WorldWideScience

Sample records for tissue spatial layout

  1. Auditory Spatial Layout

    Science.gov (United States)

    Wightman, Frederic L.; Jenison, Rick

    1995-01-01

    All auditory sensory information is packaged in a pair of acoustical pressure waveforms, one at each ear. While there is obvious structure in these waveforms, that structure (temporal and spectral patterns) bears no simple relationship to the structure of the environmental objects that produced them. The properties of auditory objects and their layout in space must be derived completely from higher level processing of the peripheral input. This chapter begins with a discussion of the peculiarities of acoustical stimuli and how they are received by the human auditory system. A distinction is made between the ambient sound field and the effective stimulus to differentiate the perceptual distinctions among various simple classes of sound sources (ambient field) from the known perceptual consequences of the linear transformations of the sound wave from source to receiver (effective stimulus). Next, the definition of an auditory object is dealt with, specifically the question of how the various components of a sound stream become segregated into distinct auditory objects. The remainder of the chapter focuses on issues related to the spatial layout of auditory objects, both stationary and moving.

  2. Spatial layout affects speed discrimination

    Science.gov (United States)

    Verghese, P.; Stone, L. S.

    1997-01-01

    We address a surprising result in a previous study of speed discrimination with multiple moving gratings: discrimination thresholds decreased when the number of stimuli was increased, but remained unchanged when the area of a single stimulus was increased [Verghese & Stone (1995). Vision Research, 35, 2811-2823]. In this study, we manipulated the spatial- and phase relationship between multiple grating patches to determine their effect on speed discrimination thresholds. In a fusion experiment, we merged multiple stimulus patches, in stages, into a single patch. Thresholds increased as the patches were brought closer and their phase relationship was adjusted to be consistent with a single patch. Thresholds increased further still as these patches were fused into a single patch. In a fission experiment, we divided a single large patch into multiple patches by superimposing a cross with luminance equal to that of the background. Thresholds decreased as the large patch was divided into quadrants and decreased further as the quadrants were maximally separated. However, when the cross luminance was darker than the background, it was perceived as an occluder and thresholds, on average, were unchanged from that for the single large patch. A control experiment shows that the observed trend in discrimination thresholds is not due to the differences in perceived speed of the stimuli. These results suggest that the parsing of the visual image into entities affects the combination of speed information across space, and that each discrete entity effectively provides a single independent estimate of speed.

  3. Layout Geometry in Encoding and Retrieval of Spatial Memory

    Science.gov (United States)

    Mou, Weimin; Liu, Xianyun; McNamara, Timothy P.

    2009-01-01

    Two experiments investigated whether the spatial reference directions that are used to specify objects' locations in memory can be solely determined by layout geometry. Participants studied a layout of objects from a single viewpoint while their eye movements were recorded. Subsequently, participants used memory to make judgments of relative…

  4. The Influence of Environmental Spatial Layout on Perceived Lightness

    Science.gov (United States)

    Kanari, Kei; Inagami, Makoto; Kaneko, Hirohiko

    2011-01-01

    It is obvious that perceived lightness of a surface depends on the surrounding luminance distribution in 2D and 3D. These effects are usually explained by the mechanisms at relatively low level of visual system. However, there seems to be a relation between the illuminance and spatial layout of the scene regardless of the surrounding luminance distribution. If this is valid, perceived lightness of a surface in the scene could be influenced by the spatial layout in the scene. In this research, we investigated the relation between the perceived lightness of surface and the spatial layout of the scene. The subject matched the lightness of test patch presented on a natural picture with various spatial layout to that of comparison stimulus presented on a uniform gray background. The mean luminance of the surround stimuli were the same and the local contrast between the text patch and the surround was kept constant. Results showed that the perceived lightness of a stimulus depended on the spatial structure presented in the background. This result indicates that the spatial layout of the scene is related to the illuminance of that and influenced on perceived lightness.

  5. Representing Spatial Layout According to Intrinsic Frames of Reference.

    Science.gov (United States)

    Xie, Chaoxiang; Li, Shiyi; Tao, Weidong; Wei, Yiping; Sun, Hong-Jin

    2017-01-01

    Mou and McNamara have suggested that object locations are represented according to intrinsic reference frames. In three experiments, we investigated the limitations of intrinsic reference frames as a mean to represent object locations in spatial memory. Participants learned the locations of seven or eight common objects in a rectangular room and then made judgments of relative direction based on their memory of the layout. The results of all experiments showed that when all objects were positioned regularly, judgments of relative direction were faster or more accurate for novel headings that were aligned with the primary intrinsic structure than for other novel headings; however, when one irregularly positioned object was added to the layout, this advantage was eliminated. The experiments further indicated that with a single view at study, participants could represent the layout from either an egocentric orientation or a different orientation, according to experimental instructions. Together, these results suggest that environmental reference frames and intrinsic axes can influence performance for novel headings, but their role in spatial memory depends on egocentric experience, layout regularity, and instructions.

  6. The perception of spatial layout in real and virtual worlds.

    Science.gov (United States)

    Arthur, E J; Hancock, P A; Chrysler, S T

    1997-01-01

    As human-machine interfaces grow more immersive and graphically-oriented, virtual environment systems become more prominent as the medium for human-machine communication. Often, virtual environments (VE) are built to provide exact metrical representations of existing or proposed physical spaces. However, it is not known how individuals develop representational models of these spaces in which they are immersed and how those models may be distorted with respect to both the virtual and real-world equivalents. To evaluate the process of model development, the present experiment examined participant's ability to reproduce a complex spatial layout of objects having experienced them previously under different viewing conditions. The layout consisted of nine common objects arranged on a flat plane. These objects could be viewed in a free binocular virtual condition, a free binocular real-world condition, and in a static monocular view of the real world. The first two allowed active exploration of the environment while the latter condition allowed the participant only a passive opportunity to observe from a single viewpoint. Viewing conditions were a between-subject variable with 10 participants randomly assigned to each condition. Performance was assessed using mapping accuracy and triadic comparisons of relative inter-object distances. Mapping results showed a significant effect of viewing condition where, interestingly, the static monocular condition was superior to both the active virtual and real binocular conditions. Results for the triadic comparisons showed a significant interaction for gender by viewing condition in which males were more accurate than females. These results suggest that the situation model resulting from interaction with a virtual environment was indistinguishable from interaction with real objects at least within the constraints of the present procedure.

  7. Mental Layout Extrapolations Prime Spatial Processing of Scenes

    Science.gov (United States)

    Gottesman, Carmela V.

    2011-01-01

    Four experiments examined whether scene processing is facilitated by layout representation, including layout that was not perceived but could be predicted based on a previous partial view (boundary extension). In a priming paradigm (after Sanocki, 2003), participants judged objects' distances in photographs. In Experiment 1, full scenes (target),…

  8. Factors driving the spatial layout of distribution channels

    NARCIS (Netherlands)

    Onstein, A.T.C.; Ektesaby, M.; Rezaei, J.; Tavasszy, L.A.; van Damme, D.A.

    2017-01-01

    Research statement Our study analyses the factors that drive decision-making on distribution structures, including the layout of distribution channels and the locations of distribution centres. Distribution is a primary firm activity, which strongly influences logistics costs and logistics

  9. A spatial multi-objective optimization model for sustainable urban wastewater system layout planning.

    Science.gov (United States)

    Dong, X; Zeng, S; Chen, J

    2012-01-01

    Design of a sustainable city has changed the traditional centralized urban wastewater system towards a decentralized or clustering one. Note that there is considerable spatial variability of the factors that affect urban drainage performance including urban catchment characteristics. The potential options are numerous for planning the layout of an urban wastewater system, which are associated with different costs and local environmental impacts. There is thus a need to develop an approach to find the optimal spatial layout for collecting, treating, reusing and discharging the municipal wastewater of a city. In this study, a spatial multi-objective optimization model, called Urban wastewateR system Layout model (URL), was developed. It is solved by a genetic algorithm embedding Monte Carlo sampling and a series of graph algorithms. This model was illustrated by a case study in a newly developing urban area in Beijing, China. Five optimized system layouts were recommended to the local municipality for further detailed design.

  10. Spatial layout optimization design of multi-type LEDs lighting source based on photoelectrothermal coupling theory

    Science.gov (United States)

    Xue, Lingyun; Li, Guang; Chen, Qingguang; Rao, Huanle; Xu, Ping

    2018-03-01

    Multiple LED-based spectral synthesis technology has been widely used in the fields of solar simulator, color mixing, and artificial lighting of plant factory and so on. Generally, amounts of LEDs are spatially arranged with compact layout to obtain the high power density output. Mutual thermal spreading among LEDs will produce the coupled thermal effect which will additionally increase the junction temperature of LED. Affected by the Photoelectric thermal coupling effect of LED, the spectrum of LED will shift and luminous efficiency will decrease. Correspondingly, the spectral synthesis result will mismatch. Therefore, thermal management of LED spatial layout plays an important role for multi-LEDs light source system. In the paper, the thermal dissipation network topology model considering the mutual thermal spreading effect among the LEDs is proposed for multi-LEDs system with various types of power. The junction temperature increment cased by the thermal coupling has the great relation with the spatial arrangement. To minimize the thermal coupling effect, an optimized method of LED spatial layout for the specific light source structure is presented and analyzed. The results showed that layout of LED with high-power are arranged in the corner and low-power in the center. Finally, according to this method, it is convenient to determine the spatial layout of LEDs in a system having any kind of light source structure, and has the advantages of being universally applicable to facilitate adjustment.

  11. Combining Multiple Forms Of Visual Information To Specify Contact Relations In Spatial Layout

    Science.gov (United States)

    Sedgwick, Hal A.

    1990-03-01

    An expert system, called Layout2, has been described, which models a subset of available visual information for spatial layout. The system is used to examine detailed interactions between multiple, partially redundant forms of information in an environment-centered geometrical model of an environment obeying certain rather general constraints. This paper discusses the extension of Layout2 to include generalized contact relations between surfaces. In an environment-centered model, the representation of viewer-centered distance is replaced by the representation of environmental location. This location information is propagated through the representation of the environment by a network of contact relations between contiguous surfaces. Perspective information interacts with other forms of information to specify these contact relations. The experimental study of human perception of contact relations in extended spatial layouts is also discussed. Differences between human results and Layout2 results reveal limitations in the human ability to register available information; they also point to the existence of certain forms of information not yet formalized in Layout2.

  12. The Characteristics Of Malay House Spatial Layout Of Pekanbaru In Accordance With Islamic Values

    Science.gov (United States)

    Samra, Boby

    2017-12-01

    House is not only is a place to get rest and do activities bu also treated as a pride for the Malay community. The values contained in the spatial layout of the house have specific meaning to the owners. This makes the Malay house becomes the symbol of pride to uphold the “tuah” and dignity of the owner. This research is conducted using qualitative approach through management and data management available through several methods such as observation, interview, documentation and group discussion. This is expected to provide understanding of the perception of Islam dealing with the characteristics of the spatial layout of the Malay house of Pekanbaru.

  13. Considering the Spatial Layout Information of Bag of Features (BoF) Framework for Image Classification.

    Science.gov (United States)

    Mu, Guangyu; Liu, Ying; Wang, Limin

    2015-01-01

    The spatial pooling method such as spatial pyramid matching (SPM) is very crucial in the bag of features model used in image classification. SPM partitions the image into a set of regular grids and assumes that the spatial layout of all visual words obey the uniform distribution over these regular grids. However, in practice, we consider that different visual words should obey different spatial layout distributions. To improve SPM, we develop a novel spatial pooling method, namely spatial distribution pooling (SDP). The proposed SDP method uses an extension model of Gauss mixture model to estimate the spatial layout distributions of the visual vocabulary. For each visual word type, SDP can generate a set of flexible grids rather than the regular grids from the traditional SPM. Furthermore, we can compute the grid weights for visual word tokens according to their spatial coordinates. The experimental results demonstrate that SDP outperforms the traditional spatial pooling methods, and is competitive with the state-of-the-art classification accuracy on several challenging image datasets.

  14. Spatial Layout of Multi-Environment Test Sites: A Case Study of Maize in Jilin Province

    Directory of Open Access Journals (Sweden)

    Zuliang Zhao

    2018-05-01

    Full Text Available Variety regional tests based on multiple environments play a critical role in understanding the high yield and adaptability of new crop varieties. However, the current approach mainly depends on experience from breeding experts and is difficulty to promote because of inconsistency between testing and actual situation. We propose a spatial layout method based on the existing systematic regional test network. First, the method of spatial clustering was used to cluster the planting environment. Then, we used spatial stratified sampling to determine the minimum number of test sites in each type of environment. Finally, combined with the factors such as the convenience of transportation and the planting area, we used spatial balance sampling to generate the layout of multi-environment test sites. We present a case study for maize in Jilin Province and show the utility of the method with an accuracy of about 94.5%. The experimental results showed that 66.7% of sites are located in the same county and the unbalanced layout of original sites is improved. Furthermore, we conclude that the set of operational technical ideas for carrying out the layout of multi-environment test sites based on crop varieties in this paper can be applied to future research.

  15. Contextual Cueing Effect in Spatial Layout Defined by Binocular Disparity

    Science.gov (United States)

    Zhao, Guang; Zhuang, Qian; Ma, Jie; Tu, Shen; Liu, Qiang; Sun, Hong-jin

    2017-01-01

    Repeated visual context induces higher search efficiency, revealing a contextual cueing effect, which depends on the association between the target and its visual context. In this study, participants performed a visual search task where search items were presented with depth information defined by binocular disparity. When the 3-dimensional (3D) configurations were repeated over blocks, the contextual cueing effect was obtained (Experiment 1). When depth information was in chaos over repeated configurations, visual search was not facilitated and the contextual cueing effect largely crippled (Experiment 2). However, when we made the search items within a tiny random displacement in the 2-dimentional (2D) plane but maintained the depth information constant, the contextual cueing was preserved (Experiment 3). We concluded that the contextual cueing effect was robust in the context provided by 3D space with stereoscopic information, and more importantly, the visual system prioritized stereoscopic information in learning of spatial information when depth information was available. PMID:28912739

  16. Deconstructing visual scenes in cortex: gradients of object and spatial layout information.

    Science.gov (United States)

    Harel, Assaf; Kravitz, Dwight J; Baker, Chris I

    2013-04-01

    Real-world visual scenes are complex cluttered, and heterogeneous stimuli engaging scene- and object-selective cortical regions including parahippocampal place area (PPA), retrosplenial complex (RSC), and lateral occipital complex (LOC). To understand the unique contribution of each region to distributed scene representations, we generated predictions based on a neuroanatomical framework adapted from monkey and tested them using minimal scenes in which we independently manipulated both spatial layout (open, closed, and gradient) and object content (furniture, e.g., bed, dresser). Commensurate with its strong connectivity with posterior parietal cortex, RSC evidenced strong spatial layout information but no object information, and its response was not even modulated by object presence. In contrast, LOC, which lies within the ventral visual pathway, contained strong object information but no background information. Finally, PPA, which is connected with both the dorsal and the ventral visual pathway, showed information about both objects and spatial backgrounds and was sensitive to the presence or absence of either. These results suggest that 1) LOC, PPA, and RSC have distinct representations, emphasizing different aspects of scenes, 2) the specific representations in each region are predictable from their patterns of connectivity, and 3) PPA combines both spatial layout and object information as predicted by connectivity.

  17. Research on the Heat Dissipation Characteristics of Lithium Battery Spatial Layout in an AUV

    Directory of Open Access Journals (Sweden)

    Zhaoyong Mao

    2016-01-01

    Full Text Available To meet the power demand requirements of autonomous underwater vehicles (AUVs, the power supply is generally composed of a large number of high-energy lithium battery groups. The lithium battery heat dissipation properties not only affect the underwater vehicle performance but also bring some security risks. Based on the widespread application of lithium batteries, lithium batteries in an AUV are taken as an example to investigate the heat dissipation characteristics of the lithium battery spatial layout in an AUV. With the aim of increasing the safety of lithium batteries, a model is developed for the heat transfer process based on the energy conservation equation, and the battery heat dissipation characteristics of the spatial layout are analyzed. The results indicate that the most suitable distance between the cells and the cross arrangement is better than the sequence arrangement in terms of cooling characteristics. The temperature gradient and the temperature change inside the cabin with time are primarily affected by the navigation speed, but they have little relationship with the environmental temperature.

  18. Evaluation of realistic layouts for next generation on-scalp MEG: spatial information density maps.

    Science.gov (United States)

    Riaz, Bushra; Pfeiffer, Christoph; Schneiderman, Justin F

    2017-08-01

    While commercial magnetoencephalography (MEG) systems are the functional neuroimaging state-of-the-art in terms of spatio-temporal resolution, MEG sensors have not changed significantly since the 1990s. Interest in newer sensors that operate at less extreme temperatures, e.g., high critical temperature (high-T c ) SQUIDs, optically-pumped magnetometers, etc., is growing because they enable significant reductions in head-to-sensor standoff (on-scalp MEG). Various metrics quantify the advantages of on-scalp MEG, but a single straightforward one is lacking. Previous works have furthermore been limited to arbitrary and/or unrealistic sensor layouts. We introduce spatial information density (SID) maps for quantitative and qualitative evaluations of sensor arrays. SID-maps present the spatial distribution of information a sensor array extracts from a source space while accounting for relevant source and sensor parameters. We use it in a systematic comparison of three practical on-scalp MEG sensor array layouts (based on high-T c SQUIDs) and the standard Elekta Neuromag TRIUX magnetometer array. Results strengthen the case for on-scalp and specifically high-T c SQUID-based MEG while providing a path for the practical design of future MEG systems. SID-maps are furthermore general to arbitrary magnetic sensor technologies and source spaces and can thus be used for design and evaluation of sensor arrays for magnetocardiography, magnetic particle imaging, etc.

  19. An Exploration of Eye Movements when Reading Texts with Atypical Spatial Layouts

    Directory of Open Access Journals (Sweden)

    F Hermens

    2012-07-01

    Full Text Available In two experiments we explored eye movements that people make when looking at texts with an atypical spatial layout. In the first experiment, participants repeatedly viewed the same piece of text, containing sections in different languages and printed using different fonts and reading directions, while they answered different questions about what they saw. In agreement with earlier studies showing significant differences in gaze patterns across different tasks, we found that reading was strongly influenced by the questions that participants tried to answer. In the second experiment, we examined gaze patterns for different types of poems while participants performed a single task: To rate their appreciation of the poem. Poems were either in the typical form, with short lines all aligned to the left, or they were in an atypical form (“graphical poem”, with the text dispersed across the page, in different fonts, reading directions, and size. Half of the poems were from an artist known for his graphical poems, the other half were from different authors who posted their poems on a webpage. All these poems were presented in a typical and an atypical form. Participants rated the poems from the web more highly, but took less time to inspect them. Whether the poem was in a typical or an atypical layout did not influence the ratings, even though longer inspection times were found for the atypical forms. Eye movement parameters, such as fixation duration and saccade amplitude, were relatively unaffected by the layout of the poems, although some additional larger amplitude saccades could be observed for the atypical forms.

  20. Study of an optimization approach for a disposal tunnel layout, taking into account the geological environment with spatially heterogeneous characteristics

    International Nuclear Information System (INIS)

    Suyama, Yasuhiro; Toida, Masaru; Yanagizawa, Koichi

    2009-01-01

    The geological environment has spatially heterogeneous characteristics with varied host rock types, fractures and so on. In this case the generic disposal tunnel layout, which has been designed by JNC, is not the most suitable for HLW disposal in Japan. The existence of spatially heterogeneous characteristics means that in the repository region there exist sub-regions that are more favourable from the perspective of long-term safety and ones that are less favourable. In order that the spatially heterogeneous environment itself may be utilized most effectively as a natural barrier system, an alternative design of disposal tunnel layout is required. Focusing on the geological environment with spatially heterogeneous characteristics, the authors have developed an alternative design of disposal tunnel layout. The alternative design adopts an optimization approach using a variable disposal tunnel layout. The optimization approach minimizes the number of locations where major water-conducting fractures are intersected, and maximizes the number of emplacement locations for waste packages. This paper will outline the variable disposal tunnel layout and its applicability.

  1. Non-retinotopic feature processing in the absence of retinotopic spatial layout and the construction of perceptual space from motion.

    Science.gov (United States)

    Ağaoğlu, Mehmet N; Herzog, Michael H; Oğmen, Haluk

    2012-10-15

    The spatial representation of a visual scene in the early visual system is well known. The optics of the eye map the three-dimensional environment onto two-dimensional images on the retina. These retinotopic representations are preserved in the early visual system. Retinotopic representations and processing are among the most prevalent concepts in visual neuroscience. However, it has long been known that a retinotopic representation of the stimulus is neither sufficient nor necessary for perception. Saccadic Stimulus Presentation Paradigm and the Ternus-Pikler displays have been used to investigate non-retinotopic processes with and without eye movements, respectively. However, neither of these paradigms eliminates the retinotopic representation of the spatial layout of the stimulus. Here, we investigated how stimulus features are processed in the absence of a retinotopic layout and in the presence of retinotopic conflict. We used anorthoscopic viewing (slit viewing) and pitted a retinotopic feature-processing hypothesis against a non-retinotopic feature-processing hypothesis. Our results support the predictions of the non-retinotopic feature-processing hypothesis and demonstrate the ability of the visual system to operate non-retinotopically at a fine feature processing level in the absence of a retinotopic spatial layout. Our results suggest that perceptual space is actively constructed from the perceptual dimension of motion. The implications of these findings for normal ecological viewing conditions are discussed. 2012 Elsevier Ltd. All rights reserved

  2. Research on the optimization of air quality monitoring station layout based on spatial grid statistical analysis method.

    Science.gov (United States)

    Li, Tianxin; Zhou, Xing Chen; Ikhumhen, Harrison Odion; Difei, An

    2018-05-01

    In recent years, with the significant increase in urban development, it has become necessary to optimize the current air monitoring stations to reflect the quality of air in the environment. Highlighting the spatial representation of some air monitoring stations using Beijing's regional air monitoring station data from 2012 to 2014, the monthly mean particulate matter concentration (PM10) in the region was calculated and through the IDW interpolation method and spatial grid statistical method using GIS, the spatial distribution of PM10 concentration in the whole region was deduced. The spatial distribution variation of districts in Beijing using the gridding model was performed, and through the 3-year spatial analysis, PM10 concentration data including the variation and spatial overlay (1.5 km × 1.5 km cell resolution grid), the spatial distribution result obtained showed that the total PM10 concentration frequency variation exceeded the standard. It is very important to optimize the layout of the existing air monitoring stations by combining the concentration distribution of air pollutants with the spatial region using GIS.

  3. Walk, Look, Remember: The Influence of the Gallery's Spatial Layout on Human Memory for an Art Exhibition.

    Science.gov (United States)

    Krukar, Jakub

    2014-09-01

    The spatial organisation of museums and its influence on the visitor experience has been the subject of numerous studies. Previous research, despite reporting some actual behavioural correlates, rarely had the possibility to investigate the cognitive processes of the art viewers. In the museum context, where spatial layout is one of the most powerful curatorial tools available, attention and memory can be measured as a means of establishing whether or not the gallery fulfils its function as a space for contemplating art. In this exploratory experiment, 32 participants split into two groups explored an experimental, non-public exhibition and completed two unanticipated memory tests afterwards. The results show that some spatial characteristics of an exhibition can inhibit the recall of pictures and shift the focus to perceptual salience of the artworks.

  4. Walk, Look, Remember: The Influence of the Gallery’s Spatial Layout on Human Memory for an Art Exhibition

    Directory of Open Access Journals (Sweden)

    Jakub Krukar

    2014-07-01

    Full Text Available The spatial organisation of museums and its influence on the visitor experience has been the subject of numerous studies. Previous research, despite reporting some actual behavioural correlates, rarely had the possibility to investigate the cognitive processes of the art viewers. In the museum context, where spatial layout is one of the most powerful curatorial tools available, attention and memory can be measured as a means of establishing whether or not the gallery fulfils its function as a space for contemplating art. In this exploratory experiment, 32 participants split into two groups explored an experimental, non-public exhibition and completed two unanticipated memory tests afterwards. The results show that some spatial characteristics of an exhibition can inhibit the recall of pictures and shift the focus to perceptual salience of the artworks.

  5. Layout Construction

    DEFF Research Database (Denmark)

    Frandsen, Gudmund Skovbjerg; Palsberg, Jens; Schmidt, Erik Meineche

    We design a system for generating newspaper layout proposals. The input to the system consists of editorial information (text, pictures, etc) and style information (non-editorial information that specifies the aesthetic appearance of a layout). We consider the automation of layout construction...... to pose two main problems. One problem consists in optimizing the layout with respect to the constraints and preferences specified in the style information. Another problem consists in finding a representation of the style information that both supports its use in the combinatorial optimization...

  6. Measuring the impact of spatial network layout on community social cohesion: a cross-sectional study.

    Science.gov (United States)

    Cooper, Crispin H V; Fone, David L; Chiaradia, Alain J F

    2014-04-11

    There is now a substantial body of research suggesting that social cohesion, a collective characteristic measured by the levels of trust, reciprocity and formation of strong social bonds within communities, is an important factor in determining health. Of particular interest is the extent to which factors in the built environment facilitate, or impede, the development of social bonds. Severance is a characteristic of physical environments which is hypothesized to inhibit cohesion. In the current study we test a number of characteristics of spatial networks which could be hypothesized to relate either to severance, or directly to community cohesion. Particular focus is given to our most promising variable for further analysis (Convex Hull Maximum Radius 600 m). In the current study we analysed social cohesion as measured at Enumeration District level, aggregated from a survey of 10,892 individuals aged 18 to 74 years in the Caerphilly Health and Social Needs Cohort Study, 2001. In a data mining process we test 16 network variables on multiple scales. The variable showing the most promise is validated in a test on an independent data set. We then conduct a multivariate regression also including Townsend deprivation scores and urban/rural status as predictor variables for social cohesion. We find convex hull maximum radius at a 600 m scale to have a small but highly significant correlation with social cohesion on both data sets. Deprivation has a stronger effect. Splitting the analysis by tertile of deprivation, we find that the effect of severance as measured by this variable is strongest in the most deprived areas. A range of spatial scales are tested, with the strongest effects being observed at scales that match typical walking distances. We conclude that physical connectivity as measured in this paper has a significant effect on social cohesion, and that our measure is unlikely to proxy either deprivation or the urban/rural status of communities. Possible

  7. Course Layout

    OpenAIRE

    2005-01-01

    present roll Presentation roll Interactive Media Element This is an interactive diagram of a MATLAB course layout covering 16 topics in 4 different main areas: Basics of MATLAB, Numerical Methods in MATLAB, Symbolic Manipulations in MATLAB, Mathematical Modeling in MATLAB and Simulink AE2440 Introduction to Digital Computation

  8. Human factors issues and approaches in the spatial layout of a space station control room, including the use of virtual reality as a design analysis tool

    Science.gov (United States)

    Hale, Joseph P., II

    1994-01-01

    Human Factors Engineering support was provided for the 30% design review of the late Space Station Freedom Payload Control Area (PCA). The PCA was to be the payload operations control room, analogous to the Spacelab Payload Operations Control Center (POCC). This effort began with a systematic collection and refinement of the relevant requirements driving the spatial layout of the consoles and PCA. This information was used as input for specialized human factors analytical tools and techniques in the design and design analysis activities. Design concepts and configuration options were developed and reviewed using sketches, 2-D Computer-Aided Design (CAD) drawings, and immersive Virtual Reality (VR) mockups.

  9. Do you know where your fingers have been? Explicit knowledge of the spatial layout of the keyboard in skilled typists.

    Science.gov (United States)

    Liu, Xianyun; Crump, Matthew J C; Logan, Gordon D

    2010-06-01

    Two experiments evaluated skilled typists' ability to report knowledge about the layout of keys on a standard keyboard. In Experiment 1, subjects judged the relative direction of letters on the computer keyboard. One group of subjects was asked to imagine the keyboard, one group was allowed to look at the keyboard, and one group was asked to type the letter pair before judging relative direction. The imagine group had larger angular error and longer response time than both the look and touch groups. In Experiment 2, subjects placed one key relative to another. Again, the imagine group had larger angular error, larger distance error, and longer response time than the other groups. The two experiments suggest that skilled typists have poor explicit knowledge of key locations. The results are interpreted in terms of a model with two hierarchical parts in the system controlling typewriting.

  10. Facade Layout Symmetrization

    KAUST Repository

    Jiang, Haiyong

    2016-04-11

    We present an automatic algorithm for symmetrizing facade layouts. Our method symmetrizes a given facade layout while minimally modifying the original layout. Based on the principles of symmetry in urban design, we formulate the problem of facade layout symmetrization as an optimization problem. Our system further enhances the regularity of the final layout by redistributing and aligning boxes in the layout. We demonstrate that the proposed solution can generate symmetric facade layouts efficiently. © 2015 IEEE.

  11. Symmetrization of Facade Layouts

    KAUST Repository

    Jiang, Haiyong; Yan, Dong-Ming; Dong, Weiming; Wu, Fuzhang; Nan, Liangliang; Zhang, Xiaopeng

    2016-01-01

    We present an automatic approach for symmetrizing urban facade layouts. Our method can generate a symmetric layout through minimally modifying the original input layout. Based on the principles of symmetry in urban design, we formulate facade layout symmetrization as an optimization problem. Our method further enhances the regularity of the final layout by redistributing and aligning elements in the layout. We demonstrate that the proposed solution can effectively generate symmetric facade layouts.

  12. Facade Layout Symmetrization

    KAUST Repository

    Jiang, Haiyong; Dong, Weiming; Yan, Dongming; Zhang, Xiaopeng

    2016-01-01

    We present an automatic algorithm for symmetrizing facade layouts. Our method symmetrizes a given facade layout while minimally modifying the original layout. Based on the principles of symmetry in urban design, we formulate the problem of facade layout symmetrization as an optimization problem. Our system further enhances the regularity of the final layout by redistributing and aligning boxes in the layout. We demonstrate that the proposed solution can generate symmetric facade layouts efficiently. © 2015 IEEE.

  13. Symmetrization of Facade Layouts

    KAUST Repository

    Jiang, Haiyong

    2016-02-26

    We present an automatic approach for symmetrizing urban facade layouts. Our method can generate a symmetric layout through minimally modifying the original input layout. Based on the principles of symmetry in urban design, we formulate facade layout symmetrization as an optimization problem. Our method further enhances the regularity of the final layout by redistributing and aligning elements in the layout. We demonstrate that the proposed solution can effectively generate symmetric facade layouts.

  14. Spatial distribution of soluble insulin in pig subcutaneous tissue

    DEFF Research Database (Denmark)

    Thomsen, Maria; Rasmussen, Christian Hove; Refsgaard, Hanne H F

    2015-01-01

    in the tomographic reconstructions and the amount of drug in each tissue class was quantified. With a scan time of about 45min per sample, and a robust segmentation it was possible to analyze differences in the spatial drug distribution between several similar injections. It was studied how the drug distribution...

  15. Tissue oxygenation and haemodynamics measurement with spatially resolved NIRS

    Science.gov (United States)

    Zhang, Y.; Scopesi, F.; Serra, G.; Sun, J. W.; Rolfe, P.

    2010-08-01

    We describe the use of Near Infrared Spectroscopy (NIRS) for the non-invasive investigation of changes in haemodynamics and oxygenation of human peripheral tissues. The goal was to measure spatial variations of tissue NIRS oxygenation variables, namely deoxy-haemoglobin (HHb), oxy-haemoglobin (HbO2), total haemoglobin (HbT), and thereby to evaluate the responses of the peripheral circulation to imposed physiological challenges. We present a skinfat- muscle heterogeneous tissue model with varying fat thickness up to 15mm and a Monte Carlo simulation of photon transport within this model. The mean partial path length and the mean photon visit depth in the muscle layer were derived for different source-detector spacing. We constructed NIRS instrumentation comprising of light-emitting diodes (LED) as light sources at four wavelengths, 735nm, 760nm, 810nm and 850nm and sensitive photodiodes (PD) as the detectors. Source-detector spacing was varied to perform measurements at different depths within forearm tissue. Changes in chromophore concentration in response to venous and arterial occlusion were calculated using the modified Lambert-Beer Law. Studies in fat and thin volunteers indicated greater sensitivity in the thinner subjects for the tissue oxygenation measurement in the muscle layer. These results were consistent with those found using Monte Carlo simulation. Overall, the results of this investigation demonstrate the usefulness of the NIRS instrument for deriving spatial information from biological tissues.

  16. The design of the layout of faceted multi-channel electro-optical spatial coordinates measuring instrument for point-like bright objects

    Science.gov (United States)

    Repin, Vladislav A.; Gorbunova, Elena V.; Chertov, Aleksandr N.; Korotaev, Valery V.

    2017-06-01

    For many applied problems it is necessary to obtain information about the situation in a wide angular field in order to measure various parameters of objects: their spatial coordinates, instantaneous velocities, and so on. In this case, one interesting bionic approach can be used - a mosaic (or discrete, otherwise, facet) angular field. Such electro-optical system constructively imitates the visual apparatus of insects: many photodetectors like ommatidia (elements of the facet eye structure) are located on a non-planar surface. Such devices can be used in photogrammetry and aerial photography systems (if the space is sufficient), in the transport sector as vehicle orientation organs, as systems for monitoring in unmanned aerial vehicles, in endoscopy for obtaining comprehensive information on the state of various cavities, in intelligent robotic systems. In this manuscript discusses the advantages and disadvantages of multi-channeled optoelectronic systems with a mosaic angular field, presents possible options for their use, and discusses some of the design procedures performed when developing a layout of a coordinate measuring device.

  17. Content-based image retrieval using spatial layout information in brain tumor T1-weighted contrast-enhanced MR images.

    Science.gov (United States)

    Huang, Meiyan; Yang, Wei; Wu, Yao; Jiang, Jun; Gao, Yang; Chen, Yang; Feng, Qianjin; Chen, Wufan; Lu, Zhentai

    2014-01-01

    This study aims to develop content-based image retrieval (CBIR) system for the retrieval of T1-weighted contrast-enhanced MR (CE-MR) images of brain tumors. When a tumor region is fed to the CBIR system as a query, the system attempts to retrieve tumors of the same pathological category. The bag-of-visual-words (BoVW) model with partition learning is incorporated into the system to extract informative features for representing the image contents. Furthermore, a distance metric learning algorithm called the Rank Error-based Metric Learning (REML) is proposed to reduce the semantic gap between low-level visual features and high-level semantic concepts. The effectiveness of the proposed method is evaluated on a brain T1-weighted CE-MR dataset with three types of brain tumors (i.e., meningioma, glioma, and pituitary tumor). Using the BoVW model with partition learning, the mean average precision (mAP) of retrieval increases beyond 4.6% with the learned distance metrics compared with the spatial pyramid BoVW method. The distance metric learned by REML significantly outperforms three other existing distance metric learning methods in terms of mAP. The mAP of the CBIR system is as high as 91.8% using the proposed method, and the precision can reach 93.1% when the top 10 images are returned by the system. These preliminary results demonstrate that the proposed method is effective and feasible for the retrieval of brain tumors in T1-weighted CE-MR Images.

  18. Content-based image retrieval using spatial layout information in brain tumor T1-weighted contrast-enhanced MR images.

    Directory of Open Access Journals (Sweden)

    Meiyan Huang

    Full Text Available This study aims to develop content-based image retrieval (CBIR system for the retrieval of T1-weighted contrast-enhanced MR (CE-MR images of brain tumors. When a tumor region is fed to the CBIR system as a query, the system attempts to retrieve tumors of the same pathological category. The bag-of-visual-words (BoVW model with partition learning is incorporated into the system to extract informative features for representing the image contents. Furthermore, a distance metric learning algorithm called the Rank Error-based Metric Learning (REML is proposed to reduce the semantic gap between low-level visual features and high-level semantic concepts. The effectiveness of the proposed method is evaluated on a brain T1-weighted CE-MR dataset with three types of brain tumors (i.e., meningioma, glioma, and pituitary tumor. Using the BoVW model with partition learning, the mean average precision (mAP of retrieval increases beyond 4.6% with the learned distance metrics compared with the spatial pyramid BoVW method. The distance metric learned by REML significantly outperforms three other existing distance metric learning methods in terms of mAP. The mAP of the CBIR system is as high as 91.8% using the proposed method, and the precision can reach 93.1% when the top 10 images are returned by the system. These preliminary results demonstrate that the proposed method is effective and feasible for the retrieval of brain tumors in T1-weighted CE-MR Images.

  19. Underground Layout Configuration

    International Nuclear Information System (INIS)

    A. Linden

    2003-01-01

    The purpose of this analysis was to develop an underground layout to support the license application (LA) design effort. In addition, the analysis will be used as the technical basis for the underground layout general arrangement drawings

  20. Reconfigurable layout problem

    NARCIS (Netherlands)

    Meng, G.; Heragu, S.S.; Heragu, S.S.; Zijm, Willem H.M.

    2004-01-01

    This paper addresses the reconfigurable layout problem, which differs from traditional, robust and dynamic layout problems mainly in two aspects: first, it assumes that production data are available only for the current and upcoming production period. Second, it considers queuing performance

  1. Spatial transcriptomics: paving the way for tissue-level systems biology.

    Science.gov (United States)

    Moor, Andreas E; Itzkovitz, Shalev

    2017-08-01

    The tissues in our bodies are complex systems composed of diverse cell types that often interact in highly structured repeating anatomical units. External gradients of morphogens, directional blood flow, as well as the secretion and absorption of materials by cells generate distinct microenvironments at different tissue coordinates. Such spatial heterogeneity enables optimized function through division of labor among cells. Unraveling the design principles that govern this spatial division of labor requires techniques to quantify the entire transcriptomes of cells while accounting for their spatial coordinates. In this review we describe how recent advances in spatial transcriptomics open the way for tissue-level systems biology. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Positron flight in human tissues and its influence on PET image spatial resolution

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez-Crespo, Alejandro; Larsson, Stig A. [Section of Nuclear Medicine, Department of Hospital Physics, Karolinska Hospital, 176 76, Stockholm (Sweden); Medical Radiation Physics, Department of Oncology-Pathology, Stockholm University and Karolinska Institute, Stockholm (Sweden); Andreo, Pedro [Medical Radiation Physics, Department of Oncology-Pathology, Stockholm University and Karolinska Institute, Stockholm (Sweden)

    2004-01-01

    The influence of the positron distance of flight in various human tissues on the spatial resolution in positron emission tomography (PET) was assessed for positrons from carbon-11, nitrogen-13, oxygen-15, fluorine-18, gallium-68 and rubidium-82. The investigation was performed using the Monte Carlo code PENELOPE to simulate the transport of positrons within human compact bone, adipose, soft and lung tissue. The simulations yielded 3D distributions of annihilation origins that were projected on the image plane in order to assess their impact on PET spatial resolution. The distributions obtained were cusp-shaped with long tails rather than Gaussian shaped, thus making conventional full width at half maximum (FWHM) measures uncertain. The full width at 20% of the maximum amplitude (FW20M) of the annihilation distributions yielded more appropriate values for root mean square addition of spatial resolution loss components. Large differences in spatial resolution losses due to the positron flight in various human tissues were found for the selected radionuclides. The contribution to image blur was found to be up to three times larger in lung tissue than in soft tissue or fat and five times larger than in bone tissue. For {sup 18}F, the spatial resolution losses were 0.54 mm in soft tissue and 1.52 mm in lung tissue, compared with 4.10 and 10.5 mm, respectively, for {sup 82}Rb. With lung tissue as a possible exception, the image blur due to the positron flight in all human tissues has a minor impact as long as PET cameras with a spatial resolution of 5-7 mm are used in combination with {sup 18}F-labelled radiopharmaceuticals. However, when ultra-high spatial resolution PET cameras, with 3-4 mm spatial resolution, are applied, especially in combination with other radionuclides, the positron flight may enter as a limiting factor for the total PET spatial resolution - particularly in lung tissue. (orig.)

  3. Positron flight in human tissues and its influence on PET image spatial resolution

    International Nuclear Information System (INIS)

    Sanchez-Crespo, Alejandro; Larsson, Stig A.; Andreo, Pedro

    2004-01-01

    The influence of the positron distance of flight in various human tissues on the spatial resolution in positron emission tomography (PET) was assessed for positrons from carbon-11, nitrogen-13, oxygen-15, fluorine-18, gallium-68 and rubidium-82. The investigation was performed using the Monte Carlo code PENELOPE to simulate the transport of positrons within human compact bone, adipose, soft and lung tissue. The simulations yielded 3D distributions of annihilation origins that were projected on the image plane in order to assess their impact on PET spatial resolution. The distributions obtained were cusp-shaped with long tails rather than Gaussian shaped, thus making conventional full width at half maximum (FWHM) measures uncertain. The full width at 20% of the maximum amplitude (FW20M) of the annihilation distributions yielded more appropriate values for root mean square addition of spatial resolution loss components. Large differences in spatial resolution losses due to the positron flight in various human tissues were found for the selected radionuclides. The contribution to image blur was found to be up to three times larger in lung tissue than in soft tissue or fat and five times larger than in bone tissue. For 18 F, the spatial resolution losses were 0.54 mm in soft tissue and 1.52 mm in lung tissue, compared with 4.10 and 10.5 mm, respectively, for 82 Rb. With lung tissue as a possible exception, the image blur due to the positron flight in all human tissues has a minor impact as long as PET cameras with a spatial resolution of 5-7 mm are used in combination with 18 F-labelled radiopharmaceuticals. However, when ultra-high spatial resolution PET cameras, with 3-4 mm spatial resolution, are applied, especially in combination with other radionuclides, the positron flight may enter as a limiting factor for the total PET spatial resolution - particularly in lung tissue. (orig.)

  4. Site Recommendation Subsurface Layout

    International Nuclear Information System (INIS)

    C.L. Linden

    2000-01-01

    The purpose of this analysis is to develop a Subsurface Facility layout that is capable of accommodating the statutory capacity of 70,000 metric tons of uranium (MTU), as well as an option to expand the inventory capacity, if authorized, to 97,000 MTU. The layout configuration also requires a degree of flexibility to accommodate potential changes in site conditions or program requirements. The objective of this analysis is to provide a conceptual design of the Subsurface Facility sufficient to support the development of the Subsurface Facility System Description Document (CRWMS M andO 2000e) and the ''Emplacement Drift System Description Document'' (CRWMS M andO 2000i). As well, this analysis provides input to the Site Recommendation Consideration Report. The scope of this analysis includes: (1) Evaluation of the existing facilities and their integration into the Subsurface Facility design. (2) Identification and incorporation of factors influencing Subsurface Facility design, such as geological constraints, thermal loading, constructibility, subsurface ventilation, drainage control, radiological considerations, and the Test and Evaluation Facilities. (3) Development of a layout showing an available area in the primary area sufficient to support both the waste inventories and individual layouts showing the emplacement area required for 70,000 MTU and, if authorized, 97,000 MTU

  5. Spatially and temporally controlled hydrogels for tissue engineering

    NARCIS (Netherlands)

    J., Leijten; Seo, Jungmok; Yue, Kan; Trujillo-de Santiago, Grissel; Tamayol, Ali; Ruiz-Esparza, Guillermo U.; Ryon Shin, Su; Sharifi, Roholah; Noshadi, Iman; Moises Alvarez, Mario; Shrike Zhang, Yu; Khademhosseini, Ali

    2017-01-01

    Recent years have seen tremendous advances in the field of hydrogel-based biomaterials. One of the most prominent revolutions in this field has been the integration of elements or techniques that enable spatial and temporal control over hydrogels’ properties and functions. Here, we critically review

  6. Spatial organization of adhesion: force-dependent regulation and function in tissue morphogenesis

    OpenAIRE

    Papusheva, Ekaterina; Heisenberg, Carl-Philipp

    2010-01-01

    The Heisenberg laboratory reviews the spatial organization of signalling complexes at cell–matrix and cell–cell contact sites and its impact on cell integrity, cellular polarity and tissue morphogenesis.

  7. Analysis on flexible manufacturing system layout using arena simulation software

    Science.gov (United States)

    Fadzly, M. K.; Saad, Mohd Sazli; Shayfull, Z.

    2017-09-01

    Flexible manufacturing system (FMS) was defined as highly automated group technology machine cell, consisting of a group of processing stations interconnected by an automated material handling and storage system, and controlled by an integrated computer system. FMS can produce parts or products are in the mid-volume, mid-variety production range. The layout system in FMS is an important criterion to design the FMS system to produce a part or product. This facility layout of an FMS involves the positioning of cells within given boundaries, so as to minimize the total projected travel time between cells. Defining the layout includes specifying the spatial coordinates of each cell, its orientation in either a horizontal or vertical position, and the location of its load or unloads point. There are many types of FMS layout such as In-line, loop ladder and robot centered cell layout. The research is concentrating on the design and optimization FMS layout. The final conclusion can be summarized that the objective to design and optimisation of FMS layout for this study is successful because the FMS In-line layout is the best layout based on effective time and cost using ARENA simulation software.

  8. Electrostatic Levitator Layout

    Science.gov (United States)

    1998-01-01

    Electrostatic Levitator (ESL) general layout with captions. The ESL uses static electricity to suspend an object (about 2-3 mm in diameter) inside a vacuum chamber while a laser heats the sample until it melts. This lets scientists record a wide range of physical properties without the sample contacting the container or any instruments, conditions that would alter the readings. The Electrostatic Levitator is one of several tools used in NASA's microgravity materials science program.

  9. Layout of LHCb

    CERN Multimedia

    CERN AC

    1998-01-01

    This diagram shows the layout for the LHCb detector, which will be part of the LHC project at CERN. The main purpose of this detector is to look for rare decays of a heavy quark known as 'bottom', a version of the down quark that is found in protons and neutrons. In particular, decays by a process known as 'CP violation' will be studied to investigate Nature's preference for matter over antimatter.

  10. Magnetoacoustic Imaging of Electrical Conductivity of Biological Tissues at a Spatial Resolution Better than 2 mm

    OpenAIRE

    Hu, Gang; He, Bin

    2011-01-01

    Magnetoacoustic tomography with magnetic induction (MAT-MI) is an emerging approach for noninvasively imaging electrical impedance properties of biological tissues. The MAT-MI imaging system measures ultrasound waves generated by the Lorentz force, having been induced by magnetic stimulation, which is related to the electrical conductivity distribution in tissue samples. MAT-MI promises to provide fine spatial resolution for biological tissue imaging as compared to ultrasound resolution. In t...

  11. Nanoscale tissue engineering: spatial control over cell-materials interactions

    Science.gov (United States)

    Wheeldon, Ian; Farhadi, Arash; Bick, Alexander G.; Jabbari, Esmaiel; Khademhosseini, Ali

    2011-01-01

    Cells interact with the surrounding environment by making tens to hundreds of thousands of nanoscale interactions with extracellular signals and features. The goal of nanoscale tissue engineering is to harness the interactions through nanoscale biomaterials engineering in order to study and direct cellular behaviors. Here, we review the nanoscale tissue engineering technologies for both two- and three-dimensional studies (2- and 3D), and provide a holistic overview of the field. Techniques that can control the average spacing and clustering of cell adhesion ligands are well established and have been highly successful in describing cell adhesion and migration in 2D. Extension of these engineering tools to 3D biomaterials has created many new hydrogel and nanofiber scaffolds technologies that are being used to design in vitro experiments with more physiologically relevant conditions. Researchers are beginning to study complex cell functions in 3D, however, there is a need for biomaterials systems that provide fine control over the nanoscale presentation of bioactive ligands in 3D. Additionally, there is a need for 2- and 3D techniques that can control the nanoscale presentation of multiple bioactive ligands and the temporal changes in cellular microenvironment. PMID:21451238

  12. Nanoscale tissue engineering: spatial control over cell-materials interactions

    International Nuclear Information System (INIS)

    Wheeldon, Ian; Farhadi, Arash; Bick, Alexander G; Khademhosseini, Ali; Jabbari, Esmaiel

    2011-01-01

    Cells interact with the surrounding environment by making tens to hundreds of thousands of nanoscale interactions with extracellular signals and features. The goal of nanoscale tissue engineering is to harness these interactions through nanoscale biomaterials engineering in order to study and direct cellular behavior. Here, we review two- and three-dimensional (2- and 3D) nanoscale tissue engineering technologies, and provide a holistic overview of the field. Techniques that can control the average spacing and clustering of cell adhesion ligands are well established and have been highly successful in describing cell adhesion and migration in 2D. Extension of these engineering tools to 3D biomaterials has created many new hydrogel and nanofiber scaffold technologies that are being used to design in vitro experiments with more physiologically relevant conditions. Researchers are beginning to study complex cell functions in 3D. However, there is a need for biomaterials systems that provide fine control over the nanoscale presentation of bioactive ligands in 3D. Additionally, there is a need for 2- and 3D techniques that can control the nanoscale presentation of multiple bioactive ligands and that can control the temporal changes in the cellular microenvironment. (topical review)

  13. Structure completion for facade layouts

    KAUST Repository

    Fan, Lubin

    2014-11-18

    (Figure Presented) We present a method to complete missing structures in facade layouts. Starting from an abstraction of the partially observed layout as a set of shapes, we can propose one or multiple possible completed layouts. Structure completion with large missing parts is an ill-posed problem. Therefore, we combine two sources of information to derive our solution: the observed shapes and a database of complete layouts. The problem is also very difficult, because shape positions and attributes have to be estimated jointly. Our proposed solution is to break the problem into two components: a statistical model to evaluate layouts and a planning algorithm to generate candidate layouts. This ensures that the completed result is consistent with the observation and the layouts in the database.

  14. Familiarisation: Restructuring Layouts with Visual Learning Models

    OpenAIRE

    Todi, Kashyap; Jokinen, Jussi; Luyten, Kris; Oulasvirta, Antti

    2018-01-01

    In domains where users are exposed to large variations in visuo-spatial features among designs, they often spend excess time searching for common elements (features) in familiar locations. This paper contributes computational approaches to restructuring layouts such that features on a new, unvisited interface can be found quicker. We explore four concepts of familiarisation, inspired by the human visual system (HVS), to automatically generate a familiar design for each user. Given a histor...

  15. Layout and composition for animation

    CERN Document Server

    Ghertner, Ed

    2012-01-01

    This essential, hands-on guide is filled with examples of what a composition should look like and example of poorly designed layouts. Spot potential problems before they cost time and money, and adapt creative solutions for your own projects with this invaluable resource for beginner and intermediate artists.  With Beauty and the Beast examples and Simpson character layouts, readers will learn how to develop character layout and background layout as well as strengthen composition  styles with a creative toolset of trick shot examples and inspirational case studies. A companion website will

  16. The EPR layout design

    International Nuclear Information System (INIS)

    Mast, U.; Le Carrer, P.Y.

    2001-01-01

    General: The European Pressurised Water Reactor (EPR) is a French - German development for the next generation of Pressurised Water Reactor. The new reactor design is based on the experiences of operation and design of nuclear power plants in both countries. The EPR fulfils enhanced safety standards, higher availability and a longer service life. Utilities aspects: For the Utilities one important requirement is the reduction of personnel exposure during maintenance and in-service inspection. The other significant requirement is of economic nature. The main points influencing costs, which have also impact on the layout, are: outage times, accessibility of the reactor building and the available maintenance and set down areas. The Utilities have also required to load the spent fuel assemblies into the shipping cask from the bottom of the fuel pool, because of the exclusion of the drop of the cask and in order to avoid contamination at the outer cask shell. Layout and safety aspects: All safety relevant Nuclear Island (NI) buildings are designed against design earthquake as well as explosion pressure wave. The protection against Airplane Crash (APC) is realised by civil and layout dispositions. The Reactor Building, the Safeguard Buildings division 2 and 3 and the Fuel Building are protected by concrete structures. The other safety relevant nuclear buildings are protected by geographical separation. Important safety requirements are the further reduction of the probability of severe accidents and the mitigation of such an accident on the plant area. For that, a spreading area for molten corium, a channel from the reactor pit to the spreading area and the In Containment Refuelling Water Storage Tank (IRWST) for flooding and initial cooling of the corium, were implemented in the design of the Reactor Building. Layout results: The following buildings are arranged on a common raft to protect them against design earthquake: Reactor Building (RB), Safeguard Buildings (SAB

  17. Underground layout tradeoff study

    International Nuclear Information System (INIS)

    1988-01-01

    This report presents the results of a technical and economic comparative study of four alternative underground layouts for a nuclear waste geologic repository in salt. The four alternatives considered in this study are (1) separate areas for spent fuel (SF) and commercial high-level waste (CHLW); (2) panel alternation, in which SF and CHLW are emplaced in adjacent panels of rooms; (3) room alternation, in which SF and CHLW are emplaced in adjacent rooms within each panel; and (4) intimate mixture, in which SF and CHLW are emplaced in random order within each storage room. The study concludes that (1) cost is not an important factor; (2) the separate-areas and intimate-mixture alternatives appear, technically, to be more desirable than the other alternatives; and (3) the selection between the separate-areas and intimate mixture alternatives depends upon future resolution of site-specific and reprocessing questions. 5 refs., 6 figs., 12 tabs

  18. Spatially Different Tissue-Scale Diffusivity Shapes ANGUSTIFOLIA3 Gradient in Growing Leaves.

    Science.gov (United States)

    Kawade, Kensuke; Tanimoto, Hirokazu; Horiguchi, Gorou; Tsukaya, Hirokazu

    2017-09-05

    The spatial gradient of signaling molecules is pivotal for establishing developmental patterns of multicellular organisms. It has long been proposed that these gradients could arise from the pure diffusion process of signaling molecules between cells, but whether this simplest mechanism establishes the formation of the tissue-scale gradient remains unclear. Plasmodesmata are unique channel structures in plants that connect neighboring cells for molecular transport. In this study, we measured cellular- and tissue-scale kinetics of molecular transport through plasmodesmata in Arabidopsis thaliana developing leaf primordia by fluorescence recovery assays. These trans-scale measurements revealed biophysical properties of diffusive molecular transport through plasmodesmata and revealed that the tissue-scale diffusivity, but not the cellular-scale diffusivity, is spatially different along the leaf proximal-to-distal axis. We found that the gradient in cell size along the developmental axis underlies this spatially different tissue-scale diffusivity. We then asked how this diffusion-based framework functions in establishing a signaling gradient of endogenous molecules. ANGUSTIFOLIA3 (AN3) is a transcriptional co-activator, and as we have shown here, it forms a long-range signaling gradient along the leaf proximal-to-distal axis to determine a cell-proliferation domain. By genetically engineering AN3 mobility, we assessed each contribution of cell-to-cell movement and tissue growth to the distribution of the AN3 gradient. We constructed a diffusion-based theoretical model using these quantitative data to analyze the AN3 gradient formation and demonstrated that it could be achieved solely by the diffusive molecular transport in a growing tissue. Our results indicate that the spatially different tissue-scale diffusivity is a core mechanism for AN3 gradient formation. This provides evidence that the pure diffusion process establishes the formation of the long-range signaling

  19. Spatial dose and microdose distribution in tissues. Ionization, nuclear reactions, multiple scattering simulation of beam transport

    International Nuclear Information System (INIS)

    Jacquot, C.

    1976-01-01

    Computer simulation and nuclear emulsion and gelatin techniques enabled to give the total elastic and inelastic cross sections and to forecast the spatial microdose distributions in cells, nuclei and molecules. For this purpose, the transport of a beam into tissues having a given composition is calculated, the nuclear reactions are generated and the energy depositions in standard planes perpendicular to the beam are recorded

  20. Estimating perception of scene layout properties from global image features.

    Science.gov (United States)

    Ross, Michael G; Oliva, Aude

    2010-01-08

    The relationship between image features and scene structure is central to the study of human visual perception and computer vision, but many of the specifics of real-world layout perception remain unknown. We do not know which image features are relevant to perceiving layout properties, or whether those features provide the same information for every type of image. Furthermore, we do not know the spatial resolutions required for perceiving different properties. This paper describes an experiment and a computational model that provides new insights on these issues. Humans perceive the global spatial layout properties such as dominant depth, openness, and perspective, from a single image. This work describes an algorithm that reliably predicts human layout judgments. This model's predictions are general, not specific to the observers it trained on. Analysis reveals that the optimal spatial resolutions for determining layout vary with the content of the space and the property being estimated. Openness is best estimated at high resolution, depth is best estimated at medium resolution, and perspective is best estimated at low resolution. Given the reliability and simplicity of estimating the global layout of real-world environments, this model could help resolve perceptual ambiguities encountered by more detailed scene reconstruction schemas.

  1. Genomic organization and the tissue distribution of alternatively spliced isoforms of the mouse Spatial gene

    Directory of Open Access Journals (Sweden)

    Mattei Marie-Geneviève

    2004-07-01

    Full Text Available Abstract Background The stromal component of the thymic microenvironment is critical for T lymphocyte generation. Thymocyte differentiation involves a cascade of coordinated stromal genes controlling thymocyte survival, lineage commitment and selection. The "Stromal Protein Associated with Thymii And Lymph-node" (Spatial gene encodes a putative transcription factor which may be involved in T-cell development. In the testis, the Spatial gene is also expressed by round spermatids during spermatogenesis. Results The Spatial gene maps to the B3-B4 region of murine chromosome 10 corresponding to the human syntenic region 10q22.1. The mouse Spatial genomic DNA is organised into 10 exons and is alternatively spliced to generate two short isoforms (Spatial-α and -γ and two other long isoforms (Spatial-δ and -ε comprising 5 additional exons on the 3' site. Here, we report the cloning of a new short isoform, Spatial-β, which differs from other isoforms by an additional alternative exon of 69 bases. This new exon encodes an interesting proline-rich signature that could confer to the 34 kDa Spatial-β protein a particular function. By quantitative TaqMan RT-PCR, we have shown that the short isoforms are highly expressed in the thymus while the long isoforms are highly expressed in the testis. We further examined the inter-species conservation of Spatial between several mammals and identified that the protein which is rich in proline and positive amino acids, is highly conserved. Conclusions The Spatial gene generates at least five alternative spliced variants: three short isoforms (Spatial-α, -β and -γ highly expressed in the thymus and two long isoforms (Spatial-δ and -ε highly expressed in the testis. These alternative spliced variants could have a tissue specific function.

  2. A minimal spatial cell lineage model of epithelium: tissue stratification and multi-stability

    Science.gov (United States)

    Yeh, Wei-Ting; Chen, Hsuan-Yi

    2018-05-01

    A minimal model which includes spatial and cell lineage dynamics for stratified epithelia is presented. The dependence of tissue steady state on cell differentiation models, cell proliferation rate, cell differentiation rate, and other parameters are studied numerically and analytically. Our minimal model shows some important features. First, we find that morphogen or mechanical stress mediated interaction is necessary to maintain a healthy stratified epithelium. Furthermore, comparing with tissues in which cell differentiation can take place only during cell division, tissues in which cell division and cell differentiation are decoupled can achieve relatively higher degree of stratification. Finally, our model also shows that in the presence of short-range interactions, it is possible for a tissue to have multiple steady states. The relation between our results and tissue morphogenesis or lesion is discussed.

  3. Spatial cluster analysis of nanoscopically mapped serotonin receptors for classification of fixed brain tissue

    Science.gov (United States)

    Sams, Michael; Silye, Rene; Göhring, Janett; Muresan, Leila; Schilcher, Kurt; Jacak, Jaroslaw

    2014-01-01

    We present a cluster spatial analysis method using nanoscopic dSTORM images to determine changes in protein cluster distributions within brain tissue. Such methods are suitable to investigate human brain tissue and will help to achieve a deeper understanding of brain disease along with aiding drug development. Human brain tissue samples are usually treated postmortem via standard fixation protocols, which are established in clinical laboratories. Therefore, our localization microscopy-based method was adapted to characterize protein density and protein cluster localization in samples fixed using different protocols followed by common fluorescent immunohistochemistry techniques. The localization microscopy allows nanoscopic mapping of serotonin 5-HT1A receptor groups within a two-dimensional image of a brain tissue slice. These nanoscopically mapped proteins can be confined to clusters by applying the proposed statistical spatial analysis. Selected features of such clusters were subsequently used to characterize and classify the tissue. Samples were obtained from different types of patients, fixed with different preparation methods, and finally stored in a human tissue bank. To verify the proposed method, samples of a cryopreserved healthy brain have been compared with epitope-retrieved and paraffin-fixed tissues. Furthermore, samples of healthy brain tissues were compared with data obtained from patients suffering from mental illnesses (e.g., major depressive disorder). Our work demonstrates the applicability of localization microscopy and image analysis methods for comparison and classification of human brain tissues at a nanoscopic level. Furthermore, the presented workflow marks a unique technological advance in the characterization of protein distributions in brain tissue sections.

  4. CT imaging during microwave ablation: Analysis of spatial and temporal tissue contraction

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Dong; Brace, Christopher L., E-mail: clbrace@wisc.edu [Departments of Radiology and Biomedical Engineering, University of Wisconsin, Madison, Wisconsin 53705 (United States)

    2014-11-01

    Purpose: To analyze the spatial distribution and temporal development of liver tissue contraction during high-temperature ablation by using intraprocedural computed tomography (CT) imaging. Methods: A total of 46 aluminum fiducial markers were positioned in a 60 × 45 mm grid, in a single plane, around a microwave ablation antenna in each of six ex vivo bovine liver samples. Ablations were performed for 10 min at 100 W. CT data of the liver sample were acquired every 30 s during ablation. Fiducial motion between acquisitions was tracked in postprocessing and used to calculate measures of tissue contraction and contraction rates. The spatial distribution and temporal evolution of contraction were analyzed. Results: Fiducial displacement indicated that the zone measured postablation was 8.2 ± 1.8 mm (∼20%) smaller in the radial direction and 7.1 ± 1.0 mm (∼10%) shorter in the longitudinal direction than the preablation tissue dimension. Therefore, the total ablation volume was reduced from its preablation value by approximately 45%. Very little longitudinal contraction was noted in the distal portion of the ablation zone. Central tissues contracted more than 60%, which was near an estimated limit of ∼70% based on initial water content. More peripheral tissues contracted only 15% in any direction. Contraction rates peaked during the first 60 s of heating with a roughly exponential decay over time. Conclusions: Ablation zones measured posttreatment are significantly smaller than the pretreatment tissue dimensions. Tissue contraction is spatially dependent, with the greatest effect occurring in the central ablation zone. Contraction rate peaks early and decays over time.

  5. How the global layout of the mask influences masking strength.

    Science.gov (United States)

    Ghose, Tandra; Hermens, Frouke; Herzog, Michael H

    2012-12-10

    In visual backward masking, the perception of a target is influenced by a trailing mask. Masking is usually explained by local interactions between the target and the mask representations. However, recently it has been shown that the global spatial layout of the mask rather than its local structure determines masking strength (Hermens & Herzog, 2007). Here, we varied the mask layout by spatial, luminance, and temporal cues. We presented a vernier target followed by a mask with 25 elements. Performance deteriorated when the length of the two mask elements neighboring the target vernier was doubled. However, when the length of every second mask element was doubled, performance improved. When the luminance of the neighboring elements was doubled, performance also deteriorated but no improvement in performance was observed when every second element had a double luminance. For temporal manipulations, a complex nonmonotonic masking function was observed. Hence, changes in the mask layout by spatial, luminance, and temporal cues lead to highly different results.

  6. Quantitative comparison between two geometrical layouts for diffraction enhanced imaging

    International Nuclear Information System (INIS)

    Huang Wanxia; Yuan Qingxi; Zhu Peiping; Wang Junyue; Shu Hang; Chen Bo; Hu Tiandou; Wu Ziyu

    2007-01-01

    Diffraction enhanced imaging (DEI) with two crystals has been performed at the 4W1A beamline at Beijing Synchrotron Radiation Facility (BSRF). Two different crystal geometrical layouts were used to collect images, in the first layout the rotation axis of the crystal has been set perpendicular to the orbital plane while in the second the axis is parallel to the orbital plane. Performance comparison between the two layouts is discussed in terms of thermal expansion of the crystal induced by the heat load, imaging homogeneity, spatial resolution and angular resolution. From both experimental and theoretical data we show that the best images may be obtained with the optical layout in which the rotation axis of the crystals is perpendicular to the orbital plane

  7. Quantitative comparison between two geometrical layouts for diffraction enhanced imaging

    Energy Technology Data Exchange (ETDEWEB)

    Huang Wanxia; Yuan Qingxi [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, Beijing (China); Zhu Peiping [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, Beijing (China)], E-mail: zhupp@ihep.ac.cn; Wang Junyue; Shu Hang [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, Beijing (China); Chen Bo [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, Beijing (China); Department of Physics, University of Science and Technology of China, Hefei (China); Hu Tiandou [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, Beijing (China); Wu Ziyu [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, CAS, Beijing (China)], E-mail: wuzy@ihep.ac.cn

    2007-07-15

    Diffraction enhanced imaging (DEI) with two crystals has been performed at the 4W1A beamline at Beijing Synchrotron Radiation Facility (BSRF). Two different crystal geometrical layouts were used to collect images, in the first layout the rotation axis of the crystal has been set perpendicular to the orbital plane while in the second the axis is parallel to the orbital plane. Performance comparison between the two layouts is discussed in terms of thermal expansion of the crystal induced by the heat load, imaging homogeneity, spatial resolution and angular resolution. From both experimental and theoretical data we show that the best images may be obtained with the optical layout in which the rotation axis of the crystals is perpendicular to the orbital plane.

  8. Computing layouts with deformable templates

    KAUST Repository

    Peng, Chi-Han

    2014-07-22

    In this paper, we tackle the problem of tiling a domain with a set of deformable templates. A valid solution to this problem completely covers the domain with templates such that the templates do not overlap. We generalize existing specialized solutions and formulate a general layout problem by modeling important constraints and admissible template deformations. Our main idea is to break the layout algorithm into two steps: a discrete step to lay out the approximate template positions and a continuous step to refine the template shapes. Our approach is suitable for a large class of applications, including floorplans, urban layouts, and arts and design. Copyright © ACM.

  9. Computing layouts with deformable templates

    KAUST Repository

    Peng, Chi-Han; Yang, Yongliang; Wonka, Peter

    2014-01-01

    In this paper, we tackle the problem of tiling a domain with a set of deformable templates. A valid solution to this problem completely covers the domain with templates such that the templates do not overlap. We generalize existing specialized solutions and formulate a general layout problem by modeling important constraints and admissible template deformations. Our main idea is to break the layout algorithm into two steps: a discrete step to lay out the approximate template positions and a continuous step to refine the template shapes. Our approach is suitable for a large class of applications, including floorplans, urban layouts, and arts and design. Copyright © ACM.

  10. Practical Aspects of CMOS Layout

    DEFF Research Database (Denmark)

    Stassen, Flemming

    1996-01-01

    The topics covered in these notes are the practical aspects and limitations of layout, when random process variations result in electrical parameters, which are not constant but rather statistically distributed.The focus is on design methods for reducing or eliminating the effects. The notes cover...... three aspects:1) to introduce layout structures robust to process variations2) to present simplistic models for analog building blocks with the aim of analysing consequences of parameter variations3) to present the basic noise considerations which guide the layout of supply structures etc....

  11. Probabilistic Graph Layout for Uncertain Network Visualization.

    Science.gov (United States)

    Schulz, Christoph; Nocaj, Arlind; Goertler, Jochen; Deussen, Oliver; Brandes, Ulrik; Weiskopf, Daniel

    2017-01-01

    We present a novel uncertain network visualization technique based on node-link diagrams. Nodes expand spatially in our probabilistic graph layout, depending on the underlying probability distributions of edges. The visualization is created by computing a two-dimensional graph embedding that combines samples from the probabilistic graph. A Monte Carlo process is used to decompose a probabilistic graph into its possible instances and to continue with our graph layout technique. Splatting and edge bundling are used to visualize point clouds and network topology. The results provide insights into probability distributions for the entire network-not only for individual nodes and edges. We validate our approach using three data sets that represent a wide range of network types: synthetic data, protein-protein interactions from the STRING database, and travel times extracted from Google Maps. Our approach reveals general limitations of the force-directed layout and allows the user to recognize that some nodes of the graph are at a specific position just by chance.

  12. Structure completion for facade layouts

    KAUST Repository

    Fan, Lubin; Musialski, Przemyslaw; Liu, Ligang; Wonka, Peter

    2014-01-01

    completion with large missing parts is an ill-posed problem. Therefore, we combine two sources of information to derive our solution: the observed shapes and a database of complete layouts. The problem is also very difficult, because shape positions

  13. Spatial organization and correlation properties quantify structural changes on mesoscale of parenchymatous plant tissue

    Energy Technology Data Exchange (ETDEWEB)

    Valous, N. A.; Delgado, A.; Sun, D.-W., E-mail: dawen.sun@ucd.ie [School of Biosystems Engineering, University College Dublin, National University of Ireland, Belfield, Dublin 4, Dublin (Ireland); Drakakis, K. [Complex and Adaptive Systems Laboratory, University College Dublin, National University of Ireland, Belfield, Dublin 4, Dublin (Ireland)

    2014-02-14

    The study of plant tissue parenchyma's intercellular air spaces contributes to the understanding of anatomy and physiology. This is challenging due to difficulty in making direct measurements of the pore space and the complex mosaic of parenchymatous tissue. The architectural complexity of pore space has shown that single geometrical measurements are not sufficient for characterization. The inhomogeneity of distribution depends not only on the percentage content of phase, but also on how the phase fills the space. The lacunarity morphometric, as multiscale measure, provides information about the distribution of gaps that correspond to degree of spatial organization in parenchyma. Additionally, modern theories have suggested strategies, where the focus has shifted from the study of averages and histograms to the study of patterns in data fluctuations. Detrended fluctuation analysis provides information on the correlation properties of the parenchyma at different spatial scales. The aim is to quantify (with the aid of the aforementioned metrics), the mesostructural changes—that occur from one cycle of freezing and thawing—in the void phase of pome fruit parenchymatous tissue, acquired with X-ray microcomputed tomography. Complex systems methods provide numerical indices and detailed insights regarding the freezing-induced modifications upon the arrangement of cells and voids. These structural changes have the potential to lead to physiological disorders. The work can further stimulate interest for the analysis of internal plant tissue structures coupled with other physico-chemical processes or phenomena.

  14. Spatial organization and correlation properties quantify structural changes on mesoscale of parenchymatous plant tissue

    International Nuclear Information System (INIS)

    Valous, N. A.; Delgado, A.; Sun, D.-W.; Drakakis, K.

    2014-01-01

    The study of plant tissue parenchyma's intercellular air spaces contributes to the understanding of anatomy and physiology. This is challenging due to difficulty in making direct measurements of the pore space and the complex mosaic of parenchymatous tissue. The architectural complexity of pore space has shown that single geometrical measurements are not sufficient for characterization. The inhomogeneity of distribution depends not only on the percentage content of phase, but also on how the phase fills the space. The lacunarity morphometric, as multiscale measure, provides information about the distribution of gaps that correspond to degree of spatial organization in parenchyma. Additionally, modern theories have suggested strategies, where the focus has shifted from the study of averages and histograms to the study of patterns in data fluctuations. Detrended fluctuation analysis provides information on the correlation properties of the parenchyma at different spatial scales. The aim is to quantify (with the aid of the aforementioned metrics), the mesostructural changes—that occur from one cycle of freezing and thawing—in the void phase of pome fruit parenchymatous tissue, acquired with X-ray microcomputed tomography. Complex systems methods provide numerical indices and detailed insights regarding the freezing-induced modifications upon the arrangement of cells and voids. These structural changes have the potential to lead to physiological disorders. The work can further stimulate interest for the analysis of internal plant tissue structures coupled with other physico-chemical processes or phenomena

  15. High-spatial-resolution mapping of the oxygen concentration in cortical tissue (Conference Presentation)

    Science.gov (United States)

    Jaswal, Rajeshwer S.; Yaseen, Mohammad A.; Fu, Buyin; Boas, David A.; Sakadžic, Sava

    2016-03-01

    Due to a lack of imaging tools for high-resolution imaging of cortical tissue oxygenation, the detailed maps of the oxygen partial pressure (PO2) around arterioles, venules, and capillaries remain largely unknown. Therefore, we have limited knowledge about the mechanisms that secure sufficient oxygen delivery in microvascular domains during brain activation, and provide some metabolic reserve capacity in diseases that affect either microvascular networks or the regulation of cerebral blood flow (CBF). To address this challenge, we applied a Two-Photon PO2 Microscopy to map PO2 at different depths in mice cortices. Measurements were performed through the cranial window in the anesthetized healthy mice as well as in the mouse models of microvascular dysfunctions. In addition, microvascular morphology was recorded by the two-photon microscopy at the end of each experiment and subsequently segmented. Co-registration of the PO2 measurements and exact microvascular morphology enabled quantification of the tissue PO2 dependence on distance from the arterioles, capillaries, and venules at various depths. Our measurements reveal significant spatial heterogeneity of the cortical tissue PO2 distribution that is dominated by the high oxygenation in periarteriolar spaces. In cases of impaired oxygen delivery due to microvascular dysfunction, significant reduction in tissue oxygenation away from the arterioles was observed. These tissue domains may be the initial sites of cortical injury that can further exacerbate the progression of the disease.

  16. Accelerating ROP detector layout optimization

    International Nuclear Information System (INIS)

    Kastanya, D.; Fodor, B.

    2012-01-01

    The ADORE (Alternating Detector layout Optimization for REgional overpower protection system) algorithm for performing the optimization of regional overpower protection (ROP) system for CANDU® reactors have been recently developed. The simulated annealing (SA) stochastic optimization technique is utilized to come up with a quasi optimized detector layout for the ROP systems. Within each simulated annealing history, the objective function is calculated as a function of the trip set point (TSP) corresponding to the detector layout for that particular history. The evaluation of the TSP is done probabilistically using the ROVER-F code. Since during each optimization execution thousands of candidate detector layouts are evaluated, the overall optimization process is time consuming. Since for each ROVER-F evaluation the number of fuelling ripples controls the execution time, reducing the number of fuelling ripples used during the calculation of TSP will reduce the overall optimization execution time. This approach has been investigated and the results are presented in this paper. The challenge is to construct a set of representative fuelling ripples which will significantly speedup the optimization process while guaranteeing that the resulting detector layout has similar quality to the ones produced when the complete set of fuelling ripples is employed. Results presented in this paper indicate that a speedup of up to around 40 times is attainable when this approach is utilized. (author)

  17. Cache-Oblivious Mesh Layouts

    International Nuclear Information System (INIS)

    Yoon, S; Lindstrom, P; Pascucci, V; Manocha, D

    2005-01-01

    We present a novel method for computing cache-oblivious layouts of large meshes that improve the performance of interactive visualization and geometric processing algorithms. Given that the mesh is accessed in a reasonably coherent manner, we assume no particular data access patterns or cache parameters of the memory hierarchy involved in the computation. Furthermore, our formulation extends directly to computing layouts of multi-resolution and bounding volume hierarchies of large meshes. We develop a simple and practical cache-oblivious metric for estimating cache misses. Computing a coherent mesh layout is reduced to a combinatorial optimization problem. We designed and implemented an out-of-core multilevel minimization algorithm and tested its performance on unstructured meshes composed of tens to hundreds of millions of triangles. Our layouts can significantly reduce the number of cache misses. We have observed 2-20 times speedups in view-dependent rendering, collision detection, and isocontour extraction without any modification of the algorithms or runtime applications

  18. Simulated annealing and circuit layout

    NARCIS (Netherlands)

    Aarts, E.H.L.; Laarhoven, van P.J.M.

    1991-01-01

    We discuss the problem of approximately sotvlng circuit layout problems by simulated annealing. For this we first summarize the theoretical concepts of the simulated annealing algorithm using Ihe theory of homogeneous and inhomogeneous Markov chains. Next we briefly review general aspects of the

  19. Small Business Location and Layout.

    Science.gov (United States)

    Small Business Administration, Washington, DC.

    As an approach to teaching small-business location and layout, this publication contains material for teaching one session of a basic course. The sections of the publication are as follows: (1) The Lesson Plan--an outline of the material covered, which may be used as a teaching guide, presented in two columns: an outline of the presentation, and a…

  20. Quantitative Susceptibility Mapping of Human Brain Reflects Spatial Variation in Tissue Composition

    Science.gov (United States)

    Li, Wei; Wu, Bing; Liu, Chunlei

    2011-01-01

    Image phase from gradient echo MRI provides a unique contrast that reflects brain tissue composition variations, such as iron and myelin distribution. Phase imaging is emerging as a powerful tool for the investigation of functional brain anatomy and disease diagnosis. However, the quantitative value of phase is compromised by its nonlocal and orientation dependent properties. There is an increasing need for reliable quantification of magnetic susceptibility, the intrinsic property of tissue. In this study, we developed a novel and accurate susceptibility mapping method that is also phase-wrap insensitive. The proposed susceptibility mapping method utilized two complementary equations: (1) the Fourier relationship of phase and magnetic susceptibility; and (2) the first-order partial derivative of the first equation in the spatial frequency domain. In numerical simulation, this method reconstructed the susceptibility map almost free of streaking artifact. Further, the iterative implementation of this method allowed for high quality reconstruction of susceptibility maps of human brain in vivo. The reconstructed susceptibility map provided excellent contrast of iron-rich deep nuclei and white matter bundles from surrounding tissues. Further, it also revealed anisotropic magnetic susceptibility in brain white matter. Hence, the proposed susceptibility mapping method may provide a powerful tool for the study of brain physiology and pathophysiology. Further elucidation of anisotropic magnetic susceptibility in vivo may allow us to gain more insight into the white matter microarchitectures. PMID:21224002

  1. Voxel-based measurement sensitivity of spatially resolved near-infrared spectroscopy in layered tissues.

    Science.gov (United States)

    Niwayama, Masatsugu

    2018-03-01

    We quantitatively investigated the measurement sensitivity of spatially resolved spectroscopy (SRS) across six tissue models: cerebral tissue, a small animal brain, the forehead of a fetus, an adult brain, forearm muscle, and thigh muscle. The optical path length in the voxel of the model was analyzed using Monte Carlo simulations. It was found that the measurement sensitivity can be represented as the product of the change in the absorption coefficient and the difference in optical path length in two states with different source-detector distances. The results clarified the sensitivity ratio between the surface layer and the deep layer at each source-detector distance for each model and identified changes in the deep measurement area when one of the detectors was close to the light source. A comparison was made with the results from continuous-wave spectroscopy. The study also identified measurement challenges that arise when the surface layer is inhomogeneous. Findings on the measurement sensitivity of SRS at each voxel and in each layer can support the correct interpretation of measured values when near-infrared oximetry or functional near-infrared spectroscopy is used to investigate different tissue structures. (2018) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE).

  2. Generating and exploring good building layouts

    KAUST Repository

    Bao, Fan; Yan, Dongming; Mitra, Niloy J.; Wonka, Peter

    2013-01-01

    Good building layouts are required to conform to regulatory guidelines, while meeting certain quality measures. While different methods can sample the space of such good layouts, there exists little support for a user to understand

  3. Patch layout generation by detecting feature networks

    KAUST Repository

    Cao, Yuanhao; Yan, Dongming; Wonka, Peter

    2015-01-01

    The patch layout of 3D surfaces reveals the high-level geometric and topological structures. In this paper, we study the patch layout computation by detecting and enclosing feature loops on surfaces. We present a hybrid framework which combines

  4. HOLA: Human-like Orthogonal Network Layout.

    Science.gov (United States)

    Kieffer, Steve; Dwyer, Tim; Marriott, Kim; Wybrow, Michael

    2016-01-01

    Over the last 50 years a wide variety of automatic network layout algorithms have been developed. Some are fast heuristic techniques suitable for networks with hundreds of thousands of nodes while others are multi-stage frameworks for higher-quality layout of smaller networks. However, despite decades of research currently no algorithm produces layout of comparable quality to that of a human. We give a new "human-centred" methodology for automatic network layout algorithm design that is intended to overcome this deficiency. User studies are first used to identify the aesthetic criteria algorithms should encode, then an algorithm is developed that is informed by these criteria and finally, a follow-up study evaluates the algorithm output. We have used this new methodology to develop an automatic orthogonal network layout method, HOLA, that achieves measurably better (by user study) layout than the best available orthogonal layout algorithm and which produces layouts of comparable quality to those produced by hand.

  5. COMPUTER AIDED SELECTION OF PLANT LAYOUT

    African Journals Online (AJOL)

    Special focus is directed at improving the preparation of the input data to enhance computer assistance to plant layout. ... INTRODUCTION. Plant layout problems have ... 1960's with the development by industrial engineers and operational ...

  6. Procedural modeling of urban layout: population, land use, and road network

    OpenAIRE

    Lyu, X.; Han, Q.; de Vries, B.

    2017-01-01

    This paper introduces an urban simulation system generating urban layouts with population, road network and land use layers. The desired urban spatial structure is obtained by generating a population map based on population density models. The road network is generated at two spatial levels corresponding to the road hierarchy. The land use allocation is based on the What If? allocation model. The expected results are urban layouts suitable for academic scenario analysis.

  7. Computational Design of Urban Layouts

    KAUST Repository

    Wonka, Peter

    2015-10-07

    A fundamental challenge in computational design is to compute layouts by arranging a set of shapes. In this talk I will present recent urban modeling projects with applications in computer graphics, urban planning, and architecture. The talk will look at different scales of urban modeling (streets, floorplans, parcels). A common challenge in all these modeling problems are functional and aesthetic constraints that should be respected. The talk also highlights interesting links to geometry processing problems, such as field design and quad meshing.

  8. ITER fuel cycle systems layout

    International Nuclear Information System (INIS)

    Kveton, O.K.

    1990-10-01

    The ITER fuel cycle building (FCB) will contain the following systems: fuel purification - permeator based; fuel purification - molecular sieves; impurity treatment; waste water storage and treatment; isotope separation; waste water tritium extraction; tritium extraction from solid breeder; tritium extraction from test modules; tritium storage, shipping and receiving; tritium laboratory; atmosphere detritiation systems; fuel cycle control centre; tritiated equipment maintenance space; control maintenance space; health physics laboratory; access, access control and facilities. The layout of the FCB and the requirements for these systems are described. (10 figs.)

  9. Spatial distribution of theobromine--a low MW drug--in tissues via matrix-free NALDI-MS imaging.

    Science.gov (United States)

    Tata, Alessandra; Montemurro, Chiara; Porcari, Andreia M; Silva, Kamila C; Lopes de Faria, José B; Eberlin, Marcos N

    2014-09-01

    The ability of nano-assisted laser desorption-ionization mass spectrometry imaging (NALDI-IMS) to provide selective chemical monitoring with appropriate spatial distribution of a low molecular drug in a biological tissue was investigated. NALDI-IMS is a matrix-free laser desorption ionization (LDI) protocol based on imprinting of tissue constituents on a nanostructured surface. Using the accumulation of theobromine in rat kidney as a model, NALDI-IMS was found to provide well-resolved images of the special distribution of this low molecular weight (MW) drug in tissue. Copyright © 2014 John Wiley & Sons, Ltd.

  10. Towards personalized computational oncology: from spatial models of tumour spheroids, to organoids, to tissues.

    Science.gov (United States)

    Karolak, Aleksandra; Markov, Dmitry A; McCawley, Lisa J; Rejniak, Katarzyna A

    2018-01-01

    A main goal of mathematical and computational oncology is to develop quantitative tools to determine the most effective therapies for each individual patient. This involves predicting the right drug to be administered at the right time and at the right dose. Such an approach is known as precision medicine. Mathematical modelling can play an invaluable role in the development of such therapeutic strategies, since it allows for relatively fast, efficient and inexpensive simulations of a large number of treatment schedules in order to find the most effective. This review is a survey of mathematical models that explicitly take into account the spatial architecture of three-dimensional tumours and address tumour development, progression and response to treatments. In particular, we discuss models of epithelial acini, multicellular spheroids, normal and tumour spheroids and organoids, and multi-component tissues. Our intent is to showcase how these in silico models can be applied to patient-specific data to assess which therapeutic strategies will be the most efficient. We also present the concept of virtual clinical trials that integrate standard-of-care patient data, medical imaging, organ-on-chip experiments and computational models to determine personalized medical treatment strategies. © 2018 The Author(s).

  11. Generating and exploring good building layouts

    KAUST Repository

    Bao, Fan

    2013-07-16

    Good building layouts are required to conform to regulatory guidelines, while meeting certain quality measures. While different methods can sample the space of such good layouts, there exists little support for a user to understand and systematically explore the samples. Starting from a discrete set of good layouts, we analytically characterize the local shape space of good layouts around each initial layout, compactly encode these spaces, and link them to support transitions across the different local spaces. We represent such transitions in the form of a portal graph. The user can then use the portal graph, along with the family of local shape spaces, to globally and locally explore the space of good building layouts. We use our framework on a variety of different test scenarios to showcase an intuitive design, navigation, and exploration interface. Copyright © ACM. Copyright © ACM 2013.

  12. 3D MRI Modeling of Thin and Spatially Complex Soft Tissue Structures without Shrinkage: Lamprey Myosepta as an Example.

    Science.gov (United States)

    Wood, Bradley M; Jia, Guang; Carmichael, Owen; McKlveen, Kevin; Homberger, Dominique G

    2018-05-12

    3D imaging techniques enable the non-destructive analysis and modeling of complex structures. Among these, MRI exhibits good soft tissue contrast, but is currently less commonly used for non-clinical research than x-ray CT, even though the latter requires contrast-staining that shrinks and distorts soft tissues. When the objective is the creation of a realistic and complete 3D model of soft tissue structures, MRI data are more demanding to acquire and visualize and require extensive post-processing because they comprise non-cubic voxels with dimensions that represent a trade-off between tissue contrast and image resolution. Therefore, thin soft tissue structures with complex spatial configurations are not always visible in a single MRI dataset, so that standard segmentation techniques are not sufficient for their complete visualization. By using the example of the thin and spatially complex connective tissue myosepta in lampreys, we developed a workflow protocol for the selection of the appropriate parameters for the acquisition of MRI data and for the visualization and 3D modeling of soft tissue structures. This protocol includes a novel recursive segmentation technique for supplementing missing data in one dataset with data from another dataset to produce realistic and complete 3D models. Such 3D models are needed for the modeling of dynamic processes, such as the biomechanics of fish locomotion. However, our methodology is applicable to the visualization of any thin soft tissue structures with complex spatial configurations, such as fasciae, aponeuroses, and small blood vessels and nerves, for clinical research and the further exploration of tensegrity. This article is protected by copyright. All rights reserved. © 2018 Wiley Periodicals, Inc.

  13. Tissue-specific features of the X chromosome and nucleolus spatial dynamics in a malaria mosquito, Anopheles atroparvus.

    Science.gov (United States)

    Bondarenko, Semen M; Artemov, Gleb N; Sharakhov, Igor V; Stegniy, Vladimir N

    2017-01-01

    Spatial organization of chromosome territories is important for maintenance of genomic stability and regulation of gene expression. Recent studies have shown tissue-specific features of chromosome attachments to the nuclear envelope in various organisms including malaria mosquitoes. However, other spatial characteristics of nucleus organization, like volume and shape of chromosome territories, have not been studied in Anopheles. We conducted a thorough analysis of tissue-specific features of the X chromosome and nucleolus volume and shape in follicular epithelium and nurse cells of the Anopheles atroparvus ovaries using a modern open-source software. DNA of the polytene X chromosome from ovarian nurse cells was obtained by microdissection and was used as a template for amplification with degenerate oligo primers. A fluorescently labeled X chromosome painting probe was hybridized with formaldehyde-fixed ovaries of mosquitoes using a 3D-FISH method. The nucleolus was stained by immunostaining with an anti-fibrillarin antibody. The analysis was conducted with TANGO-a software for a chromosome spatial organization analysis. We show that the volume and position of the X chromosome have tissue-specific characteristics. Unlike nurse cell nuclei, the growth of follicular epithelium nuclei is not accompanied with the proportional growth of the X chromosome. However, the shape of the X chromosome does not differ between the tissues. The dynamics of the X chromosome attachment regions location is tissue-specific and it is correlated with the process of nucleus growth in follicular epithelium and nurse cells.

  14. Interactive Graph Layout of a Million Nodes

    OpenAIRE

    Peng Mi; Maoyuan Sun; Moeti Masiane; Yong Cao; Chris North

    2016-01-01

    Sensemaking of large graphs, specifically those with millions of nodes, is a crucial task in many fields. Automatic graph layout algorithms, augmented with real-time human-in-the-loop interaction, can potentially support sensemaking of large graphs. However, designing interactive algorithms to achieve this is challenging. In this paper, we tackle the scalability problem of interactive layout of large graphs, and contribute a new GPU-based force-directed layout algorithm that exploits graph to...

  15. Patch layout generation by detecting feature networks

    KAUST Repository

    Cao, Yuanhao

    2015-02-01

    The patch layout of 3D surfaces reveals the high-level geometric and topological structures. In this paper, we study the patch layout computation by detecting and enclosing feature loops on surfaces. We present a hybrid framework which combines several key ingredients, including feature detection, feature filtering, feature curve extension, patch subdivision and boundary smoothing. Our framework is able to compute patch layouts through concave features as previous approaches, but also able to generate nice layouts through smoothing regions. We demonstrate the effectiveness of our framework by comparing with the state-of-the-art methods.

  16. Linking microscopic spatial patterns of tissue destruction in emphysema to macroscopic decline in stiffness using a 3D computational model.

    Directory of Open Access Journals (Sweden)

    Harikrishnan Parameswaran

    2011-04-01

    Full Text Available Pulmonary emphysema is a connective tissue disease characterized by the progressive destruction of alveolar walls leading to airspace enlargement and decreased elastic recoil of the lung. However, the relationship between microscopic tissue structure and decline in stiffness of the lung is not well understood. In this study, we developed a 3D computational model of lung tissue in which a pre-strained cuboidal block of tissue was represented by a tessellation of space filling polyhedra, with each polyhedral unit-cell representing an alveolus. Destruction of alveolar walls was mimicked by eliminating faces that separate two polyhedral either randomly or in a spatially correlated manner, in which the highest force bearing walls were removed at each step. Simulations were carried out to establish a link between the geometries that emerged and the rate of decline in bulk modulus of the tissue block. The spatially correlated process set up by the force-based destruction lead to a significantly faster rate of decline in bulk modulus accompanied by highly heterogeneous structures than the random destruction pattern. Using the Karhunen-Loève transformation, an estimator of the change in bulk modulus from the first four moments of airspace cell volumes was setup. Simulations were then obtained for tissue destruction with different idealized alveolar geometry, levels of pre-strain, linear and nonlinear elasticity assumptions for alveolar walls and also mixed destruction patterns where both random and force-based destruction occurs simultaneously. In all these cases, the change in bulk modulus from cell volumes was accurately estimated. We conclude that microscopic structural changes in emphysema and the associated decline in tissue stiffness are linked by the spatial pattern of the destruction process.

  17. DESIGNING OF TOWN SKYLINE ON THE STAGE OF GENERAL LAYOUT

    Directory of Open Access Journals (Sweden)

    Yu. N. Kishik

    2007-01-01

    Full Text Available It is proposed to consider an aggregation of such active elements of town structure as multistoreyed dominants to be used as a basis for designing skyline of a large town on the stage of its general layout. Some interrelated principles, namely: spatial integration, subordination, nature consistence, succession are formulated for improvement of their spatial organization. Every principle takes down any general property of the network of vertical accents which is formed as a system. The obtained principles of the system organization of the multistoreyed dominants are checked while designing Grodno skyline. 

  18. The UA9 experimental layout

    CERN Document Server

    Scandale, W.; Assmann, R.; Bracco, C.; Cerutti, F.; Christiansen, J.; Gilardoni, S.; Laface, E.; Losito, R.; Masi, A.; Metral, E.; Mirarchi, D.; Montesano, S.; Previtali, V.; Redaelli, S.; Valentino, G.; Schoofs, P.; Smirnov, G.; Tlustos, L.; Bagli, E.; Baricordi, S.; Dalpiaz, P.; Guidi, V.; Mazzolari, A.; Vincenzi, D.; Dabagov, S.; Murtas, F.; Carnera, A.; Della Mea, G.; De Salvador, D.; Lombardi, A.; Lytovchenko, O.; Tonezzer, M.; Cavoto, G.; Ludovici, L.; Santacesaria, R.; Valente, P.; Galluccio, F.; Afonin, A.G.; Bulgakov, M.K.; Chesnokov, Yu.A.; Maisheev, V.A.; Yazynin, I.A.; Kovalenko, A.D.; Taratin, A.M.; Gavrikov, Yu.A.; Ivanov, Yu.M.; Lapina, L.P.; Skorobogatov, V.V.; Ferguson, W.; Fulcher, J.; Hall, G.; Pesaresi, M.; Raymond, M.; Rose, A.; Ryan, M.; Zorba, O.; Robert-Demolaize, G.; Markiewicz, T.; Oriunno, M.; Wienands, U.

    2011-01-01

    The UA9 experimental equipment was installed in the CERN-SPS in March '09 with the aim of investigating crystal assisted collimation in coasting mode. Its basic layout comprises silicon bent crystals acting as primary collimators mounted inside two vacuum vessels. A movable 60 cm long block of tungsten located downstream at about 90 degrees phase advance intercepts the deflected beam. Scintillators, Gas Electron Multiplier chambers and other beam loss monitors measure nuclear loss rates induced by the interaction of the beam halo in the crystal. Roman pots are installed in the path of the deflected particles and are equipped with a Medipix detector to reconstruct the transverse distribution of the impinging beam. Finally UA9 takes advantage of an LHC-collimator prototype installed close to the Roman pot to help in setting the beam conditions and to analyze the efficiency to deflect the beam. This paper describes in details the hardware installed to study the crystal collimation during 2010.

  19. Economics of wind farm layout

    Energy Technology Data Exchange (ETDEWEB)

    Germain, A.C. [Wind Energy Resource Specialist, Oakland, CA (United States); Bain, D.A. [Oregon Office of Energy, Portland, OR (United States)

    1997-12-31

    The life cycle cost of energy (COE) is the primary determinant of the economic viability of a wind energy generation facility. The cost of wind turbines and associated hardware is counterbalanced by the energy which can be generated. This paper focuses on the turbine layout design process, considering the cost and energy capture implications of potential spacing options from the viewpoint of a practicing project designer. It is argued that lateral spacings in the range of 1.5 to 5 diameters are all potentially optimal, but only when matched to wind resource characteristics and machine design limits. The effect of wakes on energy capture is quantified while the effect on turbine life and maintenance cost is discussed qualitatively. Careful optimization can lower COE and project designers are encouraged to integrate the concepts in project designs.

  20. Control room lay-out

    International Nuclear Information System (INIS)

    Toma, Violeta

    2004-01-01

    TRIUMF (Tri-University Meson Facility) is Canada's national laboratory for particle and nuclear physics. There are 6 accelerators and 3 Control Rooms at TRIUMF. The main control room serves the big cyclotron, the 500 MeV, and the adjacent experiment. The 42 MeV and two 32 MeV ones are production dedicated. These cyclotrons belong to a private company but are operated by TRIUMF staff from ATG (Applied Technology Group) Control Room. The last is ISAC (Isotope Acceleration and Separation) Control Room, from which the LINAC is controlled. Research areas cover theoretical (2 subjects), pure (5 subjects) and applied (8 subjects) physics. In the early '70s, as the 500 MeV was being completed, the first Control Room was built in the main accelerator building. The recent topics covered by this paper are proton and pion therapy, what are the operator's duties?, the CP42, TR30 and TR13 cyclotron control rooms, the ISAC control systems including control room modification. Due to the nature of an operator's job, the Control Room layout is pretty important. This is true for any work environment, but when working shifts it becomes essential. Lots of time and effort, not to mention money, were spent to figure out the optimum configuration. It seems to me that the key factor in the control room layout is versatility, and this is because it has to keep happy a group of people with different inclinations, which have a tendency to become quite moody after the second night shift. No matter what, there will still be unhappy people, but we are trying our best. (Y. Tanaka)

  1. ST Spot Detector: a web-based application for automatic spot and tissue detection for Spatial Transcriptomics image data sets.

    Science.gov (United States)

    Wong, Kim; Fernández Navarro, José; Bergenstråhle, Ludvig; Ståhl, Patrik L; Lundeberg, Joakim

    2018-01-17

    Spatial transcriptomics (ST) is a method which combines high resolution tissue imaging with high throughput transcriptome sequencing data. This data must be aligned with the images for correct visualisation, a process that involves several manual steps. Here we present ST Spot Detector, a web tool that automates and facilitates this alignment through a user friendly interface. Open source under the MIT license, available from https://github.com/SpatialTranscriptomicsResearch/st_spot_detector. jose.fernandez.navarro@scilifelab.se. Supplementary data are available at Bioinformatics online. © The Author(s) 2018. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

  2. Vegetation response to wagon wheel camp layouts.

    African Journals Online (AJOL)

    Wagon wheel camp layouts have been favoured, in some quarters, for rotational grazing due to the economy and convenience of having the camps radially arranged around central facilities. A possible disadvantage of such layouts is the tendency for over-grazing near the hub and under-grazing at the extremities.

  3. Staking Terraces Online: A Terrace Layout Program

    Science.gov (United States)

    Terrace construction in Missouri exceeded 3 million feet at a cost of over $8 million in 2008. Up to 50 % of the total construction and design time is spent on the terrace layout itself. A web-based computer program, MOTERR, has been developed to design terrace layouts. The program utilizes digital ...

  4. Interactive Graph Layout of a Million Nodes

    Directory of Open Access Journals (Sweden)

    Peng Mi

    2016-12-01

    Full Text Available Sensemaking of large graphs, specifically those with millions of nodes, is a crucial task in many fields. Automatic graph layout algorithms, augmented with real-time human-in-the-loop interaction, can potentially support sensemaking of large graphs. However, designing interactive algorithms to achieve this is challenging. In this paper, we tackle the scalability problem of interactive layout of large graphs, and contribute a new GPU-based force-directed layout algorithm that exploits graph topology. This algorithm can interactively layout graphs with millions of nodes, and support real-time interaction to explore alternative graph layouts. Users can directly manipulate the layout of vertices in a force-directed fashion. The complexity of traditional repulsive force computation is reduced by approximating calculations based on the hierarchical structure of multi-level clustered graphs. We evaluate the algorithm performance, and demonstrate human-in-the-loop layout in two sensemaking case studies. Moreover, we summarize lessons learned for designing interactive large graph layout algorithms on the GPU.

  5. Procedural modeling of urban layout: population, land use, and road network

    NARCIS (Netherlands)

    Lyu, X.; Han, Q.; de Vries, B.

    2017-01-01

    This paper introduces an urban simulation system generating urban layouts with population, road network and land use layers. The desired urban spatial structure is obtained by generating a population map based on population density models. The road network is generated at two spatial levels

  6. Spatial distribution patterns of energy deposition and cellular radiation effects in lung tissue following simulated exposure to alpha particles

    International Nuclear Information System (INIS)

    Hofmann, W.; Crawford-Brown, D.J.

    1990-01-01

    Randomly oriented sections of rat tissue have been digitised to provide the contours of tissue-air interfaces and the locations of individual cell nuclei in the alveolated region of the lung. Sources of alpha particles with varying irradiation geometries and densities are simulated to compute the resulting random pattern of cellular irradiation, i.e. spatial coordinates, frequency, track length, and energy of traversals by the emitted alpha particles. Probabilities per unit track lengths, derived from experimental data on in vitro cellular inactivation and transformation, are then applied to the results of the alpha exposure simulations to yield an estimate of the number of both dead and viable transformed cells and their spatial distributions. If lung cancer risk is linearly related to the number of transformed cells, the carcinogenic risk for hot particles is always smaller than that for a uniform nuclide distribution of the same activity. (author)

  7. Laser-induced fluorescence imaging of subsurface tissue structures with a volume holographic spatial-spectral imaging system.

    Science.gov (United States)

    Luo, Yuan; Gelsinger-Austin, Paul J; Watson, Jonathan M; Barbastathis, George; Barton, Jennifer K; Kostuk, Raymond K

    2008-09-15

    A three-dimensional imaging system incorporating multiplexed holographic gratings to visualize fluorescence tissue structures is presented. Holographic gratings formed in volume recording materials such as a phenanthrenquinone poly(methyl methacrylate) photopolymer have narrowband angular and spectral transmittance filtering properties that enable obtaining spatial-spectral information within an object. We demonstrate this imaging system's ability to obtain multiple depth-resolved fluorescence images simultaneously.

  8. Luminaire layout: Design and implementation

    Science.gov (United States)

    Both, A. J.

    1994-01-01

    The information contained in this report was presented during the discussion regarding guidelines for PAR uniformity in greenhouses. The data shows a lighting uniformity analysis in a research greenhouse for rose production at the Cornell University campus. The luminaire layout was designed using the computer program Lumen-Micro. After implementation of the design, accurate measurements were taken in the greenhouse and the uniformity analysis for both the design and implementation were compared. A study of several supplemental lighting installations resulted in the following recommendations: include only the actual growing area in the lighting uniformity analysis; for growing areas up to 20 square meters, take four measurements per square meter; for growing areas above 20 square meters, take one measurement per square meter; use one of the uniformity criteria and frequency graphs to compare lighting uniformity amongst designs; and design for uniformity criterion of a least 0.75 and the fraction within +/- 15% of the average PAR value should be close to one.

  9. Study to optimize a disposal tunnel layout taking into account heterogeneous characteristics of the geological environment

    International Nuclear Information System (INIS)

    Suyama, Yasuhiro; Toida, Masaru; Yanagizawa, Koichi

    2007-01-01

    The geological environment has spatially heterogeneous characteristics with varied host rock types, fractures and so on. In this case the generic disposal tunnel layout, which has been designed by JNC, is not the most suitable for HLW disposal in Japan. The existence of spatially heterogeneous characteristics means that in the repository region there exist sub-regions that are more favorable from the perspective of long-term safety and ones that are less favorable. In order that the spatially heterogeneous environment itself may be utilized most effectively as an NBS, an alternative design of disposal tunnel layout is required. Focusing on the geological environment with spatially heterogeneous characteristics, the authors have developed an alternative design of disposal tunnel layout. The alternative design adopts an optimization approach using a 'variable disposal tunnel layout'. The optimization approach minimizes the number of locations where major water conducting fractures are intersected, and maximizes the number of emplacement locations for waste packages. This paper will outline the variable disposal tunnel layout and its applicability. (author)

  10. Determination and correlation of spatial distribution of trace elements in normal and neoplastic breast tissues evaluated by μ-XRF

    International Nuclear Information System (INIS)

    Silva, M.P.; Oliveira, M.A.; Poletti, M.E.

    2012-01-01

    Full text: Some trace elements, naturally present in breast tissues, participate in a large number of biological processes, which include among others, activation or inhibition of enzymatic reactions and changes on cell membranes permeability, suggesting that these elements may influence carcinogenic processes. Thus, knowledge of the amounts of these elements and their spatial distribution in normal and neoplastic tissues may help in understanding the role of these elements in the carcinogenic process and tumor progression of breast cancers. Concentrations of trace elements like Ca, Fe, Cu and Zn, previously studied at LNLS using TXRF and conventional XRF, were elevated in neoplastic breast tissues compared to normal tissues. In this study we determined the spatial distribution of these elements in normal and neoplastic breast tissues using μ-XRF technique. We analyzed 22 samples of normal and neoplastic breast tissues (malignant and benign) obtained from paraffin blocks available for study at the Department of Pathology HC-FMRP/USP. From the blocks, a small fraction of material was removed and subjected to histological sections of 60 μm thick made with a microtome. The slices where placed in holder samples and covered with ultralen film. Tissue samples were irradiated with a white beam of synchrotron radiation. The samples were positioned at 45 degrees with respect to the incident beam on a table with 3 freedom degrees (x, y and z), allowing independent positioning of the sample in these directions. The white beam was collimated by a 20 μm microcapillary and samples were fully scanned. At each step, a spectrum was detected for 10 s. The fluorescence emitted by elements present in the sample was detected by a Si (Li) detector with 165 eV at 5.9 keV energy resolution, placed at 90 deg with respect to the incident beam. Results reveal that trace elements Ca-Zn and Fe-Cu could to be correlated in malignant breast tissues. Quantitative results, achieved by Spearman

  11. A biomimetic physiological model for human adipose tissue by adipocytes and endothelial cell cocultures with spatially controlled distribution

    International Nuclear Information System (INIS)

    Yao, Rui; Zhang, Renji; Lin, Feng; Du, Yanan; Luan, Jie

    2013-01-01

    An in vitro model that recapitulates the characteristics of native human adipose tissue would largely benefit pathology studies and therapy development. In this paper, we fabricated a physiological model composed of both human adipocytes and endothelial cells with spatially controlled distribution that biomimics the structure and composition of human adipose tissue. Detailed studies into the cell–cell interactions between the adipocytes and endothelial cells revealed a mutual-enhanced effect which resembles the in vivo routine. Furthermore, comparisons between planar coculture and model coculture demonstrated improved adipocyte function as well as endothelial cell proliferation under the same conditions. This research provided a reliable model for human adipose tissue development studies and potential obesity-related therapy development. (paper)

  12. Automatic Generation of User Interface Layouts for Alternative Screen Orientations

    OpenAIRE

    Zeidler , Clemens; Weber , Gerald; Stuerzlinger , Wolfgang; Lutteroth , Christof

    2017-01-01

    Part 1: Adaptive Design and Mobile Applications; International audience; Creating multiple layout alternatives for graphical user interfaces to accommodate different screen orientations for mobile devices is labor intensive. Here, we investigate how such layout alternatives can be generated automatically from an initial layout. Providing good layout alternatives can inspire developers in their design work and support them to create adaptive layouts. We performed an analysis of layout alternat...

  13. Analysis of skin tissues spatial fluorescence distribution by the Monte Carlo simulation

    International Nuclear Information System (INIS)

    Churmakov, D Y; Meglinski, I V; Piletsky, S A; Greenhalgh, D A

    2003-01-01

    A novel Monte Carlo technique of simulation of spatial fluorescence distribution within the human skin is presented. The computational model of skin takes into account the spatial distribution of fluorophores, which would arise due to the structure of collagen fibres, compared to the epidermis and stratum corneum where the distribution of fluorophores is assumed to be homogeneous. The results of simulation suggest that distribution of auto-fluorescence is significantly suppressed in the near-infrared spectral region, whereas the spatial distribution of fluorescence sources within a sensor layer embedded in the epidermis is localized at an 'effective' depth

  14. Analysis of skin tissues spatial fluorescence distribution by the Monte Carlo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Churmakov, D Y [School of Engineering, Cranfield University, Cranfield, MK43 0AL (United Kingdom); Meglinski, I V [School of Engineering, Cranfield University, Cranfield, MK43 0AL (United Kingdom); Piletsky, S A [Institute of BioScience and Technology, Cranfield University, Silsoe, MK45 4DT (United Kingdom); Greenhalgh, D A [School of Engineering, Cranfield University, Cranfield, MK43 0AL (United Kingdom)

    2003-07-21

    A novel Monte Carlo technique of simulation of spatial fluorescence distribution within the human skin is presented. The computational model of skin takes into account the spatial distribution of fluorophores, which would arise due to the structure of collagen fibres, compared to the epidermis and stratum corneum where the distribution of fluorophores is assumed to be homogeneous. The results of simulation suggest that distribution of auto-fluorescence is significantly suppressed in the near-infrared spectral region, whereas the spatial distribution of fluorescence sources within a sensor layer embedded in the epidermis is localized at an 'effective' depth.

  15. Analysis of skin tissues spatial fluorescence distribution by the Monte Carlo simulation

    Science.gov (United States)

    Y Churmakov, D.; Meglinski, I. V.; Piletsky, S. A.; Greenhalgh, D. A.

    2003-07-01

    A novel Monte Carlo technique of simulation of spatial fluorescence distribution within the human skin is presented. The computational model of skin takes into account the spatial distribution of fluorophores, which would arise due to the structure of collagen fibres, compared to the epidermis and stratum corneum where the distribution of fluorophores is assumed to be homogeneous. The results of simulation suggest that distribution of auto-fluorescence is significantly suppressed in the near-infrared spectral region, whereas the spatial distribution of fluorescence sources within a sensor layer embedded in the epidermis is localized at an `effective' depth.

  16. Organizing vertical layout environments: a forward-looking development strategy for high-rise building projects

    Science.gov (United States)

    Magay, A. A.; Bulgakova, E. A.; Zabelina, S. A.

    2018-03-01

    The article highlights issues surrounding development of high rise buildings. With the rapid increase of the global population there has been a trend for people to migrate into megacities and has caused the expansion of big city territories. This trend, coupled with the desire for a comfortable living environment, has resulted in numerous problems plaguing the megacity. This article proposes that a viable solution to the problems facing megacities is to create vertical layout environments. Potential options for creating vertical layout environments are set out below including the construction of buildings with atriums. Further, the article puts forth suggested spatial organization of the environment as well as optimal landscaping of high-rise buildings and constructions for the creation of vertical layout environments. Finally, the persuasive reasons for the adoption of vertical layout environments is that it will decrease the amount of developed urban areas, decrease traffic and increase environmental sustainability.

  17. An AI-based layout design system for nuclear power plants

    International Nuclear Information System (INIS)

    Fujita, Kikuo; Akagi, Shinsuke; Nakatogawa, Tetsundo; Tanaka, Kazuo; Takeuchi, Makoto.

    1991-01-01

    An AI-based layout design system for nuclear power plants has been developed. The design of the layout of nuclear power plants is a time-consuming task requiring expertise, in which a lot of machinery and equipment must be arranged in a plant building considering various kinds of design constraints, i.e. spatial, functional, economical etc. Computer aided layout design systems have been widely expected and the application of AI technology is expected as a promising approach for the synthesis phase of this task. In this paper, we present an approach to the layout design of nuclear power plants based on a constraint-directed search; one of the AI techniques. In addition, we show how it was implemented with an object-oriented programming technique and give an example of its application. (author)

  18. Layout Optimisation of Wave Energy Converter Arrays

    DEFF Research Database (Denmark)

    Ruiz, Pau Mercadé; Nava, Vincenzo; Topper, Mathew B. R.

    2017-01-01

    This paper proposes an optimisation strategy for the layout design of wave energy converter (WEC) arrays. Optimal layouts are sought so as to maximise the absorbed power given a minimum q-factor, the minimum distance between WECs, and an area of deployment. To guarantee an efficient optimisation......, a four-parameter layout description is proposed. Three different optimisation algorithms are further compared in terms of performance and computational cost. These are the covariance matrix adaptation evolution strategy (CMA), a genetic algorithm (GA) and the glowworm swarm optimisation (GSO) algorithm...

  19. Layout optimization using the homogenization method

    Science.gov (United States)

    Suzuki, Katsuyuki; Kikuchi, Noboru

    1993-01-01

    A generalized layout problem involving sizing, shape, and topology optimization is solved by using the homogenization method for three-dimensional linearly elastic shell structures in order to seek a possibility of establishment of an integrated design system of automotive car bodies, as an extension of the previous work by Bendsoe and Kikuchi. A formulation of a three-dimensional homogenized shell, a solution algorithm, and several examples of computing the optimum layout are presented in this first part of the two articles.

  20. Spatial-temporal ultrasound imaging of residual cavitation bubbles around a fluid-tissue interface in histotripsy.

    Science.gov (United States)

    Hu, Hong; Xu, Shanshan; Yuan, Yuan; Liu, Runna; Wang, Supin; Wan, Mingxi

    2015-05-01

    Cavitation is considered as the primary mechanism of soft tissue fragmentation (histotripsy) by pulsed high-intensity focused ultrasound. The residual cavitation bubbles have a dual influence on the histotripsy pulses: these serve as nuclei for easy generation of new cavitation, and act as strong scatterers causing energy "shadowing." To monitor the residual cavitation bubbles in histotripsy, an ultrafast active cavitation imaging method with relatively high signal-to-noise ratio and good spatial-temporal resolution was proposed in this paper, which combined plane wave transmission, minimum variance beamforming, and coherence factor weighting. The spatial-temporal evolutions of residual cavitation bubbles around a fluid-tissue interface in histotripsy under pulse duration (PD) of 10-40 μs and pulse repetition frequency (PRF) of 0.67-2 kHz were monitored by this method. The integrated bubble area curves inside the tissue interface were acquired from the bubble image sequence, and the formation process of histotripsy damage was estimated. It was observed that the histotripsy efficiency decreased with both longer PDs and higher PRFs. A direct relationship with a coefficient of 1.0365 between histotripsy lesion area and inner residual bubble area was found. These results can assist in monitoring and optimization of the histotripsy treatment further.

  1. Tinjauan Anatomi Layout Halaman Republika Epaper

    Directory of Open Access Journals (Sweden)

    Suprayitno Suprayitno

    2012-10-01

    Full Text Available Communities are increasingly familiar with Internet technology became one of the reasons for the rapid growth of digital newspaper in Indonesia. The ability of the media presents news in brief, fast, accessible and inexpensive form the basis of high growth of consumer interest in digital newspaper / electronic. Technological developments, triggering changes to the newspaper that had shaped the physical print later developed in digital form. In principle, newspaper print and digital newspapers contain messages or the same news, namely providing information to readers about the actual and weighted, as well as other light information that is entertainment. Review the anatomy of the digital newspaper layout is a study to trace and explore what and how the anatomy of a newspaper page layout, at least to provide information and understanding of the anatomy of the layouts in outline. Process layout in the digital version is no different from print media, which distinguishes its output only. In the process to any design layout of a medium, a designer is still expected to possess and master the basic principles such as layout hierarchy, emphasis, balance, and unity. 

  2. Through tissue imaging of a live breast cancer tumour model using handheld surface enhanced spatially offset resonance Raman spectroscopy (SESORRS).

    Science.gov (United States)

    Nicolson, Fay; Jamieson, Lauren E; Mabbott, Samuel; Plakas, Konstantinos; Shand, Neil C; Detty, Michael R; Graham, Duncan; Faulds, Karen

    2018-04-21

    In order to improve patient survival and reduce the amount of unnecessary and traumatic biopsies, non-invasive detection of cancerous tumours is of imperative and urgent need. Multicellular tumour spheroids (MTS) can be used as an ex vivo cancer tumour model, to model in vivo nanoparticle (NP) uptake by the enhanced permeability and retention (EPR) effect. Surface enhanced spatially offset Raman spectroscopy (SESORS) combines both surface enhanced Raman spectroscopy (SERS) and spatially offset Raman spectroscopy (SORS) to yield enhanced Raman signals at much greater sub-surface levels. By utilizing a reporter that has an electronic transition in resonance with the laser frequency, surface enhanced resonance Raman scattering (SERRS) yields even greater enhancement in Raman signal. Using a handheld SORS spectrometer with back scattering optics, we demonstrate the detection of live breast cancer 3D MTS containing SERRS active NPs through 15 mm of porcine tissue. False color 2D heat intensity maps were used to determine tumour model location. In addition, we demonstrate the tracking of SERRS-active NPs through porcine tissue to depths of up to 25 mm. This unprecedented performance is due to the use of red-shifted chalcogenpyrylium-based Raman reporters to demonstrate the novel technique of surface enhanced spatially offset resonance Raman spectroscopy (SESORRS) for the first time. Our results demonstrate a significant step forward in the ability to detect vibrational fingerprints from a tumour model at depth through tissue. Such an approach offers significant promise for the translation of NPs into clinical applications for non-invasive disease diagnostics based on this new chemical principle of measurement.

  3. Computer aided selection of plant layout | Kitaw | Zede Journal

    African Journals Online (AJOL)

    This paper deals with the fundamental concepts of plant layout, in which the need for plant layout, the systematic and logical approaches to the problems, layout solutions and the objectives of plant layout are discussed. Further the approaches and the scoring techniques of the two available computer rout ines are ...

  4. 48 CFR 52.236-17 - Layout of Work.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Layout of Work. 52.236-17... Layout of Work. As prescribed in 36.517, insert the following clause in solicitations and contracts when... need for accurate work layout and for siting verification during work performance: Layout of Work (APR...

  5. Spatial heterogeneity in active chlorophyll fluorescence and PSII activity of coral tissues

    DEFF Research Database (Denmark)

    Ralph, P.J.; Gademann, R.; Larkum, A.W.D.

    2002-01-01

    Chlorophyll-a fluorescence was measured in six species of coral, using pulse-amplitude-modulated fluorometers employing fibre-optic probes with diameters of 8 mm, 1 mm and 140 µm. The 8-mm probe integrated responses over a large area, giving more weight to coenosarc than polyp tissue for Acropora...

  6. Dual growth factor delivery from bilayered, biodegradable hydrogel composites for spatially-guided osteochondral tissue repair

    NARCIS (Netherlands)

    Lu, S.; Lam, J.; Trachtenberg, J.E.; Lee, E.J.; Seyednejad, H.; van den Beucken, J.J.; Tabata, Y.; Wong, M.E.; Jansen, J.A.; Mikos, A.G.; Kasper, F.K.

    2014-01-01

    The present work investigated the use of biodegradable hydrogel composite scaffolds, based on the macromer oligo(poly(ethylene glycol) fumarate) (OPF), to deliver growth factors for the repair of osteochondral tissue in a rabbit model. In particular, bilayered OPF composites were used to mimic the

  7. Analytical Tools for Functional Assessment of Architectural Layouts

    Science.gov (United States)

    Bąkowski, Jarosław

    2017-10-01

    Functional layout of the building, understood as a layout or set of the facility rooms (or groups of rooms) with a system of internal communication, creates an environment and a place of mutual relations between the occupants of the object. Achieving optimal (from the occupants’ point of view) spatial arrangement is possible through activities that often go beyond the stage of architectural design. Adopted in the architectural design, most often during trial and error process or on the basis of previous experience (evidence-based design), functional layout is subject to continuous evaluation and dynamic changing since the beginning of its use. Such verification of the occupancy phase allows to plan future, possible transformations, as well as to develop model solutions for use in other settings. In broader terms, the research hypothesis is to examine whether and how the collected datasets concerning the facility and its utilization can be used to develop methods for assessing functional layout of buildings. In other words, if it is possible to develop an objective method of assessing functional layouts basing on a set of buildings’ parameters: technical, technological and functional ones and whether the method allows developing a set of tools enhancing the design methodology of complex functional objects. By linking the design with the construction phase it is possible to build parametric models of functional layouts, especially in the context of sustainable design or lean design in every aspect: ecological (by reducing the property’s impact on environment), economic (by optimizing its cost) and social (through the implementation of high-performance work environment). Parameterization of size and functional connections of the facility become part of the analyses, as well as the element of model solutions. The “lean” approach means the process of analysis of the existing scheme and consequently - finding weak points as well as means for eliminating these

  8. Spatial Patterns of Excitation at Tissue and Whole Organ Level Due to Early Afterdepolarizations

    Directory of Open Access Journals (Sweden)

    Nele Vandersickel

    2017-06-01

    Full Text Available Early after depolarizations (EAD occur in many pathological conditions, such as congenital or acquired channelopathies, drug induced arrhythmias, and several other situations that are associated with increased arrhythmogenicity. In this paper we present an overview of the relevant computational studies on spatial EAD dynamics in 1D, 2D, and in 3D anatomical models and discuss the relation of EADs to cardiac arrhythmias. We also discuss unsolved problems and highlight new lines of research in this area.

  9. DeveLopment strategy and spatiaL Layout modeL of biomass energy in smaLL towns in coLd region%严寒地区小城镇生物质能发展策略与用地空间布局模式

    Institute of Scientific and Technical Information of China (English)

    张一飞; 赵天宇

    2015-01-01

    为充分利用黑龙江省农业生物质能丰富的优势,运用“能源景观”理论方法,从空间规划层面引导与控制生物质能的发展。通过生产潜能分析,确立黑龙江省生物质能发展指导策略,并通过能源供需分析、时空变异预测,构建基于能源规划和空间规划交叉研究的空间规划改进策略。优化德国、奥地利案例中建立的小城镇与运输成本关系模型,构建适用于黑龙江省的生物质能转换点布局模式。从发展策略与空间布局模式两个角度改变黑龙江省目前生物质能利用效率低、资源浪费严重的现状,优化生物质能消费结构,减少不可再生能源的消耗。%In order to alleviate the energy shortage problem in northeast China,we should make full use of the rich resource of ag-ricultural biomass in Heilongjiang province and apply “energy landscape”theories and methods to guide and control the develop-ment of biomass energy from the perspective of spatial planning.By analyzing biomass energy production potential,Heilongjiang’ s development orientation of biomass energy can be established.Through the analysis of energy supply,demand and temporal, and spatial variation forecast we can improve strategy of space planning on the basis of cross research of energy planning and spa-tial planning.After revising the model of relation between settlements and transportation cost created on the basis of Germany and Austria’s case experience the planning pattern of biomass energy production land can be developped.Using development strategy and spatial layout model,the biomass energy consumption structure can be optimized and non-renewable energy con-sumption can be reduced indirectly.

  10. Tissue

    Directory of Open Access Journals (Sweden)

    David Morrissey

    2012-01-01

    Full Text Available Purpose. In vivo gene therapy directed at tissues of mesenchymal origin could potentially augment healing. We aimed to assess the duration and magnitude of transene expression in vivo in mice and ex vivo in human tissues. Methods. Using bioluminescence imaging, plasmid and adenoviral vector-based transgene expression in murine quadriceps in vivo was examined. Temporal control was assessed using a doxycycline-inducible system. An ex vivo model was developed and optimised using murine tissue, and applied in ex vivo human tissue. Results. In vivo plasmid-based transgene expression did not silence in murine muscle, unlike in liver. Although maximum luciferase expression was higher in muscle with adenoviral delivery compared with plasmid, expression reduced over time. The inducible promoter cassette successfully regulated gene expression with maximum levels a factor of 11 greater than baseline. Expression was re-induced to a similar level on a temporal basis. Luciferase expression was readily detected ex vivo in human muscle and tendon. Conclusions. Plasmid constructs resulted in long-term in vivo gene expression in skeletal muscle, in a controllable fashion utilising an inducible promoter in combination with oral agents. Successful plasmid gene transfection in human ex vivo mesenchymal tissue was demonstrated for the first time.

  11. Evaluating Direct Manipulation Operations for Constraint-Based Layout

    OpenAIRE

    Zeidler , Clemens; Lutteroth , Christof; Stuerzlinger , Wolfgang; Weber , Gerald

    2013-01-01

    Part 11: Interface Layout and Data Entry; International audience; Layout managers are used to control the placement of widgets in graphical user interfaces (GUIs). Constraint-based layout managers are more powerful than other ones. However, they are also more complex and their layouts are prone to problems that usually require direct editing of constraints. Today, designers commonly use GUI builders to specify GUIs. The complexities of traditional approaches to constraint-based layouts pose c...

  12. An optimization tool for satellite equipment layout

    Science.gov (United States)

    Qin, Zheng; Liang, Yan-gang; Zhou, Jian-ping

    2018-01-01

    Selection of the satellite equipment layout with performance constraints is a complex task which can be viewed as a constrained multi-objective optimization and a multiple criteria decision making problem. The layout design of a satellite cabin involves the process of locating the required equipment in a limited space, thereby satisfying various behavioral constraints of the interior and exterior environments. The layout optimization of satellite cabin in this paper includes the C.G. offset, the moments of inertia and the space debris impact risk of the system, of which the impact risk index is developed to quantify the risk to a satellite cabin of coming into contact with space debris. In this paper an optimization tool for the integration of CAD software as well as the optimization algorithms is presented, which is developed to automatically find solutions for a three-dimensional layout of equipment in satellite. The effectiveness of the tool is also demonstrated by applying to the layout optimization of a satellite platform.

  13. The Influence of Hierarchy and Layout Geometry in the Design of Learning Spaces

    Science.gov (United States)

    Smith, Charlie

    2017-01-01

    For a number of years, higher education has moved away from didactic teaching toward collaborative and self-directed learning. This paper discusses how the configuration and spatial geometry of learning spaces influences engagement and interaction, with a particular focus on hierarchies between people within the space. Layouts, presented as…

  14. 2007 Effect of Changes in Layout Shape on Unit Construction Cost

    African Journals Online (AJOL)

    ezra

    The shape of a building layout is the spatial attribute that defines the outline of the building. ... The results of this study indicate that perimeter-to-floor ratio, unit construction ... Design variables have been defined as the .... The objective of this paper is to explore the effect ... preparation of cost estimate, changing of design.

  15. Layout Optimisation of Wave Energy Converter Arrays

    Directory of Open Access Journals (Sweden)

    Pau Mercadé Ruiz

    2017-08-01

    Full Text Available This paper proposes an optimisation strategy for the layout design of wave energy converter (WEC arrays. Optimal layouts are sought so as to maximise the absorbed power given a minimum q-factor, the minimum distance between WECs, and an area of deployment. To guarantee an efficient optimisation, a four-parameter layout description is proposed. Three different optimisation algorithms are further compared in terms of performance and computational cost. These are the covariance matrix adaptation evolution strategy (CMA, a genetic algorithm (GA and the glowworm swarm optimisation (GSO algorithm. The results show slightly higher performances for the latter two algorithms; however, the first turns out to be significantly less computationally demanding.

  16. Discrete optimization in architecture architectural & urban layout

    CERN Document Server

    Zawidzki, Machi

    2016-01-01

    This book presents three projects that demonstrate the fundamental problems of architectural design and urban composition – the layout design, evaluation and optimization. Part I describes the functional layout design of a residential building, and an evaluation of the quality of a town square (plaza). The algorithm for the functional layout design is based on backtracking using a constraint satisfaction approach combined with coarse grid discretization. The algorithm for the town square evaluation is based on geometrical properties derived directly from its plan. Part II introduces a crowd-simulation application for the analysis of escape routes on floor plans, and optimization of a floor plan for smooth crowd flow. The algorithms presented employ agent-based modeling and cellular automata.

  17. CMOS circuit design, layout and simulation

    CERN Document Server

    Baker, R Jacob

    2010-01-01

    The Third Edition of CMOS Circuit Design, Layout, and Simulation continues to cover the practical design of both analog and digital integrated circuits, offering a vital, contemporary view of a wide range of analog/digital circuit blocks including: phase-locked-loops, delta-sigma sensing circuits, voltage/current references, op-amps, the design of data converters, and much more. Regardless of one's integrated circuit (IC) design skill level, this book allows readers to experience both the theory behind, and the hands-on implementation of, complementary metal oxide semiconductor (CMOS) IC design via detailed derivations, discussions, and hundreds of design, layout, and simulation examples.

  18. Reference-free determination of tissue absorption coefficient by modulation transfer function characterization in spatial frequency domain.

    Science.gov (United States)

    Chen, Weiting; Zhao, Huijuan; Li, Tongxin; Yan, Panpan; Zhao, Kuanxin; Qi, Caixia; Gao, Feng

    2017-08-08

    Spatial frequency domain (SFD) measurement allows rapid and non-contact wide-field imaging of the tissue optical properties, thus has become a potential tool for assessing physiological parameters and therapeutic responses during photodynamic therapy of skin diseases. The conventional SFD measurement requires a reference measurement within the same experimental scenario as that for a test one to calibrate mismatch between the real measurements and the model predictions. Due to the individual physical and geometrical differences among different tissues, organs and patients, an ideal reference measurement might be unavailable in clinical trials. To address this problem, we present a reference-free SFD determination of absorption coefficient that is based on the modulation transfer function (MTF) characterization. Instead of the absolute amplitude that is used in the conventional SFD approaches, we herein employ the MTF to characterize the propagation of the modulated lights in tissues. With such a dimensionless relative quantity, the measurements can be naturally corresponded to the model predictions without calibrating the illumination intensity. By constructing a three-dimensional database that portrays the MTF as a function of the optical properties (both the absorption coefficient μ a and the reduced scattering coefficient [Formula: see text]) and the spatial frequency, a look-up table approach or a least-square curve-fitting method is readily applied to recover the absorption coefficient from a single frequency or multiple frequencies, respectively. Simulation studies have verified the feasibility of the proposed reference-free method and evaluated its accuracy in the absorption recovery. Experimental validations have been performed on homogeneous tissue-mimicking phantoms with μ a ranging from 0.01 to 0.07 mm -1 and [Formula: see text] = 1.0 or 2.0 mm -1 . The results have shown maximum errors of 4.86 and 7% for [Formula: see text] = 1.0 mm -1 and

  19. Interior spatial layout with soft objectives using evolutionary computation

    NARCIS (Netherlands)

    Chatzikonstantinou, I.; Bengisu, E.

    2016-01-01

    This paper presents the design problem of furniture arrangement in a residential interior living space, and addresses it by means of evolutionary computation. Interior arrangement is an important and interesting problem that occurs commonly when designing living spaces. It entails determining the

  20. Final Report: ATLAS Phase-2 Tracker Upgrade Layout Task Force

    CERN Document Server

    Clark, A; The ATLAS collaboration; Hessey, N; Mättig, P; Styles, N; Wells, P; Burdin, S; Cornelissen, T; Todorov, T; Vankov, P; Watson, I; Wenig, S

    2012-01-01

    he mandate of the Upgrade Layout Task Force was to develop a benchmark layout proposal for the ATLAS Phase-2 Upgrade Letter of Intent (LOI), due in late 2012. The work described in this note has evolved from simulation and design studies made using an earlier "UTOPIA" upgrade tracker layout, and experience gained from the current ATLAS Inner Detector during the first years of data taking. The layout described in this document, called the LoI-layout, will be used as a benchmark layout for the LoI and will be used for simulation and engineering studies described in the LoI.

  1. Intersection layout, traffic volumes and accidents.

    NARCIS (Netherlands)

    Poppe, F.

    1988-01-01

    This paper reports on the accident research carried out as a part of a large project started in 1983. For this accident research an inventory was made of a large number of intersections.Recorded were layout features, accident data and estimates of traffic volumes. Attention will be given to the

  2. Concept Layout Model of Transportation Terminals

    Directory of Open Access Journals (Sweden)

    Li-ya Yao

    2012-01-01

    Full Text Available Transportation terminal is the key node in transport systems. Efficient terminals can improve operation of passenger transportation networks, adjust the layout of public transportation networks, provide a passenger guidance system, and regulate the development of commercial forms, as well as optimize the assembly and distribution of modern logistic modes, among others. This study aims to clarify the relationship between the function and the structure of transportation terminals and establish the function layout design. The mapping mechanism of demand, function, and structure was analyzed, and a quantitative relationship between function and structure was obtained from a design perspective. Passenger demand and terminal structure were decomposed into several demand units and structural elements following the principle of reverse engineering. The relationship maps between these two kinds of elements were then analyzed. Function-oriented concept layout model of transportation terminals was established using the previous method. Thus, a technique in planning and design of transportation structures was proposed. Meaningful results were obtained from the optimization of transportation terminal facilities, which guide the design of the functional layout of transportation terminals and improve the development of urban passenger transportation systems.

  3. Terrace Layout Using a Computer Assisted System

    Science.gov (United States)

    Development of a web-based terrace design tool based on the MOTERR program is presented, along with representative layouts for conventional and parallel terrace systems. Using digital elevation maps and geographic information systems (GIS), this tool utilizes personal computers to rapidly construct ...

  4. Customisation of Indico pages - Layout and Menus

    CERN Multimedia

    CERN. Geneva; Ferreira, Pedro

    2017-01-01

    In this tutorial you are going to learn how to customize the layout of your Indico pages (for example you can change the color of the background images or change the logo) and the menus on your Indico pages  (for example you can add or hide certain blocks, or change their name and order).  

  5. You Be the Judge: Newspaper Advertising Layout.

    Science.gov (United States)

    Koeninger, Jimmy G.

    The learning package is designed to provide the marketing educator with a culminating activity for an instructional unit focusing on advertising layout principles and procedures. It is to be used in conjunction with 35mm slides of newspaper advertisements, which the student views and rates in comparison with the ratings of a panel of experts. A…

  6. Hardware and layout aspects affecting maintainability

    International Nuclear Information System (INIS)

    Jayaraman, V.N.; Surendar, Ch.

    1977-01-01

    It has been found from maintenance experience at the Rajasthan Atomic Power Station that proper hardware and instrumentation layout can reduce maintenance and down-time on the related equipment. The problems faced in this connection and how they were solved is narrated. (M.G.B.)

  7. Optimal Wafer Cutting in Shuttle Layout Problems

    DEFF Research Database (Denmark)

    Nisted, Lasse; Pisinger, David; Altman, Avri

    2011-01-01

    . The shuttle layout problem is frequently solved in two phases: first, a floorplan of the shuttle is generated. Then, a cutting plan is found which minimizes the overall number of wafers needed to satisfy the demand of each die type. Since some die types require special production technologies, only compatible...

  8. Beam Dynamics and Layout arXiv

    CERN Document Server

    Lombardi, Alessandra

    In this paper, we give some guidelines for the design of linear accelerators, with special emphasis on their use in a hadron therapy facility. We concentrate on two accelerator layouts, based on linacs. The conventional one based on a linac injecting into a synchrotron and a all-linac solution based on high gradient high frequency RF cavities.

  9. Spatial accuracy of 3D reconstructed radioluminographs of serial tissue sections and resultant absorbed dose estimates

    Energy Technology Data Exchange (ETDEWEB)

    Petrie, I.A.; Flynn, A.A.; Pedley, R.B.; Green, A.J.; El-Emir, E.; Dearling, J.L.J.; Boxer, G.M.; Boden, R.; Begent, R.H.J. [Cancer Research UK Targeting and Imaging Group, Department of Oncology, Royal Free and University College Medical School, Royal Free Campus, London (United Kingdom)

    2002-10-21

    Many agents using tumour-associated characteristics are deposited heterogeneously within tumour tissue. Consequently, tumour heterogeneity should be addressed when obtaining information on tumour biology or relating absorbed radiation dose to biological effect. We present a technique that enables radioluminographs of serial tumour sections to be reconstructed using automated computerized techniques, resulting in a three-dimensional map of the dose-rate distribution of a radiolabelled antibody. The purpose of this study is to assess the reconstruction accuracy. Furthermore, we estimate the potential error resulting from registration misalignment, for a range of beta-emitting radionuclides. We compare the actual dose-rate distribution with that obtained from the same activity distribution but with manually defined translational and rotational shifts. As expected, the error produced with the short-range {sup 14}C is much larger than that for the longer range {sup 90}Y; similarly values for the medium range {sup 131}I are between the two. Thus, the impact of registration inaccuracies is greater for short-range sources. (author)

  10. Spatial distribution of the trace elements zinc, strontium and lead in human bone tissue.

    Science.gov (United States)

    Pemmer, B; Roschger, A; Wastl, A; Hofstaetter, J G; Wobrauschek, P; Simon, R; Thaler, H W; Roschger, P; Klaushofer, K; Streli, C

    2013-11-01

    Trace elements are chemical elements in minute quantities, which are known to accumulate in the bone. Cortical and trabecular bones consist of bone structural units (BSUs) such as osteons and bone packets of different mineral content and are separated by cement lines. Previous studies investigating trace elements in bone lacked resolution and therefore very little is known about the local concentration of zinc (Zn), strontium (Sr) and lead (Pb) in BSUs of human bone. We used synchrotron radiation induced micro X-ray fluorescence analysis (SR μ-XRF) in combination with quantitative backscattered electron imaging (qBEI) to determine the distribution and accumulation of Zn, Sr, and Pb in human bone tissue. Fourteen human bone samples (10 femoral necks and 4 femoral heads) from individuals with osteoporotic femoral neck fractures as well as from healthy individuals were analyzed. Fluorescence intensity maps were matched with BE images and correlated with calcium (Ca) content. We found that Zn and Pb had significantly increased levels in the cement lines of all samples compared to the surrounding mineralized bone matrix. Pb and Sr levels were found to be correlated with the degree of mineralization. Interestingly, Zn intensities had no correlation with Ca levels. We have shown for the first time that there is a differential accumulation of the trace elements Zn, Pb and Sr in BSUs of human bone indicating different mechanisms of accumulation. © 2013. Published by Elsevier Inc. All rights reserved.

  11. Low Carbon Design Research on the Space Layout Types of Office Buildings

    Science.gov (United States)

    Xia, Bing

    2018-01-01

    It is beneficial to find out the relationship of the spatial layout and low-carbon design in order to reduce buildings’ carbon emissions in the conceptual design phase. This paper analyzes and compares shape coefficient values, annual energy consumption and lighting performance of office buildings of different space layout types in Shanghai. Based on morphological characteristics of different types, the study also analyzes and presents low-carbon design strategies for each single type. This study assumes that architects should conduct passive and active design according to the specific building space layout, so that to make best use of the advantages and bypassing the disadvantages, in order to maximally reduce buildings’ carbon emissions.

  12. Spatial interaction between tissue pressure and skeletal muscle perfusion during contraction.

    Science.gov (United States)

    van Donkelaar, C C; Huyghe, J M; Vankan, W J; Drost, M R

    2001-05-01

    The vascular waterfall theory attributes decreased muscle perfusion during contraction to increased intramuscular pressure (P(IM)) and concomitant increase in venous resistance. Although P(IM) is distributed during contractions, this theory does not account for heterogeneity. This study hypothesises that pressure heterogeneity could affect the interaction between P(IM) rise and perfusion. Regional tissue perfusion during submaximum (100kPa) tetanic contraction is studied, using a finite element model of perfused contracting skeletal muscle. Capillary flow in muscles with one proximal artery and vein (SIM(1)) and with an additional distal artery and vein (SIM(2)) is compared. Blood flow and pressures at rest and P(IM) during contraction ( approximately 25kPa maximally) are similar between simulations, but capillary flow and venous pressure differ. In SIM(2), venous pressure and capillary flow correspond to P(IM) distribution, whereas capillary flow in SIM(1) is less than 10% of flow in SIM(2), in the muscle half without draining vein. This difference is caused by a high central P(IM), followed by central venous pressure rise, in agreement with the waterfall theory. The high central pressure (SIM(1)), obstructs outflow from the distal veins. Distal venous pressure rises until central blood pressure is reached, although local P(IM) is low. Adding a distal vein (SIM(2)) restores the perfusion. It is concluded that regional effects contribute to the interaction between P(IM) and perfusion during contraction. Unlike stated by the vascular waterfall theory, venous pressure may locally exceed P(IM). Although this can be explained by the principles of this theory, the theory does not include this phenomenon as such.

  13. Multiobjective Optimization for Fixture Locating Layout of Sheet Metal Part Using SVR and NSGA-II

    Directory of Open Access Journals (Sweden)

    Yuan Yang

    2017-01-01

    Full Text Available Fixture plays a significant role in determining the sheet metal part (SMP spatial position and restraining its excessive deformation in many manufacturing operations. However, it is still a difficult task to design and optimize SMP fixture locating layout at present because there exist multiple conflicting objectives and excessive computational cost of finite element analysis (FEA during the optimization process. To this end, a new multiobjective optimization method for SMP fixture locating layout is proposed in this paper based on the support vector regression (SVR surrogate model and the elitist nondominated sorting genetic algorithm (NSGA-II. By using ABAQUS™ Python script interface, a parametric FEA model is established. And the fixture locating layout is treated as design variables, while the overall deformation and maximum deformation of SMP under external forces are as the multiple objective functions. First, a limited number of training and testing samples are generated by combining Latin hypercube design (LHD with FEA. Second, two SVR prediction models corresponding to the multiple objectives are established by learning from the limited training samples and are integrated as the multiobjective optimization surrogate model. Third, NSGA-II is applied to determine the Pareto optimal solutions of SMP fixture locating layout. Finally, a multiobjective optimization for fixture locating layout of an aircraft fuselage skin case is conducted to illustrate and verify the proposed method.

  14. Automatic Constraint Detection for 2D Layout Regularization.

    Science.gov (United States)

    Jiang, Haiyong; Nan, Liangliang; Yan, Dong-Ming; Dong, Weiming; Zhang, Xiaopeng; Wonka, Peter

    2016-08-01

    In this paper, we address the problem of constraint detection for layout regularization. The layout we consider is a set of two-dimensional elements where each element is represented by its bounding box. Layout regularization is important in digitizing plans or images, such as floor plans and facade images, and in the improvement of user-created contents, such as architectural drawings and slide layouts. To regularize a layout, we aim to improve the input by detecting and subsequently enforcing alignment, size, and distance constraints between layout elements. Similar to previous work, we formulate layout regularization as a quadratic programming problem. In addition, we propose a novel optimization algorithm that automatically detects constraints. We evaluate the proposed framework using a variety of input layouts from different applications. Our results demonstrate that our method has superior performance to the state of the art.

  15. Automatic Constraint Detection for 2D Layout Regularization

    KAUST Repository

    Jiang, Haiyong

    2015-09-18

    In this paper, we address the problem of constraint detection for layout regularization. As layout we consider a set of two-dimensional elements where each element is represented by its bounding box. Layout regularization is important for digitizing plans or images, such as floor plans and facade images, and for the improvement of user created contents, such as architectural drawings and slide layouts. To regularize a layout, we aim to improve the input by detecting and subsequently enforcing alignment, size, and distance constraints between layout elements. Similar to previous work, we formulate the layout regularization as a quadratic programming problem. In addition, we propose a novel optimization algorithm to automatically detect constraints. In our results, we evaluate the proposed framework on a variety of input layouts from different applications, which demonstrates our method has superior performance to the state of the art.

  16. Automatic Constraint Detection for 2D Layout Regularization

    KAUST Repository

    Jiang, Haiyong; Nan, Liangliang; Yan, Dongming; Dong, Weiming; Zhang, Xiaopeng; Wonka, Peter

    2015-01-01

    plans or images, such as floor plans and facade images, and for the improvement of user created contents, such as architectural drawings and slide layouts. To regularize a layout, we aim to improve the input by detecting and subsequently enforcing

  17. Improving Tumor Treating Fields Treatment Efficacy in Patients With Glioblastoma Using Personalized Array Layouts

    Energy Technology Data Exchange (ETDEWEB)

    Wenger, Cornelia, E-mail: cwenger@fc.ul.pt [Institute of Biophysics and Biomedical Engineering, Faculdade de Ciências, Universidade de Lisboa, Lisbon (Portugal); Salvador, Ricardo [Institute of Biophysics and Biomedical Engineering, Faculdade de Ciências, Universidade de Lisboa, Lisbon (Portugal); Basser, Peter J. [Section on Tissue Biophysics and Biomimetics, Eunice Kennedy Shriver National Institute of Child Health and Human Development, National Institutes of Health, Bethesda, Maryland (United States); Miranda, Pedro C. [Institute of Biophysics and Biomedical Engineering, Faculdade de Ciências, Universidade de Lisboa, Lisbon (Portugal)

    2016-04-01

    Purpose: To investigate tumors of different size, shape, and location and the effect of varying transducer layouts on Tumor Treating Fields (TTFields) distribution in an anisotropic model. Methods and Materials: A realistic human head model was generated from MR images of 1 healthy subject. Four different virtual tumors were placed at separate locations. The transducer arrays were modeled to mimic the TTFields-delivering commercial device. For each tumor location, varying array layouts were tested. The finite element method was used to calculate the electric field distribution, taking into account tissue heterogeneity and anisotropy. Results: In all tumors, the average electric field induced by either of the 2 perpendicular array layouts exceeded the 1-V/cm therapeutic threshold value for TTFields effectiveness. Field strength within a tumor did not correlate with its size and shape but was higher in more superficial tumors. Additionally, it always increased when the array was adapted to the tumor's location. Compared with a default layout, the largest increase in field strength was 184%, and the highest average field strength induced in a tumor was 2.21 V/cm. Conclusions: These results suggest that adapting array layouts to specific tumor locations can significantly increase field strength within the tumor. Our findings support the idea of personalized treatment planning to increase TTFields efficacy for patients with GBM.

  18. Improving Tumor Treating Fields Treatment Efficacy in Patients With Glioblastoma Using Personalized Array Layouts

    International Nuclear Information System (INIS)

    Wenger, Cornelia; Salvador, Ricardo; Basser, Peter J.; Miranda, Pedro C.

    2016-01-01

    Purpose: To investigate tumors of different size, shape, and location and the effect of varying transducer layouts on Tumor Treating Fields (TTFields) distribution in an anisotropic model. Methods and Materials: A realistic human head model was generated from MR images of 1 healthy subject. Four different virtual tumors were placed at separate locations. The transducer arrays were modeled to mimic the TTFields-delivering commercial device. For each tumor location, varying array layouts were tested. The finite element method was used to calculate the electric field distribution, taking into account tissue heterogeneity and anisotropy. Results: In all tumors, the average electric field induced by either of the 2 perpendicular array layouts exceeded the 1-V/cm therapeutic threshold value for TTFields effectiveness. Field strength within a tumor did not correlate with its size and shape but was higher in more superficial tumors. Additionally, it always increased when the array was adapted to the tumor's location. Compared with a default layout, the largest increase in field strength was 184%, and the highest average field strength induced in a tumor was 2.21 V/cm. Conclusions: These results suggest that adapting array layouts to specific tumor locations can significantly increase field strength within the tumor. Our findings support the idea of personalized treatment planning to increase TTFields efficacy for patients with GBM.

  19. 48 CFR 36.517 - Layout of work.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Layout of work. 36.517... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.517 Layout of work. The contracting officer shall insert the clause at 52.236-17, Layout of Work, in solicitations and contracts when...

  20. Pure JavaScript Storyline Layout Algorithm

    Energy Technology Data Exchange (ETDEWEB)

    2017-10-02

    This is a JavaScript library for a storyline layout algorithm. Storylines are adept at communicating complex change by encoding time on the x-axis and using the proximity of lines in the y direction to represent interaction between entities. The library in this disclosure takes as input a list of objects containing an id, time, and state. The output is a data structure that can be used to conveniently render a storyline visualization. Most importantly, the library computes the y-coordinate of the entities over time that decreases layout artifacts including crossings, wiggles, and whitespace. This is accomplished through multi-objective, multi-stage optimization problem, where the output of one stage produces input and constraints for the next stage.

  1. Concept Layout Model of Transportation Terminals

    OpenAIRE

    Yao, Li-ya; Sun, Li-shan; Wang, Wu-hong; Xiong, Hui

    2012-01-01

    Transportation terminal is the key node in transport systems. Efficient terminals can improve operation of passenger transportation networks, adjust the layout of public transportation networks, provide a passenger guidance system, and regulate the development of commercial forms, as well as optimize the assembly and distribution of modern logistic modes, among others. This study aims to clarify the relationship between the function and the structure of transportation terminals and establish ...

  2. CLASSIFICATION OF THE MGR SITE LAYOUT SYSTEM

    International Nuclear Information System (INIS)

    S.E. Salzman

    1999-01-01

    The purpose of this analysis is to document the Quality Assurance (QA) classification of the Monitored Geologic Repository (MGR) site layout system structures, systems and components (SSCs) performed by the MGR Safety Assurance Department. This analysis also provides the basis for revision of YMP/90-55Q, Q-List (YMP 1998). The Q-List identifies those MGR SSCs subject to the requirements of DOE/RW-0333P, ''Quality Assurance Requirements and Description'' (QARD) (DOE 1998)

  3. Inverse procedural modeling of facade layouts

    KAUST Repository

    Wu, Feng; Yan, Dongming; Dong, Weiming; Zhang, Xiaopeng; Wonka, Peter

    2014-01-01

    In this paper, we address the following research problem: How can we generate a meaningful split grammar that explains a given facade layout? To evaluate if a grammar is meaningful, we propose a cost function based on the description length and minimize this cost using an approximate dynamic programming framework. Our evaluation indicates that our framework extracts meaningful split grammars that are competitive with those of expert users, while some users and all competing automatic solutions are less successful. Copyright © ACM.

  4. Ergonomic Application on the Work Station Layout

    International Nuclear Information System (INIS)

    Suharyo Widagdo; Darlis

    2003-01-01

    Work station layout in the ideal way has been made. The dimension of the work station is 9.4 m x 7.1 m. The workers to be stationed should feel comfort. This can be done by honoring the dimensions and the sum of the tools that should be stationed and also the free space that should be mention between the tools as state in EPRI, NP-2411. (author)

  5. Inverse procedural modeling of facade layouts

    KAUST Repository

    Wu, Feng

    2014-07-22

    In this paper, we address the following research problem: How can we generate a meaningful split grammar that explains a given facade layout? To evaluate if a grammar is meaningful, we propose a cost function based on the description length and minimize this cost using an approximate dynamic programming framework. Our evaluation indicates that our framework extracts meaningful split grammars that are competitive with those of expert users, while some users and all competing automatic solutions are less successful. Copyright © ACM.

  6. Improved Layout of Inverter for EMC Analysis

    OpenAIRE

    Yade , Ousseynou; Martin , Christian; Vollaire , Christian; Bréard , Arnaud; Ali , Marwan; Meuret , Régis; Hervé , Morel

    2017-01-01

    International audience; This paper details EMC (electromagnetic compatibility) analysis on an inverter application. The work deals with the whole power chain (±270Vdc input voltage to 3-phase 115 Vac output voltage). This inverter is composed by modular parts (power module and EMC filters) that supply motors in more electrical aircraft. Through our analysis an approach is defined to design a detailed lumped circuit model of the power module layout by using Q3D extractor and SABER software. Fr...

  7. Optimization of a furniture factory layout

    Directory of Open Access Journals (Sweden)

    Tadej Kanduč

    2015-03-01

    Full Text Available This paper deals with the problem of optimizing a factory floor layout in a Slovenian furniture factory. First, the current state of the manufacturing system is analyzed by constructing a discrete event simulation (DES model that reflects the manufacturing processes. The company produces over 10,000 different products, and their manufacturing processes include approximately 30,000 subprocesses. Therefore, manually constructing a model to include every subprocess is not feasible. To overcome this problem, a method for automated model construction was developed to construct a DES model based on a selection of manufacturing orders and relevant subprocesses. The obtained simulation model provided insight into the manufacturing processes and enable easy modification of model parameters for optimizing the manufacturing processes. Finally, the optimization problem was solved: the total distance the products had to traverse between machines was minimized by devising an optimal machine layout. With the introduction of certain simplifications, the problem was best described as a quadratic assignment problem. A novel heuristic method based on force-directed graph drawing algorithms was developed. Optimizing the floor layout resulted in a significant reduction of total travel distance for the products.

  8. Production layout improvement by using line balancing and Systematic Layout Planning (SLP) at PT. XYZ

    Science.gov (United States)

    Buchari; Tarigan, U.; Ambarita, M. B.

    2018-02-01

    PT. XYZ is a wood processing company which produce semi-finished wood with production system is make to order. In the production process, it can be seen that the production line is not balanced. The imbalance of the production line is caused by the difference in cycle time between work stations. In addition, there are other issues, namely the existence of material flow pattern is irregular so it resulted in the backtracking and displacement distance away. This study aimed to obtain the allocation of work elements to specific work stations and propose an improvement of the production layout based on the result of improvements in the line balancing. The method used in the balancing is Ranked Positional Weight (RPW) or also known as Helgeson Birnie method. While the methods used in the improvement of the layout is the method of Systematic Layout Planning (SLP). By using Ranked Positional Weight (RPW) obtained increase in line efficiency becomes 84,86% and decreased balance delay becomes 15,14%. Repairing the layout using the method of Systematic Layout Planning (SLP) also give good results with a reduction in path length becomes 133,82 meters from 213,09 meters previously or a decrease of 37.2%.

  9. A REDESIGN LAYOUT TO INCREASE PRODUCTIVITY OF A COMPANY

    Directory of Open Access Journals (Sweden)

    Vincentia Kitriastika

    2013-06-01

    Full Text Available This project is conducted in Company X, a passenger cars wheel producing company located in Sunter, North Jakarta. With a view of increasing the productivity of the company, the focus of this project will be redesigned the layout of the factory. The main problem encountered is that the goods are not produced in single location, causing a considerable hindrance in terms of time and distance, and hence efficiency. The redesigning layout process will use SLP method and flow analysis while supported by analysis of assembly line balancing to optimize the layout. Regarding the evaluation process, ARENA software will be used to simulate and identify the bottleneck in the production process, and comparing the layout alternatives to decide the best layout. The best chosen layout according to the simulation and SLP method that supported with flow analysis and assembly line balancing will be used as the master draft layout that will be proposed to Company X.

  10. Tumor spatial heterogeneity in myxoid-containing soft tissue using texture analysis of diffusion-weighted MRI.

    Directory of Open Access Journals (Sweden)

    Hyun Su Kim

    Full Text Available The objective of this study was to examine the tumor spatial heterogeneity in myxoid-containing soft-tissue tumors (STTs using texture analysis of diffusion-weighted imaging (DWI. A total of 40 patients with myxoid-containing STTs (23 benign and 17 malignant were included in this study. The region of interest (ROI was manually drawn on the apparent diffusion coefficient (ADC map. For texture analysis, the global (mean, standard deviation, skewness, and kurtosis, regional (intensity variability and size-zone variability, and local features (energy, entropy, correlation, contrast, homogeneity, variance, and maximum probability were extracted from the ADC map. Student's t-test was used to test the difference between group means. Analysis of covariance (ANCOVA was performed with adjustments for age, sex, and tumor volume. The receiver operating characteristic (ROC analysis was performed to compare diagnostic performances. Malignant myxoid-containing STTs had significantly higher kurtosis (P = 0.040, energy (P = 0.034, correlation (P<0.001, and homogeneity (P = 0.003, but significantly lower contrast (P<0.001 and variance (P = 0.001 compared with benign myxoid-containing STTs. Contrast showed the highest area under the curve (AUC = 0.923, P<0.001, sensitivity (94.12%, and specificity (86.96%. Our results reveal the potential utility of texture analysis of ADC maps for differentiating benign and malignant myxoid-containing STTs.

  11. General layout of a 1300 MW PWR buildings: standard lay-out and influence factors

    International Nuclear Information System (INIS)

    Silva Messias, M. da

    1986-01-01

    The Standardization concept of a 1300 MW Nuclear Power Plant equipped with pressurized-water reactors (PWR) will be considered with regard to the factors which have various degrees of influence on the Layout of the Site. Standardization with regard to the Layout of nuclear power plant, stands, however also for a fixed arrangement of the components in the main buildings and a fixed arrangement of the buildings in the site plan. Standardization may result in simplified and shorter licensing procedures and mean less planning effort. Concentration of systems, optimization of the electro-mechanical design, clear separation of the controlled area, need for shielding, maintenance and safety aspects are some of number of factors which have various degress of influence on the layout of the buildings. (Author) [pt

  12. Repository surface design site layout analysis

    International Nuclear Information System (INIS)

    Montalvo, H.R.

    1998-01-01

    The purpose of this analysis is to establish the arrangement of the Yucca Mountain Repository surface facilities and features near the North Portal. The analysis updates and expands the North Portal area site layout concept presented in the ACD, including changes to reflect the resizing of the Waste Handling Building (WHB), Waste Treatment Building (WTB), Carrier Preparation Building (CPB), and site parking areas; the addition of the Carrier Washdown Buildings (CWBs); the elimination of the Cask Maintenance Facility (CMF); and the development of a concept for site grading and flood control. The analysis also establishes the layout of the surface features (e.g., roads and utilities) that connect all the repository surface areas (North Portal Operations Area, South Portal Development Operations Area, Emplacement Shaft Surface Operations Area, and Development Shaft Surface Operations Area) and locates an area for a potential lag storage facility. Details of South Portal and shaft layouts will be covered in separate design analyses. The objective of this analysis is to provide a suitable level of design for the Viability Assessment (VA). The analysis was revised to incorporate additional material developed since the issuance of Revision 01. This material includes safeguards and security input, utility system input (size and location of fire water tanks and pump houses, potable water and sanitary sewage rates, size of wastewater evaporation pond, size and location of the utility building, size of the bulk fuel storage tank, and size and location of other exterior process equipment), main electrical substation information, redundancy of water supply and storage for the fire support system, and additional information on the storm water retention pond

  13. Mechanical structures with enhanced layout characteristics

    Directory of Open Access Journals (Sweden)

    Yefimenko A. A.

    2016-10-01

    Full Text Available The authors propose solutions for constructing mechanical structures for electronic equipment in terms of plug-in units and subracks, allowing to increase the layout characteristics of electronic modules, sections and desktop devices and increase their functional capacity without changing the architecture of standard mechanical structures. The paper shows effectiveness of the developed solutions. There is a problem of restraining of mass redundancy of mechanical structures for electronic equipment in relation to the weight of the electronic components. On the other hand, the weight is an indicator of structural strength, providing of which is not less important problem. These problems can be solved in different ways, the main of which are the following: a development of new mechanical structures for electronic equipment taking into account the development of the electronic components; b improving layout characteristics of mechanical structures for electronic equipment without significant changes in their architecture. The aim of the study was to research mechanical structures of the first level (plug-in units and modules of the second level of subracks to improve layout characteristics, and to develop methods for the use of connections for surface mounting and for the use of printed circuit boards of smaller dimensions without changing the architecture of the mechanical structures in order to improve layout characteristics. The research allowed the authors to develop the following solutions: 1. The design of plug-in units in which instead of one printed circuit board (PCB may be two, three or more PCBs of smaller dimensions to compensate a decrease in PCB fill factor in time and to increase the functional capacity of electronic modules. 2. Construction of block designs with a bilateral arrangement of plug-in units and the organization of the electrical connections by way of backplanes with electrical connectors for surface mounting, which allows

  14. Methodology of shell structure reinforcement layout optimization

    Science.gov (United States)

    Szafrański, Tomasz; Małachowski, Jerzy; Damaziak, Krzysztof

    2018-01-01

    This paper presents an optimization process of a reinforced shell diffuser intended for a small wind turbine (rated power of 3 kW). The diffuser structure consists of multiple reinforcement and metal skin. This kind of structure is suitable for optimization in terms of selection of reinforcement density, stringers cross sections, sheet thickness, etc. The optimisation approach assumes the reduction of the amount of work to be done between the optimization process and the final product design. The proposed optimization methodology is based on application of a genetic algorithm to generate the optimal reinforcement layout. The obtained results are the basis for modifying the existing Small Wind Turbine (SWT) design.

  15. Hierarchically organized layout for visualization of biochemical pathways.

    Science.gov (United States)

    Tsay, Jyh-Jong; Wu, Bo-Liang; Jeng, Yu-Sen

    2010-01-01

    Many complex pathways are described as hierarchical structures in which a pathway is recursively partitioned into several sub-pathways, and organized hierarchically as a tree. The hierarchical structure provides a natural way to visualize the global structure of a complex pathway. However, none of the previous research on pathway visualization explores the hierarchical structures provided by many complex pathways. In this paper, we aim to develop algorithms that can take advantages of hierarchical structures, and give layouts that explore the global structures as well as local structures of pathways. We present a new hierarchically organized layout algorithm to produce layouts for hierarchically organized pathways. Our algorithm first decomposes a complex pathway into sub-pathway groups along the hierarchical organization, and then partition each sub-pathway group into basic components. It then applies conventional layout algorithms, such as hierarchical layout and force-directed layout, to compute the layout of each basic component. Finally, component layouts are joined to form a final layout of the pathway. Our main contribution is the development of algorithms for decomposing pathways and joining layouts. Experiment shows that our algorithm is able to give comprehensible visualization for pathways with hierarchies, cycles as well as complex structures. It clearly renders the global component structures as well as the local structure in each component. In addition, it runs very fast, and gives better visualization for many examples from previous related research. 2009 Elsevier B.V. All rights reserved.

  16. Performance prediction for silicon photonics integrated circuits with layout-dependent correlated manufacturing variability.

    Science.gov (United States)

    Lu, Zeqin; Jhoja, Jaspreet; Klein, Jackson; Wang, Xu; Liu, Amy; Flueckiger, Jonas; Pond, James; Chrostowski, Lukas

    2017-05-01

    This work develops an enhanced Monte Carlo (MC) simulation methodology to predict the impacts of layout-dependent correlated manufacturing variations on the performance of photonics integrated circuits (PICs). First, to enable such performance prediction, we demonstrate a simple method with sub-nanometer accuracy to characterize photonics manufacturing variations, where the width and height for a fabricated waveguide can be extracted from the spectral response of a racetrack resonator. By measuring the spectral responses for a large number of identical resonators spread over a wafer, statistical results for the variations of waveguide width and height can be obtained. Second, we develop models for the layout-dependent enhanced MC simulation. Our models use netlist extraction to transfer physical layouts into circuit simulators. Spatially correlated physical variations across the PICs are simulated on a discrete grid and are mapped to each circuit component, so that the performance for each component can be updated according to its obtained variations, and therefore, circuit simulations take the correlated variations between components into account. The simulation flow and theoretical models for our layout-dependent enhanced MC simulation are detailed in this paper. As examples, several ring-resonator filter circuits are studied using the developed enhanced MC simulation, and statistical results from the simulations can predict both common-mode and differential-mode variations of the circuit performance.

  17. Josephson shift register design and layout

    International Nuclear Information System (INIS)

    Przybysz, J.X.; Buttyan, J.; Blaugher, R.D.

    1989-01-01

    Integrated circuit chips were designed and fabricated, based on Josephson shift register circuit that simulated operation at 25 GHz using the SPICE program. The 6.25 mm square chip featured a twelve-gate, four-stage shift register fabricated with Nb/AlO/sub x//Nb Josephson junctions with a design value of 2000 A/cm/sup 2/ critical current density. SUPERCOMPACT, a general program for the design of monolithic microwave integrated circuits, was used to model the effects of layout geometry on the uniformity and phase coherence of logic gate bias currents. Gate bias resistors were treated as resistive transmission lines. A layout geometry for the superconductive transmission lines and thin film bias resistors was developed. The original SPICE-designed circuit was modified as a result of these calculations. Modeling indicated that bias current variations could be limited to 3% for all possible logic states of the shift register, and phase coherence of the gates could be maintained to within 2 degrees of 10 Ghz. The fundamental soundness of the circuit design was demonstrated by the proper operation of fabricated shift registers

  18. Evolutionary optimization technique for site layout planning

    KAUST Repository

    El Ansary, Ayman M.

    2014-02-01

    Solving the site layout planning problem is a challenging task. It requires an iterative approach to satisfy design requirements (e.g. energy efficiency, skyview, daylight, roads network, visual privacy, and clear access to favorite views). These design requirements vary from one project to another based on location and client preferences. In the Gulf region, the most important socio-cultural factor is the visual privacy in indoor space. Hence, most of the residential houses in this region are surrounded by high fences to provide privacy, which has a direct impact on other requirements (e.g. daylight and direction to a favorite view). This paper introduces a novel technique to optimally locate and orient residential buildings to satisfy a set of design requirements. The developed technique is based on genetic algorithm which explores the search space for possible solutions. This study considers two dimensional site planning problems. However, it can be extended to solve three dimensional cases. A case study is presented to demonstrate the efficiency of this technique in solving the site layout planning of simple residential dwellings. © 2013 Elsevier B.V. All rights reserved.

  19. Document reconstruction by layout analysis of snippets

    Science.gov (United States)

    Kleber, Florian; Diem, Markus; Sablatnig, Robert

    2010-02-01

    Document analysis is done to analyze entire forms (e.g. intelligent form analysis, table detection) or to describe the layout/structure of a document. Also skew detection of scanned documents is performed to support OCR algorithms that are sensitive to skew. In this paper document analysis is applied to snippets of torn documents to calculate features for the reconstruction. Documents can either be destroyed by the intention to make the printed content unavailable (e.g. tax fraud investigation, business crime) or due to time induced degeneration of ancient documents (e.g. bad storage conditions). Current reconstruction methods for manually torn documents deal with the shape, inpainting and texture synthesis techniques. In this paper the possibility of document analysis techniques of snippets to support the matching algorithm by considering additional features are shown. This implies a rotational analysis, a color analysis and a line detection. As a future work it is planned to extend the feature set with the paper type (blank, checked, lined), the type of the writing (handwritten vs. machine printed) and the text layout of a snippet (text size, line spacing). Preliminary results show that these pre-processing steps can be performed reliably on a real dataset consisting of 690 snippets.

  20. Getting it across : layout issues for kiosk systems

    OpenAIRE

    Borchers, Jan; Deussen, Oliver; Knörzer, Clemens

    1995-01-01

    A clear and appealing screen layout is crucial to the success of on-line kiosk systems, public terminals that are connected to a network. This paper addresses the problem of developing such a layout, and provides several guidelines, drawn from traditional typography and Gestalt psychology as well as from hypertext authoring, and human-computer interaction. To identify how a kiosk system s primary task influences optimal layout, kiosk systems are classified into four basic types. The usability...

  1. Creation of Warehouse Models for Different Layout Designs

    OpenAIRE

    Köhler, Mirko; Lukić, Ivica; Nenadić, Krešimir

    2014-01-01

    Warehouse is one of the most important components in logistics of the supply chain network. Efficiency of warehouse operations is influenced by many different factors. One of the key factors is the racks layout configuration. A warehouse with good racks layout may significantly reduce the cost of warehouse servicing. The objective of this paper is to give a scheme for building warehouses models with one-block and two-block layout for future research in warehouse optimization. An algorithm ...

  2. A New Layout Method for Graphical User Interfaces

    OpenAIRE

    Scoditti , Adriano; Stuerzlinger , Wolfgang

    2010-01-01

    International audience; The layout mechanisms for many GUI toolkits are hard to understand, the associated tools and API's often difficult to use. This work investigates new, easy-to-understand layout mechanisms and evaluates its implementation. We will analyze the requirements for the definition of layouts of a graphical user interface. Part of the issue is that several aspects need to be considered simultaneously while laying-out a component: the alignment with other components as well as i...

  3. Optimization of space-time material layout for 1D wave propagation with varying mass and stiffness parameters

    DEFF Research Database (Denmark)

    Jensen, Jakob Søndergaard

    2010-01-01

    Results are presented for optimal layout of materials in the spatial and temporal domains for a 1D structure subjected to transient wave propagation. A general optimization procedure is outlined including derivation of design sensitivities for the case when the mass density and stiffness vary...

  4. Three-dimensional computer aided design system for plant layout

    International Nuclear Information System (INIS)

    Yoshinaga, Toshiaki; Kiguchi, Takashi; Tokumasu, Shinji; Kumamoto, Kenjiro.

    1986-01-01

    The CAD system for three-dimensional plant layout planning, with which the layout of pipings, cable trays, air conditioning ducts and so on in nuclear power plants can be planned and designed effectively in a short period is reported. This system comprises the automatic routing system by storing the rich experience and know-how of designers in a computer as the knowledge, and deciding the layout automatically following the predetermined sequence by using these, the interactive layout system for reviewing the routing results from higher level and modifying to the optimum layout, the layout evaluation system for synthetically evaluating the layout from the viewpoint of the operability such as checkup and maintenance, and the data base system which enables these effective planning and design. In this report, the total constitution of this system and the technical features and effects of the individual subsystems are outlined. In this CAD system for three-dimensional plant layout planning, knowledge engineering, CAD/CAM, computer graphics and other latest technology were introduced, accordingly by applying this system to plant design, the design can be performed quickly, various case studies can be carried out at planning stage, and systematic and optimum layout planning becomes possible. (Kako, I.)

  5. Layout compliance for triple patterning lithography: an iterative approach

    Science.gov (United States)

    Yu, Bei; Garreton, Gilda; Pan, David Z.

    2014-10-01

    As the semiconductor process further scales down, the industry encounters many lithography-related issues. In the 14nm logic node and beyond, triple patterning lithography (TPL) is one of the most promising techniques for Metal1 layer and possibly Via0 layer. As one of the most challenging problems in TPL, recently layout decomposition efforts have received more attention from both industry and academia. Ideally the decomposer should point out locations in the layout that are not triple patterning decomposable and therefore manual intervention by designers is required. A traditional decomposition flow would be an iterative process, where each iteration consists of an automatic layout decomposition step and manual layout modification task. However, due to the NP-hardness of triple patterning layout decomposition, automatic full chip level layout decomposition requires long computational time and therefore design closure issues continue to linger around in the traditional flow. Challenged by this issue, we present a novel incremental layout decomposition framework to facilitate accelerated iterative decomposition. In the first iteration, our decomposer not only points out all conflicts, but also provides the suggestions to fix them. After the layout modification, instead of solving the full chip problem from scratch, our decomposer can provide a quick solution for a selected portion of layout. We believe this framework is efficient, in terms of performance and designer friendly.

  6. The Offshore Wind Farm Array Cable Layout Problem

    DEFF Research Database (Denmark)

    Bauer, Joanna; Lysgaard, Jens

    2014-01-01

    In an offshore wind farm (OWF), the turbines are connected to a transformer by cable routes that cannot cross each other. Finding the minimum cost array cable layout thus amounts to a vehicle routing problem with the additional constraints that the routes must be embedded in the plane. For this p......In an offshore wind farm (OWF), the turbines are connected to a transformer by cable routes that cannot cross each other. Finding the minimum cost array cable layout thus amounts to a vehicle routing problem with the additional constraints that the routes must be embedded in the plane....... For this problem, both exact and heuristic methods are of interest. We optimize cable layouts for real-world OWFs by a hop-indexed integer programming formulation, and develop a heuristic for computing layouts based on the Clarke and Wright savings heuristic for vehicle routing. Our heuristic computes layouts...... on average only 2% more expensive than the optimal layout. Finally, we present two problem extensions arising from real-world OWF cable layouts, and adapt the integer programming formulation to one of them. The thus obtained optimal layouts are up to 13% cheaper than the actually installed layouts....

  7. Ergonomics influence on control room layout

    International Nuclear Information System (INIS)

    Hartfiel, H.D.

    1984-01-01

    Nowadays, human factors has become an important aspect of the design of work places. Since the control room in a nuclear power plant is a work place, too, its layout is also influenced by ergonomics. With the KWU control room concept for the 1300 MW PWR as an example, we show how assured and applicable ergonomic findings enter into the control room design. On the basis of general design principles for work places, specific methods for control room planning have been developed. By working with these methods a concept that makes it possible to build a man-machine interface able to fulfill the process control tasks with all their underlying conditions has been derived. (author)

  8. Procedural facade variations from a single layout

    KAUST Repository

    Bao, Fan

    2013-02-19

    We introduce a framework to generate many variations of a facade design that look similar to a given facade layout. Starting from an input image, the facade is hierarchically segmented and labeled with a collection of manual and automatic tools. The user can then model constraints that should be maintained in any variation of the input facade design. Subsequently, facade variations are generated for different facade sizes, where multiple variations can be produced for a certain size. Computing such new facade variations has many unique challenges, and we propose a new algorithm based on interleaving heuristic search and quadratic programming. In contrast to most previous work, we focus on the generation of new design variations and not on the automatic analysis of the input\\'s structure. Adding a modeling step with the user in the loop ensures that our results routinely are of high quality. © 2013 ACM.

  9. Procedural facade variations from a single layout

    KAUST Repository

    Bao, Fan; Schwarz, Michael; Wonka, Peter

    2013-01-01

    We introduce a framework to generate many variations of a facade design that look similar to a given facade layout. Starting from an input image, the facade is hierarchically segmented and labeled with a collection of manual and automatic tools. The user can then model constraints that should be maintained in any variation of the input facade design. Subsequently, facade variations are generated for different facade sizes, where multiple variations can be produced for a certain size. Computing such new facade variations has many unique challenges, and we propose a new algorithm based on interleaving heuristic search and quadratic programming. In contrast to most previous work, we focus on the generation of new design variations and not on the automatic analysis of the input's structure. Adding a modeling step with the user in the loop ensures that our results routinely are of high quality. © 2013 ACM.

  10. A bio-inspired, microchanneled hydrogel with controlled spacing of cell adhesion ligands regulates 3D spatial organization of cells and tissue.

    Science.gov (United States)

    Lee, Min Kyung; Rich, Max H; Lee, Jonghwi; Kong, Hyunjoon

    2015-07-01

    Bioactive hydrogels have been extensively studied as a platform for 3D cell culture and tissue regeneration. One of the key desired design parameters is the ability to control spatial organization of biomolecules and cells and subsequent tissue in a 3D matrix. To this end, this study presents a simple but advanced method to spatially organize microchanneled, cell adherent gel blocks and non-adherent ones in a single construct. This hydrogel system was prepared by first fabricating a bimodal hydrogel in which the microscale, alginate gel blocks modified with cell adhesion peptides containing Arg-Gly-Asp sequence (RGD peptides), and those free of RGD peptides, were alternatingly presented. Then, anisotropically aligned microchannels were introduced by uniaxial freeze-drying of the bimodal hydrogel. The resulting gel system could drive bone marrow stromal cells to adhere to and differentiate into neuron and glial cells exclusively in microchannels of the alginate gel blocks modified with RGD peptides. Separately, the bimodal gel loaded with microparticles releasing vascular endothelial growth factor stimulated vascular growth solely into microchannels of the RGD-alginate gel blocks in vivo. These results were not attained by the bimodal hydrogel fabricated to present randomly oriented micropores. Overall, the bimodal gel system could regulate spatial organization of nerve-like tissue or blood vessels at sub-micrometer length scale. We believe that the hydrogel assembly demonstrated in this study will be highly useful in developing a better understanding of diverse cellular behaviors in 3D tissue and further improve quality of a wide array of engineered tissues. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Underground design Laxemar, Layout D2

    Energy Technology Data Exchange (ETDEWEB)

    2009-11-15

    Laxemar candidate area is located in the province of Smaaland, some 320 km south of Stockholm. The area is located close to the shoreline of the Baltic Sea and is within the municipality of Oskarshamn, and immediately west of the Oskarshamn nuclear power plant and the Central interim storage facility for spent fuel (Clab). The easternmost part (Simpevarp subarea) includes the Simpevarp peninsula, which hosts the power plants and the Clab facility. The island of Aespoe, containing the Aespoe Hard Rock Laboratory is located some three kilometres northeast of the central parts of Laxemar. The Laxemar subarea covers some 12.5 km2, compared with the Simepvarp subarea, which is approximately 6.6 km2. The Laxemar candidate area has been investigated in stages, referred to as the initial site investigations (ISI) and the complete site investigations (CSI). These investigations commenced in 2002 and were completed in 2008. During the site investigations, several studies and design steps (D0, D1 and D2) were carried out to ensure that sufficient space was available for the 6,000-canister layout within the target volume at a depth of approximately 500 m. The findings from design Step D2 for the underground facilities including the access ramp, shafts, rock caverns in a Central Area, transport tunnels, and deposition tunnels and deposition holes are contained in this report. The layout for these underground excavations at the deposition horizon requires an area of 5.7 km2, and the total rock volume to be excavated is 3,008 x 103 m3 using a total tunnel length of approximately 115 km. The behaviour of the underground openings associated with this layout is expected to be similar to the behaviour of other underground openings in the Scandinavian shield at similar depths. The dominant mode of instability is expected to be structurally controlled wedge failure. Stability of the openings will be achieved with traditional underground rock support and by orienting the openings

  12. Optimal layout of radiological environment monitoring based on TOPSIS method

    International Nuclear Information System (INIS)

    Li Sufen; Zhou Chunlin

    2006-01-01

    TOPSIS is a method for multi-objective-decision-making, which can be applied to comprehensive assessment of environmental quality. This paper adopts it to get the optimal layout of radiological environment monitoring, it is proved that this method is a correct, simple and convenient, practical one, and beneficial to supervision departments to scientifically and reasonably layout Radiological Environment monitoring sites. (authors)

  13. Layout and cabling considerations for a large communications antenna array

    Science.gov (United States)

    Logan, R. T., Jr.

    1993-01-01

    Layout considerations for a large deep space communications antenna array are discussed. A fractal geometry for the antenna layout is described that provides optimal packing of antenna elements, efficient cable routing, and logical division of the array into identical sub-arrays.

  14. Selecting a pharmacy layout design using a weighted scoring system.

    Science.gov (United States)

    McDowell, Alissa L; Huang, Yu-Li

    2012-05-01

    A weighted scoring system was used to select a pharmacy layout redesign. Facilities layout design techniques were applied at a local hospital pharmacy using a step-by-step design process. The process involved observing and analyzing the current situation, observing the current available space, completing activity flow charts of the pharmacy processes, completing communication and material relationship charts to detail which areas in the pharmacy were related to one another and how they were related, researching applications in other pharmacies or in scholarly works that could be beneficial, numerically defining space requirements for areas within the pharmacy, measuring the available space within the pharmacy, developing a set of preliminary designs, and modifying preliminary designs so they were all acceptable to the pharmacy staff. To select a final layout that could be implemented in the pharmacy, those layouts were compared via a weighted scoring system. The weighted aspect further allowed additional emphasis on categories based on their effect on pharmacy performance. The results produced a beneficial layout design as determined through simulated models of the pharmacy operation that more effectively allocated and strategically located space to improve transportation distances and materials handling, employee utilization, and ergonomics. Facilities layout designs for a hospital pharmacy were evaluated using a weighted scoring system to identify a design that was superior to both the current layout and alternative layouts in terms of feasibility, cost, patient safety, employee safety, flexibility, robustness, transportation distance, employee utilization, objective adherence, maintainability, usability, and environmental impact.

  15. Optimization of machining fixture layout for tolerance requirements ...

    African Journals Online (AJOL)

    Dimensional accuracy of workpart under machining is strongly influenced by the layout of the fixturing elements like locators and clamps. Setup or geometrical errors in locators result in overall machining error of the feature under consideration. Therefore it is necessary to ensure that the layout is optimized for the desired ...

  16. Student Perceptions of Textbook Layout and Learnability in Private Schools

    Science.gov (United States)

    Hoshangabadwala, Alefiyah

    2015-01-01

    This research is an exploratory study that investigates students' perceptions pertinent to textbook layout and organization and their evaluation of the textbook ease of learning. The objective is to find out whether the layout dynamics of school textbooks make any difference in students' interest in studying or subject understanding. 73 students…

  17. Layout Of Antennas And Cables In A Large Array

    Science.gov (United States)

    Logan, Ronald T., Jr.

    1995-01-01

    Layout devised to minimize total land area occupied by large phased array of antennas and to minimize total length of cables in array. In original intended application, array expanded version of array of paraboloidal-dish microwave communication antennas of Deep Space Network. Layout also advantageous for other phased arrays of antennas and antenna elements, including notably printed-circuit microwave antenna arrays.

  18. DSS 13 phase 2 pedestal room microwave layout

    Science.gov (United States)

    Cwik, T.; Chen, J. C.

    1991-01-01

    The design and predicted performance is described of the microwave layout for three band operation of the beam waveguide antenna Deep Space Station 13. Three pedestal room microwave candidate layout designs were produced for simultaneous X/S and X/Ka band operation. One of the three designs was chosen based on given constraints, and for this design the microwave performance was estimated.

  19. Layout and flow of dermatology clinics: principles from operations management.

    Science.gov (United States)

    Wang, Jordan V

    2018-04-15

    Dermatology is a medical specialty that experiences high patient demand and long patient wait times. Dermatology clinics should look for ways to improve efficiency through the incorporation of principles from operations management. Addressing the layout and flow of a clinic can lead to operational efficiency. An ideal layout may lead to increased patient volume, satisfaction, and retention.

  20. Scalable force directed graph layout algorithms using fast multipole methods

    KAUST Repository

    Yunis, Enas Abdulrahman; Yokota, Rio; Ahmadia, Aron

    2012-01-01

    We present an extension to ExaFMM, a Fast Multipole Method library, as a generalized approach for fast and scalable execution of the Force-Directed Graph Layout algorithm. The Force-Directed Graph Layout algorithm is a physics-based approach

  1. A linear time layout algorithm for business process models

    NARCIS (Netherlands)

    Gschwind, T.; Pinggera, J.; Zugal, S.; Reijers, H.A.; Weber, B.

    2014-01-01

    The layout of a business process model influences how easily it can beunderstood. Existing layout features in process modeling tools often rely on graph representations, but do not take the specific properties of business process models into account. In this paper, we propose an algorithm that is

  2. Simulation Modeling of a Facility Layout in Operations Management Classes

    Science.gov (United States)

    Yazici, Hulya Julie

    2006-01-01

    Teaching quantitative courses can be challenging. Similarly, layout modeling and lean production concepts can be difficult to grasp in an introductory OM (operations management) class. This article describes a simulation model developed in PROMODEL to facilitate the learning of layout modeling and lean manufacturing. Simulation allows for the…

  3. Agriculture Education. Elements of Farm and Building Layout.

    Science.gov (United States)

    Stuttgart Public Schools, AR.

    This curriculum guide is designed for group instruction of secondary agricultural education students enrolled in one or two semester-long courses in elements of farm and building layout. The guide presents units of study in the following areas: (1) sketching and drawing equipment, (2) gothic lettering, (3) layout of a standard sheet, (4) job…

  4. Developing an Integrated Design Strategy for Chip Layout Optimization

    NARCIS (Netherlands)

    Wits, Wessel Willems; Jauregui Becker, Juan Manuel; van Vliet, Frank Edward; te Riele, G.J.

    2011-01-01

    This paper presents an integrated design strategy for chip layout optimization. The strategy couples both electric and thermal aspects during the conceptual design phase to improve chip performances; thermal management being one of the major topics. The layout of the chip circuitry is optimized

  5. On the impact of layout quality to understanding UML diagrams

    DEFF Research Database (Denmark)

    Störrle, Harald

    2011-01-01

    previous research considered them in isolation only. In this paper, we report the results of a series of controlled experiments using compound layouts on requirements analysis models. With very high significance, we find a notable impact of the layout quality measured by different aspects of cognitive load....

  6. FUZZY NEURAL NETWORK FOR OBJECT IDENTIFICATION ON INTEGRATED CIRCUIT LAYOUTS

    Directory of Open Access Journals (Sweden)

    A. A. Doudkin

    2015-01-01

    Full Text Available Fuzzy neural network model based on neocognitron is proposed to identify layout objects on images of topological layers of integrated circuits. Testing of the model on images of real chip layouts was showed a highеr degree of identification of the proposed neural network in comparison to base neocognitron.

  7. Issues in Text Design and Layout for Computer Based Communications.

    Science.gov (United States)

    Andresen, Lee W.

    1991-01-01

    Discussion of computer-based communications (CBC) focuses on issues involved with screen design and layout for electronic text, based on experiences with electronic messaging, conferencing, and publishing within the Australian Open Learning Information Network (AOLIN). Recommendations for research on design and layout for printed text are also…

  8. Target aligned heliostat field layout for non-flat terrrain

    CSIR Research Space (South Africa)

    Buck, R

    2012-05-01

    Full Text Available The layout for a solar tower test facility for CSIR, Pretoria, is described. The solar tower system is designed for 400kWth receiver outlet power. The heliostat field layout takes into account both the real (non-flat) topography of the terrain...

  9. Layout of the LER [Low Energy Ring] Arc

    International Nuclear Information System (INIS)

    Hutton, A.

    1990-01-01

    We have recently been trying to accumulate all of the information necessary to decide on the layout of the regular curved arcs of the Low Energy Ring (LER) and there have been several ABC Notes published on different aspects of the problem. This note will describe the layout that has been derived from these considerations

  10. Planning, layout and infrastructure of modern coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Haarmann, K R

    1978-02-01

    When designing layout and infrastructure of new coal mines, the principles of planning play a decisive role. Apart from exploration, ventilation, transport, dirt haulage and product haulage, material transport is very important. Illustrated by three examples, modern layout and infrastructure design is presented.

  11. Multipurpose layout drawing of metalware of bridge crane load trolley

    Directory of Open Access Journals (Sweden)

    Goncharov K.A.

    2017-03-01

    Full Text Available Multipurpose layout drawing of metalware of bridge crane load trolley is proposed. The numerical analysis of proposed layout drawing is conducted using the example of bridge crane load trolley with capacity of 20 t. This analysis is carried out using the finite element method.

  12. Application of plurigaussian simulation to delineate the layout of alteration domains in Sungun copper deposit

    Science.gov (United States)

    Talebi, Hassan; Asghari, Omid; Emery, Xavier

    2013-12-01

    An accurate estimation of mineral grades in ore deposits with heterogeneous spatial variations requires defining geological domains that differentiate the types of mineralogy, alteration and lithology. Deterministic models define the layout of the domains based on the interpretation of the drill holes and do not take into account the uncertainty in areas with fewer data. Plurigaussian simulation (PGS) can be an alternative to generate multiple numerical models of the ore body, with the aim of assessing the uncertainty in the domain boundaries and improving the geological controls in the characterization of quantitative attributes. This study addresses the application of PGS to Sungun porphyry copper deposit (Iran), in order to simulate the layout of four hypogene alteration zones: potassic, phyllic, propylitic and argillic. The aim of this study is to construct numerical models in which the alteration structures reflect the evolution observed in the geology.

  13. Optimal Control Surface Layout for an Aeroservoelastic Wingbox

    Science.gov (United States)

    Stanford, Bret K.

    2017-01-01

    This paper demonstrates a technique for locating the optimal control surface layout of an aeroservoelastic Common Research Model wingbox, in the context of maneuver load alleviation and active utter suppression. The combinatorial actuator layout design is solved using ideas borrowed from topology optimization, where the effectiveness of a given control surface is tied to a layout design variable, which varies from zero (the actuator is removed) to one (the actuator is retained). These layout design variables are optimized concurrently with a large number of structural wingbox sizing variables and control surface actuation variables, in order to minimize the sum of structural weight and actuator weight. Results are presented that demonstrate interdependencies between structural sizing patterns and optimal control surface layouts, for both static and dynamic aeroelastic physics.

  14. Topology-optimized metasurfaces: impact of initial geometric layout.

    Science.gov (United States)

    Yang, Jianji; Fan, Jonathan A

    2017-08-15

    Topology optimization is a powerful iterative inverse design technique in metasurface engineering and can transform an initial layout into a high-performance device. With this method, devices are optimized within a local design phase space, making the identification of suitable initial geometries essential. In this Letter, we examine the impact of initial geometric layout on the performance of large-angle (75 deg) topology-optimized metagrating deflectors. We find that when conventional metasurface designs based on dielectric nanoposts are used as initial layouts for topology optimization, the final devices have efficiencies around 65%. In contrast, when random initial layouts are used, the final devices have ultra-high efficiencies that can reach 94%. Our numerical experiments suggest that device topologies based on conventional metasurface designs may not be suitable to produce ultra-high-efficiency, large-angle metasurfaces. Rather, initial geometric layouts with non-trivial topologies and shapes are required.

  15. A Derivatization and Validation Strategy for Determining the Spatial Localization of Endogenous Amine Metabolites in Tissues using MALDI Imaging Mass Spectrometry

    Science.gov (United States)

    Manier, M. Lisa; Spraggins, Jeffrey M.; Reyzer, Michelle L.; Norris, Jeremy L.; Caprioli, Richard M.

    2014-01-01

    Imaging mass spectrometry (IMS) studies increasingly focus on endogenous small molecular weight metabolites and consequently bring special analytical challenges. Since analytical tissue blanks do not exist for endogenous metabolites, careful consideration must be given to confirm molecular identity. Here we present approaches for the improvement in detection of endogenous amine metabolites such as amino acids and neurotransmitters in tissues through chemical derivatization and matrix-assisted laser desorption/ionization (MALDI) IMS. Chemical derivatization with 4-hydroxy-3-methoxycinnamaldehyde (CA) was used to improve sensitivity and specificity. CA was applied to the tissue via MALDI sample targets precoated with a mixture of derivatization reagent and ferulic acid (FA) as a MALDI matrix. Spatial distributions of chemically derivatized endogenous metabolites in tissue were determined by high-mass resolution and MSn imaging mass spectrometry. We highlight an analytical strategy for metabolite validation whereby tissue extracts are analyzed by high-performance liquid chromatography (HPLC)-MS/MS to unambiguously identify metabolites and distinguish them from isobaric compounds. PMID:25044893

  16. Size and spatial orientation of uterine tissue transplants on the peritoneum crucially determine the growth and cyst formation of endometriosis-like lesions in mice.

    Science.gov (United States)

    Körbel, Christina; Menger, Michael D; Laschke, Matthias W

    2010-10-01

    In many studies in rodents, intraperitoneal endometriosis-like lesions are surgically induced by syngeneic or autologous transplantation of uterine tissue samples, which are sutured to the abdominal wall. However, until now the surgical techniques have not been standardized, and we address this issue here. Uterine tissue samples were transplanted to the peritoneum of C57BL/6 mice (four study groups, n = 7 each). Using non-invasive high-resolution ultrasound imaging over a period of 4 weeks, we analyzed growth characteristics and cyst formation of the endometriosis-like lesions which developed, in relation to mode of transplantation (syngeneic versus autologous), type of tissue fixed adjacent to the peritoneum (endometrium versus perimetrium), and size of tissue transplanted (2 versus 3 mm). Immunohistochemical analysis was also performed. When the perimetrium, with underlying myometrium, was sutured next to the host peritoneum the endometriosis-like lesions which developed exhibited a higher growth rate (Pendometriosis-like lesions. Our study demonstrates that size and spatial orientation of peritoneally fixed uterine tissue samples crucially determine growth and cyst formation of endometriotic lesions in mice. These findings should improve the standardization and reliability of future studies, performed in the frequently used mouse model of surgically induced endometriosis.

  17. ITER plant layout and site services

    International Nuclear Information System (INIS)

    Chuyanov, V.A.

    2000-01-01

    The ITER site has not yet been determined. Nevertheless, to develop a construction plan and a cost estimate, it is necessary to have a detailed layout of the buildings, structures and outdoor equipment integrated with the balance of plant service systems prototypical of large fusion power plants. These services include electrical power for magnet feeds and plasma heating systems, cryogenic and conventional cooling systems, compressed air, gas supplies, demineralized water, steam and drainage. Nuclear grade facilities are provided to handle tritium fuel and activated waste, as well as to prevent radiation exposure of workers and the public. To prevent interference between services of different types and for efficient arrangement of buildings, structures and equipment within the site area, a plan was developed which segregated different classes of services to four quadrants surrounding the tokamak building, placed at the approximate geographical centre of the site. The locations of the buildings on the generic site were selected to meet all design requirements at minimum total project cost. A similar approach was used to determine the locations of services above, at and below grade. The generic site plan can be adapted to the site selected for ITER without significant changes to the buildings or equipment. Some rearrangements may be required by site topography, resulting primarily in changes to the length of services that link the buildings and equipment. (author)

  18. A generic algorithm for layout of biological networks.

    Science.gov (United States)

    Schreiber, Falk; Dwyer, Tim; Marriott, Kim; Wybrow, Michael

    2009-11-12

    Biological networks are widely used to represent processes in biological systems and to capture interactions and dependencies between biological entities. Their size and complexity is steadily increasing due to the ongoing growth of knowledge in the life sciences. To aid understanding of biological networks several algorithms for laying out and graphically representing networks and network analysis results have been developed. However, current algorithms are specialized to particular layout styles and therefore different algorithms are required for each kind of network and/or style of layout. This increases implementation effort and means that new algorithms must be developed for new layout styles. Furthermore, additional effort is necessary to compose different layout conventions in the same diagram. Also the user cannot usually customize the placement of nodes to tailor the layout to their particular need or task and there is little support for interactive network exploration. We present a novel algorithm to visualize different biological networks and network analysis results in meaningful ways depending on network types and analysis outcome. Our method is based on constrained graph layout and we demonstrate how it can handle the drawing conventions used in biological networks. The presented algorithm offers the ability to produce many of the fundamental popular drawing styles while allowing the exibility of constraints to further tailor these layouts.

  19. Fast grid layout algorithm for biological networks with sweep calculation.

    Science.gov (United States)

    Kojima, Kaname; Nagasaki, Masao; Miyano, Satoru

    2008-06-15

    Properly drawn biological networks are of great help in the comprehension of their characteristics. The quality of the layouts for retrieved biological networks is critical for pathway databases. However, since it is unrealistic to manually draw biological networks for every retrieval, automatic drawing algorithms are essential. Grid layout algorithms handle various biological properties such as aligning vertices having the same attributes and complicated positional constraints according to their subcellular localizations; thus, they succeed in providing biologically comprehensible layouts. However, existing grid layout algorithms are not suitable for real-time drawing, which is one of requisites for applications to pathway databases, due to their high-computational cost. In addition, they do not consider edge directions and their resulting layouts lack traceability for biochemical reactions and gene regulations, which are the most important features in biological networks. We devise a new calculation method termed sweep calculation and reduce the time complexity of the current grid layout algorithms through its encoding and decoding processes. We conduct practical experiments by using 95 pathway models of various sizes from TRANSPATH and show that our new grid layout algorithm is much faster than existing grid layout algorithms. For the cost function, we introduce a new component that penalizes undesirable edge directions to avoid the lack of traceability in pathways due to the differences in direction between in-edges and out-edges of each vertex. Java implementations of our layout algorithms are available in Cell Illustrator. masao@ims.u-tokyo.ac.jp Supplementary data are available at Bioinformatics online.

  20. DISTRIBUTION OF BOREHOLES IN RESIDENTIAL LAYOUTS AND ...

    African Journals Online (AJOL)

    IPPIS NAU

    2017-07-01

    Jul 1, 2017 ... This spatial spread makes a good demand on urban amenities ... a view to determining the level of their accessibility to consumers ... The choice of the ..... has forced the affected consumers to spend unbearable amount of ...

  1. Neighboring Structure Visualization on a Grid-based Layout.

    Science.gov (United States)

    Marcou, G; Horvath, D; Varnek, A

    2017-10-01

    Here, we describe an algorithm to visualize chemical structures on a grid-based layout in such a way that similar structures are neighboring. It is based on structure reordering with the help of the Hilbert Schmidt Independence Criterion, representing an empirical estimate of the Hilbert-Schmidt norm of the cross-covariance operator. The method can be applied to any layout of bi- or three-dimensional shape. The approach is demonstrated on a set of dopamine D5 ligands visualized on squared, disk and spherical layouts. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Optimization of offshore wind farm layout in restricted zones

    DEFF Research Database (Denmark)

    Hou, Peng; Hu, Weihao; Chen, Cong

    2016-01-01

    In this research, an optimization method for offshore wind farm layout design is proposed. With the purpose of maximizing the energy production of the wind farm, the wind turbine (WT) positions are optimized. Due to the limitations of seabed conditions, marine traffic limitations or shipwrecks, etc...... with multiple adaptive methods (PSO-MAM) is adopted. The simulation results indicate that the proposed method can find a layout which outperforms a baseline layout of a reference wind farm (RWF) by increasing the energy yield by 3.84%....

  3. Determination of Optimal Imaging Mode for Ultrasonographic Detection of Subdermal Contraceptive Rods: Comparison of Spatial Compound, Conventional, and Tissue Harmonic Imaging Methods

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sung Jin; Seo, Kyung; Song, Ho Taek; Park, Ah Young; Kim, Yaena; Yoon, Choon Sik [Gangnam Severance Hospital, Yonsei University College of Medicine, Seoul (Korea, Republic of); Suh, Jin Suck; Kim, Ah Hyun [Dept. of Radiology and Research Institute of Radiological Science, Severance Hospital, Yonsei University College of Medicine, Seoul (Korea, Republic of); Ryu, Jeong Ah [Dept. of Radiology, Guri Hospital, Hanyang University College of Medicine, Guri (Korea, Republic of); Park, Jeong Seon [Dept. of Radiology, Hanyang University Hospital, Hanyang University College of Medicine, Seoul (Korea, Republic of)

    2012-09-15

    To determine which mode of ultrasonography (US), among the conventional, spatial compound, and tissue-harmonic methods, exhibits the best performance for the detection of Implanon with respect to generation of posterior acoustic shadowing (PAS). A total of 21 patients, referred for localization of impalpable Implanon, underwent US, using the three modes with default settings (i.e., wide focal zone). Representative transverse images of the rods, according to each mode for all patients, were obtained. The resulting 63 images were reviewed by four observers. The observers provided a confidence score for the presence of PAS, using a five-point scale ranging from 1 (definitely absent) to 5 (definitely present), with scores of 4 or 5 for PAS being considered as detection. The average scores of PAS, obtained from the three different modes for each observer, were compared using one-way repeated measure ANOVA. The detection rates were compared using a weighted least square method. Statistically, the tissue harmonic mode was significantly superior to the other two modes, when comparing the average scores of PAS for all observers (p < 0.00-1). The detection rate was also highest for the tissue harmonic mode (p < 0.001). Tissue harmonic mode in US appears to be the most suitable in detecting subdermal contraceptive implant rods.

  4. Determination of Optimal Imaging Mode for Ultrasonographic Detection of Subdermal Contraceptive Rods: Comparison of Spatial Compound, Conventional, and Tissue Harmonic Imaging Methods

    International Nuclear Information System (INIS)

    Kim, Sung Jin; Seo, Kyung; Song, Ho Taek; Park, Ah Young; Kim, Yaena; Yoon, Choon Sik; Suh, Jin Suck; Kim, Ah Hyun; Ryu, Jeong Ah; Park, Jeong Seon

    2012-01-01

    To determine which mode of ultrasonography (US), among the conventional, spatial compound, and tissue-harmonic methods, exhibits the best performance for the detection of Implanon with respect to generation of posterior acoustic shadowing (PAS). A total of 21 patients, referred for localization of impalpable Implanon, underwent US, using the three modes with default settings (i.e., wide focal zone). Representative transverse images of the rods, according to each mode for all patients, were obtained. The resulting 63 images were reviewed by four observers. The observers provided a confidence score for the presence of PAS, using a five-point scale ranging from 1 (definitely absent) to 5 (definitely present), with scores of 4 or 5 for PAS being considered as detection. The average scores of PAS, obtained from the three different modes for each observer, were compared using one-way repeated measure ANOVA. The detection rates were compared using a weighted least square method. Statistically, the tissue harmonic mode was significantly superior to the other two modes, when comparing the average scores of PAS for all observers (p < 0.00-1). The detection rate was also highest for the tissue harmonic mode (p < 0.001). Tissue harmonic mode in US appears to be the most suitable in detecting subdermal contraceptive implant rods.

  5. Spatial changes in acid secretion from isolated stomach tissue using a pH-histamine sensing microarray.

    Science.gov (United States)

    Bitziou, Eleni; O'Hare, Danny; Patel, Bhavik Anil

    2010-03-01

    The acid secretion mechanism can be studied by measuring a series of metabolic markers and neurotransmitters from in vitro isolated tissue. A microelectrode array was used to monitor proton concentration and histamine levels from isolated guinea pig stomach tissue. The device was partially modified using iridium oxide to form a series of pH sensors, whereas unmodified gold microelectrodes were used to measure the level of histamine in the gut. Real-time measurements in the presence of the H2-receptor antagonist ranitidine produced significant decreases in the overall Delta pH response, as expected. Also, a significant variation in the Delta pH response in between pH sensors was observed in the presence of pharmacological treatment due to structural features of the tissue. No significant differences in Delta i(H) were detected in the presence of ranitidine as expected. More significantly, clear variations in Delta pH responses between animals in control conditions and those in the presence of ranitidine was observed highlighting possible variation in parietal cell density and/or variations in tissue activity. These results identify great possibilities in applying these multi-sensing devices as a long-term stable personalised diagnostic tool for pharmacological screening and disease status.

  6. An impedance method for spatial sensing of 3D cell constructs – towards applications in tissue engineering

    DEFF Research Database (Denmark)

    Canali, Chiara; Mazzoni, Chiara; Larsen, Layla Bashir

    2015-01-01

    ) cells were encapsulated in gelatin to form artificial 3D cell constructs and detected when placed in different positions inside large gelatin scaffolds. Taken together, these results open new perspectives for impedance-based sensing technologies for non-invasive monitoring in tissue engineering...

  7. Re-emergence of Indigeneity in transformed Layouts in Urban Public Housing in Nigeria

    Directory of Open Access Journals (Sweden)

    Abubakar Danladi Isah

    2016-01-01

    Full Text Available In contrast to the one whole homogenous configuration provided by developers that has often proved ineffective overtime, transformed public housing units are widespread in developing cities. Though transformation is a natural phenomenon of inhabitation, its various levels and degree can have implicit values. In recent times in Nigeria, heterogeneous spatial patterns of transformed houses in public housing estates has given empirical evidence of essentially inevitable reflection of culture sensitivity as hypothesized by previous studies. That hints that the mainstream sustainable values were probably ignored during design process. This study attempted to connect that possible missing link. To achieve that aim, it developed two objectives. First, is to identify core values behind space layouts in the mainstream. Then, to examine how they exist in the transformed layout as reflected at communal origins. It investigated on 42 transformed units in selected urban Public housings neighborhoods via a stratified conditional sampling conducted in five states of Nigeria. Qualitative methods were adopted for data analysis. After identifying the core ethnic groups in the region, their social indicators with regards to space use were determined through ethnographic principles. These indicators were then operationally defined, and used as a tool to examine users’ motivations in the transformation process in urban context. Spatial pattern analysis, by using gamma delineation, revealed the social content in the transformations after comparing initial design and the transformed spatial configurations. The outcome signified the mainstream cultural values in the transformation process hence in Public housing design. The convergence of mainstream values into urban transformed layouts suggested that they cannot be ignored during design process. The outcome of this research might be useful in designing sustainable public housings in culture sensitive environments

  8. Learning Layouts for Single-Page Graphic Designs.

    Science.gov (United States)

    O'Donovan, Peter; Agarwala, Aseem; Hertzmann, Aaron

    2014-08-01

    This paper presents an approach for automatically creating graphic design layouts using a new energy-based model derived from design principles. The model includes several new algorithms for analyzing graphic designs, including the prediction of perceived importance, alignment detection, and hierarchical segmentation. Given the model, we use optimization to synthesize new layouts for a variety of single-page graphic designs. Model parameters are learned with Nonlinear Inverse Optimization (NIO) from a small number of example layouts. To demonstrate our approach, we show results for applications including generating design layouts in various styles, retargeting designs to new sizes, and improving existing designs. We also compare our automatic results with designs created using crowdsourcing and show that our approach performs slightly better than novice designers.

  9. Optimal Material Layout - Applied on Reinforced Concrete Slabs

    DEFF Research Database (Denmark)

    Dollerup, Niels; Jepsen, Michael S.; Damkilde, Lars

    2015-01-01

    This paper introduces a general, finite-element-based optimisation tool for improving the material layout of concrete structures. The application presented is general and exemplified by material optimisation of reinforced concrete slabs. By utilising the optimisation tool, it is possible to deter......This paper introduces a general, finite-element-based optimisation tool for improving the material layout of concrete structures. The application presented is general and exemplified by material optimisation of reinforced concrete slabs. By utilising the optimisation tool, it is possible...... to determine the optimal material layout of a slab in the ultimate load state, based on simple inputs such as outer geometry, boundary conditions, multiple load cases and design domains. The material layout of the optimal design can either be fully orthotropic or isotropic, or a combination with a predefined...

  10. Supporting the design of office layout meeting ergonomics requirements.

    Science.gov (United States)

    Margaritis, Spyros; Marmaras, Nicolas

    2007-11-01

    This paper proposes a method and an information technology tool aiming to support the ergonomics layout design of individual workstations in a given space (building). The proposed method shares common ideas with previous generic methods for office layout. However, it goes a step forward and focuses on the cognitive tasks which have to be carried out by the designer or the design team trying to alleviate them. This is achieved in two ways: (i) by decomposing the layout design problem to six main stages, during which only a limited number of variables and requirements are considered and (ii) by converting the ergonomics requirements to functional design guidelines. The information technology tool (ErgoOffice 0.1) automates certain phases of the layout design process, and supports the design team either by its editing and graphical facilities or by providing adequate memory support.

  11. Spatial and temporal trends of selected trace elements in liver tissue from polar bears (Ursus maritimus) from Alaska, Canada and Greenland

    Science.gov (United States)

    Routti, H.; Letcher, R.J.; Born, E.W.; Branigan, M.; Dietz, R.; Evans, T.J.; Fisk, A.T.; Peacock, E.; Sonne, C.

    2011-01-01

    Spatial trends and comparative changes in time of selected trace elements were studied in liver tissue from polar bears from ten different subpopulation locations in Alaska, Canadian Arctic and East Greenland. For nine of the trace elements (As, Cd, Cu, Hg, Mn, Pb, Rb, Se and Zn) spatial trends were investigated in 136 specimens sampled during 2005-2008 from bears from these ten subpopulations. Concentrations of Hg, Se and As were highest in the (northern and southern) Beaufort Sea area and lowest in (western and southern) Hudson Bay area and Chukchi/Bering Sea. In contrast, concentrations of Cd showed an increasing trend from east to west. Minor or no spatial trends were observed for Cu, Mn, Rb and Zn. Spatial trends were in agreement with previous studies, possibly explained by natural phenomena. To assess temporal changes of Cd, Hg, Se and Zn concentrations during the last decades, we compared our results to previously published data. These time comparisons suggested recent Hg increase in East Greenland polar bears. This may be related to Hg emissions and/or climate-induced changes in Hg cycles or changes in the polar bear food web related to global warming. Also, Hg:Se molar ratio has increased in East Greenland polar bears, which suggests there may be an increased risk for Hg 2+-mediated toxicity. Since the underlying reasons for spatial trends or changes in time of trace elements in the Arctic are still largely unknown, future studies should focus on the role of changing climate and trace metal emissions on geographical and temporal trends of trace elements. ?? 2011 The Royal Society of Chemistry.

  12. Spatial and temporal trends of selected trace elements in liver tissue from polar bears (Ursus maritimus) from Alaska, Canada and Greenland.

    Science.gov (United States)

    Routti, Heli; Letcher, Robert J; Born, Erik W; Branigan, Marsha; Dietz, Rune; Evans, Thomas J; Fisk, Aaron T; Peacock, Elizabeth; Sonne, Christian

    2011-08-01

    Spatial trends and comparative changes in time of selected trace elements were studied in liver tissue from polar bears from ten different subpopulation locations in Alaska, Canadian Arctic and East Greenland. For nine of the trace elements (As, Cd, Cu, Hg, Mn, Pb, Rb, Se and Zn) spatial trends were investigated in 136 specimens sampled during 2005-2008 from bears from these ten subpopulations. Concentrations of Hg, Se and As were highest in the (northern and southern) Beaufort Sea area and lowest in (western and southern) Hudson Bay area and Chukchi/Bering Sea. In contrast, concentrations of Cd showed an increasing trend from east to west. Minor or no spatial trends were observed for Cu, Mn, Rb and Zn. Spatial trends were in agreement with previous studies, possibly explained by natural phenomena. To assess temporal changes of Cd, Hg, Se and Zn concentrations during the last decades, we compared our results to previously published data. These time comparisons suggested recent Hg increase in East Greenland polar bears. This may be related to Hg emissions and/or climate-induced changes in Hg cycles or changes in the polar bear food web related to global warming. Also, Hg:Se molar ratio has increased in East Greenland polar bears, which suggests there may be an increased risk for Hg(2+)-mediated toxicity. Since the underlying reasons for spatial trends or changes in time of trace elements in the Arctic are still largely unknown, future studies should focus on the role of changing climate and trace metal emissions on geographical and temporal trends of trace elements.

  13. KBS-3H layout adaptation 2007 for the Olkiluoto site

    International Nuclear Information System (INIS)

    Johansson, Erik; Hagros, Annika; Autio, Jorma; Kirkkomaeki, Timo

    2008-05-01

    As part of the KBS-3H design an Olkiluoto-specific layout of a KBS-3H repository has been produced based on the latest Olkiluoto data and the bedrock model. One of the main goals of this work was to support the evaluation of the feasibility of the one layer KBS-3H concept and to compare the layouts based on the KBS-3H and KBS-3V disposal concepts. The layout presented in this work can be considered only preliminary and involves a number of uncertainties. The percentage of unusable host rock was assumed to be 25% in this work but can change due to the further design of the different components of the KBS-3H disposal system and further development of the host rock criteria. The layout is also significantly affected by the layout-determining fracture zones. In this work 11 major (highly transmissive) fracture zones interpreted to intersect the -420 m level were considered deterministically. The KBS-3H layout requires a larger area than the KBS-3V repository and takes up most of the available area between the major fracture zones HZ20 and HZ21. This is mainly due to the long drift sections occupied by the compartment plugs (30 m) and the bentonite blocks in the blank zones (10 m), which reduces the usability of the host rock and results in larger canister spacings than in the KBS-3V concept, where the positioning of the deposition holes is very flexible and narrow zones with a moderate transmissivity usually have only a minor effect on the locations of the canisters. According to the results, there is enough bedrock in the current investigation area at central Olkiluoto for KBS-3H layout in one layer. However the layout takes up nearly all of the potential bedrock resource and therefore the result is quite sensitive to possible changes in the design bases

  14. Site selection and general layout of heap leaching uranium mill

    International Nuclear Information System (INIS)

    Zhang Chunmao; Rongfeng

    2011-01-01

    The site selection and general layout of uranium mill is an important work in the design and consultation stage of uranium mining and metallurgy's engineering construction. Based on the design practices, the principles and methods for the site selection and general layout of heap leaching uranium mill are analyzed and studied. Some problems which should be paid much attention to in the design are discussed in hopes of providing a useful reference for the design and consultation of similar projects. (authors)

  15. Influence of offshore wind farms layout on electrical resonances

    DEFF Research Database (Denmark)

    Holdyk, Andrzej; Holbøll, Joachim; Koldby, Erik

    2014-01-01

    , winding resistances and winding capacitances. Considering the frequency range of the present investigations, up to about 1 MHz, a lumped representation of the transformer characteristics was deemed sufficient. Breakers and capacitors are modelled as ideal components. The chosen wind farm layout includes...... ranges. The results show the influence of specific parameters being varied depending on the farm layout. In particular, cable lengths and transformer broad band characteristics turned out to have significant impact on the results....

  16. Student Perceptions of Textbook Layout and Learnability in Private Schools

    OpenAIRE

    Alefiyah Hoshangabadwala

    2015-01-01

    This research is an exploratory study that investigates students’ perceptions pertinent to textbook layout and organization and their evaluation of the textbook ease of learning. The objective is to find out whether the layout dynamics of school textbooks make any difference in students’ interest in studying or subject understanding. 73 students from various private schools of Pakistan’s cosmopolitan city Karachi responded to a quantitative survey that gauged their percep...

  17. Age and Spatial Peculiarities of Non-neoplastic Diseases of the Skin and Subcutaneous Tissue in Kazakhstan, 2003–2015

    OpenAIRE

    IGISSINOV, Nurbek; KULMIRZAYEVA, Dariyana; BILYALOVA, Zarina; AKPOLATOVA, Gulnur; MAMYRBAYEVA, Marzya; ZHUMAGALIYEVA, Galina

    2017-01-01

    Background: Arrangement of effective management aimed at improving dermatological services and consistent care of patients with skin diseases depends on understanding the epidemiological situation. Methods: This retrospective study presents an epidemiological assessment of non-neoplastic skin and subcutaneous tissue diseases in Kazakhstan registered in 2003–2015. Results: The yearly incidence rate of the diseases among the whole population was in average 3,341.8±121.1 per 100000 population. T...

  18. Towards anatomic scale agent-based modeling with a massively parallel spatially explicit general-purpose model of enteric tissue (SEGMEnT_HPC).

    Science.gov (United States)

    Cockrell, Robert Chase; Christley, Scott; Chang, Eugene; An, Gary

    2015-01-01

    Perhaps the greatest challenge currently facing the biomedical research community is the ability to integrate highly detailed cellular and molecular mechanisms to represent clinical disease states as a pathway to engineer effective therapeutics. This is particularly evident in the representation of organ-level pathophysiology in terms of abnormal tissue structure, which, through histology, remains a mainstay in disease diagnosis and staging. As such, being able to generate anatomic scale simulations is a highly desirable goal. While computational limitations have previously constrained the size and scope of multi-scale computational models, advances in the capacity and availability of high-performance computing (HPC) resources have greatly expanded the ability of computational models of biological systems to achieve anatomic, clinically relevant scale. Diseases of the intestinal tract are exemplary examples of pathophysiological processes that manifest at multiple scales of spatial resolution, with structural abnormalities present at the microscopic, macroscopic and organ-levels. In this paper, we describe a novel, massively parallel computational model of the gut, the Spatially Explicitly General-purpose Model of Enteric Tissue_HPC (SEGMEnT_HPC), which extends an existing model of the gut epithelium, SEGMEnT, in order to create cell-for-cell anatomic scale simulations. We present an example implementation of SEGMEnT_HPC that simulates the pathogenesis of ileal pouchitis, and important clinical entity that affects patients following remedial surgery for ulcerative colitis.

  19. Global scene layout modulates contextual learning in change detection.

    Science.gov (United States)

    Conci, Markus; Müller, Hermann J

    2014-01-01

    Change in the visual scene often goes unnoticed - a phenomenon referred to as "change blindness." This study examined whether the hierarchical structure, i.e., the global-local layout of a scene can influence performance in a one-shot change detection paradigm. To this end, natural scenes of a laid breakfast table were presented, and observers were asked to locate the onset of a new local object. Importantly, the global structure of the scene was manipulated by varying the relations among objects in the scene layouts. The very same items were either presented as global-congruent (typical) layouts or as global-incongruent (random) arrangements. Change blindness was less severe for congruent than for incongruent displays, and this congruency benefit increased with the duration of the experiment. These findings show that global layouts are learned, supporting detection of local changes with enhanced efficiency. However, performance was not affected by scene congruency in a subsequent control experiment that required observers to localize a static discontinuity (i.e., an object that was missing from the repeated layouts). Our results thus show that learning of the global layout is particularly linked to the local objects. Taken together, our results reveal an effect of "global precedence" in natural scenes. We suggest that relational properties within the hierarchy of a natural scene are governed, in particular, by global image analysis, reducing change blindness for local objects through scene learning.

  20. Layout design of user interface components with multiple objectives

    Directory of Open Access Journals (Sweden)

    Peer S.K.

    2004-01-01

    Full Text Available A multi-goal layout problem may be formulated as a Quadratic Assignment model, considering multiple goals (or factors, both qualitative and quantitative in the objective function. The facilities layout problem, in general, varies from the location and layout of facilities in manufacturing plant to the location and layout of textual and graphical user interface components in the human–computer interface. In this paper, we propose two alternate mathematical approaches to the single-objective layout model. The first one presents a multi-goal user interface component layout problem, considering the distance-weighted sum of congruent objectives of closeness relationships and the interactions. The second one considers the distance-weighted sum of congruent objectives of normalized weighted closeness relationships and normalized weighted interactions. The results of first approach are compared with that of an existing single objective model for example task under consideration. Then, the results of first approach and second approach of the proposed model are compared for the example task under consideration.

  1. Global scene layout modulates contextual learning in change detection

    Directory of Open Access Journals (Sweden)

    Markus eConci

    2014-02-01

    Full Text Available Change in the visual scene often goes unnoticed – a phenomenon referred to as ‘change blindness’. This study examined whether the hierarchical structure, i.e., the global-local layout of a scene can influence performance in a one-shot change detection paradigm. To this end, natural scenes of a laid breakfast table were presented, and observers were asked to locate the onset of a new local object. Importantly, the global structure of the scene was manipulated by varying the relations among objects in the scene layouts. The very same items were either presented as global-congruent (typical layouts or as global-incongruent (random arrangements. Change blindness was less severe for congruent than for incongruent displays, and this congruency benefit increased with the duration of the experiment. These findings show that global layouts are learned, supporting detection of local changes with enhanced efficiency. However, performance was not affected by scene congruency in a subsequent control experiment that required observers to localize a static discontinuity (i.e., an object that was missing from the repeated layouts. Our results thus show that learning of the global layout is particularly linked to the local objects. Taken together, our results reveal an effect of global precedence in natural scenes. We suggest that relational properties within the hierarchy of a natural scene are governed, in particular, by global image analysis, reducing change blindness for local objects through scene learning.

  2. Scalable force directed graph layout algorithms using fast multipole methods

    KAUST Repository

    Yunis, Enas Abdulrahman

    2012-06-01

    We present an extension to ExaFMM, a Fast Multipole Method library, as a generalized approach for fast and scalable execution of the Force-Directed Graph Layout algorithm. The Force-Directed Graph Layout algorithm is a physics-based approach to graph layout that treats the vertices V as repelling charged particles with the edges E connecting them acting as springs. Traditionally, the amount of work required in applying the Force-Directed Graph Layout algorithm is O(|V|2 + |E|) using direct calculations and O(|V| log |V| + |E|) using truncation, filtering, and/or multi-level techniques. Correct application of the Fast Multipole Method allows us to maintain a lower complexity of O(|V| + |E|) while regaining most of the precision lost in other techniques. Solving layout problems for truly large graphs with millions of vertices still requires a scalable algorithm and implementation. We have been able to leverage the scalability and architectural adaptability of the ExaFMM library to create a Force-Directed Graph Layout implementation that runs efficiently on distributed multicore and multi-GPU architectures. © 2012 IEEE.

  3. Spatial and temporal MRI profile of ischemic tissue after the acute stages of a permanent mouse model of stroke.

    Science.gov (United States)

    Bogaert-Buchmann, A; Poittevin, M; Po, C; Dupont, D; Sebrié, C; Tomita, Y; Trandinh, A; Seylaz, J; Pinard, E; Méric, P; Kubis, N; Gillet, B

    2013-01-01

    To characterize the progression of injured tissue resulting from a permanent focal cerebral ischemia after the acute phase, Magnetic Resonance Imaging (MRI) monitoring was performed on adult male C57BL/6J mice in the subacute stages, and correlated to histological analyses. Lesions were induced by electrocoagulation of the middle cerebral artery. Serial MRI measurements and weighted-images (T2, T1, T2* and Diffusion Tensor Imaging) were performed on a 9.4T scanner. Histological data (Cresyl-Violet staining and laminin-, Iba1- and GFAP-immunostainings) were obtained 1 and 2 weeks after the stroke. Two days after stroke, tissues assumed to correspond to the infarct core, were detected as a hyperintensity signal area in T2-weighted images. One week later, low-intensity signal areas appeared. Longitudinal MRI study showed that these areas remained present over the following week, and was mainly linked to a drop of the T2 relaxation time value in the corresponding tissues. Correlation with histological data and immuno-histochemistry showed that these areas corresponded to microglial cells. The present data provide, for the first time detailed MRI parameters of microglial cells dynamics, allowing its non-invasive monitoring during the chronic stages of a stroke. This could be particularly interesting in regards to emerging anti-inflammatory stroke therapies.

  4. Classification of mass and normal breast tissue: A convolution neural network classifier with spatial domain and texture images

    International Nuclear Information System (INIS)

    Sahiner, B.; Chan, H.P.; Petrick, N.; Helvie, M.A.; Adler, D.D.; Goodsitt, M.M.; Wei, D.

    1996-01-01

    The authors investigated the classification of regions of interest (ROI's) on mammograms as either mass or normal tissue using a convolution neural network (CNN). A CNN is a back-propagation neural network with two-dimensional (2-D) weight kernels that operate on images. A generalized, fast and stable implementation of the CNN was developed. The input images to the CNN were obtained form the ROI's using two techniques. The first technique employed averaging and subsampling. The second technique employed texture feature extraction methods applied to small subregions inside the ROI. Features computed over different subregions were arranged as texture images, which were subsequently used as CNN inputs. The effects of CNN architecture and texture feature parameters on classification accuracy were studied. Receiver operating characteristic (ROC) methodology was used to evaluate the classification accuracy. A data set consisting of 168 ROI's containing biopsy-proven masses and 504 ROI's containing normal breast tissue was extracted from 168 mammograms by radiologists experienced in mammography. This data set was used for training and testing the CNN. With the best combination of CNN architecture and texture feature parameters, the area under the test ROC curve reached 0.87, which corresponded to a true-positive fraction of 90% at a false positive fraction of 31%. The results demonstrate the feasibility of using a CNN for classification of masses and normal tissue on mammograms

  5. Mapping of the spatial distribution of silver nanoparticles in root tissues of Vicia faba by laser-induced breakdown spectroscopy (LIBS).

    Science.gov (United States)

    Krajcarová, L; Novotný, K; Kummerová, M; Dubová, J; Gloser, V; Kaiser, J

    2017-10-01

    The manuscript presents a procedure for optimal sample preparation and the mapping of the spatial distribution of metal ions and nanoparticles in plant roots using laser-induced breakdown spectroscopy (LIBS) in a double-pulse configuration (DP LIBS) in orthogonal reheating mode. Two Nd:YAG lasers were used; the first one was an ablation laser (UP-266 MACRO, New Wave, USA) with a wavelength of 266nm, and the second one (Brilliant, Quantel, France), with a fundamental wavelength of 1064nm, was used to reheat the microplasma. Seedlings of Vicia faba were cultivated for 7 days in CuSO 4 or AgNO 3 solutions with a concentration of 10µmoll -1 or in a solution of silver nanoparticles (AgNPs) with a concentration of 10µmoll -1 of total Ag, and in distilled water as a control. The total contents of the examined metals in the roots after sample mineralization as well as changes in the concentrations of the metals in the cultivation solutions were monitored by ICP-OES. Root samples embedded in the TissueTek medium and cut into 40µm thick cross sections using the Cryo-Cut Microtome proved to be best suited for an accurate LIBS analysis with a 50µm spatial resolution. 2D raster maps of elemental distribution were created for the emission lines of Cu(I) at 324.754nm and Ag(I) at 328.068nm. The limits of detection of DP LIBS for the root cross sections were estimated to be 4pg for Cu, 18pg for Ag, and 3pg for AgNPs. The results of Ag spatial distribution mapping indicated that unlike Ag + ions, AgNPs do not penetrate into the inner tissues of Vicia faba roots but stay in their outermost layers. The content of Ag in roots cultivated in the AgNP solution was one order of magnitude lower compared to roots cultivated in the metal ion solutions. The significantly smaller concentration of Ag in root tissues cultivated in the AgNP solution also supports the conclusion that the absorption and uptake of AgNPs by roots of Vicia faba is very slow. LIBS mapping of root sections

  6. Design of underground layout and their maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Bok Youn; Kang, Chang Hee; Jo, Young Do; Lim, Sang Taek [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1997-12-01

    Layout of underground structure has to be designed based on rock mechanical analysis and the concept of active support has to be adopted considering the large openings are requested to accommodate heavy duty diesel equipment in underground. Rock bolt and shotcrete will be the most applicable method to support such a large dimensional tunnels. 1) Direction: The main haulage way of the mines where diesel equipment are operating is ramp way system. For optimizing safety measures, and minimizing maintenance cost of the tunnels, it is strongly recommended that all the tunnels including ramp way, rooms and sublevels should be designed in parallel to the direction of principal stress and perpendicular to the direction of major discontinuity. 2) Inclination: Basically, the inclination of the ramp way depends on the specification of the equipment, but 10-15% is usual. The steep inclination needs less initial investment but there will be an adverse effects such as higher operating and maintenance costs. 3) Profile (Cross section): The maximum dimension of the equipment operating in local mines appeared 12.8m long, 3.705m wide and 3.68m high. Considering the dimension, the requested profile simply can be calculated to 4m x 4m, but it should be decided according to the regulated minimum clearances from the walls and roof. The minimum inner curvature radius of the tunnels should be more than 5.2m, and in this case, the tunnel width of the curved zone should be more than 5.5m. 4) Sight distance and braking distance: For the safe operation of the equipment, the sight distance must be longer than braking distance, so that the driver can hold up the equipment safely after finding the obstacles in front of him. The maximum braking distance without heating of brake shoe is 60m. 5) Support and maintenance: Due to the large dimensional tunnels where diesel equipment are operating, the conventional supporting system is not applicable. Therefore, the active support concept should be

  7. Using discrete event simulation to change from a functional layout to a cellular layout in an auto parts industry

    Directory of Open Access Journals (Sweden)

    Thiago Buselato Maurício

    2015-07-01

    Full Text Available This paper presents a discrete event simulation employed in a Brazilian automotive company. There was a huge waste caused by one family scrap. It was believed one reason was the company functional layout. In this case, changing from current to cellular layout, employee synergy and knowledge about this family would increase. Due to the complexity for dimensioning a new cellular layout, mainly because of batch size and client’s demand variation. In this case, discrete event simulation was used, which made possible to introduce those effects improving accuracy in final results. This accuracy will be shown by comparing results obtained with simulation and without it (as company used to do. To conclude, cellular layout was responsible for increasing 15% of productivity, reducing lead-time in 7 days and scrap in 15% for this family.

  8. Microprobing the Molecular Spatial Distribution and Structural Architecture of Feed-type Sorghum Seed Tissue (Sorghum Bicolor L.) using the Synchrotron Radiation Infrared Microspectroscopy Technique

    International Nuclear Information System (INIS)

    Yu, P.

    2011-01-01

    Sorghum seed (Sorghum bicolor L.) has unique degradation and fermentation behaviours compared with other cereal grains such as wheat, barley and corn. This may be related to its cell and cell-wall architecture. The advanced synchrotron radiation infrared microspectroscopy (SR-IMS) technique enables the study of cell or living cell biochemistry within cellular dimensions. The objective of this study was to use the SR-IMS imaging technique to microprobe molecular spatial distribution and cell architecture of the sorghum seed tissue comprehensively. High-density mapping was carried out using SR-IMS on beamline U2B at the National Synchrotron Light Source (Brookhaven National Laboratory, NY, USA). Molecular images were systematically recorded from the outside to the inside of the seed tissue under various chemical functional groups and their ratios [peaks at ∼1725 (carbonyl C=O ester), 1650 (amide I), 1657 (protein secondary structure α-helix), 1628 (protein secondary structure β-sheet), 1550 (amide II), 1515 (aromatic compounds of lignin), 1428, 1371, 1245 (cellulosic compounds in plant seed tissue), 1025 (non-structural CHO, starch granules), 1246 (cellulosic material), 1160 (CHO), 1150 (CHO), 1080 (CHO), 930 (CHO), 860 (CHO), 3350 (OH and NH stretching), 2960 (CH 3 anti-symmetric), 2929 (CH 2 anti-symmetric), 2877 (CH 3 symmetric) and 2848 cm -1 (CH 2 asymmetric)]. The relative protein secondary structure α-helix to β-sheet ratio image, protein amide I to starch granule ratio image, and anti-symmetric CH 3 to CH 2 ratio image were also investigated within the intact sorghum seed tissue. The results showed unique cell architecture, and the molecular spatial distribution and intensity in the sorghum seed tissue (which were analyzed through microprobe molecular imaging) were generated using SR-IMS. This imaging technique and methodology has high potential and could be used for scientists to develop specific cereal grain varieties with targeted food and feed

  9. Age and Spatial Peculiarities of Non-neoplastic Diseases of the Skin and Subcutaneous Tissue in Kazakhstan, 2003-2015.

    Science.gov (United States)

    Igissinov, Nurbek; Kulmirzayeva, Dariyana; Bilyalova, Zarina; Akpolatova, Gulnur; Mamyrbayeva, Marzya; Zhumagaliyeva, Galina

    2017-11-01

    Arrangement of effective management aimed at improving dermatological services and consistent care of patients with skin diseases depends on understanding the epidemiological situation. This retrospective study presents an epidemiological assessment of non-neoplastic skin and subcutaneous tissue diseases in Kazakhstan registered in 2003-2015. The yearly incidence rate of the diseases among the whole population was in average 3,341.8±121.1 per 100000 population. This represents 4835.0±156.1 for children, 5503.2±141.8 for adolescents and 2646.6±106.7 for adults per 100000 inhabitants. Space and time incidence rate was evaluated according to the administrative division. The overall trend decreased to 3.5% in children to 2.8% in adolescents to 1.9%, and in adults to 3.9%. Considerable variation in rates was seen across the country, with highest rates in East Kazakhstan, Mangystau and Aktobe regions, the lowest - in Atyrau and South-Kazakhstan regions. Non-neoplastic diseases of skin and subcutaneous tissue continue to be an urgent public health problem, especially among children in many regions of Kazakhstan.

  10. 32 CFR 553.7 - Design and layout of Army national cemeteries.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true Design and layout of Army national cemeteries... RESERVATIONS AND NATIONAL CEMETERIES ARMY NATIONAL CEMETERIES § 553.7 Design and layout of Army national cemeteries. (a) General cemetery layout plans, landscape planting plans and gravesite layout plans for Army...

  11. Preliminary Design Through Graphs: A Tool for Automatic Layout Distribution

    Directory of Open Access Journals (Sweden)

    Carlo Biagini

    2015-02-01

    Full Text Available Diagrams are essential in the preliminary stages of design for understanding distributive aspects and assisting the decision-making process. By drawing a schematic graph, designers can visualize in a synthetic way the relationships between many aspects: functions and spaces, distribution of layouts, space adjacency, influence of traffic flows within a facility layout, and so on. This process can be automated through the use of modern Information and Communication Technologies tools (ICT that allow the designers to manage a large quantity of information. The work that we will present is part of an on-going research project into how modern parametric software influences decision-making on the basis of automatic and optimized layout distribution. The method involves two phases: the first aims to define the ontological relation between spaces, with particular reference to a specific building typology (rules of aggregation of spaces; the second entails the implementation of these rules through the use of specialist software. The generation of ontological relations begins with the collection of data from historical manuals and analyses of case studies. These analyses aim to generate a “relationship matrix” based on preferences of space adjacency. The phase of implementing the previously defined rules is based on the use of Grasshopper to analyse and visualize different layout configurations. The layout is generated by simulating a process involving the collision of spheres, which represents specific functions of the design program. The spheres are attracted or rejected as a function of the relationships matrix, as defined above. The layout thus obtained will remain in a sort of abstract state independent of information about the exterior form, but will still provide a useful tool for the decision-making process. In addition, preliminary results gathered through the analysis of case studies will be presented. These results provide a good variety

  12. SIMPLIFIED MATHEMATICAL MODEL OF SMALL SIZED UNMANNED AIRCRAFT VEHICLE LAYOUT

    Directory of Open Access Journals (Sweden)

    2016-01-01

    Full Text Available Strong reduction of new aircraft design period using new technology based on artificial intelligence is the key problem mentioned in forecasts of leading aerospace industry research centers. This article covers the approach to devel- opment of quick aerodynamic design methods based on artificial intelligence neural system. The problem is being solved for the classical scheme of small sized unmanned aircraft vehicle (UAV. The principal parts of the method are the mathe- matical model of layout, layout generator of this type of aircraft is built on aircraft neural networks, automatic selection module for cleaning variety of layouts generated in automatic mode, robust direct computational fluid dynamics method, aerodynamic characteristics approximators on artificial neural networks.Methods based on artificial neural networks have intermediate position between computational fluid dynamics methods or experiments and simplified engineering approaches. The use of ANN for estimating aerodynamic characteris-tics put limitations on input data. For this task the layout must be presented as a vector with dimension not exceeding sev-eral hundred. Vector components must include all main parameters conventionally used for layouts description and com- pletely replicate the most important aerodynamics and structural properties.The first stage of the work is presented in the paper. Simplified mathematical model of small sized UAV was developed. To estimate the range of geometrical parameters of layouts the review of existing vehicle was done. The result of the work is the algorithm and computer software for generating the layouts based on ANN technolo-gy. 10000 samples were generated and the dataset containig geometrical and aerodynamic characteristics of layoutwas created.

  13. An efficient biological pathway layout algorithm combining grid-layout and spring embedder for complicated cellular location information.

    Science.gov (United States)

    Kojima, Kaname; Nagasaki, Masao; Miyano, Satoru

    2010-06-18

    Graph drawing is one of the important techniques for understanding biological regulations in a cell or among cells at the pathway level. Among many available layout algorithms, the spring embedder algorithm is widely used not only for pathway drawing but also for circuit placement and www visualization and so on because of the harmonized appearance of its results. For pathway drawing, location information is essential for its comprehension. However, complex shapes need to be taken into account when torus-shaped location information such as nuclear inner membrane, nuclear outer membrane, and plasma membrane is considered. Unfortunately, the spring embedder algorithm cannot easily handle such information. In addition, crossings between edges and nodes are usually not considered explicitly. We proposed a new grid-layout algorithm based on the spring embedder algorithm that can handle location information and provide layouts with harmonized appearance. In grid-layout algorithms, the mapping of nodes to grid points that minimizes a cost function is searched. By imposing positional constraints on grid points, location information including complex shapes can be easily considered. Our layout algorithm includes the spring embedder cost as a component of the cost function. We further extend the layout algorithm to enable dynamic update of the positions and sizes of compartments at each step. The new spring embedder-based grid-layout algorithm and a spring embedder algorithm are applied to three biological pathways; endothelial cell model, Fas-induced apoptosis model, and C. elegans cell fate simulation model. From the positional constraints, all the results of our algorithm satisfy location information, and hence, more comprehensible layouts are obtained as compared to the spring embedder algorithm. From the comparison of the number of crossings, the results of the grid-layout-based algorithm tend to contain more crossings than those of the spring embedder algorithm due to

  14. Plant Layout Analysis by Computer Simulation for Electronic Manufacturing Service Plant

    OpenAIRE

    Visuwan D.; Phruksaphanrat B

    2014-01-01

    In this research, computer simulation is used for Electronic Manufacturing Service (EMS) plant layout analysis. The current layout of this manufacturing plant is a process layout, which is not suitable due to the nature of an EMS that has high-volume and high-variety environment. Moreover, quick response and high flexibility are also needed. Then, cellular manufacturing layout design was determined for the selected group of products. Systematic layout planning (SLP) was used to analyze and de...

  15. A flexible layout design method for passive micromixers.

    Science.gov (United States)

    Deng, Yongbo; Liu, Zhenyu; Zhang, Ping; Liu, Yongshun; Gao, Qingyong; Wu, Yihui

    2012-10-01

    This paper discusses a flexible layout design method of passive micromixers based on the topology optimization of fluidic flows. Being different from the trial and error method, this method obtains the detailed layout of a passive micromixer according to the desired mixing performance by solving a topology optimization problem. Therefore, the dependence on the experience of the designer is weaken, when this method is used to design a passive micromixer with acceptable mixing performance. Several design disciplines for the passive micromixers are considered to demonstrate the flexibility of the layout design method for passive micromixers. These design disciplines include the approximation of the real 3D micromixer, the manufacturing feasibility, the spacial periodic design, and effects of the Péclet number and Reynolds number on the designs obtained by this layout design method. The capability of this design method is validated by several comparisons performed between the obtained layouts and the optimized designs in the recently published literatures, where the values of the mixing measurement is improved up to 40.4% for one cycle of the micromixer.

  16. Genetic Algorithm (GA)-Based Inclinometer Layout Optimization.

    Science.gov (United States)

    Liang, Weijie; Zhang, Ping; Chen, Xianping; Cai, Miao; Yang, Daoguo

    2015-04-17

    This paper presents numerical simulation results of an airflow inclinometer with sensitivity studies and thermal optimization of the printed circuit board (PCB) layout for an airflow inclinometer based on a genetic algorithm (GA). Due to the working principle of the gas sensor, the changes of the ambient temperature may cause dramatic voltage drifts of sensors. Therefore, eliminating the influence of the external environment for the airflow is essential for the performance and reliability of an airflow inclinometer. In this paper, the mechanism of an airflow inclinometer and the influence of different ambient temperatures on the sensitivity of the inclinometer will be examined by the ANSYS-FLOTRAN CFD program. The results show that with changes of the ambient temperature on the sensing element, the sensitivity of the airflow inclinometer is inversely proportional to the ambient temperature and decreases when the ambient temperature increases. GA is used to optimize the PCB thermal layout of the inclinometer. The finite-element simulation method (ANSYS) is introduced to simulate and verify the results of our optimal thermal layout, and the results indicate that the optimal PCB layout greatly improves (by more than 50%) the sensitivity of the inclinometer. The study may be useful in the design of PCB layouts that are related to sensitivity improvement of gas sensors.

  17. Vertical Object Layout and Compression for Fixed Heaps

    Science.gov (United States)

    Titzer, Ben L.; Palsberg, Jens

    Research into embedded sensor networks has placed increased focus on the problem of developing reliable and flexible software for microcontroller-class devices. Languages such as nesC [10] and Virgil [20] have brought higher-level programming idioms to this lowest layer of software, thereby adding expressiveness. Both languages are marked by the absence of dynamic memory allocation, which removes the need for a runtime system to manage memory. While nesC offers code modules with statically allocated fields, arrays and structs, Virgil allows the application to allocate and initialize arbitrary objects during compilation, producing a fixed object heap for runtime. This paper explores techniques for compressing fixed object heaps with the goal of reducing the RAM footprint of a program. We explore table-based compression and introduce a novel form of object layout called vertical object layout. We provide experimental results that measure the impact on RAM size, code size, and execution time for a set of Virgil programs. Our results show that compressed vertical layout has better execution time and code size than table-based compression while achieving more than 20% heap reduction on 6 of 12 benchmark programs and 2-17% heap reduction on the remaining 6. We also present a formalization of vertical object layout and prove tight relationships between three styles of object layout.

  18. Layout design in order to improve efficiency in manufacturing

    Science.gov (United States)

    Siregar, I.; Tarigan, U.; Nasution, T. H.

    2018-02-01

    This research was conducted at the company that produces bobbins and ream type cigarette paper. Problems that found on the production process is the back and forth (back tracking) movement. Back and forth (back tracking) movement extending the total distance moved by the material and increase the total moment of transfer materials thus reducing the efficiency of the transfer of materials in the production process. The purpose of this study is to give design for the layout of production facilities in the company, so that the expected production produced by the company can reach the targets set by the management company. The method used in this research is the Graph-Based Construction and Travel Chart Method. The results of the analysis of the proposed layout with Graph-Based Construction was selected with a total value that is equal to the moment of transfer of 780 758 m / year. This result is better than the actual layout in the amount of 1,021,038.12 meters / year and the results of the method Travel Alternative Chart I of 826.236,60 meters/year, Alternative II of 1.004.433,56 meters / year, and Alternative III for 828,467.12 meters/year. The design layout of Graph-Based Construction material increases the transfer efficiency for 23.53%. With this layout proposal, expected production capacity will be increased along with the shortening of the distance of the displacement that must be passed by the material to be processed.

  19. Optimization of offshore wind farm layout in restricted zones

    International Nuclear Information System (INIS)

    Hou, Peng; Hu, Weihao; Chen, Cong; Soltani, Mohsen; Chen, Zhe

    2016-01-01

    In this research, an optimization method for offshore wind farm layout design is proposed. With the purpose of maximizing the energy production of the wind farm, the wind turbine (WT) positions are optimized. Due to the limitations of seabed conditions, marine traffic limitations or shipwrecks, etc., the WTs are expected to be placed outside specific areas. Based on this fact, a restriction zone concept is proposed in this paper and implemented with the penalty function method. In order to find a feasible solution, a recent proposed stochastic algorithm, particle swarm optimization algorithm with multiple adaptive methods (PSO-MAM) is adopted. The simulation results indicate that the proposed method can find a layout which outperforms a baseline layout of a reference wind farm (RWF) by increasing the energy yield by 3.84%. - Highlights: • The offshore restricted area concept is proposed. • The recent developed PSO-MAM algorithm is arranged to optimize the layout. • The penalty function method is adopted to help find the feasible solution. • The optimized layout increases energy yields 3.84% than reference wind farm.

  20. Conceptual layout design of CFETR Hot Cell Facility

    Energy Technology Data Exchange (ETDEWEB)

    Gong, Zheng, E-mail: gongz@mail.ustc.edu.cn [University of Science and Technology of China, Hefei 230026 (China); Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Qi, Minzhong, E-mail: qiminzhong@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Cheng, Yong, E-mail: chengyong@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Song, Yuntao, E-mail: songyt@ipp.ac.cn [University of Science and Technology of China, Hefei 230026 (China); Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China)

    2015-11-15

    Highlights: • This article proposed a conceptual layout design for CFETR. • The design principles are to support efficient maintenance to ensure the realization of high duty time. • The preliminary maintenance process and logistics are described in detail. • Life cycle management, maneuverability, risk and safety are in the consideration of design. - Abstract: CFETR (China Fusion Engineering Test Reactor) is new generation of Tokomak device beyond EAST in China. An overview of hot cell layout design for CFETR has been proposed by ASIPP&USTC. Hot Cell, as major auxiliary facility, not only plays a pivotal role in supporting maintenance to meet the requirements of high duty time 0.3–0.5 but also supports installation and decommissioning. Almost all of the Tokomak devices are lateral handling internal components like ITER and JET, but CFETR maintain the blanket module from 4 vertical ports, which is quite a big challenge for the hot cell layout design. The activated in-vessel components and several diagnosis instruments will be repaired and refurbished in the Hot Cell Facility, so the appropriate layout is very important to the Hot Cell Facility to ensure the high duty time, it is divided into different parts equipped with a variety of RH equipment and diagnosis devices based on the functional requirements. The layout of the Hot Cell Facility should make maintenance process more efficient and reliable, and easy to service and rescue when a sudden events taking place, that is the capital importance issue considered in design.

  1. Spatial and Social Networks in Organizational Innovation

    Science.gov (United States)

    Wineman, Jean D.; Kabo, Felichism W.; Davis, Gerald F.

    2009-01-01

    Research on the enabling factors of innovation has focused on either the social component of organizations or on the spatial dimensions involved in the innovation process. But no one has examined the aggregate consequences of the link from spatial layout, to social networks, to innovation. This project enriches our understanding of how innovation…

  2. Biochemical and physiological modifications in tissues of Sardina pilchardus: spatial and temporal patterns as a baseline for biomonitoring studies

    Directory of Open Access Journals (Sweden)

    Bruno Silva Nunes

    2015-02-01

    Full Text Available Sardina pilchardus is a marine species common in the North Atlantic Ocean, and is subjected to diffuse anthropogenic chemical contamination and seasonal fluctuations in biotic and abiotic parameters that may alter its physiology and condition. Biological material is easily available through commercial fisheries, which could facilitate its use as a bioindicator species. The aim of the present work was to address its potential inclusion in biomonitoring studies, considering a combinatory approach through the use of enzymatic biomarkers and somatic indices, by assessing spatial and temporal patterns in a metapopulation along the west coast of Portugal. Our results showed significant variability of the biochemical and physiological profile of the fish, mainly concordant between sampling sites. Large differences for most markers were found across periods of the year, showing the importance of seasonality, which was mostly related to the reproductive cycle. Hence, environmental scientists should acknowledge seasonality as a strong driving force for physiological adaptations, influencing biochemical markers that are normally used to identify effects of chemical contamination. The here-obtained set of data suggests that S. pilchardus may be successfully included in oceanic biomonitoring studies, when one considers that the contribution of seasonal factors may exceed the influence of eventual anthropogenic contamination.

  3. Joint Graph Layouts for Visualizing Collections of Segmented Meshes

    KAUST Repository

    Ren, Jing; Schneider, Jens; Ovsjanikov, Maks; Wonka, Peter

    2017-01-01

    We present a novel and efficient approach for computing joint graph layouts and then use it to visualize collections of segmented meshes. Our joint graph layout algorithm takes as input the adjacency matrices for a set of graphs along with partial, possibly soft, correspondences between nodes of different graphs. We then use a two stage procedure, where in the first step, we extend spectral graph drawing to include a consistency term so that a collection of graphs can be handled jointly. Our second step extends metric multi-dimensional scaling with stress majorization to the joint layout setting, while using the output of the spectral approach as initialization. Further, we discuss a user interface for exploring a collection of graphs. Finally, we show multiple example visualizations of graphs stemming from collections of segmented meshes and we present qualitative and quantitative comparisons with previous work.

  4. Effect of layout on surge line thermal stratification

    International Nuclear Information System (INIS)

    Lai Jianyong; Huang Wei

    2011-01-01

    In order to analyze and evaluate the effect of layout on the thermal stratification for PWR Pressurizer surge line, numerical simulation by Computational Fluid Dynamics (CFD) method is taken on 6 kinds of layout improvement with 2 improvement schemes, i.e., increasing the obliquity of quasi horizontal section and adding a vertical pipe between the quasi horizontal section and next elbow, and the maximum temperature differences of quasi horizontal section of surge line of various layouts under different flowrate are obtained. The comparison shows that, the increasing of the obliquity of quasi horizontal section can mitigate the thermal stratification phenomena but can not eliminate this phenomena, while the adding of a vertical pipe between the quasi horizontal section and next elbow can effectively mitigate and eliminate the thermal stratification phenomena. (authors)

  5. Production layout improvement in emergency services: a participatory approach.

    Science.gov (United States)

    Zanatta, Mateus; Amaral, Fernando Gonçalves

    2012-01-01

    Volunteer fire department is a service that responds emergency situations in places where there are no military emergency services. These services need to respond quickly, because time is often responsible for the operation success besides work environment and setup time interfere with the prompt response to these calls and care efficiency. The layout design is one factor that interferes with the quick setup. In this case, the spaces arrangement can result in excessive or unnecessary movements; also the equipment provision may hinder the selection and collection of these or even create movement barriers for the workers. This work created a new layout for the emergency assistance service, considering the human factors related to work through the task analysis and workers participation on the alternatives of improvement. The results showed an alternate layout with corridors and minimization of unusable sites, allowing greater flexibility and new possibilities of requirements.

  6. Analysis of Sequence Diagram Layout in Advanced UML Modelling Tools

    Directory of Open Access Journals (Sweden)

    Ņikiforova Oksana

    2016-05-01

    Full Text Available System modelling using Unified Modelling Language (UML is the task that should be solved for software development. The more complex software becomes the higher requirements are stated to demonstrate the system to be developed, especially in its dynamic aspect, which in UML is offered by a sequence diagram. To solve this task, the main attention is devoted to the graphical presentation of the system, where diagram layout plays the central role in information perception. The UML sequence diagram due to its specific structure is selected for a deeper analysis on the elements’ layout. The authors research represents the abilities of modern UML modelling tools to offer automatic layout of the UML sequence diagram and analyse them according to criteria required for the diagram perception.

  7. Optimization of Orchestral Layouts Based on Instrument Directivity Patterns

    Science.gov (United States)

    Stroud, Nathan Paul

    The experience of hearing an exceptional symphony orchestra perform in an excel- lent concert hall can be profound and moving, causing a level of excitement not often reached for listeners. Romantic period style orchestral music, recognized for validating the use of intense emotion for aesthetic pleasure, was the last significant development in the history of the orchestra. In an age where orchestral popularity is waning, the possibil- ity of evolving the orchestral sound in our modern era exists through the combination of our current understanding of instrument directivity patterns and their interaction with architectural acoustics. With the aid of wave field synthesis (WFS), newly proposed variations on orchestral layouts are tested virtually using a 64-channel WFS array. Each layout is objectively and subjectively compared for determination of which layout could optimize the sound of the orchestra and revitalize the excitement of the performance.

  8. Joint Graph Layouts for Visualizing Collections of Segmented Meshes

    KAUST Repository

    Ren, Jing

    2017-09-12

    We present a novel and efficient approach for computing joint graph layouts and then use it to visualize collections of segmented meshes. Our joint graph layout algorithm takes as input the adjacency matrices for a set of graphs along with partial, possibly soft, correspondences between nodes of different graphs. We then use a two stage procedure, where in the first step, we extend spectral graph drawing to include a consistency term so that a collection of graphs can be handled jointly. Our second step extends metric multi-dimensional scaling with stress majorization to the joint layout setting, while using the output of the spectral approach as initialization. Further, we discuss a user interface for exploring a collection of graphs. Finally, we show multiple example visualizations of graphs stemming from collections of segmented meshes and we present qualitative and quantitative comparisons with previous work.

  9. Ergonomics and simulation-based approach in improving facility layout

    Science.gov (United States)

    Abad, Jocelyn D.

    2018-02-01

    The use of the simulation-based technique in facility layout has been a choice in the industry due to its convenience and efficient generation of results. Nevertheless, the solutions generated are not capable of addressing delays due to worker's health and safety which significantly impact overall operational efficiency. It is, therefore, critical to incorporate ergonomics in facility design. In this study, workstation analysis was incorporated into Promodel simulation to improve the facility layout of a garment manufacturing. To test the effectiveness of the method, existing and improved facility designs were measured using comprehensive risk level, efficiency, and productivity. Results indicated that the improved facility layout generated a decrease in comprehensive risk level and rapid upper limb assessment score; an increase of 78% in efficiency and 194% increase in productivity compared to existing design and thus proved that the approach is effective in attaining overall facility design improvement.

  10. Optimization of Wind Farm Layout in Complex Terrain

    DEFF Research Database (Denmark)

    Xu, Chang; Yang, Jianchuan; Li, Chenqi

    2013-01-01

    Microscopic site selection for wind farms in complex terrain is a technological difficulty in the development of onshore wind farms. This paper presented a method for optimizing wind farm layout in complex terrain. This method employed Lissaman and Jensen wake models, took wind velocity distribut......Microscopic site selection for wind farms in complex terrain is a technological difficulty in the development of onshore wind farms. This paper presented a method for optimizing wind farm layout in complex terrain. This method employed Lissaman and Jensen wake models, took wind velocity...... are subject to boundary conditions and minimum distance conditions. The improved genetic algorithm (GA) for real number coding was used to search the optimal result. Then the optimized result was compared to the result from the experienced layout method. Results show the advantages of the present method...

  11. Student Perceptions of Textbook Layout and Learnability in Private Schools

    Directory of Open Access Journals (Sweden)

    Alefiyah Hoshangabadwala

    2015-06-01

    Full Text Available This research is an exploratory study that investigates students’ perceptions pertinent to textbook layout and organization and their evaluation of the textbook ease of learning. The objective is to find out whether the layout dynamics of school textbooks make any difference in students’ interest in studying or subject understanding. 73 students from various private schools of Pakistan’s cosmopolitan city Karachi responded to a quantitative survey that gauged their perceptions regarding textbook components such as paper, print, color, and textbook pedagogical features. Findings indicate that students rank print and color above paper quality, and that there is no particular relationship between a book layout and the actual use of textbooks.

  12. Urban pattern: Layout design by hierarchical domain splitting

    KAUST Repository

    Yang, Yongliang; Wang, Jun; Vouga, Etienne; Wonka, Peter

    2013-01-01

    We present a framework for generating street networks and parcel layouts. Our goal is the generation of high-quality layouts that can be used for urban planning and virtual environments. We propose a solution based on hierarchical domain splitting using two splitting types: streamline-based splitting, which splits a region along one or multiple streamlines of a cross field, and template-based splitting, which warps pre-designed templates to a region and uses the interior geometry of the template as the splitting lines. We combine these two splitting approaches into a hierarchical framework, providing automatic and interactive tools to explore the design space.

  13. Urban pattern: Layout design by hierarchical domain splitting

    KAUST Repository

    Yang, Yongliang

    2013-11-06

    We present a framework for generating street networks and parcel layouts. Our goal is the generation of high-quality layouts that can be used for urban planning and virtual environments. We propose a solution based on hierarchical domain splitting using two splitting types: streamline-based splitting, which splits a region along one or multiple streamlines of a cross field, and template-based splitting, which warps pre-designed templates to a region and uses the interior geometry of the template as the splitting lines. We combine these two splitting approaches into a hierarchical framework, providing automatic and interactive tools to explore the design space.

  14. Collimator Layouts for HL-LHC in the Experimental Insertions

    CERN Document Server

    Bruce, R; Esposito, Luigi Salvatore; Jowett, John; Lechner, Anton; Quaranta, Elena; Redaelli, Stefano; Schaumann, Michaela; Skordis, Eleftherios; Eleanor Steele, G; Garcia Morales, H; Kwee-Hinzmann, Regina

    2015-01-01

    This paper presents the layout of collimators for HL-LHC in the experimental insertions. On the incoming beam, we propose to install additional tertiary collimators to protect potential new aperture bottlenecks in cells 4 and 5, which in addition reduce the experimental background. For the outgoing beam, the layout of the present LHC with three physics debris absorbers gives sufficient protection for highluminosity proton operation. However, collisional processes for heavy ions cause localized beam losses with the potential to quench magnets. To alleviate these losses, an installation of dispersion suppressor collimators is proposed.

  15. An Evolutionary Approach for Robust Layout Synthesis of MEMS

    DEFF Research Database (Denmark)

    Fan, Zhun; Wang, Jiachuan; Goodman, Erik

    2005-01-01

    The paper introduces a robust design method for layout synthesis of MEM resonators subject to inherent geometric uncertainties such as the fabrication error on the sidewall of the structure. The robust design problem is formulated as a multi-objective constrained optimisation problem after certain...... assumptions and treated with multiobjective genetic algorithm (MOGA), a special type of evolutionary computing approaches. Case study based on layout synthesis of a comb-driven MEM resonator shows that the approach proposed in this paper can lead to design results that meet the target performance and are less...

  16. Testing of polarimeter UVP layout on telescope AZT-2

    Science.gov (United States)

    Nevodovskyi, P. V.; Vidmachenko, A. P.; Morozhenko, O. V.

    2018-05-01

    Layout of on-board small-sized ultraviolet polarimeter was created. On its basis a ground version of the layout was prepared. It was installed on the AZT-2 telescope for carrying out special tests. With this device we investigated the possibility of determining the degree of polarization of the twilight glow of the Earth's atmosphere, and also worked out the observation methodology required for such work, and the basic principles of the implementation of this method. For this purpose, a special complex of auxiliary equipment was developed.

  17. Complete PCB design using OrCAD capture and layout

    CERN Document Server

    Mitzner, Kraig

    2011-01-01

    This book provides instruction on how to use the OrCAD design suite to design and manufacture printed circuit boards. The book is written for both students and practicing engineers who need a quick tutorial on how to use the software and who need in-depth knowledge of the capabilities and limitations of the software package. There are two goals the book aims to reach:The primary goal is to show the reader how to design a PCB using OrCAD Capture and OrCAD Layout. Capture is used to build the schematic diagram of the circuit, and Layout is used to design the circuit board so that

  18. LIDAR TS for ITER core plasma. Part I: layout & hardware

    Science.gov (United States)

    Salzmann, H.; Gowers, C.; Nielsen, P.

    2017-12-01

    The original time-of-flight design of the Thomson scattering diagnostic for the ITER core plasma has been shown up by ITER. This decision was justified by insufficiencies of some of the components. In this paper we show that with available, present day technology a LIDAR TS system is feasible which meets all the ITER specifications. As opposed to the conventional TS system the LIDAR TS also measures the high field side of the plasma. The optical layout of the front end has been changed only little in comparison with the latest one considered by ITER. The main change is that it offers an optical collection without any vignetting over the low field side. The throughput of the system is defined only by the size and the angle of acceptance of the detectors. This, in combination with the fact that the LIDAR system uses only one set of spectral channels for the whole line of sight, means that no absolute calibration using Raman or Rayleigh scattering from a non-hydrogen isotope gas fill of the vessel is needed. Alignment of the system is easy since the collection optics view the footprint of the laser on the inner wall. In the described design we use, simultaneously, two different wavelength pulses from a Nd:YAG laser system. Its fundamental wavelength ensures measurements of 2 keV up to more than 40 keV, whereas the injection of the second harmonic enables measurements of low temperatures. As it is the purpose of this paper to show the technological feasibility of the LIDAR system, the hardware is considered in Part I of the paper. In Part II we demonstrate by numerical simulations that the accuracy of the measurements as required by ITER is maintained throughout the given plasma parameter range. The effect of enhanced background radiation in the wavelength range 400 nm-500 nm is considered. In Part III the recovery of calibration in case of changing spectral transmission of the front end is treated. We also investigate how to improve the spatial resolution at the

  19. Quantitative spatially resolved measurement of tissue chromophore concentrations using photoacoustic spectroscopy: application to the measurement of blood oxygenation and haemoglobin concentration

    Science.gov (United States)

    Laufer, Jan; Delpy, Dave; Elwell, Clare; Beard, Paul

    2007-01-01

    A new approach based on pulsed photoacoustic spectroscopy for non-invasively quantifying tissue chromophore concentrations with high spatial resolution has been developed. The technique is applicable to the quantification of tissue chromophores such as oxyhaemoglobin (HbO2) and deoxyhaemoglobin (HHb) for the measurement of physiological parameters such as blood oxygen saturation (SO2) and total haemoglobin concentration. It can also be used to quantify the local accumulation of targeted contrast agents used in photoacoustic molecular imaging. The technique employs a model-based inversion scheme to recover the chromophore concentrations from photoacoustic measurements. This comprises a numerical forward model of the detected time-dependent photoacoustic signal that incorporates a multiwavelength diffusion-based finite element light propagation model to describe the light transport and a time-domain acoustic model to describe the generation, propagation and detection of the photoacoustic wave. The forward model is then inverted by iteratively fitting it to measurements of photoacoustic signals acquired at different wavelengths to recover the chromophore concentrations. To validate this approach, photoacoustic signals were generated in a tissue phantom using nanosecond laser pulses between 740 nm and 1040 nm. The tissue phantom comprised a suspension of intralipid, blood and a near-infrared dye in which three tubes were immersed. Blood at physiological haemoglobin concentrations and oxygen saturation levels ranging from 2% to 100% was circulated through the tubes. The signal amplitude from different temporal sections of the detected photoacoustic waveforms was plotted as a function of wavelength and the forward model fitted to these data to recover the concentrations of HbO2 and HHb, total haemoglobin concentration and SO2. The performance was found to compare favourably to that of a laboratory CO-oximeter with measurement resolutions of ±3.8 g l-1 (±58 µM) and ±4

  20. Quantitative spatially resolved measurement of tissue chromophore concentrations using photoacoustic spectroscopy: application to the measurement of blood oxygenation and haemoglobin concentration

    Energy Technology Data Exchange (ETDEWEB)

    Laufer, Jan; Delpy, Dave; Elwell, Clare; Beard, Paul [Department of Medical Physics and Bioengineering, University College London, Malet Place Engineering Building, London WC1E 6BT (United Kingdom)

    2007-01-07

    A new approach based on pulsed photoacoustic spectroscopy for non-invasively quantifying tissue chromophore concentrations with high spatial resolution has been developed. The technique is applicable to the quantification of tissue chromophores such as oxyhaemoglobin (HbO{sub 2}) and deoxyhaemoglobin (HHb) for the measurement of physiological parameters such as blood oxygen saturation (SO{sub 2}) and total haemoglobin concentration. It can also be used to quantify the local accumulation of targeted contrast agents used in photoacoustic molecular imaging. The technique employs a model-based inversion scheme to recover the chromophore concentrations from photoacoustic measurements. This comprises a numerical forward model of the detected time-dependent photoacoustic signal that incorporates a multiwavelength diffusion-based finite element light propagation model to describe the light transport and a time-domain acoustic model to describe the generation, propagation and detection of the photoacoustic wave. The forward model is then inverted by iteratively fitting it to measurements of photoacoustic signals acquired at different wavelengths to recover the chromophore concentrations. To validate this approach, photoacoustic signals were generated in a tissue phantom using nanosecond laser pulses between 740 nm and 1040 nm. The tissue phantom comprised a suspension of intralipid, blood and a near-infrared dye in which three tubes were immersed. Blood at physiological haemoglobin concentrations and oxygen saturation levels ranging from 2% to 100% was circulated through the tubes. The signal amplitude from different temporal sections of the detected photoacoustic waveforms was plotted as a function of wavelength and the forward model fitted to these data to recover the concentrations of HbO{sub 2} and HHb, total haemoglobin concentration and SO{sub 2}. The performance was found to compare favourably to that of a laboratory CO-oximeter with measurement resolutions of {+-}3

  1. Quantitative spatially resolved measurement of tissue chromophore concentrations using photoacoustic spectroscopy: application to the measurement of blood oxygenation and haemoglobin concentration

    International Nuclear Information System (INIS)

    Laufer, Jan; Delpy, Dave; Elwell, Clare; Beard, Paul

    2007-01-01

    A new approach based on pulsed photoacoustic spectroscopy for non-invasively quantifying tissue chromophore concentrations with high spatial resolution has been developed. The technique is applicable to the quantification of tissue chromophores such as oxyhaemoglobin (HbO 2 ) and deoxyhaemoglobin (HHb) for the measurement of physiological parameters such as blood oxygen saturation (SO 2 ) and total haemoglobin concentration. It can also be used to quantify the local accumulation of targeted contrast agents used in photoacoustic molecular imaging. The technique employs a model-based inversion scheme to recover the chromophore concentrations from photoacoustic measurements. This comprises a numerical forward model of the detected time-dependent photoacoustic signal that incorporates a multiwavelength diffusion-based finite element light propagation model to describe the light transport and a time-domain acoustic model to describe the generation, propagation and detection of the photoacoustic wave. The forward model is then inverted by iteratively fitting it to measurements of photoacoustic signals acquired at different wavelengths to recover the chromophore concentrations. To validate this approach, photoacoustic signals were generated in a tissue phantom using nanosecond laser pulses between 740 nm and 1040 nm. The tissue phantom comprised a suspension of intralipid, blood and a near-infrared dye in which three tubes were immersed. Blood at physiological haemoglobin concentrations and oxygen saturation levels ranging from 2% to 100% was circulated through the tubes. The signal amplitude from different temporal sections of the detected photoacoustic waveforms was plotted as a function of wavelength and the forward model fitted to these data to recover the concentrations of HbO 2 and HHb, total haemoglobin concentration and SO 2 . The performance was found to compare favourably to that of a laboratory CO-oximeter with measurement resolutions of ±3.8 g l -1 (±58

  2. Evidence-based ergonomics. A comparison of Japanese and American office layouts.

    Science.gov (United States)

    Noro, Kageyu; Fujimaki, Goroh; Kishi, Shinsuke

    2003-01-01

    There is a variety of alternatives in office layouts. Yet the theoretical basis and criteria for predicting how well these layouts accommodate employees are poorly understood. The objective of this study was to evaluate criteria for selecting office layouts. Intensive computer workers worked in simulated office layouts in a controlled experimental laboratory. Eye movement measures indicate that knowledge work requires both concentration and interaction. Findings pointed to one layout as providing optimum balance between these 2 requirements. Recommendations for establishing a theoretical basis and design criteria for selecting office layouts based on work style are suggested.

  3. CONTROLLABILITY OF TRADITIONAL NEIGHBORHOOD AND ITS SIMPLIFIED LAYOUT

    Directory of Open Access Journals (Sweden)

    M. Salim Ferwati

    2010-03-01

    Full Text Available Street hierarchy, as a way of presenting intended information, conforms to social rules that underlay architectural and urban designs to create public, semi-public, and semi-private. These social rules have the responsibility to convey necessary information about place to outsiders as well as to insiders. This research looks at urban spaces as physical structures that represent foci of attention of users and that are collectively a part of the social pattern framework. The argument of this study is that connectivity and forms of streets house certain social rules that intended to serve users, so that any changes in the street layout lead to changes in its social rules. As a case study, the complexity of a walled Arab neighborhood was examined through Sur Lawatyia, located in Muscat Governorate, Oman. By replacing the curvilinear and broken streets of this neighborhood with straight ones; a simplified street layout was derived. Then, a comparison of both street layouts was carried out through mapping, tabulation, charts, correlation test, and with reliance on the method of measurement of street control values introduced by Hillier and Hanson in 1984. The result was that the simple form is far short to be the representation of the space syntax of the traditional street layout.

  4. Seismic analysis of a reactor building with eccentric layout

    International Nuclear Information System (INIS)

    Itoh, T.; Deng, D.Z.F.; Lui, K.

    1987-01-01

    Conventional design for a reactor building in a high seismic area has adopted an essentially concentric layout in response to fear of excessive torsional effect due to horizontal seismic load on an eccentric plant. This concentric layout requirement generally results in an inflexible arrangement of the plant facilities and thus increases the plant volume. This study is performed to investigate the effect of eccentricity on the overall seismic structural response and to provide technical information in this regard to substantiate the volume reduction of the overall power plant. The plant layout is evolved from the Bechtel standard plan of a PWR plant by integrating the reactor building and the auxiliary building into a combined building supported on a common basemat. This plant layout is optimized for volume utilization and to reduce the length of piping systems. The mass centers at various elevations of the combined building do not coincide with the rigidity center (RC) of the respective floor and the geometric center of the basemat, thus creating an eccentric response of the building in a seismic environment. Therefore, the torsional effects of the structure have to be taken into account in the seismic analysis

  5. An online planning tool for designing terrace layouts

    Science.gov (United States)

    A web-based conservation planning tool, WebTERLOC (web-based Terrace Location Program), was developed to provide multiple terrace layout options using digital elevation model (DEM) and geographic information systems (GIS). Development of a terrace system is complicated by the time-intensive manual ...

  6. Why multicamp layouts? | BR | African Journal of Range and Forage ...

    African Journals Online (AJOL)

    Although it has become standard practice in Southern Africa to recommend grazing systems based on a maximum of five camps, there are indications that the use of multicamp layouts, employing a greater number of camps per herd, may increase the efficiency of animal production from natural veld. The basic advantage of ...

  7. Modeling human-machine interactions for operations room layouts

    Science.gov (United States)

    Hendy, Keith C.; Edwards, Jack L.; Beevis, David

    2000-11-01

    The LOCATE layout analysis tool was used to analyze three preliminary configurations for the Integrated Command Environment (ICE) of a future USN platform. LOCATE develops a cost function reflecting the quality of all human-human and human-machine communications within a workspace. This proof- of-concept study showed little difference between the efficacy of the preliminary designs selected for comparison. This was thought to be due to the limitations of the study, which included the assumption of similar size for each layout and a lack of accurate measurement data for various objects in the designs, due largely to their notional nature. Based on these results, the USN offered an opportunity to conduct a LOCATE analysis using more appropriate assumptions. A standard crew was assumed, and subject matter experts agreed on the communications patterns for the analysis. Eight layouts were evaluated with the concepts of coordination and command factored into the analysis. Clear differences between the layouts emerged. The most promising design was refined further by the USN, and a working mock-up built for human-in-the-loop evaluation. LOCATE was applied to this configuration for comparison with the earlier analyses.

  8. Proximity search heuristics for wind farm optimal layout

    DEFF Research Database (Denmark)

    Fischetti, Martina; Monaci, Michele

    2016-01-01

    A heuristic framework for turbine layout optimization in a wind farm is proposed that combines ad-hoc heuristics and mixed-integer linear programming. In our framework, large-scale mixed-integer programming models are used to iteratively refine the current best solution according to the recently...

  9. FOOD safety and hygiene - Systematic layout planning of food processes

    NARCIS (Netherlands)

    Van Donk, DP; Gaalman, G

    2004-01-01

    Hygiene and food safety have been dealt with from different fields of science such as biology and health, and from different angles such as HACCP and GMP. Little systematically ordered knowledge is available for the analysis of a layout, taking hygienic factors into account. HACCP and GMP are

  10. Hydrodynamic Modelling and Layout Optimisation of Wave Energy Converter Arrays

    DEFF Research Database (Denmark)

    Ruiz, Pau Mercadé

    2017-01-01

    in various positions and orientations are finally investigated. This thesis intends in this way to offer a practical approach to the analysis of wave energy converters when they operate together as an array and the optimal design of array layouts. The topics covered by the text include propagation of waves...

  11. A New Data Layout For Set Intersection on GPUs

    DEFF Research Database (Denmark)

    Amossen, Rasmus Resen; Pagh, Rasmus

    2011-01-01

    . However, GPUs require highly regular control flow and memory access patterns, and for this reason previous GPU methods for intersecting sets have used a simple bitmap representation. This representation requires excessive space on sparse data sets. In this paper we present a novel data layout, BATMAP...

  12. Preconceptual ABC design definition and system configuration layout: Appendix A

    International Nuclear Information System (INIS)

    1995-03-01

    The mission of the ABC system is to destroy as effectively as possible the fissile material inserted into the core without producing any new fissile material. The contents of this report are as follows: operating conditions for the steam-cycle ABC system; flow rates and component dimensions; drawings of the ABC layout; and impact of core design parameters on containment size

  13. Layout considerations for the PSB H- injection system

    CERN Document Server

    Aiba, M; Carli, C; Chanel, M; Fowler, A; Goddard, B; Weterings, W

    2009-01-01

    The layout of the PSB H- injection system is described, including the arguments for the geometry and the required equipment performance parameters. The longitudinal positions of the main elements are specified, together with the injected and circulating beam axes. The assumptions used in determining the geometry are listed.

  14. Product Category Layout and Organization: Retail Placement of Food Products

    NARCIS (Netherlands)

    Herpen, van E.

    2016-01-01

    This article discusses the placement of food products in retail stores, in particular how the placement of food products can influence how consumers perceive the store in general and these products in particular. It reviews the overall layout of the store, assortment organization, and shelf

  15. Preconceptual ABC design definition and system configuration layout

    International Nuclear Information System (INIS)

    Barthold, W.

    1995-03-01

    This document is the conceptual design document for the follow-on to the Molten Salt Breeder Reactor, known as the ABC type reactor. It addresses blanket design options, containment options, off-gas systems, drainage systems, and components/layouts of the primary, secondary, and tertiary systems, and it contains a number of diagrams for the configuration of the major systems

  16. Performance evaluation of cellular layouts : extension to DRC system contexts

    NARCIS (Netherlands)

    Suresh, NC; Gaalman, GJC

    This study involves a comparison of the performance of functional layouts (FL) and cellular manufacturing (CM) systems in a dual-resource-constrained( DRC) system context. Past studies of FL and CM have been based mostly on single-resource-constrained( SRC) systems. Recent studies have included

  17. Measurement of fluorophore concentrations and fluorescence quantum yield in tissue-simulating phantoms using three diffusion models of steady-state spatially resolved fluorescence

    Energy Technology Data Exchange (ETDEWEB)

    Diamond, Kevin R; Farrell, Thomas J; Patterson, Michael S [Department of Medical Physics, Juravinski Cancer Centre and McMaster University, 699 Concession Street, Hamilton, Ontario L8V 5C2 (Canada)

    2003-12-21

    Steady-state diffusion theory models of fluorescence in tissue have been investigated for recovering fluorophore concentrations and fluorescence quantum yield. Spatially resolved fluorescence, excitation and emission reflectance were calculated by diffusion theory and Monte Carlo simulations, and measured using a multi-fibre probe on tissue-simulating phantoms containing either aluminium phthalocyanine tetrasulfonate (AlPcS{sub 4}), Photofrin or meso-tetra-(4-sulfonatophenyl)-porphine dihydrochloride (TPPS{sub 4}). The accuracy of the fluorophore concentration and fluorescence quantum yield recovered by three different models of spatially resolved fluorescence were compared. The models were based on: (a) weighted difference of the excitation and emission reflectance, (b) fluorescence due to a point excitation source or (c) fluorescence due to a pencil beam excitation source. When literature values for the fluorescence quantum yield were used for each of the fluorophores, the fluorophore absorption coefficient (and hence concentration) at the excitation wavelengthwas recovered with a root-mean-square accuracy of 11.4% using the point source model of fluorescence and 8.0% using the more complicated pencil beam excitation model. The accuracy was calculated over a broad range of optical properties and fluorophore concentrations. The weighted difference of reflectance model performed poorly, with a root-mean-square error in concentration of about 50%. Monte Carlo simulations suggest that there are some situations where the weighted difference of reflectance is as accurate as the other two models, although this was not confirmed experimentally. Estimates of the fluorescence quantum yield in multiple scattering media were also made by determining independently from the fitted absorption spectrum and applying the various diffusion theory models. The fluorescence quantum yields for AlPcS{sub 4} and TPPS{sub 4} were calculated to be 0.59 {+-} 0.03 and 0.121 {+-} 0

  18. Measurement of fluorophore concentrations and fluorescence quantum yield in tissue-simulating phantoms using three diffusion models of steady-state spatially resolved fluorescence

    International Nuclear Information System (INIS)

    Diamond, Kevin R; Farrell, Thomas J; Patterson, Michael S

    2003-01-01

    Steady-state diffusion theory models of fluorescence in tissue have been investigated for recovering fluorophore concentrations and fluorescence quantum yield. Spatially resolved fluorescence, excitation and emission reflectance were calculated by diffusion theory and Monte Carlo simulations, and measured using a multi-fibre probe on tissue-simulating phantoms containing either aluminium phthalocyanine tetrasulfonate (AlPcS 4 ), Photofrin or meso-tetra-(4-sulfonatophenyl)-porphine dihydrochloride (TPPS 4 ). The accuracy of the fluorophore concentration and fluorescence quantum yield recovered by three different models of spatially resolved fluorescence were compared. The models were based on: (a) weighted difference of the excitation and emission reflectance, (b) fluorescence due to a point excitation source or (c) fluorescence due to a pencil beam excitation source. When literature values for the fluorescence quantum yield were used for each of the fluorophores, the fluorophore absorption coefficient (and hence concentration) at the excitation wavelengthwas recovered with a root-mean-square accuracy of 11.4% using the point source model of fluorescence and 8.0% using the more complicated pencil beam excitation model. The accuracy was calculated over a broad range of optical properties and fluorophore concentrations. The weighted difference of reflectance model performed poorly, with a root-mean-square error in concentration of about 50%. Monte Carlo simulations suggest that there are some situations where the weighted difference of reflectance is as accurate as the other two models, although this was not confirmed experimentally. Estimates of the fluorescence quantum yield in multiple scattering media were also made by determining independently from the fitted absorption spectrum and applying the various diffusion theory models. The fluorescence quantum yields for AlPcS 4 and TPPS 4 were calculated to be 0.59 ± 0.03 and 0.121 ± 0.001 respectively using the point

  19. Research of Digital Interface Layout Design based on Eye-tracking

    OpenAIRE

    Shao Jiang; Xue Chengqi; Wang Fang; Wang Haiyan; Tang Wencheng; Chen Mo; Kang Mingwu

    2015-01-01

    The aim of this paper is to improve the low service efficiency and unsmooth human-computer interaction caused by currently irrational layouts of digital interfaces for complex systems. Also, three common layout structures for digital interfaces are to be presented and five layout types appropriate for multilevel digital interfaces are to be summarized. Based on the eye tracking technology, an assessment was conducted in advantages and disadvantages of different layout types through subjects’ ...

  20. A combined approach of simulation and analytic hierarchy process in assessing production facility layouts

    Science.gov (United States)

    Ramli, Razamin; Cheng, Kok-Min

    2014-07-01

    One of the important areas of concern in order to obtain a competitive level of productivity in a manufacturing system is the layout design and material transportation system (conveyor system). However, changes in customers' requirements have triggered the need to design other alternatives of the manufacturing layout for existing production floor. Hence, this paper discusses effective alternatives of the process layout specifically, the conveyor system layout. Subsequently, two alternative designs for the conveyor system were proposed with the aims to increase the production output and minimize space allocation. The first proposed layout design includes the installation of conveyor oven in the particular manufacturing room based on priority, and the second one is the one without the conveyor oven in the layout. Simulation technique was employed to design the new facility layout. Eventually, simulation experiments were conducted to understand the performance of each conveyor layout design based on operational characteristics, which include predicting the output of layouts. Utilizing the Analytic Hierarchy Process (AHP), the newly and improved layout designs were assessed before the final selection was done. As a comparison, the existing conveyor system layout was included in the assessment process. Relevant criteria involved in this layout design problem were identified as (i) usage of space of each design, (ii) operator's utilization rates, (iii) return of investment (ROI) of the layout, and (iv) output of the layout. In the final stage of AHP analysis, the overall priority of each alternative layout was obtained and thus, a selection for final use by the management was made based on the highest priority value. This efficient planning and designing of facility layout in a particular manufacturing setting is able to minimize material handling cost, minimize overall production time, minimize investment in equipment, and optimize utilization of space.

  1. Rearrangement of the layout of the welding equipment of a company in the metal mechanical sector using the Systematic Layout Planning method (SLP

    Directory of Open Access Journals (Sweden)

    Silvio Alexsandro Turati

    2016-06-01

    Full Text Available The correct physical layout is relevant to the operational efficiency of the company. This study proposes rearranging the layout of the welding equipment of a company in the metal mechanical sector, which is located in Araras/SP, aiming to improve the production workflow. The Systematic Layout Planning method (SLP was used, with the field research divided into steps: obtaining detailed information about the process and the product; meetings with stakeholders; determining inter-related activities; analyzing space requirements; developing a new layout. The new layout has space allocated for the purchasing of new machinery, the existing machinery has been redistributed by specialty, and the unloading of raw materials has been transferred to the shed, maximizing the use of overhead cranes and keeping the stock close to the warehouse. In addition, forklift traffic flow has decreased; new movement corridors were demarcated; and painting areas were isolated. In conclusion, the SLP method proved efficient in creating a layout.

  2. 29 CFR 1926.752 - Site layout, site-specific erection plan and construction sequence.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Site layout, site-specific erection plan and construction... Steel Erection § 1926.752 Site layout, site-specific erection plan and construction sequence. (a... strength or sufficient strength to support the loads imposed during steel erection. (c) Site layout. The...

  3. A Novel DBC Layout for Current Imbalance Mitigation in SiC MOSFET Multichip Power Modules

    DEFF Research Database (Denmark)

    Li, Helong; Munk-Nielsen, Stig; Beczkowski, Szymon

    2016-01-01

    This letter proposes a novel direct bonded copper (DBC) layout for mitigating the current imbalance among the paralleled SiC MOSFET dies in multichip power modules. Compared to the traditional layout, the proposed DBC layout significantly reduces the circuit mismatch and current coupling effect...

  4. Typography and layout of technical reports - Survey of current practices

    Science.gov (United States)

    Pinelli, T. E.; Cordle, V. M.; Mccullough, R.

    1985-01-01

    As part of a review of the NASA Langley Research Center scientific and technical information program, 50 technical reports from industry, research institutions, and government agencies were systematically examined and analyzed to determine current usage and practice in regard to (1) typography, including composition method, type style, type size, and margin treatment; (2) graphic design, including layout and imposition of material on the page; and (3) physical media, including paper, ink, and binding methods. The results indicate that approximately 50 percent of the reports were typeset, 70 percent used Roman (serif) type, 80 percent used 10- or 11-point type for text, 60 percent used a ragged right-hand margin, slightly more than half used paragraph indentation, 75 percent used a single-column layout, 65 percent had one or more figures or tables placed perpendicular to (not aligned with) the text, and perfect binding was the most frequently used binding method.

  5. An UI Layout Files Analyzer for Test Data Generation

    Directory of Open Access Journals (Sweden)

    Paul POCATILU

    2014-01-01

    Full Text Available Prevention actions (trainings, audits and inspections (tests, validations, code reviews are the crucial factors in achieving a high quality level for any software application simply because low investments in this area are leading to significant expenses in terms of corrective actions needed for defect fixing. Mobile applications testing involves the use of various tools and scenarios. An important process is represented by test data generation. This paper proposes a test data generator (TDG system for mobile applications using several sources for test data and it focuses on the UI layout files analyzer module. The proposed architecture aims to reduce time-to-market for mobile applications. The focus is on test data generators based on the source code, user interface layout files (using markup languages like XML or XAML and application specifications. In order to assure a common interface for test data generators, an XML or JSON-based language called Data Specification Language (DSL is proposed.

  6. Analysis tools for the interplay between genome layout and regulation.

    Science.gov (United States)

    Bouyioukos, Costas; Elati, Mohamed; Képès, François

    2016-06-06

    Genome layout and gene regulation appear to be interdependent. Understanding this interdependence is key to exploring the dynamic nature of chromosome conformation and to engineering functional genomes. Evidence for non-random genome layout, defined as the relative positioning of either co-functional or co-regulated genes, stems from two main approaches. Firstly, the analysis of contiguous genome segments across species, has highlighted the conservation of gene arrangement (synteny) along chromosomal regions. Secondly, the study of long-range interactions along a chromosome has emphasised regularities in the positioning of microbial genes that are co-regulated, co-expressed or evolutionarily correlated. While one-dimensional pattern analysis is a mature field, it is often powerless on biological datasets which tend to be incomplete, and partly incorrect. Moreover, there is a lack of comprehensive, user-friendly tools to systematically analyse, visualise, integrate and exploit regularities along genomes. Here we present the Genome REgulatory and Architecture Tools SCAN (GREAT:SCAN) software for the systematic study of the interplay between genome layout and gene expression regulation. SCAN is a collection of related and interconnected applications currently able to perform systematic analyses of genome regularities as well as to improve transcription factor binding sites (TFBS) and gene regulatory network predictions based on gene positional information. We demonstrate the capabilities of these tools by studying on one hand the regular patterns of genome layout in the major regulons of the bacterium Escherichia coli. On the other hand, we demonstrate the capabilities to improve TFBS prediction in microbes. Finally, we highlight, by visualisation of multivariate techniques, the interplay between position and sequence information for effective transcription regulation.

  7. Impact of risk analysis on ITER nuclear buildings layout

    International Nuclear Information System (INIS)

    Sabathe, Laurent; Lignini, Franck; Rodriguez-Rodrigo, Lina; Uzan-Elbez, Joelle; Girard, Jean-Philippe

    2007-01-01

    The internal layout of ITER nuclear buildings (Tokamak, Tritium, Hot cell and Radwaste buildings) is the result of an iterative process. Notwithstanding civil engineering requirements, technical and functional requirements for the processes housed in the buildings, the internal layout must also take into account safety requirements and workers protection requirements in normal, incidental and accidental conditions. Potential hazards and constraints result in the definition of various zonings. Each room is classified depending on the level of the risks induced by normal and incidental or accidental conditions: - radiological exposure to tritium, and activated products → radiological zoning; - exposure to beryllium (vacuum vessel blankets) → beryllium zoning; - exposure to electromagnetic fields during plasma shots → electromagnetic zoning; - fire hazard: fire compartmentalization; ·explosion hazard: anti-blast zoning; - waste treatment → waste zoning. Prevention of common mode failure due to internal hazards (fire, flooding, load drop...) for redundant safety important components is also taken into account by geographical separation or by installation of protections between components (either in the same room or preferably when possible by segregation in different rooms). The designer has also taken into account access requirements to equipments and circulation rules for personal, material and substances in ITER nuclear buildings. Risk analyses are performed in the Preliminary Safety Report in order to demonstrate that the layout of ITER nuclear buildings allows meeting the safety objectives and takes into account the requirements associated with the zonings classifications and complies with the regulation. When necessary, modifications are implemented in the design. For example, recent layout modifications are been studied in the tritium building: utility rooms (electrical supply) were transferred outside the radiological hazard zones. A direct access from

  8. Impact of risk analysis on ITER nuclear buildings internal layout

    International Nuclear Information System (INIS)

    Lignini, F.; Sabathe, L.; Rodriguez-Rodrigo, L.; Uzan-Elbez, J.; Girard, J.-P.

    2006-01-01

    The internal layout of ITER nuclear buildings (Tokamak, Tritium, Hot cell and Radwaste buildings) is the result of an iterative process. Notwithstanding civil engineering requirements, technical and functional requirements for the processes housed in the buildings, the internal layout must also take into account safety requirements and workers protection requirements in normal, incidental and accidental conditions. Potential hazards and constraints result in the definition of various zonings. Each room is classified depending on the level of risk induced by normal and incidental or accidental conditions : - radiological exposure to tritium, and activated products → radiological zoning - exposure to beryllium (vacuum vessel blankets) → beryllium zoning - exposure to electromagnetic fields during plasma shots → electromagnetic zoning - fire hazard : fire compartmentalisation - explosion hazard → anti-blast zoning - waste treatment → waste zoning Prevention of common mode failure due to internal hazards (fire, flooding, load drop ...) for redundant safety important components is also taken into account by geographical separation or by installation of protections between components (either in the same room or preferably when possible by segregation in different rooms). The designer also has to take into account access requirements to equipment and circulation rules for personal, material and substances in ITER nuclear buildings. Risk analyses are performed in the Preliminary Safety Report in order to demonstrate that the layout of ITER nuclear buildings allows to meet the safety objectives and takes into account the requirements associated with the zonings classifications and complies with the regulation. When necessary, modifications are implemented in the design. For example, recent layout modifications were included in the tritium building : utility rooms (electrical supply) were transferred outside the radiological hazard zones. A direct access from the

  9. Nuclear island buildings layout collaborative design platform development and application

    International Nuclear Information System (INIS)

    Chen Li; Huang Wenqiang

    2014-01-01

    Based on characteristics of nuclear island layout design, the large number files and complicated interface, for realizing collaborative design and fine management goal, Establish collaborative design platform, which includes the design task module, 3D design module, project management module. These three modules can package design input files, realize synchronous design and real-time track design drawings state, timely feedback between design, procurement, construction site. There is no design task delay due to tracking and has realized fine management of design. (authors)

  10. Doublet vs. FODO structure: beam dynamics and layout

    CERN Document Server

    Eshraqi, M; CERN. Geneva. BE Department

    2010-01-01

    A FoDo (singlet) structure is designed for the CERN Superconducting Proton LINAC. This architecture is compared to the baseline (doublet) architecture of SPL on the basis of its beam dynamics performance and the required investment. The sensitivity of both layouts to quadrupole gradient errors and misalignment is checked and a correction scheme for beam steering is proposed. Finally a single quad beam dilution scheme is studied and designed for the pilot beam dump.

  11. Study of site layout in the Rokkasho site

    International Nuclear Information System (INIS)

    Sato, Kazuyoshi; Tamura, Kousaku; Yagenji, Akira; Sekiya, Shigeki; Takahashi, Hideo; Neyatani, Yuzuru; Uehara, Masaharu; Motohashi, Keiichi; Hashimoto, Masayoshi; Ogino, Shunji; Nagamatsu, Nobuhide

    2006-03-01

    The Final Design Report (FDR) of the International Thermonuclear Experimental Reactor (ITER) was published on July 2001 as a summary of the Engineering Design Activity (EDA). After the EDA, site dependent design has been investigated for the invitation of ITER toward Rokkasho Site (Iyasakadai area) in Aomori prefecture. This report describes the results of site layout of major buildings and structures of ITER in the Rokkasho-Site. The data of the ground near the site and the results of site dependent design in Japan were applied to this study. Through this study, the most appropriate site layout has been constructed with satisfaction of following conditions. (1) Bedrock level at the tokamak complex building is relatively high and it can be reduced the cost of excavation and foundation work. (2) Total amount of excavation soil for site preparation is minimized and the flexibility of the layout is ensured with flat ground level. (3) Accessibility of human and equipments, reduction of noise and vibration to the environment can be obtained. Total length of ducts and piping between buildings in site is minimized. (author)

  12. Camera Layout Design for the Upper Stage Thrust Cone

    Science.gov (United States)

    Wooten, Tevin; Fowler, Bart

    2010-01-01

    Engineers in the Integrated Design and Analysis Division (EV30) use a variety of different tools to aid in the design and analysis of the Ares I vehicle. One primary tool in use is Pro-Engineer. Pro-Engineer is a computer-aided design (CAD) software that allows designers to create computer generated structural models of vehicle structures. For the Upper State thrust cone, Pro-Engineer was used to assist in the design of a layout for two camera housings. These cameras observe the separation between the first and second stage of the Ares I vehicle. For the Ares I-X, one standard speed camera was used. The Ares I design calls for two separate housings, three cameras, and a lighting system. With previous design concepts and verification strategies in mind, a new layout for the two camera design concept was developed with members of the EV32 team. With the new design, Pro-Engineer was used to draw the layout to observe how the two camera housings fit with the thrust cone assembly. Future analysis of the camera housing design will verify the stability and clearance of the camera with other hardware present on the thrust cone.

  13. CiSE: a circular spring embedder layout algorithm.

    Science.gov (United States)

    Dogrusoz, Ugur; Belviranli, Mehmet E; Dilek, Alptug

    2013-06-01

    We present a new algorithm for automatic layout of clustered graphs using a circular style. The algorithm tries to determine optimal location and orientation of individual clusters intrinsically within a modified spring embedder. Heuristics such as reversal of the order of nodes in a cluster and swap of neighboring node pairs in the same cluster are employed intermittently to further relax the spring embedder system, resulting in reduced inter-cluster edge crossings. Unlike other algorithms generating circular drawings, our algorithm does not require the quotient graph to be acyclic, nor does it sacrifice the edge crossing number of individual clusters to improve respective positioning of the clusters. Moreover, it reduces the total area required by a cluster by using the space inside the associated circle. Experimental results show that the execution time and quality of the produced drawings with respect to commonly accepted layout criteria are quite satisfactory, surpassing previous algorithms. The algorithm has also been successfully implemented and made publicly available as part of a compound and clustered graph editing and layout tool named CHISIO.

  14. Coherent image layout using an adaptive visual vocabulary

    Science.gov (United States)

    Dillard, Scott E.; Henry, Michael J.; Bohn, Shawn; Gosink, Luke J.

    2013-03-01

    When querying a huge image database containing millions of images, the result of the query may still contain many thousands of images that need to be presented to the user. We consider the problem of arranging such a large set of images into a visually coherent layout, one that places similar images next to each other. Image similarity is determined using a bag-of-features model, and the layout is constructed from a hierarchical clustering of the image set by mapping an in-order traversal of the hierarchy tree into a space-filling curve. This layout method provides strong locality guarantees so we are able to quantitatively evaluate performance using standard image retrieval benchmarks. Performance of the bag-of-features method is best when the vocabulary is learned on the image set being clustered. Because learning a large, discriminative vocabulary is a computationally demanding task, we present a novel method for efficiently adapting a generic visual vocabulary to a particular dataset. We evaluate our clustering and vocabulary adaptation methods on a variety of image datasets and show that adapting a generic vocabulary to a particular set of images improves performance on both hierarchical clustering and image retrieval tasks.

  15. Lower-Temperature Subsurface Layout and Ventilation Concepts

    International Nuclear Information System (INIS)

    Christine L. Linden; Edward G. Thomas

    2001-01-01

    This analysis combines work scope identified as subsurface facility (SSF) low temperature (LT) Facilities System and SSF LT Ventilation System in the Technical Work Plan for Subsurface Design Section FY 01 Work Activities (CRWMS M and O 2001b, pp. 6 and 7, and pp. 13 and 14). In accordance with this technical work plan (TWP), this analysis is performed using AP-3.10Q, Analyses and Models. It also incorporates the procedure AP-SI.1Q, Software Management. The purpose of this analysis is to develop an overall subsurface layout system and the overall ventilation system concepts that address a lower-temperature operating mode for the Monitored Geologic Repository (MGR). The objective of this analysis is to provide a technical design product that supports the lower-temperature operating mode concept for the revision of the system description documents and to provide a basis for the system description document design descriptions. The overall subsurface layout analysis develops and describes the overall subsurface layout, including performance confirmation facilities (also referred to as Test and Evaluation Facilities) for the Site Recommendation design. This analysis also incorporates current program directives for thermal management

  16. CFD Investigation of the effects of bubble aerator layouts on hydrodynamics of an activated sludge channel reactor.

    Science.gov (United States)

    Hreiz, Rainier; Potier, Olivier; Wicks, Jim; Commenge, Jean-Marc

    2018-03-08

    In this paper, computational fluid dynamics (CFD) simulations are employed to characterize the effects of bubble aerator layouts (i.e. spatial arrangement) on the hydrodynamics in activated sludge (AS) reactors. The first configuration considered is a channel reactor with aerators placed alongside one lateral wall, for which velocity measurements are available in literature. CFD results were in good agreement with experimental data, which proves that the model is sufficiently accurate and predictive. Accordingly, simulations and numerical residence time distribution tests were conducted for different aerator layouts to determine their effects on the reactor hydrodynamics. The results revealed that the flow characteristics are extremely sensitive to the aerators arrangement given the high gas flow rates used in AS processes. Among the layouts investigated, the one where diffusers are placed all over the reactor floor has led to the least dispersive flow, i.e. which characteristics best tend toward that of an ideal plug flow reactor. Indeed, this flow field presented the lowest average turbulent diffusion and the most uniform axial velocity and turbulence fields. Such a flow behaviour is expected to be highly beneficial for biological treatment since it reduces pollutant dilution by axial diffusion and limits raw wastewater channelling to the outlet.

  17. A Novel DBC Layout for Current Imbalance Mitigation in SiC MOSFET Multichip Power Modules

    DEFF Research Database (Denmark)

    Li, Helong; Munk-Nielsen, Stig; Beczkowski, Szymon

    2016-01-01

    This paper proposes a novel Direct Bonded Copper (DBC) layout for mitigating the current imbalance among the paralleled SiC MOSFET dies in multichip power modules. Compared to the traditional layout, the proposed DBC layout significantly reduces the circuit mismatch and current coupling effect......, which consequently improves the current sharing among the paralleled SiC MOSFET dies in power module. Mathematic analysis and circuit model of the DBC layout are presented to elaborate on the superior features of the proposed DBC layout. Simulation and experimental results further verify the theoretical...

  18. Research of Digital Interface Layout Design based on Eye-tracking

    Directory of Open Access Journals (Sweden)

    Shao Jiang

    2015-01-01

    Full Text Available The aim of this paper is to improve the low service efficiency and unsmooth human-computer interaction caused by currently irrational layouts of digital interfaces for complex systems. Also, three common layout structures for digital interfaces are to be presented and five layout types appropriate for multilevel digital interfaces are to be summarized. Based on the eye tracking technology, an assessment was conducted in advantages and disadvantages of different layout types through subjects’ search efficiency. Based on data and results, this study constructed a matching model which is appropriate for multilevel digital interface layout and verified the fact that the task element is a significant and important aspect of layout design. A scientific experimental model of research on digital interfaces for complex systems is provided. Both data and conclusions of the eye movement experiment provide a reference for layout designs of interfaces for complex systems with different task characteristics.

  19. Caracterização do microclima dos diferentes layouts de caixas no transporte de ovos férteis Characterization of microclimate in different layout of boxes during transport of fertile eggs

    Directory of Open Access Journals (Sweden)

    Aérica C. Nazareno

    2013-03-01

    Full Text Available Quando as condições microclimáticas e de transporte são combinadas inadequadamente, os componentes dos ovos férteis podem ser danificados. Objetivou-se, com este trabalho, caracterizar e analisar a dependência espacial dos perfis microclimáticos no transporte de ovos férteis em diferentes layouts de caixas. A pesquisa foi conduzida na empresa integradora avícola, em Mogi Mirim, SP, por meio do acompanhamento de cinco carregamentos. Utilizou-se um caminhão climatizado do tipo baú, com capacidade para 592 caixas de ovos e se avaliaram dois layouts da carga (caixas superiores e inferiores de 9 pilhas com seis caixas de ovos férteis. Um microprocessador foi instalado dentro das caixas de ovos, totalizando 18 microprocessadores. As variáveis meteorológicas analisadas foram: temperatura (ºC umidade relativa (% e entalpia específica (kJ kg-1 ar seco. O delineamento experimental adotado foi o inteiramente casualizado com parcelas subdividas e realizada a análise geoestatística (krigagem ordinária. No layout das caixas superiores foram registrados valores elevados de temperatura e baixos valores de umidade relativa e entalpia específica. As regiões de piores condições microclimáticas nos dois layouts se situaram nas partes central e traseira do caminhão, durante o transporte dos ovos férteis.The fertile egg components may be damaged when the microclimatic conditions and transportation characteristics are combined inadequately. Thus, the aim of this study was to characterize and to assess the spatial dependence of microclimatic profiles during transport of fertile eggs with different layout of boxes. A trial was conducted in a commercial poultry industry in Mogi Mirim in the State of São Paulo, Brazil, through monitoring five loads of hatching eggs. An air conditioned truck was used, with maximum capacity of 592 egg boxes. Two layout of boxes were assessed in the present study. One data logger was installed inside the egg boxes

  20. Wendelstein 7-X Torus Hall Layout and System Integration

    International Nuclear Information System (INIS)

    Hartmann, D.; Damiani, C.; Hartfuss, H.-J.; Krampitz, R.; Neuner, U.

    2006-01-01

    Wendelstein 7-X is an experimental fusion device presently under construction in Greifswald, Germany, to study the stellarator concept at reactor relevant parameters und steady-state conditions. The heart of the machine consists of the torus that houses the superconducting coils and the plasma vacuum vessel. It is located nearly in the center of a 30 m x 30 m x 20 m hall. A large number of components need to be placed in close proximity of the torus to provide the system with the required means, e.g. cryogenic gases, cooling water, electricity, and to integrate it with the peripheral diagnostic and heating components. The arrangement of these components has to be supported by suitable structures, and has to be optimized to allow for installation, maintenance, and repair. In addition, space has to be provided for escape routes and for sufficient distance between components that could negatively influence each other's performance, etc. The layout of the components has been done over many years using 3D CAD software. It was based on simple geometric models of the components and of the additionally required space. Presently the layout design is being detailed and updated by replacing the original coarse models with more refined estimates or - in some cases - with as-built models. All interface requirements are carefully taken into account. Detailed routing was specified for the cryo and cooling water supply lines whose design and installation is outsourced. Due to the limited space available and severely restricted access during experimental campaigns, the requirement to put auxiliary components like electronic racks into the torus hall is being queried. The paper summarizes the present state of the component layout in the torus hall, and how the peripheral supply, diagnostics, and heating systems are integrated into the machine. (author)

  1. [Land layout for lake tourism based on ecological restraint].

    Science.gov (United States)

    Wang, Jian-Ying; Li, Jiang-Feng; Zou, Li-Lin; Liu, Shi-Bin

    2012-10-01

    To avoid the decrease and deterioration of lake wetlands and the other ecological issues such as lake water pollution that were caused by the unreasonable exploration of lake tourism, a land layout for the tourism development of Liangzi Lake with the priority of ecological security pattern was proposed, based on the minimal cumulative resistance model and by using GIS technology. The study area was divided into four ecological function zones, i. e., core protection zone, ecological buffer zone, ecotone zone, and human activity zone. The core protection zone was the landscape region of ecological source. In the protection zone, new tourism land was forbidden to be increased, and some of the existing fundamental tourism facilities should be removed while some of them should be upgraded. The ecological buffer zone was the landscape region with resistance value ranged from 0 to 4562. In the buffer zone, expansion of tourism land should be forbidden, the existing tourism land should be downsized, and human activities should be isolated from ecological source by converting the human environment to the natural environment as far as possible. The ecotone zone was the landscape region with resistance value ranged from 4562 to 30797. In this zone, the existing tourism land was distributed in patches, tourism land could be expanded properly, and the lake forestry ecological tourism should be developed widely. The human activity zone was the landscape region with resistance value ranged from 30797 to 97334, which would be the key area for the land layout of lake tourism. It was suggested that the land layout for tourism with the priority of landscape ecological security pattern would be the best choice for the lake sustainable development.

  2. Wind conditions in urban layout - Numerical and experimental research

    Science.gov (United States)

    Poćwierz, Marta; Zielonko-Jung, Katarzyna

    2018-01-01

    This paper presents research which compares the numerical and the experimental results for different cases of airflow around a few urban layouts. The study is concerned mostly with the analysis of parameters, such as pressure and velocity fields, which are essential in the building industry. Numerical simulations have been performed by the commercial software Fluent, with the use of a few different turbulence models, including popular k-ɛ, k-ɛ realizable or k-ω. A particular attention has been paid to accurate description of the conditions on the inlet and the selection of suitable computing grid. The pressure measurement near buildings and oil visualization were undertaken and described accordingly.

  3. The Influence of Classroom Layout on Children's English Learning Development

    Institute of Scientific and Technical Information of China (English)

    林琬媚

    2016-01-01

    Nowadays, more and more Children English Training organization developed, all the parents and teachers also want to improve the children's English. So the parents will find the organization where the teachers are better in teaching. They will motive a lot of imagine and acquire many information which you can not know. If we can care more about this point from the children, may be it also can help children to learn English well. This essay aims at how does classroom Layout influence the children to learn English well and let the children love this environment.

  4. Automated Layout Generation of Analogue and Mixed-Signal ASIC's

    DEFF Research Database (Denmark)

    Bloch, Rene

    search for better solutions can be guided into new and more prosperous areas of the search space. This feature also provides the designer with the ability to easily try out several implementation options, thus exploring the solution space, which are especially important in the early stages of the design...... is generated using a full-custom layout style and is based on a library of CMOS process independent device generators. The placement for the analogue circuit is derived using the interactive floorplan optimization algorithm described above. This ensures that a high degree of user control is implemented...

  5. Energy efficient LED layout optimization for near-uniform illumination

    Science.gov (United States)

    Ali, Ramy E.; Elgala, Hany

    2016-09-01

    In this paper, we consider the problem of designing energy efficient light emitting diodes (LEDs) layout while satisfying the illumination constraints. Towards this objective, we present a simple approach to the illumination design problem based on the concept of the virtual LED. We formulate a constrained optimization problem for minimizing the power consumption while maintaining a near-uniform illumination throughout the room. By solving the resulting constrained linear program, we obtain the number of required LEDs and the optimal output luminous intensities that achieve the desired illumination constraints.

  6. Layout-aware text extraction from full-text PDF of scientific articles.

    Science.gov (United States)

    Ramakrishnan, Cartic; Patnia, Abhishek; Hovy, Eduard; Burns, Gully Apc

    2012-05-28

    The Portable Document Format (PDF) is the most commonly used file format for online scientific publications. The absence of effective means to extract text from these PDF files in a layout-aware manner presents a significant challenge for developers of biomedical text mining or biocuration informatics systems that use published literature as an information source. In this paper we introduce the 'Layout-Aware PDF Text Extraction' (LA-PDFText) system to facilitate accurate extraction of text from PDF files of research articles for use in text mining applications. Our paper describes the construction and performance of an open source system that extracts text blocks from PDF-formatted full-text research articles and classifies them into logical units based on rules that characterize specific sections. The LA-PDFText system focuses only on the textual content of the research articles and is meant as a baseline for further experiments into more advanced extraction methods that handle multi-modal content, such as images and graphs. The system works in a three-stage process: (1) Detecting contiguous text blocks using spatial layout processing to locate and identify blocks of contiguous text, (2) Classifying text blocks into rhetorical categories using a rule-based method and (3) Stitching classified text blocks together in the correct order resulting in the extraction of text from section-wise grouped blocks. We show that our system can identify text blocks and classify them into rhetorical categories with Precision1 = 0.96% Recall = 0.89% and F1 = 0.91%. We also present an evaluation of the accuracy of the block detection algorithm used in step 2. Additionally, we have compared the accuracy of the text extracted by LA-PDFText to the text from the Open Access subset of PubMed Central. We then compared this accuracy with that of the text extracted by the PDF2Text system, 2commonly used to extract text from PDF. Finally, we discuss preliminary error analysis for

  7. Layout-aware text extraction from full-text PDF of scientific articles

    Directory of Open Access Journals (Sweden)

    Ramakrishnan Cartic

    2012-05-01

    Full Text Available Abstract Background The Portable Document Format (PDF is the most commonly used file format for online scientific publications. The absence of effective means to extract text from these PDF files in a layout-aware manner presents a significant challenge for developers of biomedical text mining or biocuration informatics systems that use published literature as an information source. In this paper we introduce the ‘Layout-Aware PDF Text Extraction’ (LA-PDFText system to facilitate accurate extraction of text from PDF files of research articles for use in text mining applications. Results Our paper describes the construction and performance of an open source system that extracts text blocks from PDF-formatted full-text research articles and classifies them into logical units based on rules that characterize specific sections. The LA-PDFText system focuses only on the textual content of the research articles and is meant as a baseline for further experiments into more advanced extraction methods that handle multi-modal content, such as images and graphs. The system works in a three-stage process: (1 Detecting contiguous text blocks using spatial layout processing to locate and identify blocks of contiguous text, (2 Classifying text blocks into rhetorical categories using a rule-based method and (3 Stitching classified text blocks together in the correct order resulting in the extraction of text from section-wise grouped blocks. We show that our system can identify text blocks and classify them into rhetorical categories with Precision1 = 0.96% Recall = 0.89% and F1 = 0.91%. We also present an evaluation of the accuracy of the block detection algorithm used in step 2. Additionally, we have compared the accuracy of the text extracted by LA-PDFText to the text from the Open Access subset of PubMed Central. We then compared this accuracy with that of the text extracted by the PDF2Text system, 2commonly used to extract text from PDF

  8. Effects of Optimizing the Scan-Path on Scanning Keyboards with QWERTY-Layout for English Text.

    Science.gov (United States)

    Sandnes, Frode Eika; Medola, Fausto Orsi

    2017-01-01

    Scanning keyboards can be essential tools for individuals with reduced motor function. However, most research addresses layout optimization. Learning new layouts is time-consuming. This study explores the familiar QWERTY layout with alternative scanning paths intended for English text. The results show that carefully designed scan-paths can help QWERTY nearly match optimized layouts in performance.

  9. High-Quality Ultra-Compact Grid Layout of Grouped Networks.

    Science.gov (United States)

    Yoghourdjian, Vahan; Dwyer, Tim; Gange, Graeme; Kieffer, Steve; Klein, Karsten; Marriott, Kim

    2016-01-01

    Prior research into network layout has focused on fast heuristic techniques for layout of large networks, or complex multi-stage pipelines for higher quality layout of small graphs. Improvements to these pipeline techniques, especially for orthogonal-style layout, are difficult and practical results have been slight in recent years. Yet, as discussed in this paper, there remain significant issues in the quality of the layouts produced by these techniques, even for quite small networks. This is especially true when layout with additional grouping constraints is required. The first contribution of this paper is to investigate an ultra-compact, grid-like network layout aesthetic that is motivated by the grid arrangements that are used almost universally by designers in typographical layout. Since the time when these heuristic and pipeline-based graph-layout methods were conceived, generic technologies (MIP, CP and SAT) for solving combinatorial and mixed-integer optimization problems have improved massively. The second contribution of this paper is to reassess whether these techniques can be used for high-quality layout of small graphs. While they are fast enough for graphs of up to 50 nodes we found these methods do not scale up. Our third contribution is a large-neighborhood search meta-heuristic approach that is scalable to larger networks.

  10. Comparative study T-type and I-type layout of PWR nuclear power plants

    International Nuclear Information System (INIS)

    Eko Rudi Iswanto and Siti Alimah

    2010-01-01

    Determining plant layout is one of the five major stages during the life time of a nuclear power plant. Some important factors that affect in the selecting of plant layout are availability of infrastructure, economic aspects, social aspects, public and environment safety, and also easy to do. Another factor to be considered is requirements as seismic design, which refers to the principles of good security workers, communities and the environment of radiological risks. There are many layout types of nuclear power plant, two of them are T-type layout and I-type layout. Each type of the plant layout has advantage and disadvantage, therefore this study is to understand them. Good layout is able to provide a high level of security against earthquakes. In term of earthquake design, I-type layout has a higher security level than T-type layout. Therefore, I-type layout can be a good choice for PWR nuclear power plants 1000 MWe that will be built in Indonesia. (author)

  11. Three-dimensional volumetric MRI with isotropic resolution: improved speed of acquisition, spatial resolution and assessment of lesion conspicuity in patients with recurrent soft tissue sarcoma

    Energy Technology Data Exchange (ETDEWEB)

    Ahlawat, Shivani [The Johns Hopkins Medical Institutions, The Russell H. Morgan Department of Radiology and Radiological Science, Baltimore, MD (United States); Morris, Carol [The Johns Hopkins Medical Institutions, Department of Orthopedic Surgery, Baltimore, MD (United States); The Johns Hopkins Medical Institutions, Department of Oncology, Baltimore, MD (United States); Fayad, Laura M. [The Johns Hopkins Medical Institutions, The Russell H. Morgan Department of Radiology and Radiological Science, Baltimore, MD (United States); The Johns Hopkins Medical Institutions, Department of Orthopedic Surgery, Baltimore, MD (United States); The Johns Hopkins Medical Institutions, Department of Oncology, Baltimore, MD (United States)

    2016-05-15

    To assess the acquisition speed, lesion conspicuity, and inter-observer agreement associated with volumetric T{sub 1}-weighted MR sequences with isotropic resolution for detecting recurrent soft-tissue sarcoma (STS). Fifteen subjects with histologically proven recurrent STS underwent MRI, including axial and coronal T{sub 1}-weighted spin echo (T{sub 1}-WSE) (5-mm slice thickness) and coronal 3D volumetric T{sub 1}-weighted (fat-suppressed, volume-interpolated, breath-hold examination; repetition time/echo time, 3.7/1.4 ms; flip angle, 9.5 ; 1-mm slice thickness) sequences before and after intravenous contrast administration. Subtraction imaging and multiplanar reformations (MPRs) were performed. Acquisition times for T{sub 1}-WSE in two planes and 3D sequences were reported. Two radiologists reviewed images for quality (>50 % artifacts, 25-50 % artifacts, <25 % artifacts, and no substantial artifacts), lesion conspicuity, contrast-to-noise ratio (CNR{sub muscle}), recurrence size, and recurrence-to-joint distance. Descriptive and intraclass correlation (ICC) statistics are given. Mean acquisition times were significantly less for 3D imaging compared with 2-plane T{sub 1}-WSE (183.6 vs 342.6 s; P = 0.012). Image quality was rated as having no substantial artifacts in 13/15 and <25 % artifacts in 2/15. Lesion conspicuity was significantly improved for subtracted versus unsubtracted images (CNR{sub muscle}, 100 ± 138 vs 181 ± 199; P = 0.05). Mean recurrent lesion size was 2.5 cm (range, 0.7-5.7 cm), and measurements on 3D sequences offered excellent interobserver agreement (ICC, 0.98 for lesion size and 0.96 for recurrence-to-joint distance with MPR views). Three-dimensional volumetric sequences offer faster acquisition times, higher spatial resolution, and MPR capability compared with 2D T{sub 1}-WSE for postcontrast imaging. Subtraction imaging provides higher lesion conspicuity for detecting recurrent STS in skeletal muscle, with excellent interobserver

  12. Neonatal Intensive Care Unit Layout and Nurses' Work.

    Science.gov (United States)

    Doede, Megan; Trinkoff, Alison M; Gurses, Ayse P

    2018-01-01

    Neonatal intensive care units (NICUs) remain one of the few areas in hospitals that still use an open bay (OPBY) design for patient stays greater than 24 hr, housing multiple infants, staff, and families in one large room. This creates high noise levels, contributes to the spread of infection, and affords families little privacy. These problems have given rise to the single-family room NICU. This represents a significant change in the care environment for nurses. This literature review answers the question: When compared to OPBY layout, how does a single family room layout impact neonatal nurses' work? Thirteen studies published between 2006 and 2015 were located. Many studies reported both positive and negative effects on nurses' work and were therefore sorted by their cited advantages and disadvantages. Advantages included improved quality of the physical environment; improved quality of patient care; improved parent interaction; and improvements in nurse job satisfaction, stress, and burnout. Disadvantages included decreased interaction among the NICU patient care team, increased nurse workload, decreased visibility on the unit, and difficult interactions with family. This review suggests that single-family room NICUs introduce a complex situation in which trade-offs occur for nurses, most prominently the trade-off between visibility and privacy. Additionally, the literature is clear on what elements of nurses' work are impacted, but how the built environment influences these elements, and how these elements interact during nurses' work, is not as well understood. The current level of research and directions for future research are also discussed.

  13. Methodologies for optimizing ROP detector layout for CANDU (registered) reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kastanya, Doddy, E-mail: kastanyd@aecl.c [Reactor Core Physics Branch, Atomic Energy of Canada Limited, 2251 Speakman Drive, Mississauga, ON, L5K 1B2 (Canada); Caxaj, Victor [Reactor Core Physics Branch, Atomic Energy of Canada Limited, 2251 Speakman Drive, Mississauga, ON, L5K 1B2 (Canada)

    2011-01-15

    The regional overpower protection (ROP) systems protect CANDU (registered) reactors against overpower in the fuel that would reduce the safety margin-to-dryout. Both a localized power peaking within the core (for example, as a result of certain reactivity device configuration) or a general increase in the core power level during a slow-loss-of-regulation (SLOR) event could cause overpower in the fuel. This overpower could lead to fuel sheath dryout. In the CANDU (registered) 600 MW (CANDU 6) design, there are two ROP systems in the core, one for each fast-acting shutdown systems. Each ROP system includes a number of fast-responding, self-powered flux detectors suitably distributed throughout the core within vertical and horizontal assemblies. Traditionally, the placement of these detectors was done using a method called the detector layout optimization (DLO). A new methodology for designing the detector layout for the ROP system has been developed recently. The new method, called the DETPLASA algorithm, utilizes the simulated annealing (SA) technique to optimize the placement of the detectors in the core. Both methodologies will be discussed in detail in this paper. Numerical examples are employed to better illustrate how each method works. Results from some sensitivity studies on three SA parameters are also presented.

  14. The Layout of Power and Space in Jingdezhen Imperial Factory

    Directory of Open Access Journals (Sweden)

    Zhan Jia

    2014-12-01

    Full Text Available This paper, by referring to the archaeological reports and local gazetteers and comparing images of porcelain wares, makes a comprehensive and in-depth analysis of the layout of power and space in Jingdezhen Imperial Factory according to its geography, geomancy, security management, space regulation, architectural features, production characteristics and production layout. It contends that the Imperial Factory which integrates porcelain making factory with local government is the embodiment of absolute monarchy in ceramic culture. The factory is located on Zhushan mountain, the center of Jingdezhen’s industry, business and transportation. Being at the center, it gives off an air of prestige and majesty, overlooking dominantly the surrounding private kilns. It has also turned the political system into power operation, setting up not only workshops but also administrative offices. By taking advantage of the best resources, it has produced porcelain for imperial family and court. Its specialized production has solved the contradiction between complicated technology and numerous procedures of production. The shape, color and pattern of the porcelain wares are strictly stipulated and the best of the best wares are demanded. Hence the porcelain production is featured with longest firing, largest scale, superb craftsmanship, and best kinds of wares. All of these reveal the process and rule power and space are intersected and different cultures overlapped.

  15. ForceAtlas2, a continuous graph layout algorithm for handy network visualization designed for the Gephi software.

    Science.gov (United States)

    Jacomy, Mathieu; Venturini, Tommaso; Heymann, Sebastien; Bastian, Mathieu

    2014-01-01

    Gephi is a network visualization software used in various disciplines (social network analysis, biology, genomics...). One of its key features is the ability to display the spatialization process, aiming at transforming the network into a map, and ForceAtlas2 is its default layout algorithm. The latter is developed by the Gephi team as an all-around solution to Gephi users' typical networks (scale-free, 10 to 10,000 nodes). We present here for the first time its functioning and settings. ForceAtlas2 is a force-directed layout close to other algorithms used for network spatialization. We do not claim a theoretical advance but an attempt to integrate different techniques such as the Barnes Hut simulation, degree-dependent repulsive force, and local and global adaptive temperatures. It is designed for the Gephi user experience (it is a continuous algorithm), and we explain which constraints it implies. The algorithm benefits from much feedback and is developed in order to provide many possibilities through its settings. We lay out its complete functioning for the users who need a precise understanding of its behaviour, from the formulas to graphic illustration of the result. We propose a benchmark for our compromise between performance and quality. We also explain why we integrated its various features and discuss our design choices.

  16. Aircraft Cockpit Ergonomic Layout Evaluation Based on Uncertain Linguistic Multiattribute Decision Making

    Directory of Open Access Journals (Sweden)

    Junxuan Chen

    2014-03-01

    Full Text Available In the view of the current cockpit information interaction, facilities and other characteristics are increasingly multifarious; the early layout evaluation methods based on single or partial components, often cause comprehensive evaluation unilateral, leading to the problems of long development period and low efficiency. Considering the fuzziness of ergonomic evaluation and diversity of evaluation information attributes, we refine and build an evaluation system based on the characteristics of the current cockpit man-machine layout and introduce the different types of uncertain linguistic multiple attribute combination decision making (DTULDM method in the cockpit layout evaluation process. Meanwhile, we also establish an aircraft cockpit ergonomic layout evaluation model. Finally, an experiment about cockpit layout evaluation is given, and the result demonstrates that the proposed method about cockpit ergonomic layout evaluation is feasible and effective.

  17. Incorporating Workflow Interference in Facility Layout Design: The Quartic Assignment Problem

    OpenAIRE

    Wen-Chyuan Chiang; Panagiotis Kouvelis; Timothy L. Urban

    2002-01-01

    Although many authors have noted the importance of minimizing workflow interference in facility layout design, traditional layout research tends to focus on minimizing the distance-based transportation cost. This paper formalizes the concept of workflow interference from a facility layout perspective. A model, formulated as a quartic assignment problem, is developed that explicitly considers the interference of workflow. Optimal and heuristic solution methodologies are developed and evaluated.

  18. Research on Layout Optimization of Urban Circle Solid Waste Transfer and Disposal Stations

    OpenAIRE

    Xuhui Li; Gangyan Li; Guowen Sun; Huiping Shi; Bao’an Yang

    2013-01-01

    Based on the Systematic Layout Planning theory and the analysis of transfer stations’ technological processes, a layout optimization model for solid waste transfer and disposal stations was made. The operating units’ layout of the solid waste transfer and disposal stations was simulated and optimized using the genetic algorithm, which could achieve reasonable technological processes, the smallest floor space and the lowest construction cost. The simulation result can also direct t...

  19. Study on comprehensive evaluation model for nuclear power plant control room layout

    International Nuclear Information System (INIS)

    Zhu Yiming; Liu Yuan; Fan Huixian

    2010-01-01

    A comprehensive evaluation model for layout of the main control room of nuclear power plants was proposed. Firstly the design scope and principle for the layout of the main control room were defined based on the standards, and then the index system for the comprehensive evaluation was established. Finally, comprehensive evaluation was carried out for the layout design by applying the fuzzy comprehensive evaluation method in the index system. (authors)

  20. Calculation of calibration factors and layout criteria for gamma scanning of waste drums from nuclear plants

    International Nuclear Information System (INIS)

    Inder Schmitten, W.; Sohnius, B.; Wehner, E.

    1990-01-01

    This paper present a procedure to calculate calibration factors for converting the measured gamma rate of waste drums into activity content and a layout and free release measurement criterion for waste drums. A computer program is developed that simulates drum scanning technique, which calculates calibration factors and eliminates laborious experimental measurements. The calculated calibration factors exhibit good agreement with experimentally determined values. By checking the calculated calibration factors for trial equipment layouts (including the waste drum and the scanning facility) using the layout and free release measurement criterion, a layout can be achieved that clearly determines whether there can be free release of a waste drum

  1. The performance of the ATLAS initial detector layout for B-physics channels

    International Nuclear Information System (INIS)

    Epp, B.; Ghete, V.M.; Kuhn, D.; Zhang, Y.J.

    2004-01-01

    At the start-up of LHC one expects parts of the ATLAS detector to be missing. This layout is called initial layout, whereas the fully staged detector is called complete layout. B-physics channels were simulated, reconstructed and analyzed using the software tools of ATLAS data challenge-1 (DC1). The performance of the detector with respect to quantities relevant to the analysis of the B s → D s π channel and the validation of the full chain generation-simulation-reconstruction-analysis were evaluated for the initial and complete layout. (author)

  2. Coplanar Electrode Layout Optimized for Increased Sensitivity for Electrical Impedance Spectroscopy

    DEFF Research Database (Denmark)

    Clausen, Casper Hyttel; Skands, Gustav Erik; Bertelsen, Christian Vinther

    2015-01-01

    This work describes an improvement in the layout of coplanar electrodes for electrical impedance spectroscopy. We have developed, fabricated, and tested an improved electrode layout, which improves the sensitivity of an impedance flow cytometry chip. The improved chip was experimentally tested...... and compared to a chip with a conventional electrode layout. The improved chip was able to discriminate 0.5 mu m beads from 1 mu m as opposed to the conventional chip. Furthermore, finite element modeling was used to simulate the improvements in electrical field density and uniformity between the electrodes...... of the new electrode layout. Good agreement was observed between the model and the obtained experimental results....

  3. Design and validation of dynamic hierarchies and adaptive layouts using spatial graph grammars

    NARCIS (Netherlands)

    Liao, K.; Kong, J.; Zhang, K.; de Vries, B.; Griffth, D.A.; Chun, Y.; Dean, D.J.

    2017-01-01

    With the thinking paradigm shifting on the evolution of complex adaptive systems, a pattern-based design approach is reviewed and reinterpreted. Although a variety of long-term and lasting explorations on patterns in geographical analysis, environmental planning, and design exist, in-depth

  4. Methodology for bus layout for topological quantum error correcting codes

    Energy Technology Data Exchange (ETDEWEB)

    Wosnitzka, Martin; Pedrocchi, Fabio L.; DiVincenzo, David P. [RWTH Aachen University, JARA Institute for Quantum Information, Aachen (Germany)

    2016-12-15

    Most quantum computing architectures can be realized as two-dimensional lattices of qubits that interact with each other. We take transmon qubits and transmission line resonators as promising candidates for qubits and couplers; we use them as basic building elements of a quantum code. We then propose a simple framework to determine the optimal experimental layout to realize quantum codes. We show that this engineering optimization problem can be reduced to the solution of standard binary linear programs. While solving such programs is a NP-hard problem, we propose a way to find scalable optimal architectures that require solving the linear program for a restricted number of qubits and couplers. We apply our methods to two celebrated quantum codes, namely the surface code and the Fibonacci code. (orig.)

  5. Mechanic- and hydraulic shock-absorbers - layout, construction, operation experience

    International Nuclear Information System (INIS)

    Kluge, M.

    1981-01-01

    The problem lies in the protection of the flexible supported power plant components against undesired sudden movements. Various shock absorbing systems are at disposal in this case: Mechanical and hydraulic shock absorbers, whose functioning systems are shown in figures. The operation experience showed a series of deficiencies, as demonstrated on various figures. In order to avoid them, some important recommendations are given. Requirements and layout are demonstrated according to todays' state-of-the-art. The admissible stresses, resulting from the summary of various specifications for the analytical evidence will be described. Development and construction will be explained in detail by means of pictures with cross sections of original shock absorbers. Todays' construction characteristics will be summarized. The final remark includes a request for generally valid guidelines. (orig.) [de

  6. Offshore Wind Farm Layout Design Considering Optimized Power Dispatch Strategy

    DEFF Research Database (Denmark)

    Hou, Peng; Hu, Weihao; N. Soltani, Mohsen

    2017-01-01

    Offshore wind farm has drawn more and more attention recently due to its higher energy capacity and more freedom to occupy area. However, the investment is higher. In order to make a cost-effective wind farm, the wind farm layout should be optimized. The wake effect is one of the dominant factors...... leading to energy losses. It is expected that the optimized placement of wind turbines (WT) over a large sea area can lead to the best tradeoff between energy yields and capital investment. This paper proposes a novel way to position offshore WTs for a regular shaped wind farm. In addition to optimizing...... the direction of wind farm placement and the spacing between WTs, the control strategy’s impact on energy yields is also discussed. Since the problem is non-convex and lots of optimization variables are involved, an evolutionary algorithm, the particle swarm optimization algorithm (PSO), is adopted to find...

  7. Forget about switching keyboard layouts with the "Compose Key"

    CERN Multimedia

    CERN. Geneva

    2018-01-01

    Growing up with a Spanish keyboard was not an easy childhood (using Shift+7 (/) to search in vim, or having to type AltGr+[ to actually have an opening bracket), so at some point in my life I switched to an American keyboard. At the beginning I was happy switching layouts to either do some coding or talk to my mum (I am not a fan of the classical excuse "sorry for my typos, I don't have the 'ñ' in my keyboard"). Things got much worse when I started to need French characters (ç, è) to interact with some services at CERN, or some Slovak letters (č, đ) to talk to Robert, my Slovak colleague . Then I discovered the Compose Key and my life has been different ever since.

  8. Overview of the Westinghouse Small Modular Reactor building layout

    Energy Technology Data Exchange (ETDEWEB)

    Cronje, J. M. [Westinghouse Electric Company LLC, Centurion (South Africa); Van Wyk, J. J.; Memmott, M. J. [Westinghouse Electric Company LLC, Cranberry Township, PA (United States)

    2012-07-01

    The Westinghouse Small Modular Reactor (SMR) is an 800 MWt (>225 MWe) integral pressurized water reactor (iPWR), in which all of the components typically associated with the nuclear steam supply system (NSSS) of a nuclear power plant are incorporated within a single reactor pressure vessel. This paper is the third in a series of four papers, which describe the design and functionality of the Westinghouse SMR. It focuses in particular upon the plant building layout and modular design of the Westinghouse SMR. In the development of small modular reactors, the building layout is an area where the safety of the plant can be improved by applying new design approaches. This paper will present an overview of the Westinghouse SMR building layout and indicate how the design features improve the safety and robustness of the plant. The Westinghouse SMR is designed with no shared systems between individual reactor units. The main buildings inside the security fence are the nuclear island, the rad-waste building, the annex building, and the turbine building. All safety related equipment is located in the nuclear island, which is a seismic class 1 building. To further enhance the safety and robustness of the design, the reactor, containment, and most of the safety related equipment are located below grade on the nuclear island. This reduces the possibility of severe damage from external threats or natural disasters. Two safety related ultimate heat sink (UHS) water tanks that are used for decay heat removal are located above grade, but are redundant and physically separated as far as possible for improved safety. The reactor and containment vessel are located below grade in the center of the nuclear island. The rad-waste and other radioactive systems are located on the bottom floors to limit the radiation exposure to personnel. The Westinghouse SMR safety trains are completely separated into four unconnected quadrants of the building, with access between quadrants only allowed

  9. An efficient grid layout algorithm for biological networks utilizing various biological attributes

    Directory of Open Access Journals (Sweden)

    Kato Mitsuru

    2007-03-01

    Full Text Available Abstract Background Clearly visualized biopathways provide a great help in understanding biological systems. However, manual drawing of large-scale biopathways is time consuming. We proposed a grid layout algorithm that can handle gene-regulatory networks and signal transduction pathways by considering edge-edge crossing, node-edge crossing, distance measure between nodes, and subcellular localization information from Gene Ontology. Consequently, the layout algorithm succeeded in drastically reducing these crossings in the apoptosis model. However, for larger-scale networks, we encountered three problems: (i the initial layout is often very far from any local optimum because nodes are initially placed at random, (ii from a biological viewpoint, human layouts still exceed automatic layouts in understanding because except subcellular localization, it does not fully utilize biological information of pathways, and (iii it employs a local search strategy in which the neighborhood is obtained by moving one node at each step, and automatic layouts suggest that simultaneous movements of multiple nodes are necessary for better layouts, while such extension may face worsening the time complexity. Results We propose a new grid layout algorithm. To address problem (i, we devised a new force-directed algorithm whose output is suitable as the initial layout. For (ii, we considered that an appropriate alignment of nodes having the same biological attribute is one of the most important factors of the comprehension, and we defined a new score function that gives an advantage to such configurations. For solving problem (iii, we developed a search strategy that considers swapping nodes as well as moving a node, while keeping the order of the time complexity. Though a naïve implementation increases by one order, the time complexity, we solved this difficulty by devising a method that caches differences between scores of a layout and its possible updates

  10. 33 CFR 127.105 - Layout and spacing of marine transfer area for LNG.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Layout and spacing of marine transfer area for LNG. 127.105 Section 127.105 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF... AND LIQUEFIED HAZARDOUS GAS Waterfront Facilities Handling Liquefied Natural Gas § 127.105 Layout and...

  11. Extracting 3D layout from a single image using global image structures.

    Science.gov (United States)

    Lou, Zhongyu; Gevers, Theo; Hu, Ninghang

    2015-10-01

    Extracting the pixel-level 3D layout from a single image is important for different applications, such as object localization, image, and video categorization. Traditionally, the 3D layout is derived by solving a pixel-level classification problem. However, the image-level 3D structure can be very beneficial for extracting pixel-level 3D layout since it implies the way how pixels in the image are organized. In this paper, we propose an approach that first predicts the global image structure, and then we use the global structure for fine-grained pixel-level 3D layout extraction. In particular, image features are extracted based on multiple layout templates. We then learn a discriminative model for classifying the global layout at the image-level. Using latent variables, we implicitly model the sublevel semantics of the image, which enrich the expressiveness of our model. After the image-level structure is obtained, it is used as the prior knowledge to infer pixel-wise 3D layout. Experiments show that the results of our model outperform the state-of-the-art methods by 11.7% for 3D structure classification. Moreover, we show that employing the 3D structure prior information yields accurate 3D scene layout segmentation.

  12. 49 CFR 238.447 - Train operator's controls and power car cab layout.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Train operator's controls and power car cab layout. 238.447 Section 238.447 Transportation Other Regulations Relating to Transportation (Continued... layout. (a) Train operator controls in the power car cab shall be arranged so as to minimize the chance...

  13. 33 CFR 127.1105 - Layout and spacing of marine transfer area for LHG.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Layout and spacing of marine transfer area for LHG. 127.1105 Section 127.1105 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF... Construction § 127.1105 Layout and spacing of marine transfer area for LHG. Each new waterfront facility...

  14. Design aspects of the alpha repository. II. Conceptual layouts of underground storage facilities

    International Nuclear Information System (INIS)

    Grams, W.H.

    1975-01-01

    Five conceptual repository layouts are presented: linear repository, 1 panel; bow tie repository, 2 panels; maltese cross repository, 4 panels; snowflake repository; 5 panels, and sash window repository, 8 panels. The layouts are compared with respect to excavation requirements, haulage distances, ventilation flow path designs, and safety features

  15. Yearbook and Magazine Layout, English, Journalism. Language Arts: 5113.200.

    Science.gov (United States)

    Adams, Marlene E.

    Developed as a quinmester unit for the high school on yearbook and magazine layout, this guide provides the teacher with suggested teaching strategies for a study of the theory and practice of page layout, photo cropping and editing, use of color and special effects, copy fitting and headline writing and fitting, and principles of typography.…

  16. A Tool for the Automated Design and Evaluation of Habitat Interior Layouts

    Science.gov (United States)

    Simon, Matthew A.; Wilhite, Alan W.

    2013-01-01

    The objective of space habitat design is to minimize mass and system size while providing adequate space for all necessary equipment and a functional layout that supports crew health and productivity. Unfortunately, development and evaluation of interior layouts is often ignored during conceptual design because of the subjectivity and long times required using current evaluation methods (e.g., human-in-the-loop mockup tests and in-depth CAD evaluations). Early, more objective assessment could prevent expensive design changes that may increase vehicle mass and compromise functionality. This paper describes a new interior design evaluation method to enable early, structured consideration of habitat interior layouts. This interior layout evaluation method features a comprehensive list of quantifiable habitat layout evaluation criteria, automatic methods to measure these criteria from a geometry model, and application of systems engineering tools and numerical methods to construct a multi-objective value function measuring the overall habitat layout performance. In addition to a detailed description of this method, a C++/OpenGL software tool which has been developed to implement this method is also discussed. This tool leverages geometry modeling coupled with collision detection techniques to identify favorable layouts subject to multiple constraints and objectives (e.g., minimize mass, maximize contiguous habitable volume, maximize task performance, and minimize crew safety risks). Finally, a few habitat layout evaluation examples are described to demonstrate the effectiveness of this method and tool to influence habitat design.

  17. Sensitivity Analysis of WEC Array Layout Parameters Effect on the Power Performance

    DEFF Research Database (Denmark)

    Ruiz, Pau Mercadé; Ferri, Francesco; Kofoed, Jens Peter

    2015-01-01

    This study assesses the effect that the array layout choice has on the power performance. To this end, a sensitivity analysis is carried out with six array layout parameters, as the simulation inputs, the array power performance (q-factor), as the simulation output, and a simulation model special...

  18. Layout level design for testability strategy applied to a CMOS cell library

    NARCIS (Netherlands)

    Blom, F.C.; Oliver, J.; Rullan, M.; Ferrer, C.

    1993-01-01

    The layout level design for testability (LLDFT) rules used here allow to avoid some hard to detect faults or even undetectable faults on a cell library by modifying the cell layout without changing their behavior and achieving a good level of reliability. These rules avoid some open faults or reduce

  19. Thermal Performance for Wet Cooling Tower with Different Layout Patterns of Fillings under Typical Crosswind Conditions

    Directory of Open Access Journals (Sweden)

    Ming Gao

    2017-01-01

    Full Text Available A thermal-state model experimental study was performed in lab to investigate the thermal performance of a wet cooling tower with different kinds of filling layout patterns under windless and 0.4 m/s crosswind conditions. In this paper, the contrast analysis was focused on comparing a uniform layout pattern and one kind of optimal non-uniform layout pattern when the environmental crosswind speed is 0 m/s and 0.4 m/s. The experimental results proved that under windless conditions, the heat transfer coefficient and total heat rejection of circulating water for the optimal non-uniform layout pattern can enhance by approximately 40% and 28%, respectively, compared with the uniform layout pattern. It was also discovered that the optimal non-uniform pattern can dramatically relieve the influence of crosswind on the thermal performance of the tower when the crosswind speed is equal to 0.4 m/s. For the uniform layout pattern, the heat transfer coefficient under 0.4 m/s crosswind conditions decreased by 9.5% compared with the windless conditions, while that value lowered only by 2.0% for the optimal non-uniform layout pattern. It has been demonstrated that the optimal non-uniform layout pattern has the better thermal performance under 0.4 m/s crosswind condition.

  20. Studies of Inner Detector Layouts with 5 Pixel layers for the Phase-II Upgrade

    CERN Document Server

    Ludwig, A; The ATLAS collaboration; Garcia-Sciveres, M

    2013-01-01

    This note describes a study of Inner Detector layouts for the phase-II upgrade. Starting from the LOI layout the impact of adding a 5th pixel layer, and shortening the pixel and/or SCT barrel layers is studied.

  1. An interactive system for the automatic layout of printed circuit boards (ARAIGNEE)

    International Nuclear Information System (INIS)

    Combet, M.; Eder, J.; Pagny, C.

    1974-12-01

    A software package for the automatic layout of printed circuit boards is presented. The program permits an interaction of the user during the layout process. The automatic searching of paths can be interrupted at any step and convenient corrections can be inserted. This procedure improves strongly the performance of the program as far as the number of unresolved connections is concerned

  2. Electrical Parasitics and Thermal Modeling for Optimized Layout Design of High Power SiC Modules

    DEFF Research Database (Denmark)

    Bahman, Amir Sajjad; Blaabjerg, Frede; Dutta, Atanu

    2016-01-01

    , the presented models are verified by a conventional and an optimized power module layout. The optimized layout is designed based on the reduction of stray inductance and temperature in a P-cell and N-cell half-bridge module. The presented models are verified by FEM simulations and also experiment....

  3. A Novel Energy Yields Calculation Method for Irregular Wind Farm Layout

    DEFF Research Database (Denmark)

    Hou, Peng; Hu, Weihao; Soltani, Mohsen

    2015-01-01

    Due to the increasing size of offshore wind farm, the impact of the wake effect on energy yields become more and more evident. The Seafloor topography would limit the layout of the wind farm so that irregular layout is usually adopted inlarge scale offshore wind farm. However, the calculation...

  4. The changing pages of comics : Page layouts across eight decades of American superhero comics

    NARCIS (Netherlands)

    Pederson, Kaitlin; Cohn, Neil

    2016-01-01

    Page layouts are one of the most overt features of comics’ structure. We hypothesized that American superhero comics have changed in their page layout over eight decades, and investigated this using a corpus analysis of 40 comics from 1940 through 2014. On the whole, we found that comics pages

  5. A novel approach of ensuring layout regularity correct by construction in advanced technologies

    Science.gov (United States)

    Ahmed, Shafquat Jahan; Vaderiya, Yagnesh; Gupta, Radhika; Parthasarathy, Chittoor; Marin, Jean-Claude; Robert, Frederic

    2017-03-01

    In advanced technology nodes, layout regularity has become a mandatory prerequisite to create robust designs less sensitive to variations in manufacturing process in order to improve yield and minimizing electrical variability. In this paper we describe a method for designing regular full custom layouts based on design and process co-optimization. The method includes various design rule checks that can be used on-the-fly during leaf-cell layout development. We extract a Layout Regularity Index (LRI) from the layouts based on the jogs, alignments and pitches used in the design for any given metal layer. Regularity Index of a layout is the direct indicator of manufacturing yield and is used to compare the relative health of different layout blocks in terms of process friendliness. The method has been deployed for 28nm and 40nm technology nodes for Memory IP and is being extended to other IPs (IO, standard-cell). We have quantified the gain of layout regularity with the deployed method on printability and electrical characteristics by process-variation (PV) band simulation analysis and have achieved up-to 5nm reduction in PV band.

  6. Young children reorient by computing layout geometry, not by matching images of the environment.

    Science.gov (United States)

    Lee, Sang Ah; Spelke, Elizabeth S

    2011-02-01

    Disoriented animals from ants to humans reorient in accord with the shape of the surrounding surface layout: a behavioral pattern long taken as evidence for sensitivity to layout geometry. Recent computational models suggest, however, that the reorientation process may not depend on geometrical analyses but instead on the matching of brightness contours in 2D images of the environment. Here we test this suggestion by investigating young children's reorientation in enclosed environments. Children reoriented by extremely subtle geometric properties of the 3D layout: bumps and ridges that protruded only slightly off the floor, producing edges with low contrast. Moreover, children failed to reorient by prominent brightness contours in continuous layouts with no distinctive 3D structure. The findings provide evidence that geometric layout representations support children's reorientation.

  7. Economy analysis on vertical layout of conventional island of nuclear power plant

    International Nuclear Information System (INIS)

    Wang Xuefeng; Liu Xiaoyun; Liu Jinwei

    2011-01-01

    This paper briefly introduces the aboveground layout scheme and integral sinking layout scheme of conventional island of nuclear power plants. Technological-economic analysis formula are given, as a result, main factors influencing scheme selection is obtained. Determination of the layout scheme selection and optimization direction through the curve between the accumulative NPV and related factors is brought forward. The paper carries out the technological-economic comparison to the two schemes referred to a 1000 MW level nuclear power project as the example, getting the curve between the accumulative NPV and the plant ground elevation, and offering the method of selecting the vertical layout scheme of conventional island and vertical layout optimization direction. (authors)

  8. Using the clustered circular layout as an informative method for visualizing protein-protein interaction networks.

    Science.gov (United States)

    Fung, David C Y; Wilkins, Marc R; Hart, David; Hong, Seok-Hee

    2010-07-01

    The force-directed layout is commonly used in computer-generated visualizations of protein-protein interaction networks. While it is good for providing a visual outline of the protein complexes and their interactions, it has two limitations when used as a visual analysis method. The first is poor reproducibility. Repeated running of the algorithm does not necessarily generate the same layout, therefore, demanding cognitive readaptation on the investigator's part. The second limitation is that it does not explicitly display complementary biological information, e.g. Gene Ontology, other than the protein names or gene symbols. Here, we present an alternative layout called the clustered circular layout. Using the human DNA replication protein-protein interaction network as a case study, we compared the two network layouts for their merits and limitations in supporting visual analysis.

  9. Apron layout design and flight-to-gate assignment at Lanseria International airport

    Directory of Open Access Journals (Sweden)

    Leonard, T.

    2013-05-01

    Full Text Available Air traffic is continuously increasing and more efficient air transport systems are required to handle the air travel demand. The study investigates the expansion of Lanseria International Airport in Gauteng, South Africa. Expansion of Lanseria requires a study of the airport apron layout to ensure efficient passenger-aircraft flow as well as the efficient flow of aircraft to and from the airport. The candidate layout designs are based on the layout concept of the Hartsfield-Jackson Atlanta International Airport in Atlanta, USA. In the study, different airport apron layouts were compared, including the existing layout of Atlanta Airport, via a simulation model of each. Designs based mainly on passenger transfer distance between the terminal building and aircraft were evaluated. The cross-entropy method was used to develop a generic flight-to-gate assignment program that minimises passenger transfer distances.

  10. A descriptive analysis of quantitative indices for multi-objective block layout

    Directory of Open Access Journals (Sweden)

    Amalia Medina Palomera

    2013-01-01

    Full Text Available Layout generation methods provide alternative solutions whose feasibility and quality must be evaluated. Indices must be used to distinguish the feasible solutions (involving different criteria obtained for block layout to identify s solution’s suitability, according to set objectives. This paper provides an accurate and descriptive analysis of the geometric indices used in designing facility layout (during block layout phase. The indices studied here have advantages and disadvantages which should be considered by an analyst before attempting to resolve the facility layout problem. New equations are proposed for measuring geometric indices. The analysis revealed redundant indices and that a minimum number of indices covering overall quality criteria may be used when selecting alternative solutions.

  11. Constructing an optimal facility layout to maximize adjacency as a function of common boundary length

    Science.gov (United States)

    Ghassemi Tari, Farhad; Neghabi, Hossein

    2018-03-01

    An effective facility layout implies that departments with high flow are laid adjacent. However, in the case of a very narrow boundary length between the neighbouring departments, the adjacency would actually be useless. In traditional layout design methods, a score is generally assigned independent of the department's boundary length. This may result in a layout design with a restricted material flow. This article proposes a new concept of adjacency in which the department pairs are laid adjacent with a wider path. To apply this concept, a shop with unequal rectangular departments is contemplated and a mathematical programming model with the objective of maximizing the sum of the adjacency degrees is proposed. A computational experiment is conducted to demonstrate the efficiency of the layout design. It is demonstrated that the new concept provides a more efficient and a more realistic layout design.

  12. Spatial-frequency Fourier polarimetry of the complex degree of mutual anisotropy of linear and circular birefringence in the diagnostics of oncological changes in morphological structure of biological tissues

    International Nuclear Information System (INIS)

    Ushenko, Yu A; Gorskii, M P; Dubolazov, A V; Motrich, A V; Ushenko, V A; Sidor, M I

    2012-01-01

    Theory of polarisation-correlation analysis of laser images of histological sections of biopsy material from cervix tissue based on spatial frequency selection of linear and circular birefringence mechanisms is formulated. Comparative results of measuring the coordinate distributions of the complex degree of mutual anisotropy (CDMA), produced by fibrillar networks formed by myosin and collagen fibres of cervix tissue in different pathological conditions, namely, pre-cancer (dysplasia) and cancer (adenocarcinoma), are presented. The values and variation ranges of statistical (moments of the first — fourth order), correlation (excess-autocorrelation functions), and fractal (slopes of approximating curves and dispersion of extrema of logarithmic dependences of power spectra) parameters of the CDMA coordinate distributions are studied. Objective criteria for pathology diagnostics and differentiation of its severity degree are determined. (image processing)

  13. A Study of Layout, Rendering, and Interaction Methods for Immersive Graph Visualization.

    Science.gov (United States)

    Kwon, Oh-Hyun; Muelder, Chris; Lee, Kyungwon; Ma, Kwan-Liu

    2016-07-01

    Information visualization has traditionally limited itself to 2D representations, primarily due to the prevalence of 2D displays and report formats. However, there has been a recent surge in popularity of consumer grade 3D displays and immersive head-mounted displays (HMDs). The ubiquity of such displays enables the possibility of immersive, stereoscopic visualization environments. While techniques that utilize such immersive environments have been explored extensively for spatial and scientific visualizations, contrastingly very little has been explored for information visualization. In this paper, we present our considerations of layout, rendering, and interaction methods for visualizing graphs in an immersive environment. We conducted a user study to evaluate our techniques compared to traditional 2D graph visualization. The results show that participants answered significantly faster with a fewer number of interactions using our techniques, especially for more difficult tasks. While the overall correctness rates are not significantly different, we found that participants gave significantly more correct answers using our techniques for larger graphs.

  14. Creating a Single South African Keyboard Layout to Promote Language

    Directory of Open Access Journals (Sweden)

    Dwayne Bailey

    2011-10-01

    Full Text Available

    Abstract: In this case study, a description is given of a keyboard layout designed to address the input needs of South African languages, specifically Venda, a language which would otherwise be impossible to type on a computer. In creating this keyboard, the designer, Translate.org.za, uses a practical intervention that transforms technology from a means harming a language into one ensuring the creation and preservation of good language resources for minority languages. The study first looks at the implications and consequences of this missing keyboard, and then follows the process from conception, strategy, research and design to the final user response. Not only are problems such as researching the orthographies, key placement and keyboard input options examined, but strategic objectives such as ensuring its wide adoption and creating a multilingual keyboard for all South African languages are also discussed. The result is a keyboard that furthers multilingualism and ensures the capturing of good data for future research. Finally it is a tool helping to boost and bolster the vitality of a language.

    Keywords: KEYBOARD, MULTILINGUALISM, VENDA, AFRIKAANS, TSWANA, NORTH-ERN SOTHO, ZULU, SOURCE, FREE SOFTWARE, LAYOUT

    Opsomming: Die skep van 'n enkelvoudige Suid-Afrikaanse toetsborduit-leg om taal te bevorder. In hierdie gevallestudie word 'n beskrywing gegee van die ontwerp van 'n sleutelborduitleg vir die hantering van die insetbehoeftes van Suid-Afrikaanse tale, veral Venda, 'n taal wat andersins onmoontlik op 'n rekenaar getik sou kon word. Deur die skep van hierdie sleutelbord gebruik die ontwerper, Translate.org.za, 'n praktiese ingryp wat tegnologie verander van 'n middel wat 'n taal benadeel tot een wat die skep en bewaring van nuttige taal-hulpbronne vir minderheidstale verseker. Die studie kyk eers na die implikasies en gevolge van hierdie ontbrekende sleutelbord, en volg dan die proses van konsepsie, strategie, navorsing en

  15. Progress report on research project [Plan for www interface layout

    International Nuclear Information System (INIS)

    Fukahori, T.

    2006-01-01

    Full text: Presentations and status reports. T. Fukahori reported the plan for www interface layout as a status report. Discussed were which functions were needed for new RIPL-3 web pages. The results are summarized in next section. Layout of the interfaces and retrieval tools and web. The RIPL-3 home page will include a summary description and link to the HANDBOOK: a) The web page for 'mass' segment contains same contents as RIPL-2 except to remove the information about ground state deformation. The abundance data will be replaced by those according to the new BNL wallet card (2005 version). The Q-value calculation tool will be also improved. The 'Nuclear Matter Density' will be renamed as 'Nucleon Density Distribution'. b) Those of 'levels' segment will be same as before, and the deformation parameters for excited levels will be moved from 'optical' segment with the name of 'deformation'. c) Those of 'resonances' segment will be same as before. It will be considered to replace RIPL-2 database with the new Mughabghab tables. d) Those of 'optical' segment will be same as before, and the deformation parameters for excited levels will be moved to 'optical' segment with the name of 'deformation'. The optical model calculation with ECIS and OPTMAN will be considered and double-folding calculation tool will be possibly provided. e) Those of 'densities' segment will be same as before, and the programs used to plot will be checked. The 3-7 sets of combination of GC, BSFG, GSFM with/without enhancement factors will be given. f) Those of 'gamma' segment will be same as before with adding MLO and theoretical GDR calculation. g) Those of 'fission' segment will be same as before, and 'Exp.' will be renamed. New barrier evaluations will be added. Some additional information could be included, for example, fission transition states. The fission spectrum calculation tool (codes and inputs) will be considered to be added. The fundamental format will be kept as before. For new

  16. Bimodal spectroscopy in elastic scattering and spatially resolved auto-fluorescence: instrumentation, light-tissues interaction modeling and application to ex vivo and in vivo biological tissues characterization for cancers detection

    International Nuclear Information System (INIS)

    Pery, Emilie

    2007-01-01

    This research activity aims at developing and validating a multimodal spectroscopy method in elastic scattering and auto-fluorescence to characterize biological tissues in vitro and in vivo. It is articulated in four axes. At first, instrumentation is considered with the development, the engineering and the experimental characterization of a fibers bimodal, multi-points spectrometry system allowing the acquisition of spectra in vivo (variable distances, fast acquisition). Secondly, the optical properties of tissues are modelled with the development and the experimental validation on phantoms of a photons propagation simulation algorithm in turbid media and multi-fluorescent. Thirdly, an experimental study has been conducted ex vivo on fresh and cryo-preserved arterial rings. It confirms the complementarity of spectroscopic measurements in elastic scattering and auto-fluorescence, and validates the method of multi-modality spectroscopy and the simulation of photons propagation algorithm. Results have well proved a correlation between rheological and optical properties. Finally, one second experimental study in vivo related to a pre-clinical tumoral model of bladder has been carried out. It highlights a significant difference in diffuse reflectance and/or auto-fluorescence and/or intrinsic fluorescence between healthy, inflammatory and tumoral tissues, on the basis of specific wavelength. The results of not supervised classification show that the combination of various spectroscopic approaches increases the reliability of the diagnosis. (author) [fr

  17. Relation between front suspension layout and handling performance. Analysis depending on the Taguchi method and ADAMS; Front suspension layout to soda tokusei no kankei ni tsuite. Kiko kaiseki gengo wo mochiita hinshitsu kogaku ni yoru kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Okada, K [Daihatsu Motor Co. Ltd., Osaka (Japan)

    1997-10-01

    A variation of suspension layout gives an influence to the vehicle dynamics. Examined the suspension layout variation to make the handling performance change small. Analyzed the effect of suspension layout variation about steering response delay and gain besides the tire wear effect and movable load. 3 refs., 12 figs., 4 tabs.

  18. Environmental layout complexity affects neural activity during navigation in humans.

    Science.gov (United States)

    Slone, Edward; Burles, Ford; Iaria, Giuseppe

    2016-05-01

    Navigating large-scale surroundings is a fundamental ability. In humans, it is commonly assumed that navigational performance is affected by individual differences, such as age, sex, and cognitive strategies adopted for orientation. We recently showed that the layout of the environment itself also influences how well people are able to find their way within it, yet it remains unclear whether differences in environmental complexity are associated with changes in brain activity during navigation. We used functional magnetic resonance imaging to investigate how the brain responds to a change in environmental complexity by asking participants to perform a navigation task in two large-scale virtual environments that differed solely in interconnection density, a measure of complexity defined as the average number of directional choices at decision points. The results showed that navigation in the simpler, less interconnected environment was faster and more accurate relative to the complex environment, and such performance was associated with increased activity in a number of brain areas (i.e. precuneus, retrosplenial cortex, and hippocampus) known to be involved in mental imagery, navigation, and memory. These findings provide novel evidence that environmental complexity not only affects navigational behaviour, but also modulates activity in brain regions that are important for successful orientation and navigation. © 2016 Federation of European Neuroscience Societies and John Wiley & Sons Ltd.

  19. Experimental verification of layout physical verification of silicon photonics

    Science.gov (United States)

    El Shamy, Raghi S.; Swillam, Mohamed A.

    2018-02-01

    Silicon photonics have been approved as one of the best platforms for dense integration of photonic integrated circuits (PICs) due to the high refractive index contrast among its materials. Silicon on insulator (SOI) is a widespread photonics technology, which support a variety of devices for lots of applications. As the photonics market is growing, the number of components in the PICs increases which increase the need for an automated physical verification (PV) process. This PV process will assure reliable fabrication of the PICs as it will check both the manufacturability and the reliability of the circuit. However, PV process is challenging in the case of PICs as it requires running an exhaustive electromagnetic (EM) simulations. Our group have recently proposed an empirical closed form models for the directional coupler and the waveguide bends based on the SOI technology. The models have shown a very good agreement with both finite element method (FEM) and finite difference time domain (FDTD) solvers. These models save the huge time of the 3D EM simulations and can be easily included in any electronic design automation (EDA) flow as the equations parameters can be easily extracted from the layout. In this paper we present experimental verification for our previously proposed models. SOI directional couplers with different dimensions have been fabricated using electron beam lithography and measured. The results from the measurements of the fabricate devices have been compared to the derived models and show a very good agreement. Also the matching can reach 100% by calibrating certain parameter in the model.

  20. International Thermonuclear Experimental Reactor (ITER) plant layout and site services

    International Nuclear Information System (INIS)

    Chuyanov, V.

    2001-01-01

    The ITER site has not been determined at this time. Nevertheless, to develop a construction plan and a cost estimate, it is necessary to have a detailed layout of the buildings, structures, and outdoor equipment integrated with the balance of plant service systems prototypical of large fusion power plants. These services include electric power for magnet feeds and plasma heating systems, cryogenic and conventional cooling systems, compressed air, gas supplies, de-mineralized water, steam, and drainage. Nuclear grade facilities are provided to handle tritium fuel and activated waste, as well as to prevent radioactive exposure of either the workers or the public. To avoid interference between services of different types and for efficient arrangement of buildings, structures, and equipment within the site area, a plan was developed which segregated different classes of services to four quadrants surrounding the tokamak building, placed at the approximate geographic center of the site. Location of the twenty-seven buildings on the generic site was selected to meet all design requirements at minimum total project cost. A similar approach has been used to determine the location of services above, at, and below grade. The generic site plan can be adapted to the site selected for ITER without significant changes to the buildings or equipment. Some rearrangements may be required by site topography resulting primarily in changes to the length of services that link the buildings and equipment. (author)

  1. LAYOUT AND DESIGN OF ELECTROMOBILE CHARGING STATIONS AS URBAN ELEMENTS

    Directory of Open Access Journals (Sweden)

    Tomáš Chovan

    2015-12-01

    Full Text Available The contribution is dedicated to the processing of the problems of the insufficient charging for the electric vehicles within the concrete urbanistic centre. It brings a different perspective on the mobility, which is shown in the form of electric energy as the alternative for the needs of urbanization of the cities. It analyses electromobility, new technologies in the field of electric vehicles and the charging stations as the elements of the urbanism. In terms of the solution, the contribution is focused on the Košice city and the location of the public charging stations. Košice do not have sufficient amount of the public charging stations and until the 2014 there was only one public charging station. The contribution is focused on the designing of the parking places with the charging station placed on the appropriate parking places. The resulting design is created in the CAD system, it brings the view of the layout of the charging station at the shopping centre in the open space and in the parking house.

  2. Inherent safety features in balance-of-plant layout

    International Nuclear Information System (INIS)

    Wattelet, P.L.; Green, K.J.

    1992-01-01

    Future nuclear units must be more economical to construct and operate, and, at the same time, clearly incorporate advances in safety over the current generation of light water reactors. To achieve these goals, the root causes of safety issues must be addressed. In this way, global, cost-effective solutions can be implemented. With simple, direct design approaches, the licensing risk is minimized and configuration control is enhanced. With proper planning in the early stages of plant design, postulated accidents and events can often be mitigated by passive features inherent in the basic structure and layout, eliminating expensive added protective structures and components often found in current designs. Korea Electric Power Corporation's Yonggwang (YGN) Units 3 and 4, shown in an artist's rendering in Figure 1, are now under construction in Korea. Engineering is more than 85% complete, and Unit 3 construction is more than 50% complete. Significant steps toward design simplification and safety enhancement have been made by addressing safety concerns very early in the design effort. The tools used to achieve this were improved symmetry and separation, isolation of potential hazards, and an improved design process

  3. Optimization of wind farm turbines layout using an evolutive algorithm

    International Nuclear Information System (INIS)

    Gonzalez, Javier Serrano; Santos, Jesus Riquelme; Payan, Manuel Burgos; Gonzalez Rodriguez, Angel G.; Mora, Jose Castro

    2010-01-01

    The optimum wind farm configuration problem is discussed in this paper and an evolutive algorithm to optimize the wind farm layout is proposed. The algorithm's optimization process is based on a global wind farm cost model using the initial investment and the present value of the yearly net cash flow during the entire wind-farm life span. The proposed algorithm calculates the yearly income due to the sale of the net generated energy taking into account the individual wind turbine loss of production due to wake decay effects and it can deal with areas or terrains with non-uniform load-bearing capacity soil and different roughness length for every wind direction or restrictions such as forbidden areas or limitations in the number of wind turbines or the investment. The results are first favorably compared with those previously published and a second collection of test cases is used to proof the performance and suitability of the proposed evolutive algorithm to find the optimum wind farm configuration. (author)

  4. LADS: Optimizing Data Transfers using Layout-Aware Data Scheduling

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Youngjae [ORNL; Atchley, Scott [ORNL; Vallee, Geoffroy R [ORNL; Shipman, Galen M [ORNL

    2015-01-01

    While future terabit networks hold the promise of signifi- cantly improving big-data motion among geographically distributed data centers, significant challenges must be overcome even on today s 100 gigabit networks to real- ize end-to-end performance. Multiple bottlenecks exist along the end-to-end path from source to sink. Data stor- age infrastructure at both the source and sink and its in- terplay with the wide-area network are increasingly the bottleneck to achieving high performance. In this paper, we identify the issues that lead to congestion on the path of an end-to-end data transfer in the terabit network en- vironment, and we present a new bulk data movement framework called LADS for terabit networks. LADS ex- ploits the underlying storage layout at each endpoint to maximize throughput without negatively impacting the performance of shared storage resources for other users. LADS also uses the Common Communication Interface (CCI) in lieu of the sockets interface to use zero-copy, OS-bypass hardware when available. It can further im- prove data transfer performance under congestion on the end systems using buffering at the source using flash storage. With our evaluations, we show that LADS can avoid congested storage elements within the shared stor- age resource, improving I/O bandwidth, and data transfer rates across the high speed networks.

  5. Automatic pattern localization across layout database and photolithography mask

    Science.gov (United States)

    Morey, Philippe; Brault, Frederic; Beisser, Eric; Ache, Oliver; Röth, Klaus-Dieter

    2016-03-01

    Advanced process photolithography masks require more and more controls for registration versus design and critical dimension uniformity (CDU). The distribution of the measurement points should be distributed all over the whole mask and may be denser in areas critical to wafer overlay requirements. This means that some, if not many, of theses controls should be made inside the customer die and may use non-dedicated patterns. It is then mandatory to access the original layout database to select patterns for the metrology process. Finding hundreds of relevant patterns in a database containing billions of polygons may be possible, but in addition, it is mandatory to create the complete metrology job fast and reliable. Combining, on one hand, a software expertise in mask databases processing and, on the other hand, advanced skills in control and registration equipment, we have developed a Mask Dataprep Station able to select an appropriate number of measurement targets and their positions in a huge database and automatically create measurement jobs on the corresponding area on the mask for the registration metrology system. In addition, the required design clips are generated from the database in order to perform the rendering procedure on the metrology system. This new methodology has been validated on real production line for the most advanced process. This paper presents the main challenges that we have faced, as well as some results on the global performances.

  6. Sandia Agile MEMS Prototyping, Layout Tools, Education and Services Program

    Energy Technology Data Exchange (ETDEWEB)

    Schriner, H.; Davies, B.; Sniegowski, J.; Rodgers, M.S.; Allen, J.; Shepard, C.

    1998-05-01

    Research and development in the design and manufacture of Microelectromechanical Systems (MEMS) is growing at an enormous rate. Advances in MEMS design tools and fabrication processes at Sandia National Laboratories` Microelectronics Development Laboratory (MDL) have broadened the scope of MEMS applications that can be designed and manufactured for both military and commercial use. As improvements in micromachining fabrication technologies continue to be made, MEMS designs can become more complex, thus opening the door to an even broader set of MEMS applications. In an effort to further research and development in MEMS design, fabrication, and application, Sandia National Laboratories has launched the Sandia Agile MEMS Prototyping, Layout Tools, Education and Services Program or SAMPLES program. The SAMPLES program offers potential partners interested in MEMS the opportunity to prototype an idea and produce hardware that can be used to sell a concept. The SAMPLES program provides education and training on Sandia`s design tools, analysis tools and fabrication process. New designers can participate in the SAMPLES program and design MEMS devices using Sandia`s design and analysis tools. As part of the SAMPLES program, participants` designs are fabricated using Sandia`s 4 level polycrystalline silicon surface micromachine technology fabrication process known as SUMMiT (Sandia Ultra-planar, Multi-level MEMS Technology). Furthermore, SAMPLES participants can also opt to obtain state of the art, post-fabrication services provided at Sandia such as release, packaging, reliability characterization, and failure analysis. This paper discusses the components of the SAMPLES program.

  7. International Thermonuclear Experimental Reactor (ITER) plant layout and site services

    International Nuclear Information System (INIS)

    Chuyanov, V.

    1999-01-01

    The ITER site has not been determined at this time. Nevertheless, to develop a construction plan and a cost estimate, it is necessary to have a detailed layout of the buildings, structures, and outdoor equipment integrated with the balance of plant service systems prototypical of large fusion power plants. These services include electric power for magnet feeds and plasma heating systems, cryogenic and conventional cooling systems, compressed air, gas supplies, de-mineralized water, steam, and drainage. Nuclear grade facilities are provided to handle tritium fuel and activated waste, as well as to prevent radioactive exposure of either the workers or the public. To avoid interference between services of different types and for efficient arrangement of buildings, structures, and equipment within the site area, a plan was developed which segregated different classes of services to four quadrants surrounding the tokamak building, placed at the approximate geographic center of the site. Location of the twenty-seven buildings on the generic site was selected to meet all design requirements at minimum total project cost. A similar approach has been used to determine the location of services above, at, and below grade. The generic site plan can be adapted to the site selected for ITER without significant changes to the buildings or equipment. Some rearrangements may be required by site topography resulting primarily in changes to the length of services that link the buildings and equipment. (author)

  8. Safety assessment in plant layout design using indexing approach: Implementing inherent safety perspective

    International Nuclear Information System (INIS)

    Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

    2008-01-01

    Layout planning plays a key role in the inherent safety performance of process plants since this design feature controls the possibility of accidental chain-events and the magnitude of possible consequences. A lack of suitable methods to promote the effective implementation of inherent safety in layout design calls for the development of new techniques and methods. In the present paper, a safety assessment approach suitable for layout design in the critical early phase is proposed. The concept of inherent safety is implemented within this safety assessment; the approach is based on an integrated assessment of inherent safety guideword applicability within the constraints typically present in layout design. Application of these guidewords is evaluated along with unit hazards and control devices to quantitatively map the safety performance of different layout options. Moreover, the economic aspects related to safety and inherent safety are evaluated by the method. Specific sub-indices are developed within the integrated safety assessment system to analyze and quantify the hazard related to domino effects. The proposed approach is quick in application, auditable and shares a common framework applicable in other phases of the design lifecycle (e.g. process design). The present work is divided in two parts: Part 1 (current paper) presents the application of inherent safety guidelines in layout design and the index method for safety assessment; Part 2 (accompanying paper) describes the domino hazard sub-index and demonstrates the proposed approach with a case study, thus evidencing the introduction of inherent safety features in layout design

  9. Application of approximate pattern matching in two dimensional spaces to grid layout for biochemical network maps.

    Science.gov (United States)

    Inoue, Kentaro; Shimozono, Shinichi; Yoshida, Hideaki; Kurata, Hiroyuki

    2012-01-01

    For visualizing large-scale biochemical network maps, it is important to calculate the coordinates of molecular nodes quickly and to enhance the understanding or traceability of them. The grid layout is effective in drawing compact, orderly, balanced network maps with node label spaces, but existing grid layout algorithms often require a high computational cost because they have to consider complicated positional constraints through the entire optimization process. We propose a hybrid grid layout algorithm that consists of a non-grid, fast layout (preprocessor) algorithm and an approximate pattern matching algorithm that distributes the resultant preprocessed nodes on square grid points. To demonstrate the feasibility of the hybrid layout algorithm, it is characterized in terms of the calculation time, numbers of edge-edge and node-edge crossings, relative edge lengths, and F-measures. The proposed algorithm achieves outstanding performances compared with other existing grid layouts. Use of an approximate pattern matching algorithm quickly redistributes the laid-out nodes by fast, non-grid algorithms on the square grid points, while preserving the topological relationships among the nodes. The proposed algorithm is a novel use of the pattern matching, thereby providing a breakthrough for grid layout. This application program can be freely downloaded from http://www.cadlive.jp/hybridlayout/hybridlayout.html.

  10. Application of approximate pattern matching in two dimensional spaces to grid layout for biochemical network maps.

    Directory of Open Access Journals (Sweden)

    Kentaro Inoue

    Full Text Available BACKGROUND: For visualizing large-scale biochemical network maps, it is important to calculate the coordinates of molecular nodes quickly and to enhance the understanding or traceability of them. The grid layout is effective in drawing compact, orderly, balanced network maps with node label spaces, but existing grid layout algorithms often require a high computational cost because they have to consider complicated positional constraints through the entire optimization process. RESULTS: We propose a hybrid grid layout algorithm that consists of a non-grid, fast layout (preprocessor algorithm and an approximate pattern matching algorithm that distributes the resultant preprocessed nodes on square grid points. To demonstrate the feasibility of the hybrid layout algorithm, it is characterized in terms of the calculation time, numbers of edge-edge and node-edge crossings, relative edge lengths, and F-measures. The proposed algorithm achieves outstanding performances compared with other existing grid layouts. CONCLUSIONS: Use of an approximate pattern matching algorithm quickly redistributes the laid-out nodes by fast, non-grid algorithms on the square grid points, while preserving the topological relationships among the nodes. The proposed algorithm is a novel use of the pattern matching, thereby providing a breakthrough for grid layout. This application program can be freely downloaded from http://www.cadlive.jp/hybridlayout/hybridlayout.html.

  11. Safety assessment in plant layout design using indexing approach: Implementing inherent safety perspective

    International Nuclear Information System (INIS)

    Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

    2008-01-01

    The design of layout plans requires adequate assessment tools for the quantification of safety performance. The general focus of the present work is to introduce an inherent safety perspective at different points of the layout design process. In particular, index approaches for safety assessment and decision-making in the early stages of layout design are developed and discussed in this two-part contribution. Part 1 (accompanying paper) of the current work presents an integrated index approach for safety assessment of early plant layout. In the present paper (Part 2), an index for evaluation of the hazard related to the potential of domino effects is developed. The index considers the actual consequences of possible escalation scenarios and scores or ranks the subsequent accident propagation potential. The effects of inherent and passive protection measures are also assessed. The result is a rapid quantification of domino hazard potential that can provide substantial support for choices in the early stages of layout design. Additionally, a case study concerning selection among various layout options is presented and analyzed. The case study demonstrates the use and applicability of the indices developed in both parts of the current work and highlights the value of introducing inherent safety features early in layout design

  12. Automated Spatial Brain Normalization and Hindbrain White Matter Reference Tissue Give Improved [(18)F]-Florbetaben PET Quantitation in Alzheimer's Model Mice.

    Science.gov (United States)

    Overhoff, Felix; Brendel, Matthias; Jaworska, Anna; Korzhova, Viktoria; Delker, Andreas; Probst, Federico; Focke, Carola; Gildehaus, Franz-Josef; Carlsen, Janette; Baumann, Karlheinz; Haass, Christian; Bartenstein, Peter; Herms, Jochen; Rominger, Axel

    2016-01-01

    Preclinical PET studies of β-amyloid (Aβ) accumulation are of growing importance, but comparisons between research sites require standardized and optimized methods for quantitation. Therefore, we aimed to evaluate systematically the (1) impact of an automated algorithm for spatial brain normalization, and (2) intensity scaling methods of different reference regions for Aβ-PET in a large dataset of transgenic mice. PS2APP mice in a 6 week longitudinal setting (N = 37) and another set of PS2APP mice at a histologically assessed narrow range of Aβ burden (N = 40) were investigated by [(18)F]-florbetaben PET. Manual spatial normalization by three readers at different training levels was performed prior to application of an automated brain spatial normalization and inter-reader agreement was assessed by Fleiss Kappa (κ). For this method the impact of templates at different pathology stages was investigated. Four different reference regions on brain uptake normalization were used to calculate frontal cortical standardized uptake value ratios (SUVRCTX∕REF), relative to raw SUVCTX. Results were compared on the basis of longitudinal stability (Cohen's d), and in reference to gold standard histopathological quantitation (Pearson's R). Application of an automated brain spatial normalization resulted in nearly perfect agreement (all κ≥0.99) between different readers, with constant or improved correlation with histology. Templates based on inappropriate pathology stage resulted in up to 2.9% systematic bias for SUVRCTX∕REF. All SUVRCTX∕REF methods performed better than SUVCTX both with regard to longitudinal stability (d≥1.21 vs. d = 0.23) and histological gold standard agreement (R≥0.66 vs. R≥0.31). Voxel-wise analysis suggested a physiologically implausible longitudinal decrease by global mean scaling. The hindbrain white matter reference (R mean = 0.75) was slightly superior to the brainstem (R mean = 0.74) and the cerebellum (R mean = 0.73). Automated

  13. The stress analysis evaluation and pipe support layout for pressurizer discharge system

    International Nuclear Information System (INIS)

    Mao Qing; Wang Wei; Zhang Yixiong

    2000-01-01

    The author presents the stress analysis and evaluation of pipe layout and support adjustment process for Qinshan phase II pressurizer discharge system. Using PDL-SYSPIPE INTERFACE software, the characteristic parameters of the system are gained from 3-D CAD engineering design software PDL and outputted as the input date file format of special pipe stress analysis program SYSPIPE. Based on that, SYSPIPE program fast stress analysis function is applied in adjusting pipe layout , support layout and support types. According to RCC-M standard, the pipe stress analysis and evaluation under deadweight, internal pressure, thermal expansion, seismic, pipe rupture and discharge loads are fulfilled

  14. Mathematical programming models for solving in equal-sized facilities layout problems. A genetic search method

    International Nuclear Information System (INIS)

    Tavakkoli-Moghaddam, R.

    1999-01-01

    This paper present unequal-sized facilities layout solutions generated by a genetic search program. named Layout Design using a Genetic Algorithm) 9. The generalized quadratic assignment problem requiring pre-determined distance and material flow matrices as the input data and the continuous plane model employing a dynamic distance measure and a material flow matrix are discussed. Computational results on test problems are reported as compared with layout solutions generated by the branch - and bound algorithm a hybrid method merging simulated annealing and local search techniques, and an optimization process of an enveloped block

  15. B-physics performance with Initial and Complete Inner detector layouts in Data Challenge-1

    CERN Document Server

    Benekos, N C; Bouhova-Thacker, E; Epp, B; Ghete, V M; Jones, R; Kartvelishvili, V G; Lagouri, T; Laporte, J F; Nairz, A; Nikitine, N; Reznicek, P; Sivoklokov, S Yu; Smizanska, M; Testa, M; Toms, K

    2004-01-01

    The B-physics performance for the Initial and the Complete Inner Detector layouts is presented. Selected types of B-physics events were simulated, reconstructed and analyzed using the software tools of ATLAS Data Challenge-1 (DC1). The results were compared to those obtained with an older ATLAS detector design the so-called TDR layout. Within the limitations of the DC1 software tools an attempt was made to evaluate the performance loss due to missing detector parts in the Initial layout in comparison with the Complete detector.

  16. dRail: a novel physical layout methodology for power gated circuits

    OpenAIRE

    Mistry, Jatin N.; Biggs, John; Myers, James; Al-Hashimi, Bashir M.; Flynn, David

    2012-01-01

    In this paper we present a physical layout methodology, called dRail, to allow power gated and non-power gated cells to be placed next to each other. This is unlike traditional voltage area layout which separates cells to prevent shorting of power supplies leading to impact on area, routing and power. To implement dRail, a modified standard cell architecture and physical layout is proposed. The methodology is validated by implementing power gating on the data engine in an ARM Cortex-A5 proces...

  17. A Layout for the Carbon Capture with Aqueous Ammonia without Salt Precipitation

    DEFF Research Database (Denmark)

    Bonalumi, Davide; Valenti, Gianluca; Lillia, Stefano

    2016-01-01

    Post-combustion carbon capture technologies seem to be necessary to realize the CO2 mitigation policies internationally shared for the next future, despite none of them appears to be ready for full-scale applications. This work considers the aqueous ammonia based process for a coal-fired Ultra....... The second layout operates at cooled conditions, which does not yield any salt precipitation. The Chilled layout reveals low specific heat duty and SPECCA equal to 2.2 and 2.86 MJ/kgco2, respectively. In contrast, the Cooled layout presents a higher specific heat duty of almost 3 MJ/kgco2 but, importantly...

  18. Efficiency Optimization by Considering the High Voltage Flyback Transformer Parasitics using an Automatic Winding Layout Technique

    DEFF Research Database (Denmark)

    Thummala, Prasanth; Schneider, Henrik; Zhang, Zhe

    2015-01-01

    .The energy efficiency is optimized using a proposed new automatic winding layout (AWL) technique and a comprehensive loss model.The AWL technique generates a large number of transformer winding layouts.The transformer parasitics such as dc resistance, leakage inductance and self-capacitance are calculated...... for each winding layout.An optimization technique is formulated to minimize the sum of energy losses during charge and discharge operations.The efficiency and energy loss distribution results from the optimization routine provide a deep insight into the high voltage transformer designand its impact...

  19. Piping data retrieval system (PDRS): An integrated package to aid piping layout

    International Nuclear Information System (INIS)

    Vyas, K.N.; Sharma, A.; Susandhi, R.; Basu, S.

    1986-01-01

    An integrated package to aid piping layout has been developed and implemented on PDP-11/34 system at Hall 7. The package allows various equipments to be modelled, consisting of primitive equipment components. The equipment layout for the plant can then be reproduced in the form of drawings such as plan, elevation, isometric or perspective. The package has the built in function to perform hidden line removal among equipments. Once the equipment layout is finalised, the package aids in superimposing the piping as per the specified pipe routine. The report discusses the general capabilities and the major input requirements for the package. (author)

  20. A segmentation algorithm based on image projection for complex text layout

    Science.gov (United States)

    Zhu, Wangsheng; Chen, Qin; Wei, Chuanyi; Li, Ziyang

    2017-10-01

    Segmentation algorithm is an important part of layout analysis, considering the efficiency advantage of the top-down approach and the particularity of the object, a breakdown of projection layout segmentation algorithm. Firstly, the algorithm will algorithm first partitions the text image, and divided into several columns, then for each column scanning projection, the text image is divided into several sub regions through multiple projection. The experimental results show that, this method inherits the projection itself and rapid calculation speed, but also can avoid the effect of arc image information page segmentation, and also can accurate segmentation of the text image layout is complex.

  1. A case study of printing industry plant layout for effective production

    Science.gov (United States)

    Viswajit, T.; Teja, T. Ravi; Deepthi, Y. P.

    2017-07-01

    This paper presents the overall picture of the processes happening in printing industry. This research is aimed to improve the plant layout of existing plant. The travel time was reduced by relocating machinery. Relocation is based on systematic layout planning (SLP). The complete process of raw material entering the industry to dispatching of finished product is shown in 3-D Flow diagram. The process happening in each floor explained in detail using Flow Process chart. Travel time is reduced by 25% after modifying existing plant layout.

  2. Spatial differences of cellular origins and in vivo hypoxia modify contractile properties of pulmonary artery smooth muscle cells: lessons for arterial tissue engineering.

    Science.gov (United States)

    Hall, S M; Soueid, A; Smith, T; Brown, R A; Haworth, S G; Mudera, V

    2007-01-01

    Tissue engineering of functional arteries is challenging. Within the pulmonary artery wall, smooth muscle cells (PASMCs) have site-specific developmental and functional phenotypes, reflecting differing contractile roles. The force generated by PASMCs isolated from the inner 25% and outer 50% of the media of intrapulmonary elastic arteries from five normal and eight chronically hypoxic (hypertensive) 14 day-old piglets was quantified in a three-dimensional (3D) collagen construct, using a culture force monitor. Outer medial PASMCs from normal piglets exerted more force (528 +/- 50 dynes) than those of hypoxic piglets (177 +/- 42 dynes; p engineering of major blood vessels.

  3. Layout design process in conventional Brazilian supermarkets Proceso de formulación de layouts en supermercados convencionales en Brasil Processo de formulação de layouts em supermercados convencionais no Brasil

    Directory of Open Access Journals (Sweden)

    Ana Maria Machado Toaldo

    2010-12-01

    Full Text Available The importance of the layout is well known in the performance of supermarket companies. However since there are very few studies on the subject, this research sought to understand the layout design process in conventionally sized supermarkets in the South of Brazil. For this reason an exploratory study was carried out. The choice of this methodology was due to scarceness of accumulated and systematized knowledge. Data were collected by in-depth interviews with a layout supervisor and a store manager in three supermarket chains in the South of Brazil. Results confirm that layout has considerable influence on company performance. A variety of strategies is used by the companies in layouts to make the customer remain in the store longer, make his stay more enjoyable and consequently encourage spending thus bringing about greater profitability. Finally, a theoretical structure of design layout was proposed. The intention of this study is not to be definitive, but to shed light on the subject, which while important, has never been emphasized in marketing studies.Es evidente la importancia del layout en el desempeño de las empresas supermercadistas. Sin embargo, faltan estudios sobre el tema. Pensando en esa laguna, esta investigación tuvo el objetivo principal de entender como es el proceso de formulación de layouts en supermercados de porte convencional en el Sur brasileño. Para eso, se realizó un estudio exploratorio. La decisión de escoger esa metodología fue en consecuencia de la escasez de conocimiento acumulado y sistematizado. Los datos fueron obtenidos por medio de entrevistas en profundidad realizadas con dos informantes en tres redes supermercadistas del sur de Brasil: un supervisor de layout y un gerente de tienda. Los resultados muestran que el layout tiene mucha influencia en el desempeño de la empresa. Por su intermedio, utilizándose una serie de estrategias, las empresas buscan los siguientes objetivos: hacer con que el

  4. Genetic algorithm optimization for dynamic construction site layout planning

    Directory of Open Access Journals (Sweden)

    Farmakis Panagiotis M.

    2018-02-01

    Full Text Available The dynamic construction site layout planning (DCSLP problem refers to the efficient placement and relocation of temporary construction facilities within a dynamically changing construction site environment considering the characteristics of facilities and work interrelationships, the shape and topography of the construction site, and the time-varying project needs. A multi-objective dynamic optimization model is developed for this problem that considers construction and relocation costs of facilities, transportation costs of resources moving from one facility to another or to workplaces, as well as safety and environmental considerations resulting from facilities’ operations and interconnections. The latter considerations are taken into account in the form of preferences or constraints regarding the proximity or remoteness of particular facilities to other facilities or work areas. The analysis of multiple project phases and the dynamic facility relocation from phase to phase highly increases the problem size, which, even in its static form, falls within the NP (for Nondeterministic Polynomial time- hard class of combinatorial optimization problems. For this reason, a genetic algorithm has been implemented for the solution due to its capability to robustly search within a large solution space. Several case studies and operational scenarios have been implemented through the Palisade’s Evolver software for model testing and evaluation. The results indi­cate satisfactory model response to time-varying input data in terms of solution quality and computation time. The model can provide decision support to site managers, allowing them to examine alternative scenarios and fine-tune optimal solutions according to their experience by introducing desirable preferences or constraints in the decision process.

  5. Change of the layout of an office of a metallurgical company: simple projects, big solutions.

    Science.gov (United States)

    Duarte, Luiz Carlos da Silva; Eckhardt, Moacir; da Motta, Giordano Paulo

    2012-01-01

    The posture, a good organization and the proper layout of the environment and workplaces have a positive influence on the income of an employee. To develop the work it is used a methodology that addressed the study phases of the theory involving the subject, description of the current situation, preparation of conceptions, choice of design, implementation and reporting of results. Through the project of "Change of the layout of an office of a metallurgical company" there was an intervention in these reported aspects providing improvements in the office, regarding ergonomic, layout, workplace and lighting issues, bringing welfare to the official, with the intent to improve its performance within the company and facilitating its actions, as the company's customer service. The results provided improvements in layout, in the workplace and especially in comfort for the human resources that perform their activities.

  6. Constraint-aware interior layout exploration for pre-cast concrete-based buildings

    KAUST Repository

    Liu, Han; Yang, Yongliang; AlHalawani, Sawsan; Mitra, Niloy J.

    2013-01-01

    Creating desirable layouts of building interiors is a complex task as designers have to manually adhere to various local and global considerations arising from competing practical and design considerations. In this work, we present an interactive

  7. Coplanar Electrode Layout Optimized for Increased Sensitivity for Electrical Impedance Spectroscopy

    Directory of Open Access Journals (Sweden)

    Casper Hyttel Clausen

    2014-12-01

    Full Text Available This work describes an improvement in the layout of coplanar electrodes for electrical impedance spectroscopy. We have developed, fabricated, and tested an improved electrode layout, which improves the sensitivity of an impedance flow cytometry chip. The improved chip was experimentally tested and compared to a chip with a conventional electrode layout. The improved chip was able to discriminate 0.5 μm beads from 1 μm as opposed to the conventional chip. Furthermore, finite element modeling was used to simulate the improvements in electrical field density and uniformity between the electrodes of the new electrode layout. Good agreement was observed between the model and the obtained experimental results.

  8. Layout Optimization of Structures with Finite-size Features using Multiresolution Analysis

    DEFF Research Database (Denmark)

    Chellappa, S.; Diaz, A. R.; Bendsøe, Martin P.

    2004-01-01

    A scheme for layout optimization in structures with multiple finite-sized heterogeneities is presented. Multiresolution analysis is used to compute reduced operators (stiffness matrices) representing the elastic behavior of material distributions with heterogeneities of sizes that are comparable...

  9. Effects of planar element formulation and numerical integration order on checkerboard material layouts

    CSIR Research Space (South Africa)

    Long, CS

    2009-01-01

    Full Text Available The effects of selected planar finite element formulations, and their associated integration schemes, on the stiffness of a checkerboard material layout are investigated. Standard 4-node bilinear elements, 8- and 9-node quadratic elements, as well...

  10. Validation of the Data Consolidation in Layout Database for the LHC Tunnel Cryogenics Controls Upgrade

    CERN Document Server

    Tovar-Gonzalez, A; Blanco, E; Fortescue-Beck, E; Fluder, C; Inglese, V; Pezzetti, M; Gomes, P; Wolak, T; Dudek, M; Frassinelli, F; Drozd, A; Zapolski, M

    2014-01-01

    The control system of the Large Hadron Collider cryogenics manages over 34’000 instrumentation and actuator channels. The complete information on their characteristics and parameters can be extracted from a set of views on the Layout database, to generate the specifications of the control system; from these, the code to populate PLCs (Programmable Logic Controller) and SCADA (Supervisory Control & Data Acquisition) is automatically produced, within the UNICOS framework (Unified Industrial Control System). The Layout database is, since 2003, progressively integrating and centralizing information on the whole CERN Accelerator complex. It models topographical organization (layouts) as functional positions and relationships. After three years of machine operation, many parameters have been manually adjusted in SCADA and PLCs; they now differ from their original values in the Layout database. Furthermore, to accommodate the upgrade of the UNICOS Continuous Process Control package to version 6, some data stru...

  11. Solving the wind farm layout optimization problem using random search algorithm

    DEFF Research Database (Denmark)

    Feng, Ju; Shen, Wen Zhong

    2015-01-01

    , in which better results than the genetic algorithm (GA) and the old version of the RS algorithm are obtained. Second it is applied to the Horns Rev 1 WF, and the optimized layouts obtain a higher power production than its original layout, both for the real scenario and for two constructed scenarios......Wind farm (WF) layout optimization is to find the optimal positions of wind turbines (WTs) inside a WF, so as to maximize and/or minimize a single objective or multiple objectives, while satisfying certain constraints. In this work, a random search (RS) algorithm based on continuous formulation....... In this application, it is also found that in order to get consistent and reliable optimization results, up to 360 or more sectors for wind direction have to be used. Finally, considering the inevitable inter-annual variations in the wind conditions, the robustness of the optimized layouts against wind condition...

  12. Navigating Comics: An Empirical and Theoretical Approach to Strategies of Reading Comic Page Layouts

    Science.gov (United States)

    Cohn, Neil

    2013-01-01

    Like the sequence of words in written language, comic book page layouts direct images into a deliberate reading sequence. Conventional wisdom would expect that comic panels follow the order of text: left-to-right and down – a “Z-path” – though several layouts can violate this order, such as Gestalt groupings of panels that deny a Z-path of reading. To examine how layouts pressure readers to choose pathways deviating from the Z-path, we presented participants with comic pages empty of content, and asked them to number the panels in the order they would read them. Participants frequently used strategies departing from both the traditional Z-path and Gestalt groupings. These preferences reveal a system of constraints that organizes panels into hierarchic constituents, guiding readers through comic page layouts. PMID:23616776

  13. IC layout adjustment method and tool for improving dielectric reliability at interconnects

    Energy Technology Data Exchange (ETDEWEB)

    Kahng, Andrew B.; Chan, Tuck Boon

    2018-03-20

    Method for adjusting a layout used in making an integrated circuit includes one or more interconnects in the layout that are susceptible to dielectric breakdown are selected. One or more selected interconnects are adjusted to increase via to wire spacing with respect to at least one via and one wire of the one or more selected interconnects. Preferably, the selecting analyzes signal patterns of interconnects, and estimates the stress ratio based on state probability of routed signal nets in the layout. An annotated layout is provided that describes distances by which one or more via or wire segment edges are to be shifted. Adjustments can include thinning and shifting of wire segments, and rotation of vias.

  14. Navigating comics: an empirical and theoretical approach to strategies of reading comic page layouts

    Directory of Open Access Journals (Sweden)

    Neil eCohn

    2013-04-01

    Full Text Available Like the sequence of words in written language, comic book page layouts direct images into a deliberate reading sequence. Conventional wisdom would expect that comic panels follow the order of text: left-to-right and down—a Z-path—though several layouts can violate this order, such as Gestalt groupings of panels that deny a Z-path of reading. To examine how layouts pressure readers to choose pathways deviating from the Z-path, we presented participants with comic pages empty of content, and asked them to number the panels in the order they would read them. Participants frequently used strategies departing from both the traditional Z-path and Gestalt groupings. These preferences reveal a system of constraints that organizes panels into hierarchic constituents, guiding readers through comic page layouts.

  15. Navigating comics: an empirical and theoretical approach to strategies of reading comic page layouts.

    Science.gov (United States)

    Cohn, Neil

    2013-01-01

    Like the sequence of words in written language, comic book page layouts direct images into a deliberate reading sequence. Conventional wisdom would expect that comic panels follow the order of text: left-to-right and down - a "Z-path" - though several layouts can violate this order, such as Gestalt groupings of panels that deny a Z-path of reading. To examine how layouts pressure readers to choose pathways deviating from the Z-path, we presented participants with comic pages empty of content, and asked them to number the panels in the order they would read them. Participants frequently used strategies departing from both the traditional Z-path and Gestalt groupings. These preferences reveal a system of constraints that organizes panels into hierarchic constituents, guiding readers through comic page layouts.

  16. Study of LED layout in indoor visible light communication and performance analysis

    Science.gov (United States)

    Wang, Jiaan; Che, Ying; Wang, Xinlan; Guo, Linyang; Li, Jing

    2017-10-01

    Light emitting diodes(LED) could provide both illumination and data communication in indoor visible light communication(VLC) that owns the modulation bandwith from several from several MHz to seneral hundreds of MHz. The layout of LED plays an important role in maintaining a steady optical power distribution over the receiving plane. The existing rectangular LED layout does not provide a full coverage on the receiving plane leaving receiving optical power outage area, which in turn affects the best performance of the VLC system. This paper design a circular layout scheme of LED in 5mX5mX3m room based on the criterion of the illumination minimum mean square deviation. The influence of the distribution of the intensity of illumination with the radius of 1m and 1.5m,for including the wall reflection and not including the wall reflection, and make a comparison with rectangular LED layout of illumination distribution, when the number of LEDs with rectangular layout as same as circular layout. Including the number of LEDs are 4 and 16.For a specific simulation parameters as following:height of receiving plane is 0.85m,a single LEDs is composed of 60X60 LED chips, the parameters of a single chip is that transmitting power is 20mW,center luminous intensity is 0.73cd.semiangle at half power is 70deg.The parameters of concentrator is that photodiode area is 1cm2,photodiode responsivity is 0.4,field of view at the receiver is 85deg.Other parameters are that reflective index of concentrator is 1.5,reflectivity of wall is 0.8.Circular layout and rectangular layout are analyzed through simulation of the received optical power distribution, signal noise ratio distribution in non line of sight(including the wall reflection) and line of sight(not including the wall reflection),when the number of the LED is different. It is clear from the results that the received optical power distribution of non line of sight is better than line of sight, when the number of the LED are same, but

  17. Peripheral vision benefits spatial learning by guiding eye movements.

    Science.gov (United States)

    Yamamoto, Naohide; Philbeck, John W

    2013-01-01

    The loss of peripheral vision impairs spatial learning and navigation. However, the mechanisms underlying these impairments remain poorly understood. One advantage of having peripheral vision is that objects in an environment are easily detected and readily foveated via eye movements. The present study examined this potential benefit of peripheral vision by investigating whether competent performance in spatial learning requires effective eye movements. In Experiment 1, participants learned room-sized spatial layouts with or without restriction on direct eye movements to objects. Eye movements were restricted by having participants view the objects through small apertures in front of their eyes. Results showed that impeding effective eye movements made subsequent retrieval of spatial memory slower and less accurate. The small apertures also occluded much of the environmental surroundings, but the importance of this kind of occlusion was ruled out in Experiment 2 by showing that participants exhibited intact learning of the same spatial layouts when luminescent objects were viewed in an otherwise dark room. Together, these findings suggest that one of the roles of peripheral vision in spatial learning is to guide eye movements, highlighting the importance of spatial information derived from eye movements for learning environmental layouts.

  18. REPOSITORY LAYOUT SUPPORTING DESIGN FEATURE NO.13 - WASTE PACKAGE SELF SHIELDING

    International Nuclear Information System (INIS)

    Owen, J.

    1999-01-01

    The objective of this analysis is to develop a repository layout, for Feature No. 13, that will accommodate self-shielding waste packages (WP) with an areal mass loading of 25 metric tons of uranium per acre (MTU/acre). The scope of this analysis includes determination of the number of emplacement drifts, amount of emplacement drift excavation required, and a preliminary layout for illustrative purposes

  19. IFMIF - Layout and arrangement of cells according to requirements of technical logistics, reliability and remote handling

    Energy Technology Data Exchange (ETDEWEB)

    Mittwollen, Martin, E-mail: martin.mittwollen@kit.edu [Karlsruhe Institute of Technology, Institute for Conveying Technology and Logistics, Karlsruhe (Germany); Eilert, Dirk; Kubaschewski, Martin; Madzharov, Vladimir [Karlsruhe Institute of Technology, Institute for Conveying Technology and Logistics, Karlsruhe (Germany); Tian Kuo [Karlsruhe Institute of Technology, Institute for Neutron Physics and Reactor Technology, Karlsruhe (Germany)

    2012-08-15

    Highlights: Black-Right-Pointing-Pointer In a first approach, layout and arrangement of the cells followed a predetermined plant layout. Black-Right-Pointing-Pointer Disadvantages in technical logistics, reliability and remote handling have been detected. Black-Right-Pointing-Pointer Deliberation with project teams opened space for improvements. Black-Right-Pointing-Pointer Layout and arrangement of cells have been improved by simplification of design. Black-Right-Pointing-Pointer Speed and reliability have been increased significantly. - Abstract: The International Fusion Material Irradiation Facility (IFMIF) is designed to study and qualify structural and functional materials which shall be used in future fusion nuclear power plants. During the current engineering validation and engineering design activities (EVEDA) phase the development of e.g. an optimized layout and arrangement of the cells (Access Cell, Test Cell, and Test Module Handling Cells) is of major interest. After defining different functions for the individual cells like e.g. large scale/fine scale disassembling of test modules a first layout has been developed. This design followed requirements like having a minimum of carrier changes to avoid sources of failures. On the other hand it has had to be a compact arrangement of cells due to restrictions from plant layout. A row of changes of transfer direction, and different crane systems were the consequence. Constructive discussion with project team results in the statement, that for reasons of being reliable and fast, layout and arrangement of cells goes first, plant layout then will follow. The chance for big improvements was taken and the result was a simplified design with strong reduced number of functional elements, and increased reliability and speed.

  20. Human Factors Analysis and Layout Guideline Development for the Canadian Surface Combatant (CSC) Project

    Science.gov (United States)

    2013-04-01

    layout should be designed to protect personnel from injury during all operating conditions. b. The layout should be designed to accommodate the...which will eventually lead to a major category with three possibilities. As can be seen there are a total of 10 possible ratings. 36 Honey workl...accommodate the size or performance of personnel could result in a hazardous condition leading to personnel injury or equipment damage, the design for all

  1. A study on Store Layout and its impact on Visual Merchandising in Retail Outlet

    OpenAIRE

    Dr. K. R. Mahalaxmi; R. Keerthika

    2018-01-01

    Visual merchandising is the marketing promotion strategy that are implemented in the retail industry by emerging innovative floor plans and three dimensional display using store layout techniques in order to increase the sale. This study examine the store layout strategy in relation to visual merchandising and assist the managers in developing better merchandising techniques for retail stores. This study also helps to find out the analysis the impact of various visual merchandising variables ...

  2. Optimal Stack Layout in a Sea Container Terminal with Automated Lifting Vehicles

    OpenAIRE

    Roy, D.; Gupta, A.; Parhi, S.; de Koster, M.B.M.

    2014-01-01

    textabstractContainer terminal performance is largely determined by its design decisions, which include the number and type of quay cranes (QCs), stack cranes (SCs), transport vehicles, vehicle travel path, and stack layout. The terminal design process is complex because it is affected by factors such as topological constraints, stochastic interactions among the quayside, vehicle transport and stackside operations. Further, the orientation of the stack layout (parallel or perpendicular to the...

  3. Layout Design for a Low Capacity Manufacturing Line: A Case Study

    OpenAIRE

    De Carlo, Filippo; Arleo, Maria Antonietta; Borgia, Orlando; Tucci, Mario

    2013-01-01

    The layout re‐arrangement of fashion production lines realizing many small batches is rarely deployed according to well‐known engineering procedures. In fact, it would often appear too complex to call a plant engineer for the proper layout design of such small production lines. Rather, it is preferred to apply empirical methodologies when considering, generally, factory know‐how, general business needs, safety requirements, and so on. In the present work, the results of a fashion manufacturin...

  4. A study on three dimensional layout design by the simulated annealing method

    International Nuclear Information System (INIS)

    Jang, Seung Ho

    2008-01-01

    Modern engineered products are becoming increasingly complicated and most consumers prefer compact designs. Layout design plays an important role in many engineered products. The objective of this study is to suggest a method to apply the simulated annealing method to the arbitrarily shaped three-dimensional component layout design problem. The suggested method not only optimizes the packing density but also satisfies constraint conditions among the components. The algorithm and its implementation as suggested in this paper are extendable to other research objectives

  5. New layout of time resolved beam energy spectrum measurement for dragon-I

    International Nuclear Information System (INIS)

    Liao Shuqing; Zhang Kaizhi; Shi Jinshui

    2010-01-01

    A new layout of time resolved beam energy spectrum measurement is proposed for Dragon-I by a new method named RBS (rotating beams in solenoids). The basic theory of RBS and the new layout are presented and the measuring error is also discussed. The derived time resolved beam energy spectrum is discrete and is determined by measuring the beam's rotating angle and expanding width through a group of solenoids at the export of Dragon-I. (authors)

  6. The Comparison of Layout Arrangements for the Material Flow Ordering Planning in Production Systems through Simulation Analysis

    Directory of Open Access Journals (Sweden)

    Mehmet AKSARAYLI

    2009-02-01

    Full Text Available Enterprises have to make suitable location planning to decrease their product cost and to increase their productivity in our time. The aim of this study is to compare the basic layout types used in arranging inside facility layout with each other by using simulation. Especially in this study, material handling times between machines and ratio of these times in total times were interested. First of all a new production system is designed to the basic layout types used in arranging inside facility layout. And then in the designed production system, machines are arranged for each machine layout types. Machine layout types are transferred to PROMODEL simulation software. Then with the results of analysis, material handling times of different machine layout types and ratio of material handling times in total production time were compared and the results obtained from this analysis were given after commented on this study.

  7. Systematic Layout Planning of a Radiology Reporting Area to Optimize Radiologists' Performance.

    Science.gov (United States)

    Benitez, Guilherme Brittes; Fogliatto, Flavio Sanson; Cardoso, Ricardo Bertoglio; Torres, Felipe Soares; Faccin, Carlo Sasso; Dora, José Miguel

    2018-04-01

    Optimizing radiologists' performance is a major priority for managers of health services/systems, since the radiologists' reporting activity imposes a severe constraint on radiology productivity. Despite that, methods to optimize radiologists' reporting workplace layout are scarce in the literature. This study was performed in the Radiology Division (RD) of an 850-bed University-based general hospital. The analysis of the reporting workplace layout was carried out using the systematic layout planning (SLP) method, in association with cluster analysis as a complementary tool in early stages of SLP. Radiologists, architects, and hospital managers were the stakeholders consulted for the completion of different stages of the layout planning process. A step-by-step description of the proposed methodology to plan an RD reporting layout is presented. Clusters of radiologists were defined using types of exams reported and their frequency of occurrence as clustering variables. Sectors with high degree of interaction were placed in proximity in the new RD layout, with separation of noisy and quiet areas. Four reporting cells were positioned in the quiet area, grouping radiologists by subspecialty, as follows: cluster 1-abdomen; cluster 2-musculoskeletal; cluster 3-neurological, vascular and head & neck; cluster 4-thoracic and cardiac. The creation of reporting cells has the potential to limit unplanned interruptions and enhance the exchange of knowledge and information within cells, joining radiologists with the same expertise. That should lead to improvements in productivity, allowing managers to more easily monitor radiologists' performance.

  8. a Preliminary Work on Layout Slam for Reconstruction of Indoor Corridor Environments

    Science.gov (United States)

    Baligh Jahromi, A.; Sohn, G.; Shahbazi, M.; Kang, J.

    2017-09-01

    We propose a real time indoor corridor layout estimation method based on visual Simultaneous Localization and Mapping (SLAM). The proposed method adopts the Manhattan World Assumption at indoor spaces and uses the detected single image straight line segments and their corresponding orthogonal vanishing points to improve the feature matching scheme in the adopted visual SLAM system. Using the proposed real time indoor corridor layout estimation method, the system is able to build an online sparse map of structural corner point features. The challenges presented by abrupt camera rotation in the 3D space are successfully handled through matching vanishing directions of consecutive video frames on the Gaussian sphere. Using the single image based indoor layout features for initializing the system, permitted the proposed method to perform real time layout estimation and camera localization in indoor corridor areas. For layout structural corner points matching, we adopted features which are invariant under scale, translation, and rotation. We proposed a new feature matching cost function which considers both local and global context information. The cost function consists of a unary term, which measures pixel to pixel orientation differences of the matched corners, and a binary term, which measures the amount of angle differences between directly connected layout corner features. We have performed the experiments on real scenes at York University campus buildings and the available RAWSEEDS dataset. The incoming results depict that the proposed method robustly performs along with producing very limited position and orientation errors.

  9. Learning Building Layouts with Non-geometric Visual Information: The Effects of Visual Impairment and Age

    Science.gov (United States)

    Kalia, Amy A.; Legge, Gordon E.; Giudice, Nicholas A.

    2009-01-01

    Previous studies suggest that humans rely on geometric visual information (hallway structure) rather than non-geometric visual information (e.g., doors, signs and lighting) for acquiring cognitive maps of novel indoor layouts. This study asked whether visual impairment and age affect reliance on non-geometric visual information for layout learning. We tested three groups of participants—younger (sighted, older (50–70 years) normally sighted, and low vision (people with heterogeneous forms of visual impairment ranging in age from 18–67). Participants learned target locations in building layouts using four presentation modes: a desktop virtual environment (VE) displaying only geometric cues (Sparse VE), a VE displaying both geometric and non-geometric cues (Photorealistic VE), a Map, and a Real building. Layout knowledge was assessed by map drawing and by asking participants to walk to specified targets in the real space. Results indicate that low-vision and older normally-sighted participants relied on additional non-geometric information to accurately learn layouts. In conclusion, visual impairment and age may result in reduced perceptual and/or memory processing that makes it difficult to learn layouts without non-geometric visual information. PMID:19189732

  10. Exploring the Effects of Pitch Layout on Learning a New Musical Instrument

    Directory of Open Access Journals (Sweden)

    Jennifer MacRitchie

    2017-11-01

    Full Text Available Although isomorphic pitch layouts are proposed to afford various advantages for musicians playing new musical instruments, this paper details the first substantive set of empirical tests on how two fundamental aspects of isomorphic pitch layouts affect motor learning: shear, which makes the pitch axis vertical, and the adjacency (or nonadjacency of pitches a major second apart. After receiving audio-visual training tasks for a scale and arpeggios, performance accuracies of 24 experienced musicians were assessed in immediate retention tasks (same as the training tasks, but without the audio-visual guidance and in a transfer task (performance of a previously untrained nursery rhyme. Each participant performed the same tasks with three different pitch layouts and, in total, four different layouts were tested. Results show that, so long as the performance ceiling has not already been reached (due to ease of the task or repeated practice, adjacency strongly improves performance accuracy in the training and retention tasks. They also show that shearing the layout, to make the pitch axis vertical, worsens performance accuracy for the training tasks but, crucially, it strongly improves performance accuracy in the transfer task when the participant needs to perform a new, but related, task. These results can inform the design of pitch layouts in new musical instruments.

  11. Improvement of productivity in low volume production industry layout by using witness simulation software

    Science.gov (United States)

    Jaffrey, V.; Mohamed, N. M. Z. N.; Rose, A. N. M.

    2017-10-01

    In almost all manufacturing industry, increased productivity and better efficiency of the production line are the most important goals. Most factories especially small scale factory has less awareness of manufacturing system optimization and lack of knowledge about it and uses the traditional way of management. Problems that are commonly identified in the factory are a high idle time of labour and also small production. This study is done in a Small and Medium Enterprises (SME) low volume production company. Data collection and problems affecting productivity and efficiency are identified. In this study, Witness simulation software is being used to simulate the layout and the output is focusing on the improvement of layout in terms of productivity and efficiency. In this study, the layout is rearranged by reducing the travel time from a workstation to another workstation. Then, the improved layout is modelled and the machine and labour statistic of both, original and improved layout is taken. Productivity and efficiency are calculated for both layout and then being compared.

  12. Using RGB-D sensors and evolutionary algorithms for the optimization of workstation layouts.

    Science.gov (United States)

    Diego-Mas, Jose Antonio; Poveda-Bautista, Rocio; Garzon-Leal, Diana

    2017-11-01

    RGB-D sensors can collect postural data in an automatized way. However, the application of these devices in real work environments requires overcoming problems such as lack of accuracy or body parts' occlusion. This work presents the use of RGB-D sensors and genetic algorithms for the optimization of workstation layouts. RGB-D sensors are used to capture workers' movements when they reach objects on workbenches. Collected data are then used to optimize workstation layout by means of genetic algorithms considering multiple ergonomic criteria. Results show that typical drawbacks of using RGB-D sensors for body tracking are not a problem for this application, and that the combination with intelligent algorithms can automatize the layout design process. The procedure described can be used to automatically suggest new layouts when workers or processes of production change, to adapt layouts to specific workers based on their ways to do the tasks, or to obtain layouts simultaneously optimized for several production processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Conceptual Layout of an AHR Building and Facilities

    International Nuclear Information System (INIS)

    Ryu, Jeong-Soo; Chae, Hee-Taek; Park, Cheol

    2007-01-01

    a 20 MWth. In this study some descriptions on the conceptual layout and basic design features of the reference AHR building and facilities with a 20MW are given

  14. About the inevitable compromise between spatial resolution and accuracy of strain measurement for bone tissue: a 3D zero-strain study.

    Science.gov (United States)

    Dall'Ara, E; Barber, D; Viceconti, M

    2014-09-22

    The accurate measurement of local strain is necessary to study bone mechanics and to validate micro computed tomography (µCT) based finite element (FE) models at the tissue scale. Digital volume correlation (DVC) has been used to provide a volumetric estimation of local strain in trabecular bone sample with a reasonable accuracy. However, nothing has been reported so far for µCT based analysis of cortical bone. The goal of this study was to evaluate accuracy and precision of a deformable registration method for prediction of local zero-strains in bovine cortical and trabecular bone samples. The accuracy and precision were analyzed by comparing scans virtually displaced, repeated scans without any repositioning of the sample in the scanner and repeated scans with repositioning of the samples. The analysis showed that both precision and accuracy errors decrease with increasing the size of the region analyzed, by following power laws. The main source of error was found to be the intrinsic noise of the images compared to the others investigated. The results, once extrapolated for larger regions of interest that are typically used in the literature, were in most cases better than the ones previously reported. For a nodal spacing equal to 50 voxels (498 µm), the accuracy and precision ranges were 425-692 µε and 202-394 µε, respectively. In conclusion, it was shown that the proposed method can be used to study the local deformation of cortical and trabecular bone loaded beyond yield, if a sufficiently high nodal spacing is used. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. Built environmental factors and adults' travel behaviors: Role of street layout and local destinations.

    Science.gov (United States)

    Koohsari, Mohammad Javad; Owen, Neville; Cole, Rachel; Mavoa, Suzanne; Oka, Koichiro; Hanibuchi, Tomoya; Sugiyama, Takemi

    2017-03-01

    Street layout is consistently associated with adults' travel behaviors, however factors influencing this association are unclear. We examined associations of street layout with travel behaviors: walking for transport (WT) and car use; and, the extent to which these relationships may be accounted for by availability of local destinations. A 24-h travel diary was completed in 2009 by 16,345 adult participants of the South-East Queensland Household Travel Survey, Australia. Three travel-behavior outcomes were derived: any home-based WT; over 30min of home-based WT; and, over 60min of car use. For street layout, a space syntax measure of street integration was calculated for each Statistical Area 1 (SA1, the smallest geographic unit in Australia). An objective measure of availability of destinations - Walk Score - was also derived for each SA1. Logistic regression examined associations of street layout with travel behaviors. Mediation analyses examined to what extent availability of destinations explained the associations. Street integration was significantly associated with travel behaviors. Each one-decile increment in street integration was associated with an 18% (95%CI: 1.15, 1.21) higher odds of any home-based WT; a 10% (95%CI: 1.06, 1.15) higher odds of over 30min of home-based WT; and a 5% (95%CI: 0.94, 0.96) lower odds of using a car over 60min. Local destinations partially mediated the effects of street layout on travel behaviors. Well-connected street layout contributes to active travel partially through availability of more local destinations. Urban design strategies need to address street layout and destinations to promote active travel among residents. Copyright © 2016 Elsevier Inc. All rights reserved.

  16. Utilization of reduced fuelling ripple set in ROP detector layout optimization

    International Nuclear Information System (INIS)

    Kastanya, Doddy

    2012-01-01

    Highlights: ► ADORE is an ROP detect layout optimization algorithm in CANDU reactors. ► The effect of using reduced set of fuelling ripples in ADORE is assessed. ► Significant speedup can be realized by adopting this approach. ► The quality of the results is comparable to results from full set of ripples. - Abstract: The ADORE (Alternative Detector layout Optimization for REgional overpower protection system) algorithm for performing the optimization of regional overpower protection (ROP) for CANDU® reactors has been recently developed. This algorithm utilizes the simulated annealing (SA) stochastic optimization technique to come up with an optimized detector layout for the ROP systems. For each history in the SA iteration where a particular detector layout is evaluated, the goodness of this detector layout is measured in terms of its trip set point value which is obtained by performing a probabilistic trip set point calculation using the ROVER-F code. Since during each optimization execution thousands of candidate detector layouts are evaluated, the overall optimization process is time consuming. Since for each ROVER-F evaluation the number of fuelling ripples controls the execution time, reducing the number of fuelling ripples will reduce the overall execution time. This approach has been investigated and the results are presented in this paper. The challenge is to construct a set of representative fuelling ripples which will significantly speedup the optimization process while guaranteeing that the resulting detector layout has similar quality to the ones produced when the complete set of fuelling ripples is employed.

  17. New shipyard layout design for the preliminary phase & case study for the green field project

    Science.gov (United States)

    Song, Young Joo; Woo, Jong Hun

    2013-03-01

    For several decades, Asian nations such as Korea, Japan and China have been leading the shipbuilding industry since the decline in Europe and America. However, several developing countries such as India, Brazil, etc. are going to make an entrance into the shipbuilding industry. These developing countries are finding technical partners or information providers because they are in situation of little experiences and technologies. Now, the shipbuilding engineering companies of shipbuilding advanced countries are getting a chance of engineering business against those developing countries. The starting point of this business model is green field project for the construction of new shipyard. This business model is started with a design of the shipyard layout. For the conducting of the shipyard layout design, four kinds of engineering parts are required. Those are civil engineering, building engineering, utility engineering and production layout engineering. Among these parts, production layout engineering is most important because its result is the foundation of the other engineering parts and it determines the shipyard capacity during the shipyard operation lifecycle. Previous researches about the shipyard layout design are out of the range from the business requirements because most research cases are in the tower of ivory, which means that there are little consideration of real ship and shipbuilding operation. In this paper, a shipyard layout design for preliminary phase is conducted for the target of newly planned shipyard at Venezuela of South America with an integrated method that is capable of dealing with actual master data from the shipyard. The layout design method of this paper is differentiated from the previous researches in that the actual product data from the target ship and the actual shipbuilding operation data are used for the required area estimation.

  18. New shipyard layout design for the preliminary phase & case study for the green field project

    Directory of Open Access Journals (Sweden)

    Young Joo Song

    2013-03-01

    Full Text Available For several decades, Asian nations such as Korea, Japan and China have been leading the shipbuilding industry since the decline in Europe and America. However, several developing countries such as India, Brazil, etc. are going to make an entrance into the shipbuilding industry. These developing countries are finding technical partners or information providers because they are in situation of little experiences and technologies. Now, the shipbuilding engineering companies of shipbuilding advanced countries are getting a chance of engineering business against those developing countries. The starting point of this business model is green field project for the construction of new shipyard. This business model is started with a design of the shipyard layout. For the conducting of the shipyard layout design, four kinds of engineering parts are required. Those are civil engineering, building engineering, utility engineering and production layout engineering. Among these parts, production layout engineering is most important because its result is the foundation of the other engineering parts and it determines the shipyard capacity during the shipyard operation lifecycle. Previous researches about the shipyard layout design are out of the range from the business requirements because most research cases are in the tower of ivory, which means that there are little consideration of real ship and shipbuilding operation. In this paper, a shipyard layout design for preliminary phase is conducted for the target of newly planned shipyard at Venezuela of South America with an integrated method that is capable of dealing with actual master data from the shipyard. The layout design method of this paper is differentiated from the previous researches in that the actual product data from the target ship and the actual shipbuilding operation data are used for the required area estimation.

  19. Why should we pay more for layout designers?

    Science.gov (United States)

    Khan, Samee U.

    2003-12-01

    In this paper, we discuss the Passive Optical Network (PON) deployment on an arbitrary grid with guarenteed p-1 equipment failure. We show that this problem in general is NP-hard. We propose an algorithm, which guarantees a solution of 4-approximation to the optimal deployment, and further argue that this is the best lower bound achievable in our case.A basic architecture of PON is shown in figure 1.The main component of PON is an optical splitter device. Depending on which direction the light is travelling, it splits the incoming light and distributes it to multiple fibers towards Optical Network Termination (ONT), or combines it into one towards Optical Line Terminal (OLT). The PON technology uses a double-star architecture. The first star topology centers at the OLT, and the second at the optical splitter. PROBLEM DESCRIPTION: We can formulate the problem of optimal p-1 fault-tolerent PON Network Layout (PNL)as a graph theoretical problem. Consider a graph G(V,E), such that V represent the physical locations of the subscriber's, CO, and another location acquired by the CO to expand its network, and E represent the communication lines between two Vi's. If there is no direct communication line c(i,j) between Vi and Vj, we consider the shortest path between them measured in terms of simple distance or cost constraints. Without the loss of generality we assume that c(i,j)=c(j,i). For simplicity we do not further sub-divide V into the obvious categories that represent the locations of OLT, ONT, CO, optical splitters and the subscribers. We can now formulate the PNL problem as follows: "Given an undirected graph G, find the locations of ONTs and splitters such that the cost of the equipment is minimized and for QoS the maximum distance from an ONT to the pth splitter and from a splitter to the pth OLT is minimized". We assume that the OLT is residing inside the CO. The problem definition does not consider the optimization of ONT to the customer premises. This is due

  20. Progress on building design and site layout, and preparation for procurement

    International Nuclear Information System (INIS)

    Haange, R.

    2004-01-01

    The ITER site layout and buildings retain many of the major features worked out for the original 1998 design of ITER. By mid-2001, the design had been adjusted to take account of the reductions in size of the tokamak and in the performance and capability of its supporting plant systems, with a view to providing a building construction cost reduction near the target of 50%. The present status of the site layout and buildings is that, with the exception of the hot cell building, designs are available for the ITER buildings and site layout, in different degrees of detail, ready for final review as soon as the drawings and 3D models have been updated. The ITER site layout is determined by the functions of the various plant systems provided in support of the ITER tokamak. These systems are located in different buildings on the ITER site. Changes in the plant layout inside buildings can, therefore, have an important impact on the overall site layout. The general layout of the site assumes electrical power comes in from the west, heat rejection is on the east, access into the main building for assembly is from the south, and removal of waste is from the north. These orientations are purely notional, determining only the relative positions. Both the European and Japanese potential ITER sites will most likely use seismic isolation of the main tokamak complex. As a result, the detailed design of these buildings and in particular the piping connections to them developed for the 'generic' ITER site will require redesign. Also, the footprint of the main tokamak complex will increase, and hence the layout of the utility tunnel network will have to be updated. A draft Site Facilities Procurement Specification has been written by the International Team. This will require considerable specific input when the site has been selected. Furthermore, the present site layout will have to be reviewed in detail. The generic site has been kept compact. Once a site is available, it may be

  1. Layout de teclado para uma prancha de comunicação alternativa e ampliada Keyboard layout for an augmentative and alternative communication board

    Directory of Open Access Journals (Sweden)

    Luciane Aparecida Liegel

    2008-12-01

    Full Text Available O objetivo deste artigo é descrever e discutir a proposta de um novo layout de teclado projetado especialmente para uma prancha de comunicação alternativa com acionamento mecânico e remoto, para ser utilizado por portadores de paralisia cerebral com capacidade cognitiva preservada. Para compor o layout do teclado de comunicação alternativa, realizou-se uma pesquisa envolvendo disposição e conteúdo das teclas. Participaram do estudo onze voluntárias, sendo: cinco professoras de educação especial, quatro pedagogas especializadas em educação especial e duas fonoaudiólogas. O layout é composto por 95 teclas dispostas em grupos de teclas: alfabéticas, de letras acentuadas, numéricas, de funções e de comunicação alternativa e ampliada. As teclas de comunicação alternativa, contêm ícones associados à palavras ou frases, além de teclas acentuadas. Os ícones contemplados fazem parte de uma linguagem visual brasileira de comunicação, em desenvolvimento. Para auxiliar na localização, tanto o tamanho de teclas e caracteres quanto as cores de fundo das teclas diferenciadas foram utilizadas. As teclas com letras acentuadas e as teclas de comunicação alternativa visam facilitar e acelerar a digitação das mensagens, reduzindo assim o tempo de digitação e conseqüentemente, a ocorrência de fadiga muscular.The aim of this article is to describe and discuss a novel layout proposal for keyboard especially designed for a communication board using mechanical and remote activation to be used by people with cerebral paralysis who present sufficient cognitive skills. In order to design the layout of the augmentative and alternative communication keyboard, a research study involving position and content of the keys was undertaken. Eleven volunteers participated in the study, and they were: five special education teachers, four pedagogues specialized in special education and two speech and language therapists. The layout is made up

  2. Impact of Furniture Layout on Indoor Daylighting Performance in Existing Residential Buildings in Malaysia

    Directory of Open Access Journals (Sweden)

    Seyed Mohammad Mousavi

    2018-06-01

    Full Text Available Currently, home-based computing workspaces have developed substantially all over the world, especially in Malaysia. This growing trend attracts computer workers to run a business from their residential units. Hence, visual comfort needs to be considered in addition to thermal comfort for home workers in their residential working rooms. While such rooms are always occupied with furniture, the layout of the furniture may influence the indoor daylighting distribution. Several various furniture layouts can be arranged in a residential working room. However, to have better generalisation, this study focused on the impacts of mostly-used-furniture-layouts (MUFLs on indoor daylighting performance in residential working rooms. The field measurement was conducted in a typically furnished room under a tropical sky to validate the results of the simulation software under different sky conditions. Then, daylight ratio (DR, as a quantitative daylighting variable, and the illuminance uniformity ratio (IUR, CIE glare index (CGI, and Guth visual comfort probability (GVCP, as qualitative daylighting variables, were analysed through simulation experiments. In conclusion, by changing the furniture layout, daylight uniformity recorded the highest fluctuations in the case room among all variables. While various furniture layouts, in a residential working room in the tropics, may even slightly reduce the extreme indoor daylight quantity, they can worsen the indoor daylight quality compared to an unfurnished space. The paper shows that furniture as an interior design parameter cannot help to improve tropical daylighting performance in a building.

  3. Conversion of KEGG metabolic pathways to SBGN maps including automatic layout.

    Science.gov (United States)

    Czauderna, Tobias; Wybrow, Michael; Marriott, Kim; Schreiber, Falk

    2013-08-16

    Biologists make frequent use of databases containing large and complex biological networks. One popular database is the Kyoto Encyclopedia of Genes and Genomes (KEGG) which uses its own graphical representation and manual layout for pathways. While some general drawing conventions exist for biological networks, arbitrary graphical representations are very common. Recently, a new standard has been established for displaying biological processes, the Systems Biology Graphical Notation (SBGN), which aims to unify the look of such maps. Ideally, online repositories such as KEGG would automatically provide networks in a variety of notations including SBGN. Unfortunately, this is non-trivial, since converting between notations may add, remove or otherwise alter map elements so that the existing layout cannot be simply reused. Here we describe a methodology for automatic translation of KEGG metabolic pathways into the SBGN format. We infer important properties of the KEGG layout and treat these as layout constraints that are maintained during the conversion to SBGN maps. This allows for the drawing and layout conventions of SBGN to be followed while creating maps that are still recognizably the original KEGG pathways. This article details the steps in this process and provides examples of the final result.

  4. Efficient Digital Signage-Based Online Store Layout: An Experimental Study

    Directory of Open Access Journals (Sweden)

    Muhammad Fazal Ijaz

    2016-05-01

    Full Text Available In today’s era of information technology, human computer interaction and interface design are critical factors for a successful retail business. In a virtual world, the purpose of store layout is to create an environment that fascinates customers, entices them to spend more time in the store and encourages them to purchase from the store. The accomplishment of a successful retail business relies on a quick response and the adoption of new technologies that simplify the customer’s shopping experience. Virtual stores play a vital role in enhancing the success of a retail business. Nowadays, digital signage is widely used to publicize different store contents. The aim of this paper is to select a distinct layout that can be used in digital signage. To enhance Customer Relationship Management (CRM, digital signage can be installed in various contexts, such as metro stations, shopping centers, airplane terminals, and so on. The proposed system scans the Quick Response (QR code of a product, and the product then arrives at the user end. The tree, pipeline and guiding pathway layouts are employed in the context of digital signage. A questionnaire is used to determine customers’ opinions on the most efficient layout. The statistical results show that layout significantly affects customer’s behavior. Moreover, human computer interaction can help understand more about the customer’s interaction with digital signage.

  5. The Systems Biology Markup Language (SBML) Level 3 Package: Layout, Version 1 Core.

    Science.gov (United States)

    Gauges, Ralph; Rost, Ursula; Sahle, Sven; Wengler, Katja; Bergmann, Frank Thomas

    2015-09-04

    Many software tools provide facilities for depicting reaction network diagrams in a visual form. Two aspects of such a visual diagram can be distinguished: the layout (i.e.: the positioning and connections) of the elements in the diagram, and the graphical form of the elements (for example, the glyphs used for symbols, the properties of the lines connecting them, and so on). For software tools that also read and write models in SBML (Systems Biology Markup Language) format, a common need is to store the network diagram together with the SBML representation of the model. This in turn raises the question of how to encode the layout and the rendering of these diagrams. The SBML Level 3 Version 1 Core specification does not provide a mechanism for explicitly encoding diagrams, but it does provide a mechanism for SBML packages to extend the Core specification and add additional syntactical constructs. The Layout package for SBML Level 3 adds the necessary features to SBML so that diagram layouts can be encoded in SBML files, and a companion package called SBML Rendering specifies how the graphical rendering of elements can be encoded. The SBML Layout package is based on the principle that reaction network diagrams should be described as representations of entities such as species and reactions (with direct links to the underlying SBML elements), and not as arbitrary drawings or graphs; for this reason, existing languages for the description of vector drawings (such as SVG) or general graphs (such as GraphML) cannot be used.

  6. CONTRIBUTION OF COMPUTATIONAL SIMULATION FOR LAYOUT ANALYSIS IN A WOODEN FURNITURE INDUSTRY

    Directory of Open Access Journals (Sweden)

    Alexandre Navarro Silva

    Full Text Available ABSTRACT The objective of this study was to balance the production line and analyze the layout of the sewing sector in a furniture industry. Using the Arena software, a simulation model was constructed that represented the real system consisting of a cellular layout with 3 groups of 5 seamstresses, who produced 57 different types of products divided into three families, in a daily working day of 625 minutes in the months of February to August and 725 minutes in the months of September to January. The model was quantitatively validated among the managers of the studied industry. The obtained results allowed conclusions with an error of less than 1% in the daily quantity of pieces produced with 99% statistical confidence. Therefore, three scenarios related to the organization of the work environment and the balancing of the production line were constructed, and those include: i linear layout, and the balancing allowed the division of five seamstresses for families 1 and 2, and three seamstresses for family 3; ii study of the layout by processes, so that the best balance was constituted of two groups with seven seamstresses; iii similar to scenario 2 but with six seamstresses in group 1 and seven seamstresses in group 2. It was verified that the modified, alternative scenario 2 is more advantageous for the organization, since it presents greater productivity compared to all other scenarios and to the real system, so the company can increase its production capacity by simply modifying the layout and organizing the work environment.

  7. Design optimization of highly asymmetrical layouts by 2D contour metrology

    Science.gov (United States)

    Hu, C. M.; Lo, Fred; Yang, Elvis; Yang, T. H.; Chen, K. C.

    2018-03-01

    As design pitch shrinks to the resolution limit of up-to-date optical lithography technology, the Critical Dimension (CD) variation tolerance has been dramatically decreased for ensuring the functionality of device. One of critical challenges associates with the narrower CD tolerance for whole chip area is the proximity effect control on asymmetrical layout environments. To fulfill the tight CD control of complex features, the Critical Dimension Scanning Electron Microscope (CD-SEM) based measurement results for qualifying process window and establishing the Optical Proximity Correction (OPC) model become insufficient, thus 2D contour extraction technique [1-5] has been an increasingly important approach for complementing the insufficiencies of traditional CD measurement algorithm. To alleviate the long cycle time and high cost penalties for product verification, manufacturing requirements are better to be well handled at design stage to improve the quality and yield of ICs. In this work, in-house 2D contour extraction platform was established for layout design optimization of 39nm half-pitch Self-Aligned Double Patterning (SADP) process layer. Combining with the adoption of Process Variation Band Index (PVBI), the contour extraction platform enables layout optimization speedup as comparing to traditional methods. The capabilities of identifying and handling lithography hotspots in complex layout environments of 2D contour extraction platform allow process window aware layout optimization to meet the manufacturing requirements.

  8. Production facility layout by comparing moment displacement using BLOCPLAN and ALDEP Algorithms

    Science.gov (United States)

    Tambunan, M.; Ginting, E.; Sari, R. M.

    2018-02-01

    Production floor layout settings include the organizing of machinery, materials, and all the equipments used in the production process in the available area. PT. XYZ is a company that manufactures rubber and rubber compounds for retreading tire threaded with hot and cold cooking system. In the production of PT. XYZ is divided into three interrelated parts, namely Masterbatch Department, Department Compound, and Procured Thread Line Department. PT. XYZ has a production process with material flow is irregular and the arrangement of machine is complicated and need to be redesigned. The purpose of this study is comparing movement displacement using BLOCPLAN and ALDEP algorithm in order to redesign existing layout. Redesigning the layout of the production floor is done by applying algorithms of BLOCPLAN and ALDEP. The algorithm used to find the best layout design by comparing the moment displacement and the flow pattern. Moment displacement on the floor layout of the company’s production currently amounts to 2,090,578.5 meters per year and material flow pattern is irregular. Based on the calculation, the moment displacement for the BLOCPLAN is 1,551,344.82 meter per year and ALDEP is 1,600,179 meter per year. Flow Material resulted is in the form of straight the line.

  9. RELOCATION OF HOME APPLIANCES FACTORY BY USING SYSTEMATICAL LAYOUT PLANNING (SLP COMBINED WITH FLOW ANALYSIS AND ASSEMBLY PROCESS DESIGN

    Directory of Open Access Journals (Sweden)

    Yosef Adji Baskoro

    2011-12-01

    Full Text Available Every manufacturing company must have experiencing building a layout. Fred.E Meyers has stated that only death and taxes are certain, there exist a third certainty-a plant layout will change, thus many methods to generate layout are established and each has its own purposes and benefits. This research focused on the design of manufacturing facilities supported by in-depth analysis of Assembly process design with a high stresses on the Systematical Layout Planning ( SLP and Flow Analysis method to facilitate an outcome of layout accordingly to the system needs. This is a real case study conducts with an objective of generating a recommendation layout for Home Appliances Company specifically for television plant

  10. Planning the base station layout in UMTS urban scenarios: a simulation approach to coverage and capacity estimation

    OpenAIRE

    Zola, Enrica Valeria; Barceló Arroyo, Francisco

    2004-01-01

    This paper analyzes the performance of a base station layout for a UMTS network in a densely populated city. The study is carried out using snapshot simulations of an actual city (Barcelona, Spain) with specific traffic and propagation profiles. A first layout is proposed in order to guarantee good coverage with a minimum number of base stations. This layout is approached taking into account the link budget analytical calculations and the first simulation results for a single-cell environment...

  11. Layout of PWR in-core instrumentation system tubing and support structure with Bechtel 3D-CADD

    International Nuclear Information System (INIS)

    Ichikawa, T.; Pfeifer, B.W.; Mulay, J.N.

    1987-01-01

    The optimization study of the PWR In-Core Instrumentation System (ICIS) tubing layout and support structure presented an opportunity to utilize the Bechtel 3D-CADD program to perform this task. This paper provides a brief summary of the Bechtel 3D-CADD program development and capabilities and outlines the process of developing and optimizing the ICIS tube layout. Specific aspects relating to the ICIS tube layout criteria, support, alignment, electronic interference check and erection sequence are provided. (orig.)

  12. Using ProModel as a simulation tools to assist plant layout design and planning: Case study plastic packaging factory

    OpenAIRE

    Pochamarn Tearwattanarattikal; Suwadee Namphacharoen; Chonthicha Chamrasporn

    2008-01-01

    This study is about the application of a Simulation Model to assist decision making on expanding capacity and plant layout design and planning. The plant layout design concept is performed first to create the physical layouts then the simulation model used to test the capability of plant to meet various demand forecast scena. The study employed ProModel package as a tool, using the model to compare the performances in term of % utilization, characteristics of WIP and ability to meet due date....

  13. Optimisation for offshore wind farm cable connection layout using adaptive particle swarm optimisation minimum spanning tree method

    DEFF Research Database (Denmark)

    Hou, Peng; Hu, Weihao; Chen, Zhe

    2016-01-01

    operational requirement and this constraint should be considered during the MST formulation process. Hence, traditional MST algorithm cannot ensure a minimal cable investment layout. In this paper, a new method to optimize the offshore wind farm cable connection layout is presented. The algorithm...... with the optimized cable connection layout. The proposed method is compared with the MST and Dynamic MST (DMST) methods and simulation results show the effectiveness of the proposed method....

  14. Model-based strategy for cell culture seed train layout verified at lab scale.

    Science.gov (United States)

    Kern, Simon; Platas-Barradas, Oscar; Pörtner, Ralf; Frahm, Björn

    2016-08-01

    Cell culture seed trains-the generation of a sufficient viable cell number for the inoculation of the production scale bioreactor, starting from incubator scale-are time- and cost-intensive. Accordingly, a seed train offers potential for optimization regarding its layout and the corresponding proceedings. A tool has been developed to determine the optimal points in time for cell passaging from one scale into the next and it has been applied to two different cell lines at lab scale, AGE1.HN AAT and CHO-K1. For evaluation, experimental seed train realization has been evaluated in comparison to its layout. In case of the AGE1.HN AAT cell line, the results have also been compared to the formerly manually designed seed train. The tool provides the same seed train layout based on the data of only two batches.

  15. A spectral algorithm for fast de novo layout of uncorrected long nanopore reads.

    Science.gov (United States)

    Recanati, Antoine; Brüls, Thomas; d'Aspremont, Alexandre

    2017-10-15

    New long read sequencers promise to transform sequencing and genome assembly by producing reads tens of kilobases long. However, their high error rate significantly complicates assembly and requires expensive correction steps to layout the reads using standard assembly engines. We present an original and efficient spectral algorithm to layout the uncorrected nanopore reads, and its seamless integration into a straightforward overlap/layout/consensus (OLC) assembly scheme. The method is shown to assemble Oxford Nanopore reads from several bacterial genomes into good quality (∼99% identity to the reference) genome-sized contigs, while yielding more fragmented assemblies from the eukaryotic microbe Sacharomyces cerevisiae. https://github.com/antrec/spectrassembler. antoine.recanati@inria.fr. Supplementary data are available at Bioinformatics online. © The Author (2017). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com

  16. Effects of scene content and layout on the perceived light direction in 3D spaces.

    Science.gov (United States)

    Xia, Ling; Pont, Sylvia C; Heynderickx, Ingrid

    2016-08-01

    The lighting and furnishing of an interior space (i.e., the reflectance of its materials, the geometries of the furnishings, and their arrangement) determine the appearance of this space. Conversely, human observers infer lighting properties from the space's appearance. We conducted two psychophysical experiments to investigate how the perception of the light direction is influenced by a scene's objects and their layout using real scenes. In the first experiment, we confirmed that the shape of the objects in the scene and the scene layout influence the perceived light direction. In the second experiment, we systematically investigated how specific shape properties influenced the estimation of the light direction. The results showed that increasing the number of visible faces of an object, ultimately using globally spherical shapes in the scene, supported the veridicality of the estimated light direction. Furthermore, symmetric arrangements in the scene improved the estimation of the tilt direction. Thus, human perception of light should integrally consider materials, scene content, and layout.

  17. Investigating Effects of Screen Layout Elements on Interface and Screen Design Aesthetics

    Directory of Open Access Journals (Sweden)

    Ahamed Altaboli

    2011-01-01

    Full Text Available A recent study suggested the use of the screen layout elements of balance, unity, and sequence as a part of a computational model of interface aesthetics. It is argued that these three elements are the most contributed terms in the model. In the current study, a controlled experiment was designed and conducted to systematically investigate effects of these three elements (balance, unity, and sequence on the perceived interface aesthetics. Results showed that the three elements have significant effects on the perceived interface aesthetics. Significant interactions were also found among the three elements. A regression model relating the perceived visual aesthetics to the three elements was constructed. When validating the model using standard questionnaire scores of real web pages, high correlations were found between the values computed by the model and scores of questionnaire items related to visual layout of the web pages, indicating that layout-based measures are good at assessing the classical dimension of website aesthetics.

  18. Cadence® High-Speed PCB Layout Flow Workshop

    CERN Document Server

    2003-01-01

    Last release of Cadence High-Speed PCB Design methodology (PE142) based on Concept-HDL schematic editor, Constraint Manager, SPECCTRAQuest signal integrity analysis tool and ALLEGRO layout associated with SPECCTRA auto router tools, is now enough developed and stable to be taken into account for high-speed board designs at CERN. The implementation of this methodology, build around the new Constraint Manager program, is essential when you have to develop a board having a lot of high-speed design rules such as terminated lines, large bus structures, maximum length, timing, crosstalk etc.. that could not be under control by traditional method. On more conventional designs, formal aspect of the methodology could avoid misunderstanding between hardware and ALLEGRO layout designers, minimizing prototype iteration, development time and price. The capability to keep trace of the original digital designer intents in schematic or board layout, loading formal constraints in EDMS, could also be considered for LHC electro...

  19. Study of the layout plan in the tokamak complex building for ITER

    International Nuclear Information System (INIS)

    Sato, Kazuyoshi; Yagenji, Akira; Sekiya, Shigeki; Takahashi, Hideo; Tamura, Kousaku; Neyatani, Yuzuru; Hashimoto, Masayoshi; Ogino, Shunji; Nagamatsu, Nobuhide; Motohashi, Keiichi; Uehara, Masaharu; Kataoka, Takahiro; Ohashi, Hironori

    2006-03-01

    This report summarizes study of the layout plan in the ITER Tokamak complex building as an invite to set up its plant in Japan. To draw up this arrangement plan, final design report (FDR), which was designed for main components and determined for the non-site specific design, was reconstructed systematically for the Japanese site. A supplementary design was performed for the insufficiency parts of FDR. An additional study was also performed for the adaptation of a regulatory framework including technical safety requirements in Japan. We proposed the tokamak complex building with seismic isolation to combine with the hot cell building. Through the studies, a layout plan has been constructed including maintenance plan for personnel access and component route with in the building from assembly to operation period. This layout plan would be used as a basis in the construction period, although final decision will be done by ITER organization. (author)

  20. How high is visual short-term memory capacity for object layout?

    Science.gov (United States)

    Sanocki, Thomas; Sellers, Eric; Mittelstadt, Jeff; Sulman, Noah

    2010-05-01

    Previous research measuring visual short-term memory (VSTM) suggests that the capacity for representing the layout of objects is fairly high. In four experiments, we further explored the capacity of VSTM for layout of objects, using the change detection method. In Experiment 1, participants retained most of the elements in displays of 4 to 8 elements. In Experiments 2 and 3, with up to 20 elements, participants retained many of them, reaching a capacity of 13.4 stimulus elements. In Experiment 4, participants retained much of a complex naturalistic scene. In most cases, increasing display size caused only modest reductions in performance, consistent with the idea of configural, variable-resolution grouping. The results indicate that participants can retain a substantial amount of scene layout information (objects and locations) in short-term memory. We propose that this is a case of remote visual understanding, where observers' ability to integrate information from a scene is paramount.

  1. Diagram Size vs. Layout Flaws: Understanding Quality Factors of UML Diagrams

    DEFF Research Database (Denmark)

    Störrle, Harald

    2016-01-01

    , though, is our third goal of extending our analysis aspects of diagram quality. Method: We improve our definition of diagram size and add a (provisional) definition of diagram quality as the number of topographic layout flaws. We apply these metrics on 60 diagrams of the five most commonly used types...... of UML diagram. We carefully analyze the structure of our diagram samples to ensure representativeness. We correlate diagram size and layout quality with modeler performance data obtained in previous experiments. The data set is the largest of its kind (n-156). Results: We replicate earlier findings......, and extend them to two new diagram types. We provide an improved definition of diagram size, and provide a definition of topographic layout quality, which is one more step towards a comprehensive definition of diagram quality as such. Both metrics are shown to be objectively applicable. We quantify...

  2. LAYOUT CELULAR: PROPOSTA E IMPLANTAÇÃO EM EMPRESA START-UP DE TECNOLOGIA

    Directory of Open Access Journals (Sweden)

    Lucas Almeida Dos Santos

    2016-12-01

    Full Text Available A escolha correta de um layout proporciona à organização se adaptar para melhor utilizar seus recursos em busca da melhoria contínua. A presente pesquisa, apresenta a elaboração e implantação de um layout celular tendo por base o uso das ferramentas de processos, Fluxograma, 5W2H e Diagrama de causa e efeito, no apoio da tomada de decisão do melhor layout a ser implantado.  Diante do exposto, o escopo da pesquisa objetiva apresentar a implantação do layout celular em uma empresa start-up de tecnologia, bem como os resultados obtidos mediante a proposta apresentada. Como metodologia de pesquisa, definiu-se o presente estudo como um estudo de caso, onde foi possível realizar a análise da estrutura física que corresponde a 60 m² de área de produção, para implementar o layout celular. Como principal resultado obtido destaca-se o sucesso da implantação, onde, o mesmo atendeu todas as necessidades de fabricação do produto na organização pesquisada. Concomitantemente a evolução do layout, foram definidos quatro postos de trabalho, onde se tem a entrada de MP (matéria-prima em A e a saída do produto acabado em D, conforme exposto nos resultados.

  3. City rats: insight from rat spatial behavior into human cognition in urban environments.

    Science.gov (United States)

    Yaski, Osnat; Portugali, Juval; Eilam, David

    2011-09-01

    The structure and shape of the urban environment influence our ability to find our way about in the city. Understanding how the physical properties of the environment affect spatial behavior and cognition is therefore a necessity. However, there are inherent difficulties in empirically studying complex and large-scale urban environments. These include the need to isolate the impact of specific urban features and to acquire data on the physical activity of individuals. In the present study, we attempted to overcome the above obstacles and examine the relation between urban environments and spatial cognition by testing the spatial behavior of rats. This idea originated from the resemblance in the operative brain functions and in the mechanisms and strategies employed by humans and other animals when acquiring spatial information and establishing an internal representation, as revealed in past studies. Accordingly, we tested rats in arenas that simulated a grid urban layout (e.g. Manhattan streets) and an irregular urban layout (e.g. Jerusalem streets). We found that in the grid layout, rat movement was more structured and extended over a greater area compared with their restricted movement in the irregular layout. These movement patterns recall those of humans in respective urban environments, illustrating that the structure and shape of the environment affect spatial behavior similarly in humans and rats. Overall, testing rats in environments that simulate facets of urban environments can provide new insights into human spatial cognition in urban environments.

  4. ALTERAÇÃO DE UM LAYOUT FUNCIONAL PARA LAYOUT CELULAR MOTIVADO PELOS FUNDAMENTOS DA MANUFATURA ENXUTA: ESTUDO DE CASO EM UMA INDÚSTRIA DE TRANSFORMADORES

    Directory of Open Access Journals (Sweden)

    Felipe Crisóstomo Gadelha

    2015-12-01

    Full Text Available O presente trabalho apresenta o estudo de uma alteração de layout, de funcional para celular, motivado pelos fundamentos da manufatura enxuta. Tendo como objetivo verificar os benefícios de se utilizar a manufatura celular com fluxo enxuto (contínuo, apresenta como metodologia um estudo de caso, pós-fato, em uma indústria de transformadores, onde a mudança foi realizada. Para fundamentar o estudo, apresenta revisão dos temas: Sistema de Manufatura Enxuta e layout industrial, para, em seguida, trazer os dados apresentados por esta indústria, ainda em um arranjo físico funcional, antes da alteração, e, em seguida, nas células de manufatura com um fluxo enxuto, após a alteração, e realizar uma comparação entre ambos. Os resultados obtidos desta comparação apresentam ganhos como aumento de produção, em 20%, e produtividade, em 56%, redução de lead time, em 67%, mão de obra direta, em 30%, tempo de processamento, em 20%, e área fabril, em 24%, dentre outros, evidenciando os benefícios que a utilização de um layout celular e Manufatura Enxuta proporcionam.

  5. Layout Determining Features, their Influence Zones and Respect Distances at the Olkiluoto Site

    International Nuclear Information System (INIS)

    Pere, T.; Ahokas, H.; Vaittinen, T.; Wikstroem, L.

    2012-12-01

    Fault zones located at the site of an underground nuclear waste repository may pose a risk to the repository by acting as potential hosts for earthquakes during the present day or future stress fields and having the possibility to induce secondary displacements on nearby large fractures, which may damage the nuclear waste canisters, if being intersected by such fractures. The fault zones may additionally provide possible flow routes, important for the transport of radionuclides and the chemical stability of the repository. It is therefore important to identify such structures, defined as layout determining features (LDF), and to assess their influence on the surrounding host rock and to determine respect volumes to the structures, which are avoided in the layout planning in order to mitigate the possible harmful effects to the repository. Fault zones with a trace length of 3 km or more are considered as layout determining features as these can potentially host an earthquake of a magnitude of 5.5 or more and may thus induce secondary displacements larger than 5 cm on nearby fractures, which is held as the current canister damage threshold premise. Fault zones with a size less than 3 km are considered unlikely candidates to induce secondary displacements of 5 cm or larger. In addition to the earthquake potential, hydrogeological zones with high T -value (geometrical mean T ≤ 10 -6 m 2 /s) and large dimensions (at least several hundred metres) are also defined as layout determining features. For each layout determining feature an influence zone is defined, depicting a volume around a fault zone or a hydrogeological zone with increased fracture density and permeability, often also called as damage zones in the scientific literature. Influence zones are therefore considered as mechanically weak and/or transmissive parts of the host rock, which may cause harmful effects to the performance of the repository if intersecting deposition tunnels or deposition holes. In

  6. Layout of NALM fiber laser with adjustable peak power of generated pulses.

    Science.gov (United States)

    Smirnov, Sergey; Kobtsev, Sergey; Ivanenko, Alexey; Kokhanovskiy, Alexey; Kemmer, Anna; Gervaziev, Mikhail

    2017-05-01

    The Letter proposes a new layout of a passively mode-locked fiber laser based on a nonlinear amplifying loop mirror (NALM) with two stretches of active fiber and two independently controlled pump modules. In contrast with conventional NALM configurations using a single piece of active fiber that yields virtually constant peak power, the proposed novel laser features larger than a factor of 2 adjustment range of peak power of generated pulses. The proposed layout also provides independent adjustment of duration and peak power of generated pulses as well as power-independent control of generated pulse spectral width impossible in NALM lasers with a single piece of active fiber.

  7. Optimization of lens layout for THz signal free-space delivery

    Science.gov (United States)

    Yu, Jimmy; Zhou, Wen

    2018-03-01

    We investigate how to extend the air-space distance for Terahertz (THz) signal by using optimized lens layout. After a delivery over 129.6 cm air-space we realize the BER of 10 Gb/s QPSK signal at 450 GHz smaller than 1 ×10-4 with this optimized lens layout. If only two lenses are employed, the BER is higher than forward error correction (FEC) threshold at the input power of 15 dBm into the photodiode.

  8. Effect of Asymmetric Layout of IGBT Modules on Reliability of Power Inverters in Motor Drive System

    DEFF Research Database (Denmark)

    Choi, Uimin; Vernica, Ionut; Blaabjerg, Frede

    2018-01-01

    An IGBT module has typically multiple power devices for some technical and cost advantages. This kind of configurations could have an asymmetric layout, which may lead to different thermal loadings and thereby lifetime difference of the power devices. Therefore, both the power rating and lifetime...... of inverters are limited by the most stressed devices. However, generally common data is provided for all devices and this may cause improper design of the inverters in terms of power rating and lifetime. In this paper, the effect of an asymmetric layout of IGBT modules on the reliability of power inverters...

  9. Note: Optimization of magnifying a polarization angle with Littrow layout blazed gratings.

    Science.gov (United States)

    Sasao, H; Arakawa, H; Imazawa, R; Kawano, Y; Itami, K; Kubo, H

    2017-03-01

    Magnification of a polarization angle with Littrow layout gratings has been developed. High magnification with a factor of 7.7 using two gratings in Littrow layout was experimentally proved. The magnification range was investigated by calculation at a wavelength of 10.6 μm. The method can be applied for a high magnification factor >30. Larger groove numbers and smaller blaze angles are suitable for the large magnification. Statistical fluctuation of the diffracted polarization angle is compared with that of the incident polarization angle.

  10. Multi-Criteria Layout Synthesis of MEMS Devices Using Memetic Computing

    DEFF Research Database (Denmark)

    Tutum, Cem Celal; Fan, Zhun

    2011-01-01

    This paper introduces a multi-objective optimization approach for layout synthesis of MEMS components. A case study of layout synthesis of a comb-driven micro-resonator shows that the approach proposed in this paper can lead to design results accommodating two design objectives, i.e. simultaneous...... sorting genetic algorithm (NSGA-II), has been applied to find multiple trade-off solutions followed by a gradient-based local search, i.e. sequential quadratic programming (SQP), to improve the convergence of the obtained Pareto-optimal front. In order to reduce the number of function evaluations...

  11. Operator Station Design System - A computer aided design approach to work station layout

    Science.gov (United States)

    Lewis, J. L.

    1979-01-01

    The Operator Station Design System is resident in NASA's Johnson Space Center Spacecraft Design Division Performance Laboratory. It includes stand-alone minicomputer hardware and Panel Layout Automated Interactive Design and Crew Station Assessment of Reach software. The data base consists of the Shuttle Transportation System Orbiter Crew Compartment (in part), the Orbiter payload bay and remote manipulator (in part), and various anthropometric populations. The system is utilized to provide panel layouts, assess reach and vision, determine interference and fit problems early in the design phase, study design applications as a function of anthropometric and mission requirements, and to accomplish conceptual design to support advanced study efforts.

  12. Analysis of Location Ambiguity, GDOP and Station Layout of Threestation in Multilateration

    Directory of Open Access Journals (Sweden)

    Xu Zi Li

    2016-01-01

    Full Text Available In practice, the two-dimensional TDOA source location in the case of three stations would encounter the ambiguity problem of dual solutions. The relationship between distributions of location curve intersections, GDOP and receiving station layout is numerically analyzed, namely the distributions of location curve intersections and GDOP are determined by the receiving station layout, and the areas of two curve intersections are consistent with these of larger GDOP. These analysis results could serve as reference for avoiding or dealing with the ambiguity problem when multilateration is in application.

  13. Study of the computer-aided implantation and layout of printed circuits

    International Nuclear Information System (INIS)

    Baudry, Marc

    1973-01-01

    This research thesis reports the design and implementation of a software aimed at a computer-aided implantation and layout of printed circuits. This work comprises the use of heuristic algorithms and the search for a minimum cost by reduction of computing time and of memory size. The software comprises four independent parts which respectively address data analysis and control, circuit implantation, connection layout, and the exploitation of the obtained results. These four parts and their subroutines are presented. Two examples are reported in appendix

  14. Tabu search approaches for the multi-level warehouse layout problem with adjacency constraints

    Science.gov (United States)

    Zhang, G. Q.; Lai, K. K.

    2010-08-01

    A new multi-level warehouse layout problem, the multi-level warehouse layout problem with adjacency constraints (MLWLPAC), is investigated. The same item type is required to be located in adjacent cells, and horizontal and vertical unit travel costs are product dependent. An integer programming model is proposed to formulate the problem, which is NP hard. Along with a cube-per-order index policy based heuristic, the standard tabu search (TS), greedy TS, and dynamic neighbourhood based TS are presented to solve the problem. The computational results show that the proposed approaches can reduce the transportation cost significantly.

  15. The study on the Layout of the Charging Station in Chengdu

    Science.gov (United States)

    Cai, yun; Zhang, wanquan; You, wei; Mao, pan

    2018-03-01

    In this paper, the comprehensive analysis of the factors affecting the layout of the electric car, considering the principle of layout of the charging station. Using queuing theory in operational research to establish mathematical model and basing on the principle of saving resource and convenient owner to optimize site number. Combining the theory of center to determine the service radius, Using the Gravity method to determine the initial location, Finally using the method of center of gravity to locate the charging station’s location.

  16. On the Impact of Layout Quality to Understanding UML Diagrams: Diagram Type and Expertise

    DEFF Research Database (Denmark)

    Störrle, Harald

    2012-01-01

    Practical experience suggests that the use and understanding of UML diagrams is greatly affected by the quality of their layout. In previous work, we have presented evidence supporting this intuition. This contrasts with earlier experiments that yielded weak or inconclusive evidence only. In the ......Practical experience suggests that the use and understanding of UML diagrams is greatly affected by the quality of their layout. In previous work, we have presented evidence supporting this intuition. This contrasts with earlier experiments that yielded weak or inconclusive evidence only...

  17. tkLayout: a design tool for innovative silicon tracking detectors

    Science.gov (United States)

    Bianchi, G.

    2014-03-01

    A new CMS tracker is scheduled to become operational for the LHC Phase 2 upgrade in the early 2020's. tkLayout is a software package developed to create 3d models for the design of the CMS tracker and to evaluate its fundamental performance figures. The new tracker will have to cope with much higher luminosity conditions, resulting in increased track density, harsher radiation exposure and, especially, much higher data acquisition bandwidth, such that equipping the tracker with triggering capabilities is envisaged. The design of an innovative detector involves deciding on an architecture offering the best trade-off among many figures of merit, such as tracking resolution, power dissipation, bandwidth, cost and so on. Quantitatively evaluating these figures of merit as early as possible in the design phase is of capital importance and it is best done with the aid of software models. tkLayout is a flexible modeling tool: new performance estimates and support for different detector geometries can be quickly added, thanks to its modular structure. Besides, the software executes very quickly (about two minutes), so that many possible architectural variations can be rapidly modeled and compared, to help in the choice of a viable detector layout and then to optimize it. A tracker geometry is generated from simple configuration files, defining the module types, layout and materials. Support structures are automatically added and services routed to provide a realistic tracker description. The tracker geometries thus generated can be exported to the standard CMS simulation framework (CMSSW) for full Monte Carlo studies. tkLayout has proven essential in giving guidance to CMS in studying different detector layouts and exploring the feasibility of innovative solutions for tracking detectors, in terms of design, performance and projected costs. This tool has been one of the keys to making important design decisions for over five years now and has also enabled project engineers

  18. Engineering Complex Tissues

    Science.gov (United States)

    MIKOS, ANTONIOS G.; HERRING, SUSAN W.; OCHAREON, PANNEE; ELISSEEFF, JENNIFER; LU, HELEN H.; KANDEL, RITA; SCHOEN, FREDERICK J.; TONER, MEHMET; MOONEY, DAVID; ATALA, ANTHONY; VAN DYKE, MARK E.; KAPLAN, DAVID; VUNJAK-NOVAKOVIC, GORDANA

    2010-01-01

    This article summarizes the views expressed at the third session of the workshop “Tissue Engineering—The Next Generation,” which was devoted to the engineering of complex tissue structures. Antonios Mikos described the engineering of complex oral and craniofacial tissues as a “guided interplay” between biomaterial scaffolds, growth factors, and local cell populations toward the restoration of the original architecture and function of complex tissues. Susan Herring, reviewing osteogenesis and vasculogenesis, explained that the vascular arrangement precedes and dictates the architecture of the new bone, and proposed that engineering of osseous tissues might benefit from preconstruction of an appropriate vasculature. Jennifer Elisseeff explored the formation of complex tissue structures based on the example of stratified cartilage engineered using stem cells and hydrogels. Helen Lu discussed engineering of tissue interfaces, a problem critical for biological fixation of tendons and ligaments, and the development of a new generation of fixation devices. Rita Kandel discussed the challenges related to the re-creation of the cartilage-bone interface, in the context of tissue engineered joint repair. Frederick Schoen emphasized, in the context of heart valve engineering, the need for including the requirements derived from “adult biology” of tissue remodeling and establishing reliable early predictors of success or failure of tissue engineered implants. Mehmet Toner presented a review of biopreservation techniques and stressed that a new breakthrough in this field may be necessary to meet all the needs of tissue engineering. David Mooney described systems providing temporal and spatial regulation of growth factor availability, which may find utility in virtually all tissue engineering and regeneration applications, including directed in vitro and in vivo vascularization of tissues. Anthony Atala offered a clinician’s perspective for functional tissue

  19. On the Impact of Diagram Layout: How Are Models Actually Read?

    DEFF Research Database (Denmark)

    Störrle, Harald; Baltsen, Nick; Christoffersen, Henrik

    2014-01-01

    This poster presents the latest results from a very large eye tracking study (n=29) that explores how modelers read UML diagrams. We find that various factors like layout quality, modeler experience, and diagram type lead to significant differences in diagram reading strategies. We derive elements...

  20. On the use of layout, colour and typography on visual display terminals

    NARCIS (Netherlands)

    Nes, van F.L.

    1985-01-01

    Some guidelines are given to meet the observed need for rules about the use of colour and typography on multicolour display screens so as to create texts of optimum legibility. Examples of videotex pages are used to illustrate right and wrong layouts, applications of colour and letter type. The

  1. 77 FR 55896 - Notice of Release Effecting Federal Grant Assurance Obligations Due to Airport Layout Plan...

    Science.gov (United States)

    2012-09-11

    ... Grant Assurance Obligations Due to Airport Layout Plan Revision at Mather Airport, Sacramento, CA AGENCY... Airport Boulevard, Sacramento, CA 95837. SUPPLEMENTARY INFORMATION: In accordance with the Wendell H. Ford... Mather Airport, Sacramento, California, which will provide for a release from the Grant Agreement...

  2. Efficacy of paediatric anaesthetic trolleys: A call for a basic standard and layout.

    Science.gov (United States)

    Griffiths, Sian E; Boleat, Elizabeth; Goodwin, Alison; Sheikh, Asme; Goonasekera, Chulananda

    2015-01-01

    Providing safe anaesthesia to children especially in emergency situations goes hand in hand with instant availability of appropriately sized equipment and monitoring. This is best achieved using a designated paediatric anaesthetic trolley containing essential equipment. Guidance for the contents of such trolleys is neither explicit nor standard. We used a survey and a qualitative enquiry to develop a checklist suitable for standardisation of contents and layout of paediatric anaesthetic trolleys. We conducted an observational study of our current practice and paediatric anaesthetic trolleys in a tertiary care hospital. We also performed a qualitative enquiry from experienced paediatric anaesthetists and operating department practitioners.We developed an empirical checklist to ensure the minimum 'essential' equipment is available on these trolleys and implemented a standard layout to facilitate its use. We identified 11 areas in our hospital where anaesthesia is provided to children, each with a designated paediatric anaesthetic trolley. There were considerable deficiencies of items in all areas with no standard pattern or layout. Different types of trolleys contributed to the confusion. In addition, overstocking of inappropriate items hindered its efficient use. Standardising the contents and layout of the paediatric anaesthetic trolley is an essential pre-requisite for safer paediatric anaesthetic practice.

  3. Development and layout of a protocol for the field performance of concrete deck and crack sealers.

    Science.gov (United States)

    2009-09-01

    The main objective of this project was to develop and layout a protocol for the long-term monitoring and assessment of the performance of concrete deck and crack sealants in the field. To accomplish this goal, a total of six bridge decks were chosen ...

  4. Wind farm layout optimization in complex terrain: A preliminary study on a Gaussian hill

    International Nuclear Information System (INIS)

    Feng, J; Shen, W Z

    2014-01-01

    One of the crucial problems for wind farm (WF) development is wind farm layout optimization. It seeks to find the optimal positions of wind turbines (WTs) inside a WF, so as to maximize and/or minimize a single objective or multiple objectives, while satisfying certain constraints. Although this problem for WFs in flat terrain or offshore has been investigated in many studies, it is still a challenging problem for WFs in complex terrain. In this preliminary study, the wind flow conditions of complex terrain without WTs are first obtained from computational fluid dynamics (CFD) simulation, then an adapted Jensen wake model is developed by considering the terrain features and taking the inflow conditions as input. Using this combined method, the wake effects of WF in complex terrain are properly modelled. Besides, a random search (RS) algorithm proposed in previous study is improved by adding some adaptive mechanisms and applied to solve the layout optimization problem of a WF on a Gaussian shape hill. The layout of the WF with a certain number of WTs is optimized to maximize the total power output, which obtained steady improvements over expert guess layouts

  5. Cycle layout studies of S-CO2 cycle for the next generation nuclear system application

    International Nuclear Information System (INIS)

    Ahn, Yoonhan; Bae, Seong Jun; Kim, Minseok; Cho, Seong Kuk; Baik, Seungjoon; Lee, Jeong Ik; Cha, Jae Eun

    2014-01-01

    According to the second law of thermodynamics, the next generation nuclear reactor system efficiency can potentially be increased with higher operating temperature. Fig.1 shows several power conversion system efficiencies and heat sources with respect to the system top operating temperature. As shown in Fig.1, the steam Rankine and gas Brayton cycles have been considered as the major power conversion systems more than several decades. In the next generation reactor operating temperature region (450 - 900 .deg. C), the steam Rankine and gas Brayton cycles have limits due to material problems and low efficiency, respectively. Among the future power conversion systems, S-CO 2 cycle is receiving interests due to several benefits including high efficiency under the mild turbine inlet temperature range (450-650 .deg. C), compact turbomachinery and simple layout compared to the steam Rankine cycle. S-CO 2 cycle can show relatively high efficiency under the mild turbine inlet temperature range (450-600 .deg. C) compared to other power conversion systems. The recompression cycle shows the best efficiency among other layouts and it is suitable for the application to advanced nuclear reactor systems. As S-CO 2 cycle performance can vary depending on the layout configuration, further studies on the layouts are required to design a better performing cycle

  6. BFL: a node and edge betweenness based fast layout algorithm for large scale networks

    Science.gov (United States)

    Hashimoto, Tatsunori B; Nagasaki, Masao; Kojima, Kaname; Miyano, Satoru

    2009-01-01

    Background Network visualization would serve as a useful first step for analysis. However, current graph layout algorithms for biological pathways are insensitive to biologically important information, e.g. subcellular localization, biological node and graph attributes, or/and not available for large scale networks, e.g. more than 10000 elements. Results To overcome these problems, we propose the use of a biologically important graph metric, betweenness, a measure of network flow. This metric is highly correlated with many biological phenomena such as lethality and clusters. We devise a new fast parallel algorithm calculating betweenness to minimize the preprocessing cost. Using this metric, we also invent a node and edge betweenness based fast layout algorithm (BFL). BFL places the high-betweenness nodes to optimal positions and allows the low-betweenness nodes to reach suboptimal positions. Furthermore, BFL reduces the runtime by combining a sequential insertion algorim with betweenness. For a graph with n nodes, this approach reduces the expected runtime of the algorithm to O(n2) when considering edge crossings, and to O(n log n) when considering only density and edge lengths. Conclusion Our BFL algorithm is compared against fast graph layout algorithms and approaches requiring intensive optimizations. For gene networks, we show that our algorithm is faster than all layout algorithms tested while providing readability on par with intensive optimization algorithms. We achieve a 1.4 second runtime for a graph with 4000 nodes and 12000 edges on a standard desktop computer. PMID:19146673

  7. Scopes describe frames : A uniform model for memory layout in dynamic semantics

    NARCIS (Netherlands)

    Poulsen, C.B.; Neron, P.J.M.; Tolmach, Andrew; Visser, Eelco; Krishnamurthi, Shriram; Lerner, Benjamin S.

    2016-01-01

    Semantic specifications do not make a systematic connection between the names and scopes in the static structure of a program and memory layout, and access during its execution. In this paper we introduce a systematic approach to the alignment of names in static semantics and memory in dynamic

  8. Optimal Stack Layout in a Sea Container Terminal with Automated Lifting Vehicles

    NARCIS (Netherlands)

    D. Roy (Debjit); A. Gupta (Akash); S. Parhi (Sampanna); M.B.M. de Koster (René)

    2014-01-01

    textabstractContainer terminal performance is largely determined by its design decisions, which include the number and type of quay cranes (QCs), stack cranes (SCs), transport vehicles, vehicle travel path, and stack layout. The terminal design process is complex because it is affected by factors

  9. Spatio-Temporal Layout of Human Actions for Improved Bag-of-Words Action Detection

    NARCIS (Netherlands)

    Burghouts, G.J.; Schutte, K.

    2013-01-01

    We investigate how human action recognition can be improved by considering spatio-temporal layout of actions. From literature, we adopt a pipeline consisting of STIP features, a random forest to quantize the features into histograms, and an SVM classifier. Our goal is to detect 48 human actions,

  10. A Multi-Objective Optimization Framework for Offshore Wind Farm Layouts and Electric Infrastructures

    Directory of Open Access Journals (Sweden)

    Silvio Rodrigues

    2016-03-01

    Full Text Available Current offshore wind farms (OWFs design processes are based on a sequential approach which does not guarantee system optimality because it oversimplifies the problem by discarding important interdependencies between design aspects. This article presents a framework to integrate, automate and optimize the design of OWF layouts and the respective electrical infrastructures. The proposed framework optimizes simultaneously different goals (e.g., annual energy delivered and investment cost which leads to efficient trade-offs during the design phase, e.g., reduction of wake losses vs collection system length. Furthermore, the proposed framework is independent of economic assumptions, meaning that no a priori values such as the interest rate or energy price, are needed. The proposed framework was applied to the Dutch Borssele areas I and II. A wide range of OWF layouts were obtained through the optimization framework. OWFs with similar energy production and investment cost as layouts designed with standard sequential strategies were obtained through the framework, meaning that the proposed framework has the capability to create different OWF layouts that would have been missed by the designers. In conclusion, the proposed multi-objective optimization framework represents a mind shift in design tools for OWFs which allows cost savings in the design and operation phases.

  11. The lay-out of the photon collider at the international linear collider

    Indian Academy of Sciences (India)

    6. — journal of. December 2007 physics pp. 1177–1179. The lay-out of the photon collider ... the sum of the disruption angle and the angular size of the final quad. ... will be less precise and it can affect the quality of some physics results.

  12. Interaction Between Shelf Layout and Marketing Effectiveness and Its Impact on Optimizing Shelf Arrangements

    NARCIS (Netherlands)

    van Nierop, Erjen; Fok, Dennis; Franses, Philip Hans

    2008-01-01

    In this paper, we propose and operationalize a new method for optimizing shelf arrangements. We show that there are important dependencies between the layout of the shelf and stock-keeping unit (SKU) sales and marketing effectiveness. The importance of these dependencies is further shown by the

  13. Optimization of Wind Farm Layout: A Refinement Method by Random Search

    DEFF Research Database (Denmark)

    Feng, Ju; Shen, Wen Zhong

    2013-01-01

    Wind farm layout optimization is to find the optimal positions of wind turbines inside a wind farm, so as to maximize and/or minimize a single objective or multiple objectives, while satisfying certain constraints. Most of the works in the literature divide the wind farm into cells in which turbi...

  14. Multi-objective random search algorithm for simultaneously optimizing wind farm layout and number of turbines

    DEFF Research Database (Denmark)

    Feng, Ju; Shen, Wen Zhong; Xu, Chang

    2016-01-01

    A new algorithm for multi-objective wind farm layout optimization is presented. It formulates the wind turbine locations as continuous variables and is capable of optimizing the number of turbines and their locations in the wind farm simultaneously. Two objectives are considered. One is to maximi...

  15. Modelling Wind for Wind Farm Layout Optimization Using Joint Distribution of Wind Speed and Wind Direction

    DEFF Research Database (Denmark)

    Feng, Ju; Shen, Wen Zhong

    2015-01-01

    Reliable wind modelling is of crucial importance for wind farm development. The common practice of using sector-wise Weibull distributions has been found inappropriate for wind farm layout optimization. In this study, we propose a simple and easily implementable method to construct joint distribu...

  16. Visualization of the Evolution of Layout Metrics for Business Process Models

    DEFF Research Database (Denmark)

    Haisjackl, Cornelia; Burattin, Andrea; Soffer, Pnina

    2017-01-01

    Considerable progress regarding impact factors of process model understandability has been achieved. For example, it has been shown that layout features of process models have an effect on model understandability. Even so, it appears that our knowledge about the modeler’s behavior regarding the l...

  17. Mathematical models for the definition of cell manufacturing layout. Literature review

    Directory of Open Access Journals (Sweden)

    Gustavo Andrés Romero Duque

    2015-11-01

    Full Text Available This review article discusses the approach to the layout problem of cell manufacturing (LCM in a descriptive form; considering at first the problem and its variations, then the elements of the mathematical models, subsequently presenting solution methods used; and finally some future perspectives about this topic are considered.

  18. Effect of Changes in Layout Shape on Unit Construction Cost of ...

    African Journals Online (AJOL)

    The conclusions of previous studies on the cost implication of building shape have been premised on the knowledge of building morphological and geometrical characteristics, and have lacked empirical authentication. This study used empirical data to investigate the effect of layout narrowness and complexity (irregularity) ...

  19. A layout technique for class diagrams to be used in product configuration projects

    DEFF Research Database (Denmark)

    Haug, Anders; Hvam, Lars; Mortensen, Niels Henrik

    2010-01-01

    . On the other hand, the requirements for the design language are more focused on having a formalised and rich language. For this task class diagrams are often applied. To avoid the use of different modelling languages in the analysis and design phase, this paper proposes and tests a layout technique...

  20. Topological material layout in plates for vibration suppression and wave propagation control

    DEFF Research Database (Denmark)

    Larsen, Anders Astrup; Laksafoss, B.; Jensen, Jakob Søndergaard

    2009-01-01

    We propose a topological material layout method to design elastic plates with optimized properties for vibration suppression and guided transport of vibration energy. The gradient-based optimization algorithm is based on a finite element model of the plate vibrations obtained using the Mindlin...