WorldWideScience

Sample records for trabecular metal cups

  1. Trabecular metal acetabular revision system (cup-cage construct to address the massive acetabular defects in revision arthroplasty

    Directory of Open Access Journals (Sweden)

    Rajesh Malhotra

    2012-01-01

    Full Text Available The increasing number of total hip replacements in the younger clique has added to the demand for revision procedures. Revision situations are often encountered with infection, loss of bone stock and bone defects. There are various methods of reconstruction of acetabular defects. The management options of type 3B Paprosky acetabular defects are limited with allograft and conventional cages. Trabecular metal technology has evolved to address these bone defects. Trabecular metal acetabular revision system (TMARS cup-cage construct is a new technique to address massive acetabular defects. We describe a case of failed hip reconstruction done for a Giant cell tumour of proximal femur managed by a two stage procedure, initial debridement and second stage reconstruction of acetabulum with TMARS cup-cage construct and femur with allograft prosthesis composite.

  2. Copas de metal trabecular y aloinjertos óseos impactados en defectos acetabulares graves. Resultados a los 2-4 años. [Impacted bone allografts and trabecular metal cups in severe acetabular bone defects: 2 to 4-year results.

    Directory of Open Access Journals (Sweden)

    Martín Buttaro

    2014-06-01

    Full Text Available In­tro­duc­ción: El objetivo principal es presentar la supervivencia del componente acetabular en pacientes con defectos graves reconstruidos con copas de metal trabecular combinadas con aloinjertos óseos impactados. Como objetivo secundario, se compararon estos resultados con los previamente obtenidos por los autores en defectos de similar gravedad utilizando anillos de reconstrucción y aloinjertos óseos. Materiales­ y­ Métodos:­ Se realizaron 20 cirugías de revisión en 19 pacientes (edad promedio 65 años, controlados, de forma prospectiva, con defectos acetabulares graves tipos 3A o 3B de Paprosky, por falla mecánica o infecciosa. El puntaje funcional promedio preoperatorio fue de 6,2 puntos, según la escala de Merle D ́Aubigne. Siempre se utilizaron copas de metal trabecular y aloinjertos óseos impactados. Resultados:­ A los 30 meses de seguimiento promedio (rango 24-48 meses, la supervivencia del componente acetabular fue del 95% (IC = 75%-98%. Un paciente presentó un aflojamiento acetabular por infección profunda a las 16 semanas de la revisión y fue tratado con una artroplastia de resección. El puntaje funcional promedio, excluido el caso con aflojamiento posoperatorio, fue de 16,2 puntos. Se observó la incorporación de los aloinjertos óseos en todos los pacientes, salvo el caso con infección profunda. La comparación con nuestras series históricas reconstruidas con anillos de Kerboull o con anillos GAP arrojó resultados altamente favorables a favor de las copas de metal trabecular.  Conclusiones: Las copas de metal trabecular asociadas a aloinjertos óseos impactados ofrecen una alternativa válida en cirugía de revisión acetabular con defectos graves del capital óseo. Este método se asocia a resultados más favorables que los obtenidos antes con anillos de reconstrucción.

  3. Particle migration and gap healing around trabecular metal implants

    DEFF Research Database (Denmark)

    Rahbek, O; Kold, S; Zippor, Berit

    2005-01-01

    Bone on-growth and peri-implant migration of polyethylene particles were studied in an experimental setting using trabecular metal and solid metal implants. Cylindrical implants of trabecular tantalum metal and solid titanium alloy implants with a glass bead blasted surface were inserted either i...

  4. Clinical impact of the disposable ventouse iCup? versus a metallic vacuum cup: a multicenter randomized controlled trial

    OpenAIRE

    Equy, V?ronique; David-Tchouda, Sandra; Dreyfus, Michel; Riethmuller, Didier; Vendittelli, Fran?oise; Cabaud, Victoire; Langer, Bruno; Margier, Jennifer; Bosson, Jean-Luc; Schaal, Jean-Patrick

    2015-01-01

    Background Assisted vaginal delivery by vacuum extraction is frequent. Metallic resterilizible metallic vacuum cups have been routinely used in France. In the last few years a new disposable semi-soft vacuum extraction cup, the iCup, has been introduced. Our objective was to compare maternal and new-born outcomes between this disposable cup and the commonly used Drapier-Faure metallic cup. Methods This was a multicenter prospective randomized controlled open clinical trial performed in the ma...

  5. Effects of metal-inlay thickness in polyethylene cups with metal-on-metal bearings.

    NARCIS (Netherlands)

    Verdonschot, N.J.J.; Vena, P.; Stolk, J.; Huiskes, R.

    2002-01-01

    A way to prevent polyethylene wear in total hip replacements is to use metal-on-metal bearings. The cup design of these bearings may be a metal inlay in a polyethylene cup. However, these metal inlays are relatively thin and may deform on loading. The purpose of the current study was to determine

  6. Trabecular metal acetabular components in primary total hip arthroplasty

    DEFF Research Database (Denmark)

    Laaksonen, Inari; Lorimer, Michelle; Gromov, Kirill

    2018-01-01

    included. The mean follow-up times were 3.0 years for the TM cups and 3.8 years for the other uncemented cups. Results - The overall survivorship up to 8 years for TM cups and other uncemented cups was 94.4% and 96.2%, respectively (p = regression model...

  7. Tibial component with and without stem extension in a trabecular metal cone construct

    NARCIS (Netherlands)

    Meijer, Marrigje F.; Boerboom, Alexander L.; Stevens, Martin; Reininga, Inge H.F.; Janssen, Dennis W.; Verdonschot, N.; Bulstra, Sjoerd K.

    2017-01-01

    Purpose: The purpose of this study was to investigate stability and strain distribution of a tibial plateau reconstruction with a trabecular metal cone while the tibial component is implanted with and without a stem, and whether prosthetic stability was influenced by bone mineral density. Trabecular

  8. Tibial component with and without stem extension in a trabecular metal cone construct

    NARCIS (Netherlands)

    Meijer, Marrigje F; Boerboom, Alexander L; Stevens, Martin; Reininga, Inge H F; Janssen, Dennis W; Verdonschot, N; Bulstra, Sjoerd K

    2017-01-01

    PURPOSE: The purpose of this study was to investigate stability and strain distribution of a tibial plateau reconstruction with a trabecular metal cone while the tibial component is implanted with and without a stem, and whether prosthetic stability was influenced by bone mineral density. Trabecular

  9. Clinical impact of the disposable ventouse iCup® versus a metallic vacuum cup: a multicenter randomized controlled trial.

    Science.gov (United States)

    Equy, Véronique; David-Tchouda, Sandra; Dreyfus, Michel; Riethmuller, Didier; Vendittelli, Françoise; Cabaud, Victoire; Langer, Bruno; Margier, Jennifer; Bosson, Jean-Luc; Schaal, Jean-Patrick

    2015-12-15

    Assisted vaginal delivery by vacuum extraction is frequent. Metallic resterilizible metallic vacuum cups have been routinely used in France. In the last few years a new disposable semi-soft vacuum extraction cup, the iCup, has been introduced. Our objective was to compare maternal and new-born outcomes between this disposable cup and the commonly used Drapier-Faure metallic cup. This was a multicenter prospective randomized controlled open clinical trial performed in the maternity units of five university hospitals and one community hospital in France from October 2009 to February 2013. We included consecutive eligible women with a singleton gestation of at least 37 weeks who required vacuum assisted delivery. Women were randomized to vacuum extraction using the iCup or usual Drapier-Faure metallic cup. The primary outcome was a composite criterion including both the risk of cup dysfunction and the most frequent maternal and neonatal harms: the use of other instruments after attempted vacuum extraction, caesarean section after attempted vacuum extraction, three detachments of the cup, caput succedaneum, cephalohaematoma, episiotomy and perineal tears. 335 women were randomized to the disposable cup and 333 to extraction using the metallic cup. There was no significant difference between the two groups for the primary outcome. However, failed instrumental delivery was more frequent in the disposable cup group, mainly due to detachment: 35.6 % vs 7.1 %, p < 0.0001. Conversely, perineal tears were more frequent in the metallic cup group, especially third or fourth grade perineal tears: 1.7 % versus 5.0 %, p = 0.003. There were no significant differences between the two groups concerning post-partum haemorrhage, transfer to a neonatal intensive care unit (NICU) or serious adverse events. While the disposable cup had more detachments and extraction failures than the standard metallic cup, this innovative disposable device had the advantage of fewer perineal

  10. The Use of Trabecular Metal Cones in Complex Primary and Revision Total Knee Arthroplasty.

    Science.gov (United States)

    Brown, Nicholas M; Bell, Joshua A; Jung, Edward K; Sporer, Scott M; Paprosky, Wayne G; Levine, Brett R

    2015-09-01

    Trabecular metal cones are one option for treating osseous defects during TKA. A total of 83 consecutive TKAs utilizing cones with an average of 40 months follow-up were reviewed. There were 24 males and 59 females, with an average age of 69 years old. Four were complex primary and 79 were revision procedures. Of 83 patients, 10 (12%) required repeat revision surgery (8 infections, one periprosthetic fracture, one aseptic loosening) and overall, 37 of 83 patients (45%) experienced at least one complication. Of 73 unrevised knees, 72 (99%) demonstrated radiographic evidence of osseointegration. Despite a high complication rate in this population, trabecular metal cones represent an attractive option for managing bone loss in complex primary and revision TKA with a high rate of osseointegration. Copyright © 2015 Elsevier Inc. All rights reserved.

  11. USING TRABECULAR METAL AUGMENTS FOR TOTAL HIP REPLACEMENT IN PATIENTS AFTER ACETABULAR FRACTURES

    Directory of Open Access Journals (Sweden)

    R. M. Tikhilov

    2011-01-01

    Full Text Available The authors presented the experience of treatment of two patients with hip arthritis after acetabular fracture. Both patients were treated with total hip replacement. During the operation, to manage posterior-superior bone defects of the acetabulum, augments of trabecular metal were used. Pain and limitation of motions in hip were indications for operative treatment. After a year of follow up there was no pain in hip; also recovery of motion and improved quality of life were observed.

  12. Crohn’s disease and Trabecular Metal implants: a report of two cases and literature review

    Directory of Open Access Journals (Sweden)

    C. Peron

    2015-10-01

    Full Text Available Aim The aim of the present study was to report two cases with Crohn’s disease in whom dental implants successfully osseointegrated and remained functionally stable up to 13 and 12 months of follow-up, respectively. Cases presentation In cases 1 (age 35 years and 2 (age 36 years, tooth 24 and 14, respectively, were atraumatically extracted and a particulated bone grafting material (buccal and palatal aspect of the defect and a Trabecular Metal implant (11.5 mm length, 4.7 mm diameter were inserted in each extraction socket. After implant placement and abutment connection with the final torque (25 Ncm, the provisional restoration was adapted in the oral cavity creating the emergence profile. The provisional crown was screw-retained and had slight occlusal contacts in the centric occlusion (intercuspation position. A periapical radiograph was taken as a control radiograph at the baseline. Postoperatively, antibiotics were prescribed as well as analgesics and an oral rinse was recommended. In both cases, the provisional restoration was removed after 2 weeks and replaced with a full ceramic restoration. Case-1 and case-2 were followed up after 13 months and 12 months respectively. In both cases postoperative healing was uneventful and radiographs taken at follow-up showed no evidence of crestal bone loss. Implants in both cases demonstrated an excellent clinical condition at follow-up. Conclusion Trabecular Metal implants can osseointegrate and remain functionally stable in patients with Crohn’s disease.

  13. Development and Applications of Porous Tantalum Trabecular Metal Enhanced Titanium Dental Implants

    Science.gov (United States)

    Bencharit, Sompop; Byrd, Warren C.; Altarawneh, Sandra; Hosseini, Bashir; Leong, Austin; Reside, Glenn; Morelli, Thiago; Offenbacher, Steven

    2013-01-01

    Statement of Problem Porous tantalum trabecular metal has recently been incorporated in titanium dental implants as a new form of implant surface enhancement. However, there is little information on the applications of this material in implant dentistry. Methods We, therefore review the current literature on the basic science and clinical uses of this material. Results Porous tantalum metal is used to improve the contact between osseous structure and dental implants; and therefore presumably facilitate osseointegration. Success of porous tantalum metal in orthopedic implants led to the incorporation of porous tantalum metal in the design of root-from endosseous titanium implants. The porous tantalum three-dimensional enhancement of titanium dental implant surface allows for combining bone ongrowth together with bone ingrowth, or osseoincorporation. While little is known about the biological aspect of the porous tantalum in the oral cavity, there seems to be several possible advantages of this implant design. This article reviews the biological aspects of porous tantalum enhanced titanium dental implants, in particular the effects of anatomical consideration and oral environment to implant designs. Conclusions We propose here possible clinical situations and applications for this type of dental implant. Advantages and disadvantages of the implants as well as needed future clinical studies are discussed. PMID:23527899

  14. Activation of human leukocytes on tantalum trabecular metal in comparison to commonly used orthopedic metal implant materials.

    Science.gov (United States)

    Schildhauer, T A; Peter, E; Muhr, G; Köller, M

    2009-02-01

    We analyzed leukocyte functions and cytokine response of human leukocytes toward porous tantalum foam biomaterial (Trabecular Metaltrade mark, TM) in comparison to equally sized solid orthopedic metal implant materials (pure titanium, titanium alloy, stainless steel, pure tantalum, and tantalum coated stainless steel). Isolated peripheral blood mononuclear cells (PBMC) and polymorphonuclear neutrophil leukocytes (PMN) were cocultured with equally sized metallic test discs for 24 h. Supernatants were analyzed for cytokine content by enzyme-linked immunosorbent assay. Compared to the other used test materials there was a significant increase in the release of IL (interleukin)-1ra and IL-8 from PMN, and of IL-1ra, IL-6, and TNF-alpha from PBMC in response to the TM material. The cytokine release correlated with surface roughness of the materials. In contrast, the release of IL-2 was not induced showing that mainly myeloid leukocytes were activated. In addition, supernatants of these leukocyte/material interaction (conditioned media, CM) were subjected to whole blood cell function assays (phagocytosis, chemotaxis, bacterial killing). There was a significant increase in the phagocytotic capacity of leukocytes in the presence of TM-conditioned media. The chemotactic response of leukocytes toward TM-conditioned media was significantly higher compared to CM obtained from other test materials. Furthermore, the bactericidal capacity of whole blood was enhanced in the presence of TM-conditioned media. These results indicate that leukocyte activation at the surface of TM material induces a microenvironment, which may enhance local host defense mechanisms.

  15. Evaluation of the fixation of the trabecular metal wedge in patients undergoing revision of total hip arthroplasty

    Directory of Open Access Journals (Sweden)

    Victor Magalhães Callado

    2014-08-01

    Full Text Available Objective:this study aimed to evaluate the fixation of the trabecular metal wedge in patients undergoing revision of total hip arthroplasty.Methods:twenty-three cases with minimum grading of Paprosky II-B that were operated between July 2008 and February 2013 were evaluated. These cases were evaluated based on radiographs before the operation, immediately after the operation and later on after the operation. Loss of fixation was defined as a change in the abduction angle of the component greater than 10° or any mobilization greater than 6 mm.Results:it was found that there was 100% fixation of the acetabula after a mean of 29.5 months. One case underwent removal of the implanted components due to infection.Conclusions:there is still no consensus regarding the best option for reconstructing hips with bone loss. However, revision using a trabecular metal wedge has presented excellent short-and medium-term results. This qualifies it as an important tool for achieving a fixed and stable acetabular component.

  16. Use of a trabecular metal cone made of tantalum, to treat bone defects during revision knee arthroplasty,

    Directory of Open Access Journals (Sweden)

    Alan de Paula Mozella

    2014-06-01

    Full Text Available OBJECTIVES: the aim of this study was to evaluate the surgical technique and determine the initial results, with a minimum follow-up of two years, from total knee arthroplasty revisions in which trabecular metal cones made of tantalum were used at the Knee Surgery Center of the National Institute of Traumatology and Orthopedics (INTO or at the authors' private clinic between July 2008 and December 2010.METHODS: ten patients were included in the study prospectively, through clinical and radiographic evaluations.RESULTS: seven patients presented evolution without complications relating to the tantalum cones used. Five of these patients said that they did not have any pain and all of them were able to walk without needing crutches. In all the cases, we observed that osseointegration of the tantalum cones had occurred. No migration or loosening of the implants was observed, nor was osteolysis.CONCLUSION: use of trabecular metal cones made of tantalum for treating AORI type II or II bone defects was capable of providing efficient structural support to the prosthetic revision implants, in evaluations with a short follow-up.

  17. Micro-hydromechanical deep drawing of metal cups with hydraulic pressure effects

    Science.gov (United States)

    Luo, Liang; Jiang, Zhengyi; Wei, Dongbin; Wang, Xiaogang; Zhou, Cunlong; Huang, Qingxue

    2018-03-01

    Micro-metal products have recently enjoyed high demand. In addition, metal microforming has drawn increasing attention due to its net-forming capability, batch manufacturing potential, high product quality, and relatively low equipment cost. Micro-hydromechanical deep drawing (MHDD), a typical microforming method, has been developed to take advantage of hydraulic force. With reduced dimensions, the hydraulic pressure development changes; accordingly, the lubrication condition changes from the macroscale to the microscale. A Voronoi-based finite element model is proposed in this paper to consider the change in lubrication in MHDD according to open and closed lubricant pocket theory. Simulation results agree with experimental results concerning drawing force. Changes in friction significantly affect the drawing process and the drawn cups. Moreover, defined wrinkle indexes have been shown to have a complex relationship with hydraulic pressure. High hydraulic pressure can increase the maximum drawing ratio (drawn cup height), whereas the surface finish represented by the wear is not linearly dependent on the hydraulic pressure due to the wrinkles.

  18. Synthesis of Stacked-Cup Carbon Nanotubes in a Metal Free Low Temperature System

    Science.gov (United States)

    Kimura, Yuki; Nuth, Joseph A.; Johnson, Natasha M.; Farmer, Kevin D.; Roberts, Kenneth P.; Hussaini, Syed R.

    2011-01-01

    Stacked-cup carbon nanotubes were formed by either Fischer-Tropsch type or Haber Bosch type reactions in a metal free system. Graphite particles were used as the catalyst. The samples were heated at 600 C in a gas mixture of CO 75 Torr, N2 75 Torr and H2 550 Torr for three days. Trans mission electron microscope analysis of the catalyst surface at the completion of the experiment recognized the growth of nanotubes. They were 10-50 nm in diameter and approximately 1 micrometer in length. They had a hollow channel of 5-20 nm in the center. The nanotubes may have grown on graphite surfaces by the CO disproportionation reaction and the surface tension of the carbon nucleus may have determined the diameter. Although, generally, the diameter of a carbon nanotube depends on the size of the cataly1ic particles, the diameter of the nanotubes on graphite particles was independent of the particle size and significantly confined within a narrow range compared with that produced using catalytic amorphous iron-silicate nanoparticles. Therefore, they must have an unknown formation process that is different than the generally accepted mechanism.

  19. Immediate loading of trabecular metal-enhanced titanium dental implants: interim results from an international proof-of-principle study.

    Science.gov (United States)

    Schlee, Marcus; van der Schoor, W Peter; van der Schoor, Alexandra R M

    2015-01-01

    A 3-year proof-of-principle study was initiated to evaluate the clinical efficacy of immediately loading titanium dental implants with surfaces enhanced with porous tantalum trabecular metal (PTTM). First-year interim results are presented. Healthy, partially edentulous patients (n = 30) were enrolled and treated per protocol (minimum insertion torque: ≥35 Ncm) with 37 implants placed in one or two premolar or molar locations in either jaw (study group). Implants were immediately provisionalized out of occlusion with single acrylic crowns. After 7 to 14 days of soft tissue healing, implants were definitively restored in occlusion with ceramometal crowns. Because most study group implants (54.1%, n = 20) had less than 1 year of clinical follow-up, this interim analysis was limited to the first 22 consecutively placed implants in 17 subjects (10 women and 7 men) who completed 1 year of clinical follow-up to date (focus group). To date, one implant failed to integrate in the study group (survival = 97.3%, n = 36/37). Focus group implants achieved 100% (n = 22/22) survival with 0.43 ± 0.41 mm of mean marginal bone loss. There were no serious complications. Early clinical findings indicated that immediate loading of PTTM implants was safe and effective under the controlled study conditions. © 2013 The Authors. Clinical Implant Dentistry and Related Research published by Wiley Periodicals, Inc.

  20. Analytical evaluation of a cup-horn sonoreactor used for ultrasound-assisted extraction of trace metals from troublesome matrices

    Science.gov (United States)

    De La Calle, Inmaculada; Cabaleiro, Noelia; Lavilla, Isela; Bendicho, Carlos

    2009-09-01

    In this work, a sample preparation method based on ultrasound-assisted extraction of trace metals from a variety of biological and environmental matrices using a cup-horn sonoreactor is described. Diluted acids (HNO 3, HCl and HF) and oxidants (H 2O 2) were tried for extraction, the extracts being directly analyzed by electrothermal-atomic absorption spectrometry. The cup-horn sonoreactor combines the advantages of probe and bath sonicators, allowing a variety of conditions to be used for metal extraction from troublesome matrices. This system facilitates the use of HF to destroy the silicate lattice, application of simultaneous treatments of up to six samples and short treatment times. Quantitative metal recoveries are achieved from different matrices (animal and vegetal tissues, soil, sediment, fly ash, sewage sludge) under a set of extraction conditions ranging from the use of 3 min sonication time and 3% volume/volume HNO 3 for some animal tissues to 40 min sonication time along with 5% volume/volume HNO 3 + 20% volume/volume HF for sediment. Vegetal matter required the use of 5% volume/volume HNO 3 + 5% volume/volume HF for extraction of some elements. Ultrasound-assisted extraction of Cd, Mn, Pb, Ni and Cr from 16 certified reference materials representing a variety of biological and environmental matrices using the cup-horn sonoreactor is evaluated. Cd, Pb and Mn are more easily extracted from most certified reference materials (CRMs) than Cr and Ni and less stringent conditions can be chosen for the former metals. Metal extractability follows the order of difficulty: animal tissue fly ash, sewage sludge < sediment.

  1. Analytical evaluation of a cup-horn sonoreactor used for ultrasound-assisted extraction of trace metals from troublesome matrices

    International Nuclear Information System (INIS)

    De La Calle, Inmaculada; Cabaleiro, Noelia; Lavilla, Isela; Bendicho, Carlos

    2009-01-01

    In this work, a sample preparation method based on ultrasound-assisted extraction of trace metals from a variety of biological and environmental matrices using a cup-horn sonoreactor is described. Diluted acids (HNO 3 , HCl and HF) and oxidants (H 2 O 2 ) were tried for extraction, the extracts being directly analyzed by electrothermal-atomic absorption spectrometry. The cup-horn sonoreactor combines the advantages of probe and bath sonicators, allowing a variety of conditions to be used for metal extraction from troublesome matrices. This system facilitates the use of HF to destroy the silicate lattice, application of simultaneous treatments of up to six samples and short treatment times. Quantitative metal recoveries are achieved from different matrices (animal and vegetal tissues, soil, sediment, fly ash, sewage sludge) under a set of extraction conditions ranging from the use of 3 min sonication time and 3% volume/volume HNO 3 for some animal tissues to 40 min sonication time along with 5% volume/volume HNO 3 + 20% volume/volume HF for sediment. Vegetal matter required the use of 5% volume/volume HNO 3 + 5% volume/volume HF for extraction of some elements. Ultrasound-assisted extraction of Cd, Mn, Pb, Ni and Cr from 16 certified reference materials representing a variety of biological and environmental matrices using the cup-horn sonoreactor is evaluated. Cd, Pb and Mn are more easily extracted from most certified reference materials (CRMs) than Cr and Ni and less stringent conditions can be chosen for the former metals. Metal extractability follows the order of difficulty: animal tissue < vegetal tissue < soil, fly ash, sewage sludge < sediment.

  2. Outcome of revision total knee arthroplasty with the use of trabecular metal cone for reconstruction of severe bone loss at the proximal tibia

    DEFF Research Database (Denmark)

    Jensen, Claus L; Olsen, Nikolaj Winther; Schrøder, Henrik M

    2014-01-01

    BACKGROUND: The relative effectiveness of different methods for reconstructing large bone loss at the proximal tibia in revision total knee arthroplasty (rTKA) has not been established. The aim of this study was to evaluate the clinical and radiological outcome after the use of trabecular metal......). RESULTS: Clinical and radiological follow-up data were available in 30 patients and missing in six patients: two died and four patients had re-revision (reinfection (n=2), aseptic loosening (n=1), and knee hyperextension (n=1)). Knee- and function scores (follow-up 43 months (range 12-84 months)) improved...... treatment in terms of surgical efficacy, clinical results and radiological results and was evidently at least as effective as the other options reviewed in the literature. LEVEL OF EVIDENCE: IV....

  3. [Application of minimally invasive, decompression bone graft implantation combined with metal trabecular bone reconstruction system for early stage osteonecrosis of femoral head].

    Science.gov (United States)

    Chen, Xian-tao; Tan, Xu-yi; Liu, You-wen; Zhang, Xiao-dong; Liu, Li-yun; Jia, Yu-dong

    2015-05-01

    To observe the application effect of minimally invasive decompression, bone graft implantation and metal trabecular bone reconstruction system for early stage osteonecrosis of femoral head and discuss the treatment of hip-salvage operation in early stage osteonecrosis of femoral head; From January 2010 to June 2011, 50 patients (62 hips) Which were osteonecrosis of femoral head of early stake,were treated with minimally invasive decompression, bone graft implantation and metal trabecular bone reconstruction system, including 31 males (40 hips), 19 females (22 hip) with an average age of 36.2 years old ranging from 22 to 54 years old. The course of disease was from 6 to 15 months (averaged 10.5 months). Among them, 19 cases (23 hips) were steroid-induced, 25 cases (33 hips) were alcohol-induced, 6 cases (6 hips) were idiopathic; According to ARCO stage, 28 hips were at stage I, 34 hips were at stage II. All of them were diagnosed as femoral head necrosis by imaging examination before operation. Then each patient was followed to assess by Harris hip score, curative effect, and conduct the femoral head survival analysis during the postoperation. All patients had finished operation, the operation time was between 30 and 85 min, intraoperative blood loss was 50 to 220 ml, and 47 cases (58 hips) were follow-up from 24 to 46 months with an average of 34.05 months. As compared with preoperative, the Harris hip score at the last follow-up was improved, the difference was statistically significant (Pfemoral head in ARCO stage I was superior to these in ARCO Stage II, the difference was statistically significant (Posteonecrosis of femoral head was good,it could significantly improve the Harris hip score, increase the femoral head survival time, delay the hip replacement, and performance better in ARCO stage I.

  4. On Parameters Affecting Metal Flow and Friction in the Double Cup Extrusion Test

    DEFF Research Database (Denmark)

    Tan, Xincai; Bay, Niels; Zhang, Wenqi

    1998-01-01

    Friction and lubrication in metal-forming processes are usually evaluated by a process test with a friction-sensitive divided flow like the ring-compression test. Parameters affecting metal flow are not only friction, but also strain hardening, tool geometry etc. The current friction models appli...

  5. Analysis of bone ingrowth on a tantalum cup

    Directory of Open Access Journals (Sweden)

    D′Angelo F

    2008-01-01

    Full Text Available Background: Trabecular Metal (TM is a new highly porous material made of tantalum (Zimmer, Warsaw, Indiana, USA. Its three-dimensional structure is composed of a series of interconnected dodecahedron pores that are on average 550 μm in diameter. This size is considered optimal for bone ingrowth and is similar to trabecular bone. The elastic modulus of TM (3 GPa is more similar to that of cancellous (0,1-1,5 GPa or cortical (112-18 GPa bone and is significantly less similar to that of Titanium (110 GPa and Co-Cr alloys (220 GPa. These features enable bone apposition and remodeling. The purpose of the present study was to evaluate the histology of the bone-implant interface in a human specimen. Materials and Methods: A highly porous tantalum cup (Zimmer, Warsaw, Indiana, USA was removed for recurrent dislocations three years after implantation. In order to obtain a slice of the cup, two cuts were made on the centre using an Exakt cutting machine. Then the slice was embedded in a Technovit resin and a Hematoxylin-eosin stain was used to study the bone tissue. Bone ingrowth was calculated using a method based on simple calculations of planar geometry. Results: The histological evaluation of the periprosthetic tissues revealed a typical chronic inflammation with few particles of polyethylene that were birefringent using polarized light. The quantitative evaluation of bone ingrowth revealed that more than 95% of voids were filled with bone. Discussion: In the literature, a lot of studies focused on tantalum were carried on animal model. Up to now little information is available about the histology of the bone-tantalum interface in a human artificial joint. We had an opportunity to remove a well integrated cup hence this study. The histology confirmed the strong relationship between the structure of this material and bone. The morphometric analysis revealed a high percentage of bone ingrowth.

  6. Human bone ingrowth into a porous tantalum acetabular cup

    Directory of Open Access Journals (Sweden)

    Gregory N. Haidemenopoulos

    2017-11-01

    Full Text Available Porous Tantalum is increasingly used as a structural scaffold in orthopaedic applications. Information on the mechanisms of human bone ingrowth into trabecular metal implants is rather limited. In this work we have studied, qualitatively, human bone ingrowth into a retrieved porous tantalum monoblock acetabular cup using optical microscopy, scanning electron microscopy and energy dispersive X-ray analysis. According to the results and taking into account the short operational life (4 years of the implant, bone ingrowth on the acetabular cup took place in the first two-rows of porous tantalum cells to an estimated depth of 1.5 to 2 mm. The bone material, grown inside the first raw of cells, had almost identical composition with the attached bone on the cup surface, as verified by the same Ca:P ratio. Bone ingrowth has been a gradual process starting with Ca deposition on the tantalum struts, followed by bone formation into the tantalum cells, with gradual densification of the bone tissue into hydroxyapatite. A critical step in this process has been the attachment of bone material to the tantalum struts following the topology of the porous tantalum scaffold. These results provide insight to the human bone ingrowth process into porous tantalum implants.

  7. Cup-cage construct for acute fractures of the acetabulum, re-defining indications.

    Science.gov (United States)

    Chana-Rodríguez, Francisco; Villanueva-Martínez, Manuel; Rojo-Manaute, Jose; Sanz-Ruíz, Pablo; Vaquero-Martín, Javier

    2012-12-01

    Acetabular fractures in the elderly are challenging injuries. The use of a trabecular metal acetabular cage was investigated as the treatment option in a series of elderly patients with acetabular fractures. At a 2-year follow up, 6 elderly patients were found to have mimimum pain, increased function, and increased scores using the Merle d'Aubigné and Postel system modified by Charnley. Radiographically, the areas of morsellised autograft that surrounded the cups were seen to have incorporated uniformly well, and the acetabular fractures were healed within six months after surgery. No mechanical failure, screw breakage, loosening, or migration was noticed. This novel indication of the cup-cage construction that uses revision techniques, for selected patients and fractures, to achieve an acute stable reconstruction, should be considered as an alternative reconstruction option in elderly patients presenting with acetabular fractures. Copyright © 2012 Elsevier Ltd. All rights reserved.

  8. Immediate placement of a porous-tantalum, trabecular metal-enhanced titanium dental implant with demineralized bone matrix into a socket with deficient buccal bone: a clinical report.

    Science.gov (United States)

    Bencharit, Sompop; Byrd, Warren C; Hosseini, Bashir

    2015-04-01

    A missing or deficient buccal alveolar bone plate is often an important limiting factor for immediate implant placement. Titanium dental implants enhanced with porous tantalum-based trabecular metal material (PTTM) are designed for osseoincorporation, a combination of vascularized bone ingrowth and osseointegration (bone on-growth). Demineralized bone matrix (DBM) contains growth factors with good handling characteristics. However, the combination of these 2 materials in facial alveolar bone regeneration associated with immediate implant therapy has not been reported. A 65-year-old Asian woman presented with a failing central incisor. Most of the buccal alveolar bone plate of the socket was missing. A PTTM enhanced implant was immediately placed with DBM. Cone beam computed tomography scans 12 months after the insertion of the definitive restoration showed regeneration of buccal alveolar bone. A combination of a PTTM enhanced implant, DBM, and a custom healing abutment may have an advantage in retaining biologically active molecules and form a scaffold for neovascularization and osteogenesis. This treatment protocol may be a viable option for immediate implant therapy in a failed tooth with deficient buccal alveolar bone. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  9. Total hip arthroplasty revision by dual-mobility acetabular cup cemented in a metal reinforcement: A 62 case series at a minimum 5 years' follow-up.

    Science.gov (United States)

    Lebeau, N; Bayle, M; Belhaouane, R; Chelli, M; Havet, E; Brunschweiler, B; Mertl, P

    2017-09-01

    Total hip arthroplasty (THA) requires bone reconstruction in case of severe acetabular injury, with risk of dislocation, especially postoperatively. Dual-mobility cups have proved effective in preventing dislocation in THA revision for instability, but their behavior when cemented in a metal reinforcement has been little studied. The present study assessed results for a dual-mobility cup cemented in a metal reinforcement, in terms of aseptic loosening and postoperative instability. A single-center continuous series of 62 patients receiving such an assembly in THA revision was assessed retrospectively at a minimum 5 years' follow-up. Failure due to aseptic loosening or instability and implant survival at last follow-up were analyzed. Radiological and clinical analysis was performed at a mean 77 months' follow-up. Mean Merle-d'Aubigné-Postel score was 14, Harris score 73 and Oxford-12 score 23.9 at last follow-up. Complications comprised 5 cases of loosening and 2 of dislocation. Loosening risk was significantly greater in case ofrevision with severe bone loss. IV, retrospective study. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  10. Hemiarthroplasty for the treatment of complex proximal humeral fractures: does a trabecular metal prosthesis make a difference? A prospective, comparative study with a minimum 3-year follow-up.

    Science.gov (United States)

    Li, Fenglong; Zhu, Yiming; Lu, Yi; Liu, Xin; Wu, Guan; Jiang, Chunyan

    2014-10-01

    Proper positioning and healing of the greater tuberosity are key for functional shoulder recovery after hemiarthroplasty for complex proximal humeral fractures. The purpose of this study was to compare the outcomes after hemiarthroplasty between a trabecular metal prosthesis and a conventional prosthesis in the treatment of complex proximal humeral fractures. A prospective, comparative study was performed. We compared a trabecular metal shoulder prosthesis for the treatment of complex proximal humeral fractures in a cohort of 35 consecutive patients (TM group) with a conventional prosthesis in a cohort of 38 consecutive patients (conventional group). All the patients, with a mean age of 63.9 years, were prospectively followed-up for a mean time of 4.6 years (range, 3-6 years) after surgery. At the last follow-up, radiographic complication rates related to the greater tuberosity were lower in the TM group (6.1%) than in the conventional group (25.7%) (P = .028). The mean functional shoulder scores, as well as mean active forward elevation and external rotation, were better in the TM group than in the conventional group. Radiographic complication rates related to the greater tuberosity were significantly lower in the TM group than in the conventional group. The functional shoulder scores and active forward elevation and external rotation were all better in the TM group than in the conventional group. These findings could imply better healing potential of the greater tuberosity after hemiarthroplasty with a trabecular metal prosthesis to treat complex proximal humeral fractures. Copyright © 2014 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

  11. "Greening" a Familiar General Chemistry Experiment: Coffee Cup Calorimetry to Determine the Enthalpy of Neutralization of an Acid-Base Reaction and the Specific Heat Capacity of Metals

    Science.gov (United States)

    Bopegedera, A. M. R. P.; Perera, K. Nishanthi R.

    2017-01-01

    Coffee cup calorimetry, performed with calorimeters made with styrofoam coffee cups, is a familiar experiment in the general chemistry laboratory. These calorimeters are inexpensive, easy to use, and provide good insulation for most thermodynamics experiments. This paper presents the successful substitution of paper coffee cups for styrofoam cups…

  12. Menses cup evaluation study.

    Science.gov (United States)

    Cheng, M; Kung, R; Hannah, M; Wilansky, D; Shime, J

    1995-09-01

    To determine whether the menses cup is well tolerated by menstruating women. Prospective descriptive clinical study. Normal human volunteers in an academic research environment. Fifty-one menstruating women recruited between June to December 1991. Each participant was provided with two menses cups and an instruction sheet. Baseline information, including age, occupation, martial status, parity, description of menstrual flow, and current method used to cope with menstrual flow was collected. Subjects were asked to describe their experience with the cup at 1-, 2-, 6-, and 12-month intervals. The proportion of women who found the cup acceptable. The cup was used by 51 subjects for a total of 159 cycles. Overall, 23 women (45%) found the cup an acceptable method for coping with menses. Among 29 (57%) women who used the cup for two or more cycles, 62% found it acceptable. The menses cup may be an acceptable method for some women for coping with menstrual flow.

  13. Mucopolysaccharides in the trabecular meshwork

    International Nuclear Information System (INIS)

    Ohnishi, Yoshitaka; Yamana, Yasuo; Abe, Masahiro

    1982-01-01

    The localization of 35 S-sulfate and 3 H-glucosamine in the trabecular region of the hamster was studied by light and electron microscopic autoradiography after the intraperitoneal injection. Exposed silver grains of 35 S-sulfate were concentrated in the trabecular meshwork, sclera and cornea, and grains of 35 H-glucosamine were localized in the trabecular region. The radioactivity of both isotopes was observed in the Golgi apparatuses of the endothelial cells and fibroblasts in Schlemm's canal and the trabecular meshwork. Thereafter, the grains were noted over the entire cytoplasm, except for the nucleus, and then were incorporated into the amorphous substance and collagen fibers in the juxtacanalicular connective tissue. These results suggest that endothelial cells in the trabecular region synthesize and secrete the sulfated mucopolysaccharides and hyaluronic acid. (author)

  14. Development and initial validation of a novel smoothed-particle hydrodynamics-based simulation model of trabecular bone penetration by metallic implants.

    Science.gov (United States)

    Kulper, Sloan A; Fang, Christian X; Ren, Xiaodan; Guo, Margaret; Sze, Kam Y; Leung, Frankie K L; Lu, William W

    2017-09-14

    A novel computational model of implant migration in trabecular bone was developed using smoothed-particle hydrodynamics (SPH), and an initial validation was performed via correlation with experimental data. Six fresh-frozen human cadaveric specimens measuring 10 × 10 × 20 mm were extracted from the proximal femurs of female donors (mean age of 82 years, range 75-90, BV/TV ratios between 17.88% and 30.49%). These specimens were then penetrated under axial loading to a depth of 10 mm with 5 mm diameter cylindrical indenters bearing either flat or sharp/conical tip designs similar to blunt and self-tapping cancellous screws, assigned in a random manner. SPH models were constructed based on microCT scans (17.33 µm) of the cadaveric specimens. Two initial specimens were used for calibration of material model parameters. The remaining four specimens were then simulated in silico using identical material model parameters. Peak forces varied between 92.0 and 365.0 N in the experiments, and 115.5-352.2 N in the SPH simulations. The concordance correlation coefficient between experimental and simulated pairs was 0.888, with a 95%CI of 0.8832-0.8926, a Pearson ρ (precision) value of 0.9396, and a bias correction factor Cb (accuracy) value of 0.945. Patterns of bone compaction were qualitatively similar; both experimental and simulated flat-tipped indenters produced dense regions of compacted material adjacent to the advancing face of the indenter, while sharp-tipped indenters deposited compacted material along their peripheries. Simulations based on SPH can produce accurate predictions of trabecular bone penetration that are useful for characterizing implant performance under high-strain loading conditions. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

  15. Transfer of metallic debris from the metal surface of an acetabular cup to artificial femoral heads by scraping: comparison between alumina and cobalt-chrome heads.

    Science.gov (United States)

    Chang, Chong Bum; Yoo, Jeong Joon; Song, Won Seok; Kim, Deug Joong; Koo, Kyung-Hoi; Kim, Hee Joong

    2008-04-01

    We aimed to investigate the transfer of metal to both ceramic (alumina) and metal (cobalt-chrome) heads that were scraped by a titanium alloy surface under different load conditions. The ceramic and metal heads for total hip arthroplasties were scraped by an acetabular metal shell under various loads using a creep tester. Microstructural changes in the scraped area were visualized with a scanning electron microscope, and chemical element changes were assessed using an energy dispersive X-ray spectrometry. Changes in the roughness of the scraped surface were evaluated by a three-dimensional surface profiling system. Metal transfer to the ceramic and metal heads began to be detectable at a 10 kg load, which could be exerted by one-handed force. The surface roughness values significantly increased with increasing test loads in both heads. When the contact force increased, scratching of the head surface occurred in addition to the transfer of metal. The results documented that metallic debris was transferred from the titanium alloy acetabular shell to both ceramic and metal heads by minor scraping. This study suggests that the greatest possible effort should be made to protect femoral heads, regardless of material, from contact with metallic surfaces during total hip arthroplasty.

  16. A retained menstrual cup.

    Science.gov (United States)

    Day, S

    2012-05-01

    A 20-year-old woman attended a genitourinary clinic with a retained vaginal Mooncup that she had inserted the night before. A Mooncup is one type of menstrual cup. On speculum examination the device was visualized high in the vagina and the cervix appeared firmly lodged within it. The physician experienced difficulty in retrieving the cup despite following product instructions. This case highlights a new adverse event with an increasingly used sanitation product. It is important that clinicians are familiar with the cup, its removal process and are able to counsel patients with retained devices on future correct placement.

  17. Brazil World Cup Challenges

    Directory of Open Access Journals (Sweden)

    MANSUR, R.

    2012-12-01

    Full Text Available Overcoming the productivity challenge is the main benefit of the 2014 World Cup for Brazilian people. The sustainable development of our cultural tourism industry will catapult the new middle class growing up rate.

  18. [Endometrial cups in horses].

    Science.gov (United States)

    Jacobs, P H; Elsinghorst, T A

    1987-04-01

    Endometrial cups in horses are outgrowths appearing in the uterine wall of the pregnant horn between approximately 38 days and 150 of gestation. The cups are structures which vary in shape from oval to irregular and have distinct raised edges, showing an ulcer-like form. The maximum measurements are approximately 5 X 2.5 X 2.5 cm. Microscopic examination shows that they consist of large epithelioid decidual-like cells having large nucleoli. Pregnant Mare Endometrium Gonadotrophin (PMEG) is produced in the endometrial cups. PMEG may be regarded as a precursor of Pregnant Mare Serum Gonadotrophin (PMSG), which can be detected in the blood of mares. The exact function of PMSG is still obscure; some possible functions are suggested in the present paper. After approximately 70 days of gestation, regression starts. The regression of the cups is an immunological process in which the cellular branch of the immunological system plays an important role. Humoral immunity plays a more protective role in the process of regression, probably as a result of the production of 'blocking' antibodies.

  19. Complementary Coffee Cups

    Science.gov (United States)

    Banchoff, Thomas

    2006-01-01

    What may have been the birth of a new calculus problem took place when the author noticed that two coffee cups, one convex and one concave, fit nicely together, and he wondered which held more coffee. The fact that their volumes were about equal led to the topic of this article: complementary surfaces of revolution with equal volumes.

  20. Migration of the Duraloc cup after 5 years

    Science.gov (United States)

    Stihsen, Christoph; Pabinger, Christof; Radl, Roman; Rehak, Peter

    2007-01-01

    The Duraloc cup is a frequently used metal-backed, porous-coated, hemispherical, press-fit acetabular component. Published data on loosening rates are contradictory. In this study we investigated migration patterns with computer-assisted Einzel-Bild-Roentgen-Analyse (EBRA) of 67 Duraloc 100 cups. Cup migration and clinical scores were analysed over a 5-year follow-up period. Median total migration of the Duraloc 100 cup was 1.21 mm at 5 years. Seventy-five percent of implants were radiologically stable at 2 years and 90% at 4 years. One cup loosened aseptically at 60 months, requiring revision. Cup diameters ≥54 mm migrated significantly more than cups <54 mm in diameter (p = 0.029 at 4 years). There was a significant correlation between high polyethylene wear and further migrating cups within the first post-operative year (p = 0.035 at 12 months). Our analysis revealed significantly higher wear in males (p = 0.029 at 4 years). Radiological loosening at two years could be calculated using receiver-operating characteristic curve analysis, and 1.2 mm as an adequate threshold value (sensitivity = 100%, specificity = 89%). PMID:17609953

  1. Outcome of Revision Total Hip Arthroplasty in Management of Failed Metal-on-Metal Hip Arthroplasty.

    Science.gov (United States)

    Rahman, Wael A; Amenábar, Tomás; Hetaimish, Bandar M; Safir, Oleg A; Kuzyk, Paul R; Gross, Allan E

    2016-11-01

    This is a retrospective review of the functional outcomes and complications of revision total hip arthroplasty (THA) of failed metal-on-metal (MoM) hip arthroplasty. A total of 20 revision THAs were performed in 19 patients. Of them, 2 cases were failed hip resurfacing, and 18 cases were failed (MoM) THA. The mean age at revision (THA) was 59.35 years (standard deviation [SD] 9.83). The mean follow-up was 45 months (SD 13.98). The indications of revision were aseptic loosening of acetabular component without adverse local tissue reaction (ALTR; 10 hips), aseptic loosening of the acetabular and femoral components without ALTR (1 hip), painful hip associated with ALTR (6 hips), iliopsoas impingement associated with a large-diameter femoral head or malpositioned acetabular component (3 hips). The acetabular components were revised in 18 hips using Trabecular Metal Modular cups. The femoral components were revised in 3 hips. A constrained acetabular liner was used in 5 hips. The Harris hip score significantly improved from 48.4 (SD 12.98) to 83.25 (SD 10.08). There were 2 complications (1 foot drop and 1 superficial infection) and 1 failure (recurrent dislocation) that required revision to a constrained liner. Early results of revision THA of failed MoM hip arthroplasty showed improvement in pain and functional outcome. No case of failed bone ingrowth was noted with the use of Trabecular Metal Modular cups. Extensive soft tissue and abductor muscles dysfunctions were common. A constrained acetabular component with repair of the hip abductors might be beneficial. Copyright © 2016 Elsevier Inc. All rights reserved.

  2. Field calibration of cup anemometers

    DEFF Research Database (Denmark)

    Schmidt Paulsen, Uwe; Mortensen, Niels Gylling; Hansen, Jens Carsten

    2007-01-01

    A field calibration method and results are described along with the experience gained with the method. The cup anemometers to be calibrated are mounted in a row on a 10-m high rig and calibrated in the free wind against a reference cup anemometer. The method has been reported [1] to improve...... the statistical bias on the data relative to calibrations carried out in a wind tunnel. The methodology is sufficiently accurate for calibration of cup anemometers used for wind resource assessments and provides a simple, reliable and cost-effective solution to cup anemometer calibration, especially suited...

  3. [Innovation of characteristic medicinal cupping devices].

    Science.gov (United States)

    Li, Jianping; Zhang, Hui; Yang, Jianmei; Xu, Xinchun; Niu, Yanxia; Cai, Jun

    2015-08-01

    To compare the differences in the characteristic medicinal cupping therapy between the traditional cupping device and the innovated cupping device. Fifty patients of neck and low back pain were selected. The self-comparison was adopted. The cupping therapy was applied to the acupoints located on the left or right side with the traditional cupping device and the innovated cupping device. The cupping sites were centered at bilateral Quyuan (SI 13) and Dachangshu (BL 25). The cups were retained for 10 min. The traditional cupping device was the glass with smooth border, 100mL. The innovated cupping device was the vacuum-sucking cup. The operative time, medicinal leakage, comfort and cupping marks were observed for the two different cupping devices. The operative time with the innovated medicinal cupping device was shorter obviously compared with the traditional one at Quyuan (SI 13) and Dachangshu (BL 25, both Pcupping device was remarkably improved as compared with the traditional one at the two acupoints (both Pcupping operation (both P>0. 05). The cupping marks with the innovated medicinal cupping device were much deeper than those with the traditional one after cupping therapy. The innovated cupping device is more convenent and comfortable in operation during the characteristic medicinal cupping therapy.

  4. World Cup Hopes

    Science.gov (United States)

    2002-01-01

    From May 31 to June 30 the biggest single-sport event in the world, the 2002 FIFA World Cup (tm), will be taking place in Asia. South Korea and Japan are acting as hosts for the event which is being held in Asia for the first time. This true-color image of the southern Korean peninsula and southern Japan was acquired on May 25, 2002, by the Moderate-resolution Imaging Spectroradiometer (MODIS), flying aboard NASA's Terra satellite. Thirty-two nations are represented at this year's Finals including the 1998 champion France, European powers England and Italy, tournament favorite Argentina, and the United States. The finals are the culmination of a 2-year qualifying process which started with 132 nations competing in regional qualification tournaments. In the round-robin first round of the World Cup, the U.S. team will be competing against teams from Portugal, Poland, and South Korea. Image courtesy Jacques Descloitres, MODIS Land Rapid Response Team at NASA GSFC

  5. [Application of blistering cupping].

    Science.gov (United States)

    Gu, Xingui; Chen, Zelin; Chen, Bo; Fan, Yihua; Chen, Xianghong

    2016-11-12

    Blistering cupping is special as eliminating wind and dampness as well as removing phlegm and blood stasis, and it achieves effects through suction. In this paper we reviewed relevant literature combined with clinical experience so as to summarize its operation attention through exploring the origin, mechanism and application. We divide the progress into the blistering period, the phlegm-stasis-eliminating period, and the escharosis period according to the changes of bubble and the things pulled out. Blistering cupping creates ways to eliminate concrete unhealthy influences through smoothing meridians and collaterals, such as phlegm and retained fluid, dampness and blood stasis. Thus chronic diseases are relieved. Also,we propose the rules of "blistering acupoints being related to disease location as well as the nature of acupoints and diseases". The therapy has been used to treat diseases of respiratory system, osteoarticular, skin and subcutaneous tissue, mental and behavioral disorders, and tumor, among which the effects of intractable diseases of respiratory and osteoarticular systems are definite. It deserves to be further explored and promoted.

  6. Cup Cylindrical Waveguide Antenna

    Science.gov (United States)

    Acosta, Roberto J.; Darby, William G.; Kory, Carol L.; Lambert, Kevin M.; Breen, Daniel P.

    2008-01-01

    The cup cylindrical waveguide antenna (CCWA) is a short backfire microwave antenna capable of simultaneously supporting the transmission or reception of two distinct signals having opposite circular polarizations. Short backfire antennas are widely used in mobile/satellite communications, tracking, telemetry, and wireless local area networks because of their compactness and excellent radiation characteristics. A typical prior short backfire antenna contains a half-wavelength dipole excitation element for linear polarization or crossed half-wavelength dipole elements for circular polarization. In order to achieve simultaneous dual circular polarization, it would be necessary to integrate, into the antenna feed structure, a network of hybrid components, which would introduce significant losses. The CCWA embodies an alternate approach that entails relatively low losses and affords the additional advantage of compactness. The CCWA includes a circular cylindrical cup, a circular disk subreflector, and a circular waveguide that serves as the excitation element. The components that make it possible to obtain simultaneous dual circular polarization are integrated into the circular waveguide. These components are a sixpost polarizer and an orthomode transducer (OMT) with two orthogonal coaxial ports. The overall length of the OMT and polarizer (for the nominal middle design frequency of 2.25 GHz) is about 11 in. (approximately equal to 28 cm), whereas the length of a commercially available OMT and polarizer for the same frequency is about 32 in. (approximately equal to 81 cm).

  7. Cup Anemometer Overspeeding

    DEFF Research Database (Denmark)

    Busch, N. E.; Kristensen, Leif

    1976-01-01

    Statistical considerations are applied to a general equation of motion for cup anemometers in a turbulent wind. It is shown that the relative overspeeding ΔS/S can be expressed as ΔS/S = Ih2 · Js(l0/Λs) + cIw2, where Is and Iw are the horizontal and the vertical turbulence intensifies, respectively....... The function Js depends on the shape of the spectrum of horizontal turbulent energy, l0 is the distance constant for the anemometer, and Λs is a characteristic length scale of the horizontal turbulence. The constant c is of order unity. If Λs is suitably chosen as the scale of the energy-containing eddies...

  8. Modeling of Sheet Metal Forming Based on Implicit Embedding of the Elasto-Plastic Self-Consistent Formulation in Shell Elements: Application to Cup Drawing of AA6022-T4

    Science.gov (United States)

    Zecevic, Milovan; Knezevic, Marko

    2017-05-01

    This article is concerned with multilevel simulations in sheet metal forming using a physically based polycrystalline homogenization model that takes into account microstructure and the directionality of deformation mechanisms acting at single-crystal level. The polycrystalline-level model is based on the elasto-plastic self-consistent (EPSC) homogenization of single-crystal behavior providing a constitutive response at each material point, within a boundary value problem solved using shell elements at the macro-level. A recently derived consistent tangent stiffness is adapted here to facilitate the coupling between EPSC and the implicit shell elements. The underlining EPSC model integrates a hardening law based on dislocation density, which is calibrated to predict anisotropic hardening, linear and nonlinear unloading, and the Bauschinger effect on the load reversal for AA6022-T4. To illustrate the potential of the coupled multilevel finite element elasto-plastic self-consistent (FE-EPSC) model, a simulation of cup drawing from an AA6022-T4 sheet is performed. Results and details of the approach are described in this article.

  9. On cup anemometer rotor aerodynamics.

    Science.gov (United States)

    Pindado, Santiago; Pérez, Javier; Avila-Sanchez, Sergio

    2012-01-01

    The influence of anemometer rotor shape parameters, such as the cups' front area or their center rotation radius on the anemometer's performance was analyzed. This analysis was based on calibrations performed on two different anemometers (one based on magnet system output signal, and the other one based on an opto-electronic system output signal), tested with 21 different rotors. The results were compared to the ones resulting from classical analytical models. The results clearly showed a linear dependency of both calibration constants, the slope and the offset, on the cups' center rotation radius, the influence of the front area of the cups also being observed. The analytical model of Kondo et al. was proved to be accurate if it is based on precise data related to the aerodynamic behavior of a rotor's cup.

  10. Metaphyseal cupping: a case report.

    Science.gov (United States)

    Wiss, D A

    1981-06-01

    A case of metaphyseal cupping of bone that probably occurred as the result of an impaired blood supply to the leg of an infant is reported. Avascularity and premature closure of the central segment of the growth plate is the proposed pathogenesis. The blood supply, growth and development of the ends of growing bones are discussed and the radiographie features of metaphyseal cupping are described. Copyright 2013, SLACK Incorporated.

  11. Minimum Five-Year Outcomes with Porous Tantalum Acetabular Cup and Augment Construct in Complex Revision Total Hip Arthroplasty.

    Science.gov (United States)

    Jenkins, Derek R; Odland, Andrew N; Sierra, Rafael J; Hanssen, Arlen D; Lewallen, David G

    2017-05-17

    The use of a trabecular metal revision shell with metal augmentation to fill segmental or irregular defects during complex revision hip arthroplasty has been shown to provide good short-term results in prior published series. Longer-term results of the several cup-augment constructs used clinically are not known. The objective of this study was to report, with minimum 5-year radiographic and clinical follow-up, the outcome of these various constructs in revision total hip arthroplasty. Eighty-four patients (85 hips) underwent revision total hip arthroplasty with use of porous tantalum augments between 2000 and 2007 at a single institution and were retrospectively reviewed. Fifty-seven of the patients (58 hips) had clinical and radiographic follow-up at a minimum of 5 years. At the time of revision, the majority of the hips had acetabular defects classified as Paprosky Type 3A (28 of 58, 48%) or Type 3B (22 of 58, 38%). Eleven (19%) of the hips also had preoperative pelvic discontinuity. All hips were assessed clinically at a minimum of 5 years with use of the Mayo hip score. Postoperative radiographs were reviewed for implant stability, the presence and location of radiolucent lines and healing of the discontinuity if present. In 2 (3%) of the 58 hips, the constructs failed because of aseptic loosening of the acetabular component and re-revision was indicated. Six (10%) of the 58 hips demonstrated a radiolucent line between the trabecular metal shell and bone in DeLee and Charnley zone 3. In 1 hip that underwent re-revision and in 5 of the 6 hips with a zone-3 radiolucency, a pelvic discontinuity was present at the time of the index revision. The mean preoperative Mayo hip score was 35.7, which improved to 61.9 at 3 months and was 61.7 at the minimum 5-year follow-up. With failure defined as aseptic loosening requiring repeat revision surgery, this cohort demonstrated 97% survivorship and maintained satisfactory hip function at the minimum 5 years after the index

  12. Alternative medicine: an update on cupping therapy.

    Science.gov (United States)

    Chen, B; Li, M-Y; Liu, P-D; Guo, Y; Chen, Z-L

    2015-07-01

    To know the research progress of cupping therapy all over the world, the authors analyze the research of cupping therapy in recent 5 years. It indicates that cupping therapy can be applied to extensive curable disease, but has poor clinical evidence. Some improvements in the mechanism research of cupping therapy have been made, but it needs further research. The adverse events of cupping therapy attract attention. The standardization of cupping therapy has emerged. © The Author 2014. Published by Oxford University Press on behalf of the Association of Physicians. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  13. [Mid-Term to Long-Term Results of Revision Total Hip Arthroplasty Using the Oval-Shaped Acetabular Cup - TC Type].

    Science.gov (United States)

    Šťastný, E; Trč, T; Frýdl, J; Kopečný, Z; Philippou, T; Lisý, J

    2017-01-01

    INTRODUCTION The purpose of our paper is to evaluate the mid-term to long-term results and to confirm the basic criteria of a high-quality revision implant: safe bridging of bone defects, achievement of reliable primary fixation of revision acetabular cup, achievement of good secondary stability with documentable osteointegration of cup and demonstration of remodelling of transplanted bone tissue in the area of defects and in spaces between the implant ribs. MATERIAL AND METHODS Altogether 36 patients (38 cups) were evaluated who had undergone revision hip arthroplasty in the period from 2004 to 2010. The mean follow-up was 8.2 years (5.1-11.6 years after the reimplantation, more than 10 years in 16 patients who underwent surgery). The position and osseointegration of the implant were assessed by digital radiography, the remodelling of transplanted bone tissues in the area of defects and between the implant ribs by computed tomography with reducing artefacts around the metal implant (Aquilion 64 - Toshiba Medical Systems), and for the clinical outcomes the Harris Hip Score was used. RESULTS Preoperatively, the condition of the hip joint based on the Harris Hip Score was in 30 cases evaluated as poor, in 8 patients as satisfactory. At the time of final evaluation, 8 patients achieved excellent results, in 19 patients the condition of the joint was very good (in 2 patients bilaterally), in 6 patients it was considered satisfactory and in 3 patients poor. The mean value for HHS increased from 39.5 to 84.5. Based on the radiography evaluation, in 27 patients (in 2 patients bilaterally) the osseointegration of the revision cup was good, in 8 cases with a radiolucent line of 2-4 mm in width in DeLee zone III, in one case proximal migration of the cup occurred caused by deep infection. The informed consent form for pelvic CT was signed by 25 patients of our cohort. Remodelling of bone tissue in the space between the ribs of the implant was always detected, the presence of

  14. Developing and validating a sham cupping device.

    Science.gov (United States)

    Lee, Myeong Soo; Kim, Jong-In; Kong, Jae Cheol; Lee, Dong-Hyo; Shin, Byung-Cheul

    2010-12-01

    The aims of this study were to develop a sham cupping device and to validate its use as a placebo control for healthy volunteers. A sham cupping device was developed by establishing a small hole to reduce the negative pressure after suction such that inner pressure could not be maintained in the cup. We enrolled 34 healthy participants to evaluate the validity of the sham cupping device as a placebo control. The participants were informed that they would receive either real or sham cupping and were asked which treatment they thought they had received. Other sensations and adverse events related to cupping therapy were investigated. 17 patients received real cupping therapy and 17 received sham cupping. The two groups felt similar sensations. There was a tendency for subjects to feel that real cupping created a stronger sensation than sham cupping (48.9±21.4 vs 33.3±20.3 on a 100mm visual analogue scale). There were only mild to moderate adverse events observed in both groups. We developed a new sham cupping device that seems to provide a credible control for real cupping therapy by producing little or no negative pressure. This conclusion was supported by a pilot study, but more rigorous research is warranted regarding the use of this device.

  15. Coffee Cup Atomic Force Microscopy

    Science.gov (United States)

    Ashkenaz, David E.; Hall, W. Paige; Haynes, Christy L.; Hicks, Erin M.; McFarland, Adam D.; Sherry, Leif J.; Stuart, Douglas A.; Wheeler, Korin E.; Yonzon, Chanda R.; Zhao, Jing; Godwin, Hilary A.; Van Duyne, Richard P.

    2010-01-01

    In this activity, students use a model created from a coffee cup or cardstock cutout to explore the working principle of an atomic force microscope (AFM). Students manipulate a model of an AFM, using it to examine various objects to retrieve topographic data and then graph and interpret results. The students observe that movement of the AFM…

  16. A digital model of trabecular bone.

    Science.gov (United States)

    Engelke, K; Song, S M; Glüer, C C; Genant, H K

    1996-04-01

    A 3D microCT dataset of bovine bone was used to create a digital 3D model simulating trabecular bone. The model serves a dual purpose: It allows for standard quantitative histomorphometric analysis and it approximates the reality e.g. of high resolution CT in vivo datasets of trabecular bone. Thus the model can potentially be used as a reference to develop 2D and 3D structural analysis algorithms applicable in vivo while it simultaneously allows verification of the results of these algorithms by standard histomorphometry. The model can be used as a standard to evaluate the impact of image processing techniques and of restrictions of imaging systems on the quantitative analysis of structural parameters describing a trabecular network. The model can be used for a comparison of 2D and 3D structural analysis methods and for an analysis of decreasing spatial resolution. The effects of segmentation and filtration can be studied separately and grayscale analysis is possible. As examples standard 2D histomorphometry and the analysis of topological parameters like node number and trabecular network length were applied to the model. The influence of spatial resolution was investigated by decreasing the spatial resolution of the digital model. The bone surface area determined by 3D surface triangulation was only 4% smaller than the surface area determined from the traditional 2D bone histomorphometric parameter bone surface/tissue volume (BS/TV) when 2D results were averaged over all slices of the 3D volume. However, BS/TV showed large (10%) variations among slices within the volume. Both histomorphometric and topological parameters were heavily influenced by spatial resolution and image segmentation. Our initial experience with the digital model indicates a need to investigate bone microstructure based on volume data or to average the 2D results of many slices.

  17. Hyalinizing trabecular adenoma of the thyroid gland.

    Science.gov (United States)

    Bishop, Justin A; Ali, Syed Z

    2011-04-01

    Hyalinizing trabecular adenoma (HTA) is a rare primary thyroid neoplasm. Ever since its initial descriptions, controversy has surrounded the lesion, particularly in regard to its malignant potential and most appropriate terminology. HTA shares many features with medullary thyroid carcinoma and particularly papillary thyroid carcinoma, making it an especially treacherous lesion on fine-needle aspiration (FNA). This manuscript reviews the history and pathologic features of HTA, with particular attention to cytologic findings and differential diagnosis. Copyright © 2010 Wiley-Liss, Inc.

  18. Cupping for Treating Pain: A Systematic Review

    Directory of Open Access Journals (Sweden)

    Jong-In Kim

    2011-01-01

    Full Text Available The objective of this study was to assess the evidence for or against the effectiveness of cupping as a treatment option for pain. Fourteen databases were searched. Randomized clinical trials (RCTs testing cupping in patients with pain of any origin were considered. Trials using cupping with or without drawing blood were included, while trials comparing cupping with other treatments of unproven efficacy were excluded. Trials with cupping as concomitant treatment together with other treatments of unproven efficacy were excluded. Trials were also excluded if pain was not a central symptom of the condition. The selection of studies, data extraction and validation were performed independently by three reviewers. Seven RCTs met all the inclusion criteria. Two RCTs suggested significant pain reduction for cupping in low back pain compared with usual care (P < .01 and analgesia (P < .001. Another two RCTs also showed positive effects of cupping in cancer pain (P < .05 and trigeminal neuralgia (P < .01 compared with anticancer drugs and analgesics, respectively. Two RCTs reported favorable effects of cupping on pain in brachialgia compared with usual care (P = .03 or heat pad (P < .001. The other RCT failed to show superior effects of cupping on pain in herpes zoster compared with anti-viral medication (P = .065. Currently there are few RCTs testing the effectiveness of cupping in the management of pain. Most of the existing trials are of poor quality. Therefore, more rigorous studies are required before the effectiveness of cupping for the treatment of pain can be determined.

  19. Faraday Cup - it is used to measure beam intensities at low energy beams.

    CERN Multimedia

    Maximilien Brice

    2005-01-01

    A Faraday Cup is used to measure beam intensities at low energy beams. An electrically isolated metallic electrode intercepts the beam and captures all its charges. These charges are integrated using an current sensitive amplifier. When the beam impinges onto the electrode surface low energy electrons are liberated. In order to prevent these electrons from escaping the cup and thus falsifying the measurement, a repeller electrode with negative potential pushes the electrons back onto the electrode.

  20. Effects of hydroxyapatite coating of cups used in hip revision arthroplasty

    Science.gov (United States)

    2012-01-01

    Background and purpose Coating of acetabular revision implants with hydroxyapatite (HA) has been proposed to improve ingrowth and stability. We investigated whether HA coating of revision cups can reduce the risk of any subsequent re-revision. Methods We studied uncemented cups either with or without HA coating that were used at a primary acetabular revision and registered in the Swedish Hip Arthroplasty Register (SHAR). 2 such cup designs were identified: Harris-Galante and Trilogy, both available either with or without HA coating. These cups had been used as revision components in 1,780 revisions of total hip arthroplasties (THA) between 1986 and 2009. A Cox proportional hazards model including the type of coating, age at index revision, sex, cause of cup revision, cup design, the use of bone graft at the revision procedure, and the type of cup fixation at primary THA were used to calculate adjusted risk ratios (RRs with 95% CI) for re-revision for any reason or due to aseptic loosening. Results 71% of the cups were coated with HA and 29% were uncoated. At a mean follow-up time of 6.9 (0–24) years, 159 (9%) of all 1,780 cups had been re-revised, mostly due to aseptic loosening (5%), dislocation (2%), or deep infection (1%). HA coating had no significant influence on the risk of re-revision of the cup for any reason (RR = 1.4, CI: 0.9–2.0) or due to aseptic loosening (RR = 1.1, 0.6–1.9). In contrast, HA coating was found to be a risk factor for isolated liner re-revision for any reason (RR = 1.8, CI: 1.01–3.3). Age below 60 years at the index cup revision, dislocation as the cause of the index cup revision, uncemented cup fixation at primary THA, and use of the Harris-Galante cup also increased the risk of re-revision of the cup. In separate analyses in which isolated liner revisions were excluded, bone grafting was found to be a risk factor for re-revision of the metal shell due to aseptic loosening (RR = 2.1, CI: 1.05–4.2). Interpretation We found no

  1. Factitious panniculitis induced by cupping therapy.

    Science.gov (United States)

    Moon, Suk-Ho; Han, Hyun-Ho; Rhie, Jong-Won

    2011-11-01

    Cupping therapy is an alternative medical procedure that has been widely performed in Asian countries to relieve pain. It is known that there is no complication to this therapy, so many non-health care professionals have performed this procedure. However, there have been few reports on complications, such as iron deficiency anemia, hemorrhagic bullae, kelloids, vasovagal syncope, and foreign body reactions. Masses associated with panniculitis induced by cupping are extremely rare, and they require a unique approach.A 56-year-old woman presented with a 10-month history of multiple masses in the posterior neck and right shoulder areas. The patient repeatedly attempted cupping therapy by herself, and multiple palpable masses developed in the posterior neck and right shoulder area where cupping therapy had been performed. The masses were enlarged by repeated cupping, and they decreased in size when cupping was stopped. Among all lesions, the 2 masses with tenderness were surgically excised. The remaining masses resolved after cupping therapy was ceased. When a patient with subcutaneous mass has a history of cupping or trace of cupping marks, panniculitis induced by cupping should be suspected. The lesion seems to spontaneously resolve unless they are repeatedly stimulated. However, surgical resection is considered in patients with infections or severe tenderness as a complication.

  2. Trabecular network arrangement within the human patella: how osteoarthritis remodels the 3D trabecular structure

    Science.gov (United States)

    Hoechel, Sebastian; Deyhle, Hans; Toranelli, Mireille; Müller-Gerbl, Magdalena

    2016-10-01

    Following the principles of "morphology reveals biomechanics", the anatomical structure of the cartilage-osseous interface and the supporting trabecular network show defined adaptation in their architectural properties to physiological loading. In case of a faulty relationship, the ability to support the load diminishes and the onset of osteoarthritis (OA) may arise and disturb the balanced formation and resorption processes. To describe and quantify the changes occurring, 10 human OA patellae were analysed concerning the architectural parameters of the trabecular network within the first five mms by the evaluation of 3Dmicro-CT datasets. The analysed OA-samples showed a strong irregularity for all trabecular parameters across the trabecular network, no regularity in parameter distribution was found. In general, we saw a decrease of material in the OA population as BV/TV, BS/TV, Tb.N and Tb.Th were decreased and the spacing increased. The development into depth showed a logarithmic dependency, which revealed the greatest difference for all parameters within the first mm in comparison to the physiologic samples. The differences decreased towards the 5th mm. The interpretation of the mathematic dependency leads to the conclusion that the main impact of OA is beneath the subchondral bone plate (SBP) and lessens with depth. Next to the clear difference in material, the architectural arrangement is more rod-like and isotropic just beneath the SBP in comparison to the plate-like and more anisotropic physiological arrangement.

  3. New alkali metal diphosphates how materials to preserve the security of the environment: CsNaCu(P2O7), Rb2Cu(P2O7) and CsNaCo(P2O7) synthesis and crystal structure determination

    Science.gov (United States)

    Chernyatieva, Anastasiya; Filatova, Alyona; Spiridonova, Dariya; Krivovichev, Sergey

    2013-04-01

    In this work we describe preliminary results of the synthesis and of a crystal-chemical study of synthetic phosphates with transition metals. Due to the increasing requirements for environmental safety specialists from various industries, we are searching for sustainable forms of immobilization of hazardous waste during storage. We are also developing a component-based waste for new materials. In our continued exploratory synthesis of compounds containing transition-metals, we were able to produce the new diphosphate phases CsNaCu(P2O7), Rb2Cu(P2O7) and CsNaCo(P2O7). A crystal chemical study has allowed us to identify new phosphates. Crystals of CsNaCu(P2O7) (Phase 1) is orthorhombic, crystallizes in space group Pmn21, with a = 5.147(8), b = 15.126(2), c = 9.717(2) Å, V = 756.20 Å3, R1 = 0.066 and Rb2Cu(P2O7) (Phase 2) is orthorhombic as well, crystallizes in space group Pmcn, with a = 5.183(8), b = 10.096(1), c = 15.146(3) Å, V = 793.55 Å3, R1 = 0.063, they have been obtained by high-temperature reaction of RbNO3, CsNO3, Cu(NO3)2, NaOH and (NH4)4P2O7. Synthetic crystals of the phosphate of copper and rubidium were studied in detail by us on the structures of Rb2Cu(P2O7) and Rb2Cu3(P2O7)2 - new alkali metal copper diphosphates (CHERNYATIEVA et al., 2008). Here we report the synthesis, the structure and the properties of the title compounds and we compare these phases with the previously discovered K2CuP2O7 (ELMAADI et al., 1995) and CsNaMnP2O7 (HUANG et al., 1998). These structures crystallize in other space groups, although their structures are also based on 2-D layers, formed by P2O7 groups combined with polyhedra of the transition metals (CHERNYATIEVA et al., 2012). A crystal chemical study has allowed us to identify even new diphosphates CsNaCu(P2O7) (Phase 3). Crystals of CsNaCoP2O7 is monoclinic, space group P 21/n, with a = 7,424(2), b = 7,648(1), c = 12,931(3)Å, β = 90,71(2)° , V = 734.2(3) Å3 and R1 = 0.060. The structure is based framework of Co

  4. A New High-Temperature Oscillating Cup Viscometer

    Science.gov (United States)

    Kehr, M.; Hoyer, W.; Egry, I.

    2007-06-01

    A new oscillating cup viscometer for temperatures up to 2,300°C has been constructed. A vacuum furnace with a graphite heater is used for heating the sample. The temperatures of the furnace and sample are measured by both a thermocouple and a pyrometer. The temperature is controlled with a stability better than 1 K. The oscillation of the cup is measured with a reflected laser beam using a position sensitive detector. The measured values of angle and time are then fitted to an analytical oscillation function. From the parameters of this function, the viscosity values are calculated using the Roscoe formalism. Measurements were carried out on pure metals at temperatures up to 1,700°C because of limitations of the thermocouple. The obtained viscosity values showed good agreement with literature data.

  5. Field calibration of cup anemometers

    DEFF Research Database (Denmark)

    Kristensen, L.; Jensen, G.; Hansen, A.

    2001-01-01

    An outdoor calibration facility for cup anemometers, where the signals from 10 anemometers of which at least one is a reference can be can be recorded simultaneously, has been established. The results are discussed with special emphasis on the statisticalsignificance of the calibration expressions....... It is concluded that the method has the advantage that many anemometers can be calibrated accurately with a minimum of work and cost. The obvious disadvantage is that the calibration of a set of anemometersmay take more than one month in order to have wind speeds covering a sufficiently large magnitude range...

  6. Trabecular architecture analysis in femur radiographic images using fractals.

    Science.gov (United States)

    Udhayakumar, G; Sujatha, C M; Ramakrishnan, S

    2013-04-01

    Trabecular bone is a highly complex anisotropic material that exhibits varying magnitudes of strength in compression and tension. Analysis of the trabecular architectural alteration that manifest as loss of trabecular plates and connection has been shown to yield better estimation of bone strength. In this work, an attempt has been made toward the development of an automated system for investigation of trabecular femur bone architecture using fractal analysis. Conventional radiographic femur bone images recorded using standard protocols are used in this study. The compressive and tensile regions in the images are delineated using preprocessing procedures. The delineated images are analyzed using Higuchi's fractal method to quantify pattern heterogeneity and anisotropy of trabecular bone structure. The results show that the extracted fractal features are distinct for compressive and tensile regions of normal and abnormal human femur bone. As the strength of the bone depends on architectural variation in addition to bone mass, this study seems to be clinically useful.

  7. Mucopolysaccharides in the trabecular meshwork. Light and electron microscopic autoradiography

    Energy Technology Data Exchange (ETDEWEB)

    Ohnishi, Yoshitaka; Yamana, Yasuo; Abe, Masahiro (Kyushu Univ., Fukuoka (Japan). Faculty of Medicine)

    1982-09-01

    The localization of /sup 35/S-sulfate and /sup 3/H-glucosamine in the trabecular region of the hamster was studied by light and electron microscopic autoradiography after the intraperitoneal injection. Exposed silver grains of /sup 35/S-sulfate were concentrated in the trabecular meshwork, sclera and cornea, and grains of /sup 35/H-glucosamine were localized in the trabecular region. The radioactivity of both isotopes was observed in the Golgi apparatuses of the endothelial cells and fibroblasts in Schlemm's canal and the trabecular meshwork. Thereafter, the grains were noted over the entire cytoplasm, except for the nucleus, and then were incorporated into the amorphous substance and collagen fibers in the juxtacanalicular connective tissue. These results suggest that endothelial cells in the trabecular region synthesize and secrete the sulfated mucopolysaccharides and hyaluronic acid.

  8. 21 CFR 884.5400 - Menstrual cup.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Menstrual cup. 884.5400 Section 884.5400 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES OBSTETRICAL AND GYNECOLOGICAL DEVICES Obstetrical and Gynecological Therapeutic Devices § 884.5400 Menstrual cup. (a) Identification. A menstrual...

  9. Soccer jersey sponsors and the world cup

    NARCIS (Netherlands)

    Groot, L.F.M.; Ferwerda, J.

    2014-01-01

    The market for soccer jerseys is a multibillion market dominated by Adidas, Nike and Puma. This paper investigates whether jersey sponsorship has a non-arbitrary effect on the outcomes of World Cup knockout matches. The results show that in the knockout stages of the last four World Cup tournaments,

  10. Sound analysis of a cup drum

    International Nuclear Information System (INIS)

    Kim, Kun ho

    2012-01-01

    The International Young Physicists’ Tournament (IYPT) is a worldwide tournament that evaluates a high-school student's ability to solve various physics conundrums that have not been fully resolved in the past. The research presented here is my solution to the cup drum problem. The physics behind a cup drum has never been explored or modelled. A cup drum is a musical instrument that can generate different frequencies and amplitudes depending on the location of a cup held upside-down over, on or under a water surface. The tapping sound of a cup drum can be divided into two components: standing waves and plate vibration. By individually researching the nature of these two sounds, I arrived at conclusions that could accurately predict the frequencies in most cases. When the drum is very close to the surface, qualitative explanations are given. In addition, I examined the trend of the tapping sound amplitude at various distances and qualitatively explained the experimental results. (paper)

  11. Heme compounds in dinosaur trabecular bone.

    Science.gov (United States)

    Schweitzer, M H; Marshall, M; Carron, K; Bohle, D S; Busse, S C; Arnold, E V; Barnard, D; Horner, J R; Starkey, J R

    1997-06-10

    Six independent lines of evidence point to the existence of heme-containing compounds and/or hemoglobin breakdown products in extracts of trabecular tissues of the large theropod dinosaur Tyrannosaurus rex. These include signatures from nuclear magnetic resonance and electron spin resonance that indicate the presence of a paramagnetic compound consistent with heme. In addition, UV/visible spectroscopy and high performance liquid chromatography data are consistent with the Soret absorbance characteristic of this molecule. Resonance Raman profiles are also consistent with a modified heme structure. Finally, when dinosaurian tissues were extracted for protein fragments and were used to immunize rats, the resulting antisera reacted positively with purified avian and mammalian hemoglobins. The most parsimonious explanation of this evidence is the presence of blood-derived hemoglobin compounds preserved in the dinosaurian tissues.

  12. Fourier analysis of the aerodynamic behavior of cup anemometers

    International Nuclear Information System (INIS)

    Pindado, Santiago; Pérez, Imanol; Aguado, Maite

    2013-01-01

    The calibration results (the transfer function) of an anemometer equipped with several cup rotors were analyzed and correlated with the aerodynamic forces measured on the isolated cups in a wind tunnel. The correlation was based on a Fourier analysis of the normal-to-the-cup aerodynamic force. Three different cup shapes were studied: typical conical cups, elliptical cups and porous cups (conical-truncated shape). Results indicated a good correlation between the anemometer factor, K, and the ratio between the first two coefficients in the Fourier series decomposition of the normal-to-the-cup aerodynamic force. (paper)

  13. Age variations in the properties of human tibial trabecular bone

    DEFF Research Database (Denmark)

    Ding, Ming; Dalstra, M; Danielsen, CC

    1997-01-01

    We tested in compression specimens of human proximal tibial trabecular bone from 31 normal donors aged from 16 to 83 years and determined the mechanical properties, density and mineral and collagen content. Young's modulus and ultimate stress were highest between 40 and 50 years, whereas ultimate...... amount of collagen) varied with failure energy. Collagen concentration was maximal at younger ages but varied little with age. Our results suggest that the decrease in mechanical properties of trabecular bone such as Young's modulus and ultimate stress is mainly a consequence of the loss of trabecular...

  14. A radioactive football world cup

    International Nuclear Information System (INIS)

    Sorin, F.

    2014-01-01

    The organization of the 2014 football world cup by Brazil is an opportunity to recall how the level of natural radioactivity can change from a country to another. Brazil is with Iran and India one of the 3 countries where the level of natural radioactivity is the highest. In Brazil the average value for natural radioactivity is about 10 mSv/year but you can find spots on the Brazilian 'planalto' where natural radioactivity ranges from 10 to a few tens of mSv/year. The mean value of natural radioactivity at the world scale is about 2.5 mSv/year. The value of 10 mSv/year is the radiation threshold that may trigger the evacuation of the local population in case of a nuclear accident in France. These various figures show that radiation dose limits are very low and should not be considered as representative of actual health hazards. (A.C.)

  15. Rationale for the evaluation of trabecular bone turnover

    International Nuclear Information System (INIS)

    Kimmel, D.B.; Jee, W.S.S.

    1976-01-01

    A procedure for the morphometric evaluation of trabecular bone is identified. Its scrupulous use allows total identification of bone formation and resorption rates, items necessary for the direct histologic analysis of bone turnover

  16. Regional cortical and trabecular bone loss after spinal cord injury

    OpenAIRE

    Dudley-Javoroski, Shauna; Shields, Richard K.

    2012-01-01

    Spinal cord injury (SCI) triggers rapid loss of trabecular bone mineral density (BMD) in bone epiphyses and a loss of cortical cross-sectional area (CSA) in bone diaphyses, increasing fracture risk for people with SCI. The purpose of this study was to measure trabecular BMD and cortical CSA loss at several previously unexamined lower-limb sites (4% fibula, 12% femur, 86% tibia, cortical) in individuals with SCI. Using peripheral quantitative computed tomography, we scanned 13 participants wit...

  17. Radiological diagnostics in CUP syndrome

    International Nuclear Information System (INIS)

    Kazmierczak, P.M.; Nikolaou, K.; Graser, A.; Reiser, M.F.; Cyran, C.C.; Rominger, A.

    2014-01-01

    Imaging plays an essential role in the therapeutic management of cancer of unknown primary (CUP) patients for localizing the primary tumor, for the identification of tumor entities for which a dedicated therapy regimen is available and for the characterization of clinicopathological subentities that direct the subsequent diagnostic and therapeutic strategy. Modalities include conventional x-ray, computed tomography (CT), magnetic resonance imaging (MRI) and ultrasound as well as positron emission tomography (PET)-CT and MRI-PET. In whole body imaging CT has a high sensitivity for tumor entities which frequently present as a metastasized cancer illness. According to the current literature CT is diagnostic in 86% of patients with pancreatic carcinoma, in 36% of patients with colon carcinoma and in 74% of patients with lung carcinoma. Additionally a meta-analysis showed that for patients with squamous cell carcinoma and cervical lymph node metastases a positive diagnosis was possible in 22% of the cases using CT, in 36% using MRI and in 28-57% using 18F-fluorodeoxyglucose PET-CT ( 18 F-FDG PET-CT). In addition, MRI plays an important role in the localization of primary occult tumors (e.g. breast and prostate) because of its high soft tissue contrast and options for functional imaging. At the beginning of the diagnostic algorithm stands the search for a possible primary tumor and CT of the neck, thorax and abdomen is most frequently used for whole body staging. Subsequent organ-specific imaging examinations follow, e.g. mammography in women with axillary lymphadenopathy. For histological and immunohistochemical characterization of tumor tissue, imaging is also applied to identify the most accessible and representative tumor manifestation for biopsy. Tumor biopsy may be guided by CT, MRI or ultrasound and MRI also plays a central role in the localization of primary occult tumors because of superior soft tissue contrast and options for functional imaging (perfusion

  18. Recent origin of low trabecular bone density in modern humans

    Science.gov (United States)

    Chirchir, Habiba; Kivell, Tracy L.; Ruff, Christopher B.; Hublin, Jean-Jacques; Carlson, Kristian J.; Zipfel, Bernhard; Richmond, Brian G.

    2015-01-01

    Humans are unique, compared with our closest living relatives (chimpanzees) and early fossil hominins, in having an enlarged body size and lower limb joint surfaces in combination with a relatively gracile skeleton (i.e., lower bone mass for our body size). Some analyses have observed that in at least a few anatomical regions modern humans today appear to have relatively low trabecular density, but little is known about how that density varies throughout the human skeleton and across species or how and when the present trabecular patterns emerged over the course of human evolution. Here, we test the hypotheses that (i) recent modern humans have low trabecular density throughout the upper and lower limbs compared with other primate taxa and (ii) the reduction in trabecular density first occurred in early Homo erectus, consistent with the shift toward a modern human locomotor anatomy, or more recently in concert with diaphyseal gracilization in Holocene humans. We used peripheral quantitative CT and microtomography to measure trabecular bone of limb epiphyses (long bone articular ends) in modern humans and chimpanzees and in fossil hominins attributed to Australopithecus africanus, Paranthropus robustus/early Homo from Swartkrans, Homo neanderthalensis, and early Homo sapiens. Results show that only recent modern humans have low trabecular density throughout the limb joints. Extinct hominins, including pre-Holocene Homo sapiens, retain the high levels seen in nonhuman primates. Thus, the low trabecular density of the recent modern human skeleton evolved late in our evolutionary history, potentially resulting from increased sedentism and reliance on technological and cultural innovations. PMID:25535354

  19. Trabecular organization in mandibular osteodistraction in growing and maturing rats.

    Science.gov (United States)

    Shin, Ja Young; Liu, Zi Jun; King, Gregory Joseph

    2005-01-01

    Our goal was to investigate the trabecular organization of the distraction regenerate during various consolidation phases and as a result of various distraction rates. One hundred ninety-two growing and maturing rats (96 each) received unilateral mandibular osteotomies and distraction device placement. They were randomly allocated into 4 distraction rate groups (0, 0.2, 0.4, and 0.6 mm/day for 5 days) after a 3-day latency. Eight rats from each rate group were sacrificed at early (10 days), mid (24 days) and late (38 days) consolidation time points. Harvested hemimandibles were embedded in micro-bed resin, sectioned sagittally at 10 mum thickness and stained using the Von Kossa method. The histologic images were captured and processed using Adobe Photoshop (Version 7.0; Adobe Systems Inc, San Jose, CA). Custom-made software (MacAzimuth; written by Prof. J.M. Rensberger, University of Washington) was further used to analyze the orientation (anisotropy and angle distribution) and mass (density and thickness) of trabecular structures in the regenerates. Trabecular orientation significantly differed at the mid-consolidation time point with less anisotropy ( P consolidation ( P time points ( P bone mineral density and microdensity ( P consolidation with a greater increase in trabecular mass. Growing rats showed a greater capacity for trabecular organization at earlier time points. However, distraction rate did not have an effect on trabecular organization. These results suggest that trabecular organization can be used as an important indicator to evaluate bone maturation and quality in the distraction regenerate.

  20. From Baby Bottle to Cup: Choose Training Cups Carefully, Use Them Temporarily

    Science.gov (United States)

    ... production increases during a meal and helps neutralize acid production and rinse food particles from the mouth.) If your child is thirsty between meals, offer water in the cup. Do not let your child carry the training cup around, or get into the habit of ...

  1. Mechanical properties of femoral trabecular bone in dogs

    Directory of Open Access Journals (Sweden)

    Nolte Ingo

    2005-03-01

    Full Text Available Abstract Background Studying mechanical properties of canine trabecular bone is important for a better understanding of fracture mechanics or bone disorders and is also needed for numerical simulation of canine femora. No detailed data about elastic moduli and degrees of anisotropy of canine femoral trabecular bone has been published so far, hence the purpose of this study was to measure the elastic modulus of trabecular bone in canine femoral heads by ultrasound testing and to assess whether assuming isotropy of the cancellous bone in femoral heads in dogs is a valid simplification. Methods From 8 euthanized dogs, both femora were obtained and cubic specimens were cut from the centre of the femoral head which were oriented along the main pressure and tension trajectories. The specimens were tested using a 100 MHz ultrasound transducer in all three orthogonal directions. The directional elastic moduli of trabecular bone tissue and degrees of anisotropy were calculated. Results The elastic modulus along principal bone trajectories was found to be 11.2 GPa ± 0.4, 10.5 ± 2.1 GPa and 10.5 ± 1.8 GPa, respectively. The mean density of the specimens was 1.40 ± 0.09 g/cm3. The degrees of anisotropy revealed a significant inverse relationship with specimen densities. No significant differences were found between the elastic moduli in x, y and z directions, suggesting an effective isotropy of trabecular bone tissue in canine femoral heads. Discussion This study presents detailed data about elastic moduli of trabecular bone tissue obtained from canine femoral heads. Limitations of the study are the relatively small number of animals investigated and the measurement of whole specimen densities instead of trabecular bone densities which might lead to an underestimation of Young's moduli. Publications on elastic moduli of trabecular bone tissue present results that are similar to our data. Conclusion This study provides data about directional elastic

  2. FRACTAL ANALYSIS OF TRABECULAR BONE: A STANDARDISED METHODOLOGY

    Directory of Open Access Journals (Sweden)

    Ian Parkinson

    2011-05-01

    Full Text Available A standardised methodology for the fractal analysis of histological sections of trabecular bone has been established. A modified box counting method has been developed for use on a PC based image analyser (Quantimet 500MC, Leica Cambridge. The effect of image analyser settings, magnification, image orientation and threshold levels, was determined. Also, the range of scale over which trabecular bone is effectively fractal was determined and a method formulated to objectively calculate more than one fractal dimension from the modified Richardson plot. The results show that magnification, image orientation and threshold settings have little effect on the estimate of fractal dimension. Trabecular bone has a lower limit below which it is not fractal (λ<25 μm and the upper limit is 4250 μm. There are three distinct fractal dimensions for trabecular bone (sectional fractals, with magnitudes greater than 1.0 and less than 2.0. It has been shown that trabecular bone is effectively fractal over a defined range of scale. Also, within this range, there is more than 1 fractal dimension, describing spatial structural entities. Fractal analysis is a model independent method for describing a complex multifaceted structure, which can be adapted for the study of other biological systems. This may be at the cell, tissue or organ level and compliments conventional histomorphometric and stereological techniques.

  3. Influence of cortical endplates on ultrasonic properties of trabecular bone

    International Nuclear Information System (INIS)

    Kim, Yoon Mi; Lee, Kang Il

    2015-01-01

    The present study investigated the influence of thick cortical endplates on the ultrasonic properties of trabecular bone in a femur with a high fracture risk. Twelve trabecular bone samples were prepared from bovine femurs, and acrylic plates with thicknesses of 1.25, 1.80, and 2.75 mm were manufactured to simulate the cortical endplates using acrylic with a density and a sound speed similar to cortical bone. Although the thickness of the acrylic plates attached to the two sides of the trabecular bone increased, high correlations were observed between the speed of sound and the apparent bone density of the trabecular bone, with Pearson's correlation coefficients of 0.80-0.86. High correlations were also observed between the attenuation coefficient at 0.5 mm and the apparent bone density of the trabecular bone, with Pearson's correlation coefficients of 0.84-0.91. These results suggest that the speed of sound and attenuation coefficient at a specific frequency measured in a femur with relatively thick cortical endplates compared to the calcaneus could be used as indices for predicting the bone mineral density of the femur.

  4. Influence of cortical endplates on ultrasonic properties of trabecular bone

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yoon Mi; Lee, Kang Il [Dept. of Physics, Kangwon National University, Chuncheon (Korea, Republic of)

    2015-04-15

    The present study investigated the influence of thick cortical endplates on the ultrasonic properties of trabecular bone in a femur with a high fracture risk. Twelve trabecular bone samples were prepared from bovine femurs, and acrylic plates with thicknesses of 1.25, 1.80, and 2.75 mm were manufactured to simulate the cortical endplates using acrylic with a density and a sound speed similar to cortical bone. Although the thickness of the acrylic plates attached to the two sides of the trabecular bone increased, high correlations were observed between the speed of sound and the apparent bone density of the trabecular bone, with Pearson's correlation coefficients of 0.80-0.86. High correlations were also observed between the attenuation coefficient at 0.5 mm and the apparent bone density of the trabecular bone, with Pearson's correlation coefficients of 0.84-0.91. These results suggest that the speed of sound and attenuation coefficient at a specific frequency measured in a femur with relatively thick cortical endplates compared to the calcaneus could be used as indices for predicting the bone mineral density of the femur.

  5. Safety of cupping during bevacizumab therapy.

    Science.gov (United States)

    Klempner, Samuel J; Costa, Daniel B; Wu, Peggy A; Ariyabuddhiphongs, Kim D

    2013-08-01

    This study reports on the safety of the complementary and alternative medicine (CAM) practice of cupping in a patient undergoing concomitant therapy with bevacizumab for advanced non-small-cell lung cancer (NSCLC), and raises awareness of the need for improved communication between CAM practitioners and oncologists during the care of patients with cancer. The practice of cupping generates local hyperemia, disrupts superficial vasculature in the dermis, and leads to cutaneous lesions including circular erythema, edema, and subsequently ecchymosis. There are no data on the safety of cupping in patients being treated with bevacizumab. This is a single-institution case report. The setting for this study was a tertiary-care academic medical center. A patient with advanced NSCLC received four cycles of carboplatin AUC 6, paclitaxel 200 mg/m(2), and bevacizumab 15 mg/kg, and was continued on every-3-week maintenance bevacizumab 15 mg/kg. The patient underwent glass dry cupping during cycle six of maintenance bevacizumab treatment without overt cutaneous adverse events or bleeding. The patient did not realize he should have communicated his cupping plans or recent bevacizumab treatment with his providers.

  6. Design of the Faraday Cups in Diamond

    CERN Document Server

    Morgan, A F D

    2005-01-01

    This paper details the work done on the design of the Faraday cups for the Diamond injector. Faraday cups are a basic charge capture device which can be used as reference points for current measurement calibration. Diamond has Faraday cups in positions covering the complete energy range of the injector from the electron gun to the booster synchrotron extraction. Specifically there are cups at 90 keV, 4 MeV, 100 MeV and 3 GeV. An initial design decision was made to make the designs passive to increase reliability and reduce complexity. The 90 keV and 4 MeV cups were modified from an existing design using analytical formulae and MathCAD, while the high energy 100 MeV and 3 GeV designs were done using the EGSnrc Monte Carlo code and MatLAB. The EGSnrc led designs achieved a theoretical electron capture of around 99%, allowing them to be used with reasonable certainty as calibration references. Due to the modest 5Hz repetition rate, power loading of the structures is minimal and active cooling is not required for...

  7. Dependences of ultrasonic properties on the propagation angle with respect to the trabecular alignment in trabecular bone

    International Nuclear Information System (INIS)

    Lee, Kang Il

    2014-01-01

    The present study aims to investigate the dependences of ultrasonic properties on the propagation angle with respect to the trabecular alignment in 12 bovine femoral trabecular bone samples. The phase velocity and the attenuation coefficient of the fast wave measured at 0.5 MHz were found to decrease significantly with increasing angle and had their maximum values at 0 .deg. , i.e., for wave propagation in a direction parallel to the predominant trabecular alignment. The present study applied the angle-dependent Biot model by introducing anisotropy into the Biot model through the angle-dependent Young's, bulk, and shear moduli of the skeletal frame for trabecular bone to predict the measurements. Good agreement between the measurements and the prediction of the fast wave velocity suggests that the anisotropic fast wave velocity as a function of the propagation angle is mainly due to the variation in the elastic moduli of the skeletal frame with respect to the trabecular alignment.

  8. Trabecular bone structure and strength - remodelling and repair

    DEFF Research Database (Denmark)

    Mosekilde, Lis; Ebbesen, Ebbe Nils; Erikstrup, Lise Tornvig

    2000-01-01

    by the remodelling process. 5) Bone material quality will slightly change, leading to a decrease in collagen content and a relative increase in the degree of mineralisation. But, it is not known how these factors will influence the power relationship between density and strength. Nor is it known how different......The strength of the spinal trabecular bone declines by a factor of 4-5 from the age of 20 to 80 years. At the same time, the volumetric (apparent) density declines by a factor of only 2. This discrepancy can be explained by the known power relationship between density and strength; this power...... relationship is based on the fact that trabecular bone is a porous material. To date, it has not been possible to determine or quantify the influence other factors may have in determining the strength of a loadbearing trabecular network. However, it is known that with age: 1) There is a loss of connectivity...

  9. Nuclear fuel element nut retainer cup

    International Nuclear Information System (INIS)

    Walton, L.A.

    1977-01-01

    A typical embodiment has an end fitting for a nuclear reactor fuel element that is joined to the control rod guide tubes by means of a nut plate assembly. The nut plate assembly has an array of nuts, each engaging the respective threaded end of the control rod guide tubes. The nuts, moreover, are retained on the plate during handling and before fuel element assembly by means of hollow cylindrical locking cups that are brazed to the plate and loosely circumscribe the individual enclosed nuts. After the nuts are threaded onto the respective guide tube ends, the locking cups are partially deformed to prevent one or more of the nuts from working loose during reactor operation. The locking cups also prevent loose or broken end fitting parts from becoming entrained in the reactor coolant

  10. A topological look at human trabecular bone tissue.

    Science.gov (United States)

    Bini, G; Bini, F; Bedini, R; Marinozzi, A; Marinozzi, F

    2017-06-01

    Bone quality is affected by trabecular architecture at microscopic level. Various abnormalities of bone tissue lead to altered strength and to an increased susceptibility to fracture, such as Osteoporosis and Osteoarthritis, two major health burdens of our society. These are two complex musculoskeletal diseases that mainly concern bone tissue. In the last twenty years, there has been a growing interest in finding an appropriate topological model for the micro-architecture of trabecular bone tissue. In particular, we prove that these models involve general topological spaces. The appropriate notion to deal with is that of CW-complex. Copyright © 2017 Elsevier Inc. All rights reserved.

  11. An updated review of the efficacy of cupping therapy.

    Directory of Open Access Journals (Sweden)

    Huijuan Cao

    Full Text Available BACKGROUND: Since 1950, traditional Chinese medicine (TCM cupping therapy has been applied as a formal modality in hospitals throughout China and elsewhere in the world. Based on a previous systematic literature review of clinical studies on cupping therapy, this study presents a thorough review of randomized controlled trials (RCTs to evaluate the therapeutic effect of cupping therapy. METHOD: Six databases were searched for articles published through 2010. RCTs on cupping therapy for various diseases were included. Studies on cupping therapy combined with other TCM treatments versus non-TCM therapies were excluded. RESULTS: 135 RCTs published from 1992 through 2010 were identified. The studies were generally of low methodological quality. Diseases for which cupping therapy was commonly applied were herpes zoster, facial paralysis (Bell palsy, cough and dyspnea, acne, lumbar disc herniation, and cervical spondylosis. Wet cupping was used in most trials, followed by retained cupping, moving cupping, and flash cupping. Meta-analysis showed cupping therapy combined with other TCM treatments was significantly superior to other treatments alone in increasing the number of cured patients with herpes zoster, facial paralysis, acne, and cervical spondylosis. No serious adverse effects were reported in the trials. CONCLUSIONS: Numerous RCTs on cupping therapy have been conducted and published during the past decades. This review showed that cupping has potential effect in the treatment of herpes zoster and other specific conditions. However, further rigorously designed trials on its use for other conditions are warranted.

  12. An updated review of the efficacy of cupping therapy.

    Science.gov (United States)

    Cao, Huijuan; Li, Xun; Liu, Jianping

    2012-01-01

    Since 1950, traditional Chinese medicine (TCM) cupping therapy has been applied as a formal modality in hospitals throughout China and elsewhere in the world. Based on a previous systematic literature review of clinical studies on cupping therapy, this study presents a thorough review of randomized controlled trials (RCTs) to evaluate the therapeutic effect of cupping therapy. Six databases were searched for articles published through 2010. RCTs on cupping therapy for various diseases were included. Studies on cupping therapy combined with other TCM treatments versus non-TCM therapies were excluded. 135 RCTs published from 1992 through 2010 were identified. The studies were generally of low methodological quality. Diseases for which cupping therapy was commonly applied were herpes zoster, facial paralysis (Bell palsy), cough and dyspnea, acne, lumbar disc herniation, and cervical spondylosis. Wet cupping was used in most trials, followed by retained cupping, moving cupping, and flash cupping. Meta-analysis showed cupping therapy combined with other TCM treatments was significantly superior to other treatments alone in increasing the number of cured patients with herpes zoster, facial paralysis, acne, and cervical spondylosis. No serious adverse effects were reported in the trials. Numerous RCTs on cupping therapy have been conducted and published during the past decades. This review showed that cupping has potential effect in the treatment of herpes zoster and other specific conditions. However, further rigorously designed trials on its use for other conditions are warranted.

  13. File list: His.Oth.50.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available His.Oth.50.AllAg.Trabecular_meshwork_cells hg19 Histone Others Trabecular meshwork ...cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/His.Oth.50.AllAg.Trabecular_meshwork_cells.bed ...

  14. File list: ALL.Oth.20.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ALL.Oth.20.AllAg.Trabecular_meshwork_cells hg19 All antigens Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/ALL.Oth.20.AllAg.Trabecular_meshwork_cells.bed ...

  15. File list: DNS.Oth.20.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available DNS.Oth.20.AllAg.Trabecular_meshwork_cells hg19 DNase-seq Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/DNS.Oth.20.AllAg.Trabecular_meshwork_cells.bed ...

  16. File list: Pol.Oth.05.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Pol.Oth.05.AllAg.Trabecular_meshwork_cells hg19 RNA polymerase Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Pol.Oth.05.AllAg.Trabecular_meshwork_cells.bed ...

  17. File list: Oth.Oth.05.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Oth.Oth.05.AllAg.Trabecular_meshwork_cells hg19 TFs and others Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Oth.Oth.05.AllAg.Trabecular_meshwork_cells.bed ...

  18. File list: Oth.Oth.50.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Oth.Oth.50.AllAg.Trabecular_meshwork_cells hg19 TFs and others Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Oth.Oth.50.AllAg.Trabecular_meshwork_cells.bed ...

  19. File list: His.Oth.20.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available His.Oth.20.AllAg.Trabecular_meshwork_cells hg19 Histone Others Trabecular meshwork ...cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/His.Oth.20.AllAg.Trabecular_meshwork_cells.bed ...

  20. File list: His.Oth.05.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available His.Oth.05.AllAg.Trabecular_meshwork_cells hg19 Histone Others Trabecular meshwork ...cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/His.Oth.05.AllAg.Trabecular_meshwork_cells.bed ...

  1. File list: ALL.Oth.10.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ALL.Oth.10.AllAg.Trabecular_meshwork_cells hg19 All antigens Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/ALL.Oth.10.AllAg.Trabecular_meshwork_cells.bed ...

  2. File list: ALL.Oth.05.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ALL.Oth.05.AllAg.Trabecular_meshwork_cells hg19 All antigens Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/ALL.Oth.05.AllAg.Trabecular_meshwork_cells.bed ...

  3. File list: DNS.Oth.10.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available DNS.Oth.10.AllAg.Trabecular_meshwork_cells hg19 DNase-seq Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/DNS.Oth.10.AllAg.Trabecular_meshwork_cells.bed ...

  4. File list: Unc.Oth.10.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Unc.Oth.10.AllAg.Trabecular_meshwork_cells hg19 Unclassified Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Unc.Oth.10.AllAg.Trabecular_meshwork_cells.bed ...

  5. File list: Pol.Oth.50.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Pol.Oth.50.AllAg.Trabecular_meshwork_cells hg19 RNA polymerase Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Pol.Oth.50.AllAg.Trabecular_meshwork_cells.bed ...

  6. File list: Unc.Oth.50.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Unc.Oth.50.AllAg.Trabecular_meshwork_cells hg19 Unclassified Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Unc.Oth.50.AllAg.Trabecular_meshwork_cells.bed ...

  7. File list: Pol.Oth.20.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Pol.Oth.20.AllAg.Trabecular_meshwork_cells hg19 RNA polymerase Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Pol.Oth.20.AllAg.Trabecular_meshwork_cells.bed ...

  8. File list: Unc.Oth.05.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Unc.Oth.05.AllAg.Trabecular_meshwork_cells hg19 Unclassified Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Unc.Oth.05.AllAg.Trabecular_meshwork_cells.bed ...

  9. File list: His.Oth.10.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available His.Oth.10.AllAg.Trabecular_meshwork_cells hg19 Histone Others Trabecular meshwork ...cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/His.Oth.10.AllAg.Trabecular_meshwork_cells.bed ...

  10. File list: Pol.Oth.10.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Pol.Oth.10.AllAg.Trabecular_meshwork_cells hg19 RNA polymerase Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Pol.Oth.10.AllAg.Trabecular_meshwork_cells.bed ...

  11. File list: Oth.Oth.20.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Oth.Oth.20.AllAg.Trabecular_meshwork_cells hg19 TFs and others Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Oth.Oth.20.AllAg.Trabecular_meshwork_cells.bed ...

  12. File list: ALL.Oth.50.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ALL.Oth.50.AllAg.Trabecular_meshwork_cells hg19 All antigens Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/ALL.Oth.50.AllAg.Trabecular_meshwork_cells.bed ...

  13. File list: Oth.Oth.10.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Oth.Oth.10.AllAg.Trabecular_meshwork_cells hg19 TFs and others Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Oth.Oth.10.AllAg.Trabecular_meshwork_cells.bed ...

  14. File list: DNS.Oth.05.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available DNS.Oth.05.AllAg.Trabecular_meshwork_cells hg19 DNase-seq Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/DNS.Oth.05.AllAg.Trabecular_meshwork_cells.bed ...

  15. File list: Unc.Oth.20.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Unc.Oth.20.AllAg.Trabecular_meshwork_cells hg19 Unclassified Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Unc.Oth.20.AllAg.Trabecular_meshwork_cells.bed ...

  16. File list: DNS.Oth.50.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available DNS.Oth.50.AllAg.Trabecular_meshwork_cells hg19 DNase-seq Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/DNS.Oth.50.AllAg.Trabecular_meshwork_cells.bed ...

  17. Modeling the Mechanical Consequences of Age-Related Trabecular Bone Loss by XFEM Simulation.

    Science.gov (United States)

    Fan, Ruoxun; Gong, He; Zhang, Xianbin; Liu, Jun; Jia, Zhengbin; Zhu, Dong

    2016-01-01

    The elderly are more likely to suffer from fracture because of age-related trabecular bone loss. Different bone loss locations and patterns have different effects on bone mechanical properties. Extended finite element method (XFEM) can simulate fracture process and was suited to investigate the effects of bone loss on trabecular bone. Age-related bone loss is indicated by trabecular thinning and loss and may occur at low-strain locations or other random sites. Accordingly, several ideal normal and aged trabecular bone models were created based on different bone loss locations and patterns; then, fracture processes from crack initiation to complete failure of these models were observed by XFEM; finally, the effects of different locations and patterns on trabecular bone were compared. Results indicated that bone loss occurring at low-strain locations was more detrimental to trabecular bone than that occurring at other random sites; meanwhile, the decrease in bone strength caused by trabecular loss was higher than that caused by trabecular thinning, and the effects of vertical trabecular loss on mechanical properties were more severe than horizontal trabecular loss. This study provided a numerical method to simulate trabecular bone fracture and distinguished different effects of the possible occurrence of bone loss locations and patterns on trabecular bone.

  18. Modeling the Mechanical Consequences of Age-Related Trabecular Bone Loss by XFEM Simulation

    Directory of Open Access Journals (Sweden)

    Ruoxun Fan

    2016-01-01

    Full Text Available The elderly are more likely to suffer from fracture because of age-related trabecular bone loss. Different bone loss locations and patterns have different effects on bone mechanical properties. Extended finite element method (XFEM can simulate fracture process and was suited to investigate the effects of bone loss on trabecular bone. Age-related bone loss is indicated by trabecular thinning and loss and may occur at low-strain locations or other random sites. Accordingly, several ideal normal and aged trabecular bone models were created based on different bone loss locations and patterns; then, fracture processes from crack initiation to complete failure of these models were observed by XFEM; finally, the effects of different locations and patterns on trabecular bone were compared. Results indicated that bone loss occurring at low-strain locations was more detrimental to trabecular bone than that occurring at other random sites; meanwhile, the decrease in bone strength caused by trabecular loss was higher than that caused by trabecular thinning, and the effects of vertical trabecular loss on mechanical properties were more severe than horizontal trabecular loss. This study provided a numerical method to simulate trabecular bone fracture and distinguished different effects of the possible occurrence of bone loss locations and patterns on trabecular bone.

  19. Wet cupping therapy restores sympathovagal imbalances in cardiac rhythm.

    Science.gov (United States)

    Arslan, Müzeyyen; Yeşilçam, Nesibe; Aydin, Duygu; Yüksel, Ramazan; Dane, Senol

    2014-04-01

    A recent study showed that cupping had therapeutic effects in rats with myocardial infarction and cardiac arrhythmias. The current studyaimed to investigate the possible useful effects of cupping therapy on cardiac rhythm in terms of heart rate variability (HRV). Forty healthy participants were included. Classic wet cupping therapy was applied on five points of the back. Recording electrocardiography (to determine HRV) was applied 1 hour before and 1 hour after cupping therapy. All HRV parameters increased after cupping therapy compared with before cupping therapy in healthy persons. These results indicate for the first time in humans that cupping might be cardioprotective. In this study, cupping therapy restored sympathovagal imbalances by stimulating the peripheral nervous system.

  20. Football business models: Why did Germany win the World Cup?

    DEFF Research Database (Denmark)

    Cortsen, Kenneth

    2016-01-01

    This article looks into the managerial aspects related to why and how Germany won the 2014 FIFA World Cup.......This article looks into the managerial aspects related to why and how Germany won the 2014 FIFA World Cup....

  1. An Updated Review of the Efficacy of Cupping Therapy

    OpenAIRE

    Cao, Huijuan; Li, Xun; Liu, Jianping

    2012-01-01

    BACKGROUND: Since 1950, traditional Chinese medicine (TCM) cupping therapy has been applied as a formal modality in hospitals throughout China and elsewhere in the world. Based on a previous systematic literature review of clinical studies on cupping therapy, this study presents a thorough review of randomized controlled trials (RCTs) to evaluate the therapeutic effect of cupping therapy. METHOD: Six databases were searched for articles published through 2010. RCTs on cupping therapy for vari...

  2. Genetic theory – a suggested cupping therapy mechanism of action

    OpenAIRE

    Shaban , Tamer; Ravalia , Munir

    2017-01-01

    The Cupping Therapy mechanism of action is not clear. Cupping may increase local blood circulation, and may have an immunomodulation effect. Local and systemic effects of Cupping Therapy were reported. Genetic expression is a physiological process that regulates body functions. Genetic modulation is a reported acupuncture effect. In this article, the authors suggest genetic modulation theory as one of the possible mechanisms of action of cupping therapy.

  3. Long range node-strut analysis of trabecular bone microarchitecture

    DEFF Research Database (Denmark)

    Schmah, Tanya; Marwan, Norbert; Thomsen, Jesper Skovhus

    2011-01-01

    PURPOSE: We present a new morphometric measure of trabecular bone microarchitecture, called mean node strength (NdStr), which is part of a newly developed approach called long range node-strut analysis. Our general aim is to describe and quantify the apparent "latticelike" microarchitecture of th...

  4. Orienteering World Cup hosted by CERN Club

    CERN Multimedia

    Katarina Anthony

    2010-01-01

    Elite runners took to the streets of Geneva for the last leg of the Orienteering World Cup, from 8-10 October. The Geneva finals were hosted by the CERN Orienteering Club and concluded months of competitions held across 5 countries.   Women's World-Cup winner, Simone Niggli (centre).  © Ilknur Colak The final events of the Orienteering World Cup took place in the Old Town of Geneva and Saint-Cergue, with runners following routes prepared by the CERN Orienteering Club. Orienteering is a sport of navigation, using only a compass, map and your sense of direction. The objective is to get to all the points on the map as quickly as possible, choosing your own paths as you run. This was the CERN club’s first successful participation in the World Cup, cementing its reputation as a fixture in the international orienteering world. Orienteering is not your typical Swiss pastime. Developed in Scandinavia, the sport has been gaining popularity internationally. “...

  5. Heat Transfer in a Paper Cup

    Science.gov (United States)

    Ribeiro, Carla

    2017-01-01

    The double-wall paper cup is an everyday object that can be used in the laboratory to study heat transfer. The experiment described here has been done by physics students aged 12-13 years; it can also be used in a different context to prompt debate about environmental issues.

  6. 21 CFR 872.6290 - Prophylaxis cup.

    Science.gov (United States)

    2010-04-01

    ... agents during prophylaxis (cleaning). The dental handpiece spins the rubber cup holding the polishing agent and the user applies it to the teeth to remove debris. (b) Classification. Class I (general... regulation in part 820 of this chapter, with the exception of § 820.180, with respect to general requirements...

  7. Recycling disposable cups into paper plastic composites.

    Science.gov (United States)

    Mitchell, Jonathan; Vandeperre, Luc; Dvorak, Rob; Kosior, Ed; Tarverdi, Karnik; Cheeseman, Christopher

    2014-11-01

    The majority of disposable cups are made from paper plastic laminates (PPL) which consist of high quality cellulose fibre with a thin internal polyethylene coating. There are limited recycling options for PPLs and this has contributed to disposable cups becoming a high profile, problematic waste. In this work disposable cups have been shredded to form PPL flakes and these have been used to reinforce polypropylene to form novel paper plastic composites (PPCs). The PPL flakes and polypropylene were mixed, extruded, pelletised and injection moulded at low temperatures to prevent degradation of the cellulose fibres. The level of PPL flake addition and the use of a maleated polyolefin coupling agent to enhance interfacial adhesion have been investigated. Samples have been characterised using tensile testing, dynamic mechanical analysis (DMA) and thermogravimetric analysis. Use of a coupling agent allows composites containing 40 wt.% of PPL flakes to increase tensile strength of PP by 50% to 30 MPa. The Young modulus also increases from 1 to 2.5 GPa and the work to fracture increases by a factor of 5. The work demonstrates that PPL disposable cups have potential to be beneficially reused as reinforcement in novel polypropylene composites. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. ACCUWIND - Methods for classification of cup anemometers

    Energy Technology Data Exchange (ETDEWEB)

    Dahlberg, J.Aa.; Friis Pedersen, T.; Busche, P.

    2006-05-15

    Errors associated with the measurement of wind speed are the major sources of uncertainties in power performance testing of wind turbines. Field comparisons of well-calibrated anemometers show significant and not acceptable difference. The European CLASSCUP project posed the objectives to quantify the errors associated with the use of cup anemometers, and to develop a classification system for quantification of systematic errors of cup anemometers. This classification system has now been implemented in the IEC 61400-12-1 standard on power performance measurements in annex I and J. The classification of cup anemometers requires general external climatic operational ranges to be applied for the analysis of systematic errors. A Class A category classification is connected to reasonably flat sites, and another Class B category is connected to complex terrain, General classification indices are the result of assessment of systematic deviations. The present report focuses on methods that can be applied for assessment of such systematic deviations. A new alternative method for torque coefficient measurements at inclined flow have been developed, which have then been applied and compared to the existing methods developed in the CLASSCUP project and earlier. A number of approaches including the use of two cup anemometer models, two methods of torque coefficient measurement, two angular response measurements, and inclusion and exclusion of influence of friction have been implemented in the classification process in order to assess the robustness of methods. The results of the analysis are presented as classification indices, which are compared and discussed. (au)

  9. Anorexia Nervosa: Analysis of Trabecular Texture with CT.

    Science.gov (United States)

    Tabari, Azadeh; Torriani, Martin; Miller, Karen K; Klibanski, Anne; Kalra, Mannudeep K; Bredella, Miriam A

    2017-04-01

    Purpose To determine indexes of skeletal integrity by using computed tomographic (CT) trabecular texture analysis of the lumbar spine in patients with anorexia nervosa and normal-weight control subjects and to determine body composition predictors of trabecular texture. Materials and Methods This cross-sectional study was approved by the institutional review board and compliant with HIPAA. Written informed consent was obtained. The study included 30 women with anorexia nervosa (mean age ± standard deviation, 26 years ± 6) and 30 normal-weight age-matched women (control group). All participants underwent low-dose single-section quantitative CT of the L4 vertebral body with use of a calibration phantom. Trabecular texture analysis was performed by using software. Skewness (asymmetry of gray-level pixel distribution), kurtosis (pointiness of pixel distribution), entropy (inhomogeneity of pixel distribution), and mean value of positive pixels (MPP) were assessed. Bone mineral density and abdominal fat and paraspinal muscle areas were quantified with quantitative CT. Women with anorexia nervosa and normal-weight control subjects were compared by using the Student t test. Linear regression analyses were performed to determine associations between trabecular texture and body composition. Results Women with anorexia nervosa had higher skewness and kurtosis, lower MPP (P anorexia nervosa. Conclusion Patients with anorexia nervosa had increased skewness and kurtosis and decreased entropy and MPP compared with normal-weight control subjects. These parameters were associated with lowest lifetime weight and duration of amenorrhea, but there were no such associations with bone mineral density. These findings suggest that trabecular texture analysis might contribute information about bone health in anorexia nervosa that is independent of that provided with bone mineral density. © RSNA, 2016.

  10. Changes of enzyme activities in lens after glaucoma trabecular resection

    Directory of Open Access Journals (Sweden)

    Jian-Ping Wang

    2013-08-01

    Full Text Available AIM: To observe the change of lens antioxidant enzyme activity after glaucoma trabecular resection. METHODS: Thirty-two eyes of sixteen New-Zealand rabbits(2.2-2.4kgwere divided into two groups. The left eyes of rabbits underwent standard glaucoma trabecular resection were treatment group, and the normal right eyes served as controls. Transparency of lenses was monitored by a slit-lamp biomicroscopy before and after glaucoma trabecular resection. The morphology of lens cells was observed under the light microscope.The activities of Na+-K+-ATPase,catalase(CAT, glutathion peroxidase(GSH-px, glutathione reductase(GR, superoxide dismutase(SODand content of malondialdehyde(MDAin lenses were detected six months after trabecular resection. RESULTS: Lenses were clear in both treatment group and normal control group during the six months after operation. The morphology and structure of lens cells were normal under the light microscope in both operation group and normal group. The activity of lens cells antioxidant enzyme activity were significantly decreased in operation group compared with control group, Na+-K+-ATPase declined by 20.97%, CAT declined by 16.36%, SOD declined by 4.46%, GR declined by 4.85%, GSH-px declined by 10.02%, and MDA increased by 16.31%. CONCLUSION: Glaucoma trabecular resection can induce the change of Na+-K+-ATPase, CAT, GSH-px, GR, SOD and MDA in lens of rabbit. Glaucoma filtration surgery for the occurrence of cataract development mechanism has important guiding significance.

  11. A Procedure for Classification of Cup-Anemometers

    DEFF Research Database (Denmark)

    Friis Pedersen, Troels; Paulsen, Uwe Schmidt

    1997-01-01

    The paper proposes a classification procedure for cup-anemometers based on similar principles as for power converters. A range of operational parameters are established within which the response of the cup-anemometer is evaluated. The characteristics of real cup-anemometers are fitted...... to a realistic 3D cup-anemometer model. Afterwards, the model is used to calculate the response under the range of operational conditions which are set up for the classification. Responses are compared to the normal linear calibration relationship, derived from Wind tunnel calibrations. Results of the 3D cup-anemometer...

  12. Dispersal of seeds from splash-cup plants

    Science.gov (United States)

    Pepper, Rachel

    2017-11-01

    Splash cup plants disperse their seeds with the help of raindrops. The seeds sit in a small (mm-scale) conical cup and are ejected upon drop impact. The seeds are ejected at velocities up to five times the impact speed of the raindrop, and are dispersed up to 1 m away from the parent plant, which is only a few cm high. Previous work investigating the mechanism of this remarkable dispersal predicted an optimum cup opening angle of around 40°, which matched reasonably well with experiments performed with 3D-printed splash cup models. Those experiments were done with off-center drop impacts on initially empty cups with no seeds. We discuss similar experiments for cups that are not initially empty, but rather contain seed mimics, water, or both seeds and water. For some of these realistic initial states results are strikingly different from empty cups. Connections to theory will also be discussed.

  13. High proximal migration rate of a partially covered "big cup" duodenal stent in patients with malignant gastric outlet obstruction

    NARCIS (Netherlands)

    van den Berg, Maarten W.; Walter, Daisy; Vleggaar, Frank P.; Siersema, Peter D.; Fockens, Paul; van Hooft, Jeanin E.

    2014-01-01

    Endoscopic placement of self-expandable metal stents (SEMS) has emerged as a palliative treatment for patients with malignant gastric outlet obstruction (GOO). Recently, a new partially covered "big cup" SEMS has been developed to prevent both stent migration and tissue ingrowth. The aim of the

  14. STRUCTURAL SAFETY ANALYSIS OF STADIUMS FOR THE 2018 FIFA WORLD CUP IN RUSSIA. FORMULATION OF PROBLEMS OF STRUCTURAL ANALYSIS

    Directory of Open Access Journals (Sweden)

    Alexander M. Belostotsky

    2018-03-01

    Full Text Available The article presents structural safety analysis of the three-dimensional long-span systems “ground base – reinforced concrete foundation structures and stands - metal structures of the coating and facades” of football stadiums for the 2018 World Cup in Russia with basic and special combinations of loads and formulation problems of future in-vestigations.

  15. Flow distortion on boom mounted cup anemometers

    DEFF Research Database (Denmark)

    Lindelöw, Per Jonas Petter; Friis Pedersen, Troels; Gottschall, Julia

    In this report we investigate on wind direction dependent errors in the measurement of the horizontal wind speed by boom mounted cup anemometers. The boom mounting on the studied lattice tower is performed according to IEC standard design rules, yet, larger deviations than predicted by flow models...... are observed. The errors on the measurements are likely caused by an underestimation of the flow distortions around the tower. In this paper an experimental method for deriving a correction formula and an in-field calibration is suggested. The method is based on measurements with two cup anemometers mounted...... in the measurement of wind turbine power performance, wind resource assessment and for providing purposeful in-field comparisons between different sensors, e.g. lidar anemometers. With the proposed method, direction dependent errors can be extracted and the mast flow distortion effect on the wind measurements...

  16. Management of knee osteoarthritis with cupping therapy

    Directory of Open Access Journals (Sweden)

    Asim Ali Khan

    2013-01-01

    Full Text Available The study aimed to evaluate the effect of cupping therapy at a clinical setting for knee osteoarthritis. A randomized, controlled clinical trial was conducted. Cupping was performed on 0-6 th day; 9-11 th day and 14 th day, i.e., 11 sittings follow-up to determine longer term carryover of treatment effects utilizing both objective and subjective assessment. The assessment was performed before and after treatment spreading over a period of 15 days. The results of this study shows significant and better results in the overall management of knee osteoarthritis, particularly in relieving pain, edema, stiffness and disability. The efficacy of treatment with cupping therapy in relieving signs and symptoms of knee osteoarthritis is comparable to that of acetaminophen 650 mg thrice a day orally, in terms of analgesia, anti-inflammatory and resolution of edema with minimal and temporary side-effects like echymosis and blister formation while as control drug has greater side-effects particularly on upper gastrointestinal tract. It is recommended that further studies are conducted with a larger study samples and of longer duration.

  17. Management of knee osteoarthritis with cupping therapy.

    Science.gov (United States)

    Khan, Asim Ali; Jahangir, Umar; Urooj, Shaista

    2013-10-01

    The study aimed to evaluate the effect of cupping therapy at a clinical setting for knee osteoarthritis. A randomized, controlled clinical trial was conducted. Cupping was performed on 0-6(th) day; 9-11(th) day and 14(th) day, i.e., 11 sittings follow-up to determine longer term carryover of treatment effects utilizing both objective and subjective assessment. The assessment was performed before and after treatment spreading over a period of 15 days. The results of this study shows significant and better results in the overall management of knee osteoarthritis, particularly in relieving pain, edema, stiffness and disability. The efficacy of treatment with cupping therapy in relieving signs and symptoms of knee osteoarthritis is comparable to that of acetaminophen 650 mg thrice a day orally, in terms of analgesia, anti-inflammatory and resolution of edema with minimal and temporary side-effects like echymosis and blister formation while as control drug has greater side-effects particularly on upper gastrointestinal tract. It is recommended that further studies are conducted with a larger study samples and of longer duration.

  18. Osteoarthritis Imaging by Quantification of Tibial Trabecular Bone

    DEFF Research Database (Denmark)

    Marques, Joselene

    The pathogenesis of osteoarthritis (OA) includes complex events in the whole joint. In this project, we combined machine-learning techniques in a texture analysis framework and evaluated it in a longitudinal study, where magnetic resonance images of knees were used to quantify the tibial trabecular...... bone in both a marker for OA diagnosis and another marker for prediction of tibial cartilage loss. By multiple-instance learning, we also investigated which region of the tibia provided the best prognosis for cartilage loss. The inferior part of the tibial bone was classified as the most relevant...... region and a preliminary radiological reading of the knees with high and low risks of cartilage loss suggested the prognosis marker captured aspects of the tibia vertical trabecularization to define the prognosis. Besides presenting a bone marker able to predict disease progression and diagnostic marker...

  19. Trabecular bone structure and strength - remodelling and repair

    DEFF Research Database (Denmark)

    Mosekilde, Lis; Ebbesen, Ebbe Nils; Erikstrup, Lise Tornvig

    2000-01-01

    The strength of the spinal trabecular bone declines by a factor of 4-5 from the age of 20 to 80 years. At the same time, the volumetric (apparent) density declines by a factor of only 2. This discrepancy can be explained by the known power relationship between density and strength; this power rel......; and the hydraulic effect of the bone marrow. In order to answer these questions, more in vitro and in vivo studies on human bone in relation to aging, to immobilisation, to exercise and in relation to different treatment regimens are needed.......The strength of the spinal trabecular bone declines by a factor of 4-5 from the age of 20 to 80 years. At the same time, the volumetric (apparent) density declines by a factor of only 2. This discrepancy can be explained by the known power relationship between density and strength; this power...

  20. A rig for acquisition of standardized trabecular bone radiographs

    Energy Technology Data Exchange (ETDEWEB)

    Podsiadlo, P.; Stachowiak, G.W. [Univ. of Western Australia, Crawley (Australia). Dept. of Mechanical and Materials Engineering

    2002-04-01

    To assess osteoarthritic changes in knee joints a radiography rig for acquisition of standardized radiographs of trabecular bone has been developed. The rig contains a steel frame on castors, a turntable, a cassette holder frame, calibration Plexiglas sheets, body supports and points. It is used to lock the patient in a standardized position. A film cassette holder frame was also developed to reduce scattering of X-rays, and consequently the amount of noise in the radiographs. Calibration Plexiglas sheets were mounted on ball bearing slides to obtain radiographs without a calibration pattern (suitable for the analysis of trabecular bone texture) and radiographs containing a calibration pattern (suitable for the measurement of leg alignment)

  1. Multiscale modelling of trabecular bone: from micro to macroscale

    OpenAIRE

    Levrero Florencio, Francesc

    2017-01-01

    Trabecular bone has a complex and porous microstructure. This study develops approaches to determine the mechanical behaviour of this material at the macroscopic level through the use of homogenisation-based multiscale methods using micro-finite element simulations. In homogenisation-based finite element methods, a simulation involving a representative volume element of the microstructure of the considered material is performed with a specific set of boundary conditions. The ma...

  2. Creep of trabecular bone from the human proximal tibia

    Energy Technology Data Exchange (ETDEWEB)

    Novitskaya, Ekaterina, E-mail: eevdokim@ucsd.edu [Mechanical and Aerospace Engineering, UC, San Diego, La Jolla, CA 92093 (United States); Materials Science and Engineering Program, UC, San Diego, La Jolla, CA 92093 (United States); Zin, Carolyn [Materials Science and Engineering, Johns Hopkins University, Baltimore, MD 21218 (United States); Chang, Neil; Cory, Esther; Chen, Peter [Departments of Bioengineering and Orthopaedic Surgery, UC, San Diego, La Jolla, CA 92093 (United States); D’Lima, Darryl [Shiley Center for Orthopaedic Research and Education, Scripps Health, La Jolla, CA 92037 (United States); Sah, Robert L. [Materials Science and Engineering Program, UC, San Diego, La Jolla, CA 92093 (United States); Departments of Bioengineering and Orthopaedic Surgery, UC, San Diego, La Jolla, CA 92093 (United States); McKittrick, Joanna [Mechanical and Aerospace Engineering, UC, San Diego, La Jolla, CA 92093 (United States); Materials Science and Engineering Program, UC, San Diego, La Jolla, CA 92093 (United States)

    2014-07-01

    Creep is the deformation that occurs under a prolonged, sustained load and can lead to permanent damage in bone. Creep in bone is a complex phenomenon and varies with type of loading and local mechanical properties. Human trabecular bone samples from proximal tibia were harvested from a 71-year old female cadaver with osteoporosis. The samples were initially subjected to one cycle load up to 1% strain to determine the creep load. Samples were then loaded in compression under a constant stress for 2 h and immediately unloaded. All tests were conducted with the specimens soaked in phosphate buffered saline with proteinase inhibitors at 37 °C. Steady state creep rate and final creep strain were estimated from mechanical testing and compared with published data. The steady state creep rate correlated well with values obtained from bovine tibial and human vertebral trabecular bone, and was higher for lower density samples. Tissue architecture was analyzed by micro-computed tomography (μCT) both before and after creep testing to assess creep deformation and damage accumulated. Quantitative morphometric analysis indicated that creep induced changes in trabecular separation and the structural model index. A main mode of deformation was bending of trabeculae. - Highlights: • Compressive creep tests of human trabecular bone across the tibia were performed. • The creep rate was found to be inversely proportional to the density of the samples. • μ-computed tomography before and after testing identified regions of deformation. • Bending of the trabeculae was found to be the main deformation mode.

  3. Comparison of different plasticity criteria for trabecular bone failure modelling

    Czech Academy of Sciences Publication Activity Database

    Jiroušek, Ondřej

    2008-01-01

    Roč. 8, č. 1 (2008), s. 10177-10178 ISSN 1617-7061. [Annual Meeting of International Association of Applied Mathematics and Mechanics. Bremen, 31.03.2008-04.04.2008] R&D Projects: GA ČR(CZ) GA103/05/1020 Institutional research plan: CEZ:AV0Z20710524 Keywords : nanoindentation * plasticity criteria * trabecular bone Subject RIV: FI - Traumatology, Orthopedics

  4. [Progress of researches on the mechanism of cupping therapy].

    Science.gov (United States)

    Cui, Shuai; Cui, Jin

    2012-12-01

    Cupping therapy of Chinese medicine is able to relieve a variety of diseases or clinical conditions, which results from the comprehensive effects of multiple types of stimulation exerted onto the regional acupoint areas. Among the stimuli, the negative pressure from cupping is one of the main factors inducing therapeutic effects. In the present paper, the authors review development of researches on the underlying mechanism of therapeutic effects of cupping-negative pressure from 1) the factor of intra-cup negative pressure; 2) influence of intra-cup negative pressure on cup-blackspot formation; 3) influence of cupping on regional blood vessels and blood flow; 4) effect of cupping on regional ultrastructure of the capillary in the raw-surface tissue; 5) effect of cupping-negative pressure on regional endothelial cells; and 6) biological effects of negative pressure drainage. Generally, cupping induced negative pressure can dilate local blood vessels to improve microcirculation, promote capillary endothelial cells repair, accelerate granulation and angiogenesis, etc., in the regional tissues, normalizing the patients' functional state at last.

  5. History of cupping (Hijama): a narrative review of literature.

    Science.gov (United States)

    Qureshi, Naseem Akhtar; Ali, Gazzaffi Ibrahim; Abushanab, Tamer Shaban; El-Olemy, Ahmed Tawfik; Alqaed, Meshari Saleh; El-Subai, Ibrahim S; Al-Bedah, Abdullah M N

    2017-05-01

    Cupping (Hijama in Arabic) is an ancient, holistic method for the treatment of a variety of diseases. Though the exact origin of cupping therapy is a matter of controversy, its use has been documented in early Egyptian and Chinese medical practices. Diverse human civilizations have contributed to the historical development and continuation of cupping therapy. This narrative review describes the history of cupping, historical definitions, cupping instruments and uses of cupping therapy. Electronic searches of relevant databases (PubMed, Google Scholar and OvidSP) were conducted using keywords and Boolean operators. Manual searches and references of published articles and books were also conducted. A number of articles (N = 625) were retained for extensive review, and finally 83 articles were included in this paper. The historical descriptions of cupping therapy were found in ancient human civilizations of the Eastern and Western world. There were inconsistent data concerning the origin of cupping, definitions, instruments, procedures, definite advancements and research in Hijama over centuries. Cupping therapy fell out of favor in 17th and mid-18th centuries but recovered popularity in modern medicine. Currently, cupping therapy is used for health promotion, prophylaxis and treatment of a variety of diseases around the world. Cupping therapy with a good safety profile has a checkered history and is a well-recognized traditional method for managing medical conditions. Currently, the scope of cupping therapy is expanding, and a growing body of research is providing additional evidence-based data for the further advancement of cupping therapy in the treatment of a variety of diseases.

  6. Histomorphometry of Trabecular Bone of Caudal Vertebrae During Rat Pregnancy

    Directory of Open Access Journals (Sweden)

    S.M. Shahtaheri

    2003-04-01

    Full Text Available Pregnancy make demands upon maternal calcium hemeostasis and the extent to which the maternal bone mass is effected remains uncertain. Recently changes in the bone mass during human pregnancy have been associated also with the transformation of the cancellous architecture and the bone surface available for exchange. These jistomorphometrical structural changes were examined further in an animal model. Using uniparous laboratory rats fed at libitum, the histomorphometry of cancellous bone was compared in undecalcified of caudal vertebrae. Between 3 and 6 sections (8 m were analysed by an automated trabecular analysis system (TAS which measures a comprehensive range of structural variables including the trabecular separation, number, connectivity and width. There was an early stimulation of bone formation that was indicated by generation of thicker and interconnected trabeculae. However in caudal vertebrae, there were architectural changes in cancellous bone commencing with a significant increase in the trabecular separation. ‌‌ It was concluded that strengthens the cancellous component of the maternal skeleton possibly to counter increased load and to facilitate mineral mobilisation in maternal/neonate exchange during the subsequent lactation period.

  7. Limited Trabecular Bone Density Heterogeneity in the Human Skeleton

    Directory of Open Access Journals (Sweden)

    Habiba Chirchir

    2016-01-01

    Full Text Available There is evidence for variation in trabecular bone density and volume within an individual skeleton, albeit in a few anatomical sites, which is partly dependent on mechanical loading. However, little is known regarding the basic variation in trabecular bone density throughout the skeleton in healthy human adults. This is because research on bone density has been confined to a few skeletal elements, which can be readily measured using available imaging technology particularly in clinical settings. This study comprehensively investigates the distribution of trabecular bone density within the human skeleton in nine skeletal sites (femur, proximal and distal tibia, third metatarsal, humerus, ulna, radius, third metacarpal, and axis in a sample of N=20 individuals (11 males and 9 females. pQCT results showed that the proximal ulna (mean = 231.3 mg/cm3 and axis vertebra (mean = 234.3 mg/cm3 displayed significantly greater (p0.01. The homogeneity of the majority of elements suggests that these sites are potentially responsive to site-specific genetic factors. Secondly, the lack of correlation between elements (p>0.05 suggests that density measurements of one anatomical region are not necessarily accurate measures of other anatomical regions.

  8. Prediction of mechanical properties of trabecular bone using quantitative MRI

    International Nuclear Information System (INIS)

    Lammentausta, E; Hakulinen, M A; Jurvelin, J S; Nieminen, M T

    2006-01-01

    Techniques for quantitative magnetic resonance imaging (MRI) have been developed for non-invasive estimation of the mineral density and structure of trabecular bone. The R* 2 relaxation rate (i.e. 1/T* 2 ) is sensitive to bone mineral density (BMD) via susceptibility differences between trabeculae and bone marrow, and by binarizing MRI images, structural variables, such as apparent bone volume fraction, can be assessed. In the present study, trabecular bone samples of human patellae were investigated in vitro at 1.5 T to determine the ability of MRI-derived variables (R* 2 and bone volume fraction) to predict the mechanical properties (Young's modulus, yield stress and ultimate strength). Further, the MRI variables were correlated with reference measurements of volumetric BMD and bone area fraction as determined with a clinical pQCT system. The MRI variables correlated significantly (p 2 and MRI-derived bone volume fraction further improved the prediction of yield stress and ultimate strength. Although pQCT showed a trend towards better prediction of the mechanical properties, current results demonstrate the feasibility of combined MR imaging of marrow susceptibility and bone volume fraction in predicting the mechanical strength of trabecular bone and bone mineral density

  9. Compilation of LLNL CUP-2 Data

    Energy Technology Data Exchange (ETDEWEB)

    Eppich, G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kips, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lindvall, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-07-31

    The CUP-2 uranium ore concentrate (UOC) standard reference material, a powder, was produced at the Blind River uranium refinery of Eldorado Resources Ltd. in Canada in 1986. This material was produced as part of a joint effort by the Canadian Certified Reference Materials Project and the Canadian Uranium Producers Metallurgical Committee to develop a certified reference material for uranium concentration and the concentration of several impurity constituents. This standard was developed to satisfy the requirements of the UOC mining and milling industry, and was characterized with this purpose in mind. To produce CUP-2, approximately 25 kg of UOC derived from the Blind River uranium refinery was blended, homogenized, and assessed for homogeneity by X-ray fluorescence (XRF) analysis. The homogenized material was then packaged into bottles, containing 50 g of material each, and distributed for analysis to laboratories in 1986. The CUP-2 UOC standard was characterized by an interlaboratory analysis program involving eight member laboratories, six commercial laboratories, and three additional volunteer laboratories. Each laboratory provided five replicate results on up to 17 analytes, including total uranium concentration, and moisture content. The selection of analytical technique was left to each participating laboratory. Uranium was reported on an “as-received” basis; all other analytes (besides moisture content) were reported on a “dry-weight” basis. A bottle of 25g of CUP-2 UOC standard as described above was purchased by LLNL and characterized by the LLNL Nuclear Forensics Group. Non-destructive and destructive analytical techniques were applied to the UOC sample. Information obtained from short-term techniques such as photography, gamma spectrometry, and scanning electron microscopy were used to guide the performance of longer-term techniques such as ICP-MS. Some techniques, such as XRF and ICP-MS, provided complementary types of data. The results

  10. Springback optimization in automotive Shock Absorber Cup with Genetic Algorithm

    Science.gov (United States)

    Kakandikar, Ganesh; Nandedkar, Vilas

    2018-02-01

    Drawing or forming is a process normally used to achieve a required component form from a metal blank by applying a punch which radially draws the blank into the die by a mechanical or hydraulic action or combining both. When the component is drawn for more depth than the diameter, it is usually seen as deep drawing, which involves complicated states of material deformation. Due to the radial drawing of the material as it enters the die, radial drawing stress occurs in the flange with existence of the tangential compressive stress. This compression generates wrinkles in the flange. Wrinkling is unwanted phenomenon and can be controlled by application of a blank-holding force. Tensile stresses cause thinning in the wall region of the cup. Three main types of the errors occur in such a process are wrinkling, fracturing and springback. This paper reports a work focused on the springback and control. Due to complexity of the process, tool try-outs and experimentation may be costly, bulky and time consuming. Numerical simulation proves to be a good option for studying the process and developing a control strategy for reducing the springback. Finite-element based simulations have been used popularly for such purposes. In this study, the springback in deep drawing of an automotive Shock Absorber Cup is simulated with finite element method. Taguchi design of experiments and analysis of variance are used to analyze the influencing process parameters on the springback. Mathematical relations are developed to relate the process parameters and the resulting springback. The optimization problem is formulated for the springback, referring to the displacement magnitude in the selected sections. Genetic Algorithm is then applied for process optimization with an objective to minimize the springback. The results indicate that a better prediction of the springback and process optimization could be achieved with a combined use of these methods and tools.

  11. Is cupping blister harmful?-A proteomical analysis of blister fluid induced by cupping therapy and scald.

    Science.gov (United States)

    Liu, Zhidan; Chen, Chunlan; Li, Xiaoyan; Zhao, Chuang; Li, Zunyuan; Liang, Wei; Lin, Yufang

    2018-02-01

    Cupping therapy has a long history in traditional medicine especially in Asian countries. It was controversial whether cupping induced blisters are beneficial to healing effects, and the formation and content in the blisters remain unexplored. We aimed to identify and compare the molecular components of the blister fluid from the cupping therapy and the scalds to explore the necessary of inducing cupping induced blisters. Fluid sample of blisters from fifteen patients receiving cupping therapy (Cupping group) and scald burns (Scald group) were collected in this study. Proteins from the blisters were separated by two-dimensional electrophoresis (2D-gel) and further analyzed by mass spectrometry. In addition, the changes in particular proteins were confirmed by Western blotting. The protein components are significantly different between blister from cupping therapy and scalds. The immune responses, oxidative stress and metabolic related proteins (Ig lambda-2 chain C regions, Ig gamma-1 chain C region, hemopexin, prdx2, calmodulin, succinyl-CoA ligase and tetranectin) were increased, whereas the hemoglobin subunit beta was decreased in the Cupping group compared with the Scald group. Cupping induced blisters contain several proteins which relate to the activation of certain immune pathways including anti-oxidation, anti-apoptosis, tissue repairing and metabolic regulation. This proteomic analysis may indicate a significant clue to the mechanism study of cupping. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Development of a classification system for cup anemometers - CLASSCUP

    DEFF Research Database (Denmark)

    Friis Pedersen, Troels

    2003-01-01

    classification system. A classification method for cup anemometers has been developed, which proposes general external operational ranges to be used. Anormal category range connected to ideal sites of the IEC power performance standard was made, and another extended category range for complex terrain...... the objectives to quantify the errors associated with the use of cup anemometers, and to determine the requirements for an optimum design of a cup anemometer, and to develop a classification system forquantification of systematic errors of cup anemometers. The present report describes this proposed...... was proposed. General classification indices were proposed for all types of cup anemometers. As a resultof the classification, the cup anemometer will be assigned to a certain class: 0.5, 1, 2, 3 or 5 with corresponding intrinsic errors (%) as a vector instrument (3D) or as a horizontal instrument (2D...

  13. Wet-cupping removes oxidants and decreases oxidative stress.

    Science.gov (United States)

    Tagil, Suleyman Murat; Celik, Huseyin Tugrul; Ciftci, Sefa; Kazanci, Fatmanur Hacievliyagil; Arslan, Muzeyyen; Erdamar, Nazan; Kesik, Yunus; Erdamar, Husamettin; Dane, Senol

    2014-12-01

    Wet-cupping therapy is one of the oldest known medical techniques. Although it is widely used in various conditions such as acute\\chronic inflammation, infectious diseases, and immune system disorders, its mechanism of action is not fully known. In this study, we investigated the oxidative status as the first step to elucidate possible mechanisms of action of wet cupping. Wet cupping therapy is implemented to 31 healthy volunteers. Venous blood samples and Wet cupping blood samples were taken concurrently. Serum nitricoxide, malondialdehyde levels and activity of superoxide dismutase and myeloperoxidase were measured spectrophotometrically. Wet cupping blood had higher activity of myeloperoxidase, lower activity of superoxide dismutase, higher levels of malondialdehyde and nitricoxide compared to the venous blood. Wet cupping removes oxidants and decreases oxidative stress. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. Proteomic effects of wet cupping (Al-hijamah).

    Science.gov (United States)

    Almaiman, Amer A

    2018-01-01

    Wet cupping (Al-hijamah) is a therapeutic technique practiced worldwide as a part of the Unani system of medicine. It involves bloodletting from acupoints on a patient's skin to produce a therapeutic outcome. A thorough review of research articles on wet cupping with relevance to proteomics field that are indexed by Google Scholar, PubMed, and/or Science Direct databases was performed. Eight original research articles were summarized in this paper. Overall, wet cupping did not have a significant effect on C-reactive protein, Hsp-27, sister chromatid exchanges, and cell replication index. In contrast, wet cupping was found to produce higher oxygen saturation, eliminate lactate from subcutaneous tissues, remove blood containing higher levels of malondialdehyde and nitric oxide, and produce higher activity of myeloperoxidase. The proteomic effects of wet cupping therapy have not been adequately investigated. Thus, future studies on wet cupping that use systemic and sound protocols to avoid bias should be conducted.

  15. Paradoxical, Cupping-Induced Localized Psoriasis: A Koebner Phenomenon.

    Science.gov (United States)

    Vender, Reid; Vender, Ronald

    2015-01-01

    Cupping therapy is a traditional Chinese medicine used to heal psoriasis. The Koebner phenomenon is the occurrence of psoriatic lesions at the site of cutaneous injury. To describe the first case of biopsy-proven cupping-induced localized psoriasis, an example of the Koebner phenomenon. The histopathology of the lesions is described. A brief review of the literature regarding cupping therapy and its efficacy are discussed. A 45-year-old Asian male presented himself to the dermatology clinic for further treatment of his psoriasis. Four unusually circular plaques on the lower back were discovered. Pathologic diagnosis revealed an early lesion of psoriasis. on further inquiry, the patient admitted to undergoing a recent "cupping" procedure in an attempt to cure his condition. The efficacy of cupping therapy is controversial, and psoriatic patients may develop localized psoriasis through koebnerization as a result of cupping therapy rather than achieve desirable therapeutic benefits. © 2014 Canadian Dermatology Association.

  16. Suitability of texture features to assess changes in trabecular bone architecture

    DEFF Research Database (Denmark)

    Veenland, JF; Grashuis, JL; Weinans, H

    2002-01-01

    The purpose of this study was to determine the ability of texture features to assess changes in trabecular bone architecture as projected in radiographs. Micro-CT datasets of trabecular bone were processed to simulate different changes in architecture. Radiographs were simulated by projecting the 3......D-bone structure. Texture features, based on mathematical morphology, determined on the simulated radiographs were able to detect structural changes in the trabecular bone....

  17. Disturbances of trabecular architecture in the upper end of the femur in childhood

    International Nuclear Information System (INIS)

    Osborne, D.; Effmann, E.

    1981-01-01

    Trabeculae represent the smallest functional component of bone visible with conventional radiographic methods. Their architecture is affected by mechanical, hormonal, nutritional, genetic, toxic, and local disease processes. Trabecular evaluation, if coupled with a knowledge of normal trabecular development in children, can represent a sensitive index of bone malfunction, at least as judged radiographically. This paper explores alterations in the trabecular architecture of the upper end of the femur in children. (orig.)

  18. A reversible strain-induced electrical conductivity in cup-stacked carbon nanotube

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, T [Shinshu University; Morokuma, Keiji [ORNL; Meunier, Vincent [ORNL; Meunier, V. [Rensselaer Polytechnic Institute (RPI); Terrones Maldonado, Mauricio [ORNL; Muramatsu, H [Shinshu University; Sumpter, Bobby G [ORNL; Kim, Y A [Shinshu University

    2013-01-01

    We have used in-situ current-voltage measurements of cup-stacked carbon nanotubes (CSCNTs) to establish a reversible strain induced (compressive bending) semiconducting to metallic behavior. The corresponding electrical resistance decreases by two orders of magnitude during the process, and reaches values comparable to those of highly crystalline multi-walled carbon nanotube (MWCNT) and graphite. Joule heating experiments on the same CSCNTs showed that the edges of individual cups merge to form loops induced by the heating process. The resistance of these looped CSCNTs was close to that of highly deformed CSCNTs (and crystalline MWCNTs), thus suggesting that a similar conduction mechanism took place in both cases. Using a combination of molecular dynamics and first-principles calculations based on density functional theory, we conclude that an edge-to-edge interlayer transport mechanism results in conduction channels at the compressed side of the CSCNTs due to electronic density overlap between individual cups, thus making CSCNT more conducting. This strain-induced CSCNT semiconductor to metal transition could potentially be applied to enabling functional composite materials (e.g. mechanical sensors) with enhanced and tunable conducting properties upon compression.

  19. Assessing Wear of the Acetabular Cup Using Computed Tomography: an ex vivo Study

    International Nuclear Information System (INIS)

    Olivecrona, L.; Jedenmalm, A.; Aspelin, P.; Weidenhielm, L.; Noz, M.E.; Maguire, G.Q.; Zeleznik, M.P.; Olivecrona, H.

    2005-01-01

    Purpose: To validate a clinically useful method for measuring acetabular cup wear using computed tomography (CT). Material and Methods: Eight uncemented acetabular cups were scanned twice ex vivo using CT. The linear penetration depth of the femoral component head into the cup and the thickness of the remaining polyethylene liner were measured in the CT volumes using dedicated software. Two independent examiners twice assessed each volume. The CT measurements were compared to direct measurements using a coordinate measuring device and micrometer measurements. Results: Accuracy of wear measurements expressed as penetration depth was ±0.6 and ±1.0 mm for the two examiners, respectively, with no significant differences between examiners, trials, and CT scans. Accuracy of measurements of remaining polyethylene was ±1.3 and ±1.0 mm, respectively, for the two examiners. Systematic differences between examiners were found, but no significant differences between trials and CT scans. These differences were due to different interpretations of metal artifacts in the volumes. Conclusion: The proposed CT method for evaluating wear as head penetration depth allows for reliable wear detection at a clinically relevant level. Measurements of remaining polyethylene on CT volumes are not as reliable as wear measurements owing to metal artifacts

  20. Effect of Seed Density on Splash Cup Seed Dispersal

    Science.gov (United States)

    Wigger, Patrick; Pepper, Rachel

    2017-11-01

    Splash cup plants are plants that utilize a small, mm-sized cup filled with seeds as a method of seed dispersal. The cup uses kinetic energy of an incident raindrop in order to project the seeds away from the plant up to 1 meter. The dispersal distance is important to ensure the offspring are not clustered too tightly to the parent plant. It has previously been found that a cup angle of 40 degrees to the horizontal is optimal for maximum dispersal of water from cups with no seeds. In this study we examine if the 40 degree cup is optimal for cups containing seeds with varying densities. We released uniform water drops above 5.0 mm 3D printed models of splash cups, using 1.0 mm plastic and glass microspheres of varying densities to simulate seeds. We observed the dispersal characteristics of each bead type by measuring the final seed locations after each splash, and by recording high speed video to determine the angle and velocity of the seeds as they exited the cup.

  1. ACCUWIND - Methods for classification of cup anemometers

    DEFF Research Database (Denmark)

    Dahlberg, J.-Å.; Friis Pedersen, Troels; Busche, P.

    2006-01-01

    of assessment of systematic deviations. The present report focuses on methods that can beapplied for assessment of such systematic deviations. A new alternative method for torque coefficient measurements at inclined flow have been developed, which have then been applied and compared to the existing methods...... developed in the CLASSCUP projectand earlier. A number of approaches including the use of two cup anemometer models, two methods of torque coefficient measurement, two angular response measurements, and inclusion and exclusion of influence of friction have been implemented in theclassification process...

  2. An expression relating breaking stress and density of trabecular bone

    DEFF Research Database (Denmark)

    Rajapakse, C.S.; Thomsen, J.S.; Ortiz, J.S.E.

    2004-01-01

    Bone mineral density (BMD) is the principal diagnostic tool used in clinical settings to diagnose and monitor osteoporosis. Experimental studies on ex vivo bone samples from multiple skeletal locations have been used to propose that their breaking stress bears a power-law relationship to volumetric...... previously published data on bone samples from iliac crest and vertebral body. It represents the experimental biomechanical data at least as well as the power-law, and provides means for extrapolating results from small biopsy samples to an entire bone. In addition, changes caused by trabecular thinning...

  3. Automatic analysis of trabecular bone structure from knee MRI

    DEFF Research Database (Denmark)

    Marques, Joselene; Granlund, Rabia; Lillholm, Martin

    2012-01-01

    We investigated the feasibility of quantifying osteoarthritis (OA) by analysis of the trabecular bone structure in low-field knee MRI. Generic texture features were extracted from the images and subsequently selected by sequential floating forward selection (SFFS), following a fully automatic......, uncommitted machine-learning based framework. Six different classifiers were evaluated in cross-validation schemes and the results showed that the presence of OA can be quantified by a bone structure marker. The performance of the developed marker reached a generalization area-under-the-ROC (AUC) of 0...

  4. Suction Cup Induced Palatal Fistula: Surgical Closure by Palatal ...

    African Journals Online (AJOL)

    A break in the structural integrity of the palate leading to oro nasal communication is called palatal fistula,[1] which may be due to a genetic defect such as cleft lip and palate, an infection such as osteomyelitis or traumainduced by wearing a maxillary complete denture with a suction cup.[2] A suction cup because of its ...

  5. Cupping of the optic disk after methanol poisoning.

    Science.gov (United States)

    Galvez-Ruiz, Alberto; Elkhamary, Sahar M; Asghar, Nasira; Bosley, Thomas M

    2015-09-01

    To assess the frequency and significance of optic disk cupping after methanol poisoning. We retrospectively reviewed the medical records of 50 consecutive patients with methanol poisoning, including visual acuity, pupillary reaction, and optic disk features such as the presence and degree of cupping. All patients were examined in the chronic phase after optic nerve damage. Optic disk cupping ≥0.8 c/d was present in at least one eye of 22 of these 50 patients (43/100 eyes). Severity of cupping was statistically symmetric in the two eyes, and increasing severity of cupping was correlated with worse visual acuity (p=0.007) and increasing visual field loss. Degree of cupping was significantly correlated with increasing patient age but not with putaminal necrosis. Optic disk cupping after methanol poisoning may be more common than previously recognised. Cupping in this setting may reflect toxicity of methanol metabolites to axons and glial cells in the prelaminar, laminar and retrolaminar regions, and seems to be important as a marker for worse optic nerve damage. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  6. Wear numbers for ball cup and journal bearings

    NARCIS (Netherlands)

    Ligterink, D.J.; Moes, H.

    1980-01-01

    A wear number is defined for ball cup bearings and for journal bearings where the cup and the cylindrical bearing are made of soft material. This dimensionless wear number provides a relation between the following five quantities: the radius of the ball or the length of the journal bearing in

  7. Securing South Africa during the 2010 FIFA World Cup: Legacy ...

    African Journals Online (AJOL)

    Securing South Africa during the 2010 FIFA World Cup: Legacy implications for post-event safety and security. EC Perry, A Chunderduth, C Potgieter. Abstract. The trepidation over crime and safety concerns emerged as one of the main issues in relation to South Africa's hosting of the 2010 FIFA World Cup, prominent in the ...

  8. Adhesion strength of a living cell to various substrates measured using a cup-attached atomic force microscopy chip

    Science.gov (United States)

    Kim, Hyonchol; Ishibashi, Kenta; Matsuo, Kosuke; Kira, Atsushi; Onomura, Yui; Okada, Tomoko; Nakamura, Chikashi

    2018-03-01

    Cell adhesion strengths to various substrates were quantitatively measured using atomic force microscopy (AFM). A cup-shaped metal hemisphere was attached to the apex of the AFM cantilever, the “cup-chip” approached a cell (FP10SC2) to pick it up, the captured cell approached any one of six different substrates [gold (Au), nickel (Ni), bovine serum albumin (BSA), an amino group (NH2), poly(tetrafluoroethylene) (PTFE), and structured PTFE (sPTFE)], and the cell adhesion strength at the initial contact period was evaluated by detaching the cell from the substrate. The results obtained showed that the force needed to detach the cell from the NH2 substrate was more than 3-fold larger than that of metal substrates (Au and Ni), more than 15-fold larger than that of biochemically treated substrates (BSA), and more than 20-fold larger than that of hydrophobic substrates (PTFE and sPTFE). Using differences in adhesion strengths, a cell on a sPTFE substrate was picked up using a BSA-coated cup-chip, placed on a NH2 substrate, repeating this cell manipulation five times, and line patterning of cells was achieved. These results indicate that measurements of cell adhesion strength are fundamental to fabricate desired cell networks and the cup-chip is a useful tool for achieving easy cell manipulation.

  9. The Standardization of Bra Cup Measurements: Redefining Bra Sizing Language.

    Science.gov (United States)

    Bengtson, Bradley P; Glicksman, Caroline A

    2015-10-01

    There are many challenges in developing a standardized bra cup system, the most significant being that bra cup sizes are a continuum. Women's breasts occur as a fluid range of shapes, sizes, and volumes. Patients have specific expectations regarding bra cup size, and failure to achieve expectations remains the leading cause of patient dissatisfaction. Implant selection that determines eventual bra cup size is critical in patient education and management of patient expectations; however, this is not achievable until all speak the same bra cup language. Patient and surgeon perceptions may never be exact, but it is important to establish guidelines and standards to bridge this gap. Copyright © 2015 Elsevier Inc. All rights reserved.

  10. Can a cup anemometer 'underspeed'? A heretical question

    DEFF Research Database (Denmark)

    Kristensen, L.

    2002-01-01

    An analysis of cup-anemometer dynamics has been carried out in order to determine whether the mean-wind velocity can have a negative bias. This would be contrary to the general belief that cup anemometers always overspeed. Compared to prior analyses, the effect of a possible nonlinearity of the c......An analysis of cup-anemometer dynamics has been carried out in order to determine whether the mean-wind velocity can have a negative bias. This would be contrary to the general belief that cup anemometers always overspeed. Compared to prior analyses, the effect of a possible nonlinearity...... of the calibration function is included. The conclusion is that neither longitudinal nor lateral velocity fluctuations can contribute significantly to a negative bias. However, if a cup anemometer has an angular response that falls below the ideal cosine response, there will, as demonstrated in the concluding...

  11. Relationship between ultrasonic backscatter and trabecular thickness in human calcaneus: theory and experiment

    Science.gov (United States)

    Wear, Keith A.; Laib, Andres

    2003-05-01

    Trabecular thickness within cancellous bone is an important determinant of osteoporotic fracture risk. Noninvasive assessment of trabecular thickness could potentially yield useful diagnostic information. Faran's theory of elastic scattering from a cylindrical object immersed in a fluid has been employed to predict the dependence of ultrasonic backscatter on trabecular thickness. Methodology to test this theory has been validated in experiments using nylon fishing lines spanning a wide range of diameters. In the case of bone, Faran's theory predicts that, in the range of morphological and material properties expected for trabecular bone, the backscatter coefficient at 500 kHz should be approximately proportional to trabecular thickness to the power of 2.9. Experimental measurements of backscatter coefficient were performed on 43 human calcaneus samples in vitro. Mean trabecular thicknesses on the 43 samples were assessed using micro computed tomography. A power law fit to the data showed that the backscatter coefficient empirically varied as trabecular thickness to the 2.8 power. The 95% confidence interval for this exponent was 1.7 to 3.9. The square of the correlation coefficient for the linear regression to the log transformed data was 0.40. This suggests that 40% of variations in backscatter may be attributed to variations in trabecular thickness. These results (1) reinforce previous studies that offered validation for the Faran cylinder model for prediction of scattering properties of cancellous bone, and (2) provide added evidence for the potential diagnostic utility of the backscatter measurement.

  12. Effects of Immediate and Delayed Loading on Peri-Implant Trabecular Structures: A

    OpenAIRE

    Huang, Yan; Van Dessel, Jeroen; LIANG, Xin; Depypere, Maarten; Zhong, Weijian; Ma, Guowu; LAMBRICHTS, Ivo; Maes, Frederik; Jacobs, Reinhilde

    2013-01-01

    PURPOSE: To develop a method for characterizing trabecular bone microarchitecture using cone beam computed tomography (CBCT) and to evaluate trabecular bone changes after rehabilitation using immediate versus delayed implant protocols. MATERIALS AND METHODS: Six mongrel dogs randomly received 27 titanium implants in the maxillary incisor or mandibular premolar areas, following one of four protocols: (1) normal extraction socket healing; (2) immedia...

  13. Regional cortical and trabecular bone loss after spinal cord injury.

    Science.gov (United States)

    Dudley-Javoroski, Shauna; Shields, Richard K

    2012-01-01

    Spinal cord injury (SCI) triggers rapid loss of trabecular bone mineral density (BMD) in bone epiphyses and a loss of cortical cross-sectional area (CSA) in bone diaphyses, increasing fracture risk for people with SCI. The purpose of this study was to measure trabecular BMD and cortical CSA loss at several previously unexamined lower-limb sites (4% fibula, 12% femur, 86% tibia, cortical) in individuals with SCI. Using peripheral quantitative computed tomography, we scanned 13 participants with SCI longitudinally and 16 on one occasion; 21 participants without SCI served as controls. In the first year post-SCI, 15% to 35% of BMD was lost at the distal femur, proximal tibia, and distal fibula. Bone loss at the distal fibula accelerated between 1 and 2 years post-SCI. BMD at these sites reached a steady state value of ~50% of the non-SCI value 4 years post-SCI. At the tibia diaphysis, cortical CSA decline was slower, eventually reaching 65% of the non-SCI value. Because of the extensive loss of bone observed at these sites, careful consideration needs to be given to the dose of musculoskeletal stress delivered during rehabilitation interventions like standing, muscle electrical stimulation, and aggressive stretching of spastic muscles.

  14. Ultrastructural Changes in Human Trabecular Meshwork Tissue after Laser Trabeculoplasty

    Directory of Open Access Journals (Sweden)

    Jeffrey R. SooHoo

    2015-01-01

    Full Text Available Purpose. To compare morphologic changes in human trabecular meshwork (TM after selective laser trabeculoplasty (SLT and argon laser trabeculoplasty (ALT. Design. Laboratory evaluation of ex vivo human eye TM after laser trabeculoplasty. Methods. Corneoscleral rims from human cadaver eyes were sectioned and treated with varying powers of either SLT or ALT. Specimens were examined using light microscopy, scanning electron microscopy (SEM, and transmission electron microscopy (TEM. Results. TEM of SLT at all powers resulted in disrupted TM cells with cracked and extracellular pigment granules. SEM of SLT samples treated at high power revealed tissue destruction with scrolling of trabecular beams. SEM of ALT-treated tissue showed increasing destruction with exposure to higher power. The presence or absence of “champagne” bubbles during SLT did not alter the histologic findings. Conclusions. SLT-treated human TM revealed disruption of TM cells with cracked, extracellular pigment granules, particularly at higher treatment powers. Tissue scrolling was noted at very high SLT energy levels. ALT-treated tissue showed significant damage to both the superficial and deeper TM tissues in a dose-dependent fashion. Further studies are needed to guide titration of treatment power to maximize the IOP-lowering effect while minimizing both energy delivered and damage to target tissues.

  15. Relationship of bony trabecular characteristics and age to bone mass

    International Nuclear Information System (INIS)

    Choi, Dong Hoon; Song, Young Han; Yoon, Young Nam; Lee, Wan; Lee, Byung Do

    2006-01-01

    Bony strength is dependent on bone mass and bony structure. So this study was designed to investigate the relationship between the bone mass and bony mass and bony trabecular characteristics. Study subjects were 51 females (average age 68.6 years) and 20 males (average age 66.4 years). Bony mineral density (BMD, grams/cm 2 ) of proximal femur was measured by a dual energy X-ray absorptiometry (DEXA). Regions of interest (ROIs) were selected from the digitized radiographs of proximal femur. A customized computer program processed morphologic operations (MO) of ROIs. 44 skeletal variables of MO were calculated from ROIs on the Ward's triangle and greater trochanter of femur. WHO BMD classes were predicted by MO variables of the same ROI. Classification and Regression Tree analysis was used for calculating weighted kappa values, sensitivity and specificity of MO. The discriminating factors of morphologic operation were branch point, branch point [per cm sq]. Age also played important role in distinguishing osteoporotic classes. The sensitivity of MO at Ward's triangle and Greater Trochanter was 91.8%, 65.6%, respectively. The specificity of MO was 100% at Ward's triangle and Greater Trochanter. Bony trabecular characteristics obtained using radiological bone morphometric analysis seem to be related to bone mass

  16. Oxidative damage and autophagy in the human trabecular meshwork as related with ageing.

    Directory of Open Access Journals (Sweden)

    Alessandra Pulliero

    Full Text Available Autophagy is an intracellular lysosomal degradation process induced under stress conditions. Autophagy also plays a major role in ocular patho-physiology. Molecular aging does occur in the trabecular meshwork, the main regulator of aqueous humor outflow, and trabecular meshwork senescence is accompanied by increased oxidative stress. However, the role of autophagy in trabecular meshwork patho-physiology has not yet been examined in vivo in human ocular tissues. The purpose of the herein presented study is to evaluate autophagy occurrence in ex-vivo collected human trabecular meshwork specimens and to evaluate the relationship between autophagy, oxidative stress, and aging in this tissue. Fresh trabecular meshwork specimens were collected from 28 healthy corneal donors devoid of ocular pathologies and oxidative DNA damage, and LC3 and p62 protein expression analyzed. In a subset of 10 subjects, further to trabecular meshwork proteins, the amounts of cathepesin L and ubiquitin was analyzed by antibody microarray in aqueous humor. Obtained results demonstrate that autophagy activation, measured by LC3II/I ratio, is related with. oxidative damage occurrence during aging in human trabecular meshwork. The expression of autophagy marker p62 was lower in subjects older than 60 years as compared to younger subjects. These findings reflect the occurrence of an agedependent increase in the autophagy as occurring in the trabecular meshwork. Furthermore, we showed that aging promotes trabecular-meshwork senescence due to increased oxidative stress paralleled by autophagy increase. Indeed, both oxidative DNA damage and autophagy were more abundant in subjects older than 60 years. These findings shed new light on the role of oxidative damage and autophagy during trabecular-meshwork aging.

  17. File list: NoD.Oth.10.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available NoD.Oth.10.AllAg.Trabecular_meshwork_cells hg19 No description Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Oth.10.AllAg.Trabecular_meshwork_cells.bed ...

  18. File list: NoD.Oth.50.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available NoD.Oth.50.AllAg.Trabecular_meshwork_cells hg19 No description Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Oth.50.AllAg.Trabecular_meshwork_cells.bed ...

  19. File list: InP.Oth.05.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available InP.Oth.05.AllAg.Trabecular_meshwork_cells hg19 Input control Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Oth.05.AllAg.Trabecular_meshwork_cells.bed ...

  20. File list: NoD.Oth.05.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available NoD.Oth.05.AllAg.Trabecular_meshwork_cells hg19 No description Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Oth.05.AllAg.Trabecular_meshwork_cells.bed ...

  1. File list: InP.Oth.50.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available InP.Oth.50.AllAg.Trabecular_meshwork_cells hg19 Input control Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Oth.50.AllAg.Trabecular_meshwork_cells.bed ...

  2. File list: NoD.Oth.20.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available NoD.Oth.20.AllAg.Trabecular_meshwork_cells hg19 No description Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Oth.20.AllAg.Trabecular_meshwork_cells.bed ...

  3. File list: InP.Oth.20.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available InP.Oth.20.AllAg.Trabecular_meshwork_cells hg19 Input control Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Oth.20.AllAg.Trabecular_meshwork_cells.bed ...

  4. File list: InP.Oth.10.AllAg.Trabecular_meshwork_cells [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available InP.Oth.10.AllAg.Trabecular_meshwork_cells hg19 Input control Others Trabecular meshwork... cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/InP.Oth.10.AllAg.Trabecular_meshwork_cells.bed ...

  5. Blood metal ion concentrations in metal-on-metal total hip arthroplasty.

    Science.gov (United States)

    Ohtsuru, Tadahiko; Morita, Yuji; Murata, Yasuaki; Shimamoto, Shuji; Munakata, Yutaro; Kato, Yoshiharu

    2017-05-01

    The hip placement with a metal-on-metal (MOM) bearing has been used for both surface replacement and total hip arthroplasty (THA). Use of MOM bearing for hip replacement reduces the wear compared to conventional bearings. We prospectively assessed 30 patients who underwent unilateral MOM THA. A control group of 30 patients who underwent metal-on-polyethylene THA using the implants as the other group, except for bearing, were accessed. Blood samples were collected preoperatively and at 3- , 6- , 9- , 12- , 15- , 18- , and 24-month intervals. Changes in mean blood metal ion concentration were compared between the MOM and metal-on-polyethylene groups. A statistically significant positive correlation was observed between blood cobalt and chromium concentrations in all of the patients. The mean blood ion concentrations of the MOM were significantly higher than those of the metal-on-polyethylene. A statistically significant negative correlation was found between maximum blood cobalt concentration and cup version angle. The maximum blood chromium concentrations in the patients who had larger cup version angles were more likely to decrease. We considered that cup version angle is one of the factors that have the greatest effect on blood metal ion concentration, and the target cup version angle that did not induce an increase in blood metal ion concentrations was approximately 20°.

  6. Distance constant of the Risø cup anemometer

    DEFF Research Database (Denmark)

    Kristensen, L.; Frost Hansen, O.

    2002-01-01

    The theory for cup-anemometer dynamics is presented in some detail and two methods of obtaining the distance constant lo are discussed. The first method is based on wind tunnel measurements: with a constant wind speed the cup anemometer is released from alocked position of the rotor...... and the increasing rotation rate recorded. It is concluded that the rapid increase in rotation rate makes the method very inaccurate. The second method consists of an analysis of turbulent, atmospheric of wind speed asmeasured by the cup anemometer and a fast-responding sonic anemometer with a spatial eddy...

  7. RoboCup rescue : development of inteligent cooperative agents

    OpenAIRE

    Alves, Pedro César Fonseca Gonçalves

    2008-01-01

    O trabalho desenvolvido nesta dissertação tem como tema o desenvolvimento de um agente inteligente com coordenação e comunicação no ambiente RoboCup Rescue. No RoboCup Rescue existem seis tipos de agentes, no entanto nesta tese só dois agentes foram desenvolvidos, especificamente o tipo de agentes Ambulâncias e Centros de Ambulâncias. O tipo de agente Ambulância é o elemento responsável pelo salvamento de civis na cidade virtual que constitui o ambiente RoboCup Rescue. Para cumprir essa ta...

  8. A review of trabecular bone functional adaptation: what have we learned from trabecular analyses in extant hominoids and what can we apply to fossils?

    Science.gov (United States)

    Kivell, Tracy L

    2016-04-01

    Many of the unresolved debates in palaeoanthropology regarding evolution of particular locomotor or manipulative behaviours are founded in differing opinions about the functional significance of the preserved external fossil morphology. However, the plasticity of internal bone morphology, and particularly trabecular bone, allowing it to respond to mechanical loading during life means that it can reveal greater insight into how a bone or joint was used during an individual's lifetime. Analyses of trabecular bone have been commonplace for several decades in a human clinical context. In contrast, the study of trabecular bone as a method for reconstructing joint position, joint loading and ultimately behaviour in extant and fossil non-human primates is comparatively new. Since the initial 2D studies in the late 1970s and 3D analyses in the 1990 s, the utility of trabecular bone to reconstruct behaviour in primates has grown to incorporate experimental studies, expanded taxonomic samples and skeletal elements, and improved methodologies. However, this work, in conjunction with research on humans and non-primate mammals, has also revealed the substantial complexity inherent in making functional inferences from variation in trabecular architecture. This review addresses the current understanding of trabecular bone functional adaptation, how it has been applied to hominoids, as well as other primates and, ultimately, how this can be used to better interpret fossil hominoid and hominin morphology. Because the fossil record constrains us to interpreting function largely from bony morphology alone, and typically from isolated bones, analyses of trabecular structure, ideally in conjunction with that of cortical structure and external morphology, can offer the best resource for reconstructing behaviour in the past. © 2016 Anatomical Society.

  9. Mapping trabecular disconnection "hotspots" in aged human spine and hip.

    Science.gov (United States)

    Aaron, Jean E; Shore, Patricia A; Itoda, Mizuo; Morrison, Rory J M; Hartopp, Andrew; Hensor, Elizabeth M A; Hordon, Lesley D

    2015-09-01

    Trabecular bone disconnection is an independent factor in age-related skeletal failure where real termini (ReTm; rare in youth) may cause weakness disproportionate to tissue loss, yet their structural contribution at vulnerable locations remains uncertain. ReTm (previously recorded at the iliac crest) were mapped in "normal" aged vertebral bodies (T11-L5 autopsy; 20 females, 10 males) and corresponding proximal femora (autopsy; 10 females). Results were compared with biomechanically failed femora from orthopaedic subjects aged >58 yr (osteoporosis OP, 10 females; osteoarthritis OA, 10 females). A novel direct 2D/3D histological method was applied to large, thick (300 μm) slices superficially silver-stained to separate ReTm (unstained) from apparent termini (planar artefacts, brown). Light microscope field co-ordinates enabled ReTm mapping and statistical testing relative to i) sex, ii) tissue sector and iii) slicing plane. In men ReTm populations were small and random while in women they were large and sector-specific. In vertebrae they clustered anterior/superior being rare posterior/inferior; in the femoral head they concentrated distal/superior and also near the fovea, being fewer distal/inferior. A distribution polarity was evident with 100% more ReTm observed transversely (i.e., on tensile-related cross struts) than longitudinally (i.e., on compression-related vertical struts). Their numbers rose in OP (BV/TV14%), remaining polarised and sector-specific in OP only. Comparative experimentation by marrow elution of an OP animal model demonstrated "floating segments" as a possible outcome. Conclusions were supported statistically that trabecular disconnection "hotspots" at vulnerable locations are sex- and sector-specific, mainly transaxial, and subject to disease modulation. Copyright © 2015. Published by Elsevier Inc.

  10. Structural and functional characterization of Pseudomonas aeruginosa CupB chaperones.

    Directory of Open Access Journals (Sweden)

    Xun Cai

    Full Text Available Pseudomonas aeruginosa, an important human pathogen, is estimated to be responsible for ∼10% of nosocomial infections worldwide. The pathogenesis of P. aeruginosa starts from its colonization in the damaged tissue or medical devices (e.g. catheters, prothesis and implanted heart valve etc. facilitated by several extracellular adhesive factors including fimbrial pili. Several clusters containing fimbrial genes have been previously identified on the P. aeruginosa chromosome and named cup[1]. The assembly of the CupB pili is thought to be coordinated by two chaperones, CupB2 and CupB4. However, due to the lack of structural and biochemical data, their chaperone activities remain speculative. In this study, we report the 2.5 Å crystal structure of P. aeruginosa CupB2. Based on the structure, we further tested the binding specificity of CupB2 and CupB4 towards CupB1 (the presumed major pilus subunit and CupB6 (the putative adhesin using limited trypsin digestion and strep-tactin pull-down assay. The structural and biochemical data suggest that CupB2 and CupB4 might play different, but not redundant, roles in CupB secretion. CupB2 is likely to be the chaperone of CupB1, and CupB4 could be the chaperone of CupB4:CupB5:CupB6, in which the interaction of CupB4 and CupB6 might be mediated via CupB5.

  11. Genetic Dissection of Trabecular Bone Structure with Mouse Intersubspecific Consomic Strains

    Directory of Open Access Journals (Sweden)

    Taro Kataoka

    2017-10-01

    Full Text Available Trabecular bone structure has an important influence on bone strength, but little is known about its genetic regulation. To elucidate the genetic factor(s regulating trabecular bone structure, we compared the trabecular bone structures of two genetically remote mouse strains, C57BL/6J and Japanese wild mouse-derived MSM/Ms. Phenotyping by X-ray micro-CT revealed that MSM/Ms has structurally more fragile trabecular bone than C57BL/6J. Toward identification of genetic determinants for the difference in fragility of trabecular bone between the two mouse strains, we employed phenotype screening of consomic mouse strains in which each C57BL/6J chromosome is substituted by its counterpart from MSM/Ms. The results showed that many chromosomes affect trabecular bone structure, and that the consomic strain B6-Chr15MSM, carrying MSM/Ms-derived chromosome 15 (Chr15, has the lowest values for the parameters BV/TV, Tb.N, and Conn.D, and the highest values for the parameters Tb.Sp and SMI. Subsequent phenotyping of subconsomic strains for Chr15 mapped four novel trabecular bone structure-related QTL (Tbsq1-4 on mouse Chr15. These results collectively indicate that genetic regulation of trabecular bone structure is highly complex, and that even in the single Chr15, the combined action of the four Tbsqs controls the fragility of trabecular bone. Given that Tbsq4 is syntenic to human Chr 12q12-13.3, where several bone-related SNPs are assigned, further study of Tbsq4 should facilitate our understanding of the genetic regulation of bone formation in humans.

  12. Insight into the 3D-trabecular architecture of the human patella.

    Science.gov (United States)

    Hoechel, Sebastian; Schulz, Georg; Müller-Gerbl, Magdalena

    2015-07-01

    The subchondral bone plate (SBP), a dynamic component of the osteochondral unit, shows functional adaptation to long-term loading by distribution of the mineral content in a manner best serving the mechanical demands. Since the received joint-load is transmitted into the trabecular system, the spongy bone also exhibits differences in strain energy density which models it for optimal support. To evaluate the regional variations in trabecular architecture, in accordance with the density distribution of the SBP revealing its long-term load intake, CT- and μCT-datasets of ten physiologic patellae were analysed for defined parameters of bony structure. For the SBP, the density distributions as well as area measurements were used. The trabecular architecture was described using parameters of bone morphology comprising the first 5mm (examined in 1mm steps) below the SBP. The obtained measurements are: Bone volume fraction (BV/TV); Bone surface density (BS/TV); Trabecular number (Tb.N); Trabecular separation (Tb.Sp); Trabecular thickness (Tb.Th); structure model index (SMI); and the Degree of anisotropy (DA). The evaluated architectural parameters varied within the trabecular system and showed an inhomogeneous distribution pattern. It proved to be distinctive with maxima of material and stability situated below areas of the highest long-term load intake. With increasing depth, the pattern of distribution was persistent but lessened in intensity. The parameters significantly correlated with the density distribution of the SBP within the first and second millimetres. With increasing depth down to the fifth millimetre, the coefficients of correlation decreased for all values. The trabecular network adapts to its mechanical needs and is therefore not homogenously built. Dependent upon the long-term load intake, the trabecular model optimizes the support with significant correlation to the density distribution of the SBP. Copyright © 2015 Elsevier GmbH. All rights reserved.

  13. Patterns of activity adaptation in humeral trabecular bone in Neolithic humans and present-day people.

    Science.gov (United States)

    Scherf, Heike; Wahl, Joachim; Hublin, Jean-Jacques; Harvati, Katerina

    2016-01-01

    The annual turnover rate of trabecular bone by far exceeds that of cortical bone and, therefore, is very sensitive to its daily loading regime. Here we test the hypothesis that the study of the trabecular bone architecture of the human humerus is able to differentiate between different habitual manual activities. For this purpose, we compared the trabecular architecture of the humeral head in a Neolithic population to that of a sample of contemporary Europeans using micro-computed tomography (microCT). We defined in each specimen a spherical volume of interest with a diameter of 57.5 ± 2.5% of the maximal diameter of the humeral head to metrically analyze the bulk of humeral head trabecular architecture. We subsequently quantified the trabecular architectures in the VOIs, measuring seven standard 3D-morphometric parameters, and used univariate and multivariate statistical analyses for comparisons within and between populations. Univariate statistical analysis showed significant differences in a combination of 3D-morphometric parameters. A principal components analysis of the 3D-morphometrics of the trabecular architectures separated the Neolithic from the contemporary samples on the basis of differences in their gross trabecular architecture, including differences in the bone volume fraction (BV/TV), the number of trabeculae per unit length (Tb N), and the distance between trabeculae (Tb Sp). We interpret the significant differences found in the humeral trabecular bone of the Neolithic and the contemporary group as likely reflecting the distinct manual working routines. The trabecular bone configuration in the Neolithic sample shows presumably functional signatures of prehistoric subsistence techniques and activity levels. © 2015 Wiley Periodicals, Inc.

  14. Influence of small-scale turbulence on cup anemometer calibrations

    Science.gov (United States)

    Marraccini, M.; Bak-Kristensen, K.; Horn, A.; Fifield, E.; Hansen, S. O.

    2017-11-01

    The paper presents and discusses the calibration results of cup anemometers under different levels of small-scale turbulence. Small-scale turbulence is known to govern the curvature of shear layers around structures and is not related to the traditional under and over speeding of cup anemometers originating from large-scale turbulence components. The paper has shown that the small-scale turbulence has a significant effect on the calibration results obtained for cup anemometers. At 10m/s the rotational speed seems to change by approx. 0.5% due to different simulations of the small-scale turbulence. The work which this paper is based on, is part of the TrueWind research project, aiming to increase accuracy of mast top-mounted cup anemometer measurements.

  15. Prevalence of disc cupping in non-glaucomatous eyes

    Directory of Open Access Journals (Sweden)

    José Pablo Chiappe

    2015-02-01

    Full Text Available This study assessed optic disc size and cupping, using a commercially available ophthalmoscope, in order to show norms of these values for clinical practice. Subjects were office-workers referred from their respective workplaces for a routine medical examination, which included eye examination. The optic disc size was classified as small, medium or large, for having a diameter 1.5 times (respectively the diameter of the ophthalmoscope's selected light spot on the posterior pole. The cupping was classified as the ratio of the vertical cupping diameter and the vertical disc diameter on a relative decimal scale from 0.0 to 1.0.This study included 184 subjects with a mean age of 40.5 ± 9.5 years; 149 (81% were males. Their mean ocular pressure was 12.4 ± 1.5 mmHg (range 10-17 mmHg. There was a high correlation between optic disc sizes and cupping in the right and left eyes (Pearson Correlation r = 0.866, p < 0.001; therefore, for simplicity only the data for right eyes are presented. According to our definition, the optic discs in these eyes comprised 27 (14.7% small, 141 (76.6% medium and 16 (8.7% large. The small optic discs were rarely cupped, and the large optic discs were always cupped. Optic disc cupping greater than 0.7 was rarely found and should be suspect of glaucoma. Clinical doctors should be aware of this and refer those subjects with abnormal cupping to the specialist.

  16. Management and marketing of sporting events: Nike Premier Cup Project

    OpenAIRE

    Nedbal, Jakub

    2008-01-01

    Title: Management and marketing ofsporting events: Nike Premier Cup project Points of thesis: Publish the Nike Premier Cup promotion campaign project and point out improvement possibilities for upcoming years based on analysis ofpast and present state. Methods: Data will be obtained by interview, observation, description analysis and SWOT analysis Results: Promotion campaign, improvement possibilities, final day schedule Keywords: SWOT analysis, promotion, management, marketing, Nike Premier ...

  17. Manipulating Tournaments in Cup and Round Robin Competitions

    OpenAIRE

    Russell, Tyrel; Walsh, Toby

    2009-01-01

    In sports competitions, teams can manipulate the result by, for instance, throwing games. We show that we can decide how to manipulate round robin and cup competitions, two of the most popular types of sporting competitions in polynomial time. In addition, we show that finding the minimal number of games that need to be thrown to manipulate the result can also be determined in polynomial time. Finally, we show that there are several different variations of standard cup competitions where mani...

  18. Distance constant of the Risø cup anemometer

    OpenAIRE

    Kristensen, L.; Frost Hansen, O.

    2002-01-01

    The theory for cup-anemometer dynamics is presented in some detail and two methods of obtaining the distance constant lo are discussed. The first method is based on wind tunnel measurements: with a constant wind speed the cup anemometer is released from alocked position of the rotor and the increasing rotation rate recorded. It is concluded that the rapid increase in rotation rate makes the method very inaccurate. The second method consists of an analysis of turbulent, atmospheric of wind spe...

  19. Proteomic effects of wet cupping (Al-hijamah

    Directory of Open Access Journals (Sweden)

    Amer A. Almaiman

    2018-01-01

    Full Text Available Wet cupping (Al-hijamah is a therapeutic technique practiced worldwide as a part of the Unani system of medicine. It involves bloodletting from acupoints on a patient’s skin to produce a therapeutic outcome. A thorough review of research articles on wet cupping with relevance to proteomics field that are indexed by Google Scholar, PubMed, and/or Science Direct databases was performed. Eight original research articles were summarized in this paper. Overall, wet cupping did not have a significant effect on C-reactive protein, Hsp-27, sister chromatid exchanges, and cell replication index. In contrast, wet cupping was found to produce higher oxygen saturation, eliminate lactate from subcutaneous tissues, remove blood containing higher levels of malondialdehyde and nitric oxide, and produce higher activity of myeloperoxidase. The proteomic effects of wet cupping therapy have not been adequately investigated. Thus, future studies on wet cupping that use systemic and sound protocols to avoid bias should be conducted.

  20. Medullary carcinoma of the thyroid - an unusual case of hyalinizing trabecular adenoma - like variant (encapsulated

    Directory of Open Access Journals (Sweden)

    Madhusmita Jena

    2012-07-01

    Full Text Available Medullary thyroid carcinoma is a neoplasm occurring in sporadic and familial patterns. A rare variant of medullary thyroid carcinoma shows microscopic features similar to hyalinizing trabecular adenoma of thyroid. Detection of this variant requires a high index of suspicion and immunohistochemical confirmation by calcitonin positivity. We present a 36 years old female patient with a thyroid nodule, which, on microscopy, displayed an encapsulated tumor with elongated cells arranged in trabecular pattern separated by hyalinized fibrous septae simulating a hyalinizing trabecular adenoma. Also present were spindle cells arranged in an organoid fashion. Most of the cells showed salt and pepper chromatin pattern. The lesion was negative for amyloid but showed diffuse calcitonin positivity indicative of a tumor of C-cell origin i.e. medullary carcinoma of thyroid – hyalinizing trabecular variant.

  1. Age variations in the properties of human tibial trabecular bone and cartilage

    DEFF Research Database (Denmark)

    Ding, Ming

    2000-01-01

    is parallel to the longitudinal loading axis of the tibia. The mechanical properties of the normal cartilage and bone vary with age and respond simultaneously to mechanical loading. Both cartilage and bone in early-stage OA are mechanically inferior to normal, and OA cartilage and bone have lost their unit......Initiated and motivated by clinical and scientific problems such as age-related bone fracture, prosthetic loosening, bone remodeling, and degenerative bone diseases, much significant research on the properties of trabecular bone has been carried out over the last two decades. This work has mainly...... focused on the central vertebral trabecular bone, while little is known about age-related changes in the properties of human peripheral (tibial) trabecular bone. Knowledge of the properties of peripheral (tibial) trabecular bone is of major importance for the understanding of degenerative diseases...

  2. Decreased trabecular bone biomechanical competence, apparent density, IGF-II and IGFBP-5 content in acromegaly

    DEFF Research Database (Denmark)

    Ueland, Thor; Ebbesen, Ebbe Nils; Thomsen, Jesper Skovhus

    2002-01-01

    BACKGROUND: Earlier studies on the effect of excess growth hormone (GH) on trabecular bone have been conflicting. Since insulin-like growth factors (IGFs) and their binding proteins (IGFBPs) in part mediate the effects of GH, the present study aimed to investigate trabecular bone composition...... of these growth factors in relation to biomechanical properties in acromegaly. MATERIALS AND METHODS: Trabecular bone biomechanical competence (compression test), apparent density (peripheral quantitative computed tomography, pQCT), and bone matrix contents of calcium (HCl hydrolysis) and IGFs (guanidinium......-HCl extraction) were measured in iliac crest biopsies from 13 patients with active acromegaly (two women and 11 men, aged 21-61 years) and 21 age- and sex-matched controls (four women and 17 men, aged 23-64 years). RESULTS: Trabecular bone pQCT was reduced in acromegalic patients compared with controls (P = 0...

  3. Effects of chitosan oligosaccharides on the femur trabecular structure in ovariectomized rats

    International Nuclear Information System (INIS)

    Iwata, Hiroshi; Yana, Seiji; Yosue, Takashi; Nasu, Masanori

    2005-01-01

    Drugs used to treat osteoporosis are taken long-term and ideally have no adverse effects. Recent interest has focused on chitosan oligosaccharides as a bone-inducing substance for use as bone graft material. The present study was designed to investigate the effects of chitosan oligosaccharides on the femur trabecular structure in ovariectomized rats by three-dimensional imaging analysis using micro-computed tomography (CT). Female 12-week-old Wistar rats were divided into three groups, which underwent ovariectomy (two groups) or sham surgery (one group). After 12 weeks, rats of one of the ovariectomized groups began treatment with chitosan oligosaccharides (500 mg/kg bodyweight) three times per week for 8 weeks. Then, the femurs of all rats were resected for bone analysis by micro-CT, and three-dimensional images of the femur were reconstructed from the axial CT images to evaluate the following parameters: bone volume tissue volume (BV/TV), trabecular thickness (Tb.Th), trabecular number (Tb.N), trabecular separation (Tb.sp), trabecular bone pattern factor (TBPf), structure model index (SMI), number of nodes per unit tissue volume, number of termini per unit tissue volume, and the total strut length per unit tissue volume. The BV/TV, Tb.Th, and Tb.N were significantly higher in the ovariectomized and treated (OVX+C) group versus the ovariectomized, untreated (OVX) group. Tb.Sp, TBPf, and SMI were significantly lower in the OVX+C group versus the OVX group. Our findings demonstrate that chitosan oligosaccharides prevent decreases in bone volume, trabecular number, trabecular thickness, and trabecular connectivity in the femurs of ovariectomized rats. (author)

  4. Attenuating trabecular morphology associated with low magnesium diet evaluated using micro computed tomography.

    Directory of Open Access Journals (Sweden)

    Shu-Ju Tu

    Full Text Available The literature shows that bone mineral density (BMD and the geometric architecture of trabecular bone in the femur may be affected by inadequate dietary intake of Mg. In this study, we used microcomputed tomography (micro-CT to characterize and quantify the impact of a low-Mg diet on femoral trabecular bones in mice.Four-week-old C57BL/6J male mice were randomly assigned to 2 groups and supplied either a normal or low-Mg diet for 8weeks. Samples of plasma and urine were collected for biochemical analysis, and femur tissues were removed for micro-CT imaging. In addition to considering standard parameters, we regarded trabecular bone as a cylindrical rod and used computational algorithms for a technical assessment of the morphological characteristics of the bones. BMD (mg-HA/cm3 was obtained using a standard phantom.We observed a decline in the total tissue volume, bone volume, percent bone volume, fractal dimension, number of trabecular segments, number of connecting nodes, bone mineral content (mg-HA, and BMD, as well as an increase in the structural model index and surface-area-to-volume ratio in low-Mg mice. Subsequently, we examined the distributions of the trabecular segment length and radius, and a series of specific local maximums were identified. The biochemical analysis revealed a 43% (96% decrease in Mg and a 40% (71% decrease in Ca in plasma (urine excretion.This technical assessment performed using micro-CT revealed a lower population of femoral trabecular bones and a decrease in BMD at the distal metaphysis in the low-Mg mice. Examining the distributions of the length and radius of trabecular segments showed that the average length and radius of the trabecular segments in low-Mg mice are similar to those in normal mice.

  5. Attenuating trabecular morphology associated with low magnesium diet evaluated using micro computed tomography.

    Science.gov (United States)

    Tu, Shu-Ju; Wang, Shun-Ping; Cheng, Fu-Chou; Weng, Chia-En; Huang, Wei-Tzu; Chang, Wei-Jeng; Chen, Ying-Ju

    2017-01-01

    The literature shows that bone mineral density (BMD) and the geometric architecture of trabecular bone in the femur may be affected by inadequate dietary intake of Mg. In this study, we used microcomputed tomography (micro-CT) to characterize and quantify the impact of a low-Mg diet on femoral trabecular bones in mice. Four-week-old C57BL/6J male mice were randomly assigned to 2 groups and supplied either a normal or low-Mg diet for 8weeks. Samples of plasma and urine were collected for biochemical analysis, and femur tissues were removed for micro-CT imaging. In addition to considering standard parameters, we regarded trabecular bone as a cylindrical rod and used computational algorithms for a technical assessment of the morphological characteristics of the bones. BMD (mg-HA/cm3) was obtained using a standard phantom. We observed a decline in the total tissue volume, bone volume, percent bone volume, fractal dimension, number of trabecular segments, number of connecting nodes, bone mineral content (mg-HA), and BMD, as well as an increase in the structural model index and surface-area-to-volume ratio in low-Mg mice. Subsequently, we examined the distributions of the trabecular segment length and radius, and a series of specific local maximums were identified. The biochemical analysis revealed a 43% (96%) decrease in Mg and a 40% (71%) decrease in Ca in plasma (urine excretion). This technical assessment performed using micro-CT revealed a lower population of femoral trabecular bones and a decrease in BMD at the distal metaphysis in the low-Mg mice. Examining the distributions of the length and radius of trabecular segments showed that the average length and radius of the trabecular segments in low-Mg mice are similar to those in normal mice.

  6. Preliminary study of slow and fast ultrasonic waves using MR images of trabecular bone phantom

    Science.gov (United States)

    Solis-Najera, S. E.; Neria-Pérez, J. A.; Medina, L.; Garipov, R.; Rodríguez, A. O.

    2014-11-01

    Cancellous bone is a complex tissue that performs physiological and biomechanical functions in all vertebrates. It is made up of trabeculae that, from a simplified structural viewpoint, can be considered as plates and beams in a hyperstatic structure that change with time leading to osteoporosis. Several methods has been developed to study the trabecular bone microstructure among them is the Biot's model which predicts the existence of two longitudinal waves in porous media; the slow and the fast waves, that can be related to porosity of the media. This paper is focused on the experimental detection of the two Biot's waves of a trabecular bone phantom, consisting of a trabecular network of inorganic hydroxyapatite. Experimental measurements of both waves were performed using through transmission ultrasound. Results had shown clearly that the propagation of two waves propagation is transversal to the trabecular alignment. Otherwise the waves are overlapped and a single wave seems to be propagated. To validate these results, magnetic resonance images were acquired to assess the trabecular direction, and to assure that the pulses correspond to the slow and fast waves. This approach offers a methodology for non-invasive studies of trabecular bones.

  7. Preliminary study of slow and fast ultrasonic waves using MR images of trabecular bone phantom

    Energy Technology Data Exchange (ETDEWEB)

    Solis-Najera, S. E., E-mail: solisnajera@ciencias.unam.mx, E-mail: angel.perez@ciencias.unam.mx, E-mail: lucia.medina@ciencias.unam.mx; Neria-Pérez, J. A., E-mail: solisnajera@ciencias.unam.mx, E-mail: angel.perez@ciencias.unam.mx, E-mail: lucia.medina@ciencias.unam.mx; Medina, L., E-mail: solisnajera@ciencias.unam.mx, E-mail: angel.perez@ciencias.unam.mx, E-mail: lucia.medina@ciencias.unam.mx [Facultad de Ciencias, Universidad Nacional Autónoma de México, México, DF 04510 (Mexico); Garipov, R., E-mail: ruslan.garipov@mrsolutions.co.uk [MR Solutions Ltd, Surrey (United Kingdom); Rodríguez, A. O., E-mail: arog@xanum.uam.mx [Departamento Ingeniería Eléctrica, Universidad Autónoma Metropolitana Iztapalapa, México, DF 09340 (Mexico)

    2014-11-07

    Cancellous bone is a complex tissue that performs physiological and biomechanical functions in all vertebrates. It is made up of trabeculae that, from a simplified structural viewpoint, can be considered as plates and beams in a hyperstatic structure that change with time leading to osteoporosis. Several methods has been developed to study the trabecular bone microstructure among them is the Biot’s model which predicts the existence of two longitudinal waves in porous media; the slow and the fast waves, that can be related to porosity of the media. This paper is focused on the experimental detection of the two Biot’s waves of a trabecular bone phantom, consisting of a trabecular network of inorganic hydroxyapatite. Experimental measurements of both waves were performed using through transmission ultrasound. Results had shown clearly that the propagation of two waves propagation is transversal to the trabecular alignment. Otherwise the waves are overlapped and a single wave seems to be propagated. To validate these results, magnetic resonance images were acquired to assess the trabecular direction, and to assure that the pulses correspond to the slow and fast waves. This approach offers a methodology for non-invasive studies of trabecular bones.

  8. Anti- Versus Pro-Inflammatory Metabololipidome Upon Cupping Treatment

    Directory of Open Access Journals (Sweden)

    Qi Zhang

    2018-02-01

    Full Text Available Background/Aims: This study aimed to explore the metabololipidome in mice upon cupping treatment. Methods: A nude mouse model mimicking the cupping treatment in humans was established by administrating four cupping sets on the back skin for 15 minutes. UPLC-MS/ MS was performed to determine the PUFA metabolome in mice skin and blood before and after cupping treatment. The significantly changed lipids were administered in macrophages to assess the production of pro-inflammatory cytokines IL-6 and TNF-α by ELISA. Results: The anti-inflammatory lipids, e.g. PGE1, 5,6-EET, 14,15-EET, 10S,17S-DiHDoHE, 17R-RvD1, RvD5 and 14S-HDoHE were significantly increased while pro-inflammatory lipids, e.g. 12-HETE and TXB2 were deceased in the skin or plasma post cupping treatment. Cupping treatment reversed the LPS-stimulated IL-6 and TNF-α expression in mouse peritoneal exudates. Moreover, 5,6-EET, PGE1 decreased the level of TNF-α, while 5,6-EET, 5,6-DHET downregulated IL-6 production in macrophages. Importantly, 14,15-EET and 14S-HDoHE inhibited both IL-6 and TNF-α induced by lipopolysaccharide (LPS. 17-RvD1, RvD5 and PGE1 significantly reduced the LPS-initiated TNF-α, while TXB2 and 12-HETE further upregulated the LPS-enhanced IL-6 and TNF-α expression in macrophages. Conclusion: Our results reveal the identities of anti-inflammatory versus pro-inflammatory metabolipidome and suggest the potential therapeutic mechanism of cupping treatment.

  9. Rutting resistance of asphalt mixture with cup lumps modified binder

    Science.gov (United States)

    Shaffie, E.; Hanif, W. M. M. Wan; Arshad, A. K.; Hashim, W.

    2017-11-01

    Rutting is the most common pavement distress in pavement structures which occurs mainly due to several factors such as increasing of traffic volume, climatic conditions and also due to construction design errors. This failure reduced the service life of the pavement, reduced driver safety and increase cost of maintenance. Polymer Modified Binder has been observed for a long time in improving asphalt pavement performance. Research shows that the use of polymer in bituminous mix not only improve the resistance to rutting but also increase the life span of the pavement. This research evaluates the physical properties and rutting performance of dense graded Superpave-designed HMA mix. Two different types of dense graded Superpave HMA mix were developed consists of unmodified binder mix (UMB) and cup lumps rubber (liquid form) modified binder mix (CLMB). Natural rubber polymer modified binder was prepared from addition of 8 percent of cup lumps into binder. Results showed that all the mixes passed the Superpave volumetric properties criteria which indicate that these mixtures were good with respect to durability and flexibility. Furthermore, rutting results from APA rutting test was determined to evaluate the performance of these mixtures. The rutting result of CLMB demonstrates better resistance to rutting than those prepared using UMB mix. Addition of cup lumps rubber in asphalt mixture was found to be significant, where the cup lumps rubber has certainly improves the binder properties and enhanced its rutting resistance due to greater elasticity offered by the cup lumps rubber particles. It shows that the use of cup lumps rubber can significantly reduce the rut depth of asphalt mixture by 41% compared to the minimum rut depth obtained for the UMB mix. Therefore, it can be concluded that the cup lumps rubber is suitable to be used as a modifier to modified binder in order to enhance the properties of the binder and thus improves the performance of asphalt mixes.

  10. Musik sebagai Wujud Eksistensi dalam Gelaran World Cup

    Directory of Open Access Journals (Sweden)

    Michael HB Raditya

    2014-11-01

    Full Text Available We Are One atau “Ole Ola” merupakan lagu resmi dari gelaran World Cup. Setiap World Cupmempunyai lagu resminya ditiap gelarannya. Dalam keberlangsungannya, setiap lagu world cupmembutuhkan pertimbangan dalam pembentukannya. Aspek-aspek seperti budaya, sosial, politikdan lainya menjadi alasan penting dalam pembentukannya. Pembentukan Ole Ola didasarkan padaproses hibriditas budaya lokal dan global. Perpaduan samba dan hip hop menjadi variant dalampembentukannya. Perpaduan tersebut membentuk identitas untuk lagu itu sendiri, dan untuk gelaranworld cup. Eksistensi dari lagu sehingga makin terasa karena perpaduan yang membentuk identitas.Terlebih lagu tersebut tercipta tidak hanya karena gelaran, tetapi mempunyai fungsi dan guna untukmasyarakat. Musik sebagai media dalam mengkonstruksi pesan atas kepentingan. Musik membentukidentitas, dan mempunyai eksistensi dalam keberlangsungannya. Musik tidak lagi hanya berfungsisebagai musik saja, tetapi musik mempunyai peran dalam pembentukan identitas dan menjamineksistensi. Music as a form of Existance in the World Cup Performance. We are one or Ole Ola is the officialsong of the world cup performance. Every world cup has its official song in each event. In its development ofexistance, every song in world cup needs requires of consideration for creating process. Aspects such as cultural,social, politics and others become the important reason for creation. The creating proses of Ole Ola song isbased on the local and global cultural hybridity. The combination of samba and hip hop is a primary varianton creating process. The combination creates an identity for the song itself, and for world cup identity. Theexistance of Ole Ola is stronger because the combination may create the new identity. Moreover, the songcreated is not only for the event, but also has a function and purpose to society. Music is as a medium inconstructing the messages of interest. Music creates an identity, and has an existance in its

  11. New is the well-forgotten old: The use of dry cupping in musculoskeletal medicine.

    Science.gov (United States)

    Rozenfeld, Evgeni; Kalichman, Leonid

    2016-01-01

    Cupping is an ancient technique used in treating pain and various disorders. Different techniques have been developed over time, however, applying a cup to create suction over a painful area, is common to all. Dry or fire cupping, used on the intact skin, leaves bluish circular hematomas. Recently, interest in cupping has re-emerged and subsequently, several studies have begun to investigate the mechanisms of cupping therapy. Mechanically, cupping increases blood circulation, whereas physiologically it activates the immune system and stimulates the mechanosensitive fibers, thus leading to a reduction in pain. There is initial scientific evidence that dry cupping is able to reduce musculoskeletal pain. Since cupping is an inexpensive, noninvasive and low-risk (if performed by a trained practitioner) therapeutic modality, we believe that it should be included in the arsenal of musculoskeletal medicine. It is essential to perform additional studies clarifying the biological mechanism and clinical effects of cupping. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Multiphoton gonioscopy to image the trabecular meshwork of porcine eyes

    Science.gov (United States)

    Masihzadeh, Omid; Ammar, David A.; Kahook, Malik Y.; Gibson, Emily A.; Lei, Tim C.

    2013-03-01

    The aqueous outflow system (AOS), including the trabecular meshwork (TM), the collector channels (CC) and the Schlemm's canal (SC), regulates intraocular pressure (IOP) through the drainage of the aqueous humor (AH). Abnormal IOP elevation leads to increased pressure stress to retinal ganglion cells, resulting in cell loss that can ultimately lead to complete loss of eyesight. Therefore, development of imaging tools to detect abnormal structural and functional changes of the AOS is important in early diagnosis and prevention of glaucoma. Multiphoton microscopy (MPM), including twophoton autofluorescence (TPAF) and second harmonic generation (SHG), is a label-free microscopic technique that allows molecular specific imaging of biological tissues like the TM. Since the TM and other AOS structures are located behind the highly scattering scleral tissue, transscleral imaging of the TM does not provide enough optical resolution. In this work, a gonioscopic lens is used to allow direct optical access of the TM through the cornea for MPM imaging. Compared to transscleral imaging, the acquired MPM images show improved resolution as individual collagen fiber bundles of the TM can be observed. MPM gonioscopy may have the potential to be developed as a future clinical imaging tool for glaucoma diagnostics.

  13. Osteoporosis and Impaired Trabecular Bone Score in Hemodialysis Patients

    Directory of Open Access Journals (Sweden)

    Ludmila Brunerová

    2016-06-01

    Full Text Available Background/Aims: Small attention is paid to other types of bone diseases then chronic kidney disease-mineral and bone disorder in dialysis patients. The aim of our study was to assess the occurrence of osteoporosis and bone microarchitecture by trabecular bone score in this population. Methods: 59 patients (67.6 ± 13.1 years, 43 males treated with hemodiafIltration underwent densitometry (Lunar Prodigy, TBS software 2.1.2 and laboratory assessment. Results: Osteoporosis was observed in 34% patients, high bone turnover was found in 80% of them, with SHPT (PTH > 300 ng/l present in 69%. TBS was significantly decreased in 47.5% of the patients. TBS correlated with T- and Z-scores of the lumbar spine and proximal femur in the total population (P Conclusions: Osteoporosis was found in about 1/3 of patients treated with hemodiafiltration. Normal TBS was found in only 1/4 of the dialysis population. TBS correlated with densitometric parameters and was significantly different relative to T-scores.

  14. Dry cupping for plantar fasciitis: a randomized controlled trial.

    Science.gov (United States)

    Ge, Weiqing; Leson, Chelsea; Vukovic, Corey

    2017-05-01

    [Purpose] The purpose of this study was to determine the effects of dry cupping on pain and function of patients with plantar fasciitis. [Subjects and Methods] Twenty-nine subjects (age 15 to 59 years old, 20 females and 9 males), randomly assigned into the two groups (dry cupping therapy and electrical stimulation therapy groups), participated in this study. The research design was a randomized controlled trial (RCT). Treatments were provided to the subjects twice a week for 4 weeks. Outcome measurements included the Visual Analogue Pain Scale (VAS) (at rest, first in the morning, and with activities), the Foot and Ankle Ability Measure (FAAM), the Lower Extremity Functional Scale (LEFS), as well as the pressure pain threshold. [Results]The data indicated that both dry cupping therapy and electrical stimulation therapy could reduce pain and increase function significantly in the population tested, as all the 95% Confidence Intervals (CIs) did not include 0 except for the pressure pain threshold. There was no significant difference between the dry cupping therapy and electrical stimulation groups in all the outcome measurements. [Conclusion] These results support that both dry cupping therapy and electrical stimulation therapy could reduce pain and increase function in the population tested.

  15. Cup regulates oskar mRNA stability during oogenesis.

    Science.gov (United States)

    Broyer, Risa M; Monfort, Elena; Wilhelm, James E

    2017-01-01

    The proper regulation of the localization, translation, and stability of maternally deposited transcripts is essential for embryonic development in many organisms. These different forms of regulation are mediated by the various protein subunits of the ribonucleoprotein (RNP) complexes that assemble on maternal mRNAs. However, while many of the subunits that regulate the localization and translation of maternal transcripts have been identified, relatively little is known about how maternal mRNAs are stockpiled and stored in a stable form to support early development. One of the best characterized regulators of maternal transcripts is Cup - a broadly conserved component of the maternal RNP complex that in Drosophila acts as a translational repressor of the localized message oskar. In this study, we have found that loss of cup disrupts the localization of both the oskar mRNA and its associated proteins to the posterior pole of the developing oocyte. This defect is not due to a failure to specify the oocyte or to disruption of RNP transport. Rather, the localization defects are due to a drop in oskar mRNA levels in cup mutant egg chambers. Thus, in addition to its role in regulating oskar mRNA translation, Cup also plays a critical role in controlling the stability of the oskar transcript. This suggests that Cup is ideally positioned to coordinate the translational control function of the maternal RNP complex with its role in storing maternal transcripts in a stable form. Published by Elsevier Inc.

  16. Classification of operational characteristics of commercial cup-anemometers

    Energy Technology Data Exchange (ETDEWEB)

    Friis Pedersen, T.; Schmidt Paulsen, U. [Risoe National Lab., Wind Energy and Atmospheric Physics Dept., Roskilde (Denmark)

    1999-03-01

    The present classification of cup-anemometers is based on a procedure for classification of operational characteristics of cup-anemometers that was proposed at the EWEC `97 conference in Dublin 1997. Three definitions of wind speed are considered. The average longitudinal wind speed (ID), the average horizontal wind speed (2D) and the average vector wind speed (3D). The classification is provided in these terms, and additionally, the turbulence intensities, which are defined from the same wind speed definitions. The commercial cup-anemometers have all been calibrated in wind tunnel for the normal calibrations and angular characteristics. Friction was measured by blywheel testing, where the surrounding temperatures were varied over a wide range. The characteristics of the cup-anemometers have been fitted to the heuristic dynamic model, and the response has been calculated in time domain for prescribed ranges of external operational conditions. The results are presented in ranges of maximum deviations of `measured` average wind speed. For each definition of wind speed and turbulence intensity, the cup-anemometers are ranked according to the most precise instrument. Finally, the most important systematic error sources are commented. (au)

  17. Medical report from the 2006 FIFA World Cup Germany

    Science.gov (United States)

    Dvorak, Jiri; Junge, Astrid; Grimm, Katharina; Kirkendall, Donald

    2007-01-01

    Objective To continue the injury surveillance of FIFA‐sponsored football tournaments and report on other medical aspects of the 2006 FIFA World Cup. Design Prospective epidemiological injury surveillance and descriptive summary of additional medical aspects. Setting Major international football tournament. Participants National team players, doctors and referees at the 2006 FIFA World Cup Germany. Main outcome measures Injury type, location and rate. Results 145 injuries were reported for the 64 matches of the 2006 FIFA World Cup Germany—an overall injury rate of 68.7 per 1000 match hours (95% CI 57.5 to 79.9) or 2.3 injuries per match, in comparison with 2.7 injuries per match in the 2002 FIFA World Cup (p = NS). Physical examinations before participation uncovered no hidden cardiovascular problems. Once the tournament started, no referees were unable to complete their duties. There were no positive doping tests. Conclusions The injury rate for this World Cup was below that of 2002, but consistent with the overall injury rate per match since data collection began in 1998. There continues to be no evidence of systematic doping in international football. PMID:17510228

  18. Octopus-like suction cups: from natural to artificial solutions.

    Science.gov (United States)

    Tramacere, F; Follador, M; Pugno, N M; Mazzolai, B

    2015-05-13

    Octopus suckers are able to attach to all nonporous surfaces and generate a very strong attachment force. The well-known attachment features of this animal result from the softness of the sucker tissues and the surface morphology of the portion of the sucker that is in contact with objects or substrates. Unlike artificial suction cups, octopus suckers are characterized by a series of radial grooves that increase the area subjected to pressure reduction during attachment. In this study, we constructed artificial suction cups with different surface geometries and tested their attachment performances using a pull-off setup. First, smooth suction cups were obtained for casting; then, sucker surfaces were engraved with a laser cutter. As expected, for all the tested cases, the engraving treatment enhanced the attachment performance of the elastomeric suction cups compared with that of the smooth versions. Moreover, the results indicated that the surface geometry with the best attachment performance was the geometry most similar to octopus sucker morphology. The results obtained in this work can be utilized to design artificial suction cups with higher wet attachment performance.

  19. Dielectric elastomer actuators for octopus inspired suction cups.

    Science.gov (United States)

    Follador, M; Tramacere, F; Mazzolai, B

    2014-09-25

    Suction cups are often found in nature as attachment strategy in water. Nevertheless, the application of the artificial counterpart is limited by the dimension of the actuators and their usability in wet conditions. A novel design for the development of a suction cup inspired by octopus suckers is presented. The main focus of this research was on the modelling and characterization of the actuation unit, and a first prototype of the suction cup was realized as a proof of concept. The actuation of the suction cup is based on dielectric elastomer actuators. The presented device works in a wet environment, has an integrated actuation system, and is soft. The dimensions of the artificial suction cups are comparable to proximal octopus suckers, and the attachment mechanism is similar to the biological counterpart. The design approach proposed for the actuator allows the definition of the parameters for its development and for obtaining a desired pressure in water. The fabricated actuator is able to produce up to 6 kPa of pressure in water, reaching the maximum pressure in less than 300 ms.

  20. Dielectric elastomer actuators for octopus inspired suction cups

    International Nuclear Information System (INIS)

    Follador, M; Tramacere, F; Mazzolai, B

    2014-01-01

    Suction cups are often found in nature as attachment strategy in water. Nevertheless, the application of the artificial counterpart is limited by the dimension of the actuators and their usability in wet conditions. A novel design for the development of a suction cup inspired by octopus suckers is presented. The main focus of this research was on the modelling and characterization of the actuation unit, and a first prototype of the suction cup was realized as a proof of concept. The actuation of the suction cup is based on dielectric elastomer actuators. The presented device works in a wet environment, has an integrated actuation system, and is soft. The dimensions of the artificial suction cups are comparable to proximal octopus suckers, and the attachment mechanism is similar to the biological counterpart. The design approach proposed for the actuator allows the definition of the parameters for its development and for obtaining a desired pressure in water. The fabricated actuator is able to produce up to 6 kPa of pressure in water, reaching the maximum pressure in less than 300 ms. (paper)

  1. Mathematical analysis of the effect of rotor geometry on cup anemometer response.

    Science.gov (United States)

    Sanz-Andrés, Ángel; Pindado, Santiago; Sorribes-Palmer, Félix

    2014-01-01

    The calibration coefficients of two commercial anemometers equipped with different rotors were studied. The rotor cups had the same conical shape, while the size and distance to the rotation axis varied. The analysis was based on the 2-cup positions analytical model, derived using perturbation methods to include second-order effects such as pressure distribution along the rotating cups and friction. The comparison with the experimental data indicates a nonuniform distribution of aerodynamic forces on the rotating cups, with higher forces closer to the rotating axis. The 2-cup analytical model is proven to be accurate enough to study the effect of complex forces on cup anemometer performance.

  2. Trabecular microstructure and surface changes in the greater tuberosity in rotator cuff tears

    International Nuclear Information System (INIS)

    Jiang, Yebin; Zhao, Jenny; Ouyang, Xiaolong; Genant, Harry K.; Holsbeeck, Marnix T. van; Flynn, Michael J.

    2002-01-01

    Abstract Objective. When planning surgery in patients with rotator cuff tear, strength of bone at the tendon insertion and trabecular bone structure in the greater tuberosity are usually taken into consideration. We investigated radiographic changes in bone structure of the greater tuberosity in rotator cuff tears.Design. Twenty-two human cadaveric shoulders from subjects ranging from 55 to 75 years of age were obtained. The integrity of the rotator cuff was examined by sonography to determine if it is intact without any tear, or torn partially or completely. The humeral head was sectioned in 3 mm thick coronal slab sections and microradiographed. After digitization of the microradiographs and imaging processing with in-house semi-automated image processing software tools developed using software interfaces on a Sun workstation, the trabecular histomorphometrical structural parameters and connectivity in the greater tuberosity were quantified. The degenerative changes on the surface of the greater tuberosity were interpreted blindly by 2 independent readers.Results. Among the 22 shoulder specimens, the rotator cuff was found intact in 10 shoulders, partially in 7 and fully torn in 5. Statistically significant loss in apparent trabecular bone volume fraction, number of trabecular nodes, and number of trabecular branches, and a statistically significant increase in apparent trabecular separation and number of trabecular free ends were found in the greater tuberosity of the shoulders with tears. The loss was greater in association with full tear than in partial tear. Thickening of the cortical margin of the enthesis, irregularity of its surface, and calcification beyond the tidemark were observed in 2 (20%) shoulders with intact rotator cuff, in 6 (86%) shoulders with partial tear, and in 5 (100%) shoulders with full tear.Conclusions. Rotator cuff tears are associated with degenerative changes on the bone surface and with disuse osteopenia of the greater tuberosity

  3. A novel cupping-assisted plasma treatment for skin disinfection

    Science.gov (United States)

    Xiong, Zilan; Graves, David B.

    2017-02-01

    A novel plasma treatment method/plasma source called cupping-assisted plasma treatment/source for skin disinfection is introduced. The idea combines ancient Chinese ‘cupping’ technology with plasma sources to generate active plasma inside an isolated, pressure-controlled chamber attached to the skin. Advantages of lower pressure include reducing the threshold voltage for plasma ignition and improving the spatial uniformity of the plasma treatment. In addition, with reduced pressure inside the cup, skin pore permeability might be increased and it improves attachment of the plasma device to the skin. Moreover, at a given pressure, plasma-generated active species are restricted inside the cup, raising local reactive species concentration and enhancing the measured surface disinfection rate. A surface micro-discharge (SMD) device is used as an example of a working plasma source. We report discharge characteristics and disinfection efficiency as a function of pressure and applied voltage.

  4. An aerodynamic analysis of recent FIFA world cup balls

    Science.gov (United States)

    Kiratidis, Adrian L.; Leinweber, Derek B.

    2018-05-01

    Drag and lift coefficients of recent FIFA world cup balls are examined. We fit a novel functional form to drag coefficient curves and in the absence of empirical data provide estimates of lift coefficient behaviour via a consideration of the physics of the boundary layer. Differences in both these coefficients for recent balls, which result from surface texture modification, can significantly alter trajectories. Numerical simulations are used to quantify the effect these changes have on the flight paths of various balls. Altitude and temperature variations at recent world cup events are also discussed. We conclude by quantifying the influence these variations have on the three most recent world cup balls, the Brazuca, the Jabulani and the Teamgeist. While our paper presents findings of interest to the professional sports scientist, it remains accessible to students at the undergraduate level.

  5. Effect of trabecular bone loss on cortical strain rate during impact in an in vitro model of avian femur

    Directory of Open Access Journals (Sweden)

    Gefen Amit

    2006-07-01

    Full Text Available Abstract Background Osteoporotic hip fractures occur due to loss of cortical and trabecular bone mass and consequent degradation in whole bone strength. The direct cause of most fractures is a fall, and hence, characterizing the mechanical behavior of a whole osteopenic bone under impact is important. However, very little is known about the mechanical interactions between cortical and trabecular bone during impact, and it is specifically unclear to what extent epiphyseal trabecular bone contributes to impact resistance of whole bones. We hypothesized that trabecular bone serves as a structural support to the cortex during impact, and hence, loss of a critical mass of trabecular bone reduces internal constraining of the cortex, and, thereby, decreases the impact tolerance of the whole bone. Methods To test this hypothesis, we conducted cortical strain rate measurements in adult chicken's proximal femora subjected to a Charpy impact test, after removing different trabecular bone core masses to simulate different osteopenic severities. Results We found that removal of core trabecular bone decreased by ~10-fold the cortical strain rate at the side opposite to impact (p Conclusion We conclude that in our in vitro avian model, loss of over 10% of core trabecular bone substantially altered the deformation response of whole bone to impact, which supports the above hypothesis and indicates that integrity of trabecular bone is critical for resisting impact loads.

  6. Earliest directly-dated human skull-cups.

    Directory of Open Access Journals (Sweden)

    Silvia M Bello

    Full Text Available BACKGROUND: The use of human braincases as drinking cups and containers has extensive historic and ethnographic documentation, but archaeological examples are extremely rare. In the Upper Palaeolithic of western Europe, cut-marked and broken human bones are widespread in the Magdalenian (∼15 to 12,000 years BP and skull-cup preparation is an element of this tradition. PRINCIPAL FINDINGS: Here we describe the post-mortem processing of human heads at the Upper Palaeolithic site of Gough's Cave (Somerset, England and identify a range of modifications associated with the production of skull-cups. New analyses of human remains from Gough's Cave demonstrate the skilled post-mortem manipulation of human bodies. Results of the research suggest the processing of cadavers for the consumption of body tissues (bone marrow, accompanied by meticulous shaping of cranial vaults. The distribution of cut-marks and percussion features indicates that the skulls were scrupulously 'cleaned' of any soft tissues, and subsequently modified by controlled removal of the facial region and breakage of the cranial base along a sub-horizontal plane. The vaults were also 'retouched', possibly to make the broken edges more regular. This manipulation suggests the shaping of skulls to produce skull-cups. CONCLUSIONS: Three skull-cups have been identified amongst the human bones from Gough's Cave. New ultrafiltered radiocarbon determinations provide direct dates of about 14,700 cal BP, making these the oldest directly dated skull-cups and the only examples known from the British Isles.

  7. An adaptation model for trabecular bone at different mechanical levels

    Directory of Open Access Journals (Sweden)

    Lv Linwei

    2010-07-01

    Full Text Available Abstract Background Bone has the ability to adapt to mechanical usage or other biophysical stimuli in terms of its mass and architecture, indicating that a certain mechanism exists for monitoring mechanical usage and controlling the bone's adaptation behaviors. There are four zones describing different bone adaptation behaviors: the disuse, adaptation, overload, and pathologic overload zones. In different zones, the changes of bone mass, as calculated by the difference between the amount of bone formed and what is resorbed, should be different. Methods An adaptation model for the trabecular bone at different mechanical levels was presented in this study based on a number of experimental observations and numerical algorithms in the literature. In the proposed model, the amount of bone formation and the probability of bone remodeling activation were proposed in accordance with the mechanical levels. Seven numerical simulation cases under different mechanical conditions were analyzed as examples by incorporating the adaptation model presented in this paper with the finite element method. Results The proposed bone adaptation model describes the well-known bone adaptation behaviors in different zones. The bone mass and architecture of the bone tissue within the adaptation zone almost remained unchanged. Although the probability of osteoclastic activation is enhanced in the overload zone, the potential of osteoblasts to form bones compensate for the osteoclastic resorption, eventually strengthening the bones. In the disuse zone, the disuse-mode remodeling removes bone tissue in disuse zone. Conclusions The study seeks to provide better understanding of the relationships between bone morphology and the mechanical, as well as biological environments. Furthermore, this paper provides a computational model and methodology for the numerical simulation of changes of bone structural morphology that are caused by changes of mechanical and biological

  8. Characterisation and classification of RISØ P2546 cup anemometer

    DEFF Research Database (Denmark)

    Friis Pedersen, Troels

    2004-01-01

    The characteristics of the RISØ P2546 cup anemometer were investigated in detail by wind tunnel and laboratory tests. The characteristics include accredited calibration, tilt response measurements for tilt angles between -40° to 40°, gust responsemeasurements at 8m/s and turbulence intensities...... of 10%, 16% and 23%, step response measurements at step wind speeds 3,7, 8, 11,9 and 15,2m/s, measurement of torque characteristics at 8m/s, rotor inertia measurements and measurements of friction ofbearings at temperatures -20°C to 40°C. Characteristics were fitted to a time domain cup anemometer model...

  9. Characterisation and classification of RISØ P2546 cup anemometer

    DEFF Research Database (Denmark)

    Friis Pedersen, Troels

    2003-01-01

    The characteristics of the RISØ P2546 cup anemometer were investigated in detail by wind tunnel and laboratory tests. The characteristics include accredited calibration, tilt response measurements for tilt angles between -40° to 40°, gust responsemeasurements at 8m/s and turbulence intensities...... of 10%, 16% and 23%, step response measurements at step wind speeds 3,7, 8, 11,9 and 15,2m/s, measurement of torque characteristics at 8m/s, rotor inertia measurements and measurements of friction ofbearings at temperatures -20°C to 40°C. Characteristics were fitted to a time domain cup anemometer model...

  10. Device for the prehension by means of suction cups

    International Nuclear Information System (INIS)

    Gabillet, Maurice

    1980-01-01

    The difficulties encountered while utilising suction-cups, are mainly caused by the skirts. The skirts are more or less adaptable to the surface of the objects to be handled. The skirt of the device presented, is made out of a round supple elastic bag containing solid particles. By creating a vacuum in the bag, the particles become a solid entity. The bag filled with the particles becomes rigid and can take exactly the shape of the object to be lifted. By creating a second vacuum in the axis of the bag, the object can be lifted. Several suction-cups can be used simultaneously

  11. Characterization of cellular solids in Ti6Al4V for orthopaedic implant applications: Trabecular titanium.

    Science.gov (United States)

    Marin, E; Fusi, S; Pressacco, M; Paussa, L; Fedrizzi, L

    2010-07-01

    EBM (Electron Beam Melting) technology can be used successfully to obtain cellular solids in metallic biomaterials that can greatly increase osseointegration in arthroprothesis and at the same time maintain good mechanical properties. The investigated structures, called Trabecular Titanium, usually cannot be obtained by traditional machining. Two samples: (A) with a smaller single cell area and, (B) with a bigger single cell area, were produced and studied in this project. They have been completely characterized and compared with the results in similar literature pertinent to Ti6Al4V EBM structures. Relative density was evaluated using different methods, the mean diameter of the open porosities was calculated by Scanning Electron Microscope images; the composition was evaluated using Energy-Dispersive X-Ray Spectroscopy; the microstructure (alpha-beta) was investigated using chemical etching and, the mechanical proprieties were investigated using UMTS. The mean porosity values resulted comparable with spongy bone (63% for A and 72% for B). The mean diameter of the single porosity (650 mum for A and 1400 mum for B) resulted compatible with the osseointegration data from the literature, in particular for sample A. The Vickers micro-hardness tests and the chemical etching demonstrated that the structure is fine, uniform and well distributed. The mechanical test proved that sample (A) was more resistant than sample (B), but sample (B) showed an elastic modulus almost equal to the value of spongy bone. The results of this study suggest that the two Ti6Al4V cellular solids can be used in biomedical applications to promote osseointegration demonstrating that they maybe successfully used in prosthetic implants. Additional implant results will be published in the near future. Copyright 2010 Elsevier Ltd. All rights reserved.

  12. Medieval trabecular bone architecture: the influence of age, sex, and lifestyle.

    Science.gov (United States)

    Agarwal, S C; Dumitriu, M; Tomlinson, G A; Grynpas, M D

    2004-05-01

    Osteoporosis has become a growing health concern in developed countries and an extensive area of research in skeletal biology. Despite numerous paleopathological studies of bone mass, few studies have measured bone quality in past populations. In order to examine age- and sex-related changes in one aspect of bone quality in the past, a study was made of trabecular bone architecture in a British medieval skeletal sample. X-ray images of 5-mm-thick coronal lumbar vertebral bone sections were taken from a total of 54 adult individuals divided into three age categories (18-29, 30-49, and 50+ years), and examined using image analysis to evaluate parameters related to trabecular bone structure and connectivity. Significant age-related changes in trabecular bone structure (trabecular bone volume (BV/TV), trabecular number (Tb.N), trabecular separation (Tb.Sp), and anisotropic ratio (Tb.An)) were observed to occur primarily by middle age with significant differences between the youngest and two older age groups. Neither sex showed continuing change in trabecular structure between the middle and old age groups. Age-related changes in bone connectivity (number of nodes (N.Nd) and node-to-node strut length (Nd.Nd)) similarly indicated a change in bone connectivity only between the youngest and two older age groups. However, females showed no statistical differences among the age groups in bone connectivity. These patterns of trabecular bone loss and fragility contrast with those generally found in modern populations that typically report continuing loss of bone structure and connectivity between middle and old age, and suggest greater loss in females. The patterns of bone loss in the archaeological samples must be interpreted cautiously. We speculate that while nutritional factors may have initiated some bone loss in both sexes, physical activity could have conserved bone architecture in old age in both sexes, and reproductive factors such as high parity and extended periods

  13. Acetabular cup position and risk of dislocation in primary total hip arthroplasty

    DEFF Research Database (Denmark)

    Seagrave, Kurt G; Troelsen, Anders; Malchau, Henrik

    2017-01-01

    Background and purpose - Hip dislocation is one of the most common complications following total hip arthroplasty (THA). Several factors that affect dislocation have been identified, including acetabular cup positioning. Optimal values for cup inclination and anteversion are debatable. We performed...

  14. A Confirmed Case of Toxic Shock Syndrome Associated with the Use of a Menstrual Cup

    Directory of Open Access Journals (Sweden)

    Michael A Mitchell

    2015-01-01

    Full Text Available Menstrual cups have been reported to be an acceptable substitute for tampons. These flexible cups have also been reported to provide a sustainable solution to menstrual management, with modest cost savings and no significant health risk.

  15. Trabecular bone structure analysis of the spine using clinical MDCT: can it predict vertebral bone strength?

    Science.gov (United States)

    Baum, Thomas; Gräbeldinger, Martin; Räth, Christoph; Garcia, Eduardo Grande; Burgkart, Rainer; Patsch, Janina M; Rummeny, Ernst J; Link, Thomas M; Bauer, Jan S

    2014-01-01

    Recent technical improvements have made it possible to determine trabecular bone structure parameters of the spine using clinical multi-detector computed tomography (MDCT). Therefore, the purpose of this study was to analyze trabecular bone structure parameters obtained from clinical MDCT in relation to high resolution peripheral quantitative computed tomography (HR-pQCT) as a standard of reference and to investigate whether clinical MDCT can predict vertebral bone strength. Fourteen functional spinal segment units between T7 and L3 were harvested from 14 formalin-fixed human cadavers (11 women and 3 men; age 84 ± 10 years). All functional spinal segment units were examined using HR-pQCT (isotropic voxel size of 41 μm(3)) and a clinical whole-body MDCT (interpolated voxel size of 146 × 146 × 300 μm(3)). Trabecular bone structure analyses (histomorphometric and texture measures) were performed in the HR-pQCT as well as MDCT images. Vertebral failure load (FL) of the functional spinal segment units was determined in an uniaxial biomechanical test. The HR-pQCT and MDCT derived trabecular bone structure parameters showed correlations ranging from r = 0.60 to r = 0.90 (p 0.05). In this cadaver model, the spatial resolution of clinically available whole-body MDCT scanners was suitable for trabecular bone structure analysis of the spine and to predict vertebral bone strength.

  16. The vertebral trabecular model revisited: magnetic field distribution in the vicinity of osseous disconnections

    Science.gov (United States)

    Kraiger, Markus; Schnizer, Bernhard; Stollberger, Rudolf

    2016-12-01

    In the current paper a vertebral bone model is introduced that can be used for studying trabecular thinning and the formation of trabecular disconnections. Magnetostatic simulations are applied in MR-osteodensitometry to deduce the quality of trabecular bone from experimentally obtained susceptibility effects. The course of trabecular bone loss, which results in distinct interruptions and consequently severe mechanical impairment, is not assessable in the majority of such applied models. In the novel approach introduced here, analytical solutions of prolate ellipsoids were used to compute the disturbed magnetic fields within the proposed 3D model. The performed simulations focused on two variants of the vertebral model: an intact model and a pathological model accounting for microdamage. For both variants, magnetic resonance spectra were simulated for different bone volume fractions. Subsequently, resonance signals were obtained from the Fourier transform of the distribution with respect to time. The resonance time courses were analyzed through common signal models to estimate the relaxation time {{T}\\prime}2 of the corresponding free induction decay. Detailed computations revealed the significant contribution of the microdamage to the susceptibility effect. Further, when comparing the line broadening effect between the intact and disrupted models a contradictory outcome was found. The damaged osseous network for the lower bone fraction resulted in faster decay of the transverse magnetization. In conclusion, a significant contribution of trabecular disconnections to the susceptibility effect has been shown by the presented model. Future dedicated MRI experiments can explore the use of this effect to assess the integrity of cancellous bone.

  17. Experimentally-based multiscale model of the elastic moduli of bovine trabecular bone and its constituents.

    Science.gov (United States)

    Hamed, Elham; Novitskaya, Ekaterina; Li, Jun; Jasiuk, Iwona; McKittrick, Joanna

    2015-09-01

    The elastic moduli of trabecular bone were modeled using an analytical multiscale approach. Trabecular bone was represented as a porous nanocomposite material with a hierarchical structure spanning from the collagen-mineral level to the trabecular architecture level. In parallel, compression testing was done on bovine femoral trabecular bone samples in two anatomical directions, parallel to the femoral neck axis and perpendicular to it, and the measured elastic moduli were compared with the corresponding theoretical results. To gain insights on the interaction of collagen and minerals at the nanoscale, bone samples were deproteinized or demineralized. After such processing, the treated samples remained as self-standing structures and were tested in compression. Micro-computed tomography was used to characterize the hierarchical structure of these three bone types and to quantify the amount of bone porosity. The obtained experimental data served as inputs to the multiscale model and guided us to represent bone as an interpenetrating composite material. Good agreement was found between the theory and experiments for the elastic moduli of the untreated, deproteinized, and demineralized trabecular bone. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. A Novel Method for Assessment of Polyethylene Liner Wear in Radiopaque Tantalum Acetabular Cups

    DEFF Research Database (Denmark)

    Troelsen, Anders; Greene, Meridith E; Ayers, David C

    2015-01-01

    Conventional radiostereometric analysis (RSA) for wear is not possible in patients with tantalum cups. We propose a novel method for wear analysis in tantalum cups. Wear was assessed by gold standard RSA and the novel method in total hip arthroplasty patients enrolled in a randomized controlled...... to the gold standard in titanium cups. The novel method offered accurate assessment and is a viable solution for assessment of wear in studies with tantalum cups....

  19. STANDARDIZATION OF CUPPING THERAPY POINTS AND MECHANISM OF ACTION IN THE LIGHT OF SCIENCE

    OpenAIRE

    Dr. Izharul Hasan

    2018-01-01

    Now a day’s cupping therapy is an established therapeutic modality among Indian system of medicine as well as worldwide. Inspite of that, standard operative procedure (SOPs) for cupping therapy is yet to develop. In this paper author comprises the possible indications of cupping therapy along with procedures, application points, safety concerns, historical perspective, surgical operative standards described in traditional system of medicine as well as in the light of science. Cupping may be d...

  20. Clinical research evidence of cupping therapy in China: a systematic literature review

    OpenAIRE

    Cao, Huijuan; Han, Mei; Li, Xun; Dong, Shangjuan; Shang, Yongmei; Wang, Qian; Xu, Shu; Liu, Jianping

    2010-01-01

    Abstract Background Though cupping therapy has been used in China for thousands of years, there has been no systematic summary of clinical research on it. This review is to evaluate the therapeutic effect of cupping therapy using evidence-based approach based on all available clinical studies. Methods We included all clinical studies on cupping therapy for all kinds of diseases. We searched six electronic databases, all searches ended in December 2008. We extracted data on the type of cupping...

  1. An overview of systematic reviews of clinical evidence for cupping therapy

    OpenAIRE

    Cao, Huijuan; Han, Mei; Zhu, Xiaoshu; Liu, Jianping

    2015-01-01

    Background: As a traditional treatment method, cupping therapy is widely used in Asian countries. This overview of systematic reviews (SRs) investigated the effectiveness and safety of cupping therapy through an evidence-based approach. Methods: SRs that assessed the effectiveness of cupping therapy for any type of disease were searched through 6 electronic databases. Target diseases, cupping methods, numbers and types of included studies, quality of included trials, main results (includin...

  2. Three-dimensional stress analysis of threaded cups - a finite element analysis.

    Science.gov (United States)

    Witzel, U; Rieger, W; Effenberger, H

    2008-04-01

    A three-dimensional model of the left acetabulum with inserted threaded cup has been generated, based on the finite element method, to calculate stress patterns in the standing phase during walking. In this study, a hemispherical cup with sharp threads, a parabolic cup with flat threads and a conical cup with sharp threads were analysed and compared. Stress patterns in both implant components and adjacent bony structures were calculated in a directly postoperative situation. The different cups were found to induce different stress patterns, deformations and shifting tendencies. The inlays deform notably and show characteristic rotational movement patterns together with the shell. The inclination angle increases in the hemispherical cup and decreases in the parabolic cup. The conical cup levers outward almost parallel to the bone stock by approximately 0.05 mm. The pole surfaces of the various cups - especially the very convex area next to the threads - induce increased compressive stress in the superior section of the acetabular base. This is increased by a factor of three in the conical cup in comparison to the hemispherical cup and less so in comparison to the parabolic cup. This study illustrates that three-dimensional stress calculations are suitable for procuring additional biomechanical information to augment clinical studies, for evaluating implants and for establishing stability prognoses, especially for newly developed prototypes.

  3. Three-dimensional stress analysis of threaded cups – a finite element analysis

    Science.gov (United States)

    Witzel, U.; Rieger, W.

    2007-01-01

    A three-dimensional model of the left acetabulum with inserted threaded cup has been generated, based on the finite element method, to calculate stress patterns in the standing phase during walking. In this study, a hemispherical cup with sharp threads, a parabolic cup with flat threads and a conical cup with sharp threads were analysed and compared. Stress patterns in both implant components and adjacent bony structures were calculated in a directly postoperative situation. The different cups were found to induce different stress patterns, deformations and shifting tendencies. The inlays deform notably and show characteristic rotational movement patterns together with the shell. The inclination angle increases in the hemispherical cup and decreases in the parabolic cup. The conical cup levers outward almost parallel to the bone stock by approximately 0.05 mm. The pole surfaces of the various cups – especially the very convex area next to the threads – induce increased compressive stress in the superior section of the acetabular base. This is increased by a factor of three in the conical cup in comparison to the hemispherical cup and less so in comparison to the parabolic cup. This study illustrates that three-dimensional stress calculations are suitable for procuring additional biomechanical information to augment clinical studies, for evaluating implants and for establishing stability prognoses, especially for newly developed prototypes. PMID:17318551

  4. Dry cupping in children with functional constipation: A randomized ...

    African Journals Online (AJOL)

    Background: As a common disease in pediatrics, constipation poses a high burden to the community. In this study, we aimed to investigate the efficacy of dry cupping therapy (an Eastern traditional manipulative therapy) in children with functional constipation. Materials and Methods: One hundred and twenty children (4-18 ...

  5. Sectoral labour market effects of the 2006 FIFA World Cup

    DEFF Research Database (Denmark)

    Feddersen, Arne; Maennig, Wolfgang

    2012-01-01

    Using the case of the 2006 FIFA World Cup, this study is the first to test the employment effects of a mega-sporting event on the basis of data that combines both regional and sectoral data. It is also the first study of sporting events to use a semi-parametric test method. Earlier studies...

  6. The age grading and the Chen-Ruan cup product

    DEFF Research Database (Denmark)

    A. Hepworth, Richard

    2010-01-01

    We prove that the obstruction bundle used to define the cup-product in Chen-Ruan cohomology is determined by the so-called `age grading' or `degree-shifting numbers'. Indeed, the obstruction bundle can be directly computed using the age grading. We obtain a Kunneth Theorem for Chen-Ruan cohomology...

  7. RoboCup Rescue Robot and Simulation Leagues

    NARCIS (Netherlands)

    Akin, H.L.; Ito, N.; Jacoff, A.; Kleiner, A.; Pellenz, J.; Visser, A.

    2013-01-01

    The RoboCup Rescue Robot and Simulation competitions have been held since 2000. The experience gained during these competitions has increased the maturity level of the field, which allowed deploying robots after real disasters (for example, Fukushima Daiichi nuclear disaster). This article provides

  8. Characterisation and classification of RISOe P2546 cup anemometer

    Energy Technology Data Exchange (ETDEWEB)

    Friis Pedersen, T.

    2004-03-01

    The characteristics of the RISOe P2546 cup anemometer were investigated in detail, and all data presented in figures and tables. The characteristics include: wind tunnel calibrations, including an accredited calibration; tilt response meas-urements for tilt angles from -40 deg. C to 40 deg. C; gust response measurements at 8m/s, 10,5m/s and 13m/s and turbulence intensities of 10%, 16% and 23%; step response measurements at step wind speeds 4, 8, 12 and 15m/s; measurement of torque characteristics at 8m/s; rotor inertia measurements and measurements of friction of bearings at temperatures -20 deg. C to 40 deg. C. The characteristics are fitted to a time domain cup anemometer model, and the cup anemometer is put into the CLASSCUP classification scheme. The characteristics are also compared to the requirements to cup anemometers in the Danish wind turbine certification system and the CD and CDV of the revision of the standard IEC 61400-12. (au)

  9. Injuries among World Cup ski and snowboard athletes.

    Science.gov (United States)

    Flørenes, T W; Nordsletten, L; Heir, S; Bahr, R

    2012-02-01

    There is little information available on injuries to World Cup skiers and snowboarders. The aim of this study was to describe and compare the injury risk to World Cup athletes in alpine skiing, freestyle skiing, snowboarding, ski jumping, Nordic combined and cross country skiing. We performed retrospective interviews with the International Ski Federation (FIS) World Cup athletes from selected nations during the 2006-2007 and 2007-2008 winter seasons and recorded all acute injuries occurring during the seasons. We interviewed 2121 athletes and recorded 705 injuries. There were 520 (72%) time-loss injuries and 196 (28%) severe injuries (absence >28 days). In freestyle skiing, alpine skiing and snowboarding, there were 27.6, 29.8 and 37.8 time-loss and 14.4, 11.3 and 13.8 severe injuries per 100 athletes per season, respectively. In Nordic combined, ski jumping and cross country skiing, there were 15.8, 13.6 and 6.3 time-loss and 3.3, 5.6 and 0.7 severe injuries per 100 athletes per season, respectively. In conclusion about 1/3 of the World Cup alpine, freestyle and snowboard athletes sustain a time-loss injury each season, while the risk is low in the Nordic disciplines. A particular concern was the high proportion of severe injuries observed among alpine, freestyle and snowboard athletes, which is in contrast to most other sports. © 2010 John Wiley & Sons A/S.

  10. Green goal: Awareness of the 2010 FIFA World Cup's greening ...

    African Journals Online (AJOL)

    South Africa hosted its first mega event (the FIFA World Cup) from 11th June to 11th July, 2010. Given the scope of the event and the opportunities it provided, the Department of Environmental Affairs and Tourism (DEAT) embarked on the 2010 National Volunteer Programme together with other greening initiatives/ ...

  11. NASCAR Winston Cup Race Results for 1975-2003

    Science.gov (United States)

    Winner, Larry

    2006-01-01

    Stock car racing has seen tremendous growth in popularity in recent years. We introduce two datasets containing results from all Winston Cup races between 1975 and 2003, inclusive. Students can use any number of statistical methods and applications of basic probability on the data to answer a wide range of practical questions. Instructors and…

  12. Microindentation hardness evaluation of iridium alloy clad vent set cups

    International Nuclear Information System (INIS)

    Ulrich, G.B.; DeRoos, L.F.; Stinnette, S.E.

    1993-01-01

    An iridium alloy, DOP-26, is used as cladding for 238 PuO 2 fuel in radioisotope heat sources for space power systems. Presently, DOP-26 iridium alloy clad vent sets (CVS) are being manufactured at the Oak Ridge Y-12 Plant for potential use in the National Aeronautics and Space Administration's Cassini mission to Saturn. Wrought/ground/stress relieved blanks are warm formed into CVS cups. These cups are then annealed to recrystallize the material for subsequent fabrication/assembly operations as well as for final use. One of the cup manufacturing certification requirements is to test for Vickers microindentation hardness. New microindentation hardness specification limits, 210 to 310 HV, have been established for a test load of 1000 grams-force (gf). The original specification limits, 250 to 350 HV, were for 200 gf testing. The primary reason for switching to a higher test load was to reduce variability in the test data. The DOP-26 alloy exhibits microindentation hardness load dependence, therefore, new limits were needed for 1000 gf testing. The new limits were established by testing material from 15 CVS cups using 200 gf and 1000 gf loads and then statistically analyzing the data. Additional work using a Knoop indenter and a 10 gf load indicated that the DOP-26 alloy grain boundaries have higher hardnesses than the grain interiors

  13. The 2010 FIFA World Cup and the Eden District Municipality ...

    African Journals Online (AJOL)

    Research on sport tourism, mega sport events and the impacts thereof, especially in developing countries, have, in the past, tended to have been overlooked. This article investigates 2010 FIFA World Cup initiatives conducted in the Eden District Municipality (EDM), Western Cape, South Africa, which is situated between the ...

  14. The Brazilian World Cup: too hot for soccer?

    Science.gov (United States)

    Lucena, Rebecca Luna; Steinke, Ercília Torres; Pacheco, Christina; Vieira, Lucas Lima; Betancour, Maribel Olaya; Steinke, Valdir Adilson

    2017-12-01

    The main objective of this research was to analyze the climate data for the host cities of the soccer World Cup held in Brazil in June and July 2014. A great deal of criticism was expressed about the Brazilian climate in the national and international press and media in the run-up to the competition, suggesting that the air temperature and relative air humidity would be the main adversaries of the soccer teams, especially those from Europe, during the competition. An analysis of the weather was done at the places and times of each of the 64 matches held. A human thermal comfort index was calculated (discomfort index (DI)) for each of the matches in order to discover the real climatic conditions in the host cities during the 2014 World Cup and their potential influence on the teams and human comfort in general. During the 2014 World Cup, only two matches were played at temperatures above 30 °C, representing a negligible percentage of the total number of matches. The air temperature for over half the matches (53%) was 20-25 °C. The results showed the air temperature and relative humidity data analyzed here both individually and in the form of an index indicate that the World Cup held in Brazil in 2014 did not put any of the players at risk due to extreme heat.

  15. Teaching Transport Phenomena around a Cup of Coffee

    Science.gov (United States)

    Condoret, Jean Stephane

    2007-01-01

    The very common situation of waiting for the cooling of a cup of coffee is addressed through a conventional engineering approach, where several important concepts of heat and mass transfer are used. A numerical and analytical solution of the differential equations of the problem are proposed, and assessed by comparing to simple experiments.…

  16. Media exposure and sponsor recall: Cricket World Cup 2003 | Van ...

    African Journals Online (AJOL)

    This paper reports on a study into the relationship between media exposure and sponsor recall relating to an international event, namely the Cricket World Cup 2003 (CWC 2003). The application of sponsorship as a communication construct and recall as a media vehicle effect is investigated. Recall has been widely ...

  17. Ryder Cup ning rahvusvaheline kogemus teenindusvaldkonnast / Liis Meeras

    Index Scriptorium Estoniae

    Meeras, Liis

    2006-01-01

    Iirimaal Dublini lähedal Kildare maakonna provintsis asuvas K-Clubis 22.-24. septembrini toimunud 36. Ryder Cup turniirist, mis on üks prestiizhikaim golfiüritus maailmas. Oma muljetest räägivad üritusel teenindanud turismitudengid TÜ Pärnu kolledzhist

  18. Fractal analysis of mandibular trabecular bone: optimal tile sizes for the tile counting method.

    Science.gov (United States)

    Huh, Kyung-Hoe; Baik, Jee-Seon; Yi, Won-Jin; Heo, Min-Suk; Lee, Sam-Sun; Choi, Soon-Chul; Lee, Sun-Bok; Lee, Seung-Pyo

    2011-06-01

    This study was performed to determine the optimal tile size for the fractal dimension of the mandibular trabecular bone using a tile counting method. Digital intraoral radiographic images were obtained at the mandibular angle, molar, premolar, and incisor regions of 29 human dry mandibles. After preprocessing, the parameters representing morphometric characteristics of the trabecular bone were calculated. The fractal dimensions of the processed images were analyzed in various tile sizes by the tile counting method. The optimal range of tile size was 0.132 mm to 0.396 mm for the fractal dimension using the tile counting method. The sizes were closely related to the morphometric parameters. The fractal dimension of mandibular trabecular bone, as calculated with the tile counting method, can be best characterized with a range of tile sizes from 0.132 to 0.396 mm.

  19. Experimental observation of ultrasound fast and slow waves through three-dimensional printed trabecular bone phantoms.

    Science.gov (United States)

    Mézière, F; Juskova, P; Woittequand, J; Muller, M; Bossy, E; Boistel, Renaud; Malaquin, L; Derode, A

    2016-02-01

    In this paper, ultrasound measurements of 1:1 scale three-dimensional (3D) printed trabecular bone phantoms are reported. The micro-structure of a trabecular horse bone sample was obtained via synchrotron x-ray microtomography, converted to a 3D binary data set, and successfully 3D-printed at scale 1:1. Ultrasound through-transmission experiments were also performed through a highly anisotropic version of this structure, obtained by elongating the digitized structure prior to 3D printing. As in real anisotropic trabecular bone, both the fast and slow waves were observed. This illustrates the potential of stereolithography and the relevance of such bone phantoms for the study of ultrasound propagation in bone.

  20. Variability of morphometric parameters of human trabecular tissue from coxo-arthritis and osteoporotic samples

    Directory of Open Access Journals (Sweden)

    Franco Marinozzi

    2012-01-01

    Full Text Available Morphometric and architectural bone parameters change in diseases such as osteoarthritis and osteoporosis. The mechanical strength of bone is primarily influenced by bone quantity and quality. Bone quality is defined by parameters such as trabecular thickness, trabecular separation, trabecular density and degree of anisotropy that describe the micro-architectural structure of bone. Recently, many studies have validated microtomography as a valuable investigative technique to assess bone morphometry, thanks to micro-CT non-destructive, non-invasive and reliability features, in comparison to traditional techniques such as histology. The aim of this study is the analysis by micro-computed tomography of six specimens, extracted from patients affected by osteoarthritis and osteoporosis, in order to observe the tridimensional structure and calculate several morphometric parameters.

  1. Numerical simulation of the remodelling process of trabecular architecture around dental implants.

    Science.gov (United States)

    Wang, Chao; Wang, Lizhen; Liu, Xiaoyu; Fan, Yubo

    2014-01-01

    Dental implants may alter the mechanical environment in the jawbone, thereby causing remodelling and adaptation of the surrounding trabecular bone tissues. To improve the efficacy of dental implant systems, it is necessary to consider the effect of bone remodelling on the performance of the prosthetic systems. In this study, finite element simulations were implemented to predict the evolution of microarchitecture around four implant systems using a previously developed model that combines both adaptive and microdamage-based mechano-sensory mechanisms in bone remodelling process. Changes in the trabecular architecture around dental implants were mainly focused. The simulation results indicate that the orientational and ladder-like architecture around the implants predicted herein is in good agreement with those observed in animal experiments and clinical observations. The proposed algorithms were shown to be effective in simulating the remodelling process of trabecular architecture around dental implant systems. In addition, the architectural features around four typical dental implant systems in alveolar bone were evaluated comparatively.

  2. Morphological experimental study of bone stress at the interface acetabular bone/prosthetic cup in the bipolar hip prosthesis.

    Science.gov (United States)

    Anuşca, D; Pleşea, I E; Iliescu, N; Tomescu, P; Poenaru, F; Dascălu, V; Pop, O T

    2006-01-01

    By calculating the tension and distortion of the elements composing the bipolar prosthesis under extreme conditions encountered in real life using a special post-processing program, we established the variation curves of the contact pressure at the hip bone-cup, armor-cup and cup-femoral head interface. By comparing the data obtained from all the examined cases, important conclusions were drawn regarding the influence of tension and pressure distribution on the structural integrity and biomechanics of the prosthesis, as well as the acetabular wear and tear, in order to assess its reliability. The experimentally determined tension and distortion status at the acetabular bone-metal armour interface, lead to the wear and tear phenomenon, which can be explained by three mechanisms and theories incompletely reflecting the overall process. The histopathologic study of the acetabular bone tissue using FEM (finite elements method) on surgically removed specimens will probably lead to the identification of a series of factors that could reduce the rate of the wear and tear process.

  3. The economic value of the 2010 Soccer World Cup

    Directory of Open Access Journals (Sweden)

    M. Saayman

    2008-12-01

    Full Text Available Purpose: The purpose of this article is to estimate the potential economic value of the 2010 Soccer World Cup for South Africa. Problem investigated: The Soccer World Cup (SWC is regarded as the largest sporting event to be hosted and South Africa is investing billions of Rand in the hosting thereof. Based on this the question that comes to mind is, what is the potential economic value of such an event? Previous research attempts to determine the economic value were limited in their focus on what should be included when economic modelling of events is conducted. Most of these studies were done by consultants on behalf of various government departments and consequently, the results of these attempts are criticised for their over-inflating and overestimations by various other researchers. Methodology: The literature review identified many aspects that need to be taken into account when modelling the economic impact of such an event together with aspects identified in the literature review. Lessons from the 2002 Korea/Japan and 2006 Germany Soccer World Cups were used as premise for our estimations. In this article, Computable General Equilibrium (CGE modelling is used to estimate the potential economic value. Findings: The results showed that the 2010 Soccer World Cup would in all probability have positive impacts on the economy of the country in terms of GDP growth and employment, with possible negative effects that include higher inflation and net export losses. Value of research: The value of this research lies in the approach that was followed firstly, by introducing lessons learned from previous World Cups as well as aspects not taken into consideration previously in economic modelling and secondly, by using CGE modelling in determining the economic value. Conclusion: The hosting of the 2010 Soccer World Cup is a major achievement not only for South Africa, but also for the rest of Africa, especially from a marketing point of view. From an

  4. Failure of dual radius hydroxyapatite-coated acetabular cups

    Directory of Open Access Journals (Sweden)

    Zatti Giovanni

    2008-08-01

    Full Text Available Abstract Introduction Many kind of hydroxyapatite-coated cups were used, with favorable results in short term studies; it was supposed that its use could improve osteointegration of the cup, enhancing thus stability and survivorship. The purpose of this study is to analyze the long term behavior of the hemispheric HA coated, Dual Radius Osteonics cup and to discuss the way of failure through the exam of the revised components and of both periacetabular and osteolysis tissue. Materials and Methods Between 1994 and 1997, at the Department of Orthopedic Sciences of the Insubria University, using the posterolateral approach, were implanted 276 Dual Radius Osteonics® in 256 patients, with mean age of 63 years. Results At a mean follow-up of 10 years (range 8–12 years, 183 cups in 165 patients, were available for clinical and radiographical evaluation. 22 Cups among the 183 were revised (11%. The cause of revision was aseptic loosening in 17 cases, septic loosening in one case, periprosthetic fracture in another case, osteolysis and polyethylene wear in two cases and, finally, recurrent dislocations in the last one. In the remaining patients, mean HHS increased from a preoperative value of 50,15 to a postoperative value of 92,69. The mean polyethylene wear was 1,25 mm (min. 0,08, max. 3,9 mm, with a mean annual wear of 0,17 mm. The mean acetabular migration on the two axis was 1,6 mm and 1,8 mm. Peri-acetabular osteolysis were recorded in 89% of the implants (163 cases. The cumulative survivorship (revision as endpoint at the time was 88,9%. Conclusion Our study confirms the bad behavior of this type of cup probably related to the design, to the method of HA fixation. The observations carried out on the revised cup confirm these hypotheses but did not clarify if the third body wear could be a further problem. Another interesting aspect is the high incidence of osteolysis, which are often asymptomatic becoming a problem for the surgeon as the

  5. Running exercise alleviates trabecular bone loss and osteopenia in hemizygous β-globin knockout thalassemic mice.

    Science.gov (United States)

    Thongchote, Kanogwun; Svasti, Saovaros; Teerapornpuntakit, Jarinthorn; Krishnamra, Nateetip; Charoenphandhu, Narattaphol

    2014-06-15

    A marked decrease in β-globin production led to β-thalassemia, a hereditary anemic disease associated with bone marrow expansion, bone erosion, and osteoporosis. Herein, we aimed to investigate changes in bone mineral density (BMD) and trabecular microstructure in hemizygous β-globin knockout thalassemic (BKO) mice and to determine whether endurance running (60 min/day, 5 days/wk for 12 wk in running wheels) could effectively alleviate bone loss in BKO mice. Both male and female BKO mice (1-2 mo old) showed growth retardation as indicated by smaller body weight and femoral length than their wild-type littermates. A decrease in BMD was more severe in female than in male BKO mice. Bone histomorphometry revealed that BKO mice had decreases in trabecular bone volume, trabecular number, and trabecular thickness, presumably due to suppression of osteoblast-mediated bone formation and activation of osteoclast-mediated bone resorption, the latter of which was consistent with elevated serum levels of osteoclastogenic cytokines IL-1α and -1β. As determined by peripheral quantitative computed tomography, running increased cortical density and thickness in the femoral and tibial diaphyses of BKO mice compared with those of sedentary BKO mice. Several histomorphometric parameters suggested an enhancement of bone formation (e.g., increased mineral apposition rate) and suppression of bone resorption (e.g., decreased osteoclast surface), which led to increases in trabecular bone volume and trabecular thickness in running BKO mice. In conclusion, BKO mice exhibited pervasive osteopenia and impaired bone microstructure, whereas running exercise appeared to be an effective intervention in alleviating bone microstructural defect in β-thalassemia. Copyright © 2014 the American Physiological Society.

  6. Effect of torsional loading on compressive fatigue behaviour of trabecular bone.

    Science.gov (United States)

    Fatihhi, S J; Rabiatul, A A R; Harun, M N; Kadir, Mohammed Rafiq Abdul; Kamarul, T; Syahrom, Ardiyansyah

    2016-02-01

    The present study reports the effects of combined torsional and compressive cyclic loading on trabecular bone in order to mimic true physiological conditions and thereby provides improved data that represents clinical and real life conditions. However, only compressive behaviour is evaluated in most previous studies of bone mechanics. From the monotonic evaluation, it is observed that lower stress is needed for the onset of microcrack in the sample under torsional loading, compared to the stress needed in compression. Trabecular bone samples were subjected to a combination of torsion and compression fatigue at different stress levels during which they were compared to compressive axial fatigue. The stress levels were determined by considering the monotonic strength at 25-50% for both compressive and shear stresses. Significant decrease in fatigue lifetime is observed in between samples of pure compression fatigue and those with superpositioned torsional loading (ptorsional stress level. In this case, the failure of the sample is said to be 'torsional dominant'. Fatigue behaviour of bovine trabecular bone begins with plastic deformation, followed by strain accumulation and modulus reduction. As the strain rate increases, more energy dissipates and the sample finally failed. Further, the analysis of fractograph revealed something on the trabeculae by bending in sample with superpositioned torsional loading. In conclusion, torsional loading decreases the quality of the trabecular properties in terms of stiffness, life and structural integrity. It is hoped that results from this study will improve the understanding of the behaviour of trabecular bone under combined fatigue and help to develop future assessments of trabecular failure. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Timing of growth hormone treatment affects trabecular bone microarchitecture and mineralization in growth hormone deficient mice.

    Science.gov (United States)

    Kristensen, Erika; Hallgrímsson, Benedikt; Morck, Douglas W; Boyd, Steven K

    2010-08-01

    Growth hormone (GH) is essential in the development of bone mass, and a growth hormone deficiency (GHD) in childhood is frequently treated with daily injections of GH. It is not clear what effect GHD and its treatment has on bone. It was hypothesized that GHD would result in impaired microarchitecture, and an early onset of treatment would result in a better recovery than late onset. Growth hormone deficient homozygous (lit/lit) mice of both sexes were divided into two treatment groups receiving daily injections of GH, starting at an early (21 days of age) or a late time point (35 days of age, corresponding to the end of puberty). A group of heterozygous mice with normal levels of growth hormone served as controls. In vivo micro-computed tomography scans of the fourth lumbar vertebra were obtained at five time points between 21 and 60 days of age, and trabecular morphology and volumetric BMD were analyzed to determine the effects of GH on bone microarchitecture. Early GH treatment led to significant improvements in bone volume ratio (p=0.006), tissue mineral density (p=0.005), and structure model index (p=0.004) by the study endpoint (day 60), with no detected change in trabecular thickness. Trabecular number increased and trabecular separation decreased in GHD mice regardless of treatment compared to heterozygous mice. This suggests fundamental differences in the structure of trabecular bone in GHD and GH treated mice, reflected by an increased number of thinner trabeculae in these mice compared to heterozygous controls. There were no significant differences between the late treatment group and GHD mice except for connectivity density. Taken together, these results indicate that bone responds to GH treatment initiated before puberty but not to treatment commencing post-puberty, and that GH treatment does not rescue the structure of trabecular bone to that of heterozygous controls. Copyright 2010 Elsevier Inc. All rights reserved.

  8. Radiological diagnostics in CUP syndrome; Radiologische Diagnostik des CUP-Syndroms

    Energy Technology Data Exchange (ETDEWEB)

    Kazmierczak, P.M.; Nikolaou, K.; Graser, A.; Reiser, M.F.; Cyran, C.C. [Klinikum der Ludwig-Maximilians-Universitaet, Campus Grosshadern, Institut fuer Klinische Radiologie, Muenchen (Germany); Rominger, A. [Klinikum der Ludwig-Maximilians-Universitaet, Campus Grosshadern, Klinik und Poliklinik fuer Nuklearmedizin, Muenchen (Germany)

    2014-02-15

    Imaging plays an essential role in the therapeutic management of cancer of unknown primary (CUP) patients for localizing the primary tumor, for the identification of tumor entities for which a dedicated therapy regimen is available and for the characterization of clinicopathological subentities that direct the subsequent diagnostic and therapeutic strategy. Modalities include conventional x-ray, computed tomography (CT), magnetic resonance imaging (MRI) and ultrasound as well as positron emission tomography (PET)-CT and MRI-PET. In whole body imaging CT has a high sensitivity for tumor entities which frequently present as a metastasized cancer illness. According to the current literature CT is diagnostic in 86% of patients with pancreatic carcinoma, in 36% of patients with colon carcinoma and in 74% of patients with lung carcinoma. Additionally a meta-analysis showed that for patients with squamous cell carcinoma and cervical lymph node metastases a positive diagnosis was possible in 22% of the cases using CT, in 36% using MRI and in 28-57% using 18F-fluorodeoxyglucose PET-CT ({sup 18}F-FDG PET-CT). In addition, MRI plays an important role in the localization of primary occult tumors (e.g. breast and prostate) because of its high soft tissue contrast and options for functional imaging. At the beginning of the diagnostic algorithm stands the search for a possible primary tumor and CT of the neck, thorax and abdomen is most frequently used for whole body staging. Subsequent organ-specific imaging examinations follow, e.g. mammography in women with axillary lymphadenopathy. For histological and immunohistochemical characterization of tumor tissue, imaging is also applied to identify the most accessible and representative tumor manifestation for biopsy. Tumor biopsy may be guided by CT, MRI or ultrasound and MRI also plays a central role in the localization of primary occult tumors because of superior soft tissue contrast and options for functional imaging (perfusion

  9. New series of cup combination vending machines; Cup combination jido hanbaiki no shin series

    Energy Technology Data Exchange (ETDEWEB)

    Mizutani, K.; Hamamoto, K. [Fuji Electric Co. Ltd., Tokyo (Japan); Yokoyama, K. [Fuji Electric Corporate Research and Development, Ltd., Kanagawa (Japan)

    1996-07-10

    This paper introduces the cup combination vending machines developed as new series. The point of development is to improve the taste of regular coffee, stabilize the taste of a beverage, design a bright door, improve the sanitary condition, and simplify the operativity. To improve the taste of coffee, coffee beans are ground using a mill in the vending machine and extracted at 95{degree}C by the brewer mechanism based on a forced drip system. A heater is provided in the pipe arrangement so as to keep the temperature of hot water that is an important factor for determining the taste. The taste of a powder beverage is stabilized by a uniform reduction function for first-in first-out that holds the freshness of materials and a high-precision discharge function that reduces the dispersion in discharge. Materials can be uniformly reduced by rotating the pin disk in the mixing part at the top of a canister. The taste of a syrup beverage is stabilized by a new-type carbonator that dissolves CO2 in cold water at a high dissolution rate and high retention rate and an ice quantitative unit that reduces the dispersion in ice discharge. 9 figs., 2 tabs.

  10. A geometric morphometric assessment of the optic cup in glaucoma.

    Science.gov (United States)

    Sanfilippo, Paul G; Cardini, Andrea; Sigal, Ian A; Ruddle, Jonathan B; Chua, Brian E; Hewitt, Alex W; Mackey, David A

    2010-09-01

    The morphologic appearance of the optic disc is of interest in glaucoma. In contrast to descriptive classification systems that are currently used, a quantitative approach to the analysis of optic disc morphology is required. Our goal was to determine the optimal method for quantifying optic cup shape by comparing traditional (ovality, form-factor and neuroretinal rim (NRR) width ratio) and geometric morphometric approaches. Left optic disc stereophotographs of 160 (80 normal and 80 glaucomatous (stratified by severity)) subjects were examined. The optic cup margins were stereoscopically delineated with a custom tracing system and saved as a series of discrete points. The geometric morphometric methods of elliptic Fourier analysis (EFA) and sliding semi-landmark analysis (SSLA) were used to eliminate variation unrelated to shape (e.g. size) and yield a series of shape variables. Differences in optic cup shape between normal and glaucoma groups were investigated. Discriminant functions were computed and the sensitivity and specificity of each technique determined. Receiver operator characteristic (ROC) curves were calculated for all methods and evaluated in their potential to discriminate between normal and glaucomatous eyes based on the shape variables. All geometric morphometric methods revealed differences between normal and glaucomatous eyes in optic cup shape, in addition to the traditional parameters of ovality, form-factor and NRR width ratio (pcurve (AUC) (0.91). EFA (72 points) performed similarly well (74%, 0.89) as did the set of traditional shape-based variables (76%, 0.86). This study demonstrated that a geometric morphometric approach for discriminating between normal and glaucomatous eyes in optic cup shape is superior to that provided by traditional single parameter shape measures. Such analytical techniques could be incorporated into future automated optic disc screening modalities. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

  11. Histogram-driven cupping correction (HDCC) in CT

    Science.gov (United States)

    Kyriakou, Y.; Meyer, M.; Lapp, R.; Kalender, W. A.

    2010-04-01

    Typical cupping correction methods are pre-processing methods which require either pre-calibration measurements or simulations of standard objects to approximate and correct for beam hardening and scatter. Some of them require the knowledge of spectra, detector characteristics, etc. The aim of this work was to develop a practical histogram-driven cupping correction (HDCC) method to post-process the reconstructed images. We use a polynomial representation of the raw-data generated by forward projection of the reconstructed images; forward and backprojection are performed on graphics processing units (GPU). The coefficients of the polynomial are optimized using a simplex minimization of the joint entropy of the CT image and its gradient. The algorithm was evaluated using simulations and measurements of homogeneous and inhomogeneous phantoms. For the measurements a C-arm flat-detector CT (FD-CT) system with a 30×40 cm2 detector, a kilovoltage on board imager (radiation therapy simulator) and a micro-CT system were used. The algorithm reduced cupping artifacts both in simulations and measurements using a fourth-order polynomial and was in good agreement to the reference. The minimization algorithm required less than 70 iterations to adjust the coefficients only performing a linear combination of basis images, thus executing without time consuming operations. HDCC reduced cupping artifacts without the necessity of pre-calibration or other scan information enabling a retrospective improvement of CT image homogeneity. However, the method can work with other cupping correction algorithms or in a calibration manner, as well.

  12. Importance of nuclear medicine diagnostics in CUP syndrome

    International Nuclear Information System (INIS)

    Winter, M.C.; Haberkorn, U.; Kratochwil, C.

    2014-01-01

    The diagnostic work-up in patients with carcinoma of unknown primary (CUP) syndrome is extensive, highly time-consuming and cost-intensive and ultimately often fails to detect a primary site. In this context chest X-ray and computed tomography (CT) have been used as standard imaging modalities in CUP syndrome. Since the introduction of positron emission tomography (PET) evaluation of tumor vitality has become possible. Furthermore, PET-CT hybrid scanners allow the combination of functional and morphological imaging. Several meta-analyses have reported an additional overall detection rate between 24.5 % and 44 % by either PET or PET-CT. Metastatic localization (cervical versus extracervical) did not influence the performance. The sensitivity was usually high (> 80 %) but specificity was moderate ranging from 68 % to 88 % at best. If mentioned, the results obtained by fluorodeoxyglucose (FDG)-PET significantly changed the clinical management in approximately one third of the patients studied. In a direct comparison with PET alone, PET-CT did not depict significantly more primary tumors but was able to reduce false positive findings. To determine the real additional value of PET-CT in the diagnosis of CUP syndrome large prospective studies with more uniform inclusion criteria are needed. Despite the capabilities of FDG-PET-CT there is as yet no evidence that a potentially improved diagnostic algorithm is translated into a better patient outcome. Nevertheless, FDG-PET-CT should be performed in all CUP patients where conventional imaging failed to detect a primary site or the results are equivocal. In CUP patients with cervical lymph node metastases PET-CT should be carried out prior to panendoscopy to reduce the number of false negative biopsies. (orig.) [de

  13. Football injuries during the 2014 FIFA World Cup

    Science.gov (United States)

    Junge, Astrid; Dvořák, Jiri

    2015-01-01

    Background FIFA has surveyed match injuries in its tournaments since 1998. Aim To analyse the incidence and characteristics of match injuries incurred during the 2014 FIFA World Cup in comparison to previous FIFA World Cups. Methods The chief physicians of the participating teams reported all newly incurred injuries of their players after the match on a standardised report form. 124 (97%) forms were returned. Results A total of 104 injuries were reported, equivalent to an incidence of 1.68 injuries per match (95% CI 1.36 to 2.00). 64 (63.4%) injuries were caused by contact with another player. Thigh (26; 25%) and head (19; 18%) were the most frequently injured body parts. The most frequent diagnosis was thigh strain (n=18). Five concussions and three fractures to the head were reported. While most thigh strains (15/17; 88.2%) occurred without contact, almost all head injuries (18/19; 94.7%) were caused by contact. 0.97 injuries per match (95% CI 0.72 to 1.22) were expected to result in absence from training or match. Eight injuries were classified as severe. The incidence of match injuries in the 2014 FIFA World Cup was significantly lower than the average of the four preceding FIFA World Cups, both for all injuries (2.34; 95% CI 2.15 to 2.53) and time-loss injuries (1.51; 95% CI 1.37 to 1.65). Conclusions The overall incidence of injury during the FIFA World Cups decreased from 2002 to 2014 by 37%. A detailed analysis of the injury mechanism is recommended to further improve prevention strategies. PMID:25878077

  14. Injuries among male and female World Cup alpine skiers.

    Science.gov (United States)

    Flørenes, T W; Bere, T; Nordsletten, L; Heir, S; Bahr, R

    2009-12-01

    Limited knowledge exists on injuries among professional alpine skiers. To describe the risk of injury and the injury pattern among competitive World Cup alpine skiers during the competitive season. Retrospective interviews were performed with all World Cup athletes from 10 nations at the end of the 2006-7 and 2007-8 winter seasons, and all acute injuries occurring during the 4.5-month competitive season were recorded. If the athlete was not present, their coaches or medical personnel were interviewed. A total of 191 acute injuries were recorded among 521 World Cup alpine skiers. As many as 86 injuries (45%) occurred during World Cup/World Ski Championship competitions, corresponding to an injury rate of 9.8 injuries per 1000 runs (95% CI 7.8 to 11.9). The injury rate was found to increase with increasing speed (slalom 4.9 injuries per 1000 runs, 95% CI 2.5 to 7.4--giant slalom 9.2, 5.1 to 13.3--super-G 11.0, 5.2 to 16.8--downhill 17.2, 11.6 to 22.7). The most frequently injured body part was the knee, with 68 injuries (36%), and 37 of these were severe. The overall injury rate was higher in males than in females, but not for knee injuries. The risk of injury among World Cup athletes in alpine skiing is even higher than previously reported. The knee is the most commonly injured body part and with many severe injuries. Injury rate increased with a higher speed and was higher among males than in females.

  15. Distributional variations in trabecular architecture of the mandibular bone: an in vivo micro-CT analysis in rats.

    Directory of Open Access Journals (Sweden)

    Zhongshuang Liu

    Full Text Available To evaluate the effect of trabecular thickness and trabecular separation on modulating the trabecular architecture of the mandibular bone in ovariectomized rats.Fourteen 12-week-old adult female Wistar rats were divided into an ovariectomy group (OVX and a sham-ovariectomy group (sham. Five months after the surgery, the mandibles from 14 rats (seven OVX and seven sham were analyzed by micro-CT. Images of inter-radicular alveolar bone of the mandibular first molars underwent three-dimensional reconstruction and were analyzed.Compared to the sham group, trabecular thickness in OVX alveolar bone decreased by 27% (P = 0.012, but trabecular separation in OVX alveolar bone increased by 59% (P = 0.005. A thickness and separation map showed that trabeculae of less than 100 μm increased by 46%, whereas trabeculae of more than 200 μm decreased by more than 40% in the OVX group compared to those in the sham group. Furthermore, the OVX separation of those trabecular of more than 200 μm was 65% higher compared to the sham group. Bone mineral density (P = 0.028 and bone volume fraction (p = 0.001 were also significantly decreased in the OVX group compared to the sham group.Ovariectomy-induced bone loss in mandibular bone may be related to the distributional variations in trabecular thickness and separation which profoundly impact the modulation of the trabecular architecture.

  16. Osteoporosis changes the amount of vertebral trabecular bone at risk of fracture but not the vertebral load distribution.

    NARCIS (Netherlands)

    Homminga, J.J.; Weinans, H.; Gowin, W.; Felsenberg, D.; Huiskes, R.

    2001-01-01

    STUDY DESIGN: A finite-element study to investigate the amount of trabecular bone at risk of fracture and the distribution of load between trabecular core and cortical shell, for healthy, osteopenic, and osteoporotic vertebrae. OBJECTIVES: To determine differences between healthy, osteopenic, and

  17. Muscle volume is related to trabecular and cortical bone architecture in typically developing children.

    Science.gov (United States)

    Bajaj, Deepti; Allerton, Brianne M; Kirby, Joshua T; Miller, Freeman; Rowe, David A; Pohlig, Ryan T; Modlesky, Christopher M

    2015-12-01

    Muscle is strongly related to cortical bone architecture in children; however, the relationship between muscle volume and trabecular bone architecture is poorly studied. The aim of this study was to determine if muscle volume is related to trabecular bone architecture in children and if the relationship is different than the relationship between muscle volume and cortical bone architecture. Forty typically developing children (20 boys and 20 girls; 6 to 12y) were included in the study. Measures of trabecular bone architecture [i.e., apparent trabecular bone volume to total volume (appBV/TV), trabecular number (appTb.N), trabecular thickness (appTb.Th) and trabecular separation (appTb.Sp)] in the distal femur, cortical bone architecture [cortical volume, total volume, section modulus (Z) and polar moment of inertia (J)] in the midfemur, muscle volume in the midthigh and femur length were assessed using magnetic resonance imaging. Total physical activity and moderate-to-vigorous physical activity were assessed using an accelerometer-based activity monitor worn around the waist for four days. Calcium intake was assessed using diet records. Relationships among the measures were tested using multiple linear regression analysis. Muscle volume was moderately-to-strongly related to measures of trabecular bone architecture [appBV/TV (r=0.81), appTb.N (r=0.53), appTb.Th (r=0.67), appTb.Sp (r=-0.71); all parchitecture [cortical volume (r=0.96), total volume (r=0.94), Z (r=0.94) and J (r=0.92; all parchitecture. Sex, physical activity and calcium intake were not related to any measure of bone architecture (p>0.05). Because muscle volume and femur length were strongly related (r=0.91, parchitecture (partial r=0.47 to 0.54; parchitecture in the distal femur of typically developing children. The relationship is weaker than the relationship between muscle volume in the midthigh and cortical bone architecture in the midfemur, but the discrepancy is driven, in large part, by the

  18. Genomic and post-genomic effects of anti-glaucoma drugs preservatives in trabecular meshwork

    Energy Technology Data Exchange (ETDEWEB)

    Izzotti, Alberto, E-mail: izzotti@unige.it [Mutagenesis Unit, IRCCS AOU San Martino – IST, Genova (Italy); Department of Health Sciences, University of Genoa, Via A. Pastore 1, 16132 Genoa (Italy); La Maestra, Sebastiano; Micale, Rosanna Tindara; Longobardi, Maria Grazia [Department of Health Sciences, University of Genoa, Via A. Pastore 1, 16132 Genoa (Italy); Saccà, Sergio Claudio [Ophthalmology Unit, IRCCS AOU San Martino-IST, Genova (Italy)

    2015-02-15

    Highlights: • Glaucoma drug preservatives induce DNA damage in trabecular meshwork cells. • Cellular alteration is related with the occurrence of activation of apoptosis through the intrinsic pathway. • Drug preservatives unable to induce cell damage are ineffective in killing bacteria. • Anti glaucoma drugs should be formulated as single-dose usage devoid of genotoxic preservatives. - Abstract: Oxidative stress plays an important role in glaucoma. Some preservatives of anti-glaucoma drugs, commonly used in glaucoma therapy, can prevent or induce oxidative stress in the trabecular meshwork. The aim of this study is to evaluate cellular and molecular damage induced in trabecular meshwork by preservatives contained in anti-glaucoma drugs. Cell viability (MTT test), DNA fragmentation (Comet test), oxidative DNA damage (8-oxo-dG), and gene expression (cDNA microarray) have been evaluated in trabecular meshwork specimens and in human trabecular meshwork cells treated with benzalkonium chloride, polyQuad, purite, and sofzia-like mixture. Moreover, antimicrobial effectiveness and safety of preservative contents in drugs was tested. In ex vivo experiments, benzalkonium chloride and polyQuad induced high level of DNA damage in trabecular meshwork specimens, while the effect of purite and sofzia were more attenuated. The level of DNA fragmentation induced by benzalkonium chloride was 2.4-fold higher in subjects older than 50 years than in younger subjects. Benzalkonium chloride, and polyQuad significantly increased oxidative DNA damage as compared to sham-treated specimens. Gene expression was altered by benzalkonium chloride, polyQuad, and purite but not by sofzia. In in vitro experiments, benzalkonium chloride and polyQuad dramatically decreased trabecular meshwork cell viability, increased DNA fragmentation, and altered gene expression. A lesser effect was also exerted by purite and sofzia. Genes targeted by these alterations included Fas and effector caspase-3

  19. Single- and dual energy QCT around acetabular cups in total hip arthroplasty using 3-dimensional segmentation

    DEFF Research Database (Denmark)

    Mussmann, Bo Redder; Andersen, Poul Erik; Torfing, Trine

    Introduction: Bone density measurements around hip implants are challenged by artifacts and the complex anatomy of the acetabulum. We developed 3D segmentation software and used dual energy CT to reduce artifacts. The between-scan agreement and reliability of the software was tested and bone...... of 14 mg/ccm, p=0.25 and 186 mg/ccm in DECT with a difference of 6 mg/ccm, p=0.15. ICC was >0.95 with more narrow limits of agreement in DECT compared with SECT. CTDI was 25% higher with DECT and subjective image quality was better in SECT. Conclusion: Equally reliable BMD measurements adjacent...... to acetabular cemented and uncemented cups can be performed using the segmentation software. The absolute between-scan agreement was better in DECT. Virtual monochromatic DECT with fast kVp switching may be beneficial in estimating BMD adjacent to metal implants, but radiation dose and image quality should...

  20. [Development of lipoma following a single cupping massage - a case report].

    Science.gov (United States)

    Schumann, Stefan; Lauche, Romy; Hohmann, Claudia; Zirbes, Thomas; Dobos, Gustav; Saha, Felix Joyonto

    2012-01-01

    The cupping massage is a form of bloodless cupping. This type of cupping is particularly used to treat muscular tension and musculoskeletal pain, such as chronic neck pain; however the data records on mechanisms and potential side effects are not satisfactory. In a study on the effectiveness of cupping massage in patients with chronic neck pain, one patient showed a formation of a lipoma in the cupping area after the first treatment session. Because of the short time interval between therapy and development of the lipoma, a primary cause is not realistic. This adverse event has not been described in the literature before, and the present report describes the case in summary.

  1. A confirmed case of toxic shock syndrome associated with the use of a menstrual cup

    OpenAIRE

    Mitchell, Michael A; Bisch, Steve; Arntfield, Shannon; Hosseini-Moghaddam, Seyed M

    2015-01-01

    Menstrual cups have been reported to be an acceptable substitute for tampons. These flexible cups have also been reported to provide a sustainable solution to menstrual management, with modest cost savings and no significant health risk. The present article documents the first case of toxic shock syndrome associated with the use of a menstrual cup in a woman 37 years of age, using a menstrual cup for the first time. Toxic shock syndrome and the literature on menstrual cups is reviewed and a p...

  2. A confirmed case of toxic shock syndrome associated with the use of a menstrual cup.

    Science.gov (United States)

    Mitchell, Michael A; Bisch, Steve; Arntfield, Shannon; Hosseini-Moghaddam, Seyed M

    2015-01-01

    Menstrual cups have been reported to be an acceptable substitute for tampons. These flexible cups have also been reported to provide a sustainable solution to menstrual management, with modest cost savings and no significant health risk. The present article documents the first case of toxic shock syndrome associated with the use of a menstrual cup in a woman 37 years of age, using a menstrual cup for the first time. Toxic shock syndrome and the literature on menstrual cups is reviewed and a possible mechanism for the development of toxic shock syndrome in the patient is described.

  3. [Study on standardization of cupping technique: elucidation on the establishment of the National Standard Standardized Manipulation of Acupuncture and Moxibustion, Part V, Cupping].

    Science.gov (United States)

    Gao, Shu-zhong; Liu, Bing

    2010-02-01

    From the aspects of basis, technique descriptions, core contents, problems and solutions, and standard thinking in standard setting process, this paper states experiences in the establishment of the national standard Standardized Manipulation of Acupuncture and Moxibustion, Part V, Cupping, focusing on methodologies used in cupping standard setting process, the method selection and operating instructions of cupping standardization, and the characteristics of standard TCM. In addition, this paper states the scope of application, and precautions for this cupping standardization. This paper also explaines tentative ideas on the research of standardized manipulation of acupuncture and moxibustion.

  4. [Osteosynthesis and cup revision in periprosthetic acetabulum fractures using a Kocher-Langenbeck approach].

    Science.gov (United States)

    Schwabe, P; Märdian, S; Perka, C; Schaser, K-D

    2016-04-01

    Reconstruction/stable fixation of the acetabular columns to create an adequate periacetabular requirement for the implantation of a revision cup. Displaced/nondisplaced fractures with involvement of the posterior column. Resulting instability of the cup in an adequate bone stock situation. Periprosthetic acetabulum fractures with inadequate bone stock. Extended periacetabular defects with loss of anchorage options. Isolated periprosthetic fractures of the anterior column. Septic loosening. Dorsal approach. Dislocation of hip. Mechanical testing of inlaying acetabular cup. With unstable cup situation explantation of the cup, fracture fixation of acetabulum with dorsal double plate osteosynthesis along the posterior column. Cup revision. Hip joint reposition. Early mobilization; partial weight bearing for 12 weeks. Thrombosis prophylaxis. Clinical and radiological follow-ups. Periprosthetic acetabular fracture in 17 patients with 9 fractures after primary total hip replacement (THR), 8 after revision THR. Fractures: 12 due to trauma, 5 spontaneously; 7 anterior column fractures, 5 transverse fractures, 4 posterior column fractures, 1 two column fracture after hemiendoprosthesis. 5 type 1 fractures and 12 type 2 fractures. Operatively treated cases (10/17) received 3 reinforcement ring, 2 pedestal cup, 1 standard revision cup, cup-1 cage construct, 1 ventral plate osteosynthesis, 1 dorsal plate osteosynthesis, and 1 dorsal plate osteosynthesis plus cup revision (10-month Harris Hip Score 78 points). Radiological follow-up for 10 patients: consolidation of fractures without dislocation and a fixed acetabular cup. No revision surgeries during follow-up; 2 hip dislocations, 1 transient sciatic nerve palsy.

  5. Clinical research evidence of cupping therapy in China: a systematic literature review.

    Science.gov (United States)

    Cao, Huijuan; Han, Mei; Li, Xun; Dong, Shangjuan; Shang, Yongmei; Wang, Qian; Xu, Shu; Liu, Jianping

    2010-11-16

    Though cupping therapy has been used in China for thousands of years, there has been no systematic summary of clinical research on it.This review is to evaluate the therapeutic effect of cupping therapy using evidence-based approach based on all available clinical studies. We included all clinical studies on cupping therapy for all kinds of diseases. We searched six electronic databases, all searches ended in December 2008. We extracted data on the type of cupping and type of diseases treated. 550 clinical studies were identified published between 1959 and 2008, including 73 randomized controlled trials (RCTs), 22 clinical controlled trials, 373 case series, and 82 case reports. Number of RCTs obviously increased during past decades, but the quality of the RCTs was generally poor according to the risk of bias of the Cochrane standard for important outcome within each trials. The diseases in which cupping was commonly employed included pain conditions, herpes zoster, cough or asthma, etc. Wet cupping was used in majority studies, followed by retained cupping, moving cupping, medicinal cupping, etc. 38 studies used combination of two types of cupping therapies. No serious adverse effects were reported in the studies. According to the above results, quality and quantity of RCTs on cupping therapy appears to be improved during the past 50 years in China, and majority of studies show potential benefit on pain conditions, herpes zoster and other diseases. However, further rigorous designed trials in relevant conditions are warranted to support their use in practice.

  6. Estimating Trabecular Bone Mechanical Properties From Non-Invasive Imaging

    Science.gov (United States)

    Hogan, Harry A.; Webster, Laurie

    1997-01-01

    An important component in developing countermeasures for maintaining musculoskeletal integrity during long-term space flight is an effective and meaningful method of monitoring skeletal condition. Magnetic resonance imaging (MRI) is an attractive non-invasive approach because it avoids the exposure to radiation associated with X-ray based imaging and also provides measures related to bone microstructure rather than just density. The purpose of the research for the 1996 Summer Faculty Fellowship period was to extend the usefulness of the MRI data to estimate the mechanical properties of trabecular bone. The main mechanical properties of interest are the elastic modulus and ultimate strength. Correlations are being investigated between these and fractal analysis parameters, MRI relaxation times, apparent densities, and bone mineral densities. Bone specimens from both human and equine donors have been studied initially to ensure high-quality MR images. Specimens were prepared and scanned from human proximal tibia bones as well as the equine distal radius. The quality of the images from the human bone appeared compromised due to freezing artifact, so only equine bone was included in subsequent procedures since these specimens could be acquired and imaged fresh before being frozen. MRI scans were made spanning a 3.6 cm length on each of 5 equine distal radius specimens. The images were then sent to Dr. Raj Acharya of the State University of New York at Buffalo for fractal analysis. Each piece was cut into 3 slabs approximately 1.2 cm thick and high-resolution contact radiographs were made to provide images for comparing fractal analysis with MR images. Dual energy X-ray absorptiometry (DEXA) scans were also made of each slab for subsequent bone mineral density determination. Slabs were cut into cubes for mechanical using a slow-speed diamond blade wafering saw (Buehler Isomet). The dimensions and wet weights of each cube specimen were measured and recorded. Wet weights

  7. Mandibular trabecular bone as fracture indicator in 80-year-old men and women.

    Science.gov (United States)

    Hassani-Nejad, Azar; Ahlqwist, Margareta; Hakeberg, Magnus; Jonasson, Grethe

    2013-12-01

    The objective of the present study was to compare assessments of the mandibular bone as fracture risk indicators for 277 men and women. The mandibular trabecular bone was evaluated in periapical radiographs, using a visual index, as dense, mixed dense and sparse, or sparse. Bone texture was analysed using a computer-based method in which the number of transitions from trabeculae to intertrabecular spaces was calculated. The sum of the sizes and intensities of the spaces between the trabeculae was calculated using Jaw-X software. Women had a statistically significantly greater number of fractures and a higher frequency of sparse mandibular bone. The OR for having suffered a fracture with visually sparse trabecular bone was highest for the male group (OR = 5.55) and lowest for the female group (OR = 3.35). For bone texture as an indicator of previous fracture, the OR was significant for the female group (OR = 2.61) but not for the male group, whereas the Jaw-X calculations did not differentiate between fractured and non-fractured groups. In conclusion, all bone-quality assessments showed that women had a higher incidence of sparse trabecular bone than did men. Only the methods of visual assessment and trabecular texture were significantly correlated with previous bone fractures. © 2013 Eur J Oral Sci.

  8. Effects of deleting cannabinoid receptor-2 on mechanical and material properties of cortical and trabecular bone

    Directory of Open Access Journals (Sweden)

    Aysha B. Khalid

    2015-12-01

    Full Text Available Cnr2 is one of two cannabinoid receptors known to regulate bone metabolism. Here, we compared the whole bone properties of femora and tibiae from three-month-old Cnr2−/- mice with wild-type controls using a C57BL/6 background. Bending stiffness was measured by three-point bending. The elastic modulus, density and mineral content were measured using ultrasound, Archimedes’ principle and ashing. Micro-CT was used to measure the second moment of area, inner and outer perimeters of the cortical shaft and trabecular parameters. Deleting Cnr2 increased the bending stiffness by increasing the second moment of area. Bone from affected male mice had a greater modulus than controls, although no difference was observed in females. The fractional volume of trabecular bone was greater in Cnr2−/- females than controls, while no difference was seen in males. These data indicate that inactivating Cnr2 increases the amount of cortical bone in both males and females at 3 months of age, but the effect on trabecular bone is different in the two sexes. These findings extend previous studies looking only at trabecular bone and provide further support for the possible use of Cnr2 antagonists for improving bone properties that may be of value in the treatment of bone disorders.

  9. Preliminary report of cells at risk at the bone surface in trabecular bone

    International Nuclear Information System (INIS)

    Jee, W.S.S.; Wronski, T.J.; Kimmel, D.B.; Dell, R.B.; Johnson, F.

    1975-01-01

    This is a report of some early work on the cells at risk portion of the dynamic microanatomical dosimetry program of the Bone Group. The cells lining the trabecular bone of thoracic vertebral bodies from beagles aged 568, 2942, 4117, 4277, 4629, and 4801 days were characterized. Histologic and sampling experience gained in this attempt indicates that further improvements are needed

  10. Velocity dispersion in trabecular bone: influence of multiple scattering and of absorption.

    Science.gov (United States)

    Haïat, G; Lhémery, A; Renaud, F; Padilla, F; Laugier, P; Naili, S

    2008-12-01

    Speed of sound measurements are widely used clinically to assess bone strength. Trabecular bone is an attenuating composite material in which negative values of velocity dispersion have been measured, this behavior remaining poorly explained physically. The aim of this work is to describe the ultrasonic propagation in trabecular bone modeled by infinite cylinders immersed in a saturating matrix, and to derive the physical determinants of velocity dispersion. A homogenization model accounting for the coupling of multiple scattering and absorption phenomena allows the computation of phase velocity and of dispersion while varying bone properties. The present model is adapted from the generalized self-consistent method developed in the work of Yang and Mal [(1994). "Multiple-scattering of elastic waves in a fiber-reinforced composite," J. Mech. Phys. Solids 42, 1945-1968]. It predicts negative values of velocity dispersion, in agreement with experimental results obtained in phantoms mimicking trabecular bone. In trabecular bone, mostly negative and also positive values of velocity dispersion are predicted by the model, which span within the range of values measured experimentally. Scattering effects are responsible for the negative values of dispersion, whereas the frequency dependence of the absorption coefficient in bone marrow and/or in the trabeculae results in an increase in dispersion, which may then become positive.

  11. Multi-axial fatigue of trabecular bone with respect to normal walking

    CERN Document Server

    Mostakhdemin, Mohammad; Syahrom, Ardiyansyah

    2016-01-01

    This book focuses on the analysis and treatment of osteoporotic bone based on drug administration, tracking fatigue behavior and taking into consideration the mechanical interaction of implants with trabecular bone. Weak trabeculae are one of the most important clinical features that need to be addressed in order to prevent hip joint fractures.

  12. Evaluation of the mechanical properties of human iliac trabecular bone using finite element analysis

    International Nuclear Information System (INIS)

    Kohno, Jun; Ito, Masako; Kohno, Mika; Nakata, Tomoko; Furuyama, Kiyotaka; Habu, Takeshi

    2001-01-01

    Human iliac trabecular bone specimens were scanned using micro-computed tomography to obtain volume data of two-dimensional images in post-menopausal women, and two- and three-dimensional morphometric parameters, such as trabecular bone volume/tissue volume, trabecular thickness, structure model index, and trabecular bone pattern factor, were calculated using these image data. We developed several image processing programs for fast, easy operation. The contents of the image processing programs include changing of image resolution and image size, thresholding value, filtering, labeling, and division into elements. Several processings of the same image data were performed for the finite element analysis (FEA). Based on results of the degree of anisotropy, the bone structure was loaded in three directions, x-, y-, and z-axes. The images of the stress distribution and yield strength obtained from the three axis directions differed depending on load direction, and the correlations of yield strength with the variousmic rostructural parameters also differed depending on load direction. Load direction in vivo should be considered for bone specimens in FEA analysis. (author)

  13. Translimbal laser photocoagulation to the trabecular meshwork as a model of glaucoma in rats.

    Science.gov (United States)

    Levkovitch-Verbin, Hana; Quigley, Harry A; Martin, Keith R G; Valenta, Danielle; Baumrind, Lisa A; Pease, Mary Ellen

    2002-02-01

    To develop and characterize a model of pressure-induced optic neuropathy in rats. Experimental glaucoma was induced unilaterally in 174 Wistar rats, using a diode laser with wavelength of 532 nm aimed at the trabecular meshwork and episcleral veins (combination treatment group) or only at the trabecular meshwork (trabecular group) through the external limbus. Intraocular pressure (IOP) was measured by a tonometer in rats under ketamine-xylazine anesthesia. Possible retinal vascular compromise was evaluated by repeated fundus examinations and by histology. The degree of retinal ganglion cell (RGC) loss was assessed by a masked, semiautomated counting of optic nerve axons. Effects of laser treatment on anterior ocular structures and retina were judged by light microscopy. After the laser treatment, IOP was increased in all eyes to higher than the normal mean IOP of 19.4 +/- 2.1 mm Hg (270 eyes). Peak IOP was 49.0 +/- 6.1 mm Hg (n = 108) in the combination group that was treated by a laser setting of 0.7 seconds and 0.4 W and 34.0 +/- 5.7 mm Hg (n = 46) in the trabecular group. Mean IOP after 6 weeks was 25.5 +/- 2.9 mm Hg in glaucomatous eyes in the combination group compared with 22.0 +/- 1.8 mm Hg in the trabecular group. IOP in the glaucomatous eyes was typically higher than in the control eyes for at least 3 weeks. In the combination group, RGC loss was 16.1% +/- 14.4% at 1 week (n = 8, P = 0.01), 59.7% +/- 25.7% at 6 weeks (n = 88, P < 0.001), and 70.9% +/- 23.6% at 9 weeks (n = 12, P < 0.001). The trabecular group had mean axonal loss of 19.1% +/- 14.0% at 3 weeks (n = 9, P = 0.004) and 24.3% +/- 20.2% at 6 weeks (n = 25, P < 0.001), increasing to 48.4% +/- 32.8% at 9 weeks (n = 12, P < 0.001). Laser treatment led to closure of intertrabecular spaces and the major outflow channel. The retina and choroid were normal by ophthalmoscopy at all times after treatment. Light microscopic examination showed only loss of RGCs and their nerve fibers. Increased IOP caused

  14. Faraday cup dosimetry in a proton therapy beam without collimation

    International Nuclear Information System (INIS)

    Grusell, Erik; Isacsson, Ulf; Montelius, Anders; Medin, Joakim

    1995-01-01

    A Faraday cup in a proton beam can give an accurate measurement of the number of protons collected by the cup. It is shown that the collection efficiency with a proper design can be close to unity. To be able to calibrate an ionization chamber from such a measurement, as is recommended in some dosimetry protocols, the energy spectrum of the proton beam must be accurately known. This is normally not the case when the lateral beam extension is defined by collimators. Therefore a method for relating an ionization chamber measurement in an uncollimated beam to the total number of protons in the beam has been developed and is described together with experimental results from calibrating an ionization chamber using this method in the therapeutic beam in Uppsala. This method is applicable to ionization chambers of any shape and the accuracy is estimated to be 1.6% (1 SD). (Author)

  15. [Mountainbike injuries in world-cup and recreational athletes].

    Science.gov (United States)

    Himmelreich, H; Pralle, H; Vogt, L; Banzer, W

    2007-12-01

    This study investigated the incidence and frequency of injuries in mountainbike sports among competitive and recreational athletes. In a retrospective study design mountain-bike athletes were interviewed by means of a standardized questionnaire with regard to sports injuries and damages within the previous two years. The evaluation of time relative injury-rate was carried out under consideration of class and competition discipline. 75 % of the distributed questionnaires returned completed by 106 World-Cup (39 female symbol 67 male symbol, 23.1 y) and 134 recreational athletes (17 female symbol 117 male symbol, 27.4 y). Approximately 80 % of the World-Cup and about 50 % of the recreational athletes reported about at least one severe injury. World-Cup downhill athletes (1.08 injuries/ 1000 h) show a more than doubled time-related injury-rate in comparison with Cross-Country athletes (0.39 injuries/ 1000 h). Injuries of the lower (47 vs. 35 %) and upper extremity (40 vs. 41 %) show comparable prevalence for competitive and recreational cyclists. In the group of recreational athletes open wounds dominate, competitive athletes demonstrate a significant higher fracture-rate (p athletes head injuries stand out (n = 40). Although World-Cup participation does not result in essential injury-increase, the downhill discipline is characterized by a higher injury risk. Presumably in view of the performance orientation, there is a higher degree of risk readiness. Despite the riding performance and the obligatory safety equipment a remarkable number of bone and head injuries results.

  16. Brazilian World cup 2014: Terrorism, tourism, and social conflict

    OpenAIRE

    Tzanelli, R; Korstanje, M; Clayton, A

    2014-01-01

    The World cup transcends the interests of culture and nations worldwide. Every 4 years, delegations from the four corners of the world compete for a month. The mass tourist demand an event of this caliber generates prompts policy makers and tourism scholars to devote considerable time in planning in detail the infrastructure and service industry for the benefit of incomers. Unfortunately, in areas of the world plagued by political instability, some groups may use the media events to communica...

  17. Gene expression profile of human trabecular meshwork cells in response to long-term dexamethasone exposure.

    Science.gov (United States)

    Rozsa, Frank W; Reed, David M; Scott, Kathleen M; Pawar, Hemant; Moroi, Sayoko E; Kijek, Theresa Guckian; Krafchak, Charles M; Othman, Mohammad I; Vollrath, Douglas; Elner, Victor M; Richards, Julia E

    2006-02-27

    Topical use of dexamethasone has long been associated with steroid induced-glaucoma, although the mechanism is unknown. We applied a strict filtering of comparative microarray data to more than 18,000 genes to evaluate global gene expression of cultured human trabecular meshwork cells in response to treatment with dexamethasone. Three human trabecular meshwork cell primary cultures from nonglaucomatous donors were incubated with and without dexamethasone for 21 days. Relative gene expression was evaluated by analysis of U133A GeneChip and the results validated using quantitative polymerase chain reaction (PCR). Application of strict filtering to include only genes with statistically significant differences in gene expression across all three trabecular meshwork cell cultures produced a list of 1,260 genes. Significant changes in signal level were observed, including 23 upregulated and 18 downregulated genes that changed greater than three fold in each of three cell cultures. Using quantitative PCR we found changes greater than a thousand fold for two genes (SLP1 and SAA2) and changes greater than a hundred fold for another five genes (ANGPTL7, MYOC, SAA1, SERPINA3, and ZBTB16). Expression changes in trabecular meshwork cells in response to dexamethasone treatment indicate that a group of actins and actin-associated proteins are involved in the development of cross-linked actin networks that form in response to dexamethasone. A trend was identified toward decreased expression of protease genes accompanied by an increased expression of protease inhibitors. Such a trend in nonproteasomal proteolysis conceivably affects gene product levels above the level of transcription. Only two genes, MYOC and IGFBP2, showed significantly elevated expression after dexamethasone treatment in our study and the other three previously published reports of primary culture trabecular meshwork cell gene expression.

  18. Experimental erbium: YAG laser photoablation of trabecular meshwork in rabbits: an in-vivo study.

    Science.gov (United States)

    Dietlein, T S; Jacobi, P C; Schröder, R; Krieglstein, G K

    1997-05-01

    Photoablative laser trabecular surgery has been proposed as an outflow-enhancing treatment for open-angle glaucoma. The aim of the study was to investigate the time course of repair response following low-thermal Erbium: YAG laser trabecular ablation. In 20 anaesthetized rabbits gonioscopically controlled ab-interno photoablation of the ligamenta pectinata and underlying trabecular meshwork (TM) was performed with a single-pulsed (200 microseconds) Erbium: YAG (2.94 microns) laser. The right eye received 12-15 single laser pulses (2 mJ) delivered through an articulated zirconium fluoride fiberoptic and a 200 microns (core diameter) quartz fiber tip, the left unoperated eye served as control. At time intervals of 30 minutes, 2, 10, 30, and 60 days after laser treatment, eyes were processed for light- and scanning electron microscopy. The applied energy density of 6-4 J cm-2 resulted in visible dissection of the ligamenta pectinata and reproducible microperforations of the TM exposing scleral tissue accompanied by blood reflux from the aqueous plexus. The initial ablation zones measured 154 +/- 36 microns in depth and 45 +/- 6 microns in width. Collateral thermal damage zones were 22 +/- 8 microns. At two days post-operative, ablation craters were still blood- and fibrin-filled. The inner surface of the craters were covered with granulocytes. No cellular infiltration of the collateral thermal damage zone was observed. At 10 days post-operative, progressive fibroblastic proliferation was observed, resulting in dense scar tissue formation with anterior synechiae, proliferating capillaries and loss of intertrabecular spaces inside the range of former laser treatment at 60 days post-operative. Trabecular microperforations were closed 60 days after laser treatment in all rabbits. IOP in treated and contralateral eyes did not significantly change its level during whole period of observation. Low-thermal infrared laser energy with minimal thermal damage to collateral

  19. Enterovaginal or Vesicovaginal Fistula Control Using a Silicone Cup.

    Science.gov (United States)

    Russell, Katie W; Robinson, Ryan E; Mone, Mary C; Scaife, Courtney L

    2016-12-01

    An enterovaginal or vesicovaginal fistula is a complication resulting in vaginal discharge of succus, urine, or stool that can lead to significant complications. For low-volume fistulae, tampons or pads may be used. With high-volume fistulae, frequent product change can be painful and unpredictable in terms of efficacy. The psychologic distress is profound. Surgery may not be an option, making symptom control the priority. We report the use of a reusable menstrual silicone vaginal cup placed to divert and contain drainage. The menstrual cup provided significant symptom relief. Drainage is immediately diverted from tissue, unlike with tampon or pad use, which involves longer contact periods with caustic fluids. A system was created by adapting the end of the cup by adding silastic tubing and an external leg bag to provide long-term drainage control. Improvement in quality of life is of primary importance when dealing with fistula drainage. This simple and inexpensive device should be considered in those cases in which the drainage can be diverted as a viable option, especially in those who are symptomatic and awaiting surgical repair or in those for whom surgery cannot be performed.

  20. Incorporating tissue anisotropy and heterogeneity in finite element models of trabecular bone altered predicted local stress distributions.

    Science.gov (United States)

    Hammond, Max A; Wallace, Joseph M; Allen, Matthew R; Siegmund, Thomas

    2018-04-01

    Trabecular bone is composed of organized mineralized collagen fibrils, which results in heterogeneous and anisotropic mechanical properties at the tissue level. Recently, biomechanical models computing stresses and strains in trabecular bone have indicated a significant effect of tissue heterogeneity on predicted stresses and strains. However, the effect of the tissue-level mechanical anisotropy on the trabecular bone biomechanical response is unknown. Here, a computational method was established to automatically impose physiologically relevant orientation inherent in trabecular bone tissue on a trabecular bone microscale finite element model. Spatially varying tissue-level anisotropic elastic properties were then applied according to the bone mineral density and the local tissue orientation. The model was used to test the hypothesis that anisotropy in both homogeneous and heterogeneous models alters the predicted distribution of stress invariants. Linear elastic finite element computations were performed on a 3 mm cube model isolated from a microcomputed tomography scan of human trabecular bone from the distal femur. Hydrostatic stress and von Mises equivalent stress were recorded at every element, and the distributions of these values were analyzed. Anisotropy reduced the range of hydrostatic stress in both tension and compression more strongly than the associated increase in von Mises equivalent stress. The effect of anisotropy was independent of the spatial redistribution high compressive stresses due to tissue elastic heterogeneity. Tissue anisotropy and heterogeneity are likely important mechanisms to protect bone from failure and should be included for stress analyses in trabecular bone.

  1. Does skeletal anatomy reflect adaptation to locomotor patterns? Cortical and trabecular architecture in human and nonhuman anthropoids.

    Science.gov (United States)

    Shaw, Colin N; Ryan, Timothy M

    2012-02-01

    Although the correspondence between habitual activity and diaphyseal cortical bone morphology has been demonstrated for the fore- and hind-limb long bones of primates, the relationship between trabecular bone architecture and locomotor behavior is less certain. If sub-articular trabecular and diaphyseal cortical bone morphology reflects locomotor patterns, this correspondence would be a valuable tool with which to interpret morphological variation in the skeletal and fossil record. To assess this relationship, high-resolution computed tomography images from both the humeral and femoral head and midshaft of 112 individuals from eight anthropoid genera (Alouatta, Homo, Macaca, Pan, Papio, Pongo, Trachypithecus, and Symphalangus) were analyzed. Within-bone (sub-articular trabeculae vs. mid-diaphysis), between-bone (forelimb vs. hind limb), and among-taxa relative distributions (femoral:humeral) were compared. Three conclusions are evident: (1) Correlations exists between humeral head sub-articular trabecular bone architecture and mid-humerus diaphyseal bone properties; this was not the case in the femur. (2) In contrast to comparisons of inter-limb diaphyseal bone robusticity, among all species femoral head trabecular bone architecture is significantly more substantial (i.e., higher values for mechanically relevant trabecular bone architectural features) than humeral head trabecular bone architecture. (3) Interspecific comparisons of femoral morphology relative to humeral morphology reveal an osteological "locomotor signal" indicative of differential use of the forelimb and hind limb within mid-diaphysis cortical bone geometry, but not within sub-articular trabecular bone architecture. Copyright © 2011 Wiley Periodicals, Inc.

  2. Central X-ray beam correction of radiographic acetabular cup measurement after THA: an experimental study.

    Science.gov (United States)

    Schwarz, T; Weber, M; Wörner, M; Renkawitz, T; Grifka, J; Craiovan, B

    2017-05-01

    Accurate assessment of cup orientation on postoperative radiographs is essential for evaluating outcome after THA. However, accuracy is impeded by the deviation of the central X-ray beam in relation to the cup and the impossibility of measuring retroversion on standard pelvic radiographs. In an experimental trial, we built an artificial cup holder enabling the setting of different angles of anatomical anteversion and inclination. Twelve different cup orientations were investigated by three examiners. After comparing the two methods for radiographic measurement of the cup position developed by Lewinnek and Widmer, we showed how to differentiate between anteversion and retroversion in each cup position by using a second plane. To show the effect of the central beam offset on the cup, we X-rayed a defined cup position using a multidirectional central beam offset. According to Murray's definition of anteversion and inclination, we created a novel corrective procedure to balance measurement errors caused by deviation of the central beam. Measurement of the 12 different cup positions with the Lewinnek's method yielded a mean deviation of [Formula: see text] (95 % CI 1.3-2.3) from the original cup anteversion. The respective deviation with the Widmer/Liaw's method was [Formula: see text] (95 % CI 2.4-4.0). In each case, retroversion could be differentiated from anteversion with a second radiograph. Because of the multidirectional central beam offset ([Formula: see text] cm) from the acetabular cup in the cup holder ([Formula: see text] anteversion and [Formula: see text] inclination), the mean absolute difference for anteversion was [Formula: see text] (range [Formula: see text] to [Formula: see text] and [Formula: see text] (range [Formula: see text] to [Formula: see text] for inclination. The application of our novel mathematical correction of the central beam offset reduced deviation to a mean difference of [Formula: see text] for anteversion and [Formula: see text

  3. Revision total knee arthroplasty with the use of trabecular metal cones

    DEFF Research Database (Denmark)

    Jensen, Claus L; Petersen, Michael Mygind; Schrøder, Henrik

    2012-01-01

    analysis at 24 months showed the same net direction of rotation for the groups around the y-, z-axis and around the x-, y-axis for translation. Tibial revision implants with TM Cone result in an early stable situation with less irregular migration pattern than revision without TM Cone....... Orthopaedic Research Institute bone loss classification and NexGen revision system were used. Radiostereometric analysis was performed with 24 months of follow-up. Maximum total point motion: stable migration was seen in the TM Cone group. No statistically significant difference was found. Segment motion...

  4. World soccer cup as a trigger of cardiovascular events.

    Science.gov (United States)

    Borges, Daniel Guilherme Suzuki; Monteiro, Rosane Aparecida; Schmidt, André; Pazin-Filho, Antonio

    2013-06-01

    Acute coronary syndromes are the major cause of death in Brazil and in the world. External stimuli, known also as triggers, such as emotional state and activity, may generate physiopathological changes that can trigger acute coronary syndromes. Among the studied triggers, the impact of stressful events, such as soccer championships, are controversial in literature and there is no effective data on the Brazilian population. To evaluate the acute effects of environmental stress induced by soccer games of the World Soccer Cup on increased incidence of cardiovascular diseases in Brazil. Public data were obtained from the Unified Health System (Sistema Único de Saúde), regarding hospital admissions that had the International Code Disease of acute coronary syndromes from May to August, in 1998, 2002, 2006 and 2010 (155,992 admissions). Analysis was restricted to patients older than 35 years and admitted by clinical specialties. The incidence of myocardial infarction, angina and mortality were compared among days without World Cup soccer games (Group I: 144,166; 61.7 ± 12.3; 59.4% males); on days when there were no Brazil's soccer team matches (Group II: 9,768; 61.8 ± 12.3; 60.0% males); and days when there were Brazil's soccer team matches (Group III; 2,058; 61.6 ± 12.6; 57.8% males). Logistic regression was used to adjust to age, gender, population density and number of medical assistance units. The incidence of myocardial infarction increased during the period of World Cup soccer games (1.09; 95%CI = 1.05-1.15) and days when there were Brazil's matches (1.16; 95%CI = 1.06-1.27). There was no impact on mortality during the Cup (1.00; CI 95% = 0.93-1.08) and Brazil's matches (1.04; 95%CI = 0.93-1.22). World Cup soccer games and, specially, Brazil's matches have an impact on the incidence of myocardial infarction, but not on in-hospital mortality.

  5. Diagnosis of osteoarthritis and prognosis of tibial cartilage loss by quantification of tibia trabecular bone from MRI

    DEFF Research Database (Denmark)

    Marques, Joselene; Genant, Harry K.; Lillholm, Martin

    2013-01-01

    A longitudinal study was used to investigate the quantification of osteoarthritis and prediction of tibial cartilage loss by analysis of the tibia trabecular bone from magnetic resonance images of knees. The Kellgren Lawrence (KL) grades were determined by radiologists and the levels of cartilage...... loss were assessed by a segmentation process. Aiming to quantify and potentially capture the structure of the trabecular bone anatomy, a machine learning approach used a set of texture features for training a classifier to recognize the trabecular bone of a knee with radiographic osteoarthritis. Using...

  6. The role of fabric in the large strain compressive behavior of human trabecular bone.

    Science.gov (United States)

    Charlebois, Mathieu; Pretterklieber, Michael; Zysset, Philippe K

    2010-12-01

    Osteoporosis-related vertebral body fractures involve large compressive strains of trabecular bone. The small strain mechanical properties of the trabecular bone such as the elastic modulus or ultimate strength can be estimated using the volume fraction and a second order fabric tensor, but it remains unclear if similar estimations may be extended to large strain properties. Accordingly, the aim of this work is to identify the role of volume fraction and especially fabric in the large strain compressive behavior of human trabecular bone from various anatomical locations. Trabecular bone biopsies were extracted from human T12 vertebrae (n=31), distal radii (n=43), femoral head (n=44), and calcanei (n=30), scanned using microcomputed tomography to quantify bone volume fraction (BV/TV) and the fabric tensor (M), and tested either in unconfined or confined compression up to very large strains (∼70%). The mechanical parameters of the resulting stress-strain curves were analyzed using regression models to examine the respective influence of BV/TV and fabric eigenvalues. The compressive stress-strain curves demonstrated linear elasticity, yielding with hardening up to an ultimate stress, softening toward a minimum stress, and a steady rehardening followed by a rapid densification. For the pooled experiments, the average minimum stress was 1.89 ± 1.77 MPa, while the corresponding mean strain was 7.15 ± 1.84%. The minimum stress showed a weaker dependence with fabric as the elastic modulus or ultimate strength. For the confined experiments, the stress at a logarithmic strain of 1.2 was 8.08 ± 7.91 MPa, and the dissipated energy density was 5.67 ± 4.42 MPa. The latter variable was strongly related to the volume fraction (R(2)=0.83) but the correlation improved only marginally with the inclusion of fabric (R(2)=0.84). The influence of fabric on the mechanical properties of human trabecular bone decreases with increasing strain, while the role of volume fraction remains

  7. Structure model index does not measure rods and plates in trabecular bone

    Directory of Open Access Journals (Sweden)

    Phil L Salmon

    2015-10-01

    Full Text Available Structure model index (SMI is widely used to measure rods and plates in trabecular bone. It exploits the change in surface curvature that occurs as a structure varies from spherical (SMI = 4, to cylindrical (SMI = 3 to planar (SMI = 0. The most important assumption underlying SMI is that the entire bone surface is convex and that the curvature differential is positive at all points on the surface. The intricate connections within the trabecular continuum suggest that a high proportion of the surface could be concave, violating the assumption of convexity and producing regions of negative differential. We implemented SMI in the BoneJ plugin and included the ability to measure the amounts of surface that increased or decreased in area after surface mesh dilation, and the ability to visualize concave and convex regions. We measured SMI and its positive (SMI+ and negative (SMI- components, bone volume fraction (BV/TV, the fraction of the surface that is concave (CF, and mean ellipsoid factor (EF in trabecular bone using 38 X-ray microtomography (XMT images from a rat ovariectomy model of sex steroid rescue of bone loss, and 169 XMT images from a broad selection of 87 species' femora (mammals, birds, and a crocodile. We simulated bone resorption by eroding an image of elephant trabeculae and recording SMI and BV/TV at each erosion step. Up to 70%, and rarely less than 20%, of the trabecular surface is concave (CF 0.155 – 0.700. SMI is unavoidably influenced by aberrations from SMI-, which is strongly correlated with BV/TV and CF. The plate-to-rod transition in bone loss is an erroneous observation resulting from SMI's close and artefactual relationship with BV/TV. SMI cannot discern between the distinctive trabecular geometries typical of mammalian and avian bone, whereas EF clearly detects birds' more plate-like trabeculae. EF is free from confounding relationships with BV/TV and CF. SMI results reported in the literature should be treated with

  8. Qualidade da bebida do café Icatu Coffee cup quality - cup quality variabiltty in the Icatu cultivar

    Directory of Open Access Journals (Sweden)

    L. C. Fazuoli

    1977-01-01

    Full Text Available Analisaram-se as características da bebida de alguns cafeeiros híbridos (Coffea arabica x C. canephora que deram origem ao icatu, e de plantas pertencentes a nove populações deste cultivar. A qualidade da bebida dos cafeeiros originais mostrou-se semelhante à do arábica, variando de "mole" a "apenas mole". Nas populações de icatu foram efetuadas 1953 determinações. Verificou-se que a bebida não difere daquela produzida pelo cultivar acaiá (C. arabica, tomada como padrão. Em escala de cinco pontos, 63 (3,2% determinações deram bebida "dura" e 1324 (67,8%, "mole", enquanto o acaiá apresentou bebida "mole". Na escala de 10 pontos o número 3 foi dado a nove determinações (0,5% e o máximo de nove pontos a 677 (34,6%, sendo de 7,7 a média de pontos conferida ao acaiá. Verificou-se que as populações H 3849-7, H 3851-4 e H 4782-7 apresentaram médias de pontos mais elevadas e que as populações H 3849-14-2 e H 3849-14-3 deram as menores médias, nas duas escalas de valores. As populações examinadas não diferem do acaiá quanto à qualidade da bebida, podendo ser utilizadas comercialmente.Cup quality determination was undertaken for a group of coffee seed samples of interespecific (Coffea arabica x C. canephora trees, which gave rise to the Icatu cultivar and also for nine Icatu coffee populations. The original hybrid plants showed cup quality similar to the Arabica control, with exception of one single plant which gave lower quality. For these populations a total of 1953 cup quality determinations were made by three independent coffee drinker experts. Two scale ranking from 0-5 and 1-10 were used for the evaluation. It was verified that the average grades of each one of the nine Icatu populations did not differ from the Arabica. In the scale (0-5 the grade "Hard" occurred in 63 determinations (3.2% an the "Soft" cup quality in 1324 determinations (67.8%. In the 10 points scale 3 points were attributed to nine determinations

  9. Role of Cupping in the treatment of different diseases: systematic review article

    Directory of Open Access Journals (Sweden)

    Hussein Kheirandish

    2017-03-01

    Full Text Available Background: Cupping is one of the most common traditional medical procedures in Iran, which is widely used and prescribed from long time ago. Putting a cup on the skin with induction of negative pressure, causes an artificial inflammation with collection of some body fluids under the skin which can be extracted by scarification. Different mechanisms and effects are attributable to cupping based on several assumptions and theories. Regarding to the vast use of this traditional therapeutic method and relatively different point of views about the effects of cupping, this study was performed to systematically assess published studies in this field and also to find probable indications of cupping. Methods: In this systematic review, according to search via Google Scholar, PubMed, Scopus databases and Iranian databases (IranMedex and SID, 99 different scientific articles about cupping and it`s positive and negative effects were assessed. Different diseases categorized in 19 groups according to the pathophysiology and organ similarities for better presentation Results: More than 50 different disorders have been studied in randomized or nonrandomized clinical trials. 84.9% of reviewed papers have reported significant positive effects of cupping. The most common disorders studied in the reviewed papers were musculoskeletal, pain and skin disorders, especially low back pain has been studied more with positive results of cupping. Conclusion: In Iran the prevalence of cupping performance is really high. The reported positive effects and also complications especially infection were also dramatic. It seems performing systematic studies on cupping effects in different disorders and designing and implementing an active surveillance system for cupping in our country is essential. According to the type of studies, authors concluded that cupping have been reported as an effective intervention for some diseases such as musculoskeletal and skin disorders, but

  10. Multiple data sets and modelling choices in a comparative LCA of disposable beverage cups.

    Science.gov (United States)

    van der Harst, Eugenie; Potting, José; Kroeze, Carolien

    2014-10-01

    This study used multiple data sets and modelling choices in an environmental life cycle assessment (LCA) to compare typical disposable beverage cups made from polystyrene (PS), polylactic acid (PLA; bioplastic) and paper lined with bioplastic (biopaper). Incineration and recycling were considered as waste processing options, and for the PLA and biopaper cup also composting and anaerobic digestion. Multiple data sets and modelling choices were systematically used to calculate average results and the spread in results for each disposable cup in eleven impact categories. The LCA results of all combinations of data sets and modelling choices consistently identify three processes that dominate the environmental impact: (1) production of the cup's basic material (PS, PLA, biopaper), (2) cup manufacturing, and (3) waste processing. The large spread in results for impact categories strongly overlaps among the cups, however, and therefore does not allow a preference for one type of cup material. Comparison of the individual waste treatment options suggests some cautious preferences. The average waste treatment results indicate that recycling is the preferred option for PLA cups, followed by anaerobic digestion and incineration. Recycling is slightly preferred over incineration for the biopaper cups. There is no preferred waste treatment option for the PS cups. Taking into account the spread in waste treatment results for all cups, however, none of these preferences for waste processing options can be justified. The only exception is composting, which is least preferred for both PLA and biopaper cups. Our study illustrates that using multiple data sets and modelling choices can lead to considerable spread in LCA results. This makes comparing products more complex, but the outcomes more robust. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. [Analysis on the adverse events of cupping therapy in the application].

    Science.gov (United States)

    Zhou, Xin; Ruan, Jing-wen; Xing, Bing-feng

    2014-10-01

    The deep analysis has been done on the cases of adverse events and common injury of cupping therapy encountered in recent years in terms of manipulation and patient's constitution. The adverse events of cupping therapy are commonly caused by improper manipulation of medical practitioners, ignoring contraindication and patient's constitution. Clinical practitioners should use cupping therapy cautiously, follow strictly the rules of standard manipulation and medical core system, pay attention to the contraindication and take strict precautions against the occurrence of adverse events.

  12. Efficacy of cupping therapy in patients with the fibromyalgia syndrome-a randomised placebo controlled trial

    OpenAIRE

    Lauche, Romy; Spitzer, Julia; Schwahn, Barbara; Ostermann, Thomas; Bernardy, Kathrin; Cramer, Holger; Dobos, Gustav; Langhorst, Jost

    2016-01-01

    This study aimed to test the efficacy of cupping therapy to improve symptoms and quality of life in patients diagnosed with the fibromyalgia syndrome. Participants were randomly assigned to cupping therapy, sham or usual care. Cupping was administered five times at twice weekly intervals on the upper and lower back. The primary outcome measure was pain intensity at day 18. Secondary outcomes included functional disability, quality of life, fatigue and sleep quality as well as pressure pain se...

  13. Köebner phenomenon induced by cupping therapy in a psoriasis patient.

    Science.gov (United States)

    Yu, Rui-Xing; Hui, Yun; Li, Cheng-Rang

    2013-06-15

    Psoriasis is a chronic, immune-mediated inflammatory and refractory disease. The koebner phenomenon, which can be induced by trauma, is common in psoriasis patients. Herein, we report a patient with psoriasis who was treated by cupping therapy and subsequently developed the koebner phenomenon (KP) at the cupped sites. To our knowledge, it is the first report about cupping therapy leading to KP in a psoriasis patient.

  14. The Cup'ik People of the Western Tundra: A Curriculum.

    Science.gov (United States)

    Pingayak, John

    The Cup'ik people are a group of Yup'ik Eskimos who live in southwest Alaska. This curriculum aims to enhance Cup'ik students' interest in their own culture by making that culture a part of their daily activities; to teach students to practice the traditional Cup'ik respect for elders, fellow students, and others in the community; and to teach…

  15. Red Resurrection : The Challenges Faced by Scandinavian Vendors when Marketing the Menstrual Cup

    OpenAIRE

    Coe-Björsell, Emily; Jansson, Linn

    2015-01-01

    It is argued in this thesis that the stigmatization of menstruation and the atypical product features of the menstrual cup constitute a unique marketing challenge for vendors of the menstrual cup. The purpose of this study is therefore to investigate these issues and the ways in which Scandinavian vendors approach them. Further, the possible effects of this approach on the rate of adoption of the menstrual cup are analyzed. In order to do so, interviews with four Scandinavian vendors of the m...

  16. Quantitative Evaluation of Trabecular Bone Structure by Calcaneus MR Images Texture Analysis of Healthy Volunteers and Osteoporotic Subjects

    National Research Council Canada - National Science Library

    Herlidou, S

    2001-01-01

    The aim of this study is to evaluate, in vivo, trabecular bone structure of the calcaneus of healthy volunteers and osteoporotic patients by texture analysis of MR images Automated methods of texture...

  17. Cupping regulates local immunomodulation to activate neural-endocrine-immune worknet.

    Science.gov (United States)

    Guo, Yang; Chen, Bo; Wang, Dong-Qiang; Li, Ming-Yue; Lim, Calista Hui-Min; Guo, Yi; Chen, Zelin

    2017-08-01

    Research on cupping therapy is lacking at home and abroad. However, cupping and acupuncture therapy are both surface stimulation therapies. This paper suggests the mechanism of cupping therapy and proposes that the same mechanism underlies both cupping and acupuncture therapy. The microenvironment is changed when stimulating the surface of the skin, and physical signals transform into biological signals, which also interact with each other in the body. These signalling cascades activate the neuroendocrine-immune system, which produces the therapeutic effect. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Efficacy of cupping therapy in patients with the fibromyalgia syndrome-a randomised placebo controlled trial.

    Science.gov (United States)

    Lauche, Romy; Spitzer, Julia; Schwahn, Barbara; Ostermann, Thomas; Bernardy, Kathrin; Cramer, Holger; Dobos, Gustav; Langhorst, Jost

    2016-11-17

    This study aimed to test the efficacy of cupping therapy to improve symptoms and quality of life in patients diagnosed with the fibromyalgia syndrome. Participants were randomly assigned to cupping therapy, sham or usual care. Cupping was administered five times at twice weekly intervals on the upper and lower back. The primary outcome measure was pain intensity at day 18. Secondary outcomes included functional disability, quality of life, fatigue and sleep quality as well as pressure pain sensitivity, satisfaction and safety at day 18 and 6 months. Altogether 141 patients were included in this study (139 females, 55.8 ± 9.1 years). After 18 days patients reported significant less pain after cupping compared to usual care (difference -12.4; 95% CI: -18.9; -5.9, p cupping and sham cupping; and only minor side effects were observed. Despite cupping therapy being more effective than usual care to improve pain intensity and quality of life, effects of cupping therapy were small and comparable to those of a sham treatment, and as such cupping cannot be recommended for fibromyalgia at the current time.

  19. COPA IN PANTANAL: perceptions of cuiabanos on World Cup Soccer 2014 Cuiabá / MT

    Directory of Open Access Journals (Sweden)

    Francisco Xavier Freire Rodrigues

    2012-09-01

    Full Text Available The theme of this work is the preparation for reception of the World Cup 2014 in Cuiabá/ MT. This is a study about the preparations for the Capital of Mato Grosso to stagematches of the World Cup Football 2014. The research objectives are: (a investigatethe process of preparing the city of Cuiabá / MT to hold World Cup matches in 2014and (b verify and analyze the perceptions of the population cuiabana about the benefitsof the mega event (World Cup . We use techniques such as: literature review, deskresearch, interviews, photographs, among, others.

  20. An experimental and computational investigation of the post-yield behaviour of trabecular bone during vertebral device subsidence.

    Science.gov (United States)

    Kelly, Nicola; Harrison, Noel M; McDonnell, Pat; McGarry, J Patrick

    2013-08-01

    Interbody fusion device subsidence has been reported clinically. An enhanced understanding of the mechanical behaviour of the surrounding bone would allow for accurate predictions of vertebral subsidence. The multiaxial inelastic behaviour of trabecular bone is investigated at a microscale and macroscale level. The post-yield behaviour of trabecular bone under hydrostatic and confined compression is investigated using microcomputed tomography-derived microstructural models, elucidating a mechanism of pressure-dependent yielding at the macroscopic level. Specifically, microstructural trabecular simulations predict a distinctive yield point in the apparent stress-strain curve under uniaxial, confined and hydrostatic compression. Such distinctive apparent stress-strain behaviour results from localised stress concentrations and material yielding in the trabecular microstructure. This phenomenon is shown to be independent of the plasticity formulation employed at a trabecular level. The distinctive response can be accurately captured by a continuum model using a crushable foam plasticity formulation in which pressure-dependent yielding occurs. Vertebral device subsidence experiments are also performed, providing measurements of the trabecular plastic zone. It is demonstrated that a pressure-dependent plasticity formulation must be used for continuum level macroscale models of trabecular bone in order to replicate the experimental observations, further supporting the microscale investigations. Using a crushable foam plasticity formulation in the simulation of vertebral subsidence, it is shown that the predicted subsidence force and plastic zone size correspond closely with the experimental measurements. In contrast, the use of von Mises, Drucker-Prager and Hill plasticity formulations for continuum trabecular bone models lead to over prediction of the subsidence force and plastic zone.

  1. Quantitative Evaluation of Trabecular Bone Structure by Calcaneus MR Images Texture Analysis of Healthy Volunteers and Osteoporotic Subjects

    Science.gov (United States)

    2001-10-25

    purpose is to set up a calcaneus architecture analysis by MRI that could be used routinely to improve fracture risk prediction and to assess anti...1 of 3 QUANTITATIVE EVALUATION OF TRABECULAR BONE STRUCTURE BY CALCANEUS MR IMAGES TEXTURE ANALYSIS OF HEALTHY VOLUNTEERS AND OSTEOPOROTIC...Picardie Jules Verne, Amiens, FRANCE Abstract - The aim of this study is to evaluate, in vivo, trabecular bone structure of the calcaneus of healthy

  2. Grizzly bears (Ursus arctos horribilis) and black bears (Ursus americanus) prevent trabecular bone loss during disuse (hibernation)

    OpenAIRE

    McGee-Lawrence, Meghan E.; Wojda, Samantha J.; Barlow, Lindsay N.; Drummer, Thomas D.; Castillo, Alesha B.; Kennedy, Oran; Condon, Keith W.; Auger, Janene; Black, Hal L.; Nelson, O. Lynne; Robbins, Charles T.; Donahue, Seth W.

    2009-01-01

    Disuse typically causes an imbalance in bone formation and bone resorption, leading to losses of cortical and trabecular bone. In contrast, bears maintain balanced intracortical remodeling and prevent cortical bone loss during disuse (hibernation). Trabecular bone, however, is more detrimentally affected than cortical bone in other animal models of disuse. Here we investigated the effects of hibernation on bone remodeling, architectural properties, and mineral density of grizzly bear (Ursus a...

  3. Bisphosphonate treatment affects trabecular bone apparent modulus through micro-architecture rather than matrix properties

    DEFF Research Database (Denmark)

    Ding, Ming

    2004-01-01

    and trabecular architecture independently. Conventional histomorphometry and microdamage data were obtained from the second and third lumbar vertebrae of the same dogs [Bone 28 (2001) 524]. Bisphosphonate treatment resulted in an increased apparent Young's modulus, decreased bone turnover, increased calcified...... matrix density, and increased microdamage. We could not detect any change in the effective Young's modulus of the calcified matrix in the bisphosphonate treated groups. The observed increase in apparent Young's modulus was due to increased bone mass and altered trabecular architecture rather than changes...... in the calcified matrix modulus. We hypothesize that the expected increase in the Young's modulus of the calcified matrix due to the increased calcified matrix density was counteracted by the accumulation of microdamage. Udgivelsesdato: 2004 May...

  4. Novel fixation method of a periprosthetic fracture of the acetabulum using burr holes through the retained cup for locking screw fixation

    Directory of Open Access Journals (Sweden)

    James A. Browne, MD

    2015-03-01

    Full Text Available The incidence of periprosthetic fractures of the acetabulum associated with a total hip arthroplasty is relatively low but may be increasing. Treatment options depend upon the stability of the prosthesis. In this case, we report an unusual fracture pattern where a large portion of posterior column remained osseointegrated to a displaced uncemented acetabular component and removal of the cup would have resulted in massive structural bone loss and potential pelvic discontinuity. A metal cutting burr was used to create additional screw holes in the cup to allow us to retain the original implant and also obtain fixation of the fracture. The patient had a good outcome at one year with a healed fracture, stable implant, and excellent function. To our knowledge, this technique has not been previously described and offers surgeons an approach to fix these challenging fractures.

  5. Trabecular bone structure parameters from 3D image processing of clinical multi-slice and cone-beam computed tomography data

    Energy Technology Data Exchange (ETDEWEB)

    Klintstroem, Eva; Smedby, Oerjan [Linkoeping University, Center for Medical Image Science and Visualization (CMIV), Linkoeping (Sweden); UHL County Council of Oestergoetland, Department of Radiology, Linkoeping (Sweden); Linkoeping University, Department of Medical and Health Sciences (IMH)/Radiology, Linkoeping (Sweden); Moreno, Rodrigo [Linkoeping University, Center for Medical Image Science and Visualization (CMIV), Linkoeping (Sweden); Linkoeping University, Department of Medical and Health Sciences (IMH)/Radiology, Linkoeping (Sweden); Brismar, Torkel B. [KUS Huddinge, Department of Clinical Science, Intervention and Technology at Karolinska Institutet and Department of Radiology, Stockholm (Sweden)

    2014-02-15

    Bone strength depends on both mineral content and bone structure. The aim of this in vitro study was to develop a method of quantitatively assessing trabecular bone structure by applying three-dimensional image processing to data acquired with multi-slice and cone-beam computed tomography using micro-computed tomography as a reference. Fifteen bone samples from the radius were examined. After segmentation, quantitative measures of bone volume, trabecular thickness, trabecular separation, trabecular number, trabecular nodes, and trabecular termini were obtained. The clinical machines overestimated bone volume and trabecular thickness and underestimated trabecular nodes and number, but cone-beam CT to a lesser extent. Parameters obtained from cone beam CT were strongly correlated with μCT, with correlation coefficients between 0.93 and 0.98 for all parameters except trabecular termini. The high correlation between cone-beam CT and micro-CT suggest the possibility of quantifying and monitoring changes of trabecular bone microarchitecture in vivo using cone beam CT. (orig.)

  6. Speech teams of wrestling at the European Nations Cup 2015

    Directory of Open Access Journals (Sweden)

    Pavel Panov

    2015-12-01

    Full Text Available Purpose: to analyze the performance of national teams of wrestling at the European Nations Cup in 2015. Material and Methods: the analysis of 208 wrestlers highly. Results: determined that, among other factors, the advantage of the strongest wrestlers is successful and stable use of technical and tactical actions during the fight and the ability to impose his opponent style of fighting. Conclusions: it was found that in the competitive technology dominated the offensive, the fight is ongoing at a fast pace, techniques are performed after prior training and if the athlete is confident that the reception will be executed

  7. A comparison and verification of computational methods to determine the permeability of vertebral trabecular bone.

    Science.gov (United States)

    Widmer, René P; Ferguson, Stephen J

    2013-06-01

    Fluid flow in the intertrabecular spaces of vertebral bone has been implicated in a number of physiological phenomena. Despite the potential clinical significance of the flow of various fluids through the intertrabecular cavities, the intrinsic permeability of trabecular bone is not fully characterized or understood. Furthermore, very little is known about the interdependence of permeability and morphological parameters. The main purpose of this study is to characterize computational methods to determine intrinsic bone permeability from three-dimensional computed tomography (CT) image stacks that were, depending on the underlying algorithm of each model, acquired at a spatial resolution ranging from the order of 500 μm (macroscale) up to 10 μm (microscale). A Finite Element formulation of the steady-state Stokes flow and an in house developed pore network modeling approach compute permeability on the microscopic length scale. To approximate the geometry of the trabecular bone network, a cellular model is used to map morphological information into intrinsic permeability by means of a log-linear regression equation. If the image resolution is too low for the quantification of the trabecular bone architecture, permeability is directly derived by fitting a simplified version of the log-linear regression equation to the CT Hounsfield values. Depending on the resolution of the raw image data and the chosen model, permeability value correlations are 0.31 ≤ R(2) ≤ 0.90 compared to the Finite Element method, that is referred to as the baseline for any comparisons in this study. Furthermore, we found no significant dependence of the intrinsic permeability on the trabecular thickness parameter.

  8. Calorie restriction aggravated cortical and trabecular bone architecture in ovariectomy-induced estrogen-deficient rats.

    Science.gov (United States)

    Ahn, Hyejin; Seo, Dong-Hyun; Kim, Han Sung; Choue, Ryowon

    2014-08-01

    We hypothesized that calorie restriction (CR) and estrogen deficiency (ovariectomy [OVX]) would aggravate bone biomarkers and structural parameters in rats. Seven-week-old female Sprague-Dawley rats were randomized to sham-operated groups and fed either an ad libitum diet (SHAM-AL) or a CR diet (SHAM-CR); ovariectomy-operated groups were fed an ad libitum diet (OVX-AL) or a CR diet (OVX-CR). For 8 weeks, the OVX-AL and SHAM-AL groups were fed the same diet, whereas CR groups were fed a diet containing 50% fewer calories. Bone-related biomarkers and structural parameters (OC; deoxypyridinoline [DPD]; N-terminal telopeptide, NTx; architecture and mineralization; and microcomputed tomography images) were analyzed at the end of the experiment. The serum OC levels of calorie-restricted groups (SHAM-CR and OVX-CR) were significantly lower than those of the AL groups (SHAM-AL and OVX-AL) (P calorie-restricted and ovariectomized groups were higher than those of their counterparts (P calorie-restricted groups were higher than those of AL groups (P calorie-restricted and ovariectomized groups had lower values of bone volume to total volume, trabecular number, and bone mineral density, but higher values of trabecular separation than those of their counterparts (P calorie-restricted groups had reduced values of bone volume, mean polar moment of inertia, and cortical thickness compared to the AL groups (P < .05). In conclusion, severe CR with or without OVX during the growth period in rats is equally detrimental to bone; CR has detrimental effects on trabecular and cortical bone; and estrogen deficiency only had an effect on trabecular bone. Copyright © 2014 Elsevier Inc. All rights reserved.

  9. Cortical and trabecular bone are equally affected in rats with renal failure and secondary hyperparathyroidism.

    Science.gov (United States)

    Bajwa, Nikita M; Sanchez, Cheryl P; Lindsey, Richard C; Watt, Heather; Mohan, Subburaman

    2018-02-02

    Changes in mineral metabolism and bone structure develop early in the course of chronic kidney disease and at end-stage are associated with increased risk of fragility fractures. The disruption of phosphorus homeostasis leads to secondary hyperparathyroidism, a common complication of chronic kidney disease. However, the molecular pathways by which high phosphorus influences bone metabolism in the early stages of the disease are not completely understood. We investigated the effects of a high phosphorus diet on bone and mineral metabolism using a 5/6 nephrectomy model of chronic kidney disease. Four-week old rats were randomly assigned into groups: 1) Control with standard diet, 2) Nephrectomy with standard rodent diet, and 3) Nephrectomy with high phosphorus diet. Rats underwent in vivo imaging at baseline, day 14, and day 28, followed by ex vivo imaging. Cortical bone density at the femoral mid-diaphysis was reduced in nephrectomy-control and nephrectomy-high phosphorus compared to control rats. In contrast, trabecular bone mass was reduced at both the lumbar vertebrae and the femoral secondary spongiosa in nephrectomy-high phosphorus but not in nephrectomy-control. Reduced trabecular bone volume adjusted for tissue volume was caused by changes in trabecular number and separation at day 35. Histomorphometry revealed increased bone resorption in tibial secondary spongiosa in nephrectomy-control. High phosphorus diet-induced changes in bone microstructure were accompanied by increased serum parathyroid hormone and fibroblast growth factor 23 levels. Our study demonstrates that changes in mineral metabolism and hormonal dysfunction contribute to trabecular and cortical bone changes in this model of early chronic kidney disease.

  10. Nanoindentation of Trabecular Bone - Comparison with Uniaxial Testing of Single Trabecula

    Czech Academy of Sciences Publication Activity Database

    Jiroušek, Ondřej; Němeček, J.; Kytýř, Daniel; Kunecký, Jiří; Zlámal, Petr; Doktor, Tomáš

    2011-01-01

    Roč. 105, č. 17 (2011), s. 668-671 ISSN 0009-2770 R&D Projects: GA ČR(CZ) GAP105/10/2305 Institutional research plan: CEZ:AV0Z20710524 Keywords : constitutive modelling * micromechanics * nanoindentation * trabecular bone Subject RIV: JJ - Other Materials Impact factor: 0.529, year: 2011 http://www.chemicke-listy.cz/common/content-issue_17-volume_105-year_2011.html

  11. Relationships between age and microarchitectural descriptors of iliac trabecular bone determined by microCT.

    Science.gov (United States)

    Deguette, C; Ramond-Roquin, A; Rougé-Maillart, C

    2017-06-01

    Estimation of age at death is a major issue in anthropology. The main anthropological histological methods propose studying the architecture of cortical bone. In bone histomorphometry, researches on metabolic bone diseases have provided normative tables for trabecular bone volume (BV/TV) according to age and gender of individuals on trans-iliac bone biopsies. We have used microCT, a non-destructive tool for measuring bone volume and trabecular descriptors to compare the French tables to a series of forensic anthropological population and if the two iliac bones could be used interchangeably. Coxal bone of a personal forensic collection whose age and gender were known (DNA identification) were used. Bone samples, centered on the same area than bone biopsy. MicroCT (pixel size: 36μm) was used to measure BV/TV and morphometric trabecular parameters of microarchitecture. An adjusted Z-score was calculated for BV/TV to compare with normative tables and a right/left comparison of trabecular parameters was provided. Twenty-seven iliac bones, which 20 forming 10 complete pelvises, aged between 24 and 73y.o. (average of 47.7 y.o.) were used. All adjusted Z-score were within normal values. There was a strong positive correlation between right and left sides for Tb.Th, Tb.N and Tb.Sp, but an insignificant correlation was obtained for BV/TV. Normative tables between age and BV/TV are valid and therefore usable in anthropology. They may represent an alternative to determine the age at death. Nevertheless, it requires a precise technique that could be a drawback in current practice. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  12. Strain analysis of trabecular bone using time-resolved X-ray microtomography

    Czech Academy of Sciences Publication Activity Database

    Jiroušek, Ondřej; Zlámal, Petr; Kytýř, Daniel; Kroupa, M.

    2011-01-01

    Roč. 633, Suppl. 1 (2011), s. 148-151 ISSN 0168-9002. [International Workshop on Radiation Imaging Detectors /11./. Praha, 28.06.2009-02.07.2009] R&D Projects: GA ČR(CZ) GP103/07/P483 Institutional research plan: CEZ:AV0Z20710524 Keywords : trabecular bone * X-ray microtomography * strain analysis * intrinsic material properties Subject RIV: JB - Sensors, Measurment, Regulation Impact factor: 1.207, year: 2011

  13. The three-dimensional microstructure of trabecular bone: Analysis of site-specific variation in the human jaw bone

    International Nuclear Information System (INIS)

    Kim, Jo Eun; Yi, Won Jin; Heo, Min Suk; Lee, Sam Sun; Choi, Soon Chul; Huh, Kyung Hoe; Shin, Jae Myung; Oh, Sung Ook

    2013-01-01

    This study was performed to analyze human maxillary and mandibular trabecular bone using the data acquired from micro-computed tomography (micro-CT), and to characterize the site-specific microstructures of trabeculae. Sixty-nine cylindrical bone specimens were prepared from the mandible and maxilla. They were divided into 5 groups by region: the anterior maxilla, posterior maxilla, anterior mandible, posterior mandible, and mandibular condyle. After the specimens were scanned using a micro-CT system, three-dimensional microstructural parameters such as the percent bone volume, bone specific surface, trabecular thickness, trabecular separation, trabecular number, structure model index, and degrees of anisotropy were analyzed. Among the regions other than the condylar area, the anterior mandibular region showed the highest trabecular thickness and the lowest value for the bone specific surface. On the other hand, the posterior maxilla region showed the lowest trabecular thickness and the highest value for the bone specific surface. The degree of anisotropy was lowest at the anterior mandible. The condyle showed thinner trabeculae with a more anisotropic arrangement than the other mandibular regions. There were microstructural differences between the regions of the maxilla and mandible. These results suggested that different mechanisms of external force might exist at each site.

  14. The three-dimensional microstructure of trabecular bone: Analysis of site-specific variation in the human jaw bone

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jo Eun; Yi, Won Jin; Heo, Min Suk; Lee, Sam Sun; Choi, Soon Chul; Huh, Kyung Hoe [Dept. of Oral and Maxillofacial Radiology and Dental Research Institute, School of Dentistry, Seoul National University, Seoul (Korea, Republic of); Shin, Jae Myung [Dept. of Oral and Maxillofacial Surgery, Ilsan Paik Hospital, Inje University College of Medicine, Goyang (Korea, Republic of); Oh, Sung Ook [A Plus Dental Clinic, Seoul (Korea, Republic of)

    2013-12-15

    This study was performed to analyze human maxillary and mandibular trabecular bone using the data acquired from micro-computed tomography (micro-CT), and to characterize the site-specific microstructures of trabeculae. Sixty-nine cylindrical bone specimens were prepared from the mandible and maxilla. They were divided into 5 groups by region: the anterior maxilla, posterior maxilla, anterior mandible, posterior mandible, and mandibular condyle. After the specimens were scanned using a micro-CT system, three-dimensional microstructural parameters such as the percent bone volume, bone specific surface, trabecular thickness, trabecular separation, trabecular number, structure model index, and degrees of anisotropy were analyzed. Among the regions other than the condylar area, the anterior mandibular region showed the highest trabecular thickness and the lowest value for the bone specific surface. On the other hand, the posterior maxilla region showed the lowest trabecular thickness and the highest value for the bone specific surface. The degree of anisotropy was lowest at the anterior mandible. The condyle showed thinner trabeculae with a more anisotropic arrangement than the other mandibular regions. There were microstructural differences between the regions of the maxilla and mandible. These results suggested that different mechanisms of external force might exist at each site.

  15. Trabecular bone microstructure and mineral density in human residual ridge at various intervals over a long period after tooth extraction.

    Science.gov (United States)

    Tanaka, Mikako; Yamashita-Mikami, Emi; Akazawa, Kohei; Yoshizawa, Michiko; Arai, Yoshiaki; Ejiri, Sadakazu

    2018-03-06

    Long-term changes of trabecular microstructure in human tooth extraction socket have not been investigated. To examine the trabecular microstructure of human residual ridges at various intervals following tooth extraction, and to determine whether bone remodeling activity can attain points of relative stability and when such points are reached. Forty-four bone biopsy specimens were obtained from lower molar or premolar regions of residual ridges. Postextraction times ranged from 1.6 to 360 months. Samples were analyzed using micro-computed tomography and three-dimensional bone morphometry with histological analyses. Trabecular bone parameters were plotted against postextraction times, and a stepwise piecewise linear regression analysis was performed to determine at which points of time these parameters either increased or decreased. Using piecewise linear regression, "inflection points" were found in most trabecular bone parameters between 7 and 12 months postextraction. Among the residual ridge samples, woven trabecular structure became mature, consisting of thick lamellar trabeculae with sufficient bone density, under dynamic bone remodeling until the 7th to 12th month post-tooth extraction. After this period, the mature network structure remained stable with low remodeling activity. Bone remodeling of trabecular structure in human residual ridge after tooth extraction had a stabilization period. © 2018 Wiley Periodicals, Inc.

  16. Assessing vertebral fracture risk on volumetric quantitative computed tomography by geometric characterization of trabecular bone structure

    Science.gov (United States)

    Checefsky, Walter A.; Abidin, Anas Z.; Nagarajan, Mahesh B.; Bauer, Jan S.; Baum, Thomas; Wismüller, Axel

    2016-03-01

    The current clinical standard for measuring Bone Mineral Density (BMD) is dual X-ray absorptiometry, however more recently BMD derived from volumetric quantitative computed tomography has been shown to demonstrate a high association with spinal fracture susceptibility. In this study, we propose a method of fracture risk assessment using structural properties of trabecular bone in spinal vertebrae. Experimental data was acquired via axial multi-detector CT (MDCT) from 12 spinal vertebrae specimens using a whole-body 256-row CT scanner with a dedicated calibration phantom. Common image processing methods were used to annotate the trabecular compartment in the vertebral slices creating a circular region of interest (ROI) that excluded cortical bone for each slice. The pixels inside the ROI were converted to values indicative of BMD. High dimensional geometrical features were derived using the scaling index method (SIM) at different radii and scaling factors (SF). The mean BMD values within the ROI were then extracted and used in conjunction with a support vector machine to predict the failure load of the specimens. Prediction performance was measured using the root-mean-square error (RMSE) metric and determined that SIM combined with mean BMD features (RMSE = 0.82 +/- 0.37) outperformed MDCT-measured mean BMD (RMSE = 1.11 +/- 0.33) (p < 10-4). These results demonstrate that biomechanical strength prediction in vertebrae can be significantly improved through the use of SIM-derived texture features from trabecular bone.

  17. An ontogenetic framework linking locomotion and trabecular bone architecture with applications for reconstructing hominin life history.

    Science.gov (United States)

    Raichlen, David A; Gordon, Adam D; Foster, Adam D; Webber, James T; Sukhdeo, Simone M; Scott, Robert S; Gosman, James H; Ryan, Timothy M

    2015-04-01

    The ontogeny of bipedal walking is considered uniquely challenging, due in part to the balance requirements of single limb support. Thus, locomotor development in humans and our bipedal ancestors may track developmental milestones including the maturation of the neuromuscular control system. Here, we examined the ontogeny of locomotor mechanics in children aged 1-8, and bone growth and development in an age-matched skeletal sample to identify bony markers of locomotor development. We show that step-to-step variation in mediolateral tibia angle relative to the vertical decreases with age, an indication that older children increase stability. Analyses of trabecular bone architecture in the distal tibia of an age-matched skeletal sample (the Norris Farms #36 archaeological skeletal collection) show a bony signal of this shift in locomotor stability. Using a grid of eleven cubic volumes of interest (VOI) in the distal metaphysis of each tibia, we show that the degree of anisotropy (DA) of trabecular struts changes with age. Intra-individual variation in DA across these VOIs is generally high at young ages, likely reflecting variation in loading due to kinematic instability. With increasing age, mean DA converges on higher values and becomes less variable across the distal tibia. We believe the ontogeny of distal tibia trabecular architecture reflects the development of locomotor stability in bipeds. We suggest this novel bony marker of development may be used to assess the relationship between locomotor development and other life history milestones in fossil hominins. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Effect of including damage at the tissue level in the nonlinear homogenisation of trabecular bone.

    Science.gov (United States)

    Levrero-Florencio, Francesc; Manda, Krishnagoud; Margetts, Lee; Pankaj, Pankaj

    2017-10-01

    Being able to predict bone fracture or implant stability needs a proper constitutive model of trabecular bone at the macroscale in multiaxial, non-monotonic loading modes. Its macroscopic damage behaviour has been investigated experimentally in the past, mostly with the restriction of uniaxial cyclic loading experiments for different samples, which does not allow for the investigation of several load cases in the same sample as damage in one direction may affect the behaviour in other directions. Homogenised finite element models of whole bones have the potential to assess complicated scenarios and thus improve clinical predictions. The aim of this study is to use a homogenisation-based multiscale procedure to upscale the damage behaviour of bone from an assumed solid phase constitutive law and investigate its multiaxial behaviour for the first time. Twelve cubic specimens were each submitted to nine proportional strain histories by using a parallel code developed in-house. Evolution of post-elastic properties for trabecular bone was assessed for a small range of macroscopic plastic strains in these nine load cases. Damage evolution was found to be non-isotropic, and both damage and hardening were found to depend on the loading mode (tensile, compression or shear); both were characterised by linear laws with relatively high coefficients of determination. It is expected that the knowledge of the macroscopic behaviour of trabecular bone gained in this study will help in creating more precise continuum FE models of whole bones that improve clinical predictions.

  19. Trabecular smooth muscle modulates the capacitor function of the penis. Studies on a rabbit model.

    Science.gov (United States)

    Saenz de Tejada, I; Moroukian, P; Tessier, J; Kim, J J; Goldstein, I; Frohrib, D

    1991-05-01

    We investigated the role of trabecular smooth muscle tone in regulation of intracavernosal pressure, venous outflow resistance, and penile capacitance. In an isolated rabbit whole penis model, corpora cavernosa were infused with either contracting (high K(+)-norepinephrine combination) or relaxing (no added Ca(2+)-papaverine combination) physiological salt solutions while intracavernosal pressure was recorded. An infusion pump regulated by an intracavernosal pressure feedback mechanism enabled the measurement of flow necessary to maintain intracavernosal pressures at 30, 60, 90, 120, and 150 mmHg under steady-state conditions (inflow = outflow). These experiments allowed resistance to outflow from corpora to be calculated when trabecular smooth muscle was either constricted or relaxed. Decay in intracavernosal pressure over time from various predetermined intracavernosal pressures (150, 120, 90, 60, and 30 mmHg) was studied under conditions of zero inflow following contraction or relaxation of trabecular smooth muscle. This permitted calculation of the time constant, which together with the outflow resistance, permitted the calculation of penile capacitance. When smooth muscle is relaxed, venous outflow resistance is high, constant, and independent of intracavernosal pressure. Furthermore, relaxation of smooth muscle allows expansion of corpora with accumulation of volume under pressure, enabling the penis to act as a capacitor. This capacitor function is limited in the presence of constant high outflow resistance by stiffness of the fibroelastic elements of penis, tunica, and fibroelastic frame, which exhibit nonlinear deflection trends. Analysis of these variables has led us to propose a model for penile erection.

  20. Artificial composite bone as a model of human trabecular bone: the implant-bone interface.

    Science.gov (United States)

    Grant, J A; Bishop, N E; Götzen, N; Sprecher, C; Honl, M; Morlock, M M

    2007-01-01

    The use of artificial bones in implant testing has become popular due to their low variability and ready availability. However, friction coefficients, which are critical to load transfer in uncemented implants, have rarely been compared between human and artificial bone, particularly for wet and dry conditions. In this study, the static and dynamic friction coefficients for four commercially used titanium surfaces (polished, Al(2)O(3) blasted, plasma sprayed, beaded) acting on the trabecular component of artificial bones (Sawbones) were compared to those for human trabecular bone. Artificial bones were tested in dry and wet conditions and normal interface stress was varied (0.25, 0.5, 1.0MPa). Friction coefficients were mostly lower for artificial bones than real bone. In particular, static friction coefficients for the dry polished surface were 20% of those for real bone and 42-61% for the dry beaded surface, with statistical significance (alphaartificial bone models for pre-clinical implant testing that rely on interface load transfer with trabecular bone for mechanical integrity can be particularly sensitive to surface finish and lubrication conditions.

  1. Validation of composite finite elements efficiently simulating elasticity of trabecular bone.

    Science.gov (United States)

    Schwen, Lars Ole; Wolfram, Uwe

    2014-01-01

    Patient-specific analyses of the mechanical properties of bones become increasingly important for the management of patients with osteoporosis. The potential of composite finite elements (CFEs), a novel FE technique, to assess the apparent stiffness of vertebral trabecular bone is investigated in this study. Segmented volumes of cylindrical specimens of trabecular bone are compared to measured volumes. Elasticity under uniaxial loading conditions is simulated; apparent stiffnesses are compared to experimentally determined values. Computational efficiency is assessed and recommendations for simulation parameters are given. Validating apparent uniaxial stiffnesses results in concordance correlation coefficients 0.69 ≤ r(c) ≤ 0.92 for resolutions finer than 168 μm, and an average error of 5.8% between experimental and numerical results at 24 μm resolution. As an application, the code was used to compute local, macroscopic stiffness tensors for the trabecular structure of a lumbar vertebra. The presented technique allows for computing stiffness using smooth FE meshes at resolutions that are well achievable in peripheral high resolution quantitative CT. Therefore, CFEs could be a valuable tool for the patient-specific assessment of bone stiffness.

  2. Bone dosimetry using synthetic images to represent trabecular bones of five regions of the human body

    Energy Technology Data Exchange (ETDEWEB)

    Lima Filho, Jose de M. [Instituto Federal de Educacao, Ciencia e Tecnologia de Pernambuco (IFPE), Recife, PE (Brazil); Vieira, Jose W. [Escola Politecnica de Pernambuco (POLI). Universidade de Pernambuco (UPE), Recife, PE (Brazil); Lima, Vanildo J. de M., E-mail: vjr@ufpe.br [Departamento de Anatomia. Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil); Lima, Lindeval F., E-mail: lindeval@dmat.ufrr.br [Departamento de Matematica (DMAT). Universidade Federal de Roraima (UFRR), Boa Vista, RR (Brazil); Lima, Fernando R.A., E-mail: falima@cnen.gov.br [Centro Regional de Ciencias Nucleares (CRCN/NE-CNEN-PE), Recife, PE (Brazil); Vasconcelos, Wagner E. de [Departamento de Energia Nuclear (DEN). Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil)

    2011-07-01

    One of the greatest challenges in numerical dosimetry of ionizing radiation is to estimate the absorbed dose by bone tissue in the human body. The bone tissues of greater radiosensitivity are the red bone marrow (RBM), that consist of the hematopoietic cells, located within the trabecular bones, and the bone surface cells (BSC), called osteogenic cells. The report 70 of the ICRP lists five spongiosa regions with their respective volume percent of trabecular bone: ribs (also contemplating the clavicles and sternum), spine, long bones, pelvis and skull (also contemplating mandible). The Grupo de Pesquisa em Dosimetria Numerica (GDN/CNPq) has been built exposure computational models (ECMs) based on voxel phantoms and EGSnrc Monte Carlo code. To estimate the energy deposited in the RBM and in the BSC of a phantom, the GDN/CNPq has used a method based on micro-CT images of the five trabecular regions mentioned above. These images were provided by other research institutes and were obtained from scan of bone samples of adult. Here is the greatest difficulty in reproducing this method: besides the need for bone images of real people with micrometer resolution, the distribution of bone marrow in the human body, according to ICRP 70, varies with age. This article presents some proposals of the GDN/CNPQ for replacing in the ECMs the micro-CT images by images synthesized by the computer, based on Monte Carlo sampling. (author)

  3. Poor Acetabular Component Orientation Increases Revision Risk in Metal-on-Metal Hip Arthroplasty.

    Science.gov (United States)

    Tauriainen, Tuomas J T; Niinimäki, Tuukka T; Niinimäki, Jaakko L; Nousiainen, Tomi O P; Leppilahti, Juhana I

    2017-07-01

    The rate of and the reasons for the failure of metal-on-metal (MoM) bearings have recently been discussed in literature. The aim of this study was to evaluate the influence of acetabular cup inclination and version angles on revision risk in patients with MoM hip arthroplasty. We retrospectively reviewed 825 patients (976 hips) who underwent a MoM hip arthroplasty between 2000 and 2013. There were 474 men and 351 women, with a mean age of 58 (19-86) years. Acceptable cup orientation was considered to be inside the Lewinnek's safe zone. The mean acetabular inclination angle was 48.9° (standard deviation, 8.1°; range, 16°-76°) and version angle 20.6° (standard deviation, 9.9°; range, -25 to 46°). The cup was found to be outside the Lewinnek's safe zone in 571 hips (58.5%). Acetabular cup revision surgery was performed in 157 hips (16.1%). The cup angles were outside Lewinnek's safe zone in 69.2% of the revised hips. The mean interobserver reliability and intraobserver repeatability of the measurements of cup inclination and version angles were excellent (intraclass correlation coefficients >0.90). The odds ratio for revision in hips outside vs inside the Lewinnek's safe zone was 1.82 (95% confidence interval, 1.26-2.62; P = .0014). Our findings provide compelling evidence that a cup position outside the Lewinnek's safe zone is associated with increased revision risk in patients with MoM arthroplasty. Copyright © 2017. Published by Elsevier Inc.

  4. Clinical research evidence of cupping therapy in China: a systematic literature review

    Directory of Open Access Journals (Sweden)

    Wang Qian

    2010-11-01

    Full Text Available Abstract Background Though cupping therapy has been used in China for thousands of years, there has been no systematic summary of clinical research on it. This review is to evaluate the therapeutic effect of cupping therapy using evidence-based approach based on all available clinical studies. Methods We included all clinical studies on cupping therapy for all kinds of diseases. We searched six electronic databases, all searches ended in December 2008. We extracted data on the type of cupping and type of diseases treated. Results 550 clinical studies were identified published between 1959 and 2008, including 73 randomized controlled trials (RCTs, 22 clinical controlled trials, 373 case series, and 82 case reports. Number of RCTs obviously increased during past decades, but the quality of the RCTs was generally poor according to the risk of bias of the Cochrane standard for important outcome within each trials. The diseases in which cupping was commonly employed included pain conditions, herpes zoster, cough or asthma, etc. Wet cupping was used in majority studies, followed by retained cupping, moving cupping, medicinal cupping, etc. 38 studies used combination of two types of cupping therapies. No serious adverse effects were reported in the studies. Conclusions According to the above results, quality and quantity of RCTs on cupping therapy appears to be improved during the past 50 years in China, and majority of studies show potential benefit on pain conditions, herpes zoster and other diseases. However, further rigorous designed trials in relevant conditions are warranted to support their use in practice.

  5. A level set method for cupping artifact correction in cone-beam CT

    Energy Technology Data Exchange (ETDEWEB)

    Xie, Shipeng; Li, Haibo; Ge, Qi [College of Telecommunications and Information Engineering, Nanjing University of Posts and Telecommunications, Nanjing, Jiangsu 210003 (China); Li, Chunming, E-mail: li-chunming@hotmail.com [School of Electronic Engineering, University of Electronic Science and Technology of China (UESTC), Chengdu, Sichuan 611731 (China)

    2015-08-15

    Purpose: To reduce cupping artifacts and improve the contrast-to-noise ratio in cone-beam computed tomography (CBCT). Methods: A level set method is proposed to reduce cupping artifacts in the reconstructed image of CBCT. The authors derive a local intensity clustering property of the CBCT image and define a local clustering criterion function of the image intensities in a neighborhood of each point. This criterion function defines an energy in terms of the level set functions, which represent a segmentation result and the cupping artifacts. The cupping artifacts are estimated as a result of minimizing this energy. Results: The cupping artifacts in CBCT are reduced by an average of 90%. The results indicate that the level set-based algorithm is practical and effective for reducing the cupping artifacts and preserving the quality of the reconstructed image. Conclusions: The proposed method focuses on the reconstructed image without requiring any additional physical equipment, is easily implemented, and provides cupping correction through a single-scan acquisition. The experimental results demonstrate that the proposed method successfully reduces the cupping artifacts.

  6. Facility arrangements, food safety, and the environmental performance of disposable and reusable cups

    NARCIS (Netherlands)

    Potting, J.; Harst, van der E.J.M.

    2014-01-01

    Conventional disposable cups, made of fossil-based plastic or paper with inner lining of fossil-based plastic, are typically associated with an unnecessary use of scarce resources and a superfluous production of waste. An alternative has become available in disposable cups from bio-based and

  7. 78 FR 21260 - Safety Zone; Lubbers Cup Regatta; Spring Lake, MI

    Science.gov (United States)

    2013-04-10

    ... SECURITY Coast Guard 33 CFR PART 165 RIN 1625-AA00 Safety Zone; Lubbers Cup Regatta; Spring Lake, MI AGENCY... safety zone on Spring Lake in Spring Lake, Michigan. This safety zone is intended to restrict vessels from a portion of Spring Lake due to the Lubbers Cup Regatta. This temporary safety zone is necessary...

  8. Socio-economic impacts of the 2010 FIFA World Cup | Hermann ...

    African Journals Online (AJOL)

    Socio-economic impacts of the 2010 FIFA World Cup. ... Literature on the impacts of mega events on tourism is available but limited in number in terms of the impacts of mega events on local residents. This study analyses the post ... Keywords: Mega events, economic impacts, social impacts, World Cup, local community.

  9. Does surface roughness influence the primary stability of acetabular cups? A numerical and experimental biomechanical evaluation.

    Science.gov (United States)

    Le Cann, Sophie; Galland, Alexandre; Rosa, Benoît; Le Corroller, Thomas; Pithioux, Martine; Argenson, Jean-Noël; Chabrand, Patrick; Parratte, Sébastien

    2014-09-01

    Most acetabular cups implanted today are press-fit impacted cementless. Anchorage begins with the primary stability given by insertion of a slightly oversized cup. This primary stability is key to obtaining bone ingrowth and secondary stability. We tested the hypothesis that primary stability of the cup is related to surface roughness of the implant, using both an experimental and a numerical models to analyze how three levels of surface roughness (micro, macro and combined) affect the primary stability of the cup. We also investigated the effect of differences in diameter between the cup and its substrate, and of insertion force, on the cups' primary stability. The results of our study show that primary stability depends on the surface roughness of the cup. The presence of macro-roughness on the peripheral ring is found to decrease primary stability; there was excessive abrasion of the substrate, damaging it and leading to poor primary stability. Numerical modeling indicates that oversizing the cup compared to its substrate has an impact on primary stability, as has insertion force. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

  10. Effects of wet-cupping on blood pressure in hypertensive patients: a randomized controlled trial.

    Science.gov (United States)

    Aleyeidi, Nouran A; Aseri, Khaled S; Matbouli, Shadia M; Sulaiamani, Albaraa A; Kobeisy, Sumayyah A

    2015-11-01

    Although cupping remains a popular treatment modality worldwide, its efficacy for most diseases, including hypertension, has not been scientifically evaluated. We aimed to determine the efficacy of wet-cupping for high blood pressure, and the incidence of the procedure's side effects in the intervention group. This is a randomized controlled trial conducted in the General Practice Department at King Abdulaziz University Hospital, Jeddah, Saudi Arabia, between May 2013 and February 2014. There were two groups (40 participants each): intervention group undergoing wet-cupping (hijama) in addition to conventional hypertension treatment, and a control group undergoing only conventional hypertension treatment. Three wet-cupping sessions were performed every other day. The mean systolic and diastolic blood pressures were measured using a validated automatic sphygmomanometer. The follow-up period was 8 weeks. Wet-cupping provided an immediate reduction of systolic blood pressure. After 4 weeks of follow-up, the mean systolic blood pressure in the intervention group was 8.4 mmHg less than in the control group (P=0.046). After 8 weeks, there were no significant differences in blood pressures between the intervention and control groups. In this study, wet-cupping did not result in any serious side effects. Wet-cupping therapy is effective for reducing systolic blood pressure in hypertensive patients for up to 4 weeks, without serious side effects. Wet-cupping should be considered as a complementary hypertension treatment, and further studies are needed. ClinicalTrials.gov Identifier NCT01987583.

  11. [Clinical observation of post-herpetic neuralgia treated with TCM herbal cupping therapy].

    Science.gov (United States)

    Wu, Xi; Hu, Hui; Guo, Liang; Wang, Hui

    2013-02-01

    To compare the difference in the efficacy on post-herpetic neuralgia among TCM herbal cupping therapy, Chinese medicine thermal compressing therapy and mecobalamine. Fifty-seven cases were randomized into a TCM herbal cupping group, a thermal compressing group and a western medicine group, 19 cases in each one. The oral administration of ibuprofen was applied in every group. In the herbal cupping group, the bamboo cups soaked in the boiled Chinese herbal decoction were sucked on the most significant painful area. In the thermal compressing group, the towel soaked in the boiled Chinese herbal decoction was compressed on the most significant painful area. In the medication group, the muscular injection of mecobalamine was adopted. The treatment was given once a day, for 2 weeks totally in each group. SF-MPQ score and clinical efficacy before and after treatment were observed in each group. The remarkable effective rates were 78.9% (15/19), 36.8% (7/19) and 5.3% (1/19) in the TCM herbal cupping group, thermal compressing group and western medicine group separately. The efficacy in the TCM herbal cupping group was significantly superior to the thermal compressing group and western medicine group (all P cupping group was reduced more significantly as compared with the thermal compressing group and western medicine group (all P cupping therapy achieves the superior efficacy for post-herpetic neuralgia and relieves pain effectively of the patients, which is more advantageous than CM herbal thermal compressing therapy and Mecobalamine.

  12. Comparison of arboreal beetle catches in wet and dry collection cups with lindgren multiple funnel traps

    Science.gov (United States)

    Daniel R. Miller; Donald A. Duerr

    2008-01-01

    We compared the effectiveness of a dry collection cup (with an insecticide killing strip) to a wet collection cup (containing antifreeze) for use with Lindgren multiple-funnel traps in catching several common species of bark and wood-boring beetles, and their associates in southern pine forests. All traps were baited with either the binary combination of ethanol and...

  13. Facility arrangements and the environmental performance of disposable and reusable cups

    NARCIS (Netherlands)

    Potting, José; Harst-Wintraecken, van der Eugenie

    2015-01-01

    Purpose: This paper integrates two complementary life cycle assessment (LCA) studies with the aim to advice facility managers on the sustainable use of cups, either disposable or reusable. Study 1 compares three disposable cups, i.e., made from fossil-based polystyrene (PS), biobased and

  14. Analysis of patient load data from the 2003 Cricket World Cup in ...

    African Journals Online (AJOL)

    the patient presentation data for spectators attending the opening ceremony and all the 2003 Cricket World Cup matches played in South Africa in order to provide organ- isers with the basis of a sound medical care plan for mass gatherings of a similar nature. Methods. During the 2003 Cricket World Cup, data were.

  15. Athletic Departments' Operating Expenses as a Predictor of Their Directors' Cup Standing

    Science.gov (United States)

    Magner, Amber

    2014-01-01

    The NACDA Directors' Cup is a competition utilizing an unbiased scoring system that encourages a broad based athletic department as the standard for defining intercollegiate athletic success. Therefore, for NCAA DI athletic administrators the Directors' Cup should be the standard for defining intercollegiate athletic success. The purpose of this…

  16. 77 FR 75187 - Certain Food Containers, Cups, Plates, Cutlery, and Related Items and Packaging Thereof...

    Science.gov (United States)

    2012-12-19

    ... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-835] Certain Food Containers, Cups, Plates, Cutlery, and Related Items and Packaging Thereof; Commission Determination Not To Review an... containers, cups, plates, cutlery, and related items and packaging thereof by reason of infringement of U.S...

  17. 78 FR 37712 - Safety Zone; Chicago Match Cup Race; Lake Michigan; Chicago, IL

    Science.gov (United States)

    2013-06-24

    ... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 165 [Docket No. USCG-2013-0020] Safety Zone; Chicago Match Cup Race; Lake Michigan; Chicago, IL AGENCY: Coast Guard, DHS. ACTION: Notice of..., Illinois for the 2013 AWMRT Chicago Match Cup Race. This zone will be enforced from 8 a.m. until 8 p.m. on...

  18. 33 CFR 100.916 - Chris Craft Silver Cup Races, Algonac, MI.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Chris Craft Silver Cup Races, Algonac, MI. 100.916 Section 100.916 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY REGATTAS AND MARINE PARADES SAFETY OF LIFE ON NAVIGABLE WATERS § 100.916 Chris Craft Silver Cup...

  19. 77 FR 73311 - Special Local Regulation and Safety Zone; America's Cup Sailing Events, San Francisco, CA...

    Science.gov (United States)

    2012-12-10

    ... published a temporary final rule regulating the on-water activities associated with the ``Louis Vuitton Cup... a transit zone created to facilitate the safe transit of vessels needing access to pier space and... operational intentions of the Coast Guard and the America's Cup regulated areas. To ensure that members of the...

  20. Application of Faraday cup array detector in measurement of electron-beam distribution homogeneity

    International Nuclear Information System (INIS)

    Xu Zhiguo; Wang Jinchuan; Xiao Guoqing; Guo Zhongyan; Wu Lijie; Mao Ruishi; Zhang Li

    2005-01-01

    It is described that a kind of Faraday cup array detector, which consists of Faraday cup, suppressor electrode insulation PCB board, Base etc. The homogeneity of electron-beam distribution is measured and the absorbed dose for the irradiated sample is calculated. The results above provide the important parameters for the irradiation experiment and the improvement for the quality of electron beam. (authors)

  1. Faraday cup with nanosecond response and adjustable impedance for fast electron beam characterization

    International Nuclear Information System (INIS)

    Hu Jing; Rovey, Joshua L.

    2011-01-01

    A movable Faraday cup design with simple structure and adjustable impedance is described in this work. This Faraday cup has external adjustable shunt resistance for self-biased measurement setup and 50 Ω characteristic impedance to match with 50 Ω standard BNC coaxial cable and vacuum feedthroughs for nanosecond-level pulse signal measurements. Adjustable shunt resistance allows self-biased measurements to be quickly acquired to determine the electron energy distribution function. The performance of the Faraday cup is validated by tests of response time and amplitude of output signal. When compared with a reference source, the percent difference of the Faraday cup signal fall time is less than 10% for fall times greater than 10 ns. The percent difference of the Faraday cup signal pulse width is below 6.7% for pulse widths greater than 10 ns. A pseudospark-generated electron beam is used to compare the amplitude of the Faraday cup signal with a calibrated F-70 commercial current transformer. The error of the Faraday cup output amplitude is below 10% for the 4-14 kV tested pseudospark voltages. The main benefit of this Faraday cup is demonstrated by adjusting the external shunt resistance and performing the self-biased method for obtaining the electron energy distribution function. Results from a 4 kV pseudospark discharge indicate a ''double-humped'' energy distribution.

  2. Intra- and inter-observer agreement and reliability of bone mineral density measurements around acetabular cup

    DEFF Research Database (Denmark)

    Mussmann, Bo Redder; Overgaard, Soren; Torfing, Trine

    2017-01-01

    with single-energy CT (SECT) and DECT in cemented and cementless cups.Material and Methods: Twenty-four acetabular cups inserted in porcine hip specimens were scanned with SECT and DECT. Bone density was measured in a three-dimensional volume adjacent to the cup. Double measurements were performed.......Results: BMD derived from SECT was approximately four times higher than that of DECT. In both scan modes, intraclass correlation coefficient (ICC) was >0.90 with no differences between repeated measurements, except for uncemented cups where a statistically significant difference of 11 mg/cm3 was found...... with DECT. DECT showed narrower limits of agreement than SECT. Inter-observer analysis showed small differences.Conclusion: BMD can be estimated with high intra- and inter-observer reliability with SECT and DECT around acetabular cups using custom software. The intra- and inter-observer agreement of DECT...

  3. [Clinical application of moving cupping therapy based on skin reaction observation and syndrome differentiation].

    Science.gov (United States)

    Deng, Xiao-Lan; Chen, Bo; Chen, Ze-Lin

    2014-12-01

    The diagnostic evidence on clinical diseases and theoretic basis of moving cupping therapy were ex- plored in the paper. By the observation of the local reaction, such as skin appearance and color, the affected location, duration of sickness and nature of disease were judged. Different moving cupping methods were selected for different disorders. It was discovered that the property of syndromes should be recognized by the palpation on skin and muscle in the moving cupping therapy so that the pathogenesis and treating principle could be carefully determined. The moving cupping therapy is the important component of body surface therapy. Skin reaction observation and syndrome differentiation is the essential guidance of the moving cupping therapy.

  4. Three-dimensional trabecular bone architecture of the lumbar spine in bone metastasis from prostate cancer: comparison with degenerative sclerosis

    International Nuclear Information System (INIS)

    Tamada, Tsutomu; Sone, Teruki; Imai, Shigeki; Kajihara, Yasumasa; Fukunaga, Masao; Jo, Yoshimasa

    2005-01-01

    Prostate cancer frequently metastasizes to bone, inducing osteosclerotic lesions. The objective of this study was to clarify the three-dimensional (3D) trabecular bone microstructure in bone metastasis from prostate cancer by comparison with normal and degenerative sclerotic bone lesions, using microcomputed tomography (micro-CT). A total of 32 cancellous bone samples were excised from the lumbar spine of six autopsy patients: 15 metastatic samples (one patient), eight degenerative sclerotic samples (four patients) and the rest from normal sites (three patients). The samples were serially scanned cross-sectionally by micro-CT with a pixel size of 23.20 μm, slice thickness of 18.56 μm, and image matrix of 512 x 512. Each image data set consisted of 250 consecutive slices. The volumes of interest (96 x 96 x 120 voxels) were defined in the original image sets and 3D indices of the trabecular microstructure were determined. The trabecular thickness (Tb.Th) in degenerative sclerotic lesions was significantly higher than that in normal sites, whereas no significant difference was observed in trabecular number (Tb.N). By contrast, in metastatic lesions, the Tb.N was significantly higher with increased bone volume fraction (BV/TV) than in normal sites, and no significant difference was found in Tb.Th. The characteristics of the trabecular surface in the metastatic samples showed concave structural elements with an increase in BV/TV, indicating osteolysis of the trabecular bone. In 3D reconstructed images, increased trabecular bone with an irregular surface was observed in samples from metastatic sites, which were uniformly sclerotic on soft X-ray radiographs. These results support, through 3D morphological features, the strong bone resorption effect in bone metastasis from prostate cancer. (orig.)

  5. Micro-finite-element method to assess elastic properties of trabecular bone at micro- and macroscopic level.

    Science.gov (United States)

    Rieger, R; Auregan, J C; Hoc, T

    2018-03-01

    The objective of the present study is to assess the mechanical behavior of trabecular bone based on microCT imaging and micro-finite-element analysis. In this way two methods are detailed: (i) direct determination of macroscopic elastic property of trabecular bone; (ii) inverse approach to assess mechanical properties of trabecular bone tissue. Thirty-five females and seven males (forty-two subjects) mean aged (±SD) 80±11.7 years from hospitals of Assistance publique-Hôpitaux de Paris (AP-HP) diagnosed with osteoporosis following a femoral neck fracture due to a fall from standing were included in this study. Fractured heads were collected during hip replacement surgery. Standardized bone cores were removed from the femoral head's equator by a trephine in a water bath. MicroCT images acquisition and analysis were performed with CTan ® software and bone volume fraction was then determined. Micro-finite-element simulations were per-formed using Abaqus 6.9-2 ® software in order to determine the macroscopic mechanical behaviour of the trabecular bone. After microCT acquisition, a longitudinal compression test was performed and the experimental macroscopic Young's Modulus was extracted. An inverse approach based on the whole trabecular bone's mechanical response and micro-finite-element analysis was performed to determine microscopic mechanical properties of trabecular bone. In the present study, elasticity of the tissue was shown to be similar to that of healthy tissue but with a lower yield stress. Classical histomorphometric analysis form microCT imaging associated with an inverse micro-finite-element method allowed to assess microscopic mechanical trabecular bone parameters. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  6. The pvc operon regulates the expression of the Pseudomonas aeruginosa fimbrial chaperone/usher pathway (cup) genes.

    Science.gov (United States)

    Qaisar, Uzma; Luo, Liming; Haley, Cecily L; Brady, Sean F; Carty, Nancy L; Colmer-Hamood, Jane A; Hamood, Abdul N

    2013-01-01

    The Pseudomonas aeruginosa fimbrial structures encoded by the cup gene clusters (cupB and cupC) contribute to its attachment to abiotic surfaces and biofilm formation. The P. aeruginosa pvcABCD gene cluster encodes enzymes that synthesize a novel isonitrile functionalized cumarin, paerucumarin. Paerucumarin has already been characterized chemically, but this is the first report elucidating its role in bacterial biology. We examined the relationship between the pvc operon and the cup gene clusters in the P. aeruginosa strain MPAO1. Mutations within the pvc genes compromised biofilm development and significantly reduced the expression of cupB1-6 and cupC1-3, as well as different genes of the cupB/cupC two-component regulatory systems, roc1/roc2. Adjacent to pvc is the transcriptional regulator ptxR. A ptxR mutation in MPAO1 significantly reduced the expression of the pvc genes, the cupB/cupC genes, and the roc1/roc2 genes. Overexpression of the intact chromosomally-encoded pvc operon by a ptxR plasmid significantly enhanced cupB2, cupC2, rocS1, and rocS2 expression and biofilm development. Exogenously added paerucumarin significantly increased the expression of cupB2, cupC2, rocS1 and rocS2 in the pvcA mutant. Our results suggest that pvc influences P. aeruginosa biofilm development through the cup gene clusters in a pathway that involves paerucumarin, PtxR, and different cup regulators.

  7. Anaemia and skin pigmentation after excessive cupping therapy by an unqualified therapist in Korea: a case report.

    Science.gov (United States)

    Kim, Kun Hyung; Kim, Tae-Hun; Hwangbo, Min; Yang, Gi Young

    2012-09-01

    A case is reported of skin pigmentation and associated anemia resulting from persistently repeated cupping therapies performed by an unqualified practitioner in South Korea. Almost 30 sessions of excessive cupping therapies with blood loss over two months yielded little benefit but led the patient to admit a hospital and receive blood transfusion for acquired iron deficiency anemia. Skin pigmentation on the cupping-attached region remained without any subjective discomfort. We suggest the importance of qualified health professionals when receiving cupping treatments.

  8. Do jumbo cups cause hip center elevation in revision THA? A computer simulation.

    Science.gov (United States)

    Nwankwo, Chima; Dong, Nick N; Heffernan, Christopher D; Ries, Michael D

    2014-02-01

    Acetabular revision THA with use of a large (jumbo) cup is an effective treatment for many cavitary and segmental peripheral bone defects. However, the jumbo cup may result in elevation of the hip center and protrusion through the anterior acetabular wall as a result of the oversized geometry of the jumbo cup compared with the physiologic acetabulum. The purpose of this computer simulation was to determine how much elevation of the hip center and anterior wall protrusion occurs in revision THA with use of a jumbo cup technique in which the inferior edge of the jumbo cup is placed at the inferior acetabular rim and the superior edge of the jumbo cup is placed against host bone at the superior margin of a posterosuperior bone defect. Two hundred sixty-five pelvic CT scans were analyzed by custom CT analytical software. The computer simulated oversized reaming. The vertical and anterior reamer center shifts were measured, and anterior column bone removal was determined. The computer simulation demonstrated that the hip center shifted 0.27 mm superiorly and 0.02 mm anteriorly, and anterior column bone removal increased 0.86 mm for every 1-mm increase in reamer diameter. Our results indicate that the jumbo cup technique results in hip center elevation despite placement of the cup adjacent to the inferior acetabulum. For a hypothetical increase from a 54-mm socket to a 72-mm socket, as one might see in the context of the revision of a failed THA, our model would predict an elevation of the hip center of approximately 5 mm and loss of approximately 15 mm of anterior column bone. This suggests that an increase in femoral head length may be needed to compensate for the hip center elevation caused by the use of a large jumbo cup in revision THA. A jumbo cup may also result in protrusion through the anterior wall.

  9. Radiotherapeutic concepts in cancer of unknown primary site; Strahlentherapeutische Konzepte beim CUP-Syndrom

    Energy Technology Data Exchange (ETDEWEB)

    Krug, D.; Debus, J.; Sterzing, F. [Universitaetsklinikum Heidelberg, Klinik fuer Radioonkologie und Strahlentherapie, Heidelberg (Germany)

    2014-02-15

    The term cancer of unknown primary (CUP) encompasses a group of entities which differ to a great extent regarding etiology, prognosis and therapeutic management. The aim of the study was an elaboration of the role of radiotherapy in CUP syndrome. Systematic literature search and specification of the available treatment options. Radiotherapy is an integral part of interdisciplinary management approaches for patients with CUP in both curative and palliative situations. Radio-oncological techniques, such as intensity-modulated radiotherapy and stereotactic body radiotherapy increase the therapeutic window. Modern diagnostic modalities from radiology and nuclear medicine are the cornerstone of radiotherapeutic interventions, especially in terms of target volume definition and pretherapeutic staging. In the interdisciplinary setting radiation oncology offers the possibility of curative and often organ preserving approaches in patients with axillary and cervical CUP. In addition, improvement and preservation of quality of life can be achieved in patients with metastatic disease. Radiation oncology is a crucial component of the interdisciplinary management of patients with CUP. Therapeutic decisions in patients with CUP should be made in an interdisciplinary setting. (orig.) [German] Das Cancer-of-unknown-primary(CUP)-Syndrom fasst eine Gruppe von Erkrankungen zusammen, die durch eine ausgepraegte Heterogenitaet hinsichtlich Aetiologie, Therapie und Prognose gepraegt sind. Darstellung der Rolle der Strahlentherapie beim CUP-Syndrom. Systematische Literaturrecherche und Erlaeuterung der Behandlungsoptionen. Die Strahlentherapie ist beim CUP-Syndrom sowohl in adjuvanten und definitiven Therapiekonzepten wie auch in palliativer Intention etabliert. Technisch innovative Verfahren wie die intensitaetsmodulierte Radiotherapie und die stereotaktische Bestrahlung im Koerperstammbereich ermoeglichen eine Vergroesserung der therapeutischen Breite. Eine leistungsfaehige und moderne

  10. Single- and dual energy QCT around acetabular cups in total hip arthroplasty using 3-dimensional segmentation

    DEFF Research Database (Denmark)

    Mussmann, Bo Redder; Andersen, Poul Erik; Torfing, Trine

    Background: Bone density measurements around hip implants are challenged by artifacts and the complex anatomy of the acetabulum. We developed 3D segmentation software and used dual energy CT to reduce artifacts. Purpose / Aim of Study: To test the between-scan agreement and reliability of segment......Background: Bone density measurements around hip implants are challenged by artifacts and the complex anatomy of the acetabulum. We developed 3D segmentation software and used dual energy CT to reduce artifacts. Purpose / Aim of Study: To test the between-scan agreement and reliability...... the cemented cup the mean BMD for SECT was 523 mg/ccm with a between-scan difference of 14 mg/ccm, p=0.25 and 186 mg/ccm in DECT with a difference of 6 mg/ccm, p=0.15. ICC was >0.95 with more narrow limits of agreement in DECT compared with SECT. Computed tomography dose index (CTDI) was 25% higher with DECT...... be beneficial in estimating BMD adjacent to metal implants, but radiation dose and image quality should be taken into consideration. BMD cannot be measured interchangeably with SECT and DECT....

  11. Mortar modified with sulfonated polystyrene produced from waste plastic cups

    Directory of Open Access Journals (Sweden)

    L. A. C. MOTTA

    Full Text Available Abstract In this work, we studied the addition of sulfonated polystyrene produced from waste plastic cups as an admixture for mortars. Mortars were analyzed with polystyrene content of 0.0; 0.2; 0.6; 1.0 and 1.4% in relation to the cement mass. The influence of polystyrene on the mortars' properties was evaluated by the consistency index, water retention, water absorption, porosity, elasticity modulus, compressive strength, flexural strength, bond tensile strength and microscopy. The increase in the sulfonated polystyrene content decreased the elasticity modulus of the mortar and, despite higher porosity, there was a reduction of water absorption by capillarity. In relation to mortar without admixture, the modified mortar showed an increase in water retention and consistency index, and a large increase in flexural strength and bond tensile strength. The significant increase of bond tensile strength (214% with admixture 1% highlights the potential of the produced material as an adhesive mortar.

  12. Media value of the Basketball World Cup 2006

    Directory of Open Access Journals (Sweden)

    Pedro Garcia-del-Barrio

    2007-10-01

    Full Text Available The number of businesses whose activities are based on immaterial assets is growing very rapidly, which demands new ways of evaluating the economic relevance of intangible assets. The aim of this study is precisely to examine the Basketball World Cup 2006 -a particular experience within the industry of spectacle - through applying a novel methodology. The analysis of this sport event is an interesting exercise in itself, since it allows achieving important lessons and conclusions. Yet, the scope of this paper is broader, including another major goal. Effectively, the present study illustrates the potential capacity that ESIrg methodology has for evaluating intangible assets of different types and character (that must not necessary be linked to the sport industry.

  13. Cortical and trabecular morphology is altered in the limb bones of mice artificially selected for faster skeletal growth.

    Science.gov (United States)

    Farooq, Saira; Leussink, Shannon; Sparrow, Leah M; Marchini, Marta; Britz, Hayley M; Manske, Sarah L; Rolian, Campbell

    2017-09-05

    Bone strength is influenced by mineral density and macro- and microstructure. Research into factors that contribute to bone morphology and strength has focused on genetic, environmental and morphological factors (e.g., body mass index), but little is known regarding the impact of rates of skeletal elongation on adult skeletal morphology and strength. Using micro-CT, we examined the impact of rates of skeletal elongation on bone cortical and trabecular morphology, and on rates of estrogen-dependent bone loss in the tibia in CD-1 mice, and in mice with accelerated skeletal growth (Longshanks). Groups of adult mice (n = 7/group) were subjected to ovariectomy or sham surgeries, scanned for 6 weeks, and indices of bone morphology were collected. Results show that Longshanks mice had significantly less trabecular bone at skeletal maturity, characterized by fewer, thinner trabeculae, and furthermore lost trabecular bone more slowly in response to ovariectomy. Artificial selection for rapid skeletal growth relative to somatic growth thus had a significant impact on trabecular bone morphology in Longshanks. Our data do not unequivocally demonstrate a causal relationship between rapid bone growth and reduced trabecular bone quality, but suggest that rapid linear bone growth may influence the risk of cancellous bone fragility.

  14. An over-nonlocal implicit gradient-enhanced damage-plastic model for trabecular bone under large compressive strains.

    Science.gov (United States)

    Hosseini, Hadi S; Horák, Martin; Zysset, Philippe K; Jirásek, Milan

    2015-11-01

    Investigation of trabecular bone strength and compaction is important for fracture risk prediction. At 1-2% compressive strain, trabecular bone undergoes strain softening, which may lead to numerical instabilities and mesh dependency in classical local damage-plastic models. The aim of this work is to improve our continuum damage-plastic model of bone by reducing the influence of finite element mesh size under large compression. This spurious numerical phenomenon may be circumvented by incorporating the nonlocal effect of cumulated plastic strain into the constitutive law. To this end, an over-nonlocal implicit gradient model of bone is developed and implemented into the finite element software ABAQUS using a user element subroutine. The ability of the model to detect the regions of bone failure is tested against experimental stepwise loading data of 16 human trabecular bone biopsies. The numerical outcomes of the nonlocal model revealed reduction of finite element mesh dependency compared with the local damage-plastic model. Furthermore, it helped reduce the computational costs of large-strain compression simulations. To the best of our knowledge, the proposed model is the first to predict the failure and densification of trabecular bone up to large compression independently of finite element mesh size. The current development enables the analysis of trabecular bone compaction as in osteoporotic fractures and implant migration, where large deformation of bone plays a key role. Copyright © 2015 John Wiley & Sons, Ltd.

  15. Evaluation of bloodletting cupping therapy in the management of hypertension

    Directory of Open Access Journals (Sweden)

    Moawia M Al-Tabakha

    2018-01-01

    Full Text Available Background: Bloodletting cupping therapy (Hijama is a traditional alternative medicine practiced in different cultures. Claims about the therapeutic efficacy of Hijama in hypertension are contradictory. The aim of this project was to determine if Hijama therapy is beneficial in the treatment of patients with hypertension. Materials and Methods: In this retrospective study, 60 files for patients treated for hypertension, aged 40–60 years and whose systolic blood pressure (SBP is at least 140mm Hg, were used. The data from 30 patient files were obtained from three licensed Hijama centers (study group, whereas data from the rest of 30 patient files were collected from a hospital (control group. The data from Hijama centers included age, date of Hijama therapy, and blood pressure measured before each Hijama session. Both diastolic blood pressure (DBP and SBP data were obtained over 3-month period. Results: The results showed a significant reduction in SBP (P value < 0.01 over three sessions of wet cupping (from 149.2 to 130.8mm Hg, but this was not significant for DBP over three sessions (P = 0.074. The study also found that the mean SBP in the study group was 9.6mm Hg less than that in the control group (130.8 vs. 140.4mm Hg, P = 0.019, whereas there was no significant difference in DBP between the study group and the control group (87.0 vs. 86.0mm Hg, P = 0.75. Conclusions: Our study shows clear relationship between Hijama and the reduction and control of SBP in patients with hypertension. Therefore, Hijama can be used as an adjunct to conventional therapy, which may allow downtitration of given doses of antihypertensive drugs. The possible association of SBP reduction by Hijama and pain reduction needs an investigation.

  16. Evaluation of Bloodletting Cupping Therapy in the Management of Hypertension.

    Science.gov (United States)

    Al-Tabakha, Moawia M; Sameer, Farah Tariq; Saeed, Mai Hafiz; Batran, Rahaf Montaser; Abouhegazy, Nada Tarek; Farajallah, Alaa A

    2018-01-01

    Bloodletting cupping therapy (Hijama) is a traditional alternative medicine practiced in different cultures. Claims about the therapeutic efficacy of Hijama in hypertension are contradictory. The aim of this project was to determine if Hijama therapy is beneficial in the treatment of patients with hypertension. In this retrospective study, 60 files for patients treated for hypertension, aged 40-60 years and whose systolic blood pressure (SBP) is at least 140mm Hg, were used. The data from 30 patient files were obtained from three licensed Hijama centers (study group), whereas data from the rest of 30 patient files were collected from a hospital (control group). The data from Hijama centers included age, date of Hijama therapy, and blood pressure measured before each Hijama session. Both diastolic blood pressure (DBP) and SBP data were obtained over 3-month period. The results showed a significant reduction in SBP ( P value cupping (from 149.2 to 130.8mm Hg), but this was not significant for DBP over three sessions ( P = 0.074). The study also found that the mean SBP in the study group was 9.6mm Hg less than that in the control group (130.8 vs. 140.4mm Hg, P = 0.019), whereas there was no significant difference in DBP between the study group and the control group (87.0 vs. 86.0mm Hg, P = 0.75). Our study shows clear relationship between Hijama and the reduction and control of SBP in patients with hypertension. Therefore, Hijama can be used as an adjunct to conventional therapy, which may allow downtitration of given doses of antihypertensive drugs. The possible association of SBP reduction by Hijama and pain reduction needs an investigation.

  17. Age- and menopause-related bone loss compromise cortical and trabecular microstructure.

    Science.gov (United States)

    Seeman, Ego

    2013-10-01

    All factors influencing the material composition and structure of bone do so through the final common cellular pathways of modeling and remodeling. During growth, modeling, the formation of new bone in different locations without prior bone resorption, deposits matrix upon the periosteum, enlarging the cross-sectional area of bone. Concurrently, endocortical resorption excavates the medullary canal while remodeling, the resorption and deposition of bone in the same location, assembles cortical osteons, each with their central Haversian canal. The Haversian canals and the connecting Volkmann canals form an intracortical canal network that occupies 30% of the total cortical volume. The remaining 70% is mineralized bone matrix volume. Around midlife, in women, remodeling balance becomes negative; less bone is deposited than it is resorbed by each bone's basic multicellular units (BMUs), and remodeling rate increases; there are more BMUs removing bone upon its intracortical, endocortical, and trabecular surfaces. Canals enlarge and coalesce creating giant pores. Remodeling upon trabeculae removes them, whereas intracortical and endocortical remodeling cavitates and fragments the cortex. Bone loss becomes almost entirely cortical as trabeculae disappear. Remodeling removes more bone from a diminishing total mineralized bone matrix volume so that by old age, total mineralized bone matrix volume is halved; 70% of all bone loss is cortical because 80% of the skeleton is cortical; 30% of the bone loss arises from the 20% of the skeleton that is trabecular. Of all fractures occurring, 80% are nonvertebral and 20% are vertebral. The notion of osteoporosis as a disease of trabecular bone loss and vertebral fractures needs to be revised.

  18. Local bone enhancement fuzzy clustering for segmentation of MR trabecular bone images.

    Science.gov (United States)

    Folkesson, Jenny; Carballido-Gamio, Julio; Eckstein, Felix; Link, Thomas M; Majumdar, Sharmila

    2010-01-01

    Segmentation of trabecular bone from magnetic resonance (MR) images is a challenging task due to spatial resolution limitations, signal-to-noise ratio constraints, and signal intensity inhomogeneities. This article examines an alternative approach to trabecular bone segmentation using partial membership segmentation termed fuzzy C-means clustering incorporating local second order features for bone enhancement (BE-FCM) at multiple scales. This approach is meant to allow for a soft segmentation that accounts for partial volume effects while suppressing the influence of noise. A soft segmentation method was developed and evaluated on three different sets of data; interscan reproducibility was evaluated on six test-retest in vivo MR scans of the proximal femur, correlation between MR and HR-pQCT measurements was evaluated on 49 in vivo scans from the distal tibia, and the potential for fracture discrimination was evaluated using MR scans of calcaneus specimens from 15 participants with and 15 participants without vertebral fracture. The algorithm was compared to fuzzy clustering using the intensity as the only feature (I-FCM) and a dual thresholding algorithm. The metric evaluated was bone volume over total volume (BV/TV) within user-defined regions of interest. BE-FCM had a higher interscan reproducibility (rms CV: 2.0%) compared to I-FCM (5.6%) and thresholding (4.2%), and expressed higher correlation to HR-pQCT data (r = 0.79, p control and a vertebral fracture group at a 95% significance level. The results suggest that trabecular bone segmentation by BE-FCM can provide a precise BV/TV measurement that is sensitive to pathology. The segmentation method may become useful in MR imaging-based quantification of bone microarchitecture.

  19. Characterizing trabecular bone structure for assessing vertebral fracture risk on volumetric quantitative computed tomography

    Science.gov (United States)

    Nagarajan, Mahesh B.; Checefsky, Walter A.; Abidin, Anas Z.; Tsai, Halley; Wang, Xixi; Hobbs, Susan K.; Bauer, Jan S.; Baum, Thomas; Wismüller, Axel

    2015-03-01

    While the proximal femur is preferred for measuring bone mineral density (BMD) in fracture risk estimation, the introduction of volumetric quantitative computed tomography has revealed stronger associations between BMD and spinal fracture status. In this study, we propose to capture properties of trabecular bone structure in spinal vertebrae with advanced second-order statistical features for purposes of fracture risk assessment. For this purpose, axial multi-detector CT (MDCT) images were acquired from 28 spinal vertebrae specimens using a whole-body 256-row CT scanner with a dedicated calibration phantom. A semi-automated method was used to annotate the trabecular compartment in the central vertebral slice with a circular region of interest (ROI) to exclude cortical bone; pixels within were converted to values indicative of BMD. Six second-order statistical features derived from gray-level co-occurrence matrices (GLCM) and the mean BMD within the ROI were then extracted and used in conjunction with a generalized radial basis functions (GRBF) neural network to predict the failure load of the specimens; true failure load was measured through biomechanical testing. Prediction performance was evaluated with a root-mean-square error (RMSE) metric. The best prediction performance was observed with GLCM feature `correlation' (RMSE = 1.02 ± 0.18), which significantly outperformed all other GLCM features (p < 0.01). GLCM feature correlation also significantly outperformed MDCTmeasured mean BMD (RMSE = 1.11 ± 0.17) (p< 10-4). These results suggest that biomechanical strength prediction in spinal vertebrae can be significantly improved through characterization of trabecular bone structure with GLCM-derived texture features.

  20. Effect of swimming exercise on three-dimensional trabecular bone microarchitecture in ovariectomized rats.

    Science.gov (United States)

    Ju, Yong-In; Sone, Teruki; Ohnaru, Kazuhiro; Tanaka, Kensuke; Fukunaga, Masao

    2015-11-01

    Swimming is generally considered ineffective for increasing bone mass in humans, at least compared with weight-bearing sports. However, swimming exercise has sometimes been shown to have a strong positive effect on bone mass in small animals. This study investigated the effects of swimming on bone mass, strength, and microarchitecture in ovariectomized (OVX) rats. OVX or sham operations were performed on 18-wk-old female Fisher 344 rats. Rats were randomly divided into four groups: sham sedentary (Sham-CON), sham swimming exercised (Sham-SWI), OVX sedentary (OVX-CON), and OVX swimming exercised (OVX-SWI). Rats in exercise groups performed swimming in a water bath for 60 min/day, 5 days/wk, for 12 wk. Bone mineral density (BMD) in right femurs was analyzed using dual-energy X-ray absorptiometry. Three-dimensional trabecular architecture at the distal femoral metaphysis was analyzed using microcomputed tomography (μCT). Geometrical properties of diaphyseal cortical bone were evaluated in the midfemoral region using μCT. The biomechanical properties of femurs were analyzed using three-point bending. Femoral BMD was significantly decreased following ovariectomy. This change was suppressed by swimming. Trabecular bone thickness, number, and connectivity were decreased by ovariectomy, whereas structure model index (i.e., ratio of rod-like to plate-like trabeculae) increased. These changes were also suppressed by swimming exercise. Femurs displayed greater cortical width and maximum load in SWI groups than in CON groups. Together, these results demonstrate that swimming exercise drastically alleviated both OVX-induced decreases in bone mass and mechanical strength and the deterioration of trabecular microarchitecture in rat models of osteoporosis. Copyright © 2015 the American Physiological Society.

  1. Inhibition of hyaluronan synthesis reduces versican and fibronectin levels in trabecular meshwork cells.

    Directory of Open Access Journals (Sweden)

    Kate E Keller

    Full Text Available Hyaluronan (HA is a major component of the extracellular matrix (ECM and is synthesized by three HA synthases (HAS. Similarities between the HAS2 knockout mouse and the hdf mutant mouse, which has a mutation in the versican gene, suggest that HA and versican expression may be linked. In this study, the relationship between HA synthesis and levels of versican, fibronectin and several other ECM components in trabecular meshwork cells from the anterior segment of the eye was investigated. HA synthesis was inhibited using 4-methylumbelliferone (4MU, or reduced by RNAi silencing of each individual HAS gene. Quantitative RT-PCR and immunoblotting demonstrated a reduction in mRNA and protein levels of versican and fibronectin. Hyaluronidase treatment also reduced versican and fibronectin levels. These effects could not be reversed by addition of excess glucose or glucosamine or exogenous HA to the culture medium. CD44, tenascin C and fibrillin-1 mRNA levels were reduced by 4MU treatment, but SPARC and CSPG6 mRNA levels were unaffected. Immunostaining of trabecular meshwork tissue after exposure to 4MU showed an altered localization pattern of HA-binding protein, versican and fibronectin. Reduction of versican by RNAi silencing did not affect HA concentration as assessed by ELISA. Together, these data imply that HA concentration affects synthesis of certain ECM components. Since precise regulation of the trabecular meshwork ECM composition and organization is required to maintain the aqueous humor outflow resistance and intraocular pressure homeostasis in the eye, coordinated coupling of HA levels and several of its ECM binding partners should facilitate this process.

  2. Comparative analysis of trabecular bone structure and orientation in South African hominin tali.

    Science.gov (United States)

    Su, Anne; Carlson, Kristian J

    2017-05-01

    Tali of several hominin taxa are preserved in the fossil record and studies of the external morphology of these often show a mosaic of human-like and ape-like features. This has contributed to a growing recognition of variability characterizing locomotor kinematics of Australopithecus. In contrast, locomotor kinematics of another Plio-Pleistocene hominin, Paranthropus, are substantially less well-documented, in part, because of the paucity of postcranial fossils securely attributed to the genus. Since the talus transmits locomotor-based loads through the ankle and its internal structure is hypothesized to reflect accommodation to such loads, it is a cornerstone structure for reconstructing locomotor kinematics. Here we quantify and characterize trabecular bone morphology within tali attributed to Australopithecus africanus (StW 102, StW 363, StW 486) and Paranthropus robustus (TM 1517), making quantitative comparisons to modern humans, extant non-human apes, baboons, and a hominin talus attributed to Paranthropus boisei (KNM-ER 1464). Using high-resolution images of fossil tali (25 μm voxels), nine trabecular bone subregions of interest beneath the articular surface of the talar trochlea were segmented to quantify localized patterns in distribution and primary strut orientation. It was found that trabecular strut orientation and shape, in some cases, can discriminate amongst species characterized by different locomotor foot kinematics. Discriminant function analyses using standard trabecular bone structural properties align TM 1517 with Pan and Gorilla, while other hominin tali structurally most resemble those of baboons. In primary strut orientation, Paranthropus tali (KNM-ER 1464 and TM 1517) resemble the human condition in the anterior-medial subregion, where strut orientation appears positioned to distribute compressive loads medially and distally toward the talar head. In A. africanus tali (particularly StW 486), primary strut orientation in this region

  3. Three-dimensional quantification of structures in trabecular bone using measures of complexity

    DEFF Research Database (Denmark)

    Marwan, Norbert; Kurths, Jürgen; Thomsen, Jesper Skovhus

    2009-01-01

    evaluate different aspects of organization and complexity of 3D structures, such as complexity of its surface or shape variability. We apply these measures to 3D data acquired by high-resolution microcomputed tomography (µCT) from human proximal tibiae and lumbar vertebrae at different stages...... of osteoporotic bone loss. The outcome is compared to the results of conventional static histomorphometry and exhibits clear relationships between the analyzed geometrical features of trabecular bone and loss of bone density, but also indicate that the measures reveal additional information about the structural...

  4. Trabecular bone structural parameters evaluated using dental cone-beam computed tomography: cellular synthetic bones.

    Science.gov (United States)

    Ho, Jung-Ting; Wu, Jay; Huang, Heng-Li; Chen, Michael Y c; Fuh, Lih-Jyh; Hsu, Jui-Ting

    2013-11-09

    This study compared the adequacy of dental cone beam computed tomography (CBCT) and micro computed tomography (micro-CT) in evaluating the structural parameters of trabecular bones. The cellular synthetic bones in 4 density groups (Groups 1-4: 0.12, 0.16, 0.20, and 0.32 g/cm3) were used in this study. Each group comprised 8 experimental specimens that were approximately 1 cm3. Dental CBCT and micro-CT scans were conducted on each specimen to obtain independent measurements of the following 4 trabecular bone structural parameters: bone volume fraction (BV/TV), specific bone surface (BS/BV), trabecular thickness (Tb.Th.), and trabecular separation (Tb.Sp.). Wilcoxon signed ranks tests were used to compare the measurement variations between the dental CBCT and micro-CT scans. A Spearman analysis was conducted to calculate the correlation coefficients (r) of the dental CBCT and micro-CT measurements. Of the 4 groups, the BV/TV and Tb.Th. measured using dental CBCT were larger compared with those measured using micro-CT. By contrast, the BS/BV measured using dental CBCT was significantly less compared with those measured using micro-CT. Furthermore, in the low-density groups (Groups 1 and 2), the Tb.Sp. measured using dental CBCT was smaller compared with those measured using micro-CT. However, the Tb.Sp. measured using dental CBCT was slightly larger in the high-density groups (Groups 3 and 4) than it was in the low density groups. The correlation coefficients between the BV/TV, BS/BV, Tb.Th., and Tb.Sp. values measured using dental CBCT and micro-CT were 0.9296 (p < .001), 0.8061 (p < .001), 0.9390 (p < .001), and 0.9583 (p < .001), respectively. Although the dental CBCT and micro-CT approaches exhibited high correlations, the absolute values of BV/TV, BS/BV, Tb.Th., Tb.Sp. differed significantly between these measurements. Additional studies must be conducted to evaluate using dental CBCT in clinical practice.

  5. [Effect of cupping on hemodynamic levels in the regional sucked tissues in patients with lumbago].

    Science.gov (United States)

    Tang, Xiao; Xiao, Xue-Hua; Zhang, Guo-Qing

    2012-10-01

    To observe hemodynamic changes in the local sucked tissue of lower back undergoing negative pressure after cupping in patients with lumbago. Twenty-two lumbago outpatients were recruited in the present study and 32 sucked tissues accepted measurements. The cupping was applied to the tenderpoint of the patients' lower back for 10 min by using a glass-mug (5 cm in diameter). Hemodynamic indexes [peak systolic velocity (PSV), end-diastolic velocity (EDV) and resistance index (RI)] of the sucked skin and subcutaneous tissues at the lower back were detected before and after cupping by using a color Doppler flow imaging. After cupping intervention at the lower back, the PSV [(14.2 +/- 1.8) cm/s] and EDV [(5.5 +/- 0.7) cm/s] levels were increased significantly in comparison with those [(5.9 +/- 0.9) and (1.9 +/- 0.3) cm/s] before cupping (P cupping (0.61 +/- 0.05 vs 0.68 +/- 0.06, P Cupping therapy can increase the peak systolic velocity and end-diastolic velocity and lower vascular resistance of the subcutaneous arterioles in the regional tissue, which may contribute to its effect in relieving lumbago.

  6. Effects of traditional cupping therapy in patients with carpal tunnel syndrome: a randomized controlled trial.

    Science.gov (United States)

    Michalsen, Andreas; Bock, Silke; Lüdtke, Rainer; Rampp, Thomas; Baecker, Marcus; Bachmann, Jürgen; Langhorst, Jost; Musial, Frauke; Dobos, Gustav J

    2009-06-01

    We investigated the effectiveness of cupping, a traditional method of treating musculoskeletal pain, in patients with carpal tunnel syndrome (CTS) in an open randomized trial. n = 52 outpatients (58.5 +/- 8.0 years) with neurologically confirmed CTS were randomly assigned to either a verum (n = 26) or a control group (n = 26). Verum patients were treated with a single application of wet cupping, and control patients with a single local application of heat within the region overlying the trapezius muscle. Patients were followed up on day 7 after treatment. The primary outcome, severity of CTS symptoms (VAS), was reduced from 61.5 +/- 20.5 to 24.6 +/- 22.7 mm at day 7 in the cupping group and from 67.1 +/- 20.2 to 51.7 +/- 23.9 mm in the control group [group difference -24.5mm (95%CI -36.1; -2.9, P cupping therapy may be effective in relieving the pain and other symptoms related to CTS. The efficacy of cupping in the long-term management of CTS and related mechanisms remains to be clarified. The results of a randomized trial on the clinical effects of traditional cupping therapy in patients with carpal tunnel syndrome are presented. Cupping of segmentally related shoulder zones appears to alleviate the symptoms of carpal tunnel syndrome.

  7. A Facile Approach to Evaluate Thermal Insulation Performance of Paper Cups

    Directory of Open Access Journals (Sweden)

    Yudi Kuang

    2015-01-01

    Full Text Available Paper cups are ubiquitous in daily life for serving water, soup, coffee, tea, and milk due to their convenience, biodegradability, recyclability, and sustainability. The thermal insulation performance of paper cups is of significance because they are used to supply hot food or drinks. Using an effective thermal conductivity to accurately evaluate the thermal insulation performance of paper cups is complex due to the inclusion of complicated components and a multilayer structure. Moreover, an effective thermal conductivity is unsuitable for evaluating thermal insulation performance of paper cups in the case of fluctuating temperature. In this work, we propose a facile approach to precisely analyze the thermal insulation performance of paper cups in a particular range of temperature by using an evaluation model based on the MISO (Multiple-Input Single-Output technical theory, which includes a characterization parameter (temperature factor and a measurement apparatus. A series of experiments was conducted according to this evaluation model, and the results show that this evaluation model enables accurate characterization of the thermal insulation performance of paper cups and provides an efficient theoretical basis for selecting paper materials for paper cups.

  8. Why it is harder to run RoboCup in South Africa

    Directory of Open Access Journals (Sweden)

    Alexander Ferrein

    2016-10-01

    Full Text Available Robots are widely used as a vehicle to spark interest in science and technology in learners. A number of initiatives focus on this issue, for instance, the Roberta Initiative, the FIRST Lego League, the World Robot Olympiad and RoboCup Junior. Robotic competitions are valuable not only for school learners but also for university students, as the RoboCup initiative shows. Besides technical skills, the students get some project exposure and experience what it means to finish their tasks on time. But qualifying students for future high-tech areas should not only be for students from developed countries. In this article, we present our experiences with research and education in robotics within the RoboCup initiative, in Germany and South Africa; we report on our experiences with trying to get the RoboCup initiative in South Africa going. RoboCup has a huge support base of academic institutions in Germany; this is not the case in South Africa. We present our ‘north–south’ collaboration initiatives in RoboCup between Germany and South Africa and discuss some of the reasons why we think it is harder to run RoboCup in South Africa.

  9. Fabrication of Faraday Cup Array for the Measurement of 2-Dimensional Proton Beam Profile

    International Nuclear Information System (INIS)

    Jung, Myunghwan; Kim, Bom Sok; Kim, Kyeryung

    2014-01-01

    It has an advantage of easy-to-use and possible to visually check, immediately; on the other hand, the measurement range is very limited. Another method is using the CCD camera-scintillator device such as p43 phosphor screen or chromox. A variety of faraday cup detectors have been recently introduced. The faraday cup is one of the powerful and popular tools for the measurement of beam current. By using several faraday cups in array geometry, it is possible to observe current distribution. In this study, we developed an external faraday cup array for the measure the beam current and profile at a KOMAC (Korea Multi-purpose Accelerator Complex) beam utilization facility. To measure the beam profile, before fabrication of faraday cup array, we use gafchromic film. By making the faraday cup array we were able to reduce the consumption of Gafchromic film and a more accurate diagnosis of the proton beam is possible. The use of faraday cup array, experiment using the proton beam is more reliable and confident

  10. The Transverse Acetabular Ligament as an Intraoperative Guide to Cup Abduction.

    Science.gov (United States)

    Hiddema, Willem B; van der Merwe, Johan F; van der Merwe, Werner

    2016-07-01

    The success of a total hip arthroplasty relies on optimal acetabular cup placement to ensure mating of the femoral head and acetabular cup throughout all positions of the hip joint. Poor cup placement is associated with dislocation, impingement, microseparation, component loosening, and accelerated wear due to rim loading. This study examined a novel method of using the transverse acetabular ligament (TAL) to guide cup inclination during primary total hip arthroplasty. A descriptive study using 16 hips from 9 cadavers. A computer navigation system measured inclination and version of the acetabular component in 3 positions with the lower edge of cup: (1) flush with, (2) 5 mm proximal to, and (3) 5 mm distal to free border of the TAL. The median inclination angles were 44° in position (1), 30° in position (2), and 64° in position (3). The median anteversion angle for all positions was 19°. Cup inclination was acceptable when the lower edge of the cup was flush or within 5 mm proximal to the TAL. Copyright © 2016 Elsevier Inc. All rights reserved.

  11. Prediction of specialty coffee cup quality based on near infrared spectra of green coffee beans.

    Science.gov (United States)

    Tolessa, Kassaye; Rademaker, Michael; De Baets, Bernard; Boeckx, Pascal

    2016-04-01

    The growing global demand for specialty coffee increases the need for improved coffee quality assessment methods. Green bean coffee quality analysis is usually carried out by physical (e.g. black beans, immature beans) and cup quality (e.g. acidity, flavour) evaluation. However, these evaluation methods are subjective, costly, time consuming, require sample preparation and may end up in poor grading systems. This calls for the development of a rapid, low-cost, reliable and reproducible analytical method to evaluate coffee quality attributes and eventually chemical compounds of interest (e.g. chlorogenic acid) in coffee beans. The aim of this study was to develop a model able to predict coffee cup quality based on NIR spectra of green coffee beans. NIR spectra of 86 samples of green Arabica beans of varying quality were analysed. Partial least squares (PLS) regression method was used to develop a model correlating spectral data to cupping score data (cup quality). The selected PLS model had a good predictive power for total specialty cup quality and its individual quality attributes (overall cup preference, acidity, body and aftertaste) showing a high correlation coefficient with r-values of 90, 90,78, 72 and 72, respectively, between measured and predicted cupping scores for 20 out of 86 samples. The corresponding root mean square error of prediction (RMSEP) was 1.04, 0.22, 0.27, 0.24 and 0.27 for total specialty cup quality, overall cup preference, acidity, body and aftertaste, respectively. The results obtained suggest that NIR spectra of green coffee beans are a promising tool for fast and accurate prediction of coffee quality and for classifying green coffee beans into different specialty grades. However, the model should be further tested for coffee samples from different regions in Ethiopia and test if one generic or region-specific model should be developed. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. FLOW (finding lasting options for women): multicentre randomized controlled trial comparing tampons with menstrual cups.

    Science.gov (United States)

    Howard, Courtney; Rose, Caren Lee; Trouton, Konia; Stamm, Holly; Marentette, Danielle; Kirkpatrick, Nicole; Karalic, Sanja; Fernandez, Renee; Paget, Julie

    2011-06-01

    To determine whether menstrual cups are a viable alternative to tampons. Randomized controlled trial. Prince George, Victoria, and Vancouver, BC. A total of 110 women aged 19 to 40 years who had previously used tampons as their main method of menstrual management. Participants were randomized into 2 groups, a tampon group and a menstrual cup group. Using online diaries, participants tracked 1 menstrual cycle using their regular method and 3 menstrual cycles using the method of their allocated group. Overall satisfaction; secondary outcomes included discomfort, urovaginal infection, cost, and waste. Forty-seven women in each group completed the final survey, 5 of whom were subsequently excluded from analysis (3 from the tampon group and 2 from the menstrual cup group). Overall satisfaction on a 7-point Likert scale was higher for the menstrual cup group than for the tampon group (mean [standard deviation] score 5.4 [1.5] vs 5.0 [1.0], respectively; P=.04). Approximately 91% of women in the menstrual cup group said they would continue to use the cup and recommend it to others. Women used a median of 13 menstrual products per cycle, or 169 products per year, which corresponds to approximately 771,248,400 products used annually in Canada. Estimated cost for tampon use was $37.44 a year (similar to the retail cost of 1 menstrual cup). Subjective vaginal discomfort was initially higher in the menstrual cup group, but the discomfort decreased with continued use. There was no significant difference in physician-diagnosed urovaginal symptoms between the 2 groups. Both of the menstrual management methods evaluated were well tolerated by subjects. Menstrual cups are a satisfactory alternative to tampons and have the potential to be a sustainable solution to menstrual management, with moderate cost savings and much-reduced environmental effects compared with tampons. Trial registration number C06-0478 (ClinicalTrials.gov).

  13. ACCUWIND - Classification of five cup anemometers according to IEC 61400-12-1

    DEFF Research Database (Denmark)

    Friis Pedersen, Troels; Dahlberg, J.-Å.; Busche, P.

    2006-01-01

    -gust tests, torque coefficient curve measurements for non-tilted conditions; rotor inertia measurements and measurements of friction of bearings at temperatures -10°C to 40°C. The characteristics are fitted to twodifferent time domain cup anemometer models, and simulations of the cup anemometers are made......The characteristics of five cup anemometers were investigated in detail, and data are presented in figures and tables. The characteristics include: normal wind tunnel calibrations; angular response measurements at 5, 8 and 11m/s; torque coefficient curvemeasurements from combined tilt and ramp...

  14. Cervical spinal epidural abscess following acupuncture and wet-cupping therapy: A case report.

    Science.gov (United States)

    Yao, Yindan; Hong, Wenke; Chen, Huimin; Guan, Qiongfeng; Yu, Hu; Chang, Xianchao; Yu, Yaoping; Xu, Shanhu; Fan, Weinv

    2016-02-01

    Report of an uncommon complication of acupuncture and wet cupping. A 54-year-old man presented with neck pain and fever. Magnetic resonance imaging of the cervical spine revealed an epidural abscess at C4 to T2. The symptoms related to epidural abscess resolved partially after treatment with antibiotics. Acupuncture and wet-cupping therapy should be taken into consideration as a cause of spinal epidural abscesses in patients who present with neck pain and fever. Furthermore, acupuncture and wet-cupping practitioners should pay attention to hygienic measures. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Is Cup Positioning Challenged in Hips Previously Treated With Periacetabular Osteotomy?

    DEFF Research Database (Denmark)

    Hartig-Andreasen, Charlotte; Stilling, Maiken; Søballe, Kjeld

    2014-01-01

    After periacetabular osteotomy (PAO), some patients develop osteoarthritis with need of a total hip arthroplasty (THA). We evaluated the outcome of THA following PAO and explored factors associated with inferior cup position and increased polyethylene wear. Follow-up were performed 4 to 10years...... after THA in 34 patients (38 hips) with previous PAO. Computer analysis evaluated cup position and wear rates. No patient had dislocations or revision surgery. Median scores were: Harris hip 96, Oxford hip 38 and WOMAC 78. Mean cup anteversion and abduction angles were 22(o) (range 7°-43°) and 45...

  16. Does osteoporosis reduce the primary tilting stability of cementless acetabular cups?

    Science.gov (United States)

    von Schulze Pellengahr, Christoph; von Engelhardt, Lars V; Wegener, Bernd; Müller, Peter E; Fottner, Andreas; Weber, Patrick; Ackermann, Ole; Lahner, Matthias; Teske, Wolfram

    2015-04-21

    Cementless hip cups need sufficient primary tilting stability to achieve osseointegration. The aim of the study was to assess differences of the primary implant stability in osteoporotic bone and in bone with normal bone density. To assess the influence of different cup designs, two types of threaded and two types of press-fit cups were tested. The maximum tilting moment for two different cementless threaded cups and two different cementless press-fit cups was determined in macerated human hip acetabuli with reduced (n=20) and normal bone density (n=20), determined using Q-CT. The tilting moments for each cup were determined five times in the group with reduced bone density and five times in the group with normal bone density, and the respective average values were calculated. The mean maximum extrusion force of the threaded cup Zintra was 5670.5 N (max. tilting moment 141.8 Nm) in bone with normal density and.5748.3 N (max. tilting moment 143.7 Nm) in osteoporotic bone. For the Hofer Imhof (HI) threaded cup it was 7681.5 N (192.0 Nm) in bone with normal density and 6828.9 N (max. tilting moment 170.7 Nm) in the group with osteoporotic bone. The mean maximum extrusion force of the macro-textured press-fit cup Metallsockel CL was 3824.6 N (max. tilting moment 95.6 Nm) in bone with normal and 2246.2 N (max. tilting moment 56.2 Nm) in osteoporotic bone. For the Monoblock it was 1303.8 N (max. tilting moment 32.6 Nm) in normal and 1317 N (max. tilting moment 32.9 Nm) in osteoporotic bone. There was no significance. A reduction of the maximum tilting moment in osteoporotic bone of the ESKA press-fit cup Metallsockel CL was noticed. Results on macerated bone specimens showed no statistically significant reduction of the maximum tilting moment in specimens with osteoporotic bone density compared to normal bone, neither for threaded nor for the press-fit cups. With the limitation that the results were obtained using macerated bone, we could not detect any restrictions for

  17. Faraday cup for electron flux measurements on the microtron MT 25

    International Nuclear Information System (INIS)

    Vognar, M.; Simane, C.; Chvatil, D.

    2001-01-01

    The basic design criteria for construction of an evacuated Faraday cup for precise measurement of 5-25 MeV electron beam currents in air from a microtron are characterized. The homemade Faraday cup is described along with the electronic chain and its incorporation into the measuring beam line. The provisions applied to reduce backward electron escape are outlined. The current range was 10 -5 to 10 -10 A. The diameter of the Al entrance window of the Faraday cup was 1.8 cm, its area was 2.54 cm 2 and thickness 0.1 mm

  18. Histomorphometric study of trabecular bone remodeling during condylar process fracture healing in the growing period: experimental study.

    Science.gov (United States)

    Yasuoka, T; Oka, N

    1991-09-01

    Trabecular bone remodeling during condylar fracture healing in the growing period was analyzed by histomorphometry with a synchronous system. Data from the study showed displacement of the fractured condyle was compensated by the changes in remodeling ascribed to the pubertal spurt of growth, and that such remodeling still continued even after clinical healing. The regional acceleratory phenomenon, evolved to potentiate tissue healing, was observed 1 week after induction of the fracture. Mesenchymal cells were presumably modulated into chondroblasts that promoted endochondral ossification. It was concluded that trabecular bone remodeling plays an important role in healing of condylar fractures during the growth period.

  19. Micro-CT characterization of human trabecular bone in osteogenesis imperfecta

    Science.gov (United States)

    Jameson, John; Albert, Carolyne; Smith, Peter; Molthen, Robert; Harris, Gerald

    2011-03-01

    Osteogenesis imperfecta (OI) is a genetic syndrome affecting collagen synthesis and assembly. Its symptoms vary widely but commonly include bone fragility, reduced stature, and bone deformity. Because of the small size and paucity of human specimens, there is a lack of biomechanical data for OI bone. Most literature has focused on histomorphometric analyses, which rely on assumptions to extrapolate 3-D properties. In this study, a micro-computed tomography (μCT) system was used to directly measure structural and mineral properties in pediatric OI bone collected during routine surgical procedures. Surface renderings suggested a poorly organized, plate-like orientation. Patients with a history of bone-augmenting drugs exhibited increased bone volume fraction (BV/TV), trabecular number (Tb.N), and connectivity density (Eu.Conn.D). The latter two parameters appeared to be related to OI severity. Structural results were consistently higher than those reported in a previous histomorphometric study, but these differences can be attributed to factors such as specimen collection site, drug therapy, and assumptions associated with histomorphometry. Mineral testing revealed strong correlations with several structural parameters, highlighting the importance of a dual approach in trabecular bone testing. This study reports some of the first quantitative μCT data of human OI bone, and it suggests compelling possibilities for the future of OI bone assessment.

  20. Relationship between the morphologic features of alveolar trabecular bone and systemic osteoporosis

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chang Jin; Chang, Hoon Sang; Lee, Byung Do [Wonkwang University College of Medicine, Iksan (Korea, Republic of)

    2005-09-15

    The purpose of this study was to investigate the preliminary use of morphologic operation (MO) in analyzing trabecular pattern of alveolar bone for the predicting systemic osteoporosis. Study subjects consisted of 35 females (average age 48.5 years) and 25 males (average age 25.8 years). Bone mineral density BMD (grams/cm) of lumbar spine and proximal femur of these subjects were measured by a dual energy X-ray absorptiometry (DEXA). Regions of interest (ROIs) were selected from the digitized peri apical radiographs of subjects' posterior jaw. A custom computer program processed morphology operations of ROIs. We compared mean values of 11 MO variables according to the osteoporotic group divided by the T-scores of DEXA. We also studied correlation between radiographic density and these MO variables. The mean radiographic densities insignificantly correlated with MO variables. There were statistically significant differences among the values of 9 MO variables according to the osteoporotic group. Morphologic operation can be effective in analyzing trabecular pattern of alveolar bone for the predicting osteoporosis.

  1. Spatial correlations of trabecular bone microdamage with local stresses and strains using rigid image registration.

    Science.gov (United States)

    Nagaraja, Srinidhi; Skrinjar, Oskar; Guldberg, Robert E

    2011-06-01

    Although microdamage is known to accumulate in trabecular bone with overloading and aging, the tissue-level stresses and strains associated with local bone failure are not well known. Local correlation of microdamage with microstructural stresses and strains requires methods to accurately register histological sections with micro-computed tomography (micro-CT) based finite element models. In addition, the resolution of correlation (i.e., grid size) selected for analysis may affect the observed results. Therefore, an automated, repeatable, and accurate image registration algorithm was developed to determine the range of local stresses and strains associated with microdamage initiation. Using a two-dimensional rigid registration algorithm, bone structures from histology and micro-CT imaging were aligned. Once aligned, microdamaged regions were spatially correlated with local stresses and strains obtained from micro-CT based finite element analysis. Using this more sophisticated registration technique, we were able to analyze the effects of varying spatial grid resolution on local stresses and strains initiating microdamage. The results indicated that grid refinement to the individual pixel level (pixel-by-pixel method) more precisely defined the range of microdamage initiation compared to manually selected individual damaged and undamaged trabeculae. Using the pixel-by-pixel method, we confirmed that trabecular bone from younger cows sustained higher local strains prior to microdamage initiation compared to older bone.

  2. Anatomical variations of trabecular bone structure in intraoral radiographs using fractal and particles count analyses

    International Nuclear Information System (INIS)

    Amer, Maha Eshak; Heo, Min Suk; Brooks, Sharon L; Benavides, Erika

    2012-01-01

    This study was performed to evaluate possible variations in maxillary and mandibular bone texture of normal population using the fractal analysis, particles count, and area fraction in intraoral radiographs. Periapical radiographs of patients who had full mouth intraoral radiographs were collected. Regions of interest (100X100 pixels) were located between the teeth of the maxillary anterior, premolar, and molar area, as well as the mandibular anterior, premolar, and molar areas. The fractal dimension (FD) was calculated by using the box counting method. The particle count (PC) and area fraction (AF) analyses were also performed. There was no significant difference in the FD values among the different groups of age, gender, upper, and lower jaws. The mean FD value was 1.49±0.01. The mean PC ranged from 44 to 54, and the mean AF ranged from 10.92 to 11.85. The values of FD, PC, and AF were significantly correlated with each other except for the upper molar area. According to the results, patients with normal trabecular pattern showed a FD of approximately 1.5. Based on these results, further investigation would be recommended if the FD value of patient significantly different from this number, since the alteration of this value indicates microstructural modification of trabecular pattern of the jaws. Additionally, with periapical radiographs, simple and cost-effective, PC and AF could be used to assess the deviation from the normal.

  3. Assessment of trabecular bone changes around endosseous implants using image analysis techniques: A preliminary study

    International Nuclear Information System (INIS)

    Zuki, Mervet El; Omami, Galal; Horner, Keith

    2014-01-01

    The objective of this study was to assess the trabecular bone changes that occurred around functional endosseous dental implants by means of radiographic image analysis techniques. Immediate preoperative and postoperative periapical radiographs of de-identified implant patients at the University Dental Hospital of Manchester were retrieved, screened for specific inclusion criteria, digitized, and quantified for structural elements of the trabecular bone around the endosseous implants, by using image analysis techniques. Data were analyzed using SPSS version 11.5. P values of less than 0.05 were considered statistically significant. A total of 12 implants from 11 patients were selected for the study, and 26 regions of interest were obtained. There was a significant increase in the bone area in terms of the mean distance between nodes (p=0.006) and a significant decrease in the marrow area in terms of the bone area (p=0.006) and the length of marrow spaces (p=0.032). It appeared that the bone around the implant underwent remodeling that resulted in a net increase in bone after implant placement.

  4. Trabecular bone score (TBS) as a new complementary approach for osteoporosis evaluation in clinical practice.

    Science.gov (United States)

    Harvey, N C; Glüer, C C; Binkley, N; McCloskey, E V; Brandi, M-L; Cooper, C; Kendler, D; Lamy, O; Laslop, A; Camargos, B M; Reginster, J-Y; Rizzoli, R; Kanis, J A

    2015-09-01

    Trabecular bone score (TBS) is a recently-developed analytical tool that performs novel grey-level texture measurements on lumbar spine dual X-ray absorptiometry (DXA) images, and thereby captures information relating to trabecular microarchitecture. In order for TBS to usefully add to bone mineral density (BMD) and clinical risk factors in osteoporosis risk stratification, it must be independently associated with fracture risk, readily obtainable, and ideally, present a risk which is amenable to osteoporosis treatment. This paper summarizes a review of the scientific literature performed by a Working Group of the European Society for Clinical and Economic Aspects of Osteoporosis and Osteoarthritis. Low TBS is consistently associated with an increase in both prevalent and incident fractures that is partly independent of both clinical risk factors and areal BMD (aBMD) at the lumbar spine and proximal femur. More recently, TBS has been shown to have predictive value for fracture independent of fracture probabilities using the FRAX® algorithm. Although TBS changes with osteoporosis treatment, the magnitude is less than that of aBMD of the spine, and it is not clear how change in TBS relates to fracture risk reduction. TBS may also have a role in the assessment of fracture risk in some causes of secondary osteoporosis (e.g., diabetes, hyperparathyroidism and glucocorticoid-induced osteoporosis). In conclusion, there is a role for TBS in fracture risk assessment in combination with both aBMD and FRAX. Copyright © 2015 Elsevier Inc. All rights reserved.

  5. Trabecular evidence for a human-like gait in Australopithecus africanus.

    Directory of Open Access Journals (Sweden)

    Meir M Barak

    Full Text Available Although the earliest known hominins were apparently upright bipeds, there has been mixed evidence whether particular species of hominins including those in the genus Australopithecus walked with relatively extended hips, knees and ankles like modern humans, or with more flexed lower limb joints like apes when bipedal. Here we demonstrate in chimpanzees and humans a highly predictable and sensitive relationship between the orientation of the ankle joint during loading and the principal orientation of trabecular bone struts in the distal tibia that function to withstand compressive forces within the joint. Analyses of the orientation of these struts using microCT scans in a sample of fossil tibiae from the site of Sterkfontein, of which two are assigned to Australopithecus africanus, indicate that these hominins primarily loaded their ankles in a relatively extended posture like modern humans and unlike chimpanzees. In other respects, however, trabecular properties in Au africanus are distinctive, with values that mostly fall between those of chimpanzees and humans. These results indicate that Au. africanus, like Homo, walked with an efficient, extended lower limb.

  6. Characterization of synthetic foam structures used to manufacture artificial vertebral trabecular bone.

    Science.gov (United States)

    Fürst, David; Senck, Sascha; Hollensteiner, Marianne; Esterer, Benjamin; Augat, Peter; Eckstein, Felix; Schrempf, Andreas

    2017-07-01

    Artificial materials reflecting the mechanical properties of human bone are essential for valid and reliable implant testing and design. They also are of great benefit for realistic simulation of surgical procedures. The objective of this study was therefore to characterize two groups of self-developed synthetic foam structures by static compressive testing and by microcomputed tomography. Two mineral fillers and varying amounts of a blowing agent were used to create different expansion behavior of the synthetic open-cell foams. The resulting compressive and morphometric properties thus differed within and also slightly between both groups. Apart from the structural anisotropy, the compressive and morphometric properties of the synthetic foam materials were shown to mirror the respective characteristics of human vertebral trabecular bone in good approximation. In conclusion, the artificial materials created can be used to manufacture valid synthetic bones for surgical training. Further, they provide novel possibilities for studying the relationship between trabecular bone microstructure and biomechanical properties. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Quantitative MR imaging for the in vivo assessment of trabecular bone quality

    Science.gov (United States)

    Toffanin, Renato; Strolka, Igor; Cova, Maria; Guglielmi, Giuseppe

    2005-08-01

    A major concern for space flight crews during long duration space mission is the effect of weightlessness on the skeletal system. In particular, bone loss has been noted in astronauts and cosmonauts exposed to microgravity from a few weeks to six months. Bone loss, which appears to increase in general proportion to mission length, may seriously enhance the risk of fracture during and after extended space flight. In past MIR and ISS missions, X-rays based techniques were used to assess pre- and post-flight cortical and trabecular bone mineral density (BMD). It has been shown, however, that BMD can explain only about 60% of the bone mechanical competence. Other methods are, therefore, required for the evaluation of bone quality. To this end, magnetic resonance imaging (MRI) has proved to be a promising technique, being able to provide information pertaining both to trabecular bone density and structure. The main purpose of this study was to assess the use of quantitative MRI of the calcaneus for the prediction of vertebral fractures. The results show that the effective transverse relaxation time (T2*) is sensitive to alterations in bone quality not capture by density. The potential application of MRI for the study of skeletal alterations in crewmembers after prolonged space mission is proposed.

  8. The Effect of Changing Scan Mode on Trabecular Bone Score Using Lunar Prodigy.

    Science.gov (United States)

    Chen, Weiwen; Slattery, Anthony; Center, Jacqueline; Pocock, Nicholas

    2016-10-01

    Trabecular bone score (TBS) is a measure of gray scale homogeneity that correlates with trabecular microarchitecture and is an independent predictor of fracture risk. TBS is being increasingly used in the assessment of patients at risk of osteoporosis and has recently been incorporated into FRAX ® . GE Lunar machines acquire spine scans using 1 of 3 acquisition modes depending on abdominal tissue thickness (thin, standard, and thick). From a database review, 30 patients (mean body mass index: 30.8, range 26.2-34.1) were identified who had undergone lumbar spine DXA scans (GE Lunar Prodigy, software 14.10; Lunar Radiation Corporation, Madison, WI) in both standard mode and thick mode, on the same day with no repositioning. Lumbar spine bone mineral density (L1-L4) and TBS were derived from the 30 paired spine scans. There was no significant difference in lumbar spine bone mineral density between the 2 scanning modes. There were, however, significant higher TBS values from the spine scans acquired in thick mode compared to the TBS values derived from spine acquisitions in standard mode (mean TBS difference: 0.24 [20%], standard deviation ±0.10). In conclusion, these preliminary data suggest that TBS values acquired in the GE Lunar Prodigy are dependent on the scanning mode used. Further evaluation is required to confirm the cause and develop appropriate protocols. Copyright © 2016 International Society for Clinical Densitometry. Published by Elsevier Inc. All rights reserved.

  9. Assessment of trabecular bone changes around endosseous implants using image analysis techniques: A preliminary study

    Energy Technology Data Exchange (ETDEWEB)

    Zuki, Mervet El [Dept. of Oral Medicine and Radiology, Benghazi University College of Dentistry, Benghazi (Libya); Omami, Galal [Oral Diagnosis and Polyclinics, Faculty of Dentistry, The University of Hong Kong (Hong Kong); Horner, Keith [Dept. of Oral Radiology, University Dental Hospital of Manchester, Manchester (United Kingdom)

    2014-06-15

    The objective of this study was to assess the trabecular bone changes that occurred around functional endosseous dental implants by means of radiographic image analysis techniques. Immediate preoperative and postoperative periapical radiographs of de-identified implant patients at the University Dental Hospital of Manchester were retrieved, screened for specific inclusion criteria, digitized, and quantified for structural elements of the trabecular bone around the endosseous implants, by using image analysis techniques. Data were analyzed using SPSS version 11.5. P values of less than 0.05 were considered statistically significant. A total of 12 implants from 11 patients were selected for the study, and 26 regions of interest were obtained. There was a significant increase in the bone area in terms of the mean distance between nodes (p=0.006) and a significant decrease in the marrow area in terms of the bone area (p=0.006) and the length of marrow spaces (p=0.032). It appeared that the bone around the implant underwent remodeling that resulted in a net increase in bone after implant placement.

  10. Neocellularization and neovascularization of nanosized bioactive glass-coated decellularized trabecular bone scaffolds

    KAUST Repository

    Gerhardt, Lutz Christian

    2012-09-11

    In this study, the in vivo recellularization and neovascularization of nanosized bioactive glass (n-BG)-coated decellu-larized trabecular bone scaffolds were studied in a rat model and quantified using stereological analyses. Based on the highest amount of vascular endothelial growth factor (VEGF) secreted by human fibroblasts grown on n-BG coatings (0-1.245 mg/cm 2), decellularized trabecular bone samples (porosity: 43-81%) were coated with n-BG particles. Grown on n-BG particles at a coating density of 0.263 mg/cm2, human fibroblasts produced 4.3 times more VEGF than on uncoated controls. After 8 weeks of implantation in Sprague-Dawley rats, both uncoated and n-BG-coated samples were well infiltrated with newly formed tissue (47-48%) and blood vessels (3-4%). No significant differences were found in cellularization and vascularization between uncoated bone scaffolds and n-BG-coated scaffolds. This finding indicates that the decellularized bone itself may exhibit growth-promoting properties induced by the highly interconnected pore microarchitecture and/or proteins left behind on decellularized scaffolds. Even if we did not find proangiogenic effects in n-BG-coated bone scaffolds, a bioactive coating is considered to be beneficial to impart osteoinductive and osteoconductive properties to decellularized bone. n-BG-coated bone grafts have thus high clinical potential for the regeneration of complex tissue defects given their ability for recellularization and neovascularization. © 2012 Wiley Periodicals, Inc.

  11. Estimating the mechanical competence parameter of the trabecular bone: a neural network approach

    Directory of Open Access Journals (Sweden)

    Érica Regina Filletti

    Full Text Available Abstract Introduction The mechanical competence parameter (MCP of the trabecular bone is a parameter that merges the volume fraction, connectivity, tortuosity and Young modulus of elasticity, to provide a single measure of the trabecular bone structural quality. Methods As the MCP is estimated for 3D images and the Young modulus simulations are quite consuming, in this paper, an alternative approach to estimate the MCP based on artificial neural network (ANN is discussed considering as the training set a group of 23 in vitro vertebrae and 12 distal radius samples obtained by microcomputed tomography (μCT, and 83 in vivo distal radius magnetic resonance image samples (MRI. Results It is shown that the ANN was able to predict with very high accuracy the MCP for 29 new samples, being 6 vertebrae and 3 distal radius bones by μCT and 20 distal radius bone by MRI. Conclusion There is a strong correlation (R2 = 0.97 between both techniques and, despite the small number of testing samples, the Bland-Altman analysis shows that ANN is within the limits of agreement to estimate the MCP.

  12. Bonding strength of glass-ceramic trabecular-like coatings to ceramic substrates for prosthetic applications.

    Science.gov (United States)

    Chen, Qiang; Baino, Francesco; Pugno, Nicola M; Vitale-Brovarone, Chiara

    2013-04-01

    A new approach based on the concepts of quantized fracture mechanics (QFM) is presented and discussed in this paper to estimate the bonding strength of trabecular-like coatings, i.e. glass-ceramic scaffolds mimicking the architecture of cancellous bone, to ceramic substrates. The innovative application of glass-derived scaffolds as trabecular-like coatings is proposed in order to enhance the osteointegration of prosthetic ceramic devices. The scaffolds, prepared by polymeric sponge replication, are joined to alumina substrates by a dense glass-ceramic coating (interlayer) and the so-obtained 3-layer constructs are investigated from micro-structural, morphological and mechanical viewpoints. In particular, the fracture strengths of three different crack propagation modes, i.e. glass-derived scaffold fracture, interface delamination or mixed fracture, are predicted in agreement with those of experimental mechanical tests. The approach proposed in this work could have interesting applications towards an ever more rational design of bone tissue engineering biomaterials and coatings, in view of the optimization of their mechanical properties for making them actually suitable for clinical applications. Copyright © 2012 Elsevier B.V. All rights reserved.

  13. Implant design and its effects on osseointegration over time within cortical and trabecular bone.

    Science.gov (United States)

    Beutel, Bryan G; Danna, Natalie R; Granato, Rodrigo; Bonfante, Estevam A; Marin, Charles; Tovar, Nick; Suzuki, Marcelo; Coelho, Paulo G

    2016-08-01

    Healing chambers present at the interface between implant and bone have become a target for improving osseointegration. The objective of the present study was to compare osseointegration of several implant healing chamber configurations at early time points and regions of interest within bone using an in vivo animal femur model. Six implants, each with a different healing chamber configuration, were surgically implanted into each femur of six skeletally mature beagle dogs (n = 12 implants per dog, total n = 72). The implants were harvested at 3 and 5 weeks post-implantation, non-decalcified processed to slides, and underwent histomorphometry with measurement of bone-to-implant contact (BIC) and bone area fraction occupied (BAFO) within healing chambers at both cortical and trabecular bone sites. Microscopy demonstrated predominantly woven bone at 3 weeks and initial replacement of woven bone by lamellar bone by 5 weeks. BIC and BAFO were both significantly increased by 5 weeks (p < 0.001), and significantly higher in cortical than trabecular bone (p < 0.001). The trapezoidal healing chamber design demonstrated a higher BIC than other configurations. Overall, a strong temporal and region-specific dependence of implant osseointegration in femurs was noted. Moreover, the findings suggest that a trapezoidal healing chamber configuration may facilitate the best osseointegration. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 104B: 1091-1097, 2016. © 2015 Wiley Periodicals, Inc.

  14. Injuries among elite snowboarders (FIS Snowboard World Cup).

    Science.gov (United States)

    Torjussen, J; Bahr, R

    2006-03-01

    Although snowboarding is already established as an Olympic sport, it is still a developing sport, with new disciplines, more demanding snow installations, and spectacular tricks. A recent study on subjects at Norwegian national elite level showed that injury risk is high and that injuries among competitive snowboarders differ from those seen in recreational snowboarders, with fewer wrist injuries and more knee and back injuries. To describe the incidence and type of injuries among female and male snowboarders at international elite level. At the last race of the Fédération Internationale de Ski Snowboard World Cup, acute injuries resulting in missed participation and overuse injuries influencing performance, were recorded during a retrospective interview (91% response rate). The registration period was from April 2002 (end of season) until March 2003. Exposure was recorded as the number of runs in all disciplines, and the incidence was calculated as number of injuries per 1000 runs. The 258 athletes interviewed reported 3193 competition days (n = 46 879 runs) in all disciplines. In total, 135 acute injuries were recorded; 62 (46%) during competition in the official disciplines. Of the 135 acute injuries, the most common injury locations were knee (n = 24; 18%), shoulder (n = 18; 13%), back (n = 17; 13%), and wrist (n = 11; 8%). The overall incidence during competition was 1.3 (95% confidence interval 1.0 to 1.7) injuries per 1000 runs; 2.3 (0.9 to 3.8) for big air (n = 10), 1.9 (1.1 to 2.8) for halfpipe (n = 21), 2.1 (1.2 to 3.0) for snowboard cross (n = 20), 0.6 (0.2 to 1.0) for parallel giant slalom (n = 8), and 0.3 (0.0 to 0.7) for parallel slalom (n = 3). The severity of injuries was graded based on time loss (27% lost >21 days) and score on the Abbreviated Injury Scale (AIS) (38% AIS 1, 61% AIS 2 and 1% AIS 3). There were 122 overuse injuries, 38 (31%) of these to the knee. The injury risk for big air, snowboard cross, and halfpipe disciplines is high, while

  15. An overview of systematic reviews of clinical evidence for cupping therapy

    Directory of Open Access Journals (Sweden)

    Huijuan Cao

    2015-01-01

    Conclusions: Cupping therapy may be beneficial for pain-related conditions, acne, and facial paralysis. However, a firm conclusion could not be drawn due to the insufficient number of included reviews and the low quality of the original studies.

  16. Cupping therapy: A prudent remedy for a plethora of medical ailments.

    Science.gov (United States)

    Mehta, Piyush; Dhapte, Vividha

    2015-07-01

    Since ancient times, complementary and alternative medicine (CAM; bǔ chōng yǔ tì dài yī xué) have played an important role in human health and welfare. Many therapeutic approaches in healthcare outside the realm of conventional medicine persist in various parts of the world. There is considerable scientific and commercial potential in CAM, which needs to be explored precisely. Cupping therapy ( bá guàn liáo fǎ), one of the CAM, is practiced across the world. This therapy is believed to act by correcting imbalances in the internal bio field, such as by restoring the flow of "Qi (qì)". Cupping involves applying a heated cup to generate a partial vacuum that mobilizes the blood flow and promotes effective healing. This review outlines various tools and techniques of cupping therapy.

  17. The Sorption Behavior of Wood Studied by Means of an Improved Cup Method

    DEFF Research Database (Denmark)

    Eitelberger, Johannes; Svensson, Staffan

    2012-01-01

    inwards the cup. In contrast to the common cup method, the herein presented method uses a data logger for relative humidity and temperature placed inside the cup. The use of thin cross-cut specimens allows for explicit separation of the different processes occurring during transient moisture transport....... Mass changes were determined and relative humidity inside the cups was measured for eight specimens of Norway spruce with different specimen thicknesses. Relative humidity was increased in three uniform steps in the test chamber from 4.0 up to 76.5%. The results obtained with this special test setup...... indicate that the sorption process is different than assumed in previous publications. This emphasizes the need of improved modeling approaches....

  18. Forecasting a winner for Malaysian Cup 2013 using soccer simulation model

    Science.gov (United States)

    Yusof, Muhammad Mat; Fauzee, Mohd Soffian Omar; Latif, Rozita Abdul

    2014-07-01

    This paper investigates through soccer simulation the calculation of the probability for each team winning Malaysia Cup 2013. Our methodology used here is we predict the outcomes of individual matches and then we simulate the Malaysia Cup 2013 tournament 5000 times. As match outcomes are always a matter of uncertainty, statistical model, in particular a double Poisson model is used to predict the number of goals scored and conceded for each team. Maximum likelihood estimation is use to measure the attacking strength and defensive weakness for each team. Based on our simulation result, LionXII has a higher probability in becoming the winner, followed by Selangor, ATM, JDT and Kelantan. Meanwhile, T-Team, Negeri Sembilan and Felda United have lower probabilities to win Malaysia Cup 2013. In summary, we find that the probability for each team becominga winner is small, indicating that the level of competitive balance in Malaysia Cup 2013 is quite high.

  19. Mechanistic Based DEM Simulation of Particle Attrition in a Jet Cup

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Wei; DeCroix, David; Sun, Xin

    2014-02-01

    The attrition of particles is a major industrial concern in many fluidization systems as it can have undesired effects on the product quality and on the reliable operation of process equipment. Therefore, to accomodate the screening and selection of catalysts for a specific process in fluidized beds, risers, or cyclone applications, their attrition propensity is usually estimated through jet cup attrition testing, where the test material is subjected to high gas velocities in a jet cup. However, this method is far from perfect despite its popularity, largely due to its inconsistency in different testing set-ups. In order to better understand the jet cup testing results as well as their sensitivity to different operating conditions, a coupled computational fluid dynamic (CFD) - discrete element method (DEM) model has been developed in the current study to investigate the particle attrition in a jet cup and its dependence on various factors, e.g. jet velocity, initial particle size, particle density, and apparatus geometry.

  20. Novel Faraday cup for the simultaneous observation and measurement of ion-beam currents

    International Nuclear Information System (INIS)

    Wei, C.; Seidman, D.N.

    1977-01-01

    A novel Faraday cup is described which allows the simultaneous observation and measurement of ion-beam currents. The Faraday cup is constructed around a Galileo channel electron multiplier array (CEMA), which serves as the basis of an internal image intensification system (a gain of >10 4 ) for the observation of the ion beam; the CEMA also acts as a collector for the ion current which is measured by a Keithley 602 electrometer. The ion current is integrated by a simple and inexpensive dosimeter; the electronic circuit for the dosimeter is described. The application of the Faraday cup to the observation and measurement of a 30-keV Ar + ion beam is presented as an illustrative example. We have also employed this Faraday cup to observe and measure 30-keV Cr + , Mo + , or W + , and 18-keV Au + ion beams employed for the in situ irradiation of field-ion microscope specimens

  1. A survey of the bacterial diversity in the cup filler of dental chair units.

    Science.gov (United States)

    Silva, Vítor; Figueira, Vânia; Figueiral, Helena; Manaia, Célia M

    2011-07-01

    Water from the cup filler of dental chair units (CFDC) was observed to contain sphingomonads, environmental mycobacteria and methylobacteria, among other minor bacteria. Some of the bacteria detected are recognized opportunistic pathogens. Some of these, tended to persist over time.

  2. Studies on Cup Anemometer Performances Carried out at IDR/UPM Institute. Past and Present Research

    Directory of Open Access Journals (Sweden)

    Elena Roibas-Millan

    2017-11-01

    Full Text Available In the present work, the research derived from a wide experience on cup anemometer calibration works at IDR/UPM Institute (Instituto Universitario de Microgravedad “Ignacio Da Riva” is summarized. This research started in 2008, analyzing large series of calibrations, and is focused on two main aspects: (1 developing a procedure to predict the degradation level of these wind sensors when working on the field and (2 modeling cup anemometer performances. The wear and tear level of this sensor is evaluated studying the output signal and its main frequencies through Fourier analysis. The modeling of the cup anemometer performances is carried out analyzing first the cup aerodynamics. As a result of this process, carried out through several testing and analytical studies since 2010, a new analytical method has been developed. This methodology might represent an alternative to the classic approach used in the present standards of practice such as IEC 64000-12.

  3. Benefit of cup medialization in total hip arthroplasty is associated with femoral anatomy.

    Science.gov (United States)

    Terrier, Alexandre; Levrero Florencio, Francesc; Rüdiger, Hannes A

    2014-10-01

    Medialization of the cup with a respective increase in femoral offset has been proposed in THA to increase abductor moment arms. Insofar as there are potential disadvantages to cup medialization, it is important to ascertain whether the purported biomechanical benefits of cup medialization are large enough to warrant the downsides; to date, studies regarding this question have disagreed. The purpose of this study was to quantify the effect of cup medialization with a compensatory increase in femoral offset compared with anatomic reconstruction for patients undergoing THA. We tested the hypothesis that there is a (linear) correlation between preoperative anatomic parameters and muscle moment arm increase caused by cup medialization. Fifteen patients undergoing THA were selected, covering a typical range of preoperative femoral offsets. For each patient, a finite element model was built based on a preoperative CT scan. The model included the pelvis, femur, gluteus minimus, medius, and maximus. Two reconstructions were compared: (1) anatomic position of the acetabular center of rotation, and (2) cup medialization compensated by an increase in the femoral offset. Passive abduction-adduction and flexion-extension were simulated in the range of normal gait. Muscle moment arms were evaluated and correlated to preoperative femoral offset, acetabular offset, height of the greater trochanter (relative to femoral center of rotation), and femoral antetorsion angle. The increase of muscle moment arms caused by cup medialization varied among patients. Muscle moment arms increase by 10% to 85% of the amount of cup medialization for abduction-adduction and from -35% (decrease) to 50% for flexion-extension. The change in moment arm was inversely correlated (R(2) = 0.588, p = 0.001) to femoral antetorsion (anteversion), such that patients with less femoral antetorsion gained more in terms of hip muscle moments. No linear correlation was observed between changes in moment arm and

  4. Effects of Cupping Therapy in Amateur and Professional Athletes: Systematic Review of Randomized Controlled Trials.

    Science.gov (United States)

    Bridgett, Rhianna; Klose, Petra; Duffield, Rob; Mydock, Suni; Lauche, Romy

    2018-03-01

    Despite the recent re-emergence of the process of cupping by athletes, supporting evidence for its efficacy and safety remains scarce. This systematic review aims to summarize the evidence of clinical trials on cupping for athletes. SCOPUS, Cochrane Library, PubMed, AMED, and CNKI databases were searched from their inception to December 10, 2016. Randomized controlled trials on cupping therapy with no restriction regarding the technique, or cointerventions, were included, if they measured the effects of cupping compared with any other intervention on health and performance outcomes in professionals, semi-professionals, and leisure athletes. Data extraction and risk of bias assessment using the Cochrane Risk of Bias Tool were conducted independently by two pairs of reviewers. Eleven trials with n = 498 participants from China, the United States, Greece, Iran, and the United Arab Emirates were included, reporting effects on different populations, including soccer, football, and handball players, swimmers, gymnasts, and track and field athletes of both amateur and professional nature. Cupping was applied between 1 and 20 times, in daily or weekly intervals, alone or in combination with, for example, acupuncture. Outcomes varied greatly from symptom intensity, recovery measures, functional measures, serum markers, and experimental outcomes. Cupping was reported as beneficial for perceptions of pain and disability, increased range of motion, and reductions in creatine kinase when compared to mostly untreated control groups. The majority of trials had an unclear or high risk of bias. None of the studies reported safety. No explicit recommendation for or against the use of cupping for athletes can be made. More studies are necessary for conclusive judgment on the efficacy and safety of cupping in athletes.

  5. [YANG's pricking-cupping therapy for knee osteoarthritis: a multi-center randomized controlled trial].

    Science.gov (United States)

    Wang, Bo; Liu, Xiru; Hu, Zhihai; Sun, Aijun; Ma, Yanwen; Chen Yingying; Zhang, Xuzhi; Liu, Meiling; Wang, Yi; Wang, Shuoshuo; Zhang, Yunjia; Li, Yijing; Shen, Weidong

    2016-02-01

    To evaluate the clinical efficacy of YANG's pricking-cupping therapy for knee osteoar thritis (KOA). Methods This was a multi-center randomized parallel controlled trial. One hundred and seventy one patients with KOA were randomly allocated to a pricking-cupping group (89 cases) and a conventional acu puncture group (82 cases). Neixiyan (EX-LE 4), Dubi (ST 35) and ashi points were selected in the two groups. Patients in the pricking-cupping group were treated with YANG's pricking-cupping therapy; the seven-star needles were used to perform pricking at acupoints, then cupping was used until slight bleeding was observed. Patients in the conventional acupuncture group were treated with semi-standardized filiform needle therapy. The treatment was given for 4 weeks (from a minimum of 5 times to a maximum of 10 times). The follow-up visit was 4 weeks. The Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) and the visual analogue scale (VAS) were adopted for the efficacy assessments. The pain score, stiffness score, physical function score and total score of WOMAC were all reduced after 4-week treatment and during follow-up visit in the two groups (all P0. 05), each score and total score of WOMAC in the pricking-cupping group were lower than those in the conventional acupuncture group after 4-week treatment and during follow-up visit (Pcupping group were lower than those in the conventional acupuncture group after 4-week treatment and during follow-up visit (P cupping and conventional acupuncture therapy can both significantly improve knee joint pain and function in patients with KOA, which are relatively safe. The pricking cupping therapy is superior to conventional acupuncture with the identical selection of acupoints.

  6. The Football World Cup 1998: an analysis of related attendances to an accident and emergency department.

    Science.gov (United States)

    Mattick, A P

    1999-06-01

    Throughout the Football World Cup Finals of France 1998, patients attended our inner city Accident and Emergency department with a variety of conditions related to the event. Analysis was made on the total of 151 patients who attended with World Cup related presentations during this five-week period. The majority were young men involved in alcohol related trauma. The workload of the department was only substantially affected after one match, that of the opening game between Brazil and Scotland.

  7. Use of small volume cups in XRF analysis of treated wood retention

    Science.gov (United States)

    Rene Stelzer; Adam Taylor; Patricia Lebow

    2017-01-01

    Efforts are underway in the United States to improve the conformance of commercially-treated wood with the applicable retention standards. As part of an effort to devise a practical method for on-site assessment of within-charge retention variation, we investigated whether small-volume x-ray fluorescence (XRF) sample cups could be used with treated wood. A range of cup...

  8. Psychological factors of performance in ski jumping : a quantitative study of World Cup ski jumpers

    OpenAIRE

    Sklett, Vegard Haukø

    2017-01-01

    Purpose – The present study investigated the relationship between psychological factors (self-efficacy, flow, positive- and negative affect, worry) and ski jumping performance, as well as the influential functions these psychological factors have on ski jumping performance. Method – World Cup ski jumpers (N = 40) responded to four questionnaires in the middle of the World Cup season, reporting their subjective experience during a competitive setting. Social Cognitive Theory (SCT) (Bandura...

  9. Mini biased collimated faraday cups for measurement of intense pulsed ion beams

    International Nuclear Information System (INIS)

    He Xiaoping; Shi Lei; Zhang Jiasheng; Qiu Aici

    2000-01-01

    An analysis of principle of a biased Faraday cup for measuring ion beams density and the main reasons related to the measuring accuracy were presented. An array of mini biased collimated Faraday cups was manufactured for the measurement of ion beam density of a compact 200 keV high power ion beam source. In the experiments the maximum density of ion beam was in the center of the beam, and it was about 170 A/cm 2

  10. Our Everyday Cup of Coffee: The Chemistry behind Its Magic

    Science.gov (United States)

    Petracco, Marino

    2005-08-01

    Coffee beverages are so popular all over the world that there is hardly any need to describe them. But underlying this seemingly commonplace beverage there is a whole realm worth serious scientific study. The complexity of the raw seed matrix, made even more intricate when roasted, requires a deep understanding of its chemical nature. While coffee is not consumed for nutritional purposes, it is appreciated for its taste appeal along with its stimulating effects on mental and physical activity. The attention to quality is of paramount importance to both of these aspects to supply the customers with a pleasant and wholesome product. The chemical approach to the sensory sphere has seen the development of increasingly sophisticated analytical methods where the parts per billion of volatile aromas are not the ultimate frontier of detection limits. In spite of the progress of instrumental techniques, the cup-testing approach still remains the final assessment tool to obtain the approval for choosing the right plant and for conveying the product to the market. This is even truer when espresso, the fashionable type of coffee brewing methods, is considered.

  11. The transformation of the offensive system in Asobal Cup 2011

    Directory of Open Access Journals (Sweden)

    Alejandro Perira Ortega

    2012-11-01

    Full Text Available The aim of this study is to obtain information regarding time length, areas and distances of the attack end, specific positions from which the attack end can be executed and differences in effectiveness between system 3:3 with two pivots and system 2:4. Therefore three matches of the Asobal Cup 2011 have been analyzed. This analysis leads us to obtain time values, distribution of absolute and relative frequencies, and to calculate the effectiveness coefficients: absolute success (EA, relative success (ER, absolute failure (FA and relative failure (FR. There were no differences between average length of extreme and first line deployment circulation. Systems 3:3 with two pivots provide more options for the attack end than the System 2:4 for the first line of attack. Furthermore, with the players going to the second line, pivots get a higher attack end percentage, between six and nine meters. System 3:3 with two pivots shows a better ER and FA value than system 2:4Keywords: offensive system, transitions, effectiveness, areas, distance, attack end.

  12. NETWORK ANALYSIS OF PORTUGUESE TEAM ON FIFA WORLD CUP 2014

    Directory of Open Access Journals (Sweden)

    Rui Sousa Mendes,

    2015-05-01

    Full Text Available Match analysis has been using in football case to identify properties and patterns of teams (Sarmento et al., 2014. From the regular notational analysis until the most recent computational tactical metrics, a lot of different outcomes can be possible to extract from a single match (Clemente, Couceiro, Martins, & Mendes, 2015. In the specific case of football, the cooperation among team-members is one of the main factors that contribute for a better performance (Grund, 2012. Thus, to analyse such cooperation the Social Network Analysis have been used to identify how team-members are connected and if there are cooperation tendencies inside the team (Clemente et al., 2015. The prominent players have been also analysed in order to identify the central players in the team (Clemente, Couceiro, Martins, & Mendes, 2014.Objectives: Therefore, using the social network analysis approach the aim of this study was to analyse the centrality levels of Portuguese positional roles during the FIFA World Cup 2014 and to identify the prominent tactical positions that determined the moments with ball.

  13. Co-ordination of NDH and Cup proteins in CO2 uptake in cyanobacterium Synechocystis sp. PCC 6803.

    Science.gov (United States)

    Han, Xunling; Sun, Nan; Xu, Min; Mi, Hualing

    2017-06-01

    High and low affinity CO2-uptake systems containing CupA (NDH-1MS) and CupB (NDH-1MS'), respectively, have been identified in Synechocystis sp. PCC 6803, but it is yet unknown how the complexes function in CO2 uptake. In this work, we found that deletion of cupB significantly lowered the growth of cells, and deletion of both cupA and cupB seriously suppressed the growth below pH 7.0 even under 3% CO2. The rate of photosynthetic oxygen evolution was decreased slightly by deletion of cupA but significantly by deletion of cupB and more severely by deletion of both cupA and cupB, especially in response to changed pH conditions under 3% CO2. Furthermore, we found that assembly of CupB into NDH-1MS' was dependent on NdhD4 and NdhF4. NDH-1MS' was not affected in the NDH-1MS-degradation mutant and NDH-1MS was not affected in the NDH-1MS'-degradation mutants, indicating the existence of independent CO2-uptake systems under high CO2 conditions. The light-induced proton gradient across thylakoid membranes was significantly inhibited in ndhD-deletion mutants, suggesting that NdhDs functions in proton pumping. The carbonic anhydrase activity was suppressed partly in the cupA- or cupB-deletion mutant but severely in the mutant with both cupA and cupB deletion, indicating that CupA and CupB function in conversion of CO2 to HCO3-. In turn, deletion of cup genes lowered the transthylakoid membrane proton gradient and deletion of ndhDs decreased the CO2 hydration. Our results suggest that NDH-1M provides an alkaline region to activate Cup proteins involved in CO2 uptake. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology.

  14. THE REDUCTION OF CHOLESTEROL WITH CUPPING THERAPY ON CHOLESTEROL REDUCTION IN PATIENTS WITH HYPERCHOLESTEROLEMIA

    Directory of Open Access Journals (Sweden)

    Zahid Fikri

    2017-04-01

    Full Text Available Introduction: Hypercholesterolemia is a risk factor causes of death at younger ages. Hypercholesterolemia may increase the risk of atherosclerosis, coronary heart disease, pancreatitis (pancreas inflammation in organs, diabetes mellitus, thyroid disorders, liver disease and kidney disease. Many patients with hypercholesterolemia using cupping therapy. Cupping therapy is alternative treatment process of throwing dirty blood from the body through the skin surface. The objective of this study was to determine the effect of cupping therapy to decrease cholesterol levels in patients with hypercholesterolemia. Method: Design used in this study was quasy experimental design. The population is all patients with hypercholesterolemia in the health center plaza Gresik. The total sample is 18 respondents, taken according to inclusion criteria. Independent variable is the cupping therapy. The dependent variable was the decrease in cholesterol levels. Data were collected using a questionnaire and observation of cholesterol. Data were analyzed using independent t-test and paired t tests with signi fi cance level α < 0.05. Result: The results show that cholesterol levels in patients with hypercholesterolemia treated groups decreased majority. Independent statistical analysis using t-test showed p = 0.001 and with the Paired t-test p value = 0.003. Discussion: This result means that there are significant effects of cupping therapy on cholesterol reduction in patients with hypercholesterolemia aged 45 years and over. Further research needs to be done in control diet, lifestyle and daily activities for the success of cupping therapy.

  15. Burns induced by cupping therapy in a burn center in northeast china.

    Science.gov (United States)

    Jing-Chun, Zhao; Jia-Ao, Yu; Chun-Jing, Xian; Kai, Shi; Lai-Jin, Lu

    2014-07-01

    Cupping therapy as a curative skill has been developed and applied throughout history. Despite reports of adverse effects, this therapy is considered to be relatively safe with no systemic reviews documenting negative side effects. The aim of this study was to explore methods that avoid the adverse effects sometimes associated with this therapy. Clinical records of 14 outpatients and inpatients that visited the First Hospital of Jilin University (Changchun, China) for management of burn injuries caused by cupping therapy were retrospectively reviewed. Characteristics, history of injury, and treatment of each patient was collected and analyzed. Burn injury induced by cupping therapy was not uncommon. Most of the injuries were mild to moderate and cured by conservative methods without severe complications. The use of wet cupping was more prevalent among injured patients than dry cupping. Cupping therapy as an ancient alternative treatment is still popular with a large number of devoted practitioners. Although there is the potential for injury during the application of this therapy, this is mostly preventable. Standardized training for health care professionals and increased the awareness among the public about the proper methods to administer this therapy to avoid adverse effects is important.

  16. Evaluation of a menstrual cup to collect shed endometrium for in vitro studies.

    Science.gov (United States)

    Koks, C A; Dunselman, G A; de Goeij, A F; Arends, J W; Evers, J L

    1997-09-01

    To evaluate whether a menstrual cup is a suitable instrument to collect antegradely shed endometrium for in vitro studies. A prospective, descriptive, cell biological and immunohistochemical study. Tertiary care university medical center. Nine female volunteers with regular cycles. Menstrual effluent was collected with a menstrual cup. Experience with the menstrual cup was described. Cytospin specimens, frozen sections, and cultures were prepared from the obtained menstrual tissue. The acceptability of the menstrual cup. The presence and viability of endometrial tissue was evaluated using immunohistochemical staining and culture outcome. All women except one described the menstrual cup as acceptable. Menstrual effluent contained single cells, clumps of cells, and glandlike structures. After 5 days of culture, the endometrial tissue appeared to be viable. Immunohistochemistry showed positive staining for vimentin in most cytospin specimens, in all cryostat specimens, and in 10 of 17 cultures. Cytokeratin 18 stained most cytospin specimens, all cryostat specimens, and 10 of 17 cultures. Positive staining for BW495/36 was observed in most cytospin specimens, all cryostat specimens, and 11 of 17 cultures. A menstrual cup in an acceptable instrument to collect antegradely shed menstrual tissue. Menstruum contains viable endometrial tissue that can be used for in vitro studies of endometrium and endometriosis.

  17. Additively manufactured 3D porous Ti-6Al-4V constructs mimic trabecular bone structure and regulate osteoblast proliferation, differentiation and local factor production in a porosity and surface roughness dependent manner

    International Nuclear Information System (INIS)

    Cheng, Alice; Boyan, Barbara D; Humayun, Aiza; Cohen, David J; Schwartz, Zvi

    2014-01-01

    Additive manufacturing by laser sintering is able to produce high resolution metal constructs for orthopedic and dental implants. In this study, we used a human trabecular bone template to design and manufacture Ti-6Al-4V constructs with varying porosity via laser sintering. Characterization of constructs revealed interconnected porosities ranging from 15–70% with compressive moduli of 2579–3693 MPa. These constructs with macro porosity were further surface-treated to create a desirable multi-scale micro-/nano-roughness, which has been shown to enhance the osseointegration process. Osteoblasts (MG63 cells) exhibited high viability when grown on the constructs. Proliferation (DNA) and alkaline phosphatase specific activity, an early differentiation marker, decreased as porosity increased, while osteocalcin, a late differentiation marker, as well as osteoprotegerin, vascular endothelial growth factor and bone morphogenetic proteins 2 and 4 increased with increasing porosity. Three-dimensional (3D) constructs with the highest porosity and surface modification supported the greatest osteoblast differentiation and local factor production. These results indicate that additively manufactured 3D porous constructs mimicking human trabecular bone and produced with additional surface treatment can be customized for increased osteoblast response. Increased factors for osteoblast maturation and differentiation on high porosity constructs suggest the enhanced performance of these surfaces for increasing osseointegration in vivo. (paper)

  18. Grizzly bears (Ursus arctos horribilis) and black bears (Ursus americanus) prevent trabecular bone loss during disuse (hibernation).

    Science.gov (United States)

    McGee-Lawrence, Meghan E; Wojda, Samantha J; Barlow, Lindsay N; Drummer, Thomas D; Castillo, Alesha B; Kennedy, Oran; Condon, Keith W; Auger, Janene; Black, Hal L; Nelson, O Lynne; Robbins, Charles T; Donahue, Seth W

    2009-12-01

    Disuse typically causes an imbalance in bone formation and bone resorption, leading to losses of cortical and trabecular bone. In contrast, bears maintain balanced intracortical remodeling and prevent cortical bone loss during disuse (hibernation). Trabecular bone, however, is more detrimentally affected than cortical bone in other animal models of disuse. Here we investigated the effects of hibernation on bone remodeling, architectural properties, and mineral density of grizzly bear (Ursus arctos horribilis) and black bear (Ursus americanus) trabecular bone in several skeletal locations. There were no differences in bone volume fraction or tissue mineral density between hibernating and active bears or between pre- and post-hibernation bears in the ilium, distal femur, or calcaneus. Though indices of cellular activity level (mineral apposition rate, osteoid thickness) decreased, trabecular bone resorption and formation indices remained balanced in hibernating grizzly bears. These data suggest that bears prevent bone loss during disuse by maintaining a balance between bone formation and bone resorption, which consequently preserves bone structure and strength. Further investigation of bone metabolism in hibernating bears may lead to the translation of mechanisms preventing disuse-induced bone loss in bears into novel treatments for osteoporosis.

  19. Intrinsic material properties of trabecular bone by nanoindentation testing of biopsies taken from healthy women before and after menopause.

    Science.gov (United States)

    Polly, Benjamin J; Yuya, Philip A; Akhter, Mohammed P; Recker, Robert R; Turner, Joseph A

    2012-04-01

    Postmenopausal osteoporosis in women is characterized by an increase in bone fragility and risk of fracture. In addition to transmenopausal decline in three-dimensional trabecular bone architecture, changes in intrinsic material properties (local stiffness, damping, and hardness) may contribute to increased bone fragility. In this study, nanoindentation was used to quantify transmenopausal changes in the intrinsic properties of trabecular bone. Paired transilial biopsy specimens were used from a previously reported study in which bone biopsies were obtained from women prior to menopause (premenopausal, age 49.0 ± 1.9) and at 12 months past the last menstrual period (postmenopausal, age 54.6 ± 2.2). Elastic and viscoelastic material properties of the trabecular bone were measured using quasi-static and dynamic nanoindentation techniques, respectively. Paired Student's t tests (n = 15) were performed to assess the significance of the measured intrinsic properties. Trabecular bone microarchitecture is compromised in postmenopausal women, and although this loss is associated with a trend toward reduction in some intrinsic properties (storage modulus), we found no statistically significant changes in bone intrinsic properties between healthy pre- and postmenopausal biopsies in the quasi-static results and frequency-averaged dynamic results.

  20. Effect of Body Weight on Cefazolin and Vancomycin Trabecular Bone Concentrations in Patients Undergoing Total Joint Arthroplasty.

    Science.gov (United States)

    Sharareh, Behnam; Sutherland, Christina; Pourmand, Deeba; Molina, Nathan; Nicolau, David P; Schwarzkopf, Ran

    2016-02-01

    Effective use of prophylactic antibiotics decreases the incidence of surgical site infections (SSIs) after total joint arthroplasty (TJA). The purpose of this prospective study was to determine the viability of weight-based dosing protocols for cefazolin and vancomycin to determine if appropriate minimum inhibitory concentrations (MIC) are met. Trabecular bone was harvested from discarded bone samples from 34 patients undergoing total knee arthroplasty (TKA) and total hip arthroplasty (THA). The cefazolin and vancomycin concentrations were determined in the trabecular bone using high-performance liquid chromatography. No difference was noted in bone concentration with respect to patient weight for cefazolin. Regarding vancomycin, a substantial difference was noted in trabecular bone concentrations with respect to patient weight with lower body mass index (BMI) achieving greater concentrations. Using the current weight-based protocol of antibiotic prophylaxis, 84% and 87% of patients receiving vancomycin and cefazolin, respectively, achieved bone concentrations above the MIC. Our assessment of trabecular concentration of cefazolin during TJA did not show any differences with respect to patient weight. However, vancomycin concentrations did show a difference with respect to BMI but this may be the result of the specific weight-based dosing protocol of vancomycin. Whereas the majority of cases were able to achieve adequate antibiotic concentrations in bone, further studies may be required to determine if increasing the pre-operative dosage of antibiotics is mandated given the findings of this pilot study.

  1. The classic: The architecture of the trabecular bone (tenth contribution on the mechanics of the human skeletal framework).

    Science.gov (United States)

    von Meyer, Georg Hermann

    2011-11-01

    Hermann von Meyer may rightfully be considered the original proposer of the concept of trabecular architecture following patterns suggesting the directions of principle compressive and tensile stresses in a similarly shaped trabecular structure. Until the mid 19th Century, few had observed trabecular architecture, and when depicted was generally considered to have little regularity. In the 1830s Bourgery, Ward, and Wyman independently described the regularity of trabecular architecture, but according to Koch (1917) the proposed explanations were in error or overly simplified. Karl Culmann, an engineer and the developer of "graphic statics," attended a lecture of von Meyer and made the connection, which was then developed by the latter in this seminal paper. We present the paper in translation here. The original German article entitled "Die Architectur der Spongiosa" was often written in long, cumbersome sentences, with sometimes obscure meanings. We have taken considerable license in translating, rearranging punctuation, and condensing the material into modern terminology and style, while attempting to maintain the flavor of von Meyer's writing. We thank Dr. Per K. Amundson for the original translation; Drs. John Skedros and Richard Brand made additional suggestions. An accompanying biographical sketch of Hermann von Meyer is available at DOI 10.1007/s11999-011-2040-6.

  2. Influence of object location in different FOVs on trabecular bone microstructure measurements of human mandible: a cone beam CT study

    NARCIS (Netherlands)

    Ibrahim, N.; Parsa, A.; Hassan, B.; van der Stelt, P.; Aartman, I.H.A.; Nambiar, P.

    2014-01-01

    The aim of this study was to assess the influence of different object locations in different fields of view (FOVs) of two cone beam CT (CBCT) systems on trabecular bone microstructure measurements of a human mandible. A block of dry human mandible was scanned at five different locations (centre,

  3. Edge loading in metal-on-metal hips: low clearance is a new risk factor.

    Science.gov (United States)

    Underwood, Richard J; Zografos, Angelos; Sayles, Ritchie S; Hart, Alister; Cann, Philippa

    2012-03-01

    The revision rate of large head metal-on-metal and resurfacing hips are significantly higher than conventional total hip replacements. The revision of these components has been linked to high wear caused by edge loading; which occurs when the head-cup contact patch extends over the cup rim. There are two current explanations for this; first, there is loss of entrainment of synovial fluid resulting in breakdown of the lubricating film and second, edge loading results in a large local increase in contact pressure and consequent film thickness reduction at the cup rim, which causes an increase in wear. This paper develops a method to calculate the distance between the joint reaction force vector and the cup rim--the contact patch centre to rim (CPCR) distance. However, the critical distance for the risk of edge loading is the distance from the contact patch edge to rim (CPER) distance. An analysis of explanted hip components, divided into edge worn and non-edge-worn components showed that there was no statistical difference in CPCR values, but the CPER value was significantly lower for edge worn hips. Low clearance hips, which have a more conformal contact, have a larger diameter contact patch and thus are more at risk of edge loading for similarly positioned hips.

  4. Differences in trabecular bone of leptin-deficient ob/ob mice in response to biomechanical loading.

    Science.gov (United States)

    Heep, Hansjoerg; Wedemeyer, Christian; Wegner, Alexander; Hofmeister, Sebastian; von Knoch, Marius

    2008-06-15

    It is known that bone mineral density (BMD) and the strength of bone is predicted by body mass. Fat mass is a significant predictor of bone mineral density which correlates with body weight. This suggests that body fat regulates bone metabolism first by means of hormonal factors and second that the effects of muscle and loading are signaling factors in mechanotransduction. Leptin, a peptide hormone produced predominantly by white fat cells, is one of these hormonal factors. The aim of this study was to investigate and measure by micro-CT the different effects of weight-bearing on trabecular bone formation in mice without the stimulation of leptin. Animals with an ad-libitum-diet (Group A) were found to increase body weight significantly at the age of six weeks in comparison with lean mice (Group B). From this point on, the difference increased constantly. At the age of twenty weeks the obese mice were almost twice as heavy as the lean mice. Significant statistical differences are shown between the two groups for body weight and bone mineral density. Examination of trabecular bone (BV/TV, trabecular number (Tb.N.), trabecular thickness (Tb.Th.)) revealed that the only statistically significant difference between the two groups was the Tb.N. for the proximal femur. High weight-bearing insignificantly improved all trabecular bone parameters in the obese mice. Compared with the control-diet Group B, the BV/TV and Tb.N. were slightly higher in the controlled-diet Group A, but not the Tb.Th.. However, correlation was found between Tb.N. and BMD on the one hand and body weight on the other hand. biomechanical loading led to decreased bone mineral density by a decrease in the number of trabeculae. Trabecular thickness was not increased by biomechanical loading in growing mice. Decreased body weight in leptin-deficient mice protects against bone loss. This finding is consistent with the principle of light-weight construction of bone. Differences in cortical and trabecular

  5. Radiological and migration results of the DURALOC(R)-cup after two years

    International Nuclear Information System (INIS)

    Juen, F.

    2000-10-01

    In 1997 a study was conduced concerning 69 consecutive patients, all of whom consisted of DURALOC(R) series 100 acetabular components. The clinical, radiological and migrational aspect of each component was investigated 2 and 4 years postoperatively. In addition to this, a further 92 cups were analyzed in an identical manner, again 2 years after implantation. This therefore equated to a total of 161 investigated cups after a follow up interval of 2 years. In 144 of these cases the cup was combined with a cementless hydroxyapatite coated Spotorno shaft, with the remaining 17 involving a cemented Link-shaft (Lubinus SP II). A 28 mm Biolox(R) ceramic head was constant in all cases. Clinical data for each cup was collected via completion of a standard examination form, while acetabular migration, both vertical and horizontal, was measured on serial radiographs by the computer assisted EBRA method. From analyses of collected data, it was clearly shown that the clinical results remained very good over the 2- and 4-year-periods however, from radiological evidence it was indicated that for the period 3-4 years postoperatively, an increasing amount of radiolucencies around the cups were apparent. There was clearly no correlation between clinical and migration results. From the data taken from 106 migration curves, the mean total migration over the initial two-year-period was calculated to be 0.88 mm. From analysis of a further 56 migration curves, the mean total migration within 4 years of implantation was assessed to be 1.23 mm, however a decreasing speed of migration over the final 2-year-period was indicated. Our results demonstrate that statements relating to migration results of particular cups are more accurate after four years. However, statements about mean migration values are possible after two years. A migration speed of 1 mm total migration within the first 2 years after operation was predictive for radiological loosening of the cup after four years (p=0

  6. Rekonstruksi pada Perforasi Palatum Akibat Pneggunaan Gigi Tiruan Lengkap Rahang Atas dengan Suction Cup

    Directory of Open Access Journals (Sweden)

    Cristiani Nadya Pramasari

    2012-12-01

    Full Text Available Latar belakang. Pemasangan suction cup pada gigi tiruan lengkap rahang atas merupakan salah satu cara untuk meningkatkan referensi. Kondisi vakum oleh karena suction cup ini dalam waktu jangka panjang dan tidak terkontrol mengakibatkan nekrosis jaringan yaitu adanya perforasi palatum. Tujuan. Melaporkan rekonstruksi penutupan perforasi palatum sebagai komplikasi penggunaan gigi tiruan lengkap rahang atas dengan suction cup. Laporan Kasus. Pada tanggal 11 September 2012 seorang pria berusia 64 tahun datang ke Poliklinik Bedah Mulut RSUP dr. Sardjito Yogyakarta dengan keluhan terdapat lubang pada langit-langit. Pasien menggunakan gigi palsu buatan tukang gigi dengan perekat berbahan karet pada langit-langit selama 5 tahun. Selama penggunaan gigi palsu pasien sering mengalami sakit dan pembengkakan di langit-langit sampai keluar nanah dan akhirnya terbentuk lubang sehingga jika minum air keluar dari hidung. Pemeriksaan rontgen oklusal rahang atas tampak adanya resorbsi regio palatum durum. Rekonstruksi menggunakan teknik push back modifikasi dilakukan untuk penutupan perforasi palatum di bawah anestesi umum. Kesimpulan. Suction cup pada gigi tiruan lengkap rahang atas mengakibatkan kerusakan jaringan lunak dan jaringan keras rongga mulut. Perforasi palatum yang diakibatkan oleh suction cup ini dapat dilakukan rekonstruksi dengan teknik push back dengan hasil yang cukup optimal.   Background. Suction cups are used to get retention of the complete dentures. The uncontrolled constant vacuum created by the suction cup induces necrosis of tissues and perforation ofpalate. Objective. To report reconstruction for palatal perforation closure as a complication due to prolonged use of maxillary denture with suction cup. Case Report. A 64 years old male patient came to the Department of Oral Surgery, Sardjito General Hospital Yogyakarta on September 11, 2012 with the complaint of hole in his palate. He was wearing dentures for the past 5 years. He also

  7. Sex-specific patterns in cortical and trabecular bone microstructure in the Kirsten Skeletal Collection, South Africa.

    Science.gov (United States)

    Beresheim, Amy C; Pfeiffer, Susan K; Grynpas, Marc D; Alblas, Amanda

    2018-02-07

    The purpose of this study was to provide bone histomorphometric reference data for South Africans of the Western Cape who likely dealt with health issues under the apartheid regime. The 206 adult individuals ( n female = 75, n male = 131, mean = 47.9 ± 15.8 years) from the Kirsten Skeletal Collection, U. Stellenbosch, lived in the Cape Town metropole from the late 1960s to the mid-1990s. To study age-related changes in cortical and trabecular bone microstructure, photomontages of mid-thoracic rib cross-sections were quantitatively examined. Variables include relative cortical area (Rt.Ct.Ar), osteon population density (OPD), osteon area (On.Ar), bone volume fraction (BV/TV), trabecular number (Tb.N), trabecular thickness (Tb.Th), and trabecular spacing (Tb.Sp). All cortical variables demonstrated significant relationships with age in both sexes, with women showing stronger overall age associations. Peak bone mass was compromised in some men, possibly reflecting poor nutritional quality and/or substance abuse issues throughout adolescence and early adulthood. In women, greater predicted decrements in On.Ar and Rt.Ct.Ar suggest a structural disadvantage with age, consistent with postmenopausal bone loss. Age-related patterns in trabecular bone microarchitecture are variable and difficult to explain. Except for Tb.Th, there are no statistically significant relationships with age in women. Men demonstrate significant negative correlations between BV/TV, Tb.N, and age, and a significant positive correlation between Tb.Sp and age. This research highlights sex-specific differences in patterns of age-related bone loss, and provides context for discussion of contemporary South African bone health. While the study sample demonstrates indicators of poor bone quality, osteoporosis research continues to be under-prioritized in South Africa. © 2018 Wiley Periodicals, Inc.

  8. [Reproducibility and accuracy in the morphometric and mechanical quantification of trabecular bone from 3 Tesla magnetic resonance images].

    Science.gov (United States)

    Alberich-Bayarri, A; Martí-Bonmatí, L; Sanz-Requena, R; Sánchez-González, J; Hervás Briz, V; García-Martí, G; Pérez, M Á

    2014-01-01

    We used an animal model to analyze the reproducibility and accuracy of certain biomarkers of bone image quality in comparison to a gold standard of computed microtomography (μCT). We used magnetic resonance (MR) imaging and μCT to study the metaphyses of 5 sheep tibiae. The MR images (3 Teslas) were acquired with a T1-weighted gradient echo sequence and an isotropic spatial resolution of 180μm. The μCT images were acquired using a scanner with a spatial resolution of 7.5μm isotropic voxels. In the preparation of the images, we applied equalization, interpolation, and thresholding algorithms. In the quantitative analysis, we calculated the percentage of bone volume (BV/TV), the trabecular thickness (Tb.Th), the trabecular separation (Tb.Sp), the trabecular index (Tb.N), the 2D fractal dimension (D(2D)), the 3D fractal dimension (D(3D)), and the elastic module in the three spatial directions (Ex, Ey and Ez). The morphometric and mechanical quantification of trabecular bone by MR was very reproducible, with percentages of variation below 9% for all the parameters. Its accuracy compared to the gold standard (μCT) was high, with errors less than 15% for BV/TV, D(2D), D(3D), and E(app)x, E(app)y and E(app)z. Our experimental results in animals confirm that the parameters of BV/TV, D(2D), D(3D), and E(app)x, E(app)y and E(app)z obtained by MR have excellent reproducibility and accuracy and can be used as imaging biomarkers for the quality of trabecular bone. Copyright © 2013 SERAM. Published by Elsevier Espana. All rights reserved.

  9. Preliminary result on trabecular bone score (TBS in lumbar vertebrae with experimentally altered microarchitecture

    Directory of Open Access Journals (Sweden)

    M. Di Stefano

    2013-01-01

    Full Text Available The aim of this preliminary research is to investigate the reliability of a new qualitative parameter, called Trabecular Bone Score (TBS, recently proposed for evaluating the microarchitectural arrangement of cancellous bone in scans carried out by dual energy X-ray absorptiometry (DXA. Vertebral bodies of 15 fresh samples of lumbar spines of adult pig were analysed either in basal conditions and with altered microarchitecture of the cancellous bone obtained by progressive drilling. The examined bony areas do not show changes in bone mineral density (BMD, whereas TBS values decrease with the increasing alteration of the vertebral microtrabecular structure. Our preliminary data seem to confirm the reliability of TBS as a qualitative parameter useful for evaluating the microarchitectural strength in bony areas quantitatively analysed by DXA.

  10. Mechanical and morphological properties of trabecular bone samples obtained from third metacarpal bones of cadavers of horses with a bone fragility syndrome and horses unaffected by that syndrome.

    Science.gov (United States)

    Symons, Jennifer E; Entwistle, Rachel C; Arens, Amanda M; Garcia, Tanya C; Christiansen, Blaine A; Fyhrie, David P; Stover, Susan M

    2012-11-01

    To determine morphological and mechanical properties of trabecular bone of horses with a bone fragility syndrome (BFS; including silicate-associated osteoporosis). Cylindrical trabecular bone samples from the distal aspects of cadaveric third metacarpal bones of 39 horses (19 horses with a BFS [BFS bone samples] and 20 horses without a BFS [control bone samples]). Bone samples were imaged via micro-CT for determination of bone volume fraction; apparent and mean mineralized bone densities; and trabecular number, thickness, and separation. Bone samples were compressed to failure for determination of apparent elastic modulus and stresses, strains, and strain energy densities for yield, ultimate, and failure loads. Effects of BFS and age of horses on variables were determined. BFS bone samples had 25% lower bone volume fraction, 28% lower apparent density, 18% lower trabecular number and thickness, and 16% greater trabecular separation versus control bone samples. The BFS bone samples had 22% lower apparent modulus and 32% to 33% lower stresses, 10% to 18% lower strains, and 41 % to 52% lower strain energy densities at yield, ultimate, and failure loads, compared with control bone samples. Differences between groups of bone samples were not detected for mean mineral density and trabecular anisotropy. Results suggested that horses with a BFS had osteopenia and compromised trabecular bone function, consistent with bone deformation and pathological fractures that develop in affected horses. Effects of this BFS may be systemic, and bones other than those that are clinically affected had changes in morphological and mechanical properties.

  11. Site-specific variability in trabecular bone dosimetry: Considerations of energy loss to cortical bone

    International Nuclear Information System (INIS)

    Patton, P.W.; Rajon, D.A.; Shah, A.P.; Jokisch, D.W.; Inglis, B.A.; Bolch, W.E.

    2002-01-01

    With continual advances in radionuclide therapies, increasing emphasis is being placed on improving the patient specificity of dose estimates to marrow tissues. While much work has been focused on determining patient-specific assessments of radionuclide uptake in the skeleton, few studies have been initiated to explore the individual variability of absorbed fraction data for electron and beta-particle sources in various skeletal sites. The most recent values of radionuclide S values used in clinical medicine continue to utilize a formalism in which electrons are transported under a trabecular bone geometry of infinite extent. No provisions are thus made for the fraction of energy lost to the cortical bone cortex of the skeletal site and its surrounding tissues. In the present study, NMR microscopy was performed on trabecular bone samples taken from the femoral head and humeral proximal epiphysis of three subjects: a 51-year male, an 82-year female, and an 86-year female. Following image segmentation and coupling to EGS4, electrons were transported within macrostructural models of the various skeletal sites that explicitly include the spatial extent of the spongiosa, as well as the thickness of the surrounding cortical bone. These energy-dependent profiles of absorbed fractions to marrow tissues were then compared to transport simulations made within an infinite region of spongiosa. Ratios of mean absorbed fraction, as weighted by the beta energy spectra, under both transport methodologies were then assembled for the radionuclides 32 P and 90 Y. These ratios indicate that corrections to existing radionuclide S values for 32 P can vary by as much as 5% for the male, 6% for the 82-year female, and 8% for the 86-year female. For the higher-energy beta spectrum of 90 Y, these same corrections can reach 8%, 10%, and 11%, respectively

  12. Bone mineral density and trabecular bone tissue quality in obese men

    Directory of Open Access Journals (Sweden)

    V.V. Povoroznyuk

    2017-02-01

    Full Text Available Obesity and osteoporosis are the two metabolic dise­ases with increased prevalence over last decades and a strong impact on the global morbidity and mortality have gained a status of major health threats worldwide. There is evidence that the higher body mass index (BMI values are associated with greater bone mineral density (BMD resulting in a site-specific protective effect for fragility fractures. On the other hand, higher BMI values increases incidence of falls and is associated with worse fractures consolidation. However, trabecular bone score (TBS indirectly explores bone quali­ty, independently of BMD. The aim of the study was to determine the connection between the BMD and TBS parameters in Ukrainian men suffering from obesity. Methods. We examined 396 men aged 40–89 years, by the BMI all the subjects were divided into 2 groups: Group A — with obesity and BMI ≥ 30 kg/m2 (n = 129 and Group B — without obesity and BMI < 30 kg/m2 (n = 267. The BMD of total body, lumbar spine at the site L1–L4, femur and forearm were measured by DXA (Prodigy, GEHC Lunar, Madison, WI, USA. The TBS of L1–L4 was assessed by means of TBS iNsight (Med-Imaps, Pessac, France. Results. In general, obese men had a significantly higher BMD of lumbar spine, femoral neck, total body and ultradistal forearm (p < 0.001 in comparison with men without obesity. The TBS of L1–L4 was significantly lower in obese men compared to non-obese men (p < 0.001. The significant positive correlation between the fat mass and the BMD at different sites was observed. The correlation between the fat mass and TBS of L1–L4 was also significant, but negative. Conclusions. Obesity negatively affects the quality of trabecular bone, while bone mineral density was significantly higher.

  13. Characterization of micro-invasive trabecular bypass stents by ex vivo perfusion and computational flow modeling

    Directory of Open Access Journals (Sweden)

    Hunter KS

    2014-03-01

    Full Text Available Kendall S Hunter,1 Todd Fjield,2 Hal Heitzmann,2 Robin Shandas,1 Malik Y Kahook3 1Department of Bioengineering, University of Colorado Denver, Aurora, CO, USA; 2Glaukos Corporation, Laguna Hills, CA, USA; 3University of Colorado Hospital Eye Center, Aurora, CO, USA Abstract: Micro-invasive glaucoma surgery with the Glaukos iStent® or iStent inject® (Glaukos Corporation, Laguna Hills, CA, USA is intended to create a bypass through the trabecular meshwork to Schlemm's canal to improve aqueous outflow through the natural physiologic pathway. While the iStent devices have been evaluated in ex vivo anterior segment models, they have not previously been evaluated in whole eye perfusion models nor characterized by computational fluid dynamics. Intraocular pressure (IOP reduction with the iStent was evaluated in an ex vivo whole human eye perfusion model. Numerical modeling, including computational fluid dynamics, was used to evaluate the flow through the stents over physiologically relevant boundary conditions. In the ex vivo model, a single iStent reduced IOP by 6.0 mmHg from baseline, and addition of a second iStent further lowered IOP by 2.9 mmHg, for a total IOP reduction of 8.9 mmHg. Computational modeling showed that simulated flow through the iStent or iStent inject is smooth and laminar at physiological flow rates. Each stent was computed to have a negligible flow resistance consistent with an expected significant decrease in IOP. The present perfusion results agree with prior clinical and laboratory studies to show that both iStent and iStent inject therapies are potentially titratable, providing clinicians with the opportunity to achieve lower target IOPs by implanting additional stents. Keywords: glaucoma, iStent, trabecular bypass, intraocular pressure, ab-interno, CFD

  14. Microstructural properties of trabecular bone autografts: comparison of men and women with and without osteoporosis.

    Science.gov (United States)

    Xie, Fen; Zhou, Bin; Wang, Jian; Liu, Tang; Wu, Xiyu; Fang, Rui; Kang, Yijun; Dai, Ruchun

    2018-03-05

    The microstructure of autologous bone grafts from men over 50 years old and postmenopausal women undergoing spinal fusion were evaluated using micro-CT. We demonstrated postmenopausal women, especially those with osteoporosis (OP) presented more serious microarchitectural deterioration of bone grafts. This study was undertaken to determine microstructural properties of cancellous bone used as autologous bone grafts from osteoporosis patients undergoing lumbar fusion by comparing microstructural indices to controls. Cancellous bone specimens from spinous processes were obtained from 41 postmenopausal women (osteoporosis women, n = 19; controls, n = 22) and 26 men over 50 years old (osteoporosis men, n = 8; controls, n = 18) during lumbar fusion surgery. The microstructural parameters were measured using micro-CT. Significant difference in bone volume fraction (BV/TV), specific bone surface (BS/BV), trabecular thickness (Tb.Th), and structure model index (SMI) value existed between postmenopausal women with OP and controls. Significant difference in trabecular number (Tb.N) existed between men over 50 years old with OP and controls. Postmenopausal women exhibited lower BV/TV, Tb.Th, and higher SMI value than men over 50 years old. Postmenopausal women with OP exhibited lower BV/TV, Tb.Th, and higher BS/BV than men over 50 years old with OP. Post-menopausal women and older men with OP have worse bone quality in autografts than non-osteoporotic men and women. Postmenopausal women with OP presented serious microarchitectural deterioration in older population.

  15. Propranolol Attenuates Risperidone-Induced Trabecular Bone Loss in Female Mice.

    Science.gov (United States)

    Motyl, Katherine J; DeMambro, Victoria E; Barlow, Deborah; Olshan, David; Nagano, Kenichi; Baron, Roland; Rosen, Clifford J; Houseknecht, Karen L

    2015-07-01

    Atypical antipsychotic (AA) drugs cause significant metabolic side effects, and clinical data are emerging that demonstrate increased fracture risk and bone loss after treatment with the AA, risperidone (RIS). The pharmacology underlying the adverse effects on bone is unknown. However, RIS action in the central nervous system could be responsible because the sympathetic nervous system (SNS) is known to uncouple bone remodeling. RIS treatment in mice significantly lowered trabecular bone volume fraction (bone volume/total volume), owing to increased osteoclast-mediated erosion and reduced osteoblast-mediated bone formation. Daytime energy expenditure was also increased and was temporally associated with the plasma concentration of RIS. Even a single dose of RIS transiently elevated expression of brown adipose tissue markers of SNS activity and thermogenesis, Pgc1a and Ucp1. Rankl, an osteoclast recruitment factor regulated by the SNS, was also increased 1 hour after a single dose of RIS. Thus, we inferred that bone loss from RIS was regulated, at least in part, by the SNS. To test this, we administered RIS or vehicle to mice that were also receiving the nonselective β-blocker propranolol. Strikingly, RIS did not cause any changes in trabecular bone volume/total volume, erosion, or formation while propranolol was present. Furthermore, β2-adrenergic receptor null (Adrb2(-/-)) mice were also protected from RIS-induced bone loss. This is the first report to demonstrate SNS-mediated bone loss from any AA. Because AA medications are widely prescribed, especially to young adults, clinical studies are needed to assess whether β-blockers will prevent bone loss in this vulnerable population.

  16. Usefulness of the Trabecular Bone Score for assessing the risk of osteoporotic fracture.

    Science.gov (United States)

    Redondo, L; Puigoriol, E; Rodríguez, J R; Peris, P; Kanterewicz, E

    2018-04-01

    The trabecular bone score (TBS) is an imaging technique that assesses the condition of the trabecular microarchitecture. Preliminary results suggest that TBS, along with the bone mineral density assessment, could improve the calculation of the osteoporotic fracture risk. The aim of this study was to analyse TBS values and their relationship with the clinical characteristics, bone mineral density and history of fractures of a cohort of posmenopausal women. We analysed 2,257 posmenopausal women from the FRODOS cohort, which was created to determine the risk factors for osteoporotic fracture through a clinical survey and bone densitometry with vertebral morphometry. TBS was applied to the densitometry images. TBS values ≤1230 were considered indicative of degraded microarchitecture. We performed a simple and multiple linear regression to determine the factors associated with this index. The mean TBS value in L1-L4 was 1.203±0.121. Some 55.3% of the women showed values indicating degraded microarchitecture. In the multiple linear regression analysis, the factors associated with low TBS values were age, weight, height, spinal T-score, glucocorticoid treatment, presence of type 2 diabetes and a history of fractures due to frailty. TBS showed microarchitecture degradation values in the participants of the FRODOS cohort and was associated with anthropometric factors, low bone mineral density values, the presence of fractures, a history of type 2 diabetes mellitus and the use of glucocorticoids. Copyright © 2017 Elsevier España, S.L.U. and Sociedad Española de Medicina Interna (SEMI). All rights reserved.

  17. Human mandibular trabecular bone density correlation with mechanical strength: implications for implant dentistry.

    Science.gov (United States)

    Kido, Hirofumi; Schulz, Eloy E; Kakura, Kae; Yamamoto, Katsuki; Morinaga, Kenzo; Matsuura, Masaro

    2011-08-01

    The prognosis of a dental implant depends on the mechanical properties of the bone. The preoperative diagnosis of bone quality has become more important, because the immediate loading procedure is now widely used, and a firm initial stability is required. Quantitative computed tomography (QCT) is an effective method of determining selectively the bone mineral density (BMD) of the trabecular bone mostly responsible for the survival of the implant. In this project, we investigated the relationship between the BMD measured by QCT and the mechanical strength of the mandible. The BMD (mg/mL) of 58 trabecular bone specimens from 6 embalmed human cadaver mandibles were obtained using QCT. The compressive strength to break point was performed with a mechanical device. Each specimen was washed and weighed. The mean values of BMD for the anterior, premolar, and molar region were 633.3, 571.0, and 518.3 mg/mL, respectively. The mean values of compressive strength were 0.237, 0.216, and 0.196 kN, and the ash weights were 0.047, 0.044, and 0.039 g, respectively. There was a positive correlation between the BMD and the mechanical strength (R = 0.77) and between the ash weight and the mechanical strength (R = 0.84). There was strong correlation of bone strength, bone mineral, and bone density by QCT. QCT is an excellent preoperative diagnostic tool to select the most mechanically appropriate implant for initial stability and improve the survival prognosis.

  18. Assessment of global morphological and topological changes in trabecular structure under the bone resorption process

    Science.gov (United States)

    Sidorenko, Irina N.; Bauer, Jan; Monetti, Roberto; Baum, Thomas; Rummeny, Ernst J.; Eckstein, Felix; Matsuura, Maiko; Lochmueller, Eva-Maria; Zysset, Philippe K.; Raeth, Christoph W.

    2012-03-01

    Osteoporosis is a frequent skeletal disease characterised both by loss of bone mineral mass and deterioration of cancellous bone micro-architecture. It can be caused by mechanical disuse, estrogen deficiency or natural age-related resorption process. Numerical analysis of high-resolution images of the trabecular network is recognised as a powerful tool for assessment of structural characteristics. Using μCT images of 73 thoracic and 78 lumbar human vertebral specimens in vitro with isotropic resolution of 26μm we simulate bone atrophy as random resorption of bone surface voxels. Global morphological and topological characteristics provided by four Minkowski Functionals (MF) are calculated for two numerical resorption models with and without conservation of global topological connectivity of the trabecular network, which simulates different types of bone loss in osteoporosis, as it has been described in males and females. Diagnostic performance of morphological and topological characteristics as a function of relative bone loss is evaluated by a correlation analysis with respect to experimentally measured Maximum Compressive Strength (MCS). In both resorption models the second MF, which coincides with bone surface fraction BS/TV, demonstrates almost constant value of Pearson's correlation coefficient with respect to the relative bone loss ▵BV/TV. This morphological characteristic does not vary considerably under age-related random resorption and can be used for predicting bone strength in the elderly. The third and fourth MF demonstrate an increasing correlation coefficients with MCS after applying random bone surface thinning without preserving topological connectivity, what can be used for improvement of evaluation of the current state of the structure.

  19. Effect of a novel load-bearing trabecular Nitinol scaffold on rabbit radius bone regeneration

    Energy Technology Data Exchange (ETDEWEB)

    Gotman, Irena, E-mail: gotman@technion.ac.il; Gutmanas, Elazar Y., E-mail: gutmanas@technion.ac.il [Department of Materials Science and Engineering, Techion-Israel Institute of Technology, Haifa, 32000 Israel (Israel); National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation); Zaretzky, Asaph [The Bruce Rappaport Faculty of Medicine, Technion-Israel Institute of Technology, Haifa, 31096 Israel (Israel); Psakhie, Sergey G. [National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation); Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation)

    2015-10-27

    The research aim was to evaluate the bone regeneration capability of novel load-bearing NiTi alloy (Nitinol) scaffolds in a critical-size defect (CSD) model. High strength “trabecular Nitinol” scaffolds were prepared by PIRAC (Powder Immersion Reaction Assisted Coating) annealing of the highly porous Ni foam in Ti powder at 900°C. This was followed by PIRAC nitriding to mitigate the release of potentially toxic Ni ions. Scaffolds phase composition and microstructure were characterized by X-ray diffraction and scanning electron microscopy (SEM/EDS), and their mechanical properties were tested in compression. New Zealand white rabbits received bone defect in right radius and were divided in four groups randomly. In the control group, nothing was placed in the defect. In other groups, NiTi scaffolds were implanted in the defect: (i) as produced, (ii) loaded with bone marrow aspirate (BMA), and (iii) biomimetically CaP-coated. The animals were sacrificed after 12 weeks. The forelimbs with scaffolds were resected, fixed, sectioned and examined in SEM. New bone formation inside the scaffold was studied by EDS analysis and by the processing of backscattered electron images. Bone ingrowth into the scaffold was observed in all implant groups, mostly next to the ulna. New bone formation was strongly enhanced by BMA loading and biomimeatic CaP coating, the bone penetrating as much as 1–1.5 mm into the scaffold. The results of this preliminary study demonstrate that the newly developed high strength trabecular Nitinol scaffolds can be successfully used for bone regeneration in critical size defects.

  20. Effect of a novel load-bearing trabecular Nitinol scaffold on rabbit radius bone regeneration

    Science.gov (United States)

    Gotman, Irena; Zaretzky, Asaph; Psakhie, Sergey G.; Gutmanas, Elazar Y.

    2015-10-01

    The research aim was to evaluate the bone regeneration capability of novel load-bearing NiTi alloy (Nitinol) scaffolds in a critical-size defect (CSD) model. High strength "trabecular Nitinol" scaffolds were prepared by PIRAC (Powder Immersion Reaction Assisted Coating) annealing of the highly porous Ni foam in Ti powder at 900°C. This was followed by PIRAC nitriding to mitigate the release of potentially toxic Ni ions. Scaffolds phase composition and microstructure were characterized by X-ray diffraction and scanning electron microscopy (SEM/EDS), and their mechanical properties were tested in compression. New Zealand white rabbits received bone defect in right radius and were divided in four groups randomly. In the control group, nothing was placed in the defect. In other groups, NiTi scaffolds were implanted in the defect: (i) as produced, (ii) loaded with bone marrow aspirate (BMA), and (iii) biomimetically CaP-coated. The animals were sacrificed after 12 weeks. The forelimbs with scaffolds were resected, fixed, sectioned and examined in SEM. New bone formation inside the scaffold was studied by EDS analysis and by the processing of backscattered electron images. Bone ingrowth into the scaffold was observed in all implant groups, mostly next to the ulna. New bone formation was strongly enhanced by BMA loading and biomimeatic CaP coating, the bone penetrating as much as 1-1.5 mm into the scaffold. The results of this preliminary study demonstrate that the newly developed high strength trabecular Nitinol scaffolds can be successfully used for bone regeneration in critical size defects.

  1. Significant and sustaining elevation of blood oxygen induced by Chinese cupping therapy as assessed by near-infrared spectroscopy.

    Science.gov (United States)

    Li, Ting; Li, Yaoxian; Lin, Yu; Li, Kai

    2017-01-01

    Cupping therapy has been used in traditional Chinese medicine for thousands of years to relieve muscle pain/tendency/fatigue and to cure or reduce symbols of other diseases. However, its therapeutic effect is sparsely interpreted in the language of modern physiology. To objectively evaluate its therapeutic effect, we focused on dry cupping treatment and utilized near-infrared spectroscopy (NIRS) to assess the concentration change in oxy-hemoglobin ([HbO 2 ]), deoxy-hemoglobin ([Hb]), and blood volume in the course of cupping therapy over 13 volunteers on the infraspinatus muscle, where is usually applied for shoulder pains. Both a prominent drop in [Hb] and a significant elevation in [HbO 2 ] in the tissue surrounding the cupping site were observed during both cupping and post-treatment, manifesting the enhancement of oxygen uptake. This resulting promotion indicates potential positive therapeutic effect of cupping therapy in hemodynamics for facilitating muscular functions.

  2. Total hip arthroplasty with cementless cup after acetabular fracture

    Directory of Open Access Journals (Sweden)

    Marcelo Alfonso Lugones

    2012-12-01

    Full Text Available Background Acetabular fractures are a common cause of degenerative hip arthritis. The incidence of post-traumatic osteoarthritis has been reported between 12% and 57% and avascular necrosis of the femoral head may occur in 2% to 40% after posterior fracture dislocation. The fracture is often caused by major trauma in road accidents, at work or during sports, and patients usually present for total hip replacement (THR at an earlier age than the general arthritic population. We describe and analyze our patients with uncemented acetabular reconstruction in post-traumatic arthritis and compare them with THR in non-traumatic arthritis. Methods We retrospectively evaluated 19 patients who underwent uncemented acetabular reconstruction due to post-traumatic arthritis secondary to acetabular fracture. Results The average age at the time of arthroplasty was 52.2 years (19-83. The age at the time of fracture was 47.9 years (16-81. The average time between the acetabular fracture and THR was 52.4 months (4-360. The average follow-up was 4.25 years. No acetabular component loosening or infections were seen in either group. The Harris Hip Score at an average follow-up of 4.25 years was 89.3 (57-99. The follow-up in the control group with non-traumatic arthritis was 4.9 years, and the Harris Hip Score was 94.1 points (78-100. There were no significant difference in the Harris Hip Score between groups (p = 0.24. Conclusion Uncemented acetabular reconstruction in post-traumatic arthritis secondary to acetabular fracture is a more difficult procedure than routine arthroplasty in patient with non-traumatic arthritis. In the short-term there are no clinical or radiographic differences in THR with uncemented acetabular cups in post-traumatic arthritis patients compared to patients with non-traumatic arthritis.

  3. Rugby World Cup 2015: World Rugby injury surveillance study.

    Science.gov (United States)

    Fuller, Colin W; Taylor, Aileen; Kemp, Simon P T; Raftery, Martin

    2017-01-01

    To determine the incidence, severity and nature of injuries sustained during the Rugby World Cup (RWC) 2015 together with the inciting events leading to the injuries. A prospective, whole population study. 639 international rugby players representing 20 countries. The study protocol followed the definitions and procedures recommended in the consensus statement for epidemiological studies in rugby union; output measures included players' age (years), stature (cm), body mass (kg) and playing position, and the group-level incidence (injuries/1000 player-hours), mean and median severity (days-absence), location (%), type (%) and inciting event (%) for match and training injuries. Incidence of injury was 90.1 match injuries/1000 player-match-hours (backs: 100.4; forwards: 81.1) and 1.0 training injuries/1000 player-training-hours (backs: 0.9; forwards: 1.2). The mean severity of injuries was 29.8 days-absence (backs: 30.4; forwards: 29.1) during matches and 14.4 days-absence (backs: 6.3; forwards: 19.8) during training. During matches, head/face (22.0%), knee (16.2%), muscle-strain (23.1%) and ligament-sprain (23.1%) and, during training, lower limb (80.0%) and muscle-strain (60.0%) injuries were the most common locations and types of injury. Being-tackled (24.7%) was the most common inciting event for injury during matches and rugby-skills-contact activities (70.0%) the most common during training. While the incidence, nature and inciting events associated with match injuries at RWC 2015 were similar to those reported previously for RWCs 2007 and 2011, there were increasing trends in the mean severity and total days-absence through injury. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  4. Standardized fluoroscopy-based technique to measure intraoperative cup anteversion.

    Science.gov (United States)

    Zingg, Matthieu; Boudabbous, Sana; Hannouche, Didier; Montet, Xavier; Boettner, Friedrich

    2017-10-01

    Direct anterior approach (DAA) with the patient lying supine has facilitated the use of intraoperative fluoroscopy and allows for standardized positioning of the patient. The current study presents a new technique to measure acetabular component anteversion using intraoperative fluoroscopy. The current paper describes a mathematical formula to calculate true acetabular component anteversion based on the acetabular component abduction angle and the c-arm tilt angle (CaT). The CaT is determined by tilting the c-arm until an external pelvic oblique radiograph with the equatorial plane of the acetabular component perpendicular to the fluoroscopy receptor is obtained. CaT is determined by direct reading on the C-arm device. The technique was validated using a radiopaque synbone model comparing the described technique to computed tomography anteversion measurement. The experiment was repeated 25 times. The difference in anteversion between the two measuring techniques was on average 0.2° (range -3.0-3.1). The linear regression coefficients evaluating the agreement between the experimental and control methods were 0.99 (95%CI 0.88-1.10, p < 0.001) and 0.33 (95%CI -1.53-2.20, p = 0.713) for the slope and intercept, respectively. The current study confirms that the described three-step c-arm acetabular cup measuring technique can reproducibly and reliably assess acetabular component anteversion in the supine position, as compared to CT-imaging. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:2307-2312, 2017. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

  5. The Use of Wet Cupping for Persistent Nonspecific Low Back Pain: Randomized Controlled Clinical Trial.

    Science.gov (United States)

    AlBedah, Abdullah; Khalil, Mohamed; Elolemy, Ahmed; Hussein, Asim A; AlQaed, Meshari; Al Mudaiheem, Abdullah; Abutalib, Raid A; Bazaid, Faisal Mohamed; Bafail, Ahmad Saeed; Essa, AboBakr; Bakrain, Mohammed Yahia

    2015-08-01

    To evaluate the effectiveness and safety of wet cupping therapy as a single treatment for persistent nonspecific low back pain (PNSLBP). Randomized controlled trial comparing wet cupping versus no treatment in PNSLBP. Outpatient clinic in three secondary care hospitals in Saudi Arabia. Eighty eligible participants with PNSLBP for at least 3 months were randomly allocated to an intervention group (n=40) or to a control group (n=40). Six wet cupping sessions within 2 weeks, each of which were done at two bladder meridian (BL) acupuncture points among BL23, BL24, and BL25. Only acetaminophen was allowed as a rescue treatment in both groups. The Numeric Rating Scale (NRS), McGill Present Pain Intensity (PPI), and Oswestry Disability Questionnaire (ODQ) were used as outcome measures. Numbers of acetaminophen tablets taken were compared at 4 weeks from baseline. Adverse events were recorded. At the end of the intervention, statistically significant differences in the three outcome measures favoring the wet cupping group compared with the control group were seen: NRS score, 29.2 (95% confidence interval [CI], 24.6-33.8) versus 57.9 (95% CI, 53.3-62.6), respectively; PPI score, 1.17 (95% CI, 0.96-1.4) versus 2.3 (95% CI, 2.1- 2.7); and ODQ score, 19.6 (95% CI, 16.5-22.7) versus 35.4 (95% CI, 32.3-38.5) (p=0.0001). This improvement continued for another 2 weeks after the end of the intervention. Acetaminophen was used less in the wet cupping group, but this difference was not statistically significant. No adverse events were reported. Wet cupping is potentially effective in reducing pain and improving disability associated with PNSLBP at least for 2 weeks after the end of the wet cupping period. Placebo-controlled trials are needed.

  6. Wet cupping therapy for treatment of herpes zoster: a systematic review of randomized controlled trials.

    Science.gov (United States)

    Cao, Huijuan; Zhu, Chenjun; Liu, Jianping

    2010-01-01

    Wet cupping is a traditional Chinese medicine therapy commonly used in treating herpes zoster in China, and clinical studies have shown that wet cupping may have beneficial effect on herpes zoster compared with Western medication. We included randomized controlled trials (RCTs) on wet cupping for herpes zoster. We searched PubMed, the Cochrane Library (Issue 3, 2008), China Network Knowledge Infrastructure (CNKI), Chinese Scientific Journals Fulltext Database VIP, and Wan Fang Database. All searches ended in February 2009. Two authors extracted data and assessed the trials' quality independently. RevMan 5.0.18 software (The Cochrane Collaboration, The Nordic Cochrane Centre, Copenhagen, Denmark) was used for data analysis with effect estimate presented as relative risk (RR) and mean difference (MD) with a 95% confidence interval (CI). Eight RCTs involving 651 patients were included, and the methodological quality of trials was generally fair in terms of randomization, blinding, and intention-to-treat analysis. Meta-analyses showed wet cupping was superior to medication in the number of cured patients (RR 2.49, 95% CI 1.91 to 3.24, P cupping plus medication was significantly better than medication alone on number of cured patients (RR 1.93, 95% CI 1.23 to 3.04, P = .005) but demonstrated no difference in symptom improvement (RR 1.00, 95% CI 0.92 to 1.08, P = .98). There were no serious adverse effects related to wet cupping therapy in the included trials. Wet cupping appears to be effective in the treatment of herpes zoster. However, further large, rigorously designed

  7. No increased risk of early revision during the implementation phase of new cup designs

    Science.gov (United States)

    Björk, Mathias; Nemes, Szilard; Rolfson, Ola; Jolbäck, Per; Kärrholm, Johan

    2016-01-01

    Background and purpose — In Sweden, less than 5% of patients who undergo total hip arthroplasty (THA) have revision. Younger patients have an increased risk of revision. New prosthetic designs are being introduced in order to improve outcomes further. We investigated whether the introductory phase of new cup designs would increase the revision rate. Patients and methods — All THAs and first-time cup revisions performed from 1993 through 2011 were identified in the Swedish Hip Arthroplasty Register. The 15 types of cups used in more than 500 operations and inserted in more than 50 cases in each hospital (n = 52,903) were selected. All cups were given an order number, based on the order in which the cup had been inserted at each hospital. The influence of order number on the risk of revision was analyzed in a regression model, which was adjusted for potentially confounding demographic and surgical data. Revision within 2 years for all reasons (n = 940) was used as primary endpoint. Changes in the risk of revision based on the order number were analyzed using a spline. Results — The order number of the cup had no influence on the risk of early revision (p ≥ 0.7). Categorizing the order number using cutoff values obtained from the splines did not result in any statistically significant changes in risk of revision (p ≥ 0.2). Interpretation — We did not find any increased risk of early revision during the implementation phase of new cup designs. This finding is unexpected, and partly conflicts with data from other registries. The structured and stepwise introduction of new prosthesis designs, facilitated by the annual feedback from the Swedish Hip Arthroplasty Register, may partly explain this discrepancy. PMID:27168095

  8. Relative merits of polystyrene foam and paper in hot drink cups: Implications for packaging

    Science.gov (United States)

    Hocking, Martin B.

    1991-11-01

    An analysis of the overall relative merits of the use of uncoated paper vs molded polystyrene bead foam in single-use 8-oz cups is described here as a manageable example of the use of paper vs plastics in packaging. In raw material requirements the paper cup required about 2.5 times its finished weight of raw wood and about the same hydrocarbon fueling requirement as is needed for the polystyrene foam cup. To process the raw materials about six times as much steam, 13 times as much electric power, and twice as much cooling water are consumed to produce the paper cup as compared to the polystyrene foam cup. Emission rates to air are similar and to water are generally higher for the paper cup. Virtually all primary use factors favor polystyrene foam over paper. Once used both cup types may be recycled. Landfill disposal of the two items under dry conditions will occupy similar landfill volumes after compaction and will confer similarly slow to nonexistent decomposition to either option. Under wet conditions polystyrene foam will not readily degrade, but may help other materials to do so. Paper under wet conditions will biodegrade to produce methane, a significant greenhouse gas, biochemical oxygen demand to any leachate, and instability to the land surface during the process. Both materials can be incinerated cleanly in a municipal waste stream with the option of energy recovery, to yield an ash volume of 2% 5% of the incoming waste volume. Overall this analysis would suggest that polystyrene foam, with an extension to plastics in general, should be given more evenhanded consideration relative to paper in packaging applications than is currently the case.

  9. Yeast CUP1 protects HeLa cells against copper-induced stress

    Energy Technology Data Exchange (ETDEWEB)

    Xie, X.X. [Department of Animal Sciences, School of Agriculture and Biology, Shanghai Jiao Tong University, Shanghai (China); Shanghai Key Laboratory of Veterinary Biotechnology, Shanghai (China); College of Biological and Environmental Engineering, Zhejiang University of Technology, Hangzhou (China); Ma, Y.F.; Wang, Q.S.; Chen, Z.L.; Liao, R.R.; Pan, Y.C. [Department of Animal Sciences, School of Agriculture and Biology, Shanghai Jiao Tong University, Shanghai (China); Shanghai Key Laboratory of Veterinary Biotechnology, Shanghai (China)

    2015-06-12

    As an essential trace element, copper can be toxic in mammalian cells when present in excess. Metallothioneins (MTs) are small, cysteine-rich proteins that avidly bind copper and thus play an important role in detoxification. YeastCUP1 is a member of the MT gene family. The aim of this study was to determine whether yeast CUP1 could bind copper effectively and protect cells against copper stress. In this study,CUP1 expression was determined by quantitative real-time PCR, and copper content was detected by inductively coupled plasma mass spectrometry. Production of intracellular reactive oxygen species (ROS) was evaluated using the 2',7'-dichlorofluorescein-diacetate (DCFH-DA) assay. Cellular viability was detected using the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay, and the cell cycle distribution of CUP1 was analyzed by fluorescence-activated cell sorting. The data indicated that overexpression of yeast CUP1 in HeLa cells played a protective role against copper-induced stress, leading to increased cellular viability (P<0.05) and decreased ROS production (P<0.05). It was also observed that overexpression of yeast CUP1 reduced the percentage of G1 cells and increased the percentage of S cells, which suggested that it contributed to cell viability. We found that overexpression of yeast CUP1 protected HeLa cells against copper stress. These results offer useful data to elucidate the mechanism of the MT gene on copper metabolism in mammalian cells.

  10. Preclinical, clinical, and over-the-counter postmarketing experience with a new vaginal cup: menstrual collection.

    Science.gov (United States)

    North, Barbara B; Oldham, Michael J

    2011-02-01

    Menstrual cups have been available for decades, but their use is limited by bulky design and the need for multiple sizes. The Softcup® (Instead, Inc., San Diego, CA) is a simple single-size disposable over-the-counter (OTC) menstrual cup that compresses to tampon shape to facilitate insertion and can be worn during coitus. This report describes preclinical evaluation, clinical testing, and postmarketing monitoring of the Softcup. Preclinical testing complied with U.S. Food and Drug Administration (FDA) guidelines and used standard United States Pharmacopoeia methodologies for assessment of potential toxicity. Clinical testing enrolled 406 women in seven U.S. centers. A detailed written questionnaire assessed safety, acceptability, and effectiveness for menstrual collection. Study safety parameters included pelvic examinations, Pap smears, colposcopy, urinalysis, vaginal pH, wet mounts, gram stain, and vaginal microflora cultures. Postmarketing surveillance of over 100 million Softcups has been conducted by the manufacturer and by the FDA Medwatch system. No toxicity or mutagenicity was observed in preclinical evaluations. In clinical testing, after three cycles of cup use, 37% of subjects rated the cup as better than, 29% as worse than, and 34% as equal to pads or tampons. The cup was preferred for comfort, dryness, and less odor. Cups received lower ratings for disposal and convenience. Eighty-one percent of enrolled women were able to insert and remove their first cup using only written instructions. Use difficulties resulting in study discontinuations included cramping (1%), leakage (1%), and improper fit (3%). No safety parameters were adversely affected. No significant health risks were reported during postmarketing surveillance. These results demonstrate that a single-size vaginal device has no significant health risks and is acceptable to many women without the need for fitting or other medical services.

  11. Cupping Therapy (Al-Hijamah): An Exploratory Study of Healthcare Professionals Controversial Beliefs and Conceptions, Kingdom of Saudi Arabia

    OpenAIRE

    Ahmed T. El-Olemy; Abdullah M. Al-Bedah; Ahmed H. Almosilhi; Jawaher A. Almusailhi; Asim A. Hussein; Mohamed Khalil; Tamer S. Aboushanab; Ibrahim M. Elsubai; Meshari S. Alqaed; Gazzaffi I. M. Ali; Sulaiman Al-Eidi; Naseem A. Qureshi

    2017-01-01

    Background: Cupping therapy (Al-Hijamah) is a traditional therapy, supported and practised by people around the world since ancient times. Cupping therapy related to complementary and alternative medicine is associated with controversial, false beliefs and misconceptions. Objective: This study aimed at exploring controversial beliefs and conceptions about cupping therapy among healthcare professionals, Riyadh, Kingdom of Saudi Arabia (KSA). Methods: A cross-sectional study involving 2...

  12. No association between the aluminium content of trabecular bone and bone density, mass or size of the proximal femur in elderly men and women

    Directory of Open Access Journals (Sweden)

    Mallmin Hans

    2006-08-01

    Full Text Available Abstract Background Aluminium is considered a bone toxic metal since poisoning can lead to aluminium-induced bone disease in patients with chronic renal failure. Healthy subjects with normal renal function retain 4% of the aluminium consumed. They might thus also accumulate aluminium and eventually be at risk of long-term low-grade aluminium intoxication that can affect bone health. Methods We therefore examined 62 patients with femoral neck fractures or osteoarthritis of the hip (age range 38–93, with the aim of examining whether aluminium in bone is associated with bone-mineral density (BMD, content (BMC or width of the femoral neck measured by dual-energy X-ray absorptiometry (DXA. During operations bone biopsies were taken from the trabecular bone of the proximal femur. The samples were measured for their content of aluminium using a mass spectrometer. Results No significant association between the aluminium content in bone and femoral neck BMD, BMC or width could be found after multivariate adjustment. Conclusion Our results indicate that the accumulated aluminium content in bone during life does not substantially influence the extent of osteoporosis.

  13. No association between the aluminium content of trabecular bone and bone density, mass or size of the proximal femur in elderly men and women.

    Science.gov (United States)

    Hellström, Hans-Olov; Mjöberg, Bengt; Mallmin, Hans; Michaëlsson, Karl

    2006-08-23

    Aluminium is considered a bone toxic metal since poisoning can lead to aluminium-induced bone disease in patients with chronic renal failure. Healthy subjects with normal renal function retain 4% of the aluminium consumed. They might thus also accumulate aluminium and eventually be at risk of long-term low-grade aluminium intoxication that can affect bone health. We therefore examined 62 patients with femoral neck fractures or osteoarthritis of the hip (age range 38-93), with the aim of examining whether aluminium in bone is associated with bone-mineral density (BMD), content (BMC) or width of the femoral neck measured by dual-energy X-ray absorptiometry (DXA). During operations bone biopsies were taken from the trabecular bone of the proximal femur. The samples were measured for their content of aluminium using a mass spectrometer. No significant association between the aluminium content in bone and femoral neck BMD, BMC or width could be found after multivariate adjustment. Our results indicate that the accumulated aluminium content in bone during life does not substantially influence the extent of osteoporosis.

  14. Mode of action of cupping--local metabolism and pain thresholds in neck pain patients and healthy subjects.

    Science.gov (United States)

    Emerich, M; Braeunig, M; Clement, H W; Lüdtke, R; Huber, R

    2014-02-01

    Cupping worldwide has been part of traditional medicine systems and is in the western world used as CAM therapy mainly for treating pain syndromes. The mode of action is up to now unclear. In order to investigate its mechanism we measured in parallel metabolic changes in the tissue under the cupping glass and pressure pain thresholds. In 12 volunteers (6 healthy subjects and 6 patients with chronic neck pain) a microdialysis system was implanted subcutaneously on both sides (left and right) above the trapezius muscle. After baseline measures cupping was performed at one randomly selected side (left or right), the other side served as control. Every 20 min during baseline measures and for 280 min after cupping, microdialysis probes for detection of lactate, pyruvate, glucose and glycerin were taken. In addition, pain thresholds were measured before and after cupping with algometry. Cupping resulted in a strong increase of lactate (beginning 160 min after cupping until the end of the measurements) and the lactate/pyruvate ratio, indicating an anaerobe metabolism in the surrounding tissue. Baseline pain thresholds were non-significantly lower in neck pain patients compared to healthy controls and slightly increased immediately after cupping (ppain patients). After 280 min no more significant changes of pain thresholds were detected. Cupping induces >280 min lasting anaerobe metabolism in the subcutaneous tissue and increases immediate pressure pain thresholds in some areas. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. Multipurpose sampler device for liquid metal

    International Nuclear Information System (INIS)

    Nelson, P.A.; Kolba, V.M.; Holmes, J.T.

    1975-01-01

    A device for collecting samples or examining a flow of liquid metal is provided for use with such as a liquid-metal-cooled nuclear reactor. The sampler device includes a casing surrounded by an external heater for establishing an upper isothermal zone and a lower zone for heating the entering liquid metal. One of various inserts is suspended into the isothermal zone where it is surrounded by a shroud tube for directing liquid-metal flow from the heating zone into the top of the insert. Discharge flow from the insert gravitates through a helically wound tube in heat exchange contact with entering liquid-metal flow within the heating zone. The inserts comprise an overflow cup with upper and lower freeze seals, a filter for removing particulate matter, and a fixture for maintaining various sample materials in equilibrium with liquid-metal flow. (U.S.)

  16. Cupping for chronic nonspecific neck pain: a 2-year follow-up.

    Science.gov (United States)

    Lauche, Romy; Cramer, Holger; Langhorst, Jost; Dobos, Gustav

    2013-01-01

    Several trials have shown that cupping might be an effective treatment for chronic nonspecific neck pain, but little is known about the long-term effectiveness. This study aimed to investigate long-term effects of a short series of cupping; therefore additional follow-up measurements were conducted 2 years after completion of 3 studies. Participants from 3 randomized waitlist controlled trials on cupping for chronic nonspecific neck pain were followed 2 years after treatment. Outcome measures included neck pain intensity (100 mm Visual Analog Scale; VAS), functional disability (Neck Disability Index, NDI), and health-related quality of life (Short Form 36 Health Survey Questionnaire; SF-36). 133 of 150 patients had received cupping treatment and were contacted; 82 of them (61.7%) returned the follow-up questionnaires. No effect was found for neck pain intensity, but for physical function (∆ NDI: -3.15; 95% CI: -5.89; -0.41; p = 0.025) and quality of life (∆ physical component summary: 2.97; 95% CI: 0.97; 4.97; p = 0.004; ∆ bodily pain: 14.53; 95 % CI: 9.67; 19.39; p cupping effect was 8.9 ± 8.7 months with 16 patients reporting that neck pain had not yet reached the level before cupping. The majority of the patients did not continue cupping therapy, mostly due to lack of providers, costs or loss of interest. A series of cupping treatments did not influence neck pain intensity on the longer term, however significant increases were found for physical function and quality of life in patients with chronic nonspecific neck pain. Due to the considerable drop-out rate conclusions are limited. There is evidence suggesting that cupping treatment might have sustainable effects in some patients. Further randomized controlled trials with long-term follow-up are urgently needed for conclusive judgment of long-term effectiveness. © 2013 S. Karger GmbH, Freiburg.

  17. Metal-on-Metal Hip Resurfacing Arthroplasty

    Science.gov (United States)

    Sehatzadeh, S; Kaulback, K; Levin, L

    2012-01-01

    Background Metal-on-metal (MOM) hip resurfacing arthroplasty (HRA) is in clinical use as an appropriate alternative to total hip arthroplasty in young patients. In this technique, a metal cap is placed on the femoral head to cover the damaged surface of the bone and a metal cup is placed in the acetabulum. Objectives The primary objective of this analysis was to compare the revision rates of MOM HRA using different implants with the benchmark set by the National Institute of Clinical Excellence (NICE). The secondary objective of this analysis was to review the literature regarding adverse biological effects associated with implant material. Review Methods A literature search was performed on February 13, 2012, to identify studies published from January 1, 2009, to February 13, 2012. Results The revision rates for MOM HRA using 6 different implants were reviewed. The revision rates for MOM HRA with 3 implants met the NICE criteria, i.e., a revision rate of 10% or less at 10 years. Two implants had short-term follow-ups and MOM HRA with one of the implants failed to meet the NICE criteria. Adverse tissue reactions resulting in failure of the implants have been reported by several studies. With a better understanding of the factors that influence the wear rate of the implants, adverse tissue reactions and subsequent implant failure can be minimized. Many authors have suggested that patient selection and surgical technique affect the wear rate and the risk of tissue reactions. The biological effects of high metal ion levels in the blood and urine of patients with MOM HRA implants are not known. Studies have shown an increase in chromosomal aberrations in patients with MOM articulations, but the clinical implications and long-term consequences of this increase are still unknown. Epidemiological studies have shown that patients with MOM HRA implants did not have an overall increase in mortality or risk of cancer. There is insufficient clinical data to confirm the

  18. Testing methods of pressure distribution of bra cups on breasts soft tissue

    Science.gov (United States)

    Musilova, B.; Nemcokova, R.; Svoboda, M.

    2017-10-01

    Objective of this study is to evaluate testing methods of pressure distribution of bra cups on breasts soft tissue, the system which do not affect the space between the wearer's body surface and bra cups and thus do not influence the geometry of the measured body surface and thus investigate the functional performance of brassieres. Two measuring systems were used for the pressure comfort evaluating: 1) The pressure distribution of a wearing bra during 20 minutes on women's breasts has been directly measured using pressure sensor, a dielectricum which is elastic polyurethane foam bra cups. Twelve points were measured in bra cups. 2) Simultaneously the change of temperature in the same points bra was tested with the help of noncontact system the thermal imager. The results indicate that both of those systems can identify different pressure distribution at different points. The same size of bra designing features bra cups made from the same material and which is define by the help of same standardised body dimensions (bust and underbust) can cause different value of a compression on different shape of a woman´s breast soft tissue.

  19. Modeling of Flexible Polyurethane Foam Shrinkage for Bra Cup Moulding Process Control

    Directory of Open Access Journals (Sweden)

    Long Wu

    2018-04-01

    Full Text Available Nowadays, moulding technology has become a remarkable manufacturing process in the intimate apparel industry. Polyurethane (PU foam sheets are used to mould three-dimensional (3D seamless bra cups of various softness and shapes, which eliminate bulky seams and reduce production costs. However, it has been challenging to accurately and effectively control the moulding process and bra cup thickness. In this study, the theoretical mechanism of heat transfer and the thermal conductivity of PU foams are first examined. Experimental studies are carried out to investigate the changes in foam materials at various moulding conditions (viz., temperatures, and lengths of dwell time in terms of surface morphology and thickness by using electron and optical microscopy. Based on the theoretical and experimental investigations of the thermal conductivity of the foam materials, empirical equations of shrinkage ratio and thermal conduction of foam materials were established. A regression model to predict flexible PU foam shrinkage during the bra cup moulding process was formulated by using the Levenberg-Marquardt method of nonlinear least squares algorithm and verified for accuracy. This study therefore provides an effective approach that optimizes control of the bra cup moulding process and assures the ultimate quality and thickness of moulded foam cups.

  20. The Effects of Dry Cupping Therapy on the Shoulder Pain and Fatigue of Nurses

    Directory of Open Access Journals (Sweden)

    Dorina Sohn

    2011-06-01

    Full Text Available Objective: This research was done to identify the effects of dry cupping therapy on the shoulder pain and fatigue of nurses. Methods: The research design was time series design. The participants were 27 nurses with shoulder pain at P University Hospital in Busan metropolitan city from July 6, 2009 to August 3, 2009. The dry cupping therapy was done 4 times, twice a week for 2 weeks. Before intervention, the severity and frequency of pain and fatigue were measured three times at one week intervals, and then those were measured after one week and two weeks of experimental treatment. The results were analyzed using descriptive statistics, paired t-test and repeated measure ANOVA with the SPSS program. Results: There were statistically significant difference in severity and frequency of shoulder pain,and fatigue after dry cupping therapy. Dry cupping therapy was effective for the management of shoulder pain and fatigue among nurses in this study. Conclusion: Therefore dry cupping therapy can be considered an effective nursing intervention that relieves shoulder pain and fatigue of nurses.

  1. PERANAN METODE PENGOBATAN ISLAM CUPPING THERAPY DALAM PENURUNAN KADAR GLUKOSA DARAH

    Directory of Open Access Journals (Sweden)

    Cut Khairunnisa

    2016-06-01

    Full Text Available The Role of Islamic Treatment Method “Cupping Therapy” to Decrease Blood Glucose Levels. Cupping therapy has long been used by most Muslims and it has occupied as prominent position among therapeutic approaches.The proof of medical modern research lately have been supports expediency therapy which recommended by the prophet. Nowdays,many medical experts who know the benefits of cupping therapy in treating diseases. Diabetes melitus is a disease that is directly related to blood glucose levels. According to the International Diabetes Federation (IDF in 2013, there were 382 million people suffer from diabetes melitus worldwide and Indonesia as seventh ranks in the world. This study aims to determine the effect of cupping therapy on blood glucose levels in patients of Klinik Sehat dr. Abdurrahmân Medan in 2014. The Study used pre-experimental method with one group pre-test and post-test without a control group and sample took by randomization with a sample of 32 people. Based on the Wilcoxon test with á = 0.05 obtained p-value = 0.021 that means there were a significant differences in mean blood glucose levels before and after cupping therapy (p-value < á.

  2. Is the menstrual cup harmless? A case report of an unusual cause of renal colic.

    Science.gov (United States)

    Nunes-Carneiro, Diogo; Couto, Tiago; Cavadas, Vítor

    2018-04-09

    Menstrual cup is increasingly gaining acceptance among women to control the menstrual period. The majority of brands advocate that these devices are 100% safe to the users, notwithstanding there are some reports of rare complications associated with these devices. In this case we present a woman who developed a right renal colic using a menstrual cup. The pain was difficult to manage with conventional analgesics. The plain abdominal X-ray revealed the device in the pelvis occupying more than one third of the pelvis minor diameter and oriented to the right side. The ultrasound revealed right ureterohydronephrosis with no identifiable obstructive cause. The symptoms and the ureterohydronephrosis relieved completely after the removal of the device. Despite of being a safe device, problems with the menstrual cup could occur and we believe that the mechanism behind this clinical picture was the extrinsic compression of the right ureter by the cup. The control of the pain in this patient was challenging and we managed the problem with the device removal. The menstrual cup is gaining acceptance among women and it is important for clinicians to be aware of this device and possible complications associated with its use. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

  3. The Effects of Cupping on Hamstring Flexibility in Collegiate Soccer Players.

    Science.gov (United States)

    Williams, Jeffrey G; Gard, Hannah I; Gregory, Jeana M; Gibson, Amy; Austin, Jennifer

    2018-01-24

    Collegiate soccer players suffer hamstring injuries due to inflexibility and repetitive motions involving intense hamstring lengthening and contraction during sport. Although a popular intervention for muscular injury, there exists limited evidence of the effects of therapeutic cupping on hamstring flexibility. To determine the effect of cupping therapy on hamstring flexibility in collegiate soccer players. Cohort design. Athletic training clinic. Twenty-five, asymptomatic, NCAA Division III soccer players (10 males, 15 females) (age = 19.4 ± 1.30 years, height = 175.1 ± 8.2 cm, mass = 69.5 ± 6.6 kg). A 7-minute therapeutic cupping treatment was delivered to the treatment group. Four 2-inch cups were fixed atop trigger point locations within the hamstring muscle bellies of participants' dominant legs. Control group participants received no intervention between pre- and post-test measurements. Pretest and posttest measurements of hamstring flexibility, using a Passive Straight Leg Raise (PSLR), were performed on both groups. PSLR measurements were conducted by blinded examiners using a digital inclinometer. An independent samples t-test was used to analyze changes in hamstring flexibility from pre- to post-treatment with p-values set a priori at 0.05. An independent samples t-test demonstrated no significant difference in change in hamstring flexibility between participants in the treatment group and those in the control group (t 23 = -.961, p = .35). The findings of this study demonstrated no statistically significant changes in hamstring flexibility following a cupping treatment.

  4. Construction of the Faraday Cup based on fluorescent screen as an electron beam sensor

    International Nuclear Information System (INIS)

    Sutadi; Rany Saptaaji; Suhartono; Sukaryono

    2016-01-01

    The Faraday Cup based on fluorescent screen as an electron beam profile sensor at electron accelerator has been conducted. In the principle, the electron beam which obtained from the electron source and accelerated in the accelerator tube will obtain the light which can be observed visually when it interact with fluorescent material (phosphorescent). This Faraday Cup for electron beam sensor was made from the modified TV tube. The main component of this Faraday Cup construction includes: 17 inch TV tube, SS reducer flange and the vacuum adhesive. There are two kind of test has been conducted, that is the vacuum level test and the electron beam sensor test. The vacuum level test was conducted by measuring the final vacuum level that can be reach, while the electron beam sensor test was conducted by monitoring of the electron beam profile that was trapped by Faraday Cup visually. The test result shows that TV tube can be modified as the Faraday Cup to sensor electron beam in the electron accelerator. (author)

  5. Antidoping programme and biological monitoring before and during the 2014 FIFA World Cup Brazil.

    Science.gov (United States)

    Baume, Norbert; Jan, Nicolas; Emery, Caroline; Mandanis, Béatrice; Schweizer, Carine; Giraud, Sylvain; Leuenberger, Nicolas; Marclay, François; Nicoli, Raul; Perrenoud, Laurent; Robinson, Neil; Dvorak, Jiri; Saugy, Martial

    2015-05-01

    The FIFA has implemented an important antidoping programme for the 2014 FIFA World Cup. To perform the analyses before and during the World Cup with biological monitoring of blood and urine samples. All qualified players from the 32 teams participating in the World Cup were tested out-of-competition. During the World Cup, 2-8 players per match were tested. Over 1000 samples were collected in total and analysed in the WADA accredited Laboratory of Lausanne. The quality of the analyses was at the required level as described in the WADA technical documents. The urinary steroid profiles of the players were stable and consistent with previously published papers on football players. During the competition, amphetamine was detected in a sample collected on a player who had a therapeutic use exemption for attention deficit hyperactivity disorder. The blood passport data showed no significant difference in haemoglobin values between out-of-competition and postmatch samples. Logistical issues linked to biological samples collection, and the overseas shipment during the World Cup did not impair the quality of the analyses, especially when used as the biological passport of football players. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  6. Cup anemometer response to the wind turbulence-measurement of the horizontal wind variance

    Directory of Open Access Journals (Sweden)

    S. Yahaya

    2004-11-01

    Full Text Available This paper presents some dynamic characteristics of an opto-electronic cup anemometer model in relation to its response to the wind turbulence. It is based on experimental data of the natural wind turbulence measured both by an ultrasonic anemometer and two samples of the mentioned cup anemometer. The distance constants of the latter devices measured in a wind tunnel are in good agreement with those determined by the spectral analysis method proposed in this study. In addition, the study shows that the linear compensation of the cup anemometer response, beyond the cutoff frequency, is limited to a given frequency, characteristic of the device. Beyond this frequency, the compensation effectiveness relies mainly on the wind characteristics, particularly the direction variability and the horizontal turbulence intensity. Finally, this study demonstrates the potential of fast cup anemometers to measure some turbulence parameters (like wind variance with errors of the magnitude as those deriving from the mean speed measurements. This result proves that fast cup anemometers can be used to assess some turbulence parameters, especially for long-term measurements in severe climate conditions (icing, snowing or sandy storm weathers.

  7. Radiological and migration results of the DURALOC(R)-cup after two years

    CERN Document Server

    Juen, F

    2000-01-01

    4 years of implantation was assessed to be 1.23 mm, however a decreasing speed of migration over the final 2-year-period was indicated. Our results demonstrate that statements relating to migration results of particular cups are more accurate after four years. However, statements about mean migration values are possible after two years. A migration speed of 1 mm total migration within the first 2 years after operation was predictive for radiological loosening of the cup after four years (p=0,0004). Further, appearance of postoperative gaps in zone one of the cup correlate with high migration values later leading to radiological loosening and may be a result of errors during implantation. However, we could demonstrate that presence of gaps around the cup postoperatively is an important factor for later loosening. With consideration to the findings concerning the DURALOC(R) cup within four years of implantation, predictions of results over a long term may be undesirable. In 1997 a study was conduced concerning ...

  8. Estimation of anisotropic permeability in trabecular bone based on microCT imaging and pore-scale fluid dynamics simulations.

    Science.gov (United States)

    Daish, C; Blanchard, R; Gulati, K; Losic, D; Findlay, D; Harvie, D J E; Pivonka, P

    2017-06-01

    In this paper, a comprehensive framework is proposed to estimate the anisotropic permeability matrix in trabecular bone specimens based on micro-computed tomography (microCT) imaging combined with pore-scale fluid dynamics simulations. Two essential steps in the proposed methodology are the selection of (i) a representative volume element (RVE) for calculation of trabecular bone permeability and (ii) a converged mesh for accurate calculation of pore fluid flow properties. Accurate estimates of trabecular bone porosities are obtained using a microCT image resolution of approximately 10 μm. We show that a trabecular bone RVE in the order of 2 × 2 × 2 mm 3 is most suitable. Mesh convergence studies show that accurate fluid flow properties are obtained for a mesh size above 125,000 elements. Volume averaging of the pore-scale fluid flow properties allows calculation of the apparent permeability matrix of trabecular bone specimens. For the four specimens chosen, our numerical results show that the so obtained permeability coefficients are in excellent agreement with previously reported experimental data for both human and bovine trabecular bone samples. We also identified that bone samples taken from long bones generally exhibit a larger permeability in the longitudinal direction. The fact that all coefficients of the permeability matrix were different from zero indicates that bone samples are generally not harvested in the principal flow directions. The full permeability matrix was diagonalized by calculating the eigenvalues, while the eigenvectors showed how strongly the bone sample's orientations deviated from the principal flow directions. Porosity values of the four bone specimens range from 0.83 to 0.86, with a low standard deviation of ± 0.016, principal permeability values range from 0.22 to 1.45 ⋅ 10  -8  m 2 , with a high standard deviation of ± 0.33. Also, the anisotropic ratio ranged from 0.27 to 0.83, with high standard deviation. These

  9. Successes and Failures of a Freedom™ Constrained Cup Used in a Major Salvage Procedure

    Directory of Open Access Journals (Sweden)

    Thomas Donaldson

    2017-10-01

    Full Text Available Background: This is a case report of a 36mm constrained cup (Freedom™, Biomet IN that performed successfully for 7-years in a salvage case involving a total-femur implanted in a leg already short by 3-4 inches. The goal was to enhance hip motion and stability using a 36mm head instead of the usual 32mm size. Templating indications were for a 50mm cup (Freedom™; Arcom™ liner. The proximal femur inserted in 2008 incorporated the 36mm constrained THA and was anchored distally to bone using the Compress™ fixator. By 2012 the fixator loosened and was replaced by hinged total-knee arthroplasty (TKA. The THA was retained at revision and patient’s clinical follow-up was satisfactory for 4 years. As indicated by Martel radiographic method, the Arcom™ liner showed minimal wear over this period. Radiographs in Feb-2016 showed the cup’s constraint ring had rotated slightly but the patient had no symptoms. By Dec-2016, the patient had experienced three falls and also had heard a popping sound in her hip. At Dec-2016 office visit, radiographs indicated additional rotation of the constraint ring and CT scans showed an eccentric head position contacting the metal shell. At revision, 50% of the Arcom rim was ablated and the remainder present as a loose fragment. Following insertion of new Freedom liner and 36mm head, her follow-up appears satisfactory 10-months later. Her leg shortening remains but she walks to office visits using a cane and doesn’t need the cane at home. Methods: Retrieved Arcom liner and detached rim fragment were reconstructed, photographed, and then bi-valved for comparison to similarly prepared exemplar liners, one identical to our revision and one with a thicker wall. Details of liner sections were taken from photographs and reconstructed by computer graphics (Canvas Draw-3™. Wear performance over the first 7 years was assessed using the Martel x-ray method. Results: Inspection of retrieved liner showed a large oval

  10. Reconstruction of head impacts in FIS World Cup alpine skiing.

    Science.gov (United States)

    Steenstrup, Sophie Elspeth; Mok, Kam-Ming; McIntosh, Andrew S; Bahr, Roald; Krosshaug, Tron

    2017-11-25

    Prior to the 2013/2014 season, the International Ski Federation (FIS) increased the helmet testing speed from 5.4 to 6.8 m/s for alpine downhill, super-G and giant slalom. Whether this increased testing speed reflects head impact velocities in real head injury situations on snow is unclear. We therefore investigated the injury mechanisms and gross head impact biomechanics in seven real head injury situations among World Cup (WC) alpine skiers. We analysed nine head impacts from seven head injury videos from the FIS Injury Surveillance System, throughout nine WC seasons (2006-2015) in detail. We used commercial video-based motion analysis software to estimate head impact kinematics in two dimensions, including directly preimpact and postimpact, from broadcast video. The sagittal plane angular movement of the head was also measured using angle measurement software. In seven of nine head impacts, the estimated normal to slope preimpact velocity was higher than the current FIS helmet rule of 6.8 m/s (mean 8.1 (±SD 0.6) m/s, range 1.9±0.8 to 12.1±0.4 m/s). The nine head impacts had a mean normal to slope velocity change of 9.3±1.0 m/s, range 5.2±1.1 to 13.5±1.3 m/s. There was a large change in sagittal plane angular velocity (mean 43.3±2.9 rad/s (range 21.2±1.5 to 64.2±3.0 rad/s)) during impact. The estimated normal to slope preimpact velocity was higher than the current FIS helmet rule of 6.8 m/s in seven of nine head impacts. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  11. Advanced methods for the quantification of trabecular bone structure and density in micro computed tomography images

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Jing

    2011-07-01

    Bone remodeling is a life long process composed of bone formation and resorption. Imbalance between bone formation and resorption is a cause of metabolic bone diseases. Thus, the understanding of factors that affect the remodeling balance is of great importance. Conventionally bone structure is measured using histomorphometry of thin stained sections which is destructive and non-reproducible. In contrast, volumetric microcomputed tomography ({mu}CT) imaging is a powerful tool for quantifying bone quality of small samples non-destructively. The aim of this thesis is to develop an analysis tool to quantify trabecular bone of mouse tibiae with high efficiency, accuracy and reproducibility. Materials and Methods: The trabecular volume of interest (VOI) definition in the proximal metaphysis of mouse tibiae includes three segmentation steps: the periosteal surface, the primary spongiosa and the proximal metaphysis. All these segmentation algorithms are hybrid volume growing-based approaches including automatic threshold estimation, volume growing with different criterions and combined morphological operations. To preserve the connectivity of the trabecular network volume growing with local adaptive thresholding (LAT) is used for the segmentation of the trabeculae. In order to accelerate this process the algorithm is only applied to voxels with gray values in an interval defined by two global thresholds. These are automatically determined and depend on the voxel-to-object-size ratio of the dataset. Standard bone structural parameters were implemented [29, 30, 62]. For the assessment of tissue mineral density (TMD), a calibration phantom made of epoxy resin-based material with two hydroxyapatite (HA) inserts was developed. Experiments were performed with the {mu}CT FORBILD scanner of the IMP to validate the homogeneity of the phantom inserts, the water equivalence of the epoxy resin-based plastic, the effect of beam hardening and the stability of the {mu}CT calibration

  12. Effect of palady and cup feeding on premature neonates′ weight gain and reaching full oral feeding time interval

    Directory of Open Access Journals (Sweden)

    Maryam Marofi

    2016-01-01

    Full Text Available Background: Premature neonates′ feeding is of great importance due to its effective role in their growth. These neonates should reach an independent oral nutrition stage before being discharged from the Neonatal Intensive care Unit. Therefore, the researcher decided to conduct a study on the effect of palady and cup feeding on premature neonates′ weight gain and their reaching full oral feeding time interval. Materials and Methods: This is a clinical trial with a quantitative design conducted on 69 premature infants (gestational age between 29 and 32 weeks who were assigned to cup (n = 34 and palady (n = 35 feeding groups through random allocation. The first feeding was administrated either by cup or palady method in each shift within seven sequential days (total of 21 cup and palady feedings. Then, the rest of feeding was administrated by gavage. Results: Mean hospitalization time (cup = 39.01 and palady = 30.4; P < 0.001 and mean time interval to reach full oral feeding (cup = 33.7 and palady = 24.1; P < 0.001 were significantly lower in palady group compared to cup group. Mean weight changes of neonates 7 weeks after the intervention compared to those in the beginning of the intervention were significantly more in palady group compared to the cup group (cup = 146.7 and palady = 198.8; P < 0.001. Conclusions: The neonates in palady group reached full oral feeding earlier than those of cup group. Subjects′ weight gain was also higher in palady group compared to the cup group. Premature neonates with over 30 weeks of gestational age and physiological stability can be fed by palady.

  13. Rhino horns and paper cups: Deceptive similarities between natural ...

    Indian Academy of Sciences (India)

    behaviour may recommend it to one; another aspect of its behav- iour may press it on the other. While the matter ... hidden – the wheel bearings of our cars, the tool-holding holes of metal lathes, the compression fittings between ... of cones, to remind ourselves, is growth by incremental addition without change of shape.

  14. Cultural change--empowerment at Sweetheart Cup Company, Inc., Bakery Division.

    Science.gov (United States)

    Altomonte, W; Mooney, W; Sheldon, D H

    1999-08-01

    Sweetheart Cup Company always has been associated with fun products--fast food containers, straws, ballpark drink glasses, and maybe the most fun of all--ice cream cones! But making these products of pleasantry at times has not been as festive as it would seem. Sweetheart Cup Company has had its ups and downs in terms of many of the typical manufacturing measurements, but in 1994--under the direction of newly appointed Chief Operating Officer Bill McLaughlin--Sweetheart Cup Company embarked on a new mission. This time everyone would be involved, from headquarters staff in Owings Mills to the fourth-floor oven area workers in the Dallas bakery. The new process goal, "Business Excellence," as we called it, was really an implementation of Class A ERP/MRP II.

  15. FIFA Women's World Cup 2011: pre-competition medical assessment of female referees and assistant referees.

    Science.gov (United States)

    Keller, Dagmar I; Bizzini, Mario; Feddermann, Nina; Junge, Astrid; Dvorak, Jiri

    2013-02-01

    Precompetition screening was implemented for male referees during the 2010 Fédération Internationale de Football Association (FIFA) Word Cup. In contrast, female football referees have been neglected in this respect although they experience similar physical work loads compared to male referees. The standardised football-specific pre-competition medical assessment (PCMA) was performed in 51 referees and assistant referees selected for the 2011 FIFA Women's World Cup. Family history for sudden cardiac death (SCD) was positive in four referees (7.8%), but cardiac examinations did not reveal any pathological findings. Training-unrelated ECG changes were identified in three referees (5.9%), all without correlates in echocardiography or clinical examination. Most common echocardiography findings (66.6%, n=34) were asymptomatic tricuspid and mitral regurgitations. During the present screening, no elite female referee was identified being at risk for SCD, and no referee had to be excluded from participating in the 2011 FIFA Women's World Cup.

  16. A novel method for accurate and reproducible functional cup positioning in total hip arthroplasty.

    Science.gov (United States)

    Meftah, Morteza; Yadav, Akhilesh; Wong, Anthony C; Ranawat, Amar S; Ranawat, Chitranjan S

    2013-08-01

    Cup positioning is an important variable for short and long term function, stability, and durability of total hip arthroplasty (THA). This novel method utilizes internal and external bony landmarks, and the transverse acetabular ligament for positioning the acetabular component. The cup is placed parallel and superior to the transverse ligament and inside the anterior wall notch of the true acetabulum, then adjusted for femoral version and pelvic tilt and obliquity based on weight bearing radiographs. In 78 consecutive THAs, the mean functional anteversion and abduction angles were 17.9° ± 4.7° and 41.7° ± 3.8°, respectively. 96% of the functional anteversion measurements and 100% of the functional abduction angles were within the safe zone. This technique is an easy, reproducible, and accurate method for functional cup placement. Copyright © 2013 Elsevier Inc. All rights reserved.

  17. Validation of 3D sonic-anemometer against cup anemometer response

    DEFF Research Database (Denmark)

    Hansen, Kurt Schaldemose; Larsen, Gunner Chr.; Courtney, Michael

    2004-01-01

    Determination and validation of wind turbine power curves traditionally rely on single point wind speed measurements recorded with a calibrated cup-anemometer. The power curve verification process, which is typically performed in different terrain types, does not always result in satisfactory...... agreement between measures- and predicted power curves. The observed disagreement is premarily believed to relate to the cup-anemometers being sensitive to tilted flow i.e. that the measurement of the horizontal flow component is sensible to flow in a plane perpendicular to the horizontal plane. Furthermore......, the limited cup-anemometer response due to high turbulence can explain some of the diviations. The present paper investigates this problem, by analysing full-scale time series data extracted from "Database on Wind Characteristics" (http://www.winddata.com/), which represents a wide range of sites. Basically...

  18. Characterization of drug-release kinetics in trabecular bone from titania nanotube implants

    Directory of Open Access Journals (Sweden)

    Aw MS

    2012-09-01

    Full Text Available Moom Sinn Aw,1 Kamarul A Khalid,2,3 Karan Gulati,1 Gerald J Atkins,2 Peter Pivonka,4 David M Findlay,2 Dusan Losic11School of Chemical Engineering, 2Discipline of Orthopaedics and Trauma, The University of Adelaide, Adelaide, SA, Australia; 3Department of Orthopaedics, Traumatology and Rehabilitation, Faculty of Medicine, International Islamic University Malaysia, Kuantan, Pahang, Malaysia; 4Engineering Computational Biology Group, School of Computer Science and Software Engineering, The University of Western Australia, Perth, WA, AustraliaPurpose: The aim of this study was to investigate the application of the three-dimensional bone bioreactor for studying drug-release kinetics and distribution of drugs in the ex vivo cancellous bone environment, and to demonstrate the application of nanoengineered titanium (Ti wires generated with titania nanotube (TNT arrays as drug-releasing implants for local drug deliveryMethods: Nanoengineered Ti wires covered with a layer of TNT arrays implanted in bone were used as a drug-releasing implant. Viable bovine trabecular bone was used as the ex vivo bone substrate embedded with the implants and placed in the bone reactor. A hydrophilic fluorescent dye (rhodamine B was used as the model drug, loaded inside the TNT–Ti implants, to monitor drug release and transport in trabecular bone. The distribution of released model drug in the bone was monitored throughout the bone structure, and concentration profiles at different vertical (0–5 mm and horizontal (0–10 mm distances from the implant surface were obtained at a range of release times from 1 hour to 5 days.Results: Scanning electron microscopy confirmed that well-ordered, vertically aligned nanotube arrays were formed on the surface of prepared TNT–Ti wires. Thermogravimetric analysis proved loading of the model drug and fluorescence spectroscopy was used to show drug-release characteristics in-vitro. The drug release from implants inserted into bone ex

  19. The Quality of Trabecular Bone Tissue in Women with Rheumatoid Arthritis

    Directory of Open Access Journals (Sweden)

    V.V. Povoroznyuk

    2013-04-01

    Full Text Available The article deals with the study of the quality index of trabecular bone tissue in patients with rheumatoid arthritis (RA. The study included 134 female patients with RA aged 31 to 78 years (mean age — 52.4 ± 12.7 years; height — 162.6 ± 6.4 cm; weight — 68.5 ± 13.8 kg; average duration of disease — 9.1 ± 7.6 years. In studying the effect of age on the structural and functional state of bone tissue, the examined patients were divided into five groups by decades. In order to evaluate the effect of glucocorticoids (GC on the parameter of quality of trabecular bone and bone mineral density (BMD, the patients were divided into three groups: 1st group comprised 37 patients who did not take GC, 2nd group — 47 patients who had been prescribed with GC only at exacerbation, of the short, less than 6 months term, 3rd group — 50 patients who received systemically GC at a dose of ≥ 5 mg by prednisone for over 3 years. By the method of dual energy X-ray densitometry (Prodigy, GE Lunar, Madison, USA we measured BMD at the lumbar spine, proximal femoral and radial bone. The index of the quality of trabecular bone tissue (TBS of the lumbar spine was determined using the method of TBS iNsight (Med-Imaps, Pessac, France. It is established that starting from the age of 50 years, the indices of TBS L1-L4 (1.156 ± 0.140 vs. 1.318 ± 0.155 in women aged 30–39 years; t = 3.5; p = 0.001 and BMD of different parts of the skeleton in women with RA are significantly decreasing. GC administration is associated with the violation of the quality of the bone tissue. It was revealed that at the systemic administration of GC (in the 3rd group compared to the 1st group, rate of TBS L1-L4 (1.147 ± 0.168 vs 1.250 ± 0.135; t = –3.07; p = 0.003 was significantly lower, while significant changes in BMD parameters of the lumbar spine and femur hadn’t been detected. Over the year of follow-up the index TBS L1-L4 in 1st group decreased by 1.4 %, in 3

  20. Agro-ecological potential of the cup plant (Silphium perfoliatum L.) from a biodiversity perspective

    Science.gov (United States)

    Schrader, Stefan; Schorpp, Quentin; Lena Müller, Anna; Dauber, Jens

    2017-04-01

    The cup plant (Silphium perfoliatum L.) is an alternative bioenergy crop that may contribute to a more environmentally friendly production of renewable resources. The potential benefits of the cup plant are the perennial cultivation without tillage and its flowering-characteristics. Hence it can be hypothesized that beneficial organisms are promoted which in turn improves the provision of ecosystem services like soil fertility and pollination. To date biomass production in Germany is based mainly on cropping systems like intensive maize cultivation that bear a risk for biodiversity and ecosystem services. The importance to counteract this development increases considering the large land requirements for significant generation of energy from biomass. To what extent cropping of the cup plant meets the expectations of a sustainable biomass production was investigated within a comprehensive assessment of soil fauna communities (earthworms, collembolans, nematodes) including their functional groups as well as pollinating insects (bees and hoverflies) including the quantification of pollen and nectar in cup-plant cultivation systems with a crop management close to agricultural practice. From the results it became obvious that the cup plant as a bioenergy crop has got the necessary potential to mitigate the negative development of biodiversity and ecosystem services, especially in regions with a large share of maize monocultures. This agro-ecological potential can only be reached if certain agronomic requirements are met, i.e. a late harvest and cultivation periods of at least five years. Under these conditions the landscape context has to be considered. Semi-natural habitats in the surrounding landscape are required for nesting and larval development of wild pollinator groups. The development of biological functions in soil is tied to the land use history i.e. previous land use: Positive developments are expected for conversion of intensively managed crop fields to the