Small scale CHP: Alternative integration forms in the Danish energy system

International Nuclear Information System (INIS)

Boeg, Rasmus; Gatautis, Ramunas; Engberg Pedersen, Thomas; Schmidt, Rune; Ravn, Hans F.

2003-01-01

In Denmark, introduction of small scale combined heat and power (CHP) plants were part of the energy policy during the 1990's. Thus, the installed electricity capacity on this type of units multiplied approximately ten times during this decade, to constitute more than 2000 MW in 2000, or around 20% of total installed electricity capacity. The motivation for this development was mainly energy savings due to the relatively high thermal efficiency in combined production, and the associated reduction of emissions. The remuneration for the electricity delivered to the electrical network was in part based on a feed in tariff. The construction of the tariff reflected estimated benefits to the electrical system. With the liberalisation of the electricity markets this arrangement has been questioned, and it has been suggested that the differentiated payment to local CHP should be based on electricity market prising. For Denmark this would imply that the local CHP should trade the electricity on the Nordpool electricity spot market. This paper analyses parts of these two alternative ways of economic arrangements in relation to small scale CHP. First it describes the development and status till now. Then it analyses the production patterns and associated economic consequences of a change from the tariff based system to a market system. (BA)

Total cost of ownership of CHP SOFC systems: Effect of installation context

International Nuclear Information System (INIS)

Arduino, Francesco; Santarelli, Massimo

2016-01-01

Solid oxide fuel cells (SOFC) are one of the most interesting between the emerging technologies for energy production. Although some information about the production cost of these devices are already known, their operational cost has not been studied yet with sufficient accuracy. This paper presents a life cycle cost (LCC) analysis of CHP (combined heat and power) SOFC systems performed in hospitals located in various cities of the US and one in Italy. In this study the strong effects of the installation context will be analyzed using a customized use phase model for each location. The cost effectiveness of these devices has been proved without credits in Mondovi (IT), New York (NY) and Minneapolis (MN) where the payback time goes from 10 to 7 years. Considering the credits, it is possible to obtain economic feasibility also in Chicago (IL) and reduce the payback for other cities to values from 4 to 6 years. In other cities like Phoenix (AZ) and Houston (TX) the payback can’t be reached in any case. The life cycle impact assessment analysis has shown how, even in the cities with cleaner electricity grid, there is a reduction in the emissions of both greenhouse gases and pollutants. - Highlights: •Life cycle cost analysis has been performed for CHP SOFC systems. •The strong effects of the installation context have been analyzed. •Economic feasibility has been proven in new york, Minneapolis and Mondovi. •Economic feasibility can’t be reached in phoenix and Houston. •SOFC always provide a reduction in the emissions of greenhouse gases and pollutant.

Micro-CHP systems for residential applications

International Nuclear Information System (INIS)

Paepe, Michel de; D'Herdt, Peter; Mertens, David

2006-01-01

Micro-CHP systems are now emerging on the market. In this paper, a thorough analysis is made of the operational parameters of 3 types of micro-CHP systems for residential use. Two types of houses (detached and terraced) are compared with a two storey apartment. For each building type, the energy demands for electricity and heat are dynamically determined. Using these load profiles, several CHP systems are designed for each building type. Data were obtained for two commercially available gas engines, two Stirling engines and a fuel cell. Using a dynamic simulation, including start up times, these five system types are compared to the separate energy system of a natural gas boiler and buying electricity from the grid. All CHP systems, if well sized, result in a reduction of primary energy use, though different technologies have very different impacts. Gas engines seem to have the best performance. The economic analysis shows that fuel cells are still too expensive and that even the gas engines only have a small internal rate of return (<5%), and this only occurs in favourable economic circumstances. It can, therefore, be concluded that although the different technologies are technically mature, installation costs should at least be reduced by 50% before CHP systems become interesting for residential use. Condensing gas boilers, now very popular in new homes, prove to be economically more interesting and also have a modest effect on primary energy consumption

Experimental study on a project with CHP system basing on absorption cycles

International Nuclear Information System (INIS)

Sun, Jian; Fu, Lin; Sun, Fangtian; Zhang, Shigang

2014-01-01

A new heat recovery system for the CHP (combined heating and power) is presented, and HRU (heat recovery unit) and AHE (absorption heat exchanger) are invented to improve the total energy efficiency of the conventional CHP system by more than 20%, which are installed at the thermal power plant and the heating substation separately. The HRU could recover the low grade heat of exhausted steam from the turbine directly, and the AHE could decrease the temperature of back water of primary pipe to a lower temperature than that of secondary pipe without changing the flow rate of secondary pipe. A large demonstration project employing this technology has been built in Datong of China. And experimental results of HRU and AHE are presented to evaluate this system. - Highlights: • The total energy efficiency of CHP could by increased by more than 20%. • Temperature of back water of primary pipe could be lower than that of secondary pipe. • Heating capacity of primary pipe could be increased significantly. • Low grade heat of exhausted steam from turbine could be recovered directly

Optimal integrated sizing and planning of hubs with midsize/large CHP units considering reliability of supply

International Nuclear Information System (INIS)

Moradi, Saeed; Ghaffarpour, Reza; Ranjbar, Ali Mohammad; Mozaffari, Babak

2017-01-01

Highlights: • New hub planning formulation is proposed to exploit assets of midsize/large CHPs. • Linearization approaches are proposed for two-variable nonlinear CHP fuel function. • Efficient operation of addressed CHPs & hub devices at contingencies are considered. • Reliability-embedded integrated planning & sizing is formulated as one single MILP. • Noticeable results for costs & reliability-embedded planning due to mid/large CHPs. - Abstract: Use of multi-carrier energy systems and the energy hub concept has recently been a widespread trend worldwide. However, most of the related researches specialize in CHP systems with constant electricity/heat ratios and linear operating characteristics. In this paper, integrated energy hub planning and sizing is developed for the energy systems with mid-scale and large-scale CHP units, by taking their wide operating range into consideration. The proposed formulation is aimed at taking the best use of the beneficial degrees of freedom associated with these units for decreasing total costs and increasing reliability. High-accuracy piecewise linearization techniques with approximation errors of about 1% are introduced for the nonlinear two-dimensional CHP input-output function, making it possible to successfully integrate the CHP sizing. Efficient operation of CHP and the hub at contingencies is extracted via a new formulation, which is developed to be incorporated to the planning and sizing problem. Optimal operation, planning, sizing and contingency operation of hub components are integrated and formulated as a single comprehensive MILP problem. Results on a case study with midsize CHPs reveal a 33% reduction in total costs, and it is demonstrated that the proposed formulation ceases the need for additional components/capacities for increasing reliability of supply.

The design of Chp plants

International Nuclear Information System (INIS)

Tomassetti, G.

2001-01-01

Chp is considered with a bottom-up view, as the most efficient way to satisfy the needs of the users. In order to achieve optimal results a particular care must be used in analyzing the thermal and electrical loads and their interactions. On this basis and taking into account the relationships among the user and the suppliers of electricity, fuels and heat, the energy market structure, the cost of energy and the tax assessment it is possible to properly design Chp plants with benefits for the users [it

Evaluation of an alkaline fuel cell system as a micro-CHP

International Nuclear Information System (INIS)

Verhaert, Ivan; Mulder, Grietus; De Paepe, Michel

2016-01-01

Highlights: • Sensitivity analysis on system configuration of the AFC as a micro-CHP. • Flow rate in the secondary heating circuit can be used to control water management. • Part load behavior of fuel cells is compared to other micro-CHP technologies. • For future energy demand in buildings fuel cells have the best performance. - Abstract: Micro-cogeneration is an emerging technology to reduce the non-renewable energy demand in buildings and reduce peak load in the grid. Fuel cell based cogeneration (CHP) has interesting prospects for building applications, even at relatively low heat demand. This is due to their partial load behavior which is completely different, compared to other micro-CHP technologies. Within the fuel cell technologies suitable for small scale CHP or micro-CHP, the existing configuration of an alkaline fuel cell system is analyzed. This analysis is based on validated models and offers a control strategy to optimize both water management and energy performance of the alkaline fuel cell system. Finally, the model of the alkaline fuel cell system with optimized control strategy is used to compare its part load behavior to other micro-CHP technologies.

CHP expansion strategy in North Rhine-Westphalia. A blueprint for other regions

International Nuclear Information System (INIS)

Holzapfel, Dominik; Schneider, Sabine

2015-01-01

The North Rhine-Westphalian state government intends to increase the share of combined heat and power (CHP) generation to at least 25 % by 2020. Since 2013, the campaign ''CHP.NRW - Power Meets Heat'' (''KWK.NRW - Strom trifft Waerme'') of the EnergyAgency.NRW, is has been running on behalf of the NRW Climate Protection Ministry, to publicise this technology and to promote its expansion. The campaign accompanies the State Government's CHP Stimulus Programme. The EnergyAgency.NRW has organised companies and research institutions, associations and interest groups under the umbrella of ''CHP.NRW - Power Meets Heat'', aiming at co-ordinated and intensified activities in the field of combined heat and power generation. The target of the initial-project ''roadmap/CHP.NRW'' of the ''Virtual Institute / CHP.NRW'' is to develop a guideline for the application and optimisation of CHP-systems.

CHP plant Legionowo Poland. Description of the electricity market in Poland/CHP-feasibility analysis

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-04-01

In 1997, a new energy law was passed in Poland. An important element of the law is that local energy is made obligatory. The law describes obligatory tasks and procedures for the Polish municipalities related to planning and organisation of the energy sector. With the objective of supporting the Polish municipalities in their obligations according to the energy law, the project 'Energy Planning in Poland at Municipal Level - Support to Decision Makers' was launched. As part of the project, Municipal Guideline Reports have been elaborated for three model municipalities. These guidelines present the basis for energy supply plans in the three municipalities. For the city of Legionowo, the following was recommended: 1. The planning processes initiated during the project should be continued/followed up, 2. Master Plan for the district heating system should be prepared, 3. The possibilities of establishment of a major natural gas-fired CHP plant of the combined cycle type should be investigated. The present report describes the electricity market in Poland, the market in which a CHP plant in Legionowo will have to operate. Furthermore the report presents the results of the feasibility analysis carried out for a new CHP plant in Legionowo. (BA)

Micro-CHP Systems for Residential Applications

Energy Technology Data Exchange (ETDEWEB)

Timothy DeValve; Benoit Olsommer

2007-09-30

Integrated micro-CHP (Cooling, Heating and Power) system solutions represent an opportunity to address all of the following requirements at once: conservation of scarce energy resources, moderation of pollutant release into our environment, and assured comfort for home-owners. The objective of this effort was to establish strategies for development, demonstration, and sustainable commercialization of cost-effective integrated CHP systems for residential applications. A unified approach to market and opportunity identification, technology assessment, specific system designs, adaptation to modular product platform component conceptual designs was employed. UTRC's recommendation to U.S. Department of Energy is to go ahead with the execution of the proposed product development and commercialization strategy plan under Phase II of this effort. Recent indicators show the emergence of micro-CHP. More than 12,000 micro-CHP systems have been sold worldwide so far, around 7,500 in 2004. Market projections predict a world-wide market growth over 35% per year. In 2004 the installations were mainly in Europe (73.5%) and in Japan (26.4%). The market in North-America is almost non-existent (0.1%). High energy consumption, high energy expenditure, large spark-spread (i.e., difference between electricity and fuel costs), big square footage, and high income are the key conditions for market acceptance. Today, these conditions are best found in the states of New York, Pennsylvania, New Jersey, Wisconsin, Illinois, Indiana, Michigan, Ohio, New England states. A multiple stage development plan is proposed to address risk mitigation. These stages include concept development and supplier engagement, component development, system integration, system demonstration, and field trials. A two stage commercialization strategy is suggested based on two product versions. The first version--a heat and power system named Micro-Cogen, provides the heat and essential electrical power to the

Methodology for evaluation of industrial CHP production

International Nuclear Information System (INIS)

Pavlovic, Nenad V.; Studovic, Milovan

2000-01-01

At the end of the century industry switched from exclusive power consumer into power consumer-producer which is one of the players on the deregulated power market. Consequently, goals of industrial plant optimization have to be changed, making new challenges that industrial management has to be faced with. In the paper is reviewed own methodology for evaluation of industrial power production on deregulated power market. The methodology recognizes economic efficiency of industrial CHP facilities as a main criterion for evaluation. Energy and ecological efficiency are used as additional criteria, in which implicit could be found social goals. Also, methodology recognizes key and limit factors for CHP production in industry. It could be successful applied, by use of available commercial software for energy simulation in CHP plants and economic evaluation. (Authors)

Biomass CHP Catalog of Technologies

Science.gov (United States)

This report reviews the technical and economic characterization of biomass resources, biomass preparation, energy conversion technologies, power production systems, and complete integrated CHP systems.

Evaluation of the impact of the liberalisation of the European electricity market on the CHP, District heating and cooling sector; 'Save CHP/DHC'. Final report

International Nuclear Information System (INIS)

2000-08-01

Improved energy efficiency will play a key role in meeting the EU Kyoto target economically. In addition to a significant positive environmental impact, improved energy efficiency will lead to a more sustainable energy policy and enhanced security of supply. The study: 1) Identifies and evaluates parameters and conditions which in relation to the liberalisation of the electricity market will have an impact on the CHP/DHC sector in EU15 and Poland. 2) Establishes an information base on CHP/DHC systems in EU15 and Poland. 3) Analyses the CHP/DHC sector and its ability to meet changing market conditions. 4) Assesses the effect of the liberalised electricity market on electricity production in relation to CHP/district heating and cooling. 5) Identifies threats for the viability of CHP/DHC in a liberalised market and evaluates means and measures to overcome such threats. The study brings forward the goals and commitments in respect of European energy and environmental policy and gives an overview of the present and expected future framework in which CHP/DHC is to operate. The study evaluates the viability of the sector at an overall level and for different groups/categories of CHP/DHC systems in different countries. The effects of existing or proposed national public measures are analysed. The analyses are essential to decision makers in the transition process towards a fully liberalised market. Recognised uncertainties in the market during the transition period may cause either a temporary or a permanent recession for the CHP/DHC sector. Improved understanding and recognition of threats and opportunities is important to all actors just now. The study can be considered a first step of a process to create a market situation, where the energy customers can make their choices under competition rules and where environmentally friendly and efficient CHP and DHC is considered an attractive business opportunity in competition with other energy supplies. (EHS)

Optimal designs of small CHP plants in a market with fluctuating electricity prices

International Nuclear Information System (INIS)

Lund, H.; Andersen, A.N.

2005-01-01

Combined Heat and Power production (CHP) are essential for implementation of the climate change response objectives in many countries. In an introduction period, small CHP plants have typically been offered fixed electricity prices, but in many countries, such pricing conditions are now being replaced by spot market prices. Consequently, new methodologies and tools for the optimisation of small CHP plant designs are needed. The small CHP plants in Denmark are already experienced in optimising their electricity production against the triple tariff, which has existed for almost 10 years. Consequently, the CHP plants have long term experience in organising when to switch on and off the CHP units in order to optimise their profit. Also, the CHP owners have long term experience in designing their plants. For instance, small CHP plants in Denmark have usually invested in excess capacity on the CHP units in combination with heat storage capacity. Thereby, the plants have increased their performance in order to optimise revenues. This paper presents the Danish experience with methodologies and software tools, which have been used to design investment and operation strategies for almost all small CHP plants in Denmark during the decade of the triple tariff. Moreover, the changes in such methodologies and tools in order to optimise performance in a market with fluctuating electricity prices are presented and discussed

Multi-criteria evaluation for CHP system options

International Nuclear Information System (INIS)

Pilavachi, P.A.; Roumpeas, C.P.; Minett, S.; Afgan, N.H.

2006-01-01

Several Combined Heat and Power (CHP) system options have been considered for evaluation with respect to the end-user requirements. These included Internal Combustion Engines (Otto and Diesel), Gas Turbines, Steam Turbines and Combined Cycles covering a wide range of electrical output. Data have been obtained from literature and the CHP systems have been evaluated using different criteria such as overall efficiency, investment cost, fuel cost, electricity cost, heat cost, CO 2 production and footprint. A multi-criteria method is used with an agglomeration function based on the statistical evaluation of weight factors. The technical, economic and social aspects of each system have been evaluated in an integrated manner and the results have been compared by means of the Sustainability Index. Based on the above criteria and depending on the user requirements, the best CHP system options have been established

CHP systems to save money and cut carbon.

Science.gov (United States)

Hopkins, Ian

2014-10-01

According to Ian Hopkins, a director of ENER-G Combined Power--which has delivered more than 50 CHP-led energy services contracts within the healthcare sector, having, for the past 30 years, designed and manufactured CHP systems at its global headquarters and R&D centre in Salford--'the energy cost and carbon-saving benefits of combined heat and power are difficult to match where there is a large heating/cooling demand over extended periods'. In this article, he explains how hospitals and other busy healthcare facilities thus 'make ideal bedfellows' for CHP, and outlines the key criteria and considerations, such as sizing, for healthcare engineers, when looking to specify such a system.

Mississippi State University Cooling, Heating, and Power (Micro-CHP) and Bio-Fuel Center

Energy Technology Data Exchange (ETDEWEB)

Mago, Pedro [Mississippi State Univ., Mississippi State, MS (United States); Newell, LeLe [Mississippi State Univ., Mississippi State, MS (United States)

2014-01-31

Between 2008 and 2014, the U.S. Department of Energy funded the MSU Micro-CHP and Bio-Fuel Center located at Mississippi State University. The overall objective of this project was to enable micro-CHP (micro-combined heat and power) utilization, to facilitate and promote the use of CHP systems and to educate architects, engineers, and agricultural producers and scientists on the benefits of CHP systems. Therefore, the work of the Center focused on the three areas: CHP system modeling and optimization, outreach, and research. In general, the results obtained from this project demonstrated that CHP systems are attractive because they can provide energy, environmental, and economic benefits. Some of these benefits include the potential to reduce operational cost, carbon dioxide emissions, primary energy consumption, and power reliability during electric grid disruptions. The knowledge disseminated in numerous journal and conference papers from the outcomes of this project is beneficial to engineers, architects, agricultural producers, scientists and the public in general who are interested in CHP technology and applications. In addition, more than 48 graduate students and 23 undergraduate students, benefited from the training and research performed in the MSU Micro-CHP and Bio-Fuel Center.

Small-scale biomass CHP using gasa turbines: a scoping study

International Nuclear Information System (INIS)

James, D.W.; Landen, R.

1996-01-01

Various options for small-scale (up to 250 KWe) Combined Heat and Power (CHP) plants evaluated in this scoping study. Plants using small gas turbines, and able to use biomass fuels when available are included. Three detailed case studies of small-scale biomass CHP plants are compared to match specific technical options with customer requirements. The commercial development of such biomass-fired CHP units, using gas turbines, is shown to be economically viable depending on fuel costs and the continuation of existing financial incentives. (UK)

Is micro-CHP price controllable under price signal controlled Virtual Power Plants?

DEFF Research Database (Denmark)

You, Shi; Træholt, Chresten; Poulsen, Bjarne

2011-01-01

As micro-combined heat and power (micro-CHP) systems move towards mass deployment together with other kinds of distributed energy resources (DER), an increasing emphasis has been placed on how to coordinate such a large diversified DER portfolio in an efficient way by the Virtual Power Plant (VPP...... for three different micro-CHP systems to investigate the feasibility of being controlled by price. Such analysis is relevant for both controller designs for micro-CHP systems and VPP related operations. The results indicate that controlling the micro-CHP systems by price is feasible but could result...

Micro-CHP Technologies Roadmap: Meeting 21st Century Residential Energy Needs

Energy Technology Data Exchange (ETDEWEB)

none,

2003-12-01

On June 11-12, 2003, at Greenbelt, Maryland, key stakeholders from industry, government agencies, universities, and others involved in combined heat and power and the residential buildings industry explores solutions to technical, institutional, and market barriers facing micro-combined heat and power systems (mCHP). Participants outlined a desired future for mCHP systems, identified specific interim technology cost and performance targets, and developed actions to achieve the interim targets and vision. This document, The Micro-CHP Technologies Roadmap, is a result of their deliberations. It outlines a set of actions that can be pursued by both the government and industry to develop mCHP appliances for creating a new approach for households to meet their energy needs.

CHP and District Cooling: An Assessment of Market and Policy Potential in India

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

This report contains an assessment of India's CHP/DC status and recommendations for addressing barriers to allow India to meet its energy efficiency targets. Such barriers include a lack of governmental emphasis on CHP, the absence of a clear methodology for calculating CO2 emission reductions from CHP/DHC, and a tax and duty structure for CHP capital equipment that is not as attractive as for other renewable energy technologies.

The role of combined heat and power (CHP) in energy and climate policy

International Nuclear Information System (INIS)

Conrad, F.

1993-03-01

In the energy- and environment context CHP is said to be especially energy saving and climate preserving. This report shows that from the standpoint of energy economics as well as under technical aspects this judgement holds true only under special conditions. Depending on the technical parameters, the concrete circumstances of operation and the characteristics of the power plants and heating systems compared to CHP-plants the range of realistic energy savings turns out to be very large. Related overstimations are to a good extend caused by the traditional practice of granting the energetic advantage of CHP exclusively to the district heating. If this advantage is credited to heat and power as equal shares space heating with cogenerated power of 80% efficiency reveals to be very energy conserving. The uno actu utilization of cogenerated heat and power, for the same purpose could facilitate the expansion of CHP, since the problems related to the feeding of cogenerated power into the grid for general purposes would disappear. The second main issue of this report concerns the abatement of CO 2 -emissions with the aid of CHP. Fuelled with natural gas, CHP-plants are attractive instruments for climate policy. This is especially true if CHP is compared to old coal-based power plants and oil-fuelled old heating systems. In the FRG, however, hard coal, and not natural gas, will be the main fuel for future CHP, lowering its CO 2 -advantage considerably. On the other hand high efficient combi-power plants (gas turbine plus condensing turbine) and gas heating systems have to be included in the comparative analyse. Compared to these advanced systems the CO 2 -characteristics of CHP are inferior. Moreover, the specific CO 2 -advantage of natural gas is better used by such modern mono systems rather than CHP-plants. (orig.) [de

CHP as a Boiler Replacement Opportunity (Webinar) – April 30, 2013

Science.gov (United States)

This webinar provides information about the benefits of replacing a boiler with a CHP system, describes CHP project analysis and delivery processes, and highlights a case study at Penn State University.

Multi-Objective Analysis of a CHP Plant Integrated Microgrid in Pakistan

Directory of Open Access Journals (Sweden)

Asad Waqar

2017-10-01

Full Text Available In developing countries like Pakistan, the capacity shortage (CS of electricity is a critical problem. The frequent natural gas (NG outages compel consumers to use electricity to fulfill the thermal loads, which ends up as an increase in electrical load. In this scenario, the authors have proposed the concept of a combined heat & power (CHP plant to be a better option for supplying both electrical and thermal loads simultaneously. A CHP plant-based microgrid comprising a PV array, diesel generators and batteries (operating in grid-connected as well as islanded modes has been simulated using the HOMER Pro software. Different configurations of distributed generators (DGs with/without batteries have been evaluated considering multiple objectives. The multiple objectives include the minimization of the total net present cost (TNPC, cost of generated energy (COE and the annual greenhouse gas (GHG emissions, as well as the maximization of annual waste heat recovery (WHR of thermal units and annual grid sales (GS. These objectives are subject to the constraints of power balance, battery operation within state of charge (SOC limits, generator operation within capacity limits and zero capacity shortage. The simulations have been performed on six cities including Islamabad, Lahore, Karachi, Peshawar, Quetta and Gilgit. The simulation results have been analyzed to find the most optimal city for the CHP plant integrated microgrid.

Combined Heat and Power (CHP) as a Compliance Option under the Clean Power Plan: A Template and Policy Options for State Regulators

Energy Technology Data Exchange (ETDEWEB)

None

2015-07-30

Combined Heat and Power (CHP) is an important option for states to consider in developing strategies to meet their emission targets under the US Environmental Protection Agency's Clean Power Plan. This Template is designed to highlight key issues that states should consider when evaluating whether CHP could be a meaningful component of their compliance plans. It demonstrates that CHP can be a valuable approach for reducing emissions and helping states achieve their targets. While the report does not endorse any particular approach for any state, and actual plans will vary dependent upon state-specific factors and determinations, it provides tools and resources that states can use to begin the process, and underscores the opportunity CHP represents for many states. . By producing both heat and electricity from a single fuel source, CHP offers significant energy savings and carbon emissions benefits over the separate generation of heat and power, with a typical unit producing electricity with half the emissions of conventional generation. These efficiency gains translate to economic savings and enhanced competitiveness for CHP hosts, and emissions reductions for the state, along with helping to lower electric bills; and creating jobs in the design, construction, installation and maintenance of equipment. In 2015, CHP represents 8 percent of electric capacity in the United States and provides 12 percent of total power generation. Projects already exist in all 50 states, but significant technical and economic potential remains. CHP offers a tested way for states to achieve their emission limits while advancing a host of ancillary benefits.

Heat Pumps in CHP Systems

DEFF Research Database (Denmark)

Ommen, Torben Schmidt

that three configurations are particular advantageous, whereas the two remaining configurations result in system performance close to or below what may be expected from an electric heater. One of the three advantageous configurations is required to be positioned at the location of the heat demand, whereas...... the two remaining can be located at positions with availability of high temperature sources by utilising the DH network to distribute the heat. A large amount of operational and economic constraints limit the applicability of HPs operated with natural working fluids, which may be the only feasible choice...... representation allows infeasible production. Using MIP or NLP optimisation, the number of operation hours and the total production of heat from HPs are significantly increased, as the HPs may be used to shave the load patterns of CHP units in significantly constrained energy systems. A MIP energy system model...

CHP plant Legionowo Poland - Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-12-01

In 1997, a new Energy Law was passed in Poland. An important element of the law is that local energy planning is made obligatory. The law describes obligatory tasks and procedures for Polish municipalities related to planning and organisation of the energy sector. With the objective of supporting the Polish municipalities in their obligations according to the energy law of 1997, the project 'Energy Planning in Poland at Municipal Level - Support to Decision Makers' was launched. As part of the project, Municipal Guideline Reports have been elaborated for three model municipalities. These guidelines present the basis for the Energy Supply Plans in these municipalities. For the city of Legionowo, the following was recommended: 1. The planning processes initiated during the project should be continues/followed up, 2. Master Plan for the district heating system should be prepared, 3. The possibilities of establishment of a major natural gas-fired CHP plant of the Combined Cycle type should be investigated. The present report is the final Master Plan based on the following reports: Master Plan for Legionowo - Status Report; Master Plan for Legionowo - Hydraulic Analysis; CHP Plant Legionowo Poland - CHP Feasibility Analysis. The final Master Plan describes the status in the DH Company in Legionowo, possible improvements and an investment plan for the selected scenario. (BA)

Modelling Danish local CHP on market conditions

DEFF Research Database (Denmark)

Ravn, Hans V.; Riisom, Jannik; Schaumburg-Müller, Camilla

2004-01-01

with the liberalisation process of the energy sectors of the EU countries, it is however anticipated that Danish local CHP are to begin operating on market conditions within the year 2005. This means that the income that the local CHPs previously gained from selling electricity at the feed-in tariff is replaced in part...... the consequences of acting in a liberalised market for a given CHP plant, based on the abovementioned bottom-up model. The key assumption determining the bottom line is the electricity spot price. The formation of the spot price in the Nordic area depends heavily upon the state of the water reservoirs in Norway...

A study on electricity export capability of the μCHP system with spot price

DEFF Research Database (Denmark)

You, Shi; Træholt, Chresten; Poulsen, Bjarne

2009-01-01

of the muCHP unit, which influence the export capability of muCHP system, is firstly carried out in the intraday case study, followed by the annual case study which explores the annual system performance. The results show that the electricity export capability of a muCHP system is closely related to its...

Integration of hydrothermal carbonization and a CHP plant: Part 2 –operational and economic analysis

International Nuclear Information System (INIS)

Saari, Jussi; Sermyagina, Ekaterina; Kaikko, Juha; Vakkilainen, Esa; Sergeev, Vitaly

2016-01-01

Wood-fired combined heat and power (CHP) plants are a proven technology for producing domestic, carbon-neutral heat and power in Nordic countries. One drawback of CHP plants is the low capacity factors due to varying heat loads. In the current economic environment, uncertainty over energy prices creates also uncertainty over investment profitability. Hydrothermal carbonization (HTC) is a promising thermochemical conversion technology for producing an improved, more versatile wood-based fuel. Integrating HTC with a CHP plant allows simplifying the HTC process and extending the CHP plant operating time. An integrated polygeneration plant producing three energy products is also less sensitive to price changes in any one product. This study compares three integration cases chosen from the previous paper, and the case of separate stand-alone plants. The best economic performance is obtained using pressurized hot water from the CHP plant boiler drum as HTC process water. This has the poorest efficiency, but allows the greatest cost reduction in the HTC process and longest CHP plant operating time. The result demonstrates the suitability of CHP plants for integration with a HTC process, and the importance of economic and operational analysis considering annual load variations in sufficient detail. - Highlights: • Integration of wood hydrothermal carbonization with a small CHP plant studied. • Operation and economics of three concepts and stand-alone plants are compared. • Sensitivity analysis is performed. • Results show technical and thermodynamic analysis inadequate and misleading alone. • Minimizing HTC investment, extending CHP operating time important for profitability.

MICRO-CHP System for Residential Applications

Energy Technology Data Exchange (ETDEWEB)

Joseph Gerstmann

2009-01-31

This is the final report of progress under Phase I of a project to develop and commercialize a micro-CHP system for residential applications that provides electrical power, heating, and cooling for the home. This is the first phase of a three-phase effort in which the residential micro-CHP system will be designed (Phase I), developed and tested in the laboratory (Phase II); and further developed and field tested (Phase III). The project team consists of Advanced Mechanical Technology, Inc. (AMTI), responsible for system design and integration; Marathon Engine Systems, Inc. (MES), responsible for design of the engine-generator subsystem; AO Smith, responsible for design of the thermal storage and water heating subsystems; Trane, a business of American Standard Companies, responsible for design of the HVAC subsystem; and AirXchange, Inc., responsible for design of the mechanical ventilation and dehumidification subsystem.

Management of fluctuations in wind power and CHP comparing two possible Danish strategies

International Nuclear Information System (INIS)

Lund, H.; Clark, W.W.

2002-01-01

Both CHP (combined heat and power production) and wind power are important elements of Danish energy policy. Today, approximately 50% of both the Danish electricity and heat demand are produced in CHP and more than 15% of the electricity demand is produced by wind turbines. Both technologies are essential for the implementation of Danish climate change response objectives, and both technologies are intended for further expansion in the coming decade. Meanwhile, the integration of CHP and wind power is subject to fluctuations in electricity production. Wind turbines depend on the wind, and CHP depends on the heat demand. This article discusses and analyses two different national strategies for solving this problem. One strategy, which is the current official government policy known as the export strategy, proposes to take advantage of the Nordic and European markets for selling and buying electricity. In this case, surplus electricity from wind power and CHP simply will be sold to neighbouring countries. Another strategy, the self-supply strategy, runs the CHP units to meet both demand and the fluctuations in the wind scheduling. In this case, investments in heat storages are necessary and heat pumps have to be added to the CHP units. Based on official Danish energy policy and energy plans, this article quantifies the problem for the year 2015 in terms of the amount of surplus electricity, and investments in heat pumps, etc. needed to solve the problem are calculated. Based on these results between the two different strategies, the conclusion is that the self-supply strategy is recommended over the official export strategy. (author)

Carbon emissions reduction potential in the US chemicals and pulp and paper industries by applying CHP technologies

International Nuclear Information System (INIS)

Khrushch, M.; Worrell, E.; Price, L.; Martin, N.; Einstein, D.

1999-01-01

The chemical and the pulp/paper industries combined provide 55% of CHP generation in the US industry. Yet, significant potential for new CHP capacities exists in both industries. From the present steam consumption data, the authors estimate about 50 GW of additional technical potential for CHP in both industries. The reduced carbon emissions will be equivalent to 44% of the present carbon emissions in these industries. They find that most of the carbon emissions reductions can be achieved at negative costs. Depending on the assumptions used in calculations, the economic potential of CHP in these industries can be significantly lower, and carbon emissions mitigation costs can be much higher. Using sensitivity analyses, they determine that the largest effect on the CHP estimate have the assumptions in the costs of CHP technology, in the assumed discount rates, in improvements in efficiency of CHP technologies, and in the CHP equipment depreciation periods. Changes in fuel and electricity prices and the growth in the industries' steam demand have less of an effect. They conclude that the lowest carbon mitigation costs are achieved with the CHP facility is operated by the utility and when industrial company that owns the CHP unit can sell extra electricity and steam to the open wholesale market. Based on the results of the analyses they discuss policy implications

Future market relevance of CHP installations with electrical ratings from 1 to 1000 kW

International Nuclear Information System (INIS)

Eicher, H.; Rigassi, R.

2003-12-01

This report for the Swiss Federal Office of Energy (SFOE) discusses the future market relevance of combined heat and power (CHP) installations with electrical ratings from 1 to 1000 kW. Developments over the past ten years are reviewed. Important reductions in the price of motor-driven CHP units and the price of the electrical power produced are noted and commented on. The technical market potential of CHP units and the degree to which this potential has been implemented are commented on. Work done, including CHP implementation in the industrial, commercial and residential areas, is commented on. Future developments both in the technical area as well as in commercial areas are commented on. Micro-gas-turbine based CHP systems are also discussed, as are fuel-cell based systems in both the higher and lower capacity power generation area. The prospects for CHP systems in general in the electricity generation area are discussed

Examination of energy price policies in Iran for optimal configuration of CHP and CCHP systems based on particle swarm optimization algorithm

International Nuclear Information System (INIS)

Tichi, S.G.; Ardehali, M.M.; Nazari, M.E.

2010-01-01

The current subsidized energy prices in Iran are proposed to be gradually eliminated over the next few years. The objective of this study is to examine the effects of current and future energy price policies on optimal configuration of combined heat and power (CHP) and combined cooling, heating, and power (CCHP) systems in Iran, under the conditions of selling and not-selling electricity to utility. The particle swarm optimization algorithm is used for minimizing the cost function for owning and operating various CHP and CCHP systems in an industrial dairy unit. The results show that with the estimated future unsubsidized utility prices, CHP and CCHP systems operating with reciprocating engine prime mover have total costs of 5.6 and $2.9x10 6 over useful life of 20 years, respectively, while both systems have the same capital recovery periods of 1.3 years. However, for the same prime mover and with current subsidized prices, CHP and CCHP systems require 4.9 and 5.2 years for capital recovery, respectively. It is concluded that the current energy price policies hinder the promotion of installing CHP and CCHP systems and, the policy of selling electricity to utility as well as eliminating subsidies are prerequisites to successful widespread utilization of such systems.

Should a small combined heat and power plant (CHP) open to its regional power and heat networks? Integrated economic, energy, and emergy evaluation of optimization plans for Jiufa CHP

International Nuclear Information System (INIS)

Peng, T.; Lu, H.F.; Wu, W.L.; Campbell, D.E.; Zhao, G.S.; Zou, J.H.; Chen, J.

2008-01-01

The development of industrial ecology has led company managers to increasingly consider their company's niche in the regional system, and to develop optimization plans. We used emergy-based, ecological-economic synthesis to evaluate two optimization plans for the Jiufa Combined Heat and Power (CHP) Plant, Shandong China. In addition, we performed economic input-output analysis and energy analysis on the system. The results showed that appropriately incorporating a firm with temporary extra productivity into its regional system will help maximize the total productivity and improve ecological-economic efficiency and benefits to society, even without technical optimization of the firm itself. In addition, developing a closer relationship between a company and its regional system will facilitate the development of new optimization opportunities. Small coal-based CHP plants have lower-energy efficiency, higher environmental loading, and lower sustainability than large fossil fuel and renewable energy-based systems. The emergy exchange ratio (EER) proved to be an important index for evaluating the vitality of highly developed ecological-economic systems

Thermodynamic evaluation of CHP (combined heat and power) plants integrated with installations of coal gasification

International Nuclear Information System (INIS)

Ziębik, Andrzej; Malik, Tomasz; Liszka, Marcin

2015-01-01

Integration of a CHP steam plant with an installation of coal gasification and gas turbine leads to an IGCC-CHP (integrated gasification combined cycle-combined heat and power). Two installations of coal gasification have been analyzed, i.e. pressurized entrained flow gasifier – case 1 and pressurized fluidized bed gasifier with CO_2 recirculation – case 2. Basing on the results of mathematical modelling of an IGCC-CHP plant, the algorithms of calculating typical energy indices have been derived. The following energy indices are considered, i.e. coefficient of heat performance and relative savings of chemical energy of fuels. The results of coefficients of heat performance are contained between 1.87 and 2.37. Values exceeding 1 are thermodynamically justified because the idea of cogeneration of heat and electricity based on combining cycles of the heat engine and heat pump the efficiency of which exceeds 1. Higher values concerning waste heat replace more thermodynamically effective sources of heat in CHP plants. Relative savings of the chemical energy of fuels are similar in both cases of IGCC-CHP plants and are contained between the lower value of the CHP (combined heat and power) plants fuelled with coal and higher value of CHP plants fired with natural gas. - Highlights: • Energy savings of fuel is an adequate measure of cogeneration. • Relative energy savings of IGCC-CHP is near the result of a gas and steam CHP. • COHP (coefficient of heat performance) can help to divide fuel between heat fluxes. • Higher values of COHP in the case of waste heat recovery result from the lower thermal parameters.

Demonstration Stirling Engine based Micro-CHP with ultra-low emissions

Energy Technology Data Exchange (ETDEWEB)

Oeberg, Rolf; Olsson, Fredrik [Carl Bro Energikonsult AB (Sweden); Paalsson, Magnus [Lund Inst. of Technology (Sweden)

2004-03-01

This project has been initiated in order to develop a new type of natural gas fired low emission combustion system for a Stirling engine CHP-unit, and to demonstrate and evaluate the unit with the newly developed combustion system in a CHP application. The Stirling engine technology is well developed, but mostly used in special applications and CHP-applications are scarce. The very low exhaust emissions with the new combustion system would make the Stirling engine very suitable for installation in as a CHP-unit in domestic areas. The Stirling engine used in the project has been a V161 engine produced by Solo Kleinmotoren GmbH in Sindelfingen. The unit has a nominal output of 7,5 kW{sub el} and 20 kW{sub heat} (Hot water). The new combustion system was developed at Lund University and the very strict emission targets that were set up could be achieved, both in the laboratory tests and during the site-testing period. Typical performance and emission figures measured at the site installation are: Generator output (kW): 7,3; Hot water output (kW): 15; El. efficiency (%): 25,4; Total efficiency (%): 77,8; NO{sub x} (ppm): 14; CO (ppm): 112; HC (ppm): < 1; O{sub 2} (%): 8,0; Noise level 1 m from the unit (dBA): 83. The NO{sub x} emissions were reduced with almost 97 % as compared to a standard Stirling combustion system. The emission figures are considerably lower than what could be achieved in an internal combustion engine of similar size with an oxidation catalyst (report SGC 106), while the performance figures are similar for the two technologies. The site testing was carried out during a period of 1,5 year at a site owned by Goeteborg Energi. The site comprises a building structure with workshops, offices etc. covering a ground area of 2,500 m{sup 2}. A gas fired boiler with an output of 250 kW supplies hot water to a local grid for heating and tap water. The annual heat demand is typically 285 MWh and the hot water temperatures are normally 60-80 deg C. The site

A microeconomic analysis of decentralized small scale biomass based CHP plants—The case of Germany

International Nuclear Information System (INIS)

Wittmann, Nadine; Yildiz, Özgür

2013-01-01

Alternative energy sources, such as biomass CHP plants, have recently gained significantly in importance and action is due both on the large scale corporate level and on the small scale. Hence, making the scope and economic outline of such projects easily intelligible without losing relevant details seems a key factor to further promote the necessary developments. The model setup presented in this paper may therefore serve as a starting point for generating numerical results based on real life cases or scenarios. Its focus lies on the economic analysis of decentralized biomass CHP plants. It presents a new approach to analyzing the economic aspects of biomass CHP plants implementing a formal microeconomic approach. As Germany claims a leading role in the market for renewable energy production, the paper also takes a closer look on the effects of German energy policy with respect to biomass CHP plants. - Highlights: • A formal microeconomic model is used to analyse a decentralized biomass CHP plant. • Model setup is used to generate numerical results based on real life scenarios. • Nested CES production function is a new approach to model economics of biomass CHP. • Analysis presents insight into microeconomics and cost drivers of biomass CHP. • Evaluation of energy policy design with respect to environmental policy goals

Analysis of the location for peak heating in CHP based combined district heating systems

International Nuclear Information System (INIS)

Wang, Haichao; Lahdelma, Risto; Wang, Xin; Jiao, Wenling; Zhu, Chuanzhi; Zou, Pinghua

2015-01-01

Combined heat and power (CHP) is the main technology for providing the base load of district heating in China. However, CHP is not efficient for providing the peak load; instead, a peak boiler with high efficiency could be used to compensate the peak load. This paper studies how the location of the peak boiler can affect the energy efficiency and economic performance of such CHP based combined district heating system. Firstly, the connection mode and the control strategy for different peak heating locations are analyzed. Then the effect of the peak boiler's location on the initial investment of the network and the cost for distributing heat is studied. The objective is to place the peak boiler in a location where the overall costs are the smallest. Following this rule, the results indicate that the peak boiler should be located at the CHP plant if that allows using cheaper ‘self-use electricity’ in CHP for distributing the heat. However, if the market electricity price is used everywhere, or if energy efficiency is more emphasized, the location of the peak boiler should be closer to the users with dense heat loads. - Highlights: • Location for peak heating in the CHP based combined DH system is studied. • Regulation or control strategies for combined DH are summarized. • The heat load duration curve for combined DH is demonstrated. • Network design for combined DH with peak boiler outside of the CHP is analyzed

Dynamic analysis of PEMFC-based CHP systems for domestic application

International Nuclear Information System (INIS)

Barelli, L.; Bidini, G.; Gallorini, F.; Ottaviano, A.

2012-01-01

Highlights: ► Dynamic model of a CHP energy system based on a PEM fuel cell was developed. ► The CHP system behavior at variable electrical and thermal load was investigated. ► The optimal RH value was assessed maximizing PEMFC performance through simulations. ► The system best operating conditions are characterized by a RH value equal to 50%. -- Abstract: Fuel cell-based CHP systems for distributed residential power generation represent an interesting alternative to traditional thermoelectric plants. This is mainly due to the high efficiency obtainable in the production of electricity and heat in a decentralised, quiet and environmental friendly way. The current paper focuses on the development, in Matlab®Simulink environment, of a complete dynamic model of a residential cogenerative (CHP) energy system consisting of the Proton Exchange Membrane fuel cell (PEMFC), fuel processor, heat exchangers, humidifier and auxiliary hot water boiler. The target of the study is the investigation through such a model of the behavior of CHP systems based on fuel cell (FC) at variable electrical and thermal load, in reference to typical load curves of residential users. With the aim to evaluate the system performance (efficiency, fuel consumption, hot water production, response time) and then to characterize its better operating conditions with particular attention to air relative humidity, suitable simulations were carried out. They are characterized by the following of a typical electrical load trend and in relation to two different thermal load profiles. The dynamic model presented in this paper has allowed to observe the fully functioning of the FC based system under variable loads and it has permitted to design appropriate control logics for this system.

Risk analysis for CHP decision making within the conditions of an open electricity market

International Nuclear Information System (INIS)

Al-Mansour, Fouad; Kozuh, Mitja

2007-01-01

Decision making under uncertainty is a difficult task in most areas. Investment decisions for combined heat and power production (CHP) are certainly one of the areas where it is difficult to find an optimal solution since the payback period is several years and parameters change due to different perturbing factors of economic and mostly political nature. CHP is one of the most effective measures for saving primary energy and reduction of greenhouse gas emissions. The implementation of EU directives on the promotion of cogeneration based on useful heat demand in the internal energy market will accelerate CHP installation. The expected number of small CHP installations will be very high in the near future. A quick, reliable and simple tool for economic evaluation of small CHP systems is required. Since evaluation is normally made by sophisticated economic computer models which are rather expensive, a simple point estimate economic model was developed which was later upgraded by risk methodology to give more informative results for better decision making. This paper presents a reliable computer model entitled 'Computer program for economic evaluation analysis of CHP' as a tool for analysis and economic evaluation of small CHP systems with the aim of helping the decision maker. The paper describes two methods for calculation of the sensitivity of the economic results to changes of input parameters and the uncertainty of the results: the classic/static method and the risk method. The computer program uses risk methodology by applying RISK software on an existing conventional economic model. The use of risk methodology for economic evaluation can improve decisions by incorporating all possible information (knowledge), which cannot be done in the conventional economic model due to its limitations. The methodology was tested on the case of a CHP used in a smaller hospital

Annual energy balances of CHP-units supplying households; Jahresenergiebilanzen von KWK-Anlagen zur Hausenergieversorgung

Energy Technology Data Exchange (ETDEWEB)

Geiger, B.; Muehlbacher, H. [Technische Univ. Muenchen (Germany). Lehrstuhl fuer Energiewirtschaft und Anwendungstechnik

2008-07-01

A method to balance CHP-units for use in households on an annual basis has been developed. Seasonal as well as intraday fluctuations of the CHP-units are accounted for in the model. The results of this new method were validated in a test facility for certain days. Together with experimentally obtained data from a CHP-unit, the potential for technical improvements and a more favourable operational mode can be derived from the model. (orig.)

Alternative depreciation policies for promoting combined heat and power (CHP) development in Brazil

International Nuclear Information System (INIS)

Soares, Jeferson Borghetti; Szklo, Alexandre Salem; Tolmasquim, Mauricio Tiomno

2006-01-01

This paper assessed the economic impact of alternative depreciation methods on the development of combined heat-and-power (CHP) systems in the Brazilian industrial sector. Alternative depreciation methods were proposed and the case study of a Brazilian chemical plant showed that the most effective depreciation method for the promotion of CHP plants in Brazil was the Matheson method with an accelerated depreciation schedule of 7 years. This alternative method was then applied to the Brazilian chemical industry as a whole, increasing its installed capacity in CHP systems by 24%. Therefore, fiscal incentives can be an interesting tool for promoting energy efficiency in the Brazilian industrial sector, promoting the expansion of CHP plants. It reduces government fiscal revenues, but it also induces the technological reposition and improves the feasibility of ventures that are not installed without this kind of incentive

Local CHP Plants between the Natural Gas and Electricity Systems

DEFF Research Database (Denmark)

Bregnbæk, Lars; Schaumburg-Müller, Camilla

2005-01-01

, and they contribute significantly to the electricity production. CHP is, together with the wind power, the almost exclusive distributed generation in Denmark. This paper deals with the CHP as intermediary between the natural gas system and the electricity system. In particular, the relationship between the peak hour......Local combined heat and power (CHP) plants in Denmark constitute an important part of the national energy conversion capacity. In particular they supply a large share of the district heating networks with heat. At the same time they are important consumers as seen from the gas network system...... characteristics of the electricity and gas systems will be investigated. The point is here that the two systems will tend to have peak demand during the same hours. This is the typical situation, since load is high during the same hours of the day and of the year. Moreover, the random variations in the load...

Procuring Stationary Fuel Cells For CHP: A Guide for Federal Facility Decision Makers

Energy Technology Data Exchange (ETDEWEB)

Stinton, David P [ORNL; McGervey, Joseph [SRA International, Inc.; Curran, Scott [ORNL

2011-11-01

Federal agency leaders are expressing growing interest in using innovative fuel cell combined heat and power (CHP) technology at their sites, motivated by both executive branch sustainability targets and a desire to lead by example in the transition to a clean energy economy. Fuel cell CHP can deliver reliable electricity and heat with 70% to 85% efficiency. Implementing this technology can be a high efficiency, clean energy solution for agencies striving to meet ambitious sustainability requirements with limited budgets. Fuel cell CHP systems can use natural gas or renewable fuels, such as biogas. Procuring Stationary Fuel Cells for CHP: A Guide for Federal Facility Decision Makers presents an overview of the process for planning and implementing a fuel cell CHP project in a concise, step-by-step format. This guide is designed to help agency leaders turn their interest in fuel cell technology into successful installations. This guide concentrates on larger (100 kW and greater) fuel cell CHP systems and does not consider other fuel cell applications such as cars, forklifts, backup power supplies or small generators (<100 kW). Because fuel cell technologies are rapidly evolving and have high up front costs, their deployment poses unique challenges. The electrical and thermal output of the CHP system must be integrated with the building s energy systems. Innovative financing mechanisms allow agencies to make a make versus buy decision to maximize savings. This guide outlines methods that federal agencies may use to procure fuel cell CHP systems with little or no capital investment. Each agency and division, however, has its own set of procurement procedures. This guide was written as a starting point, and it defers to the reader s set of rules if differences exist. The fuel cell industry is maturing, and project developers are gaining experience in working with federal agencies. Technology improvements, cost reductions, and experienced project developers are making

Design of Biomass Combined Heat and Power (CHP Systems based on Economic Risk using Minimax Regret Criterion

Directory of Open Access Journals (Sweden)

Ling Wen Choong

2018-01-01

Full Text Available It is a great challenge to identify optimum technologies for CHP systems that utilise biomass and convert it into heat and power. In this respect, industry decision makers are lacking in confidence to invest in biomass CHP due to economic risk from varying energy demand. This research work presents a linear programming systematic framework to design biomass CHP system based on potential loss of profit due to varying energy demand. Minimax Regret Criterion (MRC approach was used to assess maximum regret between selections of the given biomass CHP design based on energy demand. Based on this, the model determined an optimal biomass CHP design with minimum regret in economic opportunity. As Feed-in Tariff (FiT rates affects the revenue of the CHP plant, sensitivity analysis was then performed on FiT rates on the selection of biomass CHP design. Besides, design analysis on the trend of the optimum design selected by model was conducted. To demonstrate the proposed framework in this research, a case study was solved using the proposed approach. The case study focused on designing a biomass CHP system for a palm oil mill (POM due to large energy potential of oil palm biomass in Malaysia.

Network Capacity Assessment of CHP-based Distributed Generation on Urban Energy Distribution Networks

Science.gov (United States)

Zhang, Xianjun

The combined heat and power (CHP)-based distributed generation (DG) or dis-tributed energy resources (DERs) are mature options available in the present energy market, considered to be an effective solution to promote energy efficiency. In the urban environment, the electricity, water and natural gas distribution networks are becoming increasingly interconnected with the growing penetration of the CHP-based DG. Subsequently, this emerging interdependence leads to new topics meriting serious consideration: how much of the CHP-based DG can be accommodated and where to locate these DERs, and given preexisting constraints, how to quantify the mutual impacts on operation performances between these urban energy distribution networks and the CHP-based DG. The early research work was conducted to investigate the feasibility and design methods for one residential microgrid system based on existing electricity, water and gas infrastructures of a residential community, mainly focusing on the economic planning. However, this proposed design method cannot determine the optimal DG sizing and siting for a larger test bed with the given information of energy infrastructures. In this context, a more systematic as well as generalized approach should be developed to solve these problems. In the later study, the model architecture that integrates urban electricity, water and gas distribution networks, and the CHP-based DG system was developed. The proposed approach addressed the challenge of identifying the optimal sizing and siting of the CHP-based DG on these urban energy networks and the mutual impacts on operation performances were also quantified. For this study, the overall objective is to maximize the electrical output and recovered thermal output of the CHP-based DG units. The electricity, gas, and water system models were developed individually and coupled by the developed CHP-based DG system model. The resultant integrated system model is used to constrain the DG's electrical

An updated assessment of the prospects for fuel cells in stationary power and CHP. An information paper

Energy Technology Data Exchange (ETDEWEB)

Sanderson, T.K. [Future Energy Solutions, Harwell (United Kingdom)

2005-07-01

This report presents updated conclusions of the Department of Trade and Industry's research and development programme to assess the commercial prospects for advanced fuel cells in stationary power and combined heat and power (CHP) systems. The programme has focussed on low temperature solid polymer fuel cells (SPFCs) for transport and combined heat and power (CHP)/distributed power and high temperature solid oxide fuel cells (SOFCs) for CHP/distributed power. As well as assessing the prospects for SPFCs and SOFCs in stationary power and CHP applications, the report examines those for molten carbonate fuel cells (MCFCs) and phosphoric acid fuel cells (PAFCs). The report provides an assessment of the status of technology development for these different types of fuel cells in terms of applications to stationary power and CHP, and offers estimates of market potential for SOFCs in CHP markets, SPFCs in CHP markets and SOFCs in distributed power generation markets. Both large SPFC and SOFC CHP systems require further development to deliver the necessary cost reductions in materials and manufacturing processes before pre-commercial sales can begin. The routes taken by different manufacturers and their choice of preferred technology are explained. A discussion of the prospects and barriers for fuel cell cars concludes that while cost reduction is a major barrier to the successful commercialisation of fuel cells, there are insufficient data available from operating fuel cells systems (other than PAFC) in stationary power and CHP applications to assess the economic attractiveness of fuel cells compared with existing systems. More field trials are required to confirm energy and environmental performance in such applications and to evaluate operational and economic performance under commercial operating conditions. Such field trials could also provide a focus for the required developments in fuel cells for stationary power/CHP systems.

Modeling work of a small scale gasifier/SOFC CHP system

Energy Technology Data Exchange (ETDEWEB)

Liu, M.; Aravind, P.V.; Qu, Z.; Woudstra, N.; Verkooijen, A.H.M. [Delft University of Technology (Netherlands). Dept. of Mechanical Engineering], Emails: ming.liu@tudelft.nl, p.v.aravind@tudelft.nl, z.qu@tudelft.nl, n.woudstra@tudelft.nl, a. h. m. verkooijen@tudelft.nl; Cobas, V.R.M. [Federal University of Itajuba (UNIFEI), Pinheirinhos, MG (Brazil). Dept. of Mechanical Engineering], E-mail: vlad@unifei.edu.br

2009-07-01

For a highly efficient biomass gasification/Solid Oxide Fuel Cell (SOFC) Combined Heat and Power (CHP) generation system, the gasifier, the accompanying gas cleaning technologies and the CHP unit must be carefully designed as an integrated unit. This paper describes such a system involving a two-stage fixed-bed down draft gasifier, a SOFC CHP unit and a gas cleaning system. A gas cleaning system with both low temperature and high temperature sections is proposed for coupling the gasifier and the SOFC. Thermodynamic modeling was carried out for the gasifier/SOFC system with the proposed gas cleaning system. The net AC electrical efficiency of this system is around 30% and the overall system efficiency is around 60%. This paper also describes various exergy losses in the system and the future plans for integrated gasifier-GCU-SOFC experiments from which the results will be used to validate the modeling results of this system. (author)

Combustion Turbine CHP System for Food Processing Industry

Energy Technology Data Exchange (ETDEWEB)

None

2010-10-01

This factsheet describes a combined heat and power (CHP) demonstration project that reduces the energy costs and environmental impact of a plant while easing congestion on the constrained Northeast power grid.

Development of Next Generation micro-CHP System

DEFF Research Database (Denmark)

Arsalis, Alexandros

Novel proposals for the modeling and operation of a micro-CHP (combined-heat-andpower) residential system based on HT-PEMFC (High Temperature-Proton Exchange Membrane Fuel Cell) technology are described and analyzed to investigate the technical feasibility of such systems. The proposed systems must...

Optimal design of CHP-based microgrids: Multiobjective optimisation and life cycle assessment

International Nuclear Information System (INIS)

Zhang, Di; Evangelisti, Sara; Lettieri, Paola; Papageorgiou, Lazaros G.

2015-01-01

As an alternative to current centralised energy generation systems, microgrids are adopted to provide local energy with lower energy expenses and gas emissions by utilising distributed energy resources (DER). Several micro combined heat and power technologies have been developed recently for applications at domestic scale. The optimal design of DERs within CHP-based microgrids plays an important role in promoting the penetration of microgrid systems. In this work, the optimal design of microgrids with CHP units is addressed by coupling environmental and economic sustainability in a multi-objective optimisation model which integrates the results of a life cycle assessment of the microgrids investigated. The results show that the installation of multiple CHP technologies has a lower cost with higher environmental saving compared with the case when only a single technology is installed in each site, meaning that the microgrid works in a more efficient way when multiple technologies are selected. In general, proton exchange membrane (PEM) fuel cells are chosen as the basic CHP technology for most solutions, which offers lower environmental impacts at low cost. However, internal combustions engines (ICE) and Stirling engines (SE) are preferred if the heat demand is high. - Highlights: • Optimal design of microgrids is addressed by coupling environmental and economic aspects. • An MILP model is formulated based on the ε-constraint method. • The model selects a combination of CHP technologies with different technical characteristics for optimum scenarios. • The global warming potential (GWP) and the acidification potential (AP) are determined. • The output of LCA is used as an input for the optimisation model

A family of serine proteases of Clavibacter michiganensis subsp. michiganensis: chpC plays a role in colonization of the host plant tomato.

Science.gov (United States)

Stork, Ines; Gartemann, Karl-Heinz; Burger, Annette; Eichenlaub, Rudolf

2008-09-01

Genes for seven putative serine proteases (ChpA-ChpG) belonging to the trypsin subfamily and homologous to the virulence factor pat-1 were identified on the chromosome of Clavibacter michiganensis subsp. michiganensis (Cmm) NCPPB382. All proteases have signal peptides indicating export of these proteins. Their putative function is suggested by two motifs and an aspartate residue typical for serine proteases. Furthermore, six cysteine residues are located at conserved positions. The genes are clustered in a chromosomal region of about 50 kb with a significantly lower G + C content than common for Cmm. The genes chpA, chpB and chpD are pseudogenes as they contain frame shifts and/or in-frame stop codons. The genes chpC and chpG were inactivated by the insertion of an antibiotic resistance cassette. The chpG mutant was not impaired in virulence. However, in planta the titre of the chpC mutant was drastically reduced and only weak disease symptoms were observed. Complementation of the chpC mutant by the wild-type allele restored full virulence. ChpC is the first chromosomal gene of Cmm identified so far that affects the interaction of the pathogen with the host plant.

ChpK and MazF of the toxin-antitoxin modules are involved in the virulence of Leptospira interrogans during infection.

Science.gov (United States)

Komi, Komi Koukoura; Ge, Yu-Mei; Xin, Xiao-Yang; Ojcius, David M; Sun, Dexter; Hu, Wei-Lin; Zhao, Xin; Lin, Xu'ai; Yan, Jie

2015-01-01

Pathogenic Leptospira species are the causative agents of leptospirosis, a global zoonotic infectious disease. Toxin-antitoxin (TA) modules have been confirmed as stress-response elements that induce prokaryotic and eukaryotic cell-growth arrest or death, but their role in the virulence of Leptospira has not been reported. Here, we confirmed that all the tested leptospiral strains had the chpIK and mazEF TA modules with highly-conserved sequences. The transcription and expression of the chpI, chpK, mazE, and mazF genes of Leptospira interrogans strain Lai were significantly increased during infection of phorbol 12-myristate 13-acetate-induced human THP-1 macrophages. The toxic ChpK and MazF but not the antitoxic ChpI and MazE proteins were detectable in the cytoplasmic fraction of leptospire-infected THP-1 cells, indicating the external secretion of ChpK and MazF during infection. Transfection of the chpK or mazF gene caused decreased viability and necrosis in THP-1 cells, whereas the chpI or mazE gene transfection did not affect the viability of THP-1 cells but blocked the ChpK or MazF-induced toxicity. Deletion of the chpK or mazF gene also decreased the late-apoptotic and/or necrotic ratios of THP-1 cells at the late stages of infection. The recombinant protein MazF (rMazF) cleaved the RNAs but not the DNAs from Leptospira and THP-1 cells, and this RNA cleavage was blocked by rMazE. However, the rChpK had no RNA or DNA-degrading activity. All these findings indicate that the ChpK and MazF proteins in TA modules are involved in the virulence of L. interrogans during infection. Copyright © 2014 Institut Pasteur. Published by Elsevier Masson SAS. All rights reserved.

Modeling and simulation of a residential micro-CHP system based on HT-PEMFC technology

DEFF Research Database (Denmark)

Arsalis, Alexandros; Nielsen, Mads Pagh; Kær, Søren Knudsen

2009-01-01

Combined-heat-and-power (CHP) technology is a well known and proved method to produce simultaneously power and heat at high efficiencies. This can be further improved by the introduction of a novel micro-CHP residential system based on High Temperature-Proton Exchange Membrane Fuel Cell (HT-PEMFC......). The HT-PEMFC (based on PBI-membrane technology) operates at temperatures near 200oC, and this can be an ideal match for cogeneration residential systems. The proposed system provides electric power, hot water, and space heating for a typical household (1-5 kWe, 5-10 kWth). The micro-CHP system...

A Study of a Diesel Engine Based Micro-CHP System

Energy Technology Data Exchange (ETDEWEB)

Krishna, C.R.; Andrews, J.; Tutu, N.; Butcher, T.

2010-08-31

This project, funded by New York State Energy Research and Development Agency (NYSERDA), investigated the potential for an oil-fired combined heat and power system (micro-CHP system) for potential use in residences that use oil to heat their homes. Obviously, this requires the power source to be one that uses heating oil (diesel). The work consisted of an experimental study using a diesel engine and an analytical study that examined potential energy savings and benefits of micro-CHP systems for 'typical' locations in New York State. A search for a small diesel engine disclosed that no such engines were manufactured in the U.S. A single cylinder engine manufactured in Germany driving an electric generator was purchased for the experimental work. The engine was tested using on-road diesel fuel (15 ppm sulfur), and biodiesel blends. One of the main objectives was to demonstrate the possibility of operation in the so-called HCCI (Homogeneous Charge Compression Ignition) mode. The HCCI mode of operation of engines is being explored as a way to reduce the emission of smoke, and NOx significantly without exhaust treatment. This is being done primarily in the context of engines used in transportation applications. However, it is felt that in a micro-CHP application using a single cylinder engine, such an approach would confer those emission benefits and would be much easier to implement. This was demonstrated successfully by injecting the fuel into the engine air intake using a heated atomizer made by Econox Technologies LLC to promote significant vaporization before entering the cylinder. Efficiency and emission measurements were made under different electrical loads provided by two space heaters connected to the generator in normal and HCCI modes of operation. The goals of the analytical work were to characterize, from the published literature, the prime-movers for micro-CHP applications, quantify parametrically the expected energy savings of using micro-CHP

Increased power to heat ratio of small scale CHP plants using biomass fuels and natural gas

International Nuclear Information System (INIS)

Savola, Tuula; Fogelholm, Carl-Johan

2006-01-01

In this paper, we present a systematic study of process changes for increased power production in 1-20 MW e combined heat and power (CHP) plants. The changes are simulated, and their economic feasibility evaluated by using existing small scale CHP case plants. Increasing power production in decentralised CHP plants that operate according to a certain heat demand could reduce the fuel consumption and CO 2 emissions per power unit produced and improve the feasibility of CHP plant investments. The CHP plant process changes were simulated under design and off design conditions and an analysis of power and heat production, investment costs and CO 2 emissions was performed over the whole annual heat demand. The results show that using biomass fuels, there are profitable possibilities to increase the current power to heat ratios, 0.23-0.48, of the small scale CHP plants up to 0.26-0.56, depending on the size of the plant. The profitable changes were a two stage district heat exchanger and the addition of a steam reheater and a feed water preheater. If natural gas is used as an additional fuel, the power to heat ratio may be increased up to 0.35-0.65 by integrating a gas engine into the process. If the CO 2 savings from the changes are also taken into account, the economic feasibility of the changes increases. The results of this work offer useful performance simulation and investment cost knowledge for the development of more efficient and economically feasible small scale CHP processes

CHP in Switzerland from 1990 to 1998. Thermal power generation including combined heat and power

International Nuclear Information System (INIS)

Kaufmann, U.

1999-01-01

The results of a study on thermal power generation in Switzerland show that combined heat and power (CHP) systems have grown rapidly. Statistics are presented on the development of CHP-based power and also on thermal power stations without waste heat usage. Figures are given for gas and steam turbine installations, combined gas and steam turbine stations and motor-driven CHP units. Power production is categorised, separating small and large (over 1 Megawatt electrical) power generation facilities. On-site, distributed power generation at consumers' premises and the geographical distribution of plant is described

Reactive power control with CHP plants - A demonstration

DEFF Research Database (Denmark)

Nyeng, Preben; Østergaard, Jacob; Andersen, Claus A.

2010-01-01

power rating of 7.3 MW on two synchronous generators. A closed-loop control is implemented, that remote controls the CHP plant to achieve a certain reactive power flow in a near-by substation. The solution communicates with the grid operator’s existing SCADA system to obtain measurements from...... lines to underground cables has changed the reactive power balance, and third, the TSO has introduced restrictions in the allowed exchange of reactive power between the transmission system and distribution grids (known as the Mvar-arrangement). The demonstration includes a CHP plant with an electric......In this project the potential for ancillary services provision by distributed energy resources is investigated. Specifically, the provision of reactive power control by combined heat and power plants is examined, and the application of the new standard for DER communication systems, IEC 61850...

Experimental development, 1D CFD simulation and energetic analysis of a 15 kw micro-CHP unit based on reciprocating internal combustion engine

International Nuclear Information System (INIS)

Muccillo, M.; Gimelli, A.

2014-01-01

Cogeneration is commonly recognized as one of the most effective solutions to achieve the increasingly stringent reduction in primary energy consumption and greenhouse emissions. This characteristic led to the adoption of specific directives promoting this technique. In addition, a strategic role in power reliability is recognized to distributed generation. The study and prototyping of cogeneration plants, therefore, has involved many research centres. This paper deals with energetic aspects of CHP referring to the study of a 15 kW micro-CHP plant based on a LPG reciprocating engine designed, built and grid connected. The plant consists of a heat recovery system characterized by a single water circuit recovering heat from exhaust gases, from engine coolant and from the energy radiated by the engine within the shell hosting the plant. Some tests were carried out at whole open throttle and the experimental data were collected. However it was needed to perform a 1D thermo-fluid dynamics simulation of the engine to completely characterize the micro-CHP. As the heat actually recovered depends on the user's thermal load, particularly from the required temperature's level, a comparison of the results for six types of users were performed: residential, hospital, office, commercial, sports, hotel. Both Italian legislative indexes IRE and LT were evaluated, as defined by A.E.E.G resolution n. 42/02 and subsequent updates, as well as the plant's total Primary Energy Saving. - Highlights: • This paper deals with energetic aspects of CHP referring to the study of a 15 kW micro-CHP plant. • The 15 kW micro-CHP plant is based on a GPL reciprocating engine designed, built and grid connected. • Some tests were carried out at whole open throttle and the experimental data were collected. • It was needed to perform a 1D thermo-fluid dynamics simulation of the engine to completely characterize the micro-CHP. • The analysed solution is particularly suited for

The Pseudomonas aeruginosa Chp Chemosensory System Regulates Intracellular cAMP Levels by Modulating Adenylate Cyclase Activity

Science.gov (United States)

Fulcher, Nanette B.; Holliday, Phillip M.; Klem, Erich; Cann, Martin J.; Wolfgang, Matthew C.

2010-01-01

Summary Multiple virulence systems in the opportunistic pathogen Pseudomonas aeruginosa are regulated by the second messenger signaling molecule adenosine 3’, 5’-cyclic monophosphate (cAMP). Production of cAMP by the putative adenylate cyclase enzyme CyaB represents a critical control point for virulence gene regulation. To identify regulators of CyaB, we screened a transposon insertion library for mutants with reduced intracellular cAMP. The majority of insertions resulting in reduced cAMP mapped to the Chp gene cluster encoding a putative chemotaxis-like chemosensory system. Further genetic analysis of the Chp system revealed that it has both positive and negative effects on intracellular cAMP and that it regulates cAMP levels by modulating CyaB activity. The Chp system was previously implicated in the production and function of type IV pili (TFP). Given that cAMP and the cAMP-dependent transcriptional regulator Vfr control TFP biogenesis gene expression, we explored the relationship between cAMP, the Chp system and TFP regulation. We discovered that the Chp system controls TFP production through modulation of cAMP while control of TFP-dependent twitching motility is cAMP-independent. Overall, our data define a novel function for a chemotaxis-like system in controlling cAMP production and establish a regulatory link between the Chp system, TFP and other cAMP-dependent virulence systems. PMID:20345659

Changes of the thermodynamic parameters in failure conditions of the micro-CHP cycle

Science.gov (United States)

Matysko, Robert; Mikielewicz, Jarosław; Ihnatowicz, Eugeniusz

2014-03-01

The paper presents the calculations for the failure conditions of the ORC (organic Rankine cycle) cycle in the electrical power system. It analyses the possible reasons of breakdown, such as the electrical power loss or the automatic safety valve failure. The micro-CHP (combined heat and power) system should have maintenance-free configuration, which means that the user does not have to be acquainted with all the details of the ORC system operation. However, the system should always be equipped with the safety control systems allowing for the immediate turn off of the ORC cycle in case of any failure. In case of emergency, the control system should take over the safety tasks and protect the micro-CHP system from damaging. Although, the control systems are able to respond quickly to the CHP system equipped with the inertial systems, the negative effects of failure are unavoidable and always remain for some time. Moreover, the paper presents the results of calculations determining the inertia for the micro-CHP system of the circulating ORC pump, heat removal pump (cooling condenser) and the heat supply pump in failure conditions.

Changes of the thermodynamic parameters in failure conditions of the micro-CHP cycle

Directory of Open Access Journals (Sweden)

Matysko Robert

2014-03-01

Full Text Available The paper presents the calculations for the failure conditions of the ORC (organic Rankine cycle cycle in the electrical power system. It analyses the possible reasons of breakdown, such as the electrical power loss or the automatic safety valve failure. The micro-CHP (combined heat and power system should have maintenance-free configuration, which means that the user does not have to be acquainted with all the details of the ORC system operation. However, the system should always be equipped with the safety control systems allowing for the immediate turn off of the ORC cycle in case of any failure. In case of emergency, the control system should take over the safety tasks and protect the micro-CHP system from damaging. Although, the control systems are able to respond quickly to the CHP system equipped with the inertial systems, the negative effects of failure are unavoidable and always remain for some time. Moreover, the paper presents the results of calculations determining the inertia for the micro-CHP system of the circulating ORC pump, heat removal pump (cooling condenser and the heat supply pump in failure conditions.

Utilization of straw in district heating and CHP plants

International Nuclear Information System (INIS)

Nikolaisen, L.

1993-01-01

In Denmark 64 straw-fired district heating plants and 6 decentral CHP plants have been built since 1980 which are completely or partly straw-fired. The annual straw consumption in the district heating plants is 275,000 tons and in the decentral plants about 200,000 tons. The size of the district heating plants amounts to 0.5 MW - 10 MW and that of the CHP plants to 7 MW - 67 MW heat flow rate. Either whole bales or cut/scarified straw is used for firing. Hesston bales of about 450 kg control the market. The Centre of Biomass Technology is an activity supported 100 % by the Danish Energy Agency with the purpose of increasing the use of straw and wood in the energy supply (orig.)

Environmental sustainability analysis of UK whole-wheat bioethanol and CHP systems

International Nuclear Information System (INIS)

Martinez-Hernandez, Elias; Ibrahim, Muhammad H.; Leach, Matthew; Sinclair, Phillip; Campbell, Grant M.; Sadhukhan, Jhuma

2013-01-01

The UK whole-wheat bioethanol and straw and DDGS-based combined heat and power (CHP) generation systems were assessed for environmental sustainability using a range of impact categories or characterisations (IC): cumulative primary fossil energy (CPE), land use, life cycle global warming potential over 100 years (GWP 100 ), acidification potential (AP), eutrophication potential (EP) and abiotic resources use (ARU). The European Union (EU) Renewable Energy Directive's target of greenhouse gas (GHG) emission saving of 60% in comparison to an equivalent fossil-based system by 2020 seems to be very challenging for stand-alone wheat bioethanol system. However, the whole-wheat integrated system, wherein the CHP from the excess straw grown in the same season and from the same land is utilised in the wheat bioethanol plant, can be demonstrated for potential sustainability improvement, achieving 85% emission reduction and 97% CPE saving compared to reference fossil systems. The net bioenergy from this system and from 172,370 ha of grade 3 land is 12.1 PJ y −1 providing land to energy yield of 70 GJ ha −1 y −1 . The use of DDGS as an animal feed replacing soy meal incurs environmental emission credit, whilst its use in heat or CHP generation saves CPE. The hot spots in whole system identified under each impact category are as follows: bioethanol plant and wheat cultivation for CPE (50% and 48%), as well as for ARU (46% and 52%). EP and GWP 100 are distributed among wheat cultivation (49% and 37%), CHP plant (26% and 30%) and bioethanol plant (25%, and 33%), respectively. -- Highlights: ► UK whole-wheat energy system can achieve 85% GHG emission reduction. ► UK whole-wheat energy system can achieve 97% primary energy saving. ► The land to energy yield of the UK whole-wheat system is 70 GJ ha −1 y −1 . ► Fertiliser production is the hotspot. ► DDGS and straw-based CHP system integration to wheat bioethanol is feasible

Elimination of restraints on the propagation of combined heat and power (CHP) generation systems in Switzerland

International Nuclear Information System (INIS)

Rieder, S.; Landis, F.; Lienhard, A.; Marti Locher, F.; Krummenacher, S.

2009-04-01

This report for the Swiss Federal Office of Energy (SFOE) discusses the results of study initiated by the SFOE that was to investigate the reasons for the low level of proliferation of CHP technology in Switzerland. The two main questions asked - which factors inhibit the use of CHP in particular application areas and which energy-policy measures can remove such obstacles - are discussed. The use of CHP in various areas of application from waste incineration plants through to units used in residential buildings is analysed and commented on. Recommendations on measures that can be taken to enhance the use of CHP are discussed. Three strategy variants available to the public services area are presented and discussed. It is noted that a consensus between players in the technical and political areas is necessary

Techno, Economic and Environmental Assessment of a Combined Heat and Power (CHP System—A Case Study for a University Campus

Directory of Open Access Journals (Sweden)

Khuram Pervez Amber

2018-05-01

Full Text Available Universities in the United Kingdom that have installed Combined Heat and Power (CHP technology are making good moves towards achieving their CO2 reduction targets. However, CHP may not always be an economical option for a university campus due to numerous factors. Identification of such factors is highly important before making an investment decision. A detailed technical, economic, and environmental feasibility of CHP is, therefore, indispensable. This study aims to undertake a detailed assessment of CHP for a typical university campus and attempts to highlight the significance of such factors. Necessary data and information were collected through site visits, whereas the CHP sizing was performed using the London South Bank University (LSBU CHP model. The results suggest that there is a strong opportunity of installing a 230 kW CHP that will offset grid electricity and boilers thermal supply by 47% and 75%, respectively, and will generate financial and environmental yearly savings of £51k and 395 t/CO2, respectively. A wider spark gap decreases the payback period of the project and vice versa. The capital cost of the project could affect the project’s economics due to factors, such as unavailability of space for CHP, complex existing infrastructure, and unavailability of a gas connection.

CHP expansion strategy in North Rhine-Westphalia. A blueprint for other regions; KWK-Ausbaustrategie in NRW. Eine Blaupause fuer andere Regionen

Energy Technology Data Exchange (ETDEWEB)

Holzapfel, Dominik [EnergieAgentur.NRW, Duesseldorf (Germany); Schneider, Sabine [EnergieAgentur.NRW, Wuppertal (Germany)

2015-10-01

The North Rhine-Westphalian state government intends to increase the share of combined heat and power (CHP) generation to at least 25 % by 2020. Since 2013, the campaign ''CHP.NRW - Power Meets Heat'' (''KWK.NRW - Strom trifft Waerme'') of the EnergyAgency.NRW, is has been running on behalf of the NRW Climate Protection Ministry, to publicise this technology and to promote its expansion. The campaign accompanies the State Government's CHP Stimulus Programme. The EnergyAgency.NRW has organised companies and research institutions, associations and interest groups under the umbrella of ''CHP.NRW - Power Meets Heat'', aiming at co-ordinated and intensified activities in the field of combined heat and power generation. The target of the initial-project ''roadmap/CHP.NRW'' of the ''Virtual Institute / CHP.NRW'' is to develop a guideline for the application and optimisation of CHP-systems.

Comparative analysis of organizational obstacles to CHP/DH

Energy Technology Data Exchange (ETDEWEB)

Ruedig, W.

1986-04-01

An explanation is given of the vast differences between the countries of Western Europe in the adoption of combined heat and power (CHP) for district heating (DH). The history of this technology in FR Germany and the UK is analysed in detail, and experiences of other countries are reviewed. It is concluded that the over centralization of the electricity supply industry is a major obstacle in the widespread adoption of combined heat and power and district heating. Significant improvements of energy efficiency would thus require organizational reforms giving greater powers to local energy organizations. This, however, should not imply total decentralization of energy supply. Instead, a two-tier system is proposed in which central organizations remain responsible for bulk supply but where local or regional bodies are in charge of all gas, electricity and heat supplies to the final user.

Contribution of wind power and CHP to exports from Western Denmark during 2000-2004

International Nuclear Information System (INIS)

Mignard, D.; Harrison, G.P.; Pritchard, C.L.

2007-01-01

The experience of Denmark is used by the United Kingdom's anti-wind lobby to demonstrate that intermittency and inaccuracies in wind forecasting make wind power ineffective and expensive. A further assertion is that most of the power is 'unwanted' since up to 80% of it is exported. Here, available data for Danish energy production for 2000-2004 is used to assess the link between wind generation and exports and test the validity of these claims. Net exports in Western Denmark showed good correlation with wind production. However, they were more significantly correlated with the production from local combined heat and power (CHP) plants. In order to test the 80% export claim, a simple technique was devised to correlate and rank hourly net exports and generation from wind and local CHP. In the case where net exports were primarily attributed to (or blamed on) wind, 44-84% of annual wind production was deemed to be exported, with wind 'causing' 57-79% of net annual exports. For this extreme scenario, the percentage values are in line with those of critics. However, under the opposite extreme scenario in which exports are attributed to local CHP, 77-94% of exports were caused by CHP and only 4-32% of wind production was exported. Overall, this study shows that there is some degree of correlation between net exports and wind power, but that the claim that 80% is exported is unwarranted since it ignores the demonstrably stronger influence of local CHP. (author)

Ecological assessment of new CHP systems and their combination; Oekologische Bewertung neuer WKK-Systeme und Systemkombinationen - Schlussbericht

Energy Technology Data Exchange (ETDEWEB)

Primas, A.

2007-07-01

This final report for the Swiss Federal Office of Energy (SFOE) reports on new developments in the Combined Heat and Power (CHP) generation area. The objective of this study is an ecological and technical evaluation of various CHP systems and system combinations. These also include suitable combinations with other technologies. Systems for five different temperature levels are quantified according to their environmental impact. Various possible applications are compared with a highly efficient reference system using separate heat and power generation - a combined-cycle plant and a heat pump. For chilled water production a combination of the CHP system with an absorption chiller is investigated. The results of the investigations are presented and commented on. Also, advantageous applications of CHP systems are noted.

Micro scale CHP based on biomass intelligent heat transfer with thermoelectric generators

Energy Technology Data Exchange (ETDEWEB)

Moser, W.; Aigenbauer, S.; Heckmann, M.; Friedl, G. (Austrian Bioenergy Centre GmbH, Wieselburg (Austria)); Hofbauer, H. (Institute of Chemical Engineering, Vienna University of Technology (Austria))

2007-07-01

Pellet burners need auxiliary electrical power to provide CO{sub 2} balanced heat in a comfortable and environment friendly way. The idea is to produce this and some extra electricity within the device in order to save resources and to gain operation reliability and independency. An option for micro scale CHP is the usage of thermoelectric generators (TEGs). They allow direct conversion of heat into electrical power. They have the advantage of a long maintenance free durability and noiseless operation without moving parts or any working fluid. The useful heat remains almost unaffected and can still be used for heating. TEGs are predestined for the use in micro scale CHP based on solid biomass. In this paper the first results from the fully integrated prototype are presented. The performance of the TEG was observed for different loads and operating conditions in order to realise an optimised micro scale CHP based on solid biomass. (orig.)

Research, Development and Demonstration of Micro-CHP System for Residential Applications

Energy Technology Data Exchange (ETDEWEB)

Karl Mayer

2010-03-31

ECR International and its joint venture company, Climate Energy, are at the forefront of the effort to deliver residential-scale combined heat and power (Micro-CHP) products to the USA market. Part of this substantial program is focused on the development of a new class of steam expanders that offers the potential for significantly lower costs for small-scale power generation technology. The heart of this technology is the scroll expander, a machine that has revolutionized the HVAC refrigerant compressor industry in the last 15 years. The liquid injected cogeneration (LIC) technology is at the core of the efforts described in this report, and remains an excellent option for low cost Micro-CHP systems. ECR has demonstrated in several prototype appliances that the concept for LIC can be made into a practical product. The continuing challenge is to identify economical scroll machine designs that will meet the performance and endurance requirements needed for a long life appliance application. This report describes the numerous advances made in this endeavor by ECR International. Several important advances are described in this report. Section 4 describes a marketing and economics study that integrates the technical performance of the LIC system with real-world climatic data and economic analysis to assess the practical impact that different factors have on the economic application of Micro-CHP in residential applications. Advances in the development of a working scroll steam expander are discussed in Section 5. A rigorous analytical assessment of the performance of scroll expanders, including the difficult to characterize impact of pocket to pocket flank leakage, is presented in Section 5.1. This is followed with an FEA study of the thermal and pressure induced deflections that would result from the normal operation of an advanced scroll expander. Section 6 describes the different scroll expanders and test fixtures developed during this effort. Another key technical

Optimal designs of small CHP plants in a market with fluctuating electricity prices

DEFF Research Database (Denmark)

Lund, Henrik; Andersen, A.N.

2005-01-01

The paper presents the Danish experince with methodologies and software tools, which have been used to design investment and operation strategies for almost all small CHP plants in Denmark during the decade of the triple tariff.......The paper presents the Danish experince with methodologies and software tools, which have been used to design investment and operation strategies for almost all small CHP plants in Denmark during the decade of the triple tariff....

A CSP plant combined with biomass CHP using ORC-technology in Bronderslev Denmark

DEFF Research Database (Denmark)

Perers, Bengt; Furbo, Simon; Yuan, Guofeng

2017-01-01

A new CSP plant combined with biomass CHP, using ORC technology, will be built and taken into operation in Bronderslev, Denmark during spring 2017. The price for Biomass is expected to increase with more and more use of this very limited energy source and then CSP will be cost effective in the long...... run, also in the Danish climate. Oil is used as heat transfer fluid instead of steam giving several advantages in this application for district heating at high latitudes. Total efficiencies and costs, competitive to PV plants. are expected....

MicroCHP: Overview of selected technologies, products and field test results

Energy Technology Data Exchange (ETDEWEB)

Kuhn, Vollrad [Berliner Energieagentur GmbH, Franzoesische Strasse 23, 10117 Berlin (Germany); Klemes, Jiri; Bulatov, Igor [Centre for Process Integration, CEAS, The University of Manchester, P.O. Box 88, M60 1QD Manchester (United Kingdom)

2008-11-15

This paper gives an overview on selected microCHP technologies and products with the focus on Stirling and steam machines. Field tests in Germany, the UK and some other EC countries are presented, assessed and evaluated. Test results show the overall positive performance with differences in sectors (domestic vs. small business). Some negative experiences have been received, especially from tests with the Stirling engines and the free-piston steam machine. There are still obstacles for market implementation. Further projects and tests of microCHP are starting in various countries. When positive results will prevail and deficiencies are eliminated, a way to large-scale production and market implementation could be opened. (author)

Energy Analysis and Multi-Objective Optimization of an Internal Combustion Engine-Based CHP System for Heat Recovery

Directory of Open Access Journals (Sweden)

Abdolsaeid Ganjehkaviri

2014-10-01

Full Text Available A comprehensive thermodynamic study is conducted of a diesel based Combined Heat and Power (CHP system, based on a diesel engine and an Organic Rankine Cycle (ORC. Present research covers both energy and exergy analyses along with a multi-objective optimization. In order to determine the irreversibilities in each component of the CHP system and assess the system performance, a complete parametric study is performed to investigate the effects of major design parameters and operating conditions on the system’s performance. The main contribution of the current research study is to conduct both exergy and multi-objective optimization of a system using different working fluid for low-grade heat recovery. In order to conduct the evolutionary based optimization, two objective functions are considered in the optimization; namely the system exergy efficiency, and the total cost rate of the system, which is a combination of the cost associated with environmental impact and the purchase cost of each component. Therefore, in the optimization approach, the overall cycle exergy efficiency is maximized satisfying several constraints while the total cost rate of the system is minimized. To provide a better understanding of the system under study, the Pareto frontier is shown for multi-objective optimization and also an equation is derived to fit the optimized point. In addition, a closed form relationship between exergy efficiency and total cost rate is derived.

Hybrid Solid Oxide Fuel Cell and Thermoelectric Generator for Maximum Power Output in Micro-CHP Systems

DEFF Research Database (Denmark)

Rosendahl, Lasse; Mortensen, Paw Vestergård; Enkeshafi, Ali A.

2011-01-01

and market segments which are not yet quantified. This paper quantifies a micro-CHP system based on a solid oxide fuel cell (SOFC) and a high-performance TE generator. Based on a 3 kW fuel input, the hybrid SOFC implementation boosts electrical output from 945 W to 1085 W, with 1794 W available for heating...... the electricity production in micro-CHP systems by more than 15%, corresponding to system electrical efficiency increases of some 4 to 5 percentage points. This will make fuel cell-based micro-CHP systems very competitive and profitable and will also open opportunities in a number of other potential business...

Potential for CHP in Africa

International Nuclear Information System (INIS)

Yameogo, Gabriel

2000-01-01

It is suggested that many industries in Africa could benefit from biomass-fired cogeneration so long as the correct structures and learning processes are put in place. The article discusses Africa's energy background and gives figures for generation sources and consumption. A profile of Sudan and its energy needs is presented. It is argued that although some barriers do exist, a move to cogeneration is essential. CHP should be particularly attractive for industries able to use thermal energy for drying, heating and cooling: typical areas would be pharmaceutical and chemical plants, textile factories, cement works and steel mills

IEA Energy Technology Essentials: Biomass for Power Generation and CHP

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-01-15

The IEA Energy Technology Essentials series offers concise four-page updates on the different technologies for producing, transporting and using energy. Biomass for Power Generation and CHP is the topic covered in this edition.

Evaluation of Combined Heat and Power (CHP Systems Using Fuzzy Shannon Entropy and Fuzzy TOPSIS

Directory of Open Access Journals (Sweden)

Fausto Cavallaro

2016-06-01

Full Text Available Combined heat and power (CHP or cogeneration can play a strategic role in addressing environmental issues and climate change. CHP systems require less fuel than separate heat and power systems in order to produce the same amount of energy saving primary energy, improving the security of the supply. Because less fuel is combusted, greenhouse gas emissions and other air pollutants are reduced. If we are to consider the CHP system as “sustainable”, we must include in its assessment not only energetic performance but also environmental and economic aspects, presenting a multicriteria issue. The purpose of the paper is to apply a fuzzy multicriteria methodology to the assessment of five CHP commercial technologies. Specifically, the combination of the fuzzy Shannon’s entropy and the fuzzy Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS approach will be tested for this purpose. Shannon’s entropy concept, using interval data such as the α-cut, is a particularly suitable technique for assigning weights to criteria—it does not require a decision-making (DM to assign a weight to the criteria. To rank the proposed alternatives, a fuzzy TOPSIS method has been applied. It is based on the principle that the chosen alternative should be as close as possible to the positive ideal solution and be as far as possible from the negative ideal solution. The proposed approach provides a useful technical–scientific decision-making tool that can effectively support, in a consistent and transparent way, the assessment of various CHP technologies from a sustainable point of view.

Grid Interaction of MV-connected CHP-plants during disturbances

NARCIS (Netherlands)

Coster, E.J.; Myrzik, J.M.A.; Kling, W.L.

2009-01-01

Nowadays the amount of distributed generation (DG) units is increasing rapidly. Most dominant are combined heat and power (CHP) plants and wind turbines. At this moment, in most systems, there are no requirements defined for short-circuit behavior of such generators connected to the medium voltage

Validation of a HT-PEMFC stack for CHP applications

Energy Technology Data Exchange (ETDEWEB)

Pasupathi, S.; Ulleberg, Oe. [Western Cape Univ. (South Africa). HySA Systems, SAIAMC; Bujlo, P. [Western Cape Univ. (South Africa). HySA Systems, SAIAMC; Electrotechnical Institute Wroclaw Division (Poland); Scholta, J. [Centre for Solar Energy and Hydrogen Research (ZSW) (Germany)

2010-07-01

Fuel cell systems are very attractive for stationary co-generation applications as they can produce heat and electricity efficiently in a decentralized and environmentally friendly manner. PEMFC stacks operating at temperatures above 120 C, specifically in the range of 140-180 C, are ideal for co-generation purposes. In this study, preliminary results from a HTPEMFC stack designed for CHP applications is presented and discussed. A short, five-cell, HT-PEMFC stack was assembled with Celtec- P-2100 MEAs and validated in terms of electrical performance. The stack was operated with hydrogen and air at 160 C and the utilization curves for anode and cathode were recorded for a wide range of gas utilization at a current density of 0.52 A/cm{sup 2}. The current voltage characteristic was measured at optimal utilization values at 160 C. A 1kW stack is assembled and is currently being validated for its performance under various operating conditions for use in CHP applications. (orig.)

Micro-CHP for self-supply in the housing industry. Profitability and system integration; Mikro-BHKW zur Eigenversorgung in der Wohnungswirtschaft. Wirtschaftlichkeit und Systemintegration

Energy Technology Data Exchange (ETDEWEB)

Hollinger, Raphael; Buettner, Markus; Erge, Thomas; Wille-Haussmann, Bernhard; Wittwer, Christof [Fraunhofer-Institut fuer Solare Energiesysteme ISE, Freiburg (Germany)

2011-07-01

The use of micro-CHP units in multifamily buildings is particularly profitable if the produced electricity - coupled with the thermal energy production - is used directly by the operator or sold locally. To maximize the share of own consumption the use of thermal storages to operate the CHP at times of high electrical demand is necessary. By conducting a field test it is shown that the share of own consumption can be increased by predictive control of CHP with thermal storages. The approach increases the profitability of the CHP operation under today's conditions as well as the system integration of the CHP electricity. (orig.)

Energetic and environmental performance of three biomass upgrading processes integrated with a CHP plant

International Nuclear Information System (INIS)

Kohl, Thomas; Laukkanen, Timo; Järvinen, Mika; Fogelholm, Carl-Johan

2013-01-01

Highlights: ► We simulate CHP-integrated production of wood pellets, torrefied wood pellets and pyrolysis slurry. ► Integration increases operation hours and district heat output by up to 38% and 22%. ► Additionally installed equipment reduces yearly power generation by up to 7%. ► Wood pellet production performs best energetically and environmentally. ► Integrated concepts substantially reduce fuel consumption and CO 2 emissions. - Abstract: In order to react on future expected increased competition on restricted biomass resources, communal combined heat and power (CHP) plants can be integrated with biomass upgrading processes that add valuable products to the portfolio. In this paper, outgoing from a base case, the retrofit integration of production of wood pellets (WPs), torrefied wood pellets (TWPs) and wood fast pyrolysis slurry (PS) with an existing wood-fired CHP plant was simulated. Within the integration concept, free boiler capacity during times of low district heat demands is used to provide energy for the upgrading processes. By detailed part-load modelling, critical process parameters are discussed. With help of a multiperiod model of the heat duration curve, the work further shows the influence of the integration on plant operating hours, electricity production and biomass throughput. Environmental and energetic performance is assessed according to European standard EN 15603 and compared to the base case as well as to stand-alone production in two separate units. The work shows that all three integration options are well possible within the operational limits of the CHP plant. Summarising, this work shows that integration of WP, TWP and PS production from biomass with a CHP plant by increasing the yearly boiler workload leads to improved primary energy efficiency, reduced CO 2 emissions, and, when compared to stand-alone production, also to substantial fuel savings

Anti-diabetic effect of Cyclo-His-Pro (CHP)-enriched yeast ...

African Journals Online (AJOL)

Anti-diabetic effect of Cyclo-His-Pro (CHP)-enriched yeast hydrolysate in ... The present study was designed to investigate the hypoglycemic effects of the daily ... in the area under curve (AUC) value of YH supplemented groups as compared ...

CHP Integrated with Burners for Packaged Boilers

Energy Technology Data Exchange (ETDEWEB)

Castaldini, Carlo; Darby, Eric

2013-09-30

The objective of this project was to engineer, design, fabricate, and field demonstrate a Boiler Burner Energy System Technology (BBEST) that integrates a low-cost, clean burning, gas-fired simple-cycle (unrecuperated) 100 kWe (net) microturbine (SCMT) with a new ultra low-NOx gas-fired burner (ULNB) into one compact Combined Heat and Power (CHP) product that can be retrofit on new and existing industrial and commercial boilers in place of conventional burners. The Scope of Work for this project was segmented into two principal phases: (Phase I) Hardware development, assembly and pre-test and (Phase II) Field installation and demonstration testing. Phase I was divided into five technical tasks (Task 2 to 6). These tasks covered the engineering, design, fabrication, testing and optimization of each key component of the CHP system principally, ULNB, SCMT, assembly BBEST CHP package, and integrated controls. Phase I work culminated with the laboratory testing of the completed BBEST assembly prior to shipment for field installation and demonstration. Phase II consisted of two remaining technical tasks (Task 7 and 8), which focused on the installation, startup, and field verification tests at a pre-selected industrial plant to document performance and attainment of all project objectives. Technical direction and administration was under the management of CMCE, Inc. Altex Technologies Corporation lead the design, assembly and testing of the system. Field demonstration was supported by Leva Energy, the commercialization firm founded by executives at CMCE and Altex. Leva Energy has applied for patent protection on the BBEST process under the trade name of Power Burner and holds the license for the burner currently used in the product. The commercial term Power Burner is used throughout this report to refer to the BBEST technology proposed for this project. The project was co-funded by the California Energy Commission and the Southern California Gas Company (SCG), a

IVO`s CHP know-how: experience, inventions, patents

Energy Technology Data Exchange (ETDEWEB)

Aeijaelae, M.; Ohtonen, V. [ed.

1997-11-01

IVO can justly claim mastery in the co-generation of district heat and electricity - CHP. As well as looking at the issue from the viewpoint of planners, builders and operators, IVO`s engineers also view power plants through the eyes of the product developer and inventor. This approach has resulted in successful power plant configurations, inventions and patents and visions

Performance and cost results from a DOE Micro-CHP demonstration facility at Mississippi State University

International Nuclear Information System (INIS)

Giffin, Paxton K.

2013-01-01

Highlights: ► We examine the cost and performance results of a Micro-CHP demonstration facility. ► Evaluation includes both summer and winter performance. ► Evaluation in comparison to a conventional HVAC system using grid power. ► Influence of improperly sized equipment. ► Influence of natural gas prices on the viability of CHP projects using that fuel. - Abstract: Cooling, Heating, and Power (CHP) systems have been around for decades, but systems that utilize 20 kW or less, designated as Micro-CHP, are relatively new. A demonstration site has been constructed at Mississippi State University (MSU) to show the advantages of these micro scale systems. This study is designed to evaluate the performance of a Micro-CHP system as opposed to a conventional high-efficiency Heating, Ventilation, and Air Conditioning (HVAC) system that utilizes electrical power from the existing power grid. Raw data was collected for 7 months to present the following results. The combined cycle efficiency from the demonstration site was averaged at 29%. The average combined boiler and engine cost was $1.8 h −1 of operation for heating season and $3.9 h −1 of operation for cooling season. The cooling technology used, an absorption chiller exhibited an average Coefficient of Performance (COP) of 0.27. The conventional high-efficiency system, during cooling season, had a COP of 4.7 with a combined cooling and building cost of $0.2 h −1 of operation. During heating mode, the conventional system had an efficiency of 47% with a fuel and building electrical cost of $0.28 h −1 of operation.

Crystallization and preliminary crystallographic analysis of the human calcineurin homologous protein CHP2 bound to the cytoplasmic region of the Na+/H+ exchanger NHE1

International Nuclear Information System (INIS)

Ben Ammar, Youssef; Takeda, Soichi; Sugawara, Mitsuaki; Miyano, Masashi; Mori, Hidezo; Wakabayashi, Shigeo

2005-01-01

Crystallization of the human CHP2–NHE1 binding domain complex. Calcineurin homologous protein (CHP) is a Ca 2+ -binding protein that directly interacts with and regulates the activity of all plasma-membrane Na + /H + -exchanger (NHE) family members. In contrast to the ubiquitous isoform CHP1, CHP2 is highly expressed in cancer cells. To understand the regulatory mechanism of NHE1 by CHP2, the complex CHP2–NHE1 (amino acids 503–545) has been crystallized by the sitting-drop vapour-diffusion method using PEG 3350 as precipitant. The crystals diffract to 2.7 Å and belong to a tetragonal space group, with unit-cell parameters a = b = 49.96, c = 103.20 Å

Characterization of ultrafine and fine particles from CHP Plants

Energy Technology Data Exchange (ETDEWEB)

2009-08-15

Samples of particles collected at CHP plants in the project 'Survey of emissions from CHP Plants' have been analysed in this project to give information on the morphology and chemical composition of individual particle size classes. The objective of this project was to characterize ultrafine and fine particles emitted to the atmosphere from Danish CHP plants. Nine CHP plants were selected in the Emission Survey Project as being representative for the different types of CHP plants operating in Denmark: 1) Three Waste-to Energy (WTE) plants. 2) Three biomass fired (BM) plants (two straw fired, one wood/saw dust fired). 3) Two gas fired (GF) plants (one natural gas, one landfill gas fired). 4) One gasoil (GO) fired plant. At the WTE and BM plants, various types of emission control systems implemented. The results from these plants represent the composition and size distribution of combustion particles that are emitted from the plants emission control systems. The measured emissions of particles from the waste-to-energy plants WTE1-3 are generally very low. The number and mass concentrations of ultrafine particles (PM{sub 0.1}) were particularly low in the flue gas from WTE2 and WTE3, where bag filters are used for the reduction of particle emissions. The EDX analysis of particles from the WTE plants indicates that the PM{sub 0.1} that penetrates the ECS at WTE can contain high fractions of metals such as Fe, Mn and Cu. The SEM analysis of particles from WTE1-3 showed that the particles were generally porous and irregular in shape. The concentrations of particles in the flue gas from the biomass plants were generally higher than found for the WTE plants. The time series results showed that periodical, high concentration peaks of PM emissions occur from BM1 and BM2. The chemical composition of the particles emitted from the three biomass plants is generally dominated by C, O and S, and to some extend also Fe and Si. A high amount of Cu was found in selected

EPA's Air Quality Rules for Reciprocating Internal Combustion Engines (RICE) and their Application to CHP (Webinar) – June 24, 2014

Science.gov (United States)

This webinar discusses the effect of EPA's air quality regulations on CHP facilities and stationary RICE, and describes how CHP systems can comply with air quality regulations by using stationary RICE.

New CHP plant for a rubber products manufacturer; Nueva planta e cogeneración para un fabricante de productos de hule

Energy Technology Data Exchange (ETDEWEB)

Vila, R.; Martí, C.

2016-07-01

At the end of 2014 the company Industrias de Hule Galgo decided to undertake the installation project of an efficient CHP plant for its production plant, with the aim of bringing down energy costs and improving the company’s competitive position in the market. The new plant has already started its first operational phase. The project has comprised the installation of a single cycle with gas-powered gensets providing a total electrical capacity of 6.6 MW. This provides the necessary thermal oil for the production plant; covers 100% of the electrical power consumed by the industrial complex; and also generates cooling water, giving improved production capacity by supercooling the extrusion system. To execute these works, Industrias de Hule Galgo contracted the services of engineering company AESA to provide the engineering, procurement and construction of the CHP plant. (Author)

Distributed Control in a Network of Households with microCHP

NARCIS (Netherlands)

Larsen, Gunn; Scherpen, Jacquelien M.A.; van Foreest, Nicolaas

2011-01-01

This is an application of a dynamic price mechanism to distributed optimization of a network of houses which are both producers and consumers of electricity. One possibility for domestic generation is the Micro Combined Heat Power system (µCHP). We use a pricing mechanism based on dual

Economic analysis of a supercritical coal-fired CHP plant integrated with an absorption carbon capture installation

International Nuclear Information System (INIS)

Bartela, Łukasz; Skorek-Osikowska, Anna; Kotowicz, Janusz

2014-01-01

Energy investments in Poland are currently focused on supercritical coal-fired unit technology. It is likely, that in the future, these units are to be integrated with carbon capture and storage (CCS) installations, which enable a significant reduction of greenhouse gas emissions into the atmosphere. A significant share of the energy market in Poland is constituted by coal-fired combined heat and power (CHP) plants. The integration of these units with CCS installation can be economically inefficient. However, the lack of such integration enhances the investment risk due to the possibility of appearing on the market in the near future high prices of emission allowances. The aforementioned factors and additional favorable conditions for the development of cogeneration can cause one to consider investing in large supercritical CHP plants. This paper presents the results of an economic analysis aimed at comparing three cases of CHP plants, one without an integrated CCS installation and two with such installations. The same steam cycle structure for all variants was adopted. The cases of integrated CHP plants differ from each other in the manner in which they recover heat. For the evaluation of the respective solutions, the break-even price of electricity and avoided emission cost were used. - Highlights: • The simulations of operation of CHP plants under changing load have been realized. • For analyzed cases sensitivity analyses of economic indices have been conducted. • Conditions of competitiveness for integration with CCS units have been identified. • Integration can be profitable if prices of allowance will reach high values, exceeding 50 €/MgCO 2 . • Others important factors are the investment costs and operation and maintenance costs

Modeling of non-linear CHP efficiency curves in distributed energy systems

DEFF Research Database (Denmark)

Milan, Christian; Stadler, Michael; Cardoso, Gonçalo

2015-01-01

Distributed energy resources gain an increased importance in commercial and industrial building design. Combined heat and power (CHP) units are considered as one of the key technologies for cost and emission reduction in buildings. In order to make optimal decisions on investment and operation...... for these technologies, detailed system models are needed. These models are often formulated as linear programming problems to keep computational costs and complexity in a reasonable range. However, CHP systems involve variations of the efficiency for large nameplate capacity ranges and in case of part load operation......, which can be even of non-linear nature. Since considering these characteristics would turn the models into non-linear problems, in most cases only constant efficiencies are assumed. This paper proposes possible solutions to address this issue. For a mixed integer linear programming problem two...

Crystallization and preliminary crystallographic analysis of the human calcineurin homologous protein CHP2 bound to the cytoplasmic region of the Na{sup +}/H{sup +} exchanger NHE1

Energy Technology Data Exchange (ETDEWEB)

Ben Ammar, Youssef [Department of Molecular Physiology, National Cardiovascular Center Research Institute, Fujishiro-dai 5-7-1, Suita, Osaka 565-8565 (Japan); Takeda, Soichi [Department of Cardiac Physiology, National Cardiovascular Center Research Institute, Fujishiro-dai 5-7-1, Suita, Osaka 565-8565 (Japan); Sugawara, Mitsuaki; Miyano, Masashi [Structural Biophysics Laboratory, RIKEN Harima Institute at SPring-8, Kouto, Mikazuki, Sayo, Hyogo 679-5148 (Japan); Mori, Hidezo [Department of Cardiac Physiology, National Cardiovascular Center Research Institute, Fujishiro-dai 5-7-1, Suita, Osaka 565-8565 (Japan); Wakabayashi, Shigeo, E-mail: wak@ri.ncvc.go.jp [Department of Molecular Physiology, National Cardiovascular Center Research Institute, Fujishiro-dai 5-7-1, Suita, Osaka 565-8565 (Japan)

2005-10-01

Crystallization of the human CHP2–NHE1 binding domain complex. Calcineurin homologous protein (CHP) is a Ca{sup 2+}-binding protein that directly interacts with and regulates the activity of all plasma-membrane Na{sup +}/H{sup +}-exchanger (NHE) family members. In contrast to the ubiquitous isoform CHP1, CHP2 is highly expressed in cancer cells. To understand the regulatory mechanism of NHE1 by CHP2, the complex CHP2–NHE1 (amino acids 503–545) has been crystallized by the sitting-drop vapour-diffusion method using PEG 3350 as precipitant. The crystals diffract to 2.7 Å and belong to a tetragonal space group, with unit-cell parameters a = b = 49.96, c = 103.20 Å.

Financing CHP Projects at Wastewater Treatment Facilities with Clean Water State Revolving Funds

Science.gov (United States)

This factsheet provides information about CHP at wastewater treatment facilities, including applications, financial challenges, and financial opportunities, such as the Clean Water State Revolving Fund.

Analysis of the impact of Heat-to-Power Ratio for a SOFC-based mCHP system for residential application under different climate regions in Europe

DEFF Research Database (Denmark)

Liso, Vincenzo; Zhao, Yingru; Brandon, Nigel

2011-01-01

In this paper, the ability of a micro combined heat and power (mCHP) system to cover the heat and electricity demand of a single-family residence is investigated. A solid oxide fuel cell based mCHP system coupled with a hot water storage tank is analyzed. The energy profiles of single-family hous......In this paper, the ability of a micro combined heat and power (mCHP) system to cover the heat and electricity demand of a single-family residence is investigated. A solid oxide fuel cell based mCHP system coupled with a hot water storage tank is analyzed. The energy profiles of single...... according to the summer energy demand. The winter energy demand shows a Heat-to-Power Ratio which cannot be covered by the mCHP unit alone. To ensure that the mCHP system meets both the thermal and electrical energy demand over the entire year, an auxiliary boiler and a hot water storage tank need...

Investment in new power generation under uncertainty: Benefits of CHP vs. condensing plants in a copula-based analysis

International Nuclear Information System (INIS)

Westner, Günther; Madlener, Reinhard

2012-01-01

In this paper, we apply a spread-based real options approach to analyze the decision-making problem of an investor who has the choice between an irreversible investment in a condensing power plant without heat utilization and a plant with combined heat-and-power (CHP) generation. Our investigation focuses on large-scale fossil-fueled generation technologies and is based on a stochastic model that uses copula functions to provide the input parameters of the real options model. We define the aggregated annual spread as assessment criteria for our investigation since it contains all relevant volatile input parameters that have an impact on the evaluation of investment decisions. We show that the specific characteristics of CHP plants, such as additional revenues from heat sales, promotion schemes, specific operational features, and a beneficial allocation of CO 2 allowances, have a significant impact on the option value and therefore on the optimal timing for investment. For the two fossil-fueled CHP technologies investigated (combined-cycle gas turbine and steam turbine), we conclude from our analysis that a high share of CHP generation reduces the risk exposure for the investor. The maximal possible CHP generation depends significantly on the local heat demand in the surroundings of the power plant. Considering this, the size of the heat sink available could gain more relevance in the future selection process of sites for new large-scale fossil power plants.

Flue gas condensation in straw fired CHP plants; Roeggaskondensation i halmfyrede kraftvarmeanlaeg

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-06-15

The high price of straw and a general demand for increased use of straw in power and heat production are expected to result in an increased need for efficient fuel utilization. The use of flue gas condensation in straw fired CHP plants can contribute to a higher exploitation of energy, and at the same time open of the possibility of utilization of wet (cheaper) fuels without energy loss. Furthermore flue gas condensation can contribute to the flue gas cleaning process through removal of HCl and SO{sub 2} as well as in particle cleaning in wet cleaning processes. With starting point in a straw fired CHP plant the technical and economic consequences of installation of a flue gas condensation system are investigated. Fuel exploitation and power/heat production distribution is included in the investigation. (BA)

A Stochastic Unit Commitment Model for a Local CHP Plant

DEFF Research Database (Denmark)

Ravn, Hans V.; Riisom, Jannik; Schaumburg-Müller, Camilla

2005-01-01

Local CHP development in Denmark has during the 90’s been characterised by large growth primarily due to government subsidies in the form of feed-in tariffs. In line with the liberalisation process in the EU, Danish local CHPs of a certain size must operate on market terms from 2005. This paper...

Development of a CHP/DH system for the new town of Parand: An opportunity to mitigate global warming in Middle East

International Nuclear Information System (INIS)

Mostafavi Tehrani, S. Saeed; Saffar-Avval, M.; Mansoori, Z.; Behboodi Kalhori, S.; Abbassi, A.; Dabir, B.; Sharif, M.

2013-01-01

As a result of the worldwide concern about global warming, projects that target reduction of greenhouse gas emissions have gained a lot of interest. The idea of this paper is to recover exhaust hot gases of an existing gas turbine power plant to meet dynamic thermal energy requirements of a residential area (the new town of Parand) situated in the suburb of Tehran, and also use the rest of the heat source potential to feed a steam turbine cycle. In close proximity to this town, there are two GT plants: Parand (954 MW e ) and Rudeshur (790 MW e ). For handling the CHP/STC/DH plant, two methods are considered along with thermal load following operation strategy: maximum power generation (MPG) and minimum fuel consumption (MFC). Then, the alternatives are compared in terms of annual PES, CO 2 abatement and NPV. For the best design from environmental viewpoint (Parand CHP-B), PES, CO 2 abatement and NPV are calculated to be 27.31%, 2.56 million tons and 1491 million dollar, respectively. -- Highlights: • To propose a technical and financial methodology to evaluate CHP/DH projects. • To address environmental advantages of CHPs with conventional plants. • To present practical operation strategies to increase benefits of CHP/DH plants. • To report/compare benefits of various CHP/DH alternatives for a case study in Iran. • To conduct a comprehensive energy analysis of proposed CHP/DH design options

TaCHP: a wheat zinc finger protein gene down-regulated by abscisic acid and salinity stress plays a positive role in stress tolerance.

Science.gov (United States)

Li, Cuiling; Lv, Jian; Zhao, Xin; Ai, Xinghui; Zhu, Xinlei; Wang, Mengcheng; Zhao, Shuangyi; Xia, Guangmin

2010-09-01

The plant response to abiotic stresses involves both abscisic acid (ABA)-dependent and ABA-independent signaling pathways. Here we describe TaCHP, a CHP-rich (for cysteine, histidine, and proline rich) zinc finger protein family gene extracted from bread wheat (Triticum aestivum), is differentially expressed during abiotic stress between the salinity-sensitive cultivar Jinan 177 and its tolerant somatic hybrid introgression cultivar Shanrong No.3. TaCHP expressed in the roots of seedlings at the three-leaf stage, and the transcript localized within the cells of the root tip cortex and meristem. TaCHP transcript abundance was higher in Shanrong No.3 than in Jinan 177, but was reduced by the imposition of salinity or drought stress, as well as by the exogenous supply of ABA. When JN17, a salinity hypersensitive wheat cultivar, was engineered to overexpress TaCHP, its performance in the face of salinity stress was improved, and the ectopic expression of TaCHP in Arabidopsis (Arabidopsis thaliana) also improved the ability of salt tolerance. The expression level of a number of stress reporter genes (AtCBF3, AtDREB2A, AtABI2, and AtABI1) was raised in the transgenic lines in the presence of salinity stress, while that of AtMYB15, AtABA2, and AtAAO3 was reduced in its absence. The presence in the upstream region of the TaCHP open reading frame of the cis-elements ABRE, MYBRS, and MYCRS suggests that it is a component of the ABA-dependent and -independent signaling pathways involved in the plant response to abiotic stress. We suggest that TaCHP enhances stress tolerance via the promotion of CBF3 and DREB2A expression.

Optimization of operation for combined heat and power plants - CHP plants - with heat accumulators using a MILP formulation

Energy Technology Data Exchange (ETDEWEB)

Grue, Jeppe; Bach, Inger [Aalborg Univ. (Denmark). Inst. of Energy Technology]. E-mails: jeg@iet.auc.dk; ib@iet.auc.dk

2000-07-01

The power generation system in Denmark is extensively based on small combined heat and power plants (CHP plants), producing both electricity and district heating. This project deals with smaller plants spread throughout the country. Often a heat accumulator is used to enable electricity production, even when the heat demand is low. This system forms a very complex problem, both for sizing, designing and operation of CHP plants. The objective of the work is the development of a tool for optimisation of the operation of CHP plants, and to even considering the design of the plant. The problem is formulated as a MILP-problem. An actual case is being tested, involving CHP producing units to cover the demand. The results from this project show that it is of major importance to consider the operation of the plant in detail already in the design phase. It is of major importance to consider the optimisation of the plant operation, even at the design stage, as it may cause the contribution margin to rise significantly, if the plant is designed on the basis of a de-tailed knowledge of the expected operation. (author)

Emissions from decentralised CHP plants 2007 - Energinet.dk Environmental project no. 07/1882. Project report 5 - Emission factors and emission inventory for decentralised CHP production

Energy Technology Data Exchange (ETDEWEB)

Nielsen, Malene; Nielsen, Ole-Kenneth; Thomsen, M.

2010-06-15

Updated emission factors for decentralised combined heat and power (CHP) plants with a capacity < 25MWe have been estimated based on project emission measurements as well as emission measurements performed in recent years that were collected. The emission factors valid for 2006/2007 have been estimated for the plant technologies: Municipal solid waste (MSW) incineration plants, plants combusting straw or wood, natural gas fuelled reciprocating engines, biogas fuelled engines, natural gas fuelled gas turbines, gas oil fuelled reciprocating engines, gas oil fuelled gas turbines, steam turbines combusting residual oil and reciprocating engines combusting biomass producer gas based on wood. The emission factors for MSW incineration plants are much lower than the emission factors that were estimated for year 2000. The considerable reduction in the emission factors is a result of lower emission limit values in Danish legislation since 2006 that has lead to installation of new and improved flue gas cleaning systems in most MSW incineration plants. For CHP plants combusting wood or straw no major technical improvements have been implemented. The emission factors for natural gas fuelled reciprocating engines have been reduced since year 2000 as a result of technical improvements that have been carried out due to lower emission limit values in Danish legislation. The NO{sub x} emission factor for natural gas fuelled gas turbines has decreased 62 % since year 2000. This is a result of installation of low-NO{sub x} burners in almost all gas turbines that has been necessary to meet new emission limits in Danish legislation. The emission measurements programme included screening of the emissions of HCB, PCB, PCDD/-F and PBDD/-F. Compared to the Danish national emission decentralized CHP plants are major emission sources for CH{sub 4}, NO{sub x}, SO{sub 2}, heavy metals and HCB. (author)

Economic feasibility of CHP facilities fueled by biomass from unused agriculture land

DEFF Research Database (Denmark)

Pfeifer, Antun; Dominkovic, Dominik Franjo; Ćosić, Boris

2016-01-01

In this paper, the energy potential of biomass from growing short rotation coppice on unused agricultural land in the Republic of Croatia is used to investigate the feasibility of Combined Heat and Power (CHP) facilities fueled by such biomass. Large areas of agricultural land that remain unused...... work and is now used to investigate the conditions in which such energy facilities could be feasible. The overall potential of biomass from short rotation coppice cultivated on unused agricultural land in the scenarios with 30% of the area is up to 10PJ/year. The added value of fruit trees pruning...... biomass represents an incentive for the development of fruit production on such agricultural land. Sensitivity analysis was conducted for several parameters: cost of biomass, investment costs in CHP systems and combined change in biomass and technology cost....

Optimal design of integrated CHP systems for housing complexes

International Nuclear Information System (INIS)

Fuentes-Cortés, Luis Fabián; Ponce-Ortega, José María; Nápoles-Rivera, Fabricio; Serna-González, Medardo; El-Halwagi, Mahmoud M.

2015-01-01

Highlights: • An optimization formulation for designing domestic CHP systems is presented. • The operating scheme, prime mover and thermal storage system are optimized. • Weather conditions and behavior demands are considered. • Simultaneously economic and environmental objectives are considered. • Two case studies from Mexico are presented. - Abstract: This paper presents a multi-objective optimization approach for designing residential cogeneration systems based on a new superstructure that allows satisfying the demands of hot water and electricity at the minimum cost and the minimum environmental impact. The optimization involves the selection of technologies, size of required units and operating modes of equipment. Two residential complexes in different cities of the State of Michoacán in Mexico were considered as case studies. One is located on the west coast and the other one is in the mountainous area. The results show that the implementation of the proposed optimization method yields significant economic and environmental benefits due to the simultaneous reduction in the total annual cost and overall greenhouse gas emissions

Putney Basketville Site Biomass CHP Analysis

Energy Technology Data Exchange (ETDEWEB)

Hunsberger, Randolph [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mosey, Gail [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2013-10-01

The U.S. Environmental Protection Agency (EPA) Office of Solid Waste and Emergency Response Center for Program Analysis developed the RE-Powering America's Land initiative to reuse contaminated sites for renewable energy generation when aligned with the community's vision for the site. The Putney, Vermont, Basketville site, formerly the location of a basket-making facility and a paper mill andwoolen mill, was selected for a feasibility study under the program. Biomass was chosen as the renewable energy resource based on abundant woody-biomass resources available in the area. Biomass combined heat and power (CHP) was selected as the technology due to nearby loads, including Putney Paper and Landmark College.

Operational Strategies for a Portfolio of Wind Farms and CHP Plants in a Two-Price Balancing Market

DEFF Research Database (Denmark)

Hellmers, Anna; Zugno, Marco; Skajaa, Anders

2015-01-01

In this paper we explore the portfolio effect of a system consisting of a Combined Heat and Power (CHP) plant and a wind farm. The goal is to increase the overall profit of the portfolio by reducing imbalances, and consequently their implicit penalty in a two-price balancing market for electricity......-horizon fashion, so that forecasts for heat demand, wind power production and market prices are updated at each iteration. We conclude that the portfolio strategy is the most profitable due to the two-price structure of the balancing market. This encourages producers to handle their imbalances outside the market........ We investigate two different operational strategies, which differ in whether the CHP plant and the wind farm are operated jointly or independently, and we evaluate their economic performance on a real case study based on a CHP-wind system located in the western part of Denmark. We present...

Calorimetric studies and lessons on fires and explosions of a chemical plant producing CHP and DCPO

International Nuclear Information System (INIS)

Hsu, Jing-Ming; Su, Mao-Sheng; Huang, Chiao-Ying; Duh, Yih-Shing

2012-01-01

Highlights: ► We analyzed fire and explosion incidents in a plant producing CHP and DCPO. ► Data from calorimeters reveal causes and phenomena associated with the incidents. ► The credible worst scenario was thermal explosion. ► Incidents may be avoided by implementing DIERS methodology. - Abstract: Cumene hydroperoxide (CHP) has been used in producing phenol, dicumyl peroxide (DCPO) and as an initiator for synthesizing acrylonitrile–butadiene–styrene (ABS) resin by copolymerization in Taiwan. Four incidents of fire and explosion induced by thermal runaway reactions were occurred in a same plant producing CHP, DCPO and bis-(tert-butylperoxy isopropyl) benzene peroxide (BIBP). The fourth fire and explosion occurred in the CHP reactor that resulted in a catastrophic damage in reaction region and even spread throughout storage area. Descriptions on the occurrences of these incidents were assessed by the features of processes, reaction schemes and unexpected side reactions. Calorimetric data on thermokinetics and pressure were used for explaining the practical consequences or which the worst cases encountered in this kind of plant. Acceptable risk associated with emergency relief system design is vital for a plant producing organic peroxide. These basic data for designing an inherently safer plant can be conducted from adiabatic calorimetry. An encouraging deduction has been drawn here, these incidents may be avoided by the implementation of API RP 520, API RP 521, DIERS technology, OSHA 1910.119 and AIChE's CCPS recommended PSM elements.

Optimal Design and Operation of A Syngas-fuelled SOFC Micro-CHP System for Residential Applications in Different Climate Zones in China

DEFF Research Database (Denmark)

Yang, Wenyuan; Liso, Vincenzo; Zhao, Yingru

2013-01-01

heat-to-power load ratio. Therefore, the aim of this study is to investigate the optimal design and operation of a syngas-fuelled SOFC micro-CHP system for small households located in five different climate zones in China. The ability of the micro-CHP to cover the heat and electricity demand of a 70m2...... demand. Numerical simulations are conducted in Matlab environment. System design trade-offs are discussed to determine the optimal match between the energy demand of the household for different climates across China and the energy supply of the micro-CHP during the whole year. Moreover, criteria...

Future market relevance of CHP installations with electrical ratings from 1 to 1000 kW; Zukuenftige Marktbedeutung von WKK-Anlagen mit 1 - 1000 kW elektrischer Leistung

Energy Technology Data Exchange (ETDEWEB)

Eicher, H.; Rigassi, R.

2003-12-15

This report for the Swiss Federal Office of Energy (SFOE) discusses the future market relevance of combined heat and power (CHP) installations with electrical ratings from 1 to 1000 kW. Developments over the past ten years are reviewed. Important reductions in the price of motor-driven CHP units and the price of the electrical power produced are noted and commented on. The technical market potential of CHP units and the degree to which this potential has been implemented are commented on. Work done, including CHP implementation in the industrial, commercial and residential areas, is commented on. Future developments both in the technical area as well as in commercial areas are commented on. Micro-gas-turbine based CHP systems are also discussed, as are fuel-cell based systems in both the higher and lower capacity power generation area. The prospects for CHP systems in general in the electricity generation area are discussed

Innovative Hybrid CHP systems for high temperature heating plant in existing buildings

NARCIS (Netherlands)

de Santoli, Livio; Lo Basso, Gianluigi; Nastasi, B.; d’Ambrosio Alfano, Francesca R.; Mazzarella and Piercarlo, Livio

2017-01-01

This paper deals with the potential role of new hybrid CHP systems application providing both electricity and heat which are compatible with the building architectural and landscape limitations. In detail, three different plant layout options for high temperature heat production along with the

The Significance of a Building’s Energy Consumption Profiles for the Optimum Sizing of a Combined Heat and Power (CHP System—A Case Study for a Student Residence Hall

Directory of Open Access Journals (Sweden)

Khuram Pervez Amber

2018-06-01

Full Text Available University buildings, such as student residence halls with year-round consistent energy demands, offer strong opportunities for Combined Heat and Power (CHP systems. The economic and environmental feasibility of a CHP project is strongly linked with its optimum sizing. This study aims to undertake such an assessment for a CHP system for a student residence hall located in London, the United Kingdom (UK. The study also aims to undertake a sensitivity analysis to investigate the effect of different parameters on the project’s economics. Necessary data are collected via interviews with the University’s Energy Manager. Modeling of the CHP system is performed using the London South Bank University (LSBU, London, the UK CHP model. Results demonstrate that optimum sizing of CHP is crucial for achieving higher economic and environmental benefits and strongly depends on the authenticity of the energy consumption data, based on which the CHP is being sized. Use of incorrect energy data could result in an undersized or oversized CHP system, where an oversized system will result in higher negative results compared to an undersized system. Finally, Monto Carlo statistical analysis shows that electricity price is the significant factor that could affect the project’s economics. With an increasing spark gap, the payback period decreases, and vice versa.

SOFC/TEG hybrid mCHP system. Final report

Energy Technology Data Exchange (ETDEWEB)

2012-03-15

The starting point for this project have been the challenge has been to develop a cost effective solution with long term stability. This is where a focused effort in a strong consortium covering material research, module development and manufacture as well as device design and optimization can make a real difference. In March 2010 the SOFTEG phase II project was initiated and a cooperation organization was established to implement the project as a development and demonstration project involving the staff from all project partners. The project is now completed with excellent and documented outcome. The final results by Alpcon have been demonstration as a TEG-based mCHP system calls CHP Dual Engine Power System, which will be applicable as both a standalone TEG-CHP hybrid system, but also as an auxiliary power unit and power booster for the SOFC system. However the SOFC system cannot cover the household's heat demand alone so it is necessary to combine a SOFC system together with a water heater/boiler system to cover the peak heat demand of a residential house or a complex building. The SOFTEG project partners achieved significant results that mainly can be outlined as following: 1) University of Aarhus has improved the thermal stability of ZnSb by optimizing the concentration of Nano composite material. 2) The grain size and its influence on the sintering process by spark plasma method are investigated by Aarhus University, but further work seems to be necessary. 3) The TE material is going to commercialization by Aarhus University. 4) Aalborg University has prepared simulation tools for complex thermoelectric simulation in non-steady state condition. 5) The new type DCDC interleaved converter using the MPPT system for optimal power tracing is designed, build and tested by Aalborg University in cooperation with Alpcon. This task is included overall system design, control system implementation and power electronic control design. 6) Full scale practical

Optimal design and operation of a syngas-fuelled SOFC micro CHP system for residential applications in different climate zones in China

DEFF Research Database (Denmark)

Yang, Wenyuan; Zhao, Yingru; Liso, Vincenzo

2014-01-01

under difference climate conditions to ensure that it is well matched with the local heat-to-power ratio. The aim of this study is to investigate the optimal design and operation of a syngas-fuelled SOFC micro-CHP system for small households located in five different climate zones in China. The ability...... of the micro-CHP to cover the heat and electricity demand of a 70 m2 single-family apartment with an average number of occupants of 3 is evaluated. A detailed model of the micro-CHP unit coupled with a hot water storage tank and an auxiliary boiler is developed. System design trade-offs are discussed...

Preliminary experimental investigation of a natural gas-fired ORC-based micro-CHP system for residential buildings

International Nuclear Information System (INIS)

Farrokhi, M.; Noie, S.H.; Akbarzadeh, A.A.

2014-01-01

The continual increases in energy demand and greenhouse gas emissions, call for efficient use of energy resources. Decentralized combined heat and power (CHP) technology provides an alternative for the world to meet and solve energy-related problems including energy shortages, energy supply security, emission control and conservation of energy. This paper presents the preliminary results of an experimental investigation of a natural gas-fired micro-CHP system for residential buildings based on an organic Rankine cycle (ORC). Isopentane was used as the ORC working fluid in consideration of several criteria including its environmentally-friendly characteristics. Experiments were conducted to evaluate the performance of the developed system at different heat source temperatures of nominally 85, 80, 75, 70, and 65 °C. The maximum electrical power output of 77.4 W was generated at heating water entry temperature of 84.1 °C, corresponding to net cycle electrical efficiency of 1.66%. Further work will be done with a view to increasing the cycle electrical efficiency by using more efficient components, in particular the expander and generator. - Highlights: •A natural gas-fired ORC-based micro-scale CHP system has been developed and tested. •The good agreement between the mechanical and gross power validates the assumptions. •A vane expander suits a micro-CHP system based on an organic Rankine cycle. •A vane expander does not suit power generation by a Trilateral Flash Cycle (TFC). •Domestic gas-fired ORC systems may reduce reliance on central power stations

Calorimetric studies and lessons on fires and explosions of a chemical plant producing CHP and DCPO

Energy Technology Data Exchange (ETDEWEB)

Hsu, Jing-Ming; Su, Mao-Sheng; Huang, Chiao-Ying [Department of Occupational Safety and Health, Chia Nan University of Pharmacy and Science, Tainan, Taiwan, ROC (China); Duh, Yih-Shing, E-mail: yihshingduh@yahoo.com.tw [Department of Safety, Health and Environmental Engineering, National United University, No. 1 Lien-Da, Miaoli, Taiwan, ROC (China)

2012-05-30

Highlights: Black-Right-Pointing-Pointer We analyzed fire and explosion incidents in a plant producing CHP and DCPO. Black-Right-Pointing-Pointer Data from calorimeters reveal causes and phenomena associated with the incidents. Black-Right-Pointing-Pointer The credible worst scenario was thermal explosion. Black-Right-Pointing-Pointer Incidents may be avoided by implementing DIERS methodology. - Abstract: Cumene hydroperoxide (CHP) has been used in producing phenol, dicumyl peroxide (DCPO) and as an initiator for synthesizing acrylonitrile-butadiene-styrene (ABS) resin by copolymerization in Taiwan. Four incidents of fire and explosion induced by thermal runaway reactions were occurred in a same plant producing CHP, DCPO and bis-(tert-butylperoxy isopropyl) benzene peroxide (BIBP). The fourth fire and explosion occurred in the CHP reactor that resulted in a catastrophic damage in reaction region and even spread throughout storage area. Descriptions on the occurrences of these incidents were assessed by the features of processes, reaction schemes and unexpected side reactions. Calorimetric data on thermokinetics and pressure were used for explaining the practical consequences or which the worst cases encountered in this kind of plant. Acceptable risk associated with emergency relief system design is vital for a plant producing organic peroxide. These basic data for designing an inherently safer plant can be conducted from adiabatic calorimetry. An encouraging deduction has been drawn here, these incidents may be avoided by the implementation of API RP 520, API RP 521, DIERS technology, OSHA 1910.119 and AIChE's CCPS recommended PSM elements.

Energy policy responses to the climate change challenge: The consistency of European CHP, renewables and energy efficiency policies

International Nuclear Information System (INIS)

Grohnheit, P.E.

1999-09-01

This report is Volume 14 of individual reports of the Shared Analysis Project prepared for the European Commission, Directorate General for Energy. The three major objectives of the project were: to design a common framework of energy analysis that aimed to involve all Member States and the experts of industrial research groups (the shared approach to energy analysis); To analyse generic EU-wide issues important for energy policy and for future energy demand and production, putting particular emphasis on world energy market trends, strategic energy policy responses to the Kyoto process, and evaluation of response strategies to increasing energy import dependence and to climate change activities; to carry out quantitative analyses of energy trends and scenarios as an input for discussion. The present volume considers three main issues concerning energy policy responses to the climate change challenge: the penetration of CHP and renewables according to official objectives, focusing on infrastructure and institutions rather than technology; the consistency of promotion of CHP, renewables and energy savings at the same time; consumers' choices and priorities in a liberalised market. The volume describes examples of policies in several Member States for these technologies with emphasis on CHP for both large-scale and small-scale district heating systems. The penetration of CHP technologies is analysed quantitatively using a traditional optimisation model approach for stylised regions with heat markets suitable for CHP and facing a competitive European market for electricity. The Joint Final Report of the project, titled 'Economic Foundations for Energy Policy' is published as a Special Issue of Energy in Europe, December 1999. All reports are available on the Internet, www.shared-analysis.fhg.de/ The project started in January 1998, involving about 100 months of scientific labour. The project consortium consisted of nine member institutes co-ordinated by the Fraunhofer

Economic feasibility of CHP facilities fueled by biomass from unused agriculture land

DEFF Research Database (Denmark)

Pfeifer, Antun; Dominkovic, Dominik Franjo; Ćosić, Boris

2016-01-01

In this paper, the energy potential of biomass from growing short rotation coppice on unused agricultural land in the Republic of Croatia is used to investigate the feasibility of Combined Heat and Power (CHP) facilities fueled by such biomass. Large areas of agricultural land that remain unused...

Development of a Wood Powder Fuelled 35 kW Stirling CHP Unit

DEFF Research Database (Denmark)

Pålsson, M.; Carlsen, Henrik

2003-01-01

For biomass fuelled CHP in sizes below 100 kW, Stirling engines are the only feasible alternative today. Using wood powder as fuel, the Stirling engine can be heated directly by the flame like when using a gaseous or liquid fuel burner. However, the combustion chamber will have to be much larger...... recirculation (CGR) a smaller air preheater can be used, while system efficiency will increase compared with using excess air for flame cooling. In a three-year project, a wood powder fuelled Stirling engine CHP unit will be developed and run in field test. The project will use the double-acting four......-cylinder Stirling engine SM3D with an electric output of 35 kW. This engine is a further development of the engine SM3B that has been developed at the Technical University of Denmark. The engine heater is being adapted for use with wood powder as fuel. During a two-year period a combustion system for this engine...

Economic potentials of CHP connected to district heat systems in Germany. Implementation of the EU Efficiency Directive

International Nuclear Information System (INIS)

Eikmeier, Bernd

2015-01-01

The EU Efficiency Directive (2012/27/EU) is requiring all member states to carry out an evaluation of the potential for highly efficient CHP and the efficient use of district heating and cooling by December 2015. The German Federal Ministry of Economic Affairs and Energy appointed this task to the Fraunhofer Institute for Manufacturing and Advanced Materials, division for Energy Systems Analysis (formerly Bremer Energie Institut) in conjunction with other partners. The results for the sector district- and communal heating with CHP, sub-sectors private households, trade and services industry, are presented in this article.

EFFICIENCY OF THE USE OF HEAT PUMPS ON THE CHP PLANTS

Directory of Open Access Journals (Sweden)

Juravleov A.A.

2007-04-01

Full Text Available The work is dedicated to the calculus of the efficiency of the use of heat pumps on the CHP plants. There are presented the interdependences between the pay-back period and NPV of heat pump and the price of 1 kWt of thermal power of heat pump and of the tariff of electricity.

Energetic and exergetic efficiencies of coal-fired CHP (combined heat and power) plants used in district heating systems of China

International Nuclear Information System (INIS)

Liao, Chunhui; Ertesvåg, Ivar S.; Zhao, Jianing

2013-01-01

The efficiencies of coal-fired CHP (combined heat and power) plants used in the district heating systems of China were analyzed with a thermodynamic model in the Hysys program. The influences of four parameters were evaluated by the Taguchi method. The results indicated that the extraction steam flow rate and extraction steam pressure are the most important parameters for energetic and exergetic efficiencies, respectively. The relations between extraction steam flow rate, extraction steam pressure and the energetic and exergetic efficiencies were investigated. The energetic and exergetic efficiencies were compared to the RPES (relative primary energy savings) and the RAI (relative avoided irreversibility). Compared to SHP (separate heat and power) generation, the CHP systems save fuel energy when extraction ratio is larger than 0.15. In the analysis of RAI, the minimum extraction ratio at which CHP system has advantages compared with SHP varies between 0.25 and 0.6. The higher extraction pressure corresponds to a higher value. Two of the examined plants had design conditions giving RPES close to zero and negative RAI. The third had both positive RPES and RAI at design conditions. The minimum extraction ratio can be used as an indicator to design or choose CHP plant for a given district heating system. - Highlights: • Extraction flow rate and extraction pressure are the most important parameters. • The exergetic efficiency depends on the energy to exergy ratio and system boundary. • The minimum extraction ratio is a key indicator for CHP plants. • Program Hysys and Taguchi method are used in this research

Optimal stochastic scheduling of CHP-PEMFC, WT, PV units and hydrogen storage in reconfigurable micro grids considering reliability enhancement

International Nuclear Information System (INIS)

Bornapour, Mosayeb; Hooshmand, Rahmat-Allah; Khodabakhshian, Amin; Parastegari, Moein

2017-01-01

Highlights: • Stochastic model is proposed for coordinated scheduling of renewable energy sources. • The effect of combined heat and power is considered. • Uncertainties of wind speed, solar radiation and electricity market price are considered. • Profit maximization, emission and AENS minimization are considered as objective functions. • Modified firefly algorithm is employed to solve the problem. - Abstract: Nowadays the operation of renewable energy sources and combined heat and power (CHP) units is increased in micro grids; therefore, to reach optimal performance, optimal scheduling of these units is required. In this regard, in this paper a micro grid consisting of proton exchange membrane fuel cell-combined heat and power (PEMFC-CHP), wind turbines (WT) and photovoltaic (PV) units, is modeled to determine the optimal scheduling state of these units by considering uncertain behavior of renewable energy resources. For this purpose, a scenario-based method is used for modeling the uncertainties of electrical market price, the wind speed, and solar irradiance. It should be noted that the hydrogen storage strategy is also applied in this study for PEMFC-CHP units. Market profit, total emission production, and average energy not supplied (AENS) are the objective functions considered in this paper simultaneously. Consideration of the above-mentioned objective functions converts the proposed problem to a mixed integer nonlinear programming. To solve this problem, a multi-objective firefly algorithm is used. The uncertainties of parameters convert the mixed integer nonlinear programming problem to a stochastic mixed integer nonlinear programming problem. Moreover, optimal coordinated scheduling of renewable energy resources and thermal units in micro-grids improve the value of the objective functions. Simulation results obtained from a modified 33-bus distributed network as a micro grid illustrates the effectiveness of the proposed method.

An assessment of the present and future opportunities for combined heat and power with district heating (CHP-DH) in the United Kingdom

International Nuclear Information System (INIS)

Kelly, Scott; Pollitt, Michael

2010-01-01

As global fuel reserves are depleted, alternative and more efficient forms of energy generation and delivery will be required. Combined heat and power with district heating (CHP-DH) provides an alternative energy production and delivery mechanism that is less resource intensive, more efficient and provides greater energy security than many popular alternatives. It will be shown that the economic viability of CHP-DH networks depends on several principles, namely (1) the optimisation of engineering and design principles; (2) organisational and regulatory frameworks; (3) financial and economic factors. It was found that in the long term DH is competitive with other energy supply and distribution technologies such as electricity and gas. However, in the short to medium term it is shown that economic risk, regulatory uncertainty and lock-in of existing technology are the most significant barriers to CHP-DH development. This research suggests that under the present regulatory and economic paradigm, the infrastructure required for DH networks remains financially prohibitive; the implementation of government policies are complicated and impose high transaction costs, while engineering solutions are frequently not implemented or economically optimised. If CHP-DH is going to play any part in meeting climate change targets then collaboration between public and private organisations will be required. It is clear from this analysis that strong local government involvement is therefore necessary for the co-ordination, leadership and infrastructural deployment of CHP-DH.

Large-Scale Combined Heat and Power (CHP) Generation at Loviisa Nuclear Power Plant Unit 3

International Nuclear Information System (INIS)

Bergroth, N.

2010-01-01

Fortum has applied for a Decision in Principle concerning the construction of a new nuclear power plant unit (Loviisa 3) ranging from 2800-4600 MWth at its site located at the southern coast of Finland. An attractive alternative investigated is a co-generation plant designed for large-scale district heat generation for the Helsinki metropolitan area that is located approximately 75 km west of the site. The starting point is that the district heat generation capacity of 3 unit would be around 1 000 MWth.The possibility of generating district heat for the metropolitan area by Loviisa's two existing nuclear power plant units was investigated back in the 1980s, but it proved unpractical at the time. With the growing concern of the climate change and the subsequent requirements on heat and power generation, the idea is much more attractive today, when recognising its potential to decrease Finland's carbon dioxide emissions significantly. Currently the district heat generation in metropolitan area is based on coal and natural gas, producing some five to seven million tonnes of carbon dioxide emissions annually. Large-scale combined heat and power (CHP) generation at the 3 unit could cut this figure by up to four million tonnes. This would decrease carbon dioxide emissions by as much as six percent. In addition, large-scale CHP generation would increase the overall efficiency of the new unit significantly and hence, reduce the environmental impact on the local marine environment by cutting heat discharges into the Gulf of Nuclear energy has been used for district heating in several countries both in dedicated nuclear heating plants and in CHP generation plants. However, the heat generation capacity is usually rather limited, maximum being around 250 MWth per unit. Set against this, the 3 CHP concept is much more ambitious, not only because of the much larger heat generation output envisaged, but also because the district heating water would have to be transported over a

Stirling Energy Module (SEM) as Micro-CHP; Stirling Energy Module (SEM) als Mini-BHKW

Energy Technology Data Exchange (ETDEWEB)

Schlegel, A.

2006-07-01

Since many years, a lot of effort is being put into the development of combined heat and power units (CHP) for the decentralised production of electric power. For long time, the main focus was on fuel cells. In the meantime, the Stirling technology, which is based upon classical mechanical engineering and innovative technical concepts, proceeded in its development as well. The following article describes the technology and the actual state of the development of the Stirling Energy Module (SEM) for the application as Micro-CHP in one-family-houses. SEM is based on a free-piston engine with a linear power generator, producing electric power while heating. The Stirling engine is planned the be introduced into the market as a replacement for the conventional heating systems within a couple of years. (author)

Incremental short daily home hemodialysis: a case series

OpenAIRE

Toth-Manikowski, Stephanie M.; Mullangi, Surekha; Hwang, Seungyoung; Shafi, Tariq

2017-01-01

Background Patients starting dialysis often have substantial residual kidney function. Incremental hemodialysis provides a hemodialysis prescription that supplements patients? residual kidney function while maintaining total (residual + dialysis) urea clearance (standard Kt/Vurea) targets. We describe our experience with incremental hemodialysis in patients using NxStage System One for home hemodialysis. Case presentation From 2011 to 2015, we initiated 5 incident hemodialysis patients on an ...

Economic dispatch of a single micro-gas turbine under CHP operation

International Nuclear Information System (INIS)

Rist, Johannes F.; Dias, Miguel F.; Palman, Michael; Zelazo, Daniel; Cukurel, Beni

2017-01-01

Highlights: •Economic dispatch of a micro gas turbine is considered for smart grid integration. •A detailed thermodynamic cycle analysis is conducted for variable load CHP operation. •Benefits are shown for case studies with real demand profiles and energy tariffs. •Optimal unit schedule can be electricity, heat, revenue or maintenance-cost driven. -- Abstract: This work considers the economic dispatch of a single micro-gas turbine under combined heat and power (CHP) operation. A detailed thermodynamic cycle analysis is conducted on a representative micro-gas turbine unit with non-constant component efficiencies and recuperator bypass. Based on partial and full load configurations, an accurate optimization model is developed for solving the economic dispatch problem of integrating the turbine into the grid. The financial benefit and viability of this approach is then examined on four detailed scenarios using real data on energy demand profiles and electricity tariffs. The analysis considers the optimal operation in a large hotel, a full-service restaurant, a small hotel, and a residential neighborhood during various seasons. The optimal schedule follows four fundamental economic drivers which are electricity, heat, revenue, and maintenance-cost driven.

An energetic-exergetic analysis of a residential CHP system based on PEM fuel cell

International Nuclear Information System (INIS)

Barelli, L.; Bidini, G.; Gallorini, F.; Ottaviano, A.

2011-01-01

Highlights: → A zero-dimensional of a micro cogenerative (CHP) energy system based on a Proton Exchange Membrane fuel cell (PEMFC) has been developed. → The electrochemical model has been validated with experimental data. → The performances of this CHP system have been evaluated through a series of simulations. → An energy/exergy analysis of the simulation results has allowed to define the PEMFC optimal operating conditions. → The PEMFC optimal operating conditions detected are: 1 atm, 353.15 K and 100% RH. -- Abstract: The use of fuel cell systems for distributed residential power generation represents an interesting alternative to traditional thermoelectric plants due to their high efficiency and the potential recovering of the heat generated by the internal electrochemical reactions. In this paper the study of a micro cogenerative (CHP) energy system based on a Proton Exchange Membrane fuel cell (PEMFC) is reported. With the aim to evaluate the performance and then the feasibility of this non-conventional energy system, in consideration of thermal and electrical basic demand of a multifamily apartment blocks, a zero-dimensional PEMFC model in Aspen Plus environment has been developed. A simulations sequence has been carried out at different operating conditions of the fuel cell (varying temperature, pressure and relative humidity). Subsequently, on the basis of the obtained results, an energy/exergy analysis has been conducted to define the optimal operating conditions of the PEMFC that ensures the most efficient use of the energy and exergy inputs.

Energy policy responses to the climate change challenge: The consistency of European CHP, renewables and energy efficiency policies

Energy Technology Data Exchange (ETDEWEB)

Grohnheit, P.E.

1999-09-01

This report is Volume 14 of individual reports of the Shared Analysis Project prepared for the European Commission, Directorate General for Energy. The three major objectives of the project were: to design a common framework of energy analysis that aimed to involve all Member States and the experts of industrial research groups (the shared approach to energy analysis); To analyse generic EU-wide issues important for energy policy and for future energy demand and production, putting particular emphasis on world energy market trends, strategic energy policy responses to the Kyoto process, and evaluation of response strategies to increasing energy import dependence and to climate change activities; to carry out quantitative analyses of energy trends and scenarios as an input for discussion. The present volume considers three main issues concerning energy policy responses to the climate change challenge: the penetration of CHP and renewables according to official objectives, focusing on infrastructure and institutions rather than technology; the consistency of promotion of CHP, renewables and energy savings at the same time; consumers' choices and priorities in a liberalised market. The volume describes examples of policies in several Member States for these technologies with emphasis on CHP for both large-scale and small-scale district heating systems. The penetration of CHP technologies is analysed quantitatively using a traditional optimisation model approach for stylised regions with heat markets suitable for CHP and facing a competitive European market for electricity. The Joint Final Report of the project, titled 'Economic Foundations for Energy Policy' is published as a Special Issue of Energy in Europe, December 1999. All reports are available on the Internet, www.shared-analysis.fhg.de/ The project started in January 1998, involving about 100 months of scientific labour. The project consortium consisted of nine member institutes co-ordinated by

A MATHEMATICAL MODEL OF CHP 2000 TYPE PROGRESSIVE GEAR

Directory of Open Access Journals (Sweden)

Paweł Lonkwic

2016-12-01

Full Text Available The project of CHP2000 type progressive gear has been presented in the article. The offered solution from its construction point of view differs from the existing solutions due to the application of Belleville springs packets supporting the braking roller cam and achieving a flexible range of the gear loading. The standard concept of the gear loading within a mathematical and a geometrical model has been presented in the article. The proposed solution can be used in the friction lifts with the loading capacity from 8500 up to 20000 N.

Calculation of the increment reduction in spruce stands by charcoal smoke

Energy Technology Data Exchange (ETDEWEB)

Guede, J

1954-01-01

Chronic damage to spruce trees by charcoal smoke, often hardly noticeable from outward appearance but causing marked reductions of wood increment can be determined by means of a calculation by increment cores. Sulfurous acid anhydride causes the closure of the stomates of needles by which the circulation of water is checked. The assimilation and the wood increment are reduced. The cores are taken from uninjured trees belonging to the dominant class. These trees are liable to irregular variations in the trend of growth only by atmospheric influences and disturbances in the circulation of water. The decrease of increment of a stand can be judged by the trend of growth of the basal area of sample trees. Two methods are applied: in the first method, the difference between the mean total increment before the damage has been caused and that after it is calculated by the yield table in deriving the site quality classes from the basal area growth of dominant stems. This is possible by using the mean diameter of each age class and the frequency curve of basal area for each site class. In the other method, the reduction of basal area increment of sample trees is measured directly. The total reduction of a stand can be judged by the share of the dominant class of stem in the total current growth of the basal area of a sound stand and by the percent of reduction of the sample trees.

Optimal fuel-mix in CHP plants under a stochastic permit price. Risk-neutrality versus risk-aversion

International Nuclear Information System (INIS)

Lappi, Pauli; Ollikka, Kimmo; Ollikainen, Markku

2010-01-01

This paper studies the optimal fuel-mix of a CHP producer under emission permit price risk. The producer's multi-fuel plant uses two CO 2 -intensive fuels and one clean fuel. Using a mean-variance framework we develop three models. The models are divided into spot-models (risk neutral and risk averse cases) and a forward-model (risk averse case). We derive the effects of price risk on optimal fuel use. An increase in price risk can in fact increase the use of CO 2 -intensive fuel in the spot-model. In the forward-model, the production and financial decisions are separate. We also evaluate the risk-bearing behavior of seven Finnish CHP producers. We found that risk-neutrality describes behavior better than risk-aversion. (author)

Economic feasibility of CHP facilities fueled by biomass from unused agriculture land: Case of Croatia

International Nuclear Information System (INIS)

Pfeifer, Antun; Dominković, Dominik Franjo; Ćosić, Boris; Duić, Neven

2016-01-01

Highlights: • Potential of unused agricultural land for biomass and fruit production is assessed. • Technical and energy potential of biomass from SRC and fruit pruning is calculated. • Economic feasibility of CHP plants utilizing biomass from SRC is presented for Croatia. • Sensitivity analysis and recommendations for shift toward feasibility are provided. - Abstract: In this paper, the energy potential of biomass from growing short rotation coppice on unused agricultural land in the Republic of Croatia is used to investigate the feasibility of Combined Heat and Power (CHP) facilities fueled by such biomass. Large areas of agricultural land that remain unused for food crops, represent significant potential for growing biomass that could be used for energy. This biomass could be used to supply power plants of up to 15 MW_e in accordance with heat demands of the chosen locations. The methodology for regional energy potential assessment was elaborated in previous work and is now used to investigate the conditions in which such energy facilities could be feasible. The overall potential of biomass from short rotation coppice cultivated on unused agricultural land in the scenarios with 30% of the area is up to 10 PJ/year. The added value of fruit trees pruning biomass represents an incentive for the development of fruit production on such agricultural land. Sensitivity analysis was conducted for several parameters: cost of biomass, investment costs in CHP systems and combined change in biomass and technology cost.

Implementing Kernel Methods Incrementally by Incremental Nonlinear Projection Trick.

Science.gov (United States)

Kwak, Nojun

2016-05-20

Recently, the nonlinear projection trick (NPT) was introduced enabling direct computation of coordinates of samples in a reproducing kernel Hilbert space. With NPT, any machine learning algorithm can be extended to a kernel version without relying on the so called kernel trick. However, NPT is inherently difficult to be implemented incrementally because an ever increasing kernel matrix should be treated as additional training samples are introduced. In this paper, an incremental version of the NPT (INPT) is proposed based on the observation that the centerization step in NPT is unnecessary. Because the proposed INPT does not change the coordinates of the old data, the coordinates obtained by INPT can directly be used in any incremental methods to implement a kernel version of the incremental methods. The effectiveness of the INPT is shown by applying it to implement incremental versions of kernel methods such as, kernel singular value decomposition, kernel principal component analysis, and kernel discriminant analysis which are utilized for problems of kernel matrix reconstruction, letter classification, and face image retrieval, respectively.

Spatial distribution of pollutants in the area of the former CHP plant

Science.gov (United States)

Cichowicz, Robert

2018-01-01

The quality of atmospheric air and level of its pollution are now one of the most important issues connected with life on Earth. The frequent nuisance and exceedance of pollution standards often described in the media are generated by both low emission sources and mobile sources. Also local organized energy emission sources such as local boiler houses or CHP plants have impact on air pollution. At the same time it is important to remember that the role of local power stations in shaping air pollution immission fields depends on the height of emitters and functioning of waste gas treatment installations. Analysis of air pollution distribution was carried out in 2 series/dates, i.e. 2 and 10 weeks after closure of the CHP plant. In the analysis as a reference point the largest intersection of streets located in the immediate vicinity of the plant was selected, from which virtual circles were drawn every 50 meters, where 31 measuring points were located. As a result, the impact of carbon dioxide, hydrogen sulfide and ammonia levels could be observed and analyzed, depending on the distance from the street intersection.

Elimination of restraints on the propagation of combined heat and power (CHP) generation systems in Switzerland; Beseitigung von Hemmnissen bei der Verbreitung von Waermekraftkopplung (WKK) in der Schweiz

Energy Technology Data Exchange (ETDEWEB)

Rieder, S.; Landis, F. [Interface Politikstudien Forschung Beratung, Luzern (Switzerland); Lienhard, A.; Marti Locher, F. [Universitaet Bern, Kompetenzzentrum fuer Public Management (KPM), Bern (Switzerland); Krummenacher, S. [Enerprice Partners AG, Technopark Luzern, Root Laengenbold (Switzerland)

2009-04-15

This report for the Swiss Federal Office of Energy (SFOE) discusses the results of study initiated by the SFOE that was to investigate the reasons for the low level of proliferation of CHP technology in Switzerland. The two main questions asked - which factors inhibit the use of CHP in particular application areas and which energy-policy measures can remove such obstacles - are discussed. The use of CHP in various areas of application from waste incineration plants through to units used in residential buildings is analysed and commented on. Recommendations on measures that can be taken to enhance the use of CHP are discussed. Three strategy variants available to the public services area are presented and discussed. It is noted that a consensus between players in the technical and political areas is necessary

CHP and Local Governments: Case Studies and EPA’s New Guide (Webinar) – September 30, 2014

Science.gov (United States)

This webinar presents two case studies of CHP development projects undertaken through cooperation between private companies and government entities, and introduces an EPA guide to assist local governments to reduce greenhouse gas (GHG) emissions.

Assessment of the implementation issues for fuel cells in domestic and small scale stationary power generation and CHP applications

Energy Technology Data Exchange (ETDEWEB)

Graham, G.; Cruden, A.; Hart, J.

2002-07-01

This report discusses implementation issues associated with the use of fuel cells in <10 kW domestic, small-scale power generation and combined heat and power (CHP) operations in the UK. The report examines the key issues (fuel cell system standards and certification, fuel infrastructure, commercial issues and competing CHP technologies), before discussing non-technical issues including finance, ownership, import and export configuration, pricing structure, customer acceptability, installation, operation and training of servicing and commissioning personnel. The report goes on to discuss market and technical drivers, grid connection issues and solutions, operations and maintenance. Recommendations for the future are made.

Optimal fuel-mix in CHP plants under a stochastic permit price. Risk-neutrality versus risk-aversion

Energy Technology Data Exchange (ETDEWEB)

Lappi, Pauli; Ollikka, Kimmo; Ollikainen, Markku [Department of Economics and Management, P.O. Box 27, University of Helsinki, FIN-00014 Helsinki (Finland)

2010-02-15

This paper studies the optimal fuel-mix of a CHP producer under emission permit price risk. The producer's multi-fuel plant uses two CO{sub 2}-intensive fuels and one clean fuel. Using a mean-variance framework we develop three models. The models are divided into spot-models (risk neutral and risk averse cases) and a forward-model (risk averse case). We derive the effects of price risk on optimal fuel use. An increase in price risk can in fact increase the use of CO{sub 2}-intensive fuel in the spot-model. In the forward-model, the production and financial decisions are separate. We also evaluate the risk-bearing behavior of seven Finnish CHP producers. We found that risk-neutrality describes behavior better than risk-aversion. (author)

Optimal fuel-mix in CHP plants under a stochastic permit price: Risk-neutrality versus risk-aversion

Energy Technology Data Exchange (ETDEWEB)

Lappi, Pauli, E-mail: pauli.lappi@helsinki.f [Department of Economics and Management, P.O. Box 27, University of Helsinki, FIN-00014 Helsinki (Finland); Ollikka, Kimmo, E-mail: kimmo.ollikka@helsinki.f [Department of Economics and Management, P.O. Box 27, University of Helsinki, FIN-00014 Helsinki (Finland); Ollikainen, Markku, E-mail: markku.ollikainen@helsinki.f [Department of Economics and Management, P.O. Box 27, University of Helsinki, FIN-00014 Helsinki (Finland)

2010-02-15

This paper studies the optimal fuel-mix of a CHP producer under emission permit price risk. The producer's multi-fuel plant uses two CO{sub 2}-intensive fuels and one clean fuel. Using a mean-variance framework we develop three models. The models are divided into spot-models (risk neutral and risk averse cases) and a forward-model (risk averse case). We derive the effects of price risk on optimal fuel use. An increase in price risk can in fact increase the use of CO{sub 2}-intensive fuel in the spot-model. In the forward-model, the production and financial decisions are separate. We also evaluate the risk-bearing behavior of seven Finnish CHP producers. We found that risk-neutrality describes behavior better than risk-aversion.

Size, Stability and Incremental Budgeting Outcomes in Public Universities.

Science.gov (United States)

Schick, Allen G.; Hills, Frederick S.

1982-01-01

Examined the influence of relative size in the analysis of total dollar and workforce budgets, and changes in total dollar and workforce budgets when correlational/regression methods are used. Data suggested that size dominates the analysis of total budgets, and is not a factor when discretionary dollar increments are analyzed. (JAC)

Incremental short daily home hemodialysis: a case series.

Science.gov (United States)

Toth-Manikowski, Stephanie M; Mullangi, Surekha; Hwang, Seungyoung; Shafi, Tariq

2017-07-05

Patients starting dialysis often have substantial residual kidney function. Incremental hemodialysis provides a hemodialysis prescription that supplements patients' residual kidney function while maintaining total (residual + dialysis) urea clearance (standard Kt/Vurea) targets. We describe our experience with incremental hemodialysis in patients using NxStage System One for home hemodialysis. From 2011 to 2015, we initiated 5 incident hemodialysis patients on an incremental home hemodialysis regimen. The biochemical parameters of all patients remained stable on the incremental hemodialysis regimen and they consistently achieved standard Kt/Vurea targets. Of the two patients with follow-up >6 months, residual kidney function was preserved for ≥2 years. Importantly, the patients were able to transition to home hemodialysis without automatically requiring 5 sessions per week at the outset and gradually increased the number of treatments and/or dialysate volume as the residual kidney function declined. An incremental home hemodialysis regimen can be safely prescribed and may improve acceptability of home hemodialysis. Reducing hemodialysis frequency by even one treatment per week can reduce the number of fistula or graft cannulations or catheter connections by >100 per year, an important consideration for patient well-being, access longevity, and access-related infections. The incremental hemodialysis approach, supported by national guidelines, can be considered for all home hemodialysis patients with residual kidney function.

Modeling and optimization of a 1 kWe HT-PEMFC-based micro-CHP residential system

DEFF Research Database (Denmark)

Arsalis, Alexandros; Nielsen, Mads Pagh; Kær, Søren Knudsen

2012-01-01

A high temperature-proton exchange membrane (HT-PEMFC)-based micro-combined-heat-and-power (CHP) residential system is designed and optimized, using a genetic algorithm (GA) optimization strategy. The proposed system consists of a fuel cell stack, steam methane reformer (SMR) reactor, water gas...

Research, Development and Demonstration of Micro-CHP Systems for Residential Applications - Phase I

Energy Technology Data Exchange (ETDEWEB)

Robert A. Zogg

2011-03-14

The objective of the Micro-CHP Phase I effort was to develop a conceptual design for a Micro-CHP system including: Defining market potential; Assessing proposed technology; Developing a proof-of-principle design; and Developing a commercialization strategy. TIAX LLC assembled a team to develop a Micro-CHP system that will provide electricity and heating. TIAX, the contractor and major cost-share provider, provided proven expertise in project management, prime-mover design and development, appliance development and commercialization, analysis of residential energy loads, technology assessment, and market analysis. Kohler Company, the manufacturing partner, is a highly regarded manufacturer of standby power systems and other residential products. Kohler provides a compellingly strong brand, along with the capabilities in product development, design, manufacture, distribution, sales, support, service, and marketing that only a manufacturer of Kohler's status can provide. GAMA, an association of appliance and equipment manufacturers, provided a critical understanding of appliance commercialization issues, including regulatory requirements, large-scale market acceptance issues, and commercialization strategies. The Propane Education & Research Council, a cost-share partner, provided cost share and aided in ensuring the fuel flexibility of the conceptual design. Micro-CHP systems being commercialized in Europe and Japan are generally designed to follow the household thermal load, and generate electricity opportunistically. In many cases, any excess electricity can be sold back to the grid (net metering). These products, however, are unlikely to meet the demands of the U.S. market. First, these products generally cannot provide emergency power when grid power is lost--a critical feature to market success in the U.S. Even those that can may have insufficient electric generation capacities to meet emergency needs for many U.S. homes. Second, the extent to which net

In-situ corrosion investigation at Masnedø CHP plant - a straw-fired power plant

DEFF Research Database (Denmark)

Montgomery, Melanie; Karlsson, Asger

1999-01-01

Various austenitic and ferritic steels were exposed on a water-cooled probe in the superheater area of a straw-fired CHP plant. The temperature of the probe ranged from 450-600°C and the period of exposure was 1400 hours. The rate of corrosion was assessed based on unattacked metal remaining...

Identification of an operon, Pil-Chp, that controls twitching motility and virulence in Xylella fastidiosa.

Science.gov (United States)

Cursino, Luciana; Galvani, Cheryl D; Athinuwat, Dusit; Zaini, Paulo A; Li, Yaxin; De La Fuente, Leonardo; Hoch, Harvey C; Burr, Thomas J; Mowery, Patricia

2011-10-01

Xylella fastidiosa is an important phytopathogenic bacterium that causes many serious plant diseases, including Pierce's disease of grapevines. Disease manifestation by X. fastidiosa is associated with the expression of several factors, including the type IV pili that are required for twitching motility. We provide evidence that an operon, named Pil-Chp, with genes homologous to those found in chemotaxis systems, regulates twitching motility. Transposon insertion into the pilL gene of the operon resulted in loss of twitching motility (pilL is homologous to cheA genes encoding kinases). The X. fastidiosa mutant maintained the type IV pili, indicating that the disrupted pilL or downstream operon genes are involved in pili function, and not biogenesis. The mutated X. fastidiosa produced less biofilm than wild-type cells, indicating that the operon contributes to biofilm formation. Finally, in planta the mutant produced delayed and less severe disease, indicating that the Pil-Chp operon contributes to the virulence of X. fastidiosa, presumably through its role in twitching motility.

Feasibility study of a Thermo-Photo-Voltaic system for CHP application in residential buildings

International Nuclear Information System (INIS)

Bianchi, Michele; Ferrari, Claudio; Melino, Francesco; Peretto, Antonio

2012-01-01

Highlights: ► The profitability of Thermo-Photo-Voltaic generator systems for a single-family dwelling is analyzed. ► Heat and electricity load profiles depending on hour of the day are considered for an entire year. ► The effect of Thermo-Photo-Voltaic generator size is evaluated for different household utilities. ► Results allow to identify the conditions for the energetic and economic convenience of Thermo-Photo-Voltaic system. -- Abstract: The growing demand of energy coupled with an increasing attention to the environmental impact have forced, in the last decades, toward the study and the development of new strategies in order to reduce primary energy consumptions. The cogeneration (CHP) and the on-site generation (also known as distributed generation) could be the key strategy to achieve this goal; CHP systems allow to reduce the fuel consumption and pollutant emissions (in particular the greenhouse gases) compared to separate generation; moreover on-site-generation contributes to the reduction of the energy which is lost in electricity transmission, and increases the security in the energy supply. In this scenario the Thermo-Photo-Voltaic generation (TPV) is obtaining an increasing attention; TPV is a system to convert into electrical energy the radiation emitted from an artificial heat source (i.e. the combustion of fuel) by the use of photovoltaic cells. A domestic gas furnace based on this technology can provide the entire thermal need of an apartment and can also contributes to satisfy the electrical demand. The aim of this study is the understanding of the behavior of a TPV in CHP application in case of residential buildings, under both the energetic and economical point of view; in particular a parametrical analysis is developed and discussed varying the TPV electrical efficiency, the thermal request and the apartment typology.

Energy efficiency analysis and impact evaluation of the application of thermoelectric power cycle to today's CHP systems

DEFF Research Database (Denmark)

Chen, Min; Lund, Henrik; Rosendahl, Lasse

2010-01-01

benefits, together with the environmental impact of this deployment, will then be estimated. By using the Danish thermal energy system as a paradigm, this paper will consider the TEG application to district heating systems and power plants through the EnergyPLAN model, which has been created to design......High efficiency thermoelectric generators (TEG) can recover waste heat from both industrial and private sectors. Thus, the development and deployment of TEG may represent one of the main drives for technological change and fuel substitution. This paper will present an analysis of system efficiency...... configurations for combustion systems. The feasible deployment of TEG in various CHP plants will be examined in terms of heat source temperature range, influences on CHP power specification and thermal environment, as well as potential benefits. The overall conversion efficiency improvements and economic...

Multi-period MINLP model for optimising operation and structural changes to CHP plants in district heating networks with long-term thermal storage

International Nuclear Information System (INIS)

Tveit, Tor-Martin; Savola, Tuula; Gebremedhin, Alemayehu; Fogelholm, Carl-Johan

2009-01-01

By using thermal storages it is possible to decouple the generation of power and heat, and it can also lead to an reduction in investments, as the storage can be used to cover the peak load periods. This work presents a MINLP model that can be used for analysing new investments and the long-term operation of CHP plants in a district heating network with long-term thermal storage. The model presented in this work includes the non-linear off-design behaviour of the CHP plants as well as a generic mathematical model of the thermal storage, without the need to fix temperatures and pressure. The model is formulated in such a way that it is suitable for deterministic MINLP solvers. The model is non-convex, and subsequently global optimality cannot be guaranteed with local solvers. In order to reduce the chance of obtaining a poor local optimum compared to the global optimum, the model should be solved many times with the initial values varying randomly. It is possible to extract a lot of results from the model, for instance total annual profit, the optimal selection of process options, mass flow through the plant, and generated power from each plant. The formulation of the model makes it suitable for deterministic MINLP solvers

A price mechanism for supply demand matching in local grid of households with micro-CHP

NARCIS (Netherlands)

Larsen, G.K.H.; van Foreest, N.D.; Scherpen, J.M.A.

2012-01-01

This paper describes a dynamic price mechanism to coordinate eletric power generation from micro Combined Heat and Power (micro-CHP) systems in a network of households. It is assumed that the households are prosumers, i.e. both producers and consumers of electricity. The control is done on household

Modeling and parametric study of a 1 kWe HT-PEMFC-based residential micro-CHP system

DEFF Research Database (Denmark)

Arsalis, Alexandros; Nielsen, Mads Pagh; Kær, Søren Knudsen

2011-01-01

A detailed thermodynamic, kinetic and geometric model of a micro-CHP (Combined-Heatand-Power) residential system based on High Temperature-Proton Exchange Membrane Fuel Cell (HT-PEMFC) technology is developed, implemented and validated. HT-PEMFC technology is investigated as a possible candidate...

Fuel cell power plants for decentralised CHP applications

International Nuclear Information System (INIS)

Ohmer, Martin; Mattner, Katja

2015-01-01

Fuel cells are the most efficient technology to convert chemical energy into electricity and heat and thus they could have a major impact on reducing fuel consumption, CO 2 and other emissions (NO x , SO x and particulate matter). Fired with natural or biogas and operated with an efficiency of up to 49 % a significant reduction of fuel costs can be achieved in decentralised applications. Combined heat and power (CHP) configurations add value for a wide range of industrial applications. The exhaust heat of approximately 400 C can be utilised for heating purposes and the production of steam. Besides, it can be also fed directly to adsorption cooling systems. With more than 110 fuel cell power plants operating worldwide, this technology is a serious alternative to conventional gas turbines or gas engines.

Dental caries increments and related factors in children with type 1 diabetes mellitus.

Science.gov (United States)

Siudikiene, J; Machiulskiene, V; Nyvad, B; Tenovuo, J; Nedzelskiene, I

2008-01-01

The aim of this study was to analyse possible associations between caries increments and selected caries determinants in children with type 1 diabetes mellitus and their age- and sex-matched non-diabetic controls, over 2 years. A total of 63 (10-15 years old) diabetic and non-diabetic pairs were examined for dental caries, oral hygiene and salivary factors. Salivary flow rates, buffer effect, concentrations of mutans streptococci, lactobacilli, yeasts, total IgA and IgG, protein, albumin, amylase and glucose were analysed. Means of 2-year decayed/missing/filled surface (DMFS) increments were similar in diabetics and their controls. Over the study period, both unstimulated and stimulated salivary flow rates remained significantly lower in diabetic children compared to controls. No differences were observed in the counts of lactobacilli, mutans streptococci or yeast growth during follow-up, whereas salivary IgA, protein and glucose concentrations were higher in diabetics than in controls throughout the 2-year period. Multivariable linear regression analysis showed that children with higher 2-year DMFS increments were older at baseline and had higher salivary glucose concentrations than children with lower 2-year DMFS increments. Likewise, higher 2-year DMFS increments in diabetics versus controls were associated with greater increments in salivary glucose concentrations in diabetics. Higher increments in active caries lesions in diabetics versus controls were associated with greater increments of dental plaque and greater increments of salivary albumin. Our results suggest that, in addition to dental plaque as a common caries risk factor, diabetes-induced changes in salivary glucose and albumin concentrations are indicative of caries development among diabetics. Copyright 2008 S. Karger AG, Basel.

Micro CHP as a new business model. Trianel distribution system decentralised production; Mikro-BHKW als neues Geschaeftsmodell. Trianel-Netzwerk Dezentrale Erzeugung

Energy Technology Data Exchange (ETDEWEB)

Nicolai, Michel [Trianel GmbH, Aachen (Germany)

2013-04-29

About four years ago, an energy distribution company in Hamburg (Federal Republic of Germany) reported on mini and micro CHP in the media. When it comes to a decentralized production of electricity and heat, however public utilities are the perfect partner: the decentralized power generation in flexible adjustable combined heat and power plants offers the opportunity to provide highly efficient heat and power directly at the place of consumption. In addition, regional and municipal utilities score with the theme mini and micro CHP for their customers due to the support on the way to more energy efficiency.

A Compound Herbal Preparation (CHP) in the Treatment of Children with ADHD: A Randomized Controlled Trial

Science.gov (United States)

Katz, M.; Adar Levine, A.; Kol-Degani, H.; Kav-Venaki, L.

2010-01-01

Objective: Evaluation of the efficacy of a patented, compound herbal preparation (CHP) in improving attention, cognition, and impulse control in children with ADHD. Method: Design: A randomized, double-blind, placebo-controlled trial. Setting: University-affiliated tertiary medical center. Participants: 120 children newly diagnosed with ADHD,…

Modelling the Italian household sector at the municipal scale: Micro-CHP, renewables and energy efficiency

International Nuclear Information System (INIS)

Comodi, Gabriele; Cioccolanti, Luca; Renzi, Massimiliano

2014-01-01

This study investigates the potential of energy efficiency, renewables, and micro-cogeneration to reduce household consumption in a medium Italian town and analyses the scope for municipal local policies. The study also investigates the effects of tourist flows on town's energy consumption by modelling energy scenarios for permanent and summer homes. Two long-term energy scenarios (to 2030) were modelled using the MarkAL-TIMES generator model: BAU (business as usual), which is the reference scenario, and EHS (exemplary household sector), which involves targets of penetration for renewables and micro-cogeneration. The analysis demonstrated the critical role of end-use energy efficiency in curbing residential consumption. Cogeneration and renewables (PV (photovoltaic) and solar thermal panels) were proven to be valuable solutions to reduce the energetic and environmental burden of the household sector (−20% in 2030). Because most of household energy demand is ascribable to space-heating or hot water production, this study finds that micro-CHP technologies with lower power-to-heat ratios (mainly, Stirling engines and microturbines) show a higher diffusion, as do solar thermal devices. The spread of micro-cogeneration implies a global reduction of primary energy but involves the internalisation of the primary energy, and consequently CO 2 emissions, previously consumed in a centralised power plant within the municipality boundaries. - Highlights: • Energy consumption in permanent homes can be reduced by 20% in 2030. • High efficiency appliances have different effect according to their market penetration. • Use of electrical heat pumps shift consumption from natural gas to electricity. • Micro-CHP entails a global reduction of energy consumption but greater local emissions. • The main CHP technologies entering the residential market are Stirling and μ-turbines

Advanced m-CHP fuel cell system based on a novel bio-ethanol fluidized bed membrane reformer

NARCIS (Netherlands)

Viviente, J.L.; Melendez Rey, J.; Pacheco Tanaka, D.A.; Gallucci, F.; Spallina, V.; Manzolini, G.; Foresti, S.; Palma, V.; Ruocco, C.; Roses, L.

2017-01-01

Distributed power generation via Micro Combined Heat and Power (m-CHP) systems, has been proven to over-come disadvantages of centralized generation since it can give savings in terms of Primary Energy consumption and energy costs. The FluidCELL FCH JU/FP7 project aims at providing the Proof of

Experimental study and modelling of degradation phenomena in HTPEM fuel cell stacks for use in CHP systems

DEFF Research Database (Denmark)

Andreasen, Søren Juhl

2009-01-01

Degradation phenomena in HTPEM fuel cells for use in CHP systems were investigated experimentally and by modelling. It was found that the two main degradation mechanisms in HTPEM fuel cells are carbon corrosion and Pt agglomeration. On basis of this conclusion a mechanistic model, describing...

The Design, Construction, and Experimental Evaluation of a Compact Thermoacoustic-Stirling Engine Generator for Use in a micro-CHP Appliance

Science.gov (United States)

Wilcox, Douglas A., Jr.

Micro combined heat and power or micro-CHP is the simultaneous generation of useful heat and electricity on a residential scale. The heat and electricity are produced at the point of use, avoiding the distribution losses associated with a centralized power plant. These appliances combine a conventional gas-fired condensing boiler with an electric power module capable of generating electricity from the heat of combustion. Currently, the leading power modules for micro-CHP appliances are free-piston Stirling engines (FPSEs) which can generate 1050 watts of electricity at a thermal-to-electric efficiency of 26%.[1] These external combustion engines have been under development for the last 25 years, with FPSE micro-CHP appliances only recently being introduced to the commercial market. Publications by developers assert unlimited service life and high efficiency, with low noise and emissions; but despite these claims, the actual reliability and cost of manufacturing has prevented their successful mass-market adoption. A Thermoacoustic-Stirling Engine Generator or TaSEG is one possible alternative to FPSE's. A TaSEG uses a thermoacoustic engine, or acoustic heat engine, which can efficiently convert high temperature heat into acoustic power while maintaining a simple design with fewer moving parts than traditional FPSE's. This simpler engine is coupled to an electrodynamic alternator capable of converting acoustic power into electricity. This thesis outlines the design, construction, and experimental evaluation of a TaSEG which is appropriate for integration with a gas burner inside of a residential micro- CHP appliance. The design methodology is discussed, focusing on how changes in the geometry affected the predicted performance. Details of its construction are given and the performance of the TaSEG is then outlined. The TaSEG can deliver 132 watts of electrical output power to an electric load with an overall measured thermal-to-electric (first law) efficiency of eta

Renewables and CHP with District Energy in Support of Sustainable Communities

Energy Technology Data Exchange (ETDEWEB)

Snoek, Chris

2010-09-15

This paper addresses the powerful idea of connecting many energy users to environmentally optimum energy sources through integrated community energy systems. Such systems require piping networks for distributing thermal energy, i.e., district heating and cooling (DHC) systems. The possibilities and advantages of the application of integrated energy concepts are discussed, including the economic and environmental benefits of integrating localized electrical generating systems (CHP), transportation systems, industrial processes and other thermal energy requirements. Examples of a number of operating systems are provided. Some of the R and D carried out by the IEA Implementing Agreement on District Heating and Cooling is also described.

Energy versus economic effectiveness in CHP (combined heat and power) applications: Investigation on the critical role of commodities price, taxation and power grid mix efficiency

International Nuclear Information System (INIS)

Comodi, Gabriele; Rossi, Mosè

2016-01-01

Starting from PES (primary energy saving) and CSR (cost saving ratio) definitions the work pinpoints a “grey area” in which CHP (combined heat and power – cogeneration) units can operate with profit and negative PES. In this case, CHP can be profitably operated with lower efficiency with respect to separate production of electrical and thermal energy. The work defines the R-index as the ratio between the cost of fuel and electricity. The optimal value of R-index for which CHP units operate with both environmental benefit (PES > 0) and economic profitability (CSR > 0) is the reference value of electrical efficiency, η_e_l_-_r_e_f, of separate production (national power grid mix). As a consequence, optimal R-index varies from Country to Country. The work demonstrates that the value of R corresponds to the minimum value of electrical efficiency for which any power generator operates with profit. The paper demonstrates that, with regard to the profitability of cogeneration, the ratio between the cost of commodities is more important than their absolute value so that different taxation of each commodity can be a good leverage for energy policy makers to promote high efficiency cogeneration, even in the absence of an incentive mechanism. The final part of the study presents an analysis on micro-CHP technologies payback times for different European Countries. - Highlights: • Investigation of the grey area where CHP profitably operates also with negative PES. • Study starts from definition of primary energy saving PES and cost saving ratio CSR. • Definition of the R-index as the ratio between the cost of fuel and electricity. • The optimal value of R for which the “grey area” disappears is R = η_e_l_-_r_e_f. • R is also the value of η_e_l for which any electric generator profitably operates.

Emissions from decentralised CHP plants 2007 - Energinet.dk Environmental project no. 07/1882

DEFF Research Database (Denmark)

Nielsen, Malene; Nielsen, Ole-Kenneth; Thomsen, Marianne

Updated emission factors for decentralised combined heat and power (CHP) plants with a capacity project emission measurements as well as emission measurements performed in recent years that were collected. The emission factors valid for 2006/2007 have been...... estimated for the plant technologies: Municipal solid waste (MSW) incineration plants, plants combusting straw or wood, natural gas fuelled reciprocating engines, biogas fuelled engines, natural gas fuelled gas turbines, gas oil fuelled reciprocating engines, gas oil fuelled gas turbines, steam turbines...

Analyzing a self-managed CHP system for greenhouse cultivation as a profitable way to reduce CO2-emissions

International Nuclear Information System (INIS)

Compernolle, Tine; Witters, Nele; Van Passel, Steven; Thewys, Theo

2011-01-01

To counter global warming, a transition to a low-carbon economy is needed. The greenhouse sector can contribute by installing Combined Heat and Power (CHP) systems, known for their excellent energy efficiency. Due to the recent European liberalization of the energy market, glass horticulturists have the opportunity to sell excess electricity to the market and by tailored policy and support measures, regional governments can fill the lack of technical and economic knowledge, causing initial resistance. This research investigates the economic and environmental opportunities using two detailed cases applying a self managed cogeneration system. The Net Present Value is calculated to investigate the economic feasibility. The Primary Energy Saving, the CO 2 Emission Reduction indicator and an Emission Balance are applied to quantify the environmental impact. The results demonstrate that a self-managed CHP system is economic viable and that CO 2 emissions are reduced.

Clinical review of supracricoid laryngectomy with CHEP and CHP. 50 patients treated in 11 years

International Nuclear Information System (INIS)

Nakayama, Meijin; Seino, Yutomo; Hayashi, Seiichi; Miyamoto, Shunsuke; Takeda, Masahiko; Masaki, Takashi; Yokobori, Satoru; Okamoto, Makito

2009-01-01

An analysis of clinical data on 50 patients undergoing supracricoid laryngectomy (SCL) between 1997 and 2008 id est (i.e.), cricohyoidoepiglottopexy (CHEP) in 47 and cricohyoidopexy (CHP) in 3 cases showed that the number of SCL cases operated on within a year surpassed that of Total Laryngectomy after 2003. Selection criteria included performance status 0-1 and blood gas PO2>80 torr, especially in those patients over 70 years old. Postoperative wound infection occurred in 16 patients (32%), with four requiring additional surgical intervention (two ruptured pexis and two chondritis induced by C3-C4 osteophytes). A history of radiotherapy and systemic complications, i.e., diabetes and renal failure, added to the risk of wound infection. Introducing a clinical pathway shortened hospitalization. Vocal function was achieved in 96% and swallowing function in 89% of patients. Five-year crude survival in CHEP was 69% and in total laryngectomy (TL) 51%. Laryngeal preservation was 70%, increasing to 89% after the introduction of SCL. SCL-CHEP is thus indicated for unfavorable T2 (ASCO 2006), well-selected T3, T4, and rT1-4 (radiation failures). Effort should emphasize a good balance in prognosis and function in organ preservation for laryngeal cancer. (author)

DEVELOPMENT OF THE CHP-THERMAL SCHEMES IN CONTEXTS OF THE CONSOLIDATED ENERGY SYSTEM OF BELARUS

Directory of Open Access Journals (Sweden)

V. N. Romaniuk

2015-01-01

Full Text Available The paper deals with the structural specifics of the Belarus Consolidated Energy System capacities in view of their ongoing transfer to the combined-cycle technology, building the nuclear power plant and necessity for the generating capacity regulation in compliance with the load diagram. With the country’s economic complex energy utilization pattern being preserved, the generating capacities are subject to restructuring and the CHP characteristics undergo enhancement inter alia a well-known increase of the specific electricity production based on the heat consumption. Because of this the steam-turbine condensation units which are the traditional capacity regulators for the energy systems with heat power plants dominance are being pushed out of operation. In consequence of this complex of changes the issue of load diagram provision gains momentum which in evidence is relevant to the Consolidated Energy System of Belarus. One of the ways to alleviate acuteness of the problem could be the specific electric energy production cut on the CHP heat consumption with preserving the heat loads and without their handover to the heat generating capacities of direct combustion i.e. without fuel over-burning. The solution lies in integrating the absorption bromous-lithium heat pump units into the CHP thermal scheme. Through their agency low-temperature heat streams of the generator cooling, the lubrication and condensation heat-extraction of steam minimal passing to the condenser systems are utilized. As a case study the authors choose one of the CHPs in the conditions of which the corresponding employment of the said pumps leads to diminution of the fuel-equivalent specific flow-rate by 20−25 g for 1 kW⋅h production and conjoined electric energy generation capacity lowering. The latter will be handed over to other generating capacities, and the choice of them affects economic expediency of the absorption bromous-lithium heat pump-units installation

Optimization of a High Temperature PEMFC micro-CHP System by Formulation and Application of a Process Integration Methodology

DEFF Research Database (Denmark)

Arsalis, Alexandros; Nielsen, Mads Pagh; Kær, Søren Knudsen

2013-01-01

A 1 kWe micro combined heat and power (CHP) system based on high temperature proton exchange membrane fuel cell (PEMFC) technology is modeled and optimized by formulation and application of a process integration methodology. The system can provide heat and electricity for a singlefamily household...

Energetic and Exergetic Analysis of a Heat Exchanger Integrated in a Solid Biomass-Fuelled Micro-CHP System with an Ericsson Engine

Directory of Open Access Journals (Sweden)

Marie Creyx

2016-04-01

Full Text Available A specific heat exchanger has been developed to transfer heat from flue gas to the working fluid (hot air of the Ericsson engine of a solid biomass-fuelled micro combined heat and power (CHP. In this paper, the theoretical and experimental energetic analyses of this heat exchanger are compared. The experimental performances are described considering energetic and exergetic parameters, in particular the effectiveness on both hot and cold sides. A new exergetic parameter called the exergetic effectiveness is introduced, which allows a comparison between the real and the ideal heat exchanger considering the Second Law of Thermodynamics. A global analysis of exergetic fluxes in the whole micro-CHP system is presented, showing the repartition of the exergy destruction among the components.

Small-scale CHP Plant based on a 35 kWel Hermetic Four Cylinder Stirling Engine for Biomass Fuels- Development, Technology and Operating Experiences

DEFF Research Database (Denmark)

Obernberger, I.; Carlsen, Henrik; Biedermann, F.

2003-01-01

) process and the Stirling engine process. The ORC process represents an economically interesting technology for small-scale biomass-fired combined heat and power plants in a power range between 400 and 1,500 kWel. A newly developed ORC technology with a nominal electric capacity of 1,000 kW was implemented...... in the biomass CHP plant Lienz (A) in the framework of an EU demonstration project. This plant was put in operation in February 2002. Stirling engines are a promising solution for installations with nominal electric capacities between 10 and 150 kW. A biomass CHP pilot plant based on a 35 kWel-Stirling engine...

Deep Incremental Boosting

OpenAIRE

Mosca, Alan; Magoulas, George D

2017-01-01

This paper introduces Deep Incremental Boosting, a new technique derived from AdaBoost, specifically adapted to work with Deep Learning methods, that reduces the required training time and improves generalisation. We draw inspiration from Transfer of Learning approaches to reduce the start-up time to training each incremental Ensemble member. We show a set of experiments that outlines some preliminary results on some common Deep Learning datasets and discuss the potential improvements Deep In...

On excursion increments in heartbeat dynamics

International Nuclear Information System (INIS)

Guzmán-Vargas, L.; Reyes-Ramírez, I.; Hernández-Pérez, R.

2013-01-01

We study correlation properties of excursion increments of heartbeat time series from healthy subjects and heart failure patients. We construct the excursion time based on the original heartbeat time series, representing the time employed by the walker to return to the local mean value. Next, the detrended fluctuation analysis and the fractal dimension method are applied to the magnitude and sign of the increments in the time excursions between successive excursions for the mentioned groups. Our results show that for magnitude series of excursion increments both groups display long-range correlations with similar correlation exponents, indicating that large (small) increments (decrements) are more likely to be followed by large (small) increments (decrements). For sign sequences and for both groups, we find that increments are short-range anti-correlated, which is noticeable under heart failure conditions

Atmospheric response to Saharan dust deduced from ECMWF reanalysis increments

Science.gov (United States)

Kishcha, P.; Alpert, P.; Barkan, J.; Kirchner, I.; Machenhauer, B.

2003-04-01

This study focuses on the atmospheric temperature response to dust deduced from a new source of data - the European Reanalysis (ERA) increments. These increments are the systematic errors of global climate models, generated in reanalysis procedure. The model errors result not only from the lack of desert dust but also from a complex combination of many kinds of model errors. Over the Sahara desert the dust radiative effect is believed to be a predominant model defect which should significantly affect the increments. This dust effect was examined by considering correlation between the increments and remotely-sensed dust. Comparisons were made between April temporal variations of the ERA analysis increments and the variations of the Total Ozone Mapping Spectrometer aerosol index (AI) between 1979 and 1993. The distinctive structure was identified in the distribution of correlation composed of three nested areas with high positive correlation (> 0.5), low correlation, and high negative correlation (Forecast(ECMWF) suggests that the PCA (NCA) corresponds mainly to anticyclonic (cyclonic) flow, negative (positive) vorticity, and downward (upward) airflow. These facts indicate an interaction between dust-forced heating /cooling and atmospheric circulation. The April correlation results are supported by the analysis of vertical distribution of dust concentration, derived from the 24-hour dust prediction system at Tel Aviv University (website: http://earth.nasa.proj.ac.il/dust/current/). For other months the analysis is more complicated because of the essential increasing of humidity along with the northward progress of the ITCZ and the significant impact on the increments.

Legislative Bargaining and Incremental Budgeting

OpenAIRE

Dhammika Dharmapala

2002-01-01

The notion of 'incrementalism', formulated by Aaron Wildavsky in the 1960's, has been extremely influential in the public budgeting literature. In essence, it entails the claim that legislators engaged in budgetary policymaking accept past allocations, and decide only on the allocation of increments to revenue. Wildavsky explained incrementalism with reference to the cognitive limitations of lawmakers and their desire to reduce conflict. This paper uses a legislative bargaining framework to u...

Carbon Debt Payback Time for a Biomass Fired CHP Plant—A Case Study from Northern Europe

Directory of Open Access Journals (Sweden)

Kristian Madsen

2018-03-01

Full Text Available The European Union (EU has experienced a large increase in the use of biomass for energy in the last decades. In 2015, biomass used to generate electricity, heat, and to a limited extent, liquid fuels accounted for 51% of the EU’s renewable energy production. Bioenergy use is expected to grow substantially to meet energy and climate targets for 2020 and beyond. This development has resulted in analyses suggesting the increased use of biomass for energy might initially lead to increased greenhouse gas (GHG emissions to the atmosphere, a so-called carbon debt. Here, we analyze carbon debt and payback time of substituting coal with forest residues for combined heat and power generation (CHP. The analysis is, in contrast to most other studies, based on empirical data from a retrofit of a CHP plant in northern Europe. The results corroborate findings of a carbon debt, here 4.4 kg CO2eq GJ−1. The carbon debt has a payback time of one year after conversion, and furthermore, the results show that GHG emissions are reduced to 50% relative to continued coal combustion after about 12 years. The findings support the use of residue biomass for energy as an effective means for climate change mitigation.

Optimal economic dispatch of FC-CHP based heat and power micro-grids

International Nuclear Information System (INIS)

Nazari-Heris, Morteza; Abapour, Saeed; Mohammadi-Ivatloo, Behnam

2017-01-01

Highlights: • The multi objective economic/environmental heat and power MG dispatch is solved. • The heat and power MG include FC, CHP, boiler, storage system, and heat buffer tank. • Multi objective scheduling of heat and power MG is solved using ε-constraint method. • DR program is employed in the stochastic programming of heat and power MG dispatch. • The uncertainties for load demand and price signals are taken into account. - Abstract: Micro-grids (MGs) are introduced as a solution for distributed energy resource (DER) units and energy storage systems (ESSs) to participate in providing the required electricity demand of controllable and non-controllable loads. In this paper, the authors study the short-term scheduling of grid-connected industrial heat and power MG which contains a fuel cell (FC) unit, combined heat and power (CHP) generation units, power-only unit, boiler, battery storage system, and heat buffer tank. The paper is aimed to solve the multi-objective MG dispatch problem containing cost and emission minimization with the considerations of demand response program and uncertainties. A probabilistic framework based on a scenario method, which is considered for load demand and price signals, is employed to overcome the uncertainties in the optimal energy management of the MG. In order to reduce operational cost, time-of-use rates of demand response programs have been modeled, and the effects of such programs on the load profile have been discussed. To solve the multi-objective optimization problem, the ε-constraint method is used and a fuzzy satisfying approach has been employed to select the best compromise solution. Three cases are studied in this research to confirm the performance of the proposed method: islanded mode, grid-connected mode, and the impact of time of the use-demand response program on MG scheduling.

Unmanned Maritime Systems Incremental Acquisition Approach

Science.gov (United States)

2016-12-01

REPORT TYPE AND DATES COVERED MBA professional report 4. TITLE AND SUBTITLE UNMANNED MARITIME SYSTEMS INCREMENTAL ACQUISITION APPROACH 5. FUNDING...Approved for public release. Distribution is unlimited. UNMANNED MARITIME SYSTEMS INCREMENTAL ACQUISITION APPROACH Thomas Driscoll, Lieutenant...UNMANNED MARITIME SYSTEMS INCREMENTAL ACQUISITION APPROACH ABSTRACT The purpose of this MBA report is to explore and understand the issues

Atmospheric response to Saharan dust deduced from ECMWF reanalysis (ERA) temperature increments

Science.gov (United States)

Kishcha, P.; Alpert, P.; Barkan, J.; Kirchner, I.; Machenhauer, B.

2003-09-01

This study focuses on the atmospheric temperature response to dust deduced from a new source of data the European Reanalysis (ERA) increments. These increments are the systematic errors of global climate models, generated in the reanalysis procedure. The model errors result not only from the lack of desert dust but also from a complex combination of many kinds of model errors. Over the Sahara desert the lack of dust radiative effect is believed to be a predominant model defect which should significantly affect the increments. This dust effect was examined by considering correlation between the increments and remotely sensed dust. Comparisons were made between April temporal variations of the ERA analysis increments and the variations of the Total Ozone Mapping Spectrometer aerosol index (AI) between 1979 and 1993. The distinctive structure was identified in the distribution of correlation composed of three nested areas with high positive correlation (>0.5), low correlation and high negative correlation (Forecast (ECMWF) suggest that the PCA (NCA) corresponds mainly to anticyclonic (cyclonic) flow, negative (positive) vorticity and downward (upward) airflow. These findings are associated with the interaction between dust-forced heating/cooling and atmospheric circulation. This paper contributes to a better understanding of dust radiative processes missed in the model.

FEM Simulation of Incremental Shear

International Nuclear Information System (INIS)

Rosochowski, Andrzej; Olejnik, Lech

2007-01-01

A popular way of producing ultrafine grained metals on a laboratory scale is severe plastic deformation. This paper introduces a new severe plastic deformation process of incremental shear. A finite element method simulation is carried out for various tool geometries and process kinematics. It has been established that for the successful realisation of the process the inner radius of the channel as well as the feeding increment should be approximately 30% of the billet thickness. The angle at which the reciprocating die works the material can be 30 deg. . When compared to equal channel angular pressing, incremental shear shows basic similarities in the mode of material flow and a few technological advantages which make it an attractive alternative to the known severe plastic deformation processes. The most promising characteristic of incremental shear is the possibility of processing very long billets in a continuous way which makes the process more industrially relevant

Economic potentials of CHP connected to district heat systems in Germany. Implementation of the EU Efficiency Directive; Wirtschaftliche Potenziale der waermeleitungsgebundenen Siedlungs-KWK in Deutschland. Umsetzung der EU-Energieeffizienzrichtlinie

Energy Technology Data Exchange (ETDEWEB)

Eikmeier, Bernd [Fraunhofer-Institut fuer Fertigungstechnik und Angewandte Materialforschung IFAM, Bremen (Germany). Organisationseinheit Systemanalyse; Bremen Univ. (Germany)

2015-07-01

The EU Efficiency Directive (2012/27/EU) is requiring all member states to carry out an evaluation of the potential for highly efficient CHP and the efficient use of district heating and cooling by December 2015. The German Federal Ministry of Economic Affairs and Energy appointed this task to the Fraunhofer Institute for Manufacturing and Advanced Materials, division for Energy Systems Analysis (formerly Bremer Energie Institut) in conjunction with other partners. The results for the sector district- and communal heating with CHP, sub-sectors private households, trade and services industry, are presented in this article.

Researching of the possibility of using absorption heat exchangers for creating the low return temperature heat supply systems based on CHP generation

Science.gov (United States)

Yavorovsky, Y. V.; Malenkov, A. S.; Zhigulina, Y. V.; Romanov, D. O.; Kurzanov, S. Y.

2017-11-01

This paper deals with the variant of modernization of the heat point within urban heat supply network in order to create the system of heat and cold supply on its basis, providing the suppliers with heat in cold months and with heat and cold in warm months. However, in cold months in the course of heating system operation, the reverse delivery water temperature is maintained below 40 °C. The analysis of heat and power indicators of the heat and cold supply system under different operating conditions throughout the year was conducted. The possibility to use the existing heat networks for the cold supply needs was estimated. The advantages of the system over the traditional heat supply systems that use Combined Heat and Power (CHP) plant as a heat source as exemplified by heat supply system from CHP with ST-80 turbine were demonstrated.

Thermodynamic, ecological and economic aspects of the use of the gas turbine for heat supply to the stripping process in a supercritical CHP plant integrated with a carbon capture installation

International Nuclear Information System (INIS)

Bartela, Łukasz; Skorek-Osikowska, Anna; Kotowicz, Janusz

2014-01-01

Highlights: • Variants of integration of CHP plant with CCS and gas turbine unit were analyzed. • The simulations of operation of plants under changing load were realized. • Conditions of competitiveness for all solutions were identified. • Integration can be profitable if prices of allowance will reach values >60 €/MgCO 2 . - Abstract: This paper presents the results of thermodynamic and economic analyses for eight variants of a combined heat and power (CHP) plant fuelled with coal working under supercritical steam parameters and integrated with a CO 2 capture installation and a gas turbine system. The motivation behind using a gas turbine in the system was to generate steam to supply heat for the stripping process that occurs in the separation installation to regenerate the sorbent. Additional analyses were conducted for the reference case, a CHP unit in which the CO 2 separation process was not conducted, to enable an economic evaluation of the integration of a CHP unit with a CO 2 separation installation according to the variants proposed. The break-even price of electricity and avoided emission costs were used to evaluate the respective solutions. In this paper, the results of the sensitivity analysis of the economic evaluation indicators in terms of the change in the annual operation time, price of emission allowance and heat demand rate for the realization of the stripping process for all cases are presented

Ductility, strength and hardness relation after prior incremental deformation (ratcheting) of austenitic steel

International Nuclear Information System (INIS)

Kussmaul, K.; Diem, H.K.; Wachter, O.

1993-01-01

Experimental investigations into the stress/strain behavior of the niobium stabilized austenitic material with the German notation X6 CrNiNb 18 10 proved that a limited incrementally applied prior deformation will reduce the total deformation capability only by the amount of the prior deformation. It could especially be determined on the little changes in the reduction of area that the basically ductile deformation behavior will not be changed by the type of the prior loading. There is a correlation between the amount of deformation and the increase in hardness. It is possible to correlate both the changes in hardness and the material properties. In the case of low cycle fatigue tests with alternating temperature an incremental increase in total strain (ratcheting) was noted to depend on the strain range applied

THE BREAKEVEN POINT GIVEN LIMIT COST USING BIOMASS CHP PLANT

Directory of Open Access Journals (Sweden)

Paula VOICU

2015-06-01

Full Text Available Biomass is a renewable source, non-fossil, from which can be obtained fuels, which can be used in power generation systems. The main difference of fossil fuels is the availability biomass in nature and that it is in continue "reproduction". The use its enable the use of materials that could be destined destruction, as a source of energy "renewable", though result with many ecological values. In this paper we will study, applying a calculation model in view optimal sizing of the cogeneration plant based on biomass, biomass cost limit for the net present value is zero. It will consider that in cogeneration systems and in heating peak systems using biomass. After applying the mathematical model for limit value of biomass cost will determine the nominal optimal coefficient of cogeneration, for which discounted net revenue value is zero. Optimal sizing of CHP plants based on using biomass will be given by optimum coefficient of cogeneration determined following the application of the proposed mathematical model.

Computer experimental analysis of the CHP performance of a 100 kW e SOFC Field Unit by a factorial design

Science.gov (United States)

Calì, M.; Santarelli, M. G. L.; Leone, P.

Gas Turbine Technologies (GTT) and Politecnico di Torino, both located in Torino (Italy), have been involved in the design and installation of a SOFC laboratory in order to analyse the operation, in cogenerative configuration, of the CHP 100 kW e SOFC Field Unit, built by Siemens-Westinghouse Power Corporation (SWPC), which is at present (May 2005) starting its operation and which will supply electric and thermal power to the GTT factory. In order to take the better advantage from the analysis of the on-site operation, and especially to correctly design the scheduled experimental tests on the system, we developed a mathematical model and run a simulated experimental campaign, applying a rigorous statistical approach to the analysis of the results. The aim of this work is the computer experimental analysis, through a statistical methodology (2 k factorial experiments), of the CHP 100 performance. First, the mathematical model has been calibrated with the results acquired during the first CHP100 demonstration at EDB/ELSAM in Westerwoort. After, the simulated tests have been performed in the form of computer experimental session, and the measurement uncertainties have been simulated with perturbation imposed to the model independent variables. The statistical methodology used for the computer experimental analysis is the factorial design (Yates' Technique): using the ANOVA technique the effect of the main independent variables (air utilization factor U ox, fuel utilization factor U F, internal fuel and air preheating and anodic recycling flow rate) has been investigated in a rigorous manner. Analysis accounts for the effects of parameters on stack electric power, thermal recovered power, single cell voltage, cell operative temperature, consumed fuel flow and steam to carbon ratio. Each main effect and interaction effect of parameters is shown with particular attention on generated electric power and stack heat recovered.

On conditional scalar increment and joint velocity-scalar increment statistics

International Nuclear Information System (INIS)

Zhang Hengbin; Wang Danhong; Tong Chenning

2004-01-01

Conditional velocity and scalar increment statistics are usually studied in the context of Kolmogorov's refined similarity hypotheses and are considered universal (quasi-Gaussian) for inertial-range separations. In such analyses the locally averaged energy and scalar dissipation rates are used as conditioning variables. Recent studies have shown that certain local turbulence structures can be captured when the local scalar variance (φ 2 ) r and the local kinetic energy k r are used as the conditioning variables. We study the conditional increments using these conditioning variables, which also provide the local turbulence scales. Experimental data obtained in the fully developed region of an axisymmetric turbulent jet are used to compute the statistics. The conditional scalar increment probability density function (PDF) conditional on (φ 2 ) r is found to be close to Gaussian for (φ 2 ) r small compared with its mean and is sub-Gaussian and bimodal for large (φ 2 ) r , and therefore is not universal. We find that the different shapes of the conditional PDFs are related to the instantaneous degree of non-equilibrium (production larger than dissipation) of the local scalar. There is further evidence of this from the conditional PDF conditional on both (φ 2 ) r and χ r , which is largely a function of (φ 2 ) r /χ r , a measure of the degree of non-equilibrium. The velocity-scalar increment joint PDF is close to joint Gaussian and quad-modal for equilibrium and non-equilibrium local velocity and scalar, respectively. The latter shape is associated with a combination of the ramp-cliff and plane strain structures. Kolmogorov's refined similarity hypotheses also predict a dependence of the conditional PDF on the degree of non-equilibrium. Therefore, the quasi-Gaussian (joint) PDF, previously observed in the context of Kolmogorov's refined similarity hypotheses, is only one of the conditional PDF shapes of inertial range turbulence. The present study suggests that

Australian coal mine methane emissions mitigation potential using a Stirling engine-based CHP system

International Nuclear Information System (INIS)

Meybodi, Mehdi Aghaei; Behnia, Masud

2013-01-01

Methane, a major contributor to global warming, is a greenhouse gas emitted from coal mines. Abundance of coal mines and consequently a considerable amount of methane emission requires drastic measures to mitigate harmful effects of coal mining on the environment. One of the commonly adopted methods is to use emitted methane to fuel power generation systems; however, instability of fuel sources hinders the development of systems using conventional prime movers. To address this, application of Stirling engines may be considered. Here, we develop a techno-economic methodology for conducting an optimisation-based feasibility study on the application of Stirling engines as the prime movers of coal mine CHP systems from an economic and an environmental point of view. To examine the impact of environmental policies on the economics of the system, the two commonly implemented ones (i.e. a carbon tax and emissions trading scheme) are considered. The methodology was applied to a local coal mine. The results indicate that incorporating the modelled system not only leads to a substantial reduction in greenhouse gas emissions, but also to improved economics. Further, due to the heavy economic burden, the carbon tax scheme creates great incentive for coal mine industry to address the methane emissions. -- Highlights: •We study the application of Stirling engines in coal mine CHP systems. •We develop a thermo-economic approach based on the net present worth analysis. •We examine the impact of a carbon tax and ETS on the economics of the system. •The modeled system leads to a substantial reduction in greenhouse gas emissions. •Carbon tax provides a greater incentive to address the methane emissions

[Spatiotemporal variation of Populus euphratica's radial increment at lower reaches of Tarim River after ecological water transfer].

Science.gov (United States)

An, Hong-Yan; Xu, Hai-Liang; Ye, Mao; Yu, Pu-Ji; Gong, Jun-Jun

2011-01-01

Taking the Populus euphratica at lower reaches of Tarim River as test object, and by the methods of tree dendrohydrology, this paper studied the spatiotemporal variation of P. euphratic' s branch radial increment after ecological water transfer. There was a significant difference in the mean radial increment before and after ecological water transfer. The radial increment after the eco-water transfer was increased by 125%, compared with that before the water transfer. During the period of ecological water transfer, the radial increment was increased with increasing water transfer quantity, and there was a positive correlation between the annual radial increment and the total water transfer quantity (R2 = 0.394), suggesting that the radial increment of P. euphratica could be taken as the performance indicator of ecological water transfer. After the ecological water transfer, the radial increment changed greatly with the distance to the River, i.e. , decreased significantly along with the increasing distance to the River (P = 0.007). The P. euphratic' s branch radial increment also differed with stream segment (P = 0.017 ), i.e. , the closer to the head-water point (Daxihaizi Reservoir), the greater the branch radial increment. It was considered that the limited effect of the current ecological water transfer could scarcely change the continually deteriorating situation of the lower reaches of Tarim River.

[Incremental cost effectiveness of multifocal cataract surgery].

Science.gov (United States)

Pagel, N; Dick, H B; Krummenauer, F

2007-02-01

Supplementation of cataract patients with multifocal intraocular lenses involves an additional financial investment when compared to the corresponding monofocal supplementation, which usually is not funded by German health care insurers. In the context of recent resource allocation discussions, however, the cost effectiveness of multifocal cataract surgery could become an important rationale. Therefore an evidence-based estimation of its cost effectiveness was carried out. Three independent meta-analyses were implemented to estimate the gain in uncorrected near visual acuity and best corrected visual acuity (vision lines) as well as the predictability (fraction of patients without need for reading aids) of multifocal supplementation. Study reports published between 1995 and 2004 (English or German language) were screened for appropriate key words. Meta effects in visual gain and predictability were estimated by means and standard deviations of the reported effect measures. Cost data were estimated by German DRG rates and individual lens costs; the cost effectiveness of multifocal cataract surgery was then computed in terms of its marginal cost effectiveness ratio (MCER) for each clinical benefit endpoint; the incremental costs of multifocal versus monofocal cataract surgery were further estimated by means of their respective incremental cost effectiveness ratio (ICER). An independent meta-analysis estimated the complication profiles to be expected after monofocal and multifocal cataract surgery in order to evaluate expectable complication-associated additional costs of both procedures; the marginal and incremental cost effectiveness estimates were adjusted accordingly. A sensitivity analysis comprised cost variations of +/- 10 % and utility variations alongside the meta effect estimate's 95 % confidence intervals. Total direct costs from the health care insurer's perspective were estimated 3363 euro, associated with a visual meta benefit in best corrected visual

Experience of Implementing a Distributed Control System for Thermal and Mechanical and Electrical Equipment at the South-West CHP

Energy Technology Data Exchange (ETDEWEB)

Babkin, K. V., E-mail: babkin@uztec.ru; Tsvetkov, M. S.; Kostyuk, R. I.; Chugin, A. V. [SC “South-West CHP” (Russian Federation); Bilenko, V. A.; Molchanov, K. A.; Fedunov, V. V. [JSC “Interautomatika” (Russian Federation)

2015-01-15

Results of implementing an SPPA-T3000-based unified distributed control system for thermal and mechanical and electrical equipment at the South-West CHP are discussed. Hardware solutions for integration with local control systems, control of electrical equipment in compliance with the standards IEC 61850, Modbus RTU, and communication between the plant control system and the System Operator of the Unified Power System are described.

Experience of Implementing a Distributed Control System for Thermal and Mechanical and Electrical Equipment at the South-West CHP

International Nuclear Information System (INIS)

Babkin, K. V.; Tsvetkov, M. S.; Kostyuk, R. I.; Chugin, A. V.; Bilenko, V. A.; Molchanov, K. A.; Fedunov, V. V.

2015-01-01

Results of implementing an SPPA-T3000-based unified distributed control system for thermal and mechanical and electrical equipment at the South-West CHP are discussed. Hardware solutions for integration with local control systems, control of electrical equipment in compliance with the standards IEC 61850, Modbus RTU, and communication between the plant control system and the System Operator of the Unified Power System are described

Adults with initial metabolic syndrome have altered muscle deoxygenation during incremental exercise.

Science.gov (United States)

Machado, Alessandro da Costa; Barbosa, Thales Coelho; Kluser Sales, Allan Robson; de Souza, Marcio Nogueira; da Nóbrega, Antonio Claudio Lucas; Silva, Bruno Moreira

2017-02-01

Reduced aerobic power is independently associated with metabolic syndrome (MetS) incidence and prevalence in adults. This study investigated whether muscle deoxygenation (proxy of microvascular O 2 extraction) during incremental exercise is altered in MetS and associated with reduced oxygen consumption ( V˙O 2peak ). Twelve men with initial MetS (no overt diseases and medication-naive; mean ± SD, age 38 ± 7 years) and 12 healthy controls (HCs) (34 ± 7 years) completed an incremental cycling test to exhaustion, in which pulmonary ventilation and gas exchange (metabolic analyzer), as well as vastus lateralis deoxygenation (near infrared spectroscopy), were measured. Subjects with MetS, in contrast to HCs, showed lower V˙O 2peak normalized to total lean mass, similar V˙O 2 response to exercise, and earlier break point (BP) in muscle deoxygenation. Consequently, deoxygenation slope from BP to peak exercise was greater. Furthermore, absolute V˙O 2peak was positively associated with BP in correlations adjusted for total lean mass. MetS, without overt diseases, altered kinetics of muscle deoxygenation during incremental exercise, particularly at high-intensity exercise. Therefore, the balance between utilization and delivery of O 2 within skeletal muscle is impaired early in MetS natural history, which may contribute to the reduction in aerobic power. © 2017 The Obesity Society.

Five-year outcomes for frontline brentuximab vedotin with CHP for CD30-expressing peripheral T-cell lymphomas.

Science.gov (United States)

Fanale, Michelle A; Horwitz, Steven M; Forero-Torres, Andres; Bartlett, Nancy L; Advani, Ranjana H; Pro, Barbara; Chen, Robert W; Davies, Andrew; Illidge, Tim; Uttarwar, Mayur; Lee, Shih-Yuan; Ren, Hong; Kennedy, Dana A; Shustov, Andrei R

2018-05-10

This phase 1 study evaluated frontline brentuximab vedotin in combination with cyclophosphamide, doxorubicin, and prednisone (BV+CHP; 6 cycles, then up to 10 cycles of brentuximab vedotin monotherapy) in 26 patients with CD30 + peripheral T-cell lymphoma, including 19 with systemic anaplastic large cell lymphoma. All patients (100%) achieved an objective response, with a complete remission (CR) rate of 92%; none received a consolidative stem cell transplant. After a median observation period of 59.6 months (range, 4.6-66.0) from first dose, neither the median progression-free survival (PFS) nor the median overall survival (OS) was reached. No progression or death was observed beyond 35 months. The estimated 5-year PFS and OS rates were 52% and 80%, respectively. Eighteen of 19 patients (95%) with treatment-emergent peripheral neuropathy (PN) reported resolution or improvement of symptoms. Thirteen patients (50%) remained in remission at the end of the study, with PFS ranging from 37.8+ to 66.0+ months. Eight of these 13 patients received the maximum 16 cycles of study treatment. These final results demonstrate durable remissions in 50% of patients treated with frontline BV+CHP, suggesting a potentially curative treatment option for some patients. This trial was registered at www.clinicaltrials.gov as #NCT01309789. © 2018 by The American Society of Hematology.

Investigation of Continuous Gas Engine CHP Operation on Biomass Producer Gas

DEFF Research Database (Denmark)

Ahrenfeldt, Jesper; Henriksen, Ulrik Birk; Jensen, Torben Kvist

2005-01-01

More than 2000 hours of gas engine operation with producer gas from biomass as fuel has been conducted on the gasification CHP demonstration and research plant, named “Viking” at the Technical University of Denmark. The gas engine is an integrated part of the entire gasification plant. The excess...... operates with varying excess of air due to variation in gas composition and thus stoichiometry, and a second where the excess of air in the exhaust gas is fixed and the flow rate of produced gas from the gasifier is varying. The interaction between the gas engine and the gasification system has been...... investigated. The engine and the plant are equipped with continuously data acquisition that monitors the operation including the composition of the producer gas and the flow. Producer gas properties and contaminations have been investigated. No detectable tar or particle content was observed...

48 CFR 3432.771 - Provision for incremental funding.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Provision for incremental funding. 3432.771 Section 3432.771 Federal Acquisition Regulations System DEPARTMENT OF EDUCATION..., Incremental Funding, in a solicitation if a cost-reimbursement contract using incremental funding is...

Diagnostic value of triphasic incremental helical CT in early and progressive gastric carcinoma

International Nuclear Information System (INIS)

Gao Jianbo; Yan Xuehua; Li Mengtai; Guo Hua; Chen Xuejun; Guan Sheng; Zhang Xiefu; Li Shuxin; Yang Xiaopeng

2001-01-01

Objective: To investigate helical CT enhancement characteristics of gastric carcinoma, and the diagnostic value and preoperative staging of gastric carcinoma with triphasic incremental helical CT of the stomach with water-filling method. Methods: Both double-contrast barium examination and triphasic incremental helical CT of the stomach with water-filling method were performed in 46 patients with gastric carcinoma. Results: (1) Among these patients, normal gastric wall exhibited one layered structure in 18 patients, two or three layered structure in 28 patients in the arterial and portal venous phase. (2) Two cases of early stomach cancer showed marked enhancement in the arterial and portal venous phase and obvious attenuation of enhancement in the equilibrium phase. On the contrary, 32 of the 44 advanced gastric carcinoma was showed marked enhancement in the venous phase compared with the arterial phase ( t = 4.226, P < 0.05). (3) The total accuracy of triphasic incremental helical CT in determining TNM-staging was 81.0%. Conclusion: Different types of gastric carcinoma have different enhancement features. Triphases incremental helical CT is more accurate than conventional CT in the preoperative staging of gastric carcinoma

Heading towards the nZEB through CHP+HP systems. A comparison between retrofit solutions able to increase the energy performance for the heating and domestic hot water production in residential buildings

International Nuclear Information System (INIS)

Salata, Ferdinando; Golasi, Iacopo; Domestico, Umberto; Banditelli, Matteo; Lo Basso, Gianluigi; Nastasi, Benedetto; Lieto Vollaro, Andrea de

2017-01-01

Highlights: • Energy optimization measures to increase the energy class of buildings. • Analysis of the demands related to the space-heating season and the production of annual DHW. • Case study related to a residential building of medium size located in Rome (Italy). • Improvements on building envelope and on systems (traditional technologies or CHP+HP). • Energy and economic analysis to achieve the performance of a nZEB. - Abstract: Optimizing consumptions in the field of civil construction led to define energy labels for residential buildings. To calculate the building energy demand the EPgl was determined, i.e. the annual consumption per m"2 of primary energy. This paper examines the technical solutions useful to optimize the energy demands for heating during space-heating season and domestic hot water production (thanks to energy analysis softwares as MC11300 and TRNSYS) and, at the same time, to take into account the financial issues those interventions implied. The total inside heated surface of the building case study is 1204.00 m"2, hence the inside heated volume is about 3250.80 m"3. Besides the more traditional interventions concerning the building envelope and its systems, the paper examined the performance of a system obtained through the combination of a cogenerator (CHP) and a heat pump (HP), thus, substituting the conventional boilers of the buildings. CHP+HP solution increases the most the energy label of the building (from a D class with EPgl = 59.62 kW h m"−"2 year"−"1, to an A class, with EPgl = 25.64 kW h m"−"2 year"−"1), determining an annual energy cost saving of 3,114 € year"−"1, allowing to amortize installation costs (54,560 €) in a reasonable payback period, i.e. 15.4 years. This innovative solution in the residential sector can be realized through retrofit interventions on existing buildings, hence it leads the current dwelling towards nZEB with a remarkable benefits for the environment.

Increment memory module for spectrometric data recording

International Nuclear Information System (INIS)

Zhuchkov, A.A.; Myagkikh, A.I.

1988-01-01

Incremental memory unit designed to input differential energy spectra of nuclear radiation is described. ROM application as incremental device has allowed to reduce the number of elements and do simplify information readout from the unit. 12-bit 2048 channels present memory unit organization. The device is connected directly with the bus of microprocessor systems similar to KR 580. Incrementation maximal time constitutes 3 mks. It is possible to use this unit in multichannel counting mode

Small Diameter Bomb Increment II (SDB II)

Science.gov (United States)

2015-12-01

Selected Acquisition Report (SAR) RCS: DD-A&T(Q&A)823-439 Small Diameter Bomb Increment II (SDB II) As of FY 2017 President’s Budget Defense... Bomb Increment II (SDB II) DoD Component Air Force Joint Participants Department of the Navy Responsible Office References SAR Baseline (Production...Mission and Description Small Diameter Bomb Increment II (SDB II) is a joint interest United States Air Force (USAF) and Department of the Navy

Hydrocarbon emissions from gas engine CHP-units. 2011 measurement program

Energy Technology Data Exchange (ETDEWEB)

Van Dijk, G.H.J. [KEMA, Arnhem (Netherlands)

2012-06-15

In December 2009, the Ministry of Infrastructure and Environment (IandM) issued the Decree on Emission Limits for Middle Sized Combustion Installations (BEMS). This decree imposes a first-time emission limit value (ELV) of 1500 mg C/m{sup 3}{sub o} at 3% O{sub 2} for hydrocarbons emitted by gas engines. IandM used the findings of two hydrocarbon emission measurement programs, executed in 2007 and 2009, as a guideline for this initial ELV. The programs did reveal substantial variation in the hydrocarbon emissions of the gas engines tested. This variation, and especially the uncertainty as to the role of engine and/or other parameters causing such variation, was felt to hamper further policy development. IandM therefore commissioned KEMA to perform follow-up measurements on ten gas engine CHP-units in 2011. Aim of this 2011 program is to assess hydrocarbon emission variation in relation to engine parameters and process conditions including maintenance status, and to atmospheric conditions. The 2011 program comprised two identical measurement sessions, one in spring and one in winter.

Planning Through Incrementalism

Science.gov (United States)

Lasserre, Ph.

1974-01-01

An incremental model of decisionmaking is discussed and compared with the Comprehensive Rational Approach. A model of reconciliation between the two approaches is proposed, and examples are given in the field of economic development and educational planning. (Author/DN)

Reducing the network load and optimization of the economic efficiency of CHP plants by forecast-guided control; Verringerung der Netzbelastung und Optimierung der Wirtschaftlichkeit von KWK-Anlagen durch prognosegefuehrte Steuerung

Energy Technology Data Exchange (ETDEWEB)

Glaser, Daniel; Adelhardt, Stefan [Erlangen-Nuernberg Univ., Erlangen (Germany). Lehrstuhl fuer Sensorik; beECO GmbH, Erlangen (Germany)

2012-07-01

Heat-guided combined heat and power (CHP) plants often cause large compensation energy amounts, additional costs to the operator respectively and another burden on the parent network. The balance energy is caused by errors in the production forecast whose quality heavily depends on the heat load performance. This paper identifies the forecasting problems with heat-guided CHP and reveals how the accompanying cost and the network burden can be reduced. This is achieved by an improvement of the forecast in conjunction with a forecast-guided control without affecting the heat supply. In addition, an outlook on further measures to the earnings with the system is presented. (orig.)

FDTD Stability: Critical Time Increment

OpenAIRE

Z. Skvor; L. Pauk

2003-01-01

A new approach suitable for determination of the maximal stable time increment for the Finite-Difference Time-Domain (FDTD) algorithm in common curvilinear coordinates, for general mesh shapes and certain types of boundaries is presented. The maximal time increment corresponds to a characteristic value of a Helmholz equation that is solved by a finite-difference (FD) method. If this method uses exactly the same discretization as the given FDTD method (same mesh, boundary conditions, order of ...

Sizing a solar dish Stirling micro-CHP system for residential application in diverse climatic conditions based on 3E analysis

International Nuclear Information System (INIS)

Moghadam, Ramin Shabanpour; Sayyaadi, Hoseyn; Hosseinzade, Hadi

2013-01-01

Highlights: • 3E analysis was performed on solar CHP systems. • Significant primary energy saving and greenhouse gas reduction were obtained. • The engine was sized so that it had the best economic sound. • Various criteria at different weathers were used for sizing the engine. - Abstract: A solar dish Stirling cogeneration system is considered to provide energy demands of a residential building. As energy demands of the building and output power of the engine are functions of weather condition and solar irradiation flux, the benchmark building was considered to be located in five different cities in Iran with diverse climatic and solar irradiation conditions. The proposed solar dish Stirling micro-CHP system was analyzed based on 3E analysis. The 3E analysis evaluated primary energy saving analysis (energy analysis), carbon dioxide emission reduction (environmental analysis) and payback period for return of investment (economic analysis) and was compared to a reference building that utilized primary energy carriers for its demands. Three scenarios were considered for assessment and sizing the solar dish Stirling engine. In the first scenario, size of the solar dish Stirling engine was selected based on the lowest annual electric power demand while, in second, the highest annual electric power consumption was considered to specify size of the engine. In the third scenario, a solar dish Stirling engine with constant output capacity was considered for the five locations. It was shown that implementing the solar dish Stirling micro-CHP system had good potential in primary energy saving and carbon dioxide emission reduction in all scenarios and acceptable payback period for return of the investment in some scenarios. Finally, the best scenario for selecting size of the engine in each city was introduced using the TOPSIS decision making method. It was demonstrated that, for dry weather, the first scenario was the best while, for hot and humid cities and

Incremental health care utilization and costs for acute otitis media in children.

Science.gov (United States)

Ahmed, Sameer; Shapiro, Nina L; Bhattacharyya, Neil

2014-01-01

Determine the incremental health care costs associated with the diagnosis and treatment of acute otitis media (AOM) in children. Cross-sectional analysis of a national health-care cost database. Pediatric patients (age children with and without a diagnosis of AOM, adjusting for age, sex, region, race, ethnicity, insurance coverage, and Charlson comorbidity Index. A total of 8.7 ± 0.4 million children were diagnosed with AOM (10.7 ± 0.4% annually, mean age 5.3 years, 51.3% male) among 81.5 ± 2.3 million children sampled (mean age 8.9 years, 51.3% male). Children with AOM manifested an additional +2.0 office visits, +0.2 emergency department visits, and +1.6 prescription fills (all P <0.001) per year versus those without AOM, adjusting for demographics and medical comorbidities. Similarly, AOM was associated with an incremental increase in outpatient health care costs of $314 per child annually (P <0.001) and an increase of $17 in patient medication costs (P <0.001), but was not associated with an increase in total prescription expenses ($13, P = 0.766). The diagnosis of AOM confers a significant incremental health-care utilization burden on both patients and the health care system. With its high prevalence across the United States, pediatric AOM accounts for approximately $2.88 billion in added health care expense annually and is a significant health-care utilization concern. © 2013 The American Laryngological, Rhinological and Otological Society, Inc.

Incremental Visualizer for Visible Objects

DEFF Research Database (Denmark)

Bukauskas, Linas; Bøhlen, Michael Hanspeter

This paper discusses the integration of database back-end and visualizer front-end into a one tightly coupled system. The main aim which we achieve is to reduce the data pipeline from database to visualization by using incremental data extraction of visible objects in a fly-through scenarios. We...... also argue that passing only relevant data from the database will substantially reduce the overall load of the visualization system. We propose the system Incremental Visualizer for Visible Objects (IVVO) which considers visible objects and enables incremental visualization along the observer movement...... path. IVVO is the novel solution which allows data to be visualized and loaded on the fly from the database and which regards visibilities of objects. We run a set of experiments to convince that IVVO is feasible in terms of I/O operations and CPU load. We consider the example of data which uses...

CHP biomass gasifier for the Zwarts Gerbera Nursery. Technical and economic feasibility; Biomassavergasser-WKK voor Gerberakwekerij Zwarts. Technische inpassing en economische haalbaarheid

Energy Technology Data Exchange (ETDEWEB)

Peeters, S.; Hart, A. [Energy Matters, Driebergen (Netherlands)

2011-10-15

when we factor in the renewable energy subsidy (SDE+) and investment subsidies such as MEI and EIA. Assuming the cheaper 800 kWe installations, the SDE+ subsidy of euro 90/MWh, current wood chipping prices and co-burning of cheaper residual waste such as reed, the payback time is 3 to 4 years. If the biomass can be contracted for 4 to 5 years at a fixed price, then an investment in a CHP gasifier is definitely an interesting alternative to the current gas CHP installations within the horticulture sector. This feasibility study assumes that the horticulturer's biomass costs are euro 35/tonne for a wood and reed mixture (87.5% and 12.5% respectively) and euro 40/tonne for 100% wood chippings, including transport. This assumes euro 25/tonne reed removal costs for the supplier, the province of Utrecht, Natuurmonumenten and/or the Forestry Commission (Staatsbosbeheer). In this case these parties do not pay euro 35/tonne for the processing of the waste by a green waste collector. The horticulturer receives euro 10/tonne for buying the reed, which offsets part of his investment risk. The cheap reed thus makes a significant contribution to the profitability of the installation. However, there is insufficient reed in the province of Utrecht to meet the total energy requirement of the Zwarts nursery, let alone for more energy projects. Moreover, the placement of the installation is subject to an Area Exploitation (WABO) Permit and the implementation of several measures. The installation is feasible in the current situation, both in terms of placement, technical compatibility and logistics, the supply of biomass and the removal of combustion ash [Dutch] Dit rapport beschrijft de haalbaarheid van een vergasser-WKK-installatie bij Gerberakwekerij Zwarts. Met behulp van de inzichten van dit onderzoek is een beeld geschetst voor energieproductie middels vergassing in de tuinbouwsector. Let wel, elk gewas kent zijn specifieke groeibehoeften, nutriënten, warmte/koude, licht, maar

Power variation for Gaussian processes with stationary increments

DEFF Research Database (Denmark)

Barndorff-Nielsen, Ole Eiler; Corcuera, J.M.; Podolskij, Mark

2009-01-01

We develop the asymptotic theory for the realised power variation of the processes X=•G, where G is a Gaussian process with stationary increments. More specifically, under some mild assumptions on the variance function of the increments of G and certain regularity conditions on the path of the pr......We develop the asymptotic theory for the realised power variation of the processes X=•G, where G is a Gaussian process with stationary increments. More specifically, under some mild assumptions on the variance function of the increments of G and certain regularity conditions on the path...... a chaos representation....

Incremental passivity and output regulation for switched nonlinear systems

Science.gov (United States)

Pang, Hongbo; Zhao, Jun

2017-10-01

This paper studies incremental passivity and global output regulation for switched nonlinear systems, whose subsystems are not required to be incrementally passive. A concept of incremental passivity for switched systems is put forward. First, a switched system is rendered incrementally passive by the design of a state-dependent switching law. Second, the feedback incremental passification is achieved by the design of a state-dependent switching law and a set of state feedback controllers. Finally, we show that once the incremental passivity for switched nonlinear systems is assured, the output regulation problem is solved by the design of global nonlinear regulator controllers comprising two components: the steady-state control and the linear output feedback stabilising controllers, even though the problem for none of subsystems is solvable. Two examples are presented to illustrate the effectiveness of the proposed approach.

The effectiveness of heat pumps as part of CCGT-190/220 Tyumen CHP-1

Directory of Open Access Journals (Sweden)

Tretyakova Polina

2017-01-01

Full Text Available The article considers the possibility of increasing the energy efficiency of CCGT-190/220 Tyumen CHP-1 due to the utilization of low-grade heat given off in the condenser unit of the steam turbine. To assess the effectiveness of the proposed system, the indexes of thermal efficiency are given. As a result of a research the following conclusions are received: The heat-transfer agent heat pump, when heated uses low-grade heat TPP and increases heat output, but consumes the electricity. Using a heat pump is effective for a small temperature difference between the condenser and the evaporator. Good example is heating water before chemical treatment. This method is more efficient than using a replacement boiler and it is used in steam selection.

Theory of Single Point Incremental Forming

DEFF Research Database (Denmark)

Martins, P.A.F.; Bay, Niels; Skjødt, Martin

2008-01-01

This paper presents a closed-form theoretical analysis modelling the fundamentals of single point incremental forming and explaining the experimental and numerical results available in the literature for the past couple of years. The model is based on membrane analysis with bi-directional in-plan......-plane contact friction and is focused on the extreme modes of deformation that are likely to be found in single point incremental forming processes. The overall investigation is supported by experimental work performed by the authors and data retrieved from the literature.......This paper presents a closed-form theoretical analysis modelling the fundamentals of single point incremental forming and explaining the experimental and numerical results available in the literature for the past couple of years. The model is based on membrane analysis with bi-directional in...

Efficiency of Oral Incremental Rehearsal versus Written Incremental Rehearsal on Students' Rate, Retention, and Generalization of Spelling Words

Science.gov (United States)

Garcia, Dru; Joseph, Laurice M.; Alber-Morgan, Sheila; Konrad, Moira

2014-01-01

The purpose of this study was to examine the efficiency of an incremental rehearsal oral versus an incremental rehearsal written procedure on a sample of primary grade children's weekly spelling performance. Participants included five second and one first grader who were in need of help with their spelling according to their teachers. An…

Integration of torrefaction in CHP plants – A case study

International Nuclear Information System (INIS)

Starfelt, Fredrik; Tomas Aparicio, Elena; Li, Hailong; Dotzauer, Erik

2015-01-01

Highlights: • We model the integration of a torrefaction reactor in a CHP plant. • Techno-economic analysis for the system is performed. • Flue gas integration of torrefaction show better performance. • Heat or electricity production is not compromised in the proposed system. - Abstract: Torrefied biomass shows characteristics that resemble those of coal. Therefore, torrefied biomass can be co-combusted with coal in existing coal mills and burners. This paper presents simulation results of a case study where a torrefaction reactor was integrated in an existing combined heat and power plant and sized to replace 25%, 50%, 75% or 100% of the fossil coal in one of the boilers. The simulations show that a torrefaction reactor can be integrated with existing plants without compromising heat or electricity production. Economic and sensitivity analysis show that the additional cost for integrating a torrefaction reactor is low which means that with an emission allowance cost of 37 €/ton CO 2 , the proposed integrated system can be profitable and use 100% renewable fuels. The development of subsidies will affect the process economy. The determinant parameters are electricity and fuel prices

Implications of the modelling of stratified hot water storage tanks in the simulation of CHP plants

Energy Technology Data Exchange (ETDEWEB)

Campos Celador, A., E-mail: alvaro.campos@ehu.es [ENEDI Research Group-University of the Basque Country, Departamento de Maquinas y Motores Termicos, E.T.S.I. de Bilbao Alameda de Urquijo, s/n 48013 Bilbao, Bizkaia (Spain); Odriozola, M.; Sala, J.M. [ENEDI Research Group-University of the Basque Country, Departamento de Maquinas y Motores Termicos, E.T.S.I. de Bilbao Alameda de Urquijo, s/n 48013 Bilbao, Bizkaia (Spain)

2011-08-15

Highlights: {yields} Three different modelling approaches for simulation of hot water tanks are presented. {yields} The three models are simulated within a residential cogeneration plant. {yields} Small differences in the results are found by an energy and exergy analysis. {yields} Big differences between the results are found by an advanced exergy analysis. {yields} Results on the feasibility study are explained by the advanced exergy analysis. - Abstract: This paper considers the effect that different hot water storage tank modelling approaches have on the global simulation of residential CHP plants as well as their impact on their economic feasibility. While a simplified assessment of the heat storage is usually considered in the feasibility studies of CHP plants in buildings, this paper deals with three different levels of modelling of the hot water tank: actual stratified model, ideal stratified model and fully mixed model. These three approaches are presented and comparatively evaluated under the same case of study, a cogeneration plant with thermal storage meeting the loads of an urbanisation located in the Bilbao metropolitan area (Spain). The case of study is simulated by TRNSYS for each one of the three modelling cases and the so obtained annual results are analysed from both a First and Second-Law-based viewpoint. While the global energy and exergy efficiencies of the plant for the three modelling cases agree quite well, important differences are found between the economic results of the feasibility study. These results can be predicted by means of an advanced exergy analysis of the storage tank considering the endogenous and exogenous exergy destruction terms caused by the hot water storage tank.

Are high penetrations of commercial cogeneration good for society?

Science.gov (United States)

Keen, Jeremy F.; Apt, Jay

2016-12-01

Low natural gas prices, market reports and evidence from New York State suggest that the number of commercial combined heat and power (CHP) installations in the United States will increase by 2%-9% annually over the next decade. We investigate how increasing commercial CHP penetrations may affect net emissions, the distribution network, and total system energy costs. We constructed an integrated planning and operations model that maximizes owner profit through sizing and operation of CHP on a realistic distribution feeder in New York. We find that a greater penetration of CHP reduces both total system energy costs and network congestion. Commercial buildings often have low and inconsistent heat loads, which can cause low fuel utilization efficiencies, low CHP rates-of-return and diminishing avoided emissions as CHP penetration increases. In the northeast, without policy intervention, a 5% penetration of small commercially owned CHP would increase CO2 emissions by 2% relative to the bulk power grid. Low emission CHP installations can be encouraged with incentives that promote CHP operation only during times of high heat loads. Time-varying rates, such as time-of-day and seasonal rates, are one option and were shown to reduce customer emissions without reducing profits. In contrast, natural gas rate discounts, a common incentive for industrial CHP in some states, can encourage CHP operation during low heat loads and thus increase emissions.

Performance Evaluation of Incremental K-means Clustering Algorithm

OpenAIRE

Chakraborty, Sanjay; Nagwani, N. K.

2014-01-01

The incremental K-means clustering algorithm has already been proposed and analysed in paper [Chakraborty and Nagwani, 2011]. It is a very innovative approach which is applicable in periodically incremental environment and dealing with a bulk of updates. In this paper the performance evaluation is done for this incremental K-means clustering algorithm using air pollution database. This paper also describes the comparison on the performance evaluations between existing K-means clustering and i...

Process Intensification in Fuel Cell CHP Systems, the ReforCELL Project

Directory of Open Access Journals (Sweden)

José Luis Viviente

2016-10-01

Full Text Available This paper reports the findings of a FP7/FCH JU project (ReforCELL that developed materials (catalysts and membranes and an advance autothermal membrane reformer for a micro Combined Heat and Power (CHP system of 5 kWel based on a polymer electrolyte membrane fuel cell (PEMFC. In this project, an active, stable and selective catalyst was developed for the reactions of interest and its production was scaled up to kg scale (TRL5 (TRL: Technology Readiness Level. Simultaneously, new membranes for gas separation were developed. In particular, dense supported thin palladium-based membranes were developed for hydrogen separation from reactive mixtures. These membranes were successfully scaled up to TRL4 and used in lab-scale reactors for fluidized bed steam methane reforming (SMR and autothermal reforming (ATR and in a prototype reactor for ATR. Suitable sealing techniques able to integrate the different membranes in lab-scale and prototype reactors were also developed. The project also addressed the design and optimization of the subcomponents (BoP for the integration of the membrane reformer to the fuel cell system.

Quantum independent increment processes

CERN Document Server

Franz, Uwe

2005-01-01

This volume is the first of two volumes containing the revised and completed notes lectures given at the school "Quantum Independent Increment Processes: Structure and Applications to Physics". This school was held at the Alfried-Krupp-Wissenschaftskolleg in Greifswald during the period March 9 – 22, 2003, and supported by the Volkswagen Foundation. The school gave an introduction to current research on quantum independent increment processes aimed at graduate students and non-specialists working in classical and quantum probability, operator algebras, and mathematical physics. The present first volume contains the following lectures: "Lévy Processes in Euclidean Spaces and Groups" by David Applebaum, "Locally Compact Quantum Groups" by Johan Kustermans, "Quantum Stochastic Analysis" by J. Martin Lindsay, and "Dilations, Cocycles and Product Systems" by B.V. Rajarama Bhat.

Integrated energy markets and varying degrees of liberalisation: price links, bundled sales and CHP production exemplified by Northern European experiences

International Nuclear Information System (INIS)

Jacobsen, H.K.; Fristrup, P.; Munksgaard, J.

2006-01-01

Liberalisation of energy markets has during the last 20 years been gradually introduced in many countries. The liberalisation has led to concerns regarding the markets' state of competition and fears that market power existence can result in less efficiency gains than what is expected from liberalisation. Concerns have also been raised as to whether specific consumer groups will be affected by limited competition in markets. Much of the concern has been concentrated on the electricity markets, but the development of energy sectors with integration of activities within natural gas, electricity and the oil sector creates the need to examine market power aspects across these markets. This paper examines the concentration trends in the Northern European markets for electricity and natural gas, combined with regional district heating aspects, especially with respect to the situation in Denmark. The situation with natural gas companies supplying to both small-scale CHP and to retail heat customers is discussed, for instance, which changes of regulatory regime for domestic heating customers should be considered when the natural gas market is being liberalised? The interlinked nature of the energy markets is described and examples of impacts from one market with limited competition to other markets with seemingly well-functioning competition are given. The specific case of large CHP production facilities with output on the regulated district heating market and the competitive Nordic electricity market is examined. How much of the fluctuations in price experienced in electricity markets should be reflected in the price of heating supplies? To which degree do the heating customers have to bear the burden of low-electricity market prices? Regulation of liberalised markets is discussed focusing on the interaction between one regulated market and the related energy markets that are liberalised. Existing regulation on the markets are compared to a situation where liberalisation

Integrated energy markets and varying degrees of liberalisation: Price links, bundled sales and CHP production exemplified by Northern European experiences

International Nuclear Information System (INIS)

Klinge Jacobsen, Henrik; Fristrup, Peter; Munksgaard, Jesper

2006-01-01

Liberalisation of energy markets has during the last 20 years been gradually introduced in many countries. The liberalisation has led to concerns regarding the markets' state of competition and fears that market power existence can result in less efficiency gains than what is expected from liberalisation. Concerns have also been raised as to whether specific consumer groups will be affected by limited competition in markets. Much of the concern has been concentrated on the electricity markets, but the development of energy sectors with integration of activities within natural gas, electricity and the oil sector creates the need to examine market power aspects across these markets. This paper examines the concentration trends in the Northern European markets for electricity and natural gas, combined with regional district heating aspects, especially with respect to the situation in Denmark. The situation with natural gas companies supplying to both small-scale CHP and to retail heat customers is discussed, for instance, which changes of regulatory regime for domestic heating customers should be considered when the natural gas market is being liberalised? The interlinked nature of the energy markets is described and examples of impacts from one market with limited competition to other markets with seemingly well-functioning competition are given. The specific case of large CHP production facilities with output on the regulated district heating market and the competitive Nordic electricity market is examined. How much of the fluctuations in price experienced in electricity markets should be reflected in the price of heating supplies? To which degree do the heating customers have to bear the burden of low-electricity market prices? Regulation of liberalised markets is discussed focusing on the interaction between one regulated market and the related energy markets that are liberalised. Existing regulation on the markets are compared to a situation where liberalisation

Fuel cell power plants for decentralised CHP applications; Brennstoffzellen-Kraftwerke fuer dezentrale KWK-Anwendungen

Energy Technology Data Exchange (ETDEWEB)

Ohmer, Martin; Mattner, Katja [FuelCell Energy Solutions GmbH, Dresden (Germany)

2015-06-01

Fuel cells are the most efficient technology to convert chemical energy into electricity and heat and thus they could have a major impact on reducing fuel consumption, CO{sub 2} and other emissions (NO{sub x}, SO{sub x} and particulate matter). Fired with natural or biogas and operated with an efficiency of up to 49 % a significant reduction of fuel costs can be achieved in decentralised applications. Combined heat and power (CHP) configurations add value for a wide range of industrial applications. The exhaust heat of approximately 400 C can be utilised for heating purposes and the production of steam. Besides, it can be also fed directly to adsorption cooling systems. With more than 110 fuel cell power plants operating worldwide, this technology is a serious alternative to conventional gas turbines or gas engines.

Feasibility of Incremental 2-Times Weekly Hemodialysis in Incident Patients With Residual Kidney Function

Directory of Open Access Journals (Sweden)

Andrew I. Chin

2017-09-01

Discussion: More than 50% of incident HD patients with RKF have adequate kidney urea clearance to be considered for 2-times weekly HD. When additionally ultrafiltration volume and blood pressure stability are taken into account, more than one-fourth of the total cohort could optimally start HD in an incremental fashion.

Biomass gasification for CHP with dry gas cleaning and regenerative heat recovery

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-05-01

Small scale CHP plants based on biomass gasification technologies are generally expensive and not very efficient due to gas quality problems which increase operation and maintenance cost as well as breakdown. To overcome this situation the team has developed, integrated and tested a complete biomass gasification combine heat and power prototype plant of 250 kWth equipped with a specifically developed dry gas cleaning and heat recovery system. The dry gas cleaning device is a simple dry gas regenerative heat exchanger where tars are stopped by condensation but working at a temperature above due point in order to avoid water condensation. Two types of heat particles separation devices have been tested in parallel multi-cyclone and ceramic filters. After several month spent on modelling design, construction and optimisation, a full test campaign of 400 hours continuous monitoring has been done where all working parameters has been monitored and gas cleaning device performances has been assessed. Results have shown: Inappropriateness of the ceramic filters for the small scale unit due to operation cost and too high sensibility of the filters to the operation conditions fluctuating in a wide range, despite a very high particle separation efficiency 99 %; Rather good efficiency of the multi-cyclone 72% but not sufficient for engine safety. Additional conventional filters where necessary for the finest part; Inappropriateness of the dry gas heat exchanger device for tar removal partly due to a low tar content of the syngas generated, below 100 mg/Nm{sup 3} , but also due to their composition which would have imposed, to be really efficient, a theoretical condensing temperature of 89 C below the water condensation temperature. These results have been confirmed by laboratory tests and modelling. However the tar cracking phase have shown very interesting results and proved the feasibility of thermal cracking with full cleaning of the heat exchanger without further mechanical

Quantum independent increment processes

CERN Document Server

Franz, Uwe

2006-01-01

This is the second of two volumes containing the revised and completed notes of lectures given at the school "Quantum Independent Increment Processes: Structure and Applications to Physics". This school was held at the Alfried-Krupp-Wissenschaftskolleg in Greifswald in March, 2003, and supported by the Volkswagen Foundation. The school gave an introduction to current research on quantum independent increment processes aimed at graduate students and non-specialists working in classical and quantum probability, operator algebras, and mathematical physics. The present second volume contains the following lectures: "Random Walks on Finite Quantum Groups" by Uwe Franz and Rolf Gohm, "Quantum Markov Processes and Applications in Physics" by Burkhard Kümmerer, Classical and Free Infinite Divisibility and Lévy Processes" by Ole E. Barndorff-Nielsen, Steen Thorbjornsen, and "Lévy Processes on Quantum Groups and Dual Groups" by Uwe Franz.

Development and test of a Stirling engine driven by waste gases for the micro-CHP system

International Nuclear Information System (INIS)

Li Tie; Tang Dawei; Li Zhigang; Du Jinglong; Zhou Tian; Jia Yu

2012-01-01

In recent years, micro-CHP systems are attracting world attention. As one kind of external heating engines, Stirling engines could be applied to the micro-CHP systems driven by solar, biogas, mid-high temperature waste gases and many other heat sources. The development of a Stirling engine driven by mid-high temperature waste gases is presented first. The thermodynamic design method, the key parameters of the designed Stirling engine and its combustion chamber adapted for waste gases are described in detail. Then the performance test of the Stirling engine is carried out. During the test, the temperature of the heater head is monitored by thermocouples, and the pressure of the working fluid helium in the Stirling engine is monitored by pressure sensors. The relationships among the output shaft power, torque and speed are studied, and the pressure losses of the working fluid in the heat exchanger system are also analyzed. The test results demonstrate that the output shaft power could reach 3476 W at 1248 RPM, which is in good agreement with the predicted value of 3901 W at 1500 RPM. The test results confirm the fact that Stirling engines driven by mid-high temperature waste gases are able to achieve a valuable output power for engineering application. - Highlights: ► A β-type Stirling engine whose output power could reach about 3.5 kW is developed by ourselves. ► Waste gases are used as the heat source to drive the Stirling engine. ► Test on the relationship among the power, torque, and speed are presented. ► The pressure changing process of the working fluid in the heat exchanger system during the test is recorded and analyzed.

The intake of long chain omega 3 fatty acids through fish versus capsules results in greater increments of their plasma levels

Directory of Open Access Journals (Sweden)

Visioli Francesco

2004-03-01

Full Text Available Omega 3 fatty acids from fish appear to be more cardioprotective than equivalent amounts provided as capsules. We gave volunteers, for six weeks, either 100 g\\\\day of salmon, providing 383 mg of EPA and 544 mg of DHA or one or three capsules of fish oil\\\\day, providing 150 mg of EPA and 106 mg of DHA or 450 mg of EPA and 318 mg of DHA. We also re-evaluated data from a previous study carried out with the same design. Marked increments in plasma EPA and DHA concentrations (μg\\\\mg total lipid and percentages of total fatty acids were recorded at the end of either treatment. Such increments were linearly and significantly correlated with the dose after capsule administration. Notably, increments in plasma EPA and DHA concentration after salmon intake were significantly higher than after administration of capsules. In fact, the same increments would be obtained with at least two- and nine-fold higher doses of EPA and DHA, respectively, if administered with capsules rather than salmon. In turn, we provide experimental evidence that omega 3 fatty acids from fish are more effectively incorporated into plasma lipids than when administered as capsules and that increments in plasma concentrations of EPA and DHA given as capsules are linearly correlated with their intakes.

Stochastic PSO-based heat and power dispatch under environmental constraints incorporating CHP and wind power units

Energy Technology Data Exchange (ETDEWEB)

Piperagkas, G.S.; Anastasiadis, A.G.; Hatziargyriou, N.D. [National Technical University of Athens, School of Electrical and Computer Engineering, Electric Power Division, 9, Iroon Polytechneiou Str., GR-15773 Zografou, Athens (Greece)

2011-01-15

In this paper an extended stochastic multi-objective model for economic dispatch (ED) is proposed, that incorporates in the optimization process heat and power from CHP units and expected wind power. Stochastic restrictions for the CO{sub 2}, SO{sub 2} and NO{sub x} emissions are used as inequality constraints. The ED problem is solved using a multi-objective particle swarm optimization technique. The available wind power is estimated from a transformation of the wind speed considered as a random variable to wind power. Simulations are performed on the modified IEEE 30 bus network with 2 cogeneration units and actual wind data. Results concerning minimum cost and emissions reduction options are finally drawn. (author)

Growth increments in teeth of Diictodon (Therapsida

Directory of Open Access Journals (Sweden)

J. Francis Thackeray

1991-09-01

Full Text Available Growth increments circa 0.02 mm in width have been observed in sectioned tusks of Diictodon from the Late Permian lower Beaufort succession of the South African Karoo, dated between about 260 and 245 million years ago. Mean growth increments show a decline from relatively high values in the Tropidostoma/Endothiodon Assemblage Zone, to lower values in the Aulacephalodon/Cistecephaluszone, declining still further in the Dicynodon lacerficeps/Whaitsia zone at the end of the Permian. These changes coincide with gradual changes in carbon isotope ratios measured from Diictodon tooth apatite. It is suggested that the decline in growth increments is related to environmental changes associated with a decline in primary production which contributed to the decline in abundance and ultimate extinction of Diictodon.

Incremental Integrity Checking: Limitations and Possibilities

DEFF Research Database (Denmark)

Christiansen, Henning; Martinenghi, Davide

2005-01-01

Integrity checking is an essential means for the preservation of the intended semantics of a deductive database. Incrementality is the only feasible approach to checking and can be obtained with respect to given update patterns by exploiting query optimization techniques. By reducing the problem...... to query containment, we show that no procedure exists that always returns the best incremental test (aka simplification of integrity constraints), and this according to any reasonable criterion measuring the checking effort. In spite of this theoretical limitation, we develop an effective procedure...

Design of methodology for incremental compiler construction

Directory of Open Access Journals (Sweden)

Pavel Haluza

2011-01-01

Full Text Available The paper deals with possibilities of the incremental compiler construction. It represents the compiler construction possibilities for languages with a fixed set of lexical units and for languages with a variable set of lexical units, too. The methodology design for the incremental compiler construction is based on the known algorithms for standard compiler construction and derived for both groups of languages. Under the group of languages with a fixed set of lexical units there belong languages, where each lexical unit has its constant meaning, e.g., common programming languages. For this group of languages the paper tries to solve the problem of the incremental semantic analysis, which is based on incremental parsing. In the group of languages with a variable set of lexical units (e.g., professional typographic system TEX, it is possible to change arbitrarily the meaning of each character on the input file at any time during processing. The change takes effect immediately and its validity can be somehow limited or is given by the end of the input. For this group of languages this paper tries to solve the problem case when we use macros temporarily changing the category of arbitrary characters.

21 CFR 874.1070 - Short increment sensitivity index (SISI) adapter.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Short increment sensitivity index (SISI) adapter. 874.1070 Section 874.1070 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... increment sensitivity index (SISI) adapter. (a) Identification. A short increment sensitivity index (SISI...

A Syntactic-Semantic Approach to Incremental Verification

OpenAIRE

Bianculli, Domenico; Filieri, Antonio; Ghezzi, Carlo; Mandrioli, Dino

2013-01-01

Software verification of evolving systems is challenging mainstream methodologies and tools. Formal verification techniques often conflict with the time constraints imposed by change management practices for evolving systems. Since changes in these systems are often local to restricted parts, an incremental verification approach could be beneficial. This paper introduces SiDECAR, a general framework for the definition of verification procedures, which are made incremental by the framework...

Increased electrical efficiency in biofueled CHP plants by biomass drying; Oekat elutbyte i biobraensleeldade kraftvaermeanlaeggningar med hjaelp av foertorkning

Energy Technology Data Exchange (ETDEWEB)

Berntsson, Mikael; Thorson, Ola; Wennberg, Olle

2010-09-15

In this report, integrated biofuel drying has been studied for two cases. One is the existing CHP plant at ENA Energi AB in Enkoeping and the other is a theoretical case. The thought plant is assumed to have a steam generating performance that is probable for a future CHP plant optimised for power production. The CHP plant at ENA Energi with its integrated bed drying system has been used as a model in this study. The plant has a grate fired boiler with the capacity to co-produce 24 MW electricity and 55 MW heat. It is designed to use biofuel with moisture content between 40 and 55 %. However, the boiler is able to manage even dryer fuels with the moisture content of about 35 % without complications. Since the boiler operates on part load during most of the season, there are free capacity which can be used for delivering heat to the drying system. The increased power production is a result of mainly two factors: Increased demand of heat as the dryer uses district heating and thus improved possibility to produce steam; and, The season of operation can be extended, since the point where the minimum load of the boiler occurs can be pushed forward as a result of increased demand of heat. For future CHP plants, an optimised plant has been used as a model. The steam data is assumed to be 170 bar and 540 deg C with reheating. For this plant, both on-site and offsite drying have been studied. The case study comprises a whole season of operation and the fuel is assumed to be dried from 50 to 10 %. The size of the optimised plant is as to fit the dimension of a main production unit in a district heating net equal to the tenth largest in Sweden. Heat delivery is assumed to be 896 GWh/year and the maximum heat delivery of district heating is 250 MW. The sizing of the boiler is made to maximise the production of electricity, and thus dependent of the drying strategy used. Flue gas condensation is assumed to be used as much as possible. It decreases the basis for power production

CHP HIGHER EDUCATION, SCHOLARSHIPS AND DEMAND ABROAD ARE POLITICS (1942-1947

Directory of Open Access Journals (Sweden)

Suat ZEYREK

2016-04-01

Full Text Available Turkey was followed by a very slow development in the course of the republic’s first year in higher education.By 1955, there are only two universities in the three cities in Turkey.Although the new university will be declared opened by Ismet Inonu’s mouth several times it was not possible for various reasons.Turkey’s economic situation, the shortage of trained personel and it has been hampered by severe conditions of World War II.But even more important excuses should have prevented the spread of higher education in Turkey. This article will be presented in the light of the real causes of the problem of archival sources mentioned above.Period ruling party, the CHP’s higher education policy followed in scholarships and dormitories were investigated.CHP likely to promote higher education in the first primary education spread to the base and thus wants to create a higher demand.For this reason, it is necessary first of all to build infrastructure for higher education institutions and rules.Coming from big cities in different regions of Anatolia youth to take education to all students experience difficulties and inclusive, egalitarian policies were followed.

Two-phase optimizing approach to design assessments of long distance heat transportation for CHP systems

International Nuclear Information System (INIS)

Hirsch, Piotr; Duzinkiewicz, Kazimierz; Grochowski, Michał; Piotrowski, Robert

2016-01-01

Highlights: • New method for long distance heat transportation system effectivity evaluation. • Decision model formulation which reflects time and spatial structure of the problem. • Multi-criteria and complex approach to solving the decision-making problem. • Solver based on simulation-optimization approach with two-phase optimization method. • Sensitivity analysis of the optimization procedure elements. - Abstract: Cogeneration or Combined Heat and Power (CHP) for power plants is a method of putting to use waste heat which would be otherwise released to the environment. This allows the increase in thermodynamic efficiency of the plant and can be a source of environmental friendly heat for District Heating (DH). In the paper CHP for Nuclear Power Plant (NPP) is analyzed with the focus on heat transportation. A method for effectivity and feasibility evaluation of the long distance, high power Heat Transportation System (HTS) between the NPP and the DH network is proposed. As a part of the method the multi-criteria decision-making problem, having the structure of the mathematical programming problem, for optimized selection of design and operating parameters of the HTS is formulated. The constraints for this problem include a static model of HTS, that allows considerations of system lifetime, time variability and spatial topology. Thereby variation of annual heat demand within the DH area, variability of ground temperature, insulation and pipe aging and/or terrain elevation profile can be taken into account in the decision-making process. The HTS construction costs, pumping power, and heat losses are considered as objective functions. In general, the analyzed optimization problem is multi-criteria, hybrid and nonlinear. The two-phase optimization based on optimization-simulation framework is proposed to solve the decision-making problem. The solver introduces a number of assumptions concerning the optimization process. Methods for problem decomposition

Shredder: GPU-Accelerated Incremental Storage and Computation

OpenAIRE

Bhatotia, Pramod; Rodrigues, Rodrigo; Verma, Akshat

2012-01-01

Redundancy elimination using data deduplication and incremental data processing has emerged as an important technique to minimize storage and computation requirements in data center computing. In this paper, we present the design, implementation and evaluation of Shredder, a high performance content-based chunking framework for supporting incremental storage and computation systems. Shredder exploits the massively parallel processing power of GPUs to overcome the CPU bottlenecks of content-ba...

Simulation and comparison of perturb and observe and incremental ...

Indian Academy of Sciences (India)

Perturb and Observe (P & O) algorithm and Incremental conductance algorithm. ... Keywords. Solar array; insolation; MPPT; modelling, P & O; incremental conductance. 1. .... voltage level. It is also ..... Int. J. Advances in Eng. Technol. 133–148.

Efficient incremental relaying

KAUST Repository

Fareed, Muhammad Mehboob

2013-07-01

We propose a novel relaying scheme which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission suffers deep fading. We calculate the packet error rate for the proposed efficient incremental relaying scheme with both amplify and forward and decode and forward relaying. Numerical results are also presented to verify their analytical counterparts. © 2013 IEEE.

B-2 Extremely High Frequency SATCOM and Computer Increment 1 (B-2 EHF Inc 1)

Science.gov (United States)

2015-12-01

Confidence Level Confidence Level of cost estimate for current APB: 55% This APB reflects cost and funding data based on the B-2 EHF Increment I SCP...This cost estimate was quantified at the Mean (~55%) confidence level . Total Quantity Quantity SAR Baseline Production Estimate Current APB...Production Estimate Econ Qty Sch Eng Est Oth Spt Total 33.624 -0.350 1.381 0.375 0.000 -6.075 0.000 -0.620 -5.289 28.335 Current SAR Baseline to Current

Entity versus incremental theories predict older adults' memory performance.

Science.gov (United States)

Plaks, Jason E; Chasteen, Alison L

2013-12-01

The authors examined whether older adults' implicit theories regarding the modifiability of memory in particular (Studies 1 and 3) and abilities in general (Study 2) would predict memory performance. In Study 1, individual differences in older adults' endorsement of the "entity theory" (a belief that one's ability is fixed) or "incremental theory" (a belief that one's ability is malleable) of memory were measured using a version of the Implicit Theories Measure (Dweck, 1999). Memory performance was assessed with a free-recall task. Results indicated that the higher the endorsement of the incremental theory, the better the free recall. In Study 2, older and younger adults' theories were measured using a more general version of the Implicit Theories Measure that focused on the modifiability of abilities in general. Again, for older adults, the higher the incremental endorsement, the better the free recall. Moreover, as predicted, implicit theories did not predict younger adults' memory performance. In Study 3, participants read mock news articles reporting evidence in favor of either the entity or incremental theory. Those in the incremental condition outperformed those in the entity condition on reading span and free-recall tasks. These effects were mediated by pretask worry such that, for those in the entity condition, higher worry was associated with lower performance. Taken together, these studies suggest that variation in entity versus incremental endorsement represents a key predictor of older adults' memory performance. PsycINFO Database Record (c) 2013 APA, all rights reserved.

Marketing opportunities for CHP electricity in a virtual power plant. Direct and indirect marketing of flexibility; Vermarktungschancen fuer KWK-Strom im virtuellen Kraftwerk. Direkte und indirekte Flexibilitaetsvermarktung

Energy Technology Data Exchange (ETDEWEB)

Otto, Achim; Baumgart, Bastian [Trianel GmbH, Aachen (Germany). Abt. Virtuelle Kraftwerke

2013-07-15

The increasingly fluctuating feed-in of electricity by means of a rapid expansion of renewable energies results in an increasing demand for flexible performance for the regulation of production and consumption. An important part of the necessary flexibility could be provided by CHP plants. Their potential of flexibility is not always fully exploited.

Optimisation of Combined Cycle Gas Turbine Power Plant in Intraday Market: Riga CHP-2 Example

Science.gov (United States)

Ivanova, P.; Grebesh, E.; Linkevics, O.

2018-02-01

In the research, the influence of optimised combined cycle gas turbine unit - according to the previously developed EM & OM approach with its use in the intraday market - is evaluated on the generation portfolio. It consists of the two combined cycle gas turbine units. The introduced evaluation algorithm saves the power and heat balance before and after the performance of EM & OM approach by making changes in the generation profile of units. The aim of this algorithm is profit maximisation of the generation portfolio. The evaluation algorithm is implemented in multi-paradigm numerical computing environment MATLab on the example of Riga CHP-2. The results show that the use of EM & OM approach in the intraday market can be profitable or unprofitable. It depends on the initial state of generation units in the intraday market and on the content of the generation portfolio.

Lifetime costs of lung transplantation : Estimation of incremental costs

NARCIS (Netherlands)

VanEnckevort, PJ; Koopmanschap, MA; Tenvergert, EM; VanderBij, W; Rutten, FFH

1997-01-01

Despite an expanding number of centres which provide lung transplantation, information about the incremental costs of lung transplantation is scarce. From 1991 until 1995, in The Netherlands a technology assessment was performed which provided information about the incremental costs of lung

Analysis of a CHP plant in a municipal solid waste landfill in the South of Spain

International Nuclear Information System (INIS)

Chacartegui, Ricardo; Carvalho, Monica; Abrahão, Raphael; Becerra, José

2015-01-01

The most effective strategy to manage and treat solid urban residues, with the least environmental impact as well as lowest economic and energy costs, is a challenge for sustainability in current society, who actually pay for the final management of these residues. This manuscript analyzes the potential of biogas generation in an urban solid residue treatment plant, and the potential use for cogeneration in situ at the landfill. The objective is to identify the energy potential associated with the landfill and its potential use to accelerate the evaporation of leachate through the supply of heat, reducing the risks of exceeding the collection capacity of the leachate ponds. The change in legislation for generation within the special regime in Spain (2014) introduced a sudden change in the direction of energy policies, which affected significantly the profitability of these facilities. This manuscript analyzes the application of both legislations, previous (2007) and current (2014), for the case of a cogeneration system installed in this landfill. The results obtained indicate that even with a much more restrictive legislation in force, acceptable values are obtained for the evaluation of the investment – however, better results were obtained for the previous legislation that favored the special regime. The new regulation constrains the maximum and minimum annual operating hours for landfill cogeneration. It results in relevant periods with limited use of biogas for electricity generation. Biogas storage for delayed future consumption in the same installation and biogas selling for external use in boilers are proposed as options for this biogas in excess. They can reduce greenhouse gases emissions from the non-used biogas and can improve the economic results of the facility. - Highlights: • Analysis of biogas generation capacity in an existing landfill at South of Spain. • Analysis of the integration of gas engine for cogeneration. • CHP integration for

Defense Agencies Initiative Increment 2 (DAI Inc 2)

Science.gov (United States)

2016-03-01

module. In an ADM dated September 23, 2013, the MDA established Increment 2 as a MAIS program to include budget formulation; grants financial...2016 Major Automated Information System Annual Report Defense Agencies Initiative Increment 2 (DAI Inc 2) Defense Acquisition Management...President’s Budget RDT&E - Research, Development, Test, and Evaluation SAE - Service Acquisition Executive TBD - To Be Determined TY - Then

Biometrics Enabling Capability Increment 1 (BEC Inc 1)

Science.gov (United States)

2016-03-01

modal biometrics submissions to include iris, face, palm and finger prints from biometrics collection devices, which will support the Warfighter in...2016 Major Automated Information System Annual Report Biometrics Enabling Capability Increment 1 (BEC Inc 1) Defense Acquisition Management...Phone: 227-3119 DSN Fax: Date Assigned: July 15, 2015 Program Information Program Name Biometrics Enabling Capability Increment 1 (BEC Inc 1) DoD

76 FR 53763 - Immigration Benefits Business Transformation, Increment I

Science.gov (United States)

2011-08-29

..., 100, et al. Immigration Benefits Business Transformation, Increment I; Final Rule #0;#0;Federal... Benefits Business Transformation, Increment I AGENCY: U.S. Citizenship and Immigration Services, DHS... USCIS is engaged in an enterprise-wide transformation effort to implement new business processes and to...

Shakedown analysis by finite element incremental procedures

International Nuclear Information System (INIS)

Borkowski, A.; Kleiber, M.

1979-01-01

It is a common occurence in many practical problems that external loads are variable and the exact time-dependent history of loading is unknown. Instead of it load is characterized by a given loading domain: a convex polyhedron in the n-dimensional space of load parameters. The problem is then to check whether a structure shakes down, i.e. responds elastically after a few elasto-plastic cycles, or not to a variable loading as defined above. Such check can be performed by an incremental procedure. One should reproduce incrementally a simple cyclic process which consists of proportional load paths that connect the origin of the load space with the corners of the loading domain. It was proved that if a structure shakes down to such loading history then it is able to adopt itself to an arbitrary load path contained in the loading domain. The main advantage of such approach is the possibility to use existing incremental finite-element computer codes. (orig.)

Partial and incremental PCMH practice transformation: implications for quality and costs.

Science.gov (United States)

Paustian, Michael L; Alexander, Jeffrey A; El Reda, Darline K; Wise, Chris G; Green, Lee A; Fetters, Michael D

2014-02-01

To examine the associations between partial and incremental implementation of the Patient Centered Medical Home (PCMH) model and measures of cost and quality of care. We combined validated, self-reported PCMH capabilities data with administrative claims data for a diverse statewide population of 2,432 primary care practices in Michigan. These data were supplemented with contextual data from the Area Resource File. We measured medical home capabilities in place as of June 2009 and change in medical home capabilities implemented between July 2009 and June 2010. Generalized estimating equations were used to estimate the mean effect of these PCMH measures on total medical costs and quality of care delivered in physician practices between July 2009 and June 2010, while controlling for potential practice, patient cohort, physician organization, and practice environment confounders. Based on the observed relationships for partial implementation, full implementation of the PCMH model is associated with a 3.5 percent higher quality composite score, a 5.1 percent higher preventive composite score, and $26.37 lower per member per month medical costs for adults. Full PCMH implementation is also associated with a 12.2 percent higher preventive composite score, but no reductions in costs for pediatric populations. Incremental improvements in PCMH model implementation yielded similar positive effects on quality of care for both adult and pediatric populations but were not associated with cost savings for either population. Estimated effects of the PCMH model on quality and cost of care appear to improve with the degree of PCMH implementation achieved and with incremental improvements in implementation. © Health Research and Educational Trust.

The effectiveness of absorption heat pumps application for the increase of economic efficiency of CHP operation

Directory of Open Access Journals (Sweden)

Luzhkovoy Dmitriy S.

2017-01-01

Full Text Available The article deals with a comparative analysis of CHP operational efficiency in various working modes before and after the absorption heat pumps installation. The calculation was performed using a mathematical model of the extraction turbine PT- 80/100-130/13. Absorption heat pumps of LLC “OKB Teplosibmash” were used as AHP models for the analysis. The most effective way of absorption lithium-bromide heat pumps application as a part of the turbine PT-80/100-130/13 turned out to be their usage in a heat-producing mode during a non-heating season with a load of hot water supply. For this mode the dependence of the turbine heat efficiency on the heat load of the external consumer at a given throttle flow was analyzed.

Implementation strategy for small CHP-plants in a competitive market: the case of Lithuania

International Nuclear Information System (INIS)

Lund, H.; Siupsinskas, G.; Martinaitis, V.

2005-01-01

Within five years from now, Lithuania is going to close down Ignalina, the only nuclear-power plant in the country. Since Ignalina generates more than 75% of the Lithuanian electricity production, new generation capacities are needed. Traditional steam-turbines, fuelled with fossil fuels, would mean further imports of fuel as well as a rise in CO 2 emissions. At the same time, several small district-heating companies one suffering from high heating-prices. Typically, the price in small towns is 20-50% higher than the price in large urban areas. Consequently, alternative strategies should be considered. This article analyses the conditions for one such strategy, namely the replacement of boilers in the existing district-heating supplies with combined heat-and-power production (CHP). Compared with new power stations, fuel can be saved and CO 2 -emissions reduced. Also this strategy can be used to level the difference between low heating prices in the large urban areas and high prices in small towns and villages. (Author)

Testing and model-aided analysis of a 2 kW el PEMFC CHP-system

Science.gov (United States)

König, P.; Weber, A.; Lewald, N.; Aicher, T.; Jörissen, L.; Ivers-Tiffée, E.; Szolak, R.; Brendel, M.; Kaczerowski, J.

A prototype PEMFC CHP-system (combined heat and power) for decentralised energy supply in domestic applications has been installed in the Fuel Cell Testing Laboratory at the Institut für Werkstoffe der Elektrotechnik (IWE), Universität Karlsruhe (TH). The system, which was developed at the Zentrum für Sonnenenergie- und Wasserstoff-Forschung ZSW, Ulm (FC-stack) and the Fraunhofer-Institut für Solare Energiesysteme ISE, Freiburg (reformer) is operated and tested in close cooperation with the Stadtwerke Karlsruhe. The tests are carried out as part of the strategic project EDISon, which is supported by the German Federal Ministry of Economics and Technology (BMWA). The performance of the system is evaluated for different operating conditions. The tests include steady state measurements under different electrical and thermal loads as well as an analysis of the dynamic behaviour of the system during load changes. First results of these steady state and dynamic operation characteristics will be presented in this paper.

Automatic incrementalization of Prolog based static analyses

DEFF Research Database (Denmark)

Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

2007-01-01

Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic...... programs and evaluated using incremental tabled evaluation, a technique for efficiently updating memo tables in response to changes in facts and rules. The approach has been implemented and integrated into the Eclipse IDE. Our measurements show that this technique is effective for automatically...

Mission Planning System Increment 5 (MPS Inc 5)

Science.gov (United States)

2016-03-01

2016 Major Automated Information System Annual Report Mission Planning System Increment 5 (MPS Inc 5) Defense Acquisition Management Information...President’s Budget RDT&E - Research, Development, Test, and Evaluation SAE - Service Acquisition Executive TBD - To Be Determined TY - Then Year...Phone: 845-9625 DSN Fax: Date Assigned: May 19, 2014 Program Information Program Name Mission Planning System Increment 5 (MPS Inc 5) DoD

MRI: Modular reasoning about interference in incremental programming

OpenAIRE

Oliveira, Bruno C. D. S; Schrijvers, Tom; Cook, William R

2012-01-01

Incremental Programming (IP) is a programming style in which new program components are defined as increments of other components. Examples of IP mechanisms include: Object-oriented programming (OOP) inheritance, aspect-oriented programming (AOP) advice and feature-oriented programming (FOP). A characteristic of IP mechanisms is that, while individual components can be independently defined, the composition of components makes those components become tightly coupled, sh...

Volatilities, Traded Volumes, and Price Increments in Derivative Securities

Science.gov (United States)

Kim, Kyungsik; Lim, Gyuchang; Kim, Soo Yong; Scalas, Enrico

2007-03-01

We apply the detrended fluctuation analysis (DFA) to the statistics of the Korean treasury bond (KTB) futures from which the logarithmic increments, volatilities, and traded volumes are estimated over a specific time lag. For our case, the logarithmic increment of futures prices has no long-memory property, while the volatility and the traded volume exhibit the existence of long-memory property. To analyze and calculate whether the volatility clustering is due to the inherent higher-order correlation not detected by applying directly the DFA to logarithmic increments of the KTB futures, it is of importance to shuffle the original tick data of futures prices and to generate the geometric Brownian random walk with the same mean and standard deviation. It is really shown from comparing the three tick data that the higher-order correlation inherent in logarithmic increments makes the volatility clustering. Particularly, the result of the DFA on volatilities and traded volumes may be supported the hypothesis of price changes.

Space-time quantitative source apportionment of soil heavy metal concentration increments.

Science.gov (United States)

Yang, Yong; Christakos, George; Guo, Mingwu; Xiao, Lu; Huang, Wei

2017-04-01

Assessing the space-time trends and detecting the sources of heavy metal accumulation in soils have important consequences in the prevention and treatment of soil heavy metal pollution. In this study, we collected soil samples in the eastern part of the Qingshan district, Wuhan city, Hubei Province, China, during the period 2010-2014. The Cd, Cu, Pb and Zn concentrations in soils exhibited a significant accumulation during 2010-2014. The spatiotemporal Kriging technique, based on a quantitative characterization of soil heavy metal concentration variations in terms of non-separable variogram models, was employed to estimate the spatiotemporal soil heavy metal distribution in the study region. Our findings showed that the Cd, Cu, and Zn concentrations have an obvious incremental tendency from the southwestern to the central part of the study region. However, the Pb concentrations exhibited an obvious tendency from the northern part to the central part of the region. Then, spatial overlay analysis was used to obtain absolute and relative concentration increments of adjacent 1- or 5-year periods during 2010-2014. The spatial distribution of soil heavy metal concentration increments showed that the larger increments occurred in the center of the study region. Lastly, the principal component analysis combined with the multiple linear regression method were employed to quantify the source apportionment of the soil heavy metal concentration increments in the region. Our results led to the conclusion that the sources of soil heavy metal concentration increments should be ascribed to industry, agriculture and traffic. In particular, 82.5% of soil heavy metal concentration increment during 2010-2014 was ascribed to industrial/agricultural activities sources. Using STK and SOA to obtain the spatial distribution of heavy metal concentration increments in soils. Using PCA-MLR to quantify the source apportionment of soil heavy metal concentration increments. Copyright © 2017

Design and analysis of permanent magnet moving coil type generator used in a micro-CHP generation system

Science.gov (United States)

Oros Pop, Susana Teodora; Berinde, Ioan; Vadan, Ioan

2015-12-01

This paper presents the design and analysis of a permanent magnet moving coil type generator driven by a free piston Stirling engine. This assemble free piston Stirling engine - permanent magnet moving coil type generator will be used in a combined heat and power (CHP) system for producing heat and power in residential area. The design procedure for moving coil type linear generator starts from the rated power imposed and finally uses the Faraday law of induction. The magneto-static magnetic field generated by permanent magnets is analyzed by means of Reluctance method and Finite Element Method in order to evaluate the magnetic flux density in the air gap, which is a design data imposed in the design stage, and the results are compared.

Support vector machine incremental learning triggered by wrongly predicted samples

Science.gov (United States)

Tang, Ting-long; Guan, Qiu; Wu, Yi-rong

2018-05-01

According to the classic Karush-Kuhn-Tucker (KKT) theorem, at every step of incremental support vector machine (SVM) learning, the newly adding sample which violates the KKT conditions will be a new support vector (SV) and migrate the old samples between SV set and non-support vector (NSV) set, and at the same time the learning model should be updated based on the SVs. However, it is not exactly clear at this moment that which of the old samples would change between SVs and NSVs. Additionally, the learning model will be unnecessarily updated, which will not greatly increase its accuracy but decrease the training speed. Therefore, how to choose the new SVs from old sets during the incremental stages and when to process incremental steps will greatly influence the accuracy and efficiency of incremental SVM learning. In this work, a new algorithm is proposed to select candidate SVs and use the wrongly predicted sample to trigger the incremental processing simultaneously. Experimental results show that the proposed algorithm can achieve good performance with high efficiency, high speed and good accuracy.

Average-case analysis of incremental topological ordering

DEFF Research Database (Denmark)

Ajwani, Deepak; Friedrich, Tobias

2010-01-01

Many applications like pointer analysis and incremental compilation require maintaining a topological ordering of the nodes of a directed acyclic graph (DAG) under dynamic updates. All known algorithms for this problem are either only analyzed for worst-case insertion sequences or only evaluated...... experimentally on random DAGs. We present the first average-case analysis of incremental topological ordering algorithms. We prove an expected runtime of under insertion of the edges of a complete DAG in a random order for the algorithms of Alpern et al. (1990) [4], Katriel and Bodlaender (2006) [18], and Pearce...

Job Embeddedness Demonstrates Incremental Validity When Predicting Turnover Intentions for Australian University Employees

Science.gov (United States)

Heritage, Brody; Gilbert, Jessica M.; Roberts, Lynne D.

2016-01-01

Job embeddedness is a construct that describes the manner in which employees can be enmeshed in their jobs, reducing their turnover intentions. Recent questions regarding the properties of quantitative job embeddedness measures, and their predictive utility, have been raised. Our study compared two competing reflective measures of job embeddedness, examining their convergent, criterion, and incremental validity, as a means of addressing these questions. Cross-sectional quantitative data from 246 Australian university employees (146 academic; 100 professional) was gathered. Our findings indicated that the two compared measures of job embeddedness were convergent when total scale scores were examined. Additionally, job embeddedness was capable of demonstrating criterion and incremental validity, predicting unique variance in turnover intention. However, this finding was not readily apparent with one of the compared job embeddedness measures, which demonstrated comparatively weaker evidence of validity. We discuss the theoretical and applied implications of these findings, noting that job embeddedness has a complementary place among established determinants of turnover intention. PMID:27199817

Motion-Induced Blindness Using Increments and Decrements of Luminance

Directory of Open Access Journals (Sweden)

Stine Wm Wren

2017-10-01

Full Text Available Motion-induced blindness describes the disappearance of stationary elements of a scene when other, perhaps non-overlapping, elements of the scene are in motion. We measured the effects of increment (200.0 cd/m2 and decrement targets (15.0 cd/m2 and masks presented on a grey background (108.0 cd/m2, tapping into putative ON- and OFF-channels, on the rate of target disappearance psychophysically. We presented two-frame motion, which has coherent motion energy, and dynamic Glass patterns and dynamic anti-Glass patterns, which do not have coherent motion energy. Using the method of constant stimuli, participants viewed stimuli of varying durations (3.1 s, 4.6 s, 7.0 s, 11 s, or 16 s in a given trial and then indicated whether or not the targets vanished during that trial. Psychometric function midpoints were used to define absolute threshold mask duration for the disappearance of the target. 95% confidence intervals for threshold disappearance times were estimated using a bootstrap technique for each of the participants across two experiments. Decrement masks were more effective than increment masks with increment targets. Increment targets were easier to mask than decrement targets. Distinct mask pattern types had no effect, suggesting that perceived coherence contributes to the effectiveness of the mask. The ON/OFF dichotomy clearly carries its influence to the level of perceived motion coherence. Further, the asymmetry in the effects of increment and decrement masks on increment and decrement targets might lead one to speculate that they reflect the ‘importance’ of detecting decrements in the environment.

Logistics Modernization Program Increment 2 (LMP Inc 2)

Science.gov (United States)

2016-03-01

Sections 3 and 4 of the LMP Increment 2 Business Case, ADM), key functional requirements, Critical Design Review (CDR) Reports, and Economic ...from the 2013 version of the LMP Increment 2 Economic Analysis and replace it with references to the Economic Analysis that will be completed...of ( inbound /outbound) IDOCs into the system. LMP must be able to successfully process 95% of ( inbound /outbound) IDOCs into the system. Will meet

Incremental Tensor Principal Component Analysis for Handwritten Digit Recognition

Directory of Open Access Journals (Sweden)

Chang Liu

2014-01-01

Full Text Available To overcome the shortcomings of traditional dimensionality reduction algorithms, incremental tensor principal component analysis (ITPCA based on updated-SVD technique algorithm is proposed in this paper. This paper proves the relationship between PCA, 2DPCA, MPCA, and the graph embedding framework theoretically and derives the incremental learning procedure to add single sample and multiple samples in detail. The experiments on handwritten digit recognition have demonstrated that ITPCA has achieved better recognition performance than that of vector-based principal component analysis (PCA, incremental principal component analysis (IPCA, and multilinear principal component analysis (MPCA algorithms. At the same time, ITPCA also has lower time and space complexity.

Optimisation of Combined Cycle Gas Turbine Power Plant in Intraday Market: Riga CHP-2 Example

Directory of Open Access Journals (Sweden)

Ivanova P.

2018-02-01

Full Text Available In the research, the influence of optimised combined cycle gas turbine unit – according to the previously developed EM & OM approach with its use in the intraday market – is evaluated on the generation portfolio. It consists of the two combined cycle gas turbine units. The introduced evaluation algorithm saves the power and heat balance before and after the performance of EM & OM approach by making changes in the generation profile of units. The aim of this algorithm is profit maximisation of the generation portfolio. The evaluation algorithm is implemented in multi-paradigm numerical computing environment MATLab on the example of Riga CHP-2. The results show that the use of EM & OM approach in the intraday market can be profitable or unprofitable. It depends on the initial state of generation units in the intraday market and on the content of the generation portfolio.

A Geothermal Energy Supported Gas-steam Cogeneration Unit as a Possible Replacement for the Old Part of a Municipal CHP Plant (TEKO

Directory of Open Access Journals (Sweden)

L. Böszörményi

2001-01-01

Full Text Available The need for more intensive utilization of local renewable energy sources is indisputable. Under the current economic circumstances their competitiveness in comparison with fossil fuels is rather low, if we do not take into account environmental considerations. Integrating geothermal sources into combined heat and power production in a municipal CHP plant would be an excellent solution to this problem. This concept could lead to an innovative type of power plant - a gas-steam cycle based, geothermal energy supported cogeneration unit.

Validation of the periodicity of growth increment deposition in ...

African Journals Online (AJOL)

Validation of the periodicity of growth increment deposition in otoliths from the larval and early juvenile stages of two cyprinids from the Orange–Vaal river ... Linear regression models were fitted to the known age post-fertilisation and the age estimated using increment counts to test the correspondence between the two for ...

Creating Helical Tool Paths for Single Point Incremental Forming

DEFF Research Database (Denmark)

Skjødt, Martin; Hancock, Michael H.; Bay, Niels

2007-01-01

Single point incremental forming (SPIF) is a relatively new sheet forming process. A sheet is clamped in a rig and formed incrementally using a rotating single point tool in the form of a rod with a spherical end. The process is often performed on a CNC milling machine and the tool movement...

Single point incremental forming: Formability of PC sheets

Science.gov (United States)

Formisano, A.; Boccarusso, L.; Carrino, L.; Lambiase, F.; Minutolo, F. Memola Capece

2018-05-01

Recent research on Single Point Incremental Forming of polymers has slightly covered the possibility of expanding the materials capability window of this flexible forming process beyond metals, by demonstrating the workability of thermoplastic polymers at room temperature. Given the different behaviour of polymers compared to metals, different aspects need to be deepened to better understand the behaviour of these materials when incrementally formed. Thus, the aim of the work is to investigate the formability of incrementally formed polycarbonate thin sheets. To this end, an experimental investigation at room temperature was conducted involving formability tests; varying wall angle cone and pyramid frusta were manufactured by processing polycarbonate sheets with different thicknesses and using tools with different diameters, in order to draw conclusions on the formability of polymer sheets through the evaluation of the forming angles and the observation of the failure mechanisms.

Martingales, nonstationary increments, and the efficient market hypothesis

Science.gov (United States)

McCauley, Joseph L.; Bassler, Kevin E.; Gunaratne, Gemunu H.

2008-06-01

We discuss the deep connection between nonstationary increments, martingales, and the efficient market hypothesis for stochastic processes x(t) with arbitrary diffusion coefficients D(x,t). We explain why a test for a martingale is generally a test for uncorrelated increments. We explain why martingales look Markovian at the level of both simple averages and 2-point correlations. But while a Markovian market has no memory to exploit and cannot be beaten systematically, a martingale admits memory that might be exploitable in higher order correlations. We also use the analysis of this paper to correct a misstatement of the ‘fair game’ condition in terms of serial correlations in Fama’s paper on the EMH. We emphasize that the use of the log increment as a variable in data analysis generates spurious fat tails and spurious Hurst exponents.

Incremental Learning for Place Recognition in Dynamic Environments

OpenAIRE

Luo, Jie; Pronobis, Andrzej; Caputo, Barbara; Jensfelt, Patric

2007-01-01

This paper proposes a discriminative approach to template-based Vision-based place recognition is a desirable feature for an autonomous mobile system. In order to work in realistic scenarios, visual recognition algorithms should be adaptive, i.e. should be able to learn from experience and adapt continuously to changes in the environment. This paper presents a discriminative incremental learning approach to place recognition. We use a recently introduced version of the incremental SVM, which ...

On the instability increments of a stationary pinch

International Nuclear Information System (INIS)

Bud'ko, A.B.

1989-01-01

The stability of stationary pinch to helical modes is numerically studied. It is shown that in the case of a rather fast plasma pressure decrease to the pinch boundary, for example, for an isothermal diffusion pinch with Gauss density distribution instabilities with m=0 modes are the most quickly growing. Instability increments are calculated. A simple analytical expression of a maximum increment of growth of sausage instability for automodel Gauss profiles is obtained

Incremental Trust in Grid Computing

DEFF Research Database (Denmark)

Brinkløv, Michael Hvalsøe; Sharp, Robin

2007-01-01

This paper describes a comparative simulation study of some incremental trust and reputation algorithms for handling behavioural trust in large distributed systems. Two types of reputation algorithm (based on discrete and Bayesian evaluation of ratings) and two ways of combining direct trust and ...... of Grid computing systems....

Convergent systems vs. incremental stability

NARCIS (Netherlands)

Rüffer, B.S.; Wouw, van de N.; Mueller, M.

2013-01-01

Two similar stability notions are considered; one is the long established notion of convergent systems, the other is the younger notion of incremental stability. Both notions require that any two solutions of a system converge to each other. Yet these stability concepts are different, in the sense

Strandby Harbour on solar cooling. Demonstration of 8.000 m{sup 2} solar collectors combined with flue gas cooling with a absorption cooling system; Combined heat and power plant (CHP); Strandby havn paa solkoeling. Demonstration af 8.000 m{sup 2} solfangere kombineret med roeggaskoeling med absorptionskoeleanlaeg

Energy Technology Data Exchange (ETDEWEB)

Soerensen, Flemming (Strandby Varmevaerk, Strandby (Denmark)); Soerensen, Per Alex (PlanEnergi, Skoerping (Denmark)); Ulbjerg, F. (Ramboell, Odense (Denmark)); Sloth, H. (Houe and Olsen, Thisted (Denmark))

2010-04-15

The aim of the project was to demonstrate 1) high solar heating ratio (18% annually) at a decentralized natural gas combined heat and power plant; 2) increased efficiency (5% of the heat consumption) in a natural gas CHP by using an extra flue gas cooler and an absorption heat pump; 3) a double tank system where a new tank during winter is used for cooling/ heat storage for the absorption heat pump and during summer for solar heat storage in serial operation with the old tank. The concept of combining solar power, absorption cooling and natural gas-fired small-scale CHP in Strandby met expectations and could be replicated in other CHP plants. However, it is important to note that if major construction modifications in the flue gas condensation system in the boiler or engine are required, the operating hours must not be reduced significantly in the amortisation period for the conversion. (ln)

Power calculation of linear and angular incremental encoders

Science.gov (United States)

Prokofev, Aleksandr V.; Timofeev, Aleksandr N.; Mednikov, Sergey V.; Sycheva, Elena A.

2016-04-01

Automation technology is constantly expanding its role in improving the efficiency of manufacturing and testing processes in all branches of industry. More than ever before, the mechanical movements of linear slides, rotary tables, robot arms, actuators, etc. are numerically controlled. Linear and angular incremental photoelectric encoders measure mechanical motion and transmit the measured values back to the control unit. The capabilities of these systems are undergoing continual development in terms of their resolution, accuracy and reliability, their measuring ranges, and maximum speeds. This article discusses the method of power calculation of linear and angular incremental photoelectric encoders, to find the optimum parameters for its components, such as light emitters, photo-detectors, linear and angular scales, optical components etc. It analyzes methods and devices that permit high resolutions in the order of 0.001 mm or 0.001°, as well as large measuring lengths of over 100 mm. In linear and angular incremental photoelectric encoders optical beam is usually formulated by a condenser lens passes through the measuring unit changes its value depending on the movement of a scanning head or measuring raster. Past light beam is converting into an electrical signal by the photo-detecter's block for processing in the electrical block. Therefore, for calculating the energy source is a value of the desired value of the optical signal at the input of the photo-detecter's block, which reliably recorded and processed in the electronic unit of linear and angular incremental optoelectronic encoders. Automation technology is constantly expanding its role in improving the efficiency of manufacturing and testing processes in all branches of industry. More than ever before, the mechanical movements of linear slides, rotary tables, robot arms, actuators, etc. are numerically controlled. Linear and angular incremental photoelectric encoders measure mechanical motion and

Making context explicit for explanation and incremental knowledge acquisition

Energy Technology Data Exchange (ETDEWEB)

Brezillon, P. [Univ. Paris (France)

1996-12-31

Intelligent systems may be improved by making context explicit in problem solving. This is a lesson drawn from a study of the reasons why a number of knowledge-based systems (KBSs) failed. We discuss the interest to make context explicit in explanation generation and incremental knowledge acquisition, two important aspects of intelligent systems that aim to cooperate with users. We show how context can be used to better explain and incrementally acquire knowledge. The advantages of using context in explanation and incremental knowledge acquisition are discussed through SEPIT, an expert system for supporting diagnosis and explanation through simulation of power plants. We point out how the limitations of such systems may be overcome by making context explicit.

Three routes forward for biofuels: Incremental, leapfrog, and transitional

International Nuclear Information System (INIS)

Morrison, Geoff M.; Witcover, Julie; Parker, Nathan C.; Fulton, Lew

2016-01-01

This paper examines three technology routes for lowering the carbon intensity of biofuels: (1) a leapfrog route that focuses on major technological breakthroughs in lignocellulosic pathways at new, stand-alone biorefineries; (2) an incremental route in which improvements are made to existing U.S. corn ethanol and soybean biodiesel biorefineries; and (3) a transitional route in which biotechnology firms gain experience growing, handling, or chemically converting lignocellulosic biomass in a lower-risk fashion than leapfrog biorefineries by leveraging existing capital stock. We find the incremental route is likely to involve the largest production volumes and greenhouse gas benefits until at least the mid-2020s, but transitional and leapfrog biofuels together have far greater long-term potential. We estimate that the Renewable Fuel Standard, California's Low Carbon Fuel Standard, and federal tax credits provided an incentive of roughly $1.5–2.5 per gallon of leapfrog biofuel between 2012 and 2015, but that regulatory elements in these policies mostly incentivize lower-risk incremental investments. Adjustments in policy may be necessary to bring a greater focus on transitional technologies that provide targeted learning and cost reduction opportunities for leapfrog biofuels. - Highlights: • Three technological pathways are compared that lower carbon intensity of biofuels. • Incremental changes lead to faster greenhouse gas reductions. • Leapfrog changes lead to greatest long-term potential. • Two main biofuel policies (RFS and LCFS) are largely incremental in nature. • Transitional biofuels offer medium-risk, medium reward pathway.

The benefit of regional diversification of cogeneration investments in Europe: A mean-variance portfolio analysis

Energy Technology Data Exchange (ETDEWEB)

Westner, Guenther, E-mail: guenther.westner@eon-energie.co [E.ON Energy Projects GmbH, Arnulfstrasse 56, 80335 Munich (Germany); Madlener, Reinhard, E-mail: rmadlener@eonerc.rwth-aachen.d [Institute for Future Energy Consumer Needs and Behavior (FCN), Faculty of Business and Economics/E.ON Energy Research Center, RWTH Aachen University, Mathieustrasse 6, 52074 Aachen (Germany)

2010-12-15

The EU Directive 2004/8/EC, concerning the promotion of cogeneration, established principles on how EU member states can support combined heat and power generation (CHP). Up to now, the implementation of these principles into national law has not been uniform, and has led to the adoption of different promotion schemes for CHP across the EU member states. In this paper, we first give an overview of the promotion schemes for CHP in various European countries. In a next step, we take two standard CHP technologies, combined-cycle gas turbines (CCGT-CHP) and engine-CHP, and apply exemplarily four selected support mechanisms used in the four largest European energy markets: feed-in tariffs in Germany; energy efficiency certificates in Italy; benefits through tax reduction in the UK; and purchase obligations for power from CHP generation in France. For contracting companies, it could be of interest to diversify their investment in new CHP facilities regionally over several countries in order to reduce country and regulatory risk. By applying the Mean-Variance Portfolio (MVP) theory, we derive characteristic return-risk profiles of the selected CHP technologies in different countries. The results show that the returns on CHP investments differ significantly depending on the country, the support scheme, and the selected technology studied. While a regional diversification of investments in CCGT-CHP does not contribute to reducing portfolio risks, a diversification of investments in engine-CHP can decrease the risk exposure. - Research highlights: {yields}Preconditions for CHP investments differ significantly between the EU member states. {yields}Regional diversification of CHP investments can reduce the total portfolio risk. {yields}Risk reduction depends on the chosen CHP technology.

Total Quality Service and the Business College

OpenAIRE

James Perotti

1995-01-01

Moving a business college to commit to a total quality service approach is much more difficult than the literature suggests. The commitment to customer satisfaction is the essential focus of total quality service. It is unlikely to occur in business colleges. While small incremental change is readily possible, the values and culture of the faculty and administration prevent the requisite acceptance by the faculty of students as their customers, and acceptance of the faculty as customers of th...

Incrementality in naming and reading complex numerals: Evidence from eyetracking

NARCIS (Netherlands)

Korvorst, M.H.W.; Roelofs, A.P.A.; Levelt, W.J.M.

2006-01-01

Individuals speak incrementally when they interleave planning and articulation. Eyetracking, along with the measurement of speech onset latencies, can be used to gain more insight into the degree of incrementality adopted by speakers. In the current article, two eyetracking experiments are reported

Trial operation of a phosphoric acid fuel cell (PC25) for CHP applications in Europe

Energy Technology Data Exchange (ETDEWEB)

Uhrig, M.; Droste, W.; Wolf, D. [Ruhrgas AG, Dorsten (Germany)

1996-12-31

In Europe, ten 200 kW phosphoric acid fuel cells (PAFCs) produced by ONSI (PC25) are currently in operation. Their operators collaborate closely in the European Fuel Cell Users Group (EFCUG). The experience gained from trial operation by the four German operators - HEAG, HGW/HEW, Thyssengas and Ruhrgas - coincides with that of the other European operators. This experience can generally be regarded as favourable. With a view to using fuel cells in combined heat and power generation (CHP), the project described in this report, which was carried out in cooperation with the municipal utility of Bochum and Gasunie of the Netherlands, aimed at gaining experience with the PC 25 in field operation under the specific operating conditions prevailing in Europe. The work packages included heat-controlled operation, examination of plant behavior with varying gas properties and measurement of emissions under dynamic load conditions. The project received EU funding under the JOULE programme.

OXYGEN UPTAKE KINETICS DURING INCREMENTAL- AND DECREMENTAL-RAMP CYCLE ERGOMETRY

Directory of Open Access Journals (Sweden)

Fadıl Özyener

2011-09-01

Full Text Available The pulmonary oxygen uptake (VO2 response to incremental-ramp cycle ergometry typically demonstrates lagged-linear first-order kinetics with a slope of ~10-11 ml·min-1·W-1, both above and below the lactate threshold (ӨL, i.e. there is no discernible VO2 slow component (or "excess" VO2 above ӨL. We were interested in determining whether a reverse ramp profile would yield the same response dynamics. Ten healthy males performed a maximum incremental -ramp (15-30 W·min-1, depending on fitness. On another day, the work rate (WR was increased abruptly to the incremental maximum and then decremented at the same rate of 15-30 W.min-1 (step-decremental ramp. Five subjects also performed a sub-maximal ramp-decremental test from 90% of ӨL. VO2 was determined breath-by-breath from continuous monitoring of respired volumes (turbine and gas concentrations (mass spectrometer. The incremental-ramp VO2-WR slope was 10.3 ± 0.7 ml·min-1·W-1, whereas that of the descending limb of the decremental ramp was 14.2 ± 1.1 ml·min-1·W-1 (p < 0.005. The sub-maximal decremental-ramp slope, however, was only 9. 8 ± 0.9 ml·min-1·W-1: not significantly different from that of the incremental-ramp. This suggests that the VO2 response in the supra-ӨL domain of incremental-ramp exercise manifest not actual, but pseudo, first-order kinetics

In vitro fermentation characteristics of novel fibers, coconut endosperm fiber and chicory pulp, using canine fecal inoculum.

Science.gov (United States)

de Godoy, M R C; Mitsuhashi, Y; Bauer, L L; Fahey, G C; Buff, P R; Swanson, K S

2015-01-01

The objective of this experiment was to determine the effects of in vitro fermentation of coconut endosperm fiber (CEF), chicory pulp (CHP), and selective blends of these substrates on SCFA production and changes in microbiota using canine fecal inocula. A total of 6 individual substrates, including short-chain fructooligosaccharide (scFOS; a well-established prebiotic source), pectin (PEC; used as a positive control), pelletized cellulose (PC; used as a negative control), beet pulp (BP; considered the gold standard fiber source in pet foods), CEF, and CHP, and 3 CEF:CHP blends (75:25% CEF:CHP [B1], 50:50% CEF:CHP [B2], and 25:75% CEF:CHP [B3]) were tested. Triplicate samples of each substrate were fermented for 0, 8, and 16 h after inoculation. A significant substrate × time interaction (P fiber substrates. Future research should investigate the effects of CEF, CHP, and their blends on gastrointestinal health and fecal quality in dogs.

Finance for incremental housing: current status and prospects for expansion

NARCIS (Netherlands)

Ferguson, B.; Smets, P.G.S.M.

2010-01-01

Appropriate finance can greatly increase the speed and lower the cost of incremental housing - the process used by much of the low/moderate-income majority of most developing countries to acquire shelter. Informal finance continues to dominate the funding of incremental housing. However, new sources

One Step at a Time: SBM as an Incremental Process.

Science.gov (United States)

Conrad, Mark

1995-01-01

Discusses incremental SBM budgeting and answers questions regarding resource equity, bookkeeping requirements, accountability, decision-making processes, and purchasing. Approaching site-based management as an incremental process recognizes that every school system engages in some level of site-based decisions. Implementation can be gradual and…

History Matters: Incremental Ontology Reasoning Using Modules

Science.gov (United States)

Cuenca Grau, Bernardo; Halaschek-Wiener, Christian; Kazakov, Yevgeny

The development of ontologies involves continuous but relatively small modifications. Existing ontology reasoners, however, do not take advantage of the similarities between different versions of an ontology. In this paper, we propose a technique for incremental reasoning—that is, reasoning that reuses information obtained from previous versions of an ontology—based on the notion of a module. Our technique does not depend on a particular reasoning calculus and thus can be used in combination with any reasoner. We have applied our results to incremental classification of OWL DL ontologies and found significant improvement over regular classification time on a set of real-world ontologies.

76 FR 73475 - Immigration Benefits Business Transformation, Increment I; Correction

Science.gov (United States)

2011-11-29

... Benefits Business Transformation, Increment I, 76 FR 53764 (Aug. 29, 2011). The final rule removed form... [CIS No. 2481-09; Docket No. USCIS-2009-0022] RIN 1615-AB83 Immigration Benefits Business Transformation, Increment I; Correction AGENCY: U.S. Citizenship and Immigration Services, DHS. ACTION: Final...

Short-term load forecasting with increment regression tree

Energy Technology Data Exchange (ETDEWEB)

Yang, Jingfei; Stenzel, Juergen [Darmstadt University of Techonology, Darmstadt 64283 (Germany)

2006-06-15

This paper presents a new regression tree method for short-term load forecasting. Both increment and non-increment tree are built according to the historical data to provide the data space partition and input variable selection. Support vector machine is employed to the samples of regression tree nodes for further fine regression. Results of different tree nodes are integrated through weighted average method to obtain the comprehensive forecasting result. The effectiveness of the proposed method is demonstrated through its application to an actual system. (author)

The Comparison of Canopy Height Profiles Extracted from Ku-band Profile Radar Waveforms and LiDAR Data

Directory of Open Access Journals (Sweden)

Hui Zhou

2018-05-01

Full Text Available An airborne Ku-band frequency-modulated continuous waveform (FM-CW profiling radar, Tomoradar, records the backscatter signal from the canopy surface and the underlying ground in the southern boreal forest zone of Finland. The recorded waveforms are transformed into canopy height profiles (CHP with a similar methodology utilized in large-footprint light detection and ranging (LiDAR. The point cloud data simultaneously collected by a Velodyne® VLP-16 LiDAR on-board the same platform represent the frequency of discrete returns, which are also applied to the extraction of the CHP by calculating the gap probability and incremental distribution. To thoroughly explore the relationships of the CHP derived from Tomoradar waveforms and LiDAR data we utilized the effective waveforms of one-stripe field measurements and comparison them with four indicators, including the correlation coefficient, the root-mean-square error (RMSE of the difference, and the coefficient of determination and the RMSE of residuals of linear regression. By setting the Tomoradar footprint as 20 degrees to contain over 95% of the transmitting energy of the main lobe, the results show that 88.17% of the CHPs derived from Tomoradar waveforms correlated well with those from the LiDAR data; 98% of the RMSEs of the difference ranged between 0.002 and 0.01; 79.89% of the coefficients of determination were larger than 0.5; and 98.89% of the RMSEs of the residuals ranged from 0.001 to 0.01. Based on the investigations, we discovered that the locations of the greatest CHP derived from the Tomoradar were obviously deeper than those from the LiDAR, which indicated that the Tomoradar microwave signal had a stronger penetration capability than the LiDAR signal. Meanwhile, there are smaller differences (the average RMSEs of differences is only 0.0042 when the total canopy closure is less than 0.5 and better linear regression results in an area with a relatively open canopy than with a denser

The Time Course of Incremental Word Processing during Chinese Reading

Science.gov (United States)

Zhou, Junyi; Ma, Guojie; Li, Xingshan; Taft, Marcus

2018-01-01

In the current study, we report two eye movement experiments investigating how Chinese readers process incremental words during reading. These are words where some of the component characters constitute another word (an embedded word). In two experiments, eye movements were monitored while the participants read sentences with incremental words…

Switch-mode High Voltage Drivers for Dielectric Electro Active Polymer (DEAP) Incremental Actuators

DEFF Research Database (Denmark)

Thummala, Prasanth

voltage DC-DC converters for driving the DEAP based incremental actuators. The DEAP incremental actuator technology has the potential to be used in various industries, e.g., automotive, space and medicine. The DEAP incremental actuator consists of three electrically isolated and mechanically connected...

Efficient Incremental Checkpointing of Java Programs

DEFF Research Database (Denmark)

Lawall, Julia Laetitia; Muller, Gilles

2000-01-01

This paper investigates the optimization of language-level checkpointing of Java programs. First, we describe how to systematically associate incremental checkpoints with Java classes. While being safe, the genericness of this solution induces substantial execution overhead. Second, to solve...

Single-point incremental forming and formability-failure diagrams

DEFF Research Database (Denmark)

Silva, M.B.; Skjødt, Martin; Atkins, A.G.

2008-01-01

In a recent work [1], the authors constructed a closed-form analytical model that is capable of dealing with the fundamentals of single point incremental forming and explaining the experimental and numerical results published in the literature over the past couple of years. The model is based...... of deformation that are commonly found in general single point incremental forming processes; and (ii) to investigate the formability limits of SPIF in terms of ductile damage mechanics and the question of whether necking does, or does not, precede fracture. Experimentation by the authors together with data...

The future of industrial CHIP in Germany, including the tertiary sector. Papers

Energy Technology Data Exchange (ETDEWEB)

Radgen, P; Schmid, C; Mannsbart, W; Jochem, E

2000-07-01

In 1998 the electricity production in industrial installations in Germany was about 40 TWh. This accounts for 66% of the total electricity production with CHP plants in Germany. The presentation will analyse the developments for industrial CHP throughout the last 10 years and will try to explain the developments. The difficult situation for the industrial CHP shows up from the sharp decrease of the total installed capacity by about 2000 MW during 1996 and 1998, already in approach of the full liberalisation of the electricity market in Germany, which has resulted in further and even more plant shut downs. Based on a survey of the German Association of Industrial Autoproducers and Energy Consumers (VIK) plants with a total capacity of 500 MW were closed down in 1999, and about 60% of the industrial CHP installation are facing serious economic problems. The presentation will show some sample economic calculations for different types of plants (Coal fired steam turbines, gas turbines, IC-engines). These results will be compared to the actual energy cost structures for industrial customers. Based on large over capacity in power generation, the offered electricity prices for industrial customers tend to be in the range off the operating cost of the industrial CHP plants. One way out of this dilemma is sometimes the outsourcing and contracting of CHP installations, which has been and still is a growing business in Germany, and utilities regard these options as a possibility to keep their industrial customers. (orig.)

Complex Incremental Product Innovation in Established Service Firms: A Micro Institutional Perspective

OpenAIRE

Vermeulen, Patrick; Bosch, Frans; Volberda, Henk

2007-01-01

textabstractMany product innovation studies have described key determinants that should lead to successful incremental product innovation. Despite numerous studies suggesting how incremental product innovation should be successfully undertaken, many firms still struggle with this type of innovation. In this paper, we use an institutional perspective to investigate why established firms in the financial services industry struggle with their complex incremental product innovation efforts. We ar...

Incremental Innovation and Competitive Pressure in the Presence of Discrete Innovation

DEFF Research Database (Denmark)

Ghosh, Arghya; Kato, Takao; Morita, Hodaka

2017-01-01

Technical progress consists of improvements made upon the existing technology (incremental innovation) and innovative activities aiming at entirely new technology (discrete innovation). Incremental innovation is often of limited relevance to the new technology invented by successful discrete...

Alveolar gas exchange and tissue oxygenation during incremental treadmill exercise, and their associations with blood O2 carrying capacity

Directory of Open Access Journals (Sweden)

Antti-Pekka E. Rissanen

2012-07-01

Full Text Available The magnitude and timing of oxygenation responses in highly active leg muscle, less active arm muscle, and cerebral tissue, have not been studied with simultaneous alveolar gas exchange measurement during incremental treadmill exercise. Nor is it known, if blood O2 carrying capacity affects the tissue-specific oxygenation responses. Thus, we investigated alveolar gas exchange and tissue (m. vastus lateralis, m. biceps brachii, cerebral cortex oxygenation during incremental treadmill exercise until volitional fatigue, and their associations with blood O2 carrying capacity in 22 healthy men. Alveolar gas exchange was measured, and near-infrared spectroscopy (NIRS was used to monitor relative concentration changes in oxy- (Δ[O2Hb], deoxy- (Δ[HHb] and total hemoglobin (Δ[tHb], and tissue saturation index (TSI. NIRS inflection points (NIP, reflecting changes in tissue-specific oxygenation, were determined and their coincidence with ventilatory thresholds (anaerobic threshold (AT, respiratory compensation point (RC; V-slope method was examined. Blood O2 carrying capacity (total hemoglobin mass (tHb-mass was determined with the CO-rebreathing method. In all tissues, NIPs coincided with AT, whereas RC was followed by NIPs. High tHb-mass associated with leg muscle deoxygenation at peak exercise (e.g., Δ[HHb] from baseline walking to peak exercise vs. tHb-mass: r = 0.64, p < 0.01, but not with arm muscle- or cerebral deoxygenation. In conclusion, regional tissue oxygenation was characterized by inflection points, and tissue oxygenation in relation to alveolar gas exchange during incremental treadmill exercise resembled previous findings made during incremental cycling. It was also found out, that O2 delivery to less active m. biceps brachii may be limited by an accelerated increase in ventilation at high running intensities. In addition, high capacity for blood O2 carrying was associated with a high level of m. vastus lateralis deoxygenation at peak

Do otolith increments allow correct inferences about age and growth of coral reef fishes?

Science.gov (United States)

Booth, D. J.

2014-03-01

Otolith increment structure is widely used to estimate age and growth of marine fishes. Here, I test the accuracy of the long-term otolith increment analysis of the lemon damselfish Pomacentrus moluccensis to describe age and growth characteristics. I compare the number of putative annual otolith increments (as a proxy for actual age) and widths of these increments (as proxies for somatic growth) with actual tagged fish-length data, based on a 6-year dataset, the longest time course for a coral reef fish. Estimated age from otoliths corresponded closely with actual age in all cases, confirming annual increment formation. However, otolith increment widths were poor proxies for actual growth in length [linear regression r 2 = 0.44-0.90, n = 6 fish] and were clearly of limited value in estimating annual growth. Up to 60 % of the annual growth variation was missed using otolith increments, suggesting the long-term back calculations of otolith growth characteristics of reef fish populations should be interpreted with caution.

The Dark Side of Malleability: Incremental Theory Promotes Immoral Behaviors.

Science.gov (United States)

Huang, Niwen; Zuo, Shijiang; Wang, Fang; Cai, Pan; Wang, Fengxiang

2017-01-01

Implicit theories drastically affect an individual's processing of social information, decision making, and action. The present research focuses on whether individuals who hold the implicit belief that people's moral character is fixed (entity theorists) and individuals who hold the implicit belief that people's moral character is malleable (incremental theorists) make different choices when facing a moral decision. Incremental theorists are less likely to make the fundamental attribution error (FAE), rarely make moral judgment based on traits and show more tolerance to immorality, relative to entity theorists, which might decrease the possibility of undermining the self-image when they engage in immoral behaviors, and thus we posit that incremental beliefs facilitate immorality. Four studies were conducted to explore the effect of these two types of implicit theories on immoral intention or practice. The association between implicit theories and immoral behavior was preliminarily examined from the observer perspective in Study 1, and the results showed that people tended to associate immoral behaviors (including everyday immoral intention and environmental destruction) with an incremental theorist rather than an entity theorist. Then, the relationship was further replicated from the actor perspective in Studies 2-4. In Study 2, implicit theories, which were measured, positively predicted the degree of discrimination against carriers of the hepatitis B virus. In Study 3, implicit theories were primed through reading articles, and the participants in the incremental condition showed more cheating than those in the entity condition. In Study 4, implicit theories were primed through a new manipulation, and the participants in the unstable condition (primed incremental theory) showed more discrimination than those in the other three conditions. Taken together, the results of our four studies were consistent with our hypotheses.

The Dark Side of Malleability: Incremental Theory Promotes Immoral Behaviors

Directory of Open Access Journals (Sweden)

Niwen Huang

2017-08-01

Full Text Available Implicit theories drastically affect an individual’s processing of social information, decision making, and action. The present research focuses on whether individuals who hold the implicit belief that people’s moral character is fixed (entity theorists and individuals who hold the implicit belief that people’s moral character is malleable (incremental theorists make different choices when facing a moral decision. Incremental theorists are less likely to make the fundamental attribution error (FAE, rarely make moral judgment based on traits and show more tolerance to immorality, relative to entity theorists, which might decrease the possibility of undermining the self-image when they engage in immoral behaviors, and thus we posit that incremental beliefs facilitate immorality. Four studies were conducted to explore the effect of these two types of implicit theories on immoral intention or practice. The association between implicit theories and immoral behavior was preliminarily examined from the observer perspective in Study 1, and the results showed that people tended to associate immoral behaviors (including everyday immoral intention and environmental destruction with an incremental theorist rather than an entity theorist. Then, the relationship was further replicated from the actor perspective in Studies 2–4. In Study 2, implicit theories, which were measured, positively predicted the degree of discrimination against carriers of the hepatitis B virus. In Study 3, implicit theories were primed through reading articles, and the participants in the incremental condition showed more cheating than those in the entity condition. In Study 4, implicit theories were primed through a new manipulation, and the participants in the unstable condition (primed incremental theory showed more discrimination than those in the other three conditions. Taken together, the results of our four studies were consistent with our hypotheses.

Scalable Prediction of Energy Consumption using Incremental Time Series Clustering

Energy Technology Data Exchange (ETDEWEB)

Simmhan, Yogesh; Noor, Muhammad Usman

2013-10-09

Time series datasets are a canonical form of high velocity Big Data, and often generated by pervasive sensors, such as found in smart infrastructure. Performing predictive analytics on time series data can be computationally complex, and requires approximation techniques. In this paper, we motivate this problem using a real application from the smart grid domain. We propose an incremental clustering technique, along with a novel affinity score for determining cluster similarity, which help reduce the prediction error for cumulative time series within a cluster. We evaluate this technique, along with optimizations, using real datasets from smart meters, totaling ~700,000 data points, and show the efficacy of our techniques in improving the prediction error of time series data within polynomial time.

Enabling Incremental Query Re-Optimization.

Science.gov (United States)

Liu, Mengmeng; Ives, Zachary G; Loo, Boon Thau

2016-01-01

As declarative query processing techniques expand to the Web, data streams, network routers, and cloud platforms, there is an increasing need to re-plan execution in the presence of unanticipated performance changes. New runtime information may affect which query plan we prefer to run. Adaptive techniques require innovation both in terms of the algorithms used to estimate costs , and in terms of the search algorithm that finds the best plan. We investigate how to build a cost-based optimizer that recomputes the optimal plan incrementally given new cost information, much as a stream engine constantly updates its outputs given new data. Our implementation especially shows benefits for stream processing workloads. It lays the foundations upon which a variety of novel adaptive optimization algorithms can be built. We start by leveraging the recently proposed approach of formulating query plan enumeration as a set of recursive datalog queries ; we develop a variety of novel optimization approaches to ensure effective pruning in both static and incremental cases. We further show that the lessons learned in the declarative implementation can be equally applied to more traditional optimizer implementations.

Energy Management for Community Energy Network with CHP Based on Cooperative Game

Directory of Open Access Journals (Sweden)

Xiaofeng Liu

2018-04-01

Full Text Available Integrated energy system (IES has received increasing attention in micro grid due to the high energy efficiency and low emission of carbon dioxide. Based on the technology of combined heat and power (CHP, this paper develops a novel operation mechanism with community micro turbine and shared energy storage system (ESS for energy management of prosumers. In the proposed framework, micro-grid operator (MGO equipped with micro turbine and ESS provides energy selling business and ESS leasing business for prosumers. Prosumers can make energy trading with public grid and MGO, and ESS will be shared among prosumers when they pay for the rent to MGO. Based on such framework, we adopt a cooperative game for prosumers to determine optimal energy trading strategies from MGO and public grid for the next day. Concretely, a cooperative game model is formulated to search the optimal strategies aiming at minimizing the daily cost of coalition, and then a bilateral Shapley value (BSV is proposed to solve the allocation problem of coalition’s cost among prosumers. To verify the effectiveness of proposed energy management framework, a practical example is conducted with a community energy network containing MGO and 10 residential buildings. Simulation results show that the proposed scheme is able to provide financial benefits to all prosumers, while providing peak load leveling for the grid.

Structural and incremental validity of the Wechsler Adult Intelligence Scale-Fourth Edition with a clinical sample.

Science.gov (United States)

Nelson, Jason M; Canivez, Gary L; Watkins, Marley W

2013-06-01

Structural and incremental validity of the Wechsler Adult Intelligence Scale-Fourth Edition (WAIS-IV; Wechsler, 2008a) was examined with a sample of 300 individuals referred for evaluation at a university-based clinic. Confirmatory factor analysis indicated that the WAIS-IV structure was best represented by 4 first-order factors as well as a general intelligence factor in a direct hierarchical model. The general intelligence factor accounted for the most common and total variance among the subtests. Incremental validity analyses indicated that the Full Scale IQ (FSIQ) generally accounted for medium to large portions of academic achievement variance. For all measures of academic achievement, the first-order factors combined accounted for significant achievement variance beyond that accounted for by the FSIQ, but individual factor index scores contributed trivial amounts of achievement variance. Implications for interpreting WAIS-IV results are discussed. (PsycINFO Database Record (c) 2013 APA, all rights reserved).

Generic Combined Heat and Power (CHP Model for the Concept Phase of Energy Planning Process

Directory of Open Access Journals (Sweden)

Satya Gopisetty

2016-12-01

Full Text Available Micro gas turbines (MGTs are regarded as combined heat and power (CHP units which offer high fuel utilization and low emissions. They are applied in decentralized energy generation. To facilitate the planning process of energy systems, namely in the context of the increasing application of optimization techniques, there is a need for easy-to-parametrize component models with sufficient accuracy which allow a fast computation. In this paper, a model is proposed where the non-linear part load characteristics of the MGT are linearized by means of physical insight of the working principles of turbomachinery. Further, it is shown that the model can be parametrized by the data usually available in spec sheets. With this model a uniform description of MGTs from several manufacturers covering an electrical power range from 30 k W to 333 k W can be obtained. The MGT model was implemented by means of Modelica/Dymola. The resulting MGT system model, comprising further heat exchangers and hydraulic components, was validated using the experimental data of a 65 k W MGT from a trigeneration energy system.

A feasible system integrating combined heating and power system with ground-source heat pump

International Nuclear Information System (INIS)

Li, HongQiang; Kang, ShuShuo; Yu, Zhun; Cai, Bo; Zhang, GuoQiang

2014-01-01

A system integrating CHP (combined heating and power) subsystem based on natural gas and GSHP (ground-source heat pump subsystem) in series is proposed. By help of simulation software-Aspen Plus, the energy performance of a typical CHP and GSHP-S (S refers to ‘in series’) system was analyzed. The results show that the system can make a better use of waste heat in flue gas from CHP (combined heating and power subsystem). The total system energy efficiency is 123% and the COP (coefficient of performance) of GSHP (ground-source heat pump) subsystem is 5.3. A referenced CHP and GSHP-P (P refers to ‘in parallel’) system is used for comparison; its total system energy efficiency and COP of GSHP subsystem are 118.6% and 3.5 respectively. Compared with CHP and GSHP-P system with different operating parameters, the CHP and GSHP-S system can increase total system energy efficiency by 0.8–34.7%, with related output ratio of heat to power (R) from 1.9 to 18.3. Furthermore, the COP of GSHP subsystem can be increased between the range 3.6 and 6, which is much higher than that in conventional CHP and GSHP-P system. This study will be helpful for other efficient GSHP systems integrating if there is waste heat or other heat resources with low temperature. - Highlights: • CHP system based on natural gas and ground source heat pump. • The new system can make a better utilization of waste heat in flue gas by a special way. • The proposed system can realize energy saving potential from 0.8 to 34.7%. • The coefficient of performance of ground source heat pump subsystem is significantly improved from 3.5 to 3.6–6. • Warm water temperature and percentage of flue gas used to reheat are key parameters

Context-dependent incremental timing cells in the primate hippocampus.

Science.gov (United States)

Sakon, John J; Naya, Yuji; Wirth, Sylvia; Suzuki, Wendy A

2014-12-23

We examined timing-related signals in primate hippocampal cells as animals performed an object-place (OP) associative learning task. We found hippocampal cells with firing rates that incrementally increased or decreased across the memory delay interval of the task, which we refer to as incremental timing cells (ITCs). Three distinct categories of ITCs were identified. Agnostic ITCs did not distinguish between different trial types. The remaining two categories of cells signaled time and trial context together: One category of cells tracked time depending on the behavioral action required for a correct response (i.e., early vs. late release), whereas the other category of cells tracked time only for those trials cued with a specific OP combination. The context-sensitive ITCs were observed more often during sessions where behavioral learning was observed and exhibited reduced incremental firing on incorrect trials. Thus, single primate hippocampal cells signal information about trial timing, which can be linked with trial type/context in a learning-dependent manner.

Statistics of wind direction and its increments

International Nuclear Information System (INIS)

Doorn, Eric van; Dhruva, Brindesh; Sreenivasan, Katepalli R.; Cassella, Victor

2000-01-01

We study some elementary statistics of wind direction fluctuations in the atmosphere for a wide range of time scales (10 -4 sec to 1 h), and in both vertical and horizontal planes. In the plane parallel to the ground surface, the direction time series consists of two parts: a constant drift due to large weather systems moving with the mean wind speed, and fluctuations about this drift. The statistics of the direction fluctuations show a rough similarity to Brownian motion but depend, in detail, on the wind speed. This dependence manifests itself quite clearly in the statistics of wind-direction increments over various intervals of time. These increments are intermittent during periods of low wind speeds but Gaussian-like during periods of high wind speeds. (c) 2000 American Institute of Physics

Incremental prognostic value of coronary computed tomographic angiography high-risk plaque characteristics in newly symptomatic patients.

Science.gov (United States)

Fujimoto, Shinichiro; Kondo, Takeshi; Takamura, Kazuhisa; Baber, Usman; Shinozaki, Tomohiro; Nishizaki, Yuji; Kawaguchi, Yuko; Matsumori, Rie; Hiki, Makoto; Miyauchi, Katsumi; Daida, Hiroyuki; Hecht, Harvey; Stone, Gregg W; Narula, Jagat

2016-06-01

The incremental prognostic value of the plaque features in coronary computed tomographic angiography (CTA) has not been well assessed. This study was designed to determine whether CTA high-risk plaques have prognostic value incremental to the Framingham risk score (FRS) and the severity of luminal obstruction. A total of 628 newly symptomatic patients without known coronary artery disease underwent CTA. They were followed for a median of 677 days during which there were 26 cardiac events, including cardiac death, acute myocardial infarction, and hospitalization for unstable angina. Incremental prognostic value of adding plaque characteristics to the number of diseased vessels and the FRS was evaluated using 3 Cox models and net reclassification indexes. The discrimination index was significantly increased by adding the number of diseased vessels to the FRS (change in c-statistic from 65.8% to 78.6%, p=0.028) but not significantly by further adding plaque characteristics (change in c-statistic from 78.6% to 80.0%, p=0.812). However, improved model-fitting by adding plaque characteristics into the linear combination with risk score and the number of diseased vessels (p=0.007 from likelihood ratio test) and the lowest value of Akaike's information criteria of that model indicated that plaque characteristics improved both predictive accuracy and discrimination perspective. More subjects reclassified by plaque characteristics were moved to directions consistent with their subsequent cardiac event status than in an inconsistent direction. Evaluation of CTA plaque characteristics may provide incremental prognostic value to the number of diseased vessels and the FRS. Copyright © 2015 Japanese College of Cardiology. Published by Elsevier Ltd. All rights reserved.

Incremental Beliefs of Ability, Achievement Emotions and Learning of Singapore Students

Science.gov (United States)

Luo, Wenshu; Lee, Kerry; Ng, Pak Tee; Ong, Joanne Xiao Wei

2014-01-01

This study investigated the relationships of students' incremental beliefs of math ability to their achievement emotions, classroom engagement and math achievement. A sample of 273 secondary students in Singapore were administered measures of incremental beliefs of math ability, math enjoyment, pride, boredom and anxiety, as well as math classroom…

The Cognitive Underpinnings of Incremental Rehearsal

Science.gov (United States)

Varma, Sashank; Schleisman, Katrina B.

2014-01-01

Incremental rehearsal (IR) is a flashcard technique that has been developed and evaluated by school psychologists. We discuss potential learning and memory effects from cognitive psychology that may explain the observed superiority of IR over other flashcard techniques. First, we propose that IR is a form of "spaced practice" that…

Factors that are influencing the economical efficiency of the CHP plants

International Nuclear Information System (INIS)

Ruieneanu, Liviu; Ion, Mircea

2004-01-01

This paper presents some factors that might influence the economical efficiency of a cogeneration plant. These factors are: the understanding of the fuel economy at consumers; - the influence of the electricity production efficiency; - the influence of exergy losses. The statistical data for different countries of Europe show that under the conditions of a deregulated liberalized market of energy the cogeneration plants have numerous financial difficulties. Even if the use of cogeneration ensures a fuel saving, if this economy it is not obvious for the consumers, those consumers might prefer for the production of heat the use of a heat only generating plant. This trend might spread rapidly if the increase of the electricity will not be present immediately in the bill of the consumers that renounce to the heat produced by the CHP plant. The method used for cost allocation on both types of energy has also a great importance, because it might facilitate the rehabilitation measures and doing so it might allow lower prices for both types of energy. Perhaps the most important factor for the economical efficiency of the plant are the exergy losses. The analysis presented above shows two things, namely: - that the electricity production has a very high price, and this cost might be lowered down by some rehabilitation measures (for example repowering); - and that the heat only plants (boilers) are not affected by the exergy losses and that's why if we analyse only the heat production, the use of cogeneration might seem inappropriate

The Dark Side of Malleability: Incremental Theory Promotes Immoral Behaviors

OpenAIRE

Huang, Niwen; Zuo, Shijiang; Wang, Fang; Cai, Pan; Wang, Fengxiang

2017-01-01

Implicit theories drastically affect an individual’s processing of social information, decision making, and action. The present research focuses on whether individuals who hold the implicit belief that people’s moral character is fixed (entity theorists) and individuals who hold the implicit belief that people’s moral character is malleable (incremental theorists) make different choices when facing a moral decision. Incremental theorists are less likely to make the fundamental attribution err...

Organization Strategy and Structural Differences for Radical Versus Incremental Innovation

OpenAIRE

John E. Ettlie; William P. Bridges; Robert D. O'Keefe

1984-01-01

The purpose of this study was to test a model of the organizational innovation process that suggests that the strategy-structure causal sequence is differentiated by radical versus incremental innovation. That is, unique strategy and structure will be required for radical innovation, especially process adoption, while more traditional strategy and structure arrangements tend to support new product introduction and incremental process adoption. This differentiated theory is strongly supported ...

Incremental deformation: A literature review

Directory of Open Access Journals (Sweden)

Nasulea Daniel

2017-01-01

Full Text Available Nowadays the customer requirements are in permanent changing and according with them the tendencies in the modern industry is to implement flexible manufacturing processes. In the last decades, metal forming gained attention of the researchers and considerable changes has occurred. Because for a small number of parts, the conventional metal forming processes are expensive and time-consuming in terms of designing and manufacturing preparation, the manufacturers and researchers became interested in flexible processes. One of the most investigated flexible processes in metal forming is incremental sheet forming (ISF. ISF is an advanced flexible manufacturing process which allows to manufacture complex 3D products without expensive dedicated tools. In most of the cases it is needed for an ISF process the following: a simple tool, a fixing device for sheet metal blank and a universal CNC machine. Using this process it can be manufactured axis-symmetric parts, usually using a CNC lathe but also complex asymmetrical parts using CNC milling machines, robots or dedicated equipment. This paper aim to present the current status of incremental sheet forming technologies in terms of process parameters and their influences, wall thickness distribution, springback effect, formability, surface quality and the current main research directions.

Complex Incremental Product Innovation in Established Service Firms: A Micro Institutional Perspective

NARCIS (Netherlands)

P.A.M. Vermeulen (Patrick); F.A.J. van den Bosch (Frans); H.W. Volberda (Henk)

2006-01-01

textabstractMany product innovation studies have described key determinants that should lead to successful incremental product innovation. Despite numerous studies suggesting how incremental product innovation should be successfully undertaken, many firms still struggle with this type of innovation.

Complex Incremental Product Innovation in Established Service Firms: A Micro Institutional Perspective

NARCIS (Netherlands)

P.A.M. Vermeulen (Patrick); F.A.J. van den Bosch (Frans); H.W. Volberda (Henk)

2007-01-01

textabstractMany product innovation studies have described key determinants that should lead to successful incremental product innovation. Despite numerous studies suggesting how incremental product innovation should be successfully undertaken, many firms still struggle with this type of innovation.

Teraflop-scale Incremental Machine Learning

OpenAIRE

Özkural, Eray

2011-01-01

We propose a long-term memory design for artificial general intelligence based on Solomonoff's incremental machine learning methods. We use R5RS Scheme and its standard library with a few omissions as the reference machine. We introduce a Levin Search variant based on Stochastic Context Free Grammar together with four synergistic update algorithms that use the same grammar as a guiding probability distribution of programs. The update algorithms include adjusting production probabilities, re-u...

A Self-Organizing Incremental Neural Network based on local distribution learning.

Science.gov (United States)

Xing, Youlu; Shi, Xiaofeng; Shen, Furao; Zhou, Ke; Zhao, Jinxi

2016-12-01

In this paper, we propose an unsupervised incremental learning neural network based on local distribution learning, which is called Local Distribution Self-Organizing Incremental Neural Network (LD-SOINN). The LD-SOINN combines the advantages of incremental learning and matrix learning. It can automatically discover suitable nodes to fit the learning data in an incremental way without a priori knowledge such as the structure of the network. The nodes of the network store rich local information regarding the learning data. The adaptive vigilance parameter guarantees that LD-SOINN is able to add new nodes for new knowledge automatically and the number of nodes will not grow unlimitedly. While the learning process continues, nodes that are close to each other and have similar principal components are merged to obtain a concise local representation, which we call a relaxation data representation. A denoising process based on density is designed to reduce the influence of noise. Experiments show that the LD-SOINN performs well on both artificial and real-word data. Copyright © 2016 Elsevier Ltd. All rights reserved.

Incremental Reconstruction of Urban Environments by Edge-Points Delaunay Triangulation

OpenAIRE

Romanoni, Andrea; Matteucci, Matteo

2016-01-01

Urban reconstruction from a video captured by a surveying vehicle constitutes a core module of automated mapping. When computational power represents a limited resource and, a detailed map is not the primary goal, the reconstruction can be performed incrementally, from a monocular video, carving a 3D Delaunay triangulation of sparse points; this allows online incremental mapping for tasks such as traversability analysis or obstacle avoidance. To exploit the sharp edges of urban landscape, we ...

Quasi-static incremental behavior of granular materials: Elastic-plastic coupling and micro-scale dissipation

Science.gov (United States)

Kuhn, Matthew R.; Daouadji, Ali

2018-05-01

The paper addresses a common assumption of elastoplastic modeling: that the recoverable, elastic strain increment is unaffected by alterations of the elastic moduli that accompany loading. This assumption is found to be false for a granular material, and discrete element (DEM) simulations demonstrate that granular materials are coupled materials at both micro- and macro-scales. Elasto-plastic coupling at the macro-scale is placed in the context of thermomechanics framework of Tomasz Hueckel and Hans Ziegler, in which the elastic moduli are altered by irreversible processes during loading. This complex behavior is explored for multi-directional loading probes that follow an initial monotonic loading. An advanced DEM model is used in the study, with non-convex non-spherical particles and two different contact models: a conventional linear-frictional model and an exact implementation of the Hertz-like Cattaneo-Mindlin model. Orthotropic true-triaxial probes were used in the study (i.e., no direct shear strain), with tiny strain increments of 2 ×10-6 . At the micro-scale, contact movements were monitored during small increments of loading and load-reversal, and results show that these movements are not reversed by a reversal of strain direction, and some contacts that were sliding during a loading increment continue to slide during reversal. The probes show that the coupled part of a strain increment, the difference between the recoverable (elastic) increment and its reversible part, must be considered when partitioning strain increments into elastic and plastic parts. Small increments of irreversible (and plastic) strain and contact slipping and frictional dissipation occur for all directions of loading, and an elastic domain, if it exists at all, is smaller than the strain increment used in the simulations.

Survey of controllability in decentralized CHP plants. Optimal operation of priority production units; Kortlaegning af decentrale kraftvarmevaerkers regulerbarhed. Optimal drift af prioriterede anlaeg - Teknologisk grundlag

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-03-15

The present report presents results from two closely related projects, carried out in parallel, under the PSO-F and U 2002. The one project is 'Survey of controllability in de-centralized combined heat and power plants' project number PSO 4724 and is fully reported here. The other project: 'Optimal operation of priority production units, project number PSO 4712, only the part project 'Technological foundations is reported here. In project 4724 the technical conditions that matter regarding controllability of electricity production in de-centralized heat and power stations are surveyed. In this context the term controllability means how fast and to which extent the load factors of the plants can be changed. Also, is has been investigated which options are available for improving the controllability, their potentials and estimates on required investments associated. The investigation covers CHP plants having a production capacity of up to 30 MW of electricity. The main part of the de-centralized CHP plants are based on spark ignited internal combustion engines (Otto engines). Most of these engines are fuelled by natural gas and a smaller part by biogas. A minor number are gas turbines fuelled by natural gas and steam turbines in industrial applications, waste incineration plants or in combined cycle power plants. The mapping has among others consisted of a number of visits on selected different types of plants including interview with people responsible for the daily operation. From these interviews data on the actual operating strategy and technical data have been provided. In addition suppliers of engines and other equipment involved have been contacted for technical information or recommendations regarding possible changes in operation strategy. Searching the Internet has been widely used for identification of technical investigations concerning e.g. operation and maintenance of relevant equipment. Finally, substantial statistical data from

Political dynamics promoting the incremental regulation of secondhand smoke: a case study of New South Wales, Australia

Directory of Open Access Journals (Sweden)

Chapman Simon

2006-07-01

finish the job. Publicity to the growing number of state and national governments that have successfully implemented total bans over the past decade is likely to make incrementalism an increasingly unattractive political option.

An implementation of the diagnosis method DYANA, applied to a combined heat-power device

Energy Technology Data Exchange (ETDEWEB)

Van der Neut, F.

1993-10-01

The development and implementation of the monitor-and-diagnosis method DYANA is presented. This implementation is applied to and tested on a combined heat and power generating device (CHP). The steps that have been taken in realizing this implementation are evaluated into detail . In chapter two the theory behind DYANA is recapitulated. Attention is paid to the basic theory of diagnoses, and the steps of the path from this theory to the algorithm DYANA are revealed. These steps include the hierarchical approach, and explain the following features of DYANA: a) the use of best-first dynamic model zooming based on heuristics with respect to parsimony of the number of components within the diagnoses, b) the use of consistency of fault models with observations to focus on the most likely diagnoses, and c) the use of online diagnosis: the current set of diagnoses is incrementally updated after a new observation of the system is made. In chapter three the relevant aspects of the system to be diagnosed, the CHP, are dealt with in detail. An explanation is given of the broad working of the CHP, its hierarchical structure and mathematical representation are given, CHP observation is commented, and some possible forms of fault models are stated. In chapter four the pseudocode of the implementation, developed for DYANA, is presented. The pseudocode consists of two parts: the monitoring process (using numerical simulation), and the diagnostic process. The differences between the pseudocode and the actual implementation are mentioned. The CHP will then be monitored and diagnosed with this algorithm and results of this test are given in chapter five. An actual implementation of DYANA can be found in a separately supplied appendix, the Programme Appendix. The implementation of the monitoring process is meant only for this example of the CHP. The code for the diagnostic process can be easily adjusted for diagnosing other devices, such as electronic circuits. The language is Pascal.

Estimating increment-decrement life tables with multiple covariates from panel data: the case of active life expectancy.

Science.gov (United States)

Land, K C; Guralnik, J M; Blazer, D G

1994-05-01

A fundamental limitation of current multistate life table methodology-evident in recent estimates of active life expectancy for the elderly-is the inability to estimate tables from data on small longitudinal panels in the presence of multiple covariates (such as sex, race, and socioeconomic status). This paper presents an approach to such an estimation based on an isomorphism between the structure of the stochastic model underlying a conventional specification of the increment-decrement life table and that of Markov panel regression models for simple state spaces. We argue that Markov panel regression procedures can be used to provide smoothed or graduated group-specific estimates of transition probabilities that are more stable across short age intervals than those computed directly from sample data. We then join these estimates with increment-decrement life table methods to compute group-specific total, active, and dependent life expectancy estimates. To illustrate the methods, we describe an empirical application to the estimation of such life expectancies specific to sex, race, and education (years of school completed) for a longitudinal panel of elderly persons. We find that education extends both total life expectancy and active life expectancy. Education thus may serve as a powerful social protective mechanism delaying the onset of health problems at older ages.

Automatic incrementalization of Prolog based static analyses

DEFF Research Database (Denmark)

Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

2007-01-01

Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic prog...

Sociobehavioral Factors Associated with Caries Increment: A Longitudinal Study from 24 to 36 Months Old Children in Thailand

Directory of Open Access Journals (Sweden)

Karl Peltzer

2014-10-01

Full Text Available The aim of this study is to investigate sociobehavioral risk factors from the prenatal period until 36 months of age, and the caries increment from 24 to 36 months of the child in Thailand. The data utilized in this study come from the prospective cohort study of Thai children (PCTC from prenatal to 36 months of the child in Mueang Nan district, Northern Thailand. The total sample size recruited was 783 infants. The sample size with dental caries data was 603 and 597, at 24 months and at 36 months, respectively. The sample size of having two assessment points with a dental examination (at 24 months and at 36 months was 597. Results indicate that the caries increment was 52.9%, meaning from 365 caries free children at 24 months 193 had developed dental caries at 36 months. The prevalence of dental caries was 34.2% at 24 months (n = 206 and 68.5% at 36 months of age (n = 409. In bivariate analysis, higher education of the mother, lower household income, bottle feeding of the infant, frequent sweet candy consumptions, and using rain or well water as drinking water were associated with dental caries increment, while in multivariate conditional logistic regression analysis lower household income, higher education of the mother, and using rain or well water as drinking water remained associated with dental caries increment. In conclusion, a very significant increase in caries development was observed, and oral health may be influenced by sociobehavioural risk factors.

A new recursive incremental algorithm for building minimal acyclic deterministic finite automata

NARCIS (Netherlands)

Watson, B.W.; Martin-Vide, C.; Mitrana, V.

2003-01-01

This chapter presents a new algorithm for incrementally building minimal acyclic deterministic finite automata. Such minimal automata are a compact representation of a finite set of words (e.g. in a spell checker). The incremental aspect of such algorithms (where the intermediate automaton is

Global Combat Support System - Army Increment 2 (GCSS-A Inc 2)

Science.gov (United States)

2016-03-01

2016 Major Automated Information System Annual Report Global Combat Support System - Army Increment 2 (GCSS-A Inc 2) Defense Acquisition...Secretary of Defense PB - President’s Budget RDT&E - Research, Development, Test, and Evaluation SAE - Service Acquisition Executive TBD - To Be...Date Assigned: Program Information Program Name Global Combat Support System - Army Increment 2 (GCSS-A Inc 2) DoD Component Army Responsible

The balanced scorecard: an incremental approach model to health care management.

Science.gov (United States)

Pineno, Charles J

2002-01-01

The balanced scorecard represents a technique used in strategic management to translate an organization's mission and strategy into a comprehensive set of performance measures that provide the framework for implementation of strategic management. This article develops an incremental approach for decision making by formulating a specific balanced scorecard model with an index of nonfinancial as well as financial measures. The incremental approach to costs, including profit contribution analysis and probabilities, allows decisionmakers to assess, for example, how their desire to meet different health care needs will cause changes in service design. This incremental approach to the balanced scorecard may prove to be useful in evaluating the existence of causality relationships between different objective and subjective measures to be included within the balanced scorecard.

Scheduling and Mapping in an Incremental Design Methodology for Distributed Real-Time Embedded Systems

DEFF Research Database (Denmark)

Pop, Paul; Eles, Petru; Peng, Zebo

2004-01-01

In this paper we present an approach to mapping and scheduling of distributed embedded systems for hard real-time applications, aiming at a minimization of the system modification cost. We consider an incremental design process that starts from an already existing system running a set of applicat......In this paper we present an approach to mapping and scheduling of distributed embedded systems for hard real-time applications, aiming at a minimization of the system modification cost. We consider an incremental design process that starts from an already existing system running a set...... be added to the resulted system. Thus, we propose a heuristic which finds the set of already running applications which have to be remapped and rescheduled at the same time with mapping and scheduling the new application, such that the disturbance on the running system (expressed as the total cost implied...... by the modifications) is minimized. Once this set of applications has been determined, we outline a mapping and scheduling algorithm aimed at fulfilling the requirements stated above. The approaches have been evaluated based on extensive experiments using a large number of generated benchmarks as well as a real...

Volatilities, traded volumes, and the hypothesis of price increments in derivative securities

Science.gov (United States)

Lim, Gyuchang; Kim, SooYong; Scalas, Enrico; Kim, Kyungsik

2007-08-01

A detrended fluctuation analysis (DFA) is applied to the statistics of Korean treasury bond (KTB) futures from which the logarithmic increments, volatilities, and traded volumes are estimated over a specific time lag. In this study, the logarithmic increment of futures prices has no long-memory property, while the volatility and the traded volume exhibit the existence of the long-memory property. To analyze and calculate whether the volatility clustering is due to a inherent higher-order correlation not detected by with the direct application of the DFA to logarithmic increments of KTB futures, it is of importance to shuffle the original tick data of future prices and to generate a geometric Brownian random walk with the same mean and standard deviation. It was found from a comparison of the three tick data that the higher-order correlation inherent in logarithmic increments leads to volatility clustering. Particularly, the result of the DFA on volatilities and traded volumes can be supported by the hypothesis of price changes.

Otolith development in larval and juvenile Schizothorax davidi: ontogeny and growth increment characteristics

Science.gov (United States)

Yan, Taiming; Hu, Jiaxiang; Cai, Yueping; Xiong, Sen; Yang, Shiyong; Wang, Xiongyan; He, Zhi

2017-09-01

Laboratory-reared Schizothorax davidi larvae and juveniles were examined to assess the formation and characteristics of David's schizothoracin otoliths. Otolith development was observed and their formation period was verified by monitoring larvae and juveniles of known age. The results revealed that lapilli and sagittae developed before hatching, and the first otolith increment was identified at 2 days post hatching in both. The shape of lapilli was relatively stable during development compared with that of sagittae; however, growth of four sagittae and lapilli areas was consistent, but the posterior area grew faster than the anterior area and the ventral surface grew faster than the dorsal surface. Similarly, the sum length of the radius of the anterior and posterior areas on sagittae and lapilli were linearly and binomially related to total fish length, respectively. Moreover, daily deposition rates were validated by monitoring knownage larvae and juveniles. The increase in lapilli width was 1.88±0.080 0 μm at the ninth increment, which reached a maximum and the decreased gradually toward the otolith edge, whereas that of sagittae increased more slowly. These results illustrate the developmental biology of S. davidi, which will aid in population conservation and fish stock management.

Software designs of image processing tasks with incremental refinement of computation.

Science.gov (United States)

Anastasia, Davide; Andreopoulos, Yiannis

2010-08-01

Software realizations of computationally-demanding image processing tasks (e.g., image transforms and convolution) do not currently provide graceful degradation when their clock-cycles budgets are reduced, e.g., when delay deadlines are imposed in a multitasking environment to meet throughput requirements. This is an important obstacle in the quest for full utilization of modern programmable platforms' capabilities since worst-case considerations must be in place for reasonable quality of results. In this paper, we propose (and make available online) platform-independent software designs performing bitplane-based computation combined with an incremental packing framework in order to realize block transforms, 2-D convolution and frame-by-frame block matching. The proposed framework realizes incremental computation: progressive processing of input-source increments improves the output quality monotonically. Comparisons with the equivalent nonincremental software realization of each algorithm reveal that, for the same precision of the result, the proposed approach can lead to comparable or faster execution, while it can be arbitrarily terminated and provide the result up to the computed precision. Application examples with region-of-interest based incremental computation, task scheduling per frame, and energy-distortion scalability verify that our proposal provides significant performance scalability with graceful degradation.

Incremental cost of implementing residual insecticide treatment with delthametrine on top of intensive routine Aedes aegypti control.

Science.gov (United States)

Baly, Alberto; Gonzalez, Karelia; Cabrera, Pedro; Popa, Julio C; Toledo, Maria E; Hernandez, Claudia; Montada, Domingo; Vanlerberghe, Veerle; Van der Stuyft, Patrick

2016-05-01

Information on the cost of implementing residual insecticide treatment (RIT) for Aedes control is scarce. We evaluated the incremental cost on top of intensive conventional routine activities of the Aedes control programme (ACP) in the city of Santiago de Cuba, Cuba. We conducted the cost analysis study in 2011-2012, from the perspective of the ACP. Data sources were bookkeeping records, activity registers of the Provincial ACP Centre and the accounts of an RIT implementation study in 21 clusters of on average four house blocks comprising 5180 premises. The annual cost of the routine ACP activities was 19.66 US$ per household. RIT applications in rounds at 4-month intervals covering, on average, 97.2% and using 8.5 g of delthametrine annually per household, cost 3.06 US$ per household per year. Delthametrine comprised 66.5% of this cost; the additional cost for deploying RIT comprised 15.6% of the total ACP routine cost and 27% of the cost related to routine adult stage Aedes control. The incremental cost of implementing RIT is high. It should be weighed against the incremental effect on the burden caused by the array of pathogens transmitted by Aedes. The cost could be reduced if the insecticide became cheaper, by limiting the number of yearly applications or by targeting transmission hot spots. © 2016 John Wiley & Sons Ltd.

Evidence combination for incremental decision-making processes

NARCIS (Netherlands)

Berrada, Ghita; van Keulen, Maurice; de Keijzer, Ander

The establishment of a medical diagnosis is an incremental process highly fraught with uncertainty. At each step of this painstaking process, it may be beneficial to be able to quantify the uncertainty linked to the diagnosis and steadily update the uncertainty estimation using available sources of

Incremental Nonnegative Matrix Factorization for Face Recognition

Directory of Open Access Journals (Sweden)

Wen-Sheng Chen

2008-01-01

Full Text Available Nonnegative matrix factorization (NMF is a promising approach for local feature extraction in face recognition tasks. However, there are two major drawbacks in almost all existing NMF-based methods. One shortcoming is that the computational cost is expensive for large matrix decomposition. The other is that it must conduct repetitive learning, when the training samples or classes are updated. To overcome these two limitations, this paper proposes a novel incremental nonnegative matrix factorization (INMF for face representation and recognition. The proposed INMF approach is based on a novel constraint criterion and our previous block strategy. It thus has some good properties, such as low computational complexity, sparse coefficient matrix. Also, the coefficient column vectors between different classes are orthogonal. In particular, it can be applied to incremental learning. Two face databases, namely FERET and CMU PIE face databases, are selected for evaluation. Compared with PCA and some state-of-the-art NMF-based methods, our INMF approach gives the best performance.

Apparatus for electrical-assisted incremental forming and process thereof

Science.gov (United States)

Roth, John; Cao, Jian

2018-04-24

A process and apparatus for forming a sheet metal component using an electric current passing through the component. The process can include providing an incremental forming machine, the machine having at least one arcuate tipped tool and at least electrode spaced a predetermined distance from the arcuate tipped tool. The machine is operable to perform a plurality of incremental deformations on the sheet metal component using the arcuate tipped tool. The machine is also operable to apply an electric direct current through the electrode into the sheet metal component at the predetermined distance from the arcuate tipped tool while the machine is forming the sheet metal component.

Existing School Buildings: Incremental Seismic Retrofit Opportunities.

Science.gov (United States)

Federal Emergency Management Agency, Washington, DC.

The intent of this document is to provide technical guidance to school district facility managers for linking specific incremental seismic retrofit opportunities to specific maintenance and capital improvement projects. The linkages are based on logical affinities, such as technical fit, location of the work within the building, cost saving…

Demonstration/Validation of Incremental Sampling at Two Diverse Military Ranges and Development of an Incremental Sampling Tool

Science.gov (United States)

2010-06-01

Sampling (MIS)? • Technique of combining many increments of soil from a number of points within exposure area • Developed by Enviro Stat (Trademarked...Demonstrating a reliable soil sampling strategy to accurately characterize contaminant concentrations in spatially extreme and heterogeneous...into a set of decision (exposure) units • One or several discrete or small- scale composite soil samples collected to represent each decision unit

Ethical leadership: meta-analytic evidence of criterion-related and incremental validity.

Science.gov (United States)

Ng, Thomas W H; Feldman, Daniel C

2015-05-01

This study examines the criterion-related and incremental validity of ethical leadership (EL) with meta-analytic data. Across 101 samples published over the last 15 years (N = 29,620), we observed that EL demonstrated acceptable criterion-related validity with variables that tap followers' job attitudes, job performance, and evaluations of their leaders. Further, followers' trust in the leader mediated the relationships of EL with job attitudes and performance. In terms of incremental validity, we found that EL significantly, albeit weakly in some cases, predicted task performance, citizenship behavior, and counterproductive work behavior-even after controlling for the effects of such variables as transformational leadership, use of contingent rewards, management by exception, interactional fairness, and destructive leadership. The article concludes with a discussion of ways to strengthen the incremental validity of EL. (PsycINFO Database Record (c) 2015 APA, all rights reserved).

Total Protein of Whole Saliva as a Biomarker of Anaerobic Threshold

Science.gov (United States)

Bortolini, Miguel Junior Sordi; De Agostini, Guilherme Gularte; Reis, Ismair Teodoro; Lamounier, Romeu Paulo Martins Silva; Blumberg, Jeffrey B.; Espindola, Foued Salmen

2009-01-01

Saliva provides a convenient and noninvasive matrix for assessing specific physiological parameters, including some biomarkers of exercise. We investigated whether the total protein concentration of whole saliva (TPWS) would reflect the anaerobic threshold during an incremental exercise test. After a warm-up period, 13 nonsmoking men performed a…

Incremental projection approach of regularization for inverse problems

Energy Technology Data Exchange (ETDEWEB)

Souopgui, Innocent, E-mail: innocent.souopgui@usm.edu [The University of Southern Mississippi, Department of Marine Science (United States); Ngodock, Hans E., E-mail: hans.ngodock@nrlssc.navy.mil [Naval Research Laboratory (United States); Vidard, Arthur, E-mail: arthur.vidard@imag.fr; Le Dimet, François-Xavier, E-mail: ledimet@imag.fr [Laboratoire Jean Kuntzmann (France)

2016-10-15

This paper presents an alternative approach to the regularized least squares solution of ill-posed inverse problems. Instead of solving a minimization problem with an objective function composed of a data term and a regularization term, the regularization information is used to define a projection onto a convex subspace of regularized candidate solutions. The objective function is modified to include the projection of each iterate in the place of the regularization. Numerical experiments based on the problem of motion estimation for geophysical fluid images, show the improvement of the proposed method compared with regularization methods. For the presented test case, the incremental projection method uses 7 times less computation time than the regularization method, to reach the same error target. Moreover, at convergence, the incremental projection is two order of magnitude more accurate than the regularization method.

Incremental Frequent Subgraph Mining on Large Evolving Graphs

KAUST Repository

Abdelhamid, Ehab; Canim, Mustafa; Sadoghi, Mohammad; Bhatta, Bishwaranjan; Chang, Yuan-Chi; Kalnis, Panos

2017-01-01

, such as social networks, utilize large evolving graphs. Mining these graphs using existing techniques is infeasible, due to the high computational cost. In this paper, we propose IncGM+, a fast incremental approach for continuous frequent subgraph mining problem

Parallel Algorithm for Incremental Betweenness Centrality on Large Graphs

KAUST Repository

Jamour, Fuad Tarek

2017-10-17

Betweenness centrality quantifies the importance of nodes in a graph in many applications, including network analysis, community detection and identification of influential users. Typically, graphs in such applications evolve over time. Thus, the computation of betweenness centrality should be performed incrementally. This is challenging because updating even a single edge may trigger the computation of all-pairs shortest paths in the entire graph. Existing approaches cannot scale to large graphs: they either require excessive memory (i.e., quadratic to the size of the input graph) or perform unnecessary computations rendering them prohibitively slow. We propose iCentral; a novel incremental algorithm for computing betweenness centrality in evolving graphs. We decompose the graph into biconnected components and prove that processing can be localized within the affected components. iCentral is the first algorithm to support incremental betweeness centrality computation within a graph component. This is done efficiently, in linear space; consequently, iCentral scales to large graphs. We demonstrate with real datasets that the serial implementation of iCentral is up to 3.7 times faster than existing serial methods. Our parallel implementation that scales to large graphs, is an order of magnitude faster than the state-of-the-art parallel algorithm, while using an order of magnitude less computational resources.

Using Analysis Increments (AI) to Estimate and Correct Systematic Errors in the Global Forecast System (GFS) Online

Science.gov (United States)

Bhargava, K.; Kalnay, E.; Carton, J.; Yang, F.

2017-12-01

Systematic forecast errors, arising from model deficiencies, form a significant portion of the total forecast error in weather prediction models like the Global Forecast System (GFS). While much effort has been expended to improve models, substantial model error remains. The aim here is to (i) estimate the model deficiencies in the GFS that lead to systematic forecast errors, (ii) implement an online correction (i.e., within the model) scheme to correct GFS following the methodology of Danforth et al. [2007] and Danforth and Kalnay [2008, GRL]. Analysis Increments represent the corrections that new observations make on, in this case, the 6-hr forecast in the analysis cycle. Model bias corrections are estimated from the time average of the analysis increments divided by 6-hr, assuming that initial model errors grow linearly and first ignoring the impact of observation bias. During 2012-2016, seasonal means of the 6-hr model bias are generally robust despite changes in model resolution and data assimilation systems, and their broad continental scales explain their insensitivity to model resolution. The daily bias dominates the sub-monthly analysis increments and consists primarily of diurnal and semidiurnal components, also requiring a low dimensional correction. Analysis increments in 2015 and 2016 are reduced over oceans, which is attributed to improvements in the specification of the SSTs. These results encourage application of online correction, as suggested by Danforth and Kalnay, for mean, seasonal and diurnal and semidiurnal model biases in GFS to reduce both systematic and random errors. As the error growth in the short-term is still linear, estimated model bias corrections can be added as a forcing term in the model tendency equation to correct online. Preliminary experiments with GFS, correcting temperature and specific humidity online show reduction in model bias in 6-hr forecast. This approach can then be used to guide and optimize the design of sub

Estimation of incremental reactivities for multiple day scenarios: an application to ethane and dimethyoxymethane

Science.gov (United States)

Stockwell, William R.; Geiger, Harald; Becker, Karl H.

Single-day scenarios are used to calculate incremental reactivities by definition (Carter, J. Air Waste Management Assoc. 44 (1994) 881-899.) but even unreactive organic compounds may have a non-negligible effect on ozone concentrations if multiple-day scenarios are considered. The concentration of unreactive compounds and their products may build up over a multiple-day period and the oxidation products may be highly reactive or highly unreactive affecting the overall incremental reactivity of the organic compound. We have developed a method for calculating incremental reactivities for multiple days based on a standard scenario for polluted European conditions. This method was used to estimate maximum incremental reactivities (MIR) and maximum ozone incremental reactivities (MOIR) for ethane and dimethyoxymethane for scenarios ranging from 1 to 6 days. It was found that the incremental reactivities increased as the length of the simulation period increased. The MIR of ethane increased faster than the value for dimethyoxymethane as the scenarios became longer. The MOIRs of ethane and dimethyoxymethane increased but the change was more modest for scenarios longer than 3 days. MOIRs of both volatile organic compounds were equal within the uncertainties of their chemical mechanisms by the 5 day scenario. These results show that dimethyoxymethane has an ozone forming potential on a per mass basis that is only somewhat greater than ethane if multiple-day scenarios are considered.

Lactate and ammonia concentration in blood and sweat during incremental cycle ergometer exercise

NARCIS (Netherlands)

Ament, W; Huizenga, [No Value; Mook, GA; Gips, CH; Verkerke, GJ

It is known that the concentrations of ammonia and lactate in blood increase during incremental exercise. Sweat also contains lactate and ammonia. The aim of the present study was to investigate the physiological response of lactate and ammonia in plasma and sweat during a stepwise incremental cycle

Potential stocks and increments of woody biomass in the European Union under different management and climate scenarios.

Science.gov (United States)

Kindermann, Georg E; Schörghuber, Stefan; Linkosalo, Tapio; Sanchez, Anabel; Rammer, Werner; Seidl, Rupert; Lexer, Manfred J

2013-02-01

Forests play an important role in the global carbon flow. They can store carbon and can also provide wood which can substitute other materials. In EU27 the standing biomass is steadily increasing. Increments and harvests seem to have reached a plateau between 2005 and 2010. One reason for reaching this plateau will be the circumstance that the forests are getting older. High ages have the advantage that they typical show high carbon concentration and the disadvantage that the increment rates are decreasing. It should be investigated how biomass stock, harvests and increments will develop under different climate scenarios and two management scenarios where one is forcing to store high biomass amounts in forests and the other tries to have high increment rates and much harvested wood. A management which is maximising standing biomass will raise the stem wood carbon stocks from 30 tC/ha to 50 tC/ha until 2100. A management which is maximising increments will lower the stock to 20 tC/ha until 2100. The estimates for the climate scenarios A1b, B1 and E1 are different but there is much more effect by the management target than by the climate scenario. By maximising increments the harvests are 0.4 tC/ha/year higher than in the management which maximises the standing biomass. The increments until 2040 are close together but around 2100 the increments when maximising standing biomass are approximately 50 % lower than those when maximising increments. Cold regions will benefit from the climate changes in the climate scenarios by showing higher increments. The results of this study suggest that forest management should maximise increments, not stocks to be more efficient in sense of climate change mitigation. This is true especially for regions which have already high carbon stocks in forests, what is the case in many regions in Europe. During the time span 2010-2100 the forests of EU27 will absorb additional 1750 million tC if they are managed to maximise increments compared

Generic model of a community-based microgrid integrating wind turbines, photovoltaics and CHP generations

International Nuclear Information System (INIS)

Ma, Xiandong; Wang, Yifei; Qin, Jianrong

2013-01-01

Highlights: ► Proposes a generic microgrid model comprising hybrid distributed generation units. ► Examines DG performance due to both environmental condition changes and electrical faults. ► Addresses island and grid connected modes of operation for DG units. ► We demonstrate the feasibility of the proposed residential microgrid system. - Abstract: Development and deployment of low-carbon energy technologies has been a national strategy of both the UK and China for a number of years, including the use of renewable generation technologies and the improvement of energy efficiency of operations and activities. The paper addresses several issues of generic importance to a residential microgrid system such as network modelling, advanced control and integration of intelligent monitoring techniques. The system, comprising representative distributed generation technologies of photovoltaics, wind turbines and combined heat and power, has been simulated by PSCAD/EMTDC under different operational scenarios. Studies include the effect of environmental condition changes, control systems and power electronics on wind turbines and PV cells, and the mixture of wind/solar/CHP energy generation under dominance of each technology. The performance and dynamics of the system are examined against symmetrical and asymmetrical electrical faults to seek an optimal isolation and restoration of the distributed generation unit from the connected grid system. Modelling these system interactions has demonstrated the feasibility of the proposed residential microgrid system

Techno-economic performance analysis of bio-oil based Fischer-Tropsch and CHP synthesis platform

International Nuclear Information System (INIS)

Ng, Kok Siew; Sadhukhan, Jhuma

2011-01-01

The techno-economic potential of the UK poplar wood and imported oil palm empty fruit bunch derived bio-oil integrated gasification and Fischer-Tropsch (BOIG-FT) systems for the generation of transportation fuels and combined heat and power (CHP) was investigated. The bio-oil was represented in terms of main chemical constituents, i.e. acetic acid, acetol and guaiacol. The compositional model of bio-oil was validated based on its performance through a gasification process. Given the availability of large scale gasification and FT technologies and logistic constraints in transporting biomass in large quantities, distributed bio-oil generations using biomass pyrolysis and centralised bio-oil processing in BOIG-FT system are technically more feasible. Heat integration heuristics and composite curve analysis were employed for once-through and full conversion configurations, and for a range of economies of scale, 1 MW, 675 MW and 1350 MW LHV of bio-oil. The economic competitiveness increases with increasing scale. A cost of production of FT liquids of 78.7 Euro/MWh was obtained based on 80.12 Euro/MWh of electricity, 75 Euro/t of bio-oil and 116.3 million Euro/y of annualised capital cost. -- Highlights: → Biomass to liquid process and gas to liquid process synthesis. → Biorefinery economic analysis. → Pyrolysis oil to biofuel. → Gasification and Fischer-Tropsch. → Process integration, pinch analysis and energy efficiency.

Local sharing of cogeneration energy through individually prioritized controls for increased on-site energy utilization

International Nuclear Information System (INIS)

Hirvonen, Janne; Kayo, Genku; Hasan, Ala; Sirén, Kai

2014-01-01

Highlights: • Sharing of surplus heat and electricity produced by CHP plants in different types of buildings. • Individually prioritized control of CHP plants with direct local sharing and minimal storage capacity. • Energy sharing reduced primary energy consumption by 1–9% with biogas. • Excess energy minimized by thermal tracking. - Abstract: All over the world, including Japan, there are targets to decrease building energy consumption and increase renewable energy utilization. Combined heat and power (CHP) plants increase energy efficiency and are becoming popular in Japan. CHP plants produce both heat and power simultaneously, but there is not always a need for both. A cluster of several different buildings can increase total efficiency and reduce primary energy (PE) consumption by sharing excess heat and electricity between neighboring buildings. If the generated energy comes from renewable sources, energy sharing makes it easier to reach the net zero energy balance. By adjusting CHP sizes and operation patterns, the wasted heat and primary energy consumption can be minimized. Energy sharing has been explored in situations with identical buildings and centrally administered energy systems before, but not with different building types with separate systems. In this study, a cluster of Japanese office and residential buildings were combined to allow heat and electricity sharing based on cogeneration, using individually prioritized control (IPC) systems. TRNSYS simulation was used to match energy generation with pregenerated demand profiles. Absorption cooling was utilized to increase the benefits of local heat generation. Different CHP operation modes and plant sizes were tested. The benefit of surplus energy sharing depends on the CHP capacities and the fuel type. When using biogas, larger CHP plants provided lower total primary energy consumption, in the most extreme case lowering it by 71%, compared to the conventional case. Using natural gas

Single Point Incremental Forming to increase material knowledge and production flexibility

Science.gov (United States)

Habraken, A. M.

2016-08-01

Nowadays, manufactured pieces can be divided into two groups: mass production and production of low volume number of parts. Within the second group (prototyping or small batch production), an emerging solution relies on Incremental Sheet Forming or ISF. ISF refers to processes where the plastic deformation occurs by repeated contact with a relatively small tool. More specifically, many publications over the past decade investigate Single Point Incremental Forming (SPIF) where the final shape is determined only by the tool movement. This manufacturing process is characterized by the forming of sheets by means of a CNC controlled generic tool stylus, with the sheets clamped by means of a non-workpiece-specific clamping system and in absence of a partial or a full die. The advantage is no tooling requirements and often enhanced formability, however it poses a challenge in term of process control and accuracy assurance. Note that the most commonly used materials in incremental forming are aluminum and steel alloys however other alloys are also used especially for medical industry applications, such as cobalt and chromium alloys, stainless steel and titanium alloys. Some scientists have applied incremental forming on PVC plates and other on sandwich panels composed of propylene with mild steel and aluminum metallic foams with aluminum sheet metal. Micro incremental forming of thin foils has also been developed. Starting from the scattering of the results of Finite Element (FE) simulations, when one tries to predict the tool force (see SPIF benchmark of 2014 Numisheet conference), we will see how SPIF and even micro SPIF (process applied on thin metallic sheet with a few grains within the thickness) allow investigating the material behavior. This lecture will focus on the identification of constitutive laws, on the SPIF forming mechanisms and formability as well as the failure mechanism. Different hypotheses have been proposed to explain SPIF formability, they will be

Single Point Incremental Forming to increase material knowledge and production flexibility

International Nuclear Information System (INIS)

Habraken, A.M.

2016-01-01

Nowadays, manufactured pieces can be divided into two groups: mass production and production of low volume number of parts. Within the second group (prototyping or small batch production), an emerging solution relies on Incremental Sheet Forming or ISF. ISF refers to processes where the plastic deformation occurs by repeated contact with a relatively small tool. More specifically, many publications over the past decade investigate Single Point Incremental Forming (SPIF) where the final shape is determined only by the tool movement. This manufacturing process is characterized by the forming of sheets by means of a CNC controlled generic tool stylus, with the sheets clamped by means of a non-workpiece-specific clamping system and in absence of a partial or a full die. The advantage is no tooling requirements and often enhanced formability, however it poses a challenge in term of process control and accuracy assurance. Note that the most commonly used materials in incremental forming are aluminum and steel alloys however other alloys are also used especially for medical industry applications, such as cobalt and chromium alloys, stainless steel and titanium alloys. Some scientists have applied incremental forming on PVC plates and other on sandwich panels composed of propylene with mild steel and aluminum metallic foams with aluminum sheet metal. Micro incremental forming of thin foils has also been developed. Starting from the scattering of the results of Finite Element (FE) simulations, when one tries to predict the tool force (see SPIF benchmark of 2014 Numisheet conference), we will see how SPIF and even micro SPIF (process applied on thin metallic sheet with a few grains within the thickness) allow investigating the material behavior. This lecture will focus on the identification of constitutive laws, on the SPIF forming mechanisms and formability as well as the failure mechanism. Different hypotheses have been proposed to explain SPIF formability, they will be

PCA/INCREMENT MEMORY interface for analog processors on-line with PC-XT/AT IBM

International Nuclear Information System (INIS)

Biri, S.; Buttsev, V.S.; Molnar, J.; Samojlov, V.N.

1989-01-01

The functional and operational descriptions on PCA/INCREMENT MEMORY interface are discussed. The following is solved with this unit: connection between the analogue signal processor and PC, nuclear spectrum acquisition up to 2 24 -1 counts/channel using increment or decrement method, data read/write from or to memory via data bus PC during the spectrum acquisition. Dual ported memory organization is 4096x24 bit, increment cycle time at 4.77 MHz system clock frequency is 1.05 μs. 6 refs.; 2 figs

Playing by the rules? Analysing incremental urban developments

NARCIS (Netherlands)

Karnenbeek, van Lilian; Janssen-Jansen, Leonie

2018-01-01

Current urban developments are often considered outdated and static, and the argument follows that they should become more adaptive. In this paper, we argue that existing urban development are already adaptive and incremental. Given this flexibility in urban development, understanding changes in the

Effects of endurance training on reduction of plasma glucose during high intensity constant and incremental speed tests in Wistar rats

Directory of Open Access Journals (Sweden)

P. Abreu

Full Text Available The aim of this research was to investigate the effects of endurance training on reduction of plasma glucose during high intensity constant and incremental speed tests in Wistar rats. We hypothesized that plasma glucose might be decreased in the exercised group during heavy (more intense exercise. Twenty-four 10-week-old male Wistar rats were randomly assigned to sedentary and exercised groups. The prescription of endurance exercise training intensity was determined as 60% of the maximum intensity reached at the incremental speed test. The animals were trained by running on a motorized treadmill, five days/week for a total period of 67 weeks. Plasma glucose during the constant speed test in the exercised group at 20 m/min was reduced at the 14th, 21st and 28th min compared to the sedentary group, as well at 25 m/min at the 21st and 28th min. Plasma glucose during the incremental speed test was decreased in the exercised group at the moment of exhaustion (48th min compared to the sedentary group (27th min. Endurance training positively modulates the mitochondrial activity and capacity of substrate oxidation in muscle and liver. Thus, in contrast to other studies on high load of exercise, the effects of endurance training on the decrease of plasma glucose during constant and incremental speed tests was significantly higher in exercised than in sedentary rats and associated with improved muscle and hepatic oxidative capacity, constituting an important non-pharmacological intervention tool for the prevention of insulin resistance, including type 2 diabetes mellitus.

A program for the numerical control of a pulse increment system

Energy Technology Data Exchange (ETDEWEB)

Gray, D.C.

1963-08-21

This report will describe the important features of the development of magnetic tapes for the numerical control of a pulse-increment system consisting of a modified Gorton lathe and its associated control unit developed by L. E. Foley of Equipment Development Service, Engineering Services, General Electric Co., Schenectady, N.Y. Included is a description of CUPID (Control and Utilization of Pulse Increment Devices), a FORTRAN program for the design of these tapes on the IBM 7090 computer, and instructions for its operation.

BMI and BMI SDS in childhood: annual increments and conditional change

OpenAIRE

Brannsether-Ellingsen, Bente; Eide, Geir Egil; Roelants, Mathieu; Bjerknes, Robert; Juliusson, Petur Benedikt

2016-01-01

Background: Early detection of abnormal weight gain in childhood may be important for preventive purposes. It is still debated which annual changes in BMI should warrant attention. Aim: To analyse 1-year increments of Body Mass Index (BMI) and standardised BMI (BMI SDS) in childhood and explore conditional change in BMI SDS as an alternative method to evaluate 1-year changes in BMI. Subjects and methods: The distributions of 1-year increments of BMI (kg/m2) and BMI SDS are summarised by...

Decoupled Simulation Method For Incremental Sheet Metal Forming

International Nuclear Information System (INIS)

Sebastiani, G.; Brosius, A.; Tekkaya, A. E.; Homberg, W.; Kleiner, M.

2007-01-01

Within the scope of this article a decoupling algorithm to reduce computing time in Finite Element Analyses of incremental forming processes will be investigated. Based on the given position of the small forming zone, the presented algorithm aims at separating a Finite Element Model in an elastic and an elasto-plastic deformation zone. Including the elastic response of the structure by means of model simplifications, the costly iteration in the elasto-plastic zone can be restricted to the small forming zone and to few supporting elements in order to reduce computation time. Since the forming zone moves along the specimen, an update of both, forming zone with elastic boundary and supporting structure, is needed after several increments.The presented paper discusses the algorithmic implementation of the approach and introduces several strategies to implement the denoted elastic boundary condition at the boundary of the plastic forming zone

Automobile sheet metal part production with incremental sheet forming

Directory of Open Access Journals (Sweden)

İsmail DURGUN

2016-02-01

Full Text Available Nowadays, effect of global warming is increasing drastically so it leads to increased interest on energy efficiency and sustainable production methods. As a result of adverse conditions, national and international project platforms, OEMs (Original Equipment Manufacturers, SMEs (Small and Mid-size Manufacturers perform many studies or improve existing methodologies in scope of advanced manufacturing techniques. In this study, advanced manufacturing and sustainable production method "Incremental Sheet Metal Forming (ISF" was used for sheet metal forming process. A vehicle fender was manufactured with or without die by using different toolpath strategies and die sets. At the end of the study, Results have been investigated under the influence of method and parameters used.Keywords: Template incremental sheet metal, Metal forming

Conservation of wildlife populations: factoring in incremental disturbance.

Science.gov (United States)

Stewart, Abbie; Komers, Petr E

2017-06-01

Progressive anthropogenic disturbance can alter ecosystem organization potentially causing shifts from one stable state to another. This potential for ecosystem shifts must be considered when establishing targets and objectives for conservation. We ask whether a predator-prey system response to incremental anthropogenic disturbance might shift along a disturbance gradient and, if it does, whether any disturbance thresholds are evident for this system. Development of linear corridors in forested areas increases wolf predation effectiveness, while high density of development provides a safe-haven for their prey. If wolves limit moose population growth, then wolves and moose should respond inversely to land cover disturbance. Using general linear model analysis, we test how the rate of change in moose ( Alces alces ) density and wolf ( Canis lupus ) harvest density are influenced by the rate of change in land cover and proportion of land cover disturbed within a 300,000 km 2 area in the boreal forest of Alberta, Canada. Using logistic regression, we test how the direction of change in moose density is influenced by measures of land cover change. In response to incremental land cover disturbance, moose declines occurred where 43% of land cover was disturbed and wolf density declined. Wolves and moose appeared to respond inversely to incremental disturbance with the balance between moose decline and wolf increase shifting at about 43% of land cover disturbed. Conservation decisions require quantification of disturbance rates and their relationships to predator-prey systems because ecosystem responses to anthropogenic disturbance shift across disturbance gradients.

Numerical simulation of pseudoelastic shape memory alloys using the large time increment method

Science.gov (United States)

Gu, Xiaojun; Zhang, Weihong; Zaki, Wael; Moumni, Ziad

2017-04-01

The paper presents a numerical implementation of the large time increment (LATIN) method for the simulation of shape memory alloys (SMAs) in the pseudoelastic range. The method was initially proposed as an alternative to the conventional incremental approach for the integration of nonlinear constitutive models. It is adapted here for the simulation of pseudoelastic SMA behavior using the Zaki-Moumni model and is shown to be especially useful in situations where the phase transformation process presents little or lack of hardening. In these situations, a slight stress variation in a load increment can result in large variations of strain and local state variables, which may lead to difficulties in numerical convergence. In contrast to the conventional incremental method, the LATIN method solve the global equilibrium and local consistency conditions sequentially for the entire loading path. The achieved solution must satisfy the conditions of static and kinematic admissibility and consistency simultaneously after several iterations. 3D numerical implementation is accomplished using an implicit algorithm and is then used for finite element simulation using the software Abaqus. Computational tests demonstrate the ability of this approach to simulate SMAs presenting flat phase transformation plateaus and subjected to complex loading cases, such as the quasi-static behavior of a stent structure. Some numerical results are contrasted to those obtained using step-by-step incremental integration.

Incremental net social benefit associated with using nuclear-fueled power plants

International Nuclear Information System (INIS)

Maoz, I.

1976-12-01

The incremental net social benefit (INSB) resulting from nuclear-fueled, rather than coal-fired, electric power generation is assessed. The INSB is defined as the difference between the 'incremental social benefit' (ISB)--caused by the cheaper technology of electric power generation, and the 'incremental social cost' (ISC)--associated with an increased power production, which is induced by cheaper technology. Section 2 focuses on the theoretical and empirical problems associated with the assessment of the long-run price elasticity of the demand for electricity, and the theoretical-econometric considerations that lead to the reasonable estimates of price elasticities of demand from those provided by recent empirical studies. Section 3 covers the theoretical and empirical difficulties associated with the construction of the long-run social marginal cost curves (LRSMC) of electricity. Sections 4 and 5 discuss the assessment methodology and provide numerical examples for the calculation of the INSB resulting from nuclear-fueled power generation

On the validity of the incremental approach to estimate the impact of cities on air quality

Science.gov (United States)

Thunis, Philippe

2018-01-01

The question of how much cities are the sources of their own air pollution is not only theoretical as it is critical to the design of effective strategies for urban air quality planning. In this work, we assess the validity of the commonly used incremental approach to estimate the likely impact of cities on their air pollution. With the incremental approach, the city impact (i.e. the concentration change generated by the city emissions) is estimated as the concentration difference between a rural background and an urban background location, also known as the urban increment. We show that the city impact is in reality made up of the urban increment and two additional components and consequently two assumptions need to be fulfilled for the urban increment to be representative of the urban impact. The first assumption is that the rural background location is not influenced by emissions from within the city whereas the second requires that background concentration levels, obtained with zero city emissions, are equal at both locations. Because the urban impact is not measurable, the SHERPA modelling approach, based on a full air quality modelling system, is used in this work to assess the validity of these assumptions for some European cities. Results indicate that for PM2.5, these two assumptions are far from being fulfilled for many large or medium city sizes. For this type of cities, urban increments are largely underestimating city impacts. Although results are in better agreement for NO2, similar issues are met. In many situations the incremental approach is therefore not an adequate estimate of the urban impact on air pollution. This poses issues in terms of interpretation when these increments are used to define strategic options in terms of air quality planning. We finally illustrate the interest of comparing modelled and measured increments to improve our confidence in the model results.

Ultra Clean 1.1MW High Efficiency Natural Gas Engine Powered System

Energy Technology Data Exchange (ETDEWEB)

Zurlo, James; Lueck, Steve

2011-08-31

Dresser, Inc. (GE Energy, Waukesha gas engines) will develop, test, demonstrate, and commercialize a 1.1 Megawatt (MW) natural gas fueled combined heat and power reciprocating engine powered package. This package will feature a total efficiency > 75% and ultra low CARB permitting emissions. Our modular design will cover the 1 – 6 MW size range, and this scalable technology can be used in both smaller and larger engine powered CHP packages. To further advance one of the key advantages of reciprocating engines, the engine, generator and CHP package will be optimized for low initial and operating costs. Dresser, Inc. will leverage the knowledge gained in the DOE - ARES program. Dresser, Inc. will work with commercial, regulatory, and government entities to help break down barriers to wider deployment of CHP. The outcome of this project will be a commercially successful 1.1 MW CHP package with high electrical and total efficiency that will significantly reduce emissions compared to the current central power plant paradigm. Principal objectives by phases for Budget Period 1 include: • Phase 1 – market study to determine optimum system performance, target first cost, lifecycle cost, and creation of a detailed product specification. • Phase 2 – Refinement of the Waukesha CHP system design concepts, identification of critical characteristics, initial evaluation of technical solutions, and risk mitigation plans. Background

Bipower variation for Gaussian processes with stationary increments

DEFF Research Database (Denmark)

Barndorff-Nielsen, Ole Eiler; Corcuera, José Manuel; Podolskij, Mark

2009-01-01

Convergence in probability and central limit laws of bipower variation for Gaussian processes with stationary increments and for integrals with respect to such processes are derived. The main tools of the proofs are some recent powerful techniques of Wiener/Itô/Malliavin calculus for establishing...

The National Institute of Education and Incremental Budgeting.

Science.gov (United States)

Hastings, Anne H.

1979-01-01

The National Institute of Education's (NIE) history demonstrates that the relevant criteria for characterizing budgeting as incremental are not the predictability and stability of appropriations but the conditions of complexity, limited information, multiple factors, and imperfect agreement on ends; NIE's appropriations were dominated by political…

Incremental Support Vector Machine Framework for Visual Sensor Networks

Directory of Open Access Journals (Sweden)

Yuichi Motai

2007-01-01

Full Text Available Motivated by the emerging requirements of surveillance networks, we present in this paper an incremental multiclassification support vector machine (SVM technique as a new framework for action classification based on real-time multivideo collected by homogeneous sites. The technique is based on an adaptation of least square SVM (LS-SVM formulation but extends beyond the static image-based learning of current SVM methodologies. In applying the technique, an initial supervised offline learning phase is followed by a visual behavior data acquisition and an online learning phase during which the cluster head performs an ensemble of model aggregations based on the sensor nodes inputs. The cluster head then selectively switches on designated sensor nodes for future incremental learning. Combining sensor data offers an improvement over single camera sensing especially when the latter has an occluded view of the target object. The optimization involved alleviates the burdens of power consumption and communication bandwidth requirements. The resulting misclassification error rate, the iterative error reduction rate of the proposed incremental learning, and the decision fusion technique prove its validity when applied to visual sensor networks. Furthermore, the enabled online learning allows an adaptive domain knowledge insertion and offers the advantage of reducing both the model training time and the information storage requirements of the overall system which makes it even more attractive for distributed sensor networks communication.

Two-Point Incremental Forming with Partial Die: Theory and Experimentation

Science.gov (United States)

Silva, M. B.; Martins, P. A. F.

2013-04-01

This paper proposes a new level of understanding of two-point incremental forming (TPIF) with partial die by means of a combined theoretical and experimental investigation. The theoretical developments include an innovative extension of the analytical model for rotational symmetric single point incremental forming (SPIF), originally developed by the authors, to address the influence of the major operating parameters of TPIF and to successfully explain the differences in formability between SPIF and TPIF. The experimental work comprised the mechanical characterization of the material and the determination of its formability limits at necking and fracture by means of circle grid analysis and benchmark incremental sheet forming tests. Results show the adequacy of the proposed analytical model to handle the deformation mechanics of SPIF and TPIF with partial die and demonstrate that neck formation is suppressed in TPIF, so that traditional forming limit curves are inapplicable to describe failure and must be replaced by fracture forming limits derived from ductile damage mechanics. The overall geometric accuracy of sheet metal parts produced by TPIF with partial die is found to be better than that of parts fabricated by SPIF due to smaller elastic recovery upon unloading.

A comparative study of velocity increment generation between the rigid body and flexible models of MMET

Energy Technology Data Exchange (ETDEWEB)

Ismail, Norilmi Amilia, E-mail: aenorilmi@usm.my [School of Aerospace Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Pulau Pinang (Malaysia)

2016-02-01

The motorized momentum exchange tether (MMET) is capable of generating useful velocity increments through spin–orbit coupling. This study presents a comparative study of the velocity increments between the rigid body and flexible models of MMET. The equations of motions of both models in the time domain are transformed into a function of true anomaly. The equations of motion are integrated, and the responses in terms of the velocity increment of the rigid body and flexible models are compared and analysed. Results show that the initial conditions, eccentricity, and flexibility of the tether have significant effects on the velocity increments of the tether.

Evolving effective incremental SAT solvers with GP

OpenAIRE

Bader, Mohamed; Poli, R.

2008-01-01

Hyper-Heuristics could simply be defined as heuristics to choose other heuristics, and it is a way of combining existing heuristics to generate new ones. In a Hyper-Heuristic framework, the framework is used for evolving effective incremental (Inc*) solvers for SAT. We test the evolved heuristics (IncHH) against other known local search heuristics on a variety of benchmark SAT problems.

Real Time Implementation of Incremental Fuzzy Logic Controller for Gas Pipeline Corrosion Control

Directory of Open Access Journals (Sweden)

Gopalakrishnan Jayapalan

2014-01-01

Full Text Available A robust virtual instrumentation based fuzzy incremental corrosion controller is presented to protect metallic gas pipelines. Controller output depends on error and change in error of the controlled variable. For corrosion control purpose pipe to soil potential is considered as process variable. The proposed fuzzy incremental controller is designed using a very simple control rule base and the most natural and unbiased membership functions. The proposed scheme is tested for a wide range of pipe to soil potential control. Performance comparison between the conventional proportional integral type and proposed fuzzy incremental controller is made in terms of several performance criteria such as peak overshoot, settling time, and rise time. Result shows that the proposed controller outperforms its conventional counterpart in each case. Designed controller can be taken in automode without waiting for initial polarization to stabilize. Initial startup curve of proportional integral controller and fuzzy incremental controller is reported. This controller can be used to protect any metallic structures such as pipelines, tanks, concrete structures, ship, and offshore structures.

Minimizing System Modification in an Incremental Design Approach

DEFF Research Database (Denmark)

Pop, Paul; Eles, Petru; Pop, Traian

2001-01-01

In this paper we present an approach to mapping and scheduling of distributed embedded systems for hard real-time applications, aiming at minimizing the system modification cost. We consider an incremental design process that starts from an already existing sys-tem running a set of applications. We...

EFFECT OF COST INCREMENT DISTRIBUTION PATTERNS ON THE PERFORMANCE OF JIT SUPPLY CHAIN

Directory of Open Access Journals (Sweden)

Ayu Bidiawati J.R

2008-01-01

Full Text Available Cost is an important consideration in supply chain (SC optimisation. This is due to emphasis placed on cost reduction in order to optimise profit. Some researchers use cost as one of their performance measures and others propose ways of accurately calculating cost. As product moves across SC, the product cost also increases. This paper studied the effect of cost increment distribution patterns on the performance of a JIT Supply Chain. In particular, it is necessary to know if inventory allocation across SC needs to be modified to accommodate different cost increment distribution patterns. It was found that funnel is still the best card distribution pattern for JIT-SC regardless the cost increment distribution patterns used.

BMI and BMI SDS in childhood: annual increments and conditional change.

Science.gov (United States)

Brannsether, Bente; Eide, Geir Egil; Roelants, Mathieu; Bjerknes, Robert; Júlíusson, Pétur Benedikt

2017-02-01

Background Early detection of abnormal weight gain in childhood may be important for preventive purposes. It is still debated which annual changes in BMI should warrant attention. Aim To analyse 1-year increments of Body Mass Index (BMI) and standardised BMI (BMI SDS) in childhood and explore conditional change in BMI SDS as an alternative method to evaluate 1-year changes in BMI. Subjects and methods The distributions of 1-year increments of BMI (kg/m 2 ) and BMI SDS are summarised by percentiles. Differences according to sex, age, height, weight, initial BMI and weight status on the BMI and BMI SDS increments were assessed with multiple linear regression. Conditional change in BMI SDS was based on the correlation between annual BMI measurements converted to SDS. Results BMI increments depended significantly on sex, height, weight and initial BMI. Changes in BMI SDS depended significantly only on the initial BMI SDS. The distribution of conditional change in BMI SDS using a two-correlation model was close to normal (mean = 0.11, SD = 1.02, n = 1167), with 3.2% (2.3-4.4%) of the observations below -2 SD and 2.8% (2.0-4.0%) above +2 SD. Conclusion Conditional change in BMI SDS can be used to detect unexpected large changes in BMI SDS. Although this method requires the use of a computer, it may be clinically useful to detect aberrant weight development.

Relating annual increments of the endangered Blanding's turtle plastron growth to climate.

Science.gov (United States)

Richard, Monik G; Laroque, Colin P; Herman, Thomas B

2014-05-01

This research is the first published study to report a relationship between climate variables and plastron growth increments of turtles, in this case the endangered Nova Scotia Blanding's turtle (Emydoidea blandingii). We used techniques and software common to the discipline of dendrochronology to successfully cross-date our growth increment data series, to detrend and average our series of 80 immature Blanding's turtles into one common chronology, and to seek correlations between the chronology and environmental temperature and precipitation variables. Our cross-dated chronology had a series intercorrelation of 0.441 (above 99% confidence interval), an average mean sensitivity of 0.293, and an average unfiltered autocorrelation of 0.377. Our master chronology represented increments from 1975 to 2007 (33 years), with index values ranging from a low of 0.688 in 2006 to a high of 1.303 in 1977. Univariate climate response function analysis on mean monthly air temperature and precipitation values revealed a positive correlation with the previous year's May temperature and current year's August temperature; a negative correlation with the previous year's October temperature; and no significant correlation with precipitation. These techniques for determining growth increment response to environmental variables should be applicable to other turtle species and merit further exploration.

Incremental Validity of the Trait Emotional Intelligence Questionnaire-Short Form (TEIQue-SF).

Science.gov (United States)

Siegling, A B; Vesely, Ashley K; Petrides, K V; Saklofske, Donald H

2015-01-01

This study examined the incremental validity of the adult short form of the Trait Emotional Intelligence Questionnaire (TEIQue-SF) in predicting 7 construct-relevant criteria beyond the variance explained by the Five-factor model and coping strategies. Additionally, the relative contributions of the questionnaire's 4 subscales were assessed. Two samples of Canadian university students completed the TEIQue-SF, along with measures of the Big Five, coping strategies (Sample 1 only), and emotion-laden criteria. The TEIQue-SF showed consistent incremental effects beyond the Big Five or the Big Five and coping strategies, predicting all 7 criteria examined across the 2 samples. Furthermore, 2 of the 4 TEIQue-SF subscales accounted for the measure's incremental validity. Although the findings provide good support for the validity and utility of the TEIQue-SF, directions for further research are emphasized.

Incremental cost of nosocomial bacteremia according to the focus of infection and antibiotic sensitivity of the causative microorganism in a university hospital.

Science.gov (United States)

Riu, Marta; Chiarello, Pietro; Terradas, Roser; Sala, Maria; Garcia-Alzorriz, Enric; Castells, Xavier; Grau, Santiago; Cots, Francesc

2017-04-01

To estimate the incremental cost of nosocomial bacteremia according to the causative focus and classified by the antibiotic sensitivity of the microorganism.Patients admitted to Hospital del Mar in Barcelona from 2005 to 2012 were included. We analyzed the total hospital costs of patients with nosocomial bacteremia caused by microorganisms with a high prevalence and, often, with multidrug-resistance. A control group was defined by selecting patients without bacteremia in the same diagnosis-related group.Our hospital has a cost accounting system (full-costing) that uses activity-based criteria to estimate per-patient costs. A logistic regression was fitted to estimate the probability of developing bacteremia (propensity score) and was used for propensity-score matching adjustment. This propensity score was included in an econometric model to adjust the incremental cost of patients with bacteremia with differentiation of the causative focus and antibiotic sensitivity.The mean incremental cost was estimated at &OV0556;15,526. The lowest incremental cost corresponded to bacteremia caused by multidrug-sensitive urinary infection (&OV0556;6786) and the highest to primary or unknown sources of bacteremia caused by multidrug-resistant microorganisms (&OV0556;29,186).This is one of the first analyses to include all episodes of bacteremia produced during hospital stays in a single study. The study included accurate information about the focus and antibiotic sensitivity of the causative organism and actual hospital costs. It provides information that could be useful to improve, establish, and prioritize prevention strategies for nosocomial infections.

Learning in Different Modes: The Interaction Between Incremental and Radical Change

DEFF Research Database (Denmark)

Petersen, Anders Hedegaard; Boer, Harry; Gertsen, Frank

2004-01-01

The objective of the study presented in this article is to contribute to the development of theory on continuous innovation, i.e. the combination of operationally effective exploitation and strategically flexible exploration. A longitudinal case study is presented of the interaction between...... incremental and radical change in Danish company, observed through the lens of organizational learning. The radical change process is described in five phases, each of which had its own effects on incremental change initiatives in the company. The research identified four factors explaining these effects, all...

Incremental Approach to the Technology of Test Design for Industrial Projects

Directory of Open Access Journals (Sweden)

P. D. Drobintsev

2014-01-01

Full Text Available The paper presents an approach to effort reduction in developing test suites for industrial software products based on the incremental technology. The main problems to be solved by the incremental technology are full automation design of test scenarios and significant reducing of test explosion. The proposed approach provides solutions to the mentioned problems through joint co-working of a designer and a customer, through the integration of symbolic verification with the automatic generation of test suites; through the usage of an efficient technology with the toolset VRS/TAT.

Two models of minimalist, incremental syntactic analysis.

Science.gov (United States)

Stabler, Edward P

2013-07-01

Minimalist grammars (MGs) and multiple context-free grammars (MCFGs) are weakly equivalent in the sense that they define the same languages, a large mildly context-sensitive class that properly includes context-free languages. But in addition, for each MG, there is an MCFG which is strongly equivalent in the sense that it defines the same language with isomorphic derivations. However, the structure-building rules of MGs but not MCFGs are defined in a way that generalizes across categories. Consequently, MGs can be exponentially more succinct than their MCFG equivalents, and this difference shows in parsing models too. An incremental, top-down beam parser for MGs is defined here, sound and complete for all MGs, and hence also capable of parsing all MCFG languages. But since the parser represents its grammar transparently, the relative succinctness of MGs is again evident. Although the determinants of MG structure are narrowly and discretely defined, probabilistic influences from a much broader domain can influence even the earliest analytic steps, allowing frequency and context effects to come early and from almost anywhere, as expected in incremental models. Copyright © 2013 Cognitive Science Society, Inc.

Towards Reliable and Energy-Efficient Incremental Cooperative Communication for Wireless Body Area Networks.

Science.gov (United States)

Yousaf, Sidrah; Javaid, Nadeem; Qasim, Umar; Alrajeh, Nabil; Khan, Zahoor Ali; Ahmed, Mansoor

2016-02-24

In this study, we analyse incremental cooperative communication for wireless body area networks (WBANs) with different numbers of relays. Energy efficiency (EE) and the packet error rate (PER) are investigated for different schemes. We propose a new cooperative communication scheme with three-stage relaying and compare it to existing schemes. Our proposed scheme provides reliable communication with less PER at the cost of surplus energy consumption. Analytical expressions for the EE of the proposed three-stage cooperative communication scheme are also derived, taking into account the effect of PER. Later on, the proposed three-stage incremental cooperation is implemented in a network layer protocol; enhanced incremental cooperative critical data transmission in emergencies for static WBANs (EInCo-CEStat). Extensive simulations are conducted to validate the proposed scheme. Results of incremental relay-based cooperative communication protocols are compared to two existing cooperative routing protocols: cooperative critical data transmission in emergencies for static WBANs (Co-CEStat) and InCo-CEStat. It is observed from the simulation results that incremental relay-based cooperation is more energy efficient than the existing conventional cooperation protocol, Co-CEStat. The results also reveal that EInCo-CEStat proves to be more reliable with less PER and higher throughput than both of the counterpart protocols. However, InCo-CEStat has less throughput with a greater stability period and network lifetime. Due to the availability of more redundant links, EInCo-CEStat achieves a reduced packet drop rate at the cost of increased energy consumption.

Increments in insulin sensitivity during intensive treatment are closely correlated with decrements in glucocorticoid receptor mRNA in skeletal muscle from patients with Type II diabetes

DEFF Research Database (Denmark)

Vestergaard, H; Bratholm, P; Christensen, N J

2001-01-01

decreased significantly after intensive insulin treatment. A close correlation was found between increments in glucose uptake during intensive treatment and decrements in skeletal muscle total GCR mRNA (r=0.95, Pmultiple regression analysis), and between glucose uptake and alpha/alpha 2 GCR m RNA...

Motor unit firing frequency of lower limb muscles during an incremental slide board skating test.

Science.gov (United States)

Piucco, Tatiane; Bini, Rodrigo; Sakaguchi, Masanori; Diefenthaeler, Fernando; Stefanyshyn, Darren

2017-11-01

This study investigated how the combination of workload and fatigue affected the frequency components of muscle activation and possible recruitment priority of motor units during skating to exhaustion. Ten male competitive speed skaters performed an incremental maximal test on a slide board. Activation of six muscles from the right leg was recorded throughout the test. A time-frequency analysis was performed to compute overall, high, and low frequency bands from the whole signal at 10, 40, 70, and 90% of total test time. Overall activation increased for all muscles throughout the test (p  0.80). There was an increase in low frequency (90 vs. 10%, p = 0.035, ES = 1.06) and a decrease in high frequency (90 vs. 10%, p = 0.009, ES = 1.38, and 90 vs. 40%, p = 0.025, ES = 1.12) components of gluteus maximus. Strong correlations were found between the maximal cadence and vastus lateralis, gluteus maximus and gluteus medius activation at the end of the test. In conclusion, the incremental skating test lead to an increase in activation of lower limb muscles, but only gluteus maximus was sensitive to changes in frequency components, probably caused by a pronounced fatigue.

Effect of multiple forming tools on geometrical and mechanical properties in incremental sheet forming

Science.gov (United States)

Wernicke, S.; Dang, T.; Gies, S.; Tekkaya, A. E.

2018-05-01

The tendency to a higher variety of products requires economical manufacturing processes suitable for the production of prototypes and small batches. In the case of complex hollow-shaped parts, single point incremental forming (SPIF) represents a highly flexible process. The flexibility of this process comes along with a very long process time. To decrease the process time, a new incremental forming approach with multiple forming tools is investigated. The influence of two incremental forming tools on the resulting mechanical and geometrical component properties compared to SPIF is presented. Sheets made of EN AW-1050A were formed to frustums of a pyramid using different tool-path strategies. Furthermore, several variations of the tool-path strategy are analyzed. A time saving between 40% and 60% was observed depending on the tool-path and the radii of the forming tools while the mechanical properties remained unchanged. This knowledge can increase the cost efficiency of incremental forming processes.

Application of combined heat and power in Malaysia Industrial Sector

International Nuclear Information System (INIS)

Zaredah Hashim; Faridah Mohd Taha

2010-01-01

Malaysia is still working on continuing its economic growth especially in the industrial sector in order to achieve vision 2020. The rapid industrialization process has caused increment in the energy demand, which simultaneously increases carbon dioxide (CO 2 ) emissions. Energy efficient technologies are strongly needed for reducing the energy requirement and to avoid the depleting of energy resources. This project focused on the application of integrated resource planning (IRP) in industrial sector using Combined Heat and Power (CHP), as a strategy for Demand Side Management (DSM). This approach is another way for meeting near and future energy requirement in Malaysia's industrial sector. Two scenarios which are Business As Usual (BAU) and CHP were developed using End Use Model EUM), to forecast the energy demand and CO 2 emission in Malaysia's industries. The effectiveness of the proposed method is then simulated using Long Range Energy Alternative Planning System (LEAP) software and Comparative Model for Projects of Engineering Economics and Energy Environmental Development (COMPEED) analysis. Evaluations were based on the potential of energy saving and CO 2 reduction. Scope of research was limited to pulp and paper industrial sub sector. The research data were extracted from Energy Audit Reports conducted by Malaysia Energy Center (PTM). An engineering calculation was demonstrated. Two designs of CHP applications for the pulp and paper industrial sector are according to heating and electricity sizing. It was found that the most energy efficient and CO 2 reduction for Malaysia's industrial sector is the CHP based on heating requirement. The method was found to be able of save fuel and GHG emission compared to the reference case. (author)

Parallel Algorithm for Incremental Betweenness Centrality on Large Graphs

KAUST Repository

Jamour, Fuad Tarek; Skiadopoulos, Spiros; Kalnis, Panos

2017-01-01

: they either require excessive memory (i.e., quadratic to the size of the input graph) or perform unnecessary computations rendering them prohibitively slow. We propose iCentral; a novel incremental algorithm for computing betweenness centrality in evolving

Incremental principal component pursuit for video background modeling

Science.gov (United States)

Rodriquez-Valderrama, Paul A.; Wohlberg, Brendt

2017-03-14

An incremental Principal Component Pursuit (PCP) algorithm for video background modeling that is able to process one frame at a time while adapting to changes in background, with a computational complexity that allows for real-time processing, having a low memory footprint and is robust to translational and rotational jitter.

Geometry of finite deformations and time-incremental analysis

Czech Academy of Sciences Publication Activity Database

Fiala, Zdeněk

2016-01-01

Roč. 81, May (2016), s. 230-244 ISSN 0020-7462 Institutional support: RVO:68378297 Keywords : solid mechanics * finite deformations * time-incremental analysis * Lagrangian system * evolution equation of Lie type Subject RIV: BE - Theoretical Physics Impact factor: 2.074, year: 2016 http://www.sciencedirect.com/science/article/pii/S0020746216000330

Incremental View Maintenance for Deductive Graph Databases Using Generalized Discrimination Networks

Directory of Open Access Journals (Sweden)

Thomas Beyhl

2016-12-01

Full Text Available Nowadays, graph databases are employed when relationships between entities are in the scope of database queries to avoid performance-critical join operations of relational databases. Graph queries are used to query and modify graphs stored in graph databases. Graph queries employ graph pattern matching that is NP-complete for subgraph isomorphism. Graph database views can be employed that keep ready answers in terms of precalculated graph pattern matches for often stated and complex graph queries to increase query performance. However, such graph database views must be kept consistent with the graphs stored in the graph database. In this paper, we describe how to use incremental graph pattern matching as technique for maintaining graph database views. We present an incremental maintenance algorithm for graph database views, which works for imperatively and declaratively specified graph queries. The evaluation shows that our maintenance algorithm scales when the number of nodes and edges stored in the graph database increases. Furthermore, our evaluation shows that our approach can outperform existing approaches for the incremental maintenance of graph query results.

Final Safety Analysis Report (FSAR) for Building 332, Increment III

Energy Technology Data Exchange (ETDEWEB)

Odell, B. N.; Toy, Jr., A. J.

1977-08-31

This Final Safety Analysis Report (FSAR) supplements the Preliminary Safety Analysis Report (PSAR), dated January 18, 1974, for Building 332, Increment III of the Plutonium Materials Engineering Facility located at the Lawrence Livermore Laboratory (LLL). The FSAR, in conjunction with the PSAR, shows that the completed increment provides facilities for safely conducting the operations as described. These documents satisfy the requirements of ERDA Manual Appendix 6101, Annex C, dated April 8, 1971. The format and content of this FSAR complies with the basic requirements of the letter of request from ERDA San to LLL, dated March 10, 1972. Included as appendices in support of th FSAR are the Building 332 Operational Safety Procedure and the LLL Disaster Control Plan.

Health level seven interoperability strategy: big data, incrementally structured.

Science.gov (United States)

Dolin, R H; Rogers, B; Jaffe, C

2015-01-01

Describe how the HL7 Clinical Document Architecture (CDA), a foundational standard in US Meaningful Use, contributes to a "big data, incrementally structured" interoperability strategy, whereby data structured incrementally gets large amounts of data flowing faster. We present cases showing how this approach is leveraged for big data analysis. To support the assertion that semi-structured narrative in CDA format can be a useful adjunct in an overall big data analytic approach, we present two case studies. The first assesses an organization's ability to generate clinical quality reports using coded data alone vs. coded data supplemented by CDA narrative. The second leverages CDA to construct a network model for referral management, from which additional observations can be gleaned. The first case shows that coded data supplemented by CDA narrative resulted in significant variances in calculated performance scores. In the second case, we found that the constructed network model enables the identification of differences in patient characteristics among different referral work flows. The CDA approach goes after data indirectly, by focusing first on the flow of narrative, which is then incrementally structured. A quantitative assessment of whether this approach will lead to a greater flow of data and ultimately a greater flow of structured data vs. other approaches is planned as a future exercise. Along with growing adoption of CDA, we are now seeing the big data community explore the standard, particularly given its potential to supply analytic en- gines with volumes of data previously not possible.

A fast implementation of the incremental backprojection algorithms for parallel beam geometries

International Nuclear Information System (INIS)

Chen, C.M.; Wang, C.Y.; Cho, Z.H.

1996-01-01

Filtered-backprojection algorithms are the most widely used approaches for reconstruction of computed tomographic (CT) images, such as X-ray CT and positron emission tomographic (PET) images. The Incremental backprojection algorithm is a fast backprojection approach based on restructuring the Shepp and Logan algorithm. By exploiting interdependency (position and values) of adjacent pixels, the Incremental algorithm requires only O(N) and O(N 2 ) multiplications in contrast to O(N 2 ) and O(N 3 ) multiplications for the Shepp and Logan algorithm in two-dimensional (2-D) and three-dimensional (3-D) backprojections, respectively, for each view, where N is the size of the image in each dimension. In addition, it may reduce the number of additions for each pixel computation. The improvement achieved by the Incremental algorithm in practice was not, however, as significant as expected. One of the main reasons is due to inevitably visiting pixels outside the beam in the searching flow scheme originally developed for the Incremental algorithm. To optimize implementation of the Incremental algorithm, an efficient scheme, namely, coded searching flow scheme, is proposed in this paper to minimize the overhead caused by searching for all pixels in a beam. The key idea of this scheme is to encode the searching flow for all pixels inside each beam. While backprojecting, all pixels may be visited without any overhead due to using the coded searching flow as the a priori information. The proposed coded searching flow scheme has been implemented on a Sun Sparc 10 and a Sun Sparc 20 workstations. The implementation results show that the proposed scheme is 1.45--2.0 times faster than the original searching flow scheme for most cases tested

Increment and mortality in a virgin Douglas-fir forest.

Science.gov (United States)

Robert W. Steele; Norman P. Worthington

1955-01-01

Is there any basis to the forester's rule of thumb that virgin forests eventually reach an equilibrium where increment and mortality approximately balance? Are we wasting potential timber volume by failing to salvage mortality in old-growth stands?

Studying effect of heating plant parameters on performances of a geothermal-fuelled series cogeneration plant based on Organic Rankine Cycle

International Nuclear Information System (INIS)

Habka, Muhsen; Ajib, Salman

2014-01-01

Highlights: • We analyzed performances of a series ORC–CHP plant versus the heating plant parameters. • ORC–CHP power is destructed when raising the heat demand or the return temperature. • Only the high supply temperatures of the heating plant affect negatively the performances. • Reducing the return temperature optimizes both the energetic and exergetic criteria. • Increasing the heat demand improves the exergetic efficiency of the total CHP system. - Abstract: The present work aims to analyze the performance characteristics of the series Combined Heat and Power (CHP) system based on Organic Rankine Cycle (ORC) under influence of the heating plant parameters without considering the chemistry of the geothermal water considered as heat source. For evaluation, energetic and exergetic criteria along with the heat transfer capacities have been determined, and also the working fluid R134a has been used. The results showed that increasing the heat demand or the return temperature and only the high supply temperatures lead to destruct the net power generated by the ORC–CHP system. While, influence of the last parameters on the total exergy efficiency and losses is different; whereas raising the heat demands optimizes these exergetic indicators, variation of the supply temperature leads to an optimum for these performances. Since increasing the return temperature has purely negative impacts on all exergetic and energetic criteria, the latter can be improved by reducing this temperature with attention to the heat transfer capacities. Thus, reduction of the return temperature about 5 °C lowers the exhausted stream losses by app. 25% and enhances the power generation by app. 52% and the total exergy efficiency by 9%

System incremental cost calculations using the participation factor load-flow formulation

International Nuclear Information System (INIS)

Meisel, J.

1993-01-01

The load-flow problem is reformulated such that the use of a slack-bus generator is included only as a special case. This reformulation, known as the participation factor load-flow, includes a total mismatch variable and a defined participation vector, which, in general, distributes this mismatch to all system buses. The slack-bus constraint can still be obtained by defining a particular participation vector. In using the participation factor load-flow in the transpose Jacobian approach to the economic optimal dispatch problem, the paper shows that the value of the system-λ can be controlled such that this value represents the minimal incremental change in generation costs per unit change in system total demand with this demand distributed according to the specified participation vector. Methods using the conventional B-coefficient loss formulas or slack-bus load-flows give system-λ values whereby the unit change in demand must be placed on a fictitious single load-bus or on the slack-bus, respectively. Having a system-λ value which more accurately represents a proposed energy interchange between interconnected systems is very important in developing valid costs for each system. An extensive 28-bus, 8-generator system is included to illustrate these results

A System to Derive Optimal Tree Diameter Increment Models from the Eastwide Forest Inventory Data Base (EFIDB)

Science.gov (United States)

Don C. Bragg

2002-01-01

This article is an introduction to the computer software used by the Potential Relative Increment (PRI) approach to optimal tree diameter growth modeling. These DOS programs extract qualified tree and plot data from the Eastwide Forest Inventory Data Base (EFIDB), calculate relative tree increment, sort for the highest relative increments by diameter class, and...

The economic burden of diabetes to French national health insurance: a new cost-of-illness method based on a combined medicalized and incremental approach.

Science.gov (United States)

de Lagasnerie, Grégoire; Aguadé, Anne-Sophie; Denis, Pierre; Fagot-Campagna, Anne; Gastaldi-Menager, Christelle

2018-03-01

A better understanding of the economic burden of diabetes constitutes a major public health challenge in order to design new ways to curb diabetes health care expenditure. The aim of this study was to develop a new cost-of-illness method in order to assess the specific and nonspecific costs of diabetes from a public payer perspective. Using medical and administrative data from the major French national health insurance system covering about 59 million individuals in 2012, we identified people with diabetes and then estimated the economic burden of diabetes. Various methods were used: (a) global cost of patients with diabetes, (b) cost of treatment directly related to diabetes (i.e., 'medicalized approach'), (c) incremental regression-based approach, (d) incremental matched-control approach, and (e) a novel combination of the 'medicalized approach' and the 'incremental matched-control' approach. We identified 3 million individuals with diabetes (5% of the population). The total expenditure of this population amounted to €19 billion, representing 15% of total expenditure reimbursed to the entire population. Of the total expenditure, €10 billion (52%) was considered to be attributable to diabetes care: €2.3 billion (23% of €10 billion) was directly attributable, and €7.7 billion was attributable to additional reimbursed expenditure indirectly related to diabetes (77%). Inpatient care represented the major part of the expenditure attributable to diabetes care (22%) together with drugs (20%) and medical auxiliaries (15%). Antidiabetic drugs represented an expenditure of about €1.1 billion, accounting for 49% of all diabetes-specific expenditure. This study shows the economic impact of the assumption concerning definition of costs on evaluation of the economic burden of diabetes. The proposed new cost-of-illness method provides specific insight for policy-makers to enhance diabetes management and assess the opportunity costs of diabetes complications

Microbiological Contamination at Workplaces in a Combined Heat and Power (CHP Station Processing Plant Biomass

Directory of Open Access Journals (Sweden)

Justyna Szulc

2017-01-01

Full Text Available The aim of the study was to evaluate the microbial contamination at a plant biomass processing thermal power station (CHP. We found 2.42 × 103 CFU/m3 of bacteria and 1.37 × 104 CFU/m3 of fungi in the air; 2.30 × 107 CFU/g of bacteria and 4.46 × 105 CFU/g of fungi in the biomass; and 1.61 × 102 CFU/cm2 bacteria and 2.39 × 101 CFU/cm2 fungi in filtering facepiece respirators (FFRs. Using culture methods, we found 8 genera of mesophilic bacteria and 7 of fungi in the air; 10 genera each of bacteria and fungi in the biomass; and 2 and 5, respectively, on the FFRs. Metagenomic analysis (Illumina MiSeq revealed the presence of 46 bacterial and 5 fungal genera on the FFRs, including potential pathogens Candida tropicalis, Escherichia coli, Prevotella sp., Aspergillus sp., Penicillium sp.. The ability of microorganisms to create a biofilm on the FFRs was confirmed using scanning electron microscopy (SEM. We also identified secondary metabolites in the biomass and FFRs, including fumigaclavines, quinocitrinines, sterigmatocistin, and 3-nitropropionic acid, which may be toxic to humans. Due to the presence of potential pathogens and mycotoxins, the level of microbiological contamination at workplaces in CHPs should be monitored.

Annual increments, specific gravity and energy of Eucalyptus grandis by gamma-ray attenuation technique

International Nuclear Information System (INIS)

Rezende, M.A.; Guerrini, I.A.; Ferraz, E.S.B.

1990-01-01

Specific gravity annual increments in volume, mass and energy of Eucalyptus grandis at thirteen years of age were made taking into account measurements of the calorific value for wood. It was observed that the calorific value for wood decrease slightly, while the specific gravity increase significantly with age. The so-called culmination age for the Annual Volume Increment was determined to be around fourth year of growth while for the Annual Mass and Energy Increment was around the eighty year. These results show that a tree in a particular age may not have a significant growth in volume, yet one is mass and energy. (author)

Stem analysis program (GOAP for evaluating of increment and growth data at individual tree

Directory of Open Access Journals (Sweden)

Gafura Aylak Özdemir

2016-07-01

Full Text Available Stem analysis is a method evaluating in a detailed way data of increment and growth of individual tree at the past periods and widely used in various forestry disciplines. Untreated data of stem analysis consist of annual ring count and measurement procedures performed on cross sections taken from individual tree by section method. The evaluation of obtained this untreated data takes quite some time. Thus, a computer software was developed in this study to quickly and efficiently perform stem analysis. This computer software developed to evaluate untreated data of stem analysis as numerical and graphical was programmed as macro by utilizing Visual Basic for Application feature of MS Excel 2013 program currently the most widely used. In developed this computer software, growth height model is formed from two different approaches, individual tree volume depending on section method, cross-sectional area, increments of diameter, height and volume, volume increment percent and stem form factor at breast height are calculated depending on desired period lengths. This calculated values are given as table. Development of diameter, height, volume, increments of these variables, volume increment percent and stem form factor at breast height according to periodic age are given as chart. Stem model showing development of diameter, height and shape of individual tree in the past periods also can be taken from computer software as chart.

Incremental exercise test performance with and without a respiratory ...

African Journals Online (AJOL)

Incremental exercise test performance with and without a respiratory gas collection system. ... PROMOTING ACCESS TO AFRICAN RESEARCH ... Industrial- type mask wear is thought to impair exercise performance through increased respiratory dead space, flow ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

Operating Experiences with a Small-scale CHP Pilot Plant based on a 35 kWel Hermetic Four Cylinder Stirling Engine for Biomass Fuels

DEFF Research Database (Denmark)

Biedermann, F.; Carlsen, Henrik; Schoech, M.

2003-01-01

Within the scope of the RD&D project presented a small-scale CHP plant with a hermetic four cylinder Stirling engine for biomass fuels was developed and optimised in cooperation with the Technical University of Denmark, MAWERA Holzfeuerungsanlagen GesmbH, an Austrian biomass furnace and boiler...... exchanger of the Stirling engine, of the air preheater and of the entire combustion system. Furthermore, the optimisation of the pneumatic cleaning system to reduce ash deposition in the hot heat exchanger is of great relevance....... manufacturer, and BIOS BIOENERGIESYSTEME GmbH, an Austrian development and engineering company. Based on the technology developed, a pilot plant was designed and erected in Austria. The nominal electric power output of the plant is 35 kWel and the nominal thermal output amounts to approx. 220 kWth. The plant...

A COMPARATIVE STUDY OF PREEMPTIVE USE OF 0.2% ROPIVACAINE AND 0.125% BUPIVACAINE ALONG WITH FENTANYL AND FENTANYL INCREMENTS TO PROVIDE POSTOPERATIVE EPIDURAL ANALGESIA UP TO 24 HOURS

Directory of Open Access Journals (Sweden)

Chiranji Lal Khedia

2016-06-01

Full Text Available BACKGROUND AND OBJECTIVES The present study was carried out to compare duration of analgesia, haemodynamic changes (Systolic and Diastolic Blood Pressure, Pulse Rate, Respiratory Rate, total incremental doses of epidural fentanyl required to maintain VAS 3 up to 24 hours in each group and total required incremental fentanyl doses were compared between both the groups. Once the data were collected from all the patients, they were compared using, chi-square test, two sample t-test. The p-value was calculated and P <0.05 was considered statistically significant. RESULTS The duration of analgesia was more with Group BF (245+17.58 min. than Group RF (217.6+22.41 min., thus it is concluded that difference in duration of analgesia was statistically significant between the groups (P<0.05. In this study, it was noticed that patients of Group RF required much more incremental doses of epidural fentanyl (218+31.88 μg to maintain VAS<3 up to 24 hours than group BF (170+32.27 μg, and difference was statistically significant (P<0.05. Haemodynamic parameters like SBP, DBP, HR and RR were comparable in both the groups. Hypotension and bradycardia were noted in two patients of group BF. CONCLUSION Duration of analgesia was longer and comparatively better in group BF and less incremental doses were required to maintain VAS <3 up to 24 hours as compared to group RF, but haemodynamic stability was more in group RF as compared to group BF.

Generation of Referring Expressions: Assessing the Incremental Algorithm

Science.gov (United States)

van Deemter, Kees; Gatt, Albert; van der Sluis, Ielka; Power, Richard

2012-01-01

A substantial amount of recent work in natural language generation has focused on the generation of "one-shot" referring expressions whose only aim is to identify a target referent. Dale and Reiter's Incremental Algorithm (IA) is often thought to be the best algorithm for maximizing the similarity to referring expressions produced by people. We…

Incremental exposure facilitates adaptation to sensory rearrangement. [vestibular stimulation patterns

Science.gov (United States)

Lackner, J. R.; Lobovits, D. N.

1978-01-01

Visual-target pointing experiments were performed on 24 adult volunteers in order to compare the relative effectiveness of incremental (stepwise) and single-step exposure conditions on adaptation to visual rearrangement. The differences between the preexposure and postexposure scores served as an index of the adaptation elicited during the exposure period. It is found that both single-step and stepwise exposure to visual rearrangement elicit compensatory changes in sensorimotor coordination. However, stepwise exposure, when compared to single-step exposur in terms of the average magnitude of visual displacement over the exposure period, clearly enhances the rate of adaptation. It seems possible that the enhancement of adaptation to unusual patterns of sensory stimulation produced by incremental exposure reflects a general principle of sensorimotor function.

Weighted tunable clustering in local-world networks with increment behavior

International Nuclear Information System (INIS)

Ma, Ying-Hong; Li, Huijia; Zhang, Xiao-Dong

2010-01-01

Since some realistic networks are influenced not only by increment behavior but also by the tunable clustering mechanism with new nodes to be added to networks, it is interesting to characterize the model for those actual networks. In this paper, a weighted local-world model, which incorporates increment behavior and the tunable clustering mechanism, is proposed and its properties are investigated, such as degree distribution and clustering coefficient. Numerical simulations are fitted to the model and also display good right-skewed scale-free properties. Furthermore, the correlation of vertices in our model is studied which shows the assortative property. The epidemic spreading process by weighted transmission rate on the model shows that the tunable clustering behavior has a great impact on the epidemic dynamic

On kinematical minimum principles for rates and increments in plasticity

International Nuclear Information System (INIS)

Zouain, N.

1984-01-01

The optimization approach for elastoplastic analysis is discussed showing that some minimum principles related to numerical methods can be derived by means of duality and penalization procedures. Three minimum principles for velocity and plastic multiplier rate fields are presented in the framework of perfect plasticity. The first one is the classical Greenberg formulation. The second one, due to Capurso, is developed here with different motivation, and modified by penalization of constraints so as to arrive at a third principle for rates. The counterparts of these optimization formulations in terms of discrete increments of displacements of displacements and plastic multipliers are discussed. The third one of these minimum principles for finite increments is recognized to be closely related to Maier's formulation of holonomic plasticity. (Author) [pt

Variance-optimal hedging for processes with stationary independent increments

DEFF Research Database (Denmark)

Hubalek, Friedrich; Kallsen, J.; Krawczyk, L.

We determine the variance-optimal hedge when the logarithm of the underlying price follows a process with stationary independent increments in discrete or continuous time. Although the general solution to this problem is known as backward recursion or backward stochastic differential equation, we...

FDTD Stability: Critical Time Increment

Directory of Open Access Journals (Sweden)

Z. Skvor

2003-06-01

Full Text Available A new approach suitable for determination of the maximal stable timeincrement for the Finite-Difference Time-Domain (FDTD algorithm incommon curvilinear coordinates, for general mesh shapes and certaintypes of boundaries is presented. The maximal time incrementcorresponds to a characteristic value of a Helmholz equation that issolved by a finite-difference (FD method. If this method uses exactlythe same discretization as the given FDTD method (same mesh, boundaryconditions, order of precision etc., the maximal stable time incrementis obtained from the highest characteristic value. The FD system issolved by an iterative method, which uses only slightly alteredoriginal FDTD formulae. The Courant condition yields a stable timeincrement, but in certain cases the maximum increment is slightlygreater [2].

Incremental cryptography and security of public hash functions ...

African Journals Online (AJOL)

An investigation of incremental algorithms for crytographic functions was initiated. The problem, for collision-free hashing, is to design a scheme for which there exists an efficient “update” algorithm: this algorithm is given the hash function H, the hash h = H(M) of message M and the “replacement request” (j, m), and outputs ...

Product Quality Modelling Based on Incremental Support Vector Machine

International Nuclear Information System (INIS)

Wang, J; Zhang, W; Qin, B; Shi, W

2012-01-01

Incremental Support vector machine (ISVM) is a new learning method developed in recent years based on the foundations of statistical learning theory. It is suitable for the problem of sequentially arriving field data and has been widely used for product quality prediction and production process optimization. However, the traditional ISVM learning does not consider the quality of the incremental data which may contain noise and redundant data; it will affect the learning speed and accuracy to a great extent. In order to improve SVM training speed and accuracy, a modified incremental support vector machine (MISVM) is proposed in this paper. Firstly, the margin vectors are extracted according to the Karush-Kuhn-Tucker (KKT) condition; then the distance from the margin vectors to the final decision hyperplane is calculated to evaluate the importance of margin vectors, where the margin vectors are removed while their distance exceed the specified value; finally, the original SVs and remaining margin vectors are used to update the SVM. The proposed MISVM can not only eliminate the unimportant samples such as noise samples, but also can preserve the important samples. The MISVM has been experimented on two public data and one field data of zinc coating weight in strip hot-dip galvanizing, and the results shows that the proposed method can improve the prediction accuracy and the training speed effectively. Furthermore, it can provide the necessary decision supports and analysis tools for auto control of product quality, and also can extend to other process industries, such as chemical process and manufacturing process.

First UHF Implementation of the Incremental Scheme for Open-Shell Systems.

Science.gov (United States)

Anacker, Tony; Tew, David P; Friedrich, Joachim

2016-01-12

The incremental scheme makes it possible to compute CCSD(T) correlation energies to high accuracy for large systems. We present the first extension of this fully automated black-box approach to open-shell systems using an Unrestricted Hartree-Fock (UHF) wave function, extending the efficient domain-specific basis set approach to handle open-shell references. We test our approach on a set of organic and metal organic structures and molecular clusters and demonstrate standard deviations from canonical CCSD(T) values of only 1.35 kJ/mol using a triple ζ basis set. We find that the incremental scheme is significantly more cost-effective than the canonical implementation even for relatively small systems and that the ease of parallelization makes it possible to perform high-level calculations on large systems in a few hours on inexpensive computers. We show that the approximations that make our approach widely applicable are significantly smaller than both the basis set incompleteness error and the intrinsic error of the CCSD(T) method, and we further demonstrate that incremental energies can be reliably used in extrapolation schemes to obtain near complete basis set limit CCSD(T) reaction energies for large systems.

Pornographic image recognition and filtering using incremental learning in compressed domain

Science.gov (United States)

Zhang, Jing; Wang, Chao; Zhuo, Li; Geng, Wenhao

2015-11-01

With the rapid development and popularity of the network, the openness, anonymity, and interactivity of networks have led to the spread and proliferation of pornographic images on the Internet, which have done great harm to adolescents' physical and mental health. With the establishment of image compression standards, pornographic images are mainly stored with compressed formats. Therefore, how to efficiently filter pornographic images is one of the challenging issues for information security. A pornographic image recognition and filtering method in the compressed domain is proposed by using incremental learning, which includes the following steps: (1) low-resolution (LR) images are first reconstructed from the compressed stream of pornographic images, (2) visual words are created from the LR image to represent the pornographic image, and (3) incremental learning is adopted to continuously adjust the classification rules to recognize the new pornographic image samples after the covering algorithm is utilized to train and recognize the visual words in order to build the initial classification model of pornographic images. The experimental results show that the proposed pornographic image recognition method using incremental learning has a higher recognition rate as well as costing less recognition time in the compressed domain.

National Accounts Energy Alliance : Field test and verification of CHP components and systems

Energy Technology Data Exchange (ETDEWEB)

Sweetser, R. [Exergy Partners Corporation, Herndon, VA (United States)

2003-07-01

Exergy is a consulting firm which specializes in capitalizing on opportunities that result from the nexus of utility deregulation and global climate change in both the construction and energy industries. The firm offers assistance in technical business and market planning, product development and high impact marketing and technology transfer programs. The author discussed National Accounts Energy Alliance (NAEA) program on distributed energy resources (DER) and identified some advantageous areas such as homeland security (less possible terrorist targets to be protected), food safety (protection of food supply and delivery system), reliability, power quality, energy density, grid congestion and energy price. In the future, an essential role in moderating energy prices for commercial buildings will probably be played by distributed generation (DG) and combined heat and power (CHP). The technical merits of these technologies is being investigated by national accounts and utilities partnering with non-profit organizations, the United States Department of Energy (US DOE), state governments and industry. In that light, in 2001 an Alliance program was developed, which allows investors to broaden their knowledge from the application and verification of Advanced Energy Technologies. This program was the result of a synergy between the American Gas Foundation and the Gas Technology Institute (GTI), and it assists investors with their strategic planning. It was proven that a customer-led Energy Technology Test and Verification Program (TA and VP) could be cost-effective and successful. The NAEA activities in five locations were reviewed and discussed. They were: (1) Russell Development, Portland, Oregon; (2) A and P-Waldbaums, Hauppage, New York; (3) HEB, Southern, Texas; (4) Cinemark, Plano, Texas; and McDonald's, Tampa, Florida. 4 tabs., figs.

A design of LED adaptive dimming lighting system based on incremental PID controller

Science.gov (United States)

He, Xiangyan; Xiao, Zexin; He, Shaojia

2010-11-01

As a new generation energy-saving lighting source, LED is applied widely in various technology and industry fields. The requirement of its adaptive lighting technology is more and more rigorous, especially in the automatic on-line detecting system. In this paper, a closed loop feedback LED adaptive dimming lighting system based on incremental PID controller is designed, which consists of MEGA16 chip as a Micro-controller Unit (MCU), the ambient light sensor BH1750 chip with Inter-Integrated Circuit (I2C), and constant-current driving circuit. A given value of light intensity required for the on-line detecting environment need to be saved to the register of MCU. The optical intensity, detected by BH1750 chip in real time, is converted to digital signal by AD converter of the BH1750 chip, and then transmitted to MEGA16 chip through I2C serial bus. Since the variation law of light intensity in the on-line detecting environment is usually not easy to be established, incremental Proportional-Integral-Differential (PID) algorithm is applied in this system. Control variable obtained by the incremental PID determines duty cycle of Pulse-Width Modulation (PWM). Consequently, LED's forward current is adjusted by PWM, and the luminous intensity of the detection environment is stabilized by self-adaptation. The coefficients of incremental PID are obtained respectively after experiments. Compared with the traditional LED dimming system, it has advantages of anti-interference, simple construction, fast response, and high stability by the use of incremental PID algorithm and BH1750 chip with I2C serial bus. Therefore, it is suitable for the adaptive on-line detecting applications.

The concept of system for chips production need to work demo CHP plant in company 'AGROSAVA' from Šimanovci

Directory of Open Access Journals (Sweden)

Dedić Aleksandar Đ.

2014-01-01

Full Text Available In this paper according to the calculation of chips productivity needs for gasification in the demo CHP plant for co-generation: electricity and heat, chippers were analyzed due to: the type of mobility, running for chipping and the method of delivering chips to temporary yard. The plant was planned to generate electricity power up to 200kWelec. First, in consideration were taken the chippers with medium capacity, which mainly served for chipping brushwood and leaves that remain after harvest plantations on mostly flat terrain and parks. Later, the comparative characteristics of the world's three largest manufacturers of machinery for the production of wood chips significantly larger amounts (up to 30m3/h were given. These chippers were particularly suitable for the higher density of crops and stationed yard, in which brushwood would be brought and chip. At the end, the types of convective dryers were analyzed that could be successfully used for drying wood chips (drum and pneumatic dryer and based on the calculation proposed the types of dryers that were available in the local market.

A practical approach to assess leg muscle oxygenation during ramp-incremental cycle ergometry in heart failure

Directory of Open Access Journals (Sweden)

A.C. Barroco

2017-10-01

Full Text Available Heart failure is characterized by the inability of the cardiovascular system to maintain oxygen (O2 delivery (i.e., muscle blood flow in non-hypoxemic patients to meet O2 demands. The resulting increase in fractional O2 extraction can be non-invasively tracked by deoxygenated hemoglobin concentration (deoxi-Hb as measured by near-infrared spectroscopy (NIRS. We aimed to establish a simplified approach to extract deoxi-Hb-based indices of impaired muscle O2 delivery during rapidly-incrementing exercise in heart failure. We continuously probed the right vastus lateralis muscle with continuous-wave NIRS during a ramp-incremental cardiopulmonary exercise test in 10 patients (left ventricular ejection fraction <35% and 10 age-matched healthy males. Deoxi-Hb is reported as % of total response (onset to peak exercise in relation to work rate. Patients showed lower maximum exercise capacity and O2 uptake-work rate than controls (P<0.05. The deoxi-Hb response profile as a function of work rate was S-shaped in all subjects, i.e., it presented three distinct phases. Increased muscle deoxygenation in patients compared to controls was demonstrated by: i a steeper mid-exercise deoxi-Hb-work rate slope (2.2±1.3 vs 1.0±0.3% peak/W, respectively; P<0.05, and ii late-exercise increase in deoxi-Hb, which contrasted with stable or decreasing deoxi-Hb in all controls. Steeper deoxi-Hb-work rate slope was associated with lower peak work rate in patients (r=–0.73; P=0.01. This simplified approach to deoxi-Hb interpretation might prove useful in clinical settings to quantify impairments in O2 delivery by NIRS during ramp-incremental exercise in individual heart failure patients.

Incremental rate of prefrontal oxygenation determines performance speed during cognitive Stroop test: the effect of ageing.

Science.gov (United States)

Endo, Kana; Liang, Nan; Idesako, Mitsuhiro; Ishii, Kei; Matsukawa, Kanji

2018-02-19

Cognitive function declines with age. The underlying mechanisms responsible for the deterioration of cognitive performance, however, remain poorly understood. We hypothesized that an incremental rate of prefrontal oxygenation during a cognitive Stroop test decreases in progress of ageing, resulting in a slowdown of cognitive performance. To test this hypothesis, we identified, using multichannel near-infrared spectroscopy, the characteristics of the oxygenated-hemoglobin concentration (Oxy-Hb) responses of the prefrontal cortex to both incongruent Stroop and congruent word-reading test. Spatial distributions of the significant changes in the three components (initial slope, peak amplitude, and area under the curve) of the Oxy-Hb response were compared between young and elderly subjects. The Stroop interference time (as a difference in total periods for executing Stroop and word-reading test, respectively) approximately doubled in elderly as compared to young subjects. The Oxy-Hb in the rostrolateral, but not caudal, prefrontal cortex increased during the Stroop test in both age groups. The initial slope of the Oxy-Hb response, rather than the peak and area under the curve, had a strong correlation with cognitive performance speed. Taken together, it is likely that the incremental rate of prefrontal oxygenation may decrease in progress of ageing, resulting in a decline in cognitive performance.

Incremental Learning of Perceptual Categories for Open-Domain Sketch Recognition

National Research Council Canada - National Science Library

Lovett, Andrew; Dehghani, Morteza; Forbus, Kenneth

2007-01-01

.... This paper describes an incremental learning technique for opendomain recognition. Our system builds generalizations for categories of objects based upon previous sketches of those objects and uses those generalizations to classify new sketches...

Incremental learning for automated knowledge capture

Energy Technology Data Exchange (ETDEWEB)

Benz, Zachary O. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Basilico, Justin Derrick [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Davis, Warren Leon [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dixon, Kevin R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Brian S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Martin, Nathaniel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wendt, Jeremy Daniel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2013-12-01

People responding to high-consequence national-security situations need tools to help them make the right decision quickly. The dynamic, time-critical, and ever-changing nature of these situations, especially those involving an adversary, require models of decision support that can dynamically react as a situation unfolds and changes. Automated knowledge capture is a key part of creating individualized models of decision making in many situations because it has been demonstrated as a very robust way to populate computational models of cognition. However, existing automated knowledge capture techniques only populate a knowledge model with data prior to its use, after which the knowledge model is static and unchanging. In contrast, humans, including our national-security adversaries, continually learn, adapt, and create new knowledge as they make decisions and witness their effect. This artificial dichotomy between creation and use exists because the majority of automated knowledge capture techniques are based on traditional batch machine-learning and statistical algorithms. These algorithms are primarily designed to optimize the accuracy of their predictions and only secondarily, if at all, concerned with issues such as speed, memory use, or ability to be incrementally updated. Thus, when new data arrives, batch algorithms used for automated knowledge capture currently require significant recomputation, frequently from scratch, which makes them ill suited for use in dynamic, timecritical, high-consequence decision making environments. In this work we seek to explore and expand upon the capabilities of dynamic, incremental models that can adapt to an ever-changing feature space.

A cannabigerol-rich Cannabis sativa extract, devoid of [INCREMENT]9-tetrahydrocannabinol, elicits hyperphagia in rats.

Science.gov (United States)

Brierley, Daniel I; Samuels, James; Duncan, Marnie; Whalley, Benjamin J; Williams, Claire M

2017-06-01

Nonpsychoactive phytocannabinoids (pCBs) from Cannabis sativa may represent novel therapeutic options for cachexia because of their pleiotropic pharmacological activities, including appetite stimulation. We have recently shown that purified cannabigerol (CBG) is a novel appetite stimulant in rats. As standardized extracts from Cannabis chemotypes dominant in one pCB [botanical drug substances (BDSs)] often show greater efficacy and/or potency than purified pCBs, we investigated the effects of a CBG-rich BDS, devoid of psychoactive [INCREMENT]-tetrahydrocannabinol, on feeding behaviour. Following a 2 h prefeed satiation procedure, 16 male Lister-hooded rats were administered CBG-BDS (at 30-240 mg/kg) or vehicle. Food intake, meal pattern microstructure and locomotor activity were recorded over 2 h. The total food intake was increased by 120 and 240 mg/kg CBG-BDS (1.53 and 1.36 g, respectively, vs. 0.56 g in vehicle-treated animals). Latency to feeding onset was dose dependently decreased at all doses, and 120 and 240 mg/kg doses increased both the number of meals consumed and the cumulative size of the first two meals. No significant effect was observed on ambulatory activity or rearing behaviour. CBG-BDS is a novel appetite stimulant, which may have greater potency than purified CBG, despite the absence of [INCREMENT]-tetrahydrocannabinol in the extract.

Revisiting the fundamentals of single point incremental forming by

DEFF Research Database (Denmark)

Silva, Beatriz; Skjødt, Martin; Martins, Paulo A.F.

2008-01-01

Knowledge of the physics behind the fracture of material at the transition between the inclined wall and the corner radius of the sheet is of great importance for understanding the fundamentals of single point incremental forming (SPIF). How the material fractures, what is the state of strain...

Will Incremental Hemodialysis Preserve Residual Function and Improve Patient Survival?

Science.gov (United States)

Davenport, Andrew

2015-01-01

The progressive loss of residual renal function in peritoneal dialysis patients is associated with increased mortality. It has been suggested that incremental dialysis may help preserve residual renal function and improve patient survival. Residual renal function depends upon both patient related and dialysis associated factors. Maintaining patients in an over-hydrated state may be associated with better preservation of residual renal function but any benefit comes with a significant risk of cardiovascular consequences. Notably, it is only observational studies that have reported an association between dialysis patient survival and residual renal function; causality has not been established for dialysis patient survival. The tenuous connections between residual renal function and outcomes and between incremental hemodialysis and residual renal function should temper our enthusiasm for interventions in this area. PMID:25385441

Spatial distance effects on incremental semantic interpretation of abstract sentences: evidence from eye tracking.

Science.gov (United States)

Guerra, Ernesto; Knoeferle, Pia

2014-12-01

A large body of evidence has shown that visual context information can rapidly modulate language comprehension for concrete sentences and when it is mediated by a referential or a lexical-semantic link. What has not yet been examined is whether visual context can also modulate comprehension of abstract sentences incrementally when it is neither referenced by, nor lexically associated with, the sentence. Three eye-tracking reading experiments examined the effects of spatial distance between words (Experiment 1) and objects (Experiment 2 and 3) on participants' reading times for sentences that convey similarity or difference between two abstract nouns (e.g., 'Peace and war are certainly different...'). Before reading the sentence, participants inspected a visual context with two playing cards that moved either far apart or close together. In Experiment 1, the cards turned and showed the first two nouns of the sentence (e.g., 'peace', 'war'). In Experiments 2 and 3, they turned but remained blank. Participants' reading times at the adjective (Experiment 1: first-pass reading time; Experiment 2: total times) and at the second noun phrase (Experiment 3: first-pass times) were faster for sentences that expressed similarity when the preceding words/objects were close together (vs. far apart) and for sentences that expressed dissimilarity when the preceding words/objects were far apart (vs. close together). Thus, spatial distance between words or entirely unrelated objects can rapidly and incrementally modulate the semantic interpretation of abstract sentences. Copyright © 2014 Elsevier B.V. All rights reserved.

Object class hierarchy for an incremental hypertext editor

Directory of Open Access Journals (Sweden)

A. Colesnicov

1995-02-01

Full Text Available The object class hierarchy design is considered due to a hypertext editor implementation. The following basic classes were selected: the editor's coordinate system, the memory manager, the text buffer executing basic editing operations, the inherited hypertext buffer, the edit window, the multi-window shell. Special hypertext editing features, the incremental hypertext creation support and further generalizations are discussed.

Incremental Learning of Skill Collections based on Intrinsic Motivation

Directory of Open Access Journals (Sweden)

Jan Hendrik Metzen

2013-07-01

Full Text Available Life-long learning of reusable, versatile skills is a key prerequisite forembodied agents that act in a complex, dynamic environment and are faced withdifferent tasks over their lifetime. We address the question of how an agentcan learn useful skills efficiently during a developmental period,i.e., when no task is imposed on him and no external reward signal is provided.Learning of skills in a developmental period needs to be incremental andself-motivated. We propose a new incremental, task-independent skill discoveryapproach that is suited for continuous domains. Furthermore, the agent learnsspecific skills based on intrinsic motivation mechanisms thatdetermine on which skills learning is focused at a given point in time. Weevaluate the approach in a reinforcement learning setup in two continuousdomains with complex dynamics. We show that an intrinsically motivated, skilllearning agent outperforms an agent which learns task solutions from scratch.Furthermore, we compare different intrinsic motivation mechanisms and howefficiently they make use of the agent's developmental period.

Efficient incremental relaying for packet transmission over fading channels

KAUST Repository

Fareed, Muhammad Mehboob

2014-07-01

In this paper, we propose a novel relaying scheme for packet transmission over fading channels, which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from the destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission suffers deep fading. We calculate the packet error rate for the proposed efficient incremental relaying (EIR) scheme with both amplify and forward and decode and forward relaying. We compare the performance of the EIR scheme with the threshold-based incremental relaying (TIR) scheme. It is shown that the efficiency of the TIR scheme is better for lower values of the threshold. However, the efficiency of the TIR scheme for higher values of threshold is outperformed by the EIR. In addition, three new threshold-based adaptive EIR are devised to further improve the efficiency of the EIR scheme. We calculate the packet error rate and the efficiency of these new schemes to provide the analytical insight. © 2014 IEEE.

Table incremental slow injection CE-CT in lung cancer

International Nuclear Information System (INIS)

Yoshida, Shoji; Maeda, Tomoho; Morita, Masaru

1988-01-01

The purpose of this study is to evaluate tumor enhancement in lung cancer under the table incremental study with slow injection of contrast media. The early serial 8 sliced images during the slow injection (1.5 ml/sec) of contrant media were obtained. Following the early images, delayed 8 same sliced images were taken in 2 minutes later. Chacteristic enhanced patterns of the primary cancer and metastatic mediastinal lymphnode were recognized in this study. Enhancement of the primary lesion was classified in 4 patterns, irregular geographic pattern, heterogeneous pattern, homogeneous pattern and rim-enhanced pattern. In mediastinal metastatic lymphadenopathy, three enhanced patterns were obtained, heterogeneous, homogeneous and ring enhanced pattern. Some characteristic enhancement patterns according to the histopathological finding of the lung cancer were obtained. With using this incremental slow injection CE-CT, precise information about the relationship between lung cancer and adjacent mediastinal structure, and obvious staining patterns of the tumor and mediastinal lymphnode were recognized. (author)

Broad Learning System: An Effective and Efficient Incremental Learning System Without the Need for Deep Architecture.

Science.gov (United States)

Chen, C L Philip; Liu, Zhulin

2018-01-01

Broad Learning System (BLS) that aims to offer an alternative way of learning in deep structure is proposed in this paper. Deep structure and learning suffer from a time-consuming training process because of a large number of connecting parameters in filters and layers. Moreover, it encounters a complete retraining process if the structure is not sufficient to model the system. The BLS is established in the form of a flat network, where the original inputs are transferred and placed as "mapped features" in feature nodes and the structure is expanded in wide sense in the "enhancement nodes." The incremental learning algorithms are developed for fast remodeling in broad expansion without a retraining process if the network deems to be expanded. Two incremental learning algorithms are given for both the increment of the feature nodes (or filters in deep structure) and the increment of the enhancement nodes. The designed model and algorithms are very versatile for selecting a model rapidly. In addition, another incremental learning is developed for a system that has been modeled encounters a new incoming input. Specifically, the system can be remodeled in an incremental way without the entire retraining from the beginning. Satisfactory result for model reduction using singular value decomposition is conducted to simplify the final structure. Compared with existing deep neural networks, experimental results on the Modified National Institute of Standards and Technology database and NYU NORB object recognition dataset benchmark data demonstrate the effectiveness of the proposed BLS.

Phase retrieval via incremental truncated amplitude flow algorithm

Science.gov (United States)

Zhang, Quanbing; Wang, Zhifa; Wang, Linjie; Cheng, Shichao

2017-10-01

This paper considers the phase retrieval problem of recovering the unknown signal from the given quadratic measurements. A phase retrieval algorithm based on Incremental Truncated Amplitude Flow (ITAF) which combines the ITWF algorithm and the TAF algorithm is proposed. The proposed ITAF algorithm enhances the initialization by performing both of the truncation methods used in ITWF and TAF respectively, and improves the performance in the gradient stage by applying the incremental method proposed in ITWF to the loop stage of TAF. Moreover, the original sampling vector and measurements are preprocessed before initialization according to the variance of the sensing matrix. Simulation experiments verified the feasibility and validity of the proposed ITAF algorithm. The experimental results show that it can obtain higher success rate and faster convergence speed compared with other algorithms. Especially, for the noiseless random Gaussian signals, ITAF can recover any real-valued signal accurately from the magnitude measurements whose number is about 2.5 times of the signal length, which is close to the theoretic limit (about 2 times of the signal length). And it usually converges to the optimal solution within 20 iterations which is much less than the state-of-the-art algorithms.

A simple extension of contraction theory to study incremental stability properties

DEFF Research Database (Denmark)

Jouffroy, Jerome

Contraction theory is a recent tool enabling to study the stability of nonlinear systems trajectories with respect to one another, and therefore belongs to the class of incremental stability methods. In this paper, we extend the original definition of contraction theory to incorporate...... in an explicit manner the control input of the considered system. Such an extension, called universal contraction, is quite analogous in spirit to the well-known Input-to-State Stability (ISS). It serves as a simple formulation of incremental ISS, external stability, and detectability in a differential setting....... The hierarchical combination result of contraction theory is restated in this framework, and a differential small-gain theorem is derived from results already available in Lyapunov theory....

Incremental Theory of Intelligence Moderated the Relationship between Prior Achievement and School Engagement in Chinese High School Students.

Science.gov (United States)

Li, Ping; Zhou, Nan; Zhang, Yuchi; Xiong, Qing; Nie, Ruihong; Fang, Xiaoyi

2017-01-01

School engagement plays a prominent role in promoting academic accomplishments. In contrast to the relative wealth of research that examined the impact of students' school engagement on their academic achievement, considerably less research has investigated the effect of high school students' prior achievement on their school engagement. The present study examined the relationship between prior achievement and school engagement among Chinese high school students. Based on the Dweck's social-cognitive theory of motivation, we further examined the moderating effect of students' theories of intelligence (TOIs) on this relationship. A total of 4036 (2066 girls) students from five public high school enrolled in grades 10 reported their high school entrance exam achievement in Chinese, Math and English, school engagement, and TOIs. Results showed that (a) students' prior achievement predicted their behavioral, emotional, and cognitive engagement, respectively, and (b) the association between prior achievement and behavioral, emotional, and cognitive engagement is strong for students with an incremental theory but not for those with an entity theory in the emotional and cognitive engagement. These findings suggest that prior achievement and incremental theory were implicated in relation to adolescents' school engagement. Implications and future research directions were discussed.

Incremental Theory of Intelligence Moderated the Relationship between Prior Achievement and School Engagement in Chinese High School Students

Directory of Open Access Journals (Sweden)

Ping Li

2017-09-01

Full Text Available School engagement plays a prominent role in promoting academic accomplishments. In contrast to the relative wealth of research that examined the impact of students’ school engagement on their academic achievement, considerably less research has investigated the effect of high school students’ prior achievement on their school engagement. The present study examined the relationship between prior achievement and school engagement among Chinese high school students. Based on the Dweck’s social-cognitive theory of motivation, we further examined the moderating effect of students’ theories of intelligence (TOIs on this relationship. A total of 4036 (2066 girls students from five public high school enrolled in grades 10 reported their high school entrance exam achievement in Chinese, Math and English, school engagement, and TOIs. Results showed that (a students’ prior achievement predicted their behavioral, emotional, and cognitive engagement, respectively, and (b the association between prior achievement and behavioral, emotional, and cognitive engagement is strong for students with an incremental theory but not for those with an entity theory in the emotional and cognitive engagement. These findings suggest that prior achievement and incremental theory were implicated in relation to adolescents’ school engagement. Implications and future research directions were discussed.

Performance of hybrid-ARQ with incremental redundancy over relay channels

KAUST Repository

Chelli, Ali; Alouini, Mohamed-Slim

2012-01-01

In this paper, we consider a relay network consisting of a source, a relay, and a destination. The source transmits a message to the destination using hybrid automatic repeat request (HARQ) with incremental redundancy (IR). The relay overhears

Thermomechanical simulations and experimental validation for high speed incremental forming

Science.gov (United States)

Ambrogio, Giuseppina; Gagliardi, Francesco; Filice, Luigino; Romero, Natalia

2016-10-01

Incremental sheet forming (ISF) consists in deforming only a small region of the workspace through a punch driven by a NC machine. The drawback of this process is its slowness. In this study, a high speed variant has been investigated from both numerical and experimental points of view. The aim has been the design of a FEM model able to perform the material behavior during the high speed process by defining a thermomechanical model. An experimental campaign has been performed by a CNC lathe with high speed to test process feasibility. The first results have shown how the material presents the same performance than in conventional speed ISF and, in some cases, better material behavior due to the temperature increment. An accurate numerical simulation has been performed to investigate the material behavior during the high speed process confirming substantially experimental evidence.

Incremental Volumetric Remapping Method: Analysis and Error Evaluation

International Nuclear Information System (INIS)

Baptista, A. J.; Oliveira, M. C.; Rodrigues, D. M.; Menezes, L. F.; Alves, J. L.

2007-01-01

In this paper the error associated with the remapping problem is analyzed. A range of numerical results that assess the performance of three different remapping strategies, applied to FE meshes that typically are used in sheet metal forming simulation, are evaluated. One of the selected strategies is the previously presented Incremental Volumetric Remapping method (IVR), which was implemented in the in-house code DD3TRIM. The IVR method fundaments consists on the premise that state variables in all points associated to a Gauss volume of a given element are equal to the state variable quantities placed in the correspondent Gauss point. Hence, given a typical remapping procedure between a donor and a target mesh, the variables to be associated to a target Gauss volume (and point) are determined by a weighted average. The weight function is the Gauss volume percentage of each donor element that is located inside the target Gauss volume. The calculus of the intersecting volumes between the donor and target Gauss volumes is attained incrementally, for each target Gauss volume, by means of a discrete approach. The other two remapping strategies selected are based in the interpolation/extrapolation of variables by using the finite element shape functions or moving least square interpolants. The performance of the three different remapping strategies is address with two tests. The first remapping test was taken from a literature work. The test consists in remapping successively a rotating symmetrical mesh, throughout N increments, in an angular span of 90 deg. The second remapping error evaluation test consists of remapping an irregular element shape target mesh from a given regular element shape donor mesh and proceed with the inverse operation. In this second test the computation effort is also measured. The results showed that the error level associated to IVR can be very low and with a stable evolution along the number of remapping procedures when compared with the

Methods of determining incremental energy costs for economic dispatch and inter-utility interchange in Canadian utilities

International Nuclear Information System (INIS)

El-Hawary, M.E.; El-Hawary, F.; Mbamalu, G.A.N.

1991-01-01

A questionnaire was mailed to ten Canadian utilities to determine the methods the utilities use in determining the incremental cost of delivering energy at any time. The questionnaire was divided into three parts: generation, transmission and general. The generation section dealt with heat rates, fuel, operation and maintenance, startup and shutdown, and method of prioritizing and economic evaluation of interchange transactions. Transmission dealt with inclusion of transmission system incremental maintenance costs, and transmission losses determination. The general section dealt with incremental costs aspects, and various other economic considerations. A summary is presented of responses to the questionnaire

Fasting Lipoprotein Lipase Protein Levels Can Predict a Postmeal Increment of Triglyceride Levels in Fasting Normohypertriglyceridemic Subjects.

Science.gov (United States)

Tsuzaki, Kokoro; Kotani, Kazuhiko; Yamada, Kazunori; Sakane, Naoki

2016-09-01

Although a postprandial increment in triglyceride (TG) levels is considered to be a risk factor for atherogenesis, tests (e.g., fat load) to assess postprandial changes in TG levels cannot be easily applied to clinical practice. Therefore, fasting markers that predict postprandial TG states are needed to be developed. One current candidate is lipoprotein lipase (LPL) protein, a molecule that hydrides TGs. This study investigated whether fasting LPL levels could predict postprandial TG levels. A total of 17 subjects (11 men, 6 women, mean age 52 ± 11 years) with normotriglyceridemia during fasting underwent the meal test. Several fasting parameters, including LPL, were measured for the area under the curve of postprandial TGs (AUC-TG). The subjects' mean fasting TG level was 1.30 mmol/l, and their mean LPL level was 41.6 ng/ml. The subjects' TG levels increased after loading (they peaked after two postprandial hours). Stepwise multiple regression analysis demonstrated that fasting TG levels were a predictor of the AUC-TG. In addition, fasting LPL mass levels were found to be a predictor of the AUC-TG (β = 0.65, P fasting TG levels. Fasting LPL levels may be useful to predict postprandial TG increment in this population. © 2015 Wiley Periodicals, Inc.

Endogenous-cue prospective memory involving incremental updating of working memory: an fMRI study.

Science.gov (United States)

Halahalli, Harsha N; John, John P; Lukose, Ammu; Jain, Sanjeev; Kutty, Bindu M

2015-11-01

Prospective memory paradigms are conventionally classified on the basis of event-, time-, or activity-based intention retrieval. In the vast majority of such paradigms, intention retrieval is provoked by some kind of external event. However, prospective memory retrieval cues that prompt intention retrieval in everyday life are commonly endogenous, i.e., linked to a specific imagined retrieval context. We describe herein a novel prospective memory paradigm wherein the endogenous cue is generated by incremental updating of working memory, and investigated the hemodynamic correlates of this task. Eighteen healthy adult volunteers underwent functional magnetic resonance imaging while they performed a prospective memory task where the delayed intention was triggered by an endogenous cue generated by incremental updating of working memory. Working memory and ongoing task control conditions were also administered. The 'endogenous-cue prospective memory condition' with incremental working memory updating was associated with maximum activations in the right rostral prefrontal cortex, and additional activations in the brain regions that constitute the bilateral fronto-parietal network, central and dorsal salience networks as well as cerebellum. In the working memory control condition, maximal activations were noted in the left dorsal anterior insula. Activation of the bilateral dorsal anterior insula, a component of the central salience network, was found to be unique to this 'endogenous-cue prospective memory task' in comparison to previously reported exogenous- and endogenous-cue prospective memory tasks without incremental working memory updating. Thus, the findings of the present study highlight the important role played by the dorsal anterior insula in incremental working memory updating that is integral to our endogenous-cue prospective memory task.

An Incremental Time-delay Neural Network for Dynamical Recurrent Associative Memory

Institute of Scientific and Technical Information of China (English)

无

2002-01-01

An incremental time-delay neural network based on synapse growth, which is suitable for dynamic control and learning of autonomous robots, is proposed to improve the learning and retrieving performance of dynamical recurrent associative memory architecture. The model allows steady and continuous establishment of associative memory for spatio-temporal regularities and time series in discrete sequence of inputs. The inserted hidden units can be taken as the long-term memories that expand the capacity of network and sometimes may fade away under certain condition. Preliminary experiment has shown that this incremental network may be a promising approach to endow autonomous robots with the ability of adapting to new data without destroying the learned patterns. The system also benefits from its potential chaos character for emergence.

Analytic description of the frictionally engaged in-plane bending process incremental swivel bending (ISB)

Science.gov (United States)

Frohn, Peter; Engel, Bernd; Groth, Sebastian

2018-05-01

Kinematic forming processes shape geometries by the process parameters to achieve a more universal process utilizations regarding geometric configurations. The kinematic forming process Incremental Swivel Bending (ISB) bends sheet metal strips or profiles in plane. The sequence for bending an arc increment is composed of the steps clamping, bending, force release and feed. The bending moment is frictionally engaged by two clamping units in a laterally adjustable bending pivot. A minimum clamping force hindering the material from slipping through the clamping units is a crucial criterion to achieve a well-defined incremental arc. Therefore, an analytic description of a singular bent increment is developed in this paper. The bending moment is calculated by the uniaxial stress distribution over the profiles' width depending on the bending pivot's position. By a Coulomb' based friction model, necessary clamping force is described in dependence of friction, offset, dimensions of the clamping tools and strip thickness as well as material parameters. Boundaries for the uniaxial stress calculation are given in dependence of friction, tools' dimensions and strip thickness. The results indicate that changing the bending pivot to an eccentric position significantly affects the process' bending moment and, hence, clamping force, which is given in dependence of yield stress and hardening exponent. FE simulations validate the model with satisfactory accordance.

Public Key Infrastructure Increment 2 (PKI Inc 2)

Science.gov (United States)

2016-03-01

across the Global Information Grid (GIG) and at rest. Using authoritative data, obtained via face-to-face identity proofing, PKI creates a credential ...operating on a network by provision of assured PKI-based credentials for any device on that network. ​​​​PKI Increment One made significant...provide assured/secure validation of revocation of an electronic/ digital credential . 2.DoD PKI shall support assured revocation status requests of

Translation of incremental talk test responses to steady-state exercise training intensity.

Science.gov (United States)

Lyon, Ellen; Menke, Miranda; Foster, Carl; Porcari, John P; Gibson, Mark; Bubbers, Terresa

2014-01-01

The Talk Test (TT) is a submaximal, incremental exercise test that has been shown to be useful in prescribing exercise training intensity. It is based on a subject's ability to speak comfortably during exercise. This study defined the amount of reduction in absolute workload intensity from an incremental exercise test using the TT to give appropriate absolute training intensity for cardiac rehabilitation patients. Patients in an outpatient rehabilitation program (N = 30) performed an incremental exercise test with the TT given every 2-minute stage. Patients rated their speech comfort after reciting a standardized paragraph. Anything other than a "yes" response was considered the "equivocal" stage, while all preceding stages were "positive" stages. The last stage with the unequivocally positive ability to speak was the Last Positive (LP), and the preceding stages were (LP-1 and LP-2). Subsequently, three 20-minute steady-state training bouts were performed in random order at the absolute workload at the LP, LP-1, and LP-2 stages of the incremental test. Speech comfort, heart rate (HR), and rating of perceived exertion (RPE) were recorded every 5 minutes. The 20-minute exercise training bout was completed fully by LP (n = 19), LP-1 (n = 28), and LP-2 (n = 30). Heart rate, RPE, and speech comfort were similar through the LP-1 and LP-2 tests, but the LP stage was markedly more difficult. Steady-state exercise training intensity was easily and appropriately prescribed at intensity associated with the LP-1 and LP-2 stages of the TT. The LP stage may be too difficult for patients in a cardiac rehabilitation program.

Some theoretical aspects of capacity increment in gaseous diffusion

Energy Technology Data Exchange (ETDEWEB)

Coates, J. H.; Guais, J. C.; Lamorlette, G.

1975-09-01

Facing to the sharply growing needs of enrichment services, the problem of implementing new capacities must be included in an optimized scheme spread out in time. In this paper the alternative solutions will be studied first for an unique increment decision, and then in an optimum schedule. The limits of the analysis will be discussed.

How to Perform Precise Soil and Sediment Sampling? One solution: The Fine Increment Soil Collector (FISC)

Energy Technology Data Exchange (ETDEWEB)

Mabit, L.; Toloza, A. [Soil and Water Management and Crop Nutrition Laboratory, IAEA, Seibersdorf (Austria); Meusburger, K.; Alewell, C. [Environmental Geosciences, Department of Environmental Sciences, University of Basel, Basel (Switzerland); Iurian, A-R. [Babes-Bolyai University, Faculty of Environmental Science and Engineering, Cluj-Napoca (Romania); Owens, P. N. [Environmental Science Program and Quesnel River Research Centre, University of Northern British Columbia, Prince George, British Columbia (Canada)

2014-07-15

Soil and sediment related research for terrestrial agrienvironmental assessments requires accurate depth incremental sampling to perform detailed analysis of physical, geochemical and biological properties of soil and exposed sediment profiles. Existing equipment does not allow collecting soil/sediment increments at millimetre resolution. The Fine Increment Soil Collector (FISC), developed by the SWMCN Laboratory, allows much greater precision in incremental soil/sediment sampling. It facilitates the easy recovery of collected material by using a simple screw-thread extraction system (see Figure 1). The FISC has been designed specifically to enable standardized scientific investigation of shallow soil/sediment samples. In particular, applications have been developed in two IAEA Coordinated Research Projects (CRPs): CRP D1.20.11 on “Integrated Isotopic Approaches for an Area-wide Precision Conservation to Control the Impacts of Agricultural Practices on Land Degradation and Soil Erosion” and CRP D1.50.15 on “Response to Nuclear Emergencies Affecting Food and Agriculture.”.

How to Perform Precise Soil and Sediment Sampling? One solution: The Fine Increment Soil Collector (FISC)

International Nuclear Information System (INIS)

Mabit, L.; Toloza, A.; Meusburger, K.; Alewell, C.; Iurian, A-R.; Owens, P.N.

2014-01-01

Soil and sediment related research for terrestrial agrienvironmental assessments requires accurate depth incremental sampling to perform detailed analysis of physical, geochemical and biological properties of soil and exposed sediment profiles. Existing equipment does not allow collecting soil/sediment increments at millimetre resolution. The Fine Increment Soil Collector (FISC), developed by the SWMCN Laboratory, allows much greater precision in incremental soil/sediment sampling. It facilitates the easy recovery of collected material by using a simple screw-thread extraction system (see Figure 1). The FISC has been designed specifically to enable standardized scientific investigation of shallow soil/sediment samples. In particular, applications have been developed in two IAEA Coordinated Research Projects (CRPs): CRP D1.20.11 on “Integrated Isotopic Approaches for an Area-wide Precision Conservation to Control the Impacts of Agricultural Practices on Land Degradation and Soil Erosion” and CRP D1.50.15 on “Response to Nuclear Emergencies Affecting Food and Agriculture.”

Respiratory ammonia output and blood ammonia concentration during incremental exercise

NARCIS (Netherlands)

Ament, W; Huizenga, [No Value; Kort, E; van der Mark, TW; Grevink, RG; Verkerke, GJ

The aim of this study was to investigate whether the increase of ammonia concentration and lactate concentration in blood was accompanied by an increased expiration of ammonia during graded exercise. Eleven healthy subjects performed an incremental cycle ergometer test. Blood ammonia, blood lactate

Identifying the Academic Rising Stars via Pairwise Citation Increment Ranking

KAUST Repository

Zhang, Chuxu; Liu, Chuang; Yu, Lu; Zhang, Zi-Ke; Zhou, Tao

2017-01-01

success academic careers. In this work, given a set of young researchers who have published the first first-author paper recently, we solve the problem of how to effectively predict the top k% researchers who achieve the highest citation increment in Δt

Incremental concept learning with few training examples and hierarchical classification

NARCIS (Netherlands)

Bouma, H.; Eendebak, P.T.; Schutte, K.; Azzopardi, G.; Burghouts, G.J.

2015-01-01

Object recognition and localization are important to automatically interpret video and allow better querying on its content. We propose a method for object localization that learns incrementally and addresses four key aspects. Firstly, we show that for certain applications, recognition is feasible

Incremental learning of skill collections based on intrinsic motivation

Science.gov (United States)

Metzen, Jan H.; Kirchner, Frank

2013-01-01

Life-long learning of reusable, versatile skills is a key prerequisite for embodied agents that act in a complex, dynamic environment and are faced with different tasks over their lifetime. We address the question of how an agent can learn useful skills efficiently during a developmental period, i.e., when no task is imposed on him and no external reward signal is provided. Learning of skills in a developmental period needs to be incremental and self-motivated. We propose a new incremental, task-independent skill discovery approach that is suited for continuous domains. Furthermore, the agent learns specific skills based on intrinsic motivation mechanisms that determine on which skills learning is focused at a given point in time. We evaluate the approach in a reinforcement learning setup in two continuous domains with complex dynamics. We show that an intrinsically motivated, skill learning agent outperforms an agent which learns task solutions from scratch. Furthermore, we compare different intrinsic motivation mechanisms and how efficiently they make use of the agent's developmental period. PMID:23898265

The Boundary Between Planning and Incremental Budgeting: Empirical Examination in a Publicly-Owned Corporation

OpenAIRE

S. K. Lioukas; D. J. Chambers

1981-01-01

This paper is a study within the field of public budgeting. It focuses on the capital budget, and it attempts to model and analyze the capital budgeting process using a framework previously developed in the literature of incremental budgeting. Within this framework the paper seeks to determine empirically whether the movement of capital expenditure budgets can be represented as the routine application of incremental adjustments over an existing base of allocations and whether further, forward...

Role of QA in total quality management environment

International Nuclear Information System (INIS)

McCarthy, J.B.; Ayres, R.A.

1992-01-01

A successful company in today's highly competitive business environment must emphasize quality in all activities at all times. For most companies, this requires a major cultural change to establish appropriate operating attitudes and priorities. A total quality environment is required where quality becomes a way of life, and this process must be carefully managed. It will not be accomplished in a few short months with a simple management pronouncement. Instead, it evolves over a period of years through continuous incremental improvement. This evolution towards total quality requires a dramatic change in the quality assurance (QA) function of most companies. Traditionally, quality was automatically equated to QA and its attendant procedures and personnel. Now, quality is becoming a global concept, and QA can play a significant role in the process. The QA profession must, however, recognize and accept a new role as consultant, coach, and partner in today's total quality game. The days of the hard-line enforcer of procedural requirements are gone

Incremental value of myocardial perfusion over coronary angiography by spectral computed tomography in patients with intermediate to high likelihood of coronary artery disease

Energy Technology Data Exchange (ETDEWEB)

Carrascosa, Patricia M., E-mail: investigacion@diagnosticomaipu.com.ar; Deviggiano, Alejandro; Capunay, Carlos; Campisi, Roxana; López Munain, Marina de; Vallejos, Javier; Tajer, Carlos; Rodriguez-Granillo, Gaston A.

2015-04-15

Highlights: •We evaluated myocardial perfusion by dual energy computed tomography (DECT). •We included patients with intermediate to high likelihood of coronary artery disease. •Stress myocardial perfusion by DECT had a reliable accuracy for the detection of ischemia. •Stress myocardial perfusion with DECT showed an incremental value over anatomical evaluation. •DECT imaging was associated to a significant reduction in radiation dose compared to SPECT. -- Abstract: Purpose: We sought to explore the diagnostic performance of dual energy computed tomography (DECT) for the evaluation of myocardial perfusion in patients with intermediate to high likelihood of coronary artery disease (CAD). Materials and methods: Consecutive patients with known or suspected CAD referred for myocardial perfusion imaging by single-photon emission computed tomography (SPECT) constituted the study population and were scanned using a DECT scanner equipped with gemstone detectors for spectral imaging, and a SPECT. The same pharmacological stress was used for both scans. Results: Twenty-five patients were prospectively included in the study protocol. The mean age was 63.4 ± 10.6 years. The total mean effective radiation dose was 7.5 ± 1.2 mSv with DECT and 8.2 ± 1.7 mSv with SPECT (p = 0.007). A total of 425 left ventricular segments were evaluated by DECT, showing a reliable accuracy for the detection of reversible perfusion defects [area under ROC curve (AUC) 0.84 (0.80–0.87)]. Furthermore, adding stress myocardial perfusion provided a significant incremental value over anatomical evaluation alone by computed tomography coronary angiography [AUC 0.70 (0.65–0.74), p = 0.003]. Conclusions: In this pilot investigation, stress myocardial perfusion by DECT demonstrated a significant incremental value over anatomical evaluation alone by CTCA for the detection of reversible perfusion defects.

Maximal power output during incremental exercise by resistance and endurance trained athletes.

Science.gov (United States)

Sakthivelavan, D S; Sumathilatha, S

2010-01-01

This study was aimed at comparing the maximal power output by resistance trained and endurance trained athletes during incremental exercise. Thirty male athletes who received resistance training (Group I) and thirty male athletes of similar age group who received endurance training (Group II) for a period of more than 1 year were chosen for the study. Physical parameters were measured and exercise stress testing was done on a cycle ergometer with a portable gas analyzing system. The maximal progressive incremental cycle ergometer power output at peak exercise and carbon dioxide production at VO2max were measured. Highly significant (P biofeedback and perk up the athlete's performance.

IDEA Clean Energy Application Center

Energy Technology Data Exchange (ETDEWEB)

Thornton, Robert P. [International District Energy Association, Westborough, MA (United States)

2013-12-20

/feasibility tool for these types of community energy projects. The Excel based tool incorporates hourly climate based building loads data to arrive at the composite energy demand for the district and compares the Net Present Value (NPV) of the costs of CHP/DE alternatives. This tool has been used to provide assistance to several projects in the Northeast, Mid-Atlantic, Intermountain and Pacific Regions. The tool was disseminated to the CEACs and supplemented by a Training Webinar and a How to Guide IDEA produced a US Community Energy Development Guide to support mayors, planners, community leaders, real estate developers and economic development officials who are interested in planning more sustainable urban energy infrastructure, creating community energy master plans and implementing CHP/ District Energy systems in cities, communities and towns. IDEA has collected industry data and provided a comprehensive data set containing information on District Energy installations in the US. District energy systems are present in 49 states and theDistrict of Columbia. Of the 597 systems 55% were DE alone while the remainder was some combination of CHP, district heating, and district cooling. District energy systems that do not currently involve electric generation are strong near-term candidates for the adoption of CHP due to the magnitude of their aggregated thermal load. This data has helped inform specific and targeted initiatives including technical assistance provided by the CEAC’s for EPA’s Boiler MACT Compliance by large District Heating System boilers. These outcomes have been greatly enabled by the close coordination and collaboration with DOE CEAC leadership and with the eight regional US DOE Clean Energy Application Centers and the award’s incremental funding has allowed IDEA to leverage our resources to be an effective champion for Clean Energy.

Enthalpy-increment measurements for CsI(s) and Cs2CrO4(s) by high-temperature Calvet calorimetry

International Nuclear Information System (INIS)

Venugopal, V.; Agarwal, R.; Roy, K.N.; Prasad, R.; Sood, D.D.

1987-01-01

Molar thermodynamic properties of CsI(s) and Cs 2 Cr O 4 (s) have been evaluated by enthalpy-increment measurements, using a Calvet high-temperature calorimeter. Least squares analyses were performed on the enthalpy increment results. Data is presented in tabular form for the dependence of enthalpy increments on temperature, in the range 333 to 822 K, for both caesium compounds, along with the thermal properties of the compounds. Good agreement is found between the present data and previously reported results on reduced enthalpy increments of CsI(s) and Cs 2 CrO 4 (s). (U.K.)

Investigation of the prospect of energy self-sufficiency and technical performance of an integrated PEMFC (proton exchange membrane fuel cell), dairy farm and biogas plant system

International Nuclear Information System (INIS)

Guan, Tingting; Alvfors, Per; Lindbergh, Göran

2014-01-01

Highlights: • A PEMFC stack with a 40% of electrical efficiency will make the integrated PEMFC-CHP, biogas plant and dairy farm self-sufficient. • The quality of the reformate gas is good enough to support normal operation of the PEMFC-CHP. • The methane conversion rate and the content of the CH 4 in the biogas need to be balanced in order to obtain the best system performance. • Compared with a coal-fired CHP plant, the integrated system can avoid coal consumption and CO 2 emissions. - Abstract: A PEMFC fuelled with hydrogen is known for its high efficiency and low local emissions. However, the generation of hydrogen is always a controversial issue for the application of the PEMFC due to the use of fossil fuel and the possible carbon dioxide emissions. Presently, the PEMFC-CHP fed with renewable fuels, such as biogas, appears to be the most attractive energy converter–fuel combination. In this paper, an integrated PEMFC-CHP, a dairy farm and a biogas plant are studied. A PEMFC-CHP fed with reformate gas from the biogas plant generates electricity and heat to a dairy farm and a biogas plant, while the dairy farm delivers wet manure to the biogas plant as the feedstock for biogas production. This integrated system has been modelled for steady-state conditions by using Aspen Plus®. The results indicate that the wet manure production of a dairy farm with 300 milked cows can support a biogas plant to give 1280 MW h of biogas annually. Based on the biogas production, a PEMFC-CHP with a stack having an electrical efficiency of 40% generates 360 MW h electricity and 680 MW h heat per year, which is enough to cover the energy demand of the whole system while the total efficiency of the PEMFC-CHP system is 82%. The integrated PEMFC-CHP, dairy farm and biogas plant could make the dairy farm and the biogas plant self-sufficient in a sustainable way provided the PEMFC-CHP has the electrical efficiency stated above. The effect of the methane conversion rate and the

Toward translational incremental similarity-based reasoning in breast cancer grading

Science.gov (United States)

Tutac, Adina E.; Racoceanu, Daniel; Leow, Wee-Keng; Müller, Henning; Putti, Thomas; Cretu, Vladimir

2009-02-01

One of the fundamental issues in bridging the gap between the proliferation of Content-Based Image Retrieval (CBIR) systems in the scientific literature and the deficiency of their usage in medical community is based on the characteristic of CBIR to access information by images or/and text only. Yet, the way physicians are reasoning about patients leads intuitively to a case representation. Hence, a proper solution to overcome this gap is to consider a CBIR approach inspired by Case-Based Reasoning (CBR), which naturally introduces medical knowledge structured by cases. Moreover, in a CBR system, the knowledge is incrementally added and learned. The purpose of this study is to initiate a translational solution from CBIR algorithms to clinical practice, using a CBIR/CBR hybrid approach. Therefore, we advance the idea of a translational incremental similarity-based reasoning (TISBR), using combined CBIR and CBR characteristics: incremental learning of medical knowledge, medical case-based structure of the knowledge (CBR), image usage to retrieve similar cases (CBIR), similarity concept (central for both paradigms). For this purpose, three major axes are explored: the indexing, the cases retrieval and the search refinement, applied to Breast Cancer Grading (BCG), a powerful breast cancer prognosis exam. The effectiveness of this strategy is currently evaluated over cases provided by the Pathology Department of Singapore National University Hospital, for the indexing. With its current accuracy, TISBR launches interesting perspectives for complex reasoning in future medical research, opening the way to a better knowledge traceability and a better acceptance rate of computer-aided diagnosis assistance among practitioners.

Evaluation of incremental reactivity and its uncertainty in Southern California.

Science.gov (United States)

Martien, Philip T; Harley, Robert A; Milford, Jana B; Russell, Armistead G

2003-04-15

The incremental reactivity (IR) and relative incremental reactivity (RIR) of carbon monoxide and 30 individual volatile organic compounds (VOC) were estimated for the South Coast Air Basin using two photochemical air quality models: a 3-D, grid-based model and a vertically resolved trajectory model. Both models include an extended version of the SAPRC99 chemical mechanism. For the 3-D modeling, the decoupled direct method (DDM-3D) was used to assess reactivities. The trajectory model was applied to estimate uncertainties in reactivities due to uncertainties in chemical rate parameters, deposition parameters, and emission rates using Monte Carlo analysis with Latin hypercube sampling. For most VOC, RIRs were found to be consistent in rankings with those produced by Carter using a box model. However, 3-D simulations show that coastal regions, upwind of most of the emissions, have comparatively low IR but higher RIR than predicted by box models for C4-C5 alkenes and carbonyls that initiate the production of HOx radicals. Biogenic VOC emissions were found to have a lower RIR than predicted by box model estimates, because emissions of these VOC were mostly downwind of the areas of primary ozone production. Uncertainties in RIR of individual VOC were found to be dominated by uncertainties in the rate parameters of their primary oxidation reactions. The coefficient of variation (COV) of most RIR values ranged from 20% to 30%, whereas the COV of absolute incremental reactivity ranged from about 30% to 40%. In general, uncertainty and variability both decreased when relative rather than absolute reactivity metrics were used.

Cost of Incremental Expansion of an Existing Family Medicine Residency Program.

Science.gov (United States)

Ashkin, Evan A; Newton, Warren P; Toomey, Brian; Lingley, Ronald; Page, Cristen P

2017-07-01

Expanding residency training programs to address shortages in the primary care workforce is challenged by the present graduate medical education (GME) environment. The Medicare funding cap on new GME positions and reductions in the Health Resources and Services Administration (HRSA) Teaching Health Center (THC) GME program require innovative solutions to support primary care residency expansion. Sparse literature exists to assist in predicting the actual cost of incremental expansion of a family medicine residency program without federal or state GME support. In 2011 a collaboration to develop a community health center (CHC) academic medical partnership (CHAMP), was formed and created a THC as a training site for expansion of an existing family medicine residency program. The cost of expansion was a critical factor as no Federal GME funding or HRSA THC GME program support was available. Initial start-up costs were supported by a federal grant and local foundations. Careful financial analysis of the expansion has provided actual costs per resident of the incremental expansion of the residencyRESULTS: The CHAMP created a new THC and expanded the residency from eight to ten residents per year. The cost of expansion was approximately $72,000 per resident per year. The cost of incremental expansion of our residency program in the CHAMP model was more than 50% less than that of the recently reported cost of training in the HRSA THC GME program.

78 FR 22770 - Immigration Benefits Business Transformation, Increment I; Correction

Science.gov (United States)

2013-04-17

...-2009-0022] RIN 1615-AB83 Immigration Benefits Business Transformation, Increment I; Correction AGENCY...: Background On August 29, 2011, DHS issued a final rule titled, Immigration Benefits Business Transformation... business processes. In this notice, we are correcting three technical errors. DATES: The effective date of...

Sustained change blindness to incremental scene rotation: a dissociation between explicit change detection and visual memory.

Science.gov (United States)

Hollingworth, Andrew; Henderson, John M

2004-07-01

In a change detection paradigm, the global orientation of a natural scene was incrementally changed in 1 degree intervals. In Experiments 1 and 2, participants demonstrated sustained change blindness to incremental rotation, often coming to consider a significantly different scene viewpoint as an unchanged continuation of the original view. Experiment 3 showed that participants who failed to detect the incremental rotation nevertheless reliably detected a single-step rotation back to the initial view. Together, these results demonstrate an important dissociation between explicit change detection and visual memory. Following a change, visual memory is updated to reflect the changed state of the environment, even if the change was not detected.

Modeling and off-design performance of a 1 kWe HT-PEMFC (high temperature-proton exchange membrane fuel cell)-based residential micro-CHP (combined-heat-and-power) system for Danish single-family households

DEFF Research Database (Denmark)

Arsalis, Alexandros; Nielsen, Mads Pagh; Kær, Søren Knudsen

2011-01-01

A novel proposal for the modeling and operation of a micro-CHP (combined-heat-and-power) residential system based on HT-PEMFC (High Temperature-Proton Exchange Membrane Fuel Cell) technology is described and analyzed to investigate its commercialization prospects. An HT-PEMFC operates at elevated...... temperatures, as compared to Nafion-based PEMFCs and therefore can be a significant candidate for cogeneration residential systems. The proposed system can provide electric power, hot water, and space heating for a typical Danish single-family household. A complete fuel processing subsystem, with all necessary...

Incremental value of live/real time three-dimensional transesophageal echocardiography over the two-dimensional technique in the assessment of primary cardiac malignant fibrous histiocytoma.

Science.gov (United States)

Gok, Gulay; Elsayed, Mahmoud; Thind, Munveer; Uygur, Begum; Abtahi, Firoozeh; Chahwala, Jugal R; Yıldırımtürk, Özlem; Kayacıoğlu, İlyas; Pehlivanoğlu, Seçkin; Nanda, Navin C

2015-07-01

We describe a case of primary cardiac malignant fibrous histiocytoma where live/real time three-dimensional transesophageal echocardiography added incremental value to the two-dimensional modalities. Specifically, the three-dimensional technique allowed us to delineate the true extent and infiltration of the tumor, to identify characteristics of the tumor mass suggestive of its malignant nature, and to quantitatively assess the total tumor burden. © 2015, Wiley Periodicals, Inc.

Study on solid phase extraction and graphite furnace atomic absorption spectrometry for the determination of nickel, silver, cobalt, copper, cadmium and lead with MCI GEL CHP 20Y as sorbent

International Nuclear Information System (INIS)

Yang Guangyu; Fen Weibo; Lei Chun; Xiao Weilie; Sun Handong

2009-01-01

A solid phase extraction and graphite furnace atomic absorption spectrometry (GFAAS) for the determination of nickel, silver, cobalt, copper, cadmium and lead with MCI GEL CHP 20Y as sorbent was studied. Trace amounts of chromium, nickel, silver, cobalt, copper, cadmium and lead were reacted with 2-(2-quinolinil-azo)-4-methyl-1,3-dihydroxidobenzene (QAMDHB) followed by adsorption onto MCI GEL CHP 20Y solid phase extraction column, and 1.0 mol L -1 HNO 3 was used as eluent. The metal ions in 300 mL solution can be concentrated to 1.0 mL, representing an enrichment factor of 300 was achieved. The recoveries of analytes at pH 8.0 with 1.0 g of resin were greater than 95% without interference from alkaline, earth alkaline and some metal ions. When detected with graphite furnace atomic absorption spectrometry, the detection limits in the original samples were 1.4 ng L -1 for Cr(III), 1.0 ng L -1 for Ni(II), 0.85 ng L -1 for Ag(I), 1.2 ng L -1 for Co(II), 1.0 ng L -1 for Cu(II), 1.2 ng L -1 for Cd(II) and 1.3 ng L -1 for Pb(II). The validation of the procedure was performed by the analysis of the certified standard reference materials, and the presented procedure was applied to the determination of analytes in biological, water and soil samples with good results (recoveries range from 89 to 104%, and R.S.D.% lower than 3.2%. The results agreed with the standard value or reference method)

Incremental Value of Three-Dimensional Transesophageal Echocardiography over the Two-Dimensional Technique in the Assessment of a Thrombus in Transit through a Patent Foramen Ovale.

Science.gov (United States)

Thind, Munveer; Ahmed, Mustafa I; Gok, Gulay; Joson, Marisa; Elsayed, Mahmoud; Tuck, Benjamin C; Townsley, Matthew M; Klas, Berthold; McGiffin, David C; Nanda, Navin C

2015-05-01

We report a case of a right atrial thrombus traversing a patent foramen ovale into the left atrium, where three-dimensional transesophageal echocardiography provided considerable incremental value over two-dimensional transesophageal echocardiography in its assessment. As well as allowing us to better spatially characterize the thrombus, three-dimensional transesophageal echocardiography provided a more quantitative assessment through estimation of total thrombus burden. © 2015, Wiley Periodicals, Inc.

Identifying the Academic Rising Stars via Pairwise Citation Increment Ranking

KAUST Repository

Zhang, Chuxu

2017-08-02

Predicting the fast-rising young researchers (the Academic Rising Stars) in the future provides useful guidance to the research community, e.g., offering competitive candidates to university for young faculty hiring as they are expected to have success academic careers. In this work, given a set of young researchers who have published the first first-author paper recently, we solve the problem of how to effectively predict the top k% researchers who achieve the highest citation increment in Δt years. We explore a series of factors that can drive an author to be fast-rising and design a novel pairwise citation increment ranking (PCIR) method that leverages those factors to predict the academic rising stars. Experimental results on the large ArnetMiner dataset with over 1.7 million authors demonstrate the effectiveness of PCIR. Specifically, it outperforms all given benchmark methods, with over 8% average improvement. Further analysis demonstrates that temporal features are the best indicators for rising stars prediction, while venue features are less relevant.

Balmorel: A model for analyses of the electricity and CHP markets in the Baltic Sea Region. Appendices

International Nuclear Information System (INIS)

Ravn, H.F.; Munksgaard, J.; Ramskov, J.; Grohnheit, P.E.; Larsen, H.V.

2001-03-01

This report describes the motivations behind the development of the Balmorel model as well as the model itself. The purpose of the Balmorel project is to develop a model for analyses of the power and CHP sectors in the Baltic Sea Region. The model is directed towards the analysis of relevant policy questions to the extent that they contain substantial international aspects. The model is developed in response to the trend towards internationalisation in the electricity sector. This trend is seen in increased international trade of electricity, in investment strategies among producers and otherwise. Also environmental considerations and policies are to an increasing extent gaining an international perspective in relation to the greenhouse gasses. Further, the ongoing process of deregulation of the energy sector highlights this and contributes to the need for overview and analysis. A guiding principle behind the construction of the model has been that it may serve as a means of communication in relation to the policy issues that already are or that may become important for the region. Therefore, emphasis has been put on documentation, transparency and flexibility of the model. This is achieved in part by formulating the model in a high level modelling language, and by making the model, including data, available at the internet. Potential users of the Balmorel model include research institutions, consulting companies, energy authorities, transmission system operators and energy companies. (au)

Effects of frequency and duration on psychometric functions for detection of increments and decrements in sinusoids in noise.

Science.gov (United States)

Moore, B C; Peters, R W; Glasberg, B R

1999-12-01

Psychometric functions for detecting increments or decrements in level of sinusoidal pedestals were measured for increment and decrement durations of 5, 10, 20, 50, 100, and 200 ms and for frequencies of 250, 1000, and 4000 Hz. The sinusoids were presented in background noise intended to mask spectral splatter. A three-interval, three-alternative procedure was used. The results indicated that, for increments, the detectability index d' was approximately proportional to delta I/I. For decrements, d' was approximately proportional to delta L. The slopes of the psychometric functions increased (indicating better performance) with increasing frequency for both increments and decrements. For increments, the slopes increased with increasing increment duration up to 200 ms at 250 and 1000 Hz, but at 4000 Hz they increased only up to 50 ms. For decrements, the slopes increased for durations up to 50 ms, and then remained roughly constant, for all frequencies. For a center frequency of 250 Hz, the slopes of the psychometric functions for increment detection increased with duration more rapidly than predicted by a "multiple-looks" hypothesis, i.e., more rapidly than the square root of duration, for durations up to 50 ms. For center frequencies of 1000 and 4000 Hz, the slopes increased less rapidly than predicted by a multiple-looks hypothesis, for durations greater than about 20 ms. The slopes of the psychometric functions for decrement detection increased with decrement duration at a rate slightly greater than the square root of duration, for durations up to 50 ms, at all three frequencies. For greater durations, the increase in slope was less than proportional to the square root of duration. The results were analyzed using a model incorporating a simulated auditory filter, a compressive nonlinearity, a sliding temporal integrator, and a decision device based on a template mechanism. The model took into account the effects of both the external noise and an assumed internal

Systematic Luby Transform codes as incremental redundancy scheme

CSIR Research Space (South Africa)

Grobler, TL

2011-09-01

Full Text Available Transform Codes as Incremental Redundancy Scheme T. L. Grobler y, E. R. Ackermann y, J. C. Olivier y and A. J. van Zylz Department of Electrical, Electronic and Computer Engineering University of Pretoria, Pretoria 0002, South Africa Email: trienkog...@gmail.com, etienne.ackermann@ieee.org yDefence, Peace, Safety and Security (DPSS) Council for Scientific and Industrial Research (CSIR), Pretoria 0001, South Africa zDepartment of Mathematics and Applied Mathematics University of Pretoria, Pretoria 0002, South...

Deliberate and Crisis Action Planning and Execution Segments Increment 2A (DCAPES Inc 2A)

Science.gov (United States)

2016-03-01

2016 Major Automated Information System Annual Report Deliberate and Crisis Action Planning and Execution Segments Increment 2A (DCAPES Inc 2A...Program Name Deliberate and Crisis Action Planning and Execution Segments Increment 2A (DCAPES Inc 2A) DoD Component Air Force Responsible Office Program...APB) dated March 9, 2015 DCAPES Inc 2A 2016 MAR UNCLASSIFIED 4 Program Description Deliberate and Crisis Action Planning and Execution Segments

Deliberate and Crisis Action Planning and Execution Segments Increment 2B (DCAPES Inc 2B)

Science.gov (United States)

2016-03-01

2016 Major Automated Information System Annual Report Deliberate and Crisis Action Planning and Execution Segments Increment 2B (DCAPES Inc 2B...Information Program Name Deliberate and Crisis Action Planning and Execution Segments Increment 2B (DCAPES Inc 2B) DoD Component Air Force Responsible Office...been established. DCAPES Inc 2B 2016 MAR UNCLASSIFIED 4 Program Description Deliberate and Crisis Action Planning and Execution Segments (DCAPES) is

Blood flow patterns during incremental and steady-state aerobic exercise.

Science.gov (United States)

Coovert, Daniel; Evans, LeVisa D; Jarrett, Steven; Lima, Carla; Lima, Natalia; Gurovich, Alvaro N

2017-05-30

Endothelial shear stress (ESS) is a physiological stimulus for vascular homeostasis, highly dependent on blood flow patterns. Exercise-induced ESS might be beneficial on vascular health. However, it is unclear what type of ESS aerobic exercise (AX) produces. The aims of this study are to characterize exercise-induced blood flow patterns during incremental and steady-state AX. We expect blood flow pattern during exercise will be intensity-dependent and bidirectional. Six college-aged students (2 males and 4 females) were recruited to perform 2 exercise tests on cycleergometer. First, an 8-12-min incremental test (Test 1) where oxygen uptake (VO2), heart rate (HR), blood pressure (BP), and blood lactate (La) were measured at rest and after each 2-min step. Then, at least 48-hr. after the first test, a 3-step steady state exercise test (Test 2) was performed measuring VO2, HR, BP, and La. The three steps were performed at the following exercise intensities according to La: 0-2 mmol/L, 2-4 mmol/L, and 4-6 mmol/L. During both tests, blood flow patterns were determined by high-definition ultrasound and Doppler on the brachial artery. These measurements allowed to determine blood flow velocities and directions during exercise. On Test 1 VO2, HR, BP, La, and antegrade blood flow velocity significantly increased in an intensity-dependent manner (repeated measures ANOVA, pflow velocity did not significantly change during Test 1. On Test 2 all the previous variables significantly increased in an intensity-dependent manner (repeated measures ANOVA, pflow patterns during incremental and steady-state exercises include both antegrade and retrograde blood flows.

Increments in plasma homovanillic acid concentrations after neuroleptic discontinuation are associated with worsening of schizophrenic symptoms.

Science.gov (United States)

Khan, R S; Amin, F; Powchik, P; Knott, P; Goldstein, M; Apter, S; Kerman, B; Jaff, S; Davidson, M

1990-01-01

1. Thirty-two male schizophrenic patients participated in this study. 2. Plasma concentrations of the dopamine metabolite, homovanillic acid (pHVA) were assessed once on neuroleptic medication and twice a week for a maximum of six weeks after its discontinuation. 3. Psychiatric symptomatology was assessed once on neuroleptic medication and once a week for a maximum of six weeks after its discontinuation, using the brief psychiatric rating scale (BPRS). 4. pHVA and total BPRS score increased significantly after discontinuation of neuroleptic as compared to baseline. 5. The magnitude of pHVA and BPRS increments after discontinuation of neuroleptic correlated significantly. 6. Results of this study suggest that worsening of schizophrenic symptoms after discontinuation of neuroleptic treatment is associated with increased pHVA concentrations.