Preliminary studies on trace element contamination in dumping sites of municipal wastes in India and Vietnam

Science.gov (United States)

Agusa, T.; Kunito, T.; Nakashima, E.; Minh, T. B.; Tanabe, S.; Subramanian, A.; Viet, P. H.

2003-05-01

The disposal of wastes in dumping sites has increasingly caused concem about adverse health effects on the populations living nearby. However, no investigation has been conducted yet on contamination in dumping sites of municipal wastes in Asian developing countries. In this study, concentrations of 11 trace elements (V, Cr, Mn, Co, Cu, Zn, Mo, Ag, Cd, Sb and Pb) were detennined in scalp hair from the population living nearby and in soil from dumping sites and control sites of India and Vietnam. Soil samples in dumping site in India showed significantly higher concentrations of some trace elements than soils in control site, whereas this trend was not notable in Vietnam. This is probably due to the fact that the wastes were covered with the soil in the dumping site of Vietnam. Cadmium concentrations in some hair samples of people living near dumping site in India and Vietnam exceeded the level associated with learning disorder in children. Levels of most of the trace elements in hair were significantly higher in dumping site than those in control site in India and Vietnam, suggesting direct or indirect exposure to those elements from dumping wastes. To our knowledge, this is the first study of trace element contamination in dumping sites in India and Vietnam.

Root Cause Assessment of Pressure Drop Rise of a Packed Bed of Lithium Hydroxide in the International Space Station Trace Contaminant Control System

Science.gov (United States)

Aguilera, Tatiana; Perry, Jay L.

2009-01-01

The trace contaminant control system (TCCS) located in the International Space Station s (ISS) U.S. laboratory module employs physical adsorption, thermal catalytic oxidation, and chemical adsorption to remove trace chemical contamination produced by equipment offgassing and anthropogenic sources from the cabin atmosphere. The chemical adsorption stage, consisting of a packed bed of granular lithium hydroxide (LiOH), is located after the thermal catalytic oxidation stage and is designed to remove acid gas byproducts that may be formed in the upstream oxidation stage. While in service on board the ISS, the LiOH bed exhibited a change in flow resistance that leading to flow control difficulties in the TCCS. Post flight evaluation revealed LiOH granule size attrition among other changes. An experimental program was employed to investigate mechanisms hypothesized to contribute to the change in the packed bed s flow resistance. Background on the problem is summarized, including a discussion of likely mechanisms. The experimental program is described, results are presented, and implications for the future are discussed.

Trace metal contamination of Beaufort's Dyke, North Channel, Irish Sea: A legacy of ordnance disposal

International Nuclear Information System (INIS)

Callaway, Alexander; Quinn, Rory; Brown, Craig J.; Service, Matthew; Benetti, Sara

2011-01-01

Highlights: → Our samples are the first trace metal concentrations taken from the valley of Beaufort's Dyke. → There is no clear trend between concentrations of trace metals in Dyke and NMMP sediments. → Particle transport simulations show dispersal of trace metals from Beaufort's Dyke is possible. → Disposed ordnance may also contribute to contamination of surrounding areas. → These methods could help predict areas at risk of future trace metal contamination as a result of ordnance disposal. - Abstract: Beaufort's Dyke is a disused ordnance disposal ground within the North Channel of the Irish Sea. Over 1 million tonnes of ordnance were disposed of in the dyke over a 40 year period representing a substantial volume of trace metal pollutants introduced to the seabed. Utilising particle transport modelling software we simulated the potential transport of metal particles from Beaufort's Dyke over a 3 month period. This demonstrated that Beaufort's Dyke has the potential to act as a source for trace metal contamination to areas beyond the submarine valley. Trace metal analysis of sediments from the Dyke and surrounding National Marine Monitoring Programme areas demonstrate that the Dyke is not the most contaminated site in the region. Particle transport modelling enables the transport pathways of trace metal contaminants to be predicted. Implementation of the technique in other munitions disposal grounds will provide valuable information for the selection of monitoring stations.

Trace Contaminant Monitor for Air in Spacecraft, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — A need exists for analyzers that can measure trace contaminants in air on board spacecraft. Toxic gas buildup can endanger the crew particularly during long...

NSF-RANN Trace Contaminants Program directory. [Personnel directory

Energy Technology Data Exchange (ETDEWEB)

Purnell, P.A.; Smith, S.K.; Wilkes, C.F.

1976-10-01

This directory is designed to aid effective communication throughout the National Science Foundation's Trace Contaminants Program, Research Applied to National Needs. The majority of the participants in the Program are represented by name, address, telephone number, and a very brief description of research interest. The directory has five major divisions to facilitate its use. Section I contains a listing of the program managers associated with the NSF-RANN Trace Contaminants Program. Section II lists the principal investigators, co-principal investigators, and coordinators of each of the research grants in the Program. Section III lists the personnel by individual projects. Section IV contains a total alphabetic listing complete with project titles and Section V contains a keyword index. This directory is maintained by the Toxic Materials Information Center as part of the Environmental Resource Center of the Information Center Complex, Information Division, Oak Ridge National Laboratory.

Measurements of trace contaminants in closed-type plant cultivation chambers

Science.gov (United States)

Tani, A.; Kiyota, M.; Aiga, I.; Nitta, K.; Tako, Y.; Ashida, A.; Otsubo, K.; Saito, T.

Trace contaminants generated in closed facilities can cause abnormal plant growth. We present measurement data of trace contaminants released from soils, plants, and construction materials. We mainly used two closed chambers, a Closed-type Plant and Mushroom Cultivation Chamber (PMCC) and Closed-type Plant Cultivation Equipment (CPCE). Although trace gas budgets from soils obtained in this experiment are only one example, the results indicate that the budgets of trace gases, as well as CO_2 and O_2, change greatly with the degree of soil maturation and are dependent on the kind of substances in the soil. Both in the PMCC and in the CPCE, trace gases such as dioctyl phthalate (DOP), dibutyl phthalate (DBP), toluene and xylene were detected. These gases seemed to be released from various materials used in the construction of these chambers. The degree of increase in these trace gas levels was dependent on the relationship between chamber capacity and plant quantity. Results of trace gas measurement in the PMCC, in which lettuce and shiitake mushroom were cultivated, showed that ethylene was released both from lettuce and from the mushroom culture bed. The release rates were about 90 ng bed^-1 h^-1 for the shiitake mushroom culture bed (volume is 1700 cm^3) and 4.1 ~ 17.3 ng dm^-2h^-1 (leaf area basis) for lettuce. Higher ethylene release rates per plant and per unit leaf area were observed in mature plants than in young plants.

Analytical analysis of soil-moisture and trace-contaminant transport

International Nuclear Information System (INIS)

Larson, N.M.; Reeves, M.

1976-03-01

A transport model is presented which predicts the coupled movement of both water and trace contaminants through a layered and unsaturated soil-moisture zone. In order to achieve computation speeds suitable for watershed implementations, moisture properties are approximated as exponential functions of pressure head, and lateral flows are treated as sinks in a basically vertical one-dimensional analysis. In addition, only advection by the Darcy-flow velocities and linear adsorption by the soil matrix are considered in depicting movement of the trace contaminant. Formal solution of the resulting transport equations is obtained through use of both eigenfunction-expansion and coordinate-transformation methods. Numerical solution is effected by means of a program written in FORTRAN IV and implemented on an IBM 360/91 computer. Two example calculations illustrate both strengths and weaknesses of our model

Reconstructing Early Industrial Contributions to Legacy Trace Metal Contamination in Southwestern Pennsylvania

Science.gov (United States)

Rossi, R.; Bain, D.; Hillman, A. L.; Pompeani, D. P.; Abbott, M. B.

2015-12-01

The remobilization of legacy contamination stored in floodplain sediments remains a threat to ecosystem and human health, particularly with potential changes in global precipitation patterns and flooding regimes. Vehicular and industrial emissions are often the dominant, recognized source of anthropogenic trace metal loadings to ecosystems today. However, loadings from early industrial activities are poorly characterized and potential sources of trace metal inputs. While potential trace metal contamination from these activities is recognized (e.g., the historical use of lead arsenate as a pesticide), the magnitude and distribution of legacy contamination is often unknown. This presentation reconstructs a lake sediment record of trace metal inputs from an oxbow lake in Southwestern Pennsylvania. Sediment cores were analyzed for major and trace metal chemistry, carbon to nitrogen ratios, bulk density, and magnetic susceptibility. Sediment trace metal chemistry in this approximately 250 year record (180 cm) record changes in land use and industry both in the 19th century and the 20th century. Of particular interest is early 19th century loadings of arsenic and calcium to the lake, likely attributable to pesticides and lime used in tanning processes near the lake. After this period of tanning dominated inputs, sediment barium concentrations rise, likely reflecting the onset of coal mining operations and resulting discharge of acid mine drainage to surface waters. In the 20th century portion of our record (70 -20 cm), patterns in sediment zinc, cadmium, and lead concentrations are dominated by the opening and closing of the nearby Donora Zinc Works and the American Steel & Wire Works, infamous facilities in the history of air quality regulation. The most recent sediment chemistry records periods include the enactment of air pollution legislation (~ 35 cm), and the phase out of tetraethyl leaded gasoline (~30 cm). Our study documents the impact of early industry in the

1993 Proceedings volume 1--Contamination control; symposium on minienvironments; symposium on biocontamination control

International Nuclear Information System (INIS)

Anon.

1993-01-01

Volume 1 contains the proceedings from three symposia. Contamination Control includes the following topics: Atmospheric pressure ionization mass spectroscopy (APIMS) applications; APIMS development; contamination control in cleanroom air; defect reduction in semiconductor processes; contamination control in the aerospace industry; filtration of gases; ultrapure chemical and DI water; filtration of chemicals; wafer cleaning/trace contaminant effects; wafer cleaning techniques; detection of particles in UHP fluids; detection of surface particles; modeling contamination; detection of surface organics; modeling, particle transport, deposition, and removal; and detection of surface metallics. Symposium on Minienvironments includes the following: design of minienvironments; robotics and I/O transport; testing, methods, and standards. The Symposium on Biocontamination Control includes the following: microbial CC facility requirements in pharmaceutical, biological, and medical device manufacture; cleaning and disinfecting methods and devices for bio CC; biocontamination control devices, methodology, and standards, airborne and surface microbial monitoring methods and devices; and regulatory issues in bio CC--present and future. All papers within the scope of the Energy Data Base have been processed separately for inclusion on the data base

Contaminant transport, revegetation, and trace element studies at inactive uranium mill tailings piles

International Nuclear Information System (INIS)

Dreesen, D.R.; Marple, M.L.; Kelley, N.E.

1978-01-01

The stabilization of inactive uranium mill tailings piles is presently under study. These studies have included investigations of stabilizing tailings by attempting to establish native vegetation without applying irrigation. Examination of processes which transport tailings or associated contaminants into the environment has been undertaken to better understand the containment provided by various stabilization methods. The uptake of toxic trace elements and radionuclides by vegetation has been examined as a mechanism of contaminant transport. The source terms of 222 Rn from inactive piles have been determined as well as the attenuation of radon flux provided by shallow soil covers. The possibility of shallow ground water contamination around an inactive pile has been examined to determine the significance of ground water transport as a mode of contaminant migration. The rationale in support of trace element studies related to uranium milling activities is presented including the enrichment, migration, and toxicities of trace elements often associated with uranium deposits. Some concepts for the stabilization of inactive piles are presented to extrapolate from research findings to practical applications. 25 references, 8 tables

Effects of incubation on solubility and mobility of trace metals in two contaminated soils

International Nuclear Information System (INIS)

Ma, Lena Q.; Dong Yan

2004-01-01

Much research has focused on changes in solubility and mobility of trace metals in soils under incubation. In this experiment, changes in solubility and mobility of trace metals (Pb, Cu and As) and Fe in two contaminated soils from Tampa, Florida and Montreal, Canada were examined. Soils of 30 g were packed in columns and were incubated for 3-80 days under water-flooding incubation. Following incubation, metal concentrations in pore water (water soluble) and in 0.01 M CaCl 2 leachates (exchangeable+water soluble) were determined. While both soils were contaminated with Pb (1600-2500 mg kg -1 ), Tampa soil was also contaminated with As (230 mg kg -1 ). Contrast to the low pH (3.8) of Tampa soil, Montreal soil had an alkaline pH of 7.7 and high Ca of 1.6%. Concentrations of Fe(II) increased with incubation time in the Tampa soil mainly due to reductive Fe dissolution, but decreased in the Montreal soil possibly due to formation of FeCO 3 . The inverse relationship between concentrations of Pb and Fe(II) in pore water coupled with the fact that Fe(II) concentrations were much greater than those of Pb in pore water may suggest the importance of Fe(II) in controlling Pb solubility in soils. However, changes in concentrations of Fe(II), Pb, Cu and As in pore water with incubation time were similar to those in leachate, i.e. water soluble metals were positively related to exchangeable metals in the two contaminated soils. This research suggests the importance of Fe in controlling metal solubility and mobility in soils under water-flooded incubation. - Iron is important in controlling metal solubility and mobility in flooded soils

Contamination and Health Risks from Heavy Metals (Cd and Pb and Trace Elements (Cu and Zn in Dairy Products

Directory of Open Access Journals (Sweden)

Hamid Reza Ghafari

2017-08-01

Conclusion: Considering the serious contamination of some brands of butter and cheese by Cu and Pb, a control of heavy metals and trace elements levels during the whole production processing of dairy products must be applied.

Comparison of trace element contamination levels (Cu, Zn, Fe, Cd ...

African Journals Online (AJOL)

Comparison of trace element contamination levels (Cu, Zn, Fe, Cd and Pb) in the soft tissues of the gastropods Tympanotonus fuscatus fuscatus and Tf radula collected in the Ebrié Lagoon (Côte d'Ivoire): Evidence of the risks linked to linked to lead and.

Trace elements contamination of soils around gold mine tailings ...

African Journals Online (AJOL)

This study investigated the issue of tailings dams as a potential source of trace elements contamination in soils at the Obuasi gold mine in Ghana. Soil samples taken from depths of up to 12 cm and within a radius of 400 m from the tailings dams (active and recommissioned), were analysed for As, Cu, Pb and. Zn using ...

Trace element contamination in feather and tissue samples from Anna’s hummingbirds

Science.gov (United States)

Mikoni, Nicole A.; Poppenga, Robert H.; Ackerman, Joshua T.; Foley, Janet E.; Hazlehurst, Jenny; Purdin, Güthrum; Aston, Linda; Hargrave, Sabine; Jelks, Karen; Tell, Lisa A.

2017-01-01

Trace element contamination (17 elements; Be, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Mo, Cd, Ba, Hg, Tl, and Pb) of live (feather samples only) and deceased (feather and tissue samples) Anna's hummingbirds (Calypte anna) was evaluated. Samples were analyzed using inductively coupled plasma-mass spectrometry (ICP-MS; 17 elements) and atomic absorption spectrophotometry (Hg only). Mean plus one standard deviation (SD) was considered the benchmark, and concentrations above the mean + 1 SD were considered elevated above normal. Contour feathers were sampled from live birds of varying age, sex, and California locations. In order to reduce thermal impacts, minimal feathers were taken from live birds, therefore a novel method was developed for preparation of low mass feather samples for ICP-MS analysis. The study found that the novel feather preparation method enabled small mass feather samples to be analyzed for trace elements using ICP-MS. For feather samples from live birds, all trace elements, with the exception of beryllium, had concentrations above the mean + 1 SD. Important risk factors for elevated trace element concentrations in feathers of live birds were age for iron, zinc, and arsenic, and location for iron, manganese, zinc, and selenium. For samples from deceased birds, ICP-MS results from body and tail feathers were correlated for Fe, Zn, and Pb, and feather concentrations were correlated with renal (Fe, Zn, Pb) or hepatic (Hg) tissue concentrations. Results for AA spectrophotometry analyzed samples from deceased birds further supported the ICP-MS findings where a strong correlation between mercury concentrations in feather and tissue (pectoral muscle) samples was found. These study results support that sampling feathers from live free-ranging hummingbirds might be a useful, non-lethal sampling method for evaluating trace element exposure and provides a sampling alternative since their small body size limits traditional sampling of blood and tissues. The

Source Evaluation and Trace Metal Contamination in Benthic Sediments from Equatorial Ecosystems Using Multivariate Statistical Techniques.

Directory of Open Access Journals (Sweden)

Nsikak U Benson

Full Text Available Trace metals (Cd, Cr, Cu, Ni and Pb concentrations in benthic sediments were analyzed through multi-step fractionation scheme to assess the levels and sources of contamination in estuarine, riverine and freshwater ecosystems in Niger Delta (Nigeria. The degree of contamination was assessed using the individual contamination factors (ICF and global contamination factor (GCF. Multivariate statistical approaches including principal component analysis (PCA, cluster analysis and correlation test were employed to evaluate the interrelationships and associated sources of contamination. The spatial distribution of metal concentrations followed the pattern Pb>Cu>Cr>Cd>Ni. Ecological risk index by ICF showed significant potential mobility and bioavailability for Cu, Cu and Ni. The ICF contamination trend in the benthic sediments at all studied sites was Cu>Cr>Ni>Cd>Pb. The principal component and agglomerative clustering analyses indicate that trace metals contamination in the ecosystems was influenced by multiple pollution sources.

A Nanoparticulate Photocatalytic Filter for Removal of Trace Contaminant Gases, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Maintaining a healthy atmosphere in closed life support systems is necessary for the well being of the crew and success of a space mission. Current trace contaminant...

Phytostabilization of semiarid soils residually contaminated with trace elements using by-products: Sustainability and risks

Energy Technology Data Exchange (ETDEWEB)

Perez-de-Mora, Alfredo, E-mail: perezdemora@gmail.com [Instituto de Recursos Naturales y Agrobiologia de Sevilla (IRNAS), CSIC, PO Box 1052, 41080 Sevilla (Spain); Madejon, Paula; Burgos, Pilar; Cabrera, Francisco [Instituto de Recursos Naturales y Agrobiologia de Sevilla (IRNAS), CSIC, PO Box 1052, 41080 Sevilla (Spain); Lepp, Nicholas W. [35, Victoria Road, Formby, Liverpool L37 7DH (United Kingdom); Madejon, Engracia [Instituto de Recursos Naturales y Agrobiologia de Sevilla (IRNAS), CSIC, PO Box 1052, 41080 Sevilla (Spain)

2011-10-15

We investigated the efficiency of various by-products (sugarbeet lime, biosolid compost and leonardite), based on single or repeated applications to field plots, on the establishment of a vegetation cover compatible with a stabilization strategy on a multi-element (As, Cd, Cu, Pb and Zn) contaminated soil 4-6 years after initial amendment applications. Results indicate that the need for re-treatment is amendment- and element-dependent; in some cases, a single application may reduce trace element concentrations in above-ground biomass and enhance the establishment of a healthy vegetation cover. Amendment performance as evaluated by % cover, biomass and number of colonizing taxa differs; however, changes in plant community composition are not necessarily amendment-specific. Although the translocation of trace elements to the plant biotic compartment is greater in re-vegetated areas, overall loss of trace elements due to soil erosion and plant uptake is usually smaller compared to that in bare soil. - Highlights: > By-products enhance vegetation dynamics in contaminated semiarid soils. > Depending on the situation single or repeated incorporations may be required. > The structure of the plant community established is not amendment-dependent. > Phytostabilization reduces overall loss of trace elements in semiarid soils. - Phytostabilization using by-products as amendments is a suitable approach for long-term immobilization of various trace elements in semiarid contaminated soils.

Phytostabilization of semiarid soils residually contaminated with trace elements using by-products: Sustainability and risks

International Nuclear Information System (INIS)

Perez-de-Mora, Alfredo; Madejon, Paula; Burgos, Pilar; Cabrera, Francisco; Lepp, Nicholas W.; Madejon, Engracia

2011-01-01

We investigated the efficiency of various by-products (sugarbeet lime, biosolid compost and leonardite), based on single or repeated applications to field plots, on the establishment of a vegetation cover compatible with a stabilization strategy on a multi-element (As, Cd, Cu, Pb and Zn) contaminated soil 4-6 years after initial amendment applications. Results indicate that the need for re-treatment is amendment- and element-dependent; in some cases, a single application may reduce trace element concentrations in above-ground biomass and enhance the establishment of a healthy vegetation cover. Amendment performance as evaluated by % cover, biomass and number of colonizing taxa differs; however, changes in plant community composition are not necessarily amendment-specific. Although the translocation of trace elements to the plant biotic compartment is greater in re-vegetated areas, overall loss of trace elements due to soil erosion and plant uptake is usually smaller compared to that in bare soil. - Highlights: → By-products enhance vegetation dynamics in contaminated semiarid soils. → Depending on the situation single or repeated incorporations may be required. → The structure of the plant community established is not amendment-dependent. → Phytostabilization reduces overall loss of trace elements in semiarid soils. - Phytostabilization using by-products as amendments is a suitable approach for long-term immobilization of various trace elements in semiarid contaminated soils.

Removal of trace metal contaminants from potable water by electrocoagulation

Science.gov (United States)

Heffron, Joe; Marhefke, Matt; Mayer, Brooke K.

2016-06-01

This study investigated the effects of four operational and environmental variables on the removal of trace metal contaminants from drinking water by electrocoagulation (EC). Removal efficiencies for five metals (arsenic, cadmium, chromium, lead and nickel) were compared under varying combinations of electrode material, post-treatment, water composition and pH. Iron electrodes out-performed aluminum electrodes in removing chromium and arsenic. At pH 6.5, aluminum electrodes were slightly more effective at removing nickel and cadmium, while at pH 8.5, iron electrodes were more effective for these metals. Regardless of electrode, cadmium and nickel removal efficiencies were higher at pH 8.5 than at pH 6.5. Post-EC treatment using membrane filtration (0.45 μm) enhanced contaminant removal for all metals but nickel. With the exception of lead, all metals exhibited poorer removal efficiencies as the ionic strength of the background electrolyte increased, particularly in the very high-solids synthetic groundwaters. Residual aluminum concentrations were lowest at pH 6.5, while iron residuals were lowest in low ionic strength waters. Both aluminum and iron residuals required post-treatment filtration to meet drinking water standards. EC with post-treatment filtration appears to effectively remove trace metal contaminants to potable water standards, but both reactor and source water parameters critically impact removal efficiency.

Mapping human health risks from exposure to trace metal contamination of drinking water sources in Pakistan

International Nuclear Information System (INIS)

Bhowmik, Avit Kumar; Alamdar, Ambreen; Katsoyiannis, Ioannis; Shen, Heqing; Ali, Nadeem; Ali, Syeda Maria; Bokhari, Habib; Schäfer, Ralf B.; Eqani, Syed Ali Musstjab Akber Shah

2015-01-01

The consumption of contaminated drinking water is one of the major causes of mortality and many severe diseases in developing countries. The principal drinking water sources in Pakistan, i.e. ground and surface water, are subject to geogenic and anthropogenic trace metal contamination. However, water quality monitoring activities have been limited to a few administrative areas and a nationwide human health risk assessment from trace metal exposure is lacking. Using geographically weighted regression (GWR) and eight relevant spatial predictors, we calculated nationwide human health risk maps by predicting the concentration of 10 trace metals in the drinking water sources of Pakistan and comparing them to guideline values. GWR incorporated local variations of trace metal concentrations into prediction models and hence mitigated effects of large distances between sampled districts due to data scarcity. Predicted concentrations mostly exhibited high accuracy and low uncertainty, and were in good agreement with observed concentrations. Concentrations for Central Pakistan were predicted with higher accuracy than for the North and South. A maximum 150–200 fold exceedance of guideline values was observed for predicted cadmium concentrations in ground water and arsenic concentrations in surface water. In more than 53% (4 and 100% for the lower and upper boundaries of 95% confidence interval (CI)) of the total area of Pakistan, the drinking water was predicted to be at risk of contamination from arsenic, chromium, iron, nickel and lead. The area with elevated risks is inhabited by more than 74 million (8 and 172 million for the lower and upper boundaries of 95% CI) people. Although these predictions require further validation by field monitoring, the results can inform disease mitigation and water resources management regarding potential hot spots. - Highlights: • Predictions of trace metal concentration use geographically weighted regression • Human health risk

Mapping human health risks from exposure to trace metal contamination of drinking water sources in Pakistan

Energy Technology Data Exchange (ETDEWEB)

Bhowmik, Avit Kumar [Institute for Environmental Sciences, University of Koblenz-Landau, Fortstrasse 7, D-76829 Landau in der Pfalz (Germany); Alamdar, Ambreen [Key Lab of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Katsoyiannis, Ioannis [Aristotle University of Thessaloniki, Department of Chemistry, Division of Chemical Technology, Box 116, Thessaloniki 54124 (Greece); Shen, Heqing [Key Lab of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Ali, Nadeem [Department of Environmental Sciences, FBAS, International Islamic University, Islamabad (Pakistan); Ali, Syeda Maria [Center of Excellence in Environmental Studies, King Abdulaziz University, Jeddah (Saudi Arabia); Bokhari, Habib [Public Health and Environment Division, Department of Biosciences, COMSATS Institute of Information Technology, Islamabad (Pakistan); Schäfer, Ralf B. [Institute for Environmental Sciences, University of Koblenz-Landau, Fortstrasse 7, D-76829 Landau in der Pfalz (Germany); Eqani, Syed Ali Musstjab Akber Shah, E-mail: ali_ebl2@yahoo.com [Key Lab of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Public Health and Environment Division, Department of Biosciences, COMSATS Institute of Information Technology, Islamabad (Pakistan)

2015-12-15

The consumption of contaminated drinking water is one of the major causes of mortality and many severe diseases in developing countries. The principal drinking water sources in Pakistan, i.e. ground and surface water, are subject to geogenic and anthropogenic trace metal contamination. However, water quality monitoring activities have been limited to a few administrative areas and a nationwide human health risk assessment from trace metal exposure is lacking. Using geographically weighted regression (GWR) and eight relevant spatial predictors, we calculated nationwide human health risk maps by predicting the concentration of 10 trace metals in the drinking water sources of Pakistan and comparing them to guideline values. GWR incorporated local variations of trace metal concentrations into prediction models and hence mitigated effects of large distances between sampled districts due to data scarcity. Predicted concentrations mostly exhibited high accuracy and low uncertainty, and were in good agreement with observed concentrations. Concentrations for Central Pakistan were predicted with higher accuracy than for the North and South. A maximum 150–200 fold exceedance of guideline values was observed for predicted cadmium concentrations in ground water and arsenic concentrations in surface water. In more than 53% (4 and 100% for the lower and upper boundaries of 95% confidence interval (CI)) of the total area of Pakistan, the drinking water was predicted to be at risk of contamination from arsenic, chromium, iron, nickel and lead. The area with elevated risks is inhabited by more than 74 million (8 and 172 million for the lower and upper boundaries of 95% CI) people. Although these predictions require further validation by field monitoring, the results can inform disease mitigation and water resources management regarding potential hot spots. - Highlights: • Predictions of trace metal concentration use geographically weighted regression • Human health risk

Soil amendments reduce trace element solubility in a contaminated soil and allow regrowth of natural vegetation

International Nuclear Information System (INIS)

Madejon, Engracia; Perez de Mora, Alfredo; Felipe, Efrain; Burgos, Pilar; Cabrera, Francisco

2006-01-01

We tested the effects of three amendments (a biosolid compost, a sugar beet lime, and a combination of leonardite plus sugar beet lime) on trace element stabilisation and spontaneous revegetation of a trace element contaminated soil. Soil properties were analysed before and after amendment application. Spontaneous vegetation growing on the experimental plot was studied by three surveys in terms of number of taxa colonising, percentage vegetation cover and plant biomass. Macronutrients and trace element concentrations of the five most frequent species were analysed. The results showed a positive effect of the amendments both on soil chemical properties and vegetation. All amendments increased soil pH and TOC content and reduced CaCl 2 -soluble-trace element concentrations. Colonisation by wild plants was enhanced in all amended treatments. The nutritional status of the five species studied was improved in some cases, while a general reduction in trace element concentrations of the aboveground parts was observed in all treated plots. The results obtained show that natural assisted remediation has potential for success on a field scale reducing trace element entry in the food chain. - Soil amendments affect soil chemistry and allow revegetation of soils contaminated by trace elements

Radioisotope studies of some effects and interactions of trace contaminants

International Nuclear Information System (INIS)

1976-01-01

The coordinated programme of ''isotopic tracer-aided studies of the biological side-effects of foreign chemical residues in food and agriculture'', initiated in 1973, had involved the participation of 12 scientists from 10 countries. Pesticide residues, toxic metals, atmospheric sulphur dioxide were studied, and the use of radiotracer techniques as monitoring tools for existing contaminant levels or for their biological effects. The programme had been successful in the development and application of selected labelled substrate techniques. Specific aspects studied were the effects of environmental contaminants at the molecular level of the cell nucleus, the development and significance of radioimmunoassay procedure for trace contaminants, action and joint action of toxic elements, and the radiometric analysis of cholinesterase as an index of exposure to organophosphorus and carbamate pesticides. Ten papers were presented and 12 coordinated investigations discussed. A number of recommendations were made

Evaluation of trace organic contaminants in ultra-pure water production processes by measuring total organic halogen formation potential

International Nuclear Information System (INIS)

Urano, Kohei; Iwase, Yoko

1984-01-01

A new procedure for the determination of organic substances in water with high accuracy and high sensitivity was proposed, in which a hypochlorite is added to water, and the resultant total amount of organic halogen compounds (TOX formation potential) was measured, and it was applied to the evaluation of trace organic contaminants in ultra-pure water production process. In this investigation, the TOX formation potential of the raw water which was to be used for the ultra-pure water production process, intermediately treated water and ultra-pure water was measured to clarify the behavior of organic substances in the ultra-pure water production process and to demonstrate the usefulness of this procedure to evaluate trace organic contaminants in water. The measurement of TOX formation potential requires no specific technical skill, and only a short time, and gives accurate results, therefore, it is expected that the water quality control in the ultra-pure water production process can be performed more exactly by applying this procedure. (Yoshitake, I.)

O problema da contaminação na determinação de traços de alumínio The problem of contamination in the aluminium trace analysis

Directory of Open Access Journals (Sweden)

Solange Cristina Garcia

1997-08-01

Full Text Available The most common difficulties which occur in trace analysis are those which involve contamination, mainly when the measurement is at very low concentration of ubiquitous elements as aluminium. The worst situation is when a separation step is necessary, because it requires extra-manipulations of the sample. This article describes the degree of contamination and its control for the aluminium trace analysis in dialysis solutions, when aluminium content of about 15 µg/l must be determinated.

Removal of trace metal contaminants from potable water by electrocoagulation

OpenAIRE

Heffron, Joe; Marhefke, Matt; Mayer, Brooke K.

2016-01-01

This study investigated the effects of four operational and environmental variables on the removal of trace metal contaminants from drinking water by electrocoagulation (EC). Removal efficiencies for five metals (arsenic, cadmium, chromium, lead and nickel) were compared under varying combinations of electrode material, post-treatment, water composition and pH. Iron electrodes out-performed aluminum electrodes in removing chromium and arsenic. At pH 6.5, aluminum electrodes were slightly more...

Johor strait as a hotspot for trace elements contamination in peninsular Malaysia.

Science.gov (United States)

Zulkifli, Syaizwan Zahmir; Ismail, Ahmad; Mohamat-Yusuff, Ferdaus; Arai, Takaomi; Miyazaki, Nobuyuki

2010-05-01

Present study was conducted to evaluate current status of trace elements contamination in the surface sediments of the Johor Strait. Iron (2.54 +/- 1.24%) was found as the highest occurring element, followed by those of zinc (210.45 +/- 115.4 microg/g), copper (57.84 +/- 45.54 microg/g), chromium (55.50 +/- 31.24 microg/g), lead (52.52 +/- 28.41 microg/g), vanadium (47.76 +/- 25.76 microg/g), arsenic (27.30 +/- 17.11 microg/g), nickel (18.31 +/- 11.77 microg/g), cobalt (5.13 +/- 3.12 microg/g), uranium (4.72 +/- 2.52 microg/g), and cadmium (0.30 +/- 0.30 microg/g), respectively. Bioavailability of cobalt, nickel, copper, zinc, arsenic and cadmium were higher than 50% of total concentration. Vanadium, copper, zinc, arsenic and cadmium were found significantly different between the eastern and western part of the strait (p Johor Strait is suitable as a hotspot for trace elements contamination related studies.

Tracing contamination sources in soils with Cu and Zn isotopic ratios

Energy Technology Data Exchange (ETDEWEB)

Fekiacova, Z.; Cornu, S. [INRA, UR 1119 Géochimie des Sols et des Eaux, F-13100 Aix en Provence (France); Pichat, S. [Laboratoire de Géologie de Lyon (LGL-TPE), Ecole Normale Supérieure de Lyon, CNRS, UMR 5276, 69007 Lyon (France)

2015-06-01

Copper (Cu) and zinc (Zn) are naturally present and ubiquitous in soils and are important micronutrients. Human activities contribute to the input of these metals to soils in different chemical forms, which can sometimes reach a toxic level for soil organisms and plants. Isotopic signatures could be used to trace sources of anthropogenic Cu and Zn pollution. The aim of this paper is to determine whether it is possible to identify (i) Cu and Zn contamination in soils and their sources, on the basis of their isotopic signatures, and (ii) situations that are a priori favorable or not for tracing Cu and Zn pollution using the isotopic approach. Therefore, we compiled data from the literature on Cu and Zn isotopes in soils, rocks and pollutants and added to this database the results of our own research. As only a few studies have dealt with agricultural contamination, we also studied a soil toposequence from Brittany, France, that experienced spreading of pig slurry for tens of years. In the surface horizons of the natural soils, the δ{sup 65}Cu values vary from − 0.15 to 0.44‰ and the δ{sup 66}Zn from − 0.03 to 0.43‰. Furthermore, vertical variations along soil profiles range from − 0.95 to 0.44‰ for δ{sup 65}Cu and from − 0.53 to 0.64‰ for δ{sup 66}Zn values. We concluded that pedogenetic processes can produce isotopic fractionation, yet, it is not always discernible and can be overprinted by an exogenous isotopic signature. Furthermore, some contaminants are enriched in heavy Cu or in light Zn compared to the rock or soil, but no generalization can be made. The anthropogenic inputs can be identified based on stable Cu and Zn isotope ratios if the isotope ratios of the sources are different from those of the soil, which needs to be tested for each individual case. - Highlights: • Pedogenetic processes produce some Cu and Zn isotope fractionation. • Pollution with distinct isotopic signatures can be traced using Cu and Zn isotopes. • Tracing

Tracing contamination sources in soils with Cu and Zn isotopic ratios

International Nuclear Information System (INIS)

Fekiacova, Z.; Cornu, S.; Pichat, S.

2015-01-01

Copper (Cu) and zinc (Zn) are naturally present and ubiquitous in soils and are important micronutrients. Human activities contribute to the input of these metals to soils in different chemical forms, which can sometimes reach a toxic level for soil organisms and plants. Isotopic signatures could be used to trace sources of anthropogenic Cu and Zn pollution. The aim of this paper is to determine whether it is possible to identify (i) Cu and Zn contamination in soils and their sources, on the basis of their isotopic signatures, and (ii) situations that are a priori favorable or not for tracing Cu and Zn pollution using the isotopic approach. Therefore, we compiled data from the literature on Cu and Zn isotopes in soils, rocks and pollutants and added to this database the results of our own research. As only a few studies have dealt with agricultural contamination, we also studied a soil toposequence from Brittany, France, that experienced spreading of pig slurry for tens of years. In the surface horizons of the natural soils, the δ 65 Cu values vary from − 0.15 to 0.44‰ and the δ 66 Zn from − 0.03 to 0.43‰. Furthermore, vertical variations along soil profiles range from − 0.95 to 0.44‰ for δ 65 Cu and from − 0.53 to 0.64‰ for δ 66 Zn values. We concluded that pedogenetic processes can produce isotopic fractionation, yet, it is not always discernible and can be overprinted by an exogenous isotopic signature. Furthermore, some contaminants are enriched in heavy Cu or in light Zn compared to the rock or soil, but no generalization can be made. The anthropogenic inputs can be identified based on stable Cu and Zn isotope ratios if the isotope ratios of the sources are different from those of the soil, which needs to be tested for each individual case. - Highlights: • Pedogenetic processes produce some Cu and Zn isotope fractionation. • Pollution with distinct isotopic signatures can be traced using Cu and Zn isotopes. • Tracing of the metal

Use of the modified BCR three-step sequential extraction procedure for the study of trace element dynamics in contaminated soils

International Nuclear Information System (INIS)

Pueyo, M.; Mateu, J.; Rigol, A.; Vidal, M.; Lopez-Sanchez, J.F.; Rauret, G.

2008-01-01

The modified BCR three-step sequential extraction procedure was used to examine the temporal dynamics of trace elements in soils contaminated by an accidental spill from an opencast mine in south-west Spain. Soils were mainly contaminated with pyritic sludge and acidic wastewater, whereas some soils were affected only by acidic wastewater. The distributions obtained for both some major (Ca, Fe and Mn) and trace elements (As, Cd, Cu, Pb and Zn) in the sludge and soil samples taken at different times after the accident, 1-3 months and 21 months, were compared. Sequential extractions were useful in identifying different sources of contamination, and in obtaining additional information on the solubility of secondary minerals formed by pyrite oxidation. Thus, the effectiveness of the BCR procedure has proved to be a useful tool for predicting short- and long-term mobility of trace elements, even in complex environmental scenarios. - The modified BCR three-step sequential extraction procedure has proved a useful prediction tool for short- and long-term mobility of trace elements in contaminated soils

Arbuscular mycorrhizal fungi in phytoremediation of contaminated areas by trace elements: mechanisms and major benefits of their applications.

Science.gov (United States)

Cabral, Lucélia; Soares, Claúdio Roberto Fonsêca Sousa; Giachini, Admir José; Siqueira, José Oswaldo

2015-11-01

In recent decades, the concentration of trace elements has increased in soil and water, mainly by industrialization and urbanization. Recovery of contaminated areas is generally complex. In that respect, microorganisms can be of vital importance by making significant contributions towards the establishment of plants and the stabilization of impacted areas. Among the available strategies for environmental recovery, bioremediation and phytoremediation outstand. Arbuscular mycorrhizal fungi (AMF) are considered the most important type of mycorrhizae for phytoremediation. AMF have broad occurrence in contaminated soils, and evidences suggest they improve plant tolerance to excess of certain trace elements. In this review, the use of AMF in phytoremediation and mechanisms involved in their trace element tolerance are discussed. Additionally, we present some techniques used to study the retention of trace elements by AMF, as well as a summary of studies showing major benefits of AMF for phytoremediation.

Utilization of air pollution control residues for the stabilization/solidification of trace element contaminated soil.

Science.gov (United States)

Travar, I; Kihl, A; Kumpiene, J

2015-12-01

The aim of this study was to evaluate the stabilization/solidification (S/S) of trace element-contaminated soil using air pollution control residues (APCRs) prior to disposal in landfill sites. Two soil samples (with low and moderate concentrations of organic matter) were stabilized using three APCRs that originated from the incineration of municipal solid waste, bio-fuels and a mixture of coal and crushed olive kernels. Two APCR/soil mixtures were tested: 30% APCR/70% soil and 50% APCR/50% soil. A batch leaching test was used to study immobilization of As and co-occurring metals Cr, Cu, Pb and Zn. Solidification was evaluated by measuring the unconfined compression strength (UCS). Leaching of As was reduced by 39-93% in APCR/soil mixtures and decreased with increased amounts of added APCR. Immobilization of As positively correlated with the amount of Ca in the APCR and negatively with the amount of soil organic matter. According to geochemical modelling, the precipitation of calcium arsenate (Ca3(AsO4)2/4H2O) and incorporation of As in ettringite (Ca6Al2(SO4)3(OH)12 · 26H2O) in soil/APCR mixtures might explain the reduced leaching of As. A negative effect of the treatment was an increased leaching of Cu, Cr and dissolved organic carbon. Solidification of APCR/soil was considerably weakened by soil organic matter.

The use of transgenic plants in the bioremediation of soils contaminated with trace elements

Energy Technology Data Exchange (ETDEWEB)

Kraemer, U. [Max Planck Inst. of Molecular Plant Physiology, Potsdam (Germany); Chardonnens, A.N. [Faculty of Biology, Bielefeld Univ. (Germany)

2001-07-01

The use of plants to clean-up soils contaminated with trace elements could provide a cheap and sustainable technology for bioremediation. Field trials suggested that the rate of contaminant removal using conventional plants and growth conditions is insufficient. The introduction of novel traits into high biomass plants in a transgenic approach is a promising strategy for the development of effective phytoremediation technologies. This has been exemplified by generating plants able to convert organic and ionic forms of mercury into the less toxic, volatile, elemental mercury, a trait that occurs naturally only in some bacteria and not at all in plants. The engineering of a phytoremediator plant requires the optimization of a number of processes, including trace element mobilization in the soil, uptake into the root, detoxification and allocation within the plant. A number of transgenic plants have been generated in an attempt to modify the tolerance, uptake or homeostasis of trace elements. The phenotypes of these plants provide important insights for the improvement of engineering strategies. A better understanding, both of micronutrient acquisition and homeostasis, and of the genetic, biochemical and physiological basis of metal hyperaccumulation in plants, will be of key importance for the success of phytoremediation. (orig.)

Unit Process Wetlands for Removal of Trace Organic Contaminants and Pathogens from Municipal Wastewater Effluents

Science.gov (United States)

Jasper, Justin T.; Nguyen, Mi T.; Jones, Zackary L.; Ismail, Niveen S.; Sedlak, David L.; Sharp, Jonathan O.; Luthy, Richard G.; Horne, Alex J.; Nelson, Kara L.

2013-01-01

Abstract Treatment wetlands have become an attractive option for the removal of nutrients from municipal wastewater effluents due to their low energy requirements and operational costs, as well as the ancillary benefits they provide, including creating aesthetically appealing spaces and wildlife habitats. Treatment wetlands also hold promise as a means of removing other wastewater-derived contaminants, such as trace organic contaminants and pathogens. However, concerns about variations in treatment efficacy of these pollutants, coupled with an incomplete mechanistic understanding of their removal in wetlands, hinder the widespread adoption of constructed wetlands for these two classes of contaminants. A better understanding is needed so that wetlands as a unit process can be designed for their removal, with individual wetland cells optimized for the removal of specific contaminants, and connected in series or integrated with other engineered or natural treatment processes. In this article, removal mechanisms of trace organic contaminants and pathogens are reviewed, including sorption and sedimentation, biotransformation and predation, photolysis and photoinactivation, and remaining knowledge gaps are identified. In addition, suggestions are provided for how these treatment mechanisms can be enhanced in commonly employed unit process wetland cells or how they might be harnessed in novel unit process cells. It is hoped that application of the unit process concept to a wider range of contaminants will lead to more widespread application of wetland treatment trains as components of urban water infrastructure in the United States and around the globe. PMID:23983451

Unit Process Wetlands for Removal of Trace Organic Contaminants and Pathogens from Municipal Wastewater Effluents.

Science.gov (United States)

Jasper, Justin T; Nguyen, Mi T; Jones, Zackary L; Ismail, Niveen S; Sedlak, David L; Sharp, Jonathan O; Luthy, Richard G; Horne, Alex J; Nelson, Kara L

2013-08-01

Treatment wetlands have become an attractive option for the removal of nutrients from municipal wastewater effluents due to their low energy requirements and operational costs, as well as the ancillary benefits they provide, including creating aesthetically appealing spaces and wildlife habitats. Treatment wetlands also hold promise as a means of removing other wastewater-derived contaminants, such as trace organic contaminants and pathogens. However, concerns about variations in treatment efficacy of these pollutants, coupled with an incomplete mechanistic understanding of their removal in wetlands, hinder the widespread adoption of constructed wetlands for these two classes of contaminants. A better understanding is needed so that wetlands as a unit process can be designed for their removal, with individual wetland cells optimized for the removal of specific contaminants, and connected in series or integrated with other engineered or natural treatment processes. In this article, removal mechanisms of trace organic contaminants and pathogens are reviewed, including sorption and sedimentation, biotransformation and predation, photolysis and photoinactivation, and remaining knowledge gaps are identified. In addition, suggestions are provided for how these treatment mechanisms can be enhanced in commonly employed unit process wetland cells or how they might be harnessed in novel unit process cells. It is hoped that application of the unit process concept to a wider range of contaminants will lead to more widespread application of wetland treatment trains as components of urban water infrastructure in the United States and around the globe.

Contamination analysis unit

International Nuclear Information System (INIS)

Gregg, H.R.; Meltzer, M.P.

1996-01-01

The portable Contamination Analysis Unit (CAU) measures trace quantities of surface contamination in real time. The detector head of the portable contamination analysis unit has an opening with an O-ring seal, one or more vacuum valves and a small mass spectrometer. With the valve closed, the mass spectrometer is evacuated with one or more pumps. The O-ring seal is placed against a surface to be tested and the vacuum valve is opened. Data is collected from the mass spectrometer and a portable computer provides contamination analysis. The CAU can be used to decontaminate and decommission hazardous and radioactive surfaces by measuring residual hazardous surface contamination, such as tritium and trace organics. It provides surface contamination data for research and development applications as well as real-time process control feedback for industrial cleaning operations and can be used to determine the readiness of a surface to accept bonding or coatings. 1 fig

Trace element mobility in a contaminated soil two years after field-amendment with a greenwaste compost mulch

Energy Technology Data Exchange (ETDEWEB)

Clemente, Rafael, E-mail: rclemente@cebas.csic.e [Faculty of Sciences, Liverpool John Moores University, Liverpool L3 3AF (United Kingdom); Hartley, William [Faculty of Sciences, Liverpool John Moores University, Liverpool L3 3AF (United Kingdom); Riby, Philip [School of Pharmacy and Chemistry, Liverpool John Moores University, Liverpool L3 3AF (United Kingdom); Dickinson, Nicholas M.; Lepp, Nicholas W. [Faculty of Sciences, Liverpool John Moores University, Liverpool L3 3AF (United Kingdom)

2010-05-15

Application of greenwaste compost to brownfield land is increasingly common in soil and landscape restoration. Previous studies have demonstrated both beneficial and detrimental effects of this material on trace element mobility. A pot experiment with homogenised soil/compost investigated distribution and mobility of trace elements, two years after application of greenwaste compost mulch to shallow soils overlying a former alkali-works contaminated with Pb, Cu and As (approx900, 200 and 500 mg kg{sup -1}, respectively). Compost mulch increased organic carbon and Fe in soil pore water, which in turn increased As and Sb mobilization; this enhanced uptake by lettuce and sunflower. A very small proportion of the total soil trace element pool was in readily-exchangeable form (<0.01% As, <0.001% other trace elements), but the effect of compost on behaviour of metals was variable and ambiguous. It is concluded that greenwaste compost should be applied with caution to multi-element contaminated soils. - Arsenic solubility and bioavailability increases in soil two years after application of greenwaste compost mulch.

Trace element mobility in a contaminated soil two years after field-amendment with a greenwaste compost mulch

International Nuclear Information System (INIS)

Clemente, Rafael; Hartley, William; Riby, Philip; Dickinson, Nicholas M.; Lepp, Nicholas W.

2010-01-01

Application of greenwaste compost to brownfield land is increasingly common in soil and landscape restoration. Previous studies have demonstrated both beneficial and detrimental effects of this material on trace element mobility. A pot experiment with homogenised soil/compost investigated distribution and mobility of trace elements, two years after application of greenwaste compost mulch to shallow soils overlying a former alkali-works contaminated with Pb, Cu and As (∼900, 200 and 500 mg kg -1 , respectively). Compost mulch increased organic carbon and Fe in soil pore water, which in turn increased As and Sb mobilization; this enhanced uptake by lettuce and sunflower. A very small proportion of the total soil trace element pool was in readily-exchangeable form (<0.01% As, <0.001% other trace elements), but the effect of compost on behaviour of metals was variable and ambiguous. It is concluded that greenwaste compost should be applied with caution to multi-element contaminated soils. - Arsenic solubility and bioavailability increases in soil two years after application of greenwaste compost mulch.

Contamination status of arsenic and other trace elements in drinking water and residents from Tarkwa, a historic mining township in Ghana.

Science.gov (United States)

Asante, Kwadwo Ansong; Agusa, Tetsuro; Subramanian, Annamalai; Ansa-Asare, Osmund D; Biney, Charles A; Tanabe, Shinsuke

2007-01-01

This study was conducted to assess the contamination status of 22 trace elements, especially As in water and residents in Tarkwa, a historic mining town in Ghana. Drinking water and human urine samples were collected from Tarkwa in addition to control samples taken from Accra, the capital of Ghana in March, 2004. Concentrations of As and Mn in some drinking water samples from Tarkwa were found above the WHO drinking water guidelines posing a potential health risk for the people. A potential health risk of As and Mn is a concern for the people consuming the contaminated water in this area. No significant difference of As concentrations in human urine between mining town (Tarkwa) and control site (Accra) was observed. Although As concentrations in drinking water in Tarkwa were low, urinary As levels were comparable to those reported in highly As-affected areas in the world. These results suggest the presence of other sources of As contamination in Ghana. This is the first study on multi-elemental contamination in drinking water and human from a mining town in Ghana.

JPL Contamination Control Engineering

Science.gov (United States)

Blakkolb, Brian

2013-01-01

JPL has extensive expertise fielding contamination sensitive missions-in house and with our NASA/industry/academic partners.t Development and implementation of performance-driven cleanliness requirements for a wide range missions and payloads - UV-Vis-IR: GALEX, Dawn, Juno, WFPC-II, AIRS, TES, et al - Propulsion, thermal control, robotic sample acquisition systems. Contamination control engineering across the mission life cycle: - System and payload requirements derivation, analysis, and contamination control implementation plans - Hardware Design, Risk trades, Requirements V-V - Assembly, Integration & Test planning and implementation - Launch site operations and launch vehicle/payload integration - Flight ops center dot Personnel on staff have expertise with space materials development and flight experiments. JPL has capabilities and expertise to successfully address contamination issues presented by space and habitable environments. JPL has extensive experience fielding and managing contamination sensitive missions. Excellent working relationship with the aerospace contamination control engineering community/.

Contamination Control for Thermal Engineers

Science.gov (United States)

Rivera, Rachel B.

2015-01-01

The presentation will be given at the 26th Annual Thermal Fluids Analysis Workshop (TFAWS 2015) hosted by the Goddard Spaceflight Center (GSFC) Thermal Engineering Branch (Code 545). This course will cover the basics of Contamination Control, including contamination control related failures, the effects of contamination on Flight Hardware, what contamination requirements translate to, design methodology, and implementing contamination control into Integration, Testing and Launch.

Trace element hydrochemistry indicating water contamination in and around the Yangbajing geothermal field, Tibet, China.

Science.gov (United States)

Guo, Qinghai; Wang, Yanxin

2009-10-01

Thirty-eight water samples were collected at Yangbajing to investigate the water contamination resulting from natural geothermal water discharge and anthropogenic geothermal wastewater drainage. The results indicate that snow or snow melting waters, Yangbajing River waters and cold groundwaters are free from geothermal water-related contamination, whereas Zangbo river waters are contaminated by geothermal wastewaters. Moreover, there may exist geothermal springs under the riverbed of a tributary stream of Zangbo River as shown by its Cd, Li, Mo and Pb concentrations. The efforts made in this study show trace element hydrochemistry can well indicate water quality degradation related to geothermal water exploitation.

Contamination and ecological risk assessment of trace elements in sediments of the rivers of Sundarban mangrove forest, Bangladesh.

Science.gov (United States)

Islam, M A; Al-Mamun, A; Hossain, F; Quraishi, S B; Naher, K; Khan, R; Das, S; Tamim, U; Hossain, S M; Nahid, F

2017-11-15

In this study, total concentrations of 16 trace elements (Al, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Cd, Sb, Hg, Pb, Th and U) in sediments of the rivers of the Sundarban mangrove forest, after the catastrophic oil spill accident in the Sela river of Sundarban, were determined. The overall mean concentrations of V, Cr, Fe and Cd in surface sediments of the Sundarban are remarkably higher than available literature data of those elements. Trace element contamination assessment, using different environmental contamination indices, reveals that As, Sb, Th and U are low to moderately contaminated while Cd is moderately to severely contaminated in the sediments of this area. The multivariate statistical analyses were applied to reveal the origin and behavior of the elements during their transport in the mangrove ecosystem. High Cr, Ni, Cu and As concentrations suggest the risk of potentially adverse biological effects in the ecosystem. Copyright © 2017 Elsevier Ltd. All rights reserved.

Application of multivariate analysis to investigate the trace element contamination in top soil of coal mining district in Jorong, South Kalimantan, Indonesia

Science.gov (United States)

Pujiwati, Arie; Nakamura, K.; Watanabe, N.; Komai, T.

2018-02-01

Multivariate analysis is applied to investigate geochemistry of several trace elements in top soils and their relation with the contamination source as the influence of coal mines in Jorong, South Kalimantan. Total concentration of Cd, V, Co, Ni, Cr, Zn, As, Pb, Sb, Cu and Ba was determined in 20 soil samples by the bulk analysis. Pearson correlation is applied to specify the linear correlation among the elements. Principal Component Analysis (PCA) and Cluster Analysis (CA) were applied to observe the classification of trace elements and contamination sources. The results suggest that contamination loading is contributed by Cr, Cu, Ni, Zn, As, and Pb. The elemental loading mostly affects the non-coal mining area, for instances the area near settlement and agricultural land use. Moreover, the contamination source is classified into the areas that are influenced by the coal mining activity, the agricultural types, and the river mixing zone. Multivariate analysis could elucidate the elemental loading and the contamination sources of trace elements in the vicinity of coal mine area.

Trace Element Concentration and Speciation in Selected Mining-Contaminated Soils and Water in Willow Creek Floodplain, Colorado

Directory of Open Access Journals (Sweden)

R. Burt

2011-01-01

Full Text Available Long-term mining activities in the mountains around Creede, Colorado have resulted in significant contamination in soils and water in the Willow Creek floodplain. Total major and trace were determined for soils and water and sequential chemical extraction for soils. Objectives were to determine concentrations and potential reactivity of trace elements and investigate their relationship with other soil and water properties. Water trace elements showed significant variability among sites, ranging from 347 to 12108 μg/L. Relative trend showed (Zn > Sr > Ba > (Mn > W > Cd > (Sn > V ≈ Ni ≈ Cu > Co > (Ag. Soil trace elements showed significant short-range spatial variability, ranging from 2819 to 19274 mg/kg. Relative trend showed (Pb ≈ Zn > Mn > Ba > P > (As > Cu > Sr > V > Cd > Sb ≈ Ag > (Co ≈ Cr > Mo ≈ Sn ≈ Ni > (Be ≈ W > Se ≈ Hg. Predominant fractions were oxide, specifically-sorbed/carbonate bound, and residual. Water soluble and exchangeable fractions showed (Zn ≈ Cd > Pb and Cd > Zn > Pb, respectively. Mobility factors for highly contaminated soils showed Cd ≈ Zn > Pb > Cu > As.

Assessment of soil pollution through trace element contamination in a coal mine environment of Jharia

International Nuclear Information System (INIS)

Singh, Gurdeep; Shrivastava, B.K.

1997-01-01

Coal mining environment is associated with liberation of several trace elements. Soils in such regions particularly have been polluted with these trace elements from a wide range of sources. Trace elements such as lead, copper, iron, zinc, chromium, manganese, cobalt, nickel, cadmium, etc. have caused major human health problems in several parts of the world. Concern over such incidents has prompted numerous investigations into the metabolism and toxic effects of these elements. The trace element contamination of soils (e.g. roadside, overburden dump, residential area etc.) in a part of the Jharia coal field running through a large industrial zone was studied. Representative soil samples from several highly polluted spots of the mining areas were collected and analysed. Results of the investigation revealed that the soils are polluted with trace elements to an appreciable level. Pollution index for soil was developed on the basis of observed concentration levels of trace elements of the study area which may help in better understanding of pollution analysis in coal mining areas. (author)

Contamination Control Techniques

Energy Technology Data Exchange (ETDEWEB)

EBY, J.L.

2000-05-16

Welcome to a workshop on contamination Control techniques. This work shop is designed for about two hours. Attendee participation is encouraged during the workshop. We will address different topics within contamination control techniques; present processes, products and equipment used here at Hanford and then open the floor to you, the attendees for your input on the topics.

Contamination Control Techniques

International Nuclear Information System (INIS)

EBY, J.L.

2000-01-01

Welcome to a workshop on contamination Control techniques. This work shop is designed for about two hours. Attendee participation is encouraged during the workshop. We will address different topics within contamination control techniques; present processes, products and equipment used here at Hanford and then open the floor to you, the attendees for your input on the topics

Contamination control plan for prelaunch operations

Science.gov (United States)

Austin, J. D.

1983-01-01

A unified, systematic plan is presented for contamination control for space flight systems. Allowable contaminant quantities, or contamination budgets, are determined based on system performance margins and system-level allowable degradations. These contamination budgets are compared to contamination rates in ground environments to establish the controls required in each ground environment. The use of feedback from contamination monitoring and some contamination control procedures are discussed.

Trace elements in agroecosystems and impacts on the environment.

Science.gov (United States)

He, Zhenli L; Yang, Xiaoe E; Stoffella, Peter J

2005-01-01

Trace elements mean elements present at low concentrations (mg kg-1 or less) in agroecosystems. Some trace elements, including copper (Cu), zinc (Zn), manganese (Mn), iron (Fe), molybdenum (Mo), and boron (B) are essential to plant growth and are called micronutrients. Except for B, these elements are also heavy metals, and are toxic to plants at high concentrations. Some trace elements, such as cobalt (Co) and selenium (Se), are not essential to plant growth but are required by animals and human beings. Other trace elements such as cadmium (Cd), lead (Pb), chromium (Cr), nickel (Ni), mercury (Hg), and arsenic (As) have toxic effects on living organisms and are often considered as contaminants. Trace elements in an agroecosystem are either inherited from soil parent materials or inputs through human activities. Soil contamination with heavy metals and toxic elements due to parent materials or point sources often occurs in a limited area and is easy to identify. Repeated use of metal-enriched chemicals, fertilizers, and organic amendments such as sewage sludge as well as wastewater may cause contamination at a large scale. A good example is the increased concentration of Cu and Zn in soils under long-term production of citrus and other fruit crops. Many chemical processes are involved in the transformation of trace elements in soils, but precipitation-dissolution, adsorption-desorption, and complexation are the most important processes controlling bioavailability and mobility of trace elements in soils. Both deficiency and toxicity of trace elements occur in agroecosystems. Application of trace elements in fertilizers is effective in correcting micronutrient deficiencies for crop production, whereas remediation of soils contaminated with metals is still costly and difficult although phytoremediation appears promising as a cost-effective approach. Soil microorganisms are the first living organisms subjected to the impacts of metal contamination. Being responsive and

Groundwater contamination with arsenic and other trace elements in an area of the Pampa, province of Cordoba, Argentina

International Nuclear Information System (INIS)

Nicolli, H.B.; Suriano, J.M.; Gomez Peral, M.A.; Ferpozzi, L.H.; Baleani, O.A.

1989-01-01

A geochemical study of the groundwater of the pampa in the province of Cordoba, Argentina, is reported. Physical-chemical parameters, dissolved solids, and seven trace elements were determined in 60 selected water samples. Systematic and accurate measurements of arsenic, fluorine, and vanadium were performed for the first time. The geographic distribution of the seven trace elements was mapped and its correlation with the anion-cation composition of the water was studied. Eighty-four percent of the water analyzed showed arsenic contents over 0.05 mg/l. The maxima for arsenic, fluorine, vanadium, and uranium contents were found in the western part of the study area, in waters dominated by alkali metal cations. Maximum selenium and antimony contents were found in the eastern part of the areas, whereas molybdenum distribution showed no relationship to the other groups. The movements of the subsoil have disturbed surface and subsurface drainage, thus influencing the water salinity and trace element contents. To investigate the origin of contamination, 54 loess samples were collected at wells in depths ranging from the surface down to the water table. This loess, which has a high proportion of volcanic components, mainly rhyolitic glass, exhibits a chemical composition corresponding to that of a dacite. The loess and volcanic glass show anomalous contents of all contaminant trace elements, mainly arsenic and selenium. For this reason, loess is considered to be the most important source of contamination of this ground water area. 30 refs., 6 figs., 9 tab

Activation analysis of hair as an indicator of contamination of man by environmental trace element pollutants

Energy Technology Data Exchange (ETDEWEB)

Ryabukhin, Yu S [ed.

1976-10-01

The burning of fossil fuel, discharges from metallurgical and chemical plants, the wide use of chemicals, and other human activities, result in releasing into the biosphere large quantities of elements which are found in relatively low concentrations in the human organism. The pollution of the biosphere by such trace elements, and in particular heavy metals, has reached such proportions that on the scale of significance of the factors causing the 'stressed' state of the environment of heavy metals occupy the second place and, according to forecasts, may in the future move on to the first. In the problem of pollution of the biosphere, man himself undoubtedly occupies the central position as a target. The pollution of air, soil and water, the contamination of micro-organisms, plants and animals are certainly growing into a serious threat and leading to heavy losses. However, it would be a real disaster if man himself became contaminated to levels giving rise to large scale harmful somatic or genetic effects. It is therefore an urgent problem today to determine the initial levels of trace elements in man and the extent of his contamination in areas where these elements are expected to show anomalous concentrations. Attention should be paid in the first place to those trace elements which probably play no physiological role, are particularly abundant in the environment, and have high toxicity (arsenic, mercury, lead, cadmium, etc.). Moreover, it should be born in mind that in anomalously high concentrations even the physiologically necessary trace elements (copper, zinc, manganese, fluorine, etc.) cause harmful effects. This paper justifies the use of hair samples as a biological indicator of environmental pollutants from physiological and morphological aspect and recommends on sample preparation and analysis methods.

Activation analysis of hair as an indicator of contamination of man by environmental trace element pollutants

International Nuclear Information System (INIS)

Ryabukhin, Yu.S.

1976-10-01

The burning of fossil fuel, discharges from metallurgical and chemical plants, the wide use of chemicals, and other human activities, result in releasing into the biosphere large quantities of elements which are found in relatively low concentrations in the human organism. The pollution of the biosphere by such trace elements, and in particular heavy metals, has reached such proportions that on the scale of significance of the factors causing the 'stressed' state of the environment of heavy metals occupy the second place and, according to forecasts, may in the future move on to the first. In the problem of pollution of the biosphere, man himself undoubtedly occupies the central position as a target. The pollution of air, soil and water, the contamination of micro-organisms, plants and animals are certainly growing into a serious threat and leading to heavy losses. However, it would be a real disaster if man himself became contaminated to levels giving rise to large scale harmful somatic or genetic effects. It is therefore an urgent problem today to determine the initial levels of trace elements in man and the extent of his contamination in areas where these elements are expected to show anomalous concentrations. Attention should be paid in the first place to those trace elements which probably play no physiological role, are particularly abundant in the environment, and have high toxicity (arsenic, mercury, lead, cadmium, etc.). Moreover, it should be born in mind that in anomalously high concentrations even the physiologically necessary trace elements (copper, zinc, manganese, fluorine, etc.) cause harmful effects. This paper justifies the use of hair samples as a biological indicator of environmental pollutants from physiological and morphological aspect and recommends on sample preparation and analysis methods

Mapping human health risks from exposure to trace metal contamination of drinking water sources in Pakistan.

Science.gov (United States)

Bhowmik, Avit Kumar; Alamdar, Ambreen; Katsoyiannis, Ioannis; Shen, Heqing; Ali, Nadeem; Ali, Syeda Maria; Bokhari, Habib; Schäfer, Ralf B; Eqani, Syed Ali Musstjab Akber Shah

2015-12-15

The consumption of contaminated drinking water is one of the major causes of mortality and many severe diseases in developing countries. The principal drinking water sources in Pakistan, i.e. ground and surface water, are subject to geogenic and anthropogenic trace metal contamination. However, water quality monitoring activities have been limited to a few administrative areas and a nationwide human health risk assessment from trace metal exposure is lacking. Using geographically weighted regression (GWR) and eight relevant spatial predictors, we calculated nationwide human health risk maps by predicting the concentration of 10 trace metals in the drinking water sources of Pakistan and comparing them to guideline values. GWR incorporated local variations of trace metal concentrations into prediction models and hence mitigated effects of large distances between sampled districts due to data scarcity. Predicted concentrations mostly exhibited high accuracy and low uncertainty, and were in good agreement with observed concentrations. Concentrations for Central Pakistan were predicted with higher accuracy than for the North and South. A maximum 150-200 fold exceedance of guideline values was observed for predicted cadmium concentrations in ground water and arsenic concentrations in surface water. In more than 53% (4 and 100% for the lower and upper boundaries of 95% confidence interval (CI)) of the total area of Pakistan, the drinking water was predicted to be at risk of contamination from arsenic, chromium, iron, nickel and lead. The area with elevated risks is inhabited by more than 74 million (8 and 172 million for the lower and upper boundaries of 95% CI) people. Although these predictions require further validation by field monitoring, the results can inform disease mitigation and water resources management regarding potential hot spots. Copyright © 2015 Elsevier B.V. All rights reserved.

Regenerable Air Purification System for Gas-Phase Contaminant Control

Science.gov (United States)

Constantinescu, Ileana C.; Finn, John E.; LeVan, M. Douglas; Lung, Bernadette (Technical Monitor)

2000-01-01

Tests of a pre-prototype regenerable air purification system (RAPS) that uses water vapor to displace adsorbed contaminants from an adsorbent column have been performed at NASA Ames Research Center. A unit based on this design can be used for removing trace gas-phase contaminants from spacecraft cabin air or from polluted process streams including incinerator exhaust. During the normal operation mode, contaminants are removed from the air on the column. Regeneration of the column is performed on-line. During regeneration, contaminants are displaced and destroyed inside the closed oxidation loop. In this presentation we discuss initial experimental results for the performance of RAPS in the removal and treatment of several important spacecraft contaminant species from air.

Assessment of trace ground-water contaminants release from south Texas in-situ uranium solution-mining sites

Energy Technology Data Exchange (ETDEWEB)

Kidwell, J.R.; Humenick, M.J.

1981-01-01

The future of uranium solution mining in south Texas depends heavily on the industry's ability to restore production zone ground water to acceptable standards. This study investigated the extent of trace contaminant solubilization during mining and subsequent restoration attempts, first through a literature search centered on uranium control mechanisms, and then by laboratory experiments simulating the mining process. The literature search indicated the complexity of the situation. The number of possible interactions between indigenous elements and materials pointed on the site specificity of the problem. The column studies evaluated three different production area ores. Uranium, molybdenum, arsenic, vanadium, and selenium were analyzed in column effluents. After simulated mining operations were completed, uranium was found to be the most persistent trace element. However, subsequent ground water flushing of the columns could restore in-situ water to EPA recommended drinking water concentrations. Limited data indicated that ground water flowing through mined areas may solubilize molybdenum present in down gradient areas adjacent to the production zone due to increased oxidation potential of ground water if adequate restoration procedures are not followed.

Contamination Control: a systems approach

NARCIS (Netherlands)

Donck, J.C.J. van der

2010-01-01

Contamination influences a wide variety of industrial processes. For complex systems, contamination control, the collective effort to control contamination to such a level that it guarantees or even improves process or product functionality, offers a way for finding workable solutions. Central in

Liver histopathology of the southern watersnake, Nerodia fasciata fasciata, following chronic exposure to trace element-contaminated prey from a coal ash disposal site

Energy Technology Data Exchange (ETDEWEB)

Ganser, L.R.; Hopkins, W.A.; O' Neil, L.; Hasse, S.; Roe, J.H.; Sever, D.M. [St Marys College, Notre Dame, IN (USA). Dept. of Biology

2003-03-01

Previous studies have demonstrated the accumulation of arsenic, cadmium, selenium, strontium, and vanadium in livers of Southern Watersnakes fed fish from a coal-ash contaminated site. Our study is the first to investigate effects of trace element accumulation on cytology of snake liver. Snakes were born in the laboratory and raised for one or two years on diets consisting of varying proportions of contaminated fish. The majority (71%) of snakes fed contaminated prey did not exhibit any differences in liver histology when compared to control snakes fed an uncontaminated diet. In the remaining contaminant-exposed snakes, some aberrations were noted. The most prevalent pathology involved the proliferation of collagen fibers that resulted in narrowing or occlusion of sinusoids and increasing the mass of the intersinsuoidal parenychma. Fibrosis of the liver as a result of chronic injury has been reported previously in reptiles, but this is the first report that links such tissue damage to dietary contamination.

Assessment and control of water contamination associated with shale oil extraction and processing. Progress report, October 1, 1979-September 30, 1980

Energy Technology Data Exchange (ETDEWEB)

Peterson, E.J.; Henicksman, A.V.; Fox, J.P.; O' Rourke, J.A.; Wagner, P.

1982-04-01

The Los Alamos National Laboratory's research on assessment and control of water contamination associated with oil shale operations is directed toward the identification of potential water contamination problems and the evaluation of alternative control strategies for controlling contaminants released into the surface and underground water systems from oil-shale-related sources. Laboratory assessment activities have focused on the mineralogy, trace element concentrations in solids, and leaching characteristics of raw and spent shales from field operations and laboratory-generated spent shales. This report details the chemical, mineralogic, and solution behavior of major, minor, and trace elements in a variety of shale materials (spent shales from Occidental retort 3E at Logan Wash, raw shale from the Colony mine, and laboratory heat-treated shales generated from Colony mine raw shale). Control technology research activities have focused on the definition of control technology requirements based on assessment activities and the laboratory evaluation of alternative control strategies for mitigation of identified problems. Based on results obtained with Logan Wash materials, it appears that the overall impact of in situ processing on groundwater quality (leaching and aquifer bridging) may be less significant than previously believed. Most elements leached from MIS spent shales are already elevated in most groundwaters. Analysis indicates that solubility controls by major cations and anions will aid in mitigating water quality impacts. The exceptions include the trace elements vanadium, lead, and selenium. With respect to in situ retort leaching, process control and multistaged counterflow leaching are evaluated as alternative control strategies for mitigation of quality impacts. The results of these analyses are presented in this report.

Trace metal contamination in mangrove sediments, Guanabara Bay, Rio de Janeiro, Brazil

OpenAIRE

Farias,Cassia O.; Hamacher,Claudia; Wagener,Angela de Luca R.; Campos,Reinaldo C. de; Godoy,José M.

2007-01-01

The Guanabara Bay in Rio de Janeiro has undergone profound alterations of its natural environmental conditions. Metal concentration increase in sediments has been reported to be among these alterations. Trace-metal contamination and availability were studied in sediments of 3 mangrove areas of the bay. Cd, Zn, Pb, Ni, Cu and Al concentrations were determined in segments of sediment cores, after treatment with 1 mol L-1 HCl and with concentrated HNO3. Fe and Mn were determined in the leach wit...

Tracing contamination sources in soils with Cu and Zn isotopic ratios.

Science.gov (United States)

Fekiacova, Z; Cornu, S; Pichat, S

2015-06-01

Copper (Cu) and zinc (Zn) are naturally present and ubiquitous in soils and are important micronutrients. Human activities contribute to the input of these metals to soils in different chemical forms, which can sometimes reach a toxic level for soil organisms and plants. Isotopic signatures could be used to trace sources of anthropogenic Cu and Zn pollution. The aim of this paper is to determine whether it is possible to identify (i) Cu and Zn contamination in soils and their sources, on the basis of their isotopic signatures, and (ii) situations that are a priori favorable or not for tracing Cu and Zn pollution using the isotopic approach. Therefore, we compiled data from the literature on Cu and Zn isotopes in soils, rocks and pollutants and added to this database the results of our own research. As only a few studies have dealt with agricultural contamination, we also studied a soil toposequence from Brittany, France, that experienced spreading of pig slurry for tens of years. In the surface horizons of the natural soils, the δ(65)Cu values vary from -0.15 to 0.44‰ and the δ(66)Zn from -0.03 to 0.43‰. Furthermore, vertical variations along soil profiles range from -0.95 to 0.44‰ for δ(65)Cu and from -0.53 to 0.64‰ for δ(66)Zn values. We concluded that pedogenetic processes can produce isotopic fractionation, yet, it is not always discernible and can be overprinted by an exogenous isotopic signature. Furthermore, some contaminants are enriched in heavy Cu or in light Zn compared to the rock or soil, but no generalization can be made. The anthropogenic inputs can be identified based on stable Cu and Zn isotope ratios if the isotope ratios of the sources are different from those of the soil, which needs to be tested for each individual case. Copyright © 2015 Elsevier B.V. All rights reserved.

The changes in trace metal contamination over the last decade in surface sediments of the Pearl River Estuary, South China.

Science.gov (United States)

Chen, Baowei; Liang, Ximei; Xu, Weihai; Huang, Xiaoping; Li, Xiangdong

2012-11-15

Surface sediments can provide useful information on the recent pollution status of an estuary. One recent field survey was carried out in the Pearl River Estuary (PRE), South China in 2011. The comparisons with previous surveys demonstrated that the concentrations of Ni and Pb in the PRE declined over the last decade, but the concentration of Cu increased in the same time frame. The significant decreases in the concentrations of Ni and Pb were probably due to a reduction of anthropogenic inputs, such as industrial wastewater, into the PRE environment, and the ban imposed on leaded gasoline. Statistical analyses have consistently demonstrated that the process of the sedimentation of fine particles was the dominant factor in controlling the transport and distribution of trace metals in the PRE. The riverine trace metals generally displayed a pattern of diffusion from the northwest to the southeast in the estuary. However, the riparian industrial activities at the east bank of the inner PRE caused significant metal contamination in sediments. In general, effective pollution control measures in the PRD region have decreased the levels of some trace metals in the entire PRE over the last decade with the exception of Cu. Copyright © 2012 Elsevier B.V. All rights reserved.

Trace elements distribution in environmental compartments

Energy Technology Data Exchange (ETDEWEB)

Queiroz, Juliana C. de; Peres, Sueli da Silva; Godoy, Maria Luiza D.P., E-mail: suelip@ird.gov.br [Instituto de Radioprotecao e Dosimetria (IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

2017-11-01

Trace elements term defines the presence of low concentrations metals at environment. Some of them are considered biologically essential, as Co, Cu and Mn. Others can cause detriment to environment and human health, as Pb, Cd, Hg, As, Ti and U. A large number of them have radioactive isotopes, implying the evaluation of risks for human health should be done considering the precepts of environmental radiological protection. The ecosystem pollution with trace elements generates changes at the geochemistry cycle of these elements and in environmental quality. Soils have single characteristics when compared with another components of biosphere (air, water and biota), cause they introduce themselves not only as a drain towards contaminants, but also as natural buffer that control the transport of chemical elements and other substances for atmosphere, hydrosphere and biota. The main purpose of environmental monitoring program is to evaluate the levels of contaminants in the various compartments of the environment: natural or anthropogenic, and to assess the contribution of a potential contaminant source on the environment. Elemental Composition for the collected samples was determined by inductively coupled plasma mass spectroscopy. The main objective of this work was to evaluate the map baseline of concentration of interest trace elements in environmental samples of water, sediment and soil from Environmental Monitoring Program of Instituto de Radioprotecao e Dosimetria (IRD). The samples were analyzed using an inductively coupled plasma mass spectrometer (ICP-MS) at IRD. >From the knowledge of trace elements concentrations, could be evaluated the environmental quality parameters at the studied ecosystems. The data allowed evaluating some relevant aspects of the study of trace elements in soil and aquatic systems, with emphasis at the distribution, concentration and identification of main anthropic sources of contamination at environment. (author)

Trace elements distribution in environmental compartments

International Nuclear Information System (INIS)

Queiroz, Juliana C. de; Peres, Sueli da Silva; Godoy, Maria Luiza D.P.

2017-01-01

Trace elements term defines the presence of low concentrations metals at environment. Some of them are considered biologically essential, as Co, Cu and Mn. Others can cause detriment to environment and human health, as Pb, Cd, Hg, As, Ti and U. A large number of them have radioactive isotopes, implying the evaluation of risks for human health should be done considering the precepts of environmental radiological protection. The ecosystem pollution with trace elements generates changes at the geochemistry cycle of these elements and in environmental quality. Soils have single characteristics when compared with another components of biosphere (air, water and biota), cause they introduce themselves not only as a drain towards contaminants, but also as natural buffer that control the transport of chemical elements and other substances for atmosphere, hydrosphere and biota. The main purpose of environmental monitoring program is to evaluate the levels of contaminants in the various compartments of the environment: natural or anthropogenic, and to assess the contribution of a potential contaminant source on the environment. Elemental Composition for the collected samples was determined by inductively coupled plasma mass spectroscopy. The main objective of this work was to evaluate the map baseline of concentration of interest trace elements in environmental samples of water, sediment and soil from Environmental Monitoring Program of Instituto de Radioprotecao e Dosimetria (IRD). The samples were analyzed using an inductively coupled plasma mass spectrometer (ICP-MS) at IRD. >From the knowledge of trace elements concentrations, could be evaluated the environmental quality parameters at the studied ecosystems. The data allowed evaluating some relevant aspects of the study of trace elements in soil and aquatic systems, with emphasis at the distribution, concentration and identification of main anthropic sources of contamination at environment. (author)

A review of biosensing techniques for detection of trace carcinogen contamination in food products.

Science.gov (United States)

Li, Zhanming; Yu, Yue; Li, Zhiliang; Wu, Tao

2015-04-01

Carcinogen contaminations in the food chain, for example heavy metal ions, pesticides, acrylamide, and mycotoxins, have caused serious health problems. A major objective of food-safety research is the identification and prevention of exposure to these carcinogens, because of their impossible-to-reverse tumorigenic effects. However, carcinogen detection is difficult because of their trace-level presence in food. Thus, reliable and accurate separation and determination methods are essential to protect food safety and human health. This paper summarizes the state of the art in separation and determination methods for analyzing carcinogen contamination, especially the advances in biosensing methods. Furthermore, the application of promising technology including nanomaterials, imprinted polymers, and microdevices is detailed. Challenges and perspectives are also discussed.

Contamination by arsenic and other trace elements of tube-well water along the Mekong River in Lao PDR

International Nuclear Information System (INIS)

Chanpiwat, Penradee; Sthiannopkao, Suthipong; Cho, Kyung Hwa; Kim, Kyoung-Woong; San, Vibol; Suvanthong, Boukeo; Vongthavady, Chantha

2011-01-01

Arsenic and other trace element concentrations were determined for tube-well water collected in the Lao PDR provinces of Attapeu, Bolikhamxai, Champasak, Savannakhet, Saravane, and Vientiane. Water samples, especially from floodplain areas of central and southern Laos, were significantly contaminated not only with As, but with B, Ba, Mn, U, and Fe as well. Total As concentrations ranged from -1 to 278 μg L -1 , with over half exceeding the WHO guideline of 10 μg L -1 . 46% of samples, notably, were dominated by As(III). Samples from Vientiane, further north, were all acceptable except on pH, which was below drinking water limits. A principal component analysis found associations between general water characteristics, As, and other trace elements. Causes of elevated As concentrations in Lao tube wells were considered similar to those in other Mekong River countries, particularly Cambodia and Vietnam, where young alluvial aquifers give rise to reducing conditions. - Research highlights: → Tube-well waters were significantly contaminated with As, B, Ba, Mn, U and Fe. → As contaminated areas were mostly floodplains in the central and southern parts of Laos. → As (III) was a predominant species in 46% of tube-well water samples. → A positive association between water characteristics, B and Sr contents was found. → Total As, As (III) and Fe concentrations were positively associated among each other. - In the first international research on As and other trace element contamination of tube-well water in Lao PDR, concentrations of As, B, Ba, Mn, U, and Fe exceeding drinking water guidelines were found in samples taken mostly from Mekong River floodplain areas.

Contamination by arsenic and other trace elements of tube-well water along the Mekong River in Lao PDR

Energy Technology Data Exchange (ETDEWEB)

Chanpiwat, Penradee [School of Environmental Science and Engineering, Gwangju Institute of Science and Techonology (GIST), 261 Cheomdan-gwagiro (Oryong-dong), Buk-gu, Gwangju 500-712 (Korea, Republic of); Sthiannopkao, Suthipong, E-mail: suthi@gist.ac.k [International Environmental Research Center (IERC), Gwangju Institute of Science and Technology (GIST), 261 Cheomdan-gwagiro - Oryong-dong, Buk-gu, Gwangju 500-712 (Korea, Republic of); Cho, Kyung Hwa [School of Environmental Science and Engineering, Gwangju Institute of Science and Techonology (GIST), 261 Cheomdan-gwagiro (Oryong-dong), Buk-gu, Gwangju 500-712 (Korea, Republic of); Kim, Kyoung-Woong, E-mail: kwkim@gist.ac.k [School of Environmental Science and Engineering, Gwangju Institute of Science and Techonology (GIST), 261 Cheomdan-gwagiro (Oryong-dong), Buk-gu, Gwangju 500-712 (Korea, Republic of); San, Vibol [Department of Environmental Science, Royal University of Phnom Penh (Cambodia); Suvanthong, Boukeo; Vongthavady, Chantha [Environmental Health Division, Center for Environmental Health and Water Supply, Ministry of Health, NongBone Road, Vientiane (Lao People' s Democratic Republic)

2011-02-15

Arsenic and other trace element concentrations were determined for tube-well water collected in the Lao PDR provinces of Attapeu, Bolikhamxai, Champasak, Savannakhet, Saravane, and Vientiane. Water samples, especially from floodplain areas of central and southern Laos, were significantly contaminated not only with As, but with B, Ba, Mn, U, and Fe as well. Total As concentrations ranged from <0.5 {mu}g L{sup -1} to 278 {mu}g L{sup -1}, with over half exceeding the WHO guideline of 10 {mu}g L{sup -1}. 46% of samples, notably, were dominated by As(III). Samples from Vientiane, further north, were all acceptable except on pH, which was below drinking water limits. A principal component analysis found associations between general water characteristics, As, and other trace elements. Causes of elevated As concentrations in Lao tube wells were considered similar to those in other Mekong River countries, particularly Cambodia and Vietnam, where young alluvial aquifers give rise to reducing conditions. - Research highlights: Tube-well waters were significantly contaminated with As, B, Ba, Mn, U and Fe. As contaminated areas were mostly floodplains in the central and southern parts of Laos. As (III) was a predominant species in 46% of tube-well water samples. A positive association between water characteristics, B and Sr contents was found. Total As, As (III) and Fe concentrations were positively associated among each other. - In the first international research on As and other trace element contamination of tube-well water in Lao PDR, concentrations of As, B, Ba, Mn, U, and Fe exceeding drinking water guidelines were found in samples taken mostly from Mekong River floodplain areas.

Engineering hyporheic zones for the attenuation of urban pesticides and other stormwater trace organic contaminants

Science.gov (United States)

Portmann, A. C.; Halpin, B. N.; Herzog, S.; Higgins, C.; McCray, J. E.

2017-12-01

The hyporheic zone (HZ) is a natural bioreactor that can provide in-stream attenuation of various nonpoint source contaminants. Main contributions of nonpoint source pollution are coming from urban stormwater and agricultural runoff, which both adversely impact aquatic life. Stormwater pollutants of concern commonly include nutrients, metals, pathogens, and trace organic contaminants (TOrCs). Despite substantial water quality challenges, current stormwater management typically focuses on water quantity issues rather than pollutant removal. Furthermore, current HZ restoration best management practices do not explicitly control HZ residence times, and generally only induce localized effects. To increase hyporheic exchange and therefore improving water quality, we introduced engineered streambeds featuring modifications to subsurface hydraulic conductivity (K) and reactivity - termed Biohydrochemical Enhancements for Streamwater Treatment (BEST). BEST modifications comprise subsurface modules that employ 1) low-permeability sediments to drive hyporheic exchange and control subsurface residence times, and 2) permeable reactive geomedia to change reaction rates within the HZ. Here we present performance data collected in constructed stream experiments, comparing an all-sand control condition with a stream containing BEST modules and a mixture of 70/30 sand/woodchips (v/v). We evaluated the attenuation of a suite of TOrCs in the BEST versus the control system for two different streambed media: a coarse sand with K = 0.48 cm/s and a fine sand with K = 0.16 cm/s. The range of TOrCs investigated comprises urban pesticides and other stormwater relevant TOrCs. Benefits of applying BEST include increased exchange between streamwater and HZ water, leading to diverse redox conditions that are beneficial for aquatic organisms and will facilitate in-stream pollutant transformation. Future work will focus on tailoring the BEST design for specific pollutants, thereby controlling HZ

Spectroscopic Determination of Trace Contaminants in High Purity Oxygen

Science.gov (United States)

Hornung, Steven D.

2011-01-01

Oxygen used for extravehicular activities (EVA) must be free of contaminants because a difference in a few tenths of a percent of argon or nitrogen content can mean significant reduction in available EVA time. These inert gases build up in the extravehicular mobility unit because they are not metabolized or scrubbed from the atmosphere. Measurement of oxygen purity above 99.5% is problematic, and currently only complex instruments such as gas chromatographs or mass spectrometers are used for these determinations. Because liquid oxygen boil-off from the space shuttle will no longer be available to supply oxygen for EVA use, other concepts are being developed to produce and validate high purity oxygen from cabin air aboard the International Space Station. A prototype optical emission technique capable of detecting argon and nitrogen below 0.1% in oxygen was developed at White Sands Test Facility. This instrument uses a glow discharge in reduced pressure gas to produce atomic emission from the species present. Because the atomic emission lines from oxygen, nitrogen, and argon are discrete and in many cases well-separated, trace amounts of argon and nitrogen can be detected in the ultraviolet and visible spectrum. This is a straightforward, direct measurement of the target contaminants and may lend itself to a device capable of on-orbit verification of oxygen purity. System design and optimized measurement parameters are presented.

Analysis of Process Gases and Trace Contaminants in Membrane-Aerated Gaseous Effluent Streams.

Science.gov (United States)

Coutts, Janelle L.; Lunn, Griffin Michael; Meyer, Caitlin E.

2015-01-01

In membrane-aerated biofilm reactors (MABRs), hollow fibers are used to supply oxygen to the biofilms and bulk fluid. A pressure and concentration gradient between the inner volume of the fibers and the reactor reservoir drives oxygen mass transport across the fibers toward the bulk solution, providing the fiber-adhered biofilm with oxygen. Conversely, bacterial metabolic gases from the bulk liquid, as well as from the biofilm, move opposite to the flow of oxygen, entering the hollow fiber and out of the reactor. Metabolic gases are excellent indicators of biofilm vitality, and can aid in microbial identification. Certain gases can be indicative of system perturbations and control anomalies, or potentially unwanted biological processes occurring within the reactor. In confined environments, such as those found during spaceflight, it is important to understand what compounds are being stripped from the reactor and potentially released into the crew cabin to determine the appropriateness or the requirement for additional mitigation factors. Reactor effluent gas analysis focused on samples provided from Kennedy Space Center's sub-scale MABRs, as well as Johnson Space Center's full-scale MABRs, using infrared spectroscopy and gas chromatography techniques. Process gases, such as carbon dioxide, oxygen, nitrogen, nitrogen dioxide, and nitrous oxide, were quantified to monitor reactor operations. Solid Phase Microextraction (SPME) GC-MS analysis was used to identify trace volatile compounds. Compounds of interest were subsequently quantified. Reactor supply air was examined to establish target compound baseline concentrations. Concentration levels were compared to average ISS concentration values and/or Spacecraft Maximum Allowable Concentration (SMAC) levels where appropriate. Based on a review of to-date results, current trace contaminant control systems (TCCS) currently on board the ISS should be able to handle the added load from bioreactor systems without the need

Alleviation of environmental risks associated with severely contaminated mine tailings using amendments: Modeling of trace element speciation, solubility, and plant accumulation.

Science.gov (United States)

Pardo, Tania; Bes, Cleménce; Bernal, Maria Pilar; Clemente, Rafael

2016-11-01

Tailings are considered one of the most relevant sources of contamination associated with mining activities. Phytostabilization of mine spoils may need the application of the adequate combination of amendments to facilitate plant establishment and reduce their environmental impact. Two pot experiments were set up to assess the capability of 2 inorganic materials (calcium carbonate and a red mud derivate, ViroBind TM ), alone or in combination with organic amendments, for the stabilization of highly acidic trace element-contaminated mine tailings using Atriplex halimus. The effects of the treatments on tailings and porewater physico-chemical properties and trace-element accumulation by the plants, as well as the processes governing trace elements speciation and solubility in soil solution and their bioavailability were modeled. The application of the amendments increased tailings pH and decreased (>99%) trace elements solubility in porewater, but also changed the speciation of soluble Cd, Cu, and Pb. All the treatments made A. halimus growth in the tailings possible; organic amendments increased plant biomass and nutritional status, and reduced trace-element accumulation in the plants. Tailings amendments modified trace-element speciation in porewater (favoring the formation of chlorides and/or organo-metallic forms) and their solubility and plant uptake, which were found to be mainly governed by tailing/porewater pH, electrical conductivity, and organic carbon content, as well as soluble/available trace-element concentrations. Environ Toxicol Chem 2016;35:2874-2884. © 2016 SETAC. © 2016 SETAC.

A cleanroom contamination control system

OpenAIRE

Whyte, W.; Eaton, T.

2002-01-01

Analytical methods for hazard and risk analysis are being considered for controlling contamination\\ud in pharmaceutical cleanrooms. The most suitable method appears to be the HACCP system that has\\ud been developed for the food industry, but this requires some reinterpretation for use in\\ud pharmaceutical manufacturing. This paper suggests a possible system.\\ud To control contamination effectively, it is necessary to have a good appreciation of the routes and\\ud sources of contamination, and ...

49 CFR 176.715 - Contamination control.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Contamination control. 176.715 Section 176.715... Requirements for Radioactive Materials § 176.715 Contamination control. Each hold, compartment, or deck area... the removable (non-fixed) radioactive surface contamination is not greater than the limits prescribed...

49 CFR 173.443 - Contamination control.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Contamination control. 173.443 Section 173.443... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.443 Contamination control. (a) The level of non-fixed (removable) radioactive contamination on the external surfaces of each package offered for...

The role of plant-associated bacteria in the mobilization and phytoextraction of trace elements in contaminated soils.

Science.gov (United States)

Sessitsch, Angela; Kuffner, Melanie; Kidd, Petra; Vangronsveld, Jaco; Wenzel, Walter W; Fallmann, Katharina; Puschenreiter, Markus

2013-05-01

Phytoextraction makes use of trace element-accumulating plants that concentrate the pollutants in their tissues. Pollutants can be then removed by harvesting plants. The success of phytoextraction depends on trace element availability to the roots and the ability of the plant to intercept, take up, and accumulate trace elements in shoots. Current phytoextraction practises either employ hyperaccumulators or fast-growing high biomass plants; the phytoextraction process may be enhanced by soil amendments that increase trace element availability in the soil. This review will focus on the role of plant-associated bacteria to enhance trace element availability in the rhizosphere. We report on the kind of bacteria typically found in association with trace element - tolerating or - accumulating plants and discuss how they can contribute to improve trace element uptake by plants and thus the efficiency and rate of phytoextraction. This enhanced trace element uptake can be attributed to a microbial modification of the absorptive properties of the roots such as increasing the root length and surface area and numbers of root hairs, or by increasing the plant availability of trace elements in the rhizosphere and the subsequent translocation to shoots via beneficial effects on plant growth, trace element complexation and alleviation of phytotoxicity. An analysis of data from literature shows that effects of bacterial inoculation on phytoextraction efficiency are currently inconsistent. Some key processes in plant-bacteria interactions and colonization by inoculated strains still need to be unravelled more in detail to allow full-scale application of bacteria assisted phytoremediation of trace element contaminated soils.

Contamination by trace elements at e-waste recycling sites in Bangalore, India.

Science.gov (United States)

Ha, Nguyen Ngoc; Agusa, Tetsuro; Ramu, Karri; Tu, Nguyen Phuc Cam; Murata, Satoko; Bulbule, Keshav A; Parthasaraty, Peethmbaram; Takahashi, Shin; Subramanian, Annamalai; Tanabe, Shinsuke

2009-06-01

The recycling and disposal of electronic waste (e-waste) in developing countries is causing an increasing concern due to its effects on the environment and associated human health risks. To understand the contamination status, we measured trace elements (TEs) in soil, air dust, and human hair collected from e-waste recycling sites (a recycling facility and backyard recycling units) and the reference sites in Bangalore and Chennai in India. Concentrations of Cu, Zn, Ag, Cd, In, Sn, Sb, Hg, Pb, and Bi were higher in soil from e-waste recycling sites compared to reference sites. For Cu, Sb, Hg, and Pb in some soils from e-waste sites, the levels exceeded screening values proposed by US Environmental Protection Agency (EPA). Concentrations of Cr, Mn, Co, Cu, In, Sn, Sb, Tl, Pb and Bi in air from the e-waste recycling facility were relatively higher than the levels in Chennai city. High levels of Cu, Mo, Ag, Cd, In, Sb, Tl, and Pb were observed in hair of male workers from e-waste recycling sites. Our results suggest that e-waste recycling and its disposal may lead to the environmental and human contamination by some TEs. To our knowledge, this is the first study on TE contamination at e-waste recycling sites in Bangalore, India.

Catalyst Substrates Remove Contaminants, Produce Fuel

Science.gov (United States)

2012-01-01

A spacecraft is the ultimate tight building. We don t want any leaks, and there is very little fresh air coming in, says Jay Perry, an aerospace engineer at Marshall Space Flight Center. As a result, there is a huge potential for a buildup of contaminants from a host of sources. Inside a spacecraft, contaminants can be introduced from the materials that make spacecraft components, electronics boxes, or activities by the crew such as food preparation or cleaning. Humans also generate contaminants by breathing and through the body s natural metabolic processes. As part of the sophisticated Environmental Control and Life Support System on the International Space Station (ISS), a trace contaminant control system removes carbon dioxide and other impurities from the cabin atmosphere. To maintain healthy levels, the system uses adsorbent media to filter chemical contaminant molecules and a high-temperature catalytic oxidizer to change the chemical structure of the contaminants to something more benign, usually carbon dioxide and water. In the 1990s, while researching air quality control technology for extended spaceflight travel, Perry and others at Marshall were looking for a regenerable process for the continuous removal of carbon dioxide and trace chemical contaminants on long-duration manned space flights. At the time, the existing technology used on U.S. spacecraft could only be used once, which meant that a spacecraft had to carry additional spare parts for use in case the first one was depleted, or the spacecraft would have to return to Earth to exchange the components.

Searching for traces of life in subglacial Lake Vostok (Antarctica) in terms of forward contamination: the lessons for exploration of icy environments on Mars

Science.gov (United States)

Bulat, S. A.; Alekhina, I. A.; Lipenkov, V. Ya.; Petit, J.-R.

Bacterial 16S ribosomal gene analysis guarded by criteria for trace DNA analysis and Ancient DNA research clearly testifies for the very low biomass in accretion ice from giant subglacial Lake Vostok buried beneath 4-km thick East Antarctic ice sheet. It seems that the accretion ice is essentially germ-free indicating that the water body should also be hosting a highly sparse life, if any, unless the lake water lost its biological contents during accretion process. Due to this the search for life in Lake Vostok is constrained by a high chance of contamination similar to forward-contamination upon searching for life on Mars and other icy planets. Of 16 bacterial phylotypes initially recovered from the accretion ice the only one was kept with confident relevance to the lake environment while 15 others were presumed to be contaminants on the basis of indexing contaminant criteria developed for Lake Vostok and similar icy environments. The current way to avoid contamination appears to use stringent ice chemistry-based decontamination procedures and comprehensive biological controls including establishment of contemporary contaminant database as a prerequisite to identify and categorize sources of contaminants. More challenge would be to advance cleanliness and sterilization approaches and procedures in order to achieve and measure the level of cleanliness appropriate for tools exploring environments like Lake Vostok. As a guide for searching for life in (sub)glacial environments on Earth or Mars and Jovian's Europa our recommendations can be summarized as follows: (i) apply stringent ice decontamination procedures to meet chemistry and trace DNA analysis standards, (ii) document biological contents of various environments including humans in contact with ice samples (development of contaminant database), (iii) ensure in using relevant methods to cover both known and expected biodiversity and (iv) verify microbial findings through their possible metabolic profiles

Arbuscular mycorrhizal fungal inoculation protects Miscanthus × giganteus against trace element toxicity in a highly metal-contaminated site.

Science.gov (United States)

Firmin, Stéphane; Labidi, Sonia; Fontaine, Joël; Laruelle, Frédéric; Tisserant, Benoit; Nsanganwimana, Florian; Pourrut, Bertrand; Dalpé, Yolande; Grandmougin, Anne; Douay, Francis; Shirali, Pirouz; Verdin, Anthony; Lounès-Hadj Sahraoui, Anissa

2015-09-15

Arbuscular mycorrhizal fungus (AMF)-assisted phytoremediation could constitute an ecological and economic method in polluted soil rehabilitation programs. The aim of this work was to characterize the trace element (TE) phytoremediation potential of mycorrhizal Miscanthus × giganteus. To understand the mechanisms involved in arbuscular mycorrhizal symbiosis tolerance to TE toxicity, the fatty acid compositions and several stress oxidative biomarkers were compared in the roots and leaves of Miscanthus × giganteus cultivated under field conditions in either TE-contaminated or control soils. TEs were accumulated in greater amounts in roots, but the leaves were the organ most affected by TE contamination and were characterized by a strong decrease in fatty acid contents. TE-induced oxidative stress in leaves was confirmed by an increase in the lipid peroxidation biomarker malondialdehyde (MDA). TE contamination decreased the GSSG/GSH ratio in the leaves of exposed plants, while peroxidase (PO) and superoxide dismutase (SOD) activities were increased in leaves and in whole plants, respectively. AMF inoculation also increased root colonization in the presence of TE contamination. The mycorrhizal colonization determined a decrease in SOD activity in the whole plant and PO activities in leaves and induced a significant increase in the fatty acid content in leaves and a decrease in MDA formation in whole plants. These results suggested that mycorrhization is able to confer protection against oxidative stress induced by soil pollution. Our findings suggest that mycorrhizal inoculation could be used as a bioaugmentation technique, facilitating Miscanthus cultivation on highly TE-contaminated soil. Copyright © 2015. Published by Elsevier B.V.

Rationale and Methods for Archival Sampling and Analysis of Atmospheric Trace Chemical Contaminants On Board Mir and Recommendations for the International Space Station

Science.gov (United States)

Perry, J. L.; James, J. T.; Cole, H. E.; Limero, T. F.; Beck, S. W.

1997-01-01

Collection and analysis of spacecraft cabin air samples are necessary to assess the cabin air quality with respect to crew health. Both toxicology and engineering disciplines work together to achieve an acceptably clean cabin atmosphere. Toxicology is concerned with limiting the risk to crew health from chemical sources, setting exposure limits, and analyzing air samples to determine how well these limits are met. Engineering provides the means for minimizing the contribution of the various contaminant generating sources by providing active contamination control equipment on board spacecraft and adhering to a rigorous material selection and control program during the design and construction of the spacecraft. A review of the rationale and objectives for sampling spacecraft cabin atmospheres is provided. The presently-available sampling equipment and methods are reviewed along with the analytical chemistry methods employed to determine trace contaminant concentrations. These methods are compared and assessed with respect to actual cabin air quality monitoring needs. Recommendations are presented with respect to the basic sampling program necessary to ensure an acceptably clean spacecraft cabin atmosphere. Also, rationale and recommendations for expanding the scope of the basic monitoring program are discussed.

Prioritizing research for trace pollutants and emerging contaminants in the freshwater environment

Energy Technology Data Exchange (ETDEWEB)

Murray, Kyle E., E-mail: Kyle.Murray@utsa.ed [Center for Water Research, University of Texas at San Antonio, One UTSA Circle, San Antonio, TX 78249-0663 (United States); Thomas, Sheeba M [San Antonio River Authority, San Antonio, TX (United States); Bodour, Adria A [Air Force Center for Engineering and the Environment (AFCEE), Brooks City-Base, TX (United States)

2010-12-15

Organic chemicals have been detected at trace concentrations in the freshwater environment for decades. Though the term trace pollutant indicates low concentrations normally in the nanogram or microgram per liter range, many of these pollutants can exceed an acceptable daily intake (ADI) for humans. Trace pollutants referred to as emerging contaminants (ECs) have recently been detected in the freshwater environment and may have adverse human health effects. Analytical techniques continue to improve; therefore, the number and frequency of detections of ECs are increasing. It is difficult for regulators to restrict use of pollutants that are a human health hazard; scientists to improve treatment techniques for higher priority pollutants; and the public to modify consumption patterns due to the vast number of ECs and the breadth of literature on the occurrence, use, and toxicity. Hence, this paper examines literature containing occurrence and toxicity data for three broad classes of trace pollutants and ECs (industrials, pesticides, and pharmaceuticals and personal care products (PPCPs)), and assesses the relevance of 71 individual compounds. The evaluation indicates that widely used industrials (BPF) and PPCPs (AHTN, HHCB, ibuprofen, and estriol) occur frequently in samples from the freshwater environment but toxicity data were not available; thus, it is important to establish their ADI. Other widely used industrials (BDE-47, BDE-99) and pesticides (benomyl, carbendazim, aldrin, endrin, ethion, malathion, biphenthrin, and cypermethrin) have established ADI values but occurrence in the freshwater environment was not well documented. The highest priority pollutants for regulation and treatment should include industrials (PFOA, PFOS and DEHP), pesticides (diazinon, methoxychlor, and dieldrin), and PPCPs (EE2, carbamazepine, {beta}E2, DEET, triclosan, acetaminophen, and E1) because they occur frequently in the freshwater environment and pose a human health hazard at

Prioritizing research for trace pollutants and emerging contaminants in the freshwater environment

International Nuclear Information System (INIS)

Murray, Kyle E.; Thomas, Sheeba M.; Bodour, Adria A.

2010-01-01

Organic chemicals have been detected at trace concentrations in the freshwater environment for decades. Though the term trace pollutant indicates low concentrations normally in the nanogram or microgram per liter range, many of these pollutants can exceed an acceptable daily intake (ADI) for humans. Trace pollutants referred to as emerging contaminants (ECs) have recently been detected in the freshwater environment and may have adverse human health effects. Analytical techniques continue to improve; therefore, the number and frequency of detections of ECs are increasing. It is difficult for regulators to restrict use of pollutants that are a human health hazard; scientists to improve treatment techniques for higher priority pollutants; and the public to modify consumption patterns due to the vast number of ECs and the breadth of literature on the occurrence, use, and toxicity. Hence, this paper examines literature containing occurrence and toxicity data for three broad classes of trace pollutants and ECs (industrials, pesticides, and pharmaceuticals and personal care products (PPCPs)), and assesses the relevance of 71 individual compounds. The evaluation indicates that widely used industrials (BPF) and PPCPs (AHTN, HHCB, ibuprofen, and estriol) occur frequently in samples from the freshwater environment but toxicity data were not available; thus, it is important to establish their ADI. Other widely used industrials (BDE-47, BDE-99) and pesticides (benomyl, carbendazim, aldrin, endrin, ethion, malathion, biphenthrin, and cypermethrin) have established ADI values but occurrence in the freshwater environment was not well documented. The highest priority pollutants for regulation and treatment should include industrials (PFOA, PFOS and DEHP), pesticides (diazinon, methoxychlor, and dieldrin), and PPCPs (EE2, carbamazepine, βE2, DEET, triclosan, acetaminophen, and E1) because they occur frequently in the freshwater environment and pose a human health hazard at

Analysis of the Ability of United States and Russian Trace Contaminant Control Systems to Meet U.S. 180-Day and Russian 360-Day Spacecraft Maximum Allowable Concentrations

Science.gov (United States)

Perry, J. L.

2016-01-01

As the Space Station Freedom program transitioned to become the International Space Station (ISS), uncertainty existed concerning the performance capabilities for U.S.- and Russian-provided trace contaminant control (TCC) equipment. In preparation for the first dialogue between NASA and Russian Space Agency personnel in Moscow, Russia, in late April 1994, an engineering analysis was conducted to serve as a basis for discussing TCC equipment engineering assumptions as well as relevant assumptions on equipment offgassing and cabin air quality standards. The analysis presented was conducted as part of the efforts to integrate Russia into the ISS program via the early ISS Multilateral Medical Operations Panel's Air Quality Subgroup deliberations. This analysis, served as a basis for technical deliberations that established a framework for TCC system design and operations among the ISS program's international partners that has been instrumental in successfully managing the ISS common cabin environment.

RCT: 2.05 Contamination Control, Course #8770

Energy Technology Data Exchange (ETDEWEB)

Hillmer, Kurt T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-05-23

This report focuses on the detection and control of radioactive contamination, which are an integral part of an aggressive ALARA program and provide an indication of the effectiveness of engineering controls and proper work practices in preventing the release of radioactive material. Radioactive contamination, if undetected or not properly controlled, can be spread and contaminate areas, equipment, personnel, and the environment.

10 CFR 39.69 - Radioactive contamination control.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Radioactive contamination control. 39.69 Section 39.69... Radiation Safety Requirements § 39.69 Radioactive contamination control. (a) If the licensee detects evidence that a sealed source has ruptured or licensed materials have caused contamination, the licensee...

Chemical barriers for controlling groundwater contamination

International Nuclear Information System (INIS)

Morrison, S.J.; Spangler, R.R.

1993-01-01

Chemical barriers are being explored as a low-cost means of controlling groundwater contamination. The barrier can intercept a contaminant plume and prevent migration by transferring contaminants from the groundwater to immobile solids. A chemical barrier can be emplaced in a landfill liner or in an aquifer cutoff wall or can be injected into a contaminant plume. Chemical barriers can be classified as either precipitation barriers or sorption barriers depending upon the dominant mode of contaminant extraction. In a precipitation barrier, contaminants are bound in the structures of newly formed phases; whereas, in a sorption barrier, contaminants attach to the surfaces of preexisting solids by adsorption or some other surface mechanism. Sorption of contaminants is pH dependent. A precipitation barrier can control the pH of the system, but alkaline groundwater may dominate the pH in a sorption barrier. A comparison is made of the characteristics of precipitation and sorption barriers. Experimental data on the extraction of uranium and molybdenum from simulated groundwater are used to demonstrate these concepts. 10 refs., 9 figs., 1 tab

Trace contaminant concentration affects mineral transformation and pollutant fate in hydroxide-weathered Hanford sediments

International Nuclear Information System (INIS)

Perdrial, Nicolas; Rivera, Nelson; Thompson, Aaron; O’Day, Peggy A.; Chorover, Jon

2011-01-01

Highlights: ► Fate of Sr, Cs and I tracked during hydroxide-weathering of sediments. ► pCO 2 and contaminant concentration affected mineral transformation. ► Sodalite/cancrinite formed at μM levels, chabazite at mM levels. ► Absence of CO 2 resulted in calcite dissolution and strätlingite formation. ► Trace contaminant concentrations modified their own sequestration path. - Abstract: Prior work has shown that when silicaceous sediments are infused with caustic radioactive waste, contaminant fate is tightly coupled to ensuing mineral weathering reactions. However, the effects of local aqueous geochemical conditions on these reactions are poorly studied. Thus, we varied contaminant concentration and pCO 2 during the weathering of previously uncontaminated Hanford sediments over 6 months and 1 year in a solution of caustic waste (pH 13, high ionic strength). Co-contaminants Sr, Cs and I were added at “low” (Cs/Sr: 10 −5 m; I: 10 −7 m) and “high” (Cs/Sr: 10 −3 m; I: 10 −5 m) concentrations, and headspace was held at atmospheric or undetectable ( 2 partial pressure. Solid phase characterization revealed the formation of the zeolite chabazite in “high” samples, whereas feldspathoids, sodalite and cancrinite, were formed preferentially in “low” samples. Sr, Cs and I were sequestered in all reacted sediments. Native calcite dissolution in the CO 2 -free treatment drove the formation of strätlingite (Ca 2 Al 2 SiO 7 ·8H 2 O) and diminished availability of Si and Al for feldspathoid formation. Results indicate that pCO 2 and contaminant concentrations strongly affect contaminant speciation in waste-weathered sediments, and are therefore likely to impact reaction product stability under any remediation scenario.

Tracing and control of raw materials sourcing for vaccine manufacturers.

Science.gov (United States)

Faretra Peysson, Laurence

2010-05-01

The control of the raw materials used to manufacture vaccines is mandatory; therefore, a very clear process must be in place to guarantee that raw materials are traced. Those who make products or supplies used in vaccine manufacture (suppliers of culture media, diagnostic tests, etc.) must apply quality systems proving that they adhere to certain standards. ISO certification, Good Manufacturing Practices for production sites and the registration of culture media with a 'Certificate of Suitability' from the European Directorate for the Quality of Medicines and Healthcare are reliable quality systems pertaining to vaccine production. Suppliers must assure that each lot of raw materials used in a product that will be used in vaccine manufacture adheres to the level of safety and traceability required. Incoming materials must be controlled in a single 'Enterprise Resource Planning' system which is used to document important information, such as the assignment of lot number, expiration date, etc. Ingredients for culture media in particular must conform to certain specifications. The specifications that need to be checked vary according to the ingredient, based on the level of risk. The way a raw material is produced is also important, and any aspect relative to cross-contamination, such as the sanitary measures used in producing and storing the raw material must be checked as well. In addition, suppliers can reduce the risk of viral contamination of raw materials by avoiding purchases in countries where a relevant outbreak is currently declared. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

A Market Basket Survey of Horticultural Fruits for Arsenic and Trace Metal Contamination in Southeast Nigeria and Potential Health Risk Implications

OpenAIRE

Chigozie Damian Ezeonyejiaku; Maximilian Obinna Obiakor

2017-01-01

Background. Elevated arsenic and trace metal contamination of the terrestrial food chain represents one of the most significant environmental risk exposures for human populations in developing countries. Metalloid and metal contamination in horticultural crop produce such as fruit is a public health concern in Nigeria. Local fruits are cheap sources of vitamins and minerals for the resident population and pose an important dietary threat of metal(loid) toxicity through consumption. Objecti...

Tracey - a simulation model of trace element fluxes in soil-plant system for long-term assessment of a radioactive groundwater contamination

International Nuclear Information System (INIS)

Gaerdenaes, Annemieke; Eckersten, Henrik; Reinlert, Andre; Gustafsson, David; Jansson, Per-Erik; Ekstroem, Per-Anders; Avila, Rodolfo; Greger, Maria

2009-10-01

We developed a general trace element model called Tracey to simulate dynamically the possible accumulation of radionuclides as a result of an long-term radioactive contamination of groundwater in terrestrial ecosystems. The overall objectives of the study are to: 1) Develop and evaluate a multi-compartmental model that dynamically simulates the transport and accumulation of a radionuclide in the soil-plant system at a time scale relevant for risk assessment of nuclear fuel waste; and 2) Asses the possible accumulation of radionuclide in terrestrial ecosystems due to an eventual long-term continuous radioactive groundwater contamination. Specific objectives were to assess: - The proportion of the contamination accumulated and where it is stored in the ecosystem. - The importance of the plant uptake approach for accumulation of radionuclides. - The most important radionuclide properties and ecosystem characteristics for accumulation and losses. - The proportion of the contamination lost and how is it lost. - The circumstances which stimulated export of radionuclides to other ecosystems. The model presented here, called Tracey, is a stand-alone version to allow for long simulation periods relevant for the time scale of risk assessment of nuclear waste (i.e. several thousand years) with time steps as short as one day. Tracey is a multi-compartmental model in which fluxes and storage of radionuclide are described for different plant parts and for several soil layers. Each layer includes pools of slowly and quickly decomposing litter, humus, solved and absorbed trace element. The trace element fluxes are assumed to be proportional to either water or carbon fluxes, these fluxes are simulated using the dynamic model CoupModel for fluxes of water, carbon, nitrogen and carbon in terrestrial ecosystems. Two different model approaches were used to describe plant uptake of radionuclides. The one called passive uptake approach is driven by water uptake and the one called active

Sensitive Multi-Species Emissions Monitoring: Infrared Laser-Based Detection of Trace-Level Contaminants

Energy Technology Data Exchange (ETDEWEB)

Steill, Jeffrey D. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Huang, Haifeng [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Hoops, Alexandra A. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Patterson, Brian D. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Birtola, Salvatore R. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Jaska, Mark [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Strecker, Kevin E. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Chandler, David W. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Bisson, Soott [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2014-09-01

This report summarizes our development of spectroscopic chemical analysis techniques and spectral modeling for trace-gas measurements of highly-regulated low-concentration species present in flue gas emissions from utility coal boilers such as HCl under conditions of high humidity. Detailed spectral modeling of the spectroscopy of HCl and other important combustion and atmospheric species such as H 2 O, CO 2 , N 2 O, NO 2 , SO 2 , and CH 4 demonstrates that IR-laser spectroscopy is a sensitive multi-component analysis strategy. Experimental measurements from techniques based on IR laser spectroscopy are presented that demonstrate sub-ppm sensitivity levels to these species. Photoacoustic infrared spectroscopy is used to detect and quantify HCl at ppm levels with extremely high signal-to-noise even under conditions of high relative humidity. Additionally, cavity ring-down IR spectroscopy is used to achieve an extremely high sensitivity to combustion trace gases in this spectral region; ppm level CH 4 is one demonstrated example. The importance of spectral resolution in the sensitivity of a trace-gas measurement is examined by spectral modeling in the mid- and near-IR, and efforts to improve measurement resolution through novel instrument development are described. While previous project reports focused on benefits and complexities of the dual-etalon cavity ring-down infrared spectrometer, here details on steps taken to implement this unique and potentially revolutionary instrument are described. This report also illustrates and critiques the general strategy of IR- laser photodetection of trace gases leading to the conclusion that mid-IR laser spectroscopy techniques provide a promising basis for further instrument development and implementation that will enable cost-effective sensitive detection of multiple key contaminant species simultaneously.

Space station contamination control study: Internal combustion, phase 1

Science.gov (United States)

Ruggeri, Robert T.

1987-01-01

Contamination inside Space Station modules was studied to determine the best methods of controlling contamination. The work was conducted in five tasks that identified existing contamination control requirements, analyzed contamination levels, developed outgassing specification for materials, wrote a contamination control plan, and evaluated current materials of offgassing tests used by NASA. It is concluded that current contamination control methods can be made to function on the Space Station for up to 1000 days, but that current methods are deficient for periods longer than about 1000 days.

Tracey - a simulation model of trace element fluxes in soil-plant system for long-term assessment of a radioactive groundwater contamination

Energy Technology Data Exchange (ETDEWEB)

Gaerdenaes, Annemieke (Dept. of Soil and Environment, Swedish Univ. of Agricultural Sciences, Uppsala (Sweden)); Eckersten, Henrik (Dept. of Ecology and Crop Production, Swedish Univ. of Agricultural Sciences, Uppsala (Sweden)); Reinlert, Andre (Dept. of Physical Geography and Ecosystems Analysis, Lund Univ., Lund (Sweden)); Gustafsson, David; Jansson, Per-Erik (Dept. Land and WaterResources, Royal Inst. of Technology, Stockholm (Sweden)); Ekstroem, Per-Anders; Avila, Rodolfo (Facilia AB, Bromma (Sweden)); Greger, Maria (Dept. of Botany, Stockholm Univ., Stockholm (Sweden))

2009-10-15

We developed a general trace element model called Tracey to simulate dynamically the possible accumulation of radionuclides as a result of an long-term radioactive contamination of groundwater in terrestrial ecosystems. The overall objectives of the study are to: 1) Develop and evaluate a multi-compartmental model that dynamically simulates the transport and accumulation of a radionuclide in the soil-plant system at a time scale relevant for risk assessment of nuclear fuel waste; and 2) Asses the possible accumulation of radionuclide in terrestrial ecosystems due to an eventual long-term continuous radioactive groundwater contamination. Specific objectives were to assess: - The proportion of the contamination accumulated and where it is stored in the ecosystem. - The importance of the plant uptake approach for accumulation of radionuclides. - The most important radionuclide properties and ecosystem characteristics for accumulation and losses. - The proportion of the contamination lost and how is it lost. - The circumstances which stimulated export of radionuclides to other ecosystems. The model presented here, called Tracey, is a stand-alone version to allow for long simulation periods relevant for the time scale of risk assessment of nuclear waste (i.e. several thousand years) with time steps as short as one day. Tracey is a multi-compartmental model in which fluxes and storage of radionuclide are described for different plant parts and for several soil layers. Each layer includes pools of slowly and quickly decomposing litter, humus, solved and absorbed trace element. The trace element fluxes are assumed to be proportional to either water or carbon fluxes, these fluxes are simulated using the dynamic model CoupModel for fluxes of water, carbon, nitrogen and carbon in terrestrial ecosystems. Two different model approaches were used to describe plant uptake of radionuclides. The one called passive uptake approach is driven by water uptake and the one called active

Tracing And Control Of Engineering Requirements

Science.gov (United States)

Turner, Philip R.; Stoller, Richard L.; Neville, Ted; Boyle, Karen A.

1991-01-01

TRACER (Tracing and Control of Engineering Requirements) is data-base/word-processing software system created to document and maintain order of both requirements and descriptions associated with engineering project. Implemented on IBM PC under PC-DOS. Written with CLIPPER.

Spectroscopic Determination of Trace Contaminants in High-Purity Oxygen

Science.gov (United States)

Hornung, Steven

2013-01-01

Oxygen used for extravehicular activities (EVAs) must be free of contaminants because a difference in a few tenths of a percent of argon or nitrogen content can mean significant reduction in available EVA time. These inert gases build up in the extravehicular mobility unit because they are not metabolized or scrubbed from the atmosphere. A prototype optical emission technique capable of detecting argon and nitrogen below 0.1% in oxygen has been developed. This instrument uses a glow discharge in reduced-pressure gas to produce atomic emission from the species present. Because the atomic emission lines from oxygen, nitrogen, and argon are discrete, and in many cases well-separated, trace amounts of argon and nitrogen can be detected in the ultraviolet and visible spectrum. This is a straightforward, direct measurement of the target contaminants, and may lend itself to a device capable of on-orbit verification of oxygen purity. A glow discharge is a plasma formed in a low-pressure (1 to 10 Torr) gas cell between two electrodes. Depending on the configuration, voltages ranging from 200 V and above are required to sustain the discharge. In the discharge region, the gas is ionized and a certain population is in the excited state. Light is produced by the transitions from the excited states formed in the plasma to the ground state. The spectrum consists of discrete, narrow emission lines for the atomic species, and broader peaks that may appear as a manifold for molecular species such as O2 and N2, the wavelengths and intensities of which are a characteristic of each atom. The oxygen emission is dominated by two peaks at 777 and 844 nm.

Variable pattern contamination control under positive pressure

International Nuclear Information System (INIS)

Philippi, H.M.

1997-01-01

Airborne contamination control in nuclear and biological laboratories is traditionally achieved by directing the space ventilation air at subatmospheric pressures in one fixed flow pattern. However, biological and nuclear contamination flow control in the new Biological Research Facility, to be commissioned at the Chalk River Laboratories in 1996, will have the flexibility to institute a number of contamination control patterns, all achieved at positive (above atmospheric) pressures. This flexibility feature, made possible by means of a digitally controlled ventilation system, changes the facility ventilation system from being a relatively rigid building service operated by plant personnel into a flexible building service which can be operated by the facility research personnel. This paper focuses on and describes the application of these unique contamination control features in the design of the new Biological Research Facility. 3 refs., 7 figs

Variable pattern contamination control under positive pressure

Energy Technology Data Exchange (ETDEWEB)

Philippi, H.M. [Chalk River Labs., Ontario (Canada)

1997-08-01

Airborne contamination control in nuclear and biological laboratories is traditionally achieved by directing the space ventilation air at subatmospheric pressures in one fixed flow pattern. However, biological and nuclear contamination flow control in the new Biological Research Facility, to be commissioned at the Chalk River Laboratories in 1996, will have the flexibility to institute a number of contamination control patterns, all achieved at positive (above atmospheric) pressures. This flexibility feature, made possible by means of a digitally controlled ventilation system, changes the facility ventilation system from being a relatively rigid building service operated by plant personnel into a flexible building service which can be operated by the facility research personnel. This paper focuses on and describes the application of these unique contamination control features in the design of the new Biological Research Facility. 3 refs., 7 figs.

Biogeochemical and hydrological controls on fate and distribution of trace metals in oiled Gulf salt marshes

Science.gov (United States)

Keevan, J.; Natter, M.; Lee, M.; Keimowitz, A.; Okeke, B.; Savrda, C.; Saunders, J.

2011-12-01

On April 20, 2010, the drilling rig Deepwater Horizon exploded in the Gulf of Mexico, resulting in the release of approximately 5 million barrels of crude oil into the environment. Oil and its associated trace metals have been demonstrated to have a detrimental effect on coastal wetland ecosystems. Wetlands are particularly susceptible to oil contamination because they are composed largely of fine-grained sediments, which have a high capacity to adsorb organic matter and metals. The biogeochemical cycling of trace metals can be strongly influenced by microbial activity, specifically those of sulfate- and iron-reducing bacteria. Microbial activity may be enhanced by an increase in amounts of organic matter such as oil. This research incorporates an assessment of levels of trace metals and associated biogeochemical changes from ten coastal marshes in Alabama, Mississippi, and Louisiana. These sampling sites range in their pollution levels from pristine to highly contaminated. A total digestion analysis of wetland sediments shows higher concentrations of certain trace metals (e.g., Ni, Cu, Pb, Zn, Sr, Co, V, Ba, Hg, As) in heavily-oiled areas compared to less-affected and pristine sites. Due to chemical complexation among organic compounds and metals, crude oils often contain elevated levels (up to hundreds of mg/kg) of trace metals At the heavily-oiled Louisiana sites (e.g., Bay Jimmy, Bayou Dulac, Bay Batiste), elevated levels of metals and total organic carbon have been found in sediments down to depths of 30 cm. Clearly the contamination is not limited to shallow sediments and oil, along with various associated metals, may be invading into deeper (pre-industrial) portions of the marsh sediments. Pore-waters extracted from contaminated sediments are characterized by very high levels of reduced sulfur (up to 80 mg/kg), in contrast to fairly low ferrous iron concentrations (<0.02 mg/kg). The influx of oil into the wetlands might provide the initial substrate and

Basic radiological studies contamination control experiments

International Nuclear Information System (INIS)

Duce, S.W.; Winberg, M.R.; Freeman, A.L.

1989-09-01

This report describes the results of experiments relating to contamination control performed in support of the Environmental Restoration Programs Retrieval Project. During the years 1950 to 1970 waste contaminated with plutonium and other transuranic radionuclides was disposed of in shallow land-filled pits and trenches at the Idaho National Engineering Laboratory. Due to potential for migration of radionuclides to an existing aquifer the feasibility of retrieving and repackaging the waste for placement in a final repository is being examined as part of a retrieval project. Contamination control experiments were conducted to determine expected respirable and nonrespirable plutonium contaminated dust fractions and the effectiveness of various dust suppression techniques. Three soil types were tested to determine respirable fractions: Rocky Flats Plant generic soil, Radioactive Waste Management Complex generic soil, and a 1:1 blend of the two soil types. Overall, the average respirable fraction of airborne dust was 5.4% by weight. Three contamination control techniques were studied: soil fixative sprays, misting agents, and dust suppression agents. All of the tested agents proved to be effective in reducing dust in the air. Details of product performance and recommended usage are discussed

Potential of Ranunculus acris L. for biomonitoring trace element contamination of riverbank soils: photosystem II activity and phenotypic responses for two soil series.

Science.gov (United States)

Marchand, Lilian; Lamy, Pierre; Bert, Valerie; Quintela-Sabaris, Celestino; Mench, Michel

2016-02-01

Foliar ionome, photosystem II activity, and leaf growth parameters of Ranunculus acris L., a potential biomonitor of trace element (TE) contamination and phytoavailability, were assessed using two riverbank soil series. R. acris was cultivated on two potted soil series obtained by mixing a TE (Cd, Cu, Pb, and Zn)-contaminated technosol with either an uncontaminated sandy riverbank soil (A) or a silty clay one slightly contaminated by TE (B). Trace elements concentrations in the soil-pore water and the leaves, leaf dry weight (DW) yield, total leaf area (TLA), specific leaf area (SLA), and photosystem II activity were measured for both soil series after a 50-day growth period. As soil contamination increased, changes in soluble TE concentrations depended on soil texture. Increase in total soil TE did not affect the leaf DW yield, the TLA, the SLA, and the photosystem II activity of R. acris over the 50-day exposure. The foliar ionome did not reflect the total and soluble TE concentrations in both soil series. Foliar ionome of R. acris was only effective to biomonitor total and soluble soil Na concentrations in both soil series and total and soluble soil Mo concentrations in the soil series B.

Subsurface Contamination Control

Energy Technology Data Exchange (ETDEWEB)

Y. Yuan

2001-12-12

There are two objectives of this report, ''Subsurface Contamination Control''. The first is to provide a technical basis for recommending limiting radioactive contamination levels (LRCL) on the external surfaces of waste packages (WP) for acceptance into the subsurface repository. The second is to provide an evaluation of the magnitude of potential releases from a defective WP and the detectability of the released contents. The technical basis for deriving LRCL has been established in ''Retrieval Equipment and Strategy for Wp on Pallet'' (CRWMS M and O 2000g, 6.3.1). This report updates the derivation by incorporating the latest design information of the subsurface repository for site recommendation. The derived LRCL on the external surface of WPs, therefore, supercede that described in CRWMS M and O 2000g. The derived LRCL represent the average concentrations of contamination on the external surfaces of each WP that must not be exceeded before the WP is to be transported to the subsurface facility for emplacement. The evaluation of potential releases is necessary to control the potential contamination of the subsurface repository and to detect prematurely failed WPs. The detection of failed WPs is required in order to provide reasonable assurance that the integrity of each WP is intact prior to MGR closure. An emplaced WP may become breached due to manufacturing defects or improper weld combined with failure to detect the defect, by corrosion, or by mechanical penetration due to accidents or rockfall conditions. The breached WP may release its gaseous and volatile radionuclide content to the subsurface environment and result in contaminating the subsurface facility. The scope of this analysis is limited to radioactive contaminants resulting from breached WPs during the preclosure period of the subsurface repository. This report: (1) documents a method for deriving LRCL on the external surfaces of WP for acceptance into the

Urban environmental geochemistry of trace metals

International Nuclear Information System (INIS)

Wong, Coby S.C.; Li Xiangdong; Thornton, Iain

2006-01-01

As the world's urban population continues to grow, it becomes increasingly imperative to understand the dynamic interactions between human activities and the urban environment. The development of urban environmental geochemistry has yielded a significant volume of scientific information about geochemical phenomena found uniquely in the urban environment, such as the distribution, dispersion, and geochemical characteristics of some toxic and potentially toxic trace metals. The aim of this paper is to provide an overview of the development of urban environmental geochemistry as a field of scientific study and highlight major transitions during the course of its development from its establishment to the major scientific interests in the field today. An extensive literature review is also conducted of trace metal contamination of the urban terrestrial environment, in particular of urban soils, in which the uniqueness of the urban environment and its influences on trace metal contamination are elaborated. Potential areas of future development in urban environmental geochemistry are identified and discussed. - Urban environmental geochemistry as a scientific discipline provides valuable information on trace metal contamination of the urban environment and its associated health effects

Evaluation of Commercial Off-the-Shelf Sorbents and Catalysts for Control of Ammonia and Carbon Monoxide

Science.gov (United States)

Luna, Bernadette; Somi, George; Winchester, J. Parker; Grose, Jeffrey; Mulloth, Lila; Perry, Jay L.

2013-01-01

Designers of future space vehicles envision simplifying the Atmosphere Revitalization (AR) system by combining the functions of trace contaminant (TC) control and carbon dioxide removal into one swing-bed system. Flow rates and bed sizes of the TC and CO2 systems have historically been very different. There is uncertainty about the ability of trace contaminant sorbents to adsorb adequately in high-flow or short bed length configurations, and to desorb adequately during short vacuum exposures. There is also concern about ambient ammonia levels in the absence of a condensing heat exchanger. In addition, new materials and formulations have become commercially available, formulations never evaluated by NASA for purposes of trace contaminant control. The optimal air revitalization system for future missions may incorporate a swing-bed system for carbon dioxide (CO2) and partial trace contaminant control, with a reduced-size, low-power, targeted trace contaminant system supplying the remaining contaminant removal capability. This paper describes the results of a comparative experimental investigation into materials for trace contaminant control that might be part of such a system. Ammonia sorbents and low temperature carbon monoxide (CO) oxidation catalysts are the foci. The data will be useful to designers of AR systems for future flexible path missions. This is a continuation of work presented in a prior year, with extended test results.

Octanol-solubility of dissolved and particulate trace metals in contaminated rivers: implications for metal reactivity and availability

International Nuclear Information System (INIS)

Turner, Andrew; Mawji, Edward

2005-01-01

The lipid-like, amphiphilic solvent, n-octanol, has been used to determine a hydrophobic fraction of dissolved and particulate trace metals (Al, Cd, Co, Cu, Mn, Ni, Pb, Zn) in contaminated rivers. In a sample from the River Clyde, southwest Scotland, octanol-solubility was detected for all dissolved metals except Co, with conditional octanol-water partition coefficients, D ow , ranging from about 0.2 (Al and Cu) to 1.25 (Pb). In a sample taken from the River Mersey, northwest England, octanol-solubility was detected for dissolved Al and Pb, but only after sample aliquots had been spiked with individual ionic metal standards and equilibrated. Spiking of the River Clyde sample revealed competition among different metals for hydrophobic ligands. Metal displacement from hydrophobic complexes was generally most significant following the addition of ionic Al or Pb, although the addition of either of these metals had little effect on the octanol-solubility of the other. In both river water samples hydrophobic metals were detected on the suspended particles retained by filtration following their extraction in n-octanol. In general, particulate Cu and Zn (up to 40%) were most available, and Al, Co and Pb most resistant ( 3.3 -10 5.3 ml g -1 . The presence of hydrophobic dissolved and particulate metal species has implications for our understanding of the biogeochemical behaviour of metals in aquatic environments. Specifically, such species are predicted to exhibit characteristics of non-polar organic contaminants, including the potential to penetrate the lipid bilayer. Current strategies for assessing the bioavailability and toxicity of dissolved and particulate trace metals in natural waters may, therefore, require revision. - New approaches are presented for fractionating trace metals in natural waters

Diagnostic de contamination des agrosystèmes périurbains de Dakar par les éléments traces métalliques

Directory of Open Access Journals (Sweden)

Hodomihou, NR.

2016-01-01

Full Text Available Diagnosis of periurban Dakar (Senegal agrosystem contamination by trace elements. Description of the subject. Urban and periurban market gardening is widespread in the Dakar area of Senegal. Repeated long-term application of organic matter results in high inputs of trace elements (TE. Objectives. The aim is to assess TE contamination in suburban agrosystems. Method. At four sites, we compared the Cu, Zn, Pb and Cd content in the surface layers and sublayers of plots cultivated over a long period with the content found in adjacent uncultivated plots. Results. The two prevailing soil types (Arenosol and Fluvisol were characterized by significantly different background soil geochemical TE content. In the 0 – 20 and 20 – 40 cm soil layers at the four studied sites, TE content was significantly higher (p < 0.05 in the cultivated plots than in the non-cultivated plots. Arenosols showed a significantly higher (p < 0.05 TE content than Fluvisols. An exception to these results was found in cultivated Arenosols, where Cd, Cu, Zn and Pb contamination was observed. This could be explained by the frequent input into these soils of sewage sludge, poultry droppings, and irrigation with only partially treated wastewater. Cadmium contamination of cultivated Fluvisols was the result of regular natural phosphate inputs, as observed throughout the soil profile. Conclusions. Analysis of soils and organic matters would enable adjustment of the quantities of organic matter applied and could lead to a reduction in TE contamination within these agroecosystems.

30 CFR 57.5005 - Control of exposure to airborne contaminants.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Control of exposure to airborne contaminants... Underground § 57.5005 Control of exposure to airborne contaminants. Control of employee exposure to harmful airborne contaminants shall be, insofar as feasible, by prevention of contamination, removal by exhaust...

Natural and anthropogenic trace metal contamination and load assessment in the Oum Er-Rbia river basin, Morocco

International Nuclear Information System (INIS)

Schone, Selina; Zahry, Fatiha; Matschullat, Jorg; Bounakhla, Moussa

2008-01-01

Due to natural constraints and its fast socio-economic development Morocco is confronted with serious problems both in terms of water quantity and water quality management. In order to counteract the water quality degradation a comprehensive understanding of the geochemical and hydrological functioning as well as the bahavior of inorganic contaminants in large riverine systems under semiarid conditions shall be developed within the scope of this pilot study. Within the scope of a dissertation project Mrs Zahry has already investigated the physical and geochemical characteristics of the oum Er-Rbia river basin in Morocco. Water, sediment and suspended matter samples were analyzed in order to assess the trace metal contamination of the river. Due to the lack of the local geochemical backgrounds levels the results were normalised to common international standards. But because of the spatial and temporal variability of the geochemical background global standards are not appropriate to answer regional and local problems. Following up the work of Mrs Zahry the project shall for the first time ever in Morocco provide local geochemical backgrounds levels of various media in the large-scale Oum ErRbia river basin to establish regional geochemical standards and to assess the watercourse contamination in terms of anthropogenic contributions of trace metals. The research project will be conducted in cooperation between the CNESTEN, Morocco and the Technical University Bergakademie Freiberg in Germany. The project has started of the aquisation of geo-basis data to develop a sampling strategy. All field investigations (sampling, run-off measurements), analytical work and data analysis will be done in direct collaboration with the Moroccan Scientists [fr

State of the art in sample preparation for trace element analysis (M1)

International Nuclear Information System (INIS)

Barnes, R.M.

2002-01-01

Full text: The accelerated capabilities of modern trace element analysis techniques, especially inductively coupled plasma mass spectrometry (ICP-MS), have challenged the sample preparation competence of most laboratories. Exceptional analytical sensitivity, remarkable analysis speed, automated sample presentation, and intelligent sample sequencing of modern spectroscopic instrumentation have lead to demanding requirements for appropriate sample preparation steps needed for ultra trace concentration and speciation measurements. Contamination control, reliable digestion and extraction techniques, presentation of chemical forms, sample matrix management, and intelligent sample processing available today are often inadequate for the most demanding measurements. Some commercial instrumentation provides convenient implementation of well-established contamination control measures, and reagent and container purity are steadily being improved. Direct sample introduction approaches offer alternatives to conventional solution samples, but achieving calibration reliability is difficult. Developing new sample preparation chemistry is especially arduous and rare, yet progress exists in characterizing microwave-assisted reactions. This presentation will describe contemporary targets for modern sample preparation approaches for ultra trace elemental analysis and the likelihood that they can be reasonably achieved. (author)

Tracing and analytical results of the dioxin contamination incident in 2008 originating from the Republic of Ireland.

Science.gov (United States)

Heres, L; Hoogenboom, R; Herbes, R; Traag, W; Urlings, B

2010-12-01

High levels of dioxins (PCDD/Fs) in pork were discovered in France and the Netherlands at the end of 2008. The contamination was rapidly traced back to a feed stock in the Republic of Ireland (RoI). Burning oil, used for the drying of bakery waste, appeared to be contaminated with PCBs. Consequently, very high levels up to 500 pg TEQ g⁻¹ fat were found in pork. The congener pattern clearly pointed to PCB-oil as a source, but the ratio between the non-dioxin-like indicator PCBs (PCBs 28, 52, 101, 138, 152 and 180) and PCDD/Fs was much lower than observed during the Belgian incident, thereby limiting the suitability of indicator PCBs as a marker for the presence of dioxins and dioxin-like PCBs. This paper describes the tracking and tracing of the incident, the public-private cooperation, the surveillance activities and its results. A major lesson to be learned from this incident is the importance of good private food safety systems. In this incident, it was the private surveillance systems that identified the origin of contamination within 10 days after the first signal of increased dioxin levels in a product. On the other hand, retrospective analyses showed that signals were missed that could have led to an earlier detection of the incident and the source. Above all, the incident would not have occurred when food safety assurance systems had been effectively implemented in the involved feed chain. It is discussed that besides primary responsibility for effective private food safety systems, the competent authorities have to supervise whether the food safety procedures are capable of coping with these kinds of complex food safety issues, while private food companies need to implement the law, and public authorities should supervise and enforce them. Finally, it is discussed whether the health risks derived from consumption of the contaminated batches of meat may have been underestimated during the incident due to the unusually high intake of dioxins.

Trace organic chemicals contamination in ground water recharge.

Science.gov (United States)

Díaz-Cruz, M Silvia; Barceló, Damià

2008-06-01

Population growth and unpredictable climate changes will pose high demands on water resources in the future. Even at present, surface water is certainly not enough to cope with the water requirement for agricultural, industrial, recreational and drinking purposes. In this context, the usage of ground water has become essential, therefore, their quality and quantity has to be carefully managed. Regarding quantity, artificial recharge can guarantee a sustainable level of ground water, whilst the strict quality control of the waters intended for recharge will minimize contamination of both the ground water and aquifer area. However, all water resources in the planet are threatened by multiple sources of contamination coming from the extended use of chemicals worldwide. In this respect, the environmental occurrence of organic micropollutants such as pesticides, pharmaceuticals, industrial chemicals and their metabolites has experienced fast growing interest. In this paper an overview of the priority and emerging organic micropollutants in the different source waters used for artificial aquifer recharge purposes and in the recovered water is presented. Besides, some considerations regarding fate and removal of such compounds are also addressed.

Octanol-solubility of dissolved and particulate trace metals in contaminated rivers: implications for metal reactivity and availability

Energy Technology Data Exchange (ETDEWEB)

Turner, Andrew [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)]. E-mail: aturner@plymouth.ac.uk; Mawji, Edward [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)

2005-05-01

The lipid-like, amphiphilic solvent, n-octanol, has been used to determine a hydrophobic fraction of dissolved and particulate trace metals (Al, Cd, Co, Cu, Mn, Ni, Pb, Zn) in contaminated rivers. In a sample from the River Clyde, southwest Scotland, octanol-solubility was detected for all dissolved metals except Co, with conditional octanol-water partition coefficients, D{sub ow}, ranging from about 0.2 (Al and Cu) to 1.25 (Pb). In a sample taken from the River Mersey, northwest England, octanol-solubility was detected for dissolved Al and Pb, but only after sample aliquots had been spiked with individual ionic metal standards and equilibrated. Spiking of the River Clyde sample revealed competition among different metals for hydrophobic ligands. Metal displacement from hydrophobic complexes was generally most significant following the addition of ionic Al or Pb, although the addition of either of these metals had little effect on the octanol-solubility of the other. In both river water samples hydrophobic metals were detected on the suspended particles retained by filtration following their extraction in n-octanol. In general, particulate Cu and Zn (up to 40%) were most available, and Al, Co and Pb most resistant (<1%) to octanol extraction. Distribution coefficients defining the concentration ratio of octanol-soluble particle-bound metal to octanol-soluble dissolved metal were in the range 10{sup 3.3}-10{sup 5.3} ml g{sup -1}. The presence of hydrophobic dissolved and particulate metal species has implications for our understanding of the biogeochemical behaviour of metals in aquatic environments. Specifically, such species are predicted to exhibit characteristics of non-polar organic contaminants, including the potential to penetrate the lipid bilayer. Current strategies for assessing the bioavailability and toxicity of dissolved and particulate trace metals in natural waters may, therefore, require revision. - New approaches are presented for fractionating

Phytotoxicity of trace metals in spiked and field-contaminated soils: Linking soil-extractable metals with toxicity.

Science.gov (United States)

Hamels, Fanny; Malevé, Jasmina; Sonnet, Philippe; Kleja, Dan Berggren; Smolders, Erik

2014-11-01

Soil tests have been widely developed to predict trace metal uptake by plants. The prediction of metal toxicity, however, has rarely been tested. The present study was set up to compare 8 established soil tests for diagnosing phytotoxicity in contaminated soils. Nine soils contaminated with Zn or Cu by metal mining, smelting, or processing were collected. Uncontaminated reference soils with similar soil properties were sampled, and series of increasing contamination were created by mixing each with the corresponding soil. In addition, each reference soil was spiked with either ZnCl2 or CuCl2 at several concentrations. Total metal toxicity to barley seedling growth in the field-contaminated soils was up to 30 times lower than that in corresponding spiked soils. Total metal (aqua regia-soluble) toxicity thresholds of 50% effective concentrations (EC50) varied by factors up to 260 (Zn) or 6 (Cu) among soils. For Zn, variations in EC50 thresholds decreased as aqua regia > 0.43 M HNO3  > 0.05 M ethylenediamine tetraacetic acid (EDTA) > 1 M NH4 NO3  > cobaltihexamine > diffusive gradients in thin films (DGT) > 0.001 M CaCl2 , suggesting that the last extraction is the most robust phytotoxicity index for Zn. The EDTA extraction was the most robust for Cu-contaminated soils. The isotopically exchangeable fraction of the total soil metal in the field-contaminated soils markedly explained the lower toxicity compared with spiked soils. The isotope exchange method can be used to translate soil metal limits derived from soils spiked with metal salts to site-specific soil metal limits. © 2014 SETAC.

Materials contamination control in the microelectronic industry; Controle de la contamination des materiaux dans l`industrie de la micro-electronique

Energy Technology Data Exchange (ETDEWEB)

Tardif, F

1994-12-31

This paper deals with many aspects of the contamination of materials in the microelectronic industry. The contamination`s control of chemicals, process gases, silicon and the survey of the ions free water`s purity are treated. (TEC). 29 figs., 7 tabs.

Geochemical distribution of trace metals and organochlorine contaminants of a lake ontario shoreline marsh

Energy Technology Data Exchange (ETDEWEB)

Glooschenko, W A; Capocianco, J; Coburn, J; Glooschenko, V

1981-02-01

Rattray Marsh, an 8 ha marsh on the Lake Ontario shoreline at Mississauga, Ontario, is an important local habitat for waterfowl and shorebirds during spring and fall migration. A study was conducted to determine the distribution of nutrients (carbon, nitrogen, and phosphorus) and potential trace metal and organochlorine pollutants in the marsh as evidenced by the sedimentary concentrations of these compounds. Generally, copper, zinc, lead, and mercury were higher in concentration in local soils than in Lake Ontario sediments. Metals and organic carbon levels did not correlate, and the metals appeared to be associated with silts and clays. Organochlorine contaminants include p,p1-DDE, p,p1-DDD, p,p1-DDT, alpha-chlordane, PCB, mirex, and HCB.

Environmental Risk of Metal Mining Contaminated River Bank Sediment at Redox-Transitional Zones

Directory of Open Access Journals (Sweden)

Sarah F. L. Lynch

2014-01-01

Full Text Available Diffuse metal pollution from mining impacted sediment is widely recognised as a potential source of contamination to river systems and may significantly hinder the achievement of European Union Water Framework Directive objectives. Redox-transitional zones that form along metal contaminated river banks as a result of flood and drought cycles could cause biogeochemical changes that alter the behaviour of polyvalent metals iron and manganese and anions such as sulphur. Trace metals are often partitioned with iron, manganese and sulphur minerals in mining-contaminated sediment, therefore the dissolution and precipitation of these minerals may influence the mobility of potentially toxic trace metals. Research indicates that freshly precipitated metal oxides and sulphides may be more “reactive” (more adsorbent and prone to dissolution when conditions change than older crystalline forms. Fluctuations at the oxic-anoxic interface brought about through changes in the frequency and duration of flood and drought episodes may therefore influence the reactivity of secondary minerals that form in the sediment and the flux of dissolved trace metal release. UK climate change models predict longer dry periods for some regions, interspersed with higher magnitude flood events. If we are to fully comprehend the future environmental risk these climate change events pose to mining impacted river systems it is recommended that research efforts focus on identifying the primary controls on trace metal release at the oxic-anoxic interface for flood and drought cycles of different duration and frequency. This paper critically reviews the literature regarding biogeochemical processes that occur at different temporal scales during oxic, reducing and dry periods and focuses on how iron and sulphur based minerals may alter in form and reactivity and influence the mobility of trace metal contaminants. It is clear that changes in redox potential can alter the composition

Technology status report: Transuranic contamination control at INEL

International Nuclear Information System (INIS)

Loomis, G.G.

1991-09-01

This report summarizes proposed FY-92 work at the Idaho National Engineering Laboratory (INEL) in the field of contamination control during transuranic waste handling operations. The proposed work is both applied research and demonstration testing. The INEL needs for contamination control applied research and demonstration testing are listed along with a description of past accomplishments. The INEL proposal is compared to other proposals for contamination control work that are under consideration for funding by the Department of Energy. Benefits of this work and impacts of not sponsoring this work are also given. 21 refs

Integrated Control Sytems of Mycotoxin Contamination

Directory of Open Access Journals (Sweden)

Name\tRomsyah

2006-03-01

Full Text Available Contamination of mycotoxins produced by Aspergillus spp., Fusarium spp . and Penicillium s pp . i n agricultural products has been a concern regarding their effect to health and economic impact. Integrated control system should be based on Hazard Analysis and Critical Control Point (HACCP approach involving Good Agricultural Practices (GAP and Good Manufacturing Practices (GMP . Prevention should be carried out through pre harvest, harvest, post harvest, as well as control quality at all stages of production. Pre harvest control is conducted through the selection of resistant varieties, insect control and weeds management mechanically or applying fungicides and herbicides, plant rotation, irrigation and soil management, as well as biological control . Harvesting at the right time using clean equipments from fungal contamination and insect infestation avoids the contamination of mycotoxins . Post harvest control by physical selection, washing and dilution, drying, storage, application of chemicals and binding agents, natural products, nutrients and vitamins, microbiological control, heating and radiation could also minimize mycotoxin in food and feed . Although chemicals can effectively reduce mycotoxin, the use of those on food/feed should be considered the safety . The addition of natural products, nutrition supplements and vitamins suppress the negative effect of mycotoxin on animals . The use of non-toxigenic fungi and other microbes as biological control is the effective and safe methods for food/feed . The implementation of integrated mycotoxin control system by utilizing the HACCP concept would meet the qualified and safe food/feed products .

Environmental radioactive contamination and its control for nuclear power plants

International Nuclear Information System (INIS)

Shi Zhongqi; Qu Jingyuan; Cui Yongli

1998-01-01

The environmental radioactive releases and exposure to human being due to operation of nuclear power plants in the world and in China, environmental contamination and consequences caused by severe nuclear power plant accidents in the history, control of the radioactive contamination in China, and some nuclear laws on the radioactive contamination control established by international organizations and USA etc. are described according to literature investigation and research. Some problems and comments in radioactive contamination control for nuclear power plants in China are presented. Therefore, perfecting laws and regulations and enhancing surveillances on the contamination control are recommended

Genes and quantitative trait loci (QTL) controlling trace element concentrations in perennial grasses grown on phytotoxic soil contaminated with heavy metals

Science.gov (United States)

Perennial grasses cover diverse soils throughout the world, including sites contaminated with heavy metals, producing forages that must be safe for livestock and wildlife. Chromosome regions known as quantitative trait loci (QTLs) controlling forage mineral concentrations were mapped in a populatio...

30 CFR 56.5005 - Control of exposure to airborne contaminants.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Control of exposure to airborne contaminants... Air Quality and Physical Agents Air Quality § 56.5005 Control of exposure to airborne contaminants. Control of employee exposure to harmful airborne contaminants shall be, insofar as feasible, by prevention...

Trace Metals Bioaccumulation Potentials of Three Indigenous ...

African Journals Online (AJOL)

User

grasses as bioaccumulators of trace metals from polluted soils. Seeds of ... transfer factor (TF) showed that Zn was the most bioaccumulated trace metals by all the grasses followed by. Pb, Mn ... was used to de-contaminate copper (Cu) and.

Materials contamination control in the microelectronic industry

International Nuclear Information System (INIS)

Tardif, F.

1993-01-01

This paper deals with many aspects of the contamination of materials in the microelectronic industry. The contamination's control of chemicals, process gases, silicon and the survey of the ions free water's purity are treated. (TEC). 29 figs., 7 tabs

Is there a risk of trace element contamination in herbal preparations? A test study on the lichen Cetraria islandica.

Science.gov (United States)

Giordani, Paolo; Minganti, Vincenzo; Brignole, Daniele; Malaspina, Paola; Cornara, Laura; Drava, Giuliana

2017-08-01

Lichens are a source of unique secondary metabolites, which have been proved to have many biological properties with possible pharmaceutical roles, including e.g. antioxidant, antimicrobial, antifungal or anti-inflammatory activities and to be worth of consideration for potential human use. However, lichens lack cuticolar tissues and are exposed to several atmospheric contaminants, including trace elements. This work aims at exploring the potential toxicity of herbal preparations derived by the lichen Cetraria islandica due to trace element contamination, testing whether different concentrations may be observed, depending on the origin of the raw material. Fourteen samples of C. islandica, as cut dried thalli occurring on the European market, have been bought from different providers. For each sample, the concentrations of As, Cd, Co, Cu, Fe, Mn, Ni, P, Pb, V and Zn were measured on comminuted herbal substance and on the corresponding decoction, using atomic emission spectrometry (ICP-OES). The elemental concentrations in decoctions were significantly lower than those measured in raw materials, dropping down to levels of negligible health concern. Differences observed in raw materials were not observed anymore in the corresponding decoctions. Also, the elemental transfer rate from dried lichen to decoction was extremely element-specific, ranging from 2% for Cu to 95% for Zn. Copyright © 2017 Elsevier Ltd. All rights reserved.

Suspended sediment and sediment-associated contaminants in San Francisco Bay

Science.gov (United States)

Schoellhamer, D.H.; Mumley, T.E.; Leatherbarrow, J.E.

2007-01-01

Water-quality managers desire information on the temporal and spatial variability of contaminant concentrations and the magnitudes of watershed and bed-sediment loads in San Francisco Bay. To help provide this information, the Regional Monitoring Program for Trace Substances in the San Francisco Estuary (RMP) takes advantage of the association of many contaminants with sediment particles by continuously measuring suspended-sediment concentration (SSC), which is an accurate, less costly, and more easily measured surrogate for several trace metals and organic contaminants. Continuous time series of SSC are collected at several sites in the Bay. Although semidiurnal and diurnal tidal fluctuations are present, most of the variability of SSC occurs at fortnightly, monthly, and semiannual tidal time scales. A seasonal cycle of sediment inflow, wind-wave resuspension, and winnowing of fine sediment also is observed. SSC and, thus, sediment-associated contaminants tend to be greater in shallower water, at the landward ends of the Bay, and in several localized estuarine turbidity maxima. Although understanding of sediment transport has improved in the first 10 years of the RMP, determining a simple mass budget of sediment or associated contaminants is confounded by uncertainties regarding sediment flux at boundaries, change in bed-sediment storage, and appropriate modeling techniques. Nevertheless, management of sediment-associated contaminants has improved greatly. Better understanding of sediment and sediment-associated contaminants in the Bay is of great interest to evaluate the value of control actions taken and the need for additional controls. ?? 2007 Elsevier Inc. All rights reserved.

Contamination and ecological risk assessment of toxic trace elements in the Xi River, an urban river of Shenyang city, China.

Science.gov (United States)

Lin, Chunye; He, Mengchang; Liu, Xitao; Guo, Wei; Liu, Shaoqing

2013-05-01

The objectives of this study were to assess the enrichment, contamination, and ecological risk posed by toxic trace elements in the sediments of the Xi River in the industrialized city of Shenyang, China. Surface sediment and sediment core were collected; analyzed for toxic trace elements; and assessed with an index of geoaccumulation (Igeo), enrichment factor (EF) value, potential ecological risk factor (Er), ecological risk index (RI), and probable effect concentration quotient (PECQ). Elemental concentrations (milligram per kilogram) were 8.5-637.9 for As, 6.5-103.9 for Cd, 12.2-21.9 for Co, 90.6-516.0 for Cr, 258.1-1,791.5 for Cu, 2.6-19.0 for Hg, 70.5-174.5 for Ni, 126.9-1,405.8 for Pb, 3.7-260.0 for Sb, 38.4-100.4 for V, and 503-4,929 for Zn. The Igeo, EF, Er, and PECQ indices showed that the contamination of Cd and Hg was more serious than that of As, Cr, Cu, Ni, Pb, Sb, and Zn, whereas the presence of Co and V might be primarily from natural sources. The Igeo index for Cr and Ni might underestimate the degree of contamination, potentially as a result of high concentrations of these elements in the shale. The RI index was higher than 600, indicating a notably high ecological risk of sediment for the river. The average PECQ for As, Cd, Cr, Cu, Hg, Ni, Pb, and Zn ranged from 1.4 to 4.1 for surface sediment and from 5.2 to 9.6 in the sediment cores, indicating a high potential for an adverse biological effect. It was concluded that the sediment in the Xi River was severely contaminated and should be remediated as a hazardous material.

Contamination control research activities for space optics in JAXA RANDD

Science.gov (United States)

Kimoto, Y.

2017-11-01

Contamination control research activities for space optics projects in JAXA R&D are described. More accurate contamination control techniques are requested because of intensified recent science mission requirements. One approach to control the contamination effects is analysis by software. JAXA has been developing a contamination analytical tool "J-SPICE" (Japanese Spacecraft Induced Contamination analysis software) as well as experiment facilities to improve the J-SPICE. A reflection model in J-SPICE has been experimentally verified and outgassing model data has been acquired by a facility. JAXA has developed a facility which could determine the influence of the contamination at a specific wavelength by combining a vacuum chamber with an I-R spectrometer and performed an experiment to inspect the effect of baking. Space material exposure experiment results reveal the actual thickness of the contamination layer in ISS orbit.

The use of sparge curtains for contaminant plume control

International Nuclear Information System (INIS)

Molnaa, B.; Dablow, J.

1994-01-01

Contamination by petroleum hydrocarbons and organic solvents represents a major impact to soil and groundwater. Following recent research and development, several technologies have evolved to treat saturated zone adsorbed- and dissolved-phase contaminants in situ. These technologies include bioremediation and air sparging. Funnel and gate approaches have been developed at the Waterloo Center for Groundwater Research to control contaminant plume migration and treat dissolved-phase contaminants before allowing migration downgradient and off site. The process consists of using low hydraulic conductivity cutoff walls to funnel groundwater flow through gates that contain in situ bioreactors. These systems can maintain hydraulic control and treat dissolved-phase contaminants at the downgradient margins of plumes, while minimizing, or in some cases eliminating, the need for groundwater pumping. Sparge curtains can be applied to treat dissolved-phase contaminants and prevent downgradient, off-site migration of contaminated groundwater

Contamination control engineering design guidelines for the aerospace community

Science.gov (United States)

Tribble, A. C. (Principal Investigator); Boyadjian, B.; Davis, J.; Haffner, J.; McCullough, E.

1996-01-01

Thermal control surfaces, solar arrays, and optical devices may be adversely affected by a small quantity of molecular and/or particulate contamination. What is rarely discussed is how one: (1) quantifies the level of contamination that must be maintained in order for the system to function properly, and (2) enforces contamination control to ensure compliance with requirements. This document is designed to address these specific issues and is intended to serve as a handbook on contamination control for the reader, illustrating process and methodology while providing direction to more detailed references when needed. The effects of molecular contamination on reflecting and transmitting surfaces are examined and quantified in accordance with MIL STD 1246C. The generation, transportation, and deposition of molecular contamination is reviewed and specific examples are worked to illustrate the process a design engineer can use to estimate end of life cleanliness levels required by solar arrays, thermal control surfaces, and optical surfaces. A similar process is used to describe the effect of particulate contamination as related to percent area coverage (PAC) and bi-directional reflectance distribution function (BRDF). Relationships between PAC and surface cleanliness, which include the effects of submicron sized particles, are developed and BRDF is related to specific sensor design parameters such as Point Source Transmittance (PST). The pros and cons of various methods of preventing, monitoring, and cleaning surfaces are examined and discussed.

In situ stabilization of trace metals in a copper-contaminated soil using P-spiked Linz-Donawitz slag.

Science.gov (United States)

Negim, Osama; Mench, Michel; Bes, Clémence; Motelica-Heino, Mikael; Amin, Fouad; Huneau, Frédéric; Le Coustumer, Philippe

2012-03-01

A former wood exploitation revealing high Cu and As concentration of the soils served as a case study for assisted phytoextraction. P-spiked Linz-Donawitz (LD) slag was used as a soil additive to improve physico-chemical soil properties and in situ stabilize Cu and other trace metals in a sandy Cu-contaminated soil (630 mg kg⁻¹ soil). The LD slag was incorporated into the contaminated soil to consist four treatments: 0% (T1), 1% (T2), 2% (T3), and 4% (T4). A similar uncontaminated soil was used as a control (CTRL). After a 1-month reaction period, potted soils were used for a 2-week growth experiment with dwarf beans. Soil pH increased with the incorporation rate of LD slag. Similarly the soil electrical conductivity (EC, in millisiemens per centimetre) is ameliorated. Bean plants grown on the untreated soil (T1) showed a high phytotoxicity. All incorporation rates of LD slag increased the root and shoot dry weight yields compared to the T1. The foliar Ca concentration of beans was enhanced for all LD slag-amended soil, while the foliar Mg, K, and P concentrations were not increased. Foliar Cu, Zn, and Cr concentrations of beans decreased with the LD slag incorporation rate. P-spiked LD slag incorporation into polluted soil allow the bean growth and foliar Ca concentration, but also to reduce foliar Cu concentration below its upper critical value avoiding an excessive soil EC and Zn deficiency. This dual effect can be of interest for soil remediation at larger scale.

Risk assessment of particle dispersion and trace element contamination from mine-waste dumps.

Science.gov (United States)

Romero, Antonio; González, Isabel; Martín, José María; Vázquez, María Auxiliadora; Ortiz, Pilar

2015-04-01

In this study, a model to delimit risk zones influenced by atmospheric particle dispersion from mine-waste dumps is developed to assess their influence on the soil and the population according to the concentration of trace elements in the waste. The model is applied to the Riotinto Mine (in SW Spain), which has a long history of mining and heavy land contamination. The waste materials are separated into three clusters according to the mapping, mineralogy, and geochemical classification using cluster analysis. Two of the clusters are composed of slag, fresh pyrite, and roasted pyrite ashes, which may contain high concentrations of trace elements (e.g., >1 % As or >4 % Pb). The average pollution load index (PLI) calculated for As, Cd, Co, Cu, Pb, Tl, and Zn versus the baseline of the regional soil is 19. The other cluster is primarily composed of sterile rocks and ochreous tailings, and the average PLI is 3. The combination of particle dispersion calculated by a Gaussian model, the PLI, the surface area of each waste and the wind direction is used to develop a risk-assessment model with Geographic Information System GIS software. The zone of high risk can affect the agricultural soil and the population in the study area, particularly if mining activity is restarted in the near future. This model can be applied to spatial planning and environmental protection if the information is complemented with atmospheric particulate matter studies.

Effect of arbuscular mycorrhizal fungi on trace metal uptake by sunflower plants grown on cadmium contaminated soil.

Science.gov (United States)

Hassan, Saad Eldin; Hijri, Mohamed; St-Arnaud, Marc

2013-09-25

Trace metal (TM) pollution of soil is a worldwide problem that threatens the quality of human and environmental health. Phytoremediation using plants and their associated microbes has been increasingly used as a green technology for cleaning up TM-polluted soils. In this study, we investigated the effect of inoculating two arbuscular mycorrhizal fungal isolates, Rhizophagus irregularis and Funneliformis mosseae, on trace metal uptake by sunflower plants grown in soils contaminated with three different Cd concentrations in a greenhouse trial. Root colonization, plant dry mass, and plant tissue cadmium (Cd), zinc (Zn), and copper (Cu) concentrations in roots and shoots were determined after sunflower harvesting. We found that root mycorrhizal colonization rates were not significantly affected by Cd treatments. At low soil Cd concentration, R. irregularis-inoculated plants had significantly higher shoot Cd and Zn concentrations than plants inoculated with F. mosseae and non-inoculated plants. However, at high soil Cd concentrations, F. mosseae-inoculated plants had significantly lower shoot Cd and Zn concentrations and biological concentration factor (BCF) values than plants inoculated with R. irregularis and non-inoculated plants. Cadmium was mainly translocated in shoot tissues of R. irregularis-inoculated plants and sequestered in the rhizosphere of F. mosseae-inoculated plants. The results indicate that these AMF strains mediate different tolerance strategies to alleviate TM toxicity in their host plants and that inoculation with the R. irregularis strain can be used for Cd phytoextraction, whereas this F. mosseae strain can be useful for Cd and Zn phytostabilization of contaminated soil. Copyright © 2013 Elsevier B.V. All rights reserved.

Standard Practice for Preparation of Aerospace Contamination Control Plans

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This practice is intended to assist in the preparation of formal plans for contamination control, especially of aerospace critical surfaces. Requirements may be established at the systems level, either by the customer or the systems integrator, or at the subsystem level. Subsystem requirements may be imposed by the responsible subsystem supplier or they may be flowed down from the systems organization (4.7). The extent of detail and level of cleanliness required can vary with the particular application and type of hardware being built, but all aspects of contamination control must be included in a final plan. Therefore, each of the following elements must be considered for inclusion in a contamination control plan (CCP): 1.1.1 Cleanliness requirements for deliverable hardware addressing particulate, molecular, or biological contaminants or combination thereof. Specify contamination limits and any budget allocations. 1.1.2 Implementation plans to achieve, verify, and maintain the specified cleanliness re...

Biomonitoring of selected freshwater macrophytes to assess lake trace element contamination: a case study of Nal Sarovar Bird Sanctuary, Gujarat, India

Directory of Open Access Journals (Sweden)

Rita N. KUMAR

2006-02-01

Full Text Available A biomonitoring study was carried out at Nal Sarovar Bird Sanctuary, a proposed Ramsar site, Gujarat State, India, to ascertain the degree of trace element contamination. The study focused on assessment of trace element contamination in certain aquatic macrophytes to be used as biomonitors, in comparison with the sediments (abiotic monitor for heavy metal pollution. Good information was provided by analyzing roots, stems and leaves of native aquatic plants (biomonitors represented by eight species: Bergia odorata, Hydrilla verticillata, Ipomoea aquatica, Najas graminea, Nelumbo nucifera, Phragmites karka, Typha angustata and Vellisnaria spiralis, alongwith surface sediments and water, were analyzed for Cd, Co, Cu, Cu, Ni, Pb and Zn contamination. The highest concentrations of the trace elements were measured in Ipomoea aquatica and the lowest in Bergia odorata. Based on the concentration and toxicity status observed in the lake's vegetation, the six metals are arranged in the following decreasing order: Zn > Cu > Ni > Co > Pb > Cd. Compared with the standard, normal and critical toxicity range in plants, the detected values of Cd and Pb falls within normal range, while that of Co, Ni and Cu were within the critical range. However, Zn showed the highest concentration and alarming toxicity levels, which is considered as one of the most hazardous pollutants in Nal Sarovar Bird Sanctuary. Certain aquatic macrophytes species are also proposed as biomonitors for the investigated heavy metal pollutants. Such result was significant in the plant species such as Ipomoea aquatica and Phragmites karka, which are the two most useful species in biomonitoring studies due to their ability to accumulate elements in high concentration in the roots and their availability throughout the year. The results showed the significant difference in accumulation rate of some metals like Zn, Cu and Ni in different plant organs, which showed more accumulation in root than

Quality assessment of trace Cd and Pb contaminants in Thai herbal medicines using ultrasound-assisted digestion prior to flame atomic absorption spectrometry

Directory of Open Access Journals (Sweden)

Watsaka Siriangkhawut

2017-10-01

Full Text Available A simple, efficient, and reliable ultrasound-assisted digestion (UAD procedure was used for sample preparation prior to quantitative determination of trace Cd and Pb contaminants in herbal medicines using flame atomic absorption spectrometry. The parameters influencing UAD such as the solvent system, sample mass, presonication time, sonication time, and digestion temperature were evaluated. The efficiency of the proposed UAD procedure was evaluated by comparing with conventional acid digestion (CAD procedure. Under the optimum conditions, linear calibration graphs in a range of 2–250 μg/L for Cd, and 50–1000 μg/L for Pb were obtained with detection limits of 0.56 μg/L and 10.7 μg/L for Cd and Pb, respectively. The limit of quantification for Cd and Pb were 1.87 μg/L and 40.3 μg/L, respectively. The repeatability for analysis of 10 μg/L for Cd and 100 μg/L for Pb was 2.3% and 2.6%, respectively. The accuracy of the proposed method was evaluated by rice flour certified reference materials. The proposed method was successfully applied for analysis of trace Cd and Pb in samples of various types of medicinal plant and traditional medicine consumed in Thailand. Most herbal medicine samples were not contaminated with Cd or Pb. The contaminant levels for both metals were still lower than the maximum permissible levels of elements in medicinal plant materials and finished herbal products sets by the Ministry of Public Health of Thailand. The exception was the high level of Cd contamination found in two samples of processed medicinal plants.

Dynamic Sampling of Trace Contaminants During the Mission Operations Test of the Deep Space Habitat

Science.gov (United States)

Monje, Oscar; Valling, Simo; Cornish, Jim

2013-01-01

The atmospheric composition inside spacecraft during long duration space missions is dynamic due to changes in the living and working environment of crew members, crew metabolism and payload operations. A portable FTIR gas analyzer was used to monitor the atmospheric composition within the Deep Space Habitat (DSH) during the Mission Operations Test (MOT) conducted at the Johnson Space Center (JSC). The FTIR monitored up to 20 gases in near- real time. The procedures developed for operating the FTIR were successful and data was collected with the FTIR at 5 minute intervals. Not all the 20 gases sampled were detected in all the modules and it was possible to measure dynamic changes in trace contaminant concentrations that were related to crew activities involving exercise and meal preparation.

Implementation guide of internal contamination control

International Nuclear Information System (INIS)

Balter, Henia; Savio, Eduardo; Souto, Beatriz

1994-01-01

A review of current methods of contamination control for radioisotopes 131I, 125I and 99mTc, periodic control of personnel exposed to radiation.Maximum permissible body burden (Mpbb) for each radionuclide,radiotoxicity as danger of internal contamination directly related with Let, type of radiation,Ali values for various radionuclides and external irradiation as an opposed factor.Effective half life,examples, 99mTc in urine,iodine in thyroid caption, 99m Tc absorption by skin and mouth. Procedure of control and calculation by measurement of urine samples in a gamma spectrometer. Iodine thyroid caption by monitoring of thyroid with a solid NaI(TI)scintillator taking as background radiation the activity of upper leg muscle. Standard solutions are prepared to fill a thyroid phantoms.Results must not be higher than Mpbb of corresponding radionuclide.Bibliography

Contamination control using portable glove bags and containments

International Nuclear Information System (INIS)

Fink, C.

1994-01-01

Portable gloveboxes and containments have been used in the Navy Nuclear Power programs for many years. Their primary application has been to allow maintenance access to radioactive piping systems while limiting the spread of contamination to the immediate environment. The applications have spread to other areas of the nuclear industry and to other industries with similar contamination control problems. The general application is to keep the contaminants in, but other uses keep the contamination out. The devices can best be classified by material types and construction. They range from the relatively inexpensive polyethylene glove bags for asbestos removal to the semi-permanent aluminum and lexan hard-sided containment structures. There are free-standing open-quotes tentclose quotes structures, support ring devices and tube or bag designs. Only the cost seems to limit the size of these items. The key to the effective use of these devices lies in the planning and control of their application. Proper training of maintenance personnel will greatly facilitate their use, since the main objection seems to be in the exposure received during the rigging of these containments. When all of these considerations are accounted for, a program of contamination control can be quite successful. A brief description of the set-up and use of a specific application is described

Trace Elements in Marine Sediment and Organisms in the Gulf of Thailand

Science.gov (United States)

Worakhunpiset, Suwalee

2018-01-01

This review summarizes the findings from studies of trace element levels in marine sediment and organisms in the Gulf of Thailand. Spatial and temporal variations in trace element concentrations were observed. Although trace element contamination levels were low, the increased urbanization and agricultural and industrial activities may adversely affect ecosystems and human health. The periodic monitoring of marine environments is recommended in order to minimize human health risks from the consumption of contaminated marine organisms. PMID:29677146

Development of irradiation technique on controlling food contamination residue

International Nuclear Information System (INIS)

Liu Bin; Xiong Shanbai; Xiong Guangquan; Cheng Wei; Chen Yuxia; Liao Tao; Li Xin; Lin Ruotai

2010-01-01

The current state of the researches of irradiation technology on controlling food mycotoxin, pesticide, veterinary drugs and fishery drugs residue was summarized. And the degradation rate, mechanism, products and toxicities of food contamination were expatiated. The free radical from irradiation attack the site of weaker bond, and the less or more toxic substances were produced, which lead to the degradation of the food contamination. The limitations and future application of irradiation technique on controlling food contamination were also analyzed. (authors)

Trace impurity analyzer

International Nuclear Information System (INIS)

Schneider, W.J.; Edwards, D. Jr.

1979-01-01

The desirability for long-term reliability of large scale helium refrigerator systems used on superconducting accelerator magnets has necessitated detection of impurities to levels of a few ppM. An analyzer that measures trace impurity levels of condensable contaminants in concentrations of less than a ppM in 15 atm of He is described. The instrument makes use of the desorption temperature at an indicated pressure of the various impurities to determine the type of contaminant. The pressure rise at that temperature yields a measure of the contaminant level of the impurity. A LN 2 cryogenic charcoal trap is also employed to measure air impurities (nitrogen and oxygen) to obtain the full range of contaminant possibilities. The results of this detector which will be in use on the research and development helium refrigerator of the ISABELLE First-Cell is described

Trace Contaminant Control: An In-Depth Study of a Silica-Titania Composite for Photocatalytic Remediation of Closed-Environment Habitat Air

Science.gov (United States)

Coutts, Janelle L.

2013-01-01

This collection of studies focuses on a PCO system for the oxidation of a model compound, ethanol, using an adsorption-enhanced silica-TiO2 composite (STC) as the photocatalyst; studies are aimed at addressing the optimization of various parameters including light source, humidity, temperature, and possible poisoning events for use as part of a system for gaseous trace-contaminant control system in closed-environment habitats. The first goal focused on distinguishing the effect of photon flux (i.e., photons per unit time reaching a surface) from that of photon energy (i.e., wavelength) of a photon source on the PCO of ethanol. Experiments were conducted in a bench-scale annular reactor packed with STC pellets and irradiated with either a UV-A fluorescent black light blue lamp O max=365 nm) at its maximum light intensity or a UV-C germicidal lamp O. max=254 nm) at three levels of light intensity. The STC-catalyzed oxidation of ethanol was found to follow zero-order kinetics with respect to CO2 production, regardless of the photon source. Increased photon flux led to increased EtOH removal, mineralization, and oxidation rate accompanied by lower intermediate concentration in the effluent. The oxidation rate was higher in the reactor irradiated by UV-C than by UV-A (38.4 vs. 31.9 nM s-1 ) at the same photon flux, with similar trends for mineralization (53.9 vs. 43.4%) and reaction quantum efficiency (i.e., photonic efficiency, 63.3 vs. 50.1 nmol C02 mol photons-1 ). UV-C irradiation also led to decreased intermediate concentration in the effluent compared to UV -A irradiation. These results demonstrated that STC-catalyzed oxidation is enhanced by both increased photon flux and photon energy. The effect of temperature and relative humidity on the STC-catalyzed degradation of ethanol was also determined using the UV-A light source at its maximum intensity.

Tracing contaminant pathways in sandy heterogeneous glaciofluvial sediments using a sedimentary depositional model

International Nuclear Information System (INIS)

Webb, E.K.; Anderson, M.P.

1990-01-01

Heterogeneous sedimentary deposits present complications for tracking contaminant movement by causing a complex advective flow field. Connected areas of high conductivity produce so-called fast paths that control movement of solutes. Identifying potential fast paths and describing the variation in hydraulic properties was attempted through simulating the deposition of a glaciofluvial deposit (outwash). Glaciofluvial deposits usually consist of several depositional facies, each of which has different physical characteristics, depositional structures and hydraulic properties. Therefore, it is unlikely that the property of stationarity (a constant mean hydraulic conductivity and a mono-modal probability distribution) holds for an entire glaciofluvial sequence. However, the process of dividing an outwash sequence into geologic facies presumably identifies units of material with similar physical characteristics. It is proposed that patterns of geologic facies determined by field observation can be quantified by mathematical simulation of sediment deposition. Subsequently, the simulated sediment distributions can be used to define the distribution of hydrogeologic parameters and locate possible fast paths. To test this hypothesis, a hypothetical glacial outwash deposit based on geologic facies descriptions contained in the literature was simulated using a sedimentary depositional model, SEDSIM, to produce a three-dimensional description of sediment grain size distributions. Grain size distributions were then used to estimate the spatial distribution of hydraulic conductivity. Subsequently a finite-difference flow model and linked particle tracking algorithm were used to trace conservative transport pathways. This represents a first step in describing the spatial heterogeneity of hydrogeologic characteristics for glaciofluvial and other braided stream environments. (Author) (39 refs., 7 figs.)

Assessment of suitability of tree species for the production of biomass on trace element contaminated soils

International Nuclear Information System (INIS)

Evangelou, Michael W.H.; Deram, Annabelle; Gogos, Alexander; Studer, Björn; Schulin, Rainer

2012-01-01

Highlights: ► Birch: lowest metal concentrations in foliage, wood and bark. ► Bark proportion does not have to decline with increasing age of tree. ► Long harvest rotation (>25 y) reduces metal concentrations in stem. ► Birch: most suitable tree for BCL. - Abstract: To alleviate the demand on fertile agricultural land for production of bioenergy, we investigated the possibility of producing biomass for bioenergy on trace element (TE) contaminated land. Soil samples and plant tissues (leaves, wood and bark) of adult willow (Salix sp.), poplar (Populus sp.), and birch (Betula pendula) trees were collected from five contaminated sites in France and Germany and analysed for Zn, Cd, Pb, Cu, Ca, and K. Cadmium concentration in tree leaves were correlated with tree species, whereas Zn concentration in leaves was site correlated. Birch revealed significantly lower leaf Cd concentrations (1.2–8.9 mg kg −1 ) than willow and poplar (5–80 mg kg −1 ), thus posing the lowest risk for TE contamination of surrounding areas. Birch displayed the lowest bark concentrations for Ca (2300–6200 mg kg −1 ) and K (320–1250 mg kg −1 ), indicating that it would be the most suitable tree species for fuel production, as high concentrations of K and Ca decrease the ash melting point which results in a reduced plant lifetime. Due to higher TE concentrations in bark compared to wood a small bark proportion in relation to the trunk is desirable. In general the bark proportion was reduced with the tree age. In summary, birch was amongst the investigated species the most suitable for biomass production on TE contaminated land.

Present and Future Challenges in Trace and Ultra-Trace Analysis

International Nuclear Information System (INIS)

Toulhoat, P.

2005-01-01

The analysis of trace and ultra-trace elements is continuously stimulating the progress in analytical chemistry. Environmental chemistry, radiochemistry, biology, health, agri-food are prescribers of trace analyses, with continuously increasing exigencies: lowering detection limits, lowering costs and analysis time, improving the quality of analytical information. Precise data about the chemical identity and chemical environment of analytes are now requested. Such pieces of information, beyond simple numerical data and confidence intervals, are necessary to understand studied systems, and to predict their evolution. From environmental contamination cases, one can envisage the various aspects of a problem, with for each of them its own exigencies and specificities in terms of analytical methods and approaches. The detection of traces and ultra-traces of actinides and fission products has been recently revisited and stimulates new technological developments (non proliferation issues, waste management). Data on their speciation in geological and biological media are essential for evaluating the safety of nuclear waste repositories. Various techniques are now used to determine speciation in liquid samples or on surfaces, with tremendous spatial resolutions or sensitivities. A new revolution in analytical chemistry is expected with the development of micro- or nano-analytical technologies. (author)

Forensic Luminol Blood Test for Preventing Cross-contamination in Dentistry: An Evaluation of a Dental School Clinic.

Science.gov (United States)

Bortoluzzi, Marcelo Carlos; Cadore, Peterson; Gallon, Andrea; Imanishi, Soraia Almeida Watanabe

2014-10-01

More than 200 different diseases may be transmitted from exposure to blood in the dental setting. The aim of this study is to identify possible faults in the crosscontamination chain control in a dental school clinic searching for traces of blood in the clinical contact surfaces (CCS) through forensic luminol blood test. Traces of invisible blood where randomly searched in CCS of one dental school clinic. Forty eight surfaces areas in the CCS were tested and the presence of invisible and remnant blood was identified in 28 (58.3%) items. We suggest that the luminol method is suitable for identifying contamination with invisible blood traces and this method may be a useful tool to prevent cross-contamination in the dental care setting.

Contamination control training for biomedical facilities

International Nuclear Information System (INIS)

Trinoskey, P.A.

1994-10-01

In 1991, a contamination control course was developed for the Biology and Biotechnology Research Program (BBRP) at the Lawrence Livermore National Laboratory (LLNL). This course was based on the developer's experience in Radiation Safety at the University of Utah and University of Kansas Medical Center. This course has been well received at LLNL because it addresses issues that are important to individuals handling small quantities of radioactive materials. This group of users is often overlooked. They are typically very well educated and are expected to ''know'' what they should do. Many of these individuals are not initially comfortable working with radioactive materials. They appreciate the opportunity to be introduced to contamination control techniques and to discuss issues they may have. In addition, the authors benefit by experience that researchers bring from other facilities. The training course will address the specific radiological training requirements for chemists, biologists, and medical researchers who are using small amounts of dispersible radionuclides in tabletop experiments, and will not be exposed to other radiation sources. The training will include: the potential hazards of typical radionuclides, contamination control procedures, and guidance for developing and including site-specific information. The training course will eliminate the need for Radiological Worker II training for bio-medical researchers. The target audience for this training course is bio-medical researchers

Isotopic Tracing of Thallium Contamination in Soils Affected by Emissions from Coal-Fired Power Plants.

Science.gov (United States)

Vaněk, Aleš; Grösslová, Zuzana; Mihaljevič, Martin; Trubač, Jakub; Ettler, Vojtěch; Teper, Leslaw; Cabala, Jerzy; Rohovec, Jan; Zádorová, Tereza; Penížek, Vít; Pavlů, Lenka; Holubík, Ondřej; Němeček, Karel; Houška, Jakub; Drábek, Ondřej; Ash, Christopher

2016-09-20

Here, for the first time, we report the thallium (Tl) isotope record in moderately contaminated soils with contrasting land management (forest and meadow soils), which have been affected by emissions from coal-fired power plants. Our findings clearly demonstrate that Tl of anthropogenic (high-temperature) origin with light isotope composition was deposited onto the studied soils, where heavier Tl (ε(205)Tl ∼ -1) naturally occurs. The results show a positive linear relationship (R(2) = 0.71) between 1/Tl and the isotope record, as determined for all the soils and bedrocks, also indicative of binary Tl mixing between two dominant reservoirs. We also identified significant Tl isotope variations within the products from coal combustion and thermo-desorption experiments with local Tl-rich coal pyrite. Bottom ash exhibited the heaviest Tl isotope composition (ε(205)Tl ∼ 0), followed by fly ash (ε(205)Tl between -2.5 and -2.8) and volatile Tl fractions (ε(205)Tl between -6.2 and -10.3), suggesting partial Tl isotope fractionations. Despite the evident role of soil processes in the isotope redistributions, we demonstrate that Tl contamination can be traced in soils and propose that the isotope data represent a possible tool to aid our understanding of postdepositional Tl dynamics in surface environments for the future.

Assurance and control of quality in trace element analysis

International Nuclear Information System (INIS)

Heinonen, J.

1979-01-01

The study demonstrates in practice the assurance and control of the quality of results from trace analysis in biological materials. The performance of three analytical methods is studied: one involving the determination of Cs and two the determination of As by neutron activation techniques in biological materials at the natural background level. In the case of Cs, the validity of the analytical procedure was investigated by the means available in the laboratory of the Institute and by utilizing the specific properties of the determinant. In the establishment and control of accuracy, the analysis of precision was essential. The investigation of the two different methods applied for the determination of arsenic demonstrates the many problems connected with trace analysis. For the control of accuracy a number of different kinds of reference materials (RMs) were used, namely four former intercomparison materials of the IAEA and two certified RMs of the NBS. The various tests performed revealed two different types of systematic errors. The scheme applied for the long-term surveillance of systematic and random errors is found to be suitable for the continuous control of quality of results from routine analysis. (author)

Atom trap trace analysis

International Nuclear Information System (INIS)

Lu, Z.-T.; Bailey, K.; Chen, C.-Y.; Du, X.; Li, Y.-M.; O'Connor, T. P.; Young, L.

2000-01-01

A new method of ultrasensitive trace-isotope analysis has been developed based upon the technique of laser manipulation of neutral atoms. It has been used to count individual 85 Kr and 81 Kr atoms present in a natural krypton sample with isotopic abundances in the range of 10 -11 and 10 -13 , respectively. The atom counts are free of contamination from other isotopes, elements,or molecules. The method is applicable to other trace-isotopes that can be efficiently captured with a magneto-optical trap, and has a broad range of potential applications

Comparison of trace element contamination levels (Cu, Zn, Fe, Cd ...

African Journals Online (AJOL)

SERVER

2008-03-18

Mar 18, 2008 ... Chemical analysis of the trace elements in the soft tissues. The trace elements of interest (Cu, Zn, Fe, Pb, Cd) were then determined in the digested solutions, using Thermoelemental type. M6 brand of an atomic absorption Spectrometer equipped with a flame operated atomisation system and a deuterium ...

Subtask 4.8 - Fate and Control of Mercury and Trace Elements

Energy Technology Data Exchange (ETDEWEB)

Pavlish, John; Lentz, Nicholas; Martin, Christopher; Ralston, Nicholas; Zhuang, Ye; Hamre, Lucinda

2011-12-31

The Center for Air Toxic Metals® (CATM®) Program at the Energy & Environmental Research Center (EERC) continues to focus on vital basic and applied research related to the fate, behavior, measurement, and control of trace metals, especially mercury, and the impact that these trace metals have on human health and the environment. For years, the CATM Program has maintained an international perspective, performing research and providing results that apply to both domestic and international audiences, with reports distributed in the United States and abroad. In addition to trace metals, CATM’s research focuses on other related emissions and issues that impact trace metal releases to the environment, such as SO_x, NO_x, CO₂, ash, and wastewater streams. Of paramount interest and focus has been performing research that continues to enable the power and industrial sectors to operate in an environmentally responsible manner to meet regulatory standards. The research funded by the U.S. Department of Energy’s (DOE’s) National Energy Technology Laboratory (NETL) through CATM has allowed significant strides to be made to gain a better understanding of trace metals and other emissions, improve sampling and measurement techniques, fill data gaps, address emerging technical issues, and develop/test control technologies that allow industry to cost-effectively meet regulatory standards. The DOE NETL–CATM research specifically focused on the fate and control of mercury and trace elements in power systems that use CO₂ control technologies, such as oxycombustion and gasification systems, which are expected to be among those technologies that will be used to address climate change issues. In addition, research addressed data gaps for systems that use conventional and multipollutant control technologies, such as electrostatic precipitators, selective catalytic reduction units, flue gas desulfurization systems, and flue gas

DNA-tagged Microparticles for Tracing Water Flows and Travel Times in Natural Systems: The First results from Controlled Laboratory Experiments

Science.gov (United States)

Bogaard, T.; Bandyopadhyay, S.; Foppen, J. W.

2017-12-01

Societal demand for water safety is continuously increasing, being it resilient against flood/droughts, clean water for ecosystems, recreation or safe drinking water. Robust methods to measure temporal and spatial patterns of water and contaminant pathways are still lacking. Our research project aims to develop and apply (1) innovative, robust, and environmental-friendly silica-protected iron oxide micro-particles tagged with artificial DNA to trace contaminant movement and travel times of water in natural systems and (2) an innovative coupled model approach to capture dynamics in hydrological pathways and their effects on water quality. The exceptional property of DNA-tagging is the infinite number of unique tracers that can be produced and their detectability at extreme low concentrations. The advantage of the iron-core of the particle is the magnetic harvesting of the particles from water-samples. Such tracers are thought to give the water sector a unique tool for in-situ mapping of transport of contaminants and pathogenic microorganisms in water systems. However, the characteristics of the particle like magnetic property of the iron-core and surface potential of the silica layer, are of key importance for the behaviour of the particle in surface water and in soils. Furthermore, the application of such micro-particles requires strict protocols for the experiment, sampling and laboratory handling which are currently not available. We used two different types of silica-protected DNA-tagged micro-particles. We performed batch, column and flow experiments to assess the behaviour of the particles. We will present the first results of the controlled laboratory experiments for hydrological tracing. We will discuss the results and link it to the differences in particles design. Furthermore, we will draw conclusions and discuss knowledge gaps for future application of silica-protected DNA-tagged micro-particles in hydrological research.

Outbreak of hepatitis A in a college traced to contaminated water reservoir in cafeteria.

Science.gov (United States)

Poonawagul, U; Warintrawat, S; Snitbhan, R; Kitisriwarapoj, S; Chaiyakunt, V; Foy, H M

1995-12-01

A sharp but short outbreak of hepatitis A occurred in a college during September and October 1992. The epidemic pattern suggested a common source. The attack rate of clinically recognizable hepatitis A was 8% all cases were HAV IgM positive. Among 31 students with minor symptoms but without jaundice 8 (26%) were also HAV IgM positive, as were 8 (10%) of 77 totally asymptomatic students tested. A case control study of eating and drinking habits of the students showed no other significant differences other than that 45 of 56 cases and 18 of 34 controls interviewed had filled their water glasses by dipping them in a overflow water reservoir. This gives an odds ratio of 3.8. The reservoir was heavily contaminated with coliform bacteria and the residual chlorine was at lower than standard concentration, whereas other water resources were clean. It is suggested that the reservoir had been contaminated with hepatitis A virus by somebody with fecally contaminated hands a couple of weeks prior to the beginning of the outbreak.

Sorbent control of trace metals in sewage sludge combustion and incineration

Science.gov (United States)

Naruse, I.; Yao, H.; Mkilaha, I. S. N.

2003-05-01

Coal and wastes combustion have become an important issue not only in terms of energy generation but also environmental conservation. The need for alternative fuels and wastes management has made the two energy sources of importance. However, the utilization of the two is faced with problems of impurity trace metals in the fuel. These metals usually speciate during combustion or incineration leading to generation of fumes and subsequently particles. This paper reports on the study aimed at understanding the speciation of trace metals and their emission from combustion systems as particulates. Experiments carried out using a down-flow furnace and theoretical study carried out using lead, chromium and cadmium as basic metals had shown that their speciation and subsequent emission is controlled by both chemical composition and physical properties of the fuel. The physical and chemical and physical properties of the fuel and their respective compounds and the operating conditions of the incineration and combustion system control the enrichment of the particles with trace metals.

Ground-water contamination and legal controls in Michigan

Science.gov (United States)

Deutsch, Morris

1963-01-01

The great importance of the fresh ground-water resources of Michigan is evident because 90 percent of the rural and about 70 percent of the total population of the State exclusive of the Detroit metropolitan area are supplied from underground sources. The water-supply and public-health problems that have been caused by some cases of ground-water contamination in the State illustrate the necessity of protecting this vital resource.Manmade and natural contaminants, including many types of chemical and organic matter, have entered many of the numerous aquifers of the State. Aquifers have been contaminated by waste-laden liquids percolating from the surface or from the zone of aeration and by direct injection to the aquifer itself. Industrial and domestic wastes, septic tanks, leaking sewers, flood waters or other poor quality surface waters, mine waters, solids stored or spread at the surface, and even airborne wastes all have been sources of ground-water contamination in Michigan. In addition, naturally occurring saline waters have been induced into other aquifers by overpumping or unrestricted flow from artesian wells, possibly by dewatering operations, and by the deepening of surface stream channels. Vertical migration of saline waters through open holes from formations underlying various important aquifers also has spoiled some of the fresh ground waters in the State. In spite of the contamination that has occurred, however, the total amount of ground water that has been spoiled is only a small part of the total resource. Neither is the contamination so widespread as that of the surface streams of Michigan.Overall legal authority to control most types of ground-water contamination in the State has been assigned by the Michigan Legislature to the Water Resources Commission, although the Department of Conservation and the Health Department also exercise important water-pollution control functions. The Michigan Supreme Court, in an important case upholding the power

Analysis of food contaminants

National Research Council Canada - National Science Library

Gilbert, John

1984-01-01

... quantification methods used in the analysis of mycotoxins in foods - Confirmation and quantification of trace organic food contaminants by mass spectrometry-selected ion monitoring - Chemiluminescence...

Bag-like contaminant control work module

International Nuclear Information System (INIS)

Buchanan, H.; Jacobson, E.B.

1982-01-01

A bag-like contaminant control work module is formed from a flexible impervious membrane which is inflated inside of an enclosed workspace to protect workers in the module from contaminants. The workspace, such as in a nuclear power steam generator, has a portal or manway opening into the workspace into which the module is secured by a module passageway. The module includes one or more glove boxes, in which the workers perform their assigned tasks after passing through the passageway and portal. The module includes one or more absolute filters allowing passage of air flow through the module passageway and into the workspace only through the filters. The module may include an auxiliary passageway secured to the outside of the module passageway and also secured in the portal opening and through which items can be passed back and forth to the worker in the glove box from outside the portal. The module is invertible so that it can be pulled out of the workspace trapping all the contaminants therein and disposed of without handling the contaminants

Integrated Control Sytems of Mycotoxin Contamination

OpenAIRE

Name Romsyah

2006-01-01

Contamination of mycotoxins produced by Aspergillus spp., Fusarium spp . and Penicillium s pp . i n agricultural products has been a concern regarding their effect to health and economic impact. Integrated control system should be based on Hazard Analysis and Critical Control Point (HACCP) approach involving Good Agricultural Practices (GAP) and Good Manufacturing Practices (GMP) . Prevention should be carried out through pre harvest, harvest, post harvest, as well as control quality at all s...

Analytical techniques and quality control in biomedical trace element research

DEFF Research Database (Denmark)

Heydorn, K.

1994-01-01

The small number of analytical results in trace element research calls for special methods of quality control. It is shown that when the analytical methods are in statistical control, only small numbers of duplicate or replicate results are needed to ascertain the absence of systematic errors....../kg. Measurement compatibility is obtained by control of traceability to certified reference materials, (C) 1994 Wiley-Liss, Inc....

Octanol-solubility of dissolved and particulate trace metals in contaminated rivers: implications for metal reactivity and availability.

Science.gov (United States)

Turner, Andrew; Mawji, Edward

2005-05-01

The lipid-like, amphiphilic solvent, n-octanol, has been used to determine a hydrophobic fraction of dissolved and particulate trace metals (Al, Cd, Co, Cu, Mn, Ni, Pb, Zn) in contaminated rivers. In a sample from the River Clyde, southwest Scotland, octanol-solubility was detected for all dissolved metals except Co, with conditional octanol-water partition coefficients, D(ow), ranging from about 0.2 (Al and Cu) to 1.25 (Pb). In a sample taken from the River Mersey, northwest England, octanol-solubility was detected for dissolved Al and Pb, but only after sample aliquots had been spiked with individual ionic metal standards and equilibrated. Spiking of the River Clyde sample revealed competition among different metals for hydrophobic ligands. Metal displacement from hydrophobic complexes was generally most significant following the addition of ionic Al or Pb, although the addition of either of these metals had little effect on the octanol-solubility of the other. In both river water samples hydrophobic metals were detected on the suspended particles retained by filtration following their extraction in n-octanol. In general, particulate Cu and Zn (up to 40%) were most available, and Al, Co and Pb most resistant (octanol extraction. Distribution coefficients defining the concentration ratio of octanol-soluble particle-bound metal to octanol-soluble dissolved metal were in the range 10(3.3)-10(5.3)mlg(-1). The presence of hydrophobic dissolved and particulate metal species has implications for our understanding of the biogeochemical behaviour of metals in aquatic environments. Specifically, such species are predicted to exhibit characteristics of non-polar organic contaminants, including the potential to penetrate the lipid bilayer. Current strategies for assessing the bioavailability and toxicity of dissolved and particulate trace metals in natural waters may, therefore, require revision.

External Contamination Control of Attached Payloads on the International Space Station

Science.gov (United States)

Soares, Carlos E.; Mikatarian, Ronald R.; Olsen, Randy L.; Huang, Alvin Y.; Steagall, Courtney A.; Schmidl, William D.; Wright, Bruce D.; Koontz, Steven

2012-01-01

The International Space Station (ISS) is an on-orbit platform for science utilization in low Earth orbit with multiple sites for external payloads with exposure to the natural and induced environments. Contamination is one of the induced environments that can impact performance, mission success and science utilization on the vehicle. This paper describes the external contamination control requirements and integration process for externally mounted payloads on the ISS. The external contamination control requirements are summarized and a description of the integration and verification process is detailed to guide payload developers in the certification process of attached payloads on the vehicle. A description of the required data certification deliverables covers the characterization of contamination sources. Such characterization includes identification, usage and operational data for each class of contamination source. Classes of external contamination sources covered are vacuum exposed materials, sources of leakage, vacuum venting and thrusters. ISS system level analyses are conducted by the ISS Space Environments Team to certify compliance with external contamination control requirements. This paper also addresses the ISS induced contamination environment at attached payload sites, both at the requirements level as well as measurements made on ISS.

Reactive Distillation and Air Stripping Processes for Water Recycling and Trace Contaminant Control

Science.gov (United States)

Boul, Peter J.; Lange, Kevin E.; Conger, Bruce; Anderson, Molly

2009-01-01

Reactive distillation designs are considered to reduce the presence of volatile organic compounds in the purified water. Reactive distillation integrates a reactor with a distillation column. A review of the literature in this field has revealed a variety of functional reactive columns in industry. Wastewater may be purified by a combination of a reactor and a distiller (e.g., the EWRS or VPCAR concepts) or, in principle, through a design which integrates the reactor with the distiller. A review of the literature in reactive distillation has identified some different designs in such combinations of reactor and distiller. An evaluation of reactive distillation and reactive air stripping is presented with regards to the reduction of volatile organic compounds in the contaminated water and air. Among the methods presented, an architecture is presented for the evaluation of the simultaneous oxidation of organics in air and water. These and other designs are presented in light of potential improvements in power consumptions and air and water purities for architectures which include catalytic activity integrated into the water processor. In particular, catalytic oxidation of organics may be useful as a tool to remove contaminants that more traditional distillation and/or air stripping columns may not remove. A review of the current leading edge at the commercial level and at the research frontier in catalytically active materials is presented. Themes and directions from the engineering developments in catalyst design are presented conceptually in light of developments in the nanoscale chemistry of a variety of catalyst materials.

TRACER - TRACING AND CONTROL OF ENGINEERING REQUIREMENTS

Science.gov (United States)

Turner, P. R.

1994-01-01

TRACER (Tracing and Control of Engineering Requirements) is a database/word processing system created to document and maintain the order of both requirements and descriptive material associated with an engineering project. A set of hierarchical documents are normally generated for a project whereby the requirements of the higher level documents levy requirements on the same level or lower level documents. Traditionally, the requirements are handled almost entirely by manual paper methods. The problem with a typical paper system, however, is that requirements written and changed continuously in different areas lead to misunderstandings and noncompliance. The purpose of TRACER is to automate the capture, tracing, reviewing, and managing of requirements for an engineering project. The engineering project still requires communications, negotiations, interactions, and iterations among people and organizations, but TRACER promotes succinct and precise identification and treatment of real requirements separate from the descriptive prose in a document. TRACER permits the documentation of an engineering project's requirements and progress in a logical, controllable, traceable manner. TRACER's attributes include the presentation of current requirements and status from any linked computer terminal and the ability to differentiate headers and descriptive material from the requirements. Related requirements can be linked and traced. The program also enables portions of documents to be printed, individual approval and release of requirements, and the tracing of requirements down into the equipment specification. Requirement "links" can be made "pending" and invisible to others until the pending link is made "binding". Individuals affected by linked requirements can be notified of significant changes with acknowledgement of the changes required. An unlimited number of documents can be created for a project and an ASCII import feature permits existing documents to be incorporated

Controlling optics contamination at the PolLux STXM

Science.gov (United States)

Watts, B.; Pilet, N.; Sarafimov, B.; Witte, K.; Raabe, J.

2018-04-01

Contamination of X-ray mirror surfaces by carbon is a common issue that can significantly degrade the optical performance of the instrument. The effects can be severe at photon energies near the carbon K-edge (ca. 300 eV), where the X-rays are strongly attenuated, but also significant at higher photon energies where the carbon coating affects the reflectivity and surface shape of the mirrors. [1] The Swiss Light Source has typically relied on in-situ plasma cleaning to control mirror contamination and the PolLux scanning transmission X-ray microscopy (STXM) beamline has also been employing further contamination reduction strategies in recent years. In particular, in 2014 we installed a 1×10‑8 mbar background pressure of O2 on the PolLux first mirror chamber. We present a history of efforts to control optical contamination at the PolLux beamline and report on the observed efficiencies of the different processes employed both for the in-vacuum optics and critical components of the frequently vented STXM experiment chamber.

Probing the distribution and contamination levels of 10 trace metal/metalloids in soils near a Pb/Zn smelter in Middle China.

Science.gov (United States)

Li, Zhonggen; Feng, Xinbin; Bi, Xiangyang; Li, Guanghui; Lin, Yan; Sun, Guangyi

2014-03-01

The horizontal and vertical distribution patterns and contamination status of ten trace metal/metalloids (Ag, Bi, Co, Cr, Ge, In, Ni, Sb, Sn, Tl) in soils around one of the largest Chinese Pb-Zn smelter in Zhuzhou City, Central China, were revealed. Different soil samples were collected from 11 areas, including ten agricultural areas and one city park area, with a total of 83 surface soil samples and six soil cores obtained. Trace metal/metalloids were determined by inductively coupled plasma-mass spectrometry after digestion by an acid mixture of HF and HNO3. The results showed that Ag, Bi, In, Sb, Sn, and Tl contents decreased both with the distance to the Pb-Zn smelter as well as the soil depth, hinting that these elements were mainly originated from the Pb-Zn smelting operations and were introduced into soils through atmospheric deposition. Soil Ge was influenced by the smelter at a less extent, while the distributions of Co, Cr, and Ni were roughly even among most sampling sites and soil depths, suggesting that they were primarily derived from natural sources. The contamination status, as revealed by the geo-accumulation index (I geo), indicated that In and Ag were the most enriched elements, followed by Sb, Bi, and Sn. In general, Cr, Tl, Co, Ni, and Ge were of an uncontaminated status.

Atom trap trace analysis

Energy Technology Data Exchange (ETDEWEB)

Lu, Z.-T.; Bailey, K.; Chen, C.-Y.; Du, X.; Li, Y.-M.; O' Connor, T. P.; Young, L.

2000-05-25

A new method of ultrasensitive trace-isotope analysis has been developed based upon the technique of laser manipulation of neutral atoms. It has been used to count individual {sup 85}Kr and {sup 81}Kr atoms present in a natural krypton sample with isotopic abundances in the range of 10{sup {minus}11} and 10{sup {minus}13}, respectively. The atom counts are free of contamination from other isotopes, elements,or molecules. The method is applicable to other trace-isotopes that can be efficiently captured with a magneto-optical trap, and has a broad range of potential applications.

Plutonium contamination in the Maralinga Tjarutja lands

International Nuclear Information System (INIS)

Johnston, P.N.; Lokan, K.H.; Richardson, C.K.; Williams, G.A.

1989-08-01

Nuclear weapons trials conducted at Maralinga from 1960 to 1963 resulted in contamination of large areas of land with low levels of plutonium. Ground and aerial surveys and soil sampling conducted between 1984 and 1987 showed that this contamination extended beyond the boundaries of the area still controlled by the Commonwealth Government into the Maralinga Tjarutja lands. Levels of contamination beyond the boundaries of the former test range were found to be low, and were generally undetectable for all but the most sensitive measurement techniques. Soil sampling combined with long laboratory counting was initially used to define the trace levels but the contamination was found to be particulate with a surface density of particles too low for this to be a generally useful technique. The results are presented of in-situ gamma-ray spectrometry using a portable germanium (Ge) detector to measure contamination levels of plutonium to well below 1 kBq m -2 in the Maralinga Tjarutja lands to the north and north-west of the Maralinga test site. 8 refs., 10 figs., 10 tabs

Contamination of Detained Sediment in Sustainable Urban Drainage Systems

Directory of Open Access Journals (Sweden)

Deonie Allen

2017-05-01

Full Text Available Adsorption is a key water pollution remediation measure used to achieve stormwater quality improvement in Sustainable urban Drainage Systems (SuDS. The level of contamination of detained sediment within SuDS assets is not well documented, with published investigations limited to specific contaminant occurrence in ponds, wetlands or infiltration devices (bioretention cells and generally focused on solute or suspended sediment. Guidance on contamination threshold levels and potential deposited sediment contamination information is not included in current UK SuDS design or maintenance guidance, primarily due to a lack of evidence and understanding. There is a need to understand possible deposited sediment contamination levels in SuDS, specifically in relation to sediment removal maintenance activities and potential impact on receiving waterways of conveyed sediment. Thus, the objective of the research presented herein was to identify what major elements and trace metals were observable in (the investigated SuDS assets detained sediment, the concentration of these major elements and trace metals and whether they met/surpassed ecotoxicity or contaminated land thresholds. The research presented here provides evidence of investigated SuDS sediment major element and trace metal levels to help inform guidance and maintenance needs, and presents a new methodology to identify the general cause (anthropocentric land use and extent of detained SuDS fine urban sediment contamination through use of a contamination matrix.

Assessment of trace element stabilization in soil

OpenAIRE

Kumpiene, Jurate

2005-01-01

The thesis deals with the remediation of trace element contaminated soil by the chemical stabilization technique. The objective is to complement the knowledge about possibilities of applying the stabilization either (1) as an alternate soil remediation method to excavation and landfilling or (2) for a pre-treatment of contaminated soil before landfilling. The work is based on two case studies of the stabilization of 1) Cr, Cu, As, and Zn contaminated soil using metallic iron and 2) Pb and Cu ...

Demonstration/Validation of a Surface Cleaning Control to Mitigate Storm Water Metal Contaminants

Science.gov (United States)

2014-04-01

added to a pre- weighed 125-ml low density polyethylene (LDPE) bottle. The particles were digested with 1.0 ml of concentrated trace metal grade (TMG...Sorenson. 2005. “ Residential Street-Dirt Accumulation Rates and Chemical Composition, and Removal Efficiencies by Mechanical- and Vacuum-Type...Bay, and M. Kayhanian. 2003. “A Review of the Contaminants and Toxicity Associated with Particles in Stormwater Runoff.” Caltrans CTSW-RT-03-059.73.15

Spatial control of groundwater contamination, using principal

Indian Academy of Sciences (India)

Spatial control of groundwater contamination, using principal component analysis ... anthropogenic (agricultural activities and domestic wastewaters), and marine ... The PC scores reflect the change of groundwater quality of geogenic origin ...

UNDERWATER COATINGS FOR CONTAMINATION CONTROL

International Nuclear Information System (INIS)

Julia L. Tripp; Kip Archibald; Ann Marie Phillips; Joseph Campbell

2004-01-01

The Idaho National Laboratory (INL) deactivated several aging nuclear fuel storage basins. Planners for this effort were greatly concerned that radioactive contamination present on the basin walls could become airborne as the sides of the basins became exposed during deactivation and allowed to dry after water removal. One way to control this airborne contamination was to fix the contamination in place while the pool walls were still submerged. There are many underwater coatings available on the market for marine, naval and other applications. A series of tests were run to determine whether the candidate underwater fixatives were easily applied and adhered well to the substrates (pool wall materials) found in INL fuel pools. Lab-scale experiments were conducted by applying fourteen different commercial underwater coatings to four substrate materials representative of the storage basin construction materials, and evaluating their performance. The coupons included bare concrete, epoxy painted concrete, epoxy painted carbon steel, and stainless steel. The evaluation criteria included ease of application, adherence to the four surfaces of interest, no change on water clarity or chemistry, non-hazardous in final applied form and be proven in underwater applications. A proprietary two-part, underwater epoxy owned by S. G. Pinney and Associates was selected from the underwater coatings tested for application to all four pools. Divers scrubbed loose contamination off the basin walls and floors using a ship hull scrubber and vacuumed up the sludge. The divers then applied the coating using a special powered roller with two separate heated hoses that allowed the epoxy to mix at the roller surface was used to eliminate pot time concerns. The walls were successfully coated and water was removed from the pools with no detectable airborne contamination releases

Effect of fouling on removal of trace organic compounds by nanofiltration

Directory of Open Access Journals (Sweden)

S. Hajibabania

2011-12-01

Full Text Available The fate of chemical of concern is not yet fully understood during treatment of impaired waters. The aim of this paper is to assess the impact of different organic-based fouling layers on the removal of a large range of trace organics. Both model and real water samples (mixed with trace organic contaminants at environmental concentration of 2 μg l⁻¹ were used to simulate fouling in nanofiltration under controlled environment. The new and fouled membranes were systematically characterised for surface charge, hydrophobicity and roughness. It was observed that fouling generally reduced the membrane surface charge; however, the alterations of the membrane hydrophobicity and surface roughness were dependent on the foulants composition. The rejection of charged trace organics was observed to be improved due to the increased electrostatic repulsion by fouled membranes and the adsorption of the trace organic chemicals onto organic matters. On the other hand, the removal of nonionic compounds decreased when fouling occurred, due to the presence of cake enhanced concentration polarization. The fouling layer structure was found to play an important role in the rejection of the trace organic compounds.

Alternatives for contaminant control during MFTF plasma buildup

International Nuclear Information System (INIS)

Khan, J.M.; Valby, L.E.

1979-01-01

The MFTF mirror device considers all low-energy species to be contaminants, since their primary effect is to erode the plasma boundary by charge-exchange reactions. Confinement for other than hydrogen isotypes is far from complete and confinement time is hardly more than transit time from the source to the end wall. The brevity of the confinement time makes it all the more necessary to prevent any contamination which might further reduce it. At Livermore, the historical solution to contaminant control has been to evaporate titanium onto cold surfaces. An alternative to this approach and its implications are considered

Payload/orbiter contamination control requirement study: Preliminary contamination mission support plan. [a management analysis of project planning of spacecraft sterilization

Science.gov (United States)

Bareiss, L. E.; Hooper, V. W.; Ress, E. B.

1976-01-01

Progress is reported on the mission support plan and those support activities envisioned to be applicable and necessary during premission and postmission phases of the Spacelab program. The purpose, role, and requirements of the contamination control operations for the first two missions of the Spacelab equipped Space Transportation System are discussed. The organization of the contamination control operation and its relationship to and interfaces with other mission support functions is also discussed. Some specific areas of contamination to be investigated are treated. They are: (1) windows and viewports, (2) experiment equipment, (3) thermal control surfaces, (4) the contaminant induced atmosphere (as differentiated from the normal ambient atmosphere at the orbit altitude), and (5) optical navigation instruments.

Fate of trace element haps when applying mercury control technologies

Energy Technology Data Exchange (ETDEWEB)

Nyberg, Carolyn M.; Thompson, Jeffrey S.; Zhuang, Ye; Pavlish, John H. [University of North Dakota Energy and Environmental Research Center 15 North 23rd Street, Stop 9018, Grand Forks, North Dakota 58202-9018 (United States); Brickett, Lynn; Pletcher, Sara [U.S. Department of Energy National Energy Technology Laboratory 626 Cochrans Mill Road, PO Box 10940, MS 922-273C, Pittsburgh, PA 15236-0940 (United States)

2009-11-15

During the past several years, and particularly since the Clean Air Mercury Rule (CAMR) was promulgated in June of 2005, the electric utility industry, product vendors, and the research community have been working diligently to develop and test Hg control strategies for a variety of coal types and plant configurations. Some of these strategies include sorbent injection and chemical additives designed to increase mercury capture efficiency in particulate control devices. These strategies have the potential to impact the fate of other inorganic hazardous air pollutants (HAPs), which typically include As, Be, Cd, Cr, Co, Mn, Ni, Pb, Se, and Sb. To evaluate this impact, flue gas samples using EPA Method 29, along with representative coal and ash samples, were collected during recent pilot-scale and field test projects that were evaluating Hg control technologies. These test programs included a range of fuel types with varying trace element concentrations, along with different combustion systems and particulate control devices. The results show that the majority of the trace element HAPs are associated with the particulate matter in the flue gas, except for Se. However, for five of the six projects, Se partitioning was shifted to the particulate phase and total emissions reduced when Hg control technologies were applied. (author)

Optimization of the control of contamination at nuclear power plants

International Nuclear Information System (INIS)

Khan, T.A.; Baum, J.W.

1988-05-01

A methodology is described for the optimization of the actions taken to control contamination. It deals with many aspects of contamination, such as the monetary value assigned to a unit of radiation dose, the treatment of skin and extremity dose, and the inefficiencies introduced from working in a contaminated environemnt. The optimization method is illustrated with two case studies based on cleanup projects at nuclear power plants. Guidelines for the use of protective apparel, and for monitoring radiation and contamination at various levels of contamination are presented. The report concludes that additional research is required to quantify the effect of a contaminated environment on work efficiencies

Assessment of pesticide residues and trace element contamination ...

African Journals Online (AJOL)

ajl10

It was based on the chemical analyses of soil, water and vegetable samples. ... of the fine fraction (under 2 mm) were conserved away from light for ... To assess the migration and accumulation of trace elements ..... metals from sewage sludge in an agricultural soil. ... Pesticides and heavy metals in drinking water, soils.

Spatial control of groundwater contamination, using principal ...

Indian Academy of Sciences (India)

probe into the spatial controlling processes of groundwater contamination, using principal component analysis (PCA). ... topography, soil type, depth of water levels, and water usage. Thus, the ... of effective sites for infiltration of recharge water.

Changes in growth rate and macroelement and trace element accumulation in Hydrocharis morsus-ranae L. during the growing season in relation to environmental contamination.

Science.gov (United States)

Polechońska, Ludmiła; Samecka-Cymerman, Aleksandra; Dambiec, Małgorzata

2017-02-01

The temporal variations in plant chemistry connected with its life cycle may affect the cycling of elements in an ecosystem as well as determine the usefulness of the species in phytoremediation and bioindication. In this context, there is a gap in knowledge on the role of floating plants for elements cycling in aquatic reservoirs. The aim of the study was to determine if there are variations in Hydrocharis morsus-ranae (European frog-bit) bioaccumulation capacity and the growth rate of its population during the growing season and to test the impact of environmental pollution on these features. The content of macroelements (Ca, K, Mg, N, Na, P, S) and trace metals (Cd, Co, Cu, Cr, Hg, Fe, Mn, Ni, Pb, Zn) was determined in H. morsus-ranae collected monthly from June to October from habitats differing in environmental contamination. The results showed that the highest content of most trace metals (Co, Cr, Cu, Hg, Mn, Ni, Zn) and some nutrients (N, P) in plants as well as the greatest bioaccumulation efficiency occurred simultaneously in the beginning of the growing season. In the following months, a dilution effect (manifested by a decrease in content) related to the rapid growth was observed. Co, Mn, and Ni content in plant tissues reflected the level of environmental contamination throughout the growing season which makes H. morsus-ranae a potential biomonitor of pollution for these metals. Considering the great bioaccumulation ability, high sensitivity to contamination, and low biomass of European frog-bit in polluted systems, further investigation is required to assess the real phytoremediation capability of the species.

Relationships between soil parameters and physiological status of Miscanthus x giganteus cultivated on soil contaminated with trace elements under NPK fertilisation vs. microbial inoculation.

Science.gov (United States)

Pogrzeba, Marta; Rusinowski, Szymon; Sitko, Krzysztof; Krzyżak, Jacek; Skalska, Aleksandra; Małkowski, Eugeniusz; Ciszek, Dorota; Werle, Sebastian; McCalmont, Jon Paul; Mos, Michal; Kalaji, Hazem M

2017-06-01

Crop growth and development can be influenced by a range of parameters, soil health, cultivation and nutrient status all play a major role. Nutrient status of plants can be enhanced both through chemical fertiliser additions (e.g. N, P, K supplementation) or microbial fixation and mobilisation of naturally occurring nutrients. With current EU priorities discouraging the production of biomass on high quality soils there is a need to investigate the potential of more marginal soils to produce these feedstocks and the impacts of soil amendments on crop yields within them. This study investigated the potential for Miscanthus x giganteus to be grown in trace element (TE)-contaminated soils, ideally offering a mechanism to (phyto)manage these contaminated lands. Comprehensive surveys are needed to understand plant-soil interactions under these conditions. Here we studied the impacts of two fertiliser treatments on soil physico-chemical properties under Miscanthus x giganteus cultivated on Pb, Cd and Zn contaminated arable land. Results covered a range of parameters, including soil rhizosphere activity, arbuscular mycorrhization (AM), as well as plant physiological parameters associated with photosynthesis, TE leaf concentrations and growth performance. Fertilization increased growth and gas exchange capacity, enhanced rhizosphere microbial activity and increased Zn, Mg and N leaf concentration. Fertilization reduced root colonisation by AMF and caused higher chlorophyll concentration in plant leaves. Microbial inoculation seems to be a promising alternative for chemical fertilizers, especially due to an insignificant influence on the mobility of toxic trace elements (particularly Cd and Zn). Copyright © 2017 Elsevier Ltd. All rights reserved.

Musculoskeletal model-based control interface mimics physiologic hand dynamics during path tracing task

Science.gov (United States)

Crouch, Dustin L.; (Helen Huang, He

2017-06-01

Objective. We investigated the feasibility of a novel, customizable, simplified EMG-driven musculoskeletal model for estimating coordinated hand and wrist motions during a real-time path tracing task. Approach. A two-degree-of-freedom computational musculoskeletal model was implemented for real-time EMG-driven control of a stick figure hand displayed on a computer screen. After 5-10 minutes of undirected practice, subjects were given three attempts to trace 10 straight paths, one at a time, with the fingertip of the virtual hand. Able-bodied subjects completed the task on two separate test days. Main results. Across subjects and test days, there was a significant linear relationship between log-transformed measures of accuracy and speed (Pearson’s r  =  0.25, p  bodied subjects in 8 of 10 trials. For able-bodied subjects, tracing accuracy was lower at the extremes of the model’s range of motion, though there was no apparent relationship between tracing accuracy and fingertip location for the amputee. Our result suggests that, unlike able-bodied subjects, the amputee’s motor control patterns were not accustomed to the multi-joint dynamics of the wrist and hand, possibly as a result of post-amputation cortical plasticity, disuse, or sensory deficits. Significance. To our knowledge, our study is one of very few that have demonstrated the real-time simultaneous control of multi-joint movements, especially wrist and finger movements, using an EMG-driven musculoskeletal model, which differs from the many data-driven algorithms that dominate the literature on EMG-driven prosthesis control. Real-time control was achieved with very little training and simple, quick (~15 s) calibration. Thus, our model is potentially a practical and effective control platform for multifunctional myoelectric prostheses that could restore more life-like hand function for individuals with upper limb amputation.

Distribution and Potential Toxicity of Trace Metals in the Surface Sediments of Sundarban Mangrove Ecosystem, Bangladesh

Science.gov (United States)

Kumar, A.; Ramanathan, A.; Mathukumalli, B. K. P.; Datta, D. K.

2014-12-01

The distribution, enrichment and ecotoxocity potential of Bangladesh part of Sundarban mangrove was investigated for eight trace metals (As, Cd, Cr, Cu, Fe, Mn, Pb and Zn) using sediment quality assessment indices. The average concentration of trace metals in the sediments exceeded the crustal abundance suggesting sources other than natural in origin. Additionally, the trace metals profile may be a reflection of socio-economic development in the vicinity of Sundarban which further attributes trace metals abundance to the anthropogenic inputs. Geoaccumulation index suggests moderately polluted sediment quality w.r.t. Ni and As and background concentrations for Al, Fe, Mn, Cu, Zn, Pb, Co, As and Cd. Contamination factor analysis suggested low contamination by Zn, Cr, Co and Cd, moderate by Fe, Mn, Cu and Pb while Ni and As show considerable and high contamination, respectively. Enrichment factors for Ni, Pb and As suggests high contamination from either biota or anthropogenic inputs besides natural enrichment. As per the three sediment quality guidelines, Fe, Mn, Cu, Ni, Co and As would be more of a concern with respect to ecotoxicological risk in the Sundarban mangroves. The correlation between various physiochemical variables and trace metals suggested significant role of fine grained particles (clay) in trace metal distribution whereas owing to low organic carbon content in the region the organic complexation may not be playing significant role in trace metal distribution in the Sundarban mangroves.

Spatial and temporal analysis of the risks posed by total petroleum hydrocarbon and trace element contaminants in coastal waters of Kuwait.

Science.gov (United States)

Nicolaus, E E M; Wright, S R; Barry, J; Bolam, T P C; Ghareeb, K; Ghaloom, M; Al-Kanderi, N; Harley, B F M; Le Quesne, W J F; Devlin, M J; Lyons, B P

2017-07-15

Nine trace elements including As, Cd, Cu, Fe, Hg, Ni, Pb, V and Zn, and total petroleum hydrocarbons were analysed from water samples collected from 23 stations since 1984 from Kuwaiti coastal waters. Here it was investigated whether concentrations of these determinants are at levels above Kuwaiti and internationally established assessment criteria (AC). The results indicate that Cu and Cd had the most Kuwaiti AC breaches over time. Comparing the data of the last sampled year to the least stringent international AC, then Cu and Cd showed breaches at all stations. The trends for trace metals are significantly downwards, especially for Cd and Hg. No determinant measured showed a significant upward trend, indicating that water pollution for these contaminants is not a worsening situation. However, further sampling should be carried out to confirm these findings, especially at shoreline locations, where routine monitoring ceased in 2011 to investigate any recent changes. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Contamination Analysis Tools

Science.gov (United States)

Brieda, Lubos

2015-01-01

This talk presents 3 different tools developed recently for contamination analysis:HTML QCM analyzer: runs in a web browser, and allows for data analysis of QCM log filesJava RGA extractor: can load in multiple SRS.ana files and extract pressure vs. time dataC++ Contamination Simulation code: 3D particle tracing code for modeling transport of dust particulates and molecules. Uses residence time to determine if molecules stick. Particulates can be sampled from IEST-STD-1246 and be accelerated by aerodynamic forces.

Demonstration/Validation of a Surface Cleaning Control Practice to Mitigate Storm Water Metal Contaminants

Science.gov (United States)

2014-04-01

added to a pre- weighed 125-ml low density polyethylene (LDPE) bottle. The particles were digested with 1.0 ml of concentrated trace metal grade (TMG...consideration to ensure completion of operations.   33 9. REFERENCES Breault, R. F., K. P. Smith, and J. R. Sorenson. 2005. “ Residential Street...of the Contaminants and Toxicity Associated with Particles in Stormwater Runoff.” Caltrans CTSW-RT-03-059.73.15. California Department of

System to control contamination during retrieval of buried TRU waste

Science.gov (United States)

Menkhaus, Daniel E.; Loomis, Guy G.; Mullen, Carlan K.; Scott, Donald W.; Feldman, Edgar M.; Meyer, Leroy C.

1993-01-01

A system to control contamination during the retrieval of hazardous waste comprising an outer containment building, an inner containment building, within the outer containment building, an electrostatic radioactive particle recovery unit connected to and in communication with the inner and outer containment buildings, and a contaminate suppression system including a moisture control subsystem, and a rapid monitoring system having the ability to monitor conditions in the inner and outer containment buildings.

Assessment of Trace Metals Contamination of Surface Water and Sediment: A Case Study of Mvudi River, South Africa

Directory of Open Access Journals (Sweden)

Joshua N. Edokpayi

2016-02-01

Full Text Available Trace metals contamination of rivers and sediments remains a global threat to biodiversity and humans. This study was carried out to assess the variation pattern in trace metals contamination in Mvudi River water and sediments for the period of January–June 2014. Metal concentrations were analyzed using an inductively-coupled plasma optical emission spectrometer after nitric acid digestion. A compliance study for the water samples was performed using the guidelines of the Department of Water Affairs and Forestry (DWAF of South Africa and the World Health Organization (WHO. The National Oceanic and Atmospheric Administration (NOAA sediment quality guidelines for marine and estuarine sediments and the Canadian Council of Ministers of the Environment sediment guidelines (CCME for freshwater sediments were used to determine the possible toxic effects of the metals on aquatic organisms. pH (7.2–7.7 and conductivity (10.5–16.1 mS/m values complied with DWAF and WHO standards for domestic water use. Turbidity values in nephelometric turbidity units (NTU were in the range of 1.9–429 and exceeded the guideline values. The monthly average levels of trace metals in the water and sediments of Mvudi River were in the range of: Al (1.01–9.644 mg/L and 4296–5557 mg/kg, Cd (0.0003–0.002 mg/L and from below the detection limit to 2.19 mg/kg, Cr (0.015–0.357 mg/L and 44.23–149.52 mg/kg, Cu (0.024–0.185 mg/L and 13.22–1027 mg/kg, Fe (0.702–2.645 mg/L and 3840–6982 mg/kg, Mn (0.081–0.521 mg/L and 279–1638 mg/kg, Pb (0.002–0.042 mg/L and 1.775-4.157 mg/kg and Zn (0.031–0.261 mg/L and 14.481–39.88 mg/kg. The average concentrations of Al, Cr, Fe, Mn and Pb in the water samples exceeded the recommended guidelines of DWAF and WHO for domestic water use. High concentrations of Al and Fe were determined in the sediment samples. Generally, the concentrations of Cd, Cr and Cu in the sediments exceeded the corresponding effect range low

Trace elements and Pb isotopes in soils and sediments impacted by uranium mining

Energy Technology Data Exchange (ETDEWEB)

Cuvier, A., E-mail: alicia.cuvier@hotmail.fr [ECOLAB, Université de Toulouse, CNRS, INPT, UPS, Toulouse (France); IRSN/PRP-ENV/SESURE/Laboratoire d' études radioécologiques en milieu continental et marin, BP 1, 13108 Saint Paul Lez Durance Cedex (France); Pourcelot, L. [IRSN/PRP-ENV/SESURE/Laboratoire d' études radioécologiques en milieu continental et marin, BP 1, 13108 Saint Paul Lez Durance Cedex (France); Probst, A. [ECOLAB, Université de Toulouse, CNRS, INPT, UPS, Toulouse (France); Prunier, J. [Observatoire Midi-Pyrénées, laboratoire Géosciences Environnement Toulouse, CNRS/IRD/Université Paul Sabatier, 14 avenue Edouard Belin, 31400 Toulouse (France); Le Roux, G., E-mail: gael.leroux@ensat.fr [ECOLAB, Université de Toulouse, CNRS, INPT, UPS, Toulouse (France)

2016-10-01

The purpose of this study is to evaluate the contamination in As, Ba, Co, Cu, Mn, Ni, Sr, V, Zn and REE, in a high uranium activity (up to 21,000 Bq ∙ kg{sup −1}) area, downstream of a former uranium mine. Different geochemical proxies like enrichment factor and fractions from a sequential extraction procedure are used to evaluate the level of contamination, the mobility and the availability of the potential contaminants. Pb isotope ratios are determined in the total samples and in the sequential leachates to identify the sources of the contaminants and to determine the mobility of radiogenic Pb in the context of uranium mining. In spite of the large uranium contamination measured in the soils and the sediments (EF ≫ 40), trace element contamination is low to moderate (2 < EF < 5), except for Ba (5 < EF < 15), due to the precipitation of barium sulfate resulting from mining activities. Most of the trace elements are associated with the most mobile fractions of the sediments/soils, implying an enhanced potential availability. Even if no Pb enrichment is highlighted, the Pb isotopic signature of the contaminated soils is strongly radiogenic. Measurements performed on the sequential leachates reveal inputs of radiogenic Pb in the most mobile fractions of the contaminated soil. Inputs of low-mobile radiogenic Pb from mining activities may also contribute to the Pb signature recorded in the residual phase of the contaminated samples. We demonstrate that Pb isotopes are efficient tools to trace the origin and the mobility of the contaminants in environments affected by uranium mining. - Highlights: • Contamination of soils is evidenced by a multiproxy approach. • Enrichment factors highlight a low contamination except for U, S and Ba. • Pb isotope ratios point out inputs of radiogenic Pb from the mine. • Radiogenic Pb is mainly in the acid-soluble and the reducible fractions.

[Tracing the Fecal Contamination Sources Based on Bacteroides 16S rRNA PCR- DGGE in Karst Groundwater: Taking Laolongdong Underground River System, Nanshan, Chongqing as an Example].

Science.gov (United States)

Zhang, Hong; Jiang, Yong-jun; Zhang, Yuan-zhu; Duan, Yi-fan; Lü, Xian-fu; He, Qiu-fang

2016-05-15

Microbial contamination in karst groundwater continually increases and tracing the source researches has become a hot topic for international researchers. In this study, Laolongdong underground river at Nanshan, Chongqing was chosen as an example to adopt filter membrane methods to monitor the fecal microbial contaminations including the total bacterial concentration (TB), the total E. coli concentration (TE), the total fecal coliform (FC) and the total fecal Streptocoocci (FS). Bacteriodes was used as an indicator and PCR-DGGE analysis was used to trace fecal contamination sources in karst groundwater. The results suggested that groundwater in this area was seriously polluted by microbes from feces. The concentrations of microbial parameters exceeded limited levels greatly and the total bacterial amounts ranged 10-2.9 x 10⁷ CFU · mL⁻¹, the concentrations of E. coli were between 4.3-4.0 x 10⁵ CFU · mL⁻¹, the max concentration of FC was 1.1 x 10⁶ CFU · (100 mL)⁻¹ and the max concentration of FS was 1.1 x 10⁵ CFU · (100 mL)⁻¹. The FC/FS ratios were mostly over 2 which suggested that the main fecal source in groundwater was human feces. In addition, PCR-DGGE contrastive analysis of Bacteroides communities showed that the similarities between groundwater samples and human feces were in range of 7. 1% -69. 1% , and the similarity of the groundwater sample from Laolongdong underground river outlet was 69.1% . Bacteroides community similarities between groundwater samples and swine feces were in range of 1.1%-53.4%, and the similarity of Laolongdong underground river outlet was merely 1.5%. The similarity data implied that groundwater contamination resulted mainly from human feces, swine feces contamination composed part of animals' fecal contamination, and other animals' feces participated too. Furthermore, sequencing results of PCR-DGGE products revealed that most Bacteroides in groundwater originated from human intestinal tract and human feces.

Survey of reference materials. V. 2: Environmentally related reference materials for trace elements, nuclides and microcontaminants

International Nuclear Information System (INIS)

1996-05-01

The present report presently contains over 250 reference materials with trace element and organic contaminant information on fuel, geological and mineral, anthropogenic disposal, soil reference and miscellaneous reference materials. Not included in the current report is information on most biological and environmental reference materials with trace element, stable isotope, radioisotope and organic contaminant information. 8 refs, tabs

Translocation and accumulation of trace metals from the rhizosphere to the tomato and topinambur plants in a contaminated area of South Italy

Science.gov (United States)

Papa, Stefania; Bartoli, Giovanni; Álvarez-Romero, Marta; Zornoza, Raúl; Carillo, Petronia; Fioretto, Antonietta

2017-04-01

According to a survey of the Italian Environmental Monitoring Agency (ARPA), there are different critical sites in Campania region (South Italy) (e.i. legal or illegal landfills, countryside lands, abandoned farms, parking lots and regular streets). Literature data show that about half of the lead, cadmium and mercury contents, ingested through food, is due to the plant products (fruit, vegetables and grains) (Kachenko and Singh 2006; Liu et al 2012; Chang et al 2014; Wong et al 2002). In the health protection programs, the knowledge of heavy metals translocation from soils to plants used as food are very important with research on metal uptake by plants of food interest cultivated in contaminated soils. The goal of this work was to evaluate the translocation and accumulation of trace metals from the rhizosphere to the different parts of the plant (roots, stems, leaves, fruit) of Topinambur (Helianthus tuberosus) and tomato (Solanum lycopersicum) sampled in the coast area of Castel Volturno (Campania region, South Italy). This area is one of the critical sites according to a survey of the Environmental Monitoring Agency ARPA. In addition to these measures, malondialdehyde (MDA) activity was assayed to evaluate the stress state of the plant. The results showed that the trace metals concentration determinated in different organs of each species studied were more present in the roots than the other plant's parts, suggesting a probable block at root level. The only exception were Cu and Hg in tomato and topinambur plants respectively, that were mainly present in the leaves. The metals block at the root induced no alteration of MDA. However, the correlation between this activity and Cd, Pb, V and Hg seemed to attest to a possible synergy. Keywords: "Helianthus tuberosus", "Solanum lycopersicum", trace metal, traslocation Reference -Kachenko AG, Singh B, 2006 Heavy Metals Contamination in Vegetables Grown in Urban and Metal Smelter Contaminated Sites in Australia. Water

Radio contamination control on imported food. The bilberry case

International Nuclear Information System (INIS)

Zappa, S.; Calabrese, M.; Stancher, B.

2001-01-01

In this paper was pointed out the European regulation concerning the permissible limits of 137 Cs contamination in food importation, from countries affected by the consequences of the Chernobyl accident of 1986. A discussion about the control systems is lead and original data concerning the importation of the fruits of bilberry, a species particularly sensitive to radio contamination, are reported [it

Trace Metal Contamination in Water from Abandoned Mining and ...

African Journals Online (AJOL)

Fiifi Baidoo

copper and lead sulpho-salts (Dzigbordi-Adjimah, 1988). ... The resulting solution was analysed for trace metals at the Institute of Mining and Mineral ..... found in the samples (Tables 3 and 4) may be due to the mineral-water interactions and.

Trace elements contamination of soils around gold mine tailings ...

African Journals Online (AJOL)

ISHIOMA

Soil samples taken from depths of up to 12 cm and within a radius of 400 m from the ... Key words: Gold mining, tailings dam, trace elements, soil, Obuasi. INTRODUCTION ..... through soil might take considerably long time to manifest, probably ...

T cells recognizing a peptide contaminant undetectable by mass spectrometry

DEFF Research Database (Denmark)

Brezar, Vedran; Culina, Slobodan; Østerbye, Thomas

2011-01-01

Synthetic peptides are widely used in immunological research as epitopes to stimulate their cognate T cells. These preparations are never completely pure, but trace contaminants are commonly revealed by mass spectrometry quality controls. In an effort to characterize novel major histocompatibility...... complex (MHC) Class I-restricted ß-cell epitopes in non-obese diabetic (NOD) mice, we identified islet-infiltrating CD8+ T cells recognizing a contaminating peptide. The amount of this contaminant was so small to be undetectable by direct mass spectrometry. Only after concentration by liquid...... chromatography, we observed a mass peak corresponding to an immunodominant islet-specific glucose-6-phosphatase catalytic subunit-related protein (IGRP)(206-214) epitope described in the literature. Generation of CD8+ T-cell clones recognizing IGRP(206-214) using a novel method confirmed the identity...

Evaluation of two methods in controlling dental treatment water contamination.

Science.gov (United States)

Bansal, Ritu; Puttaiah, Raghunath; Harris, Robert; Reddy, Anil

2011-03-01

Dental unit water systems are contaminated with biofilms that amplify bacterial counts in dental treatment water in excess of a million colony forming units per milliliter (cfu/ml). The Centers for Disease Control and Prevention and the American Dental Association have agreed that the maximum allowable contamination of dental treatment water not exceed 500 cfu/ml. This study was conducted to evaluate two protocols in controlling contamination of dental unit water systems and dental treatment water. Both methods used an antimicrobial self-dissolving chlorine dioxide (ClO₂) tablet at a high concentration (50 ppm) to shock the dental unit water system biofilms initially followed by periodic exposure. To treat dental treatment source water for patient care, 3 parts per million (ppm) ClO₂ in municipal/tap water was compared to use of a citrus botanical extract dissolved in municipal water. Heterotrophic microbial counts of effluent water and laser scanning confocal microscopy were performed to evaluate effects of the two treatments. Results from this study indicated that both treatments were effective in controlling biofilm contamination and reducing heterotrophic plate counts Contemp Dent Pract 2011;12(2):73-83. Source of support: Nil Conflict of interest: None declared.

Forensic Luminol Blood Test for Preventing Cross-contamination in Dentistry: An Evaluation of a Dental School Clinic

OpenAIRE

Marcelo Carlos Bortoluzzi; Peterson Cadore; Andrea Gallon; Soraia Almeida Watanabe Imanishi

2014-01-01

Background: More than 200 different diseases may be transmitted from exposure to blood in the dental setting. The aim of this study is to identify possible faults in the cross-contamination chain control in a dental school clinic searching for traces of blood in the clinical contact surfaces (CCS) through forensic luminol blood test. Methods: Traces of invisible blood where randomly searched in CCS of one dental school clinic. Results: Forty eight surfaces areas in the CCS were tes...

Trace organic removal by photochemical oxidation

International Nuclear Information System (INIS)

Gupta, S.K. Sen; Peori, R.G.; Wickware, S.L.

1995-02-01

Photochemical oxidation methods can be used for the destruction of dissolved organic contaminants in most process effluent streams, including those originating from the nuclear power sector. Evaporators can be used to separate organic contaminants from the aqueous phase if they are non volatile, but a large volume of secondary waste (concentrate) is produced, and the technology is capital-intensive. This paper describes two different types of photochemical oxidation technologies used to destroy trace organics in wastewater containing oil and grease. (author). 9 refs., 4 figs

L-043: EPR-First Responders: Control of contamination resulting from the response

International Nuclear Information System (INIS)

2011-01-01

This conference is about the actions to be carried out by the first responders in a radiological emergency contamination control .The entrance and the exit to the contaminated area, the personnel dose, the waste and the equipment used are important aspects in the situation control

9 CFR 381.94 - Contamination with Microorganisms; process control verification criteria and testing; pathogen...

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Contamination with Microorganisms... § 381.94 Contamination with Microorganisms; process control verification criteria and testing; pathogen... maintaining process controls sufficient to prevent fecal contamination. FSIS shall take further action as...

Combined micro-droplet and thin-film-assisted pre-concentration of lead traces for on-line monitoring using anodic stripping voltammetry.

Science.gov (United States)

Belostotsky, Inessa; Gridin, Vladimir V; Schechter, Israel; Yarnitzky, Chaim N

2003-02-01

An improved analytical method for airborne lead traces is reported. It is based on using a Venturi scrubber sampling device for simultaneous thin-film stripping and droplet entrapment of aerosol influxes. At least threefold enhancement of the lead-trace pre-concentration is achieved. The sampled traces are analyzed by square-wave anodic stripping voltammetry. The method was tested by a series of pilot experiments. These were performed using contaminant-controlled air intakes. Reproducible calibration plots were obtained. The data were validated by traditional analysis using filter sampling. LODs are comparable with the conventional techniques. The method was successfully applied to on-line and in situ environmental monitoring of lead.

Combined micro-droplet and thin-film-assisted pre-concentration of lead traces for on-line monitoring using anodic stripping voltammetry

Energy Technology Data Exchange (ETDEWEB)

Belostotsky, Inessa; Gridin, Vladimir V.; Schechter, Israel; Yarnitzky, Chaim N. [Department of Chemistry, Technion Israel Institute of Technology, 32000, Haifa (Israel)

2003-02-01

An improved analytical method for airborne lead traces is reported. It is based on using a Venturi scrubber sampling device for simultaneous thin-film stripping and droplet entrapment of aerosol influxes. At least threefold enhancement of the lead-trace pre-concentration is achieved. The sampled traces are analyzed by square-wave anodic stripping voltammetry. The method was tested by a series of pilot experiments. These were performed using contaminant-controlled air intakes. Reproducible calibration plots were obtained. The data were validated by traditional analysis using filter sampling. LODs are comparable with the conventional techniques. The method was successfully applied to on-line and in situ environmental monitoring of lead. (orig.)

Certification of the methylmercury content in SRM 2977 mussel tissue (organic contaminants and trace elements) and SRM 1566b oyster tissue.

Science.gov (United States)

Tutschku, S; Schantz, M M; Horvat, M; Logar, M; Akagi, H; Emons, H; Levenson, M; Wise, S A

2001-02-01

The methylmercury content in two new marine bivalve mollusk tissue Standard Reference Materials (SRMs) has been certified using results of analyses from the National Institute of Standards and Technology (NIST) and two other laboratories. The certified concentrations of methylmercury were established based on the results from four and six different (independent) analytical methods, respectively, for SRM 1566b Oyster Tissue (13.2 +/- 0.7 microg/kg) and SRM 2977 Mussel Tissue (organic contaminants and trace elements) (36.2 +/- 1.7 microg/kg). The certified concentration of methylmercury in SRM 1566b is among the lowest in any certified reference material (CRM).

Limitations of sorption isotherms on modeling groundwater contaminant transport

International Nuclear Information System (INIS)

Silva, Eduardo Figueira da

2007-01-01

Design and safety assessment of radioactive waste repositories, as well as remediation of radionuclide contaminated groundwater require the development of models capable of accurately predicting trace element fate and transport. Adsorption of trace radionuclides onto soils and groundwater is an important mechanism controlling near- and far- field transport. Although surface complexation models (SCMs) can better describe the adsorption mechanisms of most radionuclides onto mineral surfaces by directly accounting for variability of system properties and mineral surface properties, isotherms are still used to model contaminant transport in groundwater, despite the much higher system dependence. The present work investigates differences between transport model results based on these two approaches for adsorption modeling. A finite element transport model is used for the isotherm model, whereas the computer program PHREEQC is used for the SCM approach. Both models are calibrated for a batch experiment, and one-dimensional transport is simulated using the calibrated parameters. At the lower injected concentrations there are large discrepancies between SCM and isotherm transport predictions, with the SCM presenting much longer tails on the breakthrough curves. Isotherms may also provide non-conservative results for time to breakthrough and for maximum concentration in a contamination plume. Isotherm models are shown not to be robust enough to predict transport behavior of some trace elements, thus discouraging their use. The results also illustrate the promise of the SCM modeling approach in safety assessment and environmental remediation applications, also suggesting that independent batch sorption measurements can be used, within the framework of the SCM, to produce a more versatile and realistic groundwater transport model for radionuclides which is capable of accounting more accurately for temporal and spatial variations in geochemical conditions. (author)

Behaviour study of trace radioelements in the cycles of uranium conversion

International Nuclear Information System (INIS)

Bertaux, M.

1998-01-01

The aim of this work was to study the presence of ultra-trace radioelements in the cycles of uranium conversion. Radiochemical methods for determining ultra-trace amounts of various elements in uranium have been perfected. These methods are based on the chromatographic separation of anionic complexes and on the measurement of various activities by alpha spectrometry. Thus, the source of these traces has been determined and a work of tracing has been carried out in the Malvesi site (uranium purification unit). This work has revealed an accumulation of these traces in the uranium purification column, consequently to their extraction by the TBP. A decontamination process of weakly contaminated uranium batches has been proposed using the Parex computer model and tested at the industrial scale. This process is based on the U(VI) extraction by the TBP/ISOPAR mixture and on the use of oxalic acid as the complexing agent of the tetravalent actinides in aqueous phase. It has been tested with success during a purification study of a batch of about 4 tons of uranium contaminated by traces of various radioelements. The preliminary study had taken into account the influence of metallic impurities (iron, nickel, copper) on the radioelements complexation by the oxalate ions. (O.M.)

Trace metal levels in sediments of Pearl Harbor (Hawaii)

International Nuclear Information System (INIS)

Ashwood, T.L.; Olsen, C.R.; Larsen, I.L.; Tamura, T.

1986-09-01

This study was conducted to measure the distribution of lead and other trace metals in the sediments of Pearl Harbon (Hawaii) to determine whether paint chips from vessels of the US Navy's Inactive Fleet have affected the environmental quality of Middle Loch. Sediment cores (ranging from 0.5 to 3.0 m long) were collected from Middle Loch near the Naval Inactive Ships Maintenance Facility and in an area of West Loch that is relatively isolated and unaffected by naval operations. Concentrations of copper, lead, and zinc averaged 180 μg/g, 49 μg/g, and 272 μg/g, respectively, in recent Middle Loch sediments. These concentrations are significantly higher than those in either historical Middle Loch sediments or recent West Loch sediments. However, except for lead, the concentrations in recent Middle Loch sediments are similar to those of older Middle Loch sediments, which indicates that the increase in trace metal contamination began before the onset of Inactive Fleet operations (about 1946). Increased trace metal levels in recent Middle Loch sediments might be expected to result from two potential sources: (1) sewage discharges and (2) paint from inactive vessels. Since paint contains elevated levels of lead and zinc but little copper, the elevated copper levels in Middle Loch sediments tend to implicate sewage as the source of trace metal contamination. Moreover, the lead:zinc ratio of recent Middle Loch sediments (0.18:1) is a factor of 10 lower than that measured in paint (2.1:1), and the Middle Loch lead:zinc ratio is not significantly greater than that measured in recent West Loch sediments (0.21:1). Hence, we suggest that sewage rather than paint is the major source of trace metal contamination of Middle Loch. This is consistent with the findings of a previous study by US navy personnel

Nuclear reaction analysis (NRA) for trace element detection

Energy Technology Data Exchange (ETDEWEB)

Doebeli, M. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Noll, K. [Bern Univ. (Switzerland)

1997-09-01

Ion beam induced nuclear reactions can be used to analyse trace element concentrations in materials. The method is especially suited for the detection of light contaminants in heavy matrices. (author) 3 figs., 2 refs.

Safe use of metal-contaminated agricultural land by cultivation of energy maize (Zea mays)

International Nuclear Information System (INIS)

Van Slycken, S.; Witters, N.; Meers, E.; Peene, A.; Michels, E.; Adriaensen, K.; Ruttens, A.; Vangronsveld, J.; Du Laing, G.; Wierinck, I.; Van Dael, M.; Van Passel, S.; Tack, F.M.G.

2013-01-01

Production of food crops on trace element-contaminated agricultural lands in the Campine region (Belgium) can be problematic as legal threshold values for safe use of these crops can be exceeded. Conventional sanitation of vast areas is too expensive and alternatives need to be investigated. Zea mays on a trace element-contaminated soil in the region showed an average yield of 53 ± 10 Mg fresh or 20 ± 3 Mg dry biomass ha −1 . Whole plant Cd concentrations complied with legal threshold values for animal feed. Moreover, threshold values for use in anaerobic digestion were met. Biogas production potential did not differ between maize grown on contaminated and non-contaminated soils. Results suggested favorable perspectives for farmers to generate non-food crops profitably, although effective soil cleaning would be very slow. This demonstrates that a valuable and sustainable alternative use can be generated for moderately contaminated soils on which conventional agriculture is impaired. -- Highlights: •Zea mays on trace element-contaminated soil has an average yield of 20 ± 3 Mg DW ha −1 . •Whole plant Cd concentrations complied with legal threshold values for animal feed. •Biogas production did not differ from maize grown on non-contaminated soils. •Perspectives are favorable for farmers to generate non-food crops profitably. •Effective soil cleaning would be very slow. -- Energy maize cultivation constitutes a sustainable alternative use of trace element-contaminated agricultural soils

Contamination Control and Hardware Processing Solutions at Marshall Space Flight Center

Science.gov (United States)

Burns, DeWitt H.; Hampton, Tammy; Huey, LaQuieta; Mitchell, Mark; Norwood, Joey; Lowrey, Nikki

2012-01-01

The Contamination Control Team of Marshall Space Flight Center's Materials and Processes Laboratory supports many Programs/ Projects that design, manufacture, and test a wide range of hardware types that are sensitive to contamination and foreign object damage (FOD). Examples where contamination/FOD concerns arise include sensitive structural bondline failure, critical orifice blockage, seal leakage, and reactive fluid compatibility (liquid oxygen, hydrazine) as well as performance degradation of sensitive instruments or spacecraft surfaces such as optical elements and thermal control systems. During the design phase, determination of the sensitivity of a hardware system to different types or levels of contamination/FOD is essential. A contamination control and FOD control plan must then be developed and implemented through all phases of ground processing, and, sometimes, on-orbit use, recovery, and refurbishment. Implementation of proper controls prevents cost and schedule impacts due to hardware damage or rework and helps assure mission success. Current capabilities are being used to support recent and on-going activities for multiple Mission Directorates / Programs such as International Space Station (ISS), James Webb Space Telescope (JWST), Space Launch System (SLS) elements (tanks, engines, booster), etc. The team also advances Green Technology initiatives and addresses materials obsolescence issues for NASA and external customers, most notably in the area of solvent replacement (e.g. aqueous cleaners containing hexavalent chrome, ozone depleting chemicals (CFC s and HCFC's), suspect carcinogens). The team evaluates new surface cleanliness inspection and cleaning technologies (e.g. plasma cleaning), and maintains databases for processing support materials as well as outgassing and optical compatibility test results for spaceflight environments.

Need for a contamination control textbook

International Nuclear Information System (INIS)

Stowers, I.F.; Patton, H.G.; Guntrum, S.K.

1980-01-01

Since the authors have become associated with contamination control technology they have repeatedly found themselves searching for technical information that was either never documented and therefore never reached a technical journal or was too specific to appear in a technical article. On countless occasions they have found other workers frustrated over the same lack of concise and up to date information in the relatively broad and interdisciplinary field of surface science, surface cleaning, and clean room operation and design. It is for these reasons that the authors wish to suggest formally that those engineers, chemists, technicians, and surface scientists working in this field collectively create a textbook that they may use as their first reference and teaching book. The text of this paper suggests a topical outline for a book and gives examples of the kinds of information that it should contain and the types of questions it should address. Included is an extensive bibliography recently collected showing the diversity of disciplines that those working in contamination control must be knowledgeable of and the variety of publications and journals in which these reports and articles are generally found

Application of hazard analysis critical control points (HACCP) to organic chemical contaminants in food.

Science.gov (United States)

Ropkins, K; Beck, A J

2002-03-01

Hazard Analysis Critical Control Points (HACCP) is a systematic approach to the identification, assessment, and control of hazards that was developed as an effective alternative to conventional end-point analysis to control food safety. It has been described as the most effective means of controlling foodborne diseases, and its application to the control of microbiological hazards has been accepted internationally. By contrast, relatively little has been reported relating to the potential use of HACCP, or HACCP-like procedures, to control chemical contaminants of food. This article presents an overview of the implementation of HACCP and discusses its application to the control of organic chemical contaminants in the food chain. Although this is likely to result in many of the advantages previously identified for microbiological HACCP, that is, more effective, efficient, and economical hazard management, a number of areas are identified that require further research and development. These include: (1) a need to refine the methods of chemical contaminant identification and risk assessment employed, (2) develop more cost-effective monitoring and control methods for routine chemical contaminant surveillance of food, and (3) improve the effectiveness of process optimization for the control of chemical contaminants in food.

Monsoon control on trace metal fluxes in the deep Arabian Sea

Indian Academy of Sciences (India)

Monsoon control on trace metal fluxes in the deep Arabian Sea ... at marine boundaries and surface ocean processes: Forcings and feedbacks Volume 115 ... Annual Al fluxes at shallow and deep trap depths were 0.47 and 0.46 gm−2 in the ...

Tracing control of chaos for the coupled dynamos dynamical system

International Nuclear Information System (INIS)

Wang Xuedi; Tian Lixin

2004-01-01

This paper introduces a new method for the coupled dynamos dynamical system, which can be applied to the decision of the chaotic behavior of the system. And research the tracing control of the chaos for the coupled dynamos dynamical system by gradually changing the driving parameter for the chaos. With the different design of controllers, the numerical simulation results show the relation between the chaotic behavior and the changes of the parameter value. Furthermore, the result shows the difference of the controllers. In the mean time, it reveals the process of the orbit's gradual changing with the parameter value

Enhanced desorption of PCB and trace metal elements (Pb and Cu) from contaminated soils by saponin and EDDS mixed solution

International Nuclear Information System (INIS)

Cao, Menghua; Hu, Yuan; Sun, Qian; Wang, Linling; Chen, Jing; Lu, Xiaohua

2013-01-01

This study investigated the simultaneous desorption of trace metal elements and polychlorinated biphenyl (PCB) from mixed contaminated soil with a novel combination of biosurfactant saponin and biodegradable chelant S,S-ethylenediaminedisuccinic acid (EDDS). Results showed significant promotion and synergy on Pb, Cu and PCB desorption with the mixed solution of saponin and EDDS. The maximal desorption of Pb, Cu and PCB were achieved 99.8%, 85.7% and 45.7%, respectively, by addition of 10 mM EDDS and 3000 mg L −1 saponin. The marked interaction between EDDS and saponin contributed to the synergy performance. The sorption of EDDS and saponin on soil was inhibited by each other. EDDS could enhance the complexation of metals with the saponin micelles and the solubilization capabilities of saponin micelles for PCB. Our study suggests the combination of saponin and EDDS would be a promising alternative for remediation of co-contaminated soils caused by hydrophobic organic compounds (HOCs) and metals. -- Highlights: ► A novel combination of biosurfactant saponin and EDDS was used to simultaneously remove mixed contaminations from soil. ► Significant synergy on Pb, Cu and PCB desorption were achieved with EDDS/saponin. ► The marked interaction between EDDS and saponin contributed to the synergy performance. -- Significant synergistic effect on Pb, Cu and PCB desorption were achieved with the mixed solution of saponin and EDDS

Characterization of atmospheric trace elements in the Puruogangri ice core: a preliminary account of Tibetan Plateau environmental and contamination histories

Science.gov (United States)

Beaudon, E.; Gabrielli, P.; Sierra Hernandez, R.; Wegner, A.; Thompson, L. G.

2014-12-01

Asia is facing enormous challenges including large-scale environmental changes, rapid population growth and industrialization. The inherent generated pollution contributes to half of all Earth's anthropogenic trace metals emissions that, when deposited to glaciers of the surrounding mountains of the Third Pole region, leave a characteristic chemical fingerprint. Records of past atmospheric deposition preserved in snow and ice from Third Pole glaciers provide unique insights into changes of the chemical composition of the atmosphere and into the nature and intensity of the regional atmospheric circulation systems. The determination of the elemental composition of aeolian dust stored in Himalayan and Tibetan Plateau glaciers can help to qualify the potential contamination of glacial meltwater as a part of the greater fresh Asian water source. The 215 m long Puruogangri ice core retrieved in 2000 at 6500 m a.s.l. in central Tibetan Plateau (Western Tanggula Shan, China) provides one of the first multi-millennium-long environmental archives (spanning the last 7000 years and annually resolved for the last 400 years) obtained from the Tibetan Plateau region. The Puruogangri's area is climatologically of particular interest because of its location at the boundary between the monsoon (wet) and the westerly (dry) dominated atmospheric circulation. The major objective of this study is to determine the concentration of trace and ultra-trace elements in the Puruogangri ice core between 1600 and 2000 AD in order to characterize the atmospheric aerosols entrapped in the ice. Particular attention is given to assess the amount of trace elements originating from anthropogenic sources during both the pre-industrial and industrial periods. The distinction between the anthropogenic contribution and the crustal background may rely on the precise decoupling of the dry and wet seasons signals, the former being largely influenced by dust contribution.

Effects of ozone and ozone/peroxide on trace organic contaminants and NDMA in drinking water and water reuse applications.

Science.gov (United States)

Pisarenko, Aleksey N; Stanford, Benjamin D; Yan, Dongxu; Gerrity, Daniel; Snyder, Shane A

2012-02-01

An ozone and ozone/peroxide oxidation process was evaluated at pilot scale for trace organic contaminant (TOrC) mitigation and NDMA formation in both drinking water and water reuse applications. A reverse osmosis (RO) pilot was also evaluated as part of the water reuse treatment train. Ozone/peroxide showed lower electrical energy per order of removal (EEO) values for TOrCs in surface water treatment, but the addition of hydrogen peroxide increased EEO values during wastewater treatment. TOrC oxidation was correlated to changes in UV(254) absorbance and fluorescence offering a surrogate model for predicting contaminant removal. A decrease in N-nitrosodimethylamine (NDMA) formation potential (after chloramination) was observed after treatment with ozone and ozone/peroxide. However, during spiking experiments with surface water, ozone/peroxide achieved limited destruction of NDMA, while in wastewaters net direct formation of NDMA of 6-33 ng/L was observed after either ozone or ozone/peroxide treatment. Once formed during ozonation, NDMA passed through the subsequent RO membranes, which highlights the significance of the potential for direct NDMA formation during oxidation in reuse applications. Copyright © 2011 Elsevier Ltd. All rights reserved.

Development of monitoring and control technology based on trace gas monitoring. Final report

Energy Technology Data Exchange (ETDEWEB)

Liebowitz, B.

1997-07-01

Trace gases are generated by many biological reactions. During anaerobic decomposition, trace levels of hydrogen (H{sub 2}) and carbon monoxide (CO) gases are produced. It was shown previously that these trace gases are intrinsically related to the biochemical reactions occurring and, therefore, offer promise for on-line process monitoring and control. This work was designed to test how effectively hydrogen and CO could be to monitor high-rate anaerobic systems that has significant mass transfer and complex hydraulics. An experimental program was designed to examine the behavior of an upflow anaerobic sludge blanket (UASB) reactor system under steady state and in response to organic loading perturbations. The responses of trace gases CO and H{sub 2} were tracked using an on-line, real-time gas-monitoring system linked to a computer-controlled data acquisition package. Data on conventional process parameters such as pH, chemical oxygen demand (COD), volatile fatty acids (VFAs) were concurrently collected. Monitoring of conventional process indicators (i.e., pH, VFA, gas production) and trace gas (H{sub 2} and CO) indicators was conducted using a matrix of nine different steady-state OLRs (4-23 kg COD/m{sup 3} -d) and system HRTs (0.5 to 2.5 days) was performed to determine any correlation among the indicators. Of OLR, HRT, and influent COD, only OLR had any significant influence on the process indicators examined. All parameters except methane increased with increases in OLR; methane decreased with increased OLR. The OLR and gas production rate (GP) were observed to be linearly correlated.

Surface Contaminant Control Technologies to Improve Laser Damage Resistance of Optics

Directory of Open Access Journals (Sweden)

Xiaofeng Cheng

2014-01-01

Full Text Available The large high-power solid lasers, such as the National Ignition Facility (NIF of America and the Shenguang-III (SG-III laser facility of China, can output over 2.1 MJ laser pulse for the inertial confinement fusion (ICF experiments. Because of the enhancement of operating flux and the expansion of laser driver scale, the problem of contamination seriously influences their construction period and operation life. During irradiation by intense laser beams, the contaminants on the metallic surface of beam tubes can be transmitted to the optical surfaces and lead to damage of optical components. For the high-power solid-state laser facilities, contamination control focuses on the slab amplifiers, spatial filters, and final-optical assemblies. In this paper, an effective solution to control contaminations including the whole process of the laser driver is put forward to provide the safe operation of laser facilities, and the detailed technical methods of contamination control such as washing, cleanliness metrology, and cleanliness protecting are also introduced to reduce the probability of laser-induced damage of optics. The experimental results show that the cleanliness level of SG-III laser facility is much better to ensure that the laser facility can safely operate at high energy flux.

Trace elements and nutrients adsorption onto nano-maghemite in a contaminated-soil solution: A geochemical/statistical approach.

Science.gov (United States)

Martínez-Fernández, Domingo; Bingöl, Deniz; Komárek, Michael

2014-07-15

Two experiments were carried out to study the competition for adsorption between trace elements (TEs) and nutrients following the application of nano-maghemite (NM) (iron nano-oxide; Fe2O3) to a soil solution (the 0.01molL(-1) CaCl2 extract of a TEs-contaminated soil). In the first, the nutrients K, N, and P were added to create a set of combinations: potential availability of TEs during their interaction with NM and nutrients were studied. In the second, response surface methodology was used to develop predictive models by central composite design (CCD) for competition between TEs and the nutrients K and N for adsorption onto NM. The addition of NM to the soil solution reduced specifically the concentrations of available As and Cd, but the TE-adsorption capacity of NM decreased as the P concentration increased. The CCD provided more concise and valuable information, appropriate to estimate the behavior of NM sequestering TEs: according to the suggested models, K(+) and NH4(+) were important factors for Ca, Fe, Mg, Mn, Na, and Zn adsorption (Radj(2)=95%, except for Zn with Radj(2)=87%). The obtained information and models can be used to predict the effectiveness of NM for the stabilization of TEs, crucial during the phytoremediation of contaminated soils. Copyright © 2014 Elsevier B.V. All rights reserved.

Woody biomass phytoremediation of contaminated brownfield land

Energy Technology Data Exchange (ETDEWEB)

French, Christopher J. [School of Biological and Earth Sciences, Liverpool John Moores University, Byrom Street, Liverpool L3 3AF (United Kingdom); Dickinson, Nicholas M. [School of Biological and Earth Sciences, Liverpool John Moores University, Byrom Street, Liverpool L3 3AF (United Kingdom)]. E-mail: n.m.dickinson@livjm.ac.uk; Putwain, Philip D. [Ecological Restoration Consultants (ERC), Ness Botanic Gardens, University of Liverpool, Ness, Cheshire CH64 (United Kingdom)

2006-06-15

Economic and environmental regeneration of post-industrial landscapes frequently involves some element of re-afforestation or tree planting. We report field trials that evaluate whether woody biomass production is compatible with managing residual trace element contamination in brownfield soils. Large-scale mapping of contamination showed a heterogenous dispersion of metals and arsenic, and highly localised within-site hotspots. Yields of Salix, Populus and Alnus were economically viable, showing that short-rotation coppice has a potentially valuable role in community forestry. Mass balance modelling demonstrated that phytoextraction potentially could reduce contamination hotspots of more mobile elements (Cd and Zn) within a 25-30-year life cycle of the crops. Cd and Zn in stems and foliage of Salix were 4-13 times higher than EDTA-extractable soil concentrations. Lability of other trace elements (As, Pb, Cu, Ni) was not increased 3 years after planting the coppice; woody biomass may provide an effective reduction of exposure (phytostabilisation) to these less mobile contaminants. - Field trials show short-rotation coppice provides effective risk management and remediation solutions to hotspots of residual metal and As contamination of brownfield land.

Woody biomass phytoremediation of contaminated brownfield land

International Nuclear Information System (INIS)

French, Christopher J.; Dickinson, Nicholas M.; Putwain, Philip D.

2006-01-01

Economic and environmental regeneration of post-industrial landscapes frequently involves some element of re-afforestation or tree planting. We report field trials that evaluate whether woody biomass production is compatible with managing residual trace element contamination in brownfield soils. Large-scale mapping of contamination showed a heterogenous dispersion of metals and arsenic, and highly localised within-site hotspots. Yields of Salix, Populus and Alnus were economically viable, showing that short-rotation coppice has a potentially valuable role in community forestry. Mass balance modelling demonstrated that phytoextraction potentially could reduce contamination hotspots of more mobile elements (Cd and Zn) within a 25-30-year life cycle of the crops. Cd and Zn in stems and foliage of Salix were 4-13 times higher than EDTA-extractable soil concentrations. Lability of other trace elements (As, Pb, Cu, Ni) was not increased 3 years after planting the coppice; woody biomass may provide an effective reduction of exposure (phytostabilisation) to these less mobile contaminants. - Field trials show short-rotation coppice provides effective risk management and remediation solutions to hotspots of residual metal and As contamination of brownfield land

Sandhopper solar orientation as a behavioural biomarker of trace metals contamination

International Nuclear Information System (INIS)

Ungherese, Giuseppe; Ugolini, Alberto

2009-01-01

Although many studies have focused on trace metals accumulation, investigations of talitrid amphipods as biomarkers are rare. This study explores the possibility of using the solar orientation capacity of Talitrus saltator as a behavioural marker of exposure to two essential (Cu and Zn) and two non-essential (Cd and Hg) metals. LC 50 analyses performed before the solar orientation tests showed that the 72 h LC 50 for Hg was 0.02 ppm while the 96 h LC 50 values for Cu, Cd and Zn were 13.28 ppm, 27.66 ppm, and 62.74 ppm, respectively. The presence of metals in seawater affects the solar orientation capacity of T. saltator in a concentration-dependent manner and according to the toxicity ranking of the metals (Hg > Cu > Cd > Zn). Therefore, the solar orientation capacity of T. saltator seems to be a promising behavioural marker for exposure to trace metals. - Solar orientation capacity is a promising behavioural marker for exposure to trace metals in sandhoppers

Combined Contamination and Space Environmental Effects on Solar Cells and Thermal Control Surfaces

Science.gov (United States)

Dever, Joyce A.; Bruckner, Eric J.; Scheiman, David A.; Stidham, Curtis R.

1994-01-01

For spacecraft in low Earth orbit (LEO), contamination can occur from thruster fuel, sputter contamination products and from products of silicone degradation. This paper describes laboratory testing in which solar cell materials and thermal control surfaces were exposed to simulated spacecraft environmental effects including contamination, atomic oxygen, ultraviolet radiation and thermal cycling. The objective of these experiments was to determine how the interaction of the natural LEO environmental effects with contaminated spacecraft surfaces impacts the performance of these materials. Optical properties of samples were measured and solar cell performance data was obtained. In general, exposure to contamination by thruster fuel resulted in degradation of solar absorptance for fused silica and various thermal control surfaces and degradation of solar cell performance. Fused silica samples which were subsequently exposed to an atomic oxygen/vacuum ultraviolet radiation environment showed reversal of this degradation. These results imply that solar cells and thermal control surfaces which are susceptible to thruster fuel contamination and which also receive atomic oxygen exposure may not undergo significant performance degradation. Materials which were exposed to only vacuum ultraviolet radiation subsequent to contamination showed slight additional degradation in solar absorptance.

Worldwide Interlaboratory Comparison on the Determination of Trace Elements in the IAEA-457 Marine Sediment Sample

International Nuclear Information System (INIS)

2016-01-01

The primary goal of the IAEA Environment Laboratories is to assist Member States in the use of both stable and radioisotope analytical techniques to understand, monitor and protect the environment. In this context, the major impact of large coastal cities on marine ecosystems is an issue of primary concern for the IAEA and the IAEA Environment Laboratories. The marine pollution assessments required to understand such impacts depend on accurate knowledge of contaminant concentrations in various environmental compartments. Through the IAEA Environment Laboratories, the IAEA has been assisting national laboratories and regional laboratory networks since the early 1970s through the provision of a reference material programme for the analysis of radionuclides, trace elements and organic compounds in marine samples. Quality assurance and quality control are two fundamental requirements to ensure the reliability of analytical results. Data that are not based on adequate quality assurance and quality control can be erroneous, and their misuse can lead to poor environmental management decisions. In this regard, the IAEA has a long history of organizing interlaboratory studies, which have evolved to include an increasing array of potential contaminants in the marine environment. Relevant activities comprise global interlaboratory comparison, regional proficiency tests, the production of marine reference materials and the development of reference methods for trace elements and organic pollutants analysis in marine samples. This publication summarizes the results of the IAEA-457 interlaboratory comparison on the determination of trace elements in a marine sediment sample

Controlling Beryllium Contaminated Material And Equipment For The Building 9201-5 Legacy Material Disposition Project

International Nuclear Information System (INIS)

Reynolds, T.D.; Easterling, S.D.

2010-01-01

This position paper addresses the management of beryllium contamination on legacy waste. The goal of the beryllium management program is to protect human health and the environment by preventing the release of beryllium through controlling surface contamination. Studies have shown by controlling beryllium surface contamination, potential airborne contamination is reduced or eliminated. Although there are areas in Building 9201-5 that are contaminated with radioactive materials and mercury, only beryllium contamination is addressed in this management plan. The overall goal of this initiative is the compliant packaging and disposal of beryllium waste from the 9201-5 Legacy Material Removal (LMR) Project to ensure that beryllium surface contamination and any potential airborne release of beryllium is controlled to levels as low as practicable in accordance with 10 CFR 850.25.

Trace element accumulation in woody plants of the Guadiamar Valley, SW Spain: A large-scale phytomanagement case study

International Nuclear Information System (INIS)

Dominguez, Maria T.; Maranon, Teodoro; Murillo, Jose M.; Schulin, Rainer; Robinson, Brett H.

2008-01-01

Phytomanagement employs vegetation and soil amendments to reduce the environmental risk posed by contaminated sites. We investigated the distribution of trace elements in soils and woody plants from a large phytomanaged site, the Guadiamar Valley (SW Spain), 7 years after a mine spill, which contaminated the area in 1998. At spill-affected sites, topsoils (0-25 cm) had elevated concentrations of As (129 mg kg -1 ), Bi (1.64 mg kg -1 ), Cd (1.44 mg kg -1 ), Cu (115 mg kg -1 ), Pb (210 mg kg -1 ), Sb (13.8 mg kg -1 ), Tl (1.17 mg kg -1 ) and Zn (457 mg kg -1 ). Trace element concentrations in the studied species were, on average, within the normal ranges for higher plants. An exception was white poplar (Populus alba), which accumulated Cd and Zn in leaves up to 3 and 410 mg kg -1 respectively. We discuss the results with regard to the phytomanagement of trace element contaminated sites. - There is a low trace element transfer from contaminated soils to the aboveground parts of afforested woody plants under a semi-arid climate

Study on trace element determination in liver samples of great-white-egret Ardea alba Linnaeus, 1758 (Ardeidae, Aves) for environmental contamination biomionitoring

International Nuclear Information System (INIS)

Silva, Rita de Cassia A.; Saiki, Mitiko

2009-01-01

Predatory birds such as herons have been used as bioindicators of pollution since they are at the top of their food webs. The tissues of these animals are analyzed for assessing environmental pollution caused by toxic elements. In the present study, adequate experimental conditions were established for determination of trace elements concentrations in the liver samples of Great-white-egret (Ardea alba Linnaeus, 1758) for further application of this specimens as a bioindicator of environmental contamination. Four liver samples were collected from Greatwhite- egrets found in the metropolitan region of Sao Paulo and were they analyzed by the method of neutron activation analysis (NAA). Concentrations of the elements Br, Co, Cs, Fe, Na, Rb, Se and Zn were measured in these liver tissues. The findings of this present study demonstrated that the established procedure for liver sample treatment was appropriate to obtain a homogeneous sample. The method of neutron activation analysis (NAA) was very promising for liver sample analysis for evaluation of environmental contamination. (author)

Study on trace element determination in liver samples of great-white-egret Ardea alba Linnaeus, 1758 (Ardeidae, Aves) for environmental contamination biomionitoring

Energy Technology Data Exchange (ETDEWEB)

Silva, Rita de Cassia A.; Saiki, Mitiko, E-mail: rcsilva@ipen.b, E-mail: mitiko@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2009-07-01

Predatory birds such as herons have been used as bioindicators of pollution since they are at the top of their food webs. The tissues of these animals are analyzed for assessing environmental pollution caused by toxic elements. In the present study, adequate experimental conditions were established for determination of trace elements concentrations in the liver samples of Great-white-egret (Ardea alba Linnaeus, 1758) for further application of this specimens as a bioindicator of environmental contamination. Four liver samples were collected from Greatwhite- egrets found in the metropolitan region of Sao Paulo and were they analyzed by the method of neutron activation analysis (NAA). Concentrations of the elements Br, Co, Cs, Fe, Na, Rb, Se and Zn were measured in these liver tissues. The findings of this present study demonstrated that the established procedure for liver sample treatment was appropriate to obtain a homogeneous sample. The method of neutron activation analysis (NAA) was very promising for liver sample analysis for evaluation of environmental contamination. (author)

Organochlorine and trace element contamination in wintering and migrating diving ducks in the southern Great Lakes, USA, since the zebra mussel invasion

Science.gov (United States)

Custer, Christine M.; Custer, T.W.

2000-01-01

Because of the potential for increased trophic transfer of contaminants by zebra mussels (Dreissena sp.) to higher trophic levels, we collected four species of waterfowl (n = 65 ducks) from four locations in Lake Erie, Lake St. Clair, and Lake Michigan, USA, between 1991 and 1993 for organochlorine contaminant and trace element analyses. Geometric mean concentrations of total polychlorinated biphenyls (PCBs) and p,pa??-dichlorodiphenyldichloroethylene (DDE) were 1.35 and 0.15 I?g/g wet weight in lesser scaup (Aythya affinis) carcasses and were below known effect levels. Total PCBs in 80% of carcasses, however, were above the U.S. Food and Drug Administration's threshold of 3.0 I?g/g lipid weight for consumption of poultry. With the exception of selenium, trace elements were also at background or no-effect levels. Selenium concentrations in livers of 95% of lesser scaup, 90% of bufflehead (Bucephala albeola), and 72% of common goldeneye (Bucephala clangula) were in the elevated (>10 I?g/g dry wt) or potentially harmful range (>33 I?g/g dry wt). The effects of these high selenium concentrations are unknown but should be investigated further based on reproductive effects observed in field and laboratory studies of dabbling ducks and because lesser scaup populations are declining. Concentrations of total PCBs in dreissenid mussels in western Lake Erie were 10 times higher than in the upper Mississippi River but were similar to concentrations in other industrialized rivers in Europe and the United States. Metal concentrations were similar to other industrialized sites where zebra mussels have been sampled.

Temporal and spatial distributions of contaminants in sediments of Santa Monica Bay, California

Science.gov (United States)

Bay, S.M.; Zeng, E.Y.; Lorenson, T.D.; Tran, K.; Alexander, Corrine

2003-01-01

Contaminant inputs from wastewater discharge, a major source of contamination to Santa Monica Bay (SMB), have declined drastically during the last three decades as a result of improved treatment processes and better source control. To assess the concomitant temporal changes in the SMB sediments, a study was initiated in June 1997, in which 25 box cores were collected using a stratified random sampling design. Five sediment strata corresponding to the time intervals of 1890-1920, 1932-1963, 1965-1979, 1979-1989, and 1989-1997 were identified using 210Pb dating techniques. Samples from each stratum were analyzed for metals, 1,1,1-Trichloro-2,2-bis(p-chlorophenyl)ethane (DDT) and its metabolites (DDTs), polychlorinated biphenyls (PCBs), and total organic carbon (TOC). Samples from the 1965-1979, 1979-1989, and 1989-1997 strata were also analyzed for polycyclic aromatic hydrocarbons (PAHs) and linear alkylbenzenes (LABs). Sediment metal concentrations increased from 1890-1979 and were similar during the time intervals of 1965-1979, 1979-1989, and 1989-1997, although the mass emissions of trace metals from sewage inputs declined substantially during the same time period. Trace organic contamination in SMB was generally highest in sediments corresponding to deposition during the years of 1965-1979 or 1979-1989 and showed a decline in concentration in the 1989-1997 stratum. Temporal trends of contamination were greatest in sediments collected from areas near the Hyperion Treatment Plant (HTP) outfall system and on the slope of Redondo Canyon. The highest contaminant concentrations were present in sediments near the HTP 7-mile outfall in the 1965-1979 stratum. Elevated trace metal and organic concentrations were still present in the 1989-1997 stratum of most stations, suggesting that sediment contaminants have moved vertically in the sediment column since sludge discharges from the 7-mile outfall (a dominant source of contamination to the bay) ceased in 1987. The

Raffinage des huiles et des corps gras et élimination des contaminants

Directory of Open Access Journals (Sweden)

Pages Xavier

2010-03-01

Full Text Available Refining is a powerful technology to guarantee a high food grade quality of the refined oils and fats. This overview of many of the safety challenges related to different contaminant residues, the refining processes have to and actually do respond to, focuses for each contaminant (pesticides, polycyclic hydrocarbons, other compounds as extraction solvent, metallic element traces, aflatoxins, dioxins and polychlorobiphenyls, and new appearing contaminants like phthalates and 3-monochloropropanediol esters on their nature, origin, occurrence and regulatory status before describing the required conditions of their elimination by chemical and “physical” refining with the mention of the most efficient refining step as known from the GMP or identified from original experimental works. Identifying the physicochemical characteristics (hydro-solubility, lipophilic property, molecular weight and vapour pressure indicative of a potential contaminant behaviour during refining is an interesting preliminary orientation tool. The quality target for refined oils and fats include on one hand the control and optimisation of organoleptic and nutritional characteristics as well as stability during further storage, and on the other hand, the elimination of contaminants avoiding or controlling the formation of new undesirable compounds. For each contaminant to be eliminated, the technological issues have to be found at the crossroads of these demands.

Highly efficient removal of trace thallium from contaminated source waters with ferrate: Role of in situ formed ferric nanoparticle.

Science.gov (United States)

Liu, Yulei; Wang, Lu; Wang, Xianshi; Huang, Zhuangsong; Xu, Chengbiao; Yang, Tao; Zhao, Xiaodan; Qi, Jingyao; Ma, Jun

2017-11-01

Thallium (Tl) is highly toxic to mammals and relevant pollution cases are increasing world-widely. Convenient and efficient method for the removal of trace Tl from contaminated source water is imperative. Here, the removal of trace Tl by K 2 FeO 4 [Fe(VI)] was investigated for the first time, with the exploration of reaction mechanisms. Six different types of water treatment agents (powdered activated carbon, Al 2 (SO 4 ) 3 , FeCl 3 , δ-MnO 2 , MnO 2 nano-particles, and K 2 FeO 4 ) were used for the removal of Tl in spiked river water, and K 2 FeO 4 showed excellent removal performance. Over 92% of Tl (1 μg/L) was removed within 5 min by applying 2.5 mg/L of K 2 FeO 4 (pH 7.0, 20 °C). XPS analysis revealed that in the reaction of Tl(I) with K 2 FeO 4 , Tl(I) was oxidized to Tl(III), and removed by the K 2 FeO 4 reduced ferric particles. The removal of Tl by in situ formed and ex situ formed ferric particle was examined respectively, and the results revealed that the removal of trace Tl could be attributed to the combination of adsorption and coprecipitation processes. The hydrodynamic size of the reduced particle from K 2 FeO 4 ranged from 10 nm to 100 nm, and its surface was negatively charged under neutral pH condition. These factors were conducive for the efficient removal of Tl by K 2 FeO 4 . The effects of solution pH, coexisting ions (Na + , Ca 2+ , and HCO 3 - ), humic acid, solution temperature, and reductive environment on the removal and desorption of Tl were investigated, and the elimination of Tl in polluted river water and reservoir water was performed. These results suggest that K 2 FeO 4 could be an efficient and convenient agent on trace Tl removal. Copyright © 2017. Published by Elsevier Ltd.

Contaminated Mexican steel incident

International Nuclear Information System (INIS)

1985-01-01

This report documents the circumstances contributing to the inadvertent melting of cobalt 60 (Co-60) contaminated scrap metal in two Mexican steel foundries and the subsequent distribution of contaminated steel products into the United States. The report addresses mainly those actions taken by US Federal and state agencies to protect the US population from radiation risks associated with the incident. Mexico had much more serious radiation exposure and contamination problems to manage. The United States Government maintained a standing offer to provide technical and medical assistance to the Mexican Government. The report covers the tracing of the source to its origin, response actions to recover radioactive steel in the United States, and return of the contaminated materials to Mexico. The incident resulted in significant radiation exposures within Mexico, but no known significant exposure within the United States. Response to the incident required the combined efforts of the Nuclear Regulatory Commission (NRC), Department of Energy, Department of Transportation, Department of State, and US Customs Service (Department of Treasury) personnel at the Federal level and representatives of all 50 State Radiation Control Programs and, in some instances, local and county government personnel. The response also required a diplomatic interface with the Mexican Government and cooperation of numerous commercial establishments and members of the general public. The report describes the factual information associated with the event and may serve as information for subsequent recommendations and actions by the NRC. 8 figures

Trace-element speciation and partitioning in environmental geochemistry and health

Energy Technology Data Exchange (ETDEWEB)

Farmer, J.G.; Gibson, M.J.; Lovell, M.A.

1983-09-01

Establishment of the chemical form and associations of trace elements is important in the scientifc and medical fields related to environmental geochemistry and health. Fundamental understanding of trace-element behavior, the realistic formulation of historical perspectives of trace-element contamination, an assessment of environmental transformation processes and a thorough appraisal of environment-related ill health and disease all depend on knowledge of the chemical speciation and partitioning of trace elements. These topics and the development of analytical speciation techniques and procedures are discussed with reference to trace-element studies in the Department of Forensic Medicine and Science, University of Glasgow, on lacustrine sediments and water, the atmosphere, soil and street dirt of an urban environment, and human biological fluids. 206 references, 4 figures.

Degradation of Nafion due to contamination from Swelling-Dehydration Cycles

DEFF Research Database (Denmark)

Andersen, Shuang Ma; Morgen, Per; Skou, Eivind Morten

degradation in direct methanol fuel cells (DMFCs), where liquid water has direct contact with the electrolyte. An ex-situ experiment was established with swelling-dehydration cycles on the membrane. However, formation of sulfonic anhydride was not detected during the entire treatment; instead contamination...... from traces calcium in the nominally pure water used in the experiment was found to be the primary reason for the deterioration of the membrane properties. Trace impurities in the liquid methanol feed in DMFC may therefore represent an important contamination source....

Gas dispersion concentration of trace inorganic contaminants from fuel gas and analysis using head-column field-amplified sample stacking capillary electrophoresis.

Science.gov (United States)

Yang, Jianmin; Li, Hai-Fang; Li, Meilan; Lin, Jin-Ming

2012-08-21

The presence of inorganic elements in fuel gas generally accelerates the corrosion and depletion of materials used in the fuel gas industry, and even leads to serious accidents. For identification of existing trace inorganic contaminants in fuel gas in a portable way, a highly efficient gas-liquid sampling collection system based on gas dispersion concentration is introduced in this work. Using the constructed dual path gas-liquid collection setup, inorganic cations and anions were simultaneously collected from real liquefied petroleum gas (LPG) and analyzed by capillary electrophoresis (CE) with indirect UV absorbance detection. The head-column field-amplified sample stacking technique was applied to improve the detection limits to 2-25 ng mL(-1). The developed collection and analytical methods have successfully determined existing inorganic contaminants in a real LPG sample in the range of 4.59-138.69 μg m(-3). The recoveries of cations and anions with spiked LPG samples were between 83.98 and 105.63%, and the relative standard deviations (RSDs) were less than 7.19%.

Underwater Coatings for Contamination Control

International Nuclear Information System (INIS)

Julia L. Tripp; Kip Archibald; Ann-Marie Phillips; Joseph Campbell

2004-01-01

The Idaho National Engineering and Environmental Laboratory (INEEL) is deactivating several fuel storage basins. Airborne contamination is a concern when the sides of the basins are exposed and allowed to dry during water removal. One way of controlling this airborne contamination is to fix the contamination in place while the pool walls are still submerged. There are many underwater coatings available on the market that are used in marine, naval and other applications. A series of tests were run to determine whether the candidate underwater fixatives are easily applied and adhere well to the substrates (pool wall materials) found in INEEL fuel pools. The four pools considered included (1) Test Area North (TAN-607) with epoxy painted concrete walls; (2) Idaho Nuclear Technology and Engineering Center (INTEC) (CPP-603) with bare concrete walls; (3) Materials Test Reactor (MTR) Canal with stainless steel lined concrete walls; and (4) Power Burst Facility (PBF-620) with stainless steel lined concrete walls on the bottom and epoxy painted carbon steel lined walls on the upper portions. Therefore, the four materials chosen for testing included bare concrete, epoxy painted concrete, epoxy painted carbon steel, and stainless steel. The typical water temperature of the pools varies from 55 F to 80 F dependent on the pool and the season. These tests were done at room temperature. The following criteria were used during this evaluation. The underwater coating must: (1) Be easy to apply; (2) Adhere well to the four surfaces of interest; (3) Not change or have a negative impact on water chemistry or clarity; (4) Not be hazardous in final applied form; and (5) Be proven in other underwater applications. In addition, it is desirable for the coating to have a high pigment or high cross-link density to prevent radiation from penetrating. This paper will detail the testing completed and the test results. A proprietary two-part, underwater epoxy owned by S. G. Pinney and Associates

HAIR HEAVY METAL AND ESSENTIAL TRACE ELEMENT CONCENTRATION IN CHILDREN WITH AUTISM SPECTRUM DISORDER.

Science.gov (United States)

Tabatadze, T; Zhorzholiani, L; Kherkheulidze, M; Kandelaki, E; Ivanashvili, T

2015-11-01

Our study aims evaluation of level of essential trace elements and heavy metals in the hair samples of children with autistic spectrum disorder (ASD) and identification of changes that are associated with autistic spectrum disorders. Case-control study was conducted at Child Development Center of Iashvili Children's Central Hospital (LD).We studied 60 children aged from 4 to 5 years old. The concentrations of 28 elements among (Ca,Zn, K, Fe, Cu, Se, Mn, Cr, S, Br, Cl, Co, Ag, V, Ni, Rb, Mo, Sr, Ti, Ba, Pb, As, Hg, Cd, Sb, Zr, Sn, Bi) them trace elements and toxic metals) were determined in scalp hair samples of children (n=30) with autistic spectrum disorder (ASD) and from control group of healthy children (n=30) with matched sex and age. Micro-elemental status was detected in the hair, with roentgen-fluorescence spectrometer method (Method MBИ 081/12-4502-000, Apparatus ALVAX- CIP, USA - UKRAIN) .To achieve the similarity of study and control groups, pre and postnatal as well as family and social history were assessed and similar groups were selected. Children with genetic problems, malnourished children, children from families with social problems were excluded from the study. The diagnosis of ASD were performed by pediatrician and psychologist (using M-CHAT and ADOS) according to DSM IV (Diagnostic and Statistical Manual of Mental Disorders from the American Psychiatric association) criteria. The study was statistically analyzed using computer program SPSS 19. Deficiencies of essential trace microelements revealed in both group, but there was significant difference between control and studied groups. The most deficient element was zinc (92% in target and 20% in control), then - manganese (55% and 8%) and selenium (38% and 4%). In case of cooper study revealed excess concentration of this element only in target group in 50% of cases. The contaminations to heavy metals were detected in case of lead (78% and 16), mercury (43% and 10%) and cadmium (38% and 8%). The

A multi-disciplinary approach to the removal of emerging contaminants in municipal wastewater treatment plans in New York State, 2003-2004

Science.gov (United States)

Philips, Patrick J.; Stinson, Beverley; Zaugg, Steven D.; Furlong, Edward T.; Kolpin, Dana W.; Esposito, Kathleen; Bodniewicz, B.; Pape, R.; Anderson, J.

2005-01-01

Across the United States, there is a rapidly growing awareness of the occurrence and the toxicological impacts of natural and synthetic trace compounds in the environment. These trace compounds, referred to as emerging contaminants (ECs), are reported to cause a range of negative impacts in the environment, such as adverse effects on biota in receiving streams and interference with the normal functions of the endocrine system, which controls growth and development in living organisms.

Assessment of trace metals in sewage water and sludge from River ...

African Journals Online (AJOL)

From the calculated individual contamination factors, Ni and Zn followed by Cd and Pb posed the highest risk to sewage water contamination. Based on this study, the human health is at risk, since sewage water from the drainage basin has been the source for irrigation water during dry seasons, which might lead to trace ...

Chronic exposure of ecosystems and public to elements in trace contributions; L'exposition chronique des ecosystemes et du public aux elements en traces contributions

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

The needs in radiation protection come towards the question of chronic contaminations by trace elements or radioactive compounds. The chronicity induces to take into account a whole of redistribution mechanisms more important than the only ways of the most direct transfer. In the case of environment, that is going to become one of the way of public contamination is a target to protect, the important work is to link the contamination situation to eventual consequences on the ecosystems situation. (N.C.)0.

Minimum detectable activities of contamination control survey equipment

International Nuclear Information System (INIS)

Goles, R.W.; Baumann, B.L.; Johnson, M.L.

1991-08-01

The Instrumentation ampersand External Dosimetry (I ampersand ED) Section of the Health Physics Department at the Pacific Northwest Laboratory (PNL) has performed a series of tests to determine the ability of portable survey instruments used at Hanford to detect radioactive contamination at levels required by DOE 5480.11. This semi-empirical study combines instrumental, statistical, and human factors as necessary to derive operational detection limits. These threshold detection values have been compared to existing contamination control requirements, and detection deficiencies have been identified when present. Portable survey instruments used on the Hanford Site identify the presence of radioactive surface contamination based on the detection of α-, β-, γ-, and/or x-radiation. However, except in some unique circumstances, most contamination monitors in use at Hanford are configured to detect either α-radiation alone or β- and γ-radiation together. Testing was therefore conducted on only these two categories of radiation detection devices. Nevertheless, many of the results obtained are generally applicable to all survey instruments, allowing performance evaluations to be extended to monitoring devices which are exclusively γ- and/or x-ray- sensitive. 6 figs., 2 tabs

Evaluation And Characterization Of Trace Metals Contamination In The Surface Sediment Using Pollution Load Index PLI And Geo-Accumulation Index Igeo Of Ona River Western Nigeria

Directory of Open Access Journals (Sweden)

Andem

2015-01-01

Full Text Available Abstract Evaluation and Characterization of Trace Metal Contamination in the Surface Sediment Using Pollution Load Index PLI and Geo-accumulation Index Igeo Index of Ona River was conducted for six months. From the result of this study the mean values of lead ranged between 0.004 mgkg and 0.330 mgkg while the mean iron was highest 5.05 mgkg in station 4 and lowest 2.26 mgkg in station 5. The mean chromium value ranged from 0.007 mgkg station 1 and 2 to 0.021 mgkg station 3 and 4. The mean copper was highest 3.97 mgkg in station 1 and lowest 0.008 mgkg in station 2. Analysis of variance ANOVA revealed the same trend in spatial variation of these heavy metals. There was a significant difference P 0.05 in lead chromium and copper among the study sampling stations and insignificant difference P0.05 in iron among the study sampling station. The PLI values recorded for all the stations were below 1. Thus the sediment of the study stretch that Ona River is unpolluted. The Igeo values for chromium and iron fall in class 0 in all the five sampling stations indicating that there is no pollution from these metals in the Ona River sediments lead fall in class 3 in station 4indicating moderately to heavily contaminated condition and class 0in station 1 2 3 and 5 and copper fall in class 3 in station 4 and 5 in class 6 in station 3 indicating extremely contaminated condition. The Igeo values were consistent with those derived for PLI. All trace metals had concentrations below the EPA regulatory limits for sediment except iron. From the results of this study sediment quality reflects the impacts of anthropogenic activities on quality of the river. However the continuous build-up of the metal contaminants can be checked if relevant government agencies ensure strict compliant of industrial standards which stipulate treatment of industrial waste before discharging such contaminated effluentswastes into River. Therefore perpetual assessment is highly recommended

Biodegradation: Updating the Concepts of Control for Microbial Cleanup in Contaminated Aquifers

DEFF Research Database (Denmark)

Meckenstock, Rainer U.; Elsner, Martin; Griebler, Christian

2015-01-01

Biodegradation is one of the most favored and sustainable means of removing organic pollutants from contaminated aquifers but the major steering factors are still surprisingly poorly understood. Growing evidence questions some of the established concepts for control of biodegradation. Here, we...... on the controls of biodegradation in contaminant plumes. These include the plume fringe concept, transport limitations, and transient conditions as currently underestimated processes affecting biodegradation....

Estuaries as filters: the role of tidal marshes in trace metal removal.

Directory of Open Access Journals (Sweden)

Johannes Teuchies

Full Text Available Flux calculations demonstrate that many estuaries are natural filters for trace metals. Yet, the underlying processes are poorly investigated. In the present study, it was hypothesized that intertidal marshes contribute significantly to the contaminant filter function of estuaries. Trace metal concentrations and sediment characteristics were measured along a transect from the subtidal, over an intertidal flat and marsh to a restored marsh with controlled reduced tide. Metal concentrations in the intertidal and restored marsh were found to be a factor two to five higher than values in the subtidal and intertidal flat sediments. High metal concentrations and high accretion rates indicate a high metal accumulation capacity of the intertidal marshes. Overbank sedimentation in the tidal marshes of the entire estuary was calculated to remove 25% to 50% of the riverine metal influx, even though marshes comprise less than 8% of the total surface of the estuary. In addition, the large-scale implementation of planned tidal marsh restoration projects was estimated to almost double the trace metal storage capacity of the present natural tidal marshes in the estuary.

Estuaries as Filters: The Role of Tidal Marshes in Trace Metal Removal

Science.gov (United States)

Teuchies, Johannes; Vandenbruwaene, Wouter; Carpentier, Roos; Bervoets, Lieven; Temmerman, Stijn; Wang, Chen; Maris, Tom; Cox, Tom J. S.; Van Braeckel, Alexander; Meire, Patrick

2013-01-01

Flux calculations demonstrate that many estuaries are natural filters for trace metals. Yet, the underlying processes are poorly investigated. In the present study, it was hypothesized that intertidal marshes contribute significantly to the contaminant filter function of estuaries. Trace metal concentrations and sediment characteristics were measured along a transect from the subtidal, over an intertidal flat and marsh to a restored marsh with controlled reduced tide. Metal concentrations in the intertidal and restored marsh were found to be a factor two to five higher than values in the subtidal and intertidal flat sediments. High metal concentrations and high accretion rates indicate a high metal accumulation capacity of the intertidal marshes. Overbank sedimentation in the tidal marshes of the entire estuary was calculated to remove 25% to 50% of the riverine metal influx, even though marshes comprise less than 8% of the total surface of the estuary. In addition, the large-scale implementation of planned tidal marsh restoration projects was estimated to almost double the trace metal storage capacity of the present natural tidal marshes in the estuary. PMID:23950927

Yeast Derived LysA2 Can Control Bacterial Contamination in Ethanol Fermentation

Directory of Open Access Journals (Sweden)

Jun-Seob Kim

2018-05-01

Full Text Available Contamination of fuel-ethanol fermentations continues to be a significant problem for the corn and sugarcane-based ethanol industries. In particular, members of the Lactobacillaceae family are the primary bacteria of concern. Currently, antibiotics and acid washing are two major means of controlling contaminants. However, antibiotic use could lead to increased antibiotic resistance, and the acid wash step stresses the fermenting yeast and has limited effectiveness. Bacteriophage endolysins such as LysA2 are lytic enzymes with the potential to contribute as antimicrobials to the fuel ethanol industries. Our goal was to evaluate the potential of yeast-derived LysA2 as a means of controlling Lactobacillaceae contamination. LysA2 intracellularly produced by Pichia pastoris showed activity comparable to Escherichia coli produced LysA2. Lactic Acid Bacteria (LAB with the A4α peptidoglycan chemotype (L-Lys-D-Asp crosslinkage were the most sensitive to LysA2, though a few from that chemotype were insensitive. Pichia-expressed LysA2, both secreted and intracellularly produced, successfully improved ethanol productivity and yields in glucose (YPD60 and sucrose-based (sugarcane juice ethanol fermentations in the presence of a LysA2 susceptible LAB contaminant. LysA2 secreting Sacharomyces cerevisiae did not notably improve production in sugarcane juice, but it did control bacterial contamination during fermentation in YPD60. Secretion of LysA2 by the fermenting yeast, or adding it in purified form, are promising alternative tools to control LAB contamination during ethanol fermentation. Endolysins with much broader lytic spectrums than LysA2 could supplement or replace the currently used antibiotics or the acidic wash.

Microbiological contamination in radiopharmacy: problems and implementation of controls in a step quality

International Nuclear Information System (INIS)

Maia, Serge; Nicol, Benoit; Rouleau, Annick; Guilloteau, Denis; Van der mee-marquet, Nathalie

2008-01-01

Microbiological contamination (bio-contamination) of the preparation room of injectable radiopharmaceutical drugs must be controlled to guarantee their sterility, but appears difficult to be obtained because of the principles related to the radioprotection of the staff. In order to fulfil the two requirements (sterility and radioprotection), the Radiopharmacy Unit of the University Hospital of Tours implemented a step quality including a system of Quality-Control, in 2004. Material and methods: This system contains, on the one hand, control of the sterility of preparations by direct sowing within culture mediums and, on the other hand, control of the bio-contamination of surfaces of the preparation room by tacking a swab on several representative points. Results: The bio-contamination of surfaces between 2004 and 2005 was frequent and did not stop increasing. After analysis of probable causes, new means of prevention came to supplement this step quality: application of new protocols for the bio-cleaning of surfaces; compliance with rules described in the Good Manufacturing Practices; a continuous formation of the personnel on the principles of hygiene. Thus, between 2005 and 2006, a significant fall of the bacterial colonies number (α < 0.05) and the disappearance of filamentous fungi were obtained. Discussion/Conclusion: This work shows the impact of the implementation of these controls on the microbiological contamination reduction in Radiopharmacy and on the improvement of a step quality. (authors) [fr

[Simulation on contamination forecast and control of groundwater in a certain hazardous waste landfill].

Science.gov (United States)

Ma, Zhi-Fei; An, Da; Jiang, Yong-Hai; Xi, Bei-Dou; Li, Ding-Long; Zhang, Jin-Bao; Yang, Yu

2012-01-01

On the basis of site investigation and data collection of a certain hazardous waste landfill, the groundwater flow and solute transport coupled models were established by applying Visual Modflow software, which was used to conduct a numerical simulation that forecast the transport process of Cr6+ in groundwater and the effects of three control measures (ground-harden, leakage-proof barriers and drainage ditches) of contaminants transport after leachate leakage happened in impermeable layer of the landfill. The results show that the contamination plume of Cr6+ transports with groundwater flow direction, the contamination rang would reach the pool's boundary in 10 years, and the distance of contamination transport is 1 450 m. But the diffusion range of contamination plume would not be obviously expanded between 10 and 20 years. While the ground is hardened, the contamination plume would not reach the pool's boundary in 20 years. When the leakage-proof barrier is set in the bottom of water table aquifer, the concentration of Cr6+ is higher than that the leakage-proof barrier is unset, but the result is just opposite when setting the leakage-proof barrier in the bottom of underlying aquifer. The range of contamination plume is effectively controlled by setting drainage ditches that water discharge is 2 642 m3 x d(-1), which makes the monitoring wells would not be contaminated in 20 years. Moreover, combining the ground-harden with drainage ditches can get the best effect in controlling contaminants diffusion, and meanwhile, the drainage ditches' daily discharge is reduced to 1 878 m3 x d(-1). Therefore, it is suggested that the control measure combining the ground-harden with drainage ditches should apply to prevent contamination diffusion in groundwater when leachate leakage have happened in impermeable layer of the landfill.

Enhanced Removal of Nutrients and Trace Organics from Urban Runoff with Novel Capture, Treatment, and Recharge Systems

Science.gov (United States)

Ashoori, N.; Planes, M. T.; Lefevre, G.; Sedlak, D.; Luthy, R. G.

2017-12-01

Rapid population growth, urban sprawl and impact of climate change are forcing water-stressed areas to rely on new local sources of water supply. Under this scenario, reclamation of stormwater runoff has emerged as a source for irrigation and replenishing drinking-water groundwater reservoirs. However, urban stormwater can be a significant source of pollutants, including nutrients and organic compounds. In order to overcome the stormwater treatment system limitations, this project has developed a pilot-scale column system for passive treatment of infiltrated water using low-cost, low-energy geomedia. The objective was to provide guidance on the design and operation of systems for controlling nutrient and trace organic contaminant releases to surface waters. The work comprised of replicate column studies in the field to test stormwater treatment modules with various media, such as woodchips and biochar, using urban runoff from a watershed in Sonoma, California. Woodchip bioreactors host an endemic population of microorganisms that can be harnessed to biologically degrade nitrate. The columns amended with biochar enhance removal of organic pollutants present in stormwater through physicochemical processes (i.e., adsorption onto biochar) and biodegradation in the column through increasing retention time. The field columns were conditioned with stormwater for eight months before being spiked weekly with 50 ppb of representative trace organics. The key finding was the successful field demonstration of a novel treatment system for both the removal of nitrate and trace organics. Nitrogen removal was successful in all columns for the thirteen month experiment due to the woodchips being an effective source of carbon for denitrifying microorganisms to convert nitrate to nitrogen gases. As for the trace organics experiments, the results highlight an overall attenuation of the studied trace organic compounds by the columns containing woodchip and biochar throughout the five

Identifying sources of groundwater pollution using trace element signatures

International Nuclear Information System (INIS)

Olmez, I.; Hayes, M.J.

1990-01-01

A simple receptor modeling approach has been applied to groundwater pollution studies and has shown that marker trace elements can be used effectively in source identification and apportionment. Groundwater and source materials from one coal-fired and five oil-fired power plants, and one coal-tar deposit site have been analyzed by instrumental neutron activation analysis for more than 20 minor and trace elements. In one of the oil-fired power plants, trace element patterns indicated a leak from the hazardous waste surface impoundments owing to the failure of a hypolon liner. Also, the extent and spatial distribution of groundwater contamination have been determined in a coal-tar deposit site

Soil contamination standards for protection of personnel

International Nuclear Information System (INIS)

Rittmann, P.D.

1998-01-01

The objective of this report is to recommend soil contamination levels that will ensure that radionuclide intakes by unprotected workers are likely to give internal doses below selected dose limits during the working year. The three internal dose limits are 1, 100, and 500 mrem per year. In addition, photon, beta, and alpha instrument readings are estimated for these soil concentration limits. Two exposure pathways are considered: the first is inhalation of resuspended dust and the second is ingestion of trace amounts of soil. In addition, radioactive decay and ingrowth of progeny during the year of exposure is included. External dose from the soil contamination is not included because monitoring and control of external exposures is carried out independently from internal exposures, which are the focus of this report. The methods used are similar to those used by Carbaugh and Bihl (1993) to set bioassay criteria for such workers

Soil contamination standards for protection of personnel

Energy Technology Data Exchange (ETDEWEB)

Rittmann, P.D.

1998-04-16

The objective of this report is to recommend soil contamination levels that will ensure that radionuclide intakes by unprotected workers are likely to give internal doses below selected dose limits during the working year. The three internal dose limits are 1, 100, and 500 mrem per year. In addition, photon, beta, and alpha instrument readings are estimated for these soil concentration limits. Two exposure pathways are considered: the first is inhalation of resuspended dust and the second is ingestion of trace amounts of soil. In addition, radioactive decay and ingrowth of progeny during the year of exposure is included. External dose from the soil contamination is not included because monitoring and control of external exposures is carried out independently from internal exposures, which are the focus of this report. The methods used are similar to those used by Carbaugh and Bihl (1993) to set bioassay criteria for such workers.

21 CFR 211.113 - Control of microbiological contamination.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Control of microbiological contamination. 211.113 Section 211.113 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Production and...

Quantification of surface contamination: principles and applications

International Nuclear Information System (INIS)

Vo-Dinh, T.

1982-01-01

The applications discussed in this paper underscore the usefulness and versatility of molecular luminescence spectroscopy as an efficient surface detection technique. The technique can be used not only as a qualitative characterization method, but also as a quantitative analytical tool to detect trace contaminants on surfaces. Recent advances in instrumentation and methodology have expanded the applicability of surface luminescence into many new problem areas. Trace organics are emphasized here

Microbial contamination control in fuels and fuel systems since 1980 - a review

Energy Technology Data Exchange (ETDEWEB)

Passman, Frederick J. [Biodeterioration Control Associates, Inc (United States)], email: fredp@biodeterioration-control.com

2011-07-01

This paper presents a review of microbial contamination control in fuel and fuel systems. Some examples of the biodeterioration of components of fuel systems are given. Root cause analysis (RCA) and modeling can help in condition monitoring of fuel systems. RCA is a systematic process that starts after symptoms become apparent and facilitates improvement. Modeling, by contrast, starts before the problem occurs and the objective is to improve understanding of the process. Some of the different areas creating risk due to the process are climate, microbiology, chemistry, maintenance, and engineering. Condition monitoring is explained in detail, using representative samples. Contamination control plays a very important role. Various aspects of microbial contamination control are design, inventory control, house keeping and remediation. These aspects are explained in detail, using various examples. Since the deterioration cost involved is very high, its is important to avoid this problem by reducing the quantity of water used and using better risk assessment models.

Cross contamination in dual inlet isotope ratio mass spectrometers

NARCIS (Netherlands)

Meijer, H.A.J.; Neubert, R.E.M.; Visser, G.H.

2000-01-01

Since the early days of geochemical isotope ratio mass spectrometry there has always been the problem of cross contamination, i.e. the contamination of the sample gas with traces of reference gas land vice versa) in a dual inlet system and the analyzer itself. This was attributable to valve leakages

Elemental analyses of goundwater: demonstrated advantage of low-flow sampling and trace-metal clean techniques over standard techniques

Science.gov (United States)

Creasey, C. L.; Flegal, A. R.

The combined use of both (1) low-flow purging and sampling and (2) trace-metal clean techniques provides more representative measurements of trace-element concentrations in groundwater than results derived with standard techniques. The use of low-flow purging and sampling provides relatively undisturbed groundwater samples that are more representative of in situ conditions, and the use of trace-element clean techniques limits the inadvertent introduction of contaminants during sampling, storage, and analysis. When these techniques are applied, resultant trace-element concentrations are likely to be markedly lower than results based on standard sampling techniques. In a comparison of data derived from contaminated and control groundwater wells at a site in California, USA, trace-element concentrations from this study were 2-1000 times lower than those determined by the conventional techniques used in sampling of the same wells prior to (5months) and subsequent to (1month) the collections for this study. Specifically, the cadmium and chromium concentrations derived using standard sampling techniques exceed the California Maximum Contaminant Levels (MCL), whereas in this investigation concentrations of both of those elements are substantially below their MCLs. Consequently, the combined use of low-flow and trace-metal clean techniques may preclude erroneous reports of trace-element contamination in groundwater. Résumé L'utilisation simultanée de la purge et de l'échantillonnage à faible débit et des techniques sans traces de métaux permet d'obtenir des mesures de concentrations en éléments en traces dans les eaux souterraines plus représentatives que les résultats fournis par les techniques classiques. L'utilisation de la purge et de l'échantillonnage à faible débit donne des échantillons d'eau souterraine relativement peu perturbés qui sont plus représentatifs des conditions in situ, et le recours aux techniques sans éléments en traces limite l

Chronic exposure of ecosystems and public to elements in trace contributions

International Nuclear Information System (INIS)

2004-01-01

The needs in radiation protection come towards the question of chronic contaminations by trace elements or radioactive compounds. The chronicity induces to take into account a whole of redistribution mechanisms more important than the only ways of the most direct transfer. In the case of environment, that is going to become one of the way of public contamination is a target to protect, the important work is to link the contamination situation to eventual consequences on the ecosystems situation. (N.C.)

Hyperspectral to multispectral imaging for detection of tree nuts and peanut traces in wheat flour

Directory of Open Access Journals (Sweden)

Puneet Mishra

2015-06-01

Full Text Available In current industrial environments there is an increasing need for practical and inexpensive quality control systems to detect the foreign food materials in powder food processing lines. This demand is especially important for the detection of product adulteration with traces of highly allergenic products, such as peanuts and tree nuts. Manufacturing industries dealing with the processing of multiple powder food products present a substantial risk for the contamination of powder foods with traces of tree nuts and other adulterants, which might result in unintentional ingestion of nuts by the sensitised population. Hence, the need for an in-line system to detect nut traces at the early stages of food manufacturing is of crucial importance. In this present work, a feasibility study of a spectral index for revealing adulteration of tree nut and peanut traces in wheat flour samples with hyperspectral images is reported. The main nuts responsible for allergenic reactions considered in this work were peanut, hazelnut and walnut. Enhanced contrast between nuts and wheat flour was obtained after the application of the index. Furthermore, the segmentation of these images by selecting different thresholds for different nut and flour mixtures allowed the identification of nut traces in the samples. Pixels identified as nuts were counted and compared with the actual percentage of peanut adulteration. As a result, the multispectral system was able to detect and provide good visualisation of tree nut and peanut trace levels down to 0.01% by weight. In this context, multispectral imaging could operate in conjuction with chemical procedures, such as Real Time Polymerase Chain Reaction and Enzyme-Linked Immunosorbent Assay to save time, money and skilled labour on product quality control. This approach could enable not only a few selected samples to be assessed but also to extensively incorporate quality control surveyance on product processing lines.

Effect of organic acids traces on the carbon steel corrosion behavior

International Nuclear Information System (INIS)

Stefanescu, D.; Radulescu; Mogosan, S.

2009-01-01

There are many different ways in which organic matter may get in water-steam cycles. One important pathway is constituted by organic matter admitted into the system by chemical make-up water under standard operation conditions (without inverse osmosis). The high molecular weight organic matter, in particularly polysaccharides are broken in organic acids, in particular acetic and formic acid. This paper presents an overview of the investigations undertaken referring to the behavior SA106 gr. B mild steel in secondary circuit aqueous environment contaminated with formic and acetic acid traces. The samples were filmed in static autoclaves in operation conditions of secondary circuit, in contaminated environment and after that they were investigated using metallographic microscopy and SEM. In addition, an electrochemical technique videlicet impedance spectroscopy (EIS) was used to investigate the corrosion behavior of SA106 gr. B carbon steel in secondary circuit medium contaminated with formic and acetic acid traces. (authors)

Proceedings of the 6. International Conference on the Biogeochemistry of Trace Elements. CD ed.

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

This international conference provided a forum for researchers from around the world to exchange research notes of subjects dealing with the biogeochemistry of trace elements. The conference proceedings included 456 papers, of which 34 have been indexed separately for inclusion in the database. Each presentation included an introduction to a study, materials and methods, results and discussion and a conclusion. The conference was divided into special oral symposia (SO), general oral sessions (GO), a special poster session (SP) and a general poster session (GP). A wide range of topics were presented including: biosorption of trace elements and the bioavailability of metals for uptake and effects; chemical remediation; adsorption reactions on soils and sediments; fractionation of metals in soils; diagenetic transformations; arsenic content and distribution; metal speciation; the role of metal-organic interactions; phytoremediation; contents and distribution in soils and waters; soil amendments; mercury and human and animal health; mercury in the environment; aqueous speciation; phyto-, microbial and chemical remediation tools for metal contaminated soils and groundwater; geochemical surface controls on trace element fate; temporal trends of trace metals in biota; biomonitoring; transport in soils and waters; analytical techniques; metal/mineral interactions with microorganisms; the chemistry of trace elements in fly ash; ecotoxicology; groundwater; and, soil amendments. refs., tabs., figs.

Contamination of crop vegetation with trace elements from a fertilizer plant. An INAA study

International Nuclear Information System (INIS)

Pantelica, A.; Oprea, C.; Frontasyeva, M.; Georgescu, I.I.; Pincovschi, E.; Catana, L.

2004-01-01

Instrumental neutron activation analysis (INAA) was used to determine various trace elements in crop vegetation (potato, carrot and maize) grown around a phosphate fertilizer plant in Romania. INAA using long-lived radionuclides was applied at NIPNE in Bucharest, and based on short-lived radionuclides at JINR in Dubna. The results for Na, Mg, Cl, K, Ca, Mn, Fe, Zn, As, and Hg were compared with Romanian norms for the alimentary products, as well as with literature data. Concentration ratios to control samples for both soil and crop as well as concentration factors of crop to host soil were assessed. (author)

assessment of trace metals contamination of soils around some ...

African Journals Online (AJOL)

ABSTRACT. This study was carried out to determine the level of soil contamination by metals around some automobile mechanic .... and this was done all through the sample preparation. ... shaking was done by a mechanical sieve shaker and.

Trace Elements in Parenteral Nutrition: Considerations for the Prescribing Clinician.

Science.gov (United States)

Jin, Jennifer; Mulesa, Leanne; Carrilero Rouillet, Mariana

2017-04-28

Trace elements (TEs) are an essential component of parenteral nutrition (PN). Over the last few decades, there has been increased experience with PN, and with this knowledge more information about the management of trace elements has become available. There is increasing awareness of the effects of deficiencies and toxicities of certain trace elements. Despite this heightened awareness, much is still unknown in terms of trace element monitoring, the accuracy of different assays, and current TE contamination of solutions. The supplementation of TEs is a complex and important part of the PN prescription. Understanding the role of different disease states and the need for reduced or increased doses is essential. Given the heterogeneity of the PN patients, supplementation should be individualized.

Contamination control methods for gases used in the microlithography process

Science.gov (United States)

Rabellino, Larry; Applegarth, Chuck; Vergani, Giorgio

2002-07-01

Sensitivity to contamination continues to increase as the technology shrinks from 365 nm I-line lamp illumination to 13.4 nm Extreme Ultraviolet laser activated plasma. Gas borne impurities can be readily distributed within the system, remaining both suspended in the gas and attached to critical surfaces. Effects from a variety of contamination, some well characterized and others not, remain a continuing obstacle for stepper manufacturers and users. Impurities like oxygen, moisture and hydrocarbons in parts per billion levels can absorb light, reducing the light intensity and subsequently reducing the consistence of the process. Moisture, sulfur compounds, ammonia, acid compounds and organic compounds such as hydrocarbons can deposit on lens or mirror surfaces affecting image quality. Regular lens replacement or removal for cleaning is a costly option and in-situ cleaning processes must be carefully managed to avoid recontamination of the system. The contamination can come from outside the controlled environment (local gas supply, piping system, & leaks), or from the materials moving into the controlled environment; or contamination may be generated inside the controlled environment as a result of the process itself. The release of amines can occur as a result of the degassing of the photo-resists. For the manufacturer and user of stepper equipment, the challenge is not in predictable contamination, but the variable or unpredictable contamination in the process. One type of unpredictable contamination may be variation in the environmental conditions when producing the nitrogen gas and Clean Dry Air (CDA). Variation in the CDA, nitrogen and xenon may range from parts per billion to parts per million. The risk due to uncontrolled or unmonitored variation in gas quality can be directly related to product defects. Global location can significantly affect the gas quality, due to the ambient air quality (for nitrogen and CDA), production methods, gas handling equipment

Microbial community structure and activity in trace element-contaminated soils phytomanaged by Gentle Remediation Options (GRO).

Science.gov (United States)

Touceda-González, M; Prieto-Fernández, Á; Renella, G; Giagnoni, L; Sessitsch, A; Brader, G; Kumpiene, J; Dimitriou, I; Eriksson, J; Friesl-Hanl, W; Galazka, R; Janssen, J; Mench, M; Müller, I; Neu, S; Puschenreiter, M; Siebielec, G; Vangronsveld, J; Kidd, P S

2017-12-01

Gentle remediation options (GRO) are based on the combined use of plants, associated microorganisms and soil amendments, which can potentially restore soil functions and quality. We studied the effects of three GRO (aided-phytostabilisation, in situ stabilisation and phytoexclusion, and aided-phytoextraction) on the soil microbial biomass and respiration, the activities of hydrolase enzymes involved in the biogeochemical cycles of C, N, P, and S, and bacterial community structure of trace element contaminated soils (TECS) from six field trials across Europe. Community structure was studied using denaturing gradient gel electrophoresis (DGGE) fingerprinting of Bacteria, α- and β-Proteobacteria, Actinobacteria and Streptomycetaceae, and sequencing of DGGE bands characteristic of specific treatments. The number of copies of genes involved in ammonia oxidation and denitrification were determined by qPCR. Phytomanagement increased soil microbial biomass at three sites and respiration at the Biogeco site (France). Enzyme activities were consistently higher in treated soils compared to untreated soils at the Biogeco site. At this site, microbial biomass increased from 696 to 2352 mg ATP kg -1 soil, respiration increased from 7.4 to 40.1 mg C-CO 2 kg -1 soil d -1 , and enzyme activities were 2-11-fold higher in treated soils compared to untreated soil. Phytomanagement induced shifts in the bacterial community structure at both, the total community and functional group levels, and generally increased the number of copies of genes involved in the N cycle (nirK, nirS, nosZ, and amoA). The influence of the main soil physico-chemical properties and trace element availability were assessed and eventual site-specific effects elucidated. Overall, our results demonstrate that phytomanagement of TECS influences soil biological activity in the long term. Copyright © 2017 Elsevier Ltd. All rights reserved.

Muscarinic receptors in amygdala control trace fear conditioning.

Directory of Open Access Journals (Sweden)

Amber N Baysinger

Full Text Available Intelligent behavior requires transient memory, which entails the ability to retain information over short time periods. A newly-emerging hypothesis posits that endogenous persistent firing (EPF is the neurophysiological foundation for aspects or types of transient memory. EPF is enabled by the activation of muscarinic acetylcholine receptors (mAChRs and is triggered by suprathreshold stimulation. EPF occurs in several brain regions, including the lateral amygdala (LA. The present study examined the role of amygdalar mAChRs in trace fear conditioning, a paradigm that requires transient memory. If mAChR-dependent EPF selectively supports transient memory, then blocking amygdalar mAChRs should impair trace conditioning, while sparing delay and context conditioning, which presumably do not rely upon transient memory. To test the EPF hypothesis, LA was bilaterally infused, prior to trace or delay conditioning, with either a mAChR antagonist (scopolamine or saline. Computerized video analysis quantified the amount of freezing elicited by the cue and by the training context. Scopolamine infusion profoundly reduced freezing in the trace conditioning group but had no significant effect on delay or context conditioning. This pattern of results was uniquely anticipated by the EPF hypothesis. The present findings are discussed in terms of a systems-level theory of how EPF in LA and several other brain regions might help support trace fear conditioning.

Muscarinic receptors in amygdala control trace fear conditioning.

Science.gov (United States)

Baysinger, Amber N; Kent, Brianne A; Brown, Thomas H

2012-01-01

Intelligent behavior requires transient memory, which entails the ability to retain information over short time periods. A newly-emerging hypothesis posits that endogenous persistent firing (EPF) is the neurophysiological foundation for aspects or types of transient memory. EPF is enabled by the activation of muscarinic acetylcholine receptors (mAChRs) and is triggered by suprathreshold stimulation. EPF occurs in several brain regions, including the lateral amygdala (LA). The present study examined the role of amygdalar mAChRs in trace fear conditioning, a paradigm that requires transient memory. If mAChR-dependent EPF selectively supports transient memory, then blocking amygdalar mAChRs should impair trace conditioning, while sparing delay and context conditioning, which presumably do not rely upon transient memory. To test the EPF hypothesis, LA was bilaterally infused, prior to trace or delay conditioning, with either a mAChR antagonist (scopolamine) or saline. Computerized video analysis quantified the amount of freezing elicited by the cue and by the training context. Scopolamine infusion profoundly reduced freezing in the trace conditioning group but had no significant effect on delay or context conditioning. This pattern of results was uniquely anticipated by the EPF hypothesis. The present findings are discussed in terms of a systems-level theory of how EPF in LA and several other brain regions might help support trace fear conditioning.

Regulatory control in the rehabilitation of contaminated sites in Syria

International Nuclear Information System (INIS)

Shweikani, R.; Suman, H.

2002-01-01

The work described in this paper is concerning the regulatory control set by the Atomic Energy Commission of Syria (AECS) for the contaminated sites with Naturally Occurring Radioactive Materials (NORM) in the oil industries in the northeast of Syria. These sites lie in a desert region with poor population density and low occupancy. The decision was made to use the activity concentration of 226 Ra per unit mass as a measure to identify the need for cleanup. Two limits were set for this purpose so that contamination concentration above the higher limit is defined as waste that has to be excavated from the site, while contamination concentration between the two limits can be dealt with on site. Contamination concentration below the lower limit was looked at as acceptable. Remediation plan to transfer the contaminated soil, with radium concentration over the higher limit, to an engineered disposal pit was adopted. Proper stabilisation measures and environmental monitoring programme were requested by the AECS and considered as essential parts of the remediation plan. (author)

Source apportionment of trace metals in river sediments: A comparison of three methods

International Nuclear Information System (INIS)

Chen, Haiyang; Teng, Yanguo; Li, Jiao; Wu, Jin; Wang, Jinsheng

2016-01-01

Increasing trace metal pollution in river sediment poses a significant threat to watershed ecosystem health. Identifying potential sources of sediment metals and apportioning their contributions are of key importance for proposing prevention and control strategies of river pollution. In this study, three advanced multivariate receptor models, factor analysis with nonnegative constraints (FA-NNC), positive matrix factorization (PMF), and multivariate curve resolution weighted-alternating least-squares (MCR-WALS), were comparatively employed for source apportionment of trace metals in river sediments and applied to the Le'an River, a main tributary of Poyang Lake which is the largest freshwater lake in China. The pollution assessment with contamination factor and geoaccumulation index suggested that the river sediments in Le'an River were contaminated severely by trace metals due to human activities. With the three apportionment tools, similar source profiles of trace metals in sediments were extracted. Especially, the MCR-WALS and PMF models produced essentially the same results. Comparatively speaking, the weighted schemes might give better solutions than the unweighted FA-NNC because the uncertainty information of environmental data was considered by PMF and MCR-WALS. Anthropogenic sources were apportioned as the most important pollution sources influencing the sediment metals in Le'an River with contributions of about 90%. Among them, copper tailings occupied the largest contribution (38.4–42.2%), followed by mining wastewater (29.0–33.5%), and agricultural activities (18.2–18.7%). To protect the ecosystem of Le'an River and Poyang Lake, special attention should be paid to the discharges of mining wastewater and the leachates of copper tailing ponds in that region. - Highlights: • Three advanced receptor models were comparatively employed for source apportionment. • The MCR-WALS and PMF models produce essentially same source profiles. • Copper

[The balance of harmful trace contaminants between the air humidity condensate and air in a simulator of the Mir orbit station moisture condensation unit].

Science.gov (United States)

Zlotopol'skiĭ, V M; Smolenskaia, T S

2000-01-01

Subject of the investigation was the balance of harmful trace contaminants (HTC) between the air moisture condensate and air in a simulator of the MIR moisture condensation unit. Experiments involved various classes of water-solvent compounds including alcohols (C1-C4), ketons (C1-C2), aldehydes (C1-C2), fatty acids (C2-C4), esters (acetates C4-C6), and ammonium. For most of the compounds, removal efficiency correlates with air humidity and virtually does not depend on the HTC concentration within the range of 0.25 to 59.1 mg/m3.

Phytoremediation trials on metal- and arsenic-contaminated pyrite wastes (Torviscosa, Italy)

Energy Technology Data Exchange (ETDEWEB)

Vamerali, Teofilo [Department of Environmental Sciences, University of Parma, Viale G.P. Usberti 11/A, 43100 Parma (Italy)], E-mail: teofilo.vamerali@unipd.it; Bandiera, Marianna; Coletto, Lucia; Zanetti, Federica [Department of Environmental Agronomy and Crop Sciences, University of Padova, Viale dell' Universita 16, 35020 Legnaro - Padova (Italy); Dickinson, Nicholas M. [Faculty of Science, Liverpool John Moores University, Byrom Street, Liverpool, L3 3AF (United Kingdom); Mosca, Giuliano [Department of Environmental Agronomy and Crop Sciences, University of Padova, Viale dell' Universita 16, 35020 Legnaro - Padova (Italy)

2009-03-15

At a site in Udine, Italy, a 0.7 m layer of As, Co, Cu, Pb and Zn contaminated wastes derived from mineral roasting for sulphur extraction had been covered with an unpolluted 0.15 m layer of gravelly soil. This study investigates whether woody biomass phytoremediation is a realistic management option. Comparing ploughing and subsoiling (0.35 m depth), the growth of Populus and Salix and trace element uptake were investigated in both pot and field trials. Species differences were marginal and species selection was not critical. Impaired above-ground productivity and low translocation of trace elements showed that bioavailable contaminant stripping was not feasible. The most significant finding was of coarse and fine roots proliferation in surface layers that provided a significant sink for trace elements. We conclude that phytostabilisation and effective immobilisation of metals and As could be achieved at the site by soil amelioration combined with woody species establishment. Confidence to achieve a long-term and sustainable remediation requires a more complete quantification of root dynamics and a better understanding of rhizosphere processes. - In As- and metal-contaminated pyrite wastes, contaminant stripping is not feasible, and root foraging and quantification of root dynamics holds the key to stabilisation in woody species.

Phytoremediation trials on metal- and arsenic-contaminated pyrite wastes (Torviscosa, Italy)

International Nuclear Information System (INIS)

Vamerali, Teofilo; Bandiera, Marianna; Coletto, Lucia; Zanetti, Federica; Dickinson, Nicholas M.; Mosca, Giuliano

2009-01-01

At a site in Udine, Italy, a 0.7 m layer of As, Co, Cu, Pb and Zn contaminated wastes derived from mineral roasting for sulphur extraction had been covered with an unpolluted 0.15 m layer of gravelly soil. This study investigates whether woody biomass phytoremediation is a realistic management option. Comparing ploughing and subsoiling (0.35 m depth), the growth of Populus and Salix and trace element uptake were investigated in both pot and field trials. Species differences were marginal and species selection was not critical. Impaired above-ground productivity and low translocation of trace elements showed that bioavailable contaminant stripping was not feasible. The most significant finding was of coarse and fine roots proliferation in surface layers that provided a significant sink for trace elements. We conclude that phytostabilisation and effective immobilisation of metals and As could be achieved at the site by soil amelioration combined with woody species establishment. Confidence to achieve a long-term and sustainable remediation requires a more complete quantification of root dynamics and a better understanding of rhizosphere processes. - In As- and metal-contaminated pyrite wastes, contaminant stripping is not feasible, and root foraging and quantification of root dynamics holds the key to stabilisation in woody species

Evaluation of trace elements contamination in cloud/fog water at an elevated mountain site in Northern China.

Science.gov (United States)

Liu, Xiao-huan; Wai, Ka-ming; Wang, Yan; Zhou, Jie; Li, Peng-hui; Guo, Jia; Xu, Peng-ju; Wang, Wen-xing

2012-07-01

Totally 117 cloud/fog water samples were collected at the summit of Mt. Tai (1534m a.s.l.)-the highest mountain in the Northern China Plain. The results were investigated by a combination of techniques including back trajectory model, regional air quality and dust storm models, satellite observations and Principal Component Analysis. Elemental concentrations were determined by Inductively Coupled Plasma Mass Spectrometry, with stringent quality control measures. Higher elemental concentrations were found at Mt. Tai compared with those reported by other overseas studies. The larger proportions and higher concentrations of toxic elements such as Pb and As in cloud/fog water compared with those in rainwater at Mt. Tai suggests higher potential hazards of cloud/fog water as a source of contamination in polluted areas to the ecosystem. Peak concentrations of trace elements were frequently observed during the onset of cloud/fog events when liquid water contents of cloud/fog water were usually low and large amount of pollutants were accumulated in the ambient air. Inverse relationship between elemental concentrations and liquid water contents were only found in the samples with high electrical conductivities and liquid water contents lower than 0.3gm(-3). Affected mainly by the emissions of steel industries and mining activities, air masses transported from south/southwest of Mt. Tai were frequently associated with higher elemental concentrations. The element Mn is attributed to play an important role in the acidity of cloud/fog water. The composition of cloud/fog water influenced by an Asian dust storm event was reported, which was seldom found in the literature. Copyright © 2012 Elsevier Ltd. All rights reserved.

Trace element phytoextraction from contaminated soil: a case study under Mediterranean climate.

Science.gov (United States)

Guidi Nissim, Werther; Palm, Emily; Mancuso, Stefano; Azzarello, Elisa

2018-03-01

The current field study aims to assess the suitability of four different plant species (i.e. poplar, willow, hemp and alfalfa) to be used for trace element (TE) (i.e. Cd, Cu, Ni, Pb and Zn) phytoextraction under hot-arid Mediterranean climate conditions. Plants were grown for two consecutive years on a moderate TE contaminated soil, supplied with water and mineral nutrients. The growth and physiological parameters were assessed throughout the trial to compare the response of plants to the environmental pollution, and TE uptake rates were measured for aboveground plant tissues. The phytoextraction rate for each species was expressed as a function of aboveground biomass yield and the TE uptake and translocation within the plant. Alfalfa played a significant role in reducing extractable Ni (60.6%) and Zn (46%) in the soil, whereas hemp reduced 32% of extractable Cd and 46% of extractable Pb; poplar decreased extractable Cd (37%), Ni (49%), Pb (46%) and Zn (63%); and willow reduced the extractable Zn (73%) compared to the beginning of the trial. No change in total TE content was observed; however, poplar and willow were able to extract and accumulate the highest amount of Zn (3200 and 5200 g ha -1  year -1 respectively) and Cu (182 and 116 g ha -1  year -1 ), whereas hemp, with 36 g ha -1  year -1 , showed the best phytoextraction potential for Pb. Overall, we found a positive correlation between the phytoextraction rate and biomass yield, extractable TE concentration and translocation factor (TF) and a negative relationship with Ca concentration in the soil.

Heavy metals and related trace elements

International Nuclear Information System (INIS)

Leland, H.V.; Luoma, S.N.; Wilkes, D.J.

1977-01-01

A review is given of heavy metals and related trace elements in the aquatic environment. Other reviews and bibliographies are cited, dealing with the metabolism and transport of metal ions and with the toxic effects of stable and radioactive trace metals on aquatic organisms. The sources of trace elements in natural waters are discussed. It is suggested that atmospheric inputs of several trace metals comprise sizable fractions of total inputs to the Great Lakes and continental shelf waters. Information on stack emissions of trace elements from a coal-fired steam plant was used to estimate the likely range of air concentrations and inputs to a forested watershed in Tennessee. Some basic concepts of cycling of elements through aquatic communities were examined, such as the Pb, Mn and Zn concentrations in sediment and estuarine plants and animals colonizing dredge-spoil disposal areas. The use of plants as biological indicators of trace element contamination was outlined, as well as bioaccumulation in aquatic fauna. The effects of environmental factors on the kinetics of element exchange were noted, for example the influx rates of Cs 137 in tubificid worms, and Co 60 and Zn 65 in shrimp were shown to be temperature dependent. The toxicity of heavy metals on aquatic fauna was discussed, such as the histopathological lesions in the kidney and liver of fishes caused by heavy metals, and the effects of Hg and Cu on the olfactory response of rainbow trout

Trace element analysis in rheumatoid arthritis under chrysotherapy

International Nuclear Information System (INIS)

Lecomte, R.; Paradis, P.; Monaro, S.; Barrette, M.; Lamoureux, G.; Menard, H.A.

1981-01-01

Proton induced X-ray emission (PIXE) analysis is used to measure trace element concentrations in blood serum from patients with rheumatoid arthritis. Initially trace element contaminations in blood-collecting and storing devices are determined. Then mean values and nyctemeral cycles are measured both in normal subjects and patients with rheumatoid arthritis and other similar pathologies. Abnormal concentrations of Cu and Zn and anomalies in the nyctemeral cycle are found in the patients. In the second phase of the project, the special case of chrysotherapeutically treated (gold salt treatment) rheumatoid arthritis patients is studied for extended periods of time (up to 53 weeks). (orig.)

Assessment of dietary intake of trace elements through Pakistani integrated diets

International Nuclear Information System (INIS)

Qureshi, I.H.; Mannan, A.; Waheed, S.; Rehman, S.; Ahmad, S.

1994-01-01

A research study related to the determination and assessment of essential and potentially toxic trace elements in Pakistani integrated diets was undertaken at PINSTECH from 1986-90 under the International Atomic Energy Agency (IAEA) Co-ordinated Research Programme (CRP). During this period eight different integrated human diets of the residents of the Islamabad and Gujranwala were prepared by taking into consideration their respective food habits in summer and winter seasons. Instrumental as well as radiochemical neutron activation analyses in combination with the atomic absorption spectrometry were utilized for the precise and accurate determination of up to 23 elements in the diet samples. This work has helped us obtain the base line values for studying trace elements nutrition, inadequacy, imbalances and toxicity. Further, this would help, in future, to monitor the degree of contamination from foreign chemicals. The weekly dietary intake values were calculated which showed that our foods contain fairly adequate quantity of essential trace elements. The diet samples analyzed showed no contamination level to an extent to cause an adverse impact on human health. (author). 23 refs, 5 figs, 21 tabs

Colombian legislation for air contamination control

International Nuclear Information System (INIS)

Hernandez S, Gildardo; Montes de Correa, Consuelo

1999-01-01

The most relevant legislative acts promulgated by the Colombian government for controlling atmospheric pollution are reviewed in chronological order. Special emphasis is paid to decree 948 of 1995 modified according to decree 2107 of 1995, e. The general dispositions about norms of air quality, emission levels, contaminant emissions, noise and offensive odors (chapter II), as well as, prohibitions and restrictions to emissions and noise from stationary and mobile sources (chapters III-V) furthermore, the resolutions issued so far by the ministry of the environment for regulating decree 948/95 in those aspects related to the prevention and control of atmospheric pollution are describes. Finally, the main philosophies for regulating air pollutants around the world are explained: the emissions norms, air quality norms, the emission taxes philosophy and the cost-benefit norms

Contamination Control and Monitoring of Tap Water as Fluid in Industrial Tap Water Hydraulic Systems

DEFF Research Database (Denmark)

Conrad, Finn; Adelstorp, Anders

1998-01-01

Presentation of results and methods addressed to contamination control and monitoring of tap water as fluid in tap water hydraulic systems.......Presentation of results and methods addressed to contamination control and monitoring of tap water as fluid in tap water hydraulic systems....

Assessment of trace metal contamination of soils around Oluyole ...

African Journals Online (AJOL)

This study was carried out to determine the level of metals contamination of the soils around Oluyole industrial estate in Ibadan. Oluyole industrial estate has heavy concentration of manufacturing industries that generate a lot of waste products capable of introducing metals into the environment. Consequently, twenty-one ...

Assessment of trace metals contamination of soils around some ...

African Journals Online (AJOL)

This study was carried out to determine the level of soil contamination by metals around some automobile mechanic workshops in Oyo town in order to assess their possible adverse health implications on man and his environment. Concentrations of metals above certain levels have been shown to impair man's health.

CERES: a model of forest stand biomass dynamics for predicting trace contaminant, nutrient, and water effects. I. Model description

Energy Technology Data Exchange (ETDEWEB)

Dixon, K R; Luxmoore, R J; Begovich, C L

1978-06-01

CERES is a forest stand growth model which incorporates sugar transport in order to predict both short-term effects and long-term accumulation of trace contaminants and/or nutrients when coupled with the soil chemistry model (SCHEM), and models of solute uptake (DIFMAS and DRYADS) of the Unified Transport Model, UTM. An important feature of CERES is its ability to interface with the soil--plant--atmosphere water model (PROSPER) as a means of both predicting and studying the effects of plant water status on growth and solute transport. CERES considers the biomass dynamics of plants, standing dead and litter with plants divided into leaves, stems, roots, and fruits. The plant parts are divided further into sugar substrate, storage, and in the case of stems and roots, heartwood components. Each ecosystem omponent is described by a mass balance equation written as a first-order ordinary differential equation.

Contamination by arsenic and other trace elements in tube-well water and its risk assessment to humans in Hanoi, Vietnam

International Nuclear Information System (INIS)

Agusa, Tetsuro; Kunito, Takashi; Fujihara, Junko; Kubota, Reiji; Minh, Tu Binh; Kim Trang, Pham Thi; Iwata, Hisato; Subramanian, Annamalai; Viet, Pham Hung; Tanabe, Shinsuke

2006-01-01

Concentrations of As and other trace elements and their association were examined in groundwater (n=25) and human hair (n=59) collected at Gia Lam District and Thanh Tri District, suburban areas of Hanoi, Vietnam, in September 2001. Concentrations of As in the groundwater ranged from <0.10 to 330 μg/l, with about 40% of these exceeding WHO drinking water guideline of 10 μg/l. Also, 76% and 12% of groundwater samples had higher concentrations of Mn and Ba than WHO drinking water guidelines, respectively. Arsenic concentrations in hair of residents in Gia Lam and Thanh Tri Districts (range 0.088-2.77 μg/g dry wt.) were lower than those in other As-contaminated areas of the world, but were higher than those of people in non-contaminated areas. Concentrations of As and Mn in hair of some individuals from the Gia Lam and Thanh Tri Districts exceeded the level associated with their toxicity and, therefore, a potential health risk of As and Mn is a concern for the people consuming the contaminated water in this area. Cumulative As exposure was estimated to be lower than the threshold levels at the present, which might explain the absence of manifestations of chronic As poisoning and arsenicosis in the residents of Gia Lam and Thanh Tri Districts. To our knowledge, this study revealed for the first time that the residents are exposed not only to As but also Mn and Ba from groundwater in the Red River Delta, Vietnam. - High concentrations of arsenic, manganese and barium were found in tube-well water and human hair in suburban areas of Hanoi, Vietnam

Pollution Status of Pakistan: A Retrospective Review on Heavy Metal Contamination of Water, Soil, and Vegetables

Directory of Open Access Journals (Sweden)

Amir Waseem

2014-01-01

Full Text Available Trace heavy metals, such as arsenic, cadmium, lead, chromium, nickel, and mercury, are important environmental pollutants, particularly in areas with high anthropogenic pressure. In addition to these metals, copper, manganese, iron, and zinc are also important trace micronutrients. The presence of trace heavy metals in the atmosphere, soil, and water can cause serious problems to all organisms, and the ubiquitous bioavailability of these heavy metal can result in bioaccumulation in the food chain which especially can be highly dangerous to human health. This study reviews the heavy metal contamination in several areas of Pakistan over the past few years, particularly to assess the heavy metal contamination in water (ground water, surface water, and waste water, soil, sediments, particulate matter, and vegetables. The listed contaminations affect the drinking water quality, ecological environment, and food chain. Moreover, the toxicity induced by contaminated water, soil, and vegetables poses serious threat to human health.

Review of Trace-Element Field-Blank Data Collected for the California Groundwater Ambient Monitoring and Assessment (GAMA) Program, May 2004-January 2008

Science.gov (United States)

Olsen, Lisa D.; Fram, Miranda S.; Belitz, Kenneth

2010-01-01

Trace-element quality-control samples (for example, source-solution blanks, field blanks, and field replicates) were collected as part of a statewide investigation of groundwater quality in California, known as the Priority Basins Project of the Groundwater Ambient Monitoring and Assessment (GAMA) Program. The GAMA Priority Basins Project is being conducted by the U.S. Geological Survey (USGS) in cooperation with the California State Water Resources Control Board (SWRCB) to assess and monitor the quality of groundwater resources used for drinking-water supply and to improve public knowledge of groundwater quality in California. Trace-element field blanks were collected to evaluate potential bias in the corresponding environmental data. Bias in the environmental data could result from contamination in the field during sample collection, from the groundwater coming into contact with contaminants on equipment surfaces or from other sources, or from processing, shipping, or analyzing the samples. Bias affects the interpretation of environmental data, particularly if any constituents are present solely as a result of extrinsic contamination that would have otherwise been absent from the groundwater that was sampled. Field blanks were collected, analyzed, and reviewed to identify and quantify extrinsic contamination bias. Data derived from source-solution blanks and laboratory quality-control samples also were considered in evaluating potential contamination bias. Eighty-six field-blank samples collected from May 2004 to January 2008 were analyzed for the concentrations of 25 trace elements. Results from these field blanks were used to interpret the data for the 816 samples of untreated groundwater collected over the same period. Constituents analyzed were aluminum (Al), antimony (Sb), arsenic (As), barium (Ba), beryllium (Be), boron (B), cadmium (Cd), chromium (Cr), cobalt (Co), copper (Cu), iron (Fe), lead (Pb), lithium (Li), manganese (Mn), mercury (Hg), molybdenum

Preliminary Experimental Analysis of Soil Stabilizers for Contamination Control

International Nuclear Information System (INIS)

Lagos, L.; Varona, J.; Zidan, A.; Gudavalli, R.; Wu, Kuang-His

2006-01-01

A major focus of Department of Energy's (DOE's) environmental management mission at the Hanford site involves characterizing and remediating contaminated soil and groundwater; stabilizing contaminated soil; remediating disposal sites; decontaminating and decommissioning structures, and demolishing former plutonium production process buildings, nuclear reactors, and separation plants; maintaining inactive waste sites; transitioning facilities into the surveillance and maintenance program; and mitigating effects to biological and cultural resources from site development and environmental cleanup and restoration activities. For example, a total of 470,914 metric tons of contaminated soil from 100 Areas remediation activities were disposed at the Environmental Restoration Disposal Facility (ERDF) during 2004. The Applied Research Center (ARC) at Florida International University (FIU) is supporting the Hanford's site remediation program by analyzing the effectiveness of several soil stabilizers (fixatives) for contamination control during excavation activities. The study is focusing on determining the effects of varying soil conditions, temperature, humidity and wind velocity on the effectiveness of the candidate stabilizers. The test matrix consists of a soil penetration-depth study, wind tunnel experiments for determination of threshold velocity, and temperature and moisture-controlled drying/curing experiments. These three set of experiments are designed to verify performance metrics, as well as provide insight into what fundamental forces are altered by the use of the stabilizer. This paper only presents the preliminary results obtained during wind tunnel experiments using dry Hanford soil samples (with 2.7% moisture by weight). These dry soil samples were exposed to varying wind speeds from 2.22 m/sec to 8.88 m/sec. Furthermore, airborne particulate data was collected for the dry Hanford soil experiments using an aerosol analyzer instrument. (authors)

Trace element profiles of the sea anemone Anemonia viridis living nearby a natural CO2 vent

Directory of Open Access Journals (Sweden)

Rael Horwitz

2014-09-01

Full Text Available Ocean acidification (OA is not an isolated threat, but acts in concert with other impacts on ecosystems and species. Coastal marine invertebrates will have to face the synergistic interactions of OA with other global and local stressors. One local factor, common in coastal environments, is trace element contamination. CO2 vent sites are extensively studied in the context of OA and are often considered analogous to the oceans in the next few decades. The CO2 vent found at Levante Bay (Vulcano, NE Sicily, Italy also releases high concentrations of trace elements to its surrounding seawater, and is therefore a unique site to examine the effects of long-term exposure of nearby organisms to high pCO2 and trace element enrichment in situ. The sea anemone Anemonia viridis is prevalent next to the Vulcano vent and does not show signs of trace element poisoning/stress. The aim of our study was to compare A. viridis trace element profiles and compartmentalization between high pCO2 and control environments. Rather than examining whole anemone tissue, we analyzed two different body compartments—the pedal disc and the tentacles, and also examined the distribution of trace elements in the tentacles between the animal and the symbiotic algae. We found dramatic changes in trace element tissue concentrations between the high pCO2/high trace element and control sites, with strong accumulation of iron, lead, copper and cobalt, but decreased concentrations of cadmium, zinc and arsenic proximate to the vent. The pedal disc contained substantially more trace elements than the anemone’s tentacles, suggesting the pedal disc may serve as a detoxification/storage site for excess trace elements. Within the tentacles, the various trace elements displayed different partitioning patterns between animal tissue and algal symbionts. At both sites iron was found primarily in the algae, whereas cadmium, zinc and arsenic were primarily found in the animal tissue. Our data

Trace element profiles of the sea anemone Anemonia viridis living nearby a natural CO2 vent.

Science.gov (United States)

Horwitz, Rael; Borell, Esther M; Fine, Maoz; Shaked, Yeala

2014-01-01

Ocean acidification (OA) is not an isolated threat, but acts in concert with other impacts on ecosystems and species. Coastal marine invertebrates will have to face the synergistic interactions of OA with other global and local stressors. One local factor, common in coastal environments, is trace element contamination. CO2 vent sites are extensively studied in the context of OA and are often considered analogous to the oceans in the next few decades. The CO2 vent found at Levante Bay (Vulcano, NE Sicily, Italy) also releases high concentrations of trace elements to its surrounding seawater, and is therefore a unique site to examine the effects of long-term exposure of nearby organisms to high pCO2 and trace element enrichment in situ. The sea anemone Anemonia viridis is prevalent next to the Vulcano vent and does not show signs of trace element poisoning/stress. The aim of our study was to compare A. viridis trace element profiles and compartmentalization between high pCO2 and control environments. Rather than examining whole anemone tissue, we analyzed two different body compartments-the pedal disc and the tentacles, and also examined the distribution of trace elements in the tentacles between the animal and the symbiotic algae. We found dramatic changes in trace element tissue concentrations between the high pCO2/high trace element and control sites, with strong accumulation of iron, lead, copper and cobalt, but decreased concentrations of cadmium, zinc and arsenic proximate to the vent. The pedal disc contained substantially more trace elements than the anemone's tentacles, suggesting the pedal disc may serve as a detoxification/storage site for excess trace elements. Within the tentacles, the various trace elements displayed different partitioning patterns between animal tissue and algal symbionts. At both sites iron was found primarily in the algae, whereas cadmium, zinc and arsenic were primarily found in the animal tissue. Our data suggests that A. viridis

Chemical and biological factors affecting bioavailability of contaminants in seawater

International Nuclear Information System (INIS)

Knezovich, J.P.

1992-09-01

This paper discusses the influence that salinity has on the bioavailability of the two largest classes of contaminants, trace metals and organic compounds will be discussed. Although data on contaminant toxicity will be used to draw inferences about chemical availability, this discussion will focus on the properties that contaminants are likely to exhibit in waters of varying salinities. In addition, information on physiological changes that are affected by salinity will be used to illustrate how biological effects can alter the apparent availability of contaminants

Trace analysis for 300 MM wafers and processes with TXRF

International Nuclear Information System (INIS)

Nutsch, A.; Erdmann, V.; Zielonka, G.; Pfitzner, L.; Ryssel, H.

2000-01-01

Efficient fabrication of semiconductor devices is combined with an increasing size of silicon wafers. The contamination level of processes, media, and equipment has to decrease continuously. A new test laboratory for 300 mm was installed in view of the above mentioned aspects. Aside of numerous processing tools this platform consist electrical test methods, particle detection, vapor phase decomposition (VPD) preparation, and TXRF. The equipment is installed in a cleanroom. It is common to perform process or equipment control, development, evaluation and qualification with monitor wafers. The evaluation and the qualification of 300 mm equipment require direct TXRF on 300 mm wafers. A new TXRF setup was installed due to the wafer size of 300 mm. The 300 mm TXRF is equipped with tungsten and molybdenum anode. This combination allows a sensitive detection of elements with fluorescence energy below 10 keV for tungsten excitation. The molybdenum excitation enables the detection of a wide variety of elements. The detection sensitivity for the tungsten anode excited samples is ten times higher than for molybdenum anode measured samples. The system is calibrated with 1 ng Ni. This calibration shows a stability within 5 % when monitored to control system stability. Decreasing the amount of Ni linear results in a linear decrease of the measured Ni signal. This result is verified for a range of elements by multielement samples. New designs demand new processes and materials, e.g. ferroelectric layers and copper. The trace analysis of many of these materials is supported by the higher excitation energy of the molybdenum anode. Reclaim and recycling of 300 mm wafers demand for an accurate contamination control of the processes to avoid cross contamination. Polishing or etching result in modified surfaces. TXRF as a non-destructive test method allows the simultaneously detection of a variety of elements on differing surfaces in view of contamination control and process

Impact of inorganic contaminants on microalgae productivity and bioremediation potential.

Science.gov (United States)

Torres, Eric M; Hess, Derek; McNeil, Brian T; Guy, Tessa; Quinn, Jason C

2017-05-01

As underdeveloped nations continue to industrialize and world population continues to increase, the need for energy, natural resources, and goods will lead to ever increasing inorganic contaminants, such as heavy metals, in various waste streams that can have damaging effects on plant life, wildlife, and human health. This work is focused on the evaluation of the potential of Nannochloropsis salina to be integrated with contaminated water sources for the concurrent production of a biofuel feedstock while providing an environmental service through bioremediation. Individual contaminants (As, Cd, Cr, Co, Cu, Pb, Ni, Hg, Se, and Zn) at various concentrations ranging from a low concentration (1X) to higher concentrations (10X, and 40X) found in contaminated systems (mine tailings, wastewater treatment plants, produced water) were introduced into growth media. Biological growth experimentation was performed in triplicate at the various contaminant concentrations and at 3 different light intensities. Results show that baseline concentrations of each contaminant slightly decreased biomass growth to between 89% and 99% of the control with the exception of Ni which dramatically reduced growth. Increased contaminant concentrations resulted in progressively lower growth rates for all contaminants tested. Lipid analysis shows most baseline contaminant concentrations slightly decrease or have minimal effects on lipid content at all light levels. Trace contaminant analysis on the biomass showed Cd, Co, Cu, Pb, and Zn were sorbed by the microalgae with minimal contaminants remaining in the growth media illustrating the effectiveness of microalgae to bioremediate these contaminants when levels are sufficiently low to not detrimentally impact productivity. The microalgae biomass was less efficient at sorption of As, Cr, Ni, and Se. Copyright © 2017 Elsevier Inc. All rights reserved.

Improving the control of aflatoxin-contaminated foods in Haiti | IDRC ...

International Development Research Centre (IDRC) Digital Library (Canada)

They are regularly found among staple food commodities such as peanuts, ... Factors influencing the adoption of control methods by farmers, harvesters, ... viable non-food/feed-related value chain for rejected aflatoxin-contaminated peanuts.

Risk assessment of trace metal-polluted coastal sediments on Hainan Island: A full-scale set of 474 geographical locations covering the entire island.

Science.gov (United States)

Li, Feng; Lin, Ze-Feng; Wen, Jia-Sheng; Wei, Yan-Sha; Gan, Hua-Yang; He, Hai-Jun; Lin, Jin-Qin; Xia, Zhen; Chen, Bi-Shuang; Guo, Wen-Jie; Tan, Cha-Sheng; Cai, Hua-Yang

2017-12-15

Hainan Island is the second largest island and one of the most famous tourist destinations in China, but sediment contamination by trace metals in coastal areas is a major issue. However, full-scale risk assessments of trace metal-polluted coastal sediments are lacking. In this study, coastal surface sediments from 474 geographical locations covering almost the entire island were collected to identify risk-related variables. Controlling factors and possible sources of trace metals were identified, and the toxicity effects were carefully evaluated. Our results suggest that trace-metal pollution in coastal sediments, which was mainly caused by Pb, Zn and Cu emissions, has primarily resulted from industrial sewage and shipping activities and has threatened the offshore ecosystem of Hainan Island and warrants extensive consideration. This is the first study that has systematically investigated trace metal-polluted coastal sediments throughout the entirety of Hainan Island and provides solid evidence for sustainable marine management in the region. Copyright © 2017 Elsevier Ltd. All rights reserved.

Control System Radioactive Contamination in Food Samples in Poland

International Nuclear Information System (INIS)

Grabowski, D.; Kurowski, W.; Muszynski, W.; Rubel, B.; Smagala, G.; Swietochowska, J.

2001-01-01

Full text: The analyses of the level of radioactive contamination in food samples are carried out by the Service for Measurements of Radioactive Contamination (SMRC) in Poland. The Service was brought into existence in 1961. The Service comprises of a network of measurement stations and the Centre of Radioactive Contamination Measurements (CRCM). The duty of the Centre is being executed by the Central Laboratory for Radiological Protection (CLRP). The uniform methods of sampling are used in measurement stations. All important foodstuff: milk, meat, vegetables, fruit, cereals are controlled in the Service stations. The radiochemical and spectrometric methods are used to determine the activity of radioactive isotopes. The standard equipment of the measurement station is the measurement system type SAPOS-90 and multichannel analyser with scintillation or germanium detector. The structure of the Service, kinds of samples tested by each station, program of sampling in normal and during accident situation are presented in this paper. (author)

Trace metals in fugitive dust from unsurfaced roads in the Viburnum Trend resource mining District of Missouri--implementation of a direct-suspension sampling methodology.

Science.gov (United States)

Witt, Emitt C; Wronkiewicz, David J; Pavlowsky, Robert T; Shi, Honglan

2013-09-01

Fugitive dust from 18 unsurfaced roadways in Missouri were sampled using a novel cyclonic fugitive dust collector that was designed to obtain suspended bulk samples for analysis. The samples were analyzed for trace metals, Fe and Al, particle sizes, and mineralogy to characterize the similarities and differences between roadways. Thirteen roads were located in the Viburnum Trend (VT) mining district, where there has been a history of contaminant metal loading of local soils; while the remaining five roads were located southwest of the VT district in a similar rural setting, but without any mining or industrial process that might contribute to trace metal enrichment. Comparison of these two groups shows that trace metal concentration is higher for dusts collected in the VT district. Lead is the dominant trace metal found in VT district dusts representing on average 79% of the total trace metal concentration, and was found moderately to strongly enriched relative to unsurfaced roads in the non-VT area. Fugitive road dust concentrations calculated for the VT area substantially exceed the 2008 Federal ambient air standard of 0.15μgm(-3) for Pb. The pattern of trace metal contamination in fugitive dust from VT district roads is similar to trace metal concentrations patterns observed for soils measured more than 40years ago indicating that Pb contamination in the region is persistent as a long-term soil contaminant. Published by Elsevier Ltd.

Of the necessity of knowledge of the natural pedo-geochemical background content in the evaluation of the contamination of soils by trace elements.

Science.gov (United States)

Baize, D; Sterckeman, T

2001-01-08

In order to evaluate the contamination of the Dornach (Switzerland) site within the framework of the CEEM-Soil project, each participating team was allowed to take a maximum of 15 samples. The French team's sampling was organized in such a way as to answer the following questions: (i) what is the natural concentration of the soils at this site (local pedo-geochemical background content)?; (ii) what are the levels of Cd, Cu, Pb and Zn contamination of the soil?; (iii) what is the depth reached by the surface contamination that is derived from atmospheric fallout?; (iv) how is the contamination spread along the longest axis of the area under study? The relationships between total Fe and the trace metals have allowed local variations in the natural pedo-geochemical background content to be detected and thus permitted the anthropogenic contamination to be estimated. There would appear to be a low level of Pb contamination over all the site investigated (an increase of the order of 5-10 mg kg(-1) on the background level), limited to the surface humus-bearing layers. There is also a significant contamination by Cu over all of the site (an increase of the order of 30-40 mg kg(-1)). This contamination has remained in the surface horizons (0-20 cm). Very high Zn and Cd concentrations have been found in the four surface (0-4 cm) and deep horizons (15-70 cm) taken under the forest and very much lower values in the samples taken from cultivated soils. The most likely explanation is an unequal inheritance between the upper part of the site (wooded with thinner very clayey soils) and the lower cultivated part of the site (with thicker less clayey soils developed in a loamy material). For various reasons, it seems unlikely that a contamination of the wooded part should be so much higher than the cultivated part due to the interception of atmospheric dust by the trees. The local pedo-geochemical background Cd and Zn content of the upper wooded part proved to be clearly higher than

Trace elements and naturally occurring radioactive materials in 'Non-traditional fertilizers' used in Ghana

International Nuclear Information System (INIS)

Assibey, E. O.

2013-07-01

Fertilizers have been implicated for being contaminated with toxic trace elements and naturally occurring radioactive materials (NORMs) even though they are an indispensable component of our agriculture. This phenomenon of contamination has been investigated and established world-wide in various forms of fertilizers (i.e., granular or 'traditional' type and liquid/powder or 'non-traditional type'). In Ghana, the crop sub-sector has seen a gradual rise in the importation and use of 'non-traditional fertilizers' which are applied to both the foliar parts and roots of plants. This notwithstanding, research on fertilizers has been largely skewed towards the 'traditional' types, focusing principally on the subjects of yield, effects of application and their quality. This study was, therefore, undertaken to bridge the knowledge gap by investigating the levels of trace elements and NORMs found in the 'non-traditional' fertilizers used in Ghana. The principal objective of the study was to investigate the suitability of the 'non-traditional fertilizers' for agricultural purposes with respect to trace elements and NORMs contamination. Atomic Absorption Spectrometry and instrumental Neutron Activation Analysis were employed to determine the trace elements (Cu, Zn, Fe, Na, Al, Br, Ni, Cd, As, Hg, Co, Pb, La, Mn, Si, Ca, Cl, S, K, Ba and V) and NORMs ( 238 U, 232 Th and 40 K) concentrations in thirty-nine (39) fertilizer samples taken from two major agro-input hubs in the country (Kumasi-Kejetia and Accra). Multivariate statistical analyses (cluster analysis, principal component analysis and pearson's correlation) were applied to the data obtained in order to identify possible sources of contamination, investigate sample/ parameter affinities and groupings and for fingerprinting. The toxic trace element concentrations determined in all samples were found to be in the order Fe>Cu>Co>Cd>Cr >Ni>Pb>As>Hg. The study found most of the trace elements determined to be within limits set

Avoidance of polycyclic aromatic hydrocarbon-contaminated sediments by the freshwater invertebrates Gammarus pulex and Asellus aquaticus

NARCIS (Netherlands)

Lange, de H.J.; Sperber, V.; Peeters, E.T.H.M.

2006-01-01

Contamination of sediments is a serious problem in most industrialized areas. Sediments are often contaminated with trace metals and organic contaminants like polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). Bioassays are often used to determine the effect of

Inorganic and organic trace mineral supplementation in weanling pig diets

Directory of Open Access Journals (Sweden)

MARIA C. THOMAZ

2015-06-01

Full Text Available A study was conducted to evaluate the effects of dietary inorganic and organic trace minerals in two levels of supplementation regarding performance, diarrhea occurrence, hematological parameters, fecal mineral excretion and mineral retention in metacarpals and liver of weanling pigs. Seventy piglets weaned at 21 days of age with an average initial body weight of 6.70 ± 0.38 kg were allotted in five treatments: control diet (no added trace mineral premix; 50% ITMP (control diet with inorganic trace mineral premix supplying only 50% of trace mineral requirements; 50% OTMP (control diet with organic trace mineral premix supplying only 50% of trace mineral requirements; 100% ITMP (control diet with inorganic trace mineral premix supplying 100% of trace mineral requirements; and 100% OTMP (control diet with organic trace mineral premix supplying 100% of trace mineral requirements. Feed intake and daily weight gain were not affected by treatments, however, piglets supplemented by trace minerals presented better gain:feed ratio. No differences were observed at calcium, phosphorus, potassium, magnesium, sodium and sulfur excreted in feces per kilogram of feed intake. Treatments did not affect calcium, phosphorus, magnesium, sulfur and iron content in metacarpals. Trace mineral supplementation, regardless of level and source, improved the performance of piglets.

Water contamination with heavy metals and trace elements from Kilembe copper mine and tailing sites in Western Uganda; implications for domestic water quality.

Science.gov (United States)

Abraham, Mwesigye R; Susan, Tumwebaze B

2017-02-01

The mining and processing of copper in Kilembe, Western Uganda, from 1956 to 1982 left over 15 Mt of cupriferous and cobaltiferous pyrite dumped within a mountain river valley, in addition to mine water which is pumped to the land surface. This study was conducted to assess the sources and concentrations of heavy metals and trace elements in Kilembe mine catchment water. Multi-element analysis of trace elements from point sources and sinks was conducted which included mine tailings, mine water, mine leachate, Nyamwamba River water, public water sources and domestic water samples using ICP-MS. The study found that mean concentrations (mg kg -1 ) of Co (112), Cu (3320), Ni (131), As (8.6) in mine tailings were significantly higher than world average crust and were being eroded and discharged into water bodies within the catchment. Underground mine water and leachate contained higher mean concentrations (μg L -1 ) of Cu (9470), Co (3430) and Ni (590) compared with background concentrations (μg L -1 ) in un contaminated water of 1.9, 0.21 and 0.67 for Cu, Co and Ni respectively. Over 25% of household water samples exceeded UK drinking water thresholds for Al of 200 μg L -1 , Co exceeded Winsconsin (USA drinking) water thresholds of 40 μg L -1 in 40% of samples while Fe in 42% of samples exceeded UK thresholds of 200 μg L -1 . The study however found that besides mining activities, natural processes of geological weathering also contributed to Al, Fe, and Mn water contamination in a number of public water sources. Copyright © 2016 Elsevier Ltd. All rights reserved.

Food product tracing technology capabilities and interoperability.

Science.gov (United States)

Bhatt, Tejas; Zhang, Jianrong Janet

2013-12-01

Despite the best efforts of food safety and food defense professionals, contaminated food continues to enter the food supply. It is imperative that contaminated food be removed from the supply chain as quickly as possible to protect public health and stabilize markets. To solve this problem, scores of technology companies purport to have the most effective, economical product tracing system. This study sought to compare and contrast the effectiveness of these systems at analyzing product tracing information to identify the contaminated ingredient and likely source, as well as distribution of the product. It also determined if these systems can work together to better secure the food supply (their interoperability). Institute of Food Technologists (IFT) hypothesized that when technology providers are given a full set of supply-chain data, even for a multi-ingredient product, their systems will generally be able to trace a contaminated product forward and backward through the supply chain. However, when provided with only a portion of supply-chain data, even for a product with a straightforward supply chain, it was expected that interoperability of the systems will be lacking and that there will be difficulty collaborating to identify sources and/or recipients of potentially contaminated product. IFT provided supply-chain data for one complex product to 9 product tracing technology providers, and then compared and contrasted their effectiveness at analyzing product tracing information to identify the contaminated ingredient and likely source, as well as distribution of the product. A vertically integrated foodservice restaurant agreed to work with IFT to secure data from its supply chain for both a multi-ingredient and a simpler product. Potential multi-ingredient products considered included canned tuna, supreme pizza, and beef tacos. IFT ensured that all supply-chain data collected did not include any proprietary information or information that would otherwise

Trace element measurement for assessment of dog food safety

NARCIS (Netherlands)

Bode, P.; De Nadai Fernandes, E.A.; Elias, Camila; Bacchi, Marcio

2017-01-01

The quality of dog diets depends on adequate ingredients capable of providing optimal nutrition and free of contaminants, for promoting long-term health. Trace elements in 95 samples of dry food for dog puppies (n = 32) and adults (n = 63) of various brands were measured using instrumental neutron

Variations in time and space of trace metal aerosol concentrations in urban areas and their surroundings

Science.gov (United States)

Moreno, T.; Querol, X.; Alastuey, A.; Reche, C.; Cusack, M.; Amato, F.; Pandolfi, M.; Pey, J.; Richard, A.; Prévôt, A. S. H.; Furger, M.; Gibbons, W.

2011-09-01

Using an unprecedentedly large geochemical database, we compare temporal and spatial variations in inhalable trace metal background concentrations in a major city (Barcelona, Spain) and at a nearby mountainous site (Montseny) affected by the urban plume. Both sites are contaminated by technogenic metals, with V, Pb, Cu, Zn, Mn, Sn, Bi, Sb and Cd all showing upper continental crust (UCC) normalised values >1 in broadly increasing order. The highest metal concentrations usually occur during winter at Barcelona and summer in Montseny. This seasonal difference was especially marked at the remote mountain site in several elements such as Ti and Rare Earth Elements, which recorded campaign maxima, exceeding PM10 concentrations seen in Barcelona. The most common metals were Zn, Ti, Cu, Mn, Pb and V. Both V and Ni show highest concentrations in summer, and preferentially fractionate into the finest PM sizes (PM1/PM10 > 0.5) especially in Barcelona, this being attributed to regionally dispersed contamination from fuel oil combustion point sources. Within the city, hourly metal concentrations are controlled either by traffic (rush hour double peak for Cu, Sb, Sn, Ba) or industrial plumes (morning peak of Ni, Mn, Cr generated outside the city overnight), whereas at Montseny metal concentrations rise during the morning to a single, prolonged afternoon peak as contaminated air transported by the sea breeze moves into the mountains. Our exceptional database, which includes hourly measurements of chemical concentrations, demonstrates in more detail than previous studies the spatial and temporal variability of urban pollution by trace metals in a given city. Technogenic metalliferous aerosols are commonly fine in size and therefore potentially bioavailable, emphasising the case for basing urban background PM characterisation not only on physical parameters such as mass but also on sample chemistry and with special emphasis on trace metal content.

Contaminated nickel scrap processing

International Nuclear Information System (INIS)

Compere, A.L.; Griffith, W.L.; Hayden, H.W.; Johnson, J.S. Jr.; Wilson, D.F.

1994-12-01

The DOE will soon choose between treating contaminated nickel scrap as a legacy waste and developing high-volume nickel decontamination processes. In addition to reducing the volume of legacy wastes, a decontamination process could make 200,000 tons of this strategic metal available for domestic use. Contaminants in DOE nickel scrap include 234 Th, 234 Pa, 137 Cs, 239 Pu (trace), 60 Co, U, 99 Tc, and 237 Np (trace). This report reviews several industrial-scale processes -- electrorefining, electrowinning, vapormetallurgy, and leaching -- used for the purification of nickel. Conventional nickel electrolysis processes are particularly attractive because they use side-stream purification of process solutions to improve the purity of nickel metal. Additionally, nickel purification by electrolysis is effective in a variety of electrolyte systems, including sulfate, chloride, and nitrate. Conventional electrorefining processes typically use a mixed electrolyte which includes sulfate, chloride, and borate. The use of an electrorefining or electrowinning system for scrap nickel recovery could be combined effectively with a variety of processes, including cementation, solvent extraction, ion exchange, complex-formation, and surface sorption, developed for uranium and transuranic purification. Selected processes were reviewed and evaluated for use in nickel side-stream purification. 80 refs

49 Trace Metals' Contamination of Stream Water and Irrigated Crop ...

African Journals Online (AJOL)

ABUBAKAR AHMED

human consumption as they pose serious health risks due to contamination with the metals. For environmental ... mining activities, industrial and domestic effluents, urban ... drinking and bathing water, irrigation, food, fuel and energy.

Trace metals in water and sediments from Ologe Lagoon, southwestern Nigeria

International Nuclear Information System (INIS)

Yusuf, K.A.; Osibanjo, O.

2006-01-01

The concentrations of trace metals in water and sediment samples from Ologe lagoon located in southwestern Nigeria were investigated. The lagoon is a source of water for domestic, transportation and fishing activities. The water quality characteristics for a period of two years (January, 1997 - November, 1998), and the speciation of metals in the lagoon sediments were evaluated. The lagoon water quality characteristics, with respect to heavy metal contamination, were compared with global averages for freshwater and international water quality standards for drinking water. All elements except iron, were well within the safety limits. Sequential extraction techniques were used to establish the association of the total concentrations of Zn, Cu, Pb, Cd and Mn in the sediment samples with their contents as exchangeable, carbonates, Fe/Mn oxides, and organic and residual fractions. The concentrations of trace metals in the whole sediments were generally below the world-wide background levels. When compared to a number of sediment quality guidelines, the concentrations of trace metals were found to be below the level considered to have the potential to cause biological effects. Pb and Cd were extracted from the residual fraction at values greater than 50%. The metals that were most easily extractable in the samples analyzed were Mn and Zn, which posed the highest risk to water contamination. The low level of industrialization in the study area has kept the lagoon relatively free from heavy metal contamination. (author)

Evaluation of Soil Contamination Indices in a Mining Area of Jiangxi, China

Science.gov (United States)

Wu, Jin; Teng, Yanguo; Lu, Sijin; Wang, Yeyao; Jiao, Xudong

2014-01-01

There is currently a wide variety of methods used to evaluate soil contamination. We present a discussion of the advantages and limitations of different soil contamination assessment methods. In this study, we analyzed seven trace elements (As, Cd, Cr, Cu, Hg, Pb, and Zn) that are indicators of soil contamination in Dexing, a city in China that is famous for its vast nonferrous mineral resources in China, using enrichment factor (EF), geoaccumulation index (Igeo), pollution index (PI), and principal component analysis (PCA). The three contamination indices and PCA were then mapped to understand the status and trends of soil contamination in this region. The entire study area is strongly enriched in Cd, Cu, Pb, and Zn, especially in areas near mine sites. As and Hg were also present in high concentrations in urban areas. Results indicated that Cr in this area originated from both anthropogenic and natural sources. PCA combined with Geographic Information System (GIS) was successfully used to discriminate between natural and anthropogenic trace metals. PMID:25397401

Open-water and under-ice seasonal variations in trace element content and physicochemical associations in fluvial bed sediment.

Science.gov (United States)

Doig, Lorne E; Carr, Meghan K; Meissner, Anna G N; Jardine, Tim D; Jones, Paul D; Bharadwaj, Lalita; Lindenschmidt, Karl-Erich

2017-11-01

Across the circumpolar world, intensive anthropogenic activities in the southern reaches of many large, northward-flowing rivers can cause sediment contamination in the downstream depositional environment. The influence of ice cover on concentrations of inorganic contaminants in bed sediment (i.e., sediment quality) is unknown in these rivers, where winter is the dominant season. A geomorphic response unit approach was used to select hydraulically diverse sampling sites across a northern test-case system, the Slave River and delta (Northwest Territories, Canada). Surface sediment samples (top 1 cm) were collected from 6 predefined geomorphic response units (12 sites) to assess the relationships between bed sediment physicochemistry (particle size distribution and total organic carbon content) and trace element content (mercury and 18 other trace elements) during open-water conditions. A subset of sites was resampled under-ice to assess the influence of season on these relationships and on total trace element content. Concentrations of the majority of trace elements were strongly correlated with percent fines and proxies for grain size (aluminum and iron), with similar trace element grain size/grain size proxy relationships between seasons. However, finer materials were deposited under ice with associated increases in sediment total organic carbon content and the concentrations of most trace elements investigated. The geomorphic response unit approach was effective at identifying diverse hydrological environments for sampling prior to field operations. Our data demonstrate the need for under-ice sampling to confirm year-round consistency in trace element-geochemical relationships in fluvial systems and to define the upper extremes of these relationships. Whether contaminated or not, under-ice bed sediment can represent a "worst-case" scenario in terms of trace element concentrations and exposure for sediment-associated organisms in northern fluvial systems

Possibility of using radioactivity control measurements for determining contamination paths in nutritional vectors

International Nuclear Information System (INIS)

Garnier, A.

1966-01-01

The object of the report is to study the possibility of using results of radioactivity controls for determining the paths followed by contamination in nutritional vectors; these are necessary for calculating protection norms. Radioactive contamination of a nutritional vector is expressed in terms of parameters which suggest that a certain number of criteria may be used for choosing the results which are to be exploited. An actual example of a 'vertical' study based on results of measurements made purely for control purposes shows the difficulties which may be encountered. A list of the results obtained by the control networks set up in the Community Countries, either for the atmosphere, for milk, or for other foodstuffs, shows that these networks are not at the present organised in such a way as to make such a study possible. It appears desirable that a large part of the work carried out by the control Services be oriented in such a way as to yield the complementary information required for experimental studies of radioactive contamination transfers. (author) [fr

Contamination of dried blood spots - an underestimated risk in newborn screening.

Science.gov (United States)

Winter, Theresa; Lange, Anja; Hannemann, Anke; Nauck, Matthias; Müller, Cornelia

2018-01-26

Newborn screening (NBS) is an established screening procedure in many countries worldwide, aiming at the early detection of inborn errors of metabolism. For decades, dried blood spots have been the standard specimen for NBS. The procedure of blood collection is well described and standardized and includes many critical pre-analytical steps. We examined the impact of contamination of some anticipated common substances on NBS results obtained from dry spot samples. This possible pre-analytical source of uncertainty has been poorly examined in the past. Capillary blood was obtained from 15 adult volunteers and applied to 10 screening filter papers per volunteer. Nine filter papers were contaminated without visible trace. The contaminants were baby diaper rash cream, baby wet wipes, disinfectant, liquid infant formula, liquid infant formula hypoallergenic (HA), ultrasonic gel, breast milk, feces, and urine. The differences between control and contaminated samples were evaluated for 45 NBS quantities. We estimated if the contaminations might lead to false-positive NBS results. Eight of nine investigated contaminants significantly altered NBS analyte concentrations and potentially caused false-positive screening outcomes. A contamination with feces was most influential, affecting 24 of 45 tested analytes followed by liquid infant formula (HA) and urine, affecting 19 and 13 of 45 analytes, respectively. A contamination of filter paper samples can have a substantial effect on the NBS results. Our results underline the importance of good pre-analytical training to make the staff aware of the threat and ensure reliable screening results.

Spatial variations in trace element concentrations of the sea urchin, Paracentrotus lividus, a first reference study in the Mediterranean Sea.

Science.gov (United States)

Ternengo, S; Marengo, M; El Idrissi, O; Yepka, J; Pasqualini, V; Gobert, S

2018-04-01

A study on Trace Elements (TE) from sea urchin gonads has been conducted in the western Mediterranean Sea. Contamination data were used to determine a Trace Method Pollution Index (TEPI). TE concentrations varied considerably depending on the location of the sampling stations. The results showed that five trace elements (Zn, Fe, As, Al, Cu) are ubiquitous. The geographical area considered (Corsica) represents an important range of environmental conditions and types of pressure that can be found in the western Mediterranean Sea. TEPI was used to classify the studied sites according to their degree of contamination and allowed reliable comparison of TE contamination between local and international sites. TE contamination of the western Mediterranean Sea displayed a north-to-south gradient, from the Italian coasts down through the insular Corsican coasts to the north African littoral. Due to the increasing environmental pressure on the Mediterranean Sea, a regular monitoring of TE levels in marine organisms is necessary to prevent any further environmental deterioration. Copyright © 2018 Elsevier Ltd. All rights reserved.

A PERMEABLE ACTIVE AMENDMENT CONCRETE (PAAC) FOR CONTAMINANT REMEDIATION AND EROSION CONTROL

Energy Technology Data Exchange (ETDEWEB)

Knox, A.; Paller, M.; Dixon, K.

2012-06-29

The final project report for SEED SERDP ER - 2134 describes the development of permeable active amendment concrete (PAAC), which was evaluated through four tasks: 1) development of PAAC; 2) assessment of PAAC for contaminant removal; 3) evaluation of promising PAAC formulations for potential environmental impacts; and 4) assessment of the hydraulic, physical, and structural properties of PAAC. Conventional permeable concrete (often referred to as pervious concrete) is concrete with high porosity as a result of an extensive and interconnected void content. It is made from carefully controlled amounts of water and cementitious materials used to create a paste that forms a coating around aggregate particles. The mixture has a substantial void content (e.g., 15% - 25%) that results in a highly permeable structure that drains quickly. In PAAC, the aggregate material is partly replaced by chemically-active amendments that precipitate or adsorb contaminants in water that flows through the concrete interstices. PAAC combines the relatively high structural strength, ample void space, and water permeability of pervious concrete with the contaminant sequestration ability of chemically-active amendments to produce a new material with superior durability and ability to control contaminant mobility. The high surface area provided by the concrete interstices in PAAC provides significant opportunity for contaminants to react with the amendments incorporated into the concrete matrix. PAAC has the potential to immobilize a large variety of organic and inorganic contaminants by incorporating different active sequestering agents including phosphate materials (rock phosphate), organoclays, zeolite, and lime individually or in combinations.

Soil Contamination in Fadama Area in Zaria, Nigeria, Using X-ray ...

African Journals Online (AJOL)

Journal of the Nigerian Association of Mathematical Physics ... In this study, the soil contamination level of all heavy metals and trace elements was compared to the range, mean, and median values of the World soil as well as with ... However, contamination level of all elements was not evenly distributed in the studied area.

Integrating Modeling and Monitoring to Provide Long-Term Control of Contaminants

International Nuclear Information System (INIS)

Fogwell, Th.

2009-01-01

An introduction is presented of the types of problems that exist for long-term control of radionuclides at DOE sites. A breakdown of the distributions at specific sites is given, together with the associated difficulties. A paradigm for remediation showing the integration of monitoring with modeling is presented. It is based on a feedback system that allows for the monitoring to act as principal sensors in a control system. Currently the establishment of a very prescriptive monitoring program fails to have a mechanism for improving models and improving control of the contaminants. The resulting system can be optimized to improve performance. Optimizing monitoring automatically entails linking the monitoring with modeling. If monitoring designs were required to be more efficient, thus requiring optimization, then the monitoring automatically becomes linked to modeling. Records of decision could be written to accommodate revisions in monitoring as better modeling evolves. The technical pieces of the required paradigm are already available; they just need to be implemented and applied to solve the long-term control of the contaminants. An integration of the various parts of the system is presented. Each part is described, and examples are given. References are given to other projects which bring together similar elements in systems for the control of contaminants. Trends are given for the development of the technical features of a robust system. Examples of monitoring methods for specific sites are given. The examples are used to illustrate how such a system would work. Examples of technology needs are presented. Finally, other examples of integrated modeling-monitoring approaches are presented. (authors)

Stationary point of the radiometric control of cesium contamination of agricultural animals

International Nuclear Information System (INIS)

1997-01-01

Stationary point of the radiometric control of cesium contamination of an agricultural animals. Is intended for vital measurements of the contents of radiocesium in muscular tissue of a cattle. Can be used on cattle-breeding farms, providing points, in meat factories and personal facilities. As a base means for accommodation of the control point the motor-car is used. Design of the car allows to automate operations on deployment of the control point on a place and translation of one to a transport mode. Limits of measured specific activity of cesium contamination of a cattle is up 5*10 -9 to 5*10 -6 Ci/kg. The basic error on the bottom limit of measurement at confidence coefficient 0,95 is no more than 30%. Measurement time for the bottom limit of determined specific activity is no more than 30 s. There is automatic measurement mode. Type of a power is 220 V, 50 Hz. Range of working temperatures is up -15 to +35 centigrade. Relative humidity is no more than 98% at 25 centigrade. External gamma background is till 0.035 mR/h. Time of installation and dismantle of stationary control point is no more than 1,5 hours. The direct radiometric control in divo allows to fulfil and to use biotechnological process of removing of cesium isotopes from body of animals for decrease of levels of radioactive contamination

Results of EPR dosimetry for population in the vicinity of the most contaminating radioactive fallout trace after the first nuclear test in the Semipalatinsk test site

International Nuclear Information System (INIS)

Ivannikov, Alexander; Zhumadilov, Kassym; Tieliewuhan, Eldana

2006-01-01

The method of electron paramagnetic resonance (EPR) spectroscopy for tooth enamel is applied to individual radiation dose determination to residents of two villages (Dolon and Mostik) in the vicinity of the Semipalatinsk nuclear test site in Kazakhstan. These villages are located near the central axis of the radioactive fallout trace of the most contaminating surface nuclear test conducted in 1949. It is found that excess doses obtained by subtraction of natural background dose from dose absorbed in enamel range up to 440 mGy to residents of Dolon, whose enamel was formed before 1949, and do not exceed 120 mGy to younger residents. To residents of Mostik, excess doses do not exceed 100 mGy regardless of age except for one resident with an extremely high dose of 1.25 Gy. These results are in agreement with the pattern of radioactive contamination of the territory after the nuclear test of 1949 except one case of extremely high dose, which should be additionally investigated. (author)

Updated study reporting levels (SRLs) for trace-element data collected for the California Groundwater Ambient Monitoring and Assessment (GAMA) Priority Basin Project, October 2009-March 2013

Science.gov (United States)

Davis, Tracy A.; Olsen, Lisa D.; Fram, Miranda S.; Belitz, Kenneth

2014-01-01

Groundwater samples have been collected in California as part of statewide investigations of groundwater quality conducted by the U.S. Geological Survey for the Groundwater Ambient Monitoring and Assessment (GAMA) Priority Basin Project (PBP). The GAMA-PBP is being conducted in cooperation with the California State Water Resources Control Board to assess and monitor the quality of groundwater resources used for drinking-water supply and to improve public knowledge of groundwater quality in California. Quality-control samples (source-solution blanks, equipment blanks, and field blanks) were collected in order to ensure the quality of the groundwater sample results. Olsen and others (2010) previously determined study reporting levels (SRLs) for trace-element results based primarily on field blanks collected in California from May 2004 through January 2008. SRLs are raised reporting levels used to reduce the likelihood of reporting false detections attributable to contamination bias. The purpose of this report is to identify any changes in the frequency and concentrations of detections in field blanks since the last evaluation and update the SRLs for more recent data accordingly. Constituents analyzed were aluminum (Al), antimony (Sb), arsenic (As), barium (Ba), beryllium (Be), boron (B), cadmium (Cd), chromium (Cr), cobalt (Co), copper (Cu), iron (Fe), lead (Pb), lithium (Li), manganese (Mn), molybdenum (Mo), nickel (Ni), selenium (Se), silver (Ag), strontium (Sr), thallium (Tl), tungsten (W), uranium (U), vanadium (V), and zinc (Zn). Data from 179 field blanks and equipment blanks collected from March 2006 through March 2013 by the GAMA-PBP indicated that for trace elements that had a change in detection frequency and concentration since the previous review, the shift occurred near October 2009, in conjunction with a change in the capsule filters used by the study. Results for 89 field blanks and equipment blanks collected from October 2009 through March 2013 were

Toxic trace elements in Chilean seafoods

International Nuclear Information System (INIS)

De Gregori, I.; Delgado, D.; Pinochet, H.; Gras, N.; Thieck, M.; Munoz, L.; Bruhn, C.; Navarrete, G.

1992-01-01

Chile is a well known producer and exporter of shell fish. These seafoods, like other specimens of marine origin, are susceptible to environmental and other contaminations like trace elements, including toxicants. Therefore adequate analytical quality assurance is mandatory before accepting analytical results. In this context, use of at least 2 independent methods of determination and validation with certified reference materials (CRM) provides acceptable criteria for judging the reliability of the data. This paper describes sample treatments and analytical procedures for Cd, Cu and Hg determinations in mollusc samples. Three independent analytical techniques, namely differential pulse anodic stripping voltammetry, neutron activation analysis and atomic absorption spectrometry, were used. CRM standards of the IAEA, NIST and BCR were analyzed to evaluate quality assurance. Following the quality control phase, the concentrations of cadmium, copper, and mercury in fresh and canned mollusc samples Tagelus dombeii and Semelle solida (Navajuelas and Almejas chilenas respectively) from different locations were determined. (author). 32 refs.; 4 figs.; 7 tabs

Health Risk Assessment of Trace Metals in Various Environmental Media, Crops and Human Hair from a Mining Affected Area

Directory of Open Access Journals (Sweden)

Wushuang Xie

2017-12-01

Full Text Available Long term exposure to trace metals in various media is of great concern for people living in known pollution sources, such as mining and industrial activities. Health risk assessment and human hair analysis can provide important information for local environmental management. Information on distribution characteristics of trace metals in soil, water, sediment, air, local crops, and human hair from a typical mining area in southern China was collected. Results show there exists severely trace metal contamination in soil, sediment, and air. Arsenic and Pb contents in the local children’s hair are higher than the upper reference values, and the accumulation of residents’ hair trace metals shows great correlation with the ingestion and inhalation pathways. Arsenic contributes 52.27% and 58.51% to the total non-cancer risk of adults and children, respectively. The cancer risk of Cd in adults and children are 4.66 and 3.22 times higher than the safe level, respectively. Ingestion exposure pathway of trace metals largely contributes to the total non-cancer and cancer effect. The metals As, Cd, and Pb are major risk sources and pollutants that should be given priority for management, and ingestion pathway exposure to trace metals through soil and crops should be controlled.

Removal of trace organic contaminants by an MBR comprising a mixed culture of bacteria and white-rot fungi.

Science.gov (United States)

Nguyen, Luong N; Hai, Faisal I; Yang, Shufan; Kang, Jinguo; Leusch, Frederic D L; Roddick, Felicity; Price, William E; Nghiem, Long D

2013-11-01

The degradation of 30 trace organic contaminants (TrOC) by a white-rot fungus-augmented membrane bioreactor (MBR) was investigated. The results show that white-rot fungal enzyme (laccase), coupled with a redox mediator (1-hydroxy benzotriazole, HBT), could degrade TrOC that are resistant to bacterial degradation (e.g. diclofenac, triclosan, naproxen and atrazine) but achieved low removal of compounds (e.g. ibuprofen, gemfibrozil and amitriptyline) that are well removed by conventional activated sludge treatment. Overall, the fungus-augmented MBR showed better TrOC removal compared to a system containing conventional activated sludge. The major role of biodegradation in removal by the MBR was noted. Continuous mediator dosing to MBR may potentially enhance its performance, although not as effectively as for mediator-enhanced batch laccase systems. A ToxScreen3 assay revealed no significant increase in the toxicity of the effluent during MBR treatment of the synthetic wastewater comprising TrOC, confirming that no toxic by-products were produced. Copyright © 2013 Elsevier Ltd. All rights reserved.

Techniques for the measurement of trace moisture in high-purity electronic specialty gases

International Nuclear Information System (INIS)

Funke, Hans H.; Grissom, Brad L.; McGrew, Clark E.; Raynor, Mark W.

2003-01-01

The control of water vapor (moisture) contamination in process gases is critical to the successful manufacture of semiconductor devices. As specified moisture levels have become more stringent, there is a growing demand for more sensitive analytical methods. Instrumental methods currently being used or in development for measuring trace moisture at ppbv levels include Fourier transform infrared spectroscopy, tunable diode laser absorption spectroscopy, cavity ringdown spectroscopy, intracavity laser spectroscopy, electron impact ionization mass spectrometry, and atmospheric pressure ionization mass spectrometry. In addition, sensor-based technologies such as oscillating quartz crystal microbalances, and chilled mirror-, capacitor-, and electrolytic-based hygrometers operate in this regime. These approaches are presented and reviewed. As the success of each trace moisture method is dependent on the degree to which the different process gases interfere with the measurement process, important process gas applications of the techniques are highlighted. Advantages and disadvantages as well as future developments and trends are also presented

The Barents Sea, distribution and fate of radioactive contaminants

International Nuclear Information System (INIS)

Foeyn, L.; Heldal, H.E.; Svaeren, I.

1999-01-01

Possible contamination in the marine food webs of the Barents Sea may be a problem for a rational harvest of the area. Radioactive contamination has in this context a special public impact as even traces of radioactivity seems to be considered by the public to be a real danger. It is therefor of special importance, from a regulatory and fisheries point of view, to accumulate knowledge of the behaviour of radioactive elements in the marine ecosystems of the Barents Sea in order to place this contamination in proper and realistic proportions

Optimizing the molarity of a EDTA washing solution for saturated-soil remediation of trace metal contaminated soils

International Nuclear Information System (INIS)

Andrade, M.D.; Prasher, S.O.; Hendershot, W.H.

2007-01-01

Three experiments were conducted to optimize the use of ethylenediaminetetraacetic acid (EDTA) for reclaiming urban soils contaminated with trace metals. As compared to Na 2 EDTA (NH 4 ) 2 EDTA extracted 60% more Zn and equivalent amounts of Cd, Cu and Pb from a sandy loam. When successively saturating and draining loamy sand columns during a washing cycle, which submerged it once with a (NH 4 ) 2 EDTA wash and four times with deionised water, the post-wash rinses largely contributed to the total cumulative extraction of Cd, Co, Cr, Cu, Mn, Ni, Pb and Zn. Both the washing solution and the deionised water rinses were added in a 2:5 liquid to soil (L:S) weight ratio. For equal amounts of EDTA, concentrating the washing solution and applying it and the ensuing rinses in a smaller 1:5 L:S weight ratio, instead of a 2:5 L:S weight ratio, increased the extraction of targeted Cr, Cu, Ni, Pb and Zn. - A single EDTA addition is best utilised in a highly concentrated washing solution given in a small liquid to soil weight ratio

Control of the surface radioactive contamination in the field of biological research

International Nuclear Information System (INIS)

Calvo, S.; Encina, A. de la; Gaspar, J.; Macias, M. T.; Sanchez, A.; Usera, F.

2012-01-01

The manipulation of unsealed sources in biomedical research involves significant risk of radioactive contamination. the aim of this study has been to analyze the radioactive contamination occurring in the field of biomedical research, assessing its magnitude, identifying the equipment that can be contaminated with higher probability and monitoring the evolution of the contaminations production taking into account the radioisotopes and the activities uses, and the radiation protection control applied. The data used for this study correspond to a very lengthy period of time and it have been collected in the radioactive facility, of the Centro Nacional de Biotecnologia (CSIC), a very large biological research centre that can be used perfectly as a reference for this area. The results obtained show a gradual and significant decrease in the incidence of the radioactive contamination. This is due to the optimization of radiation protection standards applied and the implementation or a systematic operational radiation protection program. (Author) 13 refs.

Radiation protection at the RA Reactor in 1985, Part -2, Annex 2b, Environmental Radioactivity control, Control of air contamination

International Nuclear Information System (INIS)

Patic, D.; Smiljanic, R.; Zaric, M.; Savic, Z.; Ristic, D.

1985-01-01

During the period from November 1984 - November 1985, within the radioactivity control on the Vinca Institute site air contamination radioactive aerosol contents was measured. Control was done on 4 measuring stations, two in the Institute and two locations in the direction of wind i.e. Belgrade, 2 km and 7 km away from the Institute respectively. This position of the measuring locations enables control of radiation safety of the Institute, as well as environment of Belgrade taking into account the existence of the reactor and other possible contaminants in the Institute [sr

Distribution of toxic trace elements in soil/sediment in post-Katrina New Orleans and the Louisiana Delta

International Nuclear Information System (INIS)

Su Tingzhi; Shu Shi; Shi Honglan; Wang Jianmin; Adams, Craig; Witt, Emitt C.

2008-01-01

This study provided a comprehensive assessment of seven toxic trace elements (As, Pb, V, Cr, Cd, Cu, and Hg) in the soil/sediment of Katrina affected greater New Orleans region 1 month after the recession of flood water. Results indicated significant contamination of As and V and non-significant contamination of Cd, Cr, Cu, Hg and Pb at most sampling sites. Compared to the reported EPA Region 6 soil background inorganic levels, except As, the concentrations of other six elements had greatly increased throughout the studied area; St. Bernard Parish and Plaquemines Parish showed greater contamination than other regions. Comparison between pre- and post-Katrina data in similar areas, and data for surface, shallow, and deep samples indicated that the trace element distribution in post-Katrina New Orleans was not obviously attributed to the flooding. This study suggests that more detailed study of As and V contamination at identified locations is needed. - This article provides an in-depth assessment of the contamination of As, Pb, V, Cr, Cd, Cu, and Hg in post-Katrina greater New Orleans region

Real-time beam tracing for control of the deposition location of electron cyclotron waves

Energy Technology Data Exchange (ETDEWEB)

Reich, M., E-mail: matthias.reich@ipp.mpg.de; Bilato, R.; Mszanowski, U.; Poli, E.; Rapson, C.; Stober, J.; Volpe, F.; Zille, R.

2015-11-15

Highlights: • We successfully integrated a real-time EC beam tracing code at ASDEX Upgrade. • The calculation of EC beam deposition location is fast enough for control purposes. • The accuracy of the deposition location calculation exceeds equivalent measurements. • The implementation method is by design portable to larger fusion devices. - Abstract: Plasma control techniques that use electron cyclotron (EC) resonance heating and current drive such as control of neoclassical tearing modes require accurate control of the deposition location of EC beams. ASDEX Upgrade has successfully implemented a real-time version of the beam-tracing code TORBEAM into its real-time diagnostic system to act as a globally available module that calculates current deposition location and its sensitivity from other real-time diagnostic measurements for all its moveable EC wave launchers. Based on a highly (100×) accelerated version of TORBEAM, the software implementation as a diagnostic process uses parallelization and achieves cycle times of 15–20 ms for determining the radial deposition location of 12 beams in the plasma. This cycle time includes data input–output overhead arising from the use of available real-time signals. The system is by design portable to other machines such as ITER.

Contamination control - the analysis of things as they should be

International Nuclear Information System (INIS)

Stewart, R.B.

Contamination can be controlled in chemical analyses by the use of suitable containers, cleanliness, appropriate apparatus design, isolation of the analysis process from air, and in-situ analysis. Examples based on analyses of organic reactor coolant, metals, and underground natural waters are given. (LL)

Automatic parameter estimation of multicompartmental neuron models via minimization of trace error with control adjustment.

Science.gov (United States)

Brookings, Ted; Goeritz, Marie L; Marder, Eve

2014-11-01

We describe a new technique to fit conductance-based neuron models to intracellular voltage traces from isolated biological neurons. The biological neurons are recorded in current-clamp with pink (1/f) noise injected to perturb the activity of the neuron. The new algorithm finds a set of parameters that allows a multicompartmental model neuron to match the recorded voltage trace. Attempting to match a recorded voltage trace directly has a well-known problem: mismatch in the timing of action potentials between biological and model neuron is inevitable and results in poor phenomenological match between the model and data. Our approach avoids this by applying a weak control adjustment to the model to promote alignment during the fitting procedure. This approach is closely related to the control theoretic concept of a Luenberger observer. We tested this approach on synthetic data and on data recorded from an anterior gastric receptor neuron from the stomatogastric ganglion of the crab Cancer borealis. To test the flexibility of this approach, the synthetic data were constructed with conductance models that were different from the ones used in the fitting model. For both synthetic and biological data, the resultant models had good spike-timing accuracy. Copyright © 2014 the American Physiological Society.

Eco-toxicity and metal contamination of paddy soil in an e-wastes recycling area

International Nuclear Information System (INIS)

Zhang Junhui; Hang Min

2009-01-01

Paddy soil samples taken from different sites in an old primitive electronic-waste (e-waste) processing region were examined for eco-toxicity and metal contamination. Using the environmental quality standard for soils (China, Grade II) as reference, soil samples of two sites were weakly contaminated with trace metal, but site G was heavily contaminated with Cd (6.37 mg kg -1 ), and weakly contaminated with Cu (256.36 mg kg -1 ) and Zn (209.85 mg kg -1 ). Zn appeared to be strongly bound in the residual fraction (72.24-77.86%), no matter the soil was metal contaminated or not. However, more than 9% Cd and 16% Cu was present in the non-residual fraction in the metal contaminated soils than in the uncontaminated soil, especially for site G and site F. Compared with that of the control soil, the micronucleus rates of site G and site F soil treatments increased by 2.7-fold and 1.7-fold, respectively. Low germination rates were observed in site C (50%) and site G (50%) soil extraction treated rice seeds. The shortest root length (0.2377 cm) was observed in site G soil treated groups, which is only 37.57% of that of the control soil treated groups. All of the micronucleus ratio of Vicia faba root cells, rice germination rate and root length after treatment of soil extraction indicate the eco-toxicity in site F and G soils although the three indexes are different in sensitivity to soil metal contamination.

Trace element analysis of soil type collected from the Manjung and central Perak

Energy Technology Data Exchange (ETDEWEB)

Azman, Muhammad Azfar, E-mail: m-azfar@nuclearmalaysia.gov.my; Hamzah, Suhaimi; Rahman, Shamsiah Abdul; Elias, Md Suhaimi; Abdullah, Nazaratul Ashifa; Hashim, Azian; Shukor, Shakirah Abd; Kamaruddin, Ahmad Hasnulhadi Che [Blok 18, Makmal Analisis Kimia (Aca/Bas), Agensi Nuklear Malaysia, 43000 Kajang, Selangor (Malaysia)

2015-04-29

Trace elements in soils primarily originated from their parent materials. Parents’ material is the underlying geological material that has been undergone different types of chemical weathering and leaching processes. Soil trace elements concentrations may be increases as a result of continuous input from various human activities, including power generation, agriculture, mining and manufacturing. This paper describes the Neutron Activation Analysis (NAA) method used for the determination of trace elements concentrations in part per million (ppm) present in the terrestrial environment soil in Perak. The data may indicate any contamination of trace elements contributed from human activities in the area. The enrichment factors were used to check if there any contamination due to the human activities (power plants, agricultural, mining, etc.) otherwise the values would serve as a baseline data for future study. The samples were collected from 27 locations of different soil series in the area at two different depths: the top soil (0-15cm) and the sub soil (15-30cm). The collected soil samples were air dried at 60°C and passed through 2 µm sieve. Instrumental Neutron Activation Analysis (NAA) has been used for the determination of trace elements. Samples were activated in the Nuclear Malaysia TRIGA Mark II reactor followed by gamma spectrometric analysis. By activating the stable elements in the samples, the elements can be determined from the intensities of gamma energies emitted by the respected radionuclides.

Trace elements in high purity materials for advanced technology: contribution of neutron activation analysis and radioanalytical technique

International Nuclear Information System (INIS)

Gallorini, M.; Pietra, R.; Sabbioni, E.

1991-01-01

Neutron activation analysis and radioanalytical techniques have been employed to investigate problems related to trace elements and high purity technology materials. Applications of these techniques are overviewed: semiconductor technology as in the case of As and In ion implantation in high purity silicon; problems related to trace elements impurities in thermometric measurements; coating materials to prevent trace elements contamination in biological sampling and metals release from human prostheses. (author) 8 refs.; 2 figs.; 8 tabs

Contaminated nickel scrap processing

Energy Technology Data Exchange (ETDEWEB)

Compere, A.L.; Griffith, W.L.; Hayden, H.W.; Johnson, J.S. Jr.; Wilson, D.F.

1994-12-01

The DOE will soon choose between treating contaminated nickel scrap as a legacy waste and developing high-volume nickel decontamination processes. In addition to reducing the volume of legacy wastes, a decontamination process could make 200,000 tons of this strategic metal available for domestic use. Contaminants in DOE nickel scrap include {sup 234}Th, {sup 234}Pa, {sup 137}Cs, {sup 239}Pu (trace), {sup 60}Co, U, {sup 99}Tc, and {sup 237}Np (trace). This report reviews several industrial-scale processes -- electrorefining, electrowinning, vapormetallurgy, and leaching -- used for the purification of nickel. Conventional nickel electrolysis processes are particularly attractive because they use side-stream purification of process solutions to improve the purity of nickel metal. Additionally, nickel purification by electrolysis is effective in a variety of electrolyte systems, including sulfate, chloride, and nitrate. Conventional electrorefining processes typically use a mixed electrolyte which includes sulfate, chloride, and borate. The use of an electrorefining or electrowinning system for scrap nickel recovery could be combined effectively with a variety of processes, including cementation, solvent extraction, ion exchange, complex-formation, and surface sorption, developed for uranium and transuranic purification. Selected processes were reviewed and evaluated for use in nickel side-stream purification. 80 refs.

Earth Observing System/Meteorological Satellite (EOS/METSAT). Advanced Microwave Sounding Unit-A (AMSU-A) Contamination Control Plan

Science.gov (United States)

Fay, M.

1998-01-01

This Contamination Control Plan is submitted in response the Contract Document requirements List (CDRL) 007 under contract NAS5-32314 for the Earth Observing System (EOS) Advanced Microwave Sounding Unit A (AMSU-A). In response to the CDRL instructions, this document defines the level of cleanliness and methods/procedures to be followed to achieve adequate cleanliness/contamination control, and defines the required approach to maintain cleanliness/contamination control through shipping, observatory integration, test, and flight. This plan is also applicable to the Meteorological Satellite (METSAT) except where requirements are identified as EOS-specific. This plan is based on two key factors: a. The EOS/METSAT AMSU-A Instruments are not highly contamination sensitive. b. Potential contamination of other EOS Instruments is a key concern as addressed in Section 9/0 of the Performance Assurance Requirements for EOS/METSAT Integrated Programs AMSU-A Instrument (MR) (NASA Specification S-480-79).

Effective radiological contamination control and monitoring techniques in high alpha environments.

Science.gov (United States)

Funke, Kevin C

2003-02-01

In the decommissioning of a highly contaminated alpha environment, such as the one at Hanford's 233-S Plutonium Concentration Facility, one of the key elements of a successful radiological control program is an integrated safety approach. This approach begins with the job-planning phase where the scope of the work is described. This is followed by a brainstorming session involving engineering and craft to identify how to perform the work in a logical sequence of events. Once the brainstorming session is over, a Job Hazard Analysis is performed to identify any potential problems. Mockups are utilized to enable the craft to get hands on experience and provide feedback and ideas to make the job run smoother. Ideas and experience gained during mockups are incorporated into the task instruction. To assure appropriate data are used in planning and executing the job, our principal evaluation tools included lapel and workplace air sampling, plus continuous air monitors and frequent surveys to effectively monitor job progress. In this highly contaminated alpha environment, with contamination levels ranging from 0.3 Bq cm-2 to approximately 100,000 Bq cm-2 (2,000 dpm per 100 cm2 to approximately 600 million dpm per 100 cm2), with average working levels of 1,600-3,200 Bq cm-2 (10-20 million dpm per 100 cm2) without concomitant ambient radiation levels, control of the spread of contamination is key to keeping airborne levels As Low As Reasonably Achievable.

Rapid diffusion of molybdenum trace contamination in silicon

International Nuclear Information System (INIS)

Tobin, S.P.; Greenwald, A.C.; Wolfson, R.G.; Meier, D.L.; Drevinsky, P.J.

1985-01-01

Molybdenum contamination has been detected in silicon epitaxial layers and substrate wafers after processing in any one of several epitaxial silicon reactors. Greatly reduced minority carrier diffusion lengths and lifetimes are consistent with Mo concentrations measured by DLTS in the 10 12 and 10 13 cm -3 ranges. Depth profiling of diffusion length and the Mo deep level show much greater penetration than expected from previous reports of Mo as a slow diffuser. The data indicate a lower limit of 10 -8 cm 2 /sec for the diffusion coefficient of Mo in silicon at 1200 0 C, consistent with high diffusivities measured for other transition metals

Modeling of contact tracing in social networks

Science.gov (United States)

Tsimring, Lev S.; Huerta, Ramón

2003-07-01

Spreading of certain infections in complex networks is effectively suppressed by using intelligent strategies for epidemic control. One such standard epidemiological strategy consists in tracing contacts of infected individuals. In this paper, we use a recently introduced generalization of the standard susceptible-infectious-removed stochastic model for epidemics in sparse random networks which incorporates an additional (traced) state. We describe a deterministic mean-field description which yields quantitative agreement with stochastic simulations on random graphs. We also discuss the role of contact tracing in epidemics control in small-world and scale-free networks. Effectiveness of contact tracing grows as the rewiring probability is reduced.

Trace element assessment in water of river kassa system, jos ...

African Journals Online (AJOL)

The value of index of geoaccumulation (Igeo) is approximately 2; for Zn and Pb which indicates, moderate contamination. Areas of the river system with anomalous value of trace element concentrations are those where mine tailings have been deposited close to the river channel or places where run off from adjoining ...

Method for removing trace contaminants from multicurie amounts of 144Ce

International Nuclear Information System (INIS)

Wagner, J.A.; Kanapilly, G.M.

1976-01-01

Removal of contaminants from stock solutions of 144 Ce(III) was required for large quantities of 144 Ce prior to incorporation into fused aluminosilicate particles for inhalation toxicology studies. Since available procedures for purification of 144 Ce could not be readily adapted to our laboratory conditions and requirements, a simple procedure was developed to purify 144 Ce in multicurie quantities of 144 Ce(III). This procedure consists of separation of 144 Ce from contaminants by precipitation and filtrations at different pH. Its simplicity and efficacy in providing a stock solution that would readily exchange into montmorillonite clay was demonstrated when it was used during the preparation of large amounts of 144 Ce in fused aluminosilicate particles

The effects of mediator and granular activated carbon addition on degradation of trace organic contaminants by an enzymatic membrane reactor.

Science.gov (United States)

Nguyen, Luong N; Hai, Faisal I; Price, William E; Leusch, Frederic D L; Roddick, Felicity; Ngo, Hao H; Guo, Wenshan; Magram, Saleh F; Nghiem, Long D

2014-09-01

The removal of four recalcitrant trace organic contaminants (TrOCs), namely carbamazepine, diclofenac, sulfamethoxazole and atrazine by laccase in an enzymatic membrane reactor (EMR) was studied. Laccases are not effective for degrading non-phenolic compounds; nevertheless, 22-55% removal of these four TrOCs was achieved by the laccase EMR. Addition of the redox-mediator syringaldehyde (SA) to the EMR resulted in a notable dose-dependent improvement (15-45%) of TrOC removal affected by inherent TrOC properties and loading rates. However, SA addition resulted in a concomitant increase in the toxicity of the treated effluent. A further 14-25% improvement in aqueous phase removal of the TrOCs was consistently observed following a one-off dosing of 3g/L granular activated carbon (GAC). Mass balance analysis reveals that this improvement was not due solely to adsorption but also enhanced biodegradation. GAC addition also reduced membrane fouling and the SA-induced toxicity of the effluent. Copyright © 2014 Elsevier Ltd. All rights reserved.

Identification by genotyping of a commercial antigen preparation as the source of a laboratory contamination with Coxiella burnetii and as an unexpected rich source of control DNA

NARCIS (Netherlands)

Tilburg, Jeroen J. H. C.; Horrevorts, Alphons M.; Peeters, Marcel F.; Klaassen, Corne H. W.; Rossen, John W. A.

By performing genotyping, a laboratory contamination involving Q fever was traced back to the antigen preparation used in a commercially available complement fixation test. It was established that such antigen preparations contain relatively high loads of DNA/RNA, making them potential sources of

Radioactive surface contamination monitors

International Nuclear Information System (INIS)

Aoyama, Kei; Minagoshi, Atsushi; Hasegawa, Toru

1994-01-01

To reduce radiation exposure and prevent contamination from spreading, each nuclear power plant has established a radiation controlled area. People and articles out of the controlled area are checked for the surface contamination of radioactive materials with surface contamination monitors. Fuji Electric has repeatedly improved these monitors on the basis of user's needs. This paper outlines typical of a surface contamination monitor, a personal surface contamination monitor, an article surface contamination monitor and a laundry monitor, and the whole-body counter of an internal contamination monitor. (author)

Control apparatus for radioactive contamination of the filtering device adapted on the protection apparatus of the respiratory tracts (1961); Appareil de controle de la contamination radioactive des dispositifs filtrants adaptes sur les appareils de protection des voies respiratoires (1961)

Energy Technology Data Exchange (ETDEWEB)

Dujancourt, S; Roche, J [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

1961-07-01

That apparatus allows to detect and localize the radioactive contamination of the mask cartridge, for alpha, beta and gamma radiations, concerning external contamination, and for beta and gamma radiations, concerning internal contamination. It consists of lead coffin, in which the cartridge is inserted for control. Halogen counters are in contact with it. Operation conditions (Geiger or proportional) and their position on regard to the cartridge are controlled from outside. A sealer counts the pulses, given by the different counters. (authors) [French] Cet appareil permet de detecter et de localiser la contamination radioactive de cartouches filtrantes de masques, en {alpha}, {beta} et {gamma}, en ce qui concerne la contamination exterieure, et en {beta} et {gamma} en ce qui concerne la contamination interieure. Il est constitue par un coffre en plomb dans lequel est introduite la cartouche a controler. Des compteurs halogenes sont au contact de celle-ci. Leur regime de fonctionnement (Geiger ou proportionnel) et leur position par rapport a la cartouche sont commandes de l'exterieur. Une echelle de comptage compte les impulsions donnees par les differents compteurs. (auteurs)

Trace Elements Contamination and Human Health Risk Assessment in Drinking Water from the Agricultural and Pastoral Areas of Bay County, Xinjiang, China

Directory of Open Access Journals (Sweden)

Muyessar Turdi

2016-09-01

Full Text Available Tap water samples were collected from 180 families in four agricultural (KYR: Keyir, KRW: Kariwak, YTR: Yatur, DW: Dawanqi and two pastoral areas (B: Bulong and Y: Yangchang in Bay County, Xinjiang, China, and levels of seven trace elements (Cd, Cr, As Ni, Pb, Zn, Se were analyzed using inductively-coupled plasma mass spectrometry (ICP-MS to assess potential health risks. Remarkable spatial variations of contamination were observed. Overall, the health risk was more severe for carcinogenic versus non-carcinogenic pollutants due to heavy metal. The risk index was greater for children overall (Cr > As > Cd and Zn > Se for carcinogenic and non-carcinogenic elements, respectively. The total risk index was greater in agricultural areas (DW > KYR > YTR > KRW > B > Y. Total risk indices were greater where well water was the source versus fountain water; for the latter, the total health risk index was greater versus glacier water. Main health risk factors were Cr and As in DW, KYR, YTR, KRW, and B, and Zn, Cr, and As in the Y region. Overall, total trace element–induced health risk (including for DW adults was higher than acceptable (10−6 and lower than priority risk levels (10−4 (KYR, YTR, KRW, Y, and B. For DW children, total health risk reached 1.08 × 10−4, higher than acceptable and priority risk levels (10−4.

Trace Elements Contamination and Human Health Risk Assessment in Drinking Water from the Agricultural and Pastoral Areas of Bay County, Xinjiang, China.

Science.gov (United States)

Turdi, Muyessar; Yang, Linsheng

2016-09-23

Tap water samples were collected from 180 families in four agricultural (KYR: Keyir, KRW: Kariwak, YTR: Yatur, DW: Dawanqi) and two pastoral areas (B: Bulong and Y: Yangchang) in Bay County, Xinjiang, China, and levels of seven trace elements (Cd, Cr, As Ni, Pb, Zn, Se) were analyzed using inductively-coupled plasma mass spectrometry (ICP-MS) to assess potential health risks. Remarkable spatial variations of contamination were observed. Overall, the health risk was more severe for carcinogenic versus non-carcinogenic pollutants due to heavy metal. The risk index was greater for children overall (Cr > As > Cd and Zn > Se for carcinogenic and non-carcinogenic elements, respectively). The total risk index was greater in agricultural areas (DW > KYR > YTR > KRW > B > Y). Total risk indices were greater where well water was the source versus fountain water; for the latter, the total health risk index was greater versus glacier water. Main health risk factors were Cr and As in DW, KYR, YTR, KRW, and B, and Zn, Cr, and As in the Y region. Overall, total trace element-induced health risk (including for DW adults) was higher than acceptable (10(-6)) and lower than priority risk levels (10(-4)) (KYR, YTR, KRW, Y, and B). For DW children, total health risk reached 1.08 × 10(-4), higher than acceptable and priority risk levels (10(-4)).

Persistence of Trace Organic Contaminants from a Commercial Biosolids-Based Fertilizer in Aerobic Soils

OpenAIRE

Banet, Travis A; Kim, Jihyun R; Mashtare, Michael L

2016-01-01

Municipal biosolids are recycled as agricultural fertilizers. Recent studies have raised concerns due to the presence of emerging contaminants in municipal biosolids. Previous research suggests that these contaminants have the potential to reside in biosolids-based fertilizers that are commercially distributed. Use of these products in urban/suburban areas may provide a pathway for these contaminants to enter ecosystems and impact human and environmental health. Soils from Purdue University’s...

Contamination control requirements implementation for the James Webb Space Telescope (JWST), part 2: spacecraft, sunshield, observatory, and launch

Science.gov (United States)

Wooldridge, Eve M.; Schweiss, Andrea; Henderson-Nelson, Kelly; Woronowicz, Michael; Patel, Jignasha; Macias, Matthew; McGregor, R. Daniel; Farmer, Greg; Schmeitzky, Olivier; Jensen, Peter; Rumler, Peter; Romero, Beatriz; Breton, Jacques

2014-09-01

This paper will continue from Part 1 of JWST contamination control implementation. In addition to optics, instruments, and thermal vacuum testing, JWST also requires contamination control for a spacecraft that must be vented carefully in order to maintain solar array and thermal radiator thermal properties; a tennis court-sized sunshield made with 1-2 mil Kapton™ layers that must be manufactured and maintained clean; an observatory that must be integrated, stowed and transported to South America; and a rocket that typically launches commercial payloads without contamination sensitivity. An overview of plans developed to implement contamination control for the JWST spacecraft, sunshield, observatory and launch vehicle will be presented.

Amendment application in a multicontaminated mine soil: Effects on trace element mobility

OpenAIRE

Manzano, Rebeca; Peñalosa, Jesús Manuel; Esteban, Elvira

2014-01-01

The final publication is available at Springer via http://dx.doi.org/10.1007/s11270-014-1874-4 Several amendments were tested for their effectiveness in aiding plant growth and immobilising contaminants in pots containing soil from an arsenopyrite mine contaminated with arsenic and heavy metals. Trace element solubility in pore water was monitored using Rhizon samplers for five weeks. Results showed that amendments containing ferrous sulphate and ferrous sulphate combined with paper mill l...

LASER SPECTROSCOPY AND TRACE ELEMENT ANALYSIS Chapter from the Energy and Environment Division Annual Report 1980

Energy Technology Data Exchange (ETDEWEB)

Various, Authors

1981-05-01

In order to control pollutants resulting from energy production and utilization, adequate methods are required for monitoring the level of various substances often present at low concentrations. The Energy and Environment Division Applied Research in Laser Spectroscopy & Analytical Techniques Program is directed toward meeting these needs, Emphasis is on the development of physical methods, as opposed to conventional chemical analysis techniques. The advantages, now widely recognized, include ultra-high sensitivity coupled with minimal sample preparation. In some instances physical methods provide multi-parameter measurements which often provide the only means of achiev·ing the sensitivity necessary for the detection of trace contaminants. Work is reported in these areas: APPLIED PHYSICS AND LASER SPECTROSCOPY RESEARCH; MICROPROCESSOR CONTROLLER ANODIC STRIPPING VOLTAMETER FOR TRACE METALS ANALYSIS IN WATER; THE SURVEY OF INSTRUMENTATION FOR ENVIRONMENTAL MONITORING; THE POSSIBLE CHRONDRITIC NATURE OF THE DANISH CRETACEOUS~TERTIARY BOUNDARY; IMPROVEMENT OF THE SENSITIVITY AND PRECISION OF NEUTRON ACTIVATION ANALYSIS OF SOME ELEMENTS IN PLANKTON AND PLANKTONIC FISH; and SOURCES OF SOME SECONDARILY WORKED OBSIDIAN ARTIFACTS FROM TIKAL, GUATEMALA.

The trace metals accumulation in marine organisms of the southeastern Adriatic coast, Montenegro

Directory of Open Access Journals (Sweden)

Joksimovic Danijela

2012-01-01

Full Text Available The concentration and accumulation of trace metals (Co, Ni, As, Cd, Pb and Hg were measured in sea water, sediments and marine organisms in the coastline of the Montenegro. The obtained results of trace metals in seagrass and mussels were compared with those found in the water column and sediment. Sampling was performed in the fall of 2005 at five locations in the Montenegrin coastline, Sveta Stasija, Herceg Novi, Zanjice, Budva and Bar, which present different levels and sources of human impact. The heavy metals analyses in seawater, sediment, P. oceanica and M. galloprovincialis identified the harbor of Bar as the most Hg-contaminated site, Zanjice as the most As contaminated and Sveta Stasija as the most Pb-contaminated areas of the Montenegrin coastal area. This study showed that P. oceanica may have a greater bioaccumulation capacity than M. galloprovincialis for the considered metals, except for As and Hg, and both organisms may reflect contamination in the water column and in the sediment. For the first time, seagrass P. oceanica and M. galloprovincialis were employed as metal bioindicators for the southeastern Adriatic. The results of this study could serve as a baseline in the future for the assessment of anthropogenic effects in this marine ecosystem.

Nondestructive indices of trace element exposure in squamate reptiles

Energy Technology Data Exchange (ETDEWEB)

Hopkins, W.A.; Roe, J.H.; Snodgrass, J.W.; Jackson, B.P.; Kling, D.E.; Rowe, C.L.; Congdon, J.D. [University of Georgia, Aiken, SC (USA). Savannah River Ecology Lab.

2001-07-01

Compared with birds, mammals, fish, and even amphibians, very little is known about the effects of contaminants on reptiles. The current study experimentally evaluated the utility of shed skins, tail clips, and blood samples as nondestructive indices of trace element exposure in banded water snakes, Nerodia fasciata. For 13.5 months, snakes were either fed fish from a coal ash-contaminated site or uncontaminated food from a reference site. Snakes fed contaminated prey accumulated As, Cd, Se, Sr, and V in various organs (i.e. liver, kidney, and/or gonads). Moreover, non-parametric discriminant function analysis revealed that snakes could be placed in two groups that reliably reflected their experimental diet based upon Se, Sr, and As concentrations in tail clips, blood, and/or shed skins. It is suggested that nondestructive sampling techniques, particularly analyses of blood and tail clips, may be easily applied in evaluations of contaminant exposure in the field and laboratory and may prevent excessive destructive sampling of potentially threatened reptile species.

A Synopsis of Technical Issues of Concern for Monitoring Trace Elements in Highway and Urban Runoff

Science.gov (United States)

Breault, Robert F.; Granato, Gregory E.

2000-01-01

elements and other sources of bias and variability in the sampling process. Trace elements have both natural and anthropogenic sources that may affect the sampling process, including the sample-collection and handling materials used in many trace-element monitoring studies. Trace elements also react with these materials within the timescales typical for collection, processing and analysis of runoff samples. To study the characteristics and potential effects of trace elements in highway and urban runoff, investigators typically sample one or more operationally defined matrixes including: whole water, dissolved (filtered water), suspended sediment, bottom sediment, biological tissue, and contaminant sources. The sampling and analysis of each of these sample matrixes can provide specific information about the occurrence and distribution of trace elements in runoff and receiving waters. There are, however, technical concerns specific to each matrix that must be understood and addressed through use of proper collection and processing protocols. Valid protocols are designed to minimize inherent problems and to maximize the accuracy, precision, comparability, and representativeness of data collected. Documentation, including information about monitoring protocols, quality assurance and quality control efforts, and ancillary data also is necessary to establish data quality. This documentation is especially important for evaluation of historical traceelement monitoring data, because trace-element monitoring protocols and analysis methods have been constantly changing over the past 30 years.

Ultra-trace analysis of hormones, pharmaceutical substances, alkylphenols and phthalates in two French natural mineral waters

Energy Technology Data Exchange (ETDEWEB)

Dévier, Marie-Hélène; Le Menach, Karyn [Environnements et Paléoenvironnements Océaniques et Continentaux (EPOC, UMR 5805 CNRS), Laboratoire de Physico- et Toxico-Chimie de l' Environnement (LPTC), Université de Bordeaux, 351 cours de la Libération, 33405 Talence cedex (France); Viglino, Liza [Danone Waters Analytical Center, Aqualab, Place de la Gare, 74500 Evian-Les-Bains (France); Di Gioia, Lodovico [Danone Research, R and D Waters Division, RD 128, 91767 Palaiseau Cedex (France); Lachassagne, Patrick [Danone Waters France, Environment and Water Resources Division, BP 87, 11 av. Général Dupas, 74500 Evian-Les-Bains cedex (France); Budzinski, Hélène, E-mail: h.budzinski@epoc.u-bordeaux1.fr [Environnements et Paléoenvironnements Océaniques et Continentaux (EPOC, UMR 5805 CNRS), Laboratoire de Physico- et Toxico-Chimie de l' Environnement (LPTC), Université de Bordeaux, 351 cours de la Libération, 33405 Talence cedex (France)

2013-01-15

The aim of this work was to investigate the potential presence of a broad range of organic compounds, such as hormones, alkylphenols, bisphenol A and phthalates, as well as pharmaceutical substances in two brands of bottled natural mineral waters (Evian and Volvic, Danone). The phthalates were determined by solid-phase microextraction coupled to gas chromatography–mass spectrometry (SPME-GC–MS) and the other compounds by liquid chromatography–tandem mass spectrometry (LC–MS/MS) or gas chromatography–mass spectrometry (GC–MS) after solid-phase extraction. The potential migration of alkylphenols, bisphenol A and phthalates from polyethylene terephthalate (PET) bottles was also investigated under standardized test conditions. Evian and Volvic natural mineral waters contain none of the around 120 targeted organic compounds. Traces of 3 pharmaceuticals (ketoprofen, salicylic acid, and caffeine), 3 alkylphenols (4-nonylphenol, 4-t-octylphenol, and 4-nonylphenol diethoxylate), and some phthalates including di(2-ethylhexyl)phthalate (DEHP) were detected in the samples, but they were also present in the procedural blanks at similar levels. The additional test procedures demonstrated that the few detected compounds originated from the background laboratory contamination. Analytical procedures have been designed both in the bottling factory and in the laboratory in order to investigate the sources of DEHP and to minimize to the maximum this unavoidable laboratory contamination. It was evidenced that no migration of the targeted compounds from bottles occurred under the test conditions. The results obtained in this study underline the complexity of reaching a reliable measure to qualify the contamination of a sample at ultra-trace level, in the field of very pure matrices. The analytical procedures involving glassware, equipment, hoods, and rooms specifically dedicated to trace analysis allowed us to reach reliable procedural limits of quantification at the ng

Ultra-trace analysis of hormones, pharmaceutical substances, alkylphenols and phthalates in two French natural mineral waters

International Nuclear Information System (INIS)

Dévier, Marie-Hélène; Le Menach, Karyn; Viglino, Liza; Di Gioia, Lodovico; Lachassagne, Patrick; Budzinski, Hélène

2013-01-01

The aim of this work was to investigate the potential presence of a broad range of organic compounds, such as hormones, alkylphenols, bisphenol A and phthalates, as well as pharmaceutical substances in two brands of bottled natural mineral waters (Evian and Volvic, Danone). The phthalates were determined by solid-phase microextraction coupled to gas chromatography–mass spectrometry (SPME-GC–MS) and the other compounds by liquid chromatography–tandem mass spectrometry (LC–MS/MS) or gas chromatography–mass spectrometry (GC–MS) after solid-phase extraction. The potential migration of alkylphenols, bisphenol A and phthalates from polyethylene terephthalate (PET) bottles was also investigated under standardized test conditions. Evian and Volvic natural mineral waters contain none of the around 120 targeted organic compounds. Traces of 3 pharmaceuticals (ketoprofen, salicylic acid, and caffeine), 3 alkylphenols (4-nonylphenol, 4-t-octylphenol, and 4-nonylphenol diethoxylate), and some phthalates including di(2-ethylhexyl)phthalate (DEHP) were detected in the samples, but they were also present in the procedural blanks at similar levels. The additional test procedures demonstrated that the few detected compounds originated from the background laboratory contamination. Analytical procedures have been designed both in the bottling factory and in the laboratory in order to investigate the sources of DEHP and to minimize to the maximum this unavoidable laboratory contamination. It was evidenced that no migration of the targeted compounds from bottles occurred under the test conditions. The results obtained in this study underline the complexity of reaching a reliable measure to qualify the contamination of a sample at ultra-trace level, in the field of very pure matrices. The analytical procedures involving glassware, equipment, hoods, and rooms specifically dedicated to trace analysis allowed us to reach reliable procedural limits of quantification at the ng

Microbiological quality control of single-walled carbon-nanotubes-coated surfaces experimentally contaminated

International Nuclear Information System (INIS)

Natalizi, T.; Frioni, A.; Passeri, D.; Pantanella, F.

2013-01-01

The emergence of new nanotechnologies involves the spreading of nanoparticles in various fields of human life. Nanoparticles in general and, more specifically, carbon nanotubes have been adopted for many practical approaches i.e.: coatings for medical devices, food process industry and drug delivery. Humans will be increasingly exposed to nanoparticles but the susceptibility of nanostructured materials to microbial colonization in process of manufacturing and storage has not been thoroughly considered. Therefore, the microbiological quality control of nanoparticles plays a pivotal role. Different analytical methods have been attempted for detecting bacterial population contaminating a surface, but no one can be considered fully appropriate. Here, BioTimer Assay (BTA) and conventional sonication followed by colony forming units method (S-CFU) were applied for microbiological quality control of single-walled carbon nanotubes (SWCNTs)-coated surfaces experimentally contaminated with Streptococcus mutans and Pseudomonas aeruginosa. Our results demonstrated that S-CFU is unreliable to actually determine the number of bacteria, contaminating abiotic surfaces, as it does not detach all adherent bacteria and kills part of the bacterial population. Instead, BTA is a reliable method to enumerate bacteria colonizing SWCNTs-coated surfaces and can be considered a useful tool for microbiological quality control of nanomaterials for human use.

Removal of low concentration contaminant species using photocatalysis

DEFF Research Database (Denmark)

Nielsen, Morten Godtfred; Vesborg, Peter Christian Kjærgaard; Hansen, Ole

2015-01-01

A photocatalytic model reactor system has been devised to assess the capacity and feasibility of a photocatalytic unit for the removal of trace amounts of organic contaminants in air. Realistic operating conditions are applied, and a mathematical model based on Langmuir–Hinselwood adsorbtion perm...

Survey of reference materials for trace elements, nuclides and organic microcontaminants

International Nuclear Information System (INIS)

Parr, R.M.; Stone, S.F.; Bel-Amakeletch, T.; Zeisler, R.

1998-01-01

The International Atomic Energy Agency (IAEA), in co-operation with the United Nations Environment Programme (UNEP), has recently prepared a survey on internationally available analytical reference materials for trace elements, nuclides and organic contaminants in biological, environmental and related matrices. The purpose is to help analysts to select reference materials for quality assurance that match as closely as possible, with respect to matrix type and concentrations of the measurands of interest, the ''real'' samples that are to be measured. The present version of the survey, which is available in the form of two cost-free printed volumes [1], contains over 10,000 certified and information values in 650 reference materials from 27 different producers. The 455 measurands listed include trace elements, major and minor elements, organic contaminants, organometallic compounds, radionuclides and stable isotopes. Currently, the database from which the survey has been produced is being modified and extended so as to make the data available in electronic form via the Internet. (orig.)

Forensic Luminol Blood Test for Preventing Cross-contamination in Dentistry: An Evaluation of a Dental School Clinic

Directory of Open Access Journals (Sweden)

Marcelo Carlos Bortoluzzi

2014-01-01

Conclusions: We suggest that the luminol method is suitable for identifying contamination with invisible blood traces and this method may be a useful tool to prevent cross-contamination in the dental care setting.

Quantitative Structure--Activity Relationship (QSAR) for the Oxidation of Trace Organic Contaminants by Sulfate Radical.

Science.gov (United States)

Xiao, Ruiyang; Ye, Tiantian; Wei, Zongsu; Luo, Shuang; Yang, Zhihui; Spinney, Richard

2015-11-17

The sulfate radical anion (SO4•–) based oxidation of trace organic contaminants (TrOCs) has recently received great attention due to its high reactivity and low selectivity. In this study, a meta-analysis was conducted to better understand the role of functional groups on the reactivity between SO4•– and TrOCs. The results indicate that compounds in which electron transfer and addition channels dominate tend to exhibit a faster second-order rate constants (kSO4•–) than that of H–atom abstraction, corroborating the SO4•– reactivity and mechanisms observed in the individual studies. Then, a quantitative structure activity relationship (QSAR) model was developed using a sequential approach with constitutional, geometrical, electrostatic, and quantum chemical descriptors. Two descriptors, ELUMO and EHOMO energy gap (ELUMO–EHOMO) and the ratio of oxygen atoms to carbon atoms (#O:C), were found to mechanistically and statistically affect kSO4•– to a great extent with the standardized QSAR model: ln kSO4•– = 26.8–3.97 × #O:C – 0.746 × (ELUMO–EHOMO). In addition, the correlation analysis indicates that there is no dominant reaction channel for SO4•– reactions with various structurally diverse compounds. Our QSAR model provides a robust predictive tool for estimating emerging micropollutants removal using SO4•– during wastewater treatment processes.

Dynamics of metallic contaminants at a basin scale--Spatial and temporal reconstruction from four sediment cores (Loire fluvial system, France).

Science.gov (United States)

Dhivert, E; Grosbois, C; Courtin-Nomade, A; Bourrain, X; Desmet, M

2016-01-15

From the 19th century, the Loire basin (France) presents potentially pollutant activities such as mining and heavy industries. This paper shows spatio-temporal distribution of trace elements in sediments at a basin-scale, based on a comparison of archived temporal signals recorded in four sedimentary cores. Anthropogenic sources contributing to sediment contamination are also characterized, using geochemical signatures recorded in river bank sediments of the most industrialized tributaries. This study highlights upstream-downstream differences concerning recorded contamination phases in terms of spatial influence and temporality of archiving processes. Such differences were related to (i) various spatial influences of contamination sources and (ii) polluted sediments dispersion controlled by transport capacity of metal-carrier phases and hydrosedimentary dynamics. Copyright © 2015 Elsevier B.V. All rights reserved.

Trace metal distribution in sediments of the Pearl River Estuary and the surrounding coastal area, South China

International Nuclear Information System (INIS)

Ip, Carman C.M.; Li Xiangdong; Zhang Gan; Wai, Onyx W.H.; Li, Y.-S.

2007-01-01

Surface sediments and sediment cores collected at the Pearl River Estuary (PRE) and its surrounding coastal area were analysed for total metal concentrations, chemical partitioning, and Pb isotopic compositions. The distribution of Cu, Cr, Pb, and Zn demonstrated a typical diffusion pattern from the land to the direction of the sea. Two hotspots of trace metal contamination were located at the mixed zone between freshwater and marine waters. The enrichment of metals in the sediments could be attributed to the deposition of the dissolved and particulate trace metals in the water column at the estuarine area. The similar Pb isotopic signatures of the sediments at the PRE and its surrounding coastal area offered strong evidence that the PRE was a major source of trace metals to the adjacent coastal area. Slightly lower 206 Pb/ 207 Pb ratios in the coastal sediments may indicate other inputs of Pb in addition to the PRE sources, including the inputs from Hong Kong and other parts of the region. - The distribution of trace metals in sediments reflected contaminant sources, physical and chemical deposition processes

Evaluating cleansing effects on trace elements and stable isotope values in feathers of oiled birds.

Science.gov (United States)

Valladares, Sonia; Moreno, Roćio; Jover, Lluis; Sanpera, Carola

2010-01-01

Feathers of seabirds are widely used as a nondestructive tissue for pollution monitoring of trace elements, as well as convenient samples for trophic ecology studies by means of stable isotope analysis (SIA). Nevertheless, feathers can be occasionally impregnated with oil from deliberate ship discharges and from massive oil spill accidents. The feather structure makes them effective traps for particles and are subject to external contamination. It is unknown to what extent the oil adhered to feathers can change trace element concentrations or stable isotope signatures. This study has two primary objectives: (1) to assess if there are differences between trace element concentrations and stable isotope signatures of oiled and clean feathers, and (2) to determine if the cleansing of oiled feathers using commonly applied techniques such as sodium hydroxide (NaOH) washes in combination with an organic solvent (hexane) is more effective than using NaOH alone. In order to do this, we analysed trace elements (Se, Hg, Pb, Cu and Zn) and stable isotopes (delta(13)C and delta(15)N) of individual feathers of yellow-legged gulls (Larus michahellis) which were affected by the 2002 Prestige oil spill in Galicia (NW Spain). Two sets of feathers were analysed, one group were oil-free (Control group) and the other had oil adhered to its surface (Oiled group). We expected to find differences between control and oiled feathers when cleaning exclusively with NaOH and no differences when using hexane. Our results did not show significant differences between Control and Oiled groups as a consequence of the cleansing method used. Unexpectedly, the additional cleansing with hexane resulted in decreasing selenium concentrations and increasing zinc and delta(15)N values in all groups of feathers.

Active airborne contamination control using electrophoresis

International Nuclear Information System (INIS)

Veatch, B.D.

1994-01-01

In spite of our best efforts, radioactive airborne contamination continues to be a formidable problem at many of the Department of Energy (DOE) weapons complex sites. For workers that must enter areas with high levels of airborne contamination, personnel protective equipment (PPE) can become highly restrictive, greatly diminishing productivity. Rather than require even more restrictive PPE for personnel in some situations, the Rocky Flats Plant (RFP) is actively researching and developing methods to aggressively combat airborne contamination hazards using electrophoretic technology. With appropriate equipment, airborne particulates can be effectively removed and collected for disposal in one simple process. The equipment needed to implement electrophoresis is relatively inexpensive, highly reliable, and very compact. Once airborne contamination levels are reduced, less PPE is required and a significant cost savings may be realized through decreased waste and maximized productivity. Preliminary ''cold,'' or non-radioactive, testing results at the RFP have shown the technology to be effective on a reasonable scale, with several potential benefits and an abundance of applications

EpiContactTrace: an R-package for contact tracing during livestock disease outbreaks and for risk-based surveillance.

Science.gov (United States)

Nöremark, Maria; Widgren, Stefan

2014-03-17

During outbreak of livestock diseases, contact tracing can be an important part of disease control. Animal movements can also be of relevance for risk-based surveillance and sampling, i.e. both when assessing consequences of introduction or likelihood of introduction. In many countries, animal movement data are collected with one of the major objectives to enable contact tracing. However, often an analytical step is needed to retrieve appropriate information for contact tracing or surveillance. In this study, an open source tool was developed to structure livestock movement data to facilitate contact-tracing in real time during disease outbreaks and for input in risk-based surveillance and sampling. The tool, EpiContactTrace, was written in the R-language and uses the network parameters in-degree, out-degree, ingoing contact chain and outgoing contact chain (also called infection chain), which are relevant for forward and backward tracing respectively. The time-frames for backward and forward tracing can be specified independently and search can be done on one farm at a time or for all farms within the dataset. Different outputs are available; datasets with network measures, contacts visualised in a map and automatically generated reports for each farm either in HTML or PDF-format intended for the end-users, i.e. the veterinary authorities, regional disease control officers and field-veterinarians. EpiContactTrace is available as an R-package at the R-project website (http://cran.r-project.org/web/packages/EpiContactTrace/). We believe this tool can help in disease control since it rapidly can structure essential contact information from large datasets. The reproducible reports make this tool robust and independent of manual compilation of data. The open source makes it accessible and easily adaptable for different needs.

Characterisation of contamination migration in the workplace

International Nuclear Information System (INIS)

Boulaud, D.; Laborde, J.C.; Pourprix, M.

1994-01-01

The Institute for Nuclear Safety and Protection (IPSN) has developed a procedure for characterising airborne contamination between processes and the workplace in nuclear facilities. It was initially intended to use this process to validate operator choices concerning the monitoring of indoor air contamination (personnel monitoring, and environmental detection at fixed locations), but also to optimise the fundamental parameters which have a more or less direct influence on potential exposure of staff in the workplace (at the same time optimising the contamination source, close confinement, process ventilation and general ventilation). In practice, the methods used to obtain these expert appraisals were usually based on experiments carried out in situ: (i) characterisation of aerosol contamination by accurate measurement of the nature, concentration and particle size distribution at various locations; (ii) characterisation of the migration of contamination by precise measurement involving gas and/or particle tracing techniques. In parallel with these experiments, a considerable effort was made to develop and qualify computer codes capable of predicting or estimating the migration of contamination through complex ventilated areas, by means of both fluid mechanics and aerosol science. (Author)

Hospital-acquired Legionella infections: an update on the procedures for controlling environmental contamination.

Science.gov (United States)

Borella, P; Bargellini, A; Marchegiano, P; Vecchi, E; Marchesi, I

2016-01-01

The waterborne healthcare-associated infections are mainly sustained by Legionella and Pseudomonas spp. Various water factors and plumbing characteristics, and the interaction with other water microorganisms are considered to be predictive of Legionella contamination. It is therefore mandatory to organize plans of surveillance, prevention and control in order to avoid disease appearance in immunosuppressed patients, with higher risk of death. Guidelines for the prevention of Legionnaires' disease have been published, benefiting those who face this problem, but definitive standardized solutions do not exist yet. Here we describe fifteen years of activity, during which our study group gathered interesting data on the control of Legionella contamination. Water disinfection is not generally sufficient to control the risk of infection, but a complex water safety plan should be developed, including system maintenance, training of staff and implementation of a clinical surveillance system aimed at early detection of cases. Concerning the control measures, we evaluated the effectiveness of different treatments suggested to reduce Legionella spp contamination, comparing our results with the current literature data. The performance ranking was highest for the filter, followed by boilers at high temperature, monochloramine and, at a lower level, chlorine dioxide; the effectiveness of hyperchlorination was limited, and thermal shock was even more ineffective.

Contamination from an affluent of Furnas reservoir by trace metals

Directory of Open Access Journals (Sweden)

PP Cavalcanti

Full Text Available This study aims to determine concentrations and characterize trace metals distribution in an affluent of Furnas reservoir, Alfenas-MG. Water and sediment samples were taken monthly, 2010/10-2011/07 in five sites of Córrego do Pântano for subsequent determination of Pb, Cd and Zn levels by chemical analysis. The stream studied is in disagreement with Brazilian legislation for Class II water bodies (CONAMA 357. The highlights are the unsuitable concentrations of Pb for human consumption, according to Ministry of Health 2914 decree, providing risk for population.

Elemental composition of platelets. Part I. Sampling and sample preparation of platelets for trace-element analysis

International Nuclear Information System (INIS)

Iyengar, G.V.; Borberg, H.; Kasperek, K.; Kiem, J.; Siegers, M.; Feinendegen, L.E.; Gross, R.

1979-01-01

Sampling of platelets for trace-element analysis poses special problems: obtaining adequate sample materials, achieving a sufficient cell purity, preserving viability (integrity), correcting for trapped plasma, and controlling contamination. We used a blood-cell separator for the primary isolation of platelets from blood, and differential centrifugation in natural plasma to further isolate them. The pyrimidopyrimidine RA233 was used as a stabilizer to maintain viability. 131 I-labeled human serum albumin was used to estimate trapped plasma. Contamination was controlled by using five-times-distilled water to simulate donor's blood in the system and by comparing three fractions: the serum, the first portion of the platelet-rich plasma, and the supernatant plasma after the final centrifugation. Neutron activation analysis was used for the elemental analysis. A single differential centrifugation of the platelet-rich plasma from the blood-cell separator at 400 x g for 8 min was optimum (mean mass fractions: erythrocytes/platelets < 5 mg/g and leukocytes/platelets < 20 mg/g). The trapped plasma in the wet platelet samples amounted to about 0.40 g/g. No appreciable contamination from the sampling system was found for the elements Ag, Cd, Co, Cr, Cs, Cu, Fe, Mo, Rb, Sb, Se, and Zn. 2 figures, 3 tables

Tracing crustal contamination along the Java segment of the Sunda Arc, Indonesia

Science.gov (United States)

Jolis, E. M.; Troll, V.; Deegan, F.; Blythe, L.; Harris, C.; Freda, C.; Hilton, D.; Chadwick, J.; Van Helden, M.

2012-04-01

Arc magmas typically display chemical and petrographic characteristics indicative of crustal input. Crustal contamination can take place either in the mantle source region or as magma traverses the upper crust (e.g. [1]). While source contamination is generally considered the dominant process (e.g. [2]), late-stage crustal contamination has been recognised at volcanic arcs too (e.g. [3]). In light of this, we aim to test the extent of upper crustal versus source contamination along the Java segment of the Sunda arc, which, due its variable upper crustal structure, is an exemplary natural laboratory. We present a detailed geochemical study of 7 volcanoes along a traverse from Anak-Krakatau in the Sunda strait through Java and Bali, to characterise the impact of the overlying crust on arc magma composition. Using rock and mineral elemental geochemistry, radiogenic (Sr, Nd and Pb) and, stable (O) isotopes, we show a correlation between upper crustal composition and the degree of upper crustal contamination. We find an increase in 87Sr/86Sr and δ18O values, and a decrease in 143Nd/144Nd values from Krakatau towards Merapi, indicating substantial crustal input from the thick continental basement present. Volcanoes to the east of Merapi and the Progo-Muria fault transition zone, where the upper crust is thinner, in turn, show considerably less crustal input in their isotopic signatures, indicating a stronger influence of the mantle source. Our new data represent a systematic and high-resolution arc-wide sampling effort that allows us to distinguish the effects of the upper crust on the compositional spectrum of individual volcanic systems along the Sunda arc. [1] Davidson, J.P, Hora, J.M, Garrison, J.M & Dungan, M.A 2005. Crustal Forensics in Arc Magmas. J. Geotherm. Res. 140, 157-170; [2] Debaille, V., Doucelance, R., Weis, D., & Schiano, P. 2005. Geochim. Cosmochim. Acta, 70,723-741; [3] Gasparon, M., Hilton, D.R., & Varne, R. 1994. Earth Planet. Sci. Lett., 126, 15-22.

Occupational radioactive contamination of cement handlers of the civil construction

International Nuclear Information System (INIS)

Santos, Pedro Lopes dos; Gouvea, Rita de Cassia dos Santos; Kelecom, Alphonse; Dutra, Iedo Ramos

1999-01-01

Due to their occupational activities, several classes of workers are exposed to radioactive contamination by materials they handle and that contain traces of uranium and its descendants. This is the case of people that work in the civil construction and that currently handle Portland cement. Among other radioactive elements, cement contains the highly radiotoxic polonium-210 which may promote skin cancer because of its high specific activity and high LET α-particle it emits. Concentrations of polonium-210 are reported for urine, hair and skin smear of workers of the civil construction that usually handle cement. The results are compared to a control group. (author)

Long-term effects of aided phytostabilisation of trace elements on microbial biomass and activity, enzyme activities, and composition of microbial community in the Jales contaminated mine spoils

Energy Technology Data Exchange (ETDEWEB)

Renella, Giancarlo [Department of Soil Science and Plant Nutrition, University of Florence, Piazzale delle Cascine 28, I-50144 Florence (Italy)], E-mail: giancarlo.renella@unifi.it; Landi, Loretta; Ascher, Judith; Ceccherini, Maria Teresa; Pietramellara, Giacomo; Mench, Michel; Nannipieri, Paolo [Department of Soil Science and Plant Nutrition, University of Florence, Piazzale delle Cascine 28, I-50144 Florence (Italy)

2008-04-15

We studied the effectiveness of remediation on microbial endpoints, namely microbial biomass and activity, microbial and plant species richness, of an As-contaminated mine spoil, amended with compost (C) alone and in combination with beringite (B) or zerovalent iron grit (Z), to increase organic matter content and reduce trace elements mobility, and to allow Holcus lanatus and Pinus pinaster growth. Untreated spoil showed the lowest microbial biomass and activity and hydrolase activities, and H. lanatus as sole plant species, whereas the presented aided phytostabilisation option, especially CBZ treatment, significantly increased microbial biomass and activity and allowed colonisation by several plant species, comparable to those of an uncontaminated sandy soil. Microbial species richness was only increased in spoils amended with C alone. No clear correlation occurred between trace element mobility and microbial parameters and plant species richness. Our results indicate that the choice of indicators of soil remediation practices is a bottleneck. - Organo-mineral amendment and revegetation of a gold mine spoil increased microbial activity but did not increase microbial species richness.

Long-term effects of aided phytostabilisation of trace elements on microbial biomass and activity, enzyme activities, and composition of microbial community in the Jales contaminated mine spoils

International Nuclear Information System (INIS)

Renella, Giancarlo; Landi, Loretta; Ascher, Judith; Ceccherini, Maria Teresa; Pietramellara, Giacomo; Mench, Michel; Nannipieri, Paolo

2008-01-01

We studied the effectiveness of remediation on microbial endpoints, namely microbial biomass and activity, microbial and plant species richness, of an As-contaminated mine spoil, amended with compost (C) alone and in combination with beringite (B) or zerovalent iron grit (Z), to increase organic matter content and reduce trace elements mobility, and to allow Holcus lanatus and Pinus pinaster growth. Untreated spoil showed the lowest microbial biomass and activity and hydrolase activities, and H. lanatus as sole plant species, whereas the presented aided phytostabilisation option, especially CBZ treatment, significantly increased microbial biomass and activity and allowed colonisation by several plant species, comparable to those of an uncontaminated sandy soil. Microbial species richness was only increased in spoils amended with C alone. No clear correlation occurred between trace element mobility and microbial parameters and plant species richness. Our results indicate that the choice of indicators of soil remediation practices is a bottleneck. - Organo-mineral amendment and revegetation of a gold mine spoil increased microbial activity but did not increase microbial species richness

Barriers to Trace-back in a Salad-associated EHEC Outbreak, Sweden, June 2013.

Science.gov (United States)

Edelstein, Michael; Sundborger, Camilla; Hergens, Maria-Pia; Ivarsson, Sofie; Dryselius, Rikard; Insulander, Mona; Jernberg, Cecilia; Hutin, Yvan; Wallensten, Anders

2014-06-06

In June-July 2013, six counties notified the Swedish Institute for Communicable Disease Control of enterohaemorrhagic E.coli (EHEC) infections among attendees at a hotel in Dalarna, Sweden. An outbreak control team investigated to identify the source and implement control measures. We included individuals who attended the hotel between June 19th-25th in a cohort. We asked them about animal contact, swimming, and consumption of food items during this time using a questionnaire. A confirmed case was an EHEC O157:H7 outbreak strain positive individual who developed abdominal pain or diarrhoea between June 20th-July 2nd. We described the outbreak in time, place and person, calculated risk ratios (RR) and 95% confidence intervals (CI). We investigated the kitchen, tested and traced back implicated food items. 172 individuals responded. We identified 19 confirmed cases (Median age: 17 years, 64% female) with symptom onset between June 22nd-27th. Eating green salad on June 20th was associated with illness (RR:3.7;CI:1.3-11). The kitchen mixed green salads without records and destroyed leftovers immediately. Hence we could not conduct trace-back or obtain microbiological confirmation. Green salad contaminated before entering the kitchen was the likely outbreak source. We recommended early collaboration with food agencies and better restaurant records to facilitate future investigations.

Statistical analysis of trace metals in the plasma of cancer patients versus controls

International Nuclear Information System (INIS)

Pasha, Qaisara; Malik, Salman A.; Shah, Munir H.

2008-01-01

The plasma of cancer patients (n = 112) and controls (n = 118) were analysed for selected trace metals (Al, Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Mo, Na, Ni, Pb, Sb, Sr and Zn) by flame atomic absorption spectroscopy. In the plasma of cancer patients, mean concentrations of macronutrients/essential metals, Na, K, Ca, Mg, Fe and Zn were 3971, 178, 44.1, 7.59, 4.38 and 3.90 ppm, respectively, while the mean metal levels in the plasma of controls were 3844, 151, 74.2, 18.0, 6.60 and 2.50 ppm, respectively. Average concentrations of Cd, Cr, Cu, Mn, Mo, Ni, Pb, Sb, Sr and Zn were noted to be significantly higher in the plasma of cancer patients compared with controls. Very strong mutual correlations (r > 0.70) in the plasma of cancer patients were observed between Fe-Mn, Ca-Mn, Ca-Ni, Ca-Co, Cd-Pb, Co-Ni, Mn-Ni, Mn-Zn, Cr-Li, Ca-Zn and Fe-Ni, whereas, Ca-Mn, Ca-Mg, Fe-Zn, Ca-Zn, Mg-Mn, Mg-Zn, Cd-Sb, Cd-Co, Cd-Zn, Co-Sb and Sb-Zn exhibited strong relationships (r > 0.50) in the plasma of controls, all were significant at p < 0.01. Principal component analysis (PCA) of the data extracted five PCs, both for cancer patients and controls, but with considerably different loadings. The average metals levels in male and female donors of the two groups were also evaluated and in addition, the general role of trace metals in the carcinogenesis was discussed. The study indicated appreciably different pattern of metal distribution and mutual relationships in the plasma of cancer patients in comparison with controls

Statistical analysis of trace metals in the plasma of cancer patients versus controls

Energy Technology Data Exchange (ETDEWEB)

Pasha, Qaisara; Malik, Salman A. [Department of Biochemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Shah, Munir H. [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan)], E-mail: munir_qau@yahoo.com

2008-05-30

The plasma of cancer patients (n = 112) and controls (n = 118) were analysed for selected trace metals (Al, Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Mo, Na, Ni, Pb, Sb, Sr and Zn) by flame atomic absorption spectroscopy. In the plasma of cancer patients, mean concentrations of macronutrients/essential metals, Na, K, Ca, Mg, Fe and Zn were 3971, 178, 44.1, 7.59, 4.38 and 3.90 ppm, respectively, while the mean metal levels in the plasma of controls were 3844, 151, 74.2, 18.0, 6.60 and 2.50 ppm, respectively. Average concentrations of Cd, Cr, Cu, Mn, Mo, Ni, Pb, Sb, Sr and Zn were noted to be significantly higher in the plasma of cancer patients compared with controls. Very strong mutual correlations (r > 0.70) in the plasma of cancer patients were observed between Fe-Mn, Ca-Mn, Ca-Ni, Ca-Co, Cd-Pb, Co-Ni, Mn-Ni, Mn-Zn, Cr-Li, Ca-Zn and Fe-Ni, whereas, Ca-Mn, Ca-Mg, Fe-Zn, Ca-Zn, Mg-Mn, Mg-Zn, Cd-Sb, Cd-Co, Cd-Zn, Co-Sb and Sb-Zn exhibited strong relationships (r > 0.50) in the plasma of controls, all were significant at p < 0.01. Principal component analysis (PCA) of the data extracted five PCs, both for cancer patients and controls, but with considerably different loadings. The average metals levels in male and female donors of the two groups were also evaluated and in addition, the general role of trace metals in the carcinogenesis was discussed. The study indicated appreciably different pattern of metal distribution and mutual relationships in the plasma of cancer patients in comparison with controls.

Determination of trace element contents in grass samples for cattle feeding using NAA techniques

Energy Technology Data Exchange (ETDEWEB)

Yusof, Alias Mohamad; Jagir Singh, Jasbir Kaur

1987-09-01

An investigation on trace elements contents in six types of grass samples used for cattle feeding have been carried out using NAA techniques. The grass samples, Mardi Digit, African Star, Signal, Guinea, Setaria and Setaria Splendida were found to contain at least 19 trace elements in varying concentrations. The results were compared to the figures obtained from available sources to ascertain the status as to whether the grass samples studied would satisfy the minimum requirements of trace elements present in grass for cattle feeding or otherwise. Preference made on the suitability of the grass samples for cattle feeding was based on the availability and abundance of the trace elements, taking into account factors such as the degree of toxicity, inadequate amounts and contamination due to the presence of other trace elements not essential for cattle feeding.

Determination of trace element contents in grass samples for cattle feeding using NAA techniques

International Nuclear Information System (INIS)

Alias Mohamad Yusof; Jasbir Kaur Jagir Singh

1987-01-01

An investigation on trace elements contents in six types of grass samples used for cattle feeding have been carried out using NAA techniques. The grass samples, Mardi Digit, African Star, Signal, Guinea, Setaria and Setaria Splendida were found to contain at least 19 trace elements in varying concentrations. The results were compared to the figures obtained from available sources to ascertain the status as to whether the grass samples studied would satisfy the minimum requirements of trace elements present in grass for cattle feeding or otherwise. Preference made on the suitability of the grass samples for cattle feeding was based on the availability and abundance of the trace elements, taking into account factors such as the degree of toxicity, inadequate amounts and contamination due to the presence of other trace elements not essential for cattle feeding. (author)

Trace elements in nail polish as a source of contamination of nail clippings when used in epidemiological studies

International Nuclear Information System (INIS)

Favaro, P.C.; Bode, P.; De Nadai Fernandes, E.A.

2005-01-01

Trace elements were determined in 27 brands of nail polish using INAA so as to estimate the impact of nail polish remainders when using (finger, toe) nail clippings as a bioindicator for epidemiological studies. Fe was found to be present up to almost 1.7% in one brand. No unambiguous correlation between trace elements and color was established, though transparent polish has the lowest trace element concentrations. An estimate of the maximum effect (no removal of the paint) indicates that over-estimates of some trace element levels in nail with more than 200.000% may occur. If nail clippings will be used to study trace elements, very high demands have to be set to the efficiency and selectivity of the cleaning procedure. (author)

Environmental viral contamination in a pediatric hospital outpatient waiting area: implications for infection control.

Science.gov (United States)

D'Arcy, Nikki; Cloutman-Green, Elaine; Klein, Nigel; Spratt, David A

2014-08-01

Nosocomial outbreaks of viral etiology are costly and can have a major impact on patient care. Many viruses are known to persist in the inanimate environment and may pose a risk to patients and health care workers. We investigate the frequency of environmental contamination with common health care-associated viruses and explore the use of torque-teno virus as a marker of environmental contamination. Environmental screening for a variety of clinically relevant viruses was carried out over 3 months in a UK pediatric hospital using air sampling and surface swabbing. Swabs were tested for the presence of virus nucleic acid by quantitative polymerase chain reactions. Viral nucleic acid was found on surfaces and in the air throughout the screening period, with adenovirus DNA being the most frequent. Door handles were frequently contaminated. Torque-teno virus was also found at numerous sites. Evidence of environmental contamination with viral pathogens is present in health care environments and may be indicative of an infectious virus being present. Screening for viruses should be included in infection control strategies. Torque-teno virus may provide a better marker of contamination and reduce time and cost of screening for individual viruses. Copyright © 2014 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Mosby, Inc. All rights reserved.

White popular (Populus alba L.) - Litter impact on chemical and biochemical parameters related to nitrogen cycle in contaminated soils

Energy Technology Data Exchange (ETDEWEB)

Ciadamidaro, L.; Madejon, P.; Cabrera, F.; Madejon, E.

2014-06-01

Aim of study: The aim of this study was to determine the effect of litter from Populus alba on chemical and biochemical properties related to the N cycle in soils with different pH values and trace element contents. We hypothesized that this litter would influence several parameters related to the N cycle and consequently to soil health. Area of study: we collected two reforested contaminated soils of different pH values (AZ pH 7.23 and DO pH 2.66) and a non-contaminated soil (RHU pH 7.19). Materials and methods: Soil samples were placed in 2,000 cm{sup 3} microcosms and were incubated for 40 weeks in controlled conditions. Each soil was mixed with its corresponding litter, and soils without litter were also tested for comparison. Ammonium (NH{sub 4}{sup 4}+-N) and nitrate (NO{sub 3}{sup -} -N) content, potential nitrification rate (PNR), microbial biomass nitrogen (MBN), protease activity, and several chemical properties such as pH, available trace element concentrations (extracted with 0.01 M CaCl{sub 2}) were determined at different times of incubation. Main results: Values of available trace elements did not vary during the incubation and were always higher in acid soil. In neutral soils litter presence increased values of Kjeldahl-N, NO{sub 3} –-N content, potential nitrification rate (PNR), microbial biomass nitrogen (MBN) and protease activity. Presence of trace elements in neutral soils did not alter the parameters studied. However, acidic pH and high content of available trace elements strongly affected NH{sub 4}{sup +}-N and NO{sub 3}{sup -} -N, microbial biomass N and protease activity. Research highlights: Our results showed the negative effect of the acidity and trace element availability in parameters related with the N-cycle. (Author)

White poplar (Populus alba L. - Litter impact on chemical and biochemical parameters related to nitrogen cycle in contaminated soils

Directory of Open Access Journals (Sweden)

Paula Madejon

2014-04-01

Full Text Available Aim of study: The aim of this study was to determine the effect of litter from Populus alba on chemical and biochemical properties related to the N cycle in soils with different pH values and trace element contents. We hypothesized that this litter would influence several parameters related to the N cycle and consequently to soil health.Area of study: we collected two reforested contaminated soils of different pH values (AZ pH 7.23 and DO pH = 2.66 and a non-contaminated soil (RHU pH 7.19.Materials and methods: Soil samples were placed in 2,000 cm3 microcosms and were incubated for 40 weeks in controlled conditions. Each soil was mixed with its corresponding litter, and soils without litter were also tested for comparison. Ammonium (NH4+-N and nitrate (NO3–-N content, potential nitrification rate (PNR, microbial biomass nitrogen (MBN, protease activity, and several chemical properties such as pH, available trace element concentrations (extracted with 0.01 M CaCl2 were determined at different times of incubation.Main results: Values of available trace elements did not vary during the incubation and were always higher in acid soil. In neutral soils litter presence increased values of Kjeldahl-N, NO3–-N content, potential nitrification rate (PNR, microbial biomass nitrogen (MBN and protease activity. Presence of trace elements in neutral soils did not alter the parameters studied. However, acidic pH and high content of available trace elements strongly affected NH4+-N andNO3–-N, microbial biomass N and protease activity.Research highlights: Our results showed the negative effect of the acidity and trace element availability in parameters related with the N-cycle.Key words: microbial biomass N; protease activity; soil pH; N mineralization; nitrification; phytoremediation.

Extended reactivity trace curves for nuclear power control with no power shooting

Energy Technology Data Exchange (ETDEWEB)

Ratemi, W M; Elbuni, M S [Faculty of engineering, Al Fateh universty Tripoli (Libyan Arab Jamahiriya)

1995-10-01

This paper introduces a new concept of reactivity trace curve (RTC) for nuclear power control with no power shooting. The concept is based on recent work of bernard et al. on the dynamic period of nuclear reactors. RTC-method is simulated for both a static effective decay constant corresponding to a one-group delayed neutrons model, and a dynamic effective decay constant corresponding to a six-group delayed neutrons model. A fitting to the RTC of a six-group reactor model resulted in a closed from formula for the RTC that couples the effect of both static and dynamic decay constants. Hence, introducing two `fingerprints` for the reactor in concern to identify a closed from RTC formula capable of controlling the reactor power. Integration of the RTC with control rod integral curves results in the {rho}-z-t diagram. This diagram relates the amount of recommended reactivity (RTC), the position of control rod, and the time required for power control. 8 figs.

Extended reactivity trace curves for nuclear power control with no power shooting

International Nuclear Information System (INIS)

Ratemi, W. M.; Elbuni, M. S.

1995-01-01

This paper introduces a new concept of reactivity trace curve (RTC) for nuclear power control with no power shooting. The concept is based on recent work of bernard et al. on the dynamic period of nuclear reactors. RTC-method is simulated for both a static effective decay constant corresponding to a one-group delayed neutrons model, and a dynamic effective decay constant corresponding to a six-group delayed neutrons model. A fitting to the RTC of a six-group reactor model resulted in a closed from formula for the RTC that couples the effect of both static and dynamic decay constants. Hence, introducing two 'fingerprints' for the reactor in concern to identify a closed from RTC formula capable of controlling the reactor power. Integration of the RTC with control rod integral curves results in the ρ-z-t diagram. This diagram relates the amount of recommended reactivity (RTC), the position of control rod, and the time required for power control. 8 figs

Certification for Trace Elements and Methyl Mercury Mass Fractions in IAEA-452 Scallop (Pecten maximus) Sample

International Nuclear Information System (INIS)

2013-01-01

The primary goal of the IAEA Environment Laboratories (NAEL) is to help Member States understand, monitor and protect the marine environment. The major impact exerted by large coastal cities on marine ecosystems is therefore of great concern to the IAEA, particularly to its Environment Laboratories. The marine pollution assessments needed to understand such impacts depend on accurate knowledge of contaminant concentrations in various environmental compartments. Two fundamental requirements to ensure the reliability of analytical results are quality control (QC) and quality assurance (QA). Since the early 1970s, NAEL has been assisting national laboratories and regional laboratory networks through its reference material programme for the analysis of radionuclides, trace elements and organic compounds in marine samples. Relevant activities include global interlaboratory comparison exercises and regional proficiency tests, the production of marine reference materials, and the development of reference methods for analysis of trace elements and organic pollutants in marine samples. QA, QC and associated good laboratory practice should be essential components of all marine environmental monitoring. QC procedures are commonly based on the analysis of reference materials to assess reproducibility and measurement bias. QA can be realized by participation in externally organized laboratory performance studies, also known as interlaboratory comparison exercises, which compare and evaluate the analytical performance and measurement capabilities of participating laboratories. The need for good QA/QC in the chemical analysis of marine environmental samples is widely recognized and has been tested in a number of international QA exercises. Such diligence also needs to be applied to other components of the monitoring exercise, since these may represent a greater source of error in many instances. Data that are not based on adequate QA/QC can be erroneous, and their misuse can lead

Effect evaluation of carbendazim-β-ciclodextrin complex for controling filamentous contaminants of plant in vitro cultura

Directory of Open Access Journals (Sweden)

Mileidy Cruz-Martín

2002-04-01

Full Text Available The majority of in vitro contaminant microorganisms affecting plant in vitro culture are bacterias and fungus. These are commonly observed in vivo on plants, but they could cause harmful effect on plant propagated in vitro. The search of new alternatives for their prevention and control is a priority. Carbendazim is the active ingredient of some systemic fungicides, it´s application for fungus contamination on in vitro propagation of plant it has been constrained for their lowsolubilityonwater.Thisproblemcouldbesolvedbycombiningthisproductwitha β-ciclodextrina.Thispaperwas focusedtodeterminetheeffectofcarbendazim-β-ciclodextrinaversusthecontaminantfungiofplantinvitroculture. It was determined the Minimum Inhibitory Concentration (MIC by the agar dilution method. Thirty four strains were analysed.Thecarbendazim-β-ciclodextrinacomplexshowedanacceptableantifungalactivityversuscontaminant. This result could be an useful alternative to control the fungi contamination on plant propagated in vitro. Key words: fungal contamination, antifungal compounds, minimum inhibitory concentration

Trace metal concentrations in marine zooplankton from the western Bay of Bengal

Digital Repository Service at National Institute of Oceanography (India)

Rejomon, G.; Balachandran, K.K.; Nair, M.; Joseph, T.

on the interrelationships of zooplankton and phytoplankton. – Journal of Marine Biological Association U.K 32: 375-445. [2] Brooks, R.R., Presley, B.J., Kaplan, I.R. (1967): APDC-MIBK extraction system for the determination of trace elements in saline waters by Atomic... of contaminants in the food web dynamics as well as in the biogeochemical cycling of trace elements. Zooplanktons are the most abundant animals in the sea, which play an important role in the marine food chain. They mostly feed on phytoplankton and in turn...

Trace metal contaminants in sediments and soils: comparison between ICP and XRF quantitative determination

Directory of Open Access Journals (Sweden)

Congiu A.

2013-04-01

Full Text Available A mineralization method HCl-free for heavy metals analysis in sediments and soils by DRC-ICP-MS was developed. The procedure, which uses concentrated nitric, hydrofluoric acid and hydrogen peroxide, was applied for the analysis of arsenic, cadmium, chromium, nickel and vanadium. The same samples were then analyzed, as pressed pellets, by wavelength dispersive X ray fluorescence (WD-XRF using the dedicated PANalytical Pro Trace solution for the determination of trace elements. Comparison of ICP and XRF data showed good agreement for the elements under investigation, unless for chromium in soils, which recovery was not complete.

Explosive Contamination from Substrate Surfaces: Differences and Similarities in Contamination Techniques Using RDX and C-4

Science.gov (United States)

Miller, C. J.; Yoder, T. S.

2010-06-01

Explosive trace detection equipment has been deployed to airports for more than a decade. During this time, the need for standardized procedures and calibrated trace amounts for ensuring that the systems are operating properly and detecting the correct explosive has been apparent but a standard representative of a fingerprint has been elusive. Standards are also necessary to evaluate instrumentation in the laboratories during development and prior to deployment to determine sample throughput, probability of detection, false positive/negative rates, ease of use by operator, mechanical and/or software problems that may be encountered, and other pertinent parameters that would result in the equipment being unusable during field operations. Since many laboratories do not have access to nor are allowed to handle explosives, the equipment is tested using techniques aimed at simulating the actual explosives fingerprint. This laboratory study focused on examining the similarities and differences in three different surface contamination techniques that are used to performance test explosive trace detection equipment in an attempt to determine how effective the techniques are at replicating actual field samples and to offer scenarios where each contamination technique is applicable. The three techniques used were dry transfer deposition of standard solutions using the Transportation Security Laboratory’s (TSL) patented dry transfer techniques (US patent 6470730), direct deposition of explosive standards onto substrates, and fingerprinting of actual explosives onto substrates. RDX was deposited on the surface of one of five substrates using one of the three different deposition techniques. The process was repeated for each substrate type using each contamination technique. The substrate types used were: 50% cotton/50% polyester as found in T-shirts, 100% cotton with a smooth surface such as that found in a cotton dress shirt, 100% cotton on a rough surface such as that

Testing of portal monitors for personnel contamination control

International Nuclear Information System (INIS)

Johnson, L.O.; Gupta, V.P.; Stevenson, R.L.; Stalker, A.C.; Baker, K.R.; Littleton, M.L.; Rich, B.L.

1983-04-01

This is a report of an INPO-funded evaluation of state-of-the-art portal monitors used to detect personnel contamination. The project developed techniques and procedures to evaluate the performance and sensitivity of the portal monitors which provided data for intercomparison. An additional accomplishment was development of a methodology to assist manufacturers and users to optimize the monitor settings, and to provide technical basis for the eventual use of fixed monitors to replace frisking for contamination control. The monitors tested utilize thin-window gas-flow proportional counters sensitive to beta and gamma radiation. Various tests were performed: (1) background count rate and the statistical variability, (2) detector efficiency at different distances, (3) moving source sensitivity for various size sources and speeds, and (4) false alarm rates at different background levels. A model has been developed for the moving source measurements to compare the experimental data, and to test whether it is possible to adequately model the behavior of a portal monitor response to a moving source. The model results with the actual test results are compared

Contaminants from Cretaceous Black Shale Part 1: Natural weathering processes controlling contaminant cycling in Mancos Shale, southwestern United States, with emphasis on salinity and selenium

Science.gov (United States)

Tuttle, Michele L.W.; Fahy, Juli W.; Elliott, John G.; Grauch, Richard I.; Stillings, Lisa L.

2013-01-01

Colorado River well into the future. Other trace elements weathering from MS that are often of environmental concern include U and Mo, which mimic Se in their behavior; As, Co, Cr, Cu, Ni, and Pb, which show little redistribution; and Cd, Sb, V, and Zn, which accumulate in Stage I shale, but are lost to varying degrees from upper soil intervals. None of these trace elements have been reported previously as contaminants in the study area.

The development and assessment of TRACE/PARCS model for Lungmen ABWR

Energy Technology Data Exchange (ETDEWEB)

Lin, Hao-Tzu, E-mail: htlin@iner.gov.tw [Institute of Nuclear Energy Research, Atomic Energy Council, R.O.C., 1000, Wenhua Road, Jiaan Village, Longtan Township, Taoyuan County, 32546, Taiwan, ROC (China); Wang, Jong-Rong, E-mail: jrwang@iner.gov.tw [Institute of Nuclear Energy Research, Atomic Energy Council, R.O.C., 1000, Wenhua Road, Jiaan Village, Longtan Township, Taoyuan County, 32546, Taiwan, ROC (China); Chen, Hsiung-Chih, E-mail: km8385@gmail.com [Institute of Nuclear Engineering and Science, National Tsing Hua University, No. 101, Section 2, Kuang Fu Road, HsinChu 30013, Taiwan, ROC (China); Shih, Chunkuan, E-mail: ckshih@ess.nthu.edu.tw [Institute of Nuclear Engineering and Science, National Tsing Hua University, No. 101, Section 2, Kuang Fu Road, HsinChu 30013, Taiwan, ROC (China)

2014-07-01

Highlights: • The development of a TRACE/PARCS model of Lungmen (ABWR). • Thermal-hydraulics model of TRACE is coupling with 3-D neutronics model of PARCS. • The 3-D geometry vessel component of TRACE is used in this study. • The parameters responses of Lungmen TRACE/PARCS model are consistent with FSAR data. - Abstract: This study consists of two steps. The first step is the development of a TRACE (TRAC/RELAP Advanced Computational Engine)/PARCS (Purdue Advanced Reactor Core Simulator) model of Lungmen nuclear power plant (NPP) which includes the vessel, reactor internal pumps (RIPs), main steam lines, and important control systems (such as the feedwater control system, steam bypass and pressure control system, and recirculation flow control system), etc. Key parameters were identified to refine the TRACE/PARCS model further in the frame of a steady state analysis. The second step is the performance of Lungmen NPP TRACE/PARCS model transient analyses. The transient data of Final Safety Analysis Report (FSAR) chapter 15th were used to compare with the results of Lungmen NPP TRACE/PARCS model. The trends of TRACE/PARCS analysis results were consistent with the FSAR data. It indicated that there was a respectable accuracy in the Lungmen NPP TRACE/PARCS model and it also depicted that the Lungmen NPP TRACE/PARCS model was satisfying for the purpose of Lungmen NPP safety analyses.

Contamination control by laundry monitor at NPP

International Nuclear Information System (INIS)

Singh, Vishwanath P.; Rana, P.K.; Lokeshwar Rao, S.; Managanvi, S.S.

2010-01-01

The operation of nuclear power reactor produces electricity as well as small quantity of radioactive waste as gaseous, liquid and solid. The waste contains radionuclides produced by fission and activation in reactor systems with wide spectrum of energy and half life. The long-lived nuclides Sr, Cs, Ba, Iodine and Co etc compared to short-lived are important in view of radiation protection. The radioactive contamination on the materials, human body or other places where it is undesirable is enormously harmful to workers at Nuclear Power Plant (NPP). The spread of radioactive from controlled areas is very complex problem for power reactor plant management

Evaluation de la contamination de la chaîne trophique par les éléments traces (Cu, Co, Zn, Pb, Cd, U, V et As dans le bassin de la Lufira supérieure (Katanga/RD Congo

Directory of Open Access Journals (Sweden)

Katemo Manda, B.

2010-01-01

Full Text Available Evaluation of Contamination of the Food Chain by Trace Elements (Cu, Co, Zn, Pb, Cd, U, V and As in the Basin of the Upper Lufira (Katanga/DR Congo. Seven trace elements (Cu, Co, Zn, Cd, Pb, U, V and As were analyzed using a HR ICP-MS in samples of water, plankton, leaves of Phragmites australis, muscle and gills of three fish species (Oreochromis macrochir, Tilapia rendalli, Clarias gariepinus collected in the basin of the upper Lufira. The results indicate a high copper (70.9 ppm and cobalt (32.3 ppm content in the effluent of complex hydrometallurgical Shituru. If contamination of rivers decreases with distance from the pollution source, the values are very high in lake Tshangalele for plankton and leaves of P. australis. For fish, the results indicate that Pb, U, V, Cu, Co and Cd accumulates preferentially in the gills but Zn accumulates more in the muscles. As accumulates in the same order of magnitude in both organs. These results confirm the pollution of the basin by the effluents from Lufira complex hydrometallurgical Shituru.

Phytoremediation trials on metal- and arsenic-contaminated pyrite wastes (Torviscosa, Italy).

Science.gov (United States)

Vamerali, Teofilo; Bandiera, Marianna; Coletto, Lucia; Zanetti, Federica; Dickinson, Nicholas M; Mosca, Giuliano

2009-03-01

At a site in Udine, Italy, a 0.7m layer of As, Co, Cu, Pb and Zn contaminated wastes derived from mineral roasting for sulphur extraction had been covered with an unpolluted 0.15m layer of gravelly soil. This study investigates whether woody biomass phytoremediation is a realistic management option. Comparing ploughing and subsoiling (0.35m depth), the growth of Populus and Salix and trace element uptake were investigated in both pot and field trials. Species differences were marginal and species selection was not critical. Impaired above-ground productivity and low translocation of trace elements showed that bioavailable contaminant stripping was not feasible. The most significant finding was of coarse and fine roots proliferation in surface layers that provided a significant sink for trace elements. We conclude that phytostabilisation and effective immobilisation of metals and As could be achieved at the site by soil amelioration combined with woody species establishment. Confidence to achieve a long-term and sustainable remediation requires a more complete quantification of root dynamics and a better understanding of rhizosphere processes.

Epidemic contact tracing via communication traces.

Directory of Open Access Journals (Sweden)

Katayoun Farrahi

Full Text Available Traditional contact tracing relies on knowledge of the interpersonal network of physical interactions, where contagious outbreaks propagate. However, due to privacy constraints and noisy data assimilation, this network is generally difficult to reconstruct accurately. Communication traces obtained by mobile phones are known to be good proxies for the physical interaction network, and they may provide a valuable tool for contact tracing. Motivated by this assumption, we propose a model for contact tracing, where an infection is spreading in the physical interpersonal network, which can never be fully recovered; and contact tracing is occurring in a communication network which acts as a proxy for the first. We apply this dual model to a dataset covering 72 students over a 9 month period, for which both the physical interactions as well as the mobile communication traces are known. Our results suggest that a wide range of contact tracing strategies may significantly reduce the final size of the epidemic, by mainly affecting its peak of incidence. However, we find that for low overlap between the face-to-face and communication interaction network, contact tracing is only efficient at the beginning of the outbreak, due to rapidly increasing costs as the epidemic evolves. Overall, contact tracing via mobile phone communication traces may be a viable option to arrest contagious outbreaks.

Epidemic contact tracing via communication traces.

Science.gov (United States)

Farrahi, Katayoun; Emonet, Rémi; Cebrian, Manuel

2014-01-01

Traditional contact tracing relies on knowledge of the interpersonal network of physical interactions, where contagious outbreaks propagate. However, due to privacy constraints and noisy data assimilation, this network is generally difficult to reconstruct accurately. Communication traces obtained by mobile phones are known to be good proxies for the physical interaction network, and they may provide a valuable tool for contact tracing. Motivated by this assumption, we propose a model for contact tracing, where an infection is spreading in the physical interpersonal network, which can never be fully recovered; and contact tracing is occurring in a communication network which acts as a proxy for the first. We apply this dual model to a dataset covering 72 students over a 9 month period, for which both the physical interactions as well as the mobile communication traces are known. Our results suggest that a wide range of contact tracing strategies may significantly reduce the final size of the epidemic, by mainly affecting its peak of incidence. However, we find that for low overlap between the face-to-face and communication interaction network, contact tracing is only efficient at the beginning of the outbreak, due to rapidly increasing costs as the epidemic evolves. Overall, contact tracing via mobile phone communication traces may be a viable option to arrest contagious outbreaks.

Control levels for residual contamination in materials considered for recycle and reuse

International Nuclear Information System (INIS)

Hill, R.L.; Aaberg, R.L.; Baker, D.A.; Kennedy, W.E. Jr.

1993-09-01

Pacific Northwest Laboratory (PNL) is collecting data and conducting technical analyses to support joint efforts by the U.S. Department of Energy (DOE), Office of Environmental Guidance, Air, Water and Radiation Division (DOE/EH-232); by the U.S. Environmental Protection Agency (EPA); and by the U.S. Nuclear Regulatory Commission (NRC) to develop radiological control criteria for the recycle and reuse of scrap materials and equipment that contain residual radioactive contamination. The initial radiological control levels are the concentrations in or on materials considered for recycle or reuse that meet the individual (human) or industrial (electronics/film) dose criteria. The analysis identifies relevant radionuclides, potential mechanisms of exposure, and methods to determine possible non-health-related impacts from residual radioactive contamination in materials considered for recycle or reuse. The generic methodology and scenarios described here provide a basic framework for numerically deriving radiological control criteria for recycle or reuse. These will be adequately conservative for most situations

Air contamination control as an element of state environmental monitoring

International Nuclear Information System (INIS)

Grabowski, D.

1993-01-01

The results of air contamination control on the base of gamma and beta radioactivity of aerosols collected on filters and in precipitation samples have been shown. The data have been gathered from 12 monitoring stations in Poland during 1993. No significant differences between actual results and those obtained in previous years have been noticed. 4 figs, 1 tab

Erosion and Soil Contamination Control Using Coconut Flakes And Plantation Of Centella Asiatica And Chrysopogon Zizanioides

Science.gov (United States)

Roslan, Rasyikin; Che Omar, Rohayu; Nor Zuliana Baharuddin, Intan; Zulkarnain, M. S.; Hanafiah, M. I. M.

2016-11-01

Land degradation in Malaysia due to water erosion and water logging cause of loss of organic matter, biodiversity and slope instability but also land are contaminated with heavy metals. Various alternative such as physical remediation are use but it not showing the sustainability in term of environmental sustainable. Due to that, erosion and soil contamination control using coconut flakes and plantation of Centella asiatica and Chrysopogon zizanioides are use as alternative approach for aid of sophisticated green technology known as phytoremediation and mycoremediation. Soil from cabonaceous phyllite located near to Equine Park, Sri Kembangan are use for monitoring the effect of phytoremediation and mycoremediation in reducing soil contamination and biotechnology for erosion control. Five laboratory scale prototypes were designed to monitor the effect of different proportion of coconut flakes i.e. 10%, 25%, 50% & 100% and plantation of Centella asiatica and Chrysopogon zizanioides to reduce the top soil from eroding and reduce the soil contamination. Prototype have been observe started from first week and ends after 12 weeks. Centella asiatica planted on 10% coconut flakes with 90% soil and Chrysopogon zizanioides planted on 25% coconut flakes with 75% soil are selected proportion to be used as phytoremediation and mycoremediation in reducing soil contamination and biotechnology for erosion control.

A watershed-scale approach to tracing metal contamination in the environment

Science.gov (United States)

Church, Stanley E

1996-01-01

IntroductionPublic policy during the 1800's encouraged mining in the western United States. Mining on Federal lands played an important role in the growing economy creating national wealth from our abundant and diverse mineral resource base. The common industrial practice from the early days of mining through about 1970 in the U.S. was for mine operators to dispose of the mine wastes and mill tailings in the nearest stream reach or lake. As a result of this contamination, many stream reaches below old mines, mills, and mining districts and some major rivers and lakes no longer support aquatic life. Riparian habitats within these affected watersheds have also been impacted. Often, the water from these affected stream reaches is generally not suitable for drinking, creating a public health hazard. The recent Department of Interior Abandoned Mine Lands (AML) Initiative is an effort on the part of the Federal Government to address the adverse environmental impact of these past mining practices on Federal lands. The AML Initiative has adopted a watershed approach to determine those sites that contribute the majority of the contaminants in the watershed. By remediating the largest sources of contamination within the watershed, the impact of metal contamination in the environment within the watershed as a whole is reduced rather than focusing largely on those sites for which principal responsible parties can be found.The scope of the problem of metal contamination in the environment from past mining practices in the coterminous U.S. is addressed in a recent report by Ferderer (1996). Using the USGS1:2,000,000-scale hydrologic drainage basin boundaries and the USGS Minerals Availability System (MAS) data base, he plotted the distribution of 48,000 past-producing metal mines on maps showing the boundaries of lands administered by the various Federal Land Management Agencies (FLMA). Census analysis of these data provided an initial screening tool for prioritization of

Metals in environmental media: A study of trace and platinum group ...

African Journals Online (AJOL)

A detailed study has been conducted to determine the contamination of Thohoyandou roadside soils, vegetation, sewage and river waters by Zn, Cu, Cr, Pb, Cd, Fe, Pt and Pd. The study further investigated the correlation between these trace metals in roadside soils and vegetation in order to infer the potential impacts of ...

trace metals in selected fish species from lakes awassa and ziway

African Journals Online (AJOL)

Preferred Customer

were collected from six sampling stations in Lakes Awassa and Ziway, Ethiopia. The edible ... Concentrations of trace elements in the fishes ranged (µg element/g dry mass): Zn. 23.04–30.92; Fe ...... water and soil sediments from some fishponds. Int. J. Environ. ... radioactive contaminants in the aquatic environ- ment and ...

Bio-Contamination Control for Spacesuit Garments - A Preliminary Study

Science.gov (United States)

Rhodes, Richard; Korona, Adam; Orndoff, Evelyn; Ott, Mark; Poritz, Darwin

2010-01-01

This paper outlines a preliminary study to review, test, and improve upon the current state of spacesuit bio-contamination control. The study includes an evaluation of current and advanced suit materials, ground and on-orbit cleaning methods, and microbial test and analysis methods. The first aspect of this study was to identify potential anti-microbial textiles and cleaning agents, and to review current microbial test methods. The anti-microbial cleaning agent and textile market survey included a review of current commercial-off-the-shelf (COTS) products that could potentially be used as future space flight hardware. This review included replacements for any of the softgood layers that may become contaminated during an extravehicular activity (EVA), including the pressure bladder, liquid cooling garment, and ancillary comfort undergarment. After a series of COTS anti-microbial textiles and clean ing agents were identified, a series of four tests were conducted: (1) a stacked configuration test that was conducted in order to review how bio-contamination would propagate through the various suit layers, (2) a individual materials test that evaluated how well each softgood layer either promoted or repressed growth, (3) a cleaning agent test that evaluated the efficacy on each of the baseline bladders, and (4) an evaluation of various COTS anti-microbial textiles. All antimicrobial COTS materials tested appeared to control bacteria colony forming unit (CFU) growth better than the Thermal Comfort Undergarment (TCU) and ACES Liquid Cooling Garment (LCG)/EMU Liquid Cooling Ventilation Garment (LCVG) materials currently in use. However, a comparison of fungi CFU growth in COTS to current suit materials appeared to vary per material. All cleaning agents tested in this study appeared to inhibit the level of bacteria and fungi growth to acceptable levels for short duration tests. While several trends can be obtained from the current analysis, a series of test improvements are

A General LC-MS/MS Method for Monitoring Potential β-Lactam Contamination in Drugs and Drug-Manufacturing Surfaces.

Science.gov (United States)

Qiu, Chen; Zhu, Hongbin; Ruzicka, Connie; Keire, David; Ye, Hongping

2018-05-15

Penicillins and some non-penicillin β-lactams may cause potentially life-threatening allergic reactions. Thus, possible cross contamination of β-lactams in food or drugs can put people at risk. Therefore, when there is a reasonable possibility that a non-penicillin product could be contaminated by penicillin, the drug products are tested for penicillin contamination. Here, a sensitive and rapid method for simultaneous determination of multiple β-lactam antibiotics using high performance liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed and validated. Mass spectral acquisition was performed on a Q-Exactive HF mass spectrometer in positive ion mode with parallel reaction monitoring (PRM). The method was validated for seven β-lactam antibiotics including one or two from each class and a synthetic intermediate. The quantification precision and accuracy at 200 ppb were in the range of ± 1.84 to ± 4.56 and - 5.20 to 3.44%, respectively. The limit of detection (LOD) was 0.2 ppb, and the limit of quantitation (LOQ) was 2 ppb with a linear dynamic range (LDR) of 2-2000 ppb for all eight β-lactams. From various drug products, the recoveries of eight β-lactams at 200 and 2 ppb ranged from 93.8 ± 3.2 to 112.1 ± 4.2% and 89.7 ± 4.6 to 110.6 ± 1.9%, respectively. The application of the method for detecting cross contamination of trace β-lactams (0.2 ppb) and for monitoring facility surface cleaning was also investigated. This sensitive and fast method was fit-for-purpose for detecting and quantifying trace amount of β-lactam contamination, monitoring cross contamination in manufacturing processes, and determining potency for regulatory purposes and for quality control.

Can "contamination" occur in body bags?-The example of background fibres in body bags used in Australia.