WorldWideScience

Sample records for tomonau boeki kozo

  1. Acoustic excitation of diffusion flames with coherent structure in a plane shear layer.; Effects of acoustic excitation on combustion properties; Soshiki kozo wo tomonau sendan kakusan kaen no onkyo reiki.; Onkyo reiki ni yoru nensho tokusei no henka

    Energy Technology Data Exchange (ETDEWEB)

    Ishino, Y.; Kojima, T.; Oiwa, N.; Yamaguchi, S. [Nagoya Institute of Technology, Nagoya (Japan)

    1993-10-25

    This paper reports on experiments for acoustic excitation of plane shear structured flame. Flows of air separated into the higher velocity side and the lower velocity side by a partition on the center of a flow path merge at the measuring point to form a mixed layer with coherent structure. Fuel is supplied to this mixed layer with the flows so adjusted that the generated flame will attach to the partition on the lower velocity side. Acoustic excitation (at a sound pressure level of 100 dB to 120 dB) is performed in a speaker fitted on a wall on the higher velocity side. The paper mentions the results of the experiments as follows: the acoustic excitation produces such changes to diffusion flame in the plane shear layer as shorter flame and blue flame combustion and clarification of flame structures; as seen from spectral characteristics of temperature change in the flames, a flame acoustically excited strongly presents remarkable improvements in periodicity of the structure; as seen from sound pressure distribution in the flow direction at the measuring point, the flame zone of the flame acoustically excited strongly is positioned at the middle of the node and loop of a standing wave. 6 refs., 9 figs., 1 tab.

  2. Studies of initial stage in coal liquefaction. 4. Radical formation and structural change with thermal decomposition of coal; Ekika hanno no shoki katei ni kansuru kenkyu. 4. Netsubunkai ni tomonau radical seisei kyodo to kozo henka

    Energy Technology Data Exchange (ETDEWEB)

    Kanaji, M.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan); Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    In relation to coal liquefaction reaction, the effect of the coexistence of transferable hydrogen (TH) from process solvent on reduction of radical concentration and the effect of pre-heat treatment on average structure of coals were studied. In experiment, change in radical concentration with temperature rise was measured using the system composed of Yallourn coal and process solvent. The results are as follows. Process solvent with a wide boiling point range of 180-420{degree}C is effective in suppressing an increase in radical concentration even at higher temperature. The effect of hydrogen-donating solvent increases with TH. It was also suggested that high-boiling point constituents in solvent stabilize radicals even over 400{degree}C by vapor phase hydrogenation. The experimental results of pre-heat treatment are as follows. Although the conversion improvement effect of TH is equivalent to that of the model solvent, TH tends to produce soluble products with smaller ring numbers. It was thus suggested that pre-heat treatment in process solvent is effective to inhibit retrogressive reactions. 6 refs., 5 figs., 1 tab.

  3. Acoustic excitation of diffusion flames with coherent structure in a plane shear layer. ; Application of active combustion control to two-dimensional phase-locked arranging measurements. Soshiki kozo wo tomonau heimen sendai kakusan kaen no onkyo reiki. ; Nijigen iso heikin bunpu sokutei eno active nensho seigyo no oyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishino, Y.; Kojima, T.; Oiwa, N.; Yamaguchi, S. (Nagoya Institute of Technology, Nagoya (Japan))

    1993-11-25

    The acoustic excitation of a plane diffusion flame enhances the periodicity of organized eddy controlled combustion. In this study, to clarify an effectiveness of application of active combustion control, phase characteristics of the excited eddy flames with high periodicity have been examined. A computer-aided phase-locked averaging method was employed to obtain graphical two-dimensional contour maps of the instantaneous profiles of temperature and CH emission. Both maps consisting of eight consecutive phases indicated clearly not only the periodic behavior of the organized eddy flame, but also the gas dynamic properties peculiar to those flames with coherent structure. In addition, the profiles of local contribution of the sound field to the combustion process were examined by calculating the two-dimensional distribution of the local Rayleigh index. Calculation results of the two-dimensional distribution of the local Rayleigh index indicated that the organized eddy flames have high sensitivity to sound, and play an important role in an interaction of sound and flame. 6 refs., 9 figs.

  4. Structures of bats; Komori no kozo

    Energy Technology Data Exchange (ETDEWEB)

    Natori, M. [Institute of the Space and Astronautical Science,Tokyo (Japan); Kishimoto, N. [The University of Tokyo, Tokyo (Japan)

    1999-12-05

    This paper gives an outline of the structures of bats. Unlike birds, bats have a wing membrane structure. The membrane constituted of the skin is spread between five fingers to form the wing. The wing membrane is seen in the forelimbs and the tail. In the chest and the shoulder, the ligament sheet supports the muscles. The wing membrane is about 0.5mm in thickness, with a fiber net woven through reflecting a tension field in flying. The fiber net is composed of compound materials of elastin and collagen. The shoulder joints consists of the clavicle, scapula and humerus, which is close to human beings. The elbow joints rotate only inside the plane of the wings. The leg joints are hook-shaped, with the tendon sheath provided with ruggedness. The carpus is made up of eight bones and is characterized by the ability of spreading and storing the wings. At the time of storing the wing membrane, the finger joints are stored and, during the flight after the wings are spread, it forms the flapping wing plane. Lightweight and formation of the sturdy front edge are characteristics common to other flying creatures. The spreading and the storing are possible through the direct motion of the hands. The shoulder joints and the carpus of the human beings are closer to those of bats than to those of birds. (NEDO)

  5. Crack coke in layer heat transfer analysis; Kiretsu no shinten wo tomonau kokusu sonai dennetsu kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, Hideyuki [Tohoku University, Miyagi (Japan)

    1999-03-05

    The research method heat transfer process by physical change of the coke by heat transfer from furnace wall in the retorting of coal seam filled in coke oven and flow of the gas is very complicated chamber oven style, and it does not become clear. For the purpose of the elucidation of in layer crack generation and progress mechanism, he is (1) The expansion of the softening cohesive layer. (2) Programming rate dependence of the heat. Mechanical property value on coal seam and semi- coke layer in the retorting. (3) The creep property of softening cohesive layer and semi- coke layer. (4) The setting of crack growth condition of stress intensity factor in crack tip and fracture property value of the coke by the comparison. (5) By considering the radiative heat transfer in the crack, coke in layer thermal stress analysis was carried out. The validity of these analytical result it was confirmed by the comparison with the experimental result of crack growth. Deformation behavior in the small dry distillation furnace, and crack growth mechanism in the coke layer became clear, and the prediction of the stress as micro-crack cause of generation of heating surface side coke surface and inside became possible. The numerical analysis method of the above crack growth mechanism greatly contributes to the prediction of dry distillation heating requirement and grain size of coke lump which is an index to the coke quality. Heat on material process which is accompanied by the solidification. Contraction from the softening and material migration phenomenon have been clarified by the creative research method, while this research is directly useful for energy saving of pig ironmaking process of becoming one of the ringleaders of the CO{sub 2} generation. (translated by NEDO)

  6. Imaging of salt structure; Gan`enso kozo no imaging

    Energy Technology Data Exchange (ETDEWEB)

    Akama, K; Saeki, T [Japan National Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1996-10-01

    Due to the improvement of algorithm and the advancement of calculation performance, the imaging by depth migration before stacking is being put into practice from the viewpoint of both calculation cost and accuracy. A lot of imaging examples have been already reported from the survey areas with complicated velocity structures, such as the North Sea and the Gulf of Mexico. Effectiveness of the method has been confirmed. For imaging techniques in Japan National Oil Corporation and Japan Petroleum Exploration Co., Ltd., high-speed depth migration before stacking and high efficiency velocity structure estimation technique have been investigated. This paper describes necessary care to be taken when using depth focusing analysis (DFA) for correcting a velocity model, as an interim stage of case study. The results of depth migration before stacking using dip moveout (DMO) velocity were further inferior to the section obtained by the migration after tracking. Tendency of velocity errors was distinctly deviated with the variation of depth and horizontal position. It was not suitable for modifying the velocity model using DFA. 4 refs., 4 figs.

  7. Magnetic structure of volcanic neck; Kazangankei no jiki kozo

    Energy Technology Data Exchange (ETDEWEB)

    Makino, M; Okuma, S; Morijiri, R; Nakatsuka, T [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    This paper describes the summary and result of magnetic exploration on the Kabutoyama volcano in the city of Nishinomiya, Hyogo Prefecture, Japan. It also states the interpretation and discussion on magnetic anomaly in the volcanic conduit of the mountain by using a three-dimensional magnetic structure model. Terrain surface magnetic exploration for the Kabutoyama volcano was performed by using six traverse lines each in different azimuths with the triangulation point at the summit as the basic point and by using a proton magnetometer. The exploration results of the six traverse lines around the Kabutoyama volcano may be generalized as follows: magnetic anomaly in the vicinity of the summit is moderate with little change, but it increases to 500 nT to 2,500 nT in the vicinity of the distances of 150 m to 200 m; a peak is formed with a width of a few tens of meters; and the magnetic anomaly showed a trend of rapidly decreasing at outer sides of the peak. The results of the magnetic exploration and the magnetization intensity measurement leads to a belief that such a magnetic anomalous band of an annular form would exist corresponding to the boundary or its vicinity of andesite and granite, and the Rokko granite having magnetization intensity as small as can be neglected would be distributed at outer sides of the boundary. The result of the three-dimensional magnetic structure model calculation, which assumes the internal structure of the magnetic structure to be non-uniformly magnetized, reproduced the magnetic anomaly patterns well as compared with the observation results. 1 ref., 5 figs.

  8. Analysis of automotive tire construction. Jidosha tire no kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Ishihara, K. (Toyo Tire and Rubber Co. Ltd., Osaka (Japan))

    1993-06-15

    This paper introduces features and trends of analyzing performance and construction of automotive tires. Tires are demanded of high durability, high motion performance, good comfort performance for vibration and noise, and low fuel consumption performance. A feature of analyzing the construction is to execute a modelling assuming that a tire has air-rigid flexible structure and rubber materials show hyperelastic behavior, hypothesizing a strain energy density function. In addition, a tire is highly incompressible. Visco elasticity and anti-friction performance are also important points. Rubber and cord layers have elastic characteristic of three-dimensional perpendicular anisotropy as well as non-linearity with which characteristics change according to transformation. A structural analysis must cover from static analysis to steady dynamic analysis, non-steady dynamic analysis, and eigenvalue analysis. Thermal analysis of tires simulates phenomena by combining dynamical analysis with thermal analysis. Super-computers have now come to be used for formulating equilibrium equations using finite element methods, developing finite elements, and performing heat or visco elasticity analysis and applied analysis. 35 refs., 3 figs.

  9. Aircraft fatigue failures and duties of structural reliability analysis. Kokuki kozo no hiro hakai to kozo shinraisei kaiseki no yakuwari

    Energy Technology Data Exchange (ETDEWEB)

    Fujiwara, G [Japan Airlines Co. Ltd., Tokyo (Japan)

    1992-10-05

    The use of a commercial jet transport airplane over its life of 20 years has been increasing because of intestified competition after cancellation of the regulations. It is necessary that users of the airplane adopt such a positive way as they themselves maintain safety of their airplanes rather than they wait for feedback or technical instructions from manufacturers. This paper outlines the points at issue regarding the problem of fatigue strength which is fundamental to the safety problem, explaining by various examples that the fatigue strength problem includes phenomena of which theoretical elucidation has not been obtained. Consequently, some points to be paid attention to are cited. For instance, in the analysis of reliability in case of determining the period for initial inspection (safety life), reliability should be 95-99% which have been advised by Boeing and others, even if confidence level is 95% as usual In case of considering a fleet number in the reliability analysis, the fleet number should be reflected by grouping significant in fatigue analysis. 30 refs., 10 figs., 1 tab.

  10. Survey of regulations accompanied with isolation technology of carbon dioxide; Nisanka tanso no kakuri gijutsu ni tomonau hokisei no chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Regulations, conventions and agreements relating to the discharging liquefied carbon dioxide (CO2) into the bathypelagic zone from a cruising ships are investigated. The ocean storage of CO2 is not specifically prohibited by law, but must be regulated on a global scale because such treatment may impact the marine environment. In principle, treatment with impact on the nature is prohibited. Laws of environmental conservation are completed in European, Asian, and Pacific countries, which join international conventions and committees with high interests. It is suggested that the engineering technique of the storage should be improved to observe regulations and that an impact assessment for the ocean storage should be carefully conducted in full understanding of the basic premise of the regulatory systems or organizations. Furthermore, it is significant to study on the possible effect of the ocean storage of CO2 on global warming and life-cycle assessment inventory analysis, namely the balance of the energy budget between the separation and the ocean storage of CO2. 23 refs., 7 figs., 6 tabs.

  11. Reflector imaging by diffraction stacking with stacking velocity analysis; Jugo sokudo kaiseki wo tomonau sanran jugoho ni yoru hanshamen imaging

    Energy Technology Data Exchange (ETDEWEB)

    Matsushima, J; Rokugawa, S; Kato, Y [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Yokota, T [Japan National Oil Corp., Tokyo (Japan); Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan)

    1997-10-22

    Concerning seismic reflection survey for geometrical arrangement between pits, the scattering stacking method with stacking velocity analysis is compared with the CDP (common depth point horizontal stacking method). The advantages of the CDP supposedly include the following. Since it presumes an average velocity field, it can determine velocities having stacking effects. The method presumes stratification and, since such enables the division of huge quantities of observed data into smaller groups, more data can be calculated in a shorter time period. The method has disadvantages, attributable to its presuming an average velocity field, that accuracy in processing is lower when the velocity field contrast is higher, that accuracy in processing is low unless stratification is employed, and that velocities obtained from stacking velocity analysis are affected by dipped structures. Such shortcomings may be remedied in the scattering stacking method with stacking velocity analysis. Possibilities are that, as far as the horizontal reflection plane is concerned, it may yield stack records higher in S/N ratio than the CDP. Findings relative to dipped reflection planes will be introduced at the presentation. 6 refs., 12 figs.

  12. ons theologische seminarium

    African Journals Online (AJOL)

    Breedee: Rotterdam, 19--. C.H. Irwin het 'n “goedkoop en degelijk .... 21 Vir hom, sien die uitstekende biografie van Erasmus: a.w. Vir 'n evaluering van die boekie, dies., 155 e.v.. 22 Die boekie is ..... 63 Erasmus (a.w., 150 e.v.) wys daarop hoedat J.M. Gibson Johannes du Plessis beïnvloed het. Du Plessis het dus aan die ...

  13. Detection of travel time delay caused by dilation of an artificial fracture due to pressurization; Jinko chika kiretsu kaatsu ni tomonau toka danseiha denpa jikan henka no kenshutsu

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, K; Moriya, H; Asanuma, H; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering

    1996-10-01

    By revealing the relation between dilation of a subsurface fracture due to pressurization and travel time delay, it may be possible to measure the information as to the subsurface fracture system as a geothermal reservoir. In this study, field experiment was conducted to clarify the relation between the travel time delay of elastic waves and the dilation of fracture, pressure, and incident angles. The travel time delay of P-wave and S-wave tended to increase with the pressurization. When incident angle was about 90{degree} against the fracture, the increase was ranging between 0 and 0.2 ms. The magnitude of this delay could not be explained only by the opening of main fracture. It was considered that there were micro-crack zones around the main fracture. The difference of P-S delay depended on the pressurization and change of the pressure. The delay depended on the incident angle against the fracture. The delay of S-wave showed the polarized wave direction dependency. However, the obtained results might greatly depend on the analytical method and parameters. 4 refs., 10 figs.

  14. Evaluation stationariness of triaxial seismic while drilling and detection of reflected wave; Kosei kussaku ni tomonau danseiha no sanjiku kaiseki ni yoru hiteijo hyoka to hanshaha no kenshutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, T; Asanuma, H; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering

    1996-05-01

    This paper reports a method to detect reflected wave components contained in an elastic wave caused in association with well drilling. Measurement was made on an elastic wave caused in association with well drilling in an experimental field by using a triaxial elastic wave detector disposed in a measurement well. Analyzing the particle motion tracks in the derived elastic wave signals (to derive the main axial direction of a three-dimensional hologram) revealed that oscillation direction of the signals changes non-steadily by time centering around the S-wave oscillation direction. In addition, a sound source position was estimated during the drilling. Existence probability of the S-wave signal in the non-steady continuous signals was estimated by handling the particle motion tracks stochastically. In addition, this existence probability was used as a weighting function for a correlative analysis to detect a reflected wave from directly reaching wave components in the non-steady continuous signals. Thus, improvement in reliability of reflected wave detection was attempted. Effectiveness of this method was endorsed by the field data. 3 refs., 7 figs.

  15. Effect of burn-off on physical and chemical properties of coal char; Gas ka shinko ni tomonau sekitan char no tokusei henka

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, T.; Tamura, K.; Hashimoto, H.; Funaki, M.; Suzuki, T. [Kitami Institute of Technology, Hokkaido (Japan)

    1996-10-28

    For high-efficiency coal gasification, investigations were given on effect of coal chars with different conversion rates on coal gasification reactivity. In coal gasification, reactivity of char after pyrolysis governs the efficiency. The reference char conversion in CO2 gasification of coal (weight loss) changes linearly in the initial stage of the reaction, but the reactivity declines as the end point is approached. Char surface area is as large as 400 m{sup 2}/g in the initial stage with the conversion at 20%, but it decreases in the final stage. This phenomenon relates closely with changes in pore size and crystalline structure. Change in the Raman value R which shows incompleteness of char graphite structure and amorphous carbon ratio suggests that an active portion with high reactivity is oxidized preferentially, and a portion with low reactivity remains finally. Minerals in coal are known to accelerate the gasification. However, their catalytic effect is related with chemical forms, and complex as they may change into inactive sulfides and silicates under severe reaction conditions. Change in forms of calcium compounds may also be involved in decline of the reactivity in the latter stage. 8 refs., 4 figs.

  16. Change in catalyst properties during coal liquefaction; Kokoritsu sekitan ekika shokubai no kaihatsu (Hanno no shinko ni tomonau shokubai seijo no henka). 1

    Energy Technology Data Exchange (ETDEWEB)

    Koyama, T.; Sato, K.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

    1996-10-28

    The purpose of this study is to prevent the deactivation of catalysts recycled in the 0.1 t/d bench scale unit (BSU). Catalysts recovered during reactions in the BSU and after reactions in the 5-liter autoclave were analyzed, to investigate the influences of the reaction condition on the property and activity of catalysts. Were used {gamma}-iron oxyhydroxide ({gamma}-FeOOH), {alpha}-iron oxyhydroxide ({alpha}-FeOOH), and natural pyrite (FeS2) as catalysts. At the S/Fe atomic ration of 1.2 under the BSU reaction condition, troilite was more easily formed from {gamma}-FeOOH compared with pyrite and {alpha}-FeOOH. As the reaction proceeded through the first, second, and third reactors, the crystal size increased, the pyrrhotite content decreased, and the troilite content increased. Deactivation due to the formation of troilite was irreversible. At the S/Fe of 3.0, however, both the formation of troilite and the crystal growth of pyrrhotite were not observed. It was found that the deactivation of catalysts can be remarkably suppressed. 5 refs., 6 figs., 1 tab.

  17. Survey on weather changes associated with large-scale tree-planting. 2; Daikibo ryokuka ni tomonau kiko henka ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    An investigational study was made for large-scale tree-planting aiming at CO2 fixation. Water resource and precipitation relating to tree-planting were determined from NASA data and arranged into the global distribution map. It was found that Australia and the Chinese continent are under the relatively favorable condition. As for the soil condition, nutrition resource is short in the desert and unused zone. From the vegetation data obtained from meteorological satellite NOAA, developed was a method for estimating net primary productivity of terrestrial ecosystem and obtained was a global distribution map for the amount of CO2 fixed under the present terrestrial vegetation. At the same time, areas which have great potentiality of tree-planting were selected from the map for estimating potentiality of the global tree-planting. To study the promotion of rainfall as a means of expanding the potential tree-planting area, the conventional meteorological and physical model was improved, and more realistic simulation was made possible. Also as to the water utilization technology, the modeling method was developed. As the area having a potentiality of expanding tree-planting, Australia (especially the west) was cited as the first candidate, and China the second candidate. 108 refs., 128 figs., 49 tabs.

  18. Metal droplet holdup in the thick slag layer subjected to bottom gas injection; Gas sokofuki wo tomonau atsui slag sonai ni okeru metal teki no holdup

    Energy Technology Data Exchange (ETDEWEB)

    Takashima, S; Iguchi, M [Hokkaido University, Sapporo (Japan)

    2000-04-01

    Model experiments were carried out to investigate the bubble and liquid flow characteristics in a bottom blowing bath covered with a thick slag layer typical of in-bath smelting reduction processes. An aqueous ZnCl{sub 2} solution and silicone oil were used as the models for molten metal and molten slag, respectively. The density ratio of the solution to the silicone oil was 1.7, being close to a steel/slag density ratio of 2.0 to 2.2 in practice. The diameter of a vessel containing the two liquids was changed over a wide range. The holdup of the solution carried up by bubbles into the upper silicone oil layer was measured with a suction tube. The volume of the solution, V{sub m}, was dependent mainly on the density difference. Empirical correlations of V{sub m} and the penetration height of the solution were derived. (author)

  19. Transient heat characteristics of water-saturated porous media with freezing; Toketsu wo tomonau gansui takoshitsu sonai no hiteijo netsu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, A [Akita National College of Technology, Akita (Japan)

    1998-02-25

    Analytical and experimental investigations were performed to examine the transient heat characteristics of water-saturated porous media with freezing. As a physical model, a two-dimensional vertical cavity was considered. One vertical wall was abruptly cooled below the fusion temperature. Other three walls were thermally insulated. Three different sizes of glass, and iron, alumina and copper beads were used as the porous media in this study. The cold energy stored up in the porous media and the average thickness of frozen layer were measured in the experiments. Comparisons of the analytical results with the experimental ones were made, and the effects of Darcy number, Stefan number and modified Prandtl number on the transient heat characteristics were discussed. The dimensionless equations for predicting the averaged frozen layer thickness and the stored cold energy were obtained as a function of various dimensionless parameters. 8 refs., 16 figs., 1 tab.

  20. Study on the distribution of streaming potential while groundwater pumping up; Chikasui no kumiage ni tomonau ryudo den`i hassei ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H; Shima, H; Sakurai, K [OYO Corp., Tokyo (Japan)

    1997-10-22

    This paper describes effectiveness of water channel prospecting by means of streaming potential method. To investigate the distribution of streaming potential on the ground surface while groundwater pumping up, some laboratory experiments were performed. A system was constructed, in which fluid is flowed in an experimental cistern from its both ends and self-flowed through a strainer pipe fixed for flowing out the fluid at the center of the cistern. Streaming potential with the flowing of the fluid was observed. Positive streaming potential waveform was generated with the flowing of the fluid, and the potential increased with approaching the strainer pipe. A groundwater pumping test facility was used as a field test site. There was a positive maximal point of potential distribution at about 30 m far from the pumping well in the southeast direction. The potential gradually decreased in the eastern part from the maximal point. The potential steeply decreased in the northwest direction from the pumping well. From these experiments, it was found that the groundwater flow and underground structures can be reflected by the distribution of streaming potential, and that the present method is effective for water channel prospecting. 3 refs., 8 figs.

  1. Monitoring a temporal change of seismic velocity in a geothermal reservoir; Chinetsu choryuso hendo ni tomonau jishinha sokudo henka kenshutsu no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Sugihara, M; Nishi, Y; Tosha, T [Geological Survey of Japan, Tsukuba (Japan)

    1997-10-22

    Data derived at the Kakkonda geothermal area were used to discuss functions of monitoring a temporal change of seismic velocity in geothermal reservoir. The data were selected from about 50 microtremors generated in the vicinity of the area during one year in 1986. Two out of the selected microtremors were earthquakes with a magnitude of 2.7 both accompanying small precursor events. The magnitude of 2.7 may be small under normal definition, but the earthquakes are thought relatively strong because the degree of fracture adjacent to the reservoir is concentrated in a small space. This condition could be a cause of expansion of the fracture zone. The analysis was carried out according what is described by Ratdomopurbo and Poupinet. More specifically, certain time sections were taken on each certain time to fit it with the initial movement time of P-waves on two similar earthquakes, cross spectra were calculated, and phase difference in the two earthquakes was evaluated from the phase spectra. As a result, no distinct change was detected in the velocity. 5 figs.

  2. Changes in soil organisms by the application of sludge composits, and their effects. Odei taihirui no shiyo ni tomonau dojo seibutsu no henka to sono eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Niijima, K.; Fujita, K.; Ogawa, M. (Forestry and Forest Products Research Institute, Tsukuba (Japan))

    1993-08-31

    With an objective to utilize sewage sludge more effectively, composted sewage sludge has been applied to seed beds to investigate its effect on soil macrofauna and higher fungi, and its relativity with change in soil organisms, growth of young trees, and soil science. Forty-eight seedling sections, each 5 m [times] 5 m, were made on a seed bed which was applied with Tenryu sludge composts (polymer-based coagulant), several other kinds of sludge composts, fallen leaf composts, and cattle excrement composts at predetermined rates from zero to 20 kg. Each section was planted with 25 three-year-old nursery trees of a kind of oak, black pine, and cypress. As a result, the following findings were obtained: wet weight of larvae of Japanese gold beetles that attack tree roots has increased during the first and second years in the Tenryu sludge applied section, but no longer increased in the third year; the relationship between the other composts and soil macrofauna was not made clear; Scleroderma Cepa PERS, a mycorrhiza bacteria, has been generated in the oak planted section in the second, third and fourth years, with the second year particularly having generated it in a greater amount in proportion with the fertilizer application amount, but the fertilizer effect thereafter is not clear. 24 refs., 6 figs., 9 tabs.

  3. Change in pore structure of coals by activation with KOH; KOH fukatsushita sekitan no saiko kozo

    Energy Technology Data Exchange (ETDEWEB)

    Maruyama, K.; Yoshizawa, N.; Ishikawa, E.; Kobayashi, M.; Toda, Y.; Yamada, Y.; Shiraishi, M. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    Three typical Japanese coals of non-coking coal, coking coal and anthracite were heat-treated with KOH, and change in their pore structure was examined by absorption of N2, X-ray diffraction and TEM observation. In addition, the relation between a coal rank and pore structure was also studied by absorption experiment of N2. In experiment, the mixture of coal and KOH in a nickel holder was heat-treated in N2 gas flow at heating rate of 2{degree}C/min, and held at a fixed temperature for one hour. To clarify the pore structure, N2 absorption isotherms were measured at -196{degree}C under nearly 76cmHg using a commercially available full-automatic absorption measurement equipment. Based on the X-ray diffraction and TEM observation results on activated coals, the relation between the N2 absorption and pore structure was studied. The results are summarized as follows: (1) The yield and absorption ability of coals increase with a coal rank, (2) The specific surface area of coals reaches its peak at 800{degree}C in activation temperature regardless of a coal rank, and (3) The activation behavior of coals is dependent on a coal rank. 5 refs., 7 figs., 1 tab.

  4. Dissipative structure of mechanically stimulated reaction; Kikaiteki reiki hanno ni okeru san`itsu kozo

    Energy Technology Data Exchange (ETDEWEB)

    Hida, M. [Okayama Univ., Okayama (Japan). Faculty of Engineering

    1994-12-20

    Recently various studies have been conducted concerning the state changes of materials obtained through mechanical alloying (MA) or mechano-chemical (MC) processing. What is noticeable is the quasi-steady state of almost all the materials obtained through various processes including MA and MC, and that the super cooling, supersaturating and high residue distortion realized under unbalanced conditions have not been clarified. In other words, the tracing capability to the external binding conditions is low. In this report, the appearance of the high temperature phase and high pressure phase obtained through MA or MC processing, the forming of amorphous, the mesomerism of the amorphous materials, the interesting phenomena generated by combination between the mechanical disturbance and chemical reactions were discussed with concrete examples, and a steady dissipative organization theory was approached from the viewpoint of dissipative structure development which is equal to the forming process of the quasi-steady phase. 34 refs., 2 figs.

  5. Structure and reaction of electrolytic solution. Denkaishitsu yoeki no kozo to hanno

    Energy Technology Data Exchange (ETDEWEB)

    Otaki, H. (Okazaki National Research Inst., Aichi (Japan))

    1990-07-05

    An electrolytic solution has been recognized as an ion transporting system since the oldest time in the history of electrochemistry, and the chemistry related thereto forms the most basic field of electrochemistry. In this article, the progress of chemistry concerning electrolytic solutions since M. Faraday is briefly stated, and in view of very scanty structural knowledge available on other solutions in comparison with the structure of water on which extensive studies have been made, the respective structures of such non-aqueous solutions as the mixed solvent of N,N-dimethylformamide (DMF)-acetonitrile (AN) and the mixed solvent of dimethylsulfoxide (DMSO)-2,2,2-triphloroethanol (TFE) are studied. In addition, concerning the solvation when ions exist in such a non-aqueous solvent mixed system, the selective solvation of Cu {sup 2+} ions in the DMF-AN and Cu {sup 2+} as well as Cl {sup {minus}} ions in the DMSO-TFE is respectively explained, and the solvent effect, etc. of Cu {sup 2+} ions and Cl {sup {minus}} ions on the complex forming reaction are discussed. 17 refs., 8 figs., 2 tabs.

  6. Mathematical structure of ocean container transport systems; Kaiyo container yuso system no suriteki kozo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Shinkai, A [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Chikushi, Y [Nippon Telegraph and Telephone Corp., Tokyo (Japan)

    1997-10-01

    Mathematical structure of a vessel arrangement program was discussed in order to learn roles of container ships in ocean transport systems among China, NIES/ASEAN countries and Japan. Formulation is possible on a mathematical handling method for sailing route connection diagrams between ports, a transport network to indicate container movements, a service network to indicate sailing routes, and a network generalizing them. This paper describes an analysis made on the container transport system between Japan and China, taken as an example. Four ports were selected each from Japan and China, and the statistical database for fiscals 1996 and 1994 was utilized to set models for: (a) the liner network system with transshipment at the port of Shanghai and (b) the cruising route system going through the ports of Yokohama, Nagoya and Kobe. A hypothesis was set that a consortium (coordinated ship allocation) can be implemented ideally and completely. The transport network (a) is lower by 10% in total cost than the transport network (b), resulting in 1.6 times greater productivity. Actual service network is closer to the network (b), but the system can be utilized for discussing guidelines on vessel arrangement programs with which shipping companies pursue better management efficiency under a condition that the consortium can be formed. 10 refs., 6 figs., 2 tabs.

  7. Today and tomorrow on optimization of structural systems. Kozo system saitekika no genjo to shorai

    Energy Technology Data Exchange (ETDEWEB)

    1992-07-20

    It has been 30 years since a conception structurally optimized design method'' was advocated as a new structural design system which links three factors; mathematical programming, a finite element method, and computers. This paper summarizes the current states in the optimizing technologies in Japan and views over their future, with reference mainly to the two symposiums held in the past as an activity of the subcommittee for structural system optimization in the Japan Society of Civil Engineers. The summary covers the following matters: Optimizing algorithms for structural designs, fuzzy theories, practical use of expert systems and AI, maintenance and management systems for structures, vibration control, shock resistant designs, inverse problems and structure identifying problems, and designs of underground and off-shore structures. For instance, examples of bridge designs include a minimum mass design on a pedestrians' bridge incorporating vibration sensitivities into restricting conditions, comparisons of economics in suspension bridges using a multi-stage determination method, and many others. Optimizing technologies are believed to advance greatly in the future and be used as a very routine design tool. 145 refs., 1 fig., 3 tabs.

  8. Fault structure analysis by means of large deformation simulator; Daihenkei simulator ni yoru danso kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, Y.; Shi, B. [Geological Survey of Japan, Tsukuba (Japan); Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1997-05-27

    Large deformation of the crust is generated by relatively large displacement of the mediums on both sides along a fault. In the conventional finite element method, faults are dealt with by special elements which are called joint elements, but joint elements, elements microscopic in width, generate numerical instability if large shear displacement is given. Therefore, by introducing the master slave (MO) method used for contact analysis in the metal processing field, developed was a large deformation simulator for analyzing diastrophism including large displacement along the fault. Analysis examples were shown in case the upper basement and lower basement were relatively dislocated with the fault as a boundary. The bottom surface and right end boundary of the lower basement are fixed boundaries. The left end boundary of the lower basement is fixed, and to the left end boundary of the upper basement, the horizontal speed, 3{times}10{sup -7}m/s, was given. In accordance with the horizontal movement of the upper basement, the boundary surface largely deformed. Stress is almost at right angles at the boundary surface. As to the analysis of faults by the MO method, it has been used for a single simple fault, but should be spread to lots of faults in the future. 13 refs., 2 figs.

  9. Magnetic structure of Akita-Yakeyama volcano; Akita Yakeyama chiiki no jikiteki kozo

    Energy Technology Data Exchange (ETDEWEB)

    Okuma, S [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    Akita-Yakeyama is a Quaternary volcano located in the north-western part of the Sengan geothermal area. Geothermal resource surveys have been performed from the middle of the 1970s in the Sengan geothermal area, and the Sumikawa geothermal power plant started its operation in 1995. By the analysis, the magnetic basement depth became lower in the north of Yakeyama body. However, the distribution including low magnetic anomaly in the south of Yakeyama body could not be explained only by a simple magnetic structure model. In this study, the magnetic anomaly in this area was analyzed in detail, and a construction of the magnetic structure model was intended by taking borehole data into account. The low magnetic intensity zone with low amplitude agreed well with the geothermal alteration zone. The high magnetic intensity zone and the low magnetic intensity zone corresponded with the distributions of volcanic rocks magnetized normally and reversely, respectively. Kakkonda and Matsukawa geothermal power plants were located in the distinct low magnetic intensity zones. There was a low magnetic intensity zone with long wave length over the whole Sengan geothermal area. A high magnetic intensity zone was observed in the northern foot of this area. From the magnetic measurements of borehole sample rocks, this was found to correspond with the newly formed granite body. 9 refs., 4 figs.

  10. Surface structures and optical functions of living things. Seibutsu no hyomen kozo to kogaku kino

    Energy Technology Data Exchange (ETDEWEB)

    Kumazawa, K.; Takimoto, J.; Tanaka, S.; Tabata, H. (Nissan Motor Co. Ltd., Tokyo (Japan))

    1993-12-24

    This paper describes the following matters as one example of structural coloring of non-motional nature on the coloring mechanism in wings of Morpho sulkouskyi butterfly: The structure of scales on butterfly wings may be modelled into such a structure of a right angle frame of reference having a cyclic arrangement (with an interval of 0.7 [mu]m) of a zigzagged protrusion in the 'x' direction called a ridge (with a height of 1.8 [mu]m and a width of 0.54 [mu]m, the shape not changing in the 'y' direction), and having a plurality of protrusions of a ridge form called lamella in the 'z' (height) direction. A simple multi-layered thin film model was assumed that has lamella layers and air layers laminated alternately in the 'z' direction. The model was used to calculate reflection spectra on vertically incident light based on thickness and refractive index of material layers determined by a structural analysis of the scales. The result was considerably close to the reflection spectra of scales measured by using a microscopic spectrophotometer when the number of layers is set to six. The paper describes briefly examples of motility structural coloring (skin cells of rainbow color in tropical fish). 7 refs., 12 figs.

  11. Imaging of salt structure. 2; Gan`enso kozo no imaging. 2

    Energy Technology Data Exchange (ETDEWEB)

    Akama, K; Saeki, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1997-05-27

    With respect to a velocity model structuring method using depth focusing analysis (DFA) as a depth image processing technology used for elastic wave exploration, its practicability was discussed. First, synthetic data were used to extract problems in the DFA. The problems were extracted by using a model with constant velocity as an initial model, deciding on the sequential structures from the higher order, and estimating velocity and depth of each layer by using a model fitting type method. In its application to field data, characteristic records include those for rock salt beds distributed in a sheet form and the folding structure associated with the growth thereof, as acquired in offshore seismic exploration carried out in the eastern part of Gulf of Mexico. The conclusion is that the DFA is a method that can derive a velocity model with required accuracy by using a minimum number of repetition even against relatively complex structures. Particularly, the quick convergence from the initial model with a constant velocity until a certain accuracy is reached is a noteworthy advantage. 3 refs., 6 figs.

  12. High resolution resistivity profiling using STRATAGEM system; Stratagem wo mochiita kobunkainohi teiko kozo tansarei

    Energy Technology Data Exchange (ETDEWEB)

    Yamane, K; Inoue, J; Takasugi, S [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Inazaki, T [Public Works Research Institute, Tsukuba (Japan)

    1997-05-27

    A tensor type CSMT method (STRATAGEM) was introduced for the purpose of investigating shallow subsurface, and a field test has been carried out thereon. This system consists of a transmission section, and a sensor section and a data acquisition and processing section to observe waveforms in a responsive electromagnetic field. The signal source is a semi-circular air loop with a radius of a little smaller than 2 m. The measuring points were selected at locations about 200 m apart from the signal source to measure two electric field components and two magnetic field components by using sensors installed on the ground surface. The field test was performed at the Yutsubo area in Oita Prefecture, Japan. The electric field dipole is basically 5 m long, while S and E lines are 10 m long. The measurement frequency ranges from 96 kHz to 1000 kHz. The measurement time was about five minutes, and the whole measurement work including apparatus set-up and withdrawal was completed in about 15 minutes to minimize interference with the field which is a meadow. The field test result revealed that resistivity profile in shallow subsurface can be obtained much more easily than with the conventional CSMT method. 2 refs., 10 figs.

  13. Countermeasures for increasing sequence continuous casting; Renchu kinosei taikabutsu zaishitsu, kozo kaizen ni yoru renrenchusu kojosaku

    Energy Technology Data Exchange (ETDEWEB)

    Tsuda, Masato; Shinagawa, Hiroaki; Kamada, Ryuji; Hiraga, Yutaka; Hara, Takayasu [Nippon Steel Corp., Tokyo (Japan)

    1999-06-01

    In the second continuous casting line of Kure Iron Works, Nisshin Steel Co., Ltd. improvement of the continuous casting counts per tundish was attempted for a target of max. 20. The results are as follows: (1) Non-SiO{sub 2} conversion of material for the long nozzle immersed part: About 20% improvement of durability compared with a conventional material to clear 0.059 mm/min of the targeted erosion speed when 20 CCC/TD is realized, (2) Durability improvement of SN plate: About 20% durability improvement was attained compared with a conventional material by the adoption of a non-SiO{sub 2} material, (3) Erosion resistance improvement of the immersed nozzle slug line part: Castable period was extended to 1 ch life improvement by increasing zirconia content, (4) Rise of stopper full open position: The rise of the full open position produced less variation of melt level than the conventional structure without increase of the SN opening, enabling plugging prevention between the stopper head and the upper nozzle which was an objective of this improvement, (5) Structure improvement of the upper nozzle: This improvement successfully prevented leaks from damage of the casting stop nozzle metal case and enabled casting under low gas flow even in TD nozzle plugging. These improvements gave a possibility to achieve max. 20 CCC/TD. (NEDO)

  14. Coherent structure in geostrophic flow under density stratification; Mippei seisoka ni aru chikoryu no soshiki kozo

    Energy Technology Data Exchange (ETDEWEB)

    Tsujimura, S.; Iida, O.; Nagano, Y. [Nagoya Institute of Technology, Nagoya (Japan)

    1998-10-25

    The coherent structure and relevant heat transport in geostrophic flows under various density stratification has been studied by using both direct numerical simulation and rapid distortion theory. It is found that in a neutrally stratified flow under system rotation, the temperature fluctuations become very close to two-dimensional and their variation is very small in the direction parallel to the axis of rotation. Under the stable stratification, the velocity and temperature fluctuations tend to oscillate with the Brunt-Vaisala frequency. Under the unstable stratification, on the other hand, vortex columns are formed in the direction parallel to the axis of rotation. However, the generation of the elongated vortex columns cannot be predicted by the rapid distortion theory. The non-linear term is required to generate these characteristic vortex columns. 11 refs., 18 figs., 1 tab.

  15. Leading research of smart structural system; Chiteki kozo system no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The technology trend was surveyed to clarify the themes of smart structural system towards its R and D. The smart structural system is a structural system which incorporates functions of perception, judgment and learning by integrating functions, structures and information, to ensure the structural soundness at real time and control the active-adaptive of shapes. The final goal of it is to make materials and structures similar to organic systems. It has a self-repair function which can detect the generation and propagation of cracks and prevent the destruction positively with conducting self-diagnosis. High performance, high efficiency and energy saving are expected by combining the conversion of design concept into destruction control and the regulation of vibration, noise and shape. Especially, it is effective for the safety of aerospace systems, earthquake disaster measures, and extension of machine life. This report describes the background, purpose, R and D activities in Japan and foreign countries, and basic development themes. In addition, it arranges the needs of various industrial fields systematically, and proposes a concrete concept. Furthermore, the effects expected by the application of smart structural systems and the outline of international technical cooperation are presented. 110 refs., 164 figs., 19 tabs.

  16. Fatigue of cable anchorage of large cable stayed bridge; Daikibo shachokyo cable teichaku kozo no hiro

    Energy Technology Data Exchange (ETDEWEB)

    Endo, T.; Matsumoto, T. [Honshu-Shikoku Bridge Authority, Tokyo (Japan); Tsukahara, H. [Yokogawa Bridge Corp., Tokyo (Japan); Miki, C. [Tokyo Institute of Technology, Tokyo (Japan)

    1995-10-21

    Design considerations such as design schemes, the assemblage and welding of steel plates, and safety for fatigue of welded connections have to be taken for the cable anchorages of the steel cable stayed bridges. In this study, two full scale models, which have different shape of box anchorages welded to the web of the main girder, were made to investigate fatigue characteristics as well as assemblage of plate and gelding details. Finite element analyses for both test models and actual bridges here carried out to compare stress distribution. It was confirmed that the assemblage and welding of both types of box anchorage were attainable kith required quality and accuracy. According to the fatigue test, fatigue cracks originated from the weldings of the bearing plate to which the load from cable socket applied directly were caused by out-of-plane bending of the bearing plate. It was proved that the slight modifications of the details around the bearing plate resulted in sufficient fatigue strength in both types of anchorage. 1 ref., 23 figs., 2 tabs.

  17. Hybrid structure in civil engineering construction.; Doboku bun`ya ni okeru fukugo kozo.

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, S. [Yokohama National Univ. (Japan). Faculty of Engineering

    1995-03-30

    The structure of steel-concrete hybrid structure which is recently attracting attention is outlined quoting some examples. The effects of steel-concrete hybrid structure are classified according to the characteristics. The Normandie Bridge completed in January this year near the mouth of the Seine River in France is a cable stayed bridge with the world largest span, and it has a hybrid structure of ingeniously combined steel and concrete. The Dole Bridge in France is a hybrid bridge with 7 continuous spans having steel corrugated sheets in the web. Hybrid structure has come to be applied to many structures other than the superstructure works of bridges. The substructures of bridges are applied to immersed tunnels, and the usefulness has come to be recognized widely. The features of hybrid structure can contribute well to the reinforcement of existing structures. In addition, adoption of hybrid structure has been studied as the best method for repairing and reinforcing structures damaged by earthquakes. 8 refs., 6 figs., 1 tab.

  18. Fiscal 1997 survey of overseas coal import base arrangement and promotion. Effects of the expansion of coal trade by IPP on the supply/demand of general coal in Asia; 1997 nendo kaigaitan yunyu kiban seibi sokushin chosa. IPP ni yoru sekitan boeki no kakudai ga Asia no ippantan jukyu ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In consideration of the coal situation in the Asia/Pacific region, a study was made of effects of the expansion of coal trade by IPP on supply/demand of general coal in Asia. When aggregating increases in demand of general coal for electric power use in ten Asian counties, they will be an increase of 130.75 million tons in 2005 over 1997. Fifty nine percent of it is equivalent to the increase by IPP and exceeds the demand expanded by electric utilities operators. Further, a possibility is predicted of contracts and coal quality being different from until now. However, there will be a lot of cases in which plans of constructing power plants in Asia are not so developed as expected except Japan, Korea and Taiwan, and also the effect of the currency crisis starting in Thailand largely affects. In terms of the coal supply, countries which export general coal are only China and Indonesia. Indonesian coal is expanding its production and export rapidly and remarkably. The environmental control in Asia has been tightening, and the fuel selected by IPP is mainly coal rather than natural gas. 40 refs., 94 figs., 179 tabs.

  19. K arl B arth , De Zondag, Nederlandse vertaling deur W. M. van ...

    African Journals Online (AJOL)

    Test

    en geniet van die helderheid en milde humor wat orals op hierdie bladsye gevind word. In die tweede plek omdat studie van hierdie boekie die leser kan bevry van die wettiesheid wat hom so dikwels van die geeste meester maak as die sondagsviering in diskussie is. Die hele betoog is 'n getuienis van erns en vreugde.

  20. Geological structure of Osaka basin and characteristic distributions of structural damage caused by earthquake; Osaka bonchi kozo to shingai tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, K; Shiono, K; Inoue, N; Senda, S [Osaka City University, Osaka (JP. Faculty of Science); Ryoki, K [Osaka Polytechnic Collage, Osaka (Japan); Shichi, R [Nagoya University, Nagoya (Japan). Faculty of Science

    1996-05-01

    The paper investigates relations between the damage caused by the Hyogo-ken Nanbu earthquake and the deep underground structures. A characteristic of the earthquake damage distribution is that the damage concentrated near faults. Most of the damages were seen on the side of faults` relatively falling rather than right above the faults and of their slightly slanting to the seaside. Distribution like this seems to be closely related to underground structures. Therefore, a distribution map of the depth of basement granite in Osaka sedimentary basin was drawn, referring to the data on basement rock depth obtained from the distribution map of gravity anomaly and the result of the survey using the air gun reflection method. Moreover, cubic underground structures were determined by 3-D gravity analysis. The result was concluded as follows: when observing the M7 zone of the low land, in particular, where the damage was great from an aspect of gravity anomaly, the basement rock below the zone declined near the cliff toward the sea, which indicates a great possibility of its being a fault. There is a high possibility that the zone suffered mostly from the damage caused by focusing by refraction and total reflection of seismic wave rays. 3 refs., 8 figs.

  1. Velocity structure of Nojima-fault by VSP method; VSP ho ni yoru Nojima danso no sokudo kozo

    Energy Technology Data Exchange (ETDEWEB)

    Kuwahara, Y; Ito, H; Kiguchi, T; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan)

    1996-05-01

    In order to investigate in detail structures of the fractured fault band, the VSP tests were conducted using a 750m deep borehole penetrating the Nojima fault in Awaji Island. The borehole penetrates the fault clay band at a depth of 624m in the Hirabayashi area. The offset VSP survey, conducted by the aid of hydrophone through the naked borehole, detects many characteristic phenomena resulting from the fault fracture. Largely fractured lithofacies are found by the core observation at a depth in a range from 557 to 673m. P-waves propagate at 4.6 and 5.1km/s above and below the fractured band, respectively. The fractured band is subdivided into 2 sections, both being of low speed of 4.5 and 3.1km/s. The X1 and X2 phases resulting from the fault fracture are also observed, above and below the fractured band. The causes for these wave phases are now under investigation. 4 figs.

  2. Structural study of synthetic polymers by MALDI-TOFMS; MALDI-TOFMS ni yoru gosei kobunshi no kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Noguchi, K.; Hirayama, K. [Ajinomoto Co. Inc., Tokyo (Japan)

    1998-08-01

    As observation results on the time-dependent change in the ring-opening reaction of novolac epoxy resin with acetic acid by MALDI-TOFMS, the epoxy ring was opened with reaction time, the hydroxy group formed by the ring-opening reaction was acetylated, those components were measured. In the case of the FABMS/MS observation of materials and the reaction products, the estimation structure could be confirmed from the measured results of MALDI-TOFMS. In the polymerization of bisphenol A epoxy resin with N, N`-dimethylethylenediamine, it was observed by MALDI-TOFMS that many kinds of polymers with high molecular weight were formed with an increase of reaction time. In this case, the LSIMS/MS observation of materials and the reaction products was carried out, the estimation structure could be confirmed from the measured results of MALDI-TOFMS. 19 refs., 8 figs.

  3. Change of unit skeletons during an artificial coalification; Jinko sekitanka katei ni okeru tan`i kokkaku kozo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, Y.; Miki, Y.; Hayamizu, K. [National Institute of Materials and Chemical Research, Tsukuba (Japan); Okada, K. [Coal Mining Research Center, Tokyo (Japan); Suzuki, Y. [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-28

    In order to obtain knowledge about formation and growth of condensed ring structure in a coalification process, discussions were given on product skeleton structure by using hydrogenation and hydrocracking of heated cellulose. In underwater heating of cellulose, reaction of dehydration has occurred at 200{degree}C or lower, that of decarbonation at 250{degree}C or higher, and that of demethanizing at 300{degree}C, resulting in production of a dark-brown coal-like substance. The substance has lower H/C value and higher O/C value than coal. As the underwater heating temperature rises, the hydrogenation reactivity of the heated substance decreases, and so does the ratio of conversion into toluene solubles. These phenomena are related to strength of cross-linking bond between unit skeleton structures. A substance heated at an underwater heating temperature of 200{degree}C turns toluene-soluble almost completely even during the hydrogenation reaction (350{degree}C for 2 hours), but the soluble product decreases at underwater heating temperatures of 250 and 300{degree}C. However, soluble product of more than 90% was obtained when hydrocracking (at 425{degree}C for one hour) was performed. The toluene-soluble product in the heated substance is only 50% when the underwater heating temperature reaches 350{degree}C even if the hydrocracking is carried out. 3 refs., 5 figs.

  4. Studies of structure change of iron sulfates and its catalysis; Ryusantetsukei shokubai no kozo henka to sono shokubai sayo

    Energy Technology Data Exchange (ETDEWEB)

    Ogata, E.; Horie, K. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Nishijima, A. [National Institute of Materials and Chemical Research, Tsukuba (Japan)

    1996-10-28

    Since a huge amount of coal containing inorganic ash is treated for the commercial hydroliquefaction process, cheap catalysts widely distributing on the earth with large reserves are desired rather than expensive catalysts. This paper describes the effects of addition of sulfur on the catalysis of iron sulfates during the hydroconversion of 1-methylnaphthalene (1-MN). Reactions of 1-MN were conducted at the same charging amount of iron in the reaction system. Sulfur was directly added in the reaction system using ferrous sulfate (FeSO4) as precursor. Consequently, it was found that FeSO4 provides lower but similar catalytic activity to the synthetic pyrite catalyst prepared through the complex processes with the precise control. Thus, it was revealed that high performance pyrrhotite (Fe(1-x)S) catalyst can be prepared for the hydrogenation of aromatic-rings by adding solid sulfur into the reaction system using commercial reagent, FeSO4 as a precursor of the catalyst. 9 figs.

  5. Coal Liquefaction characteristics and chemical structure of product oil; Sekitan ekika hanno tokusei to seiseibutsu no kagaku kozo

    Energy Technology Data Exchange (ETDEWEB)

    Endo, H.; Sato, M.; Chiba, T.; Hattori, H. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Sasaki, M. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    Through the hydrogenolysis of Wandoan coal and Tanito Harum coal which are used for the NEDOL process, differences of liquefaction characteristics between them were found. The purpose of this study is to grasp these differences as differences of chemical structures of oil fractions. The compound type analysis was conducted for oil fractions obtained at varied reaction temperature for varied reaction time. Coal liquefaction characteristics of these coals were discussed by relating oil yields and chemical structures. For Tanito Harum coal, yields of gas and oil were considered to be lower than those for Wandoan coal, which reflected that the contents of partially hydrogenated hydroaromatics in oil fraction from the former were lower than those from the latter, and that the remarkable change of composition did not occur with the progress of the reaction. For both the coals, the remarkable changes in the average molecular weight of oil fraction were not observed with the progress of the reaction. While, the content of methane gradually increased with the progress of the reaction, which suggested that oil was gradually dealkylated. 5 figs.

  6. Report on the FY 1999 basic research on intelligent structure; 1999 nendo kozo chinoka no kiso kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A concept of a system is constructed in which a series of the flow from the construction of structures to the shape and control in structural phase, repair, and dismantlement is made effective and controllable by giving a function of intelligent structure to structural systems in aerospace/architecture/civil engineering fields. For it, fundamental technologies required for the systems were extracted for construction of the technology system. Further, in relation to the intelligent machinery system including the control method, manipulation, and communication of the structure under the micro-gravity environment required for this system, the basic experiment was conducted at the ground gravity-free experimental center to acquire the effective data. As to the base technology, three fields were studied of the intelligent machinery system including the behavior/control of materials and structure, intelligent robot, and communication. In the experiment on micro-gravity environment, experiments were carried out on the behavior of micro-gravity rover for small planetary probe, inter-satellite group communication, capture of trouble-satellite, development of inflatable structure, and hopping robot. The valuable data were obtained. (NEDO)

  7. Structure of non-equilibrium seeded plasma excited with microwave; Micro ha reiki hiheiko seed plasma no kozo

    Energy Technology Data Exchange (ETDEWEB)

    Miyakawa, M.; Murakami, T.; Suekane, T.; Okuno, Y.; Kabashima, S. [Tokyo Institute of Technology, Tokyo (Japan)

    1996-10-20

    Structure of non-equilibrium cesium seeded argon plasma excited with microwave power is simulated numerically. The plasmas produced at suitable microwave powers are found to consist of three regimes, that is, the region limited by charged particle loss toward the wall, the full seed ionization and the diffusion limited regions. The fully ionized seed plasma is produced within the skin-depth determined by the electrical conductivity of the plasma, and the thickness of the fully ionized seed plasma depends on the seed fractions gas pressure and microwave power. 15 refs., 6 figs.

  8. Geometrical relaxation of excitations in one-dimensional conjugated polymers; Giichijigen kyoeki kobunshi reiki jotai no shusa kozo kanwa

    Energy Technology Data Exchange (ETDEWEB)

    Yoshizawa, M. [Tohoku University, Sendai (Japan). Faculty of Engineering

    1995-12-15

    Large ultrafast optical nonlinearities in conjugated polymers have attracted much attention because of possible applications to nonlinear optical devices. One-dimensional systems such as conjugated polymers have localized excited states with geometrical relaxation. In this study, photoexcited states in polydiacetylene has been investigated by femtosecond Raman gain spectroscopy with 300-fs resolution. A new photoinduced Raman peak with lifetime of 1.5 ps has been observed at 1200cm{sup -1} for the first time. This peak indicates acetylene-like structure of the main chain relaxes to butatriene-like structure due to the formation of self-trapped exciting with the geometrical relaxation. The formation and decay kinetics of the Raman signals is consistent with the relaxation processes of exciting observed by femtosecond absorption spectroscopy. 8 refs., 5 figs.

  9. Adaptation of topology optimization on truck-structure; Kinshitsukaho ni yoru iso saitekika shuho no truck kozo eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Tachibana, H; Kojima, A; Chiba, S [Mitsubishi Motors Corp., Tokyo (Japan)

    1997-10-01

    An optimization using the homogenization method has been applied to a truck-structure on the concept design stage. A truck-structure is grouped into 3 classes (thin plate structure , thick plate structure and solid structure), then example, effectiveness and method for the application for the purpose of weight reduction , high rigidity and high eigen-frequency are introduced. 3 refs., 24 figs., 1 tab.

  10. Structure analysis of ultra-thin films. STM/AFM. Chousumaku no kozo kaiseki. STM/AFM

    Energy Technology Data Exchange (ETDEWEB)

    Nozoe, H; Yumura, M [National Institute of Materials and Chemical Research, Tsukuba (Japan)

    1994-03-30

    Fullerene (C60) and carbon nanotubes are expected as new carbon structures. This article describes the observation results of C60 and carbon nanotubes by means of STM (scanning tunnel microscope). The STM images of C60 thin films are illustrated, which have been obtained by annealing at 290 centigrade. It was confirmed that C60 monomolecular thin films are formed which conform to the substrate and have high regularity. The step height of C60 monomolecular thin films coincided with the step height of Cu (111) plane, which suggested that the step of films is reflected in that of Cu substrate. For the STM images under bias voltages, various images of C60 with three-fold axis of symmetry were observed. On the other hand, from STM observation of carbon nanotubes with diameter of about 30 nm which were separated and purified from the cathode deposits during the preparation process of C60, it was found that they have concentric multilayer structure. 18 refs., 7 figs.

  11. Structural analyses of very large semi-submersibles in waves; Choogata hansensuishiki futai no harochu kozo oto kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Iijima, K.; Yoshida, K.; Suzuki, H. [The University of Tokyo, Tokyo (Japan)

    1997-08-01

    An analysis method in which the technique of a vehicle obtained when a three-dimensional singular point distribution method and Kagemoto`s mutual interaction theory are combined was expanded for the fluid area was proposed as the structural analysis of very large semi-submersibles in waves. A partial structure method is used for the structure. In a fluid area, the number of unknown quantities appearing in a final expression could be largely reduced by introducing the new concept of a group body. In this process, both hydro-elasticity and hydrodynamic mutual interaction are considered. As a result, floating bodies that could not be previously calculated can be modeled as a three-dimensional frame structure and the response analysis in waves can be carried out without damaging the accuracy. The calculation result is used as the input data required for analyzing the structural fatigue locally during structural design of very large semi-submersibles in the 3,000 (m) class. This study can present a series of procedures between the response analysis of very large floating bodies in waves and the structural design. 11 refs., 14 figs., 1 tab.

  12. Structural changes in deashed coals induced by heat treatment; Kanetsu shori ni yoru dakkaitan no kozo henka

    Energy Technology Data Exchange (ETDEWEB)

    Sugano, M.; Sekita, M.; Muramatsu, Y.; Mashimo, K.; Wainai, T. [Nihon University, Tokyo (Japan). College of Science and Technology

    1996-10-28

    Change in structures of 3 kinds of coals with different coal ranks and their deashed coals was studied by heat treatment below 200{degree}C. In experiment, crushed Adaro, Taiheiyo and Huaibei coals below 200mesh and their deashed coals were used as specimens. The coal and deashed coal specimens dried in vacuum at 110{degree}C for 3 hours were filled into an autoclave, and the heat-treated coal specimens were prepared by holding them under initial nitrogen pressure of 2kg/cm{sup 2} at a fixed temperature for 30min. Extraction using pyridine as solvent, volumetric swelling using methanol or benzene as solvent, and measurement of the amount of carboxyl and phenolic hydroxyl functional groups were conducted for these coal specimens. The experimental results are as follows. Huaibei coal has developed aromatic ring structure, and its structure is hardly affected by heat treatment. The oxygen containing functional groups decrease by heat treatment over 100{degree}C in Adaro coal and 150{degree}C in Taiheiyo coal, and PS, MQ and BQ also decrease due to aggregation between molecules. 5 refs., 2 figs.

  13. Study on spontaneous potential exploration considering resistivity structures; Hiteiko kozo wo koryoshita shizen den`iho tansa

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H; Sakurai, K; Shimada, H [OYO Corp., Tokyo (Japan)

    1996-10-01

    Spontaneous potential (SP) was measured on the known traverse line of resistivity structure crossing Hanaori fault in Ohara area, Kyoto city to observe change in SP around the fault and to examine the possibility of fault position exploration. The supposed causes of generation of SP are as follows: the existence of sulfide mineral deposit including polarized minerals, underground fluid flow, and the existence of stratum including chemical compositions from hot springs. The SP method estimates underground structures based on measured surface potential distributions using DC component under anomaly of SP. FEM modeling clarified that a fault fracture zone is one of the causes of generation of SP, by considering SP measurement and resistivity structure strongly affecting observed SP. Consequently, combination of SP measurement with resistivity structure exploration allows a reliable fault estimation method. Under the assumption that anomaly of SP is caused by polarization around fault, the horizontal dipole model based on polarization of current source dipole along fault can well explain the measured data. 2 refs., 6 figs.

  14. Three-dimensional analysis of the magnetic structure in Hokkaido, Japan; Hokkaido no sanjigen jiki kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Makino, M [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    The magnetic structure in Hokkaido was quantitatively analyzed by the magnetic anomaly distribution. This paper describes its characteristics. Detection of structural boundaries and 3-D analysis of double-layer structure were conducted for the regional magnetic data in a region with about 500 km square. There was not so large difference in patterns of magnetic anomaly distribution between the case that the direction of magnetization was set at 45{degree} to the west during the geomagnetic conversion according to Segawa and Oshima and the case that it was set as same as the current geomagnetic direction. The method of Blakely and Simpson was useful to detect the boundaries of magnetic structures. The structural boundaries obtained were more linear than the iso-magnetic contour lines. A new method has been conceived in which the approximation of 3-D magnetic structure analysis can be deduced, and the irregularity of magnetic basement can be determined by the repeated calculation. In practice, this method was applied to the magnetic data in the whole Hokkaido. The calculation was stably converged. It was found that the magnetic structure obtained in the Kamuikotan/Ishikari-Kitakami magnetic belt exhibited a fault structure having steep slopes accompanied by the basin structure in the western boundaries. 19 refs., 6 figs.

  15. Resistivity structures imaging using time-domain electromagnetic data; TDEM ho ni yoru chika hiteiko kozo no imaging

    Energy Technology Data Exchange (ETDEWEB)

    Noguchi, K [Waseda University, Tokyo (Japan). School of Science and Engineering; Endo, M [Waseda University, Tokyo (Japan)

    1996-10-01

    The kernel function for transient vertical magnetic dipole was defined for semi-infinite uniform medium, and the 1-D imaging algorithm by TDEM (time-domain electromagnetic) method was developed for underground resistivity structure. Electromagnetic migration method directly images sectional resistivity profiles from the data observed by frequency-domain MT method, and determines underground resistivity profiles by integral equation of MT field using the concept of return travel time in reflection seismic exploration. The method reported in this paper is also one of the EM migration methods. The imaging algorithm of 2-D resistivity structure was developed by correcting 1-D imaging in consideration of the effect of 2-D anomaly on 1-D imaging (the resistivity of anomaly can be obtained from the resistivity contrast between anomaly and medium). The conventional methods require enormous forward computation, while this method can obtain underground resistivity structure in extremely short computation time, resulting in superior practicability. 12 refs., 7 figs.

  16. Deep sedimentary structure model beneath the Osaka plain; Osaka heiya ni okeru shinbu chika kozo no model ka

    Energy Technology Data Exchange (ETDEWEB)

    Miyakoshi, K; Kagawa, T; Echigo, T [Osaka Soil Test, Osaka (Japan)

    1997-05-27

    Restructuring was carried out on a sedimentary basin structure model of the Osaka plain including Osaka Bay by using newly obtained underground structural data. After the Hygoken-nanbu Earthquake of 1995, a large number of underground structure investigations have been performed in Osaka Bay and urban areas of Kobe and Osaka. However, very few surveys have been done in areas peripheral to Osaka Prefecture, such as the Ikoma area. Therefore, an attempt has been made to increase the number of measuring points to acquire underground structural data of these areas. Estimation of basic rock depths has utilized the dominant cycles in H/V spectra obtained from micro vibration survey, and good correlation of the base rock depths derived by a refraction exploration and a deep-bed boring investigation. With regard to bed division and P- and S- wave velocities in sedimentary beds in the Osaka sedimentary basin, an underground structure model was prepared, which was divided into four beds according to the refraction exploration and the micro vibration investigation. Data obtained by using this model agreed well with depth data acquired from physical exploration and other types of investigations. However, no good agreement was recognized in the data for such areas where the basic depth changes abruptly as the Rokko fault and the Osaka bay fault. 6 refs., 8 figs., 2 tabs.

  17. Structure of poly (. beta. -alanine) polymerized in the solid state. Koso jugo shita. beta. -alanine no kozo

    Energy Technology Data Exchange (ETDEWEB)

    Sakabe, Hiroshi; Nakamura, Hiroyoshi; Kimura, Hirokazu; Konishi, Takashi [Kyoto Inst. of Tech., Kyoto (Japan). Faculty of Textile Science

    1989-12-05

    The structure of poly({beta}-alanine) polymerized in the solid state was studied. This polymerization was carried out on a single crystal of {beta}-alanine at 170 centigrade for 40 h in an evacuated tube. The crystal structure of the polymer was assigned to I-type crystal of Nylon 3. The polymer chains were oriented vertical to the crystal side and different to monomer crystal orientation. This may be caused by the molecular layer slipping along the cleavage plane of monomer crystal. A scanning electron microscope(SEM) showed the band structure of hundreds nm width of same orientation, but X ray showed only unoriented rings, so that they are estimated to be the structure of fine fibril like assembly or necklace like continuous chain structure of grains. Near the surface, whiskers which were thought to be oligomer of low degree of polymerization, were observed. The SEM of end view of the etched surface did not show the laminated structure but showed the network structure of about 1 mu-m which is thought to be fibril precursor. 12 refs., 10 figs.

  18. Evaluation on lifetime risk in reinforced concrete structure; RC kozo no lifetime risk no hyoka ni kansuru kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, M. [Public Works Research Institute, Tsukuba (Japan); Adachi, H. [Taisei Corp., Tokyo (Japan); Akakura, Y. [Ministry of Transport, Tokyo (Japan); Ibayashi, K.; Ozaka, Y. [Tohoku Gakuin Univ., Sendai (Japan)

    1996-02-15

    To evaluate the risk during longevity of reinforced concrete structure subjected to earthquake motions, called lifetime risk, damage and safety were estimated by means of the earthquake risk analysis and earthquake response analysis. For the earthquake risk analysis, historical earthquake data with relatively low accuracy were efficiently taken into account, to determine the annual mean generation probability against the earthquake motion strength in ten main cities. A new damage index with load hysteresis was defined as an anti-earthquake evaluation index where accumulative damage is taken into consideration. Assuming that the damage transits from `certain state` to `certain state` every time the earthquake motion generates at the noticeable place, damage transition matrix expressing transition probability was calculated by using the results of earthquake risk analysis and the accumulative damage index. The lifetime risk was calculated from the damage transition matrix and the earthquake motion generation probability, to evaluate the safety. 21 refs., 10 figs., 8 tabs.

  19. Development of simulator for studying formation process of crustal structure. 1; Chikaku kozo keisei simulator no kaihatsu. 1

    Energy Technology Data Exchange (ETDEWEB)

    Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Murakami, Y.; Okubo, Y.; Matsubayashi, O.; Tanaka, A.; Nakajima, Y.; Morijiri, R. [Geological Survey of Japan, Tsukuba (Japan); Rokugawa, S. [The University of Tokyo, Tokyo (Japan)

    1997-05-27

    The purpose of this study is to combine seismic activity and volcanic activity by reproducing the formation process of the crustal structure from a physical viewpoint or developing as its extension a numerical simulator which can predict the future. The phenomenon to which attention is especially paid at present is a relation between the dynamic process and the thermal process in the domain including the crust or the upper mantle. Namely, to elucidate the formation process of the crust structure, diastrophism also including seismic activity, igneous activity, etc., it is important to evaluate effects of the behavior of heat supplied from the deep on the dynamic process. In the finite element method, it is not easy to make the effect of gravity reflect to the calculation for boundary conditions. Accordingly, it is general to pay attention to stress difference, considering that stress by gravity is in proportion to static rock pressure stress. Further, to realize interaction between the thermal process and the dynamic process, effects of thermal stress are expressed combining the heat conducting analysis and the plastic flow analysis. 3 refs., 7 figs.

  20. Georesistivity structure in the central part of North-Eastern Japan Arc; Tohoku chiho chubu chiiki no denki dendodo kozo

    Energy Technology Data Exchange (ETDEWEB)

    Fujinawa, Y. [National Research Institute for Disaster Prevention, Tsukuba (Japan); Kawakami, N. [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Ueshima, M. [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute; Honkura, Y. [Tokyo Institute of Technology, Tokyo (Japan)

    1998-03-13

    MT measurement of transects was made in the central part of North-Eastern Japan Arc to clarify tectonics of subduction zones. 1-D, 2-D and 3-D resistivity structures are observed in surface layers, and zones shallower and deeper than a Conrad surface, respectively. A main structure direction is S-N or NNE-SSW. Ishinomaki-Chokai tectonic line and low- resistivity zones due to Quaternary volcanos (Naruko, Onikobe) exist in a backbone range region. Resistivity is 100{Omega}{center_dot}m or less by Bostick Inversion except Mesozoic and Palaeozoic layers in the southern Kitakami mountainous region, resulting in a good agreement with previous results in a north transect. Resistivity is several {Omega}{center_dot}m and depth is several km around Shinjo basin and in surface layers of Kitakami River region. The backbone range region shows complex resistivity structures because of volcanic activity and wide-area hot water activity. High-resistivity layers correspond to stable Mesozoic and Palaeozoic land layers. Seismic velocity increases in the low-resistivity zone. Earthquake generally occurs at the boundary between resistivity structures. 68 refs., 9 figs., 2 tabs.

  1. Deep geological strucure of a volcano verified by seismic wave. Jishinha de mita kazan no shinbu kozo

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, A. (Tohoku University, Sendai (Japan). Faculty of Science)

    1991-09-01

    Three dimensional structure of seismic wave velocity for the crest and upper mantle under the North East Japan is determined by the seismic tomography which is prepared by the natural earthquakes confirmed by the observation network for micro earthquakes, indicating that the low velocity region exists just under the corresponding volcano to the upper mantle. Further, the following contents can be verified: Any micro earthquakes which are verified by the above observation network and occur at the depth of 25-40km show the lower generation rate less than 1% and the low dominant frequency compared with the conventional inland earthquake(lower limit of depth is 15km) in the same region and occur around volcanos. The existence of the remarkable reflection surface for S wave which is found at the depth of 10-20km seems to be caused by the melting mass. The above mentioned low velocity region is estimated to correspond to the lifting region of high temperature magma, micro earthquakes of low frequency to the magma activity around that magma and the reflection surface for S wave to the part of the magma. 8 refs., 4 figs.

  2. Study on the structural characteristics of extradosed concrete bridges; Ekusutoradozudo kyo no kozo tokusei ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Oka, Y. [Japan Highway Public Corp., Tokyo (Japan); Kasuga, A. [Sumitomo Construction Co. Ltd., Tokyo (Japan); Yamazaki, J. [Nihon Univ., Tokyo (Japan). Coll. of Science and Engineering

    1997-03-31

    Parameters are analyzed to provide data for deciding, in the planning and designing stages, whether a cable stayed bridge or an extradosed bridge should be adopted. Comparative investigation of the vibration properties of both types of bridges is also referred to. The result of the study on the structural properties of the cable stayed road bridge and the extradosed road bridge is introduced. Based on the concept of the extradosed bridge, designers are now able to select without restraint the after load sharing rate of the diagonal members. Parameter analysis of a diagonal member reinforced 3-span continuous beam is performed. By introducing indices showing the load sharing rate of the diagonal member, the cable stayed bridge can be distinguished logically from the extradosed bridge in designing. It is found important that the height of the main tower is set to approximately 10% the length of the center span for the construction of the extradosed bridge. The vibration properties of the cable stayed bridge and the extradosed bridge of the same scale are compared. 7 refs., 18 figs., 6 tabs.

  3. Consideration on the dynamic behavior and the structural design of large scale floating structure. 2nd Report. Stability of elastic structure and design of elastic response; Choogata futai no kozo kyodo oyobi kozo sekkei ni kansuru kosatsu. 2. Dansei henkei wo koryoshita fukugensei oyobi kozo oto no sekkei

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H.; Yoshida, K. [The University of Tokyo, Tokyo (Japan)

    1996-12-31

    A policy of improving a very large floating body was planned based on its dynamic characteristics, and a proposal was made thereon. Furthermore, discussions were given on stability that considers effect of elastic deformation required when a structure is mounted on a floating body. With respect to a structural design of a very large floating body in which elastic response is governing, and upon modeling the very large floating body into an aeolotropic plate on an elastic supporting floor, it was shown that the existing range of natural vibration speed in the elastic response is in higher range than the natural vibration speed of heave. It was also indicated that the peak height of response to waves in resonance is inversely proportional to wave frequency, and furthermore, degree of flowing in of vibration energy during the resonance is determined by an inner product of spatial vibration patterns of wave force and the excited mode shape. A proposal was made on a floating body improved of excessive response in the floating body edges by changing the characteristics of the floating body edges. In addition, discussions were given on stability that considers elastic deformation of a floating body that becomes necessary when a structure, such as a building, is built on a very large floating body. 9 refs., 9 figs., 3 tabs.

  4. Consideration on the dynamic behavior and the structural design of large scale floating structure. 2nd Report. Stability of elastic structure and design of elastic response; Choogata futai no kozo kyodo oyobi kozo sekkei ni kansuru kosatsu. 2. Dansei henkei wo koryoshita fukugensei oyobi kozo oto no sekkei

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H; Yoshida, K [The University of Tokyo, Tokyo (Japan)

    1997-12-31

    A policy of improving a very large floating body was planned based on its dynamic characteristics, and a proposal was made thereon. Furthermore, discussions were given on stability that considers effect of elastic deformation required when a structure is mounted on a floating body. With respect to a structural design of a very large floating body in which elastic response is governing, and upon modeling the very large floating body into an aeolotropic plate on an elastic supporting floor, it was shown that the existing range of natural vibration speed in the elastic response is in higher range than the natural vibration speed of heave. It was also indicated that the peak height of response to waves in resonance is inversely proportional to wave frequency, and furthermore, degree of flowing in of vibration energy during the resonance is determined by an inner product of spatial vibration patterns of wave force and the excited mode shape. A proposal was made on a floating body improved of excessive response in the floating body edges by changing the characteristics of the floating body edges. In addition, discussions were given on stability that considers elastic deformation of a floating body that becomes necessary when a structure, such as a building, is built on a very large floating body. 9 refs., 9 figs., 3 tabs.

  5. Quantum analysis in the transition process to excited state of an oxygen molecule induced by electron collisions; Denshi shototsu ni tomonau sanso bunshi ni okeru reiki jotai sen`i no ryoshironteki kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Ishimaru, K. [Gifu National College of Technology, Gifu (Japan); Okazaki, K. [Tokyo Inst. of Technology, Tokyo (Japan)

    1996-06-25

    For understanding of fundamental chemical reactions under a highly non equilibrium condition which is quite often used in plasma processing, the relevant atomic and molecular processes must be clarified. In this study, an analysis of the transition process to the excited state of an oxygen molecule induced by electron collisions in the oxygen plasma has been carried out. First, the electron density distribution in an oxygen molecule has been calculated using the extended Huckel molecular orbital method. Then, the electron potential energy distribution in the transition process to the excited state has been estimated. The electron behavior has been calculated using the estimated unidimensional electron potential energy distribution and unsteady quantum mechanics. As a result, the transition process to the excited state of an oxygen molecule induced by electron collisions and its conditions have been clarified qualitatively. 9 refs., 9 figs.

  6. Measurement of cooling coil film heat transfer coefficient with polymer reaction proceeding in a stirred batch reactor; Jugo sonai ni okeru hanno shinko ni tomonau reikyaku coil no kyomaku netsudentatsu keisu no keiji henka

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, K [Soken Chemical and Engineering Co. Ltd., Saitama (Japan); Nishi, K; Kaminoyama, M; Kamiwano, M [Yokohama National University, Yokohama (Japan). Faculty of Engineering

    1996-09-10

    In radical additional solution polymerization, the viscosity increases with reaction progress. It is important to evaluate beforehand the cooling capacity of the reactor, which worsens with the process. In this study, a stirred batch reactor with both a paddle and a helical screw impeller were studied, and measurements were made for the dynamic changes of the film heat transfer coefficient of the cooling coil with progress of the polymer reaction. We found the change could be evaluated by the calculating heat balance of the generated heat, the viscous dissipation energy and the sensible heat change under conditions of monomer conversion and changing viscosity. 11 refs., 7 figs.

  7. Change of the equivalent circuit constants accompanied by the degradation and recovery of efficiency on a-Si solar cells; A-Si taiyo denchi no koritsu no rekka to kaifuku ni tomonau toka kairo teisu no henka

    Energy Technology Data Exchange (ETDEWEB)

    Takahisa, K; Kojima, T; Nakamura, K; Koyanagi, T; Yanagisawa, T [Electrotechnical Laboratory, Tsukuba (Japan)

    1997-11-25

    Investigations were given on how the equivalent circuit constants change when efficiency of amorphous silicon solar cells changes with time in light degradation and temperature recovery. In the experiment, light irradiation tests under a constant temperature and light intensity condition, followed by recovery tests under a constant temperature and constant weak light intensity or constant temperature condition were repeated continuously. According to the result of an experiment on single layer type cells, the change in each equivalent circuit constant in association with degradation in efficiency and file factor and variation in recovery is reversible mostly. However, a slightly irreversible component was recognized only in the initial degradation process in series resistance and diode factor values. With regard to stacked cells, it was suggested that the main players to determine cell characteristics during the processes of deterioration and recovery take turns among the three layers as follows: the shape of the time-based change in the efficiency comes different and is not saturating; as the efficiency decreases, the extent of the change increases in the diode factor and series resistance; and the path the deterioration takes differs from that the recovery takes. 2 refs., 12 figs.

  8. Changes of the temperature coefficients of the characteristics which accompany degradation and recovery of a-Si solar cells; A-Si taiyo denchi no hikari (denryu) rekka oyobi kaifuku ni tomonau tokusei ondo keisu no henka

    Energy Technology Data Exchange (ETDEWEB)

    Yanagisawa, T; Koyanagi, T; Nakamura, K; Takahisa, K; Kojima, T [electrotechnical Laboratory, Tsukuba (Japan)

    1996-10-27

    Pursuant to the measuring of temperature dependency of the characteristics such as conversion efficiency, during the process of degradation in a-Si solar cells due to light and electric current and the process of recovery by annealing, this paper describes changes in temperature coefficients, correlation between the characteristic parameters and the degradation, and the results of the examination of their characteristics. The conversion efficiency {mu} degraded approximately by 45% of the initial value each by the irradiation under a light intensity with 3 SUN accelerated and by the infusion of current at 20mA/cm{sup 2}; and then, the efficiency recovered to 70-75% of the degradation by subsequent annealing. In addition, in the temperature dependency at 80{degree}C against at 20{degree}C, Isc slightly increased while Vcc greatly decreased. This slight increase in Isc was mainly due to the decrease in the width of the forbidden band, while the decrease in Vcc was due to the increase in the reverse saturation current. The temperature dependency of {mu}N was negative, becoming small in accordance with the degradation. The temperature dependency of FF/FFO was negative initially both in light and current, but it decreased with the degradation and turned to positive. The temperature coefficients of I-V parameters reversibly changed corresponding to the degradation and recovery of these parameters and stayed in a good correlation. 7 refs., 8 figs., 1 tab.

  9. Outline of tectonic geology of the cenozoic Pacific volcanic zone concerned with geothermal areas in the central America; Chubei ni okeru chinetsutai wo tomonau shinseidai Taiheiyo kazantai no chishitsu gaisetsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamasaki, T [Kyushu University, Fukuoka (Japan); Matsumoto, Y [Yamaguchi University, Yamaguchi (Japan)

    1994-09-16

    For the purpose of technological cooperation on geothermal development, investigations and discussions have been given on the geological background in the geothermal areas in Central America where the Pacific volcanic zone stretches. The geology in Central America is divided largely into three geological structures distributed in a band form in the east-west direction. Among these structure, the Pacific Volcanic Province is a Caenozoic volcanic area ranging along the Pacific Ocean coast in the south-east direction, where young and active Quarternary volcanoes are lined straight over a distance of 1,400 km. The geological structure is such that continuously traceable rift valley or pit structure agrees with the array of volcanoes. The long and wide rift valley that governs this volcanic activity forms the base of the geothermal areas dotted in the above structure. Guatemala had been proceeding with a 24-MW power plant plan in Zunil, the most important point, but the construction has been delayed because of a landslide that caused impediment to the productive wells. The plant completion is now scheduled for 1995. El Salvador is the most advanced country in geothermal power generation, which operates three plants in the Ahuachapa geothermal area, with the output reaching 95 MW. The geothermal condition per production well is 110 tons per hour at 250{degree}C. Nicaragua had been successful in generating power of 70 KW with two plants in Momtombo by 1989. 22 refs., 8 figs., 4 tabs.

  10. Micropropagation of five species of Campanula growing on the territory of Botanical Garden named prof. B.M. Kozo-Polyansky of Voronezh State University

    Directory of Open Access Journals (Sweden)

    O. A. Zemlyanukhina

    2016-01-01

    Full Text Available The development of evidence-based methods of reproduction of protected and highly decorative species that are in high demand for use in landscaping, as well as the establishment of gene pools of species and varieties of plants in actively growing collection corresponds to the main direction of the state coordination program for the development of biotechnology in the Russian Federation until 2020 «BIO 2020». The on-standing research developed and optimized the conditions for obtaining actively proliferating cultures of 5 disappearing species; Campanula rotundifolia L., Campanula persicifolia L., Campanula trachelium L., Campanula rapunculoides L., Campanula glomerata L. Optimized conditions of rhizogenesis. The effect of the different sterilization and antibiotics concentration (kanamycin, benzyl penicillin, gentamicin, klaforan on the growth and development of adventitious plants has been studied. Solutions of antibiotics for sterilization in addition to chlorine-containing agent («Belizna» and mercury (thimerosal are needed. The possible negative effects of the addition of antibiotics in incubation solution lead to increasing of somaclonal variation, neсrosis, disturbance of chlorine synthesis («fatal lack of chlorophyll», slow down the growth of adventitious shoots, and others. It is proposed LED lighting culture in a rack 16 hour period lighting LED strip 12 V power 4.5 W/m (3 LED 10 cm tape, general illumination of 2500–3000 lux. Each shelf is added with red tape photodiodes. The results allow, if necessary, to obtain plantation quantity of these kinds of Campanula in a short time.

  11. 2D resistivity survey in complex geological structure area. Application to the volcanic area; Fukuzatsuna chishitsu kozo chiiki ni okeru hiteiko nijigen tansa. Kazangan chiiki deno tekiorei

    Energy Technology Data Exchange (ETDEWEB)

    Asakawa, S; Ikuma, T; Tanifuji, R [DIA Consultants Co. Ltd., Tokyo (Japan)

    1996-05-01

    Introduced herein is an application of 2D resistivity survey to a volcanic rock area where the survey result is difficult to interpret because of its complex geological structure. In a dam site survey, main problems involve the permeability of water through faults and weathered, altered zones. At this site, a 2D resistivity survey was conducted, a 2D geological structure was deduced from the resistivity section, and the result was examined. It was found that resistivity distribution was closely related to hydrographic factors, but no obvious correlation was detected between rock classes and R, Q, and D. In conducting investigations into a section planned for a highway tunnel, it was learned that the problem was a volcanic ash layer to collapse instantly upon absorbing water, and the distribution of the ash layer, not to be disclosed by boring, was subjected to a 2D resistivity survey. The survey was conducted into the structure above where the tunnel would run, and further into the face, and studies were made about what layer was reflected by the resistivity distribution obtained by analysis. The result of the analysis agreed with the details of the layer that was disclosed afterward. 4 figs., 1 tab.

  12. Travel time and ray path computation in 2D-heterogeneous structures; Fukinshitsu kozo ni okeru jishinha soji oyobi hasen no atarashii keisan hoho

    Energy Technology Data Exchange (ETDEWEB)

    Fujie, G; Kasahara, J; Sato, T; Mochizuki, K [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1996-05-01

    Methods were studied for determining the initial travel time and ray paths with stability when an non-linear travel time inversion is performed in an inhomogeneous structure. The travel time calculation was based on Faria and Stoffa`s method. First, the 2-dimension space was sectioned by grids, and `slowness` was assigned to all the lattice points. Starting from the vibration source, travel time at each lattice point is sequentially calculated. This method calculates travel time for any structure without breakup. In this study, an algorithm more sophisticated than the method of Faria, et al., was developed, and the improvement of travel time calculation accuracy led to the accurate determination of the direction of incidence into the lattice points during the initial motion. The calculation of ray paths was effected by tracing back from the receiving points the incidence into the lattice points or by following back the ray paths to the vibration source. This method performs stable calculation for a heavily inhomogeneous structure and, with the algorithm being simple, do the parallel programming as well. 1 ref., 6 figs., 1 tab.

  13. Subsurface interpretation based on geophysical data set using geothermal database system `GEOBASE`; Chinetsu database system `GEOBASE` wo riyoshita Kakkonda chinetsu chiiki no chika kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Osato, K; Sato, T; Miura, Y; Yamane, K [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Doi, N [Japan Metals and Chemicals Co. Ltd., Tokyo (Japan); Uchida, T [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1996-05-01

    This paper reports application of a geothermal database system (GEOBASE) to analyzing subsurface structure in the Kakkonda geothermal area. Registered into the GEOBASE to analyze specific resistance structure in this area were depth information (well track and electric logging of existing wells), three-dimensional discretization data (two-dimensional analysis cross section using the MT method and distribution of micro-earthquake epicenters), and two-dimensional discretization data (altitude, and depth to top of the Kakkonda granite). The GEOBASE is capable of three-dimensional interpolation and three-dimensional indication respectively on the three-dimensional discretization data and the depth information table. The paper presents a depth compiling plan drawing for 2000 m below sea level and an SE-NE cross section compiling cross sectional drawing. The paper also indicates that the three-dimensional interpolation function of the GEOBASE renders comparison of spatial data capable of being done freely and quickly, thereby exhibiting power in the comprehensive analysis of this kind. 3 refs., 8 figs., 2 tabs.

  14. Relationship between herbicide's fate of the river flowing into lake Teganuma and its molecular structure. Teganuma ryunyu kasen ni okeru josozai no dotai to bunshi kozo no kankei

    Energy Technology Data Exchange (ETDEWEB)

    Tamura, J [Nishi Tokyo University, Yamanashi (Japan). Faculty of Science and Engineering; Ogura, N [Tokyo University o Agriculture and Technology, Tokyo (Japan). Faculty of Agriculture

    1994-04-10

    Environmental profiles of agricultural chemicals in a river flowing into Lake Teganuma were surveyed. Their dissolution and adsorption were investigated by using indoor experiments, and their behaviors were discussed from a viewpoint of molecular structure in the compounds. The herbicides detected in the river contained CNP and Benthiocarb were at high concentration at the time of spraying, but decreased sharply thereafter. The CNP had lower concentration than Benthiocarb in the river, indicating little amount flowing out from paddy fields. These differences in the environmental profiles should be attributable to natures of the herbicides. An indoor experiment has revealed that Benthiocarb has lower solubility and higher absorption strength than CNP. It was found with respect to the chemical structures that polarity increases if hetero atoms and hydrophilic substituents exist in moleculars; the solubility of Benthiocarb grows higher than that of hydrocarbons; and adsorption power relates to the area of contact with absorbing media, and absorption rate relates to the solubility, absorption power, and three-dimensional structure. 23 refs., 7 figs., 4 tabs.

  15. FY1995 study of very flexible software structures based on soft-software components; 1995 nendo yawarankana software buhin ni motozuku software no choju kozo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose of this study is to develop the method and tools for changing the software structure flexibly along with the continuous continuous change of its environment and conditions of use. The goal is the software of very high adaptability by using soft-software components and flexible assembly. The CASE tool platform Sapid based on a fine-grained repository was developed and enforced for raising the abstraction level of program code and for mining potential flexible components. To reconstruct the software adaptable to a required environment, the SQM (Software Quark Model) was used in managing interconnectivity and other semantic relationships of among components. On these two basic systems, we developed various methods and tools such as those for static and dynamic analysis of very flexible software structures, program transformation description, program pattern extraction and composition component optimization by partial evaluation, component extraction by function slicing, code encapsulation, and component navigation and application. (NEDO)

  16. FY 1998 report on the results of the project on the next generation structure housing development; 1998 nendo jisedai kozo jutaku kaihatsu jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The purpose of this project is to develop/verify technology to design/construct a structural body of multiple dwelling house which is highly durable and usable at maximum of the limited space with no projections of poles/beams, and is also to develop/verify a composite system of a structure and each house in which residential space can freely be changed horizontally/vertically in response to the leveling-up of living and changes in life style. The following were conducted: construction of an experimental house group with next generation structure; development of technology of effective space utilization/high durability body construction; development of technology of structural analysis/design systematization of antiseismic/damping system; development of commercialization of technology to heighten frame durability, development of technology to heighten durability of finishing materials of a body; development of low cost construction technology; development of technology of interface between a body and each house; verification of housing performance using a next generation body system; generalization of next generation frame system/house system. To reflect the results of the research quickly, the details of the research are systematized, and a draft is worked out of a guide for constructing the next generation frame system/house system which were arranged between the current architecture related laws and business as a general multiple dwelling house. (NEDO)

  17. Mesoporous activated carbons with metal-oxide particles prepared from Morwell coal; Morwell tan wo genryo to shita kinzoku sankabutsu tanji kasseitan no saiko kozo

    Energy Technology Data Exchange (ETDEWEB)

    Yoshizawa, N.; Yamada, Y.; Shiraishi, M. [National Institute for Resources and Environment, Tsukuba (Japan); Kojima, S.; Tamai, H.; Yasuda, H. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1996-10-28

    The metal dependence of mesoporous activated carbons with various metal acetylacetonate (acac) particles prepared from Morwell coal was studied. In experiment, the mixture of Morwell coal and acac metal complexes were dissipated into tetrahydrofuran, and after agitation in Ar atmosphere, the solvent was removed by vacuum distillation. Coal specimens with Fe(acac)3, Ni(acac)2 and Co(acac)2 as acac complexes were activated by exchanging flow gas with water vapor after heat treatment in N2 gas flow at 900{degree}C. The pore sizes of the specimens were obtained from N2 adsorption isotherms by BET method and BJH method. Conditions of pores and metals in the specimens were examined by XRD measurement and TEM observation. The relation between the above conditions and pore characteristics obtained from adsorption experiment was also examined. As a result, the difference in mesopore ratio between the specimens and blank specimens was larger in the order of Fe, Co and Ni, and the effect of added metal complexes was also larger in this order. 3 refs., 3 figs., 3 tabs.

  18. Bond cleavage reactions of the bridge structure in coal in the presence of hydrogen donating compounds; Suiso kyoyosei kagobutsu sonzaika deno sekitanchu no kakyo kozo no kairetsu hanno

    Energy Technology Data Exchange (ETDEWEB)

    Bando, N.; Kidena, K.; Murata, S.; Nomura, M. [Osaka University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    In this paper, bond cleavage reactions are discussed in relation to the softening and solubilization of coal. Were used 9,10-dihydroanthracene (DHA) and 9,10-dihydrophenanthrene (DHP) as models of hydrogen donating compounds in coal, and bibenzyl, 1,2-diethane, benzylphenylether, and 1,5-dibenzylnaphthalene were used as models of bridge structure compounds. They were compared mutually, as to reactivity of coal against DHA and DHP. For the homolytic cleavage of bridges, DHA with excellent radical supplement performance provided excellent hydrogen donating performance. While, for the ipso-position cleavage of bridges, it was found that DHP can act as an effective hydrogen donor. For the reaction between coal and hydrogenated aromatic compounds, cleavage of relatively weak bonds, such as ether linkage and dimethylene linkage, occurred at about 380{degree}C, and hydrogen from DHA or DHP was consumed. On the other hand, the results suggested that the cleavage reaction at ipso-position affected by hydrogen donating solvent is also important at temperature range around 420{degree}C. 2 refs., 3 figs., 1 tab.

  19. Optimum stamping die structure based on analytical method of die deformation during draw process; Seikei katei no kanagata henkei kaiseki ni motozuku, press kanagata kozo no saitekika

    Energy Technology Data Exchange (ETDEWEB)

    Nakahara, T; Tamai, H [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    We measured an actual deformation and pressure distribution in draw process of bending cam, and analyzed deformation process of die structure, in order to eliminate adjusting work considering die deformation by stamping force. We studied die structure improvement with simulation based on analytical method. This report describes a sample of die structure improvement based on a simulation and actual measurement. 1 ref., 11 figs., 1 tab.

  20. Characteristic analysis of turbulent heat diffusion in a multi-compartment structure; Takukakuka kukan kozo ni okeru ranryunetsu kakusan gensho no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Hu, C; Fukuchi, N [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-10-01

    An analysis was made on turbulent heat diffusion in a multi-compartment structure necessary for designing calorific power and environment for functional systems used in marine vessels and off-shore structures. In a multi-compartment structure, the diffusion phenomenon is complex because of movement of air flow in turbulence and buoyancy resulted from non-isothermal condition. The phenomenon is largely affected by space shapes and walls, and the conditions in heat diffusion field is governed also by shapes of opening connecting the compartments. An analysis was made by using the SIMPLE method on turbulent heat diffusion in a multi-compartment space with high Raleigh number in which natural convection is dominant. If the opening is small, the Coanda effect appears, in which air flow passing through the opening rises along the wall, wherein a high-temperature layer is formed near the ceiling, making the heat diffusion inactive. If the opening is large, a jetting flow from the opening and a large circulating flow are created, which cause active advection mixture, making temperature gradient smaller in the upper layer. Heat transfer intensity in an opening on a partition wall decays in proportion with 1/4th power of the opening ratio. 7 refs., 11 figs.

  1. Fiscal 1994 survey report. Survey of energy supply/demand structure sophistication and global environmental impact; 1994 nendo energy jukyu kozo kodoka chikyu kankyo eikyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Outlines of various energy supply/demand analytical models are surveyed. With environmental problems gathering importance, a number of models are being introduced in which energy supply/demand structures, long-term climate changes, and impacts of policy options on social economy are linked to each other. Some socioeconomic impact models cover a single country and others the whole world. They are various in type, ranging from dynamic optimization models to static balance models. Twenty-four models are chosen, and grouped into two types respectively covering Japan and the whole world from a geographical viewpoint and into three groups in view of their structures. Under an optimization model, such optimization is accomplished as economic growth maximization and energy cost minimization and so forth under given energy supply restrictions. Under a general balance type econometric model, an adjustment process in which capital and labor and production are coordinated across multiple departments is expressly stated. Under a partial balance type econometric model, a demand function for goods is given and optimum behavior such as consumption maximization is indirectly described. (NEDO)

  2. Fabrication of low cost high performance large size composite structures by electron beam curing (EBC); Denshisen koka (EBC) ni yoru tei cost koseino ogata fukugozai kozo no seizo

    Energy Technology Data Exchange (ETDEWEB)

    Kamimura, K.; Parrot, P.

    1996-03-15

    This article introduces the electron beam curing (EBC), which is high speed non-heating cure technique for the high performance resin for structures, conducted by Aerospacial Co., Ltd. In this technique, very strong electron beam and X-ray are used in response to the thickness of curing region of members, and the muzzle has energy of 10 MeV as permeation control energy and power of 20 kW as cure time control power. Advantages of fabrication of composite products by EBC is derived from the elimination of exoergic and heating curing processes and the local cure molding. For the EBC, the residual stress is not generated, the size is stable, the insertion of different materials is easy without mismatch of thermal expansion between the composites and metals, the homogeneous bridge can be obtained to stabilize the material quality, the processing time can be shortened, it is suitable to mass production, and the cure of products can be controlled. About 30% to 40% of the cost of products can be reduced. 1 ref., 6 figs., 1 tab.

  3. Basic investigation on deflection wave propagation and strength of very large floating structures; Choogata futai kozo no tawami hado denpa kyodo to kyodo ni kansuru kisoteki kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsubogo, T.; Okada, H. [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering

    1997-08-01

    The response strength in which deflection waves propagating in the elastic body of a large floating structure with an order of km in length and width was investigated. Attention was paid to the waves propagating the place fully away from the boundary of a very large floating body so as to obtain the dispersion relation of waves and the relation between incident waves and deflection waves. Next, the frequency response was checked from the aspect of the displacement amplitude and strength for beams and plates. The dispersion relation of waves propagating the place fully away from the boundary of a very large floating body and the relation between the waves and infinite-point incident waves were represented by an expression. Similarly, the waves propagates more than the infinite-point incident waves in frequency, wavelength, and speed. A lower-limit value exists in the propagation speed. The displacement and stress amplitudes are represented by a relational expression. For plates, the displacement amplitude increases when the wave direction coincides with the small-rigidity direction. The stress amplitude is maximized when the waves corresponding to the ``wave below a floating body = size of a characteristic wave number`` reach the large-rigidity direction. 10 refs., 10 figs., 2 tabs.

  4. Extension of the Fukaya fault and deep structure of the Konan terrace; Fukaya danso no encho to Konan daichi no chika kozo

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, K; Kano, N; Yokokura, T; Kiguchi, T; Yokota, T; Tanaka, A [Geological Survey of Japan, Tsukuba (Japan); Sato, H [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1997-10-22

    With an objective to elucidate the relationship between the central tectonic line in the Kanto area and the active faults appearing in topography, seismic exploration using the reflection method has been carried out. The course of traverse was set in the south west to north east direction starting from the north east part of the Kanto mountainous area to the Menuma lowland passing through the Konan high plain. The line crosses nearly perpendicularly the direction in which the general beds in this area run. A 400-kg weight was used as a vibration source in the western half of the course of travel, and the MinivibT15000 (made by IVI Corporation) in the eastern half. Considerations given based on the preliminary CMP polymerization time cross section may be summarized as follows: the Fukaya fault cannot be tracked topographically further to the south east side than Mikejiri in Kumagaya City, but the reflection face from CMP 2050 to about 2100 shows an inclined bed on the south west side and a horizontal bed on the north east side; judging from change in the inclination in the beds, the Fukaya fault is thought to extend to the south east direction; the location of inclination change on the cross section turns to the south west side as the depth increases; and, if this is regarded as the fault face, the Fukaya fault could be said an inverse fault. 5 refs., 2 figs.

  5. Simulation of fault-bend fold by incompressible Newtonian fluid; Hiasshukusei Newton ryutai ni yoru danso oremagari shukyoku kozo no simulation

    Energy Technology Data Exchange (ETDEWEB)

    Tamagawa, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-10-22

    Incompressible Newtonian fluid simulation is experimentally applied to faults typical of the compression and extension fields. A fault-bend folding structure of the flat-ramp flat fault in the compression field and a folding structure of a normal fault in the extension field are studied, and the results are compared with those obtained by the balanced cross section method. The result of calculation indicates that the velocity gradient with the ramp angle set at 30deg is correspondent to stress and that stress concentration is taking place at the ramp section of the fault. This solution is an approximation and does not necessary support the conservation of area but, when the ramp angle is allowed to change from 10 through 40deg, it is found that the conservation of area holds though roughly. It is found that the configuration of the folding structure formed by a flat-ramp flat fault is positioned between the anomalous-mode layer parallel shear typical of a balanced cross section and the folding structure formed by a vertical shear. 7 refs., 7 figs.

  6. Estimation of underground structures in Kyoto city by seismic-array observations of microtremors; Bido no array kansoku ni yoru Kyoto shinai no chika kozo tansa

    Energy Technology Data Exchange (ETDEWEB)

    Miyakoshi, K; Kagawa, T; Akazawa, T [Osaka Soil Test, Osaka (Japan); Ogawa, Y; Shimizu, K [Osaka Gas Corp., Osaka (Japan); Ejiri, J [Obayashi Corp., Tokyo (Japan)

    1997-10-22

    Observations of microtremors were carried out to estimate the S-wave velocity structure by using arrays of seismographs around the Kyoto Research Park. The observation points were so arranged that equilateral triangle arrays may be formed with maximum radii at 0.2 km, 0.4 km and 0.8 km respectively with the premises of the Kyoto Research Park as the center. The seismographs have used seven vertical movement components (PELS), and were adjusted to a period of eight seconds. In addition, high-cut filters of 4 Hz were used because the observation areas are located in urban areas with heavy traffic. The analysis has used the spatial self-correlation method as a means to estimate phase velocity of surface waves contained in microtremors. As a result, phase velocity estimation has become possible for frequencies from about 0.4 Hz to 2 Hz, whereas the S-wave velocity structure was estimated to a depth of down to about 900 m by using as reference the result of the reflection method exploration having been carried out in the present areas. In addition, it was suggested that microtremors with frequencies higher than 1 Hz are in unsteady state in terms of time or space. 4 refs., 7 figs., 1 tab.

  7. Experimental analysis of the structure attenuation characteristics on engine noise by pseudo cylinder pressure excitation; Giji tonaiatsu kashin ni yoru engine kozo no soon tokusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ozawa, H; Nakada, T [Isuzu Advanced Engineering Center, Tokyo (Japan)

    1997-10-01

    The engine structure attenuation has been experimentally analyzed by the newly developed in-cylinder excitation system. It can reproduce the complete cylinder pressure in non-running engine conditions by adopting the hydraulic and the piezoelectric actuator. The structure attenuation measured in this system has a good coincidence with the ones measured in actually engine operating conditions, meanwhile the current method, which applied only high frequency components as the excitation pressure, was shown to have the unsatisfied agreement. As a result, the proposed system has been concluded to be very useful to estimate the engine noise characteristics in non-running conditions. 4 refs., 11 figs., 1 tab.

  8. Geoelectrical structure by electrical logs and Schlumberger sounding at the Akinomiya geothermal field, Akita Prefecture; Denki kenso oyobi Schlumberger ho ni yoru Akinomiya chinetsu chiiki no hiteiko kozo

    Energy Technology Data Exchange (ETDEWEB)

    Kajiwara, T; Takemoto, S

    1997-05-27

    Based on the electrical logging data of the existed well and Schlumberger sounding data obtained in 1974, a two-dimensional inversion analysis of the specific resistance profile was conducted at the Akinomiya geothermal field, Akita Prefecture. From the electrical logging data, relationships between the geology and the specific resistance were illustrated. The specific resistance values of basement rocks showed more than 100 ohm-m, which were higher than those of the other seams. Intrusive rocks and tuffs in the basement rocks showed locally low values less than 100 ohm-m. Younger volcanic rocks showed low values around 10 ohm-m. As a result of the two-dimensional inversion analysis, the basement rocks could be detected as high specific resistance layers. Accordingly, it was considered that the basement rocks in this field can be detected as high specific resistance layers by analyzing the results of field survey sufficiently. Low specific resistance zones were observed in the shallow depth, which corresponded to the fumarolic gases. There were some layers with remarkably varied specific resistance values, which were considered to be related with alteration. 6 refs., 3 figs.

  9. Efficient calculation of potential distribution in two-layer earth; Niso kozo daichikei ni okeru denki tansa no tame no koritsuteki den`i keisan shuho

    Energy Technology Data Exchange (ETDEWEB)

    Kataoka, M; Okamoto, Y [Chiba Institute of Technology, Chiba (Japan); Endo, M; Noguchi, K [Waseda University, Tokyo (Japan); Teramachi, Y; Akabane, H [University of Industrial Technology, Kanagawa (Japan); Agu, M [Ibaraki University, Ibaraki (Japan)

    1997-05-27

    An efficient calculation method of potential distribution in the presence of an embedded body in multi-layer earth has been proposed by expanding the method of image with a consideration of multiple reflection between the ground surface and each underground boundary. For this method, when solving boundary integral equation with the potential of embedded body surface as only one unknown, i.e., when obtaining discretization equation, ordinary boundary element program developed for analyzing the finite closed region can be used. As an example, numerical calculation was conducted for the two-layer earth. The analysis expression of potential distribution in the case of the certain embedded body in two-layer earth has never published. Accordingly, the calculated results were compared with those by the integral equation method. As a result, it was concluded that the primary potential obtained from the present method agreed well with that obtained from the integral equation method. However, there was a disregarded difference in the secondary potential. For confirming the effectiveness, it was necessary to compare with another numerical calculation method, such as finite element method. 5 refs., 5 figs.

  10. Subsurface interpretation based on geophysical data set using geothermal database system `GEOBASE`. 2; Chinetsu database system `GEOBASE` wo riyoshita Kakkonda chinetsu chiiki no chika kozo kaiseki. 2

    Energy Technology Data Exchange (ETDEWEB)

    Osato, K; Sato, T; Miura, Y; Yamane, K [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Doi, N [Japan Metals and Chemicals Co. Ltd., Tokyo (Japan); Uchida, T [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-05-27

    Five cross sections were applied as a result of MT method investigations in addition to the results of conventional analyses at the Kakkonda geothermal area; three-dimensional resistivity distribution was made into a database by using the Kriging method which makes a matching with anisotropy of seismic center distribution in micro-earthquakes; and the database was compared with the data derived from surveys on the pilot survey well WD-1a and the side-truck well WD-1b thereof. As a result, it was found that the well WD 1b which encountered a water loss zone had the water loss zone exist in a region with relatively lower resistivity than in the well WD-1a which did not encounter a water loss zone. The region in which the water loss zone was encountered existed in a very steep slope region going from the high resistivity region in the west side toward the low resistivity region in the east side. This fact suggests a possibility that fractures have developed in this region with sharp slope in the resistivity in this area. Adding three-dimensional complementary function to the GEOBASE database by using a simple Kriging allowed the direction of anisotropy in spatial data to be freely and quickly decided. It was learned that this capability exhibits strong power in a mapping work in structures where such anisotropy as a geothermal zone is highly dominant. 5 refs., 8 figs., 2 tabs.

  11. X-ray diffraction analysis and MO calculations of 1H-tetrazole; 1H-tetorazoru no Xsen kessho kozo kaiseki to bunshi kido keisan

    Energy Technology Data Exchange (ETDEWEB)

    Ono, Yoshio.; Akutsu, Yoshiaki.; Arai, Mitsuru.; Tamura, Masamitsu. [The University of Tokyo, Tokyo (Japan). School of Engineering; Matsunaga, Takehiro. [National Institute of Materials and Chemical Research, Tsukuba (Japan)

    1999-02-28

    The X-ray diffraction analysis and the MO calculations of 1H-tetrazole were carried out, in order to explain its high stability. From the X-ray diffraction analysis, five bonds in the ring have intermediate lengths between single and double bond lengths. Therefore, 1H-tetrazole is quite stable because of its aromaticity. The N1-C5 distance of 1.315A is significantly short. The molecular structure which was calculated by the ab initio MO calculation of one 1H-tetrazole molecule at MP2/6-31G* level, showed a good agreement with our experimental one, except for the abnormal short N1-C5 distance. From the calculations of dimers and trimers, 1H-tetrazole is shown to be stabilized by a strong intermolecular electrostatic interaction between the protons and the delocalized electrons over the ring. (author)

  12. Fiscal 2000 report on result of the full-length cDNA structure analysis; 2000 nendo kanzen cho cDNA kozo kaiseki seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper explains the results of research on full-length cDNA structure analysis for the period from April, 2000 to March, 2001. The outline of human genome sequence was published in June, 2000. In Japan, human gene analysis was such that, as the basic technology of the bio industry, a millennium project was decided in the budget of fiscal 2000. The full-length cDNA structure analysis is the core of the project. The libraries of cDNA were prepared using full-length and more than 4-5kbp-long cDNAs by oligo-capping method. It began from determining partial sequence data at end cDNA, and then, with new clones selected therefrom, full-length human cDNA sequence data were determined. The partial sequence data determined by fiscal 2000 were 1,035,000 clones while the full-length sequence data were 12,144 clones. The sequence data obtained were analyzed by homology search and translated into amino acid coding sequences, with predictions conducted on protein functions. A clustering method was examined that selects new clones from partial sequences. Database was constructed on gene expression profiles and disease-related gene sequence data. (NEDO)

  13. Buckling collapse analysis of framed structures by using adaptively shifted integration technique. Junnogata shifted intergration ho ni yoru honegumi kozo no zakutsu hokai kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Toi, Y.; Isobe, D. (The University of Tokyo, Tokyo (Japan). Institute of Industrial Science)

    1993-09-01

    This paper describes the following matters on application of an adaptively shifted integration technique to a buckling collapse analysis of framed structures: This method is a method in a finite element analysis using three-dimensional girder elements to arrange value integration points at optimal locations in a linear analysis if the elements are in an elastic transform condition on the whole. The method then moves the value integration points so that plastic hinge will occur in these locations immediately after part of the elements has yielded. The method was applied to analyzing an elastic buckling problem in several loading patterns for either a both-end supported or a one-end fixed beam member. A result was obtained that a number of elements required for one member is four at minimum. In a buckling analysis of framed structures, a satisfactory result was obtained by using an automatic element segmenting algorithm, which begins the analysis with one element one member, and immediately after a member is determined with a possibility of generation of buckling, splits that member only into four elements. 6 refs., 5 figs.

  14. Structural studies on reaction centers from thermophilic photosynthetic bacteria and its functional utilizations. Tainetsusei kogosei saikin ni yuraisuru kogosei hanno chushin no kozo kaimei to kino kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nozawa, T; Morishita, Y; Kobayashi, M; Kanno, S [Tohoku University, Sendai (Japan). Faculty of Engineering

    1992-10-31

    This paper describes the results of the experiment in which crystallization of protein of reactive center purified from the photosynthetic film of thermophilic purple sulfur photosynthetic bacterium Chromatium tepidum whose hyrogen donor in photosynthesis is H2S instead of H2O was attempted. Crystallization was carried out by the vapor diffusion method and particularly by using ethylene glycol as precipitator at 4[degree]C after various investigations on the conditions of crystallization. By X-ray diffraction, this crystal was found to belong to the rhombic system, and it was estimated that the lattice constants, a, b, c equal to 140[angstrom], 190[angstrom] and 80[angstrom] respectively. This bacterium is a thermophilic bacterium having the optimum growth temperature of 48-50 [degree]C and utilizes CO2 or H2CO3 as corbon source, ammonium, urea etc. as nitrogen source and thiosulfate as sulfur source. Moreover, another purpose of this investigation was to determine the thermophilic location by elucidating its configuration (although, as a result, the analysis of configuration had no sufficient resolution). It was confirmed that the enzyme system of photosynthetic film and its cytoplasm obtained by ultrasonic spallation of this cell have CO2 fixing activity utilizing light energy. 23 refs., 14 figs., 3 tabs.

  15. Life prolongation and cost reduction of steel ladles with improving refractories and their structure; Taikabutsu zaishitsu to kozo kaizen ni yoru shuka taikabutsu no chojumyoka to kosuto teigen

    Energy Technology Data Exchange (ETDEWEB)

    Nakai, Masato; Kasahara, Hajime; Fukutani, Fujio; Imai, Hiroyuki [Nippon Steel Corp., Tokyo (Japan)

    1999-06-01

    Steel Making Plant, Hirohata Iron Works, Nippon Steel Corp. succeeded to reduce the cost of furnace materials by measures described below down to 49% compared to that in 1992. (1) For tuyre bricks, cleanability against oxygen was improved by compacting by vacuum cast forming. (2) For SL bricks, the cost was reduced by applying imported bricks and optimization of the range of use. (3) For alumina-magnesia amorphous refractories for side walls, low expansion and breaking resistance were improved by optimization of magnesia quantity and silica ultra fine powder quantity. (4) For side wall structure, improvement of tie-in between the ground part and the side wall and lining with efficient thickness were carried out. (NEDO)

  16. Nonlinear effects and vortical structures in homogeneous rotating turbulence under stable density stratification; Antei seisoka ni aru kaiten ichiyo ranryu no hisenkei koka to uzu kozo

    Energy Technology Data Exchange (ETDEWEB)

    Tsujimura, S.; Iida, O.; Nagano, Y. [Nagoya Institute of Technology, Nagoya (Japan)

    2000-02-25

    The generation mechanism of the vertical vortices associated with the baroclinic instability and the effects of nonlinear term on the vortices are investigated by using both direct numerical simulation (DNS) and rapid distortion theory (RDT). Two kinds of the anisotropic flow fields are used as initial conditions. As a result, the initial anisotropy of Reynolds stresses is found to affect asymmetry of the vertical vortices. In the cases where the initial vertical velocity is set to be zero, the p. d. f. of the vertical vorticity tends to incline toward the anticyclonic side. When the vertical component of initial velocity is larger than the horizontal one, the cyclonic vortices are more enhanced. By comparing DNS and RDT, it is found that in both cases of the initial conditions the enhanced vortices of DNS are stretched in the vertical direction, which is not observed in the RDT results. This should be because the nonlinear vortex-stretching term intensifies and elongates vertical vortices in the vertical direction. The anticyclones are markedly augmented in low Prandtl number fluids, while the cyclones become dominant in the high Prandtl number case. In particular, the flow field becomes almost two-dimensionalized and Taylor columns are formed in the vertical direction in the low Prandtl number case. However, neither two-dimensionalization nor Taylor column is observed in the RDT analysis which neglects the nonlinear terms. (author)

  17. Coal structure construction system with construction knowledge and partial energy evaluation; Kochiku chishiki to bubunteki energy hyoka ni yoru sekitan bunshi kozo kochiku system

    Energy Technology Data Exchange (ETDEWEB)

    Okawa, T.; Sasai, T.; Komoda, N. [Osaka University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    The computer aided coal structure construction system is proposed, and a computational construction example is presented. The coal structure construction engine of this system fabricates molecular structure by connecting fragments sequentially inputted through a user interface. The best structure candidate is determined using construction knowledge and partial energy evaluation every addition of one fragment, and this process is subsequently repeated. The structure evaluation engine analyzes the 3-D conformation candidate by molecular dynamics, and evaluates the conformation by determining the energy value of an optimum structure. As an example, this system was applied to construction of coal molecular structure based on the actual data of partial structure composed of 26 structures from 2l kinds of aromatic cluster structures, 27 bonds from 2 kinds of bridged bonds, and 16 groups from 2 kinds of terminal substitutional groups. As a result, this system could construct a superior structure according to expert knowledge from the viewpoint of energy. 6 refs., 5 figs., 2 tabs.

  18. Correlation between the structural relaxation and the functionality of optically functional glasses; Kokinosei glass ni okeru kozo kanwa to kinosei no sokan

    Energy Technology Data Exchange (ETDEWEB)

    Nishida, T [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1994-12-15

    A discussion was given to elucidate the correlation between the crystallization of infrared ray permeating glass and the infrared ray permeability. The elucidation used infrared ray permeation spectrum, infrared ray absorption spectrum, and the Mosbauer effect. Reduction in permeability due to heat treatment of aluminate glass was discussed from the crystallization mechanism. Ultrafine crystals of mayenite phase having a composition ratio of CaO/Al2O3 = 1.7 diffuse and grow from the glass surface into interior as a result of heat treatment. The crystal growth is triggered by severance of Al-O tetrahedron. Gallate glass has CaGa2O4 and small amount of CaFe2O4 phase deposited when it is heat-treated in the vicinity of Tg. Although the infrared ray permeability decreases in association with the crystallization, the decrease is limited to crystallization on the glass surface, hence the permeability will not fall to zero. Laser irradiation on the gallate glass causes crystallization, resulting in reduced infrared ray permeability. Semi-stable Ca3Ga4O7 phase remains, however, because the heat energy amount is not large. Tellurite glass has {alpha}-TeO2 and a small amount of telluric acid iron deposit when heat-treated. 29 refs., 10 figs.

  19. Integration of the market of the European Community and the change of the industrial structure; EC shijo togo to sangyo kozo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, T; Uno, K; Tanimoto, T; Yamashita, T [Osaka Sangyo University, Osaka (Japan). Institute for Industrial Research

    1994-11-22

    This paper describes progress of the cooperation as to the integration of EC market and the change of industrial structure. For the structural change in the industry and economy accompanied by the integration of EC, effects of the Maastricht Treaty on the economic structure of EC are described. It is considered that the EC countries are affected by the political and economical restrictions due to the agreement of this treaty. For the change in the distribution structure accompanied by the integration of EC, obstruction factors of the deregulation of EC transportation market are especially investigated. Differences in the distribution capacity, various regulations and standards, and labor condition among individual countries are pointed out as the obstruction factors. For the unity of Germany and its economical and administrative influence, various problems are pointed out as to the economical confusion, progress in the de-nationalization of enterprises, management of real estate and land, etc. For the structural change in the road freight market in the member nations of EC, the structure of road freight market is made clear for the previous West Germany before the integration of European market. It is confirmed that the internationalization of the German domestic market is being promoted.

  20. Integration of the market of the European community and the change of the industrial structure. EC shijo togo to sangyo kozo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Tanimoto, T; Uno, K; Nakamura, T; Yamashita, S [Osaka Sangyo University, Osaka (Japan). Institute for Industrial Research

    1992-11-20

    This paper considers problems in the change of the industrial structure as a result of the EC market integration, and the change of the physical distribution structure, mainly in cargo transportation. The market integration is being moved forward mainly on liberalization of flows in people, materials, and currencies, but the material flow liberalization has not progressed noticeably because of difficulty in deregulations. Changes in the transportation structure on the whole in the EC countries would not see a complete removal of barriers supported by the transportation licensing system because of issues in protecting domestic transportation markets and sharing the road expenses, even if the tariff barrier has been removed as a result of the market integration. Amid the predictions on deregulated legislations and intensified competition associated with the integration, the French trucking industry is indicated of its direction toward a two-layer structure comprising large-scale enterprises and medium-to-small companies. The German unification created problems in transferring from the socialistic command economy to the capitalistic market economy. The paper gives considerations on the real state of affairs in the privatization policy of the people-owned enterprises in the former East Germany, and its economic and managerial problems that should be solved amid the large-area EC market integration based on the mutualism over and above the economic system transition.

  1. Crustal temperature structure derived from a ground temperature gradient chart of Hokkaido; Hokkaido no chion kobaizu kara motometa chikakunai ondo kozo

    Energy Technology Data Exchange (ETDEWEB)

    Okubo, Y. [Geological Survey of Japan, Tsukuba (Japan); Akita, F. [Hokkaido Geological Survey, Sapporo (Japan); Nagumo, S. [Oyo Corp., Tokyo (Japan)

    1997-05-27

    The Hokkaido Underground Resources Investigation Institute has prepared in 1995 a detailed temperature gradient chart that shows local anomalies around volcanoes. This paper describes an attempt to derive crustal temperature structure of Hokkaido from the above data. The model was hypothesized as a primary model in which no thermal convection exists. In volcanic and geothermal areas which show a temperature gradient of more than 100 {degree}C km {sup -1}, a solidus temperature is reached at a depth shallower than 10 km. Below the volcanic chain forming the Chishima arc, a partially melted region exists in a width of about 100 km. Most of the areas in the southern Hokkaido have the temperature reached the solidus temperature in the crust. On the other hand, in most of the areas of the forefront side, no solidus temperature is reached in the crust. In the temperature structure of a cross section crossing almost orthogonally with the volcanic front passing through Mt. Daisetsu, a high temperature area reaches to a shallow portion beneath Mt. Daisetsu, where the depth at which the solidus temperature is reached is 10 km or shallower. The range of area where the solidus depth is shallower than 10 km has a south-west width of about 40 km. This means that a partially melted area with a size of 40 km in the horizontal direction exists at a depth of several kilometers. 20 refs., 3 figs.

  2. Bayesian reliability analysis for non-periodic inspection with estimation of uncertain parameters; Bayesian shinraisei kaiseki wo tekiyoshita hiteiki kozo kensa ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Itagaki, H. [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Asada, H.; Ito, S. [National Aerospace Laboratory, Tokyo (Japan); Shinozuka, M.

    1996-12-31

    Risk assessed structural positions in a pressurized fuselage of a transport-type aircraft applied with damage tolerance design are taken up as the subject of discussion. A small number of data obtained from inspections on the positions was used to discuss the Bayesian reliability analysis that can estimate also a proper non-periodic inspection schedule, while estimating proper values for uncertain factors. As a result, time period of generating fatigue cracks was determined according to procedure of detailed visual inspections. The analysis method was found capable of estimating values that are thought reasonable and the proper inspection schedule using these values, in spite of placing the fatigue crack progress expression in a very simple form and estimating both factors as the uncertain factors. Thus, the present analysis method was verified of its effectiveness. This study has discussed at the same time the structural positions, modeling of fatigue cracks generated and develop in the positions, conditions for destruction, damage factors, and capability of the inspection from different viewpoints. This reliability analysis method is thought effective also on such other structures as offshore structures. 18 refs., 8 figs., 1 tab.

  3. Global environment assessment survey by advancing the energy demand and supply structure. 4; Energy jukyu kozo kodoka chikyu kankyo eikyo chosa. 4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To investigate the energy demand and supply structure in Japan, the international trend of approaches to global warming problems and the mitigation options to global warming in the energy related sectors have been surveyed. For the United Nations Framework Convention on Climate Change, an Ad-hoc Group has discussed relevant topics after the 1st conference of the Parties. Meetings of the Group primarily focused on what objectives to set for the reduction of greenhouse gas (GHG) emissions in and in and after 2000. IPCC completed their Technical Paper in November 1996 in which technologies and measures to reduce GHG emissions and to enhance GHG sinks were analyzed and evaluated in various aspects. This Paper discusses about each sector of institutional buildings sector, transport sector, industrial sector, and energy supply sector. Especially, in the energy supply sector, promising approaches to reduce future emission include more efficient conversion of fossil fuels, switching to low-carbon fossil fuels, decarbonization of flue gas and fuels, CO2 storage, switching to nuclear energy, and switching to renewable sources of energy. 5 refs., 2 figs., 14 tabs.

  4. Studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; Handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, H; Sona, S; Koike, H; Hori, H; Negishi, N; Kohara, H; Ibusuki, A [National Institute for Resources and Environment, Tsukuba (Japan); Vakhtin, A; Borovkov, V [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    Studies are made to define the working mechanism of semiconductor photocatalysts such as TiO2 and to establish designing guidelines for improving on their activity and functions. TiO2 in the air actively produces oxygen seeds for the oxidation and removal of NOx, etc. It is desired that a catalyst have a specific surface area large enough to retain the product of its action. To meet the need, a thin-film photocatalyst which is an aggregate of TiO2 crystals is produced by burning a film of a sol/gel system of reaction doped with macromolecules. This product has a larger specific surface area and is higher in pollutant-removing performance, and may be put into practical use. In another experiment, metal-carrying particles TiO2 suspended in water are employed for the reduction of CO2. Though the main product of catalysts carrying Pt or Pd is methane, a photocatalyst carrying RuO2 produces acetic acid mainly and loses less activity with the passage of time. A hybrid photocatalyst is composed of an organic pigment and inorganic semiconductor, synthesized through a covalent bond between a sililated-surface thin TiO2 film and porphyrin. It is confirmed that the newly developed process brings about an increase in electron migration efficiency. 3 figs.

  5. Survey of effects of enhancement of the energy supply/demand structure on the global environment. 3; Energy jukyu kozo kodoka chikyu kankyo eikyo chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of studying how the energy supply/demand structure in Japan should be, a report on the secondary IPCC (Intergovernmental Panel on Climate Change) evaluation was analyzed. Possibilities of reducing the world CO2 emissions in association with the energy consumption were studied in the five assumed cases. Every case says that CO2 can be reduced to 1/3 of the 1990 level by 2100. In a case of the use of biomass as main fuel (1), the use of primary energy is suppressed to two times the 1990 level, and photovoltaic/wind/biomass power generation is introduced in a large quantity. Synthetic methanol and hydrogen are used for transportation and commercial/residential use fuels. There are four more assumed cases: the use of nuclear power as a substitute for renewable energy in the power generation in (1), the use of natural gas of 1.5 times that used in (1), the substitution of coal for biomass used in (1), and the assumption that the demand for primary energy in 2100 will be twice that used in (1). In Japan it is assumed that basically the nuclear power generation will be expanded, that the photovoltaic and waste power generation will be introduced in a large quantity, and that synthetic methanol and hydrogen are mainly used as transportation and commercial/residential use fuels. It is necessary, therefore, to analyze conditions under which the quantity introduction of such non-fossil energy is made possible. 11 figs., 31 tabs.

  6. NEDO coal mining structure adjustment subcommittee. 18th project report meeting; NEDO sekitan kogyo kozo chosei bunkakai. Dai 18 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    Concerning the subject matter, a NEDO (New Energy and Industrial Technology Development Organization) director Keishiro Kawamo reports on NEDO's projects designed to smoothly implement the 'new coal policy'. Nobuaki Terasaka, chief of the planning division, coal and new energy department, Agency of Natural Resources and Energy, takes up the current status of the coal policy and the tasks it faces, and discusses, predicting the development of the coal policy, the assurance of stable supply of coal from abroad, development of clean coal technologies that will rightly deal with the world-wide environmental problems, and the international diffusion of the clean coal technologies and the completion of the basement therefor. Concerning the 'development of zeolite-related commodities,' a report is delivered on the manufacture of a soil improving material and a deodorant for fish grill from zeolite found rich in coal layers of Pacific Coal Mine Co., Ltd. Concerning the 'polycrystalline diamond manufacturing project,' a polycrystalline diamond synthesizing method making use of the blasting technique employed at coal mines is reported. (NEDO)

  7. Report on fiscal 1998 investigation of Jozankei hot spring conservation and hot spring structure; 1998 nendo Jozankei onsen hozen chosa. Onsen kozo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-10-01

    With the purpose of evaluating recoverable hot water quantity and elucidating the change over a long term, investigations were carried out, with the results summarized, on the geology, alteration zone, gravitational analysis, fluid geochemistry and hydraulics in the area. The investigations covered the area of 7 km x 6 km in about 30 km southwest of Sapporo City and were performed for the period from September 10, 1998 to October 31, 1999. The results were as follows. In the Jozankei area, with the Usubetu layer in the Old Tertiary system as the basement, layers are superposed from the Palaeogene Oligocene to the Quaternary Pleistocene. Distributing in various places between Yunosawa vicinity and Jozankei Hot Spring area are acid to neutral geothermal alteration zones. The hot spring gushing-out zone in the Jozankei hot spring area is supposed to be regulated by side-by-side cracks in the NE-SW direction. It was inferred from tritium concentration and a minor component ratio that, as the mechanism of forming a hot spring, water of precipitation origin circulating and residing for a long time on the Usubetsu layer which is marine sediment is heated by a volcanic heat source latent in the depth. (NEDO)

  8. Learning model of eye movement system based on anatomical structure; Kaibogakuteki kozo ni motozuita gakushu kino wo motsu gankyu undo system to sono tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, X.; Wakamatsu, H. [Tokyo Medical and Dental University, Tokyo (Japan)

    1998-07-01

    A learning system is proposed to explain the adaptive function of an eye movement consisting of compensatory and optokinetic reflex, and pursuit movements based on the brain anatomy and physiology. Thereby, the learning system is synthesized as an artificial neural network based on the structure and function of the biological neural network of flocculus. The role of neural paths into flocculus from stretch receptors of ocular muscles are discussed in detail from the viewpoint of system control engineering. The mathematical learning process is also shown taking into account the adaptive mechanism and the anatomical structure of vestibular nuclei. The experimental results through simulation confirm the validity of the hypothesis and the appropriateness of the inference process in connection with the proposed mathematical model. 18 refs., 11 figs.

  9. Hybrid structure in civil engineering construction. Composite types of steel and concrete; Doboku bun`ya ni okeru fukugo kozo. Kozai to concrete no ittai keishiki

    Energy Technology Data Exchange (ETDEWEB)

    Sato, T. [JR Railway Technical Research Inst. Tokyo (Japan)

    1995-03-30

    In connection with hybrid structures in civil engineering construction, classification and application of composite types of steel and concrete are discussed. H steel embedded beam is a composite beam in which the H shape steel of the main beam is connected to rolled or welded H shape steel using cross beams. Composite structure columns are grouped into the composite column and the steel pipe concrete column. SRC piers are often adopted from the viewpoints of constraints for execution of works and vibration proof. Steel and concrete hybrid structure is a kind of structural system in which various kinds of materials such as steel, RC, or PC members are connected. The cable stayed bridge utilizes characteristics of steel and concrete effectively. For the piers of municipal expressway viaducts, there are executed cases of mixed structures which have RC, SRC columns for T shape piers and S structure for the bridges. SRC structure and composite columns are adopted often for structures of subway stations. 7 refs., 7 figs.

  10. Some studies on structural planning of long-span cable stayed bridge; Choshikan shachokyo no kozo keikaku ni kansuru 2,3 no kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Endo, T. [NKK Corp., Tokyo (Japan)

    1997-06-20

    Feasibility of cabled-stayed bridges with 1000m-grade spans is discussed while re-examining the plan for constructing a Great Tatara Bridge to connect Honshu and Shikoku, Japan, and in this process various tasks and questions are isolated. Some which will be problems in designing the new bridge structure are taken up, including the load-bearing capability of the bridge as a whole, vibration of long cables, resistance to long-period earthquakes, and accuracy management during the construction work. Findings are stated below. A cable-stayed bridge is not significantly different from a suspension bridge and is sufficiently feasible until the span exceeds 1500m. When the span is longer, however, the bridge beam cross section needs be designed very prudently in view of the great axial force and wind load to be imposed on it. Effective for the assurance of load-bearing capability for a long-span cabled-stayed bridge is a structure in which load is elastically confined in the direction of the bridge axis. In connection with vibration damping for very long cables, it is verified that a new dimpled cable suits the purpose of suppressing wind load from increasing without reduction in damping effect. 28 refs., 23 figs., 7 tabs.

  11. Creep analysis and torsional vibration analysis of cable-stayed bridges with two edge composite girders; Nishuketa gosei kozo shachokyo no creep kaiseki to nejiri shindo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Hoshino, M. [Nihon University, Tokyo (Japan). College of Science and Technology

    1996-07-21

    This paper describes the creep analysis and torsional vibration analysis of cable-stayed bridges with two edge composite girders. The girder is composed of the concrete slab and the steel girder. I-girders are placed at both edges of the profile. Such a type of bridge was investigated. As the stress migrates by the creep of concrete slab, it is necessary to evaluate the influence of this creep precisely in designing. In the analysis, the composite girder was expressed not by the single member, but by the binary member consisting of concrete member and steel member. Two methods were employed, i.e., method A in which both members are connected by the rigid body beam and method B in which the profile of concrete is converted into the profile of steel. The method A provided better accuracy, but the method B was often sufficient. Torsional rigidity of the open profile structure was much smaller than that of the box profile. As the torsional natural frequency was low, proper torsional vibration analysis was indispensable especially from the viewpoint of wind resistance. Two methods were employed, which utilize the vibration analysis method for general space frame structures. Results of both methods were agreed mutually, but the second method provided better calculation efficiency. 10 refs., 9 figs., 6 tabs.

  12. Studies on connecting structure between steel shell and steel reinforced concrete; Kokaku to tekkotsu tekkin concrete tono ketsugo kozo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Morimoto, A. [Kinki University, Osaka (Japan). Faculty of Science and Engineering; Morikawa, H.; Ito, N. [Metropolitan Expressway Public Corp., Tokyo (Japan)

    1996-02-15

    On the insert reinforcing bar structure for the connecting part of the main tower of cable stayed bridges, this paper reports verification results on a load resistant safety with a full-scale model, structure analysis and construction work. The basic structure was composed of a drilled steel shell, inserted reinforcing bars, fixing structure of bars in lining concrete of the shell and a pressure bearing plate. As an experimental result, the connecting part had a sufficient load carrying capacity against both tensile and compressive loads. The shear stress of the insert reinforcing bar structure was estimated successfully under von Mises`s condition. The shear spring constant in deformation characteristics was linearly proportional to an inserted reinforcing bar ratio. In earthquake, nearly 60% of an allowable compressive load was transferred to concrete through the pressure bearing plate. The analytical results of load resistant deformation characteristics of the connecting part well agreed with experimental ones, and the proposed analytical model was applicable to estimation of a dynamic behavior. 5 refs., 22 figs., 4 tabs.

  13. Proposal and study of a long-span composite cable-stayed bridge with new hybrid girder; Atarashii gosei kozo shuketa wo mochiita chodai fukugo shachokyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, K.; Hishiki, Y.; Furuichi, K. [Kajima Corp., Tokyo (Japan)

    1999-09-30

    A hybrid or mixed structure (composite structures) are a matter of increasing concern which takes in each advantage of steel and concrete. A field of bridges is no exception, with the plan and construction carried out for the new type of composite bridge, such as a composite cable-stayed bridge and a composite extra dose bridge as a long span bridge, and a composite truss bridge and a corrugated steel plate web bridge as a medium-span bridge, with technological development becoming active in this field. In such a technological trend, a hybrid two-girder structure was devised, a structure consisting of a concrete filled steel pipe for a girder and a precast (PC) floor plate for a floor board, as the girder structure of a long-span cable-stayed bridge in the subject research; also, applicability was examined using, as an example, the composite cable-stayed bridge with hybrid girders employed for the span. This paper reports the result of the analysis of the entire system, the analysis made for the purpose of examining the characteristic and the feasibility of this hybrid girder. The analysis revealed the structural feasibility of the long-span composite cable-stayed bridge using two hybrid girders of concrete-filled steel pipes thus devised. (NEDO)

  14. Bayesian reliability analysis for non-periodic inspection with estimation of uncertain parameters; Bayesian shinraisei kaiseki wo tekiyoshita hiteiki kozo kensa ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Itagaki, H [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Asada, H; Ito, S [National Aerospace Laboratory, Tokyo (Japan); Shinozuka, M

    1997-12-31

    Risk assessed structural positions in a pressurized fuselage of a transport-type aircraft applied with damage tolerance design are taken up as the subject of discussion. A small number of data obtained from inspections on the positions was used to discuss the Bayesian reliability analysis that can estimate also a proper non-periodic inspection schedule, while estimating proper values for uncertain factors. As a result, time period of generating fatigue cracks was determined according to procedure of detailed visual inspections. The analysis method was found capable of estimating values that are thought reasonable and the proper inspection schedule using these values, in spite of placing the fatigue crack progress expression in a very simple form and estimating both factors as the uncertain factors. Thus, the present analysis method was verified of its effectiveness. This study has discussed at the same time the structural positions, modeling of fatigue cracks generated and develop in the positions, conditions for destruction, damage factors, and capability of the inspection from different viewpoints. This reliability analysis method is thought effective also on such other structures as offshore structures. 18 refs., 8 figs., 1 tab.

  15. Achievement report for fiscal 1998 on research and development of multifunction members structure control technologies. Development of advanced surface treatment technologies for methane-fueled aero engines (1. Microstructure control technologies for ultrahigh temperature members); 1998 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu. Methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu (chokoon buzai mikuro kozo seigyo gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The carbon fiber reinforced carbon composite materials (C/C composites) strong at ultrahigh temperatures are taken up. So as to improve on its resistance to oxidation, corrosion, and abrasion as well as on its strength at ultrahigh temperatures, an ion engineering-assisted technique is used to reform the C/C composite surface layer and a technology is developed for thin coating formation on the C/C composite surface. Next, technologies are developed for multifunction coating formation on top of the surface, for defect prevention or removal from the C/C composite, and for adhesion enhancement between the C/C composite fibers and the matrix. Technologies are further developed for evaluating hostile environment withstanding capabilities at ultrahigh temperatures. In this fiscal year, in the study of microstructure controlling multilayer coating technologies, development is conducted of technologies of ion engineering-assisted surface control and reform and of technologies of forming multifunctional coatings high in reliability and resistance to corrosion. In the field of microstructure control composition, 3-dimensional carbon fiber reinforced carbon composite materials are manufactured by way of trial and evaluated, and their behavior under rigorous conditions is evaluated. (NEDO)

  16. FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (R and D of the intellectual material and structural systems); 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki kozo system no kenkyu kaihatsu (chiteki kozo system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the R and D project for development of intellectual materials and structural systems, where the fibrous or leafy sensor material or element (muscle) is integrated with a structure of an advanced material (skeleton) to process and control information (brain). The program for development of the health monitoring technologies successfully improves the fine FRG (Fiber Bragg Grating) as the high-performance sensor, equipped with a connector which allows the sensor to be easily connected to the normal diameter one, and develops various prototype sensors. The program for self-diagnosis of structural soundness and controlling damages verifies detection effectiveness of the embedded fine FRG sensor. The impact-related characteristics and damages of the reinforced flat plate are detected by embedding the optical fiber sensor. The program for developing the actuator materials and elements prepares the 20{mu}m thick piezoelectric sheet of adequate strength and toughness by dispersing the PNN-PZT system with partially stabilized zirconia (PSZ). The program for the function-gradient systems prepares the FGM driven at normal temperature, characterized by its structure of more evenly distributed stress, to evaluate its characteristics. It is proved to have high durability. The results of the comprehensive survey are also described. (NEDO)

  17. Study on fabrication methods of composite structures (1st. report); Joule effect curing of CFRP composite structures and its application to bonding and repair. Fukugo zai kozo no seikei kako ho ni kansuru kenkyu (Dai 1po); CFRP kozo no Joule koka wo riyo shita cure ho to setsugoter dot hoshu e no oyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Moriya, K. (The National Defense Academy, Kanagawa (Japan))

    1990-07-05

    A method for curing CFRP composite structures by using Joule effect is presented. Due to the presence of fiber to fiber contact, CFRP composites and their prepregs exhibit electrical conductivity in the direction transverse to fibers as well as in the fiber direction, and they can be considered as electrically homogeneous on a gross scale. Therefore, passing an electric current through a CFRP prepreg, it is self-heated due to the Joule effect. Feedback current control maintains the prepreg temperature at a desired level and makes the prepreg be cured by a specified cure cycle. Experimental verifiactions have been carried out to demonstrate the feasibility of the present technique. The applications to the bonding of CFRP components and to the patch repairs of effective CFRP structure are also described. 12 refs., 12 figs.

  18. Exploration of underground basement structures in Kanto plain using the spatial autocorrelation method. 1. S-wave velocity structure along the line from Hatoyama, Saitama to Noda, Chiba; Kukan jiko sokanho ni yoru Kanto heiya no kiban kozo tansa. 1. Saitamaken Hatoyama machi - Chibaken Nodashi kan no S ha sokudo kozo

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Umezawa, N; Shiraishi, H [Saitama Institute of Environmental Pollution, Saitama (Japan)

    1997-05-27

    The Saitama prefectural government has been conducting basement structure exploration using the spatial autocorrelation method by dividing the entire plain area into meshes, for the purpose of improving the accuracy of estimating large-scale seismic damages. This paper reports the result of explorations on meshes in the east-west direction in the central part of Saitama Prefecture. The present exploration was intended on ten meshes in the east-west direction along the north latitude 36-degree line. The number of exploration points is 13 comprising three points on the hilly area bordering on the eastern edge of the Kanto mountainous area and ten points on the plain area. The arrangement constitutes a traverse line with a total distance of about 33 km from the west edge (Hatoyama-machi in Saitama Prefecture) to the east edge (Noda City in Chiba Prefecture). The phase velocities were estimated from the result of the array microtremor observations using the spatial autocorrelation method applied with the FET. The phase velocities were used to estimate underground structures by using an inverse analysis. As a result, detailed two-dimensional S-wave velocity structures were revealed on the traverse line. The velocity cross section expresses change in the basement structures with sufficient resolution, and at the same time the information is judged highly harmonious with existing deep boring data and the result of artificial earthquake exploration. 15 refs., 6 figs.

  19. Analysis and evaluation of data to accompany the development of geothermal water use power plant, etc. Analysis and evaluation of polymeric materials exposed to geothermal heat at depths; Nessui riyo hatsuden plant nado kaiahtsu ni tomonau data no kaiseki hyoka. Shinbu chinetsuyo kobunshi zairyo no kaiseki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kenmochi, K.; Takahashi, J.; Takayanagi, H.; Tsuda, H.; Nagai, H.; Takeuchi, K. [Agency of Industrial Science and Technology, Tokyo (Japan); Nagasawa, C. [Kumamoto Prefectural Industrial Technology Center, Kumamoto (Japan); Hamada, T. [Science University of Tokyo, Tokyo (Japan). Faculty of Industrial Science and Technology

    1998-11-20

    Remaining life assessment technologies for polymeric materials for geothermal power generation and methods for improving their heat resistance are reviewed, and concepts of scale-free technologies for FRP (fiber-reinforced plastic)-sandwiched pipelines for hot water transportation are described. Materials based on PTFE (polytetrafluoroethylene) and NBR (acrylonitrile-butadiene rubber) are chosen for use as DHM (down-hole motor) sealing material and for application to the stator. With PTFE as the matrix, four candidates are prepared, which are additive-free PTFE, and GF/PTFE, GF/CF/PTFE, CF/PTFE, each containing 20w% GF (glass fiber) and/or 20w% CF (carbon fiber). With NBR serving as the matrix, two candidates are prepared, which are NBR-A containing 20w% aramid fiber and NBR-W which is a vulcanized NBR-A. External force, heat, light, and mud are named as the degradation factors, and each factor and some combinations of external force, heat, and light are repeatedly imposed on the materials. During the effort to develop an apparatus for simulating geothermal circumstances in which the factors will affect the materials in complicated ways, a life assessment technique is developed for such polymeric materials. A technology is developed for providing polymeric rubber elastomer with a heat resistant feature. A study is made to replace transportation pipelines for injection wells with FRP sandwiched pipelines. (NEDO)

  20. ONRASIA Scientific Information Bulletin. Volume 17, Number 4, October-December 1992

    Science.gov (United States)

    1992-12-01

    Singapore will soon etc.) but enabling technologies. We join Japan as the only Asian have to bear in mind that new Dr. Scow Boon Quek countries with...Thomas F. 3-237 Donoghue, Michael 1-137 Lu, Stephen 4-063 Flynn, Anita 2-099 Meyer, Robert A. 3-173 Fujii, Kozo 4-099 Moffett, Jonathan D. 1-061 Gibor

  1. FY 1999 report on the survey of the overseas geological structure, etc. Japan-Indonesia joint Tanjung Enim coal exploration project; 1999 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Indonesia sekitan kyodo tansa Tanjung Enim project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper summed up the FY 1999 results of the survey conducted based on the agreement on the Tanjung Enim IV coal exploration project which was concluded between NEDO and Indonesia's Ministry of Mining Energy. The survey was made for an area of approximately 40km{sup 2} which is a north block of the south Arahan region, Tanjung Enim, South Sumatra, Indonesia. To grasp the succession of strata/rock facies/geological structure and the state of existence of the coal seams to be drilled, surveys were conducted on ground surface and boreholes. A total of 10 holes was test-drilled, and all the boreholes were physically logged. As a result of the survey, each of A1, A2, B, C and E coal seams was confirmed as main seams. A1, A2 and B seams are low in ash and sulfur contents with heating values of approximately 4,800 kcal/kg, C seam is high in sulfur content, and E seam is high in heating value, 6,000 kcal/kg. As coal seams for open pit mining, existence of A, B and C seams is expected which lay in the shallow part from ground surface to sea level of 0m and in the range of depth of approximately 100m. The proved coal reserves of these coals were estimated at 189 million tons. (NEDO)

  2. Fiscal 2000 report on financially supported geological structure survey overseas. Basic survey for coal resource exploitation (Research on underground probing technology); 2000 nendo kaigai chishitsu kozo chosahi nado hojokin (sekitan shigen kaihatsu kiso chosa) konai tansa gijutsu chosa hokokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the work of searching for coal beds, comparison is made between the geological structure of the object area, which is predicted, before actual investigation, by a close scrutiny of the result of oceanic pilot boring conducted in the past, result of geophysical exploration, and the geological features of galleries already in presence in the vicinity, and the result obtained from galleries drilled actually for the investigation. The investigation was conducted at the Ikeshima coal mine, Nagasaki Prefecture. In this fiscal year, 5 investigation galleries were drilled, totalling 1640m in length, and, in the mine, geological surveys, survey and measurement, coal quality evaluation, water emergence investigation, boring for coal, etc., were carried out. Comparison was made, and, though in the 2nd Minami No. 06 air duct there was no important difference detected between the prediction and the actual result, some faults were found to exist which had not been predicted by seismic exploration on the ocean. In the 2nd Minami No. 5 air duct, the actual geology was not different from the predicted geology, this endorsing the usefulness of boring for coal. In the 2nd Minami No. 01 gallery, direction and inclination were not greatly different from what had been predicted, but some faults which had not been predicted were discovered. These faults had escaped the scrutiny of neighboring coal beds and pilot boring. (NEDO)

  3. FY1995 studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; 1995 nendo handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Development of the semiconductor photocatalyst such as titanium dioxide is important for photo-energy conversion and purification of the environment. We make clear that the mechanism of the photocatalysis using a spectroscopic or physico-chemical methods, and we developed the new photocatalyst with the control of the surface area, porosity, infinitesimal content, and surface modification of the catalyst surface. Titanium dioxide thin film photocatalysts were prepared by the dip coating method. Surface structure of the thin film was formed by the aggregated TiO{sub 2} anatase particle, its size was around 5 nm. This thin films effectively oxidazed NO, its photocatalytic activity is higher than that of commercial photocatalyst. Metal oxide anchored TiO{sub 2} photocatalysts (RuO{sub 2}/TiO{sub 2}) were prepared by the co-precipitation method. Effective charge separation of the RuO{sub 2}/TiO{sub 2} were confirmed by the measurement of ESR. The RuO{sub 2}/TiO{sub 2} photocatalyst successfully reduced CO{sub 2} and preserved its activity for much longer period than metal loaded catalyst. Hybrid photofunctionalized material was prepared by anchoring porphyrin moieties on the titanium dioxide surface. The relative quantum yield of electron transfer from porphyrin to the titanium dioxide conduction band has been markedly increased by water treatment of quanternized porphyrin-titanium dioxide covalently linked systems owing to removal of adsorbed porphyrin domains. (NEDO)

  4. FY 2000 survey of the geological structure overseas, etc. Japan-China joint coal exploration - Yu Xian project; 2000 nendo kaigai chishitsu kozo nado chosa - futai shiryoshu. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This data book summarized the proceedings and the technical report of the management committee on the Japan-China geological structure survey based on the consultation concluded between NEDO and China's bureau of coal field geology and a report meeting on the Yu Xian project. In the exploration, conducted were the boring survey of 10 boreholes, seismic survey of 2D (71 traverse lines, 180.105km) and 3D (1.5km{sup 2}), VSP (6 holes (345 shots)) and the low velocity band survey (2,072 shots). The geological structure of the area presented the syncline structure with a gentle line associated with foldings and a number of faults and was classified into the medium class or the class of a little complication in the Chinese standard. The number of the faults confirmed in this exploration totaled 57. Coal reserves by coal seam were 157.22 million tons at No. 5 seam and 102.57 million tons at No. 1 seam. The total amount of the two seams was 79.1% of the total coal amount in all area. The coal quality of Nos. 1 and 5 was brown coal - flame coal in the Chinese classification, and subbituminous coal B - subbituminous coal C in the ASTM classification. The coal, however, cannot be used for process raw coal. There is a technical potentiality of the fixed bed pressurized gasification. (NEDO)

  5. Optimization of dynamic source depth for seismic surveys. Part 7; Dynamite shingen no hasshin shindo no saitekika ni tsuite (hyoso kozo no suitei (kusssetsuho jishin tansa oyobi denki denjiho tansa)). 7

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, H; Murayama, R; Mitsuhata, Y; Ishikawa, H [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1996-05-01

    For the improvement of quality of data collected by reflection aided seismic exploration using dynamite as the seismic source, information has to be collected about the surface layer structure before the charge depth is determined. For this purpose, refraction, electric, and electromagnetic exploration methods were tried. In the refraction method, an impactor was used as the seismic source. In the records, the surface wave prevails because vibration was generated on the surface. Analysis was made by the use of the initial travel time tomography. In the electric exploration, a double pole array was used to measure resistivity. The measured data was subjected to a fully automatic inversion for analysis. As the result, it was disclosed that it was useful to know the deep-level structure directly by use of tomographic methods in refraction seismic exploration so as to find the optimum charge level. Furthermore, about the electric and electromagnetic exploration techniques, it was found that these methods can be applied making use of resistivity to the evaluation of groundwater saturation. 7 refs., 5 figs., 3 tabs.

  6. Convenient method for estimating underground s-wave velocity structure utilizing horizontal and vertical components microtremor spectral ratio; Bido no suiheido/jogedo supekutoru hi wo riyoshita kan`i chika s ha sokudo kozo suiteiho

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H; Yoshioka, M; Saito, T [Iwate University, Iwate (Japan). Faculty of Engineering

    1996-05-01

    Studies were conducted about the method of estimating the underground S-wave velocity structure by inversion making use of the horizontal/vertical motion spectral ratio of microtremors. For this purpose, a dynamo-electric velocity type seismograph was used, capable of processing the east-west, north-south, and vertical components integratedly. For the purpose of sampling the Rayleigh wave spectral ratio, one out of all the azimuths was chosen, whose horizontal motion had a high Fourier frequency component coherency with the vertical motions. For the estimation of the underground S-wave velocity structure, parameters (P-wave velocity, S-wave velocity, density, and layer thickness) were determined from the minimum residual sum of squares involving the observed microtremor spectral ratio and the theoretical value calculated by use of a model structure. The known boring data was utilized for the study of the S-wave velocity in the top layer, and it was determined using an S-wave velocity estimation formula for the Morioka area constructed using the N-value, depth, and geological classification. It was found that the optimum S-wave velocity structure even below the top layer well reflects the S-wave velocity obtained by the estimation formula. 5 refs., 6 figs.

  7. Estimation of shallow ground structure using short-period microtremors array observation. Results in Morioka area; Tanshuki bido no array kansoku ni yoru senbu chika kozo no suitei. Moriokashiiki ni okeru kekka

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H; Obuchi, T; Saito, T; Iwamoto, K [Iwate University, Iwate (Japan). Faculty of Engineering; Yoshida, Y [OYO Corp., Tokyo (Japan)

    1996-05-01

    The velocity structure in the shallow ground structure was evaluated by observing microtremors of 1-10Hz in the Morioka City area. Plural wave sections free of vehicle noises or the like were selected out of the collected microtremor records, and the Fourier spectrum and coherence were calculated. Records sufficiently supporting the correlation between seismographs were chosen for the analysis. The phase velocity was calculated for each observation spot from plural array records by use of the F-K spectrum. The underground velocity structure was estimated by the inversion process using the matrix method. In this method, an early model was built on the basis of the observed phase velocity and the optimum underground velocity structure was determined by alternately performing two inversion processes: one for the case wherein the S-wave velocity is the sole parameter and the other for the case wherein the layer thickness is the sole parameter. As the result, a shallow underground velocity structure, which has good agreement with the available boring data in the Morioka City area, was successfully estimated, verifying the validity of this method. 4 refs., 7 figs.

  8. On the fault system and basement structure in and around the epicentral region of the 1995 Hyogo-ken Nanbu earthquake; 1995 nen Hyogoken nanbu jishin shingen shuhen no danso kiso kozo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Yokokura, T; Kano, N; Yamaguchi, K; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan); Ikawa, T; Ota, Y; Kawanaka, T [Japex Jeoscience Institute, Tokyo (Japan)

    1996-05-01

    A reflection elastic wave seismic survey was carried out as part of the emergency survey of active faults in relation with the Hyogo-ken Nanbu Earthquake. This paper presents an interim report on the survey covering a wide area with deep structure as the survey object. The paper mentions that processing the survey data has been nearly completed, and is in the stage of making analyses and interpretations of the result of the processing, and that the survey was an attempt of making a unified survey over land areas, shallow sea areas, and seas by setting twelve traverse lines in and around the epicenter region. The paper also introduces briefly what has been found on hypocenters used, vibration receivers, vibration intervals, and CPD intervals, and on shapes of faults, particularly the continuity (the relationship of the Ashiya fault, Koyo fault and Osaka bay fault with the above two faults, branching of the Osaka bay fault, faults between the Wada promontory fault, Awaji Island and the Osaka bay fault, the fault off the east coast at the central part of Awaji Island, the Shichiku fault on the west coast of Awaji Island, and the basement fault). Mention is given also on the basement structure chart of the Osaka bay prepared preliminarily for the purpose of reference. 2 figs.

  9. Fiscal 1999 geothermal development promotion survey. Structural boring survey work and analysis report (No.B-6 - Tsujinodake area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho (No.B-6 Tsujinodake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    Cuttings from bores N11-TD-2 and N11-TD-3 drilled for the purpose of confirming the existence of geothermal resources in the Tsujinodake area were examined and tested, and the results of temperature logging, electrical logging, and water injection tests carried out during the structural boring work were analyzed. Activities were conducted in the four fields of (1) test boring work, (2) survey and measurement, (3) core cutting examination, and (4) comprehensive analysis. In bore N11-TD-2 positioned in the northern part of Tsujinodake, a sharp temperature rise was detected in the clay converted alteration zone between 200m above sea level and 200m below sea level. A high temperature of 215 degrees C was recorded at 200m below sea level, and it was found that high temperature geothermal water was in reserve at the bottom of the clay converted alteration zone between 100m above sea level and 200m below sea level. In bore N11-TD-3 in the southern wall of the Ata caldera, a convection type low temperature profile was observed at a shallow level and low temperature convection of underground water was detected there. (NEDO)

  10. FY 1997 report on the study on the formation condition of hetero-structure of single-crystalline semiconductor thin films; 1997 nendo chosa hokokusho (tankessho no handotai usumaku hetero kozo no keisei joken ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Since ion implantation causes material degradation by formation of crystalline defects, and hydrogen embrittlement deteriorates material strength, reduction of such defects has been positively studied. Study was made on a new active application of hydrogen separation into ion implantation defects. After H ion implantation of a proper depth into single-crystalline Si and SiC and successive annealing, single-crystalline films of sub-micron to several micron thick were obtained by hydrogen-induced delamination at the implantation depth due to hydrogen embrittlement in crystalline defects. The implantation depth is dependent on implantation energy. H atom forms (111) face defect through connection with dangling bond of crystalline defects. This crystal face defect forms a delamination plane through (100) face cleavage. This hydrogen embrittlement delamination by ion implantation is applicable to production of light-weight high-efficiency single-crystalline Si solar cells, and large single-crystalline SiC wafers as new resource saving process. 33 refs., 19 figs., 2 tabs.

  11. Report on the FY 1992 basic survey for industrialization related to the survey of overseas geological structure (Embalut West area, Indonesia); 1996 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa hokokusho (Indonesia Embalut nishi chiku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    The paper reported the FY 1992 basic survey for the coal mine development/industrialization in the Embalut West area of Indonesia. The geological structure in the survey area is under the Loa Haur Syncline which lies approximately north and south to the west of the area, and is regarded as the stabilized structure having no faults. The three beams from the upper part, S14, S13 and S12, are assumed to be the coal seams to be drilled. The average seam thickness is 1.17, 2.35 and 3.09m, respectively, and the continuity is good. In S14 beam, which is thin, it is difficult to mine coal using equipment. The theoretical minable reserve of the three coal seams is 18,859,000 tons. The recoverable coal reserve is 12,258,000 tons at a mining recovery of 65%. In case of annual production of 0.4 million tons, it is possible to mine more than 30 years. The coal is classified into a subbituminous coal-brown coal rank of the JIS coal classification. It is high in water content and medium in heating value, but is an environmental protection type with low ash and low sulfur content. In the case of mines in the Mahakam River basin, barge transport is indispensable. For sea transportation, the following should be studied in the light of the international price competition: reinforcement of shipping facilities on Mahakam River, increase in barge size, joint use of Balikpapan Coal Center, etc. (NEDO)

  12. Report on the FY 1998 geological structure survey. North Hay Gulch area, State of Colorado, the U.S.; 1998 nendo kaigaitan kaihatsu kanosei chosa hojo jigyo chishitsu kozo chosa hokokusho. Beikoku Colorado shu North Hay Gulch chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    Test boring at 21 places and core sampling were conducted during September-November 1998 along the ridge to the west of Hay Gulch and in the direction crossing the northwest of the drainage canal and National King Coal Mine (NKC coal mine). It was found that A layer which NKC coal mine is now drilling is the upper part of A coal seam where the seam bifurcates. The boundary to the west of the thick A coal seam is not clear, and there is a possibility that more reserve from the thick coal seam and single seam exists toward Cherry Creek. In the existing coal drilling area, the lower A seam existing under the upper A seam becomes thin rapidly, and the seam thickness becomes less than 1 foot. The average thickness of thick coal seams is 9.9 feet, and the area is 780 acres along the ridge. The upper A coal seam except the above is 5.5 feet in average seam thickness and 910 acres in area. The reserve is 23 million tons. As to the quality of thick coal seam, the average heating value is 7,089 kcal/kg, sulfur content 0.68%, and ash content 7.50%. As coal drilling conditions, the same level as or higher than those of NKC coal mine is expected. (NEDO)

  13. FY 1999 report on the results of the research cooperative project on the research cooperation in promotion of reforming the structure of the Asian economy; 1999 nendo Asia keizai kozo kaikaku sokushin kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    This project aims at making the best possible of vitality of private companies in Asia, producing the technical results which directly connect to commercialization in a short term, and leading them to reinforcement of developmental ability of their own technologies in the country. In the first fiscal year, eight projects were carried out in five ASEAN countries, and the developmental results with high potential of commercialization were obtained. The names of project are as follows: 1) development of Thai material type seasoning (Thailand), 2) development of electronic ceramics sintering technology by the domestic production (Thailand), 3) study of small-/medium-scale activated coal production technology for depopulated areas in Indonesia (Indonesia), 4) development of a fiber material procurement supply chain management system connecting among Asian countries by Web, 5) development of large plastic formed products adopting gas injection blow molding method (The Philippines), 6) joint R and D on the increase in power transmission capacity using the existing overhead transmission line in Malaysia, 7) development of local site application type asbesto substituting construction materials (Vietnam), 8) low temperature storing technology for Japanese species rice produced in Vietnam (Vietnam). All the projects were proposed by Japanese companies. (NEDO)

  14. Joint stiffness identification of body structure using neural network. Jointed part composed of 2 beams; Neural network ni yoru shatai kozo no ketsugo gosei dotei. Buzai 2 hon kara naru ketsugobu no baai

    Energy Technology Data Exchange (ETDEWEB)

    Okabe, A; Tomioka, N [Nihon University, Tokyo (Japan)

    1997-10-01

    The method to obtain a joint stiffness value from displacements of jointed part using hierarchical neural networks in case of a jointed part composed of two beams were proposed. First, the sample data of displacements of jointed part vs. joint stiffness are prepared as learned data. Second, the relations between displacements of jointed part and joint stiffness are constructed from these learned data using a hierarchical neural networks. It was found that the value of joint stiffness can be obtained from displacement of jointed part by the trained neural network. 4 refs., 9 figs., 2 tabs.

  15. Report for fiscal 1998 on basic commercialization survey related to geological structure surveys in overseas countries (Manguerra, the Philippines); 1998 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Philippines Manguerra) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Commercialization survey was performed on the mines in the Manguerra district in the Philippines by means of geological structure surveys. The site surveys included geological and test drilling surveys, and those on conditions for developing underground mining mines, and infrastructures. The geological survey area spread out about 5 km{sup 2}, two test wells were drilled (to depths of 330 m and 290 m), trench survey was performed on 58 locations, and coal sample collection and analysis were carried out on eight locations. Furthermore, surveys were extended to the Manguerra mine operating status, on-the-ground facilities, roads for transportation, marketing, and related laws and regulations. As a result of the surveys, the Manguerra district was suggested of frequent sea water inundation into the coal field, leading to a view that the district is unstable from the viewpoint of development of coal beds. However, samples collected from the existing mining area indicated to have less water content and ash and high calorific power. The coal has high product value. The result of coal quantity calculation indicated 320122 tons as the total of defined and estimated quantity. The great depth mining plan was prepared from the viewpoints of actual yield, productivity, safety aspects, technological enhancement, and suppression of additional investments to minimum. (NEDO)

  16. Fiscal 1999 geothermal development promotion survey report. Structural boring survey work and analysis (No. B-5 - Musadake region); 1999 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho - No. B-5 Musadake chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    For geothermal development in the Musadake region, Shibetsu-gun, Hokkaido, structural boring was carried out and boreholes were inspected. In the structural boring survey, borehole N11-MD-3 was drilled as deep as 2,001.18 m, and borehole N11-MD-4 2001.44 m. Performed or tested for each of the two boreholes were temperature logging, electrical logging, temperature recovery, reinjection, core cutting examination, and so forth. The result of the temperature logging shows that temperature rise is slower at levels deeper than 1280 m in borehole N11-MD-3, with the maximum temperature marking 274 degrees C, and, in borehole N11-MD-4, the maximum temperature is 198 degrees C. No reinjection test is carried out because the ground pressure is too high to allow the replacement of the borehole content with fresh water. Analysis results lead to a conclusion that the hot fluid in this region originates in fossil seawater and in meteoric water, the latter arriving after a long-term permeation process, heated by thermal conduction to 270 degrees C or higher. It is inferred that the geothermal fluid flows in a fissure in the vicinity of the Musadake/Mt. Shitabanupuri fault and a fault orthogonally crossing the said fault for the formation of a high-temperature geothermal storage. (NEDO)

  17. FY 1999 Report on overseas geological structure surveys. Joint Japan-China Yu Xian exploitation project (Attachments); 1999 nendo kaigai chishitsu kozo nado chosa futai shiryo. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This reports provides the attachments for the report JN0041264. The contents include (1) minutes of the fourth steering committee, (2) technical reports presented to the fourth steering committee (I: report on FY 1998 joint exploitation works, and II: report on FY 1999 joint exploitation works), (3) minutes of the fifth steering committee, and (4) technical reports presented to the fifth steering committee (I: report on FY 1999 joint exploitation works, and II: report on planned FY 2000 joint exploitation works). The item (1) includes approval of the reports on FY 1998 and 1999 joint exploitation works. The item (2)-I report includes seismic exploitation test works, observation work results and quality evaluation thereof; drilling exploitation work results, quality evaluation thereof, exploitation results and evaluation thereof; exploitation results and evaluation thereof; and proposals. The item (2)-II report includes seismic exploitation, drilling exploitation, and man-hours of the workers from the both countries. The item (3) includes approval of the reports on FY 1999 joint exploitation works and planned FY 2000 joint exploitation works. The (4)-I report includes seismic exploitation work results and evaluation thereof, seismic exploitation test works, drilling exploitation work results, quality evaluation thereof, exploitation results and evaluation thereof, and proposals for the future works. The (4)-II report includes seismic and drilling exploitation plans, and numbers and periods of the workers from the both countries. (NEDO)

  18. Report on the FY 1993 basic survey for industrialization related to the survey of overseas geological structure (Tebulan East area, Malaysia); 1993 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Malaysia Tebulan higashi chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The survey was conducted based on 'Scope of work for detailed coal exploration in the Tebulan East block of the Merit Pila coal field, Sarawak, Malaysia' concluded on June 19, 1993 between NEDO and Global Mineral which owns the mining right. The field survey was for the geological survey, survey of conditions of open pit mining, and infrastructure survey. The confirmed/estimated coal amount totaled 22,65 million tons in 4 coal seams. The all sulfur content is low, approximately 0.12%. The heating value is 5,820 kcal/kg. As to the infrastructure, various conditions are good for transportation, shipping facilities, etc. from mine site to truck transport/barge transport/external route shipping. The drilling was planned to be made by open pit mining by the truck and shovel system, and the scale of the planned production was 0.3 million tons. The ash is low in amount, and there was no coal preparation. Clean coal is produced by crushing, sieving and washing. Attached were the borehole log (JN9940782), route map, and trench sketch (JN9940783). (NEDO)

  19. FY 1998 Report on development project of structural residence of the next generation. Attachment 4. Frame analysis system manual; 1998 nendo jisedai kozo jutaku kaihatsu jigyo shiryohen. 4. Kako kaiseki system manual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Attachment 4 of the FY 1998 report on development project of structural residence of the next generation describes the frame analysis system manual. NAPISOS is a program for analyzing static and dynamic responses of three-dimensional structures. The dynamic response is calculated by numerical integration in the time region. Dynamic load can handle dynamic exciting force, uniform seismic input and forced displacement at a node, and analyze linear elasticity and non-linear properties. The static load can handle nodal force, static seismic coefficient and forced displacement at a node, and analyze linear elasticity and non-linear properties. The static analysis also can perform analysis based on the time history response displacement method as the special case. The program implementation procedures fall into 4 general steps; first: inputting/processing of structural data, second: eigen value analysis or equivalent nodal force calculation, third: response calculation by direct integration, preparation of equivalent damping matrix or pre-stress analysis, and fourth: outputting the results. The input data related to control, structure and load are also described. (NEDO)

  20. Investigations in fiscal 1986 on promotion of geothermal development. Part 2. Report on precision structural test well drilling and investigation works in Otaki area; 1986 nendo chinetsu kaihatsu sokushin chosa hokokusho. 2. Otaki chiiki seimitsu kozo shisui oyobi chosa koji

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-09-01

    With an objective of promotion of geothermal development in the Otaki area in Nagano Prefecture, precision structural test well drilling and investigation works have been carried out, and the result thereof reported. The investigated area is an inclined land with an area of 70 km{sup 2} at altitudes of 1,000 to 2,000 m in the southern foot of the Mitake volcano having Otaki River as the southern border. The investigation has performed during the period from March 2 to September 30, 1987 the drilling of the N61-OT-5 test well hole (depth of 502.0 m), temperature logging, temperature restoration test, water injection test, and core test. The result of the investigation may be summarized as follows: existence of the stratigraphic succession as predicted by ground surface investigation, and existence of the Mesozoic and Palaeozoic strata of the Mino belt were verified; the Mesozoic and Palaeozoic strata of the Mino belt being the base bed have only small cracks, and very little alteration can be identified; X-ray diffraction of powder from test drilled cores recognized very little minerals altered by hot water; and the temperature logging and temperature restoration test identified no temperature indication that clearly indicates existence of heat sources. As a conclusion, there is no alteration due to hot water down to 500 m below the surface in the vicinity of the investigation well, and the possibility of a geothermal reservoir to exist is extremely low. (NEDO)

  1. Research and development of photovoltaic power system. Study on structural defects in silicon-based amorphous materials; Taiyoko hatsuden system no kenkyu kaihatsu. Amorphous silicon kei zairyo no kozo kekkan ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, T [Kanazawa University, Ishikawa (Japan). Faculty of Engineering

    1994-12-01

    Described herein are the results of the FY1994 research program for structural defects of silicon-based amorphous materials for solar cells. The study on light generation defects of the a-Si:H system and rejuvenation process by annealing establishes the effects of light irradiation time on changed neutral dangling bond density as a result of light irradiation at varying temperature of 77K, room temperature and 393K. The study on annealing to rejuvenate light generation defects of various types of a-Si-H systems establishes the activation energy distribution with respect to annealing to remove light-induced defects, showing that hydrogen affects the distribution of light-induced defects. The study on decaying process of light-induced ESR for undoped and N-doped a-Si:H systems observes the decaying process of light-induced ESR, after light is cut off, extending for a period of several seconds to several hours at 77K for the a-Si-H systems containing N in a range from 0 to 12at%. The other results presented are space distribution of neutral defects of light-irradiated a-Si-H systems, and rejuvenation process of light-induced spin for the a-Si(1-x)N(x):H composition. 6 figs.

  2. FY 1974 Report on results of Sunshine Project. Research and development of methods for wide-area thermal structure exploitation; 1974 nendo koiki netsu kozo chosaho no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-28

    The project of (research and development of methods for wide-area thermal structure exploitation) is to pursue (1) development of heat flow rate analyzers, and researches on the methods for measurement/analysis of heat flow rates, (2) researches on geological thermometers with the cores collected from test bores as the samples, (3) observation/analysis of microearthquakes, and application of the results to the geothermal structure exploitation, and (4) development, on a trial basis, small, light air drilling machines. The method for clearly elucidating thermal structures has not been well established. Therefore, a test bore was drilled to measure temperature and collect the core samples in the wide-area geothermal district at Kita Yahata-daira as the model district, for measurement of heat flows, and analysis of the cores to estimate temperature at which they are formed. Microearthquakes, which frequently occur in geothermal areas, are also observed for extended periods. This project of (research and development of methods for wide-area thermal structure exploitation) is aimed at, based on the above efforts, to estimate/elucidate depth of thermal sources by the geological, geophysical and geochemical studies, relationships between geological structures and high-temperature zones, geothermal propagation structures, and geothermal reserves. This report summarizes the R and D results in the initial year of the 6-year plan. (NEDO)

  3. Investigation on the dynamic response and strength of very long floating structures by beam modeling on an elastic foundation; Dansei shishojo no hari model ni yoru chodai futai kozo no doteki tawami kyodo tokusei ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsubogo, T.; Okada, H. [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering

    1997-08-01

    A very large floating structure was replaced with the beam on an elastic foundation to examine the response characteristics in waves. Another evidence was regularly and numerically given for the basic characteristics of a very large floating body Suzuki found. New information was also obtained. The frequency response is mainly classified into a wave number control area and proper frequency control area when buoyancy elasticity exists. When the buoyancy structure is long and flexible, the proper frequency becomes continuous and the frequency control area becomes a resonance area. In the wave number control area, the Suzuki`s characteristic wave number becomes a control parameter, and various characteristic values are indicated by characteristic wave numbers. The response in the wave number control area becomes quasi-static when the distribution mass of buoyancy is fully small. The design in which the distribution mass of buoyancy is fully large must be avoided. In the displacement amplitude, the mass on the free end is severest. The proper frequency of vertical vibration relatively moves to the high-frequency side when buoyancy is considered as an elastic foundation. Attention must be thus paid to the proper frequency of vibration on the horizontal surface. 9 refs., 12 figs., 3 tabs.

  4. Fiscal 1998 overseas geological structure survey. Japan-China joint coal survey Mei-Xian project; 1998 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Mei-Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Japan-China joint coal survey was made through seismic prospecting by Japanese group and drilling prospecting by Chinese group. Mei-Xian mine property includes coal seams of the Jurassic period, and is covered with the quaternary period stratum without any coal seam. The base of the quaternary period stratum exists at depth of 50-400m, while the coal seams at depth of 300-700m. Among 11 existing seams, the 1st and 5th seams are main objects for prospecting. The 5th seam of 0.2-8.96m (2.95m in average) thick is the most expected important one, distributing all over the mine property. The 5th seam also has branch seams spreading over 2.5km from east to west and 1.2km from south to north in the center part of the mine property. The 1st seam of 0-8.62m (2.90m in average) thick is most thick in the south part of the mine property. The theoretical amount of coal deposits in the whole coal seam is estimated to be nearly 290,000,000t by Chinese group (nearly 50% of it in the 5th seam). That is also estimated to be nearly 346,000,000t by Japanese group (155,000,000t in the 5th seam). Both 1st and 5th seams are composed of sub-bituminous coal. (NEDO)

  5. Thermal structure of east and Southeast Asia. Comparison of results of Curie point depth analysis and heat flow data; Totonan Asia chiiki no ondo kozo. Curie ten shindo kaiseki kekka to chikaku netsu ryuryo tono hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, A; Okubo, Y; Matsubayashi, O [Geological Survey of Japan, Tsukuba (Japan)

    1997-10-22

    This paper describes the distribution of Curie point depth and its characteristics determined from the spectral analysis of magnetic anomaly data in East and Southeast Asia. It also describes relationships between the Curie point depth and the other geophysical information such as topography, heat flow data and tectonics. The Curie point depths are shallower than about 10 km at volcanic and geothermal areas, between 15 and 25 km at island arcs and back arc rifts, deeper than 20 km at continents, and deeper than 30 km at trenches. The Curie point depth (Dc) estimated from the heat flow data can be expressed by Dc=k{theta}c/q where k is thermal conductivity, q is heat flow, and {theta}c is Curie point. Based on the Curie point depths obtained from Curie point depth analysis in the cross section of northeast Japan and the averaged values of heat flow at individual points, they are distributed along a line of k{theta}c=1500[Wm{sup -1}]. Values of k{theta}c are small near the axis of Japan trench and large in the northeast Japan. It is considered that local anomalies can not be grasped from the spectral analysis. 21 refs., 3 figs.

  6. Distribution of strong ground motion from uppermost crustal structure. Comparison with disaster from the Hyogo-ken Nanbu Earthquake; Yaya fukai chika kozo no henka ni yoru kyoshindo bunpu. Hyogoken nanbu jishin ni yoru higai bunpu tono hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Z; Okubo, R [Kawasaki Geological Engineering Co. Ltd., Tokyo (Japan)

    1997-10-22

    It was intended to elucidate characteristics of distribution of damages caused by an earthquake which occurs directly below an urban area. Therefore, numerical simulation using the pseudo-spectral method was performed on characteristics of seismic wave propagation in non-homogenous media composed of rock beds and sediment beds, and of seismic wave amplitudes on ground surface. The simulation has utilized information on underground structures disclosed by using the latest physical exploration method. The underground structure model assumed a two-dimensional model hypothesizing presence of upper, middle and lower beds in the Osaka bed group on granite, using as reference the information on S-wave velocity underground structure revealed by the microtremor exploration method. With an objective to elucidate characteristics of distribution of collapse ratio in the area from 8-chome, Okamoto, Higashinada Ward, Kobe City to 2-chome of Sakanasaki Minamicho, as damages suffered from the Hyogo-ken Nanbu Earthquake, a simulation has been performed varying the structure model based on the results derived by the microtremor exploration method and the reflection method. As a result, it was shown that the characteristics of the maximum amplitude distribution of displacement of ground surface, velocity and acceleration agree well with those of the collapse ratio distribution, and that the simulation using the pseudo-spectral method is an effective means to analyze the ground surface collapse ratio distribution. 5 refs., 3 figs.

  7. Characterization of subsurface structure at Soultz HDR field by the triaxial drill-bit VSP; Sanjiku drill bit VSP ho ni yoru Soultz HDR field no chika kozo suitei

    Energy Technology Data Exchange (ETDEWEB)

    Asanuma, H; Niitsuma, H; Liu, H [Tohoku University, Sendai (Japan); Baria, R

    1997-10-22

    Triaxial drill-bit VSP (vertical seismic profiling) method is applied to the Soultz HDR (hot dry rock) field, France, where an artificial reservoir is provided inside the bedrock, and the structure inside the rockbed is estimated. An elastic wave detector is installed in the rockbed in this field, and data are acquired having frequency components up to approximately 1kHz. The trajectory of particles due to excavation noise is analyzed, and it is found that the drill-bit is the primary source of noise during excavation and that the SV-wave dominates in the emitted noise. Estimating the subsurface structure aided by the principle of the triaxial drill-bit VSP method, the lower part is detected of the artificial reservoir formed by hydraulic fracturing. As is reported in this paper, when the principle of the subject VSP method is considered, it has to be said that it is quite difficult to employ this method to extensively estimate the subsurface structure on the basis of measurements of the inside of the rockbed. There is a plan for a future study of a technique for accurately and extensively estimating subsurface structures by use of a small number of sensors. 8 refs., 7 figs.

  8. Estimation of a subsurface structure by using shallow seismic engineering exploration system with multiple function (SWS); Takino danseiha tansa sochi (SWS) ni yoru senbu chika kozo tansa ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Y [Beijing Shuidian Research Institute of Geophysical Surveying, Beijing (China); Ling, S [Nihon Nessui Corp., Tokyo (Japan); Okada, H [Hokkaido University, Sapporo (Japan)

    1997-10-22

    The Beijing Shuidian Research Institute of Geophysical Surveying has performed ocean seismic exploration in the area where the Fujian Pingtan bridge was planned to be constructed. The elastic wave exploration device is of a multi-functional type. The device has functions of acquiring, processing and analyzing data in seismic exploration using the reflection method, and can visualize subsurface conditions at the same time as performing the exploration. The planned bridge building area spans over a sea area of about 3500 m long with water depths from several meters to 30 meters. The foundation bed consists of dacite lithologic tuff and granodiorite. The seal level varies from 4.0 m to 4.8 m between high and low tides. According to the result of other measurements, the elastic wave propagation velocities of the sea water were found from 1475 to 1485 m/s, and the elastic wave propagation velocities at the surface bed of the sea bottom were from 1550 to 1700 m/s. The exploration used a workboat which moves at a constant speed while maintaining the offset between a transmitting source and a receiving source constant, executing vibration transmitting, receiving and recording all on the sea. The result of the exploration revealed that neither obstacles such as sunken ships nor marks of occurrence of ocean bottom landslides were present. 1 ref., 5 figs.

  9. Study on deep crustal resistivity structure using wideband magnetotellurics. In the case of eastern part of Hokkaido, Japan; Kotaiiki MT ho wo mochiita shinbu chikakuhi teiko kozo no kenkyu. Hokkaido Tobu chiiki ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H; Tanimoto, K; Maeda, T; Nishida, Y [Hokkaido University, Sapporo (Japan); Takada, M; Tamura, M [Hokkaido University, Sapporo (Japan). Research Center of Earthquake Prediction; Ogawa, Y [Geological Survey of Japan, Tsukuba (Japan); Nagao, T [Tokai Univ., Tokyo (Japan)

    1997-10-22

    Wide-range MT (magnetotelluric) observation is conducted to collect knowledge of the middle and lower parts of the crust of the above-named region, about which but a little information is available, for comparison with information about Kurile islands arc tectonics. Three traverse lines crossing the Kurile islands roughly in the north-south direction and two lines running from east to west are used, with the observation stations totalling 48. The distance between observation stations is 7-8km on the Nijibetsu line, and approximately 15km on the Nakashibetsu and Akan lines. A very wide frequency range of 320-0.0005Hz is used for measuring, and these results in detection with success of resistivity structure details from shallow to deep layers in the crust. The collected data are analyzed, and it is estimated that the northern and central parts have a high-low-high three-layer structure while the southern part has a low-high two-layer structure. Since the data obtained at observation stations at the middle of the lines, in particular, have an extremely low apparent value of several ohm/m at about 1Kz in the absence of splits in the TM (transverse magnetic) and TE (transverse electric) modes, it is inferred that the low-resistivity layer is considerably thick and is distributed rather uniformly. 13 refs., 5 figs.

  10. Formation of porous carbon materials from phenol-formaldehyde resin and their adsorption characteristics; Fenoru/horumu arudehido jushi kara erareta takosei tanso zairyo no kogeki kozo to sono kyuchaku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Oda, H.; Tojo, R.; Nomura, A. [Kansai Univ., Osaka (Japan). Faculty of Engineering

    1997-05-15

    In this study, preparation of porous adsorbent with developed micro-pores and meso pores and open pores on the external surface is tried. Namely, PFR-sawdust activated carbon is produced by carbonizing the PFR-sawdust composite materials obtained by adding KOH-immersed wood powders in the preparation of phenol-formaldehyde resin(PFR). Additionally, as a comparative test, KOH is added directly into PFR and PFR-KOH activated carbon is prepared by carbonization. Simultaneously with the clarification of the difference of pore structure between said two kinds of activated carbons, a various kinds of adsorbing tests are carried out to evaluate the adsorbing effects thereof. PFR-KOH activated carbon having a high specific surface area of 3500 m{sup 2}/g and a large number of micro-pore and meso pores is extremely effective in absorption of gas phase while the yield and particle strength are low. PFR-sawdust has a specific surface area of 1500 m{sup 2}/g which is the same level of activated carbons on the market, but the yield thereof is twice as that of PFR-KOH. 9 refs., 5 figs., 3 tabs.

  11. Solubilization of meso-carbon microbeads by potassium- or dibutylzinc-promoted butylation and structural analysis of the butylated products; Mesocarbon microbeads no butyl ka ni yoru kayoka to erareta butyl kabutsu no kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Murata, S.; Zhang, Y.; Kidena, K.; Nomura, M. [Osaka University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    Tetrahydrofuran (THF) solubility and structure of the butylated products of meso-carbon microbeads (MCMB) were studied experimentally. In experiment, MCMB-A and MCMB-B obtained from two kinds of coal-tar pitch were used as specimens. MCMBs were butylated by BZ method using dibutylzinc-butyl iodide and KT method using K-butyl iodide-THF, and the butylated products were successfully obtained. The butylated products were investigated through THF solubility test, {sup 13}C-NMR measurement and gel permeation chromatography (GPC) measurement. As the experimental result, a BZ method produced the butylated products at a yield of nearly 170%, while a KT method produced them at a yield of nearly 130%. The THF solubility was estimated to be 89-97%. As the study result of molecular weight distributions by GPC measurement of solvent solubles, the molecular weight of raw material MCMB was estimated to be 590-770 in terms of polystyrene. 6 refs., 2 figs., 1 tab.

  12. Thermal relaxation of bituminous coal to improve donation ability of hydrogen radicals in flash pyrolysis; Sekitan kozo kanwa ni yoru suiso radical kyoyo noryoku no kojo wo mezashita netsubunkai mae shori

    Energy Technology Data Exchange (ETDEWEB)

    Mori, T.; Isoda, T.; Kusakabe, K.; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hayashi, J. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    In terms of coal conversion reaction, the behavior of bituminous coal heated beyond a glass transition point was examined on the basis of pyrolyzed products, and the effect of an increase in proton mobility on promotion of coal decomposition was evaluated. In experiment, after Illinois bituminous coal specimen was heated up to a specific temperature in N2 or He gas flow at a rate of 5K/min, the specimen was directly transferred to a pyrolyzer for instantaneous pyrolysis. As the experimental result, the glass transition temperature of the Illinois coal specimen was calculated to be 589K from a differential scanning calorimetry (DSC) profile. From the pyrolysis result of the Illinois coal specimen heated up to 623K, the char yield decreased by 3kg as compared with that of the original coal, while the tar yield increased by 4kg up to 27kg per 100kg of the original coal. This tar increase was larger than that of cooled coal. These results suggested that the donation of hydrogen radicals to coal fragments is improved with an increase in proton mobility. 4 refs., 4 figs., 1 tab.

  13. Fiscal 1999 geothermal energy development promotion survey. Report on survey of structural boring (No. B-7 Kuwanosawa area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho (No.B-7 Kuwanosawa chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    Borehole N11-KN-1 was digged and investigated for clarifying the geothermal structure of the Kuwanosawa area, with attention fully paid to the existing survey results. The hole is inclined, 1,802.30m deep in total, with a casing pipe installed down to the 1,101.76m level. Temperature was measured and electrical logging was performed at levels 410m, 1,110m, and 1,802.23m while the hole walls were still exposed bear. The maximum temperature of 161 degrees C was observed at the hole bottom, and the product of permeability - layer thickness transmission coefficient was described by 3.72 to 4.75 times 10{sup -1} darcy.m. The geothermal structures in presence in the south-western part of the survey area and along the Wasabizawa fault were made clear, and it was found that there exists no high-temperature water system in the vicinity of borehole N11-NK-1. As tasks for the future, it was proposed that a geothermal survey of the south-eastern part which includes borehole N57-YO-2 and a geochemical survey of fluids including hot spring water and surface be conducted. (NEDO)

  14. FY 1999 report on the results of the development of technology of super metal. Development of nano/amorphous structure control materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing the amount of energy consumption of transportation equipment such as automobiles, the development is made of innovative metal materials enabling the weight reduction of members relatively on the basis of simple chemical components and by making more substantial improvement of characteristics such as strength and toughness than in the existing metals. For it, the following R and D are conducted in which nano crystal structure and non-equilibrium phase structure such as amorphous are controlled to the limits: 1) particle micro-dispersion technology; 2) high speed super plastic formation technology; 3) high density energy utilization control technology; 4) control cooling technology. In 1), study was made of alloy components and effects of the creation process which are needed for achievement of the nano level of crystal grain. In 2), conditions of vapor deposition and production in high speed particle deposition method are optimally selected, and amorphous and nano crystal structures can easily be produced. In 3), high corrosion-resistant amorphous alloy bulk materials with 5mm thickness and 10mm diameter were successfully trially manufactured. In 4), a bulk amorphous specimen with 10mm outer diameter, 6mm inner diameter and 1mm thickness which was fabricated in the forging method indicated favorable magnetic properties. A method to make a specimen which is more stable is being studied. (NEDO)

  15. Fiscal 2000 survey of geological structures overseas. Exchange of engineers with Indonesia (Coal mining technology); 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) Indonesia

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Indonesia rich in coal resources consumed 70-million tons of coal in 1999, which covered 17% of its total energy demand. It is estimated that as much as 120-million tons will be produced in 2005, and it is expected that underground mining will increase. Under such circumstances, Indonesia strongly desires that Japan's underground mining technologies be transferred to Indonesia. For the transfer of technologies especially involving production control and management out of Japan's underground mining technologies, Japan dispatched engineers to Indonesia under a mining engineer exchange project, and received and trained Indonesian engineers. Under the engineer exchange project, five engineers were dispatched to Indonesia and gave lectures and on-site training in the period July 9 through August 5, 2000. Japan received seven engineers, who were given lectures and training at the Ikeshima mining field of Matsushima Coal Mining Company in the period November 12 through December 12, 2000. (NEDO)

  16. FY 2000 report on the survey of the overseas geological structure. Japan-China joint coal exploration - Yu Xian project; 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The geological survey was carried out which is needed for coal mine design in the Yu Xian coal mine area, Yu Xian coal field, Hebei province, China. The term of survey was 5 years from 1996 to 2000. Activities are mainly for seismic survey and boring survey. Japan was in charge of the seismic survey, and China in charge of the boring survey. Both attained the goal. The results of the activities were summed up in the following 7 items: 1) outline of the survey; 2) general investigation; 3) state of the exploration related materials/machinery; 4) field survey; 5) items of survey; 6) results of the survey; 7) conclusion. In 6), the geological analysis, coal quality survey and coal amount survey were conducted. In the geological analysis, analyzed were the succession of strata, geological structure, and the situation of existence of coal seams. In 7), the following were made clear: geological structure of the survey area, coal seam, coal quality, hydrological geology, other conditions of drilling technology, and coal amount. The coal amount was 328.34 million tons in a total of A/B/C class coals. The total coal amount of Nos. 1 and 5 coal seams was 259.79 million tons, which was 79.1% of the total coal amount in all area. The average thickness of Nos. 1 and 5 coal seams, which are the main minable coal seams, was 3.10m and 2.66m, respectively. (NEDO)

  17. On the calculation of scattered fields by 3-D structure in the time-domain electromagnetic (TDEM) method; Jikan ryoiki denjiho ni okeru sanjigen kozo kara no sanranba no keisan ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, Y [Geological Survey of Japan, Tsukuba (Japan); Saito, A; Oya, T [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan)

    1996-10-01

    This paper describes the calculation method of 3-D underground structures in TDME method which measures only field components. Recently, FDTD method was developed as calculation method in time domain difference calculus, and the forward analysis accuracy of 3-D fields was rapidly improved. The survey results using a large-scale loop (600m{times}360m) were numerically analyzed by FDTD method. 16 measuring lines were prepared in both X and Y directions, and measuring points were prepared on intersection points of the measuring lines. Since signal current is staircase one, step and impulse responses of the ground were determined by calculating magnetic field and its time differentiation. The rectangular body (120m{times}120m{times}100m) of 0.2S/m in conductivity (5 ohm m in resistivity) was installed 160m under the ground as 3-D resistivity anomaly. The ground of 0.01S/m (100 ohm m) was assumed. Time variation in horizontal magnetic field vector plot of impulse responses of the uniform ground could be observed. The position of the resistivity anomaly could be also determined from spacial differentiation of magnetic field of grid pattern measuring points. 1 ref., 6 figs.

  18. Fault-related-folding structures and reflection seismic sections. Study by seismic modeling and balanced cross section; Danso ga kaizaisuru shukyoku kozo no keitai to jishin tansa danmen. 2. Seismic modeling oyobi balanced cross section ni yoru study

    Energy Technology Data Exchange (ETDEWEB)

    Tamagawa, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    It occasionally happens that there exists a part where reflection near the thrust is not clearly observed in a thrust zone seismic survey cross section. For the effective interpretation of such an occurrence, the use of geological structures as well as the reflected pattern is effective. When the velocity structures for a fold structure having a listric fault caused anticline (unidirectionally inclined with a backlimb, without a forelimb) and for a fault propagation fold are involved, a wrong interpretation may be made since they look alike in reflection wave pattern despite their difference in geological structure. In the concept of balanced cross section, a check is performed, when the stratum after deformation is recovered to the time of deposition, as to whether the geologic stratum area is conserved without excess or shortage. An excess or shortage occurs if there is an error in the model, and this shows that the fault surface or fold structure is not correctly reflected. Positive application of geological knowledge is required in the processing and interpreting of data from a seismic survey. 6 refs., 6 figs.

  19. Fault-related-folding structure and reflection seismic sections. Construction of earth model using balanced cross section; Danso ga kaizaisuru shukyoku kozo no keitai to jishin tansa danmen. 1. Balanced cross section wo mochiita chika model no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Tamagawa, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    Pre-stacking depth migration treatment is studied for the estimation of the fold configuration from seismic survey cross sections. The estimation of a velocity structure is necessary for the execution of such treatment, and the utilization of structural-geological knowledge is required for its interpretation. The concept of balanced cross section in relation to the fault-bend fold constructs a stratum structure model under conditions that the deformation during fold and fault formation is a planar strain, that there is no change in volume due to deformation, and that a fold is a parallel fold. In addition to the above geometric and kinetic approach, there is another fold formation process simulation model using a Newtonian fluid for study from the viewpoint of dynamics. This simulation stands on the presumption that the boundary contains a ramp that had been in presence before fold formation and that an incompressible viscous matter is mounted on the top surface. The viscous matter flows and deforms for the formation of an anticline on the ramp. Such enables the reproduction of a fault-bend fold formation process, and helpful discussion may be furthered on the dynamic aspect of this simulation. 5 refs., 4 figs.

  20. Estimation of subsurface structures in a Minami Noshiro 3D seismic survey region by seismic-array observations of microtremors; Minami Noshiro sanjigen jishin tansa kuikinai no hyoso kozo ni tsuite. Bido no array kansoku ni yoru suitei

    Energy Technology Data Exchange (ETDEWEB)

    Okada, H; Ling, S; Ishikawa, K [Hokkaido University, Sapporo (Japan); Tsuburaya, Y; Minegishi, M [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    Japan National Oil Corporation Technology Research Center has carried out experiments on the three-dimensional seismic survey method which is regarded as an effective means for petroleum exploration. The experiments were conducted at the Minami Noshiro area in Akita Prefecture. Seismometer arrays were developed in radii of 30 to 300 m at seven points in the three-dimensional seismic exploration region to observe microtremors. The purpose is to estimate S-wave velocities from the ground surface to the foundation by using surface waves included in microtremors. Estimation of the surface bed structure is also included in the purpose since this is indispensable in seismic exploration using the reflection method. This paper reports results of the microtremor observations and the estimation on S-wave velocities (microtremor exploration). One or two kinds of arrays with different sizes composed of seven observation points per area were developed to observe microtremors independently. The important point in the result obtained in the present experiments is that a low velocity bed suggesting existence of faults was estimated. It will be necessary to repeat experiments and observations in the future to verify whether this microtremor exploration method has that much of exploration capability. For the time being, however, interest is addressed to considerations on comparison with the result of 3D experiments using the reflection method. 4 refs., 7 figs.

  1. Estimation of underground structures in the Osaka-Kobe area by array-network observations of microtremors; Bido no array kansoku ni yoru Osaka-Hyogo chiiki no chika kozo no suitei

    Energy Technology Data Exchange (ETDEWEB)

    Okada, H; Ishikawa, K; Ling, S [Hokkaido University, Sapporo (Japan); Sasabe, K [Ministry of Construction, Tokyo (Japan)

    1997-05-27

    Microtremor observations have been carried out with an objective to estimate underground structures including the foundation depth in the Osaka-Kobe area which has been greatly damaged by the Hyogoken-nanbu earthquake in 1995. Different organizations have made seismic surveys and boring investigations in this area, by which elucidation has been made on the underground structures. The present observations are intended to identify S-wave velocity distribution in a wide area from the ground surface to the foundation, which is difficult to be verified by using conventional surveys and investigations. Methods to detect surface waves which are contained in microtremors include the frequency-wave number method (the F-K method) and the spatial autocorrelation method (the SPAC method). The SPAC method can estimate phase velocities of longer waves for the size of an array than with the F-K method, and is more advantageous in estimating ground structures at greater depths. S-wave velocity structure was estimated down to the foundation rocks existing in depths of about 0.5 to 2.0 km. For estimating the phase velocities in Raleigh waves, the SPAC method and the expanded spatial autocorrelation method were used. The underground structures thus derived showed a good agreement with the results of explorations using other methods. 8 figs., 1 tab.

  2. Relationship between surface structure of silicon containing steel and adhesion of hot dip galvanized coating; Si gan'yu koban no hyomen kozo to yoyu aen mekki micchakuseino kankei

    Energy Technology Data Exchange (ETDEWEB)

    Tsuchiya, Y.; Hashimoto, S.; Ishibashi, Y. [Kokan Keisoku K.K., Kawasaki (Japan); Inagaki, J. [NKK Corp., Tokyo (Japan); Fukuda, Y. [Shuibuoka University, Shizuoka (Japan)

    2000-06-01

    The surface of the annealed steel and the exfoliated interface of the coating for the hot dip galvanized Si containing steel sheets was characterized by using SEM (Scanning Electron Microscope), AES (Auger Electron Spectroscopy) and TEM (Transmission Electron Microscopy). The adhesion of the coatings have depended on the Si content of the steel. It have been found that MnSiO{sub 3} particles are formed at the surface of the annealed steels having high Si content and that two types of grain having different distribution of the oxide exist in the steels. Large oxide particles have been formed in one type of grain and small particles are formed in the other type of grain. The different type of Fe-Zn alloy are formed on two types of grains. It have been observed that the oxide particles exist at the interface of exfoliated coatings after the adhesion test for the steels with high Si content. The distribution of the oxide particles observed at the bottom of the exfoliated coating is quite similar to that of the surface oxide of the annealed steel. From these results, the exfoliation of the coating has initiated at the oxide particles of the steel surface that has been not reduced during the hot dip galvanizing. (author)

  3. Report on a commercialization fundamental investigation (in Batulicin Area, Indonesia) in relation to FY 1997 investigations on geological structures in overseas countries; 1997 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Indonesia Batulicin chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A fundamental coal mine development investigation was carried out in Batulicin Area, Kalimantan, the Republic of Indonesia. The investigation included ground surface surveys, preparation of topographical maps and geological maps, trial drilling investigation, physical logging, chemical analysis, and infrastructure investigation. The trial drilling investigation was intended to identify the existence conditions of coal beds and coal quality, and was performed by forming grids with about 500-meter interval, and using 21 trial drillings to depths of 104 to 240 meters for a total drilling length of 3463 meters. The physical logging included electric logging, radioactivity logging and pore size logging, and the trial drilling cores were subjected to chemical analysis. For infrastructures, investigations were carried out on necessity of modifying existing roads, privilege relationship, the current status of barge loading points, water depths, and land acquisition. The result of the investigation revealed that minable coal quantity in underground mining of the coal bed B would be 13.189 million tons, and that annual production of original coal at 733,000 tons would be possible by adopting a long-wall type mechanized coal mining system. 14 refs., 99 figs., 25 tabs.

  4. FY 1994 report on the survey of geothermal development promotion. Investigative construction and analysis for structural boring (No. A-1 - Haneyama area); 1994 nendo chinetsu kaihatsu sokushin chosa. Kozo shitsui chosakoji oyobi kaiseki hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-01

    For the contribution to elucidation of the geothermal structure in the Haneyama area, Oita Prefecture, the paper carried out the drilling of structural boring exploration wells, N6-HN-1 (1,605m) and N6-HN-2 (1,402m), and the well exploration. In the well exploration, the following were conducted: measurement of earth temperature, temperature recovery test, electrical log, simple water injection test, core/cutting observation, core test, powder X-ray diffraction analysis, physical property test, measurement of homogenization temperature of fluid inclusion, etc. In the temperature log and temperature recovery test, the terminal temperature at a 1,600m depth of N6-HN-1 well and at a 1,400m depth of N6-HN-2 well was 139.6 degrees C and 26.2 degrees C, respectively. The homogenization temperature of fluid inclusion was relatively higher, +70 degrees C to +100 degrees C, than that in the results of the temperature log, but was on the side of lower temperature, -30 degrees C to -100 degrees C, in a comparison with the saturated boiling curve of the earth surface and ground water level. Namely, it was thought that around the N6-HN-1 well, there used to exist the high temperature fluid of 250 degrees C or higher at the peak period of geothermal activities, but there only existed the geothermal water of approximately 140 degrees C at the present time. (NEDO)

  5. Fiscal 1998 geological survey overseas. Report on Tanjung Enim project for Japan-Indonesia joint coal exploration; 1998 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Indonesia sekitan kyodo tansa Tanjung Enim project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For disclosing stratigraphy and lithofacies and for clarifying the status of coal beds in the southern Arahan area (55km{sup 2}), South Sumatra, ground surface exploration, borehole drilling, borehole geophysical logging, and seismic reflection monitoring were carried out. The survey covered a rectangular area, 11km from east to west and 5km from north to south and 60m to 130m in elevation. In the ground surface exploration effort, trenching was performed at three spots in coal bed outcrops in an quasi-accurate survey with route gaps of roughly 1,200m. Ten boreholes were drilled. The deepest one was 282.20m deep and the shallowest one 117.80m deep, with the total drilled length measuring 1,643.70m. Seismic reflection monitoring was implemented using three traverse lines (two running north to south and one running from east to west), with the three lines measuring 10.92km in total. VSP (vertical seismic profiling) was carried for borehole ASN17 only. The findings are that there are four kinds of coal beds, that is, A2, B, C, and E spreading all over the area, that their thicknesses are estimated to be 12m, 18m, 7m, and 6-8m, respectively, and that coal beds A2, B, and C are packed into between 80m-deep and 150m-deep levels. (NEDO)

  6. Characteristic analysis on the deformation behaviour of shell-like lattice structures subjected to follower forces; Judo kaju wo ukeru kosa arch kozo no daihenkei kyodo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fukuchi, N.; Okada, K. [Kyushu University, Fukuoka (Japan); Fujii, M. [Namura Shipbuilding Co. Ltd., Osaka (Japan); Shiraki, M. [Toyota Motor Corp., Aichi (Japan)

    1998-09-04

    The deformation mechanisms of submerged shell-like lattice structures with membrane are in principle of a non-conservative nature since the follower type hydrostatic pressure. In the region of large deformations, especially in the case of geometrically deep shell-like lattice structures, the system could be much more accurately defined in a mono-clinically convected coordinate description than the conventional spatial description. Also, a complete analysis of a non-conservative system requires a criterion since the system can have multiple ranges of stability and instability involving buckling and snapping. This paper presents the development of the governing equations for the finite deformations of shell-like lattices defined in a mono-clincally convected coordinate description and applies the same to different cases of lattice deformations. The validity of the formulations is verified for finite deformation. The examples of some geometrically special shell-like lattice structures are presented as well to show the feasibility of the present formulation. 5 refs., 11 figs.

  7. X-ray diffraction study on microstructure of Li20-TeO2 glasses; Xsen kaisetsuho ni yoru Li{sub 2}O-TeO{sub 2} kei garasu no mikuro kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Iwadate, Y; Hattori, T; Nishiyama, S; Fukushima, K; Sugawara, Y [Chiba Univ. (Japan); Noda, K. [Japan Atomic Energy Research Inst., Tokyo (Japan)] Tatsumisuna, M. [Osaka Prefectural Univ., Sakai (Japan)] Umesaki, M. [Osaka Industrial Research Inst., Osaka (Japan)

    1998-07-10

    Li2O-TeO2 glasses attract attention because of unique properties such as high density, high refractive index, large dielectric constants and high infrared transmittance. The short range structures of two samples of Li2O-TeO2 glasses (15:85 mol% Li2O-TeO2 and 25:75 mol% Li2O-TeO2) were investigated by X-ray diffraction technique. Interpretation of the obtained radial distribution functions was performed on the basis of the strength comparison method. The following conclusions were obtained: Two types of Te-O bond lengths of 0.18nm and 0.20nm are found in TeO4 tetragonal bipyramid. As network forming units, the TeO4 tetragonal bipyramids and TeO3 trigonal bipyramids are observed. The TeO4 tetragonal bipyramid units are transformed into the TeO3 trigonal bipyramids through the transient species of polyhedral with non-bridging oxygen atoms with increasing content of Li2O. The lone pair of Te atom does not contribute to the formation of the glass network. 17 refs., 6 figs., 2 tabs.

  8. Borehole geophysics for delineating the geological structure in the Sakonishi prospect, the Hida area, Japan; Hida chiiki Sako nishi chiku ni okeru boring ko riyo butsuri tansa ni yoru chishitsu kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Katayama, H.; Hishida, H.; Yoshioka, K. [Metal Mining Agency of Japan, Tokyo (Japan)

    1997-05-27

    In order to discuss effectiveness of physical exploration in the Sakonishi prospect in the Hida area, physical exploration was carried out by utilizing bored wells. This area contains the Kamioka mine, one of the major base metal mines in Japan, where electrical exploration has been attempted several times in the past. No effective results have been obtained, however, because specific resistance contrast between mine beds and base rocks is too small, and the topography is too steep making site workability inferior. As part of the investigations on geological structures over wide areas, electrical logging (specific resistance and natural potential) was performed in fiscal 1995 and 1996 by utilizing the boreholes. Induced polarization logging was also conducted on the same boreholes. A traverse line on the ground with a length of 600 m and boreholes were used to execute specific resistance tomography. Clear extraction was possible on a fault structure which is thought related with limestone distribution and mine bed creation. However, it was not possible to identify upward continuity of zinc ores expected in the exploration. Because of not large a specific resistance contrast between zinc ores and base rocks, it is difficult to find mine bed locations only from the information on the specific resistance. 5 refs., 5 figs., 1 tab.

  9. Structural response analysis of very large floating structures in waves using one-dimensional finite element model; Ichijigen yugen yoso model ni yoru choogata futai no harochu kozo oto kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Fujikubo, M.; Yao, T.; Oida, H. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1996-12-31

    Formulation was made on a one-dimensional beam finite element which is effective in analyzing structural response of very large floating structures by modeling them on beams on an elastic foundation. This element allows strict solution of vibration response in the beams on the elastic foundation to be calculated efficiently for a case where mass and rigidity change in the longitudinal direction. This analysis method was used to analyze structural response of a large pontoon-type floating structure to investigate mass in the end part for the structural response and the effect of decay while passing the structure. With a pontoon-type floating structure, reduction in bends and bending stress in the end part of the floating structure is important in designing the structure. Reducing the mass in the end part is effective as a means to avoid resonance in these responses and reduce the responses. Increase in rigidity of a floating structure shifts the peak in quasi-static response to lower frequency side, and reduces response in resonance, hence it is advantageous for improving the response. Since incident waves decay while passing through the floating structure, response in the lower wave side decreases. The peak frequency in the quasi-static response also decreases at the end part of the structure in the upper wave side due to decay in wave force. 7 refs., 11 figs., 1 tab.

  10. Proceedings of the Spring Meeting of the Society of Naval Architects of Japan (1996). Part 2. Structure, materials, welding, construction, and design; Nihon zosen gakkai (1996 nen) shunki koen ronbun maezuri. 2. Kozo, zairyo, yosetsu, kosaku, sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    This is a proceedings of the Spring Meeting of the Society of Naval Architects of Japan made public on May 15 and 16, 1996. In the basic research, the following are included: Basic studies on computer aided concurrent engineering for hull structure design and piping design; Fundamental study on the new method to estimate vibration level on a ship; Flat plate approximation in the three-dimensional slamming; Development of new finite element by source method, etc. As to fracture and cracks, Equivalent CTOD concept based on the local approach and its application to fracture performance evaluation of welded joints; Fracture mechanical modeling of brittle crack propagation and arrest of steel; An evaluation method for ductile crack propagation in pre-strained plates; Multiple fatigue cracks propagating in a stiffened panel, etc. Relating to fatigue strength, Fatigue life estimation of welded joints of an aluminum alloy under superimposed random load waves; Study on unified fatigue strength assessment method for welded structure, etc.

  11. Fiscal 2000 survey report on overseas geological structure, etc. Project for exchanging experts - Exploration technology (Indonesia); 2000 nendo kaigai chishitsu kozo to chosa hokokusho. Gijutsusha koryu jigyo - Tansa gijutsu bunya (Indonesia)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the stabilization of coal supply/demand in the APEC (Asia-Pacific Economic Cooperation Conference) region and for the stable supply of coal to Japan, Japanese engineers and experts were dispatched to Indonesia, where coal production was remarkably increasing and efforts were being actively exerted to develop new coal mining fields, for training Indonesian specialists there, and Indonesian specialists were invited to Japan for training here. Japanese instructors on dispatch delivered lectures on coal geology, exploration, and exploitation at the human resource development center of Bandung City during the period July 20 through August 4, 2000, which was followed by a coal outcrop survey training session in the field. The trainees were from Kalimantan, Sumatra, Java, etc., and numbered 30. The trainees invited to Japan received lectures and training related to coal geology, exploration, and mining programs during the period October 19 through November 18, 2000, at the Geological Survey of Japan, Agency of Industrial Science and Technology, Ministry of International Trade and Industry; Matsushima Coal Mining Co., Ltd.; Enzan Plant, Tone Corporation; DIA Consultants Co., Ltd.; and Mitsubishi Materials Corporation. (NEDO)

  12. FY 1998 annual report on the survey on overseas geological structures. Project for exchanging engineers (coal mining technology area) (Vietnam); 1998 nendo kaigai chishitsu kozo nado chosaa. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) (Vietnam)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The project for exchanging engineers has been implemented, in order to improve production and managemental techniques of coal mining engineers in the Asia-Pacific region, promote smooth and efficient projects for surveying overseas geological structures, and facilitate stable supply of overseas coal to Japan. The FY 1998 project was concentrated on Vietnam, to which Japanese coal mining engineers were sent, and from which production management engineers were invited to Japan as trainees. The Japanese engineers sent to Vietnam educated the underground coal mining techniques. The Vietnamese management engineers invited were trained for, e.g., production management techniques (e.g., those for workplaces and organizations) in the Japanese mines, administrative management techniques, and techniques to improve safety and productivity in the mines. Coal Energy Center and Taiheiyo Mining's Kushiro Mine provided training facilities. (NEDO)

  13. Synthesis and structure of porous alumina precursors derived from n-alkylamine-AlCl3 system; Chokusa alkylamine-AlCl{sub 3} kei wo mochiiru takoshitsu alumina zenkutai no gosei to kozo

    Energy Technology Data Exchange (ETDEWEB)

    Yoshimura, M.; Machida, M.; Kijima, T. [Miyazaki Univ. (Japan)

    1998-06-01

    Alumina precursors have been prepared from AlCl3 by using n-alkylamines (C{sub n}H{sub 2n+1}NH2) as precipitant at pH 9.6 and pH 6.2, and the structure, composition, microstructure, and thermal decomposition behavior are investigated. The effects of the structure of the precursor on the decomposition behavior and on the surface area of porous alumina are also investigated. When alkylamines n{>=}6 are used, long periodicity phases are produced corresponding to larger than d=2.0nm spacing which can not be attributed to bayerite or pseudo-boehnite. Long periodicity phase is formed uniquely near the water content of about 50mass% (H2O/Al=4.5), and the spacing varies depending on the alkyl chainlength of amine. When the precipitate prepared at pH 6.2 is heated, water is desorbed at near 100degC, pseudo-baehnite phase is pyrolyzed at 300degC, and the precipitate changed into {gamma}-alumina at temperatures higher than 500degC. 16 refs., 9 figs.

  14. FY 1999 Report on overseas geological structure surveys. Joint Japan-China Yu Xian exploitation project; 1999 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project is based on the (agreement of the joint exploitation project for Yu Xian block in Yu Xian coal mine, Province of Hepei by Japan's NEDO and China's Coal Geological Bureau), signed on October 4, 1996. The joint project mainly comprises seismic exploitation and test drilling, Japan being mainly responsible for the former and China for the latter. The final report will be drawn jointly for the geological survey results necessary for designing coal mines. The Yu Xian block contains the Jurassic coal seams, which are covered by the Quaternary bed and not exposed to the surface. The Quaternary bed base is 50 to 400 m deep from the surface, and coal seams are 300 to 700 m deep also from the surface. A total of 11 coal seams are located in the Xiahuayuan strata as the coal-bearing strata. The first and fifth seams are most promising ones. In particular, the fifth seam is thick (0.2 to 6.91 m thick) and distributed throughout the block. It is estimated that 8 coal seams have a total coal quantity of approximately 346 million tons. (NEDO)

  15. Fiscal 1998 overseas geological structure survey report on the engineer interchange project (coal mine technology field), Indonesia; 1998 nendo kaigai chishitsu kozo nado chosa gijutsusha koryu jigyo (tanko gijutsu bun'ya), Indonesia hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at improvement of coal mining technology and productivity in Indonesia by Japanese production control technology and business management technology for underground coal mining, through interchange of coal engineers between Japan and Indonesia. This project is composed of the short- term and long-term dispatch project of engineers to Indonesia, and the training project of Indonesian engineers in Japan. In fiscal 1998, the short-term dispatch was made for the training in Indonesia on underground coal mine development (development planning, pit mouth selection, main gallery design, mining system selection, transport planning, ventilation planning, under-river mining, mine water proofing, drainage). The long-term dispatch was made for contact and negotiation with concerned Indonesian organizations, support of the training project, and collection of information on the trend of Indonesian economy and energy, and the present and trend of the coal industry for conducting smooth and effective engineer interchange. (NEDO)

  16. Report for fiscal 1999 on basic commercialization survey related to geological structure surveys in overseas countries (Kalewa area, Myanmar); 1999 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Myanmar Kalewa chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Commercialization survey was performed on the coal beds in the Kalewa area in the Union of Myanmar by means of geological structure surveys. The site surveys included on-the-ground survey, test drilling survey, sample collection and analysis, and infrastructure survey. The on-the-ground survey area spread out about 5.5 km{sup 2}, wherein nine test wells were drilled (for total distance of 2,046.74 m), and coal and rock sample collection and analysis were carried out on six samples. The infrastructure survey was performed on coal transporting roads, and barge loading planned points and facilities. As a result of the test drilling survey, existence of coal beds with thickness of 4 ft, 9 ft and 6ft was identified. Since the 9-ft bed in particular exists stably with inclination of 40 to 42 degrees over the whole subject area, it was made clear that the bed can be the object of mining as the main coal bed. The coal is the ordinary coal with such good qualities as ash content of 4.72%, total sulfur content of 0.22%, and total calorific power of 6,500 to 6,570 kcal/kg. The defined coal quantity for the 9-ft bed is four million tons, or 7.7 million tons in total if the estimated coal quantity is added. The quantity will amount to 15.3 million tons when those of the 4-ft and 6-ft beds are added. (NEDO)

  17. Proceedings of the Spring Meeting of the Society of Naval Architects of Japan (1996). Part 2. Structure, materials, welding, construction, and design; Nihon zosen gakkai (1996 nen) shunki koen ronbun maezuri. 2. Kozo, zairyo, yosetsu, kosaku, sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This is a proceedings of the Spring Meeting of the Society of Naval Architects of Japan made public on May 15 and 16, 1996. In the basic research, the following are included: Basic studies on computer aided concurrent engineering for hull structure design and piping design; Fundamental study on the new method to estimate vibration level on a ship; Flat plate approximation in the three-dimensional slamming; Development of new finite element by source method, etc. As to fracture and cracks, Equivalent CTOD concept based on the local approach and its application to fracture performance evaluation of welded joints; Fracture mechanical modeling of brittle crack propagation and arrest of steel; An evaluation method for ductile crack propagation in pre-strained plates; Multiple fatigue cracks propagating in a stiffened panel, etc. Relating to fatigue strength, Fatigue life estimation of welded joints of an aluminum alloy under superimposed random load waves; Study on unified fatigue strength assessment method for welded structure, etc.

  18. Structural response analysis of very large floating structures in waves using one-dimensional finite element model; Ichijigen yugen yoso model ni yoru choogata futai no harochu kozo oto kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Fujikubo, M; Yao, T; Oida, H [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1997-12-31

    Formulation was made on a one-dimensional beam finite element which is effective in analyzing structural response of very large floating structures by modeling them on beams on an elastic foundation. This element allows strict solution of vibration response in the beams on the elastic foundation to be calculated efficiently for a case where mass and rigidity change in the longitudinal direction. This analysis method was used to analyze structural response of a large pontoon-type floating structure to investigate mass in the end part for the structural response and the effect of decay while passing the structure. With a pontoon-type floating structure, reduction in bends and bending stress in the end part of the floating structure is important in designing the structure. Reducing the mass in the end part is effective as a means to avoid resonance in these responses and reduce the responses. Increase in rigidity of a floating structure shifts the peak in quasi-static response to lower frequency side, and reduces response in resonance, hence it is advantageous for improving the response. Since incident waves decay while passing through the floating structure, response in the lower wave side decreases. The peak frequency in the quasi-static response also decreases at the end part of the structure in the upper wave side due to decay in wave force. 7 refs., 11 figs., 1 tab.

  19. FY 1999 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (R and D of the intellectual material and structural systems); 1999 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (chiteki zairyo kozo system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 1999 results of the R and D project for development of intellectual materials and structural systems, where the fibrous or leafy sensor material or element (muscle) is integrated with a structure of an advanced material (skeleton) to process and control information (brain). The program for development of the health monitoring technologies develops the fine optical fiber (diameter: 40{mu}m), which is on a level with the conventional 125{mu}m-diameter fiber in strength and fatigue characteristics, for the high-performance sensor systems. The self-diagnosis of soundness, e.g., detection of impact loads and damages, is attempted using the fine optical fibers embedded in the composite structures. The program for active-adaptive control of smart structures investigates control of vibration and noise for beam structure elements, using the theoretical model developed for shape memory alloys. The vibration tests are conducted, where a distribution type sensor is used for active-adaptive control of soft structures, and the good results are produced. The program for development of actuator materials and elements produces high-strength, high-toughness PZT and PNN-PZT sheets of uniformly distributed thickness by the doctor blade method. (NEDO).

  20. FY 1993 research and development of the technology for controlling structures of functional composite members. R and D of advanced surface processing for methane-fueled aircraft engine members (Technology for controlling the microscopic structures of superhigh-temperature members); 1993 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). Chokoon buzai micro kozo seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Described herein are the results of the FY1993 research and development project, implemented for development of the technologies for modification of material surfaces and interfaces, with the objectives to develop the optimum members for methane-fueled aircraft engines. For R and D of multi-layered films with controlled microscopic structures, the tests are conducted for forming thin-film layers by, e.g., ion implantation, ion mixing and implantation of large quantities of ions as the surface controlling/modification techniques based on, e.g., ionic techniques. The tests are conducted for, e.g., chemical vapor-phase reaction evaporation and low-pressure plasma spraying as the technologies for forming multi-functional films of, e.g., high reliability and resistance to corrosion. For development of the technologies for controlling/compositing the microscopic structures, the tests are conducted for, e.g., selection of the matrix materials, and prevention/removal of defects by the chemical vapor-phase reaction penetration treatment effected for extended periods. For development of the technologies for evaluation of the characteristics under superhigh-temperature environments, the tests are conducted to investigate the mechanical characteristics of isotropically uniform metallic materials under multi-dimensional stresses and evaluation thereof, and mechanical and thermal characteristics of carbon-fiber-reinforced carbon composites and evaluation thereof. (NEDO)

  1. FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Ocean survey and development of evaluation technology for CO2 sequestration ability); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Assuming the melting and sequestration of CO2 at the intermediate depth of the sea area around Japan, study of evaluation technology of CO2 sequestration ability in ocean was studied, and the FY 1999 results were summed up. In the ocean survey, survey was conducted by ship (No.2 Hakurei-maru) mainly at typical observation points and traverse lines of long. 147 E and long. 155 E. In the survey, the following data were acquired: data on seawater density and chemical tracer, data on release of intermediate-depth/independent buoys, concentration distribution of carbonic acid base substances/nutrient salts/chlorophyll, data on the existing amount of marine organisms and primary production speed measurement experiment, data on experiment on CO2 on-board exposure to organisms in the intermediate depth of ocean, etc. In the measurement/analysis of the sediment particle flux amount, sediment traps were installed/recovered. Further, for the purpose of measuring the neutralizing effect of calcium carbonate, operation test on CaCO{sub 3} melting experimental equipment was conducted in the actual sea area. In the development of a model for evaluation of CO2 sequestration ability, carried out were the improvement of the model using the inverse method, study of the estimated accuracy using the ocean observation data, etc. (NEDO)

  2. FY 2000 report on the results of the R and D of the prediction technology for environmental effects of CO2 ocean sequestration. Ocean survey and development of the assessment technology for capacity of CO2 sequestration; 2000 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Assuming the dissolution/sequestration of CO2 at the medium-depth sea area around Japan (depth: 1,000-2,000m), the development was being proceeded with of the assessment technology for capacity of CO2 ocean sequestration and the prediction technology of environmental effects at the point of CO2 discharge. In FY 2000, conducted were the ocean survey and the development of assessment technology for CO2 sequestration capacity. In the investigational study, the following three were carried out: 1) survey/observation of the flow field on the line of 165 degrees of east longitude, and acquisition of various data such as the distribution of carbonic acid base substances and the speed of carbon transport; 2) study of the amount of existence of organisms and kind/composition of the medium-depth plankton at the typical observation points; 3) test/experiment actually conducted in the sea area for the experimental equipment for CaCO3 dissolution experimental equipment for studying interactions between the CO2 and CaCO3 dissolved into the medium-depth sea. As to the development of the assessment technology, carried out were the heightening of accuracy of medium-depth ocean circulation models using the inverse method already developed and the estimation of the flow field using the observation data. At the same time, the estimation of the flow field, etc. were conducted using large circulation ocean models. (NEDO)

  3. Report on achievements in fiscal 1998. Research and development of a technology to forecast environmental effect in association with isolation of carbon dioxide in oceans. Ocean surveys and development of a technology to evaluate CO2 separation capability; 1998 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. Kaiyo chosa oyobi CO{sub 2} kakuri noryoku hyoka gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Assuming that CO2 is dissolved and separated in the middle layer in a sea area around Japan, ocean surveys were carried out to acquire fundamental data required for development of a technology to evaluate CO2 separation capability of ocean, and for development of a technology to forecast environmental effect. In addition, using the western part of the Pacific Ocean as the object, development was performed on a numerical model to forecast behavior of CO2 in ocean in the scale of several ten years to several hundred years, and evaluate capability of CO2 separation from atmosphere. The research and development items for the current fiscal year are as follows: (1) ocean surveys, (2) model development, and (3) surveys and studies required for the ocean surveys and experiments. The survey voyage for item (1) was executed centering on the courses of traverse on 140 degree line of east longitude and 147 degree line of east longitude. The voyage surveyed densities of sea water, such data as chemical tracers, discharged mid-layer neutral buoys, carbonic acid based substances, marine living organisms, and sedimentary particles. For item (2), trial calculations were performed by using an inverse model to estimate structures of ocean flows, and discussions were given to enhance the accuracy. For item (3), design and fabrication were carried out on an equipment to experiment on-site dissolution of calcium carbonate, and a chamber for on-site experiments at deep sea bottom. (NEDO)

  4. Element analysis of Japanese traditional papers by PIXE method

    International Nuclear Information System (INIS)

    Suzuki, Tatsuya; Yasuda, Keisuke; Tani, Teruhiro

    2000-01-01

    The Japanese papers, 'washi', are made from the bast fibers of the plants. Since washi have the informations of the raw material plants, there is potentiality of the identification of the production place by the element analysis of the washi. Three kinds of washi made of kozo, which have different habitats, were prepared. The elements in their washi were measured by the PIXE. It was confirmed that the amount of elements included in the washi depend on the habitats of their raw material plants. (author)

  5. Eco Logic signs deal to destroy Japanese PCB stocks

    International Nuclear Information System (INIS)

    Anon.

    1997-01-01

    According to a recent announcement, Eco Logic of Rockwood, Ontario, has entered into a partnership with the Japanese companies Tokyo Boeki and Nippon Sharyo for the destruction of stockpiled PCB materials in Japan, using Eco Logic's non-incineration technology. The deal is reported to be worth about $50 million in revenues to Eco Logic, spread over the next few years. The agreement includes provisions for the Japanese companies to purchase, or manufacture under licence, a number of Eco Logic's gas phase chemical reduction processing units to serve the Japanese market. In exchange for exclusive rights to the Japanese market, Eco Logic will receive license fees and royalties of up to nine per cent for the use of its process. Eco Logic is currently building a demonstration unit under contract with the two Japanese companies. The Japanese PCB waste destruction market is estimated to be worth as much as $400 million. Incineration, the conventional form of disposal, is strongly opposed by local governments

  6. Fiscal 1997 survey report / R and D of important region technology. R and D of technologies giving multi-functional characteristics to C/C composites (development of high-grade surface processing technology for engine members for methane fueled air craft. 1. control technology of micro structures of ultra-high temperature members); 1997 nendo seika hokokusho juyo chiiki gijutsu kenkyu kaihatsu. Fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). 1. chokoon buzai micro kozo seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing members most suitable for aircraft use engines with methane as fuel, the R and D were conducted of technology to reform surfaces and interfaces of materials. In the R and D, the paper took up carbon fiber reinforced carbon composite materials (C/C composites). In the surface control and reformation technology using the ion engineering method, etc., in the sealing processing of C/C composites, tried was the formation of a C/SiC/Si3N4 composite layer which was formed by Si3N4 much smaller in thermal expansion coefficient than SiC. Further, technologies on ion injection, thin film formation, giving of oxidation resistance/corrosion resistance, improving/giving of thermal shock resistance, etc. In the multi-functional coating formation technology such as high liability and corrosion resistance, the study was carried out of the dense composite functionally-gradient layer as thermal stress relaxation layer and the fiber reinforced layer by carbon fiber using pores. Besides, studies were made of technologies of the micro structure control combination, evaluation of ultra-high temperature resistant environmental characteristics, etc. 61 refs., 198 figs., 44 tabs.

  7. FY 2000 report on the results of the project on the R and D of the global environmental industry technology. R and D of the technology for predicting environmental effects associated with the CO2 ocean sequestration (Development of the technology for predicting environmental effects in the area around the CO2 discharge point and survey for supporting study); 2000 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    To obtain the technical outlook for CO2 ocean sequestration by CO2 discharge into the intermediate layer, the R and D was conducted of the technology for predicting environmental effects in the area around the CO2 discharge point, and the FY 2000 results were summed up. In the elucidation study of the behavior at the time of discharging liquid CO2, the melting process of CO2 droplets discharged/dispersed into the seawater of the intermediate layer was observed, and the specific phenomenon of hydrate formation in the process of CO2 droplet formation was grasped. As to the technology for sending CO2 into the ocean and diluting it, experimental study was made of CO2 transportation technology from on the sea to the intermediate layer, technology for rapid dilution immediately after discharge, etc. About the indoor experiment on the CO2 influence on marine organisms, experiment on the CO2 influence was carried out using shells, sea urchin, red sea bream, etc. In the developmental study of models for predicting environmental effects in the area around the CO2 discharge point, the 3D two-phase flow LES model was developed as a model for predicting the CO2 behavior, and the simulation of the liquid CO2 discharge was made at the planned experimental site. The model for evaluation of the biological influence was also made which can consider the interaction between two kinds of organisms. (NEDO)

  8. FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Development of prediction technology of environmental effects around the point of CO2 discharge and the research support survey); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of studying viability of CO2 ocean sequestration by discharging it at the intermediate depth of ocean, the R and D were conducted of 'prediction technology of environmental effects around the point of CO2 discharge,' and the FY 1999 results were summarized. In the study of elucidation of behavior of liquid CO2 at the time of discharge, melting speed of CO2 in water and seawater, 2D CO2 concentration distribution, etc. were measured using the circulation type deep-sea simulation experimental equipment. In the study of technology to send CO2 into the sea and dilute it, the process test using mock liquid was conducted. In the indoor experiment on CO2 effects on marine organisms, conducted were the detailed experiment on long-term effects of low concentration CO2 on sea urchins and shellfish, experiment on CO2 acute effects on eggs/fry and experiment on CO2 effects on adult fish. In the developmental study of the model to predict environmental effects around the point of CO2 discharge, carried out were the improvement of the model for prediction of effects on marine organisms, study of the CO2 diffusion in topographic features supposed to be Hawaii, etc. In the international joint study, measurement/observation technology, facilities, etc. were studied in preparation for the experiment actually conducted in the sea. (NEDO)

  9. FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Development of prediction technology of environmental effects around the point of CO2 discharge and the research support survey); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of studying viability of CO2 ocean sequestration by discharging it at the intermediate depth of ocean, the R and D were conducted of 'prediction technology of environmental effects around the point of CO2 discharge,' and the FY 1999 results were summarized. In the study of elucidation of behavior of liquid CO2 at the time of discharge, melting speed of CO2 in water and seawater, 2D CO2 concentration distribution, etc. were measured using the circulation type deep-sea simulation experimental equipment. In the study of technology to send CO2 into the sea and dilute it, the process test using mock liquid was conducted. In the indoor experiment on CO2 effects on marine organisms, conducted were the detailed experiment on long-term effects of low concentration CO2 on sea urchins and shellfish, experiment on CO2 acute effects on eggs/fry and experiment on CO2 effects on adult fish. In the developmental study of the model to predict environmental effects around the point of CO2 discharge, carried out were the improvement of the model for prediction of effects on marine organisms, study of the CO2 diffusion in topographic features supposed to be Hawaii, etc. In the international joint study, measurement/observation technology, facilities, etc. were studied in preparation for the experiment actually conducted in the sea. (NEDO)

  10. Report on achievements in fiscal 1998. Research and development of a technology to forecast environmental effect in association with isolation of carbon dioxide in oceans. (Surveys on development and research support on a technology to forecast environmental effect in areas in the vicinity of CO2 discharging points); 1998 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. CO{sub 2} horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Atmospheric concentration of CO2 is increasing, and discussions are urged on measures to suppress emission of CO2 into atmosphere. While different CO2 fixing technologies may be conceived, there is a technology to utilize CO2 absorbing capability of ocean by discharging and dissolving CO2 artificially into middle layer of the ocean to separate CO2 from atmosphere. This technology is one of the technologies which are promising in the aspects of technology, economic performance, and possible amount of CO2 reduction. However, it is difficult to say that scientific and technological discussions have been given sufficiently on behavior of CO2 discharged into the ocean, effect of the discharge on environments, and CO2 separation capability of the ocean. Therefore, in the present research and development, a 'technology to forecast environmental effect in areas in the vicinity of CO2 discharging points' is developed to serve for acquiring technological prospect on the feasibility to realize the CO2 ocean separation by discharging CO2 into the middle layer of the ocean. The present fiscal year has performed researches on the following research and development items: elucidation of behavior of liquefied CO2 when discharged into the ocean, CO2 feeding and diluting technologies, indoor experiments on the effects of CO2 on ocean living organisms, and development of a model to forecast environments in areas in the vicinity of CO2 discharging points. (NEDO)

  11. FY 2000 report on the results of the project on the R and D of the global environmental industry technology. R and D of the technology for predicting environmental effects associated with the CO2 ocean sequestration (Development of the technology for predicting environmental effects in the area around the CO2 discharge point and survey for supporting study); 2000 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    To obtain the technical outlook for CO2 ocean sequestration by CO2 discharge into the intermediate layer, the R and D was conducted of the technology for predicting environmental effects in the area around the CO2 discharge point, and the FY 2000 results were summed up. In the elucidation study of the behavior at the time of discharging liquid CO2, the melting process of CO2 droplets discharged/dispersed into the seawater of the intermediate layer was observed, and the specific phenomenon of hydrate formation in the process of CO2 droplet formation was grasped. As to the technology for sending CO2 into the ocean and diluting it, experimental study was made of CO2 transportation technology from on the sea to the intermediate layer, technology for rapid dilution immediately after discharge, etc. About the indoor experiment on the CO2 influence on marine organisms, experiment on the CO2 influence was carried out using shells, sea urchin, red sea bream, etc. In the developmental study of models for predicting environmental effects in the area around the CO2 discharge point, the 3D two-phase flow LES model was developed as a model for predicting the CO2 behavior, and the simulation of the liquid CO2 discharge was made at the planned experimental site. The model for evaluation of the biological influence was also made which can consider the interaction between two kinds of organisms. (NEDO)

  12. FY 2000 report on the survey of geological structures overseas, etc. Volume 2. 'Tanjung Enim IV Coal Exploration Project between Japan and Indonesia'; 2000 nendo kaigai chishitsu kozo chosa hokokusho. 2. Nippon Indonesia sekitan kyodo tansa Tanjung Enim project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The survey was finished in the final fiscal year (FY 2000) of the Tanjung Enim IV Coal Exploration Project between Japan and Indonesia, and a report was summarized on the preliminary coal mining plan. In the design of the optimum mining area and pit, in terms of 3 cases of coal price of $8, $10, and $12/ton, the pit design was made considering rivers, houses, power transmission lines, etc., and the actual coal yield was asked. In the case of coal price of $8/ton, the actual coal yield in pit was 315 million tons in north block and 171 million tons in south block. In the case of coal price of $10/ton, pits are expandable in north block, but not in south block. For all the pit shapes designed, long-term mining plans were worked out. In each of the cases of coal production amount of 1 million, 3 million and 5 million tons, indicated were secular changes in overburden amount and coal quality because of the difference in mining direction. Further studies were made on the deposition plan, simulation of models of mining heavy machines, coal mine facilities, economical efficiency of coal mines, etc. (NEDO)

  13. FY 1999 report on the results of the technology development of super metal. Development of technology of high corrosion resistant iron-base fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing iron/steel materials which enable remarkable improvement of maintenance loads and longevity of oil field developmental materials, study was conducted for remarkable improvement of strength and corrosion resistance by making crystal grain of iron/steel materials micro-fine to the limit, and the FY 1999 results were summed up. The study was conducted on the technology of fine structure formation using strong magnetic field and technology to predict material quality of micro structure using computational science. As a result, it was found that the fine grain even in size can be obtained by a combination of magnetic field orientation and recrystallization. By this, an image was constructed of the industrialization process of fine grained steel production which was combined with warm rolling process and applied strong magnetic field. Using the method to homogenize the finite element method, the basement was established for the method to evaluate an effect of the second phase on mechanical characteristics of fine multi-phase structure steel. The cementite single-phase film which is an important structural phase of carbon steel was successfully formed, and the Young's modulus and Poison ratio were determined as basic data for material design. (NEDO)

  14. Report on achievements in fiscal 1999 on the project for development of an energy use rationalizing technology. Development of a basic technology to design and fabricate an innovative light-weight structure; 1999 nendo kakushinteki keiryo kozo sekkei seizo kiban gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the achievements in fiscal 1999 on development of a basic technology to design and fabricate an innovative light-weight structure. Taking CFRP and aluminum alloy having excellent specific strength as the main object materials, weight reduction and reliability enhancement in aircraft structure are intended, while reducing largely the number of parts. In particular, the wings, the nose and the leading edge construction of civilian aircraft are of the structure assembled with a large number of parts, and are suitable as the research objects. A new conception will be introduced that structural members are fabricated by utilizing the characteristics of integrally formed CFRP, which will be assembled into a whole structure. Large structural metallic members currently used have such drawbacks as the use of great number of parts, complexity in manufacturing processes, low reliability, weight increase and corrosion due to rivet jointing. In order to solve these problems, development will be made on technologies for thin-wall large-size precision casting, and high-accuracy high-quality welding. To combine different kinds of members, and optimize strength, weight and economic performance of the entire structure, high-efficiency integration technologies will be discussed, and prototype full-size structure will be fabricated. The current fiscal year has started up the technology committee and its operation, analyzed technological problems in the entire structure, and established the action programs. An investigation was performed on the technological trends in overseas countries. (NEDO)

  15. Fiscal 1998 achievement report on regional consortium research and development project. Venture business fostering regional consortium in its 2nd year--Creation of key industries (Development of processing of new structure-designed high-performance polymer alloy); 1998 nendo shinkina kozo seigyo koseino kobunshi alloy no seikei kako ni kansuru kenkyu kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are exerted to make novel recyclable polymer alloys excellent in material characteristic and to develop a technology for processing them, for which liquid crystalline polymers equipped with a self-alignment capability are combined with thermoplastic resins. In the research on the alloying of polyethylene terephthalate (PET) and liquid crystal polymers (LCP), studies are conducted about inorganic nucleating additives, thermostabilizers, and mold releasing lubricants, and a success is attained in the manufacture of excellent alloyed pellets. In the injection molding of alloys of PET and LCP, a product is obtained, among those produced with the rate of LCP varied, which behaves excellently even at a high resin temperature of 285 degrees C. It is found about PET/LCP alloys that improvement is achieved with additional LCP in terms of the warpage temperature under load, bending property, strength, and dimensional stability upon exposure to heat. In the study of the response of LCP-diffused PET to a process demanding distortion, an injection-molded product containing 10-20% of LCP is found to exhibit excellent ductility. It is also found that PET/LCP alloys may be cut and machined easily and that therefore their crushing for the recycling purpose will be easy. (NEDO)

  16. FY 1992 report on the survey of geothermal development promotion. Geological structure (geology/alteration zone) survey (No. A-1 - Haneyama area); 1992 nendo chinetsu kaihatsu sokushin chosa chijo chosa hokokusho futai shiryo. Chishitsu kozo (chishitsu henshitsutai) chosa hokokusho (No. A-1 Haneyama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-05-01

    For the purpose of elucidating a possibility of existence of geothermal reservoirs in the Haneyama area, Oita Prefecture, survey of the geological structure (geology/alteration zone) was conducted. The survey was made for the area of 280km{sup 2} lying from Kusu Town to Kokonoe Town, Oita Prefecture in terms of the route survey of 174km, fabrication/judgement of 52 rock slices, whole rock chemical analysis of 21 rocks, age determination, analysis of rock mineral, X-ray diffraction, literature collection, etc. As a result of the survey, the following conclusion was obtained. When considering a possibility of existence of heat source near this area, the area near the present volcanic front was regarded as promising. The fracture structure in the depths seen in the gravity structure (part of sharp dip of gravity) is more closely related to activity of geothermal water than the active structure of E-W system near the earth surface newly formed and is important when considering the existence of geothermal resource. The periphery of the Shishimuta sedimentation zone where Takigami, Oodake, Hacchobaru and Oguni are located was especially regarded as an area propmising of geothermal energy. In the survey area, the geothermal potential was the highest near Noya - Mizuwake Pass. (NEDO)

  17. Sensing of subsurface faults based on an imaging technique for teleseismic waveform data. 2. Feasibility study for application to oblique incidence, multi-event and noise data; Enchi jishin hakei data wo mochiita chika kozo imaging ni yoru chichu danso kenshutsu no kokoromi. 2. Naname nyusha, multi event, noise wo fukumu hakei eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Murakoshi, T; Takenaka, H; Saita, T [Kyushu University, Fukuoka (Japan). Faculty of Science; Suetsugu, D [Building Research Institute, Tokyo (Japan); Furumura, T [Hokkaido University of Education, Sapporo (Japan)

    1996-05-01

    An examination was made on the method in which imaging of subsurface was carried out with teleseismic waveform data for sensing of faults. In the examination, an experiment was done on the sensing of faults with higher precision, by applying oblique incidence as well as perpendicular upward incidence of SH plane waves, and thereby stacking the imaging in plural events. In numerical experiments, 28 observation points were arranged at 500m spaces apart on the surface, and the incident waves were made the SH plane waves having a bell-shaped time function, with incidence made at an angle varied as 0{degree}, +15{degree} and -15{degree} from the lowest layer of a model. In the calculation of the wave motion field, a difference calculus with secondary accuracy was used for both time and space. In addition, data was prepared with a random noise added to a synthesized waveform to be used as observation data. The calculated waveform data were likened to the observation waveform, to which the method for imaging faults was applied. Consequently, it was noted that satisfactory results were obtained compared with the case where faults were sensed by one event alone. 5 refs., 4 figs.

  18. Project for surveying improvement in energy demand and supply structure (comprehensive survey on improvement in energy demand and supply). FY1998 report on achievements of Technical survey on pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo (energy jukyu kodoka sogo chosa). Shoden hatsuden system no gijutsu chosa 1998 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper reports the achievements on research of pyroelectric power generation systems in fiscal 1998. In the research, a small continuous pyroelectric conversion equipment was fabricated and experimented. The experiment using an aluminum foil electrode revealed that the foil melts during discharge opening holes, thus making it impossible to increase net conversion efficiency. The net conversion efficiency was derived in an experiment using foil evaporated with indium instead of the aluminum foil. Indium has inferior electric conductivity to aluminum, but is melting point is as low as 145.6 degrees C. Therefore, if a pyroelectric film had electric fatigue due to use over an extended period of time, indium may be melted to make recovering and reusing pyroelectric copolymer possible. Thus, the indium electrode was found suitable for pyroelectric conversion. Analysis of the experimental data indicated that the final possible net output can be 7.6 W/m{sup 2} if each operation variable considered possible in the future is superimposed on the pyroelectric film. This survey revealed that low-temperature waste heat can be converted to high voltage continually by using the pyroelectric conversion equipment at CANMET Energy Technology Centre. (NEDO)

  19. Fiscal 1999 achievement report on research and development of industrial technology of new industry creation type. Research and development of intelligent material and structural system (Development of energy use rationalization technology); 1999 nendo chiteki zairyo kozo system no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Fiber or foil shaped sensor materials and actuator devices were integrated with composite materials and composite material structures for processing and controlling information, and then studies were conducted about materials and structural systems for enabling real-time detection of damage in materials and structures, examination of soundness, control of noise and vibration, and the like. Concerning optical fiber sensors in the development of smart manufacturing technologies, the impact imposed on composite materials by sensors embedded therein was investigated, and the scope of their applicability was determined. In the development of actuator materials and devices, ceramic actuators were fabricated by microwave sintering, and it was found that they were higher in performance by 30% than actuators of the conventional design. In the testing of demonstrators, molded body monitor basic tests using optical fiber sensors were conducted for jet engine static vane models, and temperature dependence of optical intensity was understood. (NEDO)

  20. Basic studies on design supporting system of offshore structure. Part 2. Implementation of structural design supporting system of offshore structures; Kaiyo kozobutsu wo taisho to shita sekkei shien system ni kansuru kisoteki kenkyu. 2. Kaiyo kozobutsu no kozo sekkei shien system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Nomoto, T.; Hamada, K.; Aoyama, K. [The University of Tokyo, Tokyo (Japan)

    1996-12-31

    In order to improve the existing design-supporting system for offshore structures, new functions are added to evaluate information of the products, especially those for structural designs. The structural analysis system should be provided with a function of design modification, to efficiently support the structural analysis of these structures. The new system adds hierarchy of various offshore structure models and three-dimensional dimensions to clarify structural and geometrical constraints and design-modification function. The design-modification function is included by use of the hierarchy. The other new functions are finite element analysis systems for the main structure and components, and rigidity calculation for the main structure. The main structure and functional element models are confirmed to be useful also for utilization of information, and provide necessary information of the product models. 11 refs., 11 figs.

  1. FY 1999 research and development of technologies for creating original high-function materials. Development of technologies for functionalized materials for power generating facilities (Report on the R and D results of controlling precise structures of polycondesed systems); 1999 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu (shukugokei seimitsu kozo seigyo no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development project is implemented for the polymerization catalysts and precise polymerization processes which can freely control the primary structures, e.g., molecular weight, regularity, branching and terminal group structures, of the polymers produced by polycondensation and ring-opening polymerization, in order to drastically improve their functions, and the FY 1999 results are reported. The basic studies on the precise polycondensation successfully lead to chemoselective synthesis of polymers by the direct polymerization, and synthesis of polyamides of narrow molecular weight distribution and high-molecular-weight aliphatic polyesters. The other items studied include precisely, regularly sequential polymerization by amine activation, innovative synthesis of polycarbonate, precise control of branching structures, regioselective oxidative coupling polymerization, and matrix polycondensation. The basic studies on the controlled ring-opening polymerization cover cationic ring-opening polymerization behavior of 6-membered thiocarbonate derivative having an ester group, to generalize the polymerization controlled by neighboring group participation. The other items studied include precise control of branching structures, molecular weights, network polymer structures, and polymer unit sequences. (NEDO)

  2. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  3. Report on results concerning development of supermetal technology, R and D of offshore oil production supporting system, and development of technology for aluminum-based high-anticorrosive microstructured metallic material (FY2000); Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kaitei sekiyu seisan shien system kenkyu kaihatsu (Aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of developing high strength and high-anticorrosive aluminum-based material through microstructure control, R and D was conducted, with fiscal 2000 results compiled. In the research of grain refinement mechanism, molten metal rolled stock was experimentally produced in which Mg content was varied 0-2.5 mass % with Al-2.5 mass % Mn as its base. As a result, a microstructure with an average grain size of about 3 {mu}m was obtained by processing the alloy through homogenization at 550 degrees C, cold rolling by 91% and the final treatment at 350 degrees C without Mg addition. Addition of Mg increased square grain boundaries in the microstructure, raising proof stress to about 180 MPa in Al-2.5%Mn-2.5%Mg alloy. In the research of development of the machining process, a rapid heating process was performed on a typical aluminum alloy, with the effect examined, by an alloy system or a plate thickness, on the electric power used and on the temperature reached. A rapidly heated aluminum alloy plate turned to have a microstructure with equi-axed grains of a uniform size, compared with a salt bath processed material heated at the same temperature. (NEDO)

  4. FY 1999 report on the results of the technology development of super metal (R and D of the undersea oil production support system). Development of technology of aluminum-base high corrosion resistant fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu (aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihtsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing aluminum materials excellent in industrial characteristics, a study was conducted to create large-sized aluminum materials having mesoscopic crystal structure, and the FY 1999 results were summarized. In this fiscal year, to create the fine crystal grain structure, the following were conducted: fundamental study of high strain accumulation process, study of a mechanism of fine crystal grain formation, development of the processing method, and development of evaluation technology. In the study of high strain accumulation process, effects were examined of conditions of molten metal rolling on castability. Fundamental studies were also made of innovative technologies such as ECAP method, pre-forged structure controlling rolling, accumulative roll bonding and thermomechanical treatment. In the study of the mechanism of fine crystal grain structure formation, the following were conducted: Al-Mn base alloys produced by molten metal rolling, 6061 alloys by warm rolling with different peripheral speed rolling, and 7000 group alloys by warm rolling. As to the processing method, study was made on low-temperature rolling technology and rapid heat treatment technology. As to the evaluation technology, study was made on evaluation of crystal grain diameter by EBSP. (NEDO)

  5. Fiscal 1998 research report. Industrial science and technology research project / R and D on creative advanced functional materials (structure-controlled materials) / Harmonized molecular materials; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) seika hokokusho. Bunshi kyocho zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    R and D on harmonized molecular materials aim at establishment of the technology fabricating self-assembled organic molecular films on solid surfaces which have potentials of mechanical response to electric fields, electroluminescence or optical functions. Molecule harmonization expresses new structures and functions difficult to be expressed by each molecule alone, by cooperative interaction between molecules due to noncovalent bond. Functional thin films were developed by controlling alignment and/or arrangement of molecules with an aid of self-assembling processes. Thiol compounds with larger dielectric anisotropy were synthesized as electric field responsive self-assembled films. {pi}-conjugated compounds composed of phenyl-capped oligothiophenes were synthesized as electroluminescent self-assembled films, and their high crystallinity and efficient electroluminescence were found. Heat- and solvent-resistant lyotropic liquid crystalline (LLC) aligning polymers such as polyamine and polyimine were synthesized as new optically functional LLC dye self-assembled films. (NEDO)

  6. Developments of DPF systems with mesh laminated structures. Performances of DPF systems which consist of the metal-mesh laminated filter combustion with the alumina-fiber mesh, and the combustion device of trapped diesel particles; Mesh taso kozo no DPF no kaihatsu. Kinzokusen to arumina sen`i mesh ni yoru fukugo filter to filter heiyo heater ni yoru DPF no seino

    Energy Technology Data Exchange (ETDEWEB)

    Kojima, T; Tange, A; Matsuda, K [NHK Spring Co. Ltd., Yokohama (Japan)

    1997-10-01

    For the purpose of continuous run without any maintenance, new DPF (diesel particulate filter)systems laminated by both metal-wire mesh and alumina-fiber mesh alternately, are under the developments. The perfect combustion of trapped diesel particulate can be achieved by a couple of the resistance heating devices inserted into the filter. 5 refs., 7 figs., 3 tabs.

  7. FY 2000 report on the survey of geological structures overseas, etc. Volume 1. 'Tanjung Enim IV Coal Exploration Project between Japan and Indonesia'; 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. 1. Nippon Indonesia sekitan kyodo tansa Tanjung Enim project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper summarized the results of the surveys in the final fiscal year (FY 2000) and in the past five years of the Tanjung Enim IV Coal Exploration Project between Japan and Indonesia. In FY 2000, conducted in the South Arahan area were the surface reconnaissance (50km+ACI-2), boring survey (11 holes, 1,847m), borehole physical logging (11 holes), reflection method seismic survey (3 traverse lines), pumping test, coal analysis (112 specimens), etc. As a result of the exploration/study made during 5 years, coal reserves in the South Arahan area were 223 million tons in north block (proved coal reserves: 213 million tons) and 332 million tons (proved coal reserves: 303 million tons) in south block. The coal in the area is in the depth of {+-}0m from surface, and the coal reserve is enough for large scale open pit mining. Further, coal reserves in the Banjarsari area were 442 million tons (proved coal reserves: 330 million tons) in the whole area and 223 million tons (proved coal reserves: 214 million tons) in the syncline part. About the syncline part promising as that for open pit mining, the overburden ratio was divided into three for calculation: 2:1, 3:1 and 4:1 or below. (NEDO)

  8. Fiscal 1998 R and D on original advanced material creation technology (development of precise structure control materials for oil refinery improvement). R and D result report on multi-dimensional polymers; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho. Tajigen kukan polymer no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For development of radical-controlled synthesis technology of aromatic compounds using enzyme-related catalysts and synthesis technology of ordered compounds, and development of synthesis technology of new polymer groups with non-covalent bond linkages and new topological structures, this R and D on multi-dimensional polymers is promoting 2 research themes, (1) precise polymer synthesis technology using enzyme-related catalysts, and (2) chemical synthesis technology for polymers with non-covalent bond linkages and new topological structures. The joint research on (1) precise polymer synthesis technology using enzyme-related catalysts established the high-yield synthesis technology of phenol dimer first in the world. The joint research first studied the synthesis using 2,6-dimethylphenol as monomer through synthesis of phenol groups using ferrosalen, and obtained the mixture of polymer components more than 10,000 in molecular weight and low-molecular weight components by using 1,4- dioxane as solvent. (NEDO)

  9. Structure and coke preventing characteristics of Ca-Ni-Mo/Al sub 2 O sub 3 catalyst for hydrogenation of brown coal liquid bottoms. Kattan ekikaabura suisokayo Ca-Ni-Mo/Al sub 2 O sub 3 shokubai no kozo to tansoshitsu seisei yokusei sayo

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, T. (Cosmo Oil Co. Ltd., Tokyo (Japan)); Kaneko, T.; Kageyama, Y. (Mitsubishi Kasei Corp., Tokyo (Japan). Research Center); Kawai, S. (Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan))

    1990-09-01

    Operating a 50 t/d fixed bed pilot plant, hydroprocessing of de-ashed coal liquid bottoms (DAO) derived from Victorial Brown coal liquefaction has been carried out in Australia using a newly developed Ca-Ni-Mo/Al {sub 2} O {sub 3} catalyst. This catalyst has a great advantage compared with conventional molybdenum catalysts in that there is less coke formation using this catalyst as indicated by 5,000 h runs in a 0.1 t/d bench scale plant. In this paper, the catalyst active center and the role of Ca in the Ca-Ni-Mo/Al {sub 2} O {sub 3} catalyst were analyzed using Raman, TPS-XPS, EXAFS and AES methods. Molybdenum is loaded as CaMoO {sub 4} and X-ray diffraction data. But the oxide is changed to MoS {sub 2} after sulfiding treatment. Data of the Mo-S bond obtained from EXAFS analysis indicated that MoS {sub 2} has a tendency to pile up on the Ca-Ni-Mo/Al {sub 2} O {sub 3} catalyst. 20 refs., 12 figs., 5 tabs.

  10. Report on results concerning development of supermetal technology (FY2000). Development of technology for high-anticorrosive iron-based microstructured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of greatly improving strength and corrosion-resistance through ultra-refinement of crystal grains of steel materials, research was conducted on microstructure refinement technology utilizing strong magnetic fields and on mechanical property estimation technology for ultra-refined structure steel using computational science, with fiscal 2000 results compiled. In the research for grain refinement utilizing magnetic fields, an inline experiment of transformation was carried out and, as a result, equi-axed grains of 1.6 {mu}m were attained on a 3 mm thick steel plate of commercially used composition by a method of recrystallization after cold rolling. The experiment revealed that the 1 {mu}m grains could be obtained by setting cold-rolling work load to 80%. In addition, data were acquired relating to conditions such as steel composition affecting the formation of orientation in structures, work load and rolling temperature for areas to be recrystallized, holding temperature and time in the magnetic field, and intensity of the magnetic field. In the research for estimating mechanical properties of microstructures by computational science, a Monte Carlo simulation was carried out by employing the result of a polycrystal plasticity method program as the initial value, with a prototype established of the integrated simulation method from the deformation to the microstructure formation. (NEDO)

  11. Report on the FY 1993 basic survey for industrialization related to the survey of overseas geological structure (Muara Lakitan area, Indonesia). Tables and drawings; 1993 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa hokokusho (Indonesia Muara Lankin chiku). Hyo oyobi zumen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    These are tables and drawings for the FY 1993 basic survey for the coal mine development/industrialization in the Muara Lakitan area of Indonesia. The geological structure in the survey area is under six sets of the anticline/syncline structure which have an NW-SE axis of fold, and exposes the Muaraenim seam repeatedly. The theoretical coal reserve in the depth down to 200m of each of the seams, Nos. 1, 2, 5, 12 and 13, which are great in coal seam change and exist relatively stably, is 143 million tons. The depth for adoption of the shovel/truck system open pit mining seems to be 50m or shallower, and the production is to be approximately 70 million tons. The coal is classified into a subbituminous coal-brown coal rank of the JIS classification. As tables, included were a table of the calculation of coal amount by seam and a table of the analytical result of coal by seam. As drawings, included were borehole logs of coal seam by boring, diagrams of thickness by seam such as the seam thickness/diagrams of thickness by seam such as the coal thickness, diagrams of range of calculating the coal amount, etc. Besides, in relation to coal properties, the report included value diagrams by seam of the inherent moisture, the ash, the volatile matter, the fixed carbon, the heating value, and the total sulfur content. (NEDO)

  12. Basic studies on design supporting system of offshore structure. Part 2. Implementation of structural design supporting system of offshore structures; Kaiyo kozobutsu wo taisho to shita sekkei shien system ni kansuru kisoteki kenkyu. 2. Kaiyo kozobutsu no kozo sekkei shien system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Nomoto, T; Hamada, K; Aoyama, K [The University of Tokyo, Tokyo (Japan)

    1997-12-31

    In order to improve the existing design-supporting system for offshore structures, new functions are added to evaluate information of the products, especially those for structural designs. The structural analysis system should be provided with a function of design modification, to efficiently support the structural analysis of these structures. The new system adds hierarchy of various offshore structure models and three-dimensional dimensions to clarify structural and geometrical constraints and design-modification function. The design-modification function is included by use of the hierarchy. The other new functions are finite element analysis systems for the main structure and components, and rigidity calculation for the main structure. The main structure and functional element models are confirmed to be useful also for utilization of information, and provide necessary information of the product models. 11 refs., 11 figs.

  13. FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (Development of technologies for rational use of energy); 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the R and D project for development of intellectual materials and structural systems, as part of development of technologies for rational use of energy. The program for development of health monitoring technologies produces the bright prospects for commercialization of the fine FBG (Fiber Bragg Grating) sensor which can be embedded in a CFRP prepreg, and establishes the crack detecting method. The program for development of smart manufacturing technologies describes the dielectric constant sensor capable of monitoring the curing process, detection of the cured conditions by the optical fiber sensor, and development of the performs by RTM (Resin Transfer Molding). The program for technological development of the active-adaptive structures conducts the vibration- and noise-controlling tests for the small-size structural elements, confirming that the damping coefficient is improved by at least 20% and acoustic power is reduced by at least 30%. The program for developing the actuator materials and elements improves the piezoelectric characteristics of the PZT-based materials by hybrid sintering, and develops the actuators of high-durability FGM (Function-Gradient Materials). It also develops the foil- and belt-shaped shape memory alloys by arc-aided dissolution and rapid solidification of Ti-Ni-Cu-based alloys. (NEDO)

  14. Fiscal 1998 research report on the R and D on industrial science and technology for creating new industries. R and D on intelligent material and structure systems (Development of practical technology for rational use of energy); 1998 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a part of development of intelligent material/structure systems, study was made on practical technology for rational use of energy. For resource saving and energy saving (smartening) for large and complex machines and structure systems, light-weight long-life materials/structures are indispensable. Study was thus made on the basic technology of material/structure systems equipped with realtime defect detection function, structural integrity diagnosis function and control function of noise and vibration through information processing and control by integrating composite material/structure and fiber or film sensor material/device. For development of smartening technology, sensing technology was studied to detect the interior structure of composite material/structure compacts. The basic fabrication technology of ceramic actuator materials/devices, and shape memory alloy system actuators were put into development. Smooth connection and cooperation among groups were promoted through the technical committee and research on domestic and overseas trends for forming common knowledge. (NEDO)

  15. Correlation between interstitial flow and pore structure in packed bed. 1st Report. Axial velocity measurement using MRI and visualization of axial channel flow; Juten sonai ryudo to kugeki kozo no sokan. 1. MRI ni yoru jikuhoko ryusoku bunpu no keisoku to jikiuhoko channel ryu no kashika

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, K; Yokouchi, Y; Hirai, S [Tokyo Institute of Technology, Tokyo (Japan)

    2000-02-25

    Structure and velocity measurements using magnetic resonance imaging (MRI) have been performed experimentally to obtain a correlation between pore structure and interstitial flow through the packed bed of 5 mm diameter in the tube of 36 mm ID. To measure axial velocity maps of water flow through the packed bed, the phase method of using the phase difference of water spin magnetization between flowing and stagnant fluids by applying magnetic fields with bipolar gradients was employed. The spatial resolution of the obtained map in 0.2 mm x 0.2 mm x 0.5 mm. It was made clear from the obtained axial velocity maps that channel flows with higher axial velocity were induced not only near the wall but also in the internal region of the packed bed. Furthermore, pore structure of the packed bed was characterized from multi-slice images by partitioning of void space and combining of each pore section along the axial direction to analyze the structure-flow correlation. It was found from image analysis that axial channels with long and straight void space existed in the pore structure, and that most of the channel flows with higher axial velocity were induced in the axial channels. The flow rate through an axial channel depends on the square of the averaged cross section of the axial channel. (author)

  16. Report on the FY 1995 basic survey for industrialization related to the survey of overseas geological structure (Pondok Labu East area, Indonesia). Data attached 3 (BIP survey report); 1995 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Indonesia Pondok Labu higashi chiku) hokokusho. Tenpu shiryo 3 (BIP chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The survey was conducted based on 'Scope of work for detailed coal exploration in the Pondok Labu East area of East Kalimantan Province, Kalimantan, Indonesia' concluded on June 16, 1995 between NEDO and P.T. Tanito Harum which owns the mining right. This is a BIP survey report. The strike/dip read from the isobath diagram drawn from the result of the boring little agreed with the stratification in the BIP survey. The BIP stratification is greater in strike and dip than in depth. The latter possibly includes false beds and surfaces cut-off/separated by channel, but roughly speaking the structure becomes such a structure as in the isobath diagram. It suggests that there is local undulation everywhere. Judging from the appearance frequency of open type cracks and the size of hole, there are no problems of the crack type decline at frequency of less than one per 5m at the time of drilling mine roadway. The state of upper/lower basement was not good. Refer to the paper (JN9940854). (NEDO)

  17. Research report on promotion of geothermal energy exploitation for fiscal 1997. Test drilling into the structure, construction work for research, and analysis (No.B-4 Kuenohira district); 1997 nendo chinetsu kaihatsu sokushin chosa. Kozo shisui chosa koji oyobi kaiseki hokokusho (No.B-4 Kuenohirayama chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    Cuttings from a test drilling in the Kuenohira district, Oita Prefecture, are subjected to analysis. The result of ground surface investigation suggested the presence of a magma reservoir to serve as heat source and a highly permeable zone along a fault to help the formation of a thermal water retention system. At the N9-KH-1 drilling site, however, no geothermal reservoir is found along the periphery of the subsidence in the western part of the research area. In this district, it is deemed, no geothermal reservoir has been formed due to shortage of heat supply from the heat source and insufficient geothermal water activity. It is also deemed that the district, in which fractures of the E-W system, NNW-SSE system, and NE-SW system are distributed, is a region at which meteoric water flows into larger convection systems. As for the westward stretch of the geothermal reservoir (where the N9-KH-1 site is situated) that has developed on the swell of the basement, detected to exist at N2-MW-2 and N3-MW-6 in the eastern part of the research area, it is found to be not so extensive. (NEDO)

  18. Application of forking genetic algorithm to the estimation of an S-wave-velocity structure from Rayleigh-wave dispersion data. With special reference to an exploration method using microtremors; Rayleigh ha no bunsan data kara S ha sokudo kozo wo suiteisuru inversion mondai eno kotaigun tansaku bunkigata identeki algorithm no tekiyo. Bido tansaho ni kanrenshite

    Energy Technology Data Exchange (ETDEWEB)

    Cho, I; Nakanishi, I [Kyoto University, Kyoto (Japan); Ling, S [Nihon Nessui Corp., Tokyo (Japan); Okada, H [Hokkaido University, Sapporo (Japan)

    1997-10-22

    Discussions were given on a genetic algorithm as a means to solve simultaneously the problems related to stability of solution and dependence on an initial model in estimating subsurface structures using the microtremor exploration method. In the study, a forking genetic algorithm (fGA) to explore solid substance groups was applied to the optimizing simulations for a velocity structure model to discuss whether the algorithm can be used practically. The simulation No. 1 was performed by making the number of layers four for both of the given velocity structure and the optimizing model. On the other hand, the simulation No. 2 was executed by making the number of layers for the given velocity structure greater than that for the optimizing model. As a result, it was verified that wide range exploration may be possible for the velocity structure model, and that a large number of candidates for the velocity structure model may be proposed. In either case, the exploration capability of the fGA exceeded that of the standard simple genetic algorithm. 8 refs., 4 figs., 2 tabs.

  19. Study of reciprocating engine with Z mechanism. Part 1. Discussion of effect on the performances of new concept engine; Yodo shiten riron wo mochiita ofuku do engine ni kansuru kenkyu. 1. Shinkihon kozo no donyu ni yoru seino kojo no suisatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshizawa, Y; Fukuzaki, S; Kanno, M [Yoshiki Industrial Co. Ltd., Yamagata (Japan)

    1997-10-01

    A new reciprocating engine was developed as an application of new mechanism named as `Z mechanism.` In this new engine, the piston motion is described by a simple sine function and gives lower velocity around top dead center than that in conventional piston engines. Thus, the mode of combustion in this engine is closer to constant-volume process and gives higher thermal efficiency than ordinary engines. Use of Z-mechanism also eliminated high-order components of vibration that ordinary engines suffer. Development high-performance engine was successfully conducted with this new mechanism. 4 refs., 11 figs., 1 tab.

  20. Research and development of a technology to create original high-function materials in fiscal 1998 (development of precision structure controlling materials by improving petroleum refining). Report on achievements in research and development of precision catalytic polymerization; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu (seimitsu shokubai jugo no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research and development on precision catalytic polymerization aims at developing polymerizing catalysts that can control arbitrarily the molecular weight and three-dimensional regularity by which rapid enhancement can be expected in performance of additional polymerization type polymers, and the primary structure of terminal groups. Works are being done on two sub-themes of ultimate additional polymerization and orientation catalyst polymerization. The research and development of the ultimate additional polymerization included structural control in polymerization reaction in vinyl chloride, vinylester and acrylic monomers, radical polymerization with precision orientation control, anionic polymerization with precision structural control, and precision polymerization utilizing asymmetric metal porphyrin complexes. In the research and development of the orientation catalyst polymerization, the orientation catalyst polymerization was researched and developed, elementary reaction of metallocene was elucidated, high-performance carrier catalysts were developed, advanced function polymers were synthesized at high precision based on metathesis, and improvement of functions of polyolefin was researched and developed. Surveys and studies were carried out on fundamental technologies common to the above two themes re-commissioned to five universities. (NEDO)

  1. Fiscal 1999 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of hypersensitive photocatalyst using oxide semiconductor thin film having nanostructure; 1999 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Nano bisai kozo wo yusuru sankabutsu handotai usumaku ni yoru chokokando hikari shokubai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The thin film structure of photocatalytic titanium oxide, capable of efficiently decomposing hazardous pollutants or the like, is refined to have a nanometric scale structure for a larger specific surface for the development of a photocatalytic thin film or powder film and for the development of decomposition capable air cleaner using a thus developed photocatalytic film. Described in this report are the results of a study conducted to elucidate the fabrication conditions, nanostructures, and photocatalytic features of titanium oxide thin films formed by spray thermolysis, RF (radio frequency) sputtering, reactive sputtering, and sol-gel process, a study of hazardous pollutant decomposing capability and nanostructure, the establishment of fabrication technologies, and the construction of a prototype air cleaner with the results of the said studies applied thereto. Among the various fabrication methods, the technology involving a hypersensitive thin film photocatalyst was established by combining the reactive sputtering method and the sol-gel method. It was found that the formation of prismatic crystals in the sol-gel method was the most important in achieving high performance in the hypersensitive thin film photocatalyst. (NEDO)

  2. Fiscal 1999 achievement report. Important regional technology research and development--Research and development of eco-tailored tribo-material creation process technology (High-order composite structure material creation process technology); 1999 nendo eco tailored tribo material sosei process gijutsu seika hokokusho. Koji fukugo kozo material sosei process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development is carried out for the creation of tribo-materials light in weight and free of harmful substances for the manufacture of brakes and rolling bearings for transportation equipment. In the study of the manufacture of tribo-materials by the powder sintering process, various intermetallic compound powers of Fe, Ti, and Al are prepared and sintered by the mechanical alloying method and the gas atomization method, and the compounds are examined for mechanical and tribological properties. In the study of the melting method, different specimens of the same alloy are melted and cast using high frequency, plasma arc, etc., and their mechanical properties and tribological properties are measured. In the study of the manufacture of brake disk materials and the manufacturing process, a small high-temperature abrasion tester is experimentally built and installed, and friction test materials free of Cu and Sb, suitable for the construction of light-weight rotors, are manufactured and tested for abrasion. In the study of the manufacture of materials for roller bearings and the manufacturing process, candidate materials are selected, pulverized by gas atomization, mechanical alloying, etc., and then sintered, and are tested for their bonding capability. (NEDO)

  3. Applicability of the spatial autocorrection method for estimation of basement structure in Kanto plain. Array measurements of microtremors close to the Iwatsuki and Shimosa deep borehole observatory; Kanto heiya no kiban kozo suitei no tame no kukan jiko sokanho no tekiyosei. Iwatsuki Shimosa jiban katsudo kansokusei ni okeru array bido kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Umezawa, N; Shiraishi, H [Saitama Institute of Environmental Pollution, Saitama (Japan)

    1996-10-01

    To investigate applicability of the spatial autocorrection method which is a microtremors exploration method for the estimation of basement structure, array measurements of microtremors were performed using the Iwatsuki and Shimosa deep borehole observatory where detailed structures were clarified as well as the Fuchu and Koto deep borehole observatory. In this study, estimated velocity structures of S-wave were compared with the geological sequence and results of acoustic velocity logging. The phase velocity was estimated by the spatial autocorrection method using FFT. The phase velocity with a smooth normal dispersion was observed in the periodic range from 0.5 to 5 sec in Iwatsuki, and from 0.5 to 4 sec in Shimosa by the combination of four-point circular arrays with radii of 100, 300, and 600 m. The underground structures estimated from the phase velocities coincided well with the geological sequence, and results of acoustic velocity logging and velocity logging for each borehole. For the Iwatsuki borehole, the basement velocity was also estimated properly in the periodic range of observation. While, for the Shimosa borehole, measurements with the period around 6 sec were required to estimate the basement velocity more accurately. 13 refs., 11 figs., 1 tab.

  4. FY1998 results report on the priority area research and development of 'innovative processing technologies for producing ecologically tailored tribo-materials'. Innovation processing technologies for producing high-order composite structured material; 1998 nendo eco tailored tribo material sosei process gijutsu seika hokokusho. Koji fukugo kozo material sosei process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With research and development conducted for the purpose of improving performance of tribology-related parts in outdoor industrial equipment and transportation machinery, the results for fiscal 1998 were summarized. In the trial manufacturing of tribo-materials by a powder metallurgical method, since Fe-Ti-Al based intermetallic compound was promising, four kinds of powder samples were manufactured by mechanical alloying. Tribo-materials by a melting and casting method were also manufactured using the same samples and found to be inferior to the powder sintered materials in dynamic properties. In the evaluation of trial manufacturing of materials for brake disks, the result of measurement on abrasion loss and a friction coefficient by a high temperature abrasion tester revealed that Ti-Al based alloys were promising as composition metal. In the examination of the trial manufacturing of materials for bearings, in dealing with high loading of bearings, investigations were conducted on the physical properties of a low carbon steel backing with heating and rolling applied as well as on overlay materials. For materials for bearing alloys, Cu based powders were examined which were manufactured by a gas atomizing method. (NEDO)

  5. Fiscal 2000 report on result of R and D of industrial science and technology that creates new industry. Development of supermetal technology (development of nano-amorphous structured material); 2000 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    R and D was conducted for the purpose of manufacturing innovative iron-based alloy materials that excel in high temperature strength, toughness and superplastic forming, with fiscal 2000 results compiled. In the technological study on high-speed grain accumulation and superplastic forming, the researchers were engrossed in developing an aluminum bulk material of nano-crystals. This year, an Al-Fe two-element based alloy using Fe element was evaluated in the composition, thermal processing conditions and physical properties, with a bulk material obtained having a grain size of several tens in nm at 2at% Fe level, a strength of 750-850 MPa and a tenacity (Kc value) of 45-65 MPa(center dot)m{sup 1/2}. In the research of technologies for utilizing and controlling high density energy, design of materials was progressed for strong-acid resistant dew point corrosion materials, leading to the discovery of an alloy composition Ni-10Cr-5Nb-16P-4B whose subcooled liquid zone was wider than the Ta-added alloy of the previous year. Use of He gas as injection gas enabled a quality amorphous powder to be obtained in kg units. In the development of bulk amorphous producing technologies, this powder was thermostatically rolled to make a dense bulk amorphous plate of 2.8 mm thick and about 100 mm long. (NEDO)

  6. Fiscal 1998 research report on the R and D on industrial science and technology for creating new industries. R and D on intelligent material and structure systems; 1998 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at development of the basic technology of the structure system which has the same intelligent functions as living body such as perception, decision and response through information processing/control (brain) by integrating advanced complex material structure (skeleton), fiber or film sensor material/device (nerve) and actuator material/device (muscle). This report describes the fiscal 1998 research result. On health monitoring technology, study was made on development of high-performance sensors, and a damage detection and self-diagnosis system for structural integrity. On active adaptive structure technology, study was made on improvement of a quasi-elastic behavior model for shape memory alloys, and a candidate actuator for noise and vibration reduction. On actuator materials and devices, study was made on the relation between electronic properties and dielectric/electro-strictive characteristics of the latest advanced ceramic materials available. Creation of silent smart structure was also clarified. Smooth connection and cooperation among groups were promoted through the technical committee and research on domestic and overseas trends. (NEDO)

  7. Research report for fiscal 1998. Research of feasibility of energy supply/demand structure overseas improvement (research of feasibility of more effective energy use for Russian energy consuming industries); 1998 nendo kaigai energy jukyu kozo kodoka jisshi kanosei chosa. Roshia no energy tashohi sangyo ni okeru energy yuko riyo nado jigyo jisshi kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A report is made outlining the economic situation and industrial policies in Russia and the actual state of energy consuming industries (thermoelectric power generation, oil refining, and iron making) in that country. In Russia, energy efficiency is much lower than in advanced countries in the West, and the improvement of energy efficiency is a serious task to solve in the Russian fuel energy department. Cited to explain the poor efficiency are facilities growing antiquated, delay in the introduction of new technologies and instruments, insufficient maintenance, and the weak consciousness of energy saving. Although the electric power circle and energy related departments are conscious of the need of endeavors for improving energy efficiency, yet it is too difficult for corporations themselves to invest heavily in facilities. When Japan implements a model project for saving energy in Russia, it will be greatly contributing to the improvement of energy supply/demand in Russia, to the stabilization of social and economic states in that country, and to the prevention of global warming. (NEDO)

  8. FY 2000 report on the results of the research and development project for utilization of information of high-molecular-weight structures in a living body. Survey on the technological trends of utilizing the reactions with metals in a living body; 2000 nendo seitai kobunshi kozo joho riyo gijutsu kaihatsu chosa hokokusho. 'Seitai kinzoku hanno riyo gijutsu' ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the survey on the technological trends of utilizing the reactions with metals in a living body, noting the bio-processes effectively coping with the environmental problems. The effects of heavy metals on microorganisms have been investigated on the molecular biology level, but are not fully elucidated. Recently, the microorganisms capable of converting inorganic metal ions in water into the insoluble compounds have been known, leading to possibility of bioremediation to solve pollution by heavy metals, which have detrimental effects on human health. Heavy metals must be recovered, because they are not extinct by decomposition. The plant aided purification has been attracting attention to cope with heavy metals accumulated in soil. Application of bacteria-aided leaching, which is adopted as one ore smelting process, to the technologies for utilizing metals in a living body has been expected, because diversified activities of inanimate matters in extreme environments have been known. Recently, bio-machining of metals aided by Thiobacillus ferrooxidans, one species of independent nutrient bacteria capable of eating metals, has been developed to a potentially viable stage. (NEDO)

  9. Research and development of system to utilize photovoltaic energy. Survey on the high-durability and low-cost materials for constructing the solar-cell module and its structure; Taiyoko hatsuden riyo system no kenkyu. Taiyo denchi module yo kotaikyusei tei cost zairyo, kozo ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the results obtained during fiscal 1994 on a survey on the high-durability and low-cost materials for constructing the solar-cell module and on its structure. With respect to forms and materials used in the present solar-cell modules, identification was made on the current status of products commercially available and developed inside and outside Japan. Main types of solar cells used for electric power are of crystal-based silicon. Amorphous silicon and CdS-CdTe are used for consumer applications of indoor and outdoor use. As regards transparent resin materials, fluorine resin, PET, acryl, and polyimide are used as surface materials, and EVA, silicon and PVB are often used as fillers. Developments inside and outside Japan are limited to systems of polycarbonate, methacryl, fluorine, polyurethane, acryl and polyester. Butyl rubber and polyurethane are used as sealing materials. Developments are being performed on silicon rubber, polychloroprene rubber and EPT rubber for shaped materials, and silicon systems, urethane systems and polysulfide systems for non-shaped materials. 3 figs., 8 tabs.

  10. Study on unified fatigue strength assessment method for welded structure. Hot spot stress evaluating method for various combinations of plate thickness and weld leg length; Yosetsu kozo no toitsutekina hiro kyodo hyokaho ni kansuru kenkyu. Itaatsu to yosetsu ashinaga no kumiawase ni taisuru hot spot oryoku sanshutsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Nihei, K.; Inamura, F.; Koe, S. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-12-31

    There has been tried to apply unified assessment method using hot spot stress, which is effective to evaluate fatigue strength of fillet welded structures for ships and marine structures. This method can be applied to complicated structures and is independent of welding processes. In this study, first, stress analysis has been conducted for two-dimensional fillet welded joint models with various combinations of plate thickness and weld leg length of general fillet structures by means of boundary element method. Then, critical position, which is not affected by local stress concentration due to bead, was determined from the detailed stress distribution in the vicinity of weld toe. As a result, a general equation has been proposed to estimate the hot spot stress by one-point representative method. Second, the fatigue tests of typical fillet welded joints have been conducted by applying this method. Consequently, it was demonstrated that the unified fatigue strength can be evaluated by the S-N data based on hot spot stress range determined from the proposed equation, independent of structural stress concentration. 22 refs., 14 figs.

  11. 1998 report on results of technological development of super metal. Innovative technological development for producing advanced structure controlled metallic material (high-speed large reduction rolling technology); 1998 nendo super metal no gijutsu kaihatsu seika hokokusho. Kodo soshiki kozo seigyo kinzoku zairyo sosei gijutsu kaihatsu (kosoku daiatsuka atsuen gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A report was made on the 1998 results concerning technological development of super metal. In the 'research and development of super metal', metallurgical examination has been made on crystal grain super refining process using a machining simulator, with studies carried out on crystal grain refining by utilizing large-strain deformation with more than 50% deformation for a single pass and a diploid structure. As a result, it was found that the crystal grain size can be refined to approximately 1{mu}m. Consequently, in fiscal 1998, a high-speed large reduction rolling test equipment was developed capable of rendering a sheathing technology in a mechanically testable size by a rolling method. This test equipment has such capacity as the maximum load of 1,000 ton and the maximum torque of 95 ton/m and is a rolling mill whose scale is largest in the nation on the laboratory level. The rolling speed can be 120mpm, a very fast speed for a large sized rolling mill. Moreover, equipped with an immediate water cooling facility adjacent to the rolls and an automatic operating system for example, it is a high function rolling mill capable of cooling and rolling that render the complex and delicate sheathing technology of super metal. (NEDO)

  12. Energy supply/demand structure development survey project / comprehensive survey on energy supply/demand development. FY1997 survey on techniques for pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo / energy jukyu kodoka sogo chosa. 1997 nendo shoden hatsuden system no gijutsu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    Pyroelectric conversion systems were surveyed as the techniques for effective utilization of low-temperature waste heat sources. Described herein are the principle of pyroelectric power generation, including pyroelectric phenomenon, origin of pyroelectricity in polymers, and pyroelectric polymers and copolymers; utilization of the pyroelectric phenomenon, including hysteresis of pyroelectric materials, general pyroelectric conversion principle, pyroelectric conversion cycle, analysis of power output by an Olsen cycle, comparison with a steam engine, and power outputting methods; pyroelectric conversion systems, including heat regeneration method, plate type pyroelectric conversion devices using the heat regeneration method, and voltage controlling methods; and pyroelectric conversion outputting, including calculations of power output and loss, conduction-caused loss, pumping loss, and pyroelectric converter efficiency. Other items described herein include conceptual designs of 1 and 100 kW pyroelectric converters for utilization of waste heat, and current status of pyroelectric converter development at CANMET Energy Technology Center. (NEDO)

  13. Fiscal 2000 achievement report on the important regional technology research and development. Research and development of eco-tailored tribo-material creation process technology (Higher order composite structure material creation process); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Eco tailored tribo material sosei process gijutsu (koji fukugo kozo material sosei process gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop novel tribo-material creation processes through the application of an inclined constitution/structure control, a nonstoichiometric constitution control, or the like, to the manufacture of materials having excellent tribological characteristics for the purpose of improving on the performance of tribology related parts. In fiscal 2000, activities are conducted in the four fields of (1) the experimental manufacture of tribo-materials by powder sintering and the review of the process, (2) the experimental manufacture of tribo-materials by melting and the review of the process, (3) the experimental manufacture of brake disk materials and the review of the process, and (4) the experimental manufacture of bearing materials and the review of the process. In field (1), the preparation of an Fe{sub 3}Al/FeAl intermetallic compound powder by mechanical alloying and gas atomization and the conditions of pressure sintering by HIP (hot isostatic press) or the like are established. Concerning the melting method, basic techniques are established and an experimentally built rotor is evaluated for braking characteristics. In field (3), efforts are made to develop Cu/Sb free brake linings that will match TiAl-made rotors and then an MgO/C system is discovered, which is found to be on the same level as the conventional materials. (NEDO)

  14. Achievement report for fiscal 1998 on the development of super-metal technology. Development of technology of high corrosion-resistance iron base controlled microstructure materials; 1998 nendo super metal no gijutsu kaihatsu. Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    During ultrafine structure formation due to transformation from austenite to ferrite in an intense magnetic field, the transformation is accelerated by the thermodynamic stabilization of the ferrite phase which is ferromagnetic. The application of an intense magnetic field works effectively during the generation of nuclei. When a magnetic field is applied during reverse transformation, a honeycomb 2-phase structure is formed oriented toward the direction of the magnetic field and, when the structure is vertically compressed, the recrystallized structure is made ultrafine effectively. In pearlite transformation, hardening occurs when carbon atoms supersaturated in density are introduced in the presence of a magnetic field gradient, and curing further promotes precipitation hardening. In a ferrite complex phase system, wherein ultrafine globular cementite is uniformly distributed, plastic instability becomes explicit in a tensile test. There is a good possibility that an ultrafine structure recrystallization model may be built by calculation, into which the distribution of energy stored prior to recrystallizing nucleus formation is incorporated. The profile of a conceptual process of off-line or in-line integration of heavy-strain process and intense magnetic field application has become tangible. (NEDO)

  15. Mechanism of spark generation from Japanese toy firework (senko-hanabi). ; Structural-Oxidizing reaction of micro graphite crystals in molten K sub 2 Sn. Senko hanabi no jikkenteki kosatsu. ; Yoyu K sub 2 Sn chu no sekiboku bikessho no kozo teki sanka hanno

    Energy Technology Data Exchange (ETDEWEB)

    Ito, H. (The University, of Tokyo, Tokyo (Japan))

    1991-12-20

    Considerations were given on the spark generating mechanism of graphite particles in molten salt polysulfide through experiments on Japanese sparklers. The firework composition mixed consisted of two kinds: KNO{sub 3}, S, amorphous carbons, charcoal and lamp black, and K{sub 2}CO{sub 3}, S, charcoal and lamp black. The main constituent in fire balls is molten salt polysulfide. The O{sub 2} generated from combustion oxidizes C and S, whereas the generated K{sub 2}CO{sub 3} reacts with S to produce K{sub 2}Sn. In the KNO{sub 3} system, the calorific power reaches the maximum with lamp black contained at 10-15%. This is thought because the K{sup +} expands the space between the graphite crystal layers making the oxidation to take place more easily into their inner sides. On the one hand, the calorific power reduced with the lamp black at more than 16% would be because the lamp black clogging the crystalline spaces restricting the oxidation. It is thought that condensation and decomposition of micro graphite crystals occur simultaneously in the fire balls. It is also believed that the micro graphite crystals jumped out as a result of gas pressure from inside the crystals generated with the progress of oxidation break off at once because of the resistance of air together with the effect of the K{sup +} in the salt polysulfide (mutual separation of each layer). 9 refs., 6 figs., 1 tab.

  16. Report on technological achievements in fiscal 1999. Survey on geological structures in overseas countries, 'Japan-Vietnam joint coal exploration project on Red River delta'; 1999 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Vietnam sekitan kyodo tansa Red River delta project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-06-01

    With an objective to identify stratigraphy, geological structures, coal bed existing status, and coal quality of major coal beds in the north and central district of the area to be surveyed in the Red River delta, test well drilling, physical and seismic exploration, and coal composition analyses were performed. The area to be surveys is a typical delta where irrigation canals are running in all directions. Three test wells were drilled with drilling lengths of 640 m for TD3, 700 m for TD4 and 900 m for TD5. Coring was performed to depths greater than the Tertiary deposit. The seismic exploration was executed along three exploration lines. Total distance was 25 km. In addition, the VSP investigation was carried out on TD3 and TD5. The stratigraphy is composed from below of the Phu Cu bed (Neogene period: marine deposit) , the Tien Hung bed (Neogene period: continental deposit), and the Tai Doung bed (quaternary deposit), in which the bed that holds coal beds is the Tien Hung bed. The beds are very stable as the geological structure, but the constituting rocks are soft and fragile. Anticipated coal beds exist in depths greater than 1000 m. The coal quality is of low ash, low sulfur, medium in calorific power, and contains little gas. (NEDO)

  17. FY 1998 annual report on the results of new industry creation type industrial science and technology research and development on the research and development of supermetals. Development of techniques for controlling structures of nano-amorphous materials; 1998 nendo super metal no gijutsu kaihatsu. Nano amorphous kozo seigyo zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are the FY 1998 results of the development of techniques for controlling structures of nano-amorphous materials. For the development of techniques for finely dispersing fine particles, mechanical alloying (MA) and mechanical milling (MM) are investigated, to structure nano-crystals in common steel, for which hot isostatic pressing is evaluated as a consolidation process for the MA- and MM-prepared powders in the FY 1998. For researches on high-speed particle deposition and super plastic forming, an Al-Ni, Al-Fe and Al-Ti alloy are selected as the nano-structure materials to be prepared by evaporation, and various compositions of these systems are evaporated, in order to investigate their microstructures, mechanical properties and thermal stabilities. For researches on techniques for controlling phases with the aid of high-density energy, the R and D efforts are directed to exploration of composition of high resistance to corrosion by acid at dew point, preparation of non-equilibrium (e.g., amorphous) powders, and development of solidification and forming techniques, with the target of creation of an amorphous alloy showing corrosion resistance at least twice as high as that of the commercial corrosion-resistance material and formable into a bulk shape having a thickness of at least 1 mm. For researches on controlled cooling techniques, the basic data are collected. (NEDO)

  18. Study on unified fatigue strength assessment method for welded structure. Hot spot stress evaluating method for various combinations of plate thickness and weld leg length; Yosetsu kozo no toitsutekina hiro kyodo hyokaho ni kansuru kenkyu. Itaatsu to yosetsu ashinaga no kumiawase ni taisuru hot spot oryoku sanshutsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Nihei, K; Inamura, F; Koe, S [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1997-12-31

    There has been tried to apply unified assessment method using hot spot stress, which is effective to evaluate fatigue strength of fillet welded structures for ships and marine structures. This method can be applied to complicated structures and is independent of welding processes. In this study, first, stress analysis has been conducted for two-dimensional fillet welded joint models with various combinations of plate thickness and weld leg length of general fillet structures by means of boundary element method. Then, critical position, which is not affected by local stress concentration due to bead, was determined from the detailed stress distribution in the vicinity of weld toe. As a result, a general equation has been proposed to estimate the hot spot stress by one-point representative method. Second, the fatigue tests of typical fillet welded joints have been conducted by applying this method. Consequently, it was demonstrated that the unified fatigue strength can be evaluated by the S-N data based on hot spot stress range determined from the proposed equation, independent of structural stress concentration. 22 refs., 14 figs.

  19. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey of peripheral element technologies - Survey of novel voltaic cell structure solar cell development); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (shuhen yoso gijutsu ni kansuru chosa kenkyu - shinhatsuden soshi kozo taiyo denchi kaitaku no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The present state and trend are surveyed of organic ferroelectric thin films, new carbon materials, fullerene compounds, and thermophotovoltaic (TPV) power. In the study of organic ferroelectric thin-film solar cells, the effort still remains at the basic stage, with the conversion rate as low as 3% in Europe and 2% in Japan. The progress of basic studies, however, is worth attention. It is deemed that 15% is the photoconversion rate to be currently expected from new carbon material solar cells. Fullerene compounds include some semiconductors whose bandgap values may be controlled across a 0.75-1.95eV range, and they may find their place in thin-film solar cells. However, their physical properties are not fully known, and their development into devices such as solar cells is scarcely reported. The research and development of TPV in the U.S. is led by NASA (National Aeronautics and Space Administration) and NREL (National Renewable Energy Laboratory), with their efforts concentrated on the development of portable power sources utilizing combustion heat. In Europe, TPV application to small-scale residential cogeneration systems is under study. (NEDO)

  20. Fiscal 1999 R and D project for industrial science and technology. R and D of technology for creating innovative and high-functional material - development of technology for structural control material (Report on result of R and D of harmonized molecular material); 1999 nendo dokusoteki kokino zairyo sosei gijutsu no keknkyu kaihatsu seika hokokusho. Kozo seigyo zairyo gijutsu kaihatsu (bunshi kyocho zairyo no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With the aim of contributing to the development of optical elements, devices, sensors, high performance catalysts, etc., R and D was conducted on fundamental technologies for creating materials using harmonized molecular actions, and the fiscal 1999 results were reported. In the R and D of self-assembled molecular film materials, an electric-field sensitive self-assembled molecular film was experimentally manufactured, as were self-assembling electroluminescent and lyotropic liquid crystal pigmentary film materials. In the R and D of mesophase materials, for rod-like liquid crystal systems, a material was successfully developed possessing a transparency of 90% in the visible region accompanied with an optical phase difference of 4.0 microns. For disk-like liquid crystal systems, a diminishing tendency of obtainable photoelectric current was confirmed even with a small change in the orientation after photopolymerization. In the R and D of microporous materials, synthesis was performed for system-controlled metallosilicates and shape-controlled microporous materials. Further, structural correlation was examined for organic templates and microporous materials. (NEDO)

  1. Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Research and development concerning relations between sintered body textural structure and material characteristics in fine ceramics); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (fine ceramics no shoketsutai soshiki kozo to zairyo tokusei tono kankei ni kansuru kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development was carried out involving fine ceramic sintered body textural structure evaluation methods for the development of process technologies for achieving higher quality and lower cost. Studies centered about a method for evaluating coarse pores and coarse grains in sintered bodies, relations between sintered body fracture strength and textural structure, and the standardization of evaluation methods. As the result, an evaluation method for observing pore structures in a sintered body flake specimen under an optical microscope and another for observing coarse grains under a polarization microscope were proposed. As for the effect of coarse defects on the fracture strength of ceramics, it was demonstrated experimentally and theoretically that coarse defects several tens of micrometers in size greatly affected the fracture strength. In the study of methods for sintered body grain size evaluation, findings were obtained about the processing of the specimen surface. (NEDO)

  2. 1998 report on results of R and D project for industrial science and technology (R and D for technologies of producing innovative high performance material) (development of technologies for structural control material). R and D for high stimuli-responsive material; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A report was made on the results of 1998 R and D concerning high stimuli-responsive materials. This R and D was intended to develop technologies for producing, by copying organism, innovative new stocks and new materials which repeatedly provide functions such as separating, transmitting and moving in response to stimuli. In the R and D of polymeric high stimuli-responsive materials, studies were conducted on multi-stimuli-responsive separation materials, molecular recognition controlled separation materials, and cell adhesion/separation materials with molecular recognition function. In the R and D of composite high stimuli-responsive materials, release controlled function materials and materials for actuator were studied. The investigation and research of common basic technologies were carried out on such subjects as synthesis and functional development of multi-signal responded polymer gels, development of temperature-responsive chromatography, synthesis and characterization of novel stimuli-sensitive materials, studies on structural characterization of intelligent gels, novel thermosensitive polymers, polyelectrolytic model networks, etc. (NEDO)

  3. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (development of precise structure control materials for enhancement of oil refining); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the R and D of technologies for creating original high-functional materials under the R and D system of industrial scientific technology. Japan chemical Innovation Institute (JCII) is conducting intensive joint researches under consignment from NEDO with private companies, universities and national research institutes. Among those, the paper reported the fiscal 1997 results of the following two researches conducted as development of precise structure control materials for enhancement of oil refining: precision catalytic polymerization and multi-dimensional space polymer. As to the precision catalytic polymerization, the paper is aimed at developing base technologies for the molecular weight and stereoregularity by which remarkable improvement in performance of addition polymerization type polymer can be expected, and on the development of a polymerization catalyst which arbitarily controls the primary structure such as end group structure and of a precision addition polymerization process. Subthemes are addition polymerization with limit and oriented catalytic polymerization. In relation to multi-dimensional space polymer, the paper is aimed at developing highly selective polymerization technology of aromatic compounds using enzyme related catalysts and synthesis technology of regular structure polymer, and synthesis technology of new polymer group having a new chain pattern except covalent bond/new polymer group having characteristics in three-dimensional space geometric structure. 244 refs,, 160 figs., 94 tabs.

  4. Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of building material integrated solar cell modules - modules with new multi-layer structure); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (shinfukuso kozo module))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Development is being made on a panel type module that can be used together with an air bubble concrete board (ALC board), and is provided with design characteristics. The development work includes trial fabrication and evaluation of a module with new multi-layer structure, and development of a technology to unitize cells and submodules, and a systematizing method. In the trial fabrication and evaluation, flame retardant and uninflammable modules using fluororesin, and modules with as large area as 4 m{sup 2} were fabricated on a trial basis, in addition to the modules with the basic structure. These modules were given evaluations on such wall material properties as wind pressure resistance, heat and cracking resistance, and fire resistance. In a deformation resistance test considering the integrated use with the ALC board, the developed modules showed a good result. In developing the cells with design characteristics, discussions were given on the inter-cell wiring methods. Development was made on a method to establish a unit structure based on the design and size of a building. In developing the systematization method, the trial fabrication method was applied to a module with lamination structure, a module integrated with the ALC board, and a large-area hollow module to have fabricated the top-light spandrels. (NEDO)

  5. FY 2000 report on the results of the research and development project for utilization of information of high-molecular-weight structures in a living body. Survey on the technological trends of utilizing the reactions with metals in a living body; 2000 nendo seitai kobunshi kozo joho riyo gijutsu kaihatsu chosa hokokusho. 'Seitai kinzoku hanno riyo gijutsu' ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the survey on the technological trends of utilizing the reactions with metals in a living body, noting the bio-processes effectively coping with the environmental problems. The effects of heavy metals on microorganisms have been investigated on the molecular biology level, but are not fully elucidated. Recently, the microorganisms capable of converting inorganic metal ions in water into the insoluble compounds have been known, leading to possibility of bioremediation to solve pollution by heavy metals, which have detrimental effects on human health. Heavy metals must be recovered, because they are not extinct by decomposition. The plant aided purification has been attracting attention to cope with heavy metals accumulated in soil. Application of bacteria-aided leaching, which is adopted as one ore smelting process, to the technologies for utilizing metals in a living body has been expected, because diversified activities of inanimate matters in extreme environments have been known. Recently, bio-machining of metals aided by Thiobacillus ferrooxidans, one species of independent nutrient bacteria capable of eating metals, has been developed to a potentially viable stage. (NEDO)

  6. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Research and survey of peripheral element technologies (Research and survey for development of solar cell of new power generation device structure); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu / shuhen yoso gijutsu ni kansuru chosa kenkyu (shinhatsuden soshi kozo taiyo denchi kaitaku no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Attention is paid to behavior at the molecular level with reference taken to the photosynthetic mechanism, and a behavioral mechanism is proposed, which incorporates, in place of the conventional band model, a concept of a molecular structure based on electron transfer, excitation energy transfer, and reactions of oxidation and reduction. Discussion is then made on elements of technology development for the embodiment of high-efficiency organic ferroelectric thin-film solar cells. The elements taken up include the feasibility of organic ferroelectric thin-film cells, photoelctric conversion systems of plants and photosynthetic bacteria, solar cells using donor-acceptor type dyes, organic thin-film solar cells using conductive polymers, and efficient photoexcitation of organic dyes. Fullerene compounds are semiconductive and their band gaps may be controlled to stay within the range of 0.75-1.9eV, and this justifies a hope that they will serve as solar cells. As for TPV (thermophotovoltaic) conversion, it is under development mainly at NASA (National Aeronautics and Space Administration) as a transportable power source based on heat of combustion. Efforts are also being exerted since 1990 in five European countries to develop TPV systems for small-scale cogeneration. (NEDO)

  7. Achievement report for fiscal 1998 on research and development of technologies for creating high-performance materials under the industrial and scientific technology research and development project. Control of condensation-based precision structures (High-performance materials for power plant facilities); 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) shukugokei seimitsu kozo seigyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The goal is to prepare a base for the development of polymerizing catalysts and precision polymerization processes which will enable the arbitrary control of molecular weight, regularity, branching, and primary structures such as terminal groups, which effort will lead to a remarkable advancement in condensation polymerization and open-ring polymeric material performance. Endeavors are on to fulfill two separate purposes, that is, precision condensation polymerization and controlled open-ring polymerization. In the study of precision condensation polymerization, at issue are basic studies and the development of precision control technologies for arrangement, molecular weight, branching, and matrix condensation polymerization. Also at issue are the development of technologies of position selective oxidization polymerization and precision conjugate high-molecular condensation synthesis. Concerning open-ring control polymerization, precision control technologies will be developed involving branching, molecular weight, crosslinking, arrangement, and the structure of cyclocarbonate open-ring polymerization. Open-ring control polymerization technologies are also under study by use of organic metal complexes. A survey of technological trends is also explained. (NEDO)

  8. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development of novel type solar cell module integratable with building materials - Novel multilayer structure module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu - shinfukuso kozo module)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The project aims to develop solar cell modules of a novel multilayer structure, based on the resin filling structure, hollow structure, and the laminate structure, and integratable with building materials. In fiscal 1999, for the development of cells and submodule structures, cells and submodules were fabricated which were usable with various specimens. In the case of design oriented cells, electrode structures and linkage methods were improved for the enhancement of power generation performance, and a hollow structure and a laminate structure were fabricated. As for the 4m{sup 2}-large module (laminate structure), a specimen with dummy cells arranged along its periphery was fabricated. For cost reduction, a study was made about a module (laminate structure) integrated with an ALC (autoclaved lightweight concrete) board, and the kind of surface glass, cell arrangement, and back sheet types and their respective designs were evaluated. It was then concluded that the module was fit for practical application. The module was then checked for wind endurance in a wind endurance test, for electric characteristics, and for flame inhibition capability in a fire prevention/resistance test. (NEDO)

  9. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture applied type thin film solar cells with new structure and development of high-efficiency hybrid thin film/sheet solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (oyogata shin kozo usumaku taiyo denchi no seizo gijutsu kaihatsu (kokoritsu hybrid gata usumaku / sheet taiyo denchi no seizo gijutsu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to develop low-cost and high-efficiency hybrid thin film/sheet solar cells, research and development has been performed. This paper summarizes the achievements in fiscal 1999. The research is related to a hybrid construction, in which the upper cells of amorphous silicon thin film are formed on the lower cells bonded with micro-crystalline silicon thin film relative to a poly-crystalline silicon sheet. In the technology to form the upper cells, a pin-construction using amorphous silicon thin film made by using the plasma CVD process was adopted, whereas an open circuit voltage of 1.45V, a short circuit current of 13.6 mA/cm{sup 2}, and a conversion efficiency of 13.5% were obtained. In the technology to form the substrate for the lower cells, formation of flat silicon thin plate that can be peeled off was identified as a result of adopting the construction in which a graphite substrate is provided on a rotating cooling body of 12-prism type. With regard to the technology to bond and form the lower cells, electrical properties of hetero-bonded cells were discussed, and an open circuit voltage of 0.605V and a conversion efficiency of 14.3% were obtained as a result of enhancing the film quality and optimizing the film thickness. (NEDO)

  10. Fiscal 1997 project on the R and D of industrial scientific technology under consignment form NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of molecular harmonized materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) bunshi kyocho zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    By establishing microtechnology using molecular-level bottoming-up (molecular harmonization) by imitating the system of living organism, the paper described the R and D of molecular harmonized materials aiming at developing high-functional/high-performance materials such as high-performance catalyst, photo-information functional materials and sensing materials. Under consignment from NEDO, Japan Chemical innovation Institute started the 5-year plan in fiscal 1997. Self-assembled molecular films, in which organic molecules are orderly arranged by self-assembly, aim at developing new memory/optical/sensing materials. Mesophase materials which are such materials as liquid crystal showing the intermediate state between solid and liquid, develop optical/photoconductive materials using precise molecular orientation controllability. Macroporous materials are such substances as zeolite having molecular size micro pores. The paper aims at establishment of synthesis techniques of them and development of high-performance catalyst, etc. using them. In the comprehensive investigational research, conducted was a survey of the trend overseas in addition to a study of subjects in question. Further, the supporting basic study was reconsigned to universities, etc. 57 refs., 62 figs., 17 tabs.

  11. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of multi-stimuli-responsive materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described multi-stimuli-responsive materials out of the technology developments for creating original high-functional materials under the system of R and D of industrial scientific technologies. These are materials which repeatedly reproduce functions such as separation, penetration and movement in response to stimuli by imitating living organisms. In relation to polymer multi-stimuli-responsive materials, various copolymers were synthesized using N-acetyl (meta) acrylamide, of which the synthesis method was established in the previous fiscal year, as a main component, and thermal responsive polymer with upper critical solution temperature which becomes a base of separation functional materials was searched for. By immobilizing it with molecular recognition ligand, measured was thermal dependence of affinity of the immobilized matter to albumin. Also studied were molecular recognition cell adhesion/separation functional materials. Concerning composite multi-stimuli-responsive materials, with the use of silica microcapsule surface-immobilized with silane coupling agent, studied were the optimum conditions for immobilizing thermo-responsive polymer to the surface of the capsule. Using motion functional materials by ion exchange resin, obtained was motion functionality which is satisfactory at the state of practical use. 94 refs., 82 figs., 16 tabs.

  12. The Nishino Breathing Method and Ki-energy (Life-energy): A Challenge to Traditional Scientific Thinking

    Science.gov (United States)

    Ohnishi, S. Tsuyoshi; Ohnishi, Tomoko

    2006-01-01

    The breathing method, which was developed and is being taught by Kozo Nishino, a Japanese Ki-expert, is for raising the levels of Ki-energy (life-energy or the vitality) of an individual. It is neither a therapy nor a healing technique. However, many of his students have experienced an improvement in their health, and in some cases, they were able to overcome health problems by themselves. Since this is an interesting subject from the standpoint of complementary and alternative medicine (CAM), we have been collaborating with Nishino to conduct a scientific investigation of his Ki-energy. We found that Nishino's Ki-energy can inhibit cell division of cancer cells, protect isolated mitochondria from heat deterioration and reduce lipid peroxidation in heat-treated mitochondria. Although Ki-energy may consist of several different energy forms, we found that at least one of them is near-infrared radiation between the wavelength range of 0.8 and 2.7 µm. Another interesting observation at his school is the Taiki-practice (paired Ki-practice). During this practice, Nishino can ‘move’ his students without any physical contact. Many of them run, jump or roll on the floor when they receive his Ki-energy. We studied this and propose that ‘information’ is conveyed through the air between two individuals by Ki-energy. This may be called a five sense-independent, life-to-life communication by Ki. All of our results suggest that we should re-evaluate the Cartesian dualism (separation of mind and body) which has been a fundamental principle of modern science for the past three centuries. PMID:16786048

  13. The Nishino Breathing Method and Ki-energy (Life-energy: A Challenge to Traditional Scientific Thinking

    Directory of Open Access Journals (Sweden)

    Tsuyoshi Ohnishi

    2006-01-01

    Full Text Available The breathing method, which was developed and is being taught by Kozo Nishino, a Japanese Ki-expert, is for raising the levels of Ki-energy (life-energy or the vitality of an individual. It is neither a therapy nor a healing technique. However, many of his students have experienced an improvement in their health, and in some cases, they were able to overcome health problems by themselves. Since this is an interesting subject from the standpoint of complementary and alternative medicine (CAM, we have been collaborating with Nishino to conduct a scientific investigation of his Ki-energy. We found that Nishino's Ki-energy can inhibit cell division of cancer cells, protect isolated mitochondria from heat deterioration and reduce lipid peroxidation in heat-treated mitochondria. Although Ki-energy may consist of several different energy forms, we found that at least one of them is near-infrared radiation between the wavelength range of 0.8 and 2.7 µm. Another interesting observation at his school is the Taiki-practice (paired Ki-practice. During this practice, Nishino can ‘move’ his students without any physical contact. Many of them run, jump or roll on the floor when they receive his Ki-energy. We studied this and propose that ‘information’ is conveyed through the air between two individuals by Ki-energy. This may be called a five sense-independent, life-to-life communication by Ki. All of our results suggest that we should re-evaluate the Cartesian dualism (separation of mind and body which has been a fundamental principle of modern science for the past three centuries.

  14. Lung function and blood markers of nutritional status in non-COPD aging men with smoking history: A cross-sectional study

    Directory of Open Access Journals (Sweden)

    Nobuyoshi Shiozawa

    2010-07-01

    Full Text Available Nobuyoshi Shiozawa1, Kanae Hayashimoto2, Etsuji Suzuki5, Hiroshi Kikuchi3, Shingo Takata3, Kozo Ashida3, Masutaka Watanabe4, Yasuhiro Hosaki6, Fumihiro Mitsunobu1,31Department of Geriatric Medicine, Graduate School of Medicine, Dentistry and Pharmaceutical Sciences, Okayama University, Misasa, Tottori, Japan; 2Nutrition Support Service and Divisions of 3Internal Medicine and 4Rehabilitation, Okayama University Hospital Misasa Medical Center, Misasa, Tottori, Japan; 5Department of Epidemiology, Graduate School of Medicine, Dentistry and Pharmaceutical Sciences, Okayama University, Okayama, Japan; 6Division of Internal Medicine, Hiroshima Teishin Hospital, Hiroshima, JapanPurpose: Cigarette smoking and advanced age are well known as risk factors for chronic obstructive pulmonary disease (COPD, and nutritional abnormalities are important in patients with COPD. However, little is known about the nutritional status in non-COPD aging men with smoking history. We therefore investigated whether reduced lung function is associated with lower blood markers of nutritional status in those men.Subjects and methods: This association was examined in a cross-sectional study of 65 Japanese male current or former smokers aged 50 to 80 years: 48 without COPD (non-COPD group, divided into tertiles according to forced expiratory volume in one second as percent of forced vital capacity (FEV1/FVC, and 17 with COPD (COPD group.Results: After adjustment for potential confounders, lower FEV1/FVC was significantly associated with lower red blood cell count (RBCc, hemoglobin, and total protein (TP; not with total energy intake. The difference in adjusted RBCc and TP among the non-COPD group tertiles was greater than that between the bottom tertile in the non-COPD group and the COPD group.Conclusion: In non-COPD aging men with smoking history, trends toward reduced nutritional status and anemia may independently emerge in blood components along with decreased lung function

  15. PREFACE: MEM07: The 5th Annual Workshop on Mechanical and Electromagnetic Properties of Composite Superconductors (Princeton, NJ, USA, 21 24 August 2007)

    Science.gov (United States)

    Larbalestier, D. C.; Osamura, K.; Hampshire, D. P.

    2008-05-01

    -up is a second vital task. As system design is dependent on material development, there is a critical need to study the key issues in developing high performance superconducting materials. The emphases of MEM07 were The mechanical properties of superconductors including the influence of stress and strain on the critical current of practical conductors including YBCO and ReBCO coated conductors, BSCCO tapes, MgB2 wires and Nb3Sn filamentary conductors. The intrinsic strain effects on critical current density in Nb3Sn, YBCO, BSCCO and MgB2. Recent advances in critical current, the mechanical properties and the reduction in ac losses of HTS tapes and wires. The compositional and microstructural dependence of E-J characteristics and explanations based on flux pinning, grain boundary weak-links and other mechanisms. Standardized test-methods: international cooperative research work to establish test methods for assessing the mechano-electromagnetic properties of superconductors based on the activities of IEC/TC90 and VAMAS/TWA-16. More than 60 researchers from more than 12 countries attended the MEM07 workshop, and about 40 presentations were made. A small selection of papers (15) from the workshop are included in this special issue of Superconductor Science and Technology. Taken together with papers published at earlier MEM meetings, this issue provides an updated view of some of the current state-of-the-art research in the mechano-electromagnetic properties of composite superconductors. The workshop was organized under the activities of the NEDO Grant Project (Applied Superconductivity, 2004EA004) and VAMAS/TWA-16. The meeting was organized by a committee composed of David Larbalestier (Conference Chair) aided by MEM05 and MEM06 Conference Chairs Kozo Osamura (Research Institute for Applied Sciences, Kyoto, Japan), Damian Hampshire (Durham University, UK) and Arman Nyilas (CEME). The Program Committee was composed of Ettore Salpietro (European Fusion Development Agreement

  16. Preface

    Science.gov (United States)

    2003-09-01

    stresses, electromagnetic force, and mechanical and thermal cycling. • Mechanical properties: tensile and compressive properties, fatigue characteristics and fracture behaviour. • Thermal properties: thermal conductivity, thermal dilatation and thermal strain. • Modelling: prediction of critical current and mechanical properties of composite superconductors through statistical analysis, finite element analysis, etc. • Test methods: international cooperative research work to establish test methods for assessing mechano-electromagnetic properties based on the activity of VAMAS/TWA-16. This discussion took place with respect to three types of composites: • MFC (multifilamentary composite): BSCCO, MgB2, Nb-Ti, Nb3Sn and Nb3Al. • CCC (coated conductor composite): YBCO and ReBCO. • BCC (bulk crystal composite): YBCO and ReBCO. More than 55 researchers attended the MEM03 workshop, coming from eight different countries. A total of 42 papers were presented. In this special issue of Superconductor Science and Technology selected papers have been included that are concerned with the comprehensive scientific research subjects mentioned above. The aim of this issue is to provide a snapshot of some of the current state-of-the-art research and to promote further research into the mechano-electromagnetic properties of composite superconductors. The workshop was organized under the activities of NEDO technology quest and VAMAS/TWA-16. We wish to thank the following for their contribution to the success of the workshop: NEDO Super-ACE project, AFOSR, AOARD and IEC/TC90-JNC. Guest Editors: Kozo Osamura Hitoshi Wada Arman Nyilas Damian Hampshire