Environmental labeling of car tires--toxicity to Daphnia magna can be used as a screening method.

Science.gov (United States)

Wik, Anna; Dave, Göran

2005-02-01

Car tires contain several water-soluble compounds that can leach into water and have toxic effects on aquatic organisms. Due to tire wear, 10,000 tonnes of rubber particles end up along the Swedish roads every year. This leads to a diffuse input of emissions of several compounds. Emissions of polyaromatic hydrocarbons (PAHs) are of particular concern. PAHs are ingredients of the high aromatic oil (HA oil) that is used in the rubber as a softener and as a filler. The exclusion of HA oils from car tires has started, and an environmental labeling of tires could make HA oils obsolete. The toxicity to Daphnia magna from 12 randomly selected car tires was tested in this study. Rubber from the tread of the tires was grated into small pieces, to simulate material from tire wear, and the rubber was equilibrated with dilution water for 72 h before addition of test organisms. The 24-h EC50s of the rubber pieces ranged from 0.29 to 32 gl-1, and the 48-h EC50s ranged from 0.0625 to 2.41 gl-1. Summer tires were more toxic than winter tires. After the 48-h exposure, the daphnids were exposed to UV-light for 2 h, to determine if the tires contained compounds that were phototoxic. After UV-activation the EC50s ranged from 0.0625 to 0.38 gl-1. Four of the 12 tires had a very distinct photoactivation, with a toxicity increase of >10 times. This study has shown that the used method for toxicity testing with Daphnia magna according to ISO 6341 could be used as a basis for environmental labeling of car tires.

78 FR 47050 - Cooper Tire & Rubber Company, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2013-08-02

..., and tread wear, temperature, and traction ratings to assess performance capabilities of various tires...-0109; Notice 2] Cooper Tire & Rubber Company, Grant of Petition for Decision of Inconsequential...: Cooper Tire & Rubber Company (Cooper) \\1\\ has determined that certain Cooper brand replacement tires...

Tire wear particles in the aquatic environment - A review on generation, analysis, occurrence, fate and effects.

Science.gov (United States)

Wagner, Stephan; Hüffer, Thorsten; Klöckner, Philipp; Wehrhahn, Maren; Hofmann, Thilo; Reemtsma, Thorsten

2018-08-01

Tire wear particles (TWP), generated from tire material during use on roads have gained increasing attention as part of organic particulate contaminants, such as microplastic, in aquatic environments. The available information on properties and generation of TWP, analytical techniques to determine TWP, emissions, occurrence and behavior and ecotoxicological effects of TWP are reviewed with a focus on surface water as a potential receptor. TWP emissions are traffic related and contribute 5-30% to non-exhaust emissions from traffic. The mass of TWP generated is estimated at 1,327,000 t/a for the European Union, 1,120,000 t/a for the United States and 133,000 t/a for Germany. For Germany, this is equivalent to four times the amount of pesticides used. The mass of TWP ultimately entering the aquatic environment strongly depends on the extent of collection and treatment of road runoff, which is highly variable. For the German highways it is estimated that up to 11,000 t/a of TWP reach surface waters. Data on TWP concentrations in the environment, including surface waters are fragmentary, which is also due to the lack of suitable analytical methods for their determination. Information on TWP properties such as density and size distribution are missing; this hampers assessing the fate of TWP in the aquatic environment. Effects in the aquatic environment may stem from TWP itself or from compounds released from TWP. It is concluded that reliable knowledge on transport mechanism to surface waters, concentrations in surface waters and sediments, effects of aging, environmental half-lives of TWP as well as effects on aquatic organisms are missing. These aspects need to be addressed to allow for the assessment of risk of TWP in an aquatic environment. Copyright © 2018 Elsevier Ltd. All rights reserved.

75 FR 17827 - Goodyear Tire & Rubber Company, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2010-04-07

... Motor Vehicle Safety performance standards. All of the markings related to tire service (load capacity..., and tread wear, temperature, and traction ratings, to assess performance capabilities of various tires...-0213; Notice 2] Goodyear Tire & Rubber Company, Grant of Petition for Decision of Inconsequential...

78 FR 47049 - Bridgestone Americas Tire Operations, LLC, Grant of Petition for Decision of Inconsequential...

Science.gov (United States)

2013-08-02

... on the operational performance or safety of vehicles on which these tires are mounted. Bridgestone..., and tread wear, temperature, and traction ratings to assess performance capabilities of various tires...-0108; Notice 2] Bridgestone Americas Tire Operations, LLC, Grant of Petition for Decision of...

Analysis of Tire Contact Parameters Using Visual Processing

Directory of Open Access Journals (Sweden)

Valentin Ivanov

2010-01-01

The first part of this paper presents the results of experimental estimation of the contact patch area depending on the normal wheel load and inflation pressure for different car tires. The data were obtained for test bench conditions on the basis of the visual processing of tread footprint. Further, the contact length in the cohesion area during wheel rolling for single points on the tire profile has been chosen as a benchmark criterion. This paper has analyzed the influence of the wheel normal load and tire inflation pressure on the contact length with small rolling velocities. The results of the investigations are given for winter and racing tires with different grades of wear.

76 FR 73007 - Goodyear Tire and Rubber Company, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2011-11-28

... tread wear, temperature, and traction ratings, to assess performance capabilities of various tires. In...-0080; Notice 2] Goodyear Tire and Rubber Company, Grant of Petition for Decision of Inconsequential... Decision of Inconsequential Noncompliance. SUMMARY: Goodyear Tire and Rubber Company, (Goodyear),\\1\\ has...

Optical strain measurement for fault detection in haul-truck tires

International Nuclear Information System (INIS)

Kotchon, A; Nobes, D S; Lipsett, M G

2012-01-01

Tire condition is integral to the safe operation of heavy machinery, such as ultra-class haul trucks. A new approach to haul truck tire monitoring is being investigated based on optical strain measurement, which has the advantage of providing quantitative information from sensors that do not contact the tire. A laboratory-scale apparatus has been constructed to monitor a tire as it is subjected to various loads and pressures. Digital image correlation is used to calculate the deformation in the tire. Using this method, damage resulting from a horizontal and vertical cut created on the tire surface could be detected. A three-dimensional surface reconstruction of the tire was created to assist in the characterization of more complex damage types such as wear and fatigue. In addition to providing information for a possible industrial scale damage detection system, this apparatus will also further the understanding of damage mechanisms in tires.

Environmental impact caused by incorrect discard of tires

Directory of Open Access Journals (Sweden)

Vitória Emanuella da Silva Alves

2015-11-01

Full Text Available Tires are wastes that need special treatment, because when buried whole, its shape facilitates the accumulation of gases from the decomposition of other waste and in case of emerge surface provides shelter for diseases. Thus, this research aimed to provide information about the environmental impacts caused by the improper disposal of unserviceable tires and about some techniques for reusing and recycling them. We opted for the literature search using databases SCIELO, GOOGLE SCHOLAR, CAPES journals, resolutions of the MMA, the ANIP and regulations of IBAMA instructions. The consultation material comprises a period from 1992 to 2015 with the following descriptors: industrial waste; laws of tires; environmental impacts caused by improper disposal of tires and technological alternatives usable by tires and scrap therefore improper disposal of scrap tires can cause negative impacts such as floods, by reducing the flow capacity of water bodies and drains. In contrast, after use, the tire can undergo reform and be reused, but the wear out is completely characterized as waste tire and the correct disposal are the possible ways of recycling. Thus it is very important compliance of laws that deal with the proper disposal of tires.

Impacts of weathered tire debris on the development of Rana sylvatica larvae.

Science.gov (United States)

Camponelli, Kimberly M; Casey, Ryan E; Snodgrass, Joel W; Lev, Steven M; Landa, Edward R

2009-02-01

Highway runoff has the potential to negatively impact receiving systems including stormwater retention ponds where highway particulate matter can accumulate following runoff events. Tire wear particles, which contain about 1% Zn by mass, make up approximately one-third of the vehicle derived particulates in highway runoff and therefore may serve as a stressor to organisms utilizing retention ponds as habitat. In this study, we focused on the potential contribution of tire debris to Zn accumulation by Rana sylvatica larvae and possible lethal or sublethal impacts resulting from exposure to weathered tire debris during development. Eggs and larvae were exposed to aged sediments (containing either ZnCl2 or tire particulate matter, both providing nominal concentrations of 1000 mg Zn kg(-1)) through metamorphosis. Water column Zn was elevated in both the ZnCl2 and tire treatments relative to the control treatment, indicating that aging allowed Zn leaching from tire debris to occur. Tissue Zn was also elevated for the ZnCl2 and tire treatments indicating that Zn in the treatments was available for uptake by the amphibians. Exposure to both ZnCl2 and tire treatments increased the time for larvae to complete metamorphosis in comparison with controls. We also observed that the longer the organisms took to complete metamorphosis, the smaller their mass at metamorphosis. Our results indicate that Zn leached from aged tire debris is bioavailable to developing R. sylvatica larvae and that exposure to tire debris amended sediments can result in measurable physiological outcomes to wood frogs that may influence population dynamics.

Impacts of weathered tire debris on the development of Rana sylvatica larvae

Science.gov (United States)

Camponelli, K.M.; Casey, R.E.; Snodgrass, J.W.; Lev, S.M.; Landa, E.R.

2009-01-01

Highway runoff has the potential to negatively impact receiving systems including stormwater retention ponds where highway particulate matter can accumulate following runoff events. Tire wear particles, which contain about 1% Zn by mass, make up approximately one-third of the vehicle derived particulates in highway runoff and therefore may serve as a stressor to organisms utilizing retention ponds as habitat. In this study, we focused on the potential contribution of tire debris to Zn accumulation by Rana sylvatica larvae and possible lethal or sublethal impacts resulting from exposure to weathered tire debris during development. Eggs and larvae were exposed to aged sediments (containing either ZnCl2 or tire particulate matter, both providing nominal concentrations of 1000 mg Zn kg-1) through metamorphosis. Water column Zn was elevated in both the ZnCl2 and tire treatments relative to the control treatment, indicating that aging allowed Zn leaching from tire debris to occur. Tissue Zn was also elevated for the ZnCl2 and tire treatments indicating that Zn in the treatments was available for uptake by the amphibians. Exposure to both ZnCl2 and tire treatments increased the time for larvae to complete metamorphosis in comparison with controls. We also observed that the longer the organisms took to complete metamorphosis, the smaller their mass at metamorphosis. Our results indicate that Zn leached from aged tire debris is bioavailable to developing R. sylvatica larvae and that exposure to tire debris amended sediments can result in measurable physiological outcomes to wood frogs that may influence population dynamics. ?? 2008 Elsevier Ltd.

77 FR 2775 - Goodyear Tire and Rubber Company, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2012-01-19

... tread wear, temperature, and traction ratings, to assess performance capabilities of various tires. In...-0033; Notice 2] Goodyear Tire and Rubber Company, Grant of Petition for Decision of Inconsequential.... SUMMARY: Goodyear Tire and Rubber Company,(Goodyear),\\1\\ has determined that approximately 26,224 Goodyear...

Tire wear emissions for asphalt rubber and Portland cement concrete pavement surfaces.

Science.gov (United States)

2006-04-01

Since 1990, it has been the policy of the State of Arizona that the recycling and reuse of : waste tires are the highest priority. The Arizona Department of Transportation (ADOT) : has long supported the use of recycled waste tire rubber in asphalt r...

Experimental methodology for assessing the environmental fate of organic chemicals in polymer matrices using column leaching studies and OECD 308 water/sediment systems: Application to tire and road wear particles.

Science.gov (United States)

Unice, Kenneth M; Bare, Jennifer L; Kreider, Marisa L; Panko, Julie M

2015-11-15

Automobile tires require functional rubber additives including curing agents and antioxidants, which are potentially environmentally available from tire and road wear particles (TRWP) deposited in soil and sediment. A novel methodology was employed to evaluate the environmental fate of three commonly-used tire chemicals (N-cyclohexylbenzothiazole-2-sulfenamide (CBS), N-(1,3-dimethylbutyl)-N'-phenyl-1,4-phenylenediamine (6-PPD) and 1,3-diphenylguanidine (DPG)), using a road simulator, an artificial weathering chamber, column leaching tests, and OECD 308 sediment/water incubator studies. Environmental release factors were quantified for curing (f(C)), tire wear (f(W)), terrestrial weathering (f(S)), leaching from TRWP (f(L)), and environmental availability from TRWP (f(A)) by liquid chromatography-tandem mass spectroscopy (LC/MS/MS) analyses. Cumulative fractions representing total environmental availability (F(T)) and release to water (FR) were calculated for the tire chemicals and 13 transformation products. F(T) for CBS, DPG and 6-PPD inclusive of transformation products for an accelerated terrestrial aging time in soil of 0.1 years was 0.08, 0.1, and 0.06, respectively (equivalent to 6 to 10% of formulated mass). In contrast, a wider range of 5.5×10(-4) (6-PPD) to 0.06 (CBS) was observed for F(R) at an accelerated age of 0.1 years, reflecting the importance of hydrophobicity and solubility for determining the release to the water phase. Significant differences (p<0.05) in the weathering factor, f(S), were observed when chemicals were categorized by boiling point or hydrolysis rate constant. A significant difference in the leaching factor, f(L), and environmental availability factor, f(A), was also observed when chemicals were categorized by log K(ow). Our methodology should be useful for lifecycle analysis of other functional polymer chemicals. Copyright © 2015 Elsevier B.V. All rights reserved.

Measurement of airborne concentrations of tire and road wear particles in urban and rural areas of France, Japan, and the United States

Science.gov (United States)

Panko, Julie M.; Chu, Jennifer; Kreider, Marisa L.; Unice, Ken M.

2013-06-01

In addition to industrial facilities, fuel combustion, forest fires and dust erosion, exhaust and non-exhaust vehicle emissions are an important source of ambient air respirable particulate matter (PM10). Non-exhaust vehicle emissions are formed from wear particles of vehicle components such as brakes, clutches, chassis and tires. Although the non-exhaust particles are relatively minor contributors to the overall ambient air particulate load, reliable exposure estimates are few. In this study, a global sampling program was conducted to quantify tire and road wear particles (TRWP) in the ambient air in order to understand potential human exposures and the overall contribution of these particles to the PM10. The sampling was conducted in Europe, the United States and Japan and the sampling locations were selected to represent a variety of settings including both rural and urban core; and within each residential, commercial and recreational receptors. The air samples were analyzed using validated chemical markers for rubber polymer based on a pyrolysis technique. Results indicated that TRWP concentrations in the PM10 fraction were low with averages ranging from 0.05 to 0.70 μg m-3, representing an average PM10 contribution of 0.84%. The TRWP concentration in air was associated with traffic load and population density, but the trend was not statistically significant. Further, significant differences across days were not observed. This study provides a robust dataset to understand potential human exposures to airborne TRWP.

Comparison of tire and road wear particle concentrations in sediment for watersheds in France, Japan, and the United States by quantitative pyrolysis GC/MS analysis.

Science.gov (United States)

Unice, Ken M; Kreider, Marisa L; Panko, Julie M

2013-08-06

Impacts of surface runoff to aquatic species are an ongoing area of concern. Tire and road wear particles (TRWP) are a constituent of runoff, and determining accurate TRWP concentrations in sediment is necessary in order to evaluate the likelihood that these particles present a risk to the aquatic environment. TRWP consist of approximately equal mass fractions of tire tread rubber and road surface mineral encrustations. Sampling was completed in the Seine (France), Chesapeake (U.S.), and Yodo-Lake Biwa (Japan) watersheds to quantify TRWP in the surficial sediment of watersheds characterized by a wide diversity of population densities and land uses. By using a novel quantitative pyrolysis-GC/MS analysis for rubber polymer, we detected TRWP in 97% of the 149 sediment samples collected. The mean concentrations of TRWP were 4500 (n = 49; range = 62-11 600), 910 (n = 50; range = 50-4400) and 770 (n = 50; range = 26-4600) μg/g d.w. for the characterized portions of the Seine, Chesapeake and Yodo-Lake Biwa watersheds, respectively. A subset of samples from the watersheds (n = 45) was pooled to evaluate TRWP metals, grain size and organic carbon correlations by principal components analysis (PCA), which indicated that four components explain 90% of the variance. The PCA components appeared to correspond to (1) metal alloys possibly from brake wear (primarily Cu, Pb, Zn), (2) crustal minerals (primarily Al, V, Fe), (3) metals mediated by microbial immobilization (primarily Co, Mn, Fe with TOC), and (4) TRWP and other particulate deposition (primarily TRWP with grain size and TOC). This study should provide useful information for assessing potential aquatic effects related to tire service life.

Dynamics and Stability of Rolling Viscoelastic Tires

Energy Technology Data Exchange (ETDEWEB)

Potter, Trevor [Univ. of California, Berkeley, CA (United States)

2013-04-30

Current steady state rolling tire calculations often do not include treads because treads destroy the rotational symmetry of the tire. We describe two methodologies to compute time periodic solutions of a two-dimensional viscoelastic tire with treads: solving a minimization problem and solving a system of equations. We also expand on work by Oden and Lin on free spinning rolling elastic tires in which they disovered a hierachy of N-peak steady state standing wave solutions. In addition to discovering a two-dimensional hierarchy of standing wave solutions that includes their N-peak hiearchy, we consider the eects of viscoelasticity on the standing wave solutions. Finally, a commonplace model of viscoelasticity used in our numerical experiments led to non-physical elastic energy growth for large tire speeds. We show that a viscoelastic model of Govindjee and Reese remedies the problem.

Materials Approach to Fuel Efficient Tires

Energy Technology Data Exchange (ETDEWEB)

Votruba-Drzal, Peter [PPG Industries, Monroeville, PA (United States); Kornish, Brian [PPG Industries, Monroeville, PA (United States)

2015-06-30

The objective of this project was to design, develop, and demonstrate fuel efficient and safety regulation compliant tire filler and barrier coating technologies that will improve overall fuel efficiency by at least 2%. The program developed and validated two complementary approaches to improving fuel efficiency through tire improvements. The first technology was a modified silica-based product that is 15% lower in cost and/or enables a 10% improvement in tread wear while maintaining the already demonstrated minimum of 2% improvement in average fuel efficiency. The second technology was a barrier coating with reduced oxygen transmission rate compared to the state-of-the-art halobutyl rubber inner liners that will provide extended placarded tire pressure retention at significantly reduced material usage. A lower-permeance, thinner inner liner coating which retains tire pressure was expected to deliver the additional 2% reduction in fleet fuel consumption. From the 2006 Transportation Research Board Report1, a 10 percent reduction in rolling resistance can reduce consumer fuel expenditures by 1 to 2 percent for typical vehicles. This savings is equivalent to 6 to 12 gallons per year. A 1 psi drop in inflation pressure increases the tire's rolling resistance by about 1.4 percent.

Investigation of the Maximum Spin-Up Coefficients of Friction Obtained During Tests of a Landing Gear Having a Static-Load Rating of 20,000 Pounds

Science.gov (United States)

Batterson, Sidney A.

1959-01-01

An experimental investigation was made at the Langley landing loads track to obtain data on the maximum spin-up coefficients of friction developed by a landing gear having a static-load rating of 20,000 pounds. The forward speeds ranged from 0 to approximately 180 feet per second and the sinking speeds, from 2.7 feet per second to 9.4 feet per second. The results indicated the variation of the maximum spin-up coefficient of friction with forward speed and vertical load. Data obtained during this investigation are also compared with some results previously obtained for nonrolling tires to show the effect of forward speed.

Loading Effect on Tire Noise Radiation

OpenAIRE

Cao, Rui; Bolton, J Stuart

2016-01-01

Noise radiated by tires is a prominent noise pollution source and it is affected by many different parameters. Here, the effect of static load on tire noise radiation in a laboratory environment was investigated. The measurement was conducted by using the Tire Pavement Testing Apparatus (TPTA), on which a loaded tire can be run at speeds up to 50 km/hr; the tire noise was measured using a nearfield microphone method. The tire loading was varied from 500 to 900 pounds, and several different co...

Road dust from pavement wear and traction sanding

Energy Technology Data Exchange (ETDEWEB)

Kupiainen, K.

2007-07-01

Vehicles affect the concentrations of ambient airborne particles through exhaust emissions, but particles are also formed in the mechanical processes in the tire-road interface, brakes, and engine. Particles deposited on or in the vicinity of the road may be re-entrained, or resuspended, into air through vehicle-induced turbulence and shearing stress of the tires. A commonly used term for these particles is 'road dust'. The processes affecting road dust emissions are complex and currently not well known. Road dust has been acknowledged as a dominant source of PM10 especially during spring in the sub-arctic urban areas, e.g. in Scandinavia, Finland, North America and Japan. The high proportion of road dust in sub-arctic regions of the world has been linked to the snowy winter conditions that make it necessary to use traction control methods. Traction control methods include dispersion of traction sand, melting of ice with brine solutions, and equipping the tires with either metal studs (studded winter tires), snow chains, or special tire design (friction tires). Several of these methods enhance the formation of mineral particles from pavement wear and/or from traction sand that accumulate in the road environment during winter. When snow and ice melt and surfaces dry out, traffic-induced turbulence makes some of the particles airborne. A general aim of this study was to study processes and factors underlying and affecting the formation and emissions of road dust from paved road surfaces. Special emphasis was placed on studying particle formation and sources during tire road interaction, especially when different applications of traction control, namely traction sanding and/or winter tires were in use. Respirable particles with aerodynamic diameter below 10 micrometers (PM10) have been the main concern, but other size ranges and particle size distributions were also studied. The following specific research questions were addressed: (i) How do traction

Advantage of SBR/carbon black masterbatch for tire tread application

Energy Technology Data Exchange (ETDEWEB)

Sone, K.; Ishiguro, M.; Akimoto, H.; Ishida, M.

1992-04-01

The performance required of tire tread is becoming more severe and more various year by year, as social demands on tires have been changing. To improve wear resistance, driving safety and good drive feeling, new HP tires (high performance passenger car tires) are developed intensively. In addition, good fuel efficiency is required to satisfy the CAFE rule, which was proposed for a better global environment. To support this movement of the tire industry, material suppliers are making an effort to supply better materials. Mitsubishi Kasei has been improving the quality and production process of WMB, a SBR/carbon black master-batch produced by co-coagulation of SBR latex, carbon black and extender oil under the wet dispersion process. Compared to the tire tread made from dry-mixing compounds, that made from the WMB shows the following characteristics: (1) the abrasion resistance and the durability are higher; (2) from the viscoelastic properties, skid performance and driving stability are expected to be improved. These characteristics are remarkable when WMB is compounded in the recipes for HP and racing tires using fine carbon black. In this article, these features of WMB are studied from the view point of carbon black dispersion and polymer-carbon black interaction. Furthermore, the changes of carbon black structure during abrasion and fatigue process are analyzed and the mechanisms of these processes are discussed.

Occurrence of benzothiazole and its derivates in tire wear, road dust, and roadside soil.

Science.gov (United States)

Zhang, Jing; Zhang, Xinfeng; Wu, Lin; Wang, Ting; Zhao, Jingbo; Zhang, Yanjie; Men, Zhengyu; Mao, Hongjun

2018-06-01

Benzothiazole (BT) and its derivates are commonly used as vulcanization accelerators in rubber production. Information on the occurrence of BTs in road dust (RD) and on human exposure to these compounds is very limited. BT and its six derivates in tire wear particles (TWPs) and RD were determined in this study. Samples were extracted using solid-liquid extraction, purified by a HLB SPE column, and determined by ultra-high performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). All seven BTs were found in 17 TWPs samples from different tire brands. The mass fractions of all seven BTs (∑BTs) in TWPs ranged from 46.93 to 215 μg/g with an average concentration of 99.32 μg/g. Benzothiazole and 2-hydroxybenzothiazole (2-OH-BT) were the two major compounds, accounting for 56%-89% of the total. The seven BTs were also found in all 36 sets of RD samples (each set included one sample of TSP (particles < 75 μm in diameter), PM 10 (particles < 10 μm in diameter) and PM 2.5 (particles < 2.5 μm in diameter)) fractions of RD. The median ∑BTs concentration was highest in PM 2.5 (26.62 μg/g), followed by PM 10 (22.03 μg/g), and TSP (0.68 μg/g). Of the seven BTs, BT, 2-aminobenzothiazole (2-NH 2 -BT), 2-mercaptobenzothiazole (MBT), and 2-(methylthio)benzothiazole (MTBT) were distributed in PM 2.5 and 2-OH-BT was distributed in PM 2.5-10 of RD. Based on the mass fractions of BTs in the TSP, PM 10 , and PM 2.5 fractions of RD, human exposure via ingestion, inhalation and dermal absorption were evaluated. Ingestion was found to be the main exposure pathway in humans, and daily intake of BTs in PM 2.5 was highest, followed by PM 10 and TSP, respectively. Children may suffer more health risks than adults when exposed to RD. Copyright © 2018 Elsevier Ltd. All rights reserved.

Experimental Investigations on the Pull-Out Behavior of Tire Strips Reinforced Sands.

Science.gov (United States)

Li, Li-Hua; Chen, Yan-Jun; Ferreira, Pedro Miguel Vaz; Liu, Yong; Xiao, Heng-Lin

2017-06-27

Waste tires have excellent mechanical performance and have been used as reinforcing material in geotechnical engineering; however, their interface properties are poorly understood. To further our knowledge, this paper examines the pull-out characteristics of waste tire strips in a compacted sand, together with uniaxial and biaxial geogrids also tested under the same conditions. The analysis of the results shows that the interlocking effect and pull-out resistance between the tire strip and the sand is very strong and significantly higher than that of the geogrids. In the early stages of the pull-out test, the resistance is mainly provided by the front portion of the embedded tire strips, as the pull-out test continues, more and more of the areas towards the end of the tire strips are mobilized, showing a progressive failure mechanism. The deformations are proportional to the frictional resistance between the tire-sand interface, and increase as the normal stresses increase. Tire strips of different wear intensities were tested and presented different pull-out resistances; however, the pull-out resistance mobilization patterns were generally similar. The pull-out resistance values obtained show that rubber reinforcement can provide much higher pull-out forces than the geogrid reinforcements tested here, showing that waste tires are an excellent alternative as a reinforcing system, regardless of the environmental advantages.

Spin current evolution in the separated spin-up and spin-down quantum hydrodynamics

International Nuclear Information System (INIS)

Trukhanova, Mariya Iv.

2015-01-01

We have developed a method of quantum hydrodynamics (QHD) that describes particles with spin-up and with spin-down in separate. We have derived the equation of the spin current evolution as a part of the set of the quantum hydrodynamics equations that treat particles with different projection of spin on the preferable direction as two different species. We have studied orthogonal propagation of waves in the external magnetic field and determined the contribution of quantum corrections due to the Bohm potential and to magnetization energy of particles with different projections of spin in the spin-current wave dispersion. We have analyzed the limits of weak and strong magnetic fields. - Highlights: • We derive the spin current equation for particles with different projection of spin. • We predict the contribution of Bohm potential to the dynamics of spin current. • We derive the spin-current wave in the system of spin-polarized particles. • We study the propagation of spin-acoustic wave in magnetized dielectrics.

Eating a planet and spinning up

Science.gov (United States)

Qureshi, Ahmed; Naoz, Smadar; Shkolnik, Evgenya L.

2018-01-01

One of the predictions of high eccentricity planetary migration is that many planets will end up plunging into their host stars. We investigate the consequence of planetary mergers on their stellar hosts’ spin-period. Energy and angular momentum conservation yield that a planet consumption by a star will spin-up of the star. We find that our calculations align with the observed bifurcation in the stellar spin-period in young clusters. After a Sun-like star has eaten a planet, it will then, spin down due to magnetic braking, consistent with the observed lack of fast rotators in old clusters. The agreement between the calculations presented here and the observed spin-period of stars in young clusters provides circumstantial evidence that planetary accretion onto their host stars is a generic feature in planetary-system evolution.

Demonstration of improved vehicle fuel efficiency through innovative tire design, materials, and weight reduction technologies

Energy Technology Data Exchange (ETDEWEB)

Donley, Tim [Cooper Tire & Rubber Company Incorporated, Findlay, OH (United States)

2014-12-31

Cooper completed an investigation into new tire technology using a novel approach to develop and demonstrate a new class of fuel efficient tires using innovative materials technology and tire design concepts. The objective of this work was to develop a new class of fuel efficient tires, focused on the “replacement market” that would improve overall passenger vehicle fuel efficiency by 3% while lowering the overall tire weight by 20%. A further goal of this project was to accomplish the objectives while maintaining the traction and wear performance of the control tire. This program was designed to build on what has already been accomplished in the tire industry for rolling resistance based on the knowledge and general principles developed over the past decades. Cooper’s CS4 (Figure #1) premium broadline tire was chosen as the control tire for this program. For Cooper to achieve the goals of this project, the development of multiple technologies was necessary. Six technologies were chosen that are not currently being used in the tire industry at any significant level, but that showed excellent prospects in preliminary research. This development was divided into two phases. Phase I investigated six different technologies as individual components. Phase II then took a holistic approach by combining all the technologies that showed positive results during phase one development.

Tire Log™

OpenAIRE

ECT Team, Purdue

2013-01-01

The Tire Log™ is a patented innovation made from waste tires with a unique and energy efficient approach to recycling tires. Re-Tread Products (RTP) process takes full advantage of the embedded energy in tires that is wasted in conventional tire recycling that primarily involves the grinding, burying or burning of waste tires.

Development and applicability estimation of the tire contact pressure measurement system; Tire secchiatsukei no kaihatsu to oyosei hyoka

Energy Technology Data Exchange (ETDEWEB)

Mizutani, Y.; Amago, T.; Takahashi, T.; Sakuma, S.; Mori, N. [Toyota Central R and D Laboratories, Inc., Aichi (Japan); Nagae, A. [Toyota Motor Corp., Aichi (Japan); Yasuoka, M. [Toyo Tire and Rubber Co. Ltd., Osaka (Japan)

1995-04-20

A pressure sensor more reliable than the conventional types and a tire pressure measurement system using a plurality of sensors of the said reliable type have been developed. The sensor is an inverted T in shape, the upper surface of the vertical beam thereof receives the pressure, and the two ends of the horizontal beam are fixed. The load per unit area imposed on the pressure receiving surface is separated into three components, the X and Y components in the tangential direction are sensed by the vertical beam while the Z component in the vertical direction is sensed by a distortion gauge attached to the horizontal beam. For the measurement of the contact pressure distribution for the entire contact surface, a measuring device was developed, comprising a multiple point contact pressure gauge with 30 sensors of the reliable type discussed here embedded therein, a tire rolling tester, and a data processing unit. A tire wear estimation test was conducted using this pressure sensor and a contact probe type slip sensor, and it was found that a tire of a greater friction energy ratio is easier to experience abnormal abrasion and that the new pressure sensor is useful in estimating abnormal abrasion. Further, it was indicated that the present measuring device is applicable to the analysis of the mechanism wherein shaft force results from contact pressure on the soil. 3 refs., 11 figs., 3 tabs.

On the properties of nuclear matter with an excess of neutrons, spin-up neutrons and spin-up protons using effective nucleon-nucleon potential

International Nuclear Information System (INIS)

Hassan, M.Y.; Ramadan, S.

1978-01-01

The binding energy of nuclear matter with an excess of neutrons, with spin-up neutrons and spin-up protons (characterized by the corresponding parameters αsub(tau)=(N-Z)/A, αsub(n)=(N(up)-N(down))/A, and αsub(p)=(Z(up)-Z(down))/A) contains three symmetry energies: the isospin symmetry energy epsilon sub(tau), the spin symmetry energy epsilon sub(sigma) and the spin-isospin symmetry energy epsilon sub(sigma tau). These energies are calculated using velocity-dependent effective potential of s-wave interaction, which was developed by Dzhibuti and Mamasakhlisov. The spin, isospin and spin-isospin dependent parts of the single-particle potential in nuclear matter are also calculated using the same effective nucleon-nucleon potentials. The spin-spin part of the optical model potential is estimated. (author)

Marshall properties of asphalt concrete using crumb rubber modified of motorcycle tire waste

Science.gov (United States)

Siswanto, Henri; Supriyanto, Bambang; Pranoto, Chandra, Pria Rizky; Hakim, Arief Rahman

2017-09-01

The aim of this study is to explain the effect of Crumb Rubber Modified (CRM) of motorcycle tire waste on Marshall properties of asphalt mix. Two types of aggregate gradation, asphalt concrete wearing course (ACWC) and asphalt concrete base (ACB), and CRM passing #50 sieve size were used. Seven levels of CRM content were investigated in this study, namely 0%, 0.5%, 1%, 1.5%, 3%, 4.5%, and 6% by weight of aggregate. Marshall test is conducted on Marshall specimens. The specimens are tested in their optimum binder content (OBC). The results indicate that CRM addition of motorcycle tire waste increases the Marshall stability of the both mix, ACWC and ACB. In addition, 1% CRM addition of motorcycle tire waste of the total mix weight is the best mix.

Fundamental studies on dynamic wear behavior of SBR rubber compounds modified by SBR rubber powder

OpenAIRE

Euchler, Eric; Heinrich, Gert; Michael, Hannes; Gehde, Michael; Stocek, Radek; Kratina, Ondrej; Kipscholl, Reinhold; Bunzel, Jörg-Michael; Saal, Wolfgang

2016-01-01

The aim of this study is focused on the experimental investigation of dynamic wear behavior of carbon black filled rubber compounds comprising pristine styrene butadiene rubber (SBR) together with incorporated SBR ground rubber (rubber powder). We also analyzed and described quantitatively the service conditions of some dynamically loaded rubber products, which are liable to wear (e.g. conveyor belts, tires). Beside the well-known standard test method to characterize wear resistance at steady...

Tires

Science.gov (United States)

2015-12-15

measure heat from the casing. Tread surface temperature. Tread (surface) infrared temperature can be inconsistent since the measurements are...have any adverse effect on rubber products. b. Avoid areas that are wet, humid, oily, greasy, or in direct sunlight. Do not store tires in the...used, from sticking to the tire. Do not let soapstone accumulate in the tire. Inspect and clean the tire beads to remove corrosion or residual rubber

Episodic Spin-up and Spin-down Torque on Earth

Science.gov (United States)

Slabinski, Victor J.; Mendonca, Antonio A.

2018-04-01

Variations in Earth rotation angle are traditionally expressed by the time difference (ΔT=TT-UT1) between Terrestrial Time (TT) as told by atomic clocks and Universal Time UT1, the time variable used by the Earth-rotation formula. A plot of ΔT versus TT over the past 160 years shows a continuous curve with approximate straight-line segments with different spans of order ~20 years. Removing the tidal and seasonal variations from the data gives these line segments which represent the “decadal variations” in Earth rotation.The slope of a straight-line segment is proportional to the departure of Earth rotation rate from a reference value at the time. The change in slope over the relatively short time between segments indicates an episodic spin-up or spin-down in Earth rotation. The daily combination of VLBI, SLR, and other modern data available since 1973 gives us accurate, daily values of ΔT and the corresponding LOD (Length Of Day) values during these episodes. These allow us to determine the rotational acceleration occurring then.The three largest spin-speed changes found during the VLBI era have the following characteristics:Episode _____________ Duration__ ΔLOD__LOD Rate1983 Dec 30-1984 Jan 28 ... 29 d ...-0.65 ms ..-8.3 ms/y ..........spin-up1989 Mar 15-1989 May 23 ...69 d ....0.68 .......+3.6 ..............spin-down1994 Jan 21-2001 Apr 01 ... 6.5 y ...-2.2 .........-0.36 ..extended spin-upFor the first two episodes listed, we find the acceleration grows from zero (or at least a relatively small value) to its extreme value in ~1 day, stays approximately constant at this value for 29 or 69 days, and then decays back to zero over ~1 day. The acceleration, while it occurs, gives an LOD rate much greater than the 0.02 ms/y rate from tidal friction.The third episode shows that occasionally a several-year-long episode occurs. The acceleration magnitude is smaller but can make a larger total change in LOD (and spin rate). Tidal friction requires >100 y to equal

Haul truck tire dynamics due to tire condition

International Nuclear Information System (INIS)

Anzabi, R Vaghar; Nobes, D S; Lipsett, M G

2012-01-01

Pneumatic tires are costly components on large off-road haul trucks used in surface mining operations. Tires are prone to damage during operation, and these events can lead to injuries to personnel, loss of equipment, and reduced productivity. Damage rates have significant variability, due to operating conditions and a range of tire fault modes. Currently, monitoring of tire condition is done by physical inspection; and the mean time between inspections is often longer than the mean time between incipient failure and functional failure of the tire. Options for new condition monitoring methods include off-board thermal imaging and camera-based optical methods for detecting abnormal deformation and surface features, as well as on-board sensors to detect tire faults during vehicle operation. Physics-based modeling of tire dynamics can provide a good understanding of the tire behavior, and give insight into observability requirements for improved monitoring systems. This paper describes a model to simulate the dynamics of haul truck tires when a fault is present to determine the effects of physical parameter changes that relate to faults. To simulate the dynamics, a lumped mass 'quarter-vehicle' model has been used to determine the response of the system to a road profile when a failure changes the original properties of the tire. The result is a model of tire vertical displacement that can be used to detect a fault, which will be tested under field conditions in time-varying conditions.

Haul truck tire dynamics due to tire condition

Science.gov (United States)

Vaghar Anzabi, R.; Nobes, D. S.; Lipsett, M. G.

2012-05-01

Pneumatic tires are costly components on large off-road haul trucks used in surface mining operations. Tires are prone to damage during operation, and these events can lead to injuries to personnel, loss of equipment, and reduced productivity. Damage rates have significant variability, due to operating conditions and a range of tire fault modes. Currently, monitoring of tire condition is done by physical inspection; and the mean time between inspections is often longer than the mean time between incipient failure and functional failure of the tire. Options for new condition monitoring methods include off-board thermal imaging and camera-based optical methods for detecting abnormal deformation and surface features, as well as on-board sensors to detect tire faults during vehicle operation. Physics-based modeling of tire dynamics can provide a good understanding of the tire behavior, and give insight into observability requirements for improved monitoring systems. This paper describes a model to simulate the dynamics of haul truck tires when a fault is present to determine the effects of physical parameter changes that relate to faults. To simulate the dynamics, a lumped mass 'quarter-vehicle' model has been used to determine the response of the system to a road profile when a failure changes the original properties of the tire. The result is a model of tire vertical displacement that can be used to detect a fault, which will be tested under field conditions in time-varying conditions.

Spring Tire

Science.gov (United States)

Asnani, Vivake M.; Benzing, Jim; Kish, Jim C.

2011-01-01

The spring tire is made from helical springs, requires no air or rubber, and consumes nearly zero energy. The tire design provides greater traction in sandy and/or rocky soil, can operate in microgravity and under harsh conditions (vastly varying temperatures), and is non-pneumatic. Like any tire, the spring tire is approximately a toroidal-shaped object intended to be mounted on a transportation wheel. Its basic function is also similar to a traditional tire, in that the spring tire contours to the surface on which it is driven to facilitate traction, and to reduce the transmission of vibration to the vehicle. The essential difference between other tires and the spring tire is the use of helical springs to support and/or distribute load. They are coiled wires that deform elastically under load with little energy loss.

Wear of rolling element bearings in sodium

International Nuclear Information System (INIS)

Campbell, C.S.

1976-01-01

Rolling element bearings and related mechanisms are attractive for service in liquid sodium but it is not clear what minimum wear rate can be anticipated. For axially loaded angular contact bearings rotation is incompatible with pure rolling on both races and wear arises from the resulting ball spin. The initial pressure distributions and sizes of the contact ellipses can be calculated but will change with bearing wear. However, the most effective distribution for producing wear would be for the full loads to be borne on the tips of the contact areas, whose maximum length is given by examination of the race wear tracks. A calculation on such a basis should set a lower limit for the wear coefficient. Both the torque and instantaneous wear rate of a bearing will be similar functions of the integral over the contact areas of the product of contact pressure and radius from the ball spin axis. A better estimate of wear coefficient should be obtained by relating the average torque, the average wear, the initial torque and the initial wear where the conditions are known. Analysis of tests in sodium at 400 0 C of high speed steel and Stellite bearings by these methods indicates specific wear rates of the order of 10 -15 m 3 /N-m, not unduly out of line with the range of values found in conventional sliding tests

Simple Models for the Dynamic Modeling of Rotating Tires

Directory of Open Access Journals (Sweden)

J.C. Delamotte

2008-01-01

Full Text Available Large Finite Element (FE models of tires are currently used to predict low frequency behavior and to obtain dynamic model coefficients used in multi-body models for riding and comfort. However, to predict higher frequency behavior, which may explain irregular wear, critical rotating speeds and noise radiation, FE models are not practical. Detailed FE models are not adequate for optimization and uncertainty predictions either, as in such applications the dynamic solution must be computed a number of times. Therefore, there is a need for simpler models that can capture the physics of the tire and be used to compute the dynamic response with a low computational cost. In this paper, the spectral (or continuous element approach is used to derive such a model. A circular beam spectral element that takes into account the string effect is derived, and a method to simulate the response to a rotating force is implemented in the frequency domain. The behavior of a circular ring under different internal pressures is investigated using modal and frequency/wavenumber representations. Experimental results obtained with a real untreaded truck tire are presented and qualitatively compared with the simple model predictions with good agreement. No attempt is made to obtain equivalent parameters for the simple model from the real tire results. On the other hand, the simple model fails to represent the correct variation of the quotient of the natural frequency by the number of circumferential wavelengths with the mode count. Nevertheless, some important features of the real tire dynamic behavior, such as the generation of standing waves and part of the frequency/wavenumber behavior, can be investigated using the proposed simplified model.

A novel wireless piezoelectric tire sensor for the estimation of slip angle

International Nuclear Information System (INIS)

Erdogan, G; Alexander, L; Rajamani, R

2010-01-01

This paper introduces a simple approach for the analysis of tire deformation and proposes a new piezoelectric tire sensor for physically meaningful measurements of tire deformations. Tire deformation measurements in the contact patch can be used for the estimation of slip angle, tire forces, slip ratio and tire–road friction coefficient. The specific case of a wireless tire deformation sensor for the estimation of slip angle is taken up in this paper. A sensor in which lateral sidewall deformation can be decoupled from radial deformation is designed. The slope of the lateral deflection curve in the contact patch is used to calculate slip angle. A specially constructed tire test rig is used to experimentally evaluate the performance of the developed sensor. Results show that the developed sensor can accurately estimate slip angles up to values of 5°

A Novel Strain-Based Method to Estimate Tire Conditions Using Fuzzy Logic for Intelligent Tires

Directory of Open Access Journals (Sweden)

Daniel Garcia-Pozuelo

2017-02-01

Full Text Available The so-called intelligent tires are one of the most promising research fields for automotive engineers. These tires are equipped with sensors which provide information about vehicle dynamics. Up to now, the commercial intelligent tires only provide information about inflation pressure and their contribution to stability control systems is currently very limited. Nowadays one of the major problems for intelligent tire development is how to embed feasible and low cost sensors to obtain reliable information such as inflation pressure, vertical load or rolling speed. These parameters provide key information for vehicle dynamics characterization. In this paper, we propose a novel algorithm based on fuzzy logic to estimate the mentioned parameters by means of a single strain-based system. Experimental tests have been carried out in order to prove the suitability and durability of the proposed on-board strain sensor system, as well as its low cost advantages, and the accuracy of the obtained estimations by means of fuzzy logic.

The prediction of airborne and structure-borne noise potential for a tire

Science.gov (United States)

Sakamoto, Nicholas Y.

Tire/pavement interaction noise is a major component of both exterior pass-by noise and vehicle interior noise. The current testing methods for ranking tires from loud to quiet require expensive equipment, multiple tires, and/or long experimental set-up and run times. If a laboratory based off-vehicle test could be used to identify the airborne and structure-borne potential of a tire from its dynamic characteristics, a relative ranking of a large group of tires could be performed at relatively modest expense. This would provide a smaller sample set of tires for follow-up testing and thus save expense for automobile OEMs. The focus of this research was identifying key noise features from a tire/pavement experiment. These results were compared against a stationary tire test in which the natural response of the tire to a forced input was measured. Since speed was identified as having some effect on the noise, an input function was also developed to allow the tires to be ranked at an appropriate speed. A relative noise model was used on a second sample set of tires to verify if the ranking could be used against interior vehicle measurements. While overall level analysis of the specified spectrum had mixed success, important noise generating features were identified, and the methods used could be improved to develop a standard off-vehicle test to predict a tire's noise potential.

On the properties of nuclear matter with an excess of neutrons, of spin-up neutrons and of spin-up protons using the Skyrme interaction

International Nuclear Information System (INIS)

Hassan, M.Y.M.; Ramadan, S.

1983-11-01

The binding energy of nuclear matter with an excess of neutrons, of spin-up neutrons, and of spin-up protons (characterized by the corresponding parameters, αsub(tau)=(N-Z/A), αsub(n)=(Nup-Ndown)/A, and αsub(rho)=(Zup-Zdown)/A), contains three symmetry energies: the isospin symmetry energy Esub(tau), the spin symmetry energy Esub(σ), and spin-isospin symmetry energy Esub(σtau). General expressions for Esub(σ), Esub(tau) and Esub(σtau) are given in the case of the Skyrme interaction. These values are compared with previous results obtained by Dabrowski and Haensel (DH) with Brueckner-Gammel-Thaler, the Hamada-Johnston, and the Reid soft core nucleon-nucleon potentials. The spin, isospin and spin-isospin dependent parts of the single-particle potential in nuclear matter are also calculated using the Skyrme interaction. The spin, isospin and spin-isospin incompressibility are calculated using the Skyrme interaction. The spin-spin part of the optical model potential is estimated. The results are compared with those of Dabrowski and Haensel (DH) and Hassan and Ramadan. (author)

Energy requirements of tire pulling.

Science.gov (United States)

Fredriksen, Per M; Mamen, Asgeir

2017-10-01

We have investigated the effect using walking poles and pulling tires at 4 and 6 km·h-1 (1.11 and 1.67 m·s-1) speeds on oxygen uptake (V̇O2) and heart rate. Eleven subjects, 6 males, with a mean (SD) age of 25.2 (6.9) years participated in field tests involving walking without poles, walking with poles and tire pulling with poles. Increasing the load caused the largest increases in energy demand, more than 4 MET. Speed increase also caused substantial energy increase, approximately 4 MET. Increasing the inclination only modestly increased the oxygen uptake, approximately 2 MET. In both level walking and uphill walking, using poles marginally increased oxygen uptake compared to working without poles. Pulling one tire (12.5 kg) required an oxygen uptake of 27 (4) mL·kg-1·min-1 at 4 km·h-1 and 0% inclination. Adding one more tire (6 kg) drove the oxygen uptake further up to 39 (4) mL·kg-1·min-1. This is close to the requirement of level running at 10.5 km·h-1. Pulling both tires at 6 km·h-1 and 5% inclination required a V̇O2 of 54 (6) mL·kg-1·min-1, equal to running uphill at 5% inclination and 12.5 km·h-1 speed. Heart rate rose comparably with oxygen uptake. At 4 km·h-1 and 0% inclination the increase was 29 bpm, from 134 (21) to 163 (22) bpm when going from pulling one tire to two tires. In the hardest exercise, 6 km·h-1 and 5% inclination, heart rate reached 174 (14) bpm. The study showed that tire pulling even at slow speeds has an energy requirement that is so large that the activity may be feasible as endurance training.

The prediction of airborne and structure-borne noise potential for a tire

OpenAIRE

Sakamoto, Nicholas

2014-01-01

Tire/pavement interaction noise is a major component of both exterior pass-by noise and vehicle interior noise. The current testing methods for ranking tires from loud to quiet require expensive equipment, multiple tires, and/or long experimental set-up and run times. If a laboratory based off-vehicle test could be used to identify the airborne and structure-borne potential of a tire from its dynamic characteristics, a relative ranking of a large group of tires could be performed at relativel...

Full-scale aicraft tire pressure tests

OpenAIRE

FABRE, C; BALAY, Jean Maurice; LERAT, P; MAZARS, A

2009-01-01

This paper describes an outdoor full-scale test planned to improve experimental and theoretical knowledge related to the effects of aircraft internal tire inflation pressure on the behavior and damage of flexible pavement. Since modern aircraft can have tire pressures greater than 15 bar, the tests focus on pressures from 15 to 17.5 bar. The experimental pavement located on the Toulouse-Blagnac airport in France will include up to seven al different test sections, representative of current ai...

The effects of porosity in friction performance of brake pad using waste tire dust

Directory of Open Access Journals (Sweden)

İbrahim Mutlu

2015-10-01

Full Text Available Abstract This research is focused on the effect of porosity on the friction-wear properties of automotive brake pads. Waste Tire Dust (WTD was used as a new friction material in brake pads. Newly formulated brake pad materials with five different components have been produced by conventional techniques. In the experimental studies, the change of the friction coefficient, the temperature of the friction surface, the specific wear rate, and the hardness, density and porosity were measured. In addition, the micro-structural characterizations of brake pads are determined using Scanning Electron Microscopy (SEM. The mean coefficient of friction, porosity and specific wear are increased due to a WTD rate increases, on the other hand, hardness and density are decreased. As a result, WTD can be considered as an alternative to revalorize this kind of waste products in the brake pads and the amount of porosity of the brake pad affected the friction coefficient and wear behavior of the pad.

Full-scale aircraft tire pressure tests

OpenAIRE

FABRE, C; BALAY, Jean Maurice; LERAT, P; MAZARS, A

2009-01-01

This paper describes an outdoor full-scale test planned to improve experimental and theoretical knowledge related to the effects of aircraft internal tire inflation pressure on the behavior and damage of flexible pavement. Since modern aircraft can have tire pressures greater than 15 bar, the tests will focus on pressures from 15 bar to 17.5 bar. The experimental pavement located on the Toulouse-Blagnac airport in France will include up to seven al different test sections, representative of c...

Tire

Science.gov (United States)

Benzing, II, James Alfred (Inventor); Kish, James Christopher (Inventor); Asnani, Vivake Manohar (Inventor)

2012-01-01

A tire includes a plurality of helical springs. Each helical spring includes a first end portion, a second end portion, and an arching middle portion. Each helical spring is interlaced with at least one other helical spring thereby forming a laced toroidal structure extending about an entire circumference of the tire.

49 CFR 574.7 - Information requirements-new tire manufacturers, new tire brand name owners.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Information requirements-new tire manufacturers, new tire brand name owners. 574.7 Section 574.7 Transportation Other Regulations Relating to..., new tire brand name owners. (a)(1) Each new tire manufacturer and each new tire brand name owner...

Effect of Friction Model and Tire Maneuvering on Tire-Pavement Contact Stress

Directory of Open Access Journals (Sweden)

Haichao Zhou

2015-01-01

Full Text Available This paper aims to simulate the effects of different friction models on tire braking. A truck radial tire (295/80R22.5 was modeled and the model was validated with tire deflection. An exponential decay friction model that considers the effect of sliding velocity on friction coefficients was adopted for analyzing braking performance. The result shows that the exponential decay friction model used for evaluating braking ability meets design requirements of antilock braking system (ABS. The tire-pavement contact stress characteristics at various driving conditions (static, free rolling, braking, camber, and cornering were analyzed. It is found that the change of driving conditions has direct influence on tire-pavement contact stress distribution. The results provide the guidance for tire braking performance evaluation.

Improvement of wheel skidder tractive performance by tire inflation pressure and tire chains

OpenAIRE

Stoilov, Stanimir

2007-01-01

The motion resistance ratio, gross traction ratio and net traction ratio of a wheel cable skidder were determined and mathematical models derived for three tire inflation pressure values with or without tire chains on forest road in mountainous conditions. The motion resistance ratio increases with the increase of tire inflation pressure. On the contrary, the gross traction ratio increases with the decrease of tire inflation pressure. However, when the tires are equipped with tire chains t...

Tire Recycling

Science.gov (United States)

1997-01-01

Cryopolymers, Inc. tapped NASA expertise to improve a process for recycling vehicle tires by converting shredded rubber into products that can be used in asphalt road beds, new tires, hoses, and other products. In conjunction with the Southern Technology Applications Center and Stennis Space Center, NASA expertise in cryogenic fuel-handling needed for launch vehicle and spacecraft operations was called upon to improve the recycling concept. Stennis advised Cryopolymers on the type of equipment required, as well as steps to reduce the amount of liquid nitrogen used in the process. They also guided the company to use more efficient ways to control system hardware. It is estimated that more than 300 million tires nationwide are produced per year. Cryopolymers expects to reach a production rate of 5,000 tires recycled per day.

Long-term clinical results: 3 years of up to 30-night continuous wear of lotrafilcon A silicone hydrogel and daily wear of low-Dk/t hydrogel lenses.

Science.gov (United States)

Bergenske, Peter; Long, Bill; Dillehay, Sally; Barr, Joseph T; Donshik, Peter; Secor, Glenda; Yoakum, John; Chalmers, Robin L

2007-03-01

To summarize results of a 3-year clinical trial assessing subjective and objective experience with lotrafilcon A silicone hydrogel (SH) lenses for up to 30 nights of continuous wear or low-Dk/t daily-wear (LDW) hydrogel lenses. Nineteen sites dispensed SH lenses to 317 subjects (286 current wearers and 31 new wearers) and 2-week replacement LDW lenses to 81 new wearers in a 3-year study. For the SH cohort, limbal redness, conjunctival redness, and corneal neovascularization improved among 23%, 21%, and 13% of eyes, respectively (PDk/t hydrogel lenses. Many biomicroscopy signs and symptoms worsened among neophytes wearing daily-wear low-Dk/t hydrogel lenses. The use of lotrafilcon A lenses may minimize many ocular changes from soft contact lens wear.

No immediate relief for large mining tire shortage

Energy Technology Data Exchange (ETDEWEB)

Fiscor, S.

2006-05-15

Inventories are low and they will not get better anytime soon, but mine operators do have a few options. The three main manufacturers supplying tires to the US mining industry, Bridgestone Firestone Off Road Tire Company, Goodyear and Michelin are struggling to keep up with demand, but are unlikely to restore inventories to manageable levels by 2009. Meanwhile Yokohama and Global Tyres have stepped in to help. The article reports plans for expansions to plant in Japan. In the meantime, mine operators need to plan accordingly and pay increased attention to tire maintenance. The larger the tyre, the less available it is. 3 photos.

Microwave Absorption Characteristics of Tire

Science.gov (United States)

Zhang, Yuzhe; Hwang, Jiann-Yang; Peng, Zhiwei; Andriese, Matthew; Li, Bowen; Huang, Xiaodi; Wang, Xinli

The recycling of waste tires has been a big environmental problem. About 280 million waste tires are produced annually in the United States and more than 2 billion tires are stockpiled, which cause fire hazards and health issues. Tire rubbers are insoluble elastic high polymer materials. They are not biodegradable and may take hundreds of years to decompose in the natural environment. Microwave irradiation can be a thermal processing method for the decomposition of tire rubbers. In this study, the microwave absorption properties of waste tire at various temperatures are characterized to determine the conditions favorable for the microwave heating of waste tires.

Directions for material recovery of used tires and their use in the production of new products intended for the industry of civil construction and pavements

Science.gov (United States)

Bulei, C.; Todor, M. P.; Heput, T.; Kiss, I.

2018-01-01

The management of waste from used tires is one of the major principles of recycling and reuse, which involves encouraging a high level of material recovery components, preferably by recycling. Given the current pressure on natural resources on a global scale we must fully take into account the waste in a broader framework defined by the flow of raw materials and their sustainable use. Thus, the opportunity to use various waste from used tires as raw material in order to support economic activities becomes a priority. The recycling of raw materials from waste products and their use in new production processes for their material capitalization is becoming a sustainable approach. Used tire recycling, is the process of recycling waste tires that are no longer suitable for use on vehicles due to wear or irreparable damage. These tires are a problematic source of waste, due to the large volume produced, the durability of the tires, and the components in the tire that are ecologically problematic. Although tires are usually burnt, not recycled, efforts are continuing to find value. Tires can be recycled into, among other things, typically as crumb rubber modifier in recycled pavement. The paper presents aspects of the product resulting from crushing of used tires (powder), which can be used properly valued in the street furniture field or building materials containing rubber.

NUMERICAL MODELLING AND EXPERIMENTAL INFLATION VALIDATION OF A BIAS TWO-WHEEL TIRE

Directory of Open Access Journals (Sweden)

CHUNG KET THEIN

2016-02-01

Full Text Available This paper presents a parametric study on the development of a computational model for bias two-wheel tire through finite element analysis (FEA. An 80/90- 17 bias two-wheel tire was adopted which made up of four major layers of rubber compound with different material properties to strengthen the structure. Mooney-Rivlin hyperelastic model was applied to represent the behaviour of incompressible rubber compound. A 3D tire model was built for structural static finite element analysis. The result was validated from the inflation analysis. Structural static finite element analysis method is suitable for evaluation of the tire design and improvement of the tire behaviour to desired performance. Experimental tire was inflated at various pressures and the geometry between numerical and experimental tire were compared. There are good agreements between numerical simulation model and the experiment results. This indicates that the simulation model can be applied to the bias two-wheel tire design in order to predict the tire behaviour and improve its mechanical characteristics.

Post-consumer tires back into new tires: de-vulcanization and re-utilization of passenger car tires

OpenAIRE

Saiwari, Sitisaiyidah

2013-01-01

Enabling recycling loops for used passenger car tires is a challenge and an opportunity. The challenge lies in the presence of SBR as the main elastomer in this type of tires, which makes this material difficult to reclaim due to the tendency of the elastomer chain fragments to re-combine. The opportunity lies in the wide availability of the material and in the fact that passenger car tires form a huge potential market for recycled rubber. The aim of this study is to develop a de-vulcanizatio...

Slip Control of Electric Vehicle Based on Tire-Road Friction Coefficient Estimation

Directory of Open Access Journals (Sweden)

Gaojian Cui

2017-01-01

Full Text Available The real-time change of tire-road friction coefficient is one of the important factors that influence vehicle safety performance. Besides, the vehicle wheels’ locking up has become an important issue. In order to solve these problems, this paper comes up with a novel slip control of electric vehicle (EV based on tire-road friction coefficient estimation. First and foremost, a novel method is proposed to estimate the tire-road friction coefficient, and then the reference slip ratio is determined based on the estimation results. Finally, with the reference slip ratio, a slip control based on model predictive control (MPC is designed to prevent the vehicle wheels from locking up. In this regard, the proposed controller guarantees the optimal braking torque on each wheel by individually controlling the slip ratio of each tire within the stable zone. Theoretical analyses and simulation show that the proposed controller is effective for better braking performance.

High Value Scrap Tire Recycle

Energy Technology Data Exchange (ETDEWEB)

Bauman, B. D.

2003-02-01

The objectives of this project were to further develop and scale-up a novel technology for reuse of scrap tire rubber, to identify and develop end uses for the technology (products), and to characterize the technology's energy savings and environmental impact.

Tire inspection machine presenting an X-ray image of the entire width of the tire

International Nuclear Information System (INIS)

1975-01-01

An X-ray machine for production line inspection of tires places each tire in turn with one sector of the tire inside of a U-shaped arrangement of three fluorescent screens so that one screen faces the tread and the other two face the sides of the tire. An X-ray source inside the bead circle of the tire produces X-ray shadow pictures on the screens, which are separately viewed by a video camera, with an image of the picture on each screen transferred to a third of the target of a storage tube, so that a composite image of the entire width of the tire sector can be displayed on a picture tube. The tire is rotated step-wise for display of still pictures of every sector of the tire. (Auth.)

Tire-road noise: an experimental study of tire and road design parameters

OpenAIRE

Bekke, Dirk; Wijnant, Ysbrand H.; Weegerink, Thijs; de Boer, Andries

2013-01-01

It is widely known that road traffic noise has negative influences on human health. Hence, as tire-road noise is considered to be the most dominant cause of road traffic noise above 30-50 km/h, a lot of research is performed by the two involving industries: road authorities/manufacturers and tire manufacturers. Usually, the parameters influencing exterior tire-road noise are often examined separately, whereas it is the tire-road interaction which obviously causes the actual noise. An integral...

Tire safety : everything rides on it

Science.gov (United States)

2008-01-01

This booklet presents a comprehensive overview of tire safety, including information on the following topics: basic tire maintenance; Uniform Tire Quality Grading System; fundamental characteristics of tires; and tire safety tips.

Effect of wheelchair mass, tire type and tire pressure on physical strain and wheelchair propulsion technique.

Science.gov (United States)

de Groot, Sonja; Vegter, Riemer J K; van der Woude, Lucas H V

2013-10-01

The purpose of this study was to evaluate the effect of wheelchair mass, solid vs. pneumatic tires and tire pressure on physical strain and wheelchair propulsion technique. 11 Able-bodied participants performed 14 submaximal exercise blocks on a treadmill with a fixed speed (1.11 m/s) within 3 weeks to determine the effect of tire pressure (100%, 75%, 50%, 25% of the recommended value), wheelchair mass (0 kg, 5 kg, or 10 kg extra) and tire type (pneumatic vs. solid). All test conditions (except pneumatic vs. solid) were performed with and without instrumented measurement wheels. Outcome measures were power output (PO), physical strain (heart rate (HR), oxygen uptake (VO2), gross mechanical efficiency (ME)) and propulsion technique (timing, force application). At 25% tire pressure PO and subsequently VO2 were higher compared to 100% tire pressure. Furthermore, a higher tire pressure led to a longer cycle time and contact angle and subsequently lower push frequency. Extra mass did not lead to an increase in PO, physical strain or propulsion technique. Solid tires led to a higher PO and physical strain. The solid tire effect was amplified by increased mass (tire × mass interaction). In contrast to extra mass, tire pressure and tire type have an effect on PO, physical strain or propulsion technique of steady-state wheelchair propulsion. As expected, it is important to optimize tire pressure and tire type. Copyright © 2013 IPEM. Published by Elsevier Ltd. All rights reserved.

76 FR 28502 - Cooper Tire & Rubber Tire Company, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2011-05-17

...-0054; Notice 1] Cooper Tire & Rubber Tire Company, Receipt of Petition for Decision of Inconsequential Noncompliance Cooper Tire & Rubber Tire Company, (Cooper),\\1\\ has determined that approximately 6,964 passenger car replacement tires manufactured between January 23, 2011 and March 26, 2011, do not fully comply...

Analysis of automotive tire construction. Jidosha tire no kozo kaiseki

Energy Technology Data Exchange (ETDEWEB)

Ishihara, K. (Toyo Tire and Rubber Co. Ltd., Osaka (Japan))

1993-06-15

This paper introduces features and trends of analyzing performance and construction of automotive tires. Tires are demanded of high durability, high motion performance, good comfort performance for vibration and noise, and low fuel consumption performance. A feature of analyzing the construction is to execute a modelling assuming that a tire has air-rigid flexible structure and rubber materials show hyperelastic behavior, hypothesizing a strain energy density function. In addition, a tire is highly incompressible. Visco elasticity and anti-friction performance are also important points. Rubber and cord layers have elastic characteristic of three-dimensional perpendicular anisotropy as well as non-linearity with which characteristics change according to transformation. A structural analysis must cover from static analysis to steady dynamic analysis, non-steady dynamic analysis, and eigenvalue analysis. Thermal analysis of tires simulates phenomena by combining dynamical analysis with thermal analysis. Super-computers have now come to be used for formulating equilibrium equations using finite element methods, developing finite elements, and performing heat or visco elasticity analysis and applied analysis. 35 refs., 3 figs.

Research and application of online measurement system of tire tread profile in automobile tire production

Science.gov (United States)

Wang, Pengyao; Chen, Xiangguang; Yang, Kai; Liu, Xuejiao

2017-01-01

To improve the measuring efficiency of width and thickness of tire tread in the process of automobile tire production, the actual condition for the tire production process is analyzed, and a fast online measurement system based on moving tire tread of tire specifications is established in this paper. The coordinate data of tire tread profile is acquired by 3D laser sensor, and we use C# language for programming which is an object-oriented programming language to complete the development of client program. The system with laser sensor can provide real-time display of tire tread profile and the data to require in the process of tire production. Experimental results demonstrate that the measuring precision of the system is <= 1mm, it can meet the measurement requirements of the production process, and the system has the characteristics of convenient installation and testing, system stable operation.

Stereo Vision Inside Tire

Science.gov (United States)

2015-08-21

1 Stereo Vision Inside Tire P.S. Els C.M. Becker University of Pretoria W911NF-14-1-0590 Final...Stereo Vision Inside Tire 5a. CONTRACT NUMBER W911NF-14-1-0590 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Prof PS Els CM...on the development of a stereo vision system that can be mounted inside a rolling tire , known as T2-CAM for Tire -Terrain CAMera. The T2-CAM system

EVALUATION OF TIRE RUBBER DISPOSAL IN CONCRETE FOR PAVEMENTS

Directory of Open Access Journals (Sweden)

Rosa Cristina Cecche Lintz

2009-01-01

Full Text Available The production of waste by the tire industry has been a growing problem, indicating the need for its reuse. More than thirty million tires are discharged per year in Brazil, where regulation for the environment states that for each four new tires, five unusable ones must be adequately disposed by manufacturers and importers. Paving consumes an extremely large quantity of materials, which can be the source of rational application of waste and rejected materials. Research shows that tire rubber can be added to asphalt, which increases its durability and improves pavement quality and safety conditions by absorbing the rubber elastic properties, and also be used for architectural applications, among others. This study deals with the addition of rubber fibers from tire crushing in concrete for roadway pavements in order to provide proper indication about the alternative material disposal through an evaluation of the mechanical behavior of the modified concrete. Different concrete mixes were produced, within which, part of fine aggregates were substituted by tire rubber and mechanical experiment tests were performed, which show that, due to great resistance losses, the disposal of this alternative material in concrete should be considered for light traffic pavements, with the addition of rubber ranging up to 10% in mass.

EVALUATION OF TIRE RUBBER DISPOSAL IN CONCRETE FOR PAVEMENTS

Directory of Open Access Journals (Sweden)

Rosa Cristina Cecche Lintz

2009-12-01

Full Text Available The production of waste by the tire industry has been a growing problem, indicating the need for its reuse. More than thirty million tires are discharged per year in Brazil, where regulation for the environment states that for each four new tires, five unusable ones must be adequately disposed by manufacturers and importers. Paving consumes an extremely large quantity of materials, which can be the source of rational application of waste and rejected materials. Research shows that tire rubber can be added to asphalt, which increases its durability and improves pavement quality and safety conditions by absorbing the rubber elastic properties, and also be used for architectural applications, among others. This study deals with the addition of rubber fibers from tire crushing in concrete for roadway pavements in order to provide proper indication about the alternative material disposal through an evaluation of the mechanical behavior of the modified concrete. Different concrete mixes were produced, within which, part of fine aggregates were substituted by tire rubber and mechanical experiment tests were performed, which show that, due to great resistance losses, the disposal of this alternative material in concrete should be considered for light traffic pavements, with the addition of rubber ranging up to 10% in mass.

Wheels and Tires: Understanding the Numbers on the Sides of Tires Might Lead to Longer Life Tires and Improved Driving Safety

Science.gov (United States)

Ritz, John M.

2005-01-01

Automotive wheels and tires require knowledge to understand their specifications and use. While the durability and useful life of tires have increased substantially over the last several decades, in all probability consumers will purchase a number of vehicle tires over their lifetime. Knowing how they are made and what the numbers mean will assist…

Post-consumer tires back into new tires: de-vulcanization and re-utilization of passenger car tires

NARCIS (Netherlands)

Saiwari, Sitisaiyidah

2013-01-01

Enabling recycling loops for used passenger car tires is a challenge and an opportunity. The challenge lies in the presence of SBR as the main elastomer in this type of tires, which makes this material difficult to reclaim due to the tendency of the elastomer chain fragments to re-combine. The

Method and apparatus for inspecting tires

International Nuclear Information System (INIS)

Fox, R.L.T.

1975-01-01

A method and apparatus for inspecting tires by the use of x-rays is disclosed in which a tire is advanced to an inspection station, engaged along opposite bead rims and inflated to axially spread the bead rims and side walls. An x-ray source is advanced axially into the tire and the tire is eccentrically rotated relative to the x-ray source to enable radial positioning of the source relative to the tire near the tire bead rim diameter without requiring radial movement of the x-ray source. The x-ray source produces an x-ray beam which sweeps about the interior of the expanded tire from bead rim to bead rim while the tire is rotated about its centerline. An x-ray detection system detects x-rays which have penetrated the wall and produces inspection information concerning the tire construction. (Patent Office Record)

Nonlinear spin-up in a circular cylinder

NARCIS (Netherlands)

van de Konijnenberg, J.A.; Heijst, van G.J.F.

1995-01-01

Nonlinear spin-up in a circular cylindrical tank is investigated experimentally and compared with the Wedemeyer model. The experiments were performed with water, using tracer particles floating at the free surface in order to visualize the flow field. The experimentally determined vorticity profiles

Tire-soil interaction model for turning (steered) tires

Science.gov (United States)

Karafiath, L. L.

1985-07-01

A review of the experimental information on the development of lateral forces on tires traveling at an angle to their center plane is presented and the usefulness of the consideration of the lateral forces for the development of an analytical model is evaluated. Major components of the lateral force have been identified as the forces required to balance the tractive force and the drawbar pull vectorially. These are the shear stresses developing in the contact area and the horizontal component of the normal stresses acting on the in-ground portion or the curved side walls of the tire. The tire-soil interaction model for steady state straight travel has been expanded to include the necessary algorithms for the calculation of these lateral forces. The pattern of tractive force-slip and longitudinal-lateral force relationships is in general agreement with experiments.

The Use of Deconstructed Tires as Elastic Elements in Railway Tracks.

Science.gov (United States)

Sol-Sánchez, Miguel; Moreno-Navarro, Fernando; Rubio-Gámez, Mª Carmen

2014-08-18

Elastic elements such as rail pads, under sleeper pads and under ballast mats are railway components that allow for a reduction in track deterioration and vibrations. And they are furthermore commonly used to obtain an optimal vertical stiffness of the infrastructure. However, the use of elastomeric materials can increase construction costs and the consumption of raw materials. Thus, the utilization of used tire layers offers an alternative to reuse an abundant waste reducing the cost of elastic elements. In addition, an innovator technique allows deconstructing tire layers without grinding up the material, reducing production costs at the same time that tire properties are remained. This research is focused on the study of the viability of developing elastic components from used tire layers by evaluating the influence of thickness, the resistance capacity of the elements and their behavior in a ballast box. Results indicate the ability of tire pads to manufacture elastic elements (rail pads, under sleeper pads and under ballast mats) to be used in railway tracks.

75 FR 60036 - Federal Motor Vehicle Safety Standards; New Pneumatic Tires for Motor Vehicles With a GVWR of...

Science.gov (United States)

2010-09-29

... evaluates resistance to heat buildup when the tire is run at stepped-up loads at or near its rated load... that involves a tire running on the roadwheel under specified conditions to allow for tire growth. The... [Docket No. NHTSA-2010-0132] RIN 2127-AK17 Federal Motor Vehicle Safety Standards; New Pneumatic Tires for...

Zinc Leaching from Tire Crumb Rubber

Science.gov (United States)

Rhodes, E. P.; Ren, J.; Mays, D. C.

2010-12-01

Recent estimates indicate that more than 2 billion scrap tires are currently stockpiled in the United States and approximately 280 million more tires are added annually. Various engineering applications utilize recycled tires in the form of shredded tire crumb rubber. However, the use of tire crumb rubber may have negative environmental impacts, especially when the rubber comes into contact with water. A review of the literature indicates that leaching of zinc from tire crumb rubber is the most significant water quality concern associated with using this material. Zinc is generally used in tire manufacturing, representing approximately 1.3% of the final product by mass. This study will report results from the U.S. Environmental Protection Agency’s (EPA’s) Synthetic Precipitation Leaching Procedure, batch leaching tests, and column leaching tests performed to quantify the process by which zinc leaches from tire crumb rubber into water. Results are interpreted with a first-order kinetic attachment/detachment model, implemented with the U.S. Agricultural Research Service software HYDRUS-1D, in order to determine the circumstances when zinc leaching from tire crumb rubber would be expected to comply with the applicable discharge limits. One potential application for recycled tires is replacing sand with tire crumb rubber in granular media filters used for stormwater pollution control. For this to be a viable application, the total zinc in the stormwater discharge must be below the EPA’s benchmark value of 0.117 mg/L.

Utilization of waste tire rubber in manufacture of oriented strandboard.

Science.gov (United States)

Ayrilmis, Nadir; Buyuksari, Umit; Avci, Erkan

2009-09-01

Some physical and mechanical properties of oriented strandboards (OSBs) containing waste tire rubber at various addition levels based on the oven-dry strand weight, using the same method as that used in the manufacture of OSB. Two resin types, phenol-formaldehyde (PF) and polyisocyanate, were used in the experiments. The manufacturing parameters were: a specific gravity of 0.65 and waste tire rubber content (10/90, 20/80 and 30/70 by wt.% of waste tire rubber/wood strand). Average internal bond values of PF-bonded OSB panels with rubber chips were between 17.6% and 48.5% lower than the average of the control samples while polyisocyanate bonded OSBs were 16.5-50.6%. However, water resistance and mechanical properties of OSBs made using polyisocyanate resin were found to comply with general-purpose OSB minimum property requirements of EN 300 Type 1 (1997) values for use in dry conditions at the lowest tire rubber loading level (10%) based on the oven-dry panel weight. The tire rubber improved water resistance of the OSB panel due to its almost hydrophobic property. Based on the findings obtained from this study, we concluded that waste tire rubber could be used for general-purpose OSB manufacturing up to 10% ratio based on the oven-dry panel weight.

Effect of Friction Model and Tire Maneuvering on Tire-Pavement Contact Stress

OpenAIRE

Haichao Zhou; Guolin Wang; Yangmin Ding; Jian Yang; Chen Liang; Jing Fu

2015-01-01

This paper aims to simulate the effects of different friction models on tire braking. A truck radial tire (295/80R22.5) was modeled and the model was validated with tire deflection. An exponential decay friction model that considers the effect of sliding velocity on friction coefficients was adopted for analyzing braking performance. The result shows that the exponential decay friction model used for evaluating braking ability meets design requirements of antilock braking system (ABS). The ti...

Abrasive wear of ceramic wear protection at ambient and high temperatures

Science.gov (United States)

Varga, M.; Adam, K.; Tumma, M.; Alessio, K. O.

2017-05-01

Ceramic wear protection is often applied in abrasive conditions due to their excellent wear resistance. This is especially necessary in heavy industries conveying large amounts of raw materials, e.g. in steel industry. Some plants also require material transport at high temperatures and velocities, making the need of temperature stable and abrasion resistant wear protection necessary. Various types and wear behaviour of ceramic protection are known. Hence, the goal of this study is to identify the best suitable ceramic materials for abrasive conditions in harsh environments at temperatures up to 950°C and severe thermal gradients. Chamottes, known for their excellent thermal shock resistance are compared to high abrasion resistant ceramic wear tiles and a cost efficient cement-bounded hard compound. Testing was done under high-stress three-body abrasion regime with a modified ASTM G65 apparatus enabling for investigations up to ~950°C. Thereto heated abrasive is introduced into the wear track and also preheated ceramic samples were used and compared to ambient temperature experiments. Results indicate a significant temperature influence on chamottes and the hard compound. While the chamottes benefit from temperature increase, the cement-bounded hard compound showed its limitation at abrasive temperatures of 950°C. The high abrasion resistant wear tiles represented the materials with the best wear resistance and less temperature influence in the investigated range.

On the origin of spin-up processes in decaying two-dimensional turbulence

NARCIS (Netherlands)

Keetels, G.H.; Clercx, H.J.H.; van Heijst, G.J.F.

2010-01-01

A remarkable feature of two-dimensional turbulence in a square container with no-slip walls is the spontaneous production of angular momentum due to flow-wall interactions, also known as spontaneous spin-up of the flow. In this paper we address the statistics of spin-up and discuss its likely

30 CFR 57.14104 - Tire repairs.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tire repairs. 57.14104 Section 57.14104 Mineral... Devices and Maintenance Requirements § 57.14104 Tire repairs. (a) Before a tire is removed from a vehicle for tire repair, the valve core shall be partially removed to allow for gradual deflation and then...

30 CFR 56.14104 - Tire repairs.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tire repairs. 56.14104 Section 56.14104 Mineral... Devices and Maintenance Requirements § 56.14104 Tire repairs. (a) Before a tire is removed from a vehicle for tire repair, the valve core shall be partially removed to allow for gradual deflation and then...

Rubber tire leachates in the aquatic environment.

Science.gov (United States)

Evans, J J

1997-01-01

Tires have a deleterious effect on the environment. This review discusses the background of scrap tires discarded in the environment, including tire composition, adverse environmental effects, threats to public health and safety, and solid waste management. Despite the widespread use of scrap tires in environmental applications, both land-based and aquatic, data on the indicators of environmental degradation are extremely scarce. Indicators of environmental degradation include analysis of chemicals within the water and sediment, analysis of contaminants within organisms, and analysis of the biological effects of these compounds on plants, animals, microbes, and organelles. Although these indicators are most useful when used in parallel, a review of the available information on chemical characterization of tire leachate from tire storage facilities, manufacturing, usage in recycling applications, and toxicity exposure studies, of vegetation surveys from waste tire areas and reviews of mammalian tire product toxicity, and of toxicity, mutagenicity, and carcinogenicity of tire exposure in experimental aquatic animals, microbes, and organelles is presented. The major characteristics of these studies are discussed in specific sections. The "Discussion and Conclusions" section discusses and summarizes the biological effects and chemical characterization of tire leachates. A global environmental perspective is included to improve our understanding of the deficiency of the current knowledge of tire leachate toxicity from various sources and to encourage interdisciplinary studies to establish the pattern of pollution associated with waste tire management.

The Use of Deconstructed Tires as Elastic Elements in Railway Tracks

Science.gov (United States)

Sol-Sánchez, Miguel; Moreno-Navarro, Fernando; Rubio-Gámez, Mª Carmen

2014-01-01

Elastic elements such as rail pads, under sleeper pads and under ballast mats are railway components that allow for a reduction in track deterioration and vibrations. And they are furthermore commonly used to obtain an optimal vertical stiffness of the infrastructure. However, the use of elastomeric materials can increase construction costs and the consumption of raw materials. Thus, the utilization of used tire layers offers an alternative to reuse an abundant waste reducing the cost of elastic elements. In addition, an innovator technique allows deconstructing tire layers without grinding up the material, reducing production costs at the same time that tire properties are remained. This research is focused on the study of the viability of developing elastic components from used tire layers by evaluating the influence of thickness, the resistance capacity of the elements and their behavior in a ballast box. Results indicate the ability of tire pads to manufacture elastic elements (rail pads, under sleeper pads and under ballast mats) to be used in railway tracks. PMID:28788168

The Use of Deconstructed Tires as Elastic Elements in Railway Tracks

Directory of Open Access Journals (Sweden)

Miguel Sol-Sánchez

2014-08-01

Full Text Available Elastic elements such as rail pads, under sleeper pads and under ballast mats are railway components that allow for a reduction in track deterioration and vibrations. And they are furthermore commonly used to obtain an optimal vertical stiffness of the infrastructure. However, the use of elastomeric materials can increase construction costs and the consumption of raw materials. Thus, the utilization of used tire layers offers an alternative to reuse an abundant waste reducing the cost of elastic elements. In addition, an innovator technique allows deconstructing tire layers without grinding up the material, reducing production costs at the same time that tire properties are remained. This research is focused on the study of the viability of developing elastic components from used tire layers by evaluating the influence of thickness, the resistance capacity of the elements and their behavior in a ballast box. Results indicate the ability of tire pads to manufacture elastic elements (rail pads, under sleeper pads and under ballast mats to be used in railway tracks.

Tire Development for Effective Transportation and Utilization of Used Tires, CRADA 01-N044, Final Report

Energy Technology Data Exchange (ETDEWEB)

Susan M. Maley

2004-03-31

Scrap tires represent a significant disposal and recycling challenge for the United States. Over 280 million tires are generated on an annual basis, and several states have large stockpiles or abandoned tire piles that are slated for remediation. While most states have programs to address the accumulation and generation of scrap tires, most of these states struggle with creating and sustaining recycling or beneficial end use markets. One of the major issues with market development has been the costs associated with transporting and processing the tires into material for recycling or disposal. According to a report by the Rubber Manufactures Association tire-derived fuel (TDF) represents the largest market for scrap tires, and approximately 115 million tires were consumed in 2001 as TDF (U.S. Scrap Tire Markets, 2001, December 2002, www.rma.org/scraptires). This market is supported primarily by cement kilns, followed by various industries including companies that operate utility and industrial boilers. However the use of TDF has not increased and the amount of TDF used by boiler operators has declined. The work completed through this cooperative research and development agreement (CRADA) has shown the potential of a mobile tire shredding unit to economically produce TDF and to provide an alterative low cost fuel to suitable coal-fired power systems. This novel system addresses the economic barriers by processing the tires at the retailer, thereby eliminating the costs associated with hauling whole tires. The equipment incorporated into the design allow for small 1-inch chunks of TDF to be produced in a timely fashion. The TDF can then be co-fired with coal in suitable combustion systems, such as a fluidized bed. Proper use of TDF has been shown to boost efficiency and reduce emissions from power generation systems, which is beneficial to coal utilization in existing power plants. Since the original scope of work outlined in the CRADA could not be completed because

49 CFR 574.5 - Tire identification requirements.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Tire identification requirements. 574.5 Section... SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) TIRE IDENTIFICATION AND RECORDKEEPING § 574.5 Tire identification requirements. Each tire manufacturer shall conspicuously label on one...

Intelligent tires for identifying coefficient of friction of tire/road contact surfaces using three-axis accelerometer

International Nuclear Information System (INIS)

Matsuzaki, Ryosuke; Kamai, Kazuto; Seki, Ryosuke

2015-01-01

Intelligent tires equipped with sensors as well as the monitoring of the tire/road contact conditions are in demand for improving vehicle control and safety. With the aim of identifying the coefficient of friction of tire/road contact surfaces during driving, including during cornering, we develop an identification scheme for the coefficient of friction that involves estimation of the slip angle and applied force by using a single lightweight three-axis accelerometer attached on the inner surface of the tire. To validate the developed scheme, we conduct tire-rolling tests using an accelerometer-equipped tire with various slip angles on various types of road surfaces, including dry and wet surfaces. The results of these tests confirm that the estimated slip angle and applied force are reasonable. Furthermore, the identified coefficient of friction by the developed scheme agreed with that measured by standardized tests. (paper)

Processing Satellite Imagery To Detect Waste Tire Piles

Science.gov (United States)

Skiles, Joseph; Schmidt, Cynthia; Wuinlan, Becky; Huybrechts, Catherine

2007-01-01

A methodology for processing commercially available satellite spectral imagery has been developed to enable identification and mapping of waste tire piles in California. The California Integrated Waste Management Board initiated the project and provided funding for the method s development. The methodology includes the use of a combination of previously commercially available image-processing and georeferencing software used to develop a model that specifically distinguishes between tire piles and other objects. The methodology reduces the time that must be spent to initially survey a region for tire sites, thereby increasing inspectors and managers time available for remediation of the sites. Remediation is needed because millions of used tires are discarded every year, waste tire piles pose fire hazards, and mosquitoes often breed in water trapped in tires. It should be possible to adapt the methodology to regions outside California by modifying some of the algorithms implemented in the software to account for geographic differences in spectral characteristics associated with terrain and climate. The task of identifying tire piles in satellite imagery is uniquely challenging because of their low reflectance levels: Tires tend to be spectrally confused with shadows and deep water, both of which reflect little light to satellite-borne imaging systems. In this methodology, the challenge is met, in part, by use of software that implements the Tire Identification from Reflectance (TIRe) model. The development of the TIRe model included incorporation of lessons learned in previous research on the detection and mapping of tire piles by use of manual/ visual and/or computational analysis of aerial and satellite imagery. The TIRe model is a computational model for identifying tire piles and discriminating between tire piles and other objects. The input to the TIRe model is the georeferenced but otherwise raw satellite spectral images of a geographic region to be surveyed

Survivability Enhanced Run-Flat Variable Footprint Tires

Science.gov (United States)

2010-08-17

with tire tread . By varying the thickness and geometry of the polyurethane soft layer, this unique tire -wheel assembly can generate a wide array of...carcass severely damaged/punctured, provide the same dynamic deflection as the normal pneumatic tire , and provide similar tread life. Could a tire be...be for an optimized shape. Fig 8 shows the actual process applied to a current tire . The carbon fiber was added by removing the tread , cutting

Model-based state estimator for an intelligent tire

NARCIS (Netherlands)

Goos, J.; Teerhuis, A. P.; Schmeitz, A. J.C.; Besselink, I.; Nijmeijer, H.

2017-01-01

In this work a Tire State Estimator (TSE) is developed and validated using data from a tri-axial accelerometer, installed at the inner liner of the tire. The Flexible Ring Tire (FRT) model is proposed to calculate the tire deformation. For a rolling tire, this deformation is transformed into

Model-based State Estimator for an Intelligent Tire

NARCIS (Netherlands)

Goos, J.; Teerhuis, A.P.; Schmeitz, A.J.C.; Besselink, I.J.M.; Nijmeijer, H.

2016-01-01

In this work a Tire State Estimator (TSE) is developed and validated using data from a tri-axial accelerometer, installed at the inner liner of the tire. The Flexible Ring Tire (FRT) model is proposed to calculate the tire deformation. For a rolling tire, this deformation is transformed into

40 CFR 202.23 - Visual tire inspection.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Visual tire inspection. 202.23 Section... Visual tire inspection. No motor carrier subject to these regulations shall at any time operate any motor vehicle of a type to which this regulation is applicable on a tire or tires having a tread pattern which...

Airplane tire inspection by image processing techniques

OpenAIRE

Jovancevic , Igor; Arafat , Al; Orteu , Jean-José; Sentenac , Thierry

2016-01-01

International audience; In this paper, we propose a new approach to detect and inspect airplane tires. We use normalized correlation based template matching to detect tires and GrabCut segmentation method to extract them from the background. We inspect the tires condition by investigating the tire treads. Ridge based intensity profiling gives satisfying inspection results.

Vehicle Tire and Wheel Creation in BRL-CAD

Science.gov (United States)

2009-04-01

Tire Tread Modeling 4  4.  Setting Tire Thickness 7  5.  Changing the Rim Width 9  6.  Changing the Radial Location of the... treaded or nontreaded model in the tire -model.c combination based on the analysis. 4. Setting Tire Thickness Tire thickness is manipulated via... tread is not modeled by default but can be added using options. • Fine-grained control of parameters such as tire thickness is available with

To the question of modeling of wheels and rails wear processes

Directory of Open Access Journals (Sweden)

S.V. Myamlin

2013-06-01

Full Text Available Purpose. There is a need of wear process modeling in the wheel-rail system. This is related to the fact that the wear processes in this system are absolutely different in the initial and final stages. The profile change of rail and, especially, of the wheels caused by the wear significantly affects the rolling stock dynamics, traffic safety and the resource of the wheels and rails. Wear modeling and the traffic safety evaluation requires the accounting of the low frequency component forces (including the modeling of transitional areas affecting the wheel on the side of the rail and carriage in motion of rolling stock, so the statistical analysis is not possible. Methodology. The method of mathematical modeling of the wheel set and the rail interaction was used during the research conducting. Findings. As a result of the modeling of the wheel set motion on the rail track, the mathematic model with 19 freedom degrees was obtained. This model takes into account the axle torque and studies wheels constructions as the components of the mechanical systems, consisting of a hub and tire. Originality. The mathematic model allows evaluating the wear degree of the wheels and rails when using on the rolling stock not only all-metal wheel sets, but also compound ones with the use of spring wheels and independent rotation of semi-axes with the wheels. Practical value. The development of the improved mathematical model of freight car wheel set motion with differential rotation of the wheels and compound axles allows studying the wear processes of wheels and rails.

Studless Winter Tires

Science.gov (United States)

1976-01-01

Goodyear Tire and Rubber Company developed a material for Johnson Space Center used as parachute shrouds to soft land the Vikings through the tenuous Martian atmosphere and has been adapted to new radial tire five times stronger than steel. Fiber has a chain-like molecular structure that gives it incredible strength in proportion to its weight. Material is expected to increase tread life by 10,000 miles.

Compressive Strength and Modulus of Elasticity of Concrete with Cubed Waste Tire Rubbers as Coarse Aggregates

Science.gov (United States)

Haryanto, Y.; Hermanto, N. I. S.; Pamudji, G.; Wardana, K. P.

2017-11-01

One feasible solution to overcome the issue of tire disposal waste is the use of waste tire rubber to replace aggregate in concrete. We have conducted an experimental investigation on the effect of rubber tire waste aggregate in cuboid form on the compressive strength and modulus of elasticity of concrete. The test was performed on 72 cylindrical specimens with the height of 300 mm and diameter of 150 mm. We found that the workability of concrete with waste tire rubber aggregate has increased. The concrete density with waste tire rubber aggregate was decreased, and so was the compressive strength. The decrease of compressive strength is up to 64.34%. If the content of waste tire rubber aggregate is more than 40%, then the resulting concrete cannot be categorized as structural concrete. The modulus of elasticity decreased to 59.77%. The theoretical equation developed to determine the modulus of elasticity of concrete with rubber tire waste aggregate has an accuracy of 84.27%.

49 CFR 230.113 - Wheels and tire defects.

Science.gov (United States)

2010-10-01

... tires may not have a seam running lengthwise that is within 33/4 inches of the flange. (g) Worn flanges... 49 Transportation 4 2010-10-01 2010-10-01 false Wheels and tire defects. 230.113 Section 230.113... Tenders Wheels and Tires § 230.113 Wheels and tire defects. Steam locomotive and tender wheels or tires...

Tire-road noise: an experimental study of tire and road design parameters

NARCIS (Netherlands)

Bekke, Dirk; Wijnant, Ysbrand H.; Weegerink, Thijs; de Boer, Andries

2013-01-01

It is widely known that road traffic noise has negative influences on human health. Hence, as tire-road noise is considered to be the most dominant cause of road traffic noise above 30-50 km/h, a lot of research is performed by the two involving industries: road authorities/manufacturers and tire

THE EFFECT OF TRANSIENT ACCRETION ON THE SPIN-UP OF MILLISECOND PULSARS

Energy Technology Data Exchange (ETDEWEB)

Bhattacharyya, Sudip; Chakrabarty, Deepto, E-mail: sudip@tifr.res.in [Department of Astronomy and Astrophysics, Tata Institute of Fundamental Research, 1 Homi Bhabha Road, Colaba, Mumbai 400005 (India)

2017-01-20

A millisecond pulsar is a neutron star that has been substantially spun up by accretion from a binary companion. A previously unrecognized factor governing the spin evolution of such pulsars is the crucial effect of nonsteady or transient accretion. We numerically compute the evolution of accreting neutron stars through a series of outburst and quiescent phases, considering the drastic variation of the accretion rate and the standard disk–magnetosphere interaction. We find that, for the same long-term average accretion rate, X-ray transients can spin up pulsars to rates several times higher than can persistent accretors, even when the spin-down due to electromagnetic radiation during quiescence is included. We also compute an analytical expression for the equilibrium spin frequency in transients, by taking spin equilibrium to mean that no net angular momentum is transferred to the neutron star in each outburst cycle. We find that the equilibrium spin rate for transients, which depends on the peak accretion rate during outbursts, can be much higher than that for persistent sources. This explains our numerical finding. This finding implies that any meaningful study of neutron star spin and magnetic field distributions requires the inclusion of the transient accretion effect, since most accreting neutron star sources are transients. Our finding also implies the existence of a submillisecond pulsar population, which is not observed. This may point to the need for a competing spin-down mechanism for the fastest-rotating accreting pulsars, such as gravitational radiation.

NASA evaluation of Type 2 chemical depositions. [effects of deicer deposition on aircraft tire friction performance

Science.gov (United States)

Yager, Thomas J.; Stubbs, Sandy M.; Howell, W. Edward; Webb, Granville L.

1993-01-01

Recent findings from NASA Langley tests to define effects of aircraft Type 2 chemical deicer depositions on aircraft tire friction performance are summarized. The Aircraft Landing Dynamics Facility (ALDF) is described together with the scope of the tire cornering and braking friction tests conducted up to 160 knots ground speed. Some lower speed 32 - 96 km/hr (20 - 60 mph) test run data obtained using an Instrumented Tire Test Vehicle (ITTV) to determine effects of tire bearing pressure and transverse grooving on cornering friction performance are also discussed. Recommendations are made concerning which parameters should be evaluated in future testing.

Release of Waste Tire Comprehensive Utilization Industry Access Conditions

Institute of Scientific and Technical Information of China (English)

2012-01-01

On July 31, 2012, the Ministry of Industry and Information Technology released the Tire Retread- ing lndustry Access Conditions and Waste Tire Comprehensive Utilization Industry Access Condi- tions with the No. 32 announcement of 2012. The state will lay a foundation for realizing the green, safe, efficient, eco-friendly and energy saving tar- gets in the "12th Five-year Plan" of the industry by raising access conditions, regulating industrial development order, strengthening environmental protection, promoting corporate optimizing and up- grading, improving resources comprehensive utiliza- tion technology and management level and guiding the "harmless recycling and eco-friendly utiliza- tion" of the industry.

Evaluation of the tire pressure influence on the lateral forces that occur between tire and road

Science.gov (United States)

Cordoş, N.; Todoruţ, A.; Barabás, I.

2017-10-01

The main objective of the paper is to capture the behavior of a vehicle on a race circuit, depending on the different inflation pressures of the tires (underpressure and overpressure). Taking into account that in the cornering the forces and the moments of inertia rise due the vehicle mass, and an inertial force decomposes in two components, one in the longitudinal plane and one in the transverse plane, the work aims the assessing the lateral forces that appear, to the contact between the tires and the tread, depending on the inflation pressure. The results have a graphic interpretation, enabling a comparative study of them. Results have been obtained regarding the lateral tire forces that occur between the tire and the road. The differences between these forces were particularly noticeable in cornering, and the differences between these forces were interpreted according to the tire inflation pressure.

A Tire-Sulfur Hybrid Adsorption Denitrification (T-SHAD) process for decentralized wastewater treatment.

Science.gov (United States)

Krayzelova, Lucie; Lynn, Thomas J; Banihani, Qais; Bartacek, Jan; Jenicek, Pavel; Ergas, Sarina J

2014-09-15

Nitrogen discharges from decentralized wastewater treatment (DWT) systems contribute to surface and groundwater contamination. However, the high variability in loading rates, long idle periods and lack of regular maintenance presents a challenge for biological nitrogen removal in DWT. A Tire-Sulfur Hybrid Adsorption Denitrification (T-SHAD) process was developed that combines nitrate (NO3(-)) adsorption to scrap tire chips with sulfur-oxidizing denitrification. This allows the tire chips to adsorb NO3(-) when the influent loading exceeds the denitrification capacity of the biofilm and release it when NO3(-) loading rates are low (e.g. at night). Three waste products, scrap tire chips, elemental sulfur pellets and crushed oyster shells, were used as a medium in adsorption, leaching, microcosm and up-flow packed bed bioreactor studies of NO3(-) removal from synthetic nitrified DWT wastewater. Adsorption isotherms showed that scrap tire chips have an adsorption capacity of 0.66 g NO3(-)-N kg(-1) of scrap tires. Leaching and microcosm studies showed that scrap tires leach bioavailable organic carbon that can support mixotrophic metabolism, resulting in lower effluent SO4(2-) concentrations than sulfur oxidizing denitrification alone. In column studies, the T-SHAD process achieved high NO3(-)-N removal efficiencies under steady state (90%), variable flow (89%) and variable concentration (94%) conditions. Copyright © 2014 Elsevier Ltd. All rights reserved.

Rubber friction and tire dynamics

International Nuclear Information System (INIS)

Persson, B N J

2011-01-01

We propose a simple rubber friction law, which can be used, for example, in models of tire (and vehicle) dynamics. The friction law is tested by comparing numerical results to the full rubber friction theory (Persson 2006 J. Phys.: Condens. Matter 18 7789). Good agreement is found between the two theories. We describe a two-dimensional (2D) tire model which combines the rubber friction model with a simple mass-spring description of the tire body. The tire model is very flexible and can be used to accurately calculate μ-slip curves (and the self-aligning torque) for braking and cornering or combined motion (e.g. braking during cornering). We present numerical results which illustrate the theory. Simulations of anti-blocking system (ABS) braking are performed using two simple control algorithms.

Rubber friction and tire dynamics.

Science.gov (United States)

Persson, B N J

2011-01-12

We propose a simple rubber friction law, which can be used, for example, in models of tire (and vehicle) dynamics. The friction law is tested by comparing numerical results to the full rubber friction theory (Persson 2006 J. Phys.: Condens. Matter 18 7789). Good agreement is found between the two theories. We describe a two-dimensional (2D) tire model which combines the rubber friction model with a simple mass-spring description of the tire body. The tire model is very flexible and can be used to accurately calculate μ-slip curves (and the self-aligning torque) for braking and cornering or combined motion (e.g. braking during cornering). We present numerical results which illustrate the theory. Simulations of anti-blocking system (ABS) braking are performed using two simple control algorithms.

A North American model to contain the spread of Aedes albopictus through tire legislation.

Science.gov (United States)

Novak, R J

1995-12-01

The introduction, spread, and establishment of the Asian tiger mosquito, Aedes albopictus, in the United States has been facilitated by used or waste tires. This species has not only caused considerable concern among public health officials but also highlighted that the growing accumulations of used tires are a serious solid waste problem and a challenge to the recycling industry. This paper illustrates how the State of Illinois addressed the public health and solid waste problems associated with waste tires, mosquitoes and mosquito-borne pathogens. The goal of the State was to develop and implement through legislative process the Illinois Waste Tire Act. The purpose of the Waste Tire Act is: 1) to ensure that used and waste tires are collected for disposal and recycling, 2) to provide for the abatement of used and waste tire dumps and associated threats to public health, 3) to encourage the development of used and waste tire processing facilities and technologies, including energy recovery, and 4) to provide for research on vectors associated with used and waste tires, and the diseases they spread. The discussion will include key statutes from the Act and the model used to coordinate the effort of five different governmental agencies. An up-to-date presentation of vector-related research, mandated by the Act, ranging from applied investigations on mosquito control to more basic studies investigations on virus identification using molecular technology will be discussed. Finally a discussion of problems that have been encountered along with solutions dealing with legislative language, multidisciplined agency efforts and interactions with the general public are presented.

Nonlinear Analysis and Modeling of Tires

Science.gov (United States)

Noor, Ahmed K.

1996-01-01

The objective of the study was to develop efficient modeling techniques and computational strategies for: (1) predicting the nonlinear response of tires subjected to inflation pressure, mechanical and thermal loads; (2) determining the footprint region, and analyzing the tire pavement contact problem, including the effect of friction; and (3) determining the sensitivity of the tire response (displacements, stresses, strain energy, contact pressures and contact area) to variations in the different material and geometric parameters. Two computational strategies were developed. In the first strategy the tire was modeled by using either a two-dimensional shear flexible mixed shell finite elements or a quasi-three-dimensional solid model. The contact conditions were incorporated into the formulation by using a perturbed Lagrangian approach. A number of model reduction techniques were applied to substantially reduce the number of degrees of freedom used in describing the response outside the contact region. The second strategy exploited the axial symmetry of the undeformed tire, and uses cylindrical coordinates in the development of three-dimensional elements for modeling each of the different parts of the tire cross section. Model reduction techniques are also used with this strategy.

Mechanical Properties Experimental Study of Engineering Vehicle Refurbished Tire

Science.gov (United States)

Qiang, Wang; Xiaojie, Qi; Zhao, Yang; Yunlong, Wang; Guotian, Wang; Degang, Lv

2018-05-01

The vehicle refurbished tire test system was constructed, got load-deformation, load-stiffness, and load-compression ratio property laws of engineering vehicle refurbished tire under the working condition of static state and ground contact, and built radial direction loading deformation mathematics model of 26.5R25 engineering vehicle refurbished tire. The test results show that radial-direction and side-direction deformation value is a little less than that of the new tire. The radial-direction stiffness and compression ratio of engineering vehicle refurbished tire were greatly influenced by radial-direction load and air inflation pressure. When load was certain, radial-direction stiffness would increase with air inflation pressure increasing. When air inflation pressure was certain, compression ratio of engineering vehicle refurbished tire would enlarge with radial-direction load increasing, which was a little less than that of the new and the same type tire. Aging degree of old car-case would exert a great influence on deformation property of engineering vehicle refurbished tire, thus engineering vehicle refurbished tires are suitable to the working condition of low tire pressure and less load.

Empirical Analysis of Pneumatic Tire Friction on Ice

OpenAIRE

Holley, Troy Nigel

2010-01-01

Pneumatic tire friction on ice is an under-researched area of tire mechanics. This study covers the design and analysis of a series of pneumatic tire tests on a flat-level ice road surface. The terramechanics rig of the Advanced Vehicle Dynamics Lab (AVDL) is a single-wheel test rig that allows for the experimental analysis of the forces and moments on a tire, providing directly the data for the drawbar pull of said tire, thus supporting the calculation of friction based on this data. This...

Usage of post-consumer tires as raw materials

Directory of Open Access Journals (Sweden)

O.A. Vovk

2006-04-01

Full Text Available  This article is devoted to the problem of post-consumer tires accumulation and recycling both in Europe and Ukraine. It describes general tires properties, their structure and composite elements which are valuable secondary resources. Also there are analyzed the most known methods of used tires treatment and final product of tires utilizations.

Automobile Tire Assessment: A Multi-Criteria Approach

Directory of Open Access Journals (Sweden)

Ateekh-Ur-Rehman

2017-02-01

Full Text Available In response to the present dynamic market, automobile manufacturing industries are constantly evaluating and improving their manufacturing strategies to stay competitive. It is also evident that they evaluate those strategies considering multiple criteria. In one such case, an automobile project manager has to ensure that the selected tire (among the available alternatives complies with the prospective automobile’s performance. This paper presents an approach for the assessment of alternative automobile tires taking into account multiple criteria, such as tire sustainability, tire road performance, environmental issues, tire purchase cost and tire road grip. The presented approach is quite helpful to any decision maker who is interested not only in ranking alternatives but also in establishing the superiority of an alternative over others. The approach also helps to specify the position of each alternative with respect to ideal solution. A case illustration is used to demonstrate an application of the approach.

Use of shredded tire chips and tire crumbs as packing media in trickling filter systems for landfill leachate treatment.

Science.gov (United States)

Mondal, B; Warith, M A

2008-08-01

Scrap tire stockpiles are breeding grounds for pests, mosquitoes and west Nile viruses and, thereby, become a potential health risk. This experimental study was carried out in six stages to determine the suitability of shredded tire materials in a trickling filter system to treat landfill leachate. Biochemical oxygen demand (BOD5), chemical oxygen demand (COD) and NH3-N removals were obtained in the range of 81 to 96%, 76 to 90% and 15 to 68%, respectively. The removal of organics appears to be largely related to total dissolved solids reduction in leachate. A sudden increase, from time to time, in organic content of effluent could be attributed to biomass sloughing and clogging in the trickling filters. However, tire crumbs exhibited more consistent organics removal throughout the experimental program. Due to the high surface area of shredded tire chips and crumbs, a layer of biomass, 1-2 mm thick, was attached to them and was sloughed off at an interval of 21 days. Apart from that, as shredded tires are comparatively cheaper than any other usable packing material, tire chips and tire crumbs appeared to be quite promising as packing media in trickling filters for landfill leachate treatment.

Characterizing Tire Crumb Rubber for Exposure Assessment

Science.gov (United States)

Tire crumb rubber derived from recycled tires is widely used as infill material in synthetic turf fields in the United States. An estimated 95% of the over 12,000 installed fields in the U.S. use tire crumb rubber infill alone or mixed with sand or alternative materials. Concerns...

Tire Models for Use in Braking Applications

OpenAIRE

Svendenius, Jacob

2003-01-01

The tire is a significant part for control of a vehicle. For a well-working brake system the contact properties between the tire and the ground is the limiting factor for a safe braking. To get optimal performance it is important that the system can utilize all friction resources. The brush tire model was a popular method in the 1960's and 1970's before the empirical approaches became dominating. The brush model gives an educational interpretation of the physics behind the tire behavi...

Technical assessment of discarded tires gasification as alternative technology for electricity generation.

Science.gov (United States)

Machin, Einara Blanco; Pedroso, Daniel Travieso; de Carvalho, João Andrade

2017-10-01

Concern about contamination associated with the disposal of tires has led to the search for technologies to reuse discarded tires, which include the use of Tire Derived Fuel (TDF) as fuel in advanced thermal-conversion processes, this allows the energy use of these wastes at affordable costs and reduces the environmental impact on scrap tires disposal. A theoretical assessment of the technical viability of TDF gasification for electric and thermal power generation, from the producer gas combustion in an internal combustion engine and in a gas turbine, was performed. The combustion of producer gas derived from the gasification of TDF in an internal combustion engine driving a generator (ICE-G) appears as the more efficient route for electricity generation when compared with the efficiency obtained with the use of gas turbine (GT-G). A higher global efficiency, considering the electric and thermal generation efficiency can be expected with the use of TDF producer gas in GT-G, where is expected an overall efficiency of 77.49%. The assessment shows that is possible produces up to 7.67MJ and 10.62MJ of electric and thermal energy per kilogram of TDF gasified using an ICE-G and up to 6.06MJ and 13.03MJ of electric and thermal energy respectively per kilogram of gasified TDF using a GT-G. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tailpipe, resuspended road dust, and brake-wear emission factors from on-road vehicles

Science.gov (United States)

Abu-Allaban, Mahmoud; Gillies, John A.; Gertler, Alan W.; Clayton, Russ; Proffitt, David

Intensive mass and chemical measurements were performed at roadside locations in Reno, Nevada, and Durham/Research Triangle Park), North Carolina to derive tailpipe, resuspended road dust, and brake-wear emission factors from in-use vehicles. Continuous particulate matter (PM) data were utilized to derive total emission factors while integrated PM data were used to attribute the calculated emission factors to different mechanisms using chemical mass balance receptor modeling and scanning electron microscopy techniques. Resuspended road dust and tailpipe emissions were found to be the dominant mechanisms that contribute significantly to the total PM 10 and PM 2.5 emission factors, respectively. Small contributions from brake-wear were observed at locations where strong braking occurs, but no tire-wear was seen at any sampling location. PM 10 emission rates from light-duty spark ignition (LDSI) vehicles ranged from 40 to 780 mg/km, 10 to 70 mg/km, and 0 to 80 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 10 emission rates from heavy-duty vehicles ranged from 230 to 7800 mg/km, 60 to 570 mg/km, and 0 to 610 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 2.5 emission rates from LDSI vehicles ranged from 2 to 25 mg/km, 10 to 50 mg/km, and 0 to 5 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively. PM 2.5 emission rates from heavy-duty vehicles ranged from 15 to 300 mg/km, 60 to 480 mg/km, and 0 to 15 mg/km per vehicle for road dust, tailpipe, and brake-wear, respectively.

Method of sections in analytical calculations of pneumatic tires

Science.gov (United States)

Tarasov, V. N.; Boyarkina, I. V.

2018-01-01

Analytical calculations in the pneumatic tire theory are more preferable in comparison with experimental methods. The method of section of a pneumatic tire shell allows to obtain equations of intensities of internal forces in carcass elements and bead rings. Analytical dependencies of intensity of distributed forces have been obtained in tire equator points, on side walls (poles) and pneumatic tire bead rings. Along with planes in the capacity of secant surfaces cylindrical surfaces are used for the first time together with secant planes. The tire capacity equation has been obtained using the method of section, by means of which a contact body is cut off from the tire carcass along the contact perimeter by the surface which is normal to the bearing surface. It has been established that the Laplace equation for the solution of tasks of this class of pneumatic tires contains two unknown values that requires the generation of additional equations. The developed computational schemes of pneumatic tire sections and new equations allow to accelerate the pneumatic tire structure improvement process during engineering.

Friction and wear calculation methods

CERN Document Server

Kragelsky, I V; Kombalov, V S

1981-01-01

Friction and Wear: Calculation Methods provides an introduction to the main theories of a new branch of mechanics known as """"contact interaction of solids in relative motion."""" This branch is closely bound up with other sciences, especially physics and chemistry. The book analyzes the nature of friction and wear, and some theoretical relationships that link the characteristics of the processes and the properties of the contacting bodies essential for practical application of the theories in calculating friction forces and wear values. The effect of the environment on friction and wear is a

Forestry Tire Tractive Performance: New, Worn, and with Chains

Science.gov (United States)

C.R. Vechinski; C.R. Johnson; R.L. Raper; T.P. McDonald

1999-01-01

The tractive perfomance of a new tire, a worn tire, and a worn tire with forestry tire chains was measured in four soil types. Two of the soil types simulated forest-floor conditions with one soil type having a sulfate cover of pine straw and the other having a surface cover of sod. The two remaining soil types were bare. The worn tire with and without chains had...

An Analytical Tire Model with Flexible Carcass for Combined Slips

Directory of Open Access Journals (Sweden)

Nan Xu

2014-01-01

Full Text Available The tire mechanical characteristics under combined cornering and braking/driving situations have significant effects on vehicle directional controls. The objective of this paper is to present an analytical tire model with flexible carcass for combined slip situations, which can describe tire behavior well and can also be used for studying vehicle dynamics. The tire forces and moments come mainly from the shear stress and sliding friction at the tread-road interface. In order to describe complicated tire characteristics and tire-road friction, some key factors are considered in this model: arbitrary pressure distribution; translational, bending, and twisting compliance of the carcass; dynamic friction coefficient; anisotropic stiffness properties. The analytical tire model can describe tire forces and moments accurately under combined slip conditions. Some important properties induced by flexible carcass can also be reflected. The structural parameters of a tire can be identified from tire measurements and the computational results using the analytical model show good agreement with test data.

41 CFR 101-25.110 - Tire identification/registration program.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Tire identification...-General Policies § 101-25.110 Tire identification/registration program. The regulations issued by the Department of Transportation in 49 CFR part 574, Tire Identification and Recordkeeping, require that tire...

49 CFR 230.112 - Wheels and tires.

Science.gov (United States)

2010-10-01

... wheels mounted on the same axle shall not vary more than 1/4 inch. (d) Tire thickness. Wheels may not have tires with a minimum thickness less than that indicated in the table in this paragraph (d). When... the minimum thickness of tires may be as much below the limits specified earlier in this paragraph (d...

Geotechnical Properties of Rubber Tires and Sediments Mixtures

Directory of Open Access Journals (Sweden)

H. Sellaf

2014-04-01

Full Text Available An experimental work was undertaken to study the effect of rubber tires on the geotechnical properties of a dredged sediment, using a mixing ratio of large size. For comparison, two types of soil were studied (dredged sediment from Fergoug dam and Tizi Tuff from the north west of Algeria. Taking into account the high compressibility and the low water absorption of the rubber tires, grain size analysis, density, Atterberg limits analysis, chemical composition, direct shear tests, loading-unloading tests, modified Proctor and CBR tests are performed on the two soils and their mixtures with different scrap tire rubber (10, 20, 25 and 50%. The results show that liquid limits and plastic indexes decrease with the scrap tire rubber content and that the decrease is more significant for soil with high plasticity. Cohesion also decreases with scrap tire rubber content when the internal friction angle is vacillating. Compression and recompression indexes increase gradually with the scrap tire rubber content and the variation for compression index is more significant for the two soils. Compaction characteristics and CBR values decrease with scrap tire rubber content. The CBR values for W=3% are important compared to those with W=5% excepted for mixture with (75% tuff and 25% scrap tire rubber. The results show that the scrap tire rubber can be used as a reinforcement material for dredged soil, but with a content that should not highly affect the compressibility.

Recovery and disposal of discarded tires in the Taiwan area.

Science.gov (United States)

Hwang, J S; Roam, G D

1994-12-01

Urbanization and industrialization has resulted in a vast amount of artificial water containers in Taiwan, especially discarded automobile tires. 3.5 million automobile tires and several million motorcycle tires are discarded annually. The discarded tires contaminate the environment and also become a substantial number of breeding sites for the dengue vector mosquitoes. In order to establish a sound system for the recovery and disposal of discarded tires and to control dengue fever through source reduction, it has been emphasized that users must pay for their waste. It is necessary to recover and properly dispose of these discarded tired. The commercial firms which sell or manufacture tires are therefore advised to cooperate with the Environmental Protection Administration of the Executive Yuan, R.O.C. and follow the "Regulations of Recovery and Disposal of Discarded Tires". They are requested to establish foundations for the recovery of discarded tires. Those who are willing to join should prepay a deposit or related charge by the size of tire, which is imported or locally manufactured. The foundation utilizes the deposits for the recovery and disposal of discarded tires. From 1991 to 1993 the commercial tire firms had already achieved the 80% recovery rates declared by the authorities concerned. Some of the tires, after having been recovered, were recycled in the original form and the rest were cut into small pieces for recycling after physical treatment. It should be mentioned that the Department of Environmental Protection of Kaohsiung City has collected 80 thousand discarded automobile tires to be used as ocean jetty.(ABSTRACT TRUNCATED AT 250 WORDS)

Co-gasification of tire and biomass for enhancement of tire-char reactivity in CO2 gasification process.

Science.gov (United States)

Lahijani, Pooya; Zainal, Zainal Alimuddin; Mohamed, Abdul Rahman; Mohammadi, Maedeh

2013-06-01

In this investigation, palm empty fruit bunch (EFB) and almond shell (AS) were implemented as two natural catalysts rich in alkali metals, especially potassium, to enhance the reactivity of tire-char through co-gasification process. Co-gasification experiments were conducted at several blending ratios using isothermal Thermogravimetric analysis (TGA) under CO2. The pronounced effect of inherent alkali content of biomass-chars on promoting the reactivity of tire-char was proven when acid-treated biomass-chars did not exert any catalytic effect on improving the reactivity of tire-char in co-gasification experiments. In kinetic studies of the co-gasified samples in chemically-controlled regime, modified random pore model (M-RPM) was adopted to describe the reactive behavior of the tire-char/biomass-char blends. By virtue of the catalytic effect of biomass, the activation energy for tire-char gasification was lowered from 250 kJ/mol in pure form 203 to 187 kJ/mol for AS-char and EFB-char co-gasified samples, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

A Strain-Based Method to Detect Tires' Loss of Grip and Estimate Lateral Friction Coefficient from Experimental Data by Fuzzy Logic for Intelligent Tire Development.

Science.gov (United States)

Yunta, Jorge; Garcia-Pozuelo, Daniel; Diaz, Vicente; Olatunbosun, Oluremi

2018-02-06

Tires are a key sub-system of vehicles that have a big responsibility for comfort, fuel consumption and traffic safety. However, current tires are just passive rubber elements which do not contribute actively to improve the driving experience or vehicle safety. The lack of information from the tire during driving gives cause for developing an intelligent tire. Therefore, the aim of the intelligent tire is to monitor tire working conditions in real-time, providing useful information to other systems and becoming an active system. In this paper, tire tread deformation is measured to provide a strong experimental base with different experiments and test results by means of a tire fitted with sensors. Tests under different working conditions such as vertical load or slip angle have been carried out with an indoor tire test rig. The experimental data analysis shows the strong relation that exists between lateral force and the maximum tensile and compressive strain peaks when the tire is not working at the limit of grip. In the last section, an estimation system from experimental data has been developed and implemented in Simulink to show the potential of strain sensors for developing intelligent tire systems, obtaining as major results a signal to detect tire's loss of grip and estimations of the lateral friction coefficient.

AIR EMISSIONS FROM SCRAP TIRE COMBUSTION

Science.gov (United States)

The report discusses air emissions from two types of scrap tire combustion: uncontrolled and controlled. Uncontrolled sources are open tire fires, which produce many unhealthful products of incomplete combustion and release them directly into the atmosphere. Controlled combustion...

Simulation of Thermal Signature of Tires and Tracks

Science.gov (United States)

2012-08-01

the body-ply is a linear elastic material. To facilitate the analysis, the tire was divided into Tread and Sidewall by the dash line as shown in...only one element is assigned through the thickness of the tire . Therefore, the thickness of the element is the same as the thickness of the tire ...to the whole part of the 3D full tire in the thermal analysis. The average strain energy density for each part ( tread or sidewall) in the cross

A procedure for multi-objective optimization of tire design parameters

OpenAIRE

Nikola Korunović; Miloš Madić; Miroslav Trajanović; Miroslav Radovanović

2015-01-01

The identification of optimal tire design parameters for satisfying different requirements, i.e. tire performance characteristics, plays an essential role in tire design. In order to improve tire performance characteristics, formulation and solving of multi-objective optimization problem must be performed. This paper presents a multi-objective optimization procedure for determination of optimal tire design parameters for simultaneous minimization of strain energy density at two distinctive zo...

A procedure for multi-objective optimization of tire design parameters

Directory of Open Access Journals (Sweden)

Nikola Korunović

2015-04-01

Full Text Available The identification of optimal tire design parameters for satisfying different requirements, i.e. tire performance characteristics, plays an essential role in tire design. In order to improve tire performance characteristics, formulation and solving of multi-objective optimization problem must be performed. This paper presents a multi-objective optimization procedure for determination of optimal tire design parameters for simultaneous minimization of strain energy density at two distinctive zones inside the tire. It consists of four main stages: pre-analysis, design of experiment, mathematical modeling and multi-objective optimization. Advantage of the proposed procedure is reflected in the fact that multi-objective optimization is based on the Pareto concept, which enables design engineers to obtain a complete set of optimization solutions and choose a suitable tire design. Furthermore, modeling of the relationships between tire design parameters and objective functions based on multiple regression analysis minimizes computational and modeling effort. The adequacy of the proposed tire design multi-objective optimization procedure has been validated by performing experimental trials based on finite element method.

Technical Note: Reducing the spin-up time of integrated surface water–groundwater models

KAUST Repository

Ajami, H.

2014-06-26

One of the main challenges in catchment scale application of coupled/integrated hydrologic models is specifying a catchment\\'s initial conditions in terms of soil moisture and depth to water table (DTWT) distributions. One approach to reduce uncertainty in model initialization is to run the model recursively using a single or multiple years of forcing data until the system equilibrates with respect to state and diagnostic variables. However, such "spin-up" approaches often require many years of simulations, making them computationally intensive. In this study, a new hybrid approach was developed to reduce the computational burden of spin-up time for an integrated groundwater-surface water-land surface model (ParFlow.CLM) by using a combination of ParFlow.CLM simulations and an empirical DTWT function. The methodology is examined in two catchments located in the temperate and semi-arid regions of Denmark and Australia respectively. Our results illustrate that the hybrid approach reduced the spin-up time required by ParFlow.CLM by up to 50%, and we outline a methodology that is applicable to other coupled/integrated modelling frameworks when initialization from equilibrium state is required.

Technical Note: Reducing the spin-up time of integrated surface water–groundwater models

KAUST Repository

Ajami, H.

2014-12-12

One of the main challenges in the application of coupled or integrated hydrologic models is specifying a catchment\\'s initial conditions in terms of soil moisture and depth-to-water table (DTWT) distributions. One approach to reducing uncertainty in model initialization is to run the model recursively using either a single year or multiple years of forcing data until the system equilibrates with respect to state and diagnostic variables. However, such "spin-up" approaches often require many years of simulations, making them computationally intensive. In this study, a new hybrid approach was developed to reduce the computational burden of the spin-up procedure by using a combination of model simulations and an empirical DTWT function. The methodology is examined across two distinct catchments located in a temperate region of Denmark and a semi-arid region of Australia. Our results illustrate that the hybrid approach reduced the spin-up period required for an integrated groundwater–surface water–land surface model (ParFlow.CLM) by up to 50%. To generalize results to different climate and catchment conditions, we outline a methodology that is applicable to other coupled or integrated modeling frameworks when initialization from an equilibrium state is required.

Tire traces - discrimination and classification of pyrolysis-GC/MS profiles.

Science.gov (United States)

Gueissaz, Line; Massonnet, Geneviève

2013-07-10

Tire traces can be observed on several crime scenes as vehicles are often used by criminals. The tread abrasion on the road, while braking or skidding, leads to the production of small rubber particles which can be collected for comparison purposes. This research focused on the statistical comparison of Py-GC/MS profiles of tire traces and tire treads. The optimisation of the analytical method was carried out using experimental designs. The aim was to determine the best pyrolysis parameters regarding the repeatability of the results. Thus, the pyrolysis factor effect could also be calculated. The pyrolysis temperature was found to be five time more important than time. Finally, a pyrolysis at 650°C during 15s was selected. Ten tires of different manufacturers and models were used for this study. Several samples were collected on each tire, and several replicates were carried out to study the variability within each tire (intravariability). More than eighty compounds were integrated for each analysis and the variability study showed that more than 75% presented a relative standard deviation (RSD) below 5% for the ten tires, thus supporting a low intravariability. The variability between the ten tires (intervariability) presented higher values and the ten most variant compounds had a RSD value above 13%, supporting their high potential of discrimination between the tires tested. Principal Component Analysis (PCA) was able to fully discriminate the ten tires with the help of the first three principal components. The ten tires were finally used to perform braking tests on a racetrack with a vehicle equipped with an anti-lock braking system. The resulting tire traces were adequately collected using sheets of white gelatine. As for tires, the intravariability for the traces was found to be lower than the intervariability. Clustering methods were carried out and the Ward's method based on the squared Euclidean distance was able to correctly group all of the tire traces

Effect of wheelchair mass, tire type and tire pressure on physical strain and wheelchair propulsion technique

NARCIS (Netherlands)

de Groot, Sonja; Vegter, Riemer J. K.; van der Woude, Lucas H. V.

2013-01-01

The purpose of this study was to evaluate the effect of wheelchair mass, solid vs. pneumatic tires and tire pressure on physical strain and wheelchair propulsion technique. 11 Able-bodied participants performed 14 submaximal exercise blocks on a treadmill with a fixed speed (1.11 m/s) within 3 weeks

Replacing coal by tire powder in ceramic industry

Energy Technology Data Exchange (ETDEWEB)

Mothe, C.G. [Dept. de Processos Organicos, Escola de Quimica/CT/UFRJ, Rio de Janeiro, RJ (Brazil); Mothe Filho, H.F. [Dept. de Geociencias, Inst. de Agronomia/UFRRJ, Seropedica, RJ (Brazil)

2005-07-01

Nowadays preserving nature, recycling or reusing materials are good policies. Around ten million tires are put out by year in Brazil, and it is not known for how long they will remain in environment till their complete degradation. This research used tires to replace coal in ceramic processing. In this way it helps to protect environment, to reduce the consumption of mineral deposits and to save money. Results show that tire powder can replace coal to obtain ceramic material, using one percent of tire. Experiments were carried out using TA instruments SDT 2960, in air or nitrogen atmospheres, at heating rate of 10 C/min., flow 120 ml/min. TG/DTA curves of tire and coal have exothermic events at close temperatures between 450-600 C. At range of temperatures clay have endothermic events. (orig.)

Evaluation of Tire/Surfacing/Base Contact Stresses and Texture Depth

Directory of Open Access Journals (Sweden)

W.J.vdM. Steyn

2015-03-01

Full Text Available Tire rolling resistance has a major impact on vehicle fuel consumption. Rolling resistance is the loss of energy due to the interaction between the tire and the pavement surface. This interaction is a complicated combination of stresses and strains which depend on both tire and pavement related factors. These include vehicle speed, vehicle weight, tire material and type, road camber, tire inflation pressure, pavement surfacing texture etc. In this paper the relationship between pavement surface texture depth and tire/surfacing contact stress and area is investigated. Texture depth and tire/surfacing contact stress were measured for a range of tire inflation pressures on five different pavement surfaces. In the analysis the relationship between texture and the generated contact stresses as well as the contact stress between the surfacing and base layer are presented and discussed, and the anticipated effect of these relationships on the rolling resistance of vehicles on the surfacings, and subsequent vehicle fuel economy discussed.

Loading Deformation Characteristic Simulation Study of Engineering Vehicle Refurbished Tire

Science.gov (United States)

Qiang, Wang; Xiaojie, Qi; Zhao, Yang; Yunlong, Wang; Guotian, Wang; Degang, Lv

2018-05-01

The paper constructed engineering vehicle refurbished tire computer geometry model, mechanics model, contact model, finite element analysis model, did simulation study on load-deformation property of engineering vehicle refurbished tire by comparing with that of the new and the same type tire, got load-deformation of engineering vehicle refurbished tire under the working condition of static state and ground contact. The analysis result shows that change rules of radial-direction deformation and side-direction deformation of engineering vehicle refurbished tire are close to that of the new tire, radial-direction and side-direction deformation value is a little less than that of the new tire. When air inflation pressure was certain, radial-direction deformation linear rule of engineer vehicle refurbished tire would increase with load adding, however, side-direction deformation showed linear change rule, when air inflation pressure was low; and it would show increase of non-linear change rule, when air inflation pressure was very high.

In-plane Tire Deformation Measurement Using a Multi-Laser Sensor System

OpenAIRE

Xiong, Yi

2016-01-01

The interactions between tires and roads are basic mechanisms that alter the dynamic states of vehicles. A fundamental understanding of tire-road interactions is clearly demanded in tire design to achieve performance improvements. The emergence of various tire sensors provides an opportunity to make accurate measurement of the physical quantities that are involved in tire-road interactions.  This thesis aims to measure and analyze the in-plane deformation of rolling tires through its direc...

Proceedings of Two Symposia on Nondestructive Testing of Tires

Science.gov (United States)

1978-05-01

understanding of this tire inspection area. But this better technical understanding will not guar - antee the success of either the industry or...control. Tires with very dark sur- face may be sprayed with talcum powder to improve their reflectance. Depending upon tire type and the required tire...products there has been a tendency to use some natural or synthetic cross-linking polymer gums which under extended heat conditions have tended to

Three Three-Axis IEPE Accelerometers on the Inner Liner of a Tire for Finding the Tire-Road Friction Potential Indicators.

Science.gov (United States)

Niskanen, Arto; Tuononen, Ari J

2015-08-05

Direct tire-road contact friction estimation is essential for future autonomous cars and active safety systems. Friction estimation methods have been proposed earlier for driving conditions in the presence of a slip angle or slip ratio. However, the estimation of the friction from a freely-rolling tire is still an unsolved topic. Knowing the existing friction potential would be beneficial since vehicle control systems could be adjusted before any remarkable tire force has been produced. Since accelerometers are well-known and robust, and thus a promising sensor type for intelligent tires, this study uses three three-axis IEPE accelerometers on the inner liner of a tire to detect friction potential indicators on two equally smooth surfaces with different friction levels. The equal roughness was chosen for both surfaces in order to study the friction phenomena by neglecting the effect of surface texture on vibrations. The acceleration data before the contact is used to differentiate the two friction levels between the tire and the road. In addition, the contact lengths from the three accelerometers are used to validate the acceleration data. A method to differentiate the friction levels on the basis of the acceleration signal is also introduced.

49 CFR 229.75 - Wheels and tire defects.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Wheels and tire defects. 229.75 Section 229.75....75 Wheels and tire defects. Wheels and tires may not have any of the following conditions: (a) A... two adjoining spots that are each two or more inches in length. (e) A seam running lengthwise that is...

Ontario tire recycling and economic development (OnTRED) plan : a market approach to eliminating tire stockpiles and promoting recycled rubber product manufacturing in Ontario

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-05-15

Details of the Ontario Tire Recycling and Economic Development (OnTRED) plan were presented. The plan was developed to address deficiencies in the Ontario Tire Stewardship's (OTS) Scrap Tire Diversion Program plan. The OTS promotes the burning of scrap tires contrary to the Waste Diversion Act, and transfers the financial responsibility for scrap tire management from manufacturers to retailers. The OnTRED plan will attempt to improve the current 87 per cent recovery rate for passenger scrap tires in Ontario, and prevent the formation of any new tire stockpiles. The aim of the OnTRED plan is to ensure reuse and recycling consistent with provisions in the Waste Diversion Act and enhance the existing workings of the tire and scrap tire market through the promotion of reuse and recycling. In addition, the plan aims to minimize administration and compliance costs. A program summary of the OnTRED plan was presented, as well as details of market development plans and buy-recycled rebates. Issues concerning collector registration and transaction tracking were presented, as well as details of brand-owner and first importer pay-in models. Stakeholder roles and responsibilities were reviewed. A budget scenario was presented, as well as a rebate and diversion scenario. It was concluded that Ontario's 87 per cent scrap tire diversion rate can be improved through a focus on patterns of reuse and recycling. 3 tabs., 7 figs.

An evaluation of string theory for the prediction of dynamic tire properties using scale model aircraft tires

Science.gov (United States)

Clark, S. K.; Dodge, R. N.; Nybakken, G. H.

1972-01-01

The string theory was evaluated for predicting lateral tire dynamic properties as obtained from scaled model tests. The experimental data and string theory predictions are in generally good agreement using lateral stiffness and relaxation length values obtained from the static or slowly rolling tire. The results indicate that lateral forces and self-aligning torques are linearly proportional to tire lateral stiffness and to the amplitude of either steer or lateral displacement. In addition, the results show that the ratio of input excitation frequency to road speed is the proper independent variable by which frequency should be measured.

A molecular dynamics (MD simulation on tire-aggregate friction

Directory of Open Access Journals (Sweden)

Fengyan Sun

2017-07-01

Full Text Available The friction between tire and road surface is fundamentally depending on the molecular forces. In this paper, the nanoscale 3D contact model is employed to investigate the tire-aggregate friction mechanism. The tire and aggregate micro-structure are both constructed to evaluate the microscopic performance of tire-aggregate friction influence. Simulation results show for a high velocity, the energy dissipation of sliding on crystal structure is small, which results in a small friction coefficient; temperature will have influences on the friction coefficient, and with the increasing of velocity, the effect will gradually reduce. Keywords: Tire, Aggregate, Friction coefficient, Microscopic mechanism, MD simulation

Impact of Advertising on Tampon Wear-time Practices.

Science.gov (United States)

Woeller, Kara E; Miller, Kenneth W; Robertson-Smith, Amy L; Bohman, Lisa C

2015-01-01

(1) To determine whether advertising nighttime tampon use for up to eight hours was understood to be consistent with label recommendations and (2) to determine whether television and print advertising with this message affected tampon wear times in adults and teens. (1) A comprehension study (online advertising and follow-up questionnaire) among women aged 14-49 years (300 per group) who viewed either the test or a control advertising message; (2) Diary-based surveys of tampon wear times performed prior to (n = 292 adults, 18-49 years, 74 teens, 12-17 years) and after (n = 287 adults, 104 teens) the launch of national advertising. Significantly more test message viewers than controls stated tampons should be worn less than or equal to eight hours (93.6% vs. 88.6%, respectively, P = 0.049). A directionally higher percentage of test message viewers said they would use a pad if sleeping longer than eight hours (52% vs. 42% of controls). Among the women who used tampons longer than eight hours when sleeping, 52% reported they would wake up and change compared with 45% of controls. No significant difference between baseline and follow-up diary surveys was found among teens or adults in various measures of tampon wear time (mean wear times; usage intervals from less than two hours to more than 10 hours; percentage of tampons used for more than or equal to eight hours; frequency of wearing at least one tampon more than eight hours). Advertising nighttime tampon wear for up to eight hours effectively communicated label recommendations but did not alter tampon wear times. The informational intervention had limited impact on established habits.

Leaching of DOC, DN, and inorganic constituents from scrap tires.

Science.gov (United States)

Selbes, Meric; Yilmaz, Ozge; Khan, Abdul A; Karanfil, Tanju

2015-11-01

One concern for recycle and reuse of scrap tires is the leaching of tire constituents (organic and inorganic) with time, and their subsequent potential harmful impacts in environment. The main objective of this study was to examine the leaching of dissolved organic carbon (DOC), dissolved nitrogen (DN), and selected inorganic constituents from scrap tires. Different sizes of tire chips and crumb rubber were exposed to leaching solutions with pH's ranging from 3.0 to 10.0 for 28days. The leaching of DOC and DN were found to be higher for smaller size tire chips; however, the leaching of inorganic constituents was independent of the size. In general, basic pH conditions increased the leaching of DOC and DN, whereas acidic pH conditions led to elevated concentrations of metals. Leaching was minimal around the neutral pH values for all the monitored parameters. Analysis of the leaching rates showed that components associated with the rubbery portion of the tires (DOC, DN, zinc, calcium, magnesium, etc.) exhibited an initial rapid followed by a slow release. On the other hand, a constant rate of leaching was observed for iron and manganese, which are attributed to the metal wires present inside the tires. Although the total amounts that leached varied, the observed leaching rates were similar for all tire chip sizes and leaching solutions. Operation under neutral pH conditions, use of larger size tire chips, prewashing of tires, and removal of metal wires prior to application will reduce the impact of tire recycle and reuse. Copyright © 2015 Elsevier Ltd. All rights reserved.

The in-plane deformation of a tire carcass: analysis and measurement

OpenAIRE

Xiong, Yi; Tuononen, Ari

2015-01-01

The deformation of parts of a tire is the direct result of tire–road interactions, and therefore is of great interest in tire sensor development. This case study focuses on the analysis of the deformation of the tire carcass and investigates its potential for the estimation of the in-plane tire force. The deformation of the tire carcass due to applied steady-state in-plane forces is first analyzed with the flexible ring model and then validated through optical tire sensor measurements. Couple...

Studded and unstudded winter tires in fatal road accidents in Finland.

Science.gov (United States)

Malmivuo, Mikko; Luoma, Juha; Porthin, Markus

2017-07-04

The aim of the study was to compare the safety effects of studded and unstudded winter tires based on fatal road accidents. The data included 958 road accidents involving a passenger car or van that occurred in Finland from November to March between 1997 and 2012. Comparing the proportions of winter tire type in accidents and in general traffic showed that the overall effect of tire type on the number of accidents was not significant, although studded tires reduced fatal accidents by 10-15%. Compared to unstudded tires, studded tires reduced accidents significantly only on bald ice in 2005-2012. Drivers using unstudded tires were more experienced and their profession was more frequently related to driving. In addition, the vehicle age was lower for vehicles with unstudded tires. On the other hand, the state of repair was less pertinent for unstudded than for studded tires. These confounding factors offset their effects to some degree. The risk of fatal road accidents in winter between studded and unstudded tires does not differ significantly. However, the accident risk has recently been substantially higher on bald ice for unstudded than for studded tires. The magnitude of this risk difference is difficult to determine without specific information on exposure by road surface.

Ground tire rubber as a stabilizer for subgrade soils.

Science.gov (United States)

2014-05-01

Over 250 million scrap tires are generated annually in the U.S. Historically, a significant portion of these tires : have been processed into finely ground tire rubber (GTR), or crumb rubber, for use as an additive in hot mix asphalt : (HMA) pavement...

Finite Element Modeling of an Aircraft Tire Rolling on a Steel Drum: Experimental Investigations and Numerical Simulations

Directory of Open Access Journals (Sweden)

Iulian Rosu

2018-04-01

Full Text Available The aim of this study is to investigate the thermal evolution of an aircraft tire rolling at high velocities up to take off values. As this kind of experiment is difficult to realize on a real runway, experimental tests were realized on aircraft tires rolling on a steel drum. The rotating drum facility allows to apply variable velocities beyond the take off limits, at fixed skidding angles and loadings. The rolling conditions, vertical loading, velocity and cornering conditions were adopted to correspond to the real conditions of an aircraft tire running or skidding on a flat runway. In the experimental part, the influence of skidding angle, velocity and loading on the thermal evolution of the tire tread were investigated. The thermo-mechanical finite element analysis of a pneumatic radial tire structure was performed taking into account the hyper-viscoelastic rubber behavior, with heating mechanisms developed by the inelastic deformation and by friction. Three-dimensional finite element simulations of an aircraft tire rolling on a steel drum were carried out using Abaqus/Standard finite element solver. The comparison of the temperature distribution on the tire tread between numerical results and the experimental data shows the same overall tendencies. The good correlation between numerical and experimental data shows that numerical simulation could predict the thermal evolution of the tire in critical situations. The authors would like to mention that for confidentiality reason, certain numerical data could not be revealed.

World's largest off-road tires to be recycled

Energy Technology Data Exchange (ETDEWEB)

Anon.

2005-07-01

Suncor Energy is the first company in Canada to use a new technology designed uniquely for tire recycling at oil sand facilities. The technology is owned by CuttingEdge Tire Recycling, a partnership between Denesoline Environmental Limited Partnership and Beaver Environmental Rubber Technologies Limited. Suncor has supported the development of this Aboriginal-owned and operated business by offering land, electricity, diesel fuel and stockpiles of used truck tires from its oil sand mining activities. These tires are the largest off-road tires in the world. In this new technology, tires that are worn-out through oil sand mining are shredded in a portable shredder before being recycled for subsequent use by the Alberta Recycling Management Association. 1 fig.

Static tests of constructive tires using hydraulic press on the soil

OpenAIRE

Machado,Thiago M.; Lanças,Kléber P.; Oliveira Junior,Mauro B. de; Artioli,José A.; Marasca,Indiamara

2015-01-01

ABSTRACT The power consumption and load capacity of agricultural machines have grown and the effects of pressure on the soil by tires have been still little investigated. In concern with sustainable development, the relationship machine-tire-soil must be in balance to give more consistency on the best use of tires for a given load. This study aimed to evaluate four tires of two constructive types, the bias belted tires and radial tires, both with respective rim diameters of 22.5 and 26.5 inch...

Fan-out Estimation in Spin-based Quantum Computer Scale-up.

Science.gov (United States)

Nguyen, Thien; Hill, Charles D; Hollenberg, Lloyd C L; James, Matthew R

2017-10-17

Solid-state spin-based qubits offer good prospects for scaling based on their long coherence times and nexus to large-scale electronic scale-up technologies. However, high-threshold quantum error correction requires a two-dimensional qubit array operating in parallel, posing significant challenges in fabrication and control. While architectures incorporating distributed quantum control meet this challenge head-on, most designs rely on individual control and readout of all qubits with high gate densities. We analysed the fan-out routing overhead of a dedicated control line architecture, basing the analysis on a generalised solid-state spin qubit platform parameterised to encompass Coulomb confined (e.g. donor based spin qubits) or electrostatically confined (e.g. quantum dot based spin qubits) implementations. The spatial scalability under this model is estimated using standard electronic routing methods and present-day fabrication constraints. Based on reasonable assumptions for qubit control and readout we estimate 10 2 -10 5 physical qubits, depending on the quantum interconnect implementation, can be integrated and fanned-out independently. Assuming relatively long control-free interconnects the scalability can be extended. Ultimately, the universal quantum computation may necessitate a much higher number of integrated qubits, indicating that higher dimensional electronics fabrication and/or multiplexed distributed control and readout schemes may be the preferredstrategy for large-scale implementation.

Assessing the impact of model spin-up on surface water-groundwater interactions using an integrated hydrologic model

KAUST Repository

Ajami, Hoori; McCabe, Matthew; Evans, Jason P.; Stisen, Simon

2014-01-01

is to minimize the impact of initialization while using the smallest spin-up time possible. In this study, multicriteria analysis was performed to assess the spin-up behavior of the ParFlow.CLM integrated groundwater-surface water-land surface model over a 208 km

76 FR 79114 - Tire Fuel Efficiency Consumer Information Program

Science.gov (United States)

2011-12-21

... car tires. The final rule also established reporting requirements for the generated performance... aspects of tire performance: rolling resistance, wet traction, and treadwear life.\\3\\ The final rule also... provide information indicating the relative performance of passenger car tires in the areas of treadwear...

75 FR 15893 - Tire Fuel Efficiency Consumer Information Program

Science.gov (United States)

2010-03-30

... how much the proposed consumer information program would affect consumer tire purchasing behavior and... 575 Tire Fuel Efficiency Consumer Information Program; Final Rule #0;#0;Federal Register / Vol. 75, No... 2127-AK45 Tire Fuel Efficiency Consumer Information Program AGENCY: National Highway Traffic Safety...

Three Three-Axis IEPE Accelerometers on the Inner Liner of a Tire for Finding the Tire-Road Friction Potential Indicators

Directory of Open Access Journals (Sweden)

Arto Niskanen

2015-08-01

Full Text Available Direct tire-road contact friction estimation is essential for future autonomous cars and active safety systems. Friction estimation methods have been proposed earlier for driving conditions in the presence of a slip angle or slip ratio. However, the estimation of the friction from a freely-rolling tire is still an unsolved topic. Knowing the existing friction potential would be beneficial since vehicle control systems could be adjusted before any remarkable tire force has been produced. Since accelerometers are well-known and robust, and thus a promising sensor type for intelligent tires, this study uses three three-axis IEPE accelerometers on the inner liner of a tire to detect friction potential indicators on two equally smooth surfaces with different friction levels. The equal roughness was chosen for both surfaces in order to study the friction phenomena by neglecting the effect of surface texture on vibrations. The acceleration data before the contact is used to differentiate the two friction levels between the tire and the road. In addition, the contact lengths from the three accelerometers are used to validate the acceleration data. A method to differentiate the friction levels on the basis of the acceleration signal is also introduced.

Detection of tire tread particles using laser-induced breakdown spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Prochazka, David, E-mail: prochazka.d@fme.vutbr.cz [Brno University of Technology, Institute of Physical Engineering, Technická 2, 616 00 Brno (Czech Republic); Brno University of Technology, Central European Institute of Technology, Technická 3058/10, CZ-616 00 Brno (Czech Republic); Bilík, Martin [Brno University of Technology, Institute of Forensic Engineering, Údolní 244/53, 602 00 Brno (Czech Republic); Prochazková, Petra [Masaryk University, Faculty of Science, Department of Chemistry, Kamenice 735/5, 625 00 Brno (Czech Republic); Klus, Jakub; Pořízka, Pavel; Novotný, Jan [Brno University of Technology, Central European Institute of Technology, Technická 3058/10, CZ-616 00 Brno (Czech Republic); Novotný, Karel [Masaryk University, Faculty of Science, Department of Chemistry, Kamenice 735/5, 625 00 Brno (Czech Republic); Brno University of Technology, Central European Institute of Technology, Technická 3058/10, CZ-616 00 Brno (Czech Republic); Ticová, Barbora [Masaryk University, Faculty of Science, Department of Chemistry, Kamenice 735/5, 625 00 Brno (Czech Republic); Bradáč, Albert; Semela, Marek [Brno University of Technology, Institute of Forensic Engineering, Údolní 244/53, 602 00 Brno (Czech Republic); and others

2015-06-01

The objective of this paper is a study of the potential of laser induced breakdown spectroscopy (LIBS) for detection of tire tread particles. Tire tread particles may represent pollutants; simultaneously, it is potentially possible to exploit detection of tire tread particles for identification of optically imperceptible braking tracks at locations of road accidents. The paper describes the general composition of tire treads and selection of an element suitable for detection using the LIBS method. Subsequently, the applicable spectral line is selected considering interferences with lines of elements that might be present together with the detected particles, and optimization of measurement parameters such as incident laser energy, gate delay and gate width is performed. In order to eliminate the matrix effect, measurements were performed using 4 types of tires manufactured by 3 different producers. An adhesive tape was used as a sample carrier. The most suitable adhesive tape was selected from 5 commonly available tapes, on the basis of their respective LIBS spectra. Calibration standards, i.e. an adhesive tape with different area content of tire tread particles, were prepared for the selected tire. A calibration line was created on the basis of the aforementioned calibration standards. The linear section of this line was used for determination of the detection limit value applicable to the selected tire. Considering the insignificant influence of matrix of various types of tires, it is possible to make a simple recalculation of the detection limit value on the basis of zinc content in a specific tire. - Highlights: • LIBS experimental measurement parameters for tire tread particles were optimize. • Calibration curve was prepared. • Limit of detection was determined.

Detection of tire tread particles using laser-induced breakdown spectroscopy

International Nuclear Information System (INIS)

Prochazka, David; Bilík, Martin; Prochazková, Petra; Klus, Jakub; Pořízka, Pavel; Novotný, Jan; Novotný, Karel; Ticová, Barbora; Bradáč, Albert; Semela, Marek

2015-01-01

The objective of this paper is a study of the potential of laser induced breakdown spectroscopy (LIBS) for detection of tire tread particles. Tire tread particles may represent pollutants; simultaneously, it is potentially possible to exploit detection of tire tread particles for identification of optically imperceptible braking tracks at locations of road accidents. The paper describes the general composition of tire treads and selection of an element suitable for detection using the LIBS method. Subsequently, the applicable spectral line is selected considering interferences with lines of elements that might be present together with the detected particles, and optimization of measurement parameters such as incident laser energy, gate delay and gate width is performed. In order to eliminate the matrix effect, measurements were performed using 4 types of tires manufactured by 3 different producers. An adhesive tape was used as a sample carrier. The most suitable adhesive tape was selected from 5 commonly available tapes, on the basis of their respective LIBS spectra. Calibration standards, i.e. an adhesive tape with different area content of tire tread particles, were prepared for the selected tire. A calibration line was created on the basis of the aforementioned calibration standards. The linear section of this line was used for determination of the detection limit value applicable to the selected tire. Considering the insignificant influence of matrix of various types of tires, it is possible to make a simple recalculation of the detection limit value on the basis of zinc content in a specific tire. - Highlights: • LIBS experimental measurement parameters for tire tread particles were optimize. • Calibration curve was prepared. • Limit of detection was determined

Stability Control of Vehicle Emergency Braking with Tire Blowout

OpenAIRE

Chen, Qingzhang; Liu, Youhua; Li, Xuezhi

2014-01-01

For the stability control and slowing down the vehicle to a safe speed after tire failure, an emergency automatic braking system with independent intellectual property is developed. After the system has received a signal of tire blowout, the automatic braking mode of the vehicle is determined according to the position of the failure tire and the motion state of vehicle, and a control strategy for resisting tire blowout additional yaw torque and deceleration is designed to slow down vehicle to...

Study on profile measurement of extruding tire tread by laser

Science.gov (United States)

Wang, LiangCai; Zhang, Wanping; Zhu, Weihu

1996-10-01

This paper presents a new 2D measuring system-profile measurement of extruding tire tread by laser. It includes the thickness measurement of extruding tire tread by laser and the width measurement of extruding tire tread using Moire Fringe. The system has been applied to process line of extruding tire tread. Two measuring results have been obtained. One is a standard profile picture of extruding tire tread including seven measuring values. Another one is a series of thickness and width values. When the scanning speed thickness range is thickness < +/- 0.1mm.

Potential to use waste tires as supplemental fuel in pulp and paper mill boilers, cement kilns and in road pavement

Energy Technology Data Exchange (ETDEWEB)

Barlaz, M.A.; Eleazer, W.E. II (North Carolina State Univ., Raleigh, NC (United States). Dept. of Civil Engineering); Whittle, D.J.

1993-12-01

The objective of this paper is to evaluate the recycling potential of waste tires as an energy source and for use in road pavement. North Carolina, U.S.A., is used as a case study. Scrap tires may be burned for supplemental fuel in pulp and paper mill boilers and cement kilns. Five pulp and paper mill boilers in North Carolina could consume over 90% of the 6 million tires generated annually in the state. Cement kilns located within 400 km of North Carolina population centers could consume about 6.6 million tires annually. Based on the quantity of pavement laid in North Carolina, non-proprietary and proprietary versions of asphalt rubber concrete have the potential to consume 1.8 and 7.2 million tires, respectively. Rubber modified asphalt concrete has the potential to consume up to 16.5 million tires. However, technological and economic limitations suggest that large scale implementation is unlikely for the short term. Environmental considerations pertaining to each alternative are discussed. (author)

Tire containing thermally exfoliated graphite oxide

Science.gov (United States)

Prud'homme, Robert K. (Inventor); Aksay, Ilhan A. (Inventor)

2011-01-01

A tire, tire lining or inner tube, containing a polymer composite, made of at least one rubber and/or at least one elastomer and a modified graphite oxide material, which is a thermally exfoliated graphite oxide with a surface area of from about 300 sq m/g to 2600 sq m/g.

A Planar Quasi-Static Constraint Mode Tire Model

Science.gov (United States)

2015-07-10

strikes a balance between simple tire models that lack the fidelity to make accurate chassis load predictions and computationally intensive models that...strikes a balance between heuristic tire models (such as a linear point-follower) that lack the fidelity to make accurate chassis load predictions...UNCLASSIFIED: Distribution Statement A. Cleared for public release A PLANAR QUASI-STATIC CONSTRAINT MODE TIRE MODEL Rui Maa John B. Ferris

Elastomers in Combined Rolling-Sliding Contact; Wear and its Underlying Mechanisms

Science.gov (United States)

Rowe, Kyle Gene

Elastomeric materials, specifically rubbers, being both of a practical and scientific importance, have been the subjects of vast amounts of research spanning well over two centuries. There is currently a large effort by tire manufacturers to design new rubber compounds with lower rolling resistance, higher sliding friction, and reduced or predictable wear. At present, these efforts are primarily based on a few empirical rules and very costly trial and error testing; only a basic understanding of the mechanisms involved in the wear of elastomeric materials exists despite rigorous study. In general, the only well controlled experiments have been for simple loading and sliding schemes. The aim of this work is to characterize the tribological properties of a carbon black filled natural rubber sample. This work explores (1) its behavior in unidirectional sliding, (2) contact mechanics, (3) traction properties in combined rolling and sliding, (4) frictional heating response, and (5) wear. It was found that the friction coefficient of this material was dependent upon sliding velocity, contact pressure, and surface roughness. The high friction coefficients also lead to a bifurcation of the contact area into two different pressure regimes at sliding velocities greater than 10 mm/s . The traction response of this material in combined rolling and sliding exhibited similar behavior, being a function of the contact pressure, but not rolling velocity. The wear of this material was found to be linearly dependent upon the global slip condition and occurred preferentially on the sample. Investigations of the worn surface revealed that the most likely mechanism of wear is the degradation of surface material in a confined layer a few micrometers thick. A simple spring-mass model was developed to offer an explanation of localized wear. It was found that the coupling of system elements in the normal direction helped to shift the load from wearing elements to non-wearing ones. The

Impact of Advertising on Tampon Wear-time Practices

Directory of Open Access Journals (Sweden)

Kara E. Woeller

2015-01-01

Full Text Available Objectives (1 To determine whether advertising nighttime tampon use for up to eight hours was understood to be consistent with label recommendations and (2 to determine whether television and print advertising with this message affected tampon wear times in adults and teens. Methods (1 A comprehension study (online advertising and follow-up questionnaire among women aged 14–49 years (300 per group who viewed either the test or a control advertising message; (2 Diary-based surveys of tampon wear times performed prior to ( n = 292 adults, 18–49 years, 74 teens, 12–17 years and after ( n = 287 adults, 104 teens the launch of national advertising. Results Significantly more test message viewers than controls stated tampons should be worn less than or equal to eight hours (93.6% vs. 88.6%, respectively, P = 0.049. A directionally higher percentage of test message viewers said they would use a pad if sleeping longer than eight hours (52% vs. 42% of controls. Among the women who used tampons longer than eight hours when sleeping, 52% reported they would wake up and change compared with 45% of controls. No significant difference between baseline and follow-up diary surveys was found among teens or adults in various measures of tampon wear time (mean wear times; usage intervals from less than two hours to more than 10 hours; percentage of tampons used for more than or equal to eight hours; frequency of wearing at least one tampon more than eight hours. Conclusions Advertising nighttime tampon wear for up to eight hours effectively communicated label recommendations but did not alter tampon wear times. The informational intervention had limited impact on established habits.

New developments in tire derived fuels (TDF)

Energy Technology Data Exchange (ETDEWEB)

Hawkins, G. [Portland Cement Association, Skokie, IL (United States)

2006-07-01

Portland cement is a mixture of finely ground raw materials that are processed in a rotary kiln heated to 1500 degrees C by various fuels. Cooled clinker from the kiln is ground into portland cement. This presentation provided an overview of the role that tire-derived fuels is now playing in cement manufacturing. Data on the extent of TDF use in cement manufacturing processes were presented, as well as the results of air emissions monitoring programs conducted to assess the environmental impacts of TDF. During the cement manufacturing process, shredded and chipped tires are blown into the kiln to provide fuel, while whole tires are placed in the midpoint of long dry or wet kilns. For preheater and precalciner kilns, whole tires are added to raw material entering the kiln. The kiln's controlled combustion environment ensures the complete destruction of scrap tires. Approximately 130 million scrap tires were recycled in Portland cement plants in 2003. Forty-four portland cement plants are currently using TDF in North America. The United States Department of Energy has estimated that TDF produces less carbon dioxide (CO{sub 2}) per unit of energy than coal. Monitoring programs at Portland cement plants have indicated that the use of TDF in place of coal has resulted in moderate reductions of nitrogen oxide (NO{sub x}) emissions, slightly lower sulfuric oxide (SO{sub 2}) emissions and moderate reductions in carbon monoxide (CO). Some plants have reported slight reductions in particulate matter (PM) emissions. It was concluded that the use of scrap tires as a fuel reduces a waste stream and contributes to energy and raw material requirements. Moreover, plant air emissions are either reduced or are not impacted by TDF use. refs., tabs., figs.

Optimal tread design for agricultural lug tires determined through failure analysis

Directory of Open Access Journals (Sweden)

Hyun Seok Song

2018-04-01

Full Text Available Agricultural lug tires, commonly used in tractors, must provide safe and stable support for the body of the vehicle and bear any additional load while effectively traversing rough, poor-quality ground surfaces. Many agricultural lug tires fail unexpectedly. In this study, we optimised and validated a tread design for agricultural lug tires intended to increase their durability using failure analysis. Specifically, we identified tire failure modes using indoor driving tests and failure mode effects analysis. Next, we developed a threedimensional tire model using the Ogden material model and finite element method. Using sensitivity analysis and response surface methodology, we optimised the tread design. Finally, we evaluated the durability of the new design using a tire prototype and drum test equipment. Results indicated that the optimised tread design decreased the tire tread stress by 16% and increased its time until cracking by 38% compared to conventional agricultural lug tires.

USING THE SCRAP TIRES TO PRODUCE A FLEXIBLE COUPLER

OpenAIRE

Tahsean A. Hussain

2018-01-01

The scrap tires considered a problematic source of waste, the old rubber tires causes a big environmental problem that is need much money and effort to disposes it safely. In Iraq there are more than two million used tires disposed to the environment annually. one of the tire’s recycling methods is the use of tire layers to produce a new rubber parts used in the engineering and industrial purposes as the bridges and machines dampers, this trend of recycling doesn’t take a sufficient care comp...

USING THE SCRAP TIRES TO PRODUCE A FLEXIBLE COUPLER

Directory of Open Access Journals (Sweden)

Tahsean A. Hussain

2018-01-01

Full Text Available The scrap tires considered a problematic source of waste, the old rubber tires causes a big environmental problem that is need much money and effort to disposes it safely. In Iraq there are more than two million used tires disposed to the environment annually. one of the tire’s recycling methods is the use of tire layers to produce a new rubber parts used in the engineering and industrial purposes as the bridges and machines dampers, this trend of recycling doesn’t take a sufficient care comparing with the other uses. There are a lot of studies conducted in these field, these studies suggests many methods to manage the huge number of scrap tires, the current paper aims to use the old rubber tires in engineering purposes (especially as a coupler joins the motor or engines with the other equipment as electric dynamo or pumps, the study focusing on the mechanical properties of a strip from a used tires and comparing with one prepared in the lab., and suggesting a new method to use as an engineering parts (for example the coupler lays between the IC engine and the dynamo of an electric generator. One of the results obtained from the experiments, there is no significant difference between the mechanical properties of the old and the new strip, (in the tensile test, the breaking force of the -Lab. tensile specimen- is 137 N whereas the specimen of old tire have a breaking force 113.27 N, but they are same in the elongation. A computational example is suggested to estimate the dimensions of a flexible coupler use an old tire pieces.

Dynamic tire pressure sensor for measuring ground vibration.

Science.gov (United States)

Wang, Qi; McDaniel, James Gregory; Wang, Ming L

2012-11-07

This work presents a convenient and non-contact acoustic sensing approach for measuring ground vibration. This approach, which uses an instantaneous dynamic tire pressure sensor (DTPS), possesses the capability to replace the accelerometer or directional microphone currently being used for inspecting pavement conditions. By measuring dynamic pressure changes inside the tire, ground vibration can be amplified and isolated from environmental noise. In this work, verifications of the DTPS concept of sensing inside the tire have been carried out. In addition, comparisons between a DTPS, ground-mounted accelerometer, and directional microphone are made. A data analysis algorithm has been developed and optimized to reconstruct ground acceleration from DTPS data. Numerical and experimental studies of this DTPS reveal a strong potential for measuring ground vibration caused by a moving vehicle. A calibration of transfer function between dynamic tire pressure change and ground acceleration may be needed for different tire system or for more accurate application.

Preliminary measurements on heat balance in pneumatic tires

Science.gov (United States)

Nybakken, G. H.; Collart, D. Y.; Staples, R. J.; Lackey, J. I.; Clark, S. K.; Dodge, R. N.

1973-01-01

A variety of tests was undertaken to determine the nature of heat generation associated with a pneumatic tire operating under various conditions. Tests were conducted to determine the magnitude and distribution of internally generated heat caused by hysteresis in the rubber and ply fabric in an automobile tire operating under conditions of load, pressure, and velocity representative of normal operating conditions. These included tests at various yaw angles and tests with braking applied. In other tests, temperature sensors were mounted on a road to measure the effect of a tire rolling over and an attempt was made to deduce the magnitude and nature of interfacial friction from the resulting information. In addition, tests were performed using the scratch plate technique to determine the nature of the motion between the tire and road. Finally, a model tire was tested on a roadwheel, the surface covering which could be changed, and an optical pyrometer was used to measure rubber surface temperatures.

Mixing in thermally stratified nonlinear spin-up with uniform boundary fluxes

International Nuclear Information System (INIS)

Baghdasarian, Meline; Pacheco-Vega, Arturo; Pacheco, J. Rafael; Verzicco, Roberto

2014-01-01

Studies of stratified spin-up experiments in enclosed cylinders have reported the presence of small pockets of well-mixed fluids but quantitative measurements of the mixedness of the fluid has been lacking. Previous numerical simulations have not addressed these measurements. Here we present numerical simulations that explain how the combined effect of spin-up and thermal boundary conditions enhances or hinders mixing of a fluid in a cylinder. The energy of the system is characterized by splitting the potential energy into diabatic and adiabatic components, and measurements of efficiency of mixing are based on both, the ratio of dissipation of available potential energy to forcing and variance of temperature. The numerical simulations of the Navier–Stokes equations for the problem with different sets of thermal boundary conditions at the horizontal walls helped shed some light on the physical mechanisms of mixing, for which a clear explanation was absent

Mixing in thermally stratified nonlinear spin-up with uniform boundary fluxes

Energy Technology Data Exchange (ETDEWEB)

Baghdasarian, Meline; Pacheco-Vega, Arturo [Department of Mechanical Engineering, California State University, Los Angeles, Los Angeles, California 90032 (United States); Pacheco, J. Rafael, E-mail: rpacheco@asu.edu [SAP Americas Inc., Scottsdale, Arizona 85251 (United States); School of Mathematical and Statistical Sciences, Arizona State University, Tempe, Arizona 85287 (United States); Environmental Fluid Dynamics Laboratories, Department of Civil Engineering and Geological Sciences, The University of Notre Dame, South Bend, Indiana 46556 (United States); Verzicco, Roberto [Dipartimento di Ingegneria Meccanica, Universita di Roma “Tor Vergata”, Via del Politecnico 1, 00133, Roma (Italy); PoF, University of Twente, 7500 AE Enschede (Netherlands)

2014-09-15

Studies of stratified spin-up experiments in enclosed cylinders have reported the presence of small pockets of well-mixed fluids but quantitative measurements of the mixedness of the fluid has been lacking. Previous numerical simulations have not addressed these measurements. Here we present numerical simulations that explain how the combined effect of spin-up and thermal boundary conditions enhances or hinders mixing of a fluid in a cylinder. The energy of the system is characterized by splitting the potential energy into diabatic and adiabatic components, and measurements of efficiency of mixing are based on both, the ratio of dissipation of available potential energy to forcing and variance of temperature. The numerical simulations of the Navier–Stokes equations for the problem with different sets of thermal boundary conditions at the horizontal walls helped shed some light on the physical mechanisms of mixing, for which a clear explanation was absent.

Restorative Management of Severe Localized Tooth Wear Using a Supraoccluding Appliance: A 5-Year Follow-Up

Directory of Open Access Journals (Sweden)

Tsz Leung Wong

2018-01-01

Full Text Available This case report illustrates a novel conservative restorative management of a patient with bulimia nervosa who presented with severe localized upper palatal tooth wear and an anterior reverse overjet. This was achieved by using a localized bite raising or supraoccluding appliance, cemented on the lingual side of the lower anterior teeth to create interocclusal space, obviating the need for tooth reduction of the eroded upper palatal and incisal tooth surfaces. Surgical crown lengthening was performed to create a better aesthetic gingival architecture. All-ceramic restorations were provided on the upper anterior teeth to restore the tooth surface loss and provide a positive overbite and overjet. There was no complication or other observable biological change detected at the 5-year follow-up. The use of an appliance applying the supraoccluding technique, or Dahl concept, is a safe, conservative, and useful treatment option in the management of localized tooth wear.

Tooth wear and wear investigations in dentistry.

Science.gov (United States)

Lee, A; He, L H; Lyons, K; Swain, M V

2012-03-01

Tooth wear has been recognised as a major problem in dentistry. Epidemiological studies have reported an increasing prevalence of tooth wear and general dental practitioners see a greater number of patients seeking treatment with worn dentition. Although the dental literature contains numerous publications related to management and rehabilitation of tooth wear of varying aetiologies, our understanding of the aetiology and pathogenesis of tooth wear is still limited. The wear behaviour of dental biomaterials has also been extensively researched to improve our understanding of the underlying mechanisms and for the development of restorative materials with good wear resistance. The complex nature of tooth wear indicates challenges for conducting in vitro and in vivo wear investigations and a clear correlation between in vitro and in vivo data has not been established. The objective was to critically review the peer reviewed English-language literature pertaining to prevalence and aetiology of tooth wear and wear investigations in dentistry identified through a Medline search engine combined with hand-searching of the relevant literature, covering the period between 1960 and 2011. © 2011 Blackwell Publishing Ltd.

Indirect Tire Monitoring System - Machine Learning Approach

Science.gov (United States)

Svensson, O.; Thelin, S.; Byttner, S.; Fan, Y.

2017-10-01

The heavy vehicle industry has today no requirement to provide a tire pressure monitoring system by law. This has created issues surrounding unknown tire pressure and thread depth during active service. There is also no standardization for these kind of systems which means that different manufacturers and third party solutions work after their own principles and it can be hard to know what works for a given vehicle type. The objective is to create an indirect tire monitoring system that can generalize a method that detect both incorrect tire pressure and thread depth for different type of vehicles within a fleet without the need for additional physical sensors or vehicle specific parameters. The existing sensors that are connected communicate through CAN and are interpreted by the Drivec Bridge hardware that exist in the fleet. By using supervised machine learning a classifier was created for each axle where the main focus was the front axle which had the most issues. The classifier will classify the vehicles tires condition and will be implemented in Drivecs cloud service where it will receive its data. The resulting classifier is a random forest implemented in Python. The result from the front axle with a data set consisting of 9767 samples of buses with correct tire condition and 1909 samples of buses with incorrect tire condition it has an accuracy of 90.54% (0.96%). The data sets are created from 34 unique measurements from buses between January and May 2017. This classifier has been exported and is used inside a Node.js module created for Drivecs cloud service which is the result of the whole implementation. The developed solution is called Indirect Tire Monitoring System (ITMS) and is seen as a process. This process will predict bad classes in the cloud which will lead to warnings. The warnings are defined as incidents. They contain only the information needed and the bandwidth of the incidents are also controlled so incidents are created within an

Development of tire road noise chassis-dynamometer simulator. Effect of ISO surface replica model pad on tire road noise; Shisakushita tire romen soon shiken`yo jissha daijo simulator ni tsuite. ISO romen mogi pad wo sochakushita koka ni kansuru kisoteki kento

Energy Technology Data Exchange (ETDEWEB)

Tanaka, T; Murakami, T; Ogata, S; Sakamoto, I [Traffic Safety and Nuisance Research Inst., Tokyo (Japan)

1997-10-01

As a new test facility to clarify noise reduction method of tire road noise, Tire Road Noise Chassis-Dynamometer Simulator was developed. ISO surface replica pads made by copying the texture of ISO surface were attached on the roller surface of this system to simulate tire road noise. This paper described the specifications and characteristics of this system, and the effects of ISO surface replica pads on tire noise measurement by comparing the sound intensity in horizontal plane of tire noise measured in this system with that measured in a single drum tester with safety walk surface. 4 refs., 10 figs., 1 tab.

Final Scientific Report - "Improved Fuel Efficiency from Nanocomposite Tire Tread"

Energy Technology Data Exchange (ETDEWEB)

Dr. Andrew Myers

2005-12-30

Rolling resistance, a measure of the energy lost as a tire rotates while moving, is a significant source of power and fuel loss. Recently, low rolling resistant tires have been formulated by adding silica to tire tread. These "Green Tires" (so named from the environmental advantages of lower emissions and improved fuel economy) have seen some commercial success in Europe, where high fuel prices and performance drive tire selection. Unfortunately, the higher costs of the silica and a more complicated manufacturing process have prevented significant commercialization - and the resulting fuel savings - in the U.S. In this project, TDA Research, Inc. (TDA) prepared an inexpensive alternative to silica that leads to tire components with lower rolling resistance. These new tire composite materials were processed with traditional rubber processing equipment. We prepared specially designed nanoparticle additives, based on a high purity, inorganic mineral whose surface can be easily modified for compatibility with tire tread formulations. Our nanocomposites decreased energy losses to hysteresis, the loss of energy from the compression and relaxation of an elastic material, by nearly 20% compared to a blank SBR sample. We also demonstrated better performance than a leading silica product, with easier production of our final rubber nanocomposite.

Wear reduction through piezoelectrically-assisted ultrasonic lubrication

International Nuclear Information System (INIS)

Dong, Sheng; J Dapino, Marcelo

2014-01-01

Traditional lubricants are undesirable in harsh aerospace environments and certain automotive applications. Ultrasonic vibrations can be used to reduce and modulate the effective friction coefficient between two sliding surfaces. This paper investigates the relationship between friction force reduction and wear reduction in ultrasonically lubricated surfaces. A pin-on-disc tribometer is modified through the addition of a piezoelectric transducer which vibrates the pin at 22 kHz in the direction perpendicular to the rotating disc surface. Friction and wear metrics including volume loss, surface roughness, friction forces and apparent stick-slip effects are measured without and with ultrasonic vibrations at three different sliding velocities. SEM imaging and 3D profilometry are used to characterize the wear surfaces and guide model development. Over the range of speeds considered, ultrasonic vibrations reduce the effective friction force up to 62% along with a wear reduction of up to 49%. A simple cube model previously developed to quantify friction force reduction is implemented which describes wear reduction within 15% of the experimental data. (paper)

Measuring service life and evaluating the quality of solid tires

Directory of Open Access Journals (Sweden)

Charoenyut Dechwayukul

2010-08-01

Full Text Available The objective of this research is to propose procedures for measuring service life and evaluating the quality of locallymade and used solid tires in Thailand. The solid tires were stressed and rotated until blowout on a drum-like test apparatuswhich is designed, constructed by the authors and equipped with laboratory instrumentation. Solid tires from five differentmanufacturers were selected for testing. We measured service life, length of time to tire failure, at three different loadingamplitudes and three different speeds on the testing drum. The service life of all specimens was studied and compared todetermine the possibility of using service life to evaluate the quality of a solid tire.

Properties of tire rubber with zinc-containing technological additives

Directory of Open Access Journals (Sweden)

S. N. Kayushnikov

2017-01-01

Full Text Available In this paper, we studied the influence of zinc-containing technological additives on partial replacement of zinc oxide and stearic acid on deformation-strength and performance properties of tire elastomeric compositions based on polyisoprene rubber and combination of oil-filled butadiene-styrene and polybutadiene rubbers. It was revealed that partial replacement of zinc oxide and stearic acid with zinc-containing technological additives does not significantly affect the basic physico-mechanical properties of rubbers based on synthetic rubbers of general use. It was determined that the introduction of zinc-containing technological additives SCC2 in combination with zinc oxide in all the studied ratios and SCC3 in combination with zinc oxide in 4: 1 and 3: 1 ratios leads to increase (up to 10.4% of the resistance of these rubbers under the action of temperature-force fields, which is probably due to a more even distribution of polar components of curing system in non-polar elastomeric matrix, as well as the type of cross-links formed during vulcanization under the action of surface-active additives. It has been found that the introduction of zinc-containing additives into the elastomeric compositions based on SRMS-30 ARKM-15 + SRD in combination with zinc oxide leads to increase to 6.3% of wear resistance of rubbers, which may be due to a lower defectiveness of vulcanization structure of these rubbers, concentration of stress centers in the material. For rubbers based on SRI-3, preservation of bond strength of rubber with a textile cord at a sufficiently high level is shown.

26 CFR 48.4071-4 - Original equipment tires on imported articles.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 16 2010-04-01 2010-04-01 true Original equipment tires on imported articles..., Tread Rubber, and Taxable Fuel Tires, Tubes, and Tread Rubber § 48.4071-4 Original equipment tires on... than bicycle tires and inner tubes) that are original equipment for an imported article upon which no...

Photocatalytic Desulfurization of Waste Tire Pyrolysis Oil

Directory of Open Access Journals (Sweden)

Napida Hinchiranan

2011-11-01

Full Text Available Waste tire pyrolysis oil has high potential to replace conventional fossil liquid fuels due to its high calorific heating value. However, the large amounts of sulfurous compounds in this oil hinders its application. Thus, the aim of this research was to investigate the possibility to apply the photo-assisted oxidation catalyzed by titanium dioxide (TiO2, Degussa P-25 to partially remove sulfurous compounds in the waste tire pyrolysis oil under milder reaction conditions without hydrogen consumption. A waste tire pyrolysis oil with 0.84% (w/w of sulfurous content containing suspended TiO2 was irradiated by using a high-pressure mercury lamp for 7 h. The oxidized sulfur compounds were then migrated into the solvent-extraction phase. A maximum % sulfur removal of 43.6% was achieved when 7 g/L of TiO2 was loaded into a 1/4 (v/v mixture of pyrolysis waste tire oil/acetonitrile at 50 °C in the presence of air. Chromatographic analysis confirmed that the photo-oxidized sulfurous compounds presented in the waste tire pyrolysis oil had higher polarity, which were readily dissolved and separated in distilled water. The properties of the photoxidized product were also reported and compared to those of crude oil.

Pneumatic Tire Performance on Ice

OpenAIRE

Kishore Bhoopalam, Anudeep

2015-01-01

The evolution of vehicle safety systems, from the earliest brakes to today's accident avoidance systems, has led vehicles to have very high passenger safety. Driving on ice, though, still happens to be one of the driving conditions of low safety. A multitude of factors were identified by various studies to contribute to the complex frictional mechanism at the tire-ice interface. The tire is only force transmitting element of the vehicle, to the surface. Thus it is very essential to have in de...

Distribution of sulphur into products from waste tire pyrolysis

International Nuclear Information System (INIS)

Susa, D.; Haydary, J.; Markos, J.

2012-01-01

Tire pyrolysis is getting growing attention as an effective waste tire disposal method in comparison to environmentally less friendly methods like dumping or incineration. But the scrap tire sulphur content can be a potential obstacle to scrap tire utilization as a fuel. In this paper the distribution of sulphur into tire pyrolysis yields, solid (char) and liquid (tar), was investigated. The pyrolysis experiments were carried out under different conditions to determine the partitioning of sulphur into pyrolysis products. The influence of different temperatures and reaction times was investigated in a laboratory flow reactor under nitrogen atmosphere. Solid and liquid residues were collected and analyzed by elemental analysis. The sulphur content in residual char and tar was determined using an elemental analyzer and the sulphur forms in tar were characterized by the X-ray photoelectron spectroscopy (XPS). (Authors)

COMPUTATIONAL AND EXPERIMENTAL EVALUATION OF TECHNICAL CHARACTERISTICS OF TRUCKS TIRES

Directory of Open Access Journals (Sweden)

Z. A. Godzhaev

2015-01-01

Full Text Available Now improvement of technological design specification of trucks tires develops very much. In modern mechanical engineering polyamide and kapron cords for tires of line-haul trucks and buses are replaced with all-metal ones (AMC even more often. It was defined that at increase in AMC tires production their technical characteristics were investigated insufficiently. In this regard there were carried out bench tests to compare the main operational indicators of domestic (JSC Nizhnekamskshina production and foreign tires with an all-metal cord: 315/60R22.5 the NF-201 model with 315/60r22.5 the XZA2 ENERGY Michelin model (steering; 315/60R22.5 the NR-201 model with 315/60R22.5 the XDA2+ ENERGY Michelin model (drive; 315/80R22.5 the NF-201 model with 315/80R22.5 the 3D Michelin XZE X MultiWay model (steering; 315/80R22.5 the NR-201 model with 315/80R22.5 the 3D XDE X MultiWay model (drive. The laboratory researches were carried out for the purpose of an assessment of the universal, load, damping (hysteresis and other characteristics of tires with use of the universal functional SIB-1M test-bench. It was established that Michelin AMC tires of steering low-profile 315/60R22.5 XZA2 ENERGY models have the best indicators on power heterogeneity - 0.47-0.89 percent. The high-profile AMC tires of drive wheels 315/80R22.5 of the NR-201 model of JSC Nizhnekamskshina have the worst indicators. However, all the tested tires correspond to GOST 5513-97on this indicator. It was noted that Nizhnekamsk AMC tires of the size 315/60R22.5 are flush with AMC tires Michelin on set of operational indicators, except power heterogeneity, and last one of Michelin tires is lower than Nizhnekamsk ones by 2-3 times. It was suggested to conduct further researches on definition of optimum operational tires indicators because of an intensive use of KAMAZ trucks in agricultural production

Ground tire rubber as a stabilizer for subgrade soils : [summary].

Science.gov (United States)

2014-05-01

Over 250 million scrap tires are generated : annually in the U.S. Historically, a significant : portion of these tires have been processed into : finely ground tire rubber (GTR), or crumb rubber, : for use as an additive in hot mix asphalt (HMA) : pa...

T.R.I.C.K.-Tire/Road Interaction Characterization & Knowledge - A tool for the evaluation of tire and vehicle performances in outdoor test sessions

Science.gov (United States)

Farroni, Flavio

2016-05-01

The most powerful engine, the most sophisticated aerodynamic devices or the most complex control systems will not improve vehicle performances if the forces exchanged with the road are not optimized by proper employment and knowledge of tires. The vehicle interface with the ground is constituted by the sum of small surfaces, wide about as one of our palms, in which tire/road interaction forces are exchanged. From this it is clear to see how the optimization of tire behavior represents a key-factor in the definition of the best setup of the whole vehicle. Nowadays, people and companies playing a role in automotive sector are looking for the optimal solution to model and understand tire's behavior both in experimental and simulation environments. The studies carried out and the tool developed herein demonstrate a new approach in tire characterization and in vehicle simulation procedures. This enables the reproduction of the dynamic response of a tire through the use of specific track sessions, carried out with the aim to employ the vehicle as a moving lab. The final product, named TRICK tool (Tire/Road Interaction Characterization and Knowledge), comprises of a vehicle model which processes experimental signals acquired from vehicle CAN bus and from sideslip angle estimation additional instrumentation. The output of the tool is several extra "virtual telemetry" channels, based on the time history of the acquired signals and containing force and slip estimations, useful to provide tire interaction characteristics. TRICK results can be integrated with the physical models developed by the Vehicle Dynamics UniNa research group, providing a multitude of working solutions and constituting an ideal instrument for the prediction and the simulation of the real tire dynamics.

Technical and environmental assessment of the scrap tire vacuum pyrolysis process

International Nuclear Information System (INIS)

Roy, C.; Caumia, B. de; Lebrecque, B.; Blanchette, D.; Pakdel, H.; Roy, V.

1991-01-01

Tire recycling has become a necessity because of the huge piles of tires which represent a threat to the environment. There is about one worn tire produced per year and per person in the developed countries. The used tires represent a source of energy and valuable chemical products. By thermal decomposition of rubber under reduced pressure, it is possible to recover the useful compounds. A step by step approach has been used, from bench-scale batch systems, to process development and finally pilot plant, to experiment and develop vacuum pyrolysis of used tires. Yields are: 55% oil, 25% carbon black, 9% steel, 5% fiber and 6% gas. The maximum recovery of oil was performed at 415 degree C below 2 kPa abs. The specific gravity of this oil was 0.95, its gross heating value was 43 MJ/kg and total sulfur content about 0.8%. It was rich in limonene, benzol and other petrochemical components. The carbon black favorably compared with the low standard grades and may find an application in low grade rubber goods following further research and development. From an environmental point of view, the quality of the gas emissions was found to be acceptable based on the province of Quebec regulations. The aqueous phase contains toxic substances which will be eliminated after blending and burning it with pyrolysis oils used to heat up the reactor. The heat of pyrolysis for the reactions is low, estimated around 700 kJ/kg. The process has been tested in a 200 kg/h pilot plant, which positively demonstrated the possibility of continuously feeding large chunks of rubber under a vacuo. The process feasibility is promising, with returns on the investment of 31% after three years of operation. 9 refs., 4 figs., 8 tabs

Tire aging: a human factors analysis of failure to warn and inform.

Science.gov (United States)

Wogalter, Michael S; Laughery, Kenneth R

2012-01-01

A scenario of an automotive accident caused by tire failure is given followed by a human factors analysis of the information available to consumers on tire aging. Consumers have not been told that the age of the tire is a safety concern. It is not easy to decode the date of manufacture on tires. More publicity and prominent warnings are needed to communicate the dangers of older tires. Also, better ways to present the date of manufacture so that consumers can more easily and accurately assess tire age are needed.

Gear Tooth Wear Detection Algorithm

Science.gov (United States)

Delgado, Irebert R.

2015-01-01

Vibration-based condition indicators continue to be developed for Health Usage Monitoring of rotorcraft gearboxes. Testing performed at NASA Glenn Research Center have shown correlations between specific condition indicators and specific types of gear wear. To speed up the detection and analysis of gear teeth, an image detection program based on the Viola-Jones algorithm was trained to automatically detect spiral bevel gear wear pitting. The detector was tested using a training set of gear wear pictures and a blind set of gear wear pictures. The detector accuracy for the training set was 75 percent while the accuracy for the blind set was 15 percent. Further improvements on the accuracy of the detector are required but preliminary results have shown its ability to automatically detect gear tooth wear. The trained detector would be used to quickly evaluate a set of gear or pinion pictures for pits, spalls, or abrasive wear. The results could then be used to correlate with vibration or oil debris data. In general, the program could be retrained to detect features of interest from pictures of a component taken over a period of time.

78 FR 66655 - Consumer Information; Uniform Tire Quality Grading Standards

Science.gov (United States)

2013-11-06

... information indicating the relative performance of passenger car tires in the areas of treadwear, traction... [Docket No. NHTSA-2013-0120] RIN 2127-AL49 Consumer Information; Uniform Tire Quality Grading Standards...). ACTION: Interim final rule; request for comments. SUMMARY: The Uniform Tire Quality Grading Standards...

Forensic analysis of tire rubbers based on their sulfur chemical states.

Science.gov (United States)

Funatsuki, Atsushi; Shiota, Kenji; Takaoka, Masaki; Tamenori, Yusuke

2015-05-01

The chemical states of sulfur in 11 tires were analyzed using X-ray absorption near-edge structure (XANES) in order to discriminate between various tire rubbers. All tires had peaks around 2471.5 and 2480.5eV, and the shapes and heights of these peaks differed among tires, suggesting that the sulfur chemical state could be used for discrimination between tire rubbers. Based on t-tests on the results of XANES, 43 of 55 combinations were different at a significance level of 5%. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Deterministic and Stochastic Semi-Empirical Transient Tire Models

OpenAIRE

Umsrithong, Anake

2012-01-01

The tire is one of the most important components of the vehicle. It has many functions, such as supporting the load of the vehicle, transmitting the forces which drive, brake and guide the vehicle, and acting as the secondary suspension to absorb the effect of road irregularities before transmitting the forces to the vehicle suspension. A tire is a complex reinforced rubber composite air container. The structure of the tire is very complex. It consists of several layers of synthetic polymer, ...

Combustion of used tires for energy recovery. Yozumi taiya shokyaku ni suru netsuriyo

Energy Technology Data Exchange (ETDEWEB)

Ishizawa, N. (Toyo Tire and Rubber Co. Ltd., Osaka (Japan))

1993-03-15

The recycled automobile tires in 1991 amounts to 87%, and the tires are used most effectively for heat generation. The utilization of tires for heat in Japan and in other countries are outlined, and a detailed report is made on the use of used tires as fuel at coal cogeneration plants in tire manufacturing plants. The 'utilization percent for heat' is steadily increasing among the recycling applications of used tires. Energy recovery by dry distillation method and by direct combustion method is discussed. The states of used tire utilization in America, West Germany, and Britain are introduced. A concrete example of utilization for heat of used tires at a tire manufacturing plant is shown. Used tires are chopped into chips, mixed and burned in a coal boiler, the generated steam is used as the heat source for private power generation, and the power is used as the power source for the plant. 15 refs., 5 figs., 7 tabs.

Blast overpressure after tire explosion: a fatal case.

Science.gov (United States)

Pomara, Cristoforo; D'Errico, Stefano; Riezzo, Irene; Perilli, Gabriela; Volpe, Umberto; Fineschi, Vittorio

2013-12-01

Fatal blast injuries are generally reported in literature as a consequence of the detonation of explosives in war settings. The pattern of lesion depends on the position of the victim in relation to the explosion, on whether the blast tracks through air or water, and whether it happens in the open air or within an enclosed space and the distance from the explosion. Tire explosion-related injuries are rarely reported in literature. This study presents a fatal case of blast overpressure due to the accidental explosion of a truck tire occurring in a tire repair shop. A multidisciplinary approach to the fatality involving forensic pathologists and engineers revealed that the accidental explosion, which caused a series of primary and tertiary blast wave injuries, was due to tire deterioration.

Spray From a Rolling Tire: Mechanics of Droplet Formation

Science.gov (United States)

Plocher, Dennis; Browand, Fred

2010-11-01

The spray pattern immediately behind a single-groove tire rolling on a wet surface is produced in the laboratory using a specially designed tire spray simulator. The spray development is examined using high speed video. Water from the groove forms a liquid sheet as the tire-tread lifts away from the surface. The sheet is not of uniform thickness, but it remains attached to the tread. The thinner portions of the sheet become even thinner as the tire rotates, and eventually break to produce holes near the tire surface. The holes grow as the sheet margins surrounding the holes retract into the thicker portions of the sheet which become roughly cylindrical "ligaments" aligned at right angles to the direction of spray motion. The ligaments break into large droplets via a Rayleigh instability. The smallest droplets form when the margins of two holes collide. As Weber number, We = ρU^2w/2σ , based on tire groove half width, w/2, varies by a factor of 25, the sheet-ligament structure persists, but ligaments become less organized, and more small droplets appear in the pattern.

49 CFR 575.106 - Tire fuel efficiency consumer information program.

Science.gov (United States)

2010-10-01

... to provide information indicating the relative performance of replacement passenger car tires in the... achieve the level of performance represented by each rating. (A) Ratings. Each tire shall be rated with... 49 Transportation 7 2010-10-01 2010-10-01 false Tire fuel efficiency consumer information program...

Tire recycling technologies: What is the future?

NARCIS (Netherlands)

Saiwari, Sitisaiyidah; van Hoek, Johannes Wilhelmus; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.; Blume, Anke; Heideman, G.

2016-01-01

Recycling is a heavily discussed topic nowadays, and recycled tire material to be re-used for the same application is one of the spear points of current R&D activities. Regarding the immense amount of used tires, more than just one outlet for the recycled material is needed. Besides the commonly

Evaluation of bifenthrin applications in tires to prevent Aedes mosquito breeding.

Science.gov (United States)

Nguyen, Huy T; Whelan, Peter I; Shortus, Matthew S; Jacups, Susan P

2009-03-01

The efficacy of maximum label rates of bifenthrin applications to dry tires to prevent Aedes mosquito breeding was investigated by field colonization and bioassay trials in shaded and unshaded locations. Aedes notoscriptus and Culex quinquefasciatus larvae were the most abundant species present in the field colonization trial. Colonization and survival of Ae. notoscriptus larvae to the late instar occurred significantly earlier in treated tires in shaded compared with unshaded locations (P = 0.002). Bifenthrin applications in shaded tires only prevented early instar survival for approximately 2.6 wk. Aedes notoscriptus late instars did not appear in the treated unshaded tires. Culex quinquefasciatus colonized treated tires from the 2nd wk in both shaded and unshaded treatments. In the bioassay, water from bifenthrin-treated tires, through extrapolation, was found to kill approximately 100% of late instar Ae. notoscriptus for only approximately 2.0-2.2 wk in shaded and unshaded tires. Under conditions optimal for Aedes breeding, such as shaded locations, high ambient temperatures, high relative humidity, and high amounts of leaf/organic matter accumulations, bifenthrin may not be effective as a larval control measure in tires for greater than 2.0-2.6 wk.

Use of ionizing radiation in the recycling of unserviceable tires of automotive and its adequate environmental disposal

International Nuclear Information System (INIS)

Souza, Clecia de Moura

2013-01-01

The aim of this study was to use ionizing radiation in the recycling of scrap tires of automotive. Samples of rubber unserviceable tires were irradiated with radiation doses 200, 400 and 600kGy in an electron accelerator. Subsequently, they were characterized by thermogravimetry (TG), differential scanning calorimetry (DSC), tensile strength mechanical test, spectrophotometry Fourier transform infrared (FTIR) and scanning electron microscopy (SEM). By thermogravimetry was possible to observe the effects of radiation in the mass loss of material. In the DSC curves were observed exothermic decomposition peaks and associated values of enthalpy variation (ΔH). The mechanical properties of the elastomeric matrix with unserviceable tires powder were studied and its behavior to ionizing radiation was analyzed. FTIR spectra were obtained in the 4000 - 650cm-1 region. It was observed that there was no change in the peaks due irradiation. For SEM the micrographs were enlarged from 32 times up to 1000 times and observed in sizes from 1mm up to 20μm. It was observed at doses of 200 and 400kGy, roughness corresponding to breaks or ruptures possibly caused by radiation. In 600kGy radiation dose was observed cavities caused by radiation. It was observed that at all doses occurred degradation. For samples without powder and with 10, 30 and 50% of unserviceable tires powder it was obtained micrographs of 100μm and 200μm amplification. Also it was possible to observe the incorporation of unserviceable tires powder of automotive in the elastomeric matrix of non-irradiated and irradiated samples. (author)

Who benefited from the US tariffs on the Chinese tires?

OpenAIRE

Joonhyung, Lee

2011-01-01

The purpose of this paper is to evaluate the short-run effect of the tariffs on Chinese tires imposed by the US in September 2009. First, we investigated whether the tariffs were beneficial to the US domestic tire industry in terms of employment. Our empirical analysis found that there were no significant benefits to US employment in the tire industry. This result led us to the next question: Who benefited from the tariffs? We found that the tire imports to the US were significantly deviated ...

Oxidative desulfurization of tire pyrolysis oil

OpenAIRE

Ahmad Shahzad; Ahmad Muhammad Imran; Naeem Khawar; Humayun Muhammad; Sebt-E-Zaeem; Faheem Farrukh

2016-01-01

This paper presents a low cost method for the purification of oils obtained from the pyrolysis of used tires. Oxidative desulfurization is a promising route for purification of tire pyrolysis oils as hydro-desulfurization may not be affordable for small scale industries. Different additives and acids have been employed for the enhancement of properties of pyrolytic oils. The experimental conditions were kept identical throughout, i.e. atmospheric pressure a...

Tire deflation device

Science.gov (United States)

Barker, Stacey G [Idaho Falls, ID

2010-01-05

A tire deflation device includes (1) a component having a plurality of bores, (2) a plurality of spikes removably insertable into the plurality of bores and (3) a keeper within each among the plurality of bores, the keeper being configured to contact a sidewall surface of a spike among the plurality of spikes and to exert force upon the sidewall surface. In an embodiment, the tire deflation device includes (a) a component including a bore in a material, the bore including a receiving region, a sidewall surface and a base surface, (b) a channel extending from the sidewall surface into the material, (c) a keeper having a first section housed within the channel and a second section which extends past the sidewall surface into the receiving region, and (d) a spike removably insertable into the bore.

Laser cleaning of the contaminations on the surface of tire mould

Science.gov (United States)

Ye, Yayun; Jia, Baoshen; Chen, Jing; Jiang, Yilan; Tang, Hongping; Wang, Haijun; Luan, Xiaoyu; Liao, Wei; Zhang, Chuanchao; Yao, Caizhen

2017-07-01

During the manufacturing of tires, surface pollutants on tire mould will lead to the production of unqualified tires. Tire moulds need to be regularly cleaned. Laser cleaning is recognized as a non-destructive, effective, precise and environmental friendly method. In this paper, laser cleaning was used to remove contaminants on tire mould surface. First, laser induced damage experiments were performed. The results showed that the roughness and hardness of the cast steel sample surface seldom changed under the energy range of 140.1-580.2 mJ laser irradiation 1 pulse and the energy range of 44.7-168.9 mJ laser irradiation 100 pulses. In the laser cleaning experiments, the cleaning thresholds and the optimal cleaning parameters were obtained. Results indicated that laser cleaning was safe and effective for tire mould contamination removal.

49 CFR 579.26 - Reporting requirements for manufacturers of tires.

Science.gov (United States)

2010-10-01

... imported is less than 15,000, or are deep tread, winter-type snow tires, space-saver or temporary use spare... 49 Transportation 7 2010-10-01 2010-10-01 false Reporting requirements for manufacturers of tires... requirements for manufacturers of tires. For each reporting period, a manufacturer (including a brand name...

Application of granulating of tires; Aplicaciones de granulado de NFUs

Energy Technology Data Exchange (ETDEWEB)

Jimenez Justicia, A.

2001-07-01

At present, used tires are mainly used as fuel, retreading and granulating of tires. In this article. I will focus on the last option, talking about some of the multiple applications and going into detail of the making process of the granulation of used tires in a recycling plant. (Author)

Tire-Pavement Friction Characteristics with Elastic Properties of Asphalt Pavements

Directory of Open Access Journals (Sweden)

Miao Yu

2017-11-01

Full Text Available The skid-resisting performance of pavement is a critical factor in traffic safety. Recent studies primarily analyze this behavior by examining the macro or micro texture of the pavement. It is inevitable that skid-resistance declines with time because the texture of pavement deteriorates throughout its service life. The primary objective of this paper is to evaluate the use of different asphalt pavements, varying in resilience, to optimize braking performance on pavement. Based on the systematic dynamics of tire-pavement contact, and analysis of the tire-road coupled friction mechanism and the effect of enlarging the tire-pavement contact area, road skid resistance was investigated by altering the elastic modulus of asphalt pavement. First, this research constructed the kinetic contact model to simulate tire-pavement friction. Next, the following aspects of contact behaviors were studied when braking: tread deformation in the tangential pavement interface, actual tire-pavement contact in the course, and the frictional braking force transmitted from the pavement to the tires. It was observed that with improvements in pavement elasticity, the actual tire-pavement contact area increased, which gives us the ability to effectively strengthen the frictional adhesion of the tire to the pavement. It should not be overlooked that the improvement in skid resistance was caused by an increase in pavement elasticity. This research approach provides a theoretical basis and design reference for the anti-skid research of asphalt pavements.

A Multisensing Setup for the Intelligent Tire Monitoring.

Science.gov (United States)

Coppo, Francesco; Pepe, Gianluca; Roveri, Nicola; Carcaterra, Antonio

2017-03-12

The present paper offers the chance to experimentally measure, for the first time, the internal tire strain by optical fiber sensors during the tire rolling in real operating conditions. The phenomena that take place during the tire rolling are in fact far from being completely understood. Despite several models available in the technical literature, there is not a correspondently large set of experimental observations. The paper includes the detailed description of the new multi-sensing technology for an ongoing vehicle measurement, which the research group has developed in the context of the project OPTYRE. The experimental apparatus is mainly based on the use of optical fibers with embedded Fiber Bragg Gratings sensors for the acquisition of the circumferential tire strain. Other sensors are also installed on the tire, such as a phonic wheel, a uniaxial accelerometer, and a dynamic temperature sensor. The acquired information is used as input variables in dedicated algorithms that allow the identification of key parameters, such as the dynamic contact patch, instantaneous dissipation and instantaneous grip. The OPTYRE project brings a contribution into the field of experimental grip monitoring of wheeled vehicles, with implications both on passive and active safety characteristics of cars and motorbikes.

Properties of concrete containing scrap-tire rubber--an overview.

Science.gov (United States)

Siddique, Rafat; Naik, Tarun R

2004-01-01

Solid waste management is one of the major environmental concerns in the United States. Over 5 billion tons of non-hazardous solid waste materials are generated in USA each year. Of these, more than 270 million scrap-tires (approximately 3.6 million tons) are generated each year. In addition to this, about 300 million scrap-tires have been stockpiled. Several studies have been carried out to reuse scrap-tires in a variety of rubber and plastic products, incineration for production of electricity, or as fuel for cement kilns, as well as in asphalt concrete. Studies show that workable rubberized concrete mixtures can be made with scrap-tire rubber. This paper presents an overview of some of the research published regarding the use of scrap-tires in portland cement concrete. The benefits of using magnesium oxychloride cement as a binder for rubberized concrete mixtures are also presented. The paper details the likely uses of rubberized concrete.

26 x 6.6 radial-belted aircraft tire performance

Science.gov (United States)

Davis, Pamela A.; Martinson, Veloria J.; Yager, Thomas J.; Stubbs, Sandy M.

1991-01-01

Preliminary results from testing of 26 x 6.6 radial-belted and bias-ply aircraft tires at NASA Langley's Aircraft Landing Dynamics Facility (ALDF) are reviewed. The 26 x 6.6 tire size evaluation includes cornering performance tests throughout the aircraft ground operational speed range for both dry and wet runway surfaces. Static test results to define 26 x 6.6 tire vertical stiffness properties are also presented and discussed.

A semi-analytical solution to accelerate spin-up of a coupled carbon and nitrogen land model to steady state

Directory of Open Access Journals (Sweden)

J. Y. Xia

2012-10-01

Full Text Available The spin-up of land models to steady state of coupled carbon–nitrogen processes is computationally so costly that it becomes a bottleneck issue for global analysis. In this study, we introduced a semi-analytical solution (SAS for the spin-up issue. SAS is fundamentally based on the analytic solution to a set of equations that describe carbon transfers within ecosystems over time. SAS is implemented by three steps: (1 having an initial spin-up with prior pool-size values until net primary productivity (NPP reaches stabilization, (2 calculating quasi-steady-state pool sizes by letting fluxes of the equations equal zero, and (3 having a final spin-up to meet the criterion of steady state. Step 2 is enabled by averaged time-varying variables over one period of repeated driving forcings. SAS was applied to both site-level and global scale spin-up of the Australian Community Atmosphere Biosphere Land Exchange (CABLE model. For the carbon-cycle-only simulations, SAS saved 95.7% and 92.4% of computational time for site-level and global spin-up, respectively, in comparison with the traditional method (a long-term iterative simulation to achieve the steady states of variables. For the carbon–nitrogen coupled simulations, SAS reduced computational cost by 84.5% and 86.6% for site-level and global spin-up, respectively. The estimated steady-state pool sizes represent the ecosystem carbon storage capacity, which was 12.1 kg C m⁻² with the coupled carbon–nitrogen global model, 14.6% lower than that with the carbon-only model. The nitrogen down-regulation in modeled carbon storage is partly due to the 4.6% decrease in carbon influx (i.e., net primary productivity and partly due to the 10.5% reduction in residence times. This steady-state analysis accelerated by the SAS method can facilitate comparative studies of structural differences in determining the ecosystem carbon storage capacity among biogeochemical models. Overall, the

Evaluation of substitution monopole models for tire noise sound synthesis

Science.gov (United States)

Berckmans, D.; Kindt, P.; Sas, P.; Desmet, W.

2010-01-01

Due to the considerable efforts in engine noise reduction, tire noise has become one of the major sources of passenger car noise nowadays and the demand for accurate prediction models is high. A rolling tire is therefore experimentally characterized by means of the substitution monopole technique, suiting a general sound synthesis approach with a focus on perceived sound quality. The running tire is substituted by a monopole distribution covering the static tire. All monopoles have mutual phase relationships and a well-defined volume velocity distribution which is derived by means of the airborne source quantification technique; i.e. by combining static transfer function measurements with operating indicator pressure measurements close to the rolling tire. Models with varying numbers/locations of monopoles are discussed and the application of different regularization techniques is evaluated.

The build up of the correlation between halo spin and the large-scale structure

Science.gov (United States)

Wang, Peng; Kang, Xi

2018-01-01

Both simulations and observations have confirmed that the spin of haloes/galaxies is correlated with the large-scale structure (LSS) with a mass dependence such that the spin of low-mass haloes/galaxies tend to be parallel with the LSS, while that of massive haloes/galaxies tend to be perpendicular with the LSS. It is still unclear how this mass dependence is built up over time. We use N-body simulations to trace the evolution of the halo spin-LSS correlation and find that at early times the spin of all halo progenitors is parallel with the LSS. As time goes on, mass collapsing around massive halo is more isotropic, especially the recent mass accretion along the slowest collapsing direction is significant and it brings the halo spin to be perpendicular with the LSS. Adopting the fractional anisotropy (FA) parameter to describe the degree of anisotropy of the large-scale environment, we find that the spin-LSS correlation is a strong function of the environment such that a higher FA (more anisotropic environment) leads to an aligned signal, and a lower anisotropy leads to a misaligned signal. In general, our results show that the spin-LSS correlation is a combined consequence of mass flow and halo growth within the cosmic web. Our predicted environmental dependence between spin and large-scale structure can be further tested using galaxy surveys.

Development of an Intelligent Tire Based Tire - Vehicle State Estimator for Application to Global Chassis Control

OpenAIRE

Singh, Kanwar Bharat

2012-01-01

The contact between the tire and the road is the key enabler of vehicle acceleration, deceleration and steering. However, under the circumstances of sudden changes to the road conditions, the driver`s ability to maintain control of the vehicle maybe at risk. In many cases, this requires intervention from the chassis control systems onboard the vehicle. Although these systems perform well in a variety of situations, their performance can be improved if a real-time estimate of the tire-road c...

3rd symposium on tires and chassis; 3. Symposium Reifen und Fahrwerk

Energy Technology Data Exchange (ETDEWEB)

Geringer, B.; Stumpf, H. (comps.)

2005-07-01

The present volume contains the talks, which were held at the 3rd symposium on ''Tires and chassis'' at the Institute for combustion machines at the Technical University Vienna on 26th September 2005 in cooperation with UAMTTC and Semperit Reifen Ges.m.H. Apart from technical improvements on chassis, tires and carriageway the overall perspective will get more important in the future, which also includes the driver, the neighbour, the environment and the traffic policy. Due to an increasing number of international participants, discussions can be expected, which will take into consideration extraordinary and manifold perspectives. The third symposium on ''Tires and chassis'' discusses the following developments, of which some are evolutionary. (a) Tire engineering; environmental aspects of tires, roll resistance of tires, driving comfort of tires, winter tires for passenger vehicles and trucks. (b) vehicle engineering, engineering of a race car chassis by means of telemetric measuring data acquisition; simulation of steering wheel vibrations on a complete vehicle test stand. (c) Vehicle steering; chassis of tracklaying vehicles; automatic air pressure control. (orig.)

A Synthesis on the Evolution of the Studded Tire

National Research Council Canada - National Science Library

Angerinos, Michael

1998-01-01

Ever since studded tires were flrst introduced, the advantages, disadvantages, and effects of studded tires on vehicles, drivers and pavement systems has been the center of research and controversy...

Rubber - application of radiation to tire manufacture

International Nuclear Information System (INIS)

Hunt, J.D.; Alliger, G.

1979-01-01

Since the advent of commercial accelerators during the last several years capable of producing controllable electron beams of high energy, Firestone has devoted a considerable effort to the better understanding of the possible applications of such radiation to the production of tires or tire components. A number of chemical reactions can occur when elastomeric compounds are exposed to high energy waves, but crosslinking and degradation are the most important. The degree to which the crosslinking reaction predominates depends upon the nature of the rubber, compounding ingredients and the dosage. In general then, the effects achieved by the radiation of a rubber are quite similar to those resulting from heat. However, radiation cure or precure of compounds offers the advantage that the degree of crosslinking can be better controlled. Uniform crosslinking is possible since the high speed electrons penetrate uniformly throughout the sample. Curing with heat on the other hand may result in a greater degree of crosslinking on the surface of the sample than the center because of low heat conductivity. In general, radiation can be used to advantage to crosslink partially rubber tire components so that they retain better their shape and dimension during tire assembly and final cure or vulcanization. Added advantages of radiation precure include: a reduction of material usage, substitution of synthetic for natural rubber without loss in strength and the fact that partially crosslinked components will not thin out or become displaced during construction and vulcanization of the tire. (author)

Flexible and conductive waste tire-derived carbon/polymer composite paper as pseudocapacitive electrode

Science.gov (United States)

Naskar, Amit K.; Paranthaman, Mariappan Parans; Boota, Muhammad; Gogotsi, Yury

2018-04-10

A method of making a supercapacitor from waste tires, includes the steps of providing rubber pieces and contacting the rubber pieces with a sulfonation bath to produce sulfonated rubber; pyrolyzing the sulfonated rubber to produce a tire-derived carbon composite comprising carbon black embedded in rubber-derived carbon matrix comprising graphitized interface portions; activating the tire-derived carbon composite by contacting the tire-derived carbon composite with a specific surface area-increasing composition to increase the specific surface area of the carbon composite to provide an activated tire-derived carbon composite; and, mixing the activated tire-derived carbon composite with a monomer and polymerizing the monomer to produce a redox-active polymer coated, activated tire-derived carbon composite. The redox-active polymer coated, activated tire-derived carbon composite can be formed into a film. An electrode and a supercapacitor are also disclosed.

Feasibility of Energy Harvesting Using a Piezoelectric Tire

Science.gov (United States)

Malotte, Christopher

While the piezoelectric effect has been around for some time, it has only recently caught interest as a potential sustainable energy harvesting device. Piezoelectric energy harvesting has been developed for shoes and panels, but has yet to be integrated into a marketable bicycle tire. For this thesis, the development and feasibility of a piezoelectric tire was done. This includes the development of a circuit that incorporates piezoceramic elements, energy harvesting circuitry, and an energy storage device. A single phase circuit was designed using an ac-dc diode rectifier. An electrolytic capacitor was used as the energy storage device. A financial feasibility was also done to determine targets for manufacturing cost and sales price. These models take into account market trends for high performance tires, economies of scale, and the possibility of government subsidies. This research will help understand the potential for the marketability of a piezoelectric energy harvesting tire that can create electricity for remote use. This study found that there are many obstacles that must be addressed before a piezoelectric tire can be marketed to the general public. The power output of this device is minuscule compared to an alkaline battery. In order for this device to approach the power output of an alkaline battery the weight of the device would also become an issue. Additionally this device is very costly compared to the average bicycle tire. Lastly, this device is extreme fragile and easily broken. In order for this device to become marketable the issues of power output, cost, weight, and durability must all be successfully overcome.

The influence of the tire inflation on pull properties of agriculture tractors

Directory of Open Access Journals (Sweden)

Jakub Katrenčík

2013-01-01

Full Text Available Agricultural tractors are robust and versatile machines, which must comply with the basic requirements of users under various conditions. The main requirements include economical and reliable operation and high performance. Fuel economy could be improved using multiple methods, for example a well trained operator, adequate farming conditions and optimal tire inflation. Tractor tires transmit engine power to the surface and as such they are crucial to tractor operation. In the first part of the field measurement, all tires were inflated to 180kPa, while in the second part of the field measurements the tire pressure was set to 75kPa in front tires and to 65 kPa in rear tires. The results of the field measurement of the John Deere 6920S tractor with different tire inflation shows that pull performance increased by 9.9% and wheel slip decreased by 9.7%.

Vibration Analysis of a Tire in Ground Contact under Varied Conditions

OpenAIRE

Karakus Murat; Cavus Aydin; Colakoglu Mehmet

2017-01-01

The effect of three different factors, which are inflation pressure, vertical load and coefficient of friction on the natural frequencies of a tire (175/70 R13) has been studied. A three dimensional tire model is constructed, using four different material properties and parts in the tire. Mechanical properties of the composite parts are evaluated. After investigating the free vibration, contact analysis is carried out. A concrete block and the tire are modelled together, using three different...

Tire Shred Backfill in Mechanically Stabilized Earth Wall Applications

OpenAIRE

Balunaini, Umashankar; Yoon, Sungmin; Prezzi, Monica; Salgado, Rodrigo

2009-01-01

Tire shred-soil mixture backfill for use in mechanically stabilized earth (MSE) walls has several advantages over traditional backfill materials: 1) good drainage, 2) high shear strength, 3) low compacted unit weight and 4) low lateral pressure exerted on retaining structures. This work presents the results of laboratory tests performed on tire shred-sand mixtures focusing on determining the properties required for their use as backfill in MSE wall applications. Three sizes of tire shreds are...

Predicting the compressibility behaviour of tire shred samples for landfill applications.

Science.gov (United States)

Warith, M A; Rao, Sudhakar M

2006-01-01

Tire shreds have been used as an alternative to crushed stones (gravel) as drainage media in landfill leachate collection systems. The highly compressible nature of tire shreds (25-47% axial strain on vertical stress applications of 20-700 kPa) may reduce the thickness of the tire shred drainage layer to less than 300 mm (minimum design requirement) during the life of the municipal solid waste landfill. There hence exists a need to predict axial strains of tire shred samples in response to vertical stress applications so that the initial thickness of the tire shred drainage layer can be corrected for compression. The present study performs one-dimensional compressibility tests on four tire shred samples and compares the results with stress/strain curves from other studies. The stress/strain curves are developed into charts for choosing the correct initial thickness of tire shred layers that maintain the minimum thickness of 300 mm throughout the life of the landfill. The charts are developed for a range of vertical stresses based on the design height of municipal waste cell and bulk unit weight of municipal waste. Experimental results also showed that despite experiencing large axial strains, the average permeability of the tire shred sample consistently remained two to three orders of magnitude higher than the design performance criterion of 0.01cm/s for landfill drainage layers. Laboratory experiments, however, need to verify whether long-term chemical and bio-chemical reactions between landfill leachate and the tire shred layer will deteriorate their mechanical functions (hydraulic conductivity, compressibility, strength) beyond permissible limits for geotechnical applications.

A Multisensing Setup for the Intelligent Tire Monitoring

Directory of Open Access Journals (Sweden)

Francesco Coppo

2017-03-01

Full Text Available The present paper offers the chance to experimentally measure, for the first time, the internal tire strain by optical fiber sensors during the tire rolling in real operating conditions. The phenomena that take place during the tire rolling are in fact far from being completely understood. Despite several models available in the technical literature, there is not a correspondently large set of experimental observations. The paper includes the detailed description of the new multi-sensing technology for an ongoing vehicle measurement, which the research group has developed in the context of the project OPTYRE. The experimental apparatus is mainly based on the use of optical fibers with embedded Fiber Bragg Gratings sensors for the acquisition of the circumferential tire strain. Other sensors are also installed on the tire, such as a phonic wheel, a uniaxial accelerometer, and a dynamic temperature sensor. The acquired information is used as input variables in dedicated algorithms that allow the identification of key parameters, such as the dynamic contact patch, instantaneous dissipation and instantaneous grip. The OPTYRE project brings a contribution into the field of experimental grip monitoring of wheeled vehicles, with implications both on passive and active safety characteristics of cars and motorbikes.

Performance indicators, practices and maintenance costs in tires management of a transport company

Directory of Open Access Journals (Sweden)

Marcos Dario

2014-12-01

Full Text Available There are three operational costs that are more expressive for PSL: vehicle maintenance, tires and fuel. In studies of maintenance has been little researched the concept of tire management, technical maintenance and performance together. In this context, this study aims at identifying the practices and performance indicators in the area of maintenance and tire management also analyze the influence of costs applied to the tires on the total cost of maintenance. We conducted a case study of exploratory and descriptive. The main instruments of data collection were on-site observation, unstructured interviews, document analysis and reports results indicators. Data were analyzed by correlation analysis and multiple regression. It was revealed that among the performance indicators in the management of tire maintenance costs applied to the tires have a higher correlation with the total cost of maintenance. The ANOVA indicated that tire maintenance costs influence in 54% of the variations in the total cost of maintenance. We clarified the concepts of maintenance techniques specific tire management, and identify performance indicators in the area of tire managent.

Co-pyrolysis of waste tire/coal mixtures for smokeless fuel, maltenes and hydrogen-rich gas production

International Nuclear Information System (INIS)

Bičáková, Olga; Straka, Pavel

2016-01-01

Highlights: • Co-pyrolysis of waste tires/coal mixtures yields mainly smokeless fuel (55–74 wt%). • Alternatively, the smokeless fuel can serve as carbonaceous sorbent. • The obtained tar contained maltenes (80–85 wt%) and asphaltenes (6–8 wt%). • Tar from co-pyrolysis can serve as heating oil or a source of maltenes for repairing of asphalt surfaces. • The hydrogen-rich gas was obtained (61–65 vol% H_2, 24–25 vol% CH_4, 1.4–2 vol% CO_2). - Abstract: The processing of waste tires with two different types of bituminous coal was studied through the slow co-pyrolysis of 1 kg of waste tire/coal mixtures with 15, 30 and 60 wt% waste tires on a laboratory scale. The waste tire/coal mixtures were pyrolysed using a quartz reactor in a stationary bed. The mixtures were heated at a rate 5 °C/min up to the final temperature of 900 °C with a soaking time of 30 min at the required temperature. The mass balance of the process and the properties of the coke and tar obtained were evaluated, further, the influence of the admixture in the charge on the amount and composition of the obtained coke and tar was determined. It was found that the smokeless fuel/carbonaceous sorbent and a high yield of tar for further use can be obtained through the slow co-pyrolysis. The obtained tars contained mostly maltenes (80–85 wt%). FTIR analysis showed that the maltenes from the co-pyrolysis of coal/waste tires exhibited significantly lower aromaticity as compared with that from coal alone. The gas obtained from pyrolysis or co-pyrolysis of waste tire/coal mixtures contained a high amount of hydrogen (above 60 vol%) and methane (above 20 vol%).

Silica-filled tire tread compounds: an investigation into the viscoelastic properties of the rubber compounds and their relation to tire performance

NARCIS (Netherlands)

Maghami, S.

2016-01-01

With increasing the global concern for fossil fuel consumption, automotive industry moves toward more efficient vehicles. Tires are of great importance in this respect, as the tire compound material in contact with the road surface and under the cyclic deformation dissipates energy due to its

Fatigue of cord-rubber composites for tires

Science.gov (United States)

Song, Jaehoon

Fatigue behaviors of cord-rubber composite materials forming the belt region of radial pneumatic tires have been characterized to assess their dependence on stress, strain and temperature history as well as materials composition and construction . Using actual tires, it was found that interply shear strain is one of the crucial parameters for damage assessment from the result that higher levels of interply shear strain of actual tires reduce the fatigue lifetime. Estimated at various levels of load amplitude were the fatigue life, the extent and rate of resultant strain increase ("dynamic creep"), cyclic strains at failure, and specimen temperature. The interply shear strain of 2-ply 'tire belt' composite laminate under circumferential tension was affected by twisting of specimen due to tension-bending coupling. However, a critical level of interply shear strain, which governs the gross failure of composite laminate due to the delamination, appeared to be independent of different lay-up of 2-ply vs. symmetric 4-ply configuration. Reflecting their matrix-dominated failure modes such as cord-matrix debonding and delamination, composite laminates with different cord reinforcements showed the same S-N relationship as long as they were constructed with the same rubber matrix, the same cord angle, similar cord volume, and the same ply lay-up. Because of much lower values of single cycle strength (in terms of gross fracture load per unit width), the composite laminates with larger cord angle and the 2-ply laminates exhibited exponentially shorter fatigue lifetime, at a given stress amplitude, than the composite laminates with smaller cord angle and 4-ply symmetric laminates, respectively. The increase of interply rubber thickness lengthens their fatigue lifetime at an intermediate level of stress amplitude. However, the increase in the fatigue lifetime of the composite laminate becomes less noticeable at very low stress amplitude. Even with small compressive cyclic

Influence of different processing techniques on the mechanical properties of used tires in embankment construction

International Nuclear Information System (INIS)

Edincliler, Ayse; Baykal, Goekhan; Saygili, Altug

2010-01-01

Use of the processed used tires in embankment construction is becoming an accepted way of beneficially recycling scrap tires due to shortages of natural mineral resources and increasing waste disposal costs. Using these used tires in construction requires an awareness of the properties and the limitations associated with their use. The main objective of this paper is to assess the different processing techniques on the mechanical properties of used tires-sand mixtures to improve the engineering properties of the available soil. In the first part, a literature study on the mechanical properties of the processed used tires such as tire shreds, tire chips, tire buffings and their mixtures with sand are summarized. In the second part, large-scale direct shear tests are performed to evaluate shear strength of tire crumb-sand mixtures where information is not readily available in the literature. The test results with tire crumb were compared with the other processed used tire-sand mixtures. Sand-used tire mixtures have higher shear strength than that of the sand alone and the shear strength parameters depend on the processing conditions of used tires. Three factors are found to significantly affect the mechanical properties: normal stress, processing techniques, and the used tire content.

Influence of different processing techniques on the mechanical properties of used tires in embankment construction.

Science.gov (United States)

Edinçliler, Ayşe; Baykal, Gökhan; Saygili, Altug

2010-06-01

Use of the processed used tires in embankment construction is becoming an accepted way of beneficially recycling scrap tires due to shortages of natural mineral resources and increasing waste disposal costs. Using these used tires in construction requires an awareness of the properties and the limitations associated with their use. The main objective of this paper is to assess the different processing techniques on the mechanical properties of used tires-sand mixtures to improve the engineering properties of the available soil. In the first part, a literature study on the mechanical properties of the processed used tires such as tire shreds, tire chips, tire buffings and their mixtures with sand are summarized. In the second part, large-scale direct shear tests are performed to evaluate shear strength of tire crumb-sand mixtures where information is not readily available in the literature. The test results with tire crumb were compared with the other processed used tire-sand mixtures. Sand-used tire mixtures have higher shear strength than that of the sand alone and the shear strength parameters depend on the processing conditions of used tires. Three factors are found to significantly affect the mechanical properties: normal stress, processing techniques, and the used tire content. Copyright 2009. Published by Elsevier Ltd.

Upgrading pyrolytic residue from waste tires to commercial carbon black.

Science.gov (United States)

Zhang, Xue; Li, Hengxiang; Cao, Qing; Jin, Li'e; Wang, Fumeng

2018-05-01

The managing and recycling of waste tires has become a worldwide environmental challenge. Among the different disposal methods for waste tires, pyrolysis is regarded as a promising route. How to effectively enhance the added value of pyrolytic residue (PR) from waste tires is a matter of great concern. In this study, the PRs were treated with hydrochloric and hydrofluoric acids in turn under ultrasonic waves. The removal efficiency for the ash and sulfur was investigated. The pyrolytic carbon black (PCB) obtained after treating PR with acids was analyzed by X-ray fluorescence spectrophotometry, Fourier transform infrared spectrometry, X-ray diffractometry, laser Raman spectrometry, scanning electron microscopy, thermogravimetric (TG) analysis, and physisorption apparatus. The properties of PCB were compared with those of commercial carbon black (CCB) N326 and N339. Results showed PRs from waste tires were mainly composed of carbon, sulfur, and ash. The carbon in PCB was mainly from the CCB added during tire manufacture rather than from the pyrolysis of pure rubbers. The removal percentages for the ash and sulfur of PR are 98.33% (from 13.98 wt % down to 0.24 wt %) and 70.16% (from 1.81 wt % down to 0.54 wt %), respectively, in the entire process. The ash was mainly composed of metal oxides, sulfides, and silica. The surface properties, porosity, and morphology of the PCB were all close to those of N326. Therefore, PCB will be a potential alternative of N326 and reused in tire manufacture. This route successfully upgrades PR from waste tires to the high value-added CCB and greatly increases the overall efficiency of the waste tire pyrolysis industry.

Adsorbed natural gas storage with activated carbons made from Illinois coals and scrap tires

Science.gov (United States)

Sun, Jielun; Brady, T.A.; Rood, M.J.; Lehmann, C.M.; Rostam-Abadi, M.; Lizzio, A.A.

1997-01-01

Activated carbons for natural gas storage were produced from Illinois bituminous coals (IBC-102 and IBC-106) and scrap tires by physical activation with steam or CO2 and by chemical activation with KOH, H3PO4, or ZnCl2. The products were characterized for N2-BET area, micropore volume, bulk density, pore size distribution, and volumetric methane storage capacity (Vm/Vs). Vm/Vs values for Illinois coal-derived carbons ranged from 54 to 83 cm3/cm3, which are 35-55% of a target value of 150 cm3/cm3. Both granular and pelletized carbons made with preoxidized Illinois coal gave higher micropore volumes and larger Vm/Vs values than those made without preoxidation. This confirmed that preoxidation is a desirable step in the production of carbons from caking materials. Pelletization of preoxidized IBC-106 coal, followed by steam activation, resulted in the highest Vm/Vs value. With roughly the same micropore volume, pelletization alone increased Vm/Vs of coal carbon by 10%. Tire-derived carbons had Vm/Vs values ranging from 44 to 53 cm3/cm3, lower than those of coal carbons due to their lower bulk densities. Pelletization of the tire carbons increased bulk density up to 160%. However, this increase was offset by a decrease in micropore volume of the pelletized materials, presumably due to the pellet binder. As a result, Vm/Vs values were about the same for granular and pelletized tire carbons. Compared with coal carbons, tire carbons had a higher percentage of mesopores and macropores.

The design and improvement of radial tire molding machine

Science.gov (United States)

Wang, Wenhao; Zhang, Tao

2018-04-01

This paper presented that the high accuracy semisteel meridian tire molding machine structure configurations, combining tyre high precision characteristics, the original structure and parameter optimization, technology improvement innovation design period of opening and closing machine rotary shaping drum institutions. This way out of the shaft from the structure to the push-pull type movable shaping drum of thinking limit, compared with the specifications and shaping drum can smaller contraction, is conducive to forming the tire and reduce the tire deformation.

Performance of Used Tire Cushion Layer under Rockfall Impact

OpenAIRE

Sun, Jianhu; Chu, Zhaojun; Liu, Yingfang; Luo, Weiming; Wang, Min

2016-01-01

Rock shed is widely used in traffic lines against rockfall. In order to cushion rockfall impact and dissipate impact energy, cushion layer is usually adopted in rock shed. Used tire cushion layer is proposed in this paper and it can cushion rockfall impact utilizing large radial deformation of tire. Reinforced concrete structure model is built with used tire cushion layer and artificial rockfall test is carried out. Twelve tests are divided into 4 sets with different rockfall mass, rockfall h...

SIMULATION AND INVESTIGATION OF TIRE TREAD BLOCKS INTERACTION WITH ICE

Directory of Open Access Journals (Sweden)

Andrius Ružinskas

2017-12-01

Full Text Available The car tire is an essential subject analysing its interaction with the road. From tire’s tread condition, geometry and rubber compound depends grip and vehicle stability. This is especially relevant in winter time, when roads are covered with the layer of snow or ice. Generally, new tires are tested in real traffic conditions using vehicles. However, ensuring these conditions requires many resources and sometimes it could be a big challenge. For this reason, simulation of the tire interaction with the road becomes more important in nowadays tire researches. Since the tire is a complex engineering subject, the tire tread blocks could be separated for individual analysis. The interaction between the dry ice and the tread block with sipes was analysed using finite element analysis. The tread block was described using hyperelastic Mooney­Rivlin material model. The deformations, distribution of the contact pressure and shear stresses were obtained for the soft and hard rubber compounds with different vertical load conditions. Also a solid tread block interaction was analysed and it was found that values of contact pressure and shear stresses are much lower comparing to siped tread block.

Effects of Load and Speed on Wear Rate of Abrasive Wear for 2014 Al Alloy

Science.gov (United States)

Odabas, D.

2018-01-01

In this paper, the effects of the normal load and sliding speed on wear rate of two-body abrasive wear for 2014 Al Alloy were investigated in detail. In order to understand the variation in wear behaviour with load and speed, wear tests were carried out at a sliding distance of 11 m, a speed of 0.36 m/s, a duration of 30 s and loads in the range 3-11 N using 220 grit abrasive paper, and at a speed range 0.09-0.90 m/s, a load of 5 N and an average sliding distance of 11 m using abrasive papers of 150 grit size under dry friction conditions. Before the wear tests, solution treatment of the 2014 Al alloy was carried out at temperatures of 505 and 520 °C for 1 h in a muffle furnace and then quenched in cold water at 15 °C. Later, the ageing treatment was carried out at 185 °C for 8 h in the furnace. Generally, wear rate due to time increased linearly and linear wear resistance decreased with increasing loads. However, the wear rate was directly proportional to the load up to a critical load of 7 N. After this load, the slope of the curves decreased because the excessive deformation of the worn surface and the instability of the abrasive grains began to increase. When the load on an abrasive grain reaches a critical value, the groove width is about 0.17 of the abrasive grain diameter, and the abrasive grains begin to fail. The wear rate due to time increased slightly as the sliding speed increased in the range 0.09-0.90 m/s. The reason for this is that changes arising from strain rate and friction heating are expected with increasing sliding speeds.

Geotechnical Investigation of the Potential Use of Shredded Scrap Tires in Soil Stabilization.

Science.gov (United States)

1998-11-01

Silt-tire and clay-tire mixtures, containing 0% to 100% shredded tire material by weight, with tire chips ranging in size from 7mm-13mm, 13mm-25mm, and 25mm-38mm, were tested for a series of engineering properties including compaction characteristics...

14 CFR 29.475 - Tires and shock absorbers.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Tires and shock absorbers. 29.475 Section 29.475 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Strength Requirements Ground Loads § 29.475 Tires and shock absorbers. Unless otherwise...

Effectiveness of spinosad and temephos for the control of mosquito larvae at a tire dump in Allende, Nuevo Leon, Mexico.

Science.gov (United States)

Garza-Robledo, Argentina A; Martínez-Perales, Juan F; Rodríguez-Castro, Violeta A; Quiroz-Martínez, Humberto

2011-12-01

The effectiveness of spinosad and temephos for the control of mosquito larvae was evaluated in a tire dump in Allende, Nuevo Leon, Mexico. Three groups of 12 to 17 tires located in tree shade were utilized for this study. After the larvicides were applied, samples were collected weekly from 7 randomly chosen tires. The data showed a significant difference between the larvicides and control. Under the conditions of the present study, the effectiveness of spinosad against mosquito larvae was similar to that of temephos, both being effective for up to 91 days postapplication. In addition, spinosad allowed the establishment of the mosquito predator Toxorhynchites sp.

Oxidative desulfurization of tire pyrolysis oil

Directory of Open Access Journals (Sweden)

Ahmad Shahzad

2016-01-01

Full Text Available This paper presents a low cost method for the purification of oils obtained from the pyrolysis of used tires. Oxidative desulfurization is a promising route for purification of tire pyrolysis oils as hydro-desulfurization may not be affordable for small scale industries. Different additives and acids have been employed for the enhancement of properties of pyrolytic oils. The experimental conditions were kept identical throughout, i.e. atmospheric pressure and 50°C temperature for comparison of performance of various additives. The use of hydrogen peroxide-acetic acid mixture (10 wt.% was found more economical and effective in desulfurization and improvement of fuel properties of sample oils. The contribution of sulfuric acid in desulfurization and decreasing viscosity was also satisfactory but due to high price of concentrated sulfuric acid its use may not be economical. Calcium oxide and Fuller’s earth was not found to be effective in desulfurization. Results indicate that oxidative desulfurization could render tire pyrolysis oils suitable for blending as heating fuel.

Technical Note: Reducing the spin-up time of integrated surface water–groundwater models

KAUST Repository

Ajami, H.; Evans, J. P.; McCabe, Matthew; Stisen, S.

2014-01-01

uncertainty in model initialization is to run the model recursively using a single or multiple years of forcing data until the system equilibrates with respect to state and diagnostic variables. However, such "spin-up" approaches often require many years

A study on the fatigue life prediction of tire belt-layers using probabilistic method

International Nuclear Information System (INIS)

Lee, Dong Woo; Park, Jong Sang; Lee, Tae Won; Kim, Seong Rae; Sung, Ki Deug; Huh, Sun Chul

2013-01-01

Tire belt separation failure is occurred by internal cracks generated in *1 and *2 belt layers and by its growth. And belt failure seriously affects tire endurance. Therefore, to improve the tire endurance, it is necessary to analyze tire crack growth behavior and predict fatigue life. Generally, the prediction of tire endurance is performed by the experimental method using tire test machine. But it takes much cost and time to perform experiment. In this paper, to predict tire fatigue life, we applied deterministic fracture mechanics approach, based on finite element analysis. Also, probabilistic analysis method based on statistics using Monte Carlo simulation is presented. Above mentioned two methods include a global-local finite element analysis to provide the detail necessary to model explicitly an internal crack and calculate the J-integral for tire life prediction.

14 CFR 27.475 - Tires and shock absorbers.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Tires and shock absorbers. 27.475 Section 27.475 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Strength Requirements Ground Loads § 27.475 Tires and shock absorbers. Unless otherwise prescribed...

The experimental assessment of dynamic tire handling performance

NARCIS (Netherlands)

Pauwelussen, J.P.

1999-01-01

Testing of steady state tire handling performance is nowadays common practice with slip angle sweeps and breaking being simulated in the laboratory with drum or flat belt, or on the road with a test trailer. In recent years, more emphasis is put on dynamic tire models, motivated by ride comfort

Measurement of whole tire profile

Science.gov (United States)

Yang, Yongyue; Jiao, Wenguang

2010-08-01

In this paper, a precision measuring device is developed for obtaining characteristic curve of tire profile and its geometric parameters. It consists of a laser displacement measurement unit, a closed-loop precision two-dimensional coordinate table, a step motor control system and a fast data acquisition and analysis system. Based on the laser trigonometry, a data map of tire profile and coordinate values of all points can be obtained through corresponding data transformation. This device has a compact structure, a convenient control, a simple hardware circuit design and a high measurement precision. Experimental results indicate that measurement precision can meet the customer accuracy requirement of +/-0.02 mm.

Preventing Tire Blowout Accidents: A Perspective on Factors Affecting Drivers’ Intention to Adopt Tire Pressure Monitoring System

Directory of Open Access Journals (Sweden)

Kai-Ying Chen

2018-04-01

Full Text Available The aim of this study is to explore whether risk perception or anticipated regret is responsible for intensifying the participants’ intention to adopt a tire pressure monitoring system (TPMS to prevent a tire-related accident, and whether the optimism bias has a moderator effect between risk perception/anticipated regret and intention. With 274 valid questionnaires and PLS-SEM (partial least squares structural equation modeling analysis, the results indicate a significant positive relationship between risk perception and intention to adopt TPMS, but not between anticipated regret and intention. The moderator effect of optimism bias on risk perception and anticipated regret is not found in the model. The findings will prove useful for public service advertising campaigns by providing a basis for an understanding of the role of cognitive and emotional factors in tire-blowout accident prevention, thereby increasing the motivation for drivers in Taiwan to take advantage of the protection afforded them by using TPMS.

Technical Note: Reducing the spin-up time of integrated surface water–groundwater models

KAUST Repository

Ajami, H.; Evans, J. P.; McCabe, Matthew; Stisen, S.

2014-01-01

in model initialization is to run the model recursively using either a single year or multiple years of forcing data until the system equilibrates with respect to state and diagnostic variables. However, such "spin-up" approaches often require many years

Automobile tires--a potential source of highly carcinogenic dibenzopyrenes to the environment.

Science.gov (United States)

Sadiktsis, Ioannis; Bergvall, Christoffer; Johansson, Christer; Westerholm, Roger

2012-03-20

Eight tires were analyzed for 15 high molecular weight (HMW) polycyclic aromatic hydrocarbons (PAH), using pressurized fluid extraction. The variability of the PAH concentrations determined between different tires was large; a factor of 22.6 between the lowest and the highest. The relative abundance of the analytes was quite similar regardless of tire. Almost all (92.3%) of the total extractable PAH content was attributed to five PAHs: benzo[ghi]perylene, coronene, indeno[1,2,3-cd]pyrene, benzo[e]pyrene, and benzo[a]pyrene. The difference in the measured PAH content between summer and winter tires varied substantially across manufacturers, making estimates of total vehicle fleet emissions very uncertain. However, when comparing different types of tires from the same manufacturer they had significantly (p = 0.05) different PAH content. Previously, there have been no data available for carcinogenic dibenzopyrene isomers in automobile tires. In this study, the four dibenzopyrene isomers dibenzo[a,l]pyrene, dibenzo[a,e]pyrene, dibenzo[a,i]pyrene, and dibenzo[a,h]pyrene constituted tires may be a potential previously unknown source of carcinogenic dibenzopyrenes to the environment.

Biologically Based Restorative Management of Tooth Wear

Directory of Open Access Journals (Sweden)

Martin G. D. Kelleher

2012-01-01

Full Text Available The prevalence and severity of tooth wear is increasing in industrialised nations. Yet, there is no high-level evidence to support or refute any therapeutic intervention. In the absence of such evidence, many currently prevailing management strategies for tooth wear may be failing in their duty of care to first and foremost improve the oral health of patients with this disease. This paper promotes biologically sound approaches to the management of tooth wear on the basis of current best evidence of the aetiology and clinical features of this disease. The relative risks and benefits of the varying approaches to managing tooth wear are discussed with reference to long-term follow-up studies. Using reference to ethical standards such as “The Daughter Test”, this paper presents case reports of patients with moderate-to-severe levels of tooth wear managed in line with these biologically sound principles.

78 FR 21547 - Approval and Promulgation of Air Quality Implementation Plans; Oregon: Eugene-Springfield PM10

Science.gov (United States)

2013-04-11

... winter day emissions from point sources, residential wood combustion, road dust, and motor vehicle exhaust, brake and tire wear. The emissions inventory includes an inventory of point sources of PM 10... State's submittal. Emissions estimates for road dust and motor vehicle exhaust, brake wear, and tire...

Recycled tires as coarse aggregate in concrete pavement mixtures.

Science.gov (United States)

2013-07-01

The reuse potential of tire chips as coarse aggregates in pavement concrete was examined in this research by : investigating the effects of low- and high-volume tire chips on fresh and hardened concrete properties. One concrete : control mixture was ...

Neutron vibrational spectroscopic studies of novel tire-derived carbon materials.

Science.gov (United States)

Li, Yunchao; Cheng, Yongqiang; Daemen, Luke L; Veith, Gabriel M; Levine, Alan M; Lee, Richard J; Mahurin, Shannon M; Dai, Sheng; Naskar, Amit K; Paranthaman, Mariappan Parans

2017-08-23

Sulfonated tire-derived carbons have been demonstrated to be high value-added carbon products of tire recycling in several energy storage system applications including lithium, sodium, potassium ion batteries and supercapacitors. In this communication, we compared different temperature pyrolyzed sulfonated tire-derived carbons with commercial graphite and unmodified/non-functionalized tire-derived carbon by studying the surface chemistry and properties, vibrational spectroscopy of the molecular structure, chemical bonding such as C-H bonding, and intermolecular interactions of the carbon materials. The nitrogen adsorption-desorption studies revealed the tailored micro and meso pore size distribution of the carbon during the sulfonation process. XPS and neutron vibrational spectra showed that the sulfonation of the initial raw tire powders could remove the aliphatic hydrogen containing groups ([double bond splayed left]CH 2 and -CH 3 groups) and reduce the number of heteroatoms that connect to carbon. The absence of these functional groups could effectively improve the first cycle efficiency of the material in rechargeable batteries. Meanwhile, the introduced -SO 3 H functional group helped in producing terminal H at the edge of the sp 2 bonded graphite-like layers. This study reveals the influence of the sulfonation process on the recovered hard carbon from used tires and provides a pathway to develop and improve advanced energy storage materials.

Preliminary studies of the rubber from unserviceable tires irradiated by electron beam

International Nuclear Information System (INIS)

Souza, Clecia M.; Silva, Leonardo G. Andrade e

2011-01-01

Nowadays there is a growth in the developing processes for modification of polymers with ionizing radiation (gamma rays, electron beam) for several industrial applications. An option is ionizing radiation process due to their capacity of inducing crosslinking and scission on a wide range of polymeric materials without initiators or chemicals products. This method has significant advantages on economical and ecological fields, when compared to chemical, thermal and mechanical process. The rubber recycling has been extensively discussed, mainly related to tire. There are reports with data about production and consumption of rubber and unserviceable tire. There is very few information about the destination of others rubber items, incineration and landfill are the main methods for elimination of unserviceable tire, however those methods are not environmentally friendly. It is necessary to study better and effective methods to recycle and to give value to rubber residue. This work is about the use of ionizing radiation for the recovery and/or reuse and processing rubber of unserviceable tire. The samples were irradiated with 200, 400 and 600 kGy radiation dose, 22.39 kGy/s dose rates, at room temperature and in the presence of air using an 1.5 MeV electron beam accelerator. The irradiated and non-irradiated samples were studied by thermogravimetry (TG). The analyses were performed from room temperature up to 600 deg C, heating rate of 10 deg C/min in the presence of nitrogen (N 2 ) and air. By this technique it was possible to observe the effects of the radiation dose on the weight loss. (author)

Preliminary studies of the rubber from unserviceable tires irradiated by electron beam

Energy Technology Data Exchange (ETDEWEB)

Souza, Clecia M.; Silva, Leonardo G. Andrade e, E-mail: blgasilva@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

Nowadays there is a growth in the developing processes for modification of polymers with ionizing radiation (gamma rays, electron beam) for several industrial applications. An option is ionizing radiation process due to their capacity of inducing crosslinking and scission on a wide range of polymeric materials without initiators or chemicals products. This method has significant advantages on economical and ecological fields, when compared to chemical, thermal and mechanical process. The rubber recycling has been extensively discussed, mainly related to tire. There are reports with data about production and consumption of rubber and unserviceable tire. There is very few information about the destination of others rubber items, incineration and landfill are the main methods for elimination of unserviceable tire, however those methods are not environmentally friendly. It is necessary to study better and effective methods to recycle and to give value to rubber residue. This work is about the use of ionizing radiation for the recovery and/or reuse and processing rubber of unserviceable tire. The samples were irradiated with 200, 400 and 600 kGy radiation dose, 22.39 kGy/s dose rates, at room temperature and in the presence of air using an 1.5 MeV electron beam accelerator. The irradiated and non-irradiated samples were studied by thermogravimetry (TG). The analyses were performed from room temperature up to 600 deg C, heating rate of 10 deg C/min in the presence of nitrogen (N{sub 2}) and air. By this technique it was possible to observe the effects of the radiation dose on the weight loss. (author)

77 FR 11189 - Yokohama Tire Corporation, Denial of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2012-02-24

...-0056; Notice 2] Yokohama Tire Corporation, Denial of Petition for Decision of Inconsequential... Inconsequential Noncompliance. SUMMARY: Yokohama Tire Corporation, (YTC),\\1\\ replacement tires for passenger cars... Federal Motor Vehicle Safety Standard (FMVSS) No. 139, New Pneumatic Radial Tires for Light Vehicles. YTC...

Experimental and numerical study of friction and braking characteristics of rolling tires

NARCIS (Netherlands)

Steen, R. van der; Lopez, I.; Nijmeijer, H.; Schmeitz, A.J.C.; Bruijn, B. de

2011-01-01

Throughout the tire industry, virtual testing has been widely adopted in the design process. Both static deformation and dynamic response of the tire rolling on the road must be accurately predicted to evaluate the handling performance of a tire. Unfortunately, experimental characterization of

Contact of dual mobility implants: effects of cup wear and inclination.

Science.gov (United States)

Uddin, M S

2015-01-01

Cup wear and inclination on the pelvic bone are significant factors, which change the contact of the articulating surfaces, thus, impacting the long-term performance of hip implants. This paper presents a finite element (FE) analysis of the contact of the dual mobility implants under the influence of cup wear and inclination. A 3D FE model of the implant was developed with the application of equivalent physiological loading and boundary conditions. Effects of cup inclination angle ranging from 45° to 60° and the wear depth ranging from 0 to 2.46 mm equivalent to up to 30 years of the implant's life on the contact pressure and von Mises stress were investigated. Simulation results show that the contact pressure and von Mises stress decrease significantly with a modest wear depth and remains quite in-sensitive to the cup inclination angle and wear depth up to 1.64 mm. With wear depth further up to 2.46 mm, the cup thickness (i.e. cup thinning on worn region) may be more predominant than increasing of contact area between the cup and the head. The wear on the inner surface of the cup is found to rule out the overall contact pressure and stress in the implant. Furthermore, individual and combined effects of both important parameters are analysed and discussed with respect to available clinical/laboratory studies.

Federal Research Action Plan on Recycled Tire Crumb Used ...

Science.gov (United States)

Over the past several years, parents, athletes, schools, and communities have raised concerns about the safety of recycled tire crumb rubber used as infill for playing fields and playgrounds in the United States. The public has expressed concerns that the use of these fields could potentially be related to certain health effects. Studies to date have not shown an elevated health risk from playing on fields with tire crumb rubber, but these studies have limitations and do not comprehensively evaluate the concerns about health risks from exposure to tire crumb rubber. This status report provides a summary of activities to date, including: (1) stakeholder outreach, (2) the tire crumb rubber manufacturing industry, (3) the final peer-reviewed Literature Review/Gaps Analysis (LRGA), (4) progress on the research activities, and (5) next steps and a timeline for completion of the final report. The status report does not include research findings.

Construction of a test embankment using a sand-tire shred mixture as fill material.

Science.gov (United States)

Yoon, Sungmin; Prezzi, Monica; Siddiki, Nayyar Zia; Kim, Bumjoo

2006-01-01

Use of tire shreds in construction projects, such as highway embankments, is becoming an accepted way of beneficially recycling scrap tires. However, in the last decade there was a decline in the use of pure tire shreds as fill materials in embankment construction, as they are susceptible to fire hazards due to the development of exothermic reactions. Tire shred-sand mixtures, on the other hand, were found to be effective in inhibiting exothermic reactions. When compared with pure tire shreds, tire shred-sand mixtures are less compressible and have higher shear strength. However, the literature contains limited information on the use of tire shred-soil mixtures as a fill material. The objectives of this paper are to discuss and evaluate the feasibility of using tire shred-sand mixtures as a fill material in embankment construction. A test embankment constructed using a 50/50 mixture, by volume, of tire shreds and sand was instrumented and monitored to: (a) determine total and differential settlements; (b) evaluate the environmental impact of the embankment construction on the groundwater quality due to leaching of fill material; and (c) study the temperature variation inside the embankment. The findings in this research indicate that mixtures of tire shreds and sand are viable materials for embankment construction.

Transient tire force and its modeling. Part 2. Camber angle input; Katoteki tire hasseiryoku to sono modeling. 2. Camber kaku nyuryoku

Energy Technology Data Exchange (ETDEWEB)

Higuchi, A [Toyota Motor Corp., Aichi (Japan); Pacejka, H

1997-10-01

The objective of this study is to understand the transient force and moment characteristics of tires involving side slip and camber and to develop the tire model which is capable of describing those characteristics. Some particular characteristics are found such as non-lagging part in side force response and an apparent peak in aligning torque response to a stepwise camber change. Some aspects on the analogy of turn slip to camber are also discussed. The tire model combines a dynamic part based on the physical aspect using the relaxation length concept, and a steady state part. In combined situations of side slip and camber, an estimation method to determine the transient slip quantities is introduced. 12 refs., 14 figs.

Assessing the impact of model spin-up on surface water-groundwater interactions using an integrated hydrologic model

KAUST Repository

Ajami, Hoori

2014-03-01

Integrated land surface-groundwater models are valuable tools in simulating the terrestrial hydrologic cycle as a continuous system and exploring the extent of land surface-subsurface interactions from catchment to regional scales. However, the fidelity of model simulations is impacted not only by the vegetation and subsurface parameterizations, but also by the antecedent condition of model state variables, such as the initial soil moisture, depth to groundwater, and ground temperature. In land surface modeling, a given model is often run repeatedly over a single year of forcing data until it reaches an equilibrium state: the point at which there is minimal artificial drift in the model state or prognostic variables (most often the soil moisture). For more complex coupled and integrated systems, where there is an increased computational cost of simulation and the number of variables sensitive to initialization is greater than in traditional uncoupled land surface modeling schemes, the challenge is to minimize the impact of initialization while using the smallest spin-up time possible. In this study, multicriteria analysis was performed to assess the spin-up behavior of the ParFlow.CLM integrated groundwater-surface water-land surface model over a 208 km2 subcatchment of the Ringkobing Fjord catchment in Denmark. Various measures of spin-up performance were computed for model state variables such as the soil moisture and groundwater storage, as well as for diagnostic variables such as the latent and sensible heat fluxes. The impacts of initial conditions on surface water-groundwater interactions were then explored. Our analysis illustrates that the determination of an equilibrium state depends strongly on the variable and performance measure used. Choosing an improper initialization of the model can generate simulations that lead to a misinterpretation of land surface-subsurface feedback processes and result in large biases in simulated discharge. Estimated spin-up

Grip Analysis of Road Surface and Tire Footprint Using FEM

Science.gov (United States)

Sabri, M.; Abda, S.

2018-02-01

Road grip involve a touch between road pavement and the tire tread pattern. The load bearing surface, which depends on pavement roughness and local pressures in the contact patch. This research conducted to develop a Finite element model for simulating the experimentally testing of asphalt in Jl. AH Nasution Medan, North Sumatera Indonesia base on the value of grip coefficient from various tire loads and the various speed of the vehicle during contact to the road. A tire model and road pavement are developed for the analyses the geometry of tire footprint. The results showed that the greater the mass of car will increase grip coefficient. The coefficient of grip on the road surface contact trough the tire footprint strongly influence the kinetic coefficient of friction at certain speeds. Experimentally show that Concrete road grip coefficient of more than 34% compared to the asphalt road at the same IRI parameters (6-8). Kinetic friction coefficient more than 0.33 was obtained in a asphalt path at a speed of 30-40 Km/hour.

Application of Novel Lateral Tire Force Sensors to Vehicle Parameter Estimation of Electric Vehicles.

Science.gov (United States)

Nam, Kanghyun

2015-11-11

This article presents methods for estimating lateral vehicle velocity and tire cornering stiffness, which are key parameters in vehicle dynamics control, using lateral tire force measurements. Lateral tire forces acting on each tire are directly measured by load-sensing hub bearings that were invented and further developed by NSK Ltd. For estimating the lateral vehicle velocity, tire force models considering lateral load transfer effects are used, and a recursive least square algorithm is adapted to identify the lateral vehicle velocity as an unknown parameter. Using the estimated lateral vehicle velocity, tire cornering stiffness, which is an important tire parameter dominating the vehicle's cornering responses, is estimated. For the practical implementation, the cornering stiffness estimation algorithm based on a simple bicycle model is developed and discussed. Finally, proposed estimation algorithms were evaluated using experimental test data.

Effect of Tire Pressure to Physical Workload at Operating a Manual Wheelchair.

Science.gov (United States)

Booka, Masayuki; Yoneda, Ikuo; Hashizume, Tsutomu; Lee, Hokyoo; Oku, Hidehisa; Fujisawa, Shoichiro

2015-01-01

It is often experienced that low tire pressure of the wheelchair not only increases running resistance, but also reduces parking brake performance. In this study, the required driving forces for different tire pressures were experimentally measured and evaluated. It was indicated from the result that the wheelchair with proper tire pressure could be run with less workload of wheelchair-user. Then it was also indicated that the wheelchair with a lower tire pressure needed more workload of wheelchair-user even on hard level surface.

Uncontacted tire explosion causing trauma to bilateral lower extremities: A case report.

Science.gov (United States)

Yu, Ming-Yang; Su, Yun; Meng, Xiang-Jun; Luan, Bo-Wu; Gu, Gui-Shan; Sun, Qiang; Zhao, De-Wei

2017-06-01

It is uncommon for tire explosion related injuries on the lower extremity. The bilateral lower extremities were injured by tire explosion when the patient was seated in a bus. She sustained an open fracture with partial bone loss in the right calcaneus (a comminuted fracture in the right ankle joint) and a closed comminuted fracture in the left tibia and fibula. This damage was caused by uncontacted tire explosion, thanks to a thick floor between the exploded tire and the patient's feet. This type of injury on lower extremity caused by uncontacted tire explosion was uncommon. Copyright © 2017 Daping Hospital and the Research Institute of Surgery of the Third Military Medical University. Production and hosting by Elsevier B.V. All rights reserved.

Effects of studded tires on roadside airborne dust pollution in Niigata, Japan

Science.gov (United States)

Fukuzaki, Norio; Yanaka, Takaaki; Urushiyama, Yoshio

Two series of dust samples, collected by Andersen impactors (denoted by AN) and low-volume air samplers (denoted by LV), were investigated with respect to roadside airborne dusts collected in two different periods in 1983. These were the periods (i) with studded tires (February and March) and (ii) without studded tires (October). Multi-element determinations of these samples were made by neutron activation analysis and atomic absorption spectrometry. The total concentration of AN in roadside air for period (i) was about three times higher than for the period without studded tires. The lithophilic elements such as Na, Al, K, Ca, Ti, Fe and Th, and component-metal elements of stud tip, W and Ta, produced a significant increase in atmospheric concentration in winter. The contribution of pavement material, one of the most interesting components of airborne particles in this study, was related to total AN and LV by the chemical element balance method. It made up only 16 percent (9.1 μgm -3) of AN in October, compared with 46 percent (70.2 μgm -3) in February. It was also observed that the atmospheric concentrations of pavement debris to total LV decreased with the distance from the road to each sampling site.

Pavement system with rubber tire chips in subgrade

Energy Technology Data Exchange (ETDEWEB)

Ashtakala, B.; Hoque, A.K.M.M. [Concordia Univ., Montreal, PQ (Canada). Dept. of Civil Engineering

1995-12-31

A pavement design method was developed in which shredded rubber tire chips mixed with sand were used as a material for pavement subgrade. Rubber tire chips are highly compressible and produce both elastic and plastic deformations under the application of loads. Sand was added to fill the void between the tire chips and make the mixture a strong material. The design method considered the vertical compressive strain produced by the design life traffic load 18k (80 KN) repetitions. The equivalent thicknesses of the layers above the subgrade corresponding to this vertical compressive strain were determined using contour charts. From this equivalent thickness, the thicknesses for asphalt pavement, base, and sub-base were determined by Odemark`s method. 3 refs., 1 tab., 3 figs.

SPIN-UP and Preparing Undergraduate Physics Majors for Careers in Industry

Science.gov (United States)

Howes, Ruth

2011-03-01

Seven years ago, the Strategic Programs for Innovations in Undergraduate Physics (SPIN-UP) Report produced by the National Task Force on Undergraduate Physics identified several key characteristics of thriving undergraduate physics departments including steps these departments had taken to prepare students better for careers in industry. Today statistical data from AIP shows that almost 40% of students graduating with a degree in physics seek employment as soon as they graduate. Successful undergraduate physics programs have taken steps to adapt their rigorous physics programs to ensure that graduating seniors have the skills they need to enter the industrial workplace as well as to go on to graduate school in physics. Typical strategies noted during a series of SPIN-UP workshops funded by a grant from NSF to APS, AAPT, and AIP include flexible curricula, early introduction of undergraduates to research techniques, revised laboratory experiences that provide students with skills they need to move directly into jobs, and increased emphasis on ``soft'' skills such as communication and team work. Despite significant success, undergraduate programs face continuing challenges in preparing students to work in industry, most significantly the fact that there is no job called ``physicist'' at the undergraduate level. supported by grant NSF DUE-0741560.

Application of Novel Lateral Tire Force Sensors to Vehicle Parameter Estimation of Electric Vehicles

Directory of Open Access Journals (Sweden)

Kanghyun Nam

2015-11-01

Full Text Available This article presents methods for estimating lateral vehicle velocity and tire cornering stiffness, which are key parameters in vehicle dynamics control, using lateral tire force measurements. Lateral tire forces acting on each tire are directly measured by load-sensing hub bearings that were invented and further developed by NSK Ltd. For estimating the lateral vehicle velocity, tire force models considering lateral load transfer effects are used, and a recursive least square algorithm is adapted to identify the lateral vehicle velocity as an unknown parameter. Using the estimated lateral vehicle velocity, tire cornering stiffness, which is an important tire parameter dominating the vehicle’s cornering responses, is estimated. For the practical implementation, the cornering stiffness estimation algorithm based on a simple bicycle model is developed and discussed. Finally, proposed estimation algorithms were evaluated using experimental test data.

A hierarchical estimator development for estimation of tire-road friction coefficient.

Directory of Open Access Journals (Sweden)

Xudong Zhang

Full Text Available The effect of vehicle active safety systems is subject to the friction force arising from the contact of tires and the road surface. Therefore, an adequate knowledge of the tire-road friction coefficient is of great importance to achieve a good performance of these control systems. This paper presents a tire-road friction coefficient estimation method for an advanced vehicle configuration, four-motorized-wheel electric vehicles, in which the longitudinal tire force is easily obtained. A hierarchical structure is adopted for the proposed estimation design. An upper estimator is developed based on unscented Kalman filter to estimate vehicle state information, while a hybrid estimation method is applied as the lower estimator to identify the tire-road friction coefficient using general regression neural network (GRNN and Bayes' theorem. GRNN aims at detecting road friction coefficient under small excitations, which are the most common situations in daily driving. GRNN is able to accurately create a mapping from input parameters to the friction coefficient, avoiding storing an entire complex tire model. As for large excitations, the estimation algorithm is based on Bayes' theorem and a simplified "magic formula" tire model. The integrated estimation method is established by the combination of the above-mentioned estimators. Finally, the simulations based on a high-fidelity CarSim vehicle model are carried out on different road surfaces and driving maneuvers to verify the effectiveness of the proposed estimation method.

A hierarchical estimator development for estimation of tire-road friction coefficient.

Science.gov (United States)

Zhang, Xudong; Göhlich, Dietmar

2017-01-01

The effect of vehicle active safety systems is subject to the friction force arising from the contact of tires and the road surface. Therefore, an adequate knowledge of the tire-road friction coefficient is of great importance to achieve a good performance of these control systems. This paper presents a tire-road friction coefficient estimation method for an advanced vehicle configuration, four-motorized-wheel electric vehicles, in which the longitudinal tire force is easily obtained. A hierarchical structure is adopted for the proposed estimation design. An upper estimator is developed based on unscented Kalman filter to estimate vehicle state information, while a hybrid estimation method is applied as the lower estimator to identify the tire-road friction coefficient using general regression neural network (GRNN) and Bayes' theorem. GRNN aims at detecting road friction coefficient under small excitations, which are the most common situations in daily driving. GRNN is able to accurately create a mapping from input parameters to the friction coefficient, avoiding storing an entire complex tire model. As for large excitations, the estimation algorithm is based on Bayes' theorem and a simplified "magic formula" tire model. The integrated estimation method is established by the combination of the above-mentioned estimators. Finally, the simulations based on a high-fidelity CarSim vehicle model are carried out on different road surfaces and driving maneuvers to verify the effectiveness of the proposed estimation method.

78 FR 15920 - Federal Motor Vehicle Safety Standards; Tire Selection and Rims

Science.gov (United States)

2013-03-13

... [Docket No. NHTSA-2013-0030] RIN 2127-AL24 Federal Motor Vehicle Safety Standards; Tire Selection and Rims... Safety Standard (FMVSS) No. 110 to make it clear that special trailer (ST) tires are permitted to be... also proposes to exclude these trailers from a vehicle testing requirement that a tire must be retained...

Efficacy of alpha-cypermethrin and lambda-cyhalothrin applications to prevent Aedes breeding in tires.

Science.gov (United States)

Pettit, William J; Whelan, Peter I; McDonnell, Joseph; Jacups, Susan P

2010-12-01

The efficacy of alpha-cypermethrin (Cyperthor) and lambda-cyhalothrin (Demand) to prevent mosquito larval colonization of water-containing receptacles was investigated using 2 differing applications in disused car tires in Darwin, Australia. Insecticide treatments were applied uniformly to the inside surfaces of 2 categories of tires: 1) dry tires that were partially filled with water 24 h after spraying and 2) wet tires partially filled with water prior to spraying. All mosquito larvae, pupae, and dead adults were collected from the treatment and control tires weekly over the 24-wk study period and were later identified to species in the laboratory. Control tires were colonized by Aedes notoscriptus in wk 2 and by Culex quinquefasciatus in wk 4. Aedes notoscriptus failed to colonize any alpha-cypermethrin-treated tires until wk 22 and did not colonize any lambda-cyhalothrin-treated tires during the 24-wk trial. Culex quinquefasciatus colonized alpha-cypermethrin and lambda-cyhalothrin-treated tires from wk 11 and wk 15, respectively. These results indicate both insecticides using either application method can prevent colonization of Ae. notoscriptus for at least 20 wk and demonstrate great potential for the prevention of breeding in receptacles for other receptacle-breeding Aedes species, such as the dengue vectors, Ae. aegypti and Ae. albopictus.

77 FR 71679 - Bridgestone Americas Tire Operations, LLC, Receipt of Petition for Decision of Inconsequential...

Science.gov (United States)

2012-12-03

... noncompliant tires are mislabeled; the subject tires meet or exceed all performance requirements as required in...-0108; Notice 1] Bridgestone Americas Tire Operations, LLC, Receipt of Petition for Decision of... petition. SUMMARY: Bridgestone Americas Tire Operations, LLC (BRIDGESTONE),\\1\\ has determined that certain...

Strength of mortar containing rubber tire particle

Science.gov (United States)

Jusoh, M. A.; Abdullah, S. R.; Adnan, S. H.

2018-04-01

The main focus in this investigation is to determine the strength consist compressive and tensile strength of mortar containing rubber tire particle. In fact, from the previous study, the strength of mortar containing waste rubber tire in mortar has a slightly decreases compare to normal mortar. In this study, rubber tire particle was replacing on volume of fine aggregate with 6%. 9% and 12%. The sample were indicated M0 (0%), M6 (6%), M9 (9%) and M12 (12%). In this study, two different size of sample used with cube 100mm x 100mm x 100mm for compressive strength and 40mm x 40mm x 160mm for flexural strength. Morphology test was conducted by using Scanning electron microscopic (SEM) were done after testing compressive strength test. The concrete sample were cured for day 3, 7 and 28 before testing. Results compressive strength and flexural strength of rubber mortar shown improved compare to normal mortar.

Chemi-microbial processing of waste tire rubber: A project overview

International Nuclear Information System (INIS)

Romine, R.A.; Snowden-Swan, L.

1993-12-01

PNL is developing a method to use thiophillic microorganisms to devulcanize (biodesulfurize) the surface of ground rubber particles, which will improve the bonding and adhesion of the ground tire rubber into the virgin tire rubber matrix. The Chemi-microbial processing approach, introduced in this paper, is targeted at alleviating the waste tire problem in an environmentally conscious manner; it may also be applied to improve asphaltic materials and rubber and polymeric wastes to facilite their recycling. This paper outlines the logic and technical methods that will be used

Federal Research on Recycled Tire Crumb Used on Playing Fields

Science.gov (United States)

Ground rubber is recovered from scrap tires or from the tire retreading process. It is used in road construction and in athletic and recreational applications,like ground cover under playground equipment, running track material, and as a soil additive.

78 FR 54369 - The Goodyear Tire & Rubber Company, Mootness of Petition for Decision of Inconsequential...

Science.gov (United States)

2013-09-03

... subject tires meet or exceed all applicable FMVSS performance standards for a tire labeled as either load...-0107; Notice 2] The Goodyear Tire & Rubber Company, Mootness of Petition for Decision of... Petition Mootness. SUMMARY: The Goodyear Tire & Rubber Company (Goodyear),\\1\\ has determined that certain...

78 FR 9775 - Cooper Tire & Rubber Company, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2013-02-11

... subject tires in fact have more tread plies than indicated and meet or exceed all performance requirements...-0109; Notice 1] Cooper Tire & Rubber Company, Receipt of Petition for Decision of Inconsequential...: Cooper Tire & Rubber Company (Cooper),\\1\\ has determined that certain Cooper brand tires manufactured...

Tire Production and Pollution Control. Environmental Education Curriculum. Revised.

Science.gov (United States)

Topeka Public Schools, KS.

This unit was developed to introduce secondary students to the many facets of a typical, large manufacturing plant - the Topeka Goodyear Tire and Rubber Company - in an effort to increase awareness of sound environmental practices in industry. Its five major foci include the production of tires and quality control procedures; applications of…

Asperity-Level Origins of Transition from Mild to Severe Wear

Science.gov (United States)

Aghababaei, Ramin; Brink, Tobias; Molinari, Jean-François

2018-05-01

Wear is the inevitable damage process of surfaces during sliding contact. According to the well-known Archard's wear law, the wear volume scales with the real contact area and as a result is proportional to the load. Decades of wear experiments, however, show that this relation only holds up to a certain load limit, above which the linearity is broken and a transition from mild to severe wear occurs. We investigate the microscopic origins of this breakdown and the corresponding wear transition at the asperity level. Our atomistic simulations reveal that the interaction between subsurface stress fields of neighboring contact spots promotes the transition from mild to severe wear. The results show that this interaction triggers the deep propagation of subsurface cracks and the eventual formation of large debris particles, with a size corresponding to the apparent contact area of neighboring contact spots. This observation explains the breakdown of the linear relation between the wear volume and the normal load in the severe wear regime. This new understanding highlights the critical importance of studying contact beyond the elastic limit and single-asperity models.

Numerical Study of Field-reversed Configurations: The Formation and Ion Spin-up

International Nuclear Information System (INIS)

Belova, E.V.; Davidson, R.C.; Ji, H.; Yamada, M.; Cothran, C.D.; Brown, M.R.; Schaffer, M.J.

2005-01-01

Results of three-dimensional numerical simulations of field-reversed configurations (FRCs) are presented. Emphasis of this work is on the nonlinear evolution of magnetohydrodynamic (MHD) instabilities in kinetic FRCs, and the new FRC formation method by counter-helicity spheromak merging. Kinetic simulations show nonlinear saturation of the n = 1 tilt mode, where n is the toroidal mode number. The n = 2 and n = 3 rotational modes are observed to grow during the nonlinear phase of the tilt instability due to the ion spin-up in the toroidal direction. The ion toroidal spin-up is shown to be related to the resistive decay of the internal flux, and the resulting loss of particle confinement. Three-dimensional MHD simulations of counter-helicity spheromak merging and FRC formation show good qualitative agreement with results from the SSX-FRC experiment. The simulations show formation of an FRC in about 20-30 Alfven times for typical experimental parameters. The growth rate of the n = 1 tilt mode is shown to be significantly reduced compared to the MHD growth rate due to the large plasma viscosity and field-line-tying effects

Bio-inspired polymeric patterns with enhanced wear durability for microsystem applications

International Nuclear Information System (INIS)

Singh, R. Arvind; Siyuan, L.; Satyanarayana, N.; Kustandi, T.S.; Sinha, Sujeet K.

2011-01-01

At micro/nano-scale, friction force dominates at the interface between bodies moving in relative motion and severely affects their smooth operation. This effect limits the performance of microsystem devices such as micro-electro-mechanical systems (MEMS). In addition, friction force also leads to material removal or wear and thereby reduces the durability i.e. the useful operating life of the devices. In this work, we fabricated bio-inspired polymeric patterns for tribological applications. Inspired by the surface features on lotus leaves namely, the protuberances and wax, SU-8 polymeric films spin-coated on silicon wafers were topographically and chemically modified. For topographical modification, micro-scale patterns were fabricated using nanoimprint lithography and for chemical modification, the micro-patterns were coated with perfluoropolyether nanolubricant. Tribological investigation of the bio-inspired patterns revealed that the friction coefficients reduced significantly and the wear durability increased by several orders. In order to enhance the wear durability much further, the micro-patterns were exposed to argon/oxygen plasma and were subsequently coated with the perfluoropolyether nanolubricant. Bio-inspired patterns with enhanced wear durability, such as the ones investigated in the current work, have potential tribological applications in MEMS/Bio-MEMS actuator-based devices. Highlights: →Bio-inspired polymeric patterns for tribological applications in microsystems. →Novel surface modification for the patterns to enhance tribological properties. →Patterns show low friction properties and extremely high wear durability.

75 FR 17830 - Continental Tire North America, Inc., Receipt of Petition for Decision of Inconsequential...

Science.gov (United States)

2010-04-07

... safety as it ``does not affect the safety, performance and durability of the tire; the tires were built... requirements. Continental said that it performs ongoing compliance testing ``to assure tire performance'' and that ``all tires included in this petition will meet or exceed the performance requirements of FMVSS...

The Implementation of Quality Function Deployment (QFD in Tire Industry

Directory of Open Access Journals (Sweden)

Hari Abdul Hadi

2017-12-01

Full Text Available This research had two main objectives. The first research objective was to make the right design of new product according to customer requirements with the implementation of Quality Function Deployment (QFD in the tire industry. The second research objective was to enhance competitiveness based on the renewal of marketing strategy and consumer needs, non-explosive prohibition, non-slip tires, no bulgy, and competitive prices. The research was carried out by using costumer satisfaction rating by comparing with the competitor companies. Based on calculation using QFD method, it shows that split liner has the highest percentage of technical requirement in tire industry about 30,57%. The second factor is pattern design about 25,98%. Then, the third factor is compound technology about 22,68%. Therefore, the researchers can recommend several strategies for the quality improvement based on customer needs for the tire industry.

Dental wear, wear rate, and dental disease in the African apes.

Science.gov (United States)

Elgart, Alison A

2010-06-01

The African apes possess thinner enamel than do other hominoids, and a certain amount of dentin exposure may be advantageous in the processing of tough diets eaten by Gorilla. Dental wear (attrition plus abrasion) that erodes the enamel exposes the underlying dentin and creates additional cutting edges at the dentin-enamel junction. Hypothetically, efficiency of food processing increases with junction formation until an optimal amount is reached, but excessive wear hinders efficient food processing and may lead to sickness, reduced fecundity, and death. Occlusal surfaces of molars and incisors in three populations each of Gorilla and Pan were videotaped and digitized. The quantity of incisal and molar occlusal dental wear and the lengths of dentin-enamel junctions were measured in 220 adult and 31 juvenile gorilla and chimpanzee skulls. Rates of dental wear were calculated in juveniles by scoring the degree of wear between adjacent molars M1 and M2. Differences were compared by principal (major) axis analysis. ANOVAs compared means of wear amounts. Pearson correlation coefficients were calculated to compare the relationship between molar wear and incidence of dental disease. Results indicate that quantities of wear are significantly greater in permanent incisors and molars and juvenile molars of gorillas compared to chimpanzees. The lengths of dentin-enamel junctions were predominantly suboptimal. Western lowland gorillas have the highest quantities of wear and the most molars with suboptimal wear. The highest rates of wear are seen in Pan paniscus and Pan t. troglodytes, and the lowest rates are found in P.t. schweinfurthii and G. g. graueri. Among gorillas, G. b. beringei have the highest rates but low amounts of wear. Coefficients between wear and dental disease were low, but significant when all teeth were combined. Gorilla teeth are durable, and wear does not lead to mechanical senescence in this sample.

Vibration Analysis of a Tire in Ground Contact under Varied Conditions

Directory of Open Access Journals (Sweden)

Karakus Murat

2017-03-01

Full Text Available The effect of three different factors, which are inflation pressure, vertical load and coefficient of friction on the natural frequencies of a tire (175/70 R13 has been studied. A three dimensional tire model is constructed, using four different material properties and parts in the tire. Mechanical properties of the composite parts are evaluated. After investigating the free vibration, contact analysis is carried out. A concrete block and the tire are modelled together, using three different coefficients of friction. Experiments are run under certain conditions to check the accuracy of the numerical model. The natural frequencies are measured to describe free vibration and vibration of the tire contacted by ground, using a damping monitoring method. It is seen, that experimental and numerical results are in good agreement. On the other hand, investigating the impact of three different factors together is quite difficult on the natural frequencies. When some of these factors are assumed to be constant and the variables are taken one by one, it is easier to assess the effects.

Effects of tire leachate on the invasive mosquito Aedes albopictus and the native congener Aedes triseriatus

Directory of Open Access Journals (Sweden)

Oswaldo C. Villena

2017-09-01

Full Text Available Discarded vehicle tire casings are an important artificial habitat for the developmental stages of numerous vector mosquitoes. Discarded vehicle tires degrade under ultraviolet light and leach numerous soluble metals (e.g., barium, cadmium, zinc and organic substances (e.g., benzothiazole and its derivatives [BZTs], polyaromatic hydrocarbons [PAHs] that could affect mosquito larvae that inhabit the tire casing. This study examined the relationship between soluble zinc, a common marker of tire leachate, on mosquito densities in tire habitats in the field, and tested the effects of tire leachate on the survival and development of newly hatched Aedes albopictus and Aedes triseriatus larvae in a controlled laboratory dose-response experiment. In the field, zinc concentrations were as high as 7.26 mg/L in a single tire and averaged as high as 2.39 (SE ± 1.17 mg/L among tires at a single site. Aedes albopictus (37/42 tires, 81.1% and A. triseriatus (23/42, 54.8% were the most widespread mosquito species, co-occurred in over half (22/42, 52.4% of all tires, and A. triseriatus was only collected without A. albopictus in one tire. Aedes triseriatus was more strongly negatively associated with zinc concentration than A. albopictus, and another common mosquito, C. pipiens, which was found in 17 tires. In the laboratory experiment, A. albopictus per capita rate of population change (λ′ was over 1.0, indicating positive population growth, from 0–8.9 mg/L zinc concentration (0–10,000 mg/L tire leachate, but steeply declined to zero from 44.50–89.00 mg/L zinc (50,000–100,000 mg/L tire leachate. In contrast, A. triseriatus λ′ declined at the lower concentration of 0.05 mg/L zinc (100 mg/L tire leachate, and was zero at 0.45, 8.90, 44.50, and 89.00 mg/L zinc (500, 10,000, 50,000 and 100,000 mg/L tire leachate. These results indicate that tire leachate can have severe negative effects on populations of container-utilizing mosquitoes at

Sensor set-up for wireless measurement of automotive rim and wheel parameters in laboratory conditions

Science.gov (United States)

Borecki, M.; Prus, P.; Korwin-Pawlowski, M. L.; Rychlik, A.; Kozubel, W.

2017-08-01

Modern rims and wheels are tested at the design and production stages. Tests can be performed in laboratory conditions and on the ride. In the laboratory, complex and costly equipment is used, as for example wheel balancers and impact testers. Modern wheel balancers are equipped with electronic and electro-mechanical units that enable touch-less measurement of dimensions, including precision measurement of radial and lateral wheel run-out, automatic positioning and application of the counterweights, and vehicle wheel set monitoring - tread wear, drift angles and run-out unbalance. Those tests are performed by on-wheel axis measurements with laser distance meters. The impact tester enables dropping of weights from a defined height onto a wheel. Test criteria are the loss of pressure of the tire and generation of cracks in the wheel without direct impact of the falling weights. In the present paper, a set up composed of three accelerometers, a temperature sensor and a pressure sensor is examined as the base of a wheel tester. The sensor set-up configuration, on-line diagnostic and signal transmission are discussed.

A brief description of the biomechanics and physiology of a strongman event: the tire flip.

Science.gov (United States)

Keogh, Justin W L; Payne, Amenda L; Anderson, Brad B; Atkins, Paul J

2010-05-01

The purpose of this study was to (a) characterize the temporal aspects of a popular strongman event, the tire flip; (b) gain some insight into the temporal factors that could distinguish the slowest and fastest flips; and (c) obtain preliminary data on the physiological stress of this exercise. Five resistance-trained subjects with experience in performing the tire flip gave informed consent to participate in this study. Each subject performed 2 sets of 6 tire flips with a 232-kg tire with 3 minutes of rest between sets. Temporal variables were obtained from video cameras positioned 10 m from the tire, perpendicular to the intended direction of the tire flip. Using the "stopwatch" function in Silicon Coach, the duration of each tire flip and that of the first pull, second pull, transition, and push phases were recorded. Physiological stress was estimated via heart rate and finger-prick blood lactate response. Independent T-tests revealed that the 2 faster subjects (0.38 +/- 0.17 s) had significantly (p tire flip performance and that this exercise provides relatively high degrees of physiological stress.

Economic and policy instrument analyses in support of the scrap tire recycling program in Taiwan.

Science.gov (United States)

Chang, Ni-Bin

2008-02-01

Understanding the cost-effectiveness and the role of economic and policy instruments, such as the combined product tax-recycling subsidy scheme or a tradable permit, for scrap tire recycling has been of crucial importance in a market-oriented environmental management system. Promoting product (tire) stewardship on one hand and improving incentive-based recycling policy on the other hand requires a comprehensive analysis of the interfaces and interactions in the nexus of economic impacts, environmental management, environmental valuation, and cost-benefit analysis. This paper presents an assessment of the interfaces and interactions between the implementation of policy instruments and its associated economic evaluation for sustaining a scrap tire recycling program in Taiwan during the era of the strong economic growth of the late 1990s. It begins with an introduction of the management of the co-evolution between technology metrics of scrap tire recycling and organizational changes for meeting the managerial goals island-wide during the 1990s. The database collected and used for such analysis covers 17 major tire recycling firms and 10 major tire manufacturers at that time. With estimates of scrap tire generation and possible scale of subsidy with respect to differing tire recycling technologies applied, economic analysis eventually leads to identify the associated levels of product tax with respect to various sizes of new tires. It particularly demonstrates a broad perspective of how an integrated econometric and engineering economic analysis can be conducted to assist in implementing policy instruments for scrap tire management. Research findings indicate that different subsidy settings for collection, processing, and end use of scrap tires should be configured to ameliorate the overall managerial effectiveness. Removing the existing boundaries between designated service districts could strengthen the competitiveness of scrap tires recycling industry, helping to

Impacts of environmental conditions on the sorption of volatile organic compounds onto tire powder

Energy Technology Data Exchange (ETDEWEB)

Oh, Dong I. [Division of R and D Planning and Management, Korea Institute of Environmental Science and Technology, Seoul (Korea, Republic of); Nam, Kyongphile [School of Civil, Urban and Geosystem Engineering, College of Engineering, Seoul National University, Gwanak-Ku, 151-742 Seoul (Korea, Republic of); Park, Jae W. [Department of Civil Engineering, Hanyang University, Seoul (Korea, Republic of); Khim, Jee H. [Department of Civil and Environmental Engineering, Korea University, Seoul (Korea, Republic of); Kim, Yong K. [School of Civil, Urban and Geosystem Engineering, College of Engineering, Seoul National University, Gwanak-Ku, 151-742 Seoul (Korea, Republic of); Kim, Jae Y. [School of Civil, Urban and Geosystem Engineering, College of Engineering, Seoul National University, Gwanak-Ku, 151-742 Seoul (Korea, Republic of)], E-mail: jaeykim@snu.ac.kr

2008-05-01

A series of batch tests were performed and the impacts of environmental conditions and phase change on the sorption of volatile organic compounds (VOCs) were investigated. Benzene, trichloroethylene, tetrachloroethylene, and ethylbenzene were selected as target VOCs. Sorption of VOCs onto tire powder was well demonstrated by a linear-partitioning model. Water-tire partition coefficients of VOCs (not tested in this study) could be estimated using a logarithmic relationship between observed water-tire partition coefficients and octanol-water partition coefficients of the VOCs tested. The target VOCs did not seem to compete with other VOCs significantly when sorbed onto the tire powder for the range of concentrations tested. The influence of environmental conditions, such as pH and ionic strength also did not seem to be significant. Water-tire partition coefficients of benzene, trichloroethylene, tetrachloroethylene, and ethylbenzene decreased as the sorbent dosage increased. However, they showed stable values when the sorbent dosage was greater than 10 g/L. Air-tire partition coefficient could be extrapolated from Henry's law constants and water-tire partition coefficient of VOCs.

Impacts of environmental conditions on the sorption of volatile organic compounds onto tire powder

International Nuclear Information System (INIS)

Oh, Dong I.; Nam, Kyongphile; Park, Jae W.; Khim, Jee H.; Kim, Yong K.; Kim, Jae Y.

2008-01-01

A series of batch tests were performed and the impacts of environmental conditions and phase change on the sorption of volatile organic compounds (VOCs) were investigated. Benzene, trichloroethylene, tetrachloroethylene, and ethylbenzene were selected as target VOCs. Sorption of VOCs onto tire powder was well demonstrated by a linear-partitioning model. Water-tire partition coefficients of VOCs (not tested in this study) could be estimated using a logarithmic relationship between observed water-tire partition coefficients and octanol-water partition coefficients of the VOCs tested. The target VOCs did not seem to compete with other VOCs significantly when sorbed onto the tire powder for the range of concentrations tested. The influence of environmental conditions, such as pH and ionic strength also did not seem to be significant. Water-tire partition coefficients of benzene, trichloroethylene, tetrachloroethylene, and ethylbenzene decreased as the sorbent dosage increased. However, they showed stable values when the sorbent dosage was greater than 10 g/L. Air-tire partition coefficient could be extrapolated from Henry's law constants and water-tire partition coefficient of VOCs

Wear monitoring of protective nitride coatings using image processing

DEFF Research Database (Denmark)

Rasmussen, Inge Lise; Guibert, M.; Belin, M.

2010-01-01

-meter with up to 105 19 repetitive cycles, eventually leaving the embedded TiN signal layer uncovered at the bottom the wear scar. 20 The worn surface was characterized by subsequent image processing. A color detection of the wear scar with 21 the exposed TiN layer by a simple optical imaging system showed......A double-layer model system, consisting of a thin layer of tribological titanium aluminum nitride (TiAlN) on 17 top of titanium nitride (TiN), was deposited on polished 100Cr6 steel substrates. The TiAlN top-coatings 18 were exposed to abrasive wear by a reciprocating wear process in a linear tribo...... a significant increase up to a factor of 2 of 22 the relative color values from the TiAlN top layers to the embedded TiN signal layers. This behavior agrees 23 well with the results of reflectance detection experiment with a red laser optical system on the same system. 24 Thus we have demonstrated that image...

Characterization of Semi-Volatile Organic Chemicals from Tire Crumb Rubber

Science.gov (United States)

Recycled tire crumb rubber (TCR) is often used as infill material in synthetic turf playing fields as well as some playgrounds. Concerns have been raised about the safety of this material and a multi-agency Federal Research Action Plan on Recycled Tire Crumb Used on Playing Field...

Vehicle Unsteady Dynamics Characteristics Based on Tire and Road Features

Directory of Open Access Journals (Sweden)

Bin Ma

2013-01-01

Full Text Available During automotive related accidents, tire and road play an important role in vehicle unsteady dynamics as they have a significant impact on the sliding friction. The calculation of the rubber viscoelastic energy loss modulus and the true contact area model is improved based on the true contact area and the rubber viscoelastic theory. A 10 DOF full vehicle dynamic model in consideration of the kinetic sliding friction coefficient which has good accuracy and reality is developed. The stability test is carried out to evaluate the effectiveness of the model, and the simulation test is done in MATLAB to analyze the impact of tire feature and road self-affine characteristics on the sport utility vehicle (SUV unsteady dynamics under different weights. The findings show that it is a great significance to analyze the SUV dynamics equipped with different tire on different roads, which may provide useful insights into solving the explicit-implicit features of tire prints in systematically and designing active safety systems.

Predicting railway wheel wear under uncertainty of wear coefficient, using universal kriging

International Nuclear Information System (INIS)

Cremona, Marzia A.; Liu, Binbin; Hu, Yang; Bruni, Stefano; Lewis, Roger

2016-01-01

Railway wheel wear prediction is essential for reliability and optimal maintenance strategies of railway systems. Indeed, an accurate wear prediction can have both economic and safety implications. In this paper we propose a novel methodology, based on Archard's equation and a local contact model, to forecast the volume of material worn and the corresponding wheel remaining useful life (RUL). A universal kriging estimate of the wear coefficient is embedded in our method. Exploiting the dependence of wear coefficient measurements with similar contact pressure and sliding speed, we construct a continuous wear coefficient map that proves to be more informative than the ones currently available in the literature. Moreover, this approach leads to an uncertainty analysis on the wear coefficient. As a consequence, we are able to construct wear prediction intervals that provide reasonable guidelines in practice. - Highlights: • Wear prediction is of outmost importance for reliability of railway systems. • Wear coefficient is essential in prediction through Archard's equation. • A novel methodology is developed to predict wear and RUL. • Universal kriging is used for wear coefficient and uncertainty estimation. • A simulation study and a real case application are provided.

Increased efficiency in the second-hand tire trade provides opportunity for dengue control.

Science.gov (United States)

Pliego Pliego, Emilene; Velázquez-Castro, Jorge; Eichhorn, Markus P; Fraguela Collar, Andrés

2018-01-21

Dengue fever is increasing in geographical range, spread by invasion of its vector mosquitoes. The trade in second-hand tires has been implicated as a factor in this process because they act as mobile reservoirs of mosquito eggs and larvae. Regional transportation of tires can create linkages between rural areas with dengue and disease-free urban areas, potentially giving rise to outbreaks even in areas with strong local control measures. In this work we sought to model the dynamics of mosquito transportation via the tire trade, in particular to predict its role in causing unexpected dengue outbreaks through vertical transmission of the virus across generations of mosquitoes. We also aimed to identify strategies for regulating the trade in second-hand tires, improving disease control. We created a mathematical model which captures the dynamics of dengue between rural and urban areas, taking into account the movement and storage time of tires, and mosquito diapause. We simulate a series of scenarios in which a mosquito population is introduced to a dengue-free area via movement of tires, either as single or multiple events, increasing the likelihood of a dengue outbreak. A persistent disease state can be induced regardless of whether urban conditions for an outbreak are met, and an existing endemic state can be enhanced by vector input. Finally we assess the potential for regulation of tire processing as a means of reducing the transmission of dengue fever using a specific case study from Puerto Rico. Our work demonstrates the importance of the second-hand tire trade in modulating the spread of dengue fever across regions, in particular its role in introducing dengue to disease-free areas. We propose that reduction of tire storage time and control of their movement can play a crucial role in containing dengue outbreaks. Copyright © 2017 Elsevier Ltd. All rights reserved.

Spinning-Up: the Case of the Symbiotic X-Ray Binary 3A 1954+319

Science.gov (United States)

Fuerst, F.; Marcu, D. M.; Pottschmidt, K.; Grinberg, V.; Wilms, J.; CadolleBel, M.

2011-01-01

We present a timing and spectral analysis of the variable X-ray source 3A 1954+319. Our analysis is mainly based on an outburst serendipitously observed during INTEGRAL Key Program observations of the Cygnus region in 2008 fall and on the Swift/BAT longterm light curve. Previous observations, though sparse, have identified the source to be one of only nine known symbiotic X-ray binaries, i.e., systems composed of an accreting neutron star orbiting in a highly inhomogeneous medium around an M-giant companion. The spectrum of3A 1954+319 above > 20 keV can be best described by a broken power law model. The extremely long pulse period of approx.5.3 hours is clearly visible in the INTEGRAL/ISGRI light curve and confirmed through an epoch folding period search. Furthermore, the light curve allows us to determine a very strong spin up of -2 x 10(exp -4) h/h during the outburst. This spin up is confirmed by the pulse period evolution calculated from Swift/BAT data. The Swift/BAT data also show a long spin-down trend prior to the 2008 outburst, which is confirmed in archival INTEGRAL/ISGRI data. We discuss possible accretion models and geometries allowing for the transfer of such large amounts of angular momentum and investigate the harder spectrum of this outburst compared to previously published results.

Numerical Study of Tire Hydroplaning Based on Power Spectrum of Asphalt Pavement and Kinetic Friction Coefficient

Directory of Open Access Journals (Sweden)

Shengze Zhu

2017-01-01

Full Text Available Hydroplaning is a driving phenomenon threating vehicle’s control stability and safety. It happens when tire rolls on wet pavement with high speed that hydrodynamic force uplifts the tire. Accurate numerical simulation to reveal the mechanism of hydroplaning and evaluate the function of relevant factors in this process is significant. In order to describe the friction behaviors of tire-pavement interaction, kinetic friction coefficient curve of tire rubber and asphalt pavement was obtained by combining pavement surface power spectrum and complex modulus of tread rubber through Persson’s friction theory. Finite element model of tire-fluid-pavement was established in ABAQUS, which was composed of a 225-40-R18 radial tire and three types of asphalt pavement covered with water film. Mechanical responses and physical behaviors of tire-pavement interaction were observed and compared with NASA equation to validate the applicability and accuracy of this model. Then contact force at tire-pavement interface and critical hydroplaning speed influenced by tire inflation pressure, water film thickness, and pavement types were investigated. The results show higher tire inflation pressure, thinner water film, and more abundant macrotexture enhancing hydroplaning speed. The results could be applied to predict hydroplaning speed on different asphalt pavement and improve pavement skid resistance design.

Evaluation of moisture damage in asphalt concrete with CRM motorcycle tire waste passing #50 sieve size

Science.gov (United States)

Siswanto, Henri; Supriyanto, Bambang; Pranoto, Pranoto; Chandra, Pria Rizky; Hakim, Arief Rahman

2017-09-01

The objective of this experimental research is to evaluate moisture damage in Asphalt Concrete (AC) with Crumb Rubber Modified (CRM) motorcycle tire waste passing #50 and retaining #100 sieve size. Two gradations were used in this research, the first gradation is usual for asphalt concrete base (ACB) and the second gradation is for asphalt concrete wearing course (ACWC). Marshall testing apparatus was used for testing the Marshall specimens. Seven levels of CRM content were used, namely 0%, 0.5%, 1%, 1.5%, 3%, 4.5% and 6% by weight of mixtures. Retained stability represent the level of moisture damage of AC pavement. The result indicates that addition CRM to the AC mixture increases their the stability to a maximum value and subsequent addition decrease the stability. The addition CRM to AC decreases their moisture damage susceptibility. AC with 1% CRM is the best asphalt-CRM mix.

Perfect sound insulation property of reclaimed waste tire rubber

Science.gov (United States)

Ubaidillah, Harjana, Yahya, Iwan; Kristiani, Restu; Muqowi, Eki; Mazlan, Saiful Amri

2016-03-01

This article reports an experimental investigation of sound insulation and absorption performance of a materials made of reclaimed ground tire rubber which is known as un-recyclable thermoset. The bulk waste tire is processed using single step recycling methods namely high-pressure high-temperature sintering (HPHTS). The bulk waste tire is simply placed into a mold and then a pressure load of 3 tons and a heating temperature of 200°C are applied to the mold. The HPHTS conducted for an hour and then it is cooled in room temperature. The resulted product is then evaluated the acoustical properties namely sound transmission loss (STL) and sound absorption coefficient using B&K Tube Kit Type 4206-T based on ISO 10534-2, ASTM E1050 and ASTM E2611. The sound absorption coefficient is found about 0.04 until 0.08 while STL value ranges between 50 to 60 dB. The sound absorption values are found to be very low (<0.1), while the average STL is higher than other elastomeric matrix found in previous work. The reclaimed tire rubber through HPHTS technique gives good soundproof characteristic.

Chromium removal from water by activated carbon developed from waste rubber tires.

Science.gov (United States)

Gupta, Vinod Kumar; Ali, Imran; Saleh, Tawfik A; Siddiqui, M N; Agarwal, Shilpi

2013-03-01

Because of the continuous production of large amount of waste tires, the disposal of waste tires represents a major environmental issue throughout the world. This paper reports the utilization of waste tires (hard-to-dispose waste) as a precursor in the production of activated carbons (pollution-cleaning adsorbent). In the preparation of activated carbon (AC), waste rubber tire (WRT) was thermally treated and activated. The tire-derived activated carbon was characterized by means of scanning electron microscope, energy-dispersive X-ray spectroscopy, FTIR spectrophotometer, and X-ray diffraction. In the IR spectrum, a number of bands centred at about 3409, 2350, 1710, 1650, and 1300-1000 cm(-1) prove the present of hydroxyl and carboxyl groups on the surface of AC in addition to C═C double bonds. The developed AC was tested and evaluated as potential adsorbent removal of chromium (III). Experimental parameters, such as contact time, initial concentration, adsorbent dosage and pH were optimized. A rapid uptake of chromium ions was observed and the equilibrium is achieved in 1 h. It was also found that the adsorption process is pH dependent. This work adds to the global discussion of the cost-effective utilization of waste rubber tires for waste water treatment.

Assessment of wear dependence parameters in complex model of cutting tool wear

Science.gov (United States)

Antsev, A. V.; Pasko, N. I.; Antseva, N. V.

2018-03-01

This paper addresses wear dependence of the generic efficient life period of cutting tools taken as an aggregate of the law of tool wear rate distribution and dependence of parameters of this law's on the cutting mode, factoring in the random factor as exemplified by the complex model of wear. The complex model of wear takes into account the variance of cutting properties within one batch of tools, variance in machinability within one batch of workpieces, and the stochastic nature of the wear process itself. A technique of assessment of wear dependence parameters in a complex model of cutting tool wear is provided. The technique is supported by a numerical example.

Spin-polarization and spin-dependent logic gates in a double quantum ring based on Rashba spin-orbit effect: Non-equilibrium Green's function approach

International Nuclear Information System (INIS)

Eslami, Leila; Esmaeilzadeh, Mahdi

2014-01-01

Spin-dependent electron transport in an open double quantum ring, when each ring is made up of four quantum dots and threaded by a magnetic flux, is studied. Two independent and tunable gate voltages are applied to induce Rashba spin-orbit effect in the quantum rings. Using non-equilibrium Green's function formalism, we study the effects of electron-electron interaction on spin-dependent electron transport and show that although the electron-electron interaction induces an energy gap, it has no considerable effect when the bias voltage is sufficiently high. We also show that the double quantum ring can operate as a spin-filter for both spin up and spin down electrons. The spin-polarization of transmitted electrons can be tuned from −1 (pure spin-down current) to +1 (pure spin-up current) by changing the magnetic flux and/or the gates voltage. Also, the double quantum ring can act as AND and NOR gates when the system parameters such as Rashba coefficient are properly adjusted

Dielectric properties of various polymers (PVC, EVA, HDPE, and PP) reinforced with ground tire rubber (GTR)

OpenAIRE

Mujal Rosas, Ramón María; Marín Genescá, Marcos; Ballart Prunell, Jordi

2015-01-01

Mass production of tires as well as its difficult storage or elimination is a real environmental problem. Various methods for recycling tires are currently used, such as mechanical crushing, which puts vulcanized rubber, steel, and fibers apart. The rubber may be used in several industrial applications such as flooring, insulations, and footwear. The present paper focuses on finding a new application for old used tires [ground tire rubber (GTR)]. To this end, tires dust has been mixed with va...

Prospective of Macedonia for treatment and recycling of tire waste with Pirolitic process

Directory of Open Access Journals (Sweden)

Sarafov Victor

2017-01-01

Full Text Available The automotive industry is one of the ever-developing branches of modern society and therefore collecting and recycling of old tires must not be ignored. It must be taken into consideration that tire waste is decomposing at an extremely low pace under the influence of climate factors, that waste from used tires not only is covering large areas, but there is also a possibility of spontaneous fire that is usually long-lasting and emits gasses that have negative effect on human health. Tires are made of complex polymeric materials and contain chemical additives. When burning tires on an open field highly toxic and cancerous organic compounds are being released (biphenyl, anthracene, fluoranthene and other toxins. Pyrolysis is a process that offers sustainable management of this type of waste which in continuation is to be explained in detail.

75 FR 28319 - Yokohama Tire Corporation, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2010-05-20

... concludes in part that ``the actual tire performance is not inconsequential as it relates to motor vehicle safety because the actual tire performance is not affected by this noncompliance, and in the unlikely...-0056; Notice 1] Yokohama Tire Corporation, Receipt of Petition for Decision of Inconsequential...

Analysis of Tire Tractive Performance on Deformable Terrain by Finite Element-Discrete Element Method

Science.gov (United States)

Nakashima, Hiroshi; Takatsu, Yuzuru

The goal of this study is to develop a practical and fast simulation tool for soil-tire interaction analysis, where finite element method (FEM) and discrete element method (DEM) are coupled together, and which can be realized on a desktop PC. We have extended our formerly proposed dynamic FE-DE method (FE-DEM) to include practical soil-tire system interaction, where not only the vertical sinkage of a tire, but also the travel of a driven tire was considered. Numerical simulation by FE-DEM is stable, and the relationships between variables, such as load-sinkage and sinkage-travel distance, and the gross tractive effort and running resistance characteristics, are obtained. Moreover, the simulation result is accurate enough to predict the maximum drawbar pull for a given tire, once the appropriate parameter values are provided. Therefore, the developed FE-DEM program can be applied with sufficient accuracy to interaction problems in soil-tire systems.

[Particle numbers in classified sizes of roadside dust caused by studded tires in the air at different heights from the pavement surface].

Science.gov (United States)

Sato, T; Niioka, T; Kurasaki, M; Kojima, Y

1996-07-01

Increased use of motor vehicles has produced various risks to human health due to air pollution by noxious gases, heavy metals and roadside dust. Since the late 1970s, the wide spread use of studded tires for cars has caused pavement wear, resulting in not only economic losses, but also roadside air pollution in cold and snowy regions in Japan. The most serious environmental problem in Sapporo, a city with heavy snowfall, in the 1980s, was roadside dust derived from studded tires. The inhabitants suffered from this dust in the early winter and in the early spring when the streets were not covered with snow. To investigate the influence of such roadside dust upon human health, particle numbers in classified sizes of roadside dust were counted after the roadside dust in the air was collected with a device we constructed at 30, 60, 90, 120, 150, and 180 cm above the pavement surface. The results indicated that the concentration of roadside dust in the air did not greatly vary according to the height from the pavement surface. The results also suggested that xenogranuloma, reported in lungs of stray dogs, under roadside dust-pollution conditions such as those examined here, may occur in humans in the future.

Wear of human enamel: a quantitative in vitro assessment.

Science.gov (United States)

Kaidonis, J A; Richards, L C; Townsend, G C; Tansley, G D

1998-12-01

Many factors influence the extent and rate at which enamel wears. Clinical studies in humans are limited by difficulties in the accurate quantification of intra-oral wear and by a lack of control over the oral environment. The purpose of this study was to determine the wear characteristics of human dental enamel under controlled experimental conditions. An electro-mechanical tooth wear machine, in which opposing enamel surfaces of sectioned, extracted teeth were worn under various conditions, was used to simulate tooth grinding or bruxism. Enamel surface wear was quantified by weight to an accuracy of 0.1 mg, with water uptake and loss controlled. The variables considered included the structure and hardness of enamel, facet area, duration of tooth contact, relative speed of opposing surfaces, temperature, load, pH, and the nature of the lubricant. Enamel wear under non-lubricated conditions increased with increasing load over the range of 1.7 to 16.2 kg. The addition of a liquid lubricant (pH = 7) reduced enamel wear up to 6.7 kg, but when the load increased above this threshold, the rate of wear increased dramatically. With the viscosity of the lubricant constant and pH = 3, the rate of wear was further reduced to less than 10% of the non-lubricated rate at 9.95 kg, after which the rate again increased substantially. Under more extreme conditions (pH = 1.2, simulating gastric acids), the wear was excessive under all experimental loads. When saliva was used as a lubricant, the amount of wear was relatively low at 9.95 kg, but rapid wear occurred at 14.2 kg and above. These results indicate that under non-lubricated conditions, enamel wear remains low at high loads due to the dry-lubricating capabilities of fine enamel powder. Under lubricated conditions, low loads with an acidic lubricant lead to little enamel wear, whereas very low pH results in a high rate of wear under all loads.

Toward using tire-road contact stresses in pavement design and analysis

CSIR Research Space (South Africa)

De Beer, Morris

2012-10-01

Full Text Available pavement design. Four different tire models were used to represent a single tire type in order to demonstrate its effect on road pavement response of a typical South African pavement structure. Only applied vertical stress was used for the analyses...

Prediction of properties of polymer concrete composite with tire rubber using neural networks

International Nuclear Information System (INIS)

Diaconescu, Rodica-Mariana; Barbuta, Marinela; Harja, Maria

2013-01-01

Highlights: ► Using waste a new composite material was obtained with specific characteristics. ► The objective was to maximize tire powder content with the minimum resin content. ► By direct modeling, the maximum compressive strength was obtained for 30% tire powder. ► Inverse neural modeling was used for obtaining maximum values of strengths. -- Abstract: The neural network method was used to investigate the influence of filler and resin content on the mechanical properties of polymer concrete with powdered tire waste. The mechanical strengths of 10 experimentally determined combinations using mixed epoxy resin, aggregates and tire powder as filler were optimized using direct neural modeling and inverse neural modeling, by imposing a minimum cost (content in resin). Direct neural modeling gave the optimum composition for obtaining maximum values for compressive strength, flexural strength and split tensile strength. Inverse neural modeling analyzed the possibility of obtaining maximum values of mechanical properties by variations in the dosages of the epoxy resin and tire powder. Neural network modeling generated the mixes with the lowest cost and maximum strength. The modeling method has shown that two mechanical properties can be simultaneously optimized in the investigation domain. From direct modeling, the maximum compressive strength was obtained for a composition with 0.215 (fraction weight) epoxy resin and 0.3 (fraction weight) tire powder. Maximum flexural strength was obtained for experimental values of 0.23 epoxy resin and 0.17 tire powder with a severe reduction noted for smaller resin dosages. The maximum split tensile strength was obtained for a resin dosage of 0.24 and tire powder dosage of 0.17

Nuclear spin warm up in bulk n -GaAs

Science.gov (United States)

Kotur, M.; Dzhioev, R. I.; Vladimirova, M.; Jouault, B.; Korenev, V. L.; Kavokin, K. V.

2016-08-01

We show that the spin-lattice relaxation in n -type insulating GaAs is dramatically accelerated at low magnetic fields. The origin of this effect, which cannot be explained in terms of well-known diffusion-limited hyperfine relaxation, is found in the quadrupole relaxation, induced by fluctuating donor charges. Therefore, quadrupole relaxation, which governs low field nuclear spin relaxation in semiconductor quantum dots, but was so far supposed to be harmless to bulk nuclei spins in the absence of optical pumping, can be studied and harnessed in the much simpler model environment of n -GaAs bulk crystal.

Impact of tire debris on in vitro and in vivo systems

Directory of Open Access Journals (Sweden)

Vismara Claudio

2005-03-01

Full Text Available Abstract Background It is estimated that over 80% of respirable particulate matter (PM10 in cities comes from road transport and that tire and brake wear are responsible for the 3–7% emission of it. Data on the indicators of environmental impact of tire debris (TD, originated from the tire abrasion on roads, are extremely scarce, even though TD contains chemicals (zinc and organic compounds which can be released in the environment. Methods TD particle morphology was analysed with SEM, TEM and FIB instruments. TD eluates and TD organic extracts were tested at dilution series on human cell lines and Xenopus laevis embryos. 50 and 100 g/L TD were used for the eluates obtained after 24 h at pH 3 and the quantity of zinc present was measured with a ICP-AES. Eluates diluted to 1%, 10%, 50% in culture media and undiluted were used on X. laevis embryos in the FETAX test. HepG2 cells were exposed for 24 h to 0.05 – 50 μg/ml of zinc salt while A549 cells were exposed for 24, 48 and 72 h to 10, 50, 60, or 75 μg/ml of TD extract. X. laevis embryos were exposed to 50, 80, 100, or 120 μg/ml TD extract. Results The solution of undiluted 50 g/L TD produced 80.2% mortality (p X. laevis embryos and this toxic effect was three times greater than that produced by 100 g/L TD. Zn accumulation in HepG2 cells was evident after 4 h exposure. A549 cells exposed to TD organic extract for 72 h presented a modified morphology, a decrease in cell proliferation and an increase in DNA damage as shown by comet assay. The dose 80 μg/ml of TD extract produced 14.6% mortality in X. laevis embryos and 15.9% mortality at 120 μg/ml. Treatment with 80, 100, or 120 μg/ml TD organic extract increased from 14.8% to 37.8% malformed larvae percentages compared to 5.6% in the control. Conclusion Since the amount of Zn leached from TD is related to pH, aggregation of particles and elution process, the quantity of TD present in the environment has to be taken into account. Moreover

The space shuttle program from challenge to achievement: Space exploration rolling on tires

Science.gov (United States)

Felder, G. L.

1985-01-01

The Space Shuttle Transportation System is the first space program to employ the pneumatic tire as a part of space exploration. For aircraft tires, this program establishes new expectations as to what constitutes acceptable performance within a set of tough environmental and operational conditions. Tire design, stresses the usual low weight, high load, high speed, and excellent air retention features but at extremes well outside industry standards. Tires will continue to be an integral part of the Shuttle's landing phase in the immediate future since they afford a unique combination of directional control, braking traction, flotation and shock absorption not available by other systems.

75 FR 68855 - Pirelli Tire LLC, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2010-11-09

... noncompliance has an inconsequential effect on tire performance and motor vehicle safety because all of the affected tires meet or exceed all of the minimum performance requirements of FMVSS No. 139. In addition... performance tires; their asymmetric tread design is one of the main features sought by consumers for the...

78 FR 27476 - Pirelli Tire LLC, Grant of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2013-05-10

... performance and motor vehicle safety because all of the affected tires meet or exceed all of the [[Page 27477... are ultra high performance tires; their asymmetric tread design is one of the main features sought by... these performance characteristics, the customers seek to ensure that their tires are installed correctly...

77 FR 11190 - Yokohama Tire Company, Denial of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2012-02-24

..., endurance and low inflation pressure performance. The tires also meet all of the physical dimension...-0115; Notice 2] Yokohama Tire Company, Denial of Petition for Decision of Inconsequential Noncompliance...: Yokohama Tire Company (YTC),\\1\\ has determined that certain P215/60R15 93H AVID H4S passenger car...

75 FR 51524 - Yokohama Tire Corporation, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2010-08-20

... low inflation pressure performance. The tires also meet all of the physical dimension, resistance to...-0115; Notice 1] Yokohama Tire Corporation, Receipt of Petition for Decision of Inconsequential Noncompliance Yokohama Tire Corporation (YTC) \\1\\ has determined that certain P215/60R15 93H AVID H4S passenger...

Mechanical properties of concrete containing a high volume of tire-rubber particles.

Science.gov (United States)

Khaloo, Ali R; Dehestani, M; Rahmatabadi, P

2008-12-01

Due to the increasingly serious environmental problems presented by waste tires, the feasibility of using elastic and flexible tire-rubber particles as aggregate in concrete is investigated in this study. Tire-rubber particles composed of tire chips, crumb rubber, and a combination of tire chips and crumb rubber, were used to replace mineral aggregates in concrete. These particles were used to replace 12.5%, 25%, 37.5%, and 50% of the total mineral aggregate's volume in concrete. Cylindrical shape concrete specimens 15 cm in diameter and 30 cm in height were fabricated and cured. The fresh rubberized concrete exhibited lower unit weight and acceptable workability compared to plain concrete. The results of a uniaxial compressive strain control test conducted on hardened concrete specimens indicate large reductions in the strength and tangential modulus of elasticity. A significant decrease in the brittle behavior of concrete with increasing rubber content is also demonstrated using nonlinearity indices. The maximum toughness index, indicating the post failure strength of concrete, occurs in concretes with 25% rubber content. Unlike plain concrete, the failure state in rubberized concrete occurs gently and uniformly, and does not cause any separation in the specimen. Crack width and its propagation velocity in rubberized concrete are lower than those of plain concrete. Ultrasonic analysis reveals large reductions in the ultrasonic modulus and high sound absorption for tire-rubber concrete.

Low-temperature gasification of waste tire in a fluidized bed

International Nuclear Information System (INIS)

Xiao Gang; Ni Mingjiang; Chi Yong; Cen Kefa

2008-01-01

In order to recovery energy and materials from waste tire efficiently, low-temperature gasification is proposed. Experiments are carried out in a lab-scale fluidized bed at 400-800 deg. C when equivalence ratio (ER) is 0.2-0.6. Low heat value (LHV) of syngas increases with increasing temperature or decreasing ER, and the yield is in proportion to ER linearly. The yield of carbon black decreases with increasing temperature or ER lightly. When temperature is over 600 deg. C, characteristics of carbon black is similar. When temperature is over 700 deg. C, LHV of syngas rises up lightly with increasing temperature, which indicates that it hardly facilitates gasification any more. It is suitable for tire gasification when temperature is 650-700 deg. C and ER is 0.2-0.4. Under this condition, LHV and yield of syngas are about 4000-9000 kJ/Nm 3 and 1.8-3.7 Nm 3 /kg, respectively; surface area and yield of carbon black lie in range of 20-30 m 3 /g and 550-650 g/kg, respectively. The carbon balance of these experiments achieves 85-95% when temperature is over 600 deg. C

Friction and wear methodologies for design and control

CERN Document Server

Straffelini, Giovanni

2015-01-01

This book introduces the basic concepts of contact mechanics, friction, lubrication, and wear mechanisms, providing simplified analytical relationships that are useful for quantitative assessments. Subsequently, an overview on the main wear processes is provided, and guidelines on the most suitable design solutions for each specific application are outlined. The final part of the text is devoted to a description of the main materials and surface treatments specifically developed for tribological applications and to the presentation of tribological systems of particular engineering relevance. The text is up to date with the latest developments in the field of tribology and provides a theoretical framework to explain friction and wear problems, together with practical tools for their resolution. The text is intended for students on Engineering courses (both bachelor and master degrees) who must develop a sound understanding of friction, wear, lubrication, and surface engineering, and for technicians or professi...

New developments in tire-derived fuels (TDF)

Energy Technology Data Exchange (ETDEWEB)

Gilbert, G. [Kentucky Dept. for Environmental Protection, KY (United States)

2006-07-01

Public opinion on the use of tire derived fuels (TDF) has been influenced by images of the large, uncontrolled tire fires at landfills that fill the atmosphere with heavy black smoke. This presentation discussed some of the issues and challenges related to the introduction of TDF in communities. The United States Environmental Protection Agency currently supports the responsible use of tires in Portland cement kilns and other industrial facilities if they have a storage and handling plan and have secured a permit for all applicable state and federal environmental programs. The use of TDF falls within the EPA resource conservation challenge (RCC) which has initiated a scrap tire workgroup and a TDF committee. The RCC has asked industry using TDF to assemble and share air, water, and product data to assist new TDF users and permitting agencies. TDF is currently used in cement production, by utility boilers, and pulp and paper manufacturers. A recent comparison of TDF and coal characteristics has shown that TDF releases fewer sulphur emissions than coal and produces more energy. While hydrogen emissions are typically higher, nitrogen emissions are lower. An elemental ash analysis has shown that wire-free TDF contains less aluminum than bitumens, as well as less iron. Particulate matter (PM) emissions and volatile organic carbon (VOC) emissions from various plants using TDF are often lower than, or the same as, coal. It was concluded that in order to challenge preconceived notions about TDF, baseline compliance tests should be conducted before presenting data for a permit. Baseline tests should also be conducted with other fuels such as coal within the same timeframe. refs., tabs., figs.

Tire-tread and bitumen particle concentrations in aerosol and soil samples

DEFF Research Database (Denmark)

Fauser, Patrik; Tjell, Jens Christian; Mosbæk, Hans

2002-01-01

% of the mass of airborne particulate tire debris have aerodynamic diameters smaller than 1 mum. The mean aerodynamic diameter is about I gm for the bitumen particles. This size range enables the possibility for far range transport and inhalation by humans. Soil concentrations in the vicinity of a highway...... indicate an approximate exponential decrease with increasing distance from the road. Constant values are reached after about 5 m for the tire particles and 10 m for the bitumen particles. Concentrations in soil that has not been touched for at least 30 years show a decrease in tire concentration...

Study of corrosive-erosive wear behaviour of Al6061/albite composites

International Nuclear Information System (INIS)

Sharma, S.C.; Krishna, M.; Murthy, H.N. Narasimha; Tarachandra, R.; Satyamoorthy, M.; Bhattacharyya, D.

2006-01-01

This investigation analyses the influence of dispersed alumina particles on the wear behaviour of the Al/albite composites in a corrosive environment. The composites were prepared by modified pressure die-casting technique. The corrosive-erosive wear experiments were carried out on a proprietary corrosion-erosion wear tester to study the wear characteristics of the composites. The slurry was made up of water and alumina (size: 90-150 μm, proportion: 0-30 wt.%), while H 2 SO 4 (0.01, 0.1 and 1N) was added to create the corrosive conditions. Experiments were arranged to test the relationships among the corrosive-erosive wear rate, concentrations of H 2 SO 4 and alumina in the slurry, weight percent of albite in the composite, erosion speed and distance. Wear rate varies marginally at low speeds but sharply increases at higher speeds. The corrosive wear rate logarithmically increased with the increasing concentration of the corrosive medium. The effect of abrasive particles and corrosion medium on the wear behaviour of the composite is explained experimentally, theoretically and using scanning electron microscopy

Optimization of an Optical Test Bench for Tire Properties Measurement and Tread Defects Characterization

Directory of Open Access Journals (Sweden)

Juan Jesús Castillo Aguilar

2017-03-01

Full Text Available Tire characteristics and behavior are of great importance in vehicle dynamics since the forces transmitted in the tire-road contact are the main contributors to global vehicle performance. Several research groups have focused on the study and modeling of tires. Some of the most important factors that need to be known are tread characteristics and pressure distribution in the tire-ground contact patch. In this work, a test bench has been used to adequately determine the aforementioned factors. The measurement principle of the test bench is the frustration of total internal reflection (FTIR of light. It makes use of a laterally illuminated glass on which the tire leans. An interposed plastic interface between them causes the reflection of light. Finally, a video camera captures the bright image formed through the glass. The brightness level in each pixel of the image is related to existing normal pressure. A study of the parameters that affect the test bench calibration such as type of interface material used, diffuse light, hysteresis, creep and transverse light absorption is performed. Experimental tests are conducted to relate tire inflation pressure and camber angle to the pressure distribution. Furthermore, the test bench is used to detect and evaluate the influence of defects in the tire on the contact pressures.

Assessment of wheel propeller contact pressure upon soil with use of tire universal performance

Directory of Open Access Journals (Sweden)

Z. A. Godzhaev

2016-01-01

Full Text Available A maximum contact pressure is a key parameter characterizing a level of ecological impact of tractor propellers on the soil. The maximum pressure upon the soil varies with internal pressure in tires and vertical load of a wheel. An universal tire performance can be used at an assessment of change of contact pressure of a wheel propeller upon the soil. The authors offered a technique of definition and regulation of the maximum contact pressure of the wheel propeller upon the basic basis. This technique allows to set parameters for monitoring systems and regulation of the maximum pressure upon the soil by measurement of a tire deflection and change of pressure in tires. At statistical tests for determination of the maximum contact pressure it is necessary to consider the universal performance of the tire nomographically. This nomogram allows to consider visually influence of loading and internal pressure in the tire on a size of the maximum contact pressure. An internal pressure decrease in the tire makes it possible to reduce the maximum pressure upon the soil at constant loading. The authors investigated universal performances of the tires in the range of change of internal air pressure from 160 to 90 kPas. Change of internal pressure from 150 to 100 kPas reduce for the tire 15,5R38 the maximum contact pressure upon 13 kPas (9,6 percent: from 135 to 122 kPas. That corresponds to the admissible level of pressure upon the soil at its humidity in a layer of 0-30 cm: 0,5-0,6 minimum moisture-holding capacity during the spring period and 0,6-0,7 minimum moisture-holding capacity during the autumn period. In case of use of the tire 16,9R38 the maximum pressure upon the soil decreases from 84 to 75 kPas, that is by 10,4 percent.

Influence of the surface treatment of tire rubber residues added in mortars

Directory of Open Access Journals (Sweden)

A. C. Marques

Full Text Available In this work it was evaluated the influence tire rubber addition in mortars in order to replace part of the sand (12% by volume. It was also intended to verify if the tire rubber treatment with NaOH saturated aqueous solution causes interference on the mechanical properties of the mixture. Compressive strength, splitting tensile strength, water absorption, modulus of elasticity, and flow test were made in specimens of 5cmx10cm and the tests were carried out to 7, 28, 56, 90, and 180 days. The results show reduction on mechanical properties values after addition of tire rubber and decrease of the workability. It was also observed that the tire rubber treatment does not cause any alteration on the results compared to the rubber without treatment.

ELEMENTAL ANALYSIS OF RESPIRABLE TIRE PARTICLES AND ASSESSMENT OF CARDIO-PULMONARY TOXICITY IN RATS

Science.gov (United States)

Elemental Analysis of Respirable Tire Particles and Assessment of Cardio-pulmonary Toxicity in RatsR.R. Gottipolu, PhD1, E. Landa, PhD2, J.K. McGee, MS1, M.C. Schladweiler, BS1, J.G. Wallenborn, MS3, A.D. Ledbetter, BS1, J.E. Richards, MS1 and U.P. Kodavanti, PhD1. 1NHEER...

40 CFR 86.1830-01 - Acceptance of vehicles for emission testing.

Science.gov (United States)

2010-07-01

... shall have tires with appropriate tire wear. (b) Special provisions for durability data vehicles. (1... previous model year emission data vehicles, running change vehicles, fuel economy data vehicles, and...

40 CFR 63.4281 - Am I subject to this subpart?

Science.gov (United States)

2010-07-01

..., carpets, high-performance industrial fabrics, luggage, military fabrics, outer wear, sheets, towels, and... tire manufacturing). This would include any web coating line that applies coatings to both tire cord...

49 CFR 571.138 - Standard No. 138; Tire pressure monitoring systems.

Science.gov (United States)

2010-10-01

... following statement in English: Each tire, including the spare (if provided), should be checked monthly when... level to trigger illumination of the TPMS low tire pressure telltale. [The following paragraph is.... If necessary, drive the vehicle until the telltale has extinguished. (o) The test may be repeated...

Stress-based viscoelastic master curve construction of model tire tread compounds

NARCIS (Netherlands)

Maghami, S.; Dierkes, W.; Noordermeer, J.W.M.; Tolpekina, T.; Schultz, S.; Gögelein, C.; Wrana, C.; Gil-Negrete, Nere; Asier, Alonso

2013-01-01

One of the important aspects in the development of new tire compounds is the correlation between the dynamic mechanical properties of the rubber, measured on laboratory scale, and the actual tire performance. In order to predict wet traction, the viscoelastic behavior of the rubber materials at high

41 CFR 101-25.110-3 - Tires accompanying new motor vehicles.

Science.gov (United States)

2010-07-01

... motor vehicles. 101-25.110-3 Section 101-25.110-3 Public Contracts and Property Management Federal...-GENERAL 25.1-General Policies § 101-25.110-3 Tires accompanying new motor vehicles. The tire identifications and recordkeeping regulations issued by the Department of Transportation require each motor...

Effect of Built-Up Edge Formation during Stable State of Wear in AISI 304 Stainless Steel on Machining Performance and Surface Integrity of the Machined Part.

Science.gov (United States)

Ahmed, Yassmin Seid; Fox-Rabinovich, German; Paiva, Jose Mario; Wagg, Terry; Veldhuis, Stephen Clarence

2017-10-25

During machining of stainless steels at low cutting -speeds, workpiece material tends to adhere to the cutting tool at the tool-chip interface, forming built-up edge (BUE). BUE has a great importance in machining processes; it can significantly modify the phenomenon in the cutting zone, directly affecting the workpiece surface integrity, cutting tool forces, and chip formation. The American Iron and Steel Institute (AISI) 304 stainless steel has a high tendency to form an unstable BUE, leading to deterioration of the surface quality. Therefore, it is necessary to understand the nature of the surface integrity induced during machining operations. Although many reports have been published on the effect of tool wear during machining of AISI 304 stainless steel on surface integrity, studies on the influence of the BUE phenomenon in the stable state of wear have not been investigated so far. The main goal of the present work is to investigate the close link between the BUE formation, surface integrity and cutting forces in the stable sate of wear for uncoated cutting tool during the cutting tests of AISI 304 stainless steel. The cutting parameters were chosen to induce BUE formation during machining. X-ray diffraction (XRD) method was used for measuring superficial residual stresses of the machined surface through the stable state of wear in the cutting and feed directions. In addition, surface roughness of the machined surface was investigated using the Alicona microscope and Scanning Electron Microscopy (SEM) was used to reveal the surface distortions created during the cutting process, combined with chip undersurface analyses. The investigated BUE formation during the stable state of wear showed that the BUE can cause a significant improvement in the surface integrity and cutting forces. Moreover, it can be used to compensate for tool wear through changing the tool geometry, leading to the protection of the cutting tool from wear.

Clinical signs of hypoxia with high-Dk soft lens extended wear: is the cornea convinced?

Science.gov (United States)

Sweeney, Deborah F

2003-01-01

To assess the effectiveness of high-Dk soft contact lenses with oxygen transmissibility (Dk/L) beyond the critical level required to avoid corneal edema during overnight wear. The most up-to-date data available on clinical signs of hypoxia with high-Dk contact lenses is reviewed. Chronic corneal edema associated with hypoxia is responsible for the development of large numbers of microcysts, limbal hyperemia, neovascularization, and small increases in myopia. Silicone hydrogel lenses worn continuously for up to 30 nights prevent corneal edema during overnight wear and do not induce a microcyst response. Long-term clinical trials indicate the mean level of limbal redness for patients wearing high-Dk lenses during continuous wear are equivalent to nonlens wearers. No changes in refractive error are associated with continuous wear of high-Dk lenses. High-Dk silicone hydrogel lenses can be worn for up to 3 years with virtual elimination of the hypoxic consequences observed with low-Dk lenses made from conventional lens materials.

78 FR 71032 - Foreign Tire Sales, Inc., Denial of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2013-11-27

...-0063; Notice 2] Foreign Tire Sales, Inc., Denial of Petition for Decision of Inconsequential...). ACTION: Denial of Petition. SUMMARY: Foreign Tire Sales, Inc. (FTS), as importer for ProMeter brand medium truck radial replacement tires manufactured by Shandlong Linglong Rubber Company Limited, has...

A Hybrid Soft Soil Tire Model (HSSTM) For Vehicle Mobility And Deterministic Performance Analysis In Terramechanics Applications

OpenAIRE

Taheri, Shahyar

2015-01-01

Accurate and efficient tire models for deformable terrain operations are essential for performing vehicle simulations. Assessment of the forces and moments that occur at the tire-terrain interface, and the effect of the tire motion on properties of the terrain are crucial in understanding the performance of a vehicle. In order to model the dynamic behavior of the tire on different terrains, a lumped mass discretized tire model using Kelvin-Voigt elements is developed. To optimize the computat...

75 FR 32536 - Foreign Tire Sales, Inc., Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2010-06-08

...-0063; Notice 1] Foreign Tire Sales, Inc., Receipt of Petition for Decision of Inconsequential Noncompliance Foreign Tire Sales, Inc. (FTS) \\1\\, as importer of record for ProMeter brand medium truck radial replacement tires manufactured by Shandlong Linglong Rubber Company Limited has determined that certain...

Wear behavior of niobium carbide coated AISI 52100 steel

International Nuclear Information System (INIS)

Fernandes, Frederico Augusto Pires; Casteletti, Luiz Carlos; Oliveira, Carlos Kleber Nascimento de; Lombardi Neto, Amadeu; Totten, George Edward

2010-01-01

Bearing steels must have high hardness, good wear resistance and dimensional stability. The aim of this work was to study the effect of NbC coating, produced using the thermo-reactive deposition (TRD) process, on the wear resistance of the AISI 52100 steel. Untreated AISI 52100 samples were ground up to 600 mesh emery paper. The bath was composed of 5wt.% ferroniobium (65 wt.% Nb), 3wt.% aluminum and (Na2B4O7) to 100%. Samples were treated at 1000 deg C for 4h and quenched in oil directly from the bath. The resulting layer was characterized by X-ray diffraction, scanning electron microscopy and a micro-abrasive wear testing. The thermo-reactive deposition process in molten borax produced a hard and homogeneous layer composed by NbC, which was confirmed by X-ray diffraction. The NbC coating produced a great increase in the wear resistance of the AISI 52100 steel, decreasing the wear rate by an order of magnitude in relation to the substrate. For coated and uncoated samples the worn volume and wear rate increases with the load. (author)

Dynamic SEM wear studies of tungsten carbide cermets. [friction and wear experiments

Science.gov (United States)

Brainard, W. A.; Buckley, D. H.

1975-01-01

Dynamic friction and wear experiments were conducted in a scanning electron microscope. The wear behavior of pure tungsten carbide and composite with 6 and 15 weight percent cobalt binder was examined, and etching of the binder was done to selectively determine the role of the binder in the wear process. Dynamic experiments were conducted as the tungsten carbide (WC) and bonded WC cermet surfaces were transversed by a 50 micron radiused diamond stylus. These studies show that the predominant wear process in WC is fracture initiated by plastic deformation, and the wear of the etched cermets is similar to pure WC. The presence of the cobalt binder reduces both friction and wear. The cementing action of the cobalt reduces granular separation, and promotes a dense polished layer because of its low shear strength film-forming properties. The wear debris generated from unetched surface is approximately the same composition as the bulk.

Induced spin-accumulation and spin-polarization in a quantum-dot ring by using magnetic quantum dots and Rashba spin-orbit effect

International Nuclear Information System (INIS)

Eslami, L.; Faizabadi, E.

2014-01-01

The effect of magnetic contacts on spin-dependent electron transport and spin-accumulation in a quantum ring, which is threaded by a magnetic flux, is studied. The quantum ring is made up of four quantum dots, where two of them possess magnetic structure and other ones are subjected to the Rashba spin-orbit coupling. The magnetic quantum dots, referred to as magnetic quantum contacts, are connected to two external leads. Two different configurations of magnetic moments of the quantum contacts are considered; the parallel and the anti-parallel ones. When the magnetic moments are parallel, the degeneracy between the transmission coefficients of spin-up and spin-down electrons is lifted and the system can be adjusted to operate as a spin-filter. In addition, the accumulation of spin-up and spin-down electrons in non-magnetic quantum dots are different in the case of parallel magnetic moments. When the intra-dot Coulomb interaction is taken into account, we find that the electron interactions participate in separation between the accumulations of electrons with different spin directions in non-magnetic quantum dots. Furthermore, the spin-accumulation in non-magnetic quantum dots can be tuned in the both parallel and anti-parallel magnetic moments by adjusting the Rashba spin-orbit strength and the magnetic flux. Thus, the quantum ring with magnetic quantum contacts could be utilized to create tunable local magnetic moments which can be used in designing optimized nanodevices.

Investigation of the Effect of Dimple Bionic Nonsmooth Surface on Tire Antihydroplaning.

Science.gov (United States)

Zhou, Haichao; Wang, Guolin; Ding, Yangmin; Yang, Jian; Zhai, Huihui

2015-01-01

Inspired by the idea that bionic nonsmooth surfaces (BNSS) reduce fluid adhesion and resistance, the effect of dimple bionic nonsmooth structure arranged in tire circumferential grooves surface on antihydroplaning performance was investigated by using Computational Fluid Dynamics (CFD). The physical model of the object (model of dimple bionic nonsmooth surface distribution, hydroplaning model) and SST k - ω turbulence model are established for numerical analysis of tire hydroplaning. By virtue of the orthogonal table L16(4(5)), the parameters of dimple bionic nonsmooth structure design compared to the smooth structure were analyzed, and the priority level of the experimental factors as well as the best combination within the scope of the experiment was obtained. The simulation results show that dimple bionic nonsmooth structure can reduce water flow resistance by disturbing the eddy movement in boundary layers. Then, optimal type of dimple bionic nonsmooth structure is arranged on the bottom of tire circumferential grooves for hydroplaning performance analysis. The results show that the dimple bionic nonsmooth structure effectively decreases the tread hydrodynamic pressure when driving on water film and increases the tire hydroplaning velocity, thus improving tire antihydroplaning performance.

Investigation of the Effect of Dimple Bionic Nonsmooth Surface on Tire Antihydroplaning

Directory of Open Access Journals (Sweden)

Haichao Zhou

2015-01-01

Full Text Available Inspired by the idea that bionic nonsmooth surfaces (BNSS reduce fluid adhesion and resistance, the effect of dimple bionic nonsmooth structure arranged in tire circumferential grooves surface on antihydroplaning performance was investigated by using Computational Fluid Dynamics (CFD. The physical model of the object (model of dimple bionic nonsmooth surface distribution, hydroplaning model and SST k-ω turbulence model are established for numerical analysis of tire hydroplaning. By virtue of the orthogonal table L16(45, the parameters of dimple bionic nonsmooth structure design compared to the smooth structure were analyzed, and the priority level of the experimental factors as well as the best combination within the scope of the experiment was obtained. The simulation results show that dimple bionic nonsmooth structure can reduce water flow resistance by disturbing the eddy movement in boundary layers. Then, optimal type of dimple bionic nonsmooth structure is arranged on the bottom of tire circumferential grooves for hydroplaning performance analysis. The results show that the dimple bionic nonsmooth structure effectively decreases the tread hydrodynamic pressure when driving on water film and increases the tire hydroplaning velocity, thus improving tire antihydroplaning performance.

75 FR 73159 - Continental Tire North America, Inc., Receipt of Petition for Decision of Inconsequential...

Science.gov (United States)

2010-11-29

...-0153; Notice 1] Continental Tire North America, Inc., Receipt of Petition for Decision of Inconsequential Noncompliance Continental Tire North America, Inc., (Continental),\\1\\ has determined that certain passenger car replacement tires manufactured in 2009 do not fully comply with paragraph S5.5(b) of Federal...

78 FR 35357 - Bridgestone Americas Tire Operations, LLC, Grant of Petition for Decision of Inconsequential...

Science.gov (United States)

2013-06-12

... safety since the actual performance of the subject tires will not be affected by the mismarking. Bridgestone supports this belief by stating that the tires met the performance requirements of FMVSS No. 139...-0025; Notice 2] Bridgestone Americas Tire Operations, LLC, Grant of Petition for Decision of...

75 FR 81712 - The Goodyear Tire & Rubber Company, Receipt of Petition for Decision of Inconsequential...

Science.gov (United States)

2010-12-28

..., all of the tires included in this petition meet or exceed the performance requirements of FMVSS No...-0174; Notice 1] The Goodyear Tire & Rubber Company, Receipt of Petition for Decision of Inconsequential Noncompliance The Goodyear Tire & Rubber Company (Goodyear) \\1\\ has determined that certain Goodyear commercial...

Assessment of wear facets produced by the ACTA wear machine

DEFF Research Database (Denmark)

Benetti, Ana R; Larsen, Liselotte; Dowling, Adam H

2016-01-01

. The mean wear depth was measured using the traditionally employed 2D and compared with the 3D profilometric (digital) techniques. Data were submitted to analyses of variance, Tukey's post hoc tests and Independent Samples Student's t-tests (where appropriate) at p...OBJECTIVE: To investigate the use of a three-dimensional (3D) digital scanning method in determining the accuracy of the wear performance parameters of resin-based composites (RBCs) determined using a two-dimensional (2D) analogue methodology following in-vitro testing in an Academisch Centrum...... for Tandheelkunde Amsterdam (ACTA) wear machine. METHODS: Specimens compatible with the compartments of the ACTA wear machine specimen wheel (n=10) were prepared from one commercial and four experimental RBCs. The RBC specimens were rotated against an antagonist wheel in a food-like slurry for 220,000 wear cycles...

A comparative study of natural rubber modified with ground tire rubber of truck

OpenAIRE

Binti Haridan, Ili Liyana

2016-01-01

The recycling of waste rubber has considerable significance in term of environmental protection and energy conservation. Considering that most of the relevant literature is concerned with tire recycling, the aim of this work was to develop and characterize the elastomeric samples of natural rubber (NR) composites filled with ground tire rubber of truck (GTR) devulcanized by microwave (DGTR). The tire rubber was ground under ambient conditions and subjected to microwave exposure for 3, 5 and ...

Polymer wear evaluation

DEFF Research Database (Denmark)

Lagerbon, Mikkel; Sivebæk, Ion Marius

2012-01-01

Polymer wear plays an increasing role in manufacturing of machine parts for e.g. medical devices. Some of these have an expected lifetime of five to eight years during which very little wear of the components is acceptable. Too much wear compromises the dosage accuracy of the device and thereby...... the safety of the patients. Prediction of the wear of polymers is complicated by the low thermal conductivity of this kind of material. It implies that any acceleration of testing conditions by increased contact pressure and/or sliding velocity will make the polymer fail due to exaggerated heat buildup....... This is not the kind of wear observed in medical devices. In the present work a method was developed capable of evaluating the wear progression in polymer-polymer contacts. The configuration of the setup is injection moulded specimens consisting of an upper part having a toroid shape and a lower flat part. The sliding...

Effect of thin water film on tire/road friction

OpenAIRE

BEAUTRU, Yannick; KANE, Malal; CEREZO, Véronique; DO, Minh Tan

2011-01-01

Water film on pavement surfaces entails a decrease of friction between the tire and the road. Nevertheless, only effects of water films above 1mm depth were investigated until now, considering hydroplaning risk. From these investigations, formulae were derived to predict the so-called hydroplaning speed at which happen hazardous situations for the driver because there is no more contact between the tire and the road. However, a significant number of accidents occurs on very thin water film su...

Effect of thin water film on tire/road friction

OpenAIRE

BEAUTRU, Yannick

2011-01-01

Water film on pavement surfaces entails a decrease of friction between the tire and the road. Nevertheless,only effects of water films above 1mm depth were investigated until now, considering hydroplaning risk. From these investigations, formulae were derived to predict the so-called hydroplaning speed at which happen hazardous situations for the driver because there is no more contact between the tire and the road. However, a significant number of accidents occurs on very thin water film suc...

40 CFR 63.6006 - How do I demonstrate continuous compliance with the emission limits for tire cord production...

Science.gov (United States)

2010-07-01

... compliance with the emission limits for tire cord production affected sources? 63.6006 Section 63.6006... Hazardous Air Pollutants: Rubber Tire Manufacturing Continuous Compliance Requirements for Tire Cord... tire cord production affected sources? (a) You must demonstrate continuous compliance with each...

Longitudinal tire force estimation based on sliding mode observer

Energy Technology Data Exchange (ETDEWEB)

El Hadri, A.; Cadiou, J.C.; M' Sirdi, N.K. [Versailles Univ., Paris (France). Lab. de Robotique; Beurier, G.; Delanne, Y. [Lab. Central des Ponts, Centre de Nantes (France)

2001-07-01

This paper presents an estimation method for vehicle longitudinal dynamics, particularly the tractive/braking force. The estimation can be used to detect a critical driving situation to improve security. It can be used also in several vehicle control systems. The main characteristics of the vehicle longitudinal dynamics were taken into account in the model used to design an observer and computer simulations. The state variables are the angular wheel velocity, vehicle velocity and the longitudinal tire force. The proposed differential equation of the tractive/braking force is derived using the concept of relaxation length. The observer designed is based on the sliding mode approach using only the angular wheel velocity measurement. The proposed method of estimation is verified through a one-wheel simulation model with a ''Magic formula'' tire model. Simulations results show an excellent reconstruction of the tire force. (orig.)

Adsorption of uranium on adsorbents produced from used tires

International Nuclear Information System (INIS)

Mahramanlioglu, M.

2003-01-01

Potential use of adsorbents produced from used tires for the removal of uranium from aqueous solutions is investigated. Two different adsorbents were used including char and activated carbon produced from used tires. The surface area was larger on activated carbon. Adsorption experiments were carried out as a function of time, adsorbent concentration, pH and initial concentration of uranium. The adsorption kinetics was found to follow the Lagergren equation. The rate constants of intraparticle diffusion and mass transfer coefficients were calculated. It was shown that the equilibrium data could be fitted by the Langmuir and Freundlich equations. The adsorption of uranium in the presence of different cations were also studied and the results were correlated with the ionic potential of the cations. It was demonstrated that the activated carbon produced from used tires can be considered as an adsorbent that has a commercial potential for uranium removal. (author)

77 FR 20482 - Bridgestone Americas Tire Operations, LLC, Receipt of Petition for Decision of Inconsequential...

Science.gov (United States)

2012-04-04

... performance of the subject tires will not be affected by the mismarking. Bridgestone supports this belief by stating that the tires met the performance requirements of FMVSS No. 139 for endurance and high speed when...-0025; Notice 1] Bridgestone Americas Tire Operations, LLC, Receipt of Petition for Decision of...

Tech Transfer Office discusses the finer points of tire recycling

Science.gov (United States)

1995-01-01

NASA's Technology Transfer Office at Stennis worked with a tire recycling company in St. Francisville, La., to help the company make better use of the cryogenics, or supercold fluids, in its recycling process. The process separates the rubber from the steel belts and other particles. The rubber is broken down into a material called crumb. Other parts of the tire particle removed is called fluff.

Outbursts from the secondary component in OJ 287 and the secondary spin-up

Directory of Open Access Journals (Sweden)

Pihajoki P.

2012-12-01

Full Text Available At the end of March 2012 a prominent optical outburst was observed in the binary black hole system OJ 287. It does not fit the expected sequence of outbursts from the primary component and the bremsstrahlung outbursts from the accretion disk impacts of the secondary component. These occur in a well established pattern repeated with an approximately 12 year interval. In this work we discuss the possibility that the outburst originates from the secondary black hole. The timing of the 2012 outburst relative to the expected sequence would make it a counterpart of the precursor outbursts in 1993 and 2004, which occured before the main pattern of outbursts. If so, it appears that a precursor occurs when the secondary reaches a constant level above the mean accretion disk level of the primary component. It may be that this encounter induces an outburst in the secondary which is nearly as prominent as the outbursts in the expected sequence. The strength of these outbursts depends strongly on the spin of the secondary. In this work we investigate the limits on the secondary spin-up and spin alignment from interaction with the accretion disk of the primary component and its magnetic field.

Research of Sustainable Use of Tire Shreds in Landfill

Directory of Open Access Journals (Sweden)

Kristina Bazienė

2016-08-01

Full Text Available Studies are on-going to establish the suitability of tire shreds in the landfill bottom drainage layer, to minimize clogging. Four experimental columns were constructed in which were 500 mm long and 200 mm in diameter. They were filled with different fillers and with a different amount of tire shreds. The most important problem with drainage filler in landfills is clogging. Over long periods of time in landfill operation, the drainage layer clogs (the pores of the layer become smaller and the porosity of the layer becomes smaller. The experiment was carried out for 365 days. Although the landfill for this period represents only one-fiftieth or less of the operation time, the laboratory tests found that the drainage layer bandwidth of reduction in one year can have a negative impact in the long run over time. The main elements that influence the decrease of conductivity are the total suspended solids and calcium and iron compounds. The change of these compounds was observed during the column study, where the concentration of each month in all the columns was decreasing. The results showed that the waste of rubber (tire shreds used for creating fillers in columns provided greater porosity of the layer. It is a beneficial reason to use a rubble and tire shreds waste mix for forming the drainage layer in landfills.

40 CFR 63.5996 - How do I demonstrate initial compliance with the emission limits for tire production affected...

Science.gov (United States)

2010-07-01

... with the emission limits for tire production affected sources? 63.5996 Section 63.5996 Protection of... Pollutants: Rubber Tire Manufacturing Testing and Initial Compliance Requirements for Tire Production Affected Sources § 63.5996 How do I demonstrate initial compliance with the emission limits for tire...

40 CFR 63.6004 - How do I demonstrate continuous compliance with the emission limits for tire production affected...

Science.gov (United States)

2010-07-01

... compliance with the emission limits for tire production affected sources? 63.6004 Section 63.6004 Protection... Pollutants: Rubber Tire Manufacturing Continuous Compliance Requirements for Tire Production Affected Sources § 63.6004 How do I demonstrate continuous compliance with the emission limits for tire production...

Wear analysis of disc cutters of full face rock tunnel boring machine

Science.gov (United States)

Zhang, Zhaohuang; Meng, Liang; Sun, Fei

2014-11-01

Wear is a major factor of disc cutters' failure. No current theory offers a standard for the prediction of disc cutter wear yet. In the field the wear prediction method commonly used is based on the excavation length of tunnel boring machine(TBM) to predict the disc cutter wear and its wear law, considering the location number of each disc cutter on the cutterhead(radius for installation); in theory, there is a prediction method of using arc wear coefficient. However, the preceding two methods have their own errors, with their accuracy being 40% or so and largely relying on the technicians' experience. Therefore, radial wear coefficient, axial wear coefficient and trajectory wear coefficient are defined on the basis of the operating characteristics of TBM. With reference to the installation and characteristics of disc cutters, those coefficients are modified according to penetration, which gives rise to the presentation of comprehensive axial wear coefficient, comprehensive radial wear coefficient and comprehensive trajectory wear coefficient. Calculation and determination of wear coefficients are made with consideration of data from a segment of TBM project(excavation length 173 m). The resulting wear coefficient values, after modification, are adopted to predict the disc cutter wear in the follow-up segment of the TBM project(excavation length of 5621 m). The prediction results show that the disc cutter wear predicted with comprehensive radial wear coefficient and comprehensive trajectory wear coefficient are not only accurate(accuracy 16.12%) but also highly congruous, whereas there is a larger deviation in the prediction with comprehensive axial wear coefficient(accuracy 41%, which is in agreement with the prediction of disc cutters' life in the field). This paper puts forth a new method concerning prediction of life span and wear of TBM disc cutters as well as timing for replacing disc cutters.

IMPROVING THE MODEL OF EMISSION FROM SPINNING DUST: EFFECTS OF GRAIN WOBBLING AND TRANSIENT SPIN-UP

International Nuclear Information System (INIS)

Hoang, Thiem; Lazarian, A.; Draine, B. T.

2010-01-01

Observations continue to support the interpretation of the anomalous microwave foreground as electric dipole radiation from spinning dust grains as proposed by Draine and Lazarian. In this paper, we present a refinement of the original model by improving the treatment of a number of physical effects. First, we consider a disk-like grain rotating with angular velocity at an arbitrary angle with respect to the grain symmetry axis (i.e., grain wobbling) and derive the rotational damping and excitation coefficients arising from infrared emission, plasma-grain interactions, and electric dipole emission. The angular velocity distribution and the electric dipole emission spectrum for disk-like grains is calculated using the Langevin equation, for cases both with and without fast internal relaxation. Our results show that for fast internal relaxation, the peak emissivity of spinning dust, compared to earlier studies, increases by a factor of ∼2 for the warm neutral medium (WNM), the warm ionized medium (WIM), the cold neutral medium (CNM), and the photodissociation region, and by a factor ∼4 for reflection nebulae. The frequency at the emission peak also increases by factors ∼1.4 to ∼2 for these media. Without internal relaxation, the increase of emissivity is comparable, but the emission spectrum is more extended to higher frequency. The increased emission results from the non-sphericity of grain shape and from the anisotropy in damping and excitation along directions parallel and perpendicular to the grain symmetry axis. Second, we provide a detailed numerical study including transient spin-up of grains by single-ion collisions. The range of grain size in which single-ion collisions are important is identified. The impulses broaden the emission spectrum and increase the peak emissivity for the CNM, WNM, and WIM, although the increases are not as large as those due to the grain wobbling. In addition, we present an improved treatment of rotational excitation and

Advanced Wear-resistant Nanocomposites for Increased Energy Efficiency

Energy Technology Data Exchange (ETDEWEB)

Cook, B. A.; Harringa, J. L.; Russel, A. M.

2012-12-01

This report summarizes the work performed by an Ames-led project team under a 4-year DOE-ITP sponsored project titled, 'Advanced Wear-resistant Nanocomposites for Increased Energy Efficiency.' The Report serves as the project deliverable for the CPS agreement number 15015. The purpose of this project was to develop and commercialize a family of lightweight, bulk composite materials that are highly resistant to degradation by erosive and abrasive wear. These materials, based on AlMgB{sub 14}, are projected to save over 30 TBtu of energy per year when fully implemented in industrial applications, with the associated environmental benefits of eliminating the burning of 1.5 M tons/yr of coal and averting the release of 4.2 M tons/yr of CO{sub 2} into the air. This program targeted applications in the mining, drilling, machining, and dry erosion applications as key platforms for initial commercialization, which includes some of the most severe wear conditions in industry. Production-scale manufacturing of this technology has begun through a start-up company, NewTech Ceramics (NTC). This project included providing technical support to NTC in order to facilitate cost-effective mass production of the wear-resistant boride components. Resolution of issues related to processing scale-up, reduction in energy intensity during processing, and improving the quality and performance of the composites, without adding to the cost of processing were among the primary technical focus areas of this program. Compositional refinements were also investigated in order to achieve the maximum wear resistance. In addition, synthesis of large-scale, single-phase AlMgB{sub 14} powder was conducted for use as PVD sputtering targets for nanocoating applications.

77 FR 71678 - The Goodyear Tire & Rubber Company, Receipt of Petition for Decision of Inconsequential...

Science.gov (United States)

2012-12-03

...: The Goodyear Tire & Rubber Company (GOODYEAR),\\1\\ has determined that certain Goodyear brand tires... LT 275/65R18 brand tires manufactured between April 8, 2012, and May 12, 2012 at its plant in Gadsden.... Electronically: By logging onto the Federal Docket Management System (FDMS) Web site at http://www.regulations...

Experiments on Spray from a Rolling Tire

Science.gov (United States)

Radovich, Charles; Browand, Fred

2010-11-01

A novel laboratory apparatus has been built to understand the mechanisms and statistics of droplet production for spray emerging from a rolling tire. Using high-speed imaging, water passing through a single circumferential groove was observed to leave the tire contact patch in the form of a liquid sheet of non-uniform thickness. The sheet breaks into droplets as a result of several, organized instabilities. Measurements for the breakup length of the liquid sheet showed a dependence on Weber number proportional to We-1/6, for Weber numbers of 2700, 10900 and 24400. A technique to identify and size water droplets was developed and the distribution of droplet sizes was determined as a function of Weber number. At We = 2700, droplet sizes between 80 and 9000μm were detected, with a mean diameter near 800μm. Both the range of droplet sizes and the mean diameter were found to decrease with increasing Weber number as (approximately) We-1/2. Correlation Image Velocimetry (CIV) was used to estimate the distribution of droplet velocities as a function of droplet size. The spread of droplet velocities about the tire peripheral speed is strongly correlated with droplet size. The spread can be estimated by a simple physical model incorporating rigid droplets subject to gravity and drag.

Numerical Study of Tire Hydroplaning Based on Power Spectrum of Asphalt Pavement and Kinetic Friction Coefficient

OpenAIRE

Shengze Zhu; Xiuyu Liu; Qingqing Cao; Xiaoming Huang

2017-01-01

Hydroplaning is a driving phenomenon threating vehicle’s control stability and safety. It happens when tire rolls on wet pavement with high speed that hydrodynamic force uplifts the tire. Accurate numerical simulation to reveal the mechanism of hydroplaning and evaluate the function of relevant factors in this process is significant. In order to describe the friction behaviors of tire-pavement interaction, kinetic friction coefficient curve of tire rubber and asphalt pavement was obtained by ...

Calculation of wear (f.i. wear modulus) in the plastic cup of a hip joint prosthesis

NARCIS (Netherlands)

Ligterink, D.J.

1975-01-01

The wear equation is applied to the wear process in a hip joint prosthesis and a wear modulus is defined. The sliding distance, wear modulus, wear volume, wear area, contact angle and the maximum normal stress were calculated and the theoretical calculations applied to test results. During the wear

Tire inspection system with shielded x-ray source

International Nuclear Information System (INIS)

Heisner, D.N.; Palermo, A. Jr.; Loyer, P.K.

1976-01-01

An automated tire inspection system is described which employs a penetrative radiation, such as x-radiation, to inspect the integrity of portions of tires fed sequentially along a feed path through a centering station and into a shielded enclosure where an inspection station is defined. Features of the system include a continuously operating x-ray source movable between inspection and retracted positions, and an x-ray shield for covering the source when it is retracted to permit the doors of the shielded enclosure to be opened without danger from escaping radiation. 19 Claims, 38 Drawing Figures

DURABILITY OF GREEN CONCRETE WITH TERNARY CEMENTITIOUS SYSTEM CONTAINING RECYCLED AGGREGATE CONCRETE AND TIRE RUBBER WASTES

Directory of Open Access Journals (Sweden)

MAJID MATOUQ ASSAS

2016-06-01

Full Text Available All over the world billions of tires are being discarded and buried representing a serious ecological threat. Up to now a small part is recycled and millions of tires are just stockpiled, landfilled or buried. This paper presents results about the properties and the durability of green concrete contains recycled concrete as a coarse aggregate with partial replacement of sand by tire rubber wastes for pavement use. Ternary cementious system, Silica fume, Fly ash and Cement Kiln Dust are used as partial replacement of cement by weight. Each one replaced 10% of cement weight to give a total replacement of 30%. The durability performance was assessed by means of water absorption, chloride ion permeability at 28 and 90 days, and resistance to sulphuric acid attack at 1, 7, 14 and 28 days. Also to the compression behaviors for the tested specimens at 7, 14, 28 and 90 days were detected. The results show the existence of ternary cementitious system, silica fly ash and Cement Kiln Dust minimizes the strength loss associated to the use of rubber waste. In this way, up to 10% rubber content and 30% ternary cementious system an adequate strength class value (30 MPa, as required for a wide range of common structural uses, can be reached both through natural aggregate concrete and recycled aggregate concrete. Results also show that, it is possible to use rubber waste up to 15% and still maintain a high resistance to acid attack. The mixes with 10%silica fume, 10% fly ash and 10% Cement Kiln Dust show a higher resistance to sulphuric acid attack than the reference mix independently of the rubber waste content. The mixes with rubber waste and ternary cementious system was a lower resistance to sulphuric acid attack than the reference mix.

40 CFR 63.5985 - What are my alternatives for meeting the emission limits for tire production affected sources?

Science.gov (United States)

2010-07-01

... the emission limits for tire production affected sources? 63.5985 Section 63.5985 Protection of... Pollutants: Rubber Tire Manufacturing Emission Limits for Tire Production Affected Sources § 63.5985 What are my alternatives for meeting the emission limits for tire production affected sources? You must use...

40 CFR 63.5999 - How do I demonstrate initial compliance with the emission limits for tire cord production...

Science.gov (United States)

2010-07-01

... with the emission limits for tire cord production affected sources? 63.5999 Section 63.5999 Protection... Pollutants: Rubber Tire Manufacturing Testing and Initial Compliance Requirements for Tire Cord Production Affected Sources § 63.5999 How do I demonstrate initial compliance with the emission limits for tire cord...

A mechanistic understanding of the wear coefficient: From single to multiple asperities contact

Science.gov (United States)

Frérot, Lucas; Aghababaei, Ramin; Molinari, Jean-François

2018-05-01

Sliding contact between solids leads to material detaching from their surfaces in the form of debris particles, a process known as wear. According to the well-known Archard wear model, the wear volume (i.e. the volume of detached particles) is proportional to the load and the sliding distance, while being inversely proportional to the hardness. The influence of other parameters are empirically merged into a factor, referred to as wear coefficient, which does not stem from any theoretical development, thus limiting the predictive capacity of the model. Based on a recent understanding of a critical length-scale controlling wear particle formation, we present two novel derivations of the wear coefficient: one based on Archard's interpretation of the wear coefficient as the probability of wear particle detachment and one that follows naturally from the up-scaling of asperity-level physics into a generic multi-asperity wear model. As a result, the variation of wear rate and wear coefficient are discussed in terms of the properties of the interface, surface roughness parameters and applied load for various rough contact situations. Both new wear interpretations are evaluated analytically and numerically, and recover some key features of wear observed in experiments. This work shines new light on the understanding of wear, potentially opening a pathway for calculating the wear coefficient from first principles.

Accuracy and precision of estimating age of gray wolves by tooth wear

Science.gov (United States)

Gipson, P.S.; Ballard, W.B.; Nowak, R.M.; Mech, L.D.

2000-01-01

We evaluated the accuracy and precision of tooth wear for aging gray wolves (Canis lupus) from Alaska, Minnesota, and Ontario based on 47 known-age or known-minimum-age skulls. Estimates of age using tooth wear and a commercial cementum annuli-aging service were useful for wolves up to 14 years old. The precision of estimates from cementum annuli was greater than estimates from tooth wear, but tooth wear estimates are more applicable in the field. We tended to overestimate age by 1-2 years and occasionally by 3 or 4 years. The commercial service aged young wolves with cementum annuli to within ?? 1 year of actual age, but under estimated ages of wolves ???9 years old by 1-3 years. No differences were detected in tooth wear patterns for wild wolves from Alaska, Minnesota, and Ontario, nor between captive and wild wolves. Tooth wear was not appropriate for aging wolves with an underbite that prevented normal wear or severely broken and missing teeth.

Numerical study on physical mechanism of vortex breakdown occurrence in spin-up process

OpenAIRE

"小出, 輝明"; Teruaki", "Koide

2008-01-01

"A Numerical study presented on a vortex breakdown in spin-up process in an enclosed cylindrical container. In a transitional state, momentary vortex breakdowns can occur for particular parameter values ofthe Reynolds number and aspect ratio where no vortex breakdown appears in a steady state. This transient vortex breakdown flow is convenient to consider a mechanism for the occurrence of a vortex breakdown. It isdiscussed that periodical increase and decrease of angular momentum in upstream ...

Adsorption of Pb(II by Activated Pyrolytic Char from Used Tire

Directory of Open Access Journals (Sweden)

Lu Ping

2016-01-01

Full Text Available As a renewable resource, the pyrolytic char derived from used tire has promising adsorption capacities owing to its similar structure and properties with active carbon. The purification and activation of the pyrolytic char from used tire, as well as the application of this material in the adsorption of Pb(II in water is conducted. The influences on the adsorption capacity by temperature and pH value are investigated and discussed; the adsorption thermodynamics and kinetics are also studied. The results show that the pyrolytic char from used tire has remarkable adsorption capacity for Pb(II, and the adsorption is an endothermic process complying with the Langmuir isotherm. The adsorption kinetics is a pseudo second-order reaction.

Streaks to rings to vortex grids: generic patterns in transient convective spin up of an evaporating fluid.

Science.gov (United States)

Zhong, J-Q; Patterson, M D; Wettlaufer, J S

2010-07-23

We observe the transient formation of a ringed pattern state during spin up of an evaporating fluid on a time scale of order a few Ekman spin up times. The ringed state is probed using infrared thermometry and particle image velocimetry and it is demonstrated to be a consequence of the transient balance between Coriolis and viscous forces which dominate inertia, each of which are extracted from the measured velocity field. The breakdown of the ringed state is quantified in terms of the antiphasing of these force components which drives a Kelvin-Helmholtz instability and we show that the resulting vortex grid spacing scales with the ring wavelength. This is the fundamental route to quasi-two-dimensional turbulent vortex flow and thus may have implications in astrophysics and geophysics wherein rotating convection is ubiquitous.

Tire-rim interface pressure of a commercial vehicle wheel under radial loads: theory and experiment

Science.gov (United States)

Wan, Xiaofei; Shan, Yingchun; Liu, Xiandong; He, Tian; Wang, Jiegong

2017-11-01

The simulation of the radial fatigue test of a wheel has been a necessary tool to improve the design of the wheel and calculate its fatigue life. The simulation model, including the strong nonlinearity of the tire structure and material, may produce accurate results, but often leads to a divergence in calculation. Thus, a simplified simulation model in which the complicated tire model is replaced with a tire-wheel contact pressure model is used extensively in the industry. In this paper, a simplified tire-rim interface pressure model of a wheel under a radial load is established, and the pressure of the wheel under different radial loads is tested. The tire-rim contact behavior affected by the radial load is studied and analyzed according to the test result, and the tire-rim interface pressure extracted from the test result is used to evaluate the simplified pressure model and the traditional cosine function model. The results show that the proposed model may provide a more accurate prediction of the wheel radial fatigue life than the traditional cosine function model.

Tool Wear Analysis due to Machining In Super Austenitic Stainless Steel

Directory of Open Access Journals (Sweden)

Polishetty Ashwin

2017-01-01

Full Text Available This paper presents tool wear study when a machinability test was applied using milling on Super Austenitic Stainless Steel AL6XN alloy. Eight milling trials were performed under two cutting speeds, 100 m/min and 150 m/min, combined with two feed rates at 0.1mm/tooth and 0.15 mm/tooth and two depth of cuts at 2 mm and 3 mm. An Alicona 3D optical surface profilometer was used to scan cutting inserts flank and rake face areas for wear. Readings such as maximum and minimum deviations were extracted and used to analyse the outcomes. Results showed various types of wear were generated on the tool rake and flank faces. The common formed wear was the crater wear. The formation of the build-up edge was observed on the rake face of the cutting tool.

Wear resistance of polypropylene-SiC composite

Science.gov (United States)

Abenojar, J.; Enciso, B.; Martínez, MA; Velasco, F.

2017-05-01

In this work, the wear resistance of thermoplastic composites with a high amount of ceramic is evaluated. Composites made of polypropylene (PP) and silicon carbide (SiC) powder at 50 wt% were used with the final objective of manufacturing ablative materials. This is the first part of a project studying the wear resistance and the mechanical properties of those composites, to be used in applications like habitat industry. In theory, the exposure to high temperature of ablative materials involves the elimination of thermal energy by the sacrifice of surface polymer. In our case, PP will act as a heat sink, up to the reaction temperature (melting or sublimation), where endothermic chemical decomposition into charred material and gaseous products occurs. As the surface is eroded, it is formed a SiC like-foam with improved insulation performance. Composites were produced by extrusion and hot compression. The wear characterization was performed by pin-on-disk test. Wear test was carried out under standard ASTM G99. The parameters were 120 rpm speed, 15 N load, a alumina ball with 6 mm as pin and 1000 m sliding distance. The tracks were also observed by opto-digital microscope.

Wear resistance of polypropylene-SiC composite

International Nuclear Information System (INIS)

Abenojar, J; Enciso, B; Martínez, MA; Velasco, F

2017-01-01

In this work, the wear resistance of thermoplastic composites with a high amount of ceramic is evaluated. Composites made of polypropylene (PP) and silicon carbide (SiC) powder at 50 wt% were used with the final objective of manufacturing ablative materials. This is the first part of a project studying the wear resistance and the mechanical properties of those composites, to be used in applications like habitat industry. In theory, the exposure to high temperature of ablative materials involves the elimination of thermal energy by the sacrifice of surface polymer. In our case, PP will act as a heat sink, up to the reaction temperature (melting or sublimation), where endothermic chemical decomposition into charred material and gaseous products occurs. As the surface is eroded, it is formed a SiC like-foam with improved insulation performance. Composites were produced by extrusion and hot compression. The wear characterization was performed by pin-on-disk test. Wear test was carried out under standard ASTM G99. The parameters were 120 rpm speed, 15 N load, a alumina ball with 6 mm as pin and 1000 m sliding distance. The tracks were also observed by opto-digital microscope. (paper)

76 FR 15045 - Goodyear Tire and Rubber Company, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2011-03-18

...-0033; Notice 1] Goodyear Tire and Rubber Company, Receipt of Petition for Decision of Inconsequential Noncompliance Goodyear Tire and Rubber Company, (Goodyear),\\1\\ has determined that approximately 26,224 Goodyear Assurance ComforTred Touring passenger replacement car tires manufactured between January 4, 2010 and...

The accretion powered spin-up of GRO J1750-27

DEFF Research Database (Denmark)

Shaw, S.E.; Hill, A.B.; Kuulkers, E.

2009-01-01

The timing properties of the 4.45 s pulsar in the Be X-ray binary system GRO J1750-27 are examined using hard X-ray data from INTEGRAL and Swift during a type II outburst observed during 2008. The orbital parameters of the system are measured and agree well with those found during the last known...... outburst of the system in 1995. Correcting the effects of the Doppler shifting of the period, due to the orbital motion of the pulsar, leads to the detection of an intrinsic spin-up that is well described by a simple model including. P and P terms of - 7.5 x 10(-10) s s(-1) and 1 x 10(-16) s s(-2...

Vehicle Dynamics Control of In-wheel Electric Motor Drive Vehicles Based on Averaging of Tire Force Usage

Science.gov (United States)

Masaki, Nobuo; Iwano, Haruo; Kamada, Takayoshi; Nagai, Masao

For in-wheel electric motor drive vehicles, a new vehicle dynamics control which is based on the tire force usage rate is proposed. The new controller adopts non-linear optimal control could manage the interference between direct yaw-moment control and the tire force usage rate. The new control is considered total longitudinal and transverse tire force. Therefore the controller can prevent tire force saturation near tire force limit during cornering. Simulations and test runs by the custom made four wheel drive in-wheel motor electric vehicle show that higher driving stability performance compared to the performance of the same vehicle without control.

Structure-property effects on mechanical, friction and wear properties of electron modified PTFE filled EPDM composite

Directory of Open Access Journals (Sweden)

2009-01-01

Full Text Available Tribological properties of Ethylene-Propylene-Diene-rubber (EPDM containing electron modified Polytetrafluoroethylene (PTFE have been investiagted with the help of pin on disk tribometer without lubrication for a testing time of 2 hrs in atmospheric conditions at a sliding speed and applied normal load of 0.05 m•s–1 and FN = 1 N, respectively. Radiation-induced chemical changes in electron modified PTFE powders were analyzed using Electron Spin Resonance (ESR and Fourier Transform Infrared (FTIR specroscopy to characterize the effects of compatibility and chemical coupling of modified PTFE powders with EPDM on mechanical, friction and wear properties. The composites showed different friction and wear behaviour due to unique morphology, dispersion behaviour and radiation functionalization of PTFE powders. In general, EPDM reinforced with electron modified PTFE powder demonstrated improvement both in mechanical and tribological properties. However, the enhanced compatibility of PTFE powder resulting from the specific chemical coupling of PTFE powder with EPDM has been found crucial for mechanical, friction and wear properties.

Tribopolymerization as an anti-wear mechanism. Quarterly progress report

Energy Technology Data Exchange (ETDEWEB)

Furey, M.J.

1996-04-01

The primary objective of this activity is to obtain the necessary data which would enhance, promote, and encourage the introduction of advanced lubrication technology into the marketplace. This includes (a) defining specific but different applications, (b) establishing the limits or ranges of applied loads, speeds, and temperatures over which the concept of tribopolymerization would work in reducing wear and/or friction, (c) continuing in efforts to understand the film-forming process (this rates to (b) above), using this knowledge to develop new and even more effective additives, and (d) exploring possible connections with private and investment companies for the licensing and marketing of products which will reduce friction and wear in a variety of applications. Progress was made in several different but connected areas. These included (a) establishing of load/velocity limits of selected monomers for ceramic lubrication, (b) the discovery of new and effective monomers designed for higher temperature anti-wear applications, (c) improvements and modifications of the high load/high speed pin-on-disk machine, (d) the initiation of related or spin-off projects designed to get their advanced technology into the marketplace, (e) the filing of three new patent applications, and (f) collaborative research with Dr. Kajdas--the co-inventor with Dr. Furey--on tribopolymerization as a novel and effective approach to the boundary lubrication of ceramics and steel. These and other elements of progress made during the first Quarter of 1996 are discussed briefly.

Spin and tunneling dynamics in an asymmetrical double quantum dot with spin-orbit coupling: Selective spin transport device

Science.gov (United States)

Singh, Madhav K.; Jha, Pradeep K.; Bhattacherjee, Aranya B.

2017-09-01

In this article, we study the spin and tunneling dynamics as a function of magnetic field in a one-dimensional GaAs double quantum dot with both the Dresselhaus and Rashba spin-orbit coupling. In particular, we consider different spatial widths for the spin-up and spin-down electronic states. We find that the spin dynamics is a superposition of slow as well as fast Rabi oscillations. It is found that the Rashba interaction strength as well as the external magnetic field strongly modifies the slow Rabi oscillations which is particularly useful for implementing solid state selective spin transport device.

75 FR 36472 - Goodyear Tire and Rubber Company, Receipt of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2010-06-25

...-0080; Notice 1] Goodyear Tire and Rubber Company, Receipt of Petition for Decision of Inconsequential Noncompliance Goodyear Tire and Rubber Company, (Goodyear),\\1\\ has determined that approximately 14,826 passenger car tires manufactured between August of 2007 and May of 2009, do not fully comply with paragraph...

Abrasive wear of intermetallics

International Nuclear Information System (INIS)

Hawk, J.A.; Alman, D.E.; Wilson, R.D.

1995-01-01

The US Bureau of Mines is investigating the wear behavior of a variety of advanced materials. Among the many materials under evaluation are intermetallic alloys based on the compounds: Fe 3 Al, Ti 3 Al, TiAl, Al 3 Ti, NiAl and MoSi 2 . The high hardness, high modulus, low density, and superior environmental stability of these compounds make them attractive for wear materials. This paper reports on the abrasive wear of alloys and composites based on the above compounds. The abrasive wear behavior of these alloys and composites are compared to other engineering materials used in wear applications

49 CFR 571.119 - Standard No. 119; New pneumatic tires for motor vehicles with a GVWR of more than 4,536 kilograms...

Science.gov (United States)

2010-10-01

... without interruption. (e) Immediately after running the tire the required time, measure the tire inflation...) Immediately after running the tire the required time, measure the tire inflation pressure. Remove the tire... 49 Transportation 6 2010-10-01 2010-10-01 false Standard No. 119; New pneumatic tires for motor...

41 CFR 101-25.110-2 - Tires obtained through Federal Supply Schedules or regional term contracts.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Tires obtained through Federal Supply Schedules or regional term contracts. 101-25.110-2 Section 101-25.110-2 Public Contracts... Federal Supply Schedules or regional term contracts. When tire manufacturers ship tires direct against...

Microtomography of elastomers for tire manufacture

Science.gov (United States)

Dunsmuir, John H.; Dias, A. J.; Peiffer, D. G.; Kolb, R.; Jones, G.

1999-09-01

X-ray microtomography is used to image the internal structure of carbon black filled isobutylene-p-methylstyrene-p- bromomethylstyrene (PIB-PMS/BrPMS or ExxProTM) curing bladders before and after use-to-failure in the manufacture of automobile tires. Curing bladders operate under extreme conditions with extended mechanical cycling at high temperatures. Manufacturers typically do not run the bladders until failure but rather a pull policy is established which emphasizes the distribution of cyclic lifetimes. We examine the bladder elastomer structure at a resolution of about 10 microns with the objective of reducing the variability in performance. Using both edge crossing and absorption contrast we identify several types of heterogeneity including voids, foreign inclusions, and the distribution of curative agent from which we infer the uniformity of the cure. The results indicate several potential failure mechanisms. The small number of voids and foreign inclusions are mechanical defects that can initiate cracking. More widespread through the polymer matrix are small regions of polymer devoid of curative agent as shown by absorption edge imaging. These regions may be uncured polymer with poor mechanical and thermal properties that may lead to early failure. After several cure cycles the uncured regions are no longer present in the bladder tread area but they remain near the bead. At high cycles an approximately 500 micrometer thick zinc rich cap develops where the bladder contacts the inner tread area of the tire. This zinc rich cap may cause over-curing of the polymer resulting in crack initiation at the surface of the bladder that contacts the tire.

Extended wearing trial of Trifield lens device for 'tunnel vision'.

Science.gov (United States)

Woods, Russell L; Giorgi, Robert G; Berson, Eliot L; Peli, Eli

2010-05-01

Severe visual field constriction (tunnel vision) impairs the ability to navigate and walk safely. We evaluated Trifield glasses as a mobility rehabilitation device for tunnel vision in an extended wearing trial. Twelve patients with tunnel vision (5-22 degrees wide) due to retinitis pigmentosa or choroideremia participated in the 5-visit wearing trial. To expand the horizontal visual field, one spectacle lens was fitted with two apex-to-apex prisms that vertically bisected the pupil on primary gaze. This provides visual field expansion at the expense of visual confusion (two objects with the same visual direction). Patients were asked to wear these spectacles as much as possible for the duration of the wearing trial (median 8, range 6-60 weeks). Clinical success (continued wear, indicating perceived overall benefit), visual field expansion, perceived direction and perceived visual ability were measured. Of 12 patients, nine chose to continue wearing the Trifield glasses at the end of the wearing trial. Of those nine patients, at long-term follow-up (35-78 weeks), three reported still wearing the Trifield glasses. Visual field expansion (median 18, range 9-38 degrees) was demonstrated for all patients. No patient demonstrated adaptation to the change in visual direction produced by the Trifield glasses (prisms). For reported difficulty with obstacles, some differences between successful and non-successful wearers were found. Trifield glasses provided reported benefits in obstacle avoidance to 7 of the 12 patients completing the wearing trial. Crowded environments were particularly difficult for most wearers. Possible reasons for long-term discontinuation and lack of adaptation to perceived direction are discussed.

Analysis on nondestructive temperature distribution of tire tread part in a running using infrared thermal vision camera

International Nuclear Information System (INIS)

Kim, Jae Yeol; Yang, Dong Jo; Ma, Sang Dong; Park, Byoung Gu; Lee, Ju Wan

2001-01-01

The experimental method which investigates validity of numerical simulation for wheeling tires has not developed until now. Separation of belt caused by sudden temperature increase is the most serious problem with wheeling tires. Actually, separation of belt is closely related with the life cycle and design of tires. It is important to investigate the temperature history of tires because sudden temperature increase on belt accelerates the thermal fatigue and then causes the destruction of bending area in the radial direction. Therefore, in the present study, finite element method (FEM) was used to obtain the accurate temperature distribution of tire. Its results were compared with experimental data acquired by infrared thermal camera.

The effects of studded tires on fatal crashes with passenger cars and the benefits of electronic stability control (ESC) in Swedish winter driving.

Science.gov (United States)

Strandroth, Johan; Rizzi, Matteo; Olai, Maria; Lie, Anders; Tingvall, Claes

2012-03-01

crashes since this technology mostly addresses over-steering. This is also supported by the fact that the share of LOC fatal crashes is considerably lower for ESC-equipped cars. This study recommends that non-ESC cars should be fitted with studded tires if they are to be driven on roads covered by ice or snow. If the proportion of studded tires is to be decreased on Swedish roads to reduce the about of hazardous particulates especially in built up areas, from a road safety point of view it is recommended that this should be done in phase with the implementation of ESC on all passenger cars. Copyright © 2011 Elsevier Ltd. All rights reserved.

Microstructure and wear behaviors of laser clad NiCr/Cr3C2-WS2 high temperature self-lubricating wear-resistant composite coating

Science.gov (United States)

Yang, Mao-Sheng; Liu, Xiu-Bo; Fan, Ji-Wei; He, Xiang-Ming; Shi, Shi-Hong; Fu, Ge-Yan; Wang, Ming-Di; Chen, Shu-Fa

2012-02-01

The high temperature self-lubricating wear-resistant NiCr/Cr3C2-30%WS2 coating and wear-resistant NiCr/Cr3C2 coating were fabricated on 0Cr18Ni9 austenitic stainless steel by laser cladding. Phase constitutions and microstructures were investigated, and the tribological properties were evaluated using a ball-on-disc wear tester under dry sliding condition at room-temperature (17 °C), 300 °C and 600 °C, respectively. Results indicated that the laser clad NiCr/Cr3C2 coating consisted of Cr7C3 primary phase and γ-(Fe,Ni)/Cr7C3 eutectic colony, while the coating added with WS2 was mainly composed of Cr7C3 and (Cr,W)C carbides, with the lubricating WS2 and CrS sulfides as the minor phases. The wear tests showed that the friction coefficients of two coatings both decrease with the increasing temperature, while the both wear rates increase. The friction coefficient of laser clad NiCr/Cr3C2-30%WS2 is lower than the coating without WS2 whatever at room-temperature, 300 °C, 600 °C, but its wear rate is only lower at 300 °C. It is considered that the laser clad NiCr/Cr3C2-30%WS2 composite coating has good combination of anti-wear and friction-reducing capabilities at room-temperature up to 300 °C.

Analysis of mechanism of carbide tool wear and control by wear process

Directory of Open Access Journals (Sweden)

Pham Hoang Trung

2017-01-01

Full Text Available The analysis of physic-mechanical and thermal physic properties of hard alloys depending on their chemical composition is conducted. The correlation of cutting properties and regularities of carbide tool wear with cutting conditions and thermal physic properties of tool material are disclosed. Significant influence on the tool wear of not only mechanical, but, in the first place, thermal physic properties of tool and structural materials is established by the researches of Russian scientists, because in the range of industrial used cutting speeds the cause of tool wear are diffusion processes. The directions of intensity decreasing of tool wear by determining rational processing conditions, the choice of tool materials and wear-resistant coating on tool surface are defined.

Influence of nitrogen ion implantation on wear studied by a new laboratory wear test

Energy Technology Data Exchange (ETDEWEB)

Szilagyi, E.; Paszti, F.; Vertessy, Z. (Central Research Inst. for Physics, Hungarian Academy of Sciences, Budapest (Hungary))

1991-05-01

A new laboratory wear test is developed in which the wear trace is measured by Rutherford backscattering spectrometry. The advantage of the new test is that the wear rate is directly determinable. The new test setup has been used to study the effects of nitrogen implantation on the wear processes on 115CrV3 steel. The wear rate decreases by a factor of 2 at 4x10{sup 17} N{sup +}/cm{sup 2} implanted dose. (orig.).

Delamination wear mechanism in gray cast irons

International Nuclear Information System (INIS)

Salehi, M.

2000-01-01

An investigation of the friction and sliding wear of gray cast iron against chromium plated cast irons was carried out on a newly constructed reciprocating friction and wear tester. The tests were the first to be done on the test rig under dry conditions and at the speed of 170 cm/min, and variable loads of 20-260 N for a duration of 15 min. to 3 hours. The gray cast iron surfaces worn by a process of plastic deformation at the subsurface, crack nucleation, and crack growth leading to formation of plate like debris and therefore the delamination theory applies. No evidence of adhesion was observed. This could be due to formation of oxides on the wear surface which prevent adhesion. channel type chromium plating ''picked'' up cast iron from the counter-body surfaces by mechanically trapping cast iron debris on and within the cracks. The removal of the plated chromium left a pitted surface on the cast iron

Management of used tires, accomplishments in the world, and situation in Serbia

OpenAIRE

Stanojević Dušan D.; Rajković Miloš B.; Tošković Dragan V.

2011-01-01

It is estimated that all over the world there are more than 550 million road vehicles in everyday use. Annually, 1.3 billion used tyres are dismantled from these vehicles due to safety reasons. A small number of these tyres end up reused as second-hand tyres or, after being retreated, as new ones. The rest are end of life tyres which are recycled or used as tire derived fuels under controlled combustion conditions. Modern vehicle tyres are a high-technological product containing, on the...

Friction and wear behavior of laser cladding Ni/hBN self-lubricating composite coating

International Nuclear Information System (INIS)

Zhang Shitang; Zhou Jiansong; Guo Baogang; Zhou Huidi; Pu Yuping; Chen Jianmin

2008-01-01

Ni/hBN coating was successfully prepared on 1Cr18Ni9Ti stainless steel substrate by means of laser cladding. The microhardness profile of the composite coating along the depth direction was measured, while its cross-sectional microstructures and phase compositions were analyzed by means of scanning electron microscopy and X-ray diffraction. Moreover, the friction and wear behavior of the composite coatings sliding against Si 3 N 4 from ambient to 800 deg. C was evaluated using a ball-on-disc friction and wear tester, and the worn surface morphologies of the composite coatings and counterpart ceramic balls were observed using a scanning electron microscope. At the same time, the worn surfaces of the ceramic balls were also analyzed using a 3D non-contact surface mapping profiler as well. It was found that the laser cladding Ni/hBN coating on the stainless steel substrate had high microhardness and good friction-reducing and antiwear abilities at elevated temperatures up to 800 deg. C. The composite coating registered slightly increased friction coefficient and wear rate as the temperature rose from ambient to 100 deg. C; then the friction coefficient and wear rate decreased with increasing temperature up to 800 deg. C (with the slight increase in the wear rate at 700 deg. C and 800 deg. C to be an exception). The laser cladding Ni/hBN coating was dominated by mixed adhesion and abrasive wear as it slid against the ceramic ball below 300 deg. C. With further increase in the test temperature up to 400 deg. C and above, it was characterized by mild adhesion wear and plastic deformation. Since the laser cladding Ni/hBN coating registered an increased wear rate at temperatures of 600 deg. C and above, it was not suggested to be used for wear prevention and protection of the stainless steel at elevated temperature above 800 deg. C

Friction and wear behavior of laser cladding Ni/hBN self-lubricating composite coating

Energy Technology Data Exchange (ETDEWEB)

Zhang Shitang [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Graduate School, Chinese Academy of Sciences, Beijing 100039 (China); Zhou Jiansong [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Guo Baogang [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Graduate School, Chinese Academy of Sciences, Beijing 100039 (China); Zhou Huidi [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Pu Yuping [Central Iron and Steel Research Institute, Beijing 100081 (China); Chen Jianmin [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)], E-mail: chenjm@lzb.ac.cn

2008-09-15

Ni/hBN coating was successfully prepared on 1Cr18Ni9Ti stainless steel substrate by means of laser cladding. The microhardness profile of the composite coating along the depth direction was measured, while its cross-sectional microstructures and phase compositions were analyzed by means of scanning electron microscopy and X-ray diffraction. Moreover, the friction and wear behavior of the composite coatings sliding against Si{sub 3}N{sub 4} from ambient to 800 deg. C was evaluated using a ball-on-disc friction and wear tester, and the worn surface morphologies of the composite coatings and counterpart ceramic balls were observed using a scanning electron microscope. At the same time, the worn surfaces of the ceramic balls were also analyzed using a 3D non-contact surface mapping profiler as well. It was found that the laser cladding Ni/hBN coating on the stainless steel substrate had high microhardness and good friction-reducing and antiwear abilities at elevated temperatures up to 800 deg. C. The composite coating registered slightly increased friction coefficient and wear rate as the temperature rose from ambient to 100 deg. C; then the friction coefficient and wear rate decreased with increasing temperature up to 800 deg. C (with the slight increase in the wear rate at 700 deg. C and 800 deg. C to be an exception). The laser cladding Ni/hBN coating was dominated by mixed adhesion and abrasive wear as it slid against the ceramic ball below 300 deg. C. With further increase in the test temperature up to 400 deg. C and above, it was characterized by mild adhesion wear and plastic deformation. Since the laser cladding Ni/hBN coating registered an increased wear rate at temperatures of 600 deg. C and above, it was not suggested to be used for wear prevention and protection of the stainless steel at elevated temperature above 800 deg. C.

FE-DEM Analysis of the Effect of Tread Pattern on the Tractive Performance of Tires Operating on Sand

Science.gov (United States)

Nakashima, Hiroshi; Takatsu, Yuzuru; Shinone, Hisanori; Matsukawa, Hisao; Kasetani, Takahiro

Soil-tire system interaction is a fundamental and important research topic in terramechanics. We applied a 2D finite element, discrete element method (FE-DEM), using FEM for the tire and the bottom soil layer and DEM for the surface soil layer. Satisfactory performance analysis was achieved. In this study, to clarify the capabilities and limitations of the method for soil-tire interaction analysis, the tractive performance of real automobile tires with two different tread patterns—smooth and grooved—was analyzed by FE-DEM, and the numerical results compared with the experimental results obtained using an indoor traction measurement system. The analysis of tractive performance could be performed with sufficient accuracy by the proposed 2D dynamic FE-DEM. FE-DEM obtained larger drawbar pull for a tire with a grooved tread pattern, which was verified by the experimental results. Moreover, the result for the grooved tire showed almost the same gross tractive effort and similar running resistance as in experiments. However, for a tire with smooth tread pattern, the analyzed gross tractive effort and running resistance behaved differently than the experimental results, largely due to the difference in tire sinkage in FE-DEM.

Correction of radiographic measurements of acetabular cup wear for variations in pelvis orientation.

Science.gov (United States)

Derbyshire, Brian

2018-03-01

Radiographic measurement of two-dimensional acetabular cup wear is usually carried out on a series of follow-up radiographs of the patient's pelvis. Since the orientation of the pelvis might not be consistent at every X-ray examination, the resulting change in view of the wear plane introduces error into the linear wear measurement. This effect is amplified on some designs of cup in which the centre of the socket is several millimetres below the centre of the cup or circular wire marker. This study describes the formulation of a mathematical method to correct radiographic wear measurements for changes in pelvis orientation. A mathematical simulation of changes in cup orientation and wear vectors caused by pelvic tilt was used to confirm that the formulae corrected the wear exactly if the radiographic plane of the reference radiograph was parallel to the true plane of wear. An error analysis showed that even when the true wear plane was not parallel to the reference radiographic plane, the formulae could still provide a useful correction. A published correction formula was found to be ineffective.

Influence of oligomeric resins on traction and rolling resistance of silica tire treads

NARCIS (Netherlands)

Vleugels, N.; Pille-Wolf, W.; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

2016-01-01

This study concerns the silica-reinforcement of synthetic rubber compounds for passenger tire treads with the objective to gain insight into the beneficial effects of oligomeric resins, derived from natural and synthetic monomers, on the major tire performance factors: rolling resistance and (wet)

Influence of oligomeric resins on traction and rolling resistance of silica tire treads

NARCIS (Netherlands)

Vleugels, N.; Pille-Wolf, W.; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

2013-01-01

This study concerns the silica-reinforcement of synthetic rubber compounds for passenger tire treads with the objective to gain insight into the beneficial effects of oligomeric resins, derived from natural and synthetic monomers, on the major tire performance factors: Rolling Resistance and (Wet)

Influence of Tire Characteristics of Interurban Taxis on Exposure Level to Drivers Whole-Body Vibrations

Directory of Open Access Journals (Sweden)

Milad Derakhshanjazari

2016-03-01

Full Text Available Introduction: Taxi drivers’ exposure to repeat whole-body vibrations can cause back pain and digestive disorders. Since this type of vibration depends on the car components, this study was carried out to determine the influence of tire characteristics on the amount of whole-body vibrations transmitted to the Peugeot 405 taxi drivers. Methods: In this experimental study, vibration characteristics were measured according to the ISO2631-1 with each of the statuses: tubeless tires fixed and fluid in it (normal air or nitrogen and also the fluid in the tires fixed with tubes or tubeless on asphalt-paved road. Other variables including tire pressure, engine speed, road gradient, number of passengers, springs, and shock absorbers were kept constant. Then the effect of changes was analyzed using an appropriate statistical test. Results: After changing nitrogen to normal air and tubeless tires to tube, the average of RMS in Z-axis, eight-hour equivalent acceleration A(8 and crest factor were reduced (P 0.9 m/s2 to caution zone (0.45-0.9 m/s2 with a value of 0.8 m/s2. Conclusions: The amount of vibration transmitted to the whole body is sensitive to existence of tubes and tires inflation so that we can reduce the amount of whole-body vibration to lower than the upper limit of the health risk by changing the characteristics of the tire

Hybrid Soft Soil Tire Model (HSSTM). Part 1: Tire Material and Structure Modeling

Science.gov (United States)

2015-04-28

Germany. p. 18. 2. Oertel, C., On Modeling Contact and Friction Calculation of Tyre Response on Uneven Roads . Vehicle System Dynamics, 1997. 27(S1): p...touching the ground. This massless tip acts as a sensor point and can be used to detect the tire- road contact . Also, using the direction and value of the...superiority of this model as compared to other lumped parameter models currently available. Keywords: Wheeled Vehicle, Terramechanics, Off- Road

Alternate paddle configuration for improved wear resistance in the saltstone mixer

Energy Technology Data Exchange (ETDEWEB)

Reigel, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fowley, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2013-09-23

same way. The wear rate from wear test 2a was approximately double the wear rate from wear test 2b for paddle pairs 4 and 5. For both configurations, there was little or no wear on paddle pairs 1, 2, 3 and 6 based on mass change, indicating that the un-wetted and fully wetted premix materials cause less wear than the partially wetted premix. Additionally, inspection of the wear surface of the paddles showed more deformation on the flat paddles than the helical paddles which was consistent with the wear rates. Aligning of the auger discharge flight with paddle pair 1 resulted in a lower wear rate paddle pair 1 rather than having them misaligned with the feed augers. During the paddle wear tests, polishing wear was observed on the inside barrel of the mixer. The polishing wear is evident on the upper housing clamshell and the lower housing clamshell primarily at paddle pairs 4 and 5, which is the transition region of the mixer. Wear on the mixer barrel increases the space between the paddles and the barrel, resulting in increased grout build up on the barrel. Since the mixer barrel cannot be reconfigured or replaced in the SPF, the method for mitigating wear on the barrel is to move the more viscous grout through the transition region as quickly as possible. In addition, the location of the liquid inlet does not allow for sufficient cleaning of the mixer since residual grout remains on paddle pairs 1 - 4. As the paddles continue to wear and the self-cleaning capability of the paddles is lost, the lack of sufficient flushing would aid in grout build up between the barrel and the paddles which could eventually lead to decreased throughput capacity of the dry feeds. Changing the paddle configuration from flat to helical resulted in no change to the rheological properties of the grout mixture. Both tests produced a grout that is within the processing range of the SPF. Based on the results of this testing, it is recommended for the currently installed SPF mixer that paddle

Tooth wear

Directory of Open Access Journals (Sweden)

Tušek Ivan

2014-01-01

Full Text Available Tooth wear is the loss of dental hard tissue that was not caused by decay and represents a common clinical problem of modern man. In the etiology of dental hard tissue lesions there are three dominant mechanisms that may act synergistically or separately:friction (friction, which is caused by abrasion of exogenous, or attrition of endogenous origin, chemical dissolution of dental hard tissues caused by erosion, occlusal stress created by compression and flexion and tension that leads to tooth abfraction and microfracture. Wear of tooth surfaces due to the presence of microscopic imperfections of tooth surfaces is clinically manifested as sanding veneers. Tribology, as an interdisciplinary study of the mechanisms of friction, wear and lubrication at the ultrastructural level, has defined a universal model according to which the etiopathogenesis of tooth wear is caused by the following factors: health and diseases of the digestive tract, oral hygiene, eating habits, poor oral habits, bruxism, temporomandibular disorders and iatrogenic factors. Attrition and dental erosion are much more common in children with special needs (Down syndrome. Erosion of teeth usually results from diseases of the digestive tract that lead to gastroesophageal reflux (GER of gastric juice (HCl. There are two basic approaches to the assessment of the degree of wear and dental erosion. Depending on the type of wear (erosion, attrition, abfraction, the amount of calcium that was realised during the erosive attack could be determined qualitatively and quantitatively, or changes in optical properties and hardness of enamel could be recorded, too. Abrasion of teeth (abrasio dentium is the loss of dental hard tissue caused by friction between the teeth and exogenous foreign substance. It is most commonly provoked by prosthetic dentures and bad habits, while its effect depends on the size of abrasive particles and their amount, abrasive particle hardness and hardness of tooth

Upscaling of a Batch De-vulcanization Process for Ground Car Tire Rubber to a Continuous Process in a Twin Screw Extruder

NARCIS (Netherlands)

Saiwari, Sitisaiyidah; van Hoek, Johannes Wilhelmus; Dierkes, Wilma K.; Reuvekamp, Louis A.E.M.; Heideman, G.; Blume, Anke; Noordermeer, Jacobus W.M.

2016-01-01

As a means to decrease the amount of waste tires and to re-use tire rubber for new tires, devulcanization of ground passenger car tires is a promising process. Being an established process for NR and EPDM, earlier work has shown that for ground passenger car tire rubber with a relatively high amount

A new use for old tires

International Nuclear Information System (INIS)

Louie, Jacqueline

2011-01-01

This paper presents the Dreamcatcher oil spill technology developed by National Oilwell Varco Canada. The products and services using this technology can save recycled tires from the landfill, which makes the planet a greener place. The products and services in question are those used for remediating and preventing soil and water contamination. The technological products use rubber tires and degrade the rubber into two compounds. The first is the smart crumb, which is a fine rubber crumb used for oil spill adsorption on land. The second is the aqua fiber, a fiber/rubber compound that is used to adsorb oil spills on water. Both are oleophilic (oil attracting) and hydrophobic (water repelling). This allows them to filter hydrocarbons quickly from water. After the smart crumb adsorbs hydrocarbons, it is then used to make asphalt products and the aqua fiber is used to replace sand and gravel in residential and commercial concrete and asphalt respectively.

A new use for old tires

Energy Technology Data Exchange (ETDEWEB)

Louie, Jacqueline

2011-12-15

This paper presents the Dreamcatcher oil spill technology developed by National Oilwell Varco Canada. The products and services using this technology can save recycled tires from the landfill, which makes the planet a greener place. The products and services in question are those used for remediating and preventing soil and water contamination. The technological products use rubber tires and degrade the rubber into two compounds. The first is the smart crumb, which is a fine rubber crumb used for oil spill adsorption on land. The second is the aqua fiber, a fiber/rubber compound that is used to adsorb oil spills on water. Both are oleophilic (oil attracting) and hydrophobic (water repelling). This allows them to filter hydrocarbons quickly from water. After the smart crumb adsorbs hydrocarbons, it is then used to make asphalt products and the aqua fiber is used to replace sand and gravel in residential and commercial concrete and asphalt respectively.

75 FR 56991 - Grant of Authority for Subzone Status Michelin North America, Inc. (Tire Distribution and Wheel...

Science.gov (United States)

2010-09-17

... Status Michelin North America, Inc. (Tire Distribution and Wheel Assembly) Baltimore, MD Pursuant to its...; Now, therefore, the Board hereby grants authority for subzone status for activity related to tire and tire accessories warehousing and distribution and wheel assembly at the facility of Michelin North...

Effect of oxidation on the wear behavior of a ZrN coating

Energy Technology Data Exchange (ETDEWEB)

Atar, E. [Gebze Inst. of Tech., Material Science and Engineering Dept., Kocaeli (Turkey); Cimenoglu, H.; Kayali, E.S. [Istanbul Technical Univ., Dept. of Metallurgy and Materials Engineering, Azazaga, Istanbul (Turkey)

2005-07-01

In the present study tribological performance of ZrN coatings deposited on hardened AISI D2 quality cold work tool steel by arc-physical vapor deposition technique has been examined in as-deposited and oxidized conditions. ZrN coatings were oxidized at 400 C for various times up to 12 h. Reciprocating wear tests carried out by rubbing Al{sub 2}O{sub 3} balls on the coatings, revealed significant improvement in wear resistance of ZrN coating upon oxidation. Oxidation treatment at 400 C for 12 h yielded seven times higher wear resistance than as-deposited ZrN coating, beside significant reduction in the wear of counterface (Al{sub 2}O{sub 3} ball). (orig.)

Effect of oxidation on the wear behavior of a ZrN coating

International Nuclear Information System (INIS)

Atar, E.; Cimenoglu, H.; Kayali, E.S.

2005-01-01

In the present study tribological performance of ZrN coatings deposited on hardened AISI D2 quality cold work tool steel by arc-physical vapor deposition technique has been examined in as-deposited and oxidized conditions. ZrN coatings were oxidized at 400 C for various times up to 12 h. Reciprocating wear tests carried out by rubbing Al 2 O 3 balls on the coatings, revealed significant improvement in wear resistance of ZrN coating upon oxidation. Oxidation treatment at 400 C for 12 h yielded seven times higher wear resistance than as-deposited ZrN coating, beside significant reduction in the wear of counterface (Al 2 O 3 ball). (orig.)

Wear of liquid nitrogen-cooled 440C bearing steels in an oxygen environment

Science.gov (United States)

Chaudhuri, Dilip K.; Verma, Ravi

1988-01-01

This paper presents up-to-date findings of the research being conducted to understand the mechanism of sliding wear in unlubricated 440C bearing steels under oxidative conditions. A sliding wear test rig has been designed and built with a cylinder-on-flat geometry. The equipment is capable of testing specimens under high axial loads and sliding speeds in a simulated LOX environment. Samples of 440C steel, quenched and tempered to a hardness of Rc 56, were tested under a load of 890 N and a sliding speed of 2.05 m/sec for total sliding distances of up to 5.54 km. Flash temperatures during these tests were measured with an IR camera and a fast digital recorder. Microstructural and microanalytical data from the worn surfaces and the debris particles are analyzed extensively, along with wear rates, flash temperatures, surface profiles, hardnesses, and residual stresses, in the context of oxidation and wear theories.

Spin-inversion in nanoscale graphene sheets with a Rashba spin-orbit barrier

Directory of Open Access Journals (Sweden)

Somaieh Ahmadi

2012-03-01

Full Text Available Spin-inversion properties of an electron in nanoscale graphene sheets with a Rashba spin-orbit barrier is studied using transfer matrix method. It is found that for proper values of Rashba spin-orbit strength, perfect spin-inversion can occur in a wide range of electron incident angle near the normal incident. In this case, the graphene sheet with Rashba spin-orbit barrier can be considered as an electron spin-inverter. The efficiency of spin-inverter can increase up to a very high value by increasing the length of Rashba spin-orbit barrier. The effect of intrinsic spin-orbit interaction on electron spin inversion is then studied. It is shown that the efficiency of spin-inverter decreases slightly in the presence of intrinsic spin-orbit interaction. The present study can be used to design graphene-based spintronic devices.