Diagnóstico del uso de animales de tiro en una zona montañosa del norte del Cauca

Directory of Open Access Journals (Sweden)

Herrera Gutiérrez Oscar Alonso

1995-12-01

Full Text Available

The possibilities to stablish an organization of plowmen were studied in the northern zone of the Department del Cauca (Colombia in 1993. This research was carried out in four representative subzones, San Antonio, Mondomo, El Pital and Pescador. The factors included in the study were: the regional pattern of mechanization (PMR, draught offer, economical analysis and animal management. At the same time, a survey between the plowmen supplied information about feeding, health, criteria for the selection of draught animals, machines and implements, monthly income and regional pattern of mechanization (PMR. As a result, the Regional Organization of Plowmen of the Northern Cauca was created. The draught offer in the zone (number of oxen and plowmen was concentrated (more than 80% in the subzones of Pescador and Mondomo. San Antonio and El Pital were the most profitable subzones, The survey revealed a necessity for the education of plowmen and a supplementary action to diet and sanitary care of the oxen because it is difficult to define a feeding rule with reference to the energy requirements.

En 1993, en la Zona norte del Departamento del Cauca, Colombia, se llevó a cabo un estudio que se ocupó de establecer las posibilidades de organización de los yunteros locales; de realizar, en cuatro subzonas representativas de la región -San Antonio, Mondomo, El Piral y Pescador-, estudios de caso respecto al Patrón de Mecanización Regional (PMR, oferta de tiro, análisis económico y manejo de los animales; igualmente, a través de 40 encuestas entre yunteros de la zona se indagó acerca de la alimentación, enfermedades y criterios de selección de los animales de tiro; y de los tipos de máquinas y de aperos utilizados, ingresos mensuales y Patrón de Mecanización Regional (PMR. Como resultado de varios encuentros regionales de yunteros se constituyó la ORGANIZACION REGIONAL DE BUEYEROS DEL NORTE DEL CAUCA. La oferta de tiro (número de

¿Es el plomo empleado en deportes (caza, tiro y pesca deportiva un problema de salud pública infravalorado?

Directory of Open Access Journals (Sweden)

Raimon Guitart

2005-01-01

Full Text Available La munición y los pesos empleados en actividades recreativas como la caza, el tiro y la pesca deportiva han sido fabricados tradicionalmente con plomo. En España la caza y el tiro son responsables de la dispersión en la naturaleza de cerca de 6.000 toneladas anuales del metal pesado, mientras que podemos estimar en 100 las aportadas por pescadores deportivos a las zonas acuáticas. Las pocas medidas legales que varios países han adoptado en contra del uso del plomo en esos deportes se han basado en las pruebas irrefutables que indicaban que cada año fallecían intoxicadas millones de aves, que ingerían inadvertidamente esos pequeños objetos de plomo hallados abandonados en sus hábitats naturales. En este trabajo se discute si el enfoque conservacionista que se ha dado hasta ahora al problema resulta adecuado, y si las evidencias de los daños sobre los seres humanos son o no suficientes para extender todavía más esas medidas de prohibición, en especial teniendo en cuenta que en niños se considera que no hay dosis de exposición segura. Se concluye que en algunos aspectos los datos ya existen, aunque en otros los estudios tóxico-epidemiológicos son todavía escasos, sugiriendo que al tema se le ha prestado poca atención. En cualquier caso, resulta preocupante constatar que el principio de precaución no se ha aplicado para solucionar un problema cuyos efectos sanitarios serán más a largo plazo que inmediatos.

National Plan for Stratospheric Ozone Monitoring and Early Detection of Change, 1981-1986

International Nuclear Information System (INIS)

1982-02-01

A transition from reliance on a ground-based, geographically-biased ozone observing network operated by cooperating nations to a combined satellite and ground-based monitoring program that will provide global coverage of the vertical distribution of stratospheric ozone, as well as total ozone overburden is discussed. The strategy, instrumentation, and monitoring products to be prepared during this transition period are also discussed. Global atmospheric monitoring for protection of the ultraviolet shielding properties of atmospheric ozone is considered. The operational satellite ozone vertical profile monitoring system to be flown on the NOAA Tiros N operational satellite series to carry on ozone measurements initiated on the NASA R D satellites is also considered

SAFARI 2000 TOVS Surface and Atmospheric Parameters, 1-Deg, 1999-2001

Data.gov (United States)

National Aeronautics and Space Administration — ABSTRACT: NOAA's TIROS (Television Infrared Observation Satellite) Operational Vertical Sounder (TOVS) is a suite of three sensors: the Microwave Sounding Unit...

SAFARI 2000 TOVS Surface and Atmospheric Parameters, 1-Deg, 1999-2001

Data.gov (United States)

National Aeronautics and Space Administration — NOAA's TIROS (Television Infrared Observation Satellite) Operational Vertical Sounder (TOVS) is a suite of three sensors: the Microwave Sounding Unit (MSU), the High...

GLA MONTHLY GRIDS from NOAA-11 V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

GLA 5 DAY GRIDS from NOAA-9 V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

GLA DAILY GRIDS from NOAA-10 V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

GLA MONTHLY GRIDS from NOAA-9 V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

GLA 5 DAY GRIDS from NOAA-11 V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

GLA MONTHLY GRIDS from NOAA-10 V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

GLA DAILY GRIDS from NOAA-11 V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

GLA MONTHLY GRIDS from TIROSN V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

GLA DAILY GRIDS from NOAA-12 V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

GLA 5 DAY GRIDS from NOAA-10 V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

GLA DAILY GRIDS from NOAA-9 V001

Data.gov (United States)

National Aeronautics and Space Administration — This dataset contains the TIROS Operational Vertical Sounder (TOVS) level 3 geophysical parameters derived using the physical retrieval method of Susskind et al....

Current transport in graphene/AlGaN/GaN vertical heterostructures probed at nanoscale.

Science.gov (United States)

Fisichella, Gabriele; Greco, Giuseppe; Roccaforte, Fabrizio; Giannazzo, Filippo

2014-08-07

Vertical heterostructures combining two or more graphene (Gr) layers separated by ultra-thin insulating or semiconductor barriers represent very promising systems for next generation electronics devices, due to the combination of high speed operation with wide-range current modulation by a gate bias. They are based on the specific mechanisms of current transport between two-dimensional-electron-gases (2DEGs) in close proximity. In this context, vertical devices formed by Gr and semiconductor heterostructures hosting an "ordinary" 2DEG can be also very interesting. In this work, we investigated the vertical current transport in Gr/Al(0.25)Ga(0.75)N/GaN heterostructures, where Gr is separated from a high density 2DEG by a ∼ 24 nm thick AlGaN barrier layer. The current transport from Gr to the buried 2DEG was characterized at nanoscale using conductive atomic force microscopy (CAFM) and scanning capacitance microscopy (SCM). From these analyses, performed both on Gr/AlGaN/GaN and on AlGaN/GaN reference samples using AFM tips with different metal coatings, the Gr/AlGaN Schottky barrier height ΦB and its lateral uniformity were evaluated, as well as the variation of the carrier densities of graphene (ngr) and AlGaN/GaN 2DEG (ns) as a function of the applied bias. A low Schottky barrier (∼ 0.40 eV) with excellent spatial uniformity was found at the Gr/AlGaN interface, i.e., lower compared to the measured values for metal/AlGaN contacts, which range from ∼ 0.6 to ∼ 1.1 eV depending on the metal workfunction. The electrical behavior of the Gr/AlGaN contact has been explained by Gr interaction with AlGaN donor-like surface states located in close proximity, which are also responsible of high n-type Gr doping (∼ 1.3 × 10(13) cm(-2)). An effective modulation of ns by the Gr Schottky contact was demonstrated by capacitance analysis under reverse bias. From this basic understanding of transport properties in Gr/AlGaN/GaN heterostructures, novel vertical field effect

Detecting annual and seasonal variations of CO2, CO and N2O from a multi-year collocated satellite-radiosonde data-set using the new Rapid Radiance Reconstruction (3R-N) model

International Nuclear Information System (INIS)

Chedin, A.; Serrar, S.; Hollingsworth, A.; Armante, R.; Scott, N.A.

2003-01-01

The NOAA polar meteorological satellites have embarked the TIROS-N operational vertical sounder (TOVS) since 1979. Using radiosondes and NOAA-10 TOVS measurements which are collocated within a narrow space and time window, we have studied the differences between the TOVS measurements and simulated measurements from a new fast, Rapid Radiance Reconstruction Network (3R-N), non-linear radiative transfer model with up to date spectroscopy. Simulations use radiosonde temperature and humidity measurements as the prime input. The radiative transfer model also uses fixed greenhouse gas absorber amounts (CO 2 ,CO,N 2 O) and reasonable estimates of O 3 and of surface temperature. The 3R-N model is first presented and validated. Then, a study of the differences between the simulated and measured radiances shows annual trends and seasonal variations consistent with independent measurements of variations in CO 2 and other greenhouse gases atmospheric concentrations. The improved accuracy of 3R-N and a better handling of its deviations with respect to observations allow most of difficulties met in a previous study (J. Climate 15 (2002) 95) to be resolved

Pathfinder Climate Data

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NOAA/NASA Pathfinder climate data CD-ROM contains seven data sets: Advanced Very High Resolution Radiometer (AVHRR)Land and Ocean, TIROS Operational Vertical...

Kuidas töötab teie kooli tugisüsteem? / Maria Tiro, Siiri Klasberg, Maarika Kongi ... [jt.

Index Scriptorium Estoniae

2011-01-01

Küsimusele vastasid Jüri gümnaasiumi direktor Maria Tiro, Tapa gümnaasiumi sotsiaalpedagoog Siiri Klasberg, Rakvere gümnaasiumi psühholoog Maarika Kongi, Kuressaare gümnaasiumi sotsiaalpedagoog Maret Martinson, Salme põhikooli direktor Marika Pütsep

Club de tiro en Noain España

Directory of Open Access Journals (Sweden)

Guibert Tabar, Javier

1977-03-01

Full Text Available The site at Noain Airport (Navarre, has been a conditioning factor of the height of the building, as it cannot exceed the plane of 14.3% which, starting from the level O, and 150 m from the runway axis, limits transition space. The general facilities, cloakrooms, toilets, armoury, etc., are on the ground floor. The bars and restaurants, as well as the covered terrace and the living rooms occupy the rest of the building. These quarters overlook the shooting grounds. The structure is of reinforced concrete with 5 m modules and bracketed cantilevers. The roof is made with sandwich plates and it has rugged anchorage. The walls are of half-pole double hollow brick, chamber and partition wail, coated with Maplexine.Está situado junto al aeropuerto de Noain (Navarra, lo que ha condicionado la altura del edificio, ya que no se puede sobrepasar el plano de 14,3% que, partiendo de la cota O, a 150 m del eje de la pista, delimita el espacio de transición. En la planta baja se distribuyen las instalaciones generales, vestuarios, aseos, armería, etc. Los bares y restaurantes, así como la terraza cubierta y los salones de estar, ocupan el resto del edificio. Estas dependencias tienen vistas a la cancha de tiro. Su estructura es a base de hormigón armado, con módulos de 5 m y ménsulas acarteladas. La cubierta está construida con placas sandwich y lleva anclajes resistentes. Los cerramientos son de ladrillo hueco doble de media asta, cámara y tabique, revestidos con Maplexine.

Huvi õpilase vastu peaks olema suurem / Maria Tiro, Merilin Piipuu, Valdo Randpere, Liisa Pakosta ; küsitlenud Sigrid Kõiv

Index Scriptorium Estoniae

2008-01-01

Jüri Gümnaasiumi direktor Maria Tiro, Eesti Õpilasesinduste Liidu juht Merilin Piipuu, lapsevanem ja IBM Eesti juht Valdo Randpere ning lapsevanem ja Eesti Lastevanemate Liidu esindaja Liisa Pakosta arutlesid koolivägivalla üle tänapäeva koolis

Detecting annual and seasonal variations of CO{sub 2}, CO and N{sub 2}O from a multi-year collocated satellite-radiosonde data-set using the new Rapid Radiance Reconstruction (3R-N) model

Energy Technology Data Exchange (ETDEWEB)

Chedin, A.; Serrar, S.; Hollingsworth, A.; Armante, R.; Scott, N.A

2003-03-15

The NOAA polar meteorological satellites have embarked the TIROS-N operational vertical sounder (TOVS) since 1979. Using radiosondes and NOAA-10 TOVS measurements which are collocated within a narrow space and time window, we have studied the differences between the TOVS measurements and simulated measurements from a new fast, Rapid Radiance Reconstruction Network (3R-N), non-linear radiative transfer model with up to date spectroscopy. Simulations use radiosonde temperature and humidity measurements as the prime input. The radiative transfer model also uses fixed greenhouse gas absorber amounts (CO{sub 2},CO,N{sub 2}O) and reasonable estimates of O{sub 3} and of surface temperature. The 3R-N model is first presented and validated. Then, a study of the differences between the simulated and measured radiances shows annual trends and seasonal variations consistent with independent measurements of variations in CO{sub 2} and other greenhouse gases atmospheric concentrations. The improved accuracy of 3R-N and a better handling of its deviations with respect to observations allow most of difficulties met in a previous study (J. Climate 15 (2002) 95) to be resolved.

Completion of potential conflicts of interest through optimization of Rukoh reservoir operation in Pidie District, Aceh Province, Indonesia

Science.gov (United States)

Azmeri, Hadihardaja, Iwan K.; Shaskia, Nina; Admaja, Kamal Surya

2017-11-01

Rukoh Reservoir's construction was planned to be built in Krueng Rukoh Watershed with supplet ion from Krueng Tiro River. Rukoh Reservoir operating system as a multipurpose reservoir raised potential conflict of interest between raw water and irrigation water. In this study, the operating system of Rukoh Reservoirs was designed to supply raw water in Titeu Sub-District and replenish water shortage in Baro Irrigation Area which is not able to be served by the Keumala Weir. Reservoir operating system should be planned optimally so that utilization of water in accordance with service area demands. Reservoir operation method was analyzed by using optimization technique with nonlinear programming. Optimization of reservoir operation is intended to minimize potential conflicts of interest in the operation. Suppletion discharge from Krueng Tiro River amounted to 46.62%, which was calculated based on ratio of Baro and Tiro irrigation area. However, during dry seasons, water demands could not be fully met, so there was a shortage of water. By considering the rules to minimize potential conflicts of interest between raw water and irrigation water, it would require suppletion from Krueng Tiro amounted to 52.30%. The increment of suppletion volume could minimize conflicts of interest. It produced l00% reservoir reliability for raw water and irrigation demands. Rukoh reservoir could serve raw water demands of Titeu Sub-District and irrigation demands of Baro irrigation area which is covering an area of 6,047 hectars. Reservoir operation guidelines can specify reservoir water release to balance the demands and the target storage.

PERFIL DE RENDIMIENTO TÉCNICO DEL EQUIPO TETRACAMPEÓN DE LA LIGA SUPERIOR DE BALONCESTO DE COSTA RICA

Directory of Open Access Journals (Sweden)

Braulio Sánchez Ureña

2011-12-01

Full Text Available El propósito de este estudio fue analizar y contrastar el perfil de rendimiento técnico del equipo tetracampeón de la Liga Superior de Baloncesto de Costa Rica. Se registró 142 juegos a lo largo de las temporadas 2007, 2008 y 2009. Los indicadores de rendimiento escogido fueron: lanzamientos de dos y tres puntos (convertidos, fallados, porcentaje de efectividad, lanzamientos de tiro libre (convertidos, fallados, porcentaje de efectividad, puntos, rebotes defensivos y ofensivos, faltas, pérdidas de balón, asistencias y robos de balón. La descripción de la información se basó en valores de frecuencia absoluta y relativa. El contraste de datos por temporada y periodo de juego se hizo con base en las técnicas no paramétricas U-test, test de Friedman y el Chi 2. En todos los casos se utilizó el SPSS versión 15.0 con un nivel de significancia de p ≤ 0,05. Los resultados mostraron un mejor perfil de rendimiento técnico en la temporada 2008, caracterizándose por mejores porcentajes en tiros de 2, tiros libres, menor número de pérdidas de balón y mayor cantidad de robos del balón y asistencias. En relación con el periodo de juego, el equipo mostró un mejor perfil de rendimiento técnico durante los segundos tiempos del partido. En general, el porcentaje de efectividad de tiros de 2 y tiros libres estuvo arriba del 60 % en ambos periodos de juego, mientras que el porcentaje de tiros de 3 osciló entre el 26.4 % y el 29.2 %. En conclusión, el equipo mostró un perfil de rendimiento técnico similar al reportado en la literatura y deja clara evidencia de la importancia que tiene el registro y seguimiento de los indicadores de rendimiento técnico en el baloncesto.

Height-integrated Pedersen and Hall conductivity patterns inferred from the TIROS-NOAA satellite data

International Nuclear Information System (INIS)

Fuller-Rowell, T.J.; Evans, D.S.

1987-01-01

The series of polar-orbiting National Oceanic and Atmospheric Administration spacecraft TIROS, NOAA 6, and NOAA 7 have been monitoring the particle influx into the atmosphere since late 1978. This data base has been used to construct statistical global patterns of height-integrated Pedersen and Hall conductivities for a discrete set of auroral activity ranges. The observations of energy influx and ''characteristic electron energy'' have been binned in a 1 0 latitude and 2 0 magnetic local time grid and ordered by an auroral activity index. This index is an estimate of the energy deposited into a single hemisphere by incident particles, a parameter generated directly from the particle observations and, therefore, internally consistent with the statistical patterns that are constructed. An average electron spectrum is associated with each characteristic energy, which enables a height profile of ionization rate in the upper atmosphere to be determined. The use of a pressure coordinate system insures that the normalized ionization rate profiles are independent of atmospheric model parameters. To create the statistical pattern of height-integrated conductivities, however, vertical profiles of atmospheric temperature and composition are assumed, and the ion density enhancements are evaluated from a chemical balance between ion production and recombination based on an ''effective'' recombination coefficient. The data base can also provide the statistical pattern of particle heating rates and ionization rates over a three-dimensional grid suitable as input to more sophisticated ionospheric and neutral thermospheric codes. copyright American Geophysical Union

Vertical architecture for enhancement mode power transistors based on GaN nanowires

Science.gov (United States)

Yu, F.; Rümmler, D.; Hartmann, J.; Caccamo, L.; Schimpke, T.; Strassburg, M.; Gad, A. E.; Bakin, A.; Wehmann, H.-H.; Witzigmann, B.; Wasisto, H. S.; Waag, A.

2016-05-01

The demonstration of vertical GaN wrap-around gated field-effect transistors using GaN nanowires is reported. The nanowires with smooth a-plane sidewalls have hexagonal geometry made by top-down etching. A 7-nanowire transistor exhibits enhancement mode operation with threshold voltage of 1.2 V, on/off current ratio as high as 108, and subthreshold slope as small as 68 mV/dec. Although there is space charge limited current behavior at small source-drain voltages (Vds), the drain current (Id) and transconductance (gm) reach up to 314 mA/mm and 125 mS/mm, respectively, when normalized with hexagonal nanowire circumference. The measured breakdown voltage is around 140 V. This vertical approach provides a way to next-generation GaN-based power devices.

Evaluación ultrasonográfica del espesor conjunto útero placentario en yeguas de raza de tiro Ardenés, Región de Valparaíso, Chile

Directory of Open Access Journals (Sweden)

Jorge Lohse

2016-03-01

Full Text Available El presente estudio se realizó con el objetivo de estandarizar medidas de espesor conjunto útero placentario (ECUP, en yeguas de raza Ardenes entre el 5° y último mes de gestación siendo el primer estudio de esta medición en esta raza de tipo de tiro, éste fue desarrollado en un haras de la región de Valparaiso, Chile. Un total de 61 yeguas gestantes, clínicamente sanas de raza Ardenés, escogidas al azar y con edades que fluctuaron entre 4 a 18 años, fueron ecografiadas por vía transrectal, para determinar el ECUP, lo cual fue realizado por un solo examinador durante la temporada de parición 2009-2010. La medición de dicho parámetro se realizó con equipo de ultrasonografía análogo, con un transductor lineal de frecuencia 6.0/8.0 MHz. Este procedimiento se repitió 3 veces y con estas medidas se obtuvo un promedio individual. Los resultados fueron descritos en promedios y desviación estándar. Los valores obtenidos en promedio para cada mes son los siguientes: 3,75 mm al 5° mes (121 a 150 días; 3,98 mm al 6° mes (151 a 180 días; 4,02 mm al 7° mes (181 a 210 días; 4,50 mm al 8° mes (211 a 240 días; 4,71 mm al 9° mes (241 a 270 días; 5,02 mm al 10° mes (271 a 300 días; 8,10 mm al 11er mes (301-330 días; 9,73 mm al 12° mes (331 a 360 días. Se concluye que no hubo una variación significativa en el grosor del ECUP en los distintos meses del segundo tercio de gestación, y tampoco hay mayor diferencia comparando estas mediciones con otras razas equinas mencionado en la literatura.

TRANSMISIÓN VERTICAL DE HTLV-1 EN EL PERÚ

Science.gov (United States)

Villaverde, Jorge Alarcón; Romaní, Franco Romaní; Torres, Silvia Montano; Zunt, Joseph R.

2012-01-01

La infección por el virus linfotrópico humano de células T tipo 1 (HTLV-1) ha sido descrita en muchas áreas del mundo, como en los países del Caribe, Japón, África, Oceanía y en Sudamérica. En la presente revisión definimos la endemicidad del HTLV-1 en el país, planteando cuatro criterios epidemiológicos. Luego discutimos el tema central de la revisión: la transmisión vertical del HTLV-1, que en nuestro país sería uno de los principales mecanismos de transmisión. Dentro del desarrollo de este aspecto en particular, presentamos una estimación de la tasa de transmisión vertical y los factores de riesgo asociados con la transmisión vertical sobre la base de una revisión exhaustiva de estudios nacionales y extranjeros. Con esta revisión pretendemos dar una primera aproximación al estudio de la trasmisión vertical de HTLV-1, un aspecto poco estudiado en nuestro medio. PMID:21537777

Continuum limit of gl(M vertical stroke N) spin chains

International Nuclear Information System (INIS)

Candu, Constantin

2011-03-01

We study the spectrum of an integrable antiferromagnetic Hamiltonian of the gl(M vertical stroke N) spin chain of alternating fundamental and dual representations. After extensive numerical analysis, we identify the vacuum and low lying excitations and with this knowledge perform the continuum limit, while keeping a finite gap. All antiferromagnetic gl(n+N vertical stroke N) spin chains with n>0 and N≠0 are shown to possess in the continuum limit 2n-2 multiplets of massive particles which scatter with gl(n) Gross-Neveu like S-matrices, namely their eigenvalues do not depend on N. We argue that the continuum theory is the gl(M vertical stroke N) Gross-Neveu model, that is the massive deformation of the gl(M vertical stroke N) 1 Wess-Zumino-Witten model. As we can see ion the example of gl(2m vertical stroke 1) spin chains, the full particle spectrum is much richer. Our analysis suggests that for a complete characterization of the latter it is not enough to restrict to large volume calculations, as we do in this work. (orig.)

Continuum limit of gl(M vertical stroke N) spin chains

Energy Technology Data Exchange (ETDEWEB)

Candu, Constantin [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany). Gruppe Theorie

2011-03-15

We study the spectrum of an integrable antiferromagnetic Hamiltonian of the gl(M vertical stroke N) spin chain of alternating fundamental and dual representations. After extensive numerical analysis, we identify the vacuum and low lying excitations and with this knowledge perform the continuum limit, while keeping a finite gap. All antiferromagnetic gl(n+N vertical stroke N) spin chains with n>0 and N{ne}0 are shown to possess in the continuum limit 2n-2 multiplets of massive particles which scatter with gl(n) Gross-Neveu like S-matrices, namely their eigenvalues do not depend on N. We argue that the continuum theory is the gl(M vertical stroke N) Gross-Neveu model, that is the massive deformation of the gl(M vertical stroke N){sub 1} Wess-Zumino-Witten model. As we can see ion the example of gl(2m vertical stroke 1) spin chains, the full particle spectrum is much richer. Our analysis suggests that for a complete characterization of the latter it is not enough to restrict to large volume calculations, as we do in this work. (orig.)

Vertical GaN Devices for Power Electronics in Extreme Environments

Science.gov (United States)

2016-03-31

Vertical GaN Devices for Power Electronics in Extreme Environments Isik C. Kizilyalli (1), Robert J. Kaplar (2), O. Aktas (1), A. M. Armstrong (2...electronics applications. In this paper vertical p-n diodes and transistors fabricated on pseudo bulk low defect density (104 to 106 cm-2) GaN substrates are...discussed. Homoepitaxial MOCVD growth of GaN on its native substrate and being able to control doping has allowed the realization of vertical

Kui oluliseks isikuandmete kaitsmist kooli oludes peate ja millest seda tehes lähtute? / Harri Kõo, Ene Tannberg, Kalle Niinas, Maria Tiro...[jt.

Index Scriptorium Estoniae

2008-01-01

Küsimusele vastavad Tabasalu Ühisgümnaasiumi direktor Harri Kõo, Tartu Miina Härma Gümnaasiumi direktor Ene Tannberg, Jakob Westholmi Gümnaasiumi direktor Kalle Niinas, Jüri Gümnaasiumi direktor Maria Tiro ja Viimsi Keskkooli direktor Leelo Tiisvelt

Análisis de la eficacia de los saques de esquina en la copa del mundo de fútbol 2010. Un intento de identificación de variables explicativas

Directory of Open Access Journals (Sweden)

Toni Ard\\u00E1 Su\\u00E1rez

2014-01-01

Full Text Available En el fútbol, ​​balón parado movimientos son aquellos en los que se devuelve la pelota para jugar desde una posición estacionaria después de una interrupción de juego. Theaim de este estudio fue analizar la eficacia de una medida de este tipo a balón parado, es decir, tiros de esquina, y para identificar las variables clave que determinan thesuccess de un tiro o de cabecera tras una esquina, lo que permite un modelo de saques de esquina exitosas que se propondrán . Se registraron 554 tiros de esquina Performe dduring la Copa Mundial 2010 en Sudáfrica, y se realizó un análisis univariado, bivariado y multivariado de los datos. Los resultados indicaron que las esquinas eran de eficacia limitada en términos del éxito de disparos o cabeceras posteriores. El análisis también reveló una serie de variables que se relacionaron significativamente con los otros, y esto nos ha permitido proponer un modelo explicativo. Aunque este modelo se había limitado poder explicativo, no obstante ayuda tounder destacan la ejecución de tiros de esquina en términos prácticos.

Contribución de los brazos en el aterrizaje del salto vertical. [Contribution of the arms in the landing of the vertical jump].

Directory of Open Access Journals (Sweden)

Marcos Gutiérrez-Dávila

2018-04-01

Full Text Available Se pretende comprobar el efecto que tiene la contribución de los brazos en los aterrizajes de los saltos verticales sobre las componentes de las fuerzas de reacción, goniometría articular y contribución de los segmentos corporales al desplazamiento vertical del centro de gravedad (CG. Han participado 29 deportistas donde el salto vertical constituye una habilidad básica. Todos los participantes debían dejarse caer desde una altura de 0.5 m y amortiguar la caída en dos situaciones experimentales: a sin acción de brazos y b con participación libre de los brazos. Se ha utilizado una plataforma de fuerza, operando a 500 Hz, sincronizada temporalmente a una cámara de vídeo a 240 Hz que registraba el plano sagital de los saltos. Los saltos han sido considerados como un movimiento simétrico que se desarrolla en un plano, compuesto por un modelo mecánico simplificado de ocho segmentos. Los resultados han puesto de manifiesto que la participación libre de los brazos contribuye a reducir del segundo pico máximo de fuerza, lo que se produce debido a la mayor distancia de frenado del CG y una menor reducción de la velocidad vertical del CG, lo que podría contribuir a reducir el riesgo de lesiones. La contribución segmentaria al desplazamiento vertical del CG indica que la restricción de los brazos durante los aterrizajes produce un cambio importante en el mecanismo de absorción de las fuerzas que podría incrementar la tensión en el ligamento cruzado anterior de la rodilla. Abstract The purpose was to evaluate the effect of the arms action during vertical jump landing on ground reaction forces, joint kinematic and vertical displacement of the center of gravity (CG. 29 athletes where the vertical jump constitutes a basic skill in their sport have participated in this study. All participants had to drop from a height of 0.5 m and cushion the fall in two experimental situations: a without arm action and b with free participation of the

OS EFEITOS DO TREINO DE TIRO COM ZARABATANA NA CAPACIDADE RESPIRATÓRIA DE PESSOAS COM TRISSOMIA 21 APÓS UM ANO DE DESTREINO

Directory of Open Access Journals (Sweden)

C. Leitão

2015-05-01

Full Text Available Em 2011 estimava-se que houvesse entre 12 a 15 mil crianças com Trissomia 21 (Martinho, 2011. A capacidade respiratória está relacionada com a permuta do ar atmosférico com o ar existente no interior dos pulmões (McArdle, Katch & Katch, 2001, sendo que este processo apresenta-se mais dificultado em sujeitos com Trissomia 21 pois exibem valores de pressão expiratória máxima abaixo dos 50% e de pressão inspiratória máxima abaixo dos 60% previstos para a população sedentária saudável (Castoldi, Périco & Grave, 2012. O treino de tiro com zarabatana tem influência no aumento da pressão expiratória máxima e tem um efeito sobre a função respiratória, semelhante ao treino muscular de músculos expiratório em adultos (Nagasaki, Okada, Kai, & Takahashi, 2010. Segundo (Mariñas & Higuchi, 2010 a zarabatana trata-se de um tubo comprido, através do qual são expelidos pequenos projéteis, através do sopro com objetivo de atingir um alvo. A introdução da atividade de tiro com zarabatana surge de modo a minimizar os problemas respiratórios desta população, porque envolve todo o ciclo respiratório e por ser uma atividade lúdica. Objetivo: Comparar os efeitos do treino de tiro com zarabatana na capacidade respiratória de pessoas com trissomia 21 após um ano de destreino.

Determinación astronómica de la Desviación de la Vertical

Science.gov (United States)

Pacheco, A. M.; Podestá, R. C.

A partir de las coordenadas astronómicas de Latitud y Longitud determinadas en la falla geológica de Nikizanga ubicada en las serranías de Pie de Palo, y, en base a un Punto Datum de referencia, se desarrolla la metodología para la determinación de la Desviación de la Vertical, que comprende la reducción de las observaciones astronómicas, transformaciones de coordenadas, aplicación de correcciones y el cálculo definitivo de los valores angulares de la Vertical. Estos estudios se iniciaron a sugerencia del Servicio Internacional de Latitud, International Polar Motion Service (IPMS), con el objeto de obtener en determinados puntos de la Tierra la Desviación de la Vertical y su variación, dentro de la nueva disciplina denominada Astrogeodinámica, con la idea de correlacionar estas variaciones con la predicción de grandes sismos.

COMPUTING VERTICES OF INTEGER PARTITION POLYTOPES

Directory of Open Access Journals (Sweden)

A. S. Vroublevski

2015-01-01

Full Text Available The paper describes a method of generating vertices of the polytopes of integer partitions that was used by the authors to calculate all vertices and support vertices of the partition polytopes for all n ≤ 105 and all knapsack partitions of n ≤ 165. The method avoids generating all partitions of n. The vertices are determined with the help of sufficient and necessary conditions; in the hard cases, the well-known program Polymake is used. Some computational aspects are exposed in more detail. These are the algorithm for checking the criterion that characterizes partitions that are convex combinations of two other partitions; the way of using two combinatorial operations that transform the known vertices to the new ones; and employing the Polymake to recognize a limited number (for small n of partitions that need three or more other partitions for being convexly expressed. We discuss the computational results on the numbers of vertices and support vertices of the partition polytopes and some appealing problems these results give rise to.

Alpha absolute power: motor learning of practical pistol shooting Potência absoluta de alfa: aprendizagem motora do tiro prático de pistola

Directory of Open Access Journals (Sweden)

Clayton Amaral Domingues

2008-06-01

Full Text Available The present study aimed at investigating changes in behavior (shooting precision and electrophysiological variables (absolute alpha power during the motor learning of practical pistol shooting. The sample was composed of 23 healthy subjects, right-handed, male, between 18 and 20 years of age. The task consisted of four learning blocks. A One-way ANOVA with repeated measures and a post hoc analysis were employed to observe modifications on behavioral and electrophysiological measures (pO presente estudo teve por objetivo investigar alterações nas variáveis comportamentais (precisão do tiro e eletrofisiológicas (potência absoluta de alfa durante o aprendizado motor do tiro prático de pistola. A amostra constituiu-se de 20 sujeitos saudáveis, destros, sexo masculino, faixa etária entre 18 e 20 anos. A tarefa consistiu de quatro blocos de aprendizagem. A análise estatística das variáveis comportamentais e eletrofisiológicas foram realizadas por meio de uma ANOVA one-way e uma análise post hoc (p<0,05. Os resultados demonstraram diferenças significativas entre os blocos em função do aprendizado motor, bem como uma sensível melhora na precisão do tiro de ambos os blocos. Foi observada uma diminuição na potência de alfa em todos os eletrodos analisados durante a execução da tarefa, quando comparados aos blocos de linha de base e controle da aprendizagem. Os achados sugerem que a potência em alfa diminui devido o aprendizado motor quando sujeitos estão engajados na execução de uma tarefa motora complexa.

Características metabólicas del músculoGluteus medius de equinos mestizos con aptitud de tiro

OpenAIRE

MERINO, V.; ISLAS, A.; LOPEZ-RIVERO, J.; MORA, G.; QUEZADA, M.; LOPEZ, J.; REYES, J.

1998-01-01

De 16 equinos mestizos de tiro, de ambos sexos, clínicamente sanos, se obtuvieron biopsias del músculo Gluteus medius a 3, 6 y 9 cm de profundidad, con el objetivo de evaluar su metabolismo anaeróbico y aeróbico, determinando las actividades de las enzimas creatinquinasa (CK), deshidrogenasa láctica (LDH) y citrato sintetasa (CS) en animales inactivos y trabajando en faenas agrícolas. El tejido muscular se homogeneizó, sonicó y centrifugó; posteriormente en el sobrenadante se determinaron la...

Contribución segmentaria de los saltos con contramovimiento en vertical y en horizontal. [Segmental contribution on countermovement vertical and horizontal jumps].

Directory of Open Access Journals (Sweden)

Marcos Gutiérrez-Dávila

2014-10-01

Full Text Available El propósito ha sido realizar un análisis dinámico y cinemático sobre los saltos verticales (SV y horizontales (SH y cuantificar la aportación de los segmentos corporales al desplazamiento del centro de masa (CM durante la fase de propulsión. Han participado 28 deportistas practicantes de modalidades deportivas donde el salto vertical constituye una habilidad básica. Se ha utilizado una plataforma de fuerza, operando a 500 Hz, sincronizada temporalmente a una cámara de vídeo a 210 Hz que registraba el plano sagital de los saltos. Los saltos han sido considerados como un movimiento simétrico que se desarrolla en un plano, compuesto por un modelo mecánico coordinado simplificado de ocho segmentos. En la condición SV, los participantes debían de realizar un salto vertical máximo partiendo de una posición erguida sobre la plataforma de fuerza. En la condición SH, los participantes debían realizar un salto máximo en horizontal desde la misma posición. El tiempo de batida ha sido superior en SH con respecto a SV, (0.898 vs 1.056 s, constatándose una estrategia de rotación-extensión para SH. Los resultados ponen de manifiesto que la fuerza neta ejercida durante el impulso de frenado es mayor para SV debido a la mayor velocidad radial al inicio del impulso de frenado (-1.166 vs -0.992 m/s. Existe una mayor participación de las articulaciones del tobillo y la cadera plasmada en la mayor contribución del tronco en SH durante toda la batida, además de constatarse una mayor contribución de las extremidades superiores al desplazamiento vertical del CM en SV. Abstract The main aim of this research was a dynamics and kinematics analysis of vertical (SV and horizontal (SH jumps and quantify the body segments’ contribution to center of mass, CM, displacement during the propulsion phase. 28 athletes from different sport modalities where the vertical jump is a basic skill have participated. We used a force platform, operating at 500 Hz

Ensayos de calefacción por «glorias»

Directory of Open Access Journals (Sweden)

Laorden, J.

1961-01-01

Full Text Available En el presente trabajo se describen los ensayos realizados haciendo circular los humos de una chimenea a través de un suelo hueco para calentarlo. Los humos salen de la chimenea, recorren el suelo de las habitaciones y vuelven a la chimenea para ser expulsados al exterior. Esta circulación indirecta de los humos se hace, bien por tiro natural de los humos o mediante un tiro forzado provocando por un ventilador axial. Los ensayos han demostrado que los humos pueden calentar una superficie de unos 40 metros cuadrados de suelo. Volviendo otra vez al origen, pero hace falta emplear el ventilador para conseguir que no haya revoco de los humos dentro de la habitación en que está el hogar.

Space environment monitoring by low-altitude operational satellites

International Nuclear Information System (INIS)

Kroehl, H.W.

1982-01-01

The primary task of the Defense Meteorological Satellite Program (DMSP) is the acquisition of meteorological data in the visual and infrared spectral regions. The Air Weather Service operates two satellites in low-altitude, sun-synchronous, polar orbits at 850 km altitude, 98.7 deg inclination, 101.5 minute period and dawn-dusk or noon-midnight equatorial crossing times. Special DMSP sensors of interest to the space science community are the precipitating electron spectrometer, the terrestrial noise receiver, and the topside ionosphere plasma monitor. Data from low-altitude, meteorological satellites can be used to build empirical models of precipitating electron characteristics of the auroral zone and polar cap. The Tiros-NOAA satellite program complements the DMSP program. The orbital elements are the same as DMSP's, except for the times of equatorial crossing, and the tilt of the orbital plane. The Tiros-NOAA program meets the civilian community's needs for meteorological data as the DMSP program does for the military

Vertical elliptic operator for efficient wave propagation in TTI media

KAUST Repository

Waheed, Umair bin; Alkhalifah, Tariq Ali

2015-01-01

Elliptic wave extrapolation operators require significantly less computational cost than the ones for transversely isotropic (TI) media. However, it does not provide accurate wavefield representation or imaging for the prevalent TI media. We propose a new vertical elliptically anisotropic (VEA) wave equation by decomposing the acoustic TI pseudo-differential wave equation. The decomposition results in a vertical elliptic differential equation and a scalar operator. The new VEA-like wave equation shares the same dispersion relation as that of the original acoustic TI wave equation. Therefore, the kinematic contents are correctly matched to the original equation. Moreover, the proposed decomposition yields better amplitude properties than the isotropic decomposition without increasing the computational load. Therefore, it exhibits better cost versus accuracy tradeoff compared to the isotropic or the tilted elliptic decompositions. We demonstrate with numerical examples that the proposed methodology is numerically stable for complex models and is free from shear-wave artifacts.

Vertical elliptic operator for efficient wave propagation in TTI media

KAUST Repository

Waheed, Umair bin

2015-08-19

Elliptic wave extrapolation operators require significantly less computational cost than the ones for transversely isotropic (TI) media. However, it does not provide accurate wavefield representation or imaging for the prevalent TI media. We propose a new vertical elliptically anisotropic (VEA) wave equation by decomposing the acoustic TI pseudo-differential wave equation. The decomposition results in a vertical elliptic differential equation and a scalar operator. The new VEA-like wave equation shares the same dispersion relation as that of the original acoustic TI wave equation. Therefore, the kinematic contents are correctly matched to the original equation. Moreover, the proposed decomposition yields better amplitude properties than the isotropic decomposition without increasing the computational load. Therefore, it exhibits better cost versus accuracy tradeoff compared to the isotropic or the tilted elliptic decompositions. We demonstrate with numerical examples that the proposed methodology is numerically stable for complex models and is free from shear-wave artifacts.

The effects of tirofiban infusion on clinical and angiographic outcomes of patients with STEMI undergoing primary PCI.

Science.gov (United States)

Kaymaz, Cihangir; Keleş, Nurşen; Özdemir, Nihal; Tanboğa, İbrahim Halil; Demircan, Hacer C; Can, Mehmet M; Koca, Fatih; İzgi, İbrahim Akın; Özkan, Alper; Türkmen, Muhsin; Kırma, Cevat; Esen, Ali M

2015-11-01

The present study was designed to determine the effects of tirofiban (Tiro) infusion on angiographic measures, ST-segment resolution, and clinical outcomes in patients with STEMI undergoing PCI. Glycoprotein (GP) IIb/IIIa inhibitors are beneficial in ST-segment elevation myocardial infarction (STEMI) patients undergoing percutaneous coronary intervention (PCI), while the most effective timing of administration is still under investigation. A total of 1242 patients (83.0% males, mean (standard deviation; SD) age: 54.7 (10.9) years) with STEMI who underwent primary PCI were included in this retrospective non-randomized study in four groups, composed of no tirofiban infusion [Tiro (-); n=248], tirofiban infusion before PCI (pre-Tiro; n=720), tirofiban infusion during PCI (peri-Tiro; n=50), and tirofiban infusion after PCI (post-Tiro; n=224). In all Tiro (+) patients, bolus administration of Tiro (10 µg/kg) was followed by infusion (0.15 µg/kg/min) for a mean (SD) duration of 22.4±6.8 hours. The pre-PCI Tiro group was associated with the highest percentage of patients with TIMI 3 flow (99.4%; p75% ST-segment resolution (78.1%; pPCI significantly improves myocardial reperfusion, ST-segment resolution, in-hospital mortality rate, and in-hospital sudden cardiac death in patients with STEMI with no increased risk of major bleeding.

A case study of the sensitivity of forecast skill to data and data analysis techniques

Science.gov (United States)

Baker, W. E.; Atlas, R.; Halem, M.; Susskind, J.

1983-01-01

A series of experiments have been conducted to examine the sensitivity of forecast skill to various data and data analysis techniques for the 0000 GMT case of January 21, 1979. These include the individual components of the FGGE observing system, the temperatures obtained with different satellite retrieval methods, and the method of vertical interpolation between the mandatory pressure analysis levels and the model sigma levels. It is found that NESS TIROS-N infrared retrievals seriously degrade a rawinsonde-only analysis over land, resulting in a poorer forecast over North America. Less degradation in the 72-hr forecast skill at sea level and some improvement at 500 mb is noted, relative to the control with TIROS-N retrievals produced with a physical inversion method which utilizes a 6-hr forecast first guess. NESS VTPR oceanic retrievals lead to an improved forecast over North America when added to the control.

Similar failure rate in immediate post-operative weight bearing versus protected weight bearing following meniscal repair on peripheral, vertical meniscal tears.

Science.gov (United States)

Perkins, Bryan; Gronbeck, Kyle R; Yue, Ruixian Alexander; Tompkins, Marc A

2017-08-16

Post-operative weight bearing after meniscal repair is a point of debate among physicians. This study sought to evaluate whether patients adhering to an immediate WBAT rehabilitation programme have a higher failure rate compared to those adhering to a more traditional, protected, NWB status following meniscal repair. The null hypothesis was that there would be no difference in failure between the two groups. A retrospective review of meniscal repair patients greater than 5 years from surgery was performed for patients receiving meniscal repair treatment. Patients were categorized by post-surgical weight-bearing status, either NWB or WBAT, and then analysed for failure of repair. Failure was defined as re-operation on the torn meniscus. The study controlled for variables including age at surgery, sex, height, weight, and BMI, classification of tear type, acuity of the tear, repair location (medial or lateral), repair location within the meniscus, repair technique, and concomitant procedures. Re-operations were performed in 61 of 157 patients [38.9%]. There was no difference between weight-bearing groups for failure of meniscus repair (n.s.). The tears were acute vertical tears located in the posterior horn and body. For the 61 patients with re-operation, the average time to re-operation was 2.2 years with 10 [16%] > 5 years from surgery, 17 [28%] 2-5 years from surgery, and 34 [56%] bearing groups for rate of re-operation (n.s.). Weight bearing as tolerated after meniscal repair for peripheral, vertical tears does not result in a higher failure rate than traditional, non-weight bearing over a five-year follow-up period. The clinical relevance is that, based on these data, it may be appropriate to allow weight bearing as tolerated following meniscal repair of peripheral, vertical tears. Retrospective cohort study, Level III.

Characterization of vertical GaN p-n diodes and junction field-effect transistors on bulk GaN down to cryogenic temperatures

Science.gov (United States)

Kizilyalli, I. C.; Aktas, O.

2015-12-01

There is great interest in wide-bandgap semiconductor devices and most recently in vertical GaN structures for power electronic applications such as power supplies, solar inverters and motor drives. In this paper the temperature-dependent electrical behavior of vertical GaN p-n diodes and vertical junction field-effect transistors fabricated on bulk GaN substrates of low defect density (104 to 106 cm-2) is described. Homoepitaxial MOCVD growth of GaN on its native substrate and the ability to control the doping in the drift layers in GaN have allowed the realization of vertical device architectures with drift layer thicknesses of 6 to 40 μm and net carrier electron concentrations as low as 1 × 1015 cm-3. This parameter range is suitable for applications requiring breakdown voltages of 1.2 kV to 5 kV. Mg, which is used as a p-type dopant in GaN, is a relatively deep acceptor (E A ≈ 0.18 eV) and susceptible to freeze-out at temperatures below 200 K. The loss of holes in p-GaN has a deleterious effect on p-n junction behavior, p-GaN contacts and channel control in junction field-effect transistors at temperatures below 200 K. Impact ionization-based avalanche breakdown (BV > 1200 V) in GaN p-n junctions is characterized between 77 K and 423 K for the first time. At higher temperatures the p-n junction breakdown voltage improves due to increased phonon scattering. A positive temperature coefficient in the breakdown voltage is demonstrated down to 77 K; however, the device breakdown characteristics are not as abrupt at temperatures below 200 K. On the other hand, contact resistance to p-GaN is reduced dramatically above room temperature, improving the overall device performance in GaN p-n diodes in all cases except where the n-type drift region resistance dominates the total forward resistance. In this case, the electron mobility can be deconvolved and is found to decrease with T -3/2, consistent with a phonon scattering model. Also, normally-on vertical junction

Analysis of the AlGaN/GaN vertical bulk current on Si, sapphire, and free-standing GaN substrates

International Nuclear Information System (INIS)

Pérez-Tomás, A.; Fontserè, A.; Llobet, J.; Placidi, M.; Rennesson, S.; Chenot, S.; Moreno, J. C.; Cordier, Y.; Baron, N.

2013-01-01

The vertical bulk (drain-bulk) current (I db ) properties of analogous AlGaN/GaN hetero-structures molecular beam epitaxially grown on silicon, sapphire, and free-standing GaN (FS-GaN) have been evaluated in this paper. The experimental I db (25–300 °C) have been well reproduced with physical models based on a combination of Poole-Frenkel (trap assisted) and hopping (resistive) conduction mechanisms. The thermal activation energies (E a ), the (soft or destructive) vertical breakdown voltage (V B ), and the effect of inverting the drain-bulk polarity have also been comparatively investigated. GaN-on-FS-GaN appears to adhere to the resistive mechanism (E a = 0.35 eV at T = 25–300 °C; V B = 840 V), GaN-on-sapphire follows the trap assisted mechanism (E a = 2.5 eV at T > 265 °C; V B > 1100 V), and the GaN-on-Si is well reproduced with a combination of the two mechanisms (E a = 0.35 eV at T > 150 °C; V B = 420 V). Finally, the relationship between the vertical bulk current and the lateral AlGaN/GaN transistor leakage current is explored.

Characterization of vertical GaN p–n diodes and junction field-effect transistors on bulk GaN down to cryogenic temperatures

International Nuclear Information System (INIS)

Kizilyalli, I C; Aktas, O

2015-01-01

There is great interest in wide-bandgap semiconductor devices and most recently in vertical GaN structures for power electronic applications such as power supplies, solar inverters and motor drives. In this paper the temperature-dependent electrical behavior of vertical GaN p–n diodes and vertical junction field-effect transistors fabricated on bulk GaN substrates of low defect density (10 4 to 10 6 cm −2 ) is described. Homoepitaxial MOCVD growth of GaN on its native substrate and the ability to control the doping in the drift layers in GaN have allowed the realization of vertical device architectures with drift layer thicknesses of 6 to 40 μm and net carrier electron concentrations as low as 1 × 10 15 cm −3 . This parameter range is suitable for applications requiring breakdown voltages of 1.2 kV to 5 kV. Mg, which is used as a p-type dopant in GaN, is a relatively deep acceptor (E A  ≈ 0.18 eV) and susceptible to freeze-out at temperatures below 200 K. The loss of holes in p-GaN has a deleterious effect on p–n junction behavior, p-GaN contacts and channel control in junction field-effect transistors at temperatures below 200 K. Impact ionization-based avalanche breakdown (BV > 1200 V) in GaN p–n junctions is characterized between 77 K and 423 K for the first time. At higher temperatures the p–n junction breakdown voltage improves due to increased phonon scattering. A positive temperature coefficient in the breakdown voltage is demonstrated down to 77 K; however, the device breakdown characteristics are not as abrupt at temperatures below 200 K. On the other hand, contact resistance to p-GaN is reduced dramatically above room temperature, improving the overall device performance in GaN p–n diodes in all cases except where the n-type drift region resistance dominates the total forward resistance. In this case, the electron mobility can be deconvolved and is found to decrease with T −3/2 , consistent with a phonon scattering model. Also

Monolithic Flexible Vertical GaN Light-Emitting Diodes for a Transparent Wireless Brain Optical Stimulator.

Science.gov (United States)

Lee, Han Eol; Choi, JeHyuk; Lee, Seung Hyun; Jeong, Minju; Shin, Jung Ho; Joe, Daniel J; Kim, DoHyun; Kim, Chang Wan; Park, Jung Hwan; Lee, Jae Hee; Kim, Daesoo; Shin, Chan-Soo; Lee, Keon Jae

2018-05-18

Flexible inorganic-based micro light-emitting diodes (µLEDs) are emerging as a significant technology for flexible displays, which is an important area for bilateral visual communication in the upcoming Internet of Things era. Conventional flexible lateral µLEDs have been investigated by several researchers, but still have significant issues of power consumption, thermal stability, lifetime, and light-extraction efficiency on plastics. Here, high-performance flexible vertical GaN light-emitting diodes (LEDs) are demonstrated by silver nanowire networks and monolithic fabrication. Transparent, ultrathin GaN LED arrays adhere to a human fingernail and stably glow without any mechanical deformation. Experimental studies provide outstanding characteristics of the flexible vertical μLEDs (f-VLEDs) with high optical power (30 mW mm -2 ), long lifetime (≈12 years), and good thermal/mechanical stability (100 000 bending/unbending cycles). The wireless light-emitting system on the human skin is successfully realized by transferring the electrical power f-VLED. Finally, the high-density GaN f-VLED arrays are inserted onto a living mouse cortex and operated without significant histological damage of brain. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Multi-Agent Pathfinding with n Agents on Graphs with n Vertices

DEFF Research Database (Denmark)

Förster, Klaus-Tycho; Groner, Linus; Hoefler, Torsten

2017-01-01

We investigate the multi-agent pathfinding (MAPF) problem with $n$ agents on graphs with $n$ vertices: Each agent has a unique start and goal vertex, with the objective of moving all agents in parallel movements to their goal s.t.~each vertex and each edge may only be used by one agent at a time....... We give a combinatorial classification of all graphs where this problem is solvable in general, including cases where the solvability depends on the initial agent placement. Furthermore, we present an algorithm solving the MAPF problem in our setting, requiring O(n²) rounds, or O(n³) moves...... of individual agents. Complementing these results, we show that there are graphs where Omega(n²) rounds and Omega(n³) moves are required for any algorithm....

Leakage current reduction of vertical GaN junction barrier Schottky diodes using dual-anode process

Science.gov (United States)

Hayashida, Tetsuro; Nanjo, Takuma; Furukawa, Akihiko; Watahiki, Tatsuro; Yamamuka, Mikio

2018-04-01

The origin of the leakage current of a trench-type vertical GaN diode was discussed. We found that the edge of p-GaN is the main leakage spot. To reduce the reverse leakage current at the edge of p-GaN, a dual-anode process was proposed. As a result, the reverse blocking voltage defined at the leakage current density of 1 mA/cm2 of a vertical GaN junction barrier Schottky (JBS) diode was improved from 780 to 1,190 V, which is the highest value ever reported for vertical GaN Schottky barrier diodes (SBDs).

Combined ground- and satellite-based profiling of temperature and water vapor

International Nuclear Information System (INIS)

Stankov, B.B.; Westwater, E.R.; Snider, J.B.; Churnside, J.H.

1994-01-01

The fusion or integration of meteorological and radiative data from a range of instrumentation into a representative picture of temperature, water vapor, and clouds over a CART domain will be a challenging task for four-dimensional data assimilation models. In the work reported here, we have summarized work supported by DOE's algorithm development program including combined RASS and TIROS Operational Vertical Sounder (TOVS) temperature sensing, water vapor profiles from dual-channel radiometers, and neural network radiometric temperature retrievals

Development and operation of a real-time simulation at the NASA Ames Vertical Motion Simulator

Science.gov (United States)

Sweeney, Christopher; Sheppard, Shirin; Chetelat, Monique

1993-01-01

The Vertical Motion Simulator (VMS) facility at the NASA Ames Research Center combines the largest vertical motion capability in the world with a flexible real-time operating system allowing research to be conducted quickly and effectively. Due to the diverse nature of the aircraft simulated and the large number of simulations conducted annually, the challenge for the simulation engineer is to develop an accurate real-time simulation in a timely, efficient manner. The SimLab facility and the software tools necessary for an operating simulation will be discussed. Subsequent sections will describe the development process through operation of the simulation; this includes acceptance of the model, validation, integration and production phases.

Interface engineered HfO2-based 3D vertical ReRAM

International Nuclear Information System (INIS)

Hudec, Boris; Wang, I-Ting; Lai, Wei-Li; Chang, Che-Chia; Hou, Tuo-Hung; Jančovič, Peter; Fröhlich, Karol; Mičušík, Matej; Omastová, Mária

2016-01-01

We demonstrate a double-layer 3D vertical resistive random access memory (ReRAM) stack implementing a Pt/HfO 2 /TiN memory cell. The HfO 2 switching layer is grown by atomic layer deposition on the sidewall of a SiO 2 /TiN/SiO 2 /TiN/SiO 2 multilayer pillar. A steep vertical profile was achieved using CMOS-compatible TiN dry etching. We employ in situ TiN bottom interface engineering by ozone, which results in (a) significant forming voltage reduction which allows for forming-free operation in AC pulsed mode, and (b) non-linearity tuning of low resistance state by current compliance during Set operation. The vertical ReRAM shows excellent read and write disturb immunity between vertically stacked cells, retention over 10 4 s and excellent switching stability at 400 K. Endurance of 10 7 write cycles was achieved using 100 ns wide AC pulses while fast switching speed using pulses of only 10 ns width is also demonstrated. The active switching region was evaluated to be located closer to the bottom interface which allows for the observed high endurance. (paper)

Vertically aligned N-doped CNTs growth using Taguchi experimental design

Energy Technology Data Exchange (ETDEWEB)

Silva, Ricardo M. [CICECO, Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro (Portugal); Fernandes, António J.S. [I3 N, Physics Department, University of Aveiro, 3810-193 Aveiro (Portugal); Ferro, Marta C. [CICECO, Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro (Portugal); Pinna, Nicola [Institut für Chemie, Humboldt-Universität zu Berlin, Brook-Taylor-Str. 2, 12489 Berlin Germany (Germany); Silva, Rui F., E-mail: rsilva@ua.pt [CICECO, Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro (Portugal)

2015-07-30

Highlights: • Taguchi method is employed for the CVD growth of vertically aligned N-doped CNTs. • Optimal growth parameters: NH3 = 90 sccm, T = 825 °C and catalyst pretreatment time = 2 min. • SEM and HRTEM revealed VACNTs with bamboo-like structure of curved graphitic layers. • XPS analysis results indicated 2.00 at.% of N incorporation in the VACNTs. - Abstract: The Taguchi method with a parameter design L{sub 9} orthogonal array was implemented for optimizing the nitrogen incorporation in the structure of vertically aligned N-doped CNTs grown by thermal chemical deposition (TCVD). The maximization of the I{sub D}/I{sub G} ratio of the Raman spectra was selected as the target value. As a result, the optimal deposition configuration was NH{sub 3} = 90 sccm, growth temperature = 825 °C and catalyst pretreatment time of 2 min, the first parameter having the main effect on nitrogen incorporation. A confirmation experiment with these values was performed, ratifying the predicted I{sub D}/I{sub G} ratio of 1.42. Scanning electron microscopy (SEM) characterization revealed a uniform completely vertically aligned array of multiwalled CNTs which individually exhibit a bamboo-like structure, consisting of periodically curved graphitic layers, as depicted by high resolution transmission electron microscopy (HRTEM). The X-ray photoelectron spectroscopy (XPS) results indicated a 2.00 at.% of N incorporation in the CNTs in pyridine-like and graphite-like, as the predominant species.

Enhancement of breakdown voltage for fully-vertical GaN-on-Si p-n diode by using strained layer superlattice as drift layer

Science.gov (United States)

Mase, Suguru; Hamada, Takeaki; Freedsman, Joseph J.; Egawa, Takashi

2018-06-01

We have demonstrated a vertical GaN-on-Si p-n diode with breakdown voltage (BV) as high as 839 V by using a low Si-doped strained layer superlattice (SLS). The p-n vertical diode fabricated by using the n‑-SLS layer as a part of the drift layer showed a remarkable enhancement in BV, when compared with the conventional n‑-GaN drift layer of similar thickness. The vertical GaN-on-Si p-n diodes with 2.3 μm-thick n‑-GaN drift layer and 3.0 μm-thick n‑-SLS layer exhibited a differential on-resistance of 4.0 Ω · cm2 and a BV of 839 V.

Piezo-generator integrating a vertical array of GaN nanowires.

Science.gov (United States)

Jamond, N; Chrétien, P; Houzé, F; Lu, L; Largeau, L; Maugain, O; Travers, L; Harmand, J C; Glas, F; Lefeuvre, E; Tchernycheva, M; Gogneau, N

2016-08-12

We demonstrate the first piezo-generator integrating a vertical array of GaN nanowires (NWs). We perform a systematic multi-scale analysis, going from single wire properties to macroscopic device fabrication and characterization, which allows us to establish for GaN NWs the relationship between the material properties and the piezo-generation, and to propose an efficient piezo-generator design. The piezo-conversion of individual MBE-grown p-doped GaN NWs in a dense array is assessed by atomic force microscopy (AFM) equipped with a Resiscope module yielding an average output voltage of 228 ± 120 mV and a maximum value of 350 mV generated per NW. In the case of p-doped GaN NWs, the piezo-generation is achieved when a positive piezo-potential is created inside the nanostructures, i.e. when the NWs are submitted to compressive deformation. The understanding of the piezo-generation mechanism in our GaN NWs, gained from AFM analyses, is applied to design a piezo-generator operated under compressive strain. The device consists of NW arrays of several square millimeters in size embedded into spin-on glass with a Schottky contact for rectification and collection of piezo-generated carriers. The generator delivers a maximum power density of ∼12.7 mW cm(-3). This value sets the new state of the art for piezo-generators based on GaN NWs and more generally on nitride NWs, and offers promising prospects for the use of GaN NWs as high-efficiency ultra-compact energy harvesters.

Integración vertical y contratación externa en los servicios generales de los hospitales españoles

Directory of Open Access Journals (Sweden)

Puig-Junoy J.

2002-01-01

Full Text Available Objetivos: Este estudio analiza los factores que influyen en las decisiones de integración vertical/contratación externa de cuatro servicios generales (limpieza, lavandería, alimentación y seguridad y mantenimiento en los hospitales españoles (3.160 transacciones que corresponden a 790 hospitales. Métodos: Se presenta la estimación empírica de un modelo logístico de maximización de la utilidad de los hospitales, en el que intervienen no sólo factores relacionados con los costes de transacción, sino también otros relacionados con la intervención pública y la dimensión política. Resultados: El 55,7% de los hospitales contrata al menos uno de los servicios generales analizados. El servicio de limpieza es el que presenta un mayor grado de contratación externa (45,1%, seguido del servicio de seguridad y mantenimiento (32,5%. En cambio, el servicio de lavandería es el que presenta un mayor grado de integración vertical (94,3% junto con el de alimentación (80,1%. La dimensión del hospital (economías de escala, medida a través del número de camas, es una de las variables que influyen de forma importante la decisión de integración vertical o contratación externa de los servicios de limpieza, alimentación y mantenimiento y seguridad. Conclusiones: Las economías de escala contribuyen a una mayor integración vertical, mientras que la especialización y el carácter lucrativo favorecen la decisión de contratación externa. El servicio de lavandería tiene un comportamiento diferenciado de los demás, mostrando efectos que indican la posible presencia de activos específicos.

The ergonomics of vertical turret lathe operation.

Science.gov (United States)

Pratt, F M; Corlett, E N

1970-12-01

A study of the work load of 14 vertical turret lathe operators engaged on different work tasks in two factories is reported. For eight of these workers continuous heart rate recordings were made throughout the day. It was shown that in four cases improved technology was unlikely to lead to higher output and certain aspects of posture and equipment manipulation were major contributors to the limitations on increased output. The role of the work-rest schedule in increasing work loads was also demonstrated. Improvements in technology and methods to reduce the extent of certain work loads to enable heavy work to be done in shorter periods followed by light work or rest periods are given as means to modify and improve the output of these machines. Finally, the direction for the development of a predictive model for man-machine matching is introduced.

Vertically integrated (Ga, In)N nanostructures for future single photon emitters operating in the telecommunication wavelength range

International Nuclear Information System (INIS)

Winden, A; Mikulics, M; Grützmacher, D; Hardtdegen, H

2013-01-01

Important technological steps are discussed and realized for future room-temperature operation of III-nitride single photon emitters. First, the growth technology of positioned single pyramidal InN nanostructures capped by Mg-doped GaN is presented. The optimization of their optical characteristics towards narrowband emission in the telecommunication wavelength range is demonstrated. In addition, a device concept and technology was developed so that the nanostructures became singularly addressable. It was found that the nanopyramids emit in the telecommunication wavelength range if their size is chosen appropriately. A p-GaN contacting layer was successfully produced as a cap to the InN pyramids and the top p-contact was achievable using an intrinsically conductive polymer PEDOT:PSS, allowing a 25% increase in light transmittance compared to standard Ni/Au contact technology. Single nanopyramids were successfully integrated into a high-frequency device layout. These decisive technology steps provide a promising route to electrically driven and room-temperature operating InN based single photon emitters in the telecommunication wavelength range. (paper)

High-performance vertical organic transistors.

Science.gov (United States)

Kleemann, Hans; Günther, Alrun A; Leo, Karl; Lüssem, Björn

2013-11-11

Vertical organic thin-film transistors (VOTFTs) are promising devices to overcome the transconductance and cut-off frequency restrictions of horizontal organic thin-film transistors. The basic physical mechanisms of VOTFT operation, however, are not well understood and VOTFTs often require complex patterning techniques using self-assembly processes which impedes a future large-area production. In this contribution, high-performance vertical organic transistors comprising pentacene for p-type operation and C60 for n-type operation are presented. The static current-voltage behavior as well as the fundamental scaling laws of such transistors are studied, disclosing a remarkable transistor operation with a behavior limited by injection of charge carriers. The transistors are manufactured by photolithography, in contrast to other VOTFT concepts using self-assembled source electrodes. Fluorinated photoresist and solvent compounds allow for photolithographical patterning directly and strongly onto the organic materials, simplifying the fabrication protocol and making VOTFTs a prospective candidate for future high-performance applications of organic transistors. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Integración vertical y contratación externa en los servicios generales de los hospitales españoles Vertical integration and contracting-out in generic hospital services in Spain

Directory of Open Access Journals (Sweden)

J. Puig-Junoy

2002-04-01

Full Text Available Objetivos: Este estudio analiza los factores que influyen en las decisiones de integración vertical/contratación externa de cuatro servicios generales (limpieza, lavandería, alimentación y seguridad y mantenimiento en los hospitales españoles (3.160 transacciones que corresponden a 790 hospitales. Métodos: Se presenta la estimación empírica de un modelo logístico de maximización de la utilidad de los hospitales, en el que intervienen no sólo factores relacionados con los costes de transacción, sino también otros relacionados con la intervención pública y la dimensión política. Resultados: El 55,7% de los hospitales contrata al menos uno de los servicios generales analizados. El servicio de limpieza es el que presenta un mayor grado de contratación externa (45,1%, seguido del servicio de seguridad y mantenimiento (32,5%. En cambio, el servicio de lavandería es el que presenta un mayor grado de integración vertical (94,3% junto con el de alimentación (80,1%. La dimensión del hospital (economías de escala, medida a través del número de camas, es una de las variables que influyen de forma importante la decisión de integración vertical o contratación externa de los servicios de limpieza, alimentación y mantenimiento y seguridad. Conclusiones: Las economías de escala contribuyen a una mayor integración vertical, mientras que la especialización y el carácter lucrativo favorecen la decisión de contratación externa. El servicio de lavandería tiene un comportamiento diferenciado de los demás, mostrando efectos que indican la posible presencia de activos específicos.Objectives: This study examines the factors that influence make or buy decisions corresponding to four generic services (housekeeping, laundry, food services, and maintenance and security in Spanish hospitals (3,160 transactions in 790 hospitals. Methods: The empirical estimation of a logistic model based on hospital utility maximization is presented

Modelling vertical uniform contact stress of heavy vehicle tyres

CSIR Research Space (South Africa)

Steenkamp, Anton J

2016-07-01

Full Text Available over the selected operating range of 25 kN to 45 kN which is the typical load range for heavy vehicle tyres due to legal axle load limits. The polynomial formulas require only the tyre inflation pressure and vertical tyre load as inputs, in order...

A Partial Order on Bipartite Graphs with n Vertices

Directory of Open Access Journals (Sweden)

Emil Daniel Schwab

2009-01-01

Full Text Available The paper examines a partial order on bipartite graphs (X1, X2, E with n vertices, X1∪X2={1,2,…,n}. The basis of such bipartite graph is X1 = {1,2,…,k}, 0≤k≤n. If U = (X1, X2, E(U and V = (Y1,Y2, E(V then U≤V iff |X1| ≤ |Y1| and {(i,jE(U: j>|Y1|} = ={(i,jE(V:i≤|X1|}. This partial order is a natural partial order of subobjects of an object in a triangular category with bipartite graphs as morphisms.

Remote operation of the vertical plasma stabilization @ the GOLEM tokamak for the plasma physics education

Energy Technology Data Exchange (ETDEWEB)

Svoboda, V., E-mail: svoboda@fjfi.cvut.cz [Faculty of Nuclear Sciences and Physical Engineering CTU Prague, CZ-115 19 (Czech Republic); Kocman, J.; Grover, O. [Faculty of Nuclear Sciences and Physical Engineering CTU Prague, CZ-115 19 (Czech Republic); Krbec, J.; Stöckel, J. [Faculty of Nuclear Sciences and Physical Engineering CTU Prague, CZ-115 19 (Czech Republic); Institute of Plasma Physics AS CR, CZ-182 21 Prague (Czech Republic)

2015-10-15

Graphical abstract: * Understandable remote operation of a vertical plasma position control system in the tokamak GOLEM for educational purposes.* Two combinable modes of real-time plasma position control: position based feedback and a pre-defined waveform.* More than 20% plasma life prolongation with plasma position control in feedback mode. - Highlights: • Understandable remote operation of a vertical plasma position control system in the tokamak GOLEM for educational purposes. • Two combinable modes of real-time plasma position control: position based feedback and a pre-defined waveform. • More than 20% plasma life prolongation with plasma position control in feedback mode. - Abstract: The GOLEM tokamak at the Czech Technical University has been established as an educational tokamak device for domestic and foreign students. Remote participation in the scope of several laboratory practices, plasma physics schools and workshops has been successfully performed from abroad. A new enhancement allowing understandable remote control of vertical plasma position in two modes (i) predefined and (ii) feedback control is presented. It allows to drive the current in the stabilization coils in any time-dependent scenario, which can include as a parameter the actual plasma position measured by magnetic diagnostics. Arbitrary movement of the plasma column in a vertical direction, stabilization of the plasma column in the center of the tokamak vessel as well as prolongation/shortening of plasma life according to the remotely defined request are demonstrated.

Anovulación y disfunción ovulatoria e infertilidad

Directory of Open Access Journals (Sweden)

N. Amiram Magendzo, Dr.

2010-05-01

El objetivo principal en la evaluación de estas pacientes es identificar la causa que está provocando la anovulación crónica. Para propósitos de esta revisión, las causas potenciales se han agrupado en: a amenorreas hipotalámicas, b Anovulación crónica funcional, c Síndrome de ovario poliquístico, d hiperprolactinemia, e Disfunción tiroídea, f Falla ovárica prematura. El tratamiento está enfocado en corregir la condición que pueda estar causando el problema, optimizar la calidad de vida de la paciente y su salud, y reestablecer ciclos normales o inducir la ovulación si es que fuera necesario. Respecto a este último punto, los diferentes medicamentos y protocolos más comúnmente usados para inducción de la ovulación se analizan en detalle.

Optimization of operating parameters of hybrid vertical down-flow constructed wetland systems for domestic sewerage treatment.

Science.gov (United States)

Huang, Zhujian; Zhang, Xianning; Cui, Lihua; Yu, Guangwei

2016-09-15

In this work, three hybrid vertical down-flow constructed wetland (HVDF-CW) systems with different compound substrates were fed with domestic sewage and their pollutants removal performance under different hydraulic loading and step-feeding ratio was investigated. The results showed that the hydraulic loading and step-feeding ratio were two crucial factors determining the removal efficiency of most pollutants, while substrate types only significantly affected the removal of COD and NH4(+)-N. Generally, the lower the hydraulic loading, the better removal efficiency of all contaminants, except for TN. By contrast, the increase of step-feeding ratio would slightly reduce the removal rate of ammonium and TP but obviously promoted the TN removal. Therefore, the optimal operation of this CWs could be achieved with low hydraulic loading combined with 50% of step-feeding ratio when TN removal is the priority, whereas medium or low hydraulic loading without step-feeding would be suitable when TN removal is not taken into consideration. The obtained results in this study can provide us with a guideline for design and optimization of hybrid vertical flow constructed wetland systems to improve the pollutants removal from domestic sewage. Copyright © 2016 Elsevier Ltd. All rights reserved.

The SU(2 vertical stroke 3) spin chain sigma model

International Nuclear Information System (INIS)

Hernandez, R.; Lopez, E.

2005-01-01

The one-loop planar dilatation operator of N = 4 supersymmetric Yang-Mills is isomorphic to the hamiltonian of an integrable PSU(2,2 vertical stroke 4) spin chain. We construct the non-linear sigma model describing the continuum limit of the SU(2 vertical stroke 3) subsector of the N = 4 chain. We explicitly identify the spin chain sigma model with the one for a superstring moving in AdS 5 x S 5 with large angular momentum along the five-sphere. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

Higher dimensional operator corrections to the goldstino Goldberger-Treiman vertices

International Nuclear Information System (INIS)

Lee, T.

2000-01-01

The goldstino-matter interactions given by the Goldberger-Treiman relations can receive higher dimensional operator corrections of O(q 2 /M 2 ), where M denotes the mass of the mediators through which SUSY breaking is transmitted. These corrections in the gauge mediated SUSY breaking models arise from loop diagrams, and an explicit calculation of such corrections is presented. It is emphasized that the Goldberger-Treiman vertices are valid only below the mediator scale, and at higher energies goldstinos decouple from the MSSM fields. The implication of this fact for gravitino cosmology in GMSB models is mentioned. (orig.)

Simulation of electrical characteristics of GaN vertical Schottky diodes

Science.gov (United States)

Łukasiak, Lidia; Jasiński, Jakub; Jakubowski, Andrzej

2016-12-01

Reverse current of GaN vertical Schottky diodes is simulated using Silvaco ATLAS to optimize the geometry for the best performance. Several physical quantities and phenomena, such as carrier mobility and tunneling mechanism are studied to select the most realistic models. Breakdown voltage is qualitatively estimated based on the maximum electric field in the structure.

Relación entre la fuerza máxima en squat y acciones de salto, sprint y golpeo de balón. (Relationship among maximal strength in squat exercise, jump, sprint and kicking ball performance.

Directory of Open Access Journals (Sweden)

Alfredo Arija Blázquez

2008-01-01

Full Text Available ResumenEl objetivo del presente estudio fue analizar las posibles relaciones entre la fuerza máxima en squat y accionesexplosivas de salto, sprint y golpeo de balón. Para ello, se contó con una muestra formada por estudiantes de Ciencias del Deporte (N= 16; 19,6 ± 1,7 años de sexo masculino (con escasa experiencia en el entrenamiento de fuerza, que llevaron a cabo un test de 1RM en squat (calculándose el peso levantado, la fuerza media total y la fuerza dinámica máxima, tests de salto vertical (SJ, CMJ y CMJa, un test de sprint de 20 m (con mediciones de tiempo cada 5 m, y un test de golpeo con el pie donde se calculaba la velocidad del balón. Se encontraron coeficientes de correlación moderados (entre 0,52 y 0,67 y significativos de las medidas de fuerza máxima y las alturas de salto, mientras que los coeficientes obtenidos entre los tiempos de sprint y dichas medidas de fuerza máxima se situaron entre -0,06 y -0,32, no siendo ninguno de ellos significativo; al igual que tampoco fueron significativos los coeficientes de correlación de las medidas de fuerza máxima y la velocidad de tiro, se situaron entre 0,25 y 0,34. Por tanto, la relación entre la fuerza máxima en squat y la altura de salto en sujetos con escasa experiencia en el entrenamiento de fuerza resultó moderada, mientras que no parece existir relación con el tiempo de sprint y la velocidad de tiro.AbstractThe purpose of the present study was to analyze the possible relationships between maximal strength insquat exercise and jump, sprint and kicking ball actions. Sixteen males sport science students (19,6 ± 1,7years, with little experience in strength training, performed a 1RM in squat exercise (from which liftedweight, the total average- and maximal-dynamic strength was assessed, vertical jump (SJ, CMJ and CMJa, a 20 m sprint test (with time measurement every 5 m, and a kicking ball test where the velocity of the ball was calculated. Moderate (0,52 - 0,67 and

Description of work vadose drilling at the 1301-N and 1325-N facilities, 100-NR-1 operable unit

International Nuclear Information System (INIS)

1994-08-01

This description of work (DOW) details the field activities associated with the sampling of the vadose zone soils beneath the 1301-N and 1325-N cribs and trenches and will serve as a field guide for those performing the work. These activities are undertaken pursuant to the Hanford Federal Facility Agreement and Consent Order (Ecology et al., 1994a) Milestone M-16-94-01H-Tl and the June 30, 1994 Milestone Change Request M-16-94-02 (Ecology et al., 1994b). Three vadose zone borings, 1301-N-1, 1301-N-2, and 1325-N-1, will be constructed to investigate the vertical and horizontal distribution of radionuclide contamination in sediments beneath the cribs and trenches. The boreholes are also intended to intersect subsurface areas that may have been contaminated by dangerous wastes, i.e., metals, in effluent disposed during past operation of the facilities. This limited field investigation will provide data for the evaluation of remedial alternatives. Data from the investigation are expected to confirm that the cribs and trenches are high priority sites in the 100-NR-1 operable unit. Data, from the investigation will be used to evaluate alternatives for closure of the 1301-N and 1325-N sites. The contaminants of potential concern (COPCs) for the 1301-N/1325-N limited field investigation are presented in Table 1

Evaluation of some geophysical events on 22 September 1979

International Nuclear Information System (INIS)

Hones, E.W. Jr.; Baker, D.N.; Feldman, W.C.

1981-04-01

TIROS-N plasma data and related geophysical data measured on 22 September 1979 were analyzed to determine whether the electron precipitation event detected by TIROS-N at 00:54:49 universal time could have been related to a surface nuclear burst (SNB). The occurrence of such a burst was inferred from light signals detected by two Vela bhangmeters approx. 2 min before the TIROS-N event. The precipitation was found to be unusually large but not unique. It probably resulted from passage of TIROS-N through The precipitating electrons above a pre-existing auroral arc that may have brightened to an unusually high intensity from natural causes approx. 3 min before the Vela signals. On the othe hand, no data were found that were inconsistent with the SNB interpretation of the 22 September Vela observations. In fact, a patch of auroral light that suddenly appeared in the sky near Syowa Base, Antarctica a few seconds after the Vela event can be interpreted (though not uniquely) as a consequence of the electromagnetic pulse of an SNB

Transmissão vertical do HIV: situação encontrada em uma maternidade de Teresina Transmisión vertical del HIV: situación encontrada en una maternidade de Teresina Vertical transmission of HIV: situation found in a maternity of Teresina

Directory of Open Access Journals (Sweden)

Liliam Mendes de Araújo

2007-08-01

Full Text Available Oaumento dos casos de AIDS em mulheres evidencia um progressivo aumento da transmissão vertical do HIV, no Brasil e no Piauí. Considerando a relevância do tema o presente estudo teve como objetivo analisar as condições da implementação das normas e medidas recomendadas pelo Ministério da Saúde para prevenir a transmissão vertical do HIV em uma maternidade de Teresina - PI. O caminho teórico-metodológico compreendeu o estudo da dinâmica organizacional e dos seus atores, por meio de abordagem qualitativa. Para obtenção dos dados foram realizadas 17 entrevistas semi-estruturadas. Os resultados mostraram que as recomendações do Ministério da Saúde não foram atendidas na sua totalidade evidenciando a precariedade da assistência prestada para o binômio mãe/filho.El aumento de los casos de AIDS en mujeres, evidencia un progresivo aumento de la transmisión vertical de lo HIV en el Brasil, e en el Piauí. Considerando la relevancia del tema, el presente estudio tuve como objetivo analizar las condiciones de la implementación de las reglas y medidas recomendadas por el Ministerio de la Salud para prevenir la transmisión vertical del HIV en una maternidad de Teresina-PI. El camino teórico-metodológico comprendió el estudio de la dinámica organizacional y de sus actores, a través del abordaje cualitativa.. Para la obtención de los datos fueran realizados 17 entrevistas medio-estructuradas. Los resultados mostraran que las recomendaciones del Ministerio de la Salud non fueran atendidas en la suya totalidad, evidenciando la precariedad de la asistencia prestada, para el binomio madre / hijo.The increase of the number of cases of AIDS among women reveals a progressive increase of the vertical transmission of HIV in Brazil, as well as in Piauí. Considering the relevance of the subject, this study had as objective to analyze the conditions of the implementation of the rules and measures recommended by the Ministry of Health to

Características metabólicas del músculoGluteus medius de equinos mestizos con aptitud de tiro Metabolic characteristics of the Gluteus medius musclein crossbreed draft horses

OpenAIRE

V. MERINO; A. ISLAS; J. LOPEZ-RIVERO; G. MORA; M. QUEZADA; J. LOPEZ; J. REYES

1998-01-01

De 16 equinos mestizos de tiro, de ambos sexos, clínicamente sanos, se obtuvieron biopsias del músculo Gluteus medius a 3, 6 y 9 cm de profundidad, con el objetivo de evaluar su metabolismo anaeróbico y aeróbico, determinando las actividades de las enzimas creatinquinasa (CK), deshidrogenasa láctica (LDH) y citrato sintetasa (CS) en animales inactivos y trabajando en faenas agrícolas. El tejido muscular se homogeneizó, sonicó y centrifugó; posteriormente en el sobrenadante se determinaron las...

Diferencias de los indicadores de rendimiento en baloncesto femenino entre ganadores y perdedores en función de jugar como local o como visitante

Directory of Open Access Journals (Sweden)

Miguel \\u00C1ngel G\\u00F3mez Ruano

2007-01-01

presentan unos porcentajes de eficacia en el lanzamiento de 2 puntos (49%, 3 puntos (38% y tiros libres (70%, muy superiores a los perdedores. Estos valores deberán servir de referencia a los entrenadores para diseñar ejercicios en los entrenamientos, y a los psicólogos deportivos para diseñar programas de intervención.

Prevención de la transmisión vertical del VIH-1 en un hospital público de complejidad terciaria de Buenos Aires, Argentina Prevention of vertical HIV-1 transmission in a tertiary care public hospital in Buenos Aires, Argentina

Directory of Open Access Journals (Sweden)

Diego Cecchini

2011-09-01

Full Text Available OBJETIVO: Describir las características de los binomios madre-hijo, la profilaxis antirretroviral, la evolución temporal de la transmisión vertical del VIH-1 y sus variables asociadas en una población asistida por un hospital público de complejidad terciaria de Argentina. MÉTODOS: Estudio descriptivo prospectivo desarrollado por el Grupo de trabajo en prevención de la Transmisión Vertical del Hospital General de Agudos Dr. Cosme Argerich, Buenos Aires, Argentina, entre 1998 y 2008. Se compararon los períodos 1998-2003 y 2004-2008, y se identificaron las variables asociadas a esta vía de contagio. RESULTADOS: De 357 binomios madre-hijo, 21,0% de las madres presentaron coinfección con el virus de la hepatitis C y 68,0% linfocitos CD4 OBJECTIVE: To describe characteristics of mother-child binomium (MCB, antiretroviral (ARV prophylaxis, time trends, and variables associated with vertical transmission of HIV-1 in a population assisted by a tertiary public hospital in Argentina. METHODS: Prospective descriptive study undertaken by the Hospital Cosme Argerich s Vertical Transmission Working Group, Buenos Aires city, Argentina 1998-2008. Periods 1998-2003 vs. 2004-2008 were compared and variables associated with vertical transmission identified. RESULTS: Of 357 MCB, 21.0% of the mothers had HCV coinfection and 68.0% CD4 < 500/µL. During pregnancy, 75.0% received ARV: zidovudine (17.8%, zidovudinelamivudine (19.8%, zidovudine-lamivudine-nevirapine (41.9%, and zidovudinelamivudine-protease inhibitor (11.4%; 74.0% had viral load (VL peripartum < 1 000 copies/mL. Caesarean delivery: 58.0%. Intrapartum zidovudine: 83.4%; 98.0% of infants received prophylaxis; zidovudine monotherapy was the most frequently used (73.0%. Of neonates, 15.4% had low birthweight and 6.7% were premature. The global vertical transmission was 3.3% (10/302. Comparing both periods, an increase in triple ARV and VL < 1 000 copies/mL in peripartum and a decrease in the

Laser-induced local activation of Mg-doped GaN with a high lateral resolution for high power vertical devices

Science.gov (United States)

Kurose, Noriko; Matsumoto, Kota; Yamada, Fumihiko; Roffi, Teuku Muhammad; Kamiya, Itaru; Iwata, Naotaka; Aoyagi, Yoshinobu

2018-01-01

A method for laser-induced local p-type activation of an as-grown Mg-doped GaN sample with a high lateral resolution is developed for realizing high power vertical devices for the first time. As-grown Mg-doped GaN is converted to p-type GaN in a confined local area. The transition from an insulating to a p-type area is realized to take place within about 1-2 μm fine resolution. The results show that the technique can be applied in fabricating the devices such as vertical field effect transistors, vertical bipolar transistors and vertical Schottkey diode so on with a current confinement region using a p-type carrier-blocking layer formed by this technique.

Negative differential resistance observed from vertical p+-n+ junction device with two-dimensional black phosphorous

Science.gov (United States)

Lee, Daeyeong; Jang, Young Dae; Kweon, Jaehwan; Ryu, Jungjin; Hwang, Euyheon; Yoo, Won Jong; Samsung-SKKU Graphene/2D Center (SSGC) Collaboration

A vertical p+-n+ homojunction was fabricated by using black phosphorus (BP) as a van der Waals two-dimensional (2D) material. The top and bottom layers of the materials were doped by chemical dopants of gold chloride (AuCl3) for p-type doping and benzyl viologen (BV) for n-type doping. The negative differential resistance (NDR) effect was clearly observed from the output curves of the fabricated BP vertical devices. The thickness range of the 2D material showing NDR and the peak to valley current ratio of NDR are found to be strongly dependent on doping condition, gate voltage, and BP's degradation level. Furthermore, the carrier transport of the p+-n+ junction was simulated by using density functional theory (DFT) and non-equilibrium Green's function (NEGF). Both the experimental and simulation results confirmed that the NDR is attributed to the band-to-band tunneling (BTBT) across the 2D BP p+-n+ junction, and further quantitative details on the carrier transport in the vertical p+-n+ junction devices were explored, according to the analyses of the measured transfer curves and the DFT simulation results. This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MEST) (2013R1A2A2A01015516).

Spatial identification of traps in AlGaN/GaN heterostructures by the combination of lateral and vertical electrical stress measurements

International Nuclear Information System (INIS)

Hu, Anqi; Yang, Xuelin; Cheng, Jianpeng; Guo, Lei; Zhang, Jie; Ge, Weikun; Xu, Fujun; Tang, Ning; Qin, Zhixin; Wang, Maojun; Wang, Xinqiang; Shen, Bo

2016-01-01

We present a methodology and the corresponding experimental results to identify the exact location of the traps that induce hot electron trapping in AlGaN/GaN heterostructures grown on Si substrates. The methodology is based on a combination of lateral and vertical electrical stress measurements employing three ohmic terminals on the test sample structure with different GaN buffer designs. By monitoring the evolution of the lateral current during lateral as well as vertical stress application, we investigate the trapping/detrapping behaviors of the hot electrons and identify that the traps correlated with current degradation are in fact located in the GaN buffer layers. The trap activation energies (0.38–0.39 eV and 0.57–0.59 eV) extracted from either lateral or vertical stress measurements are in good agreement with each other, also confirming the identification. By further comparing the trapping behaviors in two samples with different growth conditions of an unintentionally doped GaN layer, we conclude that the traps are most likely in the unintentionally doped GaN layer but of different origins. It is suggested that the 0.38–0.39 eV trap is related to residual carbon incorporation while the 0.57–0.59 eV trap is correlated with native defects or complexes

The complete vertical stroke ΔS vertical stroke =2-hamiltonian in the next-to-leading order

International Nuclear Information System (INIS)

Herrlich, S.; Nierste, U.

1996-04-01

We present the complete next-to-leading order short-distance QCD corrections to the effective vertical stroke ΔS vertical stroke =2-hamiltonian in the Standard Model. The calculation of the coefficient η 3 is described in great detail. It involves the two-loop mixing of bilocal structures composed of two vertical stroke ΔS vertical stroke =1 operators into vertical stroke ΔS vertical stroke =2 operators. The next-to-leading order corrections enhance η 3 by 27% to η 3 =0.47(+0.03-0.04) thereby affecting the phenomenology of ε K sizeably. η 3 depends on the physical input parameters m t , m c and Λsub(anti M anti S) only weakly. The quoted error stems from renormalization scale dependences, which have reduced compared to the old leading log result. The known calculation of η 1 and η 2 is repeated in order to compare the structure of the three QCD coefficients. We further discuss some field theoretical aspects of the calculation such as the renormalization group equation for Green's functions with two operator insertions and the renormalization scheme dependence caused by the presence of evanescent operators. (orig.)

Integración vertical y contratos gerenciales: herramientas estratégicas en mercados imperfectos

Directory of Open Access Journals (Sweden)

Flavio Jácome Liévano

2014-12-01

Full Text Available Este artículo analiza un modelo de competencia a la Bertrand con bienes diferenciados, que permite determinar las decisiones óptimas de las empresas cuando los dueños pueden usar la integración vertical y los contratos gerenciales como herramientas estratégicas. En equilibrio se obtiene que: i los dueños siempre delegan el control en un gerente y este es incentivado a ser menos agresivo en ventas; ii cuando los bienes son casi homogéneos, no hay integración vertical; iii el bienestar social en ningún caso es el más alto que se podría lograr.

Evaluación de la dimensión vertical de oclusión, perfil blando y maloclusión en dentición mixta

Directory of Open Access Journals (Sweden)

María Laura Hermida Bruno

2016-01-01

Full Text Available Objetivo: Verificar la relación entre dimensión vertical de oclusión, perfil blando y maloclusión en dentición mixta. Métodos: Se realizó un estudio observacional, transversal, analítico. El protocolo fue aprobado por el Comité de Ética de la Universidad Católica del Uruguay. Participaron 79 niños entre 6 y 12 años, con una media de edad de 8,66 ±1,41, alumnos del Colegio San José del Cerro, Montevideo, Uruguay. El 57,5% (n=45 correspondió al sexo masculino y 42,5% (n=34 al sexo femenino. Un observador calibrado (CCI=0,76 realizó un examen clínico y físico, medición de la dimensión vertical de oclusión (DVO y registró la clasificación de Angle. Se tomaron fotografías de perfil y se realizó el análisis de convexidad facial de Legan y Burstone (CCI=0,84. Se aplicó el test comparativo ANOVA, el de comparaciones múltiples de TUKEY y el test de Pearson (p ≤ 0,05. Resultados: La media de la DVO fue 59,16 ± 4,02. El 56,3% (n=45 fueron clasificados como Clase I de Angle; 22,5% (n=18 Clase II y 21,3% (n=17 Clase III. No hubo diferencia significativa en la media de DVO entre ambos sexos (p=0,217 ni entre los diferentes tipos de oclusión (p=0,568. La media del ángulo de la convexidad facial fue 14,57°± 3,80. Se encontró asociación estadísticamente significativa entre perfil convexo/relación molar clase II (p=0,003317, perfil recto/relación molar clase I (p=0,015887, perfil recto/relación molar clase III (p=0,003268. Conclusión: En la muestra estudiada no se encontró relación entre DVO y maloclusión, pero sí se encontró entre perfil blando y maloclusión.

Growth of vertically oriented InN nanorods from In-rich conditions on unintentionally patterned sapphire substrates

Energy Technology Data Exchange (ETDEWEB)

Terziyska, Penka T., E-mail: pterziy1@lakeheadu.ca [Semiconductor Research Laboratory, Department of Electrical Engineering, Lakehead University, 955 Oliver Road, Thunder Bay, ON P7B 5E1 (Canada); Butcher, Kenneth Scott A. [Semiconductor Research Laboratory, Department of Electrical Engineering, Lakehead University, 955 Oliver Road, Thunder Bay, ON P7B 5E1 (Canada); MEAglow Ltd., Box 398, 2400 Nipigon Road, Thunder Bay, ON P7C4W1 (Canada); Rafailov, Peter [Institute of Solid State Physics, Bulgarian Academy of Sciences, 72 Tzarigradsko Chaussee Blvd., 1784 Sofia (Bulgaria); Alexandrov, Dimiter [Semiconductor Research Laboratory, Department of Electrical Engineering, Lakehead University, 955 Oliver Road, Thunder Bay, ON P7B 5E1 (Canada); MEAglow Ltd., Box 398, 2400 Nipigon Road, Thunder Bay, ON P7C4W1 (Canada)

2015-10-30

Highlights: • Vertical InN nanorods are grown on selective areas of sapphire substrates. • In metal droplets nucleate on the sharp needle apexes on the selective areas. • The preferred orientation and the growth direction of the nanorods are (0 0 0 1). • The nanorods grow from the supersaturated indium melt on their tops. - Abstract: Vertically oriented InN nanorods were grown on selective areas of unintentionally patterned c-oriented sapphire substrates exhibiting sharp needles that preferentially accommodate In-metal liquid droplets, using Migration Enhanced Afterglow (MEAglow) growth technique. We point out that the formation of AlN needles on selected areas can be reproduced intentionally by over-nitridation of unmasked areas of sapphire substrates. The liquid indium droplets serve as a self-catalyst and the nanorods grow from the supersaturated indium melt in the droplet in a vertical direction. X-ray diffraction measurements indicate the presence of hexagonal InN only, with preferred orientation along (0 0 0 1) crystal axis, and very good crystalline quality. The room temperature Raman spectrum shows the presence of the A{sub 1}(TO), E{sub 2}(high) and A{sub 1}(LO) phonon modes of the hexagonal InN.

Fabrication and Characterization of Vertical Gallium Nitride Power Schottky Diodes on Bulk GaN Substrates FY2016

Science.gov (United States)

2016-12-01

ARL-TR-7913 ● DEC 2016 US Army Research Laboratory Fabrication and Characterization of Vertical Gallium Nitride Power Schottky...TR-7913 ● DEC 2016 US Army Research Laboratory Fabrication and Characterization of Vertical Gallium Nitride Power Schottky Diodes on Bulk...Fabrication and Characterization of Vertical Gallium Nitride Power Schottky Diodes on Bulk GaN Substrates FY2016 5a. CONTRACT NUMBER 5b. GRANT NUMBER

Operational State Complexity of Deterministic Unranked Tree Automata

Directory of Open Access Journals (Sweden)

Xiaoxue Piao

2010-08-01

Full Text Available We consider the state complexity of basic operations on tree languages recognized by deterministic unranked tree automata. For the operations of union and intersection the upper and lower bounds of both weakly and strongly deterministic tree automata are obtained. For tree concatenation we establish a tight upper bound that is of a different order than the known state complexity of concatenation of regular string languages. We show that (n+1 ( (m+12^n-2^(n-1 -1 vertical states are sufficient, and necessary in the worst case, to recognize the concatenation of tree languages recognized by (strongly or weakly deterministic automata with, respectively, m and n vertical states.

VIH: Transmisión Vertical y Síndrome Neurológico en Infantes

OpenAIRE

Jean Paul Astrulla Santa Cruz; Boris A. Blanco Cáceres; Dr. Carlos Eróstegui Revilla

2009-01-01

La epidemia del VIH/SIDA dejó de ser una enfermedad exclusivamente de homosexuales, para convertirse enuna enfermedad que ataca al ser humano sin distinción de raza, sexo o edad. El sexo femenino está cada vez másexpuesto a la infección y es capaz de transmitir el VIH a su hijo si no hay una intervención terapéutica adecuadaen el período de gestación. Se han descrito tres tiempos en los cuales la transmisión vertical puede ocurrir: transmisiónintraútero, transmisión intraparto, transmisión po...

Oxygen profile and clogging in vertical flow sand filters for on-site wastewater treatment.

Science.gov (United States)

Petitjean, A; Forquet, N; Boutin, C

2016-04-01

13 million people (about 20% of the population) use on-site wastewater treatment in France. Buried vertical sand filters are often built, especially when the soil permeability is not sufficient for septic tank effluent infiltration in undisturbed soil. Clogging is one of the main problems deteriorating the operation of vertical flow filters for wastewater treatment. The extent of clogging is not easily assessed, especially in buried vertical flow sand filters. We suggest examining two possible ways of detecting early clogging: (1) NH4-N/NO3-N outlet concentration ratio, and (2) oxygen measurement within the porous media. Two pilot-scale filters were equipped with probes for oxygen concentration measurements and samples were taken at different depths for pollutant characterization. Influent and effluent grab-samples were taken three times a week. The systems were operated using batch-feeding of septic tank effluent. Qualitative description of oxygen transfer processes under unclogged and clogged conditions is presented. NH4-N outlet concentration appears to be useless for early clogging detection. However, NO3-N outlet concentration and oxygen content allows us to diagnose the early clogging of the system. Copyright © 2016 Elsevier Ltd. All rights reserved.

Vertical market participation

DEFF Research Database (Denmark)

Schrader, Alexander; Martin, Stephen

1998-01-01

Firms that operate at both levels of vertically related Cournot oligopolies will purchase some input supplies from independent rivals, even though they can produce the good at a lower cost, driving up input price for nonintegrated firms at the final good level. Foreclosure, which avoids this stra......Firms that operate at both levels of vertically related Cournot oligopolies will purchase some input supplies from independent rivals, even though they can produce the good at a lower cost, driving up input price for nonintegrated firms at the final good level. Foreclosure, which avoids...

Test reports for K Basins vertical fuel handling tools

Energy Technology Data Exchange (ETDEWEB)

Meling, T.A.

1995-02-01

The vertical fuel handling tools, for moving N Reactor fuel elements, were tested in the 305 Building Cold Test Facility (CTF) in the 300 Area. After fabrication was complete, the tools were functionally tested in the CTF using simulated N Reactor fuel rods (inner and outer elements). The tools were successful in picking up the simulated N Reactor fuel rods. These tools were also load tested using a 62 pound dummy to test the structural integrity of each assembly. The tools passed each of these tests, based on the performance objectives. Finally, the tools were subjected to an operations acceptance test where K Basins Operations personnel operated the tool to determine its durability and usefulness. Operations personnel were satisfied with the tools. Identified open items included the absence of a float during testing, and documentation required prior to actual use of the tools in the 100 K fuel storage basin.

High-voltage vertical GaN Schottky diode enabled by low-carbon metal-organic chemical vapor deposition growth

Science.gov (United States)

Cao, Y.; Chu, R.; Li, R.; Chen, M.; Chang, R.; Hughes, B.

2016-02-01

Vertical GaN Schottky barrier diode (SBD) structures were grown by metal-organic chemical vapor deposition on free-standing GaN substrates. The carbon doping effect on SBD performance was studied by adjusting the growth conditions and spanning the carbon doping concentration between ≤3 × 1015 cm-3 and 3 × 1019 cm-3. Using the optimized growth conditions that resulted in the lowest carbon incorporation, a vertical GaN SBD with a 6-μm drift layer was fabricated. A low turn-on voltage of 0.77 V with a breakdown voltage over 800 V was obtained from the device.

Evaluación de la transmisión vertical de Bartonella bacilliformis en Lutzomyia verrucarum (Diptera: Psychodidae

Directory of Open Access Journals (Sweden)

Carlos Ponce G

2002-04-01

Full Text Available Objetivos: Identificar la existencia de transmisión vertical de Bartonella bacilliformis en Lutzomyia verrucarum. Materiales y métodos: en este estudio experimental, se realizó la crianza individual y masiva (Tº 22°C±2ºC, humedad relativa: 80%±5% de Lutzomyia verrucarum en el Laboratorio de Entomología del Centro de Investigaciones del Hospital de Caraz (Ancash- Perú. Con la finalidad de lograr la infección de las hembras se procedió a alimentarlas con sangre infectada obtenida por éstas directamente al picar la piel de pacientes con bartonelosis aguda frotis positivo. Las hembras, luego de poner sus huevos, fueron evaluadas a través de la prueba de PCR para Bartonella baciliformis. Resultados: 13 de 18 (72,2% hembras alimentadas con sangre infectada con bacteremia al 3% lograron poner huevos y de éstas ninguna resultó ser positiva al PCR. 12 de 54 (22,2% hembras alimentadas con sangre infectada con bacteremia al 80% ovipusieron y de éstas sólo una (8,3% resultó ser positiva al PCR. Ninguno de los descendientes adultos de esta hembra resultó positivo al PCR. Conclusiones: el bajo porcentaje de infección por Bartonella baciliformis encontrado en hembras oviponedoras no permitió determinar la existencia de transmisión vertical de Bartonella bacilliformis en Lutzomyia verrucarum.

De la empresa al mercado: la desintegración vertical del transporte terrestre en España

Directory of Open Access Journals (Sweden)

Compés López, Raúl

2005-12-01

Full Text Available Las empresas españolas recurren cada vez más a la subcontratación del servicio de transporte terrestre. Este modelo es el resultado de un proceso de desintegración vertical que lleva a vender los vehículos y a reubicar a los trabajadores dentro o fuera de la empresa. Las reformas del marco institucional que regula la prestación de este servicio, y las normas fiscales, contractuales y sociales que afectan los costos y beneficios de la prestación del servicio inciden de manera diferente en los distintos tipos de empresas. La desintegración vertical genera costos de salida que afectan al ritmo, la estrategia y el resultado del cambio del modelo organizativo.

Nucleation, Growth Mechanism, and Controlled Coating of ZnO ALD onto Vertically Aligned N-Doped CNTs.

Science.gov (United States)

Silva, R M; Ferro, M C; Araujo, J R; Achete, C A; Clavel, G; Silva, R F; Pinna, N

2016-07-19

Zinc oxide thin films were deposited on vertically aligned nitrogen-doped carbon nanotubes (N-CNTs) by atomic layer deposition (ALD) from diethylzinc and water. The study demonstrates that doping CNTs with nitrogen is an effective approach for the "activation" of the CNTs surface for the ALD of metal oxides. Conformal ZnO coatings are already obtained after 50 ALD cycles, whereas at lower ALD cycles an island growth mode is observed. Moreover, the process allows for a uniform growth from the top to the bottom of the vertically aligned N-CNT arrays. X-ray photoelectron spectroscopy demonstrates that ZnO nucleation takes place at the N-containing species on the surface of the CNTs by the formation of the Zn-N bonds at the interface between the CNTs and the ZnO film.

Analysis of vertical stability limits and vertical displacement event behavior on NSTX-U

Science.gov (United States)

Boyer, Mark; Battaglia, Devon; Gerhardt, Stefan; Menard, Jonathan; Mueller, Dennis; Myers, Clayton; Sabbagh, Steven; Smith, David

2017-10-01

The National Spherical Torus Experiment Upgrade (NSTX-U) completed its first run campaign in 2016, including commissioning a larger center-stack and three new tangentially aimed neutral beam sources. NSTX-U operates at increased aspect ratio due to the larger center-stack, making vertical stabilization more challenging. Since ST performance is improved at high elongation, improvements to the vertical control system were made, including use of multiple up-down-symmetric flux loop pairs for real-time estimation, and filtering to remove noise. Similar operating limits to those on NSTX (in terms of elongation and internal inductance) were achieved, now at higher aspect ratio. To better understand the observed limits and project to future operating points, a database of vertical displacement events and vertical oscillations observed during the plasma current ramp-up on NSTX/NSTX-U has been generated. Shots were clustered based on the characteristics of the VDEs/oscillations, and the plasma parameter regimes associated with the classes of behavior were studied. Results provide guidance for scenario development during ramp-up to avoid large oscillations at the time of diverting, and provide the means to assess stability of target scenarios for the next campaign. Results will also guide plans for improvements to the vertical control system. Work supported by U.S. D.O.E. Contract No. DE-AC02-09CH11466.

Initial leakage current paths in the vertical-type GaN-on-GaN Schottky barrier diodes

Science.gov (United States)

Sang, Liwen; Ren, Bing; Sumiya, Masatomo; Liao, Meiyong; Koide, Yasuo; Tanaka, Atsushi; Cho, Yujin; Harada, Yoshitomo; Nabatame, Toshihide; Sekiguchi, Takashi; Usami, Shigeyoshi; Honda, Yoshio; Amano, Hiroshi

2017-09-01

Electrical characteristics of leakage current paths in vertical-type n-GaN Schottky barrier diodes (SBDs) on free-standing GaN substrates are investigated by using photon emission microscopy (PEM). The PEM mapping shows that the initial failure of the SBD devices at low voltages is due to the leakage current paths from polygonal pits in the GaN epilayers. It is observed that these polygonal pits originate from carbon impurity accumulation to the dislocations with a screw-type component by microstructure analysis. For the SBD without polygonal pits, no initial failure is observed and the first leakage appeals at the edge of electrodes as a result of electric field concentration. The mechanism of leakage at pits is explained in terms of trap assisted tunneling through fitting current-voltage characteristics.

5.0 kV breakdown-voltage vertical GaN p-n junction diodes

Science.gov (United States)

Ohta, Hiroshi; Hayashi, Kentaro; Horikiri, Fumimasa; Yoshino, Michitaka; Nakamura, Tohru; Mishima, Tomoyoshi

2018-04-01

A high breakdown voltage of 5.0 kV has been achieved for the first time in vertical GaN p-n junction diodes by using our newly developed guard-ring structures. A resistance device was inserted between the main diode portion and the guard-ring portion in a ring-shaped p-n diode to generate a voltage drop over the resistance device by leakage current flowing through the guard-ring portion under negatively biased conditions before breakdown. The voltage at the outer mesa edge of the guard-ring portion, where the electric field intensity is highest and the destructive breakdown usually occurs, is decreased by the voltage drop, so the electric field concentration in the portion is reduced. By adopting this structure, the breakdown voltage (V B) is raised by about 200 V. Combined with a low measured on-resistance (R on) of 1.25 mΩ cm2, Baliga’s figure of merit (V\\text{B}2/R\\text{on}) was as high as 20 GW/cm2.

Characteristic features of silicon multijunction solar cells with vertical p-n junctions

International Nuclear Information System (INIS)

Guk, E.G.; Nalet, T.A.; Shvarts, M.Z.; Shuman, V.B.

1997-01-01

A relatively simple technology (without photolithography) based on diffusion welding and ion-plasma deposition of an insulating coating has been developed for fabricating multijunction silicon solar cells with vertical p-n junctions. The effective collection factor for such structures is independent of the wavelength of the incident light in the wavelength range λ=340-1080 nm

VIH/SIDA: COMPORTAMIENTO EPIDEMIOLÓGICO DE LA TRANSMISIÓN VERTICAL EN EL CONTEXTO GENERAL DE LA INFECCIÓN EN CHILE

OpenAIRE

Valdés R,Enrique; Sepúlveda M,Alvaro; Candia P,Paula; Sepúlveda B,Carolina; Lattes A,Karinna

2011-01-01

Antecedentes: En embarazadas seropositivas sin profilaxis antirretroviral la transmisión vertical (TV) del VIH es de 30%, cifra que disminuye bajo al 2% con un manejo integral de prevención. Objetivo: Conocer el comportamiento epidemiológico de la TV en Chile desde la creación del programa nacional de prevención. Método: Datos aportados por el Departamento de Epidemiología del MINSAL y CONASIDA (1984-2006). Estudió de situación VIH/SIDA por año, regiones, grupo etario y sexo, con especial énf...

4.5 μm wavelength vertical external cavity surface emitting laser operating above room temperature

Science.gov (United States)

Rahim, M.; Khiar, A.; Felder, F.; Fill, M.; Zogg, H.

2009-05-01

A midinfrared vertical external cavity surface emitting laser with 4.5 μm emission wavelength and operating above room temperature has been realized. The active part consists of a single 850 nm thick epitaxial PbSe gain layer. It is followed by a 2 1/2 pair Pb1-yEuyTe/BaF2 Bragg mirror. No microstructural processing is needed. Excitation is done optically with a 1.5 μm wavelength laser. The device operates up to 45 °C with 100 ns pulses and delivers 6 mW output power at 27 °C heat-sink temperature.

Self-Powered UV-Near Infrared Photodetector Based on Reduced Graphene Oxide/n-Si Vertical Heterojunction.

Science.gov (United States)

Li, Guanghui; Liu, Lin; Wu, Guan; Chen, Wei; Qin, Sujie; Wang, Yi; Zhang, Ting

2016-09-01

A novel self-powered photodetector based on reduced graphene oxide (rGO)/n-Si p-n vertical heterojunction with high sensitivity and fast response time is presented. The photodetector contains a p-n vertical heterojunction between a drop-casted rGO thin film and n-Si. Contacts between the semiconductor layer (rGO, n-Si) and source-drain Ti/Au electrodes allow efficient transfer of photogenerated charge carriers. The self-powered UV-near infrared photodetector shows high sensitivity toward a spectrum of light from 365 to 1200 nm. Under the 600 nm illumination (0.81 mW cm -2 ), the device has a photoresponsivity of 1.52 A W -1 , with fast response and recover time (2 ms and 3.7 ms), and the ON/OFF ratios exceed 10 4 when the power density reaches ≈2.5 mW cm -2 . The high photoresponse primarily arises from the built-in electric field formed at the interface of n-Si and rGO film. The effect of rGO thickness, rGO reduction level, and layout of rGO/n-Si effective contact area on device performance are also systematically investigated. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Network of vertically c-oriented prismatic InN nanowalls grown on c-GaN/sapphire template by chemical vapor deposition technique

Science.gov (United States)

Barick, B. K.; Saroj, Rajendra Kumar; Prasad, Nivedita; Sutar, D. S.; Dhar, S.

2018-05-01

Networks of vertically c-oriented prism shaped InN nanowalls, are grown on c-GaN/sapphire templates using a CVD technique, where pure indium and ammonia are used as metal and nitrogen precursors. A systematic study of the growth, structural and electronic properties of these samples shows a preferential growth of the islands along [ 1 1 2 bar 0 ] and [0 0 0 1] directions leading to the formation of such a network structure, where the vertically [0 0 0 1] oriented tapered walls are laterally align along one of the three [ 1 1 2 bar 0 ] directions. Inclined facets of these walls are identified as semipolar (1 1 2 bar 2) -planes of wurtzite InN. Onset of absorption for these samples is observed to be higher than the band gap of InN suggesting a high background carrier concentration in this material. Study of the valence band edge through XPS indicates the formation of positive depletion regions below the surface of the side facets [(1 1 2 bar 2) -planes] of the walls. This is in contrast with the observation for c-plane InN epilayers, where electron accumulation is often reported below the top surface.

Alignment and operability analysis of a vertical sodium pump

International Nuclear Information System (INIS)

Gupta, V.K.; Fair, C.E.

1981-01-01

With the objective of identifying important alignment features of pumps such as FFTF, HALLAM, EBR II, PNC, PHENIX, and CRBR, alignment of the vertical sodium pump for the Clinch River Breeder Reactor Plant (CRBRP) is investigated. The CRBRP pump includes a flexibly coupled pump shaft and motor shaft, two oil-film tilting-pad hydrodynamic radial bearings in the motor plus a vertical thrust bearing, and two sodium hydrostatic bearings straddling the double-suction centrifugal impeller in the pump

Influence of anaerobic physical effort in the horizontal and vertical peripheral view INFLUENCIA DEL ESFUERZO FÍSICO ANAERÓBICO EN LA VISIÓN PERIFÉRICA VERTICAL Y HORIZONTAL

Directory of Open Access Journals (Sweden)

M. Arteaga

2010-09-01

Full Text Available

There now seems to be a generalized tendency to consider that sporting performance declines as the sportsperson becomes fatigued. However, there is little empirical evidence to show that this adversely affects visual function. In some sports it is necessary to see stimuli in zones peripheral to central vision. The aim of this study is to analyze the influence of anaerobic exertion on vertical and horizontal Peripheral Vision. An intra-subject design was used with 14 replications. The visual parameters of Vertical Peripheral Vision and Horizontal Peripheral Vision were measured in different fatigue conditions to analyze the possible negative influence which this could exert on the subject’s visual capacity. The results show that fatigue due to anaerobic effort does not harm the visual abilities studied.
KEY WORDS: Peripheral Vision, Fatigue, Anaerobic exertion, Visual abilities

Parece haber una tendencia generalizada a considerar que el rendimiento deportivo disminuye en la medida en que los deportistas acumulan fatiga; sin embargo existen pocas evidencias empíricas que indiquen que la función visual se vea perjudicada por este motivo. En algunos deportes es necesario observar estímulos en zonas periféricas a la visión central. En el presente estudio se pretende analizar la influencia de los esfuerzos anaeeróbicos sobre la Visión Periférica (vertical y horizontal. Se utilizó un diseño intrasujeto A-(B1,B2-A con catorce replicaciones. Se realizaron mediciones de los parámetros visuales: Visión Periférica Vertical y Visión Periférica Horizontal en diferentes condiciones de fatiga para analizar la posible influencia negativa que pudiera ejercer ésta sobre la capacidad visual de los sujetos. Los resultados permiten afirmar que la fatiga debida a esfuerzos de tipo anaeróbico no producen un perjuicio sobre las habilidades visuales estudiadas.
PALABRAS CLAVE: Visión

Enhanced mobility in vertically scaled N-polar high-electron-mobility transistors using GaN/InGaN composite channels

Science.gov (United States)

Li, Haoran; Wienecke, Steven; Romanczyk, Brian; Ahmadi, Elaheh; Guidry, Matthew; Zheng, Xun; Keller, Stacia; Mishra, Umesh K.

2018-02-01

A GaN/InGaN composite channel design for vertically scaled N-polar high-electron-mobility transistor (HEMT) structures is proposed and demonstrated by metal-organic chemical vapor deposition. In a conventional N-polar HEMT structure, as the channel thickness (tch) decreases, the sheet charge density (ns) decreases, the electric field in the channel increases, and the centroid of the two-dimensional electron gas (2DEG) moves towards the back-barrier/channel interface, resulting in stronger scattering and lower electron mobility (μ). In this study, a thin InGaN layer was introduced in-between the channel and the AlGaN cap to increase the 2DEG density and reduce the electric field in the channel and therefore increase the electron mobility. The dependence of μ on the InGaN thickness (tInGaN) and the indium composition (xIn) was investigated for different channel thicknesses. With optimized tInGaN and xIn, significant improvements in electron mobility were observed. For a 6 nm channel HEMT structure, the electron mobility increased from 606 to 1141 cm2/(V.s) when the 6 nm thick pure GaN channel was replaced by the 4 nm GaN/2 nm In0.1Ga0.9N composite channel.

Bloque de hormigón liviano con agregados reciclados apto para generar una huerta vertical

OpenAIRE

Putruele, María Belén

2016-01-01

El área temática que abarca la investigación es “Materiales y técnicas de Construcción Sustentable”. El objetivo de este trabajo es el desarrollo y perfeccionamiento de un bloque de hormigón liviano fabricado a partir de mezclas cementicias con agregados provenientes de Residuos Sólidos Urbanos, RSU y Residuos de Construcción y Demolición, RCD. Dicho bloque permite la incorporación de una maceta para el crecimiento vertical de huerta o plantas que sirvan a la vivienda. Estos bloques cuenta...

The TEXT upgrade vertical interferometer

International Nuclear Information System (INIS)

Hallock, G.A.; Gartman, M.L.; Li, W.; Chiang, K.; Shin, S.; Castles, R.L.; Chatterjee, R.; Rahman, A.S.

1992-01-01

A far-infrared interferometer has been installed on TEXT upgrade to obtain electron density profiles. The primary system views the plasma vertically through a set of large (60-cm radialx7.62-cm toroidal) diagnostic ports. A 1-cm channel spacing (59 channels total) and fast electronic time response is used, to provide high resolution for radial profiles and perturbation experiments. Initial operation of the vertical system was obtained late in 1991, with six operating channels

Técnica de cierre vertical en labio hendido: Reporte de 837 casos y revisión de la literatura Vertical closing in lip cleft: Report of 837 cases and review of the literature

Directory of Open Access Journals (Sweden)

J.A. León Pérez

2008-09-01

Full Text Available Ninguna otra deformidad congénita tiene el potencial de alterar la forma facial tan perceptiblemente como lo hace un labio y paladar hendido, en donde el tercio medio de la cara se modifica y supone un gran desafío para el cirujano plástico. Proponemos el cierre vertical de la piel tras la miorrafia, formando una línea y tratando de dar apariencia a la columna del filtrum que no se formó en el labio hendido. Presentamos el resultado en niños operados en el Servicio de Cirugía Plástica del Instituto Nacional de Pediatría de México DF desde enero de 1998 hasta diciembre de 2006, en total 837 pacientes. La técnica quirúrgica utilizada consistió en el cierre de labio hendido en forma vertical. Del total de pacientes, 310 fueron mujeres y 527 varones; el 13% (n=109 presentaban hendidura bilateral. El 95% de los pacientes (n= 795 tuvieron un resultado estético adecuado; no se presentaron complicaciones postoperatorias inmediatas y sólo en un paciente se produjo dehiscencia de la herida. Como ventajas de la técnica podemos citar el que produce una línea cicatricial que parece la columna del filtrum hendido, el que conlleva una disección anatómica de la piel (líneas de máxima tensión y el que evita las incisiones que cruzan el filtrum o el ala nasal, con lo que la cicatriz resultante es menos visible.No other congenital deformity has the potential to alter the face form as perceivably as it makes a cleft lip and palate. The middle third of the face is altered and it represents a great challenge for plastic surgeon. We propose the vertical closing of the skin after miorraphy forming a line and trying to appear like the filtrum column that was not formed in the cleft lip. We report the result in children operated on our Service of Plastic Surgery at the Instituto Nacional de Salud, México DF, from january 1998 to december 2006, total 837 patients. Surgical technique consisted of the closing of cleft lip in vertical way. Total number

Diel vertical migration patterns of three zooplankton populations in a Chilean lake Patrones de migración vertical de tres poblaciones de zooplancton en un lago chileno

Directory of Open Access Journals (Sweden)

RODRIGO RAMOS-JILIBERTO

2004-03-01

Full Text Available In this work we analyzed the depth-distribution, at noon and midnight, of three zooplankton populations which are common inhabitants of lakes from central Chile and coexist in lake El Plateado. The species were Tumeodiaptomus diabolicus, Diaphanosoma chilense and Bosmina longirostris. Also, we analyzed the association between the depth-specific abundances of the groups and the depth-specific temperature and oxygen values during the sampling period. Our results show that: (1 the three population exhibited diel vertical migration during part of the year; (2 T. diabolicus and D. chilense exhibited the normal pattern of vertical migration, and B. longirostris presented both the normal and the reverse pattern; (3 for all species and most dates, zooplankters experience significant decreases in oxygen exposure as a consequence of downward migration. Temperature costs are less important but present in T. diabolicus and D. chilense during part of the yearEn este trabajo analizamos la distribución en profundidad, a mediodía y medianoche, de tres poblaciones de zooplancton que son habitantes comunes de los lagos de Chile central, y que coexisten en el lago El Plateado. Las especies fueron Tumeodiaptomus diabolicus, Diaphanosoma chilense y Bosmina longirostris. También analizamos la asociación entre las abundancias profundidad-específicas de los grupos y los valores profundidad-específicos de temperatura y oxígeno durante el periodo de muestreo. Nuestros resultados muestran que: (1 las tres poblaciones exhibieron migración vertical durante una parte del año; (2 T. diabolicus y D. chilense exhibieron el patrón normal de migración, y B. longirostris presentó tanto el patrón normal como el inverso; (3 para todas las especies y en la mayoría de las fechas, el zooplancton presentó reducciones significativas en su exposición al oxígeno como consecuencia de la migración descendente. Los costos térmicos son menos importantes pero existentes en T

Retrieving Vertical Air Motion and Raindrop Size Distributions from Vertically Pointing Doppler Radars

Science.gov (United States)

Williams, C. R.; Chandra, C. V.

2017-12-01

The vertical evolution of falling raindrops is a result of evaporation, breakup, and coalescence acting upon those raindrops. Computing these processes using vertically pointing radar observations is a two-step process. First, the raindrop size distribution (DSD) and vertical air motion need to be estimated throughout the rain shaft. Then, the changes in DSD properties need to be quantified as a function of height. The change in liquid water content is a measure of evaporation, and the change in raindrop number concentration and size are indicators of net breakup or coalescence in the vertical column. The DSD and air motion can be retrieved using observations from two vertically pointing radars operating side-by-side and at two different wavelengths. While both radars are observing the same raindrop distribution, they measure different reflectivity and radial velocities due to Rayleigh and Mie scattering properties. As long as raindrops with diameters greater than approximately 2 mm are in the radar pulse volumes, the Rayleigh and Mie scattering signatures are unique enough to estimate DSD parameters using radars operating at 3- and 35-GHz (Williams et al. 2016). Vertical decomposition diagrams (Williams 2016) are used to explore the processes acting on the raindrops. Specifically, changes in liquid water content with height quantify evaporation or accretion. When the raindrops are not evaporating, net raindrop breakup and coalescence are identified by changes in the total number of raindrops and changes in the DSD effective shape as the raindrops. This presentation will focus on describing the DSD and air motion retrieval method using vertical profiling radar observations from the Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) central facility in Northern Oklahoma.

Vertical stability, high elongation, and the consequences of loss of vertical control on DIII-D

International Nuclear Information System (INIS)

Kellman, A.G.; Ferron, J.R.; Jensen, T.H.; Lao, L.L.; Luxon, J.L.; Skinner, D.G.; Strait, E.J.; Reis, E.; Taylor, T.S.; Turnbull, A.D.; Lazarus, E.A.; Lister, J.B.

1990-09-01

Recent modifications to the vertical control system for DIII-D has enabled operation of discharges with vertical elongation κ, up to 2.5. When vertical stability is lost, a disruption follows and a large vertical force on the vacuum vessel is observed. The loss of plasma energy begins when the edge safety factor q is 2 but the current decay does not begin until q ∼1.3. Current flow on the open field lines in the plasma scrapeoff layer has been measured and the magnitude and distribution of these currents can explain the observed force on the vessel. Equilibrium calculations and simulation of this vertical displacement episode are presented. 7 refs., 4 figs

On Properties of Class A(n and n-Paranormal Operators

Directory of Open Access Journals (Sweden)

Xiaochun Li

2014-01-01

both non-zero operators; secondly we consider the properties for n-paranormal operators, showing that a n-paranormal contraction is the direct sum of a unitary and a C.0 completely non-unitary contraction.

Effects of Atmospheric Water Vapor and Clouds on NOAA (National Oceanic and Atmospheric Administration) AVHRR (Advanced Very High Resolution Radiometer) Satellite Data.

Science.gov (United States)

1984-07-01

the effect of inadequate information about world food supplies. The impact of the Soviet grain buys of 1972 are a case in point. The last ten...First came TIROS-I ( Televison and Infrared Observational Satellite) in the early 1960’s. The TIROS Operational Satellite (TOS) or ESSA 5 (Environmental...these items impact on the calculated VIN. Other than water, most objects in a scene transmit very little visible solar radiation. The energy

The influence of silicon wafer thickness on characteristics of multijunction solar cells with vertical p—n-junctions

Directory of Open Access Journals (Sweden)

Gnilenko A. B.

2012-02-01

Full Text Available A multijunction silicon solar cell with vertical p–n junctions consisted of four serial n+–p–p+-structures was simulated using Silvaco TCAD software package. The dependence of solar cell characteristics on the silicon wafer thickness is investigated for a wide range of values.

Investigation of the GaN-on-GaAs interface for vertical power device applications

International Nuclear Information System (INIS)

Möreke, Janina; Uren, Michael J.; Kuball, Martin; Novikov, Sergei V.; Foxon, C. Thomas; Hosseini Vajargah, Shahrzad; Wallis, David J.; Humphreys, Colin J.; Haigh, Sarah J.; Al-Khalidi, Abdullah; Wasige, Edward; Thayne, Iain

2014-01-01

GaN layers were grown onto (111) GaAs by molecular beam epitaxy. Minimal band offset between the conduction bands for GaN and GaAs materials has been suggested in the literature raising the possibility of using GaN-on-GaAs for vertical power device applications. I-V and C-V measurements of the GaN/GaAs heterostructures however yielded a rectifying junction, even when both sides of the junction were heavily doped with an n-type dopant. Transmission electron microscopy analysis further confirmed the challenge in creating a GaN/GaAs Ohmic interface by showing a large density of dislocations in the GaN layer and suggesting roughening of the GaN/GaAs interface due to etching of the GaAs by the nitrogen plasma, diffusion of nitrogen or melting of Ga into the GaAs substrate.

Investigation of the GaN-on-GaAs interface for vertical power device applications

Energy Technology Data Exchange (ETDEWEB)

Möreke, Janina, E-mail: janina.moereke@bristol.ac.uk; Uren, Michael J.; Kuball, Martin [H.H. Wills Physics Laboratory, Tyndall Avenue, Bristol BS8 1TL (United Kingdom); Novikov, Sergei V.; Foxon, C. Thomas [Department of Physics and Astronomy, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Hosseini Vajargah, Shahrzad; Wallis, David J.; Humphreys, Colin J. [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Haigh, Sarah J. [Super STEM Laboratory, STFC Daresbury Campus, Keckwick Lane, Daresbury WA4 4AD (United Kingdom); School of Materials, University of Manchester, Manchester M13 9PL (United Kingdom); Al-Khalidi, Abdullah; Wasige, Edward; Thayne, Iain [School of Engineering, University of Glasgow, Rankine Bldg, Oakfield Avenue, Glasgow G12 8LT (United Kingdom)

2014-07-07

GaN layers were grown onto (111) GaAs by molecular beam epitaxy. Minimal band offset between the conduction bands for GaN and GaAs materials has been suggested in the literature raising the possibility of using GaN-on-GaAs for vertical power device applications. I-V and C-V measurements of the GaN/GaAs heterostructures however yielded a rectifying junction, even when both sides of the junction were heavily doped with an n-type dopant. Transmission electron microscopy analysis further confirmed the challenge in creating a GaN/GaAs Ohmic interface by showing a large density of dislocations in the GaN layer and suggesting roughening of the GaN/GaAs interface due to etching of the GaAs by the nitrogen plasma, diffusion of nitrogen or melting of Ga into the GaAs substrate.

Enhancement of slope efficiency and output power in GaN-based vertical-cavity surface-emitting lasers with a SiO2-buried lateral index guide

Science.gov (United States)

Kuramoto, Masaru; Kobayashi, Seiichiro; Akagi, Takanobu; Tazawa, Komei; Tanaka, Kazufumi; Saito, Tatsuma; Takeuchi, Tetsuya

2018-03-01

We have achieved a high output power of 6 mW from a 441 nm GaN-based vertical-cavity surface-emitting laser (VCSEL) under continuous wave (CW) operation, by reducing both the internal loss and the reflectivity of the front cavity mirror. A preliminary analysis of the internal loss revealed an enormously high transverse radiation loss in a conventional GaN-based VCSEL without lateral optical confinement (LOC). Introducing an LOC structure enhanced the slope efficiency by a factor of 4.7, with a further improvement to a factor of 6.7 upon reducing the front mirror reflectivity. The result was a slope efficiency of 0.87 W/A and an external differential quantum efficiency of 32% under pulsed operation. A flip-chip-bonded VCSEL also exhibited a high slope efficiency of 0.64 W/A and an external differential quantum efficiency of 23% for the front-side output under CW operation. The reflectivity of the cavity mirror was adjusted by varying the number of AlInN/GaN distributed Bragg reflector pairs from 46 to 42, corresponding to reflectivity values from 99.8% to 99.5%. These results demonstrate that a combination of internal loss reduction and cavity mirror control is a very effective way of obtaining a high output GaN-based VCSEL.

Effects of polarization field on vertical transport in GaN/AlGaN resonant tunneling diodes

International Nuclear Information System (INIS)

Park, Seoung-Hwan; Shim, Jong-In

2012-01-01

Polarization-field effects on the vertical transport in GaN/AlGaN resonant tunneling diodes (RTDs) were theoretically investigated by using the transfer matrix formalism. The self-consistent model shows that the resonant peaks are shifted toward higher energies with increasing Al composition in the AlGaN barrier, and the transmission probability values are shown to decrease rapidly. In the case of the flat-band model, on the other hand, the shift of the resonant peaks is smaller than it is for the self-consistent model and the variation of transmission probability values with increasing Al composition is relatively smaller than that of the self-consistent model. The current voltage characteristics of the self-consistent model are asymmetric while those of the flat-band model are symmetric for positive and negative current directions. The peak-to-valley ratio (PVR) of the self-consistent model is shown to be slightly smaller than that of the flat-band model for Al = 0.3.

Vertical MoSe2-MoO x p-n heterojunction and its application in optoelectronics

Science.gov (United States)

Chen, Xiaoshuang; Liu, Guangbo; Hu, Yunxia; Cao, Wenwu; Hu, PingAn; Hu, Wenping

2018-01-01

The hybrid n-type 2D transition-metal dichalcogenide (TMD)/p-type oxide van der Waals (vdW) heterojunction nanosheets consist of 2D layered MoSe2 (the n-type 2D material) and MoO x (the p-type oxide) which are grown on SiO2/Si substrates for the first time via chemical vapor deposition technique, displaying the regular hexagon structures with the average length dimension of sides of ˜8 μm. Vertical MoSe2-MoO x p-n heterojunctions demonstrate obviously current-rectifying characteristic, and it can be tuned via gate voltage. What is more, the photodetector based on vertical MoSe2-MoO x heterojunctions displays optimal photoresponse behavior, generating the responsivity, detectivity, and external quantum efficiency to 3.4 A W-1, 0.85 × 108 Jones, and 1665.6%, respectively, at V ds = 5 V with the light wavelength of 254 nm under 0.29 mW cm-2. These results furnish a building block on investigating the flexible and transparent properties of vdW and further optimizing the structure of the devices for better optoelectronic and electronic performance.

Diseño de un aerogenerador de eje vertical tipo Savonius para electrificación rural

OpenAIRE

Arbeloa Sola, Lorena

2012-01-01

Este proyecto fin de carrera describe el cálculo y el diseño de un aerogenerador de eje vertical tipo Savonius para electrificación rural aprovechando la energía del viento. El objeto de este proyecto es proporcionar toda la información necesaria para la construcción e instalación de un aerogenerador de este tipo en una comunidad boliviana, concretamente en la comunidad de Vilacollo, situada en el departamento de Oruro, en la parte oeste de Bolivia. Si dicho proyecto resulta e...

Entrenamiento propioceptivo para la remada de soporte en vertical en natación sincronizada

OpenAIRE

Hernández Mendizábal, Silvia

2015-01-01

Una de las técnicas más utilizadas en natación sincronizada son las remadas y, en concreto; La remada americana, utilizada para mantener las piernas por encima de la superficie mientras el cuerpo se mantiene en vertical cabeza abajo, por debajo del agua. Homma, Homma y Washizuya (2008) describen la función de esta remada como: "remada propulsiva y de soporte, utilizada con el objetivo de mantener la máxima altura fuera del agua". Estudios biomecánicos han profundizado con sistemas bidimension...

Satisfacción de necesidades de anticoncepción en mujeres positivas al VIH: efecto sobre la eliminación de la transmisión vertical del virus

Directory of Open Access Journals (Sweden)

Marcela Gómez-Suárez

Full Text Available RESUMEN Cerca de 38% de embarazos no planeados se dan por necesidades insatisfechas en anticoncepción. En las mujeres positivas al VIH, las cifras se triplican, un fenómeno explicado por determinantes sociales como la pobreza, el acceso a los servicios de salud, la violencia y el desplazamiento forzoso, todos ellos elementos propios de la vida de estas mujeres. Los embarazos no planeados representan una carga psicológica vinculada con el temor de transmitir la infección a sus hijos, la orfandad y el asumir los riesgos durante el embarazo, a lo cual se añaden las consecuencias familiares y sociales que se manifiestan en baja asistencia al control prenatal, descuido de la salud y aumento de la posibilidad de transmisión vertical. El asesoramiento en anticoncepción diferencial e integrado a los servicios de atención y control del VIH es básico para lograr la eliminación de la transmisión vertical del VIH a corto y medio plazo. Reconocer que estas mujeres tienen características diferentes a las de la población general, como expresan su vida reproductiva, sus deseos e intenciones sobre la maternidad y que los embarazos no planeados representan una carga psicológica, social y económica adicional a la de las demás mujeres permitiría que el asesoramiento en anticoncepción se proporcionara en los programas de atención y seguimiento del VIH, en el mismo lugar y momento, con personal capacitado, capaz de comprender y atender sus necesidades reproductivas dentro de un marco de derechos, logrando que los sistemas de salud, basados en la responsabilidad que tienen con la sociedad, fueran capaces de ofrecer un asesoramiento en reproducción de calidad y dirigido a satisfacer las necesidades específicas de estas mujeres.

An electromagnetic screw and nut system for operating vertical motions along an axis

International Nuclear Information System (INIS)

Fehr, Henri.

1975-01-01

This invention concerns a magnetic screw and nut system for operating control rods, designed for vertical mounting and having no mobile or slide contacts. It makes it possible to rotate a screw located inside a sealed tubular containment that can have a very thick wall. All the electromagnetic components entering into the operation are outside this containment. The magnetic screw has a constant air gap. The tube, manufactured of a non-magnetic material, includes two added annular pole pieces forming part of its wall and whose internal surfaces have a thread corresponding to that of the screw. The two annular pole pieces are spaced axially from each other by an amount equal to an integral number of thread pitches. An external winding and magnetic armature associated to these pole pieces form the fixed magnetic nut. A multiphase non-synchronous motor is placed around the tube and near the nut, the stator is external, the rotor is the screw. An appliance for fixing the degree of axial displacement freedom of the screw can be provided [fr

Integrability in N=2 superconformal gauge theorie

Energy Technology Data Exchange (ETDEWEB)

Pomoni, Elli [Deutsches Elektronen-Synchrotron DESY, Hamburg (Germany). Theory Group; National Technical Univ. of Athens (Greece). Physics Div.

2013-10-15

Any N=2 superconformal gauge theory (including N=4 SYM) contains a set of local operators made only out of fields in the N=2 vector multiplet that is closed under renormalization to all loops, namely the SU(2,1 vertical stroke 2) sector. For planar N=4 SYM the spectrum of local operators can be obtained by mapping the problem to an integrable model (a spin chain in perturbation theory), in principle for any value of the coupling constant. We present a diagrammatic argument that for any planar N=2 superconformal gauge theory the SU(2,1 vertical stroke 2) Hamiltonian acting on infinite spin chains is identical to all loops to that of N=4 SYM, up to a redefinition of the coupling constant. Thus, this sector is integrable and anomalous dimensions can be, in principle, read off from the N=4 ones up to this redefinition.

Integrability in N=2 superconformal gauge theories

International Nuclear Information System (INIS)

Pomoni, Elli; National Technical Univ. of Athens

2013-10-01

Any N=2 superconformal gauge theory (including N=4 SYM) contains a set of local operators made only out of fields in the N=2 vector multiplet that is closed under renormalization to all loops, namely the SU(2,1 vertical stroke 2) sector. For planar N=4 SYM the spectrum of local operators can be obtained by mapping the problem to an integrable model (a spin chain in perturbation theory), in principle for any value of the coupling constant. We present a diagrammatic argument that for any planar N=2 superconformal gauge theory the SU(2,1 vertical stroke 2) Hamiltonian acting on infinite spin chains is identical to all loops to that of N=4 SYM, up to a redefinition of the coupling constant. Thus, this sector is integrable and anomalous dimensions can be, in principle, read off from the N=4 ones up to this redefinition.

Determinantes de la transmisión vertical del VIH en Cataluña (1997-2001: ¿es posible su eliminación?

Directory of Open Access Journals (Sweden)

Ramos F.

2003-01-01

Full Text Available Objetivos: Identificar y describir los factores que han hecho posible la existencia de nuevas infecciones de VIH por transmisión vertical desde la implementación del tratamiento antirretroviral en la gestante seropositiva (1997-2001 en Cataluña. Métodos: Revisión sistemática de casos identificados en servicios de pediatría de todos los hospitales de Cataluña. Resultados: Se identificaron 28 casos de infección pediátrica por VIH: 9, 9, 8, 2 y 0 por año de nacimiento de 1997 a 2001, respectivamente. De 16 madres con diagnóstico de infección por VIH conocido antes o durante el embarazo, 9 realizaron profilaxis antirretroviral durante éste (5 con buena adhesión, uno desconocido y el resto con mala adhesión y 7 no realizaron profilaxis (6 por rechazo y uno no se conoce. De 12 diagnosticadas después del parto, 5 fueron embarazos no controlados y el resto poco o bien controlados. De estos últimos, en 6 no se practicó serología para VIH y en uno fue negativa en el primer trimestre. Conclusiones: La transmisión vertical del VIH en Cataluña ha disminuido en los últimos años, pero se han producido infecciones por la mala implementación en algún caso de las medidas preventivas conocidas. Debería ofrecerse la prueba diagnóstica para VIH a toda gestante no sólo en el primer trimestre de embarazo sino también al final, si se sospecha exposición al virus, y en caso de gestaciones no controladas hay que usar pruebas diagnósticas de lectura rápida en la sala de partos.

Transmisión vertical del VIH: Comprendiendo el sentimiento de los padres por la técnica proyectiva HIV Vertical Transmission: Understanding the parents' feelings through the projective technique

OpenAIRE

Janie Maria de Almeida; Neide de Souza Praça

2009-01-01

Estudio cualitativo realizado con padres de lactantes expuestos al VIH, cuya madre está inscrita en el Programa Transmisión Vertical Cero, Sorocaba, SP. El objetivo es identificar sentimientos relacionados con la fe religiosa de estos padres ante la indefinición del diagnóstico para el VIH del lactante. La investigación fue aprobada por un Comité de Ética en Investigación y siguió la Resolución 196/96. Para la recolección de datos se empleó la técnica proyectiva con montaje elaborada a partir...

Vertically aligned Ta3N5 nanorod arrays for solar-driven photoelectrochemical water splitting

KAUST Repository

Li, Yanbo; Takata, Tsuyoshi; Cha, Dong Kyu; Takanabe, Kazuhiro; Minegishi, Tsutomu; Kubota, Jun; Domen, Kazunari

2012-01-01

A vertically aligned Ta3N5 nanorod photoelectrode is fabricated by through-mask anodization and nitridation for water splitting. The Ta3N5 nanorods, working as photoanodes of a photoelectrochemical cell, yield a high photocurrent density of 3.8 mA cm -2 at 1.23 V versus a reversible hydrogen electrode under AM 1.5G simulated sunlight and an incident photon-to-current conversion efficiency of 41.3% at 440 nm, one of the highest activities reported for photoanodes so far. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Vertically aligned Ta3N5 nanorod arrays for solar-driven photoelectrochemical water splitting

KAUST Repository

Li, Yanbo

2012-09-18

A vertically aligned Ta3N5 nanorod photoelectrode is fabricated by through-mask anodization and nitridation for water splitting. The Ta3N5 nanorods, working as photoanodes of a photoelectrochemical cell, yield a high photocurrent density of 3.8 mA cm -2 at 1.23 V versus a reversible hydrogen electrode under AM 1.5G simulated sunlight and an incident photon-to-current conversion efficiency of 41.3% at 440 nm, one of the highest activities reported for photoanodes so far. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Thrust stand for vertically oriented electric propulsion performance evaluation

Energy Technology Data Exchange (ETDEWEB)

Moeller, Trevor [University of Tennessee Space Institute, Tullahoma, Tennessee 37388 (United States); Polzin, Kurt A. [NASA, Marshall Space Flight Center, Huntsville, Alabama 35812 (United States)

2010-11-15

A variation of a hanging pendulum thrust stand capable of measuring the performance of an electric thruster operating in the vertical orientation is presented. The vertical orientation of the thruster dictates that the thruster must be horizontally offset from the pendulum pivot arm, necessitating the use of a counterweight system to provide a neutrally stable system. Motion of the pendulum arm is transferred through a balance mechanism to a secondary arm on which deflection is measured. A noncontact light-based transducer is used to measure displacement of the secondary beam. The members experience very little friction, rotating on twisting torsional pivots with oscillatory motion attenuated by a passive, eddy-current damper. Displacement is calibrated using an in situ thrust calibration system. Thermal management and self-leveling systems are incorporated to mitigate thermal and mechanical drifts. Gravitational force and torsional spring constants associated with flexure pivots provide restoring moments. An analysis of the design indicates that the thrust measurement range spans roughly four decades, with the stand capable of measuring thrust up to 12 N for a 200 kg thruster and up to approximately 800 mN for a 10 kg thruster. Data obtained from calibration tests performed using a 26.8 lbm simulated thruster indicated a resolution of 1 mN on 100 mN level thrusts, while those tests conducted on a 200 lbm thruster yielded a resolution of roughly 2.5 mN at thrust levels of 0.5 N and greater.

Thrust stand for vertically oriented electric propulsion performance evaluation

International Nuclear Information System (INIS)

Moeller, Trevor; Polzin, Kurt A.

2010-01-01

A variation of a hanging pendulum thrust stand capable of measuring the performance of an electric thruster operating in the vertical orientation is presented. The vertical orientation of the thruster dictates that the thruster must be horizontally offset from the pendulum pivot arm, necessitating the use of a counterweight system to provide a neutrally stable system. Motion of the pendulum arm is transferred through a balance mechanism to a secondary arm on which deflection is measured. A noncontact light-based transducer is used to measure displacement of the secondary beam. The members experience very little friction, rotating on twisting torsional pivots with oscillatory motion attenuated by a passive, eddy-current damper. Displacement is calibrated using an in situ thrust calibration system. Thermal management and self-leveling systems are incorporated to mitigate thermal and mechanical drifts. Gravitational force and torsional spring constants associated with flexure pivots provide restoring moments. An analysis of the design indicates that the thrust measurement range spans roughly four decades, with the stand capable of measuring thrust up to 12 N for a 200 kg thruster and up to approximately 800 mN for a 10 kg thruster. Data obtained from calibration tests performed using a 26.8 lbm simulated thruster indicated a resolution of 1 mN on 100 mN level thrusts, while those tests conducted on a 200 lbm thruster yielded a resolution of roughly 2.5 mN at thrust levels of 0.5 N and greater.

A GaInAsP/InP Vertical Cavity Surface Emitting Laser for 1.5 m m operation

Science.gov (United States)

Sceats, R.; Balkan, N.; Adams, M. J.; Masum, J.; Dann, A. J.; Perrin, S. D.; Reid, I.; Reed, J.; Cannard, P.; Fisher, M. A.; Elton, D. J.; Harlow, M. J.

1999-04-01

We present the results of our studies concerning the pulsed operation of a bulk GaInAsP/InP vertical cavity surface emitting laser (VCSEL). The device is tailored to emit at around 1.5 m m at room temperature. The structure has a 45 period n-doped GaInAsP/InP bottom distributed Bragg reflector (DBR), and a 4 period Si/Al2O3 dielectric top reflector defining a 3-l cavity. Electroluminescence from a 16 m m diameter top window was measured in the pulsed injection mode. Spectral measurements were recorded in the temperature range between 125K and 240K. Polarisation, lasing threshold current and linewidth measurements were also carried out at the same temperatures. The threshold current density has a broad minimum at temperatures between 170K and 190K, (Jth=13.2 kA/cm2), indicating a good match between the gain and the cavity resonance in this temperature range. Maximum emitted power from the VCSEL is 0.18 mW at 180K.

¿La integración vertical mejora la rentabilidad económica de las empresas agroalimentarias?

OpenAIRE

Sopena Canosa, Mireia; Moreno Gené, Jordi

2017-01-01

El objetivo del trabajo consiste en averiguar si la integración vertical hacía atrás, llevada a cabo en empresas del sector agroalimentario español durante los años de crisis financiera, supone una estrategia que permita mejorar la rentabilidad económica de un sector caracterizado por una gran presencia de empresas familiares, a quienes este tipo de estrategia también puede interesar para evitar conflictos familiares derivados de la gestión. Para ello, se han analizado un total...

Formation of conductive spontaneous via holes in AlN buffer layer on n+Si substrate by filling the vias with n-AlGaN by metal organic chemical vapor deposition and application to vertical deep ultraviolet photo-sensor

Directory of Open Access Journals (Sweden)

N. Kurose

2014-12-01

Full Text Available We have grown conductive aluminum nitride (AlN layers using the spontaneous via holes formation technique on an n+-Si substrate for vertical-type device fabrication. The size and density of the via holes are controlled through the crystal growth conditions used for the layer, and this enables the conductance of the layer to be controlled. Using this technique, we demonstrate the fabrication of a vertical-type deep ultraviolet (DUV photo-sensor. This technique opens up the possibility of fabrication of monolithically integrated on-chip DUV sensors and DUV light-emitting devices (LEDs, including amplifiers, controllers and other necessary functional circuits, on a Si substrate.

High-performance PbS quantum dot vertical field-effect phototransistor using graphene as a transparent electrode

Science.gov (United States)

Che, Yongli; Zhang, Yating; Cao, Xiaolong; Song, Xiaoxian; Zhang, Haiting; Cao, Mingxuan; Dai, Haitao; Yang, Junbo; Zhang, Guizhong; Yao, Jianquan

2016-12-01

Solution processed photoactive PbS quantum dots (QDs) were used as channel in high-performance near-infrared vertical field-effect phototransistor (VFEpT) where monolayer graphene embedded as transparent electrode. In this vertical architecture, the PbS QD channel was sandwiched and naturally protected between the drain and source electrodes, which made the device ultrashort channel length (110 nm) simply the thickness of the channel layer. The VFEpT exhibited ambipolar operation with high mobilities of μe = 3.5 cm2/V s in n-channel operation and μh = 3.3 cm2/V s in p-channel operation at low operation voltages. By using the photoactive PbS QDs as channel material, the VFEpT exhibited good photoresponse properties with a responsivity of 4.2 × 102 A/W, an external quantum efficiency of 6.4 × 104% and a photodetectivity of 2.1 × 109 Jones at the light irradiance of 36 mW/cm2. Additionally, the VFEpT showed excellent on/off switching with good stability and reproducibility and fast response speed with a short rise time of 12 ms in n-channel operation and 10.6 ms in p-channel operation. These high mobilities, good photoresponse properties and simplistic fabrication of our VFEpTs provided a facile route to the high-performance inorganic photodetectors.

All tree-level MHV form factors in N=4 SYM from twistor space

Energy Technology Data Exchange (ETDEWEB)

Koster, Laura [Institut für Mathematik, Institut für Physik und IRIS Adlershof,Humboldt-Universität zu Berlin, Zum Großen Windkanal 6, 12489 Berlin (Germany); Mitev, Vladimir [Institut für Mathematik, Institut für Physik und IRIS Adlershof,Humboldt-Universität zu Berlin, Zum Großen Windkanal 6, 12489 Berlin (Germany); PRISMA Cluster of Excellence, Institut für Physik, WA THEP,Johannes Gutenberg-Universität Mainz, Staudingerweg 7, 55128 Mainz (Germany); Staudacher, Matthias [Institut für Mathematik, Institut für Physik und IRIS Adlershof,Humboldt-Universität zu Berlin, Zum Großen Windkanal 6, 12489 Berlin (Germany); Wilhelm, Matthias [Institut für Mathematik, Institut für Physik und IRIS Adlershof,Humboldt-Universität zu Berlin, Zum Großen Windkanal 6, 12489 Berlin (Germany); Niels Bohr Institute, Copenhagen University,Blegdamsvej 17, 2100 Copenhagen (Denmark)

2016-06-28

We incorporate all gauge-invariant local composite operators into the twistor-space formulation of N=4 SYM theory, detailing and expanding on ideas we presented recently in http://arxiv.org/abs/1603.04471. The vertices for these operators contain infinitely many terms and we show how they can be constructed by taking suitable derivatives of a light-like Wilson loop in twistor space and shrinking it down to a point. In particular, these vertices directly yield the tree-level MHV super form factors of all composite operators in N=4 SYM theory.

Numerical analysis of the cylindrical rigidity of the vertical steel tank shell

Science.gov (United States)

Chirkov, Sergey; Tarasenko, Alexander; Chepur, Petr

2017-10-01

The paper deals with the study of rigidity of a vertical steel cylindrical tank and its structural elements with the development of inhomogeneous subsidence in ANSYS software complex. The limiting case is considered in this paper: a complete absence of a base sector that varies along an arc of a circle. The subsidence zone is modeled by the parameter n. A finite-element model of vertical 20000 m3 steel tank has been created, taking into account all structural elements of tank metal structures, including the support ring, beam frame and roof sheets. Various combinations of vertical steel tank loading are analyzed. For operational loads, the most unfavorable combination is considered. Calculations were performed for the filled and emptied tank. Values of the maximum possible deformations of the outer contour of the bottom are obtained with the development of inhomogeneous base subsidence for the given tank size. The obtained parameters of intrinsic rigidity (deformability) of vertical steel tank can be used in the development of new regulatory and technical documentation for tanks.

Immediate effect on vertical jumping ability after the completion of trampoline jumping Efecto inmediato sobre la capacidad de salto vertical después de la realización de saltos en cama elástica

Directory of Open Access Journals (Sweden)

M. Fernández del Olmo

2010-09-01

Full Text Available

The purpose of this study was to value the immediate effect on the capacity of vertical jump, caused by the execution of continuous jumps in a trampoline. Nine subjects (23,4 ± 2.83 years, males and sportsmen with prior experience in the execution of countermovement jump (CMJ, they carried out a series of continuous vertical jumps on a trampoline during 60 seconds, being valued the capacity of jump in platform of contacts before and after this activity. The electromyographic (EMG activity was registered of five muscles of the right leg (gluteus, biceps femoris, vastus lateralis, gastrocnemius medialis and soleus in all the CMJ. The height of jump diminished significantly (p <0.01 after the execution of the jumps in the trampoline, being recovered in a brief period of time. Themselves differences were not observed in the EMG for the root mean squared (RMS or in the amplitude in none of the muscles, neither in the phase of impulse, neither in the 50 ms previous to start of the jump. In the neuromuscular pattern, in spite of the great variability existing inter and intraindividual, a significant delay was identified (p<0.05 in the activation of the biceps femoris immediately after the trampoline. Keeping in mind these results, seems probably that the smaller height of the vertical jump reached after the trampoline be more attributable to a modification in the temporary characteristics and sequence of activation of the muscles that to a decrease in the activation of the same.
KEY WORDS: Vertical Jump, Neuromuscular pattern, Sprung surface, Electromyography.

El propósito de este estudio fue valorar el efecto inmediato sobre la capacidad de salto vertical, provocado por la realización de saltos continuos en una cama elástica. Nueve sujetos (23,4 ± 2,83 años, varones y deportistas con experiencia previa en la ejecución del

Straddle packer system design and operation for vertical characterization of open bore holes

International Nuclear Information System (INIS)

Olsen, J.K.

1994-01-01

Bore holes open to large intervals provide groundwater samples and test results which represent an unknown integration of properties throughout the depth of the hole. The State of Idaho's INEL Oversight Program is utilizing a custom straddle-packer system to develop a vertical characterization of water chemistry and hydrology in selected open bore holes at the Idaho National Engineering Laboratory. This report describes the design and operation for bore hole zone isolation, water sampling, and hydrologic testing. To reduce potential influences on in situ water chemistry, the system utilizes chemically inert components to the extent possible. Straddle packer systems are effective in producing representative water samples from isolated formations. Hydrologic testing is limited by the ability to produce a measurable stress on the aquifer in individual formations, and head measurement sensitivity. 4 figs

Thrust Stand for Vertically Oriented Electric Propulsion Performance Evaluation

Science.gov (United States)

Moeller, Trevor; Polzin, Kurt A.

2010-01-01

A variation of a hanging pendulum thrust stand capable of measuring the performance of an electric thruster operating in the vertical orientation is presented. The vertical orientation of the thruster dictates that the thruster must be horizontally offset from the pendulum pivot arm, necessitating the use of a counterweight system to provide a neutrally-stable system. Motion of the pendulum arm is transferred through a balance mechanism to a secondary arm on which deflection is measured. A non-contact light-based transducer is used to measure displacement of the secondary beam. The members experience very little friction, rotating on twisting torsional pivots with oscillatory motion attenuated by a passive, eddy current damper. Displacement is calibrated using an in situ thrust calibration system. Thermal management and self-leveling systems are incorporated to mitigate thermal and mechanical drifts. Gravitational restoring force and torsional spring constants associated with flexure pivots provide restoring moments. An analysis of the design indicates that the thrust measurement range spans roughly four decades, with the stand capable of measuring thrust up to 12 N for a 200 kg thruster and up to approximately 800 mN for a 10 kg thruster. Data obtained from calibration tests performed using a 26.8 lbm simulated thruster indicated a resolution of 1 mN on 100 mN-level thrusts, while those tests conducted on 200 lbm thruster yielded a resolution of roughly 2.5 micro at thrust levels of 0.5 N and greater.

Steady-state characteristics of lateral p-n junction vertical-cavity surface-emitting lasers

Science.gov (United States)

Ryzhii, V.; Tsutsui, N.; Khmyrova, I.; Ikegami, T.; Vaccaro, P. O.; Taniyama, H.; Aida, T.

2001-09-01

We developed an analytical device model for lateral p-n junction vertical-cavity surface-emitting lasers (LJVCSELs) with a quantum well active region. The model takes into account the features of the carrier injection, transport, and recombination in LJVCSELs as well as the features of the photon propagation in the cavity. This model is used for the calculation and analysis of the LJVCSEL steady-state characteristics. It is shown that the localization of the injected electrons primarily near the p-n junction and the reabsorption of lateral propagating photons significantly effects the LJVCSELs performance, in particular, the LJVCSEL threshold current and power-current characteristics. The reincarnation of electrons and holes due to the reabsorption of lateral propagating photons can substantially decrease the threshold current.

TIRO Y LAS FLUCTUACIONES DE LA ECONOMÍA FENICIA DURANTE EL SIGLO VIII ANTES DE NUESTRA ERA (Tyre and the Fluctuations of Phoenician Economy during the 8th Century BC

Directory of Open Access Journals (Sweden)

Pascual Izquierdo-Egea

2014-12-01

Full Text Available La aplicación del método de valoración contextual al análisis de los ajuares funerarios hasta ahora publicados de la necrópolis fenicia de Tiro-Al Bass, Líbano, permite aislar las fluctuaciones económicas y los cambios sociales experimentados por la población tiria durante el siglo VIII a. C. En concreto, se detecta una larga prosperidad desde mediados del siglo IX hasta mediados del VIII antes de nuestra era, con un máximo de bonanza a lo largo del periodo 775-750 a. C. En cambio, la segunda mitad del siglo VIII muestra una aguda crisis económica asociada a una elevada conflictividad social. Estos resultados coinciden plenamente con los acontecimientos históricos conocidos a través de las fuentes literarias antiguas, aportando evidencias que las complementan. En todo caso, con este nuevo ejemplo se confirma, una vez más, la universalidad de la metodología empleada y su irrefutable validez científica. ENGLISH: By applying the contextual valuation method to the analysis of grave goods from the Phoenician cemetery of Tyre-Al Bass, Lebanon, we can isolate the economic fluctuations and social changes experienced by the Tyrian population during the 8th century BC. Based on the evidence, the mid-9th to the mid-8th century BC was a period of prosperity, with the most pronounced economic boom between 775-750 BC. In contrast, the second half of the 8th century BC shows a sharp economic crisis associated with a high level of social conflict. These results are fully consistent with the historical events known through ancient literary sources. This new example confirms the universality of this methodology and its irrefutable scientific validity.

Inservice testing of vertical pumps

International Nuclear Information System (INIS)

Cornman, R.E. Jr.; Schumann, K.E.

1994-01-01

This paper focuses on the problems that may occur with vertical pumps while inservice tests are conducted in accordance with existing American Society of Mechanical Engineers Code, Section XI, standards. The vertical pump types discussed include single stage, multistage, free surface, and canned mixed flow pumps. Primary emphasis is placed on the hydraulic performance of the pump and the internal and external factors to the pump that impact hydraulic performance. In addition, the paper considers the mechanical design features that can affect the mechanical performance of vertical pumps. The conclusion shows how two recommended changes in the Code standards may increase the quality of the pump's operational readiness assessment during its service life

INTELIGENCIA Y RENDIMIENTO DEPORTIVO: UN ESTUDIO SOBRE LA INTELIGENCIA EMOCIONAL

Directory of Open Access Journals (Sweden)

Gerardo Araya Vargas

2001-06-01

Full Text Available Este estudio tuvo el propósito de determinar la correlación entre los índices de inteligencia tradicional (razonamiento analógico, C. I. e inteligencia emocional (C.E. con el rendimiento deportivo. Participaron 10 basketbolistas, entre los 17 y 25 años (media = 20.1 años, todas mujeres. Se les aplicó pruebas de C. I. (Raven y de C. E. (Goleman y luego se sometió a los sujetos a dos pruebas de precisión (tiro libre y tiro de tres puntos y posteriormente el entrenador evaluó mediante la Escala de Rendimiento Emocional Percibido por el Técnico, la capacidad de manejo emocional de las basketbolistas en situación de juego. El puntaje de C. E. se correlacionó significativamente (r=0.71; p < 0.05 con la precisión en el tiro de tres puntos. En los otros casos las correlaciones fueron bajas y no significativas. La evaluación del entrenador mostró (rbis = -0.87; p < 0.05 correlación significativa y negativa entre el índice C. E. y la percepción del efecto negativo de las emociones sobre el rendimiento, por tanto existe evidencia preliminar de que este índice podría ser valioso como predictor del rendimiento en circunstancias de alta exigencia.

NASA News

Science.gov (United States)

1983-01-01

The launch of NOAA E, an advanced TIROS N (ATN) environmental monitoring satellite, carrying special search and rescue instrumentation is announced. NOAA E carries instrumentation for a demonstration to search and rescue (SAR) mission agencies for evaluation of a satellite aided SAR system that may lead to the establishment of an operational capability. The ability of a spaceborne system to acquire, track and locate existing Emergency Locator Transmitters (ELTs) and Emergency Position Indicating Radio Beacons (EPIRBs) that are being used aboard general aviation and other aircraft, and ships, and are operating on 121.5 and 243 Megahertz frequencies is demonstrated.

Information operator approach applied to the retrieval of vertical distributions of atmospheric constituents from ground-based FTIR measurements

Science.gov (United States)

Senten, Cindy; de Mazière, Martine; Vanhaelewyn, Gauthier; Vigouroux, Corinne; Delmas, Robert

2010-05-01

The retrieval of information about the vertical distribution of an atmospheric absorber from high spectral resolution ground-based Fourier Transform infrared (FTIR) solar absorption spectra is an important issue in remote sensing. A frequently used technique at present is the optimal estimation method. This work introduces the application of an alternative method, namely the information operator approach (Doicu et al., 2007; Hoogen et al., 1999), for extracting the available information from such FTIR measurements. This approach has been implemented within the well-known retrieval code SFIT2, by adapting the optimal estimation method such as to take into account only the significant contributions to the solution. In particular, we demonstrate the feasibility of the method when applied to ground-based FTIR spectra taken at the southern (sub)tropical site Ile de La Réunion (21° S, 55° E) in 2007. A thorough comparison has been made between the retrieval results obtained with the original optimal estimation method and the ones obtained with the information operator approach, regarding profile and column stability, information content and corresponding full error budget evaluation. This has been done for the target species ozone (O3), methane (CH4), nitrous oxide (N2O), and carbon monoxide (CO). It is shown that the information operator approach performs well and is capable of achieving the same accuracy as optimal estimation, with a gain of stability and with the additional advantage of being less sensitive to the choice of a priori information as well as to the actual signal-to-noise ratio. Keywords: ground-based FTIR, solar absorption spectra, greenhouse gases, information operator approach References Doicu, A., Hilgers, S., von Bargen, A., Rozanov, A., Eichmann, K.-U., von Savigny, C., and Burrows, J.P.: Information operator approach and iterative regularization methods for atmospheric remote sensing, J. Quant. Spectrosc. Radiat. Transfer, 103, 340-350, 2007

Design of vertical thermosiphon reboilers for operation under vacuum conditions application in nuclear fuel reprocessing

International Nuclear Information System (INIS)

Moore, M.J.C.; Keys, M.H.; Plumb, G.R.

1988-01-01

Reprocessing of nuclear fuel requires concentration of uranium, plutonium and other active effluent streams at various stages for purification, storage or solidification. This is usually achieved by evaporation and in U.K. plant such processes are often carried out under reduced pressure. For high throughput streams, there are considerable advantages in using vertical thermosiphon systems for evaporation and for recovery of nitric acid. However, data for such systems at reduced pressure is limited and the development by John Brown E and C Ltd of a computer program for reliable prediction of thermosiphon performance was carried out on behalf of British Nuclear Fuels Plc using data from operating plant. (author)

A fast and zero-biased photodetector based on GaTe-InSe vertical 2D p-n heterojunction

Science.gov (United States)

Feng, W.; Jin, Z.; Yuan, J.; Zhang, J.; Jia, S.; Dong, L.; Yoon, J.; Zhou, L.; Vajtai, R.; Tour, J. M.; Ajayan, P. M.; Hu, P.; Lou, J.

2018-04-01

p-n junctions serve as the building blocks for fundamental semiconductor devices, such as solar cells, light-emitting diodes (LEDs) and photodetectors. With recent studies unveiling the excellent optoelectronic properties of two-dimensional (2D) semiconductors, they are considered to be superb candidates for high performance p-n junctions. Here, we fabricate a vertical GaTe-InSe van der Waals (vdWs) p-n heterojunction by a PDMS-assisted transfer technique without etching. The fabricated p-n heterojunction shows gate-tunable current-rectifying behavior with a rectification factor reaching 1000. In addition, it features fast photodetection under zero bias as well as a high power conversion efficiency (PCE). Under 405 nm laser excitation, the zero-biased photodetector shows a high responsivity of 13.8 mA W-1 as well as a high external quantum efficiency (EQE) of 4.2%. Long-term stability is also observed and a response time of 20 µs is achieved due to stable and fast carrier transit through the built-in electric field in the depletion region. Fast and efficient charge separation in the vertical 2D p-n junction paves the way for developing 2D photodetectors with zero dark current, high speed and low power consumption.

Damped oscillatory integrals and boundedness problem for maximal operators

International Nuclear Information System (INIS)

Ikromov, Isroil A.

2003-06-01

We consider a real-analytic hypersurface S in IR n+1 with surface measure dσ, ψ is a compactly supported non-negative smooth cut-off function, and we let dμ q be the surface measure with dμ q ψvertical barΛ(X)vertical bar q dσ, where Λ(X) is a damping factor defined by the matrix of a second fundamental form of the surface. We show that if S is a real analytic hypersurface, then μ-circumflex q (ξ) decays as O(vertical barξvertical bar -(1/2+ε) ), where ε > 0, provided q > 3/2. We also consider applications involving maximal operators associated to averages of functions over hypersurfaces. (author)

Vertical displacement events: a serious concern in future ITER operation

International Nuclear Information System (INIS)

Hassanein, A.; Sizyuk, T.; Ulrickson, M.

2007-01-01

The strongly elongated plasma configuration in ITER-like devices is vertically unstable unless an active control feedback at the vertical position is applied. A malfunction of this feedback system for variety of reasons can lead to a rapid plasma vertical displacement at full plasma current. As the plasma contacts the top or bottom of the vacuum vessel, the current is rapidly forced to zero, similar to the behavior of the plasma after the thermal quench of a disruption. This phenomenon constitutes the vertical displacement events (VDE). This can result in melting and vaporization of the plasma-facing component (PFC) as well as melting of the copper substrate and burnout of the coolant channels. The upgraded HEIGHTS simulation package is used to simulate in full 3D the response of an entire ITER module response to a VDE. The initial temperature distribution of the PFC and the bulk substrate prior to the VDE is calculated according to steady state heat flux, module design, and initial coolant temperature. The models used in the upgraded HEIGHTS were recently benchmarked against VDE simulation experiments using powerful electron beam and show an excellent agreement with the data.The surface temperature can then be very high and could result in significant melting of substrate copper and damage the coolant channels. In the case of Be surface, surface vaporization is quite high and will remove most incoming plasma power at typical ITER VDE condition. Therefore, the transmitted heat flux to the substrate and the coolant channels are low enough to cause any significant damage. However, if tungsten is exposed to the VDE the situation is quite different. No significant surface vaporization will occur at the tungsten surface thus, leaving the majority of the incident plasma power to be conducted to the copper substrate causing melting at the interface and burnout of coolant channel with serious implications on the integrity and subsequent performance of this module. The

Tensor product of left n-invertible operators

Czech Academy of Sciences Publication Activity Database

Duggal, B.P.; Müller, Vladimír

2013-01-01

Roč. 215, č. 2 (2013), s. 113-125 ISSN 0039-3223 R&D Projects: GA ČR GA201/09/0473 Institutional support: RVO:67985840 Keywords : Banach space * essentially left n- invertible operator * left n-invertible operator Subject RIV: BA - General Mathematics Impact factor: 0.630, year: 2013 http://journals.impan.pl/cgi-bin/doi?sm215-2-2

Vertically integrated, three-dimensional nanowire complementary metal-oxide-semiconductor circuits.

Science.gov (United States)

Nam, SungWoo; Jiang, Xiaocheng; Xiong, Qihua; Ham, Donhee; Lieber, Charles M

2009-12-15

Three-dimensional (3D), multi-transistor-layer, integrated circuits represent an important technological pursuit promising advantages in integration density, operation speed, and power consumption compared with 2D circuits. We report fully functional, 3D integrated complementary metal-oxide-semiconductor (CMOS) circuits based on separate interconnected layers of high-mobility n-type indium arsenide (n-InAs) and p-type germanium/silicon core/shell (p-Ge/Si) nanowire (NW) field-effect transistors (FETs). The DC voltage output (V(out)) versus input (V(in)) response of vertically interconnected CMOS inverters showed sharp switching at close to the ideal value of one-half the supply voltage and, moreover, exhibited substantial DC gain of approximately 45. The gain and the rail-to-rail output switching are consistent with the large noise margin and minimal static power consumption of CMOS. Vertically interconnected, three-stage CMOS ring oscillators were also fabricated by using layer-1 InAs NW n-FETs and layer-2 Ge/Si NW p-FETs. Significantly, measurements of these circuits demonstrated stable, self-sustained oscillations with a maximum frequency of 108 MHz, which represents the highest-frequency integrated circuit based on chemically synthesized nanoscale materials. These results highlight the flexibility of bottom-up assembly of distinct nanoscale materials and suggest substantial promise for 3D integrated circuits.

GaN-based vertical-cavity laser performance improvements using tunnel-junction-cascaded active regions

International Nuclear Information System (INIS)

Piprek, Joachim

2014-01-01

This Letter investigates the output power enhancement achieved by tunnel junction insertion into the InGaN multi-quantum well (MQW) active region of a 410 nm vertical-cavity surface-emitting laser which enables the repeated use of carriers for light generation (carrier recycling). While the number of quantum wells remains unchanged, the tunnel junction eliminates absorption caused by the non-uniform MQW carrier distribution. The thermal resistance drops and the excess bias lead to a surprisingly small rise in self-heating.

Unusual photoluminescence properties of vertically aligned InN nanorods grown by plasma-assisted molecular-beam epitaxy

International Nuclear Information System (INIS)

Shen, C.H.; Chen, H.Y.; Lin, H.W.; Wu, C.Y.; Gwo, S.; Klochikhin, A.A.; Davydov, V.Yu.

2007-01-01

We report the unusual photoluminescence (PL) properties of vertically aligned InN nanorod arrays grown on Si(111) with a Si 3 N 4 buffer layer. The optimum growth conditions of InN nanorods are obtained by controlling the III/V ratio and the growth temperature. Structural characterization by X-ray diffraction and scanning electron microscopy indicates that individual nanorods are wurtzite InN single crystals with the growth direction along the c-axis. Near-infrared PL from InN nanorods is clearly observed at room temperature. However, in comparison to the PL from InN epitaxial films, the PL from InN nanorods is significantly lower in efficiency and exhibit anomalous temperature dependence. We propose that these unusual PL properties are results of considerable structural disorder (especially for the low-temperature grown InN nanorods) and strong surface electron accumulation effect. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Effect of Plasma, RF, and RIE Treatments on Properties of Double-Sided High Voltage Solar Cells with Vertically Aligned p-n Junctions

Directory of Open Access Journals (Sweden)

Mykola O. Semenenko

2016-01-01

Full Text Available Si-based solar cells with vertically aligned p-n junctions operating at high voltage were designed and fabricated. The plasma treatments and antireflection coating deposition on the working surfaces of both single- and multijunction cells were made using the special holders. It was shown that additional treatment of solar cells in argon plasma prior to hydrogen plasma treatment and deposition of diamond-like carbon antireflection films led to the improvement of the cell efficiency by up to 60%. Radio frequency waves support plasma generation and improve photoelectric conversion mainly due to reduction of internal stresses at the interfaces. Application of reactive ion etching technique removes the broken layer, reduces elastic strain in the wafer, decreases recombination of charge carriers in the bulk, and provides cell efficiency increase by up to ten times.

Efecto de la intensidad del contramovimiento sobre el rendimiento del salto vertical

Directory of Open Access Journals (Sweden)

Marcos Gutiérrez-Dávila

2015-03-01

Full Text Available El propósito de esta investigación ha sido comprobar el efecto de la intensidad del contramovimiento sobre el rendimiento del salto vertical. Para el control de la intensidad se han utilizado tres protocolos de saltos verticales con participación de brazos: a saltos verticales partiendo desde la posición de erguidos (CMJ + S; b partiendo de un salto previo donde la altura de caída estaba regulada por el participante (DJ-AR, y c partiendo de un salto previo máximo (DJ-M. Han participado 28 deportistas practicantes de modalidades deportivas donde el salto vertical constituye una habilidad básica. Se ha utilizado una plataforma de fuerza, operando a 500 Hz, sincronizada temporalmente a una cámara de vídeo, que registraba a 210 Hz el plano sagital de los saltos realizados sobre la plataforma. La aceleración vertical del CM se determinó a partir de la fuerza neta vertical y la masa del saltador. A continuación, los sucesivos registros de la velocidad vertical y las posiciones de componente vertical adoptadas por el CM se determinaron mediante integración de las componentes verticales de las funciones de aceleración-tiempo y velocidad-tiempo, respectivamente. Las constantes de integración se determinaron mediante imágenes de vídeo (2D. Los resultados han puesto de manifiesto que, cuando se realizan saltos con alturas de caída superiores a 0,39 ± 0,05 m, el pico de potencia durante la fase propulsiva (PP(propulsiva, el impulso vertical de propulsión (Iv(propulsión., y la altura de salto (Ycm vuelo, se reducen de forma significativa (p < 0,001, lo que nos permite afirmar que se reduce el rendimiento durante la fase propulsiva.

Regional N2O fluxes in Amazonia derived from aircraft vertical profiles

Science.gov (United States)

D'Amelio, M. T. S.; Gatti, L. V.; Miller, J. B.; Tans, P.

2009-11-01

Nitrous oxide (N2O) is the third most important anthropogenic greenhouse gas. Globally, the main sources of N2O are nitrification and denitrification in soils. About two thirds of the soil emissions occur in the tropics and approximately 20% originate in wet rainforest ecosystems, like the Amazon forest. The work presented here involves aircraft vertical profiles of N2O from the surface to 4 km over two sites in the Eastern and Central Amazon: Tapajós National Forest (SAN) and Cuieiras Biologic Reserve (MAN), and the estimation of N2O fluxes for regions upwind of these sites. To our knowledge, these regional scale N2O measurements in Amazonia are unique and represent a new approach to looking regional scale emissions. The fluxes upwind of MAN exhibited little seasonality, and the annual mean was 2.1±1.0 mg N2O m-2 day-1, higher than that for fluxes upwind of SAN, which averaged 1.5±1.6 mg N2O m-2 day-1. The higher rainfall around the MAN site could explain the higher N2O emissions, as a result of increased soil moisture accelerating microbial nitrification and denitrification processes. For fluxes from the coast to SAN seasonality is present for all years, with high fluxes in the months of March through May, and in November through December. The first peak of N2O flux is strongly associated with the wet season. The second peak of high N2O flux recorded at SAN occurs during the dry season and can not be easily explained. However, about half of the dry season profiles exhibit significant correlations with CO, indicating a larger than expected source of N2O from biomass burning. The average CO:N2O ratio for all profiles sampled during the dry season is 94±77 mol CO:mol N2O and suggests a larger biomass burning contribution to the global N2O budget than previously reported.

Mutually unbiased bases and trinary operator sets for N qutrits

International Nuclear Information System (INIS)

Lawrence, Jay

2004-01-01

A compete orthonormal basis of N-qutrit unitary operators drawn from the Pauli group consists of the identity and 9 N -1 traceless operators. The traceless ones partition into 3 N +1 maximally commuting subsets (MCS's) of 3 N -1 operators each, whose joint eigenbases are mutually unbiased. We prove that Pauli factor groups of order 3 N are isomorphic to all MCS's and show how this result applies in specific cases. For two qutrits, the 80 traceless operators partition into 10 MCS's. We prove that 4 of the corresponding basis sets must be separable, while 6 must be totally entangled (and Bell-like). For three qutrits, 728 operators partition into 28 MCS's with less rigid structure, allowing for the coexistence of separable, partially entangled, and totally entangled (GHZ-like) bases. However a minimum of 16 GHZ-like bases must occur. Every basis state is described by an N-digit trinary number consisting of the eigenvalues of N observables constructed from the corresponding MCS

Essential spectra of difference operators on Zn-periodic graphs

International Nuclear Information System (INIS)

Rabinovich, Vladimir S; Roch, Steffen

2007-01-01

Let (X, ρ) be a discrete metric space. We suppose that the group Z n acts freely on X and that the number of orbits of X with respect to this action is finite. Then we call X a Z n -periodic discrete metric space. We examine the Fredholm property and essential spectra of band-dominated operators on l p (X) when 1 n and their limit operators. In the case where X is the set of vertices of a combinatorial graph, the graph structure defines a Schroedinger operator on l p (X) in a natural way. We illustrate our approach by determining the essential spectra of Schroedinger operators with slowly oscillating potential both on zig-zag and on hexagonal graphs, the latter being related to nano-structures

Evapotranspiration versus oxygen intrusion: which is the main force in alleviating bioclogging of vertical-flow constructed wetlands during a resting operation?

Science.gov (United States)

Hua, Guofen; Chen, Qiuwen; Kong, Jun; Li, Man

2017-08-01

Clogging is the most significant challenge limiting the application of constructed wetlands. Application of a forced resting period is a practical way to relieve clogging, particularly bioclogging. To reveal the alleviation mechanisms behind such a resting operation, evapotranspiration and oxygen flux were studied during a resting period in a laboratory vertical-flow constructed wetland model through physical simulation and numerical model analysis. In addition, the optimum theoretical resting duration was determined based on the time required for oxygen to completely fill the pores, i.e., formation of a sufficiently thick and completely dry layer. The results indicated that (1) evapotranspiration was not the key factor, but was a driving force in the alleviation of bioclogging; (2) the rate of oxygen diffusion into the pores was sufficient to oxidize and disperse the flocculant biofilm, which was essential to alleviate bioclogging. This study provides important insights into understanding how clogging/bioclogging can be alleviated in vertical-flow constructed wetlands. Graphical abstract Evapotranspiration versus oxygen intrusion in alleviating bioclogging in vertical flow constructed wetlands.

The su(2 vertical bar 3) dynamic spin chain

International Nuclear Information System (INIS)

Beisert, Niklas

2004-01-01

The complete one-loop, planar dilatation operator of the N=4 superconformal gauge theory was recently derived and shown to be integrable. Here, we present further compelling evidence for a generalisation of this integrable structure to higher orders of the coupling constant. For that we consider the su(2 vertical bar 3) subsector and investigate the restrictions imposed on the spin chain Hamiltonian by the symmetry algebra. This allows us to uniquely fix the energy shifts up to the three-loop level and thus prove the correctness of a conjecture in hep-th/0303060. A novel aspect of this spin chain model is that the higher-loop Hamiltonian, as for N=4 SYM in general, does not preserve the number of spin sites. Yet this dynamic spin chain appears to be integrable

POES Space Environment Monitor, Energetic Particles

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The TIROS/NOAA satellite series, also known as POES, is designed to meet the National Oceanic and Atmospheric Administration's need for operational, remote sensing...

Prevalencia de la desviación vertical disociada en pacientes con estrabismo secundario a mala visión versus estrabismo congénito con ambliopía

OpenAIRE

Pérez Pérez, José Fernando; Guido Jiménez, Marilú Anahí; Arroyo Yllanes, María Estela

2015-01-01

La desviación vertical disociada (DVD) se asocia a endotropía congénita; también se ha descrito en otros tipos de estrabismo como los secundarios. Objetivo: Establecer la frecuencia de DVD en pacientes con estrabismo secundario a mala visión. Material y método: Estudio prospectivo que incluyó a pacientes con estrabismo secundario a mala visión y como grupo control a pacientes con estrabismo y ambliopía estrábica profunda. Resultados: Se incluyeron 57 pacientes, el 77% fueron mujeres....

A measurement system for vertical seawater profiles close to the air-sea interface

Science.gov (United States)

Sims, Richard P.; Schuster, Ute; Watson, Andrew J.; Yang, Ming Xi; Hopkins, Frances E.; Stephens, John; Bell, Thomas G.

2017-09-01

This paper describes a near-surface ocean profiler, which has been designed to precisely measure vertical gradients in the top 10 m of the ocean. Variations in the depth of seawater collection are minimized when using the profiler compared to conventional CTD/rosette deployments. The profiler consists of a remotely operated winch mounted on a tethered yet free-floating buoy, which is used to raise and lower a small frame housing sensors and inlet tubing. Seawater at the inlet depth is pumped back to the ship for analysis. The profiler can be used to make continuous vertical profiles or to target a series of discrete depths. The profiler has been successfully deployed during wind speeds up to 10 m s-1 and significant wave heights up to 2 m. We demonstrate the potential of the profiler by presenting measured vertical profiles of the trace gases carbon dioxide and dimethylsulfide. Trace gas measurements use an efficient microporous membrane equilibrator to minimize the system response time. The example profiles show vertical gradients in the upper 5 m for temperature, carbon dioxide and dimethylsulfide of 0.15 °C, 4 µatm and 0.4 nM respectively.

Doppler Lidar Vertical Velocity Statistics Value-Added Product

Energy Technology Data Exchange (ETDEWEB)

Newsom, R. K. [DOE ARM Climate Research Facility, Washington, DC (United States); Sivaraman, C. [DOE ARM Climate Research Facility, Washington, DC (United States); Shippert, T. R. [DOE ARM Climate Research Facility, Washington, DC (United States); Riihimaki, L. D. [DOE ARM Climate Research Facility, Washington, DC (United States)

2015-07-01

Accurate height-resolved measurements of higher-order statistical moments of vertical velocity fluctuations are crucial for improved understanding of turbulent mixing and diffusion, convective initiation, and cloud life cycles. The Atmospheric Radiation Measurement (ARM) Climate Research Facility operates coherent Doppler lidar systems at several sites around the globe. These instruments provide measurements of clear-air vertical velocity profiles in the lower troposphere with a nominal temporal resolution of 1 sec and height resolution of 30 m. The purpose of the Doppler lidar vertical velocity statistics (DLWSTATS) value-added product (VAP) is to produce height- and time-resolved estimates of vertical velocity variance, skewness, and kurtosis from these raw measurements. The VAP also produces estimates of cloud properties, including cloud-base height (CBH), cloud frequency, cloud-base vertical velocity, and cloud-base updraft fraction.

Cut-and-join operators and N=4 super Yang-Mills

International Nuclear Information System (INIS)

Brown, T.W.

2010-02-01

We show which multi-trace structures are compatible with the symmetrisation of local operators in N=4 super Yang-Mills when they are organised into representations of the global symmetry group. Cut-and-join operators give the non-planar expansion of correlation functions of these operators in the free theory. Using these techniques we find the 1/N corrections to the quarter-BPS operators which remain protected at weak coupling. We also present a new way of counting these chiral ring operators using the Weyl group S N . (orig.)

Cut-and-join operators and N=4 super Yang-Mills

Energy Technology Data Exchange (ETDEWEB)

Brown, T W [DESY, Hamburg (Germany). Theory Group

2010-02-15

We show which multi-trace structures are compatible with the symmetrisation of local operators in N=4 super Yang-Mills when they are organised into representations of the global symmetry group. Cut-and-join operators give the non-planar expansion of correlation functions of these operators in the free theory. Using these techniques we find the 1/N corrections to the quarter-BPS operators which remain protected at weak coupling. We also present a new way of counting these chiral ring operators using the Weyl group S{sub N}. (orig.)

Structural reasons for vertical integration in the international oil industry

International Nuclear Information System (INIS)

Luciani, G.

1991-01-01

Once upon a time, the international oil industry was vertically integrated. A small group of companies controlled a very substantial share of international oil flows, extending their operations from the oil well to the gas pump, and relying on intracorporate transfers for most in-between transactions. The historical reasons for vertical disintegration, the market role, and structural reasons for vertical reintegration are examined. (author)

DISTRIBUCIÓN VERTICAL DE ARAÑAS ASOCIADAS A Quercus humboldtii Y Clusia spp. EN EL SANTUARIO DE FAUNA Y FLORA IGUAQUE, COLOMBIA

Directory of Open Access Journals (Sweden)

SILVIA VANEGAS

2012-09-01

Full Text Available Se estudió la distribución vertical de arañas asociadas a Quercus humboldtii y Clusia spp. en el Santuario de Fauna y Flora Iguaque, para esto se seleccionaron 10 árboles de cada género estratificándolos verticalmente cada 3m desde la base hasta el dosel. Se realizaron colectas en cada estrato por 20 min durante el día y en la noche. También se tomaron muestras en la parcela aledaña (4 m2. Se colectaron 1.261 individuos pertenecientes a 104 morfoespecies y 20 familias; las más frecuentes fueron Theridiidae, Salticidae, Araneidae, Linyphiidae, Anyphaenidae y Theridiosomatidae. Se encontraron diferencias en la distribución vertical de arañas en cuanto a la abundancia, riqueza, composición, distribución de sexos y épocas atribuibles a las arquitecturas vegetales y a su  estratificación. Clusia presentó la comunidad de arañas más diversa, Quercus la de mayor dominancia. La composición estuvo influida por las lluvias, el periodo del día y la disponibilidad de soportes vegetales.

Anomalous dimension of subleading-power N-jet operators

Science.gov (United States)

Beneke, Martin; Garny, Mathias; Szafron, Robert; Wang, Jian

2018-03-01

We begin a systematic investigation of the anomalous dimension of subleading power N-jet operators in view of resummation of logarithmically enhanced terms in partonic cross sections beyond leading power. We provide an explicit result at the one-loop order for fermion-number two N-jet operators at the second order in the power expansion parameter of soft-collinear effective theory.

Electrochemically synthesized visible light absorbing vertically aligned N-doped TiO2 nanotube array films

International Nuclear Information System (INIS)

Antony, Rajini P.; Mathews, Tom; Ajikumar, P.K.; Krishna, D. Nandagopala; Dash, S.; Tyagi, A.K.

2012-01-01

Graphical abstract: Display Omitted Highlights: ► Single step electrochemical synthesis of N-doped TiO 2 nanotube array films. ► Effective substitutional N-doping achieved. ► Different N-concentrations were achieved by varying the N-precursor concentration in the electrolyte. ► Visible light absorption observed at high N-doping. -- Abstract: Visible light absorbing vertically aligned N-doped anatase nanotube array thin films were synthesized by anodizing Ti foils in ethylene glycol + NH 4 F + water mixture containing urea as nitrogen source. Different nitrogen concentrations were achieved by varying the urea content in the electrolyte. The structure, morphology, composition and optical band gap of the nanotube arrays were determined by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy (XPS) and diffuse reflectance spectroscopy, respectively. The substitution of O 2− ions by N 3− ions in the anion sublattice as well as the formulae of the doped samples was confirmed from the results of XPS. The optical band gap of the nanotube arrays was found to decrease with N-concentration. The sample with the highest concentration corresponding to the formula TiO 1.83 N 0.14 showed two regions in the Tauc's plot indicating the presence of interband states.

Vestibulo-Ocular Responses to Vertical Translation using a Hand-Operated Chair as a Field Measure of Otolith Function

Science.gov (United States)

Wood, S. J.; Campbell, D. J.; Reschke, M. F.; Prather, L.; Clement, G.

2016-01-01

The translational Vestibulo-Ocular Reflex (tVOR) is an important otolith-mediated response to stabilize gaze during natural locomotion. One goal of this study was to develop a measure of the tVOR using a simple hand-operated chair that provided passive vertical motion. Binocular eye movements were recorded with a tight-fitting video mask in ten healthy subjects. Vertical motion was provided by a modified spring-powered chair (swopper.com) at approximately 2 Hz (+/- 2 cm displacement) to approximate the head motion during walking. Linear acceleration was measured with wireless inertial sensors (Xsens) mounted on the head and torso. Eye movements were recorded while subjects viewed near (0.5m) and far (approximately 4m) targets, and then imagined these targets in darkness. Subjects also provided perceptual estimates of target distances. Consistent with the kinematic properties shown in previous studies, the tVOR gain was greater with near targets, and greater with vision than in darkness. We conclude that this portable chair system can provide a field measure of otolith-ocular function at frequencies sufficient to elicit a robust tVOR.

Performance of hybrid p-type vertical transistors with poly(N-vinylcarbazole) as emitter and the transfer mechanism of charge carriers through the base

International Nuclear Information System (INIS)

Huang, Jinying; Ma, Dongge; Hümmelgen, Ivo A

2013-01-01

We report hybrid vertical architecture p-type transistors with poly(N-vinylcarbazole) as the emitter, p-type silicon as the collector and Al:Ca alloy layer as the base. The investigation of the common-base and common-emitter characteristics clearly demonstrates that the devices operate as permeable-base transistors (PBTs). The PBTs show common-base current gain α of 0.98 at −V BC = 1.5 V and common-emitter gain β of over 100. Atomic force microscope images of the base layer show an uneven surface, showing that the annealing does not dissolve the charge trap states but offers ‘pinholes’ for the oxidation in-depth even through the whole base layer. In this case, the charge carriers must tunnel the thin oxidized layer, and then are collected. It is clearly seen that there exists a barrier against holes injection from the base to the collector semiconductor at the interface, and the further oxidation caused by exposing the devices in air changes the operational mode of the resulting devices from the PBT to the metal-base transistor. (paper)

A self-decoupling piezoresistive sensor for measuring microforce in horizontal and vertical directions

International Nuclear Information System (INIS)

Zhou, Jie; Rong, Weibin; Wang, Lefeng; Gao, Peng; Sun, Lining

2016-01-01

This paper presents the design, fabrication and calibration of a novel two-dimension microforce sensor with nano-Newton resolution. The sensor, mainly composed of a clamped–clamped beam (horizontal detecting beam), an overhanging beam (vertical detecting beam) and a half-folded beam, is highly sensitive to microforces in the horizontal (parallel to the probe of the designed sensor) and vertical (perpendicular to the wafer surface) directions. The four vertical sidewall surface piezoresistors (horizontal piezoresistors) and two surface piezoresistors (vertical piezoresistors) were fabricated to achieve the requirements of two-dimension microforce measurements. Combining the sensor structure with Wheatstone bridge configurations, the microforce decoupling among the x , y , and z direction can be realized. Accordingly, the sensor is capable of detecting microforces in the horizontal and vertical directions independently. The calibration results verified that the sensor sensitivities at room temperature are 210.58 V N −1 and 159.2 V N −1 in the horizontal and vertical directions, respectively. Additionally, the sensor’s corresponding force resolutions are estimated at 2 nN and 3 nN in theory, respectively. The sensor can be used to measure the contact force between manipulating tools and micro-objects, in fields such as microassembly and biological assays. (paper)

High-Performance Schottky Diode Gas Sensor Based on the Heterojunction of Three-Dimensional Nanohybrids of Reduced Graphene Oxide-Vertical ZnO Nanorods on an AlGaN/GaN Layer.

Science.gov (United States)

Minh Triet, Nguyen; Thai Duy, Le; Hwang, Byeong-Ung; Hanif, Adeela; Siddiqui, Saqib; Park, Kyung-Ho; Cho, Chu-Young; Lee, Nae-Eung

2017-09-13

A Schottky diode based on a heterojunction of three-dimensional (3D) nanohybrid materials, formed by hybridizing reduced graphene oxide (RGO) with epitaxial vertical zinc oxide nanorods (ZnO NRs) and Al 0.27 GaN 0.73 (∼25 nm)/GaN is presented as a new class of high-performance chemical sensors. The RGO nanosheet layer coated on the ZnO NRs enables the formation of a direct Schottky contact with the AlGaN layer. The sensing results of the Schottky diode with respect to NO 2 , SO 2 , and HCHO gases exhibit high sensitivity (0.88-1.88 ppm -1 ), fast response (∼2 min), and good reproducibility down to 120 ppb concentration levels at room temperature. The sensing mechanism of the Schottky diode can be explained by the effective modulation of the reverse saturation current due to the change in thermionic emission carrier transport caused by ultrasensitive changes in the Schottky barrier of a van der Waals heterostructure between RGO and AlGaN layers upon interaction with gas molecules. Advances in the design of a Schottky diode gas sensor based on the heterojunction of high-mobility two-dimensional electron gas channel and highly responsive 3D-engineered sensing nanomaterials have potential not only for the enhancement of sensitivity and selectivity but also for improving operation capability at room temperature.

Climate Prediction Center (CPC)Stratospheric Monitoring Ozone Blended Analysis

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — A 3-D global ozone mixing ratio (ppm) and total column ozone (DU) dataset analyzed from daily Solar Backscatter Ultraviolet Instrument(SBUV/2) and TIROS Operational...

Operation of a novel hot-electron vertical-cavity surface-emitting laser

Science.gov (United States)

Balkan, Naci; O'Brien-Davies, Angela; Thoms, A. B.; Potter, Richard J.; Poolton, Nigel; Adams, Michael J.; Masum, J.; Bek, Alpan; Serpenguzel, Ali; Aydinli, Atilla; Roberts, John S.

1998-07-01

The hot Electron Light Emission and Lasing in Semiconductor Heterostructures devices (HELLISH-1) is novel surface emitter consisting of a GaAs quantum well, within the depletion region, on the n side of Ga1-xAlxAs p- n junction. It utilizes hot electron transport parallel to the layers and injection of hot electron hole pairs into the quantum well through a combination of mechanisms including tunnelling, thermionic emission and diffusion of `lucky' carriers. Super Radiant HELLISH-1 is an advanced structure incorporating a lower distributed Bragg reflector (DBR). Combined with the finite reflectivity of the upper semiconductor-air interface reflectivity it defines a quasi- resonant cavity enabling emission output from the top surface with a higher spectral purity. The output power has increased by two orders of magnitude and reduced the full width at half maximum (FWHM) to 20 nm. An upper DBR added to the structure defines HELLISH-VCSEL which is currently the first operational hot electron surface emitting laser and lases at room temperature with a 1.5 nm FWHM. In this work we demonstrate and compare the operation of UB-HELLISH-1 and HELLISH-VCSEL using experimental and theoretical reflectivity spectra over an extensive temperature range.

Profiles of CH4, HDO, H2O, and N2O with improved lower tropospheric vertical resolution from Aura TES radiances

Directory of Open Access Journals (Sweden)

D. Noone

2012-02-01

Full Text Available Thermal infrared (IR radiances measured near 8 microns contain information about the vertical distribution of water vapor (H2O, the water isotopologue HDO, and methane (CH4, key gases in the water and carbon cycles. Previous versions (Version 4 or less of the TES profile retrieval algorithm used a "spectral-window" approach to minimize uncertainty from interfering species at the expense of reduced vertical resolution and sensitivity. In this manuscript we document changes to the vertical resolution and uncertainties of the TES version 5 retrieval algorithm. In this version (Version 5, joint estimates of H2O, HDO, CH4 and nitrous oxide (N2O are made using radiances from almost the entire spectral region between 1100 cm−1 and 1330 cm−1. The TES retrieval constraints are also modified in order to better use this information. The new H2O estimates show improved vertical resolution in the lower troposphere and boundary layer, while the new HDO/H2O estimates can now profile the HDO/H2O ratio between 925 hPa and 450 hPa in the tropics and during summertime at high latitudes. The new retrievals are now sensitive to methane in the free troposphere between 800 and 150 mb with peak sensitivity near 500 hPa; whereas in previous versions the sensitivity peaked at 200 hPa. However, the upper troposphere methane concentrations are biased high relative to the lower troposphere by approximately 4% on average. This bias is likely related to temperature, calibration, and/or methane spectroscopy errors. This bias can be mitigated by normalizing the CH4 estimate by the ratio of the N2O estimate relative to the N2O prior, under the assumption that the same systematic error affects both the N2O and CH4 estimates. We demonstrate that applying this ratio theoretically reduces the CH4 estimate for non-retrieved parameters that jointly affect both the N2O and CH4 estimates. The relative upper troposphere to lower troposphere bias is approximately 2.8% after this bias

Breakwaters with Vertical and Inclined Concrete Walls

DEFF Research Database (Denmark)

Burcharth, Hans Falk

Following the PIANC PTC II working group on Analyses of Rubble Mound Breakwaters it was, in 1991, decided to form Working Group (WG) n° 28 on "Breakwaters with vertical and inclined concrete walls" The scope of the work was to achieve a better understanding of the overall safety aspects in the de......Following the PIANC PTC II working group on Analyses of Rubble Mound Breakwaters it was, in 1991, decided to form Working Group (WG) n° 28 on "Breakwaters with vertical and inclined concrete walls" The scope of the work was to achieve a better understanding of the overall safety aspects...

Determinations of vertical stroke V{sub cb} vertical stroke and vertical stroke V{sub ub} vertical stroke from baryonic Λ{sub b} decays

Energy Technology Data Exchange (ETDEWEB)

Hsiao, Y.K. [Shanxi Normal University, School of Physics and Information Engineering, Linfen (China); National Tsing Hua University, Department of Physics, Hsinchu (China); Geng, C.Q. [Shanxi Normal University, School of Physics and Information Engineering, Linfen (China); National Tsing Hua University, Department of Physics, Hsinchu (China); Hunan Normal University, Synergetic Innovation Center for Quantum Effects and Applications (SICQEA), Changsha (China)

2017-10-15

We present the first attempt to extract vertical stroke V{sub cb} vertical stroke from the Λ{sub b} → Λ{sub c}{sup +}l anti ν{sub l} decay without relying on vertical stroke V{sub ub} vertical stroke inputs from the B meson decays. Meanwhile, the hadronic Λ{sub b} → Λ{sub c}M{sub (c)} decays with M = (π{sup -},K{sup -}) and M{sub c} =(D{sup -},D{sup -}{sub s}) measured with high precisions are involved in the extraction. Explicitly, we find that vertical stroke V{sub cb} vertical stroke =(44.6 ± 3.2) x 10{sup -3}, agreeing with the value of (42.11 ± 0.74) x 10{sup -3} from the inclusive B → X{sub c}l anti ν{sub l} decays. Furthermore, based on the most recent ratio of vertical stroke V{sub ub} vertical stroke / vertical stroke V{sub cb} vertical stroke from the exclusive modes, we obtain vertical stroke V{sub ub} vertical stroke = (4.3 ± 0.4) x 10{sup -3}, which is close to the value of (4.49 ± 0.24) x 10{sup -3} from the inclusive B → X{sub u}l anti ν{sub l} decays. We conclude that our determinations of vertical stroke V{sub cb} vertical stroke and vertical stroke V{sub ub} vertical stroke favor the corresponding inclusive extractions in the B decays. (orig.)

Gallium nitride vertical power devices on foreign substrates: a review and outlook

Science.gov (United States)

Zhang, Yuhao; Dadgar, Armin; Palacios, Tomás

2018-07-01

Vertical gallium nitride (GaN) power devices have attracted increased attention due to their superior high-voltage and high-current capacity as well as easier thermal management than lateral GaN high electron mobility transistors. Vertical GaN devices are promising candidates for next-generation power electronics in electric vehicles, data centers, smart grids and renewable energy process. The use of low-cost foreign substrates such as silicon (Si) substrates, instead of the expensive free-standing GaN substrates, could greatly trim material cost and enable large-diameter wafer processing while maintaining high device performance. This review illustrates recent progress in material epitaxy, device design, device physics and processing technologies for the development of vertical GaN power devices on low-cost foreign substrates. Although the device technologies are still at the early stage of development, state-of-the-art vertical GaN-on-Si power diodes have already shown superior Baliga’s figure of merit than commercial SiC and Si power devices at the voltage classes beyond 600 V. Furthermore, we unveil the design space of vertical GaN power devices on native and different foreign substrates, from the analysis of the impact of dislocation and defects on device performance. We conclude by identifying the application space, current challenges and exciting research opportunities in this very dynamic research field.

Piezoelectric polarization and quantum size effects on the vertical transport in AlGaN/GaN resonant tunneling diodes

International Nuclear Information System (INIS)

Dakhlaoui, H; Almansour, S

2016-01-01

In this work, the electronic properties of resonant tunneling diodes (RTDs) based on GaN-Al x Ga (1−x) N double barriers are investigated by using the non-equilibrium Green functions formalism (NEG). These materials each present a wide conduction band discontinuity and a strong internal piezoelectric field, which greatly affect the electronic transport properties. The electronic density, the transmission coefficient, and the current–voltage characteristics are computed with considering the spontaneous and piezoelectric polarizations. The influence of the quantum size on the transmission coefficient is analyzed by varying GaN quantum well thickness, Al x Ga (1−x) N width, and the aluminum concentration x Al . The results show that the transmission coefficient more strongly depends on the thickness of the quantum well than the barrier; it exhibits a series of resonant peaks and valleys as the quantum well width increases. In addition, it is found that the negative differential resistance (NDR) in the current–voltage ( I – V) characteristic strongly depends on aluminum concentration x Al . It is shown that the peak-to-valley ratio (PVR) increases with x Al value decreasing. These findings open the door for developing vertical transport nitrides-based ISB devices such as THz lasers and detectors. (paper)

Requerimientos de Energía en Operaciones de Labranza con Implementos de Discos

Directory of Open Access Journals (Sweden)

Rincón C. Carlos J.

1985-12-01

Full Text Available Este trabajo trata de establecer lo siguiente: Determinar los requerimientos de fuerza de tiro y potencia en operaciones de arado y desterronamiento con implementos de discos. Establecer los rangos de humedad del suelo y velocidad de aplicación del implemento para suelos de diferentes texturas con el fin de obtener un nuevo aprovechamiento de la fuente de potencia. Con base en los datos de campo, establecer mediante modelos matemáticos las relaciones existentes entre la fuerza de tiro y su respectiva potencia con los parámetros de humedad del suelo y velocidad de operación del implemento. A pesar del uso intensivo de estos equipos en operaciones de labranza, aún no se han hecho estudios a nivel nacional del comportamiento de los mismos para las diferentes condiciones de suelos en épocas de preparación. En términos generales se encontró que en la arada, para suelos de textura fina (pesados hay una tendencia más pronunciada al incremento en la fuerza de tiro a medida que aumenta la humedad del suelo, que en los suelos moderadamente pesados y en los livianos. En el caso de los rastrillos las diferencias en el comportamiento son menos pronunciadas. Con el objeto de obtener una relación matemática entre las variables se analizaron varios modelos matemáticos de los cuales el que presentó un mayor ajuste fue: Ln F= b0 + b1 Lm V donde: F= Fuerza de tiro por unidad de ancho (KN /m V= Velocidad de operación (mI S b0 y b1 = Coeficientes de regresión. La relación correspondiente para potencia requerida en las operaciones de la labranza fue: Lm P = b2 + b3 L m V. donde: P = Potencia por unidad de ancho (KW/m. Para la resistencia unitaria al corte en el caso de los arados la relación correspondiente fue: Lm R = b4 + b5 Lm V donde: R= Resistencia unitaria al corte (KN/m 2 .

Influence of changing the distance of the 3-point line in basketball

Directory of Open Access Journals (Sweden)

Antonio Montero

2013-01-01

Full Text Available Los objetivos del presente estudio fueron: 1 comprobar la influencia de la modificación de la distancia en la línea que delimita el triple (de 6.25 a 6.75 metros sobre el porcentaje de acierto en los tiros de 3 puntos, durante los partidos de liga regular y playoff y 2 determinar si dicha modificación influye en la cantidad de tiros realizados por los diferentes puestos específicos en baloncesto (base, escolta, alero, ala pívot y pívot, así como en el porcentaje de acierto. Los datos se obtuvieron de la web oficial de la ACB (www.acb.com e incluyen todos los partidos de la liga regular y del playoff jugados durante las temporadas 2009-2010 (n = 290 partidos y 7185 lanzamientos de 3 puntos y 2010-2011 (n = 288 partidos y 6145 lanzamientos de 3 puntos; registrando, únicamente, a los jugadores que participaron ambas temporadas en dicha competición en elmismo equipo (n = 115. Los principales resultados indican que el número de tiros de 3 realizados en la temporada 2009/2010 es superior a los realizados en la temporada siguiente, 2010/2011, en la que se retrasa la línea que delimita el triple. Se puede apreciar, en la comparación de ambas temporadas, la existencia de diferencias estadísticamente significativas entre aleros por el número de lanzamientos intentados, entre todos los puestos por el número de lanzamientos convertidos y entre escoltas en los porcentajes de acierto del conjunto del equipo; diferencias que no se manifiestan en los partidos de playoff.

A measurement system for vertical seawater profiles close to the air–sea interface

Directory of Open Access Journals (Sweden)

R. P. Sims

2017-09-01

Full Text Available This paper describes a near-surface ocean profiler, which has been designed to precisely measure vertical gradients in the top 10 m of the ocean. Variations in the depth of seawater collection are minimized when using the profiler compared to conventional CTD/rosette deployments. The profiler consists of a remotely operated winch mounted on a tethered yet free-floating buoy, which is used to raise and lower a small frame housing sensors and inlet tubing. Seawater at the inlet depth is pumped back to the ship for analysis. The profiler can be used to make continuous vertical profiles or to target a series of discrete depths. The profiler has been successfully deployed during wind speeds up to 10 m s−1 and significant wave heights up to 2 m. We demonstrate the potential of the profiler by presenting measured vertical profiles of the trace gases carbon dioxide and dimethylsulfide. Trace gas measurements use an efficient microporous membrane equilibrator to minimize the system response time. The example profiles show vertical gradients in the upper 5 m for temperature, carbon dioxide and dimethylsulfide of 0.15 °C, 4 µatm and 0.4 nM respectively.

Barrier reduction via implementation of InGaN interlayer in wafer-bonded current aperture vertical electron transistors consisting of InGaAs channel and N-polar GaN drain

International Nuclear Information System (INIS)

Kim, Jeonghee; Laurent, Matthew A.; Li, Haoran; Lal, Shalini; Mishra, Umesh K.

2015-01-01

This letter reports the influence of the added InGaN interlayer on reducing the inherent interfacial barrier and hence improving the electrical characteristics of wafer-bonded current aperture vertical electron transistors consisting of an InGaAs channel and N-polar GaN drain. The current-voltage characteristics of the transistors show that the implementation of N-polar InGaN interlayer effectively reduces the barrier to electron transport across the wafer-bonded interface most likely due to its polarization induced downward band bending, which increases the electron tunneling probability. Fully functional wafer-bonded transistors with nearly 600 mA/mm of drain current at V GS  = 0 V and L go  = 2 μm have been achieved, and thus demonstrate the feasibility of using wafer-bonded heterostructures for applications that require active carrier transport through both materials

Functionalized vertical GaN micro pillar arrays with high signal-to-background ratio for detection and analysis of proteins secreted from breast tumor cells.

Science.gov (United States)

Choi, Mun-Ki; Kim, Gil-Sung; Jeong, Jin-Tak; Lim, Jung-Taek; Lee, Won-Yong; Umar, Ahmad; Lee, Sang-Kwon

2017-11-02

The detection of cancer biomarkers has recently attracted significant attention as a means of determining the correct course of treatment with targeted therapeutics. However, because the concentration of these biomarkers in blood is usually relatively low, highly sensitive biosensors for fluorescence imaging and precise detection are needed. In this study, we have successfully developed vertical GaN micropillar (MP) based biosensors for fluorescence sensing and quantitative measurement of CA15-3 antigens. The highly ordered vertical GaN MP arrays result in the successful immobilization of CA15-3 antigens on each feature of the arrays, thereby allowing the detection of an individual fluorescence signal from the top surface of the arrays owing to the high regularity of fluorophore-tagged MP spots and relatively low background signal. Therefore, our fluorescence-labeled and CA15-3 functionalized vertical GaN-MP-based biosensor is suitable for the selective quantitative analysis of secreted CA15-3 antigens from MCF-7 cell lines, and helps in the early diagnosis and prognosis of serious diseases as well as the monitoring of the therapeutic response of breast cancer patients.

Measurement of Cabbibo-suppressed τ lepton decays and the determination of vertical stroke Vus vertical stroke

International Nuclear Information System (INIS)

Schenk, Stefan

2008-01-01

This work presents simultaneous branching fraction measurements of the decay modes τ - →K - nπ 0 ν τ with n=0,1,2,3 and τ - →π - nπ 0 ν τ with n=3,4. The analysis is based on a data sample of 427 x 10 6 τ + τ - pairs recorded with the BABAR detector, which corresponds to an integrated luminosity of 464.4 fb -1 . The measured values are B(τ - →K - ν τ )=(6.57±0.03±0.11) x 10 -3 , B(τ - →K - π 0 ν τ )=(4.61±0.03±0.11) x 10 -3 , B(τ - →K - π 0 π 0 ν τ )=(5.05±0.17±0.44) x 10 -4 , B(τ - →K - π 0 π 0 π 0 ν τ )=(1.31±0.43±0.40) x 10 -4 , B(τ - →π - π 0 π 0 π 0 ν τ )=(1.263±0.008±0.078) x 10 -2 and B(τ - →π - π 0 π 0 π 0 π 0 ν τ )=(9.6±0.5±1.2) x 10 -4 , where the uncertainties are statistical and systematic, respectively. All measurements are compatible with the current world averages whereas the uncertainties are significantly smaller by a factor of up to five. The determination of B(τ - →π - π 0 π 0 π 0 π 0 ν τ ) is the first measurement of this branching fraction. The measured branching fractions are combined with the current world averages. Using the new averages, an updated determination of vertical stroke V us vertical stroke from hadronic τ decays yields vertical stroke V us vertical stroke =0.2146±0.0025, which improves previous measurements by 19%. Its uncertainty is comparable to the one of the current world average from semileptonic kaon decays. (orig.)

On the ability of chemical transport models to simulate the vertical structure of the N2O, NO2 and HNO3 species in the mid-latitude stratosphere

Directory of Open Access Journals (Sweden)

G. Berthet

2006-01-01

Full Text Available In this paper we study the impact of the modelling of N2O on the simulation of NO2 and HNO3 by comparing in situ vertical profiles measured at mid-latitudes with the results of the Reprobus 3-D CTM (Three-dimensional Chemical Transport Model computed with the kinetic parameters from the JPL recommendation in 2002. The analysis of the measured in situ profile of N2O shows particular features indicating different air mass origins. The measured N2O, NO2 and HNO3 profiles are not satisfyingly reproduced by the CTM when computed using the current 6-hourly ECMWF operational analysis. Improving the simulation of N2O transport allows us to calculate quantities of NO2 and HNO3 in reasonable agreement with observations. This is achieved using 3-hourly winds obtained from ECMWF forecasts. The best agreement is obtained by constraining a one-dimensional version of the model with the observed N2O. This study shows that the modelling of the NOy partitioning with better accuracy relies at least on a correct simulation of N2O and thus of total NOy.

Thermal Stratification in Vertical Mantle Tanks

DEFF Research Database (Denmark)

Knudsen, Søren; Furbo, Simon

2001-01-01

It is well known that it is important to have a high degree of thermal stratification in the hot water storage tank to achieve a high thermal performance of SDHW systems. This study is concentrated on thermal stratification in vertical mantle tanks. Experiments based on typical operation conditions...... are carried out to investigate how the thermal stratification is affected by different placements of the mantle inlet. The heat transfer between the solar collector fluid in the mantle and the domestic water in the inner tank is analysed by CFD-simulations. Furthermore, the flow pattern in the vertical mantle...

Asymmetric SOL Current in Vertically Displaced Plasma

Science.gov (United States)

Cabrera, J. D.; Navratil, G. A.; Hanson, J. M.

2017-10-01

Experiments at the DIII-D tokamak demonstrate a non-monotonic relationship between measured scrape-off layer (SOL) currents and vertical displacement event (VDE) rates with SOL currents becoming largely n=1 dominant as plasma is displaced by the plasma control system (PCS) at faster rates. The DIII-D PCS is used to displace the magnetic axis 10x slower than the intrinsic growth time of similar instabilities in lower single-null plasmas. Low order (n VDE instabilities observed when vertical control is disabled. Previous inquiry shows VDE asymmetry characterized by SOL current fraction and geometric parameters of tokamak plasmas. We note that, of plasmas displaced by the PCS, short displacement time scales near the limit of the PCS temporal control appear to result in larger n=1/n=2 asymmetries. Work supported under USDOE Cooperative Agreement DE-FC02-04ER54698 and DE-FG02-04ER54761.

Vertical organic transistors

International Nuclear Information System (INIS)

Lüssem, Björn; Günther, Alrun; Fischer, Axel; Kasemann, Daniel; Leo, Karl

2015-01-01

Organic switching devices such as field effect transistors (OFETs) are a key element of future flexible electronic devices. So far, however, a commercial breakthrough has not been achieved because these devices usually lack in switching speed (e.g. for logic applications) and current density (e.g. for display pixel driving). The limited performance is caused by a combination of comparatively low charge carrier mobilities and the large channel length caused by the need for low-cost structuring. Vertical Organic Transistors are a novel technology that has the potential to overcome these limitations of OFETs. Vertical Organic Transistors allow to scale the channel length of organic transistors into the 100 nm regime without cost intensive structuring techniques. Several different approaches have been proposed in literature, which show high output currents, low operation voltages, and comparatively high speed even without sub-μm structuring technologies. In this review, these different approaches are compared and recent progress is highlighted. (topical review)

Vertical organic transistors.

Science.gov (United States)

Lüssem, Björn; Günther, Alrun; Fischer, Axel; Kasemann, Daniel; Leo, Karl

2015-11-11

Organic switching devices such as field effect transistors (OFETs) are a key element of future flexible electronic devices. So far, however, a commercial breakthrough has not been achieved because these devices usually lack in switching speed (e.g. for logic applications) and current density (e.g. for display pixel driving). The limited performance is caused by a combination of comparatively low charge carrier mobilities and the large channel length caused by the need for low-cost structuring. Vertical Organic Transistors are a novel technology that has the potential to overcome these limitations of OFETs. Vertical Organic Transistors allow to scale the channel length of organic transistors into the 100 nm regime without cost intensive structuring techniques. Several different approaches have been proposed in literature, which show high output currents, low operation voltages, and comparatively high speed even without sub-μm structuring technologies. In this review, these different approaches are compared and recent progress is highlighted.

Waveguide-integrated vertical pin photodiodes of Ge fabricated on p+ and n+ Si-on-insulator layers

Science.gov (United States)

Ito, Kazuki; Hiraki, Tatsurou; Tsuchizawa, Tai; Ishikawa, Yasuhiko

2017-04-01

Vertical pin structures of Ge photodiodes (PDs) integrated with Si optical waveguides are fabricated by depositing Ge epitaxial layers on Si-on-insulator (SOI) layers, and the performances of n+-Ge/i-Ge/p+-SOI PDs are compared with those of p+-Ge/i-Ge/n+-SOI PDs. Both types of PDs show responsivities as high as 1.0 A/W at 1.55 µm, while the dark leakage current is different, which is consistent with previous reports on free-space PDs formed on bulk Si wafers. The dark current of the p+-Ge/i-Ge/n+-SOI PDs is higher by more than one order of magnitude. Taking into account the activation energies for dark current as well as the dependence on PD area, the dark current of the n+-Ge/i-Ge/p+-SOI PDs is dominated by the thermal generation of carriers via mid-gap defect levels in Ge, while for the p+-Ge/i-Ge/n+-SOI PDs, the dark current is ascribed to not only thermal generation but also other mechanisms such as locally formed conduction paths.

On operator mixing in N=4 SYM

International Nuclear Information System (INIS)

Bianchi, Massimo; Eden, Burkhard; Rossi, Giancarlo; Stanev, Yassen S.

2002-01-01

We resolve the mixing of the scalar operators of naive dimension 4 belonging to the representation 20' of the SU(4) R-symmetry in N=4 SYM. We compute the order g 2 corrections to their anomalous dimensions and show the absence of instantonic contributions thereof. Ratios of the resulting expressions are irrational numbers, even in the large N limit where, however, we observe the expected decoupling of double-trace operators from single-trace ones. We briefly comment on the generalizations of our results required in order to make contact with the double scaling limit of the theory conjectured to be holographically dual to type IIB superstring on a pp-wave

A search for thermospheric composition perturbations due to vertical winds

Science.gov (United States)

Krynicki, Matthew P.

The thermosphere is generally in hydrostatic equilibrium, with winds blowing horizontally along stratified constant-pressure surfaces, driven by the dayside-to-nightside pressure gradient. A marked change in this paradigm resulted after Spencer et al. [1976] reported vertical wind measurements of 80 m·s-1 from analyses of AE-C satellite data. It is now established that the thermosphere routinely supports large-magnitude (˜30-150 m·s-1) vertical winds at auroral latitudes. These vertical winds represent significant departure from hydrostatic and diffusive equilibrium, altering locally---and potentially globally---the thermosphere's and ionosphere's composition, chemistry, thermodynamics and energy budget. Because of their localized nature, large-magnitude vertical wind effects are not entirely known. This thesis presents ground-based Fabry-Perot Spectrometer OI(630.0)-nm observations of upper-thermospheric vertical winds obtained at Inuvik, NT, Canada and Poker Flat, AK. The wind measurements are compared with vertical displacement estimates at ˜104 km2 horizontal spatial scales determined from a new modification to the electron transport code of Lummerzheim and Lilensten [1994] as applied to FUV-wavelength observations by POLAR spacecraft's Ultraviolet Imager [Torr et al. , 1995]. The modification, referred to as the column shift, simulates vertical wind effects such as neutral transport and disruption of diffusive equilibrium by vertically displacing the Hedin [1991] MSIS-90 [O2]/[N2] and [O]/([N2]+[O2]) mixing ratios and subsequently redistributing the O, O2, and N 2 densities used in the transport code. Column shift estimates are inferred from comparisons of UVI OI(135.6)-nm auroral observations to their corresponding modeled emission. The modeled OI(135.6)-nm brightness is determined from the modeled thermospheric response to electron precipitation and estimations of the energy flux and characteristic energy of the precipitation, which are inferred from UVI

Vertical Cavity Surface Emitting Laser for Operation at 1.5 µm with Integral AlGaInAs/InP Bragg mirrors

OpenAIRE

Linnik, M.; Christou, A.

2001-01-01

The design and performance of a low threshold selectively oxidized Vertical Cavity Surface Emitting Laser (VCSEL) fabricated for operation at a wavelength of 1.55 µm is based on III-V quaternary semiconductor alloys and is grown by Molecular Beam Epitaxy technique. The theoretical investigation of the optical properties of the compound semiconductor alloys allows one to select the optimum materials for highly reflective Bragg mirrors. The simulation of the designed VCSEL performance has been ...

Fast pulsing dynamics of a vertical-cavity surface-emitting laser operating in the low-frequency fluctuation regime

International Nuclear Information System (INIS)

Sciamanna, M.; Rogister, F.; Megret, P.; Blondel, M.; Masoller, C.; Abraham, N. B.

2003-01-01

We analyze the dynamics of a vertical-cavity surface-emitting laser with optical feedback operating in the low-frequency fluctuation regime. By focusing on the fast pulsing dynamics, we show that the two linearly polarized modes of the laser exhibit two qualitatively different behaviors: they emit pulses in phase just after a power dropout and they emit pulses out of phase after the recovery process of the output power. As a consequence, two distinct statistical distributions of the fast pulsating total intensity are observed, either monotonically decaying from the noise level or peaked around the mean intensity value. We further show that gain self-saturation of the lasing transition strongly modifies the shape of the intensity distribution

Low-voltage organic electronics based on a gate-tunable injection barrier in vertical graphene-organic semiconductor heterostructures.

Science.gov (United States)

Hlaing, Htay; Kim, Chang-Hyun; Carta, Fabio; Nam, Chang-Yong; Barton, Rob A; Petrone, Nicholas; Hone, James; Kymissis, Ioannis

2015-01-14

The vertical integration of graphene with inorganic semiconductors, oxide semiconductors, and newly emerging layered materials has recently been demonstrated as a promising route toward novel electronic and optoelectronic devices. Here, we report organic thin film transistors based on vertical heterojunctions of graphene and organic semiconductors. In these thin heterostructure devices, current modulation is accomplished by tuning of the injection barriers at the semiconductor/graphene interface with the application of a gate voltage. N-channel devices fabricated with a thin layer of C60 show a room temperature on/off ratio >10(4) and current density of up to 44 mAcm(-2). Because of the ultrashort channel intrinsic to the vertical structure, the device is fully operational at a driving voltage of 200 mV. A complementary p-channel device is also investigated, and a logic inverter based on two complementary transistors is demonstrated. The vertical integration of graphene with organic semiconductors via simple, scalable, and low-temperature fabrication processes opens up new opportunities to realize flexible, transparent organic electronic, and optoelectronic devices.

Basketball training influences shot selection assessment: a multi-attribute decision-making approach

Directory of Open Access Journals (Sweden)

Javier Llorca-Miralles

2013-01-01

Full Text Available A pesar del hecho de que la selección de tiro es un ingrediente crucial del rendimiento en baloncesto, el juicio y la toma de decisiones que participan en él han sido ampliamente descuidado. En el presente trabajo, analizamos las estrategias de los individuos para evaluar la adecuación de tiro (en una tarea de laboratorio de simulación en situaciones que varían en el grado de bienestar físico presión defensiva, rebote, balance defensivo y la distancia de lanzamiento. Los resultados mostraron que las cuatro dimensiones de destino tenían un impacto en los juicios de los participantes. Más importante aún, la formación influye en el grado en que una de las dimensiones no evidentes (balance defensivo es tomado en cuenta por los participantes para hacer sus juicios. Estos resultados subrayan la necesidad de desarrollar medidas de calidad de disparo selección de decisión más allá de las tasas de puntuación.

Densidad estacional y distribución vertical de los Enchytraeidae (Annelida: Oligochaeta en diferentes sistemas de producción Seasonal density and vertical distribution of Enchytraeidae (Annelida: Oligochaeta in different production systems

Directory of Open Access Journals (Sweden)

Alicia Noemí López

2005-12-01

Full Text Available En el sudeste de la provincia de Buenos Aires existe escasa información sobre la actividad de los enquitreidos en diferentes sistemas de producción. Los objetivos de este trabajo fueron determinar: a la importancia relativa de los enquitreidos dentro de la mesofauna; b su densidad estacional en relación con el grado de disturbio de los sistemas y c su distribución vertical. Este trabajo se realizó estacionalmente desde 1998 a 2001 en Balcarce, Argentina (37º 45'S, 58º 18'W, en cuatro lotes experimentales: natural (NAT, ganadero orgánico (GO, ganadero intensivo (GI y agrícola convencional (AC y en un suelo Argiudol Típico (NAT y Hapludol Tapto-Árgico (AC, GI y GO. Dentro de la comunidad mesofaunal, los enquitreidos fueron los más abundantes. GO (78 % y GI (68.5 % tuvieron un porcentaje menor que los sistemas más disturbado, AC (84.9 % y sin disturbios, NAT (93 %. El estudio comparativo de la densidad mostró interacción significativas entre sistemas y estación (p In the Southeastern of Buenos Aires Province little information exists on activity of enchytraeids under different production systems. The aims of this work were to determine: a the relative importance of enchytraeids among the components of the mesofaunal community; b the relationship between seasonal enchytraeids density (PD in different production systems, and c identify of pattern vertical distribution .This work was done seasonally from 1998 to 2001, on four experimental plots: natural (NAT, organic livestock (GO, intensive fertilization livestock (GI and conventional agriculture (AC at Balcarce, Argentina (37º 45'S, 58º 18'W, on soil Typic Argiudol (NAT and a Hapludol Tapto Árgico (AC, GI y GO. Enchytraeids were the most abundant in the mesofaunal community; GO (78% and GI (68,5% to supported a minor average those agroecosystems under intensive cultivation (84,9% and undisturbed soils NAT (93%. The comparative study showed significant interaction between site and

New movable plate for efficient millimeter wave vertical on-chip antenna

KAUST Repository

Marnat, Loic; Carreno, Armando Arpys Arevalo; Conchouso Gonzalez, David; Galicia Martinez, Miguel Angel; Foulds, Ian G.; Shamim, Atif

2013-01-01

A new movable plate concept is presented in this paper to realize mm-wave vertical on-chip antennas through MEMS based post-processing steps in a CMOS compatible process. By virtue of its vertical position, the antenna is isolated from the lossy Si substrate and hence performs with a better efficiency as compared to the horizontal position. In addition, the movable plate concept enables polarization diversity by providing both horizontal and vertical polarizations on the same chip. Through a first iteration fractal bowtie antenna design, dual band (60 and 77 GHz) operation is demonstrated in both horizontal and vertical positions without any change in dimensions or use of switches for two different mediums (Si and air). To support the movable plate concept, the transmission line and antenna are designed on a flexible polyamide, where the former has been optimized to operate in the bent position. The design is highly suitable for compact, low cost and efficient SoC solutions. © 1963-2012 IEEE.

New movable plate for efficient millimeter wave vertical on-chip antenna

KAUST Repository

Marnat, Loic

2013-04-01

A new movable plate concept is presented in this paper to realize mm-wave vertical on-chip antennas through MEMS based post-processing steps in a CMOS compatible process. By virtue of its vertical position, the antenna is isolated from the lossy Si substrate and hence performs with a better efficiency as compared to the horizontal position. In addition, the movable plate concept enables polarization diversity by providing both horizontal and vertical polarizations on the same chip. Through a first iteration fractal bowtie antenna design, dual band (60 and 77 GHz) operation is demonstrated in both horizontal and vertical positions without any change in dimensions or use of switches for two different mediums (Si and air). To support the movable plate concept, the transmission line and antenna are designed on a flexible polyamide, where the former has been optimized to operate in the bent position. The design is highly suitable for compact, low cost and efficient SoC solutions. © 1963-2012 IEEE.

Transmissão Vertical Zero: parceria entre o serviço público e o terceiro setor Transmisión Vertical Cero: sociedad entre el servicio público y el Tercer Sector Project Zero Perinatal HIV Transmission: partnership between public and private agencies

Directory of Open Access Journals (Sweden)

Janie Maria de Almeida

2009-01-01

Full Text Available OBJETIVOS: Divulgar experiência multidisciplinar de parceria entre gestores da rede pública de saúde e organizações não-governamentais voltadas à atenção à gestante HIV positivo; e caracterizar as situações de exposição ao HIV por gestantes atendidas pelo Projeto Transmissão Vertical Zero do Município de Sorocaba - SP. MÉTODOS: Estudo retrospectivo com emprego de fontes documentais, e com levantamento de dados para caracterização sócio-demográfica e situações de exposição ao risco de infecção pelo HIV de 120 gestantes atendidas pelo Projeto, entre 1998 e 2004. RESULTADOS: O compartilhamento de ações entre o público e o terceiro setor constituiu-se em eficiente alternativa de assistência à mulher soropositiva para o HIV, ainda que 56,7% das gestantes desconhecessem a sorologia do parceiro e 73,3% nunca terem usado preservativo. CONCLUSÃO: A parceria contribuiu para a redução da transmissão vertical do HIV em Sorocaba - SP.OBJETIVOS: Divulgar la experiencia multidisciplinaria de sociedad entre gestores de la red pública de salud y organizaciones no gubernamentales dirigidas a la atención de la gestante VIH positivo; y caracterizar las situaciones de exposición al VIH por gestantes atendidas por el Proyecto Transmisión Vertical Zero del Municipio de Sorocaba - SP. MÉTODOS: Se trata de un estudio retrospectivo realizado con el empleo de fuentes documentales, y con el levantamiento de datos para caracterización socio-demográfica y situaciones de exposición al riesgo de infección por el VIH de 120 gestantes atendidas por el Proyecto, entre 1998 y 2004. RESULTADOS: El compartir acciones entre el público y el tercer sector se constituye en una eficiente alternativa de asistencia a la mujer seropositiva para el VIH, aunque el 56,7% de las gestantes desconociese la serología de la pareja y el 73,3% nunca haya usado preservativo. CONCLUSIÓN: La sociedad contribuyó a la reducción de la transmisión vertical

Structure constants of the OSP(1 vertical stroke 2) WZNW model

Energy Technology Data Exchange (ETDEWEB)

Hikida, Y.; Schomerus, V.

2007-11-15

We propose exact formulas for the 2- and 3-point functions of the WZNW model on the non-compact supergroup OSP(1 vertical stroke 2). Using the path integral approach that was recently developed in arXiv:0706.1030 we show how local correlation functions in the OSP(p vertical stroke 2) WZNW models can be obtained from those of N=p supersymmetric Liouville field theory for p=1,2. We then employ known results on correlators in N=1 Liouville theory to determine the structure constants of the OSP(1 vertical stroke 2) theory. (orig.)

Efecto de la presión ambiental en la efectividad del lanzamiento al aro y la ansiedad previa a la ejecución en basquetbolistas principiantes y avanzados

Directory of Open Access Journals (Sweden)

Guadalupe Delgado Socatelli

2003-01-01

Full Text Available Con el objetivo de determinar si las condiciones de presión ambiental dadas por: el tiempo de ejecución, y la ausencia o presencia de público afectaban el rendimiento de 10 jugadores de baloncesto principiantes y 10 jugadores avanzados al ejecutar 10 tiros libres al aro lo cual permitiría conocer los cambios en la ansiedad grupal e individual de los participantes mediante la aplicación de los instrumentos POMS de McNair, Loor y Droppleman (1971 y el CSAI-2 de Martens y Vealey (1990. El análisis estadístico se efectuó mediante la aplicación de un ANOVA de medidas repetidas para buscar diferencias entre los intentos según el tipo de presión. La determinación de las diferencias entre grupos, entre las mediciones, según el nivel de presión ambiental, y la interacción de la presión de los grupos, se hizo mediante la aplicación de un ANOVA Factorial Mixto. Los resultados de la investigación permitieron corroborar la individualidad de las respuestas de la ansiedad ante distintas situaciones y la importancia de la personalización del afrontamiento para el manejo de la ansiedad competitiva

Influence of vertical coupling on the lasing operation of quantum-dash laser

KAUST Repository

Khan, Mohammed Zahed Mustafa; Ng, Tien Khee; Ooi, Boon S.

2012-01-01

The authors numerically investigated the consequence of vertical coupling among multi-stack InAs quantum dash (Qdash) laser structure on the lasing bandwidth. The developed model is based on multi-population carrier-photon rate equation

Vertically oriented TiO(x)N(y) nanopillar arrays with embedded Ag nanoparticles for visible-light photocatalysis.

Science.gov (United States)

Jiang, Weitao; Ullah, Najeeb; Divitini, Giorgio; Ducati, Caterina; Kumar, R Vasant; Ding, Yucheng; Barber, Zoe H

2012-03-27

We present a straightforward method to produce highly crystalline, vertically oriented TiO(x)N(y) nanopillars (up to 1 μm in length) with a band gap in the visible-light region. This process starts with reactive dc sputtering to produce a TiN porous film, followed by a simple oxidation process at elevated temperatures in oxygen or air. By controlling the oxidation conditions, the band gap of the prepared TiO(x)N(y) can be tuned to different wavelength within the range of visible light. Furthermore, in order to inhibit carrier recombination to enhance the photocatalytic activity, Ag nanoparticles have been embedded into the nanogaps between the TiO(x)N(y) pillars by photoinduced reduction of Ag(+) (aq) irradiated with visible light. Transmission electron microscopy reveals that the Ag nanoparticles with a diameter of about 10 nm are uniformly dispersed along the pillars. The prepared TiO(x)N(y) nanopillar matrix and Ag:TiO(x)N(y) network show strong photocatalytic activity under visible-light irradiation, evaluated via degradation of Rhodamine B. © 2012 American Chemical Society

Vertical gastric plication versus Nissen fundoplication in the treatment of gastroesophageal reflux in children with cerebral palsy

Directory of Open Access Journals (Sweden)

Antonio Paulo Durante

Full Text Available CONTEXT AND OBJECTIVE: Association between neurological lesions and gastroesophageal reflux disease (GERD in children is very common. When surgical treatment is indicated, the consensus favors the fundoplication technique recommended by Nissen, despite its high morbidity and relapse rates. Vertical gastric plication is a procedure that may have advantages over Nissen fundoplication, since it is less aggressive and more adequately meets anatomical principles. The authors proposed to compare the results from the Nissen and vertical gastric plication techniques. DESIGN AND SETTING: Randomized prospective study within the Postgraduate Surgery and Experimentation Program of Unifesp-EPM, at Hospital do Servidor Público Estadual (IAMSPE and Hospital Municipal Infantil Menino Jesus. METHODS: Fourteen consecutive children with cerebral palsy attended between November 2003 and July 2004 were randomized into two groups for surgical treatment of GERD: NF, Nissen fundoplication (n = 7; and VGP, vertical gastric plication (n = 7. These were clinically assessed by scoring for signs and symptoms, evaluation of esophageal pH measurements, duration of the operation, intra and postoperative complications, mortality and length of hospital stay. RESULTS: The mean follow-up was 5.2 months; symptoms were reduced by 42.8% (NF (p = 0.001 and 57.1% (VGP (p = 0.006. The Boix-Ochoa score was favorable for both groups: NF (p < 0.001 and VGP (p < 0.042. The overall mortality was 14.28% in both groups and was due to causes unrelated to the surgical treatment. CONCLUSION: The two operative procedures were shown to be efficient and efficacious for the treatment of GERD in neuropathic patients, over the study period.

Vertical compared with transverse incisions in abdominal surgery

DEFF Research Database (Denmark)

Grantcharov, T P; Rosenberg, J

2001-01-01

, and late complications (incisional hernia). RESULTS: Eleven randomised controlled trials and seven retrospective studies were identified. The transverse incision offers as good an access to most intra-abdominal structures as a vertical incision. The transverse incision results in significantly less......OBJECTIVE: To reach an evidence-based consensus on the relative merits of vertical and transverse laparotomy incisions. DESIGN: Review of all published randomised controlled trials that compared the postoperative complications after the two main types of abdominal incisions, vertical and transverse....... SETTING: Teaching hospital, Denmark. SUBJECTS: Patients undergoing open abdominal operations. INTERVENTIONS: For some of the variables (burst abdomen and incisional hernia) it was considered adequate to include retrospective studies. Studies were identified through Medline, Cochrane library, Embase...

Analysis of the problems of induced draft fans in a carbo-electric power station; Analisis de la problematica de ventiladores de tiro inducido de una central carboelectrica

Energy Technology Data Exchange (ETDEWEB)

Diaz Sanchez, Valentin de Jesus; Vital Flores, Francisco [LAPEM, Comision Federal de Electricidad (Mexico)

2007-11-15

The induced draft fans of the 350 MW units of a Thermo-electric power plant presented problems consisting of the failure of the capacity of gases extraction, together with the presence of cracks in the blades; this condition was observed since the stage of putting into service. Consequently, losses have been originated in the availability in two units, as well as, losses due to the manufacture of new impellers, which also originated that, in some cases, that the measures of the impellers, locally manufactured, differed from the originals, resulting in differences in the unit's efficiency. [Spanish] Los ventiladores tiro inducido de las unidades de 350 MW de una Central Termoelectrica presentaban una problematica consistente en la falla de capacidad de extraccion de gases, aunado a la presencia de fracturas en las aspas de los impulsores, esta condicion se observo desde la etapa de puesta en servicio. En consecuencia se han ocasionado perdidas de disponibilidad en dos unidades, asi como tambien, perdidas debido a la fabricacion de nuevos impulsores, lo que tambien origino que, en algunos casos, las medidas de los impulsores, fabricados localmente, diferian de los originales, dando como resultado diferencias en la eficiencia de las unidades.

Hybrid normed ideal perturbations of n-tuples of operators I

Science.gov (United States)

Voiculescu, Dan-Virgil

2018-06-01

In hybrid normed ideal perturbations of n-tuples of operators, the normed ideal is allowed to vary with the component operators. We begin extending to this setting the machinery we developed for normed ideal perturbations based on the modulus of quasicentral approximation and an adaptation of our non-commutative generalization of the Weyl-von Neumann theorem. For commuting n-tuples of hermitian operators, the modulus of quasicentral approximation remains essentially the same when Cn- is replaced by a hybrid n-tuple Cp1,…- , … , Cpn- , p1-1 + ⋯ + pn-1 = 1. The proof involves singular integrals of mixed homogeneity.

Highly aligned vertical GaN nanowires using submonolayer metal catalysts

Science.gov (United States)

Wang, George T [Albuquerque, NM; Li, Qiming [Albuquerque, NM; Creighton, J Randall [Albuquerque, NM

2010-06-29

A method for forming vertically oriented, crystallographically aligned nanowires (nanocolumns) using monolayer or submonolayer quantities of metal atoms to form uniformly sized metal islands that serve as catalysts for MOCVD growth of Group III nitride nanowires.

Aproximación experimental de un medio informático para el diagnóstico psicológico de atletas de la ESPA de Santiago de Cuba

Directory of Open Access Journals (Sweden)

Ernesto Hernandez Bridón

2007-03-01

Full Text Available El trabajo propicia la aplicación de un medio informático, presentado en soporte para el trabajo de profesionales: psicólogos y entrenadores, como una alternativa para viabilizar el proceso de evaluación de 17 Test Psicológicos cuantitativos, utilizados para la obtención diagnóstica en diferentes momentos de la Preparación Psicológica de atletas, categoría juvenil de la ESPA de Santiago de Cuba : 9 de Judo (F, 5 Baloncesto (M y 4 de Tiro con Arco, con el fin de garantizar una rápida orientación e intervención psicológica individual y grupal de los atletas. El medio cumple dos funciones: una educativa al brindar la posibilidad de adquirir y corroborar conocimientos nuevos o ya aprendidos y una investigativa.

Brooks–Corey Modeling by One-Dimensional Vertical Infiltration Method

Directory of Open Access Journals (Sweden)

Xuguang Xing

2018-05-01

Full Text Available The laboratory methods used for the soil water retention curve (SWRC construction and parameter estimation is time-consuming. A vertical infiltration method was proposed to estimate parameters α and n and to further construct the SWRC. In the present study, the relationships describing the cumulative infiltration and infiltration rate with the depth of the wetting front were established, and simplified expressions for estimating α and n parameters were proposed. The one-dimensional vertical infiltration experiments of four soils were conducted to verify if the proposed method would accurately estimate α and n. The fitted values of α and n, obtained from the RETC software, were consistent with the calculated values obtained from the infiltration method. The comparison between the measured SWRCs obtained from the centrifuge method and the calculated SWRCs that were based on the infiltration method displayed small values of root mean square error (RMSE, mean absolute percentage error (MAPE, and mean absolute error. SWMS_2D-based simulations of cumulative infiltration, based on the calculated α and n, remained consistent with the measured values due to small RMSE and MAPE values. The experiments verified the proposed one-dimensional vertical infiltration method, which has applications in field hydraulic parameter estimation.

77 FR 16928 - Drawbridge Operation Regulation; Miami River, Miami, FL

Science.gov (United States)

2012-03-23

...,'' and then click on the balloon shape in the ``Actions'' column. If you submit your comments [[Page... N.W. 12th Avenue Bridge provides a vertical clearance of 22 feet above mean high water in the closed position, and a horizontal clearance of 150 feet. The normal operating schedule for the bridge is set forth...

Vertical Lift by Series Hybrid Power, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — A major market for vertical lift aircraft is in urban operations, primarily for police and electronic news gathering (typically a Bell 206 or a Eurocopter AS350)....

The solutions of the n-dimensional Bessel diamond operator and the ...

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

Introduction. Gelfand and Shilov [2] have first introduced the elementary solution of the n-dimensional classical diamond operator. Later, Kananthai [3–5] has proved the distribution related to the n-dimensional ultra-hyperbolic equation, the solutions of n-dimensional classical diamond operator and Fourier transformation of ...

Estratificación vertical y preferencia de hospedero de las epífitas vasculares de un bosque nublado de Chiapas, México

Directory of Open Access Journals (Sweden)

Nayely Martínez-Meléndez

2008-12-01

Full Text Available En escala local, la alta diversidad de epífitas vasculares en bosques montanos neotropicales ha sido explicada por que logran estratificar verticalmente al dosel y tienen relaciones específicas con sus hospederos. En un bosque de montaña estudiamos la estratificación vertical y las preferencias de hospedero de las epífitas vasculares en un cuadrante de 0.0625 ha en donde muestreamos 41 árboles ≥10 DAP, durante 12 meses en los años 2001 y 2002. Encontramos 43 especies de epífitas en 15 géneros de árboles. Probamos preferencia de estratos verticales o de hospedero con 19 táxones epífitos. Encontramos evidencia de que las epífitas se dividen el dosel; aunque, las epífitas dispersadas por animales tendieron a ser generalistas. Entre las epífitas dispersadas por el viento reconocimos una clara estratificación vertical, concentrando especies en la parte baja de los árboles. En promedio las especies de epífitas prefirieron 3.5 especies de hospederos, sugiriendo una baja preferencia. Dos especies de árboles resultaron ser malos hospederos, Ardisia y Quercus. Nuestros resultados muestran que las epífitas parten el dosel horizontalmente, se estratifican verticalmente y sugieren que la identidad de los hospederos es importante por que puede determinar la abundancia de sitios colonizables para muchas epífitas.Vertical stratification and host preference by vascular epiphytes in a Chiapas, Mexico, cloud forest. The high diversity of vascular epiphytes in neotropical montane forest has been explained as the result of vertical stratification of the forest and specific relationships between epiphytes and their hosts trees at local scales. In a lower montane cloud forest, we studied the vertical stratification and host preferences of vascular epiphytes in a 0.0625 ha plot where 41 trees ≥ of 10 cm DBH were sampled during 12 months in 2001 and 2002. We found 43 epiphyte species growing on 15 tree genera. We tested for vertical strata and

Arno Tali õpetaja piilub aastate taha / Liina Valper

Index Scriptorium Estoniae

Valper, Liina, 1941-

2007-01-01

Matemaatikaõpetaja Salme Tiro õpetas õpilasi-näitlejaid "Kevade" filmimise ajal ja järel, et nad filmimise pärast koolis raskustesse ei satuks. Pikemalt meenutab ta Arno Tali osatäitjat Arno Liiverit

Van der Waals epitaxial growth and optoelectronics of large-scale WSe2/SnS2 vertical bilayer p-n junctions.

Science.gov (United States)

Yang, Tiefeng; Zheng, Biyuan; Wang, Zhen; Xu, Tao; Pan, Chen; Zou, Juan; Zhang, Xuehong; Qi, Zhaoyang; Liu, Hongjun; Feng, Yexin; Hu, Weida; Miao, Feng; Sun, Litao; Duan, Xiangfeng; Pan, Anlian

2017-12-04

High-quality two-dimensional atomic layered p-n heterostructures are essential for high-performance integrated optoelectronics. The studies to date have been largely limited to exfoliated and restacked flakes, and the controlled growth of such heterostructures remains a significant challenge. Here we report the direct van der Waals epitaxial growth of large-scale WSe 2 /SnS 2 vertical bilayer p-n junctions on SiO 2 /Si substrates, with the lateral sizes reaching up to millimeter scale. Multi-electrode field-effect transistors have been integrated on a single heterostructure bilayer. Electrical transport measurements indicate that the field-effect transistors of the junction show an ultra-low off-state leakage current of 10 -14 A and a highest on-off ratio of up to 10 7 . Optoelectronic characterizations show prominent photoresponse, with a fast response time of 500 μs, faster than all the directly grown vertical 2D heterostructures. The direct growth of high-quality van der Waals junctions marks an important step toward high-performance integrated optoelectronic devices and systems.

GaN-based vertical-cavity surface-emitting lasers with tunnel junction contacts grown by metal-organic chemical vapor deposition

Science.gov (United States)

Lee, SeungGeun; Forman, Charles A.; Lee, Changmin; Kearns, Jared; Young, Erin C.; Leonard, John T.; Cohen, Daniel A.; Speck, James S.; Nakamura, Shuji; DenBaars, Steven P.

2018-06-01

We report the first demonstration of III–nitride vertical-cavity surface-emitting lasers (VCSELs) with tunnel junction (TJ) intracavity contacts grown completely by metal–organic chemical vapor deposition (MOCVD). For the TJs, n++-GaN was grown on in-situ activated p++-GaN after buffered HF surface treatment. The electrical properties and epitaxial morphologies of the TJs were first investigated on TJ LED test samples. A VCSEL with a TJ intracavity contact showed a lasing wavelength of 408 nm, a threshold current of ∼15 mA (10 kA/cm2), a threshold voltage of 7.8 V, a maximum output power of 319 µW, and a differential efficiency of 0.28%.

A new design of automatic vertical drilling tool

Directory of Open Access Journals (Sweden)

Yanfeng Ma

2015-09-01

Full Text Available In order to effectively improve penetration rates and enhance wellbore quality for vertical wells, a new Automatic Vertical Drilling Tool (AVDT based on Eccentric Braced Structure (EBS is designed. Applying operating principle of rotary steering drilling, AVDT adds offset gravity block automatic induction inclination mechanism. When hole straightening happens, tools take essentric moment to be produced by gravity of offset gravity lock to control the bearing of guide force, so that well straightening is achieved. The normal tool's size of the AVDT is designed as 215.9 mm，other major components' sizes are worked out by the result of theoretical analysis, including the offset angle of EBS. This paper aims to introduce the structure, operating principle, theoretical analysis and describe the key components' parameters setting of the AVDT.

Vertical structure use by the Stout Iguana (Cyclura pinguis) on Guana Island, BVI

Science.gov (United States)

Cheek, Christopher A.; Hlavaty, Shay; Perkins, Rebecca N.; Peyton, Mark A.; Ryan, Caitlin N.; Zavaleta, Jennifer C.; Boal, Clint W.; Perry, Gad

2013-01-01

The Stout Iguana (Cyclura pinguis) is a critically endangered species endemic to the Puerto Rico Bank and currently restricted to the British Virgin Islands (BVI). Our study on Guana Island, BVI, focused on vertical structure use. Based on previous incidental observations, we hypothesized that Stout Iguanas use vertical structures and that adults and juveniles use such structures differently. In October 2011, we documented movement and vertical structure use by adult (n = 4) and juvenile (n = 11) iguanas with tracking bobbins. We recorded structure types used, heights attained on structures, distances between structures, and structure sizes. We found that Stout Iguanas used vertical structure more than previously documented. Trees comprised a significantly greater (P Iguanas. Habitat management that provides vertical structure may be advantageous for the conservation of this species.

Refining geoid and vertical gradient of gravity anomaly

Directory of Open Access Journals (Sweden)

Zhang Chijun

2011-11-01

Full Text Available We have derived and tested several relations between geoid (N and quasi-geoid (ζ with model validation. The elevation correction consists of the first-term (Bouguer anomaly and second-term (vertical gradient of gravity anomaly. The vertical gradient was obtained from direct measurement and terrain calculation. The test results demonstrated that the precision of geoid can reach centimeter-level in mountains less than 5000 meters high.

Análisis de la ubicación vertical y profundización del pin frontal en cirugía ortognática Analysis of the vertical position and depth of the external pin in orthognatic surgery

Directory of Open Access Journals (Sweden)

Pedro Solé

2012-06-01

Full Text Available Introducción: Al reposicionar verticalmente el maxilar es necesario contar con un aditamento externo llamado pin, que permite realizar las mediciones durante la cirugía, y así movilizar el maxilar según lo planificado. Los sitios más utilizados para introducir el pin son el nasion y glabela, pero ¿cuál de estos es el ideal?, siendo ideal aquella zona que de mayor retención, estabilidad y menor posibilidad de complicaciones. Objetivo: Analizar desde un punto de vista anatómico el mejor sitio para la introducción del pin, y proponer una ubicación única universal tanto en sentido vertical como sagital, utilizable para todo tipo de paciente. Material y método: Se realizó un estudio exploratorio, seleccionando al azar 99 pacientes de edad entre los 21 a los 27 años, todos estudiantes de odontología de la Universidad de los Andes Santiago de Chile, a los cuales se les efectuó una radiografía de perfil, midiendo el grosor de tejido óseo y blando a nivel del nasion y glabela. Se dividió a los pacientes por sexo y biotipo con el fin de evaluar similitudes en las mediciones de grosores. Resultados: Se encontró gran diferencia de los grosores en los distintos grupos tanto en nasion como en glabela. Se determinó un mayor grosor de tejido óseo y blando a nivel de nasion, resultando un grosor mínimo total de 13,83mm en nasion y 6,37mm en glabela. Conclusión: Debido al gran margen de grosores es muy difícil determinar un valor único estándar en la introducción del pin, considerando como sitio de elección el nasion.Introduction: To vertically reposition the maxilla it is necessary to have an attachment called the external pin, which allows for measurements to be taken during surgery. The sites most often used to insert the pin are the nasion and glabella, but the question remains as to which of these two sites is the optimum as regards increased retention, stability, and less chance of intraoperative and postoperative complications

NOAA Climate Data Record (CDR) of Visible and Near Infrared Reflectance from AVHRR, Version 1.0

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The AVHRR visible gains and offsets convert GAC pixel level counts to radiances and are provided for each visible band encompassing TIROS-N, NOAA-6 through NOAA-19...

Transmisión vertical del VIH: Comprendiendo el sentimiento de los padres por la técnica proyectiva HIV Vertical Transmission: Understanding the parents' feelings through the projective technique

Directory of Open Access Journals (Sweden)

Janie Maria de Almeida

2009-06-01

Full Text Available Estudio cualitativo realizado con padres de lactantes expuestos al VIH, cuya madre está inscrita en el Programa Transmisión Vertical Cero, Sorocaba, SP. El objetivo es identificar sentimientos relacionados con la fe religiosa de estos padres ante la indefinición del diagnóstico para el VIH del lactante. La investigación fue aprobada por un Comité de Ética en Investigación y siguió la Resolución 196/96. Para la recolección de datos se empleó la técnica proyectiva con montaje elaborada a partir de la pregunta "¿como ha sido para ustedes vivir el día-a-día esperando el resultado final de la prueba antiVIH del bebé?". La narrativa sobre su significado fue el paso siguiente. Se verificó que esta técnica fue eficiente para desencadenar el pensamiento de los participantes, para conducir y sustentar sus relatos. De los datos emergieron cinco temas, de los cuales destacamos religiosidad y espiritualidad que muestran que tienen fe y esperanza en un futuro saludable para el hijo expuesto al VIH.Qualitative study carried out with parents of newborn babies exposed to HIV whose mothers are registered at the Zero Vertical Transmission Program in Sorocaba, SP. The study aimed to identify feelings concerning the parents' religious faith while the baby seropositivity diagnosis for HIV is not defined yet. The research was approved by the Ethical Committee in Research according to Resolution 196/96. The projective technique was used for data collection in order to get answers for the following question: "how do you feel living your daily routine while you wait for your baby anti HIV test final result?" Speaking about its meaning was the next step. This technique has proved to be efficient in triggering the participants' thoughts and also in leading and supporting their reports. Five topics came up from the data collection; we highlighted two topics, religiosity and spirituality, which showed that having faith means being hopeful about the exposed

Vertical retorts for distilling, carbonizing, roasting, etc

Energy Technology Data Exchange (ETDEWEB)

Walker, H R.L.; Bates, W R

1917-11-17

In a continuously operated vertical retort for destructive distillation or roasting the combination of an annular internally and externally heated construction with an annular plunger adapted to compress and assist the travel of the charge and to aid in discharging material substantially is described.

Influence of laser lift-off on optical and structural properties of InGaN/GaN vertical blue light emitting diodes

Directory of Open Access Journals (Sweden)

M. H. Doan

2012-06-01

Full Text Available The influences of the laser lift-off (LLO process on the InGaN/GaN blue light emitting diode (LED structures, grown on sapphire substrates by low-pressure metalorganic chemical vapor deposition, have been comprehensively investigated. The vertical LED structures on Cu carriers are fabricated using electroplating, LLO, and inductively coupled plasma etching processes sequentially. A detailed study is performed on the variation of defect concentration and optical properties, before and after the LLO process, employing high-resolution transmission electron microscopy (HRTEM, scanning electron microscopy (SEM observations, cathodoluminescence (CL, photoluminescence (PL, and high-resolution X-ray diffraction (HRXRD measurements. The SEM observations on the distribution of dislocations after the LLO show well that even the GaN layer near to the multiple quantum wells (MQWs is damaged. The CL measurements reveal that the peak energy of the InGaN/GaN MQW emission exhibits a blue-shift after the LLO process in addition to a reduced intensity. These behaviors are attributed to a diffusion of indium through the defects created by the LLO and creation of non-radiative recombination centers. The observed phenomena thus suggest that the MQWs, the active region of the InGaN/GaN light emitting diodes, may be damaged by the LLO process when thickness of the GaN layer below the MQW is made to be 5 μm, a conventional thickness. The CL images on the boundary between the KrF irradiated and non-irradiated regions suggest that the propagation of the KrF laser beam and an accompanied recombination enhanced defect reaction, rather than the propagation of a thermal shock wave, are the main origin of the damage effects of the LLO process on the InGaN/GaN MQWs and the n-GaN layer as well.

The analysis of the differences between the results of the thermal response test and the data from the operation of the brine-to-water heat pump's vertical exchanger

Science.gov (United States)

Fidorów-Kaprawy, Natalia; Stefanowicz, Ewelina; Mazurek, Wojciech; Szulgowska-Zgrzywa, Małgorzata; Bryszewska-Mazurek, Anna

2017-11-01

The article discusses the principles and the problems of obtaining an accurate data input for the design of brine-to-water heat pump's vertical exchangers. Currently, the most accurate method is the thermal response test (TRT). Unfortunately, the test procedure has its limitations and the quality of the results depends on many factors that cannot be fully controlled during the test. As an illustration of the problems, the results of the TRT were presented. The test was executed on the vertical boreholes (one actively regenerated and one not actively regenerated during the summer) which are parts of the operating heat pump system. The test results were compared to the data from the device's operation, in particular with the measurements of the undisturbed ground temperature profiles and the actual unit energy gains from the boreholes. The level of difference between the results of the test and the data from the operation of the boreholes under the real load and the threats concerning the boreholes overload were shown. Additionally the performance differences between the actively regenerated and not actively regenerated boreholes have been emphasised.

Estructura de la comunidad y distribución vertical de la macrofauna de fondos blandos en isla Gorgona, Pacífico Colombiano

Directory of Open Access Journals (Sweden)

Bellineth Valencia

2014-02-01

Full Text Available Resumen Se evaluó la variación temporal, espacial y vertical de la estructura comunitaria de la macrofauna de fondos blandos submareales en isla Gorgona, Pacífico colombiano. Las muestras fueron colectadas en marzo y junio de 2011 mediante descorazonadores a 10m de profundidad en cinco puntos alrededor de la isla. Se registraron un total de 73 especies; poliquetos (55% y crustáceos (30% fueron los grupos dominantes en número de individuos. La estructura comunitaria evaluada mediante análisis de clasificación y ordenación, no varió temporalmente, pero si presentó diferencias entre puntos de muestreo, al parecer relacionada con la estructura del sedimento. Las mayores abundancias de la macrofauna se registraron en puntos con dominancia de partículas finas (Farallones, pero en otro punto con sustrato similar (Planchón, la abundancia fue baja, al parecer por la bioperturbación ejercida por el pez Heteroconger sp. La presencia de Heteroconger sp. en el Planchón posiblemente afectó la distribución vertical de la macrofauna, ya que en este último punto la abundancia relativa fue homogénea entre las capas analizadas (1-2-3-4-5-10cm. En los otros cuatro sitios, la abundancia de la macrofauna estuvo limitada principalmente a los primeros dos centímetros del sedimento. En Playa Blanca y Remanso el sustrato fue principalmente gravoso, registrándose en el último punto la menor riqueza, diversidad y abundancia.

Evaluation of vertical profiles to design continuous descent approach procedure

Science.gov (United States)

Pradeep, Priyank

The current research focuses on predictability, variability and operational feasibility aspect of Continuous Descent Approach (CDA), which is among the key concepts of the Next Generation Air Transportation System (NextGen). The idle-thrust CDA is a fuel economical, noise and emission abatement procedure, but requires increased separation to accommodate for variability and uncertainties in vertical and speed profiles of arriving aircraft. Although a considerable amount of researches have been devoted to the estimation of potential benefits of the CDA, only few have attempted to explain the predictability, variability and operational feasibility aspect of CDA. The analytical equations derived using flight dynamics and Base of Aircraft and Data (BADA) Total Energy Model (TEM) in this research gives insight into dependency of vertical profile of CDA on various factors like wind speed and gradient, weight, aircraft type and configuration, thrust settings, atmospheric factors (deviation from ISA (DISA), pressure and density of the air) and descent speed profile. Application of the derived equations to idle-thrust CDA gives an insight into sensitivity of its vertical profile to multiple factors. This suggests fixed geometric flight path angle (FPA) CDA has higher degree of predictability and lesser variability at the cost of non-idle and low thrust engine settings. However, with optimized design this impact can be overall minimized. The CDA simulations were performed using Future ATM Concept Evaluation Tool (FACET) based on radar-track and aircraft type data (BADA) of the real air-traffic to some of the busiest airports in the USA (ATL, SFO and New York Metroplex (JFK, EWR and LGA)). The statistical analysis of the vertical profiles of CDA shows 1) mean geometric FPAs derived from various simulated vertical profiles are consistently shallower than 3° glideslope angle and 2) high level of variability in vertical profiles of idle-thrust CDA even in absence of

Transmissão vertical do HIV: expectativas e ações da gestante soropositiva Transmisión vertical del VHI: expectativas y acciones de la gestante seropositiva HIV perinatal transmission: expectations and actions of hiv-positive pregnant women

Directory of Open Access Journals (Sweden)

Edilene Lins de Moura

2006-06-01

Full Text Available Este estudo descritivo, com abordagem qualitativa, foi motivado pelo elevado número de casos de transmissão vertical do HIV. Teve como objetivo identificar as expectativas e ações da gestante HIV positivo quanto à gravidez e ao concepto. A amostra constituiu-se de 14 gestantes infectadas, assintomáticas, que conheciam sua soropositividade antes da gravidez e que estavam no 3º trimestre de gestação. Utilizou-se entrevista para a coleta de dados que ocorreu em 2001 e 2002. Empregou-se o Método do Discurso do Sujeito Coletivo para analisar os dados. Verificou-se que, quanto à maternidade, as gestantes tinham expectativas semelhantes, adaptaram-se à gravidez, e acreditavam na soronegatividade do bebê e na efetividade do tratamento. Concluiu-se pela necessidade de implementação de orientação para a saúde direcionada à mulher com enfoque na transmissão vertical do HIV/aids.Este estudio descriptivo, con aproximación cualitativa, fue motivado por el gran número de niños con transmisión vertical del VHI. Tuvo como objetivo identificar las expectativas y acciones de la gestante VHI positivo en cuanto al embarazo y al concepto. La muestra se constituyó de 14 gestantes infectadas, asintomáticas, que conocían su seropositividad antes del embarazo y que estaban en el 3.er trimestre de gestación. Para la recolección de los datos, realizada en el período de 2001 y 2002, se utilizó la entrevista. El Método de Discurso de Sujeto Colectivo fue empleado para analizar los datos. Se verificó que, en cuanto a la maternidad, las gestantes tenían expectativas semejantes. Se adaptaron a la gestación, confiaban en que el bebé seria suero negativo y en la efectividad del tratamiento realizado. Las conclusiones orientan hacia la necesidad de implementación de orientación sobre la salud de la mujer con acercamiento en la transmisión vertical del VHI/SIDA.This descriptive study with a qualitative approach was motivated by the high number

Vertical field systems in TPE-1RM15 reversed dield pinch experiment

International Nuclear Information System (INIS)

Shimada, T.; Hirano, Y.; Yagi, Y.; Ogawa, K.; Yamane, M.; Yamaguchi, S.; Oyabu, I.; Murakami, S.

1989-01-01

Design of equilibrium control system in TPE-1RM15 is described in detail, where equilibrium is maintained bij the combinatuion of the error field at shell cuts by the external vertical field with pre-programmed wave form is essential to set up and maintain RPF discharge. Control of the equilibrium position in the vacuum vessel by using DC vertical field inside the shell at the plasma break down phase, which makes it possible to operate DC vertical field in a wide range. Tooidal asymmetry of the feeders of the pulsed vertical field coil located there. This asymmetry is compensated bij the local vertical field of saddle coil wound around the shell cuts. (author). 2 refs.;4 figs

Vertical versus Lateral Two-Dimensional Heterostructures: On the Topic of Atomically Abrupt p/n-Junctions.

Science.gov (United States)

Zhou, Ruiping; Ostwal, Vaibhav; Appenzeller, Joerg

2017-08-09

The key appeal of two-dimensional (2D) materials such as graphene, transition metal dichalcogenides (TMDs), or phosphorene for electronic applications certainly lies in their atomically thin nature that offers opportunities for devices beyond conventional transistors. It is also this property that makes them naturally suited for a type of integration that is not possible with any three-dimensional (3D) material, that is, forming heterostructures by stacking dissimilar 2D materials together. Recently, a number of research groups have reported on the formation of atomically sharp p/n-junctions in various 2D heterostructures that show strong diode-type rectification. In this article, we will show that truly vertical heterostructures do exhibit much smaller rectification ratios and that the reported results on atomically sharp p/n-junctions can be readily understood within the framework of the gate and drain voltage response of Schottky barriers that are involved in the lateral transport.

5G IoT Industry Verticals and Network Requirements

OpenAIRE

Condoluci, Massimo; Lema Rosas, Maria Angel; Mahmoodi, Toktam; Dohler, Michael

2017-01-01

The effective provisioning of industry verticals over the next-to-come 5G systems opens novel business opportunities for telco operators especially when considering the integration of Internet of Things (IoT) devices as enablers of business cases based on remote sensing and control. This chapter highlights the main features of IoT verticals with particular attention on healthcare, smart cities, industry automation and entertainment business cases. The aim of this Chapter is to derive the requ...

The large N limit of N=2 super Yang-Mills, fractional instantons and infrared divergences

International Nuclear Information System (INIS)

Ferrari, Frank

2001-01-01

We investigate the large N limit of pure N=2 supersymmetric gauge theory with gauge group SU(N) by using the exact low energy effective action. Typical one-complex dimensional sections of the moduli space parametrized by a global complex mass scale v display three qualitatively different regions depending on the ratio between vertical bar v vertical bar and the dynamically generated scale Λ. At large vertical bar v vertical bar/Λ, instantons are exponentially suppressed as N→∞. When vertical bar v vertical bar ∼Λ, singularities due to massless dyons occur. They are densely distributed in rings of calculable thicknesses in the v-plane. At small vertical bar v vertical bar/Λ, instantons disintegrate into fractional instantons of charge 1/(2N). These fractional instantons give non-trivial contributions to all orders of 1/N, unlike a planar diagrams expansion which generates a series in 1/N 2 , implying the presence of open strings. We have explicitly calculated the fractional instantons series in two representative examples, including the 1/N and 1/N 2 corrections. Our most interesting finding is that the 1/N expansion breaks down at singularities on the moduli space due to severe infrared divergencies, a fact that has remarkable consequences

Vertically integrated nanogenerator based on ZnO nanowire arrays

Energy Technology Data Exchange (ETDEWEB)

Yu, Aifang; Li, Hongyu; Tang, Haoying; Liu, Tengjiao; Jiang, Peng [National Center for Nanoscience and Technology, No.11, Beiyitiao Zhongguancun, Beijing 100190 (China); Wang, Zhong Lin [National Center for Nanoscience and Technology, No.11, Beiyitiao Zhongguancun, Beijing 100190 (China); School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0245 (United States)

2011-04-15

We report a technique to construct a vertically integrated nanogenerator (VI-NG) based on ZnO nanowire (NW) arrays. The VI-NG consists of nine single NGs connected mixed parallel and serial by a layer-by-layer stacking. For the single layer NG, the peak output voltage and current are 0.045 V and 2.5 nA, respectively. The VI-NG produces an output power density of 2.8 nW/cm{sup 2} with a peak output voltage of 0.15 V and output current of 7.2 nA. The vertical integration of the multi-NG provides a feasible technique for effectively converting mechanical energies to electricity from environment. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

The GL(1 vertical stroke 1)-symplectic fermion correspondence

International Nuclear Information System (INIS)

Creutzig, Thomas; Roenne, Peter B.

2008-12-01

In this note we prove a correspondence between the Wess-Zumino-Novikov-Witten model of the Lie supergroup GL(1 vertical stroke 1) and a free model consisting of two scalars and a pair of symplectic fermions. This model was discussed earlier by LeClair. Vertex operators for the symplectic fermions include twist fields, and correlation functions of GL(1 vertical stroke 1) agree with the known results for the scalars and symplectic fermions. We perform a detailed study of boundary states for symplectic fermions and apply them to branes in GL(1 vertical stroke 1). This allows us to compute new amplitudes of strings stretching between branes of different types and confirming Cardy's condition. (orig.)

The GL(1 vertical stroke 1)-symplectic fermion correspondence

Energy Technology Data Exchange (ETDEWEB)

Creutzig, Thomas; Roenne, Peter B.

2008-12-15

In this note we prove a correspondence between the Wess-Zumino-Novikov-Witten model of the Lie supergroup GL(1 vertical stroke 1) and a free model consisting of two scalars and a pair of symplectic fermions. This model was discussed earlier by LeClair. Vertex operators for the symplectic fermions include twist fields, and correlation functions of GL(1 vertical stroke 1) agree with the known results for the scalars and symplectic fermions. We perform a detailed study of boundary states for symplectic fermions and apply them to branes in GL(1 vertical stroke 1). This allows us to compute new amplitudes of strings stretching between branes of different types and confirming Cardy's condition. (orig.)

Dynamic behaviour studies of a vertical axis wind turbine blade using Operational Modal Analysis (OMA) and Experimental Modal Analysis (EMA)

DEFF Research Database (Denmark)

Najafi, Nadia; Schmidt Paulsen, Uwe; Belloni, F.

2014-01-01

Dynamic behavior of a modified blade fitted onto a small 1 kW vertical-axis wind turbine is studied by two different approaches: Classical modal analysis (EMA) is carried out to validate the results of Operational Modal Analysis (OMA). In traditional modal analysis (EMA) one axis accelerometers...... it is excited by random and wind forces. The cameras are programmed in LabView to take pictures at the same time with 180 fps and store them on a high speed hard disk. The output deflection will be investigated in frequency domain by peak picking method, and then AR (Autoregressive) model is applied to describe...

Two-family compensation of linear horizontal/vertical coupling

International Nuclear Information System (INIS)

Peterson, J.

1991-10-01

Many existing circular accelerators have been able to adequately compensate their horizontal/vertical coupling by one or two families of skew-quadrupole corrector magnets. For example, the HERA proton storage ring at DESY has used just two skew quadrupoles correctors, the SPS at CERN can operate with just one skew quadrupole corrector, and the Tevatron at Fermilab with two families of skew quadrupoles. At first sight just two corrector families seem unlikely to be enough, since there are four independent horizontal/vertical coupling coefficients in the 4 x 4 transfer from one point to any other in the ring. Thus, for the general case four families of correctors would seem to be necessary. It will be shown that the adequacy of two-family correction for storage rings in a consequence of operating near the diagonal of the tune diagram

Independent variations of applied voltage and injection current for controlling the quantum-confined Stark effect in an InGaN/GaN quantum-well light-emitting diode.

Science.gov (United States)

Chen, Horng-Shyang; Liu, Zhan Hui; Shih, Pei-Ying; Su, Chia-Ying; Chen, Chih-Yen; Lin, Chun-Han; Yao, Yu-Feng; Kiang, Yean-Woei; Yang, C C

2014-04-07

A reverse-biased voltage is applied to either device in the vertical configuration of two light-emitting diodes (LEDs) grown on patterned and flat Si (110) substrates with weak and strong quantum-confined Stark effects (QCSEs), respectively, in the InGaN/GaN quantum wells for independently controlling the applied voltage across and the injection current into the p-i-n junction in the lateral configuration of LED operation. The results show that more carrier supply is needed in the LED of weaker QCSE to produce a carrier screening effect for balancing the potential tilt in increasing the forward-biased voltage, when compared with the LED of stronger QCSE. The small spectral shift range in increasing injection current in the LED of weaker QCSE is attributed not only to the weaker QCSE, but also to its smaller device resistance such that a given increment of applied voltage leads to a larger increment of injection current. From a viewpoint of practical application in LED operation, by applying a reverse-biased voltage in the vertical configuration, the applied voltage and injection current in the lateral configuration can be independently controlled by adjusting the vertical voltage for keeping the emission spectral peak fixed.

Self-organization of dislocation-free, high-density, vertically aligned GaN nanocolumns involving InGaN quantum wells on graphene/SiO2 covered with a thin AlN buffer layer

International Nuclear Information System (INIS)

Hayashi, Hiroaki; Konno, Yuta; Kishino, Katsumi

2016-01-01

We demonstrated the self-organization of high-density GaN nanocolumns on multilayer graphene (MLG)/SiO 2 covered with a thin AlN buffer layer by RF-plasma-assisted molecular beam epitaxy. MLG/SiO 2 substrates were prepared by the transfer of CVD graphene onto thermally oxidized SiO 2 /Si [100] substrates. Employing the MLG with an AlN buffer layer enabled the self-organization of high-density and vertically aligned nanocolumns. Transmission electron microscopy observation revealed that no threading dislocations, stacking faults, or twinning defects were included in the self-organized nanocolumns. The photoluminescence (PL) peak intensities of the self-organized GaN nanocolumns were 2.0–2.6 times higher than those of a GaN substrate grown by hydride vapor phase epitaxy. Moreover, no yellow luminescence or ZB-phase GaN emission was observed from the nanocolumns. An InGaN/GaN MQW and p-type GaN were integrated into GaN nanocolumns grown on MLG, displaying a single-peak PL emission at a wavelength of 533 nm. Thus, high-density nitride p–i–n nanocolumns were fabricated on SiO 2 /Si using the transferred MLG interlayer, indicating the possibility of developing visible nanocolumn LEDs on graphene/SiO 2 . (paper)

Charge exchange K-tau scattering in the small Vertical BartVertical Bar range at momemtum 30 GeV/c

International Nuclear Information System (INIS)

Binon, F.; Gouanere, M.; Davydov, V.A.; Donskov, S.V.; Duteil, P.; Dufournaud, J.; Inayakin, A.V.; Kakauridze, D.B.; Kachanov, V.A.; Kulik, A.V.; Lagnaux, J.P.; Lednev, A.A.; Maisheev, V.A.; Mel'nik, Y.M.; Mikhailov, Y.V.; Peigneux, J.P.; Prokoshkin, Y.D.; Rodnov, Y.V.; Roosen, R.; Startsev, A.V.; Stroot, J.P.; Khaustov, G.V.

1981-01-01

Differential cross sections for the reaction K - p→K-bar 0 n at momentum 30 GeV/c have been measured with high angular resolution and statistical accuracy. The experiments were performed at the 70-GeV Serpukhov accelerator using a hodoscopic hadron calorimeter which recorded K 0 /sub L/ mesons. The t-dependence of the cross section shows a marked drop at small Vertical BartVertical Bar which corresponds to a dominant contribution from spin-flip in the rho- and A 2 -exchange amplitudes in the t-channel

Oscillator construction of su(n|m) Q-operators

Energy Technology Data Exchange (ETDEWEB)

Frassek, Rouven, E-mail: rfrassek@physik.hu-berlin.de [Institut fuer Mathematik und Institut fuer Physik, Humboldt-Universitaet zu Berlin, Johann von Neumann-Haus, Rudower Chaussee 25, 12489 Berlin (Germany); Max-Planck-Institut fuer Gravitationsphysik, Albert-Einstein-Institut, Am Muehlenberg 1, 14476 Potsdam (Germany); Lukowski, Tomasz, E-mail: lukowski@mathematik.hu-berlin.de [Institut fuer Mathematik und Institut fuer Physik, Humboldt-Universitaet zu Berlin, Johann von Neumann-Haus, Rudower Chaussee 25, 12489 Berlin (Germany); Meneghelli, Carlo, E-mail: carlo@aei.mpg.de [Institut fuer Mathematik und Institut fuer Physik, Humboldt-Universitaet zu Berlin, Johann von Neumann-Haus, Rudower Chaussee 25, 12489 Berlin (Germany); Max-Planck-Institut fuer Gravitationsphysik, Albert-Einstein-Institut, Am Muehlenberg 1, 14476 Potsdam (Germany); Staudacher, Matthias, E-mail: matthias@aei.mpg.de [Institut fuer Mathematik und Institut fuer Physik, Humboldt-Universitaet zu Berlin, Johann von Neumann-Haus, Rudower Chaussee 25, 12489 Berlin (Germany); Max-Planck-Institut fuer Gravitationsphysik, Albert-Einstein-Institut, Am Muehlenberg 1, 14476 Potsdam (Germany)

2011-09-01

We generalize our recent explicit construction of the full hierarchy of Baxter Q-operators of compact spin chains with su(n) symmetry to the supersymmetric case su(n|m). The method is based on novel degenerate solutions of the graded Yang-Baxter equation, leading to an amalgam of bosonic and fermionic oscillator algebras. Our approach is fully algebraic, and leads to the exact solution of the associated compact spin chains while avoiding Bethe ansatz techniques. It furthermore elucidates the algebraic and combinatorial structures underlying the system of nested Bethe equations. Finally, our construction naturally reproduces the representation, due to Z. Tsuboi, of the hierarchy of Baxter Q-operators in terms of hypercubic Hasse diagrams.

Vertically stacked multi-heterostructures of layered materials for logic transistors and complementary inverters

Science.gov (United States)

Yu, Woo Jong; Li, Zheng; Zhou, Hailong; Chen, Yu; Wang, Yang; Huang, Yu; Duan, Xiangfeng

2014-01-01

The layered materials such as graphene have attracted considerable interest for future electronics. Here we report the vertical integration of multi-heterostructures of layered materials to enable high current density vertical field-effect transistors (VFETs). An n-channel VFET is created by sandwiching few-layer molybdenum disulfide (MoS2) as the semiconducting channel between a monolayer graphene and a metal thin film. The VFETs exhibit a room temperature on-off ratio >103, while at same time deliver a high current density up to 5,000 A/cm2, sufficient for high performance logic applications. This study offers a general strategy for the vertical integration of various layered materials to obtain both p- and n-channel transistors for complementary logic functions. A complementary inverter with larger than unit voltage gain is demonstrated by vertically stacking the layered materials of graphene, Bi2Sr2Co2O8 (p-channel), graphene, MoS2 (n-channel), and metal thin film in sequence. The ability to simultaneously achieve high on-off ratio, high current density, and logic integration in the vertically stacked multi-heterostructures can open up a new dimension for future electronics to enable three-dimensional integration. PMID:23241535

Creation and Validation of Chronojump-Boscosystem: A Free Tool to Measure Vertical Jumps. (Creación y validación de Chronojump-Boscosystem: un instrumento libre para la medición de saltos verticales.

Directory of Open Access Journals (Sweden)

José Luis López del Amo

2012-10-01

Full Text Available Measuring the height of the vertical jump is an indicator of the strength and power of the lower body. The technological tools available to measure the vertical jump are black boxes and are not open to third-party verification or adaptation. We propose the creation of a measurement system called Chronojump-Boscosystem, consisting of open hardware and free software. Methods: A microcontroller was created and validated using a square wave generator and an oscilloscope. Two types of contact platforms were developed using different materials. These platforms were validated by the minimum pressure required for activation at different points by a strain gauge, together with the on/off time of our platforms in respect of the Ergojump-Boscosystem platform by a sample of 8 subjects performing submaximal jumps with one foot on each platform. Agile methodologies were used to develop and validate the software. Results: All the tools fall under the free software / open hardware guidelines and are, in that sense, free. The microcontroller margin of error is 0.1%. The validity of the fiberglass platform is 0.95 (ICC. The management software contains nearly 113.000 lines of code and is available in 7 languages.ResumenLa medición de la altura del salto vertical es un indicador de la fuerza y potencia del tren inferior. Los instrumentos electrónicos disponibles para medir este salto son cajas negras que no permiten la verificación ni la adaptación por parte de terceros. Proponemos la creación de un sistema de medición llamado Chronojump-Boscosystem, que consiste en un hardware abierto y un software libre. Métodos: Se ha creado un microcontrolador y se ha validado usando un generador de ondas cuadradas y un osciloscopio. Se han desarrollado dos tipos de plataformas usando materiales distintos. Las plataformas se han validado determinando su sensibilidad en distintos puntos por medio de una célula de carga, y por comparación con la plataforma de contactos

A compact dilution refrigerator with vertical heat exchangers for operation to 2 mK

International Nuclear Information System (INIS)

Bunkov, Yu.M.; Guenault, A.M.; Hayward, D.J.; Jackson, D.A.; Kennedy, C.J.; Nichols, T.R.; Miller, I.E.; Pickett, G.R.; Ward, M.G.

1991-01-01

A compactly designed dilution refrigerator with closely packed, vertical heat exchangers is described. The refrigerator reaches a temperature of 2 mK and is easily constructed, since the sintered heat exchangers are straight units. Vibrating wire resonators are employed in the mixing chamber as diagnostic tools, which may act as both thermometers and phase-boundary level indicators. There is a design problem in the vertical arrangement, namely, the sumps on the concentrated phase side that can slowly fill with dilute phase and degrade the performance. The problem is solved by draining the superfluid 4 He component in any collected dilute phase through superleaks into the mixing chamber

Measurement of Cabbibo-suppressed {tau} lepton decays and the determination of vertical stroke V{sub us} vertical stroke

Energy Technology Data Exchange (ETDEWEB)

Schenk, Stefan

2008-07-07

This work presents simultaneous branching fraction measurements of the decay modes {tau}{sup -}{yields}K{sup -}n{pi}{sup 0}{nu}{sub {tau}} with n=0,1,2,3 and {tau}{sup -}{yields}{pi}{sup -}n{pi}{sup 0}{nu}{sub {tau}} with n=3,4. The analysis is based on a data sample of 427 x 10{sup 6}{tau}{sup +}{tau}{sup -} pairs recorded with the BABAR detector, which corresponds to an integrated luminosity of 464.4 fb{sup -1}. The measured values are B({tau}{sup -}{yields}K{sup -}{nu}{sub {tau}})=(6.57{+-}0.03{+-}0.11) x 10{sup -3}, B({tau}{sup -}{yields}K{sup -}{pi}{sup 0}{nu}{sub {tau}})=(4.61{+-}0.03{+-}0.11) x 10{sup -3}, B({tau}{sup -}{yields}K{sup -}{pi}{sup 0}{pi}{sup 0}{nu}{sub {tau}})=(5.05{+-}0.17{+-}0.44) x 10{sup -4}, B({tau}{sup -}{yields}K{sup -}{pi}{sup 0}{pi}{sup 0}{pi}{sup 0}{nu}{sub {tau}})=(1.31{+-}0.43{+-}0.40) x 10{sup -4}, B({tau}{sup -}{yields}{pi}{sup -}{pi}{sup 0}{pi}{sup 0}{pi}{sup 0}{nu}{sub {tau}})=(1.263{+-}0.008{+-}0.078) x 10{sup -2} and B({tau}{sup -}{yields}{pi}{sup -}{pi}{sup 0}{pi}{sup 0}{pi}{sup 0}{pi}{sup 0}{nu}{sub {tau}})=(9.6{+-}0.5{+-}1.2) x 10{sup -4}, where the uncertainties are statistical and systematic, respectively. All measurements are compatible with the current world averages whereas the uncertainties are significantly smaller by a factor of up to five. The determination of B({tau}{sup -}{yields}{pi}{sup -}{pi}{sup 0}{pi}{sup 0}{pi}{sup 0}{pi}{sup 0}{nu}{sub {tau}}) is the first measurement of this branching fraction. The measured branching fractions are combined with the current world averages. Using the new averages, an updated determination of vertical stroke V{sub us} vertical stroke from hadronic {tau} decays yields vertical stroke V{sub us} vertical stroke =0.2146{+-}0.0025, which improves previous measurements by 19%. Its uncertainty is comparable to the one of the current world average from semileptonic kaon decays. (orig.)

Measuring of vertical stroke Vub vertical stroke in the forthcoming decade

International Nuclear Information System (INIS)

Kim, C.S.

1997-01-01

I first introduce the importance of measuring V ub precisely. Then, from a theoretician's point of view, I review (a) past history, (b) present trials, and (c) possible future alternatives on measuring vertical stroke V ub vertical stroke and/or vertical stroke V ub /V cb vertical stroke. As of my main topic, I introduce a model-independent method, which predicts Γ(B→X u lν)/Γ(B→X c lν)≡(γ u /γ c ) x vertical stroke V ub /V cb vertical stroke 2 ≅(1.83±0.28) x vertical stroke V ub /V cb vertical stroke 2 and vertical stroke V ub /V cb vertical stroke ≡(γ c /γ u ) 1/2 x [B(B→X u lν)/B(B→ X c lν]) 1/2 ≅(0.74±0.06) x [B(B→X u lν/)B(B→X c lν)] 1/2 , based on the heavy quark effective theory I also explore the possible experimental options to separate B→X u lν from the dominant B→X c lν: the measurement of inclusive hadronic invariant mass distributions, and the 'D-π' (and 'K-π') separation conditions I also clarify the relevant experimental backgrounds. (orig.)

Vertical and horizontal control dilemmas in public hospitals.

Science.gov (United States)

Pettersen, Inger Johanne; Solstad, Elsa

2015-01-01

The hospital sector in Norway has been continuously reorganized since 2002 and the reforms have created organizations that are functionally/vertically controlled, whereas the production lines are coordinated on a process or a lateral basis. The purpose of this paper is to focus on both the perceived functional vertical control and horizontal controls within and between the local hospitals and the regional administrative levels. A national survey study, complemented with interviews of some key informants and document studies. The study shows that the functional and vertical lines of management control are perceived to be operating according to the traditional views of management control. The study indicates that the horizontal tasks are not very well implemented, and we did not find interactive and lateral uses of management control systems for managerial purposes. New control problems arise when services are to be coordinated between autonomous units. The paper focuses on the control problems found within the horizontal, flat relationship between production units in hospitals; new organizational structures have emerged where lateral relations are important, but traditional control practices follow functional, vertical lines.

Ordering non-bipartite unicyclic graphs with pendant vertices by the least Q-eigenvalue

Directory of Open Access Journals (Sweden)

Shu-Guang Guo

2016-05-01

Full Text Available Abstract A unicyclic graph is a connected graph whose number of edges is equal to the number of vertices. Fan et al. (Discrete Math. 313:903-909, 2013 and Liu et al. (Electron. J. Linear Algebra 26:333-344, 2013 determined, independently, the unique unicyclic graph whose least Q-eigenvalue attains the minimum among all non-bipartite unicyclic graphs of order n with k pendant vertices. In this paper, we extend their results and determine the first three non-bipartite unicyclic graphs of order n with k pendant vertices ordering by least Q-eigenvalue.

Extension of the TCV Operating Space Towards Higher Elongation and Higher Normalized Current

International Nuclear Information System (INIS)

Hofmann, F.; Coda, S.; Lavanchy, P.; Llobet, X.; Marmillod, Ph.; Martin, Y.; Martynov, A.; Mlynar, J.; Moret, J.-M.; Pochelon, A.; Sauter, O.

2002-01-01

Recently, an experimental campaign has been launched on TCV with the aim of exploring and extending the limits of the operating space. The vertical position control system has been optimized, with the help of extensive model calculations, in order to allow operation at the lowest possible stability margin. In addition, the growth rate of the axisymmetric instability has been minimized by choosing optimum values for the plasma triangularity and squareness and by operating close to the current limit imposed by the n= 1 external kink mode. These measures have allowed us to reach record values of elongation, κ=2.8, and normalized current, I N =3.6, in a tokamak with standard aspect ratio, R/a=3.5. (author)

Integrated shell approach to vertical position control on PBX-M

International Nuclear Information System (INIS)

Hatcher, R.E.; Okabayashi, M.

1995-03-01

The PBX-M device produces highly shaped discharges that, because of the negative external magnetic field decay index required, are vertically unstable. Vertical positional stability in PBX-M has been achieved by directly controlling the n = 0 component of the eddy current in the passive shell instead of the commonly used function of magnetic flux signals. Because the active coil is controlled via currents in the passive shell we call this an ''integrated shell'' approach to vertical position control. We present results of these experiments and make comparisons between the two methods of control

Contribution to the study of the vertical molten zone process (1963)

International Nuclear Information System (INIS)

Lenzin, M.

1963-01-01

Construction and use of several molten zone apparatuses operating either vertically or horizontally. Efficient purification of uranyl nitrate hexahydrate but less successful in the case of other hydrated double salts and of zirconyl chloride in the hydrochloric gel form. Demonstration and study of the dissymmetry in the direction of the transport of the impurity during, the purification by a vertical molten zone process. (author) [fr

A New Fast Vertical Method for Mining Frequent Patterns

Directory of Open Access Journals (Sweden)

Zhihong Deng

2010-12-01

Full Text Available Vertical mining methods are very effective for mining frequent patterns and usually outperform horizontal mining methods. However, the vertical methods become ineffective since the intersection time starts to be costly when the cardinality of tidset (tid-list or diffset is very large or there are a very large number of transactions. In this paper, we propose a novel vertical algorithm called PPV for fast frequent pattern discovery. PPV works based on a data structure called Node-lists, which is obtained from a coding prefix-tree called PPC-tree. The efficiency of PPV is achieved with three techniques. First, the Node-list is much more compact compared with previous proposed vertical structure (such as tid-lists or diffsets since transactions with common prefixes share the same nodes of the PPC-tree. Second, the counting of support is transformed into the intersection of Node-lists and the complexity of intersecting two Node-lists can be reduced to O(m+n by an efficient strategy, where m and n are the cardinalities of the two Node-lists respectively. Third, the ancestor-descendant relationship of two nodes, which is the basic step of intersecting Node-lists, can be very efficiently verified by Pre-Post codes of nodes. We experimentally compare our algorithm with FP-growth, and two prominent vertical algorithms (Eclat and dEclat on a number of databases. The experimental results show that PPV is an efficient algorithm that outperforms FP-growth, Eclat, and dEclat.

Discriminant analysis of maintaining a vertical position in the water

Directory of Open Access Journals (Sweden)

Bratuša Zoran

2015-01-01

Full Text Available Water polo is the only sports game that takes place in the water. During the outplay, a vertical body position with the two basic mechanisms of the leg work - a breaststroke leg kick and an eggbeater leg kick, prevails. Starting from the significance of a vertical position during the game play, the methods of assessing physical preparedness of the athletes of all the categories also include the evaluation of maintaining a vertical position and consequently the load of the leg muscles. The measurements are performed during the maintenance of a vertical position (swimming in place through one of the specified mechanisms of leg work, i.e. a vertical position technique. The aim of this paper was to determine the application of different mechanisms of the leg kicks in maintaining a vertical position with young water polo players in relation to their position. The study included 29 selected junior water polo players (age_15.8 ± 0.8 years; BH_185.2 ± 5.3cm and BW_81.7 ± 7.7kg. The measurements were performed during the tests of swimming in place at the maximum intensity lasting 10 seconds, by the breaststroke and eggbeater leg kicks. The isometric tensiometry tests were used for the measurements. The results were analysed by the application of descriptive statistics, and the kinetic selection characteristic was defined by the application of discriminant analysis. Higher average values were achieved with the breaststroke leg kick technique Fmax, ImpF and RFD (avgFmaxLEGGBK =157.46±19.93N; avgImpF_LEGGBK =45.43±10.64Ns; avgRFD_LEGGBK=337.85±80.73N/s; avgFmaxLBKICK=227.18±49.17N; avgImpF_LBKICK=55.99±14.59Ns; avgRFD_LBKICK=545.47±159.15N/s. After discriminant analysis, the results have shown that the eggbeater leg kick is a selection technique, whereas the force - Fmax is a kinetic selection variable. Based on the obtained results and the analyses performed it may be concluded that a training factor dominant for maintaining a vertical position by

47 CFR 76.504 - Limits on carriage of vertically integrated programming.

Science.gov (United States)

2010-10-01

... programming. 76.504 Section 76.504 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST... Limits on carriage of vertically integrated programming. (a) Except as otherwise provided in this section... national video programming services owned by the cable operator or in which the cable operator has an...

Characterization of aerodynamic performance of vertical axis wind turbines : impact of operational parameters

NARCIS (Netherlands)

Rezaeiha, Abdolrahim; Montazeri, Hamid; Blocken, Bert

2018-01-01

Vertical axis wind turbines (VAWTs) have received growing interest for off-shore application and in the urban environments mainly due to their omni-directional capability, scalability, robustness, low noise and costs. However, their aerodynamic performance is still not comparable with their

Deep-water subsea lifting operations

Energy Technology Data Exchange (ETDEWEB)

Nestegaard, Arne; Boee, Tormod

2010-07-01

Significant costs are related to marine operations in the installation phase of deep water subsea field developments. In order to establish safe operational criteria and procedures for the installation, detailed planning is necessary, including numerical modelling and analysis of the environmental conditions and hydrodynamic loads on the installed object as well as the installation equipment. This paper presents recommendations for modelling and analysis of deep water subsea lifting operations developed for the new DNV RP-H103 [1]. During installation of subsea structures, the highest dynamic forces are most often encountered in the splash zone. Recommendations for estimation of maximum forces will be presented. For small structures and tools, installation through the moon pool of a small installation vessel is often preferred. Calculation methods for loading on structures installed through a moon pool will be presented. During intervention or installation in deep water a significant amplification of amplitude and forces can be experienced when the frequency range of vertical crane tip motion coincides with the natural vertical oscillation of the lift wire and load. Vertical resonance may reduce the operability of the operation. Simplified calculation methods for such operations are presented. (Author)

Cryogenic infrastructure for Fermilab's ILC vertical cavity test facility

International Nuclear Information System (INIS)

Carcagno, R.; Ginsburg, C.; Huang, Y.; Norris, B.; Ozelis, J.; Peterson, T.; Poloubotko, V.; Rabehl, R.; Sylvester, C.; Wong, M.; Fermilab

2006-01-01

Fermilab is building a Vertical Cavity Test Facility (VCTF) to provide for R and D and pre-production testing of bare 9-cell, 1.3-GHz superconducting RF (SRF) cavities for the International Linear Collider (ILC) program. This facility is located in the existing Industrial Building 1 (IB1) where the Magnet Test Facility (MTF) also resides. Helium and nitrogen cryogenics are shared between the VCTF and MTF including the existing 1500-W at 4.5-K helium refrigerator with vacuum pumping for super-fluid operation (125-W capacity at 2-K). The VCTF is being constructed in multiple phases. The first phase is scheduled for completion in mid 2007, and includes modifications to the IB1 cryogenic infrastructure to allow helium cooling to be directed to either the VCTF or MTF as scheduling demands require. At this stage, the VCTF consists of one Vertical Test Stand (VTS) cryostat for the testing of one cavity in a 2-K helium bath. Planning is underway to provide a total of three Vertical Test Stands at VCTF, each capable of accommodating two cavities. Cryogenic infrastructure improvements necessary to support these additional VCTF test stands include a dedicated ambient temperature vacuum pump, a new helium purification skid, and the addition of helium gas storage. This paper describes the system design and initial cryogenic operation results for the first VCTF phase, and outlines future cryogenic infrastructure upgrade plans for expanding to three Vertical Test Stands

CRYOGENIC INFRASTRUCTURE FOR FERMILAB'S ILC VERTICAL CAVITY TEST FACILITY

International Nuclear Information System (INIS)

Carcagno, R.; Ginsburg, C.; Huang, Y.; Norris, B.; Ozelis, J.; Peterson, T.; Poloubotko, V.; Rabehl, R.; Sylvester, C.; Wong, M.

2008-01-01

Fermilab is building a Vertical Cavity Test Facility (VCTF) to provide for R and D and pre-production testing of bare 9-cell, 1.3-GHz superconducting RF (SRF) cavities for the International Linear Collider (ILC) program. This facility is located in the existing Industrial Building 1 (IB1) where the Magnet Test Facility (MTF) also resides. Helium and nitrogen cryogenics are shared between the VCTF and MTF including the existing 1500-W at 4.5-K helium refrigerator with vacuum pumping for super-fluid operation (125-W capacity at 2-K). The VCTF is being constructed in multiple phases. The first phase is scheduled for completion in mid 2007, and includes modifications to the IB1 cryogenic infrastructure to allow helium cooling to be directed to either the VCTF or MTF as scheduling demands require. At this stage, the VCTF consists of one Vertical Test Stand (VTS) cryostat for the testing of one cavity in a 2-K helium bath. Planning is underway to provide a total of three Vertical Test Stands at VCTF, each capable of accommodating two cavities. Cryogenic infrastructure improvements necessary to support these additional VCTF test stands include a dedicated ambient temperature vacuum pump, a new helium purification skid, and the addition of helium gas storage. This paper describes the system design and initial cryogenic operation results for the first VCTF phase, and outlines future cryogenic infrastructure upgrade plans for expanding to three Vertical Test Stands

A new vertical axis wind turbine design for urban areas

Science.gov (United States)

Frunzulica, Florin; Cismilianu, Alexandru; Boros, Alexandru; Dumitrache, Alexandru; Suatean, Bogdan

2016-06-01

In this paper we aim at developing the model of a Vertical Axis Wind Turbine (VAWT) with the short-term goal of physically realising this turbine to operate at a maximmum power of 5 kW. The turbine is designed for household users in the urban or rural areas and remote or isolated residential areas (hardly accsessible). The proposed model has a biplane configuration on each arm of the VAWT (3 × 2 = 6 blades), allowing for increased performance of the turbine at TSR between 2 and 2.5 (urban area operation) compared to the classic vertical axis turbines. Results that validate the proposed configuration as well as passive control methods to increase the performance of the classic VAWTs are presented.

Vertical integration in the nuclear fuel cycle

International Nuclear Information System (INIS)

Mommsen, J.T.

1977-01-01

Vertical integration in the nuclear fuel cycle and its contribution to market power of integrated fuel suppliers were studied. The industry subdivision analyzed is the uranium raw materials sector. The hypotheses demonstrated are that (1) this sector of the industry is trending toward vertical integration between production of uranium raw materials and the manufacture of nuclear fuel elements, and (2) this vertical integration confers upon integrated firms a significant market advantage over non-integrated fuel manufacturers. Under microeconomic concepts the rationale for vertical integration is the pursuit of efficiency, and it is beneficial because it increases physical output and decreases price. The Market Advantage Model developed is an arithmetical statement of the relative market power (in terms of price) between non-integrated nuclear fuel manufacturers and integrated raw material/fuel suppliers, based on the concept of the ''squeeze.'' In operation, the model compares net profit and return on sales of nuclear fuel elements between the competitors, under different price and cost circumstances. The model shows that, if integrated and non-integrated competitors sell their final product at identical prices, the non-integrated manufacturer returns a net profit only 17% of the integrated firm. Also, the integrated supplier can price his product 35% below the non-integrated producer's price and still return the same net profit. Vertical integration confers a definite market advantage to the integrated supplier, and the basic source of that advantage is the cost-price differential of the raw material, uranium

Investigation of Vertical Microwave Publishing Caused by the Base Transceiver Station (BTS Antennas in Hashtgerd City

Directory of Open Access Journals (Sweden)

Simin Naseri

2013-12-01

Full Text Available Background and Objectives: New Hazards interface the environment and human life along with technology development. One of these pollutants is electromagnetic field and it’s known and unknown bad effects on the environment, this study determines the vertical publishing (height measurement of microwave antennas in the city of Hashtgerd. Methods: The basic information including the geographical location of the BTS antennas in the city, brand, the operator type, installation and its height was received from CRA and radio communications, and then the measuring was done by using the standard method of IEEE STD 95. 1 by the SPECTRAN 4060, and by using crane elevator in 17-meters height near the BTS antennas (15 meters.analysis were done by Spss16 and by Kolmogorov Smirnov test, multiple regression method. Results: Results show that in the both operators of Irancell and Hamrah-e-aval, density will increase by increasing measurement height or decreasing the vertical distance of broadcaster antenna. Regarding to the mix model test, a meaningful statistical relationship can be seen between measurement height and the density average in both types of the operators. Conclusion: while measuring height increased or in other words got closer to the antennas, density average increased in both operators, so the highest number was reported in the minimum vertical distance compared to the Irancell operator antenna was 25 mw/m2 and the lowest number was related to Hamrah-e-aval operator in the maximum vertical distance which was 0.02mw/m2. Thus, people stationed in the tall buildings parallel with installation height of antennas or in less vertical distance of them, are more exposed to the waves.

(Burnout Syndrome İn The Accounting Managers Of Lodging Operations)

OpenAIRE

Ersoy, Ayten; Utku, Burcu Demirel

2005-01-01

(Burnout Syndrome İn The Accounting Managers Of Lodging Operations) In this study, the burn-out levels of accounting managers working in 5 star hotels or 1st class holiday villages operating in Antalya region are examined in terms of some variables. The population of this research consists of "77" 5 star hotels, "60" 1st class holiday villages, in total "137" accounting managers. İn the scope of the research, 101 accounting managers chosen through random samplin...

Vertical displacement of the brain and the target area during open stereotaxic neurosurgery

International Nuclear Information System (INIS)

Wester, K.; Kraekenes, J.

2001-01-01

During stereotaxic thalamotomies, we observed that the brain surface was sinking. The study was carried out to investigate to what extent the target area also was displaced and how this would affect the accuracy of the stereotaxic procedure. In 12 thalamotomies, with the patients operated on in the sitting position, we found that the cortical surface sank 0-9 (mean 5) mm during the operation. The vertical co-ordinate of the thalamic target was consequently adjusted per-operatively, and the electrodes were advanced on additional distance of 1-5.5 (mean 3.5) mm in an attempt to compensate for the assumed sinking of the target. This per-operative adjustment was based on the surgeon's experience and the results of macro-stimulation studies. The exact location of the thalamotomy lesion, and thereby the accuracy of the adjustment, was evaluated on 3 months postoperative CT scans. These showed that the intended target was hit with a sufficient degree of accuracy in all the patients, although the vertical co-ordinate had been slightly over-adjusted, as the center of the lesion on the average was located 1 mm below the intended location. Thus, if the vertical position had not been adjusted, the lesion would on the average have been located 2.5 mm too high compared with the intended target. Patients undergoing thalamotomy and other stereotaxic procedures, where a high degree of accuracy is needed, should be operated on in the sitting position. At the thalamic level, the vertical displacement of the target should be adjusted for by additional advancement of the stereotaxic probe. On average, this compensatory adjustment should be about half the per-operative sinking of the cortical surface. (author)

Cryogenic system for the Energy Recovery Linac and vertical test facility at BNL

International Nuclear Information System (INIS)

Than, R.; Soria, V.; Lederle, D.; Orfin, P.; Porqueddu, R.; Talty, P.; Zhang, Y.; Tallerico, T.; Masi, L.

2011-01-01

A small cryogenic system and warm helium vacuum pumping system provides cooling to either the Energy Recovery Linac's (ERL) cryomodules that consist of a 5-cell cavity and an SRF gun or a large Vertical Test Dewar (VTD) at any given time. The cryogenic system consists of a model 1660S PSI piston plant, a 3800 liter storage dewar, subcooler, a wet expander, a 50 g/s main helium compressor, and a 170 m 3 storage tank. A system description and operating plan of the cryogenic plant and cryomodules is given. The cryogenic system for ERL and the Vertical Test Dewar has a plant that can produce the equivalent of 300W at 4.5K with the addition of a wet expander 350 W at 4.5K. Along with this system, a sub-atmospheric, warm compression system provides pumping to produce 2K at the ERL cryomodules or the Vertical Test Dewar. The cryogenic system for ERL and the Vertical Test Dewar makes use of existing equipment for putting a system together. It can supply either the ERL side or the Vertical Test Dewar side, but not both at the same time. Double valve isolation on the liquid helium supply line allows one side to be warmed to room temperature and worked on while the other side is being held at operating temperature. The cryogenic system maintain the end loads from 4.4K to 2K or colder depending on capacity. Liquid helium storage dewar capacity allows ERL or the VTD to operate above the plant's capacity when required and ERL cryomodules ballast reservoirs and VTD reservoir allows the end loads to operate on full vacuum pump capacity when required.

Heteroepitaxial Patterned Growth of Vertically Aligned and Periodically Distributed ZnO Nanowires on GaN Using Laser Interference Ablation

KAUST Repository

Yuan, Dajun

2010-08-23

A simple two-step method of fabricating vertically aligned and periodically distributed ZnO nanowires on gallium nitride (GaN) substrates is described. The method combines laser interference ablation (LIA) and low temperature hydrothermal decomposition. The ZnO nanowires grow heteroepitaxially on unablated regions of GaN over areas spanning 1 cm2, with a high degree of control over size, orientation, uniformity, and periodicity. High resolution transmission electron microscopy and scanning electron microscopy are utilized to study the structural characteristics of the LIA-patterned GaN substrate in detail. These studies reveal the possible mechanism for the preferential, site-selective growth of the ZnO nanowires. The method demonstrates high application potential for wafer-scale integration into sensor arrays, piezoelectric devices, and optoelectronic devices. © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Critical exponents for square lattice trails with a fixed number of vertices of degree 4

International Nuclear Information System (INIS)

James, E W; Soteros, C E

2002-01-01

We prove several previously conjectured results about the number of n-edge trails and n-edge embeddings of Eulerian graphs, each with a fixed number, k, of degree 4 vertices, in the lattice Z 2 . In particular, under the assumption that the relevant critical exponents exist, we prove that the difference between the critical exponent for closed trails (Eulerian graph embeddings) and that for self-avoiding circuits (polygons) is exactly k, the number of degree 4 vertices. Similarly, we prove that the difference between the critical exponent for either open trails or open Eulerian graph embeddings and that for self-avoiding walks is also k. These results are proved by establishing upper and lower bounds for the number of n-edge embeddings of closed (open) Eulerian graphs with k vertices of degree 4 in terms of the number of n-edge self-avoiding polygons (walks). The lower bounds are proved using a Kesten pattern theorem argument and the upper bounds are established by developing (based on a detailed case analysis) a method for removing vertices of degree 4 from an embedding by altering at most a constant (independent of n) number of vertices and edges of the embedding. The work presented here extends and improves the arguments first given in the work of Zhao and Lookman (1993 J. Phys. A: Math. Gen. 26 1067-76)

Some special values of vertices of trees on the suborbital graphs

Science.gov (United States)

Deǧer, A. H.; Akbaba, Ü.

2018-01-01

In the present study, the action of a congruence subgroup of S L(2, Z) on ℚ ^ is examined. From this action and its properties, vertices of paths of minimal length on the suborbital graph Fu,N give rise to some special sequence values, that are alternate sequences such as identity, Fibonacci and Lucas sequences. These types of vertices also give rise to special continued fractions, hence from recurrence relations for continued fractions, values of these vertices and values of special sequences were associated.

Gastroplastia vertical com desvio jejunoileal: novo procedimento técnico Vertical gastroplasty with jejunoileal bypass: new technical procedure

Directory of Open Access Journals (Sweden)

Bruno Zilberstein

2011-09-01

Full Text Available INTRODUÇÃO: A gastroplastia vertical é procedimento técnico cada vez mais utilizado no tratamento cirúrgico da obesidade mórbida, sendo empregado isoladamente ou como tempo cirúrgico do duodenal switch ou da bipartição intestinal (técnica de Santoro. Quando empregada isoladamente tem apenas caráter restritivo. MÉTODO: É proposta a associação do desvio jejunoileal à gastroplastia vertical, no sentido de conferir um componente metabólico ao procedimento e eventualmente potencializá-lo a médio e longo prazos. Foram operados oito pacientes com obesidade mórbida após a retirada da banda gástrica ajustável ou como procedimento primário associado à gastroplastia vertical e desvio jejunoileal através de anastomose laterolateral entre o jejuno a 80 cm do ângulo dudeno jejunal e o íleo a 120 cm da válvula ileocecal, por videolaparoscopia. RESULTADOS: Os pacientes evoluíram sem qualquer intercorrência tanto no trans como no pós-operatório imediato, e nos meses que se seguiram. A evolução do IMC médio, mostrou redução expressiva indo de 39,57 kg/m² para 28 kg/m². Nenhum paciente referiu diarréia ou qualquer quadro disabsortivo no período estudado. CONCLUSÃO: Pode-se oferecer nova opção terapêutica, com ação restritiva e metabólica, na qual não existem os inconvenientes do desvio do trânsito duodenal com todas suas consequências.INTRODUCTION: Vertical gastroplasty is increasingly used in the surgical treatment of morbid obesity, being used alone or as part of the duodenal switch surgery or even in intestinal bipartition (Santoro technique. When used alone has only a restrictive character. METHOD: Is proposed association of jejunoileal bypass to vertical gastroplasty, in order to give a metabolic component to the procedure and eventually empower it to medium and long term. Eight morbidly obese patients were operated after removal of adjustable gastric band or as a primary procedure associated to vertical

Solving vertical transport and chemistry in air pollution models

International Nuclear Information System (INIS)

Berkvens, P.J.F.; Botchev, M.A.; Verwer, J.G.; Krol, M.C.; Peters, W.

2000-01-01

For the time integration of stiff transport-chemistry problems from air pollution modelling, standard ODE solvers are not feasible due to the large number of species and the 3D nature. The popular alternative, standard operator splitting, introduces artificial transients for short-lived species. This complicates the chemistry solution, easily causing large errors for such species. In the framework of an operational global air pollution model, we focus on the problem formed by chemistry and vertical transport, which is based on diffusion, cloud-related vertical winds, and wet deposition. Its specific nature leads to full Jacobian matrices, ruling out standard implicit integration. We compare Strang operator splitting with two alternatives: source splitting and an (unsplit) Rosenbrock method with approximate matrix factorization, all having equal computational cost. The comparison is performed with real data. All methods are applied with half-hour time steps, and give good accuracies. Rosenbrock is the most accurate, and source splitting is more accurate than Strang splitting. Splitting errors concentrate in short-lived species sensitive to solar radiation and species with strong emissions and depositions. 30 refs

MHD stability of vertically asymmetric tokamak equilibria

International Nuclear Information System (INIS)

Dalhed, H.E.; Grimm, R.C.; Johnson, J.L.

1981-03-01

The ideal MHD stability properties of a special class of vertically asymmetric tokamak equilibria are examined. The calculations confirm that no major new physical effects are introduced and the modifications can be understood by conventional arguments. The results indicate that significant departures from up-down symmetry can be tolerated before the reduction in β becomes important for reactor operation

The analysis of the differences between the results of the thermal response test and the data from the operation of the brine-to-water heat pump’s vertical exchanger

Directory of Open Access Journals (Sweden)

Fidorów-Kaprawy Natalia

2017-01-01

Full Text Available The article discusses the principles and the problems of obtaining an accurate data input for the design of brine-to-water heat pump’s vertical exchangers. Currently, the most accurate method is the thermal response test (TRT. Unfortunately, the test procedure has its limitations and the quality of the results depends on many factors that cannot be fully controlled during the test. As an illustration of the problems, the results of the TRT were presented. The test was executed on the vertical boreholes (one actively regenerated and one not actively regenerated during the summer which are parts of the operating heat pump system. The test results were compared to the data from the device’s operation, in particular with the measurements of the undisturbed ground temperature profiles and the actual unit energy gains from the boreholes. The level of difference between the results of the test and the data from the operation of the boreholes under the real load and the threats concerning the boreholes overload were shown. Additionally the performance differences between the actively regenerated and not actively regenerated boreholes have been emphasised.

Developing and testing a vertical sintering furnace for remote nuclear applications

International Nuclear Information System (INIS)

Nesbitt, J.F.; Ryer, C.M.

1980-01-01

Horizontal-type furnaces used to sinter fuel pellets on a production basis are large and thus impractical for remote applications. However, research has shown that vertical-type furnaces are adaptable for use and are cheaper to operate and maintain. In 1979, Pacific Northwest Laboratory, working under the auspices of the Department of Energy's Fuel Refabrication and Development (FRAD) Program, began developing an advanced concept for a remotely operated furnace designed specifically to sinter nuclear fuel pellets. The FRAD Program at PNL ended before the sintering of nuclear fuels could be completely verified. However during 1979, PNL performed a sufficient number and variety of tests to establish that nuclear fuel pellets can be sintered in a vertical furnace

Ventajas de la perforación direccional: revisión y aplicación en el Oriente Ecuatoriano

Directory of Open Access Journals (Sweden)

Darío Cedeño Macías

2017-05-01

Full Text Available El avance evolutivo que ha tenido la industria hidrocarburífera a nivel mundial, específicamente en las operaciones de extracción y producción, requieren métodos más precisos y rigurosos para llevar a cabo su cometido, considerando principalmente la relación costo beneficio. Para ello es imperativo desarrollar tecnologías y sistemas de manera paralela a dicha evolución. El objetivo de este trabajo es presentar una revisión actualizada de los aspectos esenciales de la perforación direccional, con énfasis en sus evidentes ventajas respecto a la perforación vertical o convencional, y sobre todo su impacto en la reducción de costos para la industria petrolera. De manera que el nivel académico trabaje estrechamente con el nivel profesional, teniendo como parte medular el análisis de datos de ingeniería de diseño en los sistemas de perforación direccional rotativos y su impacto en la reducción de costos operativos en el proceso de extracción de hidrocarburos. Se presentan y discuten los resultados del desempeño alcanzado por estas herramientas en el campo.   Abstract The evolutionary advance of the hydrocarbon industry worldwide, specifically in the extraction and production operations, requires more precise and rigorous methods to carry out its mission, considering mainly the cost benefit relation. To do this, it is imperative to develop technologies and systems in parallel with this evolution. The objective of this work is to present an updated review of the essential aspects of directional drilling, with emphasis on its obvious advantages over vertical or conventional drilling, and especially its impact on reducing costs for the oil industry. So that the academic level works closely with the professional level, having as a core part the analysis of design engineering data in rotary directional drilling systems and its impact on the reduction of operating costs in the hydrocarbon extraction process. The results of the

Non-standard equipment for construction of vertical shafts

Science.gov (United States)

Yagodkin, F. I.; Prokopov, A. Y.; Pleshko, M. S.; Pankratenko, A. N.

2017-10-01

The article deals with the modern problems of construction and reconstruction of vertical shafts of mines, which require innovative technical solutions in the mechanization of mining operations. The examples developed by the authors of the original equipment and technologies, are successfully implemented for the mining industry in Russia.

Measurement of vertical stroke Vub vertical stroke using b hadron semileptonic decay

International Nuclear Information System (INIS)

Abbiendi, G.; Aakesson, P.F.

2001-01-01

The magnitude of the CKM matrix element vertical stroke V ub vertical stroke is determined by measuring the inclusive charmless semileptonic branching fraction of beauty hadrons at OPAL based on b → X u lν event topology and kinematics. This analysis uses OPAL data collected between 1991 and 1995, which correspond to about four million hadronic Z decays. We measure Br(b → X u lν) to be (1.63 ±0.53 +0.55 -0.62 ) x 10 -3 . The first uncertainty is the statistical error and the second is the systematic error. From this analysis, vertical stroke V ub vertical stroke is determined to be: vertical stroke V ub vertical stroke =(4.00±0.65(stat) +0.67 -0.76 (sys)±0.19(HQE)) x 10 -3 . The last error represents the theoretical uncertainties related to the extraction of vertical stroke V ub vertical stroke from Br(b→X u l ν) using the Heavy Quark Expansion. (orig.)

The Correlation of Smile Line with the Vertical Cephalometric Parameters of Anterior Facial Height

Directory of Open Access Journals (Sweden)

T. Hosseinzadeh–Nik

2005-03-01

Full Text Available Statement of the problem: In the evolution of orthodontics, the changes in soft tissue,especially smile line attracts considerable attention.Purpose: The present study was carried out to evaluate the correlation of the smile line with the vertical parameters of anterior part of face.Materials and Methods: Forty-six Iranian adults, aged between 18-25 years were selected. Five quantitative and three qualitative variables of smile analysis were recorded for each subject. Cephalometric analysis was carried out using angular and linear parameters. The correlations between smile line variables and cephalometric parameters were calculated using Spearman and Pearson’s correlation analyses.Results: The result of this study showed that the cephalometric parameters of N-Me,Pn-Line, N-B, N-Pg had significant correlations with quantitative variable of toothlower lip position. The P-values were P=0.003, P=0.027, P=0.006, P=0.002 respectively. N-Me, N-B, N-Pg represented significant correlations with interlabial gapon smile (P= 0.006, P=0.036, P=0.002 respectively. There was a significant correlation between N-Pg and quantitative factor of tooth-upper lip position (P=0.034. Upper incisor to palatal plane showed a significant correlation with qualitative variable oftooth-upper lip position (P=0.019, interlabial gap on smile (P=0.004, and tooth-upper lip position (P=0.006. Upper incisor to FH represented a reverse relation with incisal edge to lower lip (P=0.028.This parameter also showed significant correlations withquantitative factors of tooth-lower lip position (P=0.040 and crown height (P=0.002.Conclusions: According to the results of this study, it can be concluded that, linear skeletal and dental vertical factors affect the vertical features of smile. Angular vertical parameters, except gonial angle, influence the vertical position of smile.

New Urban Vertical Axis Wind Turbine Design

Directory of Open Access Journals (Sweden)

Alexandru-Mihai CISMILIANU

2015-12-01

Full Text Available This paper develops a different approach for enhancing the performance of Vertical Axis Wind Turbines for the use in the urban or rural environment and remote isolated residential areas. Recently the vertical axis wind turbines (VAWT have become more attractive due to the major advantages of this type of turbines in comparison to the horizontal axis wind turbines. We aim to enhance the overall performance of the VAWT by adding a second set of blades (3 x 2=6 blades following the rules of biplane airplanes. The model has been made to operate at a maximum power in the range of the TSR between 2 to 2.5. The performances of the VAWT were investigated numerically and experimentally and justify the new proposed design.

A low vertical β mode for the LNLS UVX electron storage ring

International Nuclear Information System (INIS)

Lin, Liu; Tavares, P.

1991-01-01

An operation mode with low vertical betatron function in one of the long dispersion free straight sections of the LNLS UVX Electron Storage Ring is studied for applications with small gap insertions. The flexibility of this lattice is analyzed regarding two aspects: the range of variation of the vertical betatron tune and the ability to set the betatron functions to high/low values in the insertion straights

Network access charges, vertical integration, and property rights structure - experiences from the German electricity markets

International Nuclear Information System (INIS)

Growitsch, C.; Wein, T.

2005-01-01

After the deregulation of the German electricity markets in 1998, the German government opted for a regulatory regime called negotiated third party access, which would be subject to ex-post control by the federal cartel office. Network access charges for new competitors are based on contractual arrangements between energy producers and industrial consumers. As the electricity networks are incontestable natural monopolies, the local and regional network operators are able to set (monopolistic) charges at their own discretion, restricted only by the possible interference of the federal cartel office (Bundeskartellamt). In this paper we analyze if there is evidence for varying charging behaviour depending on the supplier's economic independence (structure of property rights) or its level of vertical integration. For this purpose, we hypothesise that incorporated and vertically integrated suppliers set different charges than independent utility companies. Multivariate estimations show a relation between network access charges and the network operator's economic independence as well as level of vertical integration: on the low voltage level for an estimated annual consumption of 1700 kW/h, vertically integrated firms set-in accordance with our hypothesis-significantly lower access charges than vertically separated suppliers, whereas incorporated network operators charge significantly higher charges compared to independent suppliers. These results could not have been confirmed for other consumptions or voltage levels. (author)

Twist operator correlation functions in O(n) loop models

International Nuclear Information System (INIS)

Simmons, Jacob J H; Cardy, John

2009-01-01

Using conformal field theoretic methods we calculate correlation functions of geometric observables in the loop representation of the O(n) model at the critical point. We focus on correlation functions containing twist operators, combining these with anchored loops, boundaries with SLE processes and with double SLE processes. We focus further upon n = 0, representing self-avoiding loops, which corresponds to a logarithmic conformal field theory (LCFT) with c = 0. In this limit the twist operator plays the role of a 0-weight indicator operator, which we verify by comparison with known examples. Using the additional conditions imposed by the twist operator null states, we derive a new explicit result for the probabilities that an SLE 8/3 winds in various ways about two points in the upper half-plane, e.g. that the SLE passes to the left of both points. The collection of c = 0 logarithmic CFT operators that we use deriving the winding probabilities is novel, highlighting a potential incompatibility caused by the presence of two distinct logarithmic partners to the stress tensor within the theory. We argue that both partners do appear in the theory, one in the bulk and one on the boundary and that the incompatibility is resolved by restrictive bulk-boundary fusion rules

Carrier dynamics of InxGa1-xN/GaN multiple quantum wells grown on (−201) β-Ga2O3 for bright vertical light emitting diodes

KAUST Repository

Mumthaz Muhammed, Mufasila; Xu, Jian; Wehbe, Nimer; Roqan, Iman S.

2018-01-01

High-quality InxGa1-xN/GaN multi-quantum well (MQW) structures (0.05≤x≤0.13), are successfully grown on transparent and conductive (−201)-oriented β-Ga2O3 substrate. Scanning-transmission electron microscopy and secondary ion mass spectrometry (SIMS) show well-defined high quality MQWs, while the In and Ga compositions in the wells and the barriers are estimated by SIMS. Temperature-dependant Photoluminescence (PL) confirms high optical quality with a strong bandedge emission and negligble yellow band. time-resolved PL measurements (via above/below-GaN bandgap excitations) explain carrier dynamics, showing that the radiative recombination is predominant. Our results demonstrate that (−201)-oriented β-Ga2O3 is a strong candidate as a substrate for III-nitride-based vertical- emitting devices.

Carrier dynamics of InxGa1-xN/GaN multiple quantum wells grown on (−201) β-Ga2O3 for bright vertical light emitting diodes

KAUST Repository

Mumthaz Muhammed, Mufasila

2018-05-30

High-quality InxGa1-xN/GaN multi-quantum well (MQW) structures (0.05≤x≤0.13), are successfully grown on transparent and conductive (−201)-oriented β-Ga2O3 substrate. Scanning-transmission electron microscopy and secondary ion mass spectrometry (SIMS) show well-defined high quality MQWs, while the In and Ga compositions in the wells and the barriers are estimated by SIMS. Temperature-dependant Photoluminescence (PL) confirms high optical quality with a strong bandedge emission and negligble yellow band. time-resolved PL measurements (via above/below-GaN bandgap excitations) explain carrier dynamics, showing that the radiative recombination is predominant. Our results demonstrate that (−201)-oriented β-Ga2O3 is a strong candidate as a substrate for III-nitride-based vertical- emitting devices.

Vertical integration of dual wavelength index guided lasers

NARCIS (Netherlands)

Karouta, F.; Tan, H.H.; Jagadish, C.; Roy, van B.H.

1999-01-01

The vertical integration of two GaAs-based lasers operating at different wavelengths has been achieved with the use of re-growth technology. A V-channel substrate inner stripe structure was used for the bottom laser and a ridge waveguide for the top laser. Both lasers shared a common electrode and

Measurement of τ decays into a charged hadron accompanied by neutral π-mesons and determination of the CKM matrix element vertical stroke V{sub us} vertical stroke

Energy Technology Data Exchange (ETDEWEB)

Adametz, Aleksandra

2011-07-06

This thesis presents the branching fraction measurement of the τ{sup -}→K{sup -}(nπ{sup 0})ν{sub τ} (n=0,1,2,3) and τ{sup -}→π{sup -}(nπ{sup 0})ν{sub τ} (n=3,4) decays. The measurement is based on a data sample of 435 million τ pairs produced in e{sup +}e{sup -} collisions and collected with the BABAR detector in 1999-2008. The analysis is validated using precisely known τ decays as control modes. The measured branching fractions are B(τ{sup -}→K{sup -}ν{sub τ})=(7.100±0.033±0.156) x 10{sup -3}, B(τ{sup -}→K{sup -}π{sup 0}ν{sub τ})=(5.000±0.020±0.139) x 10{sup -3}, B(τ{sup -}→K{sup -}(2π{sup 0})ν{sub τ})=(5.654±0.144±0.323) x 10{sup -4}, B(τ{sup -}→K{sup -}(3π{sup 0})ν{sub τ})=(1.642±0.279±0.375) x 10{sup -4}, B(τ{sup -}→π{sup -}(3π{sup 0})ν{sub τ})=(1.216±0.010±0.047) x 10{sup -2}, B(τ{sup -}→π{sup -}(4π{sup 0})ν{sub τ})=(1.041±0.067±0.090) x 10{sup -3}, where the first uncertainty is statistical and the second systematic. The branching fraction B(τ{sup -}→π{sup -}(4π{sup 0})ν{sub τ}) is measured for the first time. The precision of the results is comparable or significantly improved with respect to previous measurements. The branching fraction B(τ{sup -}→K{sup -}ν{sub τ}) is combined with a lattice QCD calculation of the kaon decay constant to obtain the Cabibbo-Kobayashi-Maskawa matrix element vertical stroke V{sub us} vertical stroke =0.2224±0.0025(exp)±0.0029(theo). The branching fractions of the τ decays into a kaon are combined with the current world averages. The resulting averages are used in the determination of the total τ branching fraction, B{sub s}, into strangeness vertical stroke S vertical stroke =1 final states. B{sub s} is used in conjunction with vertical stroke V{sub ud} vertical stroke and a small SU(3)-symmetry breaking correction to compute vertical stroke V{sub us} vertical stroke =0.2176±0.0025(exp)±0.0010(theo).

Synthesis and electrical characterization of vertically-aligned ZnO–CuO hybrid nanowire p–n junctions

International Nuclear Information System (INIS)

Pukird, Supakorn; Song, Wooseok; Noothongkaew, Suttinart; Kim, Seong Ku; Min, Bok Ki; Kim, Seong Jun; Kim, Ki Woong; Myung, Sung; An, Ki-Seok

2015-01-01

Highlights: • Vertically-aligned ZnO–CuO hybrid nanowire arrays were synthesized by a two-step thermal chemical vapor deposition process. • The diameter of parallel-connected ZnO and CuO NWs were estimated to be 146 ± 12 nm and 55 ± 11 nm, respectively, and the formation of high-quality hexagonal ZnO and monoclinic CuO NWs were observed. • Clear rectifying behavior related with thermionic emission of carriers and the presence of an electrical potential barrier between the ZnO and CuO NWs were observed. - Abstract: In order to form nanowire (NW)-based p–n junctions, vertically-aligned ZnO–CuO hybrid NW arrays were synthesized by a two-step thermal chemical vapor deposition process. The diameter of parallel-connected ZnO and CuO NWs were estimated to be 146 ± 12 nm and 55 ± 11 nm, respectively, as observed by scanning electron microscopy. Chemical and structural characterizations of ZnO–CuO hybrid NW arrays were performed using X-ray photoelectron spectroscopy and X-ray diffraction, resulting in the formation of high-quality hexagonal ZnO and monoclinic CuO NWs. The temperature dependence of I–V curves and impedance spectra suggested that clear rectifying behavior related with thermionic emission of carriers and the presence of an electrical potential barrier between the ZnO and CuO NWs

Vertical-cavity laser with a novel grating mirror

DEFF Research Database (Denmark)

Park, Gyeong Cheol

Hybrid III-V on silicon (Si) ‘vertical cavity lasers’ (hybrid VCLs), which can emit light laterally into a Si waveguide, are fabricated and investigated. The Si-integrated hybrid VCL consists of a top dielectric Bragg reflector (DBR), a III-V active layer, and a bottom high contrast grating (HCG...... the vertical cavity laterally into the Si waveguide. The measured inplane emission proves the lasing action with a side-mode suppression ratio (SMSR) of 27.5 dB at a peak wavelength of 1486 nm. The threshold pumping power corresponds to a current injection of 1.1 mA. A signature of highly anisotropic cavity...... dispersion has been observed and discussed, which is unique for HCG-based vertical cavities. The second version proves the potential for high-speed operation of hybrid VCL structure. In the hybrid VCL structure, the effective cavity length is substantially reduced by using a dielectric DBR and a TM...

Elimination of macrostep-induced current flow nonuniformity in vertical GaN PN diode using carbon-free drift layer grown by hydride vapor phase epitaxy

Science.gov (United States)

Fujikura, Hajime; Hayashi, Kentaro; Horikiri, Fumimasa; Narita, Yoshinobu; Konno, Taichiro; Yoshida, Takehiro; Ohta, Hiroshi; Mishima, Tomoyoshi

2018-04-01

In vertical GaN PN diodes (PNDs) grown entirely by metal–organic chemical vapor deposition (MOCVD), large current nonuniformity was observed. This nonuniformity was induced by macrosteps on the GaN surface through modulation of carbon incorporation into the n-GaN crystal. It was eliminated in a hybrid PND consisting of a carbon-free n-GaN layer grown by hydride vapor phase epitaxy (HVPE) and an MOCVD-regrown p-GaN layer. The hybrid PND showed a fairly low on-resistance (2 mΩ cm2) and high breakdown voltage (2 kV) even without a field plate electrode. These results clearly indicated the strong advantages of the HVPE-grown drift layer for improving power device performance, uniformity, and yield.

MÉTODO SIMPLIFICADO PARA LA ESTIMACIÓN DE LA CARGA ÚLTIMA DE PILOTES SOMETIDOS A CARGA VERTICAL AXIAL EN ARENAS

Directory of Open Access Journals (Sweden)

Edgar Giovanny Dias Segura

2013-01-01

Full Text Available La respuesta de diferentes pilotes sometidos a carga vertical axial fue estudiada empleando una serie de análisis mediante elementos finitos, considerando como suelo de fundación diez tipos de arenas en condición seca y saturada. A partir de los resultados obtenidos, se propone un método simplificado para estimar la carga última en pilotes preexcavados sobre arenas, en términos del diámetro y enterramiento del pilote, peso unitario del suelo, condiciones de saturación, y mediciones indirectas de la resistencia al corte del suelo, obtenidas a partir de la densidad relativa y el índice de penetración SPT. El método propuesto, basado en 180 casos analizados, ofrece una precisión de 92%, y constituye una herramienta complementaría de diseño para estimar la carga última de pilotes preexcavados en arenas.

Wilson loops and its correlators with chiral operators in N = 2, 4 SCFT at large N

Science.gov (United States)

Sysoeva, E.

2018-03-01

In this paper we compute the vacuum expectation value of the Wilson loop and its correlators with chiral primary operators in N = 2, 4 superconformal U( N ) gauge theories at large N . After localization these quantities can be computed in terms of a deformed U( N ) matrix model. The Wilson loops we deal with are in the fundamental and symmetric representations.

The exact effective couplings of 4D N=2 gauge theories

Energy Technology Data Exchange (ETDEWEB)

Mitev, Vladimir [Humboldt-Universitaet, Berlin (Germany). Inst. fuer Mathematik; Humboldt-Universitaet, Berlin (Germany). Inst. fuer Physik; Pomoni, Elli [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); National Technical Univ. Athens (Greece). Physics Division

2014-07-15

The anomalous dimensions of operators in the purely gluonic SU(2,1 vertical stroke 2) sector of any planar conformal N=2 theory can be read off from the N=4 SYM results by replacing the N=4 coupling constant by an interpolating function of the N=2 coupling constants, to which we refer to as the effective coupling. For a large class of N=2 theories we compute the weak coupling expansion of these functions as well as the leading strong coupling term by employing supersymmetric localization. Via Feynman diagrams, we interpret our results as the relative (between N=2 and N=4) finite renormalization of the coupling constant. Using the AdS/CFT dictionary, we identify the effective couplings with the effective string tensions of the corresponding gravity dual theories. Thus, any observable in the SU(2,1 vertical stroke 2) sector can be obtained from its N=4 counterpart by replacing the N=4 coupling constant by the universal, for a given theory, effective coupling.

The exact effective couplings of 4D N=2 gauge theories

International Nuclear Information System (INIS)

Mitev, Vladimir; Humboldt-Universitaet, Berlin; Pomoni, Elli; National Technical Univ. Athens

2014-07-01

The anomalous dimensions of operators in the purely gluonic SU(2,1 vertical stroke 2) sector of any planar conformal N=2 theory can be read off from the N=4 SYM results by replacing the N=4 coupling constant by an interpolating function of the N=2 coupling constants, to which we refer to as the effective coupling. For a large class of N=2 theories we compute the weak coupling expansion of these functions as well as the leading strong coupling term by employing supersymmetric localization. Via Feynman diagrams, we interpret our results as the relative (between N=2 and N=4) finite renormalization of the coupling constant. Using the AdS/CFT dictionary, we identify the effective couplings with the effective string tensions of the corresponding gravity dual theories. Thus, any observable in the SU(2,1 vertical stroke 2) sector can be obtained from its N=4 counterpart by replacing the N=4 coupling constant by the universal, for a given theory, effective coupling.

Measurement of the CKM matrix element vertical stroke Vts vertical stroke 2

International Nuclear Information System (INIS)

Unverdorben, Christopher Gerhard

2015-03-01

This is the first direct measurement of the CKM matrix element vertical stroke V ts vertical stroke, using data collected by the ATLAS detector in 2012 at √(s)= 8 TeV pp-collisions with a total integrated luminosity of 20.3 fb -1 . The analysis is based on 112 171 reconstructed t anti t candidate events in the lepton+jets channel, having a purity of 90.0 %. 183 t anti t→W + W - b anti s decays are expected (charge conjugation implied), which are available for the extraction of the CKM matrix element vertical stroke V ts vertical stroke 2 . To identify these rare decays, several observables are examined, such as the properties of jets, tracks and of b-quark identification algorithms. Furthermore, the s-quark hadrons K 0 s are considered, reconstructed by a kinematic fit. The best observables are combined in a multivariate analysis, called ''boosted decision trees''. The responses from Monte Carlo simulations are used as templates for a fit to data events yielding a significance value of 0.7σ for t→s+W decays. An upper limit of vertical stroke V ts vertical stroke 2 <1.74 % at 95 % confidence level is set, including all systematic and statistical uncertainties. So this analysis, using a direct measurement of the CKM matrix element vertical stroke V ts vertical stroke 2 , provides the best direct limit on vertical stroke V ts vertical stroke 2 up to now.

Non-axisymmetric simulation of the vertical displacement event in tokamaks

International Nuclear Information System (INIS)

Lim, Y.Y.; Lee, J.K.; Shin, K.J.; Hur, M.S.

1999-01-01

Tokamak plasmas with highly elongated cross sections are subject to a vertical displacement event (VDE). The nonlinear magnetohydrodynamic (MHD) evolutions of tokamak plasmas during the VDE are simulated by a three-dimensional MHD code as a combination of N=0 and N=1 components. The nonlinear evolution during the VDE is strongly affected by the relative amplitude of the N=1 to the N=0 modes. (author)

Surprises from the resolution of operator mixing in N=4 SYM

International Nuclear Information System (INIS)

Bianchi, Massimo; Rossi, Giancarlo; Stanev, Yassen S.

2004-01-01

We reexamine the problem of operator mixing in N=4 SYM. Particular attention is paid to the correct definition of composite gauge invariant local operators, which is necessary for the computation of their anomalous dimensions beyond lowest order. As an application we reconsider the case of operators with naive dimension Δ 0 =4, already studied in the literature. Stringent constraints from the resummation of logarithms in power behaviours are exploited and the role of the generalized N=4 Konishi anomaly in the mixing with operators involving fermions is discussed. A general method for the explicit (numerical) resolution of the operator mixing and the computation of anomalous dimensions is proposed. We then resolve the order g 2 mixing for the 15 (purely scalar) singlet operators of naive dimension Δ 0 =6. Rather surprisingly we find one isolated operator which has a vanishing anomalous dimension up to order g 4 , belonging to an apparently long multiplet. We also solve the order g 2 mixing for the 26 operators belonging to the representation 20' of SU(4). We find an operator with the same one-loop anomalous dimension as the Konishi multiplet

clınıcal EVALUATION OF FREE GINGIVAL GRAFT SHRINKAGE IN HORIZONTAL AND VERTICAL DIMENSIONS

Directory of Open Access Journals (Sweden)

Emine ÇİFCİBAŞI

2015-10-01

Full Text Available Purpose: To assess the shrinkage of Free Gingival Graft (FGG in horizontal and vertical dimensions and calculate the changes in the surface area of the transplanted tissue in a 3 months period. Materials and Methods: A total of 30 FGG were placed aiming to increase attached gingiva around recession sites. Vertical recessions, horizontal recessions, surface area, plaque index, gingival index, periodontal probing depth and clinical attachment level were assesed at baseline, 1 and 3 months postoperatively. Results: Graft shrinkage between baseline and 1 month was more evident than 1 to 3 months in either dimensions. Both horizontal and vertical dimensions were significantly decreased (p0.05. . Conclusion: The shrinkage of vertical and horizontal dimensions of the grafts were almost equal unlike the literature. In addition, the different dimensional changes observed in individual level deserve further research.

Characteristics of Vertical Mantle Heat Exchangers for Solar Water Heaters

DEFF Research Database (Denmark)

Shah, Louise Jivan; Morrison, G.L.; Behnia, M.

1999-01-01

- The flow structure in vertical mantle heat exchangers was investigated using a full-scale tank designed to facilitate flow visualisation. The flow structure and velocities in the mantle were measured using a particle Image Velocimetry (PIV) system. A CFD simulation model of vertical mantle heat...... exchangers was also developed for detailed evaluation of the heat flux distribution over the mantle surface. Both the experimental and simulation results indicate that distribution of the flow around the mantle gap is governed by buoyancy driven recirculation in the mantle. The operation of the mantle...

Simulation of zincblende AlGaN/GaN high electron mobility transistors for normally-off operation

Science.gov (United States)

Grady, R.; Bayram, C.

2017-07-01

In this work we investigate design parameters enabling normally-off operation of zincblende (ZB-) phase Al X Ga(1-X)N/GaN high electron mobility transistors (HEMTs) via Synopsys Sentaurus Technology Computer Aided Design (TCAD). As ZB-phase III-nitrides are polarization-free, the 2D electron gas (2DEG) channel at the Al X Ga(1-X)N/GaN heterojunction is formed through intentional δ-doping part of the Al X Ga(1-X)N barrier layer. The impact of each of the design parameters (i.e. Al-content and thickness of Al X Ga(1-X)N barrier; δ-doping location (within the Al X Ga(1-X)N barrier), δ-doped Al X Ga(1-X)N layer thickness and its doping amount; gate metal) are studied in detail and design trade-offs are reported. We show that work function of the gate metal impacts normally-off behavior and turn-on voltage considerably. Our results suggest that Al-content of 35% or less in the Al X Ga(1-X)N barrier results in a normally-off behavior whereas Al X Ga(1-X)N barrier thickness is effective in controlling the turn-on voltage. Overall, we provide design guidelines in controlling the normally-on/-off operation, threshold voltage, and 2DEG density in ZB-phase AlGaN/GaN HEMT technology.

Toward the 5nm technology: layout optimization and performance benchmark for logic/SRAMs using lateral and vertical GAA FETs

Science.gov (United States)

Huynh-Bao, Trong; Ryckaert, Julien; Sakhare, Sushil; Mercha, Abdelkarim; Verkest, Diederik; Thean, Aaron; Wambacq, Piet

2016-03-01

In this paper, we present a layout and performance analysis of logic and SRAM circuits for vertical and lateral GAA FETs using 5nm (iN5) design rules. Extreme ultra-violet lithography (EUVL) processes are exploited to print the critical features: 32 nm gate pitch and 24 nm metal pitch. Layout architectures and patterning compromises for enabling the 5nm node will be discussed in details. A distinct standard-cell template for vertical FETs is proposed and elaborated for the first time. To assess electrical performances, a BSIM-CMG model has been developed and calibrated with TCAD simulations, which accounts for the quasi-ballistic transport in the nanowire channel. The results show that the inbound power rail layout construct for vertical devices could achieve the highest density while the interleaving diffusion template can maximize the port accessibility. By using a representative critical path circuit of a generic low power SoCs, it is shown that the VFET-based circuit is 40% more energy efficient than LFET designs at iso-performance. Regarding SRAMs, benefits given by vertical channel orientation in VFETs has reduced the SRAM area by 20%~30% compared to lateral SRAMs. A double exposures with EUV canner is needed to reach a minimum tip-to-tip (T2T) of 16 nm for middle-of-line (MOL) layers. To enable HD SRAMs with two metal layers, a fully self-aligned gate contact for LFETs and 2D routing of the top electrode for VFETs are required. The standby leakage of vertical SRAMs is 4~6X lower than LFET-based SRAMs at iso-performance and iso-area. The minimum operating voltage (Vmin) of vertical SRAMs is 170 mV lower than lateral SRAMs. A high-density SRAM bitcell of 0.014 um2 can be obtained for the iN5 technology node, which fully follows the SRAM scaling trend for the 45nm nodes and beyond.

The elliptic quantum algebra Uq,p(sl-hatN) and its vertex operators

International Nuclear Information System (INIS)

Chang Wenjing; Ding Xiangmao

2009-01-01

We construct a realization of the elliptic quantum algebra U q,p (sl-hat N ) for any given level k in terms of free boson fields and their twisted partners. It can be considered as the elliptic deformation of the Wakimoto realization of the quantum affine algebra U q (sl-hat N ). We also construct a family of screening currents, which commute with the currents of U q,p (sl-hat N ) up to total q-differences. And we give explicit twisted expressions for the type I and type II vertex operators of U q,p (sl-hat N ) by twisting the known results of the type I vertex operators of the quantum affine algebra U q (sl-hat N ) and the new results of the type II vertex operators of U q (sl-hat N ) we obtained in this paper.

Fabrication, characterization and applications of flexible vertical InGaN micro-light emitting diode arrays.

Science.gov (United States)

Tian, Pengfei; McKendry, Jonathan J D; Gu, Erdan; Chen, Zhizhong; Sun, Yongjian; Zhang, Guoyi; Dawson, Martin D; Liu, Ran

2016-01-11

Flexible vertical InGaN micro-light emitting diode (micro-LED) arrays have been fabricated and characterized for potential applications in flexible micro-displays and visible light communication. The LED epitaxial layers were transferred from initial sapphire substrates to flexible AuSn substrates by metal bonding and laser lift off techniques. The current versus voltage characteristics of flexible micro-LEDs degraded after bending the devices, but the electroluminescence spectra show little shift even under a very small bending radius 3 mm. The high thermal conductivity of flexible metal substrates enables high thermal saturation current density and high light output power of the flexible micro-LEDs, benefiting the potential applications in flexible high-brightness micro-displays and high-speed visible light communication. We have achieved ~40 MHz modulation bandwidth and 120 Mbit/s data transmission speed for a typical flexible micro-LED.

Effect of Vertical, Horizontal, and Combined Plyometric Training on Explosive, Balance, and Endurance Performance of Young Soccer Players.

Science.gov (United States)

Ramírez-Campillo, Rodrigo; Gallardo, Francisco; Henriquez-Olguín, Carlos; Meylan, Cesar M P; Martínez, Cristian; Álvarez, Cristian; Caniuqueo, Alexis; Cadore, Eduardo L; Izquierdo, Mikel

2015-07-01

The aim of this study was to compare the effects of 6 weeks of vertical, horizontal, or combined vertical and horizontal plyometric training on muscle explosive, endurance, and balance performance. Forty young soccer players aged between 10 and 14 years were randomly divided into control (CG; n = 10), vertical plyometric group (VG; n = 10), horizontal plyometric group (HG; n = 10), and combined vertical and horizontal plyometric group (VHG; n = 10). Players performance in the vertical and horizontal countermovement jump with arms, 5 multiple bounds test (MB5), 20-cm drop jump reactive strength index (RSI20), maximal kicking velocity (MKV), sprint, change of direction speed (CODS), Yo-Yo intermittent recovery level 1 test (Yo-Yo IR1), and balance was measured. No significant or meaningful changes in the CG, apart from small change in the Yo-Yo IR1, were observed while all training programs resulted in meaningful changes in explosive, endurance, and balance performance. However, only VHG showed a statistically significant (p ≤ 0.05) increase in all performance test and most meaningful training effect difference with the CG across tests. Although no significant differences in performance changes were observed between experimental groups, the VHG program was more effective compared with VG (i.e., jumps, MKV, sprint, CODS, and balance performance) and HG (i.e., sprint, CODS, and balance performance) to small effect. The study demonstrated that vertical, horizontal, and combined vertical and horizontal jumps induced meaningful improvement in explosive actions, balance, and intermittent endurance capacity. However, combining vertical and horizontal drills seems more advantageous to induce greater performance improvements.

Vertices in the abelized picture

International Nuclear Information System (INIS)

Embacher, F.

1990-01-01

Covariant vertices of open bosonic string theory are transformed to the abelized picture. The way the pure transverse (light-cone gauge) vertex is contained therein is exhibited explicitly. The formalism shows in a quite transparent way that all further content of a covariant vertex is of gauge type. By applying the transverse projection operator in the abelized picture, an algebraic condition whether a set of Neumann coefficients define a vertex for string theory is obtained. A speculation concerning field redefinitions in string field theory is added. (Author) 33 refs

Development concepts of a Smart Cyber Operating Theater (SCOT) using ORiN technology.

Science.gov (United States)

Okamoto, Jun; Masamune, Ken; Iseki, Hiroshi; Muragaki, Yoshihiro

2018-02-23

Currently, networking has not progressed in the treatment room. Almost every medical device in the treatment room operates as a stand-alone device. In this project, we aim to develop a networked operating room called "Smart Cyber Operating Theater (SCOT)". Medical devices are connected using Open Resource interface for the Network (ORiN) technology. In this paper, we describe the concept of the SCOT project. SCOT is integrated using the communication interface ORiN, which was originally developed for industry. One feature of ORiN is that the system can be constructed flexibly. ORiN creates abstracts of the same type of devices and increases the robustness of the system for device exchange. By using ORiN technology, we are developing new applications, such as decision-making navigation or a precision guided treatment system.

A sampling device for counting insect egg clusters and measuring vertical distribution of vegetation

Science.gov (United States)

Robert L. Talerico; Robert W., Jr. Wilson

1978-01-01

The use of a vertical sampling pole that delineates known volumes and position is illustrated and demonstrated for counting egg clusters of N. sertifer. The pole can also be used to estimate vertical and horizontal coverage, distribution or damage of vegetation or foliage.

CONDENSATION OF WATER VAPOR IN A VERTICAL TUBE CONDENSER

Directory of Open Access Journals (Sweden)

Jan Havlík

2015-10-01

Full Text Available This paper presents an analysis of heat transfer in the process of condensation of water vapor in a vertical shell-and-tube condenser. We analyze the use of the Nusselt model for calculating the condensation heat transfer coefficient (HTC inside a vertical tube and the Kern, Bell-Delaware and Stream-flow analysis methods for calculating the shell-side HTC from tubes to cooling water. These methods are experimentally verified for a specific condenser of waste process vapor containing air. The operating conditions of the condenser may be different from the assumptions adopted in the basic Nusselt theory. Modifications to the Nusselt condensation model are theoretically analyzed.

Simulation of zincblende AlGaN/GaN high electron mobility transistors for normally-off operation

International Nuclear Information System (INIS)

Grady, R; Bayram, C

2017-01-01

In this work we investigate design parameters enabling normally-off operation of zincblende (ZB-) phase Al X Ga (1−X) N/GaN high electron mobility transistors (HEMTs) via Synopsys Sentaurus Technology Computer Aided Design (TCAD). As ZB-phase III-nitrides are polarization-free, the 2D electron gas (2DEG) channel at the Al X Ga (1−X) N/GaN heterojunction is formed through intentional δ -doping part of the Al X Ga (1−X) N barrier layer. The impact of each of the design parameters (i.e. Al-content and thickness of Al X Ga (1−X) N barrier; δ -doping location (within the Al X Ga (1−X) N barrier), δ-doped Al X Ga (1−X) N layer thickness and its doping amount; gate metal) are studied in detail and design trade-offs are reported. We show that work function of the gate metal impacts normally-off behavior and turn-on voltage considerably. Our results suggest that Al-content of 35% or less in the Al X Ga (1−X) N barrier results in a normally-off behavior whereas Al X Ga (1−X) N barrier thickness is effective in controlling the turn-on voltage. Overall, we provide design guidelines in controlling the normally-on/-off operation, threshold voltage, and 2DEG density in ZB-phase AlGaN/GaN HEMT technology. (paper)

X-ray of the stomach after vertical gastroplasty in the treatment of obesity

International Nuclear Information System (INIS)

Ovchinnikov, V.I.; Lipko, N.S.; Yashkov, Yu.I.; Timoshin, A.D.; Movchun, A.A; Oppel', T.A.

1996-01-01

The operation vertical gastroplasty is used to treat the socalled morbid obesity. It ends with the formation of a small stomach, Some experience gained with X-ray of the stomach is analyzed in 17 patients undergone vertical gastroplasty. X-ray evaluated the status of the small stomach arranged as a tube in the upper portions in the vicinity of the lesser curvature of the stomach. The shape, sizes, outlet of the small stomach, as well as emptying rates and the state of an internal vertical suture of the stomach are to be studies. 8 refs., 4 figs

The construction and operating characteristics of a cathode strip chamber system designed to measure the reaction vertices of a stopping kaon beam

International Nuclear Information System (INIS)

M.W. Ahmed; D. Androic; I. Bertovic; J. Bjoraker; R. Chrien; X. Cui; D. Dehnhard; Anton Empl; M. Furic; J. Gerald; R. Gill; E.V. Hungerford; H. Jungst; K.J. Lan; Jinghua Liu; C.L. Morris; J.M. O'Donnell; J.C. Peng; T. Petkovic; P. Pile; M. Planinic; C.M. Riedel; A. Rusek; R. Sutter; Liguang Tang; H.A. Thiessen; M. Youn; V. Zeps

2001-01-01

The design, construction, and performance of a segmented-target, cathode-strip, tracking-detector is discussed. The chamber was made of low-Z materials in order to allow photons to leave the target region. It was used to determine the reaction vertex of stopping kaons, and was successfully operated in a high-intensity kaon beamline at the Alternating Gradient Synchrotron at Brookhaven National Laboratory. The vertical and horizontal resolutions of the stopping kaon reaction positions were sigma X∼ 0.454mm and sigma Y∼ 1.180mm, respectively. The uncertainty in the longitudinal (Z) direction is given by one-half the thickness of a target segment

The construction and operating characteristics of a cathode strip chamber system designed to measure the reaction vertices of a stopping kaon beam

International Nuclear Information System (INIS)

Ahmed, M.W.; Androic, D.; Bertovic, I.; Bjoraker, J.; Chrien, R.; Cui, X.; Dehnhard, D.; Empl, A.; Furic, M.; Gerald, J.; Gill, R.; Hungerford, E.V.; Juengst, H.; Lan, K.J.; Liu, J.H.; Morris, C.L.; O'Donnell, J.M.; Peng, J.C.; Petkovic, T.; Pile, P.; Planinic, M.; Riedel, C.M.; Rusek, A.; Sutter, R.; Tang, L.; Thiessen, H.A.; Youn, M.; Zeps, V.

2001-01-01

The design, construction, and performance of a segmented-target, cathode-strip, tracking-detector is discussed. The chamber was made of low-Z materials in order to allow photons to leave the target region. It was used to determine the reaction vertex of stopping kaons, and was successfully operated in a high-intensity kaon beamline at the Alternating Gradient Synchrotron at Brookhaven National Laboratory. The vertical and horizontal resolutions of the stopping kaon reaction positions were σ X ∼0.454 mm and σ Y ∼1.180 mm, respectively. The uncertainty in the longitudinal (Z) direction is given by one-half the thickness of a target segment

The construction and operating characteristics of a cathode strip chamber system designed to measure the reaction vertices of a stopping kaon beam

CERN Document Server

Ahmed, M W; Bertovic, I; Bjoraker, J; Chrien, R; Cui, X; Dehnhard, D; Empl, A; Furic, M; Gerald, J; Gill, R; Hungerford, E V; Juengst, H; Lan, K J; Liu, J H; Morris, C L; O'donnell, J M; Peng, J C; Petkovic, T; Pile, P; Planinic, M; Riedel, C M; Rusek, A; Sutter, R; Tang, L; Thiessen, H A; Youn, M; Zeps, V

2001-01-01

The design, construction, and performance of a segmented-target, cathode-strip, tracking-detector is discussed. The chamber was made of low-Z materials in order to allow photons to leave the target region. It was used to determine the reaction vertex of stopping kaons, and was successfully operated in a high-intensity kaon beamline at the Alternating Gradient Synchrotron at Brookhaven National Laboratory. The vertical and horizontal resolutions of the stopping kaon reaction positions were sigma sub X approx 0.454 mm and sigma sub Y approx 1.180 mm, respectively. The uncertainty in the longitudinal (Z) direction is given by one-half the thickness of a target segment.

Potentially of using vertical and three dimensional isolation systems in nuclear structures

Energy Technology Data Exchange (ETDEWEB)

Zhou, Zhiuang [Research Institute of Structural Engineering and Disaster Reduction, Tongji University, Shanghai (China); Wong, Jenna [Lawrence Berkeley National Laboratories, Berkeley (United States); Mahin, Stephen [University of California, Berkeley (United States)

2016-10-15

Although the horizontal component of an earthquake response can be significantly reduced through the use of conventional seismic isolators, the vertical component of excitation is still transmitted directly into the structure. Records from instrumented structures, and some recent tests and analyses have actually seen increases in vertical responses in base isolated structures under the combined effects of horizontal and vertical ground motions. This issue becomes a great concern to facilities such as a Nuclear Power Plants (NPP), with specialized equipment and machinery that is not only expensive, but critical to safe operation. As such, there is considerable interest worldwide in vertical and three-dimensional (3D) isolation systems. This paper examines several vertical and 3D isolation systems that have been proposed and their potential application to modern nuclear facilities. In particular, a series of case study analyses of a modern NPP model are performed to examine the benefits and challenges associated with 3D isolation compared with horizontal isolation. It was found that compared with the general horizontal isolators, isolators that have vertical frequencies of no more than 3 Hz can effectively reduce the vertical in-structure responses for the studied NPP model. Among the studied cases, the case that has a vertical isolation frequency of 3 Hz is the one that can keep the horizontal period of the isolators as the first period while having the most flexible vertical isolator properties. When the vertical frequency of isolators reduces to 1 Hz, the rocking effect is obvious and rocking restraining devices are necessary.

Potentially of using vertical and three dimensional isolation systems in nuclear structures

International Nuclear Information System (INIS)

Zhou, Zhiuang; Wong, Jenna; Mahin, Stephen

2016-01-01

Although the horizontal component of an earthquake response can be significantly reduced through the use of conventional seismic isolators, the vertical component of excitation is still transmitted directly into the structure. Records from instrumented structures, and some recent tests and analyses have actually seen increases in vertical responses in base isolated structures under the combined effects of horizontal and vertical ground motions. This issue becomes a great concern to facilities such as a Nuclear Power Plants (NPP), with specialized equipment and machinery that is not only expensive, but critical to safe operation. As such, there is considerable interest worldwide in vertical and three-dimensional (3D) isolation systems. This paper examines several vertical and 3D isolation systems that have been proposed and their potential application to modern nuclear facilities. In particular, a series of case study analyses of a modern NPP model are performed to examine the benefits and challenges associated with 3D isolation compared with horizontal isolation. It was found that compared with the general horizontal isolators, isolators that have vertical frequencies of no more than 3 Hz can effectively reduce the vertical in-structure responses for the studied NPP model. Among the studied cases, the case that has a vertical isolation frequency of 3 Hz is the one that can keep the horizontal period of the isolators as the first period while having the most flexible vertical isolator properties. When the vertical frequency of isolators reduces to 1 Hz, the rocking effect is obvious and rocking restraining devices are necessary

Potentiality of Using Vertical and Three-Dimensional Isolation Systems in Nuclear Structures

Directory of Open Access Journals (Sweden)

Zhiguang Zhou

2016-10-01

Full Text Available Although the horizontal component of an earthquake response can be significantly reduced through the use of conventional seismic isolators, the vertical component of excitation is still transmitted directly into the structure. Records from instrumented structures, and some recent tests and analyses have actually seen increases in vertical responses in base isolated structures under the combined effects of horizontal and vertical ground motions. This issue becomes a great concern to facilities such as a Nuclear Power Plants (NPP, with specialized equipment and machinery that is not only expensive, but critical to safe operation. As such, there is considerable interest worldwide in vertical and three-dimensional (3D isolation systems. This paper examines several vertical and 3D isolation systems that have been proposed and their potential application to modern nuclear facilities. In particular, a series of case study analyses of a modern NPP model are performed to examine the benefits and challenges associated with 3D isolation compared with horizontal isolation. It was found that compared with the general horizontal isolators, isolators that have vertical frequencies of no more than 3 Hz can effectively reduce the vertical in-structure responses for the studied NPP model. Among the studied cases, the case that has a vertical isolation frequency of 3 Hz is the one that can keep the horizontal period of the isolators as the first period while having the most flexible vertical isolator properties. When the vertical frequency of isolators reduces to 1 Hz, the rocking effect is obvious and rocking restraining devices are necessary.

High-Efficiency InGaN/GaN Quantum Well-Based Vertical Light-Emitting Diodes Fabricated on β-Ga2O3 Substrate

KAUST Repository

Muhammed, Mufasila

2017-09-11

We demonstrate a state-of-the-art high-efficiency GaN-based vertical light-emitting diode (VLED) grown on a transparent and conductive (-201)-oriented (β-Ga2O3) substrate, obtained using a straightforward growth process that does not require a high cost lift-off technique or complex fabrication process. The high-resolution scanning transmission electron microscopy (STEM) images confirm that we produced high quality upper layers, including a multi-quantum well (MQW) grown on the masked β-Ga2O3 substrate. STEM imaging also shows a well-defined MQW without InN diffusion into the barrier. Electroluminescence (EL) measurements at room temperature indicate that we achieved a very high internal quantum efficiency (IQE) of 78%; at lower temperatures, IQE reaches ~ 86%. The photoluminescence (PL) and time-resolved PL analysis indicate that, at a high carrier injection density, the emission is dominated by radiative recombination with a negligible Auger effect; no quantum-confined Stark effect is observed. At low temperatures, no efficiency droop is observed at a high carrier injection density, indicating the superior VLED structure obtained without lift-off processing, which is cost-effective for large-scale devices.

High-Efficiency InGaN/GaN Quantum Well-Based Vertical Light-Emitting Diodes Fabricated on β-Ga2O3 Substrate.

Science.gov (United States)

Muhammed, Mufasila M; Alwadai, Norah; Lopatin, Sergei; Kuramata, Akito; Roqan, Iman S

2017-10-04

We demonstrate a state-of-the-art high-efficiency GaN-based vertical light-emitting diode (VLED) grown on a transparent and conductive (-201)-oriented (β-Ga 2 O 3 ) substrate, obtained using a straightforward growth process that does not require a high-cost lift-off technique or complex fabrication process. The high-resolution scanning transmission electron microscopy (STEM) images confirm that we produced high quality upper layers, including a multiquantum well (MQW) grown on the masked β-Ga 2 O 3 substrate. STEM imaging also shows a well-defined MQW without InN diffusion into the barrier. Electroluminescence (EL) measurements at room temperature indicate that we achieved a very high internal quantum efficiency (IQE) of 78%; at lower temperatures, IQE reaches ∼86%. The photoluminescence (PL) and time-resolved PL analysis indicate that, at a high carrier injection density, the emission is dominated by radiative recombination with a negligible Auger effect; no quantum-confined Stark effect is observed. At low temperatures, no efficiency droop is observed at a high carrier injection density, indicating the superior VLED structure obtained without lift-off processing, which is cost-effective for large-scale devices.

High-Efficiency InGaN/GaN Quantum Well-Based Vertical Light-Emitting Diodes Fabricated on β-Ga2O3 Substrate

KAUST Repository

Muhammed, Mufasila; Alwadai, Norah Mohammed Mosfer; Lopatin, Sergei; Kuramata, Akito; Roqan, Iman S.

2017-01-01

We demonstrate a state-of-the-art high-efficiency GaN-based vertical light-emitting diode (VLED) grown on a transparent and conductive (-201)-oriented (β-Ga2O3) substrate, obtained using a straightforward growth process that does not require a high cost lift-off technique or complex fabrication process. The high-resolution scanning transmission electron microscopy (STEM) images confirm that we produced high quality upper layers, including a multi-quantum well (MQW) grown on the masked β-Ga2O3 substrate. STEM imaging also shows a well-defined MQW without InN diffusion into the barrier. Electroluminescence (EL) measurements at room temperature indicate that we achieved a very high internal quantum efficiency (IQE) of 78%; at lower temperatures, IQE reaches ~ 86%. The photoluminescence (PL) and time-resolved PL analysis indicate that, at a high carrier injection density, the emission is dominated by radiative recombination with a negligible Auger effect; no quantum-confined Stark effect is observed. At low temperatures, no efficiency droop is observed at a high carrier injection density, indicating the superior VLED structure obtained without lift-off processing, which is cost-effective for large-scale devices.

Vertical axis wind turbines

Science.gov (United States)

Krivcov, Vladimir [Miass, RU; Krivospitski, Vladimir [Miass, RU; Maksimov, Vasili [Miass, RU; Halstead, Richard [Rohnert Park, CA; Grahov, Jurij [Miass, RU

2011-03-08

A vertical axis wind turbine is described. The wind turbine can include a top ring, a middle ring and a lower ring, wherein a plurality of vertical airfoils are disposed between the rings. For example, three vertical airfoils can be attached between the upper ring and the middle ring. In addition, three more vertical airfoils can be attached between the lower ring and the middle ring. When wind contacts the vertically arranged airfoils the rings begin to spin. By connecting the rings to a center pole which spins an alternator, electricity can be generated from wind.

Graphene and PbS quantum dot hybrid vertical phototransistor

Science.gov (United States)

Song, Xiaoxian; Zhang, Yating; Zhang, Haiting; Yu, Yu; Cao, Mingxuan; Che, Yongli; Dai, Haitao; Yang, Junbo; Ding, Xin; Yao, Jianquan

2017-04-01

A field-effect phototransistor based on a graphene and lead sulfide quantum dot (PbS QD) hybrid in which PbS QDs are embedded in a graphene matrix has been fabricated with a vertical architecture through a solution process. The n-type Si/SiO2 substrate (gate), Au/Ag nanowire transparent source electrode, active layer and Au drain electrode are vertically stacked in the device, which has a downscaled channel length of 250 nm. Photoinduced electrons in the PbS QDs leap into the conduction band and fill in the trap states, while the photoinduced holes left in the valence band transfer to the graphene and form the photocurrent under biases from which the photoconductive gain is evaluated. The graphene/QD-based vertical phototransistor shows a photoresponsivity of 2 × 103 A W-1, and specific detectivity up to 7 × 1012 Jones under 808 nm laser illumination with a light irradiance of 12 mW cm-2. The solution-processed vertical phototransistor provides a new facile method for optoelectronic device applications.

Vertical segregation among pathways mediating nitrogen loss (N2 and N2O production) across the oxygen gradient in a coastal upwelling ecosystem

Science.gov (United States)

Galán, Alexander; Thamdrup, Bo; Saldías, Gonzalo S.; Farías, Laura

2017-10-01

The upwelling system off central Chile (36.5° S) is seasonally subjected to oxygen (O2)-deficient waters, with a strong vertical gradient in O2 (from oxic to anoxic conditions) that spans a few metres (30-50 m interval) over the shelf. This condition inhibits and/or stimulates processes involved in nitrogen (N) removal (e.g. anammox, denitrification, and nitrification). During austral spring (September 2013) and summer (January 2014), the main pathways involved in N loss and its speciation, in the form of N2 and/or N2O, were studied using 15N-tracer incubations, inhibitor assays, and the natural abundance of nitrate isotopes along with hydrographic information. Incubations were developed using water retrieved from the oxycline (25 m depth) and bottom waters (85 m depth) over the continental shelf off Concepción, Chile. Results of 15N-labelled incubations revealed higher N removal activity during the austral summer, with denitrification as the dominant N2-producing pathway, which occurred together with anammox at all times. Interestingly, in both spring and summer maximum potential N removal rates were observed in the oxycline, where a greater availability of oxygen was observed (maximum O2 fluctuation between 270 and 40 µmol L-1) relative to the hypoxic bottom waters ( multiple N-cycling processes are modulating the isotopic nitrate composition over the shelf off central Chile during spring and summer. N removal processes in this coastal system appear to be related to the availability and distribution of oxygen and particles, which are a source of organic matter and the fuel for the production of other electron donors (i.e. ammonium) and acceptors (i.e. nitrate and nitrite) after its remineralization. These results highlight the links between several pathways involved in N loss. They also establish that different mechanisms supported by alternative N substrates are responsible for substantial accumulation of N2O, which are frequently observed as hotspots in the

N Reactor thermal plume characterization during Pu-only mode of operation

Energy Technology Data Exchange (ETDEWEB)

Ecker, R.M.; Thompson, F.L.; Whelan, G.

1983-04-01

Pacific Northwest Laboratories (PNL) performed field and modeling studies -from March 1982 through June 1983 to characterize the thermal plume from the N Reactor heated water outfall while the N Reactor operated in the Pu-only mode. Part 1 of this report deals with the field studies conducted to characterize the N Reactor thermal plume while in the Pu-only mode of operation. It includes a description of the study area, a description of field tasks and procedures, and data collection results and discussion. Part 2 describes the computer simulation of the thermal plume under different flow conditions and the calibration of the model used. It includes a description of the computer model and the assumptions on which it is based, a presentation of the input data used in this application, and a discussion of modeling results. Because the field studies were restricted by the NPOES permit variance to the spring months when high Columbia River flows prevail the mathematical modeling of the N Reactor thermal plume while the reactor operates in the Pu-only mode is instrumental in characterizing the plume during low Columbia River flows.

Cryogenic infrastructure for Fermilab's ILC vertical cavity test facility

Energy Technology Data Exchange (ETDEWEB)

Carcagno, R.; Ginsburg, C.; Huang, Y.; Norris, B.; Ozelis, J.; Peterson, T.; Poloubotko, V.; Rabehl, R.; Sylvester, C.; Wong, M.; /Fermilab

2006-06-01

Fermilab is building a Vertical Cavity Test Facility (VCTF) to provide for R&D and pre-production testing of bare 9-cell, 1.3-GHz superconducting RF (SRF) cavities for the International Linear Collider (ILC) program. This facility is located in the existing Industrial Building 1 (IB1) where the Magnet Test Facility (MTF) also resides. Helium and nitrogen cryogenics are shared between the VCTF and MTF including the existing 1500-W at 4.5-K helium refrigerator with vacuum pumping for super-fluid operation (125-W capacity at 2-K). The VCTF is being constructed in multiple phases. The first phase is scheduled for completion in mid 2007, and includes modifications to the IB1 cryogenic infrastructure to allow helium cooling to be directed to either the VCTF or MTF as scheduling demands require. At this stage, the VCTF consists of one Vertical Test Stand (VTS) cryostat for the testing of one cavity in a 2-K helium bath. Planning is underway to provide a total of three Vertical Test Stands at VCTF, each capable of accommodating two cavities. Cryogenic infrastructure improvements necessary to support these additional VCTF test stands include a dedicated ambient temperature vacuum pump, a new helium purification skid, and the addition of helium gas storage. This paper describes the system design and initial cryogenic operation results for the first VCTF phase, and outlines future cryogenic infrastructure upgrade plans for expanding to three Vertical Test Stands.

Diseño y construcción de un biodigestor anaeróbica vertical semicontinua para la obtención de gas metano y biol apartir de las cáscaras de naranja y mango.

OpenAIRE

Gonzabay Valdiviezo, Anthony William; Suárez Monroy, Pablo Moises

2016-01-01

En la elaboración del presente proyecto se pretende realizar el diseño y construcción de un biodigestor anaeróbico vertical semicontinuo para la obtención de gas metano y biol a partir de las cáscaras de naranja y mango. Esto se logrará al estimar los parámetros de diseño del Biodigestor anaeróbico, calculando la cantidad de gas metano y biol estimado que podría generar el biodigestor, además de construirlo y operarlo para la obtención de gas metano y biol. In the production of the presen...

Evaluación de la exactitud posicional vertical de una nube de puntos topográficos Lidar usando topografía convencional como referencia

Directory of Open Access Journals (Sweden)

Wilver Enrique Salinas Castillo

2013-11-01

Full Text Available La exactitud vertical de datos lidar es normalmente establecida por proveedores comerciales en un EMC máximo de 0.150 m. Sin embargo, los resultados de evaluaciones de exactitud en las que se han utilizado datos de campo por lo menos tres veces más exactos que los datos lidar, sugieren que dicha exactitud se observa solo cuando la densidad de los datos lidar es mayor a un punto sobre el terreno por metro cuadrado. Desafortunadamente, el número de estos estudios es limitado y se requiere de la elaboración de otras evaluaciones que confirmen dicha hipótesis. En este estudio se evaluó la exactitud vertical de una nube de puntos topográficos lidar de una densidad de 1.02 puntos sobre el terreno por metro cuadrado, usando como referencia datos recolectados en campo mediante una estación total. Los resultados coinciden con aquéllos de estudios previos, por lo que se sugiere establecer la EPV de la nube de puntos topográficos lidar en 0.200 m para terreno mixto y de cambios constantes y en 0.150 m para terreno con cambios topográficos gentiles. Sin embargo, la EPV no refleja la magnitud del 95% de los errores bajo la presencia de errores sistemáticos, por lo cual es necesario incluir el percentil 95 de los errores en la documentación de datos lidar

Diurnal and spatial (vertical dynamics of nutrients (N, P, Si in four sampling days (summer, fall, winter, and spring in a tropical shallow reservoir and their relationships with the phytoplankton community

Directory of Open Access Journals (Sweden)

J. J. Ramírez

Full Text Available The vertical and diurnal variation of nitrogen and phosphorus forms, as well as that of soluble reactive silica (SRS, were studied in four sampling days at Garças reservoir, a shallow tropical one located in the city of São Paulo, in southeastern Brazil. Except for N-NH4, all other inorganic forms of nitrogen (N-NO2, N-NO3, and total N demonstrated decreased concentrations toward the bottom of reservoir. Similarly, all showed significant diurnal differences on every sampling day, with increased values during the night due to absence of photosynthetic assimilation during that period. In the sampling days, these forms decreased on the spring sampling day due to the bloom of Microcystis registered during this period of the year. All three forms of phosphorus (SRP, particulate P, and total P showed significant vertical variation, except on the fall sampling day. On the summer sampling day there was an increase of both total P and particulate P, the latter because it constitutes more than 70% of the total P during all sampling days. Hourly phosphorus variation was significant during all sampling days, except for the summer one. The SRS vertical variation was significant during all sampling days, except for that in the spring. It was also different hourly on sampling days.

vertical bar Vub vertical bar from exclusive semileptonic B→π decays

International Nuclear Information System (INIS)

Flynn, Jonathan M.; Nieves, Juan

2007-01-01

We use Omnes representations of the form factors f + and f 0 for exclusive semileptonic B→π decays, paying special attention to the treatment of the B* pole and its effect on f + . We apply them to combine experimental partial branching fraction information with theoretical calculations of both form factors to extract vertical bar V ub vertical bar. The precision we achieve is competitive with the inclusive determination and we do not find a significant discrepancy between our result, vertical bar V ub vertical bar=(3.90+/-0.32+/-0.18)x10 -3 , and the inclusive world average value (4.45+/-0.20+/-0.26)x10 -3 [Heavy Flavor Averaging Group (HFAG), hep-ex/0603003

Efecto del entrenamiento combinado de pliometría y electroestimulación en salto vertical. (Effect of combined plyometric and electrostimulation training on vertical jump.

Directory of Open Access Journals (Sweden)

Elisa Benito Martínez

2010-10-01

Full Text Available Resumen En este estudio se han analizado los efectos del entrenamiento combinado de pliometría y electroestimulación en un entrenamiento de fuerza muscular de los miembros inferiores. El estudio incluyó tres grupos experimentales, que trabajaron ambos métodos en orden diferente y de forma simultánea, y uno de control. Participaron 78 atletas, 40 mujeres y 38 hombres, de disciplinas de velocidad (100 y 200 m lisos y 100 y 110 m vallas, con una edad de 17,94 ± 1,44 años y una masa de 58,53 ± 8,05 kg. El programa incluyó dos días / sem de entrenamiento pliométrico y dos sesiones utilizando un electroestimulador Megasonic 313-P4. Tras dos meses de entrenamiento, se midió con plataforma de contacto ORGANISER PSION 2 la altura de salto vertical y potencia del tren inferior en test de Abalakov y Drop Jump. Las mayores diferencias pre/post test (p Abstract This paper analyses the effects of combined electrostimulation and plyometric training on lower body strength training. The training programme was applied to three experimental groups and one control group. The experimental groups used both methods simultaneously but in different order. The participants were 78 sprinters (100m and 200m, and 100m and 110m hurdles, 38 male and 40 female. Their average age was 15,9 ± 1,4 years and their average weight was 58,53 ± 8,05kg. The training programme consisted in two days a week of plyometric training and two sessions with a Megasonic 313-P4 electrostimulation unit. After two months training, vertical jump height and lower body power were measured in Abalakov test and Drop Jump test with PSION ORGANISER II. The most significant pre- and post-test (p

A preliminary comparison between TOVS and GOME level 2 ozone data

Science.gov (United States)

Rathman, William; Monks, Paul S.; Llewellyn-Jones, David; Burrows, John P.

1997-09-01

A preliminary comparison between total column ozone concentration values derived from TIROS Operational Vertical Sounder (TOVS) and Global Ozone Monitoring Experiment (GOME) has been carried out. Two comparisons of ozone datasets have been made: a) TOVS ozone analysis maps vs. GOME level 2 data; b) TOVS data located at Northern Hemisphere Ground Ozone Stations (NHGOS) vs. GOME data. Both analyses consistently showed an offset in the value of the total column ozone between the datasets [for analyses a) 35 Dobson Units (DU); and for analyses b) 10 DU], despite a good correlation between the spatial and temporal features of the datasets. A noticeably poor correlation in the latitudinal bands 10°/20° North and 10°/20° South was observed—the reasons for which are discussed. The smallest region which was statistically representative of the ozone value correlation dataset of TOVS data at NHGOS and GOME level-2 data was determined to be a region that was enclosed by effective radius of 0.75 arc-degrees (83.5km).

Time changes of vertical profile of neutron fluence rate in LVR-15 reactor

International Nuclear Information System (INIS)

Viererbl, L.; Stehno, J.; Erben, O.; Lahodova, Z.; Marek, M.

2003-01-01

The LVR-15 reactor is a light water research type reactor, which is situated, in Nuclear Research Institute, Rez near Prague. The reactor is used as a multipurpose facility. For some experiments and material productions, e.g. for homogeneity of silicon resistance in production of radiation doped silicon, the time changes of vertical profile of neutron fluence rate are particularly important. The assembly used for silicon irradiation has two self-powered neutron detectors installed in a vertical irradiation channel in LVR-15 reactor. Vertical profile of thermal neutron fluence rate was automatically scanned during reactor operation. The results of measurements made in 2002 and 2003 with these detectors are presented. A set of vertical profile measurements was made during two 21-days reactor cycles. During the cycle the vertical profile slightly changes both in the position of its maximum and in the shape. The time dependences of the position of profile maximum and the profile width at half maximum during the cycle are given. (author)

Operations on N-varieties of regular ω-languages and products on regular ω-languages

International Nuclear Information System (INIS)

Phan Trung Huy; Do Long Van

1995-12-01

In an earlier paper (1986) we have shown the existence of an Eilenberg correspondence between varieties of regular ω-languages (N-varieties, for short) and varieties of finite monoids (M-varieties) not being a variety of groups. The aim of this paper is to establish the correspondence in the connection with some operations on languages and on M-varieties. For this, some operations on N-varieties concerning with the shuffle product on ω-languages are studied, explicit forms of some N-varieties closed under shuffle product are given. In particular, a new product on ω-language and a new operation on N-varieties are introduced and considered. (author). 17 refs

Small Vertical Axis Wind Turbines: aerodynamics and starting behavior

Directory of Open Access Journals (Sweden)

Horia DUMITRESCU

2013-12-01

Full Text Available In urban areas the wind is very turbulent and unstable with fast changes in direction andvelocity. In these environments, the use of small vertical axis wind turbines (VAWT becomesincreasingly attractive due to several advantages over horizontal axis wind turbines (HAWT.However, such designs have received much less attention than the more common propeller-typedesigns and the understanding of same aspects of their operation remains, to this day, incomplete.This is particularly true of their starting characteristics. Indeed, same authors heuristically maintainthat they cannot start without external assistance. This paper reviews the cause of the inability of thelow solidity fixed pitch vertical axis wind turbines to self-start, and investigates the way ofovercoming this draw back.

Film behaviour of vertical gas-liquid flow in a large diameter pipe

OpenAIRE

Zangana, Mohammed Haseeb Sedeeq

2011-01-01

Gas-liquid flow commonly occurs in oil and gas production and processing system. Large diameter vertical pipes can reduce pressure drops and so minimize operating costs. However, there is a need for research on two-phase flow in large diameter pipes to provide confidence to designers of equipments such as deep water risers. In this study a number of experimental campaigns were carried out to measure pressure drop, liquid film thickness and wall shear in 127mm vertical pipe. Total pressur...

El gimnasio de la universidad de Princeton – (EE. UU.

Directory of Open Access Journals (Sweden)

Walter O. Cain, Arquitectos y asociados

1973-07-01

Full Text Available The building is made up of two levels, to hold 10,000 people. The top floor houses: athletics track, four tennis courts, basketball, hand-ball, volley-ball and badminton. The ground floor includes the throwing area, shooting, squash, wrestling, fencing, and the betweenfloor with offices and machine rooms. The metal roof structure is characteristic and extremely interesting; it comprises three parts: a conically shaped half dome, and two intermediate support triangular shapes, which also acto to give daylight to the great hall, which is free from vertical supports.El edificio se compone de dos plantas, con capacidad para 10.000 personas. La planta alta alberga: la pista de atletismo, cuatro pistas de tenis, baloncesto, balonmano, balón volea y badminton. La baja comprende la zona de lanzamientos, tiro, squash, lucha, esgrima, entreplanta de oficinas y cuartos de máquinas. Es característica y sumamente interesante la estructura metálica de ía cubierta, que se compone de tres partes: semicúpula, cónica y alabeada, con 2 formas trianguladas intermedias de soporte, que sirven también para proporcionar luz natural a la gran nave libre de pilares.

Vertical components of surface vibrations induced by mining tremors in the Upper Silesian Coalfield, Poland

International Nuclear Information System (INIS)

Maciag, E.; Kowalski, W.

1997-01-01

Characteristics of vertical components of surface vibration is epicentral zones due to mining tremors in the Upper Silesian Coalfield (USC) are analysed. Both maximum acceleration amplitudes and dominant frequencies of vertical (Z) and horizontal (N-S and E-W) components of vibrations are compared. The role played by the vertical components of vibrations in estimates of hazard for surface structures excited by mining tremors is discussed. 8 refs., 7 figs

Continuous-wave optically pumped green perovskite vertical-cavity surface-emitter

KAUST Repository

Alias, Mohd Sharizal; Liu, Zhixiong; Alatawi, Abdullah; Ng, Tien Khee; Wu, Tao; Ooi, Boon S.

2017-01-01

We report an optically pumped green perovskite vertical-cavity surface-emitter operating in continuous-wave (CW) with a power density threshold of ~89 kW/cm2. The device has an active region of CH3NH3PbBr3 embedded in a dielectric microcavity

The theory of pseudo-differential operators on the noncommutative n-torus

Science.gov (United States)

Tao, J.

2018-02-01

The methods of spectral geometry are useful for investigating the metric aspects of noncommutative geometry and in these contexts require extensive use of pseudo-differential operators. In a foundational paper, Connes showed that, by direct analogy with the theory of pseudo-differential operators on finite-dimensional real vector spaces, one may derive a similar pseudo-differential calculus on noncommutative n-tori, and with the development of this calculus came many results concerning the local differential geometry of noncommutative tori for n=2,4, as shown in the groundbreaking paper in which the Gauss-Bonnet theorem on the noncommutative two-torus is proved and later papers. Certain details of the proofs in the original derivation of the calculus were omitted, such as the evaluation of oscillatory integrals, so we make it the objective of this paper to fill in all the details. After reproving in more detail the formula for the symbol of the adjoint of a pseudo-differential operator and the formula for the symbol of a product of two pseudo-differential operators, we extend these results to finitely generated projective right modules over the noncommutative n-torus. Then we define the corresponding analog of Sobolev spaces and prove equivalents of the Sobolev and Rellich lemmas.

Effects of asymmetric vertical disruptions on ITER components

International Nuclear Information System (INIS)

Albanese, R.; Carpentieri, B.; Cavinato, M.; Minucci, S.; Palmaccio, R.; Portone, A.; Rubinacci, G.; Testoni, P.; Ventre, S.; Villone, F.

2015-01-01

Highlights: • Halo current analysis of AVDEs (asymmetric VDEs) is performed. • Both resistive and inductive effects are considered. • Suitable compression techniques and supercomputing resources are used. • The vertical force on the sectors is nearly uniform. • The radial loads on the various sectors are very different. - Abstract: This paper deals with the halo current distribution due to asymmetric vertical displacement events (VDEs) and the subsequent force distributions on the conducting structures in the ITER tokamak. Both the eddy and halo current analyses have been carried out using the 3D code CARIDDI, based on an integral formulation in the conducting region. The plasma plays the role of a source term. The axisymmetric time evolution of the plasma is taken by 2D axisymmetric simulations. The most critical case is a slow VDE downward combined with an n = 1 kink, which may yield large horizontal forces and peaking factors. A simplified n = 1, m = 1 kink model is taken, given by a rigid horizontal displacement accompanied by a tilt. The halo currents are treated as injected currents on the faces of the first wall hit by the plasma. To take into account the inductive effects, which are important especially in the transient phases, suitable compression techniques and supercomputing resources have been utilized. In the worst case the total vertical force on the structure due to the halo currents is about 90 MN downwards (about 30 of which on the divertor); the horizontal force is about 4 MN (about half of which on the divertor); the distribution of the vertical force on the sectors is nearly uniform, whereas the radial loads on the various sectors are very different from each other

Effects of asymmetric vertical disruptions on ITER components

Energy Technology Data Exchange (ETDEWEB)

Albanese, R. [Associazione EURATOM/ENEA/CREATE, DIETI, Università di Napoli Federico II, Napoli (Italy); Carpentieri, B. [Johann Bernoulli Institute for Mathematics and Computer Science, University of Groningen, Groningen (Netherlands); Cavinato, M. [Fusion for Energy, Torres Diagonal Litoral B3, c/ Josep Plá n.2, Barcelona (Spain); Minucci, S. [Associazione EURATOM/ENEA/CREATE, DIETI, Università di Napoli Federico II, Napoli (Italy); Palmaccio, R. [Associazione EURATOM/ENEA/CREATE, DIEI, Università di Cassino e del Lazio Meridionale, Cassino, FR (Italy); Portone, A. [Fusion for Energy, Torres Diagonal Litoral B3, c/ Josep Plá n.2, Barcelona (Spain); Rubinacci, G. [Associazione EURATOM/ENEA/CREATE, DIETI, Università di Napoli Federico II, Napoli (Italy); Testoni, P., E-mail: pietro.testoni@f4e.europa.eu [Fusion for Energy, Torres Diagonal Litoral B3, c/ Josep Plá n.2, Barcelona (Spain); Ventre, S.; Villone, F. [Associazione EURATOM/ENEA/CREATE, DIEI, Università di Cassino e del Lazio Meridionale, Cassino, FR (Italy)

2015-05-15

Highlights: • Halo current analysis of AVDEs (asymmetric VDEs) is performed. • Both resistive and inductive effects are considered. • Suitable compression techniques and supercomputing resources are used. • The vertical force on the sectors is nearly uniform. • The radial loads on the various sectors are very different. - Abstract: This paper deals with the halo current distribution due to asymmetric vertical displacement events (VDEs) and the subsequent force distributions on the conducting structures in the ITER tokamak. Both the eddy and halo current analyses have been carried out using the 3D code CARIDDI, based on an integral formulation in the conducting region. The plasma plays the role of a source term. The axisymmetric time evolution of the plasma is taken by 2D axisymmetric simulations. The most critical case is a slow VDE downward combined with an n = 1 kink, which may yield large horizontal forces and peaking factors. A simplified n = 1, m = 1 kink model is taken, given by a rigid horizontal displacement accompanied by a tilt. The halo currents are treated as injected currents on the faces of the first wall hit by the plasma. To take into account the inductive effects, which are important especially in the transient phases, suitable compression techniques and supercomputing resources have been utilized. In the worst case the total vertical force on the structure due to the halo currents is about 90 MN downwards (about 30 of which on the divertor); the horizontal force is about 4 MN (about half of which on the divertor); the distribution of the vertical force on the sectors is nearly uniform, whereas the radial loads on the various sectors are very different from each other.

Shrub type dominates the vertical distribution of leaf C : N : P stoichiometry across an extensive altitudinal gradient

Science.gov (United States)

Zhao, Wenqiang; Reich, Peter B.; Yu, Qiannan; Zhao, Ning; Yin, Chunying; Zhao, Chunzhang; Li, Dandan; Hu, Jun; Li, Ting; Yin, Huajun; Liu, Qing

2018-04-01

Understanding leaf stoichiometric patterns is crucial for improving predictions of plant responses to environmental changes. Leaf stoichiometry of terrestrial ecosystems has been widely investigated along latitudinal and longitudinal gradients. However, very little is known about the vertical distribution of leaf C : N : P and the relative effects of environmental parameters, especially for shrubs. Here, we analyzed the shrub leaf C, N and P patterns in 125 mountainous sites over an extensive altitudinal gradient (523-4685 m) on the Tibetan Plateau. Results showed that the shrub leaf C and C : N were 7.3-47.5 % higher than those of other regional and global flora, whereas the leaf N and N : P were 10.2-75.8 % lower. Leaf C increased with rising altitude and decreasing temperature, supporting the physiological acclimation mechanism that high leaf C (e.g., alpine or evergreen shrub) could balance the cell osmotic pressure and resist freezing. The largest leaf N and high leaf P occurred in valley region (altitude 1500 m), likely due to the large nutrient leaching from higher elevations, faster litter decomposition and nutrient resorption ability of deciduous broadleaf shrub. Leaf N : P ratio further indicated increasing N limitation at higher altitudes. Interestingly, drought severity was the only climatic factor positively correlated with leaf N and P, which was more appropriate for evaluating the impact of water status than precipitation. Among the shrub ecosystem and functional types (alpine, subalpine, montane, valley, evergreen, deciduous, broadleaf, and conifer), their leaf element contents and responses to environments were remarkably different. Shrub type was the largest contributor to the total variations in leaf stoichiometry, while climate indirectly affected the leaf C : N : P via its interactive effects on shrub type or soil. Collectively, the large heterogeneity in shrub type was the most important factor explaining the overall leaf C : N : P variations

Asociación de la abundancia y la distribución vertical de atunes y peces de pico en el sureste del Mar Caribe

Directory of Open Access Journals (Sweden)

Nora Eslava

2003-03-01

Full Text Available Se estimó la profundidad de suspensión de los anzuelos del palangre usando el método de Imitación Mecánica de los Sistemas Flexibles, mientras que la distribución vertical de atunes y peces de pico se determinó mediante el índice de abundancia relativa obtenido de capturas de barcos palangreros (11 a 25 m de eslora del puerto de Cumaná, Venezuela y que operan en el Mar Caribe a una profundidad de 65 a 142 m. Se evaluó la CPUE por especie de acuerdo a la profundidad, encontrándose valores altos en la mayoría de los individuos de las especies capturadas en el estrato de 105 a 125 m. El atún aleta amarilla (Thunnus albacares fue el que presentó los más altos rendimientos (3.37 peces/100 anzuelos, mientras que la aguja azul (Makaira nigricans los más bajos (0.04 peces/100 anzuelos. La comparación estadística no permitió rechazar la hipótesis de ausencia del efecto de profundidad (Kruskal-Wallis p > .05, y se puso en evidencia una distribución homogénea, en la columna de agua, del atún aleta amarilla (Thunnus albacares, albacora (Thunnus alalung a, ojo gordo (Thunnus obesus, pez vela (Istiophorus albican s, aguja blanca (Tetrapturus albidus y aguja azul (Makaira nigrican s. Se concluye que la concentración de la pesca en el margen sur del Mar Caribe, posiblemente, es debido a varios factores hidroclimáticos tales como la temperatura del agua y la concentración de oxígeno disuelto que influyen sobre la captura de los atunes y peces de pico delimitando su distribución con res-pecto a la profundidad.The longline hooks suspension depth was estimated using the Mechanic Imitation of Flexible Systems method. The vertical distribution of tunas and billfish was determined by the relative abundance index, obtained from the catch by 11 to 25 m -long longline vessels, -based at Cumaná, Venezuela, South-eastern Caribbean Sea in depths of 65 to 142 m. The CPUE was evaluated per species, according to depth. High values were found for

A 3D Vertically Integrated Deep N-Well CMOS MAPS for the SuperB Layer0

International Nuclear Information System (INIS)

Traversi, G; Manghisoni, M; Re, V; Gaioni, L; Ratti, L

2011-01-01

Deep N-Well (DNW) Monolithic Active Pixel Sensors (MAPS) have been developed in the last few years with the aim of building monolithic sensors with similar functionalities as hybrid pixels systems. In these devices the triple well option, available in deep submicron processes, is exploited to implement analog and digital signal processing at the pixel level. Many prototypes have been fabricated in a planar (2D) 130nm CMOS technology. A new kind of DNW-MAPS, namely Apsel5 3 D, which exploits the capabilities of vertical integration (3D) processes, is presented and discussed in this paper. The impact of 3D processes on the design and performance of DNW pixel sensors could be large, with significant advantages in terms of detection efficiency, pixel cell size and immunity to cross-talk, therefore complying with the severe constraints set by future HEP experiments.

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

International Nuclear Information System (INIS)

COMPTON, J.A.

1999-01-01

A vertical calciner will be used to demonstrate the direct denitration process for converting plutonium-bearing liquors to stable plutonium rich solids. The calciner and some of its associated equipment were previously tested with non-radioactive chemicals to demonstrate operability

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

Energy Technology Data Exchange (ETDEWEB)

COMPTON, J.A.

1999-10-05

A vertical calciner will be used to demonstrate the direct denitration process for converting plutonium-bearing liquors to stable plutonium rich solids. The calciner and some of its associated equipment were previously tested with non-radioactive chemicals to demonstrate operability.

Escrita Escolar Brasileira: a escrita vertical

Directory of Open Access Journals (Sweden)

Carlos André Xavier Villela

2014-12-01

Full Text Available O exame grafoscópico visa essencialmente a determinar se duas escritas partiram ou não de um mesmo punho. A fim de buscar dados empíricos capazes de melhor embasar uma valoração de raridade, diversos pesquisadores se dedicaram ao estudo dos sistemas de escrita. O presente trabalho analisa algumas bibliografias nacionais e estrangeiras que descrevem como se deu o alvorecer da escrita vertical e sua implantação no universo escolar brasileiro. Foi a partir das últimas décadas do século XIX que alógrafos cursivos verticais começaram a ser utilizados para o ensino da escrita. Os novos sistemas, sob a denominação escrita vertical, tiveram presença marcante em todo o mundo ocidental, sendo até hoje os sistemas predominantes em diversos países.

Vertical-axis turbine/propeller for ship propulsion

Energy Technology Data Exchange (ETDEWEB)

Barkla, H.M.

1984-01-01

There are so many variables in the design and operating conditions of a vertical-axis turbine/propeller for the propulsion of a ship by wind that a preliminary study is offered, based on two simplified models. Study of a linear motion of blades in air and water shows optimum conditions for blade-speed and blade-incidence. Analysis of the second, cyclical model is simplified by the assumption of constant angles of incidence. While the logical superiority of the vertical-axis system, with its low transmission loss, may not alone give it the advantage over all other systems in upwind and downwind sailing, there are indications that in the beam wind it is in a class of its own; the Voith-Schneider-Type propeller then produces a thrust with a major component to windward, so that the combined unit leaves little or no athwartships force.

Operating experience with superconducting cavities at the TESLA test facility

International Nuclear Information System (INIS)

Moeller, Wolf-Dietrich

2003-01-01

A description of the TESLA Test Facility, which has been set up at DESY by the TeV Energy Superconducting Accelerator (TESLA) collaboration, will be given as it is now after five years of installation and operation. The experience with the first three modules, each containing 8 superconducting 9-cell cavities, installed and operated in the TTF-linac will be described. The measurements in the vertical and horizontal cryostats as well as in the modules will be compared. Recent results of the operation at the TESLA design current, macropulses of 800 μsec with bunches of 3.2 nC at a rate of 2.25 MHz are given. New measurement results of the higher order modes (HOM) will be presented. The operation and optimisation of the TTF Free Electron Laser (TTF-FEL) will also be covered in this paper. (author)

Skeletal anteroposterior discrepancy and vertical type effects on lower incisor preoperative decompensation and postoperative compensation in skeletal Class III patients.

Science.gov (United States)

Ahn, Hyo-Won; Baek, Seung-Hak

2011-01-01

To determine the initial compensation, preoperative decompensation, and postoperative compensation of the lower incisors according to the skeletal anteroposterior discrepancy and vertical type in skeletal Class III patients. The samples consisted of 68 skeletal Class III patients treated with two-jaw surgery and orthodontic treatment. Lateral cephalograms were taken before preoperative orthodontic treatment (T0) and before surgery (T1) and after debonding (T2). According to skeletal anteroposterior discrepancy/vertical type (ANB, criteria  =  -4°; SN-GoMe, criteria  =  35°) at the T0 stage, the samples were allocated into group 1 (severe anteroposterior discrepancy/hypodivergent vertical type, N  =  17), group 2 (moderate anteroposterior discrepancy/hypodivergent vertical type, N  =  17), group 3 (severe anteroposterior discrepancy/hyperdivergent vertical type, N  =  17), or group 4 (moderate anteroposterior discrepancy/hyperdivergent vertical type, N  =  17). After measurement of variables, one-way analysis of variance with Duncan's multiple comparison test, crosstab analysis, and Pearson correlation analysis were performed. At T0, groups 3 and 2 exhibited the most and least compensated lower incisors. In group 2, good preoperative decompensation and considerable postoperative compensation resulted in different values for T0, T1, and T2 (IMPA, T0 lower incisors in Class III patients.

The influence of plasma-surface interaction on the performance of tungsten at the ITER divertor vertical targets

Science.gov (United States)

De Temmerman, G.; Hirai, T.; Pitts, R. A.

2018-04-01

The tungsten (W) material in the high heat flux regions of the ITER divertor will be exposed to high fluxes of low-energy particles (e.g. H, D, T, He, Ne and/or N). Combined with long-pulse operations, this implies fluences well in excess of the highest values reached in today’s tokamak experiments. Shaping of the individual monoblock top surface and tilting of the vertical targets for leading-edge protection lead to an increased surface heat flux, and thus increased surface temperature and a reduced margin to remain below the temperature at which recrystallization and grain growth begin. Significant morphology changes are known to occur on W after exposure to high fluences of low-energy particles, be it H or He. An analysis of the formation conditions of these morphology changes is made in relation to the conditions expected at the vertical targets during different phases of operations. It is concluded that both H and He-related effects can occur in ITER. In particular, the case of He-induced nanostructure (also known as ‘fuzz’) is reviewed. Fuzz formation appears possible over a limited region of the outer vertical target, the inner target being generally a net Be deposition area. A simple analysis of the fuzz growth rate including the effect of edge-localized modes (ELMs) and the reduced thermal conductivity of fuzz shows that the fuzz thickness is likely to be limited by the occurrence of annealing during ELM-induced thermal excursions. Not only the morphology, but the material mechanical and thermal properties can be modified by plasma exposure. A review of the existing literature is made, but the existing data are insufficient to conclude quantitatively on the importance and extent of these effects for ITER. As a consequence of the high surface temperatures in ITER, W recrystallization is an important effect to consider, since it leads to a decrease in material strength. An approach is proposed here to develop an operational budget for the W material, i

New Technical Solution for Vertical Shaft Equipping Using Steel Headframe of Multifunction Purpose

Science.gov (United States)

Kassikhina, Elena; Pershin, Vladimir; Glazkov, Yurij

2017-11-01

The article reviews a novel approach to the design of steel angle headframe for vertical shafts of coal and ore mines on the basis of rational design solutions. Practice of construction of coal and ore mines provides application of various designs for steel angle headframes which are divided into separate large assembly blocks and constructive elements during assembling operations. Design of these blocks and elements, their weight and dimensions effect the chose of the method of assembling on which economic and technological indicators, as well as duration of down-time, depend on during performance of construction operations in shaft. The technical solution on equipment provision for mine vertical shaft using headframe of multifunctional purpose will allow changing the management construction of vertical shaft. The constructive design of the headgear allows application of the effective method of assembly and thus to provide improvement of the technical and economic indexes, and high calendar time rate of the shaft construction due to reduction of duration of works on equipment provision for the shaft and to refurbishment of the shaft in order to carry out horizontal mining.

Seabrook, N.H. Wastewater Treatment Plant Chief Operator Recognized for Outstanding Service

Science.gov (United States)

Dustin Price, a resident of Berwick Maine and the Chief Operator of the Seabrook, N.H. Wastewater Treatment Plant, was honored by EPA with a 2016 Regional Wastewater Treatment Plant Operator of the Year Excellence Award.

Coupling the Mars Dust and Water Cycles: Investigating the Role of Clouds in Controlling the Vertical Distribution of Dust During N. H. Summer

Science.gov (United States)

Kahre, M. A.; Haberle, R. M.; Hollingsworth, J. L.; Wilson, R. J.

2014-01-01

The dust cycle is critically important for the current climate of Mars. The radiative effects of dust impact the thermal and dynamical state of the atmosphere (Gierasch and Goody, 1968; Haberle et al., 1982; Zurek et al., 1992). Although dust is present in the Martian atmosphere throughout the year, the level of dustiness varies with season. The atmosphere is generally the dustiest during northern fall and winter and the least dusty during northern spring and summer (Smith, 2004). Dust particles are lifted into the atmosphere by dust storms that range in size from meters to thousands of kilometers across (Cantor et al., 2001). During some years, regional storms combine to produce hemispheric or planet encircling dust clouds that obscure the surface and raise atmospheric temperatures by as much as 40 K (Smith et al., 2002). Key recent observations of the vertical distribution of dust indicate that elevated layers of dust exist in the tropics and sub-tropics throughout much of the year (Heavens et al., 2011). These observations have brought particular focus on the processes that control the vertical distribution of dust in the Martian atmosphere. The goal of this work is to further our understanding of how clouds in particular control the vertical distribution of dust, particularly during N. H. spring and summer

Formation of a vertical MOSFET for charge sensing in a Si micro-fluidic channel

International Nuclear Information System (INIS)

Lyu, Hong-Kun; Kim, Dong-Sun; Shin, Jang-Kyoo; Choi, Pyung; Lee, Jong-Hyun; Park, Hey-Jung; Park, Chin-Sung; Lim, Geun-Bae

2004-01-01

We have formed a fluidic channel that can be used in micro-fluidic systems and fabricated a 3-dimensional vertical metal-oxide semiconductor field-effect transistor (vertical MOSFET) in the convex corner of a Si micro-fluidic channel by using an anisotropic tetramethyl ammonium hydroxide (TMAH) etching solution. A Au/Cr layer was used for the gate metal and might be useful for detecting charged biomolecules. The electrical characteristics of the vertical MOSFET and its operation as a chemical sensor were investigated. At V DS = -5 V and V GS = -5 V the drain current of the device was -22.5 μA and the threshold voltage was about -1.4 V. A non-planar, non-rectangular vertical MOSFET with a trapezoidal gate was transformed into an equivalent rectangularly based one by using a Schwartz-Christoffel transformation. The LEVEL1 device parameters of the vertical MOSFET were extracted from the measured electrical device characteristics and were used in the SPICE simulation for the vertical MOSFET. The measured and the simulated results for the vertical PMOSFET showed relatively good agreement. When the vertical MOSFET was dipped into a thiol DNA solution, the drain current decreased due to charged biomolecules probably being adsorbed on the gate, which indicates that a vertical MOSFET in a Si micro-fluidic channel might be useful for sensing charged biomolecules.

Flexibility Considerations on the Hydrodynamic Loading on a Vertical Wedge Drop

Science.gov (United States)

Ren, Zhongshu; Wang, Zhaoyuan; Judge, Carolyn; Stern, Fred; Ikeda, Christine

2017-11-01

High-speed craft operating at in waves frequently become airborne and slam into the water surface. This fluid-structure interaction problem is important to understand in order to increase the operating envelope of these craft. The goals of the current work are to investigate both the hydrodynamic loads and the resulting structural response on a planing hull. A V-shaped wedge is dropped vertically into calm water. The hydrodynamic pressure is measured using pressure sensors at discrete points on the hull. Two hulls are studied: one is rigid and one is flexible. Predictions of the hydrodynamic loading are made using Wagner's theory, Vorus's theory, and simulations in CFDShip Iowa. These predictions assume the structure is completely rigid. These predictions of the pressure coefficient match well with the rigid hull, as expected. The spray root is tracked in the rigid experimental set and compared with the theoretical and computational models. The pressure coefficient measured on the flexible hull shows discrepancies with the predictions due to the fluid-structure interaction. These discrepancies are quantified and interpreted in light of the structural flexibility. Funding for this work is from the Office of Naval Research Grant Number N00014-16-1-3188.

Vertical circulation and thermospheric composition: a modelling study

Directory of Open Access Journals (Sweden)

H. Rishbeth

1999-06-01

Full Text Available The coupled thermosphere-ionosphere-plasmasphere model CTIP is used to study the global three-dimensional circulation and its effect on neutral composition in the midlatitude F-layer. At equinox, the vertical air motion is basically up by day, down by night, and the atomic oxygen/molecular nitrogen [O/N2] concentration ratio is symmetrical about the equator. At solstice there is a summer-to-winter flow of air, with downwelling at subauroral latitudes in winter that produces regions of large [O/N2] ratio. Because the thermospheric circulation is influenced by the high-latitude energy inputs, which are related to the geometry of the Earth's magnetic field, the latitude of the downwelling regions varies with longitude. The downwelling regions give rise to large F2-layer electron densities when they are sunlit, but not when they are in darkness, with implications for the distribution of seasonal and semiannual variations of the F2-layer. It is also found that the vertical distributions of O and N2 may depart appreciably from diffusive equilibrium at heights up to about 160 km, especially in the summer hemisphere where there is strong upwelling. Atmospheric composition and structure (thermosphere · composition and chemistry · Ionosphere (ionosphere · atmosphere interactions

Wide-band operation of quasi-optical distributed superconductor/insulator/superconductor mixers with epitaxial NbN/AlN/NbN junctions

International Nuclear Information System (INIS)

Kohjiro, S; Shitov, S V; Wang, Z; Uzawa, Y; Miki, S; Kawakami, A; Shoji, A

2004-01-01

For the optimum design of integrated receivers operating above the gap frequency of Nb, we have designed, fabricated and tested NbN-based quasi-optical superconductor/insulator/superconductor (SIS) mixers. The mixer chip incorporates a resonant half-wavelength epitaxial NbN/AlN/NbN junction, a twin-slot antenna and their coupling circuits. We adopted two kinds of coupling circuit between the antenna and the SIS junction: one is an in-phase feed with a length of 95 μm and the other is an anti-phase feed of 30 μm length. It was found that the anti-phase mixer reveals a 3 dB bandwidth of 43% of the centre frequency; the uncorrected double-sideband receiver noise temperature T RX = 691 K at 0.91 THz and T RX = 844 K at 0.80 THz, while 17% and T RX = 1250 K at 0.79 THz for the in-phase version. Possible reasons for this difference are discussed, which could be transmission loss and its robustness with respect to the variation of junction parameters. These experimental results suggest the NbN-based distributed mixer with the anti-phase feed is a better candidate for wide-band integrated receivers operating above 0.7 THz

Market size and vertical structure in the rail way industry

OpenAIRE

Matsushima, Noriaki; Mizutani, Fumitoshi

2011-01-01

We provide a theoretical framework to discuss the relation between market size and vertical structure in the railway industry. The framework is based on a simple downstream monopoly model with two input suppliers, labor forces and the rail infrastructure firm. The operation of the downstream firm (i.e., the train operating firm) generates costs on the rail infrastructure firm. We show that the downstream firm with a larger market size is more likely to integrate with the rail infrastructure f...

Vertical propagation characteristics and seasonal variability of tidal wind oscillations in the MLT region over Trivandrum (8.5° N, 77° E: first results from SKiYMET Meteor Radar

Directory of Open Access Journals (Sweden)

M. N. Sasi

2006-11-01

Full Text Available Tidal activity in the Mesospheric Lower Thermosphere (MLT region over Trivandrum (8.5° N, 77° E is investigated using the observations from newly installed SKiYMET Meteor Radar. The seasonal variability and vertical propagation characteristics of atmospheric tides in the MLT region are addressed in the present communication. The observations revealed that the diurnal tide is more prominent than the semi/terdiurnal components over this latitude. It is also observed that the amplitudes of meridional components are stronger than that of zonal ones. The amplitude and phase structure shows the vertical propagation of diurnal tides with vertical wavelength of ~25 km. However, the vertical wavelength of the semidiurnal tide showed considerable variations. The vertical propagation characteristics of the terdiurnal tide showed some indications of their generating mechanisms. The observed features of tidal components are compared with Global Scale Wave Model (GSWM02 values and they showed a similar amplitude and phase structure for diurnal tides. Month-to-month variations in the tidal amplitudes have shown significant seasonal variation. The observed seasonal variation is discussed in light of the variation in tidal forcing and dissipation.

AdS5/CFT4 four-point functions of chiral primary operators: Cubic vertices

International Nuclear Information System (INIS)

Lee, Sangmin

1999-01-01

We study the exchange diagrams in the computation of four-point functions of all chiral primary operators in D=4, N=4 super Yang-Mills using AdS/CFT correspondence. We identify all supergravity fields that can be exchanged and compute the cubic couplings. As a byproduct, we also rederive the normalization of the quadratic action of the exchanged fields. The cubic couplings computed in this paper and the propagators studied extensively in the literature can be used to compute almost all the exchange diagrams explicitly. Some issues in computing the complete four-point function in the 'massless sector' are discussed

Treinamento de força com uso de correntes e potencialização pós-ativação do salto vertical Entrenamiento de fuerza con cadenas y la potenciación post-activación del salto vertical Chain resistance training and vertical jump post-activation potentiation

Directory of Open Access Journals (Sweden)

Jéderson Nunes

2012-12-01

Full Text Available A Potencialização Pós-Ativação (PPA é estratégia para melhora do desempenho com uso de carga fixa (RF, definida no ponto de falha mecânica (PFM. Por outro lado, o uso de correntes (CRT é estímulo com resistência variável (RV. Assim, objetivou-se avaliar os efeitos do CRT na altura e tempo de voo do salto vertical com contramovimento (CMJ. A partir de estudo de intervenção, 15 sujeitos foram avaliados quanto à carga máxima no agachamento (1RM e altura CMJ. Após isto, executaram três tipos de intervenções: i RF com 85% de 1RM; ii RV com 85% de 1RM posicionado no PFM (RV-TF e, iii RV com 85% de 1RM posicionado na maior extensão dos joelhos (RV-TV. Observou-se incremento do CMJ para RV-TF e RV-TV, mas não para RF. Conclui-se que houve PPA com os dois estímulos de CRT.La potenciación post-activación (PAP es estrategia para mejorar el rendimiento, utilizando una carga fija (RF, que se define en el punto de falla mecánica (PFM. Además, el uso de cadenas (CRT es estimulo con resistencia variable (RV. Así, el objetivo fue evaluar los efectos de la CRT en el salto vertical con contramovimiento (CMJ. Con estudio de intervención, 15 sujetos fueron evaluados acerca de la carga máxima en la sentadilla (1RM y altura en el CMJ. Después de eso, se realizaron tres tipos de intervenciones: i RF con el 85% de 1RM; ii RV con el 85% de 1RM en el PFM (RV-TF, y iii la RV en 1RM 85% situado en la mayor extensión de las rodillas (RV-TV. Se observó aumento de lo CMJ para RV-TF y RV-TV, pero no para la RF. Se concluye que existe PPA con los dos estímulos de RV.The Post-Activation Potentiation (PAP is a strategy to improve performance, using a fixed load (RF, defined at the sticking point (PFM. Moreover, the use of chains (CRT is an effort with variable resistance (RV. Thus, the objective was to evaluate the effects of CRT in the countermovement jump (CMJ. With an intervention study, 15 subjects were evaluated for the maximum squat load (1

Aerodynamic Optimization of Vertical Axis Wind Turbine with Trailing Edge Flap

DEFF Research Database (Denmark)

Ertem, Sercan; Ferreira, Carlos Simao; Gaunaa, Mac

2016-01-01

Vertical Axis Wind Turbines (VAWT) are competitive concepts for very large scale (10-20 MW)floating ofshore applications. Rotor circulation control (loading control) opens a wide design space to enhance the aerodynamic and operational features of VAWT. The modied linear derivation of the Actuator...

EVALUACIÓN DE LAS TÉCNICAS DE CEPILLADO DE BASS Y VERTICAL EN UN GRUPO DE PACIENTES EN TRATAMIENTO DE ORTODONCIA CON TÉCNICA MBT

Directory of Open Access Journals (Sweden)

Yelitza Ivone Baracaldo Ortíz

2012-12-01

Full Text Available Objetivo: Evaluar la efectividad de las técnicas de Cepillado de Bass y Vertical en pacientes con aparatología ortodóntica fija tratados con la técnica MBT. Materiales y métodos: se realizó un estudio experimental “In vivo” aleatorizado doble ciego; la muestra fue de 100 personas distribuidas en dos grupos, a cada uno se le asignó una Técnica de Cepillado y se dieron instrucciones de higiene oral por medio de charlas personalizadas y por escrito. Se usó el índice de Sillnes y Löe para medir el porcentaje de placa bacteriana, el cual fue realizado por una higienista oral, cada 30 ± 3 días durante 3 meses. A los dos grupos se les realizó profilaxis con el objetivo de tener un índice inicial de placa lo más aproximado a cero. A los participantes se les entregó mensualmente los aditamentos de higiene oral que debían usar. Resultados: antes de dar instrucciones de higiene oral el 73,4% tenían índice de placa moderado, el 16,46% severo y el 10,3% incipiente. El grupo de Técnica Vertical obtuvo mayor reducción de placa en comparación con el grupo de Técnica  Bass durante la primera toma (pConclusiones: La Técnica de Cepillado Vertical es más efectiva que la Técnica Bass para disminuir la placa bacteriana en pacientes tratados ortodónticamente con la técnica MBT.  

A 3D Vertically Integrated Deep N-Well CMOS MAPS for the SuperB Layer0

Energy Technology Data Exchange (ETDEWEB)

Traversi, G; Manghisoni, M; Re, V [University of Bergamo, Via Marconi 5, 24044 Dalmine (Italy); Gaioni, L; Ratti, L, E-mail: gianluca.traversi@unibg.it [INFN Pavia, Via Bassi 6, 27100 Pavia (Italy)

2011-01-15

Deep N-Well (DNW) Monolithic Active Pixel Sensors (MAPS) have been developed in the last few years with the aim of building monolithic sensors with similar functionalities as hybrid pixels systems. In these devices the triple well option, available in deep submicron processes, is exploited to implement analog and digital signal processing at the pixel level. Many prototypes have been fabricated in a planar (2D) 130nm CMOS technology. A new kind of DNW-MAPS, namely Apsel5{sub 3}D, which exploits the capabilities of vertical integration (3D) processes, is presented and discussed in this paper. The impact of 3D processes on the design and performance of DNW pixel sensors could be large, with significant advantages in terms of detection efficiency, pixel cell size and immunity to cross-talk, therefore complying with the severe constraints set by future HEP experiments.

Determination of the quark coupling strength vertical bar V-ub vertical bar using baryonic decays

NARCIS (Netherlands)

Aaij, R.; Adeva, B.; Adinolfi, M.; Older, A. A.; Ajaltouni, Z.; Akar, S.; Albrecht, J.; Alessio, F.; Alexander, M.; Ali, S.; Alkhazov, G.; Cartelle, P. Alvarez; Alves, A. A.; Amato, S.; Amerio, S.; Amhis, Y.; An, L.; Anderlini, L.; Andreotti, M.; Andrews, J. E.; Appleby, R. B.; Gutierrez, O. Aquines; Archilli, F.; Artamonov, A.; Artuso, M.; Aslanides, E.; Auriemma, G.; Baalouch, M.; Bachmann, S.; Back, J. J.; Badalov, A.; Baesso, C.; Baldini, W.; Barlow, R. J.; Barschel, C.; Barsuk, S.; Barter, W.; Batozskaya, V.; Battista, V.; Beaucourt, L.; Beddow, J.; Bedeschi, F.; Bediaga, I.; Bel, L. J.; Belyaev, I.; Ben-Haim, E.; Bencivenni, G.; Onderwater, C. J. G.; Pellegrino, A.; Tolk, S.

In the Standard Model of particle physics, the strength of the couplings of the b quark to the u and c quarks, vertical bar V-ub vertical bar and vertical bar V-ub vertical bar, are governed by the coupling of the quarks to the Higgs boson. Using data from the LHCb experiment at the Large Hadron

Dynamic Analysis of a Floating Vertical Axis Wind Turbine Under Emergency Shutdown Using Hydrodynamic Brake

DEFF Research Database (Denmark)

Wang, K.; Hansen, Martin Otto Laver; Moan, T.

2014-01-01

Emergency shutdown is always a challenge for an operating vertical axis wind turbine. A 5-MW vertical axis wind turbine with a Darrieus rotor mounted on a semi-submersible support structure was examined in this study. Coupled non-linear aero-hydro-servo-elastic simulations of the floating vertical...... axis wind turbine were carried out for emergency shutdown cases over a range of environmental conditions based on correlated wind and wave data. When generator failure happens, a brake should be applied to stop the acceleration of the rotor to prevent the rotor from overspeeding and subsequent disaster...

A global vertical reference frame based on four regional vertical datums

Czech Academy of Sciences Publication Activity Database

Burša, Milan; Kenyon, S.; Kouba, J.; Šíma, Zdislav; Vatrt, V.; Vojtíšková, M.

2004-01-01

Roč. 48, č. 3 (2004), s. 493-502 ISSN 0039-3169 Institutional research plan: CEZ:AV0Z1003909 Keywords : geopotentinal * local vertical datums * global vertical reference frame Subject RIV: BN - Astronomy, Celestial Mechanics, Astrophysics Impact factor: 0.447, year: 2004

Restrictions to Pharmacy Ownership and Vertical Integration in Estonia-Perception of Different Stakeholders.

Science.gov (United States)

Gross, Marit; Volmer, Daisy

2016-04-19

From 2020, the ownership of community pharmacies in Estonia will be limited to the pharmacy profession, and the vertical integration of wholesale companies and community pharmacies will not be allowed. The aim of this study was to evaluate the perception of different stakeholders in primary healthcare toward the new regulations of the community pharmacy sector in Estonia. A qualitative electronic survey was distributed to the main stakeholders in primary healthcare and higher education institutions providing pharmacy education ( n = 40) in May 2015. For data analysis, the systematic text condensation method was used. The study participants described two opposing positions regarding the development of community pharmacies in the future. Reform supporters emphasized increased professional independence and more healthcare-oriented operation of community pharmacies. Reform opponents argued against these ideas as community pharmacists do not have sufficient practical experience and finances to ensure sustainable development of the community pharmacy sector in Estonia. Based on the current perception of all respondents, the future operation of the community pharmacy sector in Estonia is unclear and there is urgent need for implementation criteria for the new regulations.

Effects of vertical positioning on gas exchange and lung volumes in acute respiratory distress syndrome.

Science.gov (United States)

Richard, Jean-Christophe M; Maggiore, Salvatore Maurizio; Mancebo, Jordi; Lemaire, François; Jonson, Bjorn; Brochard, Laurent

2006-10-01

Supine position may contribute to the loss of aerated lung volume in patients with acute respiratory distress syndrome (ARDS). We hypothesized that verticalization increases lung volume and improves gas exchange by reducing the pressure surrounding lung bases. Prospective observational physiological study in a medical ICU. In 16 patients with ARDS we measured arterial blood gases, pressure-volume curves of the respiratory system recorded from positive-end expiratory pressure (PEEP), and changes in lung volume in supine and vertical positions (trunk elevated at 45 degrees and legs down at 45 degrees ). Vertical positioning increased PaO(2) significantly from 94+/-33 to 142+/-49 mmHg, with an increase higher than 40% in 11 responders. The volume at 20 cmH(2)O measured on the PV curve from PEEP increased using the vertical position only in responders (233+/-146 vs. -8+/-9 1ml in nonresponders); this change was correlated to oxygenation change (rho=0.55). End-expiratory lung volume variation from supine to vertical and 1 h later back to supine, measured in 12 patients showed a significant increase during the 1-h upright period in responders (n=7) but not in nonresponders (n=5; 215+/-220 vs. 10+/-22 ml), suggesting a time-dependent recruitment. Vertical positioning is a simple technique that may improve oxygenation and lung recruitment in ARDS patients.

Envelope compact and solitary pattern structures for the GNLS(m,n,p,q) equations

International Nuclear Information System (INIS)

Yan Zhenya

2006-01-01

In this Letter, to further understand the role of nonlinear dispersion in the generalized nonlinear Schrodinger equation, we introduce and study the generalized nonlinear Schrodinger equation with nonlinear dispersion (called GNLS(m,n,p,q) equation): iu t +a(u vertical bar u vertical bar n-1 ) xx +bu vertical bar u vertical bar m-1 +ic(u vertical bar u vertical bar p-1 ) xxx +id(u vertical bar u vertical bar q-1 ) x =0. Some new envelope compacton solutions and solitary pattern solutions of GNLS(m,n,p,q) equation are obtained via the gauge transformation and some direct ansatze. In particular, it is shown that GNLS(m,n,p,q) equation with linear dispersion gives rise to envelope compactons and solitary patterns, which implies that nonlinear dispersion is not necessary condition for GNLS(m,n,p,q) equation to admit envelope compactons and solitary patterns. Moreover, some unusually local conservation laws are presented for GNLS + (n,n,n,n) equation and GNLS - (n,n,n,n) equation, respectively

Resonant Tunneling in Gated Vertical One- dimensional Structures

Science.gov (United States)

Kolagunta, V. R.; Janes, D. B.; Melloch, M. R.; Webb, K. J.

1997-03-01

Vertical sub-micron transistors incorporating resonant tunneling multiple quantum well heterostructures are interesting in applications for both multi-valued logic devices and the study of quantization effects in vertical quasi- one-, zero- dimensional structures. Earlier we have demonstrated room temperature pinch-off of the resonant peak in sub-micron vertical resonant tunneling transistors structures using a self-aligned sidewall gating technique ( V.R. Kolagunta et. al., Applied Physics Lett., 69), 374(1996). In this paper we present the study of gating effects in vertical multiple quantum well resonant tunneling transistors. Multiple well quasi-1-D sidewall gated transistors with mesa dimensions of L_x=0.5-0.9μm and L_y=10-40μm were fabricated. The quantum heterostructure in these devices consists of two non-symmetric (180 ÅÅi-GaAs wells separated from each other and from the top and bottom n^+ GaAs/contacts region using Al_0.3Ga_0.7As tunneling barriers. Room temperature pinch-off of the multiple resonant peaks similar to that reported in the case of single well devices is observed in these devices^1. Current-voltage characteristics at liquid nitrogen temperatures show splitting of the resonant peaks into sub-bands with increasing negative gate bias indicative of quasi- 1-D confinement. Room-temperature and low-temperature current-voltage measurements shall be presented and discussed.

Vertically Integrated Models for Carbon Storage Modeling in Heterogeneous Domains

Science.gov (United States)

Bandilla, K.; Celia, M. A.

2017-12-01

Numerical modeling is an essential tool for studying the impacts of geologic carbon storage (GCS). Injection of carbon dioxide (CO2) into deep saline aquifers leads to multi-phase flow (injected CO2 and resident brine), which can be described by a set of three-dimensional governing equations, including mass-balance equation, volumetric flux equations (modified Darcy), and constitutive equations. This is the modeling approach on which commonly used reservoir simulators such as TOUGH2 are based. Due to the large density difference between CO2 and brine, GCS models can often be simplified by assuming buoyant segregation and integrating the three-dimensional governing equations in the vertical direction. The integration leads to a set of two-dimensional equations coupled with reconstruction operators for vertical profiles of saturation and pressure. Vertically-integrated approaches have been shown to give results of comparable quality as three-dimensional reservoir simulators when applied to realistic CO2 injection sites such as the upper sand wedge at the Sleipner site. However, vertically-integrated approaches usually rely on homogeneous properties over the thickness of a geologic layer. Here, we investigate the impact of general (vertical and horizontal) heterogeneity in intrinsic permeability, relative permeability functions, and capillary pressure functions. We consider formations involving complex fluvial deposition environments and compare the performance of vertically-integrated models to full three-dimensional models for a set of hypothetical test cases consisting of high permeability channels (streams) embedded in a low permeability background (floodplains). The domains are randomly generated assuming that stream channels can be represented by sinusoidal waves in the plan-view and by parabolas for the streams' cross-sections. Stream parameters such as width, thickness and wavelength are based on values found at the Ketzin site in Germany. Results from the

Vertical integration

International Nuclear Information System (INIS)

Antill, N.

1999-01-01

This paper focuses on the trend in international energy companies towards vertical integration in the gas chain from wellhead to power generation, horizontal integration in refining and marketing businesses, and the search for larger projects with lower upstream costs. The shape of the petroleum industry in the next millennium, the creation of super-major oil companies, and the relationship between size and risk are discussed. The dynamics of vertical integration, present events and future developments are considered. (UK)

Spiral density waves and vertical circulation in protoplanetary discs

Science.gov (United States)

Riols, A.; Latter, H.

2018-06-01

Spiral density waves dominate several facets of accretion disc dynamics - planet-disc interactions and gravitational instability (GI) most prominently. Though they have been examined thoroughly in two-dimensional simulations, their vertical structures in the non-linear regime are somewhat unexplored. This neglect is unwarranted given that any strong vertical motions associated with these waves could profoundly impact dust dynamics, dust sedimentation, planet formation, and the emissivity of the disc surface. In this paper, we combine linear calculations and shearing box simulations in order to investigate the vertical structure of spiral waves for various polytropic stratifications and wave amplitudes. For sub-adiabatic profiles, we find that spiral waves develop a pair of counter-rotating poloidal rolls. Particularly strong in the non-linear regime, these vortical structures issue from the baroclinicity supported by the background vertical entropy gradient. They are also intimately connected to the disc's g modes which appear to interact non-linearly with the density waves. Furthermore, we demonstrate that the poloidal rolls are ubiquitous in gravitoturbulence, emerging in the vicinity of GI spiral wakes, and potentially transporting grains off the disc mid-plane. Other than hindering sedimentation and planet formation, this phenomena may bear on observations of the disc's scattered infrared luminosity. The vortical features could also impact on the turbulent dynamo operating in young protoplanetary discs subject to GI, or possibly even galactic discs.

Large N dynamics in QED in a magnetic field

International Nuclear Information System (INIS)

Gusynin, V.P.; Miransky, V.A.; Shovkovy, I.A.

2003-01-01

The expression for the dynamical mass of fermions in QED in a magnetic field is obtained for a large number of the fermion flavor N in the framework of 1/N expansion. The existence of a threshold value N thr , dividing the theories with essentially different dynamics, is established. For the number of flavors N thr , the dynamical mass is very sensitive to the value of the coupling constant α b , related to the magnetic scale μ=√(vertical bar eB vertical bar). For N of the order of N thr or larger, a dynamics similar to that in the Nambu-Jona-Lasinio model with a cutoff of the order of √(vertical bar eB vertical bar) and the dimensional coupling constant G∼1/(N vertical bar eB vertical bar) takes place. In this case, the value of the dynamical mass is essentially α b independent (the dynamics with an infrared stable fixed point). The value of N thr separates a weak coupling dynamics (with α-tilde b ≡Nα b b > or approx. 1) and is of the order of 1/α b

Strong photonic crystal behavior in regular arrays of core-shell and quantum disc InGaN/GaN nanorod light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Lewins, C. J., E-mail: c.j.lewins@bath.ac.uk; Le Boulbar, E. D.; Lis, S. M.; Shields, P. A.; Allsopp, D. W. E., E-mail: d.allsopp@bath.ac.uk [Department of Electronic and Electrical Engineering, University of Bath, Claverton Down, Bath BA2 7AY (United Kingdom); Edwards, P. R.; Martin, R. W. [Department of Physics, SUPA, University of Strathclyde, Glasgow G4 0NG (United Kingdom)

2014-07-28

We show that arrays of emissive nanorod structures can exhibit strong photonic crystal behavior, via observations of the far-field luminescence from core-shell and quantum disc InGaN/GaN nanorods. The conditions needed for the formation of directional Bloch modes characteristic of strong photonic behavior are found to depend critically upon the vertical shape of the nanorod sidewalls. Index guiding by a region of lower volume-averaged refractive index near the base of the nanorods creates a quasi-suspended photonic crystal slab at the top of the nanorods which supports Bloch modes. Only diffractive behavior could be observed without this region. Slab waveguide modelling of the vertical structure shows that the behavioral regime of the emissive nanorod arrays depends strongly upon the optical coupling between the nanorod region and the planar layers below. The controlled crossover between the two regimes of photonic crystal operation enables the design of photonic nanorod structures formed on planar substrates that exploit either behavior depending on device requirements.

Non-protected operators in N=4 SYM and multiparticle states of AdS5 SUGRA

International Nuclear Information System (INIS)

Arutyunov, G.; Penati, S.; Petkou, A.C.; Santambrogio, A.; Sokatchev, E.

2002-01-01

We study a class of non-protected local composite operators which occur in the R-symmetry singlet channel of the OPE of two stress-tensor multiplets in N=4 SYM. At tree level these are quadrilinear scalar dimension four operators, two single-traces and two double-traces. In the presence of interaction, due to a non-trivial mixing under renormalization, they split into linear combinations of conformally covariant operators. We resolve the mixing by computing the one-loop two-point functions of all the operators in an N=1 setup, then diagonalizing the anomalous dimension matrix and identifying the quasiprimary operators. We find one operator whose anomalous dimension is negative and suppressed by a factor of 1/N 2 with respect to the anomalous dimensions of the Konishi-like operators. We reveal the mechanism responsible for this suppression and argue that it works at every order in perturbation theory. In the context of the AdS/CFT correspondence such an operator should be dual to a multiparticle supergravity state whose energy is less than the sum of the corresponding individual single-particle states

The WZNW model on PSU(1, 1 vertical stroke 2)

International Nuclear Information System (INIS)

Goetz, G.

2006-10-01

According to the work of Berkovits, Vafa and Witten, the non-linear sigma model on the supergroup PSU(1,1 vertical stroke 2) is the essential building block for string theory on AdS 3 xS 3 xT 4 . Models associated with a non-vanishing value of the RR flux can be obtained through a psu(1,1 vertical stroke 2) invariant marginal deformation of the WZNW model on PSU(1,1 vertical stroke 2). We take this as a motivation to present a manifestly psu(1,1 vertical stroke 2) covariant construction of the model at the Wess-Zumino point, corresponding to a purely NSNS background 3-form flux. At this point the model possesses an enhanced psu(1,1 vertical stroke 2) current algebra symmetry whose representation theory, including explicit character formulas, is developed systematically in the first part of the paper. The space of vertex operators and a free fermion representation for their correlation functions is our main subject in the second part. Contrary to a widespread claim, bosonic and fermionic fields are necessarily coupled to each other. The interaction changes the supersymmetry transformations, with drastic consequences for the multiplets of localized normalizable states in the model. It is only this fact which allows us to decompose the full state space into multiplets of the global supersymmetry. We analyze these decompositions systematically as a preparation for a forthcoming study of the RR deformation. (orig.)

The WZNW model on PSU(1, 1 vertical stroke 2)

Energy Technology Data Exchange (ETDEWEB)

Goetz, G. [CEA Centre d' Etudes de Saclay, 91 - Gif-sur-Yvette (France). Service de Physique Theorique; Quella, T. [King' s College London (United Kingdom). Dept. of Mathematics]|[Amsterdam Univ. (Netherlands). KdV Institute for Mathematics; Schomerus, V. [CEA Centre d' Etudes de Saclay, 91 - Gif-sur-Yvette (France). Service de Physique Theorique]|[Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

2006-10-15

According to the work of Berkovits, Vafa and Witten, the non-linear sigma model on the supergroup PSU(1,1 vertical stroke 2) is the essential building block for string theory on AdS{sub 3}xS{sup 3}xT{sup 4}. Models associated with a non-vanishing value of the RR flux can be obtained through a psu(1,1 vertical stroke 2) invariant marginal deformation of the WZNW model on PSU(1,1 vertical stroke 2). We take this as a motivation to present a manifestly psu(1,1 vertical stroke 2) covariant construction of the model at the Wess-Zumino point, corresponding to a purely NSNS background 3-form flux. At this point the model possesses an enhanced psu(1,1 vertical stroke 2) current algebra symmetry whose representation theory, including explicit character formulas, is developed systematically in the first part of the paper. The space of vertex operators and a free fermion representation for their correlation functions is our main subject in the second part. Contrary to a widespread claim, bosonic and fermionic fields are necessarily coupled to each other. The interaction changes the supersymmetry transformations, with drastic consequences for the multiplets of localized normalizable states in the model. It is only this fact which allows us to decompose the full state space into multiplets of the global supersymmetry. We analyze these decompositions systematically as a preparation for a forthcoming study of the RR deformation. (orig.)

Selección preliminar de plantas de arroz con resistencia vertical A pyricularia oryzae Cav por inducción de mutaciones (ING

Directory of Open Access Journals (Sweden)

A Cruz

2016-03-01

Full Text Available Seeds of rice Oryza sativa L. cv. CR-1113 susceptible to blast disease Pyricularia oryzae Cav. Were subjected to gamma radiation with 60Co using doses of 15 and 20 krads to obtain and select mutant plants with vertical resistance to blast. A total of 80.000 rice plants per treatment were individually evaluated in the second mutant generation (M2 at tillering and panicle emergence. Vertical resistance was observed in 47 and 8 plants from the 15 and 20 krads treatments respectively.

Innovative Design of a Darrieus Straight Bladed Vertical Axis Wind Turbine by using Multi Element Airfoil

DEFF Research Database (Denmark)

Chougle, Prasad Devendra

. Mainly, there is the horizontal axis wind turbine (HAWT) and vertical axis wind turbine (VAWT). HAWTs are more popular than VAWTs due to failure of VAWT commercialization during the late of 1980s on a large scale. However, in recent research work it has been documented that VAWTs are more economical......, and the wind tunnel testing of double-element airfoil is performed. It is found that the aerodynamic characteristics of the airfoil increased considerably by delaying the angle of stall. These two facts are very suitable for vertical axis wind turbine since they operate in a larger range of angle of attack......, ±40_, compared to the horizontal axis wind turbines which operate in the range of attack, ±15_. A new design of vertical axis wind turbine is then proposed, and aerodynamic performance is evaluated based on double multiple stream tube methods. The performance parameters are almost doubled compared...

Enhanced field emission properties of vertically aligned double-walled carbon nanotube arrays

International Nuclear Information System (INIS)

Chen, Guohai; Shin, Dong Hoon; Lee, Cheol Jin; Iwasaki, Takayuki; Kawarada, Hiroshi

2008-01-01

Vertically aligned double-walled carbon nanotube (VA-DWCNT) arrays were synthesized by point-arc microwave plasma chemical vapor deposition on Cr/n-Si and SiO 2 /n-Si substrates. The outer tube diameters of VA-DWCNTs are in the range of 2.5-3.8 nm, and the average interlayer spacing is approximately 0.42 nm. The field emission properties of these VA-DWCNTs were studied. It was found that a VA-DWCNT array grown on a Cr/n-Si substrate had better field emission properties as compared with a VA-DWCNT array grown on a SiO 2 /n-Si substrate and randomly oriented DWCNTs, showing a turn-on field of about 0.85 V μm -1 at the emission current density of 0.1 μA cm -2 and a threshold field of 1.67 V μm -1 at the emission current density of 1.0 mA cm -2 . The better field emission performance of the VA-DWCNT array was mainly attributed to the vertical alignment of DWCNTs on the Cr/n-Si substrate and the low contact resistance between CNTs and the Cr/n-Si substrate

Overview and Design of self-acting pitch control mechanism for vertical axis wind turbine using multi body simulation approach

DEFF Research Database (Denmark)

Chougule, Prasad; Nielsen, Søren R.K.

2014-01-01

Awareness about wind energy is constantly growing in the world. Especially a demand for small scale wind turbine is increasing and various products are available in market. There are mainly two types of wind turbines, horizontal axis wind turbine and vertical axis wind turbines. Horizontal axis...... wind turbines are suitable for high wind speed whereas vertical axis wind turbines operate relatively low wind speed area. Vertical axis wind turbines are cost effective and simple in construction as compared to the horizontal axis wind turbine. However, vertical axis wind turbines have inherent...

Long-term global response analysis of a vertical axis wind turbine supported on a semi-submersible floating platform: Comparison between operating and non-operating wind turbine load cases

DEFF Research Database (Denmark)

Collu, Maurizio; Manuel, Lance; Borg, Michael

2015-01-01

This study continues [1] the examination of the long-term global response of a floating vertical axis wind turbine (VAWT) situated off the Portuguese coast in the Atlantic Ocean. The VAWT, which consists of a 5-MW 3-bladed H-type rotor developed as part of the EU-FP7 H2OCEAN project, is assumed...... is adopted, as well as also taking into account the drag generated by the wind turbine tower. Short-term turbine load and platform motion statistics are established for individual sea states that are analysed. The long-term reliability yields estimates of 50-year loads and platform motions that takes...... to be mounted on the OC4 semi-submersible floating platform. Adding a non-operational load case (wind speed 35m/s), the sea states identified are used to carry out coupled dynamics simulations using the FloVAWT design tool, for which an improved wave elevation and relative force/moment time signals approach...

Application of computational fluid dynamics (CFD) simulation in a vertical axis wind turbine (VAWT) system

Science.gov (United States)

Kao, Jui-Hsiang; Tseng, Po-Yuan

2018-01-01

The objective of this paper is to describe the application of CFD (Computational fluid dynamics) technology in the matching of turbine blades and generator to increase the efficiency of a vertical axis wind turbine (VAWT). A VAWT is treated as the study case here. The SST (Shear-Stress Transport) k-ω turbulence model with SIMPLE algorithm method in transient state is applied to solve the T (torque)-N (r/min) curves of the turbine blades at different wind speed. The T-N curves of the generator at different CV (constant voltage) model are measured. Thus, the T-N curves of the turbine blades at different wind speed can be matched by the T-N curves of the generator at different CV model to find the optimal CV model. As the optimal CV mode is selected, the characteristics of the operating points, such as tip speed ratio, revolutions per minute, blade torque, and efficiency, can be identified. The results show that, if the two systems are matched well, the final output power at a high wind speed of 9-10 m/s will be increased by 15%.

Structure of N = 2 superconformally invariant unitary ''minimal'' theories: Operator algebra and correlation functions

International Nuclear Information System (INIS)

Kiritsis, E.B.

1987-01-01

N = 2 superconformal-invariant theories are studied and their general structure is analyzed. The geometry of N = 2 complex superspace is developed as a tool to study the correlation functions of the theories above. The Ward identities of the global N = 2 superconformal symmetry are solved, to restrict the form of correlation functions. Advantage is taken of the existence of the degenerate operators to derive the ''fusion'' rules for the unitary minimal systems with c<1. In particular, the closure of the operator algebra for such systems is shown. The c = (1/3 minimal system is analyzed and its two-, three-, and four-point functions as well as its operator algebra are calculated explicitly

Vertically stacked nanocellulose tactile sensor.

Science.gov (United States)

Jung, Minhyun; Kim, Kyungkwan; Kim, Bumjin; Lee, Kwang-Jae; Kang, Jae-Wook; Jeon, Sanghun

2017-11-16

Paper-based electronic devices are attracting considerable attention, because the paper platform has unique attributes such as flexibility and eco-friendliness. Here we report on what is claimed to be the firstly fully integrated vertically-stacked nanocellulose-based tactile sensor, which is capable of simultaneously sensing temperature and pressure. The pressure and temperature sensors are operated using different principles and are stacked vertically, thereby minimizing the interference effect. For the pressure sensor, which utilizes the piezoresistance principle under pressure, the conducting electrode was inkjet printed on the TEMPO-oxidized-nanocellulose patterned with micro-sized pyramids, and the counter electrode was placed on the nanocellulose film. The pressure sensor has a high sensitivity over a wide range (500 Pa-3 kPa) and a high durability of 10 4 loading/unloading cycles. The temperature sensor combines various materials such as poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS), silver nanoparticles (AgNPs) and carbon nanotubes (CNTs) to form a thermocouple on the upper nanocellulose layer. The thermoelectric-based temperature sensors generate a thermoelectric voltage output of 1.7 mV for a temperature difference of 125 K. Our 5 × 5 tactile sensor arrays show a fast response, negligible interference, and durable sensing performance.

Feedback control of vertical instability in TNS

International Nuclear Information System (INIS)

Frantz, E.R.

1978-05-01

Due to the unfavorable curvature of the vertical vacuum magnetic field, elongated plasmas are vertically unstable when the elongation, epsilon, becomes too large. The TNS (The Next Step) tokamak, as evolved in the Westinghouse-ORNL studies has an inside-D configuration (epsilon = 1.6, A = 5/1.25 = 4) characterized by an average decay index n approximately equal -0.75 at the plasma flux surface near the magnetic axis and is vertically unstable with a growth rate γ 0 approximately 10 5 sec -1 . Eddy currents produced in the vacuum vessel wall will slow this instability to growth rates γ 0 approximately 10 2 sec -1 provided there are no transverse insulating gaps in the vessel wall. A matrix equation has been developed for calculating the eddy currents induced in the EF coils and their stabilizing effect. Control theory for feedback systems with and without delay time is presented and possible plasma position detectors are discussed. For a plasma current of 6.1 MA, the controller peak power requirements using separate controller circuits are approximately 1 MW depending upon EF coil configurations and time delay. This feedback system is designed to stabilize a maximum plasma excursion of 10 cm from the midplane with delay times up to 2 sec

Demonstration of an Enhanced Vertical Magnetic Gradient System for UXO

Science.gov (United States)

2008-12-01

fluxgate magnetometers , data recording console, laser altimeter, and acoustic altimeters were tested to ensure proper operation and performance. The VG...Simultaneous Electromagnetic Induction and Magnetometer System WAA wide area assessment ACKNOWLEDGEMENTS We wish to express our sincere...sensors. The benefits of vertical gradient (VG) configurations in magnetometer systems are common knowledge, and these configurations are routinely

Description of the IMR Standard Light Trap and the Vertical ...

African Journals Online (AJOL)

The construction of different versions of a cheap, robust, and easy to operate light trap for catching various aquatic organisms is shown. The trap can be used to > 300 m depth and meets a number of criteria. Small-scale vertical distribution of decapod larvae was investigated during trap trials. The traps (6-10) were set for 24 ...

Managed care, vertical integration strategies and hospital performance.

Science.gov (United States)

Wang, B B; Wan, T T; Clement, J; Begun, J

2001-09-01

The purpose of this study is to examine the association of managed care with hospital vertical integration strategies, as well as to observe the relationships of different types of vertical integration with hospital efficiency and financial performance. The sample consists of 363 California short-term acute care hospitals in 1994. Linear structure equation modeling is used to test six hypotheses derived from the strategic adaptation model. Several organizational and market factors are controlled statistically. Results suggest that managed care is a driving force for hospital vertical integration. In terms of performance, hospitals that are integrated with physician groups and provide outpatient services (backward integration) have better operating margins, returns on assets, and net cash flows (p < 0.01). These hospitals are not, however, likely to show greater productivity. Forward integration with a long-term-care facility, on the other hand, is positively and significantly related to hospital productivity (p < 0.001). Forward integration is negatively related to financial performance (p < 0.05), however, opposite to the direction hypothesized. Health executives should be responsive to the growth of managed care in their local market and should probably consider providing more backward integrated services rather than forward integrated services in order to improve the hospital's financial performance in today's competitive health care market.

Efficient strategy to Cu/Si catalyst into vertically aligned carbon ...

Indian Academy of Sciences (India)

Abstract. Bamboo-shaped vertically aligned carbon nanotubes (bs-VACNTs) were fabricated on Cu/Si catalyst by ... on Si wafer material when compared to the other commer- ..... [3] Li H, Zhao N, He C, Shi C, Du X, Li J and Cui Q 2008 Mater.

Vertical circulation and thermospheric composition: a modelling study

Directory of Open Access Journals (Sweden)

H. Rishbeth

Full Text Available The coupled thermosphere-ionosphere-plasmasphere model CTIP is used to study the global three-dimensional circulation and its effect on neutral composition in the midlatitude F-layer. At equinox, the vertical air motion is basically up by day, down by night, and the atomic oxygen/molecular nitrogen [O/N₂] concentration ratio is symmetrical about the equator. At solstice there is a summer-to-winter flow of air, with downwelling at subauroral latitudes in winter that produces regions of large [O/N₂] ratio. Because the thermospheric circulation is influenced by the high-latitude energy inputs, which are related to the geometry of the Earth's magnetic field, the latitude of the downwelling regions varies with longitude. The downwelling regions give rise to large F2-layer electron densities when they are sunlit, but not when they are in darkness, with implications for the distribution of seasonal and semiannual variations of the F2-layer. It is also found that the vertical distributions of O and N₂ may depart appreciably from diffusive equilibrium at heights up to about 160 km, especially in the summer hemisphere where there is strong upwelling.

Atmospheric composition and structure (thermosphere · composition and chemistry · Ionosphere (ionosphere · atmosphere interactions

A first-principles analysis of ballistic conductance, grain boundary scattering and vertical resistance in aluminum interconnects

Science.gov (United States)

Zhou, Tianji; Lanzillo, Nicholas A.; Bhosale, Prasad; Gall, Daniel; Quon, Roger

2018-05-01

We present an ab initio evaluation of electron scattering mechanisms in Al interconnects from a back-end-of-line (BEOL) perspective. We consider the ballistic conductance as a function of nanowire size, as well as the impact of surface oxidation on electron transport. We also consider several representative twin grain boundaries and calculate the specific resistivity and reflection coefficients for each case. Lastly, we calculate the vertical resistance across the Al/Ta(N)/Al and Cu/Ta(N)/Cu interfaces, which are representative of typical vertical interconnect structures with diffusion barriers. Despite a high ballistic conductance, the calculated specific resistivities at grain boundaries are 70-100% higher in Al than in Cu, and the vertical resistance across Ta(N) diffusion barriers are 60-100% larger for Al than for Cu. These results suggest that in addition to the well-known electromigration limitations in Al interconnects, electron scattering represents a major problem in achieving low interconnect line resistance at fine dimensions.

Low-voltage operating flexible ferroelectric organic field-effect transistor nonvolatile memory with a vertical phase separation P(VDF-TrFE-CTFE)/PS dielectric

Science.gov (United States)

Xu, Meili; Xiang, Lanyi; Xu, Ting; Wang, Wei; Xie, Wenfa; Zhou, Dayu

2017-10-01

Future flexible electronic systems require memory devices combining low-power operation and mechanical bendability. However, high programming/erasing voltages, which are universally needed to switch the storage states in previously reported ferroelectric organic field-effect transistor (Fe-OFET) nonvolatile memories (NVMs), severely prevent their practical applications. In this work, we develop a route to achieve a low-voltage operating flexible Fe-OFET NVM. Utilizing vertical phase separation, an ultrathin self-organized poly(styrene) (PS) buffering layer covers the surface of the ferroelectric polymer layer by one-step spin-coating from their blending solution. The ferroelectric polymer with a low coercive field contributes to low-voltage operation in the Fe-OFET NVM. The polymer PS contributes to the improvement of mobility, attributing to screening the charge scattering and decreasing the surface roughness. As a result, a high performance flexible Fe-OFET NVM is achieved at the low P/E voltages of ±10 V, with a mobility larger than 0.2 cm2 V-1 s-1, a reliable P/E endurance over 150 cycles, stable data storage retention capability over 104 s, and excellent mechanical bending durability with a slight performance degradation after 1000 repetitive tensile bending cycles at a curvature radius of 5.5 mm.

Adaptation of the vertical vestibulo-ocular reflex in cats during low-frequency vertical rotation.