Directory of Open Access Journals (Sweden)
Don-Roger Parkinson
2016-02-01
Full Text Available Water samples were collected and analyzed for conductivity, pH, temperature and trihalomethanes (THMs during the fall of 2014 at two monitored municipal drinking water source ponds. Both spot (or grab and time weighted average (TWA sampling methods were assessed over the same two day sampling time period. For spot sampling, replicate samples were taken at each site and analyzed within 12 h of sampling by both Headspace (HS- and direct (DI- solid phase microextraction (SPME sampling/extraction methods followed by Gas Chromatography/Mass Spectrometry (GC/MS. For TWA, a two day passive on-site TWA sampling was carried out at the same sampling points in the ponds. All SPME sampling methods undertaken used a 65-µm PDMS/DVB SPME fiber, which was found optimal for THM sampling. Sampling conditions were optimized in the laboratory using calibration standards of chloroform, bromoform, bromodichloromethane, dibromochloromethane, 1,2-dibromoethane and 1,2-dichloroethane, prepared in aqueous solutions from analytical grade samples. Calibration curves for all methods with R2 values ranging from 0.985–0.998 (N = 5 over the quantitation linear range of 3–800 ppb were achieved. The different sampling methods were compared for quantification of the water samples, and results showed that DI- and TWA- sampling methods gave better data and analytical metrics. Addition of 10% wt./vol. of (NH42SO4 salt to the sampling vial was found to aid extraction of THMs by increasing GC peaks areas by about 10%, which resulted in lower detection limits for all techniques studied. However, for on-site TWA analysis of THMs in natural waters, the calibration standard(s ionic strength conditions, must be carefully matched to natural water conditions to properly quantitate THM concentrations. The data obtained from the TWA method may better reflect actual natural water conditions.
Koziel, Jacek A; Nguyen, Lam T; Glanville, Thomas D; Ahn, Heekwon; Frana, Timothy S; Hans van Leeuwen, J
2017-10-01
A passive sampling method, using retracted solid-phase microextraction (SPME) - gas chromatography-mass spectrometry and time-weighted averaging, was developed and validated for tracking marker volatile organic compounds (VOCs) emitted during aerobic digestion of biohazardous animal tissue. The retracted SPME configuration protects the fragile fiber from buffeting by the process gas stream, and it requires less equipment and is potentially more biosecure than conventional active sampling methods. VOC concentrations predicted via a model based on Fick's first law of diffusion were within 6.6-12.3% of experimentally controlled values after accounting for VOC adsorption to the SPME fiber housing. Method detection limits for five marker VOCs ranged from 0.70 to 8.44ppbv and were statistically equivalent (p>0.05) to those for active sorbent-tube-based sampling. The sampling time of 30min and fiber retraction of 5mm were found to be optimal for the tissue digestion process. Copyright © 2017 Elsevier Ltd. All rights reserved.
Baimatova, Nassiba; Koziel, Jacek A; Kenessov, Bulat
2015-05-11
A new and simple method for benzene, toluene, ethylbenzene and o-xylene (BTEX) quantification in vehicle exhaust was developed based on diffusion-controlled extraction onto a retracted solid-phase microextraction (SPME) fiber coating. The rationale was to develop a method based on existing and proven SPME technology that is feasible for field adaptation in developing countries. Passive sampling with SPME fiber retracted into the needle extracted nearly two orders of magnitude less mass (n) compared with exposed fiber (outside of needle) and sampling was in a time weighted-averaging (TWA) mode. Both the sampling time (t) and fiber retraction depth (Z) were adjusted to quantify a wider range of Cgas. Extraction and quantification is conducted in a non-equilibrium mode. Effects of Cgas, t, Z and T were tested. In addition, contribution of n extracted by metallic surfaces of needle assembly without SPME coating was studied. Effects of sample storage time on n loss was studied. Retracted TWA-SPME extractions followed the theoretical model. Extracted n of BTEX was proportional to Cgas, t, Dg, T and inversely proportional to Z. Method detection limits were 1.8, 2.7, 2.1 and 5.2 mg m(-3) (0.51, 0.83, 0.66 and 1.62 ppm) for BTEX, respectively. The contribution of extraction onto metallic surfaces was reproducible and influenced by Cgas and t and less so by T and by the Z. The new method was applied to measure BTEX in the exhaust gas of a Ford Crown Victoria 1995 and compared with a whole gas and direct injection method. Copyright © 2015 Elsevier B.V. All rights reserved.
Measurement of average radon gas concentration at workplaces
International Nuclear Information System (INIS)
Kavasi, N.; Somlai, J.; Kovacs, T.; Gorjanacz, Z.; Nemeth, Cs.; Szabo, T.; Varhegyi, A.; Hakl, J.
2003-01-01
In this paper results of measurement of average radon gas concentration at workplaces (the schools and kindergartens and the ventilated workplaces) are presented. t can be stated that the one month long measurements means very high variation (as it is obvious in the cases of the hospital cave and the uranium tailing pond). Consequently, in workplaces where the expectable changes of radon concentration considerable with the seasons should be measure for 12 months long. If it is not possible, the chosen six months period should contain summer and winter months as well. The average radon concentration during working hours can be differ considerable from the average of the whole time in the cases of frequent opening the doors and windows or using artificial ventilation. (authors)
Understanding coastal morphodynamic patterns from depth-averaged sediment concentration
Ribas, F.; Falques, A.; de Swart, H. E.; Dodd, N.; Garnier, R.; Calvete, D.
This review highlights the important role of the depth-averaged sediment concentration (DASC) to understand the formation of a number of coastal morphodynamic features that have an alongshore rhythmic pattern: beach cusps, surf zone transverse and crescentic bars, and shoreface-connected sand
Concentration fluctuations and averaging time in vapor clouds
Wilson, David J
2010-01-01
This book contributes to more reliable and realistic predictions by focusing on sampling times from a few seconds to a few hours. Its objectives include developing clear definitions of statistical terms, such as plume sampling time, concentration averaging time, receptor exposure time, and other terms often confused with each other or incorrectly specified in hazard assessments; identifying and quantifying situations for which there is no adequate knowledge to predict concentration fluctuations in the near-field, close to sources, and far downwind where dispersion is dominated by atmospheric t
DEFF Research Database (Denmark)
Huang, Jianyin; Bennett, William W.; Welsh, David T.
2016-01-01
Commercially-available AMI-7001 anion exchange and CMI-7000 cation exchange membranes were utilised as binding layers for DGT measurements of NO3-N and NH4-N in freshwaters. These ion exchange membranes are easier to prepare and handle than DGT binding layers consisting of hydrogels cast with ion...... exchange resins. The membranes showed good uptake and elution efficiencies for both NO3-N and NH4-N. The membrane-based DGTs are suitable for pH 3.5-8.5 and ionic strength ranges (0.0001-0.014 and 0.0003-0.012 mol L−1 as NaCl for the AMI-7001 and CMI-7000 membrane, respectively) typical of most natural...... freshwaters. The binding membranes had high intrinsic binding capacities for NO3-N and NH4-N of 911 ± 88 μg and 3512 ± 51 μg, respectively. Interferences from the major competing ions for membrane-based DGTs are similar to DGTs employing resin-based binding layers but with slightly different selectivity...
40 CFR 80.1238 - How is a refinery's or importer's average benzene concentration determined?
2010-07-01
... concentration determined? (a) The average benzene concentration of gasoline produced at a refinery or imported... percent benzene). i = Individual batch of gasoline produced at the refinery or imported during the applicable averaging period. n = Total number of batches of gasoline produced at the refinery or imported...
38 CFR 4.76a - Computation of average concentric contraction of visual fields.
2010-07-01
... concentric contraction of visual fields. 4.76a Section 4.76a Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS SCHEDULE FOR RATING DISABILITIES Disability Ratings The Organs of Special Sense § 4.76a Computation of average concentric contraction of visual fields. Table III—Normal Visual...
Variation in the annual average radon concentration measured in homes in Mesa County, Colorado
International Nuclear Information System (INIS)
Rood, A.S.; George, J.L.; Langner, G.H. Jr.
1990-04-01
The purpose of this study is to examine the variability in the annual average indoor radon concentration. The TMC has been collecting annual average radon data for the past 5 years in 33 residential structures in Mesa County, Colorado. This report is an interim report that presents the data collected up to the present. Currently, the plans are to continue this study in the future. 62 refs., 3 figs., 12 tabs
Parameterization of Time-Averaged Suspended Sediment Concentration in the Nearshore
Directory of Open Access Journals (Sweden)
Hyun-Doug Yoon
2015-11-01
Full Text Available To quantify the effect of wave breaking turbulence on sediment transport in the nearshore, the vertical distribution of time-averaged suspended sediment concentration (SSC in the surf zone was parameterized in terms of the turbulent kinetic energy (TKE at different cross-shore locations, including the bar crest, bar trough, and inner surf zone. Using data from a large-scale laboratory experiment, a simple relationship was developed between the time-averaged SSC and the time-averaged TKE. The vertical variation of the time-averaged SSC was fitted to an equation analogous to the turbulent dissipation rate term. At the bar crest, the proposed equation was slightly modified to incorporate the effect of near-bed sediment processes and yielded reasonable agreement. This parameterization yielded the best agreement at the bar trough, with a coefficient of determination R2 ≥ 0.72 above the bottom boundary layer. The time-averaged SSC in the inner surf zone showed good agreement near the bed but poor agreement near the water surface, suggesting that there is a different sedimentation mechanism that controls the SSC in the inner surf zone.
Protocol for the estimation of average indoor radon-daughter concentrations: Second edition
International Nuclear Information System (INIS)
Langner, G.H. Jr.; Pacer, J.C.
1988-05-01
The Technical Measurements Center has developed a protocol which specifies the procedures to be used for determining indoor radon-daughter concentrations in support of Department of Energy remedial action programs. This document is the central part of the protocol and is to be used in conjunction with the individual procedure manuals. The manuals contain the information and procedures required to implement the proven methods for estimating average indoor radon-daughter concentration. Proven in this case means that these methods have been determined to provide reasonable assurance that the average radon-daughter concentration within a structure is either above, at, or below the standards established for remedial action programs. This document contains descriptions of the generic aspects of methods used for estimating radon-daughter concentration and provides guidance with respect to method selection for a given situation. It is expected that the latter section of this document will be revised whenever another estimation method is proven to be capable of satisfying the criteria of reasonable assurance and cost minimization. 22 refs., 6 figs., 3 tabs
International Nuclear Information System (INIS)
Esh, D.W.; Pinkston, K.E.; Barr, C.S.; Bradford, A.H.; Ridge, A.Ch.
2009-01-01
Nuclear Regulatory Commission (NRC) staff has developed a concentration averaging approach and guidance for the review of Department of Energy (DOE) non-HLW determinations. Although the approach was focused on this specific application, concentration averaging is generally applicable to waste classification and thus has implications for waste management decisions as discussed in more detail in this paper. In the United States, radioactive waste has historically been classified into various categories for the purpose of ensuring that the disposal system selected is commensurate with the hazard of the waste such that public health and safety will be protected. However, the risk from the near-surface disposal of radioactive waste is not solely a function of waste concentration but is also a function of the volume (quantity) of waste and its accessibility. A risk-informed approach to waste classification for near-surface disposal of low-level waste would consider the specific characteristics of the waste, the quantity of material, and the disposal system features that limit accessibility to the waste. NRC staff has developed example analytical approaches to estimate waste concentration, and therefore waste classification, for waste disposed in facilities or with configurations that were not anticipated when the regulation for the disposal of commercial low-level waste (i.e. 10 CFR Part 61) was developed. (authors)
Husna, Husyira Al; Ota, Yasuyuki; Minemoto, Takashi; Nishioka, Kensuke
2015-08-01
The concentrator photovoltaic (CPV) system is unique and different from the common flat-plate PV system. It uses a multi-junction solar cell and a Fresnel lens to concentrate direct solar radiation onto the cell while tracking the sun throughout the day. The cell efficiency could reach over 40% under high concentration ratio. In this study, we analyzed a one year set of environmental condition data of the University of Miyazaki, Japan, where the CPV system was installed. Performance ratio (PR) was discussed to describe the system’s performance. Meanwhile, the average photon energy (APE) was used to describe the spectrum distribution at the site where the CPV system was installed. A circuit simulator network was used to simulate the CPV system electrical characteristics under various environmental conditions. As for the result, we found that the PR of the CPV systems depends on the APE level rather than the cell temperature.
Average concentrations of FSH and LH in seminal plasma as determined by radioimmunoassay
International Nuclear Information System (INIS)
Milbradt, R.; Linzbach, P.; Feller, H.
1979-01-01
In 322 males, 25 to 50 years of age, levels of LH and FSH respectively were determined in seminal plasma by radioimmunoassay. Average values of 0,78 ng/ml and 3,95 ng/ml were found as for FSH and LH respectively. Sperm count and motility were not related to FSH levels, but were to LH levels. A high count of spermatozoa corresponded to high concentration of LH, and normal motility was associated with higher levels of LH as compared to levels associated with asthenozoospermia. With respect to count of spermatozoa of a single or the average patient, it is suggested that the ratio of FSH/LH would be more meaningful than LH level alone. (orig.) [de
Time-Weighted Balanced Stochastic Model Reduction
DEFF Research Database (Denmark)
Tahavori, Maryamsadat; Shaker, Hamid Reza
2011-01-01
A new relative error model reduction technique for linear time invariant (LTI) systems is proposed in this paper. Both continuous and discrete time systems can be reduced within this framework. The proposed model reduction method is mainly based upon time-weighted balanced truncation and a recently...
Gryaznov, D.; Fleig, J.; Maier, J.
2008-03-01
Whipple's solution of the problem of grain boundary diffusion and Le Claire's relation, which is often used to determine grain boundary diffusion coefficients, are examined for a broad range of ratios of grain boundary to bulk diffusivities Δ and diffusion times t. Different reasons leading to errors in determining the grain boundary diffusivity (DGB) when using Le Claire's relation are discussed. It is shown that nonlinearities of the diffusion profiles in lnCav-y6/5 plots and deviations from "Le Claire's constant" (-0.78) are the major error sources (Cav=averaged concentration, y =coordinate in diffusion direction). An improved relation (replacing Le Claire's constant) is suggested for analyzing diffusion profiles particularly suited for small diffusion lengths (short times) as often required in diffusion experiments on nanocrystalline materials.
Uncertainties of estimating average radon and radon decay product concentrations in occupied houses
International Nuclear Information System (INIS)
Ronca-Battista, M.; Magno, P.; Windham, S.
1986-01-01
Radon and radon decay product measurements made in up to 68 Butte, Montana homes over a period of 18 months were used to estimate the uncertainty in estimating long-term average radon and radon decay product concentrations from a short-term measurement. This analysis was performed in support of the development of radon and radon decay product measurement protocols by the Environmental Protection Agency (EPA). The results of six measurement methods were analyzed: continuous radon and working level monitors, radon progeny integrating sampling units, alpha-track detectors, and grab radon and radon decay product techniques. Uncertainties were found to decrease with increasing sampling time and to be smaller when measurements were conducted during the winter months. In general, radon measurements had a smaller uncertainty than radon decay product measurements. As a result of this analysis, the EPA measurements protocols specify that all measurements be made under closed-house (winter) conditions, and that sampling times of at least a 24 hour period be used when the measurement will be the basis for a decision about remedial action or long-term health risks. 13 references, 3 tables
Average daily and annual courses of 222Rn concentration in some natural medium
International Nuclear Information System (INIS)
Holy, K.; Bohm, R.; Polaskova, A.; Stelina, J.; Sykora, I.; Hola, O.
1996-01-01
Simultaneous measurements of the 222 Rn concentration in the outdoor atmosphere of Bratislava and in the soil air over one year period have been made. Daily and seasonal variations of the 222 Rn concentration in both media were found. Some attributes of these variations as well as methods of measurements are presented in this work. (author). 17 refs., 6 figs
DEFF Research Database (Denmark)
Pedersen, Ken Steen; Skrubel, Rikke; Stege, Helle
2012-01-01
Background The objective of this study was to investigate the association between average daily gain and the number of Lawsonia intracellularis bacteria in faeces of growing pigs with different levels of diarrhoea. Methods A longitudinal field study (n?=?150 pigs) was performed in a Danish herd f...
Sources Contributing to the Average Extracellular Concentration of Dopamine in the Nucleus Accumbens
Owesson-White, CA; Roitman, MF; Sombers, LA; Belle, AM; Keithley, RB; Peele, JL; Carelli, RM; Wightman, RM
2012-01-01
Mesolimbic dopamine neurons fire in both tonic and phasic modes resulting in detectable extracellular levels of dopamine in the nucleus accumbens (NAc). In the past, different techniques have targeted dopamine levels in the NAc to establish a basal concentration. In this study we used in vivo fast scan cyclic voltammetry (FSCV) in the NAc of awake, freely moving rats. The experiments were primarily designed to capture changes in dopamine due to phasic firing – that is, the measurement of dopa...
Directory of Open Access Journals (Sweden)
P. Jančík
2013-10-01
Full Text Available The goal of the article is to present analysis of metallurgical industry contribution to annual average PM10 concentrations in Moravian-Silesian based on means of the air pollution modelling in accord with the Czech reference methodology SYMOS´97.
The average concentrations of 226Ra and 210Pb in foodstuff cultivated in the Pocos de Caldas plateau
International Nuclear Information System (INIS)
Hollanda Vasconcellos, L.M. de.
1984-01-01
The average concentrations of 226 Ra and 210 Pb in vegetables cultivated in the Pocos de Caldas plateau, mainly potatoes, carrots, beans and corn and the estimation of the average transfer factors soil-foodstuff for both radionuclides, were performed. The total 226 Ra and 210 Pb content in the soil was determined by gamma spectrometry. The exchangeable fraction was obtained by the classical radon emanation procedure and the 210 Pb was isolated by a radiochemical procedure and determined by radiometry of its daughter 210 Bi beta emissions with a Geiger Muller Counter. (M.A.C.) [pt
International Nuclear Information System (INIS)
Janik, M.; Loskiewicz, J.; Olko, P.; Swakon, J.
1998-01-01
Radon concentration in outdoor air and in buildings is very variable, showing diurnal and seasonal variations. Long term track etch detectors measurements lasting up to one year give the most precise one year averages. It arrives, however, that we are obliged to get results much sooner e.g. for screening measurements. How long should we measure to get proper results? We have studied the problem of selecting proper time interval on the basis of our five long term (ca. 30 days) measurements in Cracow using AlphaGUARD ionization chamber detector. The mean radon concentration ranged from 543 to 1107 Bq/m 3 . It was found that the relative error of k day average was decreasing exponentially with a time constant of 4 days. Therefore we recommended a minimal measuring time of four (k = 4) and better six days. (author)
Wasiczko, Linda M.; Smolyaninov, Igor I.; Davis, Christopher C.
2004-01-01
Free space optics (FSO) is one solution to the bandwidth bottleneck resulting from increased demand for broadband access. It is well known that atmospheric turbulence distorts the wavefront of a laser beam propagating through the atmosphere. This research investigates methods of reducing the effects of intensity scintillation and beam wander on the performance of free space optical communication systems, by characterizing system enhancement using either aperture averaging techniques or nonimaging optics. Compound Parabolic Concentrators, nonimaging optics made famous by Winston and Welford, are inexpensive elements that may be easily integrated into intensity modulation-direct detection receivers to reduce fading caused by beam wander and spot breakup in the focal plane. Aperture averaging provides a methodology to show the improvement of a given receiver aperture diameter in averaging out the optical scintillations over the received wavefront.
International Nuclear Information System (INIS)
Collignan, Bernard; Powaga, Emilie
2014-01-01
Risk assessment due to radon exposure indoors is based on annual average indoor radon activity concentration. To assess the radon exposure in a building, measurement is generally performed during at least two months during heating period in order to be representative of the annual average value. This is because radon presence indoors could be very variable during time. This measurement protocol is fairly reliable but may be a limiting in the radon risk management, particularly during a real estate transaction due to the duration of the measurement and the limitation of the measurement period. A previous field study defined a rapid methodology to characterize radon entry in dwellings. The objective of this study was at first, to test this methodology in various dwellings to assess its relevance with a daily test. At second, a ventilation model was used to assess numerically the air renewal of a building, the indoor air quality all along the year and the annual average indoor radon activity concentration, based on local meteorological conditions, some building characteristics and in-situ characterization of indoor pollutant emission laws. Experimental results obtained on thirteen individual dwellings showed that it is generally possible to obtain a representative characterization of radon entry into homes. It was also possible to refine the methodology defined in the previous study. In addition, numerical assessments of annual average indoor radon activity concentration showed generally a good agreement with measured values. These results are encouraging to allow a procedure with a short measurement time to be used to characterize long-term radon potential in dwellings. - Highlights: • Test of a daily procedure to characterize radon potential in dwellings. • Numerical assessment of the annual radon concentration. • Procedure applied on thirteen dwellings, characterization generally satisfactory. • Procedure useful to manage radon risk in dwellings, for real
Directory of Open Access Journals (Sweden)
Jia-heng Zhao
2017-10-01
Full Text Available This paper presents numerical simulations of dam-break flow over a movable bed. Two different mathematical models were compared: a fully coupled formulation of shallow water equations with erosion and deposition terms (a depth-averaged concentration flux model, and shallow water equations with a fully coupled Exner equation (a bed load flux model. Both models were discretized using the cell-centered finite volume method, and a second-order Godunov-type scheme was used to solve the equations. The numerical flux was calculated using a Harten, Lax, and van Leer approximate Riemann solver with the contact wave restored (HLLC. A novel slope source term treatment that considers the density change was introduced to the depth-averaged concentration flux model to obtain higher-order accuracy. A source term that accounts for the sediment flux was added to the bed load flux model to reflect the influence of sediment movement on the momentum of the water. In a one-dimensional test case, a sensitivity study on different model parameters was carried out. For the depth-averaged concentration flux model, Manning's coefficient and sediment porosity values showed an almost linear relationship with the bottom change, and for the bed load flux model, the sediment porosity was identified as the most sensitive parameter. The capabilities and limitations of both model concepts are demonstrated in a benchmark experimental test case dealing with dam-break flow over variable bed topography.
Directory of Open Access Journals (Sweden)
I. N. Polonsky
2014-04-01
Full Text Available GeoCARB is a proposed instrument to measure column averaged concentrations of CO2, CH4 and CO from geostationary orbit using reflected sunlight in near-infrared absorption bands of the gases. The scanning options, spectral channels and noise characteristics of geoCARB and two descope options are described. The accuracy of concentrations from geoCARB data is investigated using end-to-end retrievals; spectra at the top of the atmosphere in the geoCARB bands are simulated with realistic trace gas profiles, meteorology, aerosol, cloud and surface properties, and then the concentrations of CO2, CH4 and CO are estimated from the spectra after addition of noise characteristic of geoCARB. The sensitivity of the algorithm to aerosol, the prior distributions assumed for the gases and the meteorology are investigated. The contiguous spatial sampling and fine temporal resolution of geoCARB open the possibility of monitoring localised sources such as power plants. Simulations of emissions from a power plant with a Gaussian plume are conducted to assess the accuracy with which the emission strength may be recovered from geoCARB spectra. Scenarios for "clean" and "dirty" power plants are examined. It is found that a reliable estimate of the emission rate is possible, especially for power plants that have particulate filters, by averaging emission rates estimated from multiple snapshots of the CO2 field surrounding the plant. The result holds even in the presence of partial cloud cover.
International Nuclear Information System (INIS)
George, J.L.
1988-04-01
One of the measurement needs of US Department of Energy (DOE) remedial action programs is the estimation of the annual-average indoor radon-daughter concentration (RDC) in structures. The filtered alpha-track method, using a 1-year exposure period, can be used to accomplish RDC estimations for the DOE remedial action programs. This manual describes the procedure used to obtain filtered alpha-track measurements to derive average RDC estimates from the measurrements. Appropriate quality-assurance and quality-control programs are also presented. The ''prompt'' alpha-track method of exposing monitors for 2 to 6 months during specific periods of the year is also briefly discussed in this manual. However, the prompt alpha-track method has been validated only for use in the Mesa County, Colorado, area. 3 refs., 3 figs
International Nuclear Information System (INIS)
Daddy Setyawan
2011-01-01
There are several passive safety systems on APWR reactor design. One of the passive safety system is the cooling system with natural circulation air on the surface of concentric vertical cylinder containment wall. Since the natural circulation air performance in the Passive Containment Cooling System (PCCS) application is related to safety, the cooling characteristics of natural circulation air on concentric vertical cylinder containment wall should be studied experimentally. This paper focuses on the experimental study of the heat transfer coefficient of natural circulation air with heat flux level varied on the characteristics of APWR concentric vertical cylinder containment wall. The procedure of this experimental study is composed of 4 stages as follows: the design of APWR containment with scaling 1:40, the assembling of APWR containment with its instrumentation, calibration and experimentation. The experimentation was conducted in the transient and steady-state with the variation of heat flux, from 119 W/m 2 until 575 W/m 2 . From The experimentation result obtained average heat transfer empirical correlation of natural convection Nu L = 0,008(Ra * L ) 0,68 for the concentric vertical cylinder geometry modelling of APWR. (author)
Directory of Open Access Journals (Sweden)
C. S. Malley
2018-03-01
Full Text Available Exposure to nitrogen dioxide (NO2 is associated with negative human health effects, both for short-term peak concentrations and from long-term exposure to a wider range of NO2 concentrations. For the latter, the European Union has established an air quality limit value of 40 µg m−3 as an annual average. However, factors such as proximity and strength of local emissions, atmospheric chemistry, and meteorological conditions mean that there is substantial variation in the hourly NO2 concentrations contributing to an annual average concentration. The aim of this analysis was to quantify the nature of this variation at thousands of monitoring sites across Europe through the calculation of a standard set of chemical climatology statistics. Specifically, at each monitoring site that satisfied data capture criteria for inclusion in this analysis, annual NO2 concentrations, as well as the percentage contribution from each month, hour of the day, and hourly NO2 concentrations divided into 5 µg m−3 bins were calculated. Across Europe, 2010–2014 average annual NO2 concentrations (NO2AA exceeded the annual NO2 limit value at 8 % of > 2500 monitoring sites. The application of this chemical climatology approach showed that sites with distinct monthly, hour of day, and hourly NO2 concentration bin contributions to NO2AA were not grouped into specific regions of Europe, furthermore, within relatively small geographic regions there were sites with similar NO2AA, but with differences in these contributions. Specifically, at sites with highest NO2AA, there were generally similar contributions from across the year, but there were also differences in the contribution of peak vs. moderate hourly NO2 concentrations to NO2AA, and from different hours across the day. Trends between 2000 and 2014 for 259 sites indicate that, in general, the contribution to NO2AA from winter months has increased, as has the contribution from the rush-hour periods of
Malley, Christopher S.; von Schneidemesser, Erika; Moller, Sarah; Braban, Christine F.; Hicks, W. Kevin; Heal, Mathew R.
2018-03-01
Exposure to nitrogen dioxide (NO2) is associated with negative human health effects, both for short-term peak concentrations and from long-term exposure to a wider range of NO2 concentrations. For the latter, the European Union has established an air quality limit value of 40 µg m-3 as an annual average. However, factors such as proximity and strength of local emissions, atmospheric chemistry, and meteorological conditions mean that there is substantial variation in the hourly NO2 concentrations contributing to an annual average concentration. The aim of this analysis was to quantify the nature of this variation at thousands of monitoring sites across Europe through the calculation of a standard set of chemical climatology statistics. Specifically, at each monitoring site that satisfied data capture criteria for inclusion in this analysis, annual NO2 concentrations, as well as the percentage contribution from each month, hour of the day, and hourly NO2 concentrations divided into 5 µg m-3 bins were calculated. Across Europe, 2010-2014 average annual NO2 concentrations (NO2AA) exceeded the annual NO2 limit value at 8 % of > 2500 monitoring sites. The application of this chemical climatology approach showed that sites with distinct monthly, hour of day, and hourly NO2 concentration bin contributions to NO2AA were not grouped into specific regions of Europe, furthermore, within relatively small geographic regions there were sites with similar NO2AA, but with differences in these contributions. Specifically, at sites with highest NO2AA, there were generally similar contributions from across the year, but there were also differences in the contribution of peak vs. moderate hourly NO2 concentrations to NO2AA, and from different hours across the day. Trends between 2000 and 2014 for 259 sites indicate that, in general, the contribution to NO2AA from winter months has increased, as has the contribution from the rush-hour periods of the day, while the contribution from
International Nuclear Information System (INIS)
George, J.L.
1986-04-01
The US Department of Energy (DOE) Office of Remedial Action and Waste Technology established the Technical Measurements Center to provide standardization, calibration, comparability, verification of data, quality assurance, and cost-effectiveness for the measurement requirements of DOE remedial action programs. One of the remedial-action measurement needs is the estimation of average indoor radon-daughter concentration. One method for accomplishing such estimations in support of DOE remedial action programs is the radon grab-sampling method. This manual describes procedures for radon grab sampling, with the application specifically directed to the estimation of average indoor radon-daughter concentration (RDC) in highly ventilated structures. This particular application of the measurement method is for cases where RDC estimates derived from long-term integrated measurements under occupied conditions are below the standard and where the structure being evaluated is considered to be highly ventilated. The radon grab-sampling method requires that sampling be conducted under standard maximized conditions. Briefly, the procedure for radon grab sampling involves the following steps: selection of sampling and counting equipment; sample acquisition and processing, including data reduction; calibration of equipment, including provisions to correct for pressure effects when sampling at various elevations; and incorporation of quality-control and assurance measures. This manual describes each of the above steps in detail and presents an example of a step-by-step radon grab-sampling procedure using a scintillation cell
Energy Technology Data Exchange (ETDEWEB)
Kretzschmar, J.G.; Mertens, I.
1984-01-01
Over the period 1977-1979, hourly meteorological measurements at the Nuclear Energy Research Centre, Mol, Belgium and simultaneous synoptic observations at the nearby military airport of Kleine Brogel, have been compiled as input data for a bi-Gaussian dispersion model. The available information has first of all been used to determine hourly stability classes in ten widely used turbulent diffusion typing schemes. Systematic correlations between different systems were rare. Twelve different combinations of diffusion typing scheme-dispersion parameters were then used for calculating cumulative frequency distributions of 1 h, 8 h, 16 h, 3 d, and 26 d average ground-level concentrations at receptors respectively at 500 m, 1 km, 2 km, 4 km and 8 km from continuous ground-level release and an elevated release at 100 m height. Major differences were noted as well in the extreme values, the higher percentiles, as in the annual mean concentrations. These differences are almost entirely due to the differences in the numercial values (as a function of distance) of the various sets of dispersion parameters actually in use for impact assessment studies. Dispersion parameter sets giving the lowest normalized ground-level concentration values for ground level releases give the highest results for elevated releases and vice versa. While it was illustrated once again that the applicability of a given set of dispersion parameters is restricted due to the specific conditions under which the given set derived, it was also concluded that systematic experimental work to validate certain assumptions is urgently needed.
Zhai, Binxu; Chen, Jianguo
2018-04-18
A stacked ensemble model is developed for forecasting and analyzing the daily average concentrations of fine particulate matter (PM 2.5 ) in Beijing, China. Special feature extraction procedures, including those of simplification, polynomial, transformation and combination, are conducted before modeling to identify potentially significant features based on an exploratory data analysis. Stability feature selection and tree-based feature selection methods are applied to select important variables and evaluate the degrees of feature importance. Single models including LASSO, Adaboost, XGBoost and multi-layer perceptron optimized by the genetic algorithm (GA-MLP) are established in the level 0 space and are then integrated by support vector regression (SVR) in the level 1 space via stacked generalization. A feature importance analysis reveals that nitrogen dioxide (NO 2 ) and carbon monoxide (CO) concentrations measured from the city of Zhangjiakou are taken as the most important elements of pollution factors for forecasting PM 2.5 concentrations. Local extreme wind speeds and maximal wind speeds are considered to extend the most effects of meteorological factors to the cross-regional transportation of contaminants. Pollutants found in the cities of Zhangjiakou and Chengde have a stronger impact on air quality in Beijing than other surrounding factors. Our model evaluation shows that the ensemble model generally performs better than a single nonlinear forecasting model when applied to new data with a coefficient of determination (R 2 ) of 0.90 and a root mean squared error (RMSE) of 23.69μg/m 3 . For single pollutant grade recognition, the proposed model performs better when applied to days characterized by good air quality than when applied to days registering high levels of pollution. The overall classification accuracy level is 73.93%, with most misclassifications made among adjacent categories. The results demonstrate the interpretability and generalizability of
Canozzi, Maria Eugênia Andrighetto; Mederos, America; Manteca, Xavier; Turner, Simon; McManus, Concepta; Zago, Daniele; Barcellos, Júlio Otávio Jardim
2017-10-01
A systematic review and meta-analysis (MA) were performed to summarize all scientific evidence for the effects of castration in male beef cattle on welfare indicators based on cortisol concentration, average daily gain (ADG), and vocalization. We searched five electronic databases, conference proceedings, and experts were contacted electronically. The main inclusion criteria involved completed studies using beef cattle up to one year of age undergoing surgical and non-surgical castration that presented cortisol concentration, ADG, or vocalization as an outcome. A random effect MA was conducted for each indicator separately with the mean of the control and treated groups. A total of 20 publications reporting 26 studies and 162 trials were included in the MA involving 1814 cattle. Between study heterogeneity was observed when analysing cortisol (I 2 =56.7%) and ADG (I 2 =79.6%). Surgical and non-surgical castration without drug administration compared to uncastrated animals showed no change (P≥0.05) in cortisol level. Multimodal therapy for pain did not decrease (P≥0.05) cortisol concentration after 30min when non-surgical castration was performed. Comparison between surgical castration, with and without anaesthesia, showed a tendency (P=0.077) to decrease cortisol levels after 120min of intervention. Non-surgical and surgical castration, performed with no pain mitigation, increased and tended to increase the ADG by 0.814g/d (P=0.001) and by 0.140g/d (P=0.091), respectively, when compared to a non-castrated group. Our MA study demonstrates an inconclusive result to draw recommendations on preferred castration practices to minimize pain in beef cattle. Copyright © 2017 Elsevier Ltd. All rights reserved.
Hochadel, Matthias; Heinrich, Joachim; Gehring, Ulrike; Morgenstern, Verena; Kuhlbusch, Thomas; Link, Elke; Wichmann, H.-Erich; Krämer, Ursula
Global regression models were developed to estimate individual levels of long-term exposure to traffic-related air pollutants. The models are based on data of a one-year measurement programme including geographic data on traffic and population densities. This investigation is part of a cohort study on the impact of traffic-related air pollution on respiratory health, conducted at the westerly end of the Ruhr-area in North-Rhine Westphalia, Germany. Concentrations of NO 2, fine particle mass (PM 2.5) and filter absorbance of PM 2.5 as a marker for soot were measured at 40 sites spread throughout the study region. Fourteen-day samples were taken between March 2002 and March 2003 for each season and site. Annual average concentrations for the sites were determined after adjustment for temporal variation. Information on traffic counts in major roads, building densities and community population figures were collected in a geographical information system (GIS). This information was used to calculate different potential traffic-based predictors: (a) daily traffic flow and maximum traffic intensity of buffers with radii from 50 to 10 000 m and (b) distances to main roads and highways. NO 2 concentration and PM 2.5 absorbance were strongly correlated with the traffic-based variables. Linear regression prediction models, which involved predictors with radii of 50 to 1000 m, were developed for the Wesel region where most of the cohort members lived. They reached a model fit ( R2) of 0.81 and 0.65 for NO 2 and PM 2.5 absorbance, respectively. Regression models for the whole area required larger spatial scales and reached R2=0.90 and 0.82. Comparison of predicted values with NO 2 measurements at independent public monitoring stations showed a satisfactory association ( r=0.66). PM 2.5 concentration, however, was only slightly correlated and thus poorly predictable by traffic-based variables ( rGIS-based regression models offer a promising approach to assess individual levels of
Van Donkelaar, A.; Martin, R. V.; Brauer, M.; Kahn, R.; Levy, R.; Verduzco, C.; Villeneuve, P.
2010-01-01
Exposure to airborne particles can cause acute or chronic respiratory disease and can exacerbate heart disease, some cancers, and other conditions in susceptible populations. Ground stations that monitor fine particulate matter in the air (smaller than 2.5 microns, called PM2.5) are positioned primarily to observe severe pollution events in areas of high population density; coverage is very limited, even in developed countries, and is not well designed to capture long-term, lower-level exposure that is increasingly linked to chronic health effects. In many parts of the developing world, air quality observation is absent entirely. Instruments aboard NASA Earth Observing System satellites, such as the MODerate resolution Imaging Spectroradiometer (MODIS) and the Multi-angle Imaging SpectroRadiometer (MISR), monitor aerosols from space, providing once daily and about once-weekly coverage, respectively. However, these data are only rarely used for health applications, in part because the can retrieve the amount of aerosols only summed over the entire atmospheric column, rather than focusing just on the near-surface component, in the airspace humans actually breathe. In addition, air quality monitoring often includes detailed analysis of particle chemical composition, impossible from space. In this paper, near-surface aerosol concentrations are derived globally from the total-column aerosol amounts retrieved by MODIS and MISR. Here a computer aerosol simulation is used to determine how much of the satellite-retrieved total column aerosol amount is near the surface. The five-year average (2001-2006) global near-surface aerosol concentration shows that World Health Organization Air Quality standards are exceeded over parts of central and eastern Asia for nearly half the year.
Bullard, Robert L.; Stanier, Charles O.; Ogren, John A.; Sheridan, Patrick J.
2013-05-01
The impact of aerosols on Earth's radiation balance and the associated climate forcing effects of aerosols represent significant uncertainties in assessment reports. The main source of ultrafine aerosols in the atmosphere is the nucleation and subsequent growth of gas phase aerosol precursors into liquid or solid phase particles. Long term records of aerosol number, nucleation event frequency, and vertical profiles of number concentration are rare. The data record from multiagency monitoring assets at Bondville, IL can contribute important information on long term and vertically resolved patterns. Although particle number size distribution data are only occasionally available at Bondville, highly time-resolved particle number concentration data have been measured for nearly twenty years by the NOAA ESRL Global Monitoring Division. Furthermore, vertically-resolved aerosol counts and other aerosol physical parameters are available from more than 300 flights of the NOAA Airborne Aerosol Observatory (AAO). These data sources are used to better understand the seasonal, diurnal, and vertical variation and trends in atmospheric aerosols. The highest peaks in condensation nuclei greater than 14 nm occur during the spring months (May, April) with slightly lower peaks during the fall months (September, October). The diurnal pattern of aerosol number has a midday peak and the timing of the peak has seasonal patterns (earlier during warm months and later during colder months). The seasonal and diurnal patterns of high particle number peaks correspond to seasons and times of day associated with low aerosol mass and surface area. Average vertical profiles show a nearly monotonic decrease with altitude in all months, and with peak magnitudes occurring in the spring and fall. Individual flight tracks show evidence of plumes (i.e., enhanced aerosol number is limited to a small altitude range, is not homogeneous horizontally, or both) as well as periods with enhanced particle number
Chelton, Dudley B.; Schlax, Michael G.
1991-01-01
The sampling error of an arbitrary linear estimate of a time-averaged quantity constructed from a time series of irregularly spaced observations at a fixed located is quantified through a formalism. The method is applied to satellite observations of chlorophyll from the coastal zone color scanner. The two specific linear estimates under consideration are the composite average formed from the simple average of all observations within the averaging period and the optimal estimate formed by minimizing the mean squared error of the temporal average based on all the observations in the time series. The resulting suboptimal estimates are shown to be more accurate than composite averages. Suboptimal estimates are also found to be nearly as accurate as optimal estimates using the correct signal and measurement error variances and correlation functions for realistic ranges of these parameters, which makes it a viable practical alternative to the composite average method generally employed at present.
LENUS (Irish Health Repository)
Dowling, Adam H
2011-06-01
The aim was to investigate the influence of number average molecular weight and concentration of the poly(acrylic) acid (PAA) liquid constituent of a GI restorative on the compressive fracture strength (σ) and modulus (E).
U.S. Environmental Protection Agency — The average concentrations of As, Cd, Cr, Hg, Ni and Pb in n=84 residential soil samples, in Rosia Montana area, analyzed by X-ray fluorescence spectrometry are...
Ukai, Hirohiko; Ohashi, Fumiko; Samoto, Hajime; Fukui, Yoshinari; Okamoto, Satoru; Moriguchi, Jiro; Ezaki, Takafumi; Takada, Shiro; Ikeda, Masayuki
2006-04-01
The present study was initiated to examine the relationship between the workplace concentrations and the estimated highest concentrations in solvent workplaces (SWPs), with special references to enterprise size and types of solvent work. Results of survey conducted in 1010 SWPs in 156 enterprises were taken as a database. Workplace air was sampled at > or = 5 crosses in each SWP following a grid sampling strategy. An additional air was grab-sampled at the site where the worker's exposure was estimated to be highest (estimated highest concentration or EHC). The samples were analyzed for 47 solvents designated by regulation, and solvent concentrations in each sample were summed up by use of additiveness formula. From the workplace concentrations at > or = 5 points, geometric mean and geometric standard deviations were calculated as the representative workplace concentration (RWC) and the indicator of variation in workplace concentration (VWC). Comparison between RWC and EHC in the total of 1010 SWPs showed that EHC was 1.2 (in large enterprises with>300 employees) to 1.7 times [in small to medium (SM) enterprises with enterprises and large enterprises, both RWC and EHC were significantly higher in SM enterprises than in large enterprises. Further comparison by types of solvent work showed that the difference was more marked in printing, surface coating and degreasing/cleaning/wiping SWPs, whereas it was less remarkable in painting SWPs and essentially nil in testing/research laboratories. In conclusion, the present observation as discussed in reference to previous publications suggests that RWC, EHC and the ratio of EHC/WRC varies substantially among different types of solvent work as well as enterprise size, and are typically higher in printing SWPs in SM enterprises.
International Nuclear Information System (INIS)
Tuite, P.; Tuite, K.; O'Kelley, M.; Ely, P.
1991-08-01
This study provides a quantitative framework for bounding unpackaged greater-than-Class C low-level radioactive waste types as a function of concentration averaging. The study defines the three concentration averaging scenarios that lead to base, high, and low volumetric projections; identifies those waste types that could be greater-than-Class C under the high volume, or worst case, concentration averaging scenario; and quantifies the impact of these scenarios on identified waste types relative to the base case scenario. The base volume scenario was assumed to reflect current requirements at the disposal sites as well as the regulatory views. The high volume scenario was assumed to reflect the most conservative criteria as incorporated in some compact host state requirements. The low volume scenario was assumed to reflect the 10 CFR Part 61 criteria as applicable to both shallow land burial facilities and to practices that could be employed to reduce the generation of Class C waste types
International Nuclear Information System (INIS)
Loskiewicz, J.; Olko, P.; Swakon, J.; Bogacz, J.; Janik, M.; Mazur, D.; Mazur, J.
1998-01-01
The variation of radon concentration in some houses in the Krakow region was investigated in order to compare results obtained using various measuring techniques. It is concluded that short-term measurements should last at least 4 days to avoid errors exceeding 30%; that weather parameters and human activity during the measurement should be recorded; that measurements should be repeated several times under various weather conditions; that seasonal variation in the region should be taken into account. (A.K.)
Parkinson, C. L.; Comiso, J. C.; Zwally, H. J.
1987-01-01
A summary data set for four years (mid 70's) of Arctic sea ice conditions is available on magnetic tape. The data include monthly and yearly averaged Nimbus 5 electrically scanning microwave radiometer (ESMR) brightness temperatures, an ice concentration parameter derived from the brightness temperatures, monthly climatological surface air temperatures, and monthly climatological sea level pressures. All data matrices are applied to 293 by 293 grids that cover a polar stereographic map enclosing the 50 deg N latitude circle. The grid size varies from about 32 X 32 km at the poles to about 28 X 28 km at 50 deg N. The ice concentration parameter is calculated assuming that the field of view contains only open water and first-year ice with an ice emissivity of 0.92. To account for the presence of multiyear ice, a nomogram is provided relating the ice concentration parameter, the total ice concentration, and the fraction of the ice cover which is multiyear ice.
Directory of Open Access Journals (Sweden)
М.А. Zemlyanova
2015-03-01
Full Text Available We presented the materials on the verification of the average daily maximum permissible concentration of styrene in the atmospheric air of settlements performed under the results of own in-depth epidemiological studies of children’s population according to the principles of the international risk assessment practice. It was established that children in the age of 4–7 years when exposed to styrene at the level above 1.2 of threshold level value for continuous exposure develop the negative exposure effects in the form of disorders of hormonal regulation, pigmentary exchange, antioxidative activity, cytolysis, immune reactivity and cytogenetic disbalance which contribute to the increased morbidity of diseases of the central nervous system, endocrine system, respiratory organs, digestion and skin. Based on the proved cause-and-effect relationships between the biomarkers of negative effects and styrene concentration in blood it was demonstrated that the benchmark styrene concentration in blood is 0.002 mg/dm3. The justified value complies with and confirms the average daily styrene concentration in the air of settlements at the level of 0.002 mg/m3 accepted in Russia which provides the safety for the health of population (1 threshold level value for continuous exposure.
U.S. Department of Health & Human Services — A list of a variety of averages for each state or territory as well as the national average, including each quality measure, staffing, fine amount and number of...
Van, Tran Thi; Bat, Luu Tam; Nhan, Dang Duc; Quang, Nguyen Hao; Cam, Bui Duy; Hung, Luu Viet
2018-02-16
Radioactivity concentrations of nuclides of the 232 Th and 238 U radioactive chains and 40 K, 90 Sr, 137 Cs, and 239+240 Pu were surveyed for raw and cooked food of the population in the Red River delta region, Vietnam, using α-, γ-spectrometry, and liquid scintillation counting techniques. The concentration of 40 K in the cooked food was the highest compared to those of other radionuclides ranging from (23 ± 5) (rice) to (347 ± 50) Bq kg -1 dw (tofu). The 210 Po concentration in the cooked food ranged from its limit of detection (LOD) of 5 mBq kg -1 dw (rice) to (4.0 ± 1.6) Bq kg -1 dw (marine bivalves). The concentrations of other nuclides of the 232 Th and 238 U chains in the food were low, ranging from LOD of 0.02 Bq kg -1 dw to (1.1 ± 0.3) Bq kg -1 dw. The activity concentrations of 90 Sr, 137 Cs, and 239+240 Pu in the food were minor compared to that of the natural radionuclides. The average annual committed effective dose to adults in the study region was estimated and it ranged from 0.24 to 0.42 mSv a -1 with an average of 0.32 mSv a -1 , out of which rice, leafy vegetable, and tofu contributed up to 16.2%, 24.4%, and 21.3%, respectively. The committed effective doses to adults due to ingestion of regular diet in the Red River delta region, Vietnam are within the range determined in other countries worldwide. This finding suggests that Vietnamese food is safe for human consumption with respect to radiation exposure.
International Nuclear Information System (INIS)
Tuite, P.; Tuite, K.; Harris, G.
1994-09-01
This report evaluates the effects of concentration averaging practices on the disposal of greater-than-Class C low-level radioactive waste (GTCC LLW) generated by the nuclear utility industry and sealed sources. Using estimates of the number of waste components that individually exceed Class C limits, this report calculates the proportion that would be classified as GTCC LLW after applying concentration averaging; this proportion is called the concentration averaging factor. The report uses the guidance outlined in the 1993 Nuclear Regulatory Commission (NRC) draft Branch Technical Position on concentration averaging, as well as waste disposal experience at nuclear utilities, to calculate the concentration averaging factors for nuclear utility wastes. The report uses the 1993 NRC draft Branch Technical Position and the criteria from the Barnwell, South Carolina, LLW disposal site to calculate concentration averaging factors for sealed sources. The report addresses three waste groups: activated metals from light water reactors, process wastes from light-water reactors, and sealed sources. For each waste group, three concentration averaging cases are considered: high, base, and low. The base case, which is the most likely case to occur, assumes using the specific guidance given in the 1993 NRC draft Branch Technical Position on concentration averaging. To project future GTCC LLW generation, each waste category is assigned a concentration averaging factor for the high, base, and low cases
Akita, Yasuyuki; Chen, Jiu-Chiuan; Serre, Marc L
2012-09-01
Geostatistical methods are widely used in estimating long-term exposures for epidemiological studies on air pollution, despite their limited capabilities to handle spatial non-stationarity over large geographic domains and the uncertainty associated with missing monitoring data. We developed a moving-window (MW) Bayesian maximum entropy (BME) method and applied this framework to estimate fine particulate matter (PM(2.5)) yearly average concentrations over the contiguous US. The MW approach accounts for the spatial non-stationarity, while the BME method rigorously processes the uncertainty associated with data missingness in the air-monitoring system. In the cross-validation analyses conducted on a set of randomly selected complete PM(2.5) data in 2003 and on simulated data with different degrees of missing data, we demonstrate that the MW approach alone leads to at least 17.8% reduction in mean square error (MSE) in estimating the yearly PM(2.5). Moreover, the MWBME method further reduces the MSE by 8.4-43.7%, with the proportion of incomplete data increased from 18.3% to 82.0%. The MWBME approach leads to significant reductions in estimation error and thus is recommended for epidemiological studies investigating the effect of long-term exposure to PM(2.5) across large geographical domains with expected spatial non-stationarity.
Akita, Yasuyuki; Chen, Jiu-Chiuan; Serre, Marc L.
2013-01-01
Geostatistical methods are widely used in estimating long-term exposures for air pollution epidemiological studies, despite their limited capabilities to handle spatial non-stationarity over large geographic domains and uncertainty associated with missing monitoring data. We developed a moving-window (MW) Bayesian Maximum Entropy (BME) method and applied this framework to estimate fine particulate matter (PM2.5) yearly average concentrations over the contiguous U.S. The MW approach accounts for the spatial non-stationarity, while the BME method rigorously processes the uncertainty associated with data missingnees in the air monitoring system. In the cross-validation analyses conducted on a set of randomly selected complete PM2.5 data in 2003 and on simulated data with different degrees of missing data, we demonstrate that the MW approach alone leads to at least 17.8% reduction in mean square error (MSE) in estimating the yearly PM2.5. Moreover, the MWBME method further reduces the MSE by 8.4% to 43.7% with the proportion of incomplete data increased from 18.3% to 82.0%. The MWBME approach leads to significant reductions in estimation error and thus is recommended for epidemiological studies investigating the effect of long-term exposure to PM2.5 across large geographical domains with expected spatial non-stationarity. PMID:22739679
International Nuclear Information System (INIS)
Bradley, Paul M.; Journey, Celeste A.; Brigham, Mark E.; Burns, Douglas A.; Button, Daniel T.; Riva-Murray, Karen
2013-01-01
To assess inter-comparability of fluvial mercury (Hg) observations at substantially different scales, Hg concentrations, yields, and bivariate-relations were evaluated at nested-basin locations in the Edisto River, South Carolina and Hudson River, New York. Differences between scales were observed for filtered methylmercury (FMeHg) in the Edisto (attributed to wetland coverage differences) but not in the Hudson. Total mercury (THg) concentrations and bivariate-relationships did not vary substantially with scale in either basin. Combining results of this and a previously published multi-basin study, fish Hg correlated strongly with sampled water FMeHg concentration (ρ = 0.78; p = 0.003) and annual FMeHg basin yield (ρ = 0.66; p = 0.026). Improved correlation (ρ = 0.88; p < 0.0001) was achieved with time-weighted mean annual FMeHg concentrations estimated from basin-specific LOADEST models and daily streamflow. Results suggest reasonable scalability and inter-comparability for different basin sizes if wetland area or related MeHg-source-area metrics are considered. - Highlights: ► National scale mercury assessments integrate small scale study results. ► Basin scale differences and representativeness of fluvial mercury samples are concerns. ► Wetland area, not basin size, predicts inter-basin methylmercury variability. ► Time-weighted methylmercury estimates improve the prediction of mercury in basin fish. - Fluvial methylmercury concentration correlates with wetland area not basin scale and time-weighted estimates better predict basin top predator mercury than discrete sample estimates.
Relative Error Model Reduction via Time-Weighted Balanced Stochastic Singular Perturbation
DEFF Research Database (Denmark)
Tahavori, Maryamsadat; Shaker, Hamid Reza
2012-01-01
A new mixed method for relative error model reduction of linear time invariant (LTI) systems is proposed in this paper. This order reduction technique is mainly based upon time-weighted balanced stochastic model reduction method and singular perturbation model reduction technique. Compared...... by using the concept and properties of the reciprocal systems. The results are further illustrated by two practical numerical examples: a model of CD player and a model of the atmospheric storm track....
Kaye, J. A.; Jackman, C. H.
1986-01-01
Difficulties arise in connection with the verification of multidimensional chemical models of the stratosphere. The present study shows that LIMS data, together with a photochemical equilibrium model, may be used to infer concentrations of a variety of zonally averaged trace Ox, OHx, and NOx species over much of the stratosphere. In the lower stratosphere, where the photochemical equilibrium assumption for HOx species breaks down, inferred concentrations should still be accurate to about a factor of 2 for OH and 2.5 for HO2. The algebraic nature of the considered model makes it possible to see easily to the first order the effect of variation of any model input parameter or its uncertainty on the inferred concontration of the HOx species and their uncertainties.
International Nuclear Information System (INIS)
Chrien, R.E.
1986-10-01
The principles of resonance averaging as applied to neutron capture reactions are described. Several illustrations of resonance averaging to problems of nuclear structure and the distribution of radiative strength in nuclei are provided. 30 refs., 12 figs
Maddison, Ralph; Marsh, Samantha; Foley, Louise; Epstein, Leonard H; Olds, Timothy; Dewes, Ofa; Heke, Ihirangi; Carter, Karen; Jiang, Yannan; Mhurchu, Cliona Ni
2014-09-10
Screen-based activities, such as watching television (TV), playing video games, and using computers, are common sedentary behaviors among young people and have been linked with increased energy intake and overweight. Previous home-based sedentary behaviour interventions have been limited by focusing primarily on the child, small sample sizes, and short follow-up periods. The SWITCH (Screen-Time Weight-loss Intervention Targeting Children at Home) study aimed to determine the effect of a home-based, family-delivered intervention to reduce screen-based sedentary behaviour on body composition, sedentary behaviour, physical activity, and diet over 24 weeks in overweight and obese children. A two-arm, parallel, randomized controlled trial was conducted. Children and their primary caregiver living in Auckland, New Zealand were recruited via schools, community centres, and word of mouth. The intervention, delivered over 20 weeks, consisted of a face-to-face meeting with the parent/caregiver and the child to deliver intervention content, which focused on training and educating them to use a wide range of strategies designed to reduce their child's screen time. Families were given Time Machine TV monitoring devices to assist with allocating screen time, activity packages to promote alternative activities, online support via a website, and monthly newsletters. Control participants were given the intervention material on completion of follow-up. The primary outcome was change in children's BMI z-score from baseline to 24 weeks. Children (n = 251) aged 9-12 years and their primary caregiver were randomized to receive the SWITCH intervention (n = 127) or no intervention (controls; n = 124). There was no significant difference in change of zBMI between the intervention and control groups, although a favorable trend was observed (-0.016; 95% CI: -0.084, 0.051; p = 0.64). There were also no significant differences on secondary outcomes, except for a trend towards
DEFF Research Database (Denmark)
Gramkow, Claus
1999-01-01
In this article two common approaches to averaging rotations are compared to a more advanced approach based on a Riemannian metric. Very offten the barycenter of the quaternions or matrices that represent the rotations are used as an estimate of the mean. These methods neglect that rotations belo...... approximations to the Riemannian metric, and that the subsequent corrections are inherient in the least squares estimation. Keywords: averaging rotations, Riemannian metric, matrix, quaternion......In this article two common approaches to averaging rotations are compared to a more advanced approach based on a Riemannian metric. Very offten the barycenter of the quaternions or matrices that represent the rotations are used as an estimate of the mean. These methods neglect that rotations belong...
International Nuclear Information System (INIS)
Ichiguchi, Katsuji
1998-01-01
A new reduced set of resistive MHD equations is derived by averaging the full MHD equations on specified flux coordinates, which is consistent with 3D equilibria. It is confirmed that the total energy is conserved and the linearized equations for ideal modes are self-adjoint. (author)
Determining average yarding distance.
Roger H. Twito; Charles N. Mann
1979-01-01
Emphasis on environmental and esthetic quality in timber harvesting has brought about increased use of complex boundaries of cutting units and a consequent need for a rapid and accurate method of determining the average yarding distance and area of these units. These values, needed for evaluation of road and landing locations in planning timber harvests, are easily and...
Watson, Jane; Chick, Helen
2012-01-01
This paper analyses the responses of 247 middle school students to items requiring the concept of average in three different contexts: a city's weather reported in maximum daily temperature, the number of children in a family, and the price of houses. The mixed but overall disappointing performance on the six items in the three contexts indicates…
Averaging operations on matrices
Indian Academy of Sciences (India)
2014-07-03
Jul 3, 2014 ... Role of Positive Definite Matrices. • Diffusion Tensor Imaging: 3 × 3 pd matrices model water flow at each voxel of brain scan. • Elasticity: 6 × 6 pd matrices model stress tensors. • Machine Learning: n × n pd matrices occur as kernel matrices. Tanvi Jain. Averaging operations on matrices ...
Directory of Open Access Journals (Sweden)
Patricia Bouyer
2015-09-01
Full Text Available Two-player quantitative zero-sum games provide a natural framework to synthesize controllers with performance guarantees for reactive systems within an uncontrollable environment. Classical settings include mean-payoff games, where the objective is to optimize the long-run average gain per action, and energy games, where the system has to avoid running out of energy. We study average-energy games, where the goal is to optimize the long-run average of the accumulated energy. We show that this objective arises naturally in several applications, and that it yields interesting connections with previous concepts in the literature. We prove that deciding the winner in such games is in NP inter coNP and at least as hard as solving mean-payoff games, and we establish that memoryless strategies suffice to win. We also consider the case where the system has to minimize the average-energy while maintaining the accumulated energy within predefined bounds at all times: this corresponds to operating with a finite-capacity storage for energy. We give results for one-player and two-player games, and establish complexity bounds and memory requirements.
DEFF Research Database (Denmark)
Gramkow, Claus
2001-01-01
In this paper two common approaches to averaging rotations are compared to a more advanced approach based on a Riemannian metric. Very often the barycenter of the quaternions or matrices that represent the rotations are used as an estimate of the mean. These methods neglect that rotations belong ...... approximations to the Riemannian metric, and that the subsequent corrections are inherent in the least squares estimation.......In this paper two common approaches to averaging rotations are compared to a more advanced approach based on a Riemannian metric. Very often the barycenter of the quaternions or matrices that represent the rotations are used as an estimate of the mean. These methods neglect that rotations belong...
Eliazar, Iddo
2018-02-01
The popular perception of statistical distributions is depicted by the iconic bell curve which comprises of a massive bulk of 'middle-class' values, and two thin tails - one of small left-wing values, and one of large right-wing values. The shape of the bell curve is unimodal, and its peak represents both the mode and the mean. Thomas Friedman, the famous New York Times columnist, recently asserted that we have entered a human era in which "Average is Over" . In this paper we present mathematical models for the phenomenon that Friedman highlighted. While the models are derived via different modeling approaches, they share a common foundation. Inherent tipping points cause the models to phase-shift from a 'normal' bell-shape statistical behavior to an 'anomalous' statistical behavior: the unimodal shape changes to an unbounded monotone shape, the mode vanishes, and the mean diverges. Hence: (i) there is an explosion of small values; (ii) large values become super-large; (iii) 'middle-class' values are wiped out, leaving an infinite rift between the small and the super large values; and (iv) "Average is Over" indeed.
DEFF Research Database (Denmark)
Sever, Peter S; Dahlöf, Björn; Poulter, Neil R
2003-01-01
The lowering of cholesterol concentrations in individuals at high risk of cardiovascular disease improves outcome. No study, however, has assessed benefits of cholesterol lowering in the primary prevention of coronary heart disease (CHD) in hypertensive patients who are not conventionally deemed ...
DEFF Research Database (Denmark)
Sever, Peter S; Dahlöf, Björn; Poulter, Neil R
2004-01-01
The lowering of cholesterol concentrations in individuals at high risk of cardiovascular disease improves outcome. No study, however, has assessed benefits of cholesterol lowering in the primary prevention of coronary heart disease (CHD) in hypertensive patients who are not conventionally deemed ...
Average nuclear surface properties
International Nuclear Information System (INIS)
Groote, H. von.
1979-01-01
The definition of the nuclear surface energy is discussed for semi-infinite matter. This definition is extended also for the case that there is a neutron gas instead of vacuum on the one side of the plane surface. The calculations were performed with the Thomas-Fermi Model of Syler and Blanchard. The parameters of the interaction of this model were determined by a least squares fit to experimental masses. The quality of this fit is discussed with respect to nuclear masses and density distributions. The average surface properties were calculated for different particle asymmetry of the nucleon-matter ranging from symmetry beyond the neutron-drip line until the system no longer can maintain the surface boundary and becomes homogeneous. The results of the calculations are incorporated in the nuclear Droplet Model which then was fitted to experimental masses. (orig.)
Americans' Average Radiation Exposure
International Nuclear Information System (INIS)
2000-01-01
We live with radiation every day. We receive radiation exposures from cosmic rays, from outer space, from radon gas, and from other naturally radioactive elements in the earth. This is called natural background radiation. It includes the radiation we get from plants, animals, and from our own bodies. We also are exposed to man-made sources of radiation, including medical and dental treatments, television sets and emission from coal-fired power plants. Generally, radiation exposures from man-made sources are only a fraction of those received from natural sources. One exception is high exposures used by doctors to treat cancer patients. Each year in the United States, the average dose to people from natural and man-made radiation sources is about 360 millirem. A millirem is an extremely tiny amount of energy absorbed by tissues in the body
International Nuclear Information System (INIS)
Balint, A.B.; Viljoen, J.
1988-01-01
An experimental personal alpha dosimetry program for monitoring exposures of uranium mining facility workers in Canada has been completed. All licenced operating mining facilities were participating. Dosimetry techniques, description of dosimeters used by licences, performance and problems associated with the implementation of the programme as well as technical and administrative advantages and difficulties experienced are discussed. Area monitoring-time weighting methods used and results obtained to determine individual radon and thoron daughter exposure and exposure results generated by using dosimeters are assessed and compared
Energy Technology Data Exchange (ETDEWEB)
Pujol, R.; Moia, A.; Martinez, V.
2008-07-01
Three different geometries of a fixed solar mirror concentrator and tracking absorber have been analyzed for medium temperature: FSMC flat mirrors, FSMC parabolic mirrors and only one parabolic mirror OPMSC. These designs can track the sun by moving the receiver around a static reflector in a circular path. A forward ray tracing procedure was implemented by the authors to analyze the influence of the collector parameters on optical efficiency. Various combinations of D/W ratios and geometric concentration ratios C were studied. The analysis showed that as D/W increases the efficiency increases well. Annual efficiencies of a 40% can be reached, in front of 35 % estimated with commercial evacuated tubes at 120 degree centigrade. (Author)
Influence of dispatching rules on average production lead time for multi-stage production systems.
Hübl, Alexander; Jodlbauer, Herbert; Altendorfer, Klaus
2013-08-01
In this paper the influence of different dispatching rules on the average production lead time is investigated. Two theorems based on covariance between processing time and production lead time are formulated and proved theoretically. Theorem 1 links the average production lead time to the "processing time weighted production lead time" for the multi-stage production systems analytically. The influence of different dispatching rules on average lead time, which is well known from simulation and empirical studies, can be proved theoretically in Theorem 2 for a single stage production system. A simulation study is conducted to gain more insight into the influence of dispatching rules on average production lead time in a multi-stage production system. We find that the "processing time weighted average production lead time" for a multi-stage production system is not invariant of the applied dispatching rule and can be used as a dispatching rule independent indicator for single-stage production systems.
The difference between alternative averages
Directory of Open Access Journals (Sweden)
James Vaupel
2012-09-01
Full Text Available BACKGROUND Demographers have long been interested in how compositional change, e.g., change in age structure, affects population averages. OBJECTIVE We want to deepen understanding of how compositional change affects population averages. RESULTS The difference between two averages of a variable, calculated using alternative weighting functions, equals the covariance between the variable and the ratio of the weighting functions, divided by the average of the ratio. We compare weighted and unweighted averages and also provide examples of use of the relationship in analyses of fertility and mortality. COMMENTS Other uses of covariances in formal demography are worth exploring.
How to average logarithmic retrievals?
Directory of Open Access Journals (Sweden)
B. Funke
2012-04-01
Full Text Available Calculation of mean trace gas contributions from profiles obtained by retrievals of the logarithm of the abundance rather than retrievals of the abundance itself are prone to biases. By means of a system simulator, biases of linear versus logarithmic averaging were evaluated for both maximum likelihood and maximum a priori retrievals, for various signal to noise ratios and atmospheric variabilities. These biases can easily reach ten percent or more. As a rule of thumb we found for maximum likelihood retrievals that linear averaging better represents the true mean value in cases of large local natural variability and high signal to noise ratios, while for small local natural variability logarithmic averaging often is superior. In the case of maximum a posteriori retrievals, the mean is dominated by the a priori information used in the retrievals and the method of averaging is of minor concern. For larger natural variabilities, the appropriateness of the one or the other method of averaging depends on the particular case because the various biasing mechanisms partly compensate in an unpredictable manner. This complication arises mainly because of the fact that in logarithmic retrievals the weight of the prior information depends on abundance of the gas itself. No simple rule was found on which kind of averaging is superior, and instead of suggesting simple recipes we cannot do much more than to create awareness of the traps related with averaging of mixing ratios obtained from logarithmic retrievals.
Lagrangian averaging with geodesic mean.
Oliver, Marcel
2017-11-01
This paper revisits the derivation of the Lagrangian averaged Euler (LAE), or Euler- α equations in the light of an intrinsic definition of the averaged flow map as the geodesic mean on the volume-preserving diffeomorphism group. Under the additional assumption that first-order fluctuations are statistically isotropic and transported by the mean flow as a vector field, averaging of the kinetic energy Lagrangian of an ideal fluid yields the LAE Lagrangian. The derivation presented here assumes a Euclidean spatial domain without boundaries.
Averaging in spherically symmetric cosmology
International Nuclear Information System (INIS)
Coley, A. A.; Pelavas, N.
2007-01-01
The averaging problem in cosmology is of fundamental importance. When applied to study cosmological evolution, the theory of macroscopic gravity (MG) can be regarded as a long-distance modification of general relativity. In the MG approach to the averaging problem in cosmology, the Einstein field equations on cosmological scales are modified by appropriate gravitational correlation terms. We study the averaging problem within the class of spherically symmetric cosmological models. That is, we shall take the microscopic equations and effect the averaging procedure to determine the precise form of the correlation tensor in this case. In particular, by working in volume-preserving coordinates, we calculate the form of the correlation tensor under some reasonable assumptions on the form for the inhomogeneous gravitational field and matter distribution. We find that the correlation tensor in a Friedmann-Lemaitre-Robertson-Walker (FLRW) background must be of the form of a spatial curvature. Inhomogeneities and spatial averaging, through this spatial curvature correction term, can have a very significant dynamical effect on the dynamics of the Universe and cosmological observations; in particular, we discuss whether spatial averaging might lead to a more conservative explanation of the observed acceleration of the Universe (without the introduction of exotic dark matter fields). We also find that the correlation tensor for a non-FLRW background can be interpreted as the sum of a spatial curvature and an anisotropic fluid. This may lead to interesting effects of averaging on astrophysical scales. We also discuss the results of averaging an inhomogeneous Lemaitre-Tolman-Bondi solution as well as calculations of linear perturbations (that is, the backreaction) in an FLRW background, which support the main conclusions of the analysis
Averaging models: parameters estimation with the R-Average procedure
Directory of Open Access Journals (Sweden)
S. Noventa
2010-01-01
Full Text Available The Functional Measurement approach, proposed within the theoretical framework of Information Integration Theory (Anderson, 1981, 1982, can be a useful multi-attribute analysis tool. Compared to the majority of statistical models, the averaging model can account for interaction effects without adding complexity. The R-Average method (Vidotto & Vicentini, 2007 can be used to estimate the parameters of these models. By the use of multiple information criteria in the model selection procedure, R-Average allows for the identification of the best subset of parameters that account for the data. After a review of the general method, we present an implementation of the procedure in the framework of R-project, followed by some experiments using a Monte Carlo method.
Evaluations of average level spacings
International Nuclear Information System (INIS)
Liou, H.I.
1980-01-01
The average level spacing for highly excited nuclei is a key parameter in cross section formulas based on statistical nuclear models, and also plays an important role in determining many physics quantities. Various methods to evaluate average level spacings are reviewed. Because of the finite experimental resolution, to detect a complete sequence of levels without mixing other parities is extremely difficult, if not totally impossible. Most methods derive the average level spacings by applying a fit, with different degrees of generality, to the truncated Porter-Thomas distribution for reduced neutron widths. A method that tests both distributions of level widths and positions is discussed extensivey with an example of 168 Er data. 19 figures, 2 tables
Ergodic averages via dominating processes
DEFF Research Database (Denmark)
Møller, Jesper; Mengersen, Kerrie
2006-01-01
We show how the mean of a monotone function (defined on a state space equipped with a partial ordering) can be estimated, using ergodic averages calculated from upper and lower dominating processes of a stationary irreducible Markov chain. In particular, we do not need to simulate the stationary...... Markov chain and we eliminate the problem of whether an appropriate burn-in is determined or not. Moreover, when a central limit theorem applies, we show how confidence intervals for the mean can be estimated by bounding the asymptotic variance of the ergodic average based on the equilibrium chain....
Directory of Open Access Journals (Sweden)
Seyedtaghi Mirmohammadi
2017-08-01
Full Text Available Background: Manganese (Mn used as raw material for melting process in the ferrous foundry is considered as hazardous neurotoxic substance because it accumulates in the central nervous system and may cause neurological disorders. The furnace-men and melting department workers are potentially exposed to manganese particles or fume in the workplace. The objective of the research has been to investigate the sources and levels of manganese exposure in the foundry by correlation of blood-manganese (B-Mn and air-manganese (air-Mn measurement. Material and Methods: Air-Mn and Mn of blood serum were measured involving workers who worked in a big-sized foundry during 1 year. The standard method of the Occupational Safety and Health Administration (OSHA ID-121 was used for air and blood assessment and atomic absorption spectroscopy (AAS was carried out for air and blood sample analysis. Results: The air sampling results have revealed that there is a high exposure to manganese (4.5 mg/m3 in the workplace as compared to the National Institute for Occupational Safety and Health’s (NIOSH time weighted average (the reference time-weighted average (TWA = 1 mg/m3. The average blood serum Mn concentration was 2.745 μg/l for subjects working for shorter than 3 months and 274.85 μg/l for subjects working 3–12 months. Conclusions: Against the research hypothesis there was no correlation between the air-Mn concentration and the B-Mn (serum level of manganese in the serum of the exposed subjects. It may be due to short time of air sampling of manganese airborne particles, and a real-time monitoring of airborne manganese particles is suggested for any future study. Med Pr 2017;68(4:449–458
High average power supercontinuum sources
Indian Academy of Sciences (India)
The physical mechanisms and basic experimental techniques for the creation of high average spectral power supercontinuum sources is briefly reviewed. We focus on the use of high-power ytterbium-doped fibre lasers as pump sources, and the use of highly nonlinear photonic crystal fibres as the nonlinear medium.
When good = better than average
Directory of Open Access Journals (Sweden)
Don A. Moore
2007-10-01
Full Text Available People report themselves to be above average on simple tasks and below average on difficult tasks. This paper proposes an explanation for this effect that is simpler than prior explanations. The new explanation is that people conflate relative with absolute evaluation, especially on subjective measures. The paper then presents a series of four studies that test this conflation explanation. These tests distinguish conflation from other explanations, such as differential weighting and selecting the wrong referent. The results suggest that conflation occurs at the response stage during which people attempt to disambiguate subjective response scales in order to choose an answer. This is because conflation has little effect on objective measures, which would be equally affected if the conflation occurred at encoding.
Autoregressive Moving Average Graph Filtering
Isufi, Elvin; Loukas, Andreas; Simonetto, Andrea; Leus, Geert
2016-01-01
One of the cornerstones of the field of signal processing on graphs are graph filters, direct analogues of classical filters, but intended for signals defined on graphs. This work brings forth new insights on the distributed graph filtering problem. We design a family of autoregressive moving average (ARMA) recursions, which (i) are able to approximate any desired graph frequency response, and (ii) give exact solutions for tasks such as graph signal denoising and interpolation. The design phi...
Averaging Robertson-Walker cosmologies
International Nuclear Information System (INIS)
Brown, Iain A.; Robbers, Georg; Behrend, Juliane
2009-01-01
The cosmological backreaction arises when one directly averages the Einstein equations to recover an effective Robertson-Walker cosmology, rather than assuming a background a priori. While usually discussed in the context of dark energy, strictly speaking any cosmological model should be recovered from such a procedure. We apply the scalar spatial averaging formalism for the first time to linear Robertson-Walker universes containing matter, radiation and dark energy. The formalism employed is general and incorporates systems of multiple fluids with ease, allowing us to consider quantitatively the universe from deep radiation domination up to the present day in a natural, unified manner. Employing modified Boltzmann codes we evaluate numerically the discrepancies between the assumed and the averaged behaviour arising from the quadratic terms, finding the largest deviations for an Einstein-de Sitter universe, increasing rapidly with Hubble rate to a 0.01% effect for h = 0.701. For the ΛCDM concordance model, the backreaction is of the order of Ω eff 0 ≈ 4 × 10 −6 , with those for dark energy models being within a factor of two or three. The impacts at recombination are of the order of 10 −8 and those in deep radiation domination asymptote to a constant value. While the effective equations of state of the backreactions in Einstein-de Sitter, concordance and quintessence models are generally dust-like, a backreaction with an equation of state w eff < −1/3 can be found for strongly phantom models
Directory of Open Access Journals (Sweden)
Tsai Midi
2011-06-01
Full Text Available Abstract Background Approximately one third of New Zealand children and young people are overweight or obese. A similar proportion (33% do not meet recommendations for physical activity, and 70% do not meet recommendations for screen time. Increased time being sedentary is positively associated with being overweight. There are few family-based interventions aimed at reducing sedentary behavior in children. The aim of this trial is to determine the effects of a 24 week home-based, family oriented intervention to reduce sedentary screen time on children's body composition, sedentary behavior, physical activity, and diet. Methods/Design The study design is a pragmatic two-arm parallel randomized controlled trial. Two hundred and seventy overweight children aged 9-12 years and primary caregivers are being recruited. Participants are randomized to intervention (family-based screen time intervention or control (no change. At the end of the study, the control group is offered the intervention content. Data collection is undertaken at baseline and 24 weeks. The primary trial outcome is child body mass index (BMI and standardized body mass index (zBMI. Secondary outcomes are change from baseline to 24 weeks in child percentage body fat; waist circumference; self-reported average daily time spent in physical and sedentary activities; dietary intake; and enjoyment of physical activity and sedentary behavior. Secondary outcomes for the primary caregiver include change in BMI and self-reported physical activity. Discussion This study provides an excellent example of a theory-based, pragmatic, community-based trial targeting sedentary behavior in overweight children. The study has been specifically designed to allow for estimation of the consistency of effects on body composition for Māori (indigenous, Pacific and non-Māori/non-Pacific ethnic groups. If effective, this intervention is imminently scalable and could be integrated within existing weight
Topological quantization of ensemble averages
International Nuclear Information System (INIS)
Prodan, Emil
2009-01-01
We define the current of a quantum observable and, under well-defined conditions, we connect its ensemble average to the index of a Fredholm operator. The present work builds on a formalism developed by Kellendonk and Schulz-Baldes (2004 J. Funct. Anal. 209 388) to study the quantization of edge currents for continuous magnetic Schroedinger operators. The generalization given here may be a useful tool to scientists looking for novel manifestations of the topological quantization. As a new application, we show that the differential conductance of atomic wires is given by the index of a certain operator. We also comment on how the formalism can be used to probe the existence of edge states
Flexible time domain averaging technique
Zhao, Ming; Lin, Jing; Lei, Yaguo; Wang, Xiufeng
2013-09-01
Time domain averaging(TDA) is essentially a comb filter, it cannot extract the specified harmonics which may be caused by some faults, such as gear eccentric. Meanwhile, TDA always suffers from period cutting error(PCE) to different extent. Several improved TDA methods have been proposed, however they cannot completely eliminate the waveform reconstruction error caused by PCE. In order to overcome the shortcomings of conventional methods, a flexible time domain averaging(FTDA) technique is established, which adapts to the analyzed signal through adjusting each harmonic of the comb filter. In this technique, the explicit form of FTDA is first constructed by frequency domain sampling. Subsequently, chirp Z-transform(CZT) is employed in the algorithm of FTDA, which can improve the calculating efficiency significantly. Since the signal is reconstructed in the continuous time domain, there is no PCE in the FTDA. To validate the effectiveness of FTDA in the signal de-noising, interpolation and harmonic reconstruction, a simulated multi-components periodic signal that corrupted by noise is processed by FTDA. The simulation results show that the FTDA is capable of recovering the periodic components from the background noise effectively. Moreover, it can improve the signal-to-noise ratio by 7.9 dB compared with conventional ones. Experiments are also carried out on gearbox test rigs with chipped tooth and eccentricity gear, respectively. It is shown that the FTDA can identify the direction and severity of the eccentricity gear, and further enhances the amplitudes of impulses by 35%. The proposed technique not only solves the problem of PCE, but also provides a useful tool for the fault symptom extraction of rotating machinery.
The average Indian female nose.
Patil, Surendra B; Kale, Satish M; Jaiswal, Sumeet; Khare, Nishant; Math, Mahantesh
2011-12-01
This study aimed to delineate the anthropometric measurements of the noses of young women of an Indian population and to compare them with the published ideals and average measurements for white women. This anthropometric survey included a volunteer sample of 100 young Indian women ages 18 to 35 years with Indian parents and no history of previous surgery or trauma to the nose. Standardized frontal, lateral, oblique, and basal photographs of the subjects' noses were taken, and 12 standard anthropometric measurements of the nose were determined. The results were compared with published standards for North American white women. In addition, nine nasal indices were calculated and compared with the standards for North American white women. The nose of Indian women differs significantly from the white nose. All the nasal measurements for the Indian women were found to be significantly different from those for North American white women. Seven of the nine nasal indices also differed significantly. Anthropometric analysis suggests differences between the Indian female nose and the North American white nose. Thus, a single aesthetic ideal is inadequate. Noses of Indian women are smaller and wider, with a less projected and rounded tip than the noses of white women. This study established the nasal anthropometric norms for nasal parameters, which will serve as a guide for cosmetic and reconstructive surgery in Indian women.
New device for time-averaged measurement of volatile organic compounds (VOCs)
Energy Technology Data Exchange (ETDEWEB)
Santiago Sánchez, Noemí; Tejada Alarcón, Sergio; Tortajada Santonja, Rafael; Llorca-Pórcel, Julio, E-mail: julio.llorca@aqualogy.net
2014-07-01
through a glass cell containing adsorbent material where the VOCs are retained. The adsorbent used, made in LABAQUA, is a mixture of alginic acid and activated carbon. Due to its high permeability it allows the passage and retention of THMs in a suitable way, thus solving many of the problems of other common adsorbents. Also, to avoid degradation of the adsorbent, it is wrapped in a low density polyethylene (LDPE) membrane. After a sampling period of between 1 and 14 days, the adsorbent is collected and analyzed in the laboratory to quantify the VOC average concentration. This device resolves some of the limitations of the classical sampling system (spot samples), since we will take into account the fluctuations in the concentration of VOCs by averaging the same over time. This study presents the results obtained by the device for quantifying the VOCs legislated in the Directive 2000/60/EC. We present the validation of linearity over time and the limits of quantification, as well as the results of sample rate (Rs) obtained for each compound. The results demonstrate the high robustness and high sensitivity of the device. In addition the system has been validated in real waste water samples, comparing the results obtained with this device with the values of classical spot sampling, obtaining excellent results. - Highlights: • Device to determine time weighted average concentrations of VOCs in water • This device is presented as an important alternative to spot sampling. • Very low LOD values of VOCs are obtained over 7 days of sampling. • Optimization, validation and application of the device in waters.
DEFF Research Database (Denmark)
Vendelboe, Anders Lindblad; de Jonge, Hubert; Møldrup, Per
2012-01-01
Glyphosate is one of the world’s most extensively used weed control agents. Glyphosate, and its metabolite aminomethylphosphonic acid (AMPA), are suspected to be hazardous to human health and the aquatic environment. In Denmark, the extensive use has resulted in an increasing number of occurrences......Cell, will decrease the workload and number of samples freeing up funds for larger monitoring programs. When installed in a well the SorbiCell will continuously sample the water giving either a flux-weighed or time-weighted average measurement of the glyphosate/AMPA concentration throughout the sampling period....... It may therefore be possible to measure lower concentrations as the glyphosate/AMPA sorbed in the SorbiCell is an accumulated measurement. Also, glyphosate/AMPA associated with sudden flush events will be detected by the SorbiCells, while such events may pass between two consecutive grab samples...
Averaging of nonlinearity-managed pulses
International Nuclear Information System (INIS)
Zharnitsky, Vadim; Pelinovsky, Dmitry
2005-01-01
We consider the nonlinear Schroedinger equation with the nonlinearity management which describes Bose-Einstein condensates under Feshbach resonance. By using an averaging theory, we derive the Hamiltonian averaged equation and compare it with other averaging methods developed for this problem. The averaged equation is used for analytical approximations of nonlinearity-managed solitons
The average size of ordered binary subgraphs
van Leeuwen, J.; Hartel, Pieter H.
To analyse the demands made on the garbage collector in a graph reduction system, the change in size of an average graph is studied when an arbitrary edge is removed. In ordered binary trees the average number of deleted nodes as a result of cutting a single edge is equal to the average size of a
Determination of average activating thermal neutron flux in bulk samples
International Nuclear Information System (INIS)
Doczi, R.; Csikai, J.; Doczi, R.; Csikai, J.; Hassan, F. M.; Ali, M.A.
2004-01-01
A previous method used for the determination of the average neutron flux within bulky samples has been applied for the measurements of hydrogen contents of different samples. An analytical function is given for the description of the correlation between the activity of Dy foils and the hydrogen concentrations. Results obtained by the activation and the thermal neutron reflection methods are compared
Averaging for solitons with nonlinearity management
International Nuclear Information System (INIS)
Pelinovsky, D.E.; Kevrekidis, P.G.; Frantzeskakis, D.J.
2003-01-01
We develop an averaging method for solitons of the nonlinear Schroedinger equation with a periodically varying nonlinearity coefficient, which is used to effectively describe solitons in Bose-Einstein condensates, in the context of the recently proposed technique of Feshbach resonance management. Using the derived local averaged equation, we study matter-wave bright and dark solitons and demonstrate a very good agreement between solutions of the averaged and full equations
DSCOVR Magnetometer Level 2 One Minute Averages
National Oceanic and Atmospheric Administration, Department of Commerce — Interplanetary magnetic field observations collected from magnetometer on DSCOVR satellite - 1-minute average of Level 1 data
DSCOVR Magnetometer Level 2 One Second Averages
National Oceanic and Atmospheric Administration, Department of Commerce — Interplanetary magnetic field observations collected from magnetometer on DSCOVR satellite - 1-second average of Level 1 data
Spacetime averaging of exotic singularity universes
International Nuclear Information System (INIS)
Dabrowski, Mariusz P.
2011-01-01
Taking a spacetime average as a measure of the strength of singularities we show that big-rips (type I) are stronger than big-bangs. The former have infinite spacetime averages while the latter have them equal to zero. The sudden future singularities (type II) and w-singularities (type V) have finite spacetime averages. The finite scale factor (type III) singularities for some values of the parameters may have an infinite average and in that sense they may be considered stronger than big-bangs.
NOAA Average Annual Salinity (3-Zone)
California Natural Resource Agency — The 3-Zone Average Annual Salinity Digital Geography is a digital spatial framework developed using geographic information system (GIS) technology. These salinity...
Iglesias, Verónica; Erazo, Marcia; Droppelmann, Andrea; Steenland, Kyle; Aceituno, Paulina; Orellana, Cecilia; Acuña, Marisol; Peruga, Armando; Breysse, Patrick N.; Navas-Acien, Ana
2015-01-01
Objective To evaluate the relative contribution of occupational vs. non-occupational secondhand tobacco smoke exposure to overall hair nicotine concentrations in non-smoking bar and restaurant employees. Method We recruited 76 non-smoking employees from venues that allowed smoking (n = 9), had mixed policies (smoking and non-smoking areas, n = 13) or were smoke-free (n = 2) between April and August 2008 in Santiago, Chile. Employees used personal air nicotine samplers during working and non-working hours for a 24-h period to assess occupational vs. non-occupational secondhand tobacco smoke exposure and hair nicotine concentrations to assess overall secondhand tobacco smoke exposure. Results Median hair nicotine concentrations were 1.5 ng/mg, interquartile range (IQR) 0.7 to 5.2 ng/mg. Time weighted average personal air nicotine concentrations were higher during working hours (median 9.7, IQR 3.3-25.4 μg/m3) compared to non-working hours (1.7, 1.0-3.1 μg/m3). Hair nicotine concentration was best predicted by personal air nicotine concentration at working hours. After adjustment, a 2-fold increase in personal air nicotine concentration in working hours was associated with a 42% increase in hair nicotine concentration (95% confidence interval 14-70%). Hair nicotine concentration was not associated with personal air nicotine concentration during non-working hours (non-occupational exposure). Conclusions Personal air nicotine concentration at working hours was the major determinant of hair nicotine concentrations in non-smoking employees from Santiago, Chile. Secondhand tobacco smoke exposure during working hours is a health hazard for hospitality employees working in venues where smoking is allowed. PMID:24813578
Lateral dispersion coefficients as functions of averaging time
International Nuclear Information System (INIS)
Sheih, C.M.
1980-01-01
Plume dispersion coefficients are discussed in terms of single-particle and relative diffusion, and are investigated as functions of averaging time. To demonstrate the effects of averaging time on the relative importance of various dispersion processes, and observed lateral wind velocity spectrum is used to compute the lateral dispersion coefficients of total, single-particle and relative diffusion for various averaging times and plume travel times. The results indicate that for a 1 h averaging time the dispersion coefficient of a plume can be approximated by single-particle diffusion alone for travel times <250 s and by relative diffusion for longer travel times. Furthermore, it is shown that the power-law formula suggested by Turner for relating pollutant concentrations for other averaging times to the corresponding 15 min average is applicable to the present example only when the averaging time is less than 200 s and the tral time smaller than about 300 s. Since the turbulence spectrum used in the analysis is an observed one, it is hoped that the results could represent many conditions encountered in the atmosphere. However, as the results depend on the form of turbulence spectrum, the calculations are not for deriving a set of specific criteria but for demonstrating the need in discriminating various processes in studies of plume dispersion
Improving consensus structure by eliminating averaging artifacts
Directory of Open Access Journals (Sweden)
KC Dukka B
2009-03-01
Full Text Available Abstract Background Common structural biology methods (i.e., NMR and molecular dynamics often produce ensembles of molecular structures. Consequently, averaging of 3D coordinates of molecular structures (proteins and RNA is a frequent approach to obtain a consensus structure that is representative of the ensemble. However, when the structures are averaged, artifacts can result in unrealistic local geometries, including unphysical bond lengths and angles. Results Herein, we describe a method to derive representative structures while limiting the number of artifacts. Our approach is based on a Monte Carlo simulation technique that drives a starting structure (an extended or a 'close-by' structure towards the 'averaged structure' using a harmonic pseudo energy function. To assess the performance of the algorithm, we applied our approach to Cα models of 1364 proteins generated by the TASSER structure prediction algorithm. The average RMSD of the refined model from the native structure for the set becomes worse by a mere 0.08 Å compared to the average RMSD of the averaged structures from the native structure (3.28 Å for refined structures and 3.36 A for the averaged structures. However, the percentage of atoms involved in clashes is greatly reduced (from 63% to 1%; in fact, the majority of the refined proteins had zero clashes. Moreover, a small number (38 of refined structures resulted in lower RMSD to the native protein versus the averaged structure. Finally, compared to PULCHRA 1, our approach produces representative structure of similar RMSD quality, but with much fewer clashes. Conclusion The benchmarking results demonstrate that our approach for removing averaging artifacts can be very beneficial for the structural biology community. Furthermore, the same approach can be applied to almost any problem where averaging of 3D coordinates is performed. Namely, structure averaging is also commonly performed in RNA secondary prediction 2, which
40 CFR 76.11 - Emissions averaging.
2010-07-01
... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Emissions averaging. 76.11 Section 76.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.11 Emissions averaging. (a) General...
Determinants of College Grade Point Averages
Bailey, Paul Dean
2012-01-01
Chapter 2: The Role of Class Difficulty in College Grade Point Averages. Grade Point Averages (GPAs) are widely used as a measure of college students' ability. Low GPAs can remove a students from eligibility for scholarships, and even continued enrollment at a university. However, GPAs are determined not only by student ability but also by the…
Role of spatial averaging in multicellular gradient sensing.
Smith, Tyler; Fancher, Sean; Levchenko, Andre; Nemenman, Ilya; Mugler, Andrew
2016-05-20
Gradient sensing underlies important biological processes including morphogenesis, polarization, and cell migration. The precision of gradient sensing increases with the length of a detector (a cell or group of cells) in the gradient direction, since a longer detector spans a larger range of concentration values. Intuition from studies of concentration sensing suggests that precision should also increase with detector length in the direction transverse to the gradient, since then spatial averaging should reduce the noise. However, here we show that, unlike for concentration sensing, the precision of gradient sensing decreases with transverse length for the simplest gradient sensing model, local excitation-global inhibition. The reason is that gradient sensing ultimately relies on a subtraction of measured concentration values. While spatial averaging indeed reduces the noise in these measurements, which increases precision, it also reduces the covariance between the measurements, which results in the net decrease in precision. We demonstrate how a recently introduced gradient sensing mechanism, regional excitation-global inhibition (REGI), overcomes this effect and recovers the benefit of transverse averaging. Using a REGI-based model, we compute the optimal two- and three-dimensional detector shapes, and argue that they are consistent with the shapes of naturally occurring gradient-sensing cell populations.
Computation of the bounce-average code
International Nuclear Information System (INIS)
Cutler, T.A.; Pearlstein, L.D.; Rensink, M.E.
1977-01-01
The bounce-average computer code simulates the two-dimensional velocity transport of ions in a mirror machine. The code evaluates and bounce-averages the collision operator and sources along the field line. A self-consistent equilibrium magnetic field is also computed using the long-thin approximation. Optionally included are terms that maintain μ, J invariance as the magnetic field changes in time. The assumptions and analysis that form the foundation of the bounce-average code are described. When references can be cited, the required results are merely stated and explained briefly. A listing of the code is appended
Rotational averaging of multiphoton absorption cross sections
Energy Technology Data Exchange (ETDEWEB)
Friese, Daniel H., E-mail: daniel.h.friese@uit.no; Beerepoot, Maarten T. P.; Ruud, Kenneth [Centre for Theoretical and Computational Chemistry, University of Tromsø — The Arctic University of Norway, N-9037 Tromsø (Norway)
2014-11-28
Rotational averaging of tensors is a crucial step in the calculation of molecular properties in isotropic media. We present a scheme for the rotational averaging of multiphoton absorption cross sections. We extend existing literature on rotational averaging to even-rank tensors of arbitrary order and derive equations that require only the number of photons as input. In particular, we derive the first explicit expressions for the rotational average of five-, six-, and seven-photon absorption cross sections. This work is one of the required steps in making the calculation of these higher-order absorption properties possible. The results can be applied to any even-rank tensor provided linearly polarized light is used.
Sea Surface Temperature Average_SST_Master
National Oceanic and Atmospheric Administration, Department of Commerce — Sea surface temperature collected via satellite imagery from http://www.esrl.noaa.gov/psd/data/gridded/data.noaa.ersst.html and averaged for each region using ArcGIS...
Trajectory averaging for stochastic approximation MCMC algorithms
Liang, Faming
2010-01-01
to the stochastic approximation Monte Carlo algorithm [Liang, Liu and Carroll J. Amer. Statist. Assoc. 102 (2007) 305-320]. The application of the trajectory averaging estimator to other stochastic approximationMCMC algorithms, for example, a stochastic
Should the average tax rate be marginalized?
Czech Academy of Sciences Publication Activity Database
Feldman, N. E.; Katuščák, Peter
-, č. 304 (2006), s. 1-65 ISSN 1211-3298 Institutional research plan: CEZ:MSM0021620846 Keywords : tax * labor supply * average tax Subject RIV: AH - Economics http://www.cerge-ei.cz/pdf/wp/Wp304.pdf
A practical guide to averaging functions
Beliakov, Gleb; Calvo Sánchez, Tomasa
2016-01-01
This book offers an easy-to-use and practice-oriented reference guide to mathematical averages. It presents different ways of aggregating input values given on a numerical scale, and of choosing and/or constructing aggregating functions for specific applications. Building on a previous monograph by Beliakov et al. published by Springer in 2007, it outlines new aggregation methods developed in the interim, with a special focus on the topic of averaging aggregation functions. It examines recent advances in the field, such as aggregation on lattices, penalty-based aggregation and weakly monotone averaging, and extends many of the already existing methods, such as: ordered weighted averaging (OWA), fuzzy integrals and mixture functions. A substantial mathematical background is not called for, as all the relevant mathematical notions are explained here and reported on together with a wealth of graphical illustrations of distinct families of aggregation functions. The authors mainly focus on practical applications ...
MN Temperature Average (1961-1990) - Line
Minnesota Department of Natural Resources — This data set depicts 30-year averages (1961-1990) of monthly and annual temperatures for Minnesota. Isolines and regions were created using kriging and...
MN Temperature Average (1961-1990) - Polygon
Minnesota Department of Natural Resources — This data set depicts 30-year averages (1961-1990) of monthly and annual temperatures for Minnesota. Isolines and regions were created using kriging and...
Average Bandwidth Allocation Model of WFQ
Directory of Open Access Journals (Sweden)
Tomáš Balogh
2012-01-01
Full Text Available We present a new iterative method for the calculation of average bandwidth assignment to traffic flows using a WFQ scheduler in IP based NGN networks. The bandwidth assignment calculation is based on the link speed, assigned weights, arrival rate, and average packet length or input rate of the traffic flows. We prove the model outcome with examples and simulation results using NS2 simulator.
Nonequilibrium statistical averages and thermo field dynamics
International Nuclear Information System (INIS)
Marinaro, A.; Scarpetta, Q.
1984-01-01
An extension of thermo field dynamics is proposed, which permits the computation of nonequilibrium statistical averages. The Brownian motion of a quantum oscillator is treated as an example. In conclusion it is pointed out that the procedure proposed to computation of time-dependent statistical average gives the correct two-point Green function for the damped oscillator. A simple extension can be used to compute two-point Green functions of free particles
An approximate analytical approach to resampling averages
DEFF Research Database (Denmark)
Malzahn, Dorthe; Opper, M.
2004-01-01
Using a novel reformulation, we develop a framework to compute approximate resampling data averages analytically. The method avoids multiple retraining of statistical models on the samples. Our approach uses a combination of the replica "trick" of statistical physics and the TAP approach for appr...... for approximate Bayesian inference. We demonstrate our approach on regression with Gaussian processes. A comparison with averages obtained by Monte-Carlo sampling shows that our method achieves good accuracy....
Airborne asbestos concentrations associated with heavy equipment brake removal.
Madl, A K; Gaffney, S H; Balzer, J L; Paustenbach, D J
2009-11-01
Asbestos-containing brake linings were used in heavy-duty construction equipment such as tractors, backhoes, and bulldozers prior to the 1980s. While several published studies have evaluated exposures to mechanics during brake repair work, most have focused on automobiles and light trucks, not on heavy agricultural or construction vehicles. The purpose of this study is to characterize the airborne concentration of asbestos to workers and bystanders from brake wear debris during brake removal from 12 loader/backhoes and tractors manufactured between 1960 and 1980. Asbestos content in brake lining (average 20% chrysotile by polarized light microscopy) and brake wear debris [average 0.49% chrysotile by transmission electron microscopy (TEM)] was also quantified. Breathing zone samples on the lapel of mechanics (n = 44) and area samples at bystander (n = 34), remote (n = 22), and ambient (n = 12) locations were collected during 12 brake changes and analyzed using phase contrast microscopy (PCM) [National Institute for Occupational Safety and Health (NIOSH) 7400] and TEM (NIOSH 7402). In addition, the fiber distribution by size and morphology was evaluated according to the International Organization for Standardization method for asbestos. Applying the ratio of asbestos fibers:total fibers (including non-asbestos) as determined by TEM to the PCM results, the average airborne chrysotile concentrations (PCM equivalent) were 0.024 f/cc for the mechanic and 0.009 f/cc for persons standing 1.2-3.1 m from the activity during the period of exposure ( approximately 0.5 to 1 h). Considering the time involved in the activity, and assuming three brake jobs per shift, these results would convert to an average 8-h time-weighted average of 0.009 f/cc for a mechanic and 0.006 f/cc for a bystander. The results indicate that (i) the airborne concentrations for worker and bystander samples were significantly less than the current occupational exposure limit of 0.1 f/cc; (ii
Airborne concentrations of benzene due to diesel locomotive exhaust in a roundhouse.
Madl, Amy K; Paustenbach, Dennis J
2002-12-13
Concentrations of airborne benzene due to diesel exhaust from a locomotive were measured during a worst-case exposure scenario in a roundhouse. To understand the upper bound human health risk due to benzene, an electromotive diesel and a General Electric four-cycle turbo locomotive were allowed to run for four 30-min intervals during an 8-h workshift in a roundhouse. Full-shift and 1-h airborne concentrations of benzene were measured in the breathing zone of surrogate locomotive repairmen over the 8-h workshift on 2 consecutive days. In addition, carbon monoxide was measured continuously; elemental carbon (surrogate for diesel exhaust) was sampled with full-shift area samples; and nitrogen dioxide/nitric oxide was sampled using full-shift and 15-min (nitrogen dioxide only) area samples. Peak concentrations of carbon monoxide ranged from 22.5 to 93 ppm. The average concentration of elemental carbon for each day of the roundhouse study was 0.0543 and 0.0552 microg/m(3 )for an 8-h workshift. These were considered "worst-case" conditions since the work environment was intolerably irritating to the eyes, nose, and throat. Short-term nitrogen dioxide concentrations ranged from 0.81 to 2.63 ppm during the diesel emission events with the doors closed. One-hour airborne benzene concentrations ranged from 0.001 to 0.015 ppm with 45% of the measurements below the detection limit of 0.002-0.004 ppm. Results indicated that the 8-h time-weighted average for benzene in the roundhouse was approximately 100-fold less than the current threshold limit value (TLV) of 0.5 ppm. These data are consistent with other studies, which have indicated that benzene concentrations due to diesel emissions, even in a confined environment, are quite low.
Radon concentration in The Netherlands
International Nuclear Information System (INIS)
Meijer, R.J. de; Put, L.W.; Veldhuizen, A.
1986-02-01
In 1000 dwellings, which can be assumed to be an reasonable representation of the average Dutch dwellings, time averaged radon concentrations, radon daughter concentrations and gamma-exposure tempi are determined during a year with passive dosemeters. They are also determined outdoor at circa 200 measure points. (Auth.)
Improved averaging for non-null interferometry
Fleig, Jon F.; Murphy, Paul E.
2013-09-01
Arithmetic averaging of interferometric phase measurements is a well-established method for reducing the effects of time varying disturbances, such as air turbulence and vibration. Calculating a map of the standard deviation for each pixel in the average map can provide a useful estimate of its variability. However, phase maps of complex and/or high density fringe fields frequently contain defects that severely impair the effectiveness of simple phase averaging and bias the variability estimate. These defects include large or small-area phase unwrapping artifacts, large alignment components, and voids that change in number, location, or size. Inclusion of a single phase map with a large area defect into the average is usually sufficient to spoil the entire result. Small-area phase unwrapping and void defects may not render the average map metrologically useless, but they pessimistically bias the variance estimate for the overwhelming majority of the data. We present an algorithm that obtains phase average and variance estimates that are robust against both large and small-area phase defects. It identifies and rejects phase maps containing large area voids or unwrapping artifacts. It also identifies and prunes the unreliable areas of otherwise useful phase maps, and removes the effect of alignment drift from the variance estimate. The algorithm has several run-time adjustable parameters to adjust the rejection criteria for bad data. However, a single nominal setting has been effective over a wide range of conditions. This enhanced averaging algorithm can be efficiently integrated with the phase map acquisition process to minimize the number of phase samples required to approach the practical noise floor of the metrology environment.
Asynchronous Gossip for Averaging and Spectral Ranking
Borkar, Vivek S.; Makhijani, Rahul; Sundaresan, Rajesh
2014-08-01
We consider two variants of the classical gossip algorithm. The first variant is a version of asynchronous stochastic approximation. We highlight a fundamental difficulty associated with the classical asynchronous gossip scheme, viz., that it may not converge to a desired average, and suggest an alternative scheme based on reinforcement learning that has guaranteed convergence to the desired average. We then discuss a potential application to a wireless network setting with simultaneous link activation constraints. The second variant is a gossip algorithm for distributed computation of the Perron-Frobenius eigenvector of a nonnegative matrix. While the first variant draws upon a reinforcement learning algorithm for an average cost controlled Markov decision problem, the second variant draws upon a reinforcement learning algorithm for risk-sensitive control. We then discuss potential applications of the second variant to ranking schemes, reputation networks, and principal component analysis.
Benchmarking statistical averaging of spectra with HULLAC
Klapisch, Marcel; Busquet, Michel
2008-11-01
Knowledge of radiative properties of hot plasmas is important for ICF, astrophysics, etc When mid-Z or high-Z elements are present, the spectra are so complex that one commonly uses statistically averaged description of atomic systems [1]. In a recent experiment on Fe[2], performed under controlled conditions, high resolution transmission spectra were obtained. The new version of HULLAC [3] allows the use of the same model with different levels of details/averaging. We will take advantage of this feature to check the effect of averaging with comparison with experiment. [1] A Bar-Shalom, J Oreg, and M Klapisch, J. Quant. Spectros. Rad. Transf. 65, 43 (2000). [2] J. E. Bailey, G. A. Rochau, C. A. Iglesias et al., Phys. Rev. Lett. 99, 265002-4 (2007). [3]. M. Klapisch, M. Busquet, and A. Bar-Shalom, AIP Conference Proceedings 926, 206-15 (2007).
An approach to averaging digitized plantagram curves.
Hawes, M R; Heinemeyer, R; Sovak, D; Tory, B
1994-07-01
The averaging of outline shapes of the human foot for the purposes of determining information concerning foot shape and dimension within the context of comfort of fit of sport shoes is approached as a mathematical problem. An outline of the human footprint is obtained by standard procedures and the curvature is traced with a Hewlett Packard Digitizer. The paper describes the determination of an alignment axis, the identification of two ray centres and the division of the total curve into two overlapping arcs. Each arc is divided by equiangular rays which intersect chords between digitized points describing the arc. The radial distance of each ray is averaged within groups of foot lengths which vary by +/- 2.25 mm (approximately equal to 1/2 shoe size). The method has been used to determine average plantar curves in a study of 1197 North American males (Hawes and Sovak 1993).
Books average previous decade of economic misery.
Bentley, R Alexander; Acerbi, Alberto; Ormerod, Paul; Lampos, Vasileios
2014-01-01
For the 20(th) century since the Depression, we find a strong correlation between a 'literary misery index' derived from English language books and a moving average of the previous decade of the annual U.S. economic misery index, which is the sum of inflation and unemployment rates. We find a peak in the goodness of fit at 11 years for the moving average. The fit between the two misery indices holds when using different techniques to measure the literary misery index, and this fit is significantly better than other possible correlations with different emotion indices. To check the robustness of the results, we also analysed books written in German language and obtained very similar correlations with the German economic misery index. The results suggest that millions of books published every year average the authors' shared economic experiences over the past decade.
Books Average Previous Decade of Economic Misery
Bentley, R. Alexander; Acerbi, Alberto; Ormerod, Paul; Lampos, Vasileios
2014-01-01
For the 20th century since the Depression, we find a strong correlation between a ‘literary misery index’ derived from English language books and a moving average of the previous decade of the annual U.S. economic misery index, which is the sum of inflation and unemployment rates. We find a peak in the goodness of fit at 11 years for the moving average. The fit between the two misery indices holds when using different techniques to measure the literary misery index, and this fit is significantly better than other possible correlations with different emotion indices. To check the robustness of the results, we also analysed books written in German language and obtained very similar correlations with the German economic misery index. The results suggest that millions of books published every year average the authors' shared economic experiences over the past decade. PMID:24416159
Exploiting scale dependence in cosmological averaging
International Nuclear Information System (INIS)
Mattsson, Teppo; Ronkainen, Maria
2008-01-01
We study the role of scale dependence in the Buchert averaging method, using the flat Lemaitre–Tolman–Bondi model as a testing ground. Within this model, a single averaging scale gives predictions that are too coarse, but by replacing it with the distance of the objects R(z) for each redshift z, we find an O(1%) precision at z<2 in the averaged luminosity and angular diameter distances compared to their exact expressions. At low redshifts, we show the improvement for generic inhomogeneity profiles, and our numerical computations further verify it up to redshifts z∼2. At higher redshifts, the method breaks down due to its inability to capture the time evolution of the inhomogeneities. We also demonstrate that the running smoothing scale R(z) can mimic acceleration, suggesting that it could be at least as important as the backreaction in explaining dark energy as an inhomogeneity induced illusion
Stochastic Averaging and Stochastic Extremum Seeking
Liu, Shu-Jun
2012-01-01
Stochastic Averaging and Stochastic Extremum Seeking develops methods of mathematical analysis inspired by the interest in reverse engineering and analysis of bacterial convergence by chemotaxis and to apply similar stochastic optimization techniques in other environments. The first half of the text presents significant advances in stochastic averaging theory, necessitated by the fact that existing theorems are restricted to systems with linear growth, globally exponentially stable average models, vanishing stochastic perturbations, and prevent analysis over infinite time horizon. The second half of the text introduces stochastic extremum seeking algorithms for model-free optimization of systems in real time using stochastic perturbations for estimation of their gradients. Both gradient- and Newton-based algorithms are presented, offering the user the choice between the simplicity of implementation (gradient) and the ability to achieve a known, arbitrary convergence rate (Newton). The design of algorithms...
Aperture averaging in strong oceanic turbulence
Gökçe, Muhsin Caner; Baykal, Yahya
2018-04-01
Receiver aperture averaging technique is employed in underwater wireless optical communication (UWOC) systems to mitigate the effects of oceanic turbulence, thus to improve the system performance. The irradiance flux variance is a measure of the intensity fluctuations on a lens of the receiver aperture. Using the modified Rytov theory which uses the small-scale and large-scale spatial filters, and our previously presented expression that shows the atmospheric structure constant in terms of oceanic turbulence parameters, we evaluate the irradiance flux variance and the aperture averaging factor of a spherical wave in strong oceanic turbulence. Irradiance flux variance variations are examined versus the oceanic turbulence parameters and the receiver aperture diameter are examined in strong oceanic turbulence. Also, the effect of the receiver aperture diameter on the aperture averaging factor is presented in strong oceanic turbulence.
Regional averaging and scaling in relativistic cosmology
International Nuclear Information System (INIS)
Buchert, Thomas; Carfora, Mauro
2002-01-01
Averaged inhomogeneous cosmologies lie at the forefront of interest, since cosmological parameters such as the rate of expansion or the mass density are to be considered as volume-averaged quantities and only these can be compared with observations. For this reason the relevant parameters are intrinsically scale-dependent and one wishes to control this dependence without restricting the cosmological model by unphysical assumptions. In the latter respect we contrast our way to approach the averaging problem in relativistic cosmology with shortcomings of averaged Newtonian models. Explicitly, we investigate the scale-dependence of Eulerian volume averages of scalar functions on Riemannian three-manifolds. We propose a complementary view of a Lagrangian smoothing of (tensorial) variables as opposed to their Eulerian averaging on spatial domains. This programme is realized with the help of a global Ricci deformation flow for the metric. We explain rigorously the origin of the Ricci flow which, on heuristic grounds, has already been suggested as a possible candidate for smoothing the initial dataset for cosmological spacetimes. The smoothing of geometry implies a renormalization of averaged spatial variables. We discuss the results in terms of effective cosmological parameters that would be assigned to the smoothed cosmological spacetime. In particular, we find that on the smoothed spatial domain B-bar evaluated cosmological parameters obey Ω-bar B-bar m + Ω-bar B-bar R + Ω-bar B-bar A + Ω-bar B-bar Q 1, where Ω-bar B-bar m , Ω-bar B-bar R and Ω-bar B-bar A correspond to the standard Friedmannian parameters, while Ω-bar B-bar Q is a remnant of cosmic variance of expansion and shear fluctuations on the averaging domain. All these parameters are 'dressed' after smoothing out the geometrical fluctuations, and we give the relations of the 'dressed' to the 'bare' parameters. While the former provide the framework of interpreting observations with a 'Friedmannian bias
Average: the juxtaposition of procedure and context
Watson, Jane; Chick, Helen; Callingham, Rosemary
2014-09-01
This paper presents recent data on the performance of 247 middle school students on questions concerning average in three contexts. Analysis includes considering levels of understanding linking definition and context, performance across contexts, the relative difficulty of tasks, and difference in performance for male and female students. The outcomes lead to a discussion of the expectations of the curriculum and its implementation, as well as assessment, in relation to students' skills in carrying out procedures and their understanding about the meaning of average in context.
Average-case analysis of numerical problems
2000-01-01
The average-case analysis of numerical problems is the counterpart of the more traditional worst-case approach. The analysis of average error and cost leads to new insight on numerical problems as well as to new algorithms. The book provides a survey of results that were mainly obtained during the last 10 years and also contains new results. The problems under consideration include approximation/optimal recovery and numerical integration of univariate and multivariate functions as well as zero-finding and global optimization. Background material, e.g. on reproducing kernel Hilbert spaces and random fields, is provided.
Grassmann Averages for Scalable Robust PCA
DEFF Research Database (Denmark)
Hauberg, Søren; Feragen, Aasa; Black, Michael J.
2014-01-01
As the collection of large datasets becomes increasingly automated, the occurrence of outliers will increase—“big data” implies “big outliers”. While principal component analysis (PCA) is often used to reduce the size of data, and scalable solutions exist, it is well-known that outliers can...... to vectors (subspaces) or elements of vectors; we focus on the latter and use a trimmed average. The resulting Trimmed Grassmann Average (TGA) is particularly appropriate for computer vision because it is robust to pixel outliers. The algorithm has low computational complexity and minimal memory requirements...
DEFF Research Database (Denmark)
Rose, Caspar
2014-01-01
This entry summarizes the main theoretical contributions and empirical findings in relation to concentrated ownership from a law and economics perspective. The various forms of concentrated ownership are described as well as analyzed from the perspective of the legal protection of investors......, especially minority shareholders. Concentrated ownership is associated with benefits and costs. Concentrated ownership may reduce agency costs by increased monitoring of top management. However, concentrated ownership may also provide dominating owners with private benefits of control....
Model averaging, optimal inference and habit formation
Directory of Open Access Journals (Sweden)
Thomas H B FitzGerald
2014-06-01
Full Text Available Postulating that the brain performs approximate Bayesian inference generates principled and empirically testable models of neuronal function – the subject of much current interest in neuroscience and related disciplines. Current formulations address inference and learning under some assumed and particular model. In reality, organisms are often faced with an additional challenge – that of determining which model or models of their environment are the best for guiding behaviour. Bayesian model averaging – which says that an agent should weight the predictions of different models according to their evidence – provides a principled way to solve this problem. Importantly, because model evidence is determined by both the accuracy and complexity of the model, optimal inference requires that these be traded off against one another. This means an agent’s behaviour should show an equivalent balance. We hypothesise that Bayesian model averaging plays an important role in cognition, given that it is both optimal and realisable within a plausible neuronal architecture. We outline model averaging and how it might be implemented, and then explore a number of implications for brain and behaviour. In particular, we propose that model averaging can explain a number of apparently suboptimal phenomena within the framework of approximate (bounded Bayesian inference, focussing particularly upon the relationship between goal-directed and habitual behaviour.
Generalized Jackknife Estimators of Weighted Average Derivatives
DEFF Research Database (Denmark)
Cattaneo, Matias D.; Crump, Richard K.; Jansson, Michael
With the aim of improving the quality of asymptotic distributional approximations for nonlinear functionals of nonparametric estimators, this paper revisits the large-sample properties of an important member of that class, namely a kernel-based weighted average derivative estimator. Asymptotic...
Average beta measurement in EXTRAP T1
International Nuclear Information System (INIS)
Hedin, E.R.
1988-12-01
Beginning with the ideal MHD pressure balance equation, an expression for the average poloidal beta, Β Θ , is derived. A method for unobtrusively measuring the quantities used to evaluate Β Θ in Extrap T1 is described. The results if a series of measurements yielding Β Θ as a function of externally applied toroidal field are presented. (author)
HIGH AVERAGE POWER OPTICAL FEL AMPLIFIERS
International Nuclear Information System (INIS)
2005-01-01
Historically, the first demonstration of the optical FEL was in an amplifier configuration at Stanford University [l]. There were other notable instances of amplifying a seed laser, such as the LLNL PALADIN amplifier [2] and the BNL ATF High-Gain Harmonic Generation FEL [3]. However, for the most part FELs are operated as oscillators or self amplified spontaneous emission devices. Yet, in wavelength regimes where a conventional laser seed can be used, the FEL can be used as an amplifier. One promising application is for very high average power generation, for instance FEL's with average power of 100 kW or more. The high electron beam power, high brightness and high efficiency that can be achieved with photoinjectors and superconducting Energy Recovery Linacs (ERL) combine well with the high-gain FEL amplifier to produce unprecedented average power FELs. This combination has a number of advantages. In particular, we show that for a given FEL power, an FEL amplifier can introduce lower energy spread in the beam as compared to a traditional oscillator. This properly gives the ERL based FEL amplifier a great wall-plug to optical power efficiency advantage. The optics for an amplifier is simple and compact. In addition to the general features of the high average power FEL amplifier, we will look at a 100 kW class FEL amplifier is being designed to operate on the 0.5 ampere Energy Recovery Linac which is under construction at Brookhaven National Laboratory's Collider-Accelerator Department
Bayesian Averaging is Well-Temperated
DEFF Research Database (Denmark)
Hansen, Lars Kai
2000-01-01
Bayesian predictions are stochastic just like predictions of any other inference scheme that generalize from a finite sample. While a simple variational argument shows that Bayes averaging is generalization optimal given that the prior matches the teacher parameter distribution the situation is l...
Gibbs equilibrium averages and Bogolyubov measure
International Nuclear Information System (INIS)
Sankovich, D.P.
2011-01-01
Application of the functional integration methods in equilibrium statistical mechanics of quantum Bose-systems is considered. We show that Gibbs equilibrium averages of Bose-operators can be represented as path integrals over a special Gauss measure defined in the corresponding space of continuous functions. We consider some problems related to integration with respect to this measure
High average-power induction linacs
International Nuclear Information System (INIS)
Prono, D.S.; Barrett, D.; Bowles, E.; Caporaso, G.J.; Chen, Yu-Jiuan; Clark, J.C.; Coffield, F.; Newton, M.A.; Nexsen, W.; Ravenscroft, D.; Turner, W.C.; Watson, J.A.
1989-01-01
Induction linear accelerators (LIAs) are inherently capable of accelerating several thousand amperes of ∼ 50-ns duration pulses to > 100 MeV. In this paper the authors report progress and status in the areas of duty factor and stray power management. These technologies are vital if LIAs are to attain high average power operation. 13 figs
Function reconstruction from noisy local averages
International Nuclear Information System (INIS)
Chen Yu; Huang Jianguo; Han Weimin
2008-01-01
A regularization method is proposed for the function reconstruction from noisy local averages in any dimension. Error bounds for the approximate solution in L 2 -norm are derived. A number of numerical examples are provided to show computational performance of the method, with the regularization parameters selected by different strategies
A singularity theorem based on spatial averages
Indian Academy of Sciences (India)
journal of. July 2007 physics pp. 31–47. A singularity theorem based on spatial ... In this paper I would like to present a result which confirms – at least partially – ... A detailed analysis of how the model fits in with the .... Further, the statement that the spatial average ...... Financial support under grants FIS2004-01626 and no.
Multiphase averaging of periodic soliton equations
International Nuclear Information System (INIS)
Forest, M.G.
1979-01-01
The multiphase averaging of periodic soliton equations is considered. Particular attention is given to the periodic sine-Gordon and Korteweg-deVries (KdV) equations. The periodic sine-Gordon equation and its associated inverse spectral theory are analyzed, including a discussion of the spectral representations of exact, N-phase sine-Gordon solutions. The emphasis is on physical characteristics of the periodic waves, with a motivation from the well-known whole-line solitons. A canonical Hamiltonian approach for the modulational theory of N-phase waves is prescribed. A concrete illustration of this averaging method is provided with the periodic sine-Gordon equation; explicit averaging results are given only for the N = 1 case, laying a foundation for a more thorough treatment of the general N-phase problem. For the KdV equation, very general results are given for multiphase averaging of the N-phase waves. The single-phase results of Whitham are extended to general N phases, and more importantly, an invariant representation in terms of Abelian differentials on a Riemann surface is provided. Several consequences of this invariant representation are deduced, including strong evidence for the Hamiltonian structure of N-phase modulational equations
A dynamic analysis of moving average rules
Chiarella, C.; He, X.Z.; Hommes, C.H.
2006-01-01
The use of various moving average (MA) rules remains popular with financial market practitioners. These rules have recently become the focus of a number empirical studies, but there have been very few studies of financial market models where some agents employ technical trading rules of the type
Essays on model averaging and political economics
Wang, W.
2013-01-01
This thesis first investigates various issues related with model averaging, and then evaluates two policies, i.e. West Development Drive in China and fiscal decentralization in U.S, using econometric tools. Chapter 2 proposes a hierarchical weighted least squares (HWALS) method to address multiple
2010-01-01
... 7 Agriculture 10 2010-01-01 2010-01-01 false On average. 1209.12 Section 1209.12 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... CONSUMER INFORMATION ORDER Mushroom Promotion, Research, and Consumer Information Order Definitions § 1209...
High average-power induction linacs
International Nuclear Information System (INIS)
Prono, D.S.; Barrett, D.; Bowles, E.
1989-01-01
Induction linear accelerators (LIAs) are inherently capable of accelerating several thousand amperes of /approximately/ 50-ns duration pulses to > 100 MeV. In this paper we report progress and status in the areas of duty factor and stray power management. These technologies are vital if LIAs are to attain high average power operation. 13 figs
Average Costs versus Net Present Value
E.A. van der Laan (Erwin); R.H. Teunter (Ruud)
2000-01-01
textabstractWhile the net present value (NPV) approach is widely accepted as the right framework for studying production and inventory control systems, average cost (AC) models are more widely used. For the well known EOQ model it can be verified that (under certain conditions) the AC approach gives
Average beta-beating from random errors
Tomas Garcia, Rogelio; Langner, Andy Sven; Malina, Lukas; Franchi, Andrea; CERN. Geneva. ATS Department
2018-01-01
The impact of random errors on average β-beating is studied via analytical derivations and simulations. A systematic positive β-beating is expected from random errors quadratic with the sources or, equivalently, with the rms β-beating. However, random errors do not have a systematic eﬀect on the tune.
Reliability Estimates for Undergraduate Grade Point Average
Westrick, Paul A.
2017-01-01
Undergraduate grade point average (GPA) is a commonly employed measure in educational research, serving as a criterion or as a predictor depending on the research question. Over the decades, researchers have used a variety of reliability coefficients to estimate the reliability of undergraduate GPA, which suggests that there has been no consensus…
Tendon surveillance requirements - average tendon force
International Nuclear Information System (INIS)
Fulton, J.F.
1982-01-01
Proposed Rev. 3 to USNRC Reg. Guide 1.35 discusses the need for comparing, for individual tendons, the measured and predicted lift-off forces. Such a comparison is intended to detect any abnormal tendon force loss which might occur. Recognizing that there are uncertainties in the prediction of tendon losses, proposed Guide 1.35.1 has allowed specific tolerances on the fundamental losses. Thus, the lift-off force acceptance criteria for individual tendons appearing in Reg. Guide 1.35, Proposed Rev. 3, is stated relative to a lower bound predicted tendon force, which is obtained using the 'plus' tolerances on the fundamental losses. There is an additional acceptance criterion for the lift-off forces which is not specifically addressed in these two Reg. Guides; however, it is included in a proposed Subsection IWX to ASME Code Section XI. This criterion is based on the overriding requirement that the magnitude of prestress in the containment structure be sufficeint to meet the minimum prestress design requirements. This design requirement can be expressed as an average tendon force for each group of vertical hoop, or dome tendons. For the purpose of comparing the actual tendon forces with the required average tendon force, the lift-off forces measured for a sample of tendons within each group can be averaged to construct the average force for the entire group. However, the individual lift-off forces must be 'corrected' (normalized) prior to obtaining the sample average. This paper derives the correction factor to be used for this purpose. (orig./RW)
Garcia-Botella, Angel; Fernandez-Balbuena, Antonio Alvarez; Bernabeu, Eusebio
2006-10-10
Nonimaging optics is a field devoted to the design of optical components for applications such as solar concentration or illumination. In this field, many different techniques have been used to produce optical devices, including the use of reflective and refractive components or inverse engineering techniques. However, many of these optical components are based on translational symmetries, rotational symmetries, or free-form surfaces. We study a new family of nonimaging concentrators called elliptical concentrators. This new family of concentrators provides new capabilities and can have different configurations, either homofocal or nonhomofocal. Translational and rotational concentrators can be considered as particular cases of elliptical concentrators.
Statistics on exponential averaging of periodograms
Energy Technology Data Exchange (ETDEWEB)
Peeters, T.T.J.M. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Ciftcioglu, Oe. [Istanbul Technical Univ. (Turkey). Dept. of Electrical Engineering
1994-11-01
The algorithm of exponential averaging applied to subsequent periodograms of a stochastic process is used to estimate the power spectral density (PSD). For an independent process, assuming the periodogram estimates to be distributed according to a {chi}{sup 2} distribution with 2 degrees of freedom, the probability density function (PDF) of the PSD estimate is derived. A closed expression is obtained for the moments of the distribution. Surprisingly, the proof of this expression features some new insights into the partitions and Eulers infinite product. For large values of the time constant of the averaging process, examination of the cumulant generating function shows that the PDF approximates the Gaussian distribution. Although restrictions for the statistics are seemingly tight, simulation of a real process indicates a wider applicability of the theory. (orig.).
Statistics on exponential averaging of periodograms
International Nuclear Information System (INIS)
Peeters, T.T.J.M.; Ciftcioglu, Oe.
1994-11-01
The algorithm of exponential averaging applied to subsequent periodograms of a stochastic process is used to estimate the power spectral density (PSD). For an independent process, assuming the periodogram estimates to be distributed according to a χ 2 distribution with 2 degrees of freedom, the probability density function (PDF) of the PSD estimate is derived. A closed expression is obtained for the moments of the distribution. Surprisingly, the proof of this expression features some new insights into the partitions and Eulers infinite product. For large values of the time constant of the averaging process, examination of the cumulant generating function shows that the PDF approximates the Gaussian distribution. Although restrictions for the statistics are seemingly tight, simulation of a real process indicates a wider applicability of the theory. (orig.)
ANALYSIS OF THE FACTORS AFFECTING THE AVERAGE
Directory of Open Access Journals (Sweden)
Carmen BOGHEAN
2013-12-01
Full Text Available Productivity in agriculture most relevantly and concisely expresses the economic efficiency of using the factors of production. Labour productivity is affected by a considerable number of variables (including the relationship system and interdependence between factors, which differ in each economic sector and influence it, giving rise to a series of technical, economic and organizational idiosyncrasies. The purpose of this paper is to analyse the underlying factors of the average work productivity in agriculture, forestry and fishing. The analysis will take into account the data concerning the economically active population and the gross added value in agriculture, forestry and fishing in Romania during 2008-2011. The distribution of the average work productivity per factors affecting it is conducted by means of the u-substitution method.
Weighted estimates for the averaging integral operator
Czech Academy of Sciences Publication Activity Database
Opic, Bohumír; Rákosník, Jiří
2010-01-01
Roč. 61, č. 3 (2010), s. 253-262 ISSN 0010-0757 R&D Projects: GA ČR GA201/05/2033; GA ČR GA201/08/0383 Institutional research plan: CEZ:AV0Z10190503 Keywords : averaging integral operator * weighted Lebesgue spaces * weights Subject RIV: BA - General Mathematics Impact factor: 0.474, year: 2010 http://link.springer.com/article/10.1007%2FBF03191231
Average Transverse Momentum Quantities Approaching the Lightfront
Boer, Daniel
2015-01-01
In this contribution to Light Cone 2014, three average transverse momentum quantities are discussed: the Sivers shift, the dijet imbalance, and the $p_T$ broadening. The definitions of these quantities involve integrals over all transverse momenta that are overly sensitive to the region of large transverse momenta, which conveys little information about the transverse momentum distributions of quarks and gluons inside hadrons. TMD factorization naturally suggests alternative definitions of su...
Time-averaged MSD of Brownian motion
Andreanov, Alexei; Grebenkov, Denis
2012-01-01
We study the statistical properties of the time-averaged mean-square displacements (TAMSD). This is a standard non-local quadratic functional for inferring the diffusion coefficient from an individual random trajectory of a diffusing tracer in single-particle tracking experiments. For Brownian motion, we derive an exact formula for the Laplace transform of the probability density of the TAMSD by mapping the original problem onto chains of coupled harmonic oscillators. From this formula, we de...
Average configuration of the geomagnetic tail
International Nuclear Information System (INIS)
Fairfield, D.H.
1979-01-01
Over 3000 hours of Imp 6 magnetic field data obtained between 20 and 33 R/sub E/ in the geomagnetic tail have been used in a statistical study of the tail configuration. A distribution of 2.5-min averages of B/sub z/ as a function of position across the tail reveals that more flux crosses the equatorial plane near the dawn and dusk flanks (B-bar/sub z/=3.γ) than near midnight (B-bar/sub z/=1.8γ). The tail field projected in the solar magnetospheric equatorial plane deviates from the x axis due to flaring and solar wind aberration by an angle α=-0.9 Y/sub SM/-2.7, where Y/sub SM/ is in earth radii and α is in degrees. After removing these effects, the B/sub y/ component of the tail field is found to depend on interplanetary sector structure. During an 'away' sector the B/sub y/ component of the tail field is on average 0.5γ greater than that during a 'toward' sector, a result that is true in both tail lobes and is independent of location across the tail. This effect means the average field reversal between northern and southern lobes of the tail is more often 178 0 rather than the 180 0 that is generally supposed
Unscrambling The "Average User" Of Habbo Hotel
Directory of Open Access Journals (Sweden)
Mikael Johnson
2007-01-01
Full Text Available The “user” is an ambiguous concept in human-computer interaction and information systems. Analyses of users as social actors, participants, or configured users delineate approaches to studying design-use relationships. Here, a developer’s reference to a figure of speech, termed the “average user,” is contrasted with design guidelines. The aim is to create an understanding about categorization practices in design through a case study about the virtual community, Habbo Hotel. A qualitative analysis highlighted not only the meaning of the “average user,” but also the work that both the developer and the category contribute to this meaning. The average user a represents the unknown, b influences the boundaries of the target user groups, c legitimizes the designer to disregard marginal user feedback, and d keeps the design space open, thus allowing for creativity. The analysis shows how design and use are intertwined and highlights the developers’ role in governing different users’ interests.
Changing mortality and average cohort life expectancy
Directory of Open Access Journals (Sweden)
Robert Schoen
2005-10-01
Full Text Available Period life expectancy varies with changes in mortality, and should not be confused with the life expectancy of those alive during that period. Given past and likely future mortality changes, a recent debate has arisen on the usefulness of the period life expectancy as the leading measure of survivorship. An alternative aggregate measure of period mortality which has been seen as less sensitive to period changes, the cross-sectional average length of life (CAL has been proposed as an alternative, but has received only limited empirical or analytical examination. Here, we introduce a new measure, the average cohort life expectancy (ACLE, to provide a precise measure of the average length of life of cohorts alive at a given time. To compare the performance of ACLE with CAL and with period and cohort life expectancy, we first use population models with changing mortality. Then the four aggregate measures of mortality are calculated for England and Wales, Norway, and Switzerland for the years 1880 to 2000. CAL is found to be sensitive to past and present changes in death rates. ACLE requires the most data, but gives the best representation of the survivorship of cohorts present at a given time.
Average subentropy, coherence and entanglement of random mixed quantum states
Energy Technology Data Exchange (ETDEWEB)
Zhang, Lin, E-mail: godyalin@163.com [Institute of Mathematics, Hangzhou Dianzi University, Hangzhou 310018 (China); Singh, Uttam, E-mail: uttamsingh@hri.res.in [Harish-Chandra Research Institute, Allahabad, 211019 (India); Pati, Arun K., E-mail: akpati@hri.res.in [Harish-Chandra Research Institute, Allahabad, 211019 (India)
2017-02-15
Compact expressions for the average subentropy and coherence are obtained for random mixed states that are generated via various probability measures. Surprisingly, our results show that the average subentropy of random mixed states approaches the maximum value of the subentropy which is attained for the maximally mixed state as we increase the dimension. In the special case of the random mixed states sampled from the induced measure via partial tracing of random bipartite pure states, we establish the typicality of the relative entropy of coherence for random mixed states invoking the concentration of measure phenomenon. Our results also indicate that mixed quantum states are less useful compared to pure quantum states in higher dimension when we extract quantum coherence as a resource. This is because of the fact that average coherence of random mixed states is bounded uniformly, however, the average coherence of random pure states increases with the increasing dimension. As an important application, we establish the typicality of relative entropy of entanglement and distillable entanglement for a specific class of random bipartite mixed states. In particular, most of the random states in this specific class have relative entropy of entanglement and distillable entanglement equal to some fixed number (to within an arbitrary small error), thereby hugely reducing the complexity of computation of these entanglement measures for this specific class of mixed states.
Directory of Open Access Journals (Sweden)
Matić Vesna
2016-01-01
Full Text Available Concentration risk has been gaining a special dimension in the contemporary financial and economic environment. Financial institutions are exposed to this risk mainly in the field of lending, mostly through their credit activities and concentration of credit portfolios. This refers to the concentration of different exposures within a single risk category (credit risk, market risk, operational risk, liquidity risk.
Luque, Antonio L
2007-01-01
Photovoltaic solar-energy conversion is one of the most promising technologies for generating renewable energy, and conversion of concentrated sunlight can lead to reduced cost for solar electricity. In fact, photovoltaic conversion of concentrated sunlight insures an efficient and cost-effective sustainable power resource. This book gives an overview of all components, e.g. cells, concentrators, modules and systems, for systems of concentrator photovoltaics. The authors report on significant results related to design, technology, and applications, and also cover the fundamental physics and market considerations. Specific contributions include: theory and practice of sunlight concentrators; an overview of concentrator PV activities; a description of concentrator solar cells; design and technology of modules and systems; manufacturing aspects; and a market study.
Operator product expansion and its thermal average
Energy Technology Data Exchange (ETDEWEB)
Mallik, S [Saha Inst. of Nuclear Physics, Calcutta (India)
1998-05-01
QCD sum rules at finite temperature, like the ones at zero temperature, require the coefficients of local operators, which arise in the short distance expansion of the thermal average of two-point functions of currents. We extend the configuration space method, applied earlier at zero temperature, to the case at finite temperature. We find that, upto dimension four, two new operators arise, in addition to the two appearing already in the vacuum correlation functions. It is argued that the new operators would contribute substantially to the sum rules, when the temperature is not too low. (orig.) 7 refs.
Fluctuations of wavefunctions about their classical average
International Nuclear Information System (INIS)
Benet, L; Flores, J; Hernandez-Saldana, H; Izrailev, F M; Leyvraz, F; Seligman, T H
2003-01-01
Quantum-classical correspondence for the average shape of eigenfunctions and the local spectral density of states are well-known facts. In this paper, the fluctuations of the quantum wavefunctions around the classical value are discussed. A simple random matrix model leads to a Gaussian distribution of the amplitudes whose width is determined by the classical shape of the eigenfunction. To compare this prediction with numerical calculations in chaotic models of coupled quartic oscillators, we develop a rescaling method for the components. The expectations are broadly confirmed, but deviations due to scars are observed. This effect is much reduced when both Hamiltonians have chaotic dynamics
Phase-averaged transport for quasiperiodic Hamiltonians
Bellissard, J; Schulz-Baldes, H
2002-01-01
For a class of discrete quasi-periodic Schroedinger operators defined by covariant re- presentations of the rotation algebra, a lower bound on phase-averaged transport in terms of the multifractal dimensions of the density of states is proven. This result is established under a Diophantine condition on the incommensuration parameter. The relevant class of operators is distinguished by invariance with respect to symmetry automorphisms of the rotation algebra. It includes the critical Harper (almost-Mathieu) operator. As a by-product, a new solution of the frame problem associated with Weyl-Heisenberg-Gabor lattices of coherent states is given.
Baseline-dependent averaging in radio interferometry
Wijnholds, S. J.; Willis, A. G.; Salvini, S.
2018-05-01
This paper presents a detailed analysis of the applicability and benefits of baseline-dependent averaging (BDA) in modern radio interferometers and in particular the Square Kilometre Array. We demonstrate that BDA does not affect the information content of the data other than a well-defined decorrelation loss for which closed form expressions are readily available. We verify these theoretical findings using simulations. We therefore conclude that BDA can be used reliably in modern radio interferometry allowing a reduction of visibility data volume (and hence processing costs for handling visibility data) by more than 80 per cent.
Multistage parallel-serial time averaging filters
International Nuclear Information System (INIS)
Theodosiou, G.E.
1980-01-01
Here, a new time averaging circuit design, the 'parallel filter' is presented, which can reduce the time jitter, introduced in time measurements using counters of large dimensions. This parallel filter could be considered as a single stage unit circuit which can be repeated an arbitrary number of times in series, thus providing a parallel-serial filter type as a result. The main advantages of such a filter over a serial one are much less electronic gate jitter and time delay for the same amount of total time uncertainty reduction. (orig.)
Time-averaged MSD of Brownian motion
International Nuclear Information System (INIS)
Andreanov, Alexei; Grebenkov, Denis S
2012-01-01
We study the statistical properties of the time-averaged mean-square displacements (TAMSD). This is a standard non-local quadratic functional for inferring the diffusion coefficient from an individual random trajectory of a diffusing tracer in single-particle tracking experiments. For Brownian motion, we derive an exact formula for the Laplace transform of the probability density of the TAMSD by mapping the original problem onto chains of coupled harmonic oscillators. From this formula, we deduce the first four cumulant moments of the TAMSD, the asymptotic behavior of the probability density and its accurate approximation by a generalized Gamma distribution
Time-dependent angularly averaged inverse transport
International Nuclear Information System (INIS)
Bal, Guillaume; Jollivet, Alexandre
2009-01-01
This paper concerns the reconstruction of the absorption and scattering parameters in a time-dependent linear transport equation from knowledge of angularly averaged measurements performed at the boundary of a domain of interest. Such measurement settings find applications in medical and geophysical imaging. We show that the absorption coefficient and the spatial component of the scattering coefficient are uniquely determined by such measurements. We obtain stability results on the reconstruction of the absorption and scattering parameters with respect to the measured albedo operator. The stability results are obtained by a precise decomposition of the measurements into components with different singular behavior in the time domain
Independence, Odd Girth, and Average Degree
DEFF Research Database (Denmark)
Löwenstein, Christian; Pedersen, Anders Sune; Rautenbach, Dieter
2011-01-01
We prove several tight lower bounds in terms of the order and the average degree for the independence number of graphs that are connected and/or satisfy some odd girth condition. Our main result is the extension of a lower bound for the independence number of triangle-free graphs of maximum...... degree at most three due to Heckman and Thomas [Discrete Math 233 (2001), 233–237] to arbitrary triangle-free graphs. For connected triangle-free graphs of order n and size m, our result implies the existence of an independent set of order at least (4n−m−1) / 7. ...
Bootstrapping Density-Weighted Average Derivatives
DEFF Research Database (Denmark)
Cattaneo, Matias D.; Crump, Richard K.; Jansson, Michael
Employing the "small bandwidth" asymptotic framework of Cattaneo, Crump, and Jansson (2009), this paper studies the properties of a variety of bootstrap-based inference procedures associated with the kernel-based density-weighted averaged derivative estimator proposed by Powell, Stock, and Stoker...... (1989). In many cases validity of bootstrap-based inference procedures is found to depend crucially on whether the bandwidth sequence satisfies a particular (asymptotic linearity) condition. An exception to this rule occurs for inference procedures involving a studentized estimator employing a "robust...
Average Nuclear properties based on statistical model
International Nuclear Information System (INIS)
El-Jaick, L.J.
1974-01-01
The rough properties of nuclei were investigated by statistical model, in systems with the same and different number of protons and neutrons, separately, considering the Coulomb energy in the last system. Some average nuclear properties were calculated based on the energy density of nuclear matter, from Weizsscker-Beth mass semiempiric formulae, generalized for compressible nuclei. In the study of a s surface energy coefficient, the great influence exercised by Coulomb energy and nuclear compressibility was verified. For a good adjust of beta stability lines and mass excess, the surface symmetry energy were established. (M.C.K.) [pt
Time-averaged MSD of Brownian motion
Andreanov, Alexei; Grebenkov, Denis S.
2012-07-01
We study the statistical properties of the time-averaged mean-square displacements (TAMSD). This is a standard non-local quadratic functional for inferring the diffusion coefficient from an individual random trajectory of a diffusing tracer in single-particle tracking experiments. For Brownian motion, we derive an exact formula for the Laplace transform of the probability density of the TAMSD by mapping the original problem onto chains of coupled harmonic oscillators. From this formula, we deduce the first four cumulant moments of the TAMSD, the asymptotic behavior of the probability density and its accurate approximation by a generalized Gamma distribution.
De Luca, G.; Magnus, J.R.
2011-01-01
In this article, we describe the estimation of linear regression models with uncertainty about the choice of the explanatory variables. We introduce the Stata commands bma and wals, which implement, respectively, the exact Bayesian model-averaging estimator and the weighted-average least-squares
Parents' Reactions to Finding Out That Their Children Have Average or above Average IQ Scores.
Dirks, Jean; And Others
1983-01-01
Parents of 41 children who had been given an individually-administered intelligence test were contacted 19 months after testing. Parents of average IQ children were less accurate in their memory of test results. Children with above average IQ experienced extremely low frequencies of sibling rivalry, conceit or pressure. (Author/HLM)
Analysis of the average daily radon variations in the soil air
International Nuclear Information System (INIS)
Holy, K.; Matos, M.; Boehm, R.; Stanys, T.; Polaskova, A.; Hola, O.
1998-01-01
In this contribution the search of the relation between the daily variations of the radon concentration and the regular daily oscillations of the atmospheric pressure are presented. The deviation of the radon activity concentration in the soil air from the average daily value reaches only a few percent. For the dry summer months the average daily course of the radon activity concentration can be described by the obtained equation. The analysis of the average daily courses could give the information concerning the depth of the gas permeable soil layer. The soil parameter is determined by others method with difficulty
Trajectory averaging for stochastic approximation MCMC algorithms
Liang, Faming
2010-10-01
The subject of stochastic approximation was founded by Robbins and Monro [Ann. Math. Statist. 22 (1951) 400-407]. After five decades of continual development, it has developed into an important area in systems control and optimization, and it has also served as a prototype for the development of adaptive algorithms for on-line estimation and control of stochastic systems. Recently, it has been used in statistics with Markov chain Monte Carlo for solving maximum likelihood estimation problems and for general simulation and optimizations. In this paper, we first show that the trajectory averaging estimator is asymptotically efficient for the stochastic approximation MCMC (SAMCMC) algorithm under mild conditions, and then apply this result to the stochastic approximation Monte Carlo algorithm [Liang, Liu and Carroll J. Amer. Statist. Assoc. 102 (2007) 305-320]. The application of the trajectory averaging estimator to other stochastic approximationMCMC algorithms, for example, a stochastic approximation MLE algorithm for missing data problems, is also considered in the paper. © Institute of Mathematical Statistics, 2010.
Averaged null energy condition from causality
Hartman, Thomas; Kundu, Sandipan; Tajdini, Amirhossein
2017-07-01
Unitary, Lorentz-invariant quantum field theories in flat spacetime obey mi-crocausality: commutators vanish at spacelike separation. For interacting theories in more than two dimensions, we show that this implies that the averaged null energy, ∫ duT uu , must be non-negative. This non-local operator appears in the operator product expansion of local operators in the lightcone limit, and therefore contributes to n-point functions. We derive a sum rule that isolates this contribution and is manifestly positive. The argument also applies to certain higher spin operators other than the stress tensor, generating an infinite family of new constraints of the form ∫ duX uuu··· u ≥ 0. These lead to new inequalities for the coupling constants of spinning operators in conformal field theory, which include as special cases (but are generally stronger than) the existing constraints from the lightcone bootstrap, deep inelastic scattering, conformal collider methods, and relative entropy. We also comment on the relation to the recent derivation of the averaged null energy condition from relative entropy, and suggest a more general connection between causality and information-theoretic inequalities in QFT.
Beta-energy averaging and beta spectra
International Nuclear Information System (INIS)
Stamatelatos, M.G.; England, T.R.
1976-07-01
A simple yet highly accurate method for approximately calculating spectrum-averaged beta energies and beta spectra for radioactive nuclei is presented. This method should prove useful for users who wish to obtain accurate answers without complicated calculations of Fermi functions, complex gamma functions, and time-consuming numerical integrations as required by the more exact theoretical expressions. Therefore, this method should be a good time-saving alternative for investigators who need to make calculations involving large numbers of nuclei (e.g., fission products) as well as for occasional users interested in restricted number of nuclides. The average beta-energy values calculated by this method differ from those calculated by ''exact'' methods by no more than 1 percent for nuclides with atomic numbers in the 20 to 100 range and which emit betas of energies up to approximately 8 MeV. These include all fission products and the actinides. The beta-energy spectra calculated by the present method are also of the same quality
Asymptotic Time Averages and Frequency Distributions
Directory of Open Access Journals (Sweden)
Muhammad El-Taha
2016-01-01
Full Text Available Consider an arbitrary nonnegative deterministic process (in a stochastic setting {X(t, t≥0} is a fixed realization, i.e., sample-path of the underlying stochastic process with state space S=(-∞,∞. Using a sample-path approach, we give necessary and sufficient conditions for the long-run time average of a measurable function of process to be equal to the expectation taken with respect to the same measurable function of its long-run frequency distribution. The results are further extended to allow unrestricted parameter (time space. Examples are provided to show that our condition is not superfluous and that it is weaker than uniform integrability. The case of discrete-time processes is also considered. The relationship to previously known sufficient conditions, usually given in stochastic settings, will also be discussed. Our approach is applied to regenerative processes and an extension of a well-known result is given. For researchers interested in sample-path analysis, our results will give them the choice to work with the time average of a process or its frequency distribution function and go back and forth between the two under a mild condition.
Chaotic Universe, Friedmannian on the average 2
Energy Technology Data Exchange (ETDEWEB)
Marochnik, L S [AN SSSR, Moscow. Inst. Kosmicheskikh Issledovanij
1980-11-01
The cosmological solutions are found for the equations for correlators, describing a statistically chaotic Universe, Friedmannian on the average in which delta-correlated fluctuations with amplitudes h >> 1 are excited. For the equation of state of matter p = n epsilon, the kind of solutions depends on the position of maximum of the spectrum of the metric disturbances. The expansion of the Universe, in which long-wave potential and vortical motions and gravitational waves (modes diverging at t ..-->.. 0) had been excited, tends asymptotically to the Friedmannian one at t ..-->.. identity and depends critically on n: at n < 0.26, the solution for the scalefactor is situated higher than the Friedmannian one, and lower at n > 0.26. The influence of finite at t ..-->.. 0 long-wave fluctuation modes leads to an averaged quasiisotropic solution. The contribution of quantum fluctuations and of short-wave parts of the spectrum of classical fluctuations to the expansion law is considered. Their influence is equivalent to the contribution from an ultrarelativistic gas with corresponding energy density and pressure. The restrictions are obtained for the degree of chaos (the spectrum characteristics) compatible with the observed helium abundance, which could have been retained by a completely chaotic Universe during its expansion up to the nucleosynthesis epoch.
Averaging in the presence of sliding errors
International Nuclear Information System (INIS)
Yost, G.P.
1991-08-01
In many cases the precision with which an experiment can measure a physical quantity depends on the value of that quantity. Not having access to the true value, experimental groups are forced to assign their errors based on their own measured value. Procedures which attempt to derive an improved estimate of the true value by a suitable average of such measurements usually weight each experiment's measurement according to the reported variance. However, one is in a position to derive improved error estimates for each experiment from the average itself, provided an approximate idea of the functional dependence of the error on the central value is known. Failing to do so can lead to substantial biases. Techniques which avoid these biases without loss of precision are proposed and their performance is analyzed with examples. These techniques are quite general and can bring about an improvement even when the behavior of the errors is not well understood. Perhaps the most important application of the technique is in fitting curves to histograms
High average power linear induction accelerator development
International Nuclear Information System (INIS)
Bayless, J.R.; Adler, R.J.
1987-07-01
There is increasing interest in linear induction accelerators (LIAs) for applications including free electron lasers, high power microwave generators and other types of radiation sources. Lawrence Livermore National Laboratory has developed LIA technology in combination with magnetic pulse compression techniques to achieve very impressive performance levels. In this paper we will briefly discuss the LIA concept and describe our development program. Our goals are to improve the reliability and reduce the cost of LIA systems. An accelerator is presently under construction to demonstrate these improvements at an energy of 1.6 MeV in 2 kA, 65 ns beam pulses at an average beam power of approximately 30 kW. The unique features of this system are a low cost accelerator design and an SCR-switched, magnetically compressed, pulse power system. 4 refs., 7 figs
FEL system with homogeneous average output
Energy Technology Data Exchange (ETDEWEB)
Douglas, David R.; Legg, Robert; Whitney, R. Roy; Neil, George; Powers, Thomas Joseph
2018-01-16
A method of varying the output of a free electron laser (FEL) on very short time scales to produce a slightly broader, but smooth, time-averaged wavelength spectrum. The method includes injecting into an accelerator a sequence of bunch trains at phase offsets from crest. Accelerating the particles to full energy to result in distinct and independently controlled, by the choice of phase offset, phase-energy correlations or chirps on each bunch train. The earlier trains will be more strongly chirped, the later trains less chirped. For an energy recovered linac (ERL), the beam may be recirculated using a transport system with linear and nonlinear momentum compactions M.sub.56, which are selected to compress all three bunch trains at the FEL with higher order terms managed.
Quetelet, the average man and medical knowledge.
Caponi, Sandra
2013-01-01
Using two books by Adolphe Quetelet, I analyze his theory of the 'average man', which associates biological and social normality with the frequency with which certain characteristics appear in a population. The books are Sur l'homme et le développement de ses facultés and Du systeme social et des lois qui le régissent. Both reveal that Quetelet's ideas are permeated by explanatory strategies drawn from physics and astronomy, and also by discursive strategies drawn from theology and religion. The stability of the mean as opposed to the dispersion of individual characteristics and events provided the basis for the use of statistics in social sciences and medicine.
[Quetelet, the average man and medical knowledge].
Caponi, Sandra
2013-01-01
Using two books by Adolphe Quetelet, I analyze his theory of the 'average man', which associates biological and social normality with the frequency with which certain characteristics appear in a population. The books are Sur l'homme et le développement de ses facultés and Du systeme social et des lois qui le régissent. Both reveal that Quetelet's ideas are permeated by explanatory strategies drawn from physics and astronomy, and also by discursive strategies drawn from theology and religion. The stability of the mean as opposed to the dispersion of individual characteristics and events provided the basis for the use of statistics in social sciences and medicine.
Asymmetric network connectivity using weighted harmonic averages
Morrison, Greg; Mahadevan, L.
2011-02-01
We propose a non-metric measure of the "closeness" felt between two nodes in an undirected, weighted graph using a simple weighted harmonic average of connectivity, that is a real-valued Generalized Erdös Number (GEN). While our measure is developed with a collaborative network in mind, the approach can be of use in a variety of artificial and real-world networks. We are able to distinguish between network topologies that standard distance metrics view as identical, and use our measure to study some simple analytically tractable networks. We show how this might be used to look at asymmetry in authorship networks such as those that inspired the integer Erdös numbers in mathematical coauthorships. We also show the utility of our approach to devise a ratings scheme that we apply to the data from the NetFlix prize, and find a significant improvement using our method over a baseline.
Angle-averaged Compton cross sections
International Nuclear Information System (INIS)
Nickel, G.H.
1983-01-01
The scattering of a photon by an individual free electron is characterized by six quantities: α = initial photon energy in units of m 0 c 2 ; α/sub s/ = scattered photon energy in units of m 0 c 2 ; β = initial electron velocity in units of c; phi = angle between photon direction and electron direction in the laboratory frame (LF); theta = polar angle change due to Compton scattering, measured in the electron rest frame (ERF); and tau = azimuthal angle change in the ERF. We present an analytic expression for the average of the Compton cross section over phi, theta, and tau. The lowest order approximation to this equation is reasonably accurate for photons and electrons with energies of many keV
Average Gait Differential Image Based Human Recognition
Directory of Open Access Journals (Sweden)
Jinyan Chen
2014-01-01
Full Text Available The difference between adjacent frames of human walking contains useful information for human gait identification. Based on the previous idea a silhouettes difference based human gait recognition method named as average gait differential image (AGDI is proposed in this paper. The AGDI is generated by the accumulation of the silhouettes difference between adjacent frames. The advantage of this method lies in that as a feature image it can preserve both the kinetic and static information of walking. Comparing to gait energy image (GEI, AGDI is more fit to representation the variation of silhouettes during walking. Two-dimensional principal component analysis (2DPCA is used to extract features from the AGDI. Experiments on CASIA dataset show that AGDI has better identification and verification performance than GEI. Comparing to PCA, 2DPCA is a more efficient and less memory storage consumption feature extraction method in gait based recognition.
Reynolds averaged simulation of unsteady separated flow
International Nuclear Information System (INIS)
Iaccarino, G.; Ooi, A.; Durbin, P.A.; Behnia, M.
2003-01-01
The accuracy of Reynolds averaged Navier-Stokes (RANS) turbulence models in predicting complex flows with separation is examined. The unsteady flow around square cylinder and over a wall-mounted cube are simulated and compared with experimental data. For the cube case, none of the previously published numerical predictions obtained by steady-state RANS produced a good match with experimental data. However, evidence exists that coherent vortex shedding occurs in this flow. Its presence demands unsteady RANS computation because the flow is not statistically stationary. The present study demonstrates that unsteady RANS does indeed predict periodic shedding, and leads to much better concurrence with available experimental data than has been achieved with steady computation
Angle-averaged Compton cross sections
Energy Technology Data Exchange (ETDEWEB)
Nickel, G.H.
1983-01-01
The scattering of a photon by an individual free electron is characterized by six quantities: ..cap alpha.. = initial photon energy in units of m/sub 0/c/sup 2/; ..cap alpha../sub s/ = scattered photon energy in units of m/sub 0/c/sup 2/; ..beta.. = initial electron velocity in units of c; phi = angle between photon direction and electron direction in the laboratory frame (LF); theta = polar angle change due to Compton scattering, measured in the electron rest frame (ERF); and tau = azimuthal angle change in the ERF. We present an analytic expression for the average of the Compton cross section over phi, theta, and tau. The lowest order approximation to this equation is reasonably accurate for photons and electrons with energies of many keV.
The balanced survivor average causal effect.
Greene, Tom; Joffe, Marshall; Hu, Bo; Li, Liang; Boucher, Ken
2013-05-07
Statistical analysis of longitudinal outcomes is often complicated by the absence of observable values in patients who die prior to their scheduled measurement. In such cases, the longitudinal data are said to be "truncated by death" to emphasize that the longitudinal measurements are not simply missing, but are undefined after death. Recently, the truncation by death problem has been investigated using the framework of principal stratification to define the target estimand as the survivor average causal effect (SACE), which in the context of a two-group randomized clinical trial is the mean difference in the longitudinal outcome between the treatment and control groups for the principal stratum of always-survivors. The SACE is not identified without untestable assumptions. These assumptions have often been formulated in terms of a monotonicity constraint requiring that the treatment does not reduce survival in any patient, in conjunction with assumed values for mean differences in the longitudinal outcome between certain principal strata. In this paper, we introduce an alternative estimand, the balanced-SACE, which is defined as the average causal effect on the longitudinal outcome in a particular subset of the always-survivors that is balanced with respect to the potential survival times under the treatment and control. We propose a simple estimator of the balanced-SACE that compares the longitudinal outcomes between equivalent fractions of the longest surviving patients between the treatment and control groups and does not require a monotonicity assumption. We provide expressions for the large sample bias of the estimator, along with sensitivity analyses and strategies to minimize this bias. We consider statistical inference under a bootstrap resampling procedure.
Averaging processes in granular flows driven by gravity
Rossi, Giulia; Armanini, Aronne
2016-04-01
One of the more promising theoretical frames to analyse the two-phase granular flows is offered by the similarity of their rheology with the kinetic theory of gases [1]. Granular flows can be considered a macroscopic equivalent of the molecular case: the collisions among molecules are compared to the collisions among grains at a macroscopic scale [2,3]. However there are important statistical differences in dealing with the two applications. In the two-phase fluid mechanics, there are two main types of average: the phasic average and the mass weighed average [4]. The kinetic theories assume that the size of atoms is so small, that the number of molecules in a control volume is infinite. With this assumption, the concentration (number of particles n) doesn't change during the averaging process and the two definitions of average coincide. This hypothesis is no more true in granular flows: contrary to gases, the dimension of a single particle becomes comparable to that of the control volume. For this reason, in a single realization the number of grain is constant and the two averages coincide; on the contrary, for more than one realization, n is no more constant and the two types of average lead to different results. Therefore, the ensamble average used in the standard kinetic theory (which usually is the phasic average) is suitable for the single realization, but not for several realization, as already pointed out in [5,6]. In the literature, three main length scales have been identified [7]: the smallest is the particles size, the intermediate consists in the local averaging (in order to describe some instability phenomena or secondary circulation) and the largest arises from phenomena such as large eddies in turbulence. Our aim is to solve the intermediate scale, by applying the mass weighted average, when dealing with more than one realizations. This statistical approach leads to additional diffusive terms in the continuity equation: starting from experimental
New Nordic diet versus average Danish diet
DEFF Research Database (Denmark)
Khakimov, Bekzod; Poulsen, Sanne Kellebjerg; Savorani, Francesco
2016-01-01
and 3-hydroxybutanoic acid were related to a higher weight loss, while higher concentrations of salicylic, lactic and N-aspartic acids, and 1,5-anhydro-D-sorbitol were related to a lower weight loss. Specific gender- and seasonal differences were also observed. The study strongly indicates that healthy...... metabolites reflecting specific differences in the diets, especially intake of plant foods and seafood, and in energy metabolism related to ketone bodies and gluconeogenesis, formed the predominant metabolite pattern discriminating the intervention groups. Among NND subjects higher levels of vaccenic acid...
77 FR 34411 - Branch Technical Position on Concentration Averaging and Encapsulation
2012-06-11
..., ``Licensing Requirements for Land Disposal of Radioactive Waste,'' establishes a waste classification system... Commission paper, SECY-07-0180, ``Strategic Assessment of Low- Level Radioactive Waste Regulatory Program... Requirements Memorandum for SECY-10-0043, ``Blending of Low-Level Radioactive Waste,'' (ADAMS Accession No...
Different parts of soil solution move with different velocities, and therefore chemicals are leached gradually from soil with infiltrating water. Solute dispersivity is the soil parameter characterizing this phenomenon. To characterize the dispersivity of soil profile at field scale, it is desirable...
Industrial Applications of High Average Power FELS
Shinn, Michelle D
2005-01-01
The use of lasers for material processing continues to expand, and the annual sales of such lasers exceeds $1 B (US). Large scale (many m2) processing of materials require the economical production of laser powers of the tens of kilowatts, and therefore are not yet commercial processes, although they have been demonstrated. The development of FELs based on superconducting RF (SRF) linac technology provides a scaleable path to laser outputs above 50 kW in the IR, rendering these applications economically viable, since the cost/photon drops as the output power increases. This approach also enables high average power ~ 1 kW output in the UV spectrum. Such FELs will provide quasi-cw (PRFs in the tens of MHz), of ultrafast (pulsewidth ~ 1 ps) output with very high beam quality. This talk will provide an overview of applications tests by our facility's users such as pulsed laser deposition, laser ablation, and laser surface modification, as well as present plans that will be tested with our upgraded FELs. These upg...
Calculating Free Energies Using Average Force
Darve, Eric; Pohorille, Andrew; DeVincenzi, Donald L. (Technical Monitor)
2001-01-01
A new, general formula that connects the derivatives of the free energy along the selected, generalized coordinates of the system with the instantaneous force acting on these coordinates is derived. The instantaneous force is defined as the force acting on the coordinate of interest so that when it is subtracted from the equations of motion the acceleration along this coordinate is zero. The formula applies to simulations in which the selected coordinates are either unconstrained or constrained to fixed values. It is shown that in the latter case the formula reduces to the expression previously derived by den Otter and Briels. If simulations are carried out without constraining the coordinates of interest, the formula leads to a new method for calculating the free energy changes along these coordinates. This method is tested in two examples - rotation around the C-C bond of 1,2-dichloroethane immersed in water and transfer of fluoromethane across the water-hexane interface. The calculated free energies are compared with those obtained by two commonly used methods. One of them relies on determining the probability density function of finding the system at different values of the selected coordinate and the other requires calculating the average force at discrete locations along this coordinate in a series of constrained simulations. The free energies calculated by these three methods are in excellent agreement. The relative advantages of each method are discussed.
Geographic Gossip: Efficient Averaging for Sensor Networks
Dimakis, Alexandros D. G.; Sarwate, Anand D.; Wainwright, Martin J.
Gossip algorithms for distributed computation are attractive due to their simplicity, distributed nature, and robustness in noisy and uncertain environments. However, using standard gossip algorithms can lead to a significant waste in energy by repeatedly recirculating redundant information. For realistic sensor network model topologies like grids and random geometric graphs, the inefficiency of gossip schemes is related to the slow mixing times of random walks on the communication graph. We propose and analyze an alternative gossiping scheme that exploits geographic information. By utilizing geographic routing combined with a simple resampling method, we demonstrate substantial gains over previously proposed gossip protocols. For regular graphs such as the ring or grid, our algorithm improves standard gossip by factors of $n$ and $\\sqrt{n}$ respectively. For the more challenging case of random geometric graphs, our algorithm computes the true average to accuracy $\\epsilon$ using $O(\\frac{n^{1.5}}{\\sqrt{\\log n}} \\log \\epsilon^{-1})$ radio transmissions, which yields a $\\sqrt{\\frac{n}{\\log n}}$ factor improvement over standard gossip algorithms. We illustrate these theoretical results with experimental comparisons between our algorithm and standard methods as applied to various classes of random fields.
High-average-power solid state lasers
International Nuclear Information System (INIS)
Summers, M.A.
1989-01-01
In 1987, a broad-based, aggressive R ampersand D program aimed at developing the technologies necessary to make possible the use of solid state lasers that are capable of delivering medium- to high-average power in new and demanding applications. Efforts were focused along the following major lines: development of laser and nonlinear optical materials, and of coatings for parasitic suppression and evanescent wave control; development of computational design tools; verification of computational models on thoroughly instrumented test beds; and applications of selected aspects of this technology to specific missions. In the laser materials areas, efforts were directed towards producing strong, low-loss laser glasses and large, high quality garnet crystals. The crystal program consisted of computational and experimental efforts aimed at understanding the physics, thermodynamics, and chemistry of large garnet crystal growth. The laser experimental efforts were directed at understanding thermally induced wave front aberrations in zig-zag slabs, understanding fluid mechanics, heat transfer, and optical interactions in gas-cooled slabs, and conducting critical test-bed experiments with various electro-optic switch geometries. 113 refs., 99 figs., 18 tabs
The concept of average LET values determination
International Nuclear Information System (INIS)
Makarewicz, M.
1981-01-01
The concept of average LET (linear energy transfer) values determination, i.e. ordinary moments of LET in absorbed dose distribution vs. LET of ionizing radiation of any kind and any spectrum (even the unknown ones) has been presented. The method is based on measurement of ionization current with several values of voltage supplying an ionization chamber operating in conditions of columnar recombination of ions or ion recombination in clusters while the chamber is placed in the radiation field at the point of interest. By fitting a suitable algebraic expression to the measured current values one can obtain coefficients of the expression which can be interpreted as values of LET moments. One of the advantages of the method is its experimental and computational simplicity. It has been shown that for numerical estimation of certain effects dependent on LET of radiation it is not necessary to know the dose distribution but only a number of parameters of the distribution, i.e. the LET moments. (author)
On spectral averages in nuclear spectroscopy
International Nuclear Information System (INIS)
Verbaarschot, J.J.M.
1982-01-01
In nuclear spectroscopy one tries to obtain a description of systems of bound nucleons. By means of theoretical models one attemps to reproduce the eigenenergies and the corresponding wave functions which then enable the computation of, for example, the electromagnetic moments and the transition amplitudes. Statistical spectroscopy can be used for studying nuclear systems in large model spaces. In this thesis, methods are developed and applied which enable the determination of quantities in a finite part of the Hilbert space, which is defined by specific quantum values. In the case of averages in a space defined by a partition of the nucleons over the single-particle orbits, the propagation coefficients reduce to Legendre interpolation polynomials. In chapter 1 these polynomials are derived with the help of a generating function and a generalization of Wick's theorem. One can then deduce the centroid and the variance of the eigenvalue distribution in a straightforward way. The results are used to calculate the systematic energy difference between states of even and odd parity for nuclei in the mass region A=10-40. In chapter 2 an efficient method for transforming fixed angular momentum projection traces into fixed angular momentum for the configuration space traces is developed. In chapter 3 it is shown that the secular behaviour can be represented by a Gaussian function of the energies. (Auth.)
Herrmann, Richard A.
1974-01-01
By concentrating radioactivity contained on luminous dials, a teacher can make a high reading source for classroom experiments on radiation. The preparation of the source and its uses are described. (DT)
International Nuclear Information System (INIS)
Dunn, L.F.; Taylor, M.L.; Kron, T.; Franich, R.
2010-01-01
Full text: Anatomic motion during a radiotherapy treatment is one of the more significant challenges in contemporary radiation therapy. For tumours of the lung, motion due to patient respiration makes both accurate planning and dose delivery difficult. One approach is to use the maximum intensity projection (MIP) obtained from a 40 computed tomography (CT) scan and then use this to determine the treatment volume. The treatment is then planned on a 4DCT average reco struction, rather than assuming the entire ITY has a uniform tumour density. This raises the question: how well does planning on a 'blurred' distribution of density with CT values greater than lung density but less than tumour density match the true case of a tumour moving within lung tissue? The aim of this study was to answer this question, determining the dosimetric impact of using a 4D-CT average reconstruction as the basis for a radiotherapy treatment plan. To achieve this, Monte-Carlo sim ulations were undertaken using GEANT4. The geometry consisted of a tumour (diameter 30 mm) moving with a sinusoidal pattern of amplitude = 20 mm. The tumour's excursion occurs within a lung equivalent volume beyond a chest wall interface. Motion was defined parallel to a 6 MY beam. This was then compared to a single oblate tumour of a magnitude determined by the extremes of the tumour motion. The variable density of the 4DCT average tumour is simulated by a time-weighted average, to achieve the observed density gradient. The generic moving tumour geometry is illustrated in the Figure.
RX: a nonimaging concentrator.
Miñano, J C; Benítez, P; González, J C
1995-05-01
A detailed description of the design procedure for a new concentrator, RX, and some examples of it's use are given. The method of design is basically the same as that used in the design of two other concentrators: the RR and the XR [Appl. Opt. 31, 3051 (1992)]. The RX is ideal in two-dimensional geometry. The performance of the rotational RX is good when the average angular spread of the input bundle is small: up to 95% of the power of the input bundle can be transferred to the output bundle (with the assumption of a constant radiance for the rays of the input bundle).
Aarthi, G.; Ramachandra Reddy, G.
2018-03-01
In our paper, the impact of adaptive transmission schemes: (i) optimal rate adaptation (ORA) and (ii) channel inversion with fixed rate (CIFR) on the average spectral efficiency (ASE) are explored for free-space optical (FSO) communications with On-Off Keying (OOK), Polarization shift keying (POLSK), and Coherent optical wireless communication (Coherent OWC) systems under different turbulence regimes. Further to enhance the ASE we have incorporated aperture averaging effects along with the above adaptive schemes. The results indicate that ORA adaptation scheme has the advantage of improving the ASE performance compared with CIFR under moderate and strong turbulence regime. The coherent OWC system with ORA excels the other modulation schemes and could achieve ASE performance of 49.8 bits/s/Hz at the average transmitted optical power of 6 dBm under strong turbulence. By adding aperture averaging effect we could achieve an ASE of 50.5 bits/s/Hz under the same conditions. This makes ORA with Coherent OWC modulation as a favorable candidate for improving the ASE of the FSO communication system.
To quantum averages through asymptotic expansion of classical averages on infinite-dimensional space
International Nuclear Information System (INIS)
Khrennikov, Andrei
2007-01-01
We study asymptotic expansions of Gaussian integrals of analytic functionals on infinite-dimensional spaces (Hilbert and nuclear Frechet). We obtain an asymptotic equality coupling the Gaussian integral and the trace of the composition of scaling of the covariation operator of a Gaussian measure and the second (Frechet) derivative of a functional. In this way we couple classical average (given by an infinite-dimensional Gaussian integral) and quantum average (given by the von Neumann trace formula). We can interpret this mathematical construction as a procedure of 'dequantization' of quantum mechanics. We represent quantum mechanics as an asymptotic projection of classical statistical mechanics with infinite-dimensional phase space. This space can be represented as the space of classical fields, so quantum mechanics is represented as a projection of 'prequantum classical statistical field theory'
Determining average path length and average trapping time on generalized dual dendrimer
Li, Ling; Guan, Jihong
2015-03-01
Dendrimer has wide number of important applications in various fields. In some cases during transport or diffusion process, it transforms into its dual structure named Husimi cactus. In this paper, we study the structure properties and trapping problem on a family of generalized dual dendrimer with arbitrary coordination numbers. We first calculate exactly the average path length (APL) of the networks. The APL increases logarithmically with the network size, indicating that the networks exhibit a small-world effect. Then we determine the average trapping time (ATT) of the trapping process in two cases, i.e., the trap placed on a central node and the trap is uniformly distributed in all the nodes of the network. In both case, we obtain explicit solutions of ATT and show how they vary with the networks size. Besides, we also discuss the influence of the coordination number on trapping efficiency.
20 CFR 404.221 - Computing your average monthly wage.
2010-04-01
... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Computing your average monthly wage. 404.221... DISABILITY INSURANCE (1950- ) Computing Primary Insurance Amounts Average-Monthly-Wage Method of Computing Primary Insurance Amounts § 404.221 Computing your average monthly wage. (a) General. Under the average...
Average and local structure of α-CuI by configurational averaging
International Nuclear Information System (INIS)
Mohn, Chris E; Stoelen, Svein
2007-01-01
Configurational Boltzmann averaging together with density functional theory are used to study in detail the average and local structure of the superionic α-CuI. We find that the coppers are spread out with peaks in the atom-density at the tetrahedral sites of the fcc sublattice of iodines. We calculate Cu-Cu, Cu-I and I-I pair radial distribution functions, the distribution of coordination numbers and the distribution of Cu-I-Cu, I-Cu-I and Cu-Cu-Cu bond-angles. The partial pair distribution functions are in good agreement with experimental neutron diffraction-reverse Monte Carlo, extended x-ray absorption fine structure and ab initio molecular dynamics results. In particular, our results confirm the presence of a prominent peak at around 2.7 A in the Cu-Cu pair distribution function as well as a broader, less intense peak at roughly 4.3 A. We find highly flexible bonds and a range of coordination numbers for both iodines and coppers. This structural flexibility is of key importance in order to understand the exceptional conductivity of coppers in α-CuI; the iodines can easily respond to changes in the local environment as the coppers diffuse, and a myriad of different diffusion-pathways is expected due to the large variation in the local motifs
Sensor-triggered sampling to determine instantaneous airborne vapor exposure concentrations.
Smith, Philip A; Simmons, Michael K; Toone, Phillip
2018-06-01
It is difficult to measure transient airborne exposure peaks by means of integrated sampling for organic chemical vapors, even with very short-duration sampling. Selection of an appropriate time to measure an exposure peak through integrated sampling is problematic, and short-duration time-weighted average (TWA) values obtained with integrated sampling are not likely to accurately determine actual peak concentrations attained when concentrations fluctuate rapidly. Laboratory analysis for integrated exposure samples is preferred from a certainty standpoint over results derived in the field from a sensor, as a sensor user typically must overcome specificity issues and a number of potential interfering factors to obtain similarly reliable data. However, sensors are currently needed to measure intra-exposure period concentration variations (i.e., exposure peaks). In this article, the digitized signal from a photoionization detector (PID) sensor triggered collection of whole-air samples when toluene or trichloroethylene vapors attained pre-determined levels in a laboratory atmosphere generation system. Analysis by gas chromatography-mass spectrometry of whole-air samples (with both 37 and 80% relative humidity) collected using the triggering mechanism with rapidly increasing vapor concentrations showed good agreement with the triggering set point values. Whole-air samples (80% relative humidity) in canisters demonstrated acceptable 17-day storage recoveries, and acceptable precision and bias were obtained. The ability to determine exceedance of a ceiling or peak exposure standard by laboratory analysis of an instantaneously collected sample, and to simultaneously provide a calibration point to verify the correct operation of a sensor was demonstrated. This latter detail may increase the confidence in reliability of sensor data obtained across an entire exposure period.
Directory of Open Access Journals (Sweden)
Jennifer S. Pierce
2015-01-01
Full Text Available Diacetyl, a suspected cause of respiratory disorders in some food and flavorings manufacturing workers, is also a natural component of roasted coffee. We characterized diacetyl exposures that would plausibly occur in a small coffee shop during the preparation and consumption of unflavored coffee. Personal (long- and short-term and area (long-term samples were collected while a barista ground whole coffee beans, and brewed and poured coffee into cups. Simultaneously, long-term personal samples were collected as two participants, the customers, drank one cup of coffee each per h. Air sampling and analyses were conducted in accordance with OSHA Method 1012. Diacetyl was detected in all long-term samples. The long-term concentrations for the barista and area samples were similar, and ranged from 0.013–0.016 ppm; long-term concentrations for the customers were slightly lower and ranged from 0.010–0.014 ppm. Short-term concentrations ranged from below the limit of detection (<0.0047 ppm–0.016 ppm. Mean estimated 8 h time-weighted average (8 h TWA exposures for the barista ranged from 0.007–0.013 ppm; these values exceed recommended 8 h TWA occupational exposure limits (OELs for diacetyl and are comparable to long-term personal measurements collected in various food and beverage production facilities. The concentrations measured based on area sampling were comparable to those measured in the breathing zone of the barista, thus exceedances of the recommended OELs may also occur for coffee shop workers who do not personally prepare coffee (e.g., cashier, sanitation/maintenance. These findings suggest that the practicality and scientific basis of the recommended OELs for diacetyl merit further consideration.
Averaged emission factors for the Hungarian car fleet
Energy Technology Data Exchange (ETDEWEB)
Haszpra, L. [Inst. for Atmospheric Physics, Budapest (Hungary); Szilagyi, I. [Central Research Inst. for Chemistry, Budapest (Hungary)
1995-12-31
The vehicular emission of non-methane hydrocarbon (NMHC) is one of the largest anthropogenic sources of NMHC in Hungary and in most of the industrialized countries. Non-methane hydrocarbon plays key role in the formation of photo-chemical air pollution, usually characterized by the ozone concentration, which seriously endangers the environment and human health. The ozone forming potential of the different NMHCs differs from each other significantly, while the NMHC composition of the car exhaust is influenced by the fuel and engine type, technical condition of the vehicle, vehicle speed and several other factors. In Hungary the majority of the cars are still of Eastern European origin. They represent the technological standard of the 70`s, although there are changes recently. Due to the long-term economical decline in Hungary the average age of the cars was about 9 years in 1990 and reached 10 years by 1993. The condition of the majority of the cars is poor. In addition, almost one third (31.2 %) of the cars are equipped with two-stroke engines which emit less NO{sub x} but much more hydrocarbon. The number of cars equipped with catalytic converter was negligible in 1990 and is slowly increasing only recently. As a consequence of these facts the traffic emission in Hungary may differ from that measured in or estimated for the Western European countries and the differences should be taken into account in the air pollution models. For the estimation of the average emission of the Hungarian car fleet a one-day roadway tunnel experiment was performed in the downtown of Budapest in summer, 1991. (orig.)
Wang, Ling; Abdel-Aty, Mohamed; Wang, Xuesong; Yu, Rongjie
2018-02-01
There have been plenty of traffic safety studies based on average daily traffic (ADT), average hourly traffic (AHT), or microscopic traffic at 5 min intervals. Nevertheless, not enough research has compared the performance of these three types of safety studies, and seldom of previous studies have intended to find whether the results of one type of study is transferable to the other two studies. First, this study built three models: a Bayesian Poisson-lognormal model to estimate the daily crash frequency using ADT, a Bayesian Poisson-lognormal model to estimate the hourly crash frequency using AHT, and a Bayesian logistic regression model for the real-time safety analysis using microscopic traffic. The model results showed that the crash contributing factors found by different models were comparable but not the same. Four variables, i.e., the logarithm of volume, the standard deviation of speed, the logarithm of segment length, and the existence of diverge segment, were positively significant in the three models. Additionally, weaving segments experienced higher daily and hourly crash frequencies than merge and basic segments. Then, each of the ADT-based, AHT-based, and real-time models was used to estimate safety conditions at different levels: daily and hourly, meanwhile, the real-time model was also used in 5 min intervals. The results uncovered that the ADT- and AHT-based safety models performed similar in predicting daily and hourly crash frequencies, and the real-time safety model was able to provide hourly crash frequency. Copyright © 2017 Elsevier Ltd. All rights reserved.
Nonimaging concentrators for diode-pumped slab lasers
Lacovara, Philip; Gleckman, Philip L.; Holman, Robert L.; Winston, Roland
1991-10-01
Diode-pumped slab lasers require concentrators for high-average power operation. We detail the properties of diode lasers and slab lasers which set the concentration requirements and the concentrator design methodologies that are used, and describe some concentrator designs used in high-average power slab lasers at Lincoln Laboratory.
Distribution of exposure concentrations and doses for constituents of environmental tobacco smoke
Energy Technology Data Exchange (ETDEWEB)
LaKind, J.S. [LaKind Associates (United States); Ginevan, M.E. [M.E. Ginevan and Associates (United States); Naiman, D.Q. [Johns Hopkins Univ., Baltimore, MD (United States). Dept. of Mathematical Sciences; James, A.C. [A.C. James and Associates (United States); Jenkins, R.A. [Oak Ridge National Lab., TN (United States); Dourson, M.L.; Felter, S.P. [TERA (United States); Graves, C.G.; Tardiff, R.G. [Sapphire Group, Inc., Bethesda, MD (United States)
1999-06-01
The ultimate goal of the research reported in this series of three articles is to derive distributions of doses of selected environmental tobacco smoke (ETS)-related chemicals for nonsmoking workers. This analysis uses data from the 16-City Study collected with personal monitors over the course of one workday in workplaces where smoking occurred. In this article, the authors describe distributions of ETS chemical concentrations and the characteristics of those distributions for the workplace exposure. Next, they present population parameters relevant for estimating dose distributions and the methods used for estimating those dose distributions. Finally, they derive distributions of doses of selected ETS-related constituents obtained in the workplace for people in smoking work environments. Estimating dose distributions provided information beyond the usual point estimate of dose and showed that the preponderance of individuals exposed to ETS in the workplace were exposed at the low end of the dose distribution curve. The results of this analysis include estimations of hourly maxima and time-weighted average (TWA) doses of nicotine from workplace exposures to ETS and doses derived from modeled lung burdens of ultraviolet-absorbing particulate matter (UVPM) and solanesol resulting from workplace exposures to ETS (extrapolated from 1 day to 1 year).
Analytical expressions for conditional averages: A numerical test
DEFF Research Database (Denmark)
Pécseli, H.L.; Trulsen, J.
1991-01-01
Conditionally averaged random potential fluctuations are an important quantity for analyzing turbulent electrostatic plasma fluctuations. Experimentally, this averaging can be readily performed by sampling the fluctuations only when a certain condition is fulfilled at a reference position...
Experimental demonstration of squeezed-state quantum averaging
DEFF Research Database (Denmark)
Lassen, Mikael Østergaard; Madsen, Lars Skovgaard; Sabuncu, Metin
2010-01-01
We propose and experimentally demonstrate a universal quantum averaging process implementing the harmonic mean of quadrature variances. The averaged variances are prepared probabilistically by means of linear optical interference and measurement-induced conditioning. We verify that the implemented...
International Nuclear Information System (INIS)
Kousa, A.; Rotko, T.; Alm, S.; Monn, C.
2001-01-01
Personal exposures, residential indoor, outdoor and workplace levels of nitrogen dioxide (NO 2 ) were measured for 262 urban adult (25-55 years) participants in three EXPOLIS centres (Basel, Switzerland; Helsinki, Finland; and Prague, Czech Republic) using passive samplers for 48-h sampling periods during 1996-1997. The average residential outdoor and indoor NO 2 levels were lowest in Helsinki (24 ± 12 and 18 ± 11 μgm -3 , respectively), highest in Prague (61 ± 20 and 43 ± 23μgm -3 ), with Basel in between (36 ± 13 and 27± 13μgm -3 ). Average workplace NO 2 levels, however, were highest in Basel (36 ± 24μgm -3 ), lowest in Helsinki (27 ± 15μgm -3 ), with Prague in between (30 ± 18μgm -3 ). A time-weighted microenvironmental exposure model explained 74% of the personal exposure variation in all centre and in average 88% of the exposures. Log-linear regression models, using residential outdoor measurements (fixed site monitoring) combined with residential and work characteristics (i.e. work location, using gas appliances and keeping windows open), explained 48% (37%) of the personal NO 2 exposure variation. Regression models based on ambient fixed site concentrations alone explained only 11-19% of personal NO 2 exposure variation. Thus, ambient fixed site monitoring alone was a poor predictor for personal NO 2 exposure variation, but adding personal questionnaire information can significantly improve the predicting power. (Author)
Tecpoyotl-Torres, M.; Campos-Alvarez, J.; Tellez-Alanis, F.; Sánchez-Mondragón, J.
2006-08-01
In this work we present the basis of the solar concentrator design, which has is located at Temixco, Morelos, Mexico. For this purpose, this place is ideal due to its geographic and climatic conditions, and in addition, because it accounts with the greatest constant illumination in Mexico. For the construction of the concentrator we use a recycled parabolic plate of a telecommunications satellite dish (NEC). This plate was totally covered with Aluminum. The opening diameter is of 332 cm, the focal length is of 83 cm and the opening angle is of 90°. The geometry of the plate guaranties that the incident beams, will be collected at the focus. The mechanical treatment of the plate produces an average reflectance of 75% in the visible region of the solar spectrum, and of 92% for wavelengths up to 3μm in the infrared region. We obtain up to 2000°C of temperature concentration with this setup. The reflectance can be greatly improved, but did not consider it as typical practical use. The energy obtained can be applied to conditions that require of those high calorific energies. In order to optimize the operation of the concentrator we use a control circuit designed to track the apparent sun position.
The flattening of the average potential in models with fermions
International Nuclear Information System (INIS)
Bornholdt, S.
1993-01-01
The average potential is a scale dependent scalar effective potential. In a phase with spontaneous symmetry breaking its inner region becomes flat as the averaging extends over infinite volume and the average potential approaches the convex effective potential. Fermion fluctuations affect the shape of the average potential in this region and its flattening with decreasing physical scale. They have to be taken into account to find the true minimum of the scalar potential which determines the scale of spontaneous symmetry breaking. (orig.)
20 CFR 404.220 - Average-monthly-wage method.
2010-04-01
... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Average-monthly-wage method. 404.220 Section... INSURANCE (1950- ) Computing Primary Insurance Amounts Average-Monthly-Wage Method of Computing Primary Insurance Amounts § 404.220 Average-monthly-wage method. (a) Who is eligible for this method. You must...
A time-averaged cosmic ray propagation theory
International Nuclear Information System (INIS)
Klimas, A.J.
1975-01-01
An argument is presented, which casts doubt on our ability to choose an appropriate magnetic field ensemble for computing the average behavior of cosmic ray particles. An alternate procedure, using time-averages rather than ensemble-averages, is presented. (orig.) [de
7 CFR 51.2561 - Average moisture content.
2010-01-01
... 7 Agriculture 2 2010-01-01 2010-01-01 false Average moisture content. 51.2561 Section 51.2561... STANDARDS) United States Standards for Grades of Shelled Pistachio Nuts § 51.2561 Average moisture content. (a) Determining average moisture content of the lot is not a requirement of the grades, except when...
Averaging in SU(2) open quantum random walk
International Nuclear Information System (INIS)
Ampadu Clement
2014-01-01
We study the average position and the symmetry of the distribution in the SU(2) open quantum random walk (OQRW). We show that the average position in the central limit theorem (CLT) is non-uniform compared with the average position in the non-CLT. The symmetry of distribution is shown to be even in the CLT
Averaging in SU(2) open quantum random walk
Clement, Ampadu
2014-03-01
We study the average position and the symmetry of the distribution in the SU(2) open quantum random walk (OQRW). We show that the average position in the central limit theorem (CLT) is non-uniform compared with the average position in the non-CLT. The symmetry of distribution is shown to be even in the CLT.
Averaging and sampling for magnetic-observatory hourly data
Directory of Open Access Journals (Sweden)
J. J. Love
2010-11-01
Full Text Available A time and frequency-domain analysis is made of the effects of averaging and sampling methods used for constructing magnetic-observatory hourly data values. Using 1-min data as a proxy for continuous, geomagnetic variation, we construct synthetic hourly values of two standard types: instantaneous "spot" measurements and simple 1-h "boxcar" averages. We compare these average-sample types with others: 2-h average, Gaussian, and "brick-wall" low-frequency-pass. Hourly spot measurements provide a statistically unbiased representation of the amplitude range of geomagnetic-field variation, but as a representation of continuous field variation over time, they are significantly affected by aliasing, especially at high latitudes. The 1-h, 2-h, and Gaussian average-samples are affected by a combination of amplitude distortion and aliasing. Brick-wall values are not affected by either amplitude distortion or aliasing, but constructing them is, in an operational setting, relatively more difficult than it is for other average-sample types. It is noteworthy that 1-h average-samples, the present standard for observatory hourly data, have properties similar to Gaussian average-samples that have been optimized for a minimum residual sum of amplitude distortion and aliasing. For 1-h average-samples from medium and low-latitude observatories, the average of the combination of amplitude distortion and aliasing is less than the 5.0 nT accuracy standard established by Intermagnet for modern 1-min data. For medium and low-latitude observatories, average differences between monthly means constructed from 1-min data and monthly means constructed from any of the hourly average-sample types considered here are less than the 1.0 nT resolution of standard databases. We recommend that observatories and World Data Centers continue the standard practice of reporting simple 1-h-average hourly values.
Safety Impact of Average Speed Control in the UK
DEFF Research Database (Denmark)
Lahrmann, Harry Spaabæk; Brassøe, Bo; Johansen, Jonas Wibert
2016-01-01
of automatic speed control was point-based, but in recent years a potentially more effective alternative automatic speed control method has been introduced. This method is based upon records of drivers’ average travel speed over selected sections of the road and is normally called average speed control...... in the UK. The study demonstrates that the introduction of average speed control results in statistically significant and substantial reductions both in speed and in number of accidents. The evaluation indicates that average speed control has a higher safety effect than point-based automatic speed control....
on the performance of Autoregressive Moving Average Polynomial
African Journals Online (AJOL)
Timothy Ademakinwa
Distributed Lag (PDL) model, Autoregressive Polynomial Distributed Lag ... Moving Average Polynomial Distributed Lag (ARMAPDL) model. ..... Global Journal of Mathematics and Statistics. Vol. 1. ... Business and Economic Research Center.
Decision trees with minimum average depth for sorting eight elements
AbouEisha, Hassan M.
2015-11-19
We prove that the minimum average depth of a decision tree for sorting 8 pairwise different elements is equal to 620160/8!. We show also that each decision tree for sorting 8 elements, which has minimum average depth (the number of such trees is approximately equal to 8.548×10^326365), has also minimum depth. Both problems were considered by Knuth (1998). To obtain these results, we use tools based on extensions of dynamic programming which allow us to make sequential optimization of decision trees relative to depth and average depth, and to count the number of decision trees with minimum average depth.
Comparison of Interpolation Methods as Applied to Time Synchronous Averaging
National Research Council Canada - National Science Library
Decker, Harry
1999-01-01
Several interpolation techniques were investigated to determine their effect on time synchronous averaging of gear vibration signals and also the effects on standard health monitoring diagnostic parameters...
Light-cone averaging in cosmology: formalism and applications
International Nuclear Information System (INIS)
Gasperini, M.; Marozzi, G.; Veneziano, G.; Nugier, F.
2011-01-01
We present a general gauge invariant formalism for defining cosmological averages that are relevant for observations based on light-like signals. Such averages involve either null hypersurfaces corresponding to a family of past light-cones or compact surfaces given by their intersection with timelike hypersurfaces. Generalized Buchert-Ehlers commutation rules for derivatives of these light-cone averages are given. After introducing some adapted ''geodesic light-cone'' coordinates, we give explicit expressions for averaging the redshift to luminosity-distance relation and the so-called ''redshift drift'' in a generic inhomogeneous Universe
Directory of Open Access Journals (Sweden)
Aneta Rita Borkowska
2014-05-01
Full Text Available BACKGROUND The aim of the research was to assess memorization and recall of logically connected and unconnected material, coded graphically and linguistically, and the ability to focus attention, in a group of children with intelligence below average, compared to children with average intelligence. PARTICIPANTS AND PROCEDURE The study group included 27 children with intelligence below average. The control group consisted of 29 individuals. All of them were examined using the authors’ experimental trials and the TUS test (Attention and Perceptiveness Test. RESULTS Children with intelligence below average memorized significantly less information contained in the logical material, demonstrated lower ability to memorize the visual material, memorized significantly fewer words in the verbal material learning task, achieved lower results in such indicators of the visual attention process pace as the number of omissions and mistakes, and had a lower pace of perceptual work, compared to children with average intelligence. CONCLUSIONS The results confirm that children with intelligence below average have difficulties with memorizing new material, both logically connected and unconnected. The significantly lower capacity of direct memory is independent of modality. The results of the study on the memory process confirm the hypothesis about lower abilities of children with intelligence below average, in terms of concentration, work pace, efficiency and perception.
Delineation of facial archetypes by 3d averaging.
Shaweesh, Ashraf I; Thomas, C David L; Bankier, Agnes; Clement, John G
2004-10-01
The objective of this study was to investigate the feasibility of creating archetypal 3D faces through computerized 3D facial averaging. A 3D surface scanner Fiore and its software were used to acquire the 3D scans of the faces while 3D Rugle3 and locally-developed software generated the holistic facial averages. 3D facial averages were created from two ethnic groups; European and Japanese and from children with three previous genetic disorders; Williams syndrome, achondroplasia and Sotos syndrome as well as the normal control group. The method included averaging the corresponding depth (z) coordinates of the 3D facial scans. Compared with other face averaging techniques there was not any warping or filling in the spaces by interpolation; however, this facial average lacked colour information. The results showed that as few as 14 faces were sufficient to create an archetypal facial average. In turn this would make it practical to use face averaging as an identification tool in cases where it would be difficult to recruit a larger number of participants. In generating the average, correcting for size differences among faces was shown to adjust the average outlines of the facial features. It is assumed that 3D facial averaging would help in the identification of the ethnic status of persons whose identity may not be known with certainty. In clinical medicine, it would have a great potential for the diagnosis of syndromes with distinctive facial features. The system would also assist in the education of clinicians in the recognition and identification of such syndromes.
Interpreting Bivariate Regression Coefficients: Going beyond the Average
Halcoussis, Dennis; Phillips, G. Michael
2010-01-01
Statistics, econometrics, investment analysis, and data analysis classes often review the calculation of several types of averages, including the arithmetic mean, geometric mean, harmonic mean, and various weighted averages. This note shows how each of these can be computed using a basic regression framework. By recognizing when a regression model…
Average stress in a Stokes suspension of disks
Prosperetti, Andrea
2004-01-01
The ensemble-average velocity and pressure in an unbounded quasi-random suspension of disks (or aligned cylinders) are calculated in terms of average multipoles allowing for the possibility of spatial nonuniformities in the system. An expression for the stress due to the suspended particles is
47 CFR 1.959 - Computation of average terrain elevation.
2010-10-01
... 47 Telecommunication 1 2010-10-01 2010-10-01 false Computation of average terrain elevation. 1.959 Section 1.959 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL PRACTICE AND PROCEDURE Wireless Radio Services Applications and Proceedings Application Requirements and Procedures § 1.959 Computation of average terrain elevation. Except a...
47 CFR 80.759 - Average terrain elevation.
2010-10-01
... 47 Telecommunication 5 2010-10-01 2010-10-01 false Average terrain elevation. 80.759 Section 80.759 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES STATIONS IN THE MARITIME SERVICES Standards for Computing Public Coast Station VHF Coverage § 80.759 Average terrain elevation. (a)(1) Draw radials...
The average covering tree value for directed graph games
Khmelnitskaya, Anna Borisovna; Selcuk, Özer; Talman, Dolf
We introduce a single-valued solution concept, the so-called average covering tree value, for the class of transferable utility games with limited communication structure represented by a directed graph. The solution is the average of the marginal contribution vectors corresponding to all covering
The Average Covering Tree Value for Directed Graph Games
Khmelnitskaya, A.; Selcuk, O.; Talman, A.J.J.
2012-01-01
Abstract: We introduce a single-valued solution concept, the so-called average covering tree value, for the class of transferable utility games with limited communication structure represented by a directed graph. The solution is the average of the marginal contribution vectors corresponding to all
18 CFR 301.7 - Average System Cost methodology functionalization.
2010-04-01
... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Average System Cost... REGULATORY COMMISSION, DEPARTMENT OF ENERGY REGULATIONS FOR FEDERAL POWER MARKETING ADMINISTRATIONS AVERAGE SYSTEM COST METHODOLOGY FOR SALES FROM UTILITIES TO BONNEVILLE POWER ADMINISTRATION UNDER NORTHWEST POWER...
Analytic computation of average energy of neutrons inducing fission
International Nuclear Information System (INIS)
Clark, Alexander Rich
2016-01-01
The objective of this report is to describe how I analytically computed the average energy of neutrons that induce fission in the bare BeRP ball. The motivation of this report is to resolve a discrepancy between the average energy computed via the FMULT and F4/FM cards in MCNP6 by comparison to the analytic results.
An alternative scheme of the Bogolyubov's average method
International Nuclear Information System (INIS)
Ortiz Peralta, T.; Ondarza R, R.; Camps C, E.
1990-01-01
In this paper the average energy and the magnetic moment conservation laws in the Drift Theory of charged particle motion are obtained in a simple way. The approach starts from the energy and magnetic moment conservation laws and afterwards the average is performed. This scheme is more economic from the standpoint of time and algebraic calculations than the usual procedure of Bogolyubov's method. (Author)
Decision trees with minimum average depth for sorting eight elements
AbouEisha, Hassan M.; Chikalov, Igor; Moshkov, Mikhail
2015-01-01
We prove that the minimum average depth of a decision tree for sorting 8 pairwise different elements is equal to 620160/8!. We show also that each decision tree for sorting 8 elements, which has minimum average depth (the number of such trees
Bounds on Average Time Complexity of Decision Trees
Chikalov, Igor
2011-01-01
In this chapter, bounds on the average depth and the average weighted depth of decision trees are considered. Similar problems are studied in search theory [1], coding theory [77], design and analysis of algorithms (e.g., sorting) [38]. For any
A Statistical Mechanics Approach to Approximate Analytical Bootstrap Averages
DEFF Research Database (Denmark)
Malzahn, Dorthe; Opper, Manfred
2003-01-01
We apply the replica method of Statistical Physics combined with a variational method to the approximate analytical computation of bootstrap averages for estimating the generalization error. We demonstrate our approach on regression with Gaussian processes and compare our results with averages...
Self-similarity of higher-order moving averages
Arianos, Sergio; Carbone, Anna; Türk, Christian
2011-10-01
In this work, higher-order moving average polynomials are defined by straightforward generalization of the standard moving average. The self-similarity of the polynomials is analyzed for fractional Brownian series and quantified in terms of the Hurst exponent H by using the detrending moving average method. We prove that the exponent H of the fractional Brownian series and of the detrending moving average variance asymptotically agree for the first-order polynomial. Such asymptotic values are compared with the results obtained by the simulations. The higher-order polynomials correspond to trend estimates at shorter time scales as the degree of the polynomial increases. Importantly, the increase of polynomial degree does not require to change the moving average window. Thus trends at different time scales can be obtained on data sets with the same size. These polynomials could be interesting for those applications relying on trend estimates over different time horizons (financial markets) or on filtering at different frequencies (image analysis).
Anomalous behavior of q-averages in nonextensive statistical mechanics
International Nuclear Information System (INIS)
Abe, Sumiyoshi
2009-01-01
A generalized definition of average, termed the q-average, is widely employed in the field of nonextensive statistical mechanics. Recently, it has however been pointed out that such an average value may behave unphysically under specific deformations of probability distributions. Here, the following three issues are discussed and clarified. Firstly, the deformations considered are physical and may be realized experimentally. Secondly, in view of the thermostatistics, the q-average is unstable in both finite and infinite discrete systems. Thirdly, a naive generalization of the discussion to continuous systems misses a point, and a norm better than the L 1 -norm should be employed for measuring the distance between two probability distributions. Consequently, stability of the q-average is shown not to be established in all of the cases
Bootstrapping pre-averaged realized volatility under market microstructure noise
DEFF Research Database (Denmark)
Hounyo, Ulrich; Goncalves, Sílvia; Meddahi, Nour
The main contribution of this paper is to propose a bootstrap method for inference on integrated volatility based on the pre-averaging approach of Jacod et al. (2009), where the pre-averaging is done over all possible overlapping blocks of consecutive observations. The overlapping nature of the pre......-averaged returns implies that these are kn-dependent with kn growing slowly with the sample size n. This motivates the application of a blockwise bootstrap method. We show that the "blocks of blocks" bootstrap method suggested by Politis and Romano (1992) (and further studied by Bühlmann and Künsch (1995......)) is valid only when volatility is constant. The failure of the blocks of blocks bootstrap is due to the heterogeneity of the squared pre-averaged returns when volatility is stochastic. To preserve both the dependence and the heterogeneity of squared pre-averaged returns, we propose a novel procedure...
Bounds on Average Time Complexity of Decision Trees
Chikalov, Igor
2011-01-01
In this chapter, bounds on the average depth and the average weighted depth of decision trees are considered. Similar problems are studied in search theory [1], coding theory [77], design and analysis of algorithms (e.g., sorting) [38]. For any diagnostic problem, the minimum average depth of decision tree is bounded from below by the entropy of probability distribution (with a multiplier 1/log2 k for a problem over a k-valued information system). Among diagnostic problems, the problems with a complete set of attributes have the lowest minimum average depth of decision trees (e.g, the problem of building optimal prefix code [1] and a blood test study in assumption that exactly one patient is ill [23]). For such problems, the minimum average depth of decision tree exceeds the lower bound by at most one. The minimum average depth reaches the maximum on the problems in which each attribute is "indispensable" [44] (e.g., a diagnostic problem with n attributes and kn pairwise different rows in the decision table and the problem of implementing the modulo 2 summation function). These problems have the minimum average depth of decision tree equal to the number of attributes in the problem description. © Springer-Verlag Berlin Heidelberg 2011.
2010-07-01
... volume of gasoline produced or imported in batch i. Si=The sulfur content of batch i determined under § 80.330. n=The number of batches of gasoline produced or imported during the averaging period. i=Individual batch of gasoline produced or imported during the averaging period. (b) All annual refinery or...
2010-07-01
... and average carbon-related exhaust emissions. 600.510-12 Section 600.510-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF... Transportation. (iv) [Reserved] (2) Average carbon-related exhaust emissions will be calculated to the nearest...
Average inactivity time model, associated orderings and reliability properties
Kayid, M.; Izadkhah, S.; Abouammoh, A. M.
2018-02-01
In this paper, we introduce and study a new model called 'average inactivity time model'. This new model is specifically applicable to handle the heterogeneity of the time of the failure of a system in which some inactive items exist. We provide some bounds for the mean average inactivity time of a lifespan unit. In addition, we discuss some dependence structures between the average variable and the mixing variable in the model when original random variable possesses some aging behaviors. Based on the conception of the new model, we introduce and study a new stochastic order. Finally, to illustrate the concept of the model, some interesting reliability problems are reserved.
Average L-shell fluorescence, Auger, and electron yields
International Nuclear Information System (INIS)
Krause, M.O.
1980-01-01
The dependence of the average L-shell fluorescence and Auger yields on the initial vacancy distribution is shown to be small. By contrast, the average electron yield pertaining to both Auger and Coster-Kronig transitions is shown to display a strong dependence. Numerical examples are given on the basis of Krause's evaluation of subshell radiative and radiationless yields. Average yields are calculated for widely differing vacancy distributions and are intercompared graphically for 40 3 subshell yields in most cases of inner-shell ionization
Simultaneous inference for model averaging of derived parameters
DEFF Research Database (Denmark)
Jensen, Signe Marie; Ritz, Christian
2015-01-01
Model averaging is a useful approach for capturing uncertainty due to model selection. Currently, this uncertainty is often quantified by means of approximations that do not easily extend to simultaneous inference. Moreover, in practice there is a need for both model averaging and simultaneous...... inference for derived parameters calculated in an after-fitting step. We propose a method for obtaining asymptotically correct standard errors for one or several model-averaged estimates of derived parameters and for obtaining simultaneous confidence intervals that asymptotically control the family...
Salecker-Wigner-Peres clock and average tunneling times
International Nuclear Information System (INIS)
Lunardi, Jose T.; Manzoni, Luiz A.; Nystrom, Andrew T.
2011-01-01
The quantum clock of Salecker-Wigner-Peres is used, by performing a post-selection of the final state, to obtain average transmission and reflection times associated to the scattering of localized wave packets by static potentials in one dimension. The behavior of these average times is studied for a Gaussian wave packet, centered around a tunneling wave number, incident on a rectangular barrier and, in particular, on a double delta barrier potential. The regime of opaque barriers is investigated and the results show that the average transmission time does not saturate, showing no evidence of the Hartman effect (or its generalized version).
Time average vibration fringe analysis using Hilbert transformation
International Nuclear Information System (INIS)
Kumar, Upputuri Paul; Mohan, Nandigana Krishna; Kothiyal, Mahendra Prasad
2010-01-01
Quantitative phase information from a single interferogram can be obtained using the Hilbert transform (HT). We have applied the HT method for quantitative evaluation of Bessel fringes obtained in time average TV holography. The method requires only one fringe pattern for the extraction of vibration amplitude and reduces the complexity in quantifying the data experienced in the time average reference bias modulation method, which uses multiple fringe frames. The technique is demonstrated for the measurement of out-of-plane vibration amplitude on a small scale specimen using a time average microscopic TV holography system.
Average multiplications in deep inelastic processes and their interpretation
International Nuclear Information System (INIS)
Kiselev, A.V.; Petrov, V.A.
1983-01-01
Inclusive production of hadrons in deep inelastic proceseseus is considered. It is shown that at high energies the jet evolution in deep inelastic processes is mainly of nonperturbative character. With the increase of a final hadron state energy the leading contribution to an average multiplicity comes from a parton subprocess due to production of massive quark and gluon jets and their further fragmentation as diquark contribution becomes less and less essential. The ratio of the total average multiplicity in deep inelastic processes to the average multiplicity in e + e - -annihilation at high energies tends to unity
Fitting a function to time-dependent ensemble averaged data
DEFF Research Database (Denmark)
Fogelmark, Karl; Lomholt, Michael A.; Irbäck, Anders
2018-01-01
Time-dependent ensemble averages, i.e., trajectory-based averages of some observable, are of importance in many fields of science. A crucial objective when interpreting such data is to fit these averages (for instance, squared displacements) with a function and extract parameters (such as diffusion...... method, weighted least squares including correlation in error estimation (WLS-ICE), to particle tracking data. The WLS-ICE method is applicable to arbitrary fit functions, and we provide a publically available WLS-ICE software....
Average wind statistics for SRP area meteorological towers
International Nuclear Information System (INIS)
Laurinat, J.E.
1987-01-01
A quality assured set of average wind Statistics for the seven SRP area meteorological towers has been calculated for the five-year period 1982--1986 at the request of DOE/SR. A Similar set of statistics was previously compiled for the years 1975-- 1979. The updated wind statistics will replace the old statistics as the meteorological input for calculating atmospheric radionuclide doses from stack releases, and will be used in the annual environmental report. This report details the methods used to average the wind statistics and to screen out bad measurements and presents wind roses generated by the averaged statistics
Average monthly and annual climate maps for Bolivia
Vicente-Serrano, Sergio M.
2015-02-24
This study presents monthly and annual climate maps for relevant hydroclimatic variables in Bolivia. We used the most complete network of precipitation and temperature stations available in Bolivia, which passed a careful quality control and temporal homogenization procedure. Monthly average maps at the spatial resolution of 1 km were modeled by means of a regression-based approach using topographic and geographic variables as predictors. The monthly average maximum and minimum temperatures, precipitation and potential exoatmospheric solar radiation under clear sky conditions are used to estimate the monthly average atmospheric evaporative demand by means of the Hargreaves model. Finally, the average water balance is estimated on a monthly and annual scale for each 1 km cell by means of the difference between precipitation and atmospheric evaporative demand. The digital layers used to create the maps are available in the digital repository of the Spanish National Research Council.
Medicare Part B Drug Average Sales Pricing Files
U.S. Department of Health & Human Services — Manufacturer reporting of Average Sales Price (ASP) data - A manufacturers ASP must be calculated by the manufacturer every calendar quarter and submitted to CMS...
High Average Power Fiber Laser for Satellite Communications, Phase I
National Aeronautics and Space Administration — Very high average power lasers with high electrical-top-optical (E-O) efficiency, which also support pulse position modulation (PPM) formats in the MHz-data rate...
A time averaged background compensator for Geiger-Mueller counters
International Nuclear Information System (INIS)
Bhattacharya, R.C.; Ghosh, P.K.
1983-01-01
The GM tube compensator described stores background counts to cancel an equal number of pulses from the measuring channel providing time averaged compensation. The method suits portable instruments. (orig.)
Time averaging, ageing and delay analysis of financial time series
Cherstvy, Andrey G.; Vinod, Deepak; Aghion, Erez; Chechkin, Aleksei V.; Metzler, Ralf
2017-06-01
We introduce three strategies for the analysis of financial time series based on time averaged observables. These comprise the time averaged mean squared displacement (MSD) as well as the ageing and delay time methods for varying fractions of the financial time series. We explore these concepts via statistical analysis of historic time series for several Dow Jones Industrial indices for the period from the 1960s to 2015. Remarkably, we discover a simple universal law for the delay time averaged MSD. The observed features of the financial time series dynamics agree well with our analytical results for the time averaged measurables for geometric Brownian motion, underlying the famed Black-Scholes-Merton model. The concepts we promote here are shown to be useful for financial data analysis and enable one to unveil new universal features of stock market dynamics.
Historical Data for Average Processing Time Until Hearing Held
Social Security Administration — This dataset provides historical data for average wait time (in days) from the hearing request date until a hearing was held. This dataset includes data from fiscal...
GIS Tools to Estimate Average Annual Daily Traffic
2012-06-01
This project presents five tools that were created for a geographical information system to estimate Annual Average Daily : Traffic using linear regression. Three of the tools can be used to prepare spatial data for linear regression. One tool can be...
A high speed digital signal averager for pulsed NMR
International Nuclear Information System (INIS)
Srinivasan, R.; Ramakrishna, J.; Ra agopalan, S.R.
1978-01-01
A 256-channel digital signal averager suitable for pulsed nuclear magnetic resonance spectroscopy is described. It implements 'stable averaging' algorithm and hence provides a calibrated display of the average signal at all times during the averaging process on a CRT. It has a maximum sampling rate of 2.5 μ sec and a memory capacity of 256 x 12 bit words. Number of sweeps is selectable through a front panel control in binary steps from 2 3 to 2 12 . The enhanced signal can be displayed either on a CRT or by a 3.5-digit LED display. The maximum S/N improvement that can be achieved with this instrument is 36 dB. (auth.)
The average-shadowing property and topological ergodicity for flows
International Nuclear Information System (INIS)
Gu Rongbao; Guo Wenjing
2005-01-01
In this paper, the transitive property for a flow without sensitive dependence on initial conditions is studied and it is shown that a Lyapunov stable flow with the average-shadowing property on a compact metric space is topologically ergodic
Application of Bayesian approach to estimate average level spacing
International Nuclear Information System (INIS)
Huang Zhongfu; Zhao Zhixiang
1991-01-01
A method to estimate average level spacing from a set of resolved resonance parameters by using Bayesian approach is given. Using the information given in the distributions of both levels spacing and neutron width, the level missing in measured sample can be corrected more precisely so that better estimate for average level spacing can be obtained by this method. The calculation of s-wave resonance has been done and comparison with other work was carried out
Annual average equivalent dose of workers form health area
International Nuclear Information System (INIS)
Daltro, T.F.L.; Campos, L.L.
1992-01-01
The data of personnel monitoring during 1985 and 1991 of personnel that work in health area were studied, obtaining a general overview of the value change of annual average equivalent dose. Two different aspects were presented: the analysis of annual average equivalent dose in the different sectors of a hospital and the comparison of these doses in the same sectors in different hospitals. (C.G.C.)
A precise measurement of the average b hadron lifetime
Buskulic, Damir; De Bonis, I; Décamp, D; Ghez, P; Goy, C; Lees, J P; Lucotte, A; Minard, M N; Odier, P; Pietrzyk, B; Ariztizabal, F; Chmeissani, M; Crespo, J M; Efthymiopoulos, I; Fernández, E; Fernández-Bosman, M; Gaitan, V; Garrido, L; Martínez, M; Orteu, S; Pacheco, A; Padilla, C; Palla, Fabrizio; Pascual, A; Perlas, J A; Sánchez, F; Teubert, F; Colaleo, A; Creanza, D; De Palma, M; Farilla, A; Gelao, G; Girone, M; Iaselli, Giuseppe; Maggi, G; Maggi, M; Marinelli, N; Natali, S; Nuzzo, S; Ranieri, A; Raso, G; Romano, F; Ruggieri, F; Selvaggi, G; Silvestris, L; Tempesta, P; Zito, G; Huang, X; Lin, J; Ouyang, Q; Wang, T; Xie, Y; Xu, R; Xue, S; Zhang, J; Zhang, L; Zhao, W; Bonvicini, G; Cattaneo, M; Comas, P; Coyle, P; Drevermann, H; Engelhardt, A; Forty, Roger W; Frank, M; Hagelberg, R; Harvey, J; Jacobsen, R; Janot, P; Jost, B; Knobloch, J; Lehraus, Ivan; Markou, C; Martin, E B; Mato, P; Meinhard, H; Minten, Adolf G; Miquel, R; Oest, T; Palazzi, P; Pater, J R; Pusztaszeri, J F; Ranjard, F; Rensing, P E; Rolandi, Luigi; Schlatter, W D; Schmelling, M; Schneider, O; Tejessy, W; Tomalin, I R; Venturi, A; Wachsmuth, H W; Wiedenmann, W; Wildish, T; Witzeling, W; Wotschack, J; Ajaltouni, Ziad J; Bardadin-Otwinowska, Maria; Barrès, A; Boyer, C; Falvard, A; Gay, P; Guicheney, C; Henrard, P; Jousset, J; Michel, B; Monteil, S; Montret, J C; Pallin, D; Perret, P; Podlyski, F; Proriol, J; Rossignol, J M; Saadi, F; Fearnley, Tom; Hansen, J B; Hansen, J D; Hansen, J R; Hansen, P H; Nilsson, B S; Kyriakis, A; Simopoulou, Errietta; Siotis, I; Vayaki, Anna; Zachariadou, K; Blondel, A; Bonneaud, G R; Brient, J C; Bourdon, P; Passalacqua, L; Rougé, A; Rumpf, M; Tanaka, R; Valassi, Andrea; Verderi, M; Videau, H L; Candlin, D J; Parsons, M I; Focardi, E; Parrini, G; Corden, M; Delfino, M C; Georgiopoulos, C H; Jaffe, D E; Antonelli, A; Bencivenni, G; Bologna, G; Bossi, F; Campana, P; Capon, G; Chiarella, V; Felici, G; Laurelli, P; Mannocchi, G; Murtas, F; Murtas, G P; Pepé-Altarelli, M; Dorris, S J; Halley, A W; ten Have, I; Knowles, I G; Lynch, J G; Morton, W T; O'Shea, V; Raine, C; Reeves, P; Scarr, J M; Smith, K; Smith, M G; Thompson, A S; Thomson, F; Thorn, S; Turnbull, R M; Becker, U; Braun, O; Geweniger, C; Graefe, G; Hanke, P; Hepp, V; Kluge, E E; Putzer, A; Rensch, B; Schmidt, M; Sommer, J; Stenzel, H; Tittel, K; Werner, S; Wunsch, M; Beuselinck, R; Binnie, David M; Cameron, W; Colling, D J; Dornan, Peter J; Konstantinidis, N P; Moneta, L; Moutoussi, A; Nash, J; San Martin, G; Sedgbeer, J K; Stacey, A M; Dissertori, G; Girtler, P; Kneringer, E; Kuhn, D; Rudolph, G; Bowdery, C K; Brodbeck, T J; Colrain, P; Crawford, G; Finch, A J; Foster, F; Hughes, G; Sloan, Terence; Whelan, E P; Williams, M I; Galla, A; Greene, A M; Kleinknecht, K; Quast, G; Raab, J; Renk, B; Sander, H G; Wanke, R; Van Gemmeren, P; Zeitnitz, C; Aubert, Jean-Jacques; Bencheikh, A M; Benchouk, C; Bonissent, A; Bujosa, G; Calvet, D; Carr, J; Diaconu, C A; Etienne, F; Thulasidas, M; Nicod, D; Payre, P; Rousseau, D; Talby, M; Abt, I; Assmann, R W; Bauer, C; Blum, Walter; Brown, D; Dietl, H; Dydak, Friedrich; Ganis, G; Gotzhein, C; Jakobs, K; Kroha, H; Lütjens, G; Lutz, Gerhard; Männer, W; Moser, H G; Richter, R H; Rosado-Schlosser, A; Schael, S; Settles, Ronald; Seywerd, H C J; Stierlin, U; Saint-Denis, R; Wolf, G; Alemany, R; Boucrot, J; Callot, O; Cordier, A; Courault, F; Davier, M; Duflot, L; Grivaz, J F; Heusse, P; Jacquet, M; Kim, D W; Le Diberder, F R; Lefrançois, J; Lutz, A M; Musolino, G; Nikolic, I A; Park, H J; Park, I C; Schune, M H; Simion, S; Veillet, J J; Videau, I; Abbaneo, D; Azzurri, P; Bagliesi, G; Batignani, G; Bettarini, S; Bozzi, C; Calderini, G; Carpinelli, M; Ciocci, M A; Ciulli, V; Dell'Orso, R; Fantechi, R; Ferrante, I; Foà, L; Forti, F; Giassi, A; Giorgi, M A; Gregorio, A; Ligabue, F; Lusiani, A; Marrocchesi, P S; Messineo, A; Rizzo, G; Sanguinetti, G; Sciabà, A; Spagnolo, P; Steinberger, Jack; Tenchini, Roberto; Tonelli, G; Triggiani, G; Vannini, C; Verdini, P G; Walsh, J; Betteridge, A P; Blair, G A; Bryant, L M; Cerutti, F; Gao, Y; Green, M G; Johnson, D L; Medcalf, T; Mir, L M; Perrodo, P; Strong, J A; Bertin, V; Botterill, David R; Clifft, R W; Edgecock, T R; Haywood, S; Edwards, M; Maley, P; Norton, P R; Thompson, J C; Bloch-Devaux, B; Colas, P; Duarte, H; Emery, S; Kozanecki, Witold; Lançon, E; Lemaire, M C; Locci, E; Marx, B; Pérez, P; Rander, J; Renardy, J F; Rosowsky, A; Roussarie, A; Schuller, J P; Schwindling, J; Si Mohand, D; Trabelsi, A; Vallage, B; Johnson, R P; Kim, H Y; Litke, A M; McNeil, M A; Taylor, G; Beddall, A; Booth, C N; Boswell, R; Cartwright, S L; Combley, F; Dawson, I; Köksal, A; Letho, M; Newton, W M; Rankin, C; Thompson, L F; Böhrer, A; Brandt, S; Cowan, G D; Feigl, E; Grupen, Claus; Lutters, G; Minguet-Rodríguez, J A; Rivera, F; Saraiva, P; Smolik, L; Stephan, F; Apollonio, M; Bosisio, L; Della Marina, R; Giannini, G; Gobbo, B; Ragusa, F; Rothberg, J E; Wasserbaech, S R; Armstrong, S R; Bellantoni, L; Elmer, P; Feng, P; Ferguson, D P S; Gao, Y S; González, S; Grahl, J; Harton, J L; Hayes, O J; Hu, H; McNamara, P A; Nachtman, J M; Orejudos, W; Pan, Y B; Saadi, Y; Schmitt, M; Scott, I J; Sharma, V; Turk, J; Walsh, A M; Wu Sau Lan; Wu, X; Yamartino, J M; Zheng, M; Zobernig, G
1996-01-01
An improved measurement of the average b hadron lifetime is performed using a sample of 1.5 million hadronic Z decays, collected during the 1991-1993 runs of ALEPH, with the silicon vertex detector fully operational. This uses the three-dimensional impact parameter distribution of lepton tracks coming from semileptonic b decays and yields an average b hadron lifetime of 1.533 \\pm 0.013 \\pm 0.022 ps.
Bivariate copulas on the exponentially weighted moving average control chart
Directory of Open Access Journals (Sweden)
Sasigarn Kuvattana
2016-10-01
Full Text Available This paper proposes four types of copulas on the Exponentially Weighted Moving Average (EWMA control chart when observations are from an exponential distribution using a Monte Carlo simulation approach. The performance of the control chart is based on the Average Run Length (ARL which is compared for each copula. Copula functions for specifying dependence between random variables are used and measured by Kendall’s tau. The results show that the Normal copula can be used for almost all shifts.
Averaging Bias Correction for Future IPDA Lidar Mission MERLIN
Directory of Open Access Journals (Sweden)
Tellier Yoann
2018-01-01
Full Text Available The CNES/DLR MERLIN satellite mission aims at measuring methane dry-air mixing ratio column (XCH4 and thus improving surface flux estimates. In order to get a 1% precision on XCH4 measurements, MERLIN signal processing assumes an averaging of data over 50 km. The induced biases due to the non-linear IPDA lidar equation are not compliant with accuracy requirements. This paper analyzes averaging biases issues and suggests correction algorithms tested on realistic simulated scenes.
Averaging Bias Correction for Future IPDA Lidar Mission MERLIN
Tellier, Yoann; Pierangelo, Clémence; Wirth, Martin; Gibert, Fabien
2018-04-01
The CNES/DLR MERLIN satellite mission aims at measuring methane dry-air mixing ratio column (XCH4) and thus improving surface flux estimates. In order to get a 1% precision on XCH4 measurements, MERLIN signal processing assumes an averaging of data over 50 km. The induced biases due to the non-linear IPDA lidar equation are not compliant with accuracy requirements. This paper analyzes averaging biases issues and suggests correction algorithms tested on realistic simulated scenes.
The average action for scalar fields near phase transitions
International Nuclear Information System (INIS)
Wetterich, C.
1991-08-01
We compute the average action for fields in two, three and four dimensions, including the effects of wave function renormalization. A study of the one loop evolution equations for the scale dependence of the average action gives a unified picture of the qualitatively different behaviour in various dimensions for discrete as well as abelian and nonabelian continuous symmetry. The different phases and the phase transitions can be infered from the evolution equation. (orig.)
Wave function collapse implies divergence of average displacement
Marchewka, A.; Schuss, Z.
2005-01-01
We show that propagating a truncated discontinuous wave function by Schr\\"odinger's equation, as asserted by the collapse axiom, gives rise to non-existence of the average displacement of the particle on the line. It also implies that there is no Zeno effect. On the other hand, if the truncation is done so that the reduced wave function is continuous, the average coordinate is finite and there is a Zeno effect. Therefore the collapse axiom of measurement needs to be revised.
Average geodesic distance of skeleton networks of Sierpinski tetrahedron
Yang, Jinjin; Wang, Songjing; Xi, Lifeng; Ye, Yongchao
2018-04-01
The average distance is concerned in the research of complex networks and is related to Wiener sum which is a topological invariant in chemical graph theory. In this paper, we study the skeleton networks of the Sierpinski tetrahedron, an important self-similar fractal, and obtain their asymptotic formula for average distances. To provide the formula, we develop some technique named finite patterns of integral of geodesic distance on self-similar measure for the Sierpinski tetrahedron.
International Nuclear Information System (INIS)
Norzita Yacob; Norhashidah Talip; Maznah Mahmud; Nurul Aizam Idayu Mat Sani; Nor Akma Samsuddin; Norafifah Ahmad Fabillah
2013-01-01
Determination of molecular weight by intrinsic viscosity measurement is a simple method for characterization of chitosan. To study the effect of radiation on molecular weight, chitosan was first irradiated using electron beam at different doses prior to measurement. Different concentrations of chitosan were prepared and measurement was done at room temperature. The flow time data was used to calculate the intrinsic viscosity by extrapolating the reduced viscosity to zero concentration. The value of intrinsic viscosity was then recalculated into the viscosity-average molecular weight using Mark-Houwink equation. (Author)
International Nuclear Information System (INIS)
Norzita Yacob; Norhashidah Talip; Maznah Mahmud
2011-01-01
Molecular weight of chitosan can be determined by different techniques such as Gel Permeation Chromatography (GPC), Static Light Scattering (SLS) and intrinsic viscosity measurement. Determination of molecular weight by intrinsic viscosity measurement is a simple method for characterization of chitosan. Different concentrations of chitosan were prepared and measurement was done at room temperature. The flow time data was used to calculate the intrinsic viscosity by extrapolating the reduced viscosity to zero concentration. The value of intrinsic viscosity was then recalculated into the viscosity-average molecular weight using Mark-Houwink equation. (author)
Radon and radon daughters indoors, problems in the determination of the annual average
International Nuclear Information System (INIS)
Swedjemark, G.A.
1984-01-01
The annual average of the concentration of radon and radon daughters in indoor air is required both in studies such as determining the collective dose to a population and at comparing with limits. Measurements are often carried out during a time period shorter than a year for practical reasons. Methods for estimating the uncertainties due to temporal variations in an annual average calculated from measurements carried out during various lengths of the sampling periods. These methods have been applied to the results from long-term measurements of radon-222 in a few houses. The possibilities to use correction factors in order to get a more adequate annual average have also been studied and some examples have been given. (orig.)
Average Soil Water Retention Curves Measured by Neutron Radiography
Energy Technology Data Exchange (ETDEWEB)
Cheng, Chu-Lin [ORNL; Perfect, Edmund [University of Tennessee, Knoxville (UTK); Kang, Misun [ORNL; Voisin, Sophie [ORNL; Bilheux, Hassina Z [ORNL; Horita, Juske [Texas Tech University (TTU); Hussey, Dan [NIST Center for Neutron Research (NCRN), Gaithersburg, MD
2011-01-01
Water retention curves are essential for understanding the hydrologic behavior of partially-saturated porous media and modeling flow transport processes within the vadose zone. In this paper we report direct measurements of the main drying and wetting branches of the average water retention function obtained using 2-dimensional neutron radiography. Flint sand columns were saturated with water and then drained under quasi-equilibrium conditions using a hanging water column setup. Digital images (2048 x 2048 pixels) of the transmitted flux of neutrons were acquired at each imposed matric potential (~10-15 matric potential values per experiment) at the NCNR BT-2 neutron imaging beam line. Volumetric water contents were calculated on a pixel by pixel basis using Beer-Lambert s law after taking into account beam hardening and geometric corrections. To remove scattering effects at high water contents the volumetric water contents were normalized (to give relative saturations) by dividing the drying and wetting sequences of images by the images obtained at saturation and satiation, respectively. The resulting pixel values were then averaged and combined with information on the imposed basal matric potentials to give average water retention curves. The average relative saturations obtained by neutron radiography showed an approximate one-to-one relationship with the average values measured volumetrically using the hanging water column setup. There were no significant differences (at p < 0.05) between the parameters of the van Genuchten equation fitted to the average neutron radiography data and those estimated from replicated hanging water column data. Our results indicate that neutron imaging is a very effective tool for quantifying the average water retention curve.
Atmospheric relative concentrations in building wakes
International Nuclear Information System (INIS)
Ramsdell, J.V. Jr.; Simonen, C.A.
1997-05-01
This report documents the ARCON96 computer code developed for the U.S. Nuclear Regulatory Commission Office of Nuclear Reactor Regulation for potential use in control room habitability assessments. It includes a user's guide to the code, a description of the technical basis for the code, and a programmer's guide to the code. The ARCON96 code uses hourly meteorological data and recently developed methods for estimating dispersion in the vicinity of buildings to calculate relative concentrations at control room air intakes that would be exceeded no more than five percent of the time. The concentrations are calculated for averaging periods ranging from one hour to 30 days in duration. ARCON96 is a revised version of ARCON95, which was developed for the NRC Office of Nuclear Regulatory Research. Changes in the code permit users to simulate releases from area sources as well as point sources. The method of averaging concentrations for periods longer than 2 hours has also been changed. The change in averaging procedures increases relative concentrations for these averaging periods. In general, the increase in concentrations is less than a factor of two. The increase is greatest for relatively short averaging periods, for example 0 to 8 hours and diminishes as the duration of the averaging period increases
Estimating average glandular dose by measuring glandular rate in mammograms
International Nuclear Information System (INIS)
Goto, Sachiko; Azuma, Yoshiharu; Sumimoto, Tetsuhiro; Eiho, Shigeru
2003-01-01
The glandular rate of the breast was objectively measured in order to calculate individual patient exposure dose (average glandular dose) in mammography. By employing image processing techniques and breast-equivalent phantoms with various glandular rate values, a conversion curve for pixel value to glandular rate can be determined by a neural network. Accordingly, the pixel values in clinical mammograms can be converted to the glandular rate value for each pixel. The individual average glandular dose can therefore be calculated using the individual glandular rates on the basis of the dosimetry method employed for quality control in mammography. In the present study, a data set of 100 craniocaudal mammograms from 50 patients was used to evaluate our method. The average glandular rate and average glandular dose of the data set were 41.2% and 1.79 mGy, respectively. The error in calculating the individual glandular rate can be estimated to be less than ±3%. When the calculation error of the glandular rate is taken into consideration, the error in the individual average glandular dose can be estimated to be 13% or less. We feel that our method for determining the glandular rate from mammograms is useful for minimizing subjectivity in the evaluation of patient breast composition. (author)
Accurate phenotyping: Reconciling approaches through Bayesian model averaging.
Directory of Open Access Journals (Sweden)
Carla Chia-Ming Chen
Full Text Available Genetic research into complex diseases is frequently hindered by a lack of clear biomarkers for phenotype ascertainment. Phenotypes for such diseases are often identified on the basis of clinically defined criteria; however such criteria may not be suitable for understanding the genetic composition of the diseases. Various statistical approaches have been proposed for phenotype definition; however our previous studies have shown that differences in phenotypes estimated using different approaches have substantial impact on subsequent analyses. Instead of obtaining results based upon a single model, we propose a new method, using Bayesian model averaging to overcome problems associated with phenotype definition. Although Bayesian model averaging has been used in other fields of research, this is the first study that uses Bayesian model averaging to reconcile phenotypes obtained using multiple models. We illustrate the new method by applying it to simulated genetic and phenotypic data for Kofendred personality disorder-an imaginary disease with several sub-types. Two separate statistical methods were used to identify clusters of individuals with distinct phenotypes: latent class analysis and grade of membership. Bayesian model averaging was then used to combine the two clusterings for the purpose of subsequent linkage analyses. We found that causative genetic loci for the disease produced higher LOD scores using model averaging than under either individual model separately. We attribute this improvement to consolidation of the cores of phenotype clusters identified using each individual method.
Yearly, seasonal and monthly daily average diffuse sky radiation models
International Nuclear Information System (INIS)
Kassem, A.S.; Mujahid, A.M.; Turner, D.W.
1993-01-01
A daily average diffuse sky radiation regression model based on daily global radiation was developed utilizing two year data taken near Blytheville, Arkansas (Lat. =35.9 0 N, Long. = 89.9 0 W), U.S.A. The model has a determination coefficient of 0.91 and 0.092 standard error of estimate. The data were also analyzed for a seasonal dependence and four seasonal average daily models were developed for the spring, summer, fall and winter seasons. The coefficient of determination is 0.93, 0.81, 0.94 and 0.93, whereas the standard error of estimate is 0.08, 0.102, 0.042 and 0.075 for spring, summer, fall and winter, respectively. A monthly average daily diffuse sky radiation model was also developed. The coefficient of determination is 0.92 and the standard error of estimate is 0.083. A seasonal monthly average model was also developed which has 0.91 coefficient of determination and 0.085 standard error of estimate. The developed monthly daily average and daily models compare well with a selected number of previously developed models. (author). 11 ref., figs., tabs
Average cross sections for the 252Cf neutron spectrum
International Nuclear Information System (INIS)
Dezso, Z.; Csikai, J.
1977-01-01
A number of average cross sections have been measured for 252 Cf neutrons in (n, γ), (n,p), (n,2n), (n,α) reactions by the activation method and for fission by fission chamber. Cross sections have been determined for 19 elements and 45 reactions. The (n,γ) cross section values lie in the interval from 0.3 to 200 mb. The data as a function of target neutron number increases up to about N=60 with minimum near to dosed shells. The values lie between 0.3 mb and 113 mb. These cross sections decrease significantly with increasing the threshold energy. The values are below 20 mb. The data do not exceed 10 mb. Average (n,p) cross sections as a function of the threshold energy and average fission cross sections as a function of Zsup(4/3)/A are shown. The results obtained are summarized in tables
Testing averaged cosmology with type Ia supernovae and BAO data
Energy Technology Data Exchange (ETDEWEB)
Santos, B.; Alcaniz, J.S. [Departamento de Astronomia, Observatório Nacional, 20921-400, Rio de Janeiro – RJ (Brazil); Coley, A.A. [Department of Mathematics and Statistics, Dalhousie University, Halifax, B3H 3J5 Canada (Canada); Devi, N. Chandrachani, E-mail: thoven@on.br, E-mail: aac@mathstat.dal.ca, E-mail: chandrachaniningombam@astro.unam.mx, E-mail: alcaniz@on.br [Instituto de Astronomía, Universidad Nacional Autónoma de México, Box 70-264, México City, México (Mexico)
2017-02-01
An important problem in precision cosmology is the determination of the effects of averaging and backreaction on observational predictions, particularly in view of the wealth of new observational data and improved statistical techniques. In this paper, we discuss the observational viability of a class of averaged cosmologies which consist of a simple parametrized phenomenological two-scale backreaction model with decoupled spatial curvature parameters. We perform a Bayesian model selection analysis and find that this class of averaged phenomenological cosmological models is favored with respect to the standard ΛCDM cosmological scenario when a joint analysis of current SNe Ia and BAO data is performed. In particular, the analysis provides observational evidence for non-trivial spatial curvature.
Average contraction and synchronization of complex switched networks
International Nuclear Information System (INIS)
Wang Lei; Wang Qingguo
2012-01-01
This paper introduces an average contraction analysis for nonlinear switched systems and applies it to investigating the synchronization of complex networks of coupled systems with switching topology. For a general nonlinear system with a time-dependent switching law, a basic convergence result is presented according to average contraction analysis, and a special case where trajectories of a distributed switched system converge to a linear subspace is then investigated. Synchronization is viewed as the special case with all trajectories approaching the synchronization manifold, and is thus studied for complex networks of coupled oscillators with switching topology. It is shown that the synchronization of a complex switched network can be evaluated by the dynamics of an isolated node, the coupling strength and the time average of the smallest eigenvalue associated with the Laplacians of switching topology and the coupling fashion. Finally, numerical simulations illustrate the effectiveness of the proposed methods. (paper)
The Health Effects of Income Inequality: Averages and Disparities.
Truesdale, Beth C; Jencks, Christopher
2016-01-01
Much research has investigated the association of income inequality with average life expectancy, usually finding negative correlations that are not very robust. A smaller body of work has investigated socioeconomic disparities in life expectancy, which have widened in many countries since 1980. These two lines of work should be seen as complementary because changes in average life expectancy are unlikely to affect all socioeconomic groups equally. Although most theories imply long and variable lags between changes in income inequality and changes in health, empirical evidence is confined largely to short-term effects. Rising income inequality can affect individuals in two ways. Direct effects change individuals' own income. Indirect effects change other people's income, which can then change a society's politics, customs, and ideals, altering the behavior even of those whose own income remains unchanged. Indirect effects can thus change both average health and the slope of the relationship between individual income and health.
Testing averaged cosmology with type Ia supernovae and BAO data
International Nuclear Information System (INIS)
Santos, B.; Alcaniz, J.S.; Coley, A.A.; Devi, N. Chandrachani
2017-01-01
An important problem in precision cosmology is the determination of the effects of averaging and backreaction on observational predictions, particularly in view of the wealth of new observational data and improved statistical techniques. In this paper, we discuss the observational viability of a class of averaged cosmologies which consist of a simple parametrized phenomenological two-scale backreaction model with decoupled spatial curvature parameters. We perform a Bayesian model selection analysis and find that this class of averaged phenomenological cosmological models is favored with respect to the standard ΛCDM cosmological scenario when a joint analysis of current SNe Ia and BAO data is performed. In particular, the analysis provides observational evidence for non-trivial spatial curvature.
Perceived Average Orientation Reflects Effective Gist of the Surface.
Cha, Oakyoon; Chong, Sang Chul
2018-03-01
The human ability to represent ensemble visual information, such as average orientation and size, has been suggested as the foundation of gist perception. To effectively summarize different groups of objects into the gist of a scene, observers should form ensembles separately for different groups, even when objects have similar visual features across groups. We hypothesized that the visual system utilizes perceptual groups characterized by spatial configuration and represents separate ensembles for different groups. Therefore, participants could not integrate ensembles of different perceptual groups on a task basis. We asked participants to determine the average orientation of visual elements comprising a surface with a contour situated inside. Although participants were asked to estimate the average orientation of all the elements, they ignored orientation signals embedded in the contour. This constraint may help the visual system to keep the visual features of occluding objects separate from those of the occluded objects.
Object detection by correlation coefficients using azimuthally averaged reference projections.
Nicholson, William V
2004-11-01
A method of computing correlation coefficients for object detection that takes advantage of using azimuthally averaged reference projections is described and compared with two alternative methods-computing a cross-correlation function or a local correlation coefficient versus the azimuthally averaged reference projections. Two examples of an application from structural biology involving the detection of projection views of biological macromolecules in electron micrographs are discussed. It is found that a novel approach to computing a local correlation coefficient versus azimuthally averaged reference projections, using a rotational correlation coefficient, outperforms using a cross-correlation function and a local correlation coefficient in object detection from simulated images with a range of levels of simulated additive noise. The three approaches perform similarly in detecting macromolecular views in electron microscope images of a globular macrolecular complex (the ribosome). The rotational correlation coefficient outperforms the other methods in detection of keyhole limpet hemocyanin macromolecular views in electron micrographs.
A Martian PFS average spectrum: Comparison with ISO SWS
Formisano, V.; Encrenaz, T.; Fonti, S.; Giuranna, M.; Grassi, D.; Hirsh, H.; Khatuntsev, I.; Ignatiev, N.; Lellouch, E.; Maturilli, A.; Moroz, V.; Orleanski, P.; Piccioni, G.; Rataj, M.; Saggin, B.; Zasova, L.
2005-08-01
The evaluation of the planetary Fourier spectrometer performance at Mars is presented by comparing an average spectrum with the ISO spectrum published by Lellouch et al. [2000. Planet. Space Sci. 48, 1393.]. First, the average conditions of Mars atmosphere are compared, then the mixing ratios of the major gases are evaluated. Major and minor bands of CO 2 are compared, from the point of view of features characteristics and bands depth. The spectral resolution is also compared using several solar lines. The result indicates that PFS radiance is valid to better than 1% in the wavenumber range 1800-4200 cm -1 for the average spectrum considered (1680 measurements). The PFS monochromatic transfer function generates an overshooting on the left-hand side of strong narrow lines (solar or atmospheric). The spectral resolution of PFS is of the order of 1.3 cm -1 or better. A large number of narrow features to be identified are discovered.
Size and emotion averaging: costs of dividing attention after all.
Brand, John; Oriet, Chris; Tottenham, Laurie Sykes
2012-03-01
Perceptual averaging is a process by which sets of similar items are represented by summary statistics such as their average size, luminance, or orientation. Researchers have argued that this process is automatic, able to be carried out without interference from concurrent processing. Here, we challenge this conclusion and demonstrate a reliable cost of computing the mean size of circles distinguished by colour (Experiments 1 and 2) and the mean emotionality of faces distinguished by sex (Experiment 3). We also test the viability of two strategies that could have allowed observers to guess the correct response without computing the average size or emotionality of both sets concurrently. We conclude that although two means can be computed concurrently, doing so incurs a cost of dividing attention.
A virtual pebble game to ensemble average graph rigidity.
González, Luis C; Wang, Hui; Livesay, Dennis R; Jacobs, Donald J
2015-01-01
The body-bar Pebble Game (PG) algorithm is commonly used to calculate network rigidity properties in proteins and polymeric materials. To account for fluctuating interactions such as hydrogen bonds, an ensemble of constraint topologies are sampled, and average network properties are obtained by averaging PG characterizations. At a simpler level of sophistication, Maxwell constraint counting (MCC) provides a rigorous lower bound for the number of internal degrees of freedom (DOF) within a body-bar network, and it is commonly employed to test if a molecular structure is globally under-constrained or over-constrained. MCC is a mean field approximation (MFA) that ignores spatial fluctuations of distance constraints by replacing the actual molecular structure by an effective medium that has distance constraints globally distributed with perfect uniform density. The Virtual Pebble Game (VPG) algorithm is a MFA that retains spatial inhomogeneity in the density of constraints on all length scales. Network fluctuations due to distance constraints that may be present or absent based on binary random dynamic variables are suppressed by replacing all possible constraint topology realizations with the probabilities that distance constraints are present. The VPG algorithm is isomorphic to the PG algorithm, where integers for counting "pebbles" placed on vertices or edges in the PG map to real numbers representing the probability to find a pebble. In the VPG, edges are assigned pebble capacities, and pebble movements become a continuous flow of probability within the network. Comparisons between the VPG and average PG results over a test set of proteins and disordered lattices demonstrate the VPG quantitatively estimates the ensemble average PG results well. The VPG performs about 20% faster than one PG, and it provides a pragmatic alternative to averaging PG rigidity characteristics over an ensemble of constraint topologies. The utility of the VPG falls in between the most
Exactly averaged equations for flow and transport in random media
International Nuclear Information System (INIS)
Shvidler, Mark; Karasaki, Kenzi
2001-01-01
It is well known that exact averaging of the equations of flow and transport in random porous media can be realized only for a small number of special, occasionally exotic, fields. On the other hand, the properties of approximate averaging methods are not yet fully understood. For example, the convergence behavior and the accuracy of truncated perturbation series. Furthermore, the calculation of the high-order perturbations is very complicated. These problems for a long time have stimulated attempts to find the answer for the question: Are there in existence some exact general and sufficiently universal forms of averaged equations? If the answer is positive, there arises the problem of the construction of these equations and analyzing them. There exist many publications related to these problems and oriented on different applications: hydrodynamics, flow and transport in porous media, theory of elasticity, acoustic and electromagnetic waves in random fields, etc. We present a method of finding the general form of exactly averaged equations for flow and transport in random fields by using (1) an assumption of the existence of Green's functions for appropriate stochastic problems, (2) some general properties of the Green's functions, and (3) the some basic information about the random fields of the conductivity, porosity and flow velocity. We present a general form of the exactly averaged non-local equations for the following cases. 1. Steady-state flow with sources in porous media with random conductivity. 2. Transient flow with sources in compressible media with random conductivity and porosity. 3. Non-reactive solute transport in random porous media. We discuss the problem of uniqueness and the properties of the non-local averaged equations, for the cases with some types of symmetry (isotropic, transversal isotropic, orthotropic) and we analyze the hypothesis of the structure non-local equations in general case of stochastically homogeneous fields. (author)
Increase in average foveal thickness after internal limiting membrane peeling
Directory of Open Access Journals (Sweden)
Kumagai K
2017-04-01
Full Text Available Kazuyuki Kumagai,1 Mariko Furukawa,1 Tetsuyuki Suetsugu,1 Nobuchika Ogino2 1Department of Ophthalmology, Kami-iida Daiichi General Hospital, 2Department of Ophthalmology, Nishigaki Eye Clinic, Aichi, Japan Purpose: To report the findings in three cases in which the average foveal thickness was increased after a thin epiretinal membrane (ERM was removed by vitrectomy with internal limiting membrane (ILM peeling.Methods: The foveal contour was normal preoperatively in all eyes. All cases underwent successful phacovitrectomy with ILM peeling for a thin ERM. The optical coherence tomography (OCT images were examined before and after the surgery. The changes in the average foveal (1 mm thickness and the foveal areas within 500 µm from the foveal center were measured. The postoperative changes in the inner and outer retinal areas determined from the cross-sectional OCT images were analyzed.Results: The average foveal thickness and the inner and outer foveal areas increased significantly after the surgery in each of the three cases. The percentage increase in the average foveal thickness relative to the baseline thickness was 26% in Case 1, 29% in Case 2, and 31% in Case 3. The percentage increase in the foveal inner retinal area was 71% in Case 1, 113% in Case 2, and 110% in Case 3, and the percentage increase in foveal outer retinal area was 8% in Case 1, 13% in Case 2, and 18% in Case 3.Conclusion: The increase in the average foveal thickness and the inner and outer foveal areas suggests that a centripetal movement of the inner and outer retinal layers toward the foveal center probably occurred due to the ILM peeling. Keywords: internal limiting membrane, optical coherence tomography, average foveal thickness, epiretinal membrane, vitrectomy
Positivity of the spherically averaged atomic one-electron density
DEFF Research Database (Denmark)
Fournais, Søren; Hoffmann-Ostenhof, Maria; Hoffmann-Ostenhof, Thomas
2008-01-01
We investigate the positivity of the spherically averaged atomic one-electron density . For a which stems from a physical ground state we prove that for r ≥ 0. This article may be reproduced in its entirety for non-commercial purposes.......We investigate the positivity of the spherically averaged atomic one-electron density . For a which stems from a physical ground state we prove that for r ≥ 0. This article may be reproduced in its entirety for non-commercial purposes....
Research & development and growth: A Bayesian model averaging analysis
Czech Academy of Sciences Publication Activity Database
Horváth, Roman
2011-01-01
Roč. 28, č. 6 (2011), s. 2669-2673 ISSN 0264-9993. [Society for Non-linear Dynamics and Econometrics Annual Conferencen. Washington DC, 16.03.2011-18.03.2011] R&D Projects: GA ČR GA402/09/0965 Institutional research plan: CEZ:AV0Z10750506 Keywords : Research and development * Growth * Bayesian model averaging Subject RIV: AH - Economic s Impact factor: 0.701, year: 2011 http://library.utia.cas.cz/separaty/2011/E/horvath-research & development and growth a bayesian model averaging analysis.pdf
MAIN STAGES SCIENTIFIC AND PRODUCTION MASTERING THE TERRITORY AVERAGE URAL
Directory of Open Access Journals (Sweden)
V.S. Bochko
2006-09-01
Full Text Available Questions of the shaping Average Ural, as industrial territory, on base her scientific study and production mastering are considered in the article. It is shown that studies of Ural resources and particularities of the vital activity of its population were concerned by Russian and foreign scientist in XVIII-XIX centuries. It is noted that in XX century there was a transition to systematic organizing-economic study of production power, society and natures of Average Ural. More attention addressed on new problems of region and on needs of their scientific solving.
High-Average, High-Peak Current Injector Design
Biedron, S G; Virgo, M
2005-01-01
There is increasing interest in high-average-power (>100 kW), um-range FELs. These machines require high peak current (~1 kA), modest transverse emittance, and beam energies of ~100 MeV. High average currents (~1 A) place additional constraints on the design of the injector. We present a design for an injector intended to produce the required peak currents at the injector, eliminating the need for magnetic compression within the linac. This reduces the potential for beam quality degradation due to CSR and space charge effects within magnetic chicanes.
Non-self-averaging nucleation rate due to quenched disorder
International Nuclear Information System (INIS)
Sear, Richard P
2012-01-01
We study the nucleation of a new thermodynamic phase in the presence of quenched disorder. The quenched disorder is a generic model of both impurities and disordered porous media; both are known to have large effects on nucleation. We find that the nucleation rate is non-self-averaging. This is in a simple Ising model with clusters of quenched spins. We also show that non-self-averaging behaviour is straightforward to detect in experiments, and may be rather common. (fast track communication)
A note on moving average models for Gaussian random fields
DEFF Research Database (Denmark)
Hansen, Linda Vadgård; Thorarinsdottir, Thordis L.
The class of moving average models offers a flexible modeling framework for Gaussian random fields with many well known models such as the Matérn covariance family and the Gaussian covariance falling under this framework. Moving average models may also be viewed as a kernel smoothing of a Lévy...... basis, a general modeling framework which includes several types of non-Gaussian models. We propose a new one-parameter spatial correlation model which arises from a power kernel and show that the associated Hausdorff dimension of the sample paths can take any value between 2 and 3. As a result...
International Nuclear Information System (INIS)
Nelson, R.A.
1987-01-01
More than 250 replicate measurements of outdoor Rn concentration integrated over quarterly periods were made to estimate the random component of the measurement uncertainty of Track Etch detectors (type F) under outdoor conditions. The measurements were performed around three U mill tailings piles to provide a range of environmental concentrations. The measurement uncertainty was typically greater than could be accounted for by Poisson counting statistics. Average coefficients of variation of the order of 20% for all measured concentrations were found. It is concluded that alpha track detectors can be successfully used to determine annual average outdoor Rn concentrations through the use of careful quality control procedures. These include rapid deployment and collection of detectors to minimize unintended Rn exposure, careful packaging and shipping to and from the manufacturer, use of direct sunlight shields for all detectors and careful and secure mounting of all detectors in as similar a manner as possible. The use of multiple (at least duplicate) detectors at each monitoring location and an exposure period of no less than one quarter are suggested
Small Bandwidth Asymptotics for Density-Weighted Average Derivatives
DEFF Research Database (Denmark)
Cattaneo, Matias D.; Crump, Richard K.; Jansson, Michael
This paper proposes (apparently) novel standard error formulas for the density-weighted average derivative estimator of Powell, Stock, and Stoker (1989). Asymptotic validity of the standard errors developed in this paper does not require the use of higher-order kernels and the standard errors...
High Average Power UV Free Electron Laser Experiments At JLAB
International Nuclear Information System (INIS)
Douglas, David; Benson, Stephen; Evtushenko, Pavel; Gubeli, Joseph; Hernandez-Garcia, Carlos; Legg, Robert; Neil, George; Powers, Thomas; Shinn, Michelle; Tennant, Christopher; Williams, Gwyn
2012-01-01
Having produced 14 kW of average power at ∼2 microns, JLAB has shifted its focus to the ultraviolet portion of the spectrum. This presentation will describe the JLab UV Demo FEL, present specifics of its driver ERL, and discuss the latest experimental results from FEL experiments and machine operations.
Establishment of Average Body Measurement and the Development ...
African Journals Online (AJOL)
cce
body measurement for height and backneck to waist for ages 2,3,4 and 5 years. The ... average measurements of the different parts of the body must be established. ..... and OAU Charter on Rights of the child: Lagos: Nigeria Country office.
Adaptive Spontaneous Transitions between Two Mechanisms of Numerical Averaging.
Brezis, Noam; Bronfman, Zohar Z; Usher, Marius
2015-06-04
We investigated the mechanism with which humans estimate numerical averages. Participants were presented with 4, 8 or 16 (two-digit) numbers, serially and rapidly (2 numerals/second) and were instructed to convey the sequence average. As predicted by a dual, but not a single-component account, we found a non-monotonic influence of set-size on accuracy. Moreover, we observed a marked decrease in RT as set-size increases and RT-accuracy tradeoff in the 4-, but not in the 16-number condition. These results indicate that in accordance with the normative directive, participants spontaneously employ analytic/sequential thinking in the 4-number condition and intuitive/holistic thinking in the 16-number condition. When the presentation rate is extreme (10 items/sec) we find that, while performance still remains high, the estimations are now based on intuitive processing. The results are accounted for by a computational model postulating population-coding underlying intuitive-averaging and working-memory-mediated symbolic procedures underlying analytical-averaging, with flexible allocation between the two.
Determination of the average lifetime of bottom hadrons
Energy Technology Data Exchange (ETDEWEB)
Althoff, M; Braunschweig, W; Kirschfink, F J; Martyn, H U; Rosskamp, P; Schmitz, D; Siebke, H; Wallraff, W [Technische Hochschule Aachen (Germany, F.R.). Lehrstuhl fuer Experimentalphysik 1A und 1. Physikalisches Inst.; Eisenmann, J; Fischer, H M
1984-12-27
We have determined the average lifetime of hadrons containing b quarks produced in e/sup +/e/sup -/ annihilation to be tausub(B)=1.83 x 10/sup -12/ s. Our method uses charged decay products from both non-leptonic and semileptonic decay modes.
Determination of the average lifetime of bottom hadrons
Energy Technology Data Exchange (ETDEWEB)
Althoff, M; Braunschweig, W; Kirschfink, F J; Martyn, H U; Rosskamp, P; Schmitz, D; Siebke, H; Wallraff, W; Eisenmann, J; Fischer, H M
1984-12-27
We have determined the average lifetime of hadrons containing b quarks produced in e e annihilation to be tausub(B)=1.83x10 S s. Our method uses charged decay products from both non-leptonic and semileptonic decay modes. (orig./HSI).
Time Series ARIMA Models of Undergraduate Grade Point Average.
Rogers, Bruce G.
The Auto-Regressive Integrated Moving Average (ARIMA) Models, often referred to as Box-Jenkins models, are regression methods for analyzing sequential dependent observations with large amounts of data. The Box-Jenkins approach, a three-stage procedure consisting of identification, estimation and diagnosis, was used to select the most appropriate…
Crystallographic extraction and averaging of data from small image areas
Perkins, GA; Downing, KH; Glaeser, RM
The accuracy of structure factor phases determined from electron microscope images is determined mainly by the level of statistical significance, which is limited by the low level of allowed electron exposure and by the number of identical unit cells that can be averaged. It is shown here that
Reducing Noise by Repetition: Introduction to Signal Averaging
Hassan, Umer; Anwar, Muhammad Sabieh
2010-01-01
This paper describes theory and experiments, taken from biophysics and physiological measurements, to illustrate the technique of signal averaging. In the process, students are introduced to the basic concepts of signal processing, such as digital filtering, Fourier transformation, baseline correction, pink and Gaussian noise, and the cross- and…
Environmental stresses can alleviate the average deleterious effect of mutations
Directory of Open Access Journals (Sweden)
Leibler Stanislas
2003-05-01
Full Text Available Abstract Background Fundamental questions in evolutionary genetics, including the possible advantage of sexual reproduction, depend critically on the effects of deleterious mutations on fitness. Limited existing experimental evidence suggests that, on average, such effects tend to be aggravated under environmental stresses, consistent with the perception that stress diminishes the organism's ability to tolerate deleterious mutations. Here, we ask whether there are also stresses with the opposite influence, under which the organism becomes more tolerant to mutations. Results We developed a technique, based on bioluminescence, which allows accurate automated measurements of bacterial growth rates at very low cell densities. Using this system, we measured growth rates of Escherichia coli mutants under a diverse set of environmental stresses. In contrast to the perception that stress always reduces the organism's ability to tolerate mutations, our measurements identified stresses that do the opposite – that is, despite decreasing wild-type growth, they alleviate, on average, the effect of deleterious mutations. Conclusions Our results show a qualitative difference between various environmental stresses ranging from alleviation to aggravation of the average effect of mutations. We further show how the existence of stresses that are biased towards alleviation of the effects of mutations may imply the existence of average epistatic interactions between mutations. The results thus offer a connection between the two main factors controlling the effects of deleterious mutations: environmental conditions and epistatic interactions.
The background effective average action approach to quantum gravity
DEFF Research Database (Denmark)
D’Odorico, G.; Codello, A.; Pagani, C.
2016-01-01
of an UV attractive non-Gaussian fixed-point, which we find characterized by real critical exponents. Our closure method is general and can be applied systematically to more general truncations of the gravitational effective average action. © Springer International Publishing Switzerland 2016....
Error estimates in horocycle averages asymptotics: challenges from string theory
Cardella, M.A.
2010-01-01
For modular functions of rapid decay, a classical result connects the error estimate in their long horocycle average asymptotic to the Riemann hypothesis. We study similar asymptotics, for modular functions with not that mild growing conditions, such as of polynomial growth and of exponential growth
Moving average rules as a source of market instability
Chiarella, C.; He, X.Z.; Hommes, C.H.
2006-01-01
Despite the pervasiveness of the efficient markets paradigm in the academic finance literature, the use of various moving average (MA) trading rules remains popular with financial market practitioners. This paper proposes a stochastic dynamic financial market model in which demand for traded assets
arXiv Averaged Energy Conditions and Bouncing Universes
Giovannini, Massimo
2017-11-16
The dynamics of bouncing universes is characterized by violating certain coordinate-invariant restrictions on the total energy-momentum tensor, customarily referred to as energy conditions. Although there could be epochs in which the null energy condition is locally violated, it may perhaps be enforced in an averaged sense. Explicit examples of this possibility are investigated in different frameworks.
26 CFR 1.1301-1 - Averaging of farm income.
2010-04-01
... January 1, 2003, rental income based on a share of a tenant's production determined under an unwritten... the Collection of Income Tax at Source on Wages (Federal income tax withholding), or the amount of net... 26 Internal Revenue 11 2010-04-01 2010-04-01 true Averaging of farm income. 1.1301-1 Section 1...
Implications of Methodist clergies' average lifespan and missional ...
African Journals Online (AJOL)
2015-06-09
Jun 9, 2015 ... The author of Genesis 5 paid meticulous attention to the lifespan of several people ... of Southern Africa (MCSA), and to argue that memories of the ... average ages at death were added up and the sum was divided by 12 (which represents the 12 ..... not explicit in how the departed Methodist ministers were.
Pareto Principle in Datamining: an Above-Average Fencing Algorithm
Directory of Open Access Journals (Sweden)
K. Macek
2008-01-01
Full Text Available This paper formulates a new datamining problem: which subset of input space has the relatively highest output where the minimal size of this subset is given. This can be useful where usual datamining methods fail because of error distribution asymmetry. The paper provides a novel algorithm for this datamining problem, and compares it with clustering of above-average individuals.
Average Distance Travelled To School by Primary and Secondary ...
African Journals Online (AJOL)
This study investigated average distance travelled to school by students in primary and secondary schools in Anambra, Enugu, and Ebonyi States and effect on attendance. These are among the top ten densely populated and educationally advantaged States in Nigeria. Research evidences report high dropout rates in ...
Trend of Average Wages as Indicator of Hypothetical Money Illusion
Directory of Open Access Journals (Sweden)
Julian Daszkowski
2010-06-01
Full Text Available The definition of wage in Poland not before 1998 includes any value of social security contribution. Changed definition creates higher level of reported wages, but was expected not to influence the take home pay. Nevertheless, the trend of average wages, after a short period, has returned to its previous line. Such effect is explained in the term of money illusion.
Computation of the average energy for LXY electrons
International Nuclear Information System (INIS)
Grau Carles, A.; Grau, A.
1996-01-01
The application of an atomic rearrangement model in which we only consider the three shells K, L and M, to compute the counting efficiency for electron capture nuclides, requires a fine averaged energy value for LMN electrons. In this report, we illustrate the procedure with two example, ''125 I and ''109 Cd. (Author) 4 refs
Bounding quantum gate error rate based on reported average fidelity
International Nuclear Information System (INIS)
Sanders, Yuval R; Wallman, Joel J; Sanders, Barry C
2016-01-01
Remarkable experimental advances in quantum computing are exemplified by recent announcements of impressive average gate fidelities exceeding 99.9% for single-qubit gates and 99% for two-qubit gates. Although these high numbers engender optimism that fault-tolerant quantum computing is within reach, the connection of average gate fidelity with fault-tolerance requirements is not direct. Here we use reported average gate fidelity to determine an upper bound on the quantum-gate error rate, which is the appropriate metric for assessing progress towards fault-tolerant quantum computation, and we demonstrate that this bound is asymptotically tight for general noise. Although this bound is unlikely to be saturated by experimental noise, we demonstrate using explicit examples that the bound indicates a realistic deviation between the true error rate and the reported average fidelity. We introduce the Pauli distance as a measure of this deviation, and we show that knowledge of the Pauli distance enables tighter estimates of the error rate of quantum gates. (fast track communication)
75 FR 78157 - Farmer and Fisherman Income Averaging
2010-12-15
... to the averaging of farm and fishing income in computing income tax liability. The regulations...: PART 1--INCOME TAXES 0 Paragraph 1. The authority citation for part 1 continues to read in part as... section 1 tax would be increased if one-third of elected farm income were allocated to each year. The...
Domain-averaged Fermi-hole Analysis for Solids
Czech Academy of Sciences Publication Activity Database
Baranov, A.; Ponec, Robert; Kohout, M.
2012-01-01
Roč. 137, č. 21 (2012), s. 214109 ISSN 0021-9606 R&D Projects: GA ČR GA203/09/0118 Institutional support: RVO:67985858 Keywords : bonding in solids * domain averaged fermi hole * natural orbitals Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.164, year: 2012
Characteristics of phase-averaged equations for modulated wave groups
Klopman, G.; Petit, H.A.H.; Battjes, J.A.
2000-01-01
The project concerns the influence of long waves on coastal morphology. The modelling of the combined motion of the long waves and short waves in the horizontal plane is done by phase-averaging over the short wave motion and using intra-wave modelling for the long waves, see e.g. Roelvink (1993).
A depth semi-averaged model for coastal dynamics
Antuono, M.; Colicchio, G.; Lugni, C.; Greco, M.; Brocchini, M.
2017-05-01
The present work extends the semi-integrated method proposed by Antuono and Brocchini ["Beyond Boussinesq-type equations: Semi-integrated models for coastal dynamics," Phys. Fluids 25(1), 016603 (2013)], which comprises a subset of depth-averaged equations (similar to Boussinesq-like models) and a Poisson equation that accounts for vertical dynamics. Here, the subset of depth-averaged equations has been reshaped in a conservative-like form and both the Poisson equation formulations proposed by Antuono and Brocchini ["Beyond Boussinesq-type equations: Semi-integrated models for coastal dynamics," Phys. Fluids 25(1), 016603 (2013)] are investigated: the former uses the vertical velocity component (formulation A) and the latter a specific depth semi-averaged variable, ϒ (formulation B). Our analyses reveal that formulation A is prone to instabilities as wave nonlinearity increases. On the contrary, formulation B allows an accurate, robust numerical implementation. Test cases derived from the scientific literature on Boussinesq-type models—i.e., solitary and Stokes wave analytical solutions for linear dispersion and nonlinear evolution and experimental data for shoaling properties—are used to assess the proposed solution strategy. It is found that the present method gives reliable predictions of wave propagation in shallow to intermediate waters, in terms of both semi-averaged variables and conservation properties.
Effect of tank geometry on its average performance
Orlov, Aleksey A.; Tsimbalyuk, Alexandr F.; Malyugin, Roman V.; Leontieva, Daria A.; Kotelnikova, Alexandra A.
2018-03-01
The mathematical model of non-stationary filling of vertical submerged tanks with gaseous uranium hexafluoride is presented in the paper. There are calculations of the average productivity, heat exchange area, and filling time of various volumes tanks with smooth inner walls depending on their "height : radius" ratio as well as the average productivity, degree, and filling time of horizontal ribbing tank with volume 6.10-2 m3 with change central hole diameter of the ribs. It has been shown that the growth of "height / radius" ratio in tanks with smooth inner walls up to the limiting values allows significantly increasing tank average productivity and reducing its filling time. Growth of H/R ratio of tank with volume 1.0 m3 to the limiting values (in comparison with the standard tank having H/R equal 3.49) augments tank productivity by 23.5 % and the heat exchange area by 20%. Besides, we have demonstrated that maximum average productivity and a minimum filling time are reached for the tank with volume 6.10-2 m3 having central hole diameter of horizontal ribs 6.4.10-2 m.
An averaged polarizable potential for multiscale modeling in phospholipid membranes
DEFF Research Database (Denmark)
Witzke, Sarah; List, Nanna Holmgaard; Olsen, Jógvan Magnus Haugaard
2017-01-01
A set of average atom-centered charges and polarizabilities has been developed for three types of phospholipids for use in polarizable embedding calculations. The lipids investigated are 1,2-dimyristoyl-sn-glycero-3-phosphocholine, 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine, and 1-palmitoyl...
Post-model selection inference and model averaging
Directory of Open Access Journals (Sweden)
Georges Nguefack-Tsague
2011-07-01
Full Text Available Although model selection is routinely used in practice nowadays, little is known about its precise effects on any subsequent inference that is carried out. The same goes for the effects induced by the closely related technique of model averaging. This paper is concerned with the use of the same data first to select a model and then to carry out inference, in particular point estimation and point prediction. The properties of the resulting estimator, called a post-model-selection estimator (PMSE, are hard to derive. Using selection criteria such as hypothesis testing, AIC, BIC, HQ and Cp, we illustrate that, in terms of risk function, no single PMSE dominates the others. The same conclusion holds more generally for any penalised likelihood information criterion. We also compare various model averaging schemes and show that no single one dominates the others in terms of risk function. Since PMSEs can be regarded as a special case of model averaging, with 0-1 random-weights, we propose a connection between the two theories, in the frequentist approach, by taking account of the selection procedure when performing model averaging. We illustrate the point by simulating a simple linear regression model.
Capillary Electrophoresis Sensitivity Enhancement Based on Adaptive Moving Average Method.
Drevinskas, Tomas; Telksnys, Laimutis; Maruška, Audrius; Gorbatsova, Jelena; Kaljurand, Mihkel
2018-06-05
In the present work, we demonstrate a novel approach to improve the sensitivity of the "out of lab" portable capillary electrophoretic measurements. Nowadays, many signal enhancement methods are (i) underused (nonoptimal), (ii) overused (distorts the data), or (iii) inapplicable in field-portable instrumentation because of a lack of computational power. The described innovative migration velocity-adaptive moving average method uses an optimal averaging window size and can be easily implemented with a microcontroller. The contactless conductivity detection was used as a model for the development of a signal processing method and the demonstration of its impact on the sensitivity. The frequency characteristics of the recorded electropherograms and peaks were clarified. Higher electrophoretic mobility analytes exhibit higher-frequency peaks, whereas lower electrophoretic mobility analytes exhibit lower-frequency peaks. On the basis of the obtained data, a migration velocity-adaptive moving average algorithm was created, adapted, and programmed into capillary electrophoresis data-processing software. Employing the developed algorithm, each data point is processed depending on a certain migration time of the analyte. Because of the implemented migration velocity-adaptive moving average method, the signal-to-noise ratio improved up to 11 times for sampling frequency of 4.6 Hz and up to 22 times for sampling frequency of 25 Hz. This paper could potentially be used as a methodological guideline for the development of new smoothing algorithms that require adaptive conditions in capillary electrophoresis and other separation methods.
Grade Point Average: What's Wrong and What's the Alternative?
Soh, Kay Cheng
2011-01-01
Grade point average (GPA) has been around for more than two centuries. However, it has created a lot of confusion, frustration, and anxiety to GPA-producers and users alike, especially when used across-nation for different purposes. This paper looks into the reasons for such a state of affairs from the perspective of educational measurement. It…
The Effect of Honors Courses on Grade Point Averages
Spisak, Art L.; Squires, Suzanne Carter
2016-01-01
High-ability entering college students give three main reasons for not choosing to become part of honors programs and colleges; they and/or their parents believe that honors classes at the university level require more work than non-honors courses, are more stressful, and will adversely affect their self-image and grade point average (GPA) (Hill;…
40 CFR 63.652 - Emissions averaging provisions.
2010-07-01
... emissions more than the reference control technology, but the combination of the pollution prevention... emissions average. This must include any Group 1 emission points to which the reference control technology... agrees has a higher nominal efficiency than the reference control technology. Information on the nominal...
An average salary: approaches to the index determination
Directory of Open Access Journals (Sweden)
T. M. Pozdnyakova
2017-01-01
Full Text Available The article “An average salary: approaches to the index determination” is devoted to studying various methods of calculating this index, both used by official state statistics of the Russian Federation and offered by modern researchers.The purpose of this research is to analyze the existing approaches to calculating the average salary of employees of enterprises and organizations, as well as to make certain additions that would help to clarify this index.The information base of the research is laws and regulations of the Russian Federation Government, statistical and analytical materials of the Federal State Statistics Service of Russia for the section «Socio-economic indexes: living standards of the population», as well as materials of scientific papers, describing different approaches to the average salary calculation. The data on the average salary of employees of educational institutions of the Khabarovsk region served as the experimental base of research. In the process of conducting the research, the following methods were used: analytical, statistical, calculated-mathematical and graphical.The main result of the research is an option of supplementing the method of calculating average salary index within enterprises or organizations, used by Goskomstat of Russia, by means of introducing a correction factor. Its essence consists in the specific formation of material indexes for different categories of employees in enterprises or organizations, mainly engaged in internal secondary jobs. The need for introducing this correction factor comes from the current reality of working conditions of a wide range of organizations, when an employee is forced, in addition to the main position, to fulfill additional job duties. As a result, the situation is frequent when the average salary at the enterprise is difficult to assess objectively because it consists of calculating multiple rates per staff member. In other words, the average salary of
Penkett, S.A.; Burgess, R.A.; Coe, H.; Coll, I.; Hov, O.; Lindskog, A.; Schmidbauer, N.; Solberg, S.; Roemer, M.; Thijsse, T.; Beck, J.; Reeves, C.E.
2007-01-01
The nitrate radical (NO3) was first measured in the atmosphere in the 1970s and suggestions were made that it could play a major role in oxidising many unsaturated hydrocarbons, such as those emitted from the biosphere. Analysis of the hydrocarbon mix over the North Atlantic Ocean suggested
Feeding behavior is an important component of growth and feed efficiency in swine. Acyl-ghrelin is a peptide produced in the stomach that is orexigenic. The role of ghrelin in regulating feeding behavior in swine under commercial conditions is unknown. The objectives of this study were to determine ...
High-average-power diode-pumped Yb: YAG lasers
International Nuclear Information System (INIS)
Avizonis, P V; Beach, R; Bibeau, C M; Emanuel, M A; Harris, D G; Honea, E C; Monroe, R S; Payne, S A; Skidmore, J A; Sutton, S B
1999-01-01
A scaleable diode end-pumping technology for high-average-power slab and rod lasers has been under development for the past several years at Lawrence Livermore National Laboratory (LLNL). This technology has particular application to high average power Yb:YAG lasers that utilize a rod configured gain element. Previously, this rod configured approach has achieved average output powers in a single 5 cm long by 2 mm diameter Yb:YAG rod of 430 W cw and 280 W q-switched. High beam quality (M(sup 2)= 2.4) q-switched operation has also been demonstrated at over 180 W of average output power. More recently, using a dual rod configuration consisting of two, 5 cm long by 2 mm diameter laser rods with birefringence compensation, we have achieved 1080 W of cw output with an M(sup 2) value of 13.5 at an optical-to-optical conversion efficiency of 27.5%. With the same dual rod laser operated in a q-switched mode, we have also demonstrated 532 W of average power with an M(sup 2) and lt; 2.5 at 17% optical-to-optical conversion efficiency. These q-switched results were obtained at a 10 kHz repetition rate and resulted in 77 nsec pulse durations. These improved levels of operational performance have been achieved as a result of technology advancements made in several areas that will be covered in this manuscript. These enhancements to our architecture include: (1) Hollow lens ducts that enable the use of advanced cavity architectures permitting birefringence compensation and the ability to run in large aperture-filling near-diffraction-limited modes. (2) Compound laser rods with flanged-nonabsorbing-endcaps fabricated by diffusion bonding. (3) Techniques for suppressing amplified spontaneous emission (ASE) and parasitics in the polished barrel rods
High average power diode pumped solid state lasers for CALIOPE
International Nuclear Information System (INIS)
Comaskey, B.; Halpin, J.; Moran, B.
1994-07-01
Diode pumping of solid state media offers the opportunity for very low maintenance, high efficiency, and compact laser systems. For remote sensing, such lasers may be used to pump tunable non-linear sources, or if tunable themselves, act directly or through harmonic crystals as the probe. The needs of long range remote sensing missions require laser performance in the several watts to kilowatts range. At these power performance levels, more advanced thermal management technologies are required for the diode pumps. The solid state laser design must now address a variety of issues arising from the thermal loads, including fracture limits, induced lensing and aberrations, induced birefringence, and laser cavity optical component performance degradation with average power loading. In order to highlight the design trade-offs involved in addressing the above issues, a variety of existing average power laser systems are briefly described. Included are two systems based on Spectra Diode Laboratory's water impingement cooled diode packages: a two times diffraction limited, 200 watt average power, 200 Hz multi-rod laser/amplifier by Fibertek, and TRW's 100 watt, 100 Hz, phase conjugated amplifier. The authors also present two laser systems built at Lawrence Livermore National Laboratory (LLNL) based on their more aggressive diode bar cooling package, which uses microchannel cooler technology capable of 100% duty factor operation. They then present the design of LLNL's first generation OPO pump laser for remote sensing. This system is specified to run at 100 Hz, 20 nsec pulses each with 300 mJ, less than two times diffraction limited, and with a stable single longitudinal mode. The performance of the first testbed version will be presented. The authors conclude with directions their group is pursuing to advance average power lasers. This includes average power electro-optics, low heat load lasing media, and heat capacity lasers
Construction of average adult Japanese voxel phantoms for dose assessment
International Nuclear Information System (INIS)
Sato, Kaoru; Takahashi, Fumiaki; Satoh, Daiki; Endo, Akira
2011-12-01
The International Commission on Radiological Protection (ICRP) adopted the adult reference voxel phantoms based on the physiological and anatomical reference data of Caucasian on October, 2007. The organs and tissues of these phantoms were segmented on the basis of ICRP Publication 103. In future, the dose coefficients for internal dose and dose conversion coefficients for external dose calculated using the adult reference voxel phantoms will be widely used for the radiation protection fields. On the other hand, the body sizes and organ masses of adult Japanese are generally smaller than those of adult Caucasian. In addition, there are some cases that the anatomical characteristics such as body sizes, organ masses and postures of subjects influence the organ doses in dose assessment for medical treatments and radiation accident. Therefore, it was needed to use human phantoms with average anatomical characteristics of Japanese. The authors constructed the averaged adult Japanese male and female voxel phantoms by modifying the previously developed high-resolution adult male (JM) and female (JF) voxel phantoms. It has been modified in the following three aspects: (1) The heights and weights were agreed with the Japanese averages; (2) The masses of organs and tissues were adjusted to the Japanese averages within 10%; (3) The organs and tissues, which were newly added for evaluation of the effective dose in ICRP Publication 103, were modeled. In this study, the organ masses, distances between organs, specific absorbed fractions (SAFs) and dose conversion coefficients of these phantoms were compared with those evaluated using the ICRP adult reference voxel phantoms. This report provides valuable information on the anatomical and dosimetric characteristics of the averaged adult Japanese male and female voxel phantoms developed as reference phantoms of adult Japanese. (author)
Erfanian, A.; Fomenko, L.; Wang, G.
2016-12-01
Multi-model ensemble (MME) average is considered the most reliable for simulating both present-day and future climates. It has been a primary reference for making conclusions in major coordinated studies i.e. IPCC Assessment Reports and CORDEX. The biases of individual models cancel out each other in MME average, enabling the ensemble mean to outperform individual members in simulating the mean climate. This enhancement however comes with tremendous computational cost, which is especially inhibiting for regional climate modeling as model uncertainties can originate from both RCMs and the driving GCMs. Here we propose the Ensemble-based Reconstructed Forcings (ERF) approach to regional climate modeling that achieves a similar level of bias reduction at a fraction of cost compared with the conventional MME approach. The new method constructs a single set of initial and boundary conditions (IBCs) by averaging the IBCs of multiple GCMs, and drives the RCM with this ensemble average of IBCs to conduct a single run. Using a regional climate model (RegCM4.3.4-CLM4.5), we tested the method over West Africa for multiple combination of (up to six) GCMs. Our results indicate that the performance of the ERF method is comparable to that of the MME average in simulating the mean climate. The bias reduction seen in ERF simulations is achieved by using more realistic IBCs in solving the system of equations underlying the RCM physics and dynamics. This endows the new method with a theoretical advantage in addition to reducing computational cost. The ERF output is an unaltered solution of the RCM as opposed to a climate state that might not be physically plausible due to the averaging of multiple solutions with the conventional MME approach. The ERF approach should be considered for use in major international efforts such as CORDEX. Key words: Multi-model ensemble, ensemble analysis, ERF, regional climate modeling
Energy Technology Data Exchange (ETDEWEB)
Hourdakis, C J, E-mail: khour@gaec.gr [Ionizing Radiation Calibration Laboratory-Greek Atomic Energy Commission, PO Box 60092, 15310 Agia Paraskevi, Athens, Attiki (Greece)
2011-04-07
The practical peak voltage (PPV) has been adopted as the reference measuring quantity for the x-ray tube voltage. However, the majority of commercial kV-meter models measure the average peak, U-bar{sub P}, the average, U-bar, the effective, U{sub eff} or the maximum peak, U{sub P} tube voltage. This work proposed a method for determination of the PPV from measurements with a kV-meter that measures the average U-bar or the average peak, U-bar{sub p} voltage. The kV-meter reading can be converted to the PPV by applying appropriate calibration coefficients and conversion factors. The average peak k{sub PPV,kVp} and the average k{sub PPV,Uav} conversion factors were calculated from virtual voltage waveforms for conventional diagnostic radiology (50-150 kV) and mammography (22-35 kV) tube voltages and for voltage ripples from 0% to 100%. Regression equation and coefficients provide the appropriate conversion factors at any given tube voltage and ripple. The influence of voltage waveform irregularities, like 'spikes' and pulse amplitude variations, on the conversion factors was investigated and discussed. The proposed method and the conversion factors were tested using six commercial kV-meters at several x-ray units. The deviations between the reference and the calculated - according to the proposed method - PPV values were less than 2%. Practical aspects on the voltage ripple measurement were addressed and discussed. The proposed method provides a rigorous base to determine the PPV with kV-meters from U-bar{sub p} and U-bar measurement. Users can benefit, since all kV-meters, irrespective of their measuring quantity, can be used to determine the PPV, complying with the IEC standard requirements.
Workplace Concentration of Immigrants
Andersson, Fredrik; García-Pérez, Mónica; Haltiwanger, John; McCue, Kristin; Sanders, Seth
2014-01-01
Casual observation suggests that in most U.S. urban labor markets, immigrants have more immigrant coworkers than native-born workers do. While seeming obvious, this excess tendency to work together has not been precisely measured, nor have its sources been quantified. Using matched employer–employee data from the U.S. Census Bureau Longitudinal Employer-Household Dynamics (LEHD) database on a set of metropolitan statistical areas (MSAs) with substantial immigrant populations, we find that, on average, 37% of an immigrant’s coworkers are themselves immigrants; in contrast, only 14% of a native-born worker’s coworkers are immigrants. We decompose this difference into the probability of working with compatriots versus with immigrants from other source countries. Using human capital, employer, and location characteristics, we narrow the mechanisms that might explain immigrant concentration. We find that industry, language, and residential segregation collectively explain almost all the excess tendency to work with immigrants from other source countries, but they have limited power to explain work with compatriots. This large unexplained compatriot component suggests an important role for unmeasured country-specific factors, such as social networks. PMID:25425452
The objective of this study was to determine the association of differentially expressed genes (DEG) in the jejunum of steers with average DMI and high or low ADG. Feed intake and growth were measured in a cohort of 144 commercial Angus steers consuming a finishing diet containing (on a DM basis) 67...
van Wee, B.; Rietveld, P.; Meurs, H.
2006-01-01
Recent research suggests that the average time spent travelling by the Dutch population has increased over the past decades. However, different data sources show different levels of increase. This paper explores possible causes for this increase. They include a rise in incomes, which has probably
On the time-averaging of ultrafine particle number size spectra in vehicular plumes
Directory of Open Access Journals (Sweden)
X. H. Yao
2006-01-01
Full Text Available Ultrafine vehicular particle (<100 nm number size distributions presented in the literature are mostly averages of long scan-time (~30 s or more spectra mainly due to the non-availability of commercial instruments that can measure particle distributions in the <10 nm to 100 nm range faster than 30 s even though individual researchers have built faster (1–2.5 s scanning instruments. With the introduction of the Engine Exhaust Particle Sizer (EEPS in 2004, high time-resolution (1 full 32-channel spectrum per second particle size distribution data become possible and allow atmospheric researchers to study the characteristics of ultrafine vehicular particles in rapidly and perhaps randomly varying high concentration environments such as roadside, on-road and tunnel. In this study, particle size distributions in these environments were found to vary as rapidly as one second frequently. This poses the question on the generality of using averages of long scan-time spectra for dynamic and/or mechanistic studies in rapidly and perhaps randomly varying high concentration environments. One-second EEPS data taken at roadside, on roads and in tunnels by a mobile platform are time-averaged to yield 5, 10, 30 and 120 s distributions to answer this question.
Multiple-level defect species evaluation from average carrier decay
Debuf, Didier
2003-10-01
An expression for the average decay is determined by solving the the carrier continuity equations, which include terms for multiple defect recombination. This expression is the decay measured by techniques such as the contactless photoconductance decay method, which determines the average or volume integrated decay. Implicit in the above is the requirement for good surface passivation such that only bulk properties are observed. A proposed experimental configuration is given to achieve the intended goal of an assessment of the type of defect in an n-type Czochralski-grown silicon semiconductor with an unusually high relative lifetime. The high lifetime is explained in terms of a ground excited state multiple-level defect system. Also, minority carrier trapping is investigated.
SEASONAL AVERAGE FLOW IN RÂUL NEGRU HYDROGRAPHIC BASIN
Directory of Open Access Journals (Sweden)
VIGH MELINDA
2015-03-01
Full Text Available The Râul Negru hydrographic basin is a well individualised physical-geographical unit inside the Braşov Depression. The flow is controlled by six hydrometric stations placed on the main river and on two important tributaries. The data base for seasonal flow analysis contains the discharges from 1950-2012. The results of data analysis show that there significant space-time differences between multiannual seasonal averages. Some interesting conclusions can be obtained by comparing abundant and scarce periods. Flow analysis was made using seasonal charts Q = f(T. The similarities come from the basin’s relative homogeneity, and the differences from flow’s evolution and trend. Flow variation is analysed using variation coefficient. In some cases appear significant Cv values differences. Also, Cv values trends are analysed according to basins’ average altitude.
A collisional-radiative average atom model for hot plasmas
International Nuclear Information System (INIS)
Rozsnyai, B.F.
1996-01-01
A collisional-radiative 'average atom' (AA) model is presented for the calculation of opacities of hot plasmas not in the condition of local thermodynamic equilibrium (LTE). The electron impact and radiative rate constants are calculated using the dipole oscillator strengths of the average atom. A key element of the model is the photon escape probability which at present is calculated for a semi infinite slab. The Fermi statistics renders the rate equation for the AA level occupancies nonlinear, which requires iterations until the steady state. AA level occupancies are found. Detailed electronic configurations are built into the model after the self-consistent non-LTE AA state is found. The model shows a continuous transition from the non-LTE to the LTE state depending on the optical thickness of the plasma. 22 refs., 13 figs., 1 tab
Kumaraswamy autoregressive moving average models for double bounded environmental data
Bayer, Fábio Mariano; Bayer, Débora Missio; Pumi, Guilherme
2017-12-01
In this paper we introduce the Kumaraswamy autoregressive moving average models (KARMA), which is a dynamic class of models for time series taking values in the double bounded interval (a,b) following the Kumaraswamy distribution. The Kumaraswamy family of distribution is widely applied in many areas, especially hydrology and related fields. Classical examples are time series representing rates and proportions observed over time. In the proposed KARMA model, the median is modeled by a dynamic structure containing autoregressive and moving average terms, time-varying regressors, unknown parameters and a link function. We introduce the new class of models and discuss conditional maximum likelihood estimation, hypothesis testing inference, diagnostic analysis and forecasting. In particular, we provide closed-form expressions for the conditional score vector and conditional Fisher information matrix. An application to environmental real data is presented and discussed.
Database of average-power damage thresholds at 1064 nm
International Nuclear Information System (INIS)
Rainer, F.; Hildum, E.A.; Milam, D.
1987-01-01
We have completed a database of average-power, laser-induced, damage thresholds at 1064 nm on a variety of materials. Measurements were made with a newly constructed laser to provide design input for moderate and high average-power laser projects. The measurements were conducted with 16-ns pulses at pulse-repetition frequencies ranging from 6 to 120 Hz. Samples were typically irradiated for time ranging from a fraction of a second up to 5 minutes (36,000 shots). We tested seven categories of samples which included antireflective coatings, high reflectors, polarizers, single and multiple layers of the same material, bare and overcoated metal surfaces, bare polished surfaces, and bulk materials. The measured damage threshold ranged from 2 for some metals to > 46 J/cm 2 for a bare polished glass substrate. 4 refs., 7 figs., 1 tab
Partial Averaged Navier-Stokes approach for cavitating flow
International Nuclear Information System (INIS)
Zhang, L; Zhang, Y N
2015-01-01
Partial Averaged Navier Stokes (PANS) is a numerical approach developed for studying practical engineering problems (e.g. cavitating flow inside hydroturbines) with a resonance cost and accuracy. One of the advantages of PANS is that it is suitable for any filter width, leading a bridging method from traditional Reynolds Averaged Navier-Stokes (RANS) to direct numerical simulations by choosing appropriate parameters. Comparing with RANS, the PANS model will inherit many physical nature from parent RANS but further resolve more scales of motion in great details, leading to PANS superior to RANS. As an important step for PANS approach, one need to identify appropriate physical filter-width control parameters e.g. ratios of unresolved-to-total kinetic energy and dissipation. In present paper, recent studies of cavitating flow based on PANS approach are introduced with a focus on the influences of filter-width control parameters on the simulation results
The B-dot Earth Average Magnetic Field
Capo-Lugo, Pedro A.; Rakoczy, John; Sanders, Devon
2013-01-01
The average Earth's magnetic field is solved with complex mathematical models based on mean square integral. Depending on the selection of the Earth magnetic model, the average Earth's magnetic field can have different solutions. This paper presents a simple technique that takes advantage of the damping effects of the b-dot controller and is not dependent of the Earth magnetic model; but it is dependent on the magnetic torquers of the satellite which is not taken into consideration in the known mathematical models. Also the solution of this new technique can be implemented so easily that the flight software can be updated during flight, and the control system can have current gains for the magnetic torquers. Finally, this technique is verified and validated using flight data from a satellite that it has been in orbit for three years.
Thermal effects in high average power optical parametric amplifiers.
Rothhardt, Jan; Demmler, Stefan; Hädrich, Steffen; Peschel, Thomas; Limpert, Jens; Tünnermann, Andreas
2013-03-01
Optical parametric amplifiers (OPAs) have the reputation of being average power scalable due to the instantaneous nature of the parametric process (zero quantum defect). This Letter reveals serious challenges originating from thermal load in the nonlinear crystal caused by absorption. We investigate these thermal effects in high average power OPAs based on beta barium borate. Absorption of both pump and idler waves is identified to contribute significantly to heating of the nonlinear crystal. A temperature increase of up to 148 K with respect to the environment is observed and mechanical tensile stress up to 40 MPa is found, indicating a high risk of crystal fracture under such conditions. By restricting the idler to a wavelength range far from absorption bands and removing the crystal coating we reduce the peak temperature and the resulting temperature gradient significantly. Guidelines for further power scaling of OPAs and other nonlinear devices are given.
Measuring average angular velocity with a smartphone magnetic field sensor
Pili, Unofre; Violanda, Renante
2018-02-01
The angular velocity of a spinning object is, by standard, measured using a device called a tachometer. However, by directly using it in a classroom setting, the activity is likely to appear as less instructive and less engaging. Indeed, some alternative classroom-suitable methods for measuring angular velocity have been presented. In this paper, we present a further alternative that is smartphone-based, making use of the real-time magnetic field (simply called B-field in what follows) data gathering capability of the B-field sensor of the smartphone device as the timer for measuring average rotational period and average angular velocity. The in-built B-field sensor in smartphones has already found a number of uses in undergraduate experimental physics. For instance, in elementary electrodynamics, it has been used to explore the well-known Bio-Savart law and in a measurement of the permeability of air.
Nuclear fuel management via fuel quality factor averaging
International Nuclear Information System (INIS)
Mingle, J.O.
1978-01-01
The numerical procedure of prime number averaging is applied to the fuel quality factor distribution of once and twice-burned fuel in order to evolve a fuel management scheme. The resulting fuel shuffling arrangement produces a near optimal flat power profile both under beginning-of-life and end-of-life conditions. The procedure is easily applied requiring only the solution of linear algebraic equations. (author)
Modeling methane emission via the infinite moving average process
Czech Academy of Sciences Publication Activity Database
Jordanova, D.; Dušek, Jiří; Stehlík, M.
2013-01-01
Roč. 122, - (2013), s. 40-49 ISSN 0169-7439 R&D Projects: GA MŠk(CZ) ED1.1.00/02.0073; GA ČR(CZ) GAP504/11/1151 Institutional support: RVO:67179843 Keywords : Environmental chemistry * Pareto tails * t-Hill estimator * Weak consistency * Moving average process * Methane emission model Subject RIV: EH - Ecology, Behaviour Impact factor: 2.381, year: 2013
Spatial analysis based on variance of moving window averages
Wu, B M; Subbarao, K V; Ferrandino, F J; Hao, J J
2006-01-01
A new method for analysing spatial patterns was designed based on the variance of moving window averages (VMWA), which can be directly calculated in geographical information systems or a spreadsheet program (e.g. MS Excel). Different types of artificial data were generated to test the method. Regardless of data types, the VMWA method correctly determined the mean cluster sizes. This method was also employed to assess spatial patterns in historical plant disease survey data encompassing both a...
Forecasting stock market averages to enhance profitable trading strategies
Haefke, Christian; Helmenstein, Christian
1995-01-01
In this paper we design a simple trading strategy to exploit the hypothesized distinct informational content of the arithmetic and geometric mean. The rejection of cointegration between the two stock market indicators supports this conjecture. The profits generated by this cheaply replicable trading scheme cannot be expected to persist. Therefore we forecast the averages using autoregressive linear and neural network models to gain a competitive advantage relative to other investors. Refining...
Application of NMR circuit for superconducting magnet using signal averaging
International Nuclear Information System (INIS)
Yamada, R.; Ishimoto, H.; Shea, M.F.; Schmidt, E.E.; Borer, K.
1977-01-01
An NMR circuit was used to measure the absolute field values of Fermilab Energy Doubler magnets up to 44 kG. A signal averaging method to improve the S/N ratio was implemented by means of a Tektronix Digital Processing Oscilloscope, followed by the development of an inexpensive microprocessor based system contained in a NIM module. Some of the data obtained from measuring two superconducting dipole magnets are presented
Average Case Analysis of Java 7's Dual Pivot Quicksort
Wild, Sebastian; Nebel, Markus E.
2013-01-01
Recently, a new Quicksort variant due to Yaroslavskiy was chosen as standard sorting method for Oracle's Java 7 runtime library. The decision for the change was based on empirical studies showing that on average, the new algorithm is faster than the formerly used classic Quicksort. Surprisingly, the improvement was achieved by using a dual pivot approach, an idea that was considered not promising by several theoretical studies in the past. In this paper, we identify the reason for this unexpe...
The definition and computation of average neutron lifetimes
International Nuclear Information System (INIS)
Henry, A.F.
1983-01-01
A precise physical definition is offered for a class of average lifetimes for neutrons in an assembly of materials, either multiplying or not, or if the former, critical or not. A compact theoretical expression for the general member of this class is derived in terms of solutions to the transport equation. Three specific definitions are considered. Particular exact expressions for these are derived and reduced to simple algebraic formulas for one-group and two-group homogeneous bare-core models
Marginal versus Average Beta of Equity under Corporate Taxation
Lund, Diderik
2009-01-01
Even for fully equity-financed firms there may be substantial effects of taxation on the after-tax cost of capital. Among the few studies of these effects, even fewer identify all effects correctly. When marginal investment is taxed together with inframarginal, marginal beta differs from average if there are investment-related deductions like depreciation. To calculate asset betas, one should not only 'unlever observed equity betas, but 'untax' and 'unaverage' them. Risky tax claims are value...
High average power solid state laser power conditioning system
International Nuclear Information System (INIS)
Steinkraus, R.F.
1987-01-01
The power conditioning system for the High Average Power Laser program at Lawrence Livermore National Laboratory (LLNL) is described. The system has been operational for two years. It is high voltage, high power, fault protected, and solid state. The power conditioning system drives flashlamps that pump solid state lasers. Flashlamps are driven by silicon control rectifier (SCR) switched, resonant charged, (LC) discharge pulse forming networks (PFNs). The system uses fiber optics for control and diagnostics. Energy and thermal diagnostics are monitored by computers
Minimal average consumption downlink base station power control strategy
Holtkamp H.; Auer G.; Haas H.
2011-01-01
We consider single cell multi-user OFDMA downlink resource allocation on a flat-fading channel such that average supply power is minimized while fulfilling a set of target rates. Available degrees of freedom are transmission power and duration. This paper extends our previous work on power optimal resource allocation in the mobile downlink by detailing the optimal power control strategy investigation and extracting fundamental characteristics of power optimal operation in cellular downlink. W...
Cosmological measure with volume averaging and the vacuum energy problem
Astashenok, Artyom V.; del Popolo, Antonino
2012-04-01
In this paper, we give a possible solution to the cosmological constant problem. It is shown that the traditional approach, based on volume weighting of probabilities, leads to an incoherent conclusion: the probability that a randomly chosen observer measures Λ = 0 is exactly equal to 1. Using an alternative, volume averaging measure, instead of volume weighting can explain why the cosmological constant is non-zero.
Cosmological measure with volume averaging and the vacuum energy problem
International Nuclear Information System (INIS)
Astashenok, Artyom V; Del Popolo, Antonino
2012-01-01
In this paper, we give a possible solution to the cosmological constant problem. It is shown that the traditional approach, based on volume weighting of probabilities, leads to an incoherent conclusion: the probability that a randomly chosen observer measures Λ = 0 is exactly equal to 1. Using an alternative, volume averaging measure, instead of volume weighting can explain why the cosmological constant is non-zero. (paper)
Average radiation weighting factors for specific distributed neutron spectra
International Nuclear Information System (INIS)
Ninkovic, M.M.; Raicevic, J.J.
1993-01-01
Spectrum averaged radiation weighting factors for 6 specific neutron fields in the environment of 3 categories of the neutron sources (fission, spontaneous fission and (α,n)) are determined in this paper. Obtained values of these factors are greater 1.5 to 2 times than the corresponding quality factors used for the same purpose until a few years ago. This fact is very important to have in mind in the conversion of the neutron fluence into the neutron dose equivalent. (author)
Calculating ensemble averaged descriptions of protein rigidity without sampling.
Directory of Open Access Journals (Sweden)
Luis C González
Full Text Available Previous works have demonstrated that protein rigidity is related to thermodynamic stability, especially under conditions that favor formation of native structure. Mechanical network rigidity properties of a single conformation are efficiently calculated using the integer body-bar Pebble Game (PG algorithm. However, thermodynamic properties require averaging over many samples from the ensemble of accessible conformations to accurately account for fluctuations in network topology. We have developed a mean field Virtual Pebble Game (VPG that represents the ensemble of networks by a single effective network. That is, all possible number of distance constraints (or bars that can form between a pair of rigid bodies is replaced by the average number. The resulting effective network is viewed as having weighted edges, where the weight of an edge quantifies its capacity to absorb degrees of freedom. The VPG is interpreted as a flow problem on this effective network, which eliminates the need to sample. Across a nonredundant dataset of 272 protein structures, we apply the VPG to proteins for the first time. Our results show numerically and visually that the rigidity characterizations of the VPG accurately reflect the ensemble averaged [Formula: see text] properties. This result positions the VPG as an efficient alternative to understand the mechanical role that chemical interactions play in maintaining protein stability.
Calculating ensemble averaged descriptions of protein rigidity without sampling.
González, Luis C; Wang, Hui; Livesay, Dennis R; Jacobs, Donald J
2012-01-01
Previous works have demonstrated that protein rigidity is related to thermodynamic stability, especially under conditions that favor formation of native structure. Mechanical network rigidity properties of a single conformation are efficiently calculated using the integer body-bar Pebble Game (PG) algorithm. However, thermodynamic properties require averaging over many samples from the ensemble of accessible conformations to accurately account for fluctuations in network topology. We have developed a mean field Virtual Pebble Game (VPG) that represents the ensemble of networks by a single effective network. That is, all possible number of distance constraints (or bars) that can form between a pair of rigid bodies is replaced by the average number. The resulting effective network is viewed as having weighted edges, where the weight of an edge quantifies its capacity to absorb degrees of freedom. The VPG is interpreted as a flow problem on this effective network, which eliminates the need to sample. Across a nonredundant dataset of 272 protein structures, we apply the VPG to proteins for the first time. Our results show numerically and visually that the rigidity characterizations of the VPG accurately reflect the ensemble averaged [Formula: see text] properties. This result positions the VPG as an efficient alternative to understand the mechanical role that chemical interactions play in maintaining protein stability.
High Average Power, High Energy Short Pulse Fiber Laser System
Energy Technology Data Exchange (ETDEWEB)
Messerly, M J
2007-11-13
Recently continuous wave fiber laser systems with output powers in excess of 500W with good beam quality have been demonstrated [1]. High energy, ultrafast, chirped pulsed fiber laser systems have achieved record output energies of 1mJ [2]. However, these high-energy systems have not been scaled beyond a few watts of average output power. Fiber laser systems are attractive for many applications because they offer the promise of high efficiency, compact, robust systems that are turn key. Applications such as cutting, drilling and materials processing, front end systems for high energy pulsed lasers (such as petawatts) and laser based sources of high spatial coherence, high flux x-rays all require high energy short pulses and two of the three of these applications also require high average power. The challenge in creating a high energy chirped pulse fiber laser system is to find a way to scale the output energy while avoiding nonlinear effects and maintaining good beam quality in the amplifier fiber. To this end, our 3-year LDRD program sought to demonstrate a high energy, high average power fiber laser system. This work included exploring designs of large mode area optical fiber amplifiers for high energy systems as well as understanding the issues associated chirped pulse amplification in optical fiber amplifier systems.
General and Local: Averaged k-Dependence Bayesian Classifiers
Directory of Open Access Journals (Sweden)
Limin Wang
2015-06-01
Full Text Available The inference of a general Bayesian network has been shown to be an NP-hard problem, even for approximate solutions. Although k-dependence Bayesian (KDB classifier can construct at arbitrary points (values of k along the attribute dependence spectrum, it cannot identify the changes of interdependencies when attributes take different values. Local KDB, which learns in the framework of KDB, is proposed in this study to describe the local dependencies implicated in each test instance. Based on the analysis of functional dependencies, substitution-elimination resolution, a new type of semi-naive Bayesian operation, is proposed to substitute or eliminate generalization to achieve accurate estimation of conditional probability distribution while reducing computational complexity. The final classifier, averaged k-dependence Bayesian (AKDB classifiers, will average the output of KDB and local KDB. Experimental results on the repository of machine learning databases from the University of California Irvine (UCI showed that AKDB has significant advantages in zero-one loss and bias relative to naive Bayes (NB, tree augmented naive Bayes (TAN, Averaged one-dependence estimators (AODE, and KDB. Moreover, KDB and local KDB show mutually complementary characteristics with respect to variance.
Quantized Average Consensus on Gossip Digraphs with Reduced Computation
Cai, Kai; Ishii, Hideaki
The authors have recently proposed a class of randomized gossip algorithms which solve the distributed averaging problem on directed graphs, with the constraint that each node has an integer-valued state. The essence of this algorithm is to maintain local records, called “surplus”, of individual state updates, thereby achieving quantized average consensus even though the state sum of all nodes is not preserved. In this paper we study a modified version of this algorithm, whose feature is primarily in reducing both computation and communication effort. Concretely, each node needs to update fewer local variables, and can transmit surplus by requiring only one bit. Under this modified algorithm we prove that reaching the average is ensured for arbitrary strongly connected graphs. The condition of arbitrary strong connection is less restrictive than those known in the literature for either real-valued or quantized states; in particular, it does not require the special structure on the network called balanced. Finally, we provide numerical examples to illustrate the convergence result, with emphasis on convergence time analysis.
Fitting a function to time-dependent ensemble averaged data.
Fogelmark, Karl; Lomholt, Michael A; Irbäck, Anders; Ambjörnsson, Tobias
2018-05-03
Time-dependent ensemble averages, i.e., trajectory-based averages of some observable, are of importance in many fields of science. A crucial objective when interpreting such data is to fit these averages (for instance, squared displacements) with a function and extract parameters (such as diffusion constants). A commonly overlooked challenge in such function fitting procedures is that fluctuations around mean values, by construction, exhibit temporal correlations. We show that the only available general purpose function fitting methods, correlated chi-square method and the weighted least squares method (which neglects correlation), fail at either robust parameter estimation or accurate error estimation. We remedy this by deriving a new closed-form error estimation formula for weighted least square fitting. The new formula uses the full covariance matrix, i.e., rigorously includes temporal correlations, but is free of the robustness issues, inherent to the correlated chi-square method. We demonstrate its accuracy in four examples of importance in many fields: Brownian motion, damped harmonic oscillation, fractional Brownian motion and continuous time random walks. We also successfully apply our method, weighted least squares including correlation in error estimation (WLS-ICE), to particle tracking data. The WLS-ICE method is applicable to arbitrary fit functions, and we provide a publically available WLS-ICE software.
Time-dependence and averaging techniques in atomic photoionization calculations
International Nuclear Information System (INIS)
Scheibner, K.F.
1984-01-01
Two distinct problems in the development and application of averaging techniques to photoionization calculations are considered. The first part of the thesis is concerned with the specific problem of near-resonant three-photon ionization in hydrogen, a process for which no cross section exists. Effects of the inclusion of the laser pulse characteristics (both temporal and spatial) on the dynamics of the ionization probability and of the metastable state probability are examined. It is found, for example, that the ionization probability can decrease with increasing field intensity. The temporal profile of the laser pulse is found to affect the dynamics very little, whereas the spatial character of the pulse can affect the results drastically. In the second part of the thesis techniques are developed for calculating averaged cross sections directly without first calculating a detailed cross section. Techniques are developed whereby the detailed cross section never has to be calculated as an intermediate step, but rather, the averaged cross section is calculated directly. A variation of the moment technique and a new method based on the stabilization technique are applied successfully to atomic hydrogen and helium
Ultra-low noise miniaturized neural amplifier with hardware averaging.
Dweiri, Yazan M; Eggers, Thomas; McCallum, Grant; Durand, Dominique M
2015-08-01
Peripheral nerves carry neural signals that could be used to control hybrid bionic systems. Cuff electrodes provide a robust and stable interface but the recorded signal amplitude is small (concept of hardware averaging to nerve recordings obtained with cuff electrodes. An optimization procedure is developed to minimize noise and power simultaneously. The novel design was based on existing neural amplifiers (Intan Technologies, LLC) and is validated with signals obtained from the FINE in chronic dog experiments. We showed that hardware averaging leads to a reduction in the total recording noise by a factor of 1/√N or less depending on the source resistance. Chronic recording of physiological activity with FINE using the presented design showed significant improvement on the recorded baseline noise with at least two parallel operation transconductance amplifiers leading to a 46.1% reduction at N = 8. The functionality of these recordings was quantified by the SNR improvement and shown to be significant for N = 3 or more. The present design was shown to be capable of generating hardware averaging on noise improvement for neural recording with cuff electrodes, and can accommodate the presence of high source impedances that are associated with the miniaturized contacts and the high channel count in electrode arrays. This technique can be adopted for other applications where miniaturized and implantable multichannel acquisition systems with ultra-low noise and low power are required.
He, Ning; Sun, Hechun; Dai, Miaomiao
2014-05-01
To evaluate the influence of temperature and humidity on the drug stability by initial average rate experiment, and to obtained the kinetic parameters. The effect of concentration error, drug degradation extent, humidity and temperature numbers, humidity and temperature range, and average humidity and temperature on the accuracy and precision of kinetic parameters in the initial average rate experiment was explored. The stability of vitamin C, as a solid state model, was investigated by an initial average rate experiment. Under the same experimental conditions, the kinetic parameters obtained from this proposed method were comparable to those from classical isothermal experiment at constant humidity. The estimates were more accurate and precise by controlling the extent of drug degradation, changing humidity and temperature range, or by setting the average temperature closer to room temperature. Compared with isothermal experiments at constant humidity, our proposed method saves time, labor, and materials.
Local and average structure of Mn- and La-substituted BiFeO3
Jiang, Bo; Selbach, Sverre M.
2017-06-01
The local and average structure of solid solutions of the multiferroic perovskite BiFeO3 is investigated by synchrotron X-ray diffraction (XRD) and electron density functional theory (DFT) calculations. The average experimental structure is determined by Rietveld refinement and the local structure by total scattering data analyzed in real space with the pair distribution function (PDF) method. With equal concentrations of La on the Bi site or Mn on the Fe site, La causes larger structural distortions than Mn. Structural models based on DFT relaxed geometry give an improved fit to experimental PDFs compared to models constrained by the space group symmetry. Berry phase calculations predict a higher ferroelectric polarization than the experimental literature values, reflecting that structural disorder is not captured in either average structure space group models or DFT calculations with artificial long range order imposed by periodic boundary conditions. Only by including point defects in a supercell, here Bi vacancies, can DFT calculations reproduce the literature results on the structure and ferroelectric polarization of Mn-substituted BiFeO3. The combination of local and average structure sensitive experimental methods with DFT calculations is useful for illuminating the structure-property-composition relationships in complex functional oxides with local structural distortions.
Lowest-order average effect of turbulence on atmospheric profiles derived from radio occultation
International Nuclear Information System (INIS)
Eshleman, V.R.; Haugstad, B.S.
1977-01-01
Turbulence in planetary atmospheres and ionospheres causes changes in angles of refraction of radio waves used in occultation experiments. Atmospheric temperature and pressure profiles, and ionospheric electron concentration profiles, derived from radio occultation measurements of Doppler frequency contain errors due to such angular offsets. The lowest-order average errors are derived from a geometrical-optics treatment of the radio-wave phase advance caused by the addition of uniform turbulence to an initially homogeneous medium. It is concluded that the average profile errors are small and that precise Doppler frequency measurements at two or more wavelengths could be used to help determine characteristics of the turbulence, as well as accuracy limits and possible correction terms for the profiles. However, a more detailed study of both frequency and intensity characteristics in radio and optical occultation measurements of turbulent planetary atmospheres and ionospheres is required to realize the full potential of such measurements
Calculations of the properties of superconducting alloys via the average T-matrix approximation
International Nuclear Information System (INIS)
Chatterjee, P.
1980-01-01
The theoretical formula of McMillan, modified via the multiple-scattering theory by Gomersall and Gyorffy, has been very successful in computing the electron-phonon coupling constant (lambda) and the transition temperature (Tsub(c)) of many superconducting elements and compounds. For disordered solids, such as substitutional alloys, however, this theory fails because of the breakdown of the translational symmetry used in the multiple-scattering theory. Under these conditions the problem can still be solved if the t-matrix is averaged in the random phase approximation (average T-matrix approximation). Gomersall and Gyorffy's expression is reformulated for lambda in the random phase approximation. This theory is applied to calculate lambda and Tsub(c) of the binary substitutional NbMo alloy system at different concentrations. The results appear to be in fair agreement with experiments. (author)
Wolthaus, J W H; Sonke, J J; van Herk, M; Damen, E M F
2008-09-01
novel method to create a midposition CT scan (time-weighted average of the anatomy) for treatment planning with reduced noise and artifacts was introduced. Tumor shape and position in the MidP CT scan represents that of the BH CT scan better than MidV CT scan and, therefore, was found to be appropriate for treatment planning.
Lovreglio, Piero; Maffei, Francesca; Carrieri, Mariella; D'Errico, Maria N; Drago, Ignazio; Hrelia, Patrizia; Bartolucci, Giovanni B; Soleo, Leonardo
2014-08-01
The frequency of chromosome aberrations (CA) and micronuclei (MN) was investigated in the peripheral lymphocytes of workers occupationally exposed to low or very low concentrations of benzene. The study included 43 exposed workers (all males), namely 19 fuel-tanker drivers and 24 filling-station attendants, and 31 male subjects with no occupational exposure to the toxicant (controls). Benzene exposure was verified by means of environmental monitoring with passive personal samplers (Radiello(®)), and through biological monitoring, i.e. by measurement of urinary trans,trans-muconic acid, S-phenylmercapturic acid and benzene. The frequency of CA and MN in peripheral lymphocytes was determined according to standard procedures. Exposure to benzene was found to be significantly higher for fuel-tanker drivers (median 246.6 μg/m(3)) than for filling-station attendants (median 19.9 μg/m(3)). Both groups had significantly higher exposure than controls (median 4.3 μg/m(3)). No increased frequency of CA and MN was observed in either fuel-tanker drivers or filling-station attendants compared with controls. In all subjects examined as a single group, the frequency of MN was significantly dependent on age. Only in the fuel-tanker drivers was the frequency of MN found to depend not only on age, but also on exposure to benzene. In conclusion, the frequency of MN, but not of CA, could be influenced by exposure to benzene concentrations of up to one order of magnitude lower than the threshold limit value (time-weighted average). Copyright © 2014 Elsevier B.V. All rights reserved.
Constructive Epistemic Modeling: A Hierarchical Bayesian Model Averaging Method
Tsai, F. T. C.; Elshall, A. S.
2014-12-01
Constructive epistemic modeling is the idea that our understanding of a natural system through a scientific model is a mental construct that continually develops through learning about and from the model. Using the hierarchical Bayesian model averaging (HBMA) method [1], this study shows that segregating different uncertain model components through a BMA tree of posterior model probabilities, model prediction, within-model variance, between-model variance and total model variance serves as a learning tool [2]. First, the BMA tree of posterior model probabilities permits the comparative evaluation of the candidate propositions of each uncertain model component. Second, systemic model dissection is imperative for understanding the individual contribution of each uncertain model component to the model prediction and variance. Third, the hierarchical representation of the between-model variance facilitates the prioritization of the contribution of each uncertain model component to the overall model uncertainty. We illustrate these concepts using the groundwater modeling of a siliciclastic aquifer-fault system. The sources of uncertainty considered are from geological architecture, formation dip, boundary conditions and model parameters. The study shows that the HBMA analysis helps in advancing knowledge about the model rather than forcing the model to fit a particularly understanding or merely averaging several candidate models. [1] Tsai, F. T.-C., and A. S. Elshall (2013), Hierarchical Bayesian model averaging for hydrostratigraphic modeling: Uncertainty segregation and comparative evaluation. Water Resources Research, 49, 5520-5536, doi:10.1002/wrcr.20428. [2] Elshall, A.S., and F. T.-C. Tsai (2014). Constructive epistemic modeling of groundwater flow with geological architecture and boundary condition uncertainty under Bayesian paradigm, Journal of Hydrology, 517, 105-119, doi: 10.1016/j.jhydrol.2014.05.027.
Artificial Intelligence Can Predict Daily Trauma Volume and Average Acuity.
Stonko, David P; Dennis, Bradley M; Betzold, Richard D; Peetz, Allan B; Gunter, Oliver L; Guillamondegui, Oscar D
2018-04-19
The goal of this study was to integrate temporal and weather data in order to create an artificial neural network (ANN) to predict trauma volume, the number of emergent operative cases, and average daily acuity at a level 1 trauma center. Trauma admission data from TRACS and weather data from the National Oceanic and Atmospheric Administration (NOAA) was collected for all adult trauma patients from July 2013-June 2016. The ANN was constructed using temporal (time, day of week), and weather factors (daily high, active precipitation) to predict four points of daily trauma activity: number of traumas, number of penetrating traumas, average ISS, and number of immediate OR cases per day. We trained a two-layer feed-forward network with 10 sigmoid hidden neurons via the Levenberg-Marquardt backpropagation algorithm, and performed k-fold cross validation and accuracy calculations on 100 randomly generated partitions. 10,612 patients over 1,096 days were identified. The ANN accurately predicted the daily trauma distribution in terms of number of traumas, number of penetrating traumas, number of OR cases, and average daily ISS (combined training correlation coefficient r = 0.9018+/-0.002; validation r = 0.8899+/- 0.005; testing r = 0.8940+/-0.006). We were able to successfully predict trauma and emergent operative volume, and acuity using an ANN by integrating local weather and trauma admission data from a level 1 center. As an example, for June 30, 2016, it predicted 9.93 traumas (actual: 10), and a mean ISS score of 15.99 (actual: 13.12); see figure 3. This may prove useful for predicting trauma needs across the system and hospital administration when allocating limited resources. Level III STUDY TYPE: Prognostic/Epidemiological.
Exploring JLA supernova data with improved flux-averaging technique
Energy Technology Data Exchange (ETDEWEB)
Wang, Shuang; Wen, Sixiang; Li, Miao, E-mail: wangshuang@mail.sysu.edu.cn, E-mail: wensx@mail2.sysu.edu.cn, E-mail: limiao9@mail.sysu.edu.cn [School of Physics and Astronomy, Sun Yat-Sen University, University Road (No. 2), Zhuhai (China)
2017-03-01
In this work, we explore the cosmological consequences of the ''Joint Light-curve Analysis'' (JLA) supernova (SN) data by using an improved flux-averaging (FA) technique, in which only the type Ia supernovae (SNe Ia) at high redshift are flux-averaged. Adopting the criterion of figure of Merit (FoM) and considering six dark energy (DE) parameterizations, we search the best FA recipe that gives the tightest DE constraints in the ( z {sub cut}, Δ z ) plane, where z {sub cut} and Δ z are redshift cut-off and redshift interval of FA, respectively. Then, based on the best FA recipe obtained, we discuss the impacts of varying z {sub cut} and varying Δ z , revisit the evolution of SN color luminosity parameter β, and study the effects of adopting different FA recipe on parameter estimation. We find that: (1) The best FA recipe is ( z {sub cut} = 0.6, Δ z =0.06), which is insensitive to a specific DE parameterization. (2) Flux-averaging JLA samples at z {sub cut} ≥ 0.4 will yield tighter DE constraints than the case without using FA. (3) Using FA can significantly reduce the redshift-evolution of β. (4) The best FA recipe favors a larger fractional matter density Ω {sub m} . In summary, we present an alternative method of dealing with JLA data, which can reduce the systematic uncertainties of SNe Ia and give the tighter DE constraints at the same time. Our method will be useful in the use of SNe Ia data for precision cosmology.
Radial behavior of the average local ionization energies of atoms
International Nuclear Information System (INIS)
Politzer, P.; Murray, J.S.; Grice, M.E.; Brinck, T.; Ranganathan, S.
1991-01-01
The radial behavior of the average local ionization energy bar I(r) has been investigated for the atoms He--Kr, using ab initio Hartree--Fock atomic wave functions. bar I(r) is found to decrease in a stepwise manner with the inflection points serving effectively to define boundaries between electronic shells. There is a good inverse correlation between polarizability and the ionization energy in the outermost region of the atom, suggesting that bar I(r) may be a meaningful measure of local polarizabilities in atoms and molecules
Average-case analysis of incremental topological ordering
DEFF Research Database (Denmark)
Ajwani, Deepak; Friedrich, Tobias
2010-01-01
Many applications like pointer analysis and incremental compilation require maintaining a topological ordering of the nodes of a directed acyclic graph (DAG) under dynamic updates. All known algorithms for this problem are either only analyzed for worst-case insertion sequences or only evaluated...... experimentally on random DAGs. We present the first average-case analysis of incremental topological ordering algorithms. We prove an expected runtime of under insertion of the edges of a complete DAG in a random order for the algorithms of Alpern et al. (1990) [4], Katriel and Bodlaender (2006) [18], and Pearce...
Fast Decentralized Averaging via Multi-scale Gossip
Tsianos, Konstantinos I.; Rabbat, Michael G.
We are interested in the problem of computing the average consensus in a distributed fashion on random geometric graphs. We describe a new algorithm called Multi-scale Gossip which employs a hierarchical decomposition of the graph to partition the computation into tractable sub-problems. Using only pairwise messages of fixed size that travel at most O(n^{1/3}) hops, our algorithm is robust and has communication cost of O(n loglogn logɛ - 1) transmissions, which is order-optimal up to the logarithmic factor in n. Simulated experiments verify the good expected performance on graphs of many thousands of nodes.
Edgeworth expansion for the pre-averaging estimator
DEFF Research Database (Denmark)
Podolskij, Mark; Veliyev, Bezirgen; Yoshida, Nakahiro
In this paper, we study the Edgeworth expansion for a pre-averaging estimator of quadratic variation in the framework of continuous diffusion models observed with noise. More specifically, we obtain a second order expansion for the joint density of the estimators of quadratic variation and its...... asymptotic variance. Our approach is based on martingale embedding, Malliavin calculus and stable central limit theorems for continuous diffusions. Moreover, we derive the density expansion for the studentized statistic, which might be applied to construct asymptotic confidence regions....
Analysis of nonlinear systems using ARMA [autoregressive moving average] models
International Nuclear Information System (INIS)
Hunter, N.F. Jr.
1990-01-01
While many vibration systems exhibit primarily linear behavior, a significant percentage of the systems encountered in vibration and model testing are mildly to severely nonlinear. Analysis methods for such nonlinear systems are not yet well developed and the response of such systems is not accurately predicted by linear models. Nonlinear ARMA (autoregressive moving average) models are one method for the analysis and response prediction of nonlinear vibratory systems. In this paper we review the background of linear and nonlinear ARMA models, and illustrate the application of these models to nonlinear vibration systems. We conclude by summarizing the advantages and disadvantages of ARMA models and emphasizing prospects for future development. 14 refs., 11 figs
Application of autoregressive moving average model in reactor noise analysis
International Nuclear Information System (INIS)
Tran Dinh Tri
1993-01-01
The application of an autoregressive (AR) model to estimating noise measurements has achieved many successes in reactor noise analysis in the last ten years. The physical processes that take place in the nuclear reactor, however, are described by an autoregressive moving average (ARMA) model rather than by an AR model. Consequently more correct results could be obtained by applying the ARMA model instead of the AR model to reactor noise analysis. In this paper the system of the generalised Yule-Walker equations is derived from the equation of an ARMA model, then a method for its solution is given. Numerical results show the applications of the method proposed. (author)
Effect of random edge failure on the average path length
Energy Technology Data Exchange (ETDEWEB)
Guo Dongchao; Liang Mangui; Li Dandan; Jiang Zhongyuan, E-mail: mgliang58@gmail.com, E-mail: 08112070@bjtu.edu.cn [Institute of Information Science, Beijing Jiaotong University, 100044, Beijing (China)
2011-10-14
We study the effect of random removal of edges on the average path length (APL) in a large class of uncorrelated random networks in which vertices are characterized by hidden variables controlling the attachment of edges between pairs of vertices. A formula for approximating the APL of networks suffering random edge removal is derived first. Then, the formula is confirmed by simulations for classical ER (Erdoes and Renyi) random graphs, BA (Barabasi and Albert) networks, networks with exponential degree distributions as well as random networks with asymptotic power-law degree distributions with exponent {alpha} > 2. (paper)
Generalized Heteroskedasticity ACF for Moving Average Models in Explicit Forms
Samir Khaled Safi
2014-01-01
The autocorrelation function (ACF) measures the correlation between observations at different distances apart. We derive explicit equations for generalized heteroskedasticity ACF for moving average of order q, MA(q). We consider two cases: Firstly: when the disturbance term follow the general covariance matrix structure Cov(wi, wj)=S with si,j ¹ 0 " i¹j . Secondly: when the diagonal elements of S are not all identical but sij = 0 " i¹j, i.e. S=diag(s11, s22,&hellip...
Nongeostrophic theory of zonally averaged circulation. I - Formulation
Tung, Ka Kit
1986-01-01
A nongeostrophic theory of zonally averaged circulation is formulated using the nonlinear primitive equations (mass conservation, thermodynamics, and zonal momentum) on a sphere. The relationship between the mean meridional circulation and diabatic heating rate is studied. Differences between results of nongeostropic theory and the geostrophic formulation concerning the role of eddy forcing of the diabatic circulation and the nonlinear nearly inviscid limit versus the geostrophic limit are discussed. Consideration is given to the Eliassen-Palm flux divergence, the Eliassen-Palm pseudodivergence, the nonacceleration theorem, and the nonlinear nongeostrophic Taylor relationship.
Average methods and their applications in Differential Geometry I
Vincze, Csaba
2013-01-01
In Minkowski geometry the metric features are based on a compact convex body containing the origin in its interior. This body works as a unit ball with its boundary formed by the unit vectors. Using one-homogeneous extension we have a so-called Minkowski functional to measure the lenght of vectors. The half of its square is called the energy function. Under some regularity conditions we can introduce an average Euclidean inner product by integrating the Hessian matrix of the energy function o...
Matrix product approach for the asymmetric random average process
International Nuclear Information System (INIS)
Zielen, F; Schadschneider, A
2003-01-01
We consider the asymmetric random average process which is a one-dimensional stochastic lattice model with nearest-neighbour interaction but continuous and unbounded state variables. First, the explicit functional representations, so-called beta densities, of all local interactions leading to steady states of product measure form are rigorously derived. This also completes an outstanding proof given in a previous publication. Then we present an alternative solution for the processes with factorized stationary states by using a matrix product ansatz. Due to continuous state variables we obtain a matrix algebra in the form of a functional equation which can be solved exactly
Low Average Sidelobe Slot Array Antennas for Radiometer Applications
Rengarajan, Sembiam; Zawardzki, Mark S.; Hodges, Richard E.
2012-01-01
In radiometer applications, it is required to design antennas that meet low average sidelobe levels and low average return loss over a specified frequency bandwidth. It is a challenge to meet such specifications over a frequency range when one uses resonant elements such as waveguide feed slots. In addition to their inherent narrow frequency band performance, the problem is exacerbated due to modeling errors and manufacturing tolerances. There was a need to develop a design methodology to solve the problem. An iterative design procedure was developed by starting with an array architecture, lattice spacing, aperture distribution, waveguide dimensions, etc. The array was designed using Elliott s technique with appropriate values of the total slot conductance in each radiating waveguide, and the total resistance in each feed waveguide. Subsequently, the array performance was analyzed by the full wave method of moments solution to the pertinent integral equations. Monte Carlo simulations were also carried out to account for amplitude and phase errors introduced for the aperture distribution due to modeling errors as well as manufacturing tolerances. If the design margins for the average sidelobe level and the average return loss were not adequate, array architecture, lattice spacing, aperture distribution, and waveguide dimensions were varied in subsequent iterations. Once the design margins were found to be adequate, the iteration was stopped and a good design was achieved. A symmetric array architecture was found to meet the design specification with adequate margin. The specifications were near 40 dB for angular regions beyond 30 degrees from broadside. Separable Taylor distribution with nbar=4 and 35 dB sidelobe specification was chosen for each principal plane. A non-separable distribution obtained by the genetic algorithm was found to have similar characteristics. The element spacing was obtained to provide the required beamwidth and close to a null in the E
Stochastic Optimal Prediction with Application to Averaged Euler Equations
Energy Technology Data Exchange (ETDEWEB)
Bell, John [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Chorin, Alexandre J. [Univ. of California, Berkeley, CA (United States); Crutchfield, William [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)
2017-04-24
Optimal prediction (OP) methods compensate for a lack of resolution in the numerical solution of complex problems through the use of an invariant measure as a prior measure in the Bayesian sense. In first-order OP, unresolved information is approximated by its conditional expectation with respect to the invariant measure. In higher-order OP, unresolved information is approximated by a stochastic estimator, leading to a system of random or stochastic differential equations. We explain the ideas through a simple example, and then apply them to the solution of Averaged Euler equations in two space dimensions.
Glycogen with short average chain length enhances bacterial durability
Wang, Liang; Wise, Michael J.
2011-09-01
Glycogen is conventionally viewed as an energy reserve that can be rapidly mobilized for ATP production in higher organisms. However, several studies have noted that glycogen with short average chain length in some bacteria is degraded very slowly. In addition, slow utilization of glycogen is correlated with bacterial viability, that is, the slower the glycogen breakdown rate, the longer the bacterial survival time in the external environment under starvation conditions. We call that a durable energy storage mechanism (DESM). In this review, evidence from microbiology, biochemistry, and molecular biology will be assembled to support the hypothesis of glycogen as a durable energy storage compound. One method for testing the DESM hypothesis is proposed.
Characterizing individual painDETECT symptoms by average pain severity
Directory of Open Access Journals (Sweden)
Sadosky A
2016-07-01
Full Text Available Alesia Sadosky,1 Vijaya Koduru,2 E Jay Bienen,3 Joseph C Cappelleri4 1Pfizer Inc, New York, NY, 2Eliassen Group, New London, CT, 3Outcomes Research Consultant, New York, NY, 4Pfizer Inc, Groton, CT, USA Background: painDETECT is a screening measure for neuropathic pain. The nine-item version consists of seven sensory items (burning, tingling/prickling, light touching, sudden pain attacks/electric shock-type pain, cold/heat, numbness, and slight pressure, a pain course pattern item, and a pain radiation item. The seven-item version consists only of the sensory items. Total scores of both versions discriminate average pain-severity levels (mild, moderate, and severe, but their ability to discriminate individual item severity has not been evaluated.Methods: Data were from a cross-sectional, observational study of six neuropathic pain conditions (N=624. Average pain severity was evaluated using the Brief Pain Inventory-Short Form, with severity levels defined using established cut points for distinguishing mild, moderate, and severe pain. The Wilcoxon rank sum test was followed by ridit analysis to represent the probability that a randomly selected subject from one average pain-severity level had a more favorable outcome on the specific painDETECT item relative to a randomly selected subject from a comparator severity level.Results: A probability >50% for a better outcome (less severe pain was significantly observed for each pain symptom item. The lowest probability was 56.3% (on numbness for mild vs moderate pain and highest probability was 76.4% (on cold/heat for mild vs severe pain. The pain radiation item was significant (P<0.05 and consistent with pain symptoms, as well as with total scores for both painDETECT versions; only the pain course item did not differ.Conclusion: painDETECT differentiates severity such that the ability to discriminate average pain also distinguishes individual pain item severity in an interpretable manner. Pain
Image Denoising Using Interquartile Range Filter with Local Averaging
Jassim, Firas Ajil
2013-01-01
Image denoising is one of the fundamental problems in image processing. In this paper, a novel approach to suppress noise from the image is conducted by applying the interquartile range (IQR) which is one of the statistical methods used to detect outlier effect from a dataset. A window of size kXk was implemented to support IQR filter. Each pixel outside the IQR range of the kXk window is treated as noisy pixel. The estimation of the noisy pixels was obtained by local averaging. The essential...
Updated precision measurement of the average lifetime of B hadrons
Abreu, P; Adye, T; Agasi, E; Ajinenko, I; Aleksan, Roy; Alekseev, G D; Alemany, R; Allport, P P; Almehed, S; Amaldi, Ugo; Amato, S; Andreazza, A; Andrieux, M L; Antilogus, P; Apel, W D; Arnoud, Y; Åsman, B; Augustin, J E; Augustinus, A; Baillon, Paul; Bambade, P; Barate, R; Barbi, M S; Barbiellini, Guido; Bardin, Dimitri Yuri; Baroncelli, A; Bärring, O; Barrio, J A; Bartl, Walter; Bates, M J; Battaglia, Marco; Baubillier, M; Baudot, J; Becks, K H; Begalli, M; Beillière, P; Belokopytov, Yu A; Benvenuti, Alberto C; Berggren, M; Bertrand, D; Bianchi, F; Bigi, M; Bilenky, S M; Billoir, P; Bloch, D; Blume, M; Blyth, S; Bolognese, T; Bonesini, M; Bonivento, W; Booth, P S L; Borisov, G; Bosio, C; Bosworth, S; Botner, O; Boudinov, E; Bouquet, B; Bourdarios, C; Bowcock, T J V; Bozzo, M; Branchini, P; Brand, K D; Brenke, T; Brenner, R A; Bricman, C; Brillault, L; Brown, R C A; Brückman, P; Brunet, J M; Bugge, L; Buran, T; Burgsmüller, T; Buschmann, P; Buys, A; Cabrera, S; Caccia, M; Calvi, M; Camacho-Rozas, A J; Camporesi, T; Canale, V; Canepa, M; Cankocak, K; Cao, F; Carena, F; Carroll, L; Caso, Carlo; Castillo-Gimenez, M V; Cattai, A; Cavallo, F R; Cerrito, L; Chabaud, V; Charpentier, P; Chaussard, L; Chauveau, J; Checchia, P; Chelkov, G A; Chen, M; Chierici, R; Chliapnikov, P V; Chochula, P; Chorowicz, V; Chudoba, J; Cindro, V; Collins, P; Contreras, J L; Contri, R; Cortina, E; Cosme, G; Cossutti, F; Crawley, H B; Crennell, D J; Crosetti, G; Cuevas-Maestro, J; Czellar, S; Dahl-Jensen, Erik; Dahm, J; D'Almagne, B; Dam, M; Damgaard, G; Dauncey, P D; Davenport, Martyn; Da Silva, W; Defoix, C; Deghorain, A; Della Ricca, G; Delpierre, P A; Demaria, N; De Angelis, A; de Boer, Wim; De Brabandere, S; De Clercq, C; La Vaissière, C de; De Lotto, B; De Min, A; De Paula, L S; De Saint-Jean, C; Dijkstra, H; Di Ciaccio, Lucia; Djama, F; Dolbeau, J; Dönszelmann, M; Doroba, K; Dracos, M; Drees, J; Drees, K A; Dris, M; Dufour, Y; Edsall, D M; Ehret, R; Eigen, G; Ekelöf, T J C; Ekspong, Gösta; Elsing, M; Engel, J P; Ershaidat, N; Erzen, B; Espirito-Santo, M C; Falk, E; Fassouliotis, D; Feindt, Michael; Fenyuk, A; Ferrer, A; Filippas-Tassos, A; Firestone, A; Fischer, P A; Föth, H; Fokitis, E; Fontanelli, F; Formenti, F; Franek, B J; Frenkiel, P; Fries, D E C; Frodesen, A G; Frühwirth, R; Fulda-Quenzer, F; Fuster, J A; Galloni, A; Gamba, D; Gandelman, M; García, C; García, J; Gaspar, C; Gasparini, U; Gavillet, P; Gazis, E N; Gelé, D; Gerber, J P; Gibbs, M; Gokieli, R; Golob, B; Gopal, Gian P; Gorn, L; Górski, M; Guz, Yu; Gracco, Valerio; Graziani, E; Grosdidier, G; Grzelak, K; Gumenyuk, S A; Gunnarsson, P; Günther, M; Guy, J; Hahn, F; Hahn, S; Hajduk, Z; Hallgren, A; Hamacher, K; Hao, W; Harris, F J; Hedberg, V; Henriques, R P; Hernández, J J; Herquet, P; Herr, H; Hessing, T L; Higón, E; Hilke, Hans Jürgen; Hill, T S; Holmgren, S O; Holt, P J; Holthuizen, D J; Hoorelbeke, S; Houlden, M A; Hrubec, Josef; Huet, K; Hultqvist, K; Jackson, J N; Jacobsson, R; Jalocha, P; Janik, R; Jarlskog, C; Jarlskog, G; Jarry, P; Jean-Marie, B; Johansson, E K; Jönsson, L B; Jönsson, P E; Joram, Christian; Juillot, P; Kaiser, M; Kapusta, F; Karafasoulis, K; Karlsson, M; Karvelas, E; Katsanevas, S; Katsoufis, E C; Keränen, R; Khokhlov, Yu A; Khomenko, B A; Khovanskii, N N; King, B J; Kjaer, N J; Klein, H; Klovning, A; Kluit, P M; Köne, B; Kokkinias, P; Koratzinos, M; Korcyl, K; Kourkoumelis, C; Kuznetsov, O; Kramer, P H; Krammer, Manfred; Kreuter, C; Kronkvist, I J; Krumshtein, Z; Krupinski, W; Kubinec, P; Kucewicz, W; Kurvinen, K L; Lacasta, C; Laktineh, I; Lamblot, S; Lamsa, J; Lanceri, L; Lane, D W; Langefeld, P; Last, I; Laugier, J P; Lauhakangas, R; Leder, Gerhard; Ledroit, F; Lefébure, V; Legan, C K; Leitner, R; Lemoigne, Y; Lemonne, J; Lenzen, Georg; Lepeltier, V; Lesiak, T; Liko, D; Lindner, R; Lipniacka, A; Lippi, I; Lörstad, B; Loken, J G; López, J M; Loukas, D; Lutz, P; Lyons, L; MacNaughton, J N; Maehlum, G; Maio, A; Malychev, V; Mandl, F; Marco, J; Marco, R P; Maréchal, B; Margoni, M; Marin, J C; Mariotti, C; Markou, A; Maron, T; Martínez-Rivero, C; Martínez-Vidal, F; Martí i García, S; Masik, J; Matorras, F; Matteuzzi, C; Matthiae, Giorgio; Mazzucato, M; McCubbin, M L; McKay, R; McNulty, R; Medbo, J; Merk, M; Meroni, C; Meyer, S; Meyer, W T; Michelotto, M; Migliore, E; Mirabito, L; Mitaroff, Winfried A; Mjörnmark, U; Moa, T; Møller, R; Mönig, K; Monge, M R; Morettini, P; Müller, H; Mundim, L M; Murray, W J; Muryn, B; Myatt, Gerald; Naraghi, F; Navarria, Francesco Luigi; Navas, S; Nawrocki, K; Negri, P; Neumann, W; Nicolaidou, R; Nielsen, B S; Nieuwenhuizen, M; Nikolaenko, V; Niss, P; Nomerotski, A; Normand, Ainsley; Novák, M; Oberschulte-Beckmann, W; Obraztsov, V F; Olshevskii, A G; Onofre, A; Orava, Risto; Österberg, K; Ouraou, A; Paganini, P; Paganoni, M; Pagès, P; Palka, H; Papadopoulou, T D; Papageorgiou, K; Pape, L; Parkes, C; Parodi, F; Passeri, A; Pegoraro, M; Peralta, L; Pernegger, H; Pernicka, Manfred; Perrotta, A; Petridou, C; Petrolini, A; Petrovykh, M; Phillips, H T; Piana, G; Pierre, F; Pimenta, M; Pindo, M; Plaszczynski, S; Podobrin, O; Pol, M E; Polok, G; Poropat, P; Pozdnyakov, V; Prest, M; Privitera, P; Pukhaeva, N; Pullia, Antonio; Radojicic, D; Ragazzi, S; Rahmani, H; Ratoff, P N; Read, A L; Reale, M; Rebecchi, P; Redaelli, N G; Regler, Meinhard; Reid, D; Renton, P B; Resvanis, L K; Richard, F; Richardson, J; Rídky, J; Rinaudo, G; Ripp, I; Romero, A; Roncagliolo, I; Ronchese, P; Ronjin, V M; Roos, L; Rosenberg, E I; Rosso, E; Roudeau, Patrick; Rovelli, T; Rückstuhl, W; Ruhlmann-Kleider, V; Ruiz, A; Rybicki, K; Saarikko, H; Sacquin, Yu; Sadovskii, A; Sajot, G; Salt, J; Sánchez, J; Sannino, M; Schimmelpfennig, M; Schneider, H; Schwickerath, U; Schyns, M A E; Sciolla, G; Scuri, F; Seager, P; Sedykh, Yu; Segar, A M; Seitz, A; Sekulin, R L; Shellard, R C; Siccama, I; Siegrist, P; Simonetti, S; Simonetto, F; Sissakian, A N; Sitár, B; Skaali, T B; Smadja, G; Smirnov, N; Smirnova, O G; Smith, G R; Solovyanov, O; Sosnowski, R; Souza-Santos, D; Spassoff, Tz; Spiriti, E; Sponholz, P; Squarcia, S; Stanescu, C; Stapnes, Steinar; Stavitski, I; Stichelbaut, F; Stocchi, A; Strauss, J; Strub, R; Stugu, B; Szczekowski, M; Szeptycka, M; Tabarelli de Fatis, T; Tavernet, J P; Chikilev, O G; Tilquin, A; Timmermans, J; Tkatchev, L G; Todorov, T; Toet, D Z; Tomaradze, A G; Tomé, B; Tonazzo, A; Tortora, L; Tranströmer, G; Treille, D; Trischuk, W; Tristram, G; Trombini, A; Troncon, C; Tsirou, A L; Turluer, M L; Tyapkin, I A; Tyndel, M; Tzamarias, S; Überschär, B; Ullaland, O; Uvarov, V; Valenti, G; Vallazza, E; Van der Velde, C; van Apeldoorn, G W; van Dam, P; Van Doninck, W K; Van Eldik, J; Vassilopoulos, N; Vegni, G; Ventura, L; Venus, W A; Verbeure, F; Verlato, M; Vertogradov, L S; Vilanova, D; Vincent, P; Vitale, L; Vlasov, E; Vodopyanov, A S; Vrba, V; Wahlen, H; Walck, C; Weierstall, M; Weilhammer, Peter; Weiser, C; Wetherell, Alan M; Wicke, D; Wickens, J H; Wielers, M; Wilkinson, G R; Williams, W S C; Winter, M; Witek, M; Woschnagg, K; Yip, K; Yushchenko, O P; Zach, F; Zaitsev, A; Zalewska-Bak, A; Zalewski, Piotr; Zavrtanik, D; Zevgolatakos, E; Zimin, N I; Zito, M; Zontar, D; Zuberi, R; Zucchelli, G C; Zumerle, G; Belokopytov, Yu; Charpentier, Ph; Gavillet, Ph; Gouz, Yu; Jarlskog, Ch; Khokhlov, Yu; Papadopoulou, Th D
1996-01-01
The measurement of the average lifetime of B hadrons using inclusively reconstructed secondary vertices has been updated using both an improved processing of previous data and additional statistics from new data. This has reduced the statistical and systematic uncertainties and gives \\tau_{\\mathrm{B}} = 1.582 \\pm 0.011\\ \\mathrm{(stat.)} \\pm 0.027\\ \\mathrm{(syst.)}\\ \\mathrm{ps.} Combining this result with the previous result based on charged particle impact parameter distributions yields \\tau_{\\mathrm{B}} = 1.575 \\pm 0.010\\ \\mathrm{(stat.)} \\pm 0.026\\ \\mathrm{(syst.)}\\ \\mathrm{ps.}
Laser properties of an improved average-power Nd-doped phosphate glass
International Nuclear Information System (INIS)
Payne, S.A.; Marshall, C.D.; Bayramian, A.J.
1995-01-01
The Nd-doped phosphate laser glass described herein can withstand 2.3 times greater thermal loading without fracture, compared to APG-1 (commercially-available average-power glass from Schott Glass Technologies). The enhanced thermal loading capability is established on the basis of the intrinsic thermomechanical properties (expansion, conduction, fracture toughness, and Young's modulus), and by direct thermally-induced fracture experiments using Ar-ion laser heating of the samples. This Nd-doped phosphate glass (referred to as APG-t) is found to be characterized by a 29% lower gain cross section and a 25% longer low-concentration emission lifetime
On the average configuration of the geomagnetic tail
International Nuclear Information System (INIS)
Fairfield, D.H.
1978-03-01
Over 3000 hours of IMP-6 magnetic field data obtained between 20 and 33 R sub E in the geomagnetic tail have been used in a statistical study of the tail configuration. A distribution of 2.5 minute averages of B sub Z as a function of position across the tail reveals that more flux crosses the equatorial plane near the dawn and dusk flanks than near midnight. The tail field projected in the solar magnetospheric equatorial plane deviates from the X axis due to flaring and solar wind aberration by an angle alpha = -0.9 y sub SM - 1.7, where y/sub SM/ is in earth radii and alpha is in degrees. After removing these effects the Y component of the tail field is found to depend on interplanetary sector structure. During an away sector the B/sub Y/ component of the tail field is on average 0.5 gamma greater than that during a toward sector, a result that is true in both tail lobes and is independent of location across the tail
Generalized Heteroskedasticity ACF for Moving Average Models in Explicit Forms
Directory of Open Access Journals (Sweden)
Samir Khaled Safi
2014-02-01
Full Text Available Normal 0 false false false MicrosoftInternetExplorer4 The autocorrelation function (ACF measures the correlation between observations at different distances apart. We derive explicit equations for generalized heteroskedasticity ACF for moving average of order q, MA(q. We consider two cases: Firstly: when the disturbance term follow the general covariance matrix structure Cov(wi, wj=S with si,j ¹ 0 " i¹j . Secondly: when the diagonal elements of S are not all identical but sij = 0 " i¹j, i.e. S=diag(s11, s22,…,stt. The forms of the explicit equations depend essentially on the moving average coefficients and covariance structure of the disturbance terms. /* Style Definitions */ table.MsoNormalTable {mso-style-name:"جدول عادي"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;}
Eighth CW and High Average Power RF Workshop
2014-01-01
We are pleased to announce the next Continuous Wave and High Average RF Power Workshop, CWRF2014, to take place at Hotel NH Trieste, Trieste, Italy from 13 to 16 May, 2014. This is the eighth in the CWRF workshop series and will be hosted by Elettra - Sincrotrone Trieste S.C.p.A. (www.elettra.eu). CWRF2014 will provide an opportunity for designers and users of CW and high average power RF systems to meet and interact in a convivial environment to share experiences and ideas on applications which utilize high-power klystrons, gridded tubes, combined solid-state architectures, high-voltage power supplies, high-voltage modulators, high-power combiners, circulators, cavities, power couplers and tuners. New ideas for high-power RF system upgrades and novel ways of RF power generation and distribution will also be discussed. CWRF2014 sessions will start on Tuesday morning and will conclude on Friday lunchtime. A visit to Elettra and FERMI will be organized during the workshop. ORGANIZING COMMITTEE (OC): Al...
Monthly streamflow forecasting with auto-regressive integrated moving average
Nasir, Najah; Samsudin, Ruhaidah; Shabri, Ani
2017-09-01
Forecasting of streamflow is one of the many ways that can contribute to better decision making for water resource management. The auto-regressive integrated moving average (ARIMA) model was selected in this research for monthly streamflow forecasting with enhancement made by pre-processing the data using singular spectrum analysis (SSA). This study also proposed an extension of the SSA technique to include a step where clustering was performed on the eigenvector pairs before reconstruction of the time series. The monthly streamflow data of Sungai Muda at Jeniang, Sungai Muda at Jambatan Syed Omar and Sungai Ketil at Kuala Pegang was gathered from the Department of Irrigation and Drainage Malaysia. A ratio of 9:1 was used to divide the data into training and testing sets. The ARIMA, SSA-ARIMA and Clustered SSA-ARIMA models were all developed in R software. Results from the proposed model are then compared to a conventional auto-regressive integrated moving average model using the root-mean-square error and mean absolute error values. It was found that the proposed model can outperform the conventional model.
Average gluon and quark jet multiplicities at higher orders
Energy Technology Data Exchange (ETDEWEB)
Bolzoni, Paolo; Kniehl, Bernd A. [Hamburg Univ. (Germany). 2. Inst. fuer Theoretische Physik; Kotikov, Anatoly V. [Hamburg Univ. (Germany). 2. Inst. fuer Theoretische Physik; Joint Institute of Nuclear Research, Moscow (Russian Federation). Bogoliubov Lab. of Theoretical Physics
2013-05-15
We develop a new formalism for computing and including both the perturbative and nonperturbative QCD contributions to the scale evolution of average gluon and quark jet multiplicities. The new method is motivated by recent progress in timelike small-x resummation obtained in the MS factorization scheme. We obtain next-to-next-to-leading-logarithmic (NNLL) resummed expressions, which represent generalizations of previous analytic results. Our expressions depend on two nonperturbative parameters with clear and simple physical interpretations. A global fit of these two quantities to all available experimental data sets that are compatible with regard to the jet algorithms demonstrates by its goodness how our results solve a longstanding problem of QCD. We show that the statistical and theoretical uncertainties both do not exceed 5% for scales above 10 GeV. We finally propose to use the jet multiplicity data as a new way to extract the strong-coupling constant. Including all the available theoretical input within our approach, we obtain {alpha}{sub s}{sup (5)}(M{sub Z})=0.1199{+-}0.0026 in the MS scheme in an approximation equivalent to next-to-next-to-leading order enhanced by the resummations of ln(x) terms through the NNLL level and of ln Q{sup 2} terms by the renormalization group, in excellent agreement with the present world average.
Macroeconomic Forecasts in Models with Bayesian Averaging of Classical Estimates
Directory of Open Access Journals (Sweden)
Piotr Białowolski
2012-03-01
Full Text Available The aim of this paper is to construct a forecasting model oriented on predicting basic macroeconomic variables, namely: the GDP growth rate, the unemployment rate, and the consumer price inflation. In order to select the set of the best regressors, Bayesian Averaging of Classical Estimators (BACE is employed. The models are atheoretical (i.e. they do not reflect causal relationships postulated by the macroeconomic theory and the role of regressors is played by business and consumer tendency survey-based indicators. Additionally, survey-based indicators are included with a lag that enables to forecast the variables of interest (GDP, unemployment, and inflation for the four forthcoming quarters without the need to make any additional assumptions concerning the values of predictor variables in the forecast period. Bayesian Averaging of Classical Estimators is a method allowing for full and controlled overview of all econometric models which can be obtained out of a particular set of regressors. In this paper authors describe the method of generating a family of econometric models and the procedure for selection of a final forecasting model. Verification of the procedure is performed by means of out-of-sample forecasts of main economic variables for the quarters of 2011. The accuracy of the forecasts implies that there is still a need to search for new solutions in the atheoretical modelling.
The partially averaged field approach to cosmic ray diffusion
International Nuclear Information System (INIS)
Jones, F.C.; Birmingham, T.J.; Kaiser, T.B.
1976-08-01
The kinetic equation for particles interacting with turbulent fluctuations is derived by a new nonlinear technique which successfully corrects the difficulties associated with quasilinear theory. In this new method the effects of the fluctuations are evaluated along particle orbits which themselves include the effects of a statistically averaged subset of the possible configurations of the turbulence. The new method is illustrated by calculating the pitch angle diffusion coefficient D/sub Mu Mu/ for particles interacting with slab-model magnetic turbulence, i.e., magnetic fluctuations linearly polarized transverse to a mean magnetic field. Results are compared with those of quasilinear theory and also with those of Monte Carlo calculations. The major effect of the nonlinear treatment in this illustration is the determination of D/sub Mu Mu/ in the vicinity of 90 deg pitch angles where quasilinear theory breaks down. The spatial diffusion coefficient parallel to a mean magnetic field is evaluated using D/sub Mu Mu/ as calculated by this technique. It is argued that the partially averaged field method is not limited to small amplitude fluctuating fields, and is, hence, not a perturbation theory
Image compression using moving average histogram and RBF network
International Nuclear Information System (INIS)
Khowaja, S.; Ismaili, I.A.
2015-01-01
Modernization and Globalization have made the multimedia technology as one of the fastest growing field in recent times but optimal use of bandwidth and storage has been one of the topics which attract the research community to work on. Considering that images have a lion share in multimedia communication, efficient image compression technique has become the basic need for optimal use of bandwidth and space. This paper proposes a novel method for image compression based on fusion of moving average histogram and RBF (Radial Basis Function). Proposed technique employs the concept of reducing color intensity levels using moving average histogram technique followed by the correction of color intensity levels using RBF networks at reconstruction phase. Existing methods have used low resolution images for the testing purpose but the proposed method has been tested on various image resolutions to have a clear assessment of the said technique. The proposed method have been tested on 35 images with varying resolution and have been compared with the existing algorithms in terms of CR (Compression Ratio), MSE (Mean Square Error), PSNR (Peak Signal to Noise Ratio), computational complexity. The outcome shows that the proposed methodology is a better trade off technique in terms of compression ratio, PSNR which determines the quality of the image and computational complexity. (author)
Large interface simulation in an averaged two-fluid code
International Nuclear Information System (INIS)
Henriques, A.
2006-01-01
Different ranges of size of interfaces and eddies are involved in multiphase flow phenomena. Classical formalisms focus on a specific range of size. This study presents a Large Interface Simulation (LIS) two-fluid compressible formalism taking into account different sizes of interfaces. As in the single-phase Large Eddy Simulation, a filtering process is used to point out Large Interface (LI) simulation and Small interface (SI) modelization. The LI surface tension force is modelled adapting the well-known CSF method. The modelling of SI transfer terms is done calling for classical closure laws of the averaged approach. To simulate accurately LI transfer terms, we develop a LI recognition algorithm based on a dimensionless criterion. The LIS model is applied in a classical averaged two-fluid code. The LI transfer terms modelling and the LI recognition are validated on analytical and experimental tests. A square base basin excited by a horizontal periodic movement is studied with the LIS model. The capability of the model is also shown on the case of the break-up of a bubble in a turbulent liquid flow. The break-up of a large bubble at a grid impact performed regime transition between two different scales of interface from LI to SI and from PI to LI. (author) [fr
Average cross sections calculated in various neutron fields
International Nuclear Information System (INIS)
Shibata, Keiichi
2002-01-01
Average cross sections have been calculated for the reactions contained in the dosimetry files, JENDL/D-99, IRDF-90V2, and RRDF-98 in order to select the best data for the new library IRDF-2002. The neutron spectra used in the calculations are as follows: 1) 252 Cf spontaneous fission spectrum (NBS evaluation), 2) 235 U thermal fission spectrum (NBS evaluation), 3) Intermediate-energy Standard Neutron Field (ISNF), 4) Coupled Fast Reactivity Measurement Facility (CFRMF), 5) Coupled thermal/fast uranium and boron carbide spherical assembly (ΣΣ), 6) Fast neutron source reactor (YAYOI), 7) Experimental fast reactor (JOYO), 8) Japan Material Testing Reactor (JMTR), 9) d-Li neutron spectrum with a 2-MeV deuteron beam. The items 3)-7) represent fast neutron spectra, while JMTR is a light water reactor. The Q-value for the d-Li reaction mentioned above is 15.02 MeV. Therefore, neutrons with energies up to 17 MeV can be produced in the d-Li reaction. The calculated average cross sections were compared with the measurements. Figures 1-9 show the ratios of the calculations to the experimental data which are given. It is found from these figures that the 58 Fe(n, γ) cross section in JENDL/D-99 reproduces the measurements in the thermal and fast reactor spectra better than that in IRDF-90V2. (author)
Prompt fission neutron spectra and average prompt neutron multiplicities
International Nuclear Information System (INIS)
Madland, D.G.; Nix, J.R.
1983-01-01
We present a new method for calculating the prompt fission neutron spectrum N(E) and average prompt neutron multiplicity anti nu/sub p/ as functions of the fissioning nucleus and its excitation energy. The method is based on standard nuclear evaporation theory and takes into account (1) the motion of the fission fragments, (2) the distribution of fission-fragment residual nuclear temperature, (3) the energy dependence of the cross section sigma/sub c/ for the inverse process of compound-nucleus formation, and (4) the possibility of multiple-chance fission. We use a triangular distribution in residual nuclear temperature based on the Fermi-gas model. This leads to closed expressions for N(E) and anti nu/sub p/ when sigma/sub c/ is assumed constant and readily computed quadratures when the energy dependence of sigma/sub c/ is determined from an optical model. Neutron spectra and average multiplicities calculated with an energy-dependent cross section agree well with experimental data for the neutron-induced fission of 235 U and the spontaneous fission of 252 Cf. For the latter case, there are some significant inconsistencies between the experimental spectra that need to be resolved. 29 references
The average crossing number of equilateral random polygons
International Nuclear Information System (INIS)
Diao, Y; Dobay, A; Kusner, R B; Millett, K; Stasiak, A
2003-01-01
In this paper, we study the average crossing number of equilateral random walks and polygons. We show that the mean average crossing number ACN of all equilateral random walks of length n is of the form (3/16)n ln n + O(n). A similar result holds for equilateral random polygons. These results are confirmed by our numerical studies. Furthermore, our numerical studies indicate that when random polygons of length n are divided into individual knot types, the for each knot type K can be described by a function of the form = a(n-n 0 )ln(n-n 0 ) + b(n-n 0 ) + c where a, b and c are constants depending on K and n 0 is the minimal number of segments required to form K. The profiles diverge from each other, with more complex knots showing higher than less complex knots. Moreover, the profiles intersect with the profile of all closed walks. These points of intersection define the equilibrium length of K, i.e., the chain length n e (K) at which a statistical ensemble of configurations with given knot type K-upon cutting, equilibration and reclosure to a new knot type K'-does not show a tendency to increase or decrease . This concept of equilibrium length seems to be universal, and applies also to other length-dependent observables for random knots, such as the mean radius of gyration g >
Vibrationally averaged dipole moments of methane and benzene isotopologues
Energy Technology Data Exchange (ETDEWEB)
Arapiraca, A. F. C. [Laboratório de Átomos e Moléculas Especiais, Departamento de Física, ICEx, Universidade Federal de Minas Gerais, P. O. Box 702, 30123-970 Belo Horizonte, MG (Brazil); Centro Federal de Educação Tecnológica de Minas Gerais, Coordenação de Ciências, CEFET-MG, Campus I, 30.421-169 Belo Horizonte, MG (Brazil); Mohallem, J. R., E-mail: rachid@fisica.ufmg.br [Laboratório de Átomos e Moléculas Especiais, Departamento de Física, ICEx, Universidade Federal de Minas Gerais, P. O. Box 702, 30123-970 Belo Horizonte, MG (Brazil)
2016-04-14
DFT-B3LYP post-Born-Oppenheimer (finite-nuclear-mass-correction (FNMC)) calculations of vibrationally averaged isotopic dipole moments of methane and benzene, which compare well with experimental values, are reported. For methane, in addition to the principal vibrational contribution to the molecular asymmetry, FNMC accounts for the surprisingly large Born-Oppenheimer error of about 34% to the dipole moments. This unexpected result is explained in terms of concurrent electronic and vibrational contributions. The calculated dipole moment of C{sub 6}H{sub 3}D{sub 3} is about twice as large as the measured dipole moment of C{sub 6}H{sub 5}D. Computational progress is advanced concerning applications to larger systems and the choice of appropriate basis sets. The simpler procedure of performing vibrational averaging on the Born-Oppenheimer level and then adding the FNMC contribution evaluated at the equilibrium distance is shown to be appropriate. Also, the basis set choice is made by heuristic analysis of the physical behavior of the systems, instead of by comparison with experiments.
Face averages enhance user recognition for smartphone security.
Robertson, David J; Kramer, Robin S S; Burton, A Mike
2015-01-01
Our recognition of familiar faces is excellent, and generalises across viewing conditions. However, unfamiliar face recognition is much poorer. For this reason, automatic face recognition systems might benefit from incorporating the advantages of familiarity. Here we put this to the test using the face verification system available on a popular smartphone (the Samsung Galaxy). In two experiments we tested the recognition performance of the smartphone when it was encoded with an individual's 'face-average'--a representation derived from theories of human face perception. This technique significantly improved performance for both unconstrained celebrity images (Experiment 1) and for real faces (Experiment 2): users could unlock their phones more reliably when the device stored an average of the user's face than when they stored a single image. This advantage was consistent across a wide variety of everyday viewing conditions. Furthermore, the benefit did not reduce the rejection of imposter faces. This benefit is brought about solely by consideration of suitable representations for automatic face recognition, and we argue that this is just as important as development of matching algorithms themselves. We propose that this representation could significantly improve recognition rates in everyday settings.
Determination of the average lifetime of b-baryons
International Nuclear Information System (INIS)
Abreu, P.; Adam, W.
1996-01-01
The average lifetime of b-baryons has been studied using 3.10 6 hadronic Z 0 decays collected by the DELPHI detector at LEP. Three methods have been used, based on the measurement of different observables: the proper decay time distribution of 206 vertices reconstructed with a Λ, a lepton and an oppositely charged pion; the impact parameter distribution of 441 muons with high transverse momentum accompanied by a Λ in the same jet; and the proper decay time distribution of 125 Λ c -lepton decay vertices with the Λ c exclusively reconstructed through its pKπ, pK 0 and Λ3π decay modes. The combined result is: τ(b-baryon)=(1.254 +0.121 -0.109 (stat) ±0.04(syst) +0.03 -0.05 (syst)) ps where the first systematic error is due to experimental uncertainties and the second to the uncertainties in the modelling of the b-baryon production and semi-leptonic decay. Including the measurement recently published by DELPHI based on a sample of proton-muon vertices, the average b-baryon lifetime is: τ(b-baryon)=(1.255 +0.115 -0.102 (stat) ±0.05) ps. (orig.)
Using Bayes Model Averaging for Wind Power Forecasts
Preede Revheim, Pål; Beyer, Hans Georg
2014-05-01
For operational purposes predictions of the forecasts of the lumped output of groups of wind farms spread over larger geographic areas will often be of interest. A naive approach is to make forecasts for each individual site and sum them up to get the group forecast. It is however well documented that a better choice is to use a model that also takes advantage of spatial smoothing effects. It might however be the case that some sites tends to more accurately reflect the total output of the region, either in general or for certain wind directions. It will then be of interest giving these a greater influence over the group forecast. Bayesian model averaging (BMA) is a statistical post-processing method for producing probabilistic forecasts from ensembles. Raftery et al. [1] show how BMA can be used for statistical post processing of forecast ensembles, producing PDFs of future weather quantities. The BMA predictive PDF of a future weather quantity is a weighted average of the ensemble members' PDFs, where the weights can be interpreted as posterior probabilities and reflect the ensemble members' contribution to overall forecasting skill over a training period. In Revheim and Beyer [2] the BMA procedure used in Sloughter, Gneiting and Raftery [3] were found to produce fairly accurate PDFs for the future mean wind speed of a group of sites from the single sites wind speeds. However, when the procedure was attempted applied to wind power it resulted in either problems with the estimation of the parameters (mainly caused by longer consecutive periods of no power production) or severe underestimation (mainly caused by problems with reflecting the power curve). In this paper the problems that arose when applying BMA to wind power forecasting is met through two strategies. First, the BMA procedure is run with a combination of single site wind speeds and single site wind power production as input. This solves the problem with longer consecutive periods where the input data
A Tidally Averaged Sediment-Transport Model for San Francisco Bay, California
Lionberger, Megan A.; Schoellhamer, David H.
2009-01-01
A tidally averaged sediment-transport model of San Francisco Bay was incorporated into a tidally averaged salinity box model previously developed and calibrated using salinity, a conservative tracer (Uncles and Peterson, 1995; Knowles, 1996). The Bay is represented in the model by 50 segments composed of two layers: one representing the channel (>5-meter depth) and the other the shallows (0- to 5-meter depth). Calculations are made using a daily time step and simulations can be made on the decadal time scale. The sediment-transport model includes an erosion-deposition algorithm, a bed-sediment algorithm, and sediment boundary conditions. Erosion and deposition of bed sediments are calculated explicitly, and suspended sediment is transported by implicitly solving the advection-dispersion equation. The bed-sediment model simulates the increase in bed strength with depth, owing to consolidation of fine sediments that make up San Francisco Bay mud. The model is calibrated to either net sedimentation calculated from bathymetric-change data or measured suspended-sediment concentration. Specified boundary conditions are the tributary fluxes of suspended sediment and suspended-sediment concentration in the Pacific Ocean. Results of model calibration and validation show that the model simulates the trends in suspended-sediment concentration associated with tidal fluctuations, residual velocity, and wind stress well, although the spring neap tidal suspended-sediment concentration variability was consistently underestimated. Model validation also showed poor simulation of seasonal sediment pulses from the Sacramento-San Joaquin River Delta at Point San Pablo because the pulses enter the Bay over only a few days and the fate of the pulses is determined by intra-tidal deposition and resuspension that are not included in this tidally averaged model. The model was calibrated to net-basin sedimentation to calculate budgets of sediment and sediment-associated contaminants. While
Southwick, Lloyd M; Appelboom, Timothy W; Fouss, James L
2009-02-25
The movement of the herbicide metolachlor [2-chloro-N-(2-ethyl-6-methylphenyl)-N-(2-methoxy-1-methylethyl)acetamide] via runoff and leaching from 0.21 ha plots planted to corn on Mississippi River alluvial soil (Commerce silt loam) was measured for a 6-year period, 1995-2000. The first three years received normal rainfall (30 year average); the second three years experienced reduced rainfall. The 4-month periods prior to application plus the following 4 months after application were characterized by 1039 +/- 148 mm of rainfall for 1995-1997 and by 674 +/- 108 mm for 1998-2000. During the normal rainfall years 216 +/- 150 mm of runoff occurred during the study seasons (4 months following herbicide application), accompanied by 76.9 +/- 38.9 mm of leachate. For the low-rainfall years these amounts were 16.2 +/- 18.2 mm of runoff (92% less than the normal years) and 45.1 +/- 25.5 mm of leachate (41% less than the normal seasons). Runoff of metolachlor during the normal-rainfall seasons was 4.5-6.1% of application, whereas leaching was 0.10-0.18%. For the below-normal periods, these losses were 0.07-0.37% of application in runoff and 0.22-0.27% in leachate. When averages over the three normal and the three less-than-normal seasons were taken, a 35% reduction in rainfall was characterized by a 97% reduction in runoff loss and a 71% increase in leachate loss of metolachlor on a percent of application basis. The data indicate an increase in preferential flow in the leaching movement of metolachlor from the surface soil layer during the reduced rainfall periods. Even with increased preferential flow through the soil during the below-average rainfall seasons, leachate loss (percent of application) of the herbicide remained below 0.3%. Compared to the average rainfall seasons of 1995-1997, the below-normal seasons of 1998-2000 were characterized by a 79% reduction in total runoff and leachate flow and by a 93% reduction in corresponding metolachlor movement via these routes
Indoor radon concentration in Poland
International Nuclear Information System (INIS)
Mamont-Ciesla, K.; Jagielak, J.; Rosinski, S.W.; Sosinka, A.; Bysiek, M.; Henschke, J.
1996-01-01
Preliminary survey of Rn concentration indoors by means of track detectors and y-ray dose rate with the use of TLD in almost 500 homes in selected areas of Poland was performed in the late 1980s. It was concluded that radon contributes 1.16 mSv i.e. about 46 per cent of the total natural environment ionizing radiation dose to the Polish population. Comparison of the average radon concentrations in 4 seasons of a year and in 3 groups of buildings: masonry, concrete and wood, revealed that the ground beneath the building structure is likely the dominant source of radon indoors. Since the National Atomic Energy Agency in its regulations of 1988-03-31 set up the permissible limit of the equilibrium equivalent concentration of radon in new buildings (equal 100 Bq/m3), the nation-scale survey project for radon in buildings has been undertaken. These regulations were supposed to take effect in 1995-01-01. The project has 3 objectives: to estimate the radiation exposure due to radon daughters received by Polish population to identify radon-prone areas in Poland to investigate dependence of the indoor radon concentrations on such parameters as: type of construction material, presence (or absence) of cellar under the building, number of floor
Modeling and Forecasting Average Temperature for Weather Derivative Pricing
Directory of Open Access Journals (Sweden)
Zhiliang Wang
2015-01-01
Full Text Available The main purpose of this paper is to present a feasible model for the daily average temperature on the area of Zhengzhou and apply it to weather derivatives pricing. We start by exploring the background of weather derivatives market and then use the 62 years of daily historical data to apply the mean-reverting Ornstein-Uhlenbeck process to describe the evolution of the temperature. Finally, Monte Carlo simulations are used to price heating degree day (HDD call option for this city, and the slow convergence of the price of the HDD call can be found through taking 100,000 simulations. The methods of the research will provide a frame work for modeling temperature and pricing weather derivatives in other similar places in China.
Data Point Averaging for Computational Fluid Dynamics Data
Norman, Jr., David (Inventor)
2016-01-01
A system and method for generating fluid flow parameter data for use in aerodynamic heating analysis. Computational fluid dynamics data is generated for a number of points in an area on a surface to be analyzed. Sub-areas corresponding to areas of the surface for which an aerodynamic heating analysis is to be performed are identified. A computer system automatically determines a sub-set of the number of points corresponding to each of the number of sub-areas and determines a value for each of the number of sub-areas using the data for the sub-set of points corresponding to each of the number of sub-areas. The value is determined as an average of the data for the sub-set of points corresponding to each of the number of sub-areas. The resulting parameter values then may be used to perform an aerodynamic heating analysis.
Averaged multivalued solutions and time discretization for conservation laws
International Nuclear Information System (INIS)
Brenier, Y.
1985-01-01
It is noted that the correct shock solutions can be approximated by averaging in some sense the multivalued solution given by the method of characteristics for the nonlinear scalar conservation law (NSCL). A time discretization for the NSCL equation based on this principle is considered. An equivalent analytical formulation is shown to lead quite easily to a convergence result, and a third formulation is introduced which can be generalized for the systems of conservation laws. Various numerical schemes are constructed from the proposed time discretization. The first family of schemes is obtained by using a spatial grid and projecting the results of the time discretization. Many known schemes are then recognized (mainly schemes by Osher, Roe, and LeVeque). A second way to discretize leads to a particle scheme without space grid, which is very efficient (at least in the scalar case). Finally, a close relationship between the proposed method and the Boltzmann type schemes is established. 14 references
Extracting Credible Dependencies for Averaged One-Dependence Estimator Analysis
Directory of Open Access Journals (Sweden)
LiMin Wang
2014-01-01
Full Text Available Of the numerous proposals to improve the accuracy of naive Bayes (NB by weakening the conditional independence assumption, averaged one-dependence estimator (AODE demonstrates remarkable zero-one loss performance. However, indiscriminate superparent attributes will bring both considerable computational cost and negative effect on classification accuracy. In this paper, to extract the most credible dependencies we present a new type of seminaive Bayesian operation, which selects superparent attributes by building maximum weighted spanning tree and removes highly correlated children attributes by functional dependency and canonical cover analysis. Our extensive experimental comparison on UCI data sets shows that this operation efficiently identifies possible superparent attributes at training time and eliminates redundant children attributes at classification time.
Ocean tides in GRACE monthly averaged gravity fields
DEFF Research Database (Denmark)
Knudsen, Per
2003-01-01
The GRACE mission will map the Earth's gravity fields and its variations with unprecedented accuracy during its 5-year lifetime. Unless ocean tide signals and their load upon the solid earth are removed from the GRACE data, their long period aliases obscure more subtle climate signals which GRACE...... aims at. In this analysis the results of Knudsen and Andersen (2002) have been verified using actual post-launch orbit parameter of the GRACE mission. The current ocean tide models are not accurate enough to correct GRACE data at harmonic degrees lower than 47. The accumulated tidal errors may affect...... the GRACE data up to harmonic degree 60. A study of the revised alias frequencies confirm that the ocean tide errors will not cancel in the GRACE monthly averaged temporal gravity fields. The S-2 and the K-2 terms have alias frequencies much longer than 30 days, so they remain almost unreduced...
Quantitative metagenomic analyses based on average genome size normalization
DEFF Research Database (Denmark)
Frank, Jeremy Alexander; Sørensen, Søren Johannes
2011-01-01
provide not just a census of the community members but direct information on metabolic capabilities and potential interactions among community members. Here we introduce a method for the quantitative characterization and comparison of microbial communities based on the normalization of metagenomic data...... marine sources using both conventional small-subunit (SSU) rRNA gene analyses and our quantitative method to calculate the proportion of genomes in each sample that are capable of a particular metabolic trait. With both environments, to determine what proportion of each community they make up and how......). These analyses demonstrate how genome proportionality compares to SSU rRNA gene relative abundance and how factors such as average genome size and SSU rRNA gene copy number affect sampling probability and therefore both types of community analysis....
Mean link versus average plaquette tadpoles in lattice NRQCD
Shakespeare, Norman H.; Trottier, Howard D.
1999-03-01
We compare mean-link and average plaquette tadpole renormalization schemes in the context of the quarkonium hyperfine splittings in lattice NRQCD. Simulations are done for the three quarkonium systems c overlinec, b overlinec, and b overlineb. The hyperfine splittings are computed both at leading and at next-to-leading order in the relativistic expansion. Results are obtained at a large number of lattice spacings. A number of features emerge, all of which favor tadpole renormalization using mean links. This includes much better scaling of the hyperfine splittings in the three quarkonium systems. We also find that relativistic corrections to the spin splittings are smaller with mean-link tadpoles, particularly for the c overlinec and b overlinec systems. We also see signs of a breakdown in the NRQCD expansion when the bare quark mass falls below about one in lattice units (with the bare quark masses turning out to be much larger with mean-link tadpoles).
An Exponentially Weighted Moving Average Control Chart for Bernoulli Data
DEFF Research Database (Denmark)
Spliid, Henrik
2010-01-01
of the transformation is given and its limit for small values of p is derived. Control of high yield processes is discussed and the chart is shown to perform very well in comparison with both the most common alternative EWMA chart and the CUSUM chart. The construction and the use of the proposed EWMA chart......We consider a production process in which units are produced in a sequential manner. The units can, for example, be manufactured items or services, provided to clients. Each unit produced can be a failure with probability p or a success (non-failure) with probability (1-p). A novel exponentially...... weighted moving average (EWMA) control chart intended for surveillance of the probability of failure, p, is described. The chart is based on counting the number of non-failures produced between failures in combination with a variance-stabilizing transformation. The distribution function...
Voter dynamics on an adaptive network with finite average connectivity
Mukhopadhyay, Abhishek; Schmittmann, Beate
2009-03-01
We study a simple model for voter dynamics in a two-party system. The opinion formation process is implemented in a random network of agents in which interactions are not restricted by geographical distance. In addition, we incorporate the rapidly changing nature of the interpersonal relations in the model. At each time step, agents can update their relationships, so that there is no history dependence in the model. This update is determined by their own opinion, and by their preference to make connections with individuals sharing the same opinion and with opponents. Using simulations and analytic arguments, we determine the final steady states and the relaxation into these states for different system sizes. In contrast to earlier studies, the average connectivity (``degree'') of each agent is constant here, independent of the system size. This has significant consequences for the long-time behavior of the model.
High-average-power laser medium based on silica glass
Fujimoto, Yasushi; Nakatsuka, Masahiro
2000-01-01
Silica glass is one of the most attractive materials for a high-average-power laser. We have developed a new laser material base don silica glass with zeolite method which is effective for uniform dispersion of rare earth ions in silica glass. High quality medium, which is bubbleless and quite low refractive index distortion, must be required for realization of laser action. As the main reason of bubbling is due to hydroxy species remained in the gelation same, we carefully choose colloidal silica particles, pH value of hydrochloric acid for hydrolysis of tetraethylorthosilicate on sol-gel process, and temperature and atmosphere control during sintering process, and then we get a bubble less transparent rare earth doped silica glass. The refractive index distortion of the sample also discussed.
Averaging scheme for atomic resolution off-axis electron holograms.
Niermann, T; Lehmann, M
2014-08-01
All micrographs are limited by shot-noise, which is intrinsic to the detection process of electrons. For beam insensitive specimen this limitation can in principle easily be circumvented by prolonged exposure times. However, in the high-resolution regime several instrumental instabilities limit the applicable exposure time. Particularly in the case of off-axis holography the holograms are highly sensitive to the position and voltage of the electron-optical biprism. We present a novel reconstruction algorithm to average series of off-axis holograms while compensating for specimen drift, biprism drift, drift of biprism voltage, and drift of defocus, which all might cause problematic changes from exposure to exposure. We show an application of the algorithm utilizing also the possibilities of double biprism holography, which results in a high quality exit-wave reconstruction with 75 pm resolution at a very high signal-to-noise ratio. Copyright © 2014 Elsevier Ltd. All rights reserved.
A note on computing average state occupation times
Directory of Open Access Journals (Sweden)
Jan Beyersmann
2014-05-01
Full Text Available Objective: This review discusses how biometricians would probably compute or estimate expected waiting times, if they had the data. Methods: Our framework is a time-inhomogeneous Markov multistate model, where all transition hazards are allowed to be time-varying. We assume that the cumulative transition hazards are given. That is, they are either known, as in a simulation, determined by expert guesses, or obtained via some method of statistical estimation. Our basic tool is product integration, which transforms the transition hazards into the matrix of transition probabilities. Product integration enjoys a rich mathematical theory, which has successfully been used to study probabilistic and statistical aspects of multistate models. Our emphasis will be on practical implementation of product integration, which allows us to numerically approximate the transition probabilities. Average state occupation times and other quantities of interest may then be derived from the transition probabilities.
Recent developments in high average power driver technology
International Nuclear Information System (INIS)
Prestwich, K.R.; Buttram, M.T.; Rohwein, G.J.
1979-01-01
Inertial confinement fusion (ICF) reactors will require driver systems operating with tens to hundreds of megawatts of average power. The pulse power technology that will be required to build such drivers is in a primitive state of development. Recent developments in repetitive pulse power are discussed. A high-voltage transformer has been developed and operated at 3 MV in a single pulse experiment and is being tested at 1.5 MV, 5 kj and 10 pps. A low-loss, 1 MV, 10 kj, 10 pps Marx generator is being tested. Test results from gas-dynamic spark gaps that operate both in the 100 kV and 700 kV range are reported. A 250 kV, 1.5 kA/cm 2 , 30 ns electron beam diode has operated stably for 1.6 x 10 5 pulses
A Note on Functional Averages over Gaussian Ensembles
Directory of Open Access Journals (Sweden)
Gabriel H. Tucci
2013-01-01
Full Text Available We find a new formula for matrix averages over the Gaussian ensemble. Let H be an n×n Gaussian random matrix with complex, independent, and identically distributed entries of zero mean and unit variance. Given an n×n positive definite matrix A and a continuous function f:ℝ+→ℝ such that ∫0∞e-αt|f(t|2dt0, we find a new formula for the expectation [Tr(f(HAH*]. Taking f(x=log(1+x gives another formula for the capacity of the MIMO communication channel, and taking f(x=(1+x-1 gives the MMSE achieved by a linear receiver.
Average properties of cosmic ray diffusion in solar wind streams
International Nuclear Information System (INIS)
Morfill, G.; Richter, A.K.; Scholer, M.
1979-01-01
Applying a superposed epoch analysis to the Mariner 5 plasma and magnetic field observations of 13 corotating high speed solar wind streams, we obtain the average azimuthal distribution of all relevant parameters of the background interplanetary medium, as well as those of superimposed Alfven waves. Using these measurements in model calculations allows us to determine the radial and azimuthal variation of the background and fluctuation parameters between 1 and 5 AU, and thus to calculate the cosmic ray diffusion coefficient kappa from the plasma and field properties. The calculation of kappa assumes that quasi-linear wave-particle interaction theory is applicable, and that the Alfven waves responsible for the scattering are propagating in the azimuthally varying solar wind according to geometrical optics. The consequences of these calculations regarding the occurrence of solar wind stream associated Forbush decreases are discussed
Quantum gravity unification via transfinite arithmetic and geometrical averaging
International Nuclear Information System (INIS)
El Naschie, M.S.
2008-01-01
In E-Infinity theory, we have not only infinitely many dimensions but also infinitely many fundamental forces. However, due to the hierarchical structure of ε (∞) spacetime we have a finite expectation number for its dimensionality and likewise a finite expectation number for the corresponding interactions. Starting from the preceding fundamental principles and using the experimental findings as well as the theoretical value of the coupling constants of the electroweak and the strong forces we present an extremely simple averaging procedure for determining the quantum gravity unification coupling constant with and without super symmetry. The work draws heavily on previous results, in particular a paper, by the Slovian Prof. Marek-Crnjac [Marek-Crnjac L. On the unification of all fundamental forces in a fundamentally fuzzy Cantorian ε (∞) manifold and high energy physics. Chaos, Solitons and Fractals 2004;4:657-68
Applications of ordered weighted averaging (OWA operators in environmental problems
Directory of Open Access Journals (Sweden)
Carlos Llopis-Albert
2017-04-01
Full Text Available This paper presents an application of a prioritized weighted aggregation operator based on ordered weighted averaging (OWA to deal with stakeholders' constructive participation in water resources projects. They have different degree of acceptance or preference regarding the measures and policies to be carried out, which lead to different environmental and socio-economic outcomes, and hence, to different levels of stakeholders’ satisfaction. The methodology establishes a prioritization relationship upon the stakeholders, which preferences are aggregated by means of weights depending on the satisfaction of the higher priority policy maker. The methodology establishes a prioritization relationship upon the stakeholders, which preferences are aggregated by means of weights depending on the satisfaction of the higher priority policy maker. The methodology has been successfully applied to a Public Participation Project (PPP in watershed management, thus obtaining efficient environmental measures in conflict resolution problems under actors’ preference uncertainties.
Zonally averaged chemical-dynamical model of the lower thermosphere
International Nuclear Information System (INIS)
Kasting, J.F.; Roble, R.G.
1981-01-01
A zonally averaged numerical model of the thermosphere is used to examine the coupling between neutral composition, including N 2 , O 2 and O, temperature, and winds at solstice for solar minimum conditions. The meridional circulation forced by solar heating results in a summer-to-winter flow, with a winter enhancement in atomic oxygen density that is a factor of about 1.8 greater than the summer hemisphere at 160 km. The O 2 and N 2 variations are associated with a latitudinal gradient in total number density, which is required to achieve pressure balance in the presence of large zonal jets. Latitudinal profiles OI (5577A) green line emission intensity are calculated by using both Chapman and Barth mechanisms. Composition of the lower thermosphere is shown to be strongly influenced by circulation patterns initiated in the stratosphere and lower mesosphere, below the lower boundary used in the model
Average size of random polygons with fixed knot topology.
Matsuda, Hiroshi; Yao, Akihisa; Tsukahara, Hiroshi; Deguchi, Tetsuo; Furuta, Ko; Inami, Takeo
2003-07-01
We have evaluated by numerical simulation the average size R(K) of random polygons of fixed knot topology K=,3(1),3(1) musical sharp 4(1), and we have confirmed the scaling law R(2)(K) approximately N(2nu(K)) for the number N of polygonal nodes in a wide range; N=100-2200. The best fit gives 2nu(K) approximately 1.11-1.16 with good fitting curves in the whole range of N. The estimate of 2nu(K) is consistent with the exponent of self-avoiding polygons. In a limited range of N (N greater, similar 600), however, we have another fit with 2nu(K) approximately 1.01-1.07, which is close to the exponent of random polygons.
Estimating the average grain size of metals - approved standard 1969
International Nuclear Information System (INIS)
Anon.
1975-01-01
These methods cover procedures for estimating and rules for expressing the average grain size of all metals and consisting entirely, or principally, of a single phase. The methods may also be used for any structures having appearances similar to those of the metallic structures shown in the comparison charts. The three basic procedures for grain size estimation which are discussed are comparison procedure, intercept (or Heyn) procedure, and planimetric (or Jeffries) procedure. For specimens consisting of equiaxed grains, the method of comparing the specimen with a standard chart is most convenient and is sufficiently accurate for most commercial purposes. For high degrees of accuracy in estimating grain size, the intercept or planimetric procedures may be used
Suicide attempts, platelet monoamine oxidase and the average evoked response
International Nuclear Information System (INIS)
Buchsbaum, M.S.; Haier, R.J.; Murphy, D.L.
1977-01-01
The relationship between suicides and suicide attempts and two biological measures, platelet monoamine oxidase levels (MAO) and average evoked response (AER) augmenting was examined in 79 off-medication psychiatric patients and in 68 college student volunteers chosen from the upper and lower deciles of MAO activity levels. In the patient sample, male individuals with low MAO and AER augmenting, a pattern previously associated with bipolar affective disorders, showed a significantly increased incidence of suicide attempts in comparison with either non-augmenting low MAO or high MAO patients. Within the normal volunteer group, all male low MAO probands with a family history of suicide or suicide attempts were AER augmenters themselves. Four completed suicides were found among relatives of low MAO probands whereas no high MAO proband had a relative who committed suicide. These findings suggest that the combination of low platelet MAO activity and AER augmenting may be associated with a possible genetic vulnerability to psychiatric disorders. (author)
Analysis of average radiation widths of neutron resonances
International Nuclear Information System (INIS)
Malezki, H.; Popov, A.B.; Trzeciak, K.
1982-01-01
On the basis of the available data on parameters of neutron resonances average values of radiation widths (GITAsub(γ)) are calculated for a wide range of nuclei in the 50 upto 250 atomic weight range. Experimental values are compared with different variants of theoretical estimates of GITAsub(γ) which are reduced to the GITAsub(γ) dependence upon atomic weight A, excitation energy U and level density parameter a as GITAsub(γ)=CAsup(α)Usup(β)asup(γ). Besides, empirical values C, α, β, γ are selected satisfying the experimental data best of all. It is determined that the use of a=kA hypothesis leads to a sufficiently better agreement between all theoretical estimates of GITAsub(γ) and experimental values. It turned out that the estimations by Weisskopf, Bondarenko-Urin or with empirically chosen parameters give an approximately similar correspondence of calculated values GITAsub(γ)sup(p) to experimental data [ru
International Nuclear Information System (INIS)
Sesnic, S.S.; Bitter, M.; Hill, K.W.; Hiroe, S.; Hulse, R.; Shimada, M.; Stratton, B.; von Goeler, S.
1986-05-01
The soft x-ray continuum radiation in TFTR low density neutral beam discharges can be much lower than its theoretical value obtained by assuming a corona equilibrium. This reduced continuum radiation is caused by an ionization equilibrium shift toward lower states, which strongly changes the value of the average recombination coefficient of metallic impurities anti γ, even for only slight changes in the average charge, anti Z. The primary agent for this shift is the charge exchange between the highly ionized impurity ions and the neutral hydrogen, rather than impurity transport, because the central density of the neutral hydrogen is strongly enhanced at lower plasma densities with intense beam injection. In the extreme case of low density, high neutral beam power TFTR operation (energetic ion mode) the reduction in anti γ can be as much as one-half to two-thirds. We calculate the parametric dependence of anti γ and anti Z for Ti, Cr, Fe, and Ni impurities on neutral density (equivalent to beam power), electron temperature, and electron density. These values are obtained by using either a one-dimensional impurity transport code (MIST) or a zero-dimensional code with a finite particle confinement time. As an example, we show the variation of anti γ and anti Z in different TFTR discharges
Ultra flat ideal concentrators of high concentration
Energy Technology Data Exchange (ETDEWEB)
Chaves, Julio [IST, Physics Dept., Lisboa (Portugal); INETI-DER, Lisboa (Portugal); Collares-Pereira, Manuel [INETI-DER, Lisboa (Portugal)
2000-07-01
A new method for the design of nonimaging devices is presented. Its application to the design of ultra flat compact concentrators is analysed. These new concentrators are based on a combination of two stages: the first one is composed of a large number of small structures placed side by side and the second one is a very compact single device concentrating the radiation to the limit. These devices are ideal for 2D. These compact designs are much more compact than the traditional ones like lens-mirror combinations or parabolic primaries with nonimaging secondaries. Besides, they can be designed for any acceptance angle, while the traditional ones are limited to small acceptance angles. (Author)
Highly concentrating Fresnel lenses
International Nuclear Information System (INIS)
Kritchman, E.M.; Friesem, A.A.; Yekutieli, G.
1979-01-01
A new type of concave Fresnel lens capable of concentrating solar radiation very near the ultimate concentration limit is considered. The differential equations that describe the lens are solved to provide computed solutions which are then checked by ray tracing techniques. The performance (efficiency and concentration) of the lens is investigated and compared to that of a flat Fresnel lens, showing that the new lens is preferable for concentrating solar radiation. (author)
Solar cell concentrating system
International Nuclear Information System (INIS)
Garg, H.P.; Sharma, V.K.; Agarwal, R.K.
1986-11-01
This study reviews fabrication techniques and testing facilities for different solar cells under concentration which have been developed and tested. It is also aimed to examine solar energy concentrators which are prospective candidates for photovoltaic concentrator systems. This may provide an impetus to the scientists working in the area of solar cell technology
Rheology of concentrated biomass
J.R. Samaniuk; J. Wang; T.W. Root; C.T. Scott; D.J. Klingenberg
2011-01-01
Economic processing of lignocellulosic biomass requires handling the biomass at high solids concentration. This creates challenges because concentrated biomass behaves as a Bingham-like material with large yield stresses. Here we employ torque rheometry to measure the rheological properties of concentrated lignocellulosic biomass (corn stover). Yield stresses obtained...
Energy Technology Data Exchange (ETDEWEB)
Semple, Sean; Apsley, Andrew; Moir, Gill; Henderson, George; Ayres, Jon, E-mail: sean.semple@abdn.ac.u [Department of Environmental and Occupational Medicine, Liberty Safe Work Research Centre, University of Aberdeen, Foresterhill Road, Aberdeen AB25 2ZP (United Kingdom)
2009-02-01
Second-hand tobacco smoke (SHS) exposure generates a large public health burden. Recent legislation has moved to prohibit smoking in public places and there are concerns that this may lead to an increase in exposures in private homes. Measurement of SHS aerosol has tended to use active pumped samples or longer-term diffusive badges. Pumped methods are noisy and poorly tolerated in home settings while diffusive badges do not provide real-time data. The UCB particle monitor (UCB-PM) is a modified smoke-alarm device capable of logging changes in airborne particulate matter over extended periods and has been used successfully to measure biomass fuel smoke concentrations in developing world settings This study has examined the use of the UCB-PM to measure SHS aerosol in both controlled laboratory conditions and a pilot field trial over a 7 day period in a smoker's home. Comparisons with a pumped sampler (TSI Sidepak Personal Aerosol Monitor) indicate good agreement over a range of exposure concentrations but there is evidence of a threshold effect at approximately 0.5 mg/m{sup 3} of fine particulate measured as PM{sub 2.5}. While this threshold effect undermines the ability of the device to provide useful data on the time-weighted average SHS concentration, the field trial indicates that that the UCB-PM has a sensitivity of about 71% and a specificity of 98%. The device has many advantages including zero noise operation, low cost and long battery life and may be a useful tool in quitting and smoke-free home intervention studies.
Average glandular dose in digital mammography and breast tomosynthesis
Energy Technology Data Exchange (ETDEWEB)
Olgar, T. [Ankara Univ. (Turkey). Dept. of Engineering Physics; Universitaetsklinikum Leipzig AoeR (Germany). Klinik und Poliklinik fuer Diagnostische und Interventionelle Radiologie; Kahn, T.; Gosch, D. [Universitaetsklinikum Leipzig AoeR (Germany). Klinik und Poliklinik fuer Diagnostische und Interventionelle Radiologie
2012-10-15
Purpose: To determine the average glandular dose (AGD) in digital full-field mammography (2 D imaging mode) and in breast tomosynthesis (3 D imaging mode). Materials and Methods: Using the method described by Boone, the AGD was calculated from the exposure parameters of 2247 conventional 2 D mammograms and 984 mammograms in 3 D imaging mode of 641 patients examined with the digital mammographic system Hologic Selenia Dimensions. The breast glandular tissue content was estimated by the Hologic R2 Quantra automated volumetric breast density measurement tool for each patient from right craniocaudal (RCC) and left craniocaudal (LCC) images in 2 D imaging mode. Results: The mean compressed breast thickness (CBT) was 52.7 mm for craniocaudal (CC) and 56.0 mm for mediolateral oblique (MLO) views. The mean percentage of breast glandular tissue content was 18.0 % and 17.4 % for RCC and LCC projections, respectively. The mean AGD values in 2 D imaging mode per exposure for the standard breast were 1.57 mGy and 1.66 mGy, while the mean AGD values after correction for real breast composition were 1.82 mGy and 1.94 mGy for CC and MLO views, respectively. The mean AGD values in 3 D imaging mode per exposure for the standard breast were 2.19 mGy and 2.29 mGy, while the mean AGD values after correction for the real breast composition were 2.53 mGy and 2.63 mGy for CC and MLO views, respectively. No significant relationship was found between the AGD and CBT in 2 D imaging mode and a good correlation coefficient of 0.98 in 3 D imaging mode. Conclusion: In this study the mean calculated AGD per exposure in 3 D imaging mode was on average 34 % higher than for 2 D imaging mode for patients examined with the same CBT.
Average glandular dose in digital mammography and breast tomosynthesis
International Nuclear Information System (INIS)
Olgar, T.; Universitaetsklinikum Leipzig AoeR; Kahn, T.; Gosch, D.
2012-01-01
Purpose: To determine the average glandular dose (AGD) in digital full-field mammography (2 D imaging mode) and in breast tomosynthesis (3 D imaging mode). Materials and Methods: Using the method described by Boone, the AGD was calculated from the exposure parameters of 2247 conventional 2 D mammograms and 984 mammograms in 3 D imaging mode of 641 patients examined with the digital mammographic system Hologic Selenia Dimensions. The breast glandular tissue content was estimated by the Hologic R2 Quantra automated volumetric breast density measurement tool for each patient from right craniocaudal (RCC) and left craniocaudal (LCC) images in 2 D imaging mode. Results: The mean compressed breast thickness (CBT) was 52.7 mm for craniocaudal (CC) and 56.0 mm for mediolateral oblique (MLO) views. The mean percentage of breast glandular tissue content was 18.0 % and 17.4 % for RCC and LCC projections, respectively. The mean AGD values in 2 D imaging mode per exposure for the standard breast were 1.57 mGy and 1.66 mGy, while the mean AGD values after correction for real breast composition were 1.82 mGy and 1.94 mGy for CC and MLO views, respectively. The mean AGD values in 3 D imaging mode per exposure for the standard breast were 2.19 mGy and 2.29 mGy, while the mean AGD values after correction for the real breast composition were 2.53 mGy and 2.63 mGy for CC and MLO views, respectively. No significant relationship was found between the AGD and CBT in 2 D imaging mode and a good correlation coefficient of 0.98 in 3 D imaging mode. Conclusion: In this study the mean calculated AGD per exposure in 3 D imaging mode was on average 34 % higher than for 2 D imaging mode for patients examined with the same CBT.
Relationships between feeding behavior and average daily gain in cattle
Directory of Open Access Journals (Sweden)
Bruno Fagundes Cunha Lage
2013-12-01
Full Text Available Several studies have reported relationship between eating behavior and performance in feedlot cattle. The evaluation of behavior traits demands high degree of work and trained manpower, therefore, in recent years has been used an automated feed intake measurement system (GrowSafe System ®, that identify and record individual feeding patterns. The aim of this study was to evaluate the relationship between feeding behavior traits and average daily gain in Nellore calves undergoing feed efficiency test. Date from 85 Nelore males was recorded during the feed efficiency test performed in 2012, at Centro APTA Bovinos de Corte, Instituto de Zootecnia, São Paulo State. Were analyzed the behavioral traits: time at feeder (TF, head down duration (HD, representing the time when the animal is actually eating, frequency of visits (FV and feed rate (FR calculated as the amount of dry matter (DM consumed by time at feeder (g.min-1. The ADG was calculated by linear regression of individual weights on days in test. ADG classes were obtained considering the average ADG and standard deviation (SD being: high ADG (>mean + 1.0 SD, medium ADG (± 1.0 SD from the mean and low ADG (
Strengthened glass for high average power laser applications
International Nuclear Information System (INIS)
Cerqua, K.A.; Lindquist, A.; Jacobs, S.D.; Lambropoulos, J.
1987-01-01
Recent advancements in high repetition rate and high average power laser systems have put increasing demands on the development of improved solid state laser materials with high thermal loading capabilities. The authors have developed a process for strengthening a commercially available Nd doped phosphate glass utilizing an ion-exchange process. Results of thermal loading fracture tests on moderate size (160 x 15 x 8 mm) glass slabs have shown a 6-fold improvement in power loading capabilities for strengthened samples over unstrengthened slabs. Fractographic analysis of post-fracture samples has given insight into the mechanism of fracture in both unstrengthened and strengthened samples. Additional stress analysis calculations have supported these findings. In addition to processing the glass' surface during strengthening in a manner which preserves its post-treatment optical quality, the authors have developed an in-house optical fabrication technique utilizing acid polishing to minimize subsurface damage in samples prior to exchange treatment. Finally, extension of the strengthening process to alternate geometries of laser glass has produced encouraging results, which may expand the potential or strengthened glass in laser systems, making it an exciting prospect for many applications
Perceptual learning in Williams syndrome: looking beyond averages.
Directory of Open Access Journals (Sweden)
Patricia Gervan
Full Text Available Williams Syndrome is a genetically determined neurodevelopmental disorder characterized by an uneven cognitive profile and surprisingly large neurobehavioral differences among individuals. Previous studies have already shown different forms of memory deficiencies and learning difficulties in WS. Here we studied the capacity of WS subjects to improve their performance in a basic visual task. We employed a contour integration paradigm that addresses occipital visual function, and analyzed the initial (i.e. baseline and after-learning performance of WS individuals. Instead of pooling the very inhomogeneous results of WS subjects together, we evaluated individual performance by expressing it in terms of the deviation from the average performance of the group of typically developing subjects of similar age. This approach helped us to reveal information about the possible origins of poor performance of WS subjects in contour integration. Although the majority of WS individuals showed both reduced baseline and reduced learning performance, individual analysis also revealed a dissociation between baseline and learning capacity in several WS subjects. In spite of impaired initial contour integration performance, some WS individuals presented learning capacity comparable to learning in the typically developing population, and vice versa, poor learning was also observed in subjects with high initial performance levels. These data indicate a dissociation between factors determining initial performance and perceptual learning.
Statistical properties of the gyro-averaged standard map
da Fonseca, Julio D.; Sokolov, Igor M.; Del-Castillo-Negrete, Diego; Caldas, Ibere L.
2015-11-01
A statistical study of the gyro-averaged standard map (GSM) is presented. The GSM is an area preserving map model proposed in as a simplified description of finite Larmor radius (FLR) effects on ExB chaotic transport in magnetized plasmas with zonal flows perturbed by drift waves. The GSM's effective perturbation parameter, gamma, is proportional to the zero-order Bessel function of the particle's Larmor radius. In the limit of zero Larmor radius, the GSM reduces to the standard, Chirikov-Taylor map. We consider plasmas in thermal equilibrium and assume a Larmor radius' probability density function (pdf) resulting from a Maxwell-Boltzmann distribution. Since the particles have in general different Larmor radii, each orbit is computed using a different perturbation parameter, gamma. We present analytical and numerical computations of the pdf of gamma for a Maxwellian distribution. We also compute the pdf of global chaos, which gives the probability that a particle with a given Larmor radius exhibits global chaos, i.e. the probability that Kolmogorov-Arnold-Moser (KAM) transport barriers do not exist.
The dynamics of multimodal integration: The averaging diffusion model.
Turner, Brandon M; Gao, Juan; Koenig, Scott; Palfy, Dylan; L McClelland, James
2017-12-01
We combine extant theories of evidence accumulation and multi-modal integration to develop an integrated framework for modeling multimodal integration as a process that unfolds in real time. Many studies have formulated sensory processing as a dynamic process where noisy samples of evidence are accumulated until a decision is made. However, these studies are often limited to a single sensory modality. Studies of multimodal stimulus integration have focused on how best to combine different sources of information to elicit a judgment. These studies are often limited to a single time point, typically after the integration process has occurred. We address these limitations by combining the two approaches. Experimentally, we present data that allow us to study the time course of evidence accumulation within each of the visual and auditory domains as well as in a bimodal condition. Theoretically, we develop a new Averaging Diffusion Model in which the decision variable is the mean rather than the sum of evidence samples and use it as a base for comparing three alternative models of multimodal integration, allowing us to assess the optimality of this integration. The outcome reveals rich individual differences in multimodal integration: while some subjects' data are consistent with adaptive optimal integration, reweighting sources of evidence as their relative reliability changes during evidence integration, others exhibit patterns inconsistent with optimality.
A Single Image Dehazing Method Using Average Saturation Prior
Directory of Open Access Journals (Sweden)
Zhenfei Gu
2017-01-01
Full Text Available Outdoor images captured in bad weather are prone to yield poor visibility, which is a fatal problem for most computer vision applications. The majority of existing dehazing methods rely on an atmospheric scattering model and therefore share a common limitation; that is, the model is only valid when the atmosphere is homogeneous. In this paper, we propose an improved atmospheric scattering model to overcome this inherent limitation. By adopting the proposed model, a corresponding dehazing method is also presented. In this method, we first create a haze density distribution map of a hazy image, which enables us to segment the hazy image into scenes according to the haze density similarity. Then, in order to improve the atmospheric light estimation accuracy, we define an effective weight assignment function to locate a candidate scene based on the scene segmentation results and therefore avoid most potential errors. Next, we propose a simple but powerful prior named the average saturation prior (ASP, which is a statistic of extensive high-definition outdoor images. Using this prior combined with the improved atmospheric scattering model, we can directly estimate the scene atmospheric scattering coefficient and restore the scene albedo. The experimental results verify that our model is physically valid, and the proposed method outperforms several state-of-the-art single image dehazing methods in terms of both robustness and effectiveness.
Average chewing pattern improvements following Disclusion Time reduction.
Kerstein, Robert B; Radke, John
2017-05-01
Studies involving electrognathographic (EGN) recordings of chewing improvements obtained following occlusal adjustment therapy are rare, as most studies lack 'chewing' within the research. The objectives of this study were to determine if reducing long Disclusion Time to short Disclusion Time with the immediate complete anterior guidance development (ICAGD) coronoplasty in symptomatic subjects altered their average chewing pattern (ACP) and their muscle function. Twenty-nine muscularly symptomatic subjects underwent simultaneous EMG and EGN recordings of right and left gum chewing, before and after the ICAGD coronoplasty. Statistical differences in the mean Disclusion Time, the mean muscle contraction cycle, and the mean ACP resultant from ICAGD underwent the Student's paired t-test (α = 0.05). Disclusion Time reductions from ICAGD were significant (2.11-0.45 s. p = 0.0000). Post-ICAGD muscle changes were significant in the mean area (p = 0.000001), the peak amplitude (p = 0.00005), the time to peak contraction (p chewing position became closer to centric occlusion (p chewing velocities increased (p chewing pattern (ACP) shape, speed, consistency, muscular coordination, and vertical opening improvements can be significantly improved in muscularly dysfunctional TMD patients within one week's time of undergoing the ICAGD enameloplasty. Computer-measured and guided occlusal adjustments quickly and physiologically improved chewing, without requiring the patients to wear pre- or post-treatment appliances.
Mean link versus average plaquette tadpoles in lattice NRQCD
International Nuclear Information System (INIS)
Shakespeare, Norman H.; Trottier, Howard D.
1999-01-01
We compare mean-link and average plaquette tadpole renormalization schemes in the context of the quarkonium hyperfine splittings in lattice NRQCD. Simulations are done for the three quarkonium systems cc-bar, bc-bar, and bb-bar. The hyperfine splittings are computed both at leading and at next-to-leading order in the relativistic expansion. Results are obtained at a large number of lattice spacings. A number of features emerge, all of which favor tadpole renormalization using mean links. This includes much better scaling of the hyperfine splittings in the three quarkonium systems. We also find that relativistic corrections to the spin splittings are smaller with mean-link tadpoles, particularly for the cc-bar and bc-bar systems. We also see signs of a breakdown in the NRQCD expansion when the bare quark mass falls below about one in lattice units (with the bare quark masses turning out to be much larger with mean-link tadpoles)
Mean link versus average plaquette tadpoles in lattice NRQCD
Energy Technology Data Exchange (ETDEWEB)
Shakespeare, Norman H.; Trottier, Howard D
1999-03-01
We compare mean-link and average plaquette tadpole renormalization schemes in the context of the quarkonium hyperfine splittings in lattice NRQCD. Simulations are done for the three quarkonium systems cc-bar, bc-bar, and bb-bar. The hyperfine splittings are computed both at leading and at next-to-leading order in the relativistic expansion. Results are obtained at a large number of lattice spacings. A number of features emerge, all of which favor tadpole renormalization using mean links. This includes much better scaling of the hyperfine splittings in the three quarkonium systems. We also find that relativistic corrections to the spin splittings are smaller with mean-link tadpoles, particularly for the cc-bar and bc-bar systems. We also see signs of a breakdown in the NRQCD expansion when the bare quark mass falls below about one in lattice units (with the bare quark masses turning out to be much larger with mean-link tadpoles)
Orientation-averaged optical properties of natural aerosol aggregates
International Nuclear Information System (INIS)
Zhang Xiaolin; Huang Yinbo; Rao Ruizhong
2012-01-01
Orientation-averaged optical properties of natural aerosol aggregates were analyzed by using discrete dipole approximation (DDA) for the effective radius in the range of 0.01 to 2 μm with the corresponding size parameter from 0.1 to 23 for the wavelength of 0.55 μm. Effects of the composition and morphology on the optical properties were also investigated. The composition show small influence on the extinction-efficiency factor in Mie scattering region, scattering- and backscattering-efficiency factors. The extinction-efficiency factor with the size parameter from 9 to 23 and asymmetry factor with the size parameter below 2.3 are almost independent of the natural aerosol composition. The extinction-, absorption, scattering-, and backscattering-efficiency factors with the size parameter below 0.7 are irrespective of the aggregate morphology. The intrinsic symmetry and discontinuity of the normal direction of the particle surface have obvious effects on the scattering properties for the size parameter above 4.6. Furthermore, the scattering phase functions of natural aerosol aggregates are enhanced at the backscattering direction (opposition effect) for large size parameters in the range of Mie scattering. (authors)
Principles of resonance-averaged gamma-ray spectroscopy
International Nuclear Information System (INIS)
Chrien, R.E.
1981-01-01
The unambiguous determination of excitation energies, spins, parities, and other properties of nuclear levels is the paramount goal of the nuclear spectroscopist. All developments of nuclear models depend upon the availability of a reliable data base on which to build. In this regard, slow neutron capture gamma-ray spectroscopy has proved to be a valuable tool. The observation of primary radiative transitions connecting initial and final states can provide definite level positions. In particular the use of the resonance-averaged capture technique has received much recent attention because of the claims advanced for this technique (Chrien 1980a, Casten 1980); that it is able to identify all states in a given spin-parity range and to provide definite spin parity information for these states. In view of the importance of this method, it is perhaps surprising that until now no firm analytical basis has been provided which delineates its capabilities and limitations. Such an analysis is necessary to establish the spin-parity assignments derived from this method on a quantitative basis; in other words a quantitative statement of the limits of error must be provided. It is the principal aim of the present paper to present such an analysis. To do this, a historical description of the technique and its applications is presented and the principles of the method are stated. Finally a method of statistical analysis is described, and the results are applied to recent measurements carried out at the filtered beam facilities at the Brookhaven National Laboratory
Potential of high-average-power solid state lasers
International Nuclear Information System (INIS)
Emmett, J.L.; Krupke, W.F.; Sooy, W.R.
1984-01-01
We discuss the possibility of extending solid state laser technology to high average power and of improving the efficiency of such lasers sufficiently to make them reasonable candidates for a number of demanding applications. A variety of new design concepts, materials, and techniques have emerged over the past decade that, collectively, suggest that the traditional technical limitations on power (a few hundred watts or less) and efficiency (less than 1%) can be removed. The core idea is configuring the laser medium in relatively thin, large-area plates, rather than using the traditional low-aspect-ratio rods or blocks. This presents a large surface area for cooling, and assures that deposited heat is relatively close to a cooled surface. It also minimizes the laser volume distorted by edge effects. The feasibility of such configurations is supported by recent developments in materials, fabrication processes, and optical pumps. Two types of lasers can, in principle, utilize this sheet-like gain configuration in such a way that phase and gain profiles are uniformly sampled and, to first order, yield high-quality (undistorted) beams. The zig-zag laser does this with a single plate, and should be capable of power levels up to several kilowatts. The disk laser is designed around a large number of plates, and should be capable of scaling to arbitrarily high power levels
Accelerated Distributed Dual Averaging Over Evolving Networks of Growing Connectivity
Liu, Sijia; Chen, Pin-Yu; Hero, Alfred O.
2018-04-01
We consider the problem of accelerating distributed optimization in multi-agent networks by sequentially adding edges. Specifically, we extend the distributed dual averaging (DDA) subgradient algorithm to evolving networks of growing connectivity and analyze the corresponding improvement in convergence rate. It is known that the convergence rate of DDA is influenced by the algebraic connectivity of the underlying network, where better connectivity leads to faster convergence. However, the impact of network topology design on the convergence rate of DDA has not been fully understood. In this paper, we begin by designing network topologies via edge selection and scheduling. For edge selection, we determine the best set of candidate edges that achieves the optimal tradeoff between the growth of network connectivity and the usage of network resources. The dynamics of network evolution is then incurred by edge scheduling. Further, we provide a tractable approach to analyze the improvement in the convergence rate of DDA induced by the growth of network connectivity. Our analysis reveals the connection between network topology design and the convergence rate of DDA, and provides quantitative evaluation of DDA acceleration for distributed optimization that is absent in the existing analysis. Lastly, numerical experiments show that DDA can be significantly accelerated using a sequence of well-designed networks, and our theoretical predictions are well matched to its empirical convergence behavior.
Surfactant Effect on the Average Flow Generation Near Curved Interface
Klimenko, Lyudmila; Lyubimov, Dmitry
2018-02-01
The present work is devoted to the average flow generation near curved interface with a surfactant adsorbed on the surface layer. The investigation was carried out for a liquid drop embedded in a viscous liquid with a different density. The liquid flows inside and outside the drop are generated by small amplitude and high frequency vibrations. Surfactant exchange between the drop surface and the surrounding liquid is limited by the process of adsorption-desorption. It was assumed that the surfactant is soluble in the surrounding liquid, but not soluble in the liquid drop. Surrounding liquid and the liquid in the drop are considered incompressible. Normal and shear viscous stresses balance at the interface is performed under the condition that the film thickness of the adsorbed surfactant is negligible. The problem is solved under assumption that the shape of the drop in the presence of adsorbed surfactant remains spherical symmetry. The effective boundary conditions for the tangential velocity jump and shear stress jump, describing the above generation have been obtained by matched asymptotic expansions method. The conditions under which the drop surface can be considered as a quasi-solid are determined. It is shown that in the case of the significant effect of surfactant on the surface tension, the dominant mechanism for the generation is the Schlichting mechanisms under vibrations.
Ensemble bayesian model averaging using markov chain Monte Carlo sampling
Energy Technology Data Exchange (ETDEWEB)
Vrugt, Jasper A [Los Alamos National Laboratory; Diks, Cees G H [NON LANL; Clark, Martyn P [NON LANL
2008-01-01
Bayesian model averaging (BMA) has recently been proposed as a statistical method to calibrate forecast ensembles from numerical weather models. Successful implementation of BMA however, requires accurate estimates of the weights and variances of the individual competing models in the ensemble. In their seminal paper (Raftery etal. Mon Weather Rev 133: 1155-1174, 2(05)) has recommended the Expectation-Maximization (EM) algorithm for BMA model training, even though global convergence of this algorithm cannot be guaranteed. In this paper, we compare the performance of the EM algorithm and the recently developed Differential Evolution Adaptive Metropolis (DREAM) Markov Chain Monte Carlo (MCMC) algorithm for estimating the BMA weights and variances. Simulation experiments using 48-hour ensemble data of surface temperature and multi-model stream-flow forecasts show that both methods produce similar results, and that their performance is unaffected by the length of the training data set. However, MCMC simulation with DREAM is capable of efficiently handling a wide variety of BMA predictive distributions, and provides useful information about the uncertainty associated with the estimated BMA weights and variances.
Average accelerator simulation Truebeam using phase space in IAEA format
International Nuclear Information System (INIS)
Santana, Emico Ferreira; Milian, Felix Mas; Paixao, Paulo Oliveira; Costa, Raranna Alves da; Velasco, Fermin Garcia
2015-01-01
In this paper is used a computational code of radiation transport simulation based on Monte Carlo technique, in order to model a linear accelerator of treatment by Radiotherapy. This work is the initial step of future proposals which aim to study several treatment of patient by Radiotherapy, employing computational modeling in cooperation with the institutions UESC, IPEN, UFRJ e COI. The Chosen simulation code is GATE/Geant4. The average accelerator is TrueBeam of Varian Company. The geometric modeling was based in technical manuals, and radiation sources on the phase space for photons, provided by manufacturer in the IAEA (International Atomic Energy Agency) format. The simulations were carried out in equal conditions to experimental measurements. Were studied photons beams of 6MV, with 10 per 10 cm of field, focusing on a water phantom. For validation were compared dose curves in depth, lateral profiles in different depths of the simulated results and experimental data. The final modeling of this accelerator will be used in future works involving treatments and real patients. (author)
Sedimentological regimes for turbidity currents: Depth-averaged theory
Halsey, Thomas C.; Kumar, Amit; Perillo, Mauricio M.
2017-07-01
Turbidity currents are one of the most significant means by which sediment is moved from the continents into the deep ocean; their properties are interesting both as elements of the global sediment cycle and due to their role in contributing to the formation of deep water oil and gas reservoirs. One of the simplest models of the dynamics of turbidity current flow was introduced three decades ago, and is based on depth-averaging of the fluid mechanical equations governing the turbulent gravity-driven flow of relatively dilute turbidity currents. We examine the sedimentological regimes of a simplified version of this model, focusing on the role of the Richardson number Ri [dimensionless inertia] and Rouse number Ro [dimensionless sedimentation velocity] in determining whether a current is net depositional or net erosional. We find that for large Rouse numbers, the currents are strongly net depositional due to the disappearance of local equilibria between erosion and deposition. At lower Rouse numbers, the Richardson number also plays a role in determining the degree of erosion versus deposition. The currents become more erosive at lower values of the product Ro × Ri, due to the effect of clear water entrainment. At higher values of this product, the turbulence becomes insufficient to maintain the sediment in suspension, as first pointed out by Knapp and Bagnold. We speculate on the potential for two-layer solutions in this insufficiently turbulent regime, which would comprise substantial bedload flow with an overlying turbidity current.
Measurement of the average lifetime of hadrons containing bottom quarks
International Nuclear Information System (INIS)
Klem, D.E.
1986-06-01
This thesis reports a measurement of the average lifetime of hadrons containing bottom quarks. It is based on data taken with the DELCO detector at the PEP e + e - storage ring at a center of mass energy of 29 GeV. The decays of hadrons containing bottom quarks are tagged in hadronic events by the presence of electrons with a large component of momentum transverse to the event axis. Such electrons are identified in the DELCO detector by an atmospheric pressure Cherenkov counter assisted by a lead/scintillator electromagnetic shower counter. The lifetime measured is 1.17 psec, consistent with previous measurements. This measurement, in conjunction with a limit on the non-charm branching ratio in b-decay obtained by other experiments, can be used to constrain the magnitude of the V/sub cb/ element of the Kobayashi-Maskawa matrix to the range 0.042 (+0.005 or -0.004 (stat.), +0.004 or -0.002 (sys.)), where the errors reflect the uncertainty on tau/sub b/ only and not the uncertainties in the calculations which relate the b-lifetime and the element of the Kobayashi-Maskawa matrix
Theory of time-averaged neutral dynamics with environmental stochasticity
Danino, Matan; Shnerb, Nadav M.
2018-04-01
Competition is the main driver of population dynamics, which shapes the genetic composition of populations and the assembly of ecological communities. Neutral models assume that all the individuals are equivalent and that the dynamics is governed by demographic (shot) noise, with a steady state species abundance distribution (SAD) that reflects a mutation-extinction equilibrium. Recently, many empirical and theoretical studies emphasized the importance of environmental variations that affect coherently the relative fitness of entire populations. Here we consider two generic time-averaged neutral models; in both the relative fitness of each species fluctuates independently in time but its mean is zero. The first (model A) describes a system with local competition and linear fitness dependence of the birth-death rates, while in the second (model B) the competition is global and the fitness dependence is nonlinear. Due to this nonlinearity, model B admits a noise-induced stabilization mechanism that facilitates the invasion of new mutants. A self-consistent mean-field approach is used to reduce the multispecies problem to two-species dynamics, and the large-N asymptotics of the emerging set of Fokker-Planck equations is presented and solved. Our analytic expressions are shown to fit the SADs obtained from extensive Monte Carlo simulations and from numerical solutions of the corresponding master equations.
Beamforming using subspace estimation from a diagonally averaged sample covariance.
Quijano, Jorge E; Zurk, Lisa M
2017-08-01
The potential benefit of a large-aperture sonar array for high resolution target localization is often challenged by the lack of sufficient data required for adaptive beamforming. This paper introduces a Toeplitz-constrained estimator of the clairvoyant signal covariance matrix corresponding to multiple far-field targets embedded in background isotropic noise. The estimator is obtained by averaging along subdiagonals of the sample covariance matrix, followed by covariance extrapolation using the method of maximum entropy. The sample covariance is computed from limited data snapshots, a situation commonly encountered with large-aperture arrays in environments characterized by short periods of local stationarity. Eigenvectors computed from the Toeplitz-constrained covariance are used to construct signal-subspace projector matrices, which are shown to reduce background noise and improve detection of closely spaced targets when applied to subspace beamforming. Monte Carlo simulations corresponding to increasing array aperture suggest convergence of the proposed projector to the clairvoyant signal projector, thereby outperforming the classic projector obtained from the sample eigenvectors. Beamforming performance of the proposed method is analyzed using simulated data, as well as experimental data from the Shallow Water Array Performance experiment.
Determination of the average lifetime of b-baryons
Abreu, P; Adye, T; Agasi, E; Ajinenko, I; Aleksan, Roy; Alekseev, G D; Alemany, R; Allport, P P; Almehed, S; Amaldi, Ugo; Amato, S; Andreazza, A; Andrieux, M L; Antilogus, P; Apel, W D; Arnoud, Y; Åsman, B; Augustin, J E; Augustinus, A; Baillon, Paul; Bambade, P; Barão, F; Barate, R; Barbi, M S; Bardin, Dimitri Yuri; Baroncelli, A; Bärring, O; Barrio, J A; Bartl, Walter; Bates, M J; Battaglia, Marco; Baubillier, M; Baudot, J; Becks, K H; Begalli, M; Beillière, P; Belokopytov, Yu A; Belous, K S; Benvenuti, Alberto C; Berggren, M; Bertrand, D; Bianchi, F; Bigi, M; Bilenky, S M; Billoir, P; Bloch, D; Blume, M; Blyth, S; Bolognese, T; Bonesini, M; Bonivento, W; Booth, P S L; Borisov, G; Bosio, C; Bosworth, S; Botner, O; Boudinov, E; Bouquet, B; Bourdarios, C; Bowcock, T J V; Bozzo, M; Branchini, P; Brand, K D; Brenke, T; Brenner, R A; Bricman, C; Brillault, L; Brown, R C A; Brückman, P; Brunet, J M; Bugge, L; Buran, T; Burgsmüller, T; Buschmann, P; Buys, A; Cabrera, S; Caccia, M; Calvi, M; Camacho-Rozas, A J; Camporesi, T; Canale, V; Canepa, M; Cankocak, K; Cao, F; Carena, F; Carroll, L; Caso, Carlo; Castillo-Gimenez, M V; Cattai, A; Cavallo, F R; Cerrito, L; Chabaud, V; Chapkin, M M; Charpentier, P; Chaussard, L; Chauveau, J; Checchia, P; Chelkov, G A; Chen, M; Chierici, R; Chliapnikov, P V; Chochula, P; Chorowicz, V; Chudoba, J; Cindro, V; Collins, P; Contreras, J L; Contri, R; Cortina, E; Cosme, G; Cossutti, F; Crawley, H B; Crennell, D J; Crosetti, G; Cuevas-Maestro, J; Czellar, S; Dahl-Jensen, Erik; Dahm, J; D'Almagne, B; Dam, M; Damgaard, G; Dauncey, P D; Davenport, Martyn; Da Silva, W; Defoix, C; Deghorain, A; Della Ricca, G; Delpierre, P A; Demaria, N; De Angelis, A; de Boer, Wim; De Brabandere, S; De Clercq, C; La Vaissière, C de; De Lotto, B; De Min, A; De Paula, L S; De Saint-Jean, C; Dijkstra, H; Di Ciaccio, Lucia; Djama, F; Dolbeau, J; Dönszelmann, M; Doroba, K; Dracos, M; Drees, J; Drees, K A; Dris, M; Dufour, Y; Edsall, D M; Ehret, R; Eigen, G; Ekelöf, T J C; Ekspong, Gösta; Elsing, M; Engel, J P; Ershaidat, N; Erzen, B; Falk, E; Fassouliotis, D; Feindt, Michael; Ferrer, A; Filippas-Tassos, A; Firestone, A; Fischer, P A; Föth, H; Fokitis, E; Fontanelli, F; Formenti, F; Franek, B J; Frenkiel, P; Fries, D E C; Frodesen, A G; Frühwirth, R; Fulda-Quenzer, F; Fuster, J A; Galloni, A; Gamba, D; Gandelman, M; García, C; García, J; Gaspar, C; Gasparini, U; Gavillet, P; Gazis, E N; Gelé, D; Gerber, J P; Gerdyukov, L N; Gibbs, M; Gokieli, R; Golob, B; Gopal, Gian P; Gorn, L; Górski, M; Guz, Yu; Gracco, Valerio; Graziani, E; Grosdidier, G; Grzelak, K; Gumenyuk, S A; Gunnarsson, P; Günther, M; Guy, J; Hahn, F; Hahn, S; Hajduk, Z; Hallgren, A; Hamacher, K; Hao, W; Harris, F J; Hedberg, V; Henriques, R P; Hernández, J J; Herquet, P; Herr, H; Hessing, T L; Higón, E; Hilke, Hans Jürgen; Hill, T S; Holmgren, S O; Holt, P J; Holthuizen, D J; Hoorelbeke, S; Houlden, M A; Hrubec, Josef; Huet, K; Hultqvist, K; Jackson, J N; Jacobsson, R; Jalocha, P; Janik, R; Jarlskog, C; Jarlskog, G; Jarry, P; Jean-Marie, B; Johansson, E K; Jönsson, L B; Jönsson, P E; Joram, Christian; Juillot, P; Kaiser, M; Kapusta, F; Karafasoulis, K; Karlsson, M; Karvelas, E; Katsanevas, S; Katsoufis, E C; Keränen, R; Khokhlov, Yu A; Khomenko, B A; Khovanskii, N N; King, B J; Kjaer, N J; Klein, H; Klovning, A; Kluit, P M; Köne, B; Kokkinias, P; Koratzinos, M; Korcyl, K; Kourkoumelis, C; Kuznetsov, O; Kramer, P H; Krammer, Manfred; Kreuter, C; Kronkvist, I J; Krumshtein, Z; Krupinski, W; Kubinec, P; Kucewicz, W; Kurvinen, K L; Lacasta, C; Laktineh, I; Lamblot, S; Lamsa, J; Lanceri, L; Lane, D W; Langefeld, P; Last, I; Laugier, J P; Lauhakangas, R; Leder, Gerhard; Ledroit, F; Lefébure, V; Legan, C K; Leitner, R; Lemoigne, Y; Lemonne, J; Lenzen, Georg; Lepeltier, V; Lesiak, T; Liko, D; Lindner, R; Lipniacka, A; Lippi, I; Lörstad, B; Loken, J G; López, J M; Loukas, D; Lutz, P; Lyons, L; MacNaughton, J N; Maehlum, G; Maio, A; Malychev, V; Mandl, F; Marco, J; Marco, R P; Maréchal, B; Margoni, M; Marin, J C; Mariotti, C; Markou, A; Maron, T; Martínez-Rivero, C; Martínez-Vidal, F; Martí i García, S; Masik, J; Matorras, F; Matteuzzi, C; Matthiae, Giorgio; Mazzucato, M; McCubbin, M L; McKay, R; McNulty, R; Medbo, J; Merk, M; Meroni, C; Meyer, S; Meyer, W T; Michelotto, M; Migliore, E; Mirabito, L; Mitaroff, Winfried A; Mjörnmark, U; Moa, T; Møller, R; Mönig, K; Monge, M R; Morettini, P; Müller, H; Mundim, L M; Murray, W J; Muryn, B; Myatt, Gerald; Naraghi, F; Navarria, Francesco Luigi; Navas, S; Nawrocki, K; Negri, P; Némécek, S; Neumann, W; Neumeister, N; Nicolaidou, R; Nielsen, B S; Nieuwenhuizen, M; Nikolaenko, V; Niss, P; Nomerotski, A; Normand, Ainsley; Oberschulte-Beckmann, W; Obraztsov, V F; Olshevskii, A G; Onofre, A; Orava, Risto; Österberg, K; Ouraou, A; Paganini, P; Paganoni, M; Pagès, P; Palka, H; Papadopoulou, T D; Papageorgiou, K; Pape, L; Parkes, C; Parodi, F; Passeri, A; Pegoraro, M; Peralta, L; Pernegger, H; Perrotta, A; Petridou, C; Petrolini, A; Petrovykh, M; Phillips, H T; Piana, G; Pierre, F; Pimenta, M; Pindo, M; Plaszczynski, S; Podobrin, O; Pol, M E; Polok, G; Poropat, P; Pozdnyakov, V; Prest, M; Privitera, P; Pukhaeva, N; Pullia, Antonio; Radojicic, D; Ragazzi, S; Rahmani, H; Ratoff, P N; Read, A L; Reale, M; Rebecchi, P; Redaelli, N G; Regler, Meinhard; Reid, D; Renton, P B; Resvanis, L K; Richard, F; Richardson, J; Rídky, J; Rinaudo, G; Ripp, I; Romero, A; Roncagliolo, I; Ronchese, P; Roos, L; Rosenberg, E I; Rosso, E; Roudeau, Patrick; Rovelli, T; Rückstuhl, W; Ruhlmann-Kleider, V; Ruiz, A; Rybicki, K; Saarikko, H; Sacquin, Yu; Sadovskii, A; Sajot, G; Salt, J; Sánchez, J; Sannino, M; Schimmelpfennig, M; Schneider, H; Schwickerath, U; Schyns, M A E; Sciolla, G; Scuri, F; Seager, P; Sedykh, Yu; Segar, A M; Seitz, A; Sekulin, R L; Shellard, R C; Siccama, I; Siegrist, P; Simonetti, S; Simonetto, F; Sissakian, A N; Sitár, B; Skaali, T B; Smadja, G; Smirnov, N; Smirnova, O G; Smith, G R; Solovyanov, O; Sosnowski, R; Souza-Santos, D; Spassoff, Tz; Spiriti, E; Sponholz, P; Squarcia, S; Stanescu, C; Stapnes, Steinar; Stavitski, I; Stichelbaut, F; Stocchi, A; Strauss, J; Strub, R; Stugu, B; Szczekowski, M; Szeptycka, M; Tabarelli de Fatis, T; Tavernet, J P; Chikilev, O G; Tilquin, A; Timmermans, J; Tkatchev, L G; Todorov, T; Toet, D Z; Tomaradze, A G; Tomé, B; Tonazzo, A; Tortora, L; Tranströmer, G; Treille, D; Trischuk, W; Tristram, G; Trombini, A; Troncon, C; Tsirou, A L; Turluer, M L; Tyapkin, I A; Tyndel, M; Tzamarias, S; Überschär, B; Ullaland, O; Uvarov, V; Valenti, G; Vallazza, E; Van der Velde, C; van Apeldoorn, G W; van Dam, P; Van Doninck, W K; Van Eldik, J; Vassilopoulos, N; Vegni, G; Ventura, L; Venus, W A; Verbeure, F; Verlato, M; Vertogradov, L S; Vilanova, D; Vincent, P; Vitale, L; Vlasov, E; Vodopyanov, A S; Vrba, V; Wahlen, H; Walck, C; Waldner, F; Weierstall, M; Weilhammer, Peter; Weiser, C; Wetherell, Alan M; Wicke, D; Wickens, J H; Wielers, M; Wilkinson, G R; Williams, W S C; Winter, M; Witek, M; Woschnagg, K; Yip, K; Yushchenko, O P; Zach, F; Zaitsev, A; Zalewska-Bak, A; Zalewski, Piotr; Zavrtanik, D; Zevgolatakos, E; Zimin, N I; Zito, M; Zontar, D; Zuberi, R; Zucchelli, G C; Zumerle, G; Belokopytov, Yu; Charpentier, Ph; Gavillet, Ph; Gouz, Yu; Jarlskog, Ch; Khokhlov, Yu; Papadopoulou, Th D
1996-01-01
The average lifetime of b-baryons has been studied using 3 \\times 10^6 hadronic Z^0 decays collected by the DELPHI detector at LEP. Three methods have been used, based on the measurement of different observables: the proper decay time distribution of 206 vertices reconstructed with a \\Lambda, a lepton and an oppositely charged pion; the impact parameter distribution of 441 muons with high transverse momentum accompanied by a \\mLs in the same jet; and the proper decay time distribution of 125 \\Lambda_c-lepton decay vertices with the \\Lambda_c exclusively reconstructed through its pK\\pi, pK^0 and \\mLs3\\pi decay modes. The combined result is~:\\par \\begin{center} \\tau(b-baryon) = (1.25^{+0.13}_{-0.11}\\ pm0.04(syst)^{+0.03}_{-0. 05}(syst)) ps\\par \\end{center} where the first systematic error is due to experimental uncertainties and the second to the uncertainties in the modelling of the b-baryon production and semi-leptonic decay. Including the measurement recently published by DELPHI based on a sample of proton-m...
Plate with a hole obeys the averaged null energy condition
International Nuclear Information System (INIS)
Graham, Noah; Olum, Ken D.
2005-01-01
The negative energy density of Casimir systems appears to violate general relativity energy conditions. However, one cannot test the averaged null energy condition (ANEC) using standard calculations for perfectly reflecting plates, because the null geodesic would have to pass through the plates, where the calculation breaks down. To avoid this problem, we compute the contribution to ANEC for a geodesic that passes through a hole in a single plate. We consider both Dirichlet and Neumann boundary conditions in two and three space dimensions. We use a Babinet's principle argument to reduce the problem to a complementary finite disk correction to the perfect mirror result, which we then compute using scattering theory in elliptical and spheroidal coordinates. In the Dirichlet case, we find that the positive correction due to the hole overwhelms the negative contribution of the infinite plate. In the Neumann case, where the infinite plate gives a positive contribution, the hole contribution is smaller in magnitude, so again ANEC is obeyed. These results can be extended to the case of two plates in the limits of large and small hole radii. This system thus provides another example of a situation where ANEC turns out to be obeyed when one might expect it to be violated
Local and average structure of Mn- and La-substituted BiFeO{sub 3}
Energy Technology Data Exchange (ETDEWEB)
Jiang, Bo; Selbach, Sverre M., E-mail: selbach@ntnu.no
2017-06-15
The local and average structure of solid solutions of the multiferroic perovskite BiFeO{sub 3} is investigated by synchrotron X-ray diffraction (XRD) and electron density functional theory (DFT) calculations. The average experimental structure is determined by Rietveld refinement and the local structure by total scattering data analyzed in real space with the pair distribution function (PDF) method. With equal concentrations of La on the Bi site or Mn on the Fe site, La causes larger structural distortions than Mn. Structural models based on DFT relaxed geometry give an improved fit to experimental PDFs compared to models constrained by the space group symmetry. Berry phase calculations predict a higher ferroelectric polarization than the experimental literature values, reflecting that structural disorder is not captured in either average structure space group models or DFT calculations with artificial long range order imposed by periodic boundary conditions. Only by including point defects in a supercell, here Bi vacancies, can DFT calculations reproduce the literature results on the structure and ferroelectric polarization of Mn-substituted BiFeO{sub 3}. The combination of local and average structure sensitive experimental methods with DFT calculations is useful for illuminating the structure-property-composition relationships in complex functional oxides with local structural distortions. - Graphical abstract: The experimental and simulated partial pair distribution functions (PDF) for BiFeO{sub 3}, BiFe{sub 0.875}Mn{sub 0.125}O{sub 3}, BiFe{sub 0.75}Mn{sub 0.25}O{sub 3} and Bi{sub 0.9}La{sub 0.1}FeO{sub 3}.
Digital mammography screening: average glandular dose and first performance parameters
International Nuclear Information System (INIS)
Weigel, S.; Girnus, R.; Czwoydzinski, J.; Heindel, W.; Decker, T.; Spital, S.
2007-01-01
Purpose: The Radiation Protection Commission demanded structured implementation of digital mammography screening in Germany. The main requirements were the installation of digital reference centers and separate evaluation of the fully digitized screening units. Digital mammography screening must meet the quality standards of the European guidelines and must be compared to analog screening results. We analyzed early surrogate indicators of effective screening and dosage levels for the first German digital screening unit in a routine setting after the first half of the initial screening round. Materials and Methods: We used three digital mammography screening units (one full-field digital scanner [DR] and two computed radiography systems [CR]). Each system has been proven to fulfill the requirements of the National and European guidelines. The radiation exposure levels, the medical workflow and the histological results were documented in a central electronic screening record. Results: In the first year 11,413 women were screened (participation rate 57.5 %). The parenchymal dosages for the three mammographic X-ray systems, averaged for the different breast sizes, were 0.7 (DR), 1.3 (CR), 1.5 (CR) mGy. 7 % of the screened women needed to undergo further examinations. The total number of screen-detected cancers was 129 (detection rate 1.1 %). 21 % of the carcinomas were classified as ductal carcinomas in situ, 40 % of the invasive carcinomas had a histological size ≤ 10 mm and 61 % < 15 mm. The frequency distribution of pT-categories of screen-detected cancer was as follows: pTis 20.9 %, pT1 61.2 %, pT2 14.7 %, pT3 2.3 %, pT4 0.8 %. 73 % of the invasive carcinomas were node-negative. (orig.)
A spatially-averaged mathematical model of kidney branching morphogenesis
Zubkov, V.S.
2015-08-01
© 2015 Published by Elsevier Ltd. Kidney development is initiated by the outgrowth of an epithelial ureteric bud into a population of mesenchymal cells. Reciprocal morphogenetic responses between these two populations generate a highly branched epithelial ureteric tree with the mesenchyme differentiating into nephrons, the functional units of the kidney. While we understand some of the mechanisms involved, current knowledge fails to explain the variability of organ sizes and nephron endowment in mice and humans. Here we present a spatially-averaged mathematical model of kidney morphogenesis in which the growth of the two key populations is described by a system of time-dependant ordinary differential equations. We assume that branching is symmetric and is invoked when the number of epithelial cells per tip reaches a threshold value. This process continues until the number of mesenchymal cells falls below a critical value that triggers cessation of branching. The mathematical model and its predictions are validated against experimentally quantified C57Bl6 mouse embryonic kidneys. Numerical simulations are performed to determine how the final number of branches changes as key system parameters are varied (such as the growth rate of tip cells, mesenchyme cells, or component cell population exit rate). Our results predict that the developing kidney responds differently to loss of cap and tip cells. They also indicate that the final number of kidney branches is less sensitive to changes in the growth rate of the ureteric tip cells than to changes in the growth rate of the mesenchymal cells. By inference, increasing the growth rate of mesenchymal cells should maximise branch number. Our model also provides a framework for predicting the branching outcome when ureteric tip or mesenchyme cells change behaviour in response to different genetic or environmental developmental stresses.
The Lake Wobegon effect: are all cancer patients above average?
Wolf, Jacqueline H; Wolf, Kevin S
2013-12-01
When elderly patients face a terminal illness such as lung cancer, most are unaware that what we term in this article "the Lake Wobegon effect" taints the treatment advice imparted to them by their oncologists. In framing treatment plans, cancer specialists tend to intimate that elderly patients are like the children living in Garrison Keillor's mythical Lake Wobegon: above average and thus likely to exceed expectations. In this article, we use the story of our mother's death from lung cancer to investigate the consequences of elderly people's inability to reconcile the grave reality of their illness with the overly optimistic predictions of their physicians. In this narrative analysis, we examine the routine treatment of elderly, terminally ill cancer patients through alternating lenses: the lens of a historian of medicine who also teaches ethics to medical students and the lens of an actuary who is able to assess physicians' claims for the outcome of medical treatments. We recognize that a desire to instill hope in patients shapes physicians' messages. We argue, however, that the automatic optimism conveyed to elderly, dying patients by cancer specialists prompts those patients to choose treatment that is ineffective and debilitating. Rather than primarily prolong life, treatments most notably diminish patients' quality of life, weaken the ability of patients and their families to prepare for their deaths, and contribute significantly to the unsustainable costs of the U.S. health care system. The case described in this article suggests how physicians can better help elderly, terminally ill patients make medical decisions that are less damaging to them and less costly to the health care system. © 2013 Milbank Memorial Fund.
A spatially-averaged mathematical model of kidney branching morphogenesis
Zubkov, V.S.; Combes, A.N.; Short, K.M.; Lefevre, J.; Hamilton, N.A.; Smyth, I.M.; Little, M.H.; Byrne, H.M.
2015-01-01
© 2015 Published by Elsevier Ltd. Kidney development is initiated by the outgrowth of an epithelial ureteric bud into a population of mesenchymal cells. Reciprocal morphogenetic responses between these two populations generate a highly branched epithelial ureteric tree with the mesenchyme differentiating into nephrons, the functional units of the kidney. While we understand some of the mechanisms involved, current knowledge fails to explain the variability of organ sizes and nephron endowment in mice and humans. Here we present a spatially-averaged mathematical model of kidney morphogenesis in which the growth of the two key populations is described by a system of time-dependant ordinary differential equations. We assume that branching is symmetric and is invoked when the number of epithelial cells per tip reaches a threshold value. This process continues until the number of mesenchymal cells falls below a critical value that triggers cessation of branching. The mathematical model and its predictions are validated against experimentally quantified C57Bl6 mouse embryonic kidneys. Numerical simulations are performed to determine how the final number of branches changes as key system parameters are varied (such as the growth rate of tip cells, mesenchyme cells, or component cell population exit rate). Our results predict that the developing kidney responds differently to loss of cap and tip cells. They also indicate that the final number of kidney branches is less sensitive to changes in the growth rate of the ureteric tip cells than to changes in the growth rate of the mesenchymal cells. By inference, increasing the growth rate of mesenchymal cells should maximise branch number. Our model also provides a framework for predicting the branching outcome when ureteric tip or mesenchyme cells change behaviour in response to different genetic or environmental developmental stresses.
Declining average daily census. Part 1: Implications and options.
Weil, T P
1985-12-01
A national trend toward declining average daily (inpatient) census (ADC) started in late 1982 even before the Medicare prospective payment system began. The decrease in total days will continue despite an increasing number of aged persons in the U.S. population. This decline could have been predicted from trends during 1978 to 1983, such as increasing available beds but decreasing occupancy, 100 percent increases in hospital expenses, and declining lengths of stay. Assuming that health care costs will remain as a relatively fixed part of the gross national product and no major medical advances will occur in the next five years, certain implications and options exist for facilities experiencing a declining ADC. This article discusses several considerations: Attempts to improve market share; Reduction of full-time equivalent employees; Impact of greater acuity of illness among remaining inpatients; Implications of increasing the number of physicians on medical staffs; Option of a closed medical staff by clinical specialty; Unbundling with not-for-profit and profit-making corporations; Review of mergers, consolidations, and multihospital systems to decide when this option is most appropriate; Sale of a not-for-profit hospital to an investor-owned chain, with implications facing Catholic hospitals choosing this option; Impact and difficulty of developing meaningful alternative health care systems with the hospital's medical staff; Special problems of teaching hospitals; The social issue of the hospital shifting from the community's health center to a cost center; Increased turnover of hospital CEOs; With these in mind, institutions can then focus on solutions that can sometimes be used in tandem to resolve this problem's impact. The second part of this article will discuss some of them.
Identification and estimation of survivor average causal effects.
Tchetgen Tchetgen, Eric J
2014-09-20
In longitudinal studies, outcomes ascertained at follow-up are typically undefined for individuals who die prior to the follow-up visit. In such settings, outcomes are said to be truncated by death and inference about the effects of a point treatment or exposure, restricted to individuals alive at the follow-up visit, could be biased even if as in experimental studies, treatment assignment were randomized. To account for truncation by death, the survivor average causal effect (SACE) defines the effect of treatment on the outcome for the subset of individuals who would have survived regardless of exposure status. In this paper, the author nonparametrically identifies SACE by leveraging post-exposure longitudinal correlates of survival and outcome that may also mediate the exposure effects on survival and outcome. Nonparametric identification is achieved by supposing that the longitudinal data arise from a certain nonparametric structural equations model and by making the monotonicity assumption that the effect of exposure on survival agrees in its direction across individuals. A novel weighted analysis involving a consistent estimate of the survival process is shown to produce consistent estimates of SACE. A data illustration is given, and the methods are extended to the context of time-varying exposures. We discuss a sensitivity analysis framework that relaxes assumptions about independent errors in the nonparametric structural equations model and may be used to assess the extent to which inference may be altered by a violation of key identifying assumptions. © 2014 The Authors. Statistics in Medicine published by John Wiley & Sons, Ltd.
Directory of Open Access Journals (Sweden)
G. H. de Rooij
2009-07-01
Full Text Available Current theories for water flow in porous media are valid for scales much smaller than those at which problem of public interest manifest themselves. This provides a drive for upscaled flow equations with their associated upscaled parameters. Upscaling is often achieved through volume averaging, but the solution to the resulting closure problem imposes severe restrictions to the flow conditions that limit the practical applicability. Here, the derivation of a closed expression of the effective hydraulic conductivity is forfeited to circumvent the closure problem. Thus, more limited but practical results can be derived. At the Representative Elementary Volume scale and larger scales, the gravitational potential and fluid pressure are treated as additive potentials. The necessary requirement that the superposition be maintained across scales is combined with conservation of energy during volume integration to establish consistent upscaling equations for the various heads. The power of these upscaling equations is demonstrated by the derivation of upscaled water content-matric head relationships and the resolution of an apparent paradox reported in the literature that is shown to have arisen from a violation of the superposition principle. Applying the upscaling procedure to Darcy's Law leads to the general definition of an upscaled hydraulic conductivity. By examining this definition in detail for porous media with different degrees of heterogeneity, a series of criteria is derived that must be satisfied for Darcy's Law to remain valid at a larger scale.
Atmospheric relative concentrations in building wakes
International Nuclear Information System (INIS)
Ramsdell, J.V. Jr.; Simonen, C.A.; Smyth, S.B.
1995-05-01
This report documents the ARCON95 computer code developed for the U.S. Nuclear Regulatory Commission Office of Nuclear Regulatory Research for use in control room habitability assessments. The document includes a user's guide to the code, a description of the technical basis for the code, and a programmer's guide to the code. The ARCON95 code uses hourly meteorological data and recently developed methods for estimating dispersion in the vicinity of buildings to calculate relative concentrations at control room air intakes that would be exceeded no more five percent of the time. These concentrations are calculated for averaging periods ranging from one hour to 30 days in duration. Relative concentrations calculated by ARCON95 are significantly lower than concentrations calculated using the currently accepted procedure when winds are less than two meters per second. For higher wind speeds, ARCON95 calculates about the same concentrations as the current procedure
Microbes make average 2 nanometer diameter crystalline UO2 particles.
Suzuki, Y.; Kelly, S. D.; Kemner, K. M.; Banfield, J. F.
2001-12-01
It is well known that phylogenetically diverse groups of microorganisms are capable of catalyzing the reduction of highly soluble U(VI) to highly insoluble U(IV), which rapidly precipitates as uraninite (UO2). Because biological uraninite is highly insoluble, microbial uranyl reduction is being intensively studied as the basis for a cost-effective in-situ bioremediation strategy. Previous studies have described UO2 biomineralization products as amorphous or poorly crystalline. The objective of this study is to characterize the nanocrystalline uraninite in detail in order to determine the particle size, crystallinity, and size-related structural characteristics, and to examine the implications of these for reoxidation and transport. In this study, we obtained U-contaminated sediment and water from an inactive U mine and incubated them anaerobically with nutrients to stimulate reductive precipitation of UO2 by indigenous anaerobic bacteria, mainly Gram-positive spore-forming Desulfosporosinus and Clostridium spp. as revealed by RNA-based phylogenetic analysis. Desulfosporosinus sp. was isolated from the sediment and UO2 was precipitated by this isolate from a simple solution that contains only U and electron donors. We characterized UO2 formed in both of the experiments by high resolution-TEM (HRTEM) and X-ray absorption fine structure analysis (XAFS). The results from HRTEM showed that both the pure and the mixed cultures of microorganisms precipitated around 1.5 - 3 nm crystalline UO2 particles. Some particles as small as around 1 nm could be imaged. Rare particles around 10 nm in diameter were also present. Particles adhere to cells and form colloidal aggregates with low fractal dimension. In some cases, coarsening by oriented attachment on \\{111\\} is evident. Our preliminary results from XAFS for the incubated U-contaminated sample also indicated an average diameter of UO2 of 2 nm. In nanoparticles, the U-U distance obtained by XAFS was 0.373 nm, 0.012 nm
Average and local structure of selected metal deuterides
Energy Technology Data Exchange (ETDEWEB)
Soerby, Magnus H.
2005-07-01
deuterides at 1 bar D2 and elevated temperatures (373-573 K) is presented in Paper 1. Deuterium atoms occupy chiefly three types of tetrahedral interstitial sites; two coordinated by 4 Zr atoms and one coordinated by 3 Zr and 1 Ni atoms. The site preference is predominantly ruled by sample composition and less by temperature. On the other hand, the spatial deuterium distribution among the preferred sites is strongly temperature dependant as the long-range correlations break down on heating. The sample is fully decomposed into tetragonal ZrD2 and Zr7Ni10 at 873 K. Th2AlD4 was the only metal deuteride with reported D-D separation substantially below 2 Aa (1.79 Aa) prior to the discovery of RENiInD1.33. However, as being the first ternary deuteride ever studied by PND, the original structure solution was based on very low-resolution data. The present reinvestigation (Paper 2) shows that the site preference was correctly determined, but the deuterium atoms are slightly shifted compared to the earlier report, now yielding acceptable interatomic separations. Solely Th4 tetrahedra are occupied in various Th2Al deuterides. Th8Al4D11 (Th2AlD2.75) takes a superstructure with tripled c-axis due to deuterium ordering. Th2AlD2.3 is disordered and the average distance between partly occupied sites appears as just 1.55 Aa in Rietveld refinements. However, short-range order is expected to prevent D-D distances under 2 Aa. Paper 3 present the first Reverse Monte Carlo (RMC) study of a metal deuteride. RMC is used in combination with total neutron scattering to model short-range deuterium correlations in disordered c-VD0.77. A practically complete blocking of interstitial sites closer than 2 Aa from any occupied deuterium site is observed. The short-range correlations resemble those of the fully ordered low temperature phase c-VD0.75 at length scales up to about 3 Aa, i.e. for the first two coordination spheres. Paper 4 concerns RMC modelling of short-range deuterium correlations in ZrCr2D4
Average and local structure of selected metal deuterides
International Nuclear Information System (INIS)
Soerby, Magnus H.
2004-01-01
elevated temperatures (373-573 K) is presented in Paper 1. Deuterium atoms occupy chiefly three types of tetrahedral interstitial sites; two coordinated by 4 Zr atoms and one coordinated by 3 Zr and 1 Ni atoms. The site preference is predominantly ruled by sample composition and less by temperature. On the other hand, the spatial deuterium distribution among the preferred sites is strongly temperature dependant as the long-range correlations break down on heating. The sample is fully decomposed into tetragonal ZrD2 and Zr7Ni10 at 873 K. Th2AlD4 was the only metal deuteride with reported D-D separation substantially below 2 Aa (1.79 Aa) prior to the discovery of RENiInD1.33. However, as being the first ternary deuteride ever studied by PND, the original structure solution was based on very low-resolution data. The present reinvestigation (Paper 2) shows that the site preference was correctly determined, but the deuterium atoms are slightly shifted compared to the earlier report, now yielding acceptable interatomic separations. Solely Th4 tetrahedra are occupied in various Th2Al deuterides. Th8Al4D11 (Th2AlD2.75) takes a superstructure with tripled c-axis due to deuterium ordering. Th2AlD2.3 is disordered and the average distance between partly occupied sites appears as just 1.55 Aa in Rietveld refinements. However, short-range order is expected to prevent D-D distances under 2 Aa. Paper 3 present the first Reverse Monte Carlo (RMC) study of a metal deuteride. RMC is used in combination with total neutron scattering to model short-range deuterium correlations in disordered c-VD0.77. A practically complete blocking of interstitial sites closer than 2 Aa from any occupied deuterium site is observed. The short-range correlations resemble those of the fully ordered low temperature phase c-VD0.75 at length scales up to about 3 Aa, i.e. for the first two coordination spheres. Paper 4 concerns RMC modelling of short-range deuterium correlations in ZrCr2D4 at ambient and low
Chaotic Universe, Friedmannian on the average. Pt. 2
Energy Technology Data Exchange (ETDEWEB)
Marochnik, L S [Rostovskij-na-Donu Gosudarstvennyj Univ. (USSR). Astrofizicheskoe Otdelenie
1980-05-01
On the basis of the solutions obtained in the previous paper, the changes in the scenario of the standard model of the Big Bang are found. The chaos degree (constraints on fluctuation spectra) is obtained, which could be still preserved by the initially completely chaotic Universe at the time of light elements nucleosynthesis tsub(es). The time boundaries of hadron and lepton eras and the time the electron neutrinos and neutrons become 'frozen' in reactions of weak interaction may be shifted up to 1.4 times. The corresponding temperatures may shift off from the standard ones 0.88 times if the mean-square level of fluctuations is close to unity. If the density of the energy of fluctuations concentrated in the short-wave region of the spectrum is less than 1.5 epsilon, the nucleosynthesis leads to a helium abundance coinciding with the observed one. If at the time tsub(es) the maximum of the spectral density of the energy is in the long-wave region, that is lambdasub(max) >>ctsub(es) the level of the chaos during the period of nucleosynthesis is restricted to ..nu.. approx. < 1.76 (where ..nu.. approx. ..integral../Csub(K)//sup 2/d/sup 3/K, Csub(K) is Fourier component of the amplitude of metric fluctuations). In particular, the protogalactic vortical disturbances with a wide spectrum ..delta.. approx. > 4 x 10/sup 3/ ..cap omega../sup -1/(..delta.. = ..delta.. K/K, ..cap omega.. = rho/rhosub(crit)) are compatible with the observed helium abundance.
Forecasting of Average Monthly River Flows in Colombia
Mesa, O. J.; Poveda, G.
2006-05-01
The last two decades have witnessed a marked increase in our knowledge of the causes of interannual hydroclimatic variability and our ability to make predictions. Colombia, located near the seat of the ENSO phenomenon, has been shown to experience negative (positive) anomalies in precipitation in concert with El Niño (La Niña). In general besides the Pacific Ocean, Colombia has climatic influences from the Atlantic Ocean and the Caribbean Sea through the tropical forest of the Amazon basin and the savannas of the Orinoco River, in top of the orographic and hydro-climatic effects introduced by the Andes. As in various other countries of the region, hydro-electric power contributes a large proportion (75 %) of the total electricity generation in Colombia. Also, most agriculture is rain-fed dependant, and domestic water supply relies mainly on surface waters from creeks and rivers. Besides, various vector borne tropical diseases intensify in response to rain and temperature changes. Therefore, there is a direct connection between climatic fluctuations and national and regional economies. This talk specifically presents different forecasts of average monthly stream flows for the inflow into the largest reservoir used for hydropower generation in Colombia, and illustrates the potential economic savings of such forecasts. Because of planning of the reservoir operation, the most appropriated time scale for this application is the annual to interannual. Fortunately, this corresponds to the scale at which hydroclimate variability understanding has improved significantly. Among the different possibilities we have explored: traditional statistical ARIMA models, multiple linear regression, natural and constructed analogue models, the linear inverse model, neural network models, the non-parametric regression splines (MARS) model, regime dependant Markovian models and one we termed PREBEO, which is based on spectral bands decomposition using wavelets. Most of the methods make
Arsenic concentrations in Chinese coals
International Nuclear Information System (INIS)
Wang Mingshi; Zheng Baoshan; Wang Binbin; Li Shehong; Wu Daishe; Hu Jun
2006-01-01
The arsenic concentrations in 297 coal samples were collected from the main coal-mines of 26 provinces in China were determined by molybdenum blue coloration method. These samples were collected from coals that vary widely in coal rank and coal-forming periods from the five main coal-bearing regions in China. Arsenic content in Chinese coals range between 0.24 to 71 mg/kg. The mean of the concentration of Arsenic is 6.4 ± 0.5 mg/kg and the geometric mean is 4.0 ± 8.5 mg/kg. The level of arsenic in China is higher in northeastern and southern provinces, but lower in northwestern provinces. The relationship between arsenic content and coal-forming period, coal rank is studied. It was observed that the arsenic contents decreases with coal rank in the order: Tertiary > Early Jurassic > Late Triassic > Late Jurassic > Middle Jurassic > Late Permian > Early Carboniferous > Middle Carboniferous > Late Carboniferous > Early Permian; It was also noted that the arsenic contents decrease in the order: Subbituminous > Anthracite > Bituminous. However, compared with the geological characteristics of coal forming region, coal rank and coal-forming period have little effect on the concentration of arsenic in Chinese coal. The average arsenic concentration of Chinese coal is lower than that of the whole world. The health problems in China derived from in coal (arsenism) are due largely to poor local life-style practices in cooking and home heating with coal rather than to high arsenic contents in the coal
Acker, James G.; Uz, Stephanie Schollaert; Shen, Suhung; Leptoukh, Gregory G.
2010-01-01
Application of appropriate spatial averaging techniques is crucial to correct evaluation of ocean color radiometric data, due to the common log-normal or mixed log-normal distribution of these data. Averaging method is particularly crucial for data acquired in coastal regions. The effect of averaging method was markedly demonstrated for a precipitation-driven event on the U.S. Northeast coast in October-November 2005, which resulted in export of high concentrations of riverine colored dissolved organic matter (CDOM) to New York and New Jersey coastal waters over a period of several days. Use of the arithmetic mean averaging method created an inaccurate representation of the magnitude of this event in SeaWiFS global mapped chl a data, causing it to be visualized as a very large chl a anomaly. The apparent chl a anomaly was enhanced by the known incomplete discrimination of CDOM and phytoplankton chlorophyll in SeaWiFS data; other data sources enable an improved characterization. Analysis using the geometric mean averaging method did not indicate this event to be statistically anomalous. Our results predicate the necessity of providing the geometric mean averaging method for ocean color radiometric data in the Goddard Earth Sciences DISC Interactive Online Visualization ANd aNalysis Infrastructure (Giovanni).
Pinheiro, Samya de Lara Lins de Araujo; Saldiva, Paulo Hilário Nascimento; Schwartz, Joel; Zanobetti, Antonella
2014-12-01
OBJECTIVE To analyze the effect of air pollution and temperature on mortality due to cardiovascular and respiratory diseases. METHODS We evaluated the isolated and synergistic effects of temperature and particulate matter with aerodynamic diameter mortality of individuals > 40 years old due to cardiovascular disease and that of individuals > 60 years old due to respiratory diseases in Sao Paulo, SP, Southeastern Brazil, between 1998 and 2008. Three methodologies were used to evaluate the isolated association: time-series analysis using Poisson regression model, bidirectional case-crossover analysis matched by period, and case-crossover analysis matched by the confounding factor, i.e., average temperature or pollutant concentration. The graphical representation of the response surface, generated by the interaction term between these factors added to the Poisson regression model, was interpreted to evaluate the synergistic effect of the risk factors. RESULTS No differences were observed between the results of the case-crossover and time-series analyses. The percentage change in the relative risk of cardiovascular and respiratory mortality was 0.85% (0.45;1.25) and 1.60% (0.74;2.46), respectively, due to an increase of 10 μg/m3 in the PM10 concentration. The pattern of correlation of the temperature with cardiovascular mortality was U-shaped and that with respiratory mortality was J-shaped, indicating an increased relative risk at high temperatures. The values for the interaction term indicated a higher relative risk for cardiovascular and respiratory mortalities at low temperatures and high temperatures, respectively, when the pollution levels reached approximately 60 μg/m3. CONCLUSIONS The positive association standardized in the Poisson regression model for pollutant concentration is not confounded by temperature, and the effect of temperature is not confounded by the pollutant levels in the time-series analysis. The simultaneous exposure to different levels of
Directory of Open Access Journals (Sweden)
Samya de Lara Lins de Araujo Pinheiro
2014-12-01
Full Text Available OBJECTIVE To analyze the effect of air pollution and temperature on mortality due to cardiovascular and respiratory diseases. METHODS We evaluated the isolated and synergistic effects of temperature and particulate matter with aerodynamic diameter 40 years old due to cardiovascular disease and that of individuals > 60 years old due to respiratory diseases in Sao Paulo, SP, Southeastern Brazil, between 1998 and 2008. Three methodologies were used to evaluate the isolated association: time-series analysis using Poisson regression model, bidirectional case-crossover analysis matched by period, and case-crossover analysis matched by the confounding factor, i.e., average temperature or pollutant concentration. The graphical representation of the response surface, generated by the interaction term between these factors added to the Poisson regression model, was interpreted to evaluate the synergistic effect of the risk factors. RESULTS No differences were observed between the results of the case-crossover and time-series analyses. The percentage change in the relative risk of cardiovascular and respiratory mortality was 0.85% (0.45;1.25 and 1.60% (0.74;2.46, respectively, due to an increase of 10 μg/m3 in the PM10 concentration. The pattern of correlation of the temperature with cardiovascular mortality was U-shaped and that with respiratory mortality was J-shaped, indicating an increased relative risk at high temperatures. The values for the interaction term indicated a higher relative risk for cardiovascular and respiratory mortalities at low temperatures and high temperatures, respectively, when the pollution levels reached approximately 60 μg/m3. CONCLUSIONS The positive association standardized in the Poisson regression model for pollutant concentration is not confounded by temperature, and the effect of temperature is not confounded by the pollutant levels in the time-series analysis. The simultaneous exposure to different levels of
Forecasting ozone concentrations in the east of Croatia using ...
Indian Academy of Sciences (India)
for urban and another one for rural area in the eastern part of Croatia. ... 2010). Apart from the negative impact on respiratory system, atmo- ..... Figure 3. Daily average ozone concentrations in the rural (Tikveš) and urban (Osijek) areas.
Underscreening in concentrated electrolytes.
Lee, Alpha A; Perez-Martinez, Carla S; Smith, Alexander M; Perkin, Susan
2017-07-01
Screening of a surface charge by an electrolyte and the resulting interaction energy between charged objects is of fundamental importance in scenarios from bio-molecular interactions to energy storage. The conventional wisdom is that the interaction energy decays exponentially with object separation and the decay length is a decreasing function of ion concentration; the interaction is thus negligible in a concentrated electrolyte. Contrary to this conventional wisdom, we have shown by surface force measurements that the decay length is an increasing function of ion concentration and Bjerrum length for concentrated electrolytes. In this paper we report surface force measurements to test directly the scaling of the screening length with Bjerrum length. Furthermore, we identify a relationship between the concentration dependence of this screening length and empirical measurements of activity coefficient and differential capacitance. The dependence of the screening length on the ion concentration and the Bjerrum length can be explained by a simple scaling conjecture based on the physical intuition that solvent molecules, rather than ions, are charge carriers in a concentrated electrolyte.
Concentrating photovoltaic solar panel
Cashion, Steven A; Bowser, Michael R; Farrelly, Mark B; Hines, Braden E; Holmes, Howard C; Johnson, Jr., Richard L; Russell, Richard J; Turk, Michael F
2014-04-15
The present invention relates to photovoltaic power systems, photovoltaic concentrator modules, and related methods. In particular, the present invention features concentrator modules having interior points of attachment for an articulating mechanism and/or an articulating mechanism that has a unique arrangement of chassis members so as to isolate bending, etc. from being transferred among the chassis members. The present invention also features adjustable solar panel mounting features and/or mounting features with two or more degrees of freedom. The present invention also features a mechanical fastener for secondary optics in a concentrator module.
Photovoltaic static concentrator analysis
Almonacid, G.; Luque, A.; Molledo, A. G.
1984-12-01
Ray tracing is the basis of the present analysis of truncated bifacial compound parabolic concentrators filled with a dielectric substance, which are of interest in photovoltaic applications where the bifacial cells allow higher static concentrations to be achieved. Among the figures of merit for this type of concentrator, the directional intercept factor plays a major role and is defined as the ratio of the power of the collector to that at the entry aperture, in a lossless concentrator illuminated by light arriving from a given direction. A procedure for measuring outdoor, full size panels has been developed, and a correction method for avoiding the effect of unwanted diffuse radiation during the measurements is presented.