Mathematical description of tooth flank surface of globoidal worm gear with straight axial tooth profile

Science.gov (United States)

Połowniak, Piotr; Sobolak, Mariusz

2017-12-01

In this article, a mathematical description of tooth flank surface of the globoidal worm and worm wheel generated by the hourglass worm hob with straight tooth axial profile is presented. The kinematic system of globoidal worm gear is shown. The equation of globoid helix and tooth axial profile of worm is derived to determine worm tooth surface. Based on the equation of meshing the contact lines are obtained. The mathematical description of globoidal worm wheel tooth flank is performed on the basis of contact lines and generating the tooth side by the extreme cutting edge of worm hob. The presented mathematical model of tooth flank of TA worm and worm wheel can be used e.g. to analyse the contact pattern of the gear.

Recent advances in engineering of tooth and tooth structures using postnatal dental cells

Directory of Open Access Journals (Sweden)

Masaki J. Honda

2010-02-01

This review focuses on the performance of postnatal and adult dental cells that have been used for generating teeth. Their ability to contribute to tooth development was assessed in the omentum or in the tooth socket. Adult dental cells were limited in their potential owing to various parameters. From these results described, new approaches for regenerated teeth are proposed in this review. One strategy to replace teeth is tooth root engineering using tissue from postnatal teeth. Since the enamel organ epithelium disappears after tooth maturation, the epithelial rest cells of Malassez were evaluated to determine their capacity to generate enamel. From these results, it is suggested that erupted mature teeth have cell sources with the capacity to produce tooth root. The development of biological approaches for tooth root regeneration using postnatal dental cells is promising and remains one of the greatest challenges in the dental field in the years to come.

Multivariate image analysis of laser-induced photothermal imaging used for detection of caries tooth

Science.gov (United States)

El-Sherif, Ashraf F.; Abdel Aziz, Wessam M.; El-Sharkawy, Yasser H.

2010-08-01

Time-resolved photothermal imaging has been investigated to characterize tooth for the purpose of discriminating between normal and caries areas of the hard tissue using thermal camera. Ultrasonic thermoelastic waves were generated in hard tissue by the absorption of fiber-coupled Q-switched Nd:YAG laser pulses operating at 1064 nm in conjunction with a laser-induced photothermal technique used to detect the thermal radiation waves for diagnosis of human tooth. The concepts behind the use of photo-thermal techniques for off-line detection of caries tooth features were presented by our group in earlier work. This paper illustrates the application of multivariate image analysis (MIA) techniques to detect the presence of caries tooth. MIA is used to rapidly detect the presence and quantity of common caries tooth features as they scanned by the high resolution color (RGB) thermal cameras. Multivariate principal component analysis is used to decompose the acquired three-channel tooth images into a two dimensional principal components (PC) space. Masking score point clusters in the score space and highlighting corresponding pixels in the image space of the two dominant PCs enables isolation of caries defect pixels based on contrast and color information. The technique provides a qualitative result that can be used for early stage caries tooth detection. The proposed technique can potentially be used on-line or real-time resolved to prescreen the existence of caries through vision based systems like real-time thermal camera. Experimental results on the large number of extracted teeth as well as one of the thermal image panoramas of the human teeth voltanteer are investigated and presented.

Tooth - abnormal colors

Science.gov (United States)

... medlineplus.gov/ency/article/003065.htm Tooth - abnormal colors To use the sharing features on this page, please enable JavaScript. Abnormal tooth color is any color other than white to yellowish- ...

Orthodontic Tooth Movement: A Historic Prospective.

Science.gov (United States)

Will, Leslie A

2016-01-01

The earliest report on orthodontic tooth movement in the English literature was published in 1911. Oppenheim carried out studies on baboons to determine what histologic changes occurred during tooth movement. Reitan and many others carried out research into the nature of tooth movement. The pressure-tension model of tooth movement developed from these studies, whereby the two sides of the tooth responded to forces as if in isolation. A second theory, proposed by Stuteville in 1938, was the hydraulic theory of tooth movement. In this theory, fluid from the vasculature, lymphatic system and intercellular spaces responds to the forces of tooth movement, damping the force and limiting movement. Bien and Baumrind expanded on this theory with their own studies in the 1960s. It is clear that both the pressure-tension and fluid flow concepts have merit, but considerable work needs to be done to ascertain the details so that tooth movement can be managed and controlled. © 2016 S. Karger AG, Basel.

Mechanism of Calcite Co-Orientation in the Sea Urchin Tooth

Energy Technology Data Exchange (ETDEWEB)

Killian, Christopher; Metzler, Rebecca; Gong, Y. U. T.; Olson, Ian; Aizenberg, Joanna; Politi, Yael; Wilt, Fred; Scholl, Andreas; Young, Anthony; Doran, Andrew; Kunz, Martin; Tamura, Nobumichi; Coppersmith, Susan; Gilbert, P. U. P. A.

2009-12-01

Sea urchin teeth are remarkable and complex calcite structures, continuously growing at the forming end and self-sharpening at the mature grinding tip. The calcite (CaCO{sub 3}) crystals of tooth components, plates, fibers, and a high-Mg polycrystalline matrix, have highly co-oriented crystallographic axes. This ability to co-orient calcite in a mineralized structure is shared by all echinoderms. However, the physico-chemical mechanism by which calcite crystals become co-oriented in echinoderms remains enigmatic. Here, we show differences in calcite c-axis orientations in the tooth of the purple sea urchin (Strongylocentrotus purpuratus), using high-resolution X-ray photoelectron emission spectromicroscopy (X-PEEM) and microbeam X-ray diffraction ({mu}XRD). All plates share one crystal orientation, propagated through pillar bridges, while fibers and polycrystalline matrix share another orientation. Furthermore, in the forming end of the tooth, we observe that CaCO{sub 3} is present as amorphous calcium carbonate (ACC). We demonstrate that co-orientation of the nanoparticles in the polycrystalline matrix occurs via solid-state secondary nucleation, propagating out from the previously formed fibers and plates, into the amorphous precursor nanoparticles. Because amorphous precursors were observed in diverse biominerals, solid-state secondary nucleation is likely to be a general mechanism for the co-orientation of biomineral components in organisms from different phyla.

[Assessment of tooth bleaching efficacy with spectrophotometer].

Science.gov (United States)

Zhu, Wenhao; Liu, Chang; Pan, Jie

2014-06-01

To analyze the changes in CIE L*, a*, and b* at cervical, body, and incisal sites after tooth bleaching by using a spectrophotometer. Sixty-seven intact and healthy maxillary central incisors were in-vestigated. These incisors were darker than A3 according to the Vita Classical shade guide. The CIE tooth shade parameters L*, a*, and b* were simultaneously recorded at three tooth areas (cervical, body, and incisal) with a spectrophotometer before and after tooth bleaching (35%H2O2 coordinating with Beyond whitening accelerator irradiating). The shade dif-ferential (DeltaE) was calculated. ANOVA, paired t-test, and Pearson correlation analysis were used for data analysis. The efficacy rates of tooth bleaching were satisfactory, with 86.6%, 86.6%, and 85.1% in the cervical, body, and incisal sites, respectively. The average values of DeltaE were 5.09, 4.44, and 4.40 in the cervical, body, and incisal sites. Tooth bleaching significantly increased L* and significantly decreased a* and b* in all tooth areas (P spectrophotometer could objectively evaluate the whitening effect of tooth bleaching at the different tooth sites. The tooth bleaching system (35%H202 coordinating with Beyond whitening accelerator irradiating) exerts powerful bleaching actions in most of the tooth areas investigated. The order of tooth bleaching effectiveness is cervicalbody>incisal. Yellow coloration is decreased mainly at the cervical site, and brightness was increased mostly at theincisal site. The effectiveness of tooth bleaching increases as the baseline b* value increases.

Overview of Tooth Disorders

Science.gov (United States)

... teeth using a thin resin cement. Bleaching, or tooth whitening, is a process used by dentists to lighten ... following? Damage to only the hard outer surface (enamel) of the tooth An incomplete fracture of a ...

Dental radiography: tooth enamel EPR dose assessment from Rando phantom measurements

International Nuclear Information System (INIS)

Aragno, D.; Fattibene, P.; Onori, S.

2000-01-01

Electron paramagnetic resonance dosimetry of tooth enamel is now established as a suitable method for individual dose reconstruction following radiation accidents. The accuracy of the method is limited by some confounding factors, among which is the dose received due to medical x-ray irradiation. In the present paper the EPR response of tooth enamel to endoral examination was experimentally evaluated using an anthropomorphic phantom. The dose to enamel for a single exposure of a typical dental examination performed with a new x-ray generation unit working at 65 kVp gave rise to a CO 2 -signal of intensity similar to that induced by a dose of about 2 mGy of 60 Co. EPR measurements were performed on the entire tooth with no attempt to separate buccal and lingual components. Also the dose to enamel for an orthopantomography exam was estimated. It was derived from TLD measurements as equivalent to 0.2 mGy of 60 Co. In view of application to risk assessment analysis, in the present work the value for the ratio of the reference dose at the phantom surface measured with TLD to the dose at the tooth measured with EPR was determined. (author)

Dental Caries (Tooth Decay)

Science.gov (United States)

... Materials Contact Us Home Research Data & Statistics Dental Caries (Tooth Decay) Dental caries (tooth decay) remains the most prevalent chronic disease ... adults, even though it is largely preventable. Although caries has significantly decreased for most Americans over the ...

Dental Caries (Tooth Decay)

Science.gov (United States)

... Contact Us Home Research Data & Statistics Share Dental Caries (Tooth Decay) Dental caries (tooth decay) remains the most prevalent chronic disease ... adults, even though it is largely preventable. Although caries has significantly decreased for most Americans over the ...

Immunohistochemistry of the intercellular matrix components and the epithelio-mesenchymal junction of the human tooth germ

DEFF Research Database (Denmark)

Matthiessen, M E; Olsen, B E; Moe, D

1994-01-01

The immunohistochemical localization of heparan sulphate, collagen type I, III and IV, laminin, tenascin, plasma- and cellular fibronectin was studied in tooth germs from human fetuses. The lamina basalis ameloblastica or membrana preformativa, which separates the pre-ameloblasts from the pre...

Fluoridation and tooth wear in Irish adults.

LENUS (Irish Health Repository)

Burke, F M

2010-10-01

The aim of this study was to determine the prevalence of tooth wear in adults in Ireland and its relationship with water fluoridation. The National Survey of Adult Oral Health was conducted in 2000\\/2001. Tooth wear was determined using a partial mouth examination assessing the upper and lower anterior teeth. A total of 2456 subjects were examined. In this survey, increasing levels and severity of tooth wear were associated with ageing. Men were more affected by tooth wear and were more likely to be affected by severe tooth wear than women. It was found that age, and gender were significant predictors of tooth wear (P < 0.01). Overall, there was no significant relationship between fluoridation and tooth wear in this study.

A Survey of tooth morphology teaching methods employed in the United Kingdom and Ireland.

Science.gov (United States)

Lone, M; McKenna, J P; Cryan, J F; Downer, E J; Toulouse, A

2018-01-15

Tooth morphology is a central component of the dental curriculum and is applicable to all dental specialities. Traditional teaching methods are being supplemented with innovative strategies to tailor teaching and accommodate the learning styles of the recent generation of students. An online survey was compiled and distributed to the staff involved in teaching tooth morphology in the United Kingdom and Ireland to assess the importance of tooth morphology in the dentistry curriculum and the methodologies employed in teaching. The results of the survey show that tooth morphology constitutes a small module in the dental curriculum. It is taught in the first 2 years of the dental curriculum but is applicable in the clinical years and throughout the dental career. Traditional teaching methods, lecture and practical, are being augmented with innovative teaching including e-learning via virtual learning environment, tooth atlas and e-books leading to blended learning. The majority of the schools teach both normal dental anatomy and morphologic variations of dental anatomy and utilise plastic teeth for practical and examination purposes. Learning the 3D aspects of tooth morphology was deemed important by most of the respondents who also agreed that tooth morphology is a difficult topic for the students. Despite being core to the dental curriculum, overall minimal time is dedicated to the delivery of tooth morphology, creating a reliance on the student to learn the material. New forms of delivery including computer-assisted learning tools should help sustain learning and previously acquired knowledge. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Investigation of EPR signals on tooth enamel

Energy Technology Data Exchange (ETDEWEB)

Pavlenko, A; Mironova-Ulmane, N; Polakov, M; Riekstina, D [Institute of Solid State Physics, University of Latvia, Riga (Latvia)

2007-12-15

Calcified tissues are involved in continues metabolic process in human organism exchanging a number of chemical elements with environment. The rate of biochemical reactions is tissue dependent and the slowest one at the tooth enamel, the most mineralized tissue of human organism. The long time stability and unique chemical composition make tooth enamel suitable for number of application. The assessment of individual radiation dose by Electron Paramagnetic Resonance (EPR) and evaluations of elemental composition by Instrumentation Neutron Activation Analysis (INAA) are the well known procedures where properties of tooth enamel intensively used. The current work is focused on investigation of EPR signals and determination of chemical composition on several teeth samples having different origin. The EPR spectra and INAA element content of milk tooth, caries tooth, and paradantose tooth have been compared to each other. The results showed that the intensity of EPR signal is much higher for the caries tooth than the for paradantose tooth that is in agreement with depleted Ca content.

Tooth whitening: what we now know.

Science.gov (United States)

Carey, Clifton M

2014-06-01

Current research about tooth whitening shows that it is safe and effective when manufacturer's protocol is followed, yet there are risks of which the profession and users should be aware. This update provides a summary of current research and assessment of the safety and efficacy of tooth whitening regimens. Tooth whitening has become one of the most frequently requested dental procedures by the public. The public has come to demand whiter, more perfect smiles and in response many choices for tooth whitening have been made available. These include home-based products such as toothpastes, gels, and films, as well as in-office based systems where products containing highly concentrated bleaching agents are applied under professional supervision. The profession and public have been aware of certain risks related to tooth whitening such as increased tooth sensitivity and gingival irritation. New research has shown that there are other risks such as tooth surface roughening and softening, increased potential for demineralization, degradation of dental restorations, and unacceptable color change of dental restorations. The new research is also focused on optimizing whitening procedures to reduce tooth sensitivity and to increase the persistence of the whitening. Current reports in the literature are reviewed that are related to the use of peroxide based whitening methods. These reports include in vitro studies for method optimization and mechanism as well as clinical studies on effects of various whitening regimens. When manufacturer's instructions are followed, hydrogen peroxide and carbamide peroxide based tooth whitening is safe and effective. Patients should be informed of the risks associated with tooth whitening and instructed on identification of adverse occurrences so that they may seek professional help as needed. Copyright © 2014 Elsevier Inc. All rights reserved.

Detection and Localization of Tooth Breakage Fault on Wind Turbine Planetary Gear System considering Gear Manufacturing Errors

Directory of Open Access Journals (Sweden)

Y. Gui

2014-01-01

Full Text Available Sidebands of vibration spectrum are sensitive to the fault degree and have been proved to be useful for tooth fault detection and localization. However, the amplitude and frequency modulation due to manufacturing errors (which are inevitable in actual planetary gear system lead to much more complex sidebands. Thus, in the paper, a lumped parameter model for a typical planetary gear system with various types of errors is established. In the model, the influences of tooth faults on time-varying mesh stiffness and tooth impact force are derived analytically. Numerical methods are then utilized to obtain the response spectra of the system with tooth faults with and without errors. Three system components (including sun, planet, and ring gears with tooth faults are considered in the discussion, respectively. Through detailed comparisons of spectral sidebands, fault characteristic frequencies of the system are acquired. Dynamic experiments on a planetary gear-box test rig are carried out to verify the simulation results and these results are of great significances for the detection and localization of tooth faults in wind turbines.

Evolution of high tooth replacement rates in sauropod dinosaurs.

Science.gov (United States)

D'Emic, Michael D; Whitlock, John A; Smith, Kathlyn M; Fisher, Daniel C; Wilson, Jeffrey A

2013-01-01

Tooth replacement rate can be calculated in extinct animals by counting incremental lines of deposition in tooth dentin. Calculating this rate in several taxa allows for the study of the evolution of tooth replacement rate. Sauropod dinosaurs, the largest terrestrial animals that ever evolved, exhibited a diversity of tooth sizes and shapes, but little is known about their tooth replacement rates. We present tooth replacement rate, formation time, crown volume, total dentition volume, and enamel thickness for two coexisting but distantly related and morphologically disparate sauropod dinosaurs Camarasaurus and Diplodocus. Individual tooth formation time was determined by counting daily incremental lines in dentin. Tooth replacement rate is calculated as the difference between the number of days recorded in successive replacement teeth. Each tooth family in Camarasaurus has a maximum of three replacement teeth, whereas each Diplodocus tooth family has up to five. Tooth formation times are about 1.7 times longer in Camarasaurus than in Diplodocus (315 vs. 185 days). Average tooth replacement rate in Camarasaurus is about one tooth every 62 days versus about one tooth every 35 days in Diplodocus. Despite slower tooth replacement rates in Camarasaurus, the volumetric rate of Camarasaurus tooth replacement is 10 times faster than in Diplodocus because of its substantially greater tooth volumes. A novel method to estimate replacement rate was developed and applied to several other sauropodomorphs that we were not able to thin section. Differences in tooth replacement rate among sauropodomorphs likely reflect disparate feeding strategies and/or food choices, which would have facilitated the coexistence of these gigantic herbivores in one ecosystem. Early neosauropods are characterized by high tooth replacement rates (despite their large tooth size), and derived titanosaurs and diplodocoids independently evolved the highest known tooth replacement rates among archosaurs.

Evolution of high tooth replacement rates in sauropod dinosaurs.

Directory of Open Access Journals (Sweden)

Michael D D'Emic

Full Text Available BACKGROUND: Tooth replacement rate can be calculated in extinct animals by counting incremental lines of deposition in tooth dentin. Calculating this rate in several taxa allows for the study of the evolution of tooth replacement rate. Sauropod dinosaurs, the largest terrestrial animals that ever evolved, exhibited a diversity of tooth sizes and shapes, but little is known about their tooth replacement rates. METHODOLOGY/PRINCIPAL FINDINGS: We present tooth replacement rate, formation time, crown volume, total dentition volume, and enamel thickness for two coexisting but distantly related and morphologically disparate sauropod dinosaurs Camarasaurus and Diplodocus. Individual tooth formation time was determined by counting daily incremental lines in dentin. Tooth replacement rate is calculated as the difference between the number of days recorded in successive replacement teeth. Each tooth family in Camarasaurus has a maximum of three replacement teeth, whereas each Diplodocus tooth family has up to five. Tooth formation times are about 1.7 times longer in Camarasaurus than in Diplodocus (315 vs. 185 days. Average tooth replacement rate in Camarasaurus is about one tooth every 62 days versus about one tooth every 35 days in Diplodocus. Despite slower tooth replacement rates in Camarasaurus, the volumetric rate of Camarasaurus tooth replacement is 10 times faster than in Diplodocus because of its substantially greater tooth volumes. A novel method to estimate replacement rate was developed and applied to several other sauropodomorphs that we were not able to thin section. CONCLUSIONS/SIGNIFICANCE: Differences in tooth replacement rate among sauropodomorphs likely reflect disparate feeding strategies and/or food choices, which would have facilitated the coexistence of these gigantic herbivores in one ecosystem. Early neosauropods are characterized by high tooth replacement rates (despite their large tooth size, and derived titanosaurs and

Endodontic Treatment of an Anomalous Anterior Tooth with the Aid of a 3-dimensional Printed Physical Tooth Model.

Science.gov (United States)

Byun, Chanhee; Kim, Changhwan; Cho, Seungryong; Baek, Seung Hoon; Kim, Gyutae; Kim, Sahng G; Kim, Sun-Young

2015-06-01

Endodontic treatment of tooth formation anomalies is a challenge to clinicians and as such requires a complete understanding of the aberrant root canal anatomy followed by careful root canal disinfection and obturation. Here, we report the use of a 3-dimensional (3D) printed physical tooth model including internal root canal structures for the endodontic treatment of a challenging tooth anomaly. A 12-year-old boy was referred for endodontic treatment of tooth #8. The tooth showed class II mobility with swelling and a sinus tract in the buccal mucosa and periapical radiolucency. The tooth presented a very narrow structure between the crown and root by distal concavity and a severely dilacerated root. Moreover, a perforation site with bleeding and another ditching site were identified around the cervical area in the access cavity. A translucent physical tooth model carrying the information on internal root canal structures was built through a 3-step process: data acquisition by cone-beam computed tomographic scanning, virtual modeling by image processing, and manufacturing by 3D printing. A custom-made guide jig was then fabricated to achieve a safe and precise working path to the root canal. Endodontic procedures including access cavity preparation were performed using the physical tooth model and the guide jig. At the 7-month follow-up, the endodontically treated tooth showed complete periapical healing with no clinical signs and symptoms. This case report describes a novel method of endodontic treatment of an anomalous maxillary central incisor with the aid of a physical tooth model and a custom-made guide jig via 3D printing technique. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Primary culprit for tooth loss!!

OpenAIRE

Nuvvula, Sailavanya; Chava, Vijay Kumar; Nuvvula, Sivakumar

2016-01-01

Aim: In order to facilitate planning for dental health services and to progress strategies to continue the reduction in tooth loss, it is important to identify the factors that result in such loss. therefore the aim of the study is to investigate the major cause for tooth extraction. Objective: to examine whether the major reason for tooth extraction is dental caries or periodontal disease. Materials and Methods: The study is carried out among the dental practitioners in our district. A quest...

Atypical Odontalgia (Phantom Tooth Pain)

Science.gov (United States)

... atypical facial pain, phantom tooth pain, or neuropathic orofacial pain, is characterized by chronic pain in a tooth ... such as a specialist in oral medicine or orofacial pain. The information contained in this monograph is for ...

Tooth breakage in patients injected with 224Ra

International Nuclear Information System (INIS)

Sonnabend, E.; Spiess, H.; Mays, C.W.

1986-01-01

Tooth breakage has been common among the 224 Ra patients, especially those injected as teenagers. The fracture of 1 or more teeth was reported by 26% (8/31) of boys and 23% (7/30) of girls injected with 224 Ra at 16-20 years of age. Combining results from all age groups, the incidence of tooth fractures increased significantly with dose (P=0.01). Unlike the normal loss of permanent teeth by periodontal disease, in which the entire tooth is lost, the tooth loss following 224 Ra injection was primarily from tooth resorption near the gum line causing the tooth crowns to break off easily. Eventually the tooth roots may either become incorporated into the jawbone or are resorbed and replaced with bone. These tooth fractures resembled those observed in the U.S. radium dial painters and in dogs injected with bone-seeking α-emitters. (orig.)

Autotransplantation donor tooth site harvesting using piezosurgery

OpenAIRE

Ylikontiola, Leena P.; S?ndor, George K.

2016-01-01

Abstract Background: The harvesting of a tooth as a candidate for tooth autotransplantation requires that the delicate dental tissues around the tooth be minimally traumatized. This is especially so for the periradicular tissues of the tooth root and the follicular tissues surrounding the crown. The aim of this report is to describe the use of piezosurgery as an attempt at morbidity reduction in the harvesting of teeth for autotransplantation. Methods: A piezosurgical handpiece and its ...

Proteomic analysis of human tooth pulp: proteomics of human tooth.

Science.gov (United States)

Eckhardt, Adam; Jágr, Michal; Pataridis, Statis; Mikšík, Ivan

2014-12-01

The unique pulp-dentin complex demonstrates strong regenerative potential, which enables it to respond to disease and traumatic injury. Identifying the proteins of the pulp-dentin complex is crucial to understanding the mechanisms of regeneration, tissue calcification, defense processes, and the reparation of dentin by dental pulp. The lack of knowledge of these proteins limits the development of more efficient therapies. The proteomic profile of human tooth pulp was investigated and compared with the proteome of human dentin and blood. The samples of tooth pulp were obtained from 5 sound permanent human third molars of 5 adults (n = 5). The extracted proteins were separated by 2-dimensional gel electrophoresis, analyzed by nano-liquid chromatography tandem mass spectrometry, and identified by correlating mass spectra to the proteomic databases. A total of 342 proteins were identified with high confidence, and 2 proteins were detected for the first time in an actual human sample. The identified tooth pulp proteins have a variety of functions: structural, catalytic, transporter, protease activity, immune response, and many others. In a comparison with dentin and blood plasma, 140 (pulp/dentin) shared proteins were identified, 37 of which were not observed in plasma. It can be suggested that they might participate in the unique pulp-dentin complex. This proteomic investigation of human tooth pulp, together with the previously published study of human dentin, is one of the most comprehensive proteome lists of human teeth to date. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Test Tube Tooth: The Next Big Thing.

Science.gov (United States)

Yadav, Preeti; Tahir, Mohammed; Yadav, Harsh; Sureka, Rakshit; Garg, Aarti

2016-06-01

Unlike some vertebrates and fishes, humans do not have the capacity for tooth regeneration after the loss of permanent teeth. Although artificial replacement with removable dentures, fixed prosthesis and implants is possible through advances in the field of prosthetic dentistry, it would be ideal to recreate a third set of natural teeth to replace lost dentition. For many years now, researchers in the field of tissue engineering have been trying to bioengineer dental tissues as well as whole teeth. In order to attain a whole tooth through dental engineering, that has the same or nearly same biological, mechanical and physical properties of a natural tooth, it's necessary to deal with all the cells and tissues which are concerned with the formation, maintenance and repair of the tooth. In this article we review the steps involved in odontogenesis or organogenesis of a tooth and progress in the bioengineering of a whole tooth.

Multiphoton microscopy imaging of developing tooth germs

Directory of Open Access Journals (Sweden)

Pei-Yu Pan

2014-01-01

Conclusion: In this study, a novel multiphoton microscopy database of images from developing tooth germs in mice was set up. We confirmed that multiphoton laser microscopy is a powerful tool for investigating the development of tooth germ and is worthy for further application in the study of tooth regeneration.

A Radiographic Study of Fused and Geminated Tooth

Energy Technology Data Exchange (ETDEWEB)

Park, Chul Jae; Lee, Sang Rae [Dept. of Oral Radiology, College of Dentistry, Kyunhee University, Seoul (Korea, Republic of)

1990-02-15

The incidence and several characteristic features of fused and geminated teeth were studied radiographically, with full mouth periapical radiogram and pantomogram, in 4201 patients of mixed dentition and 5358 patients of permanent dentition. The obtained results were as follows: 1. The prevalence was revealed to 2.86%, 0.32%, 0.33%, and 0.06% in deciduous fused tooth, permanent fused tooth, deciduous geminated tooth and permanent geminated tooth respectively, and these anomalies were occurred in female more than male. 2. Fused teeth were observed predominantly in lower anterior teeth area, especially in lateral incisor and canine region, and many cases of deciduous geminated tooth were observed in upper central incisor region. 3. Congenital missing rates of succedaneous tooth in deciduous fused teeth were 57.1%, 85.7%, 71.0%, 69.0% in upper right and left central-lateral incisor regions, lower right and left lateral incisor-canine regions, respectively. 4. Prevalence of dental caries was 42.3%, 18.8% and 5.6% in deciduous fused, deciduous geminated and permanent fused tooth, respectively. 5. In classifying of fused and geminated teeth into 9 type, by following appearance such as number of crown, root, pulp chamber and pulp canal of those teeth, it was more favorable that Type I (2 crown, 2 root, 2 pulp chamber, 2 pulp canal) in deciduous fused tooth and Type IX (1 crown, 1 root, 1 pulp chamber, 1 pulp canal) in permanent used tooth, deciduous and permanent geminated tooth.

A Radiographic Study of Fused and Geminated Tooth

International Nuclear Information System (INIS)

Park, Chul Jae; Lee, Sang Rae

1990-01-01

The incidence and several characteristic features of fused and geminated teeth were studied radiographically, with full mouth periapical radiogram and pantomogram, in 4201 patients of mixed dentition and 5358 patients of permanent dentition. The obtained results were as follows: 1. The prevalence was revealed to 2.86%, 0.32%, 0.33%, and 0.06% in deciduous fused tooth, permanent fused tooth, deciduous geminated tooth and permanent geminated tooth respectively, and these anomalies were occurred in female more than male. 2. Fused teeth were observed predominantly in lower anterior teeth area, especially in lateral incisor and canine region, and many cases of deciduous geminated tooth were observed in upper central incisor region. 3. Congenital missing rates of succedaneous tooth in deciduous fused teeth were 57.1%, 85.7%, 71.0%, 69.0% in upper right and left central-lateral incisor regions, lower right and left lateral incisor-canine regions, respectively. 4. Prevalence of dental caries was 42.3%, 18.8% and 5.6% in deciduous fused, deciduous geminated and permanent fused tooth, respectively. 5. In classifying of fused and geminated teeth into 9 type, by following appearance such as number of crown, root, pulp chamber and pulp canal of those teeth, it was more favorable that Type I (2 crown, 2 root, 2 pulp chamber, 2 pulp canal) in deciduous fused tooth and Type IX (1 crown, 1 root, 1 pulp chamber, 1 pulp canal) in permanent used tooth, deciduous and permanent geminated tooth.

Analysis of tooth tissues using Raman spectroscopy

International Nuclear Information System (INIS)

Timchenko, E.V.; Timchenko, P.E.; Kulabukhova, A.Yu.; Volova, L.T.; Rosenbaum, A.Yu.

2016-01-01

The results of experimental studies of healthy tooth tissue and tooth tissues during caries disease are presented. Features of Raman spectrum of tooth tissues during caries disease are obtained: the main changes are detected at wavenumbers 956 cm -1 .1069 cm -1 . corresponding to phosphates. and 1241 cm -1 . 1660 cm -1 . corresponding to collagen III and collagen I. respectively. Were introduced criteria allowing to detect caries and to identify weakening of tooth tissues. preceding the caries. The reliability of research results is confirmed by scanning electron microscopy. (paper)

Primary culprit for tooth loss!!

Directory of Open Access Journals (Sweden)

Sailavanya Nuvvula

2016-01-01

Full Text Available Aim: In order to facilitate planning for dental health services and to progress strategies to continue the reduction in tooth loss, it is important to identify the factors that result in such loss. therefore the aim of the study is to investigate the major cause for tooth extraction. Objective: to examine whether the major reason for tooth extraction is dental caries or periodontal disease. Materials and Methods: The study is carried out among the dental practitioners in our district. A questionnaire containing 10 items was distributed to the dental practitioners, which included age, gender, no of teeth indicated for extraction, the reason for extraction, and the periodontal parameters that are involved with the extracted tooth and were requested to complete the form on every extraction they were to undertake. the study form was collected at the end of the study period and data was subjected to statistical analysis. Results: A total of 502 patients were enrolled during the study period, and a total of 1055 teeth were extracted for several reasons. we found that 51.14%extractions are due to dental caries in case of 20-30years age groups, which is more when compared to tooth loss due to periodontal diseases in this age group. whereas in case of >40years of age group periodontal diseases account for 54.11%, and dental caries accounts for only 29.11%. Showing more teeth were lost due to periodontal disease. Conclusion: therefore we concluded that, caries is the dominant reason for extraction in patients with 20–30 years of age while periodontal disease accounts for the majority of tooth extraction in patients older than 40 years.

Tooth wear and wear investigations in dentistry.

Science.gov (United States)

Lee, A; He, L H; Lyons, K; Swain, M V

2012-03-01

Tooth wear has been recognised as a major problem in dentistry. Epidemiological studies have reported an increasing prevalence of tooth wear and general dental practitioners see a greater number of patients seeking treatment with worn dentition. Although the dental literature contains numerous publications related to management and rehabilitation of tooth wear of varying aetiologies, our understanding of the aetiology and pathogenesis of tooth wear is still limited. The wear behaviour of dental biomaterials has also been extensively researched to improve our understanding of the underlying mechanisms and for the development of restorative materials with good wear resistance. The complex nature of tooth wear indicates challenges for conducting in vitro and in vivo wear investigations and a clear correlation between in vitro and in vivo data has not been established. The objective was to critically review the peer reviewed English-language literature pertaining to prevalence and aetiology of tooth wear and wear investigations in dentistry identified through a Medline search engine combined with hand-searching of the relevant literature, covering the period between 1960 and 2011. © 2011 Blackwell Publishing Ltd.

Is tooth wear in the primary dentition predictive of tooth wear in the permanent dentition? Report from a longitudinal study.

LENUS (Irish Health Repository)

Harding, M A

2010-03-01

To determine the prevalence of tooth wear in the permanent dentition of a sample of 12-year-old school children and establish whether an association exists between tooth wear recorded now and tooth wear recorded in their primary dentition at age five.

Combined periodontic-orthodonticendodontic interdisciplinary approach in the treatment of periodontally compromised tooth.

Science.gov (United States)

Deepa, D; Mehta, D S; Puri, Viren K; Shetty, Sadashiva

2010-04-01

Orthodontic treatment in adult patients is one of the most frequently encountered components involving multidisciplinary approaches. In the present report, a 28-year-old male patient was treated for localized chronic periodontitis with pocket formation, mobility, pathologic migration and malalignment of maxillary left lateral incisor tooth #22. The periodontal therapy included motivation, education and oral-hygiene instructions (O.H.I.), scaling and root planing and periodontal flap surgery. Subsequently on resolution of periodontal inflammation, orthodontic therapy was carried out using the orthodontic aligner for a period of 6 months. Post-treatment (3 years) results showed complete resolution of infrabony pocket with significant bone fill, reduced tooth mobility and complete alignment of the affected maxillary left lateral incisor, thus restoring the esthetics and function.

Accelerated tooth eruption in children with diabetes mellitus.

Science.gov (United States)

Lal, Shantanu; Cheng, Bin; Kaplan, Selma; Softness, Barney; Greenberg, Ellen; Goland, Robin S; Lalla, Evanthia; Lamster, Ira B

2008-05-01

The objective of this study was to evaluate tooth eruption in 6- to 14-year-old children with diabetes mellitus. Tooth eruption status was assessed for 270 children with diabetes and 320 control children without diabetes. Data on important diabetes-related variables were collected. Analyses were performed using logistic regression models. Children with diabetes exhibited accelerated tooth eruption in the late mixed dentition period (10-14 years of age) compared to healthy children. For both case patients and control subjects the odds of a tooth being in an advanced eruptive stage were significantly higher among girls than boys. There was also a trend associating gingival inflammation with expedited tooth eruption in both groups. No association was found between the odds of a tooth being in an advanced stage of eruption and hemoglobin A(1c) or duration of diabetes. Patients with higher body mass index percentile demonstrated statistically higher odds for accelerated tooth eruption, but the association was not clinically significant. Children with diabetes exhibit accelerated tooth eruption. Future studies need to ascertain the role of such aberrations in dental development and complications such as malocclusion, impaired oral hygiene, and periodontal disease. The standards of care for children with diabetes should include screening and referral programs aimed at oral health promotion and disease prevention.

Biologically Based Restorative Management of Tooth Wear

Directory of Open Access Journals (Sweden)

Martin G. D. Kelleher

2012-01-01

Full Text Available The prevalence and severity of tooth wear is increasing in industrialised nations. Yet, there is no high-level evidence to support or refute any therapeutic intervention. In the absence of such evidence, many currently prevailing management strategies for tooth wear may be failing in their duty of care to first and foremost improve the oral health of patients with this disease. This paper promotes biologically sound approaches to the management of tooth wear on the basis of current best evidence of the aetiology and clinical features of this disease. The relative risks and benefits of the varying approaches to managing tooth wear are discussed with reference to long-term follow-up studies. Using reference to ethical standards such as “The Daughter Test”, this paper presents case reports of patients with moderate-to-severe levels of tooth wear managed in line with these biologically sound principles.

Tooth loss prevalence among cardiac males and females

International Nuclear Information System (INIS)

Bokhari, S.A.H.; Khan, A.A.; Butt, A.K.

2007-01-01

Objective of study was to observe differences of tooth loss prevalence in males and females with Cardiac diseases Poor oral health, tooth loss and periodontal diseases have been reported to be associated with coronary heart diseases. Studies report gender differences in prevalence of cardiac diseases and tooth loss. This paper presents gender differences of tooth loss in cardiac patients of a cardiac hospital of Lahore, Pakistan. Methodology: Age matched Cardiac males and females attending OPD of the Punjab Institute of Cardiology (PIC), Lahore were included in the study. Personal and health-related information were questioned and noted. Oral examination was performed for recording of missing teeth. 1200 CHD study subjects with age-range of 30 to 80 years were enrolled for study. 1045 age matched, 766 (73.30%) males and 279 (26.70%) females were examined for tooth loss. 852 (81.53%) genders had at least one tooth missing. 599 (78.19) males and 253 (90.68%) females were observed with mean tooth loss of 7.5 (SD 8.720) and 11.15 (SD 10.375)respectively statistical association among them was also significant (P= 0.000) with OR of 2.339. More subjects (76.29%) showed a loss of 1-15 teeth that I was also significant among males and females. Tooth loss was significant in age groups of 41-50 years (P=0.001) and 51-60 years (P=0.000) Gender differences of tooth loss prevalence among CHD Subjects were significant with more risk for males as compared to females. (author)

Functional constraints on tooth morphology in carnivorous mammals

Directory of Open Access Journals (Sweden)

Smits Peter D

2012-08-01

Full Text Available Abstract Background The range of potential morphologies resulting from evolution is limited by complex interacting processes, ranging from development to function. Quantifying these interactions is important for understanding adaptation and convergent evolution. Using three-dimensional reconstructions of carnivoran and dasyuromorph tooth rows, we compared statistical models of the relationship between tooth row shape and the opposing tooth row, a static feature, as well as measures of mandibular motion during chewing (occlusion, which are kinetic features. This is a new approach to quantifying functional integration because we use measures of movement and displacement, such as the amount the mandible translates laterally during occlusion, as opposed to conventional morphological measures, such as mandible length and geometric landmarks. By sampling two distantly related groups of ecologically similar mammals, we study carnivorous mammals in general rather than a specific group of mammals. Results Statistical model comparisons demonstrate that the best performing models always include some measure of mandibular motion, indicating that functional and statistical models of tooth shape as purely a function of the opposing tooth row are too simple and that increased model complexity provides a better understanding of tooth form. The predictors of the best performing models always included the opposing tooth row shape and a relative linear measure of mandibular motion. Conclusions Our results provide quantitative support of long-standing hypotheses of tooth row shape as being influenced by mandibular motion in addition to the opposing tooth row. Additionally, this study illustrates the utility and necessity of including kinetic features in analyses of morphological integration.

Heritable patterns of tooth decay in the permanent dentition: principal components and factor analyses.

Science.gov (United States)

Shaffer, John R; Feingold, Eleanor; Wang, Xiaojing; Tcuenco, Karen T; Weeks, Daniel E; DeSensi, Rebecca S; Polk, Deborah E; Wendell, Steve; Weyant, Robert J; Crout, Richard; McNeil, Daniel W; Marazita, Mary L

2012-03-09

Dental caries is the result of a complex interplay among environmental, behavioral, and genetic factors, with distinct patterns of decay likely due to specific etiologies. Therefore, global measures of decay, such as the DMFS index, may not be optimal for identifying risk factors that manifest as specific decay patterns, especially if the risk factors such as genetic susceptibility loci have small individual effects. We used two methods to extract patterns of decay from surface-level caries data in order to generate novel phenotypes with which to explore the genetic regulation of caries. The 128 tooth surfaces of the permanent dentition were scored as carious or not by intra-oral examination for 1,068 participants aged 18 to 75 years from 664 biological families. Principal components analysis (PCA) and factor analysis (FA), two methods of identifying underlying patterns without a priori surface classifications, were applied to our data. The three strongest caries patterns identified by PCA recaptured variation represented by DMFS index (correlation, r = 0.97), pit and fissure surface caries (r = 0.95), and smooth surface caries (r = 0.89). However, together, these three patterns explained only 37% of the variability in the data, indicating that a priori caries measures are insufficient for fully quantifying caries variation. In comparison, the first pattern identified by FA was strongly correlated with pit and fissure surface caries (r = 0.81), but other identified patterns, including a second pattern representing caries of the maxillary incisors, were not representative of any previously defined caries indices. Some patterns identified by PCA and FA were heritable (h(2) = 30-65%, p = 0.043-0.006), whereas other patterns were not, indicating both genetic and non-genetic etiologies of individual decay patterns. This study demonstrates the use of decay patterns as novel phenotypes to assist in understanding the multifactorial nature of dental caries.

Use of ultrasound Doppler to determine tooth vitality in a discolored tooth after traumatic injury: its prospects and limitations

Directory of Open Access Journals (Sweden)

Yong-Wook Cho

2014-02-01

Full Text Available When a tooth shows discoloration and does not respond to the cold test or electric pulp test (EPT after a traumatic injury, its diagnosis can be even more difficult due to the lack of proper diagnostic methods to evaluate its vitality. In these case reports, we hope to demonstrate that ultrasound Doppler might be successfully used to evaluate the vitality of the tooth after trauma, and help reduce unnecessary endodontic treatments. In all three of the present cases, the teeth were discolored after traumatic injuries and showed negative responses to the cold test and EPT. However, they showed distinctive vital reactions in the ultrasound Doppler test during the whole observation period. In the first case, the tooth color returned to normal, and the tooth showed a positive response to the cold test and EPT at 10 wk after the injury. In the second case, the tooth color had returned to its normal shade at 10 wk after the traumatic injury but remained insensitive to the cold test and EPT. In the third case, the discoloration was successfully treated with vital tooth bleaching.

Tooth Retained Implant: No More an Oxymoron

Directory of Open Access Journals (Sweden)

Divya Bhat

2011-03-01

Full Text Available Introduction: Periodontally af-fected teeth are treated in one of the two ways. (1 Tooth retention after periodontal surgery, in which the degree of regeneration achieved is unpredictable. (2 Tooth extrac-tion and implant placement. Implants have an osseointegrated surface which does not provide adequate shock absorption. Regeneration can be achieved by resecting the crown of the affected tooth and submerging the root. This technique has not had a clinical application so far as the tooth becomes difficult to restore. Placing an implant within the root can make the retained root restorable. At the same time, as the implant is placed within the root surface it achieves a periodontal integration which dampens occlusal forces better than osseointegration. Therefore, such a “tooth retained implant” may serve as an additional treatment option with significant benefits over tooth retention and implant placement alone. The hypothesis: Implants placed within retained roots have shown cementum deposition and attachment of periodontal ligament fibers over their surface. This periodontal attachment may be able to dam-pen forces better than in an osseointegrated implant. Moreover, since an implant is being placed, the crown of the tooth can be resected and submerged. This prevents epithelial migration, allows for the periodontal ligament cells to populate the wound and favors regeneration.Evaluation of the hypothesis: The technique of placing implants within cavities prepared in the root and then submerging them are simple for any practitioner placing implants routinely.

Autogenous Transplantation for Replacing a Hopeless Tooth.

Science.gov (United States)

Zakershahrak, Mehrsa; Moshari, Amirabbas; Vatanpour, Mehdi; Khalilak, Zohreh; Jalali Ara, Afsoon

2017-01-01

Autogenous tooth transplantation (ATT) is a simple and reasonable choice for replacing the missing teeth when a proper donor tooth is available. This report presents a case of successful ATT of a maxillary right third molar for replacement of mandibular right second molar with a concomitant endodontic-periodontal disease. The mandibular second molar was believed to be hopeless due to a severe damage to coronal tooth structure, inappropriate root canal treatment and apical radiolucency. After extraction of mandibular second molar and maxillary third molar (the donor), the tooth was re-implanted into the extracted socket of second molar site. Root canal therapy was then performed. After 3 years, clinical and radiographic examinations revealed satisfying results, with no signs and symptoms. The patient is asymptomatic and the transplanted tooth is still functional with no signs of marginal periodontal pathosis. Radiographies showed bone regeneration in the site of previous extensive periapical lesion, normal periodontal ligament with no signs of root resorption.

21 CFR 872.3580 - Preformed gold denture tooth.

Science.gov (United States)

2010-04-01

... tooth in a fixed or removable partial denture. (b) Classification. Class I (general controls). The... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Preformed gold denture tooth. 872.3580 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3580 Preformed gold denture tooth. (a...

Combined periodontic-orthodontic-endodontic interdisciplinary approach in the treatment of periodontally compromised tooth

Directory of Open Access Journals (Sweden)

Deepa D

2010-01-01

Full Text Available Orthodontic treatment in adult patients is one of the most frequently encountered components involving multidisciplinary approaches. In the present report, a 28-year-old male patient was treated for localized chronic periodontitis with pocket formation, mobility, pathologic migration and malalignment of maxillary left lateral incisor tooth #22. The periodontal therapy included motivation, education and oral-hygiene instructions (O.H.I., scaling and root planing and periodontal flap surgery. Subsequently on resolution of periodontal inflammation, orthodontic therapy was carried out using the orthodontic aligner for a period of 6 months. Post-treatment (3 years results showed complete resolution of infrabony pocket with significant bone fill, reduced tooth mobility and complete alignment of the affected maxillary left lateral incisor, thus restoring the esthetics and function.

Flexible, wireless, inductively coupled surface coil resonator for EPR tooth dosimetry

International Nuclear Information System (INIS)

Schreiber, Wilson; Petryakov, Sergey V.; Kmiec, Maciej M.; Feldman, Matthew A.; Wood, Victoria A.; Boyle, Holly K.; Flood, Ann Barry; Williams, Benjamin B.; Swartz, Harold M.; Meaney, Paul M.

2016-01-01

Managing radiation injuries following a catastrophic event where large numbers of people may have been exposed to life-threatening doses of ionizing radiation relies on the availability of biodosimetry to assess whether individuals need to be triaged for care. Electron Paramagnetic Resonance (EPR) tooth dosimetry is a viable method to accurately estimate the amount of ionizing radiation to which an individual has been exposed. In the intended measurement conditions and scenario, it is essential that the measurement process be fast, straightforward and provides meaningful and accurate dose estimations for individuals in the expected measurement conditions. The sensing component of a conventional L-band EPR spectrometer used for tooth dosimetry typically consists of a surface coil resonator that is rigidly, physically attached to the coupler. This design can result in cumbersome operation, limitations in teeth geometries that may be measured and hinder the overall utility of the dosimeter. A novel surface coil resonator has been developed for the currently existing L-band (1.15 GHz) EPR tooth dosimeter for the intended use as a point of care device by minimally trained operators. This resonator development provides further utility to the dosimeter, and increases the usability of the dosimeter by non-expert operators in the intended use scenario. (authors)

21 CFR 872.5525 - Preformed tooth positioner.

Science.gov (United States)

2010-04-01

...) MEDICAL DEVICES DENTAL DEVICES Therapeutic Devices § 872.5525 Preformed tooth positioner. (a) Identification. A preformed tooth positioner is a plastic device that is an impression of a perfected bite...

Remineralising efficacy of tooth mousse plus (ACP CCPF) on radiated tooth

International Nuclear Information System (INIS)

Priya; Hegde, Mithra N.; Hegde, Nidarsh D.; Suchetha Kumari, N.; Sanjeev, Ganesh

2016-01-01

Dental complication is the common problem faced all over the world. Subjects with poor oral hygiene and patients undergoing radiotherapy for oral cancers are developing signs of decalcification of enamel, lesions and Caries. A well designed treatment is necessary to safeguard the tooth enamel surface before and after radiation, only then the caries on the enamel surface can be arrested by re-hardening it and ultimately converting them to the normal healthy condition. To determine the Annealing effect of radiated tooth by testing maximum micro hardness of the teeth before and after 30 days of radiation by the application of Remineralising agents. In our study, we collected 30 intact caries free human molar teeth and were sectioned mesio-distally

Parameters affecting tooth loss during periodontal maintenance in a Greek population.

Science.gov (United States)

Tsami, Alexandra; Pepelassi, Eudoxie; Kodovazenitis, George; Komboli, Mado

2009-09-01

Investigators have evaluated predictive parameters of tooth loss during the maintenance phase (MP). The authors conducted a retrospective study to evaluate the rate of tooth loss and to explore the parameters that affect tooth loss during MP in a Greek population. A periodontist administered periodontal treatment and maintenance care to 280 participants with severe periodontitis for a mean period +/- standard deviation of 10.84 +/- 2.13 years. The periodontist recorded the following parameters for each participant: oral hygiene index level, simplified gingival index level, clinical attachment level, probing depth measurements, initial tooth prognosis, smoking status, tooth loss during active periodontal treatment and MP, and compliance with suggested maintenance visits. The authors found that total tooth loss during active treatment (n = 1,427) was greater than during MP (n = 918) and was associated with the initial tooth prognosis, tooth type group, participants' compliance with suggested maintenance visits, smoking status and acceptability of the quality of tooth restorations. Most of the teeth extracted during maintenance had an initial guarded prognosis (n = 612). Participants whose compliance was erratic had a greater risk of undergoing tooth extraction than did participants whose compliance was complete. Participants' initial tooth prognosis, tooth type, compliance with suggested maintenance visits and smoking status affected tooth loss during MP. Initial guarded prognosis and erratic compliance increased the risk of undergoing tooth extraction during maintenance. Determining predictive parameters for disease progression and tooth loss provides critical information to clinicians so that they can develop and implement rational treatment planning.

Variables affecting orthodontic tooth movement with clear aligners.

Science.gov (United States)

Chisari, Justin R; McGorray, Susan P; Nair, Madhu; Wheeler, Timothy T

2014-04-01

In this study, we examined the impacts of age, sex, root length, bone levels, and bone quality on orthodontic tooth movement. Clear aligners were programmed to move 1 central incisor 1 mm over the course of 8 weeks. Thirty subjects, ages 19 to 64, were enrolled, and measurements were made on digital models (percentage of tooth movement goal achieved). Morphometric features and bone quality were assessed with cone-beam computed tomography. Data from this study were combined with data from 2 similar studies to increase the power for some analyses. The mean percentage of tooth movement goal achieved was 57% overall. Linear regression modeling indicated a cubic relationship between age and tooth movement, with a decreasing rate of movement from ages 18 to 35 years, a slightly increasing rate from ages 35 to 50, and a decreasing rate from ages 50 to 70. The final decreasing trend was not apparent for women. As would be expected, the correlation was significant between the percentage of the goal achieved and the cone-beam computed tomography superimposed linear measures of tooth movement. A significant negative correlation was found between tooth movement and the measurement apex to the center of rotation, but bone quality, as measured by fractal dimension, was not correlated with movement. The relationship between age and tooth movement is complex and might differ for male and female patients. Limited correlations with cone-beam computed tomography morphology and rate of tooth movement were detected. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Tooth resorption in cats: contribution of vitamin D and inflammation

NARCIS (Netherlands)

Vrieling, H.E.

2010-01-01

Tooth resorption in cats Tooth resorption affecting several teeth is a painful disease with a prevalence of up to 75% in household cats and is often accompanied by periodontitis. Tooth resorption is caused by an increased number and activity of tooth-resorbing odontoclasts, cells that share

Tooth Fracture Detection in Spiral Bevel Gears System by Harmonic Response Based on Finite Element Method

Directory of Open Access Journals (Sweden)

Yuan Chen

2017-01-01

Full Text Available Spiral bevel gears occupy several advantages such as high contact ratio, strong carrying capacity, and smooth operation, which become one of the most widely used components in high-speed stage of the aeronautical transmission system. Its dynamic characteristics are addressed by many scholars. However, spiral bevel gears, especially tooth fracture occurrence and monitoring, are not to be investigated, according to the limited published issues. Therefore, this paper establishes a three-dimensional model and finite element model of the Gleason spiral bevel gear pair. The model considers the effect of tooth root fracture on the system due to fatigue. Finite element method is used to compute the mesh generation, set the boundary condition, and carry out the dynamic load. The harmonic response spectra of the base under tooth fracture are calculated and the influence of main parameters on monitoring failure is investigated as well. The results show that the change of torque affects insignificantly the determination of whether or not the system has tooth fracture. The intermediate frequency interval (200 Hz–1000 Hz is the best interval to judge tooth fracture occurrence. The best fault test region is located in the working area where the system is going through meshing. The simulation calculation provides a theoretical reference for spiral bevel gear system test and fault diagnosis.

Tooth fractures in canine clinical practice

International Nuclear Information System (INIS)

Capik, I.; Ledecky, V.; Sevcik, A.

2001-01-01

Tooth fractures constitute a considerable fraction of all tooth diseases. Out of the 5,370 dogs treated during four years, 492 were presented with dental problems and 28.3 % of the latter were treated for tooth fractures. Canines were the most frequently affected teeth (38.8 %), followed by premolars (33.1 %), incisors (25.9 %), and molars (2.2 %), 55.4 % of the patients with canine and incisor fractures being large breed dogs. Fractures of premolars (mostly of 108, 208) were divided evenly irrespective of breed or body size. Nonsurgical endodontic treatment yielded good therapeutic results in most cases, but repeated treatment was necessary in some patients

Tooth cusp sharpness as a dietary correlate in great apes.

Science.gov (United States)

Berthaume, Michael A

2014-02-01

Mammalian molars have undergone heavy scrutiny to determine correlates between morphology and diet. Here, the relationship between one aspect of occlusal morphology, tooth cusp radius of curvature (RoC), and two broad dietary categories, folivory and frugivory, is analyzed in apes. The author hypothesizes that there is a relationship between tooth cusp RoC and diet, and that folivores have sharper teeth than frugivores, and further test the correlation between tooth cusp RoC and tooth cusp size. Eight measures of tooth cusp RoC (two RoCs per cusp) were taken from 53 M(2) s from four species and subspecies of frugivorous apes (Pongo pygmaeus, Pan troglodytes troglodytes, Pan troglodytes schweinfurthii, and Gorilla gorilla gorilla) and two subspecies of folivorous apes (Gorilla beringei beringei, and Gorilla beringei graueri). Phylogenetically corrected ANOVAs were run on the full dataset and several subsets of the full dataset, revealing that, when buccolingual RoCs are taken into account, tooth cusp RoCs can successfully differentiate folivores and frugivores. PCAs revealed that folivores consistently had duller teeth than frugivores. In addition, a weak, statistically significant positive correlation exists between tooth cusp size and tooth cusp RoC. The author hypothesizes differences in tooth cusp RoC are correlated with wear rates, where, per vertical unit of wear, duller cusps will have a longer length of exposed enamel ridge than sharper cusps. More data need to be gathered to determine if the correlation between tooth cusp RoC and tooth cusp size holds true when small primates are considered. Copyright © 2013 Wiley Periodicals, Inc.

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... Dentist Your Family's Oral Health About the AGD Dental care and oral health information you need from ... Menstrual Calendar for Tooth Extraction Learn what those dental words mean. The Life of a Tooth Home | ...

Is gingival recession a consequence of an orthodontic tooth size and/or tooth position discrepancy? "A paradigm shift".

Science.gov (United States)

Richman, Colin

2011-01-01

Gingival recession (GR) is a commonly observed dental lesion. The underlying etiology has not been clearly identified, although several theories have been suggested. Tooth crowding or tooth malalignment is also frequently observed, with both conditions appearing to be more prevalent in developed countries with heterogeneous populations. A total of 25 consecutively treated patients representing 72 teeth and demonstrating facial clinical GR of > 3 mm were examined clinically, photographically, and with 3-dimensional radiology using conebeam computed tomography. All examined teeth presented with normal interproximal probing depths and attachment levels (teeth demonstrating > 3 mm of GR presented with significantly prominent facial tooth contours and associated alveolar bone dehiscences. Most involved teeth presented with their root structures extending beyond the facial alveolar bony housing (fenestrations). This represents a discrepancy between tooth size and alveolar bone dimensions in the buccolingual, axial, and sagittal orientation. Fewer involved teeth were malpositioned toward the buccal aspect. Both conditions were associated with facial alveolar bone dehiscences and associated GR. This study suggests tooth volume and/or tooth position within the alveolar bony housing strongly correlate with GR. All nonperiodontitis-involved teeth with GR were associated with either wider teeth or facially aligned teeth. However, it is emphasized that all facially aligned teeth, or "larger" teeth, do not necessarily present with GR. Based on these findings, the radiographic-supporting bone index is proposed. This index should facilitate appropriate evaluation of the alveolar bone supporting the mucogingival complex, both on the facial and lingual aspect of teeth. Further investigations are needed to support these preliminary data.

Gastroesophageal Reflux Disease and Tooth Erosion

Directory of Open Access Journals (Sweden)

Sarbin Ranjitkar

2012-01-01

Full Text Available The increasing prevalence of gastroesophageal reflux disease (GERD in children and adults, and of “silent refluxers” in particular, increases the responsibility of dentists to be alert to this potentially severe condition when observing unexplained instances of tooth erosion. Although gastroesophageal reflux is a normal physiologic occurrence, excessive gastric and duodenal regurgitation combined with a decrease in normal protective mechanisms, including an adequate production of saliva, may result in many esophageal and extraesophageal adverse conditions. Sleep-related GERD is particularly insidious as the supine position enhances the proximal migration of gastric contents, and normal saliva production is much reduced. Gastric acid will displace saliva easily from tooth surfaces, and proteolytic pepsin will remove protective dental pellicle. Though increasing evidence of associations between GERD and tooth erosion has been shown in both animal and human studies, relatively few clinical studies have been carried out under controlled trial conditions. Suspicion of an endogenous source of acid being associated with observed tooth erosion requires medical referral and management of the patient as the primary method for its prevention and control.

Tooth positioners and their effects on treatment outcome.

Science.gov (United States)

Pravindevaprasad, A; Therese, Beena Agnes

2013-07-01

Malocclusion can also be corrected by means of clear removable appliances called as "tooth positioners" or "aligners". A tooth positioner is used to control settling and to minimize or eliminate relapse of the teeth after an orthodontic treatment. In this article, a complete review of the objectives, course of treatment, fabrication, and the materials used for fabrication of tooth positioners along with their importance and disadvantages were discussed. Tooth positioners did improve the overall orthodontic treatment outcome as quantified by the ABO (American Board of orthodontics) objective scoring method. But once the initial occlusal contact was achieved, the vertical movement of teeth was found to be inhibited.

Tooth-marked small theropod bone: an extremely rare trace

DEFF Research Database (Denmark)

Jacobsen, Aase Roland

2001-01-01

Tooth-marked dinosaur bones provide insight into feeding behaviours and biting strategies of theropod dinosaurs. The majority of theropod tooth marks reported to date have been found on herbivorous dinosaur bones, although some tyrannosaurid bones with tooth marks have also been reported. In 1988...

Association between Severity of Tooth Wear and Dentinal Hypersensitivity

Directory of Open Access Journals (Sweden)

Ashok Ayer

2016-11-01

Full Text Available Background & Objectives: Tooth wear (attrition, abrasion, erosion, and abfraction is perceived globally as ever increasing problem. Several outcome of the tooth wear are hypersensitivity, esthetic problems, functional impairment, annoyance to the patient, and fracture of the tooth. Among these, the measurable and more commonly reported outcome is hypersensitivity to stimuli. Although dentin hypersensitivity is a common clinical condition and is generally reported by the patient after experiencing a sharp, short pain caused by one of the several different external stimuli, it is often inadequately understood. None of the scientific literature available till date attempted to establish the relationship between tooth wear and dentin hypersensitivity which could be a key factor in monitoring those patients.  The aim of the study was to estimate the association between severity of teeth wear and sensitivity in the patients with reported dentinal hypersensitivity.Materials & Methods: Fifty patients with dentin hypersensitivity were investigated for tooth wear. Tooth wear measured using exact tooth wear index and level of sensitivity to stimuli was recorded using a numerical rating scale. Results: Enamel wear at cervical region of teeth showed a positive correlation (p=.010, similarly, dentin wear at cervical region of teeth showed positive correlation and significant association (p<.001 with dentinal hypersensitivity.Conclusion: The observation supports a significant association between severities of tooth surface wear and dentinal hypersensitivity.

Orientation and deformation of mineral crystals in tooth surfaces.

Science.gov (United States)

Fujisaki, Kazuhiro; Todoh, Masahiro; Niida, Atsushi; Shibuya, Ryota; Kitami, Shunsuke; Tadano, Shigeru

2012-06-01

Tooth enamel is the hardest material in the human body, and it is mainly composed of hydroxyapatite (HAp)-like mineral particles. As HAp has a hexagonal crystal structure, X-ray diffraction methods can be used to analyze the crystal structure of HAp in teeth. Here, the X-ray diffraction method was applied to the surface of tooth enamel to measure the orientation and strain of the HAp crystals. The c-axis of the hexagonal crystal structure of HAp was oriented to the surface perpendicular to the tooth enamel covering the tooth surface. Thus, the strain of HAp at the surface of teeth was measured by X-ray diffraction from the (004) lattice planes aligned along the c-axis. The X-ray strain measurements were conducted on tooth specimens with intact surfaces under loading. Highly accurate strain measurements of the surface of tooth specimens were performed by precise positioning of the X-ray irradiation area during loading. The strains of the (004) lattice plane were measured at several positions on the surface of the specimens under compression along the tooth axis. The strains were obtained as tensile strains at the labial side of incisor tooth specimens. In posterior teeth, the strains were different at different measurement positions, varying from tensile to compressive types. Copyright © 2012 Elsevier Ltd. All rights reserved.

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... Child First See a Dentist? The History of Dental Advances Why is Oral Health Important for Men? What is Baby Bottle Tooth Decay? Learn what those dental words mean. The Life of a Tooth Home | ...

Inhibitory effect of interferon-γ on experimental tooth movement in mice.

Science.gov (United States)

Kohara, Haruka; Kitaura, Hideki; Yoshimatsu, Masako; Fujimura, Yuji; Morita, Yukiko; Eguchi, Toshiko; Yoshida, Noriaki

2012-09-01

The aim of this study was to investigate the effects of interferon (IFN)-γ on experimental tooth movement in mice using a murine experimental tooth movement model. An Ni-Ti closed-coil spring was inserted between the upper-anterior alveolar bones and the upper-left first molars in mice. We evaluated the relationship between local Ifn-γ mRNA levels and orthodontic tooth movement. In other experiments, IFN-γ was injected adjacent to each first molar every other day during tooth movement. After 12 days, the amount of tooth movement was measured. Tartrate-resistant acid phosphatase (TRAP)-positive cells at the pressure side of each experimental tooth were counted as osteoclasts. Local Ifn-γ mRNA expression increased with orthodontic tooth movement. The number of TRAP-positive cells increased on the pressure side of the first molar. In contrast, the degree of tooth movement and the number of TRAP-positive cells on the pressure side in IFN-γ-injected mice were less than those of control mice. IFN-γ was induced in experimental tooth movement, and could inhibit mechanical force-loaded osteoclastogenesis and tooth movement. These results suggest that IFN-γ might be useful in controlling orthodontic tooth movement because of its inhibitory action on excessive osteoclastogenesis during this movement.

Tooth bleaching and young adults in Nigeria: knowledge, experiences and intention.

Science.gov (United States)

Azodo, C C; Ogbomo, A C; Agbor, M A

2012-12-01

To assess the knowledge, experiences and intention to have tooth bleaching among young adults studying in a Nigerian University. A cross-section of part-time undergraduate students of University of Benin, Benin City, Nigeria were studied in 2010 using a self-administered questionnaire. About three-quarters 289 (72.4%) of the respondents reported awareness of at least one cause of tooth discoloration. A total of 143 (35.8%) of the respondents have heard of tooth bleaching with main sources of information being friends/relatives, dentists and the internet. One-third 132 (33.1%) of the respondents correctly identified that the aim of tooth bleaching was to make the teeth whiter. The respondents that had correct knowledge about mechanism, duration and complications of tooth bleaching were 51 (12.8%), 25 (6.3%) and 35 (8.8%) respectively. The major perceived benefits of tooth bleaching reported by the respondents were self confidence boost 152 (38.1%) and improvement of one's beauty 107 (26.8%). Out of the 68 (17.0%) respondents that have attempted tooth bleaching, 36 (52.9%) used tooth whitening toothpaste. Out of the 151 (37.8%) respondents that expressed intention of having tooth bleaching procedure, 32 (21.2%) would pursue the course, no matter the cost. In the studied population, knowledge of tooth discoloration was high, awareness and experiences of tooth bleaching were low but significant number expressed intention of having tooth bleaching. It is important that dentists increase oral health information particularly tooth bleaching information accessibility to the young adult population to improve the knowledge and prevent adverse effects.

Tooth Decay Process: How to Reverse It and Avoid a Cavity

Science.gov (United States)

... Health Info Health Topics Tooth Decay Tooth decay (dental caries) is damage to a tooth that can happen ... Clinical Trials Show All Clinical Trials Data & Statistics Dental caries (tooth decay) remains the most prevalent chronic disease ...

Tooth polishing: The current status

Directory of Open Access Journals (Sweden)

Madhuri Alankar Sawai

2015-01-01

Full Text Available Healthy teeth and gums make a person feel confident and fit. As people go about their daily routines and with different eating and drinking habits, the tooth enamel turns yellowish or gets stained. Polishing traditionally has been associated with the prophylaxis procedure in most dental practices, which patients know and expect. However, with overzealous use of polishing procedure, there is wearing of the superficial tooth structure. This would lead to more accumulation of local deposits. Also, it takes a long time for the formation of the fluoride-rich layer of the tooth again. Hence, now-a-days, polishing is not advised as a part of routine oral prophylaxis procedure but is done selectively based on the patients′ need. The article here, gives an insight on the different aspects of the polishing process along with the different methods and agents used for the same.

Cracked tooth syndrome: A report of three cases.

Science.gov (United States)

Sadasiva, Kadandale; Ramalingam, Sathishmuthukumar; Rajaram, Krishnaraj; Meiyappan, Alagappan

2015-08-01

Cracked tooth syndrome (CTS), the term was coined by Cameron in 1964, which refers to an incomplete fracture of a vital posterior tooth extending to the dentin and occasionally into the pulp. CTS has always been a nightmare to the patient because of its unpredictable symptoms and a diagnostic dilemma for the dental practitioner due to its variable, bizarre clinical presentation. The treatment planning and management of CTS has also given problems and challenges the dentist as there is no specific treatment option. The management of CTS varies from one case to another or from one tooth to another in the same individual based on the severity of the symptoms and depth of tooth structure involved. After all, the prognosis of such tooth is still questionable and requires continuous evaluation. This article aims at presenting a series three cases of CTS with an overview on the clinical presentation, diagnosis and the different treatment options that varies from one case to another.

Combined periodontic-orthodonticendodontic interdisciplinary approach in the treatment of periodontally compromised tooth

OpenAIRE

Deepa, D; Mehta, D. S.; Puri, Viren K.; Shetty, Sadashiva

2010-01-01

Orthodontic treatment in adult patients is one of the most frequently encountered components involving multidisciplinary approaches. In the present report, a 28-year-old male patient was treated for localized chronic periodontitis with pocket formation, mobility, pathologic migration and malalignment of maxillary left lateral incisor tooth #22. The periodontal therapy included motivation, education and oral-hygiene instructions (O.H.I.), scaling and root planing and periodontal flap surgery. ...

Varanoid Tooth Eruption and Implantation Modes in a Late Cretaceous Mosasaur.

Science.gov (United States)

Liu, Min; Reed, David A; Cecchini, Giancarlo M; Lu, Xuanyu; Ganjawalla, Karan; Gonzales, Carol S; Monahan, Richard; Luan, Xianghong; Diekwisch, Thomas G H

2016-01-01

Erupting teeth are some of the oldest witnesses of developmental processes in the vertebrate fossil record and provide an important resource for vertebrate cladistics. Here, we have examined a mosasaur jaw fragment from central Texas using ultrathin ground section histology and 3D tomographic imaging to assess features critical for the cladistic placement of mosasaurs among varanoids vs. snakes: (i) the orientation of replacement teeth compared to the major tooth axis, (ii) the occurrence of resorption pits, and (iii) the mode of tooth implantation/attachment to the tooth bearing element (TBE). The replacement tooth studied here developed in an inclined position slightly distal of the deciduous parent tooth, similar to another varanoid squamate, the Gila monster Heloderma suspectum. Ground sections and tomographs also demonstrated that the replacement tooth attachment apparatus was entirely intact and that there was no evidence of mechanical deformation. Sections and tomographs further illustrated that the replacement tooth was located within a bony crypt and the inclination of the crypt matched the inclination of the replacement tooth. These preparations also revealed the presence of a resorption pit within the boundaries of the deciduous tooth that surrounded the developing replacement tooth. This finding suggests that developing mosasaur teeth developed within the walls of resorption pits similar to varanoid tooth germs and unlike developing snake teeth which are surrounded by fibrous connective tissue integuments. Finally, mosasaurs featured pseudo-thecodont tooth implantation with teeth anchored within a socket of mineralized tissue by means of a mineralized periodontal ligament. Together, these data indicate that the moderate inclination of the erupting mosasaur tooth studied here is neither a result of postmortem displacement nor a character representative of snakes, but rather a shared character between Mosasaurs and other varanoids such as Heloderma. In

Varanoid Tooth Eruption and Implantation Modes in a Late Cretaceous Mosasaur

Directory of Open Access Journals (Sweden)

Min eLiu

2016-05-01

Full Text Available Erupting teeth are some of the oldest witnesses of developmental processes in the vertebrate fossil record and provide an important resource for vertebrate cladistics. Here we have examined a mosasaur jaw fragment from central Texas using ultrathin ground section histology and 3D tomographic imaging to assess features critical for the cladistic placement of mosasaurs among varanoids versus snakes: (i the orientation of replacement teeth compared to the major tooth axis, (ii the occurrence of resorption pits, and (iii the mode of tooth implantation/attachment to the tooth bearing element. The replacement tooth studied here developed in an inclined position slightly distal of the deciduous parent tooth, similar to another varanoid squamate, the Gila monster Heloderma suspectum. Ground sections and tomographs also demonstrated that the replacement tooth attachment apparatus was entirely intact and that there was no evidence of mechanical deformation. Sections and tomographs further illustrated that the replacement tooth was located within a bony crypt and the inclination of the crypt matched the inclination of the replacement tooth. These preparations also revealed the presence of a resorption pit within the boundaries of the deciduous tooth that surrounded the developing replacement tooth. This finding suggests that developing mosasaur teeth developed within the walls of resorption pits similar to varanoid tooth germs and unlike developing snake teeth which are surrounded by fibrous connective tissue integuments. Finally, mosasaurs featured pseudo-thecodont tooth implantation with teeth anchored within a socket of mineralized tissue by means of a mineralized periodontal ligament. Together, these data indicate that the moderate inclination of the erupting mosasaur tooth studied here is neither a result of postmortem displacement nor a character representative of snakes, but rather a shared character between Mosasaurs and other varanoids such as

Factors associated with tooth loss and prosthodontic status among Sudanese adults.

Science.gov (United States)

Khalifa, Nadia; Allen, Patrick F; Abu-bakr, Neamat H; Abdel-Rahman, Manar E

2012-01-01

A study was conducted to determine the degree of tooth loss, factors influencing tooth loss, and the extent of prosthodontic rehabilitation in Sudanese adults (≥ 16 years old) attending outpatient clinics in Khartoum State. Pearson and multivariate analyses were used to examine the relationships between tooth loss and specific characteristics determined through interviews and clinical examinations. The mean number of missing teeth was 3.6 (SD, 4.9) and the prevalence of edentulism was 0.1%. The prevalence of tooth loss (missing at least one tooth) was 78%; 66.9% of tooth loss was due to caries, and 11.2% was attributable to other reasons. Prosthetic replacement of missing teeth was evident in 3%, whereas a need for prosthetic replacement was evident in 57%. Having teeth was associated with age, gender, and socioeconomic status; tooth loss due to caries was associated with age, tribe, frequency of tooth-brushing, and a low rate of dental consultation. Tooth loss due to other reasons was associated with age, tribe, education, periodontal pocketing, tobacco use, tooth wear, and prosthetic status. The results of the present study indicated that the major cause of tooth loss was dental caries, thus emphasizing the importance of a public prevention-based healthcare program. Replacement of missing teeth was uncommon in the study subjects, which may reflect lack of access to this type of oral healthcare.

Contaminated tooth brushes-potential threat to oral and general health

Directory of Open Access Journals (Sweden)

Rashmi Naik

2015-01-01

Full Text Available Background: Tooth brushing is most common method of maintaining oral hygiene. In removing plaque and other soft debris from the teeth, tooth brushes become contaminated with bacteria, blood, saliva and oral debris. These contaminated tooth brushes can be a source of infection. Aims and objectives: The aim of the present study was to evaluate the presence of microorganisms in the tooth brushes and to investigate the effect of disinfectants such as chlorhexidine gluconate, sodium hypochlorite and water to decontaminate them. Materials and Methods: Twenty-one children were asked to brush their teeth for 5 days with a tooth brush. The tooth brushes were put in Robertson′s Cooked Meat broth and were observed for growth of Streptococcal microorganisms. These tooth brushes were then placed in disinfectants such as 0.2% chlorhexidine gluconate (Group I, 1% sodium hypochlorite (Group II and water (Group III for 24 hrs and then cultured again. Reduction of growth of microorganisms was seen in Group I, Group II and remnants of growth seen in Group III. Conclusion: We conclude that the use of disinfectant for a tooth brush is a must for every individual at least at regular intervals.

Effect of Melamine Sponge on Tooth Stain Removal.

Science.gov (United States)

Otsuka, Takero; Kawata, Toshitsugu

2015-01-01

To investigate the stain removal ability of melamine sponge before aesthetic tooth whitening in extracted teeth. Melamine sponge of thickness 40 mm was compressed and the destruction of the partition wall structure during the compression process was examined under a stereoscopic microscope. An extracted human tooth was cleaned by normal polishing or with melamine sponge for 90 s. To evaluate the stain level, the tooth surfaces were photographed under a stereoscopic microscope at 0, 30, 60 and 90 s. The residual stained region was traced in a high-magnification photograph, and the stain intensity was presented as a change, relative to the intensity before the experiment (0 s). Mechanical cleaning by toothbrushing produced polishing scratches on the tooth surface, whereas use of the melamine sponge resulted in only minimal scratches. As the compression level increased, the stain-removing effect tended to become stronger. Melamine sponge can remove stains from the tooth surface more effectively and less invasively compared to a conventional toothbrush. As no new scratches are made on the tooth surface when using a melamine sponge brush, the risk of re-staining is reduced. Cleaning using a melamine sponge brush can be easily and effectively performed at home and in a dental office.

An automatic tooth preparation technique: A preliminary study

Science.gov (United States)

Yuan, Fusong; Wang, Yong; Zhang, Yaopeng; Sun, Yuchun; Wang, Dangxiao; Lyu, Peijun

2016-04-01

The aim of this study is to validate the feasibility and accuracy of a new automatic tooth preparation technique in dental healthcare. An automatic tooth preparation robotic device with three-dimensional motion planning software was developed, which controlled an ultra-short pulse laser (USPL) beam (wavelength 1,064 nm, pulse width 15 ps, output power 30 W, and repeat frequency rate 100 kHz) to complete the tooth preparation process. A total of 15 freshly extracted human intact first molars were collected and fixed into a phantom head, and the target preparation shapes of these molars were designed using customised computer-aided design (CAD) software. The accuracy of tooth preparation was evaluated using the Geomagic Studio and Imageware software, and the preparing time of each tooth was recorded. Compared with the target preparation shape, the average shape error of the 15 prepared molars was 0.05-0.17 mm, the preparation depth error of the occlusal surface was approximately 0.097 mm, and the error of the convergence angle was approximately 1.0°. The average preparation time was 17 minutes. These results validated the accuracy and feasibility of the automatic tooth preparation technique.

Periodontal profile classes predict periodontal disease progression and tooth loss.

Science.gov (United States)

Morelli, Thiago; Moss, Kevin L; Preisser, John S; Beck, James D; Divaris, Kimon; Wu, Di; Offenbacher, Steven

2018-02-01

Current periodontal disease taxonomies have limited utility for predicting disease progression and tooth loss; in fact, tooth loss itself can undermine precise person-level periodontal disease classifications. To overcome this limitation, the current group recently introduced a novel patient stratification system using latent class analyses of clinical parameters, including patterns of missing teeth. This investigation sought to determine the clinical utility of the Periodontal Profile Classes and Tooth Profile Classes (PPC/TPC) taxonomy for risk assessment, specifically for predicting periodontal disease progression and incident tooth loss. The analytic sample comprised 4,682 adult participants of two prospective cohort studies (Dental Atherosclerosis Risk in Communities Study and Piedmont Dental Study) with information on periodontal disease progression and incident tooth loss. The PPC/TPC taxonomy includes seven distinct PPCs (person-level disease pattern and severity) and seven TPCs (tooth-level disease). Logistic regression modeling was used to estimate relative risks (RR) and 95% confidence intervals (CI) for the association of these latent classes with disease progression and incident tooth loss, adjusting for examination center, race, sex, age, diabetes, and smoking. To obtain personalized outcome propensities, risk estimates associated with each participant's PPC and TPC were combined into person-level composite risk scores (Index of Periodontal Risk [IPR]). Individuals in two PPCs (PPC-G: Severe Disease and PPC-D: Tooth Loss) had the highest tooth loss risk (RR = 3.6; 95% CI = 2.6 to 5.0 and RR = 3.8; 95% CI = 2.9 to 5.1, respectively). PPC-G also had the highest risk for periodontitis progression (RR = 5.7; 95% CI = 2.2 to 14.7). Personalized IPR scores were positively associated with both periodontitis progression and tooth loss. These findings, upon additional validation, suggest that the periodontal/tooth profile classes and the derived

Safety issues of tooth whitening using peroxide-based materials.

Science.gov (United States)

Li, Y; Greenwall, L

2013-07-01

In-office tooth whitening using hydrogen peroxide (H₂O₂) has been practised in dentistry without significant safety concerns for more than a century. While few disputes exist regarding the efficacy of peroxide-based at-home whitening since its first introduction in 1989, its safety has been the cause of controversy and concern. This article reviews and discusses safety issues of tooth whitening using peroxide-based materials, including biological properties and toxicology of H₂O₂, use of chlorine dioxide, safety studies on tooth whitening, and clinical considerations of its use. Data accumulated during the last two decades demonstrate that, when used properly, peroxide-based tooth whitening is safe and effective. The most commonly seen side effects are tooth sensitivity and gingival irritation, which are usually mild to moderate and transient. So far there is no evidence of significant health risks associated with tooth whitening; however, potential adverse effects can occur with inappropriate application, abuse, or the use of inappropriate whitening products. With the knowledge on peroxide-based whitening materials and the recognition of potential adverse effects associated with the procedure, dental professionals are able to formulate an effective and safe tooth whitening regimen for individual patients to achieve maximal benefits while minimising potential risks.

Effect of light energy on peroxide tooth bleaching.

Science.gov (United States)

Luk, Karen; Tam, Laura; Hubert, Manfred

2004-02-01

Light-activated bleaching is a method of tooth whitening. The authors conducted a study to compare the whitening effects and tooth temperature changes induced by various combinations of peroxide bleaches and light sources. The authors randomly assigned 250 extracted human teeth halves into experimental groups (n = 10). A placebo gel (control), a 35 percent hydrogen peroxide or a 10 percent carbamide peroxide bleach was placed on the tooth surface and was irradiated with no light (control); a halogen curing light; an infrared, or IR, light; an argon laser; or a carbon dioxide, or CO2, laser. Color changes were evaluated immediately, one day and one week after treatment using a value-oriented shade guide and an electronic dental color analyzer. The outer enamel and inner dentin surface temperatures were monitored before and immediately after each 30-second application of light using a thermocouple thermometer. Color and temperature changes were significantly affected by an interaction of the bleach and light variables. The application of lights significantly improved the whitening efficacy of some bleach materials, but it caused significant temperature increases in the outer and inner tooth surfaces. The IR and CO2 laser lights caused the highest tooth temperature increases. Dentists performing an in-office bleaching technique with the use of an additional light source to accelerate tooth whitening should consider the specific bleaching agent being used, as well as the potential risks of heating teeth. A specific combination of bleach and light that demonstrates good color change and little temperature rise should be selected for in-office tooth bleaching.

Advances and perspectives in tooth tissue engineering.

Science.gov (United States)

Monteiro, Nelson; Yelick, Pamela C

2017-09-01

Bio-engineered teeth that can grow and remodel in a manner similar to that of natural teeth have the potential to serve as permanent replacements to the currently used prosthetic teeth, such as dental implants. A major challenge in designing functional bio-engineered teeth is to mimic both the structural and anisotropic mechanical characteristics of the native tooth. Therefore, the field of dental and whole tooth regeneration has advanced towards the molecular and nanoscale design of bio-active, biomimetic systems, using biomaterials, drug delivery systems and stem cells. The focus of this review is to discuss recent advances in tooth tissue engineering, using biomimetic scaffolds that provide proper architectural cues, exhibit the capacity to support dental stem cell proliferation and differentiation and sequester and release bio-active agents, such as growth factors and nucleic acids, in a spatiotemporal controlled manner. Although many in vitro and in vivo studies on tooth regeneration appear promising, before tooth tissue engineering becomes a reality for humans, additional research is needed to perfect methods that use adult human dental stem cells, as opposed to embryonic dental stem cells, and to devise the means to generate bio-engineered teeth of predetermined size and shape. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Direct Resin Composite Restoration of Maxillary Central Incisors with Fractured Tooth Fragment Reattachment: Case Report.

Science.gov (United States)

Szmidt, Monika; Górski, Maciej; Barczak, Katarzyna; Buczkowska-Radlińska, Jadwiga

This article presents a clinical protocol to reconstruct two accidentally damaged maxillary central incisors using composite resin material and a fractured tooth component. A patient was referred to the clinic with fracture of the two maxillary central incisors. Clinical examination revealed that both teeth were fractured in the middle third of the crown and that the fractures involved enamel and dentin with no pulp exposure. The patient had also suffered a lower lip laceration. When the lip was evaluated, a fractured fragment of the maxillary right central incisor was found inside the wound. The missing part of the tooth was replaced via adhesive attachment. Due to the damage of the fractured part of the maxillary left central incisor, direct composite restoration of this tooth was performed. With the advent of adhesive dentistry, the process of fragment reattachment has become simplified and more reliable. This procedure provides improved function, is faster to perform, and provides long-lasting effects, indicating that reattachment of a coronal fragment is a realistic alternative to placement of conventional resin composite restorations.

Autotransplantation donor tooth site harvesting using piezosurgery.

Science.gov (United States)

Ylikontiola, Leena P; Sándor, George K

2016-01-01

The harvesting of a tooth as a candidate for tooth autotransplantation requires that the delicate dental tissues around the tooth be minimally traumatized. This is especially so for the periradicular tissues of the tooth root and the follicular tissues surrounding the crown. The aim of this report is to describe the use of piezosurgery as an attempt at morbidity reduction in the harvesting of teeth for autotransplantation. A piezosurgical handpiece and its selection of tips were easily adapted to allow the harvesting and delivery of teeth for autotransplantation purposes. Twenty premolar teeth were harvested using a piezosurgical device. The harvested teeth were subsequently successfully autotransplanted. All twenty teeth healed in a satisfactory manner without excessive mobility or ankyloses. Piezosurgery avoids some of the traumatic aspects of harvesting teeth and removing bone which are associated with thermal damage from the use of conventional rotary instruments or saws. Piezosurgery can be adapted to facilitate the predictable harvesting of teeth for autotransplantation purposes.

Innovative Design and Performance Evaluation of Bionic Imprinting Toothed Wheel.

Science.gov (United States)

Zhang, Zhihong; Wang, Xiaoyang; Tong, Jin; Stephen, Carr

2018-01-01

A highly efficient soil-burrowing dung beetle possesses an intricate outer contour curve on its foreleg end-tooth. This study was carried out based on evidence that this special outer contour curve has the potential of reducing soil penetration resistance and could enhance soil-burrowing efficiency. A toothed wheel is a typical agricultural implement for soil imprinting, to increase its working efficiency; the approach of the bionic geometrical structure was utilized to optimize the innovative shape of imprinting toothed wheel. Characteristics in the dung beetle's foreleg end-tooth were extracted and studied by the edge detection technique. Then, this special outer contour curve was modeled by a nine-order polynomial function and used for the innovative design of imprinting the tooth's cutting edge. Both the conventional and bionic teeth were manufactured, and traction tests in a soil bin were conducted. Taking required draft force and volume of imprinted microbasin as the evaluating indexes, operating efficiency and quality of different toothed wheels were compared and investigated. Results indicate that compared with the conventional toothed wheel, a bionic toothed wheel possesses a better forward resistance reduction property against soil and, meanwhile, can enhance the quality of soil imprinting by increasing the volume of the created micro-basin.

Tooth brushing among 11- to 15-year-olds in Denmark

DEFF Research Database (Denmark)

Bast, L. S.; Holstein, B. E.; Nordahl, Helene

2015-01-01

brushing. Results: 10,607 respondents: a response rate of 88.3%. Boys of lower social class had higher odds ratio (OR) of infrequent tooth brushing than girls: 1.98 (95% confidence interval 1.62-2.41) vs 1.80 (1.53-2.24). Immigrants and descendants had higher odds compared to adolescents of Danish origin......Objective: Regular tooth brushing in adolescence predicts stable tooth brushing habits later in life. Differences in tooth brushing habits by ethnic background and socioeconomic position have been suggested. We investigated migration status and social class in relation to infrequent tooth brushing...... both separately and combined. Methods: The study population was 11-15 year-olds chosen from a clustered random sample of schools. Univariate and multivariate logistic regression analyses estimated the separate and combined effects of migration status and social class on less than twice daily tooth...

Stem cells for tooth engineering

Directory of Open Access Journals (Sweden)

G Bluteau

2008-07-01

Full Text Available Tooth development results from sequential and reciprocal interactions between the oral epithelium and the underlying neural crest-derived mesenchyme. The generation of dental structures and/or entire teeth in the laboratory depends upon the manipulation of stem cells and requires a synergy of all cellular and molecular events that finally lead to the formation of tooth-specific hard tissues, dentin and enamel. Although mesenchymal stem cells from different origins have been extensively studied in their capacity to form dentin in vitro, information is not yet available concerning the use of epithelial stem cells. The odontogenic potential resides in the oral epithelium and thus epithelial stem cells are necessary for both the initiation of tooth formation and enamel matrix production. This review focuses on the different sources of stem cells that have been used for making teeth in vitro and their relative efficiency. Embryonic, post-natal or even adult stem cells were assessed and proved to possess an enormous regenerative potential, but their application in dental practice is still problematic and limited due to various parameters that are not yet under control such as the high risk of rejection, cell behaviour, long tooth eruption period, appropriate crown morphology and suitable colour. Nevertheless, the development of biological approaches for dental reconstruction using stem cells is promising and remains one of the greatest challenges in the dental field for the years to come.

Tooth color: effects on judgments of attractiveness and age.

Science.gov (United States)

Grosofsky, Alexis; Adkins, Sarah; Bastholm, Robert; Meyer, Leif; Krueger, Lisa; Meyer, Joshua; Torma, Peter

2003-02-01

Tooth whitening has become a very popular procedure. Advertisements for whitening products imply that whiter teeth are more attractive than yellower teeth. We tested this idea empirically by manipulating the tooth color of pictures of male and female targets. Participants' ratings of attractiveness were not influenced by tooth color. Exp. 2 yielded a negative correlation between attractiveness and age ratings: targets judged to be older were rated as less attractive. Unless whiter teeth help in some other way, e.g., improved self-esteem or confidence, it seems that tooth whitening procedures or products are not associated with increased attractiveness to others.

Side effects of external tooth bleaching

DEFF Research Database (Denmark)

Bruzell, E.M.; Pallesen, Ulla; Thoresen, N.R.

2013-01-01

Objective The study was performed to assess the risk of at-home and in-office bleaching procedures, and to recognise potential predictors for side effects. Design Multi-centre, questionnaire-based prospective study with follow-ups at around 14 days and around one year post-treatment. Setting...... General practices and university clinics during the years 2007‑2009 in Scandinavia. Subjects Patients with tooth bleaching as part of the treatment plan. Results The prevalence of experienced tooth sensitivity at first follow-up was independent of bleaching procedure (at-home = 50.3% [n = 143]; in...... attributed to the bleaching treatment in the at-home and in-office groups, respectively. Predictors for side effects were tooth sensitivity, surface loss and gingivitis when observed at inclusion. Treatment-related predictors were bleaching concentration and contact between tray and gingiva. Conclusions...

Clinical evaluation of a newly designed orthodontic tooth brush - A clinical study

Directory of Open Access Journals (Sweden)

C S Saimbi

2009-01-01

In this study, the newly designed orthodontic tooth brush is compared with an ordinary tooth brush. Results of this study show that the newly designed orthodontic tooth brush is superior in its cleaning efficiency as compared to the ordinary tooth brush. The results show that plaque removing capacity of orthodontic tooth brush is nearly 95-99%.

The role of microbial iron reduction in the formation of Proterozoic molar tooth structures

Science.gov (United States)

Hodgskiss, Malcolm S. W.; Kunzmann, Marcus; Poirier, André; Halverson, Galen P.

2018-01-01

Molar tooth structures are poorly understood early diagenetic, microspar-filled voids in clay-rich carbonate sediments. They are a common structure in sedimentary successions dating from 2600-720 Ma, but do not occur in rocks older or younger, with the exception of two isolated Ediacaran occurrences. Despite being locally volumetrically significant in carbonate rocks of this age, their formation and disappearance in the geological record remain enigmatic. Here we present iron isotope data, supported by carbon and oxygen isotopes, major and minor element concentrations, and total organic carbon and sulphur contents for 87 samples from units in ten different basins spanning ca. 1900-635 Ma. The iron isotope composition of molar tooth structures is almost always lighter (modal depletion of 2‰) than the carbonate or residue components in the host sediment. We interpret the isotopically light iron in molar tooth structures to have been produced by dissimilatory iron reduction utilising Fe-rich smectites and Fe-oxyhydroxides in the upper sediment column. The microbial conversion of smectite to illite results in a volume reduction of clay minerals (∼30%) while simultaneously increasing pore water alkalinity. When coupled with wave loading, this biogeochemical process is a viable mechanism to produce voids and subsequently precipitate carbonate minerals. The disappearance of molar tooth structures in the mid-Neoproterozoic is likely linked to a combination of a decrease in smectite abundance, a decline in the marine DIC reservoir, and an increase in the concentration of O2 in shallow seawater.

Power Consumption Optimization in Tooth Gears Processing

Science.gov (United States)

Kanatnikov, N.; Harlamov, G.; Kanatnikova, P.; Pashmentova, A.

2018-01-01

The paper reviews the issue of optimization of technological process of tooth gears production of the power consumption criteria. The authors dwell on the indices used for cutting process estimation by the consumed energy criteria and their applicability in the analysis of the toothed wheel production process. The inventors proposed a method for optimization of power consumptions based on the spatial modeling of cutting pattern. The article is aimed at solving the problem of effective source management in order to achieve economical and ecological effect during the mechanical processing of toothed gears. The research was supported by Russian Science Foundation (project No. 17-79-10316).

Addressing Tooth Decay in Head Start Children

Science.gov (United States)

Knowlden, Adam P.; Hill, Lawrence F.; Alles-White, Monica L.; Cottrell, Randall R.

2012-01-01

Tooth decay is the most prevalent chronic disease of childhood. Oral health education and dental services are crucial to reducing the number of children afflicted with dental cavities. Due to limited access to preventative care, Head Start children are particularly vulnerable to tooth decay. This article outlines practical implications of a…

Relationship between natural tooth shade and skin colour.

Science.gov (United States)

Nourbakhsh, M; Mousavinejad, N; Adli, A R; Harati, M

2013-06-01

The purpose of this study was to assess the correlation of skin colour and tooth shade. One hundred and twenty six individuals aging between 18 to 25 years participated in this study. Colour of the maxillary central incisors was examined by VITA easy shade. Tooth shades were assigned to four ordinal values. Nivea Beauty Protect Foundation shade sample was used as a guide to assess facial skin colour Shin colours were also assigned to four ordinal values. Spearman test revealed that there was a significant relationship between tooth shade and skin colour Total co-relation factor was 51.6% (p men (p <0 .01). The highest tooth shade prevalence belonged to the second group and the highest skin colour prevalence was also in the second skin colour group.

Power loss analysis in altered tooth-sum spur gearing

Directory of Open Access Journals (Sweden)

Sachidananda H. K.

2018-01-01

Full Text Available The main cause of power loss or dissipation of heat in case of meshed gears is due to friction existing between gear tooth mesh and is a major concern in low rotational speed gears, whereas in case of high operating speed the power loss taking place due to compression of air-lubricant mixture (churning losses and windage losses due to aerodynamic trial of air lubricant mixture which controls the total efficiency needs to be considered. Therefore, in order to improve mechanical efficiency it is necessary for gear designer during gear tooth optimization to consider these energy losses. In this research paper the power loss analysis for a tooth-sum of 100 altered by ±4% operating between a specified center distance is considered. The results show that negative altered tooth-sum gearing performs better as compared to standard and positive altered tooth-sum gearing.

Infrared light sensor applied to early detection of tooth decay

Science.gov (United States)

Benjumea, Eberto; Espitia, José; Díaz, Leonardo; Torres, Cesar

2017-08-01

The approach dentistry to dental care is gradually shifting to a model focused on early detection and oral-disease prevention; one of the most important methods of prevention of tooth decay is opportune diagnosis of decay and reconstruction. The present study aimed to introduce a procedure for early diagnosis of tooth decay and to compare result of experiment of this method with other common treatments. In this setup, a laser emitting infrared light is injected in core of one bifurcated fiber-optic and conduced to tooth surface and with the same bifurcated fiber the radiation reflected for the same tooth is collected and them conduced to surface of sensor that measures thermal and light frequencies to detect early signs of decay below a tooth surface, where demineralization is difficult to spot with x-ray technology. This device will can be used to diagnose tooth decay without any chemicals and rays such as high power lasers or X-rays.

21 CFR 872.3750 - Bracket adhesive resin and tooth conditioner.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Bracket adhesive resin and tooth conditioner. 872... SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3750 Bracket adhesive resin and tooth conditioner. (a) Identification. A bracket adhesive resin and tooth conditioner is a device...

Visualization of Tooth for Non-Destructive Evaluation from CT Images

Energy Technology Data Exchange (ETDEWEB)

Gao, Hui; Chae, Ok Sam [Kyung Hee University, Seoul (Korea, Republic of)

2009-06-15

This paper reports an effort to develop 3D tooth visualization system from CT sequence images as a part of the non-destructive evaluation suitable for the simulation of endodontics, orthodontics and other dental treatments. We focus on the segmentation and visualization for the individual tooth. In dental CT images teeth are touching the adjacent teeth or surrounded by the alveolar bones with similar intensity. We propose an improved level set method with shape prior to separate a tooth from other teeth as well as the alveolar bones. Reconstructed 3D model of individual tooth based on the segmentation results indicates that our technique is a very conducive tool for tooth visualization, evaluation and diagnosis. Some comparative visualization results validate the non-destructive function of our method.

Angulation change of the third molar tooth in orthodontic treatment

Directory of Open Access Journals (Sweden)

Ardiansyah S. Pawinru

2017-04-01

Full Text Available Objective : Impaction of the third molar tooth mandibular is often found in patients with orthodontic treatment. In orthodontic treatment, extraction cases of impaction of the third molar tooth are usually performed, but the patients often refuse this extraction. Extraction of premolar has a good effect on the third molar mandibular angulation during treatment. Material and Methods : This study is a retrospective clinical study with descriptive analytic to find out the effect of the first mandibular premolar tooth extraction to angulation change of the third molar mandibular in orthodontic treatment with a standard edgewise method. Angulation change was performed by comparing the third molar mandibular angulation before and after orthodontic treatment with panoramic radiographs. Angulation of the third molar tooth mandibular was calculated from the angle formed between the long axis of the tooth with the reference line infraorbita. Results : The sample comprised 60 of impacted mandibular third molar region of the left and right regions of 30 patients who had been treated declared cured in clinic of orthodontic specialist of Dentistry Faculty Padjadjaran University. The sample was divided into three (3 groups of patients before treatment angulation of the third molar tooth mandibular under 300, 300 to 600 and above 60o, then measured change of angulation and observed whether it increased, fixed or decreased. Results were analyzed by T- test and Wilcoxon test showed that there was a significant change in angulation of the third molar mandibular in orthodontic treatment with the first premolar tooth mandibular extraction. Conclusion : This study is that the first premolar tooth mandibular extraction affects the angulation of the third molar tooth mandibular after orthodontic treatment.

Platelet-rich fibrin-mediated revitalization of immature necrotic tooth

Directory of Open Access Journals (Sweden)

Navin Mishra

2013-01-01

Full Text Available Contemporary studies have shown that the regeneration of tissues and root elongation is possible in necrotic immature permanent teeth. The purpose of this case report is to add a new vista in regenerative endodontic therapy by using platelet rich fibrin for revitalization of immature non vital tooth. An 11year old boy with the history of trauma was diagnosed with the pulpal necrosis and symptomatic apical periodontitis in tooth #21. Intra oral periapical radiograph showed open apex and associated immature supernumerary tooth with respect to tooth #21. Access preparation and minimal instrumentation was done to remove necrotic debris under copious irrigation with 2.5% sodium hypochlorite. Triple antibiotic paste was packed in the canal for four weeks. During second visit, 5 mL of whole blood was drawn from the medial cubital vein of the patient and blood was then subjected to centrifugation at 2400 rpm for 12 minutes for the preparation of Platelet rich fibrin (PRF utilizing Choukroun′s method. Triple antibiotic paste was removed and canal was dried. PRF clot was pushed to the apical region of tooth #21 using hand pluggers. Three milimetres of Mineral trioxide (MTA was placed in cervical part of the root canal and permanent restoration was done three days later. Clinical examination at 6 and 12 months revealed no sensitivity to percussion and palpation in tooth #21and it responded positively to both electric pulp and cold tests. Radiographic examination showed resolution of periapical rarefaction, further root development and apical closure of the tooth #21 and its associated supernumerary tooth. On the basis of successful outcome of the present case it can be stated that PRF clot may serve as a scaffold for regeneration of necrotic immature teeth.

The Importance of Tooth Decay Prevention in Children under Three

Science.gov (United States)

Milgrom, Peter; Huebner, Colleen; Chi, Donald

2010-01-01

Tooth decay and tooth loss was once the norm but public health interventions have led to major improvements for most people. Nevertheless, not all children have benefited. Dental disease in young children is unacceptably high. Tooth decay is preventable. Early childhood educators are often the first to notice the problem. Professional…

Promoting positive health behaviours--'tooth worm' phenomenon and its implications.

Science.gov (United States)

Gao, X L; Hsu, C Y S; Xu, Y C; Loh, T; Koh, D; Hwarng, H B

2012-03-01

'Tooth worm' is a traditional belief about the pathogen of dental caries (tooth decay). Nevertheless, in our previous study, parental 'tooth worm' belief was linked to a reduced caries risk of their children. This study aimed to further characterize the impact of parental 'tooth worm' belief on their children's caries experience and its psychobehavioural mechanisms. analytic observational study. Thirteen randomly selected kindergartens in Singapore. 1,782 preschoolers aged 3-6 years. Each child received an oral examination and microbiological tests. Parents completed a self-administered questionnaire on their socio-demographic background, oral health knowledge/attitude and child's oral health habits. Multivariate analysis confirmed a reduced chance of 'high caries rate' (number of affected teeth > 2) among children whose parents held the 'tooth worm' belief (Odds Ratio = 0.41; 95% Confidence Interval = 0.19-0.89). With such perception among parents, children brushed their teeth more frequently (p = 0.042). Since no difference in oral hygiene was observed, the health benefit of the "tooth worm" perception may be acquired through the delivery of fluoride (an agent with proven anti-caries effect) during frequent toothbrushing episodes. This study revealed a 'tooth worm' phenomenon, indicating that parental 'tooth worm' belief is associated with early establishment of regular toothbrushing habit and reduction of dental caries in children. This phenomenon and its psychobehavioural mechanisms, enriching our understanding of oral health behaviours, have implications for effective health education.

Orthodontic Tooth Movement with Clear Aligners

OpenAIRE

Drake, Carl T.; McGorray, Susan P.; Dolce, Calogero; Nair, Madhu; Wheeler, Timothy T.

2012-01-01

Clear aligners provide a convenient model to measure orthodontic tooth movement (OTM). We examined the role of in vivo aligner material fatigue and subject-specific factors in tooth movement. Fifteen subjects seeking orthodontic treatment at the University of Florida were enrolled. Results were compared with data previously collected from 37 subjects enrolled in a similar protocol. Subjects were followed prospectively for eight weeks. An upper central incisor was programmed to move 0.5 mm. ev...

Drugs influencing orthodontic tooth movement: An overall review

Directory of Open Access Journals (Sweden)

Kamatchi Diravidamani

2012-01-01

Full Text Available Orthodontic treatment is based on the premise that when force is delivered to a tooth and thereby transmitted to the adjacent investing tissues, certain mechanical, chemical, and cellular events take place within these tissues, which allow for structural alterations and contribute to the movement of that tooth. Molecules present in drugs and nutrients consumed regularly by patients can reach the mechanically stressed paradental tissues through the circulation and interact with local target cells. The combined effect of mechanical forces and one or more of these agents may be inhibitory, additive, or synergistic. Current orthodontic research aims to develop methods of increasing the tissue concentration of molecules promoting tooth movement, while simultaneously decreasing the concentration of unwanted elements which can produce harmful side effects. This article discusses in detail the various possible drugs that can bring about alterations in the desired orthodontic tooth movement.

Replacing a Missing Tooth

Science.gov (United States)

... lateral incisor. This may be accomplished by adding plastic or porcelain filling material or a porcelain crown ... This type of bridge requires much less tooth reduction of adjacent teeth, and there is no danger ...

[Esthetic analysis on immediate single-tooth implant restoration in anterior maxilla].

Science.gov (United States)

Li, Shao-wei; Wang, Guo-shi; Sha, Yan-zhi

2015-10-01

To evaluate the esthetic outcomes of immediate single-tooth implant restoration in anterior maxilla with the pink esthetic score (PES). Nine patients were treated with 9 Straumann implants by immediate single-tooth implant restoration in anterior maxilla. Assessment of PES after crown placement at 1 week (baseline) and 6 months after implantation was conducted. Statistical analysis was performed using SPSS 16.0 software package. Nine implants achieved a retention rate of 100%. PES for single-tooth implant was 10.33 ± 1.50 at 1 week and 11.44 ± 0.88 at 6 months after crown placement. The difference was significant(P=0.021). This study indicates that immediate single-tooth implant restoration in anterior maxilla is predictable. Immediate single-tooth implantation can result in good clinical esthetic results in most patients with single-tooth missing in anterior maxilla.

Tooth eruption and browridge formation.

Science.gov (United States)

Russell, M D

1982-05-01

One of the most reasonable hypotheses regarding the functional significance of the browridge is that the supraorbital torus forms in response to masticatory stress during development. Oyen, Walker, and Rice (1979) have recently proposed a model that tests this hypothesis: if browridges are functionally related to masticatory stresses on the cranial vault, then changes in the biomechanics of the masticatory system ought to be reflected by changes in the browridge. To test their model they attempted to relate biomechanical discontinuities resulting from tooth eruption to episodes of bone deposition on the supraorbital tori of a developmental series of dry Papio crania. This paper reports on a parallel test of the model on a cross-sectional sample of Australian Aboriginal juvenile crania. This sample showed no relation between tooth eruption and the supraorbital surface morphology thought to be indicative of active bone deposition. It is also demonstrated that no significant relationship between tooth eruption and episodes of bone deposition is shown by the Papio sample. It is concluded that the use of small cross-sectional samples of dry crania does not provide a valid test of the model.

Esthetic enhancement of a traumatized anterior tooth with a combination of forced eruption and tooth alignment: a case report

Science.gov (United States)

Kang, So-Hee; Jin, Myoung-Uk; Kim, Sung-Kyo

2016-01-01

Exposing sound structure of a subgingivally fractured tooth using orthodontic extrusion is considered to be a conservative way to re-establish biologic width without sacrificing esthetics or jeopardizing periodontal support of neighboring teeth. When a misaligned tooth is traumatically involved, a more comprehensive approach combining tooth extrusion and re-alignment may be necessary for a successful restorative outcome. This case report describes a successful esthetic management of a patient with complicated crown-root fracture on the maxillary right central incisor and pre-existing malocclusion in the maxillary anterior region. Forced eruption along with re-alignment of teeth by orthodontic movement seems to allow re-positioning of the fracture line to a favorable position and correction of crowding, providing a better esthetic result. PMID:27508163

ISS protocol for EPR tooth dosimetry

International Nuclear Information System (INIS)

Onori, S.; Aragno, D.; Fattibene, P.; Petetti, E.; Pressello, M.C.

2000-01-01

The accuracy in Electron Paramagnetic Resonance (EPR) dose reconstruction with tooth enamel is affected by sample preparation, dosimetric signal amplitude evaluation and unknown dose estimate. Worldwide efforts in the field of EPR dose reconstruction with tooth enamel are focused on the optimization of the three mentioned steps in dose assessment. In the present work, the protocol implemented at ISS in the framework of the European Community Nuclear Fission Safety project 'Dose Reconstruction' is presented. A combined mechanical-chemical procedure for ground enamel sample preparation is used. The signal intensity evaluation is carried out with powder spectra simulation program. Finally, the unknown dose is evaluated individually for each sample with the additive dose method. The unknown dose is obtained by subtracting a mean native dose from the back-extrapolated dose. As an example of the capability of the ISS protocol in unknown dose evaluation, the results obtained in the framework of the 2nd International Intercomparison on EPR tooth enamel dosimetry are reported

Using a Novel Absolute Ontogenetic Age Determination Technique to Calculate the Timing of Tooth Eruption in the Saber-Toothed Cat, Smilodon fatalis.

Directory of Open Access Journals (Sweden)

M Aleksander Wysocki

Full Text Available Despite the superb fossil record of the saber-toothed cat, Smilodon fatalis, ontogenetic age determination for this and other ancient species remains a challenge. The present study utilizes a new technique, a combination of data from stable oxygen isotope analyses and micro-computed tomography, to establish the eruption rate for the permanent upper canines in Smilodon fatalis. The results imply an eruption rate of 6.0 millimeters per month, which is similar to a previously published average enamel growth rate of the S. fatalis upper canines (5.8 millimeters per month. Utilizing the upper canine growth rate, the upper canine eruption rate, and a previously published tooth replacement sequence, this study calculates absolute ontogenetic age ranges of tooth development and eruption in S. fatalis. The timing of tooth eruption is compared between S. fatalis and several extant conical-toothed felids, such as the African lion (Panthera leo. Results suggest that the permanent dentition of S. fatalis, except for the upper canines, was fully erupted by 14 to 22 months, and that the upper canines finished erupting at about 34 to 41 months. Based on these developmental age calculations, S. fatalis individuals less than 4 to 7 months of age were not typically preserved at Rancho La Brea. On the whole, S. fatalis appears to have had delayed dental development compared to dental development in similar-sized extant felids. This technique for absolute ontogenetic age determination can be replicated in other ancient species, including non-saber-toothed taxa, as long as the timing of growth initiation and growth rate can be determined for a specific feature, such as a tooth, and that growth period overlaps with the development of the other features under investigation.

Using a Novel Absolute Ontogenetic Age Determination Technique to Calculate the Timing of Tooth Eruption in the Saber-Toothed Cat, Smilodon fatalis.

Science.gov (United States)

Wysocki, M Aleksander; Feranec, Robert S; Tseng, Zhijie Jack; Bjornsson, Christopher S

2015-01-01

Despite the superb fossil record of the saber-toothed cat, Smilodon fatalis, ontogenetic age determination for this and other ancient species remains a challenge. The present study utilizes a new technique, a combination of data from stable oxygen isotope analyses and micro-computed tomography, to establish the eruption rate for the permanent upper canines in Smilodon fatalis. The results imply an eruption rate of 6.0 millimeters per month, which is similar to a previously published average enamel growth rate of the S. fatalis upper canines (5.8 millimeters per month). Utilizing the upper canine growth rate, the upper canine eruption rate, and a previously published tooth replacement sequence, this study calculates absolute ontogenetic age ranges of tooth development and eruption in S. fatalis. The timing of tooth eruption is compared between S. fatalis and several extant conical-toothed felids, such as the African lion (Panthera leo). Results suggest that the permanent dentition of S. fatalis, except for the upper canines, was fully erupted by 14 to 22 months, and that the upper canines finished erupting at about 34 to 41 months. Based on these developmental age calculations, S. fatalis individuals less than 4 to 7 months of age were not typically preserved at Rancho La Brea. On the whole, S. fatalis appears to have had delayed dental development compared to dental development in similar-sized extant felids. This technique for absolute ontogenetic age determination can be replicated in other ancient species, including non-saber-toothed taxa, as long as the timing of growth initiation and growth rate can be determined for a specific feature, such as a tooth, and that growth period overlaps with the development of the other features under investigation.

Severe tooth wear in Prader-Willi syndrome. A case–control study

Directory of Open Access Journals (Sweden)

Saeves Ronnaug

2012-05-01

Full Text Available Abstract Background Prader-Willi syndrome (PWS is a rare complex multsystemic genetic disorder characterized by severe neonatal hypotonia, endocrine disturbances, hyperphagia and obesity, mild mental retardation, learning disabilities, facial dysmorphology and oral abnormalities. The purpose of the present study was to explore the prevalence of tooth wear and possible risk factors in individuals with Prader-Willi syndrome. Methods Forty-nine individuals (6-40 years with PWS and an age- and sex-matched control group were included. Tooth wear was evaluated from dental casts and intraoral photographs and rated by four examiners using the Visual Erosion Dental Examination (VEDE scoring system and the individual tooth wear index IA. In accordance with the VEDE scoring system, tooth wear was also evaluated clinically. Whole saliva was collected. Results Mean VEDE score was 1.70 ± 1.44 in the PWS group and 0.46 ± 0.36 in the control group (p A was 7.50 (2.60-30.70 in the PWS group and 2.60 (0.90-4.70 among controls (p A; r = 0.82, p A; r = 0.43, p = 0.002. Tooth grinding was also associated with tooth wear in the PWS group, as indicated by the mean VEDE 2.67 ± 1.62 in grinders and 1.14 ± 0.97 in non-grinders (p = 0.001 and median IA values 25.70 (5.48-68.55 in grinders and 5.70 (1.60-9.10 in non-grinders (p = 0.003. Multivariate linear regression analysis was performed with tooth wear as the dependent variable and PWS (yes/no, age, tooth grinding and saliva secretion as independent variables. PWS (yes/no, age and tooth grinding retained a significant association with tooth wear, VEDE (p A (p  Conclusions Our study provides evidence that tooth wear, in terms of both erosion and attrition, is a severe problem in Prader-Willi syndrome. There is therefore considerable need for prosthodontic rehabilitation in young adults with PWS.

Tooth fragment reattachment techniques-A systematic review.

Science.gov (United States)

Garcia, Fernanda Cristina P; Poubel, Déborah L N; Almeida, Júlio César F; Toledo, Isabela P; Poi, Wilson R; Guerra, Eliete N S; Rezende, Liliana V M L

2018-03-07

Several strategies have been developed for tooth fragment reattachment following fracture. Although many techniques have been reported, there is no consensus on which one has the best results in terms of the bond strength between the fragment and the dentin over time. The aim of this study was to assess the currently reported tooth fragment reattachment techniques for fractured crowns of anterior teeth. The PubMed, LILACS, Web of Science, Cochrane, and Scopus databases were searched in October 2016, and the search was updated in February 2017. A search of the gray literature was performed in Google Scholar and OpenGrey. Reference lists of eligible studies were cross-checked to identify additional studies; gray literature and ongoing trials were investigated. Two authors assessed studies to determine inclusion and undertook data extraction. Case reports/series of three or more cases, cross-sectional studies, cohort studies, and in vivo clinical trials in all languages were included. Five articles remained after screening. These studies predominantly reported on fragment reattachment with composite resin and resin cement. There was little consistency among the studies in regard to the technique used for tooth fragment reattachment and length of the follow-up period. According to the evidence found in the studies included in this review, simple tooth fragment reattachment was the preferred reattachment technique. An increase in the bond strength between tooth fragment and dentin was observed when an intermediate material was used. Further investigation is needed, using standard follow-up periods and larger samples. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Electron paramagnetic resonance biophysical radiation dosimetry with tooth enamel

International Nuclear Information System (INIS)

Khan, Rao F.H.

2003-01-01

This thesis deals with the advancements made in the field of Electron Paramagnetic Resonance (EPR) for biophysical dosimetry with tooth enamel for accident, emergency, and retrospective radiation dose reconstruction. A methodology has been developed to measure retrospective radiation exposures in human tooth enamel. This entails novel sample preparation procedures with minimum mechanical treatment to reduce the preparation induced uncertainties, establish optimum measurement conditions inside the EPR cavity, post-process the measured spectrum with functional simulation of dosimetric and other interfering signals, and reconstruct dose. By using this technique, retrospective gamma exposures as low as 80±30 mGy have been successfully deciphered. The notion of dose modifier was introduced in EPR biodosimetry for low dose measurements. It has been demonstrated that by using the modified zero added dose (MZAD) technique for low radiation exposures, doses in 100 mGy ranges can be easily reconstructed in teeth that were previously thought useless for EPR dosimetry. Also, the use of a dose modifier makes robust dose reconstruction possible for higher radiation exposures. The EPR dosimetry technique was also developed for tooth samples extracted from rodents, which represent small tooth sizing. EPR doses in the molars, extracted from the mice irradiated with whole body exposures, were reassessed and shown to be correct within the experimental uncertainty. The sensitivity of human tooth enamel for neutron irradiation, obtained from the 3 MV McMaster K.N. Van de Graaff accelerator, was also studied. For the first time this work has shown that the neutron sensitivity of the tooth enamel is approximately 1/10th of the equivalent gamma sensitivity. Parametric studies for neutron dose rate and neutron energy within the available range of the accelerator, showed no impact on the sensitivity of the tooth enamel. Therefore, tooth enamel can be used as a dosimeter for both neutrons

Relationship between food habits and tooth erosion occurrence in Malaysian University students.

Science.gov (United States)

Manaf, Zahara Abdul; Lee, Mei Tee; Ali, Nor Hazirah Muhammad; Samynathan, Selvamary; Jie, Ying Phor; Ismail, Noor Hasnani; Bibiana Hui Ying, Yong; Wei Seng, Yeo; Yahya, Nurul Asyikin

2012-04-01

Tooth erosion is a growing dental problem; however, the role of diet in the aetiology of tooth erosion is unclear. A cross-sectional study was conducted to determine the association between tooth erosion occurrence and the consumption of acidic foods and drinks among undergraduate university students. A total of 150 undergraduate students (33 males and 117 females) aged 19 to 24 years at Universiti Kebangsaan Malaysia participated in this study. The Basic Erosive Wear Examination was used to assess the occurrence of tooth erosion. Information regarding dental hygiene practices, usual dietary habits, and consumption of acidic foods and drinks was obtained through a structured questionnaire. In all, 68% of subjects had tooth erosion. Subjects who reported having received information about healthy eating were less likely to have tooth erosion (χ(2) [1, N = 150] = 7.328, P = 0.007). The frequencies of milk (OR = 0.29, 95% CI = 0.13-0.67) and tea/coffee (adjusted OR = 0.42, 95% CI = 0.19-0.95) consumption were negatively associated with tooth erosion. Dental hygiene practice, the frequency and amount of acidic food and drink intake, and body mass index classification were not significantly associated with the risk of tooth erosion (P > 0.05). A high prevalence of tooth erosion was observed among this group of students. Preventive measures, such as dietary advice and increased consumption of milk at a younger age, may reduce the occurrence of tooth erosion among this age group.

Use of quantitative light-induced fluorescence to monitor tooth whitening

Science.gov (United States)

Amaechi, Bennett T.; Higham, Susan M.

2001-04-01

The changing of tooth shade by whitening agents occurs gradually. Apart from being subjective and affected by the conditions of the surroundings, visual observation cannot detect a very slight change in tooth color. An electronic method, which can communicate the color change quantitatively, would be more reliable. Quantitative Light- induced Fluorescence (QLF) was developed to detect and assess dental caries based on the phenomenon of change of autofluorescence of a tooth by demineralization. However, stains on the tooth surface exhibit the same phenomenon, and therefore QLF can be used to measure the percentage fluorescence change of stained enamel with respect to surrounding unstained enamel. The present study described a technique of assessing the effect of a tooth-whitening agent using QLF. This was demonstrated in two experiments in which either wholly or partially stained teeth were whitened by intermittent immersion in sodium hypochlorite. Following each immersion, the integrated fluorescence change due to the stain was quantified using QLF. In either situation, the value of (Delta) Q decreased linearly as the tooth regained its natural shade. It was concluded that gradual changing of the shade of discolored teeth by a whitening agent could be quantified using QLF.

To Tell the Tooth

Science.gov (United States)

... Activity Sheets 2018 Brushing Calendar Sports Safety National Nutrition Month Choose Water for a Sparkling Smile Holiday Workshop Thanksgiving Back to School Fourth of July Fun Tooth Fairy Sugar Wars Valentine's Day Halloween Defeat Monster Mouth! Color and ...

The development of complex tooth shape in reptiles

Science.gov (United States)

Zahradnicek, Oldrich; Buchtova, Marcela; Dosedelova, Hana; Tucker, Abigail S.

2014-01-01

Reptiles have a diverse array of tooth shapes, from simple unicuspid to complex multicuspid teeth, reflecting functional adaptation to a variety of diets and eating styles. In addition to cusps, often complex longitudinal labial and lingual enamel crests are widespread and contribute to the final shape of reptile teeth. The simplest shaped unicuspid teeth have been found in piscivorous or carnivorous ancestors of recent diapsid reptiles and they are also present in some extant carnivores such as crocodiles and snakes. However, the ancestral tooth shape for squamate reptiles is thought to be bicuspid, indicating an insectivorous diet. The development of bicuspid teeth in lizards has recently been published, indicating that the mechanisms used to create cusps and crests are very distinct from those that shape cusps in mammals. Here, we introduce the large variety of tooth shapes found in lizards and compare the morphology and development of bicuspid, tricuspid, and pentacuspid teeth, with the aim of understanding how such tooth shapes are generated. Next, we discuss whether the processes used to form such morphologies are conserved between divergent lizards and whether the underlying mechanisms share similarities with those of mammals. In particular, we will focus on the complex teeth of the chameleon, gecko, varanus, and anole lizards using SEM and histology to compare the tooth crown morphology and embryonic development. PMID:24611053

The development of complex tooth shape in reptiles

Directory of Open Access Journals (Sweden)

Oldrich eZahradnicek

2014-02-01

Full Text Available Reptiles have a diverse array of tooth shapes, from simple unicuspid to complex multicuspid teeth, reflecting functional adaptation to a variety of diets and eating styles. In addition to cusps, often complex longitudinal labial and lingual enamel crests are widespread and contribute to the final shape of reptile teeth. The simplest shaped unicuspid teeth have been found in piscivorous or carnivorous ancestors of recent diapsid reptiles and they are also present in some extant carnivores such as crocodiles and snakes. However, the ancestral tooth shape for squamate reptiles is thought to be bicuspid, indicating an insectivorous diet. The development of bicuspid teeth in lizards has recently been published, indicating that the mechanisms used to create cusps and crests are very distinct from those that shape cusps in mammals. Here, we introduce the large variety of tooth shapes found in lizards and compare the morphology and development of bicuspid, tricuspid and pentacuspid teeth, with the aim of understanding how such tooth shapes are generated. Next, we discuss whether the processes used to form such morphologies are conserved between divergent lizards and whether the underlying mechanisms share similarities with those of mammals. In particular, we will focus on the complex teeth of the chameleon, gecko, varanus and anole lizards using SEM and histology to compare the tooth crown morphology and embryonic development.

Mechanisms underlying ectopic persistent tooth-pulp pain following pulpal inflammation.

Directory of Open Access Journals (Sweden)

Shingo Matsuura

Full Text Available In order to clarify the peripheral mechanisms of ectopic persistent pain in a tooth pulp following pulpal inflammation of an adjacent tooth, masseter muscle activity, phosphorylated extracellular signal-regulated protein kinase (pERK and TRPV1 immunohistochemistries and satellite cell activation using glial fibrillary acidic protein (GFAP immunohistochemistry in the trigeminal ganglion (TG were studied in the rats with molar tooth-pulp inflammation. And, Fluorogold (FG and DiI were also used in a neuronal tracing study to analyze if some TG neurons innervate more than one tooth pulp. Complete Freund's adjuvant (CFA or saline was applied into the upper first molar tooth pulp (M1 in pentobarbital-anesthetized rats, and capsaicin was applied into the upper second molar tooth pulp (M2 on day 3 after the CFA or saline application. Mean EMG activity elicited in the masseter muscle by capsaicin application to M2 was significantly larger in M1 CFA-applied rats compared with M1 vehicle-applied rats. The mean number of pERK-immunoreactive (IR TG cells was significantly larger in M1 CFA-applied rats compared with M1 vehicle-applied rats. Application of the satellite cell inhibitor fluorocitrate (FC into TG caused a significant depression of capsaicin-induced masseter muscle activity and a significant reduction of satellite cell activation. The number of TRPV1-IR TG cells innervating M2 was significantly larger in M1 CFA-applied rats compared with M1 vehicle-applied rats, and that was decreased following FC injection into TG. Furthermore, 6% of TG neurons innervating M1 and/or M2 innervated both M1 and M2. These findings suggest that satellite cell activation following tooth pulp inflammation and innervation of multiple tooth pulps by single TG neurons may be involved in the enhancement of the activity of TG neurons innervating adjacent non-inflamed teeth that also show enhancement of TRPV1 expression in TG neurons, resulting in the ectopic persistent tooth

Computer simulation of gear tooth manufacturing processes

Science.gov (United States)

Mavriplis, Dimitri; Huston, Ronald L.

1990-01-01

The use of computer graphics to simulate gear tooth manufacturing procedures is discussed. An analytical basis for the simulation is established for spur gears. The simulation itself, however, is developed not only for spur gears, but for straight bevel gears as well. The applications of the developed procedure extend from the development of finite element models of heretofore intractable geometrical forms, to exploring the fabrication of nonstandard tooth forms.

Tooth-germ damage by ionizing radiation

International Nuclear Information System (INIS)

Sobkowiak, E.M.; Beetke, E.; Bienengraeber, V.; Held, M.; Kittner, K.H.

1977-01-01

Experiments on animals (four-week-old dogs) were conducted in an investigation made to study the possibility of dose-dependent tooth-germ damage produced by ionizing radiation. The individual doses were 50 R and 200 R, respectively, and they were administered once to three times at weekly intervals. Hyperemia and edemata could be observed on tooth-germ pulps from 150 R onward. Both of these conditions became more acute as the radiation dose increased (from 150 R to 600 R). Possible damage to both the dentin and enamel is pointed out. (author)

Effect of the vitality of the overdenture abutment tooth on stability of the tooth

Directory of Open Access Journals (Sweden)

Khalid Ahmad Omar Arafa

2016-01-01

Conclusion: It was concluded that the overdenture over vital abutment teeth was more stable, with a lower incidence of tooth mobility and less attachment loss than overdentures placed on nonvital teeth.

Daylong Effect of Tooth Brushing or Combination Tooth Brushing and Tongue Cleaning Using Antiplaque®Toothpaste on Volatile Sulphur Compound Levels

Directory of Open Access Journals (Sweden)

Indriasti Indah Wardhany

2013-07-01

Full Text Available Objective: to determine the daylong effect of Antiplaque® toothpaste active copound and the effect of tooth brushing or combination of tooth brushing and tongue cleaning on Volatile Sulphur Compounds (VSC levels. Methods: Clinical experimental double blinded microbiological and clinical examination. Subjects mainly from dental faculty student with or without a chief complain of halitosis. One hundred and twenty subjects were divided into four groups that consist of thirty samples each group. Two group are treatment subjects were divided into four groups that consist thirty samples each group. Two groups are treatment groups using Antiplaque® toothpaste and two groups are control groups using placebo toothpaste. The daylong effects of VSC levels are measured by Halimeter and organoleptic. The intraoral status were measured including periodontal status and tongue index. Result: There are a reduction of VSC levels in both treatment and control group, but the reduction only significant in group using Antiplaque® toothpaste (Wilcoxon signed rank test, p<0.05. There are a reduction of VSC levels in both treatment using Antiplaque® toothpaste, but the combination of tooth brushing and tongue cleaning reduced VSC levels significantly lower than tooth brushing treatment (Mann Whitney U test, P,0.05. Conclusion: Tooth brushing and tongue cleaning using Antiplaque® toothpaste significantly reduced VSC levels.DOI: 10.14693/jdi.v16i2.95

The effect of light-activation sources on tooth bleaching

Science.gov (United States)

Baroudi, Kusai; Hassan, Nadia Aly

2014-01-01

Vital bleaching is one of the most requested cosmetic dental procedures asked by patients who seek a more pleasing smile. This procedure consists of carbamide or hydrogen peroxide gel applications that can be applied in-office or by the patient (at-home/overnight bleaching system). Some in-office treatments utilise whitening light with the objective of speeding up the whitening process. The objective of this article is to review and summarise the current literature with regard to the effect of light-activation sources on in-office tooth bleaching. A literature search was conducted using Medline, accessed via the National Library of Medicine Pub Med from 2003 to 2013 searching for articles relating to effectiveness of light activation sources on in-office tooth bleaching. This study found conflicting evidence on whether light truly improve tooth whitening. Other factors such as, type of stain, initial tooth colour and subject age which can influence tooth bleaching outcome were discussed. Conclusions: The use of light activator sources with in-office bleaching treatment of vital teeth did not increase the efficacy of bleaching or accelerate the bleaching. PMID:25298598

Tooth wear

OpenAIRE

Tušek Ivan; Tušek Jasmina

2014-01-01

Tooth wear is the loss of dental hard tissue that was not caused by decay and represents a common clinical problem of modern man. In the etiology of dental hard tissue lesions there are three dominant mechanisms that may act synergistically or separately:friction (friction), which is caused by abrasion of exogenous, or attrition of endogenous origin, chemical dissolution of dental hard tissues caused by erosion, occlusal stress created by compression and flexion and tension that leads to toot...

Effect of Cervical Lessions on the Tooth FEM Study

Directory of Open Access Journals (Sweden)

Gabriela Bereşescu

2010-12-01

Full Text Available The approach used until recently concerning the phenomena of dental abfraction points to the conclusion that the cervical area of the tooth, were this type of lesion usually occur, concentrates the stress resulted from the action of the forces applied on various areas on the crown. Moreover, any lesion in the cervical area facilitates the possibility of its advance into the tooth, ultimately fracturing it. Our paper presents a FEM (finite element method study on the results of a mechanical analysis of the phenomena involving the tooth damaged by cervical lesions.

Reliability of the CMT neuropathy score (second version) in Charcot-Marie-Tooth disease.

LENUS (Irish Health Repository)

Murphy, Sinéad M

2011-09-01

The Charcot-Marie-Tooth neuropathy score (CMTNS) is a reliable and valid composite score comprising symptoms, signs, and neurophysiological tests, which has been used in natural history studies of CMT1A and CMT1X and as an outcome measure in treatment trials of CMT1A. Following an international workshop on outcome measures in Charcot-Marie-Tooth disease (CMT), the CMTNS was modified to attempt to reduce floor and ceiling effects and to standardize patient assessment, aiming to improve its sensitivity for detecting change over time and the effect of an intervention. After agreeing on the modifications made to the CMTNS (CMTNS2), three examiners evaluated 16 patients to determine inter-rater reliability; one examiner evaluated 18 patients twice within 8 weeks to determine intra-rater reliability. Three examiners evaluated 63 patients using the CMTNS and the CMTNS2 to determine how the modifications altered scoring. For inter- and intra-rater reliability, intra-class correlation coefficients (ICCs) were ≥0.96 for the CMT symptom score and the CMT examination score. There were small but significant differences in some of the individual components of the CMTNS compared with the CMTNS2, mainly in the components that had been modified the most. A longitudinal study is in progress to determine whether the CMTNS2 is more sensitive than the CMTNS for detecting change over time.

Proteomic Analysis of Human Tooth Pulp: Proteomics of Human Tooth

Czech Academy of Sciences Publication Activity Database

Eckhardt, Adam; Jágr, Michal; Pataridis, Statis; Mikšík, Ivan

2014-01-01

Roč. 40, č. 12 (2014), s. 1961-1966 ISSN 0099-2399 R&D Projects: GA ČR(CZ) GA13-17224S; GA ČR(CZ) GAP206/12/0453; GA MZd(CZ) NT14324 Institutional support: RVO:67985823 Keywords : dentin * human pulp * tandem mass spectrometry * tooth proteome * 2-dimensional gel electrophoresis Subject RIV: FF - HEENT, Dentistry Impact factor: 3.375, year: 2014

Tooth-coil permanent magnet synchronous machine design for special applications

Energy Technology Data Exchange (ETDEWEB)

Ponomarev, P.

2013-11-01

This doctoral thesis presents a study on the design of tooth-coil permanent magnet synchronous machines. The electromagnetic properties of concentrated non-overlapping winding permanent magnet synchronous machines, or simply tooth-coil permanent magnet synchronous machines (TC-PMSMs), are studied in details. It is shown that current linkage harmonics play the deterministic role in the behavior of this type of machines. Important contributions are presented as regards of calculation of parameters of TC-PMSMs,particularly the estimation of inductances. The current linkage harmonics essentially define the air-gap harmonic leakage inductance, rotor losses and localized temporal inductance variation. It is proven by FEM analysis that inductance variation caused by the local temporal harmonic saturation results in considerable torque ripple, and can influence on sensorless control capabilities. Example case studies an integrated application of TC-IPMSMs in hybrid off-highway working vehicles. A methodology for increasing the efficiency of working vehicles is introduced. It comprises several approaches - hybridization, working operations optimization, component optimization and integration. As a result of component optimization and integration, a novel integrated electro-hydraulic energy converter (IEHEC) for off-highway working vehicles is designed. The IEHEC can considerably increase the operational efficiency of a hybrid working vehicle. The energy converter consists of an axial-piston hydraulic machine and an integrated TCIPMSM being built on the same shaft. The compact assembly of the electrical and hydraulic machines enhances the ability to find applications for such a device in the mobile environment of working vehicles.Usage of hydraulic fluid, typically used in working actuators, enables direct-immersion oil cooling of designed electrical machine, and further increases the torque- and power- densities of the whole device. (orig.)

Claustral single cell reactions to tooth pulp stimulation in cats.

Science.gov (United States)

Jastreboff, P; Sikora, M; Frydrychowski, A; Słoniewski, P

1983-01-01

Single unit activity in the central region of the claustrum, evoked by electrical stimulation of tooth pulp or paws was studied on cats under chloralose anesthesia. The majority of cells responded in similar manner to stimulation of tooth pulp or paws, but there were cells with clear preference to a given type of stimulation. Latencies of reactions evoked by tooth pulp stimulation were significantly shorter than those for limb stimulation. In the former case latencies as short as 8 rns were observed. It is postulated that the central region of the claustrum receives a projection from the tooth pulp, and that in those cases with very short latency the projection is direct and does not involve the cerebral cortex.

Tooth erosion and eating disorders: a systematic review and meta-analysis.

Directory of Open Access Journals (Sweden)

Ana Paula Hermont

Full Text Available BACKGROUND: Eating disorders are associated with the highest rates of morbidity and mortality of any mental disorders among adolescents. The failure to recognize their early signs can compromise a patient's recovery and long-term prognosis. Tooth erosion has been reported as an oral manifestation that might help in the early detection of eating disorders. OBJECTIVES: The aim of this systematic review and meta-analysis was to search for scientific evidence regarding the following clinical question: Do eating disorders increase the risk of tooth erosion? METHODS: An electronic search addressing eating disorders and tooth erosion was conducted in eight databases. Two independent reviewers selected studies, abstracted information and assessed its quality. Data were abstracted for meta-analysis comparing tooth erosion in control patients (without eating disorders vs. patients with eating disorders; and patients with eating disorder risk behavior vs. patients without such risk behavior. Combined odds ratios (ORs and a 95% confidence interval (CI were obtained. RESULTS: Twenty-three papers were included in the qualitative synthesis and assessed by a modified version of the Newcastle-Ottawa Scale. Fourteen papers were included in the meta-analysis. Patients with eating disorders had more risk of tooth erosion (OR = 12.4, 95%CI = 4.1-37.5. Patients with eating disorders who self-induced vomiting had more risk of tooth erosion than those patients who did not self-induce vomiting (OR = 19.6, 95%CI = 5.6-68.8. Patients with risk behavior of eating disorder had more risk of tooth erosion than patients without such risk behavior (Summary OR = 11.6, 95%CI = 3.2-41.7. CONCLUSION: The scientific evidence suggests a causal relationship between tooth erosion and eating disorders and purging practices. Nevertheless, there is a lack of scientific evidence to fulfill the basic criteria of causation between the risk behavior for eating disorders and tooth erosion.

A Dental Hygienist's and Therapist's Guide to the Management of Tooth Erosion.

Science.gov (United States)

Ariyanayagam, Yana

2016-08-01

Dental care professionals can support patients to prevent and manage tooth erosion. The role of the dentist is to restore the structure and function of teeth damaged by acid erosion, while the role of the dental hygienist therapist is to work alongside the dentist to help manage and reduce the risk of tooth erosion. This article will highlight how the dental hygienist or therapist can identify tooth erosion. It will describe the features of tooth erosion and outline the causes. This article will discuss preventative care options for patients who are at risk of tooth erosion, including specific oral hygiene instructions, fluoride advice and use of other dental products.

A design of speed reducer with trapezoidal tooth profile for robot manipulator

Energy Technology Data Exchange (ETDEWEB)

Nam, Won Ki; Oh, Se Hoon [Chung-Ang University, Seoul (Korea, Republic of)

2011-01-15

Robots are increasingly performing human work as manufacturing is automated. Accordingly, the use of precision speed reducers has become essential for achieving precise control of the robot arm position. Curved tooth profiles, such as cycloid or involute tooth profiles, are generally used in precision speed reducers. Speed reducers with cycloid tooth profiles, which enable high precision control, are widely used to manipulate robot systems. This study proposes a speed reducer that has a trapezoidal tooth profile with straight lines. In this work, we mechanically analyzed trapezoidal tooth profiles, and then measured performance was by various tests using a prototype manufactured specifically for this study.

A design of speed reducer with trapezoidal tooth profile for robot manipulator

International Nuclear Information System (INIS)

Nam, Won Ki; Oh, Se Hoon

2011-01-01

Robots are increasingly performing human work as manufacturing is automated. Accordingly, the use of precision speed reducers has become essential for achieving precise control of the robot arm position. Curved tooth profiles, such as cycloid or involute tooth profiles, are generally used in precision speed reducers. Speed reducers with cycloid tooth profiles, which enable high precision control, are widely used to manipulate robot systems. This study proposes a speed reducer that has a trapezoidal tooth profile with straight lines. In this work, we mechanically analyzed trapezoidal tooth profiles, and then measured performance was by various tests using a prototype manufactured specifically for this study

Mesiodistal tooth angulation to segmental occlusal plane in panoramic radiography

International Nuclear Information System (INIS)

Kim, Jae Duk; Kim, Jin Soo; You, Choong Hyun

2005-01-01

To evaluate the stability of the segmental occlusal plane and anatomical line as the reference line for measuring the mesiodistal tooth angulation in panoramic radiography and to determine the mean angle and the range of the mesiodistal tooth angulation in Korean population with normal occlusions. Twenty nine subjects (15 men, 14 women) with normal occlusion were selected. A total of 29 panoramic radiograms were taken at normal head position and then 10 images of 5 subjects selected were repeatedly taken with repositioning 2 times at each of the head down (V-shaped occlusion) and up (horizontal occulsion) for evaluation of stability of adopted reference lines by using PM2002CC (Planmeca, Finland). The images were traced with adoption of two test reference lines and the long axes of the teeth. The mesial angles formed by each reference line and the long axes of the teeth were measured and analyzed. With anatomical reference line, the mesiodistal tooth angulations of the molars showed the significant difference by over 5 degree between the normal and each changed head position. With segmented occlusal reference line, deviations of mesiodistal tooth angulations by the two changed head positions were less than 1 degree. The means, standard deviations, and maximum and minimum values of mesiodistal tooth angulations to segmental occlusal reference line on panoramic radiography were determined. It would appear that mesiodistal tooth angulations to segmental occlusal plane as reference line in panograms are predictable as standards of normal occlusion and useful for evaluation of tooth arrangement between adjacent teeth.

Mesiodistal tooth angulation to segmental occlusal plane in panoramic radiography

Energy Technology Data Exchange (ETDEWEB)

Kim, Jae Duk; Kim, Jin Soo; You, Choong Hyun [Chosun University College of Medicine, Kwangju (Korea, Republic of)

2005-03-15

To evaluate the stability of the segmental occlusal plane and anatomical line as the reference line for measuring the mesiodistal tooth angulation in panoramic radiography and to determine the mean angle and the range of the mesiodistal tooth angulation in Korean population with normal occlusions. Twenty nine subjects (15 men, 14 women) with normal occlusion were selected. A total of 29 panoramic radiograms were taken at normal head position and then 10 images of 5 subjects selected were repeatedly taken with repositioning 2 times at each of the head down (V-shaped occlusion) and up (horizontal occulsion) for evaluation of stability of adopted reference lines by using PM2002CC (Planmeca, Finland). The images were traced with adoption of two test reference lines and the long axes of the teeth. The mesial angles formed by each reference line and the long axes of the teeth were measured and analyzed. With anatomical reference line, the mesiodistal tooth angulations of the molars showed the significant difference by over 5 degree between the normal and each changed head position. With segmented occlusal reference line, deviations of mesiodistal tooth angulations by the two changed head positions were less than 1 degree. The means, standard deviations, and maximum and minimum values of mesiodistal tooth angulations to segmental occlusal reference line on panoramic radiography were determined. It would appear that mesiodistal tooth angulations to segmental occlusal plane as reference line in panograms are predictable as standards of normal occlusion and useful for evaluation of tooth arrangement between adjacent teeth.

UV EFFECTS IN TOOTH ENAMEL AND THEIR POSSIBLE APPLICATION IN EPR DOSIMETRY WITH FRONT TEETH

Science.gov (United States)

Sholom, S.; Desrosiers, M.; Chumak, V.; Luckyanov, N.; Simon, S.L.; Bouville, A.

2009-01-01

The effects of ultraviolet (UV) radiation on ionizing radiation biodosimetry were studied in human tooth enamel samples using the technique of electron paramagnetic resonance (EPR) in X-band. For samples in the form of grains, UV-specific EPR spectra were spectrally distinct from that produced by exposure to gamma radiation. From larger enamel samples, the UV penetration depth was determined to be in the 60–120 μm range. The difference in EPR spectra from UV exposure and from exposure to gamma radiation samples was found to be a useful marker of UV equivalent dose (defined as the apparent contribution to the gamma dose in mGy that results from UV radiation absorption) in tooth enamel. This concept was preliminarily tested on front teeth from inhabitants of the region of the Semipalatinsk Nuclear Test Site (Kazakhstan) who might have received some exposure to gamma radiation from the nuclear tests conducted there as well as from normal UV radiation in sunlight. The technique developed here to quantify and subtract the UV contribution to the measured tooth is currently limited to cumulative dose measurements with a component of UV equivalent dose equal to or greater than 300 mGy. PMID:20065706

Stem cells applications in bone and tooth repair and regeneration: New insights, tools, and hopes.

Science.gov (United States)

Abdel Meguid, Eiman; Ke, Yuehai; Ji, Junfeng; El-Hashash, Ahmed H K

2018-03-01

The exploration of stem and progenitor cells holds promise for advancing our understanding of the biology of tissue repair and regeneration mechanisms after injury. This will also help in the future use of stem cell therapy for the development of regenerative medicine approaches for the treatment of different tissue-species defects or disorders such as bone, cartilages, and tooth defects or disorders. Bone is a specialized connective tissue, with mineralized extracellular components that provide bones with both strength and rigidity, and thus enable bones to function in body mechanical supports and necessary locomotion process. New insights have been added to the use of different types of stem cells in bone and tooth defects over the last few years. In this concise review, we briefly describe bone structure as well as summarize recent research progress and accumulated information regarding the osteogenic differentiation of stem cells, as well as stem cell contributions to bone repair/regeneration, bone defects or disorders, and both restoration and regeneration of bones and cartilages. We also discuss advances in the osteogenic differentiation and bone regeneration of dental and periodontal stem cells as well as in stem cell contributions to dentine regeneration and tooth engineering. © 2017 Wiley Periodicals, Inc.

Roentgenologic investigations for the anterior tooth length

Energy Technology Data Exchange (ETDEWEB)

Cho, Won Pyo; Ahn, Hyung Kyu [College of Dentistry, Seoul National University , Seoul (Korea, Republic of)

1972-11-15

The author measured the length of crown, root and tooth on the films which was taken by intraoral bisecting technic with mesh plate on the films. The films were taken from the dry skulls, dentiform, same patients who had to be removed their upper incisors, and the other patients who admitted for dental care. From this serial experiment the results were made as follows: 1. By using the film and mesh plate in the oral cavity, the real tooth length can be measured easily on the film surfaces. 2. The film distortion in the oral cavity can be avoided when taking the film using the mesh plate and film together. 3. When measuring the film, length of crown was elongated and length of root was shortened. 4. When using the well-trained bisecting technic, the real tooth length can be measured directly on the intraoral film.

Relationship between human tooth enamel free radical concentration and radiation dose

International Nuclear Information System (INIS)

Zhou Yongzeng; Wang Jiadong; Jia Xiaomei; Wu Ke; Cong Jianbo; Sun Cunpu

1999-01-01

Free radical concentrations of 25 adult tooth enamel samples were measured by electron spin resonance (ESR) technique in this paper, and the relationship between free radical concentration of tooth enamel and radiation dose was also investigated. In the 25 adult enamel samples they are 16 male samples and 9 female samples, Ages of tooth donors range from 18-41 years. Difference in background ESR signal intensity between male and female samples was no observed; free radical concentration (or increment of radiation-induced free radical concentration) in tooth enamel increases linearly with increasing of radiation dose. In the case of radiation accident, the study results of this paper could be applied to dose estimation when conditions of ESR measurement of exposed individual tooth enamel are similar to measurement conditions of dose-effect calibration curve in this paper

Australian aboriginal tooth succession, interproximal attrition, and Begg's theory.

Science.gov (United States)

Corruccini, R S

1990-04-01

In 1954, P.R. Begg analyzed interproximal attrition as a prehistorically universal mechanism to reduce tooth size. With modern processed diets and the virtual disappearance of constant interproximal attrition, Begg asserted, teeth remain too large for the arches and become crowded. Later investigators have questioned Begg's estimate of attritional tooth-size reduction, as well as aspects of his theory relating the succession sequence of permanent teeth to different malocclusions. The present paper examines the theory using longitudinal casts and records of modern Australian aborigines who are among the first generation lacking notable interproximal attrition thanks to a "modernized" diet. Deciduous and permanent tooth size, arch size, and occlusal relational variables were analyzed with respect to the expected occlusal outcomes in the absence of attritional tooth reduction. Permanent incisor overjet correlated with crowding status, as predicted by Begg. On the other hand, longer teeth did not relate to crowding in general nor to crowding in relevant local areas or during developmental stages. Unfavorable leeway space did not relate clearly to crowding or other malocclusions. Lowered correlations among structures and narrowness of the maxilla related more significantly to malocclusion. These results are in keeping with recent thinking that small jaws rather than large teeth underlie tooth/arch discrepancy.

Nutritional status, tooth wear and quality of life in Brazilian schoolchildren.

Science.gov (United States)

Andrade, Francisco Juliherme Pires de; Sales-Peres, André de Carvalho; Moura-Grec, Patricia Garcia de; Mapengo, Marta Artemisa Abel; Sales-Peres, Arsenio; Sales-Peres, Sílvia Helena de Carvalho

2016-06-01

To evaluate the correlation among nutritional status, tooth wear and quality of life in Brazilian schoolchildren. The study followed a cross-sectional design. Nutritional status was measured via anthropometry using BMI and tooth wear was measured using the Dental Wear Index; both these assessments were carried out by a trained recorder according to standard criteria. A modified version of the Child Oral Impacts on Daily Performances was used to assess quality of life. City of Bauru, in Brazil. A cluster sample of 396 schoolchildren (194 boys and 202 girls) aged 7-10 years. The anthropometric assessment showed similar situations for both sexes regarding underweight (31·40 % in boys and 30·20 % in girls) and overweight/obesity (33·96 % in boys and 33·17 % in girls). The underweight children showed a greater severity of tooth wear in the primary teeth (OR=0·72; CI 0·36, 1·42), although in the permanent dentition the obese children had a greater severity of tooth wear (OR=1·42; 95 % CI 0·31, 6·55). The tooth wear was correlated with age for both dentitions. Tooth wear in the primary and permanent dentition may be related to nutritional status. Tooth wear and obesity did not have a significant impact on the schoolchildren's perception of quality of life.

Anomalies of tooth formation in hypohidrotic ectodermal dysplasia

DEFF Research Database (Denmark)

Lexner, Michala O; Bardow, Allan; Hertz, Jens Michael

2007-01-01

OBJECTIVE: The X-linked hypohidrotic ectodermal dysplasia (HED) is the most common type of ectodermal dysplasia. The clinical identification of possible heterozygous females can be difficult because of the varying degrees of clinical signs caused by X-chromosome inactivation. This study is the fi......OBJECTIVE: The X-linked hypohidrotic ectodermal dysplasia (HED) is the most common type of ectodermal dysplasia. The clinical identification of possible heterozygous females can be difficult because of the varying degrees of clinical signs caused by X-chromosome inactivation. This study...... affected males had multiple missing permanent teeth and tooth malformations. The heterozygous females had a significantly higher frequency of agenesis of permanent teeth compared to normative data. The heterozygous females had an increased prevalence of tooth malformations and reduced tooth size...

Jaw lesions associated with impacted tooth: A radiographic diagnostic guide

Energy Technology Data Exchange (ETDEWEB)

Motazavi, Hamed; Bharvand, Maryam [Dept. of Oral Medicine, School of Dentistry, Shahid Beheshti University of Medical Sciences, Tehran (Iran, Islamic Republic of)

2016-09-15

This review article aimed to introduce a category of jaw lesions associated with impacted tooth. General search engines and specialized databases such as Google Scholar, PubMed, PubMed Central, MedLine Plus, Science Direct, Scopus, and well-recognized textbooks were used to find relevant studies using keywords such as 'jaw lesion', 'jaw disease', 'impacted tooth', and 'unerupted tooth'. More than 250 articles were found, of which approximately 80 were broadly relevant to the topic. We ultimately included 47 articles that were closely related to the topic of interest. When the relevant data were compiled, the following 10 lesions were identified as having a relationship with impacted tooth: dentigerous cysts, calcifying odontogenic cysts, unicystic (mural) ameloblastomas, ameloblastomas, ameloblastic fibromas, adenomatoid odontogenic tumors, keratocystic odontogenic tumors, calcifying epithelial odontogenic tumors, ameloblastic fibro-odontomas, and odontomas. When clinicians encounter a lesion associated with an impacted tooth, they should first consider these entities in the differential diagnosis. This will help dental practitioners make more accurate diagnoses and develop better treatment plans based on patients' radiographs.

Efficacy of tooth whitening with different calcium phosphate-based formulations.

Science.gov (United States)

Jin, Jian; Xu, Xiaohui; Lai, Guangyun; Kunzelmann, Karl-Heinz

2013-08-01

The aim of this in-vitro study was to evaluate the efficacy of tooth whitening using different calcium phosphate-based formulations. Teeth were treated with three different hydroxyapatite preparations at different concentrations and with two control preparations; each tooth was treated a total of three times. After application of the last material, hydrodynamic shear force was applied to mimic mechanical loading. After each treatment, tooth color was measured using a dental spectrophotometer, and the mean changes in L*a*b* values between different measurements were expressed as ∆E. The results indicated significant differences between the materials, but neither dose- nor time-dependent associations were found. The suspension containing tricalcium phosphate (10 wt%) showed the most obvious color change (∆E = 2.20 ± 0.90), while the suspension containing zinc-carbonate-apatite (20 wt%) showed the least obvious color change (∆E = 0.91 ± 0.50). Calcium phosphate-based formulations that can adhere to the enamel surface and contribute to tooth whitening have promising tooth-whitening potential. © 2013 Eur J Oral Sci.

Jaw lesions associated with impacted tooth: A radiographic diagnostic guide

International Nuclear Information System (INIS)

Motazavi, Hamed; Bharvand, Maryam

2016-01-01

This review article aimed to introduce a category of jaw lesions associated with impacted tooth. General search engines and specialized databases such as Google Scholar, PubMed, PubMed Central, MedLine Plus, Science Direct, Scopus, and well-recognized textbooks were used to find relevant studies using keywords such as 'jaw lesion', 'jaw disease', 'impacted tooth', and 'unerupted tooth'. More than 250 articles were found, of which approximately 80 were broadly relevant to the topic. We ultimately included 47 articles that were closely related to the topic of interest. When the relevant data were compiled, the following 10 lesions were identified as having a relationship with impacted tooth: dentigerous cysts, calcifying odontogenic cysts, unicystic (mural) ameloblastomas, ameloblastomas, ameloblastic fibromas, adenomatoid odontogenic tumors, keratocystic odontogenic tumors, calcifying epithelial odontogenic tumors, ameloblastic fibro-odontomas, and odontomas. When clinicians encounter a lesion associated with an impacted tooth, they should first consider these entities in the differential diagnosis. This will help dental practitioners make more accurate diagnoses and develop better treatment plans based on patients' radiographs

Development of Plastic Gear for Power Transmission : Abnormal Wear on the Tooth Root and Tooth Fracture near Pitch Point

OpenAIRE

Terashima, Kenichi; Tsukamoto, Naohisa; Nishida, Noriteru; Shi, Jiasun

1986-01-01

Plastic gears have many excellent characteristics which are locking in metallic gears, such as corrosion resistance, self-lubrication, quiet running, and so forth. The meshing behavior of plastic gears is very different from that of metallic gears. Therefore, the life estimation is very difficult for plastic gears. In this paper, generating and growing mechanisms of abnormal wear which appears fatally near the root of plastic tooth are analyzed, and then it is clarified that tooth fractures w...

A comparison of new and conventional methods for quantification of tooth color

NARCIS (Netherlands)

Burgt, van der T.P.; Bosch, ten J.J.; Borsboom, P.C.F.; Kortsmit, W.J.P.M.

1990-01-01

Tooth color is caused by volume reflection, that is, passage of incident light through the tooth followed by backward emergence. This passage is concurrent with sideward displacement of photons that, in effect, influences the result of usual instrumental methods of determining tooth color. This

SIGNS Molar tooth sign − looking beyond the obvious

African Journals Online (AJOL)

tooth are represented by thick, perpendicular, non-decussated superior cerebellar peduncles, while the 'body' of the molar tooth is formed by the cerebral peduncles of the brainstem with a deep interpeduncular fossa (Fig. 1a).[3]. Diffusion tensor tractography confirms the failure of superior cerebellar peduncle decussation.

Treatment of Necrotic Calcified Tooth Using Intentional Replantation Procedure

Directory of Open Access Journals (Sweden)

Nima Moradi Majd

2014-01-01

Full Text Available Introduction. If the teeth are impacted by a chronic irritant, the pulp space possibly will undergo calcific changes that may impede access opening during root canal treatment. In such cases that conventional endodontic treatment is impossible or impractical, intentional replantation may be considered as a last solution to preserve the tooth. Methods. After failing to perform conventional root canal therapy for a necrotic calcified right mandibular second premolar, the tooth was gently extracted. The root apex was resected and the root end cavity was prepared and filled with calcium enriched mixture (CEM cement. Then, the extracted tooth was replanted in its original position. Results. After a year the tooth was asymptomatic, and the size of periapical radiolucency was remarkably reduced and no clinical sign of ankylosis was observed. Conclusion. Intentional replantation of the necrotic calcified teeth could be considered as an alternative to teeth extraction, especially for the single-rooted teeth and when nonsurgical and surgical endodontic procedures seem impossible.

Tooth wear risk assessment and care-planning in general dental practice.

Science.gov (United States)

O'Toole, S; Khan, M; Patel, A; Patel, N J; Shah, N; Bartlett, D; Movahedi, S

2018-03-09

Objective To assess charting, risk assessment and treatment-planning of tooth wear between recently qualified and experienced dentists in general dental practice.Design Service evaluation.Setting Multi-setting evaluation of three mixed NHS/Private general dental practices in North-East London.Methods The clinical notes of new patient examinations on dentate adults presenting from the 1 October 2016 to 31 December 2016 were audited collecting data on tooth wear charting, risk assessment and treatment planning. Data were analysed using descriptives, chi square and logistic regressions in SPSS. Significance was inferred at p charted for 48% of those attending foundation dentists and 5% of those attending experienced dentists. Diet was assessed in 50.6% of patients examined by foundation dentists and 1.0% of patients examined by experienced dentists. Foundation dentists were more likely to chart tooth wear, risk assess and preventively manage tooth wear compared to experienced dentists (p <0.001).Conclusion This service evaluation highlights that improvements are required in recording, risk assessing and preventive treatment planning of erosive tooth wear. Experienced dentists were less likely to risk assess tooth wear and less likely to provide preventive treatment. Experienced GDPs may benefit from re-training in this area.

Camel molar tooth enamel response to gamma rays using EPR spectroscopy.

Science.gov (United States)

El-Faramawy, N A; El-Somany, I; Mansour, A; Maghraby, A M; Eissa, H; Wieser, A

2018-03-01

Tooth enamel samples from molar teeth of camel were prepared using a combined procedure of mechanical and chemical tooth treatment. Based on electron paramagnetic resonance (EPR) spectroscopy, the dose response of tooth enamel samples was examined and compared to that of human enamel. The EPR dose response of the tooth enamel samples was obtained through irradiation to gamma doses from 1 Gy up to 100 kGy. It was found that the radiation-induced EPR signal increased linearly with gamma dose for all studied tooth enamel samples, up to about 15 kGy. At higher doses, the dose response curve leveled off. The results revealed that the location of the native signal of camel tooth enamel was similar to that of enamel from human molars at 2.00644, but different from that of enamel from cows and goats. In addition, the peak-to-peak width (ΔH pp ) for human and camel molar teeth was similar. It was also found that the response of camel enamel to gamma radiation was 36% lower than that of human enamel. In conclusion, the results indicate the suitability of camel teeth for retrospective gamma dosimetry.

Camel molar tooth enamel response to gamma rays using EPR spectroscopy

Energy Technology Data Exchange (ETDEWEB)

El-Faramawy, N.A.; El-Somany, I. [Ain Shams University, Physics Department, Faculty of Science, Cairo (Egypt); Mansour, A. [National Center for Radiation Research and Technology, Atomic Energy Authority, Cairo (Egypt); Maghraby, A.M.; Eissa, H. [National Institute of Standards (NIS), Ionizing Radiation Metrology Laboratory, Giza (Egypt); Wieser, A. [Helmholtz Zentrum Muenchen-German Research Center for Environmental Health, Department of Radiation Sciences, Institute of Radiation Protection, Neuherberg (Germany)

2018-03-15

Tooth enamel samples from molar teeth of camel were prepared using a combined procedure of mechanical and chemical tooth treatment. Based on electron paramagnetic resonance (EPR) spectroscopy, the dose response of tooth enamel samples was examined and compared to that of human enamel. The EPR dose response of the tooth enamel samples was obtained through irradiation to gamma doses from 1 Gy up to 100 kGy. It was found that the radiation-induced EPR signal increased linearly with gamma dose for all studied tooth enamel samples, up to about 15 kGy. At higher doses, the dose response curve leveled off. The results revealed that the location of the native signal of camel tooth enamel was similar to that of enamel from human molars at 2.00644, but different from that of enamel from cows and goats. In addition, the peak-to-peak width (ΔH{sub pp}) for human and camel molar teeth was similar. It was also found that the response of camel enamel to gamma radiation was 36% lower than that of human enamel. In conclusion, the results indicate the suitability of camel teeth for retrospective gamma dosimetry. (orig.)

Metabolism in tooth enamel and reliability of retrospective EPR dosimetry connected with Chernobyl accident

International Nuclear Information System (INIS)

Brik, A.; Radchuk, V.; Scherbina, O.; Matyash, M.; Gaver, O.

1996-01-01

It is shown that the results of retrospective EPR dosimetry by tooth enamel are essentially determined by the fact that tooth enamel is the mineral of biological origin. The structure of tooth enamel, properties of radiation defects and the role of metabolism in tooth enamel are discussed. It is shown that at deep metamorphic modifications tooth enamel don't save information about its radiation history. The reliability and accuracy of retrospective EPR dosimetry are discussed. Because after Chernobyl accident have passed 10 years the application of tooth enamel for reconstruction of doses which are connected with Chernobyl accident need care and additional investigations

Accuracy and precision of estimating age of gray wolves by tooth wear

Science.gov (United States)

Gipson, P.S.; Ballard, W.B.; Nowak, R.M.; Mech, L.D.

2000-01-01

We evaluated the accuracy and precision of tooth wear for aging gray wolves (Canis lupus) from Alaska, Minnesota, and Ontario based on 47 known-age or known-minimum-age skulls. Estimates of age using tooth wear and a commercial cementum annuli-aging service were useful for wolves up to 14 years old. The precision of estimates from cementum annuli was greater than estimates from tooth wear, but tooth wear estimates are more applicable in the field. We tended to overestimate age by 1-2 years and occasionally by 3 or 4 years. The commercial service aged young wolves with cementum annuli to within ?? 1 year of actual age, but under estimated ages of wolves ???9 years old by 1-3 years. No differences were detected in tooth wear patterns for wild wolves from Alaska, Minnesota, and Ontario, nor between captive and wild wolves. Tooth wear was not appropriate for aging wolves with an underbite that prevented normal wear or severely broken and missing teeth.

The role of Msx1 and Pax9 in pathogenetic mechanisms of tooth agenesis

Directory of Open Access Journals (Sweden)

Yani Corvianindya Rahayu

2009-09-01

Full Text Available Background: Tooth agenesis is one of the most common developmental anomalies in human, which one or a few teeth are absent because they have never formed, may cause cosmetic or occlusal harm, while severe agenesis which are relatively rare require clinical attention to support and maintain the dental function. Molecular studies have demonstrated that tooth development is under strict genetic control. Purpose: This article want to review the genetic regulating that are responsible for tooth agenesis especially the role of Msx1 and Pax9 in pathogenetic mechanisms of tooth agenesis. Review: Tooth agenesis is a consequence of a qualitatively or quantitatively impaired function of genetic networks, which regulate tooth development. Mutations in Msx1 and Pax9 genes are dominant for tooth agenesis in humans. The Pax9 gene, which codes for a paired domain-containing transcription factor that plays an essential role in the development of mammal dentition, has been associated with selective tooth agenesis in humans and mice. Conclusion: Reduced amount of functional Msx1 or Pax9 protein in the tooth forming cells is able to cause severe and selective tooth agenesis. There are differences in the frequency of agenesis of specific teeth associated with the defects in Msx1 and defects in Pax9.

Anthropology, tooth wear, and occlusion ab origine.

Science.gov (United States)

Young, W G

1998-11-01

The purpose of this essay is to emphasize that anthropology, the study of man in his environments, is a potent tool for scientific discovery and inspiration in dental science. It attempts to capture flashes of creative anthropological insight which have illuminated studies of tooth wear and occlusion in the past. While it documents contributions, understandings, and misunderstandings from Australian and New Zealand dentists, it is not a hagiography. The real saint of this essay is the Australian aborigine. For when men and women are understood in their environments, much is learned from them which challenges preconceptions of our dental science culture. The essay concludes that new, contemporary Australian culture needs to be studied by anthropological approaches if we are to understand how dental erosion is exacerbating tooth wear and damaging the occlusions of contemporary Australians. Much remains to be discovered about contemporary lifestyles, habits, and diets that lead to dental erosion, the principal cause of contemporary tooth wear in this part of the world.

Computer-Assisted Technique for Surgical Tooth Extraction

Directory of Open Access Journals (Sweden)

Hosamuddin Hamza

2016-01-01

Full Text Available Introduction. Surgical tooth extraction is a common procedure in dentistry. However, numerous extraction cases show a high level of difficulty in practice. This difficulty is usually related to inadequate visualization, improper instrumentation, or other factors related to the targeted tooth (e.g., ankyloses or presence of bony undercut. Methods. In this work, the author presents a new technique for surgical tooth extraction based on 3D imaging, computer planning, and a new concept of computer-assisted manufacturing. Results. The outcome of this work is a surgical guide made by 3D printing of plastics and CNC of metals (hybrid outcome. In addition, the conventional surgical cutting tools (surgical burs are modified with a number of stoppers adjusted to avoid any excessive drilling that could harm bone or other vital structures. Conclusion. The present outcome could provide a minimally invasive technique to overcome the routine complications facing dental surgeons in surgical extraction procedures.

Effect of drugs on orthodontic tooth movement

Directory of Open Access Journals (Sweden)

Siti Sarah Aulia Amrullah

2016-06-01

Full Text Available Orthodontic tooth movement is basically a biological response to mechanical forces given to the teeth in orthodontic treatment, which involving the periodontal tissue and alveolar bone, resulting in the release of numerous substances from the dental tissues and surrounding structure. Remodeling changes in periodontal tissues are considered to be essential in effecting orthodontic tooth movement which is the base of orthodontic correction. Molecules produced in various diseased tissues or drugs and nutrients consumed regularly by patients, can influence mechanically stressed periodontal tissue through the circulation and interact with target cell combination of which may be inhibitory, additive or synergize. Medications might have an important influence on the rate of tooth movement, and information on their consumption is essential to adequately discuss treatment planning with patients. Therefore it is imperative to the practitioners being in medical profession, must pay close attention to the drug consumption history of every patient before and during the course of treatment.

Pre-existing Periapical Inflammatory Condition Exacerbates Tooth Extraction–induced BRONJ Lesions in Mice

Science.gov (United States)

Song, Minju; Alshaikh, Abdullah; Kim, Terresa; Kim, Sol; Dang, Michelle; Mehrazarin, Shebli; Shin, Ki-Hyuk; Kang, Mo; Park, No-Hee; Kim, Reuben H.

2016-01-01

Introduction Surgical interventions such as tooth extraction increase a chance of developing osteonecrosis of the jaw (ONJ) in patients receiving bisphosphonates (BPs) for treatment of bone-related diseases. Tooth extraction is often performed to eliminate pre-existing pathological inflammatory conditions that make the tooth unsalvageable; however, the role of such conditions on bisphosphonate-related ONJ (BRONJ) development following tooth extraction is not clearly defined. Here, we examined the effects of periapical periodontitis on tooth extraction-induced BRONJ development in mice. Methods Periapical periodontitis was induced by exposing the pulp of the maxillary first molar for 3 weeks in C57/BL6 mice that were intravenously administered with BP. The same tooth was extracted, and after 3 additional weeks, the mice were harvested for histological, histomorphometric, and histochemical staining analyses. Results Pulp exposure induced periapical radiolucency as demonstrated by increased inflammatory cells, TRAP+ osteoclasts, and bone resorption. When BP was administered, pulp exposure did not induce apical bone resorption despite the presence of inflammatory cells and TRAP+ osteoclasts. While tooth extraction alone induced BRONJ lesions, pulp exposure further increased tooth extraction-induced BRONJ development as demonstrated by the presence of more bone necrosis. Conclusion Our study demonstrates that pre-existing pathological inflammatory condition such as periapical periodontitis is a predisposing factor that may exacerbate BRONJ development following tooth extraction. Our study further provides a clinical implication whereby periapical periodontitis should be controlled before performing tooth extraction in BP-users in order to reduce the risk of developing BRONJ. PMID:27637460

Experience of racism and tooth brushing among pregnant Aboriginal Australians: exploring psychosocial mediators.

Science.gov (United States)

Ben, J; Jamieson, L M; Priest, N; Parker, E J; Roberts-Thomson, K F; Lawrence, H P; Broughton, J; Paradies, Y

2014-09-01

Despite burgeoning evidence regarding the pathways by which experiences of racism influence health outcomes, little attention has been paid to the relationship between racism and oral health-related behaviours in particular. We hypothesised that self-reported racism was associated with tooth brushing, and that this association was mediated by perceived stress and sense of control and moderated by social support. Data from 365 pregnant Aboriginal Australian women were used to evaluate tooth brushing behaviour, sociodemographic factors, psychosocial factors, general health, risk behaviours and racism exposure. Bivariate associations were explored and hierarchical logistic regression models estimated odds ratios (OR) and 95% confidence intervals (CI) for tooth brushing. Perceived stress and sense of control were examined as mediators of the association between self-reported racism and tooth brushing using binary mediation with bootstrapping. High levels of self-reported racism persisted as a risk indicator for tooth brushing (OR 0.51, 95%CI 0.27,0.98) after controlling for significant covariates. Perceived stress mediated the relationship between self-reported racism and tooth brushing: the direct effect of racism on tooth brushing was attenuated, and the indirect effect on tooth brushing was significant (beta coefficient -0.09; bias-corrected 95%CI -0.166,-0.028; 48.1% of effect mediated). Sense of control was insignificant as a mediator of the relationship between racism and tooth brushing. High levels of self-reported racism were associated with non-optimal tooth brushing behaviours, and perceived stress mediated this association among this sample of pregnant Aboriginal women.. Limitations and implications are discussed.

Treatment of a horizontal root-fractured tooth with decoronation procedure: case report

Directory of Open Access Journals (Sweden)

Selen Esin Yoldaş

2016-05-01

Full Text Available INTRODUCTION: Early loss of permanent anterior teeth due to trauma can cause esthetic and functional problems for young patients. In such cases, replacement of the missing tooth with traditional approaches is possible; however such approaches will reduce the chance of the patient to receive an esthetic and consistent treatment in the future. CASE REPORT: A 12-year-old male patient referred to our clinic with a history of trauma. Complicated crown fracture in tooth no.11 and horizontal root fracture in tooth no. 21 was detected. Following root canal treatment, tooth no. 11 was restored with a fiber post and a strip crown. To avoid alveolar bone loss due to early tooth extraction, decoronation procedure, an alternative approach, was applied to tooth no. 21. This procedure consisted of leaving the root fragment inside the alveolar socket following the removal of the crown. For the rehabilitation of the missing crown, a partial removable prosthesis was implemented. The patient was recalled in 6., 12. and 18. months. Within the follow-up period, no reduction in the alveolar bone level was seen. No sign of infection was evident. The remaining root fragment kept on resorbing. Tooth no. 11 remained symptom-free as well. The patient is still being followed. CONCLUSION: Decoronation is essentially a treatment choice for preventing alveolar bone loss in ankylosed teeth considered for extraction. In this case report, decoronation was shown to be a suitable alternative also for a fractured, non-ankylosed tooth.

Erosive and Mechanical Tooth Wear in Viking Age Icelanders.

Science.gov (United States)

Richter, Svend; Eliasson, Sigfus Thor

2017-08-29

(1) Background: The importance of the Icelandic Sagas as a source of information about diet habits in medieval Iceland, and possibly other Nordic countries, is obvious. Extensive tooth wear in archaeological material worldwide has revealed that the main cause of this wear is believed to have been a coarse diet. Near the volcano Hekla, 66 skeletons dated from before 1104 were excavated, and 49 skulls could be evaluated for tooth wear. The purpose of this study was to determine the main causes of tooth wear in light of diet and beverage consumption described in the Sagas; (2) Materials and methods: Two methods were used to evaluate tooth wear and seven for age estimation; (3) Results: Extensive tooth wear was seen in all of the groups, increasing with age. The first molars had the highest score, with no difference between sexes. These had all the similarities seen in wear from a coarse diet, but also presented with characteristics that are seen in erosion in modern Icelanders, through consuming excessive amounts of soft drinks. According to the Sagas, acidic whey was a daily drink and was used for the preservation of food in Iceland, until fairly recently; (4) Conclusions: It is postulated that the consumption of acidic drinks and food, in addition to a coarse and rough diet, played a significant role in the dental wear seen in ancient Icelanders.

Tooth enamel as a naturtal beta dosemeter for bone seeking radionuclides

International Nuclear Information System (INIS)

Wieser, A.; Petzoldt, G.

1996-01-01

EPR dosimetry was done on teeth from residents of villages along the Techa river, Southern Urals, Russia. The residents have a 90 Sr body burden due to massive releases of liquid nuclear waste into the Techa river in the early fifties. A long time after ingestion, strontium is only incorporated into the skeleton and dentine of the adults but not in tooth enamel. Tooth enamel therefore, is measuring the beta dose from the contaminated dentine. Based on experimental data of this study a first approximation of the ingestion dose coefficient of tooth enamel was found to be more than 5 times lower than the value given in ICRP 69 for the bone surface of the skeleton. A similar difference was found earlier for the dose absorbed in tooth enamel and dentine. The result of this study allows the supposition that that the metabolism of strontium is very very similar for tooth dentine and the skeleton. (author)

Tooth loss caused by displaced elastic during simple preprosthetic orthodontic treatment

Science.gov (United States)

Dianiskova, Simona; Calzolari, Chiara; Migliorati, Marco; Silvestrini-Biavati, Armando; Isola, Gaetano; Savoldi, Fabio; Dalessandri, Domenico; Paganelli, Corrado

2016-01-01

The use of elastics to close a diastema or correct tooth malpositions can create unintended consequences if not properly controlled. The American Association of Orthodontists recently issued a consumer alert, warning of “a substantial risk for irreparable damage” from a new trend called “do-it-yourself” orthodontics, consisting of patients autonomously using elastics to correct tooth position. The elastics can work their way below the gums and around the roots of the teeth, causing damage to the periodontium and even resulting in tooth loss. The cost of implants to replace these teeth would well exceed the cost of proper orthodontic care. This damage could also occur in a dental office, when a general dentist tries to perform a simplified orthodontic correction of a minor tooth malposition. The present case report describes a case of tooth loss caused by a displaced intraoral elastic, which occurred during a simple preprosthetic orthodontic treatment. PMID:27672645

Management of Tooth Wear: A Holistic, Dental, Medical, and Mental Healthcare Approach.

Science.gov (United States)

Ahmed, Khaled E

2016-08-01

Tooth wear is a condition that affects a substantial cohort of dental patients. It has a measurable impact on patients' satisfaction, and overall quality of life. Recently, with growing evidence, our understanding of the aetiology, progression, and management of tooth wear has evolved. The paper argues that pathological tooth wear should not be solely considered as a dental condition, but rather a dental manifestation of other mental and medical disorders. As such, successful management of tooth wear, and its underlying aetiology, requires a holistic, multidisciplinary management approach, involving dental, medical, and mental healthcare providers.

Behavioral changes during dental appointments in children having tooth extractions

Directory of Open Access Journals (Sweden)

Mariana Gonzalez Cademartori

2017-01-01

Full Text Available Background: Tooth extractions are associated with anxiety-related situations that can cause behavioral problems in pediatric dental clinics. Aim: We aimed to describe the behavior of children during tooth extraction appointments, compare it to their behavior in preceding and subsequent dental appointments, and assess the behavioral differences according to gender, age, type of dentition, and reason for extraction. Settings and Design: This was a retrospective study based on information obtained from records of children between 6 and 13 years of age who were cared for at the Dentistry School in Pelotas, Brazil. Materials and Methods: Child behavior was assessed during the dental appointment that preceded the tooth extraction, during the tooth extraction appointment, and in the subsequent dental appointment using the Venham Behavior Rating Scale. Statistical Analysis: Results were analyzed using the Pearson Chi-square and McNemar tests. Results: Eighty-nine children were included. Cooperative behavior prevailed in all the dental appointments. The prevalence of “mild/intense protest” was higher in the tooth extraction appointments than in the previous or subsequent dental appointments (P < 0.001. No significant differences in behavior were detected between the type of dentition (primary or permanent teeth, reason for extraction or gender. Conclusion: In this sample of children treated at a dental school, the occurrence of uncooperative behavior was higher during the tooth extraction appointments than in the preceding and subsequent dental appointments.

Dose- and time-dependent effects of clodronate on orthodontic tooth movement

Directory of Open Access Journals (Sweden)

Enita Nakaš

2017-02-01

Full Text Available Orthodontic tooth movement is the result of bone remodeling that occurs in periodontal ligament and alveolar bone tissue as a response to mechanical loading of the tooth. The aim of this study is to investigate the time- and dose-response effects of locally administered clodronate on tooth movement. Sixty Wistar rats were randomly assigned to 4 groups of 15 specimens: E1 - application of 10 mMol of clodronate in 3-day intervals; E2 - application of 2.5 mMol of clodronate in 3-day intervals; E3 - application of 10 mMol of clodronate in 7-day intervals; E4 - application of 2.5 mMol of clodronate in 7-day intervals. A 50 μL clodronate solution was injected into a subperiosteal area to the right maxillary incisor. The left maxillary incisor served as a control, with an injection of saline solution. In 3-day interval application regime, there was no effect of clodronate dosing on tooth movement. In 7-day interval application regime, decreased tooth movement was observed with 10 mMol compared with 2.5 mMol clodronate concentration. However, decreased tooth movement was also observed when 2.5 mMol of clodronate was applied in 7-versus 3-day intervals. Conversely, no difference was observed when 10 mMol concentration was applied in 3- versus 7-day intervals. When clodronate is applied subperiosteally in the root area, it decreases the tooth movement. Tooth movement is impeded by the higher clodronate dosing, as well as by shorter application interval even with lower dosing. The purpose of future trials should, therefore, be to determine a safe therapeutic dose/interval application of clodronate in humans and their potential side effects.

Tooth Fracture Detection in Spiral Bevel Gears System by Harmonic Response Based on Finite Element Method

OpenAIRE

Chen, Yuan; Zhu, Rupeng; Jin, Guanghu; Xiong, Yeping

2017-01-01

Spiral bevel gears occupy several advantages such as high contact ratio, strong carrying capacity, and smooth operation, which become one of the most widely used components in high-speed stage of the aeronautical transmission system. Its dynamic characteristics are addressed by many scholars. However, spiral bevel gears, especially tooth fracture occurrence and monitoring, are not to be investigated, according to the limited published issues. Therefore, this paper establishes a three-dimensio...

EPR dosimetry with tooth enamel: A review

International Nuclear Information System (INIS)

Fattibene, Paola; Callens, Freddy

2010-01-01

When tooth enamel is exposed to ionizing radiation, radicals are formed, which can be detected using electron paramagnetic resonance (EPR) techniques. EPR dosimetry using tooth enamel is based on the (presumed) correlation between the intensity or amplitude of some of the radiation-induced signals with the dose absorbed in the enamel. In the present paper a critical review is given of this widely applied dosimetric method. The first part of the paper is fairly fundamental and deals with the main properties of tooth enamel and some of its model systems (e.g., synthetic apatites). Considerable attention is also paid to the numerous radiation-induced and native EPR signals and the radicals responsible for them. The relevant methods for EPR detection, identification and spectrum analyzing are reviewed from a general point of view. Finally, the needs for solid-state modelling and studies of the linearity of the dose response are investigated. The second part is devoted to the practical implementation of EPR dosimetry using enamel. It concerns specific problems of preparation of samples, their irradiation and spectrum acquisition. It also describes how the dosimetric signal intensity and dose can be retrieved from the EPR spectra. Special attention is paid to the energy dependence of the EPR response and to sources of uncertainties. Results of and problems encountered in international intercomparisons and epidemiological studies are also dealt with. In the final section the future of EPR dosimetry with tooth enamel is analyzed.

[Establishment of database with standard 3D tooth crowns based on 3DS MAX].

Science.gov (United States)

Cheng, Xiaosheng; An, Tao; Liao, Wenhe; Dai, Ning; Yu, Qing; Lu, Peijun

2009-08-01

The database with standard 3D tooth crowns has laid the groundwork for dental CAD/CAM system. In this paper, we design the standard tooth crowns in 3DS MAX 9.0 and create a database with these models successfully. Firstly, some key lines are collected from standard tooth pictures. Then we use 3DS MAX 9.0 to design the digital tooth model based on these lines. During the design process, it is important to refer to the standard plaster tooth model. After some tests, the standard tooth models designed with this method are accurate and adaptable; furthermore, it is very easy to perform some operations on the models such as deforming and translating. This method provides a new idea to build the database with standard 3D tooth crowns and a basis for dental CAD/CAM system.

A simple rule governs the evolution and development of hominin tooth size.

Science.gov (United States)

Evans, Alistair R; Daly, E Susanne; Catlett, Kierstin K; Paul, Kathleen S; King, Stephen J; Skinner, Matthew M; Nesse, Hans P; Hublin, Jean-Jacques; Townsend, Grant C; Schwartz, Gary T; Jernvall, Jukka

2016-02-25

The variation in molar tooth size in humans and our closest relatives (hominins) has strongly influenced our view of human evolution. The reduction in overall size and disproportionate decrease in third molar size have been noted for over a century, and have been attributed to reduced selection for large dentitions owing to changes in diet or the acquisition of cooking. The systematic pattern of size variation along the tooth row has been described as a 'morphogenetic gradient' in mammal, and more specifically hominin, teeth since Butler and Dahlberg. However, the underlying controls of tooth size have not been well understood, with hypotheses ranging from morphogenetic fields to the clone theory. In this study we address the following question: are there rules that govern how hominin tooth size evolves? Here we propose that the inhibitory cascade, an activator-inhibitor mechanism that affects relative tooth size in mammals, produces the default pattern of tooth sizes for all lower primary postcanine teeth (deciduous premolars and permanent molars) in hominins. This configuration is also equivalent to a morphogenetic gradient, finally pointing to a mechanism that can generate this gradient. The pattern of tooth size remains constant with absolute size in australopiths (including Ardipithecus, Australopithecus and Paranthropus). However, in species of Homo, including modern humans, there is a tight link between tooth proportions and absolute size such that a single developmental parameter can explain both the relative and absolute sizes of primary postcanine teeth. On the basis of the relationship of inhibitory cascade patterning with size, we can use the size at one tooth position to predict the sizes of the remaining four primary postcanine teeth in the row for hominins. Our study provides a development-based expectation to examine the evolution of the unique proportions of human teeth.

Tooth microwear formation rate in Gasterosteus aculeatus.

Science.gov (United States)

Baines, D C; Purnell, M A; Hart, P J B

2014-05-01

Tooth microwear feature densities were significantly increased in a population of laboratory-reared three-spined stickleback Gasterosteus aculeatus in four days, after they were transferred from a limnetic feeding regime to a benthic feeding regime. These results show that even in aquatic vertebrates with non-occluding teeth, changes in feeding can cause changes in tooth microwear in just a few days, as in mammals. © 2014 The Authors. Journal of Fish Biology published by John Wiley & Sons Ltd on behalf of The Fisheries Society of the British Isles.

Apical Revascularization after Delayed Tooth Replantation: An Unusual Case

Directory of Open Access Journals (Sweden)

Marília Pacífico Lucisano

2016-01-01

Full Text Available The aim of this paper is to present the clinical and radiological outcome of the treatment involving a delayed tooth replantation after an avulsed immature permanent incisor, with a follow-up of 1 year and 6 months. An 8-year-old boy was referred after dental trauma that occurred on the previous day. The permanent maxillary right central incisor (tooth 11 had been avulsed. The tooth was hand-held during endodontic therapy and an intracanal medication application with calcium hydroxide-based paste was performed. An apical plug with mineral trioxide aggregate (MTA was introduced into the apical portion of the canal. When the avulsed tooth was replanted with digital pressure, a blood clot had formed within the socket, which moved the MTA apical plug about 2 mm inside of the root canal. These procedures developed apical revascularization, which promoted a successful endodontic outcome, evidenced by apical closure, slight increase in root length, and absence of signs of external root resorption, during a follow-up of 1 year and 6 months.

The randomized shortened dental arch study: tooth loss over five years.

Science.gov (United States)

Walter, M H; Hannak, W; Kern, M; Mundt, T; Gernet, W; Weber, A; Wöstmann, B; Stark, H; Werner, D; Hartmann, S; Range, U; Jahn, F; Passia, N; Pospiech, P; Mitov, G; Brückner, J; Wolfart, S; Busche, E; Luthardt, R G; Heydecke, G; Marré, B

2013-04-01

The study was designed to provide clinical outcome data for two treatments of the shortened dental arch (SDA). In a multicenter randomized controlled clinical trial, patients with complete molar loss in one jaw were provided with either a partial removable dental prosthesis (PRDP) retained with precision attachments or treated according to the SDA concept preserving or restoring a premolar occlusion. No implants were placed. The primary outcome was tooth loss. Of 152 treated patients, 132 patients reached the 5-year examination. Over 5 years, 38 patients experienced tooth loss. For the primary outcome tooth loss, the Kaplan-Meier survival rates at 5 years were 0.74 (95% CI 0.64, 0.84) in the PRDP group and 0.74 (95% CI 0.63, 0.85) in the SDA group. For tooth loss in the study jaw, the survival rates at 5 years were 0.88 (95% CI 0.80, 0.95) in the PRDP group and 0.84 (95% CI 0.74, 0.93) in the SDA group. The differences were not significant. No Cox regression models of appropriate fit explaining tooth loss on the patient level could be found. The overall treatment goals of a sustainable oral rehabilitation and the avoidance of further tooth loss over longer periods were not reliably achievable. The influence of the type of prosthetic treatment on tooth loss might have been overestimated. Regarding our results, the patient's view will gain even more importance in the clinical decision between removable and fixed restorations in SDAs.

Minimum intervention dentistry and the management of tooth wear in general practice.

Science.gov (United States)

Meyers, I A

2013-06-01

The incidence of tooth wear, or non-carious tooth surface loss (NCTSL), is increasing and oral rehabilitation of patients with non-carious tooth loss requires strategies that address all the factors relevant to the aetiology and pathogenesis of the condition. The multifactorial nature of tooth wear and the variability in its clinical presentation provides treatment challenges for the clinician and successful management must be more than just restoration. Management must include an appropriate mix of preventive and restorative strategies and an understanding that long-term restorative success is affected by the patient's oral environment, and how diet, lifestyle and medical status can modify this environment. Ultimately, the success of any restorative intervention is very dependent on the stability of the oral environment and the condition of the remaining tooth structure. Minimum intervention dentistry (MID) philosophies are ideally suited to tooth wear cases and an overall MID strategy involving diagnosis, recognition and control of predisposing factors, stabilization of the oral environment, remineralization and restoration of the tooth structure, and ongoing maintenance can be implemented. When restorative treatment is required, contemporary materials and techniques are available that can provide cost-effective and conservative restorative alternatives for patients unable to undergo the complex indirect restorative techniques that are both costly and time consuming to implement. These minimally invasive approaches are not only an economically viable solution, but can provide aesthetic and functional rehabilitation and maintain tooth structure as a precursor to more complex restorative options when required. © 2013 Australian Dental Association.

Abalone water-soluble matrix for self-healing biomineralization of tooth defects

Energy Technology Data Exchange (ETDEWEB)

Wen, Zhenliang [Institute of Biomedical and Pharmaceutical Technology, Fuzhou University, Fuzhou 350002 (China); Chen, Jingdi, E-mail: ibptcjd@fzu.edu.cn [Institute of Biomedical and Pharmaceutical Technology, Fuzhou University, Fuzhou 350002 (China); Wang, Hailiang [The Affiliated Stomatological Hospital, Fujian Medical University, Fuzhou 350002 (China); Zhong, Shengnan; Hu, Yimin; Wang, Zhili [Institute of Biomedical and Pharmaceutical Technology, Fuzhou University, Fuzhou 350002 (China); Zhang, Qiqing, E-mail: zhangqiq@126.com [Institute of Biomedical and Pharmaceutical Technology, Fuzhou University, Fuzhou 350002 (China); Institute of Biomedical Engineering, Chinese Academy of Medical Science & Peking Union Medical College, Tianjin 300192 (China)

2016-10-01

Enamel cannot heal by itself if damaged. Hydroxyapatite (HAP) is main component of human enamel. Formation of enamel-like materials for healing enamel defects remains a challenge. In this paper, we successfully isolated the abalone water-soluble matrix (AWSM) with 1.53 wt% the abalone water-soluble protein (AWSPro) and 2.04 wt% the abalone water-soluble polysaccharide (AWSPs) from abandoned abalone shell, and self-healing biomineralization of tooth defects was successfully achieved in vitro. Based on X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), hot field emission scanning electron microscopy (HFESEM) and energy dispersive spectrometer (EDS) analysis, the results showed that the AWSM can efficiently induce remineralization of HAP. The enamel-like HAP was successfully achieved onto etched enamel's surface due to the presence of the AWSM. Moreover, the remineralized effect of eroded enamel was growing with the increase of the AWSM. This study provides a solution to the resource waste and environmental pollution caused by abandoned abalone shell, and we provides a new method for self-healing remineralization of enamel defects by AWSM and develops a novel dental material for potential clinical dentistry application. - Graphical abstract: In this paper, we successfully isolated the abalone water-soluble matrix (AWSM) with 1.53 wt% abalone water-soluble protein (AWSPro) and 2.04 wt% abalone water-soluble polysaccharide (AWSPs) from abandoned abalone shell, and self-healing biomineralization of tooth defects was successfully achieved in vitro by self-organized. Display Omitted - Highlights: • Provides a solution to the resource waste and environmental pollution caused by abandoned abalone shell. • The abalone shell water-soluble matrix contains protein and polysaccharide. • The abalone water-soluble matrix can efficiently induce remineralization of HAP by self-organized. • Achieved self-healing biomineralization of tooth defects in

Abalone water-soluble matrix for self-healing biomineralization of tooth defects

International Nuclear Information System (INIS)

Wen, Zhenliang; Chen, Jingdi; Wang, Hailiang; Zhong, Shengnan; Hu, Yimin; Wang, Zhili; Zhang, Qiqing

2016-01-01

Enamel cannot heal by itself if damaged. Hydroxyapatite (HAP) is main component of human enamel. Formation of enamel-like materials for healing enamel defects remains a challenge. In this paper, we successfully isolated the abalone water-soluble matrix (AWSM) with 1.53 wt% the abalone water-soluble protein (AWSPro) and 2.04 wt% the abalone water-soluble polysaccharide (AWSPs) from abandoned abalone shell, and self-healing biomineralization of tooth defects was successfully achieved in vitro. Based on X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), hot field emission scanning electron microscopy (HFESEM) and energy dispersive spectrometer (EDS) analysis, the results showed that the AWSM can efficiently induce remineralization of HAP. The enamel-like HAP was successfully achieved onto etched enamel's surface due to the presence of the AWSM. Moreover, the remineralized effect of eroded enamel was growing with the increase of the AWSM. This study provides a solution to the resource waste and environmental pollution caused by abandoned abalone shell, and we provides a new method for self-healing remineralization of enamel defects by AWSM and develops a novel dental material for potential clinical dentistry application. - Graphical abstract: In this paper, we successfully isolated the abalone water-soluble matrix (AWSM) with 1.53 wt% abalone water-soluble protein (AWSPro) and 2.04 wt% abalone water-soluble polysaccharide (AWSPs) from abandoned abalone shell, and self-healing biomineralization of tooth defects was successfully achieved in vitro by self-organized. Display Omitted - Highlights: • Provides a solution to the resource waste and environmental pollution caused by abandoned abalone shell. • The abalone shell water-soluble matrix contains protein and polysaccharide. • The abalone water-soluble matrix can efficiently induce remineralization of HAP by self-organized. • Achieved self-healing biomineralization of tooth defects in vitro.

Gear Tooth Wear Detection Algorithm

Science.gov (United States)

Delgado, Irebert R.

2015-01-01

Vibration-based condition indicators continue to be developed for Health Usage Monitoring of rotorcraft gearboxes. Testing performed at NASA Glenn Research Center have shown correlations between specific condition indicators and specific types of gear wear. To speed up the detection and analysis of gear teeth, an image detection program based on the Viola-Jones algorithm was trained to automatically detect spiral bevel gear wear pitting. The detector was tested using a training set of gear wear pictures and a blind set of gear wear pictures. The detector accuracy for the training set was 75 percent while the accuracy for the blind set was 15 percent. Further improvements on the accuracy of the detector are required but preliminary results have shown its ability to automatically detect gear tooth wear. The trained detector would be used to quickly evaluate a set of gear or pinion pictures for pits, spalls, or abrasive wear. The results could then be used to correlate with vibration or oil debris data. In general, the program could be retrained to detect features of interest from pictures of a component taken over a period of time.

Charcot-Marie-Tooth disease-linked protein SIMPLE functions with the ESCRT machinery in endosomal trafficking

OpenAIRE

Lee, Samuel M.; Chin, Lih-Shen; Li, Lian

2012-01-01

Mutations in small integral membrane protein of lysosome/late endosome (SIMPLE) cause autosomal dominant, Charcot-Marie-Tooth disease (CMT) type 1C. The cellular function of SIMPLE is unknown and the pathogenic mechanism of SIMPLE mutations remains elusive. Here, we report that SIMPLE interacted and colocalized with endosomal sorting complex required for transport (ESCRT) components STAM1, Hrs, and TSG101 on early endosomes and functioned with the ESCRT machinery in the control of endosome-to...

Moessbauer Studies of Stannous Fluoride Reactivity with Synthetic Tooth Enamel - A Model for the Tooth Cavity Protection Actions of Novel Dentifrices

International Nuclear Information System (INIS)

Denes, Georges; Muntasar, Abdualhafeed; Kozak, Kathy M.; Baig, Arif A.; White, Donald J.

2002-01-01

SnF 2 is an important toothpaste ingredient, added for the provision of clinical efficacy for hard and soft tissue diseases and in breath protection. Synthetic calcium hydroxyapatite powders were exposed to liquid supernates (25 w/w% toothpaste water slurries, centrifuged) of Crest Gum Care (registered) (SnF 2 ) dentifrice. One-minute treatments were followed by 3x water washing, centrifugation and lyophilization. Post treatment, powders were analyzed by Moessbauer spectroscopy with 0.5-1 gram of treated apatite powder. Results show that tooth mineral stannous fluoride interactions include: (1) formation of surface reaction products with both Sn(II) and Sn(IV) oxidation states; (2) Sn-F binding on mineral surfaces with no evidence of SnO. The surface binding is, however, not pure Sn-F but contains contributions of other ligands, probably oxygens from surface phosphates or hydroxyl groups. Results also suggest that surface reacted stannous tin is oxidized with time, even when bound as a layer on the tooth surface. This study demonstrates for the first time the presence of Sn-F on tooth enamel post treatment and the contribution of passivation to long term stannous chemistry on tooth surfaces. The study also illustrates the practical applications of the Moessbauer technique.

Erosive tooth wear in children

NARCIS (Netherlands)

Carvalho, T.S.; Lussi, A.; Jaeggi, T.; Gambon, D.L.; Lussi, A.; Ganss, C.

2014-01-01

Erosive tooth wear in children is a common condition. Besides the anatomical differences between deciduous and permanent teeth, additional histological differences may influence their susceptibility to dissolution. Considering laboratory studies alone, it is not clear whether deciduous teeth are

Tooth brushing, tongue cleaning and snacking behaviour of dental technology and therapist students

Directory of Open Access Journals (Sweden)

Clement C. Azodo

2010-08-01

Full Text Available Objective: To determine the tooth brushing, tongue cleaning and snacking behaviour of dental technology and therapist students. Methods: A descriptive cross-sectional study of students of Federal School of Dental Therapy and Technology Enugu, Nigeria. Self-administered questionnaire was used to obtain information on demography, frequency, duration and technique of tooth brushing and tongue cleaning as well as information on consumption of snacks. Results: A total of 242 students responded. Dental technology students made up 52.5% of the respondents and dental therapist in training made up 47.5%. Majority (63.2% of the respondents considered the strength of tooth brush when purchasing a tooth brush and 78.9% use tooth brushes with medium strength. Seven-tenth (71.9% of the respondents brush their teeth twice daily and 52.1% brush for 3–5 minutes. About one-third (30.2% brush their teeth in front of a mirror. Chewing stick was used by 51.7% of respondents in addition to the use of tooth brush. Tongue cleaning was done by 94.2% with only 9.5% using a tongue cleaner. Only 20.2% reported regular snacks consumption. Nine-tenth (90.4% of respondents were previously involved in educating others, apart from their colleagues, on tooth brushing. Conclusion: This survey revealed that most of the dental therapy and technology students had satisfactory tooth-brushing behaviour. The zeal to educate others about proper tooth brushing revealed in this study suggests that the students may be helpful in oral health promotion.

Energy harvesting from mastication forces via a smart tooth

Science.gov (United States)

Bani-Hani, Muath; Karami, M. Amin

2016-04-01

The batteries of the current pacing devices are relatively large and occupy over 60 percent of the size of pulse generators. Therefore, they cannot be placed in the subtle areas of human body. In this paper, the mastication force and the resulting tooth pressure are converted to electricity. The pressure energy can be converted to electricity by using the piezoelectric effect. The tooth crown is used as a power autonomous pulse generator. We refer to this envisioned pulse generator as the smart tooth. The smart tooth is in the form of a dental implant. A piezoelectric vibration energy harvester is designed and modeled for this purpose. The Piezoelectric based energy harvesters investigated and analyzed in this paper initially includes a single degree of freedom piezoelectric based stack energy harvester which utilizes a harvesting circuit employing the case of a purely resistive circuit. The next step is utilizing and investigating a bimorph piezoelectric beam which is integrated/embedded in the smart tooth implant. Mastication process causes the bimorph beam to buckle or return to unbuckled condition. The transitions results in vibration of the piezoelectric beam and thus generate energy. The power estimated by the two mechanisms is in the order of hundreds of microwatts. Both scenarios of the energy harvesters are analytically modeled. The exact analytical solution of the piezoelectric beam energy harvester with Euler-Bernoulli beam assumptions is presented. The electro-mechanical coupling and the geometric nonlinearities have been included in the model for the piezoelectric beam.

Root canal treatment of mandibular second premolar tooth with taurodontism

Directory of Open Access Journals (Sweden)

Vujašković Mirjana

2008-01-01

Full Text Available INTRODUCTION Taurodontism is a morphoanatomical change in the shape of a tooth. An enlarged body of a tooth with smaller than usual roots is a characteristic feature. Internal tooth anatomy correlates with this appearance, which means that a taurodontal tooth has a large pulp chamber and apically positioned furcations. This dental anomaly may be associated with different syndromes and congenital discoders. CASE OUTLINE The case report presents the patient of a rare case of taurodontism in the mandibular second premolar with chronic periodontitis. Endodontic treatment was performed after dental history and clinical examination. Special care is required in all segments of endodontic treatment of a taurodontal tooth from the identification orifice, canal exploration, determining working length, cleaning and shaping and obturation of the root canal. Precurved K-file was used for canal exploration and location of the furcation. One mesial and one distal canal with the buccal position were identified in the apical third of the root canal. The working lengths of two canals were determined by radiographic interpretation with two K-files in each canal and verified with the apex locator. During canal instrumentation, the third canal was located in the disto-lingual position. The working length of the third canal was established using the apex locator. CONCLUSION Thorough knowledge of tooth anatomy and its variations can lead to lower percentage of endodontic failure. Each clinical case involving these teeth should be investigated carefully, clinically and radiographically to detect additional root canals. High quality radiographs from different angles and proper instrumentarium improve the quality of endodontic procedure.

Orthodontic tooth movement with clear aligners.

Science.gov (United States)

Drake, Carl T; McGorray, Susan P; Dolce, Calogero; Nair, Madhu; Wheeler, Timothy T

2012-01-01

Clear aligners provide a convenient model to measure orthodontic tooth movement (OTM). We examined the role of in vivo aligner material fatigue and subject-specific factors in tooth movement. Fifteen subjects seeking orthodontic treatment at the University of Florida were enrolled. Results were compared with data previously collected from 37 subjects enrolled in a similar protocol. Subjects were followed prospectively for eight weeks. An upper central incisor was programmed to move 0.5 mm. every two weeks using clear aligners. A duplicate aligner was provided for the second week of each cycle. Weekly polyvinyl siloxane (PVS) impressions were taken, and digital models were fabricated to measure OTM. Initial and final cone beam computed tomography (CBCT) images were obtained to characterize OTM. Results were compared to data from a similar protocol, where subjects received a new aligner biweekly. No significant difference was found in the amount of OTM between the two groups, with mean total OTM of 1.11 mm. (standard deviation (SD) 0.30) and 1.07 mm. (SD 0.33) for the weekly aligner and biweekly control groups, respectively (P = 0.72). Over eight weeks, in two-week intervals, material fatigue does not play a significant role in the rate or amount of tooth movement.

Monte Carlo modeling of human tooth optical coherence tomography imaging

International Nuclear Information System (INIS)

Shi, Boya; Meng, Zhuo; Wang, Longzhi; Liu, Tiegen

2013-01-01

We present a Monte Carlo model for optical coherence tomography (OCT) imaging of human tooth. The model is implemented by combining the simulation of a Gaussian beam with simulation for photon propagation in a two-layer human tooth model with non-parallel surfaces through a Monte Carlo method. The geometry and the optical parameters of the human tooth model are chosen on the basis of the experimental OCT images. The results show that the simulated OCT images are qualitatively consistent with the experimental ones. Using the model, we demonstrate the following: firstly, two types of photons contribute to the information of morphological features and noise in the OCT image of a human tooth, respectively. Secondly, the critical imaging depth of the tooth model is obtained, and it is found to decrease significantly with increasing mineral loss, simulated as different enamel scattering coefficients. Finally, the best focus position is located below and close to the dental surface by analysis of the effect of focus positions on the OCT signal and critical imaging depth. We anticipate that this modeling will become a powerful and accurate tool for a preliminary numerical study of the OCT technique on diseases of dental hard tissue in human teeth. (paper)

Elderly complete denture wearers: a social approach to tooth loss.

Science.gov (United States)

Papadaki, Eftychia; Anastassiadou, Vassiliki

2012-06-01

To correlate emotional reactions to tooth loss with denture satisfaction attributes in elderly complete denture wearers. Total tooth loss is a serious life event, and poor oral health has an impact on daily life. Edentulism treated by rehabilitation with dentures can have a positive effect on patients' self-image and social behaviour. A group of 80 edentulous subjects undergoing routine prosthetic care in a Greek Department of Prosthetic Dentistry were interviewed using two structured questionnaires. The first questionnaire explored reactions to tooth loss, whereas the second measured their subjective experience of complete dentures. The responses to both questionnaires were compared using the statistical package SPSS v.17. The results showed significant correlation between aspects of tooth loss experience and complete denture satisfaction. Despite the fact that a substantial proportion of patients were satisfied with their complete dentures, some patients experienced increased social and psychological problems related to their edentulousness and the wearing of complete dentures. The aesthetic and functional aspects of complete dentures affected both patients' social behaviour and self-confidence. Total tooth loss was not only reflected in patient's social behaviour and self-image, but it had a complex and multifaceted impact on satisfaction from complete dentures. © 2011 The Gerodontology Society and John Wiley & Sons A/S.

Kinematics modeling and experimentation of the multi-manipulator tooth-arrangement robot for full denture manufacturing.

Science.gov (United States)

Zhang, Yong-de; Jiang, Jin-gang; Liang, Ting; Hu, Wei-ping

2011-12-01

Artificial teeth are very complicated in shape, and not easy to be grasped and manipulated accurately by a single robot. The method of tooth-arrangement by multi-manipulator for complete denture manufacturing proposed in this paper. A novel complete denture manufacturing mechanism is designed based on multi-manipulator and dental arch generator. Kinematics model of the multi-manipulator tooth-arrangement robot is built by analytical method based on tooth-arrangement principle for full denture. Preliminary experiments on tooth-arrangement are performed using the multi-manipulator tooth-arrangement robot prototype system. The multi-manipulator tooth-arrangement robot prototype system can automatically design and manufacture a set of complete denture that is suitable for a patient according to the jaw arch parameters. The experimental results verified the validity of kinematics model of the multi-manipulator tooth-arrangement robot and the feasibility of the manufacture strategy of complete denture fulfilled by multi-manipulator tooth-arrangement robot.

Outcome of Endodontically Treated Teeth Diagnosed With Cracked Tooth

Science.gov (United States)

2015-06-01

However, variable symptoms complicate the diagnosis (9). In a study of 32 patients presenting with diffuse longstanding orofacial pain eventually...883-92. 22)Byrnjulsen A, Fristad I, Grevstad T, Hals-Kvinnsland I. Incompletely fractured teeth associated with diffuse longstanding orofacial pain ...cracked tooth is highly associated with discomfort. Patients often describe a momentary, sudden, sharp, lancinating pain that results in continuous tooth

Technical Modifications of Tooth-borne Distraction Device for Anterior Maxillary Distraction in Cleft Patients

Directory of Open Access Journals (Sweden)

Dhivakar Selvaraj

2014-01-01

Full Text Available The tooth-borne distractor gained popularity for anterior maxillary distraction because of the effective treatment outcome, no need for external fixation, noninvasive, less chewing difficulty, social tolerance and economical. Tooth-borne distractor device needs modification in terms of maxillary deficiency, tooth position, retained deciduous tooth, and fistula. Hence, we recommend the following modifications in certain circumstances for the successful treatment outcome.

Tooth engineering: searching for dental mesenchymal cells sources.

Directory of Open Access Journals (Sweden)

Laetitia eKeller

2011-03-01

Full Text Available The implantation of cultured re-associations between embryonic dental mesenchymal cells and epithelial cells from mouse molars at ED14 allowed making full teeth with crown, root, periodontal ligament fibers and bone. Although representing valuable tools to set up methodologies embryonic cells are not easily available. This work thus aimed to replace the embryonic cells by dental mesenchymal cell lines or cultured expanded embryonic cells, and to test their ability to mediate tooth development in vitro when re-associated with a competent dental epithelium. Histology, immunostaining and RT-PCR allowed getting complementary sets of results. Two different immortalized cell lines from ED18 dental mesenchyme failed in mediating tooth formation. The potentialities of embryonic dental mesenchymal cells decreased from ED14 to ED16 and were lost at ED18. This is likely related to a change in the mesenchymal cell phenotype and/or populations during development. Attempts to cultivate ED14 or ED16 embryonic dental mesenchymal cells prior to re-association led to the loss of their ability to support tooth development. This was accompanied by a down-regulation of Fgf3 transcription. Supplementation of the culture medium with FGF2 allowed restoring Fgf3 expression, but not the ability of mesenchymal cells to engage in tooth formation. Altogether, these observations suggest that a competent cell population exists in the dental mesenchyme at ED14, progressively decreases during development, and cannot as such be maintained in vitro. This study evidenced the need for specific conditions to maintain the ability of dental mesenchymal cells to initiate whole tooth formation, when re-associated with an odontogenic epithelium. Efforts to improve the culture conditions will have to be combined with attempts to characterize the competent cells within the dental mesenchyme.

Recording and quantification of ultrasonic echolocation clicks from free-ranging toothed whales

DEFF Research Database (Denmark)

Madsen, Peter Teglberg; Wahlberg, Magnus

2007-01-01

Toothed whales produce short, ultrasonic clicks of high directionality and source level to probe their environment acoustically. This process, termed echolocation, is to a large part governed by the properties of the emitted clicks. Therefore derivation of click source parameters from free......-ranging animals is of increasing importance to understand both how toothed whales use echolocation in the wild and how they may be monitored acoustically. This paper addresses how source parameters can be derived from free-ranging toothed whales in the wild using calibrated multi-hydrophone arrays and digital...... of discrete versions of toothed whale clicks that are meaningful in a biosonar context....

Dens evaginatus and dens invaginatus in a double tooth: A rare case report

Directory of Open Access Journals (Sweden)

Gaurav Sharma

2015-01-01

Full Text Available The presence of dens invaginatus (DI and dens evaginatus (DE on same tooth is a rare phenomenon. However, when these dental anomalies occur on a double tooth, it becomes an extremely rare phenomenon. The authors report a rare case of DI and DE on fused permanent maxillary central incisor with supernumerary tooth in a 40-year-old male. The present article also focuses on the differentiating fusion from gemination and also reviews preventive and management strategies for tooth with complex dental anatomy.

Diagnostics of power transmissions system with tooth gear

Directory of Open Access Journals (Sweden)

Grzegorz WOJNAR

2008-01-01

Full Text Available This paper presents results of laboratory tests that were aimed at detecting early stages of various faults in toothed wheels by measurement and analysis of transverse vibration speed of the transmission gear shafts. In experimental investigation, cracking of the root tooth and chipping of the tooth were detected. The laser vibrometer Ometron VH300+ was used for non-contact measurement of shaft transversal vibration speed. Gear vibrations were recorded in selected points of gear housing and gear shafts at different speeds and gear loads. Results were analyzed and compared but in this paper is presented only selected examples. This paper shows that on the basis of the transverse vibration speed of transmission gear shafts, it is possible to detect defects at an earlier stage than on the basis of the housing vibration accelerations. In the case of measuring gear shaft vibration velocity, the way of the signal generated by the defect of a gear wheel (or bearing is shortened as well as the influence of composed transmittance of the bearing-gear housing system is eliminated. WV time-frequency analysis and complex continuous wavelet transformations were used for detection. The authors introduced a measure of local tooth damage, which was proportional to the size of damage. The results of research presented in this paperconfirmed that the defect's measure is very sensitive to the development of teeth faults.

Mesenchymal Wnt/β-catenin signaling limits tooth number.

Science.gov (United States)

Järvinen, Elina; Shimomura-Kuroki, Junko; Balic, Anamaria; Jussila, Maria; Thesleff, Irma

2018-02-21

Tooth agenesis is one of the predominant developmental anomalies in humans, usually affecting the permanent dentition generated by sequential tooth formation and, in most cases, caused by mutations perturbing epithelial Wnt/β-catenin signaling. In addition, loss-of-function mutations in the Wnt feedback inhibitor AXIN2 lead to human tooth agenesis. We have investigated the functions of Wnt/β-catenin signaling during sequential formation of molar teeth using mouse models. Continuous initiation of new teeth, which is observed after genetic activation of Wnt/β-catenin signaling in the oral epithelium, was accompanied by enhanced expression of Wnt antagonists and a downregulation of Wnt/β-catenin signaling in the dental mesenchyme. Genetic and pharmacological activation of mesenchymal Wnt/β-catenin signaling negatively regulated sequential tooth formation, an effect partly mediated by Bmp4. Runx2 , a gene whose loss-of-function mutations result in sequential formation of supernumerary teeth in the human cleidocranial dysplasia syndrome, suppressed the expression of Wnt inhibitors Axin2 and Drapc1 in dental mesenchyme. Our data indicate that increased mesenchymal Wnt signaling inhibits the sequential formation of teeth, and suggest that Axin2 / Runx2 antagonistic interactions modulate the level of mesenchymal Wnt/β-catenin signaling, underlying the contrasting dental phenotypes caused by human AXIN2 and RUNX2 mutations. © 2018. Published by The Company of Biologists Ltd.

On optimization of internal/external spur gears tooth bending strength

DEFF Research Database (Denmark)

Pedersen, Niels Leergaard

2014-01-01

level at the tooth root. As with most machine elements the design/geometry is defined in standards (ISO). The present work focuses on changing the tooth root design of both external and internal gears, in order to improve the stress concentration factor. The design changes made are compliant...

Incisal tooth wear and self-reported TMD pain in children and adolescents.

Science.gov (United States)

Hirsch, Christian; John, Mike T; Lobbezoo, Frank; Setz, Juergen M; Schaller, Hans-Guenter

2004-01-01

Incisal tooth wear may be a sign of long-term bruxing behavior. Bruxism is purported to be a risk factor for temporomandibular disorders (TMD). The aim of this population-based cross-sectional study was to determine if anterior tooth wear is associated with the self-report of TMD pain in children and adolescents. In a population sample of 1,011 children and adolescents (mean age 13.1 years, range 10 to 18 years; female 52%; response rate 85%), TMD cases were defined as subjects reporting pain in the face, jaw muscles, and temporomandibular joint during the last month according to RDC/TMD. All other subjects were considered controls. Incisal tooth wear was assessed in the clinical examination using a 0 to 2 scale (no wear, enamel wear, dentin wear) for every anterior permanent tooth. The mean wear score for the individuals was categorized into 0, 0.01 to 0.20, 0.21 to 0.40, and 0.41+. A multiple logistic regression analysis, controlling for the effects of age and gender, analyzed the association between the categorized summary wear score and TMD. Specifically, the hypothesis of a trend between higher tooth wear scores and higher risk of TMD was tested. An odds ratio of 1.1 indicated, after adjusting for gender and age, no statistically significantly higher risk of TMD pain with higher tooth wear scores. Incisal tooth wear was not associated with self-reported TMD pain in 10- to 18-year-old subjects.

A comparison of tooth structure in Neanderthals and early Homo sapiens sapiens: a radiographic study.

OpenAIRE

Zilberman, U; Smith, P

1992-01-01

Tooth components of 1st and 2nd erupted permanent molars were measured from standardised radiographs of Homo sapiens sapiens and Homo sapiens neanderthalensis. Enamel height was greater in Homo sapiens sapiens but pulp height and width and the height of the enamel to floor of the pulp chamber were greater in Homo sapiens neanderthalensis. Dentine height, crown width and enamel width showed similar results in the two groups. Unerupted first molars were measured to analyse the influence of func...

Unique case of a geminated supernumerary tooth with trifid crown

International Nuclear Information System (INIS)

Ather, Amber; Ather, Hunaiza; Sheth, Sanket Milan; Muliya, Vidya Saraswathi

2012-01-01

Gemination, a relatively uncommon dental anomaly, is characterized by its peculiar representation as a tooth with a bifid crown and a common root and root canal. It usually occurs in primary dentition. To come across gemination in a supernumerary tooth is a rare phenomenon. The purpose of this paper is to present a unique case of hyperdontia wherein gemination in an impacted supernumerary tooth resulted in a trifid crown unlike the usual bifid crown. The role of conventional radiographs as well as computed tomography, to accurately determine the morphology and spatial location, and to arrive at a diagnosis, is also emphasized in this paper.

A theropod tooth from the Late Triassic of southern Africa

Indian Academy of Sciences (India)

An isolated, large recurved and finely serrated tooth found associated with the prosauropod Euskelosaurus from the Late Triassic part of the Elliot Formation is described here. It is compared to the Triassic thecodonts and carnivorous dinosaurs and its possible affinity is discussed. The tooth possibly belongs to a basal ...

Assessment of the progression of tooth wear on dental casts

NARCIS (Netherlands)

Vervoorn-Vis, G.M.G.J.; Wetselaar, P.; Koutris, M.; Visscher, C.M.; Evälahti, M.; Ahlberg, J.; Lobbezoo, F.

2015-01-01

Many methods are available for the grading of tooth wear, but their ability to assess the progression of wear over time has not been studied frequently. The aim was to assess whether the occlusal/incisal grading scale of the Tooth Wear Evaluation System (TWES) was sensitive enough for the detection

Tooth apatite as a bone substitute: an experimental study and clinical applications

International Nuclear Information System (INIS)

Eun-Seok Kim; Pill-Hoon Choung

1999-01-01

The purpose of this study is to evaluate the usefulness of calcined teeth powder as biological apatite. The animal experiment was performed in 36 rabbits aging 6 weeks and weighing 1.6 kg. In experimental group, tooth apatite powder was implanted to 10 mm bony defects in diameter made on the cranial bone of the rabbits. As control groups, synthetic porous hydroxyapatite and resorbable type calcium carbonate were implanted to the defects of same size. Each group was sacrificed in 1, 2, 4, 6, 8, 12 weeks after the surgery. Specimens were prepared for decalcified samples and observed by a light microscope. And we also performed quantitative analysis of new bone formation through image analysis using computer. In clinical applications, we used tooth apatite alone or mixed with decalcified freeze-dried bone for reconstruction of bony defects in 15 patients undergone enucleation of cyst or ameloblastoma. The obtained results were as follows; 1) The powder of the calcined teeth was called as 'tooth apatite' and it seemed to have biocompatibility in rabbits and human. 2) In group of tooth apatite, after 4 weeks of operation, new bone directly bonded to the particles was observed. And in 12 weeks of it, new bone occupied most of the bony defects. In 6 weeks, resorption of the tooth apatite particles was observed. Thus the tooth apatite was regarded as one of resorbable apatite. 3) The group of tooth apatite showed new bone formation similar to the group of porous hydroxyapatite, but they were inferior to the group of resorbable calcium carbonate. 4) In clinical application, tooth apatite had biocompatibility and new bone formation was observed without any complication except for 1 case. So we think it is a useful bone substitute with osteoconductivity

Effect of Orthodontic Tooth Movement on Salivary Aspartate Aminotransferase Activity

Directory of Open Access Journals (Sweden)

Steiven Adhitya

2013-07-01

Full Text Available 72 1024x768 Aspartate aminotransferase is one of biological indicator in gingival crevicular fluid (CGF. Force orthodontic application could increase activity of aspartate aminotransferase in CGF. However, the increase activity of aspartate aminotransferase in saliva due to orthodontic force and its correlation between aspartate aminotransferase activity and tooth movement remains unclear. Objectives: To evaluate application orthodontic force on the aspartate aminotransferase activity in saliva based on the duration of force and finding correlation between tooth movement and aspartate aminotransferase activity. Methods: Twenty saliva samples collected before extraction of first premolar, at the time of force application for canine retraction and after force application. The canines retraction used 100 grams of interrupted force (module chain for thirty days. The collection of saliva and the measurement of tooth movement were carried out 1 day, 7 days, 14 days, 21 days, and 28 days after force application. The measurement of aspartate aminotransferase activity in saliva was done using spectrophotometer. Results: Application of orthodontic force influences the salivary aspartate aminotransferase activity (F=25.290, p=0.000. Furthermore, tooth movement correlated with aspartate aminotransferase activity (F=0.429, p=0.000. Conclusion: Aspartate aminotransferase activity could be used as tooth movement indicator that related to the duration of force application.DOI : 10.14693/jdi.v20i1.128

A review of heat transfer in human tooth--experimental characterization and mathematical modeling.

Science.gov (United States)

Lin, Min; Xu, Feng; Lu, Tian Jian; Bai, Bo Feng

2010-06-01

With rapid advances in modern dentistry, high-energy output instruments (e.g., dental lasers and light polymerizing units) are increasingly employed in dental surgery for applications such as laser assisted tooth ablation, bleaching, hypersensitivity treatment and polymerization of dental restorative materials. Extreme high temperature occurs within the tooth during these treatments, which may induce tooth thermal pain (TTP) sensation. Despite the wide application of these dental treatments, the underlying mechanisms are far from clear. Therefore, there is an urgent need to better understand heat transfer (HT) process in tooth, thermally induced damage of tooth, and the corresponding TTP. This will enhance the design and optimization of clinical treatment strategies. This paper presents the state-of-the-art of the current understanding on HT in tooth, with both experimental study and mathematical modeling reviewed. Limitations of the current experimental and mathematical methodologies are discussed and potential solutions are suggested. Interpretation of TTP in terms of thermally stimulated dentinal fluid flow is also discussed. Copyright (c) 2010 Academy of Dental Materials. All rights reserved.

Conversion from tooth enamel dose to organ doses for electron spin resonance dosimetry

International Nuclear Information System (INIS)

Takahashi, Fumiaki; Yamaguchi, Yasuhiro; Saito, Kimiaki; Hamada, Tatsuji

2002-01-01

Conversion from tooth enamel dose to organ doses was analyzed to establish a method of retrospective individual dose assessment against external photon exposure by electron spin resonance (ESR) dosimetry. Dose to tooth enamel was obtained by Monte Carlo calculations using a modified MIRD-type phantom with a teeth part. The calculated tooth enamel doses were verified by measurements with thermo-luminescence dosimeters inserted in a physical head phantom. Energy and angular dependences of tooth enamel dose were compared with those of other organ doses. Additional Monte Carlo calculations were performed to study the effect of human model on the tooth enamel dose with a voxel-type phantom, which was based on computed tomography images of the physical phantom. The data derived with the modified MIRD-type phantom were applied to convert from tooth enamel dose to organ doses against external photon exposure in a hypothesized field, where scattered radiation was taken into account. The results indicated that energy distribution of photons incident to a human body is required to evaluate precisely an individual dose based on ESR dosimetry for teeth. (author)

Clinical management of a fused upper premolar with supernumerary tooth: a case report

Directory of Open Access Journals (Sweden)

Kyu-Min Cho

2014-11-01

Full Text Available n dentistry, the term 'fusion' is used to describe a developmental disorder of dental hard tissues. In the permanent dentition, fusion of a normal tooth and a supernumerary tooth usually involves the incisors or canines. However, a few cases of fusion involving premolars have also been reported to date. We present a rare case in which fusion of the maxillary left second premolar and a supernumerary tooth in a 13-year-old girl was diagnosed using cone beam computed tomography (CBCT, Alphard-3030, Asahi Roentgen Ind. Co., Ltd.. The tooth was bicuspidized after routine nonsurgical root canal treatment, and the separated teeth underwent appropriate restoration procedures. The second premolar and supernumerary tooth remained asymptomatic without any signs of inflammation after a follow-up period of 9 years. Identification of anatomical anomalies is important for treatment in cases involving fusion with supernumerary tooth, and therefore the microscopic examinations and CBCT are essential for the diagnosis. Fused teeth can be effectively managed by the comprehensive treatment which includes both endodontic and periodontal procedures.

Corticotomy affects both the modus and magnitude of orthodontic tooth movement

DEFF Research Database (Denmark)

Verna, Carlalberta; Cattaneo, Paolo; Dalstra, Michel

2017-01-01

OBJECTIVE: To analyze whether the decreased bone density due to the manipulation of bone remodeling rate has an influence on the type of the planned tooth movement. MATERIALS AND METHODS: A finite element model of a lower incisor has been developed. The density of the alveolar bone surrounding th......: A decreased bone density influences not only the amount of tooth movement, but also its type. This study suggests that the moment-to-force ratios used in conventional orthodontics should be modified in case of techniques that decrease bone density to enhance tooth movement rate....

Tooth damage in captive orcas (Orcinus orca).

Science.gov (United States)

Jett, John; Visser, Ingrid N; Ventre, Jeffrey; Waltz, Jordan; Loch, Carolina

2017-12-01

Tooth damage as a result of oral stereotypies is evident in captive orca, yet little research on the topic exists. This study examines the associations between dental pathology, sex, facility, duration of captivity and other factors in captive orca. We evaluated mandibular and maxillary teeth from dental images of 29 captive orca owned by a US-based theme park. Each tooth was scored for coronal wear, wear at or below gum line and bore holes. Fractured and missing teeth were also noted. Summary statistics described the distribution and severity of pathologies; inferential statistics examined how pathologies differed between sexes, between wild-captured and captive-born orcas and between captive orca at four facilities. We also evaluated how dental pathology and duration of captivity were related. Approximately 24% of whales exhibited "major" to "extreme" mandibular coronal tooth wear, with coronal wear and wear at or below gum line highly correlated. More than 60% of mandibular teeth 2 and 3 exhibited fractures. Bore holes were observed primarily among anterior mandibular teeth, with more than 61% of teeth 2 and 3 bearing evidence of having been drilled. Four of five orca with the highest age-adjusted tooth pathology indices were captive-born. Various dental pathologies were observed across all whales, with pathologies beginning at a young age. Oral stereotypies exhibited by captive orca contributed to the observed dental damage. By making dental and health records of captive whales publicly available, the theme park industry is uniquely positioned to provide further insight into dental pathology and resultant health consequences in captive orca. Copyright © 2017 Elsevier Ltd. All rights reserved.

Phenotypic spectrum of dynamin 2 mutations in Charcot-Marie-Tooth neuropathy

NARCIS (Netherlands)

Claeys, Kristl G.; Züchner, Stephan; Kennerson, Marina; Berciano, José; Garcia, Antonio; Verhoeven, Kristien; Storey, Elsdon; Merory, John R.; Bienfait, Henriette M. E.; Lammens, Martin; Nelis, Eva; Baets, Jonathan; de Vriendt, Els; Berneman, Zwi N.; de Veuster, Ilse; Vance, Jefferey M.; Nicholson, Garth; Timmerman, Vincent; de Jonghe, Peter

2009-01-01

Dominant intermediate Charcot-Marie-Tooth neuropathy type B is caused by mutations in dynamin 2. We studied the clinical, haematological, electrophysiological and sural nerve biopsy findings in 34 patients belonging to six unrelated dominant intermediate Charcot-Marie-Tooth neuropathy type B

Ion microprobe U-Pb dating of a dinosaur tooth

International Nuclear Information System (INIS)

Sano, Yuji; Terada, Kentaro; Ly, Chi V.; Park, Eun Ju

2006-01-01

Ion microprobe U-Pb dating of apatite is applied to a fossil tooth of a Allosaurid derived from the Hasandong Formation in the Gyeongsang basin, southeastern Korea. Twelve spots on a single fragment of the fossil dentine yield a Tera-Wasserburg concordia intercept age of 115±10 Ma (2σ, MSWD=0.59) on a 238 U/ 206 Pb- 207 Pb/ 206 Pb- 204 Pb/ 206 Pb diagram. The age provides a constraint on the depositional age of the fossil in its host Hassandong Formation as Early Aptian. The success of the ion microprobe dating depends on the heterogeneities of diagenetically incorporated U and Pb at the few hundred μm scale, the consequent variations in Pb isotopic compositions due to radioactive decay and the closed-system behavior of U and Pb. There are at least three end-members to explain the variations of minor chemical components such as FeO, SiO 2 and Al 2 O 3 , and trace elements as Th, U and rare earth elements (REE) in the sample by a simple mixing model. They are (1) very low minor and REE, very high common Pb with variable U abundances, (2) low common Pb, high minor, REE, and U abundances, and (3) low minor, common Pb, and U with intermediate REE abundances, even though groups (2) and (3) may consist of a larger group. Various contributions of the three (and/or two) end-members during diagenetic processes may cause the elemental fractionation of U and Pb in a fossil tooth. (author)

Three dimensional mathematical model of tooth for finite element analysis

Directory of Open Access Journals (Sweden)

Puškar Tatjana

2010-01-01

Full Text Available Introduction. The mathematical model of the abutment tooth is the starting point of the finite element analysis of stress and deformation of dental structures. The simplest and easiest way is to form a model according to the literature data of dimensions and morphological characteristics of teeth. Our method is based on forming 3D models using standard geometrical forms (objects in programmes for solid modeling. Objective. Forming the mathematical model of abutment of the second upper premolar for finite element analysis of stress and deformation of dental structures. Methods. The abutment tooth has a form of a complex geometric object. It is suitable for modeling in programs for solid modeling SolidWorks. After analyzing the literature data about the morphological characteristics of teeth, we started the modeling dividing the tooth (complex geometric body into simple geometric bodies (cylinder, cone, pyramid,.... Connecting simple geometric bodies together or substricting bodies from the basic body, we formed complex geometric body, tooth. The model is then transferred into Abaqus, a computational programme for finite element analysis. Transferring the data was done by standard file format for transferring 3D models ACIS SAT. Results. Using the programme for solid modeling SolidWorks, we developed three models of abutment of the second maxillary premolar: the model of the intact abutment, the model of the endodontically treated tooth with two remaining cavity walls and the model of the endodontically treated tooth with two remaining walls and inserted post. Conclusion Mathematical models of the abutment made according to the literature data are very similar with the real abutment and the simplifications are minimal. These models enable calculations of stress and deformation of the dental structures. The finite element analysis provides useful information in understanding biomechanical problems and gives guidance for clinical research.

Generation of gear tooth surfaces by application of CNC machines

Science.gov (United States)

Litvin, F. L.; Chen, N. X.

1994-01-01

This study will demonstrate the importance of application of computer numerically controlled (CNC) machines in generation of gear tooth surfaces with new topology. This topology decreases gear vibration and will extend the gear capacity and service life. A preliminary investigation by a tooth contact analysis (TCA) program has shown that gear tooth surfaces in line contact (for instance, involute helical gears with parallel axes, worm gear drives with cylindrical worms, etc.) are very sensitive to angular errors of misalignment that cause edge contact and an unfavorable shape of transmission errors and vibration. The new topology of gear tooth surfaces is based on the localization of bearing contact, and the synthesis of a predesigned parabolic function of transmission errors that is able to absorb a piecewise linear function of transmission errors caused by gear misalignment. The report will describe the following topics: description of kinematics of CNC machines with six degrees of freedom that can be applied for generation of gear tooth surfaces with new topology. A new method for grinding of gear tooth surfaces by a cone surface or surface of revolution based on application of CNC machines is described. This method provides an optimal approximation of the ground surface to the given one. This method is especially beneficial when undeveloped ruled surfaces are to be ground. Execution of motions of the CNC machine is also described. The solution to this problem can be applied as well for the transfer of machine tool settings from a conventional generator to the CNC machine. The developed theory required the derivation of a modified equation of meshing based on application of the concept of space curves, space curves represented on surfaces, geodesic curvature, surface torsion, etc. Condensed information on these topics of differential geometry is provided as well.

Relationship and inter observer agreement of tooth and face forms in a Saudi subpopulation.

Science.gov (United States)

Habib, Syed Rashid; Shiddi, Ibraheem Al; Al-Sufyani, Mohammed D; Althobaiti, Fahad A

2015-04-01

To determine the relationship of tooth form with the face form by different observers and further investigate the inter observer agreement on tooth forms, face forms, their relationship among male Saudis. A comparative cross-sectional study. Department of Prosthodontics, College of Dentistry, King Saud University, Riyadh, KSA, from February till August 2013. Ninety four male participants aged 18 - 35 years were randomly recruited for the study. Full-face and anterior teeth (intraoral) digital photographs in the frontal plane were recorded. The outline tracings of the face and the tooth were obtained using Autocad (version 2010) software. The outline of the tooth was enlarged proportionately, without altering the length to width ratio to fit the face outline. The outlines were then evaluated visually by 6 prosthodontists and results were tabulated. The most common type of face form (49.65%) and tooth form (56.38%) was square tapering. Using the visual method, a good relationship (31.41%), moderate relationship (35.31%), weak relationship (19.68%) and no relationship (13.65%) between the tooth form and face form was found by the observers. Overall kappa for inter observer agreement on face form, tooth form and their relationship was 0.24, 0.17 and 0.26 respectively. The kappa values showed a fair agreement between the observers. The study results indicated that there was no highly defined relationship between the tooth form and face form in the studied Saudi subpopulation. A fair agreement was found between the observers for classifying the tooth forms, face froms and their relationship.

Surgical treatments of the impacted canine tooth in young dogs

International Nuclear Information System (INIS)

Amimoto, A.; Iwamoto, S.; Hachimura, H.; Sasaki, K.; Taura, Y.; Nakama, S.; Yamanouchi, T.

1993-01-01

Surgical treatments of the impacted canine tooth were carried out in 8 young dogs, and the results were successful in 12 out of 14 cases (85.7%). The treatments consisting of surgical correction by immediate tipping movement, fenestration of the gingiva, and removal of the impacted tooth, were applied to 14 cases radiographically showing the immature tooth root and no abnormalities in the tooth root or alveolar bone. Impacted teeth were seen in 8 regions of the maxilla and 6 regions of the mandible. Mesioversion was seen in almost all maxillary impacted teeth, while linguoversion or lingual mesioversion in all mandibular cases. Surgical correction was carried out by immediate tipping movement after removal of the retained deciduous canine with or without resection of the alveolar bone. Fixation of the moved teeth was done using a wedge made from the deciduous canine root, which was driven into the vacant alveolar cavity after moving. An additional fixation using a steel wire and/or self-curing resin was done, if necessary

Enamel subsurface damage due to tooth preparation with diamonds.

Science.gov (United States)

Xu, H H; Kelly, J R; Jahanmir, S; Thompson, V P; Rekow, E D

1997-10-01

In clinical tooth preparation with diamond burs, sharp diamond particles indent and scratch the enamel, causing material removal. Such operations may produce subsurface damage in enamel. However, little information is available on the mechanisms and the extent of subsurface damage in enamel produced during clinical tooth preparation. The aim of this study, therefore, was to investigate the mechanisms of subsurface damage produced in enamel during tooth preparation by means of diamond burs, and to examine the dependence of such damage on enamel rod orientation, diamond particle size, and removal rate. Subsurface damage was evaluated by a bonded-interface technique. Tooth preparation was carried out on two enamel rod orientations, with four clinical diamond burs (coarse, medium, fine, and superfine) used in a dental handpiece. The results of this study showed that subsurface damage in enamel took the form of median-type cracks and distributed microcracks, extending preferentially along the boundaries between the enamel rods. Microcracks within individual enamel rods were also observed. The median-type cracks were significantly longer in the direction parallel to the enamel rods than perpendicular to the rods. Preparation with the coarse diamond bur produced cracks as deep as 84 +/- 30 microns in enamel. Finishing with fine diamond burs was effective in crack removal. The crack lengths in enamel were not significantly different when the removal rate was varied. Based on these results, it is concluded that subsurface damage in enamel induced by tooth preparation takes the form of median-type cracks as well as inter- and intra-rod microcracks, and that the lengths of these cracks are sensitive to diamond particle size and enamel rod orientation, but insensitive to removal rate.

AUTOGENOUS TOOTH TRANSPLANTATION IN ADULT ...

African Journals Online (AJOL)

drclement

ABSTRACT. A case of autotransplantation of a tooth in a 26 year old female African cleft palate patient is reported. This case report emphasizes the possibility and success of autotransplantation in our centre, it also emphasizes that transplantation is only technique sensitive but less equipment sensitive. It further stresses.

Natural Tooth Pontic: An Instant Esthetic Option for Periodontally Compromised Teeth—A Case Series

Directory of Open Access Journals (Sweden)

Rishi Raj

2016-01-01

Full Text Available Sudden tooth loss in the esthetic zone of the maxillary or mandibular anterior region can be due to trauma, periodontal disease, or endodontic failure. The treatment options for replacing the missing tooth can vary between removable prosthesis, tooth-supported prosthesis, and implant-supported prosthesis. Irrespective of the final treatment, the first line of management would be to provisionally restore the patient’s esthetic appearance at the earliest, while functionally stabilizing the compromised arch. Using the patient’s own natural tooth as a pontic offers the benefits of being the right size, shape, and color and provides exact repositioning in its original intraoral three-dimensional position. Additionally, using the patient’s platelet concentrate (platelet rich fibrin facilitates early wound healing and preservation of alveolar ridge shape following tooth extraction. The abutment teeth can also be preserved with minimal or no preparation, thus keeping the technique reversible, and can be completed at the chair side thereby avoiding laboratory costs. This helps the patient better tolerate the effect of tooth loss psychologically. The article describes a successful, immediate, and viable technique for rehabilitation of three different patients requiring replacement of a single periodontally compromised tooth in an esthetic region.

FACTORS RELATED TO TOOTH LOSS AMONG INDUSTRIAL WORKERS IN PHATHUM THANI, THAILAND.

Science.gov (United States)

Jaaidee, Jeerateep; Chatrchaiwiwatana, Supaporn; Ratanasiri, Amornrat

2017-01-01

Tooth loss is an important oral health problem among Thai people. The objectives of this study were to evaluate the prevalence of and factors associated with tooth loss among Thai industrial workers in order to apply preventive oral health programs to this population. The study consisted of 1,500 adults working in Nava Nakorn Industrial Estate, Pathum Thani Province, Thailand in 2014. Probability proportion to size cluster sampling was used and 16 clusters were included in the study. An oral health questionnaire was developed, evaluated for content validity by experts and then given to participants to fill out. The study population consisted of 621 males (41.4%) and 879 females (58.6%) aged between 19-25 years. The overall prevalence of tooth loss was 62.2% and the major reason for tooth loss was dental caries (60%). Results from multivariable logistic regression analysis show that factors associated with tooth loss were: having a history of scaling or tooth cleaning [adjusted odds ratio (AOR)= 2.47; 95% CI: 1.21-4.65], having dental caries with exposed pulp (AOR=4.12; 95% CI: 3.26-7.67), having tooth mobility due to periodontal disease (AOR=2.41; 95% CI: 2.71-5.22), having needed tooth restoration (AOR=1.75; 95% CI: 1.23-2.65), having a history of maxillofacial or a temporo-mandibular joint accident (AOR=2.13; 95% CI: 1.87- 3.23), wearing dentures (AOR=2.58; 95% CI: 2.17-6.72), using dental care services during the previous year (AOR=2.21; 95% CI: 1.26-4.57), eating snacks and candy daily (AOR=2.14; 95% CI: 1.82-2.92), having toothache (AOR=2.64; 95% CI: 1.43- 3.92), having dental caries (AOR=2.23; 95% CI: 1.62-3.27) and having a history of orthodontic treatment (AOR=3.61; 95% CI: 1.84-5.68). The Nagelkerke R squared for the model was 0.42. Our findings suggest several clinical, socio-economic and lifestyle factors are associated with tooth loss among these Thai industrial workers. An appropriate preventive oral health program targeting this high-risk group taking

Reasons for tooth mortality as perceived by dental professionals in ...

African Journals Online (AJOL)

Conclusion: The results of the present study suggest that among the patients attending dental clinics and hospitals in Udaipur city, dental caries and periodontal disease was found to be the two major causes of tooth mortality. This is probably the first study to report on the trends in tooth loss in general practice in Udaipur ...

Prosthetic clone and natural human tooth comparison by speckle interferometry

Science.gov (United States)

Slangen, Pierre; Corn, Stephane; Fages, Michel; Raynal, Jacques; Cuisinier, Frederic J. G.

2010-09-01

New trends in dental prosthodontic interventions tend to preserve the maximum of "body" structure. With the evolution of CAD-CAM techniques, it is now possible to measure "in mouth" the remaining dental tissues. The prosthetic crown is then designed using this shape on which it will be glued on, and also by taking into account the contact surface of the opposite jaw tooth. Several theories discuss on the glue thickness and formulation, but also on the way to evolve to a more biocompatible crown and also new biomechanical concepts. In order to validate these new concepts and materials, and to study the mechanical properties and mechanical integrity of the prosthesis, high resolution optical measurements of the deformations of the glue and the crown are needed. Samples are two intact premolars extracted for orthodontics reasons. The reference sample has no modifications on the tooth while the second sample tooth is shaped to receive a feldspathic ceramic monoblock crown which will be glued. This crown was manufactured with a chairside CAD-CAM system from an intra-oral optical print. The software allows to realize a nearly perfect clone of the reference sample. The necessary space for the glue is also entered with ideal values. This duplication process yields to obtain two samples with identical anatomy for further processing. The glue joint thickness can also be modified if required. The purpose is to compare the behaviour of a natural tooth and its prosthetic clone manufactured with "biomechanical" concepts. Vertical cut samples have been used to deal with planar object observation, and also to look "inside" the tooth. We have developed a complete apparatus enabling the study of the compressive mechanical behaviour of the concerned tooth by speckle interferometry. Because in plane displacements are of great interest for orthodontic measurements1, an optical fiber in-plane sensitive interferometer has been designed. The fibers are wrapped around piezoelectric

In phantom dosimetric response of tooth enamel to neutrons

International Nuclear Information System (INIS)

Fattibene, P.; Angelone, M.; Pillon, M.; De Coste, V.

2004-01-01

Electron Paramagnetic Resonance dosimetry based on tooth enamel has one important application in dose reconstruction of nuclear plant workers, where the contribution of neutrons to individual dose is often important. Evaluation of tooth enamel response to neutrons is thus an important goal. A few experimental data at thermal and fast neutron energies are available. A first evaluation of the tooth enamel relative response to 60 Co in monoenergetic neutron flux of 2.8 and of 14 MeV, published elsewhere, has provided results apparently non-consistent with the results obtained at lower and higher energies. A comparison of those results in the 2.8 and 14 MeV beams with those available in the literature for other beams is reported and possible reasons for incongruities are discussed. Dose conversion factors of enamel to the water and air are also calculated and reported. (authors)

Sodium hyaluronate accelerates the healing process in tooth sockets of rats.

Science.gov (United States)

Mendes, Renato M; Silva, Gerluza A B; Lima, Miguel F; Calliari, Marcelo V; Almeida, Alvair P; Alves, José B; Ferreira, Anderson J

2008-12-01

In this study we evaluated the effects of sodium hyaluronate (HY) in the healing process of tooth sockets of rats. Immediately after the extraction of the upper first molars of male Holtzman rats, right sockets were treated with 1% HY gel (approximately 0.1 ml), while left sockets were used as control (blood clot). The animals were sacrificed at 2, 7, and 21 days after tooth extraction and upper maxillaries processed for histological and morphometric analysis of the apical and medium thirds of the sockets. Carbopol, an inert gel, was used to evaluate the mechanical effect of gel injection into sockets. Expression of bone morphogenetic protein-2 (BMP-2) and osteopontin (OPN) was determined by immunohistochemistry at 1, 2, 3, 4, 5, and 7 days after tooth extraction. Histological analysis showed that HY treatment induced earlier trabecular bone deposition resulting in a bone matrix more organized at 7 and 21 days after tooth extraction. Also, HY elicited significant increase in the amount of bone trabeculaes at 7 and 21 days after tooth extraction (percentage of trabecular bone area at 7 days: 13.21+/-4.66% vs. 2.58+/-1.36% in the apical third of control sockets) and in the vessels counting at 7 days. Conversely, the number of cell nuclei was decreased in HY-treated sockets. Additionally, expression of BMP-2 and OPN was enhanced in HY-treated sockets compared with control sockets. These findings suggest that HY accelerates the healing process in tooth sockets of rats stimulating the expression of osteogenic proteins.

Antagonistic Functions of USAG-1 and RUNX2 during Tooth Development.

Directory of Open Access Journals (Sweden)

Yumiko Togo

Full Text Available Supernumerary teeth and tooth agenesis are common morphological anomalies in humans. We previously obtained evidence that supernumerary maxillary incisors form as a result of the successive development of the rudimentary maxillary incisor tooth germ in Usag-1 null mice. The development of tooth germs is arrested in Runx2 null mice, and such mice also exhibit lingual epithelial buds associated with the upper molars and incisors. The aim of this study is to investigate the potential crosstalk between Usag-1 and Runx2 during tooth development. In the present study, three interesting phenomena were observed in double null Usag-1-/-/Runx2-/- mice: the prevalence of supernumerary teeth was lower than in Usag-1 null mice; tooth development progressed further compared than in Runx2 null mice; and the frequency of molar lingual buds was lower than in Runx2 null mice. Therefore, we suggest that RUNX2 and USAG-1 act in an antagonistic manner. The lingual bud was completely filled with odontogenic epithelial Sox2-positive cells in the Usag-1+/+/Runx2-/- mice, whereas almost no odontogenic epithelial Sox2-positive cells contributed to supernumerary tooth formation in the rudimentary maxillary incisors of the Usag-1-/-/Runx2+/+ mice. Our findings suggest that RUNX2 directly or indirectly prevents the differentiation and/or proliferation of odontogenic epithelial Sox2-positive cells. We hypothesize that RUNX2 inhibits the bone morphogenetic protein (BMP and/or Wnt signaling pathways regulated by USAG-1, whereas RUNX2 expression is induced by BMP signaling independently of USAG-1.

Estimation of Tooth Size Discrepancies among Different Malocclusion Groups

OpenAIRE

Hasija, Narender; Bala, Madhu; Goyal, Virender

2014-01-01

ABSTRACT Regards and Tribute: Late Dr Narender Hasija was a mentor and visionary in the light of knowledge and experience. We pay our regards with deepest gratitude to the departed soul to rest in peace. Bolton’s ratios help in estimating overbite, overjet relationships, the effects of contemplated extractions on posterior occlusion, incisor relationships and identification of occlusal misfit produced by tooth size discrepancies. Aim: To determine any difference in tooth size discrepancy in a...

Interactive effects of periodontitis and orthodontic tooth movement on dental root resorption, tooth movement velocity and alveolar bone loss in a rat model.

Science.gov (United States)

Kirschneck, Christian; Fanghänel, Jochen; Wahlmann, Ulrich; Wolf, Michael; Roldán, J Camilo; Proff, Peter

2017-03-01

Many adult orthodontic patients suffer from chronic periodontitis with recurrent episodes of active periodontal inflammation. As their number is steadily increasing, orthodontists are more and more frequently challenged by respective treatment considerations. However, little is currently known regarding interactive effects on undesired dental root resorption (DRR), tooth movement velocity, periodontal bone loss and the underlying cellular and tissue reactions. A total of 63 male Fischer344 rats were used in three consecutive experiments employing 21 animals each (A/B/C), randomly assigned to 3 experimental groups (n=7, 1/2/3), respectively: (A) CBCT; (B) histology/serology; (C) RT-qPCR-(1) control; (2) orthodontic tooth movement (OTM) of the first/second upper left molars (NiTi coil spring, 0.25N); (3) OTM with experimentally induced periodontitis (cervical silk ligature). After 14days of OTM, we quantified blood leukocyte level, DRR, osteoclast activity and relative gene expression of inflammatory and osteoclast marker genes within the dental-periodontal tissue as well as tooth movement velocity and periodontal bone loss after 14 and 28 days. The experimentally induced periodontal bone loss was significantly increased by concurrent orthodontic force application. Periodontal inflammation during OTM on the other hand significantly augmented the extent of DRR, relative expression of inflammatory/osteoclast marker genes, blood leukocyte level and periodontal osteoclast activity. In addition, contrary to previous studies, we observed a significant increase in tooth movement velocity. Although accelerated tooth movement would be favourable for orthodontic treatment, our results suggest that orthodontic interventions should only be performed after successful systematic periodontal therapy and paused in case of recurrent active inflammation. Copyright © 2016 Elsevier GmbH. All rights reserved.

Canine tooth size and fitness in male mandrills (Mandrillus sphinx).

Science.gov (United States)

Leigh, Steven R; Setchell, Joanna M; Charpentier, Marie; Knapp, Leslie A; Wickings, E Jean

2008-07-01

Sexual selection theory explains the evolution of exaggerated male morphologies and weaponry, but the fitness consequences of developmental and age-related changes in these features remain poorly understood. This long-term study of mandrill monkeys (Mandrillus sphinx) demonstrates how age-related changes in canine tooth weaponry and adult canine size correlate closely with male lifetime reproductive success. Combining long-term demographic and morphometric data reveals that male fitness covaries simply and directly with canine ontogeny, adult maximum size, and wear. However, fitness is largely independent of other somatometrics. Male mandrills sire offspring almost exclusively when their canines exceed approximately 30 mm, or two-thirds of average adult value (45 mm). Moreover, sires have larger canines than nonsires. The tooth diminishes through wear as animals age, corresponding with, and perhaps influencing, reproductive senescence. These factors combine to constrain male reproductive opportunities to a brief timespan, defined by the period of maximum canine length. Sexually-selected weaponry, especially when it is nonrenewable like the primate canine tooth, is intimately tied to the male life course. Our analyses of this extremely dimorphic species indicate that sexual selection is closely intertwined with growth, development, and aging, pointing to new directions for sexual selection theory. Moreover, the primate canine tooth has potential as a simple mammalian system for testing genetically-based models of aging. Finally, the tooth may record details of life histories in fossil primates, especially when sexual selection has played a role in the evolution of dimorphism.

Ancient DNA: Saber-Toothed Cats Are the Same Beasts After All.

Science.gov (United States)

Meachen, Julie A

2017-11-06

Ancient DNA from the saber-toothed cat Homotherium reveals that the late Pleistocene species from Europe and North America were the same. Homotherium turns out to be only distantly related to the well-known saber-toothed Smilodon. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Tooth and Skin Colour Interrelationship across the Different Ethnic Groups.

Science.gov (United States)

Haralur, Satheesh B; Dibas, Ahmed Mohammed; Almelhi, Nabil Abdullah; Al-Qahtani, Dhafer Ali

2014-01-01

Objectives. The purpose of the study was to investigate the relation between skin and tooth colour parameters in various ethnic groups. Materials and Methods. Saudi Arabian, Indian, African, and East Asian ethnic groups of 75 each were included in the study. The tooth colour was determined by spectrophotometer in CIELAB parameters. The skin colour was measured at earlobe, forehead, and malar locations by clinical skin photography. The data was statistically analysed by one-way ANOVA and correlation tests. Results. The "L" vale for the Saudi Arabian group had a strong correlation at earlobe location (r = 0.275), while correlation was found at forehead (r = 0.271) and malar region (r = 0.261) with Indian ethnic group. A strong negative correlation was observed in African ethnic group at all three locations for "L" parameter. The redness value "a" is found to have strong negative linear correlation between the earlobe and tooth for Saudi Arabian (r = -0.240) and Indian ethnic groups (r = -0.268). The "b" showed no correlation with skin location in all groups except positive correlation in African ethnic groups. Conclusions. The strong correlation was found between the skin and tooth colour parameters; hence the skin colour can be used as a guide for artificial tooth selection in edentulous patients.

Dosimetric response evaluation of tooth enamel for accelerator-based neutron radiation

International Nuclear Information System (INIS)

Khan, R.F.H.; Rink, W.J.; Boreham, D.R.

2003-01-01

To study the neutron response of human tooth enamel, a number of experiments with an accelerator-based neutron source have been designed. The neutron beam was produced with the low gamma yield, 7 Li(p,n) 7 Be type thick target, using the 3 MV McMaster K.N. Van de Graaff accelerator. The dosimetry was done using a pre-calibrated snoopy type neutron dosimeter. Neutron irradiation induces a dosimetric signal in the tooth enamel at the same defect site as gamma produced damage with the same g-values (g parallel =1.9973, width 0.4 mT g perpendicular =2.002, width 0.3 mT). The dosimetric signal grows linearly with neutron dose from 6-35 Gy tissue dose. Dosimetric response in two different grain sizes (300-500 μm, and grains <4 mm) has shown increased dosimetric amplitude in the larger grains. Dose build up effect on tooth inside the mouth due to cheek was simulated by placing a 4 mm thick paraffin wax layer between the beam and tooth, but had little effect. These results show that for mean neutron energy of 280 keV, the relative neutron response of the human tooth enamel ranges from 8% to 12% of the equivalent gamma ray response

Methodic of the gamma-rays absorbed dose measurements on tooth enamel

International Nuclear Information System (INIS)

Linev, S.V.; Muravskij, V.A.; Mashevskij, A.A.; Ugolev, I.I.

1997-01-01

The analysis of the metrological aspects of the tooth enamel ESR dosimetry has been done. The sample preparation and measurement methods have been elaborated. The methods have passed metrological certification. The methods include tabletting of the mixture of tooth enamel powder and MnO paramagnetic centres concentration additional standard, two loops of additional irradiation of samples by 1 Gy dose and ESR-spectra measurements, calculation of absorbed dose by maximum likelihood algorithm. The algorithm of dose calculation uses enamel spectrum model with axial anisotropic spin-Hamiltonian based on 126 spectra of enamel samples. The algorithm takes into account spectra of the empty cavity, the tube for a sample, the glue and MnO standard. Certificated ESR-station is based on the ESR-analyser PS-100X. ESR-station provides tooth enamel absorbed dose measurements from 0.05 to 0.25 Gy with error 35%, and from 0.25 to 3 Gy with error 20%. The set of tooth enamel absorbed dose standard samples has been created and certificated for the purposes of ESR-station testing and certification. The set consists of 12 tabletted samples of tooth enamel irradiated by doses from 0.05 to 4 Gy. (authors). 7 refs., 1 tab., 2 figs

Retrospective dosimetry assessment using the 380 deg. C thermoluminescence peak of tooth enamel

Energy Technology Data Exchange (ETDEWEB)

Secu, C.E. [National Institute for Materials Physics, PO Box MG-7, 77125 Bucharest-Magurele (Romania); Cherestes, M. [Dozimed Ltd., Dosimetry Laboratory, 77125 Bucharest-Magurele (Romania); Secu, M., E-mail: msecu@infim.ro [National Institute for Materials Physics, PO Box MG-7, 77125 Bucharest-Magurele (Romania); Cherestes, C.; Paraschiva, V. [Dozimed Ltd., Dosimetry Laboratory, 77125 Bucharest-Magurele (Romania); Barca, C. [Faculty of Physics, University of Bucharest, 77125 Bucharest-Magurele (Romania)

2011-10-15

The thermoluminescence (TL) response to gamma-ray irradiation of tooth enamel is reported. The tooth enamel was separated from dentine by using mechanical and physico-chemical procedures followed by grinding (grain size {approx}100 {mu}m) and etching. The TL was attributed to the recombination of CO{sub 2}{sup -} radicals incorporated into or attached to the surface of hydroxyapatite crystals. The growth of the {approx}380 deg. C TL peak with absorbed dose was examined with irradiated tooth enamel samples and reconstructed doses evaluated for tooth enamel samples from four human subjects. - Highlights: > Thermoluminescence response after gamma-ray irradiation of tooth enamel was investigated. > Thermoluminescence was attributed to the recombination of CO{sub 2}{sup -} radicals. > CO{sub 2}{sup -} radicals are produced inside or at the surface of hydroxyapatite crystals. > From the growth of the 380C peak reconstructed doses have been evaluated.

Enamel alteration following tooth bleaching and remineralization.

Science.gov (United States)

Coceska, Emilija; Gjorgievska, Elizabeta; Coleman, Nichola J; Gabric, Dragana; Slipper, Ian J; Stevanovic, Marija; Nicholson, John W

2016-06-01

The purpose of this study was to compare the effects of professional tooth whitening agents containing highly concentrated hydrogen peroxide (with and without laser activation), on the enamel surface; and the potential of four different toothpastes to remineralize any alterations. The study was performed on 50 human molars, divided in two groups: treated with Opalescence(®) Boost and Mirawhite(®) Laser Bleaching. Furthermore, each group was divided into five subgroups, a control one and 4 subgroups remineralized with: Mirasensitive(®) hap+, Mirawhite(®) Gelleѐ, GC Tooth Mousse™ and Mirafluor(®) C. The samples were analysed by SEM/3D-SEM-micrographs, SEM/EDX-qualitative analysis and SEM/EDX-semiquantitative analysis. The microphotographs show that both types of bleaching cause alterations: emphasized perikymata, erosions, loss of interprizmatic substance; the laser treatment is more aggressive and loss of integrity of the enamel is determined by shearing off the enamel rods. In all samples undergoing remineralization deposits were observed, those of toothpastes based on calcium phosphate technologies seem to merge with each other and cover almost the entire surface of the enamel. Loss of integrity and minerals were detected only in the line-scans of the sample remineralized with GC Tooth Mousse™. The semiquantitative EDX analysis of individual elements in the surface layer of the enamel indicates that during tooth-bleaching with HP statistically significant loss of Na and Mg occurs, whereas the bleaching in combination with a laser leads to statistically significant loss of Ca and P. The results undoubtedly confirm that teeth whitening procedures lead to enamel alterations. In this context, it must be noted that laser bleaching is more aggressive for dental substances. However, these changes are reversible and can be repaired by application of remineralization toothpastes. © 2015 The Authors Journal of Microscopy © 2015 Royal Microscopical Society.

Abutment tooth loss in patients with overdentures.

Science.gov (United States)

Ettinger, Ronald L; Qian, Fang

2004-06-01

Since the 1960s, the use of natural teeth as overdenture abutments has become part of accepted clinical practice. Several longitudinal studies have been conducted, but tooth loss has not been reported to be a significant problem. The aim of this study was to identify the incidence and causes of tooth loss in a prospective cohort study of subjects wearing overdentures. The study, conducted between 1973 and 1994, evaluated 273 subjects (62.3 percent male) with a mean age of 59.6 years. Of the 273 subjects with 666 abutments, 74 lost 133 abutments. The most common cause of tooth loss was periodontal disease (29.3 percent) followed by periapical lesions (18.8 percent) and caries (16.5 percent). Through logistic regression, the authors found that subjects who lost teeth were more likely to have medical problems that could cause soft-tissue lesions of the oral mucosa, were less likely to use fluoride daily and were less likely to return for yearly recall visits. The authors found 22 vertical fractures in 17 subjects. Chi2 analysis revealed that overdenture teeth in the maxillary arch that were opposed by natural teeth were more likely to experience vertical fractures. In a study that followed up some patients for as long as 22 years, the rate of tooth loss was 20.0 percent. Many of these failures could have been prevented if patients had practiced better oral hygiene. The findings suggest that if a dentist recommends overdenture therapy, the patient needs to be examined regularly to reduce the risk of experiencing caries and periodontal disease. Also, if the abutments are in the maxilla and are opposed by natural teeth, the dentist should consider using thimble crowns to reduce the risk of vertical fractures.

Tooth extraction by orthodontic force after radiation therapy: report of case

Energy Technology Data Exchange (ETDEWEB)

Rodu, B.; Filler, S.J.; Woodfin, G.K.

1985-12-01

This report presents a therapeutic approach to orthodontic tooth extraction in a patient at high risk for the development of osteoradionecrosis with conventional techniques. The rationale for this procedure is discussed in detail, combining principles of radiation biology, clinical radiation therapy, and biomechanics of tooth movement.

Tooth extraction by orthodontic force after radiation therapy: report of case

International Nuclear Information System (INIS)

Rodu, B.; Filler, S.J.; Woodfin, G.K.

1985-01-01

This report presents a therapeutic approach to orthodontic tooth extraction in a patient at high risk for the development of osteoradionecrosis with conventional techniques. The rationale for this procedure is discussed in detail, combining principles of radiation biology, clinical radiation therapy, and biomechanics of tooth movement

Severe tooth wear in Prader-Willi syndrome. A case-control study.

Science.gov (United States)

Saeves, Ronnaug; Espelid, Ivar; Storhaug, Kari; Sandvik, Leiv; Nordgarden, Hilde

2012-05-28

Prader-Willi syndrome (PWS) is a rare complex multsystemic genetic disorder characterized by severe neonatal hypotonia, endocrine disturbances, hyperphagia and obesity, mild mental retardation, learning disabilities, facial dysmorphology and oral abnormalities. The purpose of the present study was to explore the prevalence of tooth wear and possible risk factors in individuals with Prader-Willi syndrome. Forty-nine individuals (6-40 years) with PWS and an age- and sex-matched control group were included. Tooth wear was evaluated from dental casts and intraoral photographs and rated by four examiners using the Visual Erosion Dental Examination (VEDE) scoring system and the individual tooth wear index IA. In accordance with the VEDE scoring system, tooth wear was also evaluated clinically. Whole saliva was collected. Mean VEDE score was 1.70 ± 1.44 in the PWS group and 0.46 ± 0.36 in the control group (p Prader-Willi syndrome. There is therefore considerable need for prosthodontic rehabilitation in young adults with PWS.

The Absolute Deviation Rank Diagnostic Approach to Gear Tooth Composite Fault

Directory of Open Access Journals (Sweden)

Guangbin Wang

2017-01-01

Full Text Available Aiming at nonlinear and nonstationary characteristics of the different degree with single fault gear tooth broken, pitting, and composite fault gear tooth broken-pitting, a method for the diagnosis of absolute deviation of gear faults is presented. The method uses ADAMS, respectively, set-up dynamics model of single fault gear tooth broken, pitting, and composite fault gear tooth broken-pitting, to obtain the result of different degree of broken teeth, pitting the single fault and compound faults in the meshing frequency, and the amplitude frequency doubling through simulating analysis. Through the comparison with the normal state to obtain the sensitive characteristic of the fault, the absolute value deviation diagnostic approach is used to identify the fault and validate it through experiments. The results show that absolute deviation rank diagnostic approach can realize the recognition of gear single faults and compound faults with different degrees and provide quick reference to determine the degree of gear fault.

Expression of Sox genes in tooth development.

Science.gov (United States)

Kawasaki, Katsushige; Kawasaki, Maiko; Watanabe, Momoko; Idrus, Erik; Nagai, Takahiro; Oommen, Shelly; Maeda, Takeyasu; Hagiwara, Nobuko; Que, Jianwen; Sharpe, Paul T; Ohazama, Atsushi

2015-01-01

Members of the Sox gene family play roles in many biological processes including organogenesis. We carried out comparative in situ hybridization analysis of seventeen sox genes (Sox1-14, 17, 18, 21) during murine odontogenesis from the epithelial thickening to the cytodifferentiation stages. Localized expression of five Sox genes (Sox6, 9, 13, 14 and 21) was observed in tooth bud epithelium. Sox13 showed restricted expression in the primary enamel knots. At the early bell stage, three Sox genes (Sox8, 11, 17 and 21) were expressed in pre-ameloblasts, whereas two others (Sox5 and 18) showed expression in odontoblasts. Sox genes thus showed a dynamic spatio-temporal expression during tooth development.

Tooth erosion awareness in a Brazilian dental school.

Science.gov (United States)

Hermont, Ana Paula; Oliveira, Patricia A D; Auad, Sheyla M

2011-12-01

The aim of this cross-sectional study was to assess awareness and attitudes related to tooth erosion among dental students, patients, and faculty members in a Brazilian dental school. Data were collected by means of a self-applied questionnaire that was distributed among 298 participants. The response rate was 89.6 percent. Chi-square and Fisher's exact tests were used for statistical analysis (perosion (72.9 percent), with lower percentages among the patients (perosion (p=0.004). Almost 30 percent of the students did not know if they had had a patient with erosion, and 73.1 percent reported they were not advised by their clinical supervisor to examine their patients for tooth erosion (p=0.138). Concerning the faculty, 23.6 percent of them along with 61.5 percent of the students did not feel prepared to diagnose the condition (perosion (89.6 percent). Knowledge about tooth erosion was not as widely evident as it should be in this sample, suggesting the need for better understanding and communication in this important area of oral health care.

Cigarette smoking and tooth loss experience among young adults: a national record linkage study

Directory of Open Access Journals (Sweden)

Tanaka Keiko

2007-11-01

Full Text Available Abstract Background Various factors affect tooth loss in older age including cigarette smoking; however, evidence regarding the association between smoking and tooth loss during young adulthood is limited. The present study examined the association between cigarette smoking and tooth loss experience among adults aged 20–39 years using linked data from two national databases in Japan. Methods Two databases of the National Nutrition Survey (NNS and the Survey of Dental Diseases (SDD, which were conducted in 1999, were obtained from the Ministry of Health, Labor and Welfare with permission for analytical use. In the NNS, participants received physical examinations and were interviewed regarding dietary intake and health practices including cigarette smoking, whereas in the SDD, participants were asked about their frequency of daily brushing, and received oral examinations by certified dentists. Among 6,805 records electronically linked via household identification code, 1314 records of individuals aged 20 to 39 years were analyzed. The prevalence of 1+ tooth loss was compared among non-, former, and current smokers. Multiple logistic regression models were constructed including confounders: frequency of tooth brushing, body mass index, alcohol consumption, and intake of vitamins C and E. Results Smoking rates differed greatly in men (53.3% and women (15.5%. The overall prevalence of tooth loss was 31.4% (31.8% men and 31.1% women. Tooth loss occurred more frequently among current smokers (40.6% than former (23.1% and non-smokers (27.9%. Current smoking showed a significant association with 1+ tooth loss in men (adjusted OR = 2.21 [1.40–3.50], P = 0.0007 and women (1.70 [1.13–2.55], P = 0.0111. A significant positive exposure-related relationship between cigarette smoking status and tooth loss was observed (P for trend Conclusion An association between cigarette smoking and tooth loss was evident among young adults throughout Japan. Due to

Ability of mini-implant-facilitated micro-osteoperforations to accelerate tooth movement in rats.

Science.gov (United States)

Cheung, Tracy; Park, Juyoung; Lee, Deborah; Kim, Catherine; Olson, Jeffrey; Javadi, Shadi; Lawson, Gregory; McCabe, James; Moon, Won; Ting, Kang; Hong, Christine

2016-12-01

Although current techniques for accelerated tooth movement often involve invasive surgical procedures, micro-osteoperforations (MOPs) using mini-implants may facilitate orthodontic tooth movement without raising flaps, reduce surgical risks, and increase patient acceptance. In this study, we evaluated the effectiveness of mini-implant-facilitated MOPs in inducing accelerated tooth movement and investigated the potential risks for root resorption. Five MOPs were placed on the left side around the maxillary first molars in 6 rats using an automated mini-implant driver, whereas the right side received no MOPs as the control. Closed-coiled springs were secured from incisors to first molars for orthodontic tooth movement. Tooth movement was measured, and samples underwent radiologic and histologic analyses. The MOP side exhibited a 1.86-fold increase in the rate of tooth movement with decreased bone density and bone volume around the first molars compared with the control side. Hematoxylin and eosin and tartrate-resistant acid phosphatase analyses showed increased numbers of osteoclasts as well as new bone formation. Three-dimensional volumetric analysis of all 5 roots of the maxillary first molars demonstrated no statistically significant difference in root volumes. Mini-implant-facilitated MOPs accelerated tooth movement without increased risk for root resorption and therefore may become a readily available and efficient treatment option to shorten orthodontic treatment time with improved patient acceptance. Copyright © 2016 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

The Permian reptile Opisthodontosaurus carrolli: a model for acrodont tooth replacement and dental ontogeny.

Science.gov (United States)

Haridy, Yara; LeBlanc, Aaron R H; Reisz, Robert R

2018-03-01

Continuous tooth replacement is common for tetrapods, but some groups of acrodont lepidosaurs have lost the ability to replace their dentition (monophyodonty). Acrodonty, where the tooth attaches to the apex of the jawbone, is an unusual form of tooth attachment that has been associated with the highly autapomorphic condition of monophyodonty. Beyond Lepidosauria, very little is known about the relationship between acrodonty and monophyodonty in other amniotes. We test for this association with a detailed study of the dentition of Opisthodontosaurus, an unusual Early Permian captorhinid eureptile with acrodont dentition. We provide clear evidence, both histological and morphological, that there were regular tooth replacement events in the lower jaw of Opisthodontosaurus, similar to its captorhinid relatives. Thus, our study of the oldest known amniote with an acrodont dentition shows that acrodonty does not inhibit tooth replacement, and that many of the characteristics assigned to lepidosaurian acrodonty are actually highly derived features of lepidosaurs that have resulted secondarily from a lack of tooth replacement. In the context of reptilian dental evolution, we propose the retention of the simple definition of acrodonty, which only pertains to the relative position of the tooth at the apex of the jaw, where the jaw possesses equal lingual and labial walls. This definition of implantation therefore focuses solely on the spatial relationship between the tooth and the jawbone, and separates this relationship from tooth development and replacement. © 2017 Anatomical Society.

Large scale study of tooth enamel

International Nuclear Information System (INIS)

Bodart, F.; Deconninck, G.; Martin, M.T.

Human tooth enamel contains traces of foreign elements. The presence of these elements is related to the history and the environment of the human body and can be considered as the signature of perturbations which occur during the growth of a tooth. A map of the distribution of these traces on a large scale sample of the population will constitute a reference for further investigations of environmental effects. On hundred eighty samples of teeth were first analyzed using PIXE, backscattering and nuclear reaction techniques. The results were analyzed using statistical methods. Correlations between O, F, Na, P, Ca, Mn, Fe, Cu, Zn, Pb and Sr were observed and cluster analysis was in progress. The techniques described in the present work have been developed in order to establish a method for the exploration of very large samples of the Belgian population. (author)

Assessment of the amount of tooth wear on dental casts and intra-oral photographs

NARCIS (Netherlands)

Wetselaar, P.; Wetselaar-Glas, M.J.M.; Koutris, M.; Visscher, C.M.; Lobbezoo, F.

2016-01-01

Tooth wear is a multifactorial condition, leading to the loss of dental hard tissues. Many grading scales are available to assess the amount of tooth wear, one of which is the tooth wear evaluation system (TWES). A grading scale can be used chairside, on casts and on photographs. The aim was to test

Tooth Wear Inclination in Great Ape Molars.

Science.gov (United States)

Knight-Sadler, Jordan; Fiorenza, Luca

2017-01-01

Primate dietary diversity is reflected in their dental morphology, with differences in size and shape of teeth. In particular, the tooth wear angle can provide insight into a species' ability to break down certain foods. To examine dietary and masticatory information, digitized polygon models of dental casts provide a basis for quantitative analysis of wear associated with tooth attrition. In this study, we analyze and compare the wear patterns of Pongo pygmaeus, Gorilla gorillagorilla and Pan troglodytes schweinfurthii lower molars, focusing on the degree of inclination of specific wear facets. The variation in wear angles appears to be indicative of jaw movements and the specific stresses imposed on food during mastication, reflecting thus the ecology of these species. Orangutans exhibit flatter wear angles, more typical of a diet consisting of hard and brittle foods, while gorillas show a wear pattern with a high degree of inclination, reflecting thus their more leafy diet. Chimpanzees, on the other hand, show intermediate inclinations, a pattern that could be related to their highly variable diet. This method is demonstrated to be a powerful tool for better understanding the relationship between food, mastication and tooth wear processes in living primates, and can be potentially used to reconstruct the diet of fossil species. © 2017 S. Karger AG, Basel.

Role of multiple cusps in tooth fracture.

Science.gov (United States)

Barani, Amir; Bush, Mark B; Lawn, Brian R

2014-07-01

The role of multiple cusps in the biomechanics of human molar tooth fracture is analysed. A model with four cusps at the bite surface replaces the single dome structure used in previous simulations. Extended finite element modelling, with provision to embed longitudinal cracks into the enamel walls, enables full analysis of crack propagation from initial extension to final failure. The cracks propagate longitudinally around the enamel side walls from starter cracks placed either at the top surface (radial cracks) or from the tooth base (margin cracks). A feature of the crack evolution is its stability, meaning that extension occurs steadily with increasing applied force. Predictions from the model are validated by comparison with experimental data from earlier publications, in which crack development was followed in situ during occlusal loading of extracted human molars. The results show substantial increase in critical forces to produce longitudinal fractures with number of cuspal contacts, indicating a capacity for an individual tooth to spread the load during mastication. It is argued that explicit critical force equations derived in previous studies remain valid, at the least as a means for comparing the capacity for teeth of different dimensions to sustain high bite forces. Copyright © 2014 Elsevier Ltd. All rights reserved.

The 3rd international intercomparison on EPR tooth dosimetry: Part 1, general analysis

International Nuclear Information System (INIS)

Wieser, A.; Debuyst, R.; Fattibene, P.

2005-01-01

The objective of the 3rd International Intercomparison on Electron Paramagnetic Resonance (EPR) Tooth Dosimetry was the evaluation of laboratories performing tooth enamel dosimetry below 300 mGy. Participants had to reconstruct the absorbed dose in tooth enamel from 11 molars, which were cut into two halves. One half of each tooth was irradiated in a 60 Co beam to doses in the ranges of 30-100 mGy (5 samples), 100-300 mGy (5 samples), and 300-900 mGy (1 sample). Fourteen international laboratories participated in this intercomparison programme. A first analysis of the results and an overview of the essential features of methods applied in different laboratories are presented. The relative standard deviation of results of all methods was better than 27% for applied doses in the range of 79-704 mGy. In the analysis of the unirradiated tooth halves 8% of the samples were identified as outliers with additional absorbed dose above background dose

Permanent tooth loss and sugar-sweetened beverage intake in U.S. young adults.

Science.gov (United States)

Kim, Sunkyung; Park, Sohyun; Lin, Mei

2017-03-01

In young adults, sugar-sweetened beverage (SSB) intake is associated with dental caries, which in turn is a major contributor to tooth loss. The independent role of SSB intake on tooth loss, however, has not been well-described. This cross-sectional study examined associations between tooth loss and SSB intake among U.S. young adults. The outcome was number of permanent teeth lost because of dental caries or periodontal disease (0, 1-5, ≥6 teeth). Data from the 2012 Behavioral Risk Factor Surveillance System were used. The 22,526 adults aged 18-39 years completed the Sugar Drink Module. The exposure variable was daily frequency of SSB intake. We used multinomial logistic regression to examine the adjusted associations between tooth loss and daily SSB consumption (0, >0 to 2 times/day). Approximately, 26% of young adults reported losing at least one permanent tooth. Tooth loss was positively associated with SSB intake frequency; the odds of losing 1-5 teeth were higher among adults drinking SSBs >0-2 times/day (OR = 1.97, 95%CI = 1.51-2.58) than non-SSB consumers. The odds of losing ≥6 teeth were higher among adults drinking SSBs 1-2 times/day (OR = 2.20, 95%CI = 1.15-4.22) and >2 times/day (OR = 2.81, 95%CI = 1.37-5.76) than non-SSB consumers. Frequency of SSB consumption was positively associated with tooth loss among young adults even when the average SSB intake was less than one time per day. This study suggests that efforts to reduce SSB intake among young adults may help to decrease the risk of tooth loss. © 2016 American Association of Public Health Dentistry.

Rolling-Tooth Core Breakoff and Retention Mechanism

Science.gov (United States)

Badescu, Mircea; Bickler, Donald B.; Sherrit, Stewart; Bar-Cohen, Yoseph; Bao, Xiaoqi; Hudson, Nicolas H.

2011-01-01

Sampling cores requires the controlled breakoff of the core at a known location with respect to the drill end. An additional problem is designing a mechanism that can be implemented at a small scale that is robust and versatile enough to be used for a variety of core samples. This design consists of a set of tubes (a drill tube and an inner tube) and a rolling element (rolling tooth). An additional tube can be used as a sample tube. The drill tube and the inner tube have longitudinal holes with the axes offset from the axis of each tube. The two eccentricities are equal. The inner tube fits inside the drill tube, and the sample tube fits inside the inner tube. While drilling, the two tubes are positioned relative to each other such that the sample tube is aligned with the drill tube axis and core. The drill tube includes teeth and flutes for cuttings removal. The inner tube includes, at the base, the rolling element implemented as a wheel on a shaft in an eccentric slot. An additional slot in the inner tube and a pin in the drill tube limit the relative motion of the two tubes. While drilling, the drill assembly rotates relative to the core and forces the rolling tooth to stay hidden in the slot along the inner tube wall. When the drilling depth has been reached, the drill bit assembly is rotated in the opposite direction, and the rolling tooth is engaged and penetrates into the core. Depending on the strength of the created core, the rolling tooth can score, lock the inner tube relative to the core, start the eccentric motion of the inner tube, and break the core. The tooth and the relative position of the two tubes can act as a core catcher or core-retention mechanism as well. The design was made to fit the core and hole parameters produced by an existing bit; the parts were fabricated and a series of demonstration tests were performed. This invention is potentially applicable to sample return and in situ missions to planets such as Mars and Venus, to moons such

Nuclear-chemical methods in a hard tooth tissue abrasion study

International Nuclear Information System (INIS)

Gosman, A.; Spevacek, V.; Konicek, J.; Vopalka, D.; Housova, D.; Dolezalova, L.

1999-01-01

The advanced method consists in implantation-labelling of the thin surface layers of the solid objects, e.g. hard tooth tissue, by atoms of suitable natural or artificial radionuclides. Nuclides from the uranium series were implanted into the surface by using nuclear recoil effect at alpha decay of 226 Ra to 222 Rn, alpha decay of 222 Rn to RaA, alpha decay of RaA to RaB (beta-emitter) and further alpha or beta emitters. With regard to chosen alpha detection and to the half-lives of the radionuclides, there was actually measured the activity of 222 Rn, RaA and RaC' in the thin surface layer. This was followed by the laboratory simulation of the abrasion in the system of 'toothbrush - various suspensions of the tooth-pastes - hard tooth tissue (or material standard - ivory)' in specially designed device - the dentoabrasion meter. The activities of the tissue surface measured before and after abrasion were used for calculations of the relative drop of the surface activity. On this basis the influence of various tooth-pastes containing various abrasive substances was determined. (author)

Tooth labeling in cone-beam CT using deep convolutional neural network for forensic identification

Science.gov (United States)

Miki, Yuma; Muramatsu, Chisako; Hayashi, Tatsuro; Zhou, Xiangrong; Hara, Takeshi; Katsumata, Akitoshi; Fujita, Hiroshi

2017-03-01

In large disasters, dental record plays an important role in forensic identification. However, filing dental charts for corpses is not an easy task for general dentists. Moreover, it is laborious and time-consuming work in cases of large scale disasters. We have been investigating a tooth labeling method on dental cone-beam CT images for the purpose of automatic filing of dental charts. In our method, individual tooth in CT images are detected and classified into seven tooth types using deep convolutional neural network. We employed the fully convolutional network using AlexNet architecture for detecting each tooth and applied our previous method using regular AlexNet for classifying the detected teeth into 7 tooth types. From 52 CT volumes obtained by two imaging systems, five images each were randomly selected as test data, and the remaining 42 cases were used as training data. The result showed the tooth detection accuracy of 77.4% with the average false detection of 5.8 per image. The result indicates the potential utility of the proposed method for automatic recording of dental information.

Resection of the Tooth Apex with Diode Laser

Directory of Open Access Journals (Sweden)

Uzunov Tz.

2014-06-01

Full Text Available An “in vitro” experimental study has been carried out on 70 extracted teeth. A laser resection of the root apex has been carried out with diode laser beam with a wavelength of - 810 ± 10 nm. Sequentially a radiation with increasing power has been applied, as follows: 1,3 W, 2W, 3W, 4W, 5W, 6W, 7W, in electro surgery mode. Successful resection of the tooth apex has been performed at: 3W; 4W; 5W; 6W and 7W power. It was established that when laser resected the tooth apex carbonizes.

Simple direct composite resin restoration on endodontically treated tooth: A case report

Directory of Open Access Journals (Sweden)

Wahyuni Suci Dwiandhany

2016-06-01

Full Text Available Endodontically treated teeth generally havegreat structure loss so that the resistance to fracture is reduced. Therefore, the post-endodontic restoration design that covers the entire cusp (full cuspal coverage is necessary to increase the resistance of teeth to fracture. The aim of this case report is to present direct onlay restoration technique using composite resin material in non-vital tooth with chronic apical periodontitis. A 74-years-old male patient came to the clinic complaining of discomfort in the lower right posterior tooth related to eating since 1 week ago. Clinical examination revealed a large amalgam restoration on the second lower right molar, the tooth is negative to pulp sensitivity test, and tender to percussion. Radiographically, the tooth showed periapical radiolucency at distal and mesial root. The diagnosis of the tooth was chronic apical periodontitis. The treatment plan is a non-vital root canal treatment with multiple visit. Root canal preparation with rotary files (ProTaper Next, Dentsply, Germany was performed on the first visit and irrigated with NaOCl. On the next visit, during subjective examination, there was no pain complaints and the percussion test was negative so the obturation with a single cone technique can be done. On the final visit, direct onlay restoration using nano-hybrid composite resin material (Polofil NHT, Voco, Germany was performed. In conclusion, after 3 months follow up, the marginal integrity of the restoration remains intact and the tooth were functioned properly.

Reactive correction of a maxillary incisor in single-tooth crossbite following periodontal therapy.

Science.gov (United States)

Huang, Chih-Hao; Brunsvold, Michael A

2005-05-01

The reactive correction of a single tooth anterior crossbite following periodontal therapy is described. This case report provides new information regarding correction of a crossbite relationship and con- firms existing reports of tooth movement following periodontal therapy. A 39-year-old woman in good general health presented with a history of recurrent periodontal abscesses of a maxillary incisor. Probing depths of the abscessed tooth ranged from 5 to 12 mm, and class 1 mobility was noted. Radiographs revealed that the tooth had previously been treated endodontically. The patient's periodontal diagnosis was generalized chronic moderate to severe periodontitis. Treatment considerations were complicated by a single-tooth crossbite relationship of the involved incisor and clinical evidence that the periodontal abscess communicated with an apical infection. Treatment of the abscess consisted of cause-related therapy, bone grafting, and occlusal adjustment. Five months after surgical treatment, an edge-to-edge incisal relationship was observed, the first indicator of tooth movement. Further correction to a normal incisal relationship resulted 1 year after modification of the proximal contact. At this time, there was normal probing depth with only slight recession and mobility. Bone fill was radiographically noted. It appears that some cases of maxillary incisor crossbite that are complicated by periodontal disease may be corrected, without orthodontic appliances, following periodontal treatment.

Characterization of glycosaminoglycans during tooth development and mineralization in the axolotl, Ambystoma mexicanum.

Science.gov (United States)

Wistuba, J; Völker, W; Ehmcke, J; Clemen, G

2003-10-01

Glycosaminoglycans (GAGs) involved in the formation of the teeth of Ambystoma mexicanum were located and characterized with the cuprolinic blue (CB) staining method and transmission electron microscopy (TEM). Glycosaminoglycan-cuprolinic blue precipitates (GAGCB) were found in different compartments of the mineralizing tissue. Various populations of elongated GAGCB could be discriminated both according to their size and their preferential distribution in the extracellular matrix (ECM). GAGCB populations that differ in their composition could be attributed not only to the compartments of the ECM but also to different zones and to different tooth types (early-larval and transformed). Larger precipitates were only observed within the dentine matrix of the shaft of the early-larval tooth. The composition of the populations differed significantly between the regions of the transformed tooth: pedicel, shaft and dividing zone. In later stages of tooth formation, small-sized GAGCBs were seen as intracellular deposits in the ameloblasts. It is concluded that the composition of GAGCB populations seems to play a role in the mineralization processes during tooth development in A. mexicanum and influence qualitative characteristics of the mineral in different tooth types and zones, and it is suggested that GAGs might be resorbed by the enamel epithelium during the late phase of enamel formation.

Effect of Dietary Vitamin C on Orthodontic Tooth Movement in Rats

Directory of Open Access Journals (Sweden)

Amirfarhang Miresmaeili

2015-11-01

Full Text Available Objectives: Bone remodeling occurs during orthodontic treatment; this process enables tooth movement. Many factors can affect bone remodeling at the cellular level, such as nutritional supplements that can affect tooth movement. The present study was designed to evaluate the effect of dietary vitamin C on orthodontic tooth movement in rats. Materials and Methods: This study was carried out on 36 six-week male Wistar rats with a mean weight of 225+32 g, which were randomly allocated to two equal groups. Rats in the case group received 1wt% vitamin C in their daily water. Opening springs were placed on the incisor teeth of both case and control groups. After 17 days, rats were sacrificed; the distance between the mesio-incisal angles of these teeth was measured with a digital caliper. Histological sections were made containing incisor teeth and alveolar bone and stained by hematoxylin-eosin. The number of resorption lacunae was evaluated using light microscopy.Results: Our findings showed that the amount of tooth movement in the vitamin C group was significantly higher than that in the control group (P<0.001. The osteoclast counts were significantly higher in vitamin C group (P=0.036.Conclusion: Oral vitamin C can increase orthodontic tooth movement in rats with more osteoclast lacunae around root in the pressure area. 

Effect of Cervical Lessions on the Tooth FEM Study

OpenAIRE

Gabriela Bereşescu; Ligia Brezeanu; Claudia Şoaita

2010-01-01

The approach used until recently concerning the phenomena of dental abfraction points to the conclusion that the cervical area of the tooth, were this type of lesion usually occur, concentrates the stress resulted from the action of the forces applied on various areas on the crown. Moreover, any lesion in the cervical area facilitates the possibility of its advance into the tooth, ultimately fracturing it. Our paper presents a FEM (finite element method) study on the results of a mechanical a...

Dependencies of the radiation sensitivity of human tooth enamel in EPR dosimetry

International Nuclear Information System (INIS)

Wieser, A.; El-Faramawy, N.; Meckbach, R.

2001-01-01

The EPR dose response of tooth enamel was determined for human molars collected in Egypt. The influence of age, gender and residence of the tooth donors as well as tooth position and sample preparation on EPR sensitivity and its variability over the enamel samples was investigated. The EPR sensitivity and its variability were found to depend only on the sample preparation procedure. The variability in EPR sensitivity of enamel from Egyptian teeth was maximally 10% and the mean sensitivity was in good agreement with that of German teeth

A probability distribution model of tooth pits for evaluating time-varying mesh stiffness of pitting gears

Science.gov (United States)

Lei, Yaguo; Liu, Zongyao; Wang, Delong; Yang, Xiao; Liu, Huan; Lin, Jing

2018-06-01

Tooth damage often causes a reduction in gear mesh stiffness. Thus time-varying mesh stiffness (TVMS) can be treated as an indication of gear health conditions. This study is devoted to investigating the mesh stiffness variations of a pair of external spur gears with tooth pitting, and proposes a new model for describing tooth pitting based on probability distribution. In the model, considering the appearance and development process of tooth pitting, we model the pitting on the surface of spur gear teeth as a series of pits with a uniform distribution in the direction of tooth width and a normal distribution in the direction of tooth height, respectively. In addition, four pitting degrees, from no pitting to severe pitting, are modeled. Finally, influences of tooth pitting on TVMS are analyzed in details and the proposed model is validated by comparing with a finite element model. The comparison results show that the proposed model is effective for the TVMS evaluations of pitting gears.

The timing of tooth eruption and root development of permanent canine and premolars in Korean children

Energy Technology Data Exchange (ETDEWEB)

Cheong, Chang Shin; Jung, Yun Hoa; Cho, Bong Hae [Department of Oral and Maxillofacial Radiology, School of Dentistry, Pusan National University, Pusan (Korea, Republic of)

2010-09-15

The aim of this study was to investigate the timing and sequence of eruption of permanent canine and premolars, and to evaluate tooth calcification stage on emergence in Korean children. The sample was comprised of 1,266 children (male 720, female 546) aged from 7-13 years. Tooth eruption and calcification stages were determined through oral and panoramic radiographic examination, respectively. Probit analysis was used to calculate the timing of tooth eruption and tooth calcification stage from these cross-sectional data. In both males and females, eruption occurred around the time when one third of tooth root or more was formed. The sequence was as follows: first premolar, canine, and second premolar in maxilla, and canine, first premolar and second premolar in mandible. Tooth eruption occurred earlier in girls compared with boys, averaging 0.63 years. Eruption sequence is identical in males and females with a trend for females to erupt earlier than males. Tooth eruption becomes earlier over the past decades in Korean children.

The timing of tooth eruption and root development of permanent canine and premolars in Korean children

International Nuclear Information System (INIS)

Cheong, Chang Shin; Jung, Yun Hoa; Cho, Bong Hae

2010-01-01

The aim of this study was to investigate the timing and sequence of eruption of permanent canine and premolars, and to evaluate tooth calcification stage on emergence in Korean children. The sample was comprised of 1,266 children (male 720, female 546) aged from 7-13 years. Tooth eruption and calcification stages were determined through oral and panoramic radiographic examination, respectively. Probit analysis was used to calculate the timing of tooth eruption and tooth calcification stage from these cross-sectional data. In both males and females, eruption occurred around the time when one third of tooth root or more was formed. The sequence was as follows: first premolar, canine, and second premolar in maxilla, and canine, first premolar and second premolar in mandible. Tooth eruption occurred earlier in girls compared with boys, averaging 0.63 years. Eruption sequence is identical in males and females with a trend for females to erupt earlier than males. Tooth eruption becomes earlier over the past decades in Korean children.

Computerized Analysis of Digital Photographs for Evaluation of Tooth Movement.

Science.gov (United States)

Toodehzaeim, Mohammad Hossein; Karandish, Maryam; Karandish, Mohammad Nabi

2015-03-01

Various methods have been introduced for evaluation of tooth movement in orthodontics. The challenge is to adopt the most accurate and most beneficial method for patients. This study was designed to introduce analysis of digital photographs with AutoCAD software as a method to evaluate tooth movement and assess the reliability of this method. Eighteen patients were evaluated in this study. Three intraoral digital images from the buccal view were captured from each patient in half an hour interval. All the photos were sent to AutoCAD software 2011, calibrated and the distance between canine and molar hooks were measured. The data was analyzed using intraclass correlation coefficient. Photographs were found to have high reliability coefficient (P > 0.05). The introduced method is an accurate, efficient and reliable method for evaluation of tooth movement.

Oral Health Problems And Causes Of Tooth Loss At The University ...

African Journals Online (AJOL)

Context Several oral diseases and conditions are associated with tooth loss. Objective: The aim of this study was to determine the prevalence of oral health problems seen at the University of Nigeria Teaching Hospital (UNTH) in one year with the view to highlighting causes of tooth loss in this environment. Methods This ...

Causes of Charcot-Marie-Tooth Disease (CMT)

Science.gov (United States)

... Marie-Tooth Disease (CMT) Congenital Muscular Dystrophy (CMD) Duchenne Muscular Dystrophy (DMD) Emery-Dreifuss Muscular Dystrophy Endocrine Myopathies Metabolic Diseases of Muscle Mitochondrial Myopathies (MM) Myotonic Dystrophy (DM) Spinal-Bulbar ...

New method of control of tooth whitening

Science.gov (United States)

Angelov, I.; Mantareva, V.; Gisbrecht, A.; Valkanov, S.; Uzunov, Tz.

2010-10-01

New methods of control of tooth bleaching stages through simultaneous measurements of a reflected light and a fluorescence signal are proposed. It is shown that the bleaching process leads to significant changes in the intensity of a scattered signal and also in the shape and intensity of the fluorescence spectra. Experimental data illustrate that the bleaching process causes essential changes in the teeth discoloration in short time as 8-10 min from the beginning of the application procedure. The continuation of the treatment is not necessary moreover the probability of the enamel destroy increases considerably. The proposed optical back control of tooth surface is a base for development of a practical set up to control the duration of the bleaching procedure.

Dental-derived Stem Cells and whole Tooth Regeneration: an Overview

OpenAIRE

Dannan, Aous

2009-01-01

The need for new dental tissue-replacement therapies is evident in recent reports which reveal startling statistics regarding the high incidence of tooth decay and tooth loss. Recent advances in the identification and characterization of dental stem cells, and in dental tissue-engineering strategies, suggest that bioengineering approaches may successfully be used to regenerate dental tissues and whole teeth. Interest in dental tissue-regeneration applications continues to increase as clinical...

[The effect of osteogenic inducer on healing of tooth extraction sockets].

Science.gov (United States)

Chen, Junliang; Shan, Chuncheng; He, Yun; Xia, Delin

2012-06-01

To study the effect of osteogenic inducer (dexamethasone, beta-sodium glycerophosphate and Vitamin C) carried by gelatin sponge on healing and remodeling of tooth extraction sockets. Fifty rabbits were selected. After extracting the first premolars of bilateral maxillary, the right side tooth extraction sockets were filled with gelatin sponge containing osteogenic inducer as experimental side, tooth extraction sockets on left side were filled with gelatin sponge as control. Every ten rabbits were executed at the end of 1, 2, 4, 8, 12 weeks after tooth extraction. Bone density was measured through digital X-ray images. The specimens were examined by histology. The absorption height of alveolar bone at 12 weeks was measured. X-ray measurement showed that the bone density of experimental side was higher than that of control side at 2, 4, 8, 12 weeks, the difference had statistical significance (Psockets of experimental side was earlier than that in control side. The absorptional height of alveolar bone had significant difference between experimental side and control side (Psockets can promote the healing and new bone formation and prevent from alveolar bone absorption.

Tooth bleaching using peroxide-containing agents: current status of safety issues.

Science.gov (United States)

Li, Y

1998-08-01

During the last 10 years, at-home tooth bleaching using peroxide-containing agents has quickly become well accepted. It is one of the most popular cosmetic dental procedures for whitening teeth. Although there are few disputes regarding their efficacy, concerns and debates have continued regarding the safety of peroxide-containing tooth bleaching agents. Potential carcinogenicity and genotoxicity of the peroxides used in bleaching agents are the two most persistent and controversial issues. This article reviews and discusses available information on carcinogenicity and genotoxicity of hydrogen peroxide and the potential risks associated with the use of peroxide-containing bleaching agents. Clinical studies reported after the 1996 international symposium on responses of oral tissues to peroxide-containing bleaching agents are also reviewed. Overall evidence supports the conclusion that the proper use of peroxide-containing at-home tooth bleaching agents is safe. However, potential adverse effects may occur in inappropriate applications, abuses, or the use of inappropriate products. At-home tooth bleaching should be monitored by dental professionals to maximize the benefits while minimizing potential risks.

Early detection of tooth wear by en-face optical coherence tomography

Science.gov (United States)

Mărcăuteanu, Corina; Negrutiu, Meda; Sinescu, Cosmin; Demjan, Eniko; Hughes, Mike; Bradu, Adrian; Dobre, George; Podoleanu, Adrian G.

2009-02-01

Excessive dental wear (pathological attrition and/or abfractions) is a frequent complication in bruxing patients. The parafunction causes heavy occlusal loads. The aim of this study is the early detection and monitoring of occlusal overload in bruxing patients. En-face optical coherence tomography was used for investigating and imaging of several extracted tooth, with a normal morphology, derived from patients with active bruxism and from subjects without parafunction. We found a characteristic pattern of enamel cracks in patients with first degree bruxism and with a normal tooth morphology. We conclude that the en-face optical coherence tomography is a promising non-invasive alternative technique for the early detection of occlusal overload, before it becomes clinically evident as tooth wear.

Trends in Social Inequality in Tooth Brushing among Adolescents: 1991-2014

DEFF Research Database (Denmark)

Holstein, Bjørn Evald; Bast, Lotus Sofie; Brixval, Carina Sjöberg

2015-01-01

This study examines whether social inequality in tooth brushing frequency among adolescents changed from 1991 to 2014. The data material was seven comparable cross-sectional studies of nationally representative samples of 11- to 15-year-olds in Denmark with data about frequency of tooth brushing...... and occupation of parents. The total number of participants was 31,464, of whom 21.7% brushed their teeth less than the recommended 2 times a day. The absolute social inequality measured as prevalence difference between low and high social class increased from 7.7% in 1991 to 14.6% in 2014. The relative social...... inequality assessed by odds ratios for infrequent tooth brushing also increased from 1991 to 2014....

The Role of Mechanical Force in Molecular and Cellular during Orthodontic Tooth Movement

Directory of Open Access Journals (Sweden)

Ida Bagus Narmada

2012-10-01

Full Text Available Application of mechanical force on abnormally positioned tooth, cause changes in tooth location and transmitted to the bone ia the periodontal ligament (PDL produce orthodontic tooth movement. This force application is further way that remodeling in the area occurs. In order to develop biological strategies for enhancing this movement of teeth in bone, the underlying mechanisms of bone resorption and apposition should be understood in detail. Analysis of gingival crevicular fluid (GCF may be a good means of examining the on going molecular and cellular process associated with gingival and bone turnover during orthodontic tooth movement. If it could be possible to biologically monitor and predict the outcome of orthodontic force, then the appliance management could be based on dividual tissue response and the effectiveness of the treatment could be improved and understanding their biology is critical to finding ways to modify bone biology to move teeth faster. The present article reviewed a short introduction to some mayors advanced mechanical force in molecular and cellular biology during orthodontic tooth movement.DOI: 10.14693/jdi.v15i3.30

Bleaching of the discolored traumatized tooth

DEFF Research Database (Denmark)

Dahl, Jon E.; Kopperud, Siemen E.; Pallesen, Ulla

2018-01-01

This chapter focuses on the treatment of discolored traumatized teeth, most of them being non-vital and subsequently, endodontically treated. Tooth bleaching based upon hydrogen peroxide as the active agent, applied directly or produced in a chemical reaction from sodium perborate or carbamide pe...

Age effect on orthodontic tooth movement

NARCIS (Netherlands)

Ren, Yijin

2003-01-01

This study was performed to investigate the effect of age on the efficiency of orthodontic tooth movement based on critical literature reviews, studies on a standardized orthodontic animal model and a non-invasive clinical investigation. A systematic review was performed on the optimum force for

Storing tooth segments for optimal esthetics

NARCIS (Netherlands)

Tuzuner, T.; Turgut, S.; Özen, B.; Kılınç, H.; Bagis, B.

2016-01-01

Objective: A fractured whole crown segment can be reattached to its remnant; crowns from extracted teeth may be used as pontics in splinting techniques. We aimed to evaluate the effect of different storage solutions on tooth segment optical properties after different durations. Study design: Sixty

MSX1 gene variant - its presence in tooth absence - a case control genetic study.

Science.gov (United States)

Reddy, Naveen Admala; Adusumilli, Gopinath; Devanna, Raghu; Pichai, Saravanan; Rohra, Mayur Gobindram; Arjunan, Sharmila

2013-10-01

Non Syndromic tooth agenesis is a congenital anomaly with significant medical, psychological and social ramifications. There is sufficient evidence to hypothesize that locus for this condition can be identified by candidate genes. The aim of this study was to test whether MSX1 671 T>C gene variant was involved in etiology of Non Syndromic tooth agenesis in Raichur Patients. Blood samples were collected with informed consent from 50 subjects having Non Syndromic tooth agenesis and 50 controls. Genomic DNA was extracted from the blood samples, Polymerase Chain Reaction was performed (PCR) and Restriction Fragment Length Polymorphism (RFLP) was performed for digestion products that were evaluated. The RESULTS showed positive correlation between MSX1671 T>C gene variant and Non Syndromic tooth agenesis in Raichur Patients. MSX1 671 T>C gene variant may be a good screening marker for Non Syndromic tooth agenesis in Raichur Patients . How to cite this article:Reddy NA, Adusumilli G, Devanna R, Pichai S, Rohra MG, Arjunan S. Msx1 Gene Variant - Its Presence in Tooth Absence - A Case Control Genetic Study. J Int Oral Health 2013; 5(5):20-6.

Uneven distribution of enamel in the tooth crown of a Plains Zebra (Equus quagga

Directory of Open Access Journals (Sweden)

Daniela E. Winkler

2015-06-01

Full Text Available Unworn teeth of herbivorous mammals are not immediately functional. They have to be partially worn to expose enamel ridges which can then act as shear-cutting blades to break the food down. We use the Plains Zebra (Equus quagga as a hypsodont, herbivorous model organism to investigate how initial wear of the tooth crown is controlled by underlying structures. We find that the enamel proportion is smaller at the apical half of the tooth crown in all upper tooth positions and suggest that lower enamel content here could promote early wear. Besides this uneven enamel distribution, we note that the third molar has a higher overall enamel content than any other tooth position. The M3 is thus likely to have a slightly different functional trait in mastication, resisting highest bite forces along the tooth row and maintaining functionality when anterior teeth are already worn down.

Uneven distribution of enamel in the tooth crown of a Plains Zebra (Equus quagga).

Science.gov (United States)

Winkler, Daniela E; Kaiser, Thomas M

2015-01-01

Unworn teeth of herbivorous mammals are not immediately functional. They have to be partially worn to expose enamel ridges which can then act as shear-cutting blades to break the food down. We use the Plains Zebra (Equus quagga) as a hypsodont, herbivorous model organism to investigate how initial wear of the tooth crown is controlled by underlying structures. We find that the enamel proportion is smaller at the apical half of the tooth crown in all upper tooth positions and suggest that lower enamel content here could promote early wear. Besides this uneven enamel distribution, we note that the third molar has a higher overall enamel content than any other tooth position. The M3 is thus likely to have a slightly different functional trait in mastication, resisting highest bite forces along the tooth row and maintaining functionality when anterior teeth are already worn down.

Lip and tooth injuries at public swimming pools in Austria.

Science.gov (United States)

Lechner, Katharina; Connert, Thomas; Kühl, Sebastian; Filippi, Andreas

2017-06-01

There is an increased risk of orofacial injuries in swimming pool facilities. Nevertheless, only a few studies have addressed this issue. The aim of this study was to identify the frequency of lip and tooth injuries at public swimming pools in Austria. A further aim was to examine which gender and age groups were affected, where and why these injuries occurred, and whether pool attendants had sufficient knowledge of dental first-aid measures. A total of 764 pool attendants in Austria were contacted by telephone and 689 participated in the study (90.2%). The attendants were interviewed retrospectively about accident occurrences in 2014 by a standardized questionnaire. Responses to the provision of first aid and choice of storage medium for avulsed teeth were subsequently evaluated. The frequency of lip injuries was 19.0%, and tooth injuries were 11.3%. Male bathers (P < .05) and children under 12 years (P < .001) most frequently suffered injuries. The waterslide was the most common accident site. The most common cause of lip injuries was slipping on wet surfaces (39.0%), and for tooth injuries it was collisions with other persons or objects (each 28.1%). The pool attendants' responses were predominantly good or sufficient on first aid, with the exception of what storage medium to choose. Tooth rescue boxes were available in only 8.6% of all pool facilities. Orofacial injuries are a frequently occurring problem in swimming pool facilities. The pool attendants' knowledge on first-aid care of tooth injuries could still be improved. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Is the relative increase in income inequality related to tooth loss in middle-aged adults?

Science.gov (United States)

Goulart, Mariél de Aquino; Vettore, Mario Vianna

2016-01-01

To assess whether Brazilian middle-aged adults living in cities that experienced a relative increase on income inequality were more likely to have severe tooth loss and lack a functional dentition. Data on Brazilian adults aged 35-44 years from state capitals and Federal District from the 2010 Brazilian Oral Health Survey (SBBrasil 2010) were analyzed. Clinically assessed tooth loss outcomes were severe tooth loss (Income inequality was assessed by Gini Index in 1991, 2000, and 2003 using tertiles of distribution. Variation in Gini Index was assessed by changes in the tertiles distribution between years. Multilevel logistic regression models were used to estimate odds ratios (ORs) and 95 percent confidence intervals (95 percent CI) between variation in income inequality and tooth loss outcomes adjusting for individual socio-demographic characteristics. Prevalence of severe tooth loss and lack of functional dentition was 4.8 percent and 21.2 percent, respectively. Individuals living in cities with moderate and high increase in income inequality between 1991 and 2003 were more likely to have severe tooth loss and lack a functional dentition in 2010 compared with those living in cities with stable income inequality in the same period. Relationships between low family income and both tooth loss outcomes were significantly attenuated by relative increases in income inequality. Relative increases in income inequality were significantly associated with severe tooth loss and lack of a functional dentition in Brazilian middle-aged adults. © 2015 American Association of Public Health Dentistry.

Tooth loss strongly associates with malnutrition in chronic kidney disease.

Science.gov (United States)

Ioannidou, E; Swede, H; Fares, G; Himmelfarb, J

2014-07-01

In chronic kidney disease (CKD), inadequate nutritional intake, inflammation, and increased oxidative stress have been the major contributing factors in malnutrition pathogenesis. However, there is still a paucity of evidence assessing the magnitude of the effect of tooth loss on malnutrition in CKD populations. The authors hypothesize that among patients with CKD, tooth loss may affect nutritional status, using the National Health and Nutrition Examination Survey 1988 to 1994 (NHANES III). Glomerular filtration rate (GFR) was estimated based on cystatin C levels using the relevant equation. Urinary albumin-to-creatinine ratio (albuminuria) was calculated in milligrams per gram with a cutoff point of 30 mg/g. CKD was defined based on estimated GFR protein and caloric intake (P = 0.02 and 0.01, respectively). Serum albumin reached a frequency peak in the fully edentulous group without dentures (group 4, 19.2%). In the same group, individuals had lower protein (30.1%) and caloric intake (30.2%) (P = 0.01 and 0.02, respectively). Furthermore, logistic regression analysis confirmed the significant role of tooth loss on serum albumin and protein and energy intake in this population even after adjusting for confounding variables. Tooth loss independently predicts low energy and protein intake, as well as serum albumin levels, biomarkers of malnutrition in CKD.

Replacement of missing tooth in esthetic zone with implant-supported fixed prosthesis

Directory of Open Access Journals (Sweden)

Sunil Kumar Mishra

2017-01-01

Full Text Available In the anterior region, the common reason for tooth loss is due to traumatic injury or congenital anomaly. Loss of a single tooth may cause functional and esthetic deficits to the patient. There are different treatment options available for replacing a missing incisor. Implant dentistry should be considered as first treatment alternative for replace a missing tooth. This case report presents the replacement of a missing maxillary left central incisor in a compromised site with dental implants along with bone graft followed by frenectomy to obtain a good clinical result and for better function and esthetics of the patient.

Charcot-Marie-Tooth disease.

LENUS (Irish Health Repository)

Reilly, Mary M

2011-03-01

Charcot-Marie-Tooth (CMT) disease is the commonest inherited neuromuscular disorder affecting at least 1 in 2,500. Over the last two decades, there have been rapid advances in understanding the molecular basis for many forms of CMT with more than 30 causative genes now described. This has made obtaining an accurate genetic diagnosis possible but at times challenging for clinicians. This review aims to provide a simple, pragmatic approach to diagnosing CMT from a clinician\\'s perspective.

Effects of carbonated soft drink consumption on orthodontic tooth movements in rats.

Directory of Open Access Journals (Sweden)

Hossein Agha Aghili

2014-04-01

Full Text Available The aim of this animal study was to evaluate the possible effects of Carbonated Soft Drink consumption on the rate of orthodontic tooth movement in rats.Thirty-six adult male Sprague-Dawley rats were randomly divided into two experimental groups and one control group. In the experimental groups (A&B, the water in the dietary regimen was replaced with soft drinks (Fanta® in group A and Cola® in group B two weeks before placement of orthodontic appliances. Then 5-mm nickel-titanium closed-coil springs were placed between the maxillary right first molars and first incisors under general anesthesia. This regimen continued for two weeks more and animals drank soft drink ad libitum. At the end of the experimental period, the rats were sacrificed, and interproximal tooth movements were measured.The mean amounts of tooth movement were 0.19mm in group A, 0.22mm in group B and 0.37mm in group C. Statistical analysis with analysis of variance (ANOVA test showed significant differences between all groups. The least movement occurred in group A that had received Fanta® drink.CSDs consumption decreases the rate of orthodontic tooth movement. The role of soft drinks in decreasing tooth movement might be related to its effects on bone metabolism.

A systematic review of the consequences of premature birth on palatal morphology, dental occlusion, tooth-crown dimensions, and tooth maturity and eruption.

Science.gov (United States)

Paulsson, Liselotte; Bondemark, Lars; Söderfeldt, Björn

2004-04-01

This systematic review addresses the question whether prematurity results in alteration of palatal morphology, dental occlusion, tooth-crown dimensions, and tooth maturation. A literature survey from the PubMed database covering the period from January 1966 to November 2002 used the Medical Subject Headings terms "infant, premature," and "infant, low birth weight" in combination with "jaws," "dental physiology," "dentition," and "tooth abnormalities." Controlled studies written in English and with definitions of premature birth according to the World Health Organization were selected. Two reviewers selected and extracted the data independently and also assessed the quality of the studies. The search strategy resulted in 113 articles, of which 13 met the inclusion criteria. Scientific evidence was found for altered palatal morphology in the short term among the premature children, and oral intubation was a contributing factor to the alterations. If corrected age was considered for the premature children, no delay in dental development and eruption was found compared with normally born children. Thus, the early birth of premature children must be taken in account when planning for orthodontic treatment. Because of the contradictory results and lack of longitudinal studies, the scientific evidence was too weak to answer the questions whether premature birth causes permanent alteration of palatal morphology, alteration of dental occlusion, and altered tooth-crown dimensions. To answer these questions and obtain reliable scientific evidence whether premature children are at risk for malocclusions from possible alterations of palatal morphology such as asymmetry and high arched palates, further well-designed controlled studies as well as longitudinal studies are needed.

Causes and pattern of tooth loss in children and adolescents in a ...

African Journals Online (AJOL)

Information obtained included age, gender, missing and extracted teeth, and reasons for extraction/tooth loss. Exfoliated primary teeth and congenitally missing teeth were excluded. Data was analysed using Epi info 2007 statistical software. Chi-square test was used to compare proportions of tooth loss among age groups.

Three-dimensional analysis of tooth dimensions in the MSX1-missense mutation

NARCIS (Netherlands)

Creton, M.; Boogaard, M.J. van den; Maal, T.J.; Verhamme, L.M.; Fennis, W.M.M.; Carels, C.E.L.; Kuijpers-Jagtman, A.M.; Cune, M.

2013-01-01

OBJECTIVES: A novel, 3D technique to measure the differences in tooth crown morphology between the MSX1 cases and non-affected controls was designed to get a better understanding of dental phenotype-genotype associations. MATERIALS AND METHODS: Eight Dutch subjects from a single family with tooth

TOOTH COLOR AND REFLECTANCE AS RELATED TO LIGHT-SCATTERING AND ENAMEL HARDNESS

NARCIS (Netherlands)

TENBOSCH, JJ; COOPS, JC

Tooth color is determined by the paths of light inside the tooth and absorption along these paths. This paper tests the hypothesis that, since the paths are determined by scattering, a relation between color and scattering coefficients exists. One hundred and two extracted incisors were fixed in

Measurement of opalescence of tooth enamel.

Science.gov (United States)

Lee, Yong-Keun; Yu, Bin

2007-08-01

Opalescent dental esthetic restoratives look natural and esthetic in any light, react to light in the same manner as the natural tooth and show improved masking effect. The objective of this study was to determine the opalescence of tooth enamel with reflection spectrophotometers. Color of intact bovine and human enamel was measured in the reflectance and transmittance modes. Two kinds of spectrophotometers were used for bovine and one kind was used for human enamel. The opalescence parameter (OP) was calculated as the difference in yellow-blue color coordinate (CIE Deltab(*)) and red-green color coordinate (CIE Deltaa(*)) between the reflected and transmitted colors. Mean OP value of bovine enamel was 10.6 (+/-1.4) to 19.0 (+/-2.1), and varied by the configuration of spectrophotometers. Mean OP value of human enamel was 22.9 (+/-1.9). Opalescence varied by the configuration of measuring spectrophotometer and the species of enamel. These values could be used in the development of esthetic restorative materials.

Gear Fault Detection Effectiveness as Applied to Tooth Surface Pitting Fatigue Damage

Science.gov (United States)

Lewicki, David G.; Dempsey, Paula J.; Heath, Gregory F.; Shanthakumaran, Perumal

2010-01-01

A study was performed to evaluate fault detection effectiveness as applied to gear-tooth-pitting-fatigue damage. Vibration and oil-debris monitoring (ODM) data were gathered from 24 sets of spur pinion and face gears run during a previous endurance evaluation study. Three common condition indicators (RMS, FM4, and NA4 [Ed. 's note: See Appendix A-Definitions D were deduced from the time-averaged vibration data and used with the ODM to evaluate their performance for gear fault detection. The NA4 parameter showed to be a very good condition indicator for the detection of gear tooth surface pitting failures. The FM4 and RMS parameters perfomu:d average to below average in detection of gear tooth surface pitting failures. The ODM sensor was successful in detecting a significant 8lDOunt of debris from all the gear tooth pitting fatigue failures. Excluding outliers, the average cumulative mass at the end of a test was 40 mg.

Epi-detected quadruple-modal nonlinear optical microscopy for label-free imaging of the tooth

Energy Technology Data Exchange (ETDEWEB)

Wang, Zi; Zheng, Wei; Huang, Zhiwei, E-mail: biehzw@nus.edu.sg [Optical Bioimaging Laboratory, Department of Biomedical Engineering, Faculty of Engineering, National University of Singapore, Singapore 117576 (Singapore); Stephen Hsu, Chin-Ying [Department of Dentistry, Faculty of Dentistry, National University of Singapore and National University Health System, Singapore 119083 (Singapore)

2015-01-19

We present an epi-detected quadruple-modal nonlinear optical microscopic imaging technique (i.e., coherent anti-Stokes Raman scattering (CARS), second-harmonic generation (SHG), third-harmonic generation (THG), and two-photon excited fluorescence (TPEF)) based on a picosecond (ps) laser-pumped optical parametric oscillator system for label-free imaging of the tooth. We demonstrate that high contrast ps-CARS images covering both the fingerprint (500–1800 cm{sup −1}) and high-wavenumber (2500–3800 cm{sup −1}) regions can be acquired to uncover the distributions of mineral and organic biomaterials in the tooth, while high quality TPEF, SHG, and THG images of the tooth can also be acquired under ps laser excitation without damaging the samples. The quadruple-modal nonlinear microscopic images (CARS/SHG/THG/TPEF) acquired provide better understanding of morphological structures and biochemical/biomolecular distributions in the dentin, enamel, and the dentin-enamel junction of the tooth without labeling, facilitating optical diagnosis and characterization of the tooth in dentistry.

Comparative analyses of tooth wear in free-ranging and captive wild equids.

Science.gov (United States)

Taylor, L A; Müller, D W H; Schwitzer, C; Kaiser, T M; Castell, J C; Clauss, M; Schulz-Kornas, E

2016-03-01

Captive breeding has played a crucial role in the conservation of threatened equid species. Grazing ruminants and rhinoceros in captivity have less abrasion-dominated tooth wear than their free-ranging conspecifics, with potential negative consequences for their health. However, a similar study on wild equids in captivity is missing. The aim was to establish if different tooth wear patterns are exhibited by free-ranging and captive equids. Cross-sectional study of museum specimens comparing free-ranging and captive equids. Dental casts of maxillary cheek teeth of 228 museum specimens (122 from free-ranging and 106 from captive individuals) of 7 wild equid species were analysed using the extended mesowear method. Although teeth showing specific abnormalities were not scored, the presence of focal overgrowths (hooks) of the rostral premolars (106, 206) was recorded. Captive Equus ferus przewalskii, E. grevyi, E. hemionus, E. quagga boehmi and E. zebra hartmannae have less abrasion-dominated tooth wear on their premolars than their free-ranging conspecifics (P<0.001). Fewer differences were exhibited between populations in the molars. No differences were exhibited in the distal cusp of the molars (110, 210) between populations, except in a small sample of E. kiang. Captive equids exhibited more homogeneous wear along the tooth row whereas free-ranging equids exhibited a tooth wear gradient, with more abrasion on premolars than molars. There were more rostral hooks on the premolars (106, 206) in the captive than the free-ranging population (P = 0.02). Captive equids did experience less abrasion-dominated tooth wear than their free-ranging conspecifics, but the differences in tooth wear were less pronounced than those between captive and free-ranging wild ruminant and rhinoceros species. This indicates that feeding regimes for captive equids deviate less from natural diets than those for captive ruminants and rhinoceros but that factors leading to hook

Influence of medication on the rate of orthodontic tooth movement (Part 1: hormons and corticosteroids

Directory of Open Access Journals (Sweden)

Mirhashemi Amirhossein

2015-05-01

Full Text Available The aim of this review article was to define the mechanism of action and effects of commonly used medications on the tissue remodeling and Orthodontic Tooth Movement (OTM. A review on the effects of medications and dietary supplements on the rate of experimental tooth movement was performed using Cochrane library, Embase and medline (1980-2013. 63 articles were included in this review. 34 of them were related to the effects of hormones and analgesics, were evaluated in this article but their interpretation was hindered by the variability in experimental design, magnitude of force applied during tooth movement and medication regimens. Non Steroidal Anti-Inflammatory Drugs (NSAIDs reduced the rate of tooth movement while non-NSAIDs such as acetaminophen had no effect on the rate of OTM. Corticosteroids, parathyroid hormone and thyroxin increased the rate of tooth movement. Sturgeons might slow OTM, but experimental studies are lacking. Medications might have an important influence on the rate of tooth movement and information on their consumption is necessary to adequately discuss treatment planning with patients.

Tooth loss early in life suppresses neurogenesis and synaptophysin expression in the hippocampus and impairs learning in mice.

Science.gov (United States)

Kubo, Kin-Ya; Murabayashi, Chika; Kotachi, Mika; Suzuki, Ayumi; Mori, Daisuke; Sato, Yuichi; Onozuka, Minoru; Azuma, Kagaku; Iinuma, Mitsuo

2017-02-01

Tooth loss induced neurological alterations through activation of a stress hormone, corticosterone. Age-related hippocampal morphological and functional changes were accelerated by early tooth loss in senescence-accelerated mouse prone 8 (SAMP8). In order to explore the mechanism underlying the impaired hippocampal function resulting from early masticatory dysfunction due to tooth loss, we investigated the effects of early tooth loss on plasma corticosterone levels, learning ability, neurogenesis, and synaptophysin expression in the hippocampus later in life of SAMP8 mice. We examined the effects of tooth loss soon after tooth eruption (1 month of age) on plasma corticosterone levels, learning ability in the Morris water maze, newborn cell proliferation, survival and differentiation in the hippocampal dentate gyrus, and synaptophysin expression in the hippocampus of aged (8 months of age) SAMP8 mice. Aged mice with early tooth loss exhibited increased plasma corticosterone levels, hippocampus-dependent learning deficits in the Morris water maze, decreased cell proliferation, and cell survival in the dentate gyrus, and suppressed synaptophysin expression in the hippocampus. Newborn cell differentiation in the hippocampal dentate gyrus, however, was not affected by early tooth loss. These findings suggest that learning deficits in aged SAMP8 mice with tooth loss soon after tooth eruption are associated with suppressed neurogenesis and decreased synaptophysin expression resulting from increased plasma corticosterone levels, and that long-term tooth loss leads to impaired cognitive function in older age. Copyright © 2016. Published by Elsevier Ltd.

Three-dimensional analysis of tooth dimensions in the MSX1-missense mutation

NARCIS (Netherlands)

Creton, Marijn; van den Boogaard, Marie-Jose; Maal, Thomas; Verhamme, Luc; Fennis, Willem; Carels, Carine; Kuijpers-Jagtman, Anne Marie; Cune, Marco

A novel, 3D technique to measure the differences in tooth crown morphology between the MSX1 cases and non-affected controls was designed to get a better understanding of dental phenotype-genotype associations. Eight Dutch subjects from a single family with tooth agenesis, all with an established

Recent Approaches in Tooth Engineering Research

Czech Academy of Sciences Publication Activity Database

Švandová, Eva; Veselá, Barbora; Křivánek, J.; Hampl, A.; Matalová, Eva

2014-01-01

Roč. 60, Suppl 1 (2014), s. 21-29 ISSN 0015-5500 R&D Projects: GA ČR GAP304/11/1418; GA MZd(CZ) NT11420 Institutional support: RVO:67985904 Keywords : engineering * tooth * stem cells * culture techniques Subject RIV: EA - Cell Biology Impact factor: 1.000, year: 2014

Comparison of Three types of Tooth Brushes on Plaque and Gingival Indices: A Randomized Clinical Trial.

Science.gov (United States)

Moeintaghavi, Amir; Sargolzaie, Naser; Rostampour, Mehrnoosh; Sarvari, Sara; Kargozar, Sanaz; Gharaei, Shideh

2017-01-01

To compare clinical results of three types of manual tooth brushes on plaque removal efficacy and gingivitis. This study is a single blind randomized trial with crossover design which involved 30 periodontaly healthy individuals. Professional plaque removal and oral hygiene instruction were performed for all the participants in the first step of our study followed by asking them to avoid brushing for 2 days. Thereafter plaque and gingivitis scores were measured using plaque and gingival indices (PI and GI). Then subjects were instructed to use Pulsar tooth brush for a two-week period and then, GI and PI indices were assessed again. After passing one-week period for wash out, subjects didn't brush for 2 days and indices were recorded again. The same procedure was done for CrossAction, and Butler 411 tooth brushes respectively and at the end of the study these variables were analyzed using SPSS software ver.16. Repeated measurement ANOVA test was used to compare the scores between different brushes. Finding of this study reveals that using all three types of tooth brushes resulted in significant plaque and gingivitis reduction compared to baseline levels. Pulsar tooth brush was significantly more effective in diminishing PI and GI than Butler tooth brush (p=0.044 and 0.031 respectively). According to our findings all 3 types of tooth brushes are effective in reduction of plaque and gingivitis and this reduction is significantly greater for Pulsar tooth brush compared to Butler and CrossAction tooth brushes.

Clinical evaluation of two-stage mandibular wisdom tooth extraction method to avoid mental nerve paresthesia

International Nuclear Information System (INIS)

Nozoe, Etsuro; Nakamura, Yasunori; Okawachi, Takako; Ishihata, Kiyohide; Shinnakasu, Mana; Nakamura, Norifumi

2011-01-01

Clinical courses following two-stage mandibular wisdom tooth extraction (TMWTE) carried out for preventing postoperative mental nerve paresthesia (MNP) were analyzed. When panoramic X-ray showed overlapping of wisdom tooth root on the superior 1/2 or more of the mandibular canal, interruption of the white line of the superior wall of the canal, or diversion of the canal, CT examination was facilitated. In cases where contact between the tooth root and canal was demonstrated in CT examination, TMWTE was then selected after gaining the patient's consent. TMWTE consisted of removing more than a half of the tooth crown and tooth root extraction at the second step after 2-3 months. The clinical features of wisdom teeth extracted and postoperative courses including tooth movement and occurrence of MNP during two-stage MWTE were evaluated. TMWTE was carried out for 40 teeth among 811 wisdom teeth (4.9%) that were extracted from 2007 to 2009. Among them, complete procedures were accomplished in 39 teeth, and crown removal was performed insufficiently at the first-stage operation in one tooth. Tooth movement was detected in 37 of 40 cases (92.5%). No postoperative MNP was observed in cases in which complete two-stage MWTE was carried out, but one case with insufficient crown removal was complicated by postoperative MNP. Seven mild complications (dehiscence, cold sensitivity, etc.) were noted after the first-stage operation. Therefore, we conclude that TMWTE for high-risk cases assessed by X-ray findings is useful to avoid MNP after MWTE. (author)

Family income and tooth decay in US children: does the association change with age?

Science.gov (United States)

Bernabé, E; Delgado-Angulo, E K; Murasko, J E; Marcenes, W

2012-01-01

This study explored whether the association of family income with tooth decay changes with age among children in the United States. A second objective was to explore the role of access to dental health care services in explaining the interrelationships between family income, child age and tooth decay. Data from 7,491 2- to 15-year-old children who participated in the 1999-2004 National and Health and Nutrition Examination Survey were analyzed. The association of family income with the prevalence of tooth decay in primary, permanent and primary or permanent teeth was first estimated in logistic regression models with all children, and then, separately in four age groups that reflect the development of the dentition (2-5, 6-8, 9-11 and 12-15 years, respectively). Findings showed that the income gradient in tooth decay attenuated significantly in 9- to 11-year-olds only to re-emerge in 12- to 15-year-olds. The age profile of the income gradient in tooth decay was not accounted for by a diverse set of family and child characteristics. This is the first study providing some evidence for age variations in the income gradient in tooth decay among children in the United States. Copyright © 2012 S. Karger AG, Basel.

The safety of peroxide-containing at-home tooth whiteners.

Science.gov (United States)

Li, Yiming

2003-04-01

Scientific data from research conducted during the past decade have demonstrated the safety of the dentist-dispensed at-home whiteners containing 10% carbamide peroxide. There has been no evidence of systemic adverse effects associated with the proper use of these whitening systems. Most commonly observed local adverse effects are mild-to-moderate tooth sensitivity and/or gingival irritation, which usually do not prevent the patient from completing the whitening treatment. The sensitivity and irritation are transient in most cases, and they dissipate when the patient discontinues the use of the whitener. There is no evidence of any long-term consequences that have resulted from tooth sensitivity and/or gingival irritation. However, potential adverse effects may occur from inappropriate applications, abuses, or the use of inappropriate products. The risks of using at-home whiteners without a dentist's involvement, or using formulations with a higher peroxide content than recommended, are yet to be determined. To maximize benefits while minimizing potential risks, the author advises using at-home tooth whiteners under the supervision of a dental professional.

Tooth enamel dosimetric response to 2.8 MeV neutrons

Science.gov (United States)

Fattibene, P.; Angelone, M.; Pillon, M.; De Coste, V.

2003-03-01

Tooth enamel dosimetry, based on electron paramagnetic resonance (EPR) spectroscopy, is recognized as a powerful method for individual retrospective dose assessment. The method is mainly used for individual dose reconstruction in the epidemiological studies aimed at the radiation risk analysis. The study of the sensitivity of tooth enamel as a function of radiation quality is one of the main goals of the research in this field. In the present work, tooth enamel dose response in a monoenergetic neutron flux of 2.8 MeV, generated by the D-D reaction, was studied for in air and in phantom irradiations of enamel samples and of whole teeth. EPR measurements were complemented by Monte Carlo calculation and by gamma dose discrimination obtained with thermoluminescent and Geiger-Muller tube measurements. The 2.8 MeV neutrons to 60Co relative sensitivity was 0.33±0.08.

Tooth enamel dosimetric response to 2.8 MeV neutrons

International Nuclear Information System (INIS)

Fattibene, P.; Angelone, M.; Pillon, M.; De Coste, V.

2003-01-01

Tooth enamel dosimetry, based on electron paramagnetic resonance (EPR) spectroscopy, is recognized as a powerful method for individual retrospective dose assessment. The method is mainly used for individual dose reconstruction in the epidemiological studies aimed at the radiation risk analysis. The study of the sensitivity of tooth enamel as a function of radiation quality is one of the main goals of the research in this field. In the present work, tooth enamel dose response in a monoenergetic neutron flux of 2.8 MeV, generated by the D-D reaction, was studied for in air and in phantom irradiations of enamel samples and of whole teeth. EPR measurements were complemented by Monte Carlo calculation and by gamma dose discrimination obtained with thermoluminescent and Geiger-Muller tube measurements. The 2.8 MeV neutrons to 60 Co relative sensitivity was 0.33±0.08

Functional fixation of autotransplanted tooth germs by using bioresorbable membranes.

Science.gov (United States)

Gérard, Eric; Membre, Hervé; Gaudy, Jean-François; Mahler, Patrick; Bravetti, Pierre

2002-12-01

The purpose of this study was to evaluate the contribution of a bioresorbable membrane placement to the healing of immature teeth after autotransplantation of tooth buds. Six cases were selected: 2 transplantations of wisdom teeth, 2 for premolar agenesis, 1 for ectopia, and 1 premolar in an incisor position. The crown of each tooth germ and the marginal alveolar bone were covered with a resorbable membrane. The radicular edification was nearly complete, neither ankylosis nor inflammatory resorption was observable, the pulp vitality was preserved, and the periodontal integration was identical to that of other teeth. The membrane ensured contention and stabilization of the transplant, allowed functional stimulation, permitted protection of the coagulum and periodontal cells, and kept the epithelium at a distance. The transplantations of immature teeth were improved by the use of a resorbable membrane, which caused an optimal functional fixation of the transplanted tooth.

Patterns of Glycoconjugate Distribution during Molar Tooth Germ Development in Mice

Directory of Open Access Journals (Sweden)

AR. Varasteh

2007-09-01

Full Text Available Objective: The aim of the present study was to evaluate the structure and distribution of Glycoconjugates during molar tooth germ development in mice.Materials and Methods: Sixteen tooth germs were obtained from BALB/c mice embryos 15 to 18 days post-gestation and fixed in 10% formalin. After routine tissue processing, 5μm sections were cut and stained with BSA1-B4 and PNA using the lectin histochemical method. All slides were evaluated by light microscopy.Results: Both lectins showed positive reaction in the tooth germ but with spatiotemporal differences. During bell stage, the reaction was strong with BSA1-B4 but moderate with PNA. Strong PNA uptake was observed in the odontoblastic and ameloblastic nuclei alongwith the apical cytoplasm of the ameloblasts.Conclusion: Although the lectins that were used in the present study recognize the same terminal sugar residue, they reacted with different disaccharide sequences with various penaltomer sugars. Therefore it may be assumed that the pattern of affinity for different parts of the developing tooth germ such as ameloblasts and odontoblasts is different in various lectins.

Relationship between microhardness and fluorine contents on tooth enamel determined by PIGE analysis

International Nuclear Information System (INIS)

Ma, D.S.; Paik, D.I.; Park, D.Y.; Moon, H.S.; Chang, Y.I.; Kim, J.B.

1997-01-01

The remineralization effect of fluoride has been measured by surface microhardness on tooth enamel. The purpose of this study was to investigate the relationship between microhardness and fluorine concentration on tooth enamel. Twelve sound bovine enamel specimens were prepared and immersed in 0.05% NaF solution for 1, 3, 6, 24 and 36 hours, respectively. The concentration of fluorine in specimens were measured by PIGE analysis and surface microhardness of each specimen was measured by surface microhardness tester. Fluorine concentration was increased by immersing time. There was no change in microhardness of each specimen by fluorine content. The results of this study suggest that there was no relationship between the fluorine concentration and surface microhardness in sound tooth enamel. PIGE analysis can be used effectively to assess the remineralization effect of fluorine content in tooth enamel. (author)

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... Is My Child at Risk for Early Childhood Tooth Decay? What is a Composite Resin (White Filling)? How Do I Care for My Child's Baby Teeth? Learn what those dental words mean. The Life ...

Age estimation by pulp/tooth ratio in lower premolars by orthopantomography.

Science.gov (United States)

Cameriere, Roberto; De Luca, Stefano; Alemán, Inmaculada; Ferrante, Luigi; Cingolani, Mariano

2012-01-10

Accurate age estimation has always been a problem for forensic scientists, and apposition of secondary dentine is often used as an indicator of age. Since 2004, in order to examine patterns of secondary dentine apposition, Cameriere et al. have been extensively studying the pulp/tooth area ratio of the canines by panoramic and peri-apical X-ray images. The main aim of this paper is to examine the relationship between age and age-related changes in the pulp/tooth area ratio in monoradicular teeth, with the exception of canines, by orthopantomography. A total of 606 orthopantomograms of Spanish white Caucasian patients (289 women and 317 men), aged between 18 and 75 years and coming from Bilbao and Granada (Spain), was analysed. Regression analysis of age of monoradicular teeth indicated that the lower premolars were the most closely correlated with age. An ANCOVA did not show significant differences between men and women. Multiple regression analysis, with age as dependent variable and pulp/tooth area ratio as predictor, yielded several formulae. R(2) ranged from 0.69 to 0.75 for a single lower premolar tooth and from 0.79 to 0.86 for multiple lower premolar teeth. Depending on the available number of premolar teeth, the mean of the absolute values of residual standard error, at 95% confidence interval, ranged between 4.34 and 6.02 years, showing that the pulp/tooth area ratio is a useful variable for assessing age with reasonable accuracy. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Identification of a research protocol to study orthodontic tooth movement

Directory of Open Access Journals (Sweden)

Annalisa Dichicco

2014-06-01

Full Text Available Aim: The orthodontic movement is associated with a process of tissue remodeling together with the release of several chemical mediators in periodontal tissues. Each mediator is a potential marker of tooth movement and expresses biological processes as: tissue inflammation and bone remodeling. Different amounts of every mediator are present in several tissues and fluids of the oral cavity. Therefore, there are different methods that allow sampling with several degrees of invasiveness. Chemical mediators are also substances of different molecular nature, and multiple kind of analysis methods allow detection. The purpose of this study was to draft the best research protocol for an optimal study on orthodontic movement efficiency. Methods: An analysis of the international literature have been made, to identify the gold standard of each aspect of the protocol: type of mediator, source and method of sampling and analysis method. Results: From the analysis of the international literature was created an original research protocol for the study and the assessment of the orthodontic movement, by using the biomarkers of the tooth movement. Conclusions: The protocol created is based on the choice of the gold standard of every aspect already analyzed in the literature and in existing protocols for the monitoring of orthodontic tooth movement through the markers of tooth movement. Clinical trials re required for the evaluation and validation of the protocol created.

Radicular Cyst With Actinomycotic Infection in an Upper Anterior Tooth

Directory of Open Access Journals (Sweden)

Shuei-Kuen Tseng

2009-10-01

Full Text Available Actinomycosis is an infection caused by filamentous, branching, Gram-positive anaerobic bacteria. It rarely infects the jawbone. This case report describes a patient with a left maxillary central incisor with an apical lesion and actinomycotic infection. A 23-year-old male patient underwent conventional root canal treatment of tooth 21, in a local dental clinic for about 1 year. However, percussion pain and a sinus tract that originated from tooth 21 were still present after treatment. Nonsurgical root canal treatment of tooth 21 was performed again but failed to relieve the symptoms. Therefore, apicoectomy and retrograde filling of the apical root canal with mineral trioxide aggregate were carried out. Periradicular bony defect was grafted by biocompatible material, and postoperative antibiotics (250 mg amoxicillin were given three times daily for 5 days. Pathological examination of the removed periapical tissue showed a radicular cyst with actinomycosis. At the 9-month postoperative recall, the sinus tract had disappeared and radiographic examination showed healing of the apical lesion. Periradicular actinomycosis is one important reason for failure of nonsurgical endodontic treatment. Clinically, if the tooth shows a recurrent sinus tract and poor response to conventional root canal treatment combined with antibiotic control, apical actinomycotic infection should be highly suspected, and an alternative endodontic surgical approach is needed for successful treatment.

Tooth Morphogenesis and FGF4 Expression During Development of Molar Tooth in Three Muroid Rodents: Calomyscus elburzensis (Calomyscidae), Mesocricetus auratus (Cricetidae) and Mus musculus (Muridae).

Science.gov (United States)

Hamidi, Kordiyeh; Darvish, Jamshid; Matin, Maryam M; Javanmard, Athar Sadat; Kilpatrick, C William

2017-12-01

To date, no studies have examined the tooth formation during developmental stages of brush-tailed mice (Calomyscidae) and true hamsters (Cricetidae). Herein, we compared the timing of tooth morphogenesis and FGF4 expression pattern during development of the first lower molar in Goodwin's brush-tailed mouse, Calomyscus elburzensis with two other muroid rodents; the house mouse, Mus musculus (Muridae), model organism for tooth morphogenesis, and the golden hamster, Mesocricetus auratus which shares great similarities in cusp pattern with brush-tailed mice. All three species were bred in captivity and developing embryos were isolated at different embryonic days (E). Histological evaluation of lower molars was performed and spatiotemporal pattern of FGF4 expression was determined by immunohistochemistry. Results indicated that morphogenesis of the tooth cusps starts at the beginning of the cap stage of the first lower molar (E14 in house mouse, about E11.5 in golden hamster and E22 in Goodwin's brush-tailed mouse). During the cap to bell stage (E15 in house mouse, E12 in golden hamster and at about E24 in Goodwin's brush-tailed mouse), a decrease in the expression of FGF4 was observed in the mesenchyme, except for the cusp tips. According to our observations, the developmental process of the first lower molar formation in Goodwin's brush-tailed mouse began much later as compared with the other two species. Despite the differences in the temporal pattern of molar development between these three members of the same superfamily (Muroidea), the correlation in the expression of FGF4 with specific stages of tooth morphogenesis supported its regulatory function. Anat Rec, 300:2138-2149, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

The differences of orthodontic tooth movement on menstrual and ovulation cycle

Directory of Open Access Journals (Sweden)

Sonya Grecila Susilo

2014-12-01

Full Text Available Background: Estrogens are sex hormon that play an important role in bone metabolism, including in bone remodeling during orthodontic treatment. Women has a monthly cycle which is affected by fluctuations of estrogen that is menstruation and ovulation. Purpose: The study was aimed to determine the differences of orthodontic tooth movement during menstrual an ovulation cycle. Methods: Five women were given ± 100 g orthodontic force using fixed orthodontic appliance with straight wire technique at the time of menstruation and ovulation with an interval of 1.5 months. Orthodontic tooth movement and levels of estrogen were measured during menstruation and ovulation. Results: Statistical results showed a significant differences between estrogen levels and orthodontic tooth movement (p < 0.05. When estrogen levels decline as in menstruation, tooth movement as results of orthodontic force would increase, whereas when estrogen levels increase as the time of ovulation, tooth movement would decrease. Conclusion: The estrogen level in menstruation and ovulation cycle may affect the tooth movement on ortodontic treatment.Latar belakang: Estrogen merupakan hormon seks yang mempunyai peran penting dalam metabolisme tulang termasuk dalam remodeling tulang selama perawatan ortodonti. Wanita memiliki siklus bulanan yang dipengaruhi oleh fluktuasi estrogen yaitu menstruasi dan ovulasi. Tujuan: Penelitian ini bertujuan untuk mengetahui perbedaan pergerakan gigi akibat gaya ortodonti pada siklus menstruasi dan ovulasi. Metode: Lima orang wanita diberikan gaya ortodonti ±100 gr menggunakan alat orthodontik cekat dengan teknik straight wire pada saat menstruasi dan ovulasi dengan selang waktu 1,5 bulan. Selain itu subyek juga diukur kadar estrogennya saat menstruasi dan ovulasi. Hasil: Hasil statistik menunjukan kadar estrogen berbanding terbalik dengan pergerakan gigi ortodonti (p < 0,05. Saat kadar estrogen menurun seperti pada menstruasi, maka pergerakan gigi

Accuracy in tooth positioning with a fully customized lingual orthodontic appliance.

Science.gov (United States)

Grauer, Dan; Proffit, William R

2011-09-01

To understand orthodontic tooth movement, a method of quantification of tooth position discrepancies in 3 dimensions is needed. Brackets and wires now can be fabricated by CAD/CAM technology on a setup made at the beginning of treatment, so that treatment should produce a reasonably precise duplicate of the setup. The extent of discrepancies between the planned and actual tooth movements can be quantified by registration of the setup and final models. The goal of this study was to evaluate the accuracy of a CAD/CAM lingual orthodontic technique. Dental casts of 94 consecutive patients from 1 practice, representing a broad range of orthodontic problems, were scanned to create digital models, and then the setup and final models for each patient were registered individually for the maxillary and mandibular dental arches. Individual tooth discrepancies between the setup and actual outcome were computed and expressed in terms of a six-degrees-of-freedom rectangular coordinate system. Discrepancies in position and rotation between the setup and outcome were small for all teeth (generally less than 1 mm and 4°) except for the second molars, where some larger discrepancies were observed. Faciolingual expansion in the posterior teeth was greater in the setup than in the final models, especially at the second molars. Linear mixed models showed that age, type of tooth, jaw, initial crowding, time in slot-filling wire, use of elastics, days in treatment, interproximal reduction, and rebonding, were all influences on the final differences, but, for most of these factors, the influence was small, explaining only a small amount of the discrepancy between the planned and the actual outcomes. These fully customized lingual orthodontic appliances were accurate in achieving the goals planned at the initial setup, except for the full amount of planned expansion and the inclination at the second molars. This methodology is the first step toward understanding and measuring tooth

Preemptive use of etodolac on tooth sensitivity after in-office bleaching: a randomized clinical trial.

Science.gov (United States)

Vaez, Savil Costa; Faria-E-Silva, André Luís; Loguércio, Alessandro Dourado; Fernandes, Micaelle Tenório Guedes; Nahsan, Flávia Pardo Salata

2018-02-01

This study determined the effectiveness of the preemptive administration of etodolac on risk and intensity of tooth sensitivity and the bleaching effect caused by in-office bleaching using 35% hydrogen peroxide. Fifty patients were selected for this tripleblind, randomized, crossover, and placebo-controlled clinical trial. Etodolac (400 mg) or placebo was administrated in a single-dose 1 hour prior to the bleaching procedure. The whitening treatment with 35% hydrogen peroxide was carried out in two sessions with a 7-day interval. Tooth sensitivity was assessed before, during, and 24 hours after the procedure using the analog visual scale and the verbal rating scale. Color alteration was assessed by a bleach guide scale, 7 days after each session. Relative risk of sensitivity was calculated and adjusted by session, while overall risk was compared by the McNemar's test. Data on the sensitivity level of both scales and color shade were subjected to Friedman, Wilcoxon, and Mann-Whitney tests, respectively (α=0.05). The preemptive administration of etodolac did not affect the risk of tooth sensitivity and the level of sensitivity reported, regardless of the time of evaluation and scale used. The sequence of treatment allocation did not affect bleaching effectiveness, while the second session resulted in additional color modification. The preemptive administration of etodolac in a single dose 1 hour prior to in-office tooth bleaching did not alter tooth color, and the risk and intensity of tooth sensitivity reported by patients. A single-dose preemptive administration of 400 mg of etodolac did not affect either risk of tooth sensitivity or level of sensitivity reported by patients, during or after the in-office tooth bleaching procedure.

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... friv Home InfoBites Find an AGD Dentist Your Family's Oral Health About the AGD Dental care and ... a Tooth Home | InfoBites | Find a Dentist | Your Family's Oral Health | RSS About AGD | Contact AGD | Site ...

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... Contact InfoBites Quick Reference Learn more Children's Oral Health What is Baby Bottle Tooth Decay? Temporomandibular Joint ... Home | InfoBites | Find a Dentist | Your Family's Oral Health | RSS About AGD | Contact AGD | Site Map | Reprints ...

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... Contact InfoBites Quick Reference Learn more Children's Oral Health Check Menstrual Calendar for Tooth Extraction The History ... Home | InfoBites | Find a Dentist | Your Family's Oral Health | RSS About AGD | Contact AGD | Site Map | Reprints ...

Applying orthodontic tooth extrusion in a patient treated with bisphosphonate and irradiation: a case report.

Science.gov (United States)

Morita, Hiromitsu; Imai, Yuko; Yoneda, Masahiro; Hirofuji, Takao

2017-01-01

Bisphosphonates and irradiation are useful medical treatments, but can often cause oral complications such as medication-related oral necrosis of the jaw (MRONJ) and osteoradionecrosis (ORN) during oral surgery, including tooth extraction. Therefore, we should take all risks into consideration carefully before choosing dental treatment for patients with a medical history of such therapies. A 55-year-old woman who underwent cord blood transplantation to treat extranodal natural killer T (NK/T) cell lymphoma (nasal type IVB) had a medical history of bisphosphonate and irradiation treatments. We treated her residual tooth root by applying orthodontic extrusion to avoid extraction and successfully restored the tooth. Application of an orthodontic tooth extrusion technique for conservative treatment of a residual tooth is a useful means of avoiding MRONJ or ORN in patients who have a medical history of bisphosphonate and irradiation treatments. © 2016 Special Care Dentistry Association and Wiley Periodicals, Inc.

Natural tooth pontic with splinting of periodontally weakened teeth using fiber-reinforced composite resin

Directory of Open Access Journals (Sweden)

Gauri Srinidhi

2014-01-01

Full Text Available Replacement of missing anterior teeth due to periodontal reasons is challenging due to the poor support of abutment teeth. This prevents the use of fixed partial dentures (FPDs. Fiber-reinforced splinting provides a viable alternative to the dentist while choosing a treatment plan in replacing missing anterior teeth in periodontally compromised patients as opposed to conventional modalities like FPDs or removable partial dentures. Replacing missing teeth using either patient′s own tooth or a denture tooth as pontic can be done by splinting adjacent teeth with fiber reinforced composite. The splinting has an additional advantage of stabilizing adjacent mobile teeth. This case report details the case selection, procedure with follow-up of a case where the natural extracted tooth of the patient was used as pontic to replace a missing anterior tooth. The splinting was done with fiber reinforced composite resin. Fiber-reinforced composite resin splinting of patient′s extracted natural tooth is economical, fast, and easy to use chairside technique with the added benefit of periodontal stabilization.

Adult tooth loss for residents of US coal mining and Appalachian counties.

Science.gov (United States)

Hendryx, Michael; Ducatman, Alan M; Zullig, Keith J; Ahern, Melissa M; Crout, Richard

2012-12-01

The authors compared rates of tooth loss between adult residents of Appalachian coal-mining areas and other areas of the nation before and after control for covariate risks. The authors conducted a cross-sectional secondary data analysis that merged 2006 national Behavioral Risk Factor Surveillance System data (BRFSS) (N = 242 184) with county coal-mining data and other county characteristics. The hypothesis tested was that adult tooth loss would be greater in Appalachian mining areas after control for other risks. Primary independent variables included main effects for coal-mining present (yes/no) residence in Appalachia (yes/no), and their interaction. Data were weighted using the BRFSS final weights and analyzed using SUDAAN Proc Multilog to account for the multilevel complex sampling structure. The odds of two measures of tooth loss were examined controlling for age, race\\ethnicity, drinking, smoking, income, education, supply of dentists, receipt of dental care, fluoridation rate, and other variables. After covariate adjustment, the interaction variable for the residents of Appalachian coal-mining counties showed a significantly elevated odds for any tooth loss [odds ratio (OR) = 1.19, 95% CI = 1.02, 1.38], and greater tooth loss measured by a 4-level edentulism scale (OR = 1.20, 95% CI = 1.05, 1.36). The main effect for Appalachia was also significant for both measures, but the main effect for coal mining was not. Greater risk of tooth loss among adult residents of Appalachian coal-mining areas is present and is not explained by differences in reported receipt of dental care, fluoridation rates, supply of dentists or other behavioral or socioeconomic risks. Possible contributing factors include mining-specific disparities related to access, behavior or environmental exposures. © 2012 John Wiley & Sons A/S.

Economic evaluation of single-tooth replacement: dental implant versus fixed partial denture.

Science.gov (United States)

Kim, Younhee; Park, Joo-Yeon; Park, Sun-Young; Oh, Sung-Hee; Jung, YeaJi; Kim, Ji-Min; Yoo, Soo-Yeon; Kim, Seong-Kyun

2014-01-01

This study assessed the cost-effectiveness from a societal perspective of a dental implant compared with a three-unit tooth-supported fixed partial denture (FPD) for the replacement of a single tooth in 2010. A decision tree was developed to estimate cost-effectiveness over a 10-year period. The survival rates of single-tooth implants and FPDs were extracted from a meta-analysis of single-arm studies. Medical costs included initial treatment costs, maintenance costs, and costs to treat complications. Patient surveys were used to obtain the costs of the initial single-tooth implant or FPD. Maintenance costs and costs to treat complications were based on surveys of seven clinical experts at dental clinics or hospitals. Transportation costs were calculated based on the number of visits for implant or FPD treatment. Patient time costs were estimated using the number of visits and time required, hourly wage, and employment rate. Future costs were discounted by 5% to convert to present values. The results of a 10-year period model showed that a single dental implant cost US $261 (clinic) to $342 (hospital) more than an FPD and had an average survival rate that was 10.4% higher. The incremental cost-effectiveness ratio was $2,514 in a clinic and $3,290 in a hospital for a prosthesis in situ for 10 years. The sensitivity analysis showed that initial treatment costs and survival rate influenced the cost-effectiveness. If the cost of an implant were reduced to 80% of the current cost, the implant would become the dominant intervention. Although the level of evidence for effectiveness is low, and some aspects of single-tooth implants or FPDs, such as satisfaction, were not considered, this study will help patients requiring single-tooth replacement to choose the best treatment option.

The EPR investigation of tooth enamel for measurements of tooth enamel for measurements of absorbed gamma doses of people irradiated in Chernobyl accident

International Nuclear Information System (INIS)

Baran, N.P.; Barchuk, V.I.; Bar'yakhtar, V.G.; Bugaj, A.A.; Koval', G.N.; Maksimenko, V.M.; Berezhnoj, A.B.; Zakharash, M.P.; AN Ukrainskoj SSR, Kiev

1993-01-01

The EPR spectra of the tooth enamel of Chernobyl 'liquidators' were investigated. A lot of people were engaged in work at the Chernobyl area after the accident in 1986. A part of them is under regular medical control at the Ukrainian security service hospital. When patients lose the teeth for some reasons the EPR spectra of radiation centers in tooth enamel caused by emergency gamma radiation were investigated. The measurement of the intensities of the EPR spectra give the real individual absorbed doses of gamma radiation which are much higher than the official values registered in the medical cards of liquidators

The Third International Intercomparison on EPR Tooth Dosimetry: Part 2, final analysis

International Nuclear Information System (INIS)

Wieser, A.; Debuyst, R.; Fattibene, P.; Meghzifene, A.; Onori, S.; Bayankin, S. N.; Brik, A.; Bugay, A.; Chumak, V.; Ciesielski, B.; Hoshi, M.; Imata, H.; Ivannikov, A.; Ivanov, D.; Junczewska, M.; Miyazawa, C.; Penkowski, M.; Pivovarov, S.; Romanyukha, A.; Romanyukha, L.; Schauer, D.; Scherbina, O.; Schultka, K.; Sholom, S.; Skvortsov, V.; Stepanenko, V.; Thomas, J. A.; Tielewuhan, E.; Toyoda, S.; Trompier, F.

2006-01-01

The objective of the Third International Intercomparison on EPR Tooth Dosimetry was to evaluate laboratories performing tooth enamel dosimetry <300 mGy. Final analysis of results included a correlation analysis between features of laboratory dose reconstruction protocols and dosimetry performance. Applicability of electron paramagnetic resonance (EPR) tooth dosimetry at low dose was shown at two applied dose levels of 79 and 176 mGy. Most (9 of 12) laboratories reported the dose to be within 50 mGy of the delivered dose of 79 mGy, and 10 of 12 laboratories reported the dose to be within 100 mGy of the delivered dose of 176 mGy. At the high-dose tested (704 mGy) agreement within 25% of the delivered dose was found in 10 laboratories. Features of EPR dose reconstruction protocols that affect dosimetry performance were found to be magnetic field modulation amplitude in EPR spectrum recording, EPR signal model in spectrum deconvolution and duration of latency period for tooth enamel samples after preparation. (authors)

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... oyunlarý bakugan oyunlarý geta poker friv Home InfoBites Find an AGD Dentist Your Family's Oral Health About ... mean. The Life of a Tooth Home | InfoBites | Find a Dentist | Your Family's Oral Health | RSS About ...

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... 2018 About | Contact InfoBites Quick Reference Learn more Oral Health and Overal Health Headaches and Jaw Pain? Check ... Tooth Home | InfoBites | Find a Dentist | Your Family's Oral Health | RSS About AGD | Contact AGD | Site Map | Reprints ...

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... Bomberman atari oyunlarý bakugan oyunlarý geta poker friv Home InfoBites Find an AGD Dentist Your Family's Oral ... dental words mean. The Life of a Tooth Home | InfoBites | Find a Dentist | Your Family's Oral Health | ...

Retrospective Dosimetry: Dose Analysis From Tooth Enamel Using Electron Spin Resonance (ESR)

International Nuclear Information System (INIS)

Mohd Rodzi Ali; Rahimah Abdul Rahim; Noraisyah Yusof; Syed Asraf Fahlawi Wafa Syed Mohd Ghazi; Juliana Mahamad Napiah; Yahaya Talib; Rehir Dahalan

2014-01-01

The radiation dose should be accurately measured in order to relate its effect to the cells. The assessment of dose usually performed using biological dosimetry techniques. However, the reduction of lymphocytes (white blood cells) after the time period results in inaccuracy of dose measurement. An alternative method used is the application of Electron Spin Resonance (ESR) using tooth enamel. In this study, tooth enamels were evaluated and used to measure the individual absorbed dose from the background. The basic tooth features that would affect dose measurement were discussed. The results show this technique is capable and effective for retrospective dose measurement and useful for the study of radiation effect to human. (author)

Surgical management with intentional replantation on a tooth with palato-radicular groove

Directory of Open Access Journals (Sweden)

Jorge Forero-López

2015-05-01

Full Text Available A palato-radicular groove (PRG is a developmental anomaly primarily found in the maxillary lateral incisors. It is a potential communication path between the root canal and the periodontium that decreases the survival prognosis of the affected tooth, therefore compromising the stability of the dental structure in the oral cavity. The aim of this case report is to present an original technique where a PRG was treated by means of intracanal disinfection, PRG sealing with glass ionomer, replantation with intentional horizontal 180 degree rotation of the tooth, and an aesthetic veneer placed to provide adequate tooth morphology. The clinical and biological benefits of this novel technique are presented and discussed.

A saw-tooth plasma actuator for film cooling efficiency enhancement of a shaped hole

Science.gov (United States)

Li, Guozhan; Yu, Jianyang; Liu, Huaping; Chen, Fu; Song, Yanping

2017-08-01

This paper reports the large eddy simulations of the effects of a saw-tooth plasma actuator and the laidback fan-shaped hole on the film cooling flow characteristics, and the numerical results are compared with a corresponding standard configuration (cylindrical hole without the saw-tooth plasma actuator). For this numerical research, the saw-tooth plasma actuator is installed just downstream of the cooling hole and a phenomenological plasma model is employed to provide the 3D plasma force vectors. The results show that thanks to the downward force and the momentum injection effect of the saw-tooth plasma actuator, the cold jet comes closer to the wall surface and extends further downstream. The saw-tooth plasma actuator also induces a new pair of vortex which weakens the strength of the counter-rotating vortex pair (CRVP) and entrains the coolant towards the wall, and thus the diffusion of the cold jet in the crossflow is suppressed. Furthermore, the laidback fan-shaped hole reduces the vertical jet velocity causing the disappearance of downstream spiral separation node vortices, this compensates for the deficiency of the saw-tooth plasma actuator. Both effects of the laidback fan-shaped hole and the saw-tooth plasma actuator effectively control the development of the CRVP whose size and strength are smaller than those of the anti-counter rotating vortex pair in the far field, thus the centerline and the spanwise-averaged film cooling efficiency are enhanced. The average film cooling efficiency is the biggest in the Fan-Dc = 1 case, which is 80% bigger than that in the Fan-Dc = 0 case and 288% bigger than that in the Cyl-Dc = 0 case.

An Analysis of the Symptomatic Domains Most Relevant to Charcot Marie Tooth Neuropathy (CMT) Patients

Science.gov (United States)

2017-06-09

Charcot Marie Tooth Disease (CMT); Hereditary Sensory and Motor Neuropathy; Nerve Compression Syndromes; Tooth Diseases; Congenital Abnormalities; Genetic Diseases, Inborn; Heredodegenerative Disorders, Nervous System

Role of computer-based learning in tooth carving in dentistry: An Indian perspective.

Science.gov (United States)

Juneja, Saurabh; Juneja, Manjushree

2016-01-01

Tooth carving is an important practical preclinical exercise in the curriculum in Indian dental education setup. It forms the basis of introduction to tooth anatomy, morphology and occlusion of primary and permanent teeth through practical approach. It requires enormous time and manpower to master the skill. Therefore, there is an imminent necessity to incorporate computer-based learning of the art of tooth carving for effective teaching and efficient student learning. This will ensure quality time to be spent on other academic and research activities by students and faculty in addition to adding value as a teaching aid.

Primary cilia regulate Shh activity in the control of molar tooth number

Czech Academy of Sciences Publication Activity Database

Ohazama, A.; Haycraft, C. J.; Seppala, M.; Ghafoor, S.; Cobourne, M.; Martinelli, D. C.; Fan, CH. M.; Peterková, Renata; Lesot, H.; Yoder, B. K.; Sharpe, P. T.

2009-01-01

Roč. 136, č. 6 (2009), s. 897-903 ISSN 0950-1991 R&D Projects: GA ČR GA304/07/0223; GA MŠk OC B23.002 Institutional research plan: CEZ:AV0Z50390512 Keywords : intraflagellar transport * supernumerary tooth * tooth development Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 7.194, year: 2009

Rare Periodontal Ligament Drainage for Periapical Inflammation of an Adjacent Tooth: A Case Report and Review of the Literature

Directory of Open Access Journals (Sweden)

Hongmei Guo

2014-01-01

Full Text Available Aim. To report a case with an unusual drainage route of periapical inflammation exiting through the gingival sulcus of an adjacent vital tooth and review probable factors determining the diversity of the discharge routes of periapical inflammation. Summary. An 18-year-old male patient presented with periodontal abscess of tooth 46, which was found to be caused by a periapical cyst with an acute abscess of tooth 45. During endodontic surgery, a rarely reported drainage route for periapical inflammation via the gingival sulcus of an adjacent vital tooth was observed for the first time. Complete periodontal healing of the deep pocket of tooth 46 and hiding of the periapical cyst of tooth 45 followed after root canal treatment and periapical surgery with Bio-Oss Collagen implantation on tooth 45. The drainage routes of periapical inflammation are multivariate and the diversity of drainage pathways of periapical inflammation is mainly related to factors such as gravity, barriers against inflammation, and the causative tooth itself.

Epithelial topography for repetitive tooth formation

Directory of Open Access Journals (Sweden)

Marcia Gaete

2015-12-01

Full Text Available During the formation of repetitive ectodermally derived organs such as mammary glands, lateral line and teeth, the tissue primordium iteratively initiates new structures. In the case of successional molar development, new teeth appear sequentially in the posterior region of the jaw from Sox2+ cells in association with the posterior aspect of a pre-existing tooth. The sequence of molar development is well known, however, the epithelial topography involved in the formation of a new tooth is unclear. Here, we have examined the morphology of the molar dental epithelium and its development at different stages in the mouse in vivo and in molar explants. Using regional lineage tracing we show that within the posterior tail of the first molar the primordium for the second and third molar are organized in a row, with the tail remaining in connection with the surface, where a furrow is observed. The morphology and Sox2 expression of the tail retains characteristics reminiscent of the earlier stages of tooth development, such that position along the A-P axes of the tail correlates with different temporal stages. Sox9, a stem/progenitor cell marker in other organs, is expressed mainly in the suprabasal epithelium complementary with Sox2 expression. This Sox2 and Sox9 expressing molar tail contains actively proliferating cells with mitosis following an apico-basal direction. Snail2, a transcription factor implicated in cell migration, is expressed at high levels in the tip of the molar tail while E-cadherin and laminin are decreased. In conclusion, our studies propose a model in which the epithelium of the molar tail can grow by posterior movement of epithelial cells followed by infolding and stratification involving a population of Sox2+/Sox9+ cells.

Fused primary first mandibular macromolar with a unique relation to its permanent successors: A rare tooth anomaly.

Science.gov (United States)

Dhindsa, Abhishek; Garg, Shalini; Damle, S G; Opal, Shireen; Singh, Tavleen

2013-04-01

Dental anomalies of number and forms may occur in the primary and permanent dentition. Various terms have been used to describe dental twinning anomalies: Germination, fusion, concrescence, double teeth, conjoined teeth, twinned teeth, geminifusion, and vicinifusion. Fused tooth is a developmental anomaly that is seen more frequently in the primary than the permanent dentition. Double tooth involving deciduous anterior teeth is found mostly in the mandible. Very few cases of nonsyndromic double primary molar have been reported in the literature. The succeeding permanent tooth is often found missing congenitally in the same region. This article reports a very rare unilateral occurrence of an anomalous, primary mandibular first macromolar formed by fusion with a dysmorphic premolar like supernumerary tooth in deciduous dentition period. Instead of agenesis of succedaneous tooth, the double tooth has been succeeded by normally developing mandibular first premolar in the same region.

Tooth preparations for complete crowns: an art form based on scientific principles.

Science.gov (United States)

Goodacre, C J; Campagni, W V; Aquilino, S A

2001-04-01

No recent literature has reviewed the current scientific knowledge on complete coverage tooth preparations. This article traces the historic evolution of complete coverage tooth preparations and identifies guidelines for scientific tooth preparations. Literature covering 250 years of clinical practice was reviewed with emphasis on scientific data acquired during the last 50 years. Both a MEDLINE search and an extensive manual search were used to locate relevant articles written in English in the last 50 years. Teeth should be prepared so that they exhibit the following characteristics: 10 to 20 degrees of total occlusal convergence, a minimal occlusocervical dimension of 4 mm for molars and 3 mm for other teeth, and an occlusocervical-to-faciolingual dimension ratio of 0.4 or greater. Facioproximal and linguoproximal line angles should be preserved whenever possible. When the above features are missing, the teeth should be modified with auxiliary resistance features such as axial grooves or boxes, preferably on proximal surfaces. Finish line selection should be based on the type of crown/retainer, esthetic requirements, ease of formation, and personal experience. Expectations of enhanced marginal fit with certain finish lines could not be validated by recent research. Esthetic requirements and tooth conditions determine finish line locations relative to the gingiva, with a supragingival location being more acceptable. Line angles should be rounded, and a reasonable degree of surface smoothness is desired. Nine scientific principles have been developed that ensure mechanical, biologic, and esthetic success for tooth preparation of complete coverage restorations.

Periodontal CGRP contributes to orofacial pain following experimental tooth movement in rats.

Science.gov (United States)

Long, Hu; Liao, Lina; Gao, Meiya; Ma, Wenqiang; Zhou, Yang; Jian, Fan; Wang, Yan; Lai, Wenli

2015-08-01

Calcitonin-related gene peptide (CGRP) plays an important role in orofacial inflammatory pain. The aim of this study was to determine whether periodontal CGRP contributes to orofacial pain induced by experimental tooth movement in rats. Male Sprague-Dawley rats were used in this study. Closed coil springs were used to deliver forces. Rats were euthanized on 0d, 1d, 3d, 5d, 7d, and 14d following experimental tooth movement. Then, alveolar bones were obtained for immunostaining of periodontal tissues against CGRP. Two hours prior to euthanasia on each day, orofacial pain levels were assessed through rat grimace scale. CGRP and olcegepant (CGRP receptor antagonist) were injected into periodontal tissues to verify the roles of periodontal CGRP in orofacial pain induced by experimental tooth movement. Periodontal CGRP expression levels and orofacial pain levels were elevated on 1d, 3d, 5d, and 7d following experimental tooth movement. The two indices were significantly correlated with each other and fitted into a dose-response model. Periodontal administration of CGRP could elevate periodontal CGRP expressions and exacerbate orofacial pain. Moreover, olcegepant administration could decrease periodontal CGRP expressions and alleviate orofacial pain. Therefore, periodontal CGRP plays an important role in pain transmission and modulation following experimental tooth movement. We suggest that it may participate in a positive feedback aiming to amplify orofacial pain signals. Copyright © 2015 Elsevier B.V. All rights reserved.

Tooth mobility changes subsequent to root fractures

DEFF Research Database (Denmark)

Andreasen, Jens Ove; Christensen, Søren Steno Ahrensburg; Tsilingaridis, Georgios

2012-01-01

The purpose of this study was to analyze tooth mobility changes in root-fractured permanent teeth and relate this to type of interfragment healing (hard tissue healing (HT), interfragment healing with periodontal ligament (PDL) and nonhealing with interposition of granulation tissue (GT) because...

The use of different analgesics in orthodontic tooth movements.

Science.gov (United States)

Hammad, Shaza M; El-Hawary, Yousry M; El-Hawary, Amira K

2012-09-01

To provide a semi-quantitative assessment of the effect of different analgesics (celecoxib, ketorolac, and paracetamol) on tooth movement and bone resorption using immunohistochemical staining of matrix metalloproteinase-13 (MMP-13). Forty white male rats (12-weeks old; body weight: 230-250 g) were divided into four groups (10 rats each) and were given the treatment once a day for 2 consecutive months. Group A (control group) rats were given the reverse osmosis water; group B rats were given 10 mg/kg celecoxib; group C rats were given 3 mg/kg ketorolac; and group D rats were given 150 mg/kg paracetamol. A precalibrated closed Sentalloy coil spring was placed inside each rat mouth to deliver a constant force of 50 cN. The magnitude of tooth movement was measured intraorally. After 2 months, the rats were sacrificed, and the sections were mounted on L-polylysine-coated glass slides. Slides from each specimen were stained with hematoxylin and eosin, and others were stained with MMP-13. Data were analyzed with the one-way analysis of variance (ANOVA). Celecoxib, ketorolac, and paracetamol groups showed tooth movement of 1.81 ± 0.43 mm, 1.13 ± 0.28 mm, and 1.08 ± 0.27 mm, respectively. The mean number of MMP-13-positive osteoclasts was highest in celecoxib-treated group followed by the control group and was decreased in the ketorolac and paracetamol groups. Comparing all groups to the control revealed significant differences (P < .05). Administration of celecoxib did not reduce bone resorption or interfere with tooth movement in rats compared to other analgesics tested (ketorolac and paracetamol).

Single-tooth replacement by osseointegrated Astra Tech dental implants: a 2-year report

DEFF Research Database (Denmark)

Karlsson, U; Gotfredsen, K; Olsson, C

1998-01-01

This study presents the outcome of single-tooth restorations supported by Astra Tech single-tooth implants followed for 2 years. Forty-seven implants were placed in the same number of patients. Forty-three patients attended the second recall visit, and none of the evaluated implants have been...

The effect of buccal corticotomy on accelerating orthodontic tooth movement of maxillary canine

Directory of Open Access Journals (Sweden)

Mohammad Reza Jahanbakhshi

2016-01-01

Conclusion: Based on result of this study, corticotomy can accelerates the rate of orthodontic tooth movement about two times faster than conventional orthodontics and it is significant in early stages after surgical porsedure. Therefore Buccal corticotomy is a useful adjunct technique for accelerating orthodontic tooth movement.

Tooth structure and fracture strength of cavities

DEFF Research Database (Denmark)

Mondelli, José; Sene, Fábio; Ramos, Renata Pereira

2007-01-01

This study evaluated, in vitro, the loss of tooth substance after cavity preparation for direct and indirect restorations and its relationship with fracture strength of the prepared teeth. Sixty sound human maxillary first premolars were assigned to 6 groups (n=10). MOD direct composite cavities......) or 1/2 (Groups III and VI) of the intercuspal distance. Teeth were weighed (digital balance accurate to 0.001 g) before and after preparation to record tooth substance mass lost during cavity preparation. The prepared teeth were submitted to occlusal loading to determine their fracture strength using...... mass loss (13.91%) than composite resin preparations with the same width (10.02%). 1/2-inlay cavities had 21.34% of mass loss versus 16.19% for the 1/2-composite resin cavities. Fracture strength means (in kgf) were: GI = 187.65; GII = 143.62; GIII = 74.10; GIV = 164.22; GV = 101.92; GVI = 50...

Coordination of Cellular Dynamics Contributes to Tooth Epithelium Deformations

Science.gov (United States)

Morita, Ritsuko; Kihira, Miho; Nakatsu, Yousuke; Nomoto, Yohei; Ogawa, Miho; Ohashi, Kazumasa; Mizuno, Kensaku; Tachikawa, Tetsuhiko; Ishimoto, Yukitaka; Morishita, Yoshihiro; Tsuji, Takashi

2016-01-01

The morphologies of ectodermal organs are shaped by appropriate combinations of several deformation modes, such as invagination and anisotropic tissue elongation. However, how multicellular dynamics are coordinated during deformation processes remains to be elucidated. Here, we developed a four-dimensional (4D) analysis system for tracking cell movement and division at a single-cell resolution in developing tooth epithelium. The expression patterns of a Fucci probe clarified the region- and stage-specific cell cycle patterns within the tooth germ, which were in good agreement with the pattern of the volume growth rate estimated from tissue-level deformation analysis. Cellular motility was higher in the regions with higher growth rates, while the mitotic orientation was significantly biased along the direction of tissue elongation in the epithelium. Further, these spatio-temporal patterns of cellular dynamics and tissue-level deformation were highly correlated with that of the activity of cofilin, which is an actin depolymerization factor, suggesting that the coordination of cellular dynamics via actin remodeling plays an important role in tooth epithelial morphogenesis. Our system enhances the understanding of how cellular behaviors are coordinated during ectodermal organogenesis, which cannot be observed from histological analyses. PMID:27588418

Estimation of Tooth Size Discrepancies among Different Malocclusion Groups.

Science.gov (United States)

Hasija, Narender; Bala, Madhu; Goyal, Virender

2014-05-01

Regards and Tribute: Late Dr Narender Hasija was a mentor and visionary in the light of knowledge and experience. We pay our regards with deepest gratitude to the departed soul to rest in peace. Bolton's ratios help in estimating overbite, overjet relationships, the effects of contemplated extractions on posterior occlusion, incisor relationships and identification of occlusal misfit produced by tooth size discrepancies. To determine any difference in tooth size discrepancy in anterior as well as overall ratio in different malocclusions and comparison with Bolton's study. After measuring the teeth on all 100 patients, Bolton's analysis was performed. Results were compared with Bolton's means and standard deviations. The results were also subjected to statistical analysis. Results show that the mean and standard deviations of ideal occlusion cases are comparable with those Bolton but, when the mean and standard deviation of malocclusion groups are compared with those of Bolton, the values of standard deviation are higher, though the mean is comparable. How to cite this article: Hasija N, Bala M, Goyal V. Estimation of Tooth Size Discrepancies among Different Malocclusion Groups. Int J Clin Pediatr Dent 2014;7(2):82-85.

Cross Sectional: bilateral parent-child interactions in school-age children's tooth-brushing behaviors.

Science.gov (United States)

Goh, Esther C L; Hsu, Stephen Chin-Ying

2013-01-01

The purpose of this study was to examine bilateral dynamics between parents and children in influencing children's tooth-brushing behaviors. In-depth conversational interviews-a specific qualitative method-were conducted with 38 parents in urban Xiamen, China and Singapore to learn insights into parental strategies for encouraging tooth-brushing habits in 6- to 9-year-old children. The interviews also examined the range of responses from children toward these parental strategies. Children usually do not comply with these tooth-brushing instructions from parents without a process of negotiation. Children's responses ranged from active resistant to compliant. Parents in Xiamen tended to use softer strategies and were more prone to be emotionally and behaviorally influenced by children's effort to thwart these strategies. Conversely, Singapore parents tended to demonstrate greater tenacity in negotiating with children. The process of developing children's tooth-brushing habits is not a unilateral from-parent-to-children process. Instead, it should be conceptualized as an ongoing interaction with bilateral power of influence from both parties.

THE EFFECTS OF PGE1 AND INDOMETHACIN ON ORTHODONTIC TOOTH MOVEMENT IN RAT

Directory of Open Access Journals (Sweden)

EA. Niaki

1999-09-01

Full Text Available  Prostaglandin £j (PGE-^ and indomethacin, a nonstroidal antiinflammatory drug, were separately administered during ortliodontic tooth movement in rats. At the beginning, an orthodontic appliance was placed and activated in male albinos rats. In tlie first examination, the experimental group received submucosal injections of PGE-y (10 mg/kg/day near the first maxillary riglit molars, and alcohol was injected to control group animals as a vehicle similarly. Jn the second examination, indomethacin (10 mg/kg/day and metiiyl cellulose subcutaneousfy injected to experimental and control groups respectively. Tooth movement was measured at 1,3,5,7,9 and 11 days. In PGE^ group, tooth movement increased significantly at the beginning of seven days as compared to the vehicle injected group and the number of osteoclast and Howship's lacunae were markedly increased. A significant iniiibition of tooth movement occurred beginning at seven days in the indomethacin group compared to the control group.

Prenatal ultrasound and postmortem histologic evaluation of tooth germs: an observational, transversal study.

Science.gov (United States)

Seabra, Mariana; Felino, António; Nogueira, Rosete; Valente, Francisco; Braga, Ana Cristina; Vaz, Paula

2015-05-12

Hypodontia is the most frequent developmental anomaly of the orofacial complex, and its detection in prenatal ultrasound may indicate the presence of congenital malformations, genetic syndromes and chromosomal abnormalities. To date, only a few studies have evaluated the histological relationship of human tooth germs identified by two-dimensional (2D) ultrasonography. In order to analyze whether two-dimensional ultrasonography of tooth germs may be successfully used for identifying genetic syndromes, prenatal ultrasound images of fetal tooth germs obtained from a Portuguese population sample were compared with histological images obtained from fetal autopsies. Observational, descriptive, transversal study. The study protocol followed the ethical principles outlined by the Helsinki Declaration and was approved by the Ethics Committee of the School of Dental Medicine, University of Porto (FMDUP, Porto, Portugal) and of the Centro Hospitalar de Vila Nova de Gaia/Espinho (CHVNG/EPE, Porto, Portugal) as well as by the CGC Genetics Embryofetal Pathology Laboratory. Eighty-five fetuses examined by prenatal ultrasound screening from May 2011 to August 2012 had an indication for autopsy following spontaneous fetal death or medical termination of pregnancy. Of the 85 fetuses, 37 (43.5%) were randomly selected for tooth germ evaluation by routine histopathological analysis. Fetuses who were up to 30 weeks of gestation, and whose histological pieces were not representative of all maxillary tooth germs was excluded. Twenty four fetus between the 13(th) and 30(th) weeks of gestation fulfilled the parameters to autopsy. Twenty four fetuses were submitted to histological evaluation and were determined the exact number, morphology, and mineralization of their tooth germs. All tooth germs were identifiable with ultrasonography as early as the 13(th) week of gestation. Of the fetuses autopsied, 41.7% had hypodontia (29.1% maxillary hypodontia and 20.9% mandibular hypodontia). This

Mesenchymal stem cell-mediated functional tooth regeneration in swine.

Directory of Open Access Journals (Sweden)

Wataru Sonoyama

2006-12-01

Full Text Available Mesenchymal stem cell-mediated tissue regeneration is a promising approach for regenerative medicine for a wide range of applications. Here we report a new population of stem cells isolated from the root apical papilla of human teeth (SCAP, stem cells from apical papilla. Using a minipig model, we transplanted both human SCAP and periodontal ligament stem cells (PDLSCs to generate a root/periodontal complex capable of supporting a porcelain crown, resulting in normal tooth function. This work integrates a stem cell-mediated tissue regeneration strategy, engineered materials for structure, and current dental crown technologies. This hybridized tissue engineering approach led to recovery of tooth strength and appearance.

Caspase-7 in molar tooth development

Czech Academy of Sciences Publication Activity Database

Matalová, Eva; Vanden Berghe, T.; Švandová, Eva; Vandenabeele, P.; Healy, C.; Sharpe, P. T.; Tucker, A. S.

2012-01-01

Roč. 57, č. 11 (2012), s. 1474-1481 ISSN 0003-9969 R&D Projects: GA AV ČR IAA600450904 Grant - others:GA ČR(CZ) GAP502/12/1285 Program:GA Institutional research plan: CEZ:AV0Z50450515 Keywords : tooth * apoptosis * mineralisation Subject RIV: FF - HEENT, Dentistry Impact factor: 1.549, year: 2012

Immunohistochemical Examination for the Distribution of Podoplanin-Expressing Cells in Developing Mouse Molar Tooth Germs

Science.gov (United States)

Imaizumi, Yuri; Amano, Ikuko; Tsuruga, Eichi; Kojima, Hiroshi; Sawa, Yoshihiko

2010-01-01

We recently reported the expression of podoplanin in the apical bud of adult mouse incisal tooth. This study was aimed to investigate the distribution of podoplanin-expressing cells in mouse tooth germs at several developing stages. At the bud stage podoplanin was expressed in oral mucous epithelia and in a tooth bud. At the cap stage podoplanin was expressed on inner and outer enamel epithelia but not in mesenchymal cells expressing the neural crest stem cell marker nestin. At the early bell stage nestin and podoplanin were expressed in cervical loop and odontoblasts. At the root formation stage both nestin and podoplanin were weakly expressed in odontoblasts generating radicular dentin. Podoplanin expression was also found in the Hertwig epithelial sheath. These results suggest that epithelial cells of developing tooth germ acquire the ability to express nestin, and that tooth germ epithelial cells maintain the ability to express podoplanin in oral mucous epithelia. The expression of podoplanin in odontoblasts was induced as tooth germ development advanced, but was suppressed with the completion of the primary dentin, suggesting that podoplanin may be involved in the cell growth of odontoblasts. Nestin may function as an intermediate filament that binds podoplanin in odontoblasts. PMID:21060740

Ten-Year Follow-Up of a Fragment Reattachment to an Anterior Tooth: A Conservative Approach.

Science.gov (United States)

Mendes, Luiz; Laxe, Laisa; Passos, Leandro

2017-01-01

This report describes the 10-year follow-up data of a patient who underwent fragment reattachment to the maxillary central incisor after coronal fracture with pulp exposure as well as the procedures followed for functional and esthetic adjustments. A 9-year-old female patient presented at the clinic of dentistry at the State University of Rio de Janeiro with a coronal fracture and pulp exposure of the right maxillary central incisor that had occurred immediately after an accident. The intact tooth fragment was recovered at the accident site and stored in milk. The treatment plan followed was to perform direct pulp capping and tooth fragment reattachment. When the patient was 14 years old, adhesion between fragment and remaining tooth was lost, and fragment reattachment was performed. Five years later, the same tooth presented clinical discoloration and absence of sensitivity during pulp vitality tests. Subsequently, a new treatment plan was formulated, which included endodontic treatment, followed by nonvital tooth bleaching and light-cured composite resin restoration. An esthetic and natural-looking restoration was achieved. Tooth fragment reattachment is not a temporary restorative technique and requires functional and esthetic adjustments over time to maintain the biomimetic characteristics of traumatized anterior teeth and predictable outcomes.

Tooth loss and oral health-related quality of life: a systematic review and meta-analysis

LENUS (Irish Health Repository)

Gerritsen, Anneloes E

2010-11-05

Abstract Background It is increasingly recognized that the impact of disease on quality of life should be taken into account when assessing health status. It is likely that tooth loss, in most cases being a consequence of oral diseases, affects Oral Health-Related Quality of Life (OHRQoL). The aim of the present study is to systematically review the literature and to analyse the relationship between the number and location of missing teeth and oral health-related quality of life (OHRQoL). It was hypothesized that tooth loss is associated with an impairment of OHRQoL. Secondly, it was hypothesized that location and distribution of remaining teeth play an important role in this. Methods Relevant databases were searched for papers in English, published from 1990 to July 2009 following a broad search strategy. Relevant papers were selected by two independent readers using predefined exclusion criteria, firstly on the basis of abstracts, secondly by assessing full-text papers. Selected studies were grouped on the basis of OHRQoL instruments used and assessed for feasibility for quantitative synthesis. Comparable outcomes were subjected to meta-analysis; remaining outcomes were subjected to a qualitative synthesis only. Results From a total of 924 references, 35 were eligible for synthesis (inter-reader agreement abstracts κ = 0.84 ± 0.03; full-texts: κ = 0.68 ± 0.06). Meta-analysis was feasible for 10 studies reporting on 13 different samples, resulting in 6 separate analyses. All studies showed that tooth loss is associated with unfavourable OHRQoL scores, independent of study location and OHRQoL instrument used. Qualitative synthesis showed that all 9 studies investigating a possible relationship between number of occluding pairs of teeth present and OHRQoL reported significant positive correlations. Five studies presented separate data regarding OHRQoL and location of tooth loss (anterior tooth loss vs. posterior tooth loss). Four of these reported highest impact

Caffeine may enhance orthodontic tooth movement through increasing osteoclastogenesis induced by periodontal ligament cells under compression.

Science.gov (United States)

Yi, Jianru; Yan, Boxi; Li, Meile; Wang, Yu; Zheng, Wei; Li, Yu; Zhao, Zhihe

2016-04-01

Caffeine is the kernel component of coffee and has multiple effects on bone metabolism. Here we aimed to investigate the effects of caffeine intake on orthodontic tooth movement (OTM). (1) In the in vivo study, two groups comprising 15 randomly assigned rats each underwent orthodontic treatment. One group ingested caffeine at 25mg/kg body weight per day and the other, plain water. After 3 weeks, the degree of tooth movement and effect on the periodontium were assessed. (2) In the in vitro study, we established a model mimicking the essential bioprocess of OTM, which contained a periodontal ligament tissue model (PDLtm), and a co-culture system of osteoblasts (OBs) and osteoclast precursors (pre-OCs). After being subjected to static compressive force with or without caffeine administration, the conditioned media from the PDLtm were used for the OB/pre-OC co-cultures to induce osteoclastogenesis. (1) In vivo, the caffeine group displayed a significantly greater rate of tooth movement than the control. The alveolar bone mineral density and bone volume fraction were similar between the two groups; however, immunohistochemical staining showed that the caffeine group had significantly more TRAP(+) osteoclasts and higher RANKL expression in the compressed periodontium. (2) In vitro, caffeine at 0.01mM significantly enhanced the compression-induced expression of RANKL and COX-2, as well as prostaglandin E2 production in the PDLtm. Furthermore, the "caffeine+compression"-conditioned media induced significantly more TRAP(+) OC formation when compared with compression alone. Daily intake of caffeine, at least at some specific dosage, may enhance OTM through increasing osteoclastogenesis. Copyright © 2016 Elsevier Ltd. All rights reserved.

Measurement of gross alpha and gross beta activity concentrations in human tooth

International Nuclear Information System (INIS)

Soeguet, Omer; Aydin, Mehmet Fatih; Kuecuekoender, Erdal; Zorer, Ozlem Selcuk; Dogru, Mahmut

2010-01-01

The gross alpha and gross beta activity concentrations were measured in human tooth taken from 3 to 6 age-groups to 40 and over ones. Accumulated teeth samples are investigated in two groups as under and above 18 years. The gross alpha and beta radioactivity of human tooth samples was measured by using a gas-flow proportional counter (PIC-MPC 9604-α/β counter). In tooth samples, for female age-groups, the obtained results show that the mean gross alpha and gross beta activity concentrations varied between 0.534-0.203 and 0.010-0.453 Bq g -1 and the same concentrations for male age-groups varied between 0.009-1.168 and 0.071-0.204 Bq g -1 , respectively.

Osteoblast and osteoclast behaviors in the turnover of attachment bones during medaka tooth replacement.

Science.gov (United States)

Mantoku, Akiko; Chatani, Masahiro; Aono, Kazushi; Inohaya, Keiji; Kudo, Akira

2016-01-15

Tooth replacement in polyphyodont is a well-organized system for maintenance of homeostasis of teeth, containing the dynamic structural change in skeletal tissues such as the attachment bone, which is the supporting element of teeth. Histological analyses have revealed the character of tooth replacement, however, the cellular mechanism of how skeletal tissues are modified during tooth replacement is largely unknown. Here, we showed the important role of osteoblasts for controlling osteoclasts to modify the attachment bone during tooth replacement in medaka pharyngeal teeth, coupled with an osterix-DsRed/TRAP-GFP transgenic line to visualize osteoblasts and osteoclasts. In the turnover of the row of attachment bones, these bones were resorbed at the posterior side where most developed functional teeth were located, and generated at the anterior side where teeth were newly erupted, which caused continuous tooth replacement. In the cellular analysis, osteoclasts and osteoblasts were located at attachment bones separately, since mature osteoclasts were localized at the resorbing side and osteoblasts gathered at the generating side. To demonstrate the role of osteoclasts in tooth replacement, we established medaka made deficient in c-fms-a by TALEN. c-fms-a deficient medaka showed hyperplasia of attachment bones along with reduced bone resorption accompanied by a low number of TRAP-positive osteoclasts, indicating an important role of osteoclasts in the turnover of attachment bones. Furthermore, nitroreductase-mediated osteoblast-specific ablation induced disappearance of osteoclasts, indicating that osteoblasts were essential for maintenance of osteoclasts for the proper turnover. Taken together, our results suggested that the medaka attachment bone provides the model to understand the cellular mechanism for tooth replacement, and that osteoblasts act in the coordination of bone morphology by supporting osteoclasts. Copyright © 2015 Elsevier Inc. All rights reserved.

Does common prescription medication affect the rate of orthodontic tooth movement? A systematic review.

Science.gov (United States)

Makrygiannakis, Militiadis A; Kaklamanos, Eleftherios G; Athanasiou, Athanasios E

2018-03-06

As the taking of any medication may theoretically affect the complex pathways responsible for periodontal tissue homeostasis and the events leading to orthodontic tooth movement, it is considered important for the orthodontist to be able to identify prospective patients' history and patterns of pharmaceutical consumption. To systematically investigate and appraise the quality of the available evidence regarding the effect of commonly prescribed medications on the rate of orthodontic tooth movement. Search without restrictions in eight databases and hand searching until June 2017. Controlled studies investigating the effect of commonly prescribed medications with emphasis on the rate of orthodontic tooth movement. Following study retrieval and selection, relevant data was extracted and the risk of bias was assessed using the SYRCLE's Risk of Bias Tool. Twenty-seven animal studies, involving various pharmacologic and orthodontic interventions, were finally identified. Most studies were assessed to be at unclear or high risk of bias. The rate of orthodontic tooth movement was shown to increase after the administration of diazepam, Vitamin C and pantoprazole, while simvastatin, atorvastatin, calcium compounds, strontium ranelate, propranolol, losartan, famotidine, cetirizine, and metformin decreased the rate of orthodontic tooth movement. No interference with the rate of orthodontic tooth movement was reported for phenytoin, phenobarbital and zinc compounds, whereas, inconsistent or conflicting effects were noted after the administration of L-thyroxine, lithium compounds, fluoxetine and insulin. The quality of the available evidence was considered at best as low. Commonly prescribed medications may exhibit variable effects on the rate of orthodontic tooth movement. Although the quality of evidence was considered at best as low, raising reservations about the strength of the relevant recommendations, the clinician should be capable of identifying patients taking

Effects of IL6 C-634G polymorphism on tooth loss and their interaction with smoking habits.

Science.gov (United States)

Suma, S; Naito, M; Wakai, K; Sasakabe, T; Hattori, Y; Okada, R; Kawai, S; Hishida, A; Morita, E; Nakagawa, H; Tamura, T; Hamajima, N

2015-09-01

To examine the association between an IL6 (Interleukin-6) polymorphism (C-634G or rs1800796) and tooth loss, and an interaction between the polymorphism and smoking habits for the loss. Our subjects were 4917 check-up examinees ages 35-69. They reported tooth loss and lifestyle in a questionnaire. We regressed the number of teeth on the IL6 genotype, gender, age, smoking, drinking, diabetes, hypertension, physical activity, energy intake, education, and brushing. We further estimated multivariate-adjusted odds ratios (ORs) for having smoking and tooth loss was stronger among those with GG than among those with CC. In a multiple regression analysis, a significant interaction was found between GG genotype and current smoking in the prediction of tooth loss (P = 0.018). The IL6 C-634G polymorphism was significantly associated with tooth loss. Our results suggest greater effects of smoking on tooth loss in GG genotype individuals. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Patient Discomfort Following Single-Tooth Implant Placement

DEFF Research Database (Denmark)

Spin-Neto, Rubens; Pontes, Ana Emília Farias; Wenzel, Ann

2014-01-01

scores for pain and swelling decreased continuously over the time period in both groups. Conclusions: The longer treatment time in IR didn't increase patients' perception of pain, bleeding and swelling, compared to CR. The impact of immediate tooth restoration on patients' esthetic outcome should...

Restoration of noncarious tooth defects by dentists in The Dental Practice-Based Research Network

DEFF Research Database (Denmark)

Nascimento, Marcelle M; Gordan, Valeria V; Qvist, Vibeke

2011-01-01

The authors conducted a study to quantify the reasons for restoring noncarious tooth defects (NCTDs) by dentists in The Dental Practice-Based Research Network (DPBRN) and to assess the tooth, patient and dentist characteristics associated with those reasons....

Esterase variation in Turkish white-toothed shrews (Crocidura: Record of a trimeric esterase

Directory of Open Access Journals (Sweden)

Tez C.

2009-01-01

Full Text Available This study focuses on esterase variation of the genus Crocidura in Turkey. A total of 248 white-toothed shrews were analyzed by means of cellulose acetate gel electrophoresis. Liver tissue and alfa naphthyl acetate were used to investigate esterase variation in Turkish white-toothed shrews. A different esterase banding pattern was found in one Crocidura individual. This phenotype had four anodally migrated bands on cellulose acetate gel. The Crocidura individual displaying the given phenotype was identified as Crocidura suaveolens. The different esterase banding pattern observed in this study is considered to be a result of the trimeric structure of esterase in the lesser white-toothed shrew (Crocidura suaveolens.

Tooth brushing among 11- to 15-year-olds in Denmark: combined effect of social class and migration status.

Science.gov (United States)

Bast, L S; Nordahl, H; Christensen, L B; Holstein, B E

2015-03-01

Regular tooth brushing in adolescence predicts stable tooth brushing habits later in life. Differences in tooth brushing habits by ethnic background and socioeconomic position have been suggested. We investigated migration status and social class in relation to infrequent tooth brushing both separately and combined. The study population was 11-15 year-olds chosen from a clustered random sample of schools. Univariate and multivariate logistic regression analyses estimated the separate and combined effects of migration status and social class on less than twice daily tooth brushing. 10,607 respondents: a response rate of 88.3%. Boys of lower social class had higher odds ratio (OR) of infrequent tooth brushing than girls: 1.98 (95% confidence interval 1.62-2.41) vs 1.80 (1.53-2.24). Immigrants and descendants had higher odds compared to adolescents of Danish origin: immigrant boys OR 1.39 (1.05-1.89), girls OR 1.92 (1.47-2.50); descendant boys OR 2.53 (1.97-3.27), girls OR 2.56 (2.02-3.35). Analyses of the combined effect of social class and migration status showed that the social gradient in tooth brushing habits observed among ethnic Danes cannot be found among groups of immigrants and descendants. The study shows that both non-Danish origin and low social class increases the risk of infrequent tooth brushing among school-aged children. The study calls for in depth analyses of the processes which influence young people's tooth brushing habits. Further, there is a need to strengthen the promotion of appropriate tooth brushing habits of minority and low social class youths.

EPR and TL-based beta dosimetry measurements in various tooth components contaminated by 90Sr

International Nuclear Information System (INIS)

Veronese, I.; Fattibene, P.; Cantone, M.C.; De Coste, V.; Giussani, A.; Onori, S.; Shishkina, E.A.

2008-01-01

Thermoluminescence-based beta dosimetry, previously proposed for the estimate of the internal contamination in teeth, and EPR has been used in this paper to investigate the homogeneity of 90 Sr contamination and of dose within nine teeth of one person born in the year of the onset of waterborne radioactive releases of the Mayak plutonium facility. A large deviation of dose and activity distributions in both enamel and radical dentine of the various teeth was observed. Average dose was 27±7Gy in enamel and 0.90±0.31Gy in radical dentine. Average 90 Sr concentration was 52±8Bq/g in enamel and 5±2Bq/g in radical dentine. The observed deviation around the mean value of dose and 90 Sr concentration can be explained due to the specific mineral evolution of each tooth at the time of Sr intake. In the same donor, a negative correlation was also observed between radical dentine and enamel for the 90 Sr specific activity as well for the dose. Similar analyses performed on one massive molar belonging to a second donor revealed absence of correlation between dose and 90 Sr concentration in the same tissue, indicating a dose contribution from 90 Sr present in neighbouring tissue compartments. Systematic differences in cumulated dose and activity levels between the lingual and the buccal parts of crown dentine and of enamel were also observed

Study on tooth development, past, present, and future.

Science.gov (United States)

Jung, Han-Sung; Hitoshi, Yamamoto; Kim, Hee-Jin

2003-04-01

For decades, the understanding of craniofacial development has been a central issue in odontology and developmental biology. As a consequence, a significant number of deformities are being studied for their variety of genotype and phenotype. Although there is little doubt about the essential roles of homeobox genes, transcription factors, and growth factors, we now know at least the fundamental strategy of craniofacial biology. The tooth as an organ performs a whole range of functions, each of which is truly indispensable for the maintenance of life. The possession of teeth is, therefore, obviously coupled with the complication of the natural structure of an individual organism. In the following, we shall focus on a brief history of tooth studies and some suggestions for obtaining a full understanding of teeth in the future. Copyright 2003 Wiley-Liss, Inc.

Computerized Modeling and Loaded Tooth Contact Analysis of Hypoid Gears Manufactured by Face Hobbing Process

Science.gov (United States)

Nishino, Takayuki

The face hobbing process has been widely applied in automotive industry. But so far few analytical tools have been developed. This makes it difficult for us to optimize gear design. To settle this situation, this study aims at developing a computerized tool to predict the running performances such as loaded tooth contact pattern, static transmission error and so on. First, based upon kinematical analysis of a cutting machine, a mathematical description of tooth surface generation is given. Second, based upon the theory of gearing and differential geometry, conjugate tooth surfaces are studied. Then contact lines are generated. Third, load distribution along contact lines is formulated. Last, the numerical model is validated by measuring loaded transmission error and loaded tooth contact pattern.

Imaging tooth enamel using zero echo time (ZTE) magnetic resonance imaging

Science.gov (United States)

Rychert, Kevin M.; Zhu, Gang; Kmiec, Maciej M.; Nemani, Venkata K.; Williams, Benjamin B.; Flood, Ann B.; Swartz, Harold M.; Gimi, Barjor

2015-03-01

In an event where many thousands of people may have been exposed to levels of radiation that are sufficient to cause the acute radiation syndrome, we need technology that can estimate the absorbed dose on an individual basis for triage and meaningful medical decision making. Such dose estimates may be achieved using in vivo electron paramagnetic resonance (EPR) tooth biodosimetry, which measures the number of persistent free radicals that are generated in tooth enamel following irradiation. However, the accuracy of dose estimates may be impacted by individual variations in teeth, especially the amount and distribution of enamel in the inhomogeneous sensitive volume of the resonator used to detect the radicals. In order to study the relationship between interpersonal variations in enamel and EPR-based dose estimates, it is desirable to estimate these parameters nondestructively and without adding radiation to the teeth. Magnetic Resonance Imaging (MRI) is capable of acquiring structural and biochemical information without imparting additional radiation, which may be beneficial for many EPR dosimetry studies. However, the extremely short T2 relaxation time in tooth structures precludes tooth imaging using conventional MRI methods. Therefore, we used zero echo time (ZTE) MRI to image teeth ex vivo to assess enamel volumes and spatial distributions. Using these data in combination with the data on the distribution of the transverse radio frequency magnetic field from electromagnetic simulations, we then can identify possible sources of variations in radiation-induced signals detectable by EPR. Unlike conventional MRI, ZTE applies spatial encoding gradients during the RF excitation pulse, thereby facilitating signal acquisition almost immediately after excitation, minimizing signal loss from short T2 relaxation times. ZTE successfully provided volumetric measures of tooth enamel that may be related to variations that impact EPR dosimetry and facilitate the development

Acid and Alkaline Phosphatase Levels in GCF during Orthodontic Tooth Movement

Science.gov (United States)

Farahani, Mohammad; Safavi, Seyed Mohammadreza; Dianat, Omid; Khoramian Tusi, Somayeh; Younessian, Farnaz

2015-01-01

Statement of the Problem The present constituents of gingival crevicular fluid (GCF) can reflect the changes occurring in underlying tissues. Considering variety of biologic bone markers, alkaline phosphatase and acid phosphatase have been examined as bone turn over markers in orthodontic tooth movement. Purpose The current study designed in a longitudinal pattern to determine the changes of acid and alkaline phosphatase (ACP & ALP) in GCF during orthodontic tooth movement. Materials and Method An upper canines from twelve patients (mean age: 14±2 years) undergoing extraction orthodontic treatment for distal movement served as the test tooth (DC), and its contralateral (CC) and antagonist (AC) canines were used as controls. The CC was included in orthodontic appliance without orthodontic force; the AC was free from any orthodontic appliance. The GCF around the experimental teeth was harvested from mesial and distal tooth sites immediately before appliance placement (T0), and 14 (T2) and 28 days (T3) after it and ALP and ACP concentration were determined spectrophotometrically. Results ALP concentration was elevated significantly in DC and CC groups at days 14 and 28 compared with the AC. In DC group, the ALP was significantly greater in mesial sites than distal site, while no significant changes were found between both sites of CC. The peak level of ALP was observed in mesial sites of DC at T2. Regarding ACP, significant elevation of this enzyme was seen in DC group both in mesial and distal sites at T2 and T3. The peak level of this enzyme was seen at T2. Conclusion Monitoring simultaneous changes of ALP and ACP levels in GCF can reflect the tissue responses occur in periodontium during bone formation and bone resorption during orthodontic tooth movement, respectively. PMID:26535403

Relationship between tooth value and skin color in patients visiting Royal Medical Services clinics of Jordan.

Science.gov (United States)

Al-Nsour, Hind Fahed; Al-Zoubi, Tamara Trad; Al-Rimawi, Ali Salaheddin

2018-03-01

Facial and dental aesthetics are becoming of great concern for patients, especially for the younger generation. Tooth color matching and selection is considered a vital element in order to create an attractive beautiful smile. The importance of tooth color matching is to adjust tooth colors to obtain a good match with adjacent teeth and the skin. This is considered a challenge especially if adjacent teeth were lost or records of patients' teeth color were not available. The aim of this study was to determine the relationship between skin complexion and tooth value in a Jordanian population. A cross-sectional study of 520 individuals who were randomly selected and belonging to different age groups, ranging from 15-65 years, with equal sex distribution. These patients visited the dental clinics at different Jordanian military hospitals. The study was carried out over a period of one year from 2015 to 2016. The randomly selected sample was examined by one researcher. Shade of the middle third of the labial surface of central incisor was determined visually using VITA tooth guide, 3D-MASTER shade guide. Tooth shades were divided into two categories according to their value. The skin complexion was identified using Fitzpatrick skin type test, and was categorized into two categories (fair and dark). Data were statistically analyzed using Epi Info version 6. A statistically significant tooth shade value difference was discovered among subjects of different skin color (pvalue among a Jordanian population. Thus, considering the skin complexion when choosing tooth shades is helpful in achieving a pleasing good-looking smile, yet further investigations in this field must be carried out.

Cigarette smoking, tooth brushing characteristics, and perceived ...

African Journals Online (AJOL)

This study was conducted among four hundred non-dental undergraduates of University of Benin, Benin City, Nigeria to assess the prevalence of cigarette smoking, tooth brushing characteristics, perceived efficacy in oral self-care and preventing gingivodental diseases among them. The result showed that the perceived ...

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... June 1, 2018 About | Contact InfoBites Quick Reference Learn more Nutrition - Adults When Should My Child First See a Dentist? Check Menstrual Calendar for Tooth Extraction Temporomandibular Joint Disorder Men: Looking for a Better Job? Start by Visiting the Dentist Are You ...

Death in the life of a tooth

Czech Academy of Sciences Publication Activity Database

Matalová, Eva; Tucker, A. S.; Sharpe, P. T.

2004-01-01

Roč. 83, č. 1 (2004), s. 11-16 ISSN 0022-0345 R&D Projects: GA ČR GP204/02/P112 Institutional research plan: CEZ:AV0Z5045916 Keywords : apoptosis * tooth development Subject RIV: EA - Cell Biology Impact factor: 3.131, year: 2004

Tooth wear in three ethnic groups in Sabah (northern Borneo).

Science.gov (United States)

Milosevic, A; Lo, M S

1996-12-01

The prevalence and associated aetiologies of tooth wear were investigated in three ethnic groups in Sabah (Northern Borneo) using the Tooth Wear Index (TWI). The number of surfaces with enamel wear only, dentine exposed for less than a third or dentine exposed for more than a third were categorised into the TW minimal, moderate or severe respectively. A structured questionnaire was used to elicit medical/dental history, oral hygiene practices, satisfaction with body image, diet and other personal habits/details. The sample comprised of a self selected sample of 148 dental hospital attenders; 47 (32 per cent) each of ethnic Chinese and Malay and 54 (36 per cent) of ethnic Kadazan, matched for age and with a similar number of scoreable teeth per subject. Dentine exposure within the total sample was a common finding (95 per cent TW with moderate, 41 per cent TW severe). The Kadazan group had significantly (P Chinese or Malay. Tobacco chewing was positively associated (rho = +0.4, P Chinese subjects. The aetiological factors associated with this tooth wear are different to those encountered in Western cultures.

PHOTOGRAMMETRY-BASED AUTOMATED MEASUREMENTS FOR TOOTH SHAPE AND OCCLUSION ANALYSIS

Directory of Open Access Journals (Sweden)

V. A. Knyaz

2016-06-01

Full Text Available Tooth measurements (odontometry are performed for various scientific and practical applications, including dentistry. Present-day techniques are being increasingly based on 3D model use that provides wider prospects in comparison to measurements on real objects: teeth or their plaster copies. The main advantages emerge through application of new measurement methods which provide the needed degree of non-invasiveness, precision, convenience and details. Tooth measurements have been always regarded as a time-consuming research, even more so with use of new methods due to their wider opportunities. This is where automation becomes essential for further development and implication of measurement techniques. In our research automation in obtaining 3D models and automation of measurements provided essential data that was analysed to suggest recommendations for tooth preparation – one of the most responsible clinical procedures in prosthetic dentistry – within a comparatively short period of time. The original photogrammetric 3D reconstruction system allows to generate 3D models of dental arches, reproduce their closure, or occlusion, and to perform a set of standard measurement in automated mode.

Photogrammetry-Based Automated Measurements for Tooth Shape and Occlusion Analysis

Science.gov (United States)

Knyaz, V. A.; Gaboutchian, A. V.

2016-06-01

Tooth measurements (odontometry) are performed for various scientific and practical applications, including dentistry. Present-day techniques are being increasingly based on 3D model use that provides wider prospects in comparison to measurements on real objects: teeth or their plaster copies. The main advantages emerge through application of new measurement methods which provide the needed degree of non-invasiveness, precision, convenience and details. Tooth measurements have been always regarded as a time-consuming research, even more so with use of new methods due to their wider opportunities. This is where automation becomes essential for further development and implication of measurement techniques. In our research automation in obtaining 3D models and automation of measurements provided essential data that was analysed to suggest recommendations for tooth preparation - one of the most responsible clinical procedures in prosthetic dentistry - within a comparatively short period of time. The original photogrammetric 3D reconstruction system allows to generate 3D models of dental arches, reproduce their closure, or occlusion, and to perform a set of standard measurement in automated mode.

Effect of thermal stresses on the mechanism of tooth pain.

Science.gov (United States)

Oskui, Iman Z; Ashtiani, Mohammed N; Hashemi, Ata; Jafarzadeh, Hamid

2014-11-01

Daily hot and cold thermal loadings on teeth may result in structural deformation, mechanical stress, and pain signaling. The aim of this study was to compare the adverse effects of hot and cold beverages on an intact tooth and, then, to provide physical evidence to support the hydrodynamic theory of tooth pain sensation mechanism. Three-dimensional finite element analysis was performed on a premolar model subjected to hot and cold thermal loadings. Elapsed times for heat diffusion and stress detection at the pulp-dentin junction were calculated as measures of the pain sensation. Extreme tensile stress within the enamel resulted in damage in cold loadings. Also, extreme values of stress at the pulpal wall occurred 21.6 seconds earlier than extreme temperatures in hot and cold loadings. The intact tooth was remarkably vulnerable to cold loading. Earlier changes in mechanical stress rather than temperature at the pulp-dentin junction indicate that the dental pain caused by hot or cold beverages may be based on the hydrodynamic theory. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Restorative Management of Severe Localized Tooth Wear Using a Supraoccluding Appliance: A 5-Year Follow-Up

Directory of Open Access Journals (Sweden)

Tsz Leung Wong

2018-01-01

Full Text Available This case report illustrates a novel conservative restorative management of a patient with bulimia nervosa who presented with severe localized upper palatal tooth wear and an anterior reverse overjet. This was achieved by using a localized bite raising or supraoccluding appliance, cemented on the lingual side of the lower anterior teeth to create interocclusal space, obviating the need for tooth reduction of the eroded upper palatal and incisal tooth surfaces. Surgical crown lengthening was performed to create a better aesthetic gingival architecture. All-ceramic restorations were provided on the upper anterior teeth to restore the tooth surface loss and provide a positive overbite and overjet. There was no complication or other observable biological change detected at the 5-year follow-up. The use of an appliance applying the supraoccluding technique, or Dahl concept, is a safe, conservative, and useful treatment option in the management of localized tooth wear.

Labiogingival groove: A rare developmental tooth anomaly

Directory of Open Access Journals (Sweden)

Shiva Chauhan

2017-01-01

Full Text Available Labiogingival groove is a congenital morphologic dental anomaly, in which an infolding of the inner enamel epithelium and Hertwig's epithelial root sheath create a groove extending varying depth into root. Epithelial attachment can be breached by gingival irritation secondary to plaque accumulation creating a periodontal defect that spreads to the pulp causing primary periodontal/secondary endodontic. A 12-year-old boy reported with the complaint of painful tooth with pus discharge from labial gingival surface in the maxillary right lateral incisor for 4 months. Intraoral examination revealed bluish red gingiva with loss of contour in relation to maxillary right lateral incisor and purulent discharge in relation to it. A provisional diagnosis of localized gingival abscess in relation to maxillary right incisor (primary periodontic and secondary endodontic involvement was given, and required treatment was carried out. On exposure of the involved tooth, a labiogingival groove was noticed which could have been a contributing factor for the progression of the condition.

Evaluation of Amoxicillin & Cephalexin concentrations in dental alveolar sockets after tooth extraction

OpenAIRE

Fakhraei AH.; Jabal Ameli F.; Ghobadi G

2005-01-01

Statement of Problem: One of the most important complications after tooth extraction and oral and maxillofacial surgery is transient bacteraemia and prescription of prophylactic antibiotic is necessary to prevent postoperative infections in immunocompromised patients. Purpose: The aim of this study was the evaluation of cephalexin and amoxicillin concentrations in dental alveolar sockets following tooth extraction. Materials and Methods: In this interventional study, 80 healthy patients subje...

Orthodontic treatment of the patients having germinated tooth in the incisor region of maxilla : 2 cases report

OpenAIRE

佐藤, 和朗; 小田島, 晶子; 三條, 晃; 桑島, 幸紀; 山田, 裕之; 三浦, 廣行; サトウ, カズロウ; オダシマ, アキコ; サンジョウ, アキラ; クワジマ, ユキノリ; ヤマダ, ヒロユキ; ミウラ, ヒロユキ; Kazuro, SATOH; Akiko, ODASHIMA; Akira, SANJO

2010-01-01

We treated the malocclusion of two boys having a germinated tooth in the incisor region of maxilla. In case 1, the germinated tooth was located at the right lateral incisor, in case 2, at the left central incisor region of maxilla. The X-ray and CT examinations revealed that the germinated tooth was united by enamel and dentin and the dental pulp cavity was joined in both cases. So we carried out treatments to avoid pulpectomy in both cases; the germinated tooth aligned in the upper dental ar...

EMMPRIN (basigin/CD147) is involved in the morphogenesis of tooth germ in mouse molars.

Science.gov (United States)

Xie, Ming; Jiao, Ting; Chen, Yuqin; Xu, Chun; Li, Jing; Jiang, Xinquan; Zhang, Fuqiang

2010-05-01

The pattern of gene expression for extracellular matrix metalloproteinase inducer (EMMPRIN) was revealed in the tooth germ of mouse mandibular molars using quantitative real-time PCR. In situ hybridization and immunohistochemical study demonstrated the characteristic distribution of EMMPRIN in the different stages of tooth germ development. To investigate the functional role played by EMMPRIN in tooth germ development, EMMPRIN siRNA interference approach was carried out in cultured mouse mandibles at embryonic day 11.0 (E11.0). The results showed that EMMPRIN siRNA-treated explants exhibited a marked growth inhibition of tooth germ compared to the control and scrambled siRNA-treated explants. Meanwhile, a significant increase in MT1-MMP mRNA expression and a reduction in MMP-2, MMP-3, MMP-9, MMP-13 and MT2-MMP mRNA expression were observed in the mouse mandibles following EMMPRIN abrogation. The current results indicate that EMMPRIN could thus be involved in the early stage of tooth germ development and morphogenesis, possibly by regulating the expression of MMP genes.

Vital Signs: Dental Sealant Use and Untreated Tooth Decay Among U.S. School-Aged Children.

Science.gov (United States)

Griffin, Susan O; Wei, Liang; Gooch, Barbara F; Weno, Katherine; Espinoza, Lorena

2016-10-21

Tooth decay is one of the greatest unmet treatment needs among children. Pain and suffering associated with untreated dental disease can lead to problems with eating, speaking, and learning. School-based dental sealant programs (SBSP) deliver a highly effective intervention to prevent tooth decay in children who might not receive regular dental care. SBSPs benefits exceed their costs when they target children at high risk for tooth decay. CDC used data from the National Health and Nutrition Examination Survey (NHANES) 2011-2014 to estimate current prevalences of sealant use and untreated tooth decay among low-income (≤185% of federal poverty level) and higher-income children aged 6-11 years and compared these estimates with 1999-2004 NHANES data. The mean number of decayed and filled first molars (DFFM) was estimated for children with and without sealants. Averted tooth decay resulting from increasing sealant use prevalence was also estimated. All reported differences are significant at pdental sealant use has increased; however, most children have not received sealants. Increasing sealant use prevalence could substantially reduce untreated decay, associated problems, and dental treatment costs.

Regulation and Measurement of the Heat Generated by Automatic Tooth Preparation in a Confined Space.

Science.gov (United States)

Yuan, Fusong; Zheng, Jianqiao; Sun, Yuchun; Wang, Yong; Lyu, Peijun

2017-06-01

The aim of this study was to assess and regulate heat generation in the dental pulp cavity and circumambient temperature around a tooth during laser ablation with a femtosecond laser in a confined space. The automatic tooth preparing technique is one of the traditional oral clinical technology innovations. In this technique, a robot controlled an ultrashort pulse laser to automatically complete the three-dimensional teeth preparing in a confined space. The temperature control is the main measure for protecting the tooth nerve. Ten tooth specimens were irradiated with a femtosecond laser controlled by a robot in a confined space to generate 10 teeth preparation. During the process, four thermocouple sensors were used to record the pulp cavity and circumambient environment temperatures with or without air cooling. A statistical analysis of the temperatures was performed between the conditions with and without air cooling (p heat generated in the pulp cavity was lower than the threshold for dental pulp damage. These results indicate that femtosecond laser ablation with air cooling might be an appropriate method for automatic tooth preparing.

Comprehensive therapy of a fusion between a mandibular lateral incisor and supernumerary tooth: case report.

Science.gov (United States)

Onçag, Ozant; Candan, Umit; Arikan, Fatih

2005-08-01

The term fusion is used to define a developmental anomaly characterised by the union of two adjacent teeth. In the case reported here, clinical and radiographic examinations suggested a unilateral fusion between the mandibular left permanent incisor and a super-numerary tooth. Radiographs showed that the fused teeth had two distinct pulp chambers and canals. A diagnosis of chronic periapical abscess of the supernumerary tooth was made. Before root canal therapy, a periodontal surgical procedure was performed to section the central incisor and its fused supernumerary. Also, odontoplasty was performed on the roots, to establish an anatomy consistent with a normal central incisor. Later, the chronic apical abscess on the supernumerary tooth was instrumented chemo-mechanically, root canal filling was performed and an anterior composite resin restoration was placed. The patient was evaluated for one year after root canal therapy. The tooth was asymptomatic, not exhibiting any pathological root resorption or alveolar resorption, and the anterior composite restoration was intact. Instead of extracting the supernumerary tooth, the application of endodontic, periodontal, and restorative procedures proved to be an alternative treatment.

Effect of Atorvastatin on Orthodontic Tooth Movement in Male Wistar Rats

Science.gov (United States)

MirHashemi, Amir Hossein; Afshari, Maryam; Alaeddini, Mojgan; Etemad-Moghadam, Shahroo; Dehpour, Ahmadreza; Sheikhzade, Sedigheh; Akhoundi, Mohammad Sadegh Ahmad

2013-01-01

Objectives: Statins are used as cholesterol-lowering drugs by many patients and have been recently shown to affect bone metabolism. The aim of this study was to determine the effect of atorvastatinon on orthodontic tooth movement (OTM) in rats. Materials and Methods: Thirty-six adult male Sprague-Dawley rats were randomly divided into three groups of 12 samples each. Group A, served as control with no medication while groups B and C received a daily gavage of carboxymethyl cellulose (CMC) as vehicle and atorvastatin (5 mg/kg) as test substance, respectively. In all three groups, 6mm nickel-titanium closed-coil springs were ligated between the maxillary incisors and first left molars to deliver an initial force of 60g. Tooth movement was measured following sacrifice, 21 days after appliance insertion. Root resorption, PDL width and osteoclast number were histologically evaluated and compared between the groups. Results: The mean amount of tooth movement was 0.62 mm in group A, 0.59 mm in group B and 0.38 mm in group C. OTM reduction following administration of atorvastatin was statistically significant (p0.05). Conclusion: According to the results obtained in the current study, atorvastatin appears to reduce tooth movement in rats; however its effect on osteoclasts, especially osteoclastic function, requires further investigation. PMID:24910664

Acute changes in intra-alveolar tooth position and local clearance of 125I from the periodontal ligament

International Nuclear Information System (INIS)

Edwall, B.; Berg, J.O.; Gazelius, B.; Edwall, L.; Aars, H.

1987-01-01

Changes in intra-alveolar tooth position and local 125 I clearance from the periodontal ligament (PDL) were monitored simultaneously in cats. Axial tooth movements, reflecting periodontal ligament volume changes, were measured with an ultrasonic transit time technique. Local blood flow changes in the PDL were studied indirectly by measuring the local clearance of 125 I. Stimulation of the cervical sympathetic trunk caused an intrusive movement of the tooth with a concomitant reduction of the 125 I-clearance. Infusion of noradrenaline induced a similar respone. Stimulation of the inferior alveolar nerve during systemic treatment with phentolamine caused an extrusive movement of the tooth with a concomitant increase in the clearance of the tracer from the PDL. Intra-arterial infusion of the vasodilator substance P mimicked that response. Fization of the tooth to the jaw bone, thus preventing an intrusive movement, did not change the reductions in clearance seen on sympathetic stimulation, indicating that this blood flow reduction was not dependent on tooth movement. A qualitative relation between PDL blood flow (as measured by local 125 I clearance) and PDL volume (as measured by tooth position) in shown. The two variables measured are suggested to reflect two aspects of blood flow in the PDL

Circumscribed Lipoatrophy of the Chin after Tooth Extraction

Directory of Open Access Journals (Sweden)

Uwe Wollina

2017-07-01

Full Text Available We describe the rare occurrence of circumscribed facial lipoatrophy after tooth extraction. Correction by minimal invasive esthetic techniques such as soft tissue fillers or autologous fat transfer is possible but was not warranted.

Determining the direction of tooth grinding: an in vitro study.

Science.gov (United States)

ten Berge, F; te Poel, J; Ranjitkar, S; Kaidonis, J A; Lobbezoo, F; Hughes, T E; Townsend, G C

2012-08-01

The analysis of microwear patterns, including scratch types and widths, has enabled reconstruction of the dietary habits and lifestyles of prehistoric and modern humans. The aim of this in vitro study was to determine whether an assessment of microwear features of experimental scratches placed on enamel, perpendicularly to the direction of grinding, could predict the grinding direction. Experimental scratches were placed using a scalpel blade on standardised wear facets that had been prepared by wearing opposing enamel surfaces in an electromechanical tooth wear machine. These control 'baseline' facets (with unworn experimental scratches) were subjected to 50 wear cycles, so that differential microwear could be observed on the leading and trailing edges of the 'final' facets. In Group 1 (n=28), the 'footprint' microwear patterns corresponding to the known grinding direction of specimens in the tooth wear machine were identified. Then, they were used to predict the direction of tooth grinding blindly in the same sample after a 2-week intermission period. To avoid overfitting the predictive model, its sensitivity was also cross-validated in a new sample (Group 2, n=14). A crescent-shaped characteristic observed in most experimental scratches matched the grinding direction on all occasions. The best predictor of the direction of grinding was a combined assessment of the leading edge microwear pattern and the crescent characteristic (82.1% in Group 1 and 92.9% in Group 2). In conclusion, a simple scratch test can determine the direction of tooth grinding with high reliability, although further improvement in sensitivity is desirable. © 2012 Blackwell Publishing Ltd.

Micro-structural integrity of dental enamel subjected to two tooth whitening regimes.

Science.gov (United States)

Tanaka, Reina; Shibata, Yo; Manabe, Atsufumi; Miyazaki, Takashi

2010-04-01

Colour modification of tooth enamel has proven successful, but it is unclear how various bleaching applications affect micro-structural integrity of the whitened enamel. To investigate the internal structural integrity of human intact tooth enamel with the application of two commonly used whitening regimes (in-office power bleaching with 35% hydrogen peroxide and home bleaching with 10% carbamide peroxide), evaluations were performed on teeth of identical colour classification. After the bleaching applications, the enamel mineral density was quantified and visualised with micro-computed tomography. The micro-structural differences between the whitened tooth enamel samples were distinctive, though the colour parameter changes within the samples were equivalent. Home bleaching achieved colour modification by demineralisation, whereas in-office bleaching depended on redistribution of the minerals after treatment and subsequent enhanced mineralisation.

Orthodontic tooth movement and root resorption in ovariectomized rats treated by systemic administration of zoledronic acid.

Science.gov (United States)

Sirisoontorn, Irin; Hotokezaka, Hitoshi; Hashimoto, Megumi; Gonzales, Carmen; Luppanapornlarp, Suwannee; Darendeliler, M Ali; Yoshida, Noriaki

2012-05-01

The effect of zoledronic acid, a potent and novel bisphosphonate, on tooth movement and orthodontically induced root resorption in osteoporotic animals systemically treated with zoledronic acid as similarly used in postmenopausal patients has not been elucidated. Therefore, this study was undertaken. Fifteen 10-week-old female Wistar rats were divided into 3 groups: ovariectomy, ovariectomy + zoledronic acid, and control. Only the ovariectomy and ovariectomy + zoledronic acid groups underwent ovariectomies. Two weeks after the ovariectomy, zoledronic acid was administered only to the ovariectomy + zoledronic acid group. Four weeks after the ovariectomy, 25-g nickel-titanium closed-coil springs were applied to observe tooth movement and orthodontically induced root resorption. There were significant differences in the amounts of tooth movement and orthodontically induced root resorption between the ovariectomy and the control groups, and also between the ovariectomy and the ovariectomy + zoledronic acid groups. There was no statistically significant difference in tooth movement and orthodontically induced root resorption between the ovariectomy + zoledronic acid and the control groups. Zoledronic acid inhibited significantly more tooth movement and significantly reduced the severity of orthodontically induced root resorption in the ovariectomized rats. The ovariectomy + zoledronic acid group showed almost the same results as did the control group in both tooth movement and orthodontically induced root resorption. Zoledronic acid inhibits excessive orthodontic tooth movement and also reduces the risk of severe orthodontically induced root resorption in ovariectomized rats. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Effect of low-level laser therapy on tooth sensitivity induced by in-office bleaching.

Science.gov (United States)

Moosavi, Horieh; Arjmand, Nooshin; Ahrari, Farzaneh; Zakeri, Majid; Maleknejad, Fatemeh

2016-05-01

This study aimed to investigate the effect of low-level laser therapy (LLLT) on tooth sensitivity induced by in-office bleaching. Sixty-six patients enrolled in this randomized clinical trial. Following the in-office procedure with 40% hydrogen peroxide, the participants were randomly divided into three groups. The patients in group 1 received irradiation from a low-level red laser (LLRL; 660 nm, 200 mW, 15 s, 12 J/cm(2)), whereas participants in group 2 were subjected to a low-level infrared laser (LLIL; 810 nm) under similar conditions as in group 1. In group 3 (placebo), the laser treatment was the same as that in groups 1 and 2, but without energy output. The degree of tooth sensitivity was recorded at 1, 24, and 48 h after bleaching using a visual analog scale (VAS). The change in tooth shade was measured 30 days after tooth whitening. The intensity of tooth sensitivity was not significantly different between groups at 1 h after bleaching (p > 0.05). At 24 h after therapy, pain level was significantly lower in the LLIL group compared to the LLRL and placebo groups (p bleaching, VAS scores in the LLIL and LLRL groups were comparable to each other (p > 0.05) and both were significantly lower than that of the placebo group (p  0.05). LLLT with an infrared diode laser could be recommended as a suitable strategy to reduce the intensity of tooth sensitivity after in-office bleaching.

DIET EFFECT ON TOOTH DECAY WITH INDEX KPE EVALUATION IN BLANSKO

OpenAIRE

VAŠÍČKOVÁ, Pavlína

2009-01-01

Regular development of our teeth is the result of reciprocal induction processes with continual development stages. The non-interrupted development of the organism is the basic precondition of healthy dental tissues. It is, therefore, necessary to be aware of the fact that everybody takes on full responsibility for their own health. If we want to have clean and healthy teeth without tooth ache, oulitis and other problems we must take proper dental care. Tooth decay is the most widespread dise...

Drilling Deeper into tooth brushing skills: Is proactive interference an under-recognized factor in oral hygiene behavior change?

Science.gov (United States)

Thavarajah, Rooban; Kumar, Madan; Mohandoss, Anusa Arunachalam; Vernon, Lance T

2015-09-01

Proper tooth brushing is a seemingly simple motor activity that can promote oral health. Applying health theories, such as the Information-Motivation-Behavioral Skills (IMB) model, Motivational Interviewing (MI) and Integrated Health Coaching (IHC), may help optimize tooth brushing technique in those with suboptimal skills. Some motor activities, including tooth brushing, may over time become rote and unconscious actions, such that an existing habit can inhibit new learning, i.e., exert proactive interference on learning the new skill. Proactive interference may impede the acquisition of new tooth brushing skills; thus, in this report, we: (1) Review how the habit of tooth brushing is formed; (2) Postulate how proactive interference could impede the establishment of proper tooth brushing retraining; (3) Discuss the merits of this hypothesis; and (4) Provide guidance for future work in this topic within the context of an approach to behavior change that integrates IMB, MI and IHC methodology.

The saw-tooth sign as a clinical clue for intrathoracic central airway obstruction

Directory of Open Access Journals (Sweden)

Nakajima Akira

2012-07-01

Full Text Available Abstract Background The saw-tooth sign was first described by Sanders et al in patients with obstructive sleep apnea syndrome as one cause of extrathoracic central airway obstruction. The mechanism of the saw-tooth sign has not been conclusively clarified. The sign has also been described in various extrathoracic central airway diseases, such as in burn victims with thermal injury to the upper airways, Parkinson’s disease, tracheobronchomalacia, laryngeal dyskinesia, and pedunculated tumors of the upper airway. Case presentation A 61-year-old man was referred to our hospital with a two-month history of persistent dry cough and dyspnea. He was diagnosed with lung cancer located in an intrathoracic central airway, which was accompanied by the saw-tooth sign on flow-volume loops. This peculiar sign repeatedly improved and deteriorated, in accordance with the waxing and waning of central airway stenosis by anti-cancer treatments. Conclusion This report suggests that the so-called saw-tooth sign may be found even in intrathoracic central airway obstruction due to lung cancer.

Enamel cracks evaluation - A method to predict tooth surface damage during the debonding.

Science.gov (United States)

Dumbryte, Irma; Jonavicius, Tomas; Linkeviciene, Laura; Linkevicius, Tomas; Peciuliene, Vytaute; Malinauskas, Mangirdas

2015-01-01

The objective of this in vitro study was to evaluate the effect of the enamel cracks on the tooth damage during the debonding. Measurements of the cracks characteristics (visibility, direction, length, and location) were performed utilizing a scanning electron microscopy (SEM) technique and mathematically derived formulas (x=h/30, l=n*x) before and following the removal of mechanically retained metal and ceramic brackets. The likelihood of having greater extent enamel defects was higher for the teeth with pronounced cracks (odds vatios, OR=3.728), increased when the crack was located in more than one zone of the tooth (OR=1.998), and the inclination did not exceed 30-45° (OR=0.505). Using ceramic brackets the risk of greater amount tooth structure defects raised 1.45 times (OR=1.450). Enamel crack showing all these characteristics at the beginning of the orthodontic treatment and the use of ceramic brackets might predispose to higher risk of greater extent tooth surface damage after the debonding by 20.4%.

Measurement of Tooth Brushing Frequency, Time of Day and Duration of Adults and Children in Jakarta, Indonesia

Directory of Open Access Journals (Sweden)

Anton Rahardjo

2015-05-01

Full Text Available Epidemiological study of tooth brushing is essential to evaluate dental health of a country. Objective: To obtain data on tooth brushing frequency, time of day and duration from adults and children in Jakarta, Indonesia. Methods: Toothbrushes containing data loggers were distributed to 120 random families in Jakarta to record how many times a day, when and for how long subjects brushed their teeth. The families were each composed of a mother, father and two children aged between 6 and 15 years. Results: The mean brushing frequency of the population was 1.27 times per day. The majority of the tooth brushing (46% was performed in the morning. The mean tooth brushing duration of this population was 57.29 seconds. The mothers’ tooth brushing frequencies tended to be higher than that of the other family members, and the fathers tended to brush their teeth longer. Conclusion: Effective education aimed at increasing both the duration and frequency of tooth brushing from once to twice per day is urgently required in Indonesia.DOI: 10.14693/jdi.v21i3.251

Temperament and perception of tooth bleaching results

Directory of Open Access Journals (Sweden)

Katarzyna Mehr

2016-09-01

Full Text Available Background . The neurophysiological process of perceiving the results of tooth bleaching requires the correct interaction between the central nervous system and the organs of sight. Exaggerated beliefs concerning defective facial features may enhance inner attitudes about one’s own color of dentition, as well as a feeling of dissatisfaction with the degree of leaching. Objectives. The study aimed to assess the degree of the patient satisfaction with the results of tooth bleaching in relation to their temperament. Material and methods. There were 68 generally healthy volunteers, aged 28–38 years, with external discolorations of the teeth. They had never undergone dental bleaching and their frontal teeth did not have any fillings. After clinical evaluation and the completion of formalities, the patients were asked to fill in Strelau’s temperament questionnaire. Questionnaires and visual status were assessed three times by three doctors: before bleaching, and then 24 hours and two weeks after the home-bleaching operation, which was done with the use of Opalescence (Ultradent in uniform sequence. Results . There were practically no adverse side results, except a periodic dentin hypersensitivity that occurred periodically in 44 patients. The results of the visual assessment performed by the physicians did not differ. The questionnaire data showed that women were more critical of the results in relation to the expectations. Among elancholics, full satisfaction was declared by 41%, whereas among sanguine people, full satisfaction was obtained by 85%. Satisfaction with the aesthetic results was associated with bleaching by at least 4 degrees. Conclusions . Patients’ temperament affects their subjective evaluation of the effectiveness of tooth bleaching, which should be taken into consideration in the patient’s individual dental treatment plan.

Morphological study of tooth development in podoplanin-deficient mice.

Directory of Open Access Journals (Sweden)

Kenyo Takara

Full Text Available Podoplanin is a mucin-type highly O-glycosylated glycoprotein identified in several somatyic cells: podocytes, alveolar epithelial cells, lymphatic endothelial cells, lymph node stromal fibroblastic reticular cells, osteocytes, odontoblasts, mesothelial cells, glia cells, and others. It has been reported that podoplanin-RhoA interaction induces cytoskeleton relaxation and cell process stretching in fibroblastic cells and osteocytes, and that podoplanin plays a critical role in type I alveolar cell differentiation. It appears that podoplanin plays a number of different roles in contributing to cell functioning and growth by signaling. However, little is known about the functions of podoplanin in the somatic cells of the adult organism because an absence of podoplanin is lethal at birth by the respiratory failure. In this report, we investigated the tooth germ development in podoplanin-knockout mice, and the dentin formation in podoplanin-conditional knockout mice having neural crest-derived cells with deficiency in podoplanin by the Wnt1 promoter and enhancer-driven Cre recombinase: Wnt1-Cre;PdpnΔ/Δmice. In the Wnt1-Cre;PdpnΔ/Δmice, the tooth and alveolar bone showed no morphological abnormalities and grow normally, indicating that podoplanin is not critical in the development of the tooth and bone.

Morphological study of tooth development in podoplanin-deficient mice.

Science.gov (United States)

Takara, Kenyo; Maruo, Naoki; Oka, Kyoko; Kaji, Chiaki; Hatakeyama, Yuji; Sawa, Naruhiko; Kato, Yukinari; Yamashita, Junro; Kojima, Hiroshi; Sawa, Yoshihiko

2017-01-01

Podoplanin is a mucin-type highly O-glycosylated glycoprotein identified in several somatyic cells: podocytes, alveolar epithelial cells, lymphatic endothelial cells, lymph node stromal fibroblastic reticular cells, osteocytes, odontoblasts, mesothelial cells, glia cells, and others. It has been reported that podoplanin-RhoA interaction induces cytoskeleton relaxation and cell process stretching in fibroblastic cells and osteocytes, and that podoplanin plays a critical role in type I alveolar cell differentiation. It appears that podoplanin plays a number of different roles in contributing to cell functioning and growth by signaling. However, little is known about the functions of podoplanin in the somatic cells of the adult organism because an absence of podoplanin is lethal at birth by the respiratory failure. In this report, we investigated the tooth germ development in podoplanin-knockout mice, and the dentin formation in podoplanin-conditional knockout mice having neural crest-derived cells with deficiency in podoplanin by the Wnt1 promoter and enhancer-driven Cre recombinase: Wnt1-Cre;PdpnΔ/Δmice. In the Wnt1-Cre;PdpnΔ/Δmice, the tooth and alveolar bone showed no morphological abnormalities and grow normally, indicating that podoplanin is not critical in the development of the tooth and bone.

[Tooth shape and color as criteria for or against orthodontic space closure in case of a missing lateral incisor].

Science.gov (United States)

Wriedt, Susanne; Werner, Patrick; Wehrbein, Heinrich

2007-01-01

The aim of this study was to examine the esthetic parameters that are applied, more or less unconsciously, in deciding for or against orthodontic space closure in the case of aplasia or traumatic loss of lateral incisors. The width-height index for teeth 13 to 23 was measured on 200 dental students. The VITA Easyshade system was used to determine the components of the tooth color (L, C, h) and to identify differences between each tooth. Eight investigators subjectively assessed digital photographs of the subjects, opting for or against space closure. The Spearman correlation coefficients were calculated for the parameters measured. A comparison of the parameters showed that not one factor alone was responsible for the decision for or against space closure for esthetic reasons. Orthodontists were more likely to favor space closure when the canine was slightly wider and had a less pointed shape and the differences were very small between canine and central incisor in terms of hue, chroma, and lightness. We observed that the subjective decision on the esthetic aspects of space closure correlates closely with the objective criteria.

Static-transmission-error vibratory-excitation contributions from plastically deformed gear teeth caused by tooth bending-fatigue damage

Science.gov (United States)

Mark, W. D.; Reagor, C. P.

2007-02-01

To assess gear health and detect gear-tooth damage, the vibratory response from meshing gear-pair excitations is commonly monitored by accelerometers. In an earlier paper, strong evidence was presented suggesting that, in the case of tooth bending-fatigue damage, the principal source of detectable damage is whole-tooth plastic deformation; i.e. yielding, rather than changes in tooth stiffness caused by tooth-root cracks. Such plastic deformations are geometric deviation contributions to the "static-transmission-error" (STE) vibratory excitation caused by meshing gear pairs. The STE contributions caused by two likely occurring forms of such plastic deformations on a single tooth are derived, and displayed in the time domain as a function of involute "roll distance." Example calculations are provided for transverse contact ratios of Qt=1.4 and 1.8, for spur gears and for helical-gear axial contact ratios ranging from Qa=1.2 to Qa=3.6. Low-pass- and band-pass-filtered versions of these same STE contributions also are computed and displayed in the time domain. Several calculations, consisting of superposition of the computed STE tooth-meshing fundamental harmonic contribution and the band-pass STE contribution caused by a plastically deformed tooth, exhibit the amplitude and frequency or phase modulation character commonly observed in accelerometer-response waveforms caused by damaged teeth. General formulas are provided that enable computation of these STE vibratory-excitation contributions for any form of plastic deformation on any number of teeth for spur and helical gears with any contact ratios.

In vivo determination of tooth mobility after fixed orthodontic appliance therapy with a novel intraoral measurement device.

Science.gov (United States)

Konermann, Anna; Al-Malat, R; Skupin, J; Keilig, L; Dirk, C; Karanis, R; Bourauel, C; Jäger, A

2017-05-01

Valid measurement systems recording tooth mobility upon displacement within the subtle range of physiological strains are missing. Here, we introduce a novel in vivo measurement device and demonstrate a first clinical application by monitoring tooth mobility changes during retention after fixed multibracket appliance therapy. Tooth mobility was measured in vivo on 21 patients (11 female, 10 male; mean age 16.1 ± 3.1 years) by displacing the upper first incisor 0.2 mm lingually for 0.2, 0.5, 1, 2, 5, and 10 s with the novel intraoral device. Measurements were recorded directly after, as much as 2, 7, and 14 days and up to 6 months after appliance debonding. Device performance was precise and valid in clinical use. Data revealed significant interindividual varying tooth mobility, which was very high during the first 2 days after appliance removal. After 1 week, mobility values decreased, but were generally higher upon short loadings compared to long ones. After 3 months, tooth mobility was significantly lower than directly after debonding. Interestingly, males exhibited significantly less mobility than females. Our work is the first using an in vivo measurement device capable of performing and recording tooth displacements within this delicate range and in such precision. Furthermore, our findings elucidate tooth mobility changes after multibracket treatment, giving important information for retention periods. Establishment of this novel measurement device in clinical use is an important improvement when approaching the complexity of tooth mobility in vivo regarding different issues like orthodontics, periodontal disease, or bruxism.

The association between childhood obesity and tooth eruption.

Science.gov (United States)

Must, Aviva; Phillips, Sarah M; Tybor, David J; Lividini, Keith; Hayes, Catherine

2012-10-01

Obesity is a growth-promoting process as evidenced by its effect on the timing of puberty. Although studies are limited, obesity has been shown to affect the timing of tooth eruption. Both the timing and sequence of tooth eruption are important to overall oral health. The purpose of this study was to examine the association between obesity and tooth eruption. Data were combined from three consecutive cycles (2001-2006) of the National Health and Nutrition Examination Survey (NHANES) and analyzed to examine associations between the number of teeth erupted (NET) and obesity status (BMI z-score >95th percentile BMI relative to the Centers for Disease Control and Prevention (CDC) growth reference) among children 5 up to 14 years of age, controlling for potential confounding by age, gender, race, and socioeconomic status (SES). Obesity is significantly associated with having a higher average NET during the mixed dentition period. On average, teeth of obese children erupted earlier than nonobese children with obese children having on average 1.44 more teeth erupted than nonobese children, after adjusting for age, gender, and race/ethnicity (P erupted than nonobese children after adjusting for gender, age, and race. These findings may have clinical importance in the area of dental and orthodontic medicine both in terms of risk for dental caries due to extended length of time exposed in the oral cavity and sequencing which may increase the likelihood of malocclusions.

Tooth agenesis and craniofacial morphology in pre-orthodontic children with and without morphological deviations in the upper cervical spine

DEFF Research Database (Denmark)

Jasemi, Ashkan; Sonnesen, Liselotte

2016-01-01

AIM: To analyze differences in prevalence and pattern of tooth agenesis and craniofacial morphology between non syndromic children with tooth agenesis with and without upper cervical spine morphological deviations and to analyze associations between craniofacial morphology and tooth agenesis...... in the two groups together. METHODS: One hundred and twenty-six pre-orthodontic children with tooth agenesis were divided into two groups with (19 children, mean age 11.9) and without (107 children, mean age 11.4) upper spine morphological deviations. Visual assessment of upper spine morphology...... and measurements of craniofacial morphology were performed on lateral cephalograms. Tooth agenesis was evaluated from orthopantomograms. RESULTS: No significant differences in tooth agenesis and craniofacial morphology were found between children with and without upper spine morphological deviations (2.2 ± 1.6 vs...

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... Dental Advances Learn what those dental words mean. The Life of a Tooth Home | InfoBites | Find a Dentist | Your Family's Oral Health | RSS About AGD | Contact AGD | Site Map | Reprints and Permissions | Privacy Statement | Terms and Conditions © 1996-2018 Academy of General Dentistry. All Rights Reserved.

Bevarage consumption during television viewing and tooth ...

African Journals Online (AJOL)

Aim: The study assessed the television (TV) viewing habits, preferred energy and acidic drinks consumed when watching television and the history of tooth sensitivity among adolescents who watched television >2 hours daily (HTV) and <2 hour daily. (LTV). Subjects and Methods: This is a descriptive study conducted in Ife ...

Retrospective EPR dosimetry on the basis of tooth enamel analyses of Techa river area residents

International Nuclear Information System (INIS)

Wieser, A.; Romanyukha, A.A.; Kozheurov, V.P.; Degteva, M.O.

2000-01-01

The dose in tooth enamel from residents of villages along the Techa river was measured by EPR dosimetry. The results were correlated to the 90 Sr whole body burden as measured about 30 years after ingestion. Based on the results of this preliminary investigation the ingestion dose coefficient of tooth enamel for 90 Sr is estimated and compared with the value for bone surface given in ICRP. The results of the preliminary study suppose a similar metabolism of strontium for tooth dentine and the skeleton. (author)

Orthodontic-Surgical Alternatives for Tooth Ankylosis

OpenAIRE

Giraldo-Mira, Juan Felipe; Velásquez Velásquez, Mariluz

2014-01-01

Treatment for tooth ankylosis poses a big challenge in dentistry. Orthosurgical techniques must be included to obtain a satisfactory esthetic and functional result. The treatment options are surgical removal, segmentary osteotomy with immediate repo- sition and segmentary osteotomy with distraction osteogenesis, which can be done using distractors or orthodontics, thus achieving acceptable long-term outcomes. El tratamiento de dientes anquilosados presenta un gran desafio en odontologia. E...

Tooth extraction education at dental schools across Europe

NARCIS (Netherlands)

Brand, H.S.; van der Cammen, C.C.J.; Roorda, S.M.E.; Baart, J.A.

2015-01-01

Objectives/Aims: To explore students’ opinion about theoretical and clinical training in tooth extraction at different European dental schools. Materials and Methods: An online questionnaire, containing 36 dichotomous, multiple choice and Likert scale rating questions, was distributed among students

Contemporary permanent tooth dimensions, with comparisons to G.V. Black's data.

Science.gov (United States)

Harris, Edward F; Burris, Benjamin G

2003-01-01

The tooth dimensions most commonly cited in the dental literature are those published by the famous restorative dentist G. V. Black late in the 19th century. We report here on the crown dimensions of a large series of contemporary North American Whites and show that Black's values differ significantly from modern values, but not in any consistent or predictable fashion. Black supplied no information about the nature of his sample. We suggest that it may be time to replace Black's data with modern tooth size standards.

Challenges in reconstructing an isolated anterior tooth with a metal-free crown

Directory of Open Access Journals (Sweden)

Max Doria Costa

2013-01-01

Full Text Available Introduction: Currently, new esthetic treatments are available to the dentist due to the advent of ceramic-ceramic prostheses. A new option has become part of daily clinical practice, with the promise of esthetic optimization through the elimination of metal in prosthetic crowns. The translucence of these new systems allows the transmission of light through the tooth structure, minimizing gingival darkness and producing a vibrant and natural appearance. Case Report: The patient, 30 years old, female, showed with a fractured tooth crown at the cervical level in the right lateral incisive. It was observed that the tooth had prior adequate endodontic treatment. A metal-free restorative system was selected. A plaster model was obtained for subsequent tooth preparative scanning and manufacture of ceramic framework. After receiving the framework, adjustments were made and the color choice of covering ceramic, following the protocol of choice for a chroma suboptimal aiming further characterization. After the ceramics application, adjustments in shape, texture, and occlusion were made. The crown was characterized by exterior paint, getting a favorable result, restoring esthetics and function. Discussion : The metal-free systems are a viable alternative to the restorative treatment when esthetics is desired, allowing a natural and harmonious smile, combined with the reliability of the restorative material.

New laboratory methods to study tooth surface coverage and interproximal plaque control by dentifrice products.

Science.gov (United States)

Xu, Tao; Herles, Susan M; Barnes, Virginia M

2004-01-01

To develop and test an in vitro tooth model for use in conjunction with laboratory methods to study interproximal effects and efficacy of dentifrices. The application of the model should offer visual evaluation of dentifrice coverage of the tooth surface, and measure dental plaque control at posterior interdental spaces with a dentifrice. The dentifrice products tested with the model were: Colgate Total 2 in 1 Toothpaste and Mouthwash (CTTM), Colgate Total dentifrice (CTD), and Colgate Regular dentifrice (CRD). Extracted human posterior teeth were disinfected, cleaned, aligned, and mounted in denture acrylic. In the area coverage method, tooth surface coverage and penetration of two different forms of dentifrice products (CTTM and CRD) were compared using digital photography. In the interproximal plaque control method, the teeth were coated with human saliva and incubated anaerobically with a mixture of representative oral bacteria for six hours at 37 degrees C. In vitro dental plaque was assessed after brushing the facial surface with one of the three dentifrice products using a clinical plaque scoring index. The area coverage method demonstrated that both dentifrice products tested covered approximately 70% of the facial tooth surface; the CTTM dentifrice coverage on the lingual tooth surface was significantly higher than the coverage for the CRD dentifrice. With the interproximal plaque control method, in the presence of an active ingredient, the CTTM dentifrice had equivalent efficacy to the CTD dentifrice. Both CTTM and CTD were significantly superior to the CRD for interproximal dental plaque control. Using the developed tooth model, two assessment methods have been shown to have the potential to demonstrate tooth surface coverage, and to assess the potential efficacy of a dentifrice for the control of interproximal dental plaque. This process can indicate potential clinical evaluation of an oral care product, and support clinical findings with controlled

In vivo quantitative evaluation of tooth color with hand-held colorimeter and custom template.

Science.gov (United States)

Shimada, Kazuki; Kakehashi, Yoshiyuki; Matsumura, Hideo; Tanoue, Naomi

2004-04-01

This article presents a technique for quantitatively evaluating the color of teeth, as well as color change in restorations and tooth surfaces. Through use of a custom template made of a thermoplastic polymer and a dental colorimeter, tooth surface color can be recorded periodically at the same location intraorally.

Age estimation by canines' pulp/tooth ratio in an Iranian population using digital panoramic radiography.

Science.gov (United States)

Dehghani, Mahdieh; Shadkam, Elaheh; Ahrari, Farzaneh; Dehghani, Mahboobe

2018-04-01

Age estimation in adults is an important issue in forensic science. This study aimed to estimate the chronological age of Iranians by means of pulp/tooth area ratio (AR) of canines in digital panoramic radiographs. The sample consisted of panoramic radiographs of 271 male and female subjects aged 16-64 years. The pulp/tooth area ratio (AR) of upper and lower canines was calculated by AutoCAD software. Data were subjected to correlation and regression analysis. There was a significant and inverse correlation between age and pulp/tooth area ratio of upper and lower canines (r=-0.794 for upper canine and r=-0.282 for lower canine; p-value<0.001). Linear regression equations were derived separately for upper, lower and both canines. The mean difference between actual and estimated age using upper canine was 6.07±1.7. The results showed that the pulp/tooth area ratios of canines are a reliable method for age estimation in Iranians. The pulp/tooth area ratio of upper canine was better correlated with chronological age than that of lower canine. Copyright © 2018 Elsevier B.V. All rights reserved.

Cutting blade dentitions in squaliform sharks form by modification of inherited alternate tooth ordering patterns

Science.gov (United States)

Underwood, Charlie; Johanson, Zerina; Smith, Moya Meredith

2016-11-01

The squaliform sharks represent one of the most speciose shark clades. Many adult squaliforms have blade-like teeth, either on both jaws or restricted to the lower jaw, forming a continuous, serrated blade along the jaw margin. These teeth are replaced as a single unit and successor teeth lack the alternate arrangement present in other elasmobranchs. Micro-CT scans of embryos of squaliforms and a related outgroup (Pristiophoridae) revealed that the squaliform dentition pattern represents a highly modified version of tooth replacement seen in other clades. Teeth of Squalus embryos are arranged in an alternate pattern, with successive tooth rows containing additional teeth added proximally. Asynchronous timing of tooth production along the jaw and tooth loss prior to birth cause teeth to align in oblique sets containing teeth from subsequent rows; these become parallel to the jaw margin during ontogeny, so that adult Squalus has functional tooth rows comprising obliquely stacked teeth of consecutive developmental rows. In more strongly heterodont squaliforms, initial embryonic lower teeth develop into the oblique functional sets seen in adult Squalus, with no requirement to form, and subsequently lose, teeth arranged in an initial alternate pattern.

Rehabilitating a patient with bruxism-associated tooth tissue loss: a literature review and case report.

Science.gov (United States)

Yip, Kevin Hak-Kong; Chow, Tak W; Chu, Frederick C S

2003-01-01

Tooth tissue loss from bruxism has been demonstrated to be associated with various dental problems such as tooth sensitivity, excessive reduction of clinical crown height, and possible changes of occlusal relationship. A literature search revealed a number of treatment modalities, with an emphasis on prevention and rehabilitation with adhesive techniques. Rehabilitating a patient with bruxism-associated tooth tissue loss to an acceptable standard of oral health is clinically demanding and requires careful diagnosis and proper treatment planning. This article describes the management of excessive tooth tissue loss in a 43-year-old woman with a history of bruxism. The occlusal vertical dimension of the patient was re-established with the use of an acrylic maxillary occlusal splint, followed by resin composite build-up. Full-mouth oral rehabilitation ultimately involved constructing multiple porcelain veneers, adhesive gold onlays, ceramo-metal crowns, and fixed partial dentures.

REGISTRATION OF INTERNAL MORPHOLOGICAL CHARACTERISTICS OF THE TOOTH USING DENTAL PHOTOGRAPHY

Directory of Open Access Journals (Sweden)

Todor T. Uzunov

2015-01-01

Full Text Available Purpose: Dental photography plays important role in the transfer of information between dentists as well as in communication between them and the dental technicians. It is very important to take precise photos of external and internal morphological characteristics of the teeth. There are different methods for that. The aim is to establish a protocol for registration of internal morphological characteristics of teeth by digital dental photography. Material and methods: For the accomplishment of the aim60intact frontal teeth of 30 patients aged between 18 and 20 years were photographed. The following basic and additional devices for dental photography were used: 1. Digital SLR (DSLR: • Body - Nikon D90 • Lens - Nikon AF-S Micro Nikkor 105 f / 2.8G VR • Flash - Nikon SB-R-200 Speedlight remote kit R1 2. Lingual contraster 3. Reflective disk with silver surface Lingual contraster was placed behind the respective tooth when taking photos. Light reflector was placed sideways near patient’s head. The head of the flash that is near to the reflector was oriented towards it. The other flash on the opposite side, activated at a minimum power, was directed to the tooth row. Results: Internal characteristics of the tooth - enamel cracks, translucency, transparency, opacity and opalescence were easily and predictably recorded by the described methodology. Conclusions: The method suggested by us can be successfully used for recording the internal morphological characteristics of the tooth.

The Effects of Irradiation and Calcium-deficient Diet on the Expression of Bone Morphogenetic Protein-2/4 during Early Tooth Development

International Nuclear Information System (INIS)

Park, Dai Hee; Hwang, Eui Hwan; Lee, Sang Rae

2000-01-01

To investigate the expression of bone morphogenetic protein (BMP)-2/4 during early tooth development after irradiation and calcium-deficient diet. The pregnant three-week-old Sprague-Dawley rats were used for the study. The control group was non-irradiation/normal diet group (Group 1), and the experimental groups were irradiation/normal diet group (Group 2) and irradiation/calcium-diet group (Group 3). The abdomen of the rats at the 9th day of pregnancy were irradiated with single dose of 350 cGy. The rat pups were sacrificed at embryonic 18 days, 3 days and 14 days after delivery and the maxillae tooth germs were taken. The tissue sections of specimen were stained immunohistochemically with anti-BMP-2/4 antibody. At embryo-18 days, immunoreacivity for BMP-2/4 of the Group 1 was modetate in stratum intermedium of dental organ and weak in dental papilla and dental follicle, but that of Group 2 was weak in cell layer of dental organ, and no immunoreacivity was shown in dental papilla and dental follice of Group 2 and in all tissue components of the Group 3. At postnatal-3 days, immunoreacivity for BMP-2/4 of the Group 1 was strong in cell layer of dental organ, odontoblasts and developing alveolar bone, but that of Group of 2 and Group 3 was weak in odontoblasts and developing alveolar bone. At postnatal-14 days, immunoreacivity for BMP-2/4 of the Group 1 was strong in newly formed cementum, alveolar bone and odontoblasts, but that of Group 2 was weaker than that of Group 1. In the Group 3, tooth forming cell layer showed weak immunoreactivity, but other cell layers showed no immunoreactivity. The expression of bone morphogenetic protein (BMP)-2/4 during early tooth development was disturbed after irradiation and calcium-deficient diet.

The Effects of Irradiation and Calcium-deficient Diet on the Expression of Bone Morphogenetic Protein-2/4 during Early Tooth Development

Energy Technology Data Exchange (ETDEWEB)

Park, Dai Hee; Hwang, Eui Hwan; Lee, Sang Rae [Dept. of Oral and Maxillofacial Radiology, College of Dentistry, Kyunghee University, Seoul (Korea, Republic of)

2000-09-15

To investigate the expression of bone morphogenetic protein (BMP)-2/4 during early tooth development after irradiation and calcium-deficient diet. The pregnant three-week-old Sprague-Dawley rats were used for the study. The control group was non-irradiation/normal diet group (Group 1), and the experimental groups were irradiation/normal diet group (Group 2) and irradiation/calcium-diet group (Group 3). The abdomen of the rats at the 9th day of pregnancy were irradiated with single dose of 350 cGy. The rat pups were sacrificed at embryonic 18 days, 3 days and 14 days after delivery and the maxillae tooth germs were taken. The tissue sections of specimen were stained immunohistochemically with anti-BMP-2/4 antibody. At embryo-18 days, immunoreacivity for BMP-2/4 of the Group 1 was modetate in stratum intermedium of dental organ and weak in dental papilla and dental follicle, but that of Group 2 was weak in cell layer of dental organ, and no immunoreacivity was shown in dental papilla and dental follice of Group 2 and in all tissue components of the Group 3. At postnatal-3 days, immunoreacivity for BMP-2/4 of the Group 1 was strong in cell layer of dental organ, odontoblasts and developing alveolar bone, but that of Group of 2 and Group 3 was weak in odontoblasts and developing alveolar bone. At postnatal-14 days, immunoreacivity for BMP-2/4 of the Group 1 was strong in newly formed cementum, alveolar bone and odontoblasts, but that of Group 2 was weaker than that of Group 1. In the Group 3, tooth forming cell layer showed weak immunoreactivity, but other cell layers showed no immunoreactivity. The expression of bone morphogenetic protein (BMP)-2/4 during early tooth development was disturbed after irradiation and calcium-deficient diet.

Age-related tooth wear differs between forest and savanna primates.

Directory of Open Access Journals (Sweden)

Jordi Galbany

Full Text Available Tooth wear in primates is caused by aging and ecological factors. However, comparative data that would allow us to delineate the contribution of each of these factors are lacking. Here, we contrast age-dependent molar tooth wear by scoring percent of dentine exposure (PDE in two wild African primate populations from Gabonese forest and Kenyan savanna habitats. We found that forest-dwelling mandrills exhibited significantly higher PDE with age than savanna yellow baboons. Mandrills mainly feed on large tough food items, such as hard-shell fruits, and inhabit an ecosystem with a high presence of mineral quartz. By contrast, baboons consume large amounts of exogenous grit that adheres to underground storage organs but the proportion of quartz in the soils where baboons live is low. Our results support the hypothesis that not only age but also physical food properties and soil composition, particularly quartz richness, are factors that significantly impact tooth wear. We further propose that the accelerated dental wear in mandrills resulting in flatter molars with old age may represent an adaptation to process hard food items present in their environment.

Use of an Implant O-Ring Attachment for the Tooth Supported Mandibular Overdenture: A Clinical Report

Science.gov (United States)

Guttal, Satyabodh S.; Tavargeri, Anand K.; Nadiger, Ramesh K.; Thakur, Srinath L.

2011-01-01

Retention of a mandibular denture can be achieved by an implant-retained or natural tooth-retained bar and stud attachment in the anterior segment of the mandible. The same design principles holds true for both implant-retained and tooth-retained methods of anchoring the bar and stud attachment. A simple and cost effective treatment for more complex implant overdenture is the concept of conventional tooth-retained overdentures. When few firm teeth still remain in a compromised dentition, preservation of these teeth for overdentures can improve retention and stability. The authors present a clinical report of a patient treated with a mandibular tooth-borne overdenture with bar and O-ring attachment. A splinted bar supported the prosthesis and an O-ring retained the denture. PMID:21769276

Use of an implant o-ring attachment for the tooth supported mandibular overdenture: a clinical report.

Science.gov (United States)

Guttal, Satyabodh S; Tavargeri, Anand K; Nadiger, Ramesh K; Thakur, Srinath L

2011-07-01

Retention of a mandibular denture can be achieved by an implant-retained or natural tooth-retained bar and stud attachment in the anterior segment of the mandible. The same design principles holds true for both implant-retained and tooth-retained methods of anchoring the bar and stud attachment. A simple and cost effective treatment for more complex implant overdenture is the concept of conventional tooth-retained overdentures. When few firm teeth still remain in a compromised dentition, preservation of these teeth for overdentures can improve retention and stability. The authors present a clinical report of a patient treated with a mandibular tooth-borne overdenture with bar and O-ring attachment. A splinted bar supported the prosthesis and an O-ring retained the denture.

Endodontic treatment and esthetic management of a primary double tooth with direct composite using silicone buildup guide

Directory of Open Access Journals (Sweden)

Vinaya Kumar Kulkarni

2012-01-01

Full Text Available Gemination and fusion are morphological dental anomalies, characterized by the formation of a clinically wide tooth. Gemination occurs when one tooth bud tries to divide, while fusion occurs if two buds unite. The terms double teeth, double formation, conjoined teeth, geminifusion, vicinifusion and dental twinning are often used to describe fusion and gemination. Double teeth are associated with clinical problems such as poor esthetics, spacing problems and caries susceptibility. Management of such cases requires a comprehensive knowledge of the clinical entity as well as the problems associated with it. This report presents a case of primary double tooth in a 6-year-old boy involving maxillary left central incisor. The anomalous tooth was carious and pulpally involved. This was treated conservatively by endodontic treatment and esthetic rehabilitation was done with direct composite restoration using a silicone buildup guide. The treated tooth was followed up until exfoliation.

Tooth enamel sample preparation using alkaline treatment in ESR dosimetry

International Nuclear Information System (INIS)

Yongzeng, Zhou; Jiadong, Wang; Xiaomei, Jia; Ke, Wu; Jianbo, Cong

2002-01-01

Tooth enamel sample preparation using alkaline treatment was studied and compared with traditional mechanical method in this paper. 20 adult teeth were used. Samples were placed into NaOH solution. This method requires 4-5 weeks and the enamel was separated from dentin. Experimental results show that 8M NaOH was appropriate for separating enamel from dentin and that there is no difference in background signal relative intensity between samples prepared by mechanical and by chemical methods. There is also no difference in radiosensitivity between samples prepared by two methods mentioned above. Dose response curve for tooth enamel samples isolated by 8M NaOH solution was obtained

Use of an Implant O-Ring Attachment for the Tooth Supported Mandibular Overdenture: A Clinical Report

OpenAIRE

Guttal, Satyabodh S.; Tavargeri, Anand K.; Nadiger, Ramesh K.; Thakur, Srinath L.

2011-01-01

Retention of a mandibular denture can be achieved by an implant-retained or natural tooth-retained bar and stud attachment in the anterior segment of the mandible. The same design principles holds true for both implant-retained and tooth-retained methods of anchoring the bar and stud attachment. A simple and cost effective treatment for more complex implant overdenture is the concept of conventional tooth-retained overdentures. When few firm teeth still remain in a compromised dentition, pres...

Tooth wear : a systematic review of treatment options

NARCIS (Netherlands)

Muts, Erik-Jan; van Pelt, Hans; Edelhoff, Daniel; Krejci, Ivo; Cune, Marco

2014-01-01

STATEMENT OF PROBLEM: Treatment of tooth wear is increasing. Because no evidence-based guidelines are available, the clinician may have difficulties deciding which treatment option to choose to resolve complex situations. PURPOSE: The purpose of this systematic review was to identify similarities

Cortisol level and hemodynamic changes during tooth extraction at hypertensive and normotensive patients.

Science.gov (United States)

Agani, Zana Bajrami; Benedetti, Alberto; Krasniqi, Vjosa Hamiti; Ahmedi, Jehona; Sejfija, Zana; Loxha, Mergime Prekazi; Murtezani, Arben; Rexhepi, Aida Namani; Ibraimi, Zana

2015-04-01

The patients that are subjects to oral-surgical interventions produce large amounts of steroids in comparison with healthy patients which are not a subject to any dental intervention. The aim of research was to determine the level of stress hormone cortisol in serum, arterial blood pressure and arterial pulse, and to compare the effectiveness of the usage of lidocaine with adrenalin in comparison with lidocaine without adrenalin during the tooth extraction. This clinical research includes patients with indication of tooth extraction divided in hypertensive and normotensive patients. There is no important statistical distinction between groups, for the cortisol levels before, during and after tooth extraction regardless of the type of anesthetic used, while we registered higher values of systolic and diastolic values at hypertensive patients, regardless of the type of anesthetic. There is significant systolic and diastolic blood pressure rise in both groups of patients hypertensive and normotensive patients, (regardless of anesthetic used with or without vasoconstrictor), who underwent tooth extraction. The special emphasize is attributed to hypertensive patients where these changes are more significant. As per cortisol level and pulse rate, our results indicate no significant statistical difference in between groups.

Life of a Tooth: A Visual Timeline

Medline Plus

Full Text Available ... Dentist Your Family's Oral Health About the AGD Dental care and oral health information you need from the Academy of General Dentistry Friday, May 11, 2018 About | Contact InfoBites Quick Reference ... Resin (White Filling)? Check Menstrual Calendar for Tooth Extraction What is Dental Amalgam (Silver Filling)? Learn what those dental words ...

Apoptotic cell elimination during early tooth development

Czech Academy of Sciences Publication Activity Database

Matalová, Eva; Míšek, Ivan; Chovancová, Eva

2003-01-01

Roč. 72, č. 7 (2003), s. 34 ISSN 0001-7213. [Congress of the European Association of Veterinary Anatomists/24./. 21.07.2002-25.07.2002, Brno] R&D Projects: GA ČR GP204/02/P112 Institutional research plan: CEZ:AV0Z5045916 Keywords : tooth development Subject RIV: FF - HEENT, Dentistry

Restoration of the endodontically treated posterior tooth

Directory of Open Access Journals (Sweden)

Andrea Polesel

2014-06-01

Results and conclusions: Direct adhesive restorations, indirect bonded restorations and traditional full crown are three therapeutic options for the single posterior endodontically treated teeth. The amount of remaining sound tooth structure is the most significant factor influencing the therapeutic approach. The clinician's operative skill is a determining aspect for long-term success of adhesive inlays.

Diet-borne systemic inflammation is associated with prevalent tooth loss.

Science.gov (United States)

Kotsakis, Georgios A; Chrepa, Vanessa; Shivappa, Nitin; Wirth, Michael; Hébert, James; Koyanagi, Ai; Tyrovolas, Stefanos

2017-06-09

The deleterious effect of cariogenic dietary patterns on tooth loss is well characterized, but the contribution of diet-borne systemic inflammation to loss of teeth remains uncharted. Recent efforts have unveiled a protective role of single nutrients to periodontal health. However, the assessment of overall diet as a modifiable risk factor for oral health remains elusive. Thus, the aim of this study was to assess the association between diet-borne systemic inflammation and tooth loss in a representative sample of the US adult non-institutionalized population. A cross-sectional analysis of a sample of participants of the 2009-2010 and 2011-2012 continuous NHANES receiving an oral exam and providing dietary recall data was performed. Dietary inflammatory potential was assessed by the Dietary Inflammatory Index (DII), a composite measure computed based on the association between nutrients and systemic pro-inflammatory cytokine levels. The outcome measure was prevalent tooth loss. Numbers of missing teeth were regressed across quartiles of the DII using multivariable linear regression models. 6887 eligible NHANES participants were included in the analysis; participants in the highest quartile of the DII index (pro-inflammatory diet) had an average [95% CI] of 0.84 [0.24, 1.45] additional more teeth lost as compared to those in the lowest quartile of DII (anti-inflammatory diet) (p = 0.015), after adjusting for known confounders. This significant association remained in subgroup analyses, including the lowest tertiles of energy-adjusted carbohydrate intake, and in persons aged ≥50 years. Adherence to an anti-inflammatory diet is associated with fewer missing teeth. These results suggest protective dietary patterns as a modifiable protective factor for tooth loss in the US adult population and support the incorporation of tooth loss prevention in the agenda of dietary public health interventions to prevent chronic inflammatory diseases. Copyright © 2017 Elsevier Ltd

Classification of fault diagnosis in a gear wheel by used probabilistic neural network, fast Fourier transform and principal component analysis

Directory of Open Access Journals (Sweden)

Piotr CZECH

2007-01-01

Full Text Available This paper presents the results of an experimental application of artificial neural network as a classifier of the degree of cracking of a tooth root in a gear wheel. The neural classifier was based on the artificial neural network of Probabilistic Neural Network type (PNN. The input data for the classifier was in a form of matrix composedof statistical measures, obtained from fast Fourier transform (FFT and principal component analysis (PCA. The identified model of toothed gear transmission, operating in a circulating power system, served for generation of the teaching and testing set applied for the experiment.

Application of Induced Pluripotent Stem Cells Reprogrammed from Dental Pulp Cells: a Novel Approach for Tooth Regeneration

Directory of Open Access Journals (Sweden)

Xiaoyan Zhou

2011-03-01

Full Text Available Introduction: Candidate human dental stem/progenitor cells have been isolated and charac-terized from dental tissues and shown to hold the capability to differentiate into tooth-generating cells. However, ad-vances in engineering a whole tooth by these stem cells are hindered by various factors, such as the poor availability of human primitive tooth bud stem cells, difficulties in isolating and purifying dental mesenchymal stem cells and ethical controversies when using embryonic oral epithelium. As a result it is meaningful to find other autologous dental cells for the purpose of reconstructing a tooth.The hypothesis: Previous studies demonstrated that somatic cells can be reprogrammed into induced pluripotent stem cells by ex-ogenous expression Oct-4 and Sox-2. On the basis of these findings we can reasonably hypothesize that when transfected with specific transcription factors Oct-4 and Sox-2, dental pulp cells, the main cell in pulp, could also be reprogrammed into induced pluripotent stem cells, which are considered to be of best potential to regenerate a whole tooth. Evaluation of the hypothesis: After transfection with Oct-4 and Sox-2 into human dental pulp cells, the positive colonies are isolated and then identified according to the characteristics of iPS cells. These cells are further investigated the capability in differentiating into ameloblasts and odontoblasts and finally seeded onto the sur-face of a tooth-shaped biodegradable polymer scaffold to detect the ability of constructing a bioengineered tooth.

Laypeoples' preferred sources of health information on the emergency management of tooth avulsion.

Science.gov (United States)

Al-Sane, Mona; Bourisly, Nibal; Almulla, Taghreed; Andersson, Lars

2011-12-01

When planning nationwide information campaigns on the emergency management of tooth avulsion, the populations' preference to different modes of information delivery should be taken into consideration. We currently lack information on that. The aim of this study was, therefore, to assess laypeoples' preferred sources of information on the emergency management of tooth avulsion. This was a joint study undertaken by experts in media and experts in dental traumatology. Interview-assisted questionnaires were conducted on a sample of 579 adults from Kuwait. Subjects were asked to choose their three preferred sources of information on the emergency management of tooth avulsion. Subjects' responses and sociodemographic data were registered. The data were descriptively analyzed, and a chi-square test was used to assess the relation of the subjects' preferences to their registered demographics. The Internet, health care professionals, and TV were the three most preferred sources of information on the emergency management of tooth avulsion across all groups, regardless of the sociodemographic characteristics. Younger adults, singles and subjects with higher education significantly preferred the Internet. Older adults preferred TV. Family was a preferred source in geographic districts populated with extended families, while friends were a preferred source in geographic districts populated by expatriates. Younger people and those with higher education can be effectively targeted through the Internet, while it is more effective to target older people through TV. Information, on tooth avulsion management, given by health care professionals is preferred across all population segments. © 2011 John Wiley & Sons A/S.

Hydroxyapatite coating on damaged tooth surfaces by immersion

International Nuclear Information System (INIS)

Lim, Byoung-Ki; Ryu, Su-Chak; Sun, Fangfang; Koh, Kwangnak; Han, Dong-Wook; Lee, Jaebeom

2009-01-01

Hydroxyapatite (HAp) was coated on scratched areas of a human tooth and HAp disks by the immersion method in a HAp colloidal solution (≤20 μm of average diameter dispersed in DI water). The surface morphologies of the scratched area after immersion for 1-3 months were investigated showing that the damaged surfaces were remarkably recovered. Then, the mechanical property and chemical stability of the HAp coating layers on both specimens were determined via the Vickers hardness test and concentration measurement of extracted Ca 2+ ions, respectively, after strong acidic treatment. The cellular behavior of mouse calvaria-derived pre-osteoblastic cells (MC3T3-E1) was also examined on the HAp layers regenerated on micro-scratched HAp disks for the purpose of their potential applications on maxillofacial bone conservation and reconstruction for prosthetic dentistry, and artificial disk preparation of a vertebral column. The notable loss of Ca 2+ ions under a highly acidic condition was not observed in the layers coated by HAp adsorption, indicating that the coating surface was well adhered with the original surfaces of the respective specimen. Moreover, the HAp adsorption did not adversely affect the adhesion, growth and proliferation of MC3T3-E1 cells on the coated HAp layers for up to 21 days. These results suggest that the HAp coating on the scratched areas of the tooth would be effectively applicable for the development of long-term prevention of micro-cleavage and tooth health supporters to reduce discoloration and further maxillofacial and orthopedic applications.

Clinical Evaluation of Periodontal Tissue Status in Prosthodontic Treatment of Patients with Partial Tooth Loss and Generalized Periodontitis

Directory of Open Access Journals (Sweden)

A. Kushlyk

2018-01-01

Full Text Available The problem of selection and application of dental prostheses in periodontal disease is especially relevant in case of severe generalized periodontitis, which is accompanied by mobile tooth removal resulting in overloading the periodontium of the remaining teeth as well as the increase in tooth mobility. Therefore, in generalized periodontitis, it is important to apply the method of direct dental prosthetic rehabilitation since, in case of partial tooth loss, it will prevent the development of generalized periodontitis complications. The objective of the research was to improve the effectiveness of combination therapy for patients with generalized periodontitis and partial tooth loss applying the developed method of direct fixed dental prosthetic rehabilitation based on the study of the periodontal status. Materials and methods. The study included 129 patients with general periodontitis, II-III degree and partial tooth loss over the age of 45 years. According to prosthodontic treatment, all the patients were divided into three groups: Group I consisted of 42 (20 women and 22 men patients who immediately after tooth extraction were rehabilitated with the application of direct plastic laminar immediate prosthesis and selective tooth grinding; permanent dental prosthetic rehabilitation was performed 6 weeks after tooth extraction; Group II included 43 (21 women and 22 men patients who underwent traditional permanent dental prosthetic rehabilitation using fixed dental bridges 6 weeks after mobile tooth removal and wound healing; Group III comprised 44 (21 women and 23 men patients who immediately after mobile tooth removal were rehabilitated with the application of direct fixed sectional dental bridge (Ukrainian patent UA 20995. 2007 Feb 15 and selective tooth grinding; permanent dental prosthetic rehabilitation was performed 6 months after tooth extraction. The control group consisted of 26 people with intact dentitions over the age of 45 years

The Effect of Ovariectomy and Orchiectomy on Orthodontic Tooth Movement and Root Resorption in Wistar Rats.

Science.gov (United States)

Seifi, Massoud; Ezzati, Baharak; Saedi, Sara; Hedayati, Mehdi

2015-12-01

Root resorption (RR) after orthodontic tooth movement (OTM) is known as a multifactorial complication of orthodontic treatments. Hormonal deficiencies and their effect on bone turnover are reported to have influences on the rate of tooth movement and root resorption. This study was designed to evaluate the effect of female and male steroid sex hormones on tooth movement and root resorption. Orthodontic appliances were placed on the right maxillary first molars of 10 ovariectomized female and 10 orchiectomized male Wistar rats as experimental groups and 10 female and 10 male healthy Wistar rats as control groups. NiTi closed-coil springs (9mm, Medium, 011"×.030", Ortho Technology(®); Tampa, Florida) were placed between the right incisors and the first right maxillary molars to induce tipping movement in the first molars with the application of a 60g force. After 21 days, the rats were sacrificed and tooth movement was measured by using a digital caliper (Guanglu, China). Orthodontic induced root resorption (OIRR) was assessed by histomorphometric analysis after hematoxylin and eosin staining of sections of the mesial root. The rate of tooth movement was significantly higher in all female rats, with the root resorption being lower in the experimental group. The rate of tooth movement in experimental male rats was significantly higher than the control group (p= 0.001) and the rate of root resorption was significantly lower in the experimental group (p= 0.001). It seems that alterations in plasma levels of estrogen, progesterone, and testosterone hormones can influence the rate of OTM and RR. The acceleration in tooth movement increased OTM and decreased RR.

Effect of mangosteen peel extract combined with demineralized freezed-dried bovine bone xenograft on osteoblast and osteoclast formation in post tooth extraction socket

Directory of Open Access Journals (Sweden)

Utari Kresnoadi

2016-12-01

Full Text Available Background: Tooth extraction, a common procedure in dentistry, can cause bone resorption during socket healing. Therefore, it is important to perform socket preservation procedure to maintain alveolar bone. Providing a combination of mangosteen peel extract with demineralized freezed-dried bovine bone xenograft (DFDBBX in tooth extraction socket was expected to accelerate alveol bone formation. Purpose: This study aims to determine the effect of mangosteen peel extract combined with DFDBBX introduced into the socket of post tooth extraction on the formation of osteoblasts and osteoclasts. Method: Twenty-eight (28 Cavia cobayas were divided into four groups. Extraction to the lower left incisor of Cavia cobaya was performed. The extraction socket was filled with 25 gram of PEG (group I as a control, active materials consisted of mangosteen peel extract and DFDBBX 0.5% (group II, active materials consisted of mangosteen peel extract and DFDBBX 1% (group III, and active materials consisted of mangosteen peel extract and DFDBBX 2% (group IV. After thirty days, those Cavia cobayas were sacrificed. By using HE on Histopatological examination, the number of osteoblasts and osteoclasts were measured by light microscope with 400 times of magnification. The statistical analysis was then performed using oneway Anova & TukeyHSD test. Result: The component active materials consisted of mangosteen peel extract and DFDBBX 2% had the most significant results related to the formation of osteoblasts and osteoclasts. Conclusion: Mangosteen peel extract combined with DFDBBX can increase osteoblasts and decrease osteoclasts in the socket of tooth extraction in Cavia cobaya. The combination of mangosteen peel extract and DFDBBX 2% is the most effective material in increasing osteoblast and decreasing osteoclast.

Charcot-Marie-Tooth disease type 1A

DEFF Research Database (Denmark)

Hertz, Jens Michael; Børglum, A D; Brandt, C A

1994-01-01

Charcot-Marie-Tooth disease type 1A (CMT1A) is an autosomal dominant peripheral neuropathy associated with a DNA duplication on chromosome 17p11.2-p12 in the majority of cases. Most of the sporadic cases are due to a de novo duplication. We have screened for this duplication in 11 Danish patients...

Effects of loxoprofen on the apical root resorption during orthodontic tooth movement in rats.

Science.gov (United States)

Yamamoto, Taeko; Kaku, Masato; Sumi, Hiromi; Yashima, Yuka; Izumino, Jin; Tanimoto, Kotaro

2018-01-01

Studies have revealed that severe apical root resorption during tooth movement is caused by the noninfective inflammatory reaction of apical root tissues. We hypothesized that loxoprofen can suppress apical root resorption during tooth movement. Cyclic tensile force (CTF) of 10 kPa was applied to the human pulp cells for 48 hours by the Flexcell Strain Unit. Loxoprofen (10 and 100 μM) was added to the culture cells, and expression of cyclooxygenase (COX)-1, COX-2, interleukin (IL)-1β, receptor activator of nuclear factor kappa-B ligand (RANKL), tumor necrosis factor (TNF)-α, and macrophage colony-stimulating factor (M-CSF) were examined. To determine the effects of loxoprofen sodium on apical root reabsorption during tooth movement, the upper first molars of 7-week-old rats were subjected to mesial movement by 10g force for 30 days with or without the oral administration of loxoprofen. Gene expression and protein concentration of COX-1, COX-2, IL-1β, TNF-α, RANKL and M-CSF were significantly higher in the CTF group than in the control group. However, these levels were decreased by loxoprofen administration. After orthodontic tooth movement, the expression of IL-1β, TNF-α, RANKL and M-CSF decreased in the loxoprofen group than in the control group by immunohistochemical staining. In comparison to control group, less number of odontoclasts and a decrease in the amount of apical root resorption was observed in the loxoprofen group. Many osteoclasts became visible on the pressure side of the alveolar bone in the both groups, and the amount of tooth movement did not show a significant difference. These findings demonstrate that severe apical root resorption may be suppressed by loxoprofen administration, without a disturbance of tooth movement.

Hypercementosis and odontogenic epithelial hyperplasia associated with a tooth root remnant mimicking a neoplasm. A case report.

Science.gov (United States)

Zustin, J; Friedrich, R E

2010-01-01

Hypercementosis presents as painless, single or multiple non-neoplastic cementum formation beyond the physiological limits of the tooth. It often occurs in the apical area of the involved tooth following infection, chemical or mechanical trauma. We report on radiographic and histopathological findings in a single case of late intraosseous hypercementosis and odontogenic epithelial hyperplasia associated with a minute apical tooth root remnant years after its extraction, mimicking a tumour.

Maxillary anterior tooth dimensions and proportions in an Irish young adult population.

LENUS (Irish Health Repository)

Condon, M

2011-07-01

This study was undertaken in a young Irish population to determine the dimensions and ratios of the six maxillary anterior teeth. One hundred and nine Irish subjects (age 18-25 inclusive) had irreversible hydrocolloid impressions made of their maxillary dentition poured in type V stone. Clinical crown dimensions were measured with a digital calliper. The stone casts were digitally photographed in a standardised manner enabling calculation of various ratios between the maxillary anterior teeth. Sexual dimorphism existed for various tooth dimensions; most notably canine teeth were in the region of 0·8 mm longer and 0·6 mm wider in males. Central and lateral incisors were found to be 0·5 mm wider in males. It is, therefore, recommended that dimensional tooth guidelines should be given for each of the sexes and not on a population basis. With regard to tooth proportion ratios, no significant differences were found between genders or the left and right sides for any of the measurements or ratios measured. The digitally recorded tooth proportions were similar for both sexes, and the Golden Proportion guidelines could only be applied to the lateral incisor\\/central incisor widths (0·618). Identified width proportions for the canine\\/central incisor were 0·58 and for canine\\/lateral incisor 0·89.

Tooth display and lip position during spontaneous and posed smiling in adults.

Science.gov (United States)

Van Der Geld, Pieter; Oosterveld, Paul; Berge, Stefaan J; Kuijpers-Jagtman, Anne M

2008-08-01

To analyze differences in tooth display, lip-line height, and smile width between the posed smiling record, traditionally produced for orthodontic diagnosis, and the spontaneous (Duchenne) smile of joy. The faces of 122 male participants were each filmed during spontaneous and posed smiling. Spontaneous smiles were elicited through the participants watching a comical movie. Maxillary and mandibular lip-line heights, tooth display, and smile width were measured using a digital videographic method for smile analysis. Paired sample t-tests were used to compare measurements of posed and spontaneous smiling. Maxillary lip-line heights during spontaneous smiling were significantly higher than during posed smiling. Compared to spontaneous smiling, tooth display in the (pre)molar area during posed smiling decreased by up to 30%, along with a significant reduction of smile width. During posed smiling, also mandibular lip-line heights changed and the teeth were more covered by the lower lip than during spontaneous smiling. Reduced lip-line heights, tooth display, and smile width on a posed smiling record can have implications for the diagnostics of lip-line height, smile arc, buccal corridors, and plane of occlusion. Spontaneous smiling records next to posed smiling records are therefore recommended for diagnostic purposes. Because of the dynamic nature of spontaneous smiling, it is proposed to switch to dynamic video recording of the smile.

Pre-prosthetic minor tooth movement with elastic separating ring & provisional restoration modification: case report

Directory of Open Access Journals (Sweden)

Haneol Shin

2012-05-01

Full Text Available Proximal caries or coronal defect in posterior teeth may result in the loss of proximal space and drifting of neighboring teeth, which makes restoration difficult. Inability to restore proper contours and to align tooth axis properly are commonly encountered problems when planning tooth restoration. Moreover, tilted teeth aggravate periodontal tissue breakdown, such as pseudo-pocket, and angular osseous defect. The purpose of this case presentation is to describe a simple technique for inducing minor tooth movement with orthodontic separating ring and provisional restoration modification. This method was used to create crown placement space on mesially tilted molar. This method is easy, simple and efficient technique which could be used in interproximal space gaining in selected situation.

Regenerative Endodontic Treatment with Orthodontic Treatment in a Tooth with Dens Evaginatus: A Case Report with a 4-year Follow-up.

Science.gov (United States)

Natera, Marianella; Mukherjee, Padma M

2018-06-01

Dens evaginatus is a developmental tooth anomaly in which an extra cusp or tubercle protrudes on the occlusal surface of the tooth along with some pulpal tissue. Because of the fragile nature of the protrusion, these teeth are often at risk of pulpal exposure. When this occurs in an immature tooth, regenerative endodontic treatment may be a good treatment approach to promote root formation. There is limited literature that documents the occurrence of orthodontic treatment in teeth that have undergone regenerative endodontic therapy using triple antibiotic paste. Here we present a case of an immature premolar tooth with dens evaginatus that was diagnosed with pulp necrosis and chronic apical abscess. The tooth was treated with regenerative endodontic treatment; after which, the patient received orthodontic treatment with fixed appliances for 2 years. The tooth responded favorably to the regenerative endodontic treatment and orthodontic tooth movement. Clinically and radiographically, all the follow-up examinations revealed an asymptomatic tooth with evidence of periapical healing with stunted root development. The tooth remained asymptomatic even after 4 years. The regenerative endodontic procedure (REP) was successful in treating an immature permanent premolar with pulp necrosis and apical periodontitis with dens evaginatus. In this case, the tooth treated with an REP responded to orthodontic treatment similar to the nonendodontically treated teeth. Further studies are recommended to clarify the precise effects of orthodontic treatment on teeth treated with an REP. Copyright © 2018 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

One-stage tooth-borne distraction versus two stage bone-borne distraction in surgically assisted maxillary expansion (SARME).

Science.gov (United States)

Seeberger, Robin; Abe-Nickler, Dorothee; Hoffmann, Jürgen; Kunzmann, Kevin; Zingler, Sebastian

2015-12-01

To evaluate and compare the effects of tooth-borne and bone-borne distraction devices in surgically assisted maxillary expansion (SARME) on dental and skeletal structures. A sample of 33 skeletally mature patients with transverse maxillary deficiencies was examined with cone beam computed tomography (CBCT) before and 3 months after surgery. Fourteen patients were treated with tooth-borne devices and 19 patients with bone-borne devices. Dental crown expansion in the first premolars did not differ significantly between the two groups, and median expansion was 5.55 mm (interquartile range [IQR] 5.23) in the tooth-borne device group and 4.6 mm (IQR 3.4) in the bone-borne device group. In the first molars, crown expansion and lateral tipping were significantly greater in the tooth-borne device group (P ≤ .02). The median skeletal nasal isthmus increase was significantly more in the bone-borne device group at 3.0 mm than in the tooth-borne device group at 0.98 mm (P ≤ .02). Both tooth-borne and bone-borne devices are effective treatment modalities to correct maxillary transverse deficiencies. Bone-borne devices produced greater widening of the skeletal nasal floor and fewer dental side effects in the first molars. Copyright © 2015 Elsevier Inc. All rights reserved.

Epidemiology and Risk Factors of Tooth Loss among Iranian Adults: Findings from a Large Community-Based Study

Directory of Open Access Journals (Sweden)

Saber Khazaei

2013-01-01

Full Text Available Objectives. To investigate the prevalence of tooth loss and different prosthetic rehabilitations among Iranian adults, as well as the potential determinants of tooth loss. Methods. In a cross-sectional community-based study conducted among 8094 Iranian adults living in Isfahan province, a self-administered questionnaire was used to assess epidemiologic features of tooth loss. Results. Thirty-two percent of subjects had all their teeth, 58.6% had lost less than 6, and 7.2% of participants had lost more than 6 teeth. One hundred and sixty-nine individuals (2.2% were edentulous. Among participants, 2.3% had single jaw removable partial denture, 3.6% had complete removable denture in both jaws, and 4.6% had fixed prosthesis. Others reported no prosthetic rehabilitation (89.5%. In the age subgroup analysis (≤35 and >35 years old tooth loss was more prevalent among men than women (OR=2.8 and 1.9, resp., P35 years (adjusted OR=1.29, P<0.01. Conclusions. Tooth loss is highly prevalent in Iranian adult population. Community programs promoting oral health for prevention of tooth loss should be considered taking into account its major determinants including lower educational level, male gender, smoking, and metabolic abnormality.

Comparison of Amount of Primary Tooth Reduction Required for Anterior and Posterior Zirconia and Stainless Steel Crowns.

Science.gov (United States)

Clark, Larkin; Wells, Martha H; Harris, Edward F; Lou, Jennifer

2016-01-01

To determine if aggressiveness of primary tooth preparation varied among different brands of zirconia and stainless steel (SSC) crowns. One hundred primary typodont teeth were divided into five groups (10 posterior and 10 anterior) and assigned to: Cheng Crowns (CC); EZ Pedo (EZP); Kinder Krowns (KKZ); NuSmile (NSZ); and SSC. Teeth were prepared, and assigned crowns were fitted. Teeth were weighed prior to and after preparation. Weight changes served as a surrogate measure of tooth reduction. Analysis of variance showed a significant difference in tooth reduction among brand/type for both the anterior and posterior. Tukey's honest significant difference test (HSD), when applied to anterior data, revealed that SSCs required significantly less tooth removal compared to the composite of the four zirconia brands, which showed no significant difference among them. Tukey's HSD test, applied to posterior data, revealed that CC required significantly greater removal of crown structure, while EZP, KKZ, and NSZ were statistically equivalent, and SSCs required significantly less removal. Zirconia crowns required more tooth reduction than stainless steel crowns for primary anterior and posterior teeth. Tooth reduction for anterior zirconia crowns was equivalent among brands. For posterior teeth, reduction for three brands (EZ Pedo, Kinder Krowns, NuSmile) did not differ, while Cheng Crowns required more reduction.

Helium ion microscopy of enamel crystallites and extracellular tooth enamel matrix.

Science.gov (United States)

Bidlack, Felicitas B; Huynh, Chuong; Marshman, Jeffrey; Goetze, Bernhard

2014-01-01

An unresolved problem in tooth enamel studies has been to analyze simultaneously and with sufficient spatial resolution both mineral and organic phases in their three dimensional (3D) organization in a given specimen. This study aims to address this need using high-resolution imaging to analyze the 3D structural organization of the enamel matrix, especially amelogenin, in relation to forming enamel crystals. Chemically fixed hemi-mandibles from wild type mice were embedded in LR White acrylic resin, polished and briefly etched to expose the organic matrix in developing tooth enamel. Full-length amelogenin was labeled with specific antibodies and 10 nm immuno-gold. This allowed us to use and compare two different high-resolution imaging techniques for the analysis of uncoated samples. Helium ion microscopy (HIM) was applied to study the spatial organization of organic and mineral structures, while field emission scanning electron microscopy (FE-SEM) in various modes, including backscattered electron detection, allowed us to discern the gold-labeled proteins. Wild type enamel in late secretory to early maturation stage reveals adjacent to ameloblasts a lengthwise parallel alignment of the enamel matrix proteins, including full-length amelogenin proteins, which then transitions into a more heterogeneous appearance with increasing distance from the mineralization front. The matrix adjacent to crystal bundles forms a smooth and lacey sheath, whereas between enamel prisms it is organized into spherical components that are interspersed with rod-shaped protein. These findings highlight first, that the heterogeneous organization of the enamel matrix can be visualized in mineralized en bloc samples. Second, our results illustrate that the combination of these techniques is a powerful approach to elucidate the 3D structural organization of organic matrix molecules in mineralizing tissue in nanometer resolution.

Helium ion microscopy of enamel crystallites and extracellular tooth enamel matrix

Directory of Open Access Journals (Sweden)

Felicitas B Bidlack

2014-10-01

Full Text Available An unresolved problem in tooth enamel studies has been to analyze simultaneously and with sufficient spatial resolution both mineral and organic phases in their three dimensional (3D organization in a given specimen. This study aims to address this need using high-resolution imaging to analyze the 3D structural organization of the enamel matrix, especially amelogenin, in relation to forming enamel crystals. Chemically fixed hemi-mandibles from wild type mice were embedded in LR White acrylic resin, polished and briefly etched to expose the organic matrix in developing tooth enamel. Full-length amelogenin was labeled with specific antibodies and 10 nm immuno-gold. This allowed us to use and compare two different high-resolution imaging techniques for the analysis of uncoated samples. Helium ion microscopy (HIM was applied to study the spatial organization of organic and mineral structures, while field emission scanning electron microscopy (FE-SEM in various modes, including backscattered electron detection, allowed us to discern the gold-labeled proteins. Wild type enamel in late secretory to early maturation stage reveals adjacent to ameloblasts a lengthwise parallel alignment of the enamel matrix proteins, including full-length amelogenin proteins, which then transitions into a more heterogeneous appearance with increasing distance from the mineralization front. The matrix adjacent to crystal bundles forms a smooth and lacey sheath, whereas between enamel prisms it is organized into spherical components that are interspersed with rod-shaped protein. These findings highlight first, that the heterogeneous organization of the enamel matrix can be visualized in mineralized en bloc samples. Second, our results illustrate that the combination of these techniques is a powerful approach to elucidate the 3D structural organization of organic matrix molecules in mineralizing tissue in nanometer resolution.

Basic School Teachers' Knowledge and Attitude about Tooth Decay ...

African Journals Online (AJOL)

Basic School Teachers' Knowledge and Attitude about Tooth Decay and Practice ... Background: The important role of teachers in oral health education cannot be ... 60.3% of the teachers claimed spending time promoting for oral health.

Management of Tooth Surface Loss of Varying Etiology with Full Mouth all Ceramic Computer-Aided Design/Computer-Aided Manufacture Restorations.

Science.gov (United States)

Bettie, Nirmal Famila; Kandasamy, Saravanan; Prasad, Venkat

2017-11-01

The anatomical form of a tooth can undergo changes leading to loss of tooth form. The loss of tooth surface can be due to varying etiology. Dental caries, attrition, abrasion, erosion, involving any surface of the tooth can lead to loss of tooth structure. The rate of tooth destruction may proceed to such an extent that the esthetics, function and comfort may be lost. The role of a practioner lies in identification and screening of such case and motivate for oral rehabilitation that includes habit cessation. Computerized dentistry has raised the bar as far as esthetic restorations are concerned. Demanding esthetics has made zirconia crowns as the material of choice in full mouth rehabilitations. However, appropriate treatment planning with scientific evidence and a recommended treatment protocol with careful implementation results in successful restorations and satisfied patients.

Chapter 3: Design of the Saber-Tooth Project.

Science.gov (United States)

Ward, Phillip

1999-01-01

Used data from interviews, surveys, and document analysis to describe the methods and reform processes of the Saber Tooth Project, examining selection of sites; demographics (school sites, teachers, data sources, and project assumptions); and project phases (development, planning, implementation, and support). The project's method of reform was…

Functional convergence in bat and toothed whale biosonars

DEFF Research Database (Denmark)

Madsen, P T; Surlykke, A

2013-01-01

Echolocating bats and toothed whales hunt and navigate by emission of sound pulses and analysis of returning echoes to form a self-generated auditory scene. Here, we demonstrate a striking functional convergence in the way these two groups of mammals independently evolved the capability to sense ...

The relationship between past caries experience and tooth color determined by an opto-electronic method.

Science.gov (United States)

Kerosuo, E; Kolehmainen, L

1982-01-01

The susceptibility of a tooth to dental caries has been proposed to depend on tooth color. So far there has, however, been no reliable method for tooth color determination. The aims of this study were to evaluate the reliability of an opto-electronic method and to examine the relationship between tooth color and past caries experience. The color of upper right central incisors of 64 school-children was determined using an opto-electronic tri-stimulus color comparator. The intra- and interexaminer reliability of the method was evaluated in vitro and in vivo being 85% and 83%, respectively. To assess the past caries experience the DMFS-index was calculated. Oral hygiene and dietary habits were also assessed. No significant difference in DMFS scores was obtained between the 'white teeth' group and the 'yellow teeth' group. The conclusion is, that the practical importance of possible colorrelated differences in caries resistance is negligible due to the multifaceted nature of dental caries.

In vitro performance of DIAGNOdent laser fluorescence device for dental calculus detection on human tooth root surfaces

Directory of Open Access Journals (Sweden)

Thomas E. Rams

2017-10-01

Conclusions: Excellent intra- and inter-examiner reproducibility of autofluorescence intensity measurements was obtained with the DIAGNOdent laser fluorescence device on human tooth roots. Calculus-positive root surfaces exhibited significantly greater DIAGNOdent laser autofluorescence than calculus-free tooth roots, even with the laser probe tip directed parallel to root surfaces. These findings provide further in vitro validation of the potential utility of a DIAGNOdent laser fluorescence device for identifying dental calculus on human tooth root surfaces.

Autogenous Tooth Transplantation: A Case Report with Three-Year Follow-Up

Directory of Open Access Journals (Sweden)

Narimon Limprasert, D.D.S.

2015-09-01

Full Text Available In Thailand, it is commonly considered that autogenous tooth transplantation can only be performed by oral surgeons. Though the author is an oral surgeon, a general dental practitioner who can carry out simple surgerycanalsoperformautogenoustoothtransplantation withgoodfunctional resultsandsignificantcostsavings over other options for carefully selected patients. This report presents a case of a 16 year-old Thai male patient who underwent autogenous tooth transplantation following the surgical technique recommended by Clokie CM, et al. The right mandibular third molar was transplanted to the right mandibular second molar showing successful results with radiographic follow-up for three years.

Graphene-based wireless bacteria detection on tooth enamel

Science.gov (United States)

Mannoor, Manu S.; Tao, Hu; Clayton, Jefferson D.; Sengupta, Amartya; Kaplan, David L.; Naik, Rajesh R.; Verma, Naveen; Omenetto, Fiorenzo G.; McAlpine, Michael C.

2012-03-01

Direct interfacing of nanosensors onto biomaterials could impact health quality monitoring and adaptive threat detection. Graphene is capable of highly sensitive analyte detection due to its nanoscale nature. Here we show that graphene can be printed onto water-soluble silk. This in turn permits intimate biotransfer of graphene nanosensors onto biomaterials, including tooth enamel. The result is a fully biointerfaced sensing platform, which can be tuned to detect target analytes. For example, via self-assembly of antimicrobial peptides onto graphene, we show bioselective detection of bacteria at single-cell levels. Incorporation of a resonant coil eliminates the need for onboard power and external connections. Combining these elements yields two-tiered interfacing of peptide-graphene nanosensors with biomaterials. In particular, we demonstrate integration onto a tooth for remote monitoring of respiration and bacteria detection in saliva. Overall, this strategy of interfacing graphene nanosensors with biomaterials represents a versatile approach for ubiquitous detection of biochemical targets.

Cellular and Molecular Changes in Orthodontic Tooth Movement

Science.gov (United States)

Zainal Ariffin, Shahrul Hisham; Yamamoto, Zulham; Zainol Abidin, lntan Zarina; Megat Abdul Wahab, Rohaya; Zainal Ariffin, Zaidah

2011-01-01

Tooth movement induced by orthodontic treatment can cause sequential reactions involving the periodontal tissue and alveolar bone, resulting in the release of numerous substances from the dental tissues and surrounding structures. To better understand the biological processes involved in orthodontic treatment, improve treatment, and reduce adverse side effects, several of these substances have been proposed as biomarkers. Potential biological markers can be collected from different tissue samples, and suitable sampling is important to accurately reflect biological processes. This paper covers the tissue changes that are involved during orthodontic tooth movement such as at compression region (involving osteoblasts), tension region (involving osteoclasts), dental root, and pulp tissues. Besides, the involvement of stem cells and their development towards osteoblasts and osteoclasts during orthodontic treatment have also been explained. Several possible biomarkers representing these biological changes during specific phenomenon, that is, bone remodelling (formation and resorption), inflammation, and root resorption have also been proposed. The knowledge of these biomarkers could be used in accelerating orthodontic treatment. PMID:22125437

New therapeutic modalities to modulate orthodontic tooth movement

Directory of Open Access Journals (Sweden)

Ildeu Andrade Jr

2014-12-01

Full Text Available Modulation of orthodontic tooth movement (OTM is desirable not only to patients because it shortens treatment time, but also to orthodontists, since treatment duration is associated with increased risk of gingival inflammation, decalcification, dental caries, and root resorption. The increased focus on the biological basis of tooth movement has rendered Orthodontics a more comprehensive specialty that incorporates facets of all fields of medicine. Current knowledge raises the possibility of using new therapeutic modalities for modulation of OTM, such as corticotomy, laser therapy, vibration (low-intensity pulsed ultrasound, local injections of biomodulators and gene therapy; with the latter being applicable in the near future. They are intended to enhance or inhibit recruitment, differentiation and/or activation of bone cells, accelerate or reduce OTM, increase stability of orthodontic results, as well as assist with the prevention of root resorption. This article summarizes recent studies on each one of these therapeutic modalities, provides readers with information about how they affect OTM and points out future clinical perspectives.

Digital Radiography for Determination of Primary Tooth Length: In Vivo and Ex Vivo Studies

Directory of Open Access Journals (Sweden)

Maria D. Basso

2015-01-01

Full Text Available Background. Methods for determining the root canal length of the primary tooth should yield accurate and reproducible results. In vitro studies show some limitations, which do not allow their findings to be directly transferred to a clinical situation. Aim. To compare the accuracy of radiographic tooth length obtained from in vivo digital radiograph with that obtained from ex vivo digital radiograph. Method. Direct digital radiographs of 20 upper primary incisors were performed in teeth (2/3 radicular resorption that were radiographed by an intraoral sensor, according to the long-cone technique. Teeth were extracted, measured, and mounted in a resin block, and then radiographic template was used to standardise the sensor-target distance (30 cm. The apparent tooth length (APTL was obtained from the computer screen by means of an electronic ruler accompanying the digital radiography software (CDR 2.0, whereas the actual tooth length (ACTL was obtained by means of a digital calliper following extraction. Data were compared to the ACTL by variance analysis and Pearson’s correlation test. Results. The values for APTL obtained from in vivo radiography were slightly underestimated, whereas those values obtained from ex vivo were slightly overestimated. No significance was observed (P≤0.48 between APTL and ACTL. Conclusion. The length of primary teeth estimated by in vivo and ex vivo comparisons using digital radiography was found to be similar to the actual tooth length.

Gender differences in the association between tooth loss and obesity among older adults in Brazil.

Science.gov (United States)

Singh, Ankur; Peres, Marco Aurélio; Peres, Karen Glazer; Bernardo, Carla de Oliveira; Xavier, Andre; D'Orsi, Eleonora

2015-01-01

OBJECTIVE To analyze if differences according to gender exists in the association between tooth loss and obesity among older adults. METHODS We analyzed data on 1,704 older adults (60 years and over) from the baseline of a prospective cohort study conducted in Florianopolis, SC, Southern Brazil. Multivariable logistic regression models were used to assess the association between tooth loss and general and central obesity after adjustment for confounders (age, gender, skin color, educational attainment, income, smoking, physical activity, use of dentures, hypertension, and diabetes). Linear regressions were also assessed with body mass index and waist circumference as continuous outcomes. Interaction between gender and tooth loss was further assessed. RESULTS Overall mean body mass index was 28.0 kg/m2. Mean waist circumference was 96.8 cm for males and 92.6 cm for females. Increasing tooth loss was positively associated with increased body mass index and waist circumference after adjustment for confounders. Edentates had 1.4 (95%CI 1.1;1.9) times higher odds of being centrally obese than individuals with a higher number of teeth; however, the association lost significance after adjustment for confounders. In comparison with edentate males, edentate females presented a twofold higher adjusted prevalence of general and central obesity. In the joint effects model, edentate females had a 3.8 (95%CI 2.2;6.6) times higher odds to be centrally obese in comparison with males with more than 10 teeth present in both the arches. Similarly, females with less than 10 teeth in at least one arch had a 2.7 (95%CI 1.6;4.4) times higher odds ratio of having central obesity in comparison with males with more than 10 teeth present in both the arches. CONCLUSIONS Central obesity was more prevalent than general obesity among the older adults. We did not observe any association between general obesity and tooth loss. The association between central obesity and tooth loss depends on

3D exemplar-based random walks for tooth segmentation from cone-beam computed tomography images

Energy Technology Data Exchange (ETDEWEB)

Pei, Yuru, E-mail: peiyuru@cis.pku.edu.cn; Ai, Xingsheng; Zha, Hongbin [Department of Machine Intelligence, School of EECS, Peking University, Beijing 100871 (China); Xu, Tianmin [School of Stomatology, Stomatology Hospital, Peking University, Beijing 100081 (China); Ma, Gengyu [uSens, Inc., San Jose, California 95110 (United States)

2016-09-15

Purpose: Tooth segmentation is an essential step in acquiring patient-specific dental geometries from cone-beam computed tomography (CBCT) images. Tooth segmentation from CBCT images is still a challenging task considering the comparatively low image quality caused by the limited radiation dose, as well as structural ambiguities from intercuspation and nearby alveolar bones. The goal of this paper is to present and discuss the latest accomplishments in semisupervised tooth segmentation with adaptive 3D shape constraints. Methods: The authors propose a 3D exemplar-based random walk method of tooth segmentation from CBCT images. The proposed method integrates semisupervised label propagation and regularization by 3D exemplar registration. To begin with, the pure random walk method is to get an initial segmentation of the teeth, which tends to be erroneous because of the structural ambiguity of CBCT images. And then, as an iterative refinement, the authors conduct a regularization by using 3D exemplar registration, as well as label propagation by random walks with soft constraints, to improve the tooth segmentation. In the first stage of the iteration, 3D exemplars with well-defined topologies are adapted to fit the tooth contours, which are obtained from the random walks based segmentation. The soft constraints on voxel labeling are defined by shape-based foreground dentine probability acquired by the exemplar registration, as well as the appearance-based probability from a support vector machine (SVM) classifier. In the second stage, the labels of the volume-of-interest (VOI) are updated by the random walks with soft constraints. The two stages are optimized iteratively. Instead of the one-shot label propagation in the VOI, an iterative refinement process can achieve a reliable tooth segmentation by virtue of exemplar-based random walks with adaptive soft constraints. Results: The proposed method was applied for tooth segmentation of twenty clinically captured CBCT

Frequency and risk indicators of tooth decay among pregnant women in France: a cross-sectional analysis.

Science.gov (United States)

Vergnes, Jean-Noel; Kaminski, Monique; Lelong, Nathalie; Musset, Anne-Marie; Sixou, Michel; Nabet, Cathy

2012-01-01

Little is known on the prevalence of tooth decay among pregnant women. Better knowledge of tooth decay risk indicators during pregnancy could help to develop follow-up protocols for women at risk, along with better prevention strategies. The aim of this study was to assess the frequency of tooth decay and the number of decayed teeth per woman in a large sample of pregnant women in France, and to study associated risk indicators. A secondary cross-sectional analysis of data from a French multicentre case-control study was performed. The sample was composed of 1094 at-term women of six maternity units. A dental examination was carried out within 2 to 4 days post-partum. Socio-demographic and behavioural characteristics were obtained through a standardised interview with the women. Medical characteristics were obtained from the women's medical records. Risk indicators associated with tooth decay were identified using a negative binomial hurdle model. 51.6% of the women had tooth decay. The mean number of decayed teeth among women having at least one was 3.1 (s.d. = 2.8). Having tooth decay was statistically associated with lower age (aOR = 1.58, 95%CI [1.03,2.45]), lower educational level (aOR = 1.53, 95%CI [1.06,2.23]) and dental plaque (aOR = 1.75, 95%CI [1.27,2.41]). The number of decayed teeth was associated with the same risk indicators and with non-French nationality and inadequate prenatal care. The frequency of tooth decay and the number of decayed teeth among pregnant women were high. Oral health promotion programmes must continue to inform women and care providers about the importance of dental care before, during and after pregnancy. Future research should also assess the effectiveness of public policies related to oral health in target populations of pregnant women facing challenging social or economic situations.

Tooth-size discrepancy: A comparison between manual and digital methods

Directory of Open Access Journals (Sweden)

Gabriele Dória Cabral Correia

2014-08-01

Full Text Available INTRODUCTION: Technological advances in Dentistry have emerged primarily in the area of diagnostic tools. One example is the 3D scanner, which can transform plaster models into three-dimensional digital models. OBJECTIVE: This study aimed to assess the reliability of tooth size-arch length discrepancy analysis measurements performed on three-dimensional digital models, and compare these measurements with those obtained from plaster models. MATERIAL AND METHODS: To this end, plaster models of lower dental arches and their corresponding three-dimensional digital models acquired with a 3Shape R700T scanner were used. All of them had lower permanent dentition. Four different tooth size-arch length discrepancy calculations were performed on each model, two of which by manual methods using calipers and brass wire, and two by digital methods using linear measurements and parabolas. RESULTS: Data were statistically assessed using Friedman test and no statistically significant differences were found between the two methods (P > 0.05, except for values found by the linear digital method which revealed a slight, non-significant statistical difference. CONCLUSIONS: Based on the results, it is reasonable to assert that any of these resources used by orthodontists to clinically assess tooth size-arch length discrepancy can be considered reliable.

Ontogenetic Tooth Reduction in Stenopterygius quadriscissus (Reptilia: Ichthyosauria: Negative Allometry, Changes in Growth Rate, and Early Senescence of the Dental Lamina.

Directory of Open Access Journals (Sweden)

Daniel G Dick

Full Text Available We explore the functional, developmental, and evolutionary processes which are argued to produce tooth reduction in the extinct marine reptile Stenopterygius quadriscissus (Reptilia: Ichthyosauria. We analyze the relationship between mandible growth and tooth size, shape, and count, to establish an ontogenetic trend. The pattern in S. quadriscissus is consistent with hypotheses of tooth size reduction by neutral selection, and this unusual morphology (a functionally edentulous rostrum was produced by a series of different evolutionary developmental changes that are known for other taxa showing tooth reduction and loss. Specifically, this species evolved functional edentulism by evolutionary changes in the growth allometry of the dentition and by altering growth rates through ontogeny. This observation supports previous hypotheses that S. quadriscissus underwent ontogenetic tooth reduction. Tooth reduction in S. quadriscissus may be caused by unique selective pressures resulting from prey choice and feeding behavior, expanding our current understanding of the mechanisms producing tooth reduction.