal conductivity, the minor actinides fuel is mixed with MgO inert matrix. Nuclear branches with lead and sodium coolants for the ADS, have been studied for different irradiation times and two transmutation strategies have been assessed: whether whole minor actinides, whether americium only is transmuted. The thesis presents precisely the MUST ADS design methodology and the calculations to get a fuel composition at equilibrium. Then a one cycle evolution is performed and analysed for the fuel and the multiplication factor. Radiotoxicity and thermal power of the waste produced are then compared. Finally, the study of double strata scenarios is performed to analyse the plutonium and minor actinides inventories in cycle and also the waste produced according to the transmutation strategies applied and the first stratum evolution. (author)

APEX accelerator cycle for transmutation of long-lived fission wastes

International Nuclear Information System (INIS)

Powell, J.; Steinberg, M.; Takahashi, H.; Grand, P.; Botts, T.; Kouts, H.J.C.

1980-01-01

Based on preliminary studies, some conclusions can be drawn concerning the Accelerator Fuel Enricher and Fission Product Exterminator (APEX). APEX-1 and APEX-2 systems can destroy TU's, 137 Cs, and 90 Sr at acceptable cost and efficiency. The principal difference between APEX-1 and APEX-2 is the in-reactor and in-circuit inventory of 137 Cs and 90 Sr. Stable and low hazard wastes can be disposed of by burial. Accelerator breeders can effectively sustain a fission reactor economy indefinitely. Military waste can be blended into commercial fuel cycle for transmutation. Accelerator and target technologies appear practical and could be developed in a few years. More detailed studies are needed to better define the technical and economic features of the LAFER and APEX cycles, so that comparative assessments can be made between these cycles, as well as with other transmutation and waste disposal concepts

Study on partitioning and transmutation as a possible option for spent fuel management within a nuclear phase-out scenario

Energy Technology Data Exchange (ETDEWEB)

Fazion, C.; Rineiski, A.; Salvatores, M.; Schwenk-Ferrero, A.; Romanello, V.; Vezzoni, B.; Gabrielli, F. [Karlsruhe Institute of Technology - KIT, Hermann-von-Helmholtz Platz 1, 76344 Eggenstein-Leopoldshafen (Germany)

2013-07-01

Most Partitioning and Transmutation (PT) studies implicitly presuppose the continuous use of nuclear energy. In this case the development of new facilities or the modification of the fuel cycle can be justified in the long-term as an important feature in order to improve sustainability by minimizing radioactive waste and reducing the burden at waste disposal. In the case of a country with nuclear energy phase-out policy, the PT option might have also an important role for what concerns the final disposal strategies of the spent fuel. In this work three selected scenarios are analyzed in order to assess the impact of PT implementation in a nuclear energy phase out option. The scenarios are: -) Scenario 1: Identification of Research/Development activities needs for a technological development of PT while postponing the decision of PT implementation; -) Scenario 2: Isolated application of PT in a phase-out context; and -) Scenario 3: Implementation of PT in a European context. In order to facilitate the discrimination among the 3 scenarios, a number of figures of indicators have been evaluated for each scenario. The selected indicators are: the mass of High Level Waste (HLW), Uranium inventory, thermal output of HLW, Radiotoxicity, Fuel cycle secondary waste associated to the PT operation, and Facility capacity/number requirements. The reduction, due to PT implementation, of high level wastes masses and their associated volumes can be significant. For what concerns the thermal output and radiotoxicity a significant impact can be also expected. However, when assessing these two indicators the contribution coming from already vitrified waste should also not be neglected. Moreover, an increase of secondary waste inventory is also expected. On the contrary, the increase of fission product inventories due to the operation of the transmutation system has a relatively limited impact on the fuel cycle.

Microbial transmutation of 137Cs and LENR in growing biological systems

International Nuclear Information System (INIS)

Vysotskii, V.I.; Kornilova, A.A.

2015-01-01

This article presents the results of long-term investigations of stable and radioactive isotopes transmutation in growing microbiological cultures. It is shown that transmutation during growth of microbiological associations is 20 times more effective than the same process in the form of 'clean' microbiological culture. In this work, the process of controlled decontamination of highly active reactor isotopes (reactor waste) through the process of growing microbiological associations has been studied. The most rapidly increasing decay rate of 137 Cs isotope, which occurred with the 'effective' half life τ* ≈ 310 days (involving an increase in rate and decrease in half life by a factor of 35) was observed in the presence of Ca salt in closed flask with active water containing 137 Cs solution and optimal microbiological association. (author)

Automatically controlled facilities for irradiation of silicon crystals at the Rossendorf Research Reactor

International Nuclear Information System (INIS)

Ross, R.

1988-01-01

This report describes the facilities for neutron transmutation doping of silicon in GDR. The irradiation of silicon single crystals began at Rossendorf in 1978 with simple equipment. Only a small amount of silicon could be irradiated in it. The fast increasing need of NTD-silicon made it necessary to design and construct new and better facilities. The new facilities are capable of irradiating silicon from 2'' to 3'' in diameter. The irradiation process takes place automatically with the assistance of a computer. Material produced has an axial homogeneity of ± 7%. Irradiation riggs, techniques, irradiation control and quality control are discussed. (author). 4 figs

Reduction and resource recycling of high-level radioactive wastes through nuclear transmutation with PHITS code

International Nuclear Information System (INIS)

Fujita, Reiko

2017-01-01

In the ImPACT program of the Cabinet Office, programs are underway to reduce long-lived fission products (LLFP) contained in high-level radioactive waste through nuclear transmutation, or to recycle/utilize useful nuclear species. This paper outlines this program and describes recent achievements. This program consists of five projects: (1) separation/recovery technology, (2) acquisition of nuclear transmutation data, (3) nuclear reaction theory model and simulation, (4) novel nuclear reaction control and development of elemental technology, and (5) discussions on process concept. The project (1) develops a technology for dissolving vitrified solid, a technology for recovering LLFP from high-level waste liquid, and a technology for separating odd and even lasers. Project (2) acquires the new nuclear reaction data of Pd-107, Zr-93, Se-79, and Cs-135 using RIKEN's RIBF or JAEA's J-PARC. Project (3) improves new nuclear reaction theory and structural model using the nuclear reaction data measured in (2), improves/upgrades nuclear reaction simulation code PHITS, and proposes a promising nuclear transmutation pathway. Project (4) develops an accelerator that realizes the proposed transmutation route and its elemental technology. Project (5) performs the conceptual design of the process to realize (1) to (4), and constructs the scenario of reducing/utilizing high-level radioactive waste to realize this design. (A.O.)

Monte Carlo method in ADS transmutation reactor coolant and the research of optimal placement of the fuel

International Nuclear Information System (INIS)

Niu Yunlong; Wei Qianglin; Liu Yibao; Wang Aixing; Zhang Peng

2014-01-01

This paper calculated the effects of different coolants to neutron energy spectrum in different position of the transmutation reactor by Monte Carlo N-Particle Transport Code (MCNP5). After having chosen the coolant and particular parameters, different nuclides in fuel rods of the transmutation reactor were calculated and compared. According to the actual situation, nuclides of 99 Tc and 241 Am were chosen and compared. Then the nonuniform-arrangement scheme of different spent fuels were proposed. By comparison of the diagram, it is found that it is more effective to promote the neutron utilization in the reactor by the non-uniform arrangement scheme, which is more reasonable than traditional uniform one. Thus, it would be helpful for transmutation technology by the application of the scheme. (authors)

On the use of a molten salt fast reactor to apply an idealized transmutation scenario for the nuclear phase out.

Directory of Open Access Journals (Sweden)

Bruno Merk

Full Text Available In the view of transmutation of transuranium (TRU elements, molten salt fast reactors (MSFRs offer certain advantages compared to solid fuelled reactor types like sodium cooled fast reactors (SFRs. In the first part these advantages are discussed in comparison with the SFR technology, and the research challenges are analyzed. In the second part cycle studies for the MSFR are given for different configurations--a core with U-238 fertile, a fertile free core, and a core with Th-232 as fertile material. For all cases, the transmutation potential is determined and efficient transmutation performance for the case with thorium as a fertile material as well as for the fertile free case is demonstrated and the individual advantages are discussed. The time evolution of different important isotopes is analyzed. In the third part a strategy for the optimization of the transmutation efficiency is developed. The final aim is dictated by the phase out decision of the German government, which requests to put the focus on the determination of the maximal transmutation efficiency and on an as much as possible reduced leftover of transuranium elements at the end of the reactor life. This minimal leftover is achieved by a two step procedure of a first transmuter operation phase followed by a second deep burning phase. There the U-233, which is bred in the blanket of the core consisting of thorium containing salt, is used as feed. It is demonstrated, that transmutation rates up to more than 90% can be achieved for all transuranium isotopes, while the production of undesired high elements like californium is very limited. Additionally, the adaptations needed for the simulation of a MSFR, and the used tool HELIOS 1.10 is described.

On the use of a molten salt fast reactor to apply an idealized transmutation scenario for the nuclear phase out.

Science.gov (United States)

Merk, Bruno; Rohde, Ulrich; Glivici-Cotruţă, Varvara; Litskevich, Dzianis; Scholl, Susanne

2014-01-01

In the view of transmutation of transuranium (TRU) elements, molten salt fast reactors (MSFRs) offer certain advantages compared to solid fuelled reactor types like sodium cooled fast reactors (SFRs). In the first part these advantages are discussed in comparison with the SFR technology, and the research challenges are analyzed. In the second part cycle studies for the MSFR are given for different configurations--a core with U-238 fertile, a fertile free core, and a core with Th-232 as fertile material. For all cases, the transmutation potential is determined and efficient transmutation performance for the case with thorium as a fertile material as well as for the fertile free case is demonstrated and the individual advantages are discussed. The time evolution of different important isotopes is analyzed. In the third part a strategy for the optimization of the transmutation efficiency is developed. The final aim is dictated by the phase out decision of the German government, which requests to put the focus on the determination of the maximal transmutation efficiency and on an as much as possible reduced leftover of transuranium elements at the end of the reactor life. This minimal leftover is achieved by a two step procedure of a first transmuter operation phase followed by a second deep burning phase. There the U-233, which is bred in the blanket of the core consisting of thorium containing salt, is used as feed. It is demonstrated, that transmutation rates up to more than 90% can be achieved for all transuranium isotopes, while the production of undesired high elements like californium is very limited. Additionally, the adaptations needed for the simulation of a MSFR, and the used tool HELIOS 1.10 is described.

The EU research activities on partitioning and transmutation. From the 4. to the 5. framework programme

International Nuclear Information System (INIS)

Hugon, M.

1999-01-01

The European Commission is partly supporting research work on partitioning and transmutation of radioactive waste under the Fourth Framework Programme (1994-1998). This work includes nine research projects. Five strategy studies are evaluating the capabilities of various burners and fuel cycles to limit the production and even destroy the stock of actinides (plutonium and minor actinides). Two experimental projects are aiming at developing techniques for the chemical separation of actinides and two others are dealing with the investigation of transmutation of americium and long-lived fission products. The objectives of these studies are described together with the main results already obtained. The European Union should adopt the 5. Framework Programme (1998-2002) at the end of 1998. The broad lines of the research activities foreseen in partitioning and transmutation and future system under the 5. Framework Programme are briefly presented. (author)

Effect of Fast Neutron to MA/PU Burning/Transmutation Characteristic Using a Fast Reactor

International Nuclear Information System (INIS)

Marsodi; Lasman, As Natio; Kimamoto, A.; Marsongkohadi; Zaki, S.

2003-01-01

MA/Pu burning/transmutation has been studied and evaluated using fast neutrons. Generally, neutron density at this fast burner reactor and transmutation has spectrum energy level around 0.2 MeV with wide enough variation, i.e. from low neutron spectrum to its peak is 0.2 MeV. This neutron spectrum energy level depends on the kind of cooler material or fuel used. Neutron spectrum higher than fast power reactor neutron spectrum is found by means of changing oxide fuel by metallic fuel and changing natrium cooler material by metallic or gas cooler material. This evaluation is conducted by various variations in accordance with the kind of fuel or cooler, MA/Pu fractions and fuel comparison fraction with respect to its cooler in order to get better neutron usage and MA/Pu burning speed. Reactor calculation evaluation in this paper was conducted with 26-group nuclear data cross section energy spectrum. The main purpose of the discussion is to know the effect of fast neutrons to burning/transmutation MA/Pu using fast neutrons

A code system for ADS transmutation studies

International Nuclear Information System (INIS)

Brolly, A.; Vertes, P.

2001-01-01

An accelerator driven reactor physical system can be divided into two different subsystems. One is the neutron source the other is the subcritical reactor. Similarly, the modelling of such system is also split into two parts. The first step is the determination of the spatial distribution and angle-energy spectrum of neutron source in the target region; the second one is the calculation of neutron flux which is responsible for the transmutation process in the subcritical system. Accelerators can make neutrons from high energy protons by spallation or photoneutrons from accelerated electrons by Bremsstrahlung (e-n converter). The Monte Carlo approach is the only way of modelling such processes and it might be extended to the whole subcritical system as well. However, a subcritical reactor may be large, it may contain thermal regions and the lifetime of neutrons may be long. Therefore a comprehensive Monte Carlo modelling of such system is a very time consuming computational process. It is unprofitable as well when applied to system optimization that requires a comparative study of large number of system variants. An appropriate method of deterministic transport calculation may adequately satisfy these requirements. Thus, we have built up a coupled calculational model for ADS to be used for transmutation of nuclear waste which we refer further as M-c-T system. Flow chart is shown in Figure. (author)

Partitioning and Transmutation. Annual Report 2005

Energy Technology Data Exchange (ETDEWEB)

Andersson, Sofie; Ekberg, Christian; Fermvik, Anna; Hervieux, Nadege; Liljenzin, Jan-Olov; Magnusson, Daniel; Nilsson, Mikael; Retegan, Teodora; Skarnemark, Gunnar [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Chemical and Biological Engineering

2006-01-15

The long-lived elements in the spent nuclear fuels are mostly actinides, some fission products ({sup 79}Se, {sup 87}Rb, {sup 99}Tc, {sup 107}Pd, {sup 126}Sn, {sup 129}I, {sup 135}Cs) and activation products ({sup 14}C, {sup 36}Cl, {sup 59}Ni, {sup 93}Zr, {sup 94}N To be able to destroy the long-lived elements in a transmutation process they must be separated from the rest of the spent nuclear fuel. The most difficult separations to make are those between trivalent actinides and lanthanides, due to their relatively similar chemical properties, and those between different actinides themselves. These separations are necessary to obtain the desired efficiency of the transmutation process and in order not to create any unnecessary waste thus rendering the process useless. Solvent extraction is an efficient and well-known method that makes it possible to have separation factors that fulfil the highly set demands on purity of the separated phases and on small losses. Chalmers Univ. of Technology is involved in research regarding the separation of actinides and lanthanides and between the actinides themselves as a partner in the EUROPART project within the European Union sixth framework program. This is a continuation of the projects we participated in within the fourth and fifth framework programmes, NEWPART and PARTNEW respectively. The aims of the projects have now shifted from basic understanding to more applied research with focus on process development. However, since the basic understanding is still needed we have our main focus on the chemical processes and understanding of how they work.

Partitioning and Transmutation. Annual Report 2005

International Nuclear Information System (INIS)

Andersson, Sofie; Ekberg, Christian; Fermvik, Anna; Hervieux, Nadege; Liljenzin, Jan-Olov; Magnusson, Daniel; Nilsson, Mikael; Retegan, Teodora; Skarnemark, Gunnar

2006-01-01

The long-lived elements in the spent nuclear fuels are mostly actinides, some fission products ( 79 Se, 87 Rb, 99 Tc, 107 Pd, 126 Sn, 129 I, 135 Cs) and activation products ( 14 C, 36 Cl, 59 Ni, 93 Zr, 94 N To be able to destroy the long-lived elements in a transmutation process they must be separated from the rest of the spent nuclear fuel. The most difficult separations to make are those between trivalent actinides and lanthanides, due to their relatively similar chemical properties, and those between different actinides themselves. These separations are necessary to obtain the desired efficiency of the transmutation process and in order not to create any unnecessary waste thus rendering the process useless. Solvent extraction is an efficient and well-known method that makes it possible to have separation factors that fulfil the highly set demands on purity of the separated phases and on small losses. Chalmers Univ. of Technology is involved in research regarding the separation of actinides and lanthanides and between the actinides themselves as a partner in the EUROPART project within the European Union sixth framework program. This is a continuation of the projects we participated in within the fourth and fifth framework programmes, NEWPART and PARTNEW respectively. The aims of the projects have now shifted from basic understanding to more applied research with focus on process development. However, since the basic understanding is still needed we have our main focus on the chemical processes and understanding of how they work

Classical Dimensional Transmutation and Confinement

CERN Document Server

Dvali, Gia; Mukhanov, Slava

2011-01-01

We observe that probing certain classical field theories by external sources uncovers the underlying renormalization group structure, including the phenomenon of dimensional transmutation, at purely-classical level. We perform this study on an example of $\\lambda\\phi^{4}$ theory and unravel asymptotic freedom and triviality for negative and positives signs of $\\lambda$ respectively. We derive exact classical $\\beta$ function equation. Solving this equation we find that an isolated source has an infinite energy and therefore cannot exist as an asymptotic state. On the other hand a dipole, built out of two opposite charges, has finite positive energy. At large separation the interaction potential between these two charges grows indefinitely as a distance in power one third.

Impact of partitioning and transmutation on high-level waste disposal for the fast breeder reactor fuel cycle

International Nuclear Information System (INIS)

Nishihara, Kenji; Oigawa, Hiroyuki; Nakayama, Shinichi; Ono, Kiyoshi; Shiotani, Hiroki

2010-01-01

The impact of partitioning and/or transmutation (PT) technology on high-level waste management was investigated for the equilibrium state of several potential fast breeder reactor (FBR) fuel cycles. Three different fuel cycle scenarios involving PT technology were analyzed: 1) partitioning process only (separation of some fission products), 2) transmutation process only (separation and transmutation of minor actinides), and 3) both partitioning and transmutation processes. The conventional light water reactor (LWR) fuel cycle without PT technology, on which the current repository design is based, was also included for comparison. We focused on the thermal constraints in a geological repository and determined the necessary predisposal storage quantities and time periods (by defining a storage capacity index) for several predefined emplacement configurations through transient thermal analysis. The relation between this storage capacity index and the required repository emplacement area was obtained. We found that the introduction of the FBR fuel cycle without PT can yield a 35% smaller repository per unit electricity generation than the LWR fuel cycle, although the predisposal storage period is prolonged from 50 years for the LWR fuel cycle to 65 years for the FBR fuel cycle without PT. The introduction of the partitioning-only process does not result in a significant reduction of the repository emplacement area from that for the FBR fuel cycle without PT, but the introduction of the transmutation-only process can reduce the emplacement area by a factor of 5 when the storage period is extended from 65 to 95 years. When a coupled partitioning and transmutation system is introduced, the repository emplacement area can be reduced by up to two orders of magnitude by assuming a predisposal storage of 60 years for glass waste and 295 years for calcined waste containing the Sr and Cs fraction. The storage period of 295 years for the calcined waste does not require a large

A Comparison of Laser-induced Bremsstrahlung and Laser Compton Scattering for (γ, n) Photo-transmutation of Hazardous Nuclear Waste

International Nuclear Information System (INIS)

Rehman, Haseeb ur; Lee, Jiyoung; Kim, Yonghee

2015-01-01

This paper also presents sensitivity analysis to yield the maximum possible photo-transmutation rates. In general the possibility of radionuclide transmutation using photo-neutron reaction is evaluated in this work. In this paper a detailed methodology to calculate transmutation reaction rates using Laser Induced Bremsstrahlung (LIB) and Laser Compton Scattering (LCS) has been discussed. The methodology was validated by comparing the calculated reaction rates against published data in publically accessed literatures. In the second half of the paper, the authors present a novel concept to narrow down the LCS photon spectrum to an energy range that matches with the resonance region of a particular radionuclide. This is particularly useful considering hazardous waste is usually a mix of different isotopes. As such, being able to tune the LCS photon into any narrow energy range so as to selectively transmute any particular isotope of interest in the hazardous waste mixture would be very desirable. LCS spectrum is highly sensitive to the electron beam energy, laser power, laser luminosity and Compton backscattering angle. From the results it is quite evident that LCS is much better option for the radionuclide transmutation as reaction rates for the LCS is much higher than LIB method even for very small laser power. It can be seen even for the optimistic reaction rate calculations with Bremsstrahlung method reaction rate is much lower than LCS case for 10 Hz repetition rate. If repetition rate of laser 100 Hz then LIB reaction rate has the same order of the magnitude as the reaction rate via LCS. Higher Laser Powers can yield very high transmutation rates

Fast molten salt reactor-transmuter for closing nuclear fuel cycle on minor actinides

International Nuclear Information System (INIS)

Dudnikov, A. A.; Alekseev, P. N.; Subbotin, S. A.

2007-01-01

Creation fast critical molten salt reactor for burning-out minor actinides and separate long-living fission products in the closed nuclear fuel cycle is the most perspective and actual direction. The reactor on melts salts - molten salt homogeneous reactor with the circulating fuel, working as burner and transmuter long-living radioactive nuclides in closed nuclear fuel cycle, can serve as an effective ecological cordon from contamination of the nature long-living radiotoxic nuclides. High-flux fast critical molten-salt nuclear reactors in structure of the closed nuclear fuel cycle of the future nuclear power can effectively burning-out / transmute dangerous long-living radioactive nuclides, make radioisotopes, partially utilize plutonium and produce thermal and electric energy. Such reactor allows solving the problems constraining development of large-scale nuclear power, including fueling, minimization of radioactive waste and non-proliferation. Burning minor actinides in molten salt reactor is capable to facilitate work solid fuel power reactors in system NP with the closed nuclear fuel cycle and to reduce transient losses at processing and fabrications fuel pins. At substantiation MSR-transmuter/burner as solvents fuel nuclides for molten-salt reactors various salts were examined, for example: LiF - BeF2; NaF - LiF - BeF2; NaF-LiF ; NaF-ZrF4 ; LiF-NaF -KF; NaCl. RRC 'Kurchatov institute' together with other employees have developed the basic design reactor installations with molten salt reactor - burner long-living nuclides for fluoride fuel composition with the limited solubility minor actinides (MAF3 10 mol %) allows to develop in some times more effective molten salt reactor with fast neutron spectrum - burner/ transmuter of the long-living radioactive waste. In high-flux fast reactors on melts salts within a year it is possible to burn ∼300 kg minor actinides per 1 GW thermal power of reactor. The technical and economic estimation given power

System and safety studies of accelerator driven transmutation. Annual Report 2001

International Nuclear Information System (INIS)

Gudowski, W.; Wallenius, J.; Tucek, K.; Eriksson, Marcus; Carlsson, Johan; Seltborg, P.; Cetnar, J.; Chakarova, R.; Westlen, D.

2002-03-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the Dept. of Nuclear and Reactor Physics has been focused in year 2001 on: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features; b) analysis of ADS-dynamics; c) computer code and nuclear data development relevant for simulation and optimization of ADS; d) participation in ADS experiments including 1 MW spallation target manufacturing, subcritical experiments MUSE (CEA-Cadarache) and YALINA experiment in Minsk. The Dept. is very actively participating in many European projects in the 5th Framework Programme of the European Community. Most of the research topics reported in this paper are referred to by appendices, which have been published in the open literature. The topics, which are not yet published, are described here in more details

System and safety studies of accelerator driven transmutation. Annual Report 2001

Energy Technology Data Exchange (ETDEWEB)

Gudowski, W; Wallenius, J; Tucek, K; Eriksson, Marcus; Carlsson, Johan; Seltborg, P; Cetnar, J; Chakarova, R; Westlen, D [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

2002-03-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the Dept. of Nuclear and Reactor Physics has been focused in year 2001 on: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features; b) analysis of ADS-dynamics; c) computer code and nuclear data development relevant for simulation and optimization of ADS; d) participation in ADS experiments including 1 MW spallation target manufacturing, subcritical experiments MUSE (CEA-Cadarache) and YALINA experiment in Minsk. The Dept. is very actively participating in many European projects in the 5th Framework Programme of the European Community. Most of the research topics reported in this paper are referred to by appendices, which have been published in the open literature. The topics, which are not yet published, are described here in more details.

II. Inhibited diffusion driven surface transmutations

Energy Technology Data Exchange (ETDEWEB)

Cubb, Talbot A. [Greenwich Corp., 5023 N. 38th St., Arlington, VA 22207 (United States)

2006-07-01

This paper is the second of a set of three papers dealing with the role of coherent partitioning as a common element in Low Energy Nuclear Reactions (LENR), by which is meant cold-fusion related processes. This paper discusses the first step in a sequence of four steps that seem to be necessary to explain lwamura 2-{alpha}-addition surface transmutations. Three concepts are examined: salt metal interface states, sequential tunneling that transitions D{sup +} ions from localized interstitial to Bloch form, and the general applicability of 2-dimensional vs. 3-dimensional symmetry hosting networks. (author)

An overview of FFTF [Fast Flux Test Facility] contributions to Liquid Metal Reactor Safety

International Nuclear Information System (INIS)

Waltar, A.E.; Padilla, A. Jr.

1990-11-01

The Fast Flux Test Facility has provided a very useful framework for testing the advances in Liquid Metal Reactor Safety Technology. During the licensing phase, the switch from a nonmechanistic bounding technique to the mechanistic approach was developed and implemented. During the operational phase, the consideration of new tests and core configurations led to use of the anticipated-transients-without-scram approach for beyond design basis events and the move towards passive safety. The future role of the Fast Flux Test Facility may involve additional passive safety and waste transmutation tests. 26 refs

Proceedings of the Eleventh Information Exchange Meeting on Actinide and Fission Product Partitioning and Transmutation

International Nuclear Information System (INIS)

2012-01-01

Partitioning and transmutation (P and T) is one of the key technologies for reducing the radiotoxicity and volume of radioactive waste arisings. Recent developments indicate the need for embedding P and T strategies in advanced fuel cycles considering both waste management and economic issues. In order to provide experts a forum to present and discuss state-of-the-art developments in the P and T field, the OECD/NEA has been organising biennial information exchange meetings on actinide and fission product partitioning and transmutation since 1990. The previous meetings were held in Mito (Japan) in 1990, at Argonne (United States) in 1992, in Cadarache (France) in 1994, in Mito (Japan) in 1996, in Mol (Belgium) in 1998, in Madrid (Spain) in 2000, in Jeju (Korea) in 2002, in Las Vegas (United States) in 2004, in Nimes (France) in 2006 and in Mito (Japan) in 2008. They have often been co-sponsored by the European Commission (EC) and the International Atomic Energy Agency (IAEA). The 11. Information Exchange Meeting was held in San Francisco, California, United States on 1-4 November 2010, comprising a plenary session on national P and T programmes and six technical sessions covering various fields of P and T. The meeting was hosted by the Idaho National Laboratory (INL), United States. The information exchange meetings on P and T form an integral part of NEA activities on advanced nuclear fuel cycles. The meeting covered scientific as well as strategic/policy developments in the field of P and T, such as: fuel cycle strategies and transition scenarios; radioactive waste forms; the impact of P and T on geological disposal; radioactive waste management strategies (including secondary wastes); transmutation fuels and targets; pyro and aqueous separation processes; materials, spallation targets and coolants; transmutation physics, experiments and nuclear data; transmutation systems (design, performance and safety); handling and transportation of transmutation fuels; and

Transmutation of high level nuclear waste in an accelerator driven system: towards a demonstration device of industrial interest (EUROTRANS)

International Nuclear Information System (INIS)

Knebel, Joachim U.; Ait Abderrahim, Hamid; Caron-Carles, Marylise

2010-01-01

The Integrated Project EUROTRANS (EURopean Research Programme for the TRANSmutation of High Level Nuclear Waste in an Accelerator Driven System) within the ongoing EURATOM 6th Framework Programme (FP6) is devoted to the study of transmutation of high-level waste from nuclear power plants. The work is focused on transmutation in an Accelerator Driven System (ADS). The objective of EUROTRANS is the assessment of the design and the feasibility of an industrial ADS prototype dedicated to transmutation. The necessary R and D results in the areas of accelerator components, fuel development, structural materials, thermal-hydraulics, heavy liquid metal technology and nuclear data will be made available, together with the experimental demonstration of the ADS component coupling. The outcome of this work will allow to provide a reasonably reliable assessment of technological feasibility and a cost estimate for ADS based transmutation, and to possibly decide on the detailed design of an experimental ADS and its construction in the future. EUROTRANS is integrating activities of 51 participants from 16 countries, within the industry (10 participants), the national research centres (20) and 17 universities. 16 universities are collectively represented by ENEN (European Nuclear Education Network). EUROTRANS is the continuation of the three FP5 Clusters FUETRA, BASTRA and TESTRA together with the PDS-XADS Project. It is a five-year project which started in April 2005

Grouping in partitioning of HLW for burning and/or transmutation with nuclear reactors

International Nuclear Information System (INIS)

Kitamoto, Asashi; Mulyanto.

1995-01-01

A basic concept on partitioning and transmutation treatment by neutron reaction was developed in order to improve the waste management and the disposal scenario of high level waste (HLW). The grouping in partitioning was important factor and closely linked with the characteristics of B/T (burning and/or transmutation) treatment. The selecting and grouping concept in partitioning of HLW was proposed herein, such as Group MA1 (Np, Am, and unrecovered U and Pu), Group MA2 (Cm, Cf etc.), Group A (Tc and I), Group B (Cs and Sr) and Group R (the partitioned remain of HLW), judging from the three criteria for B/T treatment proposed in this study, which is related to (1) the value of hazard index for long-term tendency based on ALI, (2) the relative dose factor related to the mobility or retardation in ground water penetrated through geologic layer, and (3) burning and/or transmutation characteristics for recycle B/T treatment and the decay acceleration ratio by neutron reaction. Group MA1 and Group A could be burned effectively by thermal B/T reactor. Group MA2 could be burned effectively by fast B/T reactor. Transmutation of Group B by neutron reaction is difficult, therefore the development of radiation application of Group B (Cs and Sr) in industrial scale may be an interesting option in the future. Group R, i.e. the partitioned remains of HLW, and also a part of Group B should be immobilized and solidified by the glass matrix. HI ALI , the hazard index based on ALI, due to radiotoxicity of Group R can be lower than HI ALI due to standard mill tailing (smt) or uranium ore after about 300 years. (author)

Prompt nuclear analytical techniques for material research in accelerator driven transmutation technologies: Prospects and quantitative analyses

International Nuclear Information System (INIS)

Vacik, J.; Hnatowicz, V.; Cervena, J.; Perina, V.; Mach, R.

1998-01-01

Accelerator driven transmutation technology (ADTT) is a promising way toward liquidation of spent nuclear fuel, nuclear wastes and weapon grade Pu. The ADTT facility comprises a high current (proton) accelerator supplying a sub-critical reactor assembly with spallation neutrons. The reactor part is supposed to be cooled by molten fluorides or metals which serve, at the same time, as a carrier of nuclear fuel. Assumed high working temperature (400-600 C) and high radiation load in the subcritical reactor and spallation neutron source put forward the problem of optimal choice of ADTT construction materials, especially from the point of their radiation and corrosion resistance when in contact with liquid working media. The use of prompt nuclear analytical techniques in ADTT related material research is considered and examples of preliminary analytical results obtained using neutron depth profiling method are shown for illustration. (orig.)

Accelerator Driven Sub-Critical System for the Radioactive Waste Transmutation

International Nuclear Information System (INIS)

Avramovic, I.; Pesic, M.

2008-01-01

Spent nuclear fuel discharged from nuclear power plants is the main problem during design of radioactive waste disposal. Most of the hazard stems from only a few chemical elements. The radiotoxicity of these elements can be efficiently reduced using partitioning and transmutation in fast reactors and accelerator driven subcritical systems. (author)

Analytical approach to the evaluation of nuclide transmutations

International Nuclear Information System (INIS)

Vukadin, Z.; Osmokrovic, P.

1995-01-01

Analytical approach to the evaluation of nuclide concentrations in a transmutation chain is presented. Non singular Bateman coefficients and depletion functions are used to overcome numerical difficulties when applying well-known Bateman solution of a simple radioactive decay. Method enables evaluation of complete decay chains without elimination of short lived radionuclides. It is efficient and accurate. Practical application of the method is demonstrated by computing the neptunium series inventory in used Candu TM fuel. (author)

Accelerator technology for Los Alamos nuclear-waste-transmutation and energy-production concepts

International Nuclear Information System (INIS)

Lawrence, G.P.; Jameson, R.A.; Schriber, S.O.

1991-01-01

Powerful proton linacs are being studied at Los Alamos as drivers for high-flux neutron sources that can transmute long-lived fission products and actinides in defense nuclear waste, and also as drivers of advanced fission-energy systems that could generate electric power with no long-term waste legacy. A transmuter fed by an 800-MeV, 140-mA cw conventional copper linac could destroy the accumulated 99 Tc and 129 I at the DOE's Hanford site within 30 years. A high-efficiency 1200-MeV, 140-mA niobium superconducting linac could drive an energy-producing system generating 1-GWe electric power. Preliminary design concepts for these different high-power linacs are discussed, along with the principal technical issues and the status of the technology base. 9 refs., 5 figs., 4 tabs

Neutron transmutation doping

Energy Technology Data Exchange (ETDEWEB)

Jun, Byung Jin

2001-09-01

HE OVERALL STATE OF THE ART RELATED WITH NEUTRON TRANSMUTATION DOPING(NCT) IS SURVEYED. ITEMS RELATED FOR THE REALIZATION OF NTD IN HANARO IS FOCUSED. IN ADDITION TO THE UNIFORM IRRADIATION AND ACHIEVING THE TARGET RESISTIVITY WHICH ARE THE MOST IMPORTANT TECHNICAL REQUIREMENTS FOR THE NTD, OTHER ITEMS SUCH AS THE FUNCTION AND ROLE OF NTD, MARKET TREND, QUALITY CONTROL ARE INCLUDED. MEANWHILE THE ONLY ADVANTAGE OF NTD IS ACHIEVING VERY HIGH UNIFORMITY OF DOPING, IT HAS SEVERAL DISADVANTAGES DUE TO THE USE OF NUCLEAR REACTOR. THEREFORE THE SEMICONDUCTOR INDUSTRY HAS CONTINUED DEVELOPMENT OF TECHNOLOGY TO REPLACE NTD, AND THE DEMAND OF NTD HAD BEEN DECREASED A LOT DURING 1990S. AS THE DEMAND FOR LARGE CRYSTAL INCREASES, HOWEVER, THE NTD DEMAND BEGAN TO INCREASE AGAIN FROM 2000. SINCE THE DEMAND FOR THE LARGER CRYSTAL WILL BE CONTINUED IN THE FUTURE, THE ROLE OF NTD WOULD BE NEEDED FOR THE LONGER TIME. IN ORDER TO MITIGATE THIS TREND OF DEMAND, THE REACTOR SHOULD BE CAPABLE OF ACCEPTING LARGE CRYSTAL AND THE EFFORT TO IMPROVE DOPING UNIFORMITY AND TO REDUCE THE COST SHOULD CONTINUED.

Selection of chemical forms of iodine for transmutation of 129I

International Nuclear Information System (INIS)

Shirasu, Yoshiro; Minato, Kazuo

2003-01-01

To select suitable chemical forms of iodine for the target for transmutation of 129 I, the properties of iodine compounds of NaI, MgI 2 , CaI 2 , CuI and Ca(IO 3 ) 2 were compared and the out-of-reactor heating experiments of the pellets of CuI and Ca(IO 3 ) 2 with the cladding materials were carried out. CuI and Ca(IO 3 ) 2 are not deliquescent but stable in the air, which is of great advantage to construction, operation and maintenance of the processing plants. The cladding with Cu metal liner could be compatible with CuI though the compatibility of the stainless steel with CuI is not good. Ca(IO 3 ) 2 should be deleted from the list of the candidate target materials for the transmutation of 129 I due to the severe chemical reaction with the cladding materials

Hydrogen bond disruption in DNA base pairs from (14)C transmutation.

Science.gov (United States)

Sassi, Michel; Carter, Damien J; Uberuaga, Blas P; Stanek, Christopher R; Mancera, Ricardo L; Marks, Nigel A

2014-09-04

Recent ab initio molecular dynamics simulations have shown that radioactive carbon does not normally fragment DNA bases when it decays. Motivated by this finding, density functional theory and Bader analysis have been used to quantify the effect of C → N transmutation on hydrogen bonding in DNA base pairs. We find that (14)C decay has the potential to significantly alter hydrogen bonds in a variety of ways including direct proton shuttling (thymine and cytosine), thermally activated proton shuttling (guanine), and hydrogen bond breaking (cytosine). Transmutation substantially modifies both the absolute and relative strengths of the hydrogen bonding pattern, and in two instances (adenine and cytosine), the density at the critical point indicates development of mild covalent character. Since hydrogen bonding is an important component of Watson-Crick pairing, these (14)C-induced modifications, while infrequent, may trigger errors in DNA transcription and replication.

Simulating irradiation hardening in tungsten under fast neutron irradiation including Re production by transmutation

Science.gov (United States)

Huang, Chen-Hsi; Gilbert, Mark R.; Marian, Jaime

2018-02-01

Simulations of neutron damage under fusion energy conditions must capture the effects of transmutation, both in terms of accurate chemical inventory buildup as well as the physics of the interactions between transmutation elements and irradiation defect clusters. In this work, we integrate neutronics, primary damage calculations, molecular dynamics results, Re transmutation calculations, and stochastic cluster dynamics simulations to study neutron damage in single-crystal tungsten to mimic divertor materials. To gauge the accuracy and validity of the simulations, we first study the material response under experimental conditions at the JOYO fast reactor in Japan and the High Flux Isotope Reactor at Oak Ridge National Laboratory, for which measurements of cluster densities and hardening levels up to 2 dpa exist. We then provide calculations under expected DEMO fusion conditions. Several key mechanisms involving Re atoms and defect clusters are found to govern the accumulation of irradiation damage in each case. We use established correlations to translate damage accumulation into hardening increases and compare our results to the experimental measurements. We find hardening increases in excess of 5000 MPa in all cases, which casts doubts about the integrity of W-based materials under long-term fusion exposure.

Partitioning and transmutation. Annual report 2007

Energy Technology Data Exchange (ETDEWEB)

Aneheim, Emma; Ekberg, Christian; Englund, Sofie; Fermvik, Anna; Foreman, Mark St. J.; Liljenzin, Jan-Olov; Retegan, Teodora; Skarnemark, Gunnar; Wald, Karin (Nuclear Chemistry, Dept. of Chemical and Biological Engineering, Chalmers Univ. of Technology, Goeteborg (SE))

2007-01-15

The long-lived elements in the spent nuclear fuels are mostly actinides, some fission products (79Se, 87Rb, 99Tc, 107Pd, 126Sn, 129I, 135Cs) and activation products (14C, 36Cl, 59Ni, 93Zr, 94Nb). To be able to destroy the long-lived elements in a transmutation process they must be separated from the rest of the spent nuclear fuel. The most difficult separations to make are those between trivalent actinides and lanthanides, due to their relatively similar chemical properties, and those between different actinides themselves. These separations are necessary to obtain the desired efficiency of the transmutation process and in order not to create any unnecessary waste thus rendering the process useless. Solvent extraction is an efficient and well-known method that makes it possible to have separation factors that fulfil the highly set demands on purity of the separated phases and on small losses. Chalmers University of Technology is involved in research regarding the separation of actinides and lanthanides and between the actinides themselves as a partner in several European frame work programmes from NEWPART in the 4th framework via PARTNEW and EUROPART to ACSEPT now in the 7th programme. The aims of the projects have now shifted from basic understanding to more applied research with focus on process development. However, since a further investigation on basic understanding of the chemical behaviour is required, we have our main focus on the chemical processes and understanding of how they work. Due to new recruitments we will now also work on ligand design and development. This will decrease the response time between new ligands and their evaluation.

Nuclear data for accelerator-driven transmutation. Annual report 1998/99

Energy Technology Data Exchange (ETDEWEB)

Blomgren, J.; Johansson, C.; Klug, J.; Olsson, N.; Renberg, P.U. [Uppsala Univ. (Sweden). Dept. of Neutron Research. The Svedberg Lab.

1999-09-01

The present project, supported as a research task agreement by the Nuclear Power Inspectorate, the Nuclear Fuel and Waste Management Co, Barsebaeck Kraft AB and Vattenfall AB, started according to the plan 1998-07-01. From 1999-01-01 the project also receives support from the Defence Research Institute. The primary objective from the supporting organizations is to promote research and research education of relevance for development of the national competence within nuclear energy. The aim of the project is in short to: promote development of the competence within nuclear physics and nuclear technology by supporting PhD students; push forward the international research front regarding fundamental nuclear data within the presently highlighted research area 'accelerator-driven transmutation'; strengthen the Swedish influence within the mentioned research area by expanding the international contact network; and constitute a basis for Swedish participation in the nuclear data activities at IAEA and OECD/NEA. The project is run by the Department of Neutron Research at Uppsala University, and is utilizing the unique neutron beam facility at the national The Svedberg Laboratory (TSL) at Uppsala University. In this document, we give a status report after the first year (1998-07-01--1999-06-30) of the project.

Nuclear data for accelerator-driven transmutation. Annual report 2000 / 2001

International Nuclear Information System (INIS)

Blomgren, J.; Johansson, C.; Klug, J.; Olsson, N.; Pomp, S.; Renberg, P.U.

2001-09-01

The present project, supported as a research task agreement by SKI, SKB, Barsebaeck Kraft AB and Vattenfall AB, started 1998-07-01. From 1999-01-01 the project also receives support from the Defence Research Establishment. The primary objective from the supporting organizations is to promote research and research education of relevance for development of the national competence within nuclear energy. The aim of the project is in short to: promote development of the competence within nuclear physics and nuclear technology by supporting licentiate and PhD students, push forward the international research front regarding fundamental nuclear data within the presently highlighted research area 'accelerator-driven transmutation', strengthen the Swedish influence within the mentioned research area by expanding the international contact network, constitute a basis for Swedish participation in the nuclear data activities at IAEA and OECD/NEA. The project is run by the Department of Neutron Research at Uppsala University, and is utilizing the unique neutron beam facility at the national The Svedberg Laboratory. In this document, we give a status report after the third year (2000-07-01--2001-06-30) of the project. The annual report also includes a report with the title: Charge-exchange giant resonances as probes of nuclear structure. This report is indexed separately

Nuclear data for accelerator-driven transmutation. Annual report 1998/99

International Nuclear Information System (INIS)

Blomgren, J.; Johansson, C.; Klug, J.; Olsson, N.; Renberg, P.U.

1999-09-01

The present project, supported as a research task agreement by the Nuclear Power Inspectorate, the Nuclear Fuel and Waste Management Co, Barsebaeck Kraft AB and Vattenfall AB, started according to the plan 1998-07-01. From 1999-01-01 the project also receives support from the Defence Research Institute. The primary objective from the supporting organizations is to promote research and research education of relevance for development of the national competence within nuclear energy. The aim of the project is in short to: promote development of the competence within nuclear physics and nuclear technology by supporting PhD students; push forward the international research front regarding fundamental nuclear data within the presently highlighted research area 'accelerator-driven transmutation'; strengthen the Swedish influence within the mentioned research area by expanding the international contact network; and constitute a basis for Swedish participation in the nuclear data activities at IAEA and OECD/NEA. The project is run by the Department of Neutron Research at Uppsala University, and is utilizing the unique neutron beam facility at the national The Svedberg Laboratory (TSL) at Uppsala University. In this document, we give a status report after the first year (1998-07-01--1999-06-30) of the project

New data libraries for transmutation studies

Energy Technology Data Exchange (ETDEWEB)

Kloosterman, J.L. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Hoogenboom, J.E. [Interfaculty Reactor Inst., Delft (Netherlands)

1995-06-01

The fuel depletion code ORIGEN-S is often used for transmutation studies. It uses three different working libraries for actinides, fission products, and light elements, which contain decay data, cross-section data and fission product yields. These data have been renewed with data based on the JEF2.2 and the EAF3 evaluated files. Furthermore, data for 201 fission products have been added to the libraries. The new data libraries are particular suitable for parameter studies and other introductory calculations. For more accurate calculations, it is advised to regularly update the cross sections of the most important actinides and fission products during the burnup sequence. (orig.).

New data libraries for transmutation studies

Energy Technology Data Exchange (ETDEWEB)

Kloosterman, J.L. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Hoogenboom, J.E. [Interfaculty Reactor Inst., Delft (Netherlands)

1995-12-31

The fuel depletion code ORIGEN-S is often used for transmutations studies. It uses three different working libraries for actinides, fission products, and light elements, which contain decay data, cross-section data and fission product yields. These data have renewed with data based on the JEF2.2 and the EAF3 evaluated files. Furthermore, data for 201 fission products have been added to the libraries. The new data libraries are particular suitable for parameter studies and other introductory calculations. For more accurate calculations, it is advised to regularly update the cross sections of the most important actinides and fission products during the burnup sequence. (author) 9 refs.

Transmutation of singularities in optical instruments

Energy Technology Data Exchange (ETDEWEB)

Tyc, Tomas [Institute of Theoretical Physics and Astrophysics, Masaryk University, Kotlarska 2, 61137 Brno (Czech Republic); Leonhardt, Ulf [School of Physics and Astronomy, University of St Andrews, North Haugh, St Andrews KY16 9SS (United Kingdom)], E-mail: tomtyc@physics.muni.cz

2008-11-15

We propose a method for eliminating a class of singularities in optical media where the refractive index goes to zero or infinity at one or more isolated points. Employing transformation optics, we find a refractive index distribution equivalent to the original one that is nonsingular but shows a slight anisotropy. In this way, the original singularity is 'transmuted' into another, weaker type of singularity where the permittivity and permeability tensors are discontinuous at one point. The method is likely to find applications in designing and improving optical devices by making them easier to implement or to operate in a broad band of the spectrum.

Overview of the French program in chemical separations and transmutation

International Nuclear Information System (INIS)

Baudin, G.

1993-01-01

A long-range effort has begun in France that is aimed at the reduction of the volume and activity level of wastes containing long half-life radionuclides. This effort constitutes the SPIN (SeParations-INcineration) Program which investigates separations techniques that can improve current reprocessing technologies coupled with destruction of long-lived species through transmutation. Removal and destruction of specific radionuclides (e.g., neptunium, americium, technetium, iodine, cesium, and strontium) will be emphasized. Advanced solvent extraction chemistry focusing, for example, on development and implementation of diamides for actinide-lanthanide separations constitutes an important component of the SPIN program. The second component of the program focuses on inventory reductions through transmutation of such long-lived nuclides in fast reactor systems (Super Phenix). Accelerator-based systems are also being evaluated as a possible long-term option. Both of these components of the SPIN program are aimed at further reduction of the potential radiotoxicity and radiological impact of high-level wastes destined for geological storage. In this presentation, major activities of the SPIN Program will be described with emphasis on activities related to advanced chemical separations

Laser enhanced radioactive decay and selective transmutation of nuclear waste

International Nuclear Information System (INIS)

Saloman, R.; Aarnio, P.; Ala-Heikkila, J.; Hakola, A.; Santala, M.

2007-01-01

We have investigated narrow-band coherent laser radiation - ranging from visible to X- and to gamma-ray wave length region - and their interactions both directly with photon-nuclear couplings and indirectly through the photon-electron and electron-nucleus interactions. In particular we discuss various means of selective excitation of nuclear resonance states by narrowband lasers. During the relaxation process the active nucleus may return to its initial ground-state or find another final state. In the latter case the nucleus is transmuted into a state which may have beneficial properties for instance concerning radioactivity. One ideal case would be the destruction of long-lived nuclear waste isotopes into faster decaying ones. The essential presumption is that the excitation process is selective and efficient as regards background processes due to unwanted excitation channels of the primary isotope and due to other surrounding nuclides. The paper consists of 1) a short review of generating short-wave length coherent light sources, 2) a survey of potential photon-induced nuclear states and their decay channels, and 3) a determination of the selectivity of the transmutation process

Detecting neutrons by forward recoil protons at the Energy & Transmutation facility: Detector development and calibration with 14.1-MeV neutrons

Science.gov (United States)

Afanasev, S.; Vishnevskiy, A.; Vishnevskiy, D.; Rogachev, A.; Tyutyunnikov, S.

2017-05-01

As part of the Energy & Transmutation project, we are developing a detector for neutrons with energies in the 10-100 MeV range emitted from the target irradiated by a charged-particle beam. The neutron is detected by measuring the time-of-flight and total kinetic energy of the forward-going recoil proton [1] knocked out at a small angle from a thin layer of plastic scintillator, which has to be selected against an intense background created by γ quanta, scattered neutrons, and charged particles. On the other hand, neutron energy has to be measured over the full range with no extra tuning of the detector operation regime. Initial measurements with a source of 14.1-MeV neutrons are reported.

Sodium-cooled fast reactor core designs for transmutation of MHR spent fuel

International Nuclear Information System (INIS)

Hong, S. G.; Kim, Y. H.; Venneri, F.

2010-01-01

In this paper, the core design analyses of sodium cooled fast reactors (SFR) are performed for the effective transmutation of the DB (Deep Burn)-MHR (Modular Helium Reactor). In this concept, the spent fuels of DB-MHR are transmuted in SFRs with a closed fuel cycle after TRUs from LWR are first incinerated in a DB-MHR. We introduced two different type SFR core designs for this purpose, and evaluated their core performance parameters including the safety-related parameters. In particular, the cores are designed to have lower transmutation rate relatively to our previous work so as to make the fuel characteristics more feasible. The first type cores which consist of two enrichment regions are typical homogeneous annular cores and they rate 900 MWt power. On the other hand, the second type cores which consist of a central non-fuel region and a single enrichment fuel region rate relatively higher power of 1500 MWt. For these cores, the moderator rods (YH 1.8 ) are used to achieve less positive sodium void worth and the more negative Doppler coefficient because the loading of DB-MHR spent fuel leads to the degradation of these safety parameters. The analysis results show that these cores have low sodium void worth and negative reactivity coefficients except for the one related with the coolant expansion but the coolant expansion reactivity coefficient is within the typical range of the typical SFR cores. (authors)

Transmutation in ADS and needs for nuclear data, with an introduction to the n-TOF at CERN

CERN Document Server

González, E; Fernández, R; García, J; Villamarín, D

1999-01-01

Transmutation can help in the nuclear waste problem by reducing seriously the life and amount of the most dangerous isotopes (radiotoxicity, heat, packing volume and neutron multiplication reductions). ADS are one of the best technologies for nuclear waste transmutation at large scale. Although enough information is available to prepare conceptual designs and make assessments on their performance, a large R&D campaign is required to obtain the precision data required to optimize the detailed engineering design and refine our expectations calculations on waste reduction by the different transmutation strategies being proposed. In particular a large R&D effort is required in nuclear physics, where fundamental differential measurements and integral verification experiments are required. In this sense, the PS213 n-TOF at CERN PS (at Switzerland) will become one of the largest installations to perform the fundamental differential measurements and a wide international collaboration has been setup to perform...

Design Concept of Kijang Research Reactor for Neutron Transmutation Doping of 300 MM ingots

International Nuclear Information System (INIS)