Investigations of CR39 dosimeters for neutron routine dosimetry

International Nuclear Information System (INIS)

Weinstein, M.; Abraham, A.; Tshuva, A.; German, U.

2004-01-01

CR-39 is a polymeric nuclear track detector which is widely used for neutron dosimetry. CR-39 detector development was conducted at a number of laboratories throughout the world(1,2) , and was accepted also for routine dosimetry. However, there are shortcomings which must be taken into consideration the lack of a dosimetry grade material which causes batch variations, significant angular dependence and a moderate sensitivity. CR-39 also under-responds for certain classes of neutron spectra (lower energy neutrons from reactors or high energy accelerator-produced neutrons).In order to introduce CR-39 as a routine dosimeter at NRCN, a series of checks were performed. The present work describes the results of some of our checks, to characterize the main properties of CR-39 dosimeters

INAA of polyacrylic hydrogels of pharmaceutical grade

International Nuclear Information System (INIS)

Ponta, C.; Salagean, M.; Pantelica, A.; Georgescu, I.I.

1998-01-01

Polyacrylic acid (PA) and its salts are promising biomaterials used in the pharmaceutical industry. They could be used as pharmaceutical additives, as a burn dressing and also in the slow released implants or trans-derma patch formulations. Polyacrylic acid of pharmaceutical grade can be obtained by gamma irradiation polymerization. The influence of the raw materials and of the technological procedure on the final product purity has been investigated by Instrumental Neutron Activation Analysis (INAA) method. The following materials have been analyzed by INAA: 1) acrylic acid of technical grade; 2) acrylic acid purified by double crystallisation; 3) NaOH of analytical grade; 4) CaCl-2·6H 2 O of pharmaceutical grade; 5) CaCl 2 ·2H 2 O of analytical grade; 6) granulated PANa; 7) ungranulated PANa; 8) ungranulated PANaCa; 9) PANaCa granulated by milling in IFIN-HH using the mill nr. 1; 10) PANaCa granulated by milling in Institute of Chemical and Pharmaceutical Research (ICPR); 11) PANaCa granulated by milling in IFIN-HH using the mill nr. 2. The first five samples, marked from 1 to 5, are raw materials and the other six samples, marked from 6 to 11, are the final polyacrylic structures processed by various technological procedures. The samples together with the appropriate reference materials have been irradiated at WWR-S reactor in a neutron flux of 2.5·10 12 cm -2 s -1 and the induced radioactivity was registered by a HPGe detector (EG/G ORTEC) of 30% efficiency and 2.1 keV resolution. The concentrations of As, Br, Ce, Co, Cr, Fe, La, Sb, Sc, Zn have been determined. For the final polyacrylic structures, except for granulated PANa (sample 6), only the elements Co, Cr, Fe, Sc, Zn were found at the following concentration levels: tens of ppm (Co), ppm (Zn), hundreds of ppb (Cr), tens of ppb (Co), ppb (Co, Sc), 10 -1 ppb (Sc). In the granulated PANa, in comparison with the other analyzed final products, similar concentration values were found for Fe, Sc and Zn

Preoperative concurrent chemoradiotherapy for advanced oral cancer. Did the cancer cells really disappear in the CR cases?

International Nuclear Information System (INIS)

Kirita, Tadaaki; Yamanaka, Yasutsugu; Imai, Yuichiro; Aoki, Kumiko; Inoue, Masahide; Yagyuu, Takahiro

2008-01-01

We report a series of 136 patients with advanced oral cancer who received preoperative concurrent chemoradiotherapy (CCRT) followed by surgery and who were studied clinically and histopathologically, and the indication of minimally invasive surgery was evaluated. The results and conclusions were as follows: The CR (complete response) of the primary tumor was 60.3% and the overall response rate was 92.7%. Histological effects were Grade IIb and above, i.e. effective, in 84.6% and Grade III, IV, i.e. pathological CR, in 73 of 82 (89.0%) in CR cases. The CCRT was also very effective histologically, and a correlation was observed between clinical effects and histological effects. The residual tumor grade (R Grade) in the resected specimen is considered to be useful as a prognostic factor. Histological effects were satisfactory in good partial response (PR) and CR cases on CCRT. In such cases, minimally invasive surgery is considered to be applicable even in advanced cases, and improvements in the postoperative quality of life (QOL) can be expected by preservation of the oral organs and functions. (author)

Contribution of deformation mechanisms to strength and ductility in two Cr-Mn grade austenitic stainless steels

Energy Technology Data Exchange (ETDEWEB)

Hamada, A.S., E-mail: atef_saleh@s-petrol.suez.edu.eg [Materials Engineering Laboratory, Box 4200, University of Oulu, 90014 Oulu (Finland); Metallurgical and Materials Engineering Department, Faculty of Petroleum and Mining Engineering, Suez Canal University, Box 43721, Suez (Egypt); Karjalainen, L.P. [Materials Engineering Laboratory, Box 4200, University of Oulu, 90014 Oulu (Finland); Misra, R.D.K. [Center for Structural and Functional Materials and Chemical Engineering Department, University of Louisiana at Lafayette, P.O. Box 44130, Lafayette, LA 70504-4130, USA. (United States); Talonen, J. [Outokumpu Oyj, Box 140, FI-02201 Espoo (Finland)

2013-01-01

The role of different deformation mechanisms in controlling mechanical properties were studied in two low-Ni, Cr-Mn austenitic stainless steel grades (Types 201 and 201L) by tensile testing and microstructure examinations. Tensile tests were carried out at two different strain rates, 5 Multiplication-Sign 10{sup -4} and 10{sup -2} s{sup -1}, in the temperature range from -80 Degree-Sign C to 200 Degree-Sign C. It was observed that the flow properties and work hardening rate are affected significantly by temperature and strain rate for the concerned steels through variation of deformation mechanism. Deformation-induced austenite-to-martensite transformation (TRIP effect) is the dominant mechanism at temperatures below room temperature. From 50 Degree-Sign C up to 200 Degree-Sign C, plastic deformation is controlled by mechanical twinning (TWIP effect) and dislocation glide. The electron backscattered diffraction (EBSD) technique and transmission electron microscopy (TEM) were employed to study the plastic deformation accommodation and identify the primary deformation mechanisms operating in the deformed steels.

Functionally Graded Material: An overview

CSIR Research Space (South Africa)

Mahamood, RM

2012-07-01

Full Text Available -3146. [50] X. Jin, L. Wu, L. Guo, H. Yu, and Y. Sun, ?Experimental investigation of the mixed-mode crack propagation in ZrO2/NiCr functionally graded materials,? Engineering Fracture Mechanics, vol. 76(12), (2009), pp. 1800-1810. [51] Z. Cheng, D. Gao... by stable crack growth,? Engineering Fracture Mechanics, vol.72(15), (2005), pp. 2359-2372. [47] Z.-H. Jin, and R.H. Dodds Jr, ?Crack growth resistance behavior of a functionally graded material: computational studies,? Engineering Fracture Mechanics...

Selective surface oxidation and segregation upon short term annealing of model alloys and industrial steel grades

Energy Technology Data Exchange (ETDEWEB)

Swaminathan, S.

2007-07-01

Segregation and selective oxidation phenomena of minor alloying elements during annealing of steel sheets lead to the formation of bare spots after hot-dip galvanizing. This thesis highlights the influence of annealing conditions and the effect of alloying elements on the selective oxidation in model alloys and some industrial steel grades. Model alloys of binary (Fe-2Si, Fe-2Mn, Fe-0.8Cr), ternary (Fe-2Mn-2Si, Fe-2Mn-0.8Cr, Fe-1Mn-0.8Cr, Fe-1Si-0.8Cr, Fe-2Si-0.8Cr) and quarternary (Fe-2Mn-2Si-0.8Cr) systems were studied. In the case of steels, standard grade interstitial free (IF) steels and experimental grade tensile strength 1000 MPa steel were investigated. All specimens were annealed at 820 C in N{sub 2}-5%H{sub 2} gas atmospheres with the wide range of dew points (i.e. -80 to 0 C). The surface chemistry after annealing and its wettability with liquid Zn have been correlated as a function of dew points by simulating the hot-dip galvanizing process at laboratory scale. (orig.)

The effects of graded levels of calorie restriction: VI. Impact of short-term graded calorie restriction on transcriptomic responses of the hypothalamic hunger and circadian signaling pathways.

Science.gov (United States)

Derous, Davina; Mitchell, Sharon E; Green, Cara L; Chen, Luonan; Han, Jing-Dong J; Wang, Yingchun; Promislow, Daniel E L; Lusseau, David; Speakman, John R; Douglas, Alex

2016-04-01

Food intake and circadian rhythms are regulated by hypothalamic neuropeptides and circulating hormones, which could mediate the anti-ageing effect of calorie restriction (CR). We tested whether these two signaling pathways mediate CR by quantifying hypothalamic transcripts of male C57BL/6 mice exposed to graded levels of CR (10 % to 40 %) for 3 months. We found that the graded CR manipulation resulted in upregulation of core circadian rhythm genes, which correlated negatively with circulating levels of leptin, insulin-like growth factor 1 (IGF-1), insulin, and tumor necrosis factor alpha (TNF-α). In addition, key components in the hunger signaling pathway were expressed in a manner reflecting elevated hunger at greater levels of restriction, and which also correlated negatively with circulating levels of insulin, TNF-α, leptin and IGF-1. Lastly, phenotypes, such as food anticipatory activity and body temperature, were associated with expression levels of both hunger genes and core clock genes. Our results suggest modulation of the hunger and circadian signaling pathways in response to altered levels of circulating hormones, that are themselves downstream of morphological changes resulting from CR treatment, may be important elements in the response to CR, driving some of the key phenotypic outcomes.

The diagnostic performance of magnetic resonance spectroscopy in differentiating high-from low-grade gliomas: A systematic review and meta-analysis

International Nuclear Information System (INIS)

Wang, Qun; Zhang, JiaShu; Wu, Chen; Li, FangYe; Chen, XiaoLei; Xu, BaiNan; Zhang, Hui; Zhu, WeiJie

2016-01-01

Magnetic resonance spectroscopy (MRS) is a powerful tool for preoperative grading of gliomas. We performed a meta-analysis to evaluate the diagnostic performance of MRS in differentiating high-grade gliomas (HGGs) from low-grade gliomas (LGGs). PubMed and Embase databases were systematically searched for relevant studies of glioma grading assessed by MRS through 27 March 2015. Based on the data from eligible studies, pooled sensitivity, specificity, diagnostic odds ratio and areas under summary receiver operating characteristic curve (SROC) of different metabolite ratios were obtained. Thirty articles comprising a total sample size of 1228 patients were included in our meta-analysis. Quantitative synthesis of studies showed that the pooled sensitivity/specificity of Cho/Cr, Cho/NAA and NAA/Cr ratios was 0.75/0.60, 0.80/0.76 and 0.71/0.70, respectively. The area under the curve (AUC) of the SROC was 0.83, 0.87 and 0.78, respectively. MRS demonstrated moderate diagnostic performance in distinguishing HGGs from LGGs using tumoural metabolite ratios including Cho/Cr, Cho/NAA and NAA/Cr. Although there was no significant difference in AUC between Cho/Cr and Cho/NAA groups, Cho/NAA ratio showed higher sensitivity and specificity than Cho/Cr ratio and NAA/Cr ratio. We suggest that MRS should combine other advanced imaging techniques to improve diagnostic accuracy in differentiating HGGs from LGGs. (orig.)

Academic Success of Urban African American Elementary Students in Title I Schools

Science.gov (United States)

Anderson, James Sebastian

2017-01-01

The researcher investigated the achievement of third- and fifth-grade urban African American students who attended science, technology, engineering, and mathematics (STEM), Non-STEM, and Theme Title I schools in science and mathematics on the 2015 Georgia Milestones Assessment. The researcher used data from 29 Non-STEM, 14 STEM, and 10 Theme…

A Weakest-Link Approach for Fatigue Limit of 30CrNiMo8 Steels (Preprint)

Science.gov (United States)

2011-03-01

34Application of a Weakest-Link Concept to the Fatigue Limit of the Bearing Steel Sae 52100 in a Bainitic Condition," Fatigue and Fracture of...AFRL-RX-WP-TP-2011-4206 A WEAKEST-LINK APPROACH FOR FATIGUE LIMIT OF 30CrNiMo8 STEELS (PREPRINT) S. Ekwaro-Osire and H.V. Kulkarni Texas...2011 4. TITLE AND SUBTITLE A WEAKEST-LINK APPROACH FOR FATIGUE LIMIT OF 30CrNiMo8 STEELS (PREPRINT) 5a. CONTRACT NUMBER In-house 5b. GRANT

Comparing the characteristics of highly cited titles and highly alted titles

Energy Technology Data Exchange (ETDEWEB)

Didegah, F.; Bowman, T.D.; Bowman, S.; Hartley, J.

2016-07-01

This study examines differences in the types of titles for articles that show high altmetric activity (highly alted articles) versus highly cited articles. This work expands on previous research on document titles in combination with a grounded theory approach to develop a codebook in which articles were manually coded based on 11 characteristics. The results show that there are differences and similarities in titles across many of the examined characteristics; highly cited titles and highly mentioned titles on Wikipedia have some similar characteristics such as they have the the highest percentage of substantive words; in addition, there are no or very few titles referencing outside or with humor/lightness on both platforms. Twitter and Facebook also showed some similarities having the highest percentage of humorous/light titles and lowest percentage of substantive words in their titles. (Author)

Superficial characterization and nano structural of nano multilayers Cr/Cr N obtained by UBM with different unbalance grades

International Nuclear Information System (INIS)

Piratoba, U.; Arenas A, J.; Olaya, J. J.

2013-01-01

Coatings of 25 bilayers of Cr/Cr N, with total thickness between 1.32 and 1.67 microns, were deposited by reactive sputtering on silicon and H13 steel, in argon and argon with nitrogen atmospheres. A power of 160 watts, flows of argon and nitrogen of 9 and 3 sc cm respectively, and an axial unbalanced magnetron, whose coefficient of geometrical unbalance K G was varied between 0.85 and 1.37. Of these coatings, micrographs of surface and cross section scanning electron microscopy were obtained, was make a micro structural characterization with X-ray diffraction, a nano structural characterization by transmission electron microscopy, and surface characterization by atomic force microscopy in tapping mode: analysis showed uniform surface coating with globular and pyramidal formations, which contain some granular inclusions and microscopic craters. With the increase in the unbalance of the magnetic field, the grain size, the roughness and the speed of the coatings growth were increased. (Author)

PA03.13. Effect of triphaladi rasayana along with yoga therapy on low grade non hodgkins lymphoma and resistant intermediate and high grade non hodgkins lymphoma

Science.gov (United States)

Soumya, MS Surya; Sarasa, TP

2013-01-01

Purpose: 1. To find out the effect of Thriphaladi Rasayana along with Yoga Therapy on low grade Non Hodgkins Lymphoma and resistant intermediate and high grade NonHodgkins Lymphoma. 2. To apply a less costly, less morbid, well accepted method of treatment on NHL. 3.To find a simple method to increase the immunity. 4.To try a drug which is easy to prepare? Method: Purposive sampling technique was used for the study. Sample of 30 patients age range 25 75 years with histologicaly proven NonHodgkins lymphoma, attending the M.O.I.O.P of the regional cancer centre during a period of 18 months. Groups1) Low grade NonHodgkins Lymphoma 2) Resistant intermediate &High grade NonHodgkins lymphoma (failed chemotherapy) were taken. Procedure : 2 groups were given Triphaladhi Rasayana (15 grams of powder with ghee and honey) twice dailymorning& at bed time with milk as anupana for period of 1month along with selected yoga asanas and niyama? Result: Symptoms included were fever, night sweats, weight loss, lymph nodes enlargement, splenomegaly, and hepatomegaly. In low grade symptom relief was noted in almost all cases. Lymph node changes notedLow grade5 2% (complete remission), 38% (partial remission), 10% (no change), intermediate35% (CR), 52% (PR) & 13% (NC), High grade67% (CR), 33%(PR). Hepatomegaly changes :ve in low grade92.86%, intermediate 90.9% & high grade100%. Splenomegaly changes :ve in low grade92.86%, intermediate72.72% & high grade80% Over all remission status of 30 patientscomplete remission30%, partial remission 30% & no change30%? Conclusion: Thriphaladirasayana along with Yoga therapy is very effective in Low grade NonHodgkins lymphoma and resistant intermediate and high grade Non hodgkins Lymphoma?

Multivoxel magnetic resonance spectroscopy identifies enriched foci of cancer stem-like cells in high-grade gliomas

Directory of Open Access Journals (Sweden)

He T

2017-01-01

Full Text Available Tao He,1–3,* Tianming Qiu,4,* Xiaodong Wang,5 Hongxing Gui,6 Xilong Wang,2 Qikuan Hu,3,7 Hechun Xia,2 Gaoyang Qi,1,2 Jinsong Wu,4 Hui Ma2 1Clinical Medicine College, Ningxia Medical University, 2Department of Neurosurgery, General Hospital of Ningxia Medical University, 3Ningxia Key Laboratory of Cerebrocranial Diseases, The National Key Laboratory Incubation Base, Yinchuan, 4Department of Neurosurgery, Huashan Hospital, Shanghai Medical College, Fudan University, Shanghai, 5Department of Radiology, General Hospital of Ningxia Medical University, Yinchuan, People’s Republic of China; 6Department of Neuroscience and Cell Biology, Robert Wood Johnson Medical School of Rutgers University, Piscataway, NJ, USA; 7Department of Physiology, Ningxia Medical University, Yinchuan, People’s Republic of China *These authors contributed equally to this work Objective: This study investigated the correlation between choline/creatine (Cho/Cr ratios determined by multivoxel proton magnetic resonance spectroscopy (1H-MRS and the distribution of cancer stem-like cells (CSLCs in high-grade gliomas. Patients and methods: Sixteen patients with high-grade gliomas were recruited and underwent 1H-MRS examination before surgery to identify distinct tumor regions with variable Cho/Cr ratios. Using intraoperative neuronavigation, tumor tissues were accurately sampled from regions with high and low Cho/Cr ratios within each tumor. The distribution of CSLCs in samples from glioma tissue regions with different Cho/Cr ratios was quantified by neurosphere culture, immunohistochemistry, and Western blot. Results: The mean neurosphere formation rate in tissues with high Cho/Cr ratios was significantly increased compared with that in low Cho/Cr ratio tissues (13.94±5.94 per 100 cells vs 8.04±3.99 per 100 cells, P<0.001. Immunohistochemistry indicated that tissues with high Cho/Cr ratios had elevated expression of CD133, nestin, and CD15, relative to low Cho/Cr ratio tissue

Standardized Curriculum for Enrichment Agriculture. Grades 7 and 8.

Science.gov (United States)

Mississippi State Dept. of Education, Jackson. Office of Vocational, Technical and Adult Education.

Standardized vocational education course titles and core contents are provided for two courses in Mississippi: agriculture, grades seven and eight. The first course contains the following units: (1) agricultural careers; (2) leadership and Future Farmers of America (FFA); (3) public speaking; (4) parliamentary procedures; (5) introduction to…

Study of 13Cr-4Ni-(Mo (F6NM Steel Grade Heat Treatment for Maximum Hardness Control in Industrial Heats

Directory of Open Access Journals (Sweden)

Massimo De Sanctis

2017-09-01

Full Text Available The standard NACE MR0175 (ISO 15156 requires a maximum hardness value of 23 HRC for 13Cr-4Ni-(Mo steel grade for sour service, requiring a double tempering heat treatment at temperature in the range 648–691 °C for the first tempering and 593–621 °C for the second tempering. Difficulties in limiting alloy hardness after the tempering of forged mechanical components (F6NM are often faced. Variables affecting the thermal behavior of 13Cr-4Ni-(Mo during single and double tempering treatments have been studied by means of transmission electron microscopy (TEM observations, X-ray diffraction measurements, dilatometry, and thermo-mechanical simulations. It has been found that relatively low Ac1 temperatures in this alloy induce the formation of austenite phase above 600 °C during tempering, and that the formed, reverted austenite tends to be unstable upon cooling, thus contributing to the increase of final hardness via transformation to virgin martensite. Therefore, it is necessary to increase the Ac1 temperature as much as possible to allow the tempering of martensite at the temperature range required by NACE without the detrimental formation of virgin martensite upon final cooling. Attempts to do so have been carried out by reducing both carbon (<0.02% C and nitrogen (<100 ppm levels. Results obtained herein show final hardness below NACE limits without an unacceptable loss of mechanical strength.

Improved creep and oxidation behavior of a martensitic 9Cr steel by the controlled addition of boron and nitrogen

Energy Technology Data Exchange (ETDEWEB)

Mayr, Peter [Massachusetts Institute of Technology, Cambridge, MA (United States). Dept. of Materials Science; Graz Univ. of Technology (Austria). Inst. of Material Science and Welding; Holzer, Ivan; Mendez-Martin, Francisca [Graz Univ. of Technology (Austria). Inst. of Material Science and Welding; Albu, Mihaela; Mitsche, Stefan [Graz Univ. of Technology (Austria). Inst. for Electron Microscopy; Gonzalez, Vanessa; Agueero, Alina [Instituto Nacional de Tecnica Aeroespacial, Torrejon de Ardoz (Spain)

2010-07-01

This manuscript gives an overview on recent developments of a martensitic steel grade based on 9Cr3W3CoVNb with controlled additions of boron and nitrogen. Alloy design by thermodynamic equilibrium calculations and calculation of boron-nitrogen solubility is discussed. Out of this alloy design process, two melts of a 9Cr3W3CoVNbBN steel were produced. The investigation focused on microstructural evolution during high temperature exposure, creep properties and oxidation resistance in steam at 650 C. Microstructural characterization of ''as-received'' and creep exposed material was carried out using conventional optical as well as advanced electron microscopic methods. Creep data at 650 was obtained at various stress levels. Longest-running specimens have reached more than 20,000 hours of testing time. In parallel, long-term oxidation resistance has been studied at 650 C in steam atmosphere up to 5,000 hours. Preliminary results of the extensive testing program on a 9Cr3W3CoVNbBN steel show significant improvement in respect to creep strength and oxidation resistance compared to the state-of-the-art 9 wt. % Cr martensitic steel grades. Up to current testing times, the creep strength is significantly beyond the +20% scatterband of standard grade P92 material. Despite the chromium content of 9 wt % the material exhibits excellent oxidation resistance. Steam exposed plain base material shows comparable oxidation behavior to coated material, and the corrosion rate of the boron-nitrogen controlled steel is much lower compared to standard 9 wt % Cr steel grades, P91 and P92. (orig.)

Science Scores in Title I Elementary Schools in North Georgia: A Project Study

Science.gov (United States)

Frias, Ramon

The No Child Left Behind Act (NCLB)'s emphasis of reading, language arts, and mathematics (RLA&M) and its de-emphasis of science has been a source of great concern among educators. Through an objectivist and constructionist framework, this study explored the unforeseen effects of the NCLB on public science education among Title I (TI) and non-Title I (NTI) students. The research questions focused on the effects of NCLB on Criterion Referenced Competency Test (CRCT) scores in the high-stakes subjects of reading, language arts, mathematics and the low stakes subject of science among TI and NTI 3rd, 4th, and 5th grade students in a north Georgia County during the 2010/2011 school year. This study also compared instructional time TI and NTI teachers dedicated to science. A causal-comparative quantitative methodology was used to analyze Georgia's public domain CRCT scores. Three independent-samples t tests showed that TI schools exhibited significantly lower Science CRCT scores than did NTI students at all grade levels (p need students with strong science foundations. Further study is recommended to analyze the factors associated with this science gap between TI and NTI students.

78 FR 66906 - Privacy Act of 1974; System of Records: National Title I Study of Implementation and Outcomes...

Science.gov (United States)

2013-11-07

...) What classroom instructional practices do teachers in Title I schools use to support children's... between prekindergarten and 3rd grade? (4) What school supports and classroom practices are associated... Implementation and Outcomes; Early Childhood Language Development AGENCY: Institute of Education Sciences...

Results of high heat flux testing of W/CuCrZr multilayer composites with percolating microstructure for plasma-facing components

International Nuclear Information System (INIS)

Greuner, Henri; Zivelonghi, Alessandro; Böswirth, Bernd; You, Jeong-Ha

2015-01-01

Highlights: • Improvement of the performance of plasma-facing components made of W and CuCrZr. • Functionally graded composite at the interface of W and CuCrZr to mitigate the CTE. • A three-layer composite system (W volume fraction: 70/50/30%) was developed. • Design of water-cooled divertor components up to 20 MW/m"2 heat load for e.g. DEMO. • HHF tests up to 20 MW/m"2 were successfully performed. - Abstract: Reliable joining of tungsten to copper is a major issue in the design of water-cooled divertor components for future fusion reactors. One of the suggested advanced engineering solutions is to use functionally graded composite interlayers. Recently, the authors have developed a novel processing route for fabricating multi-layer graded W/CuCrZr composites. Previous characterization confirmed that the composite materials possess enhanced strength compared to the matrix alloy and shows reasonable ductility up to 300 °C indicating large potential to extend the operation temperature limit. Furthermore, a three-layer composite system (W volume fraction: 70/50/30%) was developed as a graded interlayer between the W armour and CuCrZr heat sink. In this study, we investigated the structural performance of the graded joint. Three water-cooled mock-ups of a flat tile type component were fabricated using electron beam welding and thermally loaded at the hydrogen neutral beam test facility GLADIS. Cycling tests at 10 MW/m"2 and screening tests up to 20 MW/m"2 were successfully performed and confirmed the expected thermal performance of the compound. The measured temperature values were in good agreement with the prediction of finite element analysis. Microscopic investigation confirmed the structural integrity of the newly developed functionally graded composite after these tests.

Results of high heat flux testing of W/CuCrZr multilayer composites with percolating microstructure for plasma-facing components

Energy Technology Data Exchange (ETDEWEB)

Greuner, Henri, E-mail: henri.greuner@ipp.mpg.de; Zivelonghi, Alessandro; Böswirth, Bernd; You, Jeong-Ha

2015-10-15

Highlights: • Improvement of the performance of plasma-facing components made of W and CuCrZr. • Functionally graded composite at the interface of W and CuCrZr to mitigate the CTE. • A three-layer composite system (W volume fraction: 70/50/30%) was developed. • Design of water-cooled divertor components up to 20 MW/m{sup 2} heat load for e.g. DEMO. • HHF tests up to 20 MW/m{sup 2} were successfully performed. - Abstract: Reliable joining of tungsten to copper is a major issue in the design of water-cooled divertor components for future fusion reactors. One of the suggested advanced engineering solutions is to use functionally graded composite interlayers. Recently, the authors have developed a novel processing route for fabricating multi-layer graded W/CuCrZr composites. Previous characterization confirmed that the composite materials possess enhanced strength compared to the matrix alloy and shows reasonable ductility up to 300 °C indicating large potential to extend the operation temperature limit. Furthermore, a three-layer composite system (W volume fraction: 70/50/30%) was developed as a graded interlayer between the W armour and CuCrZr heat sink. In this study, we investigated the structural performance of the graded joint. Three water-cooled mock-ups of a flat tile type component were fabricated using electron beam welding and thermally loaded at the hydrogen neutral beam test facility GLADIS. Cycling tests at 10 MW/m{sup 2} and screening tests up to 20 MW/m{sup 2} were successfully performed and confirmed the expected thermal performance of the compound. The measured temperature values were in good agreement with the prediction of finite element analysis. Microscopic investigation confirmed the structural integrity of the newly developed functionally graded composite after these tests.

42 CFR 476.86 - Correlation of Title XI functions with Title XVIII functions.

Science.gov (United States)

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Correlation of Title XI functions with Title XVIII functions. 476.86 Section 476.86 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF...) Qio Review Functions § 476.86 Correlation of Title XI functions with Title XVIII functions. (a...

Course Syllabi and Their Effects on Students' Final Grade Performance.

Science.gov (United States)

Serafin, Ana Gil

This study examined the relationship between the changes introduced in a course syllabus for a course titled "Instructional Strategies" and the final grades obtained by freshman and sophomore students in three successive academic periods. A sample of 150 subjects was randomly selected from students enrolled in the course at the…

Cognition Effects of Low-Grade Hypoxia

Science.gov (United States)

2016-07-01

human short-term memory . Br J Anaesth. 1971; 43(6):548–552. 3. Crow TJ, Kelman GR. Psychological effects of mild acute hypoxia. Br J Anaesth. 1973; 45...Journal Article 3. DATES COVERED (From – To) Jan 2003 – Sep 2005 4. TITLE AND SUBTITLE Cognition Effects of Low-Grade Hypoxia 5a. CONTRACT NUMBER... cognitive function are reported in this paper. The study compared cognitive function during short exposures at four different altitudes. Ninety-one

20 CFR 404.535 - How much will we withhold from your title VIII and title XVI benefits to recover a title II...

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false How much will we withhold from your title... Officer § 404.535 How much will we withhold from your title VIII and title XVI benefits to recover a title II overpayment? (a) If past-due benefits are payable to you, we will withhold the lesser of the...

Improving Eighth Grade Students' Reading Comprehension through the Use of the Collision Plus Arts-Integrated Program

Science.gov (United States)

Knight, Taneka L.

2016-01-01

African American and Latino students attending Title I schools in the metropolitan Atlanta area were not reading on grade level. The majority of students are low performing readers and minimally met the reading comprehension requirements. The 2015 average 8th grade reading score for these students was 246 out of 500. This applied dissertation was…

An evaluation procedure of sodium environmental effects on FBR grade SUS316 (316FR) and Modified 9Cr-1Mo steel. On the basis of the studies up to the fiscal year of 1998

International Nuclear Information System (INIS)

1999-01-01

Evaluation of sodium environmental effects on structural materials of fast breeder reactors (FBR's) is one of the key issues for the integrity of the plants. The Elevated Temperature Structural Design Guide for Monju (ETSDG) incorporated an evaluation procedure of sodium environmental effects in the Appendix MA.2, for the conventional steels, such as SUS304, SUS316, SUS321 and 2 1/4Cr-1Mo. Following the establishment of the ETSDG, a new material with superior elevated temperature properties, FBR grade SUS316 (316FR), has been developed, and studies on Mod.9Cr-1Mo steel (Mod.9Cr-1Mo steel) has been performed, for the application to demonstration reactors and successive large-scale reactors. These materials were shown to have, at least equal, or better compatibility with sodium compared with the conventional steels. Moreover, studies have been continued with the conventional steels, particularly with SUS304, for the further validation of the procedure in the ETSDG, especially in terms of long-term properties. Those studies provide basis for the study on 316FR. This report proposed an evaluation procedure of sodium environmental effects on 316FR and Mod.9Cr-1Mo steel, which is to be incorporated into the structural design guide for demonstration fast breeder reactors. The procedure is summarized as follows: (1) Corrosion allowance of 316FR and Mod.9Cr-1Mo can be evaluated by the equation determined in the ETSTG. (2) Strength reduction factors on design allowable values are not necessary for either steel. Strength reduction due to the transfer of carbon and nitrogen, etc does not occur with 316FR, which was the same as SUS304. Mod.9Cr-1Mo steel does not show strength reduction, contrary to 2 l/4Cr-1Mo, similar ferritic steel. (3) Corrosion allowance can be determined separately for thin-walled components. The procedure allows design without correction factors for Mod.9Cr-1Mo steel, which was not possible for 2 1/4Cr-1Mo steel in the ETSDG. (author)

Explosive welding method for manufacturing ITER-grade 316L(N)/CuCrZr hollow structural member

Energy Technology Data Exchange (ETDEWEB)

Ma, Rui, E-mail: mr9980@163.com [PLA University of Science and Technology, Nanjing 210007 (China); Wang, Yaohua [PLA University of Science and Technology, Nanjing 210007 (China); Wu, Jihong [Southwestern Institute of Physics, Chengdu 610041 (China); Duan, Mianjun [PLA University of Science and Technology, Nanjing 210007 (China)

2014-12-15

Highlights: • Develop a new explosive welding method to fabricate the cooling channel of FW. • Utilize effective energy model to accurately calculate optimal welding parameters. • Provide an efficient way for manufacturing high-ductility hollow structural member. - Abstract: In this study, a new explosive welding method provided an effective way for manufacturing ITER-grade 316L(N)/CuCrZr hollow structural member. The welding parameters (stand-off distance and explosion rate) were calculated respectively using equivalent frontal collision wave model and effective energy model. The welded samples were subject to two step heat treatment cycles (solution annealing and aging). Optical microscopy (OM) and scanning electron microscopy (SEM) were utilized to analyze the microstructure of bonding interface. The mechanical properties of the welded samples were evaluated through microhardness test and tensile test. Moreover, the sealing property of the welded specimens was measured through helium leak test. Microstructural analysis showed that the welded sample using effective energy model had an ideal wavy interface. The results of microhardness test revealed an increase in hardness for both sides near to the bonding interface. And the hardening phenomenon of interface region disappeared after the solution annealing. SEM observation indicated that the samples with the post heat treatments exhibited a ductile fracture with dimple features after tensile test. After the specimens undergo aging strengthening, there was an obvious increase in the strength for all specimens. The helium leak test results have proven that the welded specimens are soundness.

T/P23, 24, 911 and 92: New grades for advanced coal-fired power plants-Properties and experience

International Nuclear Information System (INIS)

Vaillant, J.C.; Vandenberghe, B.; Hahn, B.; Heuser, H.; Jochum, C.

2008-01-01

After the development of the well-known T/P91 grade in the early 1980s and the long industrial experiences since the early 1990s, it has been necessary to develop new steels to answer the demand of the powergen industry. New (ultra) super critical boilers require materials with advanced creep properties to reach severe steam parameters. For the 2.25% Cr family, grades 23 and 24 are now available to be used instead of the previous grade 22 with many technical and economical advantages. For the 9% Cr steels, new grades such as T/P911 and T/P92 have been developed with higher creep properties than T/P91. Thanks to its large industrial experience in these new grades, Vallourec and Mannesmann Tubes and Boehler Thyssen Schweisstechnik have now worldwide references of use with these new steel grades. In this paper, information on properties, behaviour and workability will be presented with a focus on ·elevated temperature properties and allowable stresses, ·oxidation and maximum service temperature and ·weldability procedures and recommendations

Secondary Schools Curriculum Guide, Mathematics, Grades 10-12, Levels 87-112.

Science.gov (United States)

Rogers, Arnold R., Ed.; And Others

Behavioral objectives for geometry, algebra, computer mathematics, trigonometry, analytic geometry, calculus, and probability are specified for grades 10 through 12. General objectives are stated for major areas under each topic and are followed by a list of specific objectives for that area. This work was prepared under an ESEA Title III…

Predicting grade of cerebral gliomas using Myo-inositol/Creatine ratio

Directory of Open Access Journals (Sweden)

Lamiaa I.A. Metwally

2014-03-01

Conclusion: MRS has proven to be an important complementary tool saving the patient from unnecessary biopsy taking when it is conclusive thus altering the treatment planning. This study had demonstrated that MI level and MI/Cr ratio are important in presurgical grading of brain tumors.

In the assessment of supratentorial glioma grade: The combined role of multivoxel proton MR spectroscopy and diffusion tensor imaging

Energy Technology Data Exchange (ETDEWEB)

Zou, Q.-G. [Department of Neuroradiology, Union hospital, Tongji Medical College, Huazhong University of Science and Technology, Wuhan (China); Xu, H.-B., E-mail: xuhaibo1120@hotmail.com [Department of Neuroradiology, Union hospital, Tongji Medical College, Huazhong University of Science and Technology, Wuhan (China); Liu, F.; Guo, W. [Department of Neuroradiology, Union hospital, Tongji Medical College, Huazhong University of Science and Technology, Wuhan (China); Kong, X.-C. [Department of Imaging technology, Union hospital, Tongji Medical College, Huazhong University of Science and Technology, Wuhan (China); Wu, Y. [Department of Maternal and Child Health Care, Public Health School, Tongji Medical College, Huazhong University of Science and Technology, Wuhan (China)

2011-10-15

Aim: To detect a difference in the parameters derived from proton magnetic resonance spectroscopy ({sup 1}H-MRS) and diffusion tensor imaging (DTI) between low-grade and high-grade gliomas, and to evaluate whether the combination of these two techniques can improve the diagnostic accuracy of conventional magnetic resonance imaging (MRI) in supratentorial glioma grading. Materials and methods: Thirty patients with histologically proved supratentorial brain gliomas (12 low grade, 18 high grade) were prospectively evaluated with contrast material-enhanced MRI, DTI, and multivoxel {sup 1}H-MRS (135 ms echo time). The tumour grades determined using the three methods were then compared with those obtained at histopathology. Receiver operating characteristic (ROC) analyses were performed to determine the optimum thresholds for glioma grading. Independent sample t-test, Spearman's rank correlation, and the Fisher's exact test were also carried out for statistical analysis. p < 0.05 was considered statistically significant. Results: Statistically significant differences were found between the low-grade and high-grade gliomas for the choline (Cho)/creatine (Cr), N-acetylaspartate (NAA)/Cr, NAA/Cho ratio in the tumours (p < 0.01), apparent diffusion coefficient (ADC) value (p < 0.01), and fractional anisotropy (FA) value (p < 0.05) in the tumours. The NAA/Cr and NAA/Cho ratios and the calculated ADC value significantly correlated with the histological grading of the gliomas (p < 0.01). Using a threshold value of 0.66 for tumour NAA/Cr, 0.265 for NAA/Cho, 1118.1 x 10{sup -6} mm{sup 2}/s for the calculated ADC value, corresponding to the maximum Youden index from the ROC curve of the above-selected parameters, the resultant sensitivities, specificities, positive predictive values (PPVs), negative predictive values (NPVs), and Kappa values were all higher and the fraction of misclassified tumour was lower when compared with conventional MRI. However, only NAA/Cho and

Browse Title Index

African Journals Online (AJOL)

2004): Special Issue 2004, Differential production of immune parameters by mouse strains ... agglutination and complement fixation tests in the field diagnosis ... List All Titles · Free To Read Titles This Journal is Open Access.

Cutting thin sheets of allyl diglycol carbonate (CR-39) with a CW CO2, laser

International Nuclear Information System (INIS)

Kukreja, L.M.; Bhawalkar, D.D.; Basu, C.; Goswami, J.N.

1984-01-01

Recent studies have shown that Allyl Diglycol Carbonate, commercially known as CR-39 (the most sensitive among etch track detectors) can detect relativistic oxygen and other heavier nuclei. We are using large sheets of special grade CR-39 (DOP) in our experiment in Space Shuttle-Spacelab-3. As CR-39 is a highly brittle substance, special care is required to cut CR-39 shetts, especially in case of large sheets and circular cuts. A study of cutting of CR-39 sheets using laser light is described in this paper. It has been found that this method is sufficiently fast to handle large number of sheets and also equally safe for big sheets. A maximum speed up to 200 cm/min with a 5 x 10 4 W/cm 2 laser is obtained during the present study. This study also shows that laser cutting does not affect the track properties of CR-39. (orig.)

Conversion of MX Nitrides to Modified Z-Phase in 9-12%Cr Ferritic Steels

DEFF Research Database (Denmark)

Cipolla, Leonardo

for Z-phase formation was highlighted during the studies. Several 9-12%Cr commercial steels with prolonged high-temperature exposures have been investigated, too. The same mechanism of Z-phase formation observed in 12%Cr model alloys was identified in industrial 9-12%Cr steels after thousands of hours......The 9-12%Cr ferritic steels are extensively used in modern steam power plants at service temperature up to 620°C. Currently the best perform ing ferritic creep resistance steel is the ASTM Grade 92, whose high temperature strength has recently been assessed by European Creep Collaborative Committee...... in 2005 as 600°C/113MPa/10 5h. All previous attempts made in the last twenty years to develop ferritic steels for 650°C applications have failed due to the incapacity to combine the superior oxidation resistance, given by 12%Cr content, with excellent creep resistance of high-alloyed ferritic steels...

INIS: Authority List for Journal Titles

International Nuclear Information System (INIS)

1992-01-01

This is the nineteenth revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). It lists 10,797 journal titles which have contained articles within the scope of INIS. The purpose of this Authority List is to provide descriptive cataloguers with a standard abbreviation for journal titles and to assist users of INIS products with a tool for verifying the full title of a journal. A journal, or periodical, is generally published within a defined, fixed interval between issues, which usually has more than one issue a year, and which usually includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as Annual Review of Nuclear Science are included. Series titles as, for example the McGraw-Hill Series in Nuclear Engineering, are not included in this Authority. Entries: Each entry consists of: - the full journal title (highlighted); - the abbreviated title; - ISSN, if available; - CODEN, if available; - additional information related to the journal title. Arrangement: In Part I, the full journal titles are grouped by country or international organization name and ordered alphabetically, followed by the ISSN, the CODEN in square brackets if available, and then the abbreviated title. The abbreviated title is based on the rules of ISO 4: Documentation - International Code for the Abbreviation of Titles of Periodicals. The abbreviations of the words are taken from the ISDS List of Periodical Title Word Abbreviation. In Part II, the order of the citations is reversed: the abbreviated journal titles are arranged alphabetically, followed by country code. Then the full journal titles are followed by the country of publication, and if available, ISSN and CODEN. Additional Information: There is important information related to the journal titles which are fundamental for tracing the history of the title and the present status. They are listed below and are entered whenever applicable: - Ceased publication; - Superseded by

Title IX Resource Guide

Science.gov (United States)

Office for Civil Rights, US Department of Education, 2015

2015-01-01

Title IX of the Education Amendments of 1972 (Title IX) prohibits discrimination based on sex in education programs and activities in federally funded schools at all levels. If any part of a school district or college receives any Federal funds for any purpose, all of the operations of the district or college are covered by Title IX. The essence…

Getting to one from title 10 + title 32 unity of effort in the homeland

OpenAIRE

Prosch, Caroline Ross.

2011-01-01

CHDS State/Local Approved for public release; distribution is unlimited This thesis bridges the knowledge gap between Title 10 Active Duty and Title 32 National Guard in order to breakdown cultural barriers and reach unity of effort for response operations in the homeland. Regrettably, a unified response was missing among Title 10 Active Duty and Title 32 National Guard members following Hurricane Katrina. Since then, initiatives based in doctrine, statutes and formal recommendations...

Influence of Z-phase on Long-term Creep Stability of Martensitic 9 to 12 % Cr Steels

DEFF Research Database (Denmark)

Danielsen, Hilmar Kjartansson; Hald, John

2009-01-01

Die langfristige Kriechstabilität der neuesten Generation martensitischer 9 bis 12 % kriechfester Stähle basiert auf dem bekannten Grade 91, d. h. auf der Stärkung durch die feinen MNNitride (V und Nb). Langzeit-Hochtemperaturtests zeigen den Ersatz der MN-Nitride durch die thermodynamisch...... stabileren Z-Phasen (Cr(V,Nb)N) mit einem Verlust an Kriechfestigkeit. Cr-Gehalte >10,5 % beschleunigen die Ausscheidung der Z-Phasen. Dies beschränkte Bemühungen, einen martensitischen, kriechfesten Stahl mit hohem Cr-Gehalt zum Schutz vor Oxidation zu entwickeln. 9-%-Cr-Stähle werden offensichtlich nicht...... durch die Z-Phase negativ beeinflusst. Die Untersuchung der Z-Phasen-Ausscheidung hat zur Entwicklung eines 12-%-Cr-martensitischen Versuchsstahls geführt, dessen Kriechfestigkeit durch die Z-Phase gewährleistet wird. Derartige Stähle erlauben die ombination hoher Festigkeit bei gleichzeitig guter...

Magnetocaloric Properties of Fe-Ni-Cr Nanoparticles for Active Cooling

Science.gov (United States)

Chaudhary, V.; Ramanujan, R. V.

2016-10-01

Low cost, earth abundant, rare earth free magnetocaloric nanoparticles have attracted an enormous amount of attention for green, energy efficient, active near room temperature thermal management. Hence, we investigated the magnetocaloric properties of transition metal based (Fe70Ni30)100-xCrx (x = 1, 3, 5, 6 and 7) nanoparticles. The influence of Cr additions on the Curie temperature (TC) was studied. Only 5% of Cr can reduce the TC from ~438 K to 258 K. These alloys exhibit broad entropy v/s temperature curves, which is useful to enhance relative cooling power (RCP). For a field change of 5 T, the RCP for (Fe70Ni30)99Cr1 nanoparticles was found to be 548 J-kg-1. Tunable TCin broad range, good RCP, low cost, high corrosion resistance and earth abundance make these nanoparticles suitable for low-grade waste heat recovery as well as near room temperature active cooling applications.

Browse Title Index

African Journals Online (AJOL)

Items 601 - 650 of 788 ... Browse Title Index ... Issue, Title ... Vol 14, No 1 (2006), Social science research: a critique of quantitative and qualitative methods ... Vol 18, No 1 (2010), Stress among part-time business students: a study in a Ghanaian ...

20 CFR 408.931 - How much will we withhold from your title II and title XVI benefits to recover a title VIII...

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false How much will we withhold from your title II... and Overpayments Adjustment of Title II Benefits § 408.931 How much will we withhold from your title...-due benefits. (b)(1) We will collect the overpayment from current monthly benefits due in a month...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 229 ... Browse Title Index ... Issue, Title. Vol 14, No 2 ... Vol 15, No 1 (2017), Qualitative and quantitative methods of suicide research in old age, Abstract PDF ... Vol 11, No 2 (2013), Simple Algorithm in the Management of Fetal ...

2nd Gen FeCrAl ODS Alloy Development For Accident-Tolerant Fuel Cladding

Energy Technology Data Exchange (ETDEWEB)

Dryepondt, Sebastien N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Massey, Caleb P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Edmondson, Philip D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-08-01

Extensive research at ORNL aims at developing advanced low-Cr high strength FeCrAl alloys for accident tolerant fuel cladding. One task focuses on the fabrication of new low Cr oxide dispersion strengthened (ODS) FeCrAl alloys. The first Fe-12Cr-5Al+Y₂O₃ (+ ZrO₂ or TiO₂) ODS alloys exhibited excellent tensile strength up to 800 C and good oxidation resistance in steam up to 1400 C, but very limited plastic deformation at temperature ranging from room to 800 C. To improve alloy ductility, several fabrication parameters were considered. New Fe-10-12Cr-6Al gas-atomized powders containing 0.15 to 0.5wt% Zr were procured and ball milled for 10h, 20h or 40h with Y2O3. The resulting powder was then extruded at temperature ranging from 900 to 1050 C. Decreasing the ball milling time or increasing the extrusion temperature changed the alloy grain size leading to lower strength but enhanced ductility. Small variations of the Cr, Zr, O and N content did not seem to significantly impact the alloy tensile properties, and, overall, the 2nd gen ODS FeCrAl alloys showed significantly better ductility than the 1st gen alloys. Tube fabrication needed for fuel cladding will require cold or warm working associated with softening heat treatments, work was therefore initiated to assess the effect of these fabrications steps on the alloy microstructure and properties. This report has been submitted as fulfillment of milestone M3FT 16OR020202091 titled, Report on 2nd Gen FeCrAl ODS Alloy Development for the Department of Energy Office of Nuclear Energy, Advanced Fuel Campaign of the Fuel Cycle R&D program.

French investigation of a new V-4Cr-4Ti grade: CEA-J57 - Fabrication and microstructure

Energy Technology Data Exchange (ETDEWEB)

Duquesnes, Vincent; Guilbert, Thomas [CEA Saclay, DEN/DMN/SRMA/LA2M, 91191 Gif Sur Yvette (France); Le Flem, Marion, E-mail: marion.leflem@cea.fr [CEA Saclay, DEN/DMN/SRMA/LA2M, 91191 Gif Sur Yvette (France)

2012-07-15

In the scope of the development of structural materials for application in future fast neutron fission reactors, a V-4Cr-4Ti alloy, which is the reference alloy for the first wall/blanket in lithium fusion reactor, was fabricated. After vacuum arc melting of the starting ingot of 30 kg, 7 mm-thick plates were processed by forging and cold rolling down to 54% thickness reduction with intermediate heat treatment at 1050 Degree-Sign C. The pollution by interstitial impurities such as O, N and C was well controlled and was quite comparable to previous grades by US and Japan - O: 290 mass ppm, C: 70 mass ppm, N: 110 mass ppm. An additional cold-rolling was achieved on a small specimen to get a reduction in thickness of 87%. The recrystallization was investigated through heat treatments between 600 Degree-Sign C and 1200 Degree-Sign C. Hardness measurement on annealed samples suggested the recrystallization to occur around 800 Degree-Sign C for 54% thickness reduction and at a lower temperature for 87% thickness reduction. The minimum hardness was obtained after annealing at 950-1000 Degree-Sign C, the microstructure being fully recrystallized and the hardness isotropic. Above this temperature, hardness increase was significant. Large Ti-rich precipitates (500 nm) formed during forging and oriented along the rolling direction were easily observed but, on the contrary to previous studies, no small Ti-(O,C) precipitates could be detected.

Influence of Z-phase on long-term creep stability of martensitic 9-12% Cr steels

Energy Technology Data Exchange (ETDEWEB)

Danielsen, Hilmar K. [Technical Univ. of Denmark, Lyngby (Denmark). Dept. of Mechanical Engineering; Hald, John [DONG Energy A/S (Denmark); Vattenfall (Denmark)

2010-07-01

The long-term creep strength of the new generation of martensitic creep resistant 9-12%Cr steels since the well-known steel Grade 91 relies strongly on particle strengthening by fine Mn nitrides based on V and Nb. During long-term high-temperature exposures the Mn nitrides may be replaced by the thermodynamically more stable Z-phases (Cr(V,Nb)N) causing a breakdown in creep strength. Cr contents above 10.5% strongly accelerate Z-phase precipitation, which explains the lack of success for all attempts to develop martensitic creep resistant steels with high Cr content for oxidation protection. However 9%Cr steels do not seem to be affected by the Z-phase. Careful control of the Z-phase precipitation process has led to the design of experimental 12%Cr martensitic steels strengthened by fine Z-phase nitrides based on Nb or Ta. Such steels may again enable the combination of high strength and oxidation resistance in the same alloy. This opens a new pathway for further alloy development of the heat resistant martensitic steels. (orig.)

INIS: Authority list for journal titles

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-03-01

This is the twenty-ninth revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). It lists the titles of 12 990 journals which have contained articles within the scope of INIS. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the reader to find titles easily, the list is divided into two parts. In Part I, the full journal titles are grouped by country or international organization responsible for coverage and ordered alphabetically. In Part II, the full journal titles of all countries or international organizations are arranged alphabetically. The country name or the international organization name responsible for coverage of the journal title to INIS is entered in parentheses. Journal titles marked with an asterisk are regularly scanned by INIS. Titles that have been identified by INIS Centres as 'Key Journals' are marked with the hash sign.

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2003-01-01

This is the twenty-ninth revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). It lists the titles of 12 990 journals which have contained articles within the scope of INIS. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the reader to find titles easily, the list is divided into two parts. In Part I, the full journal titles are grouped by country or international organization responsible for coverage and ordered alphabetically. In Part II, the full journal titles of all countries or international organizations are arranged alphabetically. The country name or the international organization name responsible for coverage of the journal title to INIS is entered in parentheses. Journal titles marked with an asterisk are regularly scanned by INIS. Titles that have been identified by INIS Centres as 'Key Journals' are marked with the hash sign

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 488 ... African Journal of Paediatric Surgery. ... Ileocecal valve atresia: Introduction of a new surgical approach ... Vol 4, No 1 (2007), Isolated Bilateral Macrostomia: Case Series and ... Vol 9, No 2 (2012), Laparoscopic inguinal hernia repair in ... List All Titles · Free To Read Titles This Journal is Open Access.

Semisolid forming of S48C steel grade

Science.gov (United States)

Plata, Gorka; Lozares, Jokin; Azpilgain, Zigor; Hurtado, Iñaki; Loizaga, Iñigo; Idoyaga, Zuriñe

2017-10-01

Steel production and component manufacturing industries have to face the challenge of globalization, trying to overcome the economic pressure to remain competitive. Moreover, the lightweighting trend of the latter years implies an even higher challenge to maintain the steel use. Therefore, advanced manufacturing processes will be the cornerstone. In this field, Semisolid forming (SSF) has demonstrated the capability of obtaining complex geometries and saving raw material and energy. Despite it is complicated the SSF of sound components, in Mondragon Unibertsitatea it has been successfully demonstrated the capability of producing strong enough automotive components with 42CrMo4 steel grade. In this work, we demonstrate the capability of SSF S48C steel grade with great mechanical properties.

Liquidus projection of the Nb-Cr-Al system near the Al3(Nb,Cr) + Cr(Al,Nb) eutectic region

International Nuclear Information System (INIS)

Souza, S.A.; Ferrandini, P.L.; Nunes, C.A.; Coelho, A.A.; Caram, R.

2006-01-01

The system Nb-Cr-Al was investigated in the region near the Al 3 (Nb,Cr) + Cr(Al,Nb) eutectic and the liquidus projection of that region was determined based on the microstructural characterization of arc melted alloys. The characterization utilized scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), differential thermal analysis (DTA) and X-ray diffraction (XRD). The results allowed one to determine three primary solidification liquidus surfaces ((Cr,Al) 2 Nb, Cr(Al,Nb) and Al 3 (Nb,Cr)), that are originated from the binary systems Cr-Nb, Cr-Al and Al-Nb. It is proposed the occurrence of the invariant reaction L + (Cr,Al) 2 Nb ↔ Al 3 (Nb,Cr) + Cr(Al,Nb) and of a point of minimum, which involves a three phase reaction, L ↔ Al 3 (Nb,Cr) + Cr(Al,Nb). All alloys studied showed formation of the Al 3 (Nb,Cr) + Cr(Al,Nb) eutectic as the last solidification step with Al(Nb)Cr 2 precipitating from Cr(Al,Nb)

The Effect of Si and Mn on Microstructure and Selected Properties of Cr-Ni Stainless Steels

Directory of Open Access Journals (Sweden)

Kalandyk B.

2017-03-01

Full Text Available Cast stainless steel of the Cr-Ni duplex type is used, among others, for the cast parts of pumps and valves handling various chemically aggressive media. Therefore, the main problem discussed in this article is the problem of abrasion wear resistance in a mixture of SiC and water and resistance to electrochemical corrosion in a 3% NaCl-H2O solution of selected cast steel grades, i.e. typical duplex cast steel, high silicon and manganese duplex cast steel, and Cr-Ni austenitic cast steel (type AISI 316L. The study shows that the best abrasion wear resistance comparable to Ni-Hart cast iron was obtained in the cast duplex steel, where Ni was partially replaced with Mn and N. This cast steel was also characterized by the highest hardness and matrix microhardness among all the tested cast steel grades. The best resistance to electrochemical corrosion in 3% NaCl-H2O solution showed the cast duplex steel with high content of Cr, Mo and N. The addition of Ni plays rather insignificant role in the improvement of corrosion resistance of the materials tested.

Effect of fusion mixture treatment on the surface of low grade natural ruby

Energy Technology Data Exchange (ETDEWEB)

Sakthivel, R., E-mail: velsak_r@yahoo.com; Pradhan, K.C.; Nayak, B.B.; Dash, Tapan; Sahu, R.K.; Mishra, B.K.

2017-05-01

Graphical abstract: The colour of low grade natural ruby is enhanced with fusion mixture treatment. Comparative optical absorption and photoluminesence properties of both untreated and treated ruby samples are studied. - Highlights: • Colour of the low grade natural ruby is improved with fusion mixture treatment. • Surface impurities are removed with fusion mixture. • Photoluminescence spectrum of ruby influenced by its Cr{sup 3+} concentration. • X-ray diffraction study confirms the presence of corundum phases in ruby samples. • Treated ruby looks brighter than untreated ruby due to variation in Cr{sup 3+} concentration. - Abstract: Improvement in aesthetic look of low grade natural ruby (gemstone) surface was clearly evident after fusion mixture treatment. Surface impurities of the gemstone were significantly reduced to give it a face lift. The processing consists of heat treatment (1000 °C) of the raw gemstone with fusion mixture (sodium and potassium carbonates), followed by hydrochloric acid digestion (90 °C) and ultrasonic cleaning.Both the untreated and the treated gemstone were characterized by X-ray diffraction, UV–vis spectroscopy (diffuse reflectance),photoluminescence and X-ray photoelectron spectroscopy. The paper consolidates the results of these studies and presents the effect of the typical chemical treatment (stated above) on the low grade natural ruby. While X-ray diffraction study identifies the occurrence of alumina phase in both the treated and the untreated gemstones, the UV–vis spectra exhibit strong characteristic absorption of Cr{sup 3+}at 400 and 550 nm wavelength for the treated gemstone in contrast to weak absorption observed for the untreated gemstone at such wavelengths, thus showing the beneficial effect of fusion mixture treatment. Peaks observed for the gemstone (for both treated and untreated samples) in the excitation spectra of photoluminescence show a good correlation with observed UV–vis (diffuse reflectance

Black Holes—Deshielo Crónica

Directory of Open Access Journals (Sweden)

Susana Chávez-Silverman

2017-05-01

Full Text Available Abstract Susana Chávez-Silverman is a Califas-born U.S. Latina writer and flaneuse who (against all odds is also an educator, although she mostly laments what’s happened to la cacademia over the last decade or so. She still finds joy and hope in being la High Priestess of SLOW to her students and former students, some of which are among her closest compinches. Of the two crónicas included in this special curated issue of cultural works in PORTAL under the theme Transitions and Dislocations, she says:   ‘My writing/life took a major detour in 2016. For most of the year, I wrote nothing at all. Or rather, nothing except e-mail after email: to administrators, colleagues all over the world, attorneys, friends and relatives. I had scheduled my sabbatical in order to finish a book project, but had been derailed by a Title IX investigation and plagiarism case at my home institution, and the accompanying anxiety and anger . I returned to my book over the summer, culling and editing hundreds of pages of primary texts (letters and emails. But this book is much longer—and truer—than anything I’ve written before and takes a different kind of writing energy, uninterrupted time, and commitment. Writing from a place of anger and anxiety doesn’t serve this book. The two crónicas included in this special curated issue are not part of my book in progress, Our Ubuntu, Montenegro: del Balboa Café al Apartheid and Back. Rather, they were my way of easing back into my (heart space. ‘Casi Víspera’ proves I did write something in 2016 after all (other than email, I mean—I had no memory of it until early this year! ‘Black Holes’ talks about precisely this (remembering and not. I was determined not to let 2016’s plagiarism/Title IX toxic double helix continue to poison me. I wanted to begin 2017 with a bang, and wrote this for my son, for his 30th birthday.’

Cr(III) reactivity and foot dermatitis in Cr(VI) positive patients

DEFF Research Database (Denmark)

Hansen, Malene Barré; Menné, Torkil; Johansen, Jeanne Duus

2006-01-01

Chromium allergy has become synonymous with Cr(VI) allergy. However, real exposure to chromium from leather products may include both Cr(III) and Cr(VI). In this study, we investigate the reactivity to both Cr(VI) and Cr(III) in consecutive patients to analyse the relation between foot eczema/leather...... to Cr(III). The increased risk was not due to a higher degree of sensitivity to Cr(VI). Leather was reported most frequently as the suspected cause of chromium dermatitis (54%). However, Cr(VI) allergics having foot eczema and positive or doubtful Cr(III) reactions often had positive reactions to other...

Application of double-spike isotope dilution for the accurate determination of Cr(III), Cr(VI) and total Cr in yeast.

Science.gov (United States)

Yang, Lu; Ciceri, Elena; Mester, Zoltán; Sturgeon, Ralph E

2006-11-01

A method is presented for the simultaneous determination of Cr(III) and Cr(VI) in yeast using species-specific double-spike isotope dilution (SSDSID) with anion-exchange liquid chromatography (LC) separation and sector field inductively coupled plasma mass spectrometric (SF-ICP-MS) detection. Total Cr is quantitated using ID SF-ICP-MS. Samples were digested on a hot plate at 95+/-2 degrees C for 6 h in an alkaline solution of 0.5 M NaOH and 0.28 M Na2CO3 for the determination of Cr(III) and Cr(VI), whereas microwave-assisted decomposition with HNO3 and H2O2 was used for the determination of total Cr. Concentrations of 2,014+/-16, 1,952+/-103 and 76+/-48 mg kg-1 (one standard deviation, n=4, 3, 3), respectively were obtained for total Cr, Cr(III) and Cr(VI) in the yeast sample. Significant oxidation of Cr(III) to Cr(VI) (24.2+/-7.6% Cr(III) oxidized, n=3) and reduction of Cr(VI) to Cr(III) (37.6+/-6.5% Cr(VI) reduced, n=3) occurred during alkaline extraction and subsequent chromatographic separation at pH 7. Despite this significant bidirectional redox transformation, quantitative recoveries for both Cr(III) and Cr(VI) were achieved using the SSDSID method. In addition, mass balance between total Cr and the sum of Cr(III) and Cr(VI) concentrations was achieved. Method detection limits of 0.3, 2 and 30 mg kg-1 were obtained for total Cr, Cr(VI) and Cr(III), respectively, based on a 0.2-g sub-sample.

Influence of Z-phase on long-term creep stability of martensitic 9-12%Cr steels

Energy Technology Data Exchange (ETDEWEB)

Hald, J. [DONG Energy (Denmark)]|[Vattenfall Europe AG, Berlin (Germany)]|[DTU Mechanical Engineering (Denmark); Danielsen, H.K. [DTU Mechanical Engineering (Denmark)

2008-07-01

The long-term creep strength of the new generation of martensitic creep resistant 9- 12% Cr steels since the well-known steel Grade 91 relies strongly on particle strengthening by fine MN nitrides based on V and Nb. During long-term hightemperature exposures the MN nitrides may be replaced by the thermodynamically more stable Z-phases (Cr(V,Nb)N) causing a breakdown in creep strength. Cr contents above 10.5% strongly accelerate Z-phase precipitation, which explains the lack of success for all attempts to develop martensitic creep resistant steels with high Cr content for oxidation protection. The Z-phase nucleation process by Cr-diffusion into pre-existing MN nitrides is rate controlling for the Z-phase transformation. More work is needed before effects of chemical composition on the nucleation process can be reliably modeled. Careful control of the Z-phase precipitation process has led to the design of experimental 12%Cr martensitic steels strengthened by Z-phase. Such steels may again enable the combination of high strength and oxidation resistance in the same alloy. This opens a new pathway for further alloy development of the heat resistant martensitic steels. (orig.)

Correlation between grade of pearlite spheroidization and laser induced spectra

Science.gov (United States)

Yao, Shunchun; Dong, Meirong; Lu, Jidong; Li, Jun; Dong, Xuan

2013-12-01

Laser induced breakdown spectroscopy (LIBS) which is used traditionally as a spectrochemical analytical technique was employed to analyze the grade of pearlite spheroidization. Three 12Cr1MoV steel specimens with different grades of pearlite spheroidization were ablated to produce plasma by pulse laser at 266 nm. In order to determine the optimal temporal condition and plasma parameters for correlating the grade of pearlite spheroidization and laser induced spectra, a set of spectra at different delays were analyzed by the principal component analysis method. Then, the relationship between plasma temperature, intensity ratios of ionic to atomic lines and grade of pearlite spheroidization was studied. The analysis results show that the laser induced spectra of different grades of pearlite spheroidization can be readily identifiable by principal component analysis in the range of 271.941-289.672 nm with 1000 ns delay time. It is also found that a good agreement exists between the Fe ionic to atomic line ratios and the tensile strength, whereas there is no obvious difference in the plasma temperature. Therefore, LIBS may be applied not only as a spectrochemical analytical technique but also as a new way to estimate the grade of pearlite spheroidization.

Evaluation of 2 1/4 Cr-1 Mo steel for liquid lithium containment. II. Effects of post-weld heat treatment and niobium content. Annual report, 1979

Energy Technology Data Exchange (ETDEWEB)

Anderson, T.L.; Edwards, G.R.

1979-01-01

The lithium corrosion resistance of the regular grade of 2 1/4 Cr-1 Mo steel can be vastly improved with a proper postweld heat treatment, but even greater improvements are needed. Results indicate that if weldments were tempered sufficiently long at 760C to remove all Mo/sub 2/C from the microstructure, even greater resistance to attack by low nitrogen lithium could be achieved. Corrosion tests should eventually be performed on regular grade 2 1/4 Cr-1 Mo steel weldments which have been given a long-term (> 25 h) post-weld temper at 760C. Lithium corrosion resistance of regular grade 2 1/4 Cr-1 Mo steel may also be improved by employing a quench and temper heat treatment. Quenched microstructures have more homogenous distribution of carbides than isothermally annealed microstructures, and if properly tempered, should provide excellent lithium corrosion resistance. Furthermore, the toughness of such a lower bainite microstructure should be better than that of the ferrite-bainitic microstructure created by an isothermal anneal. Numerous parameters, all potentially deleterious to the lithium corrosion resistance of 2 1/4 Cr-1 Mo steel, remain to be investigated; two such variables are velocity effects and lead content in the lithium.

Evaluation of 2 1/4 Cr-1 Mo steel for liquid lithium containment. II. Effects of post-weld heat treatment and niobium content. Annual report, 1979

International Nuclear Information System (INIS)

Anderson, T.L.; Edwards, G.R.

1979-01-01

The lithium corrosion resistance of the regular grade of 2 1/4 Cr-1 Mo steel can be vastly improved with a proper postweld heat treatment, but even greater improvements are needed. Results indicate that if weldments were tempered sufficiently long at 760C to remove all Mo 2 C from the microstructure, even greater resistance to attack by low nitrogen lithium could be achieved. Corrosion tests should eventually be performed on regular grade 2 1/4 Cr-1 Mo steel weldments which have been given a long-term (> 25 h) post-weld temper at 760C. Lithium corrosion resistance of regular grade 2 1/4 Cr-1 Mo steel may also be improved by employing a quench and temper heat treatment. Quenched microstructures have more homogenous distribution of carbides than isothermally annealed microstructures, and if properly tempered, should provide excellent lithium corrosion resistance. Furthermore, the toughness of such a lower bainite microstructure should be better than that of the ferrite-bainitic microstructure created by an isothermal anneal. Numerous parameters, all potentially deleterious to the lithium corrosion resistance of 2 1/4 Cr-1 Mo steel, remain to be investigated; two such variables are velocity effects and lead content in the lithium

Correlation between bulk- and surface chemistry of Cr-tanned leather and the release of Cr(III) and Cr(VI)

Energy Technology Data Exchange (ETDEWEB)

Hedberg, Yolanda S., E-mail: yolanda@kth.se [KTH Royal Institute of Technology, School of Chemical Science and Engineering, Department of Chemistry, Division of Surface and Corrosion Science, SE-10044 Stockholm (Sweden); Institute of Environmental Medicine, Karolinska Institutet, Box 210, SE-17177 Stockholm (Sweden); Lidén, Carola, E-mail: carola.liden@ki.se [Institute of Environmental Medicine, Karolinska Institutet, Box 210, SE-17177 Stockholm (Sweden); Odnevall Wallinder, Inger, E-mail: ingero@kth.se [KTH Royal Institute of Technology, School of Chemical Science and Engineering, Department of Chemistry, Division of Surface and Corrosion Science, SE-10044 Stockholm (Sweden)

2014-09-15

Graphical abstract: - Highlights: • Released reducing/complexing leather-specific species can reduce released Cr(VI). • No co-released species enable the formation of Cr(VI) in solution. • The major Cr species released from leather in phosphate buffer was Cr(III) (>82%). • No Cr(VI) was released into artificial sweat. - Abstract: About 1–3% of the adult general population in Europe is allergic to chromium (Cr). The assessment of the potential release of Cr(III) and Cr(VI) from leather is hence important from a human health and environmental risk perspective. The Cr(VI) content in leather was recently restricted in the European Union. The aim of this study was to assess possible correlations between the bulk and surface chemistry of leather, released Cr(III) and Cr(VI), and capacities of co-released leather specific species to reduce and complex released Cr. Four differently tanned leathers were characterized by scanning electron microscopy with energy dispersive spectroscopy, X-ray photoelectron spectroscopy, attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, and the diphenylcarbazide colorimetric method. Their characteristics were compared with results on Cr(III) and Cr(VI) release into artificial sweat (ASW, pH < 6.5) and phosphate buffer (PB, pH 7.5–8.0), measured by means of spectrophotometry and atomic absorption spectroscopy. Co-released leather-specific species were shown to reduce Cr(VI), both in ASW and in PB. Their reduction capacities correlated with findings of the surface content of Cr and of released Cr. Leather samples without this capacity, and with less aromatic surface groups visible by ATR-FTIR, revealed Cr(VI) both at the surface and in solution (PB)

32 CFR 644.62 - Title evidence.

Science.gov (United States)

2010-07-01

... HANDBOOK Acquisition Procurement of Title Evidence, Title Clearance, and Closings § 644.62 Title evidence... and their charter to issue the same. They must also be financially sound and be willing and able to...

Title to mining properties

International Nuclear Information System (INIS)

Crouch, K.M.

1976-01-01

The requirements of the law which must be met in order to create title to an unpatented mining claim and the procedures which should be followed when an attempt is made to determine the title to the claim is acceptable are reviewed

Impact Strength of Austenitic and Ferritic-Austenitic Cr-Ni Stainless Cast Steel in -40 and +20°C Temperature

Directory of Open Access Journals (Sweden)

Kalandyk B.

2014-10-01

Full Text Available Studies described in this paper relate to common grades of cast corrosion resistant Cr-Ni steel with different matrix. The test materials were subjected to heat treatment, which consisted in the solution annealing at 1060°C followed by cooling in water. The conducted investigations, besides the microstructural characteristics of selected cast steel grades, included the evaluation of hardness, toughness (at a temperature of -40 and +20oC and type of fracture obtained after breaking the specimens on a Charpy impact testing machine. Based on the results of the measured volume fraction of ferrite, it has been found that the content of this phase in cast austenitic steel is 1.9%, while in the two-phase ferritic-austenitic grades it ranges from 50 to 58%. It has been demonstrated that within the scope of conducted studies, the cast steel of an austenitic structure is characterised by higher impact strength than the two-phase ferritic-austenitic (F-A grade. The changing appearance of the fractures of the specimens reflected the impact strength values obtained in the tested materials. Fractures of the cast austenitic Cr-Ni steel obtained in these studies were of a ductile character, while fractures of the cast ferritic-austenitic grade were mostly of a mixed character with the predominance of brittle phase and well visible cleavage planes.

Superficial characterization and nano structural of nano multilayers Cr/Cr N obtained by UBM with different unbalance grades; Caracterizacion superficial y nano estructural de nano multicapas Cr/CrN obtenidas por UBM con diferentes grados de desbalance

Energy Technology Data Exchange (ETDEWEB)

Piratoba, U. [Universidad Nacional de Colombia, Departamento de Fisica, Carrera 45 No. 26-85, Edificio Uriel Gutierrez, Bogota D. C. (Colombia); Arenas A, J. [UNAM, Instituto de Fisica, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Olaya, J. J., E-mail: ulisesp3@hotmail.com [Universidad Nacional de Colombia, Departamento de Ingenieria Mecanica y Mecatronica, Carrera 30 No. 45-03, Edificio 453, Bogota D. C. (Colombia)

2013-10-01

Coatings of 25 bilayers of Cr/Cr N, with total thickness between 1.32 and 1.67 microns, were deposited by reactive sputtering on silicon and H13 steel, in argon and argon with nitrogen atmospheres. A power of 160 watts, flows of argon and nitrogen of 9 and 3 sc cm respectively, and an axial unbalanced magnetron, whose coefficient of geometrical unbalance K{sub G} was varied between 0.85 and 1.37. Of these coatings, micrographs of surface and cross section scanning electron microscopy were obtained, was make a micro structural characterization with X-ray diffraction, a nano structural characterization by transmission electron microscopy, and surface characterization by atomic force microscopy in tapping mode: analysis showed uniform surface coating with globular and pyramidal formations, which contain some granular inclusions and microscopic craters. With the increase in the unbalance of the magnetic field, the grain size, the roughness and the speed of the coatings growth were increased. (Author)

Correlation between bulk- and surface chemistry of Cr-tanned leather and the release of Cr(III) and Cr(VI).

Science.gov (United States)

Hedberg, Yolanda S; Lidén, Carola; Odnevall Wallinder, Inger

2014-09-15

About 1-3% of the adult general population in Europe is allergic to chromium (Cr). The assessment of the potential release of Cr(III) and Cr(VI) from leather is hence important from a human health and environmental risk perspective. The Cr(VI) content in leather was recently restricted in the European Union. The aim of this study was to assess possible correlations between the bulk and surface chemistry of leather, released Cr(III) and Cr(VI), and capacities of co-released leather specific species to reduce and complex released Cr. Four differently tanned leathers were characterized by scanning electron microscopy with energy dispersive spectroscopy, X-ray photoelectron spectroscopy, attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, and the diphenylcarbazide colorimetric method. Their characteristics were compared with results on Cr(III) and Cr(VI) release into artificial sweat (ASW, pHleather-specific species were shown to reduce Cr(VI), both in ASW and in PB. Their reduction capacities correlated with findings of the surface content of Cr and of released Cr. Leather samples without this capacity, and with less aromatic surface groups visible by ATR-FTIR, revealed Cr(VI) both at the surface and in solution (PB). Copyright © 2014 The Authors. Published by Elsevier B.V. All rights reserved.

High temperature oxidation of 9% and 12% Cr steel: effect of water vapour; Oxidation haute temperature d'un acier 9% et 12% de teneur Cr. Effet de la vapeur d'eau

Energy Technology Data Exchange (ETDEWEB)

Evin, H.; Heritier, D.; Chevalier, S. [Universite de Bourgogne, Institut Carnot de Bourgogne UMR 5209 CNRS, 21 - Dijon (France); Fojer, C. [OCAS N.V. ArcelorMittal Research Industry Gent, Zelzate (Belgium)

2008-07-01

Isothermal tests were performed on commercial 9%Cr and 12%Cr steels between 600 and 750 deg C in air under atmospheric pressure. The same steels were also tested in oxidizing atmosphere enriched with 12% H{sub 2}O at 700 deg C for 24 hours. Kinetics data were registered and the corrosion products were analyzed using different characterization tools such as scanning electron microscope, x-ray diffraction and secondary ions mass spectrometry. 9%Cr steels showed very limited high temperature corrosion behavior in air, because a breakaway appeared after less than 80 hours at 750 deg C. Spinel oxides composed of iron, chromium and manganese (Mn{sub 1.5}Cr{sub 1.5}O{sub 4} and MnFe{sub 2}O{sub 4}) were identified over the surfaces of both steel grades after oxidation. (Cr,Fe){sub 2}O{sub 3} was also identified especially at 700 deg C and 750 deg C, whereas Fe{sub 2}O{sub 3} mainly grew at 600 and 650 deg C. Differences in oxide morphology and composition were noticed between the samples oxidized under air and air + 12 % water vapor. (authors)

Elaboration of functionally graded materials for plasma facing components of the thermonuclear machines

International Nuclear Information System (INIS)

Autissier, Emmanuel

2014-01-01

The objective of this study was to develop a Functionally Graded Material (FGM) W/Cu to replace the compliance layer (Cu-OFHC) in the plasma facing components of thermonuclear fusion reactor like ITER. The peculiarity of this work is to elaborate these materials without exceeding the melting temperature of copper in order to control its microstructure. The co-sintering is the most attractive solution to achieve this goal. The first phase of this study has been to decrease the sintering temperature of the tungsten to achieve this co-sintering. The elaboration of a Functionally Graded Materials being delicate, thermomechanical calculations were performed in order to determine the number and chemical composition in order to increase the lifespan of Plasma Facing Components. Spark Plasma Sintering conditions were optimized in order to achieve maximum density of W x Cu 1-x composites. The effect of copper content and density of the W x Cu 1-x composites on thermal and mechanical properties was investigated. The SPS conditions were applied for W/CuCrZr assemblies with a compliance layer composed of several interlayers. The importance of time for the integrity of assemblies thereof has been highlighted. The study of the dwell time during W/CuCrZr assembly leads to identify a parameter to characterize the integrity of the interface regardless of the composition and the nature of the layer of compliance. Moreover, the phenomena associated with the formation of the interface assembly have been identified. The interface W/W x Cu 1-x is formed by the extrusion of the copper layer of the W x Cu 1-x inside the tungsten porosities. The W y Cu 1-y /CuCrZr interface is formed by copper migration of CuCrZr layer inside the W y Cu 1-y layer. Finally optimization assembly conditions showed that the mechanical stresses due to the densification of the Functionally Graded Materials can be limited by sintering the FGM before the assembly. (author)

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2005-01-01

This is the 31st revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13,104 journal titles, 2,078 regularly scanned journals and 561 key journals. It was last updated in February 2005. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part III, all journals that are regularly scanned by INIS Centers are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part IV, all journals that are regularly scanned by INIS Centers are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part V, all journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part VI, all journals are sorted alphabetically under their title. The name of the

INIS: Authority list for journal titles

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-03-01

This is the 31st revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13,104 journal titles, 2,078 regularly scanned journals and 561 key journals. It was last updated in February 2005. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part III, all journals that are regularly scanned by INIS Centers are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part IV, all journals that are regularly scanned by INIS Centers are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part V, all journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part VI, all journals are sorted alphabetically under their title. The name of the

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2006-01-01

This is the 32nd revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13,231 journal titles, 2,125 regularly scanned journals and 555 key journals. It was last updated in February 2006. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part III, all journals that are regularly scanned by INIS Centres are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part IV, all journals that are regularly scanned by INIS Centres are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part V, all journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part VI, all journals are sorted alphabetically under their title. The name of the

Characteristics of Modified 9Cr-1Mo Steel for Reactor Pressure Vessel of Very High Temperature Gas Cooled Reactor

Energy Technology Data Exchange (ETDEWEB)

Kim, Sung Ho; Ryu, W. S.; Han, Chang Hee; Yoon, J. H.; Chang, Jong Hwa

2004-11-15

Many researches and developments have been progressed for the construction of VHTR by 2020 in Korea. Modified 9Cr-1Mo steel has been receiving attention for the application to the reactor pressure vessel material of VHTR. We collected and analyzed the research data for modified 9Cr-1Mo steel in order to understand the characteristics of modified 9Cr-1Mo steel. The modified 9Cr-1Mo steel is a modified alloy system similar to conventional 9Cr-1Mo grade ferritic steel. Modifications include additions of vanadium, niobium, and nitrogen, as well as lower carbon content. In this report, we summarized the change of microstructure and mechanical properties after tempering, thermal aging, and irradiation. Modified 9Cr-1Mo steel has high strength and thermal conductivity, low thermal expansion, and good resistance to corrosion. But the irradiation embrittlement behavior of modified 9Cr-1Mo steel should be evaluated and the evaluation methodology also should be developed. At the same time, the characteristics of weldment which is the weak part in pressure vessel should be evaluated.

Effect of Cr content on the SHS reaction of Cr-Ti-C system

International Nuclear Information System (INIS)

Zhang, W.N.; Wang, H.Y.; Wang, P.J.; Zhang, J.; He, L.; Jiang, Q.C.

2008-01-01

The effect of Cr content on the self-propagating high temperature synthesis (SHS) reaction of Cr-Ti-C system has been investigated in this research. The thermodynamics calculation indicates that the TiC possesses higher thermodynamic stability than the Cr 23 C 6 , Cr 7 C 3 and Cr 3 C 2 phases, and the formation of TiC is the most exothermic. Additionally, the adiabatic combustion temperature (T ad ) decreases with the increase of Cr content except for the phase transition regions. The XRD result shows that the type of products synthesized by SHS changes that a higher Cr content corresponds to higher chromium carbide. When Cr content is 10 wt.%, only solid solution (Ti,Cr)C ss is formed in the products. When Cr content increases to 20 wt.%, besides (Ti,Cr)C ss , the Cr 7 C 3 phase is also detected. With the Cr content further increasing to 30 and 40 wt.%, the products consist of (Ti,Cr)C ss , Cr 23 C 6 , Cr 7 C 3 and Cr, and therefore, much higher chromium carbide is synthesized. When Cr content reaches 50 wt.%, however, the Cr 7 C 3 disappears and the final products become (Ti,Cr)C ss , Cr 23 C 6 and Cr. Moreover, when Cr content increases from 10 to 20 wt.%, the lattice parameter of (Ti,Cr)C ss decreases, while it increases when the Cr content ranges from 20 to 50 wt.%. Furthermore, the microstructure shows that the TiC particulate size decreases from ∼8 to ∼2 μm with the increase of Cr content from 10 to 50 wt.%, and the morphology shape of TiC particulate becomes more and more spherical

First Annual Progress Report on Radiation Tolerance of Controlled Fusion Welds in High Temperature Oxidation Resistant FeCrAl Alloys

Energy Technology Data Exchange (ETDEWEB)

Field, Kevin G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gussev, Maxim N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hu, Xunxiang [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yamamoto, Yukinori [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Howard, Richard H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-12-01

The present report summarizes and discusses the first year efforts towards developing a modern, nuclear grade FeCrAl alloy designed to have enhanced radiation tolerance and weldability under the Department of Energy (DOE) Nuclear Energy Enabling Technologies (NEET) program. Significant efforts have been made within the first year of this project including the fabrication of seven candidate FeCrAl alloys with well controlled chemistry and microstructure, the microstructural characterization of these alloys using standardized and advanced techniques, mechanical properties testing and evaluation of base alloys, the completion of welding trials and production of weldments for subsequent testing, the design of novel tensile specimen geometry to increase the number of samples that can be irradiated in a single capsule and also shorten the time of their assessment after irradiation, the development of testing procedures for controlled hydrogen ingress studies, and a detailed mechanical and microstructural assessment of weldments prior to irradiation or hydrogen charging. These efforts and research results have shown promise for the FeCrAl alloy class as a new nuclear grade alloy class.

7 CFR 1927.55 - Title clearance services.

Science.gov (United States)

2010-01-01

... REGULATIONS TITLE CLEARANCE AND LOAN CLOSING Real Estate Title Clearance and Loan Closing § 1927.55 Title clearance services. (a) Responsibilities of closing agents. Services to be provided to the agency and the borrower by a closing agent in connection with the transaction vary depending on whether a title insurance...

Preliminary Microstructural and Microscratch Results of Ni-Cr-Fe and Cr3C2-NiCr Coatings on Magnesium Substrate

Science.gov (United States)

Istrate, B.; Munteanu, C.; Lupescu, S.; Benchea, M.; Vizureanu, P.

2017-06-01

Thermal coatings have a large scale application in aerospace and automotive field, as barriers improving wear mechanical characteristics and corrosion resistance. In present research, there have been used two types of coatings, Ni-Cr-Fe, respectively Cr3C2-NiCr which were deposited on magnesium based alloys (pure magnesium and Mg-30Y master alloy). There have been investigated the microstructural aspects through scanning electronic microscopy and XRD analysis and also a series of mechanical characteristics through microscratch and indentation determinations. The results revealed the formation of some adherent layers resistant to the penetration of the metallic indenter, the coatings did not suffer major damages. Microstructural analysis highlighted the formation of Cr3C2, Cr7C3, Cr3Ni2, Cr7Ni3, FeNi3, Cr-Ni phases. Also, the apparent coefficient of friction for Ni-Cr-Fe coatings presents superior values than Cr3C2-NiCr coatings.

Correlation between aging grade of T91 steel and spectral characteristics of the laser-induced plasma

Energy Technology Data Exchange (ETDEWEB)

Li, Jun [Power Electric College in South China University of Technology, Guangzhou 510640 (China); Lu, Jidong, E-mail: jdlu@scut.edu.cn [Power Electric College in South China University of Technology, Guangzhou 510640 (China); Dai, Yuan [Electric Power Research Institute of Guangdong Power Grid Company, Guangzhou 510080 (China); Dong, Meirong [Power Electric College in South China University of Technology, Guangzhou 510640 (China); Zhong, Wanli [Electric Power Research Institute of Guangdong Power Grid Company, Guangzhou 510080 (China); Yao, Shunchun [Power Electric College in South China University of Technology, Guangzhou 510640 (China)

2015-08-15

Highlights: • Laser-induced breakdown spectroscopy (LIBS) was first employed to estimate the aging grade of T91 steel. • The differences from the ionic-to-atomic ratio of the same elements indicated that the grade is the reason to cause the difference of the plasma characteristics. • Good unique value correlations between the peak intensity ratio of CrI/FeI, MoI/FeI and the aging grade were found. • The research indicates that LIBS technique is a potential way to estimate the aging grade of T91 steel. - Abstract: T91 steel with favorable mechanical performance has become the representative heat-resistant steel used as heat exchange surfaces in supercritical and ultra-supercritical boilers. The organizational structure and mechanical properties change during the service period, called material aging, which affects the service life and the equipment safety. To develop a fast and easy aging predictive technique of heat exchange metal surfaces, laser-induced breakdown spectroscopy (LIBS) was applied to investigate the plasma characteristics of T91 steel specimens with different aging grades. The metallographic structure, mechanical properties and spectral characteristics of the specimens were analyzed. Then, the correlations between the spectral characteristics and the aging grade were established. The analysis results show that the martensite substructure disappears, and the dimension of the carbide particles among the crystal lattices increases with aging. At the same time, the hardness of the samples gradually decreases. The peak intensities of both the matrix and the alloying element increases then decreases with aging, owing to the change of the metallography structure and mechanical properties. Furthermore, good unique value correlations between the intensity ratio of CrI/FeI, MoI/FeI and the aging grade are found. This demonstrates that LIBS is a possible new way to estimate the aging grade of metal materials.

Correlation between aging grade of T91 steel and spectral characteristics of the laser-induced plasma

International Nuclear Information System (INIS)

Li, Jun; Lu, Jidong; Dai, Yuan; Dong, Meirong; Zhong, Wanli; Yao, Shunchun

2015-01-01

Highlights: • Laser-induced breakdown spectroscopy (LIBS) was first employed to estimate the aging grade of T91 steel. • The differences from the ionic-to-atomic ratio of the same elements indicated that the grade is the reason to cause the difference of the plasma characteristics. • Good unique value correlations between the peak intensity ratio of CrI/FeI, MoI/FeI and the aging grade were found. • The research indicates that LIBS technique is a potential way to estimate the aging grade of T91 steel. - Abstract: T91 steel with favorable mechanical performance has become the representative heat-resistant steel used as heat exchange surfaces in supercritical and ultra-supercritical boilers. The organizational structure and mechanical properties change during the service period, called material aging, which affects the service life and the equipment safety. To develop a fast and easy aging predictive technique of heat exchange metal surfaces, laser-induced breakdown spectroscopy (LIBS) was applied to investigate the plasma characteristics of T91 steel specimens with different aging grades. The metallographic structure, mechanical properties and spectral characteristics of the specimens were analyzed. Then, the correlations between the spectral characteristics and the aging grade were established. The analysis results show that the martensite substructure disappears, and the dimension of the carbide particles among the crystal lattices increases with aging. At the same time, the hardness of the samples gradually decreases. The peak intensities of both the matrix and the alloying element increases then decreases with aging, owing to the change of the metallography structure and mechanical properties. Furthermore, good unique value correlations between the intensity ratio of CrI/FeI, MoI/FeI and the aging grade are found. This demonstrates that LIBS is a possible new way to estimate the aging grade of metal materials

Correlation between grade of pearlite spheroidization and laser induced spectra

International Nuclear Information System (INIS)

Yao, Shunchun; Dong, Meirong; Lu, Jidong; Li, Jun; Dong, Xuan

2013-01-01

Laser induced breakdown spectroscopy (LIBS) which is used traditionally as a spectrochemical analytical technique was employed to analyze the grade of pearlite spheroidization. Three 12Cr1MoV steel specimens with different grades of pearlite spheroidization were ablated to produce plasma by pulse laser at 266 nm. In order to determine the optimal temporal condition and plasma parameters for correlating the grade of pearlite spheroidization and laser induced spectra, a set of spectra at different delays were analyzed by the principal component analysis method. Then, the relationship between plasma temperature, intensity ratios of ionic to atomic lines and grade of pearlite spheroidization was studied. The analysis results show that the laser induced spectra of different grades of pearlite spheroidization can be readily identifiable by principal component analysis in the range of 271.941–289.672 nm with 1000 ns delay time. It is also found that a good agreement exists between the Fe ionic to atomic line ratios and the tensile strength, whereas there is no obvious difference in the plasma temperature. Therefore, LIBS may be applied not only as a spectrochemical analytical technique but also as a new way to estimate the grade of pearlite spheroidization. (paper)

National Ignition Facility Title II Design Plan

International Nuclear Information System (INIS)

Kumpan, S

1997-01-01

This National Ignition Facility (NIF) Title II Design Plan defines the work to be performed by the NIF Project Team between November 1996, when the U.S. Department of Energy (DOE) reviewed Title I design and authorized the initiation of Title H design and specific long-lead procurements, and September 1998, when Title 11 design will be completed

RIGScan CR: RIGScan CR49.

Science.gov (United States)

2004-01-01

RIGScan CR49, a 125I-labelled CR monoclonal antibody directed against the tumour-associated antigen TAG-72, is undergoing development with Neoprobe for the intraoperative detection of metastatic colorectal cancer. The Neoprobe's proprietary RIGS (radioimmunoguided surgery) technology combines an injectable radiolabelled cancer-targeting agent and hand-held radiation detection probe that emits an audible tone when located tissue has accumulated a significant amount of the radioactive agent. Neoprobe's RIGS technology also includes a patented surgical method providing surgeons with real-time information to locate tumour deposits that can not be detected by other conventional methods. The RIGS technology has been evaluated in late clinical studies for the detection of adenocarcinomas including primary colorectal, gastrointestinal, breast, ovarian, pancreatic, prostate and neuroendocrine/endocrine. Neoprobe signed an option agreement for its first-generation RIGScan compound, RIGScan CR, with OncoSurg Inc. (formerly NuRigs Ltd). The second-generation humanised RIGScan CR agent was also optionally licensed to OncoSurg Inc. In 1997, Neoprobe filed for approval with the US FDA and the EMEA for RIGScan CR for the intraoperative detection of metastatic colorectal cancer. Both regulatory agencies have requested additional clinical data. On 19 April 2004, Neoprobe announced that it had met with the US FDA to discuss its position on submitting additional clinical information in response to the FDA's questions regarding the Biologic Licence Application (BLA) for RIGScan CR49. The company provided the FDA with new information related to a survival differential for patients whose colorectal cancer was evaluated with RIGScan CR49. The information was not available at the time of the BLA's submission in 1997. The agency indicated that it would consider accepting survival data from one of the two phase III trials, NEO2-14, but not from another trial NEO2-13, as supportive data for a

24 CFR 202.12 - Title II.

Science.gov (United States)

2010-04-01

... INSTITUTIONS AND MORTGAGEES Title I and Title II Specific Requirements § 202.12 Title II. (a) Tiered pricing—(1... rate up to two percentage points under the mortgagee's customary lending practices must be based on... after accounting for the value of servicing rights generated by making the loan and other income to the...

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2007-01-01

This is the 33rd revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13 396 journal titles, 2 170 regularly scanned journals and 578 key journals. It was last updated in February 2007. A journal - or periodical - is a continuing publication issued in a succession of discrete parts, usually bearing numbering and/or chronological designations and intended to be continued indefinitely. It is generally published within a defined, fixed interval between issues and normally appears more than once per year. It includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as the Annual Review of Nuclear Science are included, but series titles such as the McGraw-Hill Series in Nuclear Engineering are not. The purpose of this document is to provide descriptive cataloguers with standard elements to include in bibliographic level 'S' of the INIS record. These elements include field (tag) 229 (Full Journal Title), 320 (ISSN) and 321 (CODEN). The full journal title is mandatory, and either the ISSN or the CODEN must be included (both may appear). Instructions on how to use this and other elements of the INIS record format are found in INIS: Guide to Bibliographic Description (IAEA-INIS-1). In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: - In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. - In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. - In Part III, all journals that are regularly scanned by

20 CFR 416.573 - How much will we withhold from your title II and title VIII benefits to recover a title XVI...

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false How much will we withhold from your title II... Payment of Benefits, Overpayments, and Underpayments § 416.573 How much will we withhold from your title...-due benefits. (b)(1) We will collect the overpayment from current monthly benefits due in a month by...

Cr3+ and Cr4+ luminescence in glass ceramic silica

International Nuclear Information System (INIS)

Martines, Marco A.U.; Davolos, Marian R.; Jafelicci, Miguel Junior; Souza, Dione F. de; Nunes, Luiz A.O.

2008-01-01

This paper reports on the effect of glass ceramic silica matrix on [CrO 4 ] 4- and Cr 2 O 3 NIR and visible luminescence. Chromium-containing silica was obtained by precipitation from water-glass and chromium nitrate acid solution with thermal treatment at 1000 deg. C. From XRD results silica and silica-chromium samples are crystalline. The chromium emission spectrum presents two main broad bands: one in the NIR region (1.1-1.7μm) and other in the visible region (0.6-0.7μm) assigned to Cr 4+ and to Cr 3+ , respectively. This thermal treated glass ceramic silica-chromium sample stabilizes the [CrO 4 ] 4- where Cr 4+ substitutes for Si 4+ and also hexacoordinated Cr 3+ group probably as segregated phase in the system. It can be pointed out that luminescence spectroscopy is a powerful tool for detecting the two chromium optical centers in the glass ceramic silica

Study of the experimental parameters for the determination of Ca, Cr, Cu, Fe, Mn and Ni on nuclear grade UO2 by X-ray fluorescence technique

International Nuclear Information System (INIS)

Salvador, V.L.R.

1982-01-01

An analytical method for the simultaneous determinations of low concentrations of Ca, Cr, Cu, Fe, Mn and Ni on the nuclear grade UO 2 by X-ray fluorescence technique, without the use of chemical treatment, is described. The optimization of the experimental conditions was established on the X-ray fluorescence spectrometer and a low limit of detection (4 - 7 μg/gU) was achieved which satisfies the requirement in the nuclear fuel specification. The samples were prepared in the form of double layer pressed pellets using boric acid as a binding agent. The characteristic first order K sub(α) line intensity of each minor component was measured and the values of its concentrations were deduced using respective standard calibrations curves. The precision, accuracy and acceptability of the method were determined for all elements. The values of the precision are in the range of 2 - 10% and the accuracy are lower than 7%. (Author) [pt

Measurements of diagnostic examination performance using quantitative apparent diffusion coefficient and proton MR spectroscopic imaging in the preoperative evaluation of tumor grade in cerebral gliomas

International Nuclear Information System (INIS)

Server, Andres; Kulle, Bettina; Gadmar, Oystein B.; Josefsen, Roger; Kumar, Theresa; Nakstad, Per H.

2011-01-01

Purpose: Tumor grading is very important both in treatment decision and evaluation of prognosis. While tissue samples are obtained as part of most therapeutic approaches, factors that may result in inaccurate grading due to sampling error (namely, heterogeneity in tissue sampling, as well as tumor-grade heterogeneity within the same tumor specimen), have led to a desire to use imaging better to ascertain tumor grade. The purpose in our study was to evaluate the sensitivity, specificity, positive predictive value (PPV), negative predictive value (NPV), area under the curve (AUC), and accuracy of diffusion-weighted MR imaging (DWI), proton MR spectroscopic imaging (MRSI) or both in grading primary cerebral gliomas. Materials and methods: We performed conventional MR imaging (MR), DWI, and MRSI in 74 patients with newly diagnosed brain gliomas: 59 patients had histologically verified high-grade gliomas: 37 glioblastomas multiform (GBM) and 22 anaplastic astrocytomas (AA), and 15 patients had low-grade gliomas. Apparent diffusion coefficient (ADC) values of tumor and peritumoral edema, and ADC ratios (ADC in tumor or peritumoral edema to ADC of contralateral white matter, as well as ADC in tumor to ADC in peritumoral edema) were determined from three regions of interest. The average of the mean, maximum, and minimum for ADC variables was calculated for each patient. The metabolite ratios of Cho/Cr and Cho/NAA at intermediate TE were assessed from spectral maps in the solid portion of tumor, peritumoral edema and contralateral normal-appearing white matter. Tumor grade determined with the two methods was then compared with that from histopathologic grading. Logistic regression and receiver operating characteristic (ROC) curve analysis were performed to determine optimum thresholds for tumor grading. Measures of diagnostic examination performance, such as sensitivity, specificity, PPV, NPV, AUC, and accuracy for identifying high-grade gliomas were also calculated

Kinetics of Cr(III) and Cr(VI) removal from water by two floating macrophytes.

Science.gov (United States)

Maine, M A; Hadad, H R; Sánchez, G; Caffaratti, S; Pedro, M C

2016-01-01

The aim of this work was to compare Cr(III) and Cr(VI) removal kinetics from water by Pistia stratiotes and Salvinia herzogii. The accumulation in plant tissues and the effects of both Cr forms on plant growth were also evaluated. Plants were exposed to 2 and 6 mg L(-1) of Cr(III) or Cr(VI) during 30 days. At the end of the experiment, Cr(VI) removal percentages were significantly lower than those obtained for Cr(III) for both macrophytes. Cr(III) removal kinetics involved a fast and a slow component. The fast component was primarily responsible for Cr(III) removal while Cr(VI) removal kinetics involved only a slow process. Cr accumulated principally in the roots. In the Cr(VI) treatments a higher translocation from roots to aerial parts than in Cr(III) treatments was observed. Both macrophytes demonstrated a high ability to remove Cr(III) but not Cr(VI). Cr(III) inhibited the growth at the highest studied concentration of both macrophytes while Cr(VI) caused senescence. These results have important implications in the use of constructed wetlands for secondary industrial wastewater treatment. Common primary treatments of effluents containing Cr(VI) consists in its reduction to Cr(III). Cr(III) concentrations in these effluents are normally below the highest studied concentrations in this work.

X-ray fluorescence analysis of Cr6+ component in mixtures of Cr2O3 and K2CrO4

International Nuclear Information System (INIS)

Tochio, Tatsunori; Sakakura, Shusuke; Oohashi, Hirofumi

2010-01-01

X-ray fluorescence analysis using Cr K α spectra was applied to the determination of the mixing ratio of Cr 6+ to (Cr 6+ + Cr 3+ ) in several mixtures of K 2 CrO 4 and Cr 2 O 3 . Because the powder of K 2 CrO 4 contained large particles that were more than 50 μm in diameter, it was ground between a pestle and a mortar for about 8 h. The coarse particles still remaining were removed by using a sieve with 325-mesh (44 μm) in order to reduce the difference in absorption effects between emissions from Cr 6+ and those from Cr 3+ . The mixing ratio, K 2 CrO 4 /(K 2 CrO 4 + Cr 2 O 3 ), of the five mixtures investigated is 0.50, 0.40, 0.20, 0.10, and 0.05 in weight, respectively. Each spectrum obtained was analyzed by decomposing it into two reference spectra, those of the two pure materials, K 2 CrO 4 and Cr 2 O 3 , with a constant background. The results for the mixtures containing K 2 CrO 4 of more than 20 wt% are that the relative deviation from the true value is less than ∼5%. On the other hand, when the content of K 2 CrO 4 decreases to less than 10 wt%, the relative deviation gets so large as 20 - 25%. The error coming from a peak separation of spectrum involved in our results were estimated by applying our method to five sets of data for each mixture computationally generated, taking into account the uncertainty in total counts of real measurements. (author)

X-ray fluorescence analysis of Cr(6+) component in mixtures of Cr(2)O(3) and K(2)CrO(4).

Science.gov (United States)

Tochio, Tatsunori; Sakakura, Shusuke; Oohashi, Hirofumi; Mizota, Hirohisa; Zou, Yanhui; Ito, Yoshiaki; Fukushima, Sei; Tanuma, Shigeo; Shoji, Takashi; Fujimura, Hajime; Yamashita, Michiru

2010-01-01

X-ray fluorescence analysis using Cr K(alpha) spectra was applied to the determination of the mixing ratio of Cr(6+) to (Cr(6+) + Cr(3+)) in several mixtures of K(2)CrO(4) and Cr(2)O(3). Because the powder of K(2)CrO(4) contained large particles that were more than 50 microm in diameter, it was ground between a pestle and a mortar for about 8 h. The coarse particles still remaining were removed by using a sieve with 325-mesh (44 microm) in order to reduce the difference in absorption effects between emissions from Cr(6+) and those from Cr(3+). The mixing ratio, K(2)CrO(4)/(K(2)CrO(4) + Cr(2)O(3)), of the five mixtures investigated is 0.50, 0.40, 0.20, 0.10, and 0.05 in weight, respectively. Each spectrum obtained was analyzed by decomposing it into two reference spectra, those of the two pure materials, K(2)CrO(4) and Cr(2)O(3), with a constant background. The results for the mixtures containing K(2)CrO(4) of more than 20 wt% are that the relative deviation from the true value is less than approximately 5%. On the other hand, when the content of K(2)CrO(4) decreases to less than 10 wt%, the relative deviation gets so large as 20 - 25%. The error coming from a peak separation of spectrum involved in our results were estimated by applying our method to five sets of data for each mixture computationally generated, taking into account the uncertainty in total counts of real measurements.

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2008-01-01

This is the 34th revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13 538 journal titles, 2 106 regularly scanned journals and 613 key journals. It was last updated in February 2008. A journal - or periodical - is a continuing publication issued in a succession of discrete parts, usually bearing numbering and/or chronological designations and intended to be continued indefinitely. It is generally published within a defined, fixed interval between issues and normally appears more than once per year. It includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as the Annual Review of Nuclear Science are included, but series titles such as the McGraw-Hill Series in Nuclear Engineering are not. The purpose of this document is to provide descriptive cataloguers with standard elements to include in bibliographic level 'S' of the INIS record. These elements include field (tag) 229 (Full Journal Title), 320 (ISSN) and 321 (CODEN). The full journal title is mandatory, and either the ISSN or the CODEN must be included (both may appear). Instructions on how to use this and other elements of the INIS record format are found in INIS: Guide to Bibliographic Description (IAEA-INIS-1). In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: - In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. - In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. - In Part III, all journals that are regularly scanned by

Preliminary Results on FeCrAl Alloys in the As-received and Welded State Designed to Have Enhanced Weldability and Radiation Tolerance

International Nuclear Information System (INIS)

Field, Kevin G.; Gussev, Maxim N.; Hu, Xunxiang; Yamamoto, Yukinori

2015-01-01

The present report summarizes and discusses the recent results on developing a modern, nuclear grade FeCrAl alloy designed to have enhanced radiation tolerance and weldability. The alloys used for these investigations are modern FeCrAl alloys based on a Fe-13Cr-5Al-2Mo-0.2Si-0.05Y alloy (in wt.%, designated C35M). Development efforts have focused on assessing the influence of chemistry and microstructure on the fabricability and performance of these newly developed alloys. Specific focus was made to assess the weldability, thermal stability, and radiation tolerance.

Preliminary Results on FeCrAl Alloys in the As-received and Welded State Designed to Have Enhanced Weldability and Radiation Tolerance

Energy Technology Data Exchange (ETDEWEB)

Field, Kevin G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gussev, Maxim N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hu, Xunxiang [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yamamoto, Yukinori [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-09-30

The present report summarizes and discusses the recent results on developing a modern, nuclear grade FeCrAl alloy designed to have enhanced radiation tolerance and weldability. The alloys used for these investigations are modern FeCrAl alloys based on a Fe-13Cr-5Al-2Mo-0.2Si-0.05Y alloy (in wt.%, designated C35M). Development efforts have focused on assessing the influence of chemistry and microstructure on the fabricability and performance of these newly developed alloys. Specific focus was made to assess the weldability, thermal stability, and radiation tolerance.

Bulk and surface properties of liquid Al-Cr and Cr-Ni alloys

International Nuclear Information System (INIS)

Novakovic, R

2011-01-01

The energetics of mixing and structural arrangement in liquid Al-Cr and Cr-Ni alloys has been analysed through the study of surface properties (surface tension and surface segregation), dynamic properties (chemical diffusion) and microscopic functions (concentration fluctuations in the long-wavelength limit and chemical short-range order parameter) in the framework of statistical mechanical theory in conjunction with quasi-lattice theory. The Al-Cr phase diagram exhibits the existence of different intermetallic compounds in the solid state, while that of Cr-Ni is a simple eutectic-type phase diagram at high temperatures and includes the low-temperature peritectoid reaction in the range near a CrNi 2 composition. Accordingly, the mixing behaviour in Al-Cr and Cr-Ni alloy melts was studied using the complex formation model in the weak interaction approximation and by postulating Al 8 Cr 5 and CrNi 2 chemical complexes, respectively, as energetically favoured.

Bulk and surface properties of liquid Al-Cr and Cr-Ni alloys.

Science.gov (United States)

Novakovic, R

2011-06-15

The energetics of mixing and structural arrangement in liquid Al-Cr and Cr-Ni alloys has been analysed through the study of surface properties (surface tension and surface segregation), dynamic properties (chemical diffusion) and microscopic functions (concentration fluctuations in the long-wavelength limit and chemical short-range order parameter) in the framework of statistical mechanical theory in conjunction with quasi-lattice theory. The Al-Cr phase diagram exhibits the existence of different intermetallic compounds in the solid state, while that of Cr-Ni is a simple eutectic-type phase diagram at high temperatures and includes the low-temperature peritectoid reaction in the range near a CrNi(2) composition. Accordingly, the mixing behaviour in Al-Cr and Cr-Ni alloy melts was studied using the complex formation model in the weak interaction approximation and by postulating Al(8)Cr(5) and CrNi(2) chemical complexes, respectively, as energetically favoured.

Land Titles and Rice Production in Vietnam

DEFF Research Database (Denmark)

Van Den Broeck, Katleen; Newman, Carol; Tarp, Finn

In most of the empirical literature on land titling, the household is regarded as unitary, and land rights are found to have ambiguous effects on land allocation, investment and productivity. Using data from 12 provinces in Vietnam, we diversify land titles, and show in a household fixed effects...... analysis of plot level rice yields that land titles are indeed important. Only exclusively held titles have the expected positive effects, and the positive effect on yields is found in male headed households. Furthermore, a household level rice yield function reveals that exclusive user rights...... are inefficiency decreasing, while jointly held user rights have no efficiency effects. Finally, once the gender of the head of household is controlled for, exclusively held female titles have a greater positive effect on the efficiency of the household than that of male held titles...

Biliary excretion and distribution of 51Cr(III) and 51Cr(VI) in rats

International Nuclear Information System (INIS)

Cikrt, M.; Bencko, V.

1979-01-01

The biliary excretion and distribution of 51 Cr after intravenous administration of 51 Cr(III) ( 51 CrCl 3 ) or 51 Cr(VI) (Na 2 51 CrO 4 .4H 2 O) were studied in rats. The cumulative biliary excretion of 51 Cr 24 hrs after the injection was significantly higher after administration of 51 Cr(VI) than of 51 Cr(III) (3.51+-0.7% and 0.51+-0.05% of administered dose, respectively). This difference was especially due to a higher rate of biliary excretion of 51 Cr in the first hours after 51 Cr(VI) administration. The excretion of 51 Cr via feces was also higher after administration of 51 Cr(VI) (7.35+-0.45%) of administered dose, as against 4.23+-0.23% after 51 Cr(III). On the other hand, no significant difference in urinary excretion of 51 Cr was found. Statistically significant differences were also observed in the distribution of 51 Cr in the organism after administration of both valence states of the metal. (author)

Microstructure and mechanical properties of nanostructure multilayer CrN/Cr coatings on titanium alloy

International Nuclear Information System (INIS)

Wiecinski, Piotr; Smolik, Jerzy; Garbacz, Halina; Kurzydlowski, Krzysztof J.

2011-01-01

Five different nanostructured, multilayer coatings (CrN/Cr)x8 with different thickness ratio of Cr and CrN layers were deposited by PAPVD (Plasma Assisted Physical Vapour Deposition) vacuum arc method on Ti6Al4V titanium alloy. The microstructure, chemical and phase composition of the CrN and Cr sub-layers were characterized by SEM with EDX and Cs-corrected dedicated STEM on cross-sections prepared by focus ion beam. Besides, hardness and Young's modulus of the (Cr/CrN)x8 coatings has been measured. The adhesion has been tested by scratch test method. The obtained (CrN/Cr) multilayer coatings, 5-6 μm in thickness, have homogeneous and nanocrystalline structure, free of pores and cracks. The microstructures of Cr and CrN layers consist of columnar grains below 100 nm in diameter. The hardness and Young's modulus of these coatings depend linearly on thickness ratio of Cr and CrN layers. The decrease of the thickness ratio Cr/CrN 0.81 to 0.15 results in the increase of hardness from 1275 HV to 1710 HV and Young's modulus from 260 GPa to 271 GPa.

Effect of Layer-Graded Bond Coats on Edge Stress Concentration and Oxidation Behavior of Thermal Barrier Coatings

Science.gov (United States)

Zhu, Dongming; Ghosn, Louis J.; Miller, Robert A.

1998-01-01

Thermal barrier coating (TBC) durability is closely related to design, processing and microstructure of the coating Z, tn systems. Two important issues that must be considered during the design of a thermal barrier coating are thermal expansion and modulus mismatch between the substrate and the ceramic layer, and substrate oxidation. In many cases, both of these issues may be best addressed through the selection of an appropriate bond coat system. In this study, a low thermal expansion and layer-graded bond coat system, that consists of plasma-sprayed FeCoNiCrAl and FeCrAlY coatings, and a high velocity oxyfuel (HVOF) sprayed FeCrAlY coating, is developed to minimize the thermal stresses and provide oxidation resistance. The thermal expansion and oxidation behavior of the coating system are also characterized, and the strain isolation effect of the bond coat system is analyzed using the finite element method (FEM). Experiments and finite element results show that the layer-graded bond coat system possesses lower interfacial stresses. better strain isolation and excellent oxidation resistance. thus significantly improving the coating performance and durability.

Cr-Ni ALLOY ELECTRODEPOSITION AND COMPARISON WITH CONVENTIONAL PURE Cr COATING TECHNIQUE

Directory of Open Access Journals (Sweden)

M. Moniruzzaman

2012-12-01

Full Text Available Cr coating is widely used as the outer surface of precision parts due to its attractive appearance and superior corrosion resistance properties. It is obtained by electrodeposition via a conventional bath with hexavalent Cr ions. This manufacturing technique has many drawbacks, such as very low efficiency and high operating temperature and it is hazardous to health. In this work, we studied a Cr-Ni alloy deposition technique and compared the alloy coating properties to those with conventional Cr coating. Sequential two-step alloy electrodeposition was also compared. We took varying concentrations of Cr, Ni and complexing agents for the electrodeposition of Cr-Ni alloy and sequential Cr-Ni alloy coating on mild steel. Operating parameters, i.e. current density and temperature, were varied to examine their effects on the coating properties. The coatings thus obtained were characterized by visual observation, corrosion test, microhardness measurement, morphology and chemical analysis. The Cr-Ni alloy coating was found to be more corrosion resistant in 5% NaCl solution and harder than the pure Cr coating obtained by conventional electrodeposition. Toxic gas was produced in a much lower extent in the alloy coating than the conventional Cr coating technique. Again, the two-step Cr-Ni alloy coating was found better in terms of corrosion resistance as well as hardness compared to the Cr-Ni alloy coating. The process was also found to be much more environmentally friendly.

Electronic structure and magnetic ordering of the semiconducting chromium trihalides CrCl3, CrBr3, and CrI3

KAUST Repository

Wang, Hao

2011-03-01

We present results from an electronic structure investigation of the chromium halides CrCl3, CrBr3, and CrI3, as obtained by the linearized augmented plane wave method of density functional theory. Our interest focuses on the chloride. While all three halides display strong ferromagnetic coupling within the halide-Cr-halide triple layers, our emphasis is on differences in the interlayer magnetic coupling. In agreement with experimental results, our calculations indicate ferromagnetic ordering for CrBr3 as well as CrI3. The antiferromagnetic state of CrCl3 can be reproduced by introducing an on-site electron-electron repulsion. However, we observe that the ground state depends critically on the specific approach used. Our results show that a low temperature structural phase transition from monoclinic to trigonal is energetically favourable for CrCl3. © 2011 IOP Publishing Ltd.

Quarterly title list for the period ending June 1980

International Nuclear Information System (INIS)

1980-01-01

The title list contains: a) 17 titles and abstracts of laboratory reports, b) 36 titles of publications (32 with abstracts), c) 13 titles of articles submitted for publication (12 with abstracts), and d) 72 titles of lectures (52 with abstracts.) (GG) [de

Title of the paper goes here second line

Indian Academy of Sciences (India)

%%Please download if these packages are not included %%in your local TeX distribution %%txfonts,balance,textcase,float %% \\begin{document} %%paper title %%For line breaks, \\\\ can be used within title \\title{Title of the paper goes here\\\\ second line} %%author names are separated by comma (,) %%use \\and before ...

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2009-01-01

This is the 35th revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13 750 journal titles, 1 965 regularly scanned journals and 593 key journals. It was last updated in March 2009. A journal - or periodical - is a continuing publication issued in a succession of discrete parts, usually bearing numbering and/or chronological designations and intended to be continued indefinitely. It is generally published within a defined, fixed interval between issues and normally appears more than once per year. It includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as the Annual Review of Nuclear Science are included, but series titles such as the McGraw-Hill Series in Nuclear Engineering are not. The purpose of this document is to provide descriptive cataloguers with standard elements to include in bibliographic level 'S' of the INIS record. These elements include field (tag) 229 (Full Journal Title), 320 (ISSN) and 321 (CODEN). The full journal title is mandatory, and either the ISSN or the CODEN must be included (both may appear). Instructions on how to use this and other elements of the INIS record format are found in INIS: Guide to Bibliographic Description (IAEA-INIS-1). In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: - In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. - In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. - In Part III, all journals that are regularly scanned by the

24 CFR 203.385 - Types of satisfactory title evidence.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Types of satisfactory title... Title Waivers § 203.385 Types of satisfactory title evidence. The following types of title evidence shall be satisfactory to the Commissioner: (a) Fee or owner's title policy. A fee or owner's policy of...

Structure and magnetic properties of Cr nanoparticles and Cr2O3 nanoparticles

International Nuclear Information System (INIS)

Zhang, W.S.; Brueck, E.; Zhang, Z.D.; Tegus, O.; Li, W.F.; Si, P.Z.; Geng, D.Y.; Buschow, K.H.J.

2005-01-01

We have synthesized Cr nanoparticles by arc-discharge and Cr 2 O 3 nanoparticles by subsequent annealing the as-prepared Cr nanoparticles. The structure of these nanoparticles is studied by means of X-ray diffraction, X-ray photoelectron spectroscopy, and high-resolution transmission electron microscope. Most of the particles show a good crystal habit of well-defined cubic or orthorhombic shape, while some small particles show spherical shape. The as-prepared Cr nanoparticles have a BCC Cr core coated with a thin Cr 2 O 3 layer. Cr in the core of the particles heated at 873 K for 4 h is changed to Cr 2 O 3 . The results of magnetic measurements show that the Cr nanoparticles exhibit mainly antiferromagnetic properties, in addition to a weak-ferromagnetic component at lower fields. The weak-ferromagnetic component may be ascribed to uncompensated surface spins. For the field-cooled Cr 2 O 3 nanoparticles, an exchange bias is observed in the hysteresis loops, which can be interpreted as the exchange coupling between the uncompensated spins at the surface and the spins in the core of the Cr 2 O 3 nanoparticles

Second Annual Progress Report on Radiation Tolerance of Controlled Fusion Welds in High Temperature Oxidation Resistant FeCrAl Alloys

Energy Technology Data Exchange (ETDEWEB)

Field, Kevin G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gussev, Maxim N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yamamoto, Yukinori [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Howard, Richard H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Briggs, Samuel A. [Univ. of Wisconsin, Madison, WI (United States)

2016-12-30

The present report summarizes and discusses the current results and on-going activity towards developing a modern, nuclear grade FeCrAl alloy designed to have enhanced radiation tolerance and weldability under the Department of Energy (DOE) Nuclear Energy Enabling Technologies (NEET) program.

Grading School Choice: Evaluating School Choice Programs by the Friedman Gold Standard. School Choice Issues in Depth

Science.gov (United States)

Enlow, Robert C.

2008-01-01

In 2004, The Friedman Foundation for Educational Choice published a report titled "Grading Vouchers: Ranking America's School Choice Programs." Its purpose was to measure every existing school choice program against the gold standard set by Milton and Rose Friedman: that the most effective way to improve K-12 education and thus ensure a stable…

1-ethyl gallate-2-substituted phenoxymethyl benzimidazoles: synthesis, molecular structure, antimicrobial activities and complex with cr(iii)

International Nuclear Information System (INIS)

Zhao, L.; Wu, J.; Wu, J.; Wang, Z.; Gu, H.

2017-01-01

The design of gallate and benzimidazole containing derivatives is expected to produce new bioactive molecules with multiple applications. Here the synthesis of eight novel benzimidazole compounds containing ethyl gallate and substituted phenoxymethyl units are reported. Firstly, the ring closure reaction between o-phenylendiamine and substituted phenoxyacetic acids resulted in 2-substituted phenoxymethyl benzimidazoles that were then modified by the N-hydroxyethylation with 2-chloroethyl alcohol under a phase transfer catalysis condition. The obtained 1-hydroxyethyl-2-substituted phenoxymethyl benzimidazoles were finally translated into the target title compounds 8a-h by an indirect esterification method in which three O-H groups of gallic acid were first protected by acetyls and deprotected after the esterification reaction by adding hydrazine hydrate. The structures of the title products 8a-h were fully characterized and confirmed by elemental analysis, MS, IR, 1H-NMR, 13C-NMR and single crystal X-ray diffraction techniques. Antimicrobial tests by inhibition zones indicated that these compounds exhibited diverse inhibitory effects against the test bacteria and fungi, and the type and position of the substituent groups in the phenoxymethyl moieties had obvious influence on their antimicrobial activities. Furthermore, the Cr(III) complex of 8h was synthesized, and various spectral, elemental and thermal analysis results confirmed that the central Cr(III) atom coordinated with adjacent hydroxyl groups of two 8h ligands, nitrate and H2O, respectively. (author)

Formulating the Right Title for a Research Article.

Science.gov (United States)

Bavdekar, Sandeep B

2016-02-01

Title is an important part of the article. It condenses article content in a few words and captures readers' attention. A good title for a research article is the one which, on its own, is able to introduce the research work to the fullest extent, but in a concise manner. Writing scientific titles that are informative and attractive is a challenging task. This communication describes the importance of titles and the methods of creating appropriate titles for research papers. © Journal of the Association of Physicians of India 2011.

Homogeneous and Heterogeneous (Fex, Cr1-x)(OH)3 Precipitation: Implications for Cr Sequestration.

Science.gov (United States)

Dai, Chong; Zuo, Xiaobing; Cao, Bo; Hu, Yandi

2016-02-16

The formation of (Fe, Cr)(OH)3 nanoparticles determines the fate of aqueous Cr in many aquatic environments. Using small-angle X-ray scattering, precipitation rates of (Fe, Cr)(OH)3 nanoparticles in solution and on quartz were quantified from 0.1 mM Fe(III) solutions containing 0-0.25 mM Cr(III) at pH = 3.7 ± 0.2. Concentration ratio of aqueous Cr(III)/Fe(III) controlled the chemical composition (x) of (Fex, Cr1-x)(OH)3 precipitates, solutions' supersaturation with respect to precipitates, and the surface charge of quartz. Therefore, the aqueous Cr(III)/Fe(III) ratio affected homogeneous (in solution) and heterogeneous (on quartz) precipitation rates of (Fex, Cr1-x)(OH)3 through different mechanisms. The sequestration mechanisms of Cr(III) in precipitates were also investigated. In solutions with high aqueous Cr(III)/Fe(III) ratios, surface enrichment of Cr(III) on the precipitates occurred, resulting in slower particle growth in solutions. From solutions with 0-0.1 mM Cr(III), the particles on quartz grew from 2 to 4 nm within 1 h. Interestingly, from solution with 0.25 mM Cr(III), particles of two distinct sizes (2 and 6 nm) formed on quartz, and their sizes remained unchanged throughout the reaction. Our study provided new insights on homogeneous and heterogeneous precipitation of (Fex, Cr1-x)(OH)3 nanoparticles, which can help determine the fate of Cr in aquatic environments.

Development of nuclear grade stainless steels at KCSSL

International Nuclear Information System (INIS)

Balachandran, G.; Dhere, M.; Mahadik, A.; Hinge, N.M.; Balasubramanian, V.

2011-01-01

Kalyani Carpenter Special Steels Ltd is an alloy steel plant, where a variety of alloy steel grades are produced for automotive, defence, nuclear and aerospace applications. The plant has developed expertise in processing of several alloy steel grades of superior quality that meets stringent specifications. Primary steel is processed through a combination of electric arc furnace, ladle furnace and vacuum degassing where stringent control over dephosphorisation, desulphurization, deoxidation is effected to get a refined high quality steel. The molten steel is cast through continuous casting of slabs or ingot casting. In grades specific to nuclear application, the primary cast products are further subjected to electroslag remelting to achieve further freedom from inclusions and to achieve a favourable solidification grain structure, which ultimately improve the hot workability of the alloy steel. Appropriate choice of slag and operating parameters are needed for realising the required ingot quality. The present study would examine the processing and quality aspects of some important grades of steels used in nuclear industry namely ferritic 9Cr-1Mo steel, martensitic stainless steels 403, 410, precipitation hardenable 17-4 PH stainless steel and austenitic 321, 316LN stainless steel, which were made and supplied for applications to Indian nuclear industry. The expertise developed in processing the steels in terms of melting, heat treatment and their relationship to structural features and mechanical properties would be highlighted. (author)

Hot corrosion of Co-Cr, Co-Cr-Al, and Ni-Cr alloys in the temperature range of 700-750 deg C

Science.gov (United States)

Chiang, K. T.; Meier, G. H.

1980-01-01

The effect of SO3 pressure in the gas phase on the Na2SO4 induced hot corrosion of Co-Cr, Ni-Cr, and Co-Cr-Al alloys was studied in the temperature range 700 to 750 C. The degradation of the Co-Cr and Ni-Cr alloys was found to be associated with the formation of liquid mixed sulfates (CoSO4-Na2SO4 or NiSO4-Na2SO4) which provided a selective dissolution of the Co or Ni and a subsequent sulfidation oxidation mode of attack which prevented the maintenance of a protective Cr2O3 film. A clear mechanism was not developed for the degradation of Co-Cr-Al alloys. A pitting corrosion morphology was induced by a number of different mechanisms.

Nano-mineralogy and -geochemistry of high-grade diasporic karst-type bauxite from Parnassos-Ghiona mines, Greece

DEFF Research Database (Denmark)

Gkamaletsos, Platon; Godelitsas, Athanasios; Kasama, Takeshi

2017-01-01

and electron microscopy in microscale and mesoscale (SEM-EDS including STEM mode), proved the presence of “Fe-Cr-Ti-containing diaspore”, anatase and minor rutile. The study by means of 57Fe Mössbauer spectroscopy, in correlation with magnetic susceptibility measurements and, complemented, with Synchrotron......In the present work, a combination of various techniques is utilized for the study of nano-mineralogy and -geochemistry of high-grade karst-type bauxite (Al-rich and Fe-depleted samples; Al2O3 ca. 80 wt.%) from the Parnassos-Ghiona mines located in Greece. Initial characterization using PXRD......-based spectroscopies at the microscale (SR micro-XRF and micro-XANES/-EXAFS), indicated that Fe3+, in contrast to [6]Cr3+, is not exclusively a component of the diaspore structure. While Cr3 + substitutes Al3 + in octahedral sites of diaspore ([6]Cr3+ ↔ [6]Al3+), the electron microscopy in nanoscale (TEM-EDS & EELS...

Quarterly title list for the period ending September 1976

International Nuclear Information System (INIS)

1976-01-01

The title list of the Max-Planck-Institut fuer Plasmaphysik and the Projektgruppe fuer Laserforschung of the MPG is concerned with the period from July until September 1976, and it contains: a) 12 titles and abstracts of laboratory reports, b) 37 titles of publications (30 abstracts), c) 20 titles of articles submitted for publication (16 abstracts), and d) 25 titles of lectures (12 abstracts). (GG) [de

Chromium sorption and Cr(VI) reduction to Cr(III) by grape stalks and yohimbe bark.

Science.gov (United States)

Fiol, Núria; Escudero, Carlos; Villaescusa, Isabel

2008-07-01

In this work, two low cost sorbents, grape stalks and yohimbe bark wastes were used to remove Cr(VI) and Cr(III) from aqueous solutions. Batch experiments were designed to obtain Cr(VI) and Cr(III) sorption data. The mechanism of Cr(III) and Cr(VI) removal and Cr(VI) reduction to Cr(III) by the two vegetable wastes, has been investigated. Fourier transform infrared rays (FTIR) and X-ray photoelectron spectroscopy (XPS) analysis on solid phase were performed to determine the main functional groups that might be involved in metal uptake and to confirm the presence of Cr(III) on the sorbent, respectively. Results put into evidence that both sorbents are able to reduce Cr(VI) to its trivalent form.

First-Principles Calculations for Chemical Reaction between Sodium Diethyldithiocarbamate and Transition-Metal (Cr) atom to Produce Cr(DDC)3 and Cr(DDC)2ODDC

Science.gov (United States)

Setiyanto, Henry; Muhida, Rifki; Kishi, Tomoya; Rempillo, Ofelia; Rahman, Mahmudur; Dipojono, Hermawan Kresno; Di\\ {n}o, Wilson Agerico; Matsumoto, Shigeno; Kasai, Hideaki

2006-10-01

We investigate the chemical reaction between a Cr transition-metal atom and sodium diethyldithiocarbamate (NaDDC), a complexing agent used to detect and extract Cr in human blood samples. Using density-functional-theory-based calculations, we determine their stable structures of Cr(DDC)2ODDC and Cr(DDC)3 complexes and obtain their dissociation energies. We found dissociation energies of -10.66 and -3.24 eV for Cr(DDC)2ODDC and Cr(DDC)3 complexes, respectively. Hence, on the basis of dissociation energies, we have verified that the reaction of NaDDC with Cr produces Cr(DDC)2ODDC as a major product.

Casi Víspera / Colibrí Resucitado Crónica

Directory of Open Access Journals (Sweden)

Susana Chávez-Silverman

2017-05-01

Full Text Available Abstract Susana Chávez-Silverman is a Califas-born U.S. Latina writer and flaneuse who (against all odds is also an educator, although she mostly laments what’s happened to la cacademia over the last decade or so. She still finds joy and hope in being la High Priestess of SLOW to her students and former students, some of which are among her closest compinches. Of the two crónicas included in this special curated issue of cultural works in PORTAL under the theme Transitions and Dislocations, she says:   ‘My writing/life took a major detour in 2016. For most of the year, I wrote nothing at all. Or rather, nothing except e-mail after email: to administrators, colleagues all over the world, attorneys, friends and relatives. I had scheduled my sabbatical in order to finish a book project, but had been derailed by a Title IX investigation and plagiarism case at my home institution, and the accompanying anxiety and anger . I returned to my book over the summer, culling and editing hundreds of pages of primary texts (letters and emails. But this book is much longer—and truer—than anything I’ve written before and takes a different kind of writing energy, uninterrupted time, and commitment. Writing from a place of anger and anxiety doesn’t serve this book. The two crónicas included in this special curated issue are not part of my book in progress, Our Ubuntu, Montenegro: del Balboa Café al Apartheid and Back. Rather, they were my way of easing back into my (heart space. ‘Casi Víspera’ proves I did write something in 2016 after all (other than email, I mean—I had no memory of it until early this year! ‘Black Holes’ talks about precisely this (remembering and not. I was determined not to let 2016’s plagiarism/Title IX toxic double helix continue to poison me. I wanted to begin 2017 with a bang, and wrote this for my son, for his 30th birthday.’

The effects of graded levels of calorie restriction: IV. Non-linear change in behavioural phenotype of mice in response to short-term calorie restriction.

Science.gov (United States)

Lusseau, David; Mitchell, Sharon E; Barros, Ceres; Derous, Davina; Green, Cara; Chen, Luonan; Han, Jing-Dong Jackie; Wang, Yingchun; Promislow, Daniel E L; Douglas, Alex; Speakman, John R

2015-08-25

Animals have to adjust their activities when faced with caloric restriction (CR) to deal with reduced energy intake. If CR is pronounced, allostasis can push individuals into alternate physiological states which can result in important health benefits across a wide range of taxa. Here we developed a new approach to determine the changes in behavioural phenotype associated with different levels of CR. We exposed C57BL/6 male mice to graded CR (from 0 to 40%) for three months and defined their behavioural phenotype using hidden Markov models of their movement and body temperature. All 40% CR mice exhibited a state-shift in behavioural phenotype and only some exposed to 30% CR did. We show for the first time that mice changed their activity characteristics rather than changed their activities. This new phenotyping approach provides an avenue to determine the mechanisms linking CR to healthspan.

24 CFR 202.11 - Title I.

Science.gov (United States)

2010-04-01

... in 24 CFR 25.5. Civil money penalties may be imposed against Title I lenders and mortgagees pursuant... unacceptable risk to the Department; or (iv) Transfer of a Title I loan to a party that does not have a valid...

In silico CrNF, a half-metallic ferromagnetic nitride–fluoride mimicking CrO2

International Nuclear Information System (INIS)

Matar, Samir F.

2014-01-01

Isoelectronic with CrO 2 , CrNF is proposed in silico based on rutile derived structures with DFT computations. The ground state structure defined from cohesive energies is of MgUO 4 -type, characterized by short covalent Cr–N and long ionic Cr–F distances. Like CrO 2 it is a half-metallic ferromagnet with M=2 μ B /FU integer magnetization with reduced band gap at minority spins. Major difference of magnetic response to pressure characterizes CrNF as a soft ferromagnet versus hard magnetic CrO 2 . The chemical bonding properties point to prevailing covalent Cr–N versus ionic Cr–F bonding. Different synthesis routes are examined. - Highlights: • DFT identification of CrNF is based on isoelectronicity and rutile derivatives. • Similarly to CrO 2 , CrNF is a half-metallic ferromagnet with reduced band gap. • Strong pressure dependence of magnetization of CrNF oppositely to CrO 2 . • Covalent Cr–N bonding prevails in spite of the presence of ionic Cr–F. • Cohesive energies favor the synthesis for which protocols are proposed

Correlation of microstructure and fracture toughness of advanced 9Cr/CrMoV dissimilarly welded joint

Energy Technology Data Exchange (ETDEWEB)

Guo, Qian [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Lu, Fenggui, E-mail: Lfg119@sjtu.edu.cn [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Liu, Xia [Shanghai Turbine Plant of Shanghai Electric Power Generation Equipment Co. Ltd., Shanghai 200240 (China); Yang, Renjie [Shanghai Turbine Works Company, Shanghai 200240 (China); Cui, Haichao [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Gao, Yulai, E-mail: ylgao@shu.edu.cn [State Key Laboratory of Advanced Special Steels, Shanghai University, Shanghai 200072 (China)

2015-06-25

In this paper, the fracture toughness and the related microstructure characteristics of dissimilarly welded joint manufactured by advanced 9Cr and CrMoV steels were systematically investigated. The dissimilarly welded joint was fabricated by narrow gap submerged arc welding (NG-SAW) applying multi-layer and multi-pass technique. Fracture toughness, as one of the most important property to assess the reliability of welded joint, was studied for different regions including CrMoV base metal (CrMoV-BM), heat affected zone (HAZ) of CrMoV side (CrMoV-HAZ), weld metal (WM), heat affected zone of 9Cr side (9Cr-HAZ) and 9Cr base metal (9Cr-BM). It was found that the fracture toughness of CrMoV-BM, CrMoV-HAZ and WM was better than that of 9Cr-HAZ and 9Cr-BM. In order to illustrate these results, the microstructure of the whole welded joint was observed by optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM) detailedly. It was found that the fine high-temperature tempered martensite and bainite in WM, CrMoV-BM and CrMoV-HAZ contribute to the higher fracture toughness, while lower fracture toughness for 9Cr-BM and HAZ was caused by coarse tempered lath-martensite. Furthermore, the fracture morphology showed that ductile fracture occurred in WM and CrMoV side, while brittle fracture appeared in BM and HAZ of 9Cr side.

How property title impacts urban consolidation

DEFF Research Database (Denmark)

Easthope, Hazel; Warnken, Jan; Sherry, Cathy

2014-01-01

Continuing urbanisation is triggering an increase in multi-titled housing internationally. This trend has given rise to a substantial research interest in the social consequences of higher density living. Little enquiry, however, has been directed to examining how property title subdivisions gene...

Low-field spin dynamics of Cr7Ni and Cr7Ni-Cu -Cr 7Ni molecular rings as detected by μ SR

Science.gov (United States)

Sanna, S.; Arosio, P.; Bordonali, L.; Adelnia, F.; Mariani, M.; Garlatti, E.; Baines, C.; Amato, A.; Sabareesh, K. P. V.; Timco, G.; Winpenny, R. E. P.; Blundell, S. J.; Lascialfari, A.

2017-11-01

Muon spin rotation measurements were used to investigate the spin dynamics of heterometallic Cr7Ni and Cr7Ni -Cu-Cr7Ni molecular clusters. In Cr7Ni the magnetic ions are arranged in a quasiplanar ring and interact via an antiferromagnetic exchange coupling constant J , while Cr7Ni -Cu-Cr7Ni is composed of two Cr7Ni linked by a bridging moiety containing one Cu ion, that induces an inter-ring ferromagnetic interaction J'≪J . The longitudinal muon relaxation rate λ collected at low magnetic fields μ0H BPP)-like heuristic fitting model that takes into account of a distribution of electronic spin characteristic times for T >5 K, while the shoulder presented by Cr7Ni can be reproduced by a BPP function that incorporates a single electronic characteristic time theoretically predicted to dominate for T <5 K. The flattening of λ (T ) in Cr7Ni -Cu-Cr7Ni occurring at very low temperature can be tentatively attributed to field-dependent quantum effects and/or to an inelastic term in the spectral density of the electronic spin fluctuations.

Cr(III) and Cr(VI) in leather and elicitation of eczema

DEFF Research Database (Denmark)

Hansen, Malene Barré; Menne, Torkil; Johansen, Jeanne Duus

2006-01-01

The aim of the present study was to investigate the relation between the content of Cr(VI) and soluble Cr(III) in leather and the ability of the leather to elicit eczema in chromium allergic patients. An array of chromium-tanned leather samples was analysed for the content of total Cr(VI) and sol...

The ties that bind: what's in a title?

Science.gov (United States)

Neuhaus, Susan J

2018-03-01

Many Australian and New Zealand surgeons use the title 'Mister' rather than 'Doctor', a practice dating back to traditions established over 600 years ago. The Royal Australasian College of Surgeons is currently undergoing a period of critical self-reflection, embodied by its 'Respect' campaign. Active measures to embrace diversity and encourage women into surgery are underway. This paper reviews the historical basis to the use of gendered titles and their current use amongst fellows. De-identified demographic data from the college register of active fellows was searched by self-identified title, country or state, and gender. Data were further reviewed by surgical sub-specialty and year of fellowship. The college dataset suggests that there is significant variance in the preference for gendered titles, determined predominantly by geography rather than specialty. The highest use of gendered titles (by male and female surgeons) was in Victoria/Tasmania (58% male, 22% female) and New Zealand (81% male, 17% female). By contrast, only 2% of female surgeons in other states elected a gendered title (Miss/Mrs/Ms). Surgery is the only profession that continues to use gendered titles. As the College of Surgeons moves towards greater equity and diversity, consideration should be given to phasing out the use of gendered titles, which serve to divide rather than unite our profession. © 2017 Royal Australasian College of Surgeons.

40 CFR 300.220 - Related Title III issues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 27 2010-07-01 2010-07-01 false Related Title III issues. 300.220 Section 300.220 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SUPERFUND, EMERGENCY... PLAN Planning and Preparedness § 300.220 Related Title III issues. Other related Title III requirements...

Electronic structure and magnetic ordering of the semiconducting chromium trihalides CrCl3, CrBr3, and CrI3

KAUST Repository

Wang, Hao; Eyert, Volker; Schwingenschlö gl, Udo

2011-01-01

for CrBr3 as well as CrI3. The antiferromagnetic state of CrCl3 can be reproduced by introducing an on-site electron-electron repulsion. However, we observe that the ground state depends critically on the specific approach used. Our results show that a

Mathematical models applied to the Cr(III) and Cr(VI) breakthrough curves.

Science.gov (United States)

Ramirez C, Margarita; Pereira da Silva, Mônica; Ferreira L, Selma G; Vasco E, Oscar

2007-07-19

Trivalent and hexavalent chromium continuous biosorption was studied using residual brewer Saccharomyces cerevisiae immobilized in volcanic rock. The columns used in the process had a diameter of 4.5 cm and a length of 140 cm, working at an inlet flow rate of 15 mL/min. Breakthrough curves were used to study the yeast biosorption behavior in the process. The saturation time (ts) was 21 and 45 h for Cr(III) and Cr(VI), respectively, and a breakthrough time (tb) of 4 h for Cr(III) and 5 h for Cr(VI). The uptake capacity of the biosorbent for Cr(III) and Cr(VI) were 48 and 60 mg/g, respectively. Two non-diffusional mathematical models with parameters t0 and sigma were used to adjust the experimental data obtained. Microsoft Excel tools were used for the mathematical solution of the two parameters used.

The lattice distortion effect for zinc-blende CrAs and CrSb

International Nuclear Information System (INIS)

Yamana, Keita; Geshi, Masaaki; Tsukamoto, Hidekazu; Uchida, Ichiro; Shirai, Masafumi; Kusakabe, Koichi; Suzuki, Naoshi

2004-01-01

We investigated the stability of the ferromagnetism of CrAs and CrSb in the zinc-blende structure against the lattice distortion, systematically. A calculation within the generalized gradient approximation using a full potential linearized augmented plane wave method was performed. We compared the ferromagnetic state and the antiferromagnetic state assuming tetragonal distortion with the lattice constants a and c changing independently and determined the spin polarization ratio in the ferromagnetic phase. The result shows that complete spin polarization (half-metallic ferromagnetism) remains stable even in the presence of large tetragonal distortion. On the other hand, our calculation shows that two monolayers of CrAs is enough to produce a half-metallic state in the CrAs/GaAs multilayer. Thus, the present result suggests that the half-metallic nature persists in various atomic-scale superlattices made of distorted CrAs or CrSb

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 437 ... Journal Home > Advanced Search > Browse Title Index ... prospects and realistic strategies to its implementation in Nigeria\\'s Institute of ... and Communication Technology (ICT) in information dissemination, Abstract.

Browse Title Index

African Journals Online (AJOL)

1986), University Engineering Education and Training in Nigeria: Development, ... Vol 29, No 1 (2010), Use of Energy Method to Simulate the ... of Optimal Rational Composition of Titles Producible from Nigerian Clays ...

Roadmap Through Title XX. Financing Services for Children Through Title XX and Other Programs: Manual 5.

Science.gov (United States)

Copeland, William C.; Iversen, Iver A.

This manual, part of a Hecht Institute four-manual series entitled Financing Children's Services Through Title XX and Related Programs, teaches what Title XX regulations are, what they mean, and what actions and procedures are commanded by them. The first section covers the necessity of rule systems, the characteristics of a good rule system and…

Cardiac rehabilitation: impact of graded exercise in the recovery period following myocardial infarction

Directory of Open Access Journals (Sweden)

White S

2013-07-01

Full Text Available Simon WhiteSchool of Pharmacy, Keele University, Staffordshire, UKAbstract: This paper reviews the impact of graded exercise undertaken as part of a cardiac rehabilitation (CR program in the recovery period following a myocardial infarction, focusing on how CR may be best provided and the evidence-base relating to exercise-based CR. Essential components of CR are considered here to include education about healthy behavior, lifestyle modification where necessary (especially in relation to smoking, diet, and physical exercise, medical risk factor management, use of cardioprotective medicines and implantable devices, and psychosocial health management. It is argued that the totality of the evidence continues to demonstrate benefits of exercise-based CR in terms of mortality and morbidity, despite the debate about the magnitude of that benefit. However, given the wide variance in the quality and nature of CR service provision, there is no guarantee that patients eligible for CR will benefit fully. In line with national and international standards, CR should be tailored to the patient's individual needs, but structured exercise is recommended for most patients. Exercise sessions, whether based in hospital, in the community, or at home, should be designed to vary the frequency, intensity, duration, and type of exercise. They must include an initial warm-up period, before a conditioning period, and finish with a cool-down period. Patients should be taught to self-monitor so that they can exercise safely on their own. In designing interventions to support patients to change health behavior, health professionals should recognize that patients may only make lifestyle modifications to aspects of lifestyle perceived as causes of their cardiovascular disease and so, for example, may not do the recommended amount of exercise if they do not perceive lack of exercise to be a cause of their cardiovascular disease.Keywords: cardiovascular disease, public health

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 346 ... Journal Home > Advanced Search > Browse Title Index ... and hygiene promotion services in Rungwe district, Tanzania, Abstract .... as seen in NIgerian teaching hospital: pattern and a simple classification, Abstract.

33 CFR 401.1 - Short title.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Short title. 401.1 Section 401.1 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT CORPORATION, DEPARTMENT OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations § 401.1 Short title. These regulations may be cited as the...

Potential applications of Pseudomonas sp. (strain CPSB21) to ameliorate Cr6+ stress and phytoremediation of tannery effluent contaminated agricultural soils.

Science.gov (United States)

Gupta, Pratishtha; Rani, Rupa; Chandra, Avantika; Kumar, Vipin

2018-03-20

Contamination of agricultural soil with heavy metals has become a serious concern worldwide. In the present study, Cr 6+ resistant plant growth promoting Pseudomonas sp. (strain CPSB21) was isolated from the tannery effluent contaminated agricultural soils and evaluated for the plant growth promoting activities, oxidative stress tolerance, and Cr 6+ bioremediation. Assessment of different plant growth promotion traits, such as phosphate solubilization, indole-3-acetic acid production, siderophores, ammonia and hydrogen cyanide production, revealed that the strain CPSB21 served as an efficient plant growth promoter under laboratory conditions. A pot experiment was performed using sunflower (Helianthus annuus L.) and tomato (Solanum lycopersicum L.) as a test crop. Cr 6+ toxicity reduced plant growth, pigment content, N and P uptake, and Fe accumulation. However, inoculation of strain CPSB21 alleviated the Cr 6+ toxicity and enhanced the plant growth parameters and nutrient uptake. Moreover, Cr toxicity had varied response on oxidative stress tolerance at graded Cr 6+ concentration on both plants. An increase in superoxide dismutase (SOD) and catalase (CAT) activity and reduction in malonialdehyde (MDA) was observed on inoculation of strain CPSB21. Additionally, inoculation of CPSB21 enhanced the uptake of Cr 6+ in sunflower plant, while no substantial enhancement was observed on inoculation in tomato plant.

Bioaccumulation and subcellular partitioning of Cr(III) and Cr(VI) in the freshwater green alga Chlamydomonas reinhardtii

Energy Technology Data Exchange (ETDEWEB)

Aharchaou, Imad [Laboratoire Interdisciplinaire des Environnements Continentaux, UMR 7360, Université de Lorraine and CNRS, 8 rue du Général Delestraint, 57070 Metz (France); Rosabal, Maikel; Liu, Fengjie [Institut National de la Recherche Scientifique, Centre Eau Terre Environnement (INRS-ETE), 490 rue de la Couronne, Québec (Québec) G1K 9A9 (Canada); Battaglia, Eric; Vignati, Davide A.L. [Laboratoire Interdisciplinaire des Environnements Continentaux, UMR 7360, Université de Lorraine and CNRS, 8 rue du Général Delestraint, 57070 Metz (France); Fortin, Claude, E-mail: claude.fortin@ete.inrs.ca [Institut National de la Recherche Scientifique, Centre Eau Terre Environnement (INRS-ETE), 490 rue de la Couronne, Québec (Québec) G1K 9A9 (Canada)

2017-01-15

Highlights: • C. reinhardtii accumulated similar levels of Cr(III) and Cr(VI). • The subcellular partitioning of Cr(III) and Cr(VI) was similar. • Cr(III) and Cr(VI) associated mainly with organelles and heat-stable proteins. • Metallomic analysis showed two main Cr-binding biomolecules after 72 h of exposure. - Abstract: Chromium occurs in aquatic environments under two main redox forms, namely Cr(III) and Cr(VI), with different geochemical and biochemical properties. Cr(VI) readily crosses biological membranes of living organisms and once inside the cells it undergoes a rapid reduction to Cr(III). The route of entry for the latter form is, however, poorly known. Using the radioactive tracer {sup 51}Cr we compared the accumulation (absorption and adsorption) of the two Cr forms by the green unicellular alga Chlamydomonas reinhardii after 1 h and 72 h of exposure to 100 nM of either Cr(III) or Cr(VI) at pH 7. Both Cr forms had similar accumulation, with a major part in the extracellular (adsorbed) fraction after 1 h and a major part of total accumulated Cr in the intracellular (absorbed) fraction after 72 h. We also investigated the intracellular partitioning of Cr using an operational fractionation scheme and found that both Cr forms had similar distributions among fractions: Cr was mostly associated with organelles (23 ± 12% after 1 h and 37 ± 7% after 72 h) and cytosolic heat-stable proteins and peptides (39 ± 18% after 1 h and 35 ± 3% after 72 h) fractions. Further investigations using a metallomic approach (SEC-ICP-MS) were performed with the heat-stable proteins and peptides fraction to compare the distribution of the two Cr forms among various biomolecules of this fraction. One Cr-binding biomolecule (∼28 kDa) appeared after 1 h of exposure for both Cr species. After 72 h another biomolecule of lower molecular weight (∼0.7 kDa) was involved in binding Cr and higher signal intensities were observed for Cr(VI) than for Cr(III). We show, for the

Bioaccumulation and subcellular partitioning of Cr(III) and Cr(VI) in the freshwater green alga Chlamydomonas reinhardtii

International Nuclear Information System (INIS)

Aharchaou, Imad; Rosabal, Maikel; Liu, Fengjie; Battaglia, Eric; Vignati, Davide A.L.; Fortin, Claude

2017-01-01

Highlights: • C. reinhardtii accumulated similar levels of Cr(III) and Cr(VI). • The subcellular partitioning of Cr(III) and Cr(VI) was similar. • Cr(III) and Cr(VI) associated mainly with organelles and heat-stable proteins. • Metallomic analysis showed two main Cr-binding biomolecules after 72 h of exposure. - Abstract: Chromium occurs in aquatic environments under two main redox forms, namely Cr(III) and Cr(VI), with different geochemical and biochemical properties. Cr(VI) readily crosses biological membranes of living organisms and once inside the cells it undergoes a rapid reduction to Cr(III). The route of entry for the latter form is, however, poorly known. Using the radioactive tracer "5"1Cr we compared the accumulation (absorption and adsorption) of the two Cr forms by the green unicellular alga Chlamydomonas reinhardii after 1 h and 72 h of exposure to 100 nM of either Cr(III) or Cr(VI) at pH 7. Both Cr forms had similar accumulation, with a major part in the extracellular (adsorbed) fraction after 1 h and a major part of total accumulated Cr in the intracellular (absorbed) fraction after 72 h. We also investigated the intracellular partitioning of Cr using an operational fractionation scheme and found that both Cr forms had similar distributions among fractions: Cr was mostly associated with organelles (23 ± 12% after 1 h and 37 ± 7% after 72 h) and cytosolic heat-stable proteins and peptides (39 ± 18% after 1 h and 35 ± 3% after 72 h) fractions. Further investigations using a metallomic approach (SEC-ICP-MS) were performed with the heat-stable proteins and peptides fraction to compare the distribution of the two Cr forms among various biomolecules of this fraction. One Cr-binding biomolecule (∼28 kDa) appeared after 1 h of exposure for both Cr species. After 72 h another biomolecule of lower molecular weight (∼0.7 kDa) was involved in binding Cr and higher signal intensities were observed for Cr(VI) than for Cr(III). We show, for the

Effect of Heat Treatment on Microstructure and Hardness of Grade 91 Steel

Directory of Open Access Journals (Sweden)

Triratna Shrestha

2015-01-01

Full Text Available Grade 91 steel (modified 9Cr-1Mo steel is considered a prospective material for the Next Generation Nuclear Power Plant for application in reactor pressure vessels at temperatures of up to 650 °C. In this study, heat treatment of Grade 91 steel was performed by normalizing and tempering the steel at various temperatures for different periods of time. Optical microscopy, scanning and transmission electron microscopy in conjunction with microhardness profiles and calorimetric plots were used to understand the microstructural evolution including precipitate structures and were correlated with mechanical behavior of the steel. Thermo-Calc™ calculations were used to support the experimental work. Furthermore, carbon isopleth and temperature dependencies of the volume fraction of different precipitates were constructed.

Gemcitabine and docetaxel in relapsed and unresectable high-grade osteosarcoma and spindle cell sarcoma of bone.

Science.gov (United States)

Palmerini, E; Jones, R L; Marchesi, E; Paioli, A; Cesari, M; Longhi, A; Meazza, C; Coccoli, L; Fagioli, F; Asaftei, S; Grignani, G; Tamburini, A; Pollack, S M; Picci, P; Ferrari, S

2016-04-20

Few new compounds are available for relapsed osteosarcoma. We retrospectively evaluated the activity of gemcitabine (G) plus docetaxel (D) in patients with relapsed high-grade osteosarcoma and high-grade spindle cell sarcoma of bone (HGS). Patients receiving G 900 mg/m(2) d 1, 8; D 75 mg/m(2) d 8, every 21 days were eligible. Primary end-point: progression-free survival (PFS) at 4 months; secondary end-point: overall survival (OS) and response rate. Fifty-one patients were included, with a median age of 17 years (8-71), 26 (51%) were pediatric patients. GD line of treatment: 2nd in 14 patients, ≥3rd in 37. 25 (49%) patients had metastases limited to lungs, 26 (51%) multiple sites. 40 (78%) osteosarcoma, 11 (22%) HGS. Eight (16%) patients achieved surgical complete response (sCR2) after GD. Four-month PFS rate was 46%, and significantly better for patients with ECOG 0 (ECOG 0: 54% vs ECOG 1: 43% vs ECOG 2: 0%; p = 0.003), for patients undergoing metastasectomy after GD (sCR2 75% vs no-sCR2 40 %, p = 0.02) and for osteosarcoma (osteosarcoma 56% vs HGS 18%; p = 0.05), with no differences according to age, line of treatment, and pattern of metastases. Forty-six cases had RECIST measurable disease: 6 (13%) patients had a partial response (PR), 20 (43%) had stable disease (SD) and 20 (43%) had progressive disease (PD). The 1-year OS was 30%: 67% for PR, 54% for SD and 20% for PD (p = 0.005). GD is an active treatment for relapsed high-grade osteosarcoma, especially for ECOG 0 patients, and should be included in the therapeutic armamentarium of metastatic osteosarcoma.

Gemcitabine and docetaxel in relapsed and unresectable high-grade osteosarcoma and spindle cell sarcoma of bone

International Nuclear Information System (INIS)

Palmerini, E.; Jones, R. L.; Marchesi, E.; Paioli, A.; Cesari, M.; Longhi, A.; Meazza, C.; Coccoli, L.; Fagioli, F.; Asaftei, S.; Grignani, G.; Tamburini, A.; Pollack, S. M.; Picci, P.; Ferrari, S.

2016-01-01

Few new compounds are available for relapsed osteosarcoma. We retrospectively evaluated the activity of gemcitabine (G) plus docetaxel (D) in patients with relapsed high-grade osteosarcoma and high-grade spindle cell sarcoma of bone (HGS). Patients receiving G 900 mg/m 2 d 1, 8; D 75 mg/m 2 d 8, every 21 days were eligible. Primary end-point: progression-free survival (PFS) at 4 months; secondary end-point: overall survival (OS) and response rate. Fifty-one patients were included, with a median age of 17 years (8–71), 26 (51 %) were pediatric patients. GD line of treatment: 2nd in 14 patients, ≥3rd in 37. 25 (49 %) patients had metastases limited to lungs, 26 (51 %) multiple sites. Histology: 40 (78 %) osteosarcoma, 11 (22 %) HGS. Eight (16 %) patients achieved surgical complete response (sCR2) after GD. Four-month PFS rate was 46 %, and significantly better for patients with ECOG 0 (ECOG 0: 54 % vs ECOG 1: 43 % vs ECOG 2: 0 %; p = 0.003), for patients undergoing metastasectomy after GD (sCR2 75 % vs no-sCR2 40 %, p = 0.02) and for osteosarcoma (osteosarcoma 56 % vs HGS 18 %; p = 0.05), with no differences according to age, line of treatment, and pattern of metastases. Forty-six cases had RECIST measurable disease: 6 (13 %) patients had a partial response (PR), 20 (43 %) had stable disease (SD) and 20 (43 %) had progressive disease (PD). The 1-year OS was 30 %: 67 % for PR, 54 % for SD and 20 % for PD (p = 0.005). GD is an active treatment for relapsed high-grade osteosarcoma, especially for ECOG 0 patients, and should be included in the therapeutic armamentarium of metastatic osteosarcoma

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 153 ... Issue, Title. Vol 9, No 2 (2006):, Effects of efficient water utilisation on water resources development in Swaziland under climate change, Abstract .... Ethical, Indigenous and Socio-Economic Perspectives, Abstract.

A mechanical and tribological study of Cr/CrN multilayer coatings

Energy Technology Data Exchange (ETDEWEB)

Arias, D.F., E-mail: diegomas@gmail.com [Grupo GEMA, Universidad Católica de Pereira, Pereira (Colombia); Gómez, A. [Laboratório de Fenômenos de Superficie, Escola Politécnica, Universidade de Sao Paulo, Sao Paulo (Brazil); Pontificia Universidad Javeriana Cali (Colombia); Vélez, J.M. [Escuela de Ingeniería de Materiales, Universidad Nacional de Colombia Sede Medellín (Colombia); Souza, R.M. [Laboratório de Fenômenos de Superficie, Escola Politécnica, Universidade de Sao Paulo, Sao Paulo (Brazil); Olaya, J.J. [Departamento de Ingeniería Mecánica y Mecatrónica, Universidad Nacional de Colombia, Bogotá (Colombia)

2015-06-15

Multilayer Cr/CrN coatings with different periodicities were grown on silicon substrates by means of a magnetron sputtering technique. Thin films with only Cr or CrN were also grown, in order to use them as reference samples. Structural, morphological, mechanical and tribological characterization were carried out by using X-ray diffraction (XRD), atomic force microscopy (AFM), nanohardness and nanoscratch techniques, respectively. The characterization results were analyzed as a function of the bilayer thickness (period). In general, the multilayer hardness value increased with the decrease in period. In addition, the validity of the Hall-Petch relationship was confirmed for grain sizes and period values greater than 146 nm and 333 nm, respectively. The coefficient of friction (COF) increased with increasing load, which indicates the contribution of the adhesion to the COF. - Highlights: • Multilayer Cr/CrN coatings with layer thickness between 200 and 1000 nm were grown. • Neither bias voltage not temperature were applied during deposition. • The hardness improves with the increase of the number of bilayers. • The wear rate decreases with the increase of the number of bilayers.

Inscribing Authority: Female Title Bearers in Jewish Inscriptions

Directory of Open Access Journals (Sweden)

Carrie Duncan

2012-02-01

Full Text Available This paper investigates representations of gender in the material culture of the ancient synagogue. The pertinent data are numerous dedicatory and funerary inscriptions linking individual Jews, men and women, with titles seemingly associated with leadership in Late Antique synagogues (ca. 200–600 CE. Bernadette Brooten’s influential 1982 monograph argued against the prevailing tendency to characterize these titles as indications of power, authority, and responsibility when associated with men but as meaningless flattery when applied to women. She suggests that synagogue titles denote power, authority and responsibility on all title bearers equally, both men and women. I question the continued utility of proffering female title-holders as enumerable examples of powerful women rescued from their forgotten place in history. Using theoretical insights developed by historians Elizabeth Clark and Gabrielle Spiegel, this paper will engage a comparative analysis with the work of Riet van Bremen and Saba Mahmood to develop new methods of conceptualizing women’s authority in early Jewish communities. I propose that viewing women’s synagogue titles as culturally constructed representations allows for a fruitful inquiry into how women’s titles were used by male-dominated synagogue communities in their self-articulation and public presentation of Judaism.

Species dependent radiotracer study of Cr(VI) and Cr(III) using an aqueous biphasic system

Energy Technology Data Exchange (ETDEWEB)

Roy, K.; Lahiri, S. [Chemical Sciences Div., Saha Inst. of Nuclear Physics, Kolkata (India)

2008-07-01

The speciation study of Cr(III) and Cr(VI) was carried out using a polyethylene glycol (PEG) based aqueous biphasic extraction system (ABS). Neutron activated Cr(III) and Cr(VI) salts were assayed in a HPGe detector before and after employing aqueous biphasic extraction. Different salts of various salting out abilities were taken as the salt rich phase. The best condition for extraction of Cr(VI) and the maximum differential attitude of ABS to Cr(VI) and Cr(III) was observed when 2 M Na{sub 2}SO{sub 4} and PEG 4000 (50% w/w) solutions were used. Cr(III) can also be extracted by the PEG with prior complexation with diphenylthiocarbazone (dithizone). The chromium dithizonate complex is quantitatively extracted by the PEG rich phase. (orig.)

Migration of Cr-vacancy clusters and interstitial Cr in α-Fe using the dimer method

International Nuclear Information System (INIS)

Chen, D.; Gao, F.; Hu, S. Y.; Sun, X.; Heinisch, H. L.; Henager, C. H.; Khaleel, M. A.; Hu, W. Y.; Terentyev, D.

2010-01-01

The migration mechanisms and the corresponding activation energies of Cr-vacancy (Cr-V) clusters and Cr interstitials in α-Fe have been investigated using the dimer and the nudged elastic-band methods. Dimer searches are employed to find the possible transition states of these defects and the lowest-energy paths are used to determine the energy barriers for migration. A substitutional Cr atom can migrate to a nearest-neighbor vacancy through an energy barrier of 0.56 eV but this simple mechanism alone is unlikely to lead to the long-distance migration of Cr unless there is a supersaturated concentration of vacancies in the system. The Cr-vacancy clusters can lead to long-distance migration of a Cr atom that is accomplished by Fe and Cr atoms successively jumping to nearest-neighbor vacancy positions, defined as a self-vacancy-assisted migration mechanism, with the migration energies ranging from 0.64 to 0.89 eV. In addition, a mixed Cr-Fe dumbbell interstitial can easily migrate through Fe lattices, with the migration energy barrier of 0.17, which is lower than that of the Fe-Fe interstitial. The on-site rotation of the Cr-Fe interstitial and Cr atom hopping from one site to another are believed to comprise the dominant migration mechanism. The calculated binding energies of Cr-V clusters are strongly dependent on the size of clusters and the concentration of Cr atoms in clusters.

31 CFR 505.01 - Short title.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Short title. 505.01 Section 505.01 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE OF FOREIGN... CERTAIN MERCHANDISE BETWEEN FOREIGN COUNTRIES § 505.01 Short title. The regulations in this part may be...

18 CFR 415.1 - Short title.

Science.gov (United States)

2010-04-01

... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Short title. 415.1 Section 415.1 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS-FLOOD PLAIN REGULATIONS Generally § 415.1 Short title. This part shall be known...

Student Achievement in Title I Schools

Science.gov (United States)

Diaz, Abby T.

2017-01-01

This researcher seeks to answer the following question: How did two elementary Title I schools, identified as "high performing" on the first Smarter Balanced assessment, address elements of Maslow's hierarchy of needs when developing school-wide initiatives to enhance student achievement? Many students in Title I schools face barriers to…

P-type Al-doped Cr-deficient CrN thin films for thermoelectrics

Science.gov (United States)

le Febvrier, Arnaud; Van Nong, Ngo; Abadias, Gregory; Eklund, Per

2018-05-01

Thermoelectric properties of chromium nitride (CrN)-based films grown on c-plane sapphire by dc reactive magnetron sputtering were investigated. In this work, aluminum doping was introduced in CrN (degenerate n-type semiconductor) by co-deposition. Under the present deposition conditions, over-stoichiometry in nitrogen (CrN1+δ) rock-salt structure is obtained. A p-type conduction is observed with nitrogen-rich CrN combined with aluminum doping. The Cr0.96Al0.04N1.17 film exhibited a high Seebeck coefficient and a sufficient power factor at 300 °C. These results are a starting point for designing p-type/n-type thermoelectric materials based on chromium nitride films, which are cheap and routinely grown on the industrial scale.

Salt-assisted liquid-liquid microextraction of Cr(VI) ion using an ionic liquid for preconcentration prior to its determination by flame atomic absorption spectrometry

International Nuclear Information System (INIS)

Majidi, B.; Shemirani, F.

2012-01-01

We report on the salt-assisted liquid-liquid microextraction of cationic complexes of Cr(VI) ion using the hydrophilic ionic liquid (IL) 1-butyl-3-methylimidazolium tetrafluoraborate and potassium hydrogen phosphate. This is a novel, simple, non-toxic and effective technique for sample pretreatment technique that displays large extraction efficiency and represents a new platform where Cr(VI) is complexed with 1,5-diphenylcarbazide (DPC) in sulfuric acid medium. It was applied to the extraction of Cr(VI) in the form of the Cr(VI)-DPC complex prior to its determination by flame atomic absorption spectrometry. Cr(III) ion also can be determined by this procedure after oxidation to Cr(VI). Extraction is mainly affected by the amount of water-soluble IL, the kind and quantity of inorganic salts, by pH and the concentration of DPC. Calibration plots are linear in the range from 3 to 150 μg L -1 of Cr(VI), and the limit of detection is 1. 25 μg L -1 . The method was successfully applied to the speciation and determination of trace levels of Cr(III) and Cr(VI) in environmental water samples containing high levels of dissolved salts or food grade salts. (author)

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 183 ... Journal Home > Advanced Search > Browse Title Index ... Vol 61 (2017), New interventions and sustainable solutions: .... Vol 35 (2011), Resurgence of tribal levies: Double taxation for the rural poor, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 901 - 950 of 1355 ... Journal of Applied Sciences and Environmental Management. ... Journal Home > Advanced Search > Browse Title Index .... Vol 22, No 2 (2018), Performance evaluation of a locally fabricated sawdust fired oven for ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 465 ... Journal Home > Advanced Search > Browse Title Index ... and twinning data of an igbo kindred during the Nigerian Civil War, Abstract ... on laboratory estimations with special reference to clinical chemistry, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 533 ... Southern African Linguistics and Applied Language Studies. ... Issue, Title ... Vol 34, No 1 (2016), Book Review: Qualitative-Quantitative Analyses of .... The complex consonants of simple CV-syllables in Zezuru, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 644 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... Ethics review n international health research: quality assurance or bureaucratic nightmare? Details ... Audit of Management of Open Fractures, Details PDF.

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 165 ... Journal Home > Advanced Search > Browse Title Index ... Vol 43 (2011), Assessment of the Learning Commons takeoff at the University of ... the archive of South Africa's Truth and Reconciliation Commission, Abstract.

ER, PgR, Ki67, p27Kip1, and histological grade as predictors of pathological complete response in patients with HER2-positive breast cancer receiving neoadjuvant chemotherapy using taxanes followed by fluorouracil, epirubicin, and cyclophosphamide concomitant with trastuzumab

International Nuclear Information System (INIS)

Kurozumi, Sasagu; Inoue, Kenichi; Takei, Hiroyuki; Matsumoto, Hiroshi; Kurosumi, Masafumi; Horiguchi, Jun; Takeyoshi, Izumi; Oyama, Tetsunari

2015-01-01

Neoadjuvant chemotherapy (NAC) with taxanes followed by fluorouracil, epirubicin, and cyclophosphamide (FEC), and concurrent trastuzumab is a potent regimen for HER2 over-expressing breast cancer. A high pathological complete response (pCR) rate has been achieved using this regimen; however, the predictive factors and prognostic effects of pCR currently remain unclear. In the present study, we determined whether pCR was related to histological grade (HG) and several biological factors including p27 Kip1 . We also assessed the prognosis of the pCR and non-pCR groups, and expected differences between those positive and negative for lymph node metastasis after chemotherapy. A total of 129 Japanese women with HER2-positive invasive breast cancer received either paclitaxel or docetaxel followed by FEC, with the concomitant administration of trastuzumab. The statuses of HG, ER, PgR, Ki67, and p27 Kip1 were evaluated to determine their relationship with pCR. Relapse-free survival (RFS) and overall survival (OS) were also analyzed for their relationship with pCR and pathological nodal involvement. pCR was obtained in 84 out of 129 patients and the pCR rate was 65.1 %. The pCR rates related to 5 factors were as follows: HG (grade 3, 70.0 % vs. grades 1–2, 36.8 %), ER (negative, 78.6 % vs. positive, 40.0 %), PgR (negative, 75.3 % vs. positive, 38.9 %), Ki67 (high, 72.0 % vs. low, 47.2 %), and p27 Kip1 (low, 71.0 % vs. high, 50.0 %). RFS was significantly better in the pCR group than in the non-pCR group (p = 0.018). Patients with remaining nodal disease in the pCR group had worse OS (p = 0.0002). High-HG, low-ER, low-PgR, high-Ki67, and low-p27 Kip1 were identified as predictive factors of pCR in NAC with trastuzumab, while pCR and negative nodes were predictive of better survivals. The online version of this article (doi:10.1186/s12885-015-1641-y) contains supplementary material, which is available to authorized users

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 414 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... of an algebraic function for the permutation of truth table columns, Abstract ... appraisal and productivity levels in selected Nigerian universities, Abstract.

The Effect of Low-Quantity Cr Addition on the Corrosion Behaviour of Dual-Phase High Carbon Steel

Directory of Open Access Journals (Sweden)

Wilson Handoko

2018-03-01

Full Text Available Industrial application of high carbon low alloy steel with the dual-phase structure of martensite and austenite has increased drastically in recent years. Due to its excellent compression strength and its high abrasion resistance, this grade of steel has used as a high performance cutting tool and in press machinery applications. By increasing the usage of more corrosive media in industrial practice and increasing the demand for reducing the production cost, it is crucial to understand the effect of the small addition of Cr on the corrosion behaviour of this grade of steel. In this study, this effect was investigated using Secondary Electron Microscopy (SEM and in-situ Atomic Force Microscopy (AFM in the sodium chloride solution. Also, the corrosion rate was measured using the Tafel polarisation curve. It has been found that the small addition of Cr increased the stability of retained austenite, thus improving its corrosion resistance and reducing its corrosion rate. This effect has been acquired through in-situ high resolution topography images in which the samples were submerged in a corrosive solution. It has been demonstrated that the corrosion rate was reduced when the stability of austenite enhanced.

25 CFR 151.13 - Title examination.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Title examination. 151.13 Section 151.13 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER LAND ACQUISITIONS § 151.13 Title examination. If the Secretary determines that he will approve a request for the acquisition of land from...

Cr 3d surface and bulk states in Sn1-xCrxTe/Cr crystals

International Nuclear Information System (INIS)

Guziewicz, E.; Szamota-Sadowska, K.; Kowalski, B.J.; Grodzicka, E.; Story, T.; Orlowski, B.A.; Johnson, R.L.

1997-01-01

We report a new approach to investigate metal-semiconductor interface formation. Photoemission spectroscopy was applied in order to investigate the clean surface of a Sn 0.97 Cr 0.03 Te crystal and to observe its changes under sequential deposition of small amounts of Cr atoms. In order to analyse the Cr 3d contribution to the valence band, the Fano-type resonance tuned to the Cr 3p-3d transmission was used. The experiment was designed to follow the Sn 0.97 Cr 0.03 Te/Cr interface formation process. At the clean Sn 0.97 Cr 0.03 Te surface, the Cr 3d states contribution to the valence band was found to be positioned 0.8 eV below Fermi level. After the Cr deposition processes the contribution shifted to a higher binding energy and another contribution 5.8 eV below the Fermi level also observed. (author)

Title IX: With New Opportunities, Girls' Interest Rises

Science.gov (United States)

Toporek, Bryan

2012-01-01

On June 23, 1972, President Richard M. Nixon signed into law Title IX of the Education Amendments of 1972, which prohibits gender discrimination in any federally financed education program or activity. Title IX is far-reaching, but the law is most often associated with school and college athletics. Title IX allows schools to prove their athletic…

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 879 ... South African Journal of Higher Education. ... Browse Title Index ... in a USA school setting: Merging transition theory with a narrative approach, Abstract ... Citation analysis of theses and dissertations submitted at the ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 130 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... using the technological pedagogical content knowledge(TPACK) framework, Abstract PDF ... Tamara N. Hrin, Dušica D. Milenković, Mirjana D. Segedinac.

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 278 ... Journal Home > Advanced Search > Browse Title Index ... drie paradigmas beskou: 'n eenheid, of 'n veelheid van perspektiewe? ... Vol 45, No 1 (2011), Genre pedagogy in the mediation of socially-situated literacies ...

Browse Title Index

African Journals Online (AJOL)

Items 251 - 300 of 1260 ... Journal Home > Advanced Search > Browse Title Index ... Consumption of ammonia-nitrogen by aob in immobilized batch culture, Abstract PDF .... Vol 9, No 3S (2017): Special Issue, Design an automatic temperature ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 147 ... Journal Home > Advanced Search > Browse Title Index .... Library (TEEAL) Database among faculty members in Federal University, ... Vol 5, No 2 (2014), Effects of corporate culture on the implementation of automation in ...

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 531 ... Journal Home > Advanced Search > Browse Title Index ... thermal conductivity and viscosity in a flat plate solar collector, Abstract PDF .... similarity method in unsteady two-dimensional MHD boundary layer on the body ...

Role of defects on the electronic and magnetic properties of CrAs, CrSe and CrSb zinc-blende compounds

International Nuclear Information System (INIS)

Galanakis, I.; Pouliasis, S.G.

2009-01-01

We present an extended study of single impurity atoms and atomic swaps in half-metallic CrAs, CrSb and CrSe zinc-blende compounds. Although the perfect alloys present a rather large gap in the minority-spin band, all defects under study, with the exception of void impurities at Cr and sp sites and Cr impurities at sp sites (as long as no swap occurs), induce new states within the gap. The Fermi level can be pinned within these new minority states depending on the lattice constant used for the calculations and the electronegativity of the sp atoms. Although these impurity states are localized in space around the impurity atoms and very fast we regain the bulk behavior, their interaction can lead to wide bands within the gap and thus loss of the half-metallic character

Fracture toughness and sliding properties of magnetron sputtered CrBC and CrBCN coatings

Science.gov (United States)

Wang, Qianzhi; Zhou, Fei; Ma, Qiang; Callisti, Mauro; Polcar, Tomas; Yan, Jiwang

2018-06-01

CrBC and CrBCN coatings with low and high B contents were deposited on 316L steel and Si wafers using an unbalanced magnetron sputtering system. Mechanical properties including hardness (H), elastic modulus (E) and fracture toughness (KIc) as well as residual stresses (σ) were quantified. A clear correlation between structural, mechanical and tribological properties of coatings was found. In particular, structural analyses indicated that N incorporation in CrBC coatings with high B content caused a significant structural evolution of the nanocomposite structure (crystalline grains embedded into an amorphous matrix) from nc-CrB2/(a-CrBx, a-BCx) to nc-CrN/(a-BCx, a-BN). As a result, the hardness of CrBC coating with high B content decreased from 23.4 to 16.3 GPa but the fracture toughness was enhanced. Consequently, less cracks initiated on CrBCN coatings during tribological tests, which combined with the shielding effect of a-BN on wear debris, led to a low friction coefficient and wear rate.

The Analysis of the General Performance and Mechanical Behavior of Unirradiated FeCrAl Alloys Before and After Welding

Energy Technology Data Exchange (ETDEWEB)

Gussev, Maxim N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Field, Kevin G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yamamoto, Yukinori [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-06-03

The present report summarizes and discusses the preliminary results for the in-depth characterization of the modern, nuclear-grade FeCrAl alloys currently under development. The alloys were designed for enhanced radiation tolerance and weldability, and the research is currently being pursued by the Department of Energy (DOE) Nuclear Energy Enabling Technologies (NEET) program. Last year, seven candidate FeCrAl alloys with well-controlled chemistry and microstructures were designed and produced; welding was performed under well-controlled conditions. The structure and general performance of unirradiated alloys were assessed using standardized and advanced microstructural characterization techniques and mechanical testing. The primary objective is to identify the best candidate alloy, or at a minimum to identify the contributing factors that increase the weldability and radiation tolerance of FeCrAl alloys, therefore enabling future generations of FeCrAl alloys to deliver better performance parameters. This report is structured so as to describe these critical assessments of the weldability; radiation tolerance will be reported on in later reports from this program.

Browse Title Index

African Journals Online (AJOL)

Items 601 - 650 of 879 ... South African Journal of Higher Education. ... Browse Title Index .... The challenge of thesis supervision in an art university, Abstract ... No 2 (2004), Robert Sternberg's mental self-government theory and its contribution to ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 736 ... Journal Home > Advanced Search > Browse Title Index ... Vol 5 (2008), A Contagious Malady: The Human Quest for Truth through Religion, Abstract ... A Study of Politeness Strategies Used by the National University of ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 879 ... Journal Home > Advanced Search > Browse Title Index ... Vol 20, No 4 (2006), Assessing academic potential for university admission: ... Vol 16, No 2 (2002), Book Review: Rethinking truth by Higgs, P & Smith, J, Details.

Browse Title Index

African Journals Online (AJOL)

Items 651 - 700 of 1199 ... Issue, Title ... Vol 5, No 1 (2011), Motivation, an Essential Ingredient for Optimal Performance in Emerging Markets, Abstract PDF ... Vol 3, No 5 (2009), Multinational transfer pricing and international taxation: what, why, ...

Browse Title Index

African Journals Online (AJOL)

Items 451 - 500 of 533 ... Journal Home > Advanced Search > Browse Title Index .... for past tense forms in Northern Sotho: verb stems with final 'm' and 'n', Abstract ... in an academic writing class: Implications for a dialogic pedagogy, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 701 - 750 of 808 ... Issue, Title ... Vol 58, No 2 (2010), Short Communicaton: The socio-economic impact of helminth infections and the ... Vol 62 (2014): Special Edition, Special edition summarizing the scientific discourse which took place ...

The Reduction of Cr(VI) to Cr(III) by Natural Fe-Bearing Minerals: A Synchrotron XAS Study

Science.gov (United States)

Xu, H.; Guo, X.; Ding, M.; Migdissov, A. A.; Boukhalfa, H.; Sun, C.; Roback, R. C.; Reimus, P. W.; Katzman, D.

2017-12-01

Cr(VI) in the form of CrO42- is a pollutant species in groundwater and soils that can pose health and environmental problems. Cr(VI) associated with use as a corrosion inhibitor at a power plant from 1956-1972 is present in a deep groundwater aquifer at Los Alamos National Laboratory. A potential remediation strategy for the Cr contamination is reduction of Cr(VI) to Cr(III) via the acceptance of electrons from naturally occurring or induced Fe(II) occurring in Fe-bearing minerals. In this work, using synchrotron-based X-ray techniques, we investigated the Cr reduction behavior by Fe-bearing minerals from outcrop and core samples representative of the contaminated portion of the aquifer. Samples were exposed to solutions with a range of known Cr (VI) concentrations. XANES and EXAFS spectra showed that all the Cr(VI) had been reduced to Cr(III), and micro XRF mapping revealed close correlation of Cr and Fe distribution, implying that Fe(II) in minerals reduced Cr(VI) in the solution. Similar behavior was observed from in-situ XANES measurements on Cr reduction and adsorption by mineral separates from the rock samples in Cr(VI)-bearing solutions. In addition, to obtain reference parameters for interpreting the data of natural samples, we collected Cr and Fe EXAFS spectra of Cr(III)-Fe(III) hydroxide solid solutions, which show progressive changes in the local structure around Cr and Fe over the whole series.

Browse Title Index

African Journals Online (AJOL)

Items 301 - 350 of 788 ... Journal Home > Advanced Search > Browse Title Index ... Vol 26, No 1 (2018), Gender differentials in the perception of .... Vol 25, No 1 (2017), Impact of total quality management on students' academic performance in ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 194 ... Journal Home > Advanced Search > Browse Title Index ... Vol 14, No 1 (2000), A functional categoriality of adjectives in ... Vol 1, No 1 (1987), Alienation and affirmation: The humanistic vision of Bessie Head, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 1117 ... Journal Home > Advanced Search > Browse Title Index ... Vol 13, No 3 (2007):, an edu-ethical perspecitve on the nature of truth: case studies in elite ... 2009: September: Supplement, An empirical study of university ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 294 ... Journal Home > Advanced Search > Browse Title Index. Log in or .... S Edwards, M Hlongwane, J Thwala, N Robinson ... Vol 16, No 1 (2017), Infancy of internet cafe: The substitute of ubuntu-padare pedagogy, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 98 ... Journal Home > Advanced Search > Browse Title Index ... model for the continued professionalisation of student affairs in Africa, Abstract PDF ... Vol 2, No 2 (2014), Book Review: How College Affects Students, A Third decade ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 76 ... Journal Home > Advanced Search > Browse Title Index ... Vol 4, No 1 (2011), Automation of AutoCAD for Detailing of Reinforced .... Vol 10, No 1 (2017), Housing data base for sustainable housing provision, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 103 ... Issue, Title ... SE Edusah, E Osei-Tutu ... Vol 6, No 2 (2016), Interrelationships among unemployment, inflation and economic growth in Nigeria, Abstract .... Vol 4, No 3 (2014): Special Edition, Socio-cultural Issues for ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 41 of 41 ... Issue, Title ... Vol 1, No 3 (2004): Special Edition, Assessment of the quality and reserves of Bat ... Vol 1, No 1 (1997), Bovine dermatophilosis in Zambia: epidemiology, socio-economic impacts and future perspectives, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 351 - 391 of 391 ... Issue, Title ... Vol 2, No 3 (1999): Special Edition, The efficacy of low volume application of roundup ... Vol 1, No 1 (1998), The relationships among National Socio-Economic Indicators and Child Health Statistics, Abstract.

LaCrO{sub 3}-dispersed Cr for metallic interconnect of planar SOFC

Energy Technology Data Exchange (ETDEWEB)

Song, Rak-Hyun; Shin, Dong Ryul [Korea Institute of Energy Research, Taejon (Korea, Republic of); Dokiya, Masayuki [National Institute of Materials and Chemical Research, Ibaraki (Japan)

1996-12-31

In the planar SOFC, the interconnect materials plays two roles as an electrical connection and as a gas separation plate in a cell stack. The interconnect materials must be chemically stable in reducing and oxidizing environments, and have high electronic conductivity, high thermal conductivity, matching thermal expansion with an electrolyte, high mechanical strength, good fabricability, and gas tightness. Lanthanum chromite so far has been mainly used as interconnect materials in planar SOFC. However, the ceramic materials are very weak in mechanical strength and have poor machining property as compared with metal. Also the metallic materials have high electronic conductivity and high thermal conductivity. Recently some researchers have studied metallic interconnects such as Al{sub 2}O{sub 3}/Inconel 600 cermet, Ni-20Cr coated with (LaSr)CoO{sub 3}, and Y{sub 2}O{sub 3-} or La{sub 2}O{sub 3}-dispersed Cr alloy. These alloys have still some problems because Ni-based alloys have high thermal expansion, the added Al{sub 2}O{sub 3}, Y{sub 2}O{sub 3} and La{sub 2}O{sub 3} to metals have no electronic conductivity, and the oxide formed on the surface of Cr alloy has high volatility. To solve these problems, in this study, LaCrO{sub 3}-dispersed Cr for metallic interconnect of planar SOFC was investigated. The LaCrO{sub 3}-dispersed Cr can be one candidate of metallic interconnect because LaCrO{sub 3} possesses electronic conductivity and Cr metal has relatively low thermal expansion. The content of 25 vol.% LaCrO{sub 3} Was selected on the basis of a theoretically calculated thermal expansion. The thermal expansion, electrical and oxidation properties were examined and the results were discussed as related to SOFC requirements.

PLASTIC DEFORMATION ON THE MACHINED SURFACE OF STEEL Cr20Ni10MoTi AT DRILLING

Directory of Open Access Journals (Sweden)

Jozef Jurko

2009-07-01

Full Text Available Information about material machinability is very important for the machining technology. Precise and reliable information on the machinability of a material before it enters the machining process is a necessity, and this brings the verification of technological methods in practice. This article presents the conclusions of machinability tests on austenitic stainless steel according to EN-EU (ISO: steel Cr20Ni10MoTi. This article presents the conclusions of VEGA grant agency at the Ministry of Education SR for supporting research work and co-financing the projects: Grant work #01/3173/2006 with the title „Experimental investigation of cutting zones in drilled and milled stainless steels

Browse Title Index

African Journals Online (AJOL)

Items 151 - 167 of 167 ... Issue, Title ... Vol 2, No 2 (2013), Women and the Leadership Paradigm: Bridging the Workplace Gender-Gap in Nigeria, Abstract PDF ... Vol 5, No 2 (2016), Women's participation and gender issues in local governance ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 73 of 73 ... Journal Home > Advanced Search > Browse Title Index ... Vol 13 (2006), The ageing eye” functional changes from cradle to gray: A ... Vol 12 (2005), The evaluation of vision in children using monocular vision acuity and ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 391 ... Journal Home > Advanced Search > Browse Title Index ... Efficacy of four Rodenticides on the Ghanaian Market, Abstract ... Vol 2, No 1 (2000):, Determination of some wear elements in used car engine oil and oil filter ...

Browse Title Index

African Journals Online (AJOL)

Items 251 - 300 of 652 ... Journal Home > Advanced Search > Browse Title Index ... Vol 18, No 7 (2015), Introduction to virtual property: Lex virtualis ipsa ... Vol 17, No 1 (2014), Legal challenges relating to the commercial use of outer space, with ...

Browse Title Index

African Journals Online (AJOL)

Items 551 - 600 of 879 ... Journal Home > Advanced Search > Browse Title Index ... A James, E Ralfe, L van Laren, N Ngcobo ... 1 (2011), Recognition of prior learning in promoting lifelong learning: A pedagogy of hope or a shattering of dreams?

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 89 ... Issue, Title ... of two-phased approaches to load balancing in cloud computing, Abstract ... Vol 19, No 1 (2012), Assessing Network Services and Security in ... Vol 23, No 1 (2016), Cloud model construct for transaction-based ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 198 ... Issue, Title ... Vol 13, No 1 (2015), Biometric Enhancement of Home and Office Security to Reduce Assassinations in Nigeria, Abstract PDF ... Vol 9, No 1 (2013), Cloud Computing: Key to IT Development in West Africa ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 198 of 198 ... Issue, Title ... scheme for QoS and energy conservation in cloud computing, Abstract PDF ... Vol 9, No 1 (2013), Performance and Security Evaluation of ... Vol 18, No 1 (2017), Reducing capital flight through local cloud ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 97 of 97 ... Journal Home > Advanced Search > Browse Title Index ... Vol 20, No 2 (2008), Research Note: Anthropometric data of the foot of ... Vol 26, No 1 (2014), Validation of the Automation Attitude Questionnaire for Airline Pilots ...

Titles of Midas

Directory of Open Access Journals (Sweden)

G. L. Huxley

2001-09-01

Full Text Available The Phrygian inscription on the tomb at Yazılıkaya (8th century gives Midas the titles wanax and lawagtas, paralled in Mycenaean, and there were strong connections between his dynasty and Greek Aeolis.

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 412 ... Issue, Title. Vol 30, No 3 (2011) ... Transferring the principle of double effect from war to business, Abstract. G. J. Rossouw ... Vol 22, No 2 (2003), Can more business ethics teaching halt corruption in companies? Abstract.

Phase I trial of the androgen receptor modulator CR1447 in breast cancer patients

Directory of Open Access Journals (Sweden)

Martin Zweifel

2017-09-01

Full Text Available CR1447 (4-hydroxytestosterone, 4-OHT binds to the androgen receptor and has antiproliferative activity in both ER-positive and ER-negative/AR-positive breast cancer cells in preclinical studies. The objective of this first-in man trial was to evaluate the safety and to determine the dose of CR1447, administered as an ointment, for Phase II. Escalating doses (100, 200, 400 mg of CR1447 were administered topically on a daily basis to patients with ER-positive/AR-positive/HER2-negative advanced breast cancer pretreated with several lines of therapy. 14 patients have been treated for a total of 42 cycles. Two patients, one at dose level 100 mg and one at dose level 200 mg, showed early tumour progression and were replaced. Related adverse events were all ≤ grade 2 and included fatigue, bone and joint pain, stiffness, dry skin and mouth, nausea, sweating, urinary tract infection, rash, headache and distress. No drug-related dose-limiting toxicities (DLTs were seen. Two patients (17% achieved stable disease at 3 months. Pharmacokinetic analysis confirmed dose-dependent transdermal uptake of CR1447. 4-OH-androstenedione (4-OHA, a key metabolite of 4-OHT, was undetectable in most of the plasma samples. Urine metabolites of 4-OHT and 4-OHA indicate high exposure of 4-OHT after topical administration. Oestradiol serum concentrations did not increase, confirming preclinical data that CR1447 is not converted to estrogens in vivo. In conclusion, CR1447 administered transdermally as an ointment is well tolerated and appears to have single-agent activity in heavily pretreated ER-positive/HER2-negative breast cancer patients. The recommended phase II dose is 400 mg/day.

Plantago lanceolata growth and Cr uptake after mycorrhizal inoculation in a Cr amended substrate

Directory of Open Access Journals (Sweden)

Amaia Nogales

2012-03-01

Full Text Available Arbuscular mycorrhizal fungi from two chromium contaminated sites, one with 275 mg kg-1 of Cr (zone A and the other with 550 mg kg-1 Cr (zone B, were multiplied and tentatively identified. The effect of both fungal consortia on Plantago lanceolata plant growth in a substrate amended with 200 mg kg-1 of Cr and with 400 mg kg-1 Cr was assessed and compared with the growth of plants inoculated with Glomus intraradices BEG72. Only the plants inoculated with G. intraradices BEG72 and with the fungal consortia obtained from the area with a high Cr contamination (zone B grew in the soil with 400 mg kg-1 of Cr. The consortia of fungi from zone B, decreased the plant’s uptake/translocation of the heavy metal compared with G. intraradices BEG72. These results underscore the differential effect of AM fungi in conferring bioprotection in Cr contaminated soils.

Effect of Cr4+ impurities in Nd:Cr:GSGG and Nd:Cr:YAG laser materials on parameters of lasers at solar pumping

International Nuclear Information System (INIS)

Payziyev, Sh.D.; Bakhramov, S.A.; Shayimov, F.F.; Fayziev, A.Sh.

2015-01-01

The analysis of an effect of Cr 4+ impurity ions, existent in Nd 3+ :Cr 3+ :GSGG and Nd 3+ :Cr 3+ :YAG laser materials on output parameters of solar pumped lasers is carried out by modeling of lasing process at solar pumping. (authors)

Selected characteristic of silumins with additives of Ni, Cu, Cr, Mo, W and V

Directory of Open Access Journals (Sweden)

S. Pietrowski

2010-04-01

Full Text Available The study, presents an investigation results of new grades of silumins containing of: 7,0÷17,0% Si, 4,0% Ni, 4,0% Cu and 0,5% Cr, Mo, W each as well as V. The influence tests were carried out of - antimony addition, strontium and phosphorus modification, supersaturation and ageing processes - on microstructure and silumins hardness. Revealed that investigated silumins, depending on the state, are characte-rized by hardness in the range of 80÷180 HB.

Corrosion Study of Super Ferritic Stainless Steel UNS S44660 (26Cr-3Ni-3Mo) and Several Other Stainless Steel Grades (UNS S31603, S32101, and S32205) in Caustic Solution Containing Sodium Sulfide

Science.gov (United States)

Chasse, Kevin R.; Singh, Preet M.

2013-11-01

Electrochemical techniques, scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) were used in this study to show how the corrosion mechanism of several commercial grades of stainless steel in hot caustic solution is strongly influenced by the presence of sodium sulfide. Experimental results from super ferritic stainless steel UNS S44660 (26Cr-3Ni-3Mo) were compared to austenitic stainless steel UNS S31603, lean duplex stainless steel (DSS) UNS S32101, and standard DSS UNS S32205 in caustic solution, with and without sodium sulfide, at 443 K (170 °C). Weight loss measurements indicated that corrosion rates of UNS44660 were much lower than the other grades of stainless steel in the presence of the sodium sulfide. Potentiodynamic polarization and linear polarization resistance measurements showed that the electrochemical behavior was altered by the adhesion of sulfur species, which reduced the polarization resistances and increased the anodic current densities. SEM and XPS results imply that the surface films that formed in caustic solution containing sodium sulfide were defective due to the adsorption of sulfide, which destabilized the passive film and led to the formation of insoluble metal sulfide compounds.

Sintering behaviour and mechanical properties of Cr3C2–NiCr ...

Indian Academy of Sciences (India)

fracture toughness. Keywords. Cermet; Cr3C2–NiCr; sintering; mechanical properties. ... et al investigated the mechanical properties of VC, Cr3C2 and NbC doped ..... Huang S G, Li L, Van der Biest O and Vleugels J 2008 J. Alloys. Compds.

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 1732 ... Journal Home > Advanced Search > Browse Title Index ... Vol 10, No 3 (2007), An Audit Of Perioperative Cardiac Arrest At ... Vol 11, No 4 (2008), An Audit Of Rejected Repeated X-ray Films As A Quality Assurance ...

Distribution of chromium species in a Cr-polluted soil: presence of Cr(III) in glomalin related protein fraction.

Science.gov (United States)

Gil-Cardeza, María L; Ferri, Alejandro; Cornejo, Pablo; Gomez, Elena

2014-09-15

The accumulation of Cr in soil could be highly toxic to human health; therefore Cr soil distribution was studied in rhizosphere soils from Ricinus communis and Conium maculatum and bare soil (BS) from an industrial and urban area in Argentina. Total Cr, Cr(VI) and Cr(III) concentrations were determined in 3 soil fractions: total, extractable and associated to total-glomalin-related protein (T-GRSP). BS had the highest total Cr and total Cr(VI) concentrations. Total Cr(VI) concentration from both rhizosphere soils did not differ from the allowed value for residential area in Argentina (8 μg Cr(VI) g(-1) soil), while total Cr(VI) in BS was 1.8 times higher. Total Cr concentration in all the soils was higher than the allowed value (250 μg Cr g(-1) soil). Extractable and associated to T-GRSP Cr(VI) concentrations were below the detection limit. Cr(III) bound to T-GRSP was the highest in the BS. These findings are in agreement with a long term effect of glomalin in sequestrating Cr. In both plant species, total Cr was higher in root than in shoot and both species presented arbuscular mycorrhizal fungi (AMF). As far as we know, this is the first study that reports the presence of Cr in T-GRSP fraction of soil organic matter. These findings suggest that Cr mycorrhizostabilization could be a predominant mechanism used by R. communis and C. maculatum to diminish Cr soil concentration. Nevertheless, further research is needed to clarify the contribution of native AMF isolated from R. communis and C. maculatum rhizosphere to the Cr phytoremediation process. Copyright © 2014 Elsevier B.V. All rights reserved.

Black Cr/α-Cr2O3 nanoparticles based solar absorbers

International Nuclear Information System (INIS)

Khamlich, S.; Nemraoui, O.; Mongwaketsi, N.; McCrindle, R.; Cingo, N.; Maaza, M.

2012-01-01

Monodisperse spherical core–shell particles of Cr/α-Cr 2 O 3 with high adhesion were successfully coated on rough copper substrates by a simple self-assembly-like method for the use in solar thermal absorbers. The structure and morphology of the core-shell particles of Cr/α-Cr 2 O 3 were effectively controlled by deposition temperature and the pH of the initial precursor solution. Their characterizations were carried out with X-ray diffraction, scanning electron microscopy, energy dispersive spectrometry and attenuated total reflection, as well as UV–vis diffuse reflectance spectroscopy. The samples aged for more than 40 h at 75 °C exhibit the targeted high absorbing optical characteristic “Black chrome” while those aged for ≤40 h show a significant high UV–vis diffuse reflectance “green color”.

Estimation of the Temperature-Dependent Nitrogen Solubility in Stainless Fe-Cr-Mn-Ni-Si-C Steel Melts During Processing

Science.gov (United States)

Wendler, Marco; Hauser, Michael; Sandig, Eckhard Frank; Volkova, Olena

2018-04-01

The influence of chemical composition, temperature, and pressure on the nitrogen solubility of various high alloy stainless steel grades, namely Fe-14Cr-(0.17-7.77)Mn-6Ni-0.5Si-0.03C [wt pct], Fe-15Cr-3Mn-4Ni-0.5Si-0.1C [wt pct], and Fe-19Cr-3Mn-4Ni-0.5Si-0.15C [wt pct], was studied in the melt. The temperature-dependent N-solubility was determined using an empirical approach proposed by Wada and Pehlke. The thus calculated N-concentrations overestimate the actual N-solubility of all the studied Fe-Cr-Mn-Ni-Si-C steel melts at a given temperature and pressure. Consequently, the calculation model has to be modified by Si and C because both elements are not recognized in the original equation. The addition of the 1st and 2nd order interaction parameters for Si and C to the model by Wada and Pehlke allows a precise estimation of the temperature-dependent nitrogen solubility in the liquid steel bath, and fits very well with the measured nitrogen concentrations during processing of the steels. Moreover, the N-solubility enhancing effect of Cr- and Mn-additions has been demonstrated.

Overview of 9Cr steels properties for structural application in sodium fast reactors

International Nuclear Information System (INIS)

Cabet, Celine; Courouau, Jean-Louis; Dalle, France; Desgranges, Clara; Forest, Laurent; Martinelli, Laure; Sauzay, Maxime

2015-01-01

A research and development programme has been launched by CEA, EDF and AREVA for the choice and qualification of material for sodium fast reactor (SFR) structural components. The requirements on steam generator (SG) are demanding, with operating temperatures ranging from 240 deg. C to 530 deg. C in water/steam and in sodium for an extended design life of several decades. The selection of the SG materials is based on many characteristics: fabrication, welding, thermal properties, mechanical strength at low and high temperature, environmental resistance. 9%Cr steels which are relevant candidate alloys for different designs of SGs have been extensively studied in the past decade. The objective of this paper is to review some advances made at CEA on determining properties of the X10CrMoVNb9-1 steel (hereafter named 'grade 91'): welding, modelling of cyclic softening, modelling of long-term creep, compatibility with liquid sodium, corrosion in steam. (authors)

Isotope Effects in the Bonds of beta-CrOOH and beta-CrOOD

DEFF Research Database (Denmark)

Nørlund Christensen, A.; Hansen, P.; Lehmann, M. S.

1976-01-01

Samples of orthorhombic chromium oxide hydroxide, beta -CrOOH, and the deuterated compound, beta -CrOOD, were prepared hydrothermally. The crystal structures were determined by powder profile refinement technique using neutron diffraction data. Unit cells are: beta -CrOOH: a equals 4. 862(2) A, b...... equals 4. 298(a) A, c equals 2. 995(1) A; beta -CrOOD: a equals 4. 873(5) A, b equals 4. 332(7) A, c equals 2. 963(2) A, with Z equals 2. The space group is P2//1nm or Pnnm....

Density of Liquid Ni-Cr Alloy

Institute of Scientific and Technical Information of China (English)

无

2003-01-01

The density of liquid Ni-Cr alloy was measured by a modified sessile drop method. The density of liquid Ni-Cr alloywas found to decrease with increasing temperature and Cr concentration in the alloy. The molar volume of liquidNi-Cr alloy increases with increasing the Cr concentration in the alloy. The molar volume of Ni-Cr alloy determinedin the present work shows a positive deviation from the linear molar volume.

Land Titles and Rice Production in Vietnam

DEFF Research Database (Denmark)

Van Den Broeck, Katleen; Newman, Carol; Tarp, Finn

analysis of plot level rice yields that land titles are indeed important. Only exclusively held titles have the expected positive effects, and the positive effect on yields is found in male headed households. Furthermore, a household level rice yield function reveals that exclusive user rights...

Analysis of PTA hardfacing with CoCrWC and CoCrMoSi alloys

Directory of Open Access Journals (Sweden)

Adriano Scheid

2013-12-01

Full Text Available CoCrWC alloys are widely used to protect components that operate under wear and high temperature environments. Enhanced performance has been achieved with the CoCrMoSi alloys but processing this alloy system is still a challenge due to the presence of the brittle Laves phase, particularly when welding is involved. This work evaluated Plasma Transferred Arc coatings processed with the Co-based alloy CoMoCrSi - Tribaloy T400, reinforced with Laves phase, comparing its weldability to the CoCrWC - Stellite 6, reinforced with carbides. Coatings were also analyzed regarding the response to temperature exposure at 600°C for 7 days and subsequent effect on microstructure and sliding abrasive wear. Coatings characterization was carried out by light and scanning electron microscopy, X-ray diffraction and Vickers hardness. CoCrWC coatings exhibited a Cobalt solid solution dendritic microstructure and a thin interdendritic region with eutectic carbides, while CoCrMoSi deposits exhibit a large lamellar eutectic region of Laves phase and Cobalt solid solution and a small fraction of primary Laves phase. Although phase stability was observed by X-ray diffraction, coarsening of the microstructure occurred for both alloys. CoCrMoSi showed thicker lamellar Laves phase and CoCrWC coarser eutectic carbides. Coatings stability assessed by wear tests revealed that although the wear rate of the as-deposited CoCrMoSi alloy was lower than that of CoCrWC alloy its increase after temperature exposure was more significant, 22% against 15%. Results were discussed regarding the protection of industrial components in particular, bearings in 55AlZn hot dip galvanizing components.

Femtosecond Cr:LiSAF and Cr:LiCAF lasers pumped by tapered diode lasers.

Science.gov (United States)

Demirbas, Umit; Schmalz, Michael; Sumpf, Bernd; Erbert, Götz; Petrich, Gale S; Kolodziejski, Leslie A; Fujimoto, James G; Kärtner, Franz X; Leitenstorfer, Alfred

2011-10-10

We report compact, low-cost and efficient Cr:Colquiriite lasers that are pumped by high brightness tapered laser diodes. The tapered laser diodes provided 1 to 1.2 W of output power around 675 nm, at an electrical-to-optical conversion efficiency of about 30%. Using a single tapered diode laser as the pump source, we have demonstrated output powers of 500 mW and 410 mW together with slope efficiencies of 47% and 41% from continuous wave (cw) Cr:LiSAF and Cr:LiCAF lasers, respectively. In cw mode-locked operation, sub-100-fs pulse trains with average power between 200 mW and 250 mW were obtained at repetition rates around 100 MHz. Upon pumping the Cr:Colquiriite lasers with two tapered laser diodes (one from each side of the crystal), we have observed scaling of cw powers to 850 mW in Cr:LiSAF and to 650 mW in Cr:LiCAF. From the double side pumped Cr:LiCAF laser, we have also obtained ~220 fs long pulses with 5.4 nJ of pulse energy at 77 MHz repetition rate. These are the highest energy levels reported from Cr:Colquiriite so far at these repetition rates. Our findings indicate that tapered diodes in the red spectral region are likely to become the standard pump source for Cr:Colquiriite lasers in the near future. Moreover, the simplified pumping scheme might facilitate efficient commercialization of Cr:Colquiriite systems, bearing the potential to significantly boost applications of cw and femtosecond lasers in this spectral region (750-1000 nm).

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 1020 ... Issue, Title ... Vol 48, No 2 (2006), Barriers to HIV Care and Treatment by Doctors: A review of the literature. ... Vol 48, No 5 (2006), Breast cancer – early detection and screening in South African women from the ...

Microstructure and Mechanical Characterization of a Dissimilar Friction-Stir-Welded CuCrZr/CuNiCrSi Butt Joint

Directory of Open Access Journals (Sweden)

Youqing Sun

2018-05-01

Full Text Available Dissimilar CuNiCrSi and CuCrZr butt joints were successfully frictionstirwelded at constant welding speed of 150 mm/min and rotational speed of 1400 rpm with the CuCrZr alloy or the CuNiCrSi alloy located on the advancing side (AS. The microstructure and mechanical properties of joints were investigated. When the CuCrZr alloy was located on the AS, the area of retreating material in the nugget zone was a little bigger. The Cr solute-rich particles were found in the nugget zone on CuCrZr side (CuCrZr-NZ while a larger density of solute-rich particles identified as the concentration of Cr and Si element was found in the nugget zone on CuNiCrSi side (CuNiCrSi-NZ. The Cr precipitates and δ-Ni2Si precipitates were found in the base metal on CuNiCrSi side (CuNiCrSi-BM but only Cr precipitates can be observed in the base metal on CuCrZr side (CuCrZr-BM. Precipitates were totally dissolved into Cu matrix in both CuCrZr-NZ and CuNiCrSi-NZ, which led to a sharp decrease in both micro-hardness and tensile strength from BM to NZ. When the CuNiCrSi was located on the AS, the tensile testing results showed the fracture occurred at the CuCrZr-NZ, while the fracture was found at the mixed zone of CuNiCrSi-NZ and CuCrZr-NZ for the other case.

Construction of long-term isochronous stress-strain curves by a modeling of short-term creep curves for a Grade 9Cr-1Mo steel

International Nuclear Information System (INIS)

Kim, Woo-Gon; Yin, Song-Nan; Koo, Gyeong-Hoi

2009-01-01

This study dealt with the construction of long-term isochronous stress-strain curves (ISSC) by a modeling of short-term creep curves for a Grade 9Cr-1Mo steel (G91) which is a candidate material for structural applications in the next generation nuclear reactors as well as in fusion reactors. To do this, tensile material data used in the inelastic constitutive equations was obtained by tensile tests at 550degC. Creep curves were obtained by a series of creep tests with different stress levels of 300MPa to 220MPa at an identical controlled temperature of 550degC. On the basis of these experimental data, the creep curves were characterized by Garofalo's creep model. Three parameters of P 1 , P 2 and P 3 in Garofalo's model were properly optimized by a nonlinear least square fitting (NLSF) analysis. The stress dependency of the three parameters was found to be a linear relationship. But, the P 3 parameter representing the steady state creep rate exhibited a two slope behavior with different stress exponents at a transient stress of about 250 MPa. The long-term creep curves of the G91 steel was modeled by Garofalo's model with only a few short-term creep data. Using the modeled creep curves, the long-term isochronous curves up to 10 5 hours were successfully constructed. (author)

53Cr NMR study of CuCrO2 multiferroic

Science.gov (United States)

Smol'nikov, A. G.; Ogloblichev, V. V.; Verkhovskii, S. V.; Mikhalev, K. N.; Yakubovskii, A. Yu.; Kumagai, K.; Furukawa, Y.; Sadykov, A. F.; Piskunov, Yu. V.; Gerashchenko, A. P.; Barilo, S. N.; Shiryaev, S. V.

2015-11-01

The magnetically ordered phase of the CuCrO2 single crystal has been studied by the nuclear magnetic resonance (NMR) method on 53Cr nuclei in the absence of an external magnetic field. The 53Cr NMR spectrum is observed in the frequency range νres = 61-66 MHz. The shape of the spectrum depends on the delay tdel between pulses in the pulse sequence τπ/2- t del-τπ- t del-echo. The spin-spin and spin-lattice relaxation times have been measured. Components of the electric field gradient, hyperfine fields, and the magnetic moment on chromium atoms have been estimated.

Heterogeneity of Cr in Mytilus edulis: Implications for the Cr isotope system as a paleo-redox proxy

Science.gov (United States)

Bruggmann, Sylvie; Klaebe, Robert; Frei, Robert

2017-04-01

Changes in 53Cr/52Cr (δ53Cr) values recorded by biogenic carbonates are emerging as a proxy for variations in the redox state of the Earth's oceans and atmosphere (e.g. [1], [2]). We investigate the ability of modern carbonate shells (Mytilus edulis) to record the δ53Cr composition of ambient seawater in order to assess their utility as a paleo-redox proxy. Samples of cultivated M. edulis from the Kiel Fjord, Germany, were analyzed for their δ53Cr composition and Cr concentrations [Cr] using TIMS. To disentangle the pathway of Cr into the carbonate shell, a series of step-digestions of their organic outer sheaths (periostraca) and their intra-layer composition were performed. Bulk analyses of specimens with intact periostraca returned 16 to 34 ppb Cr with δ53Cr values ranging from 0.28 to 0.65 ± 0.1 (2SE) and thus fall within the range of surface seawater from the Baltic Sea (0.3 - 0.6 \\permil [3]). Partial removal of periostraca resulted in lower [Cr] (5 to 17 ppb) and δ53Cr values (-0.05 ± 0.15 \\permil). These results show a positive correlation between the amount of organic matter present in a sample and both [Cr] and δ53Cr (n = 9). With nearly complete removal of periostraca, the remaining [Cr] is significantly lower (less than 5 ppb) and can only be accessed by incineration of the carbonate shell. The correlation between [Cr], δ53Cr and the amount of periostracum present in bulk samples indicates that a significant proportion of preserved Cr may be associated with the organic outer sheath. The Cr endmember accessed after incineration is less likely associated with the carbonate crystal lattice. Instead, the δ53Cr values obtained after incineration are similar to those reported from terrestrial rocks, suggesting the influence of detrital particles. Alternatively, Cr may be reduced and subsequently re-oxidized during the mineralization of biogenic carbonates [4]. Seasonal changes in primary productivity in seawater may further influence the shell

Exploring New Directions: Title I in the Year 2000.

Science.gov (United States)

Puma, Michael J.; Drury, Darrel W.

This report takes stock of the present Title I program, identifies the most promising approaches to educating the nation's disadvantaged children, and offers guidance to policymakers seeking to improve Title I's effectiveness. The report draws upon hundreds of studies, evaluations, and other documents, and details the evolution of the Title I…

24 CFR 232.595 - Eligibility of title.

Science.gov (United States)

2010-04-01

... URBAN DEVELOPMENT MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES MORTGAGE INSURANCE FOR NURSING HOMES, INTERMEDIATE CARE FACILITIES, BOARD AND CARE HOMES, AND ASSISTED... Fire Safety Equipment Title § 232.595 Eligibility of title. In order for the property which is to be...

Kinetic stable Cr isotopic fractionation between aqueous Cr(III)-Cl-H2O complexes at 25 °C: Implications for Cr(III) mobility and isotopic variations in modern and ancient natural systems

Science.gov (United States)

Babechuk, Michael G.; Kleinhanns, Ilka C.; Reitter, Elmar; Schoenberg, Ronny

2018-02-01

The stable Cr isotope fractionation preserved in natural substances has been attributed predominantly to Cr(III)-Cr(VI) redox transformations. However, non-redox reaction pathways (e.g., ligand-promoted dissolution, ligand exchange, adsorption of Cr(III)) are liable to contribute to isotopic fractionation in natural systems given that soluble Cr(III)-ligands have been directly documented or modeled in several marine, continental, and hydrothermal environments. This study isolates the stable Cr isotope fractionation accompanying Cl-H2O ligand exchange during the transformation of three aqueous species in the Cr(III)-Cl-H2O system, [CrCl2(H2O)4]+aq (abr. CrCl2+ or S1), [CrCl(H2O)5]2+aq (abr. CrCl2+ or S2), and [Cr(H2O)6]3+aq (abr. Cr3+ or S3), at low pH (≤2). In dilute HCl (0.01 to 1 M), Cr3+ is the kinetically favoured species and transformation of CrCl2+ to CrCl2+ to Cr3+ via 2 steps of dechlorination/hydrolyzation begins immediately upon dissolution of a Cr(III)-Cl solid. Individual species are separated with cation exchange chromatography at different stages of transformation and inter- and intra-species (across an elution peak of one species) isotopic fractionation of up to 1 and 2‰ (δ53/52Cr), respectively, is documented. Comparison of peak elution characteristics with Cr-Cl-H-O isotopologue mass abundances suggests mass-dependent sorting of isotopologues alone cannot explain intra-species fractionation, supporting a previously published proposal that preferential adsorption of light Cr isotopes on the resin is driven by vibrational energy effects. The transformation of CrCl2+ to CrCl2+ is faster than CrCl2+ to Cr3+ and the rates of both transformations increase with solution pH. Preferential reaction of light Cr(III) isotopes into product species occurs during each transformation, consistent with closed-system, kinetic fractionation during Cl-H2O ligand exchange. Inter-species fractionation is assessed using time-series experiments beginning from the

Citation Oil and Gas Corporation... Title V Applicability Determination

Science.gov (United States)

This document may be of assistance in applying the Title V air operating permit regulations. This document is part of the Title V Policy and Guidance Database available at www2.epa.gov/title-v-operating-permits/title-v-operating-permit-policy-and-guidance-document-index. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Associations between standardized school performance tests and mixtures of Pb, Zn, Cd, Ni, Mn, Cu, Cr, Co, and V in community soils of New Orleans

International Nuclear Information System (INIS)

Zahran, Sammy; Mielke, Howard W.; Weiler, Stephan; Hempel, Lynn; Berry, Kenneth J.; Gonzales, Christopher R.

2012-01-01

In New Orleans a strong inverse association was previously identified between community soil lead and 4th grade school performance. This study extends the association to zinc, cadmium, nickel, manganese, copper, chromium, cobalt, and vanadium in community soil and their comparative effects on 4th grade school performance. Adjusting for poverty, food security, racial composition, and teacher-student ratios, regression results show that soil metals variously reduce and compress student scores. Soil metals account for 22%–24% while food insecurity accounts for 29%–37% of variation in school performance. The impact on grade point averages were Ni > Co > Mn > Cu ∼Cr ∼ Cd > Zn > Pb, but metals are mixtures in soils. The quantities of soil metal mixtures vary widely across the city with the largest totals in the inner city and smallest totals in the outer city. School grade point averages are lowest where the soil metal mixtures and food insecurity are highest. - Highlights: ► Mixtures of metals vary; largest totals in the inner city and lowest in the outer city. ► An inverse association between soil Pb and 4th grade school performance is known. ► Assuming the same exposure pathway, multiple metals are compared to performance. ► Soil metals account for 22%–24% of variation in school test performance. ► Soil metal plus food insecurity accounts for 54% of explained variance. - Controlling for potential confounding variables, the accumulation of metals (Pb, Zn, Cd, Ni, Mn, Cu, Cr, and Co) in neighborhood soils is significantly negatively associated with 4th grade school performance on standardized tests in New Orleans.

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 577 ... Issue, Title. Vol 20, No 2 (2003), Emergency Contraception: A Global Overview of Knowledge, Attitudes and Practices Among Providers, Abstract PDF. Deborah Haggai. Vol 23 (2006):, Emergency laparotomy for peripartum haemorrhage in Bida North Central Nigeria, Abstract PDF. Sunny Abiodun O ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 155 ... Issue, Title. Vol 12 (2012), Political Dissent and Autonomy in Wum Local Government, Southern (West) Cameroons, 1957 – 1968, Abstract. TP Mbeum. Vol 9 (2009), Post-Emancipation Slave Commerce: Increasing Child Slave Trafficking and Women's Agency in Late Nineteenth-century Ghana ...

Reduction of Cr(VI) to Cr(III) using silicon nanowire arrays under visible light irradiation

Energy Technology Data Exchange (ETDEWEB)

Fellahi, Ouarda [Institut d' Electronique, de Microélectronique et de Nanotechnologie (IEMN), UMR CNRS 8520, Avenue Poincaré—BP 70478, 59652 Villeneuve d' Ascq Cedex (France); Centre de Recherche en Technologie des Semi-conducteurs pour l' Energétique-CRTSE 02, Bd Frantz Fanon, BP. 140, Alger 7 Merveilles (Algeria); Barras, Alexandre [Institut d' Electronique, de Microélectronique et de Nanotechnologie (IEMN), UMR CNRS 8520, Avenue Poincaré—BP 70478, 59652 Villeneuve d' Ascq Cedex (France); Pan, Guo-Hui [State Key Laboratory of Luminescence and Applications, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 3888 Dong Nanhu Road, Changchun 130033 (China); Coffinier, Yannick [Institut d' Electronique, de Microélectronique et de Nanotechnologie (IEMN), UMR CNRS 8520, Avenue Poincaré—BP 70478, 59652 Villeneuve d' Ascq Cedex (France); Hadjersi, Toufik [Centre de Recherche en Technologie des Semi-conducteurs pour l' Energétique-CRTSE 02, Bd Frantz Fanon, BP. 140, Alger 7 Merveilles (Algeria); Maamache, Mustapha [Laboratoire de Physique Quantique et Systèmes Dynamiques, Département de Physique, Université de Sétif, Sétif 19000 (Algeria); Szunerits, Sabine [Institut d' Electronique, de Microélectronique et de Nanotechnologie (IEMN), UMR CNRS 8520, Avenue Poincaré—BP 70478, 59652 Villeneuve d' Ascq Cedex (France); and others

2016-03-05

Highlights: • Cr(VI) reduction to Cr(III) using silicon nanowires decorated with Cu nanoparticles. • The reduction takes place at room temperature and neutral pH under visible light. • The photocatalytic reduction was enhanced by addition of adipic or citric acid. - Abstract: We report an efficient visible light-induced reduction of hexavalent chromium Cr(VI) to trivalent Cr(III) by direct illumination of an aqueous solution of potassium dichromate (K{sub 2}Cr{sub 2}O{sub 7}) in the presence of hydrogenated silicon nanowires (H-SiNWs) or silicon nanowires decorated with copper nanoparticles (Cu NPs-SiNWs) as photocatalyst. The SiNW arrays investigated in this study were prepared by chemical etching of crystalline silicon in HF/AgNO{sub 3} aqueous solution. The Cu NPs were deposited on SiNW arrays via electroless deposition technique. Visible light irradiation of an aqueous solution of K{sub 2}Cr{sub 2}O{sub 7} (10{sup −4} M) in presence of H-SiNWs showed that these substrates were not efficient for Cr(VI) reduction. The reduction efficiency achieved was less than 10% after 120 min irradiation at λ > 420 nm. Addition of organic acids such as citric or adipic acid in the solution accelerated Cr(VI) reduction in a concentration-dependent manner. Interestingly, Cu NPs-SiNWs was found to be a very efficient interface for the reduction of Cr(VI) to Cr(III) in absence of organic acids. Almost a full reduction of Cr(VI) was achieved by direct visible light irradiation for 140 min using this photocatalyst.

24 CFR 203.386 - Coverage of title evidence.

Science.gov (United States)

2010-04-01

... SINGLE FAMILY MORTGAGE INSURANCE Contract Rights and Obligations Property Title Transfers and Title... the public records, there are not, at such date, any outstanding prior liens, including any past-due...

24 CFR 234.65 - Nature of title.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Nature of title. 234.65 Section 234.65 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued... OWNERSHIP MORTGAGE INSURANCE Eligibility Requirements-Individually Owned Units § 234.65 Nature of title. A...

Evaluation of the creep cavitation behavior in Grade 91 steels

International Nuclear Information System (INIS)

Siefert, J.A.; Parker, J.D.

2016-01-01

Even in properly processed Grade 91 steel, the long term performance and creep rupture strength of base metal is below that predicted from a simple extrapolation of short term data. One of the mechanisms responsible for this reduction in strength is the development of creep voids. Importantly, nucleation, growth and inter linkage of voids under long term creep conditions also results in a significant loss of creep ductility. Thus, elongations to rupture of around 5% in 100,000 h are now considered normal for creep tests on many tempered martensitic steels. Similarly, creep damage development in the heat affected zones of welds results in low ductility cracking at times below the minimum expected life of base metal. In all cases, the relatively brittle behavior is directly a consequence of creep void development. Indeed, the results of component root cause analysis have shown that crack development in Grade 91 steel in-service components is also a result of the formation of creep voids. The present paper examines background on the nucleation and development of creep voids in 9%Cr type martensitic steels, presents information regarding methods which allow proper characterization of the creep voids and discusses factors affecting creep fracture behavior in tempered martensitic steels. It is apparent that the maximum zone of cavitation observed in Grade 91 steel welds occurred in a region in the heat affected zone which is ∼750 μm in width. This region corresponds to the band where the peak temperature during welding is in the range of ∼1150–920 °C.The cavity density in this band was over about 700 voids/mm"2 at an estimated creep life fraction of ∼99%. - Highlights: • The present paper examines background on the nucleation and development of creep voids in 9%Cr type martensitic steels. • Information regarding methods which allow proper characterization of the creep voids is also presented. • Factors affecting creep fracture behavior in tempered

Browse Title Index

African Journals Online (AJOL)

Items 51 - 98 of 98 ... Issue, Title. Vol 4, No 1 (2016), First-year seminar intervention: Enhancing firstyear mathematics performance at the University of Johannesburg, Abstract PDF. Melanie Jacobs, Estherna Pretorius. Vol 5, No 2 (2017), From Inky Pinky Ponky to Improving Student Understanding in Assessment: Exploring the ...

Browse Title Index

African Journals Online (AJOL)

Items 551 - 600 of 1463 ... Issue, Title. Vol 15, No 2 (2015), Evaluation of the diagnostic performance and operational characteristics of four rapid immunochromatographic syphilis tests in Burkina Faso, Abstract PDF. FY Bocoum, H Ouedraogo, G Tarnagda, A Kiba, S Tiendrebeogo, F Bationo, B Liestman, S Diagbouga, ...

Browse Title Index

African Journals Online (AJOL)

Items 9951 - 10000 of 11090 ... Issue, Title. Vol 10, No 36 (2011), Study of heavy metals bioaccumulation in the process of vermicomposting, Abstract PDF. MM Aleagha, G Ebadi. Vol 10, No 45 (2011), Study of malondialdehyde (MDA) content, superoxide dismutase (SOD) and glutathione peroxidase (GSH-Px) activities in ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 985 ... Journal Home > Advanced Search > Browse Title Index ... Vol 17 (2010), Alternating Direction Implicit Finite Difference Time Domain Acoustic Wave Algorithm, Abstract. E Ikata .... Vol 17 (2010), Analytic derivation of the wave profile and phase speed of sixth order Stokes waves in deep water, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 451 - 500 of 581 ... Issue, Title. Vol 30, No 1 (2016), Risky sexual behaviour and associated factors among students of Debre Tabor University, Northwest Ethiopia: a cross-sectional study, Abstract PDF. Awoke Derbie, Mekonnen Assefa, Daniel Mekonnen, Fantahun Biadglegne. Vol 28, No 1 (2014), Road traffic accident: ...

THE EFFECT OF RARE EARTH ELEMENTS ON Cr PRECIPITATIONS IN A Cu-0.8WT%Cr ALLOY

Directory of Open Access Journals (Sweden)

Gewang Shuai

2011-05-01

Full Text Available The microstructural evolution of Cu-based alloys during aging was studied using a quantitative metallographic method. Samples were cut from ingots of Cu-0.8wt%Cr and Cu-0.8wt%Cr-RE alloys. These were solution treated at 1000 ºC for 1.5h and subsequently quenched in water, then separately aged at 480 ºC for different durations. The microstructures were observed by optical microscope, and the characteristic geometric parameters of precipitated Cr phase, including volume fraction VV, face density NA, mean diameter and roundness, were measured. These data provided more details about the process of aging. The results showed that precipitation of Cr phase occurred in the form of particles during aging. Rare earth elements promoted the precipitation of Cr phase and dispersed Cr particles. The phenomenon of overaging came earlier in Cu-Cr-RE than in Cu-Cr. In the present work, the optimal aging time at 480 ºC was 2 hrs for the Cu-0.8wt%Cr-RE alloy and 3 hours for the Cu-0.8wt%Cr alloy.

Investigations on diffusion-controlled transformations in creep resistant steels and graded cemented carbides

International Nuclear Information System (INIS)

Prat Borquez, Orlando

2011-01-01

The objective of this work was to simulate diffusion-controlled transformations on engineering alloys designed by the author and his colleagues. The main challenge of the work is to adapt the existing DICTRA models to the experimental processing and working conditions investigated, as well as to find the adequate boundary conditions for the description of the diffusion-controlled transformations governing the microstructure formation and evolution, in order to obtain reliable simulation results. The simulations were compared with experimental results of the microstructure evolution by scanning electron microscopy and scanning transmission electron microscopy (STEM). Two groups of materials were investigated. The first group was 9-12% Cr heat resistant alloys. These alloys are particularly interesting because the microstructure evolves during working conditions. Different compositions were designed in order to form different kinds and amounts of precipitates. For the designed 9-12% Cr creep steels the coarsening of MX and M 23 C 6 particles was modeled by applying the coarsening model implemented in DICTRA. The cell method of DICTRA was applied to investigate the kinetics of the Laves phase growth on 9-12% Cr alloys. The particular objectives of these investigations were: a) to determine the coarsening rate of precipitates, b) to investigate the influence of alloying element on the growth rate of the Laves phase, c) to determine the influence of the M 23 C 6 formation on the growth kinetics of the Laves phase, d) to determine the growth mechanism at the interface of the Laves phase (i.e. up-hill diffusion), e) to investigate the effect of the cell size on the simulation kinetics of Laves phase. The second group of materials was cemented carbides. They are used as cutting tools or wear parts in the automotive, aircraft and mining industry among others. The wear performance of cemented carbides (hardmetals and cermets) can be largely improved by applying wear

14 CFR 1245.109 - Assignment of title to NASA.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Assignment of title to NASA. 1245.109... INTELLECTUAL PROPERTY RIGHTS Patent Waiver Regulations § 1245.109 Assignment of title to NASA. (a) The instrument of waiver set forth in § 1245.115(c) shall be voided by NASA with respect to the domestic title to...

The functionally graded sintered steel WC-Co-NbC matrix

Energy Technology Data Exchange (ETDEWEB)

Santos, A.A.A.; Silva Junior, J.F. [Universidade Federal do Rio Grande do Norte (UFRN), Natal (Brazil)

2009-07-01

Full text: The high speed steels are used for machining, including cutting tools at high speeds because their wear resistance, high temperature properties and excellent hardness. They are ferrous based alloys of the Fe-C-X component system where X represents a group of elements comprising Cr, W or Mo, V and Co. The aim of this work was to study the feasibility of powder metallurgy technique to develop functionally graded alloy material added by WC, Co and NbC. The morphology of the composite powders and sintered MMC were characterized by scanning electron microscopy and XRD measurements. (author)

Structural, electrical, and dielectric properties of Cr doped ZnO thin films: Role of Cr concentration

Energy Technology Data Exchange (ETDEWEB)

Gürbüz, Osman, E-mail: osgurbuz@yildiz.edu.tr; Okutan, Mustafa

2016-11-30

Highlights: • Magnetic material of Cr and semiconductor material of ZnO were grown by the magnetron sputtering co-sputter technique. • Perfect single crystalline structures were grown. • DC and AC conductivity with dielectric properties as a function of frequency (f = 5Hz–13 MHz) at room temperature were measured and compared. • Cr doped ZnO can be used in microwave, sensor and optoelectronic devices as the electrical conductivity increases while dielectric constant decreases with the Cr content. - Abstract: An undoped zinc oxide (ZnO) and different concentrations of chromium (Cr) doped ZnO Cr{sub x}ZnO{sub 1−x} (x = 3.74, 5.67, 8.10, 11.88, and 15.96) thin films were prepared using a magnetron sputtering technique at room temperature. These films were characterized by X-ray diffraction (XRD), High resolution scanning electron microscope (HR-SEM), and Energy dispersive X-ray spectrometry (EDS). XRD patterns of all the films showed that the films possess crystalline structure with preferred orientation along the (100) crystal plane. The average crystallite size obtained was found to be between 95 and 83 nm which was beneficial in high intensity recording peak. Both crystal quality and crystallite sizes decrease with increasing Cr concentration. The crystal and grain sizes of the all film were investigated using SEM analysis. The surface morphology that is grain size changes with increase Cr concentration and small grains coalesce together to form larger grains for the Cr{sub 11.88}ZnO and Cr{sub 15.96}ZnO samples. Impedance spectroscopy studies were carried out in the frequencies ranging from 5 Hz to 13 MHz at room temperature. The undoped ZnO film had the highest dielectric value, while dielectric values of other films decreased as doping concentrations increased. Besides, the dielectric constants decreased whereas the loss tangents increased with increasing Cr content. This was considered to be related to the reduction of grain size as Cr content in Zn

Modeling on Fe-Cr microstructure: evolution with Cr content

International Nuclear Information System (INIS)

Diaz Arroyo, D.; Perlado, J.M.; Hernandez-Mayoral, M.; Caturla, M.J.; Victoria, M.

2007-01-01

Full text of publication follows: The minimum energy configuration of interstitials in the Fe-Cr system, which is the base for the low activation steels being developed in the European fusion reactor materials community, is determined by magnetism. Magnetism plays also a role in the atomic configurations found with increasing Cr content. Results will be presented from a program in which the microstructure evolution produced after heavy ion irradiation in the range from room temperature to 80 K is studied as a function of the Cr content in alloys produced under well controlled conditions, i.e. from high purity elements and with adequate heat treatment. It is expected that these measurements will serve as matrix for model validation. The first step in such modeling sequence is being performed by modeling the evolution of displacement cascades in Fe using the Dudarev -Derlet and Mendeleev potentials for Fe and the Caro potential for Fe-Cr. It is of particular interest to study the evolution of high-energy cascades, where an attempt will be made to clarify the role of the evolution of sub-cascades. Kinetic Monte Carlo (kMC) techniques will be used then to simulate the defect evolution. A new parallel kMC code is being implemented for this purpose. (authors)

Browse Title Index

African Journals Online (AJOL)

Items 101 - 108 of 108 ... Issue, Title. Vol 8, No 2 (2016), The status and challenges of clinical informatics development in South Africa, Abstract PDF. Abayomi Kehinde Owolabi, Thokozani Patrick Mhlongo, Neil Evans. Vol 4, No 1 (2012), The stuttering implementation of language policies in the South African education system ...

Browse Title Index

African Journals Online (AJOL)

Items 751 - 800 of 846 ... Journal Home > Advanced Search > Browse Title Index ... Vol 9, No 3S (2017): Special Issue, The effect of torrefaction on oil palm ... core competency skills of IRBM tax auditors towards their performance, Abstract PDF ... of exchange rates behavior in Malaysia by using NATREX model, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 51 - 76 of 76 ... Issue, Title. Vol 6, No 1 (2013), Integrating Sustainability into the Real Estate Valuation Process: A Nigerian Perspective, Abstract PDF. G K Babawale, B A Oyalowo. Vol 5, No 1 (2012), Internalising internationa valuation standards: Relevance and applicability issues in the Nigerian context, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 201 ... Issue, Title. Vol 12, No 1 (2006), Conservative management of cervical ectopic pregnancy: case report, Abstract PDF. TD Naidoo, MR Ramogale, J Moodley. Vol 18, No 2 (2012), Contraceptive use and associated factors among South African youth (18 - 24 years): A population-based survey, Abstract ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 76 ... Issue, Title. Vol 16, No 2 (2006), A profile of the theatre procedures in paediatrict ophthalmic practice, Abstract. E O Onwasigwe. Vol 15, No 2 (2005), Abdominal cocoon, Abstract. Abdulrasheed K Adesunkanmi, Tajudeen A Badmus, Olukayode Ogundoyin, Akinwumi B Ogunrombi. Vol 18, No 1 (2008) ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 93 ... Issue, Title. Vol 5 (2013), A cost-effective Geographic Information Systems for Transportation (GIS-T) application for traffic congestion analyses in the Developing World, Abstract PDF. E Agyemang. Vol 3 (2011), A Historical and Gendered Perspective on HIV / AIDS in Botswana, Abstract PDF. J Hesselberg ...

Browse Title Index

African Journals Online (AJOL)

Items 301 - 350 of 577 ... Issue, Title. Vol 32, No 2 (2015), Late arrival in hospital during labour: any correlation with materno-foetal outcome? The state specialist hospital, Asubiaro, Osogbo Experience. Abstract PDF. OO Awolola. Vol 30, No 2 (2013), Late Reproductive Effects of Cancer Treatment in Young People, Abstract ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 251 ... Issue, Title. Vol 55 (2014), 20 Years of democracy: Transforming the public service, Abstract. A Ruiters. Vol 63 (2016), Zemk' iinkomo magwala ndini! Wake up! The cows are being stolen! Abstract. Sipho Pityana. Vol 56 (2014), A layperson's guide to Nene's budget statement, Abstract. B Turok.

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 1007 ... Issue, Title. Vol 11, No 1 (1997), (+)-Floribundone 3 from the pods of Senna septemtrionalis, Details PDF. Gizachew Alemayehu, Bekuretsion Woldeyesus, Berhanu M Abegaz. Vol 14, No 1 (2000), 11α-Hydroxy muzigadiolide, a novel drimane sesquiterpene from the stem bark of warburgia ugandensis ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 170 of 170 ... Issue, Title. Vol 20, No 2 (2004), The Impact of Mine Closures on Rural Population Dynamics: The Case of Zhombe in Kwekwe District, Midlands Province, Zimbabwe, Abstract. Crescentia Madebwe. Vol 29, No 1 (2013), The Influence of Organisational Culture and Job Satisfaction on Intentions to ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 633 ... Issue, Title. Vol 19, No 1 (2009), Delays in Tuberculosis Treatment and Associated Factors in Jimma Zone, Southwest Ethiopia, Abstract PDF. Ayalew Tegegn, Meseret Yazachew. Vol 26, No 1 (2016), Delivery Site Preferences and Associated Factors among Married Women of Child Bearing Age in ...

Browse Title Index

African Journals Online (AJOL)

Items 251 - 300 of 367 ... Issue, Title. Vol 43 (2014), Some interlingual communicative challenges for foreign African interpreters in South African courtrooms, Abstract PDF. SE Usadolo, E Kotze. Vol 29 (1996), South Africa's new language policy in the context of the organisation for African unity's language plan of action for ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 110 ... Issue, Title. Vol 10, No 1 (2003), Incidence and Determinants of Child Labour in Nigeria: Implications for Poverty Alleviation, Abstract. Benjamin Chiedozie Okpukpara, Ngozi Odurukwu. Vol 20, No 1 (2013), Inflation and capacity utilisation in Nigeria's manufacturing sector, Abstract. OA Ishola. Vol 19, No ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 643 ... Issue, Title. Vol 18, No 2 (2015), Contraceptive Knowledge and Compliance with Guidelines for Providing Contraceptive Services by Patent Medicine Vendors In Ibadan North Local Government Area, Nigeria, Abstract PDF. OO Ajayi, AJ Ajuwon. Vol 16, No 2 (2013), Coping Strategy for Food Security ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 8, No 2 (2016): Supplement, Using operative models (ICF and CBR) within an interprofessional context to address community needs, Abstract PDF. A Rhoda, F Waggie, G.C. Filies, J.M. Frantz. Vol 2, No 1 (2010), Using portfolios to assess professional competence and development in medical laboratory ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 43, No 2 (2006), Review: "'n Wonderlike geweld. Jeugherinneringe", By Elsa Joubert (2005), Abstract PDF. Henriette Roos. Vol 53, No 1 (2016), Review: Breyten Breytenbach, A Monologue in Two Voices, Abstract PDF. Andy Carolin. Vol 53, No 1 (2016), Review: The Shadow of the Hummingbird, Abstract ...

crRNA biogenesis

NARCIS (Netherlands)

Charpentier, E.; Oost, van der J.; White, M.

2013-01-01

Mature crRNAs are key elements in CRISPR-Cas defense against genome invaders. These short RNAs are composed of unique repeat/spacer sequences that guide the Cas protein(s) to the cognate invading nucleic acids for their destruction. The biogenesis of mature crRNAs involves highly precise processing

Compatibility of vanadium alloys with reactor-grade helium for fusion reactor applications

International Nuclear Information System (INIS)

Bell, G.E.C.; Bishop, P.S.

1993-01-01

Tests were conducted to determine the compatibility of vanadium alloys with reactor-grade helium and to define the helium gas chemistry requirements for fusion reactors, miniature tensile specimens of V-5Cr-5Ti. V-10Cr-5Ti, and V-12.5Cr-5 Ti were exposed in a once-through system to helium with 70 vppm-H 2 (measured oxygen partial pressures of 10 -12 atm) and bottle helium (measured oxygen partial pressures of -4 atm) between 500 and 700 degree C for up to 1008 h. The weight changes in the specimens were recorded. The helium-exposed specimens were tensile tested, and the effects of exposure on mechanical properties were assessed. Exposure between 500 and 700 degree C for 1008 h in He+70 vppm-H 2 resulted in complete embrittlement of all the alloys in room temperature tensile tests. The fracture mode was primarily cleavage, probably caused by a hydrogen-induced shift in the ductile to brittle transition temperature (DBTT). Weight gains increased with temperature and were largest for the V-5Cr-5Ti alloy. Specimens exposed for 531 h between 500 and 700 degree C in bottle He exhibited two distinct fracture morphologies on the fracture surfaces. Brittle cleavage around the edges of specimens gave way to ductile dimpling in the center of the specimens. The brittle region around the periphery of the specimen is most likely the highest vanadium oxide. V 2 O 5

What is the title of a Web page? A study of Webography practice

Directory of Open Access Journals (Sweden)

Timothy C. Craven

2002-01-01

Full Text Available Few style guides recommend a specific source for citing the title of a Web page that is not a duplicate of a printed format. Sixteen Web bibliographies were analyzed for uses of two different recommended sources: (1 the tagged title; (2 the title as it would appear to be from viewing the beginning of the page in the browser (apparent title. In all sixteen, the proportion of tagged titles was much less than that of apparent titles, and only rarely did the bibliography title match the tagged title and not the apparent title. Convenience of copying may partly explain the preference for the apparent title. Contrary to expectation, correlation between proportion of valid links in a bibliography and proportion of accurately reproduced apparent titles was slightly negative.

Enhancement strategies for Cu(II), Cr(III) and Cr(VI) remediation by a variety of seaweed species.

Science.gov (United States)

Murphy, V; Hughes, H; McLoughlin, P

2009-07-15

Various chemical treatments have been applied to six brown, red and green seaweed species with a view to enhancing their metal removal for Cu(II), Cr(III) and Cr(VI). Treatment with acetone resulted in the greatest enhancement for both cationic and anionic species with relatively low mass losses (15-35%), indicating its low risk to biomass operational stability. Cation binding was increased by 69%, while the total Cr removal was augmented by 15%. Cr(VI) binding was shown to be an adsorption-coupled reduction, whereby Cr(VI) was bound to the biomass surface at pH 2 and subsequently reduced to Cr(III). Acetone treatment also resulted in biomasses that were capable of converting up to 83% of Cr(VI) in solution to Cr(III). Blocking of carboxyl and amino functionalities had significant negative effects both on total Cr removal as well as percentage conversion of Cr(VI) to Cr(III). Results therefore indicated the significant role played by these moieties in metal binding to these seaweeds. Potentiometric titrations displayed agreement between the degree of esterification and the decrease in Cu(II) removal for Ulva spp. and Polysiphonia lanosa. FTIR analysis identified changes in biomass functionality and availability after chemical modification, the results of which were in agreement with metal removal studies. In conclusion, these biosorbents represent suitable candidates to replace conventional removal technologies for metal bearing wastewaters, in particular for the detoxification of hazardous Cr(VI) waste streams.

The effect of magnetic ordering on the giant magnetoresistance of Cr-Fe-V and Cr-Fe-Mn

International Nuclear Information System (INIS)

Somsen, Ch.; Acet, M.; Nepecks, G.; Wassermann, E.F.

2000-01-01

Cr-rich Cr 1-x Fe x alloys with compositions in the vicinity of mixed ferromagnetic and antiferromagnetic exchange (x=0.18) exhibit giant magnetoresistance. In order to understand the influence of the antiferromagnetism of Cr on the giant magnetoresistance one can manipulate the antiferromagnetic exchange either by adding vanadium, which destroys the antiferromagnetism of Cr, or by adding manganese, which enhances it. Cr-Fe-V and Cr-Fe-Mn alloys also have Curie temperatures that lie between low temperatures and room temperature in the concentration region where giant magnetoresistance is observed. Therefore, they are also used as samples to study the magnetoresistance as a function of the strength of FM exchange. We discuss these points in the light of temperature and concentration-dependent magnetoresistance experiments on Cr 0.99-x Fe x V 0.01 , Cr 0.96-x Fe x V 0.04 , Cr 0.90-x Fe x Mn 0.10 and Cr 0.55 Fe x Mn 0.45-x alloys. Results indicate that the most favorable condition for a large magnetoresistance in these alloys occurs at temperatures near the Curie temperature

Effects of alloying and temperature on the high-temperature oxidation of Cr-Cr{sub 2}Nb

Energy Technology Data Exchange (ETDEWEB)

Tortorelli, P.F.; DeVan, J.H. [Oak Ridge National Lab., TN (United States); Carson, L.J. [Lincoln Univ., PA (United States)

1993-06-01

Effects of alloying additions and temperature on isothermal and cyclic oxidation resistance of Cr-Cr{sub 2}Nb alloys were examined for air exposures. An isothermal exposure temperature of 1100C led to rapid reaction of binary Cr-12 at.% Nb as manifested a high oxidation rate and nonprotective behavior. Generally parabolic kinetics, complicated by some isothermal scale cracking, were observed at 900--1000C. Scale damage was exacerbated by thermal cycling. The addition of 8 at.% Al to Cr-12 at.% Nb did not effect cyclic oxidation resistance, but there was some evidence that scale adherence on Cr-6 at.% Nb-8 at.% Al was better than that for binary Cr-6 at.% Nb. Alloying additions of Al (up to 18 at.%) or Re (2 at.%) did not improve the isothermal oxidation resistance of Cr-12 at.% Nb. However, the tendency for scale damage during both isothermal and thermal cycling exposures suggests that alloying additions that specifically improve scale plasticity or modify growth stresses could be effective for Cr-Nb alloys. 10 refs, 9 figs, 1 tab.

Alloying effect on hardening of martensite stainless steels of the Fe-Cr-Ni and Fe-Cr-Co systems

International Nuclear Information System (INIS)

Fel'dgandler, Eh.G.; Savkina, L.Ya.

1975-01-01

The effect of alloying elements is considered on the γ → a-transformation and hardening of certain compositions of the ternary Fe-Cr-Ni- and Fe-Cr-Co alloy systems with the martensite structure. In martensite Fe-(10 to 14)% Cr base steels the elements Co, Cu, W, Ni, Mo, Si, Cr decrease, Mn, Si, Mo, Cu increase, and Cr, Ni, Co decrease the temperature of α → γ-transition. The tempering of martensite steels of the Fe-Cr-Ni- and Fe-Cr-Co-systems containing 10 to 14% Cr, 4 to 9% Ni, and 7 to 12% Co does not lead to hardening. Alloyage of the martensite Fe-Cr-Ni-, Fe-Cr-Co- and Fe-Cr-Ni-Co base separately with Mo, W, Si or Cu leads to a hardening during tempering, the hardening being the higher, the higher is the content of Ni and, especially, of Co. The increase in the content of Mo or Si produces the same effect as the increase in the Co content. In on Fe-Cr-Co or Fe-Cr-Ni-Co based steels alloyed with Mo or Si, two temperature ranges of ageing have been revealed which, evidently, have different hardening natures. The compositions studied could serve as the base material for producing maraging stainless steels having a complex variety of properties

Browse Title Index

African Journals Online (AJOL)

Items 1 - 20 of 20 ... Issue, Title. Vol 9, No 2 (2000), Age dependent changes in the hypothalamic amino acid neurotransmitters in response to nicotine, Abstract. NM Radwan, NA Ahmed, YAM Aly. Vol 9, No 2 (2000), Autoantibodies, ocular and auditory changes in patients with vitiligo, Abstract. AE Fathia, EA Nagwa, ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 183 of 183 ... Issue, Title. Vol 9, No 1 (2004), Socio-economic constraints affecting youths involvement in national economic development, Abstract. Josephine U Nwagwu. Vol 12, No 2 (2007), Stabilizing Potential Of Cement-Fly Ash Mixture On Expansive Clay Soil, Abstract. OO Amu, AB Fajobi, SO Afekhuai. Vol 11 ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 670 ... Issue, Title. Vol 9, No 2 (2012), Business Planning and the Economic Growth of Small and Medium Scale Enterprises in Nigeria, Abstract. Egbe Aneozeng A, Ejoh Ndifon Ojong, Obo Ekpenyong Bassey. Vol 11, No 2 (2014), Calabar Humaphors: An Analysis of Selected Jokes in Nigerian Stand Up ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 25, No 2 (2005), Yam-based farm practices and nematode problems in stored yams (Dioscorea spp.) in Ghana, Abstract PDF. CK Kwoseh, RA Plowright, J Bridge, R Asiedu. Vol 27, No 2 (2007), Yield, irrigation production efficiency and economic returns of broccoli under variable drip irrigation and lateral ...

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 11090 ... Issue, Title. Vol 12, No 49 (2013), In vitro regeneration of selected Kenyan papaya (Carica papaya L.) lines through shoot tip culture, Abstract PDF. Naomi Nzilani Mumo, Fredah Karambu Rimberia, George Edward Mamati, Agnes Wanjiru Kihurani. Vol 7, No 12 (2008), In vitro regeneration of Turkish ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 232 ... Issue, Title. Vol 5 (2003), Pre-School Education for a Democratic Society: Identifying Views of Stakeholders in Tanzania, Abstract. Willy LM Komba, Satoki T Mahenge, Gadi Koda. Vol 13, No 2 (2012), Process of Assuring Quality in Counselling at the National Open University of Nigeria: A Critique ...

Browse Title Index

African Journals Online (AJOL)

Items 501 - 550 of 670 ... Issue, Title. Vol 11, No 4 (2014), Strategies for Fostering Creativity Among Business Education Graduates in Nigeria, Abstract. BO Nwosu, KE Ojo. Vol 13, No 1 (2015) ... Vol 10, No 1 (2013), The Challenges Facing Accounting Education: The Nigerian Experience, Abstract. OR Okolie. Vol 5 (2008), The ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 183 ... Issue, Title. Vol 62 (2017), #SchoolsOnFire: Criminal justice responses to protests that impede the right to basic education, Abstract PDF. Ann Skelton, Martin Nsibirwa. Vol 45 (2013), 'Pale Face'/'Pointy Face: SA Criminology in Denial, Abstract PDF. S Henkeman. Vol 59 (2017), Aluta continua: Police ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 38, No 1 (2004), Book Review: Unexpected Voices – Theory, Practice and Identity in the Writing Classroom. Abstract. Charly Dyers. Vol 38, No 1 (2004), Book Review: Shelley Angelil-Carter: Stolen Language? Plagiarism in Writing. Abstract. Elizabeth de Kadt. Vol 37, No 1 (2003), Book Review: The Green ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 23, No 2 (2011), Dynamique foliaire et croissance du maïs: Application du modèle «STICS» en conditions tropicales en RD-Congo, Abstract PDF. MM Lufuluabo, RV Kizungu, KK Nkongolo. Vol 18, No 1 (2006), Dynamique spatio-temporelle des populations d\\'Altises Podagrica spp. (Coleoptera ...

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 661 ... Journal Home > Advanced Search > Browse Title Index. Log in or Register to get access to full text downloads. .... A El-Mahdy, B Bolduc, J Upadhyay, R Shoukr, A Khoury. Vol 19, No 1 (2013), Factors affecting lower calyceal stone clearance after Extracorporeal shock wave lithotripsy, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 367 ... Issue, Title. Vol 42 (2013), Nursing the Cure: A Phonetic Analysis of /ʊə/ in South African English, Abstract PDF. I Bekker. Vol 1 (1980), Nuwe ontwikkelings binne chomsky se teorle van kerngrammatika, Abstract PDF. J Maartens. Vol 42 (2013), Obligatory Reflexivity in a Minimalist Grammar of ...

Browse Title Index

African Journals Online (AJOL)

Items 651 - 700 of 1007 ... Issue, Title. Vol 4, No 1 (1990), Kinetics of oxidation of β-diimihe macrocyclic complexes and accessibility of six-coordinate copper(III) complexes generated by electrochemical oxidation of copper(II) complexes, Abstract PDF. Mohamed A. Khalifa. Vol 14, No 2 (2000), Kinetics of periodate oxidation of ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 22, No 2 (2008), Voltammetric determination of heparin based on its interaction with malachite green, Abstract PDF. Xueliang Niu, Weili Zhang, Na Zhao, Wei Sun. Vol 22, No 2 (2008), Voltammetric determination of l-cysteic acid on a 1-[4-(ferrocenyl-ethynyl)phenyl]-1-ethanone modified carbon paste ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 265 ... Issue, Title. Vol 35, No 2 (2008), Choice of place for childbirth: prevalence and correlates of utilization of health facilities in Chongwe district, Zambia, Abstract PDF. AN Hazemba, S Siziya. Vol 43, No 1 (2016), Clinical and Radiological Features of Multiple Myeloma Patients at the University Teaching ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 88, No 8 (1998), New birth and death registration forms - a foundation for the future, a challenge for health workers? Abstract PDF. Debbie Bradshaw, Danuta Kielkowski, Freddy Sitas. Vol 83, No 3 (1993), New estimates of infant and child mortality for blacks in South Africa, 1968-1979, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 851 - 900 of 1006 ... Issue, Title. Vol 54, No 2 (2012), The effect of the introduction of a standard monitoring protocol on the investigations performed on the metabolic control of type 2 diabetes at Addington Hospital Medical Outpatients Department, Durban, South Africa, Abstract PDF. JM Gill, A Ross, F Pirie, ...

Adsorption of Cr(VI and Speciation of Cr(VI and Cr(III in Aqueous Solutions Using Chemically Modified Chitosan

Directory of Open Access Journals (Sweden)

ChunYuan Tao

2012-05-01

Full Text Available A new type of grafting chitosan (CTS was synthesized using 2-hydroxyethyl- trimethyl ammonium chloride (HGCTS. The adsorption of Cr(VI on HGCTS was studied. The effect factors on adsorption and the adsorption mechanism were considered. The results indicated that the HGCTS could concentrate and separate Cr(VI at pH 4.0; the adsorption equilibrium time was 80 min; the maximum adsorption capacity was 205 mg/g. The adsorption isotherm and kinetics were investigated, equilibrium data agreed very well with the Langmuir model and the pseudo second-order model could describe the adsorption process better than the pseudo first-order model. A novel method for speciation of Cr(VI and Cr(III in environmental water samples has been developed using HGCTS as adsorbent and FAAS as determination means. The detection limit of this method was 20 ng/L, the relatively standard deviation was 1.2% and the recovery was 99%~105%.

Effect of free Cr content on corrosion behavior of 3Cr steels in a CO2 environment

Science.gov (United States)

Li, Wei; Xu, Lining; Qiao, Lijie; Li, Jinxu

2017-12-01

The corrosion behavior of 3Cr steels with three microstructures (martensite, bainite, combined ferrite and pearlite) in simulated oil field formation water with a CO2 partial pressure of 0.8 MPa was investigated. The relationships between Cr concentrations in corrosion scales and corrosion rates were studied. The precipitated phases that contained Cr were observed in steels of different microstructures, and free Cr content levels were compared. The results showed that steel with the martensite microstructure had the highest free Cr content, and thus had the highest corrosion resistance. The free Cr content of bainite steel was lower than that of martensite steel, and the corrosion rate of bainite steel was higher than that of martensite steel. Because large masses of Cr were combined in ferrite and pearlite steel, the corrosion rates of ferrite and pearlite steel were the highest. Free Cr content in steel affects its corrosion behavior greatly.

Diverse anaerobic Cr(VI) tolerant bacteria from Cr(VI)-contaminated 100H site at Hanford

Science.gov (United States)

Chakraborty, R.; Phan, R.; Lam, S.; Leung, C.; Brodie, E. L.; Hazen, T. C.

2007-12-01

Hexavalent Chromium [Cr(VI)] is a widespread contaminant found in soil, sediment, and ground water. Cr(VI) is more soluble, toxic, carcinogenic, and mutagenic compared to its reduced form Cr(III). In order to stimulate microbially mediated reduction of Cr(VI), a poly-lactate compound HRC was injected into the chromium contaminated aquifers at site 100H at Hanford. Based on the results of the bacterial community composition using high-density DNA microarray analysis of 16S rRNA gene products, we recently investigated the diversity of the dominant anaerobic culturable microbial population present at this site and their role in Cr(VI) reduction. Positive enrichments set up at 30°C using specific defined anaerobic media resulted in the isolation of an iron reducing isolate strain HAF, a sulfate reducing isolate strain HBLS and a nitrate reducing isolate, strain HLN among several others. Preliminary 16S rDNA sequence analysis identifies strain HAF as Geobacter metallireducens, strain HLN as Pseudomonas stutzeri and strain HBLS as a member of Desulfovibrio species. Strain HAF isolated with acetate as the electron donor utilized propionate, glycerol and pyruvate as alternative carbon sources, and reduced metals like Mn(IV) and Cr(VI). Growth was optimal at 37°C, pH of 6.5 and 0% salinity. Strain HLN isolated with lactate as electron donor utilized acetate, glycerol and pyruvate as alternative carbon sources, and reduced metals like Mn(IV) and Cr(VI). Optimal growth was observed at 37°C, at a pH of 7.5 and 0.3% salinity. Anaerobic active washed cell suspension of strain HLN reduced almost 95 micromolar Cr(VI) within 4 hours relative to controls. Further, with 100 micromolar Cr(VI) as the sole electron acceptor, cells of strain HLN grew to cell numbers of 4.05X 107/ml over a period of 24hrs after an initial lag, demonstrating direct enzymatic Cr(VI) reduction by this species. 10mM lactate served as the sole electron donor. These results demonstrate that Cr

Elaboration, characterization of CrN- based coatings

International Nuclear Information System (INIS)

Tlili, B.; Nouveau, C.; Guillemot, G.

2011-01-01

Cr, CrN and CrAlN monolayers were synthesized by RF dual magnetron sputtering on AISI4140 steel and silicon substrates at 200 deg. C. Multilayers coatings based on the three mono-layers such as CrN/CrAlN and Cr/CrN/CrAlN were also synthesized only on Si. The physico-chemical and mechanical properties of the layers were determined by AFM, SEM+WDS, stress, roughness and nanoindentation measurements. The influence of the thickness on the mechanical properties of the monolayers stresses has been studied and as a consequence we compared the mono and multilayers stress state.

Chromium-rich lawsonite in high-Cr eclogites from the Făgăras Massif (South Carpathians)

Science.gov (United States)

Negulescu, E.; Săbău, G.

2012-12-01

Lawsonite is a relatively rare phase in natural rocks, because of its thermal decomposition during exhumation, and Cr-bearing lawsonite being restricted to only a few occurrences worldwide. Here we report Cr-lawsonite in eclogites hosted in a medium-grade metamorphic complex. Several high-Cr eclogite lenses occur in the Topolog Complex (Făgăras Massif) of dominantly gneissic-amphibolitic composition. High Cr contents are the result of emerald-green mm-sized nodules containing Cr-rich minerals, embedded in a gray-green matrix of kyanite, clinopyroxene, garnet, amphibole, zoisite, and rutile. Garnets occur as porphyroblasts or in coronas around clinopyroxene aggregates probably replacing former magmatic pyroxene. Relict gabbroic textures (sometimes pegmatoid) and whole rock geochemistry indicate a gabbroic cumulate origin. The REE pattern, displaying a slight positive Eu anomaly and a tea spoon-shaped LREE depletion is also indicative of a cumulate origin, as also noted by Pe Piper & Piper (2002) for the Othrys gabbro (as well as others in the Vourinos and Pindos ophiolitic suites) with the same unusual REE-pattern. The emerald-green Cr-rich nodules are unevenly distributed in the rock, and always enclosed in Cr-rich clinopyroxenes (up to 5.46% Cr2O3) which may exhibit Cr-diffusion haloes towards normal Cr-free matrix pyroxene. The nodules consist of diablastic chromite, rutile and Cr-rich kyanite of up to 15.67 wt% Cr2O3, Cr-bearing epidote, to which Cr-rich staurolite (up to 10.45% Cr2O3; XMg up to 0.68) and Cr-rich lawsonite (up to 9.17% Cr2O3) may exceptionally associate. Cr concentrations in kyanite and lawsonite are, to our knowledge, the highest reported so far. Cr-lawsonite was identified in a single sample, as small single phase inclusions armoured in Cr-kyanite. Equilibrium PT-conditions of 2.6 GPa and 610o C were derived from the garnet-mantled clinopyroxene aggregates using multi-equilibria calculation with the PTGIBBS routine of Brandelik & Massonne

Bicarbonate catalysis of exchange synthesis of [51Cr]Cr(III)-EDTA and other chromium complexes

International Nuclear Information System (INIS)

Aronson, F.L.; Strashun, A.M.; Lopez, C.; Steigman, J.

1993-01-01

Exchange syntheses of trivalent chromium complexes often require heating, thus limiting tagging of heat-sensitive biological compounds with 51 Cr. Bicarbonate at pH 6, accelerates the formation of mM Cr-EDTA. Accordingly, room temperature catalysis with [ 51 Cr]Cr(III) at 10 -7 -10 -8 M was investigated. Complexes were successfully formed with EDTA and iminodiacetic acid (electrophoretic analysis) and acetylacetone and tropolone (analyzed by chloroform extraction). The formation of these complexes normally requires extensive heating. (author)

Oxidation study of Cr-Ru hard coatings

Energy Technology Data Exchange (ETDEWEB)

Chen, Yung-I, E-mail: yichen@mail.ntou.edu.tw; Kuo, Yu-Chu; Chen, Sin-Min

2012-01-01

Cr-Ru alloy coatings with Cr content ranging from 47 to 83 at.% were deposited at 400 Degree-Sign C by direct current magnetron co-sputtering with a Ti interlayer on silicon substrates. With a total input power of 300 W, the Cr content in the Cr-Ru coatings increased linearly with the increasing input power of Cr. The intermetallic compound phase Cr{sub 2}Ru with columnar structure was identified for the as-deposited Cr{sub 56}Ru{sub 44} and Cr{sub 65}Ru{sub 35} coatings, resulting in an increase of hardness up to 15-16 GPa. To evaluate the performance of Cr-Ru coatings as a protective coating on glass molding dies, the annealing treatment was conducted at 600 Degree-Sign C in a 50 ppm O{sub 2}-N{sub 2} atmosphere. The outward diffusion and preferential oxidization of Cr in the Cr-Ru coatings resulted in the variations of the crystalline structure, chemical composition distribution, and surface hardness after annealing. X-ray diffraction and transmission electron microscopy (TEM) proved that an oxide scale consisting of Cr{sub 2}O{sub 3} formed on the free surface. Scanning electron microscopy and TEM observed the surface morphology and structural variation. The chemical composition depth profiles were analyzed by Auger electron microscopy, verifying the presence of a Cr-depleted zone beneath the oxide scale. The hardness of Cr{sub 56}Ru{sub 44} and Cr{sub 65}Ru{sub 35} coatings decreased to 11-12 GPa after annealing, accompanied by the replacement of the Cr{sub 2}Ru phase by the Ru phase. - Highlights: Black-Right-Pointing-Pointer We prepared crystalline Cr-Ru alloy coatings by direct current magnetron sputtering. Black-Right-Pointing-Pointer Cr-Ru coatings were annealed at 600 Degree-Sign C for 2 h in a 50 ppm O{sub 2}-N{sub 2} atmosphere. Black-Right-Pointing-Pointer Cr diffused outwardly and oxidized to form a stable and protective oxide scale. Black-Right-Pointing-Pointer The original columnar grains recrystallized to polycrystalline grains.

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 100 ... Issue, Title. Vol 28 (2013): Special Issue, Occurrence of Cryptosporidium and Giardia in domestic animals in peri-urban communities of Kafue district, Zambia, Abstract. J Siwila, IGK Phiri, HI Enemark, M Nchito, A Olsen. Vol 26, No 1 (2009), Occurrence of foot and mouth disease serotypes in Tanzania: A ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 15 of 15 ... Issue, Title. Vol 1, No 1 (2008), Assessment Of Ophthalmic Patients' Satisfaction In Owo, Abstract. CO Omolase, CO Fadamiro, BO Omolase, AS Aina, EO Omolade. Vol 3, No 1 (2010), Case Report: Strongyloides stercoralis coinfection in a Nigerian with HIV. Abstract. A.A Oyekunle, R.A.A Bolarinwa, O.A ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 15 of 15 ... Issue, Title. Vol 1, No 1 (2007), An Action Five Strategy For Bridging The Gender Gap In Academic Research Activities In African Universities. The Case of Nigeria, Abstract PDF. DN Okorie, OG Agabi, CM Uche. Vol 1, No 1 (2007), Book Review: Confronting sexual harassment in Ghanaian Universities ...

Browse Title Index

African Journals Online (AJOL)

Items 201 - 240 of 240 ... Issue, Title. Vol 8, No 4 (2005), Status equipment in primary health centres of Tafa Lga, North Central Nigeria, Abstract. MN Sambo, I Lewis, K Sabitu. Vol 10, No 1 (2007), Stroke at a tertiary medical institution in Northern Nigeria: Patients\\' profile and predictors of outcome, Abstract. KW Wahab, MU ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 107 of 107 ... Issue, Title. Vol 6, No 1 (2017), The Ophthalmic status manifestations of nutritional and lifestyle disorders of men in a peri urban community in Ghana, Abstract PDF. F. Vuvor, M. Steiner-Asiedu, F.K. Saalia. Vol 2, No 1 (2013), Thyroid Disorders in Accra, Ghana: A Retrospective Histopathological Study ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 165 ... Issue, Title. Vol 30 (2005), Digitisation projects at the University of Cape Town Libraries, Abstract. Janine Dunlop, Lesley Hart. Vol 24 (2002), DISA: an African Perspective on Digital Technology, Abstract. Michele Pickover, Dale Peters. Vol 30 (2005), Doing it right – or are we? Basic principles in the ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 66 ... Issue, Title. Vol 48, No 1-2 (2015), A hierarchical modeling of information seeking behavior of school teachers in rural areas of Nigeria, Abstract. Manir Abdullahi Kamba. Vol 49, No 1-2 (2016), Access to electronic information resources by students of federal college of education in south east Nigeria ...

Browse Title Index

African Journals Online (AJOL)

Items 351 - 400 of 400 ... Issue, Title. Vol 9, No 1 (2010), Soft tissue sarcoma of the thigh: Need for angiography in the developing, Abstract PDF. IA Adigun, GA Rahman, KO Ogundipe. Vol 3, No 1 (2004), Spectrum of rheumatic heart disease in Zaria, Northern Nigeria, Abstract. SS Danbauchi, MA Alhassan, SO David, ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 68 of 68 ... Issue, Title. Vol 12, No 1-2 (2009), Sécurité et ordre politique au Cameroun : entre dynamiques internes et connexions internationales, Abstract PDF. BEP Chantal. Vol 6, No 1-2 (2003), Self-Determination, Nationalism, Development and Pan-Africanism Stuck on the Runway: Are Intellectuals to be Blamed ...

Browse Title Index

African Journals Online (AJOL)

Items 251 - 300 of 328 ... Issue, Title. Vol 7, No 1 (2003), Sexual Harassment in Academia in Nigeria: How Real? Details PDF. Olugbenga Jelil Ladebo. Vol 8, No 2 (2004), Shaping the internet for match-making/dating: a challenge for the contemporary Nigerian family institution, Abstract PDF. Wale Adesina. Vol 6, No 1 (2002) ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 198 ... Issue, Title ... Vol 7, No 1 (2013), Enterprise Cloud Adoption: Leveraging on the Business ... Load Balancing And Job Scheduling In Cloud Computing ... Vol 13, No 1 (2015), ICT-Based Framework for Improved Food Security in Nigeria ... Vol 5, No 1 (2012), IT-Based Solutions to the Electoral System in ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 20, No 1 (2015), Assessment of iron status among preschool children (6 to 59 months) with and without malaria in Western Province, Kenya, Abstract. I Kisiangani, C Mbakaya, A Makokha, D Magu. Vol 20, No 1 (2015), Assessment of iron status among preschool children (6 to 59 months) with and without ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 217 ... Browse Title Index. Journal Home > Advanced ... Vol 13, No 1 (2016), Access to specialized surgical care, Abstract PDF. H Saidi ... Vol 9, No 2 (2012), Clinical Assessment of the Palmaris Longus – Accuracy of common tests, Abstract PDF ... Vol 11, No 2 (2014), Clinical trials in Surgery, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 1006 ... Issue, Title. Vol 49, No 8 (2007), Clinical approach to a patient with abnormal uterine bleeding, Abstract PDF. B G Lindeque. Vol 57, No 5 (2015), Clinical evidence in the management of swimmer's ear, Abstract PDF. Andre Marais. Vol 50, No 1 (2008), Clinical features of Systemic Lupus ...

Browse Title Index

African Journals Online (AJOL)

Items 251 - 300 of 2005 ... Issue, Title. Vol 92, No 4 (2015), Blood Pressure and Obesity Index Assessment in a Typical Urban Slum in Enugu, Nigeria, Abstract. GI Ahaneku, CU Osuji, OC Oguejiofor, BC Anisiuba, VO Ikeh, JE Ahaneku. Vol 80, No 10 (2003):, Blood pressure control in a population where antihypertensives are ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 644 ... Issue, Title. Vol 19, No 2 (2007), A qualitative study of medical student socialization in Malawi\\'s College of Medicine: Clincal crisis and beyond, Abstract PDF. C Wendland, C Bandawe. Vol 19, No 2 (2007), A qualitative study of medical student socialization in Malawi\\'s College of Medicine: Preclinical ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 101 ... Issue, Title. Vol 3, No 4 (2014), Chlamydia trachomatis IgG antibodies seroprevalence among students in two tertiary institutions in Anambra state, Nigeria: a comparative study, Abstract PDF. CB Duru, FE Emele, ED Adinma, CO Ifeadike, KA Uwakwe, AO Oluboyo, BO Oluboyo, C Abejegah. Vol 2, No 1 ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 1038 ... Issue, Title. Vol 31, No 2 (2009), Assessing the utility of a continuous, underway fish egg sampler (CUFES) for sampling zooplankton, Abstract. S Sono, CL Moloney, CD van der Lingen. Vol 38, No 4 (2016), Assessing trophic adaptability is critical for understanding the response of predatory fishes to ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 17 (2005), A. C. conduction behaviour in amorphous WO3/CEO2 thin film, Abstract. B Yagoubi, C A Hogarth, A Boukorrt. Vol 16 (2003), A lossless image compression algorithm using variable block size segmentation, Abstract. Z Brahimi, K A Saadi, N Baraka. Vol 15 (2003), Analysis method of wavelet ...

Browse Title Index

African Journals Online (AJOL)

Items 451 - 500 of 1346 ... Issue, Title. Vol 32, No 1 (2015), Fire and the dynamics of two unpalatable grass species (Cymbopogon pospischilii and Elionurus muticus) in a semi-arid climate, Abstract. Hennie A Snyman. Vol 8, No 1 (1973), Fire as a method of controlling macchia (Fynos) vegetation on the Amathole Mountains of ...

Cr(VI) and Cr(III) removal from aqueous solution by raw and modified lignocellulosic materials: a review.

Science.gov (United States)

Miretzky, P; Cirelli, A Fernandez

2010-08-15

In aqueous systems, chromium usually exists in both trivalent and hexavalent oxidation states, being Cr(VI) of particular importance and concern due to its great toxicity. Industrial sources of Cr(VI) are leather tanning, mining of chrome ore, production of steel and alloys, etc. The most common conventional method for Cr(VI) removal is reduction to Cr(III) at pH 2.0 and precipitation of Cr (OH)(3) with lime at pH 9-10. The disadvantage of precipitation is the disposal of the solid waste. Adsorption of Cr by different low cost materials seems to be a suitable choice for wastewater treatment. Many by-products of agriculture have proved to be suitable low cost adsorbents for Cr(VI) and Cr(III) removal from water. Lignocellulosic residues, which include both wood residues and agricultural residues, have adsorption capacity comparable to other natural sorbents, but they have the advantage of very low or no cost, great availability and simple operational process. This study is a review of the recent literature on the use of natural and modified lignocellulosic residues for Cr adsorption. The Cr maximum adsorption capacity and the adsorption mechanism under different experimental conditions are reported when possibly. Copyright 2010 Elsevier B.V. All rights reserved.

Low-field spin dynamics of Cr₇Ni and Cr₇Ni-Cu-Cr₇Ni molecular rings as detected by μsR

OpenAIRE

Sanna, S.; Arosio, P.; Bordonali, L.; Adelnia, F.; Mariani, M.; Garlatti, E.; Baines, C.; Amato, A.; Sabareesh, K. P.V.; Timco, G.; Winpenny, R. E.P.; Blundell, S. J.; Lascialfari, A.

2017-01-01

Muon spin rotation measurements were used to investigate the spin dynamics of heterometallic Cr7Ni and Cr7Ni-Cu-Cr7Ni molecular clusters. In Cr7Ni the magnetic ions are arranged in a quasiplanar ring and interact via an antiferromagnetic exchange coupling constant J, while Cr7Ni-Cu-Cr7Ni is composed of two Cr7Ni linked by a bridging moiety containing one Cu ion, that induces an inter-ring ferromagnetic interaction J ≪ J. The longitudinal muon relaxation rate λ collected at low magnetic fields...

Atomistic simulation of the influence of Cr on the mobility of the edge dislocation in Fe(Cr) alloys

International Nuclear Information System (INIS)

Hafez Haghighat, S.M.; Terentyev, D.; Schaeublin, R.

2011-01-01

In this work Fe-Cr compounds, as model alloys for the ferritic base steels that are considered as main candidates for the structural materials of the future fusion reactors, are studied using molecular dynamics simulations. The Cr or so-called α' precipitates, which are obstacles to dislocations, affect mechanical properties, leading to hardening and loss of ductility. The flow stress to move an edge dislocation in a Cr solid solution in pure Fe is studied as a function of Cr content. The strength of a nanometric Cr precipitate as obstacle to an edge dislocation in pure Fe is investigated as a function of its Cr content. Results show that with increasing Cr content the precipitate obstacle strength increases, with a strong sensitivity to the local atomic order. Temperature induces a monotonic decrease of the flow stress of the Cr solid solution and of the Cr precipitate obstacle strength.

Fabrication and characterization of reference 9Cr and 12Cr-ODS low activation ferritic/martensitic steels

Energy Technology Data Exchange (ETDEWEB)

Muroga, T., E-mail: muroga@nifs.ac.jp [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Nagasaka, T. [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Li, Y.; Abe, H. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Ukai, S. [Graduate School of Engineering, Hokkaido University, N13, W8, Kita-ku, Sapporo 060-8628 (Japan); Kimura, A. [Institute of Advanced Energy, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Okuda, T. [Kobelco Research Institute, 1-5-5 Takatsukadai, Nishi-ku, Kobe, Hyogo 651-2271 (Japan)

2014-10-15

For the purpose of arranging reference alloys available for various characterization efforts by Japanese fusion research groups, fabrication of reference 9Cr and 12Cr-ODS steels have been carried out with similar manufacturing processes followed by various characterizations. The fabrication proceeded with powder mixing, MA, encapsulation into mild steel cases, hot extrusion and hot forging, followed by final heat treatments. Each alloy was extruded into three bars. The characterization included chemical composition analysis, SEM and TEM microstructural observations, hardness tests, tensile tests at RT and 973 K, and relatively short-term thermal creep tests at 973 K. Room temperature hardness for 9Cr-ODS was larger than 12Cr-ODS, the former showing large increase when annealing temperature exceeded 1200 K and the latter showing no significant change with annealing temperature. Tensile strength of 9Cr-ODS was significantly larger than that of 12Cr-ODS at RT but comparable at 973 K. 9Cr-ODS showed longer and shorter creep rupture time than 12Cr-ODS at high and low stress levels, respectively. The mechanism of the difference in creep properties of the two alloys was discussed.

Development of Cr3C2-25(Ni20Cr) nanostructured coatings

International Nuclear Information System (INIS)

Cunha, Cecilio Alvares da

2012-01-01

This study is divided in two parts. The first part is about the preparation of nanostructured Cr 3 C 2 -25(Ni20Cr) powders by high energy milling followed by characterization of the milled and the as received powder. Analyses of some of the data obtained were done using a theoretical approach. The second part of this study is about the preparation and characterization of coatings prepared with the nanostructured as well as the as received Cr 3 C 2 -25(Ni20Cr) powders. The high temperature erosion-oxidation (E-O) behavior of the coatings prepared with the two types of powders has been compared based on a technological approach. The average crystallite size of the Cr 3 C 2 -25(Ni20Cr) powder decreased rapidly from 145 nm to 50 nm in the initial stages of milling and thereafter decreased slowly to a steady state value of around 10 nm with further increase in milling time. This steady state corresponds to the beginning of a dynamic recovery process. The maximum lattice strain (ε = 1,17%) was observed in powders milled for 16 hours, and this powders critical crystallite size was 28 nm. In contrast, the lattice parameter attained a minimum for powders milled for 16 hours. Upon reaching the critical crystallite size, the dislocation density attained a steady state regime and all plastic deformation introduced in the material there after was in the form of events occurring at the grain boundaries, due mainly to grain boundary sliding. The deformation energy stored in the crystal lattice of the Cr 3 C 2 -25(Ni20Cr) powders milled for different times was determined from enthalpy variation measurements. These results indicated that the maximum enthalpy variation (δH = 722 mcal) also occurred for powders milled for 16 hours. In a similar manner, the maximum specific heat variation (δC p = 0,278 cal/gK) occurred for powders milled for 16 hours. The following mechanical properties of Cr 3 C 2 -25(Ni20Cr) coatings prepared using the HVOF thermal spray process were determined

Browse Title Index

African Journals Online (AJOL)

Items 801 - 850 of 11090 ... Issue, Title. Vol 10, No 61 (2011), Analysis of chemical constituents in medicinal plants of selected districts of Pakhtoonkhwa, Pakistan, Abstract PDF. I Hussain, R Ullah, J Khan, N Khan, M Zahoor, N Ullah, MuR Khattak, FA Khan, A Baseer, M Khurram. Vol 10, No 77 (2011), Analysis of chloroplast ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 387 ... Issue, Title. Vol 15, No 2 (2015), Introduction to Christian philosophy, Abstract. Charles Ogundu Nnaji. Vol 8, No 2 (2006), Is Quantum Mechanics a Complete Theory?: A Philosophical Defense of Einstein's Position, Abstract. U O Egbai. Vol 10, No 1 (2007), Jesus in Africa, Abstract. FF Edet. Vol 10, No ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 647 ... Issue, Title. Vol 13, No 2 (2010), 'N toekomstige perspektief op grondwetlike stabiliteit, Abstract PDF. F.W de Klerk. Vol 18, No 5 (2015), Cloete murray and Another v Firstrand bank ltd t/a Wesbank [2015] ZASCA 39A, Abstract PDF. M Laubscher. Vol 15, No 5 (2012), Cave Pecuniam: Lawyers as ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 814 ... Issue, Title. Vol 21, No 2 (2016), A 10 years trend of peptic ulcer disease and other gastrointestinal disorders in northern Uganda, Abstract PDF. T.R. Okello, D.M. Ogwang, I Pecorella. Vol 21, No 2 (2016), A 2-years description of traumatic brain injury admissions in Tikur Anbessa Specialized Hospital ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 319 ... Issue, Title. Vol 23, No 2 (2016), Carica papaya juice enhanced in-vitro cell proliferation better than freeze-dried PBS extract using scratch assay, Abstract. A.B. Nafiu, E Abdulaziz, M.T. Rahman. Vol 23, No 2 (2016), A comparative study of the ownership and utilization of insecticide treated nets in ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 52 ... Issue, Title. Vol 15 (2000), Ammi analysis of maize yield trials in South-Western Nigeria, Abstract. SR Ajibade, BA Ogunbodede. Vol 20 (2006), Association of yield with some agronomic characters in potatoes in a cool mid-altitude location, Abstract. CO Amadi, EE Ene Obong. Vol 20 (2006), Casein (CSN3) ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 249 ... Issue, Title. Vol 10, No 1 (2010), Ye Shakoch Chilot (the court of the sheikhs): A traditional institution of conflict resolution in Oromiya zone of Amhara regional state, Ethiopia, Abstract PDF. M Zeleke. Vol 15, No 3 (2015), A comparative analysis of the Post- Arab Spring National Dialogues in Tunisia and ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 683 ... Issue, Title. Vol 54, No 1 (2006), Bovine tuberculosis survey in urban and peri urban dairy farms in coastal humid region of Tanga, Tanzania, Abstract. ES Swai, G Shirima, S Bwanga, W Moshy. Vol 60, No 3 (2012), Browsing capacity and nutritive value of indigenous browses in a tropical Coastal ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 1215 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... Vol 12, No 1 (2018), Analysis of the effects of frequent strikes on academic performance of students in universities in Nigeria: Edo State as a focal point, Abstract PDF ... Vol 6, No 1 (2012), Appraisal as a Determinant for Adequate ...

Browse Title Index

African Journals Online (AJOL)

Items 251 - 300 of 490 ... Issue, Title. Vol 6, No 2 (2010), Knowledge and patterns of use of highly active antiretroviral therapies in HIV management at Abuja, Nigeria, Abstract. Jill I Okpalugo, US Inyang, K Ibrahim, F Anita, Chinwe V Ukwe, NC Aguwa. Vol 5, No 4 (2009), Knowledge and utilization of the acts in two major ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 14 of 14 ... Issue, Title. Vol 2, No 1 (2009), Auditory and Respiratory Health Disorders Among Workers in an Iron and Steel Factory, Abstract. GM Abdel – Rasoul, OAE Mahrous, ME Abou Salem, MA Al-Batanony, HK Allam. Vol 2, No 1 (2009), Effect of An Educational Program About Medical Waste Management on ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 263 ... Issue, Title. Vol 1, No 2 (2002), Effect of Light and Darkness on Packed Cell Volume in the Rat, Abstract. A. A. OSINUBI, F. I. DURU, C. C. NORONHA, A. O. OKANLAWON. Vol 4, No 1 (2005), Effect of Marijuana Smoking on Blood Chemistry and Serum Biogenic Amines Concentrations in Humans ...

Browse Title Index

African Journals Online (AJOL)

Items 301 - 350 of 745 ... Issue, Title. Vol 9, No 3 (1999), Frequency And Outcome In AIDS Patients In A University Teaching Hospital – A Five Year Review, Abstract. SA Ogun, OO Adelowo, AEA ... Vol 18, No 2 (2008), Good cllinical practice in clinical drug trials - What you need to know, Abstract. K Soyebi, Y Abosede, HAB ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 4119 ... Issue, Title. Vol 86, No 2 (1996), A re-evaluation of isotope screening for skeletal metastases in nodenegative breast cancer, Abstract PDF. C.A. Gudgeon, I.D. Werner, D.M. Dent. Vol 104, No 6 (2014), A reflection on the South African Medical Association – past, present and future, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 351 - 400 of 979 ... Issue, Title. Vol 45, No 9 (2003), Erectile dysfunction: A GP's guide to clinical assessment, Abstract PDF. PJ Harden. Vol 47, No 4 (2005), Ethical Issues in Family Practice: My Culture – Right or Wrong? Abstract PDF. GA Ogunbanjo, D Knapp van Bogaert. Vol 59, No 3 (2017), Ethical issues with ...

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 333 ... Issue, Title. Vol 15, No 1 (2016), Irrigation potential of Inuakpa in Odukpani local government of Cross river using Kostiakov model, Abstract PDF. B.O. Unuigbe, K.I. Ofem, N.R.B. Antigha. Vol 2, No 2 (2003), LABOUR USE IN SMALL-SCALE YAM PRODUCTION IN QUA'AN PAN LOCAL GOVERNMENT ...

Browse Title Index

African Journals Online (AJOL)

Items 701 - 750 of 1010 ... Issue, Title. Vol 6, No 2 (1998), Performance et stabilité de rendement des génotypes de patate douce dans divers environnements à l'est du Congo, Abstract. P Phemba, T Mutombo, N B Lutaladio, E E Carey. Vol 22 (2014): Supplement, Performance of Artemia shell-free embryos, Moina micrura and ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 13, No 2 (2013), Using Mindfulness as a Teaching Aid for Phenomenology, Abstract PDF. IR Owen. Vol 8, No 1 (2008), Were Nietzsche's Cardinal Ideas – Delusions? Abstract PDF. Eva M Cybulska. Vol 12, No 1 (2012), What did you learn in school today? Abstract PDF. Carina Henriksson. Vol 5, No 1 (2005) ...

Browse Title Index

African Journals Online (AJOL)

Items 4351 - 4386 of 4386 ... Issue, Title. Vol 107, No 6 (2017), When students become patients: TB disease among medical undergraduates in Cape Town, South Africa, Abstract PDF. H van der Westhuizen, A Dramowski. Vol 106, No 4 (2016), Where do children die and what are the causes? Under-5 deaths in the Metro West ...

Browse Title Index

African Journals Online (AJOL)

Issue, Title. Vol 10, No 2 (2014), Sorindeia warneckei Engl. (Anacardiaceae), une espèce multi-usagère de la dépression de la Lama au Togo, Abstract PDF. A Akodewou, S Akpavi, M Dourma, K Batawila, KB Amegnaglo, W Atakpama, K Akpagama. Vol 10, No 1 (2014), Sterculia setigera Del.: influence de quelques ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 126 ... Issue, Title. Vol 8, No 2 (2016), 2010 FIFA World Cup stadium investment: Does the post-event usage justify the expenditure? Abstract PDF. Luke Humphrey, Gavin Fraser. Vol 6, No 1 (2014), 7Implication of mergers and acquisitions on stock returns before and during the 2007–2009 credit crunch: An ...

Searching for “LiCrIIPO4”

International Nuclear Information System (INIS)

Mosymow, E.; Glaum, R.; Kremer, R.K.

2014-01-01

The two new phosphates LiCr II 4 (PO 4 ) 3 and Li 5 Cr II 2 Cr III (PO 4 ) 4 are discovered as equilibrium phases (ϑ=800 °C) in the quarternary system Li/Cr/P/O. Their crystal structures have been determined from single-crystal X-ray diffraction data (LiCr II 4 (PO 4 ) 3 : violet-blue, Pnma (no. 62), Z=4, a=6.175(1) Å, b=14.316(3) Å, c=10.277(2) Å, 100 parameters, R 1 =0.028, wR 2 =0.08, 2060 unique reflections with F o >4σ(F o ); Li 5 Cr II 2 Cr III (PO 4 ) 4 : greyish-green, P1 ¯ (no. 2), Z=1, a=4.9379(7) Å, b=7.917(2) Å, c=8.426(2) Å, α=109.98(2)°, β=90.71(1)°, γ=104.91(1)°, 131 parameters, R 1 =0.022, wR 2 =0.067, 1594 unique reflections with F o >4σ(F o )). Li 5 Cr II 2 Cr III (PO 4 ) 4 adopts an hitherto unknown structure type. The crystal structure of LiCr II 4 (PO 4 ) 3 is isotypic to that of NaCd II 4 (PO 4 ) 3 and related to that of the mineral silicocarnotite Ca 5 (PO 4 ) 2 (SiO 4 ). Significant disorder between Li + and Cr 2+ is observed for both crystal structures. The oxidation states assigned to chromium in these two phosphates are in agreement with UV/vis/NIR absorption spectra and magnetic susceptibility data recorded for both compounds. Instead of “LiCr II PO 4 ” mixtures of LiCr II 4 (PO 4 ) 3 , Li 5 Cr II 2 Cr III (PO 4 ) 4 , Cr 2 O 3 , and CrP are observed at equilibrium. Instead of “Li 2 Cr II P 2 O 7 ” four-phase mixtures consisting of Li 9 Cr III 3 (P 2 O 7 ) 3 (PO 4 ) 2 , Li 3 Cr III 2 (PO 4 ) 3 , LiCrP 2 O 7 , and CrP were obtained. - Graphical abstract: Investigations on the equilibrium relations in the system Li/Cr/P/O revealed the two hitherto unknown phosphates Li 5 Cr II 2 Cr III (PO 4 ) 4 and LiCr II 4 (PO 4 ) 3 . They form instead of “LiCr II PO 4 ”. The crystal structures, magnetic behavior and optical spectra of these phosphates are reported. - Highlights: • The two new phosphates Li 5 Cr II 2 Cr III (PO 4 ) 4 and LiCr II 4 (PO 4 ) 3 have been characterized. • Optical spectra and paramagnetism of

48 CFR 32.503-15 - Application of Government title terms.

Science.gov (United States)

2010-10-01

... Application of Government title terms. (a) Property to which the Government obtains title by operation of the... Property; and (2) The termination clauses at 52.249, for termination inventory. (c) The contractor may sell... the scrap disposition. (d) When the title to materials or other inventories is vested in the...

The effect of microstructure and temperature on the oxidation behavior of two-phase Cr-Cr2X (X=Nb,Ta) alloys

International Nuclear Information System (INIS)

Brady, M.P.; Tortorelli, P.F.

1998-01-01

The oxidation behavior of Cr(X) solid solution (Cr ss ) and Cr 2 X Laves phases (X = Nb, Ta) was studied individually and in combination at 950--1,100 C in air. The Cr ss phase was significantly more oxidation resistant than the Cr 2 X Laves phase. At 950 C, two-phase alloys of Cr-Cr 2 Nb and Cr-Cr 2 Ta exhibited in-situ internal oxidation, in which remnants of the Cr 2 X Laves phase were incorporated into a growing chromia scale. At 1,100 C, the Cr-Cr 2 Nb alloys continued to exhibit in-situ internal oxidation, which resulted in extensive O/N penetration into the alloy ahead of the alloy-scale interface and catastrophic failure during cyclic oxidation. IN contrast, the Cr-Cr 2 Ta alloys exhibited a transition to selective Cr oxidation and the formation of a continuous chromia scale. The oxidation mechanism is interpreted in terms of multiphase oxidation theory

20 CFR 411.552 - What effect will the subsequent entitlement to title II benefits have on EN payments for title...

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false What effect will the subsequent entitlement to title II benefits have on EN payments for title XVI beneficiaries after they assign their ticket? 411.552 Section 411.552 Employees' Benefits SOCIAL SECURITY ADMINISTRATION THE TICKET TO WORK AND SELF...

Determination of Cr(VI) in wood specimen: A XANES study at the Cr K edge

International Nuclear Information System (INIS)

Strub, E.; Plarre, R.; Radtke, M.; Reinholz, U.; Riesemeier, H.; Schoknecht, U.; Urban, K.; Juengel, P.

2008-01-01

The content of chromium in different oxidation states in chromium-treated wood was studied with XANES (X-ray absorption near-edge structure) measurements at the Cr K absorption edge. It could be shown that wood samples treated with Cr(VI) (pine and beech) did still contain a measurable content of Cr(VI) after four weeks conditioning. If such wood samples were heat exposed for 2 h with 135 deg. C prior conditioning, Cr(VI) was no longer detected by XANES, indicating a complete reduction to chromium (III)

Development of the dentistry alloy Ni-Cr-Nb; Desenvolvimento de ligas odontologicas Ni-Cr-Nb

Energy Technology Data Exchange (ETDEWEB)

Souza, M.A.; Ramos, A.S.; Hashimoto, T.M., E-mail: mari_sou@hotmail.co [UNESP/FEG, Guaratingueta, SP (Brazil). Fac. de Engenharia. Dept. de Materiais e Tecnologia

2010-07-01

This work reports on the structural characterization of Ni-Cr-Mo and Ni-Cr-Nb alloys produced by arc melting. Samples were characterized by means of optical microscopy, X-ray diffraction, scanning electron microscopy, and EDS analysis. Results indicated that the arc melting process was efficient to produce homogeneous structures in Ni-Cr-Mo and Ni-Cr-Nb alloys. The nickel dissolved large amounts of Cr, Mo and Nb, which was detected by EDS analysis and X-ray diffraction. The alloy containing molybdenum indicated the presence of structure based on Ni{sub SS}, while that the alloys containing niobium presented primary grains of Ni{sub SS} and precipitates formed by the simultaneous transformation of the Ni and Ni{sub 3}Nb phases. (author)

Oxidation resistance of CrN/(Cr,V)N hard coatings deposited by DC magnetron sputtering

Energy Technology Data Exchange (ETDEWEB)

Panjan, P., E-mail: peter.panjan@ijs.si [Jožef Stefan Institute, Jamova 39, 1000 Ljubljana (Slovenia); Drnovšek, A.; Kovač, J.; Gselman, P. [Jožef Stefan Institute, Jamova 39, 1000 Ljubljana (Slovenia); Bončina, T. [University of Maribor, Faculty of Mechanical Engineering, Smetanova 17, 2000 Maribor (Slovenia); Paskvale, S.; Čekada, M.; Kek Merl, D.; Panjan, M. [Jožef Stefan Institute, Jamova 39, 1000 Ljubljana (Slovenia)

2015-09-30

In recent years vanadium-doped hard coatings have become available as possible candidates for self-lubrication at high temperatures. Their low coefficient of friction has mainly been attributed to the formation of the V{sub 2}O{sub 5} phase. However, the formation of vanadium oxides must be controlled by the out-diffusion of vanadium in order to achieve the combination of a low coefficient of friction and good mechanical properties for the protective coatings. In this work the application of a nanolayer of CrN/(Cr,V)N hard coating was proposed as a way to better control the out-diffusion of vanadium, while the topmost chromium oxide layer acts as barrier for the vanadium diffusion. However, the aim of this investigation was not only to focus on the formation of the oxide layer. Special attention was given to the oxidation process that takes place at the growth defects, where we observed a strong diffusion of vanadium taking place. The CrN/(Cr,V)N nanolayer coatings were deposited by DC unbalanced magnetron sputtering in an CC800/9 (CemeCon) industrial unit. The vanadium concentration in the (Cr,V)N layers was varied in the range 1.0–11.5 at.%. - Highlights: • Oxidation processes of CrN/(Cr,V)N nanolayers with vanadium content were investigated. • The CrN/(Cr,V)N hard layers were oxidized at high temperature in O2 atm. • The top chromium oxide layer acts as a diffusion barrier for vanadium ions during oxidation. • Important role of growth defects during the oxidation process is demonstrated.

Oxidation resistance of CrN/(Cr,V)N hard coatings deposited by DC magnetron sputtering

International Nuclear Information System (INIS)

Panjan, P.; Drnovšek, A.; Kovač, J.; Gselman, P.; Bončina, T.; Paskvale, S.; Čekada, M.; Kek Merl, D.; Panjan, M.

2015-01-01

In recent years vanadium-doped hard coatings have become available as possible candidates for self-lubrication at high temperatures. Their low coefficient of friction has mainly been attributed to the formation of the V_2O_5 phase. However, the formation of vanadium oxides must be controlled by the out-diffusion of vanadium in order to achieve the combination of a low coefficient of friction and good mechanical properties for the protective coatings. In this work the application of a nanolayer of CrN/(Cr,V)N hard coating was proposed as a way to better control the out-diffusion of vanadium, while the topmost chromium oxide layer acts as barrier for the vanadium diffusion. However, the aim of this investigation was not only to focus on the formation of the oxide layer. Special attention was given to the oxidation process that takes place at the growth defects, where we observed a strong diffusion of vanadium taking place. The CrN/(Cr,V)N nanolayer coatings were deposited by DC unbalanced magnetron sputtering in an CC800/9 (CemeCon) industrial unit. The vanadium concentration in the (Cr,V)N layers was varied in the range 1.0–11.5 at.%. - Highlights: • Oxidation processes of CrN/(Cr,V)N nanolayers with vanadium content were investigated. • The CrN/(Cr,V)N hard layers were oxidized at high temperature in O2 atm. • The top chromium oxide layer acts as a diffusion barrier for vanadium ions during oxidation. • Important role of growth defects during the oxidation process is demonstrated.

A crítica feminista na mira da crítica A crítica feminista na mira da crítica

Directory of Open Access Journals (Sweden)

Rita Terezinha Schmidt

2008-04-01

Full Text Available This essay presents a dialogue with some texts that appeared in an anthology of critical writings about “Brazilian feminisms,” problematizing them and thus providing a productive discussion about the production of knowledge about and by feminist criticism in Brazil. Este artigo apresenta um diálogo com textos presentes em uma antologia crítica sobre “feminismos brasileiros”, problematizando-os e, por conseguinte, gerando uma discussão produtiva acerca da produção de conhecimento sobre e pela crítica feminista no Brasil.

Is CR39 worth the effort?

International Nuclear Information System (INIS)

Griffith, R.V.

1987-01-01

CR39 proton sensitive track detectors were greeted by the radiation protection community at the end of the last decade as a major breakthrough for personnel neutron dosimetry. A number of laboratories eagerly began research on application of CR39 to their dosimetry needs. However, in the last two or three years the enthusiasm has subsided, and many health physicists have stopped working with the material. The number of participants using CR39 in the Oak Ridge National Laboratory Personnel Intercomparison Studies dropped from six in 1985 to three in 1986. On a national level, the Federal Republic of Germany with researchers active in CR39 research recently adopted an albedo system as their national standard. In contrast, the United States Department of Energy (DOE) is supporting development of a CR39 based combination dosimeter to meet Department wide dosimetry needs. The English National Radiological Protection Board (NRPB) now features the use of CR39 in the NRPB PADC(CR39). There has obviously been a range of experiences with CR39 in the dosimetry community. Why has this been the case, and what is the proper role for CR39 in personnel neutron dosimetry. 12 refs., 2 figs., 1 tab

Matrix of Title V-Related And Air Grant-Eligible Activities

Science.gov (United States)

This document may be of assistance in applying the Title V air operating permit regulations. This document is part of the Title V Policy and Guidance Database available at www2.epa.gov/title-v-operating-permits/title-v-operating-permit-policy-and-guidance-document-index. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Electronic and magnetic properties of SmCrSb3 and GdCrSb3: A first principles study

International Nuclear Information System (INIS)

Sandeep; Ghimire, M.P.; Thapa, R.K.

2011-01-01

The density of states (DOS) and the magnetic moments of SmCrSb 3 and GdCrSb 3 have been studied by first principles full-potential linearized augmented plane wave (FP-LAPW) method based on density functional theory (DFT). For the exchange-correlation potential, the local-spin density approximations with correlation energy (LSDA+U) method have been used. Total and partial DOS have been computed using the WIEN2k code. DOS result shows the exchange-splittings of Cr-3d and rare-earth (R) 4f states electrons, which are responsible for the ground state ferromagnetic (FM) behavior of the systems. The FM behavior of these systems is strongly influenced by the average number of Cr-3d and Sm (Gd) 4f-electrons. The effective moment of SmCrSb 3 is found to be 7.07 μ B while for GdCrSb 3 it is 8.27 μ B . The Cr atom plays a significant role on the magnetic properties due to the hybridization between Cr-3d and Sb-5p states. - Highlights: → DOS and the magnetic moments of SmCrSb 3 and GdCrSb 3 are studied by full-FP-LAPW method. → Exchange splitting of eg and t2g of Cr-3d states and the rare-earth 4f state electrons are responsible for ground state ferromagnetism. → Rare-earth magnetic moments are greater than Cr moment indicating presence of 4f states.

HFO operation with CR injection

Energy Technology Data Exchange (ETDEWEB)

Poensgen, Christian [MAN-Diesel und Turbo SE, Augsburg (Germany)

2011-07-01

In 1996 MAN Diesel and Turbo SE started the development of a CR-system for medium speed engines for HFO operation up to fuel viscosity of 700 cSt. 2004 the first field test engine, a 7L 32/40 GenSet was put into service as a retrofit and collected up to now more than 20.000 running hours operated on HFO on a large container vessel. Meanwhile several L32/40 CR GenSets, L32/44 CR, V48/60 CR and L21/31 CR engines collected more than 100000 running hours in HFO operation before MAN Diesel started up the serial production of the new 32/44 CR and 48/60 CR engines. All of these engines are still in service. The paper will give an overview about the field experience and countermeasures which were necessary to develop a reliable product which fulfills the customers' demands concerning low fuel oil consumption, invisible smoke over the whole load range, low emission levels and maintenance costs. The experience was made in a wide range of applications such as GenSet, Cruise Vessel main propulsion and ferry main propulsion running 24h/day. The field test engines reached an availability of more than 90% per year. The paper also will point out the win/win situation for the the manufacturer and customer to participate in the development of the CR technology. For customers satisfaction MAN Diesel provides help for easy handling like online access per satellite connection, easy leakage detection and operator training at site or at the new built academies. The flexibility of the CR-system is the base frame for the future development of engines which fulfills IMO TIER II and IMO TIER III with high efficiency. The necessary reliability, a must, has been proven in the field under real conditions. (orig.)

Modelling of functionally graded materials by numerical homogenization

Energy Technology Data Exchange (ETDEWEB)

Schmauder, S.; Weber, U. [Stuttgart Univ. (Germany). Staatliche Materialpruefungsanstalt

2001-03-01

In this contribution, the mechanical behaviour of different ZrO{sub 2}/NiCr 80 20 compositions is analysed and compared with experimental findings. The microwave-sintered material is found to possess a slightly dominant ceramic matrix for intermediate volume fractions. Its thermal expansion coefficient deviates from the rule of mixture. The modulus and the stress strain behaviour can be simulated by a numerical homogenization procedure, and the influence of residual stresses is found to be negligible. A newly introduced parameter (matricity) describes the mutual circumvention of the phases and is found to strongly control the stress level of the composite, globally as well as locally. Finally, a graded component and a metal/ceramic bi-material are compared for thermal as well as mechanical loading. (orig.)

Complex analysis and CR geometry

CERN Document Server

Zampieri, Giuseppe

2008-01-01

Cauchy-Riemann (CR) geometry is the study of manifolds equipped with a system of CR-type equations. Compared to the early days when the purpose of CR geometry was to supply tools for the analysis of the existence and regularity of solutions to the \\bar\\partial-Neumann problem, it has rapidly acquired a life of its own and has became an important topic in differential geometry and the study of non-linear partial differential equations. A full understanding of modern CR geometry requires knowledge of various topics such as real/complex differential and symplectic geometry, foliation theory, the geometric theory of PDE's, and microlocal analysis. Nowadays, the subject of CR geometry is very rich in results, and the amount of material required to reach competence is daunting to graduate students who wish to learn it. However, the present book does not aim at introducing all the topics of current interest in CR geometry. Instead, an attempt is made to be friendly to the novice by moving, in a fairly relaxed way, f...

Title XX and CETA. A Coordination Guide for Title XX Administrators.

Science.gov (United States)

Urban Management Consultants of San Francisco, Inc., CA.

Written for the social service (Title XX) administrator at the State or sub-State level, this guide is intended to serve four major purposes: (1) Provide selected insights into what the Comprehensive Employment and Training Act (CETA) is and how it works; (2) point out potential areas for coordination which, from study or field experience, hold…

Biosorption of Cr(VI) by coconut coir: Spectroscopic investigation on the reaction mechanism of Cr(VI) with lignocellulosic material

International Nuclear Information System (INIS)

Shen, Ying-Shuian; Wang, Shan-Li; Huang, Shiuh-Tsuen; Tzou, Yu-Min; Huang, Jang-Hung

2010-01-01

In this study, the removal mechanism of Cr(VI) from water by coconut coir (CC) was investigated using X-ray photoelectron spectroscopy (XPS), Cr K-edge X-ray absorption near edge structure (XANES) and FTIR spectroscopy. The results showed that, upon reaction with CC at pH 3, Cr(VI) was reduced to Cr(III), which was either bound to CC or released back into solution. As revealed by the FTIR spectra of CC before and after reacting with Cr(VI), the phenolic methoxyl and hydroxyl groups of lignin in CC are the dominant drivers of Cr(VI) reduction, giving rise to carbonyl and carboxyl groups on CC. These functional groups can subsequently provide binding sites for Cr(III) resulting from Cr(VI) reduction. In conjunction with forming complexes with carbonyl and carboxyl groups, the formation of Cr(III) hydroxide precipitate could also readily occur as revealed by the linear combination fitting of the Cr K-edge XANES spectrum using a set of reference compounds. The phenolic groups in lignin are responsible for initiating Cr(VI) reduction, so lignocellulosic materials containing a higher amount of phenolic groups are expected to be more effective scavengers for removal of Cr(VI) from the environment.

Biosorption of Cr(VI) by coconut coir: Spectroscopic investigation on the reaction mechanism of Cr(VI) with lignocellulosic material

Energy Technology Data Exchange (ETDEWEB)

Shen, Ying-Shuian [Department of Soil and Environmental Sciences, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 40227, Taiwan (China); Wang, Shan-Li, E-mail: slwang@nchu.edu.tw [Department of Soil and Environmental Sciences, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 40227, Taiwan (China); Huang, Shiuh-Tsuen [Department of Soil and Environmental Sciences, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 40227, Taiwan (China); Department of Science Application and Dissemination, National Taichung University, Taichung, Taiwan (China); Tzou, Yu-Min; Huang, Jang-Hung [Department of Soil and Environmental Sciences, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 40227, Taiwan (China)

2010-07-15

In this study, the removal mechanism of Cr(VI) from water by coconut coir (CC) was investigated using X-ray photoelectron spectroscopy (XPS), Cr K-edge X-ray absorption near edge structure (XANES) and FTIR spectroscopy. The results showed that, upon reaction with CC at pH 3, Cr(VI) was reduced to Cr(III), which was either bound to CC or released back into solution. As revealed by the FTIR spectra of CC before and after reacting with Cr(VI), the phenolic methoxyl and hydroxyl groups of lignin in CC are the dominant drivers of Cr(VI) reduction, giving rise to carbonyl and carboxyl groups on CC. These functional groups can subsequently provide binding sites for Cr(III) resulting from Cr(VI) reduction. In conjunction with forming complexes with carbonyl and carboxyl groups, the formation of Cr(III) hydroxide precipitate could also readily occur as revealed by the linear combination fitting of the Cr K-edge XANES spectrum using a set of reference compounds. The phenolic groups in lignin are responsible for initiating Cr(VI) reduction, so lignocellulosic materials containing a higher amount of phenolic groups are expected to be more effective scavengers for removal of Cr(VI) from the environment.

Biosorption of Cr(VI) by coconut coir: spectroscopic investigation on the reaction mechanism of Cr(VI) with lignocellulosic material.

Science.gov (United States)

Shen, Ying-Shuian; Wang, Shan-Li; Huang, Shiuh-Tsuen; Tzou, Yu-Min; Huang, Jang-Hung

2010-07-15

In this study, the removal mechanism of Cr(VI) from water by coconut coir (CC) was investigated using X-ray photoelectron spectroscopy (XPS), Cr K-edge X-ray absorption near edge structure (XANES) and FTIR spectroscopy. The results showed that, upon reaction with CC at pH 3, Cr(VI) was reduced to Cr(III), which was either bound to CC or released back into solution. As revealed by the FTIR spectra of CC before and after reacting with Cr(VI), the phenolic methoxyl and hydroxyl groups of lignin in CC are the dominant drivers of Cr(VI) reduction, giving rise to carbonyl and carboxyl groups on CC. These functional groups can subsequently provide binding sites for Cr(III) resulting from Cr(VI) reduction. In conjunction with forming complexes with carbonyl and carboxyl groups, the formation of Cr(III) hydroxide precipitate could also readily occur as revealed by the linear combination fitting of the Cr K-edge XANES spectrum using a set of reference compounds. The phenolic groups in lignin are responsible for initiating Cr(VI) reduction, so lignocellulosic materials containing a higher amount of phenolic groups are expected to be more effective scavengers for removal of Cr(VI) from the environment. 2010 Elsevier B.V. All rights reserved.

Electrochemical Behavior and Hydrophobic Properties of CrN and CrNiN Coatings in Simulated Proton Exchange Membrane Fuel Cell Environment

Directory of Open Access Journals (Sweden)

JIN Jie

2016-10-01

Full Text Available The CrN and CrNiN coatings were prepared on the surface of 304 stainless steel by closed field unbalanced magnetron sputtering.X ray diffraction and field emission scanning electron microscopy were used to characterize the structure and morphology of the coatings.The electrochemical corrosion properties under the simulated proton exchange membrane fuel cell(PEMFC environment, interfacial contact resistance and hydrophobic properties of the two kinds of different coatings were investigated by electrochemical methods,contact resistance test and hydrophobic test,respectively.The results indicate that CrN coating mainly consists of CrN and Cr2N phase,CrN and Cr2N phases in the CrNiN coating are less compared to CrN film, and Ni exist as element in CrNiN coating; dynamic polarization tests show the coating is of better corrosion resistance,whereas the corrosion resistance of CrNiN coating is worse than that of CrN coating,constant potential polarization test shows the corrosion current density of CrN and CrNiN coatings are equivalent; CrN and CrNiN coatings significantly reduce the interfacial contact resistance of the 304 stainless steel,among which CrN coating has the smallest contact resistance; and CrNiN coating which has better hydrophobicity than that of CrN coating is more beneficial for the water management in proton exchange membrane fuel cell.

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 327 ... Issue, Title. Vol 10, No 4 (2016), Omphalocoeles: A decade in review, Abstract PDF. S Singh, A Madaree. Vol 2, No 4 (2008), Ortner syndrome, Abstract PDF. E Meyer, NE Jones, LJ Zühlke. Vol 10, No 3 (2016), Outcome of children admitted to a general highcare unit in a regional hospital in the ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 412 ... Issue, Title. Vol 32, No 2 (2013), Seinsverständnis and meaning in Heidegger, Abstract. Rafael Winkler. Vol 21, No 3 (2002), A defense of peace as a human right, Abstract. Patrick Hayden. Vol 26, No 2 (2007), A Kantian stance on teleology in biology, Abstract. AA Cohen. Vol 30, No 1 (2011), A Likely ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 286 ... Issue, Title. Vol 2, No 3-4 (2008), Impact of fire wood collection on trees species diversity in Bauchi state, Nigeria, Abstract. A Nura, A Ibrahim, I Mohammed, U Haruna. Vol 5, No 3 (2011), Impact of national special program for food security in Abia State, nigeria, Abstract. CO Emerole. Vol 5, No 1 (2011) ...

24 CFR 200.61 - Title.

Science.gov (United States)

2010-04-01

... Commissioner. (c) Endorsement of the credit instrument for insurance shall evidence the acceptability of title... GENERAL INTRODUCTION TO FHA PROGRAMS Requirements for Application, Commitment, and Endorsement Generally...

Energy Information Data Base: serial titles

International Nuclear Information System (INIS)

1980-06-01

The Department of Energy Technical Information Center (TIC) is responsible for creating bibliographic data bases that are used in the announcement and retrieval of publications dealing with all phases of energy. The TIC interactive information processing system makes use of a number of computerized authorities so that consistency can be maintained and indexes can be produced. One such authority is the Energy Information Data Base: Serial Titles. This authority contains the full and abbreviated journal title, country of publication, CODEN, and certain codes. This revision replaces previous revisions of this document

Wear resistance of nano- and micro-crystalline diamond coatings onto WC-Co with Cr/CrN interlayers

Energy Technology Data Exchange (ETDEWEB)

Polini, Riccardo [Dipartimento di Scienze e Tecnologie Chimiche, Universita di Roma Tor Vergata, Via della Ricerca Scientifica, 1, Rome, 00133 (Italy); Barletta, Massimiliano, E-mail: barletta@ing.uniroma2.i [Dipartimento di Ingegneria Meccanica, Universita di Roma Tor Vergata, Via del Politecnico, 1, Rome, 00133 (Italy); Cristofanilli, Giacomo [Dipartimento di Scienze e Tecnologie Chimiche, Universita di Roma Tor Vergata, Via della Ricerca Scientifica, 1, Rome, 00133 (Italy)

2010-12-30

Cr/CrN bi-layers have been used recently to promote the growth of high quality Hot Filament Chemical Vapour Deposition (HFCVD) diamond coatings onto Co-cemented tungsten carbide (WC-6 wt.%Co) substrates. In the present investigation, the influence of the crystalline size of the diamond coatings on their wear endurance is looked into. Nano- (NDC) and micro-crystalline Diamond Coatings (MDC) were deposited by HFCVD onto untreated and Fluidized Bed (FB) treated Cr/CrN interlayers. NDCs, characterized by a cauliflower-like morphology, showed improved wear resistance. However, the superimposition of NDCs onto Cr/CrN interlayers micro-corrugated by FB treatment was found to be the most promising choice, leading to the formation of highly adherent and wear resistant coatings.

Development of Cr{sub 3}C{sub 2}-25(Ni20Cr) nanostructured coatings; Desenvolvimento de revestimentos nanostruturados de Cr{sub 3}C{sub 2}-25(Ni20Cr)

Energy Technology Data Exchange (ETDEWEB)

Cunha, Cecilio Alvares da

2012-07-01

This study is divided in two parts. The first part is about the preparation of nanostructured Cr{sub 3}C{sub 2}-25(Ni20Cr) powders by high energy milling followed by characterization of the milled and the as received powder. Analyses of some of the data obtained were done using a theoretical approach. The second part of this study is about the preparation and characterization of coatings prepared with the nanostructured as well as the as received Cr{sub 3}C{sub 2}-25(Ni20Cr) powders. The high temperature erosion-oxidation (E-O) behavior of the coatings prepared with the two types of powders has been compared based on a technological approach. The average crystallite size of the Cr{sub 3}C{sub 2}-25(Ni20Cr) powder decreased rapidly from 145 nm to 50 nm in the initial stages of milling and thereafter decreased slowly to a steady state value of around 10 nm with further increase in milling time. This steady state corresponds to the beginning of a dynamic recovery process. The maximum lattice strain ({epsilon} = 1,17%) was observed in powders milled for 16 hours, and this powders critical crystallite size was 28 nm. In contrast, the lattice parameter attained a minimum for powders milled for 16 hours. Upon reaching the critical crystallite size, the dislocation density attained a steady state regime and all plastic deformation introduced in the material there after was in the form of events occurring at the grain boundaries, due mainly to grain boundary sliding. The deformation energy stored in the crystal lattice of the Cr{sub 3}C{sub 2}-25(Ni20Cr) powders milled for different times was determined from enthalpy variation measurements. These results indicated that the maximum enthalpy variation ({delta}H = 722 mcal) also occurred for powders milled for 16 hours. In a similar manner, the maximum specific heat variation ({delta}C{sub p} = 0,278 cal/gK) occurred for powders milled for 16 hours. The following mechanical properties of Cr{sub 3}C{sub 2}-25(Ni20Cr) coatings

Impact behavior of 9-Cr and 12-Cr ferritic steels after low-temperature irradiation

International Nuclear Information System (INIS)

Klueh, R.L.; Vitek, J.M.; Corwin, W.R.; Alexander, D.J.

1987-01-01

Miniature Charpy impact specimens of 9Cr-1MoVNb and 12Cr-1MoVW steels and these steels with 1 and 2% Ni were irradiated in the High-Flux Isotope Reactor (HFIR) at 50 0 C to displacement damage levels of up to 9 dpa. Nickel was added to study the effect of transmutation helium. Irradiation caused an increase in the ductile-brittle transition temperature (DBTT). The 9Cr-1MoVNb steels, with and without nickel, showed a larger shift than the 12Cr-1MoVW steels, with and without nickel. The results indicated that helium also increased the DBTT. The same steels were previously irradiated at higher temperatures. From the present and past tests, the effect of irradiation temperature on the DBTT behavior can be evaluated. For the 9Cr-1MoVNb steel, there is a continuous decrease in the magnitude of the DBTT increase up to an irradiation temperature of about 400 0 C, after which the shift drops rapidly to zero at about 450 0 C. The DBTT of the 12Cr-1MoVW steel shows a maximum increase at an irradiation temperature of about 400 0 C and less of an increase at either higher or lower irradiation temperatures

Title V Permitting Statistics Inventory

Data.gov (United States)

U.S. Environmental Protection Agency — The Title V Permitting Statistics Inventory contains measured and estimated nationwide statistical data, consisting of counts of permitted sources, types of permits...

PENGAMBILAN LOGAM CR6+ DAN CR TOTAL DARI LIMBAH INDUSTRI ELEKTROPLATING SECARA ELEKTROKOGULASI

Directory of Open Access Journals (Sweden)

Muhammad Nizar Pahlevi

2012-10-01

Full Text Available Electroplating industry is a metal coating industry by way of metal precipitate coatings on metal or plastic which is done so that the electrolytic waste containing heavy metals. Electrocoagulation is a process of merging clumps resulting from the flux of electrical current (DC for the extraction of metal compounds contained in wastewater. In this process of reduction and oxidation reactions occur. Where the metal is reduced and the positive electrode (Al will be oxidized to (Al (OH 3 which serves as a coagulant. The purpose of this research to study methods of electrocoagulation using aluminum electrodes and the influence of the length of time stirring and stirring speed of decision-CR6+ levels and total Cr. This electrocoagulation electroplating wastewater with electricity so that the ions are absorbed by the coagulant in waste binder in the release of the electrode and causes the bond between the metal ions with coagulant. Variation of stirrer speed of 200, 400 and 600 rpm, whereas the long stirring time 25, 50 and 75 minutes. Based on test results, after an analysis showed a significant reduction of the levels of total CR6 + and Cr in the electroplating wastes. CR6+ to obtain a decrease of 95.1% at minute 50 and the stirrer speed of 200 rpm, whereas the total Cr obtained a decrease of 82.69% at minute 75 and a stirrer speed of 600 rpm.

8 ỌZỌ TITLE: THE IGBOMAN'S ARISTOCRATIC INSTITUTION ...

African Journals Online (AJOL)

But money may not be the problem of all the people who are yet to take titles. Some may not like ... Stage One: Payment - In this, the intending ọzọ title holder pays a little sum of money to the alliance group in ..... Orji, M. O. (1999). The History ...

Teacher qualification and the achievement gap in early primary grades.

Directory of Open Access Journals (Sweden)

Donald Easton-Brooks

2009-08-01

Full Text Available Title I of the No Child Left Behind Act (P.L. 107-110, 115 Stat. 1245, 2002 holds schools accountable for reducing the academic achievement gap between the different ethnic groups and requires elementary school teachers to have at least a bachelors degree and a state certification. The purpose of this study was to examine the relationship of the qualification requirement of NCLB to the goal of reducing the academic achievement gap. The study found that students with a certified teacher for most of their early school experience scored higher in reading than students who did not have a certified teacher. In addition, certification was associated with slightly narrowing the academic gap between African American and European American students across early elementary grades.

Microbial conversion of Cr (VI) in to Cr (III) in industrial effluent ...

African Journals Online (AJOL)

These bacterial strains also take up and reduce Cr (VI) present in industrial effluents, and their reduction potential was not significantly affected in the presence of different metallic salts. Key Words: Cr (VI) reduction, bacteria, industrial effluent, heavy metals. African Journal of Biotechnology Vol.3(11) 2004: 610-617 ...

Fast determination of impurities in metallurgical grade silicon for photovoltaics by instrumental neutron activation analysis

International Nuclear Information System (INIS)

Hampel, J.; Boldt, F.M.; Gerstenberg, H.; Hampel, G.; Kratz, J.V.; Reber, S.; Wiehl, N.

2011-01-01

Standard wafer solar cells are made of near-semiconductor quality silicon. This high quality material makes up a significant part of the total costs of a solar module. Therefore, new concepts with less expensive so called solar grade silicon directly based on physiochemically upgraded metallurgical grade silicon are investigated. Metallurgical grade silicon contains large amounts of impurities, mainly transition metals like Fe, Cr, Mn, and Co, which degrade the minority carrier lifetime and thus the solar cell efficiency. A major reduction of the transition metal content occurs during the unidirectional crystallization due to the low segregation coefficient between the solid and liquid phase. A further reduction of the impurity level has to be done by gettering procedures applied to the silicon wafers. The efficiency of such cleaning procedures of metallurgical grade silicon is studied by instrumental neutron activation analysis (INAA). Small sized silicon wafers of approximately 200 mg with and without gettering step were analyzed. To accelerate the detection of transition metals in a crystallized silicon ingot, experiments of scanning whole vertical silicon columns with a diameter of approximately 1 cm by gamma spectroscopy were carried out. It was demonstrated that impurity profiles can be obtained in a comparably short time. Relatively constant transition metal ratios were found throughout an entire silicon ingot. This led to the conclusion that the determination of several metal profiles might be possible by the detection of only one 'leading element'. As the determination of Mn in silicon can be done quite fast compared to elements like Fe, Cr, and Co, it could be used as a rough marker for the overall metal concentration level. Thus, a fast way to determine impurities in photovoltaic silicon material is demonstrated. - Highlights: → We demonstrate a fast way to determine impurities in photovoltaic silicon by NAA. → We make first experiments of locally

27 CFR 46.205 - Guidelines to determine title to articles in transit.

Science.gov (United States)

2010-04-01

... title to articles in transit. 46.205 Section 46.205 Alcohol, Tobacco Products and Firearms ALCOHOL AND... determine title to articles in transit. The dealer may use the following guidelines to establish who holds title to articles in transit. (a) If State law mandates the change in title, then no agreement or...

The Translation of Films: Sub-Titling versus Dubbing

Science.gov (United States)

Voge, Hans

1977-01-01

A study of film translation. Well-documented opinions are given on the advantages and disadvantages of both dubbing and sub-titling. One of the tentative conclusions is that sub-titling is to be preferred because it preserves the original dialogue and allows the audience verying degrees of comprehension. A bibliography is provided. (AMH)

Microstructure, mechanical and tribological characterization of CrN/DLC/Cr-DLC multilayer coating with improved adhesive wear resistance

Science.gov (United States)

Sui, Xudong; Liu, Jinyu; Zhang, Shuaituo; Yang, Jun; Hao, Junying

2018-05-01

Adhesive wear is one of the major reasons for the failure of components during various tribological application, especially for rubbing with viscous materials. This study presents CrN/DLC/Cr-DLC multilayer composite coatings prepared on a plasma enhanced chemical vapor deposition (PECVD) device with the close field unbalanced magnetron sputtering ion plating (CFUBMSIP) technique. SEM, XRD and Raman spectroscopy were used to determine the structure of multilayer coatings. It was found that the multilayer coatings are composed by the alternating CrN and DLC layers. Compared with the single CrN coatings, the friction coefficient of the CrN/DLC/Cr-DLC multilayer coating decreases about more than seven times after sliding a distance of 500 m. This helps to reduce the adhesive wear of multilayer coatings. Compared with the single CrN and DLC coating, the wear rate of the CrN/DLC/Cr-DLC multilayer coating is reduced by an order of magnitude to 7.10 × 10-17 (sliding with AISI 440C) and 2.64 × 10-17 (sliding with TC4) m3/(N m). The improved tribological performance of multilayer coatings mainly attributes to the introduction of lubricant DLC and hard support CrN layers, the enhancement of crack propagation inhibition, and the increment of elastic recovery value We (71.49%) by multilayer design method.

Different roles of ROS and Nrf2 in Cr(VI)-induced inflammatory responses in normal and Cr(VI)-transformed cells

Energy Technology Data Exchange (ETDEWEB)

Roy, Ram Vinod; Pratheeshkumar, Poyil; Son, Yong-Ok; Wang, Lei [Center for Research on Environmental Disease, University of Kentucky, 1095 VA Drive, Lexington, KY 40536 (United States); Department of Toxicology and Cancer Biology, College of Medicine, University of Kentucky, 1095 VA Drive, Lexington, KY 40536 (United States); Hitron, John Andrew [Center for Research on Environmental Disease, University of Kentucky, 1095 VA Drive, Lexington, KY 40536 (United States); Divya, Sasidharan Padmaja; Zhang, Zhuo [Department of Toxicology and Cancer Biology, College of Medicine, University of Kentucky, 1095 VA Drive, Lexington, KY 40536 (United States); Shi, Xianglin, E-mail: xshi5@email.uky.edu [Center for Research on Environmental Disease, University of Kentucky, 1095 VA Drive, Lexington, KY 40536 (United States)

2016-09-15

Hexavalent chromium (Cr(VI)) is classified as a human carcinogen. Cr(VI) has been associated with adenocarcinomas and squamous cell carcinoma of the lung. The present study shows that acute Cr(VI) treatment in human bronchial epithelial cells (BEAS-2B) increased inflammatory responses (TNF-α, COX-2, and NF-кB/p65) and expression of Nrf2. Cr(VI)-induced generation of reactive oxygen species (ROS) are responsible for increased inflammation. Despite the fact that Nrf2 is a master regulator of response to oxidative stress, silencing of Nrf2 in the acute Cr(VI) treatment had no effect on Cr(VI)-induced inflammation. In contrast, in Cr(VI)-transformed (CrT) cells, Nrf2 is constitutively activated. Knock-down of this protein resulted in decreased inflammation, while silencing of SOD2 and CAT had no effect in the expression of these inflammatory proteins. Results obtained from the knock-down of Nrf2 in CrT cells are very different from the results obtained in the acute Cr(VI) treatment. In BEAS-2B cells, knock-down of Nrf2 had no effect in the inflammation levels, while in CrT cells a decrease in the expression of inflammation markers was observed. These results indicate that before transformation, ROS plays a critical role while Nrf2 not in Cr(VI)-induced inflammation, whereas after transformation (CrT cells), Nrf2 is constitutively activated and this protein maintains inflammation while ROS not. Constitutively high levels of Nrf2 in CrT binds to the promoter regions of COX-2 and TNF-α, leading to increased inflammation. Collectively, our results demonstrate that before cell transformation ROS are important in Cr(VI)-induced inflammation and after transformation a constitutively high level of Nrf2 is important. - Highlights: • Cr(VI)-induced ROS increased inflammation, while Nrf2 had no effect. • In the CrT cells knock-down of Nrf2 resulted in decreased inflammation. • Mechanistic differences in regulating Cr(VI)-induced inflammation.

Delay and probability discounting among payday and title loan recipients.

Science.gov (United States)

Mahoney, Colin T; Lawyer, Steven R

2016-04-01

Payday and title loans are short-term loans associated with significant economic impact. Behavioral theories of impulsive choice may provide insight into behavioral processes that underlie the propensity to take out payday and title loans. Adults between the ages of 18 and 30 recruited from the community completed delay and probability discounting tasks for hypothetical money as well as measures of substance use. Patterns of discounting were characterized using a hyperbolic decay model and area under the curve. Participants who took out a payday and/or title loan in the past (n=41) exhibited more impulsive choice patterns on the delay discounting task than did those who did not (n=255). Substance use mediated this relationship between payday and title loan retention and delay discounting. These findings suggest potentially important relationships between payday/title loan borrowing, substance use, and delay discounting. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of genotype, Cr(III and Cr(VI on plant growth and micronutrient status in Silene vulgaris (Moench

Directory of Open Access Journals (Sweden)

A. E. Pradas-del-Real

2013-06-01

Full Text Available Chromium released into the environment from industrial activities has become an important environmental concern. Silene vulgaris has been proven to be tolerant to many heavy metals, so it is considered an interesting species in the revegetation and restoration of polluted soils, but no information is available about its response to Cr. The objective of this work was to study uptake and influence on plant growth of Cr(III and Cr(VI in six genotypes (four hermaphrodites and two females of S. vulgaris from different sites of Madrid (Spain. Plants were treated for 12 days with 60 µM of Cr(III or Cr(VI in semihydroponics. Dry weights, soil-plant analysis development values (SPAD reading with chlorophylls and micronutrient and total Cr concentrations were determined. Metal uptake was higher in presence of Cr(VI than of Cr(III and poorly translocated to the shoots. In both cases S. vulgaris did not show visual toxicity symptoms, biomass reduction, or differences among SPAD values as consequence of Cr additions. However genotypes SV36 and SV38 showed Fe and Mn imbalance. This is the first report on the relatively good performance of hermaphrodite and female S. vulgaris genotypes in Cr uptake and physiological traits, but further studies will be necessary to elucidate the mechanisms by which the gender may influence these variables. S. vulgaris presented high diversity at genotypic level; the treatment with hexavalent Cr increased the differences among genotypes so the use of cuttings from an homogeneous genotype seems to be an adequate method for the study of this species.

Commercial off-the-shelf software dedication process based on the commercial grade survey of supplier

International Nuclear Information System (INIS)

Kim, J. Y.; Lee, J. S.; Chon, S. W.; Lee, G. Y.; Park, J. K.

2000-01-01

Commercial Off-The-Shelf(COTS) software dedication process can apply to a combination of methods like the hardware commercial grade item dedication process. In general, these methods are : methods 1(special test and inspection), method 2(commercial grade survey of supplier), method 3(source verification), and method 4(acceptance supplier/item performance record). In this paper, the suggested procedure-oriented dedication process on the basis of method 2 for COTS software is consistent with EPRI/TR-106439 and NUREG/CR-6421 requirements. Additional tailoring policy based on code and standards related to COTS software may be also founded in the suggested commercial software dedication process. Suggested commercial software dedication process has been developed for a commercial I and C software dedication who performs COTS qualification according to the dedication procedure

Variation in job titles within the nursing workforce.

Science.gov (United States)

Leary, Alison; Maclaine, Katrina; Trevatt, Paul; Radford, Mark; Punshon, Geoffrey

2017-12-01

The work of specialist nursing has been under scrutiny for many years in the UK due to a perception that it is not cost-effective. A common issue is the lack of consistency of job titles, which causes confusion to the public, employing organisations, colleagues and commissioners of services. Lack of consistency has implications for the wider perception of advanced specialist practice in the worldwide community and the workforce more generally. This study aims to understand the variation in job titles in the UK population. A pre-existing data set of accrued studies into the work of nurses working in specialisms was mined for insight (N = 17,960). This study used knowledge discovery through data and descriptive statistics to perform secondary analysis. Mining these data revealed 595 job titles in use in 17,960 specialist posts once the specialism had been removed. The most commonly used titles were Clinical Nurse Specialist, Nurse Specialist/Specialist Nurse, Advanced Nurse Practitioner and Nurse Practitioner. There were three other primary groupings. These were variants with a specialist or technical prefix of suffix, for example Nurse Endoscopist, variants of seniority such as trainee, senior nurse for [specialism] or variants of function such as Nurse Prescriber. The clustering was driven primarily by pay band. A total of 323 posts were recorded as holding titles such as Advanced Nurse Practitioner or Specialist Nurse who were not registered with the Nursing & Midwifery Council. In this data set, there is a large array of titles, which appear to have little relationship with other factors like education. This is confusing to the public, employers and those commissioning services. It also demonstrates that the previous assumptions by Council for Healthcare Regulatory Excellence that advanced practice labels are associated with career progression are unsound and should be addressed by the regulator. © 2017 John Wiley & Sons Ltd.

Microstructure, Wear Behavior and Corrosion Resistance of WC-FeCrAl and WC-WB-Co Coatings

Directory of Open Access Journals (Sweden)

Janette Brezinová

2018-05-01

Full Text Available The paper is focused on investigating the quality of two grades of thermally sprayed coatings deposited by high-velocity oxygen fuel (HVOF technology. One grade contains WC hard particles in an environmentally progressive Ni- and Co-free FeCrAl matrix, while the second coating contains WC and WB hard particles in a cobalt matrix. The aim of the experimental work was to determine the effect of thermal cyclic loading on the coatings’ resistance to adhesive, abrasive and erosive wear. Abrasive wear was evaluated using abrasive cloth of two grit sizes, and erosive wear was evaluated by a dry-pot wear test in a pin mill at two sample angles. Adhesion wear resistance of the coatings was determined by a sliding wear test under dry friction conditions and in a 1 mol water solution of NaCl. Corrosion resistance of the coatings was evaluated using potentiodynamic polarization tests. Metallographic cross-sections were used for measurement of the microhardness and thickness and for line energy-dispersive X-ray (EDX analysis. The tests proved the excellent resistance of both coatings against adhesive, abrasive, and erosive wear, as well as the ability of the WC-WB-Co coating to withstand alternating temperatures of up to 600 °C. The “green carbide” coating (WC-FeCrAl can be recommended as an environmentally friendly replacement for Ni- and Co-containing coatings, but its operating temperature is strictly limited to 500 °C in air.

Aboriginal Determination: Native Title Claims and Barriers to Recognition

Directory of Open Access Journals (Sweden)

Zia Akhtar

2011-09-01

Full Text Available The Australian government has proposed a referendum in 2012 to decide the constitutional status of its indigenous people. There is at present no mechanism to define the indigenous people as a domestic or foreign entity of the Commonwealth. This is an important issue because other settler governments have developed a framework to implement their relationship with the native people. As a result, it is difficult prove title to land that has been abrogated by the deeds of the settlers. In Mabo v Queensland (2,the Commonwealth government was found to have breached its fiduciary duty to the Aboriginal peoples. The judgment led to the Native Title Act 1993 that established the process of asserting native rights that were held to coexist with pastoral ownership. The promulgation of the Native Title Amendment Act 1998 reversed this process and augmented the powers of non-native landlords by providing the device to extinguish native rights. In Western Australia v Ward, a mining lease was held to have precedence over native title that was adjudged to be part of a bundle of rights. In implementing the Native Title Act the issue turns on the determination of the ties to land/ sea that the government allows to the Aboriginal peoples. The judgment in Harrington-Smith on behalf of the Wongatha People v Western Australia indicates that title can be excluded on procedural grounds and that there was an incompatibility between the claims of the Aboriginal peoples and the settlers’ claims. The road map towards a more effective regime of proving title can be achieved if the Aboriginal peoples are granted recognition as a nation in the Constitution and a treaty is signed with them.

Observations of a Cast Cu-Cr-Zr Alloy

Science.gov (United States)

Ellis, David L.

2006-01-01

Prior work has demonstrated that Cu-Cr-Nb alloys have considerable advantages over the copper alloys currently used in regeneratively cooled rocket engine liners. Observations indicated that Zr and Nb have similar chemical properties and form very similar compounds. Glazov and Zakharov et al. reported the presence of Cr2Zr in Cu-Cr-Zr alloys with up to 3.5 wt% Cr and Zr though Zeng et al. calculated that Cr2Zr could not exist in a ternary Cu-Cr-Zr alloy. A cast Cu-6.15 wt% Cr-5.25 wt% Zr alloy was examined to determine if the microstructure developed would be similar to GRCop-84 (Cu-6.65 wt% Cr-5.85 wt% Nb). It was observed that the Cu-Cr-Zr system did not form any Cr2Zr even after a thermal exposure at 875 C for 176.5 h. Instead the alloy consisted of three phases: Cu, Cu5Zr, and Cr.

Er,Cr:YSGG Laser as a Novel Method for Rebonding Failed Ceramic Brackets.

Science.gov (United States)

Sohrabi, Aydin; Jafari, Sanaz; Kimyai, Soodabeh; Rikhtehgaran, Sahand

2016-10-01

Since there is no standard method for rebonding loose ceramic brackets, the aim of this study was to evaluate the possibility of using Er,Cr:YSGG laser to eliminate the remaining composite materials from the base of ceramic brackets and to compare the bond strength of rebonded brackets with the new ones. Sixty-two extracted human premolars were mounted in acrylic cylinders. Thirty-one ceramic brackets were bonded, and shear bond strength was tested using Hounsfield testing machine. The remnants of the bonding material were removed from the bases of brackets using Er,Cr:YSGG laser. These brackets were rebonded to 31 fresh teeth and again shear bond strength was measured. Pattern of debonding was assessed in both cases under a stereomicroscope and graded according to ARI index. Data were analyzed with independent t-test and Fisher's exact test. Mean shear bond strength of the bond and rebond groups was 12.29 ± 5.46 and 10.58 ± 5.16 MPa, respectively. There were no significant differences between the two groups (p = 0.21). Pattern of bond failure was not statistically different between the two groups. Er,Cr:YSGG laser was effective in removing the remnants of bonding material from the base of ceramic brackets without any interference with the ceramic base itself, demonstrating that it might be a suitable method for rebonding ceramic brackets.

Millimeter-wave spectroscopy of CrC (X(3)Σ(-)) and CrCCH (X̃ (6)Σ(+)): Examining the chromium-carbon bond.

Science.gov (United States)

Min, J; Ziurys, L M

2016-05-14

Pure rotational spectroscopy of the CrC (X(3)Σ(-)) and CrCCH (X̃ (6)Σ(+)) radicals has been conducted using millimeter/sub-millimeter direct absorption methods in the frequency range 225-585 GHz. These species were created in an AC discharge of Cr(CO)6 and either methane or acetylene, diluted in argon. Spectra of the CrCCD were also recorded for the first time using deuterated acetylene as the carbon precursor. Seven rotational transitions of CrC were measured, each consisting of three widely spaced, fine structure components, arising from spin-spin and spin-rotation interactions. Eleven rotational transitions were recorded for CrCCH and five for CrCCD; each transition in these cases was composed of a distinct fine structure sextet. These measurements confirm the respective (3)Σ(-) and (6)Σ(+) ground electronic states of these radicals, as indicated from optical studies. The data were analyzed using a Hund's case (b) Hamiltonian, and rotational, spin-spin, and spin-rotation constants have been accurately determined for all three species. The spectroscopic parameters for CrC were significantly revised from previous optical work, while those for CrCCH are in excellent agreement; completely new constants were established for CrCCD. The chromium-carbon bond length for CrC was calculated to be 1.631 Å, while that in CrCCH was found to be rCr-C = 1.993 Å - significantly longer. This result suggests that a single Cr-C bond is present in CrCCH, preserving the acetylenic structure of the ligand, while a triple bond exists in CrC. Analysis of the spin constants suggests that CrC has a nearby excited (1)Σ(+) state lying ∼16 900 cm(-1) higher in energy, and CrCCH has a (6)Π excited state with E ∼ 4800 cm(-1).

Tribological properties and surface structures of ion implanted 9Cr18Mo stainless steels

International Nuclear Information System (INIS)

Fengbin, Liu; Guohao, Fu; Yan, Cui; Qiguo, Sun; Min, Qu; Yi, Sun

2013-01-01

The polished quenched-and-tempered 9Cr18Mo steels were implanted with N ions and Ti ions respectively at a fluence of 2 × 10 17 ions/cm 2 . The mechanical properties of the samples were investigated by using nanoindenter and tribometer. The results showed that the ion implantations would improve the nanohardness and tribological property, especially N ion implantation. The surface analysis of the implanted samples was carried out by using XRD, XPS and AES. It indicated that the surface exhibits graded layers after ion implantation. For N ion implantation, the surface about 20 nm thickness is mainly composed of supersaturated interstitial N solid solution, oxynitrides, Cr x C y phase and metal nitrides. In the subsurface region, the metal nitrides dominate and the other phases disappear. For Ti ion implantation, the surface of about 20 nm thickness is mainly composed of titanium oxides and carbon amorphous phase, the interstitial solid solution of Ti in Fe is abundant in the subsurface region. The surface components and structures have significant contributions to the improved mechanical properties

Morphology, deformation, and defect structures of TiCr2 in Ti-Cr alloys

International Nuclear Information System (INIS)

Chen, K.C.; Allen, S.M.; Livingston, J.D.

1992-01-01

The morphologies and defect structures of TiCr 2 in several Ti-Cr alloys have been examined by optical metallography, x-ray diffraction, and transmission electron microscopy (TEM), in order to explore the room-temperature deformability of the Laves phase TiCr 2 . The morphology of the Laves phase was found to be dependent upon alloy composition and annealing temperature. Samples deformed by compression have also been studied using TEM. Comparisons of microstructures before and after deformation suggest an increase in twin, stacking fault, and dislocation density within the Laves phase, indicating some but not extensive room-temperature deformability

24 CFR 1710.209 - Title and land use.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Title and land use. 1710.209... § 1710.209 Title and land use. (a) General information. (1) State whether the developer has reserved the... recording, submit a map which has been prepared to scale and which shows the proposed division of the land...

Development of improved HP/IP rotor material 2% CrMoNiWV (23 CrMoNiWV 88)

International Nuclear Information System (INIS)

Wiemann, W.

1989-01-01

The new 2% CrMoNiWV steel has a sufficient strength level, a very good creep (rupture) behaviour and an excellent toughness behaviour for a creep resistant steel. Even after long time high temperature exposure the toughness degradation is so small that it is still better than this of best 1% CrMo(Ni)V steels. The fatigue behaviour is well comparable to this of 1% CrMo(Ni)V. The 2% CrMoNiWV steel has the capability to substitute the traditional 1% CrMo(Ni)V. (orig.) With 26 annexes

[Association between occupational stress and presenteeism among medical staff at grade A tertiary hospitals in Shanghai, China].

Science.gov (United States)

Dai, Junming; Hua, Yujie; Zhang, Hao; Huang, Li; Fu, Hua

2015-10-01

To investigate the current status of occupational stress and presenteeism among medical staff at grade A tertiary hospitals in Shanghai, China, and to analyze the association between occupational stress and presenteeism. A total of 2356 healthcare workers from eight grade A tertiary hospitals in Shanghai were investigated by stratified random sampling. All the subjects were asked to complete self-administered questionnaires with informed consent. The occupational stress was assessed by the occupational stress core questionnaire. The presenteeism was evaluated by the Stanford Presenteeism Scale. In all subjects, the average score of presenteeism was 15.23 ± 3.89, and 72.5% felt occupational stress in self-evaluation. There were significant differences in the score of presenteeism between subjects with different ages, education levels, occupations, lengths of service, job titles, and shifts (all Poccupational stress, including job demand, control, social support, and demand-control ratio (Poccupational stress in medical staff from grade A tertiary hospitals is positively correlated with the level of presenteeism. It is important to promote social support to reduce the loss of work efficiency due to presenteeism.

Evaluation on the Effect of Composition on Radiation Hardening and Embrittlement in Model FeCrAl Alloys

Energy Technology Data Exchange (ETDEWEB)

Field, Kevin G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Briggs, Samuel A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Edmondson, Philip [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hu, Xunxiang [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Littrell, Kenneth C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Howard, Richard [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Parish, Chad M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yamamoto, Yukinori [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-09-18

networks acting as defect sinks, resulting in variations in the observed microstructures after irradiation. Dose trends were also observed, with increasing radiation dose promoting changes in the size and number density of the Cr-rich α' precipitates. Based on the microstructural analysis, performed tensile testing, and prior knowledge from FeCr literature it was hypothesized that the formation of the Cr-rich α' precipitates could lead to significant radiation-induced embrittlement in the alloys, and this could be composition dependent, a result which would mirror the trends observed for radiation-induced hardening. Due to the limited database on embrittlement in the FeCrAl alloy class after irradiation, a series of radiation experiments have been implemented. The overarching point of view within this report is the radiation tolerance of FeCrAl is complex, with many mechanisms and factors to be considered at once. Further development of the FeCrAl alloy class for enhanced accident tolerant applications requires detailed, single (or at least limited) variable experiments to fully comprehend and predict the performance of this alloy in LWRs. This report has been submitted as fulfillment of milestone M2FT-15OR0202321 titled, Summary report on the effect of composition on the irradiation embrittlement of Gen 1 ATF FeCrAl for the Department of Energy Office of Nuclear Energy, Advanced Fuel Campaign of the Fuel Cycle R&D program.

Corrosion resistance of amorphous NiCrZr and NiCrMoZr alloys

International Nuclear Information System (INIS)

Naka, M.; Miyake, M.; Okamoto, I.

1987-01-01

One of the authors has reported that the corrosion resistance of chromium containing amorphous alloys is extremely improved by alloying phosphorus among metalloids. Two factors operate for the improvement of corrosion resistance of the amorphous alloys. First, phosphorus serves for the rapid formation of protective passive film. Second, the compositional and structural homogeneity in amorphous state also account for the formation of protective film. The latter factor has been clearly seen in the high corrosion resistance of CoCrMoZr and CoCrWZr alloys without metalloids. In order to clarify the separately two factors in the corrosion resistance of amorphous alloys, the corrosion resistance of amorphous alloys without metalloids has to be further investigated. This paper also deals with the corrosion resistance and electrochemical behavior of NiCrZr and NiCrMoZr alloys in 1N HCl, and compare them with the corrosion behavior of the crystalline alloys containing the same composition as that of the amorphous alloys

The irradiation hardening of Ni-Mo-Cr and Ni-W-Cr alloy under Xe26+ ion irradiation

Science.gov (United States)

Chen, Huaican; Hai, Yang; Liu, Renduo; Jiang, Li; Ye, Xiang-xi; Li, Jianjian; Xue, Wandong; Wang, Wanxia; Tang, Ming; Yan, Long; Yin, Wen; Zhou, Xingtai

2018-04-01

The irradiation hardening of Ni-Mo-Cr and Ni-W-Cr alloy was investigated. 7 MeV Xe26+ ion irradiation was performed at room temperature and 650 °C with peak damage dose from 0.05 to 10 dpa. With the increase of damage dose, the hardness of Ni-Mo-Cr and Ni-W-Cr alloy increases, and reaches saturation at damage dose ≥1 dpa. Moreover, the damage dose dependence of hardness in both alloys can be described by the Makin and Minter's equation, where the effective critical volume of obstacles can be used to represent irradiation hardening resistance of the alloys. Our results also show that Ni-W-Cr alloy has better irradiation hardening resistance than Ni-Mo-Cr alloy. This is ascribed to the fact that the W, instead of Mo in the alloy, can suppress the formation of defects under ion irradiation.

Oxidation-resistant Ge-doped silicide coating on Cr-Cr2Nb alloys by pack cementation

International Nuclear Information System (INIS)

He Yirong

1997-01-01

The halide-activated pack cementation process was modified to produce a Ge-doped silicide diffusion coating on Cr-Cr 2 Nb alloys in a single processing step. The morphology and composition of the coating depended both on the pack composition and processing schedule and also on the composition and microstructure of the substrate. Higher Ge content in the pack suppressed the formation of CrSi 2 and reduced the growth kinetics of the coating. Ge was not homogeneously distributed in the coatings. Under cyclic and isothermal oxidation conditions, the Ge-doped silicide coating protected the Cr-Nb alloys from significant oxidation and from pesting by the formation of a Ge-doped silica film. (orig.)

Substrate bias effects on composition and coercivity of CoCrTa/Cr thin films on canasite and glass

Science.gov (United States)

Deng, Y.; Lambeth, D. N.; Sui, X.; Lee, L.-L.; Laughlin, D. E.

1993-05-01

CoCrTa/Cr thin films were prepared by rf diode sputtering onto canasite and glass substrates at various bias voltages from two targets of different compositions (Co82.8Cr14.6Ta2.6 and Co86Cr12Ta2). While Auger depth profile analysis indicates that there is some broadening at the CoCrTa-Cr interface, x-ray fluorescence spectroscopy reveals that changes in alloy composition due to the resputtering processes are even more prominent. For both targets, as the substrate bias increases the Co content in the films declines, and the magnetization decreases. The maximum film coercivity appears to correlate to the final film composition. By investigating the results from both targets, it is concluded that the coercivity reaches a maximum when the film composition is in the neighborhood of Co84Cr13Ta3. Thus, to optimize the coercivity different bias voltages are required for each target. Excessive substrate bias, however, leads to films with low magnetization and coercivity.

7 CFR 810.2204 - Grades and grade requirements for wheat.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Grades and grade requirements for wheat. 810.2204... OFFICIAL UNITED STATES STANDARDS FOR GRAIN United States Standards for Wheat Principles Governing the Application of Standards § 810.2204 Grades and grade requirements for wheat. (a) Grades and grade requirements...

Ductilization of Cr via oxide dispersions

International Nuclear Information System (INIS)

Brady, M.P.; Wright, I.G.; Anderson, I.M.; Sikka, V.K.; Ohriner, E.K.; Walls, C.; Westmoreland, G.; Weaver, M.L.

2001-01-01

Work by Scruggs et al. in the 1960's demonstrated that up to 20 % tensile ductility could be achieved at room-temperature in sintered and extruded powder metallurgical Cr alloyed with MgO. During sintering, much of the MgO converts to a MgCr 2 O 4 spinel, which was hypothesized to getter nitrogen from the Cr, rendering it ductile. Recent efforts at Oak Ridge National Laboratory (ORNL) have succeeded in duplicating this original effect. Preliminary results suggest that the ductilization mechanism may be more complicated than the simple nitrogen gettering mechanism proposed by Scruggs, as some ductility was observed at room-temperature in Cr-MgO alloys containing nitride precipitates. Results of microstructural characterization and room-temperature mechanical property studies are presented for Cr-6MgO-(0-2.2) Ti wt.% as a function of hot-pressing and extrusion. Possible mechanisms by which the MgO additions may improve the room-temperature ductility of Cr are discussed. (author)

Tantalum-containing Z-phase in 12%Cr martensitic steels

DEFF Research Database (Denmark)

Danielsen, Hilmar Kjartansson; Hald, John

2009-01-01

Z-phases in tantalum-containing 12%Cr steels have been investigated. In 12%Cr steel without any Nb or V, the formation of CrTaN Z-phases was observed. In 12%Cr steel which also contained V, the Ta entered Z-phase as a minor element, Cr(V,Ta)N. The crystal structure of Cr(V,Ta)N seems to be identi......Z-phases in tantalum-containing 12%Cr steels have been investigated. In 12%Cr steel without any Nb or V, the formation of CrTaN Z-phases was observed. In 12%Cr steel which also contained V, the Ta entered Z-phase as a minor element, Cr(V,Ta)N. The crystal structure of Cr(V,Ta)N seems...

Pacific Custom Materials, Petition to Object to Title V Operating Permit

Science.gov (United States)

This document may be of assistance in applying the Title V air operating permit regulations. This document is part of the Title V Petition Database available at www2.epa.gov/title-v-operating-permits/title-v-petition-database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Characterization of Cr-rich Cr-Sb multilayer films: Syntheses of a new metastable phase using modulated elemental reactants

International Nuclear Information System (INIS)

Regus, Matthias; Mankovsky, Sergiy; Polesya, Svitlana; Kuhn, Gerhard; Ditto, Jeffrey; Schürmann, Ulrich; Jacquot, Alexandre; Bartholomé, Kilian; Näther, Christian; Winkler, Markus; König, Jan D.; Böttner, Harald; Kienle, Lorenz; Johnson, David C.; Ebert, Hubert; Bensch, Wolfgang

2015-01-01

The new metastable compound Cr 1+x Sb with x up to 0.6 has been prepared via a thin film approach using modulated elemental reactants and investigated by in-situ X-ray reflectivity, X-ray diffraction, differential scanning calorimetry, energy dispersive X-ray analysis as well as transmission electron microscopy and atomic force microscopy. The new Cr-rich antimonide crystallizes in a structure related to the Ni 2 In-type structure, where the crystallographic position (1/3, 2/3, 3/4) is partially occupied by excess Cr. The elemental layers of the pristine material interdiffused significantly before Cr 1+x Sb crystallized. A change in the activation energy was observed for the diffusion process when crystal growth starts. First-principles electronic structure calculations provide insight into the structural stability, magnetic properties and resistivity of Cr 1+x Sb. - Graphical abstract: 1 amorphous multilayered film 2 interdiffused amorphous film 3 metastable crystalline phase 4 thermodynamic stable phase (and by-product). - Highlights: • Interdiffusion of amorphous Cr and Sb occurs before crystallization. • Crystallization of a new metastable phase Cr 1.6 Sb in Ni 2 In-type structure. • The new Cr-rich phase shows half-metallic behavior

Cu-Cr Literature Review

Energy Technology Data Exchange (ETDEWEB)

Need, Ryan F. [Los Alamos National Laboratory

2012-08-09

Cu-Cr alloys are part of a class of face-centered cubic (FCC)-body-centered cubic (BCC) composites that includes similar alloys, such as Cu-Nb and Cu-Ta. When heavily deformed, these FCC-BCC materials create 'in situ' composites with a characteristic structure-nanoscale BCC filaments in a ductile FCC matrix. The strength of these composites is vastly greater than predicted by the rule of mixtures, and has been shown to be inversely proportional to the filament spacing. Lower raw materials costs suggest that Cu-Cr alloys may offer more economical solution to high-strength, high-conductivity wire than either their Nb or Ta counterparts. However, Cr is also more brittle and soluble in Cu than Nb or Ta. These qualities necessitate thermal treatments to remove solute atoms from the Cu matrix, improve conductivity, and maintain the ductility of the Cr filaments. Through the use of different thermomechanical processing routes or the addition of select dopants, alloys with strength in excess of 1 GPa at 70% IACS have been achieved. To date, previous research on Cu-Cr alloys has focused on a relatively small number of alloy compositions and processing methods while the effects of dopants and ageing treatments have only been studied independently. Consequently, there remains considerable opportunity for the development and optimization of these alloys as a leading high-strength, high-conductivity material.

Thermodynamic Assessment of the La-Cr-O System

DEFF Research Database (Denmark)

Povoden, E.; Chen, Ming; Grundy, A.N.

2009-01-01

of oxygen partial pressure. In the La-Cr system reported solubility of lanthanum in bcc chromium is considered in the modeling. In the La-Cr-O system the Gibbs energy functions of La2CrO6, La-2(CrO4)(3), and perovskite-structured LaCrO3 are presented, and oxygen solubilities in bcc and fcc metals......The La-Cr and the La-Cr-O systems are assessed using the Calphad approach. The calculated La-Cr phase diagram as well as LaO1.5-CrO1.5 phase diagrams in pure oxygen, air, and under reducing conditions are presented. Phase equilibria of the La-Cr-O system are calculated at 1273 K as a function...... are modeled. Emphasis is placed on a detailed description of the perovskite phase: the orthorhombic to rhombohedral transformation and the contribution to the Gibbs energy due to a magnetic order-disorder transition are considered in the model. The following standard data of stoichiometric perovskite...

Effects of lipopolysaccharides on the corrosion behavior of Ni-Cr and Co-Cr alloys.

Science.gov (United States)

Yu, Weiqiang; Qian, Chao; Weng, Weimin; Zhang, Songmei

2016-08-01

Lipopolysaccharides (LPS) are constituents of gingival crevicular fluid and may affect the base metal alloys used in metal ceramic crowns. The role of LPS in base metal alloys is currently unknown. The purpose of this in vitro study was to evaluate the effects of gram-negative bacterial LPS on the electrochemical behavior of Ni-Cr and Co-Cr alloys. Alloy specimens were divided into 4 groups according to Escherichia coli LPS concentration (0, 0.15, 15, and 150 μg/mL) in acidic saliva (pH 5). Open circuit potential (OCP) and potentiodynamic polarization behavior were examined using a computer-controlled potentiostat. Metal ions released from the 2 alloys were measured by immersion in LPS-free solution and 150 μg/mL LPS solution and analyzed by inductively coupled plasma atomic emission spectrometry (ICP-AES). Data were evaluated using 1-way ANOVA (α=.05). Compared with control groups, medium LPS concentration (15 μg/mL) accelerated Ni-Cr alloy corrosion (Palloy corrosion (Pcorrosion current density, and polarization resistance parameters. After immersion in high LPS concentrations (150 μg/mL), a slight increase in Ni ion release (P >.05) was observed for the Ni-Cr alloy, while a more significant Co ion release (Palloy. LPS negatively affected the electrochemical behavior of both the Ni-Cr and Co-Cr alloys. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Determination of Cr(VI) and Cr(III) in urine and dextrose by inductively coupled plasma emission spectroscopy

Science.gov (United States)

Mianzhi, Zhuang; Barnes, Ramon M.

The determination of Cr(VI) and Cr(III) in human urine and in commercial dextrose solution is performed by induclively coupled plasma-atomic emission spectroscopy after selective preconcentration of the chromium species at different pH values by poly(dithiocarbamate) and poly(acrylamidoxime) chelating resins. The chelating properties of these resins with chromium, including the kinetics of uptake and removal of Cr(III), and the influence of matrix concentrations were evaluated. Chromium in human urine was found to exist exclusively as Cr(III).

When astrophysics meets lay and specialized audiences: titles in popular and scientific papers

OpenAIRE

Alcaraz Ariza, María Ángeles; Méndez Alcaraz, David Israel

2016-01-01

In this study we carry out a comparative analysis between titles of research papers published in the most authoritative specialized European and US-based astrophysics journals written in English and titles of articles on astrophysics published in Scientific American Magazine, the most prestigious English-written journal in the divulgation of science. We specifically address issues related to three linguistic variables: title length, title lexical density and title type. Our main results show ...

Development of low-Cr ODS FeCrAl alloys for accident-tolerant fuel cladding

Science.gov (United States)

Dryepondt, Sebastien; Unocic, Kinga A.; Hoelzer, David T.; Massey, Caleb P.; Pint, Bruce A.

2018-04-01

Low-Cr oxide dispersion strengthened (ODS) FeCrAl alloys were developed as accident tolerant fuel cladding because of their excellent oxidation resistance at very high temperature, high strength and improved radiation tolerance. Fe-12Cr-5Al wt.% gas atomized powder was ball milled with Y2O3+FeO, Y2O3+ZrO2 or Y2O3+TiO2, and the resulting powders were extruded at 950 °C. The resulting fine grain structure, particularly for the Ti and Zr containing alloys, led to very high strength but limited ductility. Comparison with variants of commercial PM2000 (Fe-20Cr-5Al) highlighted the significant impact of the powder consolidation step on the alloy grain size and, therefore, on the alloy mechanical properties at T < 500 °C. These low-Cr compositions exhibited good oxidation resistance at 1400 °C in air and steam for 4 h but could not form a protective alumina scale at 1450 °C, similar to observations for fine grained PM2000 alloys. The effect of alloy grain size, Zr and Ti additions, and impurities on the alloy mechanical and oxidation behaviors are discussed.

24 CFR 1710.109 - Title to the property and land use.

Science.gov (United States)

2010-04-01

... under the authority of title IV of the Intergovernmental Cooperation Act of 1968.) ... title to property generally has the right to own, use and enjoy the property. A contract to buy a lot... affect your title.” “Here we will discuss the sales contract you will sign and the deed you will receive...

Parents Ask about Title I = Los padres preguntan del Titulo I.

Science.gov (United States)

RMC Research Corp., Portsmouth, NH.

Title I, the largest federal aid program for elementary, middle, and high schools, is introduced in this publication, which includes both English and Spanish versions. Through Title I, the Federal government gives money to school districts around the country based on the number of low-income families in each district. Each district uses Title I…

THE SYNTHESIS OF Cr2O3-PILLARED MONTMORILLONITE (CrPM AND ITS USAGE FOR HOST MATERIAL OF p-NITROANILINE

Directory of Open Access Journals (Sweden)

Karna Wijaya

2010-06-01

Full Text Available The synthesis of Cr2O3-pillared montmorillonite (CrPM and its usage for host material of p-nitroaniline have been conducted. The Cr2O3-pillared montmorillonite clays was prepared by a direct ion exchange method. First, the polyhydroxychromium as a pillaring spesies was intercalated into the interlayer region of the montmorillonite clays (purified clay in the monocation form, result in a montmorillonite-polyoxychromium intercalation compound. The precursors/pillaring spesies was not stable, hence it must be stabilized by calcination in order to transform the polyoxychromium via dehydration and dehydroxylation processes into Cr2O3. This oxide constituts the so-called pillar that prop the clay layers apart to a relatively large distance. The Cr2O3-pillared clays as a host material was added into ethanol solution saturated with p-nitroaniline, and mixture was stirred for 24 h at room temperature. The Na-montmorillonite, Cr2O3-pillared clay and p-nitroaniline-Cr2O3-pillared clay (pNA-CrPM were characterized by X-Ray Diffraction (XRD, Gas Sorption Analysis, Infrared Spectroscopy (FTIR and Activated Neutron Analysis (ANA methods. The result of research showed that basal spacing (d001 of Cr2O3-pillared montmorillonite (CrPM was 18,55 Å, meanwhile the basal spacing of the hydrated Na-montmorillonite was 14,43 Å. The specific surface area of the Cr2O3-pillared montmorillonite was 174,308 m2/g, whereas p-nitroaniline-Cr2O3-pillared clay (pNA-CrPM was 133,331641 m2/g. This fact indicated that p-nitroaniline has been included into the pore of the Cr2O3-pillared clay.   Keyword: montmorillonite, pillared-clay, ion exchange, intercalate.

Hot Corrosion Behavior of Bare, Cr3C2-(NiCr) and Cr3C2-(NiCr) + 0.2wt.%Zr Coated SuperNi 718 at 900 °C

Science.gov (United States)

Mudgal, Deepa; Singh, Surendra; Prakash, Satya

2015-01-01

Corrosion in incinerators, power plants, and chemical industries are frequently encountered due to the presence of salts containing sodium, sulphur, and chlorine. To obviate this problem, bare and coated alloys were tested under environments simulating the conditions present inside incinerators and power plants. 0.2 wt.% zirconium powder was incorporated in the Cr3C2-(NiCr) coating powder. The original powder and Zr containing powder was sprayed on Superni 718 alloy by D-gun technique. The bare and coated alloys were tested under Na2SO4 + K2SO4 + NaCl + KCl and Na2SO4 + NaCl environment. The corrosion rate of specimens was monitored using weight change measurements. Characterization of the corrosion products has been done using FE-SEM/EDS and XRD techniques. Bare and coated alloys showed very good corrosion resistance under given molten salt environments. Addition of 0.2wt.%Zr in Cr3C2-25%(NiCr) coating further greatly reduced the oxidation rate as well as improved the adherence of oxide scale to the coating surface during the time of corrosion.

Interdiffusion processes at irradiated Cr/Si interfaces

Energy Technology Data Exchange (ETDEWEB)

Luneville, L., E-mail: laurence.luneville@cea.fr [DEN/DANS/DM2S/SERMA/LLPR/LRC-CARMEN, CEA Saclay, 91191 Gif-sur-Yvette (France); Largeau, L. [LPN-UPR20/CNRS, Route de Nozay, 91460 Marcoussis (France); Deranlot, C. [Unite Mixte de Physique CNRS/Thales, 1 Avenue Augustin Fresnel, 91767 Palaiseau (France); Ribis, J. [DEN/DANS/DMN/SRMA/LA2M/LRC-CARMEN, CEA Saclay, 91191 Gif-sur-Yvette (France); Ott, F. [DSM/IRAMIS/LLB/CEA/CNRS, CEA Saclay, 91191 Gif-sur-Yvette (France); Moncoffre, N. [IPNL/CNRS, Domaine scientifique de la Doua, 69622 Villeurbanne (France); Baldinozzi, G. [CNRS-SPMS/UMR 8580/LRC CARMEN Ecole Centrale Paris, 92295 Chatenay-Malabry (France); Simeone, D. [DEN/DANS/DMN/SRMA/LA2M/LRC-CARMEN, CEA Saclay, 91191 Gif-sur-Yvette (France)

2015-03-25

Highlights: • Interdiffusion at Cr/Si interfaces induced by ion beam mixing at room temperature. • Creation of Cr/Si alloy metastable phases. • Reconstruction of Cr/Si interdiffusion profile by X-ray reflectometry. • Quantitative correlation between Cr and Si profiles extracted from XRR and measured by EDX–TEM. - Abstract: Chromium silicon CrSi alloys are foreseen as possible materials for spintronic devices. Ion beam mixing could be an efficient technique to produce thin films of such alloys at room temperature while avoiding thermal diffusion. In order to assess this point, we have irradiated 20 nm Cr layer on a (1 0 0) Si wafer with 70 keV Kr ions. The X-ray reflectometry technique combined with Transmission Electron Microscopy and Energy Dispersive X-ray analysis was applied to analyze, at the nanometric scale, the formation of Cr/Si blurred interfaces induced by ion beam mixing. From the analysis of reflectivity curves, it appears that nanometric Cr{sub 5}Si{sub 3} and CrSi{sub 2} phases are produced at the early stage of the process. The existence of these two paramagnetic phases gives some clues to explain the reason why the experimentally observed ferrimagnetism was weaker than predicted.

Title List of documents made publicly available

International Nuclear Information System (INIS)

1982-07-01

The Title List of Documents Made Publicly Available is a monthly publication. It contains descriptions of the information received and generated by the US Nuclear Regulatory Commission (NRC). This information includes: (1) docketed material associated with civilian nuclear power plants and other uses of radioactive materials and (2) nondocketed material received and generated by NRC pertinent to its role as a regulatory agency. As used here, docketed does not refer to Court dockets; it refers to the system by which NRC maintains its regulatory records. This series of documents is indexed by a Personal Author Index, a Corporate Source Index, and a Report Number Index. The docketed information contained in the Title List includes the information formerly issued through the Department of Energy publication Power Reactor Docket Information, last published in January 1979. Microfiche of the docketed information listed in the Title List is available for sale on a subscription basis from the National Technical Information Service (NTIS)

Title List of documents made publicly available

International Nuclear Information System (INIS)

1982-06-01

The Title List of Documents Made Publicly Available is a monthly publication. It contains descriptions of the information received and generated by the US Nuclear Regulatory Commission (NRC). This information includes: (1) docketed material associated with civilian nuclear power plants and other uses of radioactive materials and (2) nondocketed material received and generated by NRC pertinent to its role as a regulatory agency. As used here, docketed does not refer to Court dockets; it refers to the system by which NRC maintains its regulatory records. This series of documents is indexed by a Personal Author Index, a Corporate Source Index, and a Report Number Index. The docketed information contained in the Title List includes the information formerly issued throught the Department of Energy publication Power Reactor Docket Information, last published in January 1979. Microfiche of the docketed information listed in the Title List is available for sale on a subscription basis from the National Technical Information Service (NTIS)

Cr/alpha-Cr2O3 monodispersed spherical core-shell particles based solar absorbers

CSIR Research Space (South Africa)

Khamlich, S

2011-07-01

Full Text Available as reported. The coated Cr/alpha-Cr2O3 spherical particles on rough copper substrates by a simple self-assembly-like method were characterized by scanning electron microscopy, energy dispersive spectrometry, Raman spectroscopy, and diffuse reflectance UV...

Electron transport in all-Heusler Co2CrSi/Cu2CrAl/Co2CrSi device, based on ab-initio NEGF calculations

Science.gov (United States)

Mikaeilzadeh, L.; Pirgholi, M.; Tavana, A.

2018-05-01

Based on the ab-initio non-equilibrium Green's function (NEGF) formalism based on the density functional theory (DFT), we have studied the electron transport in the all-Heusler device Co2CrSi/Cu2CrAl/Co2CrSi. Results show that the calculated transmission spectra is very sensitive to the structural parameters and the interface. Also, we obtain a range for the thickness of the spacer layer for which the MR effect is optimum. Calculations also show a perfect GMR effect in this device.

Uniform Title in Theory and in Slovenian and Croatian Cataloguing Practice

Directory of Open Access Journals (Sweden)

Marija Petek

2013-09-01

Full Text Available ABSTRACTPurpose:  The paper investigates the importance and development of uniform title that enables collocation in the library catalogue. Research results on use of uniform titles in two union catalogues, the Slovenian COBISS and the Croatian CROLIST are also presented.Methodology/approach:  Theoretical apects of the uniform title are treated: for the first time by Panizzi, then in the Paris Principles being the basis for the Verona's cataloguing code; in the latest International Cataloguing Principles including conceptual models Functional Requirements for Bibliographic Records (FRBR and Functional Requirements for Authority Data (FRAD; and last but not least in the international cataloguing code Resource Description and Access (RDA. To find out whether the uniform titles are used consistently according to the Verona's cataloguing code and to the requirements of the bibliographic formats COMARC and UNIMARC, the frequency of tags 300 and 500 in bibliographic records is explored.Results:  The research results indicate that the use of uniform titles in COBISS and CROLIST is not satisfactory and that the tags 300 and 500 are often missing in bibliographic recods. In online catalogues a special attention should be given to the uniform title as it is considered an efficient linking device in the catalogue and as it enables collocation.Research limitations:  The research is limited to bibliographic records for translations of works of personal authors and of anonymous works; corporate authors are not included.Originality/practical implications:  Presenting development of the uniform title from the very beginning up to now and the first research on the uniform title in COBISS.

Spin flip at unelastic scattering of protons with energy near 6 NeV o 50Cr and 52Cr nuclei

International Nuclear Information System (INIS)

Andronov, Yu.F.; Chubinskij, O.V.; Vinogradov, L.I.; Ehl'-Ashri, F.I.; Gustova, L.V.

1978-01-01

Angular S(Q) and energy S(E) dependences spin flip probability S were studied in inelastic scattering of protons with excitation of the 2 1 + states of 50 Cr (Q=-0.782 MeV) and 52 Cr (Q=-1.434 MeV) energy range from 5.6 to 5.95 MeV. In particular, it is elucidated how strongly the behaviour of the spin flip probability depends upon the energy and angle of scattering at Esub(p) approximately 6 MeV for 50 Cr and 52 Cr. Thereby some additional information on specific features of the mechanism of inelastic sccattering by th nuclei is obtained. Measurements were carried out simultaneously in two proton detection channels at scattering angles differing by 30 deg. For targets use was made of self-sustaining enriched foils (87% 50 Cr and 99% 52 Cr). The angular and energy dependences of the spin flip probabilities for 50 Cr and 52 Cr are shown to be rather different: for 52 Cr has a relatively slight energy dependence in the range of a resonance observed in the excitation function; for 50 Cr the behaviour of S(E) undergoes sharp changes. The experimetnal values of S(Q) for sup(50, 52)Cr differ rather strongly from the calculations made on the statistical model and depend considerably upon the scattering angle

P-type Al-doped Cr-deficient CrN thin films for thermoelectrics

DEFF Research Database (Denmark)

Febvrier, Arnaud le; Van Nong, Ngo; Abadias, Gregory

2018-01-01

Thermoelectric properties of chromium nitride (CrN)-based films grown on c-plane sapphire by dc reactive magnetron sputtering were investigated. In this work, aluminum doping was introduced in CrN (degenerate n-type semiconductor) by co-deposition. Under the present deposition conditions, over......-type/n-type thermoelectric materials based on chromium nitride films, which are cheap and routinely grown on the industrial scale....

Magnetic solid-phase extraction combined with graphite furnace atomic absorption spectrometry for speciation of Cr(III) and Cr(VI) in environmental waters.

Science.gov (United States)

Jiang, Hong-mei; Yang, Ting; Wang, Yan-hong; Lian, Hong-zhen; Hu, Xin

2013-11-15

A new approach of magnetic solid phase extraction (MSPE) coupled with graphite furnace atomic absorption spectrometry (GFAAS) has been developed for the speciation of Cr(III) and Cr(VI) using zincon-immobilized silica-coated magnetic Fe3O4 nanoparticles (Zincon-Si-MNPs) as the MSPE absorbent. Cr(III) was quantitatively reserved on the absorbent at pH 9.1 while total Cr was reserved at pH 6.5. The absorbed Cr species were eluted by using 2 mol/L HCl and detected by GFAAS. The concentration of Cr(VI) could be calculated by subtracting Cr(III) from total Cr. All the parameters affecting the separation and extraction efficiency of Cr species such as pH, extraction time, concentration and volume of eluent, sample volume and influence of co-existing ions were systematically examined and the optimized conditions were established accordingly. The detection limit (LOD) of the method was 0.016 and 0.011 ng mL(-1) for Cr(III) and Cr(VI), respectively, with the enrichment factor of 100 and 150. The precisions of this method (Relative standard deviation, RSD, n=7) for Cr(III) and Cr(VI) at 0.1 ng mL(-1) were 6.0% and 6.2%, respectively. In order to validate the proposed method, a certified reference material of environmental water was analyzed, and the result of Cr speciation was in good agreement with the certified value. This MSPE-GFAAS method has been successfully applied for the speciation of Cr(III) and Cr(VI) in lake and tap waters with the recoveries of 88-109% for the spiked samples. Moreover, the MSPE separation mechanism of Cr(III) and Cr(VI) based on their adsorption-desorption on Zincon-Si-MNPs has been explained through various spectroscopic characterization. © 2013 Elsevier B.V. All rights reserved.

X-ray study of rapidly cooled ribbons of Al-Cr-Zr and Al-Ni-Y-Cr-Zr alloys

International Nuclear Information System (INIS)

Betsofen, S.Ya.; Osintsev, O.E.; Lutsenko, A.N.; Konkevich, V.Yu.

2002-01-01

One investigated into phase composition, lattice spacing and structure of rapidly cooled 25-200 μm gauge strips made of Al-4,1Cr-3,2Zr and Al-1,5Cr-1,5Zr-4Ni-3Y alloys, wt. %, produced by melt spinning to a water-cooled copper disk. In Al-4,1Cr-3,2Zr alloy one detected intermetallic phases: Al 3 Zr and two Al 86 Cr 14 composition icosahedral phases apart from aluminium solid solution with 4.040-4.043 A lattice spacing. In Al-1,5Cr-1,5Zr-4Ni-3Y alloy one identified two Al 86 Cr 14 icosahedral phases and two AlNiY and Al 3 Y yttrium-containing ones, lattice spacing of aluminium solid solution was equal to 4.052-4.053 A [ru

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 1309 ... Li-Long Liu, Kai Xu, Lu-Mei Kang, Shu-Ping Jiang, Qing-Hua Wang, ... CR Sewani-Rusike, JE Iputo, EJ Ndebia, M Gondwe, DR Kamadyaapa ... K-M Man, W-C Chen, H-M Wang, H-Y Chen, J-L Shen, L-D Chen, F-J Tsai, ...

Browse Title Index - AJOL

African Journals Online (AJOL)

Items 501 - 508 of 508 ... Issue, Title. Vol 33, No 2 (2011), Visuele stereotipering van sportvroue in die sportmedia, Abstract. M Brandt, A Carstens. Vol 30, No 1 (2008), Volunteers\\' perceptions of benefits derived from volunteering: an empirical study, Abstract. J Surujlal, M Dhurup. Vol 33, No 1 (2011), Was the Conconi test ...

Fired products of Cr-smectite clays in nitrogen

OpenAIRE

C. Volzone; A. M. Cesio

2004-01-01

The products of Cr-smectite clays heated to 1350 ° C in nitrogen were evaluated by X-ray diffraction and chemical analysis. Cr-smectite clays were prepared at room temperature by contact between smectite clays and Cr species contained in OH-Cr solutions. The Cr species were prepared using chromium nitrate solution by addition of NaOH solution with OH/Cr = 2. Products of firing in nitrogen at the high temperature were different (magnesia chromite, donathite, iron chromium oxide and picrochromi...

Prediction of half-metallic properties in TlCrS{sub 2} and TlCrSe{sub 2} based on density functional theory

Energy Technology Data Exchange (ETDEWEB)

Hashimzade, F.M.; Huseinova, D.A. [Institute of Physics, National Academy of Sciences of Azerbaijan, AZ 1143 Baku (Azerbaijan); Jahangirli, Z.A. [Institute of Physics, National Academy of Sciences of Azerbaijan, AZ 1143 Baku (Azerbaijan); Institute of Radiation Problems, National Academy of Sciences of Azerbaijan, AZ 1143 Baku (Azerbaijan); Mehdiyev, B.H., E-mail: bachschi@yahoo.de [Institute of Physics, National Academy of Sciences of Azerbaijan, AZ 1143 Baku (Azerbaijan)

2017-08-01

Highlights: • Half-metallic properties of TlCrS2, TlCrSe2 and hypothetical TlCrSSe have been investigated by first-principles all-electron full-potential linearized augmented plane wave plus local orbital (FP-LAPW+lo) method based on density functional theory (DFT). • Total magnetic moment keeps its integer value on a relatively wide range of changes in volume (−10% ÷ 10%) for TlCrS2 and TlCrSSe, while total magnetic moment TlCrSe2 decreases with increasing volume, approaching to integer value 3 μB. • The states at the Fermi level in the case of spin-up channel consist of a hybridization of p-states of the atom S(Se) with d-states of Cr. - Abstract: Half-metallic properties of TlCrS{sub 2}, TlCrSe{sub 2} and hypothetical TlCrSSe have been investigated by first-principles all-electron full-potential linearized augmented plane wave plus local orbital (FP-LAPW+lo) method based on density functional theory (DFT). The results of calculations show that TlCrS{sub 2} and TlCrSSe are half-metals with energy gap (E{sub g}) ∼0.12 eV for spin-down channel. Strong hybridization of p-state of chalchogen and d-state of Cr leads to bonding and antibonding states and subsequently to the appearance of a gap in spin-down channel of TlCrS{sub 2} and TlCrSSe. In the case of TlCrSe{sub 2}, there is a partial hybridization and p-state is partially present in the DOS at Fermi level making this compound nearly half-metallic. The present calculations revealed that total magnetic moment keeps its integer value on a relatively wide range of changes in volume (−10% ÷ 10%) for TlCrS{sub 2} and TlCrSSe, while total magnetic moment of TlCrSe{sub 2} decreases with increasing volume approaching to integer value 3 μB.

Microstructure investigation of NiAl-Cr(Mo) interface in a directionally solidified NiAl-Cr(Mo) eutectic alloyed with refractory metal

International Nuclear Information System (INIS)

Chen, Y.X.; Cui, C.Y.; Guo, J.T.; Li, D.X.

2004-01-01

The microstructure of a directionally solidified NiAl-Cr(Mo) eutectic alloyed with refractory metal in as-processed and heat-treated states has been studied by means of scanning electron microscopy and high resolution electron microscopy (HREM). The microstructure of the NiAl-Cr(Mo) eutectic was characterized by lamellar Cr(Mo) phases embedded within NiAl matrix with common growth direction of . The interface between NiAl and lamellar Cr(Mo) did not have any transition layers. Misfit dislocations were observed at the NiAl-Cr(Mo) interface. In addition to lamellar Cr(Mo) phases, coherent Cr(Mo, Ni, Al) precipitates and NiAl precipitates were also observed in the NiAl matrix and lamellar Cr(Mo) phases, respectively. After hot isostatic pressing and heat treatment, the NiAl-Cr(Mo) interfaces became smooth and straight. Square array of misfit dislocations was directly observed at the (0 0 1) interface between NiAl and Cr(Mo, Ni, Al) precipitate. The configuration of misfit dislocation network showed a generally good agreement with prediction based on the geometric O-lattice model

75 FR 70254 - PSD and Title V Permitting Guidance for Greenhouse Gases

Science.gov (United States)

2010-11-17

... Guidance for Greenhouse Gases AGENCY: Environmental Protection Agency (EPA). ACTION: Notice of availability..., ``PSD and Title V Permitting Guidance for Greenhouse Gases'' on its significant guidance Internet Web... guidance titled, ``PSD and Title V Permitting Guidance for Greenhouse Gases.'' This document has been...

The effect of various grading scales on student grade point averages.

Science.gov (United States)

Barnes, Kelli D; Buring, Shauna M

2012-04-10

To investigate changes in and the impact of grading scales from 2005 to 2010 and explore pharmacy faculty and student perceptions of whole-letter and plus/minus grading scales on cumulative grade point averages (GPAs) in required courses. Grading scales used in 2010 at the University of Cincinnati College of Pharmacy were retrospectively identified and compared to those used in 2005. Mean GPA was calculated using a whole-letter grading scale and a plus/minus grading scale to determine the impact of scales on GPA. Faculty members and students were surveyed regarding their perceptions of plus/minus grading. Nine unique grading scales were used throughout the curriculum, including plus/minus (64%) and whole-letter (21%) grading scales. From 2005 to 2010 there was transition from use of predominantly whole-letter scales to plus/minus grading scales. The type of grading scale used did not affect the mean cumulative GPA. Students preferred use of a plus-only grading scale while faculty members preferred use of a plus/minus grading scale. The transition from whole-letter grading to plus/minus grading in courses from 2005 to 2010 reflects pharmacy faculty members' perception that plus/minus grading allows for better differentiation between students' performances.

MRI differentiation of low-grade from high-grade appendicular chondrosarcoma

International Nuclear Information System (INIS)

Douis, Hassan; Singh, Leanne; Saifuddin, Asif

2014-01-01

To identify magnetic resonance imaging (MRI) features which differentiate low-grade chondral lesions (atypical cartilaginous tumours/grade 1 chondrosarcoma) from high-grade chondrosarcomas (grade 2, grade 3 and dedifferentiated chondrosarcoma) of the major long bones. We identified all patients treated for central atypical cartilaginous tumours and central chondrosarcoma of major long bones (humerus, femur, tibia) over a 13-year period. The MRI studies were assessed for the following features: bone marrow oedema, soft tissue oedema, bone expansion, cortical thickening, cortical destruction, active periostitis, soft tissue mass and tumour length. The MRI-features were compared with the histopathological tumour grading using univariate, multivariate logistic regression and receiver operating characteristic curve (ROC) analyses. One hundred and seventy-nine tumours were included in this retrospective study. There were 28 atypical cartilaginous tumours, 79 grade 1 chondrosarcomas, 36 grade 2 chondrosarcomas, 13 grade 3 chondrosarcomas and 23 dedifferentiated chondrosarcomas. Multivariate analysis demonstrated that bone expansion (P = 0.001), active periostitis (P = 0.001), soft tissue mass (P < 0.001) and tumour length (P < 0.001) were statistically significant differentiating factors between low-grade and high-grade chondral lesions with an area under the ROC curve of 0.956. On MRI, bone expansion, active periostitis, soft tissue mass and tumour length can reliably differentiate high-grade chondrosarcomas from low-grade chondral lesions of the major long bones. (orig.)

MRI differentiation of low-grade from high-grade appendicular chondrosarcoma

Energy Technology Data Exchange (ETDEWEB)

Douis, Hassan; Singh, Leanne; Saifuddin, Asif [The Royal National Orthopaedic Hospital NHS Trust, Department of Radiology, Stanmore, Middlesex (United Kingdom)

2014-01-15

To identify magnetic resonance imaging (MRI) features which differentiate low-grade chondral lesions (atypical cartilaginous tumours/grade 1 chondrosarcoma) from high-grade chondrosarcomas (grade 2, grade 3 and dedifferentiated chondrosarcoma) of the major long bones. We identified all patients treated for central atypical cartilaginous tumours and central chondrosarcoma of major long bones (humerus, femur, tibia) over a 13-year period. The MRI studies were assessed for the following features: bone marrow oedema, soft tissue oedema, bone expansion, cortical thickening, cortical destruction, active periostitis, soft tissue mass and tumour length. The MRI-features were compared with the histopathological tumour grading using univariate, multivariate logistic regression and receiver operating characteristic curve (ROC) analyses. One hundred and seventy-nine tumours were included in this retrospective study. There were 28 atypical cartilaginous tumours, 79 grade 1 chondrosarcomas, 36 grade 2 chondrosarcomas, 13 grade 3 chondrosarcomas and 23 dedifferentiated chondrosarcomas. Multivariate analysis demonstrated that bone expansion (P = 0.001), active periostitis (P = 0.001), soft tissue mass (P < 0.001) and tumour length (P < 0.001) were statistically significant differentiating factors between low-grade and high-grade chondral lesions with an area under the ROC curve of 0.956. On MRI, bone expansion, active periostitis, soft tissue mass and tumour length can reliably differentiate high-grade chondrosarcomas from low-grade chondral lesions of the major long bones. (orig.)

TEM Studies of Boron-Modified 17Cr-7Ni Precipitation-Hardenable Stainless Steel via Rapid Solidification Route

Science.gov (United States)

Gupta, Ankur; Bhargava, A. K.; Tewari, R.; Tiwari, A. N.

2013-09-01

Commercial grade 17Cr-7Ni precipitation-hardenable stainless steel has been modified by adding boron in the range 0.45 to 1.8 wt pct and using the chill block melt-spinning technique of rapid solidification (RS). Application of RS has been found to increase the solid solubility of boron and hardness of 17Cr-7Ni precipitation-hardenable stainless steel. The hardness of the boron-modified rapidly solidified alloys has been found to increase up to ~280 pct after isochronal aging to peak hardness. A TEM study has been carried out to understand the aging behavior. The presence of M23(B,C)6 and M2(B,C) borocarbides and epsilon-carbide in the matrix of austenite and ferrite with a change in heat treatment temperature has been observed. A new equation for Creq is also developed which includes the boron factor on ferrite phase stability. The study also emphasizes that aluminum only takes part in ferrite phase stabilization and remains in the solution.

Region 7 Title V facilities

Data.gov (United States)

U.S. Environmental Protection Agency — This web map shows the Region 7 Title V facilities (Clean Air Act major sources), any Class I areas within 300 km of R7 States, and any Tribal areas within 50 miles...

7 CFR 810.404 - Grades and grade requirements for corn.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Grades and grade requirements for corn. 810.404... OFFICIAL UNITED STATES STANDARDS FOR GRAIN United States Standards for Corn Principles Governing the Application of Standards § 810.404 Grades and grade requirements for corn. Grade Minimum test weight per...

High-pressure BaCrO_3 polytypes and the 5H–BaCrO_2_._8 phase

International Nuclear Information System (INIS)

Arévalo-López, Angel M.; Paul Attfield, J.

2015-01-01

Polytypism of BaCrO_3 perovskites has been investigated at 900–1100 °C and pressures up to 22 GPa. Hexagonal 5H, 4H, and 6H perovskites are observed with increasing pressure, and the cubic 3C perovskite (a=3.99503(1) Å) is observed in bulk form for the first time at 19–22 GPa. An oxygen-deficient material with limiting composition 5H–BaCrO_2_._8 is synthesised at 1200 °C under ambient pressure. This contains double tetrahedral Cr"4"+ layers and orders antiferromagnetically below 260 K with a (0 0 1/2) magnetic structure. - Graphical abstract: Hexagonal 5H, 4H, and 6H perovskites polytypes of BaCrO_3 are observed with increasing pressure and the cubic 3C perovskite is stabilised in bulk form for the first time at 19–22 GPa. Oxygen-deficient 5H–BaCrO_2_._8 synthesised at ambient pressure contains double tetrahedral Cr"4"+ layers and orders antiferromagnetically below 260 K with a (0 0 1/2) magnetic structure.

Erosion-oxidation behavior of thermal sprayed Ni20Cr alloy and WC and Cr3C2 cermet coatings

Directory of Open Access Journals (Sweden)

Clarice Terui Kunioshi

2005-06-01

Full Text Available An apparatus to conduct high temperature erosion-oxidation studies up to 850 °C and with particle impact velocities up to 15 m.s-1 was designed and constructed in the Corrosion Laboratories of IPEN. The erosion-oxidation behavior of high velocity oxy fuel (HVOF sprayed alloy and cermet coatings of Ni20Cr, WC 20Cr7Ni and Cr3C2 Ni20Cr on a steel substrate has been studied. Details of this apparatus and the erosion-oxidation behavior of these coatings are presented and discussed. The erosion-oxidation behavior of HVOF coated Cr3C2 25(Ni20Cr was better than that of WC 20Cr7Ni, and the erosion-oxidation regimes have been identified for these coatings at particle impact velocity of 3.5 m.s-1, impact angle of 90° and temperatures in the range 500 to 850 °C.