A Basic Study on Countermeasure Against Aerodynamic Force Acting on Train Running Inside Tunnel Using Air Blowing

Science.gov (United States)

Suzuki, Masahiro; Nakade, Koji

A basic study of flow controls using air blowing was conducted to reduce unsteady aerodynamic force acting on trains running in tunnels. An air blowing device is installed around a model car in a wind tunnel. Steady and periodic blowings are examined utilizing electromagnetic valves. Pressure fluctuations are measured and the aerodynamic force acting on the car is estimated. The results are as follows: a) The air blowing allows reducing the unsteady aerodynamic force. b) It is effective to blow air horizontally at the lower side of the car facing the tunnel wall. c) The reduction rate of the unsteady aerodynamic force relates to the rate of momentum of the blowing to that of the uniform flow. d) The periodic blowing with the same frequency as the unsteady aerodynamic force reduces the aerodynamic force in a manner similar to the steady blowing.

Wind Tunnel Testing on Crosswind Aerodynamic Forces Acting on Railway Vehicles

Science.gov (United States)

Kwon, Hyeok-Bin; Nam, Seong-Won; You, Won-Hee

This study is devoted to measure the aerodynamic forces acting on two railway trains, one of which is a high-speed train at 300km/h maximum operation speed, and the other is a conventional train at the operating speed 100km/h. The three-dimensional train shapes have been modeled as detailed as possible including the inter-car, the upper cavity for pantograph, and the bogie systems. The aerodynamic forces on each vehicle of the trains have been measured in the subsonic wind tunnel with 4m×3m test section of Korea Aerospace Research Institute at Daejeon, Korea. The aerodynamic forces and moments of the train models have been plotted for various yaw angles and the characteristics of the aerodynamic coefficients has been discussed relating to the experimental conditions.

Simulation of airflow and aerodynamic forces acting on a commercial turbine ventilator

International Nuclear Information System (INIS)

Farahani, A.S.; Nor Mariah Adam; Khairol Anuar

2009-01-01

Full text: This study is concerned with performing simulation of airflow using Computational Fluid Dynamics (CFD) technique code name FLUENT so as to visualize the flow behavior around and within turbine ventilator in addition to determining the aerodynamic forces acting on turbine ventilator during operation and comparing the simulated results to the wind tunnel experiment. To achieve this, Realizable k-ε and RSM turbulence models are used by taking advantage of moving mesh method to simulate the rotation of turbine ventilator and the consequent results are obtained through the sequential process which ensures accuracy of the computations. The results demonstrated that, the RSM turbulence model shows the best performance on flow visualization and predicting the aerodynamic forces acting on a turbine ventilator. Results from this work would lead us to a noticeable increase in efficiency of future turbine ventilator by enhancing the shape of inner vanes, and redesign them using CFD technique. (author)

On the absorbing force of magnetic fields acting on magnetic particle under magnetic particle examination

International Nuclear Information System (INIS)

Maeda, N.

1988-01-01

During the magnetic particle examination, magnetic particles near defects are deposited by an absorbing force of magnetic fields acting on the magnetic particles. Therefore, a quantitative determination of this absorbing force is a theoretical and experimental basis for solving various problems associated with magnetic particle examinations. The absorbing force is formulated based on a magnetic dipole model, and a measuring method of the absorbing force using magnetic fields formed around linear current is proposed. Measurements according to this method produced appropriate results, verifying the validation of the concept and the measuring method

Unsteady analysis on the instantaneous forces and moment arms acting on a novel Savonius-style wind turbine

International Nuclear Information System (INIS)

Roy, Sukanta; Ducoin, Antoine

2016-01-01

Highlights: • Two-dimensional unsteady simulations on a novel Savonius-style wind turbine. • Instantaneous behavior of drag and lift coefficients, and corresponding moment arms. • Effect of tip speed ratio on the instantaneous force coefficients and moments arms. • Effect of force coefficients and moment arms on the instantaneous moment and power. • Analysis of power and moment coefficients at different tip speed ratios. - Abstract: This paper aims to present a transient analysis on the forces acting on a novel two-bladed Savonius-style wind turbine. Two-dimensional unsteady Reynolds Averaged Navier Stokes equations are solved using shear stress transport k–ω turbulence model at a Reynolds number of 1.23 × 10"5. The instantaneous longitudinal drag and lateral lift forces acting on each of the blades and their acting points are calculated. The corresponding moment arms responsible for the torque generation are obtained. Further, the effect of tip speed ratio on the force coefficients, moment arms and overall turbine performances are observed. Throughout the paper, the obtained results for the new design are discussed with reference to conventional semi-circular design of Savonius turbines. A significant performance improvement is achieved with the new design due to its increased lift and moment arm contribution as compared to the conventional design. More interestingly, the present study sets a platform for future aerodynamic research and improvements for Savonius-style wind turbines.

Torquing an upper central incisor with aligners--acting forces and biomechanical principles.

Science.gov (United States)

Hahn, Wolfram; Zapf, Antonia; Dathe, Henning; Fialka-Fricke, Julia; Fricke-Zech, Susanne; Gruber, Rudolf; Kubein-Meesenburg, Dietmar; Sadat-Khonsari, Reza

2010-12-01

The forces delivered by aligners during torquing have still not been investigated. The purpose of this study was to measure the forces delivered to an upper central incisor during torquing with three different materials of the same thickness, and to describe the biomechanical principles of torquing with aligners. Five identical appliances were manufactured from each of three materials, all with a thickness of 1.0 mm (Ideal Clear®, Erkodur®, and Biolon®). An upper central incisor, as part of the measuring device, was torqued in defined steps in the vestibular and palatal directions with the respective appliance in place. For statistical analysis, the resulting forces, Fx (forces acting in the palatal and facial directions) and Fz (intrusive force as a side-effect) at a displacement of ±0.15 and ±0.8 mm from the tooth at the gingival margin were calculated. The mean Fx forces for ±0.15 mm displacement ranged from -1.89 N [standard deviation (SD) 0.48] to 0.11 N (SD 0.1). The mean Fz forces were between -0.97 N (SD 0.57) and -0.07 N (SD 0.22). The highest intrusive forces were measured during palatal displacement of the measuring tooth. An influence of direction of displacement on the levels of force was observed, especially for Fz at the greater displacement of ±0.8 mm. In relation to the intended amount of root movement during torquing, aligners tend to 'lift up' and therefore no effective force couple can be established for further root control. The force delivery properties are also influenced by the material used and the shape of the tooth.

DelPhiForce web server: electrostatic forces and energy calculations and visualization.

Science.gov (United States)

Li, Lin; Jia, Zhe; Peng, Yunhui; Chakravorty, Arghya; Sun, Lexuan; Alexov, Emil

2017-11-15

Electrostatic force is an essential component of the total force acting between atoms and macromolecules. Therefore, accurate calculations of electrostatic forces are crucial for revealing the mechanisms of many biological processes. We developed a DelPhiForce web server to calculate and visualize the electrostatic forces at molecular level. DelPhiForce web server enables modeling of electrostatic forces on individual atoms, residues, domains and molecules, and generates an output that can be visualized by VMD software. Here we demonstrate the usage of the server for various biological problems including protein-cofactor, domain-domain, protein-protein, protein-DNA and protein-RNA interactions. The DelPhiForce web server is available at: http://compbio.clemson.edu/delphi-force. delphi@clemson.edu. Supplementary data are available at Bioinformatics online. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

Magnetic force acting on a magnetic dipole over a superconducting thin film

International Nuclear Information System (INIS)

Wei, J.C.; Chen, J.L.; Horng, L.; Yang, T.J.

1996-01-01

The magnetostatic interaction energy and corresponding magnetic force acting on a magnetic point dipole placed above a type-II thin superconducting film in the mixed state with a single vortex are calculated using electromagnetics coupled with the London theory of superconductivity. If a vortex is trapped by a circular defect of radius b 1, where a is the separation between the dipole and the thin film, the only difference between two results is in the cutoff length, i.e., in the case of a circular defect the only difference in the critical position calculation is the cutoff at radius b rather than at coherence length ξ. The pinning force of a single vortex by a circular defect is also calculated. Further, we investigate the conditions of the vortex creation for various cases (including the first, second, and third vortices) for a free of pinning center in the examining region. It is found that the creation of a new single vortex in the thin film causes an abrupt change in vertical levitation force: the force changed discontinuously. copyright 1996 The American Physical Society

Air Force Personnel Can Improve Compliance With the Berry Amendment and Buy American Act

Science.gov (United States)

2016-02-24

leather, furs,6 apparel , and shoes • FSG 84 – clothing , individual equipment and insignia • FSG 89 – subsistence (food) If these items are purchased...during the audit by completing Buy American Act training and amending standard operating procedures and internal processes to improve compliance with the...Force Personnel Can Improve Compliance With the Berry Amendment and the Buy American Act F E B R U A R Y 2 4 , 2 0 1 6 Report No. DODIG-2016-051

Calculation of the force acting on a drop in a nonuniform flow of a current-supporting fluid

International Nuclear Information System (INIS)

Korovin, V.M.

1993-01-01

In the context of wide use of intense electric currents in various technological process, it is of practical interest to investigate the characteristics of the force action of electromagnetic fields on a variety of inclusions - solid particles, drops, gas bubbles - suspended in current-supporting fluids. In the available studies one treats the simplest case, in which the vortical component of the electromagnetic forces, generated by the interaction of the current with the internal magnetic field, is nonvanishing only in small vicinities near these inclusions, and therefore these electromagnetic forces do not generate global motion of the homogeneous current-supporting fluid. In practice, in most cases the vortical component of electromagnetic forces plays a substantial role in the whole operating region of the technological device, and the motion of the current-supporting fluid is created specifically by electromagnetic forces. In the case of a varying electromagnetic field the forces acting on particles are located in the conducting fluid, moving under the field action, were calculated by Korovim (Korovim, V. M., open-quotes The calculation of forces acting on suspended particles during the flow of a conducting fluid in a varying electromagnetic field,close quotes Magn. Gidrodin, No. 1 95-102 (1991)). In the present study the authors generalize the method suggested by Korovin for calculating forces applied to both drops and particles and gas bubbles suspended in the gradient flow of a fluid moving under the action of a constant electromagnetic field. 6 refs

Reduction of undesired lateral forces acting on the flapper of a flapper–nozzle pilot valve by using an innovative flapper shape

International Nuclear Information System (INIS)

Zhang, Shengzhuo; Aung, Nay Zar; Li, Songjing

2015-01-01

Highlights: • The simulated flow rate and main flow force show a good agreement with experiments. • The innovative flapper has little influence on the flow-pressure characteristics. • The innovative flapper can greatly reduce the Y direction force on the upper part. • The innovative flapper reduces both the X and Z direction forces on the lower part. - Abstract: The stability and dynamic performance of a flapper–nozzle pilot valve significantly depend on the flow forces acting on the flapper. Due to the shape of the flapper and flow structure in the flapper–nozzle pilot valve there are undesired lateral forces acting on the flapper, which are very potential to interfere with the stability of the flapper. Aiming to reduce these undesired lateral forces, an innovative flapper shape is proposed and a comparative study of flow forces acting on the two different flapper shapes is conducted. A simple rectangle shape is selected as the innovative flapper shape. The flow forces acting on the traditional flapper shape and innovative flapper shape are evaluated by means of CFD (Computational Fluid Dynamics) simulations and verified with the results from the semi-experimental approach. The evaluation of the flow forces is performed for each flapper shape with two different flapper–nozzle clearances of 0.10 mm and 0.05 mm under seven different flow conditions with the variation of inlet pressures from 1 MPa to 7 MPa. A good agreement between CFD results and semi-experimental results shows that the proposed innovative flapper shape has no effect on flow control characteristics since it is giving approximately the same flow rate and main flow force as the traditional flapper shape at every flow condition. Meanwhile the innovative flapper shape effectively reduces the undesired lateral forces acting on the flapper by altering the flow structure and reducing the strength of the jet flow and cavitation occurred in the flow field of flapper–nozzle pilot valve. At the

The impact force acting on a flat plate exposed normally to a rarefied plasma plume issuing from an annular or circular nozzle

Energy Technology Data Exchange (ETDEWEB)

Chen Xi, E-mail: cx-dem@mail.tsinghua.edu.c [Department of Engineering Mechanics, Tsinghua University, Beijing 100084 (China)

2010-08-11

With the indirect thrust measurement of electric thrusters working at a low vacuum chamber pressure as the research background, this paper analyses the impact force acting on a flat plate exposed normally to a rarefied plasma plume issuing from a thruster with an annular or circular exit section for the free-molecule flow regime (at large Knudsen numbers). The constraint relation proposed by Cai and Boyd (2007 J. Spacecr. Rockets 44 619, 1326) about the velocity components of gas particles leaving a location on the nozzle exit section and arriving at a given spatial point outside the nozzle has been employed here to derive the analytical expressions for calculating the impact force. Sample calculation results show that if the flat plate is sufficiently large, the impact force acting on the flat plate calculated for the case without accounting for gas particle reflection at the plate surface agrees well with the axial momentum flux calculated at the thruster exit or the theoretical thrust force of the studied thruster, while accounting for the contribution of gas particles reflected from the plate surface to the impact force production may significantly increase the calculated impact force acting on the flat plate. For a Hall-effect thruster in which the thrust force is dominantly produced by the ions with high directional kinetic energy and the ions are not directly reflected from the plate surface, the contribution to the impact force production of atom species and of gas particles reflected from the plate surface is negligibly small and thus the measured axial impact force acting on a sufficiently large plate can well represent the thrust force of the thruster. On the other hand, if the contribution of the gas particles reflected from the plate surface to the impact force production cannot be neglected (e.g. for the electric thrusters with comparatively low thruster exit temperatures), appreciable error would appear in the indirect thrust measurement.

Modeling of Aerodynamic Force Acting in Tunnel for Analysis of Riding Comfort in a Train

Science.gov (United States)

Kikko, Satoshi; Tanifuji, Katsuya; Sakanoue, Kei; Nanba, Kouichiro

In this paper, we aimed to model the aerodynamic force that acts on a train running at high speed in a tunnel. An analytical model of the aerodynamic force is developed from pressure data measured on car-body sides of a test train running at the maximum revenue operation speed. The simulation of an 8-car train running while being subjected to the modeled aerodynamic force gives the following results. The simulated car-body vibration corresponds to the actual vibration both qualitatively and quantitatively for the cars at the rear of the train. The separation of the airflow at the tail-end of the train increases the yawing vibration of the tail-end car while it has little effect on the car-body vibration of the adjoining car. Also, the effect of the moving velocity of the aerodynamic force on the car-body vibration is clarified that the simulation under the assumption of a stationary aerodynamic force can markedly increase the car-body vibration.

Influence of tire inflating pressure at dynamic forces acting on articulated trolleybus

Directory of Open Access Journals (Sweden)

Polach Pavel

2017-01-01

Full Text Available ŠKODA VÝZKUM s.r.o. cooperated on the development of the NEOPLAN DMA low-floor articulated trolleybus intended for the Boston city. Multibody models and finite element models of the trolleybus were utilized in the stage of the vehicle design. At the end of the stage of computer modelling and testing of the trolleybus prototype a decision to reduce tire inflating of vehicles in serial production (together with the change the type of shock absorbers used in trolleybus suspension was made. The impact of this change on forces acting in the trolleybus suspension elements (i.e. in air springs and shock absorbers and radius rods on the trolleybus chassis when running on an uneven test track was investigated using multibody simulations. Time histories of the forces calculated utilising multibody models were used as input data of the trolleybus finite element models.

General stability of memory-type thermoelastic Timoshenko beam acting on shear force

Science.gov (United States)

Apalara, Tijani A.

2018-03-01

In this paper, we consider a linear thermoelastic Timoshenko system with memory effects where the thermoelastic coupling is acting on shear force under Neumann-Dirichlet-Dirichlet boundary conditions. The same system with fully Dirichlet boundary conditions was considered by Messaoudi and Fareh (Nonlinear Anal TMA 74(18):6895-6906, 2011, Acta Math Sci 33(1):23-40, 2013), but they obtained a general stability result which depends on the speeds of wave propagation. In our case, we obtained a general stability result irrespective of the wave speeds of the system.

Estimation of the forces acting on the tibiofemoral joint during knee extension exercises

Directory of Open Access Journals (Sweden)

Rodrigo Rico Bini

2008-02-01

Full Text Available http://dx.doi.org/10.5007/1980-0037.2008v10n1p35 The objectives of this study were to: (1 evaluate the resistive torque of an open kinetic chain strength-training machine for performing knee extensions, and (2 perform an analysis estimating internal forces in the tibiofemoral joint. During a fi rst phase of the study, measurements were taken of the machine under analysis (external forces, and then calculations were performed to estimate forces on the lower limb (internal forces. Equations were defi ned to calculate human force (HF, and the moment of muscular force (MMF. Perpendicular muscular force (MFp and joint force (JFp, axial muscular force (MF” and joint force (JF”, and total muscular force (MF and joint force (JF were all calculated. Five knee angles were analyzed (zero, 30, 45, 60, and 90 degrees. A reduction was observed in HF at higher knee angles, while MF and JF also increased at the same time. HF was always lower than the load selected on the machine, which indicates a reduced overload imposed by the machine. The reduction observed in MFp and JFp at higher knee angles indicates a lower tendency to shear the tibia in relation to the femur. At the same time, there was an increase in JF” due to higher MF”. The biomechanical model proposed in this study has shown itself adequate for the day-to-day needs of professionals who supervise orient strength training.

Thermomagnetic force acting on an ellipsoidal body immersed into a nonuniformly heated magnetic liquid

International Nuclear Information System (INIS)

Naletova, V.A.; Kvitantsev, A.S.

2002-01-01

A prolate spheroidal body immersed into a nonuniformly heated magnetic liquid in an applied magnetic field has been considered. The expressions for the pressure and velocity of the liquid, temperature and magnetic field have been obtained. The formula for a thermomagnetic force acting on the body has been calculated. It has been shown that the body shape needs to be taken into account when we study the thermomagnetic diffusion of the prolate bodies

Examination of hydrodynamic force acting on a circular cylinder in vortex-induced vibrations in synchronization

Energy Technology Data Exchange (ETDEWEB)

Shen, Linwei; Sun, Zhilin [Ocean College, Zhejiang University, Zhoushan, 316021 (China); Chan, Eng-Soon, E-mail: shenlinwei@zju.edu.cn [Department of Civil and Environmental Engineering, National University of Singapore, No. 1 Engineering Drive 2, Singapore 117576 (Singapore)

2017-04-15

An immersed boundary method is employed to simulate vortex-induced vibrations (VIV) of a circular cylinder in two dimensions. The Reynolds number is 150, and the cylinder mass ratios of 2 and 10 are considered. The synchronization regions for these two mass ratios are determined by the simulations. It is found that the cycle-averaged added mass is about zero at the reduced velocity of 6.1. The instantaneous frequency, which is obtained by Hilbert transformation of the cylinder oscillating displacement, exhibits an important feature whereby the cylinder oscillation in the VIV synchronization region is modulated with a frequency twice the displacement prevailing frequency. The cylinder displacement could still be well approximated by a sine function with a constant frequency and amplitude. However, the lift force acting on the cylinder cannot be estimated in the same manner. In fact, both the lift force amplitude and frequency are modulated. The suggested expression provides a better approximation of the lift force. Moreover, it reveals that the presence of the higher harmonics in the lift force is the result of the amplitude and frequency modulation. (paper)

Dual-joint modeling for estimation of total knee replacement contact forces during locomotion.

Science.gov (United States)

Hast, Michael W; Piazza, Stephen J

2013-02-01

Model-based estimation of in vivo contact forces arising between components of a total knee replacement is challenging because such forces depend upon accurate modeling of muscles, tendons, ligaments, contact, and multibody dynamics. Here we describe an approach to solving this problem with results that are tested by comparison to knee loads measured in vivo for a single subject and made available through the Grand Challenge Competition to Predict in vivo Tibiofemoral Loads. The approach makes use of a "dual-joint" paradigm in which the knee joint is alternately represented by (1) a ball-joint knee for inverse dynamic computation of required muscle controls and (2) a 12 degree-of-freedom (DOF) knee with elastic foundation contact at the tibiofemoral and patellofemoral articulations for forward dynamic integration. Measured external forces and kinematics were applied as a feedback controller and static optimization attempted to track measured knee flexion angles and electromyographic (EMG) activity. The resulting simulations showed excellent tracking of knee flexion (average RMS error of 2.53 deg) and EMG (muscle activations within ±10% envelopes of normalized measured EMG signals). Simulated tibiofemoral contact forces agreed qualitatively with measured contact forces, but their RMS errors were approximately 25% of the peak measured values. These results demonstrate the potential of a dual-joint modeling approach to predict joint contact forces from kinesiological data measured in the motion laboratory. It is anticipated that errors in the estimation of contact force will be reduced as more accurate subject-specific models of muscles and other soft tissues are developed.

The Influence of Component Alignment and Ligament Properties on Tibiofemoral Contact Forces in Total Knee Replacement.

Science.gov (United States)

Smith, Colin R; Vignos, Michael F; Lenhart, Rachel L; Kaiser, Jarred; Thelen, Darryl G

2016-02-01

The study objective was to investigate the influence of coronal plane alignment and ligament properties on total knee replacement (TKR) contact loads during walking. We created a subject-specific knee model of an 83-year-old male who had an instrumented TKR. The knee model was incorporated into a lower extremity musculoskeletal model and included deformable contact, ligamentous structures, and six degrees-of-freedom (DOF) tibiofemoral and patellofemoral joints. A novel numerical optimization technique was used to simultaneously predict muscle forces, secondary knee kinematics, ligament forces, and joint contact pressures from standard gait analysis data collected on the subject. The nominal knee model predictions of medial, lateral, and total contact forces during gait agreed well with TKR measures, with root-mean-square (rms) errors of 0.23, 0.22, and 0.33 body weight (BW), respectively. Coronal plane component alignment did not affect total knee contact loads, but did alter the medial-lateral load distribution, with 4 deg varus and 4 deg valgus rotations in component alignment inducing +17% and -23% changes in the first peak medial tibiofemoral contact forces, respectively. A Monte Carlo analysis showed that uncertainties in ligament stiffness and reference strains induce ±0.2 BW uncertainty in tibiofemoral force estimates over the gait cycle. Ligament properties had substantial influence on the TKR load distributions, with the medial collateral ligament and iliotibial band (ITB) properties having the largest effects on medial and lateral compartment loading, respectively. The computational framework provides a viable approach for virtually designing TKR components, considering parametric uncertainty and predicting the effects of joint alignment and soft tissue balancing procedures on TKR function during movement.

The Influence of Component Alignment and Ligament Properties on Tibiofemoral Contact Forces in Total Knee Replacement

Science.gov (United States)

Smith, Colin R.; Vignos, Michael F.; Lenhart, Rachel L.; Kaiser, Jarred; Thelen, Darryl G.

2016-01-01

The study objective was to investigate the influence of coronal plane alignment and ligament properties on total knee replacement (TKR) contact loads during walking. We created a subject-specific knee model of an 83-year-old male who had an instrumented TKR. The knee model was incorporated into a lower extremity musculoskeletal model and included deformable contact, ligamentous structures, and six degrees-of-freedom (DOF) tibiofemoral and patellofemoral joints. A novel numerical optimization technique was used to simultaneously predict muscle forces, secondary knee kinematics, ligament forces, and joint contact pressures from standard gait analysis data collected on the subject. The nominal knee model predictions of medial, lateral, and total contact forces during gait agreed well with TKR measures, with root-mean-square (rms) errors of 0.23, 0.22, and 0.33 body weight (BW), respectively. Coronal plane component alignment did not affect total knee contact loads, but did alter the medial–lateral load distribution, with 4 deg varus and 4 deg valgus rotations in component alignment inducing +17% and −23% changes in the first peak medial tibiofemoral contact forces, respectively. A Monte Carlo analysis showed that uncertainties in ligament stiffness and reference strains induce ±0.2 BW uncertainty in tibiofemoral force estimates over the gait cycle. Ligament properties had substantial influence on the TKR load distributions, with the medial collateral ligament and iliotibial band (ITB) properties having the largest effects on medial and lateral compartment loading, respectively. The computational framework provides a viable approach for virtually designing TKR components, considering parametric uncertainty and predicting the effects of joint alignment and soft tissue balancing procedures on TKR function during movement. PMID:26769446

Experimental study on the estimation method of hydrodynamic force acting on floating offshore structures; Futaishiki kaiyo kozobutsu ni kuwawaru ryutairyoku no suiteiho ni kansuru jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Hoshino, K; Kato, S [Ship Research Inst., Tokyo (Japan); Koterayama, W [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

1996-04-10

In the design of various floating offshore structures (FOS), the functionality, safety and amenity of FOSs were examined by estimating responses of FOSs to environmental external forces such as wave, wind and flow. In this paper, the estimation method of drag acting on the whole FOS was established by combining previous study results on hydrodynamic force acting on various bodies such as Reynolds number effect (RNE), 3-D effect (TDE) and interference effect (IE). This hydrodynamic force was also compared with that obtained from the experiment result on a FOS model for TLP to confirm the applicability of this estimation method. The estimation result on the drag coefficient in steady flow by considering RNE, TDE and IE well agreed with experimental one. The drag coefficient acting on FOSs in heaving could be estimated in practically sufficient accuracy by considering drag acting on not columns but only square columns. The estimation result on the drag coefficient acting on FOSs in surging by considering RNE, TDE and IE well agreed with experimental one. 12 refs., 10 figs., 1 tab.

Neutral forces acting on intragenomic variability shape the Escherichia coli regulatory network topology.

Science.gov (United States)

Ruths, Troy; Nakhleh, Luay

2013-05-07

Cis-regulatory networks (CRNs) play a central role in cellular decision making. Like every other biological system, CRNs undergo evolution, which shapes their properties by a combination of adaptive and nonadaptive evolutionary forces. Teasing apart these forces is an important step toward functional analyses of the different components of CRNs, designing regulatory perturbation experiments, and constructing synthetic networks. Although tests of neutrality and selection based on molecular sequence data exist, no such tests are currently available based on CRNs. In this work, we present a unique genotype model of CRNs that is grounded in a genomic context and demonstrate its use in identifying portions of the CRN with properties explainable by neutral evolutionary forces at the system, subsystem, and operon levels. We leverage our model against experimentally derived data from Escherichia coli. The results of this analysis show statistically significant and substantial neutral trends in properties previously identified as adaptive in origin--degree distribution, clustering coefficient, and motifs--within the E. coli CRN. Our model captures the tightly coupled genome-interactome of an organism and enables analyses of how evolutionary events acting at the genome level, such as mutation, and at the population level, such as genetic drift, give rise to neutral patterns that we can quantify in CRNs.

Act No. 732 of December 7, 1988. Act to amend the Act on civil liability for nuclear damage

International Nuclear Information System (INIS)

1988-01-01

This Act amends Act No. 332 of June 19, 1974 on civil liability for nuclear damage, enabling Denmark to ratify the 1982 Protocols to amend the Paris Convention and the Brussels Supplementary Convention as well as the 1988 Joint Protocol relating to the application of the Vienna and the Paris Convention. The 1988 Act raises the nuclear operator's liability from 75 million DKr to 60 million SDRs while cover involving State funds is raised from 120 million units of account to 300 million SDRs. The Act entered into force on July 1, 1989 except for the provision on State funds which becomes effective when the 1982 Protocol amending the Brussels Convention comes into force. (NEA) [fr

Unsteady hydrodynamic forces acting on a hand and its flow field during sculling motion.

Science.gov (United States)

Takagi, Hideki; Shimada, Shohei; Miwa, Takahiro; Kudo, Shigetada; Sanders, Ross; Matsuuchi, Kazuo

2014-12-01

The goal of this research is to clarify the mechanism by which unsteady forces are generated during sculling by a skilled swimmer and thereby to contribute to improving propulsive techniques. We used particle image velocimetry (PIV) to acquire data on the kinematics of the hand during sculling, such as fluid forces and flow field. By investigating the correlations between these data, we expected to find a new propulsion mechanism. The experiment was performed in a flow-controlled water channel. The participant executed sculling motions to remain at a fixed position despite constant water flow. PIV was used to visualize the flow-field cross-section in the plane of hand motion. Moreover, the fluid forces acting on the hand were estimated from pressure distribution measurements performed on the hand and simultaneous three-dimensional motion analysis. By executing the sculling motion, a skilled swimmer produces large unsteady fluid forces when the leading-edge vortex occurs on the dorsal side of the hand and wake capture occurs on the palm side. By using a new approach, we observed interesting unsteady fluid phenomena similar to those of flying insects. The study indicates that it is essential for swimmers to fully exploit vortices. A better understanding of these phenomena might lead to an improvement in sculling techniques. Copyright © 2014 Elsevier B.V. All rights reserved.

Supporting the Future Total Force: A Methodology for Evaluating Potential Air National Guard Mission Assignments

National Research Council Canada - National Science Library

Lynch, Kristin F; Drew, John G; Sleeper, Sally; Williams, William A; Masters, James M; Luangkesorn, Louis; Tripp, Robert S; Lichter, Dahlia S; Roll, Charles R

2007-01-01

... trained, highly experienced personnel with no aircraft to operate and support. The authors develop a methodology to evaluate missions that could be transferred from the active component to the ANG without significant cost to the total force...

VARIABILITY OF FORCED OSCILLATION (SIEMENS SIREGNOST FD-5) MEASUREMENTS OF TOTAL RESPIRATORY RESISTANCE IN PATIENTS AND HEALTHY-SUBJECTS

NARCIS (Netherlands)

GIMENO, F; VANDERWEELE, LT; KOETER, GH; DEMONCHY, JGR; VANALTENA, R

The reproducibility of total respiratory resistance (R(rs)) measured with a simplified forced oscillatory method (Siemens Siregnost FD 5) was measured and compared with that of slow inspiratory vital capacity (IVC) and forced expiratory volume in one second (FEV1). The former technique has the

Fluid dynamic forces acting on a circular tube bundle in cross flow. Proposals of generation condition of vortex-induced vibration and correlation equation of turbulence-induced exciting force

International Nuclear Information System (INIS)

Inada, Fumio; Yoneda, Kimitoshi; Yasuo, Akira; Nishihara, Takashi

2000-01-01

In the circular tube bundle immersed in the crossflow, the exciting force induced by the turbulence and periodically discharged vortices becomes large, and it is necessary to confirm a long-term integrity to the flow induced vibration. In this report, the local fluid exciting force and the correlation length in the direction of tube axis were measured. The exciting force acting on the first row was smaller than that inside the tube bundle, and the exciting force was almost saturated at the third row. As for vortex induced vibration, there could be an influence when a dimensionless frequency was 0.4 or less. When vortex induced vibration did not affect the vibration, a correlation composed of a correlation length and power spectrum density of the local fluid exciting force were proposed, with which we could estimate the amplitude of the vibration. A computer program to estimate the vibration amplitude and maximum stress was made using the flow velocity distribution and the mode of vibration. (author)

Identification of impact force acting on composite laminated plates using the radiated sound measured with microphones

Science.gov (United States)

Atobe, Satoshi; Nonami, Shunsuke; Hu, Ning; Fukunaga, Hisao

2017-09-01

Foreign object impact events are serious threats to composite laminates because impact damage leads to significant degradation of the mechanical properties of the structure. Identification of the location and force history of the impact that was applied to the structure can provide useful information for assessing the structural integrity. This study proposes a method for identifying impact forces acting on CFRP (carbon fiber reinforced plastic) laminated plates on the basis of the sound radiated from the impacted structure. Identification of the impact location and force history is performed using the sound pressure measured with microphones. To devise a method for identifying the impact location from the difference in the arrival times of the sound wave detected with the microphones, the propagation path of the sound wave from the impacted point to the sensor is examined. For the identification of the force history, an experimentally constructed transfer matrix is employed to relate the force history to the corresponding sound pressure. To verify the validity of the proposed method, impact tests are conducted by using a CFRP cross-ply laminate as the specimen, and an impulse hammer as the impactor. The experimental results confirm the validity of the present method for identifying the impact location from the arrival time of the sound wave detected with the microphones. Moreover, the results of force history identification show the feasibility of identifying the force history accurately from the measured sound pressure using the experimental transfer matrix.

75 FR 26956 - Clean Water Act Section 303(d): Availability of Los Angeles Area Lakes Total Maximum Daily Loads...

Science.gov (United States)

2010-05-13

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9146-6] Clean Water Act Section 303(d): Availability of Los...: Notice of availability. SUMMARY: This action announces the availability of EPA proposed total maximum... nutrient, mercury, chlordane, dieldrin, DDT, PCB, and trash impairments pursuant to Clean Water Act Section...

A general method for computing the total solar radiation force on complex spacecraft structures

Science.gov (United States)

Chan, F. K.

1981-01-01

The method circumvents many of the existing difficulties in computational logic presently encountered in the direct analytical or numerical evaluation of the appropriate surface integral. It may be applied to complex spacecraft structures for computing the total force arising from either specular or diffuse reflection or even from non-Lambertian reflection and re-radiation.

Knee Joint Loads and Surrounding Muscle Forces during Stair Ascent in Patients with Total Knee Replacement

Science.gov (United States)

Rasnick, Robert; Standifird, Tyler; Reinbolt, Jeffrey A.; Cates, Harold E.

2016-01-01

Total knee replacement (TKR) is commonly used to correct end-stage knee osteoarthritis. Unfortunately, difficulty with stair climbing often persists and prolongs the challenges of TKR patents. Complete understanding of loading at the knee is of great interest in order to aid patient populations, implant manufacturers, rehabilitation, and future healthcare research. Musculoskeletal modeling and simulation approximates joint loading and corresponding muscle forces during a movement. The purpose of this study was to determine if knee joint loadings following TKR are recovered to the level of healthy individuals, and determine the differences in muscle forces causing those loadings. Data from five healthy and five TKR patients were selected for musculoskeletal simulation. Variables of interest included knee joint reaction forces (JRF) and the corresponding muscle forces. A paired samples t-test was used to detect differences between groups for each variable of interest (pknee extension moment and muscle forces during the loading response phase indicates the presence of deficits in TKR in quadriceps muscle force production during stair ascent. This result combined with greater flexor muscle forces resulted in similar compressive JRF during loading response between groups. PMID:27258086

Fluid-elastic force measurements acting on a tube bundle in two-phase cross flow

International Nuclear Information System (INIS)

Inada, Fumio; Kawamura, Koji; Yasuo, Akira

1996-01-01

Fluid-elastic force acting on a square tube bundle of P/D = 1.47 in air-water two-phase cross flow was measured to investigate the characteristics and to clarify whether the fluid elastic vibration characteristics could be expressed using two-phase mixture characteristics. Measured fluid elastic forces were separated into fluid-elastic force coefficients such as added mass, added stiffness, and added damping coefficient. The added damping coefficient was separated into a two-phase damping and a flow-dependent component as in previous research (Carlucci, 1981 and 1983; Pettigrew, 1994). These coefficients were nondimensionalized with two-phase mixture characteristics such as void fraction, mixture density and mixture velocity, which were obtained using the drift-flux model with consideration given to the model. The result was compared with the result obtained with the homogeneous model. It was found that fluid-elastic force coefficients could be expressed with two-phase flow mixture characteristics very well in the experimental result, and that better result can be derived using the slip model as compared to the homogeneous model. Added two-phase flow, which could be expressed as a function of void fraction, where two-phase damping was nondimensionalized with the relative velocity between the gas and liquid phases used as a reference velocity. Using these, the added stiffness coefficient and flow-dependent component of damping could be expressed very well as a function of nondimensional mixture velocity

Knee Joint Loads and Surrounding Muscle Forces during Stair Ascent in Patients with Total Knee Replacement.

Directory of Open Access Journals (Sweden)

Robert Rasnick

Full Text Available Total knee replacement (TKR is commonly used to correct end-stage knee osteoarthritis. Unfortunately, difficulty with stair climbing often persists and prolongs the challenges of TKR patents. Complete understanding of loading at the knee is of great interest in order to aid patient populations, implant manufacturers, rehabilitation, and future healthcare research. Musculoskeletal modeling and simulation approximates joint loading and corresponding muscle forces during a movement. The purpose of this study was to determine if knee joint loadings following TKR are recovered to the level of healthy individuals, and determine the differences in muscle forces causing those loadings. Data from five healthy and five TKR patients were selected for musculoskeletal simulation. Variables of interest included knee joint reaction forces (JRF and the corresponding muscle forces. A paired samples t-test was used to detect differences between groups for each variable of interest (p<0.05. No differences were observed for peak joint compressive forces between groups. Some muscle force compensatory strategies appear to be present in both the loading and push-off phases. Evidence from knee extension moment and muscle forces during the loading response phase indicates the presence of deficits in TKR in quadriceps muscle force production during stair ascent. This result combined with greater flexor muscle forces resulted in similar compressive JRF during loading response between groups.

Impaction Force Influences Taper-Trunnion Stability in Total Hip Arthroplasty.

Science.gov (United States)

Danoff, Jonathan R; Longaray, Jason; Rajaravivarma, Raga; Gopalakrishnan, Ananthkrishnan; Chen, Antonia F; Hozack, William J

2018-01-31

This study investigated the influence of femoral head impaction force, number of head strikes, the energy sequence of head strikes, and head offset on the strength of the taper-trunnion junction. Thirty titanium-alloy trunnions were mated with 36-mm zero-offset cobalt-chromium femoral heads of corresponding taper angle. A drop tower impacted the head with 2.5J or 8.25J, resulting in 6 kN or 14 kN impaction force, respectively, in a single strike or combinations of 6 kN + 14 kN or 14 kN + 14 kN. In addition, ten 36-mm heads with -5 and +5 offset were impacted with sequential 14 kN + 14 kN strikes. Heads were subsequently disassembled using a screw-driven mechanical testing frame, and peak distraction force was recorded. Femoral head pull-off force was 45% the strike force, and heads struck with a single 14 kN impact showed a pull-off force twice that of the 6 kN group. Two head strikes with the same force did not improve pull-off force for either 6 kN (P = .90) or 14 kN (P = .90). If the forces of the 2 impactions varied, but either impact measured 14 kN, a 51% higher pull-off force was found compared to impactions of either 6 kN or 6 kN + 6 kN. Femoral head offset did not significantly change the pull-off force among -5, 0, and +5 heads (P = .37). Femoral head impaction force influenced femoral head trunnion-taper stability, whereas offset did not affect pull-off force. Multiple head strikes did not add additional stability, as long as a single strike achieved 14 kN force at the mallet-head impactor interface. Insufficient impaction force may lead to inadequate engagement of the trunnion-taper junction. Copyright © 2018 Elsevier Inc. All rights reserved.

Thigh-calf contact parameters for six high knee flexion postures: Onset, maximum angle, total force, contact area, and center of force.

Science.gov (United States)

Kingston, David C; Acker, Stacey M

2018-01-23

In high knee flexion, contact between the posterior thigh and calf is expected to decrease forces on tibiofemoral contact surfaces, therefore, thigh-calf contact needs to be thoroughly characterized to model its effect. This study measured knee angles and intersegmental contact parameters in fifty-eight young healthy participants for six common high flexion postures using motion tracking and a pressure sensor attached to the right thigh. Additionally, we introduced and assessed the reliability of a method for reducing noise in pressure sensor output. Five repetitions of two squatting, two kneeling, and two unilateral kneeling movements were completed. Interactions of posture by sex occurred for thigh-calf and heel-gluteal center of force, and thigh-calf contact area. Center of force in thigh-calf regions was farther from the knee joint center in females, compared to males, during unilateral kneeling (82 and 67 mm respectively) with an inverted relationship in the heel-gluteal region (331 and 345 mm respectively), although caution is advised when generalizing these findings from a young, relatively fit sample to a population level. Contact area was larger in females when compared to males (mean of 155.61 and 137.33 cm 2 across postures). A posture main effect was observed in contact force and sex main effects were present in onset and max angle. Males had earlier onset (121.0°) and lower max angle (147.4°) with onset and max angles having a range between movements of 8° and 3° respectively. There was a substantial total force difference of 139 N between the largest and smallest activity means. Force parameters measured in this study suggest that knee joint contact models need to incorporate activity-specific parameters when estimating loading. Copyright © 2017 Elsevier Ltd. All rights reserved.

Forces acting on particles in a Pelton bucket and similarity considerations for erosion

Science.gov (United States)

Rai, A. K.; Kumar, A.; Staubli, T.

2016-11-01

High sediment transport rates cause severe erosion issues in hydropower plants leading to interruptions in power generation, decrease in efficiency and shutdown for repair and maintenance. For Pelton turbines operating at high head, the issue of erosion is severe, especially in components like buckets, nozzle rings and needles. Goal of the study is to develop erosion focussed guidelines for both designing as well as operating hydropower plants with Pelton runners. In this study, the flow of sediment inside a Pelton bucket with respect to forces acting on solid particles is analysed with an analytical approach by considering different dynamic forces originating from the rotation of the turbine, the curvature of the buckets, and the Coriolis effect. Further, the path of sediment particles and its effect on erosion phenomena are analysed based on the process of separation of different sized sediment particles from streamlines. The data relating to head, power, discharge, number of jet and efficiency of 250 hydropower plants installed all over the world were analysed in this study to find the major factors related to erosion in Pelton turbine bucket. From analysis of different force ratios, it is found that an increase of D/B, i.e. the ratio of pitch circle diameter and bucket width, and/or decrease of specific speed (nq) enhances erosion. As the erosion process depends significantly on nondimensional parameters D/B and nq, these are considered as similarity measures for scaling of the erosion process in the Pelton buckets of various sizes.

Command Clairvoyance: Strategically Transforming AFRC Through Total Force and Leadership

Science.gov (United States)

2012-01-19

backstop for 21st century operations. Lieutenant General Charles Stenner , Chief of the Air Force Reserve, encapsulated this by stating, "The Air Force...and it is a venue that requires the Air Force and AFRC to change in unison, as General Stenner acknowledged: The Air Force is under the same...another generation of TFI savvy leaders. Aligned with General Stenner ‟s previous comments, AFRC needs to foster an “adaptive culture” in order to

Estimation of Tri-Axial Walking Ground Reaction Forces of Left and Right Foot from Total Forces in Real-Life Environments

Directory of Open Access Journals (Sweden)

Erfan Shahabpoor

2018-06-01

Full Text Available Continuous monitoring of natural human gait in real-life environments is essential in many applications including disease monitoring, rehabilitation, and professional sports. Wearable inertial measurement units are successfully used to measure body kinematics in real-life environments and to estimate total walking ground reaction forces GRF(t using equations of motion. However, for inverse dynamics and clinical gait analysis, the GRF(t of each foot is required separately. Using an experimental dataset of 1243 tri-axial separate-foot GRF(t time histories measured by the authors across eight years, this study proposes the ‘Twin Polynomial Method’ (TPM to estimate the tri-axial left and right foot GRF(t signals from the total GRF(t signals. For each gait cycle, TPM fits polynomials of degree five, eight, and nine to the known single-support part of the left and right foot vertical, anterior-posterior, and medial-lateral GRF(t signals, respectively, to extrapolate the unknown double-support parts of the corresponding GRF(t signals. Validation of the proposed method both with force plate measurements (gold standard in the laboratory, and in real-life environment showed a peak-to-peak normalized root mean square error of less than 2.5%, 6.5% and 7.5% for the estimated GRF(t signals in the vertical, anterior-posterior and medial-lateral directions, respectively. These values show considerable improvement compared with the currently available GRF(t decomposition methods in the literature.

Modeling of Dynamic Fluid Forces in Fast Switching Valves

DEFF Research Database (Denmark)

Roemer, Daniel Beck; Johansen, Per; Pedersen, Henrik Clemmensen

2015-01-01

Switching valves experience opposing fluid forces due to movement of the moving member itself, as the surrounding fluid volume must move to accommodate the movement. This movement-induced fluid force may be divided into three main components; the added mass term, the viscous term and the socalled...... history term. For general valve geometries there are no simple solution to either of these terms. During development and design of such switching valves, it is therefore, common practice to use simple models to describe the opposing fluid forces, neglecting all but the viscous term which is determined...... based on shearing areas and venting channels. For fast acting valves the opposing fluid force may retard the valve performance significantly, if appropriate measures are not taken during the valve design. Unsteady Computational Fluid Dynamics (CFD) simulations are available to simulate the total fluid...

Design study of shaft face seal with self-acting lift augmentation. 4: Force balance

Science.gov (United States)

Ludwig, L. P.; Zuk, J.; Johnson, R. L.

1972-01-01

A method for predicting the operating film thickness of self-acting seals is described. The analysis considers a 16.76-cm mean diameter seal that is typical of large gas turbines for aircraft. Four design points were selected to cover a wide range of operation for advanced engines. This operating range covered sliding speeds of 61 to 153 m/sec, sealed pressures of 45 to 217 N/sq cm abs, and gas temperatures of 311 to 977 K. The force balance analysis revealed that the seal operated without contact over the operating range with gas film thicknesses ranging between 0.00046 to 0.00119 cm, and with gas leakage rates between 0.01 to 0.39 scmm.

Countermeasures for Reducing Unsteady Aerodynamic Force Acting on High-Speed Train in Tunnel by Use of Modifications of Train Shapes

Science.gov (United States)

Suzuki, Masahiro; Nakade, Koji; Ido, Atsushi

As the maximum speed of high-speed trains increases, flow-induced vibration of trains in tunnels has become a subject of discussion in Japan. In this paper, we report the result of a study on use of modifications of train shapes as a countermeasure for reducing an unsteady aerodynamic force by on-track tests and a wind tunnel test. First, we conduct a statistical analysis of on-track test data to identify exterior parts of a train which cause the unsteady aerodynamic force. Next, we carry out a wind tunnel test to measure the unsteady aerodynamic force acting on a train in a tunnel and examined train shapes with a particular emphasis on the exterior parts identified by the statistical analysis. The wind tunnel test shows that fins under the car body are effective in reducing the unsteady aerodynamic force. Finally, we test the fins by an on-track test and confirmed its effectiveness.

Assessment of changes in gait parameters and vertical ground reaction forces after total hip arthroplasty

Directory of Open Access Journals (Sweden)

Bhargava P

2007-01-01

Full Text Available The principal objectives of arthroplasty are relief of pain and enhancement of range of motion. Currently, postoperative pain and functional capacity are assessed largely on the basis of subjective evaluation scores. Because of the lack of control inherent in this method it is often difficult to interpret data presented by different observers in the critical evaluation of surgical method, new components and modes of rehabilitation. Gait analysis is a rapid, simple and reliable method to assess functional outcome. This study was undertaken in an effort to evaluate the gait characteristics of patients who underwent arthroplasty, using an Ultraflex gait analyzer. Materials and Methods: The study was based on the assessment of gait and weight-bearing pattern of both hips in patients who underwent total hip replacement and its comparison with an age and sex-matched control group. Twenty subjects of total arthroplasty group having unilateral involvement, operated by posterior approach at our institution with a minimum six-month postoperative period were selected. Control group was age and sex-matched, randomly selected from the general population. Gait analysis was done using Ultraflex gait analyzer. Gait parameters and vertical ground reaction forces assessment was done by measuring the gait cycle properties, step time parameters and VGRF variables. Data of affected limb was compared with unaffected limb as well as control group to assess the weight-bearing pattern. Statistical analysis was done by′t′ test. Results: Frequency is reduced and gait cycle duration increased in total arthroplasty group as compared with control. Step time parameters including Step time, Stance time and Single support time are significantly reduced ( P value < .05 while Double support time and Single swing time are significantly increased ( P value < .05 in the THR group. Forces over each sensor are increased more on the unaffected limb of the THR group as compared to

New US energy policy act in force

International Nuclear Information System (INIS)

Heller, W.

2005-01-01

The United States of America is accused by politicians of the German Red-Green federal government, but also by the EU, of not caring enough about climate protection. This allegation is fueled, above all, by the refusal of the United States to sign the Kyoto Protocol of the UN Climate Framework Convention of 1997. However, the US is not idle in this respect. In late July, the United States together with China, India, Japan, South Korea and Australia agreed on an Asia-Pacific Partnership on Clean Development and Climate. Almost at the same time, on July 29, 2005, after more than five years of debate, the US Congress adopted new energy legislation (A Bill to Ensure Jobs for the Future with Secure and Reliable Energy - the Energy Policy Act of 2005). The holistic aspect in this piece of US legislation covers nearly the whole field of energy policy. The Act encompasses these areas: - energy efficiency, - renewable energies, - oil and natural gas, - clean coal, - nuclear power, - vehicles and fuels, - hydrogen, - electricity, - research and development. With its new Energy Policy Act, the United States has paved the way politically for making energy supply in the world's largest industrialized national securer and safer on a technical basis and less pollutant for the environment and the climate. (orig.)

On the estimation method of hydrodynamic forces acting on a huge floating structure; Choogata futai ni hataraku haryoku ryutairyoku no suiteiho ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kagemoto, H.; Fujino, M.; Zhu, T. [The University of Tokyo, Tokyo (Japan)

1996-12-31

A floating structure such as an international airport is anticipated to have a length of about 5,000 m and a width of about 1,000 m. A singular point method may be used as a method to estimate force that such a floating body is subjected to from waves. In order to derive a solution with practically sufficient accuracy, 1250 elements are required in the length direction and 250 elements in the width direction, or a total of 312,500 elements. Calculating this number of elements should use finally a linear equation system handling complex coefficients comprising 312,500 elements, which would require a huge amount of calculation time. This paper proposes a method to derive solution on wave forces acting on a super-large floating structure or fluid force coefficients such as added mass coefficients and decay coefficients at a practically workable calculation amount and still without degrading the accuracy. The structure was assumed to be a box-shaped structure. Strengths of the singular points to be distributed on each element were assumed to be almost constant except for edges in lateral, oblique and longitudinal waves. Under this assumption, the interior of the floating structure excepting its edges was represented by several large elements to have reduced the number of elements. A calculation method proposed based on this conception was verified of its effectiveness. 2 refs., 25 figs., 3 tabs.

Static magnetic forces and torques in ATLAS

International Nuclear Information System (INIS)

Morozov, N.A.; Samsonov, E.V.; Vorozhtsov, S.B.

1998-01-01

The magnetic forces acting on the various metallic objects around the ATLAS detector, are the subject of the given paper. A system designer could use the information on global forces and torque acting on various components, obtained in this report, to optimize them. The results of force calculations could also serve as additional criteria for the replacement of the magnetic baseline material of various structures by nonmagnetic ones

What forces act in relativistic gyroscope precession?

Science.gov (United States)

Semerák, Oldrich

1996-11-01

The translation of the relativistic motion into the language of forces, proposed by the author (1995, Nuovo Cimento B 110 973), is employed to interpret the gyroscope precession in general relativity. The precession is referred to the comoving Frenet triad built up along the projection of the gyroscope's trajectory onto the 3-space of the local hypersurface-orthogonal observer. The contributions of the centrifugal, the gravitational and the dragging + Coriolis forces are identified respectively with the Thomas, the geodetic, and the gravitomagnetic components of precession. Explicit expressions are given for several simple types of motion in the Kerr (or simpler) field in order to show that the general formulae obtained are not only very simple, but also yield clear results in accord with intuition in concrete situations.

ART Or AGR: Deciphering Which Reserve Program is Best Suited for Today’s Total Force Structure

Science.gov (United States)

2016-02-01

AIR COMMAND AND STAFF COLLEGE AIR UNIVERSITY ART OR AGR: DECIPHERING WHICH RESERVE PROGRAM IS BEST SUITED FOR TODAY’S TOTAL FORCE STRUCTURE...4 ART Program...time workforce, which are the ART and AGR programs, by comparing each and highlighting the differences, advantages and disadvantages they present to

Reserve Components and the National Will: Clauswitz, Total Force Policy and the Strategic Realities of the 21st Century

National Research Council Canada - National Science Library

Reynolds, George

2003-01-01

.... It will also examine the linkage between Prussian military theorist, Carl von Clauswitz's concepts and the formulation of the Abrams Doctrine and Total Force Policy as they apply to the relationship...

Comparisons Between Experimental and Semi-theoretical Cutting Forces of CCS Disc Cutters

Science.gov (United States)

Xia, Yimin; Guo, Ben; Tan, Qing; Zhang, Xuhui; Lan, Hao; Ji, Zhiyong

2018-05-01

This paper focuses on comparisons between the experimental and semi-theoretical forces of CCS disc cutters acting on different rocks. The experimental forces obtained from LCM tests were used to evaluate the prediction accuracy of a semi-theoretical CSM model. The results show that the CSM model reliably predicts the normal forces acting on red sandstone and granite, but underestimates the normal forces acting on marble. Some additional LCM test data from the literature were collected to further explore the ability of the CSM model to predict the normal forces acting on rocks of different strengths. The CSM model underestimates the normal forces acting on soft rocks, semi-hard rocks and hard rocks by approximately 38, 38 and 10%, respectively, but very accurately predicts those acting on very hard and extremely hard rocks. A calibration factor is introduced to modify the normal forces estimated by the CSM model. The overall trend of the calibration factor is characterized by an exponential decrease with increasing rock uniaxial compressive strength. The mean fitting ratios between the normal forces estimated by the modified CSM model and the experimental normal forces acting on soft rocks, semi-hard rocks and hard rocks are 1.076, 0.879 and 1.013, respectively. The results indicate that the prediction accuracy and the reliability of the CSM model have been improved.

Negative Knudsen force on heated microbeams

KAUST Repository

Zhu, Taishan; Ye, Wenjing; Zhang, Jun

2011-01-01

Knudsen force acting on a heated microbeam adjacent to a cold substrate in a rarefied gas is a mechanical force created by unbalanced thermal gradients. The measured force has its direction pointing towards the side with a lower thermal gradient

Hydrodynamic forces on inundated bridge decks

Science.gov (United States)

2009-05-01

The hydrodynamic forces experienced by an inundated bridge deck have great importance in the design of bridges. Specifically, the drag force, lift force, and the moment acting on the bridge deck under various levels of inundation and a range of flow ...

A new method for measuring lift forces acting on an airfoil under dynamic conditions

Energy Technology Data Exchange (ETDEWEB)

Wolken-Moehlmann, Gerrit; Peinke, Joachim [Institute of Physics, University of Oldenburg (Germany)

2008-07-01

Wind turbines operate in a turbulent atmospheric boundary layer and are exposed to strong wind fluctuations in time and space. This can induce the dynamic stall, a phenomenon that causes extra loads. Dynamic stall occurs under fast changes in the angle of attack (AoA) and was determined in detail in helicopter research. But in contrast to helicopter aerodynamics, the changes in the AoA of wind turbine airfoils are in general non-sinusoidal, and thus it seems to be difficult to use these measurements and models. Our goal is to acquire lift data under conditions more comparable to real wind turbines, including non-periodic changes in the AoA. For this purpose a closed test section for our wind tunnel was built. An airfoil with a chord length of 0.2m will be rotated by a stepping motor with angular velocities of up to 300 {sup circle} /s. With a maximum wind velocity of 50m/s, Reynolds numbers of Re=700 000 can be realized. The lift force is determined by the counter forces acting on the wind tunnel walls. These are measured by two lines of 40 pressure sensors with sampling rates up to 2kHz. The results show distinct dynamic stall characteristics. Further experiments with different parameters and foils will give a better insight in dynamic stall and a verification and improvement of existing models.

A magnetic gradient induced force in NMR restricted diffusion experiments

International Nuclear Information System (INIS)

Ghadirian, Bahman; Stait-Gardner, Tim; Castillo, Reynaldo; Price, William S.

2014-01-01

We predict that the phase cancellation of a precessing magnetisation field carried by a diffusing species in a bounded geometry under certain nuclear magnetic resonance pulsed magnetic field gradient sequences results in a small force over typically micrometre length scales. Our calculations reveal that the total magnetisation energy in a pore under the influence of a pulsed gradient will be distance-dependent thus resulting in a force acting on the boundary. It is shown that this effect of the magnetisation of diffusing particles will appear as either an attractive or repulsive force depending on the geometry of the pore and magnetic properties of the material. A detailed analysis is performed for the case of a pulsed gradient spin-echo experiment on parallel planes. It is shown that the force decays exponentially in terms of the spin-spin relaxation. The proof is based on classical electrodynamics. An application of this effect to soft matter is suggested

Dust Transport And Force Equilibria In Magnetized Dusty DC Discharges

International Nuclear Information System (INIS)

Land, Victor; Thomas, Edward Jr.; Williams, Jeremaiah

2005-01-01

We have performed experiments on magnetized dusty Argon DC discharges. Here we report on the characterization of the plasma- and the dustparameters and on the response of the dust particles and the plasma to a change in the magnetic configuration inside the discharge. Finally, we show a case in which the balance of forces acting on the dust particles differs from the classical balance (in which the electrostatic force balances the downward force of gravity). In this case the electrostatic force acts as a downward force on the dust particles. From observations we will argue that the ion drag force might be the force that balances this downward electrostatic force

Estimation of Coriolis Force and Torque Acting on Ares-1

Science.gov (United States)

Mackey, Ryan M.; Kulikov, Igor K.; Smelyanskiy, Vadim; Luchinsky, Dmitry; Orr, Jeb

2011-01-01

A document describes work on the origin of Coriolis force and estimating Coriolis force and torque applied to the Ares-1 vehicle during its ascent, based on an internal ballistics model for a multi-segmented solid rocket booster (SRB).

Error analysis and assessment of unsteady forces acting on a flapping wing micro air vehicle: free flight versus wind-tunnel experimental methods.

Science.gov (United States)

Caetano, J V; Percin, M; van Oudheusden, B W; Remes, B; de Wagter, C; de Croon, G C H E; de Visser, C C

2015-08-20

An accurate knowledge of the unsteady aerodynamic forces acting on a bio-inspired, flapping-wing micro air vehicle (FWMAV) is crucial in the design development and optimization cycle. Two different types of experimental approaches are often used: determination of forces from position data obtained from external optical tracking during free flight, or direct measurements of forces by attaching the FWMAV to a force transducer in a wind-tunnel. This study compares the quality of the forces obtained from both methods as applied to a 17.4 gram FWMAV capable of controlled flight. A comprehensive analysis of various error sources is performed. The effects of different factors, e.g., measurement errors, error propagation, numerical differentiation, filtering frequency selection, and structural eigenmode interference, are assessed. For the forces obtained from free flight experiments it is shown that a data acquisition frequency below 200 Hz and an accuracy in the position measurements lower than ± 0.2 mm may considerably hinder determination of the unsteady forces. In general, the force component parallel to the fuselage determined by the two methods compares well for identical flight conditions; however, a significant difference was observed for the forces along the stroke plane of the wings. This was found to originate from the restrictions applied by the clamp to the dynamic oscillations observed in free flight and from the structural resonance of the clamped FWMAV structure, which generates loads that cannot be distinguished from the external forces. Furthermore, the clamping position was found to have a pronounced influence on the eigenmodes of the structure, and this effect should be taken into account for accurate force measurements.

Tragedy, transformation, and triumph: comparing the factors and forces that led to the adoption of the 1860 Adulteration Act in England and the 1906 Pure Food and Drug Act in the United States.

Science.gov (United States)

London, Jillian

2014-01-01

The 1860 Adulteration Act in England and the 1906 Pure Food and Drug Act in the United States were two of the earliest pieces of legislation to provide generalized regulation of food and drugs on a national scale. While significant scholarly attention has been given to explaining the factors and forces that led to the passage of each Act independent of the other, few books or articles have directly compared the similar individuals and events that led to the adoption of both Acts. This paper attempts to fill that gap. Through a comparative examination, this paper reveals that four main components were key to the national pure food and drug movements in both countries: individuals who crusaded for national adulteration legislation; tragedies that shocked the public into calling for reform; press and publicity that was willing and able to bring the evils of adulteration to the forefront of the public mind; and a transformation of the social, political, and economic systems, which created atmospheres conducive to reform. This paper aims to shed new light on the 1860 Adulteration Act and the 1906 Pure Food and Drug Act--two acts that derive their importance not just from the effect that they directly had on the regulation of food and drugs but also as some of the earliest examples of western governments coming to recognize the need for national regulation to protect the public from harm and coming to embrace their changing role as spearheads of modern regulatory states.

Evaluation of aerodynamic forces acting on oscillating cantilever beams based on the study of the damped flexural vibration of aluminium test samples

Science.gov (United States)

Egorov, A. G.; Kamalutdinov, A. M.; Nuriev, A. N.

2018-05-01

The paper is devoted to study of the aerodynamic forces acting on flat cantilever beams performing flexural vibrations in a viscous fluid. Original method for the force evaluation is presented based on analysis of experimental measurements of a logarithmic decrement of vibrations and relative variation in frequency of duralumin test specimens. The theoretical core of the method is based on the classical theory of bending beam oscillations and quasi-two dimensional model of interaction between a beam and a gas. Using the proposed method, extensive series of experiments for a wide range of oscillations parameters were carried out. The processing of the experimental data allowed to establish the global influence of the aerodynamic effects on beam oscillations and the local force characteristics of each cross-section of the beam in the form of universal functions of dimensionless amplitude and dimensionless frequency of oscillation. The obtained estimates of the drag and added mass forces showed a good correspondence with the available numerical and experimental data practically in the entire range of the investigated parameters.

3D characterization of the forces in optical traps based on counter-propagation beams shaped by a spatial light modulator

DEFF Research Database (Denmark)

Kristensen, M. V.; Lindballe, T.; Kylling, A.

2010-01-01

An experimental characterization of the 3D forces, acting on a trapped polystyrene bead in a counter-propagating beam geometry, is reported. Using a single optical trap with a large working distance (in the BioPhotonics Workstation), we simultaneously measure the transverse and longitudinal...... trapping force constants. Two different methods were used: The Drag force method and the Equipartition method. We show that the counterpropagating beams traps are simple harmonic for small displacements. The force constants reveal a transverse asymmetry as - = 9.7 pN/µm and + = 11.3 pN/µm (at a total laser...... power of 2x35 mW) for displacements in opposite directions. The Equipartition method is limited by mechanical noise and is shown to be applicable only when the total laser power in a single 10 µm counter-propagating trap is below 2x20 mW....

The new Swiss Energy Act

International Nuclear Information System (INIS)

Tami, R.

1999-01-01

The new Swiss Energy Act and the accompanying regulation enable the instructions given in the poll by the electorate in 1990 -- the Energy Article in the Swiss Constitution -- to be implemented. The Energy Act creates the necessary basis for an advanced and sustainable energy policy. It should contribute to a sufficient, broadly based, dependable, economical and environment-friendly energy supply. The Energy Act and the Energy Regulation entered into force on January 1, 1999. (author)

Single acting translational/rotational brake

Science.gov (United States)

Allred, Johnny W. (Inventor); Fleck, Jr., Vincent J. (Inventor)

1996-01-01

A brake system is provided that applies braking forces on surfaces in both the translational and rotational directions using a single acting self-contained actuator that travels with the translational mechanism. The brake engages a mechanical lock and creates a frictional force on the translational structure preventing translation while simultaneously creating a frictional torque that prevents rotation of the vertical support. The system may include serrations on the braking surfaces to provide increased braking forces.

Numerical analysis of hydrodynamic forces acting on vertical lift gates; Analise dos esforcos hidrodinamicas em comportas hidraulicas

Energy Technology Data Exchange (ETDEWEB)

Andrade, Jell Lima de [Mecanica Pesada S.A., Taubate, SP (Brazil); Amorim, Jose Carlos Cesar [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil)]. E-mail: jcamorim@ime.eb.br

1997-07-01

A numerical analysis has been developed for calculating viscous flows controlled by a vertical lift gate and hydrodynamic forces acting on it. The numerical solution is obtained from the incompressible Navier-Stoles equations. The numerical techniques is based on a finite element method. A Poisson equation is derived from the pressure-weighted substitution of the full momentum equations into the continuity equation. Turbulence effects are simulated by a K-{epsilon} turbulence model. The procedure developed here is applied for a vertical lift gate operating in a CESP installation, and the results are compared with available experimental data at various opening positions. Good agreement is obtained for the velocity and pressure distributions. (author)

Ehrenfest force in inhomogeneous magnetic field

International Nuclear Information System (INIS)

Sisakyan, A.N.; Shevchenko, O.Yu.; Samojlov, V.N.

2000-01-01

The Ehrenfest force in an inhomogeneous magnetic field is calculated. It is shown that there exist such (very rare) topologically nontrivial physical situations when the Gauss theorem in its classic formulation fails and, as a consequence, apart from the usual Lorentz force an additional, purely imaginary force acts on the charged particle. This force arises only in inhomogeneous magnetic fields of special configurations, has a purely quantum origin, and disappears in the classical limit

Thermal creep force: analysis and application

OpenAIRE

Wolfe, David M.

2016-01-01

Approved for public release; distribution is unlimited The existence of two motive forces on a Crookes radiometer has complicated the investigation of either force independently. The thermal creep shear force, in particular, has been subject to differing interpretations of the direction in which it acts and its order of magnitude. A horizontal vane radiometer design is provided, which isolates the thermal creep shear force. The horizontal vane radiometer is explored through experiment, kin...

Charge-Spot Model for Electrostatic Forces in Simulation of Fine Particulates

Science.gov (United States)

Walton, Otis R.; Johnson, Scott M.

2010-01-01

The charge-spot technique for modeling the static electric forces acting between charged fine particles entails treating electric charges on individual particles as small sets of discrete point charges, located near their surfaces. This is in contrast to existing models, which assume a single charge per particle. The charge-spot technique more accurately describes the forces, torques, and moments that act on triboelectrically charged particles, especially image-charge forces acting near conducting surfaces. The discrete element method (DEM) simulation uses a truncation range to limit the number of near-neighbor charge spots via a shifted and truncated potential Coulomb interaction. The model can be readily adapted to account for induced dipoles in uncharged particles (and thus dielectrophoretic forces) by allowing two charge spots of opposite signs to be created in response to an external electric field. To account for virtual overlap during contacts, the model can be set to automatically scale down the effective charge in proportion to the amount of virtual overlap of the charge spots. This can be accomplished by mimicking the behavior of two real overlapping spherical charge clouds, or with other approximate forms. The charge-spot method much more closely resembles real non-uniform surface charge distributions that result from tribocharging than simpler approaches, which just assign a single total charge to a particle. With the charge-spot model, a single particle may have a zero net charge, but still have both positive and negative charge spots, which could produce substantial forces on the particle when it is close to other charges, when it is in an external electric field, or when near a conducting surface. Since the charge-spot model can contain any number of charges per particle, can be used with only one or two charge spots per particle for simulating charging from solar wind bombardment, or with several charge spots for simulating triboelectric charging

Medição precisa das forças de aceleração em cabos Precise measurement of acceleration forces acting on cables

Directory of Open Access Journals (Sweden)

Edgar Moraes do Nascimento

1986-10-01

Full Text Available Certos problemas do uso do cinto de segurança ainda não foram resolvidos, sendo importante a determinação precisa das forças nos cabos. Existem vários métodos que, da maneira que são aplicados, são de pouca precisão. Com o objetivo de suspender essa imprecisão são apresentados três métodos e aperfeiçoado um outro de determinação da força exercida no cabo. Um desses métodos aplica-se a países subdesenvolvidos.Certain problems related to the use of safety belts remain unsolved, important among them being the exact determination of forces acting on cables. Various methods of calculation, severely limited because of the way in which they are applied, are presented. Three methods with a view to surpassing these limits are presented and another for the calculation of the forces acting on a cable is perfected. One of these methods is applicable in developing countries.

Microscopic derivation of the force on a dielectric fluid in an electromagnetic field

International Nuclear Information System (INIS)

Lai, H.M.; Suen, W.M.; Young, K.

1982-01-01

The force acting on a Clausius-Mossotti fluid in an electromagnetic field is evaluated microscopically. Owing to the modification of the two-particle density by the electric field, an additional mechanical force Δf/sup( M/) is found. When this is added to the electrical force f/sup( E/), the total force in the static case becomes identical to that deduced macroscopically by Helmholtz. The analysis is extended to various time-dependent cases, and it is pointed out that Δf/sup( M/) essentially assumes its static value on time scales longer than T/sub c/, the relaxation time of the two-particle density, but is otherwise negligibly small. Thus Peierls's theory of the momentum of light is valid only for pulses much shorter than T/sub c/; the necessary correction due to Δf/sup( M/) in other cases is given and discussed

Repulsive Casimir-Polder forces from cosmic strings

International Nuclear Information System (INIS)

Saharian, A.A.; Kotanjyan, A.S.

2011-01-01

We investigate the Casimir-Polder force acting on a polarizable microparticle in the geometry of a straight cosmic string. In order to develop this analysis we evaluate the electromagnetic field Green tensor on the imaginary frequency axis. The expression for the Casimir-Polder force is derived in the general case of anisotropic polarizability. In dependence on the eigenvalues for the polarizability tensor and of the orientation of its principal axes, the Casimir-Polder force can be either repulsive or attractive. Moreover, there are situations where the force changes the sign with separation. We show that for an isotropic polarizability tensor the force is always repulsive. At large separations between the microparticle and the string, the force varies inversely with the fifth power of the distance. In the non-retarded regime, corresponding to separations smaller than the relevant transition wavelengths, the force decays with the inverse fourth power of the distance. In the case of anisotropic polarizability, the dependence of the Casimir-Polder potential on the orientation of the polarizability tensor principal axes also leads to a moment of force acting on the particle. (orig.)

Random three-dimensional jammed packings of elastic shells acting as force sensors

Science.gov (United States)

Jose, Jissy; van Blaaderen, Alfons; Imhof, Arnout

2016-06-01

In a jammed solid of granular particles, the applied stress is in-homogeneously distributed within the packing. A full experimental characterization requires measurement of all the interparticle forces, but so far such measurements are limited to a few systems in two and even fewer in three dimensions. Particles with the topology of (elastic) shells are good local force sensors as relatively large deformations of the shells result from relatively small forces. We recently introduced such fluorescent shells as a model granular system in which force distributions can be determined in three dimensions using confocal microscopy and quantitative image analysis. An interesting aspect about these shells that differentiates them from other soft deformable particles is their buckling behavior at higher compression. This leads to deformations that do not conserve the inner volume of the particle. Here we use this system to accurately measure the contact forces in a three-dimensional packing of shells subjected to a static anisotropic compression and to shear. At small deformations forces are linear, however, for a buckled contact, the restoring force is related to the amount of deformation by a square root law, as follows from the theory of elasticity of shells. Near the unjamming-jamming transition (point J ), we found the probability distribution of the interparticle forces P (f ) to decay nearly exponentially at large forces, with little evidence of long-range force chains in the packings. As the packing density is increased, the tail of the distribution was found to crossover to a Gaussian, in line with other experimental and simulation studies. Under a small shear strain, up to 0.216, applied at an extremely low shear rate, we observed a shear-induced anisotropy in both the pair correlation function and contact force network; however, no appreciable change was seen in the number of contacts per particle.

Facial expressions and speech acts: experimental evidences on the role of the upper face as an illocutionary force indicating device in language comprehension.

Science.gov (United States)

Domaneschi, Filippo; Passarelli, Marcello; Chiorri, Carlo

2017-08-01

Language scientists have broadly addressed the problem of explaining how language users recognize the kind of speech act performed by a speaker uttering a sentence in a particular context. They have done so by investigating the role played by the illocutionary force indicating devices (IFIDs), i.e., all linguistic elements that indicate the illocutionary force of an utterance. The present work takes a first step in the direction of an experimental investigation of non-verbal IFIDs because it investigates the role played by facial expressions and, in particular, of upper-face action units (AUs) in the comprehension of three basic types of illocutionary force: assertions, questions, and orders. The results from a pilot experiment on production and two comprehension experiments showed that (1) certain upper-face AUs seem to constitute non-verbal signals that contribute to the understanding of the illocutionary force of questions and orders; (2) assertions are not expected to be marked by any upper-face AU; (3) some upper-face AUs can be associated, with different degrees of compatibility, with both questions and orders.

Induced forces in the gravitational field

International Nuclear Information System (INIS)

Voracek, P.

1979-01-01

In this paper the expression for the magnitude of the so-called induced force, acting on a mass particle, is deduced. The origin of this force is causally connected to the increase of the rest mass of the particle in the gravitational field. (orig.)

Force measuring valve assemblies, systems including such valve assemblies and related methods

Science.gov (United States)

DeWall, Kevin George [Pocatello, ID; Garcia, Humberto Enrique [Idaho Falls, ID; McKellar, Michael George [Idaho Falls, ID

2012-04-17

Methods of evaluating a fluid condition may include stroking a valve member and measuring a force acting on the valve member during the stroke. Methods of evaluating a fluid condition may include measuring a force acting on a valve member in the presence of fluid flow over a period of time and evaluating at least one of the frequency of changes in the measured force over the period of time and the magnitude of the changes in the measured force over the period of time to identify the presence of an anomaly in a fluid flow and, optionally, its estimated location. Methods of evaluating a valve condition may include directing a fluid flow through a valve while stroking a valve member, measuring a force acting on the valve member during the stroke, and comparing the measured force to a reference force. Valve assemblies and related systems are also disclosed.

PLANNING OF IMPLANTO‐PROSTHETIC STRUCTURES IN TOTAL EDENTATION ACCORDING TO BIOMECHANICAL CRITERIA

Directory of Open Access Journals (Sweden)

N. VASILE

2013-07-01

Full Text Available Scope of the study: Analysis of the biomechanical aspects of the implanto‐prosthetic structures for planning the treatment in cases of total edentation.Materials and method: The study was performed in the Clinics of Prosthetics and Oral Implantology, Military Emergency Hospital of Sibiu, on a group of mandibularly totally edentated patients. Planning of the implanto‐pros‐ thetic treatment had in view the peculiarities of total man‐ dibular edentation and observance of the biomechanical principles. Selection of the type of occlusion restoration considered the presence of parafunctions and the nature of the antagonistic arch. Special attention was paid to the direction and intensity of the forces acting in the region of the future prosthetic work. When bruxism was manifested, its preimplantary removal was compulsory.Results and discussion: In fixed prosthetic restaurati‐ ons applied on implants, distribuition of forces obviously depend on the quality of osteo‐acceptance, as well, and also on the elasticity degree of the prosthetic work. In the case of mobilized prosthetic restorations supported on implants, rigidization of implants from the anterior region of the mandible may be obtained by means of a bar. In decreasing order of their elasticity, the materials employed are: acrylate, composites, noble and seminoble alloys, other metals, ceramics. Ceramics confers maximum stability to implants, yet without redeeming the forces. For amortizing the forces and for a progressive charging of the implants, it is recommended that the first (temporary prosthetic restorations should be made of either acrylate or compo‐ sites.Conclusions. Observance of the occlusological princi‐ ples in cases of occlusal reconstruction represents the determining element which assures the osteo‐acceptance of implants and the integrity of prosthetic restaurations.

The Energy Act 1983

International Nuclear Information System (INIS)

1983-01-01

Part II of This Act came into force on 1 September 1983 and is concerned with nuclear installations. Its main purpose is to amend the Nuclear Installations Act 1965 to give effect to the provisions of two Protocols amending the Paris Convention on nuclear third party liability and the Brussels Convention Supplementary to the Paris Convention respectively. The principal effect of these modifications is to increase the sums available to meet claims for nuclear damage. The United Kingdom is a Party to both Conventions and the provisions of the 1983 Act will enable it to ratify the Protocols. (NEA) [fr

Calculation of the total potential between two deformed heavy ion nuclei using the Monte Carlo method and M3Y nucleon-nucleon forces

International Nuclear Information System (INIS)

Ghodsi, O. N.; Zanganeh, V.

2009-01-01

In the current study, a simulation technique has been employed to calculate the total potential between two deformed nuclei. It has been shown that this simulation technique is an efficient one for calculating the total potential for all possible orientations between the symmetry axes of the interacting nuclei using the realistic nuclear matter density and the M3Y nucleon-nucleon effective forces. The analysis of the results obtained for the 48 Ca+ 238 U, 46 Ti+ 46 Ti, and 27 Al+ 70 Ge reactions reveal that considering the density dependent effects in the M3Y forces causes the nuclear potential to drop by an amount of 0.4 MeV.

32 CFR 806b.4 - Privacy Act complaints.

Science.gov (United States)

2010-07-01

... be identified, the local Privacy Act officer will assume these duties. Issues that cannot be resolved... 32 National Defense 6 2010-07-01 2010-07-01 false Privacy Act complaints. 806b.4 Section 806b.4 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE ADMINISTRATION PRIVACY ACT...

Macroscopic QED in linearly responding media and a Lorentz-Force approach to dispersion forces

Energy Technology Data Exchange (ETDEWEB)

Raabe, Christian

2008-07-08

In this thesis, a very general quantization scheme for the macroscopic electromagnetic field in arbitrary linearly responding media is presented. It offers a unified approach to QED in such media. Applying the quantization scheme, a theory of the dispersion forces on the basis of the Lorentz force is developed. By regarding the dispersion force as the (ground-state or thermal-state) expectation value of the Lorentz force that acts on appropriately defined charge and current densities, Casimir, Casimir-Polder, and van der Waals forces are united in a very natural way that makes transparent their common physical basis. Application of the theory to planar structures yields generalizations of well-known Lifschitz and Casimir-type formulas. (orig.)

Macroscopic QED in linearly responding media and a Lorentz-Force approach to dispersion forces

International Nuclear Information System (INIS)

Raabe, Christian

2008-01-01

In this thesis, a very general quantization scheme for the macroscopic electromagnetic field in arbitrary linearly responding media is presented. It offers a unified approach to QED in such media. Applying the quantization scheme, a theory of the dispersion forces on the basis of the Lorentz force is developed. By regarding the dispersion force as the (ground-state or thermal-state) expectation value of the Lorentz force that acts on appropriately defined charge and current densities, Casimir, Casimir-Polder, and van der Waals forces are united in a very natural way that makes transparent their common physical basis. Application of the theory to planar structures yields generalizations of well-known Lifschitz and Casimir-type formulas. (orig.)

Wind and Current Forces Acting on Canadian Forces Ships During Tug Operations

Science.gov (United States)

2002-11-01

McTaggart and Sav- age [1] describe model tests conducted on a generic frigate model to determine wind forces influencing ship capsize. Van Manen and van ...Fn will be 0.06. Based on data presented by van Manen and van Oossanen [2], the fric- tional resistance coefficient will be approximately 0.002 and...Conference on Stability of Ships and Ocean Vehicles (Melbourne, Florida, 1994). 2. J.D. van Manen and P. van Oossanen, Principles of Naval Architecture, Volume

Novel parallel plate condenser for single particle electrostatic force measurements in atomic force microscope

KAUST Repository

Kwek, Jin Wang

2011-07-01

A combination of small parallel plate condenser with Indium Tin Oxide (ITO) glass slides as electrodes and an atomic force microscope (AFM) is used to characterize the electrostatic behavior of single glass bead microparticles (105-150 μm) glued to the AFM cantilever. This novel setup allows measurements of the electrostatic forces acting on a particle in an applied electrical field to be performed in ambient air conditions. By varying the position of the microparticle between the electrodes and the strength of the applied electric field, the relative contributions of the particle net charge, induced and image charges were investigated. When the microparticle is positioned in the middle of the electrodes, the force acting on the microparticle was linear with the applied electric field and proportional to the microparticle net charge. At distances close to the bottom electrode, the force follows a parabolic relationship with the applied electric field reflecting the contributions of induced and image charges. The method can be used for the rapid evaluation of the charging and polarizability properties of the microparticle as well as an alternative to the conventional Faraday\\'s pail technique. © 2011 Elsevier B.V.

Children's Typically-Perceived-Situations of Force and No Force in the Context of Australia and Korea

Science.gov (United States)

Joung, Yong Jae; Gunstone, Richard

2010-08-01

Typically-Perceived-Situation (TPS) refers to the situation rising spontaneously in an individual's mind when she/he first thinks of a phenomenon or concept. The purpose of this study is to go well beyond the many studies that describe conceptions of force and explore children's TPS of "force is acting on a thing" and "force is not acting on a thing", and to do this in the differing contexts of Australia and Korea. Data were collected by drawings and written explanations from 145 Grade 6 Australian children and 150 Grade 6 Korean children. These data showed some significant differences between the Australian children's and Korean children's TPSs. For example, considering the whole context of children's TPS, the contexts of "someone pushes or pulls something" and "someone/something is floating in the air or not moving because there is no gravity" were the most frequent ones, as a "force" and as a "no force" situation respectively, in the case of Australian children, while "a sort of energy is provided into someone/something and they can be active/working" and "a sort of energy is not provided into someone/something and they cannot be active/working", were most frequent in the case of Korean children. These differences are very likely the consequence of different everyday meanings for the word "force" in the two cultures. In addition, it appears that these children's TPS affect their judgement of "force" and "no force".

Wind Forces on Container Ships

DEFF Research Database (Denmark)

Andersen, Ingrid Marie Vincent

2012-01-01

An investigation of the wind forces acting on a 9,000+ TEU container ship has been carried out through a series of wind tunnel tests. It was investigated how the wind forces depend on the container configuration on the deck using a 1:450 scale model and a series of appropriate container...... are presented as nondimensional coefficients. It is concluded, that the measured forces and moment depend on the container configuration on deck, and the results may provide a general idea of how the magnitude of the wind forces is affected by a given container stacking configuration on a similar container ship....

77 FR 30871 - Implementing the Prison Rape Elimination Act

Science.gov (United States)

2012-05-23

...--Implementing the Prison Rape Elimination Act Proclamation 8823--Armed Forces Day, 2012 #0; #0; #0; Presidential... Prison Rape Elimination Act Memorandum for the Heads of Executive Departments and Agencies Sexual... Rape Elimination Act of 2003 (PREA) was enacted with bipartisan support and established a ``zero...

Act of 21 February 1963, Stb. 82, concerning the release of nuclear energy and the use of radioactive materials and of devices emitting ionizing radiations (Nuclear Energy Act) as amended by the Act of 30 June 1967, Stb. 337, and the Act of 8 May 1974, Stb. 291

International Nuclear Information System (INIS)

1963-01-01

This basic Act governs all nuclear activities in the Netherlands and determines the Government's competence and the obligations of those involved in the nuclear field. It establishes definitions and sets up bodies to advise the Government in the different nuclear sectors and covers nuclear installations, fissionable materials, ores, radioactive materials, radiation-emitting devices and their licensing. It was brought into force progressively by decrees made in implementation of its provisions, which lay down detailed regulations for the activity concerned. The chapters of the Act not yet in force were brought into operation on 1 January 1970 by the Nuclear Energy Act (Implantation) Decree of 12 November 1969. (NEA) [fr

Modeling forces in high-temperature superconductors

International Nuclear Information System (INIS)

Turner, L. R.; Foster, M. W.

1997-01-01

We have developed a simple model that uses computed shielding currents to determine the forces acting on a high-temperature superconductor (HTS). The model has been applied to measurements of the force between HTS and permanent magnets (PM). Results show the expected hysteretic variation of force as the HTS moves first toward and then away from a permanent magnet, including the reversal of the sign of the force. Optimization of the shielding currents is carried out through a simulated annealing algorithm in a C++ program that repeatedly calls a commercial electromagnetic software code. Agreement with measured forces is encouraging

Environmental Assessment for Proposed Security Forces Operations Facility, Buckley Air Force Base, Colorado

National Research Council Canada - National Science Library

Meyer, Elizabeth; Myklebust, Jessica; Denier, James; Christner, Jennifer; Fontaine, Kathyrn

2006-01-01

The United States Air Force (USAF) has prepared this EA in accordance with the National Environmental Policy Act to evaluate the potential environmental and social impacts from the construction and operation of the proposed SFOF...

Crossflow-induced vibrations of tube banks: hydrodynamic forces and mathematical models

International Nuclear Information System (INIS)

Chen, S.S.

1977-01-01

The objective of this paper is to present a method of analysis for the hydrodynamic forces acting on tube banks and a mathematical model for multiple tubes and multiple excitation mechanisms incorporating tube/fluid coupling. The hydrodynamic forces acting on tube banks are analyzed using the two dimensional potential flow theory

Casimir-lifshitz force out of thermal equilibrium and asymptotic nonadditivity

NARCIS (Netherlands)

Antezza, Mauro; Pitaevskii, Lev P.; Stringari, Sandro; Svetovoy, Vitaly

2006-01-01

We investigate the force acting between two parallel plates held at different temperatures. The force reproduces, as limiting cases, the well-known Casimir-Lifshitz surface-surface force at thermal equilibrium and the surface-atom force out of thermal equilibrium recently derived by M. Antezza et

Atomic Energy Authority Act 1986

International Nuclear Information System (INIS)

1986-01-01

Under this Act the UKAEA is given power to borrow so that it can finance its capital expenditure programme, and will undertake a debt to the Secretary of State for Energy representing its assets. Power is given for the Government to guarantee such borrowing. The UKAEA has been organised financially on the basis of a trading fund. The Act came into force on 1 April 1986. (NEA) [fr

Effect of fatigue on force production and force application technique during repeated sprints.

Science.gov (United States)

Morin, Jean-Benoit; Samozino, Pierre; Edouard, Pascal; Tomazin, Katja

2011-10-13

We investigated the changes in the technical ability of force application/orientation against the ground vs. the physical capability of total force production after a multiple-set repeated sprints series. Twelve male physical education students familiar with sprint running performed four sets of five 6-s sprints (24s of passive rest between sprints, 3min between sets). Sprints were performed from a standing start on an instrumented treadmill, allowing the computation of vertical (F(V)), net horizontal (F(H)) and total (F(Tot)) ground reaction forces for each step. Furthermore, the ratio of forces was calculated as RF=F(H)F(Tot)(-1), and the index of force application technique (D(RF)) representing the decrement in RF with increase in speed was computed as the slope of the linear RF-speed relationship. Changes between pre- (first two sprints) and post-fatigue (last two sprints) were tested using paired t-tests. Performance decreased significantly (e.g. top speed decreased by 15.7±5.4%; Pmultiple-set repeated sprint series, both the total force production capability and the technical ability to apply force effectively against the ground are altered, the latter to a larger extent than the former. Copyright © 2011 Elsevier Ltd. All rights reserved.

Methods for estimating the labour force insured by the Ontario Workplace Safety and Insurance Board: 1990-2000.

Science.gov (United States)

Smith, Peter M; Mustard, Cameron A; Payne, Jennifer I

2004-01-01

This paper presents a methodology for estimating the size and composition of the Ontario labour force eligible for coverage under the Ontario Workplace Safety & Insurance Act (WSIA). Using customized tabulations from Statistics Canada's Labour Force Survey (LFS), we made adjustments for self-employment, unemployment, part-time employment and employment in specific industrial sectors excluded from insurance coverage under the WSIA. Each adjustment to the LFS reduced the estimates of the insured labour force relative to the total Ontario labour force. These estimates were then developed for major occupational and industrial groups stratified by gender. Additional estimates created to test assumptions used in the methodology produced similar results. The methods described in this paper advance those previously used to estimate the insured labour force, providing researchers with a useful tool to describe trends in the rate of injury across differing occupational, industrial and gender groups in Ontario.

Propellant Slosh Force and Mass Measurement

Directory of Open Access Journals (Sweden)

Andrew Hunt

2018-01-01

Full Text Available We have used electrical capacitance tomography (ECT to instrument a demonstration tank containing kerosene and have successfully demonstrated that ECT can, in real time, (i measure propellant mass to better than 1% of total in a range of gravity fields, (ii image propellant distribution, and (iii accurately track propellant centre of mass (CoM. We have shown that the ability to track CoM enables the determination of slosh forces, and we argue that this will result in disruptive changes in a propellant tank design and use in a spacecraft. Ground testing together with real-time slosh force data will allow an improved tank design to minimize and mitigate slosh forces, while at the same time keeping the tank mass to a minimum. Fully instrumented Smart Tanks will be able to provide force vector inputs to a spacecraft inertial navigation system; this in turn will (i eliminate or reduce navigational errors, (ii reduce wait time for uncertain slosh settling, since actual slosh forces will be known, and (iii simplify slosh control hardware, hence reducing overall mass. ECT may be well suited to space borne liquid measurement applications. Measurements are independent of and unaffected by orientation or levels of g. The electronics and sensor arrays can be low in mass, and critically, the technique does not dissipate heat into the propellant, which makes it intrinsically safe and suitable for cryogenic liquids. Because of the limitations of operating in earth-bound gravity, it has not been possible to check the exact numerical accuracy of the slosh force acting on the vessel. We are therefore in the process of undertaking a further project to (i build a prototype integrated “Smart Tank for Space”, (ii undertake slosh tests in zero or microgravity, (iii develop the system for commercial ground testing, and (iv qualify ECT for use in space.

Properties of pseudo magnetism acting between bodies

Directory of Open Access Journals (Sweden)

Anish Deva

Full Text Available A non-contact force has been found to be always acting between two bodies kept close to each other in different media. The properties of the force are different as compared to other non-contact forces such as gravitation and electrostatics, as was shown in our previous work. The aim of this paper is to find how the force behaves when two objects are brought near each other, one being completely immersed in the medium and the other kept just outside. The magnitude of the force in each medium has been calculated through experiments and then compared with each other. The discrepancies obtained between these magnitudes (10−5 N in water and 10−6 N in engine oil and the varied oscillation patterns (amplitude and frequency obtained from graphs have shown that the force behaves differently with different media. In general, the frequency of the force has been found to be of the order 10−2 Hz. The behaviour has also been found to depend on the nature of the material and shape of the object. This correlation has been ascertained by using a Gauss meter to measure the force acting between two objects and also that of an individual object. The polarity of the force i.e. whether attractive or repulsive, has been found to vary across the length of the objects and graphs have been plotted to demonstrate this property. Keywords: Non-contact force, Medium, Magnetism, Gravitation, Frequency

Force acting on a spherical bubble rising through a quiescent liquid

International Nuclear Information System (INIS)

Takagi, Shu; Matsumoto, Yoichiro

1996-01-01

The direct numerical simulation is performed on the spherical bubble unsteadily rising through a quiescent liquid. The method is based on a finite-volume solution of the equations on an orthogonal curvilinear coordinate system. The calculations are performed for a bubble rising through a clean liquid and contaminated one. Following the former experimental results, the tangential stress free condition is given for a clean bubble, and no-slip condition for contaminated one. The numerical results are compared with those of the model equation of the translational motion of the bubble, which is often used in numerical models of a bubbly flow. The steady drag, added mass and history terms are checked up by the comparison. It is revealed that the history force effect is negligible for a bubble rising through the clean liquid beyond Re=O(50). From the numerical point of view, the fact that the history force is negligible is quite important, because it reduces the calculation time and memory for a bubbly flow model. For a contaminated bubble, history force effect is not negligible even though the Reynolds number is high enough. It is found that the expression of the history force by Basset kernel gives an over-estimation of the history force for the bubble rising at moderate Reynolds number. This error becomes larger with increasing Reynolds number and it reduces the accuracy to calculate the bubble motion by the model equation. (author)

TOTAL FORCE INTEGRATION: PROVIDING STABILITY FOR CITIZEN SOLDIERS IN AN EVER CHANGING AIR FORCE

Science.gov (United States)

2016-10-01

specifically called for achieving a better work - life balance and “leveraging the best talents of our Guard, Reserve, and civilian teams.”88 Taking...paper will offer unique scenarios (Let it Be, Nowhere Man, The Long and Winding Road, and We Can Work It Out) which balance mission readiness against...entire Air Force airlift mission, resulting in substantial stressors on civilian careers and family life , which has always been the cornerstone of

A brief history of the Coriolis force

NARCIS (Netherlands)

Gerkema, T.; Gostiaux, L.

2012-01-01

In 1835, Gustave Coriolis derived the expression of a force acting in rotating systems, now known as the Coriolis force. His work was inspired by rotating devices such as waterwheels. However, the onerotating device that has always been with us is the Earth itself. Indeed, the earliest studies on

SPEECH ACT IN ADVERTISING LANGUAGE OF 3 PROVIDER MOBILE PHONE PRODUCT

Directory of Open Access Journals (Sweden)

Suhartini Syukri

2016-04-01

Full Text Available This study is an analysis of selected commercial advertisement on product consumed relates to the 3 provider of mobile phone in Indonesian context. Consumers are generally believed to be active and skeptical users of information. Then, the speech act can contribute how successfulness the advertisers in persuading them. There are three kinds of act; they are locutionary act, illocutionary act and perlocutionary act. A perlocutionary act, the act that is produced as a consequences or effect of uttering a specific locution, what is brought about or achieved by saying something, in this case, the effects may be predictable by the conventional status of most illocutions, but may be force of their speech act. Using the qualitative method of research, the writers try to analyze the kinds of illocutionary forces and perlocutionary acts that occur in the advertisement through socio-pragmatic analysis. The result shows that the illocutionary acts commonly equal to the persuasive and informative as well as the advertisement goal, then the perlocutionary effects will be related to the hearers themselves.

Mathematical modelling and numerical simulation of forces in milling process

Science.gov (United States)

Turai, Bhanu Murthy; Satish, Cherukuvada; Prakash Marimuthu, K.

2018-04-01

Machining of the material by milling induces forces, which act on the work piece material, tool and which in turn act on the machining tool. The forces involved in milling process can be quantified, mathematical models help to predict these forces. A lot of research has been carried out in this area in the past few decades. The current research aims at developing a mathematical model to predict forces at different levels which arise machining of Aluminium6061 alloy. Finite element analysis was used to develop a FE model to predict the cutting forces. Simulation was done for varying cutting conditions. Different experiments was designed using Taguchi method. A L9 orthogonal array was designed and the output was measure for the different experiments. The same was used to develop the mathematical model.

Absolute measurement of the total ion-drag force on a single plasma-confined microparticle at the void edge under microgravity conditions

NARCIS (Netherlands)

Beckers, J.; Trienekens, D.J.M.; Kroesen, G.M.W.

2013-01-01

We present an absolute measurement of the total ion-drag force on one single microparticle at the edge of the dust free region in low pressure complex plasmas: the void. In order to do so, the particle confinement position was monitored as a function of the gas pressure for two particle sizes under

Atomic Energy Act 1989

International Nuclear Information System (INIS)

1989-05-01

This Act, which entered into force on 1 september 1989, contains a series of provisions dealing with different subjects: increase of public financing for British Nuclear Fuels plc, amendment of the Nuclear Installations Act 1965 regarding the powers of the Health and Safety Executive to recover expenses directly from nuclear operators and obligation of the UKAEA to take out insurance or other financial security to cover its liability and finally, measures to enable the UK to ratify the IAEA Convention on Assistance in Case of a Nuclear Accident or Radiological Emergency [fr

Biomechanical Effects of Posterior Condylar Offset and Posterior Tibial Slope on Quadriceps Force and Joint Contact Forces in Posterior-Stabilized Total Knee Arthroplasty

Directory of Open Access Journals (Sweden)

Kyoung-Tak Kang

2017-01-01

Full Text Available This study aimed to determine the biomechanical effect of the posterior condylar offset (PCO and posterior tibial slope (PTS in posterior-stabilized (PS fixed-bearing total knee arthroplasty (TKA. We developed ±1, ±2, and ±3 mm PCO models in the posterior direction and −3°, 0°, 3°, and 6° PTS models using a previously validated FE model. The influence of changes in the PCO and PTS on the biomechanical effects under deep-knee-bend loading was investigated. The contact stress on the PE insert increased by 14% and decreased by 7% on average as the PCO increased and decreased, respectively, compared to the neutral position. In addition, the contact stress on post in PE insert increased by 18% on average as PTS increased from −3° to 6°. However, the contact stress on the patellar button decreased by 11% on average as PTS increased from −3° to 6° in all different PCO cases. The quadriceps force decreased by 14% as PTS increased from −3° to 6° in all PCO models. The same trend was found in patellar tendon force. Changes in PCO had adverse biomechanical effects whereas PTS increase had positive biomechanical effects. However, excessive PTS should be avoided to prevent knee instability and subsequent failure.

Analysing a Relationship Between Wheel Wear and Cutting Forces During Diamond Grinding

Directory of Open Access Journals (Sweden)

M. A. Shavva

2014-01-01

Full Text Available In diamond grinding cutting forces affect the quality of the machined surface. We can estimate a wear rate of the diamond wheel by the magnitude of the forces and promptly resort to the restoration of its cutting properties. To solve this problem it is necessary to define a relationship between grinding wheel wear and cutting forces. There was no this dependence found in the sources of literature.The forces acting on a single worn diamond grain are considered to find the relationship between wheel wear and cutting forces. The main forces acting on the diamond grain are such as a reaction force of machining material, a frictional force over a worn place of the grain, and a total pressure on the contact surface of the grain and machining material. According to calculation results, in grinding the cutting forces are proportional to the hardness of machining material, and depend on the grain wear, as well as on the process operation conditions.The paper presents a technique for calculating the number of cutting (active grains per unit surface of diamond wheel to determine a total cutting force in grinding. The number of cutting grains depends on the properties of diamond wheel and on the operation conditions of grinding process.During grinding a total cutting force is calculated through the single grain cutting force, the number of cutting grains per unit surface of the grinding wheel and the contact area between the wheel and the work piece. Theoretical calculation of the forces is based on the condition that protrusions of all cutting grains are identical and all grains have a maximum wear, i.e. maximum worn place of grain.Calculations based on proposed theoretical formulas are compared with the calculations from the empirical formulas given in the literature. Varying the operation conditions of grinding makes the comparison. Convergence of results in the range of 5-20% is regarded as acceptable.On the BMSTU base flat diamond grinding of tungsten

Labor Force

Science.gov (United States)

Occupational Outlook Quarterly, 2010

2010-01-01

The labor force is the number of people aged 16 or older who are either working or looking for work. It does not include active-duty military personnel or institutionalized people, such as prison inmates. Quantifying this total supply of labor is a way of determining how big the economy can get. Labor force participation rates vary significantly…

Variable Thumb Moment Arm Modeling and Thumb-Tip Force Production of a Human-Like Robotic Hand.

Science.gov (United States)

Niehues, Taylor D; Deshpande, Ashish D

2017-10-01

The anatomically correct testbed (ACT) hand mechanically simulates the musculoskeletal structure of the fingers and thumb of the human hand. In this work, we analyze the muscle moment arms (MAs) and thumb-tip force vectors in the ACT thumb in order to compare the ACT thumb's mechanical structure to the human thumb. Motion data are used to determine joint angle-dependent MA models, and thumb-tip three-dimensional (3D) force vectors are experimentally analyzed when forces are applied to individual muscles. Results are presented for both a nominal ACT thumb model designed to match human MAs and an adjusted model that more closely replicates human-like thumb-tip forces. The results confirm that the ACT thumb is capable of faithfully representing human musculoskeletal structure and muscle functionality. Using the ACT hand as a physical simulation platform allows us to gain a better understanding of the underlying biomechanical and neuromuscular properties of the human hand to ultimately inform the design and control of robotic and prosthetic hands.

The Carriage of goods by Sea Act 1971 (Commencement, Order 1977)

International Nuclear Information System (INIS)

1977-01-01

This Order (S.I. No 981) brought into force the Carriage of Goods by Sea Act 1971 giving effect at internal level to the 1968 Protocol to the International Convention on Certain Rules of Law relating to Bills of Lading 1924 (the Hague Rules). The 1971 Act introduces an amendment to the Nuclear Installations Act 1965 which lays down, as does the Paris Convention, that none of its provisions shall affect the operation of international transport agreements in force in the United Kingdom, and in particular, the Hague Rules. As of now, and in accordance with the 1968 Protocol, the Nuclear Installations Act 1965 no longer reserves application of the Hague Rules. (NEA) [fr

Atomic Energy Authority (Weapons Group) Act 1973

International Nuclear Information System (INIS)

1973-01-01

This Act, which came into force on 6th March 1973 and modified Section 2 of the Atomic Energy Authority Act 1954 in respect of the Authority's power to do work on explosive nuclear devices, made provision for the transfer to the Secretary of State for Defence of the Weapons Group of the Atomic Energy Authority. (NEA) [fr

The Social Support Act: the story so far

NARCIS (Netherlands)

Mirjam de Klerk; Rob Gilsing; Joost Timmermans

2010-01-01

Original title: Op weg met de Wmo. The Social Support Act (Wet maatschappelijke ondersteuning - Wmo) came into force in the Netherlands on 1 January 2007. The aim of the Act is to promote people's social and life skills and ability to participate, and to strengthen social cohesion and quality

Numerical and experimental study of the effect of the induced electric potential in Lorentz force velocimetry

Science.gov (United States)

Hernández, Daniel; Boeck, Thomas; Karcher, Christian; Wondrak, Thomas

2018-01-01

Lorentz force velocimetry (LFV) is a contactless velocity measurement technique for electrically conducting fluids. When a liquid metal or a molten glass flows through an externally applied magnetic field, eddy currents and a flow-braking force are generated inside the liquid. This force is proportional to the velocity or flow rate of the fluid and, due to Newton’s third law, a force of the same magnitude but in opposite direction acts on the source of the applied magnetic field which in our case are permanent magnets. According to Ohm’s law for moving conductors at low magnetic Reynolds numbers, an electric potential is induced which ensures charge conservation. In this paper, we analyze the contribution of the induced electric potential to the total Lorentz force by considering two different scenarios: conducting walls of finite thickness and aspect ratio variation of the cross-section of the flow. In both the cases, the force component generated by the electric potential is always in the opposite direction to the total Lorentz force. This force component is sensitive to the electric boundary conditions of the flow of which insulating and perfectly conducting walls are the two limiting cases. In the latter case, the overall electric resistance of the system is minimized, resulting in a considerable increase in the measured Lorentz force. Additionally, this force originating from the electric potential also decays when the aspect ratio of the cross-section of the flow is changed. Hence, the sensitivity of the measurement technique is enhanced by either increasing wall conductivity or optimizing the aspect ratio of the cross-section of the flow.

Against acts of nuclear terrorism

International Nuclear Information System (INIS)

Heller, W.

2007-01-01

The Act on the International Convention of the United Nations of April 13, 2005 on Combating Acts of Nuclear Terrorism was promulgated in the German Federal Gazette and entered into force one day later. The Convention expresses the deep concern about the worldwide escalation of all kinds and manifestations of acts of terrorism. What was true in April 2005 (the year the UN convention was adopted) is even more true today. At the same time, however, the Convention recognizes the right of all nations to develop and use nuclear power for peaceful purposes, acknowledging their justified interest in the possible benefits of the peaceful uses of nuclear power. As the Convention was signed in German still during the term of office of the Red-Green government, this passage is a remarkable acceptance of the realities of the world and past peaceful uses of nuclear power in Germany. Whether or not the convention will become an effective instrument to be used against acts of nuclear terrorism and threats depends on its entering into force after deposition of 22 ratification documents, and on as many states as possible acceding to it. Irrespective of these aspects, action in the spirit of the Convention should be taken now, criminal law should be adapted, and international cooperation should be improved and strengthened. (orig.)

Size Dependent Orientation of Knudsen Force

KAUST Repository

Zhu, Taishan

2012-03-03

Knudsen force acting on a heated microbeam adjacent to a cold substrate in a rarefied gas is a mechanical force created by unbalanced thermal gradients. The measured force has its direction pointing towards the side with a lower thermal gradient and its magnitude vanishes in both continuum and free-molecule limits. In our previous study, negative Knudsen forces were discovered at the high Knudsen regime before diminishing in the free-molecule limit. Such a phenomenon was however not observed in the experiment. In this paper, the existence of such a negative Knudsen force is further confirmed using both numerical simulation and theoretical analysis. The asymptotic order of the Knudsen force near the collisionless limit is analyzed and the analytical expression of its leading term is provided, from which approaches for the enhancement of negative Knudsen forces are proposed. Copyright © 2012 by ASME.

Origin of Knudsen forces on heated microbeams

KAUST Repository

Zhu, Taishan

2010-09-09

The presented work probes the fundamentals of Knudsen forces. Using the direct simulation Monte Carlo (DSMC) method, the flows induced by temperature inhomogeneity within a representative configuration and the Knudsen force acting on a heated microbeam are captured as functions of Knudsen number in the entire flow regime. Both flow strength and Knudsen force peak in the transition regime and negative Knudsen force absent in experimental data is observed. The mechanisms of the thermally induced flows and Knudsen forces are studied. It has been found that thermal edge flow is the main driven source for the formation of the Knudsen force on microbeams and domain configuration plays an important role in the process.

High-Pressure Hot-Gas Self-Acting Floating Ring Shaft Seal for Liquid Rocket Turbopumps. [tapered bore seals

Science.gov (United States)

Burcham, R. E.; Diamond, W. A.

1980-01-01

Design analysis, detail design, fabrication, and experimental evaluation was performed on two self acting floating ring shaft seals for a rocket engine turbopump high pressure 24132500 n/sq m (3500 psig) hot gas 533 K 9500 F) high speed 3142 rad/sec (30000 rmp) turbine. The initial design used Rayleigh step hydrodynamic lift pads to assist in centering the seal ring with minimum rubbing contact. The final design used a convergent tapered bore to provide hydrostatic centering force. The Rayleigh step design was tested for 107 starts and 4.52 hours total. The leakage was satisfactory; however, the design was not acceptable due to excessive wear caused by inadequate centering force and failure of the sealing dam caused by erosion damage. The tapered bore design was tested for 370 starts and 15.93 hours total. Satisfactory performance for the required life of 7.5 hours per seal was successfully demonstrated.

On the generalized potential of inertial forces

International Nuclear Information System (INIS)

Siboni, S

2009-01-01

The generalized potential of the inertial forces acting on a holonomic system in an accelerated reference frame is derived in a way which admits a simple physical interpretation. It is shown that the generalized potential refers to all the inertial forces and, apart from the very special case of a uniformly rotating frame, it is impossible to distinguish a contribution to only the Coriolis force and a contribution pertaining to the residual, velocity-independent fictitious forces. Such an approach to the determination of the generalized potential of inertial forces may be helpful in introducing the topic of the generalized potential to advanced undergraduate and graduate students

Dynamic analysis of fast-acting solenoid valves using finite element method

International Nuclear Information System (INIS)

Kwon, Ki Tae; Han, Hwa Taik

2001-01-01

It is intended to develop an algorithm for dynamic simulation of fast-acting solenoid valves. The coupled equations of the electric, magnetic, and mechanical systems should be solved simultaneously in a transient nonlinear manner. The transient nonlinear electromagnetic field is analyzed by the Finite Element Method (FEM), which is coupled with nonlinear electronic circuitry. The dynamic movement of the solenoid valve is analyzed at every time step from the force balances acting on the plunger, which include the electromagnetic force calculated from the finite element analysis as well as the elastic force by a spring and the hydrodynamic pressure force along the flow passage. Dynamic responses of the solenoid valves predicted by this algorithm agree well the experimental results including bouncing effects

76 FR 53421 - Privacy Act of 1974; System of Records

Science.gov (United States)

2011-08-26

..., Air Force Privacy Act Office, Office of Warfighting Integration and Chief Information Officer, ATTN...: Name, signatures, personal contact information, individual's employer and institutional, organizational..., Historical Products, Services, and Requirements; Air Force Instruction 84-105, Organizational Lineage, Honors...

No 592 - Radiation Act

International Nuclear Information System (INIS)

1991-01-01

This Act will enter into force on 1 January 1992. The scope of the Act is extensive as, in addition to ionizing radiation, it will also apply to activities involving exposure to natural radiation and non-ionizing radiation. Its purpose is to prevent and restrict harmful effects to health resulting from radiation. The basic principles of the Act are that the practice involving radiation should be justified; radiation protection should be optimized; and radiation doses should be as low as reasonably achievable. Licensed organisations using radiation will be responsible for the safety of the activity involving exposure to radiation and for having available the appropriate expertise to this effect. The required so-called safety licence provides the regulatory control to ensure that radiation is used sensibly, that the equipment and shields are technically acceptable and the operating personnel is competent, and that the radioactive waste is dealt with appropriately. The Radiation Act will also apply to nuclear activities within the scope of the 1987 Nuclear Energy Act [fr

Self-acting shaft seals

Science.gov (United States)

Ludwig, L. P.

1978-01-01

Self-acting seals are described in detail. The mathematical models for obtaining a seal force balance and the equilibrium operating film thickness are outlined. Particular attention is given to primary ring response (seal vibration) to rotating seat face runout. This response analysis reveals three different vibration models with secondary seal friction being an important parameter. Leakage flow inlet pressure drop and affects of axisymmetric sealing face deformations are discussed. Experimental data on self-acting face seals operating under simulated gas turbine conditions are given. Also a spiral groove seal design operated to 244 m/sec (800 ft/sec) is described.

Light-induced attractive force between two metal bodies separated by a subwavelength slit

International Nuclear Information System (INIS)

Nesterov, Vladimir; Frumin, Leonid

2011-01-01

A novel light-induced attractive force which acts as a force with negative light pressure has been revealed. The force arises by the interaction of plasmon polaritons which are excited at the surface of metal when a transverse magnetic mode propagates through a subwavelength slit between two metal bodies. The estimation of the repulsive force acting on the metal walls of the slit in the case of subwavelength TE mode propagation along the slit is presented. The explicit analytical expressions of light-induced forces between two macroscopic metal bodies or films separated by a subwavelength slit have been derived. These forces could be used to manipulate metallic macro-, micro- and nano-objects in vacuum or in a dielectric medium. Estimations of these light-induced forces show that the forces are sufficient for measurements and practical applications

Merchant shipping (Safety Convention) Act 1977

International Nuclear Information System (INIS)

1977-01-01

When this Act comes into force, it will enable the United Kingdom to ratify and to give effect to the 1974 International Convention for the Safety of Life at Sea (the SOLAS Convention) which replaces the SOLAS Convention of 1960. Under the Act, the Secretary of State may make such rules as he considers appropriate regarding ships provided with nuclear power plants in accordance with Chapter VIII of the Annex to the 1974 Convention and to Recommendations attached to it, dealing with nuclear ships, and insofar as those provisions have not been implemented by the Merchant Shipping Acts 1894 to 1974. (NEA) [fr

Radioactive Material (Road Transport) Act 1991

International Nuclear Information System (INIS)

1991-01-01

This Act came into force on 27 August 1991. It replaces earlier legislation dating from 1948 and enables the United Kingdom to give effect to the International Atomic Energy Agency's (IAEA) latest recommended Regulations for the Safe Transport of Radioactive Material. The new Act clarifies and extends the power of the Secretary of State to make regulations regarding, among other things, the design, labelling, handling, transport and delivery of packages containing radioactive material and the placarding of vehicles transporting such packages. The Act gives the Secretary of State the power to appoint inspectors to assist him in enforcing the regulations. (NEA)

Supporting the Future Total Force: A Methodology for Evaluating Potential Air National Guard Mission Assignments

National Research Council Canada - National Science Library

Lynch, Kristin F; Drew, John G; Sleeper, Sally; Williams, William A; Masters, James M; Luangkesorn, Louis; Tripp, Robert S; Lichter, Dahlia S; Roll, Charles R

2007-01-01

Manpower end-strength reductions of active duty personnel in the U.S. Air Force are making it more difficult to support the air and space expeditionary force construct using current force employment practices...

Ponderomotive Forces in Cosmos

Science.gov (United States)

Lundin, R.; Guglielmi, A.

2006-12-01

This review is devoted to ponderomotive forces and their importance for the acceleration of charged particles by electromagnetic waves in space plasmas. Ponderomotive forces constitute time-averaged nonlinear forces acting on a media in the presence of oscillating electromagnetic fields. Ponderomotive forces represent a useful analytical tool to describe plasma acceleration. Oscillating electromagnetic fields are also related with dissipative processes, such as heating of particles. Dissipative processes are, however, left outside these discussions. The focus will be entirely on the (conservative) ponderomotive forces acting in space plasmas. The review consists of seven sections. In Section 1, we explain the rational for using the auxiliary ponderomotive forces instead of the fundamental Lorentz force for the study of particle motions in oscillating fields. In Section 2, we present the Abraham, Miller, Lundin-Hultqvist and Barlow ponderomotive forces, and the Bolotovsky-Serov ponderomotive drift. The hydrodynamic, quasi-hydrodynamic, and ‘`test-particle’' approaches are used for the study of ponderomotive wave-particle interaction. The problems of self-consistency and regularization are discussed in Section 3. The model of static balance of forces (Section 4) exemplifies the interplay between thermal, gravitational and ponderomotive forces, but it also introduces a set of useful definitions, dimensionless parameters, etc. We analyze the Alfvén and ion cyclotron waves in static limit with emphasis on the specific distinction between traveling and standing waves. Particular attention has been given to the impact of traveling Alfvén waves on the steady state anabatic wind that blows over the polar regions (Section~5). We demonstrate the existence of a wave-induced cold anabatic wind. We also show that, at a critical point, the ponderomotive acceleration of the wind is a factor of 3 greater than the thermal acceleration. Section 6 demonstrates various

Optical force rectifiers based on PT-symmetric metasurfaces

Science.gov (United States)

Alaee, Rasoul; Gurlek, Burak; Christensen, Johan; Kadic, Muamer

2018-05-01

We introduce here the concept of optical force rectifier based on parity-time symmetric metasurfaces. Directly linked to the properties of non-Hermitian systems engineered by balanced loss and gain constituents, we show that light can exert asymmetric pulling or pushing forces on metasurfaces depending on the direction of the impinging light. This generates a complete force rectification in the vicinity of the exceptional point. Our findings have the potential to spark the design of applications in optical manipulation where the forces, strictly speaking, act unidirectionally.

32 CFR 806.29 - Administrative processing of Air Force FOIA requests.

Science.gov (United States)

2010-07-01

... FORCE ADMINISTRATION AIR FORCE FREEDOM OF INFORMATION ACT PROGRAM § 806.29 Administrative processing of... information systems by processing a simple request/providing a response in the electronic format requested.../service/a nongovernment source (Exemption 4), records are part of the Air Force's decision-making process...

32 CFR 806.27 - Samples of Air Force FOIA processing documents.

Science.gov (United States)

2010-07-01

... ADMINISTRATION AIR FORCE FREEDOM OF INFORMATION ACT PROGRAM § 806.27 Samples of Air Force FOIA processing... determination within 20 workdays, we have instituted multitrack processing of requests. Based on the information... source; responsive records were part of the Air Force's decision-making process, and the prerelease...

System modelling of a lateral force microscope

International Nuclear Information System (INIS)

Michal, Guillaume; Lu, Cheng; Kiet Tieu, A

2008-01-01

To quantitatively analyse lateral force microscope measurements one needs to develop a model able to relate the photodiode signal to the force acting on the tip apex. In this paper we focus on the modelling of the interaction between the cantilever and the optical chain. The laser beam is discretized by a set of rays which propagates in the system. The analytical equation of a single ray's position on the optical sensor is presented as a function of the reflection's state on top of the cantilever. We use a finite element analysis on the cantilever to connect the optical model with the force acting on the tip apex. A first-order approximation of the constitutive equations are derived along with a definition of the system's crosstalk. Finally, the model is used to analytically simulate the 'wedge method' in the presence of crosstalk in 2D. The analysis shows how the torsion loop and torsion offset signals are affected by the crosstalk.

The Swedish Insurance Contracts Act 2005 – an overview

OpenAIRE

Hjalmarsson, Johanna

2008-01-01

On 1 January 2006 a new Insurance Contracts Act (Försäkringsavtalslag (SFS 2005:104)) entered into force in Sweden, replacing the Insurance Contracts Act 1927 and the Consumer Insurance Act 1980. The Act is in many ways a modern and interesting product and merits an introduction in English, in the context of the current process of reform undertaken by the Law Commissions of England & Wales and Scotland as well as in the context of expected European initiatives for insurance contract law r...

Self-acting and hydrodynamic shaft seals

Science.gov (United States)

Ludwig, L. P.

1973-01-01

Self-acting and hydrodynamic seals are described. The analytical procedures are outlined for obtaining a seal force balance and the operating film thickness. Particular attention is given to primary ring response (seal vibration) to rotating seat face runout. This response analysis revealed three different vibration modes. Proposed applications of self-acting seals in gas turbine engines and in rocket vehicle turbopumps are described. Also experimental data on self-acting face seals operating under simulated gas turbine conditions are given; these data show the feasibility of operating the seal at conditions of 345 newtons per square centimeter (500 psi) and 152 meters per second (500 ft/sec) sliding speed.

The Radiation Protection Act

International Nuclear Information System (INIS)

Persson, L.

1989-01-01

The new Radiation Protection Act (1988:220) entered into force in Sweden on July 1st, 1988. This book presents the Act as well as certain regulations connected to it. As previously, the main responsibility for public radiation protection will rest with one central radiation protection authority. According to the 1988 Act, the general obligations with regard to radiation protection will place a greater responsibility than in the past on persons carrying out activities involving radiation. Under the act, it is possible to adjust the licensing and supervisory procedures to the level of danger of the radiation source and the need for adequate competence, etc. The Act recognises standardised approval procedures combined with technical regulations for areas where the risks are well known. The Act contains several rules providing for more effective supervision. The supervising authority may in particular decide on the necessary regulations and prohibitions for each individual case. The possibilities of using penal provisions have been extended and a rule on the mandatory execution of orders has been introduced. The Ordinance on Radiation Protection (1988:293) designates the National Institute of Radiation Protection (SSI) as the central authority referred to in the Radiation Protection Act. The book also gives a historic review of radiation protection laws in Sweden, lists regulations issued by SSI and presents explanations of radiation effects and international norms in the area. (author)

Uncertainties in forces extracted from non-contact atomic force microscopy measurements by fitting of long-range background forces

Directory of Open Access Journals (Sweden)

Adam Sweetman

2014-04-01

Full Text Available In principle, non-contact atomic force microscopy (NC-AFM now readily allows for the measurement of forces with sub-nanonewton precision on the atomic scale. In practice, however, the extraction of the often desired ‘short-range’ force from the experimental observable (frequency shift is often far from trivial. In most cases there is a significant contribution to the total tip–sample force due to non-site-specific van der Waals and electrostatic forces. Typically, the contribution from these forces must be removed before the results of the experiment can be successfully interpreted, often by comparison to density functional theory calculations. In this paper we compare the ‘on-minus-off’ method for extracting site-specific forces to a commonly used extrapolation method modelling the long-range forces using a simple power law. By examining the behaviour of the fitting method in the case of two radically different interaction potentials we show that significant uncertainties in the final extracted forces may result from use of the extrapolation method.

The Key Driving Forces for Geo-Economic Relationships between China and ASEAN Countries

Directory of Open Access Journals (Sweden)

Shufang Wang

2017-12-01

Full Text Available With the rise of China and the implementation of the “21st Century Maritime Silk Road” strategy, research on geo-economics between China and ASEAN (Association of Southeast Asian Nations countries has become increasingly important. Current studies mainly focus on influencing factors, while there is little consideration about how these influencing factors act on geo-economic relationships. Therefore, this paper explores the key driving forces for geo-economic relationships between China and ASEAN countries by use of the structural equation modeling based on Partial Lease Squares. There are three main findings: (1 Economic factors have the greatest impact on geo-economic relationships and the total path effect is 0.778. Geo-location, geopolitics and geo-culture act on geo-economic relationships directly and indirectly. Their total path effects are 0.731, 0.645 and 0.513, respectively. (2 Indirect effects of geo-location, geopolitics and geo-culture impacting geo-economic relationships are far greater than direct effects. Geo-culture, in particular, has a vital mediating effect on geo-economic relationships. (3 Economic drivers promote geo-economic relationships through market, industrial policy, technical, network and benefit-sharing mechanisms. Political drivers improve geo-economic relationships through cooperation, negotiation, coordination and institutional mechanisms. Cultural drivers enhance geo-economic relationships through transmission mechanism. Location drivers facilitate geo-economic relationships through selection mechanism. We provide new insights on the geo-economic relationships through quantitative analysis and enrich the existing literature by revealing the key driving forces and mechanisms for geo-economic relationships.

Effectively Managing the Air Force Enterprise Architecture

National Research Council Canada - National Science Library

Sharkey, Jamie P

2005-01-01

The Air Force is developing and implementing an enterprise architecture to meet the Clinger-Cohen Act's requirement that all federal agencies use an architecture to guide their information technology (IT) investments...

The Röntgen interaction and forces on dipoles in time-modulated optical fields

Science.gov (United States)

Sonnleitner, Matthias; Barnett, Stephen M.

2017-12-01

The Röntgen term is an often neglected contribution to the interaction between an atom and an electromagnetic field in the electric dipole approximation. In this work we discuss how this interaction term leads to a difference between the kinetic and canonical momentum of an atom which, in turn, leads to surprising radiation forces acting on the atom. We use a number of examples to explore the main features of this interaction, namely forces acting against the expected dipole force or accelerations perpendicular to the beam propagation axis.

Electromagnetic force analysis on the stator and rotor windings of a superconducting generator

International Nuclear Information System (INIS)

Colovini, L.; Martinelli, G.; Morini, A.

1985-01-01

The determination of values and distribution of the forces acting on the components of a superconducting generator is important when designing the machine, particularly in the choice of materials. The paper analyses the electromagnetic forces acting on the field and armature windings; for this purpose, with reference to the preliminary design of a two-pole 300 MVA superconducting generator, a two-dimensional analytical method set up by the authors is utilized to calculate the forces on the windings under steady state operation and results are compared with those obtained by means of a numerical method

Polymer translocation under a pulling force: Scaling arguments and threshold forces

Science.gov (United States)

Menais, Timothée

2018-02-01

DNA translocation through nanopores is one of the most promising strategies for next-generation sequencing technologies. Most experimental and numerical works have focused on polymer translocation biased by electrophoresis, where a pulling force acts on the polymer within the nanopore. An alternative strategy, however, is emerging, which uses optical or magnetic tweezers. In this case, the pulling force is exerted directly at one end of the polymer, which strongly modifies the translocation process. In this paper, we report numerical simulations of both linear and structured (mimicking DNA) polymer models, simple enough to allow for a statistical treatment of the pore structure effects on the translocation time probability distributions. Based on extremely extended computer simulation data, we (i) propose scaling arguments for an extension of the predicted translocation times τ ˜N2F-1 over the moderate forces range and (ii) analyze the effect of pore size and polymer structuration on translocation times τ .

Lithuania’s Balancing Act

Directory of Open Access Journals (Sweden)

Šlekys Deividas

2017-12-01

Full Text Available Since regaining independence in 1990 and creating its regular armed forces, Lithuania has had to do a balancing act. It has had to balance between different approaches of state defence, military structure, collective and national defence. Due to events in Ukraine Lithuania had to reconfigure this balance. The Russian threat forced to emphasize strategy of territorial defence, which altogether required tying up forces and enlarging its numbers by bringing back conscription, substantially increased defence budget, followed by higher tempo and scale in procurement and training. However, Lithuania has managed to maintain its activity and participation in international military operations and political initiatives. Its recent contributions have led to an assumption that its participation in various military missions in the future will not diminish, quite the opposite. Increasing the framework of cooperation in terms of defence and security initiatives will involve Lithuania more deeply and will require further contributions.

Effect of polarization force on the Jeans instability of self-gravitating dusty plasma

International Nuclear Information System (INIS)

Prajapati, R.P.

2011-01-01

The effect of polarization force acting on massive charged dust grains is investigated analytically on the Jeans instability of self-gravitating dusty plasma. The gravitational force acting on the massive negatively charged interstellar dust grains are considered in presence of both electrical and polarization forces. The basic equations of the problem are formulated and a general dispersion relation is obtained using plane wave approximation in low frequency wave mode. The effect of polarization force in the dispersion relation of the problem, condition of the Jeans instability and expression of the critical Jeans wave number is examined. The unstable growing modes due to self-gravitational force are studied in the situation when polarization force on the dust grain exceeds over the electrical force in magnitude. It is observed that the polarization force increases the growth rate of the system. -- Highlights: → Jeans instability of gravitating dusty plasma with polarization force is investigated. → The fundamental Jeans instability criterion is modified due to polarization effect. → The critical Jeans length decreases due to increase in polarization force. → Polarization force destabilizes the unstable Jeans mode. → The collapsing of interstellar dusty cloud is discussed.

Self-force on dislocation segments in anisotropic crystals

International Nuclear Information System (INIS)

Fitzgerald, S P; Aubry, S

2010-01-01

A dislocation segment in a crystal experiences a 'self-force', by virtue of the orientation dependence of its elastic energy. If the crystal is elastically isotropic, this force is manifested as a couple acting to rotate the segment toward the lower energy of the pure screw orientation (i.e. acting to align the dislocation line with its Burgers vector). If the crystal is anisotropic, there are additional contributions to the couple, arising from the more complex energy landscape of the lattice itself. These effects can strongly influence the dynamic evolution of dislocation networks, and via their governing role in dislocation multiplication phenomena, control plastic flow in metals. In this paper we develop a model for dislocation self-forces in a general anisotropic crystal, and briefly consider the technologically important example of α-iron, which becomes increasingly anisotropic as the temperature approaches that of the α-γ phase transition at 912 0 C.

Shape-dependent orientation of thermophoretic forces in microsystems

KAUST Repository

Li, Qi

2013-09-24

It is generally acknowledged that the direction of the thermophoretic force acting on microparticles is largely determined by the imposed temperature gradient, and the shape of the microparticle has little influence on its direction. We show that one type of thermophoretic force, emerged due to the advent of microfabrication techniques, is highly sensitive to object shape, and it is feasible to tune force orientation via proper shape design. We reveal the underlying mechanism by an asymptotic analysis of the Boltzmann equation and point out the reason why the classical thermophoretic force is insensitive to the particle shape, but the force in microsystems is. The discovered phenomenon could find its applications in methods for microparticle manipulation and separation.

Repulsive Casimir force at zero and finite temperature

International Nuclear Information System (INIS)

Lim, S C; Teo, L P

2009-01-01

We study the zero and finite temperature Casimir force acting on a perfectly conducting piston with arbitrary cross section moving inside a closed cylinder with infinitely permeable walls. We show that at any temperature, the Casimir force always tends to move the piston away from the walls and toward its equilibrium position. In the case of a rectangular piston, exact expressions for the Casimir force are derived. In the high-temperature regime, we show that the leading term of the Casimir force is linear in temperature and therefore the Casimir force has a classical limit. Due to duality, all these results also hold for an infinitely permeable piston moving inside a closed cylinder with perfectly conducting walls.

Shape-dependent orientation of thermophoretic forces in microsystems

KAUST Repository

Li, Qi; Liang, Tengfei; Ye, Wenjing

2013-01-01

It is generally acknowledged that the direction of the thermophoretic force acting on microparticles is largely determined by the imposed temperature gradient, and the shape of the microparticle has little influence on its direction. We show that one type of thermophoretic force, emerged due to the advent of microfabrication techniques, is highly sensitive to object shape, and it is feasible to tune force orientation via proper shape design. We reveal the underlying mechanism by an asymptotic analysis of the Boltzmann equation and point out the reason why the classical thermophoretic force is insensitive to the particle shape, but the force in microsystems is. The discovered phenomenon could find its applications in methods for microparticle manipulation and separation.

Negative Knudsen force on heated microbeams

KAUST Repository

Zhu, Taishan

2011-11-18

Knudsen force acting on a heated microbeam adjacent to a cold substrate in a rarefied gas is a mechanical force created by unbalanced thermal gradients. The measured force has its direction pointing towards the side with a lower thermal gradient and its magnitude vanishes in both continuum and free-molecule limits. In our previous study, negative Knudsen forces were discovered at the high Knudsen regime before diminishing in the free-molecule limit. Such a phenomenon was, however, neither observed in experiment [A. Passian et al., Phys. Rev. Lett. 90, 124503 (2003)], nor captured in the latest numerical study [J. Nabeth et al., Phys. Rev. E 83, 066306 (2011)]. In this paper, the existence of such a negative Knudsen force is further confirmed using both numerical simulation and theoretical analysis. The asymptotic order of the Knudsen force near the collisionless limit is analyzed and the analytical expression of its leading term is provided, from which approaches for the enhancement of negative Knudsen forces are proposed. The discovered phenomenon could find its applications in novel mechanisms for pressure sensing and actuation.

Drafting force majeure clauses in natural gas purchase/sale contracts -- the practicalities

International Nuclear Information System (INIS)

Reschke, D. N.; Campbell, L. M.

1999-01-01

The place of 'force majeure' provisions, in gas purchase/sale contracts is discussed. This issue, not normally considered to be significant in gas purchase/sale contracts, became a matter of intense interest in the aftermath of the Atcor Ltd v. Continental Energy Marketing case when the trial court, as well as the Alberta Court of Appeals, strongly criticized the wording of the force majeure clause in the contract as containing a 'choice of words that assured litigation'. Force majeure, simply stated, refers to acts of God, (lightning, earthquakes, storms, floods, etc) and acts of war. It is inserted in contracts to limit the liability of parties to the contract in the event of inability to perform due to any of the above acts of God, or acts of war. In this particular case, the force majeure cause included, in addition to the above, a long list of other causes such as strikes, lockouts or other industrial disturbances, insurrections, riots, epidemics, landslides, fires, washouts, explosions of or accidents to plant, machinery or lines of pipe, well blowouts, and pipeline repairs and reconditioning. The trial court found the drafting of the clause archaic, circumventing clarity, and drearily lengthy. In view of the court's decision it is clear that more thought has to go into drafting force majeure decisions in the future. Accordingly, this paper attempts to discuss practical issues of drafting force majeure clauses that clearly reflect the parties' intentions and expectations so that costly litigations might be avoided, or if litigation is unavoidable, to at least have the outcome of such litigation be more predictable. The focus of the discussion is on legal interpretation issues, forms of gas contract force majeure provisions- events and consequences, and standardization of force majeure provisions. It is recommended that the drafter of such clauses should always keep in mind the potential impact that the strict construction and commercial reasonability concepts

76 FR 2113 - Sunshine Act; Notice of Meeting

Science.gov (United States)

2011-01-12

... public. MATTERS TO BE CONSIDERED: Open Session 1. Announcement of Notation Votes, and 2. Human Trafficking and Forced Labor--Invited Panelists Note: In accordance with the Sunshine Act, the meeting will be...

Analysis of Dynamic Inertia Forces at Main Bearing of Ship Reciprocating Engines

Directory of Open Access Journals (Sweden)

F. Louhenapessy Louhenapessy,

2010-11-01

Full Text Available During operation, a ship reciprocating engine will vibrate due to the force resulting from the cycle movement of the dynamic components. Soon or later, the vibration will cause wear of engine components. Therefore, the cause of vibration should be early identified so that the propagation of wear can be anticipated. The study modeled the ship reciprocating engine as a two stroke engine, and analyzed one of the causes of the engine vibration, i.e. the force acting on main bearing, using a numerical simulation. An experimental study was also carried out for measuring the acceleration of vibration response due to the numerical dynamic inertia force. The results showed that the dynamic inertia force acting on the main bearing is the main cause of the vibration of engine.

The efficiency of aerodynamic force production in Drosophila.

Science.gov (United States)

Lehmann, F O

2001-12-01

Total efficiency of aerodynamic force production in insect flight depends on both the efficiency with which flight muscles turn metabolic energy into muscle mechanical power and the efficiency with which this power is converted into aerodynamic flight force by the flapping wings. Total efficiency has been estimated in tethered flying fruit flies Drosophila by modulating their power expenditures in a virtual reality flight simulator while simultaneously measuring stroke kinematics, locomotor performance and metabolic costs. During flight, muscle efficiency increases with increasing flight force production, whereas aerodynamic efficiency of lift production decreases with increasing forces. As a consequence of these opposite trends, total flight efficiency in Drosophila remains approximately constant within the kinematic working range of the flight motor. Total efficiency is broadly independent of different profile power estimates and typically amounts to 2-3%. The animal achieves maximum total efficiency near hovering flight conditions, when the beating wings produce flight forces that are equal to the body weight of the insect. It remains uncertain whether this small advantage in total efficiency during hovering flight was shaped by evolutionary factors or results from functional constraints on both the production of mechanical power by the indirect flight muscles and the unsteady aerodynamic mechanisms in flapping flight.

Anticipatory synergy adjustments reflect individual performance of feedforward force control.

Science.gov (United States)

Togo, Shunta; Imamizu, Hiroshi

2016-10-06

We grasp and dexterously manipulate an object through multi-digit synergy. In the framework of the uncontrolled manifold (UCM) hypothesis, multi-digit synergy is defined as the coordinated control mechanism of fingers to stabilize variable important for task success, e.g., total force. Previous studies reported anticipatory synergy adjustments (ASAs) that correspond to a drop of the synergy index before a quick change of the total force. The present study compared ASA's properties with individual performances of feedforward force control to investigate a relationship of those. Subjects performed a total finger force production task that consisted of a phase in which subjects tracked target line with visual information and a phase in which subjects produced total force pulse without visual information. We quantified their multi-digit synergy through UCM analysis and observed significant ASAs before producing total force pulse. The time of the ASA initiation and the magnitude of the drop of the synergy index were significantly correlated with the error of force pulse, but not with the tracking error. Almost all subjects showed a significant increase of the variance that affected the total force. Our study directly showed that ASA reflects the individual performance of feedforward force control independently of target-tracking performance and suggests that the multi-digit synergy was weakened to adjust the multi-digit movements based on a prediction error so as to reduce the future error. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

DETERMINATION OF FRAME FORCE FOR ELECTRIC LOCOMOTIVE VL80 WHEN MOVING IN THE CURVED TRACK SECTIONS

Directory of Open Access Journals (Sweden)

A. Y. Kuzyshyn

2017-06-01

Full Text Available Purpose. When locomotives move in curved sections of the railway track, horizontal forces arise, which lead to pressing the ridge of the wheel pair to the railway track. The article is aimed to develop a method for determining the frame force acting on the bogie from the side of body of the locomotive section using the current methodology of calculating the lateral force. It is also aimed to determine the basic parameters that influence the value of the frame force. It is necessary to construct the dependencies of the frame force on the travel time of electric locomotive in the corresponding curve changing these parameters. Methodology. As is known, the electric locomotive is a multimass mechanical system. We will assume that this system consists of seven bodies: a body, two frames of carriages and four wheel sets. To determine the lateral force acting on the rail from the wheelset one need to solve differential equations of motion of locomotive bogie in curves of small radius. Using the equations of kinetostatics for wheelset one should come to determining the frame force acting on the car bogie from the side of body of the locomotive section. The nominal geometric and mass parameters of parts and components of electric locomotive are taken in the calculations. The curve radius, the length of transition curve, the length of circular curve, the longitudinal slope of railway track and other parameters are fixed values. Findings. There were obtained calculated values of the frame force of electric locomotive VL80 acting on the bogie from the side of body of the locomotive section. Based on the obtained results there were built the dependencies of frame force on the travel time of electric locomotive on the corresponding curve when changing the speed and corresponding elevation of the outer rail. Originality. On the basis of the existing methodology for calculating the lateral force it was developed the method for determining the frame force acting

75 FR 22569 - Privacy Act of 1974; System of Records

Science.gov (United States)

2010-04-29

... DEPARTMENT OF DEFENSE Department of the Air Force [Docket ID: USAF-2010-0014] Privacy Act of 1974... inventory of record systems subject to the Privacy Act of 1974, (5 U.S.C. 552a), as amended. DATES: This... Internet at http://www.regulations.gov as they are received without change, including any personal...

76 FR 37329 - Privacy Act of 1974; System of Records

Science.gov (United States)

2011-06-27

... DEPARTMENT OF DEFENSE Department of the Air Force [Docket ID: USAF-2011-0018] Privacy Act of 1974... of record systems subject to the Privacy Act of 1974 (5 U.S.C. 552a), as amended. DATES: This... public is to make these submissions available for public viewing on the Internet at http://www...

75 FR 22570 - Privacy Act of 1974; System of Records

Science.gov (United States)

2010-04-29

... DEPARTMENT OF DEFENSE Department of the Air Force [Docket ID: USAF-2010-0012] Privacy Act of 1974... inventory of record systems subject to the Privacy Act of 1974, (5 U.S.C. 552a), as amended. DATES: This... on the Internet at http://www.regulations.gov as they are received without change, including any...

76 FR 1411 - Privacy Act of 1974; System of Records

Science.gov (United States)

2011-01-10

... DEPARTMENT OF DEFENSE Department of the Air Force [Docket ID: USAF-2011-0001] Privacy Act of 1974... of record systems subject to the Privacy Act of 1974, (5 U.S.C. 552a), as amended. DATES: This... the public is to make these submissions available for public viewing on the Internet at http://www...

75 FR 63824 - Privacy Act of 1974; System of Records

Science.gov (United States)

2010-10-18

... DEPARTMENT OF DEFENSE Department of the Air Force [Docket ID: USAF-2010-0026] Privacy Act of 1974... inventory of record systems subject to the Privacy Act of 1974, (5 U.S.C. 552a), as amended. DATES: This... for public viewing on the Internet at http://www.regulations.gov as they are received without change...

Atomic Energy Control Act, c A.19, s.1

International Nuclear Information System (INIS)

1985-01-01

The Revised Statutes of Canada 1985 entered into force on 12 December 1988, revoking the previous Atomic Energy Control Act and replacing it with a new version. The new Act (Chapter A-16 of the Revised Statutes) updates the previous text and makes some linguistic corrections. The Atomic Energy Control Act establishes the Atomic Energy Control Board and sets out its duties and powers which include, in particular, the making of regulations for developing, controlling and licensing the production, application and use of atomic energy [fr

Note: A rigid piezo motor with large output force and an effective method to reduce sliding friction force

Energy Technology Data Exchange (ETDEWEB)

Guo, Ying; Lu, Qingyou, E-mail: qxl@ustc.edu.cn [High Magnetic Field Laboratory, Chinese Academy of Sciences and University of Science and Technology of China, Hefei, Anhui 230026 (China); Hefei National Laboratory for Physical Sciences at Microscale, University of Science and Technology of China, Hefei, Anhui 230026 (China); Hou, Yubin [High Magnetic Field Laboratory, Chinese Academy of Sciences and University of Science and Technology of China, Hefei, Anhui 230026 (China)

2014-05-15

We present a completely practical TunaDrive piezo motor. It consists of a central piezo stack sandwiched by two arm piezo stacks and two leg piezo stacks, respectively, which is then sandwiched and spring-clamped by a pair of parallel polished sapphire rods. It works by alternatively fast expanding and contracting the arm/leg stacks while slowly expanding/contracting the central stack simultaneously. The key point is that sufficiently fast expanding and contracting a limb stack can make its two sliding friction forces well cancel, resulting in the total sliding friction force is <10% of the total static friction force, which can help increase output force greatly. The piezo motor's high compactness, precision, and output force make it perfect in building a high-quality harsh-condition (vibration resistant) atomic resolution scanning probe microscope.

Note: A rigid piezo motor with large output force and an effective method to reduce sliding friction force

International Nuclear Information System (INIS)

Guo, Ying; Lu, Qingyou; Hou, Yubin

2014-01-01

We present a completely practical TunaDrive piezo motor. It consists of a central piezo stack sandwiched by two arm piezo stacks and two leg piezo stacks, respectively, which is then sandwiched and spring-clamped by a pair of parallel polished sapphire rods. It works by alternatively fast expanding and contracting the arm/leg stacks while slowly expanding/contracting the central stack simultaneously. The key point is that sufficiently fast expanding and contracting a limb stack can make its two sliding friction forces well cancel, resulting in the total sliding friction force is <10% of the total static friction force, which can help increase output force greatly. The piezo motor's high compactness, precision, and output force make it perfect in building a high-quality harsh-condition (vibration resistant) atomic resolution scanning probe microscope

Calculating Free Energies Using Average Force

Science.gov (United States)

Darve, Eric; Pohorille, Andrew; DeVincenzi, Donald L. (Technical Monitor)

2001-01-01

A new, general formula that connects the derivatives of the free energy along the selected, generalized coordinates of the system with the instantaneous force acting on these coordinates is derived. The instantaneous force is defined as the force acting on the coordinate of interest so that when it is subtracted from the equations of motion the acceleration along this coordinate is zero. The formula applies to simulations in which the selected coordinates are either unconstrained or constrained to fixed values. It is shown that in the latter case the formula reduces to the expression previously derived by den Otter and Briels. If simulations are carried out without constraining the coordinates of interest, the formula leads to a new method for calculating the free energy changes along these coordinates. This method is tested in two examples - rotation around the C-C bond of 1,2-dichloroethane immersed in water and transfer of fluoromethane across the water-hexane interface. The calculated free energies are compared with those obtained by two commonly used methods. One of them relies on determining the probability density function of finding the system at different values of the selected coordinate and the other requires calculating the average force at discrete locations along this coordinate in a series of constrained simulations. The free energies calculated by these three methods are in excellent agreement. The relative advantages of each method are discussed.

Laser radiation forces in laser-produced plasmas

International Nuclear Information System (INIS)

Stamper, J.A.

1975-01-01

There are two contributions to laser radiation forces acting on the electrons. Transfer of momentum from the fields to the electrons results in a field pressure contribution and occurs whenever there is absorption or reflection. The quiver pressure contribution, associated with electron quiver motion, is due to inhomogeneous fields inducing momentum transfer within the electron system. It is shown that the ponderomotive force with force density, (epsilon-1)/8πdel 2 >, does not include the field contribution and does not lead to a general description of macroscopic processes. A theory is discussed which does give a general macroscopic description (absorption, reflection, refraction, and magnetic field generation) and which reduces to the ponderomotive force for purely sinusoidal fields in a neutral, homogeneous, nonabsorbing plasma

Vertical and lateral forces when a permanent magnet above a superconductor traverses in arbitrary directions

Science.gov (United States)

Yang, Yong

2008-12-01

In an actual levitation system composed of high temperature superconductors (HTSs) and permanent magnets (PMs), the levitating bodies may traverse in arbitrary directions. Many previous researchers assumed that the levitating bodies moved in a vertical direction or a lateral direction in order to simplify the problem. In this paper, the vertical and lateral forces acting on the PM are calculated by the modified frozen-image method when a PM above an HTS traverses in arbitrary directions. In order to study the effects of the movement directions on the vertical and lateral forces, comparisons of the forces that act on a PM traversing in a tilted direction with those that act on a PM traversing in a vertical direction or a lateral direction have been presented.

Vertical and lateral forces when a permanent magnet above a superconductor traverses in arbitrary directions

Energy Technology Data Exchange (ETDEWEB)

Yang Yong [Key Laboratory of Applied Superconductivity, Chinese Academy of Sciences, Beijing 100190 (China); Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China)], E-mail: yy@mail.iee.ac.cn

2008-12-15

In an actual levitation system composed of high temperature superconductors (HTSs) and permanent magnets (PMs), the levitating bodies may traverse in arbitrary directions. Many previous researchers assumed that the levitating bodies moved in a vertical direction or a lateral direction in order to simplify the problem. In this paper, the vertical and lateral forces acting on the PM are calculated by the modified frozen-image method when a PM above an HTS traverses in arbitrary directions. In order to study the effects of the movement directions on the vertical and lateral forces, comparisons of the forces that act on a PM traversing in a tilted direction with those that act on a PM traversing in a vertical direction or a lateral direction have been presented.

Vertical and lateral forces when a permanent magnet above a superconductor traverses in arbitrary directions

International Nuclear Information System (INIS)

Yang Yong

2008-01-01

In an actual levitation system composed of high temperature superconductors (HTSs) and permanent magnets (PMs), the levitating bodies may traverse in arbitrary directions. Many previous researchers assumed that the levitating bodies moved in a vertical direction or a lateral direction in order to simplify the problem. In this paper, the vertical and lateral forces acting on the PM are calculated by the modified frozen-image method when a PM above an HTS traverses in arbitrary directions. In order to study the effects of the movement directions on the vertical and lateral forces, comparisons of the forces that act on a PM traversing in a tilted direction with those that act on a PM traversing in a vertical direction or a lateral direction have been presented.

Optical forces, torques, and force densities calculated at a microscopic level using a self-consistent hydrodynamics method

Science.gov (United States)

Ding, Kun; Chan, C. T.

2018-04-01

The calculation of optical force density distribution inside a material is challenging at the nanoscale, where quantum and nonlocal effects emerge and macroscopic parameters such as permittivity become ill-defined. We demonstrate that the microscopic optical force density of nanoplasmonic systems can be defined and calculated using the microscopic fields generated using a self-consistent hydrodynamics model that includes quantum, nonlocal, and retardation effects. We demonstrate this technique by calculating the microscopic optical force density distributions and the optical binding force induced by external light on nanoplasmonic dimers. This approach works even in the limit when the nanoparticles are close enough to each other so that electron tunneling occurs, a regime in which classical electromagnetic approach fails completely. We discover that an uneven distribution of optical force density can lead to a light-induced spinning torque acting on individual particles. The hydrodynamics method offers us an accurate and efficient approach to study optomechanical behavior for plasmonic systems at the nanoscale.

The Rights Granted to Trade Unions Under the Companies Act 71 of ...

African Journals Online (AJOL)

With the entering into force of the Companies Act 71 of 2008 in 2011 a number of rights were granted to trade unions by the act. The Companies Act 71 of 2008 not only grants rights to registered trade unions, as is the case in labour law, but in some cases it grants rights to trade unions representing employees at the ...

The Role of the Right Hemisphere in Speech Act Comprehension

Science.gov (United States)

Holtgraves, Thomas

2012-01-01

In this research the role of the RH in the comprehension of speech acts (or illocutionary force) was examined. Two split-screen experiments were conducted in which participants made lexical decisions for lateralized targets after reading a brief conversation remark. On one-half of the trials the target word named the speech act performed with the…

Experimental study on inter-particle acoustic forces.

Science.gov (United States)

Garcia-Sabaté, Anna; Castro, Angélica; Hoyos, Mauricio; González-Cinca, Ricard

2014-03-01

A method for the experimental measurement of inter-particle forces (secondary Bjerknes force) generated by the action of an acoustic field in a resonator micro-channel is presented. The acoustic radiation force created by an ultrasonic standing wave moves suspended particles towards the pressure nodes and the acoustic pressure induces particle volume oscillations. Once particles are in the levitation plane, transverse and secondary Bjerknes forces become important. Experiments were carried out in a resonator filled with a suspension composed of water and latex particles of different size (5-15 μm) at different concentrations. Ultrasound was generated by means of a 2.5 MHz nominal frequency transducer. For the first time the acoustic force generated by oscillating particles acting on other particles has been measured, and the critical interaction distance in various cases has been determined. Inter-particle forces on the order of 10(-14) N have been measured by using this method.

Comparison of frictional forces on graphene and graphite

International Nuclear Information System (INIS)

Lee, Hyunsoo; Lee, Naesung; Seo, Yongho; Eom, Jonghwa; Lee, SangWook

2009-01-01

We report on the frictional force between an SiN tip and graphene/graphite surfaces using lateral force microscopy. The cantilever we have used was made of an SiN membrane and has a low stiffness of 0.006 N m -1 . We prepared graphene flakes on a Si wafer covered with silicon oxides. The frictional force on graphene was smaller than that on the Si oxide and larger than that on graphite (multilayer of graphene). Force spectroscopy was also employed to study the van der Waals force between the graphene and the tip. Judging that the van der Waals force was also in graphite-graphene-silicon oxide order, the friction is suspected to be related to the van der Waals interactions. As the normal force acting on the surface was much weaker than the attractive force, such as the van der Waals force, the friction was independent of the normal force strength. The velocity dependency of the friction showed a logarithmic behavior which was attributed to the thermally activated stick-slip effect.

Two 'hot buttons' in gas contracting: security performance and force majeure

International Nuclear Information System (INIS)

Park, J.J.

1996-01-01

Two important developments in gas contracting issues are the 'force majeure' provisions and security for performance clauses. 'Force majeure' was defined as any acts of God or any acts of omission by a transporter of gas, which is excused by any event not within the control of the party claiming suspension. 'Force majeure' provisions need to be specifically negotiated in every case. These issues often arise in gas contracting situations, but the nature of Canada's non-litigious oil and gas industry is such that we have had little or no Canadian case law to assist in interpreting what these clauses mean. The 'force majeure' clause is basically meant to protect the parties from events outside normal business risk. The security of performance issue arises when the obligation of a supplier of gas to perform, and the obligation of a buyer of gas to pay, is unsecured, as would be the case for example, if one of the parties becomes bankrupt

Longitudinal forces acting at side-to-end and end-to-side anastomoses when a knitted polyester arterial prosthesis is implanted in the dog.

Science.gov (United States)

Dadgar, L; Downs, A R; Deng, X; Marois, Y; King, M W; Martin, L; Guidoin, R

1995-01-01

In a previous study, which investigated the tensions at the proximal and distal end-to-end anastomoses of a vascular prosthesis, no significant differences were found in the longitudinal forces between the two anastomotic sites after different periods of implantation. The present follow-up study was devised to study the longitudinal forces at a proximal side-to-end and a distal end-to-side anastomosis using a warp knitted polyester prosthesis implanted as a canine thorocoabdominal bypass. The external surface of the prosthesis contained a specially printed "tension indicator" design, which enabled changes in length to be assessed photographically at the two anastomoses at the time of implantation and at sacrifice. The longitudinal force at each site was then calculated using a relationship obtained experimentally between the total longitudinal force and the changes in length of the virgin graft in vitro. The in vitro measurements on the prosthesis were performed using a computer-controlled laser calibration system. Although the results showed a tendency toward a gradual loss in longitudinal force at both anastomoses over 7 months in situ, statistical analysis showed no significant difference in the longitudinal force at the two anastomotic sites after any period of implantation. Histopathological and textile analysis also showed that the characteristics of the prostheses were similar at both anastomotic sites. This does not mean, however, that the intramural stress concentrations experienced by the two sites were the same. While comparing the level of the longitudinal forces measured in this study with those observed in the previous thoracic aorta study using end-to-end anastomoses, no significant differences were observed due to the different types of anastomoses. It would appear that the longitudinal force is not one of the main etiological factors that cause the formation and localization of anastomotic failure.

76 FR 15334 - Aquatic Nuisance Species Task Force Meeting

Science.gov (United States)

2011-03-21

... Task Force Web site at: http://anstaskforce.gov/meetings.php . FOR FURTHER INFORMATION CONTACT: Susan...: http://anstaskforce.gov/meetings.php . Dated: March 14, 2011. Jeffrey Underwood, Acting Assistant...

Community rejection following sexual assault as ‘forced migration’

OpenAIRE

AJ Morgen

2013-01-01

When women are banished from their communities following sexual assault, this rejection should be considered an act of forced migration by the administrators of truth commission reparations programmes.

Evaluation of a Surrogate Contact Model in Force-Dependent Kinematic Simulations of Total Knee Replacement

NARCIS (Netherlands)

Marra, M.A.; Andersen, M.S.; Damsgaard, M.; Koopman, B.; Janssen, D.W.; Verdonschot, N.J.

2017-01-01

Knowing the forces in the human body is of great clinical interest and musculoskeletal (MS) models are the most commonly used tool to estimate them in vivo. Unfortunately, the process of computing muscle, joint contact, and ligament forces simultaneously is computationally highly demanding. The goal

Evaluation of a surrogate contact model in force-dependent kinematic simulations of total knee replacement

NARCIS (Netherlands)

Marra, Marco Antonio; Andersen, Michael S.; Damsgaard, Michael; Koopman, Bart F.J.M.; Janssen, Dennis; Verdonschot, Nico

2017-01-01

Knowing the forces in the human body is of great clinical interest and musculoskeletal (MS) models are the most commonly used tool to estimate them in vivo. Unfortunately, the process of computing muscle, joint contact, and ligament forces simultaneously is computationally highly demanding. The goal

14 CFR 151.51 - Performance of construction work: Sponsor force account.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Performance of construction work: Sponsor... Development Projects § 151.51 Performance of construction work: Sponsor force account. (a) Before undertaking any force account construction work, the sponsor (or any public agency acting as agent for the sponsor...

Nuclear Liability Act. RS, c.29 (1st supp.), s.1

International Nuclear Information System (INIS)

1985-01-01

The Revised Statutes of Canada 1985 which entered into force on 12 December 1988 revoked the Nuclear Liability Act of 1970, replacing it with a new version. The new Act (Chapter N-28 of the Revised Statutes) updates the previous text and makes some linguistic corrections. The principles of the Act of 1970 remain unchanged, namely absolute liability of the nuclear operator, such liability being limited in amount and in time [fr

The Electromotive Force in Different Reference Frames

Science.gov (United States)

Adler, Charles L.

2018-05-01

The electromotive force (EMF) is the work per unit charge around a wire loop caused by a time-varying magnetic flux threading the loop. It is due to a force moving the charges around the loop. This is true whether the change in flux is due to the wire loop being stationary and the field changing in time, or the loop moving through a spatially varying field. In the first case, we say that the time-varying magnetic field induces an electric field that provides the force; in the second, we say that the force is due to the magnetic field acting on the charges in the moving loop. The theory of relativity states that both viewpoints must be equivalent, but it is sometimes difficult to harmonize them.

32 CFR 806b.30 - Evaluating information systems for Privacy Act compliance.

Science.gov (United States)

2010-07-01

... privacy issues are unchanged. (d) The depth and content of the Privacy Impact Assessment should be... 32 National Defense 6 2010-07-01 2010-07-01 false Evaluating information systems for Privacy Act... FORCE ADMINISTRATION PRIVACY ACT PROGRAM Privacy Impact Assessments § 806b.30 Evaluating information...

Federal Act of 29 April 1964 on Liability for Nuclear Damage (Atomic Liability Act)

International Nuclear Information System (INIS)

Under this Act, the operator of a nuclear installation is liable for any nuclear incident occurring in such installation or which is caused by nuclear substances in his charge. If an incident is caused by a radioisotope, the person in possession of the radioisotope at the time of the incident is liable therefore. When an incident occurs during transport of nuclear substances, the carrier is liable in three cases only: when such substances are neither despatched to nor originating from installations on Austrian territory; when they are despatched without the written consent of the Austrian operator who is to receive them; and when they are not destined for a nuclear installation. Other provisions of the Act fix liability ceilings, a basis for apportionment of compensation when several victims are involved and the amount of security for coverage of the operators liability. The Act came into force on 1 September 1964. (NEA) [fr

Nuclear Liability Act as amended (No 484/72)

International Nuclear Information System (INIS)

1972-01-01

This Act which entered into force on 16th June 1972 adopted the essential principles laid down in the Paris Convention. These include in particular absolute liability of the operator, its limitation in amount and in time. (NEA) [fr

Weight, the Normal Force and Newton's Third Law: Dislodging a Deeply Embedded Misconception

Science.gov (United States)

Low, David; Wilson, Kate

2017-01-01

On entry to university, high-achieving physics students from all across Australia struggle to identify Newton's third law force pairs. In particular, less than one in ten can correctly identify the Newton's third law reaction pair to the weight of (gravitational force acting on) an object. Most students incorrectly identify the normal force on the…

Force Relations and Dynamics of Cutting Knife in a Vertical Disc Mobile Wood Chipper

Directory of Open Access Journals (Sweden)

Segun R. BELLO

2011-06-01

Full Text Available The force relations and dynamics of cutting knife in a vertical disc wood chipper were investigated. The tool geometry determined include: rake angle (20 deg C; Shear angle, (fi= 52.15 deg C; the mean frictional angle, (t = 5.71 deg C. The analysis and comparison of the cutting forces has shown that the chips separated from the wood are being formed by off cutting, since normal applied force N is compressive in nature, the magnitude of the forces used by the knife on the wood is expected to increase as the cutting edge of the knife goes deeper into the wood until the value of the resisting force acting against the cut wood Ff is reached and exceeded. The evaluated forces acting on the knife and the chip are: F = 3.63Nmm^-1; N = 34.7 Nmm^-1; Fs= 27.45Nmm^-1; Fn =31.92 Nmm^-1; Ft = -8.46Nmm^-1; Fc = 33.85Nmm^-1. The resultant force acting on the tool face, Pr = 34.89Nmm^-1. The specific cutting pressure, Pc and cutting force needed to cut the timber, Fc, are 1.79 × 10^6 N/m2 and 644.84N respectively. The energy consumed in removing a unit volume of material is 69.96kJ/mm^-3 and the maximum power developed in cutting the chip is 3591.77W (4.82hp. The chipper efficiency (86.6% was evaluated by the highest percentage of accepted chip sizes.

Longitudinal Lorentz force on a subwavelength-diameter optical fiber

International Nuclear Information System (INIS)

Yu Huakang; Fang Wei; Gu Fuxing; Yang Zongyin; Tong Limin; Qiu Min

2011-01-01

We analyze the longitudinal Lorentz forces that a propagating continuous-wave light exerts on a subwavelength-diameter optical fiber. Our theoretical results show that, during the propagating process, the guided light exerts no net time-averaged force on the fiber. Via numerical simulation, we find a significant overall pull force of 0.4 pN/mW acting on a 450-nm-diam fiber tip at a wavelength of 980 nm due to the scattering of the end face and a calculated force distribution reveals the feature of a near-field accumulation. Our results may be helpful to the configuration of optomechanical components or devices based on these fibers.

Against acts of nuclear terrorism; Gegen nuklearterroristische Handlungen

Energy Technology Data Exchange (ETDEWEB)

Heller, W.

2007-12-15

The Act on the International Convention of the United Nations of April 13, 2005 on Combating Acts of Nuclear Terrorism was promulgated in the German Federal Gazette and entered into force one day later. The Convention expresses the deep concern about the worldwide escalation of all kinds and manifestations of acts of terrorism. What was true in April 2005 (the year the UN convention was adopted) is even more true today. At the same time, however, the Convention recognizes the right of all nations to develop and use nuclear power for peaceful purposes, acknowledging their justified interest in the possible benefits of the peaceful uses of nuclear power. As the Convention was signed in German still during the term of office of the Red-Green government, this passage is a remarkable acceptance of the realities of the world and past peaceful uses of nuclear power in Germany. Whether or not the convention will become an effective instrument to be used against acts of nuclear terrorism and threats depends on its entering into force after deposition of 22 ratification documents, and on as many states as possible acceding to it. Irrespective of these aspects, action in the spirit of the Convention should be taken now, criminal law should be adapted, and international cooperation should be improved and strengthened. (orig.)

Climate forcings and climate sensitivities diagnosed from atmospheric global circulation models

Energy Technology Data Exchange (ETDEWEB)

Anderson, Bruce T. [Boston University, Department of Geography and Environment, Boston, MA (United States); Knight, Jeff R.; Ringer, Mark A. [Met Office Hadley Centre, Exeter (United Kingdom); Deser, Clara; Phillips, Adam S. [National Center for Atmospheric Research, Boulder, CO (United States); Yoon, Jin-Ho [University of Maryland, Cooperative Institute for Climate and Satellites, Earth System Science Interdisciplinary Center, College Park, MD (United States); Cherchi, Annalisa [Centro Euro-Mediterraneo per i Cambiamenti Climatici, and Istituto Nazionale di Geofisica e Vulcanologia, Bologna (Italy)

2010-12-15

Understanding the historical and future response of the global climate system to anthropogenic emissions of radiatively active atmospheric constituents has become a timely and compelling concern. At present, however, there are uncertainties in: the total radiative forcing associated with changes in the chemical composition of the atmosphere; the effective forcing applied to the climate system resulting from a (temporary) reduction via ocean-heat uptake; and the strength of the climate feedbacks that subsequently modify this forcing. Here a set of analyses derived from atmospheric general circulation model simulations are used to estimate the effective and total radiative forcing of the observed climate system due to anthropogenic emissions over the last 50 years of the twentieth century. They are also used to estimate the sensitivity of the observed climate system to these emissions, as well as the expected change in global surface temperatures once the climate system returns to radiative equilibrium. Results indicate that estimates of the effective radiative forcing and total radiative forcing associated with historical anthropogenic emissions differ across models. In addition estimates of the historical sensitivity of the climate to these emissions differ across models. However, results suggest that the variations in climate sensitivity and total climate forcing are not independent, and that the two vary inversely with respect to one another. As such, expected equilibrium temperature changes, which are given by the product of the total radiative forcing and the climate sensitivity, are relatively constant between models, particularly in comparison to results in which the total radiative forcing is assumed constant. Implications of these results for projected future climate forcings and subsequent responses are also discussed. (orig.)

Gravity as Quantum Entanglement Force

OpenAIRE

Lee, Jae-Weon; Kim, Hyeong-Chan; Lee, Jungjai

2010-01-01

We conjecture that the total quantum entanglement of matter and vacuum in the universe tends to increase with time, like entropy, and that an effective force is associated with this tendency. We also suggest that gravity and dark energy are types of quantum entanglement forces, similar to Verlinde's entropic force, and give holographic dark energy with an equation of state comparable to current observational data. This connection between quantum entanglement and gravity could give some new in...

Calculation of forces acting on an impurity in a metal subjected to a temperature gradient

International Nuclear Information System (INIS)

Gerl, M.

1966-01-01

In a metal subject to a temperature gradient, an impurity is submitted to both an electrostatic force due to the thermoelectric field and a force due to the scattering of electrons and phonons by this point defect. The scattering of the electrons is treated using a semi-classical approach and a quantum mechanical method. The numerical computation for several impurities in Cu, Ag, and Au requires the knowledge of the resistivity cross-section. and of the thermoelectric power of the impurity in the metal. A tentative estimation of the force due to the phonon-scattering is given for the self-diffusion in Cu. However, the approximations of this calculation do not allow a good comparison with the force due to the electrons. (author) [fr

Reorganised force control in elbow pain patients during isometric wrist extension

DEFF Research Database (Denmark)

Mista, Christian Ariel; Monterde, Sonia; Inglés, Montserrat

2018-01-01

INTRODUCTION: Reorganised force control may be an important adaptation following painful traumas. In this study, force control adaptations were assessed in elbow pain patients. Increasing the contraction demand may overcome pain interference on the motor control and as such act as an internal...... voluntary contraction. Pressure pain thresholds were recorded at the lateral epicondyle and tibialis anterior muscle. Contraction force was recorded using a three-directional force transducer. Participants performed contractions according with visual feedback of the task-related force intensity (main...... direction of wrist extension) and another set of contractions with feedback of the three force directions. Going from the simple to the detailed force feedback will increase the demand of the motor task. Force steadiness in all 3 dimensions and force direction was extracted. RESULTS: Compared with controls...

Rebalancing the Air Force: A Comprehensive Solution

Science.gov (United States)

2011-02-16

the consequences can be significant. High Tempo (Figure 4) Lt Gen Charles E. Stenner , Jr., Chief of the Air Force Reserve, stated while...29 January 2010. 14 Lt Gen Charles E. Stenner Jr., Chief of the Air Force Reserve, ―Total Force Policy 21: A 21 st Century Framework for...Military Force Mix Decisions,‖ White Paper, 15 July 2010. 15 Lt Gen Charles E. Stenner Jr., Chief of the Air Force Reserve, ―Testimony Before the House

Air traffic security act unconstitutional

International Nuclear Information System (INIS)

Heller, W.

2006-01-01

In the interest of more effective protective measures against terrorist attacks, the German federal parliament inter alia added a clause to the Air Traffic Security Act (Sec. 14, Para. 3, Air Traffic Security Act) empowering the armed forces to shoot down aircraft to be used as a weapon against human lives. In Germany, this defense possibility has been discussed also in connection with deliberate crashes of hijacked aircraft on nuclear power plants. The 1 st Division of the German Federal Constitutional Court, in its decision of February 15, 2006, ruled that Sec. 14, Para. 3, Air Traffic Security Act was incompatible with the Basic Law and thus was null and void (file No. 1 BvR 357/05) for two reasons: - There was no legislative authority on the part of the federal government. - The provision was incompatible with the basic right of life and the guarantee of human dignity as enshrined in the Basic Law. (orig.)

76 FR 32224 - Migratory Birds; Take of Migratory Birds by the Armed Forces

Science.gov (United States)

2011-06-03

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service Migratory Birds; Take of Migratory Birds by... Forces to incidentally take migratory birds during approved military readiness activities without violating the Migratory Bird Treaty Act (MBTA). The Authorization Act provided this interim authority to...

Origins of hydrodynamic forces on centrifugal pump impellers

Science.gov (United States)

Adkins, Douglas R.; Brennen, Christopher E.

1987-01-01

Hydrodynamic interactions that occur between a centrifugal pump impeller and volute are experimentally and theoretically investigated. The theoretical analysis considers the inability of the blades to perfectly guide the flow through the impeller, and also includes a quasi-one dimensional treatment of the flow in the volute. The disturbance at the impeller discharge and the resulting forces are determined by the theoretical model. The model is then extended to obtain the hydrodynamic force perturbations that are caused by the impeller whirling eccentrically in the volute. Under many operating conditions, these force perturbations were found to be destablizing. Comparisons are made between the theoretical model and the experimental measurements of pressure distributions and radial forces on the impeller. The theoretical model yields fairly accurate predictions of the radial forces caused by the flow through the impeller. However, it was found that the pressure acting on the front shroud of the impeller has a substantial effect on the destablizing hydrodynamic forces.

Microtubules as mechanical force sensors.

Science.gov (United States)

Karafyllidis, Ioannis G; Lagoudas, Dimitris C

2007-03-01

Microtubules are polymers of tubulin subunits (dimers) arranged on a hexagonal lattice. Each tubulin dimer comprises two monomers, the alpha-tubulin and beta-tubulin, and can be found in two states. In the first state a mobile negative charge is located into the alpha-tubulin monomer and in the second into the beta-tubulin monomer. Each tubulin dimer is modeled as an electrical dipole coupled to its neighbors by electrostatic forces. The location of the mobile charge in each dimer depends on the location of the charges in the dimer's neighborhood. Mechanical forces that act on the microtubule affect the distances between the dimers and alter the electrostatic potential. Changes in this potential affect the mobile negative charge location in each dimer and the charge distribution in the microtubule. The net effect is that mechanical forces affect the charge distribution in microtubules. We propose to exploit this effect and use microtubules as mechanical force sensors. We model each dimer as a two-state quantum system and, following the quantum computation paradigm, we use discrete quantum random walk on the hexagonal microtubule lattice to determine the charge distribution. Different forces applied on the microtubule are modeled as different coin biases leading to different probability distributions of the quantum walker location, which are directly connected to different charge distributions. Simulation results show that there is a strong indication that microtubules can be used as mechanical force sensors and that they can also detect the force directions and magnitudes.

Forces acting on a small particle in an acoustical field in a thermoviscous fluid.

Science.gov (United States)

Karlsen, Jonas T; Bruus, Henrik

2015-10-01

We present a theoretical analysis of the acoustic radiation force on a single small spherical particle, either a thermoviscous fluid droplet or a thermoelastic solid particle, suspended in a viscous and heat-conducting fluid medium. Within the perturbation assumptions, our analysis places no restrictions on the length scales of the viscous and thermal boundary-layer thicknesses δ(s) and δ(t) relative to the particle radius a, but it assumes the particle to be small in comparison to the acoustic wavelength λ. This is the limit relevant to scattering of ultrasound waves from nanometer- and micrometer-sized particles. For particles of size comparable to or smaller than the boundary layers, the thermoviscous theory leads to profound consequences for the acoustic radiation force. Not only do we predict forces orders of magnitude larger than expected from ideal-fluid theory, but for certain relevant choices of materials, we also find a sign change in the acoustic radiation force on different-sized but otherwise identical particles. These findings lead to the concept of a particle-size-dependent acoustophoretic contrast factor, highly relevant to acoustic separation of microparticles in gases, as well as to handling of nanoparticles in lab-on-a-chip systems.

Friction Force: From Mechanics to Thermodynamics

Science.gov (United States)

Ferrari, Christian; Gruber, Christian

2010-01-01

We study some mechanical problems in which a friction force is acting on a system. Using the fundamental concepts of state, time evolution and energy conservation, we explain how to extend Newtonian mechanics to thermodynamics. We arrive at the two laws of thermodynamics and then apply them to investigate the time evolution and heat transfer of…

Are skeletal muscles independent actuators? Force transmission from soleus muscle in the cat

NARCIS (Netherlands)

Maas, H.; Sandercock, T.G.

2008-01-01

It is unclear if skeletal muscles act mechanically as independent actuators. The purpose of the present study was to investigate force transmission from soleus (SO) muscle for physiological lengths as well as relative positions in the intact cat hindlimb. We hypothesized that force transmission from

Change Forces: Implementing Change in a Secondary School for the Common Good

Science.gov (United States)

Melville, Wayne; Bartley, Anthony; Weinburgh, Molly

2012-01-01

In this article, we investigate the change forces that act on administrators, subject department chairpersons and teachers as they seek to implement a change in a Canadian secondary school. Using a case study methodology, our analysis of the data uses Sergiovanni's (1998) six change forces: bureaucratic, personal, market, professional, cultural,…

The Air Force’s Individual Mobilization Augmentee Program: Is the Current Organizational Structure Viable?

Science.gov (United States)

2012-10-01

support ongoing efforts by Lt Gen Charles Stenner to transform the Reserve into the operational, cost-effective, enhanced force that he envisions.35...Charles E. Stenner , Total Force Policy 21: A 21st Century Framework for Military Force Mix Decisions, Air Force Reserve White Paper (Washington, DC...20. Stenner , Total Force Policy 21, 3–5. 21. Readiness Management Group, RMG Individual Reserve Guide, 8–9. 22. Ibid.; and Stenner , Total Force

Forced underwater laminar flows with active magnetohydrodynamic metamaterials

Science.gov (United States)

Culver, Dean; Urzhumov, Yaroslav

2017-12-01

Theory and practical implementations for wake-free propulsion systems are proposed and proven with computational fluid dynamic modeling. Introduced earlier, the concept of active hydrodynamic metamaterials is advanced by introducing magnetohydrodynamic metamaterials, structures with custom-designed volumetric distribution of Lorentz forces acting on a conducting fluid. Distributions of volume forces leading to wake-free, laminar flows are designed using multivariate optimization. Theoretical indications are presented that such flows can be sustained at arbitrarily high Reynolds numbers. Moreover, it is shown that in the limit Re ≫102 , a fixed volume force distribution may lead to a forced laminar flow across a wide range of Re numbers, without the need to reconfigure the force-generating metamaterial. Power requirements for such a device are studied as a function of the fluid conductivity. Implications to the design of distributed propulsion systems underwater and in space are discussed.

A standing pressure wave hypothesis of oscillating forces generated during a steam line break

International Nuclear Information System (INIS)

Tinoco, H.

2001-01-01

A rapid glance at the figure depicting the net forces acting on the reactor vessel and internals, as obtained through a CFD simulation of a BWR steam line break, reveals an amazing oscillating regularity of these forces which is in glaring contrast to the chaotic behaviour of the steam pressure field in the steam annulus. Assuming that the decompression process excites and maintains standing pressure waves in the annular cylindrical region constituted by the steam annulus, it is possible to reconstruct the net forces acting on the reactor vessel and internals through the contribution of almost only the first dispersive mode. If a Neumann boundary condition is assumed at the section connecting the steam annulus to the steam dome, the frequency predicted is approximately % 5.9 higher than that of the CFD simulations. However, this connecting section allows wave transmission, and a more appropriate boundary condition should be one of the Robin type. Therefore, this section is modelled as an absorbing wall, and the corresponding normal impedance is calculated using the CFD simulations. Week non-linear effects can also be observed in the calculated forces through the presence of the first subharmonic. By the methodology described above, an estimate of the forces acting on the reactor vessel and internals of unit 3 of Forsmark Nuclear Power Plant has been obtained. (author)

The Bribery Act 2010: an overview for district nurses.

Science.gov (United States)

Griffith, Richard; Tengnah, Cassam

2012-10-01

The Bribery Act 2010 has been in force for a little over a year and has already served to reinforce the need for NHS organisations to adopt a proactive approach to preventing any suggestion that their staff are accepting inducements, in the form of gifts or hospitality, that could influence their performance. The robust policies on the acceptance of gifts and hospitality demanded by the 2010 Act require district nurses to be very cautious when offered a gift by a patient or commercial organisation. This article considers the implications of the Bribery Act 2010 on district nurse practice and the implications of failing to meet its provisions.

75 FR 19377 - Privacy Act of 1974; Systems of Records

Science.gov (United States)

2010-04-14

.... 552a(r), of the Privacy Act of 1974, as amended, were submitted on March 31, 2010, to the House..., forced password-change protocols or also equipped with ``Smart Card'' technology that requires the...

On the contribution of circumferential resonance modes in acoustic radiation force experienced by cylindrical shells

Science.gov (United States)

Rajabi, Majid; Behzad, Mehdi

2014-10-01

A body insonified by a constant (time-varying) intensity sound field is known to experience a steady (oscillatory) force that is called the steady-state (dynamic) acoustic radiation force. Using the classical resonance scattering theorem (RST) which suggests the scattered field as a superposition of a resonance field and a background (non-resonance) component, we show that the radiation force acting on a cylindrical shell may be synthesized as a composition of three components: background part, resonance part and their interaction. The background component reveals the pure geometrical reflection effects and illustrates a regular behavior with respect to frequency, while the others demonstrate a singular behavior near the resonance frequencies. The results illustrate that the resonance effects associated to partial waves can be isolated by the subtraction of the background component from the total (steady-state or dynamic) radiation force function (i.e., residue component). In the case of steady-state radiation force, the components are exerted on the body as static forces. For the case of oscillatory amplitude excitation, the components are exerted at the modulation frequency with frequency-dependant phase shifts. The results demonstrate the dominant contribution of the non-resonance component of dynamic radiation force at high frequencies with respect to the residue component, which offers the potential application of ultrasound stimulated vibro-acoustic spectroscopy technique in low frequency resonance spectroscopy purposes. Furthermore, the proposed formulation may be useful essentially due to its intrinsic value in physical acoustics. In addition, it may unveil the contribution of resonance modes in the dynamic radiation force experienced by the cylindrical objects and its underlying physics.

Forces acting on a small particle in an acoustical field in a thermoviscous fluid

DEFF Research Database (Denmark)

Karlsen, Jonas Tobias; Bruus, Henrik

2015-01-01

We present a theoretical analysis of the acoustic radiation force on a single small spherical particle, either a thermoviscous fluid droplet or a thermoelastic solid particle, suspended in a viscous and heat-conducting fluid medium. Within the perturbation assumptions, our analysis places no rest...... as to handling of nanoparticles in lab-on-a-chip systems.......We present a theoretical analysis of the acoustic radiation force on a single small spherical particle, either a thermoviscous fluid droplet or a thermoelastic solid particle, suspended in a viscous and heat-conducting fluid medium. Within the perturbation assumptions, our analysis places...... of materials, we also find a sign change in the acoustic radiation force on different-sized but otherwise identical particles. These findings lead to the concept of a particle-size-dependent acoustophoretic contrast factor, highly relevant to acoustic separation of microparticles in gases, as well...

Magnus force on quantum Hall skyrmions and vortices

International Nuclear Information System (INIS)

Dhar, S.; Basu, B.; Bandyopadhyay, P.

2003-01-01

We have discussed here the Magnus force acting on the vortices and skyrmions in the quantum Hall systems. We have found that it is generated by the chirality of the system which is associated with the Berry phase and is same for both the cases

ACTS – SUCCESS STORY

Indian Academy of Sciences (India)

First page Back Continue Last page Overview Graphics. ACTS – SUCCESS STORY. Totally 103 experiments were conducted and the programme succeeded in the areas. Medicine; Education; Defence; Emergency Response; Maritime and Aeronautical Mobile Communications; Science and Astronomy.

Neuronal NOS inhibitor 1-(2-trifluoromethylphenyl)-imidazole augment the effects of antidepressants acting via serotonergic system in the forced swimming test in rats.

Science.gov (United States)

Ulak, Güner; Mutlu, Oguz; Akar, Füruzan Yildiz; Komsuoğlu, F Ipek; Tanyeri, Pelin; Erden, B Faruk

2008-10-01

Treatment-resistant depression has necessitated new therapeutic strategies in augmenting the therapeutic actions of currently existing antidepressant drugs. The aim of this study was to investigate the possibility of synergistic interaction between 1-(2-trifluoromethylphenyl)-imidazole (TRIM), a novel neuronal nitric oxide synthase (nNOS) inhibitor and conventional antidepressants of different classes in the forced swimming test (FST) in rats. TRIM decreased the immobility time at 50 mg/kg doses in the FST in rats. Treatment with a behaviourally subeffective dose of TRIM (20 mg/kg) augmented the behavioural effect of tricyclic antidepressant imipramine, selective serotonin re-uptake inhibitor (SSRI) citalopram and fluoxetine or selective serotonin reuptake enhancer tianeptine but failed to augment the antidepressant effect of reboxetine, a noradrenaline re-uptake inhibitor, in this test. Therefore inhibition of NOS augments the effects of antidepressants acting on serotonergic system in the FST. Neither TRIM (10-50 mg/kg) nor other drug treatments affected the locomotor activity of animals. These findings are in agreement with the view that antidepressant effects or augmentation of these effects in the FST may be explained with inhibition of NOS activity and this may be a new approach in offering greater therapeutic efficacy of antidepressants acting via serotonergic system.

Repulsive Casimir force from fractional Neumann boundary conditions

International Nuclear Information System (INIS)

Lim, S.C.; Teo, L.P.

2009-01-01

This Letter studies the finite temperature Casimir force acting on a rectangular piston associated with a massless fractional Klein-Gordon field at finite temperature. Dirichlet boundary conditions are imposed on the walls of a d-dimensional rectangular cavity, and a fractional Neumann condition is imposed on the piston that moves freely inside the cavity. The fractional Neumann condition gives an interpolation between the Dirichlet and Neumann conditions, where the Casimir force is known to be always attractive and always repulsive respectively. For the fractional Neumann boundary condition, the attractive or repulsive nature of the Casimir force is governed by the fractional order which takes values from zero (Dirichlet) to one (Neumann). When the fractional order is larger than 1/2, the Casimir force is always repulsive. For some fractional orders that are less than but close to 1/2, it is shown that the Casimir force can be either attractive or repulsive depending on the aspect ratio of the cavity and the temperature.

UNDERSTANDING THE “HOUSEHOLDER DEFENCE”: PROPORTIONALITY AND REASONABLENESS IN DEFENSIVE FORCE

OpenAIRE

Dsouza, M.

2016-01-01

IN Collins v Secretary of State [2016] EWHC 33 (Admin), the High Court refused to declare that Criminal Justice and Immigration Act 2008, s. 76(5A) – the so-called “householder's defence” – was incompatible with the right to life enshrined in Article 2 of the ECHR, in that it failed to protect the lives of attackers sufficiently. Section 76(5A) was inserted into the 2008 Act by Crime and Courts Act 2013, s. 43, and came into force in April 2013.

α-Helix Unwinding as Force Buffer in Spectrins.

Science.gov (United States)

Takahashi, Hirohide; Rico, Felix; Chipot, Christophe; Scheuring, Simon

2018-03-27

Spectrins are cytoskeletal proteins located at the inner face of the plasma membrane, making connections between membrane anchors and the actin cortex, and between actin filaments. Spectrins share a common structure forming a bundle of 3 α-helices and play a major role during cell deformation. Here, we used high-speed force spectroscopy and steered molecular dynamics simulations to understand the mechanical stability of spectrin, revealing a molecular force buffering function. We find that spectrin acts as a soft spring at short extensions (70-100 Å). Under continuous external stretching, its α-helices unwind, leading to a viscous mechanical response over larger extensions (100-300 Å), represented by a constant-force plateau in force/extension curves. This viscous force buffering emerges from a quasi-equilibrium competition between disruption and re-formation of α-helical hydrogen bonds. Our results suggest that, in contrast to β-sheet proteins, which unfold in a catastrophic event, α-helical spectrins dominantly unwind, providing a viscous force buffer over extensions about 5 times their folded length.

Quantification of Staphylococcus aureus adhesion forces on various dental restorative materials using atomic force microscopy

Energy Technology Data Exchange (ETDEWEB)

Merghni, Abderrahmen, E-mail: abderrahmen_merghni@yahoo.fr [Laboratoire des Maladies Transmissibles et Substances biologiquement actives (LR99ES27) Faculté de Pharmacie de Monastir, Université de Monastir (Tunisia); Kammoun, Dorra [Laboratoire de Biomatériaux et Biotechnologie, Faculté de Médecine Dentaire, Monastir (Tunisia); Hentati, Hajer [Laboratoire de Recherche en Santé Orale et Réhabilitation Bucco-Faciale (LR12ES11), Faculté de Médecine Dentaire de Monastir, Université de Monastir (Tunisia); Janel, Sébastien [BioImaging Center Lille-FR3642, Lille (France); Popoff, Michka [Cellular Microbiology and Physics of Infection-CNRS UMR8204, INSERM U1019, Institut Pasteur de Lille, Lille University (France); Lafont, Frank [BioImaging Center Lille-FR3642, Lille (France); Cellular Microbiology and Physics of Infection-CNRS UMR8204, INSERM U1019, Institut Pasteur de Lille, Lille University (France); Aouni, Mahjoub [Laboratoire des Maladies Transmissibles et Substances biologiquement actives (LR99ES27) Faculté de Pharmacie de Monastir, Université de Monastir (Tunisia); Mastouri, Maha [Laboratoire des Maladies Transmissibles et Substances biologiquement actives (LR99ES27) Faculté de Pharmacie de Monastir, Université de Monastir (Tunisia); Laboratoire de Microbiologie, CHU Fattouma Bourguiba de Monastir (Tunisia)

2016-08-30

Highlights: • 4 dental restorative materials were characterized for roughness, angle contact water and surface free energy. • AFM adhesion forces of S. aureus to tested materials were achieved in presence and absence of salivary conditioning film. • S. aureus initial adhesion is dependent on the surface free energy and roughness. - Abstract: In the oral cavity dental restorative biomaterials can act as a reservoir for infection with opportunistic Staphylococcus aureus pathogen, which can lead to the occurrence of secondary caries and treatment failures. Our aim was to evaluate the adhesion forces by S. aureus on four dental restorative biomaterials and to correlate this finding to differences in specific surface characteristics. Additionally, the influence of salivary conditioning films in exerted adhesion forces was investigated. The substrate hydrophobicity was measured by goniometer and the surface free energy was calculated using the equilibrium advancing contact angle values of water, formamide, and diiodomethane on the tested surfaces. The surface roughness was determined using atomic force microscope (AFM). Additionally, cell force spectroscopy was achieved to quantify the forces that drive cell-substrate interactions. S. aureus bacterium exerted a considerable adhesion forces on various dental restorative materials, which decreased in the presence of saliva conditioning film. The influence of the surface roughness and free energy in initial adhesion appears to be more important than the effect of hydrophobicity, either in presence or absence of saliva coating. Hence, control of surface properties of dental restorative biomaterials is of crucial importance in preventing the attachment and subsequent the biofilm formation.

Quantification of Staphylococcus aureus adhesion forces on various dental restorative materials using atomic force microscopy

International Nuclear Information System (INIS)

Merghni, Abderrahmen; Kammoun, Dorra; Hentati, Hajer; Janel, Sébastien; Popoff, Michka; Lafont, Frank; Aouni, Mahjoub; Mastouri, Maha

2016-01-01

Highlights: • 4 dental restorative materials were characterized for roughness, angle contact water and surface free energy. • AFM adhesion forces of S. aureus to tested materials were achieved in presence and absence of salivary conditioning film. • S. aureus initial adhesion is dependent on the surface free energy and roughness. - Abstract: In the oral cavity dental restorative biomaterials can act as a reservoir for infection with opportunistic Staphylococcus aureus pathogen, which can lead to the occurrence of secondary caries and treatment failures. Our aim was to evaluate the adhesion forces by S. aureus on four dental restorative biomaterials and to correlate this finding to differences in specific surface characteristics. Additionally, the influence of salivary conditioning films in exerted adhesion forces was investigated. The substrate hydrophobicity was measured by goniometer and the surface free energy was calculated using the equilibrium advancing contact angle values of water, formamide, and diiodomethane on the tested surfaces. The surface roughness was determined using atomic force microscope (AFM). Additionally, cell force spectroscopy was achieved to quantify the forces that drive cell-substrate interactions. S. aureus bacterium exerted a considerable adhesion forces on various dental restorative materials, which decreased in the presence of saliva conditioning film. The influence of the surface roughness and free energy in initial adhesion appears to be more important than the effect of hydrophobicity, either in presence or absence of saliva coating. Hence, control of surface properties of dental restorative biomaterials is of crucial importance in preventing the attachment and subsequent the biofilm formation.

78 FR 29378 - Aquatic Nuisance Species Task Force; Public Teleconference/Webinar

Science.gov (United States)

2013-05-20

... Invasive Species Awareness Week, Michigan and Mississippi ANS Management Plans, and Asian Carp Surveillance....gov . Dated: May 14, 2013. Jeffrey Underwood, Acting Co-Chair, Aquatic Nuisance Species Task Force...

Phase space imaging of a beam of charged particles by frictional forces

International Nuclear Information System (INIS)

Daniel, H.

1977-01-01

In the case of frictional forces, defined by always acting opposite to the particle motion, Liouville's theorem does not apply. The effect of such forces on a beam of charged particles is calculated in closed form. Emphasis is given to the phase space imaging by a moderator. Conditions for an increase in phase space density are discussed. (Auth.)

Reducing forces during drilling brittle hard materials by using ultrasonic and variation of coolant

Science.gov (United States)

Schopf, C.; Rascher, R.

2016-11-01

The process of ultrasonic machining is especially used for brittle hard materials as the additional ultrasonic vibration of the tool at high frequencies and low amplitudes acts like a hammer on the surface. With this technology it is possible to drill holes with lower forces, therefor the machining can be done faster and the worktime is much less than conventionally. A three-axis dynamometer was used to measure the forces, which act between the tool and the sample part. A focus is set on the sharpness of the tool. The results of a test series are based on the Sauer Ultrasonic Grinding Centre. On the same machine it is possible to drill holes in the conventional way. Additional to the ultasonic Input the type an concentration of coolant is important for the Drilling-force. In the test there were three different coolant and three different concentrations tested. The combination of ultrasonic vibration and the right coolant and concentration is the best way to reduce the Forces. Another positive effect is, that lower drilling-forces produce smaller chipping on the edge of the hole. The way to reduce the forces and chipping is the main issue of this paper.

Monolithic Microwave Integrated Circuit (MMIC) Phased Array Demonstrated With ACTS

Science.gov (United States)

1996-01-01

Monolithic Microwave Integrated Circuit (MMIC) arrays developed by the NASA Lewis Research Center and the Air Force Rome Laboratory were demonstrated in aeronautical terminals and in mobile or fixed Earth terminals linked with NASA's Advanced Communications Technology Satellite (ACTS). Four K/Ka-band experimental arrays were demonstrated between May 1994 and May 1995. Each array had GaAs MMIC devices at each radiating element for electronic beam steering and distributed power amplification. The 30-GHz transmit array used in uplinks to ACTS was developed by Lewis and Texas Instruments. The three 20-GHz receive arrays used in downlinks from ACTS were developed in cooperation with the Air Force Rome Laboratory, taking advantage of existing Air Force integrated-circuit, active-phased-array development contracts with the Boeing Company and Lockheed Martin Corporation. Four demonstrations, each related to an application of high interest to both commercial and Department of Defense organizations, were conducted. The location, type of link, and the data rate achieved for each of the applications is shown. In one demonstration-- an aeronautical terminal experiment called AERO-X--a duplex voice link between an aeronautical terminal on the Lewis Learjet and ACTS was achieved. Two others demonstrated duplex voice links (and in one case, interactive video links as well) between ACTS and an Army high-mobility, multipurpose wheeled vehicle (HMMWV, or "humvee"). In the fourth demonstration, the array was on a fixed mount and was electronically steered toward ACTS. Lewis served as project manager for all demonstrations and as overall system integrator. Lewis engineers developed the array system including a controller for open-loop tracking of ACTS during flight and HMMWV motion, as well as a laptop data display and recording system used in all demonstrations. The Jet Propulsion Laboratory supported the AERO-X program, providing elements of the ACTS Mobile Terminal. The successful

The Relation Between Market Forces and Employee Motivation : Consequences of the Introduction of Market Forces in the Dutch Childcare Sector

NARCIS (Netherlands)

Plantinga, Mirjam; Plantenga, Janneke; Siegers, Jacques

The Dutch childcare sector has undergone a transition from a welfare sector into a market sector. The final step in this transition process was taken with the introduction of a new Dutch Childcare Act on 1 January 2005. In discussions about the introduction of market forces, the possible effects on

1990 No. 1918. The Nuclear Installations Act 1965 (Repeal and Modifications) Regulations 1990

International Nuclear Information System (INIS)

1990-01-01

These Regulations entered into force on 31 October 1990. They repeal part of Section (1) of the Nuclear Installations Act 1965 to remove the exemption of the United Kingdom Atomic Energy Authority (UKAEA) from licensing under the Act. The Regulations also amend the 1965 Act to ensure that the UKAEA's duties in respect of the safety of premises it occupies will continue to apply whether or not a nuclear site licence has been granted. (NEA) [fr

The Use of Force Notation to Detect Students' Misconceptions: Mutual Interactions Case

Science.gov (United States)

Serhane, Ahcene; Zeghdaoui, Abdelhamid; Debiache, Mehdi

2017-01-01

Using a conventional notation for representing forces on diagrams, students were presented with questions on the interaction between two objects. The results show that complete understanding of Newton's Third Law of Motion is quite rare, and that some problems relate to misunderstanding which force acts on each body. The use of the terms…

Pre-Acting Control for Shock and Impact Isolation Systems

Directory of Open Access Journals (Sweden)

D.V. Balandin

2005-01-01

Full Text Available Pre-acting control in shock/impact isolation systems is studied. With pre-acting control, the isolation system begins to respond to an impact before this impact has been applied to the base. The limiting performance of the isolator with pre-acting control is investigated for a single-degree-of-freedom system subject to an instantaneous impact. The isolation performance index is defined as the maximum of the absolute value of the displacement of the object to be isolated relative to the base, provided that the magnitude of the control force transmitted to the object does not exceed a prescribed value. It is shown that there is a substantial advantage in the use of pre-acting isolators over isolators without pre-action. Particular attention is given to a pre-acting isolator based on a passive elastic element (a spring separating the object to be protected from the base. An example illustrates the calculation of the design parameters of such an isolator.

RPTP-alpha acts as a transducer of mechanical force on alphav/beta3-integrin-cytoskeleton linkages

DEFF Research Database (Denmark)

von Wichert, Gotz; Jiang, Guoying; Kostic, Ana

2003-01-01

Cell motility on ECM critically depends on the cellular response to force from the matrix. We find that force-dependent reinforcement of alphav/beta3-integrin-mediated cell-matrix connections requires the receptor-like tyrosine phosphatase alpha (RPTPalpha). RPTPalpha colocalizes with alphav...... of alphav/beta3-integrin-cytoskeleton connections during the initial phase of ECM contact. These observations indicate that Src family kinases have distinct functions during adhesion site assembly, and that RPTPalpha is an early component in force-dependent signal transduction pathways leading...

Experimental study on the control interaction force coefficient; Soju ryutairyoku kansho keisu ni kansuru jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakatake, K; Oda, K; Yoshitake, A; Fujita, K; Nakajima, A [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1996-04-10

The interaction force induced to hull by steering is important for prediction of control performance of ships. The control interaction force coefficient dependent on the steering has been investigated through the rudder angle tests using three small model ships with a length of 2.5 m, i.e., mathematical type of ship, cargo type of ship, and tanker type of ship. The interaction forces acting on the hull, propeller, and rudder were determined by measuring the lateral force as well as the forward force of the hydrodynamic forces acting on the rudder. These forces were compared with the theoretically calculated values. Prior to the rudder angle tests, the self propulsion factor and the number of revolution of propeller were determined from the results of the open water tests, resistance tests, and self propulsion tests by the changing load method. The rudder angle tests were conducted under this number of revolution of propeller as a standard condition, and under those increasing and decreasing by 15%. Consequently, the interaction forces determined from the rudder angle tests agreed well with those determined from the other tests. When comparing the control hydrodynamic forces determined from the tests with those theoretically calculated, a similar trend was observed. Effectiveness of the theoretical model was confirmed. 4 refs., 14 figs., 3 tabs.

Act of 19 June 1974 on Compensation for Nuclear Damage

International Nuclear Information System (INIS)

1974-01-01

This Act which came into force on 18 September 1974 replaces the nuclear third party liability provisions of the 1962 Act on nuclear installations. Its adoption enabled the Danish Government to ratify the 1960 Paris Convention and the 1963 Brussels Supplementary Convention. In accordance with the principles prescribed by these Conventions, the Act establishes an absolute and limited third party liability system (75 million Danish Krone) and compulsory insurance for the operator of a nuclear installation situated in Denmark. In certain conditions, the State may have to intervene to ensure compensation of nuclear damage exceeding the financial security provided by the operator liable. (NEA) [fr

On the axioms of the forces in the mechanics of rigid bodies

Directory of Open Access Journals (Sweden)

Lámer Géza

2017-01-01

Full Text Available Newton summarised knowledge related to forces in three axioms. The first and second ones define the mechanical state and motion of the examined body when there is no force or when force is exerted on the body. The third defines the law of action and reaction. Newton did not define it as separate axiom but assumed that forces are completely independent from each other. The statics applies four axioms. The first applies to the balance of two forces while the second one applies of three forces. The third axiom defines the relationships inside an equilibrium force system. The fourth one is the axiom of action and reaction. The two axiom systems are independent from each other. Further the independent axioms are applied in case of constraint forces: frictionless reaction force orthogonal on the forced surface, friction force acts in the direction of the motion, the deformation can be elastic, plastic and viscous.

Forces on wheels and fuel consumption in cars

Science.gov (United States)

Güémez, J.; Fiolhais, M.

2013-07-01

Motivated by real classroom discussions, we analyze the forces acting on moving vehicles, specifically friction on their wheels. In typical front-wheel-drive cars when the car accelerates these forces are in the forward direction in the front wheels, but they are in the opposite direction in the rear wheels. The situation may be intriguing for students, but it may also be helpful and stimulating to clarify the role of friction forces on rolling objects. In this paper we also study the thermodynamical aspects of an accelerating car, relating the distance traveled to the amount of fuel consumed. The fuel consumption is explicitly shown to be Galilean invariant and we identify the Gibbs free energy as the relevant quantity that enters into the thermodynamical description of the accelerating car. The more realistic case of the car's motion with the dragging forces taken into account is also discussed.

Forces on wheels and fuel consumption in cars

International Nuclear Information System (INIS)

Güémez, J; Fiolhais, M

2013-01-01

Motivated by real classroom discussions, we analyze the forces acting on moving vehicles, specifically friction on their wheels. In typical front-wheel-drive cars when the car accelerates these forces are in the forward direction in the front wheels, but they are in the opposite direction in the rear wheels. The situation may be intriguing for students, but it may also be helpful and stimulating to clarify the role of friction forces on rolling objects. In this paper we also study the thermodynamical aspects of an accelerating car, relating the distance traveled to the amount of fuel consumed. The fuel consumption is explicitly shown to be Galilean invariant and we identify the Gibbs free energy as the relevant quantity that enters into the thermodynamical description of the accelerating car. The more realistic case of the car's motion with the dragging forces taken into account is also discussed. (paper)

Coriolis force and Sagnac effect

International Nuclear Information System (INIS)

Gogberashvili, Merab

2002-02-01

The optical Sagnac effect is considered, when the fictitious gravitational field simulates the reflections from the mirrors. It is shown that no contradiction exists between the conclusions of the laboratory and rotated observers. Because of the acting of gravity-like Coriolis force the trajectories of co- and anti-rotating photons have different radii in the rotating reference frame, while in the case of the equal radius the effective gravitational potentials for the photons have to be different. (author)

The implications of force reflection for teleoperation in space

International Nuclear Information System (INIS)

Draper, J.V.; Herndon, J.N.; Moore, W.E.

1987-01-01

This paper reviews previous research on teleoperator force feedback and reports results of a testing program which assessed the impact of force reflection on teleoperator task performance. Force reflection is a type of force feedback in which the forces acting on the remote portion of the teleoperator are displayed to the operator by back-driving the master controller. The testing program compared three force reflection levels: 4 to 1 (four units of force on the slave produce one unit of force at the master controller), 1 to 1, and infinity to 1 (no force reflection). Time required to complete tasks, rate of occurrence of errors, the maximum force applied to tasks components, and variability in forces applied to components during completion of representative remote handling tasks were used as dependent variables. Operators exhibited lower error rates, lower peak forces, and more consistent application of forces using force reflection than they did without it. These data support the hypothesis that force reflection provides useful information for teleoperator users. The earlier literature and the results of the experiment are discussed in terms of their implications for space-based teleoperator systems. The discussion describes the impact of force reflection on task completion performance and task strategies, as suggested by the literature. It is important to understand the trade-offs involved in using telerobotic systems with and without force reflection. Force-reflecting systems are typically more expensive (in mass, volume, and price per unit), but they reduce mean time to repair and may be safer to use, compared to systems without force reflection

The study of dynamic force acted on water strider leg departing from water surface

Science.gov (United States)

Sun, Peiyuan; Zhao, Meirong; Jiang, Jile; Zheng, Yelong

2018-01-01

Water-walking insects such as water striders can skate on the water surface easily with the help of the hierarchical structure on legs. Numerous theoretical and experimental studies show that the hierarchical structure would help water strider in quasi-static case such as load-bearing capacity. However, the advantage of the hierarchical structure in the dynamic stage has not been reported yet. In this paper, the function of super hydrophobicity and the hierarchical structure was investigated by measuring the adhesion force of legs departing from the water surface at different lifting speed by a dynamic force sensor. The results show that the adhesion force decreased with the increase of lifting speed from 0.02 m/s to 0.4 m/s, whose mechanic is investigated by Energy analysis. In addition, it can be found that the needle shape setae on water strider leg can help them depart from water surface easily. Thus, it can serve as a starting point to understand how the hierarchical structure on the legs help water-walking insects to jump upward rapidly to avoid preying by other insects.

A new orthodontic force system for moment control utilizing the flexibility of common wires: Evaluation of the effect of contractile force and hook length

Directory of Open Access Journals (Sweden)

Wei-Jen Lai

2018-01-01

Conclusion: The system acted similar to an off-center V-bend and can be applied in clinical practice as an unconventional loop design. We suggest that this force system has the potential for second-order moment control in clinical applications.

Protective force legal issues: the security perspective

International Nuclear Information System (INIS)

Rich, B.L.

1984-01-01

There has been much discussion and some controversy on the legal issues faced by the Department of Energy's (DOE) protective forces in the performance of their security duties. These include the observance of legal proprieties in the arrest of non-violent demonstrators, the use of lethal weapons, and the extent of protective forces' authority to carry weapons and protect DOE's security interests offsite. In brief, the need to protect DOE's security interests may be in nominal conflict with other requirements. When faced with a potential conflict in requirements, we in the DOE security community must place first attention to the security mission -- to deter and prevent hostile acts

A quantum theory of the self-energy of non-relativistic fermions and of the Coulomb-Yukawa force acting between them

International Nuclear Information System (INIS)

Ernst, V.

1978-01-01

The idea of the systematic Weisskopf-Wigner approximation as used sporadically in atomic physics and quantum optics, is extended here to the interaction of a field of non-relativistic fermions with a field of relativistic bosons. It is shown that the usual (non-existing) interaction Hamiltonian of this system can be written as a sum of a countable number of self-adjoint and bounded partial Hamiltonians. The system of these Hamiltonians defines the order hierarchy of the present approximation scheme. To demonstrate its physical utility it is shown that in a certain order it provides satisfactory quantum theory of the 'self-energy' of the fermions under discussion. This is defined as the binding energy of bosons bound to the fermions and building up the latter's 'individual Coulomb or Yukawa fields' in the sense of expectation values of the corresponding field operator. In states of more than one fermion the bound photons act as a mediating agent between the fermions; this mechanism closely resembles the Coulomb or Yukawa 'forces' used in conventional non-relativistic quantum mechanics. (author)

The Soviet Air Force and Strategic Bombing

Science.gov (United States)

1999-04-01

to envision a British Air Force that could be totally divorced from some form of ground support role. Consequently, he saw an air campaign that would...CA: Presidio Press, 1986. Black, Steven K. The Icarus Illusion: Technology, Doctrine and the Soviet Air Force. Monterrey , CA, 1986. Cockburn, Andrew

Experimental Validation of Flow Force Models for Fast Switching Valves

DEFF Research Database (Denmark)

Bender, Niels Christian; Pedersen, Henrik Clemmensen; Nørgård, Christian

2017-01-01

This paper comprises a detailed study of the forces acting on a Fast Switching Valve (FSV) plunger. The objective is to investigate to what extend different models are valid to be used for design purposes. These models depend on the geometry of the moving plunger and the properties of the surroun......This paper comprises a detailed study of the forces acting on a Fast Switching Valve (FSV) plunger. The objective is to investigate to what extend different models are valid to be used for design purposes. These models depend on the geometry of the moving plunger and the properties...... to compare and validate different models, where an effort is directed towards capturing the fluid squeeze effect just before material on material contact. The test data is compared with simulation data relying solely on analytic formulations. The general dynamics of the plunger is validated...

Now Those Who Were Scattered Went about Preaching the Word (Acts 8:4: The Migrant Church and Its Mission According to the Book of Acts

Directory of Open Access Journals (Sweden)

Stenschke, Christoph

2016-03-01

Full Text Available After a brief survey of migration in the Bible, this article examines migration be it voluntary or enforced in the Book of Acts. Acts describes in Stephen's speech in surprising detail experiences of migration in Israel's past and its theological implications. Acts also describes that many early Christian missionaries served in places that were not their places of origin, voluntarily or by force: the disciples ended up in Jerusalem and eventually at the ends of the earth rather than returning to Galilee. Others had come to Jerusalem from elsewhere even before encountering the Gospel and ministered throughout the Eastern Mediterranean world as they became involved in mission. Early Christian mission is closely related to migration and dislocation, voluntary or by force, led by the Spirit and for the sake of the Gospel. Repeatedly other missionaries had to flee in order to avoid persecution. Despite the tragedy and suffering involved, there were also great opportunities which were readily seized: the Gospel moved forward. Much of early Christian mission was accomplished by refugees. A final section reflects on the significance of this portrayal of early Christian mission for the church and its mission in the 21st century.

Functionalization of gold and nanocrystalline diamond atomic force microscope tips for single molecule force spectroscopy

Science.gov (United States)

Drew, Michael E.

The atomic force microscope (AFM) has fueled interest in nanotechnology because of its ability to image surfaces at the nanometer level and act as a molecular force sensor. Functionalization of the surface of an AFM tip surface in a stable, controlled manner expands the capabilities of the AFM and enables additional applications in the fields of single molecule force spectroscopy and nanolithography. Two AFM tip functionalizations are described: the assembly of tripodal molecular tips onto gold AFM tips and the photochemical attachment of terminal alkenes to nanocrystalline diamond (NCD) AFM tips. Two separate tripodal molecules with different linker lengths and a monopodal molecule terminated with biotin were synthesized to attach to a gold AFM tip for single molecule force spectroscopy. The immobilization of these molecules was examined by contact angle measurements, spectroscopic ellipsometry, infrared, and near edge x-ray absorption fine structure (NEXAFS) spectroscopy. All three molecules displayed rupture forces that agreed with previously reported values for the biotin--avidin rupture. The tripodal molecular tip displayed narrower distribution in their force histograms than the monopodal molecular tip. The performance of the tripodal molecular tip was compared to the monopodal molecular tip in single molecule force spectroscopy studies. Over repeated measurements, the distribution of forces for the monopodal molecular tip shifted to lower forces, whereas the distribution for the tripodal molecular tip remained constant throughout. Loading rate dependence and control experiments further indicated that the rupture forces of the tripod molecular tips were specific to the biotin--NeutrAvidin interaction. The second functionalization method used the photochemical attachment of undecylenic acid to NCD AFM tips. The photochemical attachment of undecylenic acid to hydrogen-terminated NCD wafer surfaces was investigated by contact angle measurements, x

76 FR 63287 - Privacy Act of 1974; System of Records

Science.gov (United States)

2011-10-12

... one command to facilitate collaborative planning and to assist all echelons in achieving situational awareness, and for assisting the Combatant Command and Joint Task Force Surgeon in assessing risks..., Attention: Freedom of Information Act Requester Service Center, 16401 East Centretech Parkway, Aurora, CO...

A novel experimental mechanics method for measuring the light pressure acting on a solar sail membrane

Science.gov (United States)

Shi, Aiming; Jiang, Li; Dowell, Earl H.; Qin, Zhixuan

2017-02-01

Solar sail is a high potential `sailing craft' for interstellar exploration. The area of the first flight solar sail demonstrator named "IKAROS" is 200 square meters. Future interplanetary missions will require solar sails at least on the order of 10000 square meters (or larger). Due to the limitation of ground facilities, the size of experimental sample should not be large. Furthermore the ground experiments have to be conducted in gravitational field, so the gravity effect must be considered in a ground test. To obtain insight into the solar sail membrane dynamics, a key membrane flutter (or limit cycle oscillations) experiment with light forces acting on it must be done. But one big challenge is calibrating such a tiny light force by as a function of the input power. In this paper, a gravity-based measuring method for light pressure acting on membrane is presented. To explain the experimental principle, an ideal example of a laser beam with expanders and a metal film is studied. Based on calculations, this experimental mechanics method for calibrating light pressure with an accuracy of 0.01 micro-Newton may be realized by making the light force balance the gravity force on the metal films. This gravity-based measuring method could not only be applied to study the dynamics characteristics of solar sail membrane structure with different light forces, but could also be used to determine more accurate light forces/loads acting on solar sail films and hence to enhance the determination of the mechanical properties of the solar sail membrane structure.

Lateral Casimir-Polder forces by breaking time-reversal symmetry

Science.gov (United States)

Oude Weernink, Ricardo R. Q. P. T.; Barcellona, Pablo; Buhmann, Stefan Yoshi

2018-03-01

We examine the lateral Casimir-Polder force acting on a circular rotating emitter near a dielectric plane surface. As the circular motion breaks time-reversal symmetry, the spontaneous emission in a direction parallel to the surface is in general anisotropic. We show that a lateral force arises which can be interpreted as a recoil force because of this asymmetric emission. The force is an oscillating function of the distance between the emitter and the surface, and the lossy character of the dielectric strongly influences the results in the near-field regime. The force exhibits also a population-induced dynamics, decaying exponentially with respect to time on time scales of the inverse of the spontaneous decay rate. We propose that this effect could be detected measuring the velocity acquired by the emitter, following different cycles of excitation and spontaneous decay. Our results are expressed in terms of the Green's tensor and can therefore easily be applied to more complex geometries.

Prediction of bubble detachment diameter in flow boiling based on force analysis

International Nuclear Information System (INIS)

Chen Deqi; Pan Liangming; Ren Song

2012-01-01

Highlights: ► All the forces acting on the growing bubbles are taken into account in the model. ► The bubble contact diameter has significant effect on bubble detachment. ► Bubble growth force and surface tension are more significant in narrow channel. ► A good agreement between the predicted and the measured results is achieved. - Abstract: Bubble detachment diameter is one of the key parameters in the study of bubble dynamics and boiling heat transfer, and it is hard to be measured in a boiling system. In order to predict the bubble detachment diameter, a theoretical model is proposed based on forces analysis in this paper. All the forces acting on a bubble are taken into account to establish a model for different flow boiling configurations, including narrow and conventional channels, upward, downward and horizontal flows. A correlation of bubble contact circle diameter is adopted in this study, and it is found that the bubble contact circle diameter has significant effect on bubble detachment. A new correlation taking the bubble contact circle diameter into account for the evaluation of bubble growth force is proposed in this study, and it is found that the bubble growth force and surface tension force are more significant in narrow channel when comparing with that in conventional channel. A visual experiment was carried out in order to verify present model; and the experimental data from published literature are used also. A good agreement between predicted and measured results is achieved.

Forces on particles in microstreaming flows

Science.gov (United States)

Hilgenfeldt, Sascha; Rallabandi, Bhargav; Thameem, Raqeeb

2015-11-01

In various microfluidic applications, vortical steady streaming from ultrasonically driven microbubbles is used in concert with a pressure-driven channel flow to manipulate objects. While a quantitative theory of this boundary-induced streaming is available, little work has been devoted to a fundamental understanding of the forces exerted on microparticles in boundary streaming flows, even though the differential action of such forces is central to applications like size-sensitive sorting. Contrary to other microfluidic sorting devices, the forces in bubble microstreaming act over millisecond times and micron length scales, without the need for accumulated deflections over long distances. Accordingly, we develop a theory of hydrodynamic forces on the fast time scale of bubble oscillation using the lubrication approximation, showing for the first time how particle displacements are rectified near moving boundaries over multiple oscillations in parallel with the generation of the steady streaming flow. The dependence of particle migration on particle size and the flow parameters is compared with experimental data. The theory is applicable to boundary streaming phenomena in general and demonstrates how particles can be sorted very quickly and without compromising device throughput. We acknowledge support by the National Science Foundation under grant number CBET-1236141.

Magnus force in superfluids and superconductors

International Nuclear Information System (INIS)

Sonin, E.B.

1997-01-01

The forces on the vortex, transverse to its velocity, are considered. In addition to the superfluid Magnus force from the condensate (superfluid component), there are transverse forces from thermal quasiparticles and external fields violating the Galilean invariance. The forces between quasiparticles and the vortex originate from interference of quasiparticles with trajectories on the left and on the right from the vortex like similar forces for electrons interacting with the thin magnetic-flux tube (the Aharonov-Bohm effect). These forces are derived for phonons from the equations of superfluid hydrodynamics, and for BCS quasiparticles from the Bogolyubov endash de Gennes equations. The effect of external fields breaking Galilean invariance is analyzed for vortices in the two-dimensional Josephson junction array. The symmetry analysis of the classical equations for the array shows that the total transverse force on the vortex vanishes. Therefore the Hall effect which is linear in the transverse force is absent also. This means that the Magnus force from the superfluid component exactly cancels with the transverse force from the external fields. The results of other approaches are also brought together for discussion. copyright 1997 The American Physical Society

A Fifth Force: Generalized through Superconductors

Science.gov (United States)

Robertson, Glen A.

1999-01-01

The connection between the Biefield-Brown Effect, the recent repeat of the 1902 Trouton-Noble (TN) experiments, and the gravity shielding experiments was explored. This connection is visualized through high capacitive electron concentrations. From this connection, a theory is proposed that connects mass energy to gravity and a fifth force. The theory called the Gravi-Atomic Energy theory presents two new terms: Gravi-atomic energy and quantum vacuum pressure (QVP). Gravi-atomic energy is defined as the radiated mass energy, which acts on vacuum energy to create a QVP about a mass, resulting in gravity and the fifth force. The QVP emission from a superconductor was discussed followed by the description of a test for QVP from a superconductor using a Cavendish balance.

Internal-external malalignment of the femoral component in kinematically aligned total knee arthroplasty increases tibial force imbalance but does not change laxities of the tibiofemoral joint.

Science.gov (United States)

Riley, Jeremy; Roth, Joshua D; Howell, Stephen M; Hull, Maury L

2018-06-01

The purposes of this study were to quantify the increase in tibial force imbalance (i.e. magnitude of difference between medial and lateral tibial forces) and changes in laxities caused by  2° and 4° of internal-external (I-E) malalignment of the femoral component in kinematically aligned total knee arthroplasty. Because I-E malalignment would introduce the greatest changes to the articular surfaces near 90° of flexion, the hypotheses were that the tibial force imbalance would be significantly increased near 90° flexion and that primarily varus-valgus laxity would be affected near 90° flexion. Kinematically aligned TKA was performed on ten human cadaveric knee specimens using disposable manual instruments without soft tissue release. One 3D-printed reference femoral component, with unmodified geometry, was aligned to restore the native distal and posterior femoral joint lines. Four 3D-printed femoral components, with modified geometry, introduced I-E malalignments of 2° and 4° from the reference component. Medial and lateral tibial forces were measured from 0° to 120° flexion using a custom tibial force sensor. Bidirectional laxities in four degrees of freedom were measured from 0° to 120° flexion using a custom load application system. Tibial force imbalance increased the greatest at 60° flexion where a regression analysis against the degree of I-E malalignment yielded sensitivities (i.e. slopes) of 30 N/° (medial tibial force > lateral tibial force) and 10 N/° (lateral tibial force > medial tibial force) for internal and external malalignments, respectively. Valgus laxity increased significantly with the 4° external component with the greatest increase of 1.5° occurring at 90° flexion (p < 0.0001). With the tibial component correctly aligned, I-E malalignment of the femoral component caused significant increases in tibial force imbalance. Minimizing I-E malalignment lowers the increase in the tibial force imbalance. By keeping

The study of dynamic force acted on water strider leg departing from water surface

Directory of Open Access Journals (Sweden)

Peiyuan Sun

2018-01-01

Full Text Available Water-walking insects such as water striders can skate on the water surface easily with the help of the hierarchical structure on legs. Numerous theoretical and experimental studies show that the hierarchical structure would help water strider in quasi-static case such as load-bearing capacity. However, the advantage of the hierarchical structure in the dynamic stage has not been reported yet. In this paper, the function of super hydrophobicity and the hierarchical structure was investigated by measuring the adhesion force of legs departing from the water surface at different lifting speed by a dynamic force sensor. The results show that the adhesion force decreased with the increase of lifting speed from 0.02 m/s to 0.4 m/s, whose mechanic is investigated by Energy analysis. In addition, it can be found that the needle shape setae on water strider leg can help them depart from water surface easily. Thus, it can serve as a starting point to understand how the hierarchical structure on the legs help water-walking insects to jump upward rapidly to avoid preying by other insects.

Analysis of the tractive force pattern on a knot by force measurement during laparoscopic knot tying.

Science.gov (United States)

Takayasu, Kenta; Yoshida, Kenji; Kinoshita, Hidefumi; Yoshimoto, Syunsuke; Oshiro, Osamu; Matsuda, Tadashi

2017-07-19

Quantifying surgical skills assists novice surgeons when learning operative techniques. We measured the interaction force at a ligation point and clarified the features of the force pattern among surgeons with different skill levels during laparoscopic knot tying. Forty-four surgeons were divided into three groups based on experience: 13 novice (0-5 years), 16 intermediate (6-15 years), and 15 expert (16-30 years). To assess the tractive force direction and volume during knot tying, we used a sensor that measures six force-torque values (x-axis: Fx, y-axis: Fy, z-axis: Fz, and xy-axis: Fxy) attached to a slit Penrose drain. All participants completed one double knot and five single knot sequences. We recorded completion time, force volume (FV), maximum force (MF), time over 1.5 N, duration of non-zero force, and percentage time when vertical force exceeded horizontal force (PTz). There was a significant difference between groups for completion time (p = 0.007); FV (total: p = 0.002; Fx: p = 0.004, Fy: p = 0.007, Fxy: p = 0.004, Fz: p force (p = 0.029); and PTz (p force pattern at the ligation point during suturing by surgeons with three levels of experience using a force measurement system. We revealed that both force volume and force direction differed depending on surgeons' skill level during knot tying. Copyright © 2017. Published by Elsevier Inc.

Color van der Waals force acting in heavy-ion scattering at low energies

International Nuclear Information System (INIS)

Hussein, M.S.; Lima, C.L.; Pato, M.P.; Bertulani, C.A.

1990-01-01

The influence of the color van der Waals force in the elastic scattering of 208 Pb on 208 Pb at sub-barrier energies is studied. The conspicuous changes in the Mott oscillation found here are suggested as a possible experimental test

Slovak Republic Act No. 409/2006 Coll. of 24 June 2006 on waste and amending some laws

International Nuclear Information System (INIS)

2006-01-01

This Act into system of law of the Slovak Republic were exrogared the legal acts of the European Communities listed in the Annex 1. This Act regulates the competence of state administration and municipalities, the rights and obligations of legal entities and individuals in preventing waste and in waste management, liability for breach of obligations in the waste management and the establishment of the Recycling Fund. This Act came into force on July 1, 2006.

Ontario gas prices review task force report : fairness at the pump

International Nuclear Information System (INIS)

2000-01-01

Sudden gas price increases hit Ontario consumers in July 1999, and as a result, the Gas Busters Hotline operated by the provincial government received over 4,000 complaints concerning the price of gas. World crude oil prices increased to above 34 American dollars per barrel by March 2000, and there were discrepancies by as much as 10 cents a litre in the price of gas in Ontario, depending on the community where the purchase was made. The Gas Prices Review Task Force was established in November 1999 to assist in the identification of an adequate solution to the rising price of gas. Public participation was sought, as well as input from representatives of consumer groups and industry. The Task Force was also mandated to conduct policy options research to ensure fair prices at the pump, to examine the regulatory or legislative initiatives that would work best for the protection of the consumer, in accordance with the federal Competition Act. A report was submitted to the Minister of Consumer and Commercial Relations. A total of fourteen recommendations were made to the Minister. The recommendations touched topics as varied as tax collection legislation, price monitoring, segmented earnings reports, removal of the Goods and Services Tax (GST). refs., figs

Air traffic security act unconstitutional; Luftsicherheitsgesetz verfassungswidrig

Energy Technology Data Exchange (ETDEWEB)

Heller, W.

2006-05-15

In the interest of more effective protective measures against terrorist attacks, the German federal parliament inter alia added a clause to the Air Traffic Security Act (Sec. 14, Para. 3, Air Traffic Security Act) empowering the armed forces to shoot down aircraft to be used as a weapon against human lives. In Germany, this defense possibility has been discussed also in connection with deliberate crashes of hijacked aircraft on nuclear power plants. The 1{sup st} Division of the German Federal Constitutional Court, in its decision of February 15, 2006, ruled that Sec. 14, Para. 3, Air Traffic Security Act was incompatible with the Basic Law and thus was null and void (file No. 1 BvR 357/05) for two reasons: - There was no legislative authority on the part of the federal government. - The provision was incompatible with the basic right of life and the guarantee of human dignity as enshrined in the Basic Law. (orig.)

Muscle response to pneumatic hand tool torque reaction forces.

Science.gov (United States)

Radwin, R G; VanBergeijk, E; Armstrong, T J

1989-06-01

Surface electromyography was used for studying the effects of torque reaction force acting against the hand, on forearm muscle activity and grip force for five subjects operating right angle, air shut-off nutrunners. Four tools having increasing spindle torque were operated using short and long torque reaction times. Nutrunner spindle torque ranged between 30 Nm and 100 Nm. Short torque reaction time was considered 0.5 s while long torque reaction time was 2 s. Peak horizontal force was the greatest component of the reaction force acting against the hand and accounted for more than 97% of the peak resultant hand force. Peak hand force increased from 89 N for the smallest tool to 202 N for the largest tool. Forearm muscle rms EMG, scaled for grip force, indicated average flexor activity during the Torque-reaction phase was more than four times greater than the Pre-start and Post Shut-off phases, and two times greater than the Run-down phase. Flexor EMG activity during the Torque-reaction phase increased for increasing tool peak spindle torque. Average flexor rms EMG activity, scaled for grip force, during the Torque-reaction phase increased from 372 N for the 30 Nm nutrunner to 449 N for the 100 Nm nutrunner. Flexor rms EMG activity averaged during the Torque-reaction phase and scaled for grip force was 390 N for long torque reaction times and increased to 440 N for short torque reaction times. Flexor rms EMG integrated over the torque reaction phase was 839 Ns for long torque reaction times and decreased to 312 Ns for short torque reaction times. The average latency between tool spindle torque onset and peak initial flexor rms EMG for long torque reaction times was 294 ms which decreased to 161 ms for short torque reaction times. The average latency between peak tool spindle torque, just prior to tool shut-off, and peak final rms EMG for long torque reaction times was 97 ms for flexors and 188 ms for extensors, which decreased for short torque reaction times to 47

Heisenberg equation for a nonrelativistic particle on a hypersurface: From the centripetal force to a curvature induced force

Directory of Open Access Journals (Sweden)

D. K. Lian

2017-12-01

Full Text Available In classical mechanics, a nonrelativistic particle constrained on an N − 1 curved hypersurface embedded in N flat space experiences the centripetal force only. In quantum mechanics, the situation is totally different for the presence of the geometric potential. We demonstrate that the motion of the quantum particle is ”driven” by not only the centripetal force, but also a curvature induced force proportional to the Laplacian of the mean curvature, which is fundamental in the interface physics, causing curvature driven interface evolution.

Report of the HDA building Task Force.

Science.gov (United States)

Scheerer, Ernest W

2006-01-01

The Building Task Force, after researching the many options, recommended to the Board of Trustees that, at this time, it is in the best interest of the association and its members to keep the building. In addition to the reasons outlined in the preceding paragraphs, the conclusions drawn by the Task Force can be summarized as follows: 1) This is not the time to make a change as both land and construction costs are high; 2) There is little inventory at this time that would provide a significant improvement over the present building; 3) There is no urgent need to act now; and 4) Cost-effective changes can be made to make the building more valuable to the association.

Measurements of dispersion forces between colloidal latex particles with the atomic force microscope and comparison with Lifshitz theory

Energy Technology Data Exchange (ETDEWEB)

Elzbieciak-Wodka, Magdalena; Ruiz-Cabello, F. Javier Montes; Trefalt, Gregor; Maroni, Plinio; Borkovec, Michal, E-mail: michal.borkovec@unige.ch [Department of Inorganic and Analytical Chemistry, University of Geneva, Sciences II, 30, Quai Ernest-Ansermet, 1205 Geneva (Switzerland); Popescu, Mihail N. [Ian Wark Research Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia)

2014-03-14

Interaction forces between carboxylate colloidal latex particles of about 2 μm in diameter immersed in aqueous solutions of monovalent salts were measured with the colloidal probe technique, which is based on the atomic force microscope. We have systematically varied the ionic strength, the type of salt, and also the surface charge densities of the particles through changes in the solution pH. Based on these measurements, we have accurately measured the dispersion forces acting between the particles and estimated the apparent Hamaker constant to be (2.0 ± 0.5) × 10{sup −21} J at a separation distance of about 10 nm. This value is basically independent of the salt concentration and the type of salt. Good agreement with Lifshitz theory is found when roughness effects are taken into account. The combination of retardation and roughness effects reduces the value of the apparent Hamaker constant and its ionic strength dependence with respect to the case of ideally smooth surfaces.

The Symbiotic Relationship between the Air Force’s Active and Reserve Components: Ensuring the Health of the Total Force

Science.gov (United States)

2013-02-01

2009), 3, http://www.gao.gov/ assets /100/96269.pdf. 22. Department of Defense Human Resources Management, “ Human Resources Manage- ment ( HRM ) Community of...rotating forces.20 Predictability is especially important to obtaining RC partici- pation in the absence of mobilization authority by allowing...continuum of service construct to reduce legal and policy barriers be- tween the components. This construct mandates “a Human Capital strategy allowing

IDEAL BRAKE FORCE DISTRIBUTION BETWEEN THE AXLES OF THE TWO-AXLE VEHICLE SERVICE BRAKE APPLICATIONS

Directory of Open Access Journals (Sweden)

M. Podryhalo

2015-07-01

Full Text Available The obtained analytical expressions allow us to evaluate the stability of two-axle vehicles at various slowdowns. An analytical expression for calculating the ideal according to condition stability ensuring of a two-axle vehicle at service brake applications of brake force distribution allows to offer automatic control devices for brake force adjucement. With decellerationg growth of the two-axle vehicle at service braking the braking force acting on the front axle should decrease relative to the brake force on the rear axle.

FDTD simulations of forces on particles during holographic assembly.

Science.gov (United States)

Benito, David C; Simpson, Stephen H; Hanna, Simon

2008-03-03

We present finite-difference time-domain (FDTD) calculations of the forces and torques on dielectric particles of various shapes, held in one or many Gaussian optical traps, as part of a study of the physical limitations involved in the construction of micro- and nanostructures using a dynamic holographic assembler (DHA). We employ a full 3-dimensional FDTD implementation, which includes a complete treatment of optical anisotropy. The Gaussian beams are sourced using a multipole expansion of a fifth order Davis beam. Force and torques are calculated for pairs of silica spheres in adjacent traps, for silica cylinders trapped by multiple beams and for oblate silica spheroids and calcite spheres in both linearly and circularly polarized beams. Comparisons are drawn between the magnitudes of the optical forces and the Van der Waals forces acting on the systems. The paper also considers the limitations of the FDTD approach when applied to optical trapping.

Self-force as probe of internal structure

International Nuclear Information System (INIS)

Isoyama, Soichiro; Poisson, Eric

2012-01-01

The self-force acting on a (scalar or electric) charge held in place outside a massive body contains information about the body's composition, and can therefore be used as a probe of internal structure. We explore this theme by computing the (scalar or electromagnetic) self-force when the body is a spherical ball of perfect fluid in hydrostatic equilibrium, under the assumption that its rest-mass density and pressure are related by a polytropic equation of state. The body is strongly self-gravitating, and all computations are performed in exact general relativity. The dependence on internal structure is best revealed by expanding the self-force in powers of r -1 0 , with r 0 denoting the radial position of the charge outside the body. To the leading order, the self-force scales as r -3 0 and depends only on the square of the charge and the body's mass; the leading self-force is universal. The dependence on internal structure is seen at the next order, r -5 0 , through a structure factor that depends on the equation of state. We compute this structure factor for relativistic polytropes, and show that for a fixed mass, it increases linearly with the body's radius in the case of the scalar self-force, and quadratically with the body's radius in the case of the electromagnetic self-force. In both cases we find that for a fixed mass and radius, the self-force is smaller if the body is more centrally dense, and larger if the mass density is more uniformly distributed. (paper)

Actuator forces in CFD: RANS and LES modeling in OpenFOAM

International Nuclear Information System (INIS)

Schito, P; Zasso, A

2014-01-01

Wind turbine wakes are a very challenging topic for scientific computations, but modern CFD frameworks and latest HPC centers allow setting up numerical computations on the wake induced by the wind turbine. The main issues is that the correct modeling of the wake is related to the correct modeling of the interaction between the blade and the incoming flow. The aim of the proposed work is to estimate the aerodynamic forces acting on the blades in order to correctly generate the rotor wake applying equivalent aerodynamic force source on the flow. The definition of a blade forces is done developing a model able to correctly estimate this aerodynamic forces as a function of the local flow seen by the blade during its revolution

76 FR 18737 - Reserve Forces Policy Board (RFPB) Member Solicitation

Science.gov (United States)

2011-04-05

..., abolished the Civilian Components Policy Board in June, 1951 and created the Reserve Forces Policy Board... military education, joint qualification, and joint operations matters. The Federal Advisory Committee Act... and 102-3) provide the basis for and guidance concerning the management and operation of Federal...

How small bugs tie down big rocks: Measuring and modeling the forces acting between nets spun by Caddisfly larvae (Hydropsychidae) and gravel particles at the onset of motion

Science.gov (United States)

Mclaughlin, M. K.; Tumolo, B.; Sklar, L. S.; Albertson, L.; Daniels, M.

2017-12-01

The influence of life on geomorphic processes is commonly inferred from correlations between the size and abundance of individual organisms and the change in process thresholds and rates from abiotic conditions. However, to understand and model the underlying mechanisms, it is helpful to make direct measurements of the forces acting between organisms and the earth materials they inhabit. For example, flume studies have found that the presence of net-spinning caddisfly larvae (Trichoptera: Hydropsychidae) can increase the shear stress required to initiate particle motion by more than a factor of two, with potentially significant implications for the timing and magnitude of bedload sediment transport in gravel-bedded rivers. To explore the underlying mechanics we conducted flume experiments at the Stroud Water Research center in Avonadale, Pennsylvania, using strain gages to measure the forces acting between caddisfly nets and sediment particles of various sizes, during the process of initial particle motion. We combine these measurements with high-speed video images to document for the first time, the three dimensional dynamics of net stretching, tearing, and detachment that govern the magnitude of the increase in critical shear stress. We are using these data and insights to substantially improve a previously published theoretical model for the mechanics of sediment stabilization by caddisfly larvae. In particular, we seek to constrain the range of particle sizes potentially stabilized by caddisfly larvae and explain mechanistically why the effect of caddisfly nets varies with particle size. These predictions have implications for understanding feedbacks between bed stabilization by caddisflies, insect density, inter-specific niche partitioning, and the movement of sediment that shapes gravel-bed channels.

Strength decoupling from the giant dipole resonance upon diagonalizing a Gaussian force and a delta-force on a particle-hole basis

International Nuclear Information System (INIS)

Csernai, L.P.; Zimanyi, J.; Gyarmati, B.; Lovas, R.G.

1978-01-01

The finite-range Gaussian force and delta-force have been diagonalized in a basis of 27 particle-hole states with Jsup(π)=1 - in 116 Sn. Depending on the range of the force, 3.9-7.1% of the total transition rate has been found in the 6-9 MeV excitation energy region, which comprises the unperturbed energies of the basis states containing neutron threshold states. (Auth.)

Biomechanical forces promote embryonic haematopoiesis

Science.gov (United States)

Adamo, Luigi; Naveiras, Olaia; Wenzel, Pamela L.; McKinney-Freeman, Shannon; Mack, Peter J.; Gracia-Sancho, Jorge; Suchy-Dicey, Astrid; Yoshimoto, Momoko; Lensch, M. William; Yoder, Mervin C.; García-Cardeña, Guillermo; Daley, George Q.

2009-01-01

Biomechanical forces are emerging as critical regulators of embryogenesis, particularly in the developing cardiovascular system1,2. After initiation of the heartbeat in vertebrates, cells lining the ventral aspect of the dorsal aorta, the placental vessels, and the umbilical and vitelline arteries initiate expression of the transcription factor Runx1 (refs 3–5), a master regulator of haematopoiesis, and give rise to haematopoietic cells4. It remains unknown whether the biomechanical forces imposed on the vascular wall at this developmental stage act as a determinant of haematopoietic potential6. Here, using mouse embryonic stem cells differentiated in vitro, we show that fluid shear stress increases the expression of Runx1 in CD41+c-Kit+ haematopoietic progenitor cells7,concomitantly augmenting their haematopoietic colony-forming potential. Moreover, we find that shear stress increases haematopoietic colony-forming potential and expression of haematopoietic markers in the paraaortic splanchnopleura/aorta–gonads–mesonephros of mouse embryos and that abrogation of nitric oxide, a mediator of shear-stress-induced signalling8, compromises haematopoietic potential in vitro and in vivo. Collectively, these data reveal a critical role for biomechanical forces in haematopoietic development. PMID:19440194

75 FR 77849 - Privacy Act of 1974; System of Records

Science.gov (United States)

2010-12-14

... Agency, Defense Threat Reduction Agency, Missile Defense Organization, Pentagon Force Protection Agency... DEPARTMENT OF DEFENSE Office of the Secretary [Docket ID: DOD-2010-OS-0160] Privacy Act of 1974; System of Records AGENCY: Office of the Secretary of Defense, DoD. ACTION: Notice to add a system of...

77 FR 77049 - Privacy Act of 1974; System of Records

Science.gov (United States)

2012-12-31

..., Air Force Privacy Act Office, Office of Warfighting Integration and Chief Information officer, ATTN... of 1974 (5 U.S.C. 552a), as amended, which requires the submission of a new or altered system report...). Reason The Innovative Development through Employee Awareness (IDEA) Program Data System (IPDS) has been...

Study on estimating fluid force acting on a hull during maneuvering movement; Soju undoji no sentai ni sayosuru ryutairyoku no suitei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yukawa, K; Kijima, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1997-10-01

With types of general cargo vessel and VLCC vessel as the object of discussion, a method was discussed to estimate fluid force acting theoretically on a hull during maneuvering movement, taking frame line shape into consideration. A vortex model was improved by giving consideration of time-based decay on intensity of discrete vortex lines based on the Rankine vortex. Modeling of flow fields around a hull was attempted to deal with movements in which width and draft are small as compared with the ship length, and turning angle speed and deviation angle are small. It was assumed that the ship speed is slow and effects of waves can be disregarded. Specular images of the hull were taken with regard to free surface, and handled as a double body model. Speed potential to express flow fields around a hull is required to satisfy the following five boundary conditions of Laplace, substance surface, free vortex layers, infinity and exfoliation. The potential may be handled as a two-dimensional problem in a field near the hull by using assumption of a slender and long body and conformal mapping. It was found possible to estimate hull fluid force with relatively good accuracy. Fine linear coefficients derived from the estimation were used to have performed highly accurate determination on course stabilization. 5 refs., 6 figs., 2 tabs.

Forces on a magnet moving past figure-eight coils

International Nuclear Information System (INIS)

Mulcahy, T.H.; He, Jianliang; Rote, D.M.; Rossing, T.D.

1993-01-01

For the first time, the lift, drag, and guidance forces acting on a permanent magnet are measured as the magnet passes over different arrays of figure-eight (null-flux) coils. The experimental results are in good agreement with the predictions of dynamic circuit theory, which is used to explain more optimal coil arrays

Self-force calculations with matched expansions and quasinormal mode sums

International Nuclear Information System (INIS)

Casals, Marc; Dolan, Sam; Ottewill, Adrian C.; Wardell, Barry

2009-01-01

Accurate modeling of gravitational wave emission by extreme-mass ratio inspirals is essential for their detection by the LISA mission. A leading perturbative approach involves the calculation of the self-force acting upon the smaller orbital body. In this work, we present the first application of the Poisson-Wiseman-Anderson method of 'matched expansions' to compute the self-force acting on a point particle moving in a curved spacetime. The method employs two expansions for the Green function, which are, respectively, valid in the 'quasilocal' and 'distant past' regimes, and which may be matched together within the normal neighborhood. We perform our calculation in a static region of the spherically symmetric Nariai spacetime (dS 2 xS 2 ), in which scalar-field perturbations are governed by a radial equation with a Poeschl-Teller potential (frequently used as an approximation to the Schwarzschild radial potential) whose solutions are known in closed form. The key new ingredients in our study are (i) very high order quasilocal expansions and (ii) expansion of the distant past Green function in quasinormal modes. In combination, these tools enable a detailed study of the properties of the scalar-field Green function. We demonstrate that the Green function is singular whenever x and x ' are connected by a null geodesic, and apply asymptotic methods to determine the structure of the Green function near the null wave front. We show that the singular part of the Green function undergoes a transition each time the null wave front passes through a caustic point, following a repeating fourfold sequence δ(σ), 1/πσ, -δ(σ), -1/πσ, etc., where σ is Synge's world function. The matched-expansion method provides insight into the nonlocal properties of the self-force. We show that the self-force generated by the segment of the worldline lying outside the normal neighborhood is not negligible. We apply the matched-expansion method to compute the scalar self-force acting on

Gait analysis after successful mobile bearing total ankle replacement.

NARCIS (Netherlands)

Doets, H.C.; van Middelkoop, M.; Houdijk, J.H.P.; Nelissen, R.G.; Veeger, H.E.J.

2007-01-01

Background: The effect of total ankle replacement on gait is not fully known in terms of joint kinematics, ground reaction force, and activity of the muscles of the lower leg. Methods: A comparative gait study was done in 10 patients after uneventful unilateral mobile-bearing total ankle replacement

Soft-tissue tension total knee arthroplasty.

Science.gov (United States)

Asano, Hiroshi; Hoshino, Akiho; Wilton, Tim J

2004-08-01

It is far from clear how best to define the proper strength of soft-tissue tensioning in total knee arthroplasty (TKA). We attached a torque driver to the Monogram balancer/tensor device and measured soft-tissue tension in full extension and 90 degrees flexion during TKA. In our surgical procedure, when we felt proper soft-tissue tension was being applied, the mean distraction force was noted to be 126N in extension and 121N in flexion. There was no significant correlation between soft-tissue tension and the postoperative flexion angle finally achieved. To the best of our knowledge, this is the first study to assess the actual distraction forces in relation to soft-tissue tension in TKA. Further study may reveal the most appropriate forces to achieve proper soft-tissue tension in the wide variety of circumstances presenting at knee arthroplasty.

The procedure for granting concessions under the Concessions Act of Republika Srpska

Directory of Open Access Journals (Sweden)

Borojević Klaudia

2015-01-01

Full Text Available The Concessions Act of Republic of Srpska entered into force in 2002. By the adoption of this Act, consessions were exteacted from the Foreign Investments Act and given significantly more attention than in the former period. As legal practice imposed the need for frequent changes of this Act, the new Concessions Act of Republica Srpska was enacted on 15th July 2013. The current legal provisions on concessions in B&H have been modelled on the recognized international standards but they still do not provide sufficient guarantees to foreign investors willing to invest their capital in infrastructure projects in Bosnia and Hercegovina. The types of concessions are clearly defined but there are many other reasons influencing the investment of foreign capital and conclusion of a concession contract, the most prominent of which are the political climate and economic stability.

ACT: A Benchmark for College Readiness, 2007-2011

Science.gov (United States)

Uzzell, Renata; Lewis, Sharon; Simon, Candace; Palacios, Moses; Guzman, Amilcar; Casserly, Michael

2012-01-01

This report was prepared by the Council of Great City Schools in collaboration with ACT to collect and analyze urban student performance between 2007 and 2011 and to examine student achievement by race and gender. Following is a summary of the study's findings: (1) The total number of ACT test takers increased both nationally and in CGCS districts…

Projected Costs of U.S. Nuclear Forces, 2017 to 2026

Science.gov (United States)

2017-02-01

amounts at roughly the same rates that costs for similar programs have grown in the past. Nuclear forces account for roughly 6 percent of the total 10...nuclear forces, some published estimates of the total costs of nuclear weapons account for the costs of several related activities. Examples include...based its estimate on historical costs of analogous programs. b. This category includes nuclear-related research and operations support activities by

Prediction of medial and lateral contact force of the knee joint during normal and turning gait after total knee replacement.

Science.gov (United States)

Purevsuren, Tserenchimed; Dorj, Ariunzaya; Kim, Kyungsoo; Kim, Yoon Hyuk

2016-04-01

The computational modeling approach has commonly been used to predict knee joint contact forces, muscle forces, and ligament loads during activities of daily living. Knowledge of these forces has several potential applications, for example, within design of equipment to protect the knee joint from injury and to plan adequate rehabilitation protocols, although clinical applications of computational models are still evolving and one of the limiting factors is model validation. The objective of this study was to extend previous modeling technique and to improve the validity of the model prediction using publicly available data set of the fifth "Grand Challenge Competition to Predict In Vivo Knee Loads." A two-stage modeling approach, which combines conventional inverse dynamic analysis (the first stage) with a multi-body subject-specific lower limb model (the second stage), was used to calculate medial and lateral compartment contact forces. The validation was performed by direct comparison of model predictions and experimental measurement of medial and lateral compartment contact forces during normal and turning gait. The model predictions of both medial and lateral contact forces showed strong correlations with experimental measurements in normal gait (r = 0.75 and 0.71) and in turning gait trials (r = 0.86 and 0.72), even though the current technique over-estimated medial compartment contact forces in swing phase. The correlation coefficient, Sprague and Geers metrics, and root mean squared error indicated that the lateral contact forces were predicted better than medial contact forces in comparison with the experimental measurements during both normal and turning gait trials. © IMechE 2016.

Defect forces, defect couples and path integrals in fracture mechanics

International Nuclear Information System (INIS)

Roche, R.L.

1979-07-01

In this work, it is shown that the path integrals can be introduced without any reference to the material behavior. The method is based on the definition in a continuous medium of a set of vectors and couples having the dimension of a force or a moment. More precisely, definitions are given of volume defect forces, surface defect forces, volume defect couples, and surface defect couples. This is done with the help of the stress working variation of a particule moving through the solid. The most important result is: the resultant of all the defect forces included in a volume V is the J integral on the surface surrounding V and the moment resultant is the L integral. So these integrals are defined without any assumption on the material constitutive equation. Another result is the material form of the virtual work principle - defect forces are acting like conventional forces in the conventional principles of virtual work. This lead to the introduction of the energy momentum tensor and of the associated couple stress. Application of this method is made to fracture mechanics in studying the defect forces distribution around a crack [fr

Gravitomagnetic field of the universe and Coriolis force on the rotating Earth

International Nuclear Information System (INIS)

Veto, B

2011-01-01

The Machian effect of distant masses of the universe in the frame of reference of the rotating Earth is demonstrated using the gravitomagnetic approach of general relativity. This effect appears in the form of a gravitomagnetic Lorentz force acting on moving bodies on the Earth. The gravitomagnetic field of the universe-deduced from a simple model-exerts a gravitomagnetic Lorentz force on moving bodies, a force parallel to and with comparable strength to the Coriolis force observed on the rotating Earth. It seems after simple considerations that the Coriolis force happens to be the gravitomagnetic Lorentz force exerted by the mass of a black hole universe. The description of the phenomenon is simpler using the gravitomagnetic approach than the standard formulation of general relativity, so the method relying on gravitomagnetism is advisable in lectures intended for master's degree level physics students and advanced undergraduates.

Bio-inspired ciliary force sensor for robotic platforms

KAUST Repository

Ribeiro, Pedro; Khan, Mohammed Asadullah; Alfadhel, Ahmed; Kosel, Jü rgen; Franco, Fernando; Cardoso, Susana; Bernardino, Alexandre; Schmitz, Alexander; Santos-Victor, Jose; Jamone, Lorenzo

2017-01-01

The detection of small forces is of great interest in any robotic application that involves interaction with the environment (e.g., objects manipulation, physical human-robot interaction, minimally invasive surgery), since it allows the robot to detect the contacts early on and to act accordingly. In this letter, we present a sensor design inspired by the ciliary structure frequently found in nature, consisting of an array of permanently magnetized cylinders (cilia) patterned over a giant magnetoresistance sensor (GMR). When these cylinders are deformed in shape due to applied forces, the stray magnetic field variation will change the GMR sensor resistivity, thus enabling the electrical measurement of the applied force. In this letter, we present two 3 mm × 3 mm prototypes composed of an array of five cilia with 1 mm of height and 120 and 200 μm of diameter for each prototype. A minimum force of 333 μN was measured. A simulation model for determining the magnetized cylinders average stray magnetic field is also presented.

Bio-inspired ciliary force sensor for robotic platforms

KAUST Repository

Ribeiro, Pedro

2017-01-20

The detection of small forces is of great interest in any robotic application that involves interaction with the environment (e.g., objects manipulation, physical human-robot interaction, minimally invasive surgery), since it allows the robot to detect the contacts early on and to act accordingly. In this letter, we present a sensor design inspired by the ciliary structure frequently found in nature, consisting of an array of permanently magnetized cylinders (cilia) patterned over a giant magnetoresistance sensor (GMR). When these cylinders are deformed in shape due to applied forces, the stray magnetic field variation will change the GMR sensor resistivity, thus enabling the electrical measurement of the applied force. In this letter, we present two 3 mm × 3 mm prototypes composed of an array of five cilia with 1 mm of height and 120 and 200 μm of diameter for each prototype. A minimum force of 333 μN was measured. A simulation model for determining the magnetized cylinders average stray magnetic field is also presented.

Radiation Protection Act promulgated on May 19, 1988, SFS 1988: 220

International Nuclear Information System (INIS)

1988-01-01

This Act entered into force on 1 July 1988 and supersedes the previous Radiation Protection Act (SFS 1958: 110). The objective of the new Act is to protect humans, animals and the environment from the harmful effects of ionizing as well as non-ionizing radiation. As previously, the main responsibility for public radiation protection will rest with one central radiation protection authority. The general obligations with regard to radiation protection place a greater responsibility than in the past on persons carrying out activities involving radiation. The Act also contains rules governing decommissioning of technical equipment which could generate radiation. Basically, the same requirements still apply regarding licensing of activities involving ionizing radiation, with certain extensions covering, inter alia, also production and transportation of radioactive material. Under the Act, it is now possible to adjust the licensing and supervisory procedures to the level of danger of the radiation source and the need for adequate competence, etc., and finally, more effective supervision is provided for. (NEA) [fr

Classical description of dynamical many-body systems with central forces, spin-orbit forces and spin-spin forces

International Nuclear Information System (INIS)

Goepfert, A.

1994-01-01

This thesis develops a new model, and related numerical methods, to describe classical time-dependent many-body systems interacting through central forces, spin-orbit forces and spin-spin forces. The model is based on two-particle interactions. The two-body forces consist of attractive and repulsive parts. In this model the investigated multi-particle systems are self-bound. Also the total potential of the whole ensemble is derived from the two-particle potential and is not imposed 'from outside'. Each particle has the three degrees of freedom of its centre-of-mass motion and the spin degree of freedom. The model allows for the particles to be either charged or uncharged. Furthermore, each particle has an angular momentum, an intrinsic spin, and a magnetic dipole moment. Through the electromagnetic forces between these charges and moments there arise dynamical couplings between them. The internal interactions between the charges and moments are well described by electromagnetic coupling mechanisms. In fact, compared to conventional classical molecular dynamics calculations in van der Waals clusters, which have no spin degrees of freedom, or for Heisenberg spin Systems, which have no orbital degrees of freedom, the model presented here contains both types of degrees of freedom with a highly non-trivial coupling. The model allows to study the fundamental effects resulting from the dynamical coupling of the spin and the orbital-motion sub-systems. In particular, the dynamics of the particle mass points show a behaviour basically different from the one of particles in a potential with only central forces. Furthermore, a special type of quenching procedure was invented, which tends to drive the multi-particle Systems into states with highly periodic, non-ergodic behaviour. Application of the model to cluster simulations has provided evidence that the model can also be used to investigate items like solid-to-liquid phase transitions (melting), isomerism and specific heat

Complimentary Force Allocation Control for a Dual-Mover Linear Switched Reluctance Machine

Directory of Open Access Journals (Sweden)

J. F. Pan

2017-12-01

Full Text Available This paper inspects the complementary force allocation control schemes for an integrated, dual-mover linear switched reluctance machine (LSRM. The performance of the total force is realized by the coordination of the two movers. First, the structure and characteristics of the LSRM are investigated. Then, a complimentary force allocation control scheme for the two movers is proposed. Next, three force allocation methods—constant proportion, constant proportion with a saturation interval and error compensation, and the variable proportion allocation strategies—are proposed and analyzed, respectively. Experimental results demonstrate that the complimentary force interaction between the two movers can effectively reduce the total amount of force ripples from each method. The results under the variable proportion method also show that dynamic error values falling into 0.044 mm and −0.04 mm under the unit ramp force reference can be achieved. With the sinusoidal force reference with an amplitude of 60 N and a frequency of 0.5 Hz, a dynamic force control precision of 0.062 N and 0.091 N can also be obtained.

Self-Evident Truths: Why We Can Stop Worrying and Love the Posse Comitatus Act

National Research Council Canada - National Science Library

Gentry, Chris R

2008-01-01

This paper asserts that U.S. Government policy prohibiting active participation of the Armed Forces in civilian law enforcement operations, codified in the Posse Comitatus Act of 1878, should remain intact...

77 FR 76861 - Removal of Job Training Partnership Act Implementing Regulations

Science.gov (United States)

2012-12-31

..., 633, 634, 636, 637, and 638 RIN 1205-AB68 Removal of Job Training Partnership Act Implementing...=FR . SUPPLEMENTARY INFORMATION: I. Direct Final Rule Procedure Since removal of the Job Training... barriers to employment for participation in the labor force by providing job training and other services...

Laboratory experiments inform iceberg-calving forces

Science.gov (United States)

Cathles, L. M.; Burton, J. C.

2013-12-01

Globally detected glacial earthquakes are produced during cubic-kilometer scale calving events. The mechanism producing these earthquakes and the dependence of the seismic moment on iceberg size and glacial calving front geometry are not well established. We use a laboratory-scale model of the post-fracture calving process to measure aspects of the calving process not observable in nature. In our experiments, buoyant plastic blocks rest against against a force plate (glacial terminus) which measures both the total force and the torque exerted during the calving process. The blocks are gravitationally unstable, so that they will spontaneously capsize and rotate away from the terminus. We find that hydrodynamics are crucial when considering the coupling between the calving process and the solid earth. There is both a pushing contact force and a simultaneous pulling hydrodynamic force created by a reduced pressure along the terminus face. This suggests that a single couple force mechanism is a more appropriate mode for glacial earthquakes than the commonly used centroid single force model.

Mechanical forces as information: an integrated approach to plant and animal development

Directory of Open Access Journals (Sweden)

Valeria eHernández-Hernández

2014-06-01

Full Text Available Mechanical forces such as tension and compression act throughout growth and development of multicellular organisms. These forces not only affect the size and shape of the cells and tissues but are capable of modifying the expression of genes and the localization of molecular components within the cell, in the plasma membrane, and in the plant cell wall. The magnitude and direction of these physical forces change with cellular and tissue properties such as elasticity. Thus, mechanical forces and the mesoscopic fields that emerge from their local action constitute important sources of positional information. Moreover, physical and biochemical processes interact in non-linear ways during tissue and organ growth in plants and animals. In this review we discuss how such mechanical forces are generated, transmitted, and sensed in these two lineages of multicellular organisms to yield long-range positional information. In order to do so we first outline a potentially common basis for studying patterning and mechanosensing that relies on the structural principle of tensegrity, and discuss how tensegral structures might arise in plants and animals. We then provide some examples of morphogenesis in which mechanical forces appear to act as positional information during development, offering a possible explanation for ubiquitous processes, such as the formation of periodic structures. Such examples, we argue, can be interpreted in terms of tensegral phenomena. Finally, we discuss the hypothesis of mechanically isotropic points as a potentially generic mechanism for the localization and maintenance of stem-cell niches in multicellular organisms. This comparative approach aims to help uncovering generic mechanisms of morphogenesis and thus reach a better understanding of the evolution and development of multicellular phenotypes, focusing on the role of physical forces in these processes.

A study on the force balance of an unbalanced globe valve

International Nuclear Information System (INIS)

Yang, Sang Min; Cho, Taik Dong; Ko, Sung Ho; Lee, Ho Young

2007-01-01

A pneumatic control valve is a piping element that controls the volumetric flow rate and pressure of a fluid: it is necessary to analyze the characteristics of the forces with respect to the opening of the valve in order to evaluate its operating performance. The forces occurring during operation are: resisting force and actuator force, where the load resistance is mostly affected by the fluid pressure difference of the valve. In this study, a force balance equation derived from the equilibrium relationship between the resisting force and the actuator force of an unbalanced globe valve is proposed, and the force balance equations are used to model the dynamic equations of a pneumatic unbalanced globe valve installed in nuclear power plants. A CFD analysis is also carried out to evaluate the pressure distribution and forces acting on the top and bottom planes of the valve plug. The results of this analysis have been verified through experimentation. This study has shown that the fluid pressure difference between the inlet and outlet of the valve, measured from the force balance equation of an unbalanced valve, should actually be examined with the fluid-pressure difference between the top and bottom side of the valve plug

Yugoslavia: Act of 21 November 1984 on radiation protection and the safe use of nuclear energy

International Nuclear Information System (INIS)

1985-01-01

This Act which entered into force on 1 December 1984 repeals the 1976 Act on Protection against Ionizing Radiation and regulates most of the peaceful uses of nuclear energy and radiation protection in Yugoslavia. The Act lays down the licensing procedure for nuclear installations and covers safety-related questions in connection with standards, technical criteria etc. It also takes into account several areas regulated at international level, namely safeguards and physical protection of nuclear material. (NEA) [fr

Geometric Aspects of Force Controllability for a Swimming Model

International Nuclear Information System (INIS)

Khapalov, A. Y.

2008-01-01

We study controllability properties (swimming capabilities) of a mathematical model of an abstract object which 'swims' in the 2-D Stokes fluid. Our goal is to investigate how the geometric shape of this object affects the forces acting upon it. Such problems are of interest in biology and engineering applications dealing with propulsion systems in fluids

Dutch National Security Reform Under Review : Sufficient Checks and Balances in the Intelligence and Security Services Act 2017?

NARCIS (Netherlands)

Quirine Eijkman; Nico van Eijk; Robert van Schaik

2018-01-01

In May 2018, the new Dutch Intelligence and Security Services Act 2017 (Wet op de Inlichtingen- en veiligheidsdiensten, Wiv) will enter into force. It replaces the previous 2002 Act and incorporates many reforms to the information gathering powers of the two intelligence and security services as

Biomechanics of gecko locomotion: the patterns of reaction forces on inverted, vertical and horizontal substrates

International Nuclear Information System (INIS)

Wang, Zhouyi; Dai, Zhendong; Ji, Aihong; Xing, Qiang; Ren, Lei; Dai, Liming

2015-01-01

The excellent locomotion ability of geckos on various rough and/or inclined substrates has attracted scientists’ attention for centuries. However, the moving ability of gecko-mimicking robots on various inclined surfaces still lags far behind that of geckos, mainly because our understanding of how geckos govern their locomotion is still very poor. To reveal the fundamental mechanism of gecko locomotion and also to facilitate the design of gecko-mimicking robots, we have measured the reaction forces (RFs) acting on each individual foot of moving geckos on inverted, vertical and horizontal substrates (i.e. ceiling, wall and floor), have associated the RFs with locomotion behaviors by using high-speed camera, and have presented the relationships of the force components with patterns of reaction forces (PRFs). Geckos generate different PRF on ceiling, wall and floor, that is, the PRF is determined by the angles between the direction of gravity and the substrate on which geckos move. On the ceiling, geckos produce reversed shear forces acting on the front and hind feet, which pull away from the body in both lateral and fore-aft directions. They use a very large supporting angle from 21° to 24° to reduce the forces acting on their legs and feet. On the floor, geckos lift their bodies using a supporting angle from 76° to 78°, which not only decreases the RFs but also improves their locomotion ability. On the wall, geckos generate a reliable self-locking attachment by using a supporting angle of 14.8°, which is only about half of the critical angle of detachment. (paper)

THE RIGHTS GRANTED TO TRADE UNIONS UNDER THE COMPANIES ACT 71 OF 2008

Directory of Open Access Journals (Sweden)

Heidi C Schoeman

2013-08-01

Full Text Available With the entering into force of the Companies Act 71 of 2008 in 2011 a number of rights were granted to trade unions by the act. The Companies Act 71 of 2008 not only grants rights to registered trade unions, as is the case in labour law, but in some cases it grants rights to trade unions representing employees at the workplace. It is argued that rights afforded to trade unions by the act ought to be granted only to trade unions that are registered in terms of the Labour Relations Act 66 of 1995. In addition, it is also argued that the Companies Act 71 of 2008 ought in principle to differentiate between rights that are granted to registered trade unions representing employees at the workplace and rights that are granted to registered majority trade unions, or at the least to sufficiently representative trade unions.

Spatially Synchronous Extinction of Species under External Forcing

Science.gov (United States)

Amritkar, R. E.; Rangarajan, Govindan

2006-06-01

More than 99% of the species that ever existed on the surface of the Earth are now extinct and their extinction on a global scale has been a puzzle. One may think that a species under an external threat may survive in some isolated locations leading to the revival of the species. Using a general model we show that, under a common external forcing, the species with a quadratic saturation term first undergoes spatial synchronization and then extinction. The effect can be observed even when the external forcing acts only on some locations provided the dynamics contains a synchronizing term. Absence of the quadratic saturation term can help the species to avoid extinction.

Lateral force calibration in atomic force microscopy: A new lateral force calibration method and general guidelines for optimization

International Nuclear Information System (INIS)

Cannara, Rachel J.; Eglin, Michael; Carpick, Robert W.

2006-01-01

Proper force calibration is a critical step in atomic and lateral force microscopies (AFM/LFM). The recently published torsional Sader method [C. P. Green et al., Rev. Sci. Instrum. 75, 1988 (2004)] facilitates the calculation of torsional spring constants of rectangular AFM cantilevers by eliminating the need to obtain information or make assumptions regarding the cantilever's material properties and thickness, both of which are difficult to measure. Complete force calibration of the lateral signal in LFM requires measurement of the lateral signal deflection sensitivity as well. In this article, we introduce a complete lateral force calibration procedure that employs the torsional Sader method and does not require making contact between the tip and any sample. In this method, a colloidal sphere is attached to a 'test' cantilever of the same width, but different length and material as the 'target' cantilever of interest. The lateral signal sensitivity is calibrated by loading the colloidal sphere laterally against a vertical sidewall. The signal sensitivity for the target cantilever is then corrected for the tip length, total signal strength, and in-plane bending of the cantilevers. We discuss the advantages and disadvantages of this approach in comparison with the other established lateral force calibration techniques, and make a direct comparison with the 'wedge' calibration method. The methods agree to within 5%. The propagation of errors is explicitly considered for both methods and the sources of disagreement discussed. Finally, we show that the lateral signal sensitivity is substantially reduced when the laser spot is not centered on the detector

In-depth Study on Cylinder Wake Controlled by Lorentz Force

International Nuclear Information System (INIS)

Zhang Hui; Fan Bao-Chun; Chen Zhi-Hua

2011-01-01

The underlying mechanisms of the electromagnetic control of cylinder wake are investigated and discussed. The effects of Lorentz force are found to be composed of two parts, one is its direct action on the cylinder (the wall Lorentz force) and the other is applied to the fluid (called the field Lorentz force) near the cylinder surface. Our results show that the wall Lorentz force can generate thrust and reduce the drag; the field Lorentz force increases the drag. However, the cylinder drag is dominated by the wall Lorentz force. In addition, the field Lorentz force above the upper surface decreases the lift, while the upper wall Lorentz force increases it. The total lift is dominated by the upper wall Lorentz force. (fundamental areas of phenomenology(including applications))

Extended Analysis of the Casimir Force

Directory of Open Access Journals (Sweden)

Lehnert B.

2014-04-01

Full Text Available There are several arguments for the conventional form of the Zero Point Energy fre- quency spectrum to be put in doubt. It has thus to be revised in to that of a self-consistent system in statistical equilibrium where the total energy de nsity and the equivalent pres- sure become finite. An extended form of the Casimir force is th ereby proposed to be used as a tool for determining the local magnitude of the same pressure. This can be done in terms of measurements on the force between a pair po lished plane plates consisting of different metals, the plates having very small or zero air gaps. T his corre- sponds to the largest possible Casimir force. Even then, the re may arise problems with other adhering forces, possibly to be clarified in further experiments.

Adaptive Equilibrium Regulation: A Balancing Act in Two Timescales

Science.gov (United States)

Boker, Steven M.

2015-01-01

An equilibrium involves a balancing of forces. Just as one maintains upright posture in standing or walking, many self-regulatory and interpersonal behaviors can be framed as a balancing act between an ever changing environment and within-person processes. The emerging balance between person and environment, the equilibria, are dynamic and adaptive in response to development and learning. A distinction is made between equilibrium achieved solely due to a short timescale balancing of forces and a longer timescale preferred equilibrium which we define as a state towards which the system slowly adapts. Together, these are developed into a framework that this article calls Adaptive Equilibrium Regulation (ÆR), which separates a regulatory process into two timescales: a faster regulation that automatically balances forces and a slower timescale adaptation process that reconfigures the fast regulation so as to move the system towards its preferred equilibrium when an environmental force persists over the longer timescale. This way of thinking leads to novel models for the interplay between multiple timescales of behavior, learning, and development. PMID:27066197

Identification of the nonlinear excitation force acting on a bowed string using the dynamical responses at remote locations

International Nuclear Information System (INIS)

Debut, V.; Antunes, J.; Delaune, X.

2010-01-01

For achieving realistic numerical simulations of bowed string instruments, based on physical modeling, a good understanding of the actual friction interaction phenomena is of great importance. Most work published in the field including our own has assumed that bow/string frictional forces behave according to the classical Coulomb stick-slip model, with an empirical velocity-dependent sliding friction coefficient. Indeed, the basic self-excited string motions (such as the Helmholtz regime) are well captured using such friction model. However, recent work has shown that the tribological behavior of the bow/string rosin interface is rather complex, therefore the basic velocity-dependent Coulomb model may be an over-simplistic representation of the friction force. More specifically, it was suggested that a more accurate model of the interaction force can be achieved by coupling the system dynamical equations with a thermal model which encapsulates the complex interface phenomena. In spite of the interesting work performed by Askenfelt, a direct measurement of the actual dynamical friction forces without disturbing the string motion is quite difficult. Therefore, in this work we develop a modal-based identification technique making use of inverse methods and optimization techniques, which enables the identification of the interface force, as well as the string self-excited motion, from the dynamical reactions measured at the string end supports. The method gives convincing results using simulated data originated from nonlinear computations of a bowed string. Furthermore, in cases where the force identifications are very sensitive to errors in the transfer function modal parameters, we suggest a method to improve the modal frequencies used for the identifications. Preliminary experimental results obtained using a basic bowing device, by which the string is excited with the stick of the bow, are then presented. Our identifications, from the two dynamical string reactions

78 FR 20912 - Clean Water Act: Availability of List Decisions

Science.gov (United States)

2013-04-08

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9798-8] Clean Water Act: Availability of List Decisions.... SUMMARY: The Clean Water Act requires that States periodically submit, and EPA approve or disapprove... are not stringent enough to attain or maintain State water quality standards and for which total...

Identification of Motive Forces on the Whole Body System during Walking

Directory of Open Access Journals (Sweden)

Raghdan J. AlKhoury

2010-01-01

Full Text Available Motive forces by muscles are applied to different parts of the human body in a periodic fashion when walking at a uniform rate. In this study, the whole human body is modeled as a multidegree of freedom (MDOF system with seven degrees of freedom. In view of the changing contact conditions with the ground due to alternating feet movements, the system under study is considered piecewise time invariant for each half-period when one foot is in contact with the ground. Forces transmitted from the body to the ground while walking at a normal pace are experimentally measured and numerically simulated. Fourth-order Runge-Kutta method is employed to numerically simulate the forces acting on different masses of the body. An optimization problem is formulated with the squared difference between the measured and simulated forces transmitted to the ground as the objective function, and the motive forces on the body masses as the design variables to solve.

Employment: Labor Force Status (1983-2012)

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — Civilian labor force data consists of the number of employed persons, the number of unemployed persons, an unemployment rate and the total count of both employed and...

Atomic Energy Authority (Special Constables) Act 1976 of 10 June 1976

International Nuclear Information System (INIS)

1976-01-01

This Act, which came into force on 10th June 1976, extends the powers of the UKAEA's Special Constables (i.e. Police) so that they may be better able to safeguard fissile materials in nuclear installations and during transport. Under the Act the UKAEA's Special Constables are deemed to be Crown servants for the purposes of the Firearms Act 1968, Section 2, and it extends the kind of property in relation to which the UKAEA's Special Constables may exercise their powers when they are outside the premises within which they were appointed to act. It also extends the geographical limits within which the UKAEA's Special Constables may exercise their powers, so that their powers may now be exercised wherever they may go in order to safeguard fissile materials or to pursue persons believed to have removed or attempted to remove such materials unlawfully. (NEA) [fr

Nonlinear nonresonant forces by radio-frequency waves in plasmas

International Nuclear Information System (INIS)

Gao Zhe; Fisch, Nathaniel J.; Qin, Hong; Myra, J. R.

2007-01-01

Nonresonant forces by applied rf waves in plasmas are analyzed. Along the background dc magnetic field, the force arises from the gradient of the ponderomotive potential. Only when the dc magnetic field is straight, however, is this parallel force completely consistent with that from the single particle picture, where the ponderomotive force depends on the gradients of rf fields only. Across the dc magnetic field, besides the ponderomotive force from the particle picture, additional Reynolds stress and polarization stress contribute to the total force. For waves with frequency much lower than the cyclotron frequency, the perpendicular forces from the particle and fluid pictures can have opposite signs. In plasmas with a symmetry angle (e.g., toroidal systems), nonresonant forces cannot drive net flow or current in the flux surface, but the radial force may influence macroscopic behavior of plasma. Moreover, nonresonant forces may drive flow or current in linear plasmas or in a localized region of toroidal plasmas

75 FR 20351 - Clean Water Act Section 303(d): Availability of One Total Maximum Daily Load (TMDL) in Arkansas

Science.gov (United States)

2010-04-19

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9139-5] Clean Water Act Section 303(d): Availability of One...: Notice of availability. SUMMARY: This notice announces the availability of the administrative record file... in the State of Arkansas under Section 303(d) of the Clean Water Act (CWA). This TMDL was completed...

Performance evaluation on force control for ITER blanket installation

Energy Technology Data Exchange (ETDEWEB)

Aburadani, A., E-mail: aburadani.atsushi@jaea.go.jp [Japan Atomic Energy Agency, Mukouyama 801-1, Naka, Ibaraki 311-0193 (Japan); Takeda, N.; Shigematsu, S.; Murakami, S.; Tanigawa, H.; Kakudate, S. [Japan Atomic Energy Agency, Mukouyama 801-1, Naka, Ibaraki 311-0193 (Japan); Nakahira, M.; Hamilton, D.; Tesini, A. [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France)

2013-10-15

Highlights: ► It is crucial issues to avoid any jamming between the blanket modules and the keys. ► Force control for AC servo motor was developed to reduce excessive loads. ► This jam prevention force control method is directly measured and controlled by AC servo motor controllers. ► In the recent test, the module was passively positioned onto keys using the torque control method. -- Abstract: The most critical issue for the ITER blanket installation is to avoid any jamming between the blanket modules and the keys as a result of excessive loading during the module installation process. This is complicated by the limited clearance of 0.5 mm between the modules and the keys. To solve these technical issues, force control, such as controlling the torque for the AC servo motors, was developed to reduce excessive loads which may have an impact on the end-effector and to defer the forces acting on the groove of the blanket. This jam prevention force control method is directly measured and controlled by AC servo motor controllers. The AC servo motors are equipped to move the manipulator and end-effector during module installation.

Performance evaluation on force control for ITER blanket installation

International Nuclear Information System (INIS)

Aburadani, A.; Takeda, N.; Shigematsu, S.; Murakami, S.; Tanigawa, H.; Kakudate, S.; Nakahira, M.; Hamilton, D.; Tesini, A.

2013-01-01

Highlights: ► It is crucial issues to avoid any jamming between the blanket modules and the keys. ► Force control for AC servo motor was developed to reduce excessive loads. ► This jam prevention force control method is directly measured and controlled by AC servo motor controllers. ► In the recent test, the module was passively positioned onto keys using the torque control method. -- Abstract: The most critical issue for the ITER blanket installation is to avoid any jamming between the blanket modules and the keys as a result of excessive loading during the module installation process. This is complicated by the limited clearance of 0.5 mm between the modules and the keys. To solve these technical issues, force control, such as controlling the torque for the AC servo motors, was developed to reduce excessive loads which may have an impact on the end-effector and to defer the forces acting on the groove of the blanket. This jam prevention force control method is directly measured and controlled by AC servo motor controllers. The AC servo motors are equipped to move the manipulator and end-effector during module installation

TRIGA forced shutdowns analysis

International Nuclear Information System (INIS)

Negut, Gheorghe; Laslau, Florica

2008-01-01

The need for improving the operation leads us to use new methods and strategies. Probabilistic safety assessments and statistical analysis provide insights useful for our reactor operation. This paper is dedicated to analysis of the forced shutdowns during the first reactor operation period, between 1980 to 1989. A forced shutdown data base was designed using data on forced shutdowns collected from the reactor operation logbooks. In order to sort out the forced shutdowns the records have the following fields: - current number, date, equipment failed, failure type (M for mechanical, E for electrical, D for irradiation device, U for human factor failure; - scram mode, SE for external scram, failure of reactor cooling circuits and/or irradiation devices, SR for reactor scram, exceeding of reactor nuclear parameters, SB for reactor scram by control rod drop, SM for manual scram required by the abnormal reactor status; - scram cause, giving more information on the forced shutdown. This data base was processed using DBase III. The data processing techniques are presented. To sort out the data, one of the criteria was the number of scrams per year, failure type, scram mode, etc. There are presented yearly scrams, total operation time in hours, total unavailable time, median unavailable time period, reactor availability A. There are given the formulae used to calculate the reactor operational parameters. There are shown the scrams per year in the 1980 to 1989 period, the reactor operation time per year, the reactor shutdown time per year and the operating time versus down time per year. Total number of scrams in the covered period was 643 which caused a reactor down time of 4282.25 hours. In a table the scrams as sorted on the failure type is shown. Summarising, this study emphasized some problems and difficulties which occurred during the TRIGA reactor operation at Pitesti. One main difficulty in creating this data base was the unstandardized scram record mode. Some times

Ponderomotive force, magnetic fields and hydrodynamics of laser produced plasmas

International Nuclear Information System (INIS)

Bobin, J.-L.; Wee Woo; Degroot, J.-S.

1977-01-01

Nonlinear effects deeply change the structure of a laser driven plasma flow. For high intensities, the radiation pressure should be taken into account. It acts through a ponderomotive force proportional to the electron density and to the gradient of the mean electric field energy density of the incident wave. Static magnetic fields originate from a term in the ponderomotive force which includes radiation absorption and whose curl is non zero. The basic properties of the structure are determined analytically in the absence of thermal conductivity and magnetic fields: steep density gradient close to the cut-off density, shelf at lower densities. The conditions of a steady state regime are set up. The isothermal case is specially investigated. It is shown that the cavities which are created in a motionless plasma may disappear due to the onset of a flow. Regions in which electromagnetic forces arising from the static field compensate the ponderomotive force are determined. The subsequent effects on the flow itself are studied [fr

Some Consequences of Prompting Novice Physics Students to Construct Force Diagrams

Science.gov (United States)

Heckler, Andrew F.

2010-01-01

We conducted a series of experiments to investigate the extent to which prompting the construction of a force diagram affects student solutions to simple mechanics problems. A total of 891 university introductory physics students were given typical force and motion problems under one of the two conditions: when a force diagram was or was not…

Application of Taguchi method for cutting force optimization in rock

Indian Academy of Sciences (India)

In this paper, an optimization study was carried out for the cutting force (Fc) acting on circular diamond sawblades in rock sawing. The peripheral speed, traverse speed, cut depth and flow rate of cooling fluid were considered as operating variables and optimized by using Taguchi approach for the Fc. L16(44) orthogonal ...

Self-Evident Truths: Why We Can Stop Worrying and Love the Posse Comitatus Act

National Research Council Canada - National Science Library

Gentry, Chris R

2008-01-01

.... The author presents an analysis that outlines the evolution of legal theory and acts pertaining to the use of the military in domestic crises and past and current applications of military force in the United States...

Advocating for School Psychologists in Response to the APA's Proposed "Model Act for State Licensure of Psychologists"

Science.gov (United States)

Skalski, Anastasia Kalamaros

2009-01-01

On March 6, 2009, the APA Model Licensure Act Task Force released its second draft of the policy document known as the proposed "Model Act for State Licensure of Psychologists". This policy document serves as guidance to state legislatures for how they should set up their psychology licensing laws. The general expectations promoted in the model…

The State Surveillance over Nuclear Safety of Nuclear Facilities Act No. 28/1984

International Nuclear Information System (INIS)

1995-01-01

The Act lays down responsibilities of the Czechoslovak Atomic Energy Commission in the field of state surveillance over nuclear safety of nuclear facilities; determines the responsibilities of nuclear safety inspectors in their inspection activities; specifies duties of bodies and corporations responsible for nuclear safety of nuclear facilities; stipulates the obligation to set up emergency plans; and specifies penalties imposed on corporations and individuals for noncompliance with nuclear safety provisions. The Act entered into force on 4 April 1984. (J.B.)

Act No. 84 amending the decision of the Ministry of Communications on Transport of Dangerous Substances by Road

International Nuclear Information System (INIS)

1987-01-01

This Act amends Decision No. 610 of 1978 of the Ministry of Communications on the Transport of Dangerous Substances by Road, which also covers radioactive substances; the amendments in their respect set out in the Annexes are of a technical nature. The Act entered into force on 1 April 1987. (NEA) [fr

Influence of flow force on the flapper of a water hydraulic servovalve; Suiatsu servo ben no flapper ni sayosuru ryutairyoku no eikyo

Energy Technology Data Exchange (ETDEWEB)

Urata, E. [Kanagawa University, Kanagawa (Japan). Faculty of Engineering; Yamashina, C. [Ebara Research Co. Ltd., Kanagawa (Japan)

1997-06-25

In this paper flow force due to nozzle flow and its influence on the flapper-nozzle system for water hydraulic servovalves are discussed. The flow force acting on the flapper is estimated using the momentum theory, and expressed as a function of the nozzle pressure and flapper-nozzle gap. Analysis shows that the double nozzle flapper gives a quasilinear characteristic to the relationship between the force on the flapper, the flapper gap and the spool velocity. The numerical result based on the theory is used to estimate accuracy of the classical linear approximation. The flow force reduces the magnitude of the change of the nozzle back pressures which drive the spool of the water hydraulic valve, because the input moment acting on the armature is resisted by the moment due to the flow force. Experimental verification of the theory is also given. 7 refs., 10 figs., 1 tab.

[The geometry of the keel determines the behaviour of the tibial tray against torsional forces in total knee replacement].

Science.gov (United States)

García David, S; Cortijo Martínez, J A; Navarro Bermúdez, I; Maculé, F; Hinarejos, P; Puig-Verdié, L; Monllau, J C; Hernández Hermoso, J A

2014-01-01

The keel design of the tibial tray is essential for the transmission of the majority of the forces to the peripheral bone structures, which have better mechanical proprieties, thus reducing the risk of loosening. The aim of the present study was to compare the behaviour of different tibial tray designs submitted to torsional forces. Four different tibial components were modelled. The 3-D reconstruction was made using the Mimics software. The solid elements were generated by SolidWorks. The finite elements study was done by Unigraphics. A torsional force of 6 Nm. applied to the lateral aspects of each tibial tray was simulated. The GENUTECH® tibial tray, with peripheral trabecular bone support, showed a lower displacement and less transmitted tensions under torsional forces. The results suggest that a tibial tray with more peripheral support behaves mechanically better than the other studied designs. Copyright © 2013 SECOT. Published by Elsevier Espana. All rights reserved.

Generating a stationary infinite range tractor force via a multimode optical fibre

Science.gov (United States)

Ebongue, C. A.; Holzmann, D.; Ostermann, S.; Ritsch, H.

2017-06-01

Optical fibres confine and guide light almost unattenuated and thus convey light forces to polarizable nano-particles over very long distances. Radiation pressure forces arise from scattering of guided photons into free space while gradient forces are based on coherent scattering between different fibre modes or propagation directions. Interestingly, even scattering between co-propagating modes induces longitudinal forces as the transverse confinement of the light modes creates mode dependent longitudinal wave-vectors and photon momenta. We generalize a proven scattering matrix based approach to calculate single as well as inter-particle forces to include several forward and backward propagating modes. We show that an injection of the higher order mode only in a two mode fibre will induce a stationary tractor force against the injection direction, when the mode coupling to the lower order mode dominates against backscattering and free space losses. Generically this arises for non-absorbing particles at the centre of a waveguide. The model also gives improved predictions for inter-particle forces in evanescent nanofibre fields as experimentally observed recently. Surprisingly strong tractor forces can also act on whole optically bound arrays.

Optical force on diseased blood cells: Towards the optical sorting of biological matter

KAUST Repository

Gongora, J. S. Totero; Fratalocchi, Andrea

2015-01-01

By employing a series of massively parallel ab-initio simulations, we study how optical forces act on biological matter subject to morphological disease. As a representative case study, we here consider the case of Plasmodium falciparum on red blood

Environmental Monitoring, Water Quality - Total Maximum Daily Load (TMDL)

Data.gov (United States)

NSGIC Education | GIS Inventory — The Clean Water Act Section 303(d) establishes the Total Maximum Daily Load (TMDL) program. The purpose of the TMDL program is to identify sources of pollution and...

Force and torque of a string on a pulley

Science.gov (United States)

de Oliveira, Thiago R.; Lemos, Nivaldo A.

2018-04-01

Every university introductory physics course considers the problem of Atwood's machine taking into account the mass of the pulley. In the usual treatment, the tensions at the two ends of the string are offhandedly taken to act on the pulley and be responsible for its rotation. However, such a free-body diagram of the forces on the pulley is not a priori justified, inducing students to construct wrong hypotheses such as that the string transfers its tension to the pulley or that some symmetry is in operation. We reexamine this problem by integrating the contact forces between each element of the string and the pulley and show that although the pulley does behave as if the tensions were acting on its ends, this comes only as the final result of a detailed analysis. We also address the question of how much friction is needed to prevent the string from slipping over the pulley. Finally, we deal with the case in which the string is on the verge of sliding and show that this cannot happen unless certain conditions are met by the coefficient of static friction and the masses involved.

Optical pulling and pushing forces exerted on silicon nanospheres with strong coherent interaction between electric and magnetic resonances.

Science.gov (United States)

Liu, Hongfeng; Panmai, Mingcheng; Peng, Yuanyuan; Lan, Sheng

2017-05-29

We investigated theoretically and numerically the optical pulling and pushing forces acting on silicon (Si) nanospheres (NSs) with strong coherent interaction between electric and magnetic resonances. We examined the optical pulling and pushing forces exerted on Si NSs by two interfering waves and revealed the underlying physical mechanism from the viewpoint of electric- and magnetic-dipole manipulation. As compared with a polystyrene (PS) NS, it was found that the optical pulling force for a Si NS with the same size is enlarged by nearly two orders of magnitude. In addition to the optical pulling force appearing at the long-wavelength side of the magnetic dipole resonance, very large optical pushing force is observed at the magnetic quadrupole resonance. The correlation between the optical pulling/pushing force and the directional scattering characterized by the ratio of the forward to backward scattering was revealed. More interestingly, it was found that the high-order electric and magnetic resonances in large Si NSs play an important role in producing optical pulling force which can be generated by not only s-polarized wave but also p-polarized one. Our finding indicates that the strong coherent interaction between the electric and magnetic resonances existing in nanoparticles with large refractive indices can be exploited to manipulate the optical force acting on them and the correlation between the optical force and the directional scattering can be used as guidance. The engineering and manipulation of optical forces will find potential applications in the trapping, transport and sorting of nanoparticles.

Designing an experiment to measure cellular interaction forces

Science.gov (United States)

McAlinden, Niall; Glass, David G.; Millington, Owain R.; Wright, Amanda J.

2013-09-01

Optical trapping is a powerful tool in Life Science research and is becoming common place in many microscopy laboratories and facilities. The force applied by the laser beam on the trapped object can be accurately determined allowing any external forces acting on the trapped object to be deduced. We aim to design a series of experiments that use an optical trap to measure and quantify the interaction force between immune cells. In order to cause minimum perturbation to the sample we plan to directly trap T cells and remove the need to introduce exogenous beads to the sample. This poses a series of challenges and raises questions that need to be answered in order to design a set of effect end-point experiments. A typical cell is large compared to the beads normally trapped and highly non-uniform - can we reliably trap such objects and prevent them from rolling and re-orientating? In this paper we show how a spatial light modulator can produce a triple-spot trap, as opposed to a single-spot trap, giving complete control over the object's orientation and preventing it from rolling due, for example, to Brownian motion. To use an optical trap as a force transducer to measure an external force you must first have a reliably calibrated system. The optical trapping force is typically measured using either the theory of equipartition and observing the Brownian motion of the trapped object or using an escape force method, e.g. the viscous drag force method. In this paper we examine the relationship between force and displacement, as well as measuring the maximum displacement from equilibrium position before an object falls out of the trap, hence determining the conditions under which the different calibration methods should be applied.

STS-51 preparation: ACTS, ORFEUS, Discovery in VAB

Science.gov (United States)

1993-01-01

In NASA's building AM on Cape Canaveral Air Force Station, STS-51 mission specialist Carl Walz (right) and Deutsche Aerospace technician Gregor Dawidowitsch check over the scientific instruments mounted on the Shuttle Pallet Satellite (SPAS) carrier (38573); The Orbiting and Retrievable Far and Extreme Ultraviolet Spectrometer (ORFEUS) and SPAS is readied for hoisting into a test cell at the Vertical Processing Facility (VPF) (38574); Mating of the Advanced Communications Technology Satellite (ACTS) with the Transfer Orbit Stage (TOS) booster is under way in the Payload Hazardous Servicing Facility (PHSF) (38575); The mated ACTS and TOS are ready to be moved from the PHSF to the Vertical Processsing Facility (VPF) (38576); The orbiter Discovery is rolled into the Vehicle Assembly Building (VAB) for mating with the external tank and twin solid rocket boosters (38577-8).

Why the Community Reinvestment Act cannot be blamed for the subprime crisis

NARCIS (Netherlands)

Aalbers, M.B.

2009-01-01

It has become common practice—and in particular, but not exclusively, in conservative media—to blame the Community Reinvestment Act (CRA) of 1977 for the U.S. subprime mortgage and foreclosure crisis that triggered the global financial crisis. It is argued that the CRA forced lenders to give

Pushing nanoparticles with light — A femtonewton resolved measurement of optical scattering forces

Directory of Open Access Journals (Sweden)

C. Zensen

2016-05-01

Full Text Available Optomechanical manipulation of plasmonic nanoparticles is an area of current interest, both fundamental and applied. However, no experimental method is available to determine the forward-directed scattering force that dominates for incident light of a wavelength close to the plasmon resonance. Here, we demonstrate how the scattering force acting on a single gold nanoparticle in solution can be measured. An optically trapped 80 nm particle was repetitively pushed from the side with laser light resonant to the particle plasmon frequency. A lock-in analysis of the particle movement provides a measured value for the scattering force. We obtain a resolution of less than 3 femtonewtons which is an order of magnitude smaller than any measurement of switchable forces performed on nanoparticles in solution with single beam optical tweezers to date. We compared the results of the force measurement with Mie simulations of the optical scattering force on a gold nanoparticle and found good agreement between experiment and theory within a few fN.

Cellular dynamics of bovine aortic smooth muscle cells measured using MEMS force sensors

Science.gov (United States)

Tsukagoshi, Takuya; Nguyen, Thanh-Vinh; Hirayama Shoji, Kayoko; Takahashi, Hidetoshi; Matsumoto, Kiyoshi; Shimoyama, Isao

2018-04-01

Adhesive cells perceive the mechanical properties of the substrates to which they adhere, adjusting their cellular mechanical forces according to their biological characteristics. This mechanical interaction subsequently affects the growth, locomotion, and differentiation of the cell. However, little is known about the detailed mechanism that underlies this interaction between adherent cells and substrates because dynamically measuring mechanical phenomena is difficult. Here, we utilize microelectromechamical systems force sensors that can measure cellular traction forces with high temporal resolution (~2.5 µs) over long periods (~3 h). We found that the cellular dynamics reflected physical phenomena with time scales from milliseconds to hours, which contradicts the idea that cellular motion is slow. A single focal adhesion (FA) generates an average force of 7 nN, which disappears in ms via the action of trypsin-ethylenediaminetetraacetic acid. The force-changing rate obtained from our measurements suggests that the time required for an FA to decompose was nearly proportional to the force acting on the FA.

Stress energy of elastic globe in curved space and a slip-out force

International Nuclear Information System (INIS)

Sokolov, S.N.

1990-01-01

The energy of stresses in an elastic globe in the flat space and in curved space is expressed through scalar invariants of the curved space. This energy creates an additional force acting on elastic bodies in a gravitational field. 4 refs

Cylindrical Taylor states conserving total absolute magnetic helicity

Science.gov (United States)

Low, B. C.; Fang, F.

2014-09-01

The Taylor state of a three-dimensional (3D) magnetic field in an upright cylindrical domain V is derived from first principles as an extremum of the total magnetic energy subject to a conserved, total absolute helicity Habs. This new helicity [Low, Phys. Plasmas 18, 052901 (2011)] is distinct from the well known classical total helicity and relative total helicity in common use to describe wholly-contained and anchored fields, respectively. A given field B, tangential along the cylindrical side of V, may be represented as a unique linear superposition of two flux systems, an axially extended system along V and a strictly transverse system carrying information on field-circulation. This specialized Chandrasekhar-Kendall representation defines Habs and permits a neat formulation of the boundary-value problem (BVP) for the Taylor state as a constant-α force-free field, treating 3D wholly-contained and anchored fields on the same conceptual basis. In this formulation, the governing equation is a scalar integro-partial differential equation (PDE). A family of series solutions for an anchored field is presented as an illustration of this class of BVPs. Past treatments of the constant-α field in 3D cylindrical geometry are based on a scalar Helmholtz PDE as the governing equation, with issues of inconsistency in the published field solutions discussed over time in the journal literature. The constant-α force-free equation reduces to a scalar Helmholtz PDE only as special cases of the 3D integro-PDE derived here. In contrast, the constant-α force-free equation and the scalar Helmholtz PDE are absolutely equivalent in the spherical domain as discussed in Appendix. This theoretical study is motivated by the investigation of the Sun's corona but the results are also relevant to laboratory plasmas.

Assessing the industry using Porter's five forces.

Science.gov (United States)

2014-01-01

To develop a business and plan for the future, there is a need to assess the current situation. One way of doing this is to use Porter's five forces framework. This was the brainchild of Harvard Business School's Michael Porter and developed in 1979. Looking at the competitive intensity of an industry, the model assesses internal and external factors that act together to determine the direction of the business; taken together, this gives an indication of the attractiveness of the industry.

"A Completely New Approach" to Indigenous Cultural Heritage: Evaluating the Queensland Aboriginal Cultural Heritage Act

Directory of Open Access Journals (Sweden)

Mark E. O'Neill

2018-01-01

Full Text Available The Aboriginal Cultural Heritage Act 2003 challenged the hegemony that Western, archaeological methodologies has held over Indigenous cultural heritage in Australia. By choosing to relinquish state control and authority over cultural heritage in favour of the expertise of Indigenous people, the Act created a unique and innovative heritage policy. Over the 10 years the Act has been in force, it has seen a variety of approaches adopted as part of myriad projects. This has created a mature field of practice for investigation and analysis. This article examines and critiques the Act to determine its successes and weaknesses. In doing so, it offers opportunities for other policy-makers to consider as part of policy review.

Note: A rigid piezo motor with large output force and an effective method to reduce sliding friction force.

Science.gov (United States)

Guo, Ying; Hou, Yubin; Lu, Qingyou

2014-05-01

We present a completely practical TunaDrive piezo motor. It consists of a central piezo stack sandwiched by two arm piezo stacks and two leg piezo stacks, respectively, which is then sandwiched and spring-clamped by a pair of parallel polished sapphire rods. It works by alternatively fast expanding and contracting the arm/leg stacks while slowly expanding/contracting the central stack simultaneously. The key point is that sufficiently fast expanding and contracting a limb stack can make its two sliding friction forces well cancel, resulting in the total sliding friction force is piezo motor's high compactness, precision, and output force make it perfect in building a high-quality harsh-condition (vibration resistant) atomic resolution scanning probe microscope.

Pull-out test of stud bolts embedded in concrete under an in-plane force

International Nuclear Information System (INIS)

Inada, Y.; Saito, H.; Torita, H.; Takiguchi, K.; Ibe, Y.; Taira, T.

1995-01-01

There are many steel plates with stud bolts embedded in the R C walls of a nuclear reactor building to support equipment and piping. Under a earthquake, the steel plates are submitted to an out-of-plane force due to the inertia force acting upon equipment and piping. Furthermore, the walls are submitted to an in-plane force, and cracks may occur. A large number of experimental studies have been carried out on the pull-out strength of stud bolts embedded in concrete. Few studies have been performed to understand the strength of stud bolts embedded in concrete under an in-plane force and, further, not any one on the strength for concrete under in-plane force simultaneously to stud bolts under out-of-plane force. This paper describes a test performed to understand the pull-out strength determined by this interaction of in-plane and out-of-plane forces. (author). 5 refs., 9 figs., 5 tabs

Probing the nanoscale interaction forces and elastic properties of organic and inorganic materials using force-distance (F-D) spectroscopy

Science.gov (United States)

Vincent, Abhilash

Due to their therapeutic applications such as radical scavenging, MRI contrast imaging, Photoluminescence imaging, drug delivery, etc., nanoparticles (NPs) have a significant importance in bio-nanotechnology. The reason that prevents the utilizing NPs for drug delivery in medical field is mostly due to their biocompatibility issues (incompatibility can lead to toxicity and cell death). Changes in the surface conditions of NPs often lead to NP cytotoxicity. Investigating the role of NP surface properties (surface charges and surface chemistry) on their interactions with biomolecules (Cells, protein and DNA) could enhance the current understanding of NP cytotoxicity. Hence, it is highly beneficial to the nanotechnology community to bring more attention towards the enhancement of surface properties of NPs to make them more biocompatible and less toxic to biological systems. Surface functionalization of NPs using specific ligand biomolecules have shown to enhance the protein adsorption and cellular uptake through more favorable interaction pathways. Cerium oxide NPs (CNPs also known as nanoceria) are potential antioxidants in cell culture models and understanding the nature of interaction between cerium oxide NPs and biological proteins and cells are important due to their therapeutic application (especially in site specific drug delivery systems). The surface charges and surface chemistry of CNPs play a major role in protein adsorption and cellular uptake. Hence, by tuning the surface charges and by selecting proper functional molecules on the surface, CNPs exhibiting strong adhesion to biological materials can be prepared. By probing the nanoscale interaction forces acting between CNPs and protein molecules using Atomic Force Microscopy (AFM) based force-distance (F-D) spectroscopy, the mechanism of CNP-protein adsorption and CNP cellular uptake can be understood more quantitatively. The work presented in this dissertation is based on the application of AFM in

25 CFR 700.33 - Act (The Act).

Science.gov (United States)

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Act (The Act). 700.33 Section 700.33 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES General Policies and Instructions Definitions § 700.33 Act (The Act). (a) The Act. The Act is Pub. L. 93-531, (88 Stat...

Climate hypersensitivity to solar forcing?

Directory of Open Access Journals (Sweden)

W. Soon

2000-05-01

Full Text Available We compare the equilibrium climate responses of a quasi-dynamical energy balance model to radiative forcing by equivalent changes in CO2, solar total irradiance (Stot and solar UV (SUV. The response is largest in the SUV case, in which the imposed UV radiative forcing is preferentially absorbed in the layer above 250 mb, in contrast to the weak response from global-columnar radiative loading by increases in CO2 or Stot. The hypersensitive response of the climate system to solar UV forcing is caused by strongly coupled feedback involving vertical static stability, tropical thick cirrus ice clouds and stratospheric ozone. This mechanism offers a plausible explanation of the apparent hypersensitivity of climate to solar forcing, as suggested by analyses of recent climatic records. The model hypersensitivity strongly depends on climate parameters, especially cloud radiative properties, but is effective for arguably realistic values of these parameters. The proposed solar forcing mechanism should be further confirmed using other models (e.g., general circulation models that may better capture radiative and dynamical couplings of the troposphere and stratosphere.Key words: Meteorology and atmospheric dynamics (climatology · general or miscellaneous · Solar physics · astrophysics · and astronomy (ultraviolet emissions

Feasibility design of a floating airport and estimation of environmental forces on it; Futaishiki kuko no sekkei to kankyo gairyoku no suitei ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Inoue, Y.; Tabeta, S.; Takei, Y. [Yokohama National University, Yokohama (Japan). Faculty of Engineering

1996-12-31

A rough design was performed on a floating airport. On this floating structure, environmental external force was estimated, mooring design was carried out, and discussions was given on the position retaining performance important for airport functions and behavior of the floating structure. The discussion was given on cases that the airport is surrounded and not surrounded by floating breakwaters. A floating structure which becomes super-large in size requires considerations on force due to sea level gradient as a result of a tide. Deriving flow condition changes and force acting on the floating structure simultaneously by using numerical calculations makes it possible to estimate current force given with considerations on influence of the flow conditions created by installing the floating airport. Estimation was carried out by using a zone dividing method on wave drifting force acting upon the floating airport. As a result, it was found that installing floating and permeating type breakwaters can reduce the wave drifting force acting on the floating airport. The wave drifting force working on the floating airport can be reduced by installing the floating and permeating type breakwaters to lower levels than when no such breakwaters are installed. The airport may be moored with less number of fenders when the fenders of the same type are used. 18 refs., 10 figs., 5 tabs.

Force Modelling in Orthogonal Cutting Considering Flank Wear Effect

Science.gov (United States)

Rathod, Kanti Bhikhubhai; Lalwani, Devdas I.

2017-05-01

In the present work, an attempt has been made to provide a predictive cutting force model during orthogonal cutting by combining two different force models, that is, a force model for a perfectly sharp tool plus considering the effect of edge radius and a force model for a worn tool. The first force model is for a perfectly sharp tool that is based on Oxley's predictive machining theory for orthogonal cutting as the Oxley's model is for perfectly sharp tool, the effect of cutting edge radius (hone radius) is added and improve model is presented. The second force model is based on worn tool (flank wear) that was proposed by Waldorf. Further, the developed combined force model is also used to predict flank wear width using inverse approach. The performance of the developed combined total force model is compared with the previously published results for AISI 1045 and AISI 4142 materials and found reasonably good agreement.

Coulomb torque - a general theory for electrostatic forces in many-body systems

International Nuclear Information System (INIS)

Khachatourian, Armik V M; Wistrom, Anders O

2003-01-01

In static experiments that comprise three conducting spheres suspended by torsion wires and held at constant electric potential, a net angular displacement about their centres has been observed. We demonstrate that the observed rotation is consistent with Coulomb's law of electrical forces complemented by Gauss' surface integrals for electrical potential. Analysis demonstrates that electrostatic torque is the result of electrostatic forces acting on an asymmetric distribution of charges residing on the surfaces of the spheres. The asymptotic value for electrostatic torque is proportional to the inverse of the fourth power of separation distance with the rotation direction, up or down taken perpendicular to a plane passing through sphere centres, given explicitly by the equation for torque. The identification of electrostatic torque prompts further analysis of models of matter at all size scales where electrostatic forces are the dominant operative force

Coulomb torque - a general theory for electrostatic forces in many-body systems

CERN Document Server

Khachaturian, A V M

2003-01-01

In static experiments that comprise three conducting spheres suspended by torsion wires and held at constant electric potential, a net angular displacement about their centres has been observed. We demonstrate that the observed rotation is consistent with Coulomb's law of electrical forces complemented by Gauss' surface integrals for electrical potential. Analysis demonstrates that electrostatic torque is the result of electrostatic forces acting on an asymmetric distribution of charges residing on the surfaces of the spheres. The asymptotic value for electrostatic torque is proportional to the inverse of the fourth power of separation distance with the rotation direction, up or down taken perpendicular to a plane passing through sphere centres, given explicitly by the equation for torque. The identification of electrostatic torque prompts further analysis of models of matter at all size scales where electrostatic forces are the dominant operative force.

Optical properties of gold films and the Casimir force

International Nuclear Information System (INIS)

Svetovoy, V. B.; Zwol, P. J. van; Palasantzas, G.; De Hosson, J. Th. M.

2008-01-01

Precise optical properties of metals are very important for accurate prediction of the Casimir force acting between two metallic plates. Therefore we measured ellipsometrically the optical responses of Au films in a wide range of wavelengths from 0.14 to 33 μm. The films at various thicknesses were deposited at different conditions on silicon or mica substrates. Considerable variation of the frequency dependent dielectric function from sample to sample was found. Detailed analysis of the dielectric functions was performed to check the Kramers-Kronig consistency, and extract the Drude parameters of the films. It was found that the plasma frequency varies in the range from 6.8 to 8.4 eV. It is suggested that this variation is related with the film density. X-ray reflectivity measurements support qualitatively this conclusion. The Casimir force is evaluated for the dielectric functions corresponding to our samples, and for that typically used in the precise prediction of the force. The force for our films was found to be 5%-14% smaller at a distance of 100 nm between the plates. Noise in the optical data is responsible for the force variation within 1%. It is concluded that prediction of the Casimir force between metals with a precision better than 10% must be based on the material optical response measured from visible to mid-infrared range

New Danish Company Act on Shareholders' Agreements

DEFF Research Database (Denmark)

Werlauff, Erik

2011-01-01

) organizational rights, (2) financial rights, and (3) rights of disposal, or in plainer words, the corporate (1) power, (2) money, and (3) exit. If a shareholders’ agreement is thoroughly kept and respected by all parties, both in the way they vote at general assemblies and in the way they act when wishing....... The substantial elements in many agreements are clauses on (1) voting for board candidates, (2) voting for dividends of certain proportions, and (3) first refusal rights, respectively, call options for shares in the company. Such clauses are at the very roots of corporate law, dealing with the shareholders’ (1......Section 82 of the Danish Company Act, in force from 1 March 2010, provides that ‘Shareholders’ agreements are neither binding on the company nor on decisions taken by the general assembly’. This has far-reaching consequences for shareholders’ agreements, also for already existing agreements...

Medical Total Force Management

Science.gov (United States)

2014-05-01

Facilities (MTFs). For specialties that are common in civilian labor markets , civilian providers generally cost less than military providers. While the...produced in Military Treatment Facilities (MTFs). For specialties that are common in civilian labor markets , civilian providers generally cost less...Attracting Fully Trained Medical Personnel,” CRM D0013237.A2 (Alexandria, VA: CNA Corporation, 2006). 66

Calculation of the TileCal magnetic forces using 3D Tosca model

International Nuclear Information System (INIS)

Morozov, N.A.; Samsonov, E.V.; Vorozhtsov, S.B.; Nessi, M.

1998-01-01

The purpose of the given paper is to contribute to the new summary (taking into account the latest information) of magnetic forces, acting on various parts of the TileCal of the ATLAS detector (LHC, CERN). To get an impression of the field distribution in the vicinity of the objects under consideration of existing 3D Tosca field model of the detector was used. The detailed distribution of forces along the border of various parts of the system, derived here, is valuable for understanding the mechanics of system performance

[Hunger strike and forced feeding: a historical look at medical practices].

Science.gov (United States)

Rieder, Jean-Pierre; Huber-Giseke, Tina; Getaz, Laurent; Kramer-Gauchat, Marie-Claire; Nyffenegger, Laurent; Gaspoz, Jean-Michel; Wolff, Hans

2010-12-01

Hunger strike is not a disease but a common situation in prisons. This article takes a historical look at medical practices in connection with the forced feeding of hunger strikers. We now know the fate of the strikers who were subjected to forced feeding. Depending on the context and the political situation in the country, the fate of these people, mostly political prisoners, is described as humiliating and abominable frequently ending in death or irreparable consequences. Particularly difficult for health professionals, this act raises clinical, ethical and legal questions and refers to the fundamental principles of medicine.

Ideal quantum gas in an expanding cavity: nature of nonadiabatic force.

Science.gov (United States)

Nakamura, K; Avazbaev, S K; Sobirov, Z A; Matrasulov, D U; Monnai, T

2011-04-01

We consider a quantum gas of noninteracting particles confined in the expanding cavity and investigate the nature of the nonadiabatic force which is generated from the gas and acts on the cavity wall. First, with use of the time-dependent canonical transformation, which transforms the expanding cavity to the nonexpanding one, we can define the force operator. Second, applying the perturbative theory, which works when the cavity wall begins to move at time origin, we find that the nonadiabatic force is quadratic in the wall velocity and thereby does not break the time-reversal symmetry, in contrast with general belief. Finally, using an assembly of the transitionless quantum states, we obtain the nonadiabatic force exactly. The exact result justifies the validity of both the definition of the force operator and the issue of the perturbative theory. The mysterious mechanism of nonadiabatic transition with the use of transitionless quantum states is also explained. The study is done for both cases of the hard- and soft-wall confinement with the time-dependent confining length. ©2011 American Physical Society

Force prediction in permanent magnet flat linear motors (abstract)

International Nuclear Information System (INIS)

Eastham, J.F.; Akmese, R.

1991-01-01

The advent of neodymium iron boron rare-earth permanent magnet material has afforded the opportunity to construct linear machines of high force to weight ratio. The paper describes the design and construction of an axial flux machine and rotating drum test rig. The machine occupies an arc of 45 degree on a drum 1.22 m in diameter. The excitation is provided by blocks of NdFeB material which are skewed in order to minimize the force variations due to slotting. The stator carries a three-phase short-chorded double-layer winding of four poles. The machine is supplied by a PWM inverter the fundamental component of which is phase locked to the rotor position so that a ''dc brushless'' drive system is produced. Electromagnetic forces including ripple forces are measured at supply frequencies up to 100 Hz. They are compared with finite-element analysis which calculates the force variation over the time period. The paper then considers some of the causes of ripple torque. In particular, the force production due solely to the permanent magnet excitation is considered. This has two important components each acting along the line of motion of the machine, one is due to slotting and the other is due to the finite length of the primary. In the practical machine the excitation poles are skewed to minimize the slotting force and the effectiveness of this is confirmed by both results from the experiments and the finite-element analysis. The end effect force is shown to have a space period of twice that of the excitation. The amplitude of this force and its period are again confirmed by practical results

DETERMINATION THE PERMISSIBLE FORCES IN ASSESSING THE LIFT RESISTANT FACTOR OF FREIGHT CARS IN TRAINS

Directory of Open Access Journals (Sweden)

A. O. Shvets

2016-02-01

Full Text Available Purpose. In the analytical research are considered: 1 relationships between the longitudinal force acting on the car in the train; 2 lateral and vertical forces of interaction in the contact zone «wheel – rail»; 3 dynamic indicators of cars with the magnitude of the car lift resistance factor; 4 obtaining of the dependencies between them. Methodology. The study was conducted by an analytical method assessing the sustainability of the freight car when driving at different speeds on the straight and curved track sections. Findings. In the process of studying the motion of the train, in the investigation of transport events, as well as during the training on the simulator operator, to assess the actions of the driver, the values of the longitudinal forces in the inter car connections are used. To calculate the longitudinal compressive forces, acting on the car, in which car lift resistance factor will be equal to the allowable value (critical force. To assess the impact on the value of the longitudinal force speed, coefficients of the vertical and horizontal dynamics, as well as the wind load on the side surface of the car body are the results of calculations of motion of the empty gondola car, model № 12-532 curve radius of 250 m with a rise of 150 mm and a transverse run of body of car frame relative to the track axis of the guide section 50 mm. Originality. In this study, the technique of determining the longitudinal compressive force was shown, that is somewhat different from the standard. So, as well as assessing the impact on it the speed of rolling coefficients of vertical and horizontal dynamics and wind load on the side surface of the car body. Practical value. The authors developed proposals on the enhancement of existing methods for determining the value of the longitudinal compressive forces acting on the car in which the safety value of the car lift resistance factor will be equal to the allowable value. It will evaluate the

The Danish patient safety experience: the Act on Patient Safety in the Danish Health care system

DEFF Research Database (Denmark)

Lundgaard, Mette; Rabøl, Louise; Jensen, Elisabeth Agnete Brøgger

2005-01-01

This paper describes the process that lead to the passing of the Act for Patient Safety in the Danisk health care sytem, the contents of the act and how the act is used in the Danish health care system. The act obligates frontline health care personnel to report adverse events, hospital owners...... to act on the reports and the National Board of Health to commuicate the learning nationally. The act protects health care providers from sanctions as a result of reporting. In January 2004, the Act on Patient Safety in the Danish health care system was put into force. In the first twelve months 5740...... adverse events were reported. the reports were analyzed locally (hospital and region), anonymized ad then sent to the National Board af Health. The Act on Patient Safety has driven the work with patient safety forward but there is room for improvement. Continuous and improved feedback from all parts...

Electronic zero-point fluctuation forces inside circuit components

Science.gov (United States)

Leonhardt, Ulf

2018-01-01

One of the most intriguing manifestations of quantum zero-point fluctuations are the van der Waals and Casimir forces, often associated with vacuum fluctuations of the electromagnetic field. We study generalized fluctuation potentials acting on internal degrees of freedom of components in electrical circuits. These electronic Casimir-like potentials are induced by the zero-point current fluctuations of any general conductive circuit. For realistic examples of an electromechanical capacitor and a superconducting qubit, our results reveal the possibility of tunable forces between the capacitor plates, or the level shifts of the qubit, respectively. Our analysis suggests an alternative route toward the exploration of Casimir-like fluctuation potentials, namely, by characterizing and measuring them as a function of parameters of the environment. These tunable potentials may be useful for future nanoelectromechanical and quantum technologies. PMID:29719863

Electronic zero-point fluctuation forces inside circuit components.

Science.gov (United States)

Shahmoon, Ephraim; Leonhardt, Ulf

2018-04-01

One of the most intriguing manifestations of quantum zero-point fluctuations are the van der Waals and Casimir forces, often associated with vacuum fluctuations of the electromagnetic field. We study generalized fluctuation potentials acting on internal degrees of freedom of components in electrical circuits. These electronic Casimir-like potentials are induced by the zero-point current fluctuations of any general conductive circuit. For realistic examples of an electromechanical capacitor and a superconducting qubit, our results reveal the possibility of tunable forces between the capacitor plates, or the level shifts of the qubit, respectively. Our analysis suggests an alternative route toward the exploration of Casimir-like fluctuation potentials, namely, by characterizing and measuring them as a function of parameters of the environment. These tunable potentials may be useful for future nanoelectromechanical and quantum technologies.

Semiclassical force for electroweak baryogenesis three-dimensional derivation

CERN Document Server

Kainulainen, K; Schmidt, M G; Weinstock, S; Kainulainen, Kimmo; Prokopec, Tomislav; Schmidt, Michael G.; Weinstock, Steffen

2002-01-01

We derive a semiclassical transport equation for fermions propagating in the presence of a CP-violating planar bubble wall at a first order electroweak phase transition. Starting from the Kadanoff-Baym (KB) equation for the two-point (Wightman) function we perform an expansion in gradients, or equivalently in the Planck constant h-bar. We show that to first order in h-bar the KB equations have a spectral solution, which allows for an on-shell description of the plasma excitations. The CP-violating force acting on these excitations is found to be enhanced by a boost factor in comparison with the 1+1-dimensional case studied in a former paper. We find that an identical semiclassical force can be obtained by the WKB method. Applications to the MSSM are also mentioned.

Approximate Method of Calculating Forces on Rudder During Ship Sailing on a Shipping Route

Directory of Open Access Journals (Sweden)

K. Zelazny

2014-09-01

Full Text Available Service speed of a ship in real weather conditions is a basic design parameter. Forecasting of this speed at preliminary design stage is made difficult by the lack of simple but at the same accurate models of forces acting upon a ship sailing on a preset shipping route. The article presents a model for calculating forces and moment on plane rudder, useful for forecasting of ship service speed at preliminary stages of ship design.

Total shoulder replacement in rheumatoid arthritis

DEFF Research Database (Denmark)

Sneppen, O; Fruensgaard, S; Johannsen, Hans Viggo

1996-01-01

A prospective study of 62 Neer mark II total shoulder arthroplasties performed during the period from 1981 to 1990 on 51 patients with rheumatoid arthritis was undertaken to evaluate factors associated with component loosening and proximal humeral migration. Thirty-two (51%) showed proximal......, range of movement, abduction force, or function. The risk of clinical asymptomatic loosening is a relatively late complication that is eventually followed by pronounced bone destruction related to the loose component. Long-term radiographic control of total shoulders with rheumatoid arthritis...... is recommended. Hemiarthroplasty with a cemented humeral prosthesis may be a better treatment in the end stage of rheumatoid arthritis of the shoulder....

One Team, One Fight, One Future, Total Army Integration

National Research Council Canada - National Science Library

1998-01-01

...; and, most important, our vision for maintaining a trained and ready force. As the ideas in One Team, One Fight, One Future unfold, you will find the key themes of Total Army integration emerging again and again...

Bilateral ground reaction forces and joint moments for lateral sidestepping and crossover stepping tasks

Science.gov (United States)

Kuntze, Gregor; Sellers, William I.; Mansfield, Neil

2009-01-01

Racquet sports have high levels of joint injuries suggesting the joint loads during play may be excessive. Sports such as badminton employ lateral sidestepping (SS) and crossover stepping (XS) movements which so far have not been described in terms of biomechanics. This study examined bilateral ground reaction forces and three dimensional joint kinetics for both these gaits in order to determine the demands of the movements on the leading and trailing limb and predict the contribution of these movements to the occurrence of overuse injury of the lower limbs. A force platform and motion-analysis system were used to record ground reaction forces and track marker trajectories of 9 experienced male badminton players performing lateral SS, XS and forward running tasks at a controlled speed of 3 m·s-1 using their normal technique. Ground reaction force and kinetic data for the hip, knee and ankle were analyzed, averaged across the group and the biomechanical variables compared. In all cases the ground reaction forces and joint moments were less than those experienced during moderate running suggesting that in normal play SS and XS gaits do not lead to high forces that could contribute to increased injury risk. Ground reaction forces during SS and XS do not appear to contribute to the development of overuse injury. The distinct roles of the leading and trailing limb, acting as a generator of vertical force and shock absorber respectively, during the SS and XS may however contribute to the development of muscular imbalances which may ultimately contribute to the development of overuse injury. However it is still possible that faulty use of these gaits might lead to high loads and this should be the subject of future work. Key pointsGround reaction forces and joint moments during lateral stepping are smaller in magnitude than those experienced during moderate running.Force exposure in SS and XS gaits in normal play does not appear to contribute to the development of

Maximal loads acting on legs of powered roof support unit in longwalls with bumping hazards

Institute of Scientific and Technical Information of China (English)

StanislawSzweda

2001-01-01

In the article the results of measurements of the resultant force in the legs of a powered roof support unit, caused by a dynamic interaction bf the rock mass, are discussed. The measurements have been taken in the Iongwalls mined with a roof fall, characterized by the highest degree of bumping hazard. It has been stated that the maximal force in the legs Fro, recorded during a dynamic interaction of the rock mass, is proportional to the initial static force in the legs Fst.p Therefore a need for a careful selection of the initial load of the powered roof support, according to the local mining and geological conditions, results from such a statement. Setting the legs with the supporting load exceeding the indispensable value for keeping the direct roof solids in balance, deteriorating the operational parameters of a Iongwall system also has a disadvantageous influence on the value of the force in the legs and the rate of its increase, caused by a dynamic interaction of the rock mass. A correct selection of the initial load causes a decrease in the intensity of a dynamic interaction of the rock mass on powered roof supports, which also has an advanta igeous influence on their life, Simultaneously with the measurements of the resultant force in the legs, the vertical acceleration of the canopy was also recorded. It has enabled to prove that the external dynamic forces may act on the unit both from the roof as well as from the floor. The changes of the force in the legs caused by dynamic phenomena intrinsically created in the roof and changes of the force in the legs caused by blasting explosives in the roof of the working, have been analyzed separately. It has been stated that an increase in the loads of legs, caused by intrinsic phenomena is significantly higher than a force increase in the legs caused by blasting. It means that powered roof supports, to be operated in the workings, where the bumping hazard occurs, will also transmit the loads acting on a unit

Act of 18 March 1983 on Nuclear Third Party Liability (LRCN)

International Nuclear Information System (INIS)

1983-01-01

This new Act on nuclear third party liability maintains the two essential principles established by the law in force, namely those of causation and the channelling of liability on to the operator of a nuclear installation. On the other hand, the Act waives the principle of third party liability limited in amount and provides that the person liable must commit himself for an unlimited amount. Such liability is covered as follows: by private insurance up to 300 million francs; by the Confederation up to one thousand million francs over and above the amount covered by private insurance; by all the assets of the person liable. (NEA) [fr

Act of 25 February 1976 amending amounts and limits of the Civil Law

International Nuclear Information System (INIS)

1976-01-01

The Federal Act of 29 April 1964 on nuclear third party liability was modified by Section XXXIII of the Federal Act of 25 February 1976 amending amounts and limits fixed by the Civil Law. This modification came into force on 1 April 1976. For operators of nuclear installations and carriers the ceiling is now 500 million Austrian schillings. For radioisotope holders, the maximum amount depends on the radioactivity and the radiotoxicity of the isotope involved. The present ceiling ranges from 1.2 to 18 million schillings. (NEA) [fr

Effect of the repulsive force in the HTSC-permanent magnet hybrid bearing system

International Nuclear Information System (INIS)

Ohashi, S.; Kobayashi, S.

2009-01-01

Magnetic levitation using the pinning force of the YBaCuO high-T c bulk superconductor (HTSC) materials has an advantage to achieve stable levitation without control. To increase levitation force, the HTSC-permanent magnet hybrid magnetic bearing system is introduced. A circular shaped three phase Nd-Fe-B permanent magnet is installed on the rotor, and HTSC bulk superconductor is set on the stator. The additional permanent magnet is installed under the HTSC. Repulsive force of the permanent magnet is used for levitation, and pinning force between the HTSC and permanent magnet is used for guidance force of the bearing. In this system, relationship between permanent magnet and the HTSC is important. When repulsive force of the permanent magnet is large, pinning force of superconductor is used to keep the rotor position. As a result, stability for the lateral direction is decreased with hybrid system. For levitation force, effect of the hybrid system is not observed with column HTSC. Compared with the ring HTSC results, the following thing is considered. Because there is no space that flux of one permanent magnet acts on the other one with the column HTSC configuration, interaction between two permanent magnets becomes small.

Quantum limited force measurement in a cavityless optomechanical system

International Nuclear Information System (INIS)

Fermani, Rachele; Mancini, Stefano; Tombesi, Paolo

2004-01-01

We study the possibility of revealing a weak coherent force by using a pendular mirror as a probe, and coupling this to a radiation field, which acts as the meter, in a cavityless configuration. We determine the sensitivity of such a scheme and show that the use of an entangled meter state greatly improves the ultimate detection limit. We also compare this scheme with that involving an optical cavity

Slovak Republic Act No. 124/2006 Coll. of 2 February 2006 on safety and health at work and amending some laws

International Nuclear Information System (INIS)

2006-01-01

This Act establishes the general principles of prevention and basic conditions for ensuring safety and health at work and to eliminate the risk factors and conditioning the occurrence of occupational accidents, occupational diseases and other health damage. This Act came into force on July 1, 2006.

Universal spin-momentum locked optical forces

Energy Technology Data Exchange (ETDEWEB)

Kalhor, Farid [Department of Electrical and Computer Engineering, University of Alberta, Edmonton, Alberta T6G 1H9 (Canada); Thundat, Thomas [Department of Chemical and Materials Engineering, University of Alberta, Edmonton, Alberta T6G 1H9 (Canada); Jacob, Zubin, E-mail: zjacob@purdue.edu [Department of Electrical and Computer Engineering, University of Alberta, Edmonton, Alberta T6G 1H9 (Canada); Birck Nanotechnology Center, Department of Electrical and Computer Engineering, Purdue University, West Lafayette, Indiana 47906 (United States)

2016-02-08

Evanescent electromagnetic waves possess spin-momentum locking, where the direction of propagation (momentum) is locked to the inherent polarization of the wave (transverse spin). We study the optical forces arising from this universal phenomenon and show that the fundamental origin of recently reported non-trivial optical chiral forces is spin-momentum locking. For evanescent waves, we show that the direction of energy flow, the direction of decay, and the direction of spin follow a right hand rule for three different cases of total internal reflection, surface plasmon polaritons, and HE{sub 11} mode of an optical fiber. Furthermore, we explain how the recently reported phenomena of lateral optical force on chiral and achiral particles are caused by the transverse spin of the evanescent field and the spin-momentum locking phenomenon. Finally, we propose an experiment to identify the unique lateral forces arising from the transverse spin in the optical fiber and point to fundamental differences of the spin density from the well-known orbital angular momentum of light. Our work presents a unified view on spin-momentum locking and how it affects optical forces on chiral and achiral particles.

The Total Force: Cultural Considerations for the Future of the Total Force Integration

Science.gov (United States)

2017-03-31

address TFI as an organizational process or structure problem in which people, qualifications, and equipment, are objects that can be manipulated in...Merger and Cultural Change for Better Outcomes: The First Five Years of the New York State Office of Children and Family Services.” Child Welfare Vol...will take on the culture of the commander, [and therefore the commander must] make doing the right things easy and wrong [or] stupid things hard.”19

Adaptive increase in force variance during fatigue in tasks with low redundancy.

Science.gov (United States)

Singh, Tarkeshwar; S K M, Varadhan; Zatsiorsky, Vladimir M; Latash, Mark L

2010-11-26

We tested a hypothesis that fatigue of an element (a finger) leads to an adaptive neural strategy that involves an increase in force variability in the other finger(s) and an increase in co-variation of commands to fingers to keep total force variability relatively unchanged. We tested this hypothesis using a system with small redundancy (two fingers) and a marginally redundant system (with an additional constraint related to the total moment of force produced by the fingers, unstable condition). The subjects performed isometric accurate rhythmic force production tasks by the index (I) finger and two fingers (I and middle, M) pressing together before and after a fatiguing exercise by the I finger. Fatigue led to a large increase in force variance in the I-finger task and a smaller increase in the IM-task. We quantified two components of variance in the space of hypothetical commands to fingers, finger modes. Under both stable and unstable conditions, there was a large increase in the variance component that did not affect total force and a much smaller increase in the component that did. This resulted in an increase in an index of the force-stabilizing synergy. These results indicate that marginal redundancy is sufficient to allow the central nervous system to use adaptive increase in variability to shield important variables from effects of fatigue. We offer an interpretation of these results based on a recent development of the equilibrium-point hypothesis known as the referent configuration hypothesis. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Active electromagnetic invisibility cloaking and radiation force cancellation

Science.gov (United States)

Mitri, F. G.

2018-03-01

This investigation shows that an active emitting electromagnetic (EM) Dirichlet source (i.e., with axial polarization of the electric field) in a homogeneous non-dissipative/non-absorptive medium placed near a perfectly conducting boundary can render total invisibility (i.e. zero extinction cross-section or efficiency) in addition to a radiation force cancellation on its surface. Based upon the Poynting theorem, the mathematical expression for the extinction, radiation and amplification cross-sections (or efficiencies) are derived using the partial-wave series expansion method in cylindrical coordinates. Moreover, the analysis is extended to compute the self-induced EM radiation force on the active source, resulting from the waves reflected by the boundary. The numerical results predict the generation of a zero extinction efficiency, achieving total invisibility, in addition to a radiation force cancellation which depend on the source size, the distance from the boundary and the associated EM mode order of the active source. Furthermore, an attractive EM pushing force on the active source directed toward the boundary or a repulsive pulling one pointing away from it can arise accordingly. The numerical predictions and computational results find potential applications in the design and development of EM cloaking devices, invisibility and stealth technologies.

Scalable force directed graph layout algorithms using fast multipole methods

KAUST Repository

Yunis, Enas Abdulrahman

2012-06-01

We present an extension to ExaFMM, a Fast Multipole Method library, as a generalized approach for fast and scalable execution of the Force-Directed Graph Layout algorithm. The Force-Directed Graph Layout algorithm is a physics-based approach to graph layout that treats the vertices V as repelling charged particles with the edges E connecting them acting as springs. Traditionally, the amount of work required in applying the Force-Directed Graph Layout algorithm is O(|V|2 + |E|) using direct calculations and O(|V| log |V| + |E|) using truncation, filtering, and/or multi-level techniques. Correct application of the Fast Multipole Method allows us to maintain a lower complexity of O(|V| + |E|) while regaining most of the precision lost in other techniques. Solving layout problems for truly large graphs with millions of vertices still requires a scalable algorithm and implementation. We have been able to leverage the scalability and architectural adaptability of the ExaFMM library to create a Force-Directed Graph Layout implementation that runs efficiently on distributed multicore and multi-GPU architectures. © 2012 IEEE.

The resistible force

International Nuclear Information System (INIS)

Baeschlin, D.L.

1980-01-01

Many people of today have an oppositional attitude towards the continual loss of sense of existence which manifests itself in 'the great refusal'. They also behave in an anti-authoritarian manner towards their first father Marx. They realize that it is ourselves who have to search and find. The protest groups of the most different origin have come into being as 'the sand in the wheels' of a seemingly irresistable force. They have formed themselves beyond the 'Left' and the 'Right'. Nuclear energy is the instrument which acts as a gear for their opposition, which establishes it and which provides the basis for their self-concept. It is the symbol where the conflict between living standard and living quality breaks open. In essential, however, the protest is growing towards supporting an effective administration of all goods of our world. (orig./HP) [de

Some additional results on the directional relationships between forces and accelerations in special relativity

International Nuclear Information System (INIS)

Gonzalez-Diaz, P.F.

1979-01-01

Some directional relationships between forces and accelerations in special relativity have been studied by considering the most general case of a body having x, y and z components of velocity, which is acted upon by a force with nonzero components. The behaviour of asub(y)/asub(x) and asub(y)/asub(z) vs. velocity for different force component ratios is studied in the general situation in which vsub(x) is unequal to vsub(y) is unequal to vsub(z). It is shown that one or two, suddenly varying, negative acceleration components can result for the body at sufficiently high velocities, and an explanation is given. (author)

Some additional results on the directional relationships between forces and accelerations in special relativity

International Nuclear Information System (INIS)

Gonzales-Diaz, P.F.

1979-01-01

Some directional relationships between forces and accelerations in special relativity have been studied by considering the most general case of a body having x, y and z components of velocity, which is acted upon by a force with nonzero components. The behaviour of a sub(y)/ a sub(x) and a sub(y)/ a sub(z) vs. velocity for different force component ratios is studied in the general situation in which vsub(x) different from Vsub(y)different from vsub(z). It is shown that one or two, suddently varying, negative acceleration components can result for the body at sufficiently high velocities, and an explanation is given

Levitation force on a permanent magnet over a superconducting plane: Modified critical-state model

International Nuclear Information System (INIS)

Yang, Z.J.

1997-01-01

The authors consider a model system of a permanent magnet above a semi-infinite superconductor. They introduce a modified critical-state model, and carry out derivations of the levitation force acting on the magnet. A key feature of the modification allows the current density to be less than the critical value. The theoretical results show an exponential relationship between the force and the distance. Analytical expressions are developed for permanent magnets in the form of a point dipole, a tip of a magnetic force microscope, and a cylindrical magnet. In the latter case, the exponential relationship has been observed in numerous experiments but without previous interpretation

Multivariate stability of force-reflecting teleoperation: Structures of finite and infinite zeros

International Nuclear Information System (INIS)

Daniel, R.W.; McAree, P.R.

2000-01-01

This paper presents a stability analysis of force-position teleoperation under general end-effector contact. The analysis is based on the finite and infinite zero structure of the multivariable root-locus resulting from modulation of the environment stiffness. The starting point is an analysis of the stability of robot force control, motivated by the observation that the human-operator in a force reflection loop acts as a force servo, generating position commands in response to reflected force. Asymptotic root loci properties are used to establish passivity conditions on force feedback to give root locus interpretations of the well-known results that (1) feedback via the inverse joint Jacobian can lead to (kinematic) instability and that (2) passivity is preserved by kinematically proper force feedback through the transpose of the joint angle Jacobian. It is demonstrated that a fully constrained force-position teleoperation loop has an identical infinite zero structure to that of a slave manipulation under kinematically proper force control and that the dominant vibration modes of a force-position loop are fully described by a multivariable analogue of the single-input single-output pseudo-system investigated in a study by Daniel and McAree. Extension of the analysis to cover partial end-effector constraint provides a design tool for teleoperation control and serves to aid selection of teleoperation slate-arms. The paper concludes by giving a passivity condition for multiple-input multiple-output force-position teleoperation for stable contact against all environments

Crevicular Alkaline Phosphatase Activity and Rate of Tooth Movement of Female Orthodontic Subjects under Different Continuous Force Applications

Directory of Open Access Journals (Sweden)

Rohaya Megat Abdul Wahab

2013-01-01

Full Text Available Purpose. This study is aimed to compare the effects of two different orthodontic forces on crevicular alkaline phosphatase activity, rate of tooth movement, and root resorption. Materials and Methods. Twelve female subjects of class II division 1 malocclusion participated. Maxillary canines with bonded fixed appliances acted as the tested teeth, while their antagonists with no appliances acted as the controls. Canine retraction was performed using nickel titanium coil spring that delivered forces of 100 gm or 150 gm to either side. Crevicular fluid was analyzed for ALP activity, and study models were casted to measure tooth movements. Root resorption was assessed using periapical radiographs before and after the force application. Results. ALP activity at the mesial sites peaked at week 1 for 150 gm group with significant differences when compared with the 100 gm group. Cumulative canine movements were significantly greater in the 150 gm force (2.10 ± 0.50 mm than in the 100 gm force (1.57 ± 0.44 mm. No root resorption was in the maxillary canines after retraction. Conclusions. A force of 150 gm produced faster tooth movements and higher ALP activity compared with the 100 gm group and had no detrimental effects such as root resorption.

Military Force and Culture Change: Systems, Narratives, and the Social Transmission of Behavior in Counter-Terrorism Strategy

National Research Council Canada - National Science Library

Casebeer, William D

2006-01-01

.... Operationalizing culture as socially transmitted behavior, and treating culture systematically using open systems theory, best allows us to understand the perils and prospects of acting upon culture with force...

Anthropogenic forcing dominates sea level rise since 1850

DEFF Research Database (Denmark)

Jevrejeva, Svetlana; Grinsted, Aslak; Moore, John

2009-01-01

The rate of sea level rise and its causes are topics of active debate. Here we use a delayed response statistical model to attribute the past 1000 years of sea level variability to various natural (volcanic and solar radiative) and anthropogenic (greenhouse gases and aerosols) forcings. We show...... that until 1800 the main drivers of sea level change are volcanic and solar radiative forcings. For the past 200 years sea level rise is mostly associated with anthropogenic factors. Only 4 ± 1.5 cm (25% of total sea level rise) during the 20th century is attributed to natural forcings, the remaining 14 ± 1...

Delphi's new direct acting common rail injection system; Das neue Direct Acting Common Rail System von Delphi

Energy Technology Data Exchange (ETDEWEB)

Schoeppe, Detlev; Zuelch, Stefan; Geurts, Derk; Gris, Christian; Jorach, Rainer W. [Delphi Diesel Systems, Europe (United Kingdom)

2009-07-01

With the serial start of the Direct Acting Common Rail injection system with 2.000 bar Delphi Diesel Systems could supplement its product portfolio with a valuable component. In Delphi's directly propelled Common Rail injector, the Injection needle directly is set in operation with the help of a piezo-ceramic actuator instead of only controlling this with a conventional servo-hydraulic circuit indirectly. This enables a fast opening and closing of the nozzle needle possible independently from the rail pressure. The process of injection is controllable accurately at any time with the again developed two-stage needle movement amplifier. The additionally in the injector integrated fuel storage works as a 'Rail in the Injector' and improves the quality particularly during multiple injection. The injector completely works leakage-free and thereby helps to reach the future CO{sub 2} targets. The use of piezo-actuators as driving force behind the directly working injector leads to a set of requirements to the electronics. A control electronics was developed in order to head optimally the Direct Acting Injector. The sum of all advantages of the Direct Acting of CR systems enables lowest emissions with simultaneously small fuel consumption while new dimensions are reached with power density and engine torque. The authors of the contribution under consideration report on the construction, on the work principle of the Direct Acting CR system and on its performance characteristics as a basis for the premium diesel engine.

Drag on a Satellite Moving across a Spherical Galaxy: Tidal and Frictional Forces in Short-lived Encounters

Science.gov (United States)

Colpi, Monica; Pallavicini, Andrea

1998-07-01

The drag force on a satellite of mass M moving with speed V in the gravitational field of a spherically symmetric background of stars is computed. During the encounter, the stars are subject to a time-dependent force that alters their equilibrium. The resulting distortion in the stellar density field acts back to produce a force FΔ that decelerates the satellite. This force is computed using a perturbative technique known as linear response theory. In this paper, we extend the formalism of linear response to derive the correct expression for the back-reaction force FΔ that applies when the stellar system is described by an equilibrium one-particle distribution function. FΔ is expressed in terms of a suitable correlation function that couples the satellite dynamics to the unperturbed dynamics of the stars. At time t, the force depends upon the whole history of the composite system. In the formalism, we account for the shift of the stellar center of mass resulting from linear momentum conservation. The self-gravity of the response is neglected since it contributes to a higher order in the perturbation. Linear response theory applies also to the case of a satellite orbiting outside the spherical galaxy. The case of a satellite moving on a straight line, at high speed relative to the stellar dispersion velocity, is explored. We find that the satellite during its passage raises (1) global tides in the stellar distribution and (2) a wake, i.e., an overdense region behind its trail. If the satellite motion is external to the galaxy, it suffers a dissipative force that is not exclusively acting along V but acquires a component along R, the position vector relative to the center of the spherical galaxy. We derive the analytical expression of the force in the impulse approximation. In penetrating short-lived encounters, the satellite moves across the stellar distribution and the transient wake excited in the density field is responsible for most of the deceleration. We

Orbital forcing and role of the latitudinal insolation/temperature gradient

Energy Technology Data Exchange (ETDEWEB)

Davis, Basil A.S. [University of Newcastle, School of Geography, Politics and Sociology, Newcastle upon Tyne (United Kingdom); ARVE Group, ISTE, EPFL, Lausanne (Switzerland); Brewer, Simon [CEREGE, Europole de l' Arbois, Aix-en-Provence (France)

2009-02-15

Orbital forcing of the climate system is clearly shown in the Earths record of glacial-interglacial cycles, but the mechanism underlying this forcing is poorly understood. Traditional Milankovitch theory suggests that these cycles are driven by changes in high latitude summer insolation, yet this forcing is dominated by precession, and cannot account for the importance of obliquity in the Ice Age record. Here, we investigate an alternative forcing based on the latitudinal insolation gradient (LIG), which is dominated by both obliquity (in summer) and precession (in winter). The insolation gradient acts on the climate system through differential solar heating, which creates the Earths latitudinal temperature gradient (LTG) that drives the atmospheric and ocean circulation. A new pollen-based reconstruction of the LTG during the Holocene is used to demonstrate that the LTG may be much more sensitive to changes in the LIG than previously thought. From this, it is shown how LIG forcing of the LTG may help explain the propagation of orbital signatures throughout the climate system, including the Monsoon, Arctic Oscillation and ocean circulation. These relationships are validated over the last (Eemian) Interglacial, which occurred under a different orbital configuration to the Holocene. We conclude that LIG forcing of the LTG explains many criticisms of classic Milankovitch theory, while being poorly represented in climate models. (orig.)

Double-Acting Sleeve Muscle Actuator for Bio-Robotic Systems

Directory of Open Access Journals (Sweden)

Hao Zheng

2013-11-01

Full Text Available This paper presents a new type of muscle-like actuator, namely double-acting (DA sleeve muscle actuator, which is suitable for the actuation of biologically-inspired and biomedical robotic systems, especially those serving human-assistance purposes (prostheses, orthoses, etc.. Developed based on the traditional pneumatic muscle actuator, the new DA sleeve muscle incorporates a unique insert at the center. With the insert occupying the central portion of the internal volume, this new actuator enjoys multiple advantages relative to the traditional pneumatic muscle, including a consistent increase of force capacity over the entire range of motion, and a significant decrease of energy consumption in operation. Furthermore, the insert encompasses an additional chamber, which generates an extension force when pressurized. As such, this new actuator provides a unique bi-directional actuation capability, and, thus, has a potential to significantly simplify the design of a muscle actuator-powered robotic system. To demonstrate this new actuator concept, a prototype has been designed and fabricated, and experiments conducted on this prototype demonstrated the enhanced force capacity and the unique bi-directional actuation capability.

Double-Acting Sleeve Muscle Actuator for Bio-Robotic Systems

Science.gov (United States)

Zheng, Hao; Shen, Xiangrong

2014-01-01

This paper presents a new type of muscle-like actuator, namely double-acting (DA) sleeve muscle actuator, which is suitable for the actuation of biologically-inspired and biomedical robotic systems, especially those serving human-assistance purposes (prostheses, orthoses, etc.). Developed based on the traditional pneumatic muscle actuator, the new DA sleeve muscle incorporates a unique insert at the center. With the insert occupying the central portion of the internal volume, this new actuator enjoys multiple advantages relative to the traditional pneumatic muscle, including a consistent increase of force capacity over the entire range of motion, and a significant decrease of energy consumption in operation. Furthermore, the insert encompasses an additional chamber, which generates an extension force when pressurized. As such, this new actuator provides a unique bi-directional actuation capability, and, thus, has a potential to significantly simplify the design of a muscle actuator-powered robotic system. To demonstrate this new actuator concept, a prototype has been designed and fabricated, and experiments conducted on this prototype demonstrated the enhanced force capacity and the unique bi-directional actuation capability. PMID:25264492

Double-Acting Sleeve Muscle Actuator for Bio-Robotic Systems.

Science.gov (United States)

Zheng, Hao; Shen, Xiangrong

2013-11-25

This paper presents a new type of muscle-like actuator, namely double-acting (DA) sleeve muscle actuator, which is suitable for the actuation of biologically-inspired and biomedical robotic systems, especially those serving human-assistance purposes (prostheses, orthoses, etc .). Developed based on the traditional pneumatic muscle actuator, the new DA sleeve muscle incorporates a unique insert at the center. With the insert occupying the central portion of the internal volume, this new actuator enjoys multiple advantages relative to the traditional pneumatic muscle, including a consistent increase of force capacity over the entire range of motion, and a significant decrease of energy consumption in operation. Furthermore, the insert encompasses an additional chamber, which generates an extension force when pressurized. As such, this new actuator provides a unique bi-directional actuation capability, and, thus, has a potential to significantly simplify the design of a muscle actuator-powered robotic system. To demonstrate this new actuator concept, a prototype has been designed and fabricated, and experiments conducted on this prototype demonstrated the enhanced force capacity and the unique bi-directional actuation capability.

Phase-resolved fluid dynamic forces of a flapping foil energy harvester based on PIV measurements

Science.gov (United States)

Liburdy, James

2017-11-01

Two-dimensional particle image velocimetry measurements are performed in a wind tunnel to evaluate the spatial and temporal fluid dynamic forces acting on a flapping foil operating in the energy harvesting regime. Experiments are conducted at reduced frequencies (k = fc/U) of 0.05 - 0.2, pitching angle of, and heaving amplitude of A / c = 0.6. The phase-averaged pressure field is obtained by integrating the pressure Poisson equation. Fluid dynamic forces are then obtained through the integral momentum equation. Results are compared with a simple force model based on the concept of flow impulse. These results help to show the detailed force distributions, their transient nature and aide in understanding the impact of the fluid flow structures that contribute to the power production.

Gradient forces on double-negative particles in optical tweezers using Bessel beams in the ray optics regime.

Science.gov (United States)

Ambrosio, Leonardo A; Hernández-Figueroa, Hugo E

2010-11-08

Gradient forces on double negative (DNG) spherical dielectric particles are theoretically evaluated for v-th Bessel beams supposing geometrical optics approximations based on momentum transfer. For the first time in the literature, comparisons between these forces for double positive (DPS) and DNG particles are reported. We conclude that, contrary to the conventional case of positive refractive index, the gradient forces acting on a DNG particle may not reverse sign when the relative refractive index n goes from |n|>1 to |n|<1, thus revealing new and interesting trapping properties.

Validation of the Brazilian version of the childhood asthma control test (c-ACT).

Science.gov (United States)

Oliveira, Suelen G; Sarria, Edgar E; Roncada, Cristian; Stein, Renato T; Pitrez, Paulo M; Mattiello, Rita

2016-04-01

Children's perception of their symptoms has proved reliable and relevant to disease management and should be considered when assessing their asthma control. The aim of the study is to validate the Brazilian Portuguese version of the Childhood Asthma Control Test (c-ACT) in children aged 4-11 years. This is a cross-sectional study in children diagnosed with asthma undergoing treatment in a pediatric pulmonology outpatient clinic in Porto Alegre, Brazil. The translation and linguistic adaptation of the instrument were performed in accordance with international recommendations for questionnaire validation. A total of 105 participants were included, aged 4-11 years. all correlations between the total score and items on the questionnaire were significant and obtained values of r ≥ 0.3, and c-ACT means showed statistically significant differences between the GINA categories (P ACT scores than those of uncontrolled asthma group (controlled 22.0 ± 2.9 vs. uncontrolled 16.3 ± 5.3 P ACT scores than those of uncontrolled asthma group (partially controlled 20.0 ± 4.0 vs. uncontrolled 16.3 ± 5.3 P = 0.03). Correlations between the c-ACT total score and spirometry and nitric oxide were poor (r = 0.020; P = 0.866 and r = 0.035; P = 0.753, respectively). Reliability: the α-C coefficient for the c-ACT total score was 0.677 (95%CI 0.573-0763). Sensitivity to change had an effect size of 0.8 and an intraclass correlation coefficient of 0.598. No floor or ceiling effects were observed. The Brazilian version of the Childhood Asthma Control Test proved to be valid and reliable in children aged 4-11 years. © 2015 Wiley Periodicals, Inc.

A scalable platform for biomechanical studies of tissue cutting forces

International Nuclear Information System (INIS)

Valdastri, P; Tognarelli, S; Menciassi, A; Dario, P

2009-01-01

This paper presents a novel and scalable experimental platform for biomechanical analysis of tissue cutting that exploits a triaxial force-sensitive scalpel and a high resolution vision system. Real-time measurements of cutting forces can be used simultaneously with accurate visual information in order to extract important biomechanical clues in real time that would aid the surgeon during minimally invasive intervention in preserving healthy tissues. Furthermore, the in vivo data gathered can be used for modeling the viscoelastic behavior of soft tissues, which is an important issue in surgical simulator development. Thanks to a modular approach, this platform can be scaled down, thus enabling in vivo real-time robotic applications. Several cutting experiments were conducted with soft porcine tissues (lung, liver and kidney) chosen as ideal candidates for biopsy procedures. The cutting force curves show repeated self-similar units of localized loading followed by unloading. With regards to tissue properties, the depth of cut plays a significant role in the magnitude of the cutting force acting on the blade. Image processing techniques and dedicated algorithms were used to outline the surface of the tissues and estimate the time variation of the depth of cut. The depth of cut was finally used to obtain the normalized cutting force, thus allowing comparative biomechanical analysis

Gravitomagnetic Field of the Universe and Coriolis Force on the Rotating Earth

Science.gov (United States)

Veto, B.

2011-01-01

The Machian effect of distant masses of the universe in the frame of reference of the rotating Earth is demonstrated using the gravitomagnetic approach of general relativity. This effect appears in the form of a gravitomagnetic Lorentz force acting on moving bodies on the Earth. The gravitomagnetic field of the universe--deduced from a simple…

Topographical effects on wave exciting forces on huge floating structure. 2; Ogata futaishiki kaiyo kozobutsu ni sayosuru haryoku ni kansuru kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Imai, Y [Hiroshima University, Hiroshima (Japan); Okusu, M [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

1997-12-31

A method to predict drift force acting on a floating structure has been developed for a marine structure consisting of a number of floating elements, positioned in a region having a slope at the sea bottom. When a huge marine structure, such as floating air port, is located in a coastal area, scale of the overall structure is very large, of the order of scale of water depth change. The new method assumes that a marine structure consisting of an infinite number of cylindrical floating elements is installed in parallel to the seashore, where symmetrical nature of the configuration allows to predict behavior of the whole system by analyzing one element. Integration of pressures acting on structure surfaces determines the horizontal component of the drift force acting on the structure. Being influenced by topography, drift force predicted peaks at a frequency different from that for the level predicted on the assumption of constant water depth. This indicates the necessity for consideration of seabottom slope and effects of broken waves at the seashore. 6 refs., 12 figs.

Topographical effects on wave exciting forces on huge floating structure. 2; Ogata futaishiki kaiyo kozobutsu ni sayosuru haryoku ni kansuru kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Imai, Y. [Hiroshima University, Hiroshima (Japan); Okusu, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

1996-12-31

A method to predict drift force acting on a floating structure has been developed for a marine structure consisting of a number of floating elements, positioned in a region having a slope at the sea bottom. When a huge marine structure, such as floating air port, is located in a coastal area, scale of the overall structure is very large, of the order of scale of water depth change. The new method assumes that a marine structure consisting of an infinite number of cylindrical floating elements is installed in parallel to the seashore, where symmetrical nature of the configuration allows to predict behavior of the whole system by analyzing one element. Integration of pressures acting on structure surfaces determines the horizontal component of the drift force acting on the structure. Being influenced by topography, drift force predicted peaks at a frequency different from that for the level predicted on the assumption of constant water depth. This indicates the necessity for consideration of seabottom slope and effects of broken waves at the seashore. 6 refs., 12 figs.

Corrected direct force balance method for atomic force microscopy lateral force calibration

International Nuclear Information System (INIS)

Asay, David B.; Hsiao, Erik; Kim, Seong H.

2009-01-01

This paper reports corrections and improvements of the previously reported direct force balance method (DFBM) developed for lateral calibration of atomic force microscopy. The DFBM method employs the lateral force signal obtained during a force-distance measurement on a sloped surface and relates this signal to the applied load and the slope of the surface to determine the lateral calibration factor. In the original publication [Rev. Sci. Instrum. 77, 043903 (2006)], the tip-substrate contact was assumed to be pinned at the point of contact, i.e., no slip along the slope. In control experiments, the tip was found to slide along the slope during force-distance curve measurement. This paper presents the correct force balance for lateral force calibration.

Unifying kinetic approach to phoretic forces and torques onto moving and rotating convex particles

NARCIS (Netherlands)

Kröger, M.; Hütter, M.

2006-01-01

We derive general expressions and present several examples for the phoretic forces and torques acting on a translationally moving and rotating convex tracer particle, usually a submicrosized aerosol particle, assumed to be small compared to the mean free path of the surrounding nonequilibrium gas.

Optical force on diseased blood cells: Towards the optical sorting of biological matter

KAUST Repository

Gongora, J. S. Totero

2015-05-01

By employing a series of massively parallel ab-initio simulations, we study how optical forces act on biological matter subject to morphological disease. As a representative case study, we here consider the case of Plasmodium falciparum on red blood cells (RBC) illuminated by a monochromatic plane wave. Realistic parameters for the geometry and the refractive index are then taken from published experiments. In our theoretical campaign, we study the dependence of the optical force on the disease stage for different incident wavelengths. We show that optical forces change significantly with the disease, with amplitude variation in the hundreds of pN range. Our results open up new avenues for the design of new optical systems for the treatment of human disease. © 2015 Elsevier Ltd.

Maximal loads acting on legs of powered roof support unit in longwalls with bumping hazards

Institute of Scientific and Technical Information of China (English)

Stanislaw Szweda

2001-01-01

In the article the results of measurements of the resultant force in th e legs of a powered roof support unit, caused by a dynamic interaction of the ro ck mass, are discussed. The measurements have been taken in the longwalls mined with a roof fall, characterized by the highest degree of bumping hazard. It has been stated that the maximal force in the legs Fm, recorded during a dynam ic interaction of the rock mass, is proportional to the initial static force in the legs Fst,p. Th erefore a need for a careful selection of the initial load of the powered roof s upport, according to the local mining and geological conditions, results from su ch a statement. Setting the legs with the supporting load exceeding the indispen sable value for keeping the direct roof solids in balance, deteriorating the ope rational parameters of a longwall system also has a disadvantageous influence on the value of the force in the legs and the rate of its increase, caused by a dy namic interaction of the rock mass. A correct selection of the initial load caus es a decrease in the intensity of a dynamic interaction of the rock mass on powe red roof supports, which also has an advantageous influence on their life. 　　Simultaneously with the measurements of the resultant force in the legs, the vertical acceleration of the canopy was also recorded. It has enabled to prove that the exte rnal dynamic forces may act on the unit both from the roof as well as from the f loor. The changes of the force in the legs caused by dynamic phenomena intrinsic ally created in the roof and changes of the force in the legs caused by blasting explosives in the roof of the working, have been analyzed separately. It has been stated that an increase in the loads of legs, caused by intrinsi c phenomena is significantly higher than a force increase in the legs caused by blasting. It means that powered roof supports, to be operated in the workings, w here the bumping hazard occurs, will also transmit the loads

Study on force mechanism for therapeutic effect of pushing manipulation with one-finger meditation base on similarity analysis of force and waveform.

Science.gov (United States)

Fang, Lei; Fang, Min; Guo, Min-Min

2016-12-27

To reveal the force mechanism for therapeutic effect of pushing manipulation with one-finger meditation. A total of 15 participants were recruited in this study and assigned to an expert group, a skilled group and a novice group, with 5 participants in each group. Mechanical signals were collected from a biomechanical testing platform, and these data were further observed via similarity analysis and cluster analysis. Comparing the force waveforms of manipulation revealed that the manipulation forces were similar between the expert group and the skilled group (P>0.05). The mean value of vertical force was 9.8 N, and 95% CI rang from 6.37 to 14.70 N, but there were significant differences compared with the novice group (PPushing manipulation with one-finger meditation is a kind of light stimulation manipulation on the acupoint, and force characteristics of double waveforms continuously alternated during manual operation.

Tibiofemoral wear in standard and non-standard squat: implication for total knee arthroplasty.

Science.gov (United States)

Fekete, Gusztáv; Sun, Dong; Gu, Yaodong; Neis, Patric Daniel; Ferreira, Ney Francisco; Innocenti, Bernardo; Csizmadia, Béla M

2017-01-01

Due to the more resilient biomaterials, problems related to wear in total knee replacements (TKRs) have decreased but not disappeared. In the design-related factors, wear is still the second most important mechanical factor that limits the lifetime of TKRs and it is also highly influenced by the local kinematics of the knee. During wear experiments, constant load and slide-roll ratio is frequently applied in tribo-tests beside other important parameters. Nevertheless, numerous studies demonstrated that constant slide-roll ratio is not accurate approach if TKR wear is modelled, while instead of a constant load, a flexion-angle dependent tibiofemoral force should be involved into the wear model to obtain realistic results. A new analytical wear model, based upon Archard's law, is introduced, which can determine the effect of the tibiofemoral force and the varying slide-roll on wear between the tibiofemoral connection under standard and non-standard squat movement. The calculated total wear with constant slide-roll during standard squat was 5.5 times higher compared to the reference value, while if total wear includes varying slide-roll during standard squat, the calculated wear was approximately 6.25 times higher. With regard to non-standard squat, total wear with constant slide-roll during standard squat was 4.16 times higher than the reference value. If total wear included varying slide-roll, the calculated wear was approximately 4.75 times higher. It was demonstrated that the augmented force parameter solely caused 65% higher wear volume while the slide-roll ratio itself increased wear volume by 15% higher compared to the reference value. These results state that the force component has the major effect on wear propagation while non-standard squat should be proposed for TKR patients as rehabilitation exercise.

Behind the Power Curve: The Regular Air Force Pilots Shortages Effect on Air National Guard Fighter Squadrons

Science.gov (United States)

2016-04-01

in 2017. Recall from the previous retention section that there is nearly a 50% drop in the total AC fighter pilot inventory available to separate...8 Figure 3. Total Fighter Pilots by Year Group ...................................................................11 Figure 4...important for the Total Force to find an equitable balance and refine the forcing functions to produce, absorb, and sustain the dwindling fighter

Calculation of forces arising from impacting projectiles upon yielding structures

International Nuclear Information System (INIS)

Drittler, K.; Gruner, P.; Krivy, J.

1977-01-01

Calculations concerning the impact of airplanes upon nuclear power plant buildings usually imply that the building [QUOTE]acts' as a rigid target. This assumption is justified for considerations concerning the structural integrity of the building being hit. However, for investigating induced vibrations of components within the structure, this approach might-in general-be too conservative. It is expected, that yielding of the structure during impact reduces the peak values of the loads and changes the temporal behaviour of the load function which is obtained for a rigid target. To calculate the changes of the load function which are due to deformations of the structure, Riera's method is extended for the case of a yielding target. The calculations are performed with a one-dimensional model for the projectile. The presented model calculations seem to verify that the motion of the target does not have much influence on the impact force for projectiles similar to the model projectile, provided the displacement of the yielding target is small in comparison with the path covered by the free-flying projectile during a time which is equivalent to the total time of impact. (Auth.)

Shaping tissues by balancing active forces and geometric constraints

Science.gov (United States)

Foolen, Jasper; Yamashita, Tadahiro; Kollmannsberger, Philip

2016-02-01

The self-organization of cells into complex tissues during growth and regeneration is a combination of physical-mechanical events and biochemical signal processing. Cells actively generate forces at all stages in this process, and according to the laws of mechanics, these forces result in stress fields defined by the geometric boundary conditions of the cell and tissue. The unique ability of cells to translate such force patterns into biochemical information and vice versa sets biological tissues apart from any other material. In this topical review, we summarize the current knowledge and open questions of how forces and geometry act together on scales from the single cell to tissues and organisms, and how their interaction determines biological shape and structure. Starting with a planar surface as the simplest type of geometric constraint, we review literature on how forces during cell spreading and adhesion together with geometric constraints impact cell shape, stress patterns, and the resulting biological response. We then move on to include cell-cell interactions and the role of forces in monolayers and in collective cell migration, and introduce curvature at the transition from flat cell sheets to three-dimensional (3D) tissues. Fibrous 3D environments, as cells experience them in the body, introduce new mechanical boundary conditions and change cell behaviour compared to flat surfaces. Starting from early work on force transmission and collagen remodelling, we discuss recent discoveries on the interaction with geometric constraints and the resulting structure formation and network organization in 3D. Recent literature on two physiological scenarios—embryonic development and bone—is reviewed to demonstrate the role of the force-geometry balance in living organisms. Furthermore, the role of mechanics in pathological scenarios such as cancer is discussed. We conclude by highlighting common physical principles guiding cell mechanics, tissue patterning and

Shaping tissues by balancing active forces and geometric constraints

International Nuclear Information System (INIS)

Foolen, Jasper; Yamashita, Tadahiro; Kollmannsberger, Philip

2016-01-01

The self-organization of cells into complex tissues during growth and regeneration is a combination of physical–mechanical events and biochemical signal processing. Cells actively generate forces at all stages in this process, and according to the laws of mechanics, these forces result in stress fields defined by the geometric boundary conditions of the cell and tissue. The unique ability of cells to translate such force patterns into biochemical information and vice versa sets biological tissues apart from any other material. In this topical review, we summarize the current knowledge and open questions of how forces and geometry act together on scales from the single cell to tissues and organisms, and how their interaction determines biological shape and structure. Starting with a planar surface as the simplest type of geometric constraint, we review literature on how forces during cell spreading and adhesion together with geometric constraints impact cell shape, stress patterns, and the resulting biological response. We then move on to include cell–cell interactions and the role of forces in monolayers and in collective cell migration, and introduce curvature at the transition from flat cell sheets to three-dimensional (3D) tissues. Fibrous 3D environments, as cells experience them in the body, introduce new mechanical boundary conditions and change cell behaviour compared to flat surfaces. Starting from early work on force transmission and collagen remodelling, we discuss recent discoveries on the interaction with geometric constraints and the resulting structure formation and network organization in 3D. Recent literature on two physiological scenarios—embryonic development and bone—is reviewed to demonstrate the role of the force-geometry balance in living organisms. Furthermore, the role of mechanics in pathological scenarios such as cancer is discussed. We conclude by highlighting common physical principles guiding cell mechanics, tissue patterning

The Unsafe Acts and the Decision-to-Err Factors of Thai Construction Workers

OpenAIRE

Thanet Aksorn; B.H.W. Hadikusumo

2007-01-01

The unsafe acts of workers are considered as major contributors of work-related accidents and injuries on construction sites. However, not much work has been done to address the reasons why unsafe acts of workers occur particularly in construction industry. The aim of this paper therefore, is to investigate the major unsafe acts (i.e., at-risk behavior), and the decision-to-err factors causing unsafe acts. A questionnaire survey was conducted to collect data from a total of 214 workers from 2...

Radiative forcing for changes in tropospheric O3

International Nuclear Information System (INIS)

Grossman, A.S.; Wuebbles, D.J.; Grant, K.E.

1994-06-01

We have evaluated the radiative forcing for assumed changes in tropospheric O 3 in the 500-1650 cm -1 wavenumber range. The radiative forcing calculations were performed as a function of latitude as well as for a globally and seasonally averaged model atmosphere, both in a clear sky approximation and in a model containing a representative cloud distribution. The scenarios involved radiative forcing calculations for O 3 at normal atmospheric abundance and at a tropospheric abundance depleted by 25 ppbv, at each altitude, for all northern hemisphere latitudes. Normal abundances of H 2 O, CO 2 , CH 4 , and N 2 O were included in the calculations. The IR radiative forcing was calculated using a correlated k-distribution radiative transfer model. The tropospheric radiative forcing values are compared to the IPCC formulae for ozone tropospheric forcing as well as other published values to determine the validity of the correlated k-distribution approach to the radiative forcing calculations. The results for the global average atmosphere show agreement with previous results to the order of 10 percent. We conclude that the O 3 forcing is linear in the background abundance and that the radiative forcing for ozone for the globally averaged atmosphere and the latitude averaged radiative forcing in the clear sky approximation are in agreement to within 10 percent. For the case of an atmosphere in which the tropospheric ozone has been depleted by 25 ppbv at all altitudes in the northern hemisphere, the mid latitude zone contributes ∼50 percent of the forcing, tropic zone contributes ∼37 percent of the forcing and the polar zone contributes ∼13 percent of the total forcing

Report of the Defense Task Force on Sexual Harassment and Violence at the Military Service Academies

National Research Council Canada - National Science Library

2005-01-01

... Authorization Act for Fiscal Year 2004. Congress directed the Task Force to assess and make recommendations concerning how the Departments of the Army and the Navy may more effectively address sexual harassment and assault at the United...

Factors influencing initial cup stability in total hip arthroplasty.

Science.gov (United States)

Amirouche, Farid; Solitro, Giovanni; Broviak, Stefanie; Gonzalez, Mark; Goldstein, Wayne; Barmada, Riad

2014-12-01

One of the main goals in total hip replacement is to preserve the integrity of the hip kinematics, by well positioning the cup and to make sure its initial stability is congruent and attained. Achieving the latter is not trivial. A finite element model of the cup-bone interface simulating a realistic insertion and analysis of different scenarios of cup penetration, insertion, under-reaming and loading is investigated to determine certain measurable factors sensitivity to stress-strain outcome. The insertion force during hammering and its relation to the cup penetration during implantation is also investigated with the goal of determining the initial stability of the acetabular cup during total hip arthroplasty. The mathematical model was run in various configurations to simulate 1 and 2mm of under-reaming at various imposed insertion distances to mimic hammering and insertion of cup insertion into the pelvis. Surface contact and micromotion at the cup-bone interface were evaluated after simulated cup insertion and post-operative loading conditions. The results suggest a direct correlation between under-reaming and insertion force used to insert the acetabular cup on the micromotion and fixation at the cup-bone interface. While increased under-reaming and insertion force result in an increase amount of stability at the interface, approximately the same percentage of surface contact and micromotion reduction can be achieved with less insertion force. We need to exercise caution to determine the optimal configuration which achieves a good conformity without approaching the yield strength for bone. Copyright © 2014 Elsevier Ltd. All rights reserved.

Acute administration of ketamine in rats increases hippocampal BDNF and mTOR levels during forced swimming test.

Science.gov (United States)

Yang, Chun; Hu, Yi-Min; Zhou, Zhi-Qiang; Zhang, Guang-Fen; Yang, Jian-Jun

2013-03-01

Previous studies have shown that a single sub-anesthetic dose of ketamine exerts fast-acting antidepressant effects in patients and in animal models of depression. However, the underlying mechanisms are not totally understood. This study aims to investigate the effects of acute administration of different doses of ketamine on the immobility time of rats in the forced swimming test (FST) and to determine levels of hippocampal brain-derived neurotrophic factor (BDNF) and mammalian target of rapamycin (mTOR). Forty male Wistar rats weighing 180-220 g were randomly divided into four groups (n = 10 each): group saline and groups ketamine 5, 10, and 15 mg/kg. On the first day, all animals were forced to swim for 15 min. On the second day ketamine (5, 10, and 15 mg/kg, respectively) was given intraperitoneally, at 30 min before the second episode of the forced swimming test. Immobility times of the rats during the forced swimming test were recorded. The animals were then decapitated. The hippocampus was harvested for determination of BDNF and mTOR levels. Compared with group saline, administration of ketamine at a dose of 5, 10, and 15 mg/kg decreased the duration of immobility (P < 0.05 for all doses). Ketamine at doses of both 10 and 15 mg/kg showed a significant increase in the expression of hippocampal BDNF (P < 0.05 for both doses). Ketamine given at doses of 5, 10, and 15 mg/kg showed significant increases in relative levels of hippocampal p-mTOR (P < 0.05 for all doses) The antidepressant effect of ketamine might be related to the increased expression of BDNF and mTOR in the hippocampus of rats.

The Motor and the Brake of the Trailing Leg in Human Walking: Leg Force Control Through Ankle Modulation and Knee Covariance

Science.gov (United States)

Toney, Megan E.; Chang, Young-Hui

2016-01-01

Human walking is a complex task, and we lack a complete understanding of how the neuromuscular system organizes its numerous muscles and joints to achieve consistent and efficient walking mechanics. Focused control of select influential task-level variables may simplify the higher-level control of steady state walking and reduce demand on the neuromuscular system. As trailing leg power generation and force application can affect the mechanical efficiency of step-to-step transitions, we investigated how joint torques are organized to control leg force and leg power during human walking. We tested whether timing of trailing leg force control corresponded with timing of peak leg power generation. We also applied a modified uncontrolled manifold analysis to test whether individual or coordinated joint torque strategies most contributed to leg force control. We found that leg force magnitude was adjusted from step-to-step to maintain consistent leg power generation. Leg force modulation was primarily determined by adjustments in the timing of peak ankle plantar-flexion torque, while knee torque was simultaneously covaried to dampen the effect of ankle torque on leg force. We propose a coordinated joint torque control strategy in which the trailing leg ankle acts as a motor to drive leg power production while trailing leg knee torque acts as a brake to refine leg power production. PMID:27334888

Ciclosporine A asxay: RIA or HPLC, plasma or total blood

International Nuclear Information System (INIS)

Lapalus, P.; Garraffo, R.; Krebs, B.; Lapalus, F.

1985-01-01

The two methods now in force for ciclosporine A assay are radioimmunoassay (RIA) and high pressure liquid chromatography (HPLC) in various biological media (plasma, serum, total blood). The advantages and disadvantages of the two methods are presented [fr

Regimes of seasonal air-sea interaction and implications for performance of forced simulations

Energy Technology Data Exchange (ETDEWEB)

Wu, Renguang [Center for Ocean-Land-Atmosphere Studies, Calverton, MD (United States); Kirtman, Ben P. [Center for Ocean-Land-Atmosphere Studies, Calverton, MD (United States); George Mason University, School of Computational Sciences, Fairfax, VA (United States)

2007-09-15

Sea surface temperature (SST) anomalies can induce anomalous convection through surface evaporation and low-level moisture convergence. This SST forcing of the atmosphere is indicated in a positive local rainfall-SST correlation. Anomalous convection can feedback on SST through cloud-radiation and wind-evaporation effects and wind-induced oceanic mixing and upwelling. These atmospheric feedbacks are reflected in a negative local rainfall-SST tendency correlation. As such, the simultaneous rainfall-SST and rainfall-SST tendency correlations can indicate the nature of local air-sea interactions. Based on the magnitude of simultaneous rainfall-SST and rainfall-SST tendency correlations, the present study identifies three distinct regimes of local air-sea interactions. The relative importance of SST forcing and atmospheric forcing differs in these regimes. In the equatorial central-eastern Pacific and, to a smaller degree, in the western equatorial Indian Ocean, SST forcing dominates throughout the year and the surface heat flux acts mainly as a damping term. In the tropical Indo-western Pacific Ocean regions, SST forcing and atmospheric forcing dominate alternatively in different seasons. Atmospheric forcing dominates in the local warm/rainy season. SST forcing dominates with a positive wind-evaporation feedback during the transition to the cold/dry season. SST forcing also dominates during the transition to the warm/rainy season but with a negative cloud-radiation feedback. The performance of atmospheric general circulation model simulations forced by observed SST is closely linked to the regime of air-sea interaction. The forced simulations have good performance when SST forcing dominates. The performance is low or poor when atmospheric forcing dominates. (orig.)

ESB Clinical Biomechanics Award 2008: Complete data of total knee replacement loading for level walking and stair climbing measured in vivo with a follow-up of 6-10 months.

Science.gov (United States)

Heinlein, Bernd; Kutzner, Ines; Graichen, Friedmar; Bender, Alwina; Rohlmann, Antonius; Halder, Andreas M; Beier, Alexander; Bergmann, Georg

2009-05-01

Detailed information about the loading of the knee joint is required for various investigations in total knee replacement. Up to now, gait analysis plus analytical musculo-skeletal models were used to calculate the forces and moments acting in the knee joint. Currently, all experimental and numerical pre-clinical tests rely on these indirect measurements which have limitations. The validation of these methods requires in vivo data; therefore, the purpose of this study was to provide in vivo loading data of the knee joint. A custom-made telemetric tibial tray was used to measure the three forces and three moments acting in the implant. This prosthesis was implanted into two subjects and measurements were obtained for a follow-up of 6 and 10 months, respectively. Subjects performed level walking and going up and down stairs using a self-selected comfortable speed. The subjects' activities were captured simultaneously with the load data on a digital video tape. Customized software enabled the display of all information in one video sequence. The highest mean values of the peak load components from the two subjects were as follows: during level walking the forces were 276%BW (percent body weight) in axial direction, 21%BW (medio-lateral), and 29%BW (antero-posterior). The moments were 1.8%BW*m in the sagittal plane, 4.3%BW*m (frontal plane) and 1.0%BW*m (transversal plane). During stair climbing the axial force increased to 306%BW, while the shear forces changed only slightly. The sagittal plane moment increased to 2.4%BW*m, while the frontal and transversal plane moments decreased slightly. Stair descending produced the highest forces of 352%BW (axial), 35%BW (medio-lateral), and 36%BW (antero-posterior). The sagittal and frontal plane moments increased to 2.8%BW*m and 4.6%BW*m, respectively, while the transversal plane moment changed only slightly. Using the data obtained, mechanical simulators can be programmed according to realistic load profiles. Furthermore

Magnus force and inertia properties of magnetic vortices in weak ferromagnets

International Nuclear Information System (INIS)

Zvezdin, A.K.; Zvezdin, K.A.

2010-01-01

The question of the Magnus force in weak ferromagnets acting on magnetic vortices (Bloch lines), within domain boundary has been investigated and the general formula of the Magnus force has been derived. It is shown that the Magnus force is non-zero in most types domain boundaries and determined by the average sublattice magnetization, Dzyaloshinskii coupling constants and exchange interaction between the sublattices. Generalized expressions have been obtained for the effective Langrangian and Rayleigh functions in weak ferromagnets allowing for their vortex structure. The mass of a vortex was considered and the value m * ∼ 10 -14 g/cm was obtained for YFeO 3 . The dynamic bending of the domain boundary in the presence of a moving vortex has been analyzed. A formula has been obtained, which describes the dependence of the vortex velocity in a motionless domain boundary upon the magnetic-field.

Leveraging intellectual capital through Lewin's Force Field Analysis: The case of software development companies

Directory of Open Access Journals (Sweden)

Alexandru Capatina

2017-09-01

Full Text Available This article presents an original conceptual framework for the strategic management of intellectual capital assets in software development companies. The framework is based on Lewin's Force Field Analysis. The framework makes it possible to assess software company managers’ opinions regarding the way driving and restraining forces affect the pillars of intellectual capital. The capacity to adapt to change is vital for companies in knowledge-intensive industries. Accordingly, this study examined a sample of 74 Romanian software development companies. The aim was to help companies benefit from managing the driving and restraining forces acting upon the pillars of intellectual capital (human, structural, and relational. The effects of the driving forces, quantified by PathMaker software's Force Field Tool, were observed to be greater than the restraining forces for each pillar of intellectual capital. This paper contributes by showing the explanatory power of this framework. The framework thus offers a tool that helps managers drive change in their organizations through effective intellectual capital management. Furthermore, this article describes how to encourage the implementation of changes that create value for software development companies.

29 CFR 779.253 - What is included in computing the total annual inflow volume.

Science.gov (United States)

2010-07-01

... FAIR LABOR STANDARDS ACT AS APPLIED TO RETAILERS OF GOODS OR SERVICES Employment to Which the Act May... taxes and other charges which the enterprise must pay for such goods. Generally, all charges will be... computing the total annual inflow volume. The goods which the establishment purchases or receives for resale...

Analysis of Electromagnetics Forces on Magnetically Suspended High-Speed Trains

Directory of Open Access Journals (Sweden)

Daniel Mayer

2004-01-01

Full Text Available High-speed superexpresses (HSST developed by Japanese airlines (JAL are based on the electrodynamics principle of magnetic suspension. The track contains short-circuited coils and interaction between them and superconductive coils in the vehicle produces its suspension. The paper includes a mathematical model for traction electrodynamics suspension device HSST represented by a system of linear differential equations with coefficients varying in time. Numerical analysis of this model fields the velocity-dependent lift and drag forces acting on the system. The time distribution of the lift force exhibits certain oscillations that may be suppressed by suitable placement of several superconductive levitation wings in the vehicle. The results obtained are in a good agreement with the knowledge found by various authors on prototype vehicles.

Cruising in afterburner: Air force fuel use and emerging energy policy

International Nuclear Information System (INIS)

Lucia, David J.

2011-01-01

Operational and mission efficiency were estimated for Air Force fighters, bombers and transports from fuel use data from 2001 through 2008 as reported in the Air Force Total Cost of Ownership (AFTOC) database. This analysis estimated efficiency in terms of the best performance theoretically possible for each platform based upon the energy available in the fuel expended. Operational efficiency considered aircraft operations in general, without regard for the type of mission. Mission efficiency only considered use of allocated fuel for combat (non-training) sorties. The cost associated with fuel inefficiency of the combined fighter, bomber and tanker force were estimated based on the fiscal year 2008 costs of fuel, fully burdened to include the cost of aerial refueling. The total cost of operational inefficiency was estimated at $5 billion per year. The fully burdened cost of mission inefficiency added an additional $3.6 billion for a total per year cost estimate of $8.6 billion. This represents 21.5% of the $40 billion portion of the 2009 budget dedicated to modernization. A business case for force-structure change is presented, which describes how these cost savings can be leveraged for modernization. - Highlights: → I assess how efficiently the United States Air Force uses fuel for aviation. → I estimate the cost associated with fuel inefficiency. → Improved technology can dramatically improve fuel efficiency. → There is potentially a large cost savings associated with improved fuel efficiency. → I present a business case to leverage this cost savings for modernization.

Total quality is people

International Nuclear Information System (INIS)

Vogel, C.E.

1991-01-01

Confronted by changing market conditions and increased global competition, in 1983 the Commercial Nuclear Fuel Division (CNFD) of Westinghouse Electric embarked on an ambitious plan to make total quality the centerpiece of its long-term business strategy. Five years later, the division's efforts in making continuous quality improvement a way of life among its more than 2,000 employees gained national recognition when it was named a charter recipient of the Malcolm Baldridge National Quality Award. What CNFD achieved during the 1980s was a cultural transformation, characterized by an empowered work force committed to a common vision. The company's quality program development strategy is described

An instrumented implant for in vivo measurement of contact forces and contact moments in the shoulder joint.

Science.gov (United States)

Westerhoff, P; Graichen, F; Bender, A; Rohlmann, A; Bergmann, G

2009-03-01

To improve implant design, fixation and preclinical testing, implant manufacturers depend on realistic data of loads acting on the shoulder joint. Furthermore, these data can help to optimize physiotherapeutic treatment and to advise patients in their everyday living conditions. Calculated shoulder joint loads vary extremely among different authors [Anglin C, Wyss UP, Pichora DR. Glenohumeral contact forces. Proc Inst Mech Eng [H] 2000;214:637-44]. Additionally the moments acting in the joint caused by friction or incongruent articular surfaces, for example, are not implemented in most models. An instrumented shoulder joint implant was developed to measure the contact forces and the contact moments acting in the glenohumeral joint. This article provides a detailed description of the implant, containing a nine-channel telemetry unit, six load sensors and an inductive power supply, all hermetically sealed inside the implant. The instrumented implant is based on a clinically proven BIOMET Biomodular shoulder replacement and was calibrated before implantation by using complex mathematical calculation routines in order to achieve an average measuring precision of approximately 2%.

Analysis of PM Magnetization Field Effects on the Unbalanced Magnetic Forces due to Rotor Eccentricity in BLDC Motors

Directory of Open Access Journals (Sweden)

S. Mahdiuon-Rad

2013-08-01

Full Text Available This paper investigates both static and dynamic eccentricities in single phase brushless DC (BLDC motors and analyzes the effect of the PM magnetization field on unbalanced magnetic forces acting on the rotor. Three common types of PM magnetization field patterns including radial, parallel and sinusoidal magnetizations are considered. In both static and dynamic eccentricities, harmonic components of the unbalanced magnetic forces on the rotor are extracted and analyzed. Based on simulation results, the magnetization fields that produce the lowest and highest unbalanced magnetic forces are determined in rotor eccentricity conditions.

Implementation by environmental administration of the Finnish air pollution control act

Energy Technology Data Exchange (ETDEWEB)

Haapaniemi, J. [Turku Univ. (Finland). Dept. of Political Science

1995-12-31

The aim of this research is to show how the general wording of the Air Pollution Control Act which came into force in 1982 has been given practical meanings. The main interest is the administrational implementation of the aims of the air pollution legislation for regulation of industrial activities and the energy sector. The article focuses on the decisions and the decision-making process through the Air Pollution Control Act with its relatively flexible norms. It gives a view of air pollution control practices and its problems, especially concerning sulphur emissions of whose control there is already lot of experiences. The grounds for resolutions given according to the Air Pollution Control Act and the possibility of public participation in their making are the centre of attention here. The greatest interest is cases on the decisions made by applying general governmental decisions, especially regulations concerning coal-fired power plants, and the regulations for sulphur dioxide emissions, in the governmental decision of 1987. (author)

Yugoslavia-Act on Liability for Nuclear Damage of 19 April 1978

International Nuclear Information System (INIS)

Anon.

1979-01-01

This Act, which came into force eight days after its publication, is based to a great extent on the provisions of the 1963 Vienna Convention on Civil Liability for Nuclear Damage, ratified by Yugoslavia on 12 August 1977. Under the Act, a nuclear operator is held absolutely liable for any nuclear damage caused by a nuclear indicent occurring in his installation. This liability is limited to 450 million dinars (approximately 22 million US$). To cover his liability, an operator must take out insurance or other financial security, whose amount will be determinated by the competent authority according to the characteristics of the installation involved but in no event should it be below 150 million dinars. Within the meaning of the Act, the operator may be an organisation of associated labour which has obtained site approval, licences for test runs and entry into operation of the installation, or any person recognised as such by the State. (NEA) [fr

Implementation by environmental administration of the Finnish air pollution control act

Energy Technology Data Exchange (ETDEWEB)

Haapaniemi, J [Turku Univ. (Finland). Dept. of Political Science

1996-12-31

The aim of this research is to show how the general wording of the Air Pollution Control Act which came into force in 1982 has been given practical meanings. The main interest is the administrational implementation of the aims of the air pollution legislation for regulation of industrial activities and the energy sector. The article focuses on the decisions and the decision-making process through the Air Pollution Control Act with its relatively flexible norms. It gives a view of air pollution control practices and its problems, especially concerning sulphur emissions of whose control there is already lot of experiences. The grounds for resolutions given according to the Air Pollution Control Act and the possibility of public participation in their making are the centre of attention here. The greatest interest is cases on the decisions made by applying general governmental decisions, especially regulations concerning coal-fired power plants, and the regulations for sulphur dioxide emissions, in the governmental decision of 1987. (author)

A Race to Force the Issue: A Use-of-Force Doctrine in Policing

Science.gov (United States)

2017-03-01

reactions to the police shooting of an unarmed teen and the 21 Ibid., 2. 22 Michael Wines , “Are the...alleged excessive force claims to be determined based on the “totality of the circumstances” as perceived by the officer without the benefit of “20/20...Michael Wines , “Are Police Bigoted?” In it, Wines wrote, “The death of the black teenager shined a spotlight on the plague of shootings of black men by

Nonlinear Dynamics of Cantilever-Sample Interactions in Atomic Force Microscopy

Science.gov (United States)

Cantrell, John H.; Cantrell, Sean A.

2010-01-01

The interaction of the cantilever tip of an atomic force microscope (AFM) with the sample surface is obtained by treating the cantilever and sample as independent systems coupled by a nonlinear force acting between the cantilever tip and a volume element of the sample surface. The volume element is subjected to a restoring force from the remainder of the sample that provides dynamical equilibrium for the combined systems. The model accounts for the positions on the cantilever of the cantilever tip, laser probe, and excitation force (if any) via a basis set of set of orthogonal functions that may be generalized to account for arbitrary cantilever shapes. The basis set is extended to include nonlinear cantilever modes. The model leads to a pair of coupled nonlinear differential equations that are solved analytically using a matrix iteration procedure. The effects of oscillatory excitation forces applied either to the cantilever or to the sample surface (or to both) are obtained from the solution set and applied to the to the assessment of phase and amplitude signals generated by various acoustic-atomic force microscope (A-AFM) modalities. The influence of bistable cantilever modes of on AFM signal generation is discussed. The effects on the cantilever-sample surface dynamics of subsurface features embedded in the sample that are perturbed by surface-generated oscillatory excitation forces and carried to the cantilever via wave propagation are accounted by the Bolef-Miller propagating wave model. Expressions pertaining to signal generation and image contrast in A-AFM are obtained and applied to amplitude modulation (intermittent contact) atomic force microscopy and resonant difference-frequency atomic force ultrasonic microscopy (RDF-AFUM). The influence of phase accumulation in A-AFM on image contrast is discussed, as is the effect of hard contact and maximum nonlinearity regimes of A-AFM operation.

Origin of the Magnus force on a vortex in fermion superfluids and superconductors

International Nuclear Information System (INIS)

Simanek, E.

1995-01-01

Starting from the time-dependent version of the Feynman-Hellmann theorem, the Magnus force acting on a vortex in fermion superfluid is expressed via the adiabatic curvature over the space of vortex positions. With use of the Bogoliubov--de Gennes approximation, the Magnus force in a homogeneous superfluid at T=0 is shown to originate from virtual transitions between the lowest quasiparticle core bound states. Nonadiabatic corrections to the curvature are obtained to second order in vortex velocity. The adiabatic approximation is shown to break down at a critical velocity equal to the vortex velocity in the first Landau level. The effect of elastic scattering on the Magnus force is discussed in terms of the relaxation-time approximation. It is suggested that this approximation is appropriate only for a large-scale vortex motion. In this case, the effective Magnus force is drastically reduced when the elastic-scattering rate exceeds the core excitation frequency. We conjecture that quantum vortex tunneling is governed by a local Magnus force obtained from the Berry phase approach

MTS-MD of Biomolecules Steered with 3D-RISM-KH Mean Solvation Forces Accelerated with Generalized Solvation Force Extrapolation.

Science.gov (United States)

Omelyan, Igor; Kovalenko, Andriy

2015-04-14

We developed a generalized solvation force extrapolation (GSFE) approach to speed up multiple time step molecular dynamics (MTS-MD) of biomolecules steered with mean solvation forces obtained from the 3D-RISM-KH molecular theory of solvation (three-dimensional reference interaction site model with the Kovalenko-Hirata closure). GSFE is based on a set of techniques including the non-Eckart-like transformation of coordinate space separately for each solute atom, extension of the force-coordinate pair basis set followed by selection of the best subset, balancing the normal equations by modified least-squares minimization of deviations, and incremental increase of outer time step in motion integration. Mean solvation forces acting on the biomolecule atoms in conformations at successive inner time steps are extrapolated using a relatively small number of best (closest) solute atomic coordinates and corresponding mean solvation forces obtained at previous outer time steps by converging the 3D-RISM-KH integral equations. The MTS-MD evolution steered with GSFE of 3D-RISM-KH mean solvation forces is efficiently stabilized with our optimized isokinetic Nosé-Hoover chain (OIN) thermostat. We validated the hybrid MTS-MD/OIN/GSFE/3D-RISM-KH integrator on solvated organic and biomolecules of different stiffness and complexity: asphaltene dimer in toluene solvent, hydrated alanine dipeptide, miniprotein 1L2Y, and protein G. The GSFE accuracy and the OIN efficiency allowed us to enlarge outer time steps up to huge values of 1-4 ps while accurately reproducing conformational properties. Quasidynamics steered with 3D-RISM-KH mean solvation forces achieves time scale compression of conformational changes coupled with solvent exchange, resulting in further significant acceleration of protein conformational sampling with respect to real time dynamics. Overall, this provided a 50- to 1000-fold effective speedup of conformational sampling for these systems, compared to conventional MD

Investigation of a cuboidal permanent magnet’s force exerted on a robotic capsule

Directory of Open Access Journals (Sweden)

Yang W

2014-08-01

Full Text Available Wan’an Yang,1 Chengbing Tang,2 Fengqing Qin1 1School of Computer and Information Engineering, Yibin University, Yibin, 2CNPC Chuanqing Geophysical Prospecting Company Research Center Computer Department, Chengdu, Sichuan, People’s Republic of China Abstract: To control and drive a robotic capsule accurately from outside a patient’s body, we present a schema in which the capsule enclosing the imaging device, circuits, batteries, etc is looped by a permanent magnet ring that acts as an actuator. A cuboidal permanent magnet situated outside the patient's body attracts or pushes the magnet ring from different directions to make the capsule move or rotate. A mathematic model of attractive or repulsive force that the cuboidal magnet exerts on the magnet ring is presented for accurate calculation of force. The experiments showed that the measuring force was in agreement with the theoretical one, and the relations between the dimensions of the cuboidal magnet and force are useful to produce a cuboidal magnet with optimal shape to get appropriate force. Keywords: control and drive, robotic capsule, permanent magnet ring, optimal dimension, force model

Self-consistent mean field forces in turbulent plasmas: Current and momentum relaxation

International Nuclear Information System (INIS)

Hegna, C.C.

1997-08-01

The properties of turbulent plasmas are described using the two-fluid equations. Under some modest assumptions, global constraints for the turbulent mean field forces that act on the ion and electron fluids are derived. These constraints imply a functional form for the parallel mean field forces in the Ohm's law and the momentum balance equation. These forms suggest that the fluctuations attempt to relax the plasma to a state where both the current and the bulk plasma momentum are aligned along the mean magnetic field with proportionality constants that are global constants. Observations of flow profile evolution during discrete dynamo activity in reversed field pinch experiments are interpreted

Atomic Energy Commission Act, 2000 (Act 588)

International Nuclear Information System (INIS)

2000-01-01

Act 588 of the Republic of Ghana entitled, Atomic Energy Commission Act, 2000, amends and consolidates the Atomic Energy Commission Act, 204 of 1963 relating to the establishment of the Atomic Energy Commission. Act 588 makes provision for the Ghana Atomic Energy Commission to establish more institutes for the purpose of research in furtherance of its functions and also promote the commercialization of its research and development results. (E.A.A.)

Magnus force, Aharonov-Bohm effect, and berry phase in superfluids

International Nuclear Information System (INIS)

Sonin, E.

2001-01-01

The present paper is an attempt to bring together two points of view in order to find a source of disagreement. I restrict myself with the problem of the Galilean invariant quantum Bose-liquid described by the Gross-Pitaevskii theory. At large scales the theory yields equations of the hydrodynamics of an ideal inviscous liquid. In presence of an ensemble of sound waves (phonons) with the Planck distribution, which is characterized by a locally defined normal velocity, one obtains the two-fluid hydrodynamics. The momentum balance in the area around a moving vortex demonstrates the existence of the Iordanskii force. I also discuss the Berry phase. The Berry phase and the Magnus forces are proportional to the total current circulation at large distances. But the total current circulation contains a normal-fluid contribution, which is proportional to the Iordanski force. Taking this contribution into account, the Berry-phase analysis agrees with the momentum-balance approach. (orig.)

Investigation of Calibrating Force Transducer Using Sinusoidal Force

International Nuclear Information System (INIS)

Zhang Li; Wang Yu; Zhang Lizhe

2010-01-01

Sinusoidal force calibration method was studied several years before at Physikalisch-Technische Bundesanstalt (PTB). A similar dynamic force calibration system is developed at Changcheng Institute of Metrology and Measurement (CIMM). It uses electro-dynamic shakers to generate dynamic force in the range from 1 N to 20 kN, and heterodyne laser interferometers are used for acceleration measurement. The force transducer to be calibrated is mounted on the shaker, and a mass block is screwed on the top of force transducer, the sinusoidal forces realized by accelerated load masses are traceable to acceleration and mass according to the force definition. The methods of determining Spatial-dependent acceleration on mass block and measuring the end mass of force transducer in dynamic force calibration are discussed in this paper.

Countermovement jump height: gender and sport-specific differences in the force-time variables.

Science.gov (United States)