WorldWideScience

Sample records for time stamp support

  1. Authentication, Time-Stamping and Digital Signatures

    Science.gov (United States)

    Levine, Judah

    1996-01-01

    Time and frequency data are often transmitted over public packet-switched networks, and the use of this mode of distribution is likely to increase in the near future as high-speed logical circuits transmitted via networks replace point-to-point physical circuits. ALthough these networks have many technical advantages, they are susceptible to evesdropping, spoofing, and the alteration of messages enroute using techniques that are relatively simple to implement and quite difficult to detect. I will discuss a number of solutions to these problems, including the authentication mechanism used in the Network Time Protocol (NTP) and the more general technique of signing time-stamps using public key cryptography. This public key method can also be used to implement the digital analog of a Notary Public, and I will discuss how such a system could be realized on a public network such as the Internet.

  2. Time Stamp Synchronization of PEFP Distributed Control Systems

    International Nuclear Information System (INIS)

    Song, Young Gi; An, Eun Mi; Kwon, Hyeok Jung; Cho, Yong Sub

    2010-01-01

    Proton Engineering Frontier Project (PEFP) proton linac consists of several types of control systems, such as soft Input Output Controllers (IOC) and embedded IOC based on Experimental Physics Industrial Control System (EPICS) for each subsection of PEFP facility. One of the important factors is that IOC's time clock is synchronized. The synchronized time and time stamp can be achieved with Network Time Protocol (NTP) and EPICS time stamp record without timing hardware. The requirement of the time accuracy of IOCs is less than 1 second. The main objective of this study is to configure a master clock and produce Process Variable (PV) time stamps using local CPU time synchronized from the master clock. The distributed control systems are attached on PEFP control network

  3. Digital time stamping system based on open source technologies.

    Science.gov (United States)

    Miskinis, Rimantas; Smirnov, Dmitrij; Urba, Emilis; Burokas, Andrius; Malysko, Bogdan; Laud, Peeter; Zuliani, Francesco

    2010-03-01

    A digital time stamping system based on open source technologies (LINUX-UBUNTU, OpenTSA, OpenSSL, MySQL) is described in detail, including all important testing results. The system, called BALTICTIME, was developed under a project sponsored by the European Commission under the Program FP 6. It was designed to meet the requirements posed to the systems of legal and accountable time stamping and to be applicable to the hardware commonly used by the national time metrology laboratories. The BALTICTIME system is intended for the use of governmental and other institutions as well as personal bodies. Testing results demonstrate that the time stamps issued to the user by BALTICTIME and saved in BALTICTIME's archives (which implies that the time stamps are accountable) meet all the regulatory requirements. Moreover, the BALTICTIME in its present implementation is able to issue more than 10 digital time stamps per second. The system can be enhanced if needed. The test version of the BALTICTIME service is free and available at http://baltictime. pfi.lt:8080/btws/ and http://baltictime.lnmc.lv:8080/btws/.

  4. Extracting Hot spots of Topics from Time Stamped Documents

    Science.gov (United States)

    Chen, Wei; Chundi, Parvathi

    2011-01-01

    Identifying time periods with a burst of activities related to a topic has been an important problem in analyzing time-stamped documents. In this paper, we propose an approach to extract a hot spot of a given topic in a time-stamped document set. Topics can be basic, containing a simple list of keywords, or complex. Logical relationships such as and, or, and not are used to build complex topics from basic topics. A concept of presence measure of a topic based on fuzzy set theory is introduced to compute the amount of information related to the topic in the document set. Each interval in the time period of the document set is associated with a numeric value which we call the discrepancy score. A high discrepancy score indicates that the documents in the time interval are more focused on the topic than those outside of the time interval. A hot spot of a given topic is defined as a time interval with the highest discrepancy score. We first describe a naive implementation for extracting hot spots. We then construct an algorithm called EHE (Efficient Hot Spot Extraction) using several efficient strategies to improve performance. We also introduce the notion of a topic DAG to facilitate an efficient computation of presence measures of complex topics. The proposed approach is illustrated by several experiments on a subset of the TDT-Pilot Corpus and DBLP conference data set. The experiments show that the proposed EHE algorithm significantly outperforms the naive one, and the extracted hot spots of given topics are meaningful. PMID:21765568

  5. Time-stamping system for nuclear physics experiments at RIKEN RIBF

    International Nuclear Information System (INIS)

    Baba, H.; Ichihara, T.; Ohnishi, T.; Takeuchi, S.; Yoshida, K.; Watanabe, Y.; Ota, S.; Shimoura, S.; Yoshinaga, K.

    2015-01-01

    A time-stamping system for nuclear physics experiments has been introduced at the RIKEN Radioactive Isotope Beam Factory. Individual trigger signals can be applied for separate data acquisition (DAQ) systems. After the measurements are complete, separately taken data are merged based on the time-stamp information. In a typical experiment, coincidence trigger signals are formed from multiple detectors to take desired events only. The time-stamping system allows the use of minimum bias triggers. Since coincidence conditions are given by software, a variety of physics events can be flexibly identified. The live time for a DAQ system is important when attempting to determine reaction cross-sections. However, the combined live time for separate DAQ systems is not clearly known because it depends not only on the DAQ dead time but also on the coincidence conditions. Using the proposed time-stamping system, all trigger timings can be acquired, so that the combined live time can be easily determined. The combined live time is also estimated using Monte Carlo simulations, and the results are compared with the directly measured values in order to assess the accuracy of the simulation

  6. Impact of Electronic Signatures and Time Stamping for the Protection of Electronic Agreements

    Directory of Open Access Journals (Sweden)

    Tadas Limba

    2012-12-01

    Full Text Available The article e495 valuates the impact of e-signatures and time stamping on electronic contracts and electronic documents for performing e-business opportunities and goals, and analyses e-signature application for business cases. Various electronic services, virtual shopping, electronic cash transactions are becoming increasingly popular as they allow users to quickly perform different actions, operations and functions. It is important not only for convenience, but also to ensure consumer data security and reliability. Security reasons are not enough for security transmitted data, since this method does not allow clarification of information about sender identity.Use of electronic signatures, electronic identities, checgs and ensures a very high level of data security in interchange data processes. E-signature allows e-business companies to transfer the company’s operation business processes and their application to the organization and management in the electronic environment, also automate internal and external compans processes, includinggon-going business processes.The object of paper is .-signature and time stamping application in the theoretical and practical way.The goal of this paper while evaluating and estimating the .-signature and time stamping application, i’s regulation and legal implementation worldwidesand in Lithuania—is to provideluseful recommendations for more efficient impact developing -commerce and -business in situations when -signature and time stamping is used for ensuring electronic contracs security.

  7. Impact of Electronic Signatures and Time Stamping for the Protection of Electronic Agreements

    Directory of Open Access Journals (Sweden)

    Tadas Limba

    2013-02-01

    Full Text Available The article e495 valuates the impact of e-signatures and time stamping on electronic contracts and electronic documents for performing e-business opportunities and goals, and analyses e-signature application for business cases. Various electronic services, virtual shopping, electronic cash transactions are becoming increasingly popular as they allow users to quickly perform different actions, operations and functions. It is important not only for convenience, but also to ensure consumer data security and reliability. Security reasons are not enough for security transmitted data, since this method does not allow clarification of information about sender identity. Use of electronic signatures, electronic identities, checgs and ensures a very high level of data security in interchange data processes. E-signature allows e-business companies to transfer the company’s operation business processes and their application to the organization and management in the electronic environment, also automate internal and external compans processes, includinggon-going business processes. The object of paper is .-signature and time stamping application in the theoretical and practical way. The goal of this paper while evaluating and estimating the .-signature and time stamping application, i’s regulation and legal implementation worldwidesand in Lithuania—is to provideluseful recommendations for more efficient impact developing -commerce and -business in situations when -signature and time stamping is used for ensuring electronic contracs security.

  8. Time-stamp correction of magnetic observatory data acquired during unavailability of time-synchronization services

    Science.gov (United States)

    Coïsson, Pierdavide; Telali, Kader; Heumez, Benoit; Lesur, Vincent; Lalanne, Xavier; Jiang Xin, Chang

    2017-09-01

    During magnetic observatory data acquisition, the data time stamp is kept synchronized with a precise source of time. This is usually done using a GPS-controlled pulse per second (PPS) signal. For some observatories located in remote areas or where internet restrictions are enforced, only the magnetometer data are transmitted, limiting the capabilities of monitoring the acquisition operations. The magnetic observatory in Lanzhou (LZH), China, experienced an unnoticed interruption of the GPS PPS starting 7 March 2013. The data logger clock drifted slowly in time: in 6 months a lag of 27 s was accumulated. After a reboot on 2 April 2014 the drift became faster, -2 s per day, before the GPS PPS could be restored on 8 July 2014. To estimate the time lags that LZH time series had accumulated, we compared it with data from other observatories located in East Asia. A synchronization algorithm was developed. Natural sources providing synchronous events could be used as markers to obtain the time lag between the observatories. The analysis of slices of 1 h of 1 s data at arbitrary UTC allowed estimating time lags with an uncertainty of ˜ 11 s, revealing the correct trends of LZH time drift. A precise estimation of the time lag was obtained by comparing data from co-located instruments controlled by an independent PPS. In this case, it was possible to take advantage of spikes and local noise that constituted precise time markers. It was therefore possible to determine a correction to apply to LZH time stamps to correct the data files and produce reliable 1 min averaged definitive magnetic data.

  9. Time stamp technique using a nuclear emulsion multi-stage shifter for gamma-ray telescope

    International Nuclear Information System (INIS)

    Takahashi, Satoru; Aoki, Shigeki; Rokujo, Hiroki; Hamada, Kaname; Komatsu, Masahiro; Morishima, Kunihiro; Nakamura, Mitsuhiro; Nakano, Toshiyuki; Niwa, Kimio; Sato, Osamu; Yoshioka, Teppei; Kodama, Koichi

    2010-01-01

    Nuclear emulsion has a potential use as a gamma-ray telescope with high angular resolution. For this application it is necessary to know the time when each track was recorded in the emulsion. In previous experiments using nuclear emulsion, various efforts were used to associate time to nuclear emulsion tracks and to improve the time resolution. Using a high speed readout system for nuclear emulsion together with a clock-based multi-stage emulsion shifter, we invented a technique to give a time-stamp to emulsion tracks and greatly improve the time resolution. A test experiment with a 2-stage shifter was used to demonstrate the principle of multi-stage shifting, and we achieved a time resolution 1.5 s for 12.1 h (about 1 part in 29 000) with the time stamp reliability 97% and the time stamp efficiency 98%. This multi-stage shifter can achieve the time resolution required for a gamma-ray telescope and can also be applied to another cosmic ray observations and accelerator experiments using nuclear emulsion.

  10. Nanosecond Level UTC Timing Generation and Stamping in CERN's LHC

    CERN Document Server

    Alvarez, P; Lewis, J; Serrano, J

    2003-01-01

    The General Machine Timing (GMT) at CERN uses an RS-485 multi-drop network through which messages are broadcast by a Central Timing Generator (CTG) module at a rate of 500 kb/s and decoded by many receiver modules in different form factors. For long distance transmission, optical fibers are used. As a result of cabling and capacitive loading of the receivers' inputs, the timing message signal presents an average jitter of 14 ns at any receiver input. For the LHC era, the 500 kb/s rate will be maintained to ensure compatibility with old receivers. However, a special kind of Phase Locked Loop (PLL), involving digital control in a Field Programmable Gate Array (FPGA) and a DAC to control a Voltage Controlled Crystal Oscillator (VCXO), has been developed to generate a 40 MHz square wave at the receiving side which is locked on average to the timing message signal but presents a jitter of less than 1 ns. This 40 MHz signal is locked to UTC because the encoder in the CTG card uses a 40 MHz clock coming from a GPS r...

  11. Time stamp generation with inverse FIR filters for Positron Emission Tomography

    International Nuclear Information System (INIS)

    Namias, Mauro

    2009-01-01

    Photon coincidence detection is the process by which Positron Emission Tomography (PET) works. This requires the determination of the time of impact of each coincident photon at the detector system, also known as time stamp. In this work, the timestamp was generated by means of digital time-domain deconvolution with FIR filters for a INa(Tl) based system. The detector deadtime was reduced from 350 ns to 175 ns while preserving the system's energy resolution and a direct relation between the amount of light collected and the temporal resolution was found.(author)

  12. Stamp in honour of CERN

    CERN Multimedia

    1966-01-01

    21 February 1966. The Swiss post office issued a stamp in CERN's honour. This stamp showed the flags of the thirteen Member States at the time arranged in the geometrical outline of Switzerland against a background of a track photograph.

  13. Recognition of Time Stamps on Full-Disk Hα Images Using Machine Learning Methods

    Science.gov (United States)

    Xu, Y.; Huang, N.; Jing, J.; Liu, C.; Wang, H.; Fu, G.

    2016-12-01

    Observation and understanding of the physics of the 11-year solar activity cycle and 22-year magnetic cycle are among the most important research topics in solar physics. The solar cycle is responsible for magnetic field and particle fluctuation in the near-earth environment that have been found increasingly important in affecting the living of human beings in the modern era. A systematic study of large-scale solar activities, as made possible by our rich data archive, will further help us to understand the global-scale magnetic fields that are closely related to solar cycles. The long-time-span data archive includes both full-disk and high-resolution Hα images. Prior to the widely use of CCD cameras in 1990s, 35-mm films were the major media to store images. The research group at NJIT recently finished the digitization of film data obtained by the National Solar Observatory (NSO) and Big Bear Solar Observatory (BBSO) covering the period of 1953 to 2000. The total volume of data exceeds 60 TB. To make this huge database scientific valuable, some processing and calibration are required. One of the most important steps is to read the time stamps on all of the 14 million images, which is almost impossible to be done manually. We implemented three different methods to recognize the time stamps automatically, including Optical Character Recognition (OCR), Classification Tree and TensorFlow. The latter two are known as machine learning algorithms which are very popular now a day in pattern recognition area. We will present some sample images and the results of clock recognition from all three methods.

  14. Construction of Time-Stamped Mobility Map for Path Tracking via Smith-Waterman Measurement Matching

    Directory of Open Access Journals (Sweden)

    Mu Zhou

    2014-01-01

    Full Text Available Path tracking in wireless and mobile environments is a fundamental technology for ubiquitous location-based services (LBSs. In particular, it is very challenging to develop highly accurate and cost-efficient tracking systems applied to the anonymous areas where the floor plans are not available for security and privacy reasons. This paper proposes a novel path tracking approach for large Wi-Fi areas based on the time-stamped unlabeled mobility map which is constructed from Smith-Waterman received signal strength (RSS measurement matching. Instead of conventional location fingerprinting, we construct mobility map with the technique of dimension reduction from the raw measurement space into a low-dimensional embedded manifold. The feasibility of our proposed approach is verified by the real-world experiments in the HKUST campus Wi-Fi networks, sMobileNet. The experimental results prove that our approach is adaptive and capable of achieving an adequate precision level in path tracking.

  15. Design and implementation of a nanosecond time-stamping readout system-on-chip for photo-detectors

    International Nuclear Information System (INIS)

    Anvar, Shebli; Château, Frédéric; Le Provost, Hervé; Louis, Frédéric; Manolopoulos, Konstantinos; Moudden, Yassir; Vallage, Bertrand; Zonca, Eric

    2014-01-01

    A readout system suitable for a large number of synchronized photo-detection units has been designed. Each unit embeds a specifically designed fully integrated communicating system based on Xilinx FPGA SoC technology. It runs the VxWorks real-time OS and a custom data acquisition software designed within the Ice middleware framework, resulting in a highly flexible, controllable and scalable distributed application. Clock distribution and delay calibration over customized fixed latency gigabit Ethernet links enable synchronous time-stamping of events with nanosecond precision. The implementation of this readout system on several data-collecting units as well as its performances are described

  16. A general dead-time correction method based on live-time stamping. Application to the measurement of short-lived radionuclides.

    Science.gov (United States)

    Chauvenet, B; Bobin, C; Bouchard, J

    2017-12-01

    Dead-time correction formulae are established in the general case of superimposed non-homogeneous Poisson processes. Based on the same principles as conventional live-timed counting, this method exploits the additional information made available using digital signal processing systems, and especially the possibility to store the time stamps of live-time intervals. No approximation needs to be made to obtain those formulae. Estimates of the variances of corrected rates are also presented. This method is applied to the activity measurement of short-lived radionuclides. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Vertically integrated deep N-well CMOS MAPS with sparsification and time stamping capabilities for thin charged particle trackers

    International Nuclear Information System (INIS)

    Ratti, L.; Gaioni, L.; Manghisoni, M.; Re, V.; Traversi, G.

    2010-01-01

    A fine pitch, deep N-well CMOS monolithic active pixel sensor (DNW CMOS MAPS) with sparsified readout architecture and time stamping capabilities has been designed in a vertical integration (3D) technology. In this process, two 130 nm CMOS wafers are face-to-face bonded by means of thermo-compression techniques ensuring both the mechanical stability of the structure and the electrical interconnection between circuits belonging to different layers. This 3D design represents the evolution of a DNW monolithic sensor already fabricated in a planar 130 nm CMOS technology in view of applications to the vertex detector of the International Linear Collider (ILC). The paper is devoted to discussing the main design features and expected performance of the 3D DNW MAPS. Besides describing the front-end circuits and the general architecture of the detector, the work also provides some results from calculations and Monte Carlo device simulations comparing the old 2D solution with the new 3D one and illustrating the attainable detection efficiency improvements.

  18. Vertically integrated deep N-well CMOS MAPS with sparsification and time stamping capabilities for thin charged particle trackers

    Energy Technology Data Exchange (ETDEWEB)

    Ratti, L., E-mail: lodovico.ratti@unipv.i [Universita di Pavia, Dipartimento di Elettronica, Via Ferrata 1, I-27100 Pavia (Italy); INFN, Sezione di Pavia, Via Bassi 6, I-27100 Pavia (Italy); Gaioni, L. [Universita di Pavia, Dipartimento di Elettronica, Via Ferrata 1, I-27100 Pavia (Italy); INFN, Sezione di Pavia, Via Bassi 6, I-27100 Pavia (Italy); Manghisoni, M.; Re, V.; Traversi, G. [Universita di Bergamo, Dipartimento di Ingegneria Industriale, Via Marconi 5, I-24044 Dalmine (Bulgaria) (Italy); INFN, Sezione di Pavia, Via Bassi 6, I-27100 Pavia (Italy)

    2010-12-11

    A fine pitch, deep N-well CMOS monolithic active pixel sensor (DNW CMOS MAPS) with sparsified readout architecture and time stamping capabilities has been designed in a vertical integration (3D) technology. In this process, two 130 nm CMOS wafers are face-to-face bonded by means of thermo-compression techniques ensuring both the mechanical stability of the structure and the electrical interconnection between circuits belonging to different layers. This 3D design represents the evolution of a DNW monolithic sensor already fabricated in a planar 130 nm CMOS technology in view of applications to the vertex detector of the International Linear Collider (ILC). The paper is devoted to discussing the main design features and expected performance of the 3D DNW MAPS. Besides describing the front-end circuits and the general architecture of the detector, the work also provides some results from calculations and Monte Carlo device simulations comparing the old 2D solution with the new 3D one and illustrating the attainable detection efficiency improvements.

  19. A new approach for improved time and position measurements for TOF-PET: Time-stamping of the photo-electrons using analogue SiPMs

    Energy Technology Data Exchange (ETDEWEB)

    Doroud, K., E-mail: Katayoun.Doroud@cern.ch [CERN Geneva (Switzerland); Williams, M.C.S. [CERN Geneva (Switzerland); INFN, Bologna (Italy)

    2017-03-21

    Measurement of the Time-of-Flight (TOF) of the 511 keV gammas brings an important reduction of statistical noise in the PET image, with higher precision time measurements producing clearer images. The common method of coupling a photodetector to scintillating crystals is to have two matching matrices, with a one-to-one coupling between the crystal and the photodetector. We propose a new geometry based on analogue strip SiPMs reading out a scintillator cut into slabs. This technique allows the time stamping of individual photo-electrons and extracts the best time resolution using a specific algorithm. Here we present the results from the first ‘slab module’ test.

  20. A new approach for improved time and position measurements for TOF-PET: Time-stamping of the photo-electrons using analogue SiPMs

    CERN Document Server

    Doroud, K

    2017-01-01

    Measurement of the Time-of-Flight (TOF) of the 511 keV gammas brings an important reduction of statistical noise in the PET image, with higher precision time measurements producing clearer images. The common method of coupling a photodetector to scintillating crystals is to have two matching matrices, with a one-to-one coupling between the crystal and the photodetector. We propose a new geometry based on analogue strip SiPMs reading out a scintillator cut into slabs. This technique allows the time stamping of individual photo-electrons and extracts the best time resolution using a specific algorithm. Here we present the results from the first ‘slab module’ test.

  1. ANCIENT BREAD STAMPS FROM JORDAN

    OpenAIRE

    Kakish, Randa

    2014-01-01

    Marking bread was an old practice performed in different parts of the old world. It was done for religious, magical, economic and identification purposes. Bread stamps differ from other groups of stamps. Accordingly, the aim of this article is to identify such stamps, displayed or stored, in a number of Jordanian Archaeological Museums. A col-lection of twelve ancient bread stamps were identified and studied. Two of the stamps were of unknown provenance while the others came from al-Shuneh, D...

  2. Comparison between Laser and Stamping without Die (SWD for Micro Tapered Hole Forming

    Directory of Open Access Journals (Sweden)

    Yung-Chou Hung

    2016-03-01

    Full Text Available The forming of a micro tapered hole is based on nanosecond pulsed laser processing, which conforms to fast processing time and high throughput; however, the microhole quality should be improved. Micro stamping is a technology providing high precise size and speed. The greatest difficulty in forming a microhole by micro stamping is the precision alignment of the punch head to the lower die. In order to overcome the difficulty, we proposed a concept of stamping without die (SWD. Without a lower die, the tapered punch head was directly applied to the workpiece for micro stamping, and a thicker workpiece surrounding the punching area provides a better support to the stamping process. Thus, a successful forming of micro tapered holes is completed. The micro tapered hole depth is 300 μm, and the maximum ratio of inlet to outlet diameter is 18:1. In order to reduce the number of experiments, the finite element analysis software DEFORM-3D was used for forming analysis. The simulation forecast result was compared with the experimental processing, which was well validated. Under different experimental parameters of laser energy and defocusing distance, drilling results by two methods show that the microhole quality by stamping process is better than by laser processing.

  3. Evolutions of Advanced Stamping CAE -- Technology Adventures and Business Impact on Automotive Dies and Stamping

    International Nuclear Information System (INIS)

    Wang Chuantao

    2005-01-01

    In the past decade, sheet metal forming and die development has been transformed to a science-based and technology-driven engineering and manufacturing enterprise from a tryout-based craft. Stamping CAE, especially the sheet metal forming simulation, as one of the core components in digital die making and digital stamping, has played a key role in this historical transition. The stamping simulation technology and its industrial applications have greatly impacted automotive sheet metal product design, die developments, die construction and tryout, and production stamping. The stamping CAE community has successfully resolved the traditional formability problems such as splits and wrinkles. The evolution of the stamping CAE technology and business demands opens even greater opportunities and challenges to stamping CAE community in the areas of (1) continuously improving simulation accuracy, drastically reducing simulation time-in-system, and improving operationalability (friendliness) (2) resolving those historically difficult-to-resolve problems such as dimensional quality problems (springback and twist) and surface quality problems (distortion and skid/impact lines) (3) resolving total manufacturability problems in line die operations including blanking, draw/redraw, trim/piercing, and flanging, and (4) overcoming new problems in forming new sheet materials with new forming techniques. In this article, the author first provides an overview of the stamping CAE technology adventures and achievements, and industrial applications in the past decade. Then the author presents a summary of increasing manufacturability needs from the formability to total quality and total manufacturability of sheet metal stampings. Finally, the paper outlines the new needs and trends for continuous improvements and innovations to meet increasing challenges in line die formability and quality requirements in automotive stamping

  4. Evolutions of Advanced Stamping CAE — Technology Adventures and Business Impact on Automotive Dies and Stamping

    Science.gov (United States)

    Wang, Chuantao (C. T.)

    2005-08-01

    In the past decade, sheet metal forming and die development has been transformed to a science-based and technology-driven engineering and manufacturing enterprise from a tryout-based craft. Stamping CAE, especially the sheet metal forming simulation, as one of the core components in digital die making and digital stamping, has played a key role in this historical transition. The stamping simulation technology and its industrial applications have greatly impacted automotive sheet metal product design, die developments, die construction and tryout, and production stamping. The stamping CAE community has successfully resolved the traditional formability problems such as splits and wrinkles. The evolution of the stamping CAE technology and business demands opens even greater opportunities and challenges to stamping CAE community in the areas of (1) continuously improving simulation accuracy, drastically reducing simulation time-in-system, and improving operationalability (friendliness), (2) resolving those historically difficult-to-resolve problems such as dimensional quality problems (springback and twist) and surface quality problems (distortion and skid/impact lines), (3) resolving total manufacturability problems in line die operations including blanking, draw/redraw, trim/piercing, and flanging, and (4) overcoming new problems in forming new sheet materials with new forming techniques. In this article, the author first provides an overview of the stamping CAE technology adventures and achievements, and industrial applications in the past decade. Then the author presents a summary of increasing manufacturability needs from the formability to total quality and total manufacturability of sheet metal stampings. Finally, the paper outlines the new needs and trends for continuous improvements and innovations to meet increasing challenges in line die formability and quality requirements in automotive stamping.

  5. Stamping through astronomy

    CERN Document Server

    Dicati, Renato

    2013-01-01

    Stamps and other postal documents are an attractive vehicle for presenting astronomy and its development. Written with expertise and great enthusiasm, this unique book offers a historical and philatelic survey of astronomy and some related topics on space exploration. It contains more than 1300 color reproductions of stamps relating to the history of astronomy, ranging from the earliest observations of the sky to modern research conducted with satellites and space probes. Featured are the astronomers and astrophysicists who contributed to this marvelous story – not only Ptolemy, Copernicus, Kepler, Newton, Herschel, and Einstein but also hundreds of other minor protagonists who played an important role in the development of this, the most ancient yet the most modern of all the sciences. The book also examines in depth the diverse areas which have contributed to the history of astronomy, including the instrumentation, the theories, and the observations. Many stamps illustrate the beauty and the mystery of ce...

  6. SPS commemorative stamp

    CERN Multimedia

    1977-01-01

    The turn on of the SPS was commemorated in France by the issue of a CERN stamp. The date of issue, 22 Octber 1976, coincided with the first tests of the beam line taking particles to experiments in the West Hall. (CERN Courier 1976 p. 382)

  7. Rapid thermal processing by stamping

    Science.gov (United States)

    Stradins, Pauls; Wang, Qi

    2013-03-05

    A rapid thermal processing device and methods are provided for thermal processing of samples such as semiconductor wafers. The device has components including a stamp (35) having a stamping surface and a heater or cooler (40) to bring it to a selected processing temperature, a sample holder (20) for holding a sample (10) in position for intimate contact with the stamping surface; and positioning components (25) for moving the stamping surface and the stamp (35) in and away from intimate, substantially non-pressured contact. Methods for using and making such devices are also provided. These devices and methods allow inexpensive, efficient, easily controllable thermal processing.

  8. Analysis of alternative technologies stamping compressor blades of marine engines

    Directory of Open Access Journals (Sweden)

    Олександр Сергійович Аніщенко

    2015-10-01

    Full Text Available The author has made an analysis of several technologies stamping forgings compressor blades from titanium alloy ВT3-1. These technologies use different types of forming equipment: crank hot press, high-speed hammers, screw presses with hydraulic drive (SPHD, as well as isothermal forging hydraulic press. He pointed out the main advantages and disadvantages of the technology, noting that high-speed punching in the shipbuilding industry of Ukraine is not used for the manufacture of forgings blades. The article contains an economic analysis of the cost of forgings blades, which are made on four technologies: punching and calibration to crank hot press, stamping and calibration to press for isothermal forging, stamping and calibration on SPHD-press, stamping on SPHD-press and calibration to press for isothermal forging. The author has identified the effective use of these technologies. He showed that the use of SPHD-presses and hydraulic presses for isothermal forging reduces the cost of forging on the average 12% in comparison with the technology at the crank hot stamping press, increases the utilization of metal 1,3-1,5 times more, reduces power consumption 1,05-3,0 times less and complexity of manufacturing 1,8-4,2 times. However SPHD-press increases capital investment in the organization of stamping technology 2,6-5,3 times more and depreciation 2-4 times. Isothermal forging technology requires the cost of the stamps in 1,4-2,0 times higher than stamps for crank presses. The author argues that stamping forging blades technology improvement should be implemented saving basic materials first of all. Efficiency of isothermal stamping and calibration will be the higher, the more geometric dimensions of stamped forgings are

  9. METAMORPHOSES OF THE ENVIRONMENTAL STAMP IN ROMANIA

    Directory of Open Access Journals (Sweden)

    CARAUS MADALINA

    2015-12-01

    Full Text Available Romania's alignment to European standards is a difficult process with many legislative changes, with direct impact on taxpayers. The necessity of collecting substantial revenues to the State budget, which provide vital economic growth of the Romanian State, loses the substance when we are talking about taxes levied in relation to taxpayer. The environmental stamp, otherwise a controversial tax, represent for the State another way to earn revenue in advance, “as a loan", because in the end it's forced to repay the amounts concerned taxpayers, under the effect of a final and irrevocable court decision. The effects of the legislative changes bring every time complaints both from taxpayers, because they can demand repayment of the environmental stamp only during the period of prescription, as well as on the part of public servants who are grappling with a large volume of work, with the possibility of overcoming the term to handle requests. An equitable solution in solving these distortions would be the inclusion of the environmental stamp within the tax on means of transport, tax that is paid annually by vehicle owners. At the moment the level of the environmental stamp is calculated depending on the CO2 emissions, exhaust emissions and the age of the vehicle. Tax on means of transport is calculated based on engine capacity, an amount determined by CO2 emissions multiplying with each group of 200 cc or fraction on it. Therefore the unification of the two taxes would create a balance for all categories of vehicles.

  10. Timing system observations

    International Nuclear Information System (INIS)

    Winans, J.

    1994-01-01

    The purpose of this document is to augment Synchronized Time Stamp Support authored by Jim Kowalkowski. This document provides additional documentation to clarify and explain software involved in timing operations of the accelerator

  11. Fabrication of Nanoimprint stamps for photonic crystals

    International Nuclear Information System (INIS)

    Kouba, J; Kubenz, M; Mai, A; Ropers, G; Eberhardt, W; Loechel, B

    2006-01-01

    We report on fabrication of nanoimprint stamps for fabrication of two dimensional photonic crystals in visible range of spectra. Nanoimprint stamps made of silicon and/or nickel were successfully fabricated using electron beam lithography and advanced dry etching techniques. The quality of the stamps was evaluated using scanning electron microscopy. The fabricated stamps were also evaluated by imprinting them into suitable polymer materials

  12. Development of Methods and Equipment for Sheet Stamping

    Science.gov (United States)

    Botashev, A. Yu; Bisilov, N. U.; Malsugenov, R. S.

    2018-03-01

    New methods of sheet stamping were developed: the gas forming with double-sided heating of a blank part and the gas molding with backpressure. In case of the first method the blank part is heated to the set temperature by means of a double-sided impact of combustion products of gas mixtures, after which, under the influence of gas pressure a stamping process is performed. In case of gas molding with backpressure, the blank part is heated to the set temperature by one-sided impact of the combustion products, while backpressure is created on the opposite side of the blank part by compressed air. In both methods the deformation takes place in the temperature range of warm or hot treatment due to the heating of a blank part. This allows one to form parts of complicated shape within one technological operation, which significantly reduces the cost of production. To implement these methods, original devices were designed and produced, which are new types of forging and stamping equipment. Using these devices, an experimental research on the stamping process was carried out and high-quality parts were obtained, which makes it possible to recommend the developed methods of stamping in the industrial production. Their application in small-scale production will allow one to reduce the cost price of stamped parts 2 or 3 times.

  13. Stamp Verification for Automated Document Authentication

    DEFF Research Database (Denmark)

    Micenková, Barbora; van Beusekom, Joost; Shafait, Faisal

    Stamps, along with signatures, can be considered as the most widely used extrinsic security feature in paper documents. In contrast to signatures, however, for stamps little work has been done to automatically verify their authenticity. In this paper, an approach for verification of color stamps ...... and copied stamps. Sensitivity and specificity of up to 95% could be obtained on a data set that is publicly available....

  14. Stamping the Earth from space

    CERN Document Server

    Dicati, Renato

    2017-01-01

    This unique book presents a historical and philatelic survey of Earth exploration from space. It covers all areas of research in which artificial satellites have contributed in designing a new image of our planet and its environment: the atmosphere and ionosphere, the magnetic field, radiation belts and the magnetosphere, weather, remote sensing, mapping of the surface, observation of the oceans and marine environments, geodesy, and the study of life and ecological systems. Stamping the Earth from Space presents the results obtained with the thousands of satellites launched by the two former superpowers, the Soviet Union and the United States, and also those of the many missions carried out by the ESA, individual European countries, Japan, China, India, and the many emerging space nations. Beautifully illustrated, it contains almost 1100 color reproductions of philatelic items. In addition to topical stamps and thematic postal documents, the book provides an extensive review of astrophilatelic items. The most...

  15. A burial with a stamp seal depicting a Bes-like figure from Abusir

    Czech Academy of Sciences Publication Activity Database

    Dulíková, V.; Odler, M.; Březinová, Helena; Havelková, P.

    2015-01-01

    Roč. 2015, č. 15 (2015), s. 69-75 ISSN 1214-3189 Institutional support: RVO:67985912 Keywords : Abusir * Old Kingdom * First Intermediate Period * stamp seal * amulet * Bes * reed coffin * entheses Subject RIV: AC - Archeology, Anthropology, Ethnology

  16. Influence of Prepreg Characteristics on Stamp Consolidation

    NARCIS (Netherlands)

    Slange, T.K.; Warnet, L.L.; Grouve, W.J.B.; Akkerman, R.

    2017-01-01

    Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. The development of automated lay-up technologies further extends the applicability of stamp forming by allowing rapid lay-up of tailored blanks and

  17. ‚The Spirit of the Time Left its Stamp on These Works‘. Writing the History of the Shoah at the Jewish Historical Institute in Stalinist Poland

    Czech Academy of Sciences Publication Activity Database

    Stach, Stephan

    2016-01-01

    Roč. 5, č. 5 (2016), s. 185-211 ISSN 2084-3518 R&D Projects: GA ČR(CZ) GJ16-01775Y Institutional support: RVO:68378114 Keywords : Poland * Jewish history * holocaust memory Subject RIV: AB - History http://www.enrs.eu/studies_files/4/

  18. Experimental Validation for Hot Stamping Process by Using Taguchi Method

    Science.gov (United States)

    Fawzi Zamri, Mohd; Lim, Syh Kai; Razlan Yusoff, Ahmad

    2016-02-01

    Due to the demand for reduction in gas emissions, energy saving and producing safer vehicles has driven the development of Ultra High Strength Steel (UHSS) material. To strengthen UHSS material such as boron steel, it needed to undergo a process of hot stamping for heating at certain temperature and time. In this paper, Taguchi method is applied to determine the appropriate parameter of thickness, heating temperature and heating time to achieve optimum strength of boron steel. The experiment is conducted by using flat square shape of hot stamping tool with tensile dog bone as a blank product. Then, the value of tensile strength and hardness is measured as response. The results showed that the lower thickness, higher heating temperature and heating time give the higher strength and hardness for the final product. In conclusion, boron steel blank are able to achieve up to 1200 MPa tensile strength and 650 HV of hardness.

  19. Electro-optic sampling at 90 degree interaction geometry for time-of-arrival stamping of ultrafast relativistic electron diffraction

    OpenAIRE

    C. M. Scoby; P. Musumeci; J. T. Moody; M. S. Gutierrez

    2010-01-01

    In this paper we study a new geometry setup for electro-optic sampling (EOS) where the electron beam runs parallel to the ⟨110⟩ face of a ZnTe crystal and the probe laser is perpendicular to it and to the beam path. The simple setup is used to encode the time-of-arrival information of a 3.5  MeV

  20. Focused ion beam scan routine, dwell time and dose optimizations for submicrometre period planar photonic crystal components and stamps in silicon

    International Nuclear Information System (INIS)

    Hopman, Wico C L; Ay, Feridun; Hu, Wenbin; Gadgil, Vishwas J; Kuipers, Laurens; Pollnau, Markus; Ridder, Rene M de

    2007-01-01

    Focused ion beam (FIB) milling is receiving increasing attention for nanostructuring in silicon (Si). These structures can for example be used for photonic crystal structures in a silicon-on-insulator (SOI) configuration or for moulds which can have various applications in combination with imprint technologies. However, FIB fabrication of submicrometre holes having perfectly vertical sidewalls is still challenging due to the redeposition effect in Si. In this study we show how the scan routine of the ion beam can be used as a sidewall optimization parameter. The experiments have been performed in Si and SOI. Furthermore, we show that sidewall angles as small as 1.5 0 are possible in Si membranes using a spiral scan method. We investigate the effect of the dose, loop number and dwell time on the sidewall angle, interhole milling and total milling depth by studying the milling of single and multiple holes into a crystal. We show that the sidewall angles can be as small as 5 0 in (bulk) Si and SOI when applying a larger dose. Finally, we found that a relatively large dwell time of 1 ms and a small loop number is favourable for obtaining vertical sidewalls. By comparing the results with those obtained by others, we conclude that the number of loops at a fixed dose per hole is the parameter that determines the sidewall angle and not the dwell time by itself

  1. Stamping SERS for creatinine sensing

    Science.gov (United States)

    Li, Ming; Du, Yong; Zhao, Fusheng; Zeng, Jianbo; Santos, Greggy M.; Mohan, Chandra; Shih, Wei-Chuan

    2015-03-01

    Urine can be obtained easily, readily and non-invasively. The analysis of urine can provide metabolic information of the body and the condition of renal function. Creatinine is one of the major components of human urine associated with muscle metabolism. Since the content of creatinine excreted into urine is relatively constant, it is used as an internal standard to normalize water variations. Moreover, the detection of creatinine concentration in urine is important for the renal clearance test, which can monitor the filtration function of kidney and health status. In more details, kidney failure can be imminent when the creatinine concentration in urine is high. A simple device and protocol for creatinine sensing in urine samples can be valuable for point-of-care applications. We reported quantitative analysis of creatinine in urine samples by using stamping surface enhanced Raman scattering (S-SERS) technique with nanoporous gold disk (NPGD) based SERS substrate. S-SERS technique enables label-free and multiplexed molecular sensing under dry condition, while NPGD provides a robust, controllable, and high-sensitivity SERS substrate. The performance of S-SERS with NGPDs is evaluated by the detection and quantification of pure creatinine and creatinine in artificial urine within physiologically relevant concentration ranges.

  2. Usage and Recall of the Food Stamp Office Resource Kit (FSORK) by Food Stamp Applicants in 4 California Counties

    Science.gov (United States)

    Ghirardelli, Alyssa; Linares, Amanda; Fong, Amy

    2011-01-01

    Objective: To evaluate recall and usage of the Food Stamp Office Resource Kit (FSORK), a set of nutrition education materials designed for use in food stamp offices. Design: Client intercept exit surveys, an environmental scan, and individual observations of clients in the food stamp office. Setting: Four food stamp offices in California.…

  3. Efficient constraint-based Sequential Pattern Mining (SPM algorithm to understand customers’ buying behaviour from time stamp-based sequence dataset

    Directory of Open Access Journals (Sweden)

    Niti Ashish Kumar Desai

    2015-12-01

    Full Text Available Business Strategies are formulated based on an understanding of customer needs. This requires development of a strategy to understand customer behaviour and buying patterns, both current and future. This involves understanding, first how an organization currently understands customer needs and second predicting future trends to drive growth. This article focuses on purchase trend of customer, where timing of purchase is more important than association of item to be purchased, and which can be found out with Sequential Pattern Mining (SPM methods. Conventional SPM algorithms worked purely on frequency identifying patterns that were more frequent but suffering from challenges like generation of huge number of uninteresting patterns, lack of user’s interested patterns, rare item problem, etc. Article attempts a solution through development of a SPM algorithm based on various constraints like Gap, Compactness, Item, Recency, Profitability and Length along with Frequency constraint. Incorporation of six additional constraints is as well to ensure that all patterns are recently active (Recency, active for certain time span (Compactness, profitable and indicative of next timeline for purchase (Length―Item―Gap. The article also attempts to throw light on how proposed Constraint-based Prefix Span algorithm is helpful to understand buying behaviour of customer which is in formative stage.

  4. Electro-optic sampling at 90 degree interaction geometry for time-of-arrival stamping of ultrafast relativistic electron diffraction

    Directory of Open Access Journals (Sweden)

    C. M. Scoby

    2010-02-01

    Full Text Available In this paper we study a new geometry setup for electro-optic sampling (EOS where the electron beam runs parallel to the ⟨110⟩ face of a ZnTe crystal and the probe laser is perpendicular to it and to the beam path. The simple setup is used to encode the time-of-arrival information of a 3.5  MeV<10  pC electron bunch on the spatial profile of the laser pulse. The electric field lines inside the dielectric bend at an angle due to a relatively large (n∼3 index of refraction of the ZnTe crystal. We found theoretically and experimentally that the EOS signal can be maximized with a proper choice of incoming laser polarization angle. We achieved single-shot nondestructive measurement of the relative time of arrival between the pump and the probe beams thus improving the temporal resolution of ultrafast relativistic electron diffraction experiments.

  5. Influence of prepreg characteristics on stamp consolidation

    Science.gov (United States)

    Slange, T. K.; Warnet, L. L.; Grouve, W. J. B.; Akkerman, R.

    2017-10-01

    Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. The development of automated lay-up technologies further extends the applicability of stamp forming by allowing rapid lay-up of tailored blanks and partial preconsolidation. This partial preconsolidation makes the influence of prepreg more critical compared to conventional preconsolidation methods which provide full preconsolidation. This paper aims to highlight consolidation challenges that can appear when stamp forming blanks manufactured by automated lay-up. Important prepreg characteristics were identified based on an experimental study where a comparison was made between various prepreg in their as-received, deconsolidated and stamp consolidated state. It was found that adding up small thickness variations across the width of a prepreg when stacking plies into a blank by automated lay-up can cause non-uniform consolidation. Additionally, deconsolidation of the prepreg does not seem to obstruct interlaminar bonding, while intralaminar voids initially present in a prepreg cannot be removed during stamp forming. An additional preconsolidation step after automated lay-up seems necessary to remove blank thickness variations and intralaminar voids for the current prepregs. Eliminating this process step and the successful combination of rapid automated lay-up and stamp forming requires prepregs which are void-free and have less thickness variation.

  6. High Thermal Conductivity and High Wear Resistance Tool Steels for cost-effective Hot Stamping Tools

    Science.gov (United States)

    Valls, I.; Hamasaiid, A.; Padré, A.

    2017-09-01

    In hot stamping/press hardening, in addition to its shaping function, the tool controls the cycle time, the quality of the stamped components through determining the cooling rate of the stamped blank, the production costs and the feasibility frontier for stamping a given component. During the stamping, heat is extracted from the stamped blank and transported through the tool to the cooling medium in the cooling lines. Hence, the tools’ thermal properties determine the cooling rate of the blank, the heat transport mechanism, stamping times and temperature distribution. The tool’s surface resistance to adhesive and abrasive wear is also an important cost factor, as it determines the tool durability and maintenance costs. Wear is influenced by many tool material parameters, such as the microstructure, composition, hardness level and distribution of strengthening phases, as well as the tool’s working temperature. A decade ago, Rovalma developed a hot work tool steel for hot stamping that features a thermal conductivity of more than double that of any conventional hot work tool steel. Since that time, many complimentary grades have been developed in order to provide tailored material solutions as a function of the production volume, degree of blank cooling and wear resistance requirements, tool geometries, tool manufacturing method, type and thickness of the blank material, etc. Recently, Rovalma has developed a new generation of high thermal conductivity, high wear resistance tool steel grades that enable the manufacture of cost effective tools for hot stamping to increase process productivity and reduce tool manufacturing costs and lead times. Both of these novel grades feature high wear resistance and high thermal conductivity to enhance tool durability and cut cycle times in the production process of hot stamped components. Furthermore, one of these new grades reduces tool manufacturing costs through low tool material cost and hardening through readily

  7. Process control for sheet-metal stamping process modeling, controller design and shop-floor implementation

    CERN Document Server

    Lim, Yongseob; Ulsoy, A Galip

    2014-01-01

    Process Control for Sheet-Metal Stamping presents a comprehensive and structured approach to the design and implementation of controllers for the sheet metal stamping process. The use of process control for sheet-metal stamping greatly reduces defects in deep-drawn parts and can also yield large material savings from reduced scrap. Sheet-metal forming is a complex process and most often characterized by partial differential equations that are numerically solved using finite-element techniques. In this book, twenty years of academic research are reviewed and the resulting technology transitioned to the industrial environment. The sheet-metal stamping process is modeled in a manner suitable for multiple-input multiple-output control system design, with commercially available sensors and actuators. These models are then used to design adaptive controllers and real-time controller implementation is discussed. Finally, experimental results from actual shopfloor deployment are presented along with ideas for further...

  8. Characteristic Evaluation of Organic Light-Emitting Diodes Prepared with Stamp Printing Technique

    Directory of Open Access Journals (Sweden)

    Apisit Chittawanij

    2017-01-01

    Full Text Available We have reported on a stamp printing technique that uses PET release film as a printing stamp to deposit TPBi thin film served as the electron transport layer of the organic light-emitting diodes. TPBi thin film was printed with a good uniformity and resolution. Effect of deposition conditions on optical and electrical properties and surface roughness of TPBi thin film have been studied under spectroscopy and atomic force microscopy, respectively. It is found that characteristic of TPBi thin film is improved via controlled stamp temperature and time. Since TPBi thin film exhibits the surface morphology comparable to that of conventional spin-coating thin film, our findings suggest that PET release film-based stamp printing approach is possible to use as an alternative deposition of the organic thin film as compared with a traditional one.

  9. Stamp Detection in Color Document Images

    DEFF Research Database (Denmark)

    Micenkova, Barbora; van Beusekom, Joost

    2011-01-01

    , moreover, it can be imprinted with a variable quality and rotation. Previous methods were restricted to detection of stamps of particular shapes or colors. The method presented in the paper includes segmentation of the image by color clustering and subsequent classification of candidate solutions...... by geometrical and color-related features. The approach allows for differentiation of stamps from other color objects in the document such as logos or texts. For the purpose of evaluation, a data set of 400 document images has been collected, annotated and made public. With the proposed method, recall of 83...

  10. The effect of cushion-ram pulsation on hot stamping

    Science.gov (United States)

    Landgrebe, Dirk; Rautenstrauch, Anja; Kunke, Andreas; Polster, Stefan; Kriechenbauer, Sebastian; Mauermann, Reinhard

    2016-10-01

    Hot stamping is an important technology for manufacturing high-strength components. This technology offers the possibility to achieve significant weight reductions. In this study, cushion-ram pulsation (CRP), a new technology for hot stamping on servo-screw presses, was investigated and applied for hot stamping. Compared to a conventional process, the tests yielded a significantly higher drawing depth. In this paper, the CRP technology and the first test results with hot stamping were described in comparison to the conventional process.

  11. E-Commerce-Objected E-Stamp Systems

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Boosting e-stamp's advantages are conduced to promote logistics to go forward and help postal departments to improve the quality of service, many other businesses add-valued can be developed in e-stamp systems. This paper analyzeds, designs e-commerce-objected e-stamp system, and discusseds crucial technologies involved in detail.

  12. 78 FR 10201 - Proposed Information Collection; Electronic Duck Stamp Program

    Science.gov (United States)

    2013-02-13

    ..., Interior. ACTION: Notice; request for comments. SUMMARY: We (U.S. Fish and Wildlife Service) will ask the... refuges where admission is charged. Duck Stamps and products that bear stamp images are also popular... fee the State will charge for issuance of an electronic stamp. Description of the process the State...

  13. Postage stamps: A convergence of metallurgy, art, and history

    Science.gov (United States)

    Habashi, Fathi

    2002-04-01

    Postage stamps have been used around the world to commemorate, in miniature, significant events and people, including those of importance in the history of metals and mineral production. From the presence of gold artifacts in an ancient Egyptian tomb to the role of uranium in nuclear power, stamps have captured the evolution of metallurgical processes. This article highlights some of those stamps.

  14. Ex-Post : The Investment Performance of Collectible Stamps

    NARCIS (Netherlands)

    Dimson, E.; Spaenjers, C.

    2009-01-01

    This paper investigates the returns on British collectible postage stamps over the very long run, based on stamp catalogue prices. Between 1900 and 2008, we find an annualized return on stamps of 6.7% in nominal terms, which is equivalent to an average real return of 2.7% per annum. Prices have

  15. Fast thermal nanoimprint lithography by a stamp with integrated heater

    DEFF Research Database (Denmark)

    Tormen, Massimo; Malureanu, Radu; Pedersen, Rasmus Haugstrup

    2008-01-01

    We propose fast nanoimprinting lithography (NIL) process based on the use of stamps with integrated heater. The latter consists of heavily ion implantation n-type doped silicon layer buried below the microstructured surface of the stamp. The stamp is heated by Joule effect, by 50 μs 25 Hz...

  16. Hot stamping advanced manufacturing technology of lightweight car body

    CERN Document Server

    Hu, Ping; He, Bin

    2017-01-01

    This book summarizes the advanced manufacturing technology of original innovations in hot stamping of lightweight car body. A detailed description of the technical system and basic knowledge of sheet metal forming is given, which helps readers quickly understand the relevant knowledge in the field. Emphasis has been placed on the independently developed hot stamping process and equipment, which help describe the theoretical and experimental research on key problems involving stress field, thermal field and phase transformation field in hot stamping process. Also, a description of the formability at elevated temperature and the numerical simulation algorithms for high strength steel hot stamping is given in combination with the experiments. Finally, the book presents some application cases of hot stamping technology such as the lightweight car body design using hot stamping components and gradient hardness components, and the cooling design of the stamping tool. This book is intended for researchers, engineers...

  17. Nostalgia: retreat or support in difficult times?

    Science.gov (United States)

    Batcho, Krystine Irene

    2013-01-01

    The relationship between nostalgia and coping during difficult times was explored in 2 empirical studies. In the first, 80 undergraduates, 60 women and 20 men, completed the Nostalgia Inventory, a measure of nostalgia proneness, the COPE Inventory, a dispositional measure of strategies for coping with stressful events, and the Childhood Survey, a survey of impressions of childhood experiences. Nostalgia proneness correlated with use of adaptive coping, including emotional social support, expressing emotions, turning to religion, and suppressing competing activities, and did not correlate with escapist or avoidance strategies, including denial, behavioral disengagement, and substance abuse. Nostalgia proneness was related positively to favorable emotional and behavioral childhood experiences and did not correlate with adverse experiences. Favorable impressions of childhood correlated positively with adaptive coping strategies and inversely with dysfunctional ones, whereas unfavorable childhood experiences correlated positively with dysfunctional coping. Regression analyses suggested that the relationship between nostalgia proneness and certain coping strategies may be mediated in part by childhood experiences. In a second study, 100 undergraduates, 86 women and 14 men, completed the Nostalgia Inventory, recalled autobiographical memories that illustrated how childhood is either special or similar to their present life, and rated their likely use of strategies in dealing with 2 hypothetical problems. Nostalgia proneness correlated with emotional and instrumental social coping and with the goal-directed strategies of planning, taking action, and positive reframing. Further research is recommended to explore the role of childhood memories in coping and to identify mechanisms that mediate the relationship between nostalgia and coping.

  18. DOUBLE SHEAR DESIGN TO REDUCED STAMPING FORCE

    Directory of Open Access Journals (Sweden)

    Rudi Kurniawan Arief

    2017-12-01

    Full Text Available Ideally processing of part using stamping machine using only 70-80 % of available force to keep machine in good shape for a long periods. But in some certain case the force may equal to or exceed the available maximum force so the company must sent the process to another outsource company. A case found in a metal stamping company where a final product consist of 3 parts to assembly with one part exceeded the force of available machine. This part can only process in a 1000 tons machine while this company only have 2 of this machine with full workload. Sending this parts outsource will induce delivery problems because other parts are processed, assembled and paint inhouse, this also need additional transportation cost and extra supervision to ensure the quality and delivery schedule. The only exit action of this problem is by reducing the force tonnage. This paper using punch inclining method to reduce the force. The incline punch will distributed the force along the inclined surface that reduce stamping force as well. Inclined surface of punch also cause another major problems that the product becoming curved after process. This problems solved with additional flattening process that add more process cost but better than to outsource the process. Chisel type of inclining punch tip was choosen to avoid worst deformation of product. This paper will give the scientific recomendation to the company.

  19. STAMP alters the growth of transformed and ovarian cancer cells

    International Nuclear Information System (INIS)

    He, Yuanzheng; Blackford, John A Jr; Kohn, Elise C; Simons, S Stoney Jr

    2010-01-01

    Steroid receptors play major roles in the development, differentiation, and homeostasis of normal and malignant tissue. STAMP is a novel coregulator that not only enhances the ability of p160 coactivator family members TIF2 and SRC-1 to increase gene induction by many of the classical steroid receptors but also modulates the potency (or EC 50 ) of agonists and the partial agonist activity of antisteroids. These modulatory activities of STAMP are not limited to gene induction but are also observed for receptor-mediated gene repression. However, a physiological role for STAMP remains unclear. The growth rate of HEK293 cells stably transfected with STAMP plasmid and overexpressing STAMP protein is found to be decreased. We therefore asked whether different STAMP levels might also contribute to the abnormal growth rates of cancer cells. Panels of different stage human cancers were screened for altered levels of STAMP mRNA. Those cancers with the greatest apparent changes in STAMP mRNA were pursued in cultured cancer cell lines. Higher levels of STAMP are shown to have the physiologically relevant function of reducing the growth of HEK293 cells but, unexpectedly, in a steroid-independent manner. STAMP expression was examined in eight human cancer panels. More extensive studies of ovarian cancers suggested the presence of higher levels of STAMP mRNA. Lowering STAMP mRNA levels with siRNAs alters the proliferation of several ovarian cancer tissue culture lines in a cell line-specific manner. This cell line-specific effect of STAMP is not unique and is also seen for the conventional effects of STAMP on glucocorticoid receptor-regulated gene transactivation. This study indicates that a physiological function of STAMP in several settings is to modify cell growth rates in a manner that can be independent of steroid hormones. Studies with eleven tissue culture cell lines of ovarian cancer revealed a cell line-dependent effect of reduced STAMP mRNA on cell growth rates. This

  20. Stamping, Clapping and Chanting: An Ancient Learning Pathway?

    Directory of Open Access Journals (Sweden)

    Marion M. Long

    2006-04-01

    Full Text Available In this review I explore the effect of temporal integration as a means of improving learning in schoolchildren. I focus first on theorists that have linked physical activity with a positive effect on children’s learning and second to psychological studies that have established the existence of innate temporal patterns. These findings are related to a model of temporal integration that I have developed from Croce’s writings on aesthetics (1900. From philosophy to neurology, I discuss recent neurological findings relating to timing and conclude that an organ of temporal integration, regulation and coordination operates in the brain with respect to physical, intuitive and higher cognitive function. I link recent findings in neurophysiology to notably similar findings in recent biomusicological studies. The finding that humans have an involuntary physical response to loud, low-frequency sounds are attributed to an innate legacy of proto-music and proto-dance behaviour among hominids. I develop the model of temporal integration further by examining the literature on stamping and clapping patterns of ancient traditional dances in relation to Husserl’s writings on theoretical succession. From philosophy to pedagogy, I summarise the review by proposing stamping, clapping and chanting as a means of achieving improved temporal integration.

  1. How Do Stamp Duties Affect the Housing Market?

    OpenAIRE

    Davidoff, Ian; Leigh, Andrew

    2013-01-01

    Land transfer taxes are a substantial portion of the cost of moving house in many developed countries. Since stamp duties are endogenous with respect to the house price, we create an instrumental variable that is the stamp duty on a property, given that postcode's starting house price and the national house price trend. In a specification with postcode and year fixed effects, this instrument effectively captures policy changes and nonlinearities in the stamp duty schedule. We find that the im...

  2. Stamp duties in Indian states - a case for reform

    OpenAIRE

    Alm, James; Annez, Patricia; Modi, Arbind

    2004-01-01

    The authors review the options for reform of stamp duties on immovable property transfers collected by Indian state governments. After briefly reviewing some of the many administrative difficulties experienced with the tax, they turn to an examination of its economic impacts. A review of stamp duties internationally indicates that Indian rates are exceptionally high, at rates often above 1...

  3. 27 CFR 479.87 - Cancellation of stamp.

    Science.gov (United States)

    2010-04-01

    ... OTHER FIREARMS Transfer Tax Application and Order for Transfer of Firearm § 479.87 Cancellation of stamp. The method of cancellation of the stamp required by this subpart as prescribed in § 479.67 shall be used. Exemptions Relating to Transfers of Firearms ...

  4. Programming the BasicStamp : using MacBS2

    NARCIS (Netherlands)

    Djajadiningrat, J.P.; Stienstra, M.

    2004-01-01

    This article explains how to program a BasicStamp microcontroller using a Macintosh. It takes an absolute beginner's perspective and talks you through the whole process including how to hook up a programmer board, how to write some programs in the BasisStamp language PBASIC, and how to do some

  5. Patterning of polymers: precise channel stamping by optimizing wetting properties

    International Nuclear Information System (INIS)

    Seemann, Ralf; Kramer, Edward J; Lange, Frederick F

    2004-01-01

    Channel stamping is a soft lithography technique that can be used to fabricate small structures of polymeric materials. This technique is cheap and easy but a considerable drawback is the fact that reproduction of the patterns of the stamp is often imprecise due to the wetting properties of liquid and stamp. In this paper, we report on experiments that reveal the parameters governing the behaviour of liquids in grooves and on edges. Optimizing these parameters leads to better-quality channel-stamped structures and enables the design of sophisticated structured polymeric materials, allowing channels as small as about 100 nm to be fabricated. Moreover, we show that it is even possible to build up a freestanding three-dimensional structure by stamping line patterns on top of each other

  6. Stamping of Thin-Walled Structural Components with Magnesium Alloy AZ31 Sheets

    International Nuclear Information System (INIS)

    Chen, F.-K.; Chang, C.-K.

    2005-01-01

    In the present study, the stamping process for manufacturing cell phone cases with magnesium alloy AZ31 sheets was studied using both the experimental approach and the finite element analysis. In order to determine the proper forming temperature and set up a fracture criterion, tensile tests and forming limit tests were first conducted to obtain the mechanical behaviors of AZ31 sheets at various elevated temperatures. The mechanical properties of Z31 sheets obtained from the experiments were then adopted in the finite element analysis to investigate the effects of the process parameters on the formability of the stamping process of cell phone cases. The finite element simulation results revealed that both the fracture and wrinkle defects could not be eliminated at the same time by adjusting blank-holder force or blank size. A drawbead design was then performed using the finite element simulations to determine the size and the location of drawbead required to suppress the wrinkle defect. An optimum stamping process, including die geometry, forming temperature, and blank dimension, was then determined for manufacturing the cell phone cases. The finite element analysis was validated by the good agreement between the simulation results and the experimental data. It confirms that the cell phone cases can be produced with magnesium alloy AZ31 sheet by the stamping process at elevated temperatures

  7. POLYELECTROLYTE MULTILAYER STAMPING IN AQUEOUS PHASE AND NON-CONTACT MODE

    Science.gov (United States)

    Mehrotra, Sumit; Lee, Ilsoon; Liu, Chun; Chan, Christina

    2011-01-01

    Polyelectrolyte multilayer (PEM) transfer printing has been previously achieved by stamping under dry conditions. Here, we show for the first time, that PEM can be transferred from a stamp to the base substrate under aqueous conditions whereby the two surfaces are in a non-contact mode. Degradable multilayers of (PAA/PEG)10.5 followed by non-degradable multilayers of (PDAC/SPS)80.5 were fabricated under acidic pH conditions on either PDMS or glass (stamp), and subsequently transferred over top of another multilayer prepared on a different substrate (base substrate), with a spacing of ~ 200 μm between the stamping surface and the base substrate. This multilayer transfer was performed under physiological pH conditions. This process is referred to herein as non-contact, aqueous-phase multilayer (NAM) transfer. NAM transfer can be useful for applications such as fabricating three-dimensional (3-D) cellular scaffolds. We attempted to create a 3-D cellular scaffold using NAM transfer, and characterized the scaffolds with conventional and fluorescence microscopy. PMID:21860540

  8. Fabrication of a roller type PDMS stamp using SU-8 concave molds and its application for roll contact printing

    International Nuclear Information System (INIS)

    Park, Jongho; Kim, Beomjoon

    2016-01-01

    Continuous fabrication of micropatterns at low-cost is attracting attention in various applications within industrial fields. To meet such demands, we have demonstrated a roll contact printing technique, using roller type polydimethylsiloxane (PDMS) stamps with roll-to-flat and roll-to-roll stages. Roller type PDMS stamps for roll contact printing were fabricated using a custom-made metal support and SU-8 microstructures fabricated on concave substrates as a mold. The molding/casting method which we developed here provided faster and easier fabrication than conventional methods for roller type stamps. Next, roll contact printing was performed using fabricated roller type PDMS stamps with roll-to-flat and roll-to-roll stages. Patterns with minimum widths of 3 μm and 2.1 μm were continuously fabricated for each stage, respectively. In addition, the relationship between applied pressures and dimensional changes of roll contact printed patterns was investigated. Finally, we confirmed that roll contact printing and the new fabrication method for roller stamps presented in this study demonstrated the feasibility for industrial applications. (paper)

  9. Characterization of thermoplastic composites for hot stamp forming

    NARCIS (Netherlands)

    Rietman, Bert; Grouve, Wouter; Akkerman, Remko

    2014-01-01

    This paper describes state-of-the-art characterization methods for thermoplastic composites at high processing temperature and provides a few examples of application in simulations of the hot stamp forming process.

  10. Tribological Behavior of Laser Textured Hot Stamping Dies

    Directory of Open Access Journals (Sweden)

    Andre Shihomatsu

    2016-01-01

    Full Text Available Hot stamping of high strength steels has been continuously developed in the automotive industry to improve mechanical properties and surface quality of stamped components. One of the main challenges faced by researchers and technicians is to improve stamping dies lifetime by reducing the wear caused by high pressures and temperatures present during the process. This paper analyzes the laser texturing of hot stamping dies and discusses how different surfaces textures influence the lubrication and wear mechanisms. To this purpose, experimental tests and numerical simulation were carried out to define the die region to be texturized and to characterize the textured surface topography before and after hot stamping tests with a 3D surface profilometer and scanning electron microscopy. Results showed that laser texturing influences the lubrication at the interface die-hot sheet and improves die lifetime. In this work, the best texture presented dimples with the highest diameter, depth, and spacing, with the surface topography and dimples morphology practically preserved after the hot stamping tests.

  11. Why Stamp Duties are an Increasing Financial Burden on Australian Home Buyers

    OpenAIRE

    Wood, Gavin A.

    1994-01-01

    The purchaser of housing incurs stamp duty liabilities in all Australian States. These stamp duties are levied on the conveyance of residential property and mortgage sums secured. In general, stamp duties were a growing financial burden on home buyers during the period 1985-1991. This paper examines the role of house price inflation in causing increases in average rates of stamp duty, the responsiveness of average rates of stamp duty to future changes in the nominal tax base and the effective...

  12. Precision Time Protocol support hardware for ATCA control and data acquisition system

    Energy Technology Data Exchange (ETDEWEB)

    Correia, Miguel, E-mail: miguelfc@ipfn.ist.utl.pt [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal); Sousa, Jorge; Carvalho, Bernardo B.; Santos, Bruno; Carvalho, Paulo F.; Rodrigues, António P.; Combo, Álvaro M.; Pereira, Rita C. [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal); Correia, Carlos M.B.A. [Centro de Instrumentação, Departamento de Física, Universidade de Coimbra, 3004-516 Coimbra (Portugal); Gonçalves, Bruno [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal)

    2015-10-15

    Highlights: • ATCA based control and data acquisition subsystem has been developed at IPFN. • PTP and time stamping were implemented with VHDL and PTP daemon (PTPd) codes. • The RTM (…) provides PTP synchronization with an external GMC. • The main advantage is that timestamps are generated closer to the Physical Layer at the GMII. • IPFN's upgrade consistently exhibited jitter values below 25 ns RMS. - Abstract: An in-house, Advanced Telecom Computing Architecture (ATCA) based control and data acquisition (C&DAQ) subsystem has been developed at Instituto de Plasmas e Fusão Nuclear (IPFN), aiming for compliance with the ITER Fast Plant System Controller (FPSC). Timing and synchronization for the ATCA modules connects to ITER Control, Data Access and Communication (CODAC) through the Timing Communication Network (TCN), which uses IEEE 1588-2008 Precision Time Protocol (PTP) to synchronize devices to a Grand Master Clock (GMC). The TCN infrastructure was tested for an RMS jitter under the limit of 50 ns. Therefore, IPFN's hardware, namely the ATCA-PTSW-AMC4 hub-module, which is in charge of timing and synchronization distribution for all subsystem endpoints, shall also perform within this jitter limit. This paper describes a relevant upgrade, applied to the ATCA-PTSW-AMC4 hardware, to comply with these requirements – in particular, the integration of an add-on module “RMC-TMG-1588” on its Rear Transition Module (RTM). This add-on is based on a commercial FPGA-based module from Trenz Electronic, using the ZHAW “PTP VHDL code for timestamping unit and clock”, which features clock offset and drift correction and hardware-assisted time stamping. The main advantage is that timestamps are generated closer to the Physical Layer, at the Gigabit Ethernet Media Independent Interface (GMII), avoiding the timing uncertainties accumulated through the upper layers. PTP code and user software run in a MicroBlaze™ soft-core CPU with Linux in the

  13. Precision Time Protocol support hardware for ATCA control and data acquisition system

    International Nuclear Information System (INIS)

    Correia, Miguel; Sousa, Jorge; Carvalho, Bernardo B.; Santos, Bruno; Carvalho, Paulo F.; Rodrigues, António P.; Combo, Álvaro M.; Pereira, Rita C.; Correia, Carlos M.B.A.; Gonçalves, Bruno

    2015-01-01

    Highlights: • ATCA based control and data acquisition subsystem has been developed at IPFN. • PTP and time stamping were implemented with VHDL and PTP daemon (PTPd) codes. • The RTM (…) provides PTP synchronization with an external GMC. • The main advantage is that timestamps are generated closer to the Physical Layer at the GMII. • IPFN's upgrade consistently exhibited jitter values below 25 ns RMS. - Abstract: An in-house, Advanced Telecom Computing Architecture (ATCA) based control and data acquisition (C&DAQ) subsystem has been developed at Instituto de Plasmas e Fusão Nuclear (IPFN), aiming for compliance with the ITER Fast Plant System Controller (FPSC). Timing and synchronization for the ATCA modules connects to ITER Control, Data Access and Communication (CODAC) through the Timing Communication Network (TCN), which uses IEEE 1588-2008 Precision Time Protocol (PTP) to synchronize devices to a Grand Master Clock (GMC). The TCN infrastructure was tested for an RMS jitter under the limit of 50 ns. Therefore, IPFN's hardware, namely the ATCA-PTSW-AMC4 hub-module, which is in charge of timing and synchronization distribution for all subsystem endpoints, shall also perform within this jitter limit. This paper describes a relevant upgrade, applied to the ATCA-PTSW-AMC4 hardware, to comply with these requirements – in particular, the integration of an add-on module “RMC-TMG-1588” on its Rear Transition Module (RTM). This add-on is based on a commercial FPGA-based module from Trenz Electronic, using the ZHAW “PTP VHDL code for timestamping unit and clock”, which features clock offset and drift correction and hardware-assisted time stamping. The main advantage is that timestamps are generated closer to the Physical Layer, at the Gigabit Ethernet Media Independent Interface (GMII), avoiding the timing uncertainties accumulated through the upper layers. PTP code and user software run in a MicroBlaze™ soft-core CPU with Linux in the same FPGA

  14. Impact of Simulation Technology on Die and Stamping Business

    Science.gov (United States)

    Stevens, Mark W.

    2005-08-01

    Over the last ten years, we have seen an explosion in the use of simulation-based techniques to improve the engineering, construction, and operation of GM production tools. The impact has been as profound as the overall switch to CAD/CAM from the old manual design and construction methods. The changeover to N/C machining from duplicating milling machines brought advances in accuracy and speed to our construction activity. It also brought significant reductions in fitting sculptured surfaces. Changing over to CAD design brought similar advances in accuracy, and today's use of solid modeling has enhanced that accuracy gain while finally leading to the reduction in lead time and cost through the development of parametric techniques. Elimination of paper drawings for die design, along with the process of blueprinting and distribution, provided the savings required to install high capacity computer servers, high-speed data transmission lines and integrated networks. These historic changes in the application of CAE technology in manufacturing engineering paved the way for the implementation of simulation to all aspects of our business. The benefits are being realized now, and the future holds even greater promise as the simulation techniques mature and expand. Every new line of dies is verified prior to casting for interference free operation. Sheet metal forming simulation validates the material flow, eliminating the high costs of physical experimentation dependent on trial and error methods of the past. Integrated forming simulation and die structural analysis and optimization has led to a reduction in die size and weight on the order of 30% or more. The latest techniques in factory simulation enable analysis of automated press lines, including all stamping operations with corresponding automation. This leads to manufacturing lines capable of running at higher levels of throughput, with actual results providing the capability of two or more additional strokes per

  15. Real time traffic models, decision support for traffic management

    NARCIS (Netherlands)

    Wismans, Luc Johannes Josephus; de Romph, E.; Friso, K.; Zantema, K.

    2014-01-01

    Reliable and accurate short-term traffic state prediction can improve the performance of real-time traffic management systems significantly. Using this short-time prediction based on current measurements delivered by advanced surveillance systems will support decision-making processes on various

  16. Real Time Traffic Models, Decision Support for Traffic Management

    NARCIS (Netherlands)

    Wismans, L.; De Romph, E.; Friso, K.; Zantema, K.

    2014-01-01

    Reliable and accurate short-term traffic state prediction can improve the performance of real-time traffic management systems significantly. Using this short-time prediction based on current measurements delivered by advanced surveillance systems will support decision-making processes on various

  17. Later School Start Times: What Informs Parent Support or Opposition?

    Science.gov (United States)

    Dunietz, Galit Levi; Matos-Moreno, Amilcar; Singer, Dianne C; Davis, Matthew M; O'Brien, Louise M; Chervin, Ronald D

    2017-07-15

    To investigate parental knowledge about adolescent sleep needs, and other beliefs that may inform their support for or objection to later school start times. In 2014, we conducted a cross-sectional, Internet-based survey of a nationally representative sample of parents as part of the C.S. Mott Children's Hospital National Poll on Children's Health. Parents with teens aged 13-17 years reported their children's sleep patterns and school schedules, and whether the parents supported later school start times (8:30 am or later). Responses associated with parental support of later school start times were examined with logistic regression analysis. Overall, 88% of parents reported school start times before 8:30 am, and served as the analysis sample (n = 554). In this group, 51% expressed support for later school start times. Support was associated with current school start times before 7:30 am (odds ratio [OR] = 3.1 [95% confidence interval (CI) 1.2, 8.4]); parental opinion that their teen's current school start time was "too early" (OR = 3.8 [1.8, 7.8]); and agreement with American Academy of Pediatrics recommendations about school start times (OR = 4.7 [2.2, 10.1]). Support also was associated with anticipation of improved school performance (OR = 3.0 [1.5, 5.9]) or increased sleep duration (OR = 4.0 [1.8, 8.9]) with later school start times. Conversely, parents who anticipated too little time for after-school activities (OR = 0.5 [0.3, 0.9]) and need for different transportation plans (OR = 0.5 [0.2, 0.9]) were often less supportive. Parental education about healthy sleep needs and anticipated health benefits may increase their support for later school start times. Educational efforts should also publicize the positive experiences of communities that have made this transition, with regard to limited adverse effect on after-school activity schedules and transportation. © 2017 American Academy of Sleep Medicine

  18. Ada Run Time Support Environments and a common APSE Interface Set. [Ada Programming Support Environment

    Science.gov (United States)

    Mckay, C. W.; Bown, R. L.

    1985-01-01

    The paper discusses the importance of linking Ada Run Time Support Environments to the Common Ada Programming Support Environment (APSE) Interface Set (CAIS). A non-stop network operating systems scenario is presented to serve as a forum for identifying the important issues. The network operating system exemplifies the issues involved in the NASA Space Station data management system.

  19. Supporting collaborative discussions on asynchronous time: a technological perspective

    OpenAIRE

    Caballé, Santi

    2011-01-01

    The aim of this paper is to report on an experience of using an innovative on-line learning tool to support real, collaborative learning through discussion in asynchronous time. While asynchronous interaction gives rise to unique opportunities that support active, collaborative learning, unique problems also arise, such as frustration, caused by waiting for other peoples' reactions and feedback and the consequent loss of motivation, which has a negative impact on learning outcomes. In order t...

  20. Stochastic analysis and robust optimization for a deck lid inner panel stamping

    International Nuclear Information System (INIS)

    Hou, Bo; Wang, Wurong; Li, Shuhui; Lin, Zhongqin; Xia, Z. Cedric

    2010-01-01

    FE-simulation and optimization are widely used in the stamping process to improve design quality and shorten development cycle. However, the current simulation and optimization may lead to non-robust results due to not considering the variation of material and process parameters. In this study, a novel stochastic analysis and robust optimization approach is proposed to improve the stamping robustness, where the uncertainties are involved to reflect manufacturing reality. A meta-model based stochastic analysis method is developed, where FE-simulation, uniform design and response surface methodology (RSM) are used to construct meta-model, based on which Monte-Carlo simulation is performed to predict the influence of input parameters variation on the final product quality. By applying the stochastic analysis, uniform design and RSM, the mean and the standard deviation (SD) of product quality are calculated as functions of the controllable process parameters. The robust optimization model composed of mean and SD is constructed and solved, the result of which is compared with the deterministic one to show its advantages. It is demonstrated that the product quality variations are reduced significantly, and quality targets (reject rate) are achieved under the robust optimal solution. The developed approach offers rapid and reliable results for engineers to deal with potential stamping problems during the early phase of product and tooling design, saving more time and resources.

  1. Prediction of Proper Temperatures for the Hot Stamping Process Based on the Kinetics Models

    Science.gov (United States)

    Samadian, P.; Parsa, M. H.; Mirzadeh, H.

    2015-02-01

    Nowadays, the application of kinetics models for predicting microstructures of steels subjected to thermo-mechanical treatments has increased to minimize direct experimentation, which is costly and time consuming. In the current work, the final microstructures of AISI 4140 steel sheets after the hot stamping process were predicted using the Kirkaldy and Li kinetics models combined with new thermodynamically based models in order for the determination of the appropriate process temperatures. In this way, the effect of deformation during hot stamping on the Ae3, Acm, and Ae1 temperatures was considered, and then the equilibrium volume fractions of phases at different temperatures were calculated. Moreover, the ferrite transformation rate equations of the Kirkaldy and Li models were modified by a term proposed by Åkerström to consider the influence of plastic deformation. Results showed that the modified Kirkaldy model is satisfactory for the determination of appropriate austenitization temperatures for the hot stamping process of AISI 4140 steel sheets because of agreeable microstructure predictions in comparison with the experimental observations.

  2. FIRST TIME ONLINE LEARNERS’ PERCEPTIONS OF SUPPORT SERVICES PROVIDED

    Directory of Open Access Journals (Sweden)

    Stephanie HUNTE

    2012-04-01

    Full Text Available The number of online continuous education and training initiatives continues to increase in Caribbean Small Island Developing States (SIDS and by extension, the number of adult learners who are unfamiliar with the peculiarities of the online teaching and learning environment. The extent to which these learners can derive maximum benefit from these initiatives depends on the rate at which they can adapt to the new circumstances and, as a result, function effectively in this type of teaching and learning environment. To this end, while supporting learners is recognized as a critical success factor little has been explored or documented specific to the Caribbean-SIDS context. The purpose of this study therefore was to describe the support services provided first time online learners in the context of Caribbean-SIDS and examine what if any benefit learners derived from them through their perceptions of these services. The findings reveal that participants’ overall perception of the support services was high. They also reveal that although participants’ awareness of ongoing support services was variable, their rating of the need for and importance of this type of support was also high. The findings suggest that providing support for first time online learners in the context of Caribbean SIDS positively impacts their performance in the online teaching and learning environment.

  3. Technology, Time, and Participation: How a Principal Supports Teachers.

    Science.gov (United States)

    McCarthy, Robert B.

    1985-01-01

    Argues that administrations might better support teachers if they provided: (1) up-to-date technology, such as Xerox machines; (2) "guilt-free" time for curriculum work or special projects; and (3) more opportunities for teacher participation in school decision making. (KH)

  4. Tea Time: Raising Awareness and Support for Extension

    Science.gov (United States)

    Franz, Nancy K.; Fahey, Chris

    2012-01-01

    In a time of reliance on electronic media for information, chaotic programming environments, and declining public resources, Extension workers need to find unique ways to connect with stakeholders to maintain and increase support for programming. To address this need, we developed, conducted, and evaluated a series of stakeholder teas. We found…

  5. Draw-in Map - A Road Map for Simulation-Guided Die Tryout and Stamping Process Control

    International Nuclear Information System (INIS)

    Wang Chuantao; Zhang, Jimmy J.; Goan, Norman

    2005-01-01

    Sheet metal forming is a displacement or draw-in controlled manufacturing process in which a flat blank is drawn into die cavity to form an automotive body panel. Draw-in amount is the single most important stamping manufacturing index that controls all forming characteristics (strains, stresses, thinning, etc.), stamping failures (splits, wrinkles, surface distortion, etc.) and line die operations and automations. Draw-in Map is engineered for math-based die developments via advanced stamping simulation technology. Then the Draw-in Map is provided to die makers in plants as a road map for math-guided die tryout in which the die tryout workers follow the engineered tryout conditions and matches the engineered draw-in amount so that the tryout time and cost are greatly reduced, and quality is ensured. The Map can also be used as a math-based trouble-shooting tool to identify the causes of formability problems in stamping production. The engineered Draw-in Map has been applied to all draw die tryout for all GM vehicle programs since 1998. A minimum 50% reduction in both lead-time and cost and significant improvement in panel quality in tryout have been reported. This paper presents the concept and process to apply the engineered Draw-in Map in die tryout

  6. Sulforaphane inhibits osteoclast differentiation by suppressing the cell-cell fusion molecules DC-STAMP and OC-STAMP

    International Nuclear Information System (INIS)

    Takagi, Tomohiro; Inoue, Hirofumi; Takahashi, Nobuyuki; Katsumata-Tsuboi, Rie; Uehara, Mariko

    2017-01-01

    Sulforaphane (SFN), a kind of isothiocyanate, is derived from broccoli sprouts. It has anti-tumor, anti-inflammatory, and anti-oxidation activity. The molecular function of SFN in the inhibition of osteoclast differentiation is not well-documented. In this study, we assessed the effect of SFN on osteoclast differentiation in vitro. SFN inhibited osteoclast differentiation in both bone marrow cells and RAW264.7 cells. Key molecules involved in the inhibitory effects of SFN on osteoclast differentiation were determined using a microarray analysis, which showed that SFN inhibits osteoclast-associated genes, such as osteoclast-associated receptor (OSCAR), nuclear factor of activated T cells cytoplasmic-1, tartrate-resistant acid phosphatase, and cathepsin K. Moreover, the mRNA expression levels of the cell-cell fusion molecules dendritic cell specific transmembrane protein (DC-STAMP) and osteoclast stimulatory transmembrane protein (OC-STAMP) were strongly suppressed in cells treated with SFN. Furthermore, SFN increased the phosphorylation of signal transducer and activator of transcription 1 (STAT1), a regulator of macrophage and osteoclast cell fusion. Thus, our data suggested that SFN significantly inhibits the cell-cell fusion molecules DC-STAMP and OC-STAMP by inducing the phosphorylation of STAT1 (Tyr701), which might be regulated by interactions with OSCAR. - Highlights: • Sulforaphane inhibited osteoclast differentiation and osteoclast cell-fusion. • Sulforaphane suppressed not only NFATc1, but also cell-cell fusion molecules, DC-STAMP and OC-STAMP. • Sulforaphane decreased multinucleated osteoclasts, whereas increased mono-nucleated osteoclasts. • Sulforaphane inhibits the cell-cell fusion by inducing the phosphorylation of STAT1 (Tyr701).

  7. Constellation Program Electrical Ground Support Equipment Research and Development

    Science.gov (United States)

    McCoy, Keegan S.

    2010-01-01

    At the Kennedy Space Center, I engaged in the research and development of electrical ground support equipment for NASA's Constellation Program. Timing characteristics playa crucial role in ground support communications. Latency and jitter are two problems that must be understood so that communications are timely and consistent within the Kennedy Ground Control System (KGCS). I conducted latency and jitter tests using Alien-Bradley programmable logic controllers (PLCs) so that these two intrinsic network properties can be reduced. Time stamping and clock synchronization also play significant roles in launch processing and operations. Using RSLogix 5000 project files and Wireshark network protocol analyzing software, I verified master/slave PLC Ethernet module clock synchronization, master/slave IEEE 1588 communications, and time stamping capabilities. All of the timing and synchronization test results are useful in assessing the current KGCS operational level and determining improvements for the future.

  8. Real-time information support for managing plant emergency responses

    International Nuclear Information System (INIS)

    Cain, D.G.; Lord, R.J.; Wilkinson, C.D.

    1983-01-01

    The Three Mile Island Unit 2 accident highlighted the need to develop a systematic approach to managing plant emergency responses, to identify a better decision-making process, and to implement real-time information support for decision-making. The overall process management function is described and general information requirements for management of plant emergencies are identified. Basic information systems are being incorporated and future extensions and problem areas are discussed. (U.K.)

  9. Dashboard visualizations: Supporting real-time throughput decision-making.

    Science.gov (United States)

    Franklin, Amy; Gantela, Swaroop; Shifarraw, Salsawit; Johnson, Todd R; Robinson, David J; King, Brent R; Mehta, Amit M; Maddow, Charles L; Hoot, Nathan R; Nguyen, Vickie; Rubio, Adriana; Zhang, Jiajie; Okafor, Nnaemeka G

    2017-07-01

    Providing timely and effective care in the emergency department (ED) requires the management of individual patients as well as the flow and demands of the entire department. Strategic changes to work processes, such as adding a flow coordination nurse or a physician in triage, have demonstrated improvements in throughput times. However, such global strategic changes do not address the real-time, often opportunistic workflow decisions of individual clinicians in the ED. We believe that real-time representation of the status of the entire emergency department and each patient within it through information visualizations will better support clinical decision-making in-the-moment and provide for rapid intervention to improve ED flow. This notion is based on previous work where we found that clinicians' workflow decisions were often based on an in-the-moment local perspective, rather than a global perspective. Here, we discuss the challenges of designing and implementing visualizations for ED through a discussion of the development of our prototype Throughput Dashboard and the potential it holds for supporting real-time decision-making. Copyright © 2017. Published by Elsevier Inc.

  10. Real-time multi-task operators support system

    International Nuclear Information System (INIS)

    Wang He; Peng Minjun; Wang Hao; Cheng Shouyu

    2005-01-01

    The development in computer software and hardware technology and information processing as well as the accumulation in the design and feedback from Nuclear Power Plant (NPP) operation created a good opportunity to develop an integrated Operator Support System. The Real-time Multi-task Operator Support System (RMOSS) has been built to support the operator's decision making process during normal and abnormal operations. RMOSS consists of five system subtasks such as Data Collection and Validation Task (DCVT), Operation Monitoring Task (OMT), Fault Diagnostic Task (FDT), Operation Guideline Task (OGT) and Human Machine Interface Task (HMIT). RMOSS uses rule-based expert system and Artificial Neural Network (ANN). The rule-based expert system is used to identify the predefined events in static conditions and track the operation guideline through data processing. In dynamic status, Back-Propagation Neural Network is adopted for fault diagnosis, which is trained with the Genetic Algorithm. Embedded real-time operation system VxWorks and its integrated environment Tornado II are used as the RMOSS software cross-development. VxGUI is used to design HMI. All of the task programs are designed in C language. The task tests and function evaluation of RMOSS have been done in one real-time full scope simulator. Evaluation results show that each task of RMOSS is capable of accomplishing its functions. (authors)

  11. design and development of a soap stamping and tableting machine

    African Journals Online (AJOL)

    2012-07-02

    Jul 2, 2012 ... for these two operations. The manual ... chine, the cutting and stamping operations were done at different .... slack side belt tensions Tj were determined as 131.66N and 162.71N for the .... vironmental Management, Vol. 6, No.

  12. 41 CFR 101-25.103-3 - Trading stamps or bonus goods received from contractors.

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Trading stamps or bonus... PROCUREMENT 25-GENERAL 25.1-General Policies § 101-25.103-3 Trading stamps or bonus goods received from contractors. When contracts contain a price reduction clause, any method (such as trading stamps or bonus...

  13. Online discussion compensates for suboptimal timing of supportive information presentation in a digitally supported learning environment

    NARCIS (Netherlands)

    Noroozi, O.; Busstra, M.C.; Mulder, M.; Biemans, H.J.A.; Tobi, H.; Geelen, A.; Veer, van 't P.; Chizari, M.

    2012-01-01

    This study used a sequential set-up to investigate the consecutive effects of timing of supportive information presentation (information before vs. information during the learning task clusters) in interactive digital learning materials (IDLMs) and type of collaboration (personal discussion vs.

  14. Acceleration (Deceleration Model Supporting Time Delays to Refresh Data

    Directory of Open Access Journals (Sweden)

    José Gerardo Carrillo González

    2018-04-01

    Full Text Available This paper proposes a mathematical model to regulate the acceleration (deceleration applied by self-driving vehicles in car-following situations. A virtual environment is designed to test the model in different circumstances: (1 the followers decelerate in time if the leader decelerates, considering a time delay of up to 5 s to refresh data (vehicles position coordinates required by the model, (2 with the intention of optimizing space, the vehicles are grouped in platoons, where 3 s of time delay (to update data is supported if the vehicles have a centre-to-centre spacing of 20 m and a time delay of 1 s is supported at a spacing of 6 m (considering a maximum speed of 20 m/s in both cases, and (3 an algorithm is presented to manage the vehicles’ priority at a traffic intersection, where the model regulates the vehicles’ acceleration (deceleration and a balance in the number of vehicles passing from each side is achieved.

  15. Can Food Stamps Do More to Improve Food Choices? An Economic Perspective--Higher Cost of Food in Some Areas May Affect Food Stamp Households' Ability To Make Healthy Food Choices

    OpenAIRE

    Nord, Mark; Hopwood, Heather

    2007-01-01

    The cost of “enough food,” estimated from the amount that low- and medium-income households in a geographic area report needing to spend to just meet their food needs, differs substantially across States and among metropolitan areas. In areas with high food costs, many food-stamp recipients are likely to have inadequate food resources to support healthy food choices.

  16. Optimal higher-order encoder time-stamping

    NARCIS (Netherlands)

    Merry, R.J.E.; Molengraft, van de M.J.G.; Steinbuch, M.

    2013-01-01

    Optical incremental encoders are used to measure the position of motion control systems. The accuracy of the position measurement is determined and bounded by the number of slits on the encoder. The position measurement is affected by quantization errors and encoder imperfections. In this paper, an

  17. A compact system for large-area thermal nanoimprint lithography using smart stamps

    DEFF Research Database (Denmark)

    Pedersen, Rasmus Haugstrup; Hansen, Ole; Kristensen, Anders

    2008-01-01

    We present a simple apparatus for thermal nanoimprint lithography. In this work, the stamp is designed to significantly reduce the requirements for pressure application on the external imprint system. By MEMS-based processing, an air cavity inside the stamp is created, and the required pressure...... for successful imprint is reduced. Additionally, the stamp is capable of performing controlled demolding after imprint. Due to the complexity of the stamp, a compact and cost-effective imprint apparatus can be constructed. The design and fabrication of the advanced stamp as well as the simple imprint equipment...

  18. Support for the Logical Execution Time Model on a Time-predictable Multicore Processor

    DEFF Research Database (Denmark)

    Kluge, Florian; Schoeberl, Martin; Ungerer, Theo

    2016-01-01

    The logical execution time (LET) model increases the compositionality of real-time task sets. Removal or addition of tasks does not influence the communication behavior of other tasks. In this work, we extend a multicore operating system running on a time-predictable multicore processor to support...... the LET model. For communication between tasks we use message passing on a time-predictable network-on-chip to avoid the bottleneck of shared memory. We report our experiences and present results on the costs in terms of memory and execution time....

  19. Efficient methods of nanoimprint stamp cleaning based on imprint self-cleaning effect

    Energy Technology Data Exchange (ETDEWEB)

    Meng Fantao; Chu Jinkui [Key Laboratory for Micro/Nano Technology and System of Liaoning Province, Dalian University of Technology, 116024 Dalian (China); Luo Gang; Zhou Ye; Carlberg, Patrick; Heidari, Babak [Obducat AB, SE-20125 Malmoe (Sweden); Maximov, Ivan; Montelius, Lars; Xu, H Q [Division of Solid State Physics, Lund University, Box 118, S-22100 Lund (Sweden); Nilsson, Lars, E-mail: ivan.maximov@ftf.lth.se [Department of Food Technology, Engineering and Nutrition, Lund University, Box 117, S-22100 Lund (Sweden)

    2011-05-06

    Nanoimprint lithography (NIL) is a nonconventional lithographic technique that promises low-cost, high-throughput patterning of structures with sub-10 nm resolution. Contamination of nanoimprint stamps is one of the key obstacles to industrialize the NIL technology. Here, we report two efficient approaches for removal of typical contamination of particles and residual resist from stamps: thermal and ultraviolet (UV) imprinting cleaning-both based on the self-cleaning effect of imprinting process. The contaminated stamps were imprinted onto polymer substrates and after demolding, they were treated with an organic solvent. The images of the stamp before and after the cleaning processes show that the two cleaning approaches can effectively remove contamination from stamps without destroying the stamp structures. The contact angles of the stamp before and after the cleaning processes indicate that the cleaning methods do not significantly degrade the anti-sticking layer. The cleaning processes reported in this work could also be used for substrate cleaning.

  20. Attenuated Total Reflection Fourier Transform Infrared (ATR FT-IR) Spectroscopy as a Forensic Method to Determine the Composition of Inks Used to Print the United States One-cent Blue Benjamin Franklin Postage Stamps of the 19th Century.

    Science.gov (United States)

    Brittain, Harry G

    2016-01-01

    Through the combined use of infrared (IR) absorption spectroscopy and attenuated total reflectance (ATR) sampling, the composition of inks used to print the many different types of one-cent Benjamin Franklin stamps of the 19th century has been established. This information permits a historical evaluation of the formulations used at various times, and also facilitates the differentiation of the various stamps from each other. In two instances, the ink composition permits the unambiguous identification of stamps whose appearance is identical, and which (until now) have only been differentiated through estimates of the degree of hardness or softness of the stamp paper, or through the presence or absence of a watermark in the paper. In these instances, the use of ATR Fourier transform infrared spectroscopy (FT-IR) spectroscopy effectively renders irrelevant two 100-year-old practices of stamp identification. Furthermore, since the use of ATR sampling makes it possible to obtain the spectrum of a stamp still attached to its cover, it is no longer necessary to identify these blue Franklin stamps using their cancellation dates. © The Author(s) 2015.

  1. Protected time for nutrition support teams: What are the benefits?

    Science.gov (United States)

    Ceniccola, Guilherme D; Araújo, Wilma M C; de Brito-Ashurst, Ione; Abreu, Henrique B; Akutsu, Rita de C

    2016-12-01

    Nutrition support teams (NSTs) are important and unique entities in acute care hospitals. Despite their utility, NSTs are lacking in the majority of hospitals worldwide and where they exist, most members only spend a fraction of their time working within that role. We aim to evaluate the effect of protected time on NST performance by assessing the influence of structure and process in NST activities. All large public hospitals (>250 beds) in the Brazilian Federal District were evaluated with a structured questionnaire designed to assess NST performance. The questionnaire was adapted to include the Donabedian quality processes comprising 54 questions split amongst 6 domains; mainly structure and processes. The percentage of questionnaire compliance (NST outcome) was utilized to assess differences regarding structure and process. Hospitals with protected time to NST activities (Group I) were compared to hospitals without NSTs protected times (Group II). Seven hospitals were assessed. Group I, n = 3, showed a significantly higher performance outcome than Group II, n = 4 (77.9 × 60.3; P = 0.004), and only Group I's score achieved the benchmark for quality standards (75% compliance). Significant differences between groups were also found in structure (P = 0.017) and process (P = 0.014). This study indicates that protected time for NST activities is paramount to increase NST performance and could positively influence Donabedian quality indicators. Our results highlight the importance of NSTs in large hospitals and is an advocate for public policies requiring dedicated time for NST work. Only a larger study can confirm our findings. Copyright © 2016 European Society for Clinical Nutrition and Metabolism. All rights reserved.

  2. Soil Temperature and Moisture Profile (STAMP) System Handbook

    Energy Technology Data Exchange (ETDEWEB)

    Cook, David R. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-11-01

    The soil temperature and moisture profile system (STAMP) provides vertical profiles of soil temperature, soil water content (soil-type specific and loam type), plant water availability, soil conductivity, and real dielectric permittivity as a function of depth below the ground surface at half-hourly intervals, and precipitation at one-minute intervals. The profiles are measured directly by in situ probes at all extended facilities of the SGP climate research site. The profiles are derived from measurements of soil energy conductivity. Atmospheric scientists use the data in climate models to determine boundary conditions and to estimate the surface energy flux. The data are also useful to hydrologists, soil scientists, and agricultural scientists for determining the state of the soil. The STAMP system replaced the SWATS system in early 2016.

  3. CO2 Laser Cutting of Hot Stamping Boron Steel Sheets

    OpenAIRE

    Pasquale Russo Spena

    2017-01-01

    This study investigates the quality of CO2 laser cutting of hot stamping boron steel sheets that are employed in the fabrication of automotive body-in-white. For this purpose, experimental laser cutting tests were conducted on 1.2 mm sheets at varying levels of laser power, cutting speed, and oxygen pressure. The resulting quality of cut edges was evaluated in terms of perpendicularity tolerance, surface irregularity, kerf width, heat affected zone, and dross extension. Experimental tests wer...

  4. American Society of Mechanical Engineers' N stamp requirements

    International Nuclear Information System (INIS)

    Row, P.D.

    1977-01-01

    Incorporated with ASME Section III, Nuclear Power Plant Components, is an Appendix on Quality Assurance Systems which includes provision for ASME surveys. Manufacturers and installers passing the survey successfully receive an N Symbol Stamp and an ASME Certificate of Authorization. An outline is given of the prerequisites for a survey to be scheduled and of the requirements and procedures adopted by the survey team. (U.K.)

  5. Real-Time Clinical Decision Support Decreases Inappropriate Plasma Transfusion.

    Science.gov (United States)

    Shah, Neil; Baker, Steven A; Spain, David; Shieh, Lisa; Shepard, John; Hadhazy, Eric; Maggio, Paul; Goodnough, Lawrence T

    2017-08-01

    To curtail inappropriate plasma transfusions, we instituted clinical decision support as an alert upon order entry if the patient's recent international normalized ratio (INR) was 1.7 or less. The alert was suppressed for massive transfusion and within operative or apheresis settings. The plasma order was automatically removed upon alert acceptance while clinical exception reasons allowed for continued transfusion. Alert impact was studied comparing a 7-month control period with a 4-month intervention period. Monthly plasma utilization decreased 17.4%, from a mean ± SD of 3.40 ± 0.48 to 2.82 ± 0.6 plasma units per hundred patient days (95% confidence interval [CI] of difference, -0.1 to 1.3). Plasma transfused below an INR of 1.7 or less decreased from 47.6% to 41.6% (P = .0002; odds ratio, 0.78; 95% CI, 0.69-0.89). The alert recommendation was accepted 33% of the time while clinical exceptions were chosen in the remaining cases (active bleeding, 31%; other clinical indication, 33%; and apheresis, 2%). Alert acceptance rate varied significantly among different provider specialties. Clinical decision support can help curtail inappropriate plasma use but needs to be part of a comprehensive strategy including audit and feedback for comprehensive, long-term changes. © American Society for Clinical Pathology, 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

  6. FORMENTOR real-time decision support for risk management

    International Nuclear Information System (INIS)

    Pennings, R.; Gerlinger, G.; Ponamale, M.

    1995-01-01

    The supervision of complex industrial processes, such as in the chemical, nuclear or aerospace industries, is a difficult task. The FORMENTOR methodology allows the development of supervision support systems to aid operations in their tasks, especially when dealing with perturbations and hazardous situations. A FORMENTOR system presents a synthetic plant-wide view of the current situation, diagnoses the underlying causes of perturbations, predicts possible future evolutions and proposes remedial actions. For this the methodology integrates models, techniques and tools from four domains namely artificial intelligence, safety analysis, real-time computing and ergonomics. The methodological approach provides firm control over the development process while meeting the quality and technical requirements of the client; furthermore it ensures the reliability and maintainability of the obtained system

  7. Use of tobacco tax stamps to prevent and reduce illicit tobacco trade--United States, 2014.

    Science.gov (United States)

    Chriqui, Jamie; DeLong, Hillary; Gourdet, Camille; Chaloupka, Frank; Edwards, Sarah Matthes; Xu, Xin; Promoff, Gabbi

    2015-05-29

    Tobacco use is the leading cause of preventable disease and death in the United States. Increasing the unit price on tobacco products is the most effective tobacco prevention and control measure. Illicit tobacco trade (illicit trade) undermines high tobacco prices by providing tobacco users with cheaper-priced alternatives. In the United States, illicit trade primarily occurs when cigarettes are bought from states, jurisdictions, and federal reservation land with lower or no excise taxes, and sold in jurisdictions with higher taxes. Applying tax stamps to tobacco products, which provides documentation that taxes have been paid, is an important tool to combat illicit trade. Comprehensive tax stamping policy, which includes using digital, encrypted ("high-tech") stamps, applying stamps to all tobacco products, and working with tribes on stamping agreements, can further prevent and reduce illicit trade. This report describes state laws governing tax stamps on cigarettes, little cigars (cigarette-sized cigars), roll-your-own tobacco (RYOT), and tribal tobacco sales across the United States as of January 1, 2014, and assesses the extent of comprehensive tobacco tax stamping in the United States. Forty-four states (including the District of Columbia [DC]) applied traditional paper ("low-tech") tax stamps to cigarettes, whereas four authorized more effective high-tech stamps. Six states explicitly required stamps on other tobacco products (i.e., tobacco products other than cigarettes), and in approximately one third of states with tribal lands, tribes required tax stamping to address illicit purchases by nonmembers. No U.S. state had a comprehensive approach to tobacco tax stamping. Enhancing tobacco tax stamping across the country might further prevent and reduce illicit trade in the United States.

  8. Microstructure, Mechanical Properties, and Toughening Mechanisms of a New Hot Stamping-Bake Toughening Steel

    Science.gov (United States)

    Lin, Tao; Song, Hong-Wu; Zhang, Shi-Hong; Cheng, Ming; Liu, Wei-Jie; Chen, Yun

    2015-09-01

    In this article, the hot stamping-bake toughening process has been proposed following the well-known concept of bake hardening. The influences of the bake time on the microstructure and the mechanical properties of the hot stamped-baked part were studied by means of scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and mechanical tests at room temperature. The results show that the amount of the retained austenite was nearly not changed by the bake process. Also observed were spherical Cu-rich precipitates of about 15 nm in martensite laths. According to the Orowan mechanism, their contribution of the Cu-rich precipitates to the strength is approximately 245 MPa. With the increase of the bake time, the tensile strength of the part was decreased, whereas both the ductility and the product of the tensile strength and ductility were increased then decreased. The tensile strength and ductility product and the tensile strength are as high as 21.9 GPa pct, 2086 MPa, respectively. The excellent combined properties are due to the transformation-induced plasticity effect caused by retained austenite.

  9. Comparison of the hot-stamped boron-alloyed steel and the warm-stamped medium-Mn steel on microstructure and mechanical properties

    International Nuclear Information System (INIS)

    Li, Xiaodong; Chang, Ying; Wang, Cunyu; Hu, Ping; Dong, Han

    2017-01-01

    The application of high strength steels (HSS) for automotive structural parts is an effective way to realize lightweight and enhance safety. Therefore, improvements in mechanical properties of HSS are needed. In the present study, the warm stamping process of the third generation automotive medium-Mn steel was discussed, the characteristics of martensitic transformation were investigated, as well as the microstructure and mechanical properties were analyzed, compared to the popular hot-stamped 22MnB5 steel in the automotive industry. The results are indicated as follows. Firstly, the quenching rate of the medium-Mn steel can be selected in a wide range based on its CCT curves, which is beneficial to the control of forming process. Secondly, the influence of stamping temperature and pressure on the M s temperature of the medium-Mn steel is not obvious and can be neglected, which is favorable to the even distribution of martensitic microstructure and mechanical properties. Thirdly, the phenomenon of decarbonization is hardly found on the surface of the warm-stamped medium-Mn steel, and the ultra-fine-grained microstructure is found inside the medium-Mn steel after warm stamping. Besides, the warm-stamped medium-Mn steel holds the better comprehensive properties, such as a lower yield ratio, higher total elongation and higher tear toughness than the hot-stamped 22MnB5 steel. Furthermore, an actual warm-stamped B-pillar of medium-Mn steel is stamped and ultra-fine-grained martensitic microstructure is obtained. The mechanical properties are evenly distributed. As a result, this paper proves that the warm-stamped medium-Mn steel part can meet the requirements of lightweight and crash safety, and is promising for the industrial production of automotive structural parts.

  10. Comparison of the hot-stamped boron-alloyed steel and the warm-stamped medium-Mn steel on microstructure and mechanical properties

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xiaodong [School of Automotive Engineering, State Key Lab of Structural Analysis for Industrial Equipment, Dalian University of Technology, Dalian 116024 (China); Chang, Ying, E-mail: yingc@dlut.edu.cn [School of Automotive Engineering, State Key Lab of Structural Analysis for Industrial Equipment, Dalian University of Technology, Dalian 116024 (China); Wang, Cunyu [East China Branch of Central Iron & Steel Research Institute (CISRI), Beijing 100081 (China); Hu, Ping [School of Automotive Engineering, State Key Lab of Structural Analysis for Industrial Equipment, Dalian University of Technology, Dalian 116024 (China); Dong, Han [East China Branch of Central Iron & Steel Research Institute (CISRI), Beijing 100081 (China)

    2017-01-02

    The application of high strength steels (HSS) for automotive structural parts is an effective way to realize lightweight and enhance safety. Therefore, improvements in mechanical properties of HSS are needed. In the present study, the warm stamping process of the third generation automotive medium-Mn steel was discussed, the characteristics of martensitic transformation were investigated, as well as the microstructure and mechanical properties were analyzed, compared to the popular hot-stamped 22MnB5 steel in the automotive industry. The results are indicated as follows. Firstly, the quenching rate of the medium-Mn steel can be selected in a wide range based on its CCT curves, which is beneficial to the control of forming process. Secondly, the influence of stamping temperature and pressure on the M{sub s} temperature of the medium-Mn steel is not obvious and can be neglected, which is favorable to the even distribution of martensitic microstructure and mechanical properties. Thirdly, the phenomenon of decarbonization is hardly found on the surface of the warm-stamped medium-Mn steel, and the ultra-fine-grained microstructure is found inside the medium-Mn steel after warm stamping. Besides, the warm-stamped medium-Mn steel holds the better comprehensive properties, such as a lower yield ratio, higher total elongation and higher tear toughness than the hot-stamped 22MnB5 steel. Furthermore, an actual warm-stamped B-pillar of medium-Mn steel is stamped and ultra-fine-grained martensitic microstructure is obtained. The mechanical properties are evenly distributed. As a result, this paper proves that the warm-stamped medium-Mn steel part can meet the requirements of lightweight and crash safety, and is promising for the industrial production of automotive structural parts.

  11. Time Course of Brain Network Reconfiguration Supporting Inhibitory Control.

    Science.gov (United States)

    Popov, Tzvetan; Westner, Britta U; Silton, Rebecca L; Sass, Sarah M; Spielberg, Jeffrey M; Rockstroh, Brigitte; Heller, Wendy; Miller, Gregory A

    2018-05-02

    Hemodynamic research has recently clarified key nodes and links in brain networks implementing inhibitory control. Although fMRI methods are optimized for identifying the structure of brain networks, the relatively slow temporal course of fMRI limits the ability to characterize network operation. The latter is crucial for developing a mechanistic understanding of how brain networks shift dynamically to support inhibitory control. To address this critical gap, we applied spectrally resolved Granger causality (GC) and random forest machine learning tools to human EEG data in two large samples of adults (test sample n = 96, replication sample n = 237, total N = 333, both sexes) who performed a color-word Stroop task. Time-frequency analysis confirmed that recruitment of inhibitory control accompanied by slower behavioral responses was related to changes in theta and alpha/beta power. GC analyses revealed directionally asymmetric exchanges within frontal and between frontal and parietal brain areas: top-down influence of superior frontal gyrus (SFG) over both dorsal ACC (dACC) and inferior frontal gyrus (IFG), dACC control over middle frontal gyrus (MFG), and frontal-parietal exchanges (IFG, precuneus, MFG). Predictive analytics confirmed a combination of behavioral and brain-derived variables as the best set of predictors of inhibitory control demands, with SFG theta bearing higher classification importance than dACC theta and posterior beta tracking the onset of behavioral response. The present results provide mechanistic insight into the biological implementation of a psychological phenomenon: inhibitory control is implemented by dynamic routing processes during which the target response is upregulated via theta-mediated effective connectivity within key PFC nodes and via beta-mediated motor preparation. SIGNIFICANCE STATEMENT Hemodynamic neuroimaging research has recently clarified regional structures in brain networks supporting inhibitory control. However, due to

  12. Effects of Pre-Strain on the Aging Behavior of Al 7075 Alloy for Hot-Stamping Capability

    Directory of Open Access Journals (Sweden)

    Seon-Ho Jung

    2018-02-01

    Full Text Available The present study investigates the significance of pre-strain on the T6 aging behavior of an Al 7075 alloy for evaluating the applicability of hot stamping. In practice, the alloy was pre-strained up to 15% during solution heat treatment at 480 °C prior to quenching, and artificial aging was conducted at 120 °C. The peak aging time and precipitation behavior were compared with the alloy with pre-straining at room temperature after quenching but immediately before the artificial aging. The results showed that increasing amounts of pre-strain tend to reduce the aging time up to 50% for achieving peak hardness, which is consistent with the alloy at the T6 condition. There is a limitation for the maximum attainable amount of pre-strain of 10% for the homogeneous distribution of strain when the alloy is strained at room temperature (RT due to the low formability. The pre-strained alloy as hot stamping exhibited lowering of the peak reaction temperatures for dissolution and formation of Guinier–Preston (GP-Zones and precipitated with increasing amounts of pre-strain towards 15% through the differential scanning calorimetry analysis, thereby confirming the shortening of the peak aging time. The present study confirms the excellent potential of the hot-stamping process to extend the capability of an Al 7075 alloy.

  13. Improvement in current density of nano- and micro-structured Si solar cells by cost-effective elastomeric stamp process

    Science.gov (United States)

    Jeon, Kiseok; Jee, Hongsub; Lim, Sangwoo; Park, Min Joon; Jeong, Chaehwan

    2018-03-01

    Effective incident light should be controlled for improving the current density of solar cells by employing nano- and micro-structures on silicon surface. The elastomeric stamp process, which is more cost effective and simpler than conventional photolithography, was proposed for the fabrication of nano- and micro-structures. Polydimethylsiloxane (PDMS) was poured on a mother pattern with a diameter of 6 μm and a spacing of 2 μm; then, curing was performed to create a PDMS mold. The regular micropattern was stamped on a low-viscosity resin-coated silicon surface, followed by the simple reactive ion etching process. Nano-structures were formed using the Ag-based electroless etching process. As etching time was increased to 6 min, reflectance decreased to 4.53% and current density improved from 22.35 to 34.72 mA/cm2.

  14. Mathematical Modeling of Hydroelastic Oscillations of the Stamp and the Plate, Resting on Pasternak Foundation

    Science.gov (United States)

    Mogilevich, L. I.; Popov, V. S.; Popova, A. A.; Christoforova, A. V.

    2018-01-01

    The forced oscillations of the elastic fixed stamp and the plate, resting on Pasternak foundation are studied. The oscillations are caused by pressure pulsation in liquid layer between the stamp and the plate. Pasternak model is chosen as an elastic foundation. The laws of the stamp movement, the plate deflection and pressure in the liquid are discovered on the basis of hydroelasticity problem analytical solution. The functions of amplitude deflection distribution and liquid pressure along the plate are constructed, as well as the stamp amplitude-frequency characteristic. The obtained mathematical model allows to investigate the dynamics of hydroelastic interaction of the stamp with the plate, resting on elastic foundation, to define resonance frequencies of the plate and the stamp and corresponding deflections amplitudes, as well as liquid presser amplitudes.

  15. On the Determination of the Blank Shape Contour for Thin Precision Parts Obtained by Stamping

    International Nuclear Information System (INIS)

    Azaouzi, M.; Delameziere, A.; Naceur, H.; Batoz, J. L.; Sibaud, D.; Belouettar, S.

    2007-01-01

    The present study deals with the 'automatic' determination of the initial blank shape contour for 3D thin metallic precision parts obtained by stamping, knowing the 3D CAD geometry of the final part (the desired product). The forming process can involve several steps presented in this paper that consists in applying a heuristic method of optimization to find out the initial blank shape of thin precision metallic part in order to obtain a final part, with a required 3D geometry (specified). The purpose of the present approach is to replace the experimental trial and error optimization method used currently, which is expensive and time consuming. The principle of the 'heuristic' optimization method is to first estimate the blank shape using the Inverse Approach, then to compensate the shape error calculated in each node of the blank contour. The 'heuristic' optimization loop is done using a precise incremental code (Abaqus Explicit or Stampack) and, the iterations loop is stopped when the shape errors are within some initially fixed tolerances. The method is tested in the case of a special stamping process where the parts are pressed in one or more steps using a manual press, without blank holder and by the mean of tools having complex shape. The sensitivities of the process parameters regarding the optimal solution are investigated

  16. Springback Reduction in Stamping of Front Side Member with a Response Surface Method

    International Nuclear Information System (INIS)

    Song, Jung-Han; Huh, Hoon; Kim, Se-Ho; Park, Sung-Ho

    2005-01-01

    Springback is a common phenomenon in sheet metal forming since the elastic recovery of the internal stresses is induced after removal of the tooling. The numerical analysis of springback is a complicated time-consuming job and its result is greatly effected by a type of the yield function, finite elements used and the constraint condition for eliminating a rigid body motion. In this paper, optimization of the draw-bead force is carried out utilizing the response surface method in order to reduce springback and improve shape accuracy of a deep drawn product. In the optimization process, the tendency of springback is evaluated qualitatively without springback simulation usually done with the implicit solving scheme. Instead of springback simulation, the amount of stress deviation along the thickness direction in the deep drawn product is used as an indicator of springback. The stamping process is analyzed for a front side member formed with advanced high strength steel (AHSS) sheets such as DP60. The analysis procedure fully covers the binder-wrap, stamping, trimming and springback processes with the commercial elasto-plastic finite element code LS-DYNA 3D. The effect of the restraining force of draw-beads is confirmed with the decreased stress deviation. The analysis result shown in the final springback simulation demonstrates that the present analysis provides a guideline for controlling the evolution of springback based on the finite element simulation of complicated auto-body members

  17. Application of Modified Digital Halftoning Techniques to Data Hiding in Personalized Stamps

    Institute of Scientific and Technical Information of China (English)

    Hsi-Chun Wang; Chi-Ming Lian; Pei-Chi Hsiao

    2004-01-01

    The objective of this research is to embed information in personalized stamps by modified digital halftoning techniques. The displaced and deformed halftone dots are used to encode data in the personalized stamps. Hidden information can be retrieved by either an optical decoder or digital image processing techniques.The results show that personalized stamps with value-added features like data hiding or digital watermarking can be successfully implemented.

  18. Minerals on postage stamps: A mix of art, history, economics and geography

    Science.gov (United States)

    Glover, Paul

    2010-05-01

    Most people would agree that minerals represent some of the most beautiful natural objects known to mankind, especially in the form of precious and semi-precious gemstones. It is hardly surprising, therefore, that they are often illustrated on stamps. Examples are the fine crystalline forms represented as coloured etchings in the French 1986 issue, and the stylized simplicity of the mineral stamps that were part of the Swiss Pro Patria series, issued annually between 1958 and 1961. I aim in this presentation to introduce the beautiful world of mineral illustrations on stamps. The talk cannot be comprehensive because of the very large number of minerals and stamps concerned, but it will introduce the range of minerals depicted on stamps, then look in some greater detail at several sets from France, Southern Africa and East Germany. Minerals become the subject of sets of stamps for many reasons. In many cases, it is part of an attempt by the particular national post office to depict the whole of the natural history of their country in stamp form - a statement of nationality and politics. The 1986 French issue was an example which followed sets of stamps that had already portrayed insects, flowers, trees and birds native to France. We also find that certain countries have produced several sets of stamps to mark the importance to their economy of mining particular minerals. Many African states depend upon minerals for much of their wealth and economic power, explaining why, for instance, Sierra Leone issued over 35 stamps on the subject of diamonds between 1965 and 1978, and why over 77% of mineral stamps come from countries with major mining interests. Countries with traditional links with the history of the study of geology and mining also produce mineral stamps. These are usually European countries with a long record of the study of the Earth, such as Germany and Switzerland. Curiously enough, though, despite its fine tradition of geological observation and research

  19. Demonstration of decision support for real time operation

    DEFF Research Database (Denmark)

    Catterson, Victoria; MCarthur, Stephen; Chen, Minjiang

    ELECTRA Deliverable 8.2 reports on the demonstration of decision support within the future control room in light of voltage and frequency control in the 2030+ power system. The decision support must identify key threats and vulnerabilities, and propose and prioritise appropriate interventions....

  20. Analysis Of Die Design For The Stamping Of A Bathtub

    Directory of Open Access Journals (Sweden)

    Hojny M.

    2015-06-01

    Full Text Available The paper presents example results of numerical and photogrammetric analysis leading to identify the causes of cracking and wrinkling during bathtub W1200 production. The verification of tools for the stamping of bathtub W1200 was performed using finite element method and photogrammetric system ATOS Triple Scan. A series of industrial tests was conducted to identify the model parameters. The major and minor strain distributions obtained from the finite element simulations were used in conjunction with the forming limit diagram to predict the onset of fracture. In addition, the effects of blank holder pressure and friction on the occurrence of fracture and wrinkling were investigated.

  1. An interactive and flexible approach to stamping design and optimization

    International Nuclear Information System (INIS)

    Roy, Subir; Kunju, Ravi; Kirby, David

    2004-01-01

    This paper describes an efficient method that integrates finite element analysis (FEA), mesh morphing and response surface based optimization in order to implement an automated and flexible software tool to optimize stamping tool and process design. For FEA, a robust and extremely fast inverse solver is chosen. For morphing, a state of the art mesh morpher that interactively generates shape variables for optimization studies is used. The optimization algorithm utilized in this study enables a global search for a multitude of parameters and is highly flexible with regards to the choice of objective functions. A quality function that minimizes formability defects resulting from stretching and compression is implemented

  2. Investigation of the Phase Formation of AlSi-Coatings for Hot Stamping of Boron Alloyed Steel

    International Nuclear Information System (INIS)

    Veit, R.; Kolleck, R.; Hofmann, H.; Sikora, S.

    2011-01-01

    Hot stamping of boron alloyed steel is gaining more and more importance for the production of high strength automotive body parts. Within hot stamping of quenchenable steels the blank is heated up to austenitization temperature, transferred to the tool, formed rapidly and quenched in the cooled tool. To avoid scale formation during the heating process of the blank, the sheet metal can be coated with an aluminium-silicum alloy. The meltimg temperature of this coating is below the austenitization temperature of the base material. This means, that a diffusion process between base material and coating has to take place during heating, leading to a higher melting temperature of the coating.In conventional heating devices, like roller hearth furnaces, the diffusion process is reached by relatively low heating rates. New technologies, like induction heating, reach very high heating rates and offer great potentials for the application in hot stamping. Till now it is not proofed, that this technology can be used with aluminum-silicon coated materials. This paper will present the results of comparative heating tests with a conventional furnace and an induction heating device. For different time/temperature-conditions the phase formation within the coating will be described.

  3. Studies on the finite element simulation in sheet metal stamping processes

    Science.gov (United States)

    Huang, Ying

    The sheet metal stamping process plays an important role in modern industry. With the ever-increasing demand for shape complexity, product quality and new materials, the traditional trial and error method for setting up a sheet metal stamping process is no longer efficient. As a result, the Finite Element Modeling (FEM) method has now been widely used. From a physical point of view, the formability and the quality of a product are influenced by several factors. The design of the product in the initial stage and the motion of the press during the production stage are two of these crucial factors. This thesis focuses on the numerical simulation for these two factors using FEM. Currently, there are a number of commercial FEM software systems available in the market. These software systems are based on an incremental FEM process that models the sheet metal stamping process in small incremental steps. Even though the incremental FEM is accurate, it is not suitable for the initial conceptual design for its needing of detailed design parameters and enormous calculation times. As a result, another type of FEM, called the inverse FEM method or one-step FEM method, has been proposed. While it is less accurate than that of the incremental method, this method requires much less computation and hence, has a great potential. However, it also faces a number of unsolved problems, which limits its application. This motivates the presented research. After the review of the basic theory of the inverse method, a new modified arc-length search method is proposed to find better initial solution. The methods to deal with the vertical walls are also discussed and presented. Then, a generalized multi-step inverse FEM method is proposed. It solves two key obstacles: the first one is to determine the initial solution of the intermediate three-dimensional configurations and the other is to control the movement of nodes so they could only slide on constraint surfaces during the search by

  4. Time Capture Tool (TimeCaT): development of a comprehensive application to support data capture for Time Motion Studies.

    Science.gov (United States)

    Lopetegui, Marcelo; Yen, Po-Yin; Lai, Albert M; Embi, Peter J; Payne, Philip R O

    2012-01-01

    Time Motion Studies (TMS) have proved to be the gold standard method to measure and quantify clinical workflow, and have been widely used to assess the impact of health information systems implementation. Although there are tools available to conduct TMS, they provide different approaches for multitasking, interruptions, inter-observer reliability assessment and task taxonomy, making results across studies not comparable. We postulate that a significant contributing factor towards the standardization and spread of TMS would be the availability and spread of an accessible, scalable and dynamic tool. We present the development of a comprehensive Time Capture Tool (TimeCaT): a web application developed to support data capture for TMS. Ongoing and continuous development of TimeCaT includes the development and validation of a realistic inter-observer reliability scoring algorithm, the creation of an online clinical tasks ontology, and a novel quantitative workflow comparison method.

  5. DC-STAMP Is an Osteoclast Fusogen Engaged in Periodontal Bone Resorption.

    Science.gov (United States)

    Wisitrasameewong, W; Kajiya, M; Movila, A; Rittling, S; Ishii, T; Suzuki, M; Matsuda, S; Mazda, Y; Torruella, M R; Azuma, M M; Egashira, K; Freire, M O; Sasaki, H; Wang, C Y; Han, X; Taubman, M A; Kawai, T

    2017-06-01

    Dendritic cell-specific transmembrane protein (DC-STAMP) plays a key role in the induction of osteoclast (OC) cell fusion, as well as DC-mediated immune regulation. While DC-STAMP gene expression is upregulated in the gingival tissue with periodontitis, its pathophysiological roles in periodontitis remain unclear. To evaluate the effects of DC-STAMP in periodontitis, anti-DC-STAMP-monoclonal antibody (mAb) was tested in a mouse model of ligature-induced periodontitis ( n = 6-7/group) where Pasteurella pneumotropica ( Pp)-reactive immune response activated T cells to produce receptor activator of nuclear factor kappa-B ligand (RANKL), which, in turn, promotes the periodontal bone loss via upregulation of osteoclastogenesis. DC-STAMP was expressed on the cell surface of mature multinuclear OCs, as well as immature mononuclear OCs, in primary cultures of RANKL-stimulated bone marrow cells. Anti-DC-STAMP-mAb suppressed the emergence of large, but not small, multinuclear OCs, suggesting that DC-STAMP is engaged in the late stage of cell fusion. Anti-DC-STAMP-mAb also inhibited pit formation caused by RANKL-stimulated bone marrow cells. Attachment of ligature to a second maxillary molar induced DC-STAMP messenger RNA and protein, along with elevated tartrate-resistant acid phosphatase-positive (TRAP+) OCs and alveolar bone loss. As we expected, systemic administration of anti-DC-STAMP-mAb downregulated the ligature-induced alveolar bone loss. Importantly, local injection of anti-DC-STAMP-mAb also suppressed alveolar bone loss and reduced the total number of multinucleated TRAP+ cells in mice that received ligature attachment. Attachment of ligature induced significantly elevated tumor necrosis factor-α, interleukin-1β, and RANKL in the gingival tissue compared with the control site without ligature ( P < 0.05), which was unaffected by local injection with either anti-DC-STAMP-mAb or control-mAb. Neither in vivo anti- Pp IgG antibody nor in vitro anti- Pp T

  6. Size Effect Studies on Tensile Tests for Hot Stamping Steel

    Science.gov (United States)

    Chen, Xiaodu; Li, Yuanyuan; Han, Xianhong; Zhang, Junbo

    2018-02-01

    Tensile tests have been widely used to determine basic mechanical properties of materials. However, the properties measured may be related to geometrical factors of the tested samples especially for high-strength steels; this makes the properties' definitions and comparisons difficult. In this study, a series of tensile tests of ultra-high-strength hot-stamped steel were performed; the geometric shapes and sizes as well as the cutting direction were modified. The results demonstrate that the hot-stamped parts were isotropic and the cutting direction had no effect; the measured strengths were practically unrelated to the specimen geometries, including both size and shape. The elongations were slightly related to sample sizes within the studied range but highly depended on the sample shape, represented by the coefficient K. Such phenomena were analyzed and discussed based on microstructural observations and fracture morphologies. Moreover, two widely used elongation conversion equations, the Oliver formula and Barba's law, were introduced to verify their applicability, and a new interpolating function was developed and compared.

  7. STAMPS: development and verification of swallowing kinematic analysis software.

    Science.gov (United States)

    Lee, Woo Hyung; Chun, Changmook; Seo, Han Gil; Lee, Seung Hak; Oh, Byung-Mo

    2017-10-17

    Swallowing impairment is a common complication in various geriatric and neurodegenerative diseases. Swallowing kinematic analysis is essential to quantitatively evaluate the swallowing motion of the oropharyngeal structures. This study aims to develop a novel swallowing kinematic analysis software, called spatio-temporal analyzer for motion and physiologic study (STAMPS), and verify its validity and reliability. STAMPS was developed in MATLAB, which is one of the most popular platforms for biomedical analysis. This software was constructed to acquire, process, and analyze the data of swallowing motion. The target of swallowing structures includes bony structures (hyoid bone, mandible, maxilla, and cervical vertebral bodies), cartilages (epiglottis and arytenoid), soft tissues (larynx and upper esophageal sphincter), and food bolus. Numerous functions are available for the spatiotemporal parameters of the swallowing structures. Testing for validity and reliability was performed in 10 dysphagia patients with diverse etiologies and using the instrumental swallowing model which was designed to mimic the motion of the hyoid bone and the epiglottis. The intra- and inter-rater reliability tests showed excellent agreement for displacement and moderate to excellent agreement for velocity. The Pearson correlation coefficients between the measured and instrumental reference values were nearly 1.00 (P software is expected to be useful for researchers who are interested in the swallowing motion analysis.

  8. CO2 Laser Cutting of Hot Stamping Boron Steel Sheets

    Directory of Open Access Journals (Sweden)

    Pasquale Russo Spena

    2017-10-01

    Full Text Available This study investigates the quality of CO2 laser cutting of hot stamping boron steel sheets that are employed in the fabrication of automotive body-in-white. For this purpose, experimental laser cutting tests were conducted on 1.2 mm sheets at varying levels of laser power, cutting speed, and oxygen pressure. The resulting quality of cut edges was evaluated in terms of perpendicularity tolerance, surface irregularity, kerf width, heat affected zone, and dross extension. Experimental tests were based on a L9(34 orthogonal array design, with the effects of the process parameters on the quality responses being determined by means of a statistical analysis of variance (ANOVA. Quadratic mathematical models were developed to determine the relationships between the cutting parameters and the quality responses. Finally, a routine based on an optimization criterion was employed to predict the optimal setting of cutting factors and its effect on the quality responses. A confirmation experiment was conducted to verify the appropriateness of the optimization routine. The results show that all of the examined process parameters have a key role in determining the cut quality of hot stamping boron steel sheets, with cutting speed and their interactions having the most influencing effects. Particularly, interactions can have an opposite behavior for different levels of the process parameters.

  9. Elsa Baxter, head of the Swiss Post Office's Stamps and Philately Unit, presents to Robert Aymar, CERN's Director-General, the Swiss commemorative stamp dedicated to CERN

    CERN Multimedia

    Patrice Loiez

    2004-01-01

    'I am delighted to offer you a special stamp which commemorates your Laboratory's fifty-year history and pays tribute to its achievements, its pioneering spirit and its perseverance' said Mrs Baxter to Robert Aymar, CERN's Director-General.

  10. Bifunctional, Chemically Patterned Flat Stamps for Microcontact Printing of Polar Inks

    NARCIS (Netherlands)

    Duan, X.; Sadhu, V.B.; Perl, A.; Péter, M.; Reinhoudt, David; Huskens, Jurriaan

    2008-01-01

    Different methods to create chemically patterned, flat PDMS stamps with two different chemical functionalities were compared. The best method for making such stamps, functionalized with 1H,1H,2H,2H-perfluorodecyltrichlorosilane (PFDTS) and 3-(aminopropyl)triethoxysilane (APTS), appeared to be full

  11. 27 CFR 70.332 - Unauthorized use or sale of stamps.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Unauthorized use or sale....332 Unauthorized use or sale of stamps. Any person who buys, sells, offers for sale, uses, transfers... Code or in regulations made pursuant thereto, any stamp, coupon, ticket, book, or other device...

  12. 27 CFR 46.116 - Issuance, distribution, and examination of special tax stamps.

    Science.gov (United States)

    2010-04-01

    ... multiple locations, TTB will send to the taxpayer's principal place of business (or principal office in the... attachment to TTB Form 5630.5t required by § 46.101(b)(2). (b) Distribution of special tax stamps for... for each location listed on the attachment to TTB Form 5630.5t and that the information on each stamp...

  13. Food Stamps and Food Insecurity: What Can Be Learned in the Presence of Nonclassical Measurement Error?

    Science.gov (United States)

    Gundersen, Craig; Kreider, Brent

    2008-01-01

    Policymakers have been puzzled to observe that food stamp households appear more likely to be food insecure than observationally similar eligible nonparticipating households. We reexamine this issue allowing for nonclassical reporting errors in food stamp participation and food insecurity. Extending the literature on partially identified…

  14. Women Putting Our Stamp on America: Biographies and Activities for National Women's History Month, March 1999.

    Science.gov (United States)

    National Women's History Project, Windsor, CA.

    This booklet, intended for use by educators and by workplace and community organizers, introduces women who have been featured on U.S. postage stamps as well as a few of the women who clearly merit such honor in the future. Postage stamps featuring women have been relatively few and far between and have only skimmed the surface of U.S. women in…

  15. Determination of the interfacial heat transfer coefficient in the hot stamping of AA7075

    Directory of Open Access Journals (Sweden)

    Liu Xiaochuan

    2015-01-01

    Full Text Available The interfacial heat transfer coefficient (IHTC is a key parameter in hot stamping processes, in which a hot blank is formed and quenched by cold dies simultaneously. The IHTC should therefore be identified and used in FE models to improve the accuracy of simulation results of hot stamping processes. In this work, a hot stamping simulator was designed and assembled in a Gleeble 3800 thermo-mechanical testing system and a FE model was built in PAM-STAMP to determine the IHTC value between a hot aluminium alloy 7075 blank and cold dies. The IHTC was determined at different contact pressures under both dry and lubricated (Omega-35 conditions. In addition, a model to calculate the IHTC value at different contact pressures and area densities of lubricant was developed for the hot stamping process.

  16. Determination of the Interfacial Heat Transfer Coefficient in the Hot Stamping of AA7075

    Directory of Open Access Journals (Sweden)

    Ji Kang

    2016-01-01

    Full Text Available The interfacial heat transfer coefficient (IHTC is a key parameter in hot stamping processes, in which a hot blank is formed and quenched by cold dies simultaneously. The IHTC should therefore be identified and used in FE simulations to improve the accuracy of simulation results of hot stamping processes. In this work, a hot stamping simulator was designed and assembled in a Gleeble 3800 thermo-mechanical testing system and a FE model was built in PAM-STAMP to determine the IHTC values between a hot aluminium alloy 7075 blank and cold dies. The IHTC values were determined at different contact pressures under both dry and lubricated (Omega-35 conditions. In addition, a model to calculate the IHTC value at different contact pressures and area densities of lubricant was developed for the hot stamping process, which was proved to be working well with verification tests.

  17. A compact system for large-area thermal nanoimprint lithography using smart stamps

    International Nuclear Information System (INIS)

    Pedersen, R H; Hansen, O; Kristensen, A

    2008-01-01

    We present a simple apparatus for thermal nanoimprint lithography. In this work, the stamp is designed to significantly reduce the requirements for pressure application on the external imprint system. By MEMS-based processing, an air cavity inside the stamp is created, and the required pressure for successful imprint is reduced. Additionally, the stamp is capable of performing controlled demolding after imprint. Due to the complexity of the stamp, a compact and cost-effective imprint apparatus can be constructed. The design and fabrication of the advanced stamp as well as the simple imprint equipment is presented. Test imprints of micrometer- and nanometer-scale structures are performed and characterized with respect to uniformity across a large area (35 mm radius). State-of-the-art uniformity for µm-scale features is demonstrated

  18. Influence of preconsolidation on consolidation quality after stamp forming of C/PEEK composites

    Science.gov (United States)

    Slange, T. K.; Warnet, L.; Grouve, W. J. B.; Akkerman, R.

    2016-10-01

    Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. Currently, expensive autoclave and press consolidation are used to preconsolidate blanks. This study investigates the influence of preconsolidation on final consolidation quality after stamp forming and explores the potential of alternative blank manufacturing methods that could reduce part costs. Blanks were manufactured using various blank manufacturing methods and subsequently were stamp formed. The consolidation quality both before and after stamp forming was compared, where the focus was on void content as the main measure for consolidation quality. The void content was characterized through thickness and density measurements, as well as by microscopy analysis. Results indicate that preconsolidation quality does have an influence on the final consolidation quality. This is due to the severe deconsolidation and limited reconsolidation during stamp forming. Nevertheless, the potential of automated fiber placement and ultrasonic spot welding as alternative blank manufacturing methods was demonstrated.

  19. Establishing monitoring programs for travel time reliability. [supporting datasets

    Science.gov (United States)

    2014-01-01

    The objective of this project was to develop system designs for programs to monitor travel time reliability and to prepare a guidebook that practitioners and others can use to design, build, operate, and maintain such systems. Generally, such travel ...

  20. Finite element analysis and optimization of process parameters during stamp forming of composite materials

    International Nuclear Information System (INIS)

    Venkatesan, S; Kalyanasundaram, S

    2010-01-01

    In the manufacture of parts for high performance structures using composite materials, the quality and robustness of the parts is of utmost importance. The quality of the produced parts depends largely on the process parameters and manufacturing methodologies. This study presents the use of a temperature dependant orthotropic material for a coupled structural-thermal analysis of the stamp forming process. The study investigated the effects of process parameters such as pre-heat temperature, blank holder force and process time on the formability of composite materials. Temperature was found to be the dominant factor governing the formability of the composite material while higher blank holder forces were deemed to be important for achieving high quality of the parts manufactured. Finally, an optimum set of parameters was used to compare the simulations with experimental results using an optical strain measurement system.

  1. A Fully Integrated Humidity Sensor System-on-Chip Fabricated by Micro-Stamping Technology

    Science.gov (United States)

    Huang, Che-Wei; Huang, Yu-Jie; Lu, Shey-Shi; Lin, Chih-Ting

    2012-01-01

    A fully integrated humidity sensor chip was designed, implemented, and tested. Utilizing the micro-stamping technology, the pseudo-3D sensor system-on-chip (SSoC) architecture can be implemented by stacking sensing materials directly on the top of a CMOS-fabricated chip. The fabricated sensor system-on-chip (2.28 mm × 2.48 mm) integrated a humidity sensor, an interface circuit, a digital controller, and an On-Off Keying (OOK) wireless transceiver. With low power consumption, i.e., 750 μW without RF operation, the sensitivity of developed sensor chip was experimentally verified in the relative humidity (RH) range from 32% to 60%. The response time of the chip was also experimentally verified to be within 5 seconds from RH 36% to RH 64%. As a consequence, the implemented humidity SSoC paves the way toward the an ultra-small sensor system for various applications.

  2. State Space Methods for Timed Petri Nets

    DEFF Research Database (Denmark)

    Christensen, Søren; Jensen, Kurt; Mailund, Thomas

    2001-01-01

    it possible to condense the usually infinite state space of a timed Petri net into a finite condensed state space without loosing analysis power. The second method supports on-the-fly verification of certain safety properties of timed systems. We discuss the application of the two methods in a number......We present two recently developed state space methods for timed Petri nets. The two methods reconciles state space methods and time concepts based on the introduction of a global clock and associating time stamps to tokens. The first method is based on an equivalence relation on states which makes...

  3. Intelligent Flight Support System (IFSS): A Real-time Intelligent Decision Support Prototype, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The integration of the analysis tools with the advanced visualization capabilities in The Intelligent Flight Support System (IFSS) can provide a unique method for...

  4. Fabrication of Ni stamp with high aspect ratio, two-leveled, cylindrical microstructures using dry etching and electroplating

    DEFF Research Database (Denmark)

    Petersen, Ritika Singh; Keller, Stephan Sylvest; Hansen, Ole

    2015-01-01

    obtained by defining a reservoir and a separating trench with different depths of 85 and 125 μm, respectively, in a single embossing step. The fabrication of the required two leveled stamp is done using a modified DEEMO (dry etching, electroplating and molding) process. Dry etching using the Bosch process...... and electroplating are optimized to obtain a stamp with smooth stamp surfaces and a positive sidewall profile. Using this stamp, hot embossing is performed successfully with excellent yield and high replication fidelity....

  5. A Path-Independent Forming Limit Criterion for Stamping Simulations

    International Nuclear Information System (INIS)

    Zhu Xinhai; Chappuis, Laurent; Xia, Z. Cedric

    2005-01-01

    Forming Limit Diagram (FLD) has been proved to be a powerful tool for assessing necking failures in sheet metal forming analysis for majority of stamping operations over the last three decades. However, experimental evidence and theoretical analysis suggest that its applications are limited to linear or almost linear strain paths during its deformation history. Abrupt changes or even gradual deviations from linear strain-paths will shift forming limit curves from their original values, a situation that occurs in vast majority of sequential stamping operations such as where the drawing process is followed by flanging and re-strike processes. Various forming limit models have been put forward recently to provide remedies for the problem, noticeably stress-based and strain gradient-based forming limit criteria. This study presents an alternative path-independent forming limit criterion. Instead of traditional Forming Limit Diagrams (FLD) which are constructed in terms of major - minor principal strains throughout deformation history, the new criterion defines a critical effective strain ε-bar* as the limit strain for necking, and it is shown that ε-bar* can be expressed as a function of current strain rate state and material work hardening properties, without the need of explicitly considering strain-path effects. It is given by ε-bar* = f(β, k, n) where β = (dε 2 /dε 1 ) at current deformation state, and k and n are material strain hardening parameters if a power law is assumed. The analysis is built upon previous work by Storen and Rice [1975] and Zhu et al [2002] with the incorporation of anisotropic yield models such as Hill'48 for quadratic orthotropic yield and Hill'79 for non-quadratic orthotropic yield. Effects of anisotropic parameters such as R-values and exponent n-values on necking are investigated in detail for a variety of strain paths. Results predicted according to current analysis are compared against experimental data gathered from literature

  6. Time, Interaction, and Design in Support of a Good Life

    DEFF Research Database (Denmark)

    Froes, Isabel Cristina G.; Laaksolahti, Jarmo Matti; Witzner Hansen, Dan

    development. Our ongoing investigation of Interaction Design for a Good Life (http://itu.dk/IxDLab/) has uncovered a broad diversity of perspectives on how to unpack ‘a good life’ through research and design, and indeed what constitutes a good life to begin with. Through our investigations, time has surfaced...... as pivotal to our budding understanding of elements of a good life and a useful framing for future investigations. Time is also an important topic for interaction design, because it is at the core of interaction, the practice of design, and, in many ways, our use and relationships with technological......This position paper outlines a research program for the IxD Research Group at the IT University of Copenhagen. As such, it presents a range of questions addressing different corners of the question of time in IxD from the point of view of HCI, social interaction, material expressions, and software...

  7. Enhancing Time Synchronization Support in Wireless Sensor Networks

    Science.gov (United States)

    Tavares Bruscato, Leandro; Heimfarth, Tales; Pignaton de Freitas, Edison

    2017-01-01

    With the emerging Internet of Things (IoT) technology becoming reality, a number of applications are being proposed. Several of these applications are highly dependent on wireless sensor networks (WSN) to acquire data from the surrounding environment. In order to be really useful for most of applications, the acquired data must be coherent in terms of the time in which they are acquired, which implies that the entire sensor network presents a certain level of time synchronization. Moreover, to efficiently exchange and forward data, many communication protocols used in WSN rely also on time synchronization among the sensor nodes. Observing the importance in complying with this need for time synchronization, this work focuses on the second synchronization problem, proposing, implementing and testing a time synchronization service for low-power WSN using low frequency real-time clocks in each node. To implement this service, three algorithms based on different strategies are proposed: one based on an auto-correction approach, the second based on a prediction mechanism, while the third uses an analytical correction mechanism. Their goal is the same, i.e., to make the clocks of the sensor nodes converge as quickly as possible and then to keep them most similar as possible. This goal comes along with the requirement to keep low energy consumption. Differently from other works in the literature, the proposal here is independent of any specific protocol, i.e., it may be adapted to be used in different protocols. Moreover, it explores the minimum number of synchronization messages by means of a smart clock update strategy, allowing the trade-off between the desired level of synchronization and the associated energy consumption. Experimental results, which includes data acquired from simulations and testbed deployments, provide evidence of the success in meeting this goal, as well as providing means to compare these three approaches considering the best synchronization

  8. Enhancing Time Synchronization Support in Wireless Sensor Networks.

    Science.gov (United States)

    Tavares Bruscato, Leandro; Heimfarth, Tales; Pignaton de Freitas, Edison

    2017-12-20

    With the emerging Internet of Things (IoT) technology becoming reality, a number of applications are being proposed. Several of these applications are highly dependent on wireless sensor networks (WSN) to acquire data from the surrounding environment. In order to be really useful for most of applications, the acquired data must be coherent in terms of the time in which they are acquired, which implies that the entire sensor network presents a certain level of time synchronization. Moreover, to efficiently exchange and forward data, many communication protocols used in WSN rely also on time synchronization among the sensor nodes. Observing the importance in complying with this need for time synchronization, this work focuses on the second synchronization problem, proposing, implementing and testing a time synchronization service for low-power WSN using low frequency real-time clocks in each node. To implement this service, three algorithms based on different strategies are proposed: one based on an auto-correction approach, the second based on a prediction mechanism, while the third uses an analytical correction mechanism. Their goal is the same, i.e., to make the clocks of the sensor nodes converge as quickly as possible and then to keep them most similar as possible. This goal comes along with the requirement to keep low energy consumption. Differently from other works in the literature, the proposal here is independent of any specific protocol, i.e., it may be adapted to be used in different protocols. Moreover, it explores the minimum number of synchronization messages by means of a smart clock update strategy, allowing the trade-off between the desired level of synchronization and the associated energy consumption. Experimental results, which includes data acquired from simulations and testbed deployments, provide evidence of the success in meeting this goal, as well as providing means to compare these three approaches considering the best synchronization

  9. Time series patterns and language support in DBMS

    Science.gov (United States)

    Telnarova, Zdenka

    2017-07-01

    This contribution is focused on pattern type Time Series as a rich in semantics representation of data. Some example of implementation of this pattern type in traditional Data Base Management Systems is briefly presented. There are many approaches how to manipulate with patterns and query patterns. Crucial issue can be seen in systematic approach to pattern management and specific pattern query language which takes into consideration semantics of patterns. Query language SQL-TS for manipulating with patterns is shown on Time Series data.

  10. Integrated Stamping Simulation Using State Of The Art Techniques To Fulfill Quality Assessment Requirements

    International Nuclear Information System (INIS)

    Ling, David; Lambriks, Marc; El Khaldi, Fouad

    2005-01-01

    The last few years have seen the use of stamping simulation evolve to the extent that it is now a mainstream activity; a core part of the press tool engineering process. Now, new requirements for the use of challenging materials like Dual phase / Complex phase steel, VHSS, and aluminum, together with more stringent quality expectations, and shorter development cycles, there is a need to assess the panel quality in a wider context, before committing to tool manufacture.The integrated approach from ESI Group allows early up-front feasibility assessment, geometry and process optimization, and detailed process validation all within one system. Rapid die design and quick forming simulation modules play an essential role in the early stages of the process. A seamless connection between simulation and geometry is a vital characteristic, with the accurate simulation being used to validate and fine tune the process in order to assess final component quality in unprecedented detail, utilizing some of the most accurate material models available today. The combination of the distributed memory processing (DMP) solver together with new cost effective cluster based compute servers provide a practical solution to the problems of 'one million element' model sizes, and more sophisticated modeling methodologies become realistic for the first time.It is no longer sufficient to merely focus on the draw die, forming simulation must now consider the entire die line up. Typically, around half of forming issues arise from the draw die, so the time has now come to address the other half as well! This paper will discuss how the PAM-STAMP 2G TM integrated solution is successfully used to deliver a positive business impact, by providing virtual panel quality assessment, tolerance control, and springback compensation. The paper will also discuss how other forming processes can be accurately modeled using the new modules

  11. Supporting Quality Timely PhD Completions: Delivering Research Outcomes

    Science.gov (United States)

    Gasson, Susan

    2015-01-01

    The case study used a three-phase organising process to explain how design and implementation of an accessible and interactive electronic thesis submission form streamlined quality assurance of theses and their timely dissemination via an online thesis repository. The quality of the theses submitted is assured by key academics in their final sign…

  12. Titanium nitride stamps replicating nanoporous anodic alumina films

    International Nuclear Information System (INIS)

    Navas, D; Sanchez, O; Asenjo, A; Jaafar, M; Baldonedo, J L; Vazquez, M; Hernandez-Velez, M

    2007-01-01

    Fabrication of nanostructured TiN films by magnetron sputtering using nanoporous anodic alumina films (NAAF) as substrates is reported. These hard nanostructured films could be used for pre-patterning aluminium foils and to obtain nanoporous films replicating the starting NAAF over a wide range of pore diameters and spacings. Pre-patterned Al foils are obtained by compression with pressures lower than those previously reported, then a new NAAF can be fabricated by means of only one anodization process. As an example, one of the TiN stamps was used for pre-patterning an Al foil at a pressure of 200 kg cm -2 and then it was anodized in oxalic acid solution obtaining the corresponding replica of the starting NAAF

  13. LOGIC SIMULATION OF LIFE SUPPORT SYSTEM COMPONENT IN REAL TIME

    Directory of Open Access Journals (Sweden)

    A. S. Marchenko

    2016-01-01

    Full Text Available Abstract. The article proposed the use of simulation methods for evaluating the effectiveness of a stepped fan engine speed control while maintaining the air flow volume in the set boundaries of the «fan-filter» system. A detailed algorithm of the program made on the basis of an Any Logic software package. Is analyzed the possibility of using the proposed method in the design of ventilation systems.The proposed method allows at the design stage to determine the maximum replacement intervals of the systems filter elements, as well as to predict the time to switch the fan motor speeds. Using of the technique allows to refuse the complex air flow systems and maximize the life of the filter elements set.Methods of logical processes modeling allows to reduce construction costs and improve energy efficiency of buildings. 

  14. Analysis of roll-stamped light guide plate fabricated with laser-ablated stamper

    Science.gov (United States)

    Na, Hyunjun; Hong, Seokkwan; Kim, Jongsun; Hwang, Jeongho; Joo, Byungyun; Yoon, Kyunghwan; Kang, Jeongjin

    2017-12-01

    LGP (light guide plate) is one of the major components of LCD (liquid crystal display), and it makes surface illumination for LCD backlit. LGP is a transparent plastic plate usually produced by injection molding process. On the back of LGP there are micron size patterns for extraction of light. Recently a roll-stamping process has achieved the high mass productivity of thinner LGPs. In order to fabricate optical patterns on LGPs, a fabricating tool called as a stamper is used. Micro patterns on metallic stampers are made by several micro machining processes such as chemical etching, LIGA-reflow, and laser ablation. In this study, a roll-stamping process by using a laser ablated metallic stamper was dealt with in consideration of the compatibility with the roll-stamping process. LGP fabricating tests were performed using a roll-stamping process with four different roll pressures. Pattern shapes on the stamper fabricated by laser ablation and transcription ratios of the roll-stamping process were analyzed, and LGP luminance was evaluated. Based on the evaluation, optical simulation model for LGP was made and simulation accuracy was evaluated. Simulation results showed good agreements with optical performance of LGPs in the brightness and uniformity. It was also shown that the roll-stamped LGP has the possibility of better optical performance than the conventional injection molded LGP. It was also shown that the roll-stamped LGP with the laser ablated stamper is potential to have better optical performance than the conventional injection molded LGP.

  15. Resistless Fabrication of Nanoimprint Lithography (NIL Stamps Using Nano-Stencil Lithography

    Directory of Open Access Journals (Sweden)

    Juergen Brugger

    2013-10-01

    Full Text Available In order to keep up with the advances in nano-fabrication, alternative, cost-efficient lithography techniques need to be implemented. Two of the most promising are nanoimprint lithography (NIL and stencil lithography. We explore here the possibility of fabricating the stamp using stencil lithography, which has the potential for a cost reduction in some fabrication facilities. We show that the stamps reproduce the membrane aperture patterns within ±10 nm and we validate such stamps by using them to fabricate metallic nanowires down to 100 nm in size.

  16. Limited indications of tax stamp discordance and counterfeiting on cigarette packs purchased in tobacco retailers, 97 counties, USA, 2012.

    Science.gov (United States)

    Lee, Joseph G L; Golden, Shelley D; Ribisl, Kurt M

    2017-12-01

    Increasing the per-unit cost of tobacco products is one of the strongest interventions for tobacco control. In jurisdictions with higher taxes in the U.S., however, cigarette pack litter studies show a substantial proportion of littered packs lack the appropriate tax stamp. More limited but still present counterfeiting also exists. We sought to examine the role of tobacco retailers as a source for untaxed and counterfeit products. Data collectors purchased Newport Green (menthol) or Marlboro Red cigarette packs in a national probability-based sample of tobacco retailers (in 97 counties) from June-October 2012. They made no effort to buy counterfeit or untaxed cigarettes. In this cross-sectional study, we assessed the presence, tax authority, and type (low-tech thermal vs. encrypted) of cigarette pack tax stamps; concordance of tax stamps with where the pack was purchased; and, for Marlboro cigarettes, publicly available visible indicators of counterfeiting. We purchased 2147 packs of which 2033 had tax stamps. Packs missing stamps were in states that do not require them. We found very limited discordance between store location and tax stamp(s) (tax stamps (13%). This occurred entirely with low-tech tax stamps and was not identified with encrypted tax stamps. We found no clear evidence of counterfeit products. Almost all tax stamps matched the location of purchase. Litter studies may be picking up legal tax avoidance instead of illegal tax evasion or, alternatively, purchase of illicit products requires special request by the purchaser.

  17. Direct stamping of silver nanoparticles toward residue-free thick electrode

    Directory of Open Access Journals (Sweden)

    Jiseok Kim, Kevin Wubs, Byeong-Soo Bae and Woo Soo Kim

    2012-01-01

    Full Text Available Direct stamping of functional materials has been developed for cost-effective and process-effective manufacturing of nano/micro patterns. However, there remain several challenging issues like the perfect removal of the residual layer and realization of high aspect ratio. We have demonstrated facile fabrication of flexible strain sensors that have microscale thick interdigitated capacitors with no residual layer by a simple direct stamping with silver nanoparticles (AgNPs. Polyurethane (PU prepolymer was utilized as an adhesive layer to transfer AgNPs more efficiently during the separation step of the flexible stamp from directly stamped AgNPs. Scanning electron microscopy images and energy dispersive x-ray spectroscopy analysis revealed residue-free transfer of microscale thick interdigitated electrodes onto two different flexible substrates (elastomeric and brittle for the application to highly sensitive strain sensors.

  18. STAMP model and its application prospect in DCS safety analysis of nuclear power plant

    International Nuclear Information System (INIS)

    Yang Xiaohua; Liu Jie; Liu Zhaohui; Liu Hua; Yu Tonglan

    2013-01-01

    The application of DCS (Digit Control System) is a certain trend for the development of nuclear power. DCS not only improves the control capability of nuclear power system, but also increases the complexity of the system. Traditional safety analysis techniques based on event-chain model are facing challenges. In order to improve the safety performance of nuclear power DCS, the latest research achievement in the field of safety engineering should be focused, studied and applied into nuclear power safety. This paper introduces a new safety analysis model named STAMP (Systems-Theoretic Accident Modeling and Processes) based on the system theory, analyzes its advantages and disadvantages compared with the traditional ones, and explains the basic steps of STPA (STAMP-Based Hazard Analysis) technology. Finally, according to the application status of STAMP at home and abroad, it prospects the development of STAMP in China's nuclear power safety. (authors)

  19. 49 CFR 238.119 - Rim-stamped straight-plate wheels.

    Science.gov (United States)

    2010-10-01

    ... input to the wheel during braking. (b) A rim-stamped straight-plate wheel shall not be used as a... that is periodically tread-braked for a short duration by automatic circuitry for the sole purpose of...

  20. 26 CFR 301.7209-1 - Unauthorized use or sale of stamps.

    Science.gov (United States)

    2010-04-01

    ..., transfers, takes or gives in exchange, or pledges or gives in pledge, except as authorized in the Code or in regulations made pursuant thereto, any stamp, coupon, ticket, book, or other device prescribed by the...

  1. Social support and social norms: do both contribute to predicting leisure-time exercise?

    Science.gov (United States)

    Okun, Morris A; Ruehlman, Linda; Karoly, Paul; Lutz, Rafer; Fairholme, Chris; Schaub, Rachel

    2003-01-01

    To clarify the contribution of social support and social norms to exercise behavior. A sample of 363 college students completed a questionnaire that assessed social support and social negativity from friends, descriptive and injunctive social norms related to friends, perceived behavioral control, attitude, intention, and leisure-time exercise. Esteem social support was the strongest predictor of total and strenuous leisure-time exercise (P leisure-time exercise. Social support and social norms contribute independently to our understanding of variation in the frequency of strenuous leisure-time exercise.

  2. EFFECTS OF EBT CUSTOMER SERVICE WAIVERS ON FOOD STAMP RECIPIENTS: EXECUTIVE SUMMARY

    OpenAIRE

    Kirlin, John A.; Logan, Christopher

    2002-01-01

    Most State agencies are now using electronic benefits transfer (EBT) systems to issue food stamp benefits. To promote operational efficiency, some States have received waivers of certain rules governing EBT use. An exploratory study was conducted to ascertain the effects of these waivers on food stamp recipients. The results show that two of the waivers-those allowing recipients to select their own personal identification numbers and to receive EBT training by mail rather than in person-cause...

  3. Springback Prediction, Compensation and Correlation for Automotive Stamping

    International Nuclear Information System (INIS)

    Xu Siguang; Zhao Kunmin; Lanker, Terry; Zhang, Jimmy; Wang, C.T.

    2005-01-01

    To reduce weight and increase fuel efficiency and safety, more and more automotive sheet stamping parts are being made of aluminum and high strength steels. Forming of such materials encounters not just reduced formability but also dimensional quality problems. Springback prediction accuracy and compensation effectiveness have been the major challenge to die development, construction and tryout. In this paper, the factors that affect the accuracy of springback prediction are discussed, which includes the effect of material models, the selection of element size, and the contact algorithms. Springback predictions of several automotive aluminum and high strength panels are compared with measurement data. The examples show that the prediction correlates with measurement data in both springback trend and magnitude. The effect of springback on final product can be reduced or eliminated through process control and die face compensation. The process control method involves finding the root causes of springback and eliminating them through process modification. The geometrical compensation of die surface is a direct way to eliminate the springback effect. The global scaling compensation method is normally limited to parts with relatively small springback. For large springback and twisting, a new approach is discussed, which takes into account of the effect of deformation and springback history. The compensation is achieved iteratively by solving a system of non-linear equations. Production dies were cut to the compensated surface, which shows that the die compensation is an efficient way to reduce springback-induced geometry deviation

  4. Carbon nanotube substrates and catalyzed hot stamp for polishing and patterning the substrates

    Science.gov (United States)

    Wang, Yuhuang [Evanston, IL; Hauge, Robert H [Houston, TX; Schmidt, Howard K [Houston, TX; Kim, Myung Jong [Houston, TX; Kittrell, W Carter [Houston, TX

    2009-09-08

    The present invention is generally directed to catalyzed hot stamp methods for polishing and/or patterning carbon nanotube-containing substrates. In some embodiments, the substrate, as a carbon nanotube fiber end, is brought into contact with a hot stamp (typically at 200-800.degree. C.), and is kept in contact with the hot stamp until the morphology/patterns on the hot stamp have been transferred to the substrate. In some embodiments, the hot stamp is made of material comprising one or more transition metals (Fe, Ni, Co, Pt, Ag, Au, etc.), which can catalyze the etching reaction of carbon with H.sub.2, CO.sub.2, H.sub.2O, and/or O.sub.2. Such methods can (1) polish the carbon nanotube-containing substrate with a microscopically smooth finish, and/or (2) transfer pre-defined patterns from the hot stamp to the substrate. Such polished or patterned carbon nanotube substrates can find application as carbon nanotube electrodes, field emitters, and field emitter arrays for displays and electron sources.

  5. A Fully Automated and Robust Method to Incorporate Stamping Data in Crash, NVH and Durability Analysis

    Science.gov (United States)

    Palaniswamy, Hariharasudhan; Kanthadai, Narayan; Roy, Subir; Beauchesne, Erwan

    2011-08-01

    Crash, NVH (Noise, Vibration, Harshness), and durability analysis are commonly deployed in structural CAE analysis for mechanical design of components especially in the automotive industry. Components manufactured by stamping constitute a major portion of the automotive structure. In CAE analysis they are modeled at a nominal state with uniform thickness and no residual stresses and strains. However, in reality the stamped components have non-uniformly distributed thickness and residual stresses and strains resulting from stamping. It is essential to consider the stamping information in CAE analysis to accurately model the behavior of the sheet metal structures under different loading conditions. Especially with the current emphasis on weight reduction by replacing conventional steels with aluminum and advanced high strength steels it is imperative to avoid over design. Considering this growing need in industry, a highly automated and robust method has been integrated within Altair Hyperworks® to initialize sheet metal components in CAE models with stamping data. This paper demonstrates this new feature and the influence of stamping data for a full car frontal crash analysis.

  6. Cooling Systems Design in Hot Stamping Tools by a Thermal-Fluid-Mechanical Coupled Approach

    Directory of Open Access Journals (Sweden)

    Tao Lin

    2014-06-01

    Full Text Available Hot stamping tools with cooling systems are the key facilities for hot stamping process of Ultrahigh strength steels (UHSS in automotive industry. Hot stamping tools have significant influence on the final microstructure and properties of the hot stamped parts. In serials production, the tools should be rapidly cooled by cooling water. Hence, design of hot stamping tools with cooling systems is important not only for workpieces of good quality but also for the tools with good cooling performance and long life. In this paper, a new multifield simulation method was proposed for the design of hot stamping tools with cooling system. The deformation of the tools was also analyzed by this method. Based on MpCCI (Mesh-based parallel Code Coupling Interface, thermal-fluid simulation and thermal-fluid-mechanical coupled simulation were performed. Subsequently, the geometrical parameters of the cooling system are investigated for the design. The results show that, both the distance between the ducts and the distance between the ducts and the tools loaded contour have significant influence on the quenching effect. And better quenching effect can be achieved with the shorter distance from the tool surface and with smaller distance between ducts. It is also shown that, thermal expansion is the main reason for deformation of the hot forming tools, which causes the distortion of the cooling ducts, and the stress concentration at corner of the ducts.

  7. Run-time middleware to support real-time system scenarios

    NARCIS (Netherlands)

    Goossens, K.; Koedam, M.; Sinha, S.; Nelson, A.; Geilen, M.

    2015-01-01

    Systems on Chip (SOC) are powerful multiprocessor systems capable of running multiple independent applications, often with both real-time and non-real-time requirements. Scenarios exist at two levels: first, combinations of independent applications, and second, different states of a single

  8. The Study on Weldability of Boron Steel and Hot-Stamped Steel by Using Laser Heat Source (Ⅲ) - Comparison on Laser Weldability of Boron Steel and Hot -Stamped Steel-

    Energy Technology Data Exchange (ETDEWEB)

    Choi, So Young; Kim, Jong Do [Korea Maritime and Ocean University, Busan (Korea, Republic of); Kim, Jong Su [Korea Institute of Machinery and Materials, Daejeon (Korea, Republic of)

    2015-01-15

    This study was conducted to compare the laser weldability of boron steel and hot-stamped steel. In general, boron steel is used in the hot-stamping process. Hot-stamping is a method for simultaneously forming and cooling boron steel in a press die after heating it to the austenitizing temperature. Hot-stamped steel has a strength of 1500 MPa or more. Thus, in this study, the laser weldability of boron steel and that of hot-stamped steel were investigated and compared. A continuous wave disk laser was used to produce butt and lap joints. In the butt welding, the critical cooling speed at which full penetration was obtained in the hot-stamped steel was lower than that of boron steel. In the lap welding, the joint widths were similar regardless of the welding speed when full penetration was obtained.

  9. The Study on Weldability of Boron Steel and Hot-Stamped Steel by Using Laser Heat Source (Ⅲ) - Comparison on Laser Weldability of Boron Steel and Hot -Stamped Steel-

    International Nuclear Information System (INIS)

    Choi, So Young; Kim, Jong Do; Kim, Jong Su

    2015-01-01

    This study was conducted to compare the laser weldability of boron steel and hot-stamped steel. In general, boron steel is used in the hot-stamping process. Hot-stamping is a method for simultaneously forming and cooling boron steel in a press die after heating it to the austenitizing temperature. Hot-stamped steel has a strength of 1500 MPa or more. Thus, in this study, the laser weldability of boron steel and that of hot-stamped steel were investigated and compared. A continuous wave disk laser was used to produce butt and lap joints. In the butt welding, the critical cooling speed at which full penetration was obtained in the hot-stamped steel was lower than that of boron steel. In the lap welding, the joint widths were similar regardless of the welding speed when full penetration was obtained

  10. Towards RTOS support for mixed time-triggered and event-triggered task sets

    NARCIS (Netherlands)

    Heuvel, van den M.M.H.P.; Bril, R.J.; Lukkien, J.J.; Isovic, D.; Sankar Ramachandran, G.

    2012-01-01

    Many embedded systems have complex timing constraints and, at the same time, have flexibility requirements which prohibit offline planning of the entire system. To support a mixture of time-triggered and event-triggered tasks, some industrial systems deploy a real-time operating system (RTOS) with a

  11. A Human Sensor Network Framework in Support of Near Real Time Situational Geophysical Modeling

    Science.gov (United States)

    Aulov, O.; Price, A.; Smith, J. A.; Halem, M.

    2013-12-01

    The area of Disaster Management is well established among Federal Agencies such as FEMA, EPA, NOAA and NASA. These agencies have well formulated frameworks for response and mitigation based on near real time satellite and conventional observing networks for assimilation into geophysical models. Forecasts from these models are used to communicate with emergency responders and the general public. More recently, agencies have started using social media to broadcast warnings and alerts to potentially affected communities. In this presentation, we demonstrate the added benefits of mining and assimilating the vast amounts of social media data available from heterogeneous hand held devices and social networks into established operational geophysical modeling frameworks as they apply to the five cornerstones of disaster management - Prevention, Mitigation, Preparedness, Response and Recovery. Often, in situations of extreme events, social media provide the earliest notification of adverse extreme events. However, various forms of social media data also can provide useful geolocated and time stamped in situ observations, complementary to directly sensed conventional observations. We use the concept of a Human Sensor Network where one views social media users as carrying field deployed "sensors" whose posts are the remotely "sensed instrument measurements.' These measurements can act as 'station data' providing the resolution and coverage needed for extreme event specific modeling and validation. Here, we explore the use of social media through the use of a Human Sensor Network (HSN) approach as another data input source for assimilation into geophysical models. Employing the HSN paradigm can provide useful feedback in near real-time, but presents software challenges for rapid access, quality filtering and transforming massive social media data into formats consistent with the operational models. As a use case scenario, we demonstrate the value of HSN for disaster management

  12. Tribological performances of new steel grades for hot stamping tools

    Science.gov (United States)

    Medea, F.; Venturato, G.; Ghiotti, A.; Bruschi, S.

    2017-09-01

    In the last years, the use of High Strength Steels (HSS) as structural parts in car body-in-white manufacturing has rapidly increased thanks to their favourable strength-to-weight ratio and stiffness, which allow a reduction of the fuel consumption to accommodate the new restricted regulations for CO2 emissions control. The survey of the technical and scientific literature shows a large interest in the development of different coatings for the blanks from the traditional Al-Si up to new Zn-based coatings and on the analysis of hard PVD, CVD coatings and plasma nitriding applied on the tools. By contrast, fewer investigations have been focused on the development and test of new tools steels grades capable to improve the wear resistance and the thermal properties that are required for the in-die quenching during forming. On this base, the paper deals with the analysis and comparison the tribological performances in terms of wear, friction and heat transfer of new tool steel grades for high-temperature applications, characterized by a higher thermal conductivity than the commonly used tools. Testing equipment, procedures as well as measurements analyses to evaluate the friction coefficient, the wear and heat transfer phenomena are presented. Emphasis is given on the physical simulation techniques that were specifically developed to reproduce the thermal and mechanical cycles on the metal sheets and dies as in the industrial practice. The reference industrial process is the direct hot stamping of the 22MnB5 HSS coated with the common Al-Si coating for automotive applications.

  13. Diversity of Physicians’ Handwriting and Name Stamp in Chemotherapy Prescriptions: Potential Target for Fraud

    Directory of Open Access Journals (Sweden)

    Asiyeh Amouei

    2018-02-01

    Full Text Available BBackgrounds: Verification and authentication of the paper-based handwritten prescriptions is of great importance for antineoplastic medications that are good targets for forgery and fraud. Pharmacists usually investigate handwriting, signature and name stamp of prescribers to verify prescriptions in Iran. Anecdotal reports of variations in handwriting and name stamp of physicians who wrote antineoplastic prescriptions raised concerns in this regard. The aim of the study was to investigate the reported diversity and evaluate the quality of writing physician identity and required items in antineoplastic prescriptions.Methods: All insured hand-written prescriptions contained at least one antineoplastic medication and were dispensed by four main authorized community pharmacies dispensing antineoplastic medications in Tehran during one month were included. Prescriptions that were written by specialties other than oncology-related fields were excluded. Prescriptions of each physician were evaluated considering handwriting and name stamp by experienced pharmacy staff and the frequency of detected handwriting and name stamp types was recorded.Results: Of the 11022 included prescriptions, 10944 were eligible and written by 241 physicians. Median (third quartile number of physicians’ prescriptions was 17 (51. Maximum number of observed handwriting and name stamp types were eight and six respectively. High prescribers tended to have several handwriting and name stamp types.Conclusion: The observed diversity and variation in handwriting and name stamp of the physicians in antineoplastic prescriptions may facilitate the entrance of forged prescription and makes fraud detection difficult. Administrative and regulatory interventions in addition to notification of health care professionals about the observed potential might be necessary.

  14. Fabrication of a Ni nano-imprint stamp for an anti-reflective layer using an anodic aluminum oxide template.

    Science.gov (United States)

    Park, Eun-Mi; Lim, Seung-Kyu; Ra, Senug-Hyun; Suh, Su-Jung

    2013-11-01

    Aluminum anodizing can alter pore diameter, density distribution, periodicity and layer thickness in a controlled way. Because of this property, porous type anodic aluminum oxide (AAO) was used as a template for nano-structure fabrication. The alumina layer generated at a constant voltage increased the pore size from 120 nm to 205 nm according to an increasing process time from 60 min to 150 min. The resulting fabricated AAO templates had pore diameters at or less than 200 nm. Ni was sputtered as a conductive layer onto this AAO template and electroplated using DC and pulse power. Comparing these Ni stamps, those generated from electroplating using on/reverse/off pulsing had an ordered pillar array and maintained the AAO template morphology. This stamp was used for nano-imprinting on UV curable resin coated glass wafer. Surface observations via electron microscopy showed that the nano-imprinted patterned had the same shape as the AAO template. A soft mold was subsequently fabricated and nano-imprinted to form a moth-eye structure on the glass wafer. An analysis of the substrate transmittance using UV-VIS/NIR spectroscopy showed that the transmittance of the substrate with the moth-eye structure was 5% greater that the non-patterned substrate.

  15. Improving the Quality of Hot Stamping Parts with Innovative Press Technology and Inline Process Control

    Science.gov (United States)

    Vollmer, R.; Palm, C.

    2017-09-01

    The increasing number of hot stamped parts in the automotive industry is challenging different process areas. This paper presents a method how to improve the production rates over the whole life cycle of a hot forming part. In the core element of a hot forming line, the hydraulic press, mainly two processing steps are performed. Forming and quenching of the sheet metal part. In addition to the forming operation, it is inevitable to optimize the quenching condition in the bottom dead centre in order to reach a fully martensitic structure and tight geometrical tolerances of the part. Deviations in the blank thickness, tool wear, polishing of classical tools impair the quenching condition and therefore the part quality over the time. A new press and tool design has been developed to counter this effect by providing homogenous contact pressure over the whole die. Especially with a multi cavity tool, the new method is advantageous. Test series have shown that the new tool and press concept can produce parts with a blank thickness of 1.0 mm within 8.0 s cycle time. The so called PCH flex principle makes it possible to produce such high output rates under reliable conditions.

  16. Development of a support software system for real-time HAL/S applications

    Science.gov (United States)

    Smith, R. S.

    1984-01-01

    Methodologies employed in defining and implementing a software support system for the HAL/S computer language for real-time operations on the Shuttle are detailed. Attention is also given to the management and validation techniques used during software development and software maintenance. Utilities developed to support the real-time operating conditions are described. With the support system being produced on Cyber computers and executable code then processed through Cyber or PDP machines, the support system has a production level status and can serve as a model for other software development projects.

  17. Validation Support for Distributed Real-Time Embedded Systems in VDM++

    DEFF Research Database (Denmark)

    S. Fitzgerald, John; Gorm Larsen, Peter; Tjell, Simon

    2007-01-01

    We present a tool-supported approach to the validation of system-level timing properties in formal models of distributed real-time embedded systems. Our aim is to provide system architects with rapid feedback on the timing characteristics of alternative designs in the often volatile early stages ...

  18. Phase Space Prediction of Chaotic Time Series with Nu-Support Vector Machine Regression

    International Nuclear Information System (INIS)

    Ye Meiying; Wang Xiaodong

    2005-01-01

    A new class of support vector machine, nu-support vector machine, is discussed which can handle both classification and regression. We focus on nu-support vector machine regression and use it for phase space prediction of chaotic time series. The effectiveness of the method is demonstrated by applying it to the Henon map. This study also compares nu-support vector machine with back propagation (BP) networks in order to better evaluate the performance of the proposed methods. The experimental results show that the nu-support vector machine regression obtains lower root mean squared error than the BP networks and provides an accurate chaotic time series prediction. These results can be attributable to the fact that nu-support vector machine implements the structural risk minimization principle and this leads to better generalization than the BP networks.

  19. Kinetic and kinematic analysis of stamping impacts during simulated rucking in rugby union.

    Science.gov (United States)

    Oudshoorn, Bodil Y; Driscoll, Heather F; Dunn, Marcus; James, David

    2018-04-01

    Laceration injuries account for up to 23% of injuries in rugby union. They are frequently caused by studded footwear as a result of a player stamping onto another player during the ruck. Little is known about the kinetics and kinematics of rugby stamping impacts; current test methods assessing laceration injury risk of stud designs therefore lack informed test parameters. In this study, twelve participants stamped on an anthropomorphic test device in a one-on-one simulated ruck setting. Velocity and inclination angle of the foot prior to impact was determined from high-speed video footage. Total stamping force and individual stud force were measured using pressure sensors. Mean foot inbound velocity was 4.3 m ∙ s -1 (range 2.1-6.3 m ∙ s -1 ). Mean peak total force was 1246 N and mean peak stud force was 214 N. The total mean effective mass during stamping was 6.6 kg (range: 1.6-13.5 kg) and stud effective mass was 1.2 kg (range: 0.5-2.9 kg). These results provide representative test parameters for mechanical test devices designed to assess laceration injury risk of studded footwear for rugby union.

  20. Influence of Plastic Deformation on Martensitic Transformation During Hot Stamping of Complex Structure Auto Parts

    Science.gov (United States)

    Shen, Yuhan; Song, Yanli; Hua, Lin; Lu, Jue

    2017-04-01

    The ultra-high strength steel auto parts manufactured by hot stamping are widely applied for weight reduction and safety improvement. During the hot stamping process, hot forming and quenching are performed in one step wherein plastic deformation and phase transformation simultaneously take place and affect each other. Thereinto, the influence of deformation on martensitic transformation is of great importance. In the present paper, the influence of plastic deformation on martensitic transformation during hot stamping of complex structure auto parts was investigated. For this purpose, a B-pillar reinforced panel in B1500HS steel was manufactured by hot stamping, and the process was simulated by finite element software based on a thermo-mechanical-metallurgical coupled model. Considering various deformation degrees, the microstructures and mechanical properties at four typical locations of the hot stamped B-pillar reinforced panel were detected. The results show that the martensitic content and the microhardness increase with the increase in the deformation amount. There are two reasons causing this phenomenon: (1) the increase in mechanical driving force and (2) the increased probability of the martensitic nucleation at crystal defects. The x-ray diffraction analysis indicates the carbon enrichment in retained austenite which results from the carbon diffusion during the low-carbon martensite formation. Furthermore, the carbon content decreases with the increase in the deformation amount, because the deformation of austenite suppresses the carbon diffusion.

  1. Parent Perceptions of Time Spent Meaningfully by Young Adults with Pervasive Support Needs

    Science.gov (United States)

    Rossetti, Zachary; Lehr, Donna; Lederer, Leslie; Pelerin, Dana; Huang, Shuoxi

    2015-01-01

    This article describes a qualitative study that examined how 23 young adults with pervasive support needs and limited functional communication spent their time and how their parents (n = 23) and direct support professionals (DSPs; n = 2) defined meaningfulness in relation to the young adults' experiences. Data were collected through…

  2. Supporting Fourth Graders' Ability to Interpret Graphs through Real-Time Graphing Technology: A Preliminary Study

    Science.gov (United States)

    Deniz, Hasan; Dulger, Mehmet F.

    2012-01-01

    This study examined to what extent inquiry-based instruction supported with real-time graphing technology improves fourth grader's ability to interpret graphs as representations of physical science concepts such as motion and temperature. This study also examined whether there is any difference between inquiry-based instruction supported with…

  3. Identification of a process window for tailored carburization of sheet metals in hot stamping

    Science.gov (United States)

    Horn, Alexander; Merklein, Marion

    2018-05-01

    Due to governmental regulations concerning the reduction of CO2 emissions and increasing safety standards, hot stamping of high strength boron manganese steel sheets has evolved into a state of the art process for manufacturing structural car body parts. The combined forming and in-die quenching process enables the formation of a fully martensitic microstructure. Therefore, press hardened steels offer high strength, but low ductility. In order to further improve passenger safety, a tailored configuration of mechanical properties is desired. Besides state of the art methods, like the application of locally different heat treatment temperatures or varying quenching rates, the adjustment of mechanical properties of sheet metals by a tailored carburization is a novel approach. For the carburization process, the specimens are first coated with graphite and subsequently heat treated. Within this contribution, different coating strategies as well as heat treatment temperatures and dwell times are investigated. For the determination of a process window, mechanical properties such as tensile strength and microhardness will be analyzed and correlated with the resulting microstructure.

  4. A Fully Integrated Humidity Sensor System-on-Chip Fabricated by Micro-Stamping Technology

    Directory of Open Access Journals (Sweden)

    Chih-Ting Lin

    2012-08-01

    Full Text Available A fully integrated humidity sensor chip was designed, implemented, and tested. Utilizing the micro-stamping technology, the pseudo-3D sensor system-on-chip (SSoC architecture can be implemented by stacking sensing materials directly on the top of a CMOS-fabricated chip. The fabricated sensor system-on-chip (2.28 mm × 2.48 mm integrated a humidity sensor, an interface circuit, a digital controller, and an On-Off Keying (OOK wireless transceiver. With low power consumption, i.e., 750 μW without RF operation, the sensitivity of developed sensor chip was experimentally verified in the relative humidity (RH range from 32% to 60%. The response time of the chip was also experimentally verified to be within 5 seconds from RH 36% to RH 64%. As a consequence, the implemented humidity SSoC paves the way toward the an ultra-small sensor system for various applications.

  5. Mechanical behavior and modelisation of Ti-6Al-4V titanium sheet under hot stamping conditions

    Science.gov (United States)

    Sirvin, Q.; Velay, V.; Bonnaire, R.; Penazzi, L.

    2017-10-01

    The Ti-6Al-4V titanium alloy is widely used for the manufacture of aeronautical and automotive parts (solid parts). In aeronautics, this alloy is employed for its excellent mechanical behavior associated with low density, outstanding corrosion resistance and good mechanical properties up to 600°C. It is especially used for the manufacture of fuselage frames, on the pylon for carrying out the primary structure (machining forged blocks) and the secondary structure in sheet form. In this last case, the sheet metal forming can be done through various methods: at room temperature by drawing operation, at very high temperature (≃900°C) by superplastic forming (SPF) and at intermediate temperature (≥750°C) by hot forming (HF). In order to reduce production costs and environmental troubles, the cycle times reduction associated with a decrease of temperature levels are relevant. This study focuses on the behavior modelling of Ti-6Al-4V alloy at temperatures above room temperature to obtained greater formability and below SPF condition to reduce tools workshop and energy costs. The displacement field measurement obtained by Digital Image Correlation (DIC) is based on innovative surface preparation pattern adapted to high temperature exposures. Different material parameters are identified to define a model able to predict the mechanical behavior of Ti-6Al-4V alloy under hot stamping conditions. The hardening plastic model identified is introduced in FEM to simulate an omega shape forming operation.

  6. Just-in-time, Schematic Supportive Information Presentation During Cognitive Skill Acquisition.

    NARCIS (Netherlands)

    Kester, Liesbeth; Lehnen, Chris; Van Gerven, Pascal; Kirschner, Paul A.

    2008-01-01

    Kester, L., Lehnen, C., Van Gerven, P.W. M., & Kirschner, P. A. (2006). Just-in-time, Schematic Supportive Information Presentation During Cognitive Skill Acquisition. Computers in Human Behavior, 22, 93-112 .

  7. Expert system of real time for support of operators of atomic power plants

    International Nuclear Information System (INIS)

    Bashlykov, A.A.; Davidenko, N.N.; Dumshev, V.G.; Kislov, G.I.; Pavlova, E.V.; Prozorovskij, E.D.; Bashlykov, A.A.

    1994-01-01

    The problems of construction and introdution of an intellectual system for information support of operators at nuclear power plants are discussed. This system is used for operator assisstance during real time decision making for NPP operational regime control

  8. 20 CFR 411.180 - What is timely progress toward self-supporting employment?

    Science.gov (United States)

    2010-04-01

    ... Who Are Using a Ticket Introduction § 411.180 What is timely progress toward self-supporting... the previous 12-month progress certification period. In computing any 12-month progress certification...

  9. Semantic-Based Concurrency Control for Object-Oriented Database Systems Supporting Real-Time Applications

    National Research Council Canada - National Science Library

    Lee, Juhnyoung; Son, Sang H

    1994-01-01

    .... This paper investigates major issues in designing semantic-based concurrency control for object-oriented database systems supporting real-time applications, and it describes approaches to solving...

  10. Limited indications of tax stamp discordance and counterfeiting on cigarette packs purchased in tobacco retailers, 97 counties, USA, 2012

    Directory of Open Access Journals (Sweden)

    Joseph G.L. Lee

    2017-12-01

    Full Text Available Increasing the per-unit cost of tobacco products is one of the strongest interventions for tobacco control. In jurisdictions with higher taxes in the U.S., however, cigarette pack litter studies show a substantial proportion of littered packs lack the appropriate tax stamp. More limited but still present counterfeiting also exists. We sought to examine the role of tobacco retailers as a source for untaxed and counterfeit products. Data collectors purchased Newport Green (menthol or Marlboro Red cigarette packs in a national probability-based sample of tobacco retailers (in 97 counties from June–October 2012. They made no effort to buy counterfeit or untaxed cigarettes. In this cross-sectional study, we assessed the presence, tax authority, and type (low-tech thermal vs. encrypted of cigarette pack tax stamps; concordance of tax stamps with where the pack was purchased; and, for Marlboro cigarettes, publicly available visible indicators of counterfeiting. We purchased 2147 packs of which 2033 had tax stamps. Packs missing stamps were in states that do not require them. We found very limited discordance between store location and tax stamp(s (<1%. However, a substantial minority of cigarette packs had damaged tax stamps (13%. This occurred entirely with low-tech tax stamps and was not identified with encrypted tax stamps. We found no clear evidence of counterfeit products. Almost all tax stamps matched the location of purchase. Litter studies may be picking up legal tax avoidance instead of illegal tax evasion or, alternatively, purchase of illicit products requires special request by the purchaser. Keywords: Taxes, Smoking, Tobacco products, Government regulation, Government

  11. Imprints of the Neolithic mind – clay stamps from the Republic of Macedonia

    Directory of Open Access Journals (Sweden)

    Goce Naumov

    2008-12-01

    Full Text Available The presence and unusual structure of clay stamps found in Neolithic settlements often give rise to multiple interpretations to define their character. The small dimensions and specific shape of the stamps suggests that these portable objects were important in the social relations and visual communication between members within the same community and, possibly, more distant communities. The definite patterns distinguishe their function in maintaining the visual traditions of the populations inhabiting southeastern Europe. They had an important role in building the Neolithic image modularity, so that they fitted into the comprehensive decorative structure of Neolithic iconography, and the patterns present on the stamps are related to several aspects of Neolithic material culture from the Balkans and Anatolia. This homogeneity of patterns indicates that they were actively included in the transposition of cognition into visual metaphors.

  12. A framework for development of an intelligent system for design and manufacturing of stamping dies

    Science.gov (United States)

    Hussein, H. M. A.; Kumar, S.

    2014-07-01

    An integration of computer aided design (CAD), computer aided process planning (CAPP) and computer aided manufacturing (CAM) is required for development of an intelligent system to design and manufacture stamping dies in sheet metal industries. In this paper, a framework for development of an intelligent system for design and manufacturing of stamping dies is proposed. In the proposed framework, the intelligent system is structured in form of various expert system modules for different activities of design and manufacturing of dies. All system modules are integrated with each other. The proposed system takes its input in form of a CAD file of sheet metal part, and then system modules automate all tasks related to design and manufacturing of stamping dies. Modules are coded using Visual Basic (VB) and developed on the platform of AutoCAD software.

  13. A framework for development of an intelligent system for design and manufacturing of stamping dies

    International Nuclear Information System (INIS)

    Hussein, H M A; Kumar, S

    2014-01-01

    An integration of computer aided design (CAD), computer aided process planning (CAPP) and computer aided manufacturing (CAM) is required for development of an intelligent system to design and manufacture stamping dies in sheet metal industries. In this paper, a framework for development of an intelligent system for design and manufacturing of stamping dies is proposed. In the proposed framework, the intelligent system is structured in form of various expert system modules for different activities of design and manufacturing of dies. All system modules are integrated with each other. The proposed system takes its input in form of a CAD file of sheet metal part, and then system modules automate all tasks related to design and manufacturing of stamping dies. Modules are coded using Visual Basic (VB) and developed on the platform of AutoCAD software

  14. Micromechanical exfoliation of two-dimensional materials by a polymeric stamp

    International Nuclear Information System (INIS)

    Costa, M C Ferraz da; Ribeiro, H B; Kessler, F; Souza, E A T de; Fechine, G J M

    2016-01-01

    In this work, an alternative technique to the traditional micromechanical exfoliation of two-dimensional materials is proposed, consisting of isolated flakes of graphite and molybdenum disulphide onto polymeric surfaces films. The set made up of polymer and flakes is fabricated by using a hot-press machine called polymeric stamp. The polymeric stamp was used to allocate flakes and also to allow the exfoliation process to take place just in one face of isolated flake. Optical microscopy, Raman spectroscopy and photoluminescence spectroscopy results showed that multilayers, bilayers and single layers of graphene and MoS 2 were obtained by using a polymeric stamp as tool for micromechanical exfoliation. These crystals were more easily found because the exfoliation process concentrates them in well-defined locations. The results prove the effectiveness of the method by embedding two-dimensional materials into polymers to fabricate fewer layers crystals in a fast, economic and clean way. (paper)

  15. Micromechanical exfoliation of two-dimensional materials by a polymeric stamp

    Science.gov (United States)

    Ferraz da Costa, M. C.; Ribeiro, H. B.; Kessler, F.; de Souza, E. A. T.; Fechine, G. J. M.

    2016-02-01

    In this work, an alternative technique to the traditional micromechanical exfoliation of two-dimensional materials is proposed, consisting of isolated flakes of graphite and molybdenum disulphide onto polymeric surfaces films. The set made up of polymer and flakes is fabricated by using a hot-press machine called polymeric stamp. The polymeric stamp was used to allocate flakes and also to allow the exfoliation process to take place just in one face of isolated flake. Optical microscopy, Raman spectroscopy and photoluminescence spectroscopy results showed that multilayers, bilayers and single layers of graphene and MoS2 were obtained by using a polymeric stamp as tool for micromechanical exfoliation. These crystals were more easily found because the exfoliation process concentrates them in well-defined locations. The results prove the effectiveness of the method by embedding two-dimensional materials into polymers to fabricate fewer layers crystals in a fast, economic and clean way.

  16. Numerical simulation of temperature field, microstructure evolution and mechanical properties of HSS during hot stamping

    International Nuclear Information System (INIS)

    Shi, Dongyong; Liu, Wenquan; Ying, Liang; Hu, Ping; Shen, Guozhe

    2013-01-01

    The hot stamping of boron steels is widely used to produce ultra high strength automobile components without any spring back. The ultra high strength of final products is attributed to the fully martensitic microstructure that is obtained through the simultaneous forming and quenching of the hot blanks after austenization. In the present study, a mathematical model incorporating both heat transfer and the transformation of austenite is presented. A FORTRAN program based on finite element technique has been developed which permits the temperature distribution and microstructure evolution of high strength steel during hot stamping process. Two empirical diffusion-dependent transformation models under isothermal conditions were employed respectively, and the prediction capability on mechanical properties of the models were compared with the hot stamping experiment of an automobile B-pillar part

  17. Multi-cycle rolled aluminum alloy 3103 sandwiches: mechanical properties and stamp ability

    Directory of Open Access Journals (Sweden)

    Nosova Ekaterina

    2017-01-01

    Full Text Available Constructional part producing by sheet stamping of multilayer composites requires the stamping ability data. The aim of a work is to estimate mechanical properties, stamping ratio and anisotropy indexes of 2, 4, 8 and 12 layer sandwiches produced from aluminium alloy AA3103. The pieces were received by the cold rolling. Interoperation annealing was at 500°C for 1 hour. Charts of tensile strength, yield stress, elongation depending on layer thickness were composed. It was found that cold strain hardening does not disappear after annealing if the foil’s thickness become 0.4 mm and less. Microstructure analysis has shown a good contact between layers for all samples and thicker outer layers.

  18. Real-time decision support and information gathering system for financial domain

    Science.gov (United States)

    Tseng, Chiu-Che; Gmytrasiewicz, Piotr J.

    2006-05-01

    The challenge of the investment domain is that a large amount of diverse information can be potentially relevant to an investment decision, and that, frequently, the decisions have to be made in a timely manner. This presents the potential for better decision support, but poses the challenge of building a decision support agent that gathers information from different sources and incorporates it for timely decision support. These problems motivate us to investigate ways in which the investors can be equipped with a flexible real-time decision support system to be practical in time-critical situations. The flexible real-time decision support system considers a tradeoff between decision quality and computation cost. For this purpose, we propose a system that uses the object oriented Bayesian knowledge base (OOBKB) design to create a decision model at the most suitable level of detail to guide the information gathering activities, and to produce an investment recommendation within a reasonable length of time. The decision models our system uses are implemented as influence diagrams. We validate our system with experiments in a simplified investment domain. The experiments show that our system produces a quality recommendation under different urgency situations. The contribution of our system is that it provides the flexible decision recommendation for an investor under time constraints in a complex environment.

  19. Background experiences, time allocation, time on teaching and perceived support of early-career college science faculty

    Science.gov (United States)

    Sagendorf, Kenneth S.

    The purposes of this research were to create an inventory of the research, teaching and service background experiences of and to document the time allocation and time spent on teaching by early-career college science faculty members. This project is presented as three distinct papers. Thirty early-career faculty in the science disciplines from sixteen different institutions in their first year of employment participated in this study. For the first two papers, a new survey was developed asking participants to choose which experiences they had acquired prior to taking their current faculty position and asking them to document their time allocation and time spent on teaching activities in an average work week. In addition, a third component documents the support early-career college faculty in the sciences are receiving from the perspective of faculty members and their respective department chairpersons and identifies areas of disagreement between these two different groups. Twenty early-career college science faculty and their respective department chairpersons completed a newly-designed survey regarding the support offered to new faculty. The survey addressed the areas of feedback on performance, clarity of tenure requirements, mentoring, support for teaching and scholarship and balancing faculty life. This dissertation presents the results from these surveys, accounting for different demographic variables such as science discipline, gender and institutional category.

  20. Transfer printing of 3D hierarchical gold structures using a sequentially imprinted polymer stamp

    International Nuclear Information System (INIS)

    Zhang Fengxiang; Low, Hong Yee

    2008-01-01

    Complex three-dimensional (3D) hierarchical structures on polymeric materials are fabricated through a process referred to as sequential imprinting. In this work, the sequentially imprinted polystyrene film is used as a soft stamp to replicate hierarchical structures onto gold (Au) films, and the Au structures are then transferred to a substrate by transfer printing at an elevated temperature and pressure. Continuous and isolated 3D structures can be selectively fabricated with the assistance of thermo-mechanical deformation of the polymer stamp. Hierarchical Au structures are achieved without the need for a corresponding three-dimensionally patterned mold

  1. Determination of Unit Pressure Force in Material Volume in the Course of Refractory Stamping Press Moulding

    Directory of Open Access Journals (Sweden)

    Orłowicz A.W.

    2016-06-01

    Full Text Available The paper presents results of assessment of the unit pressure force within the refractory material volume in the course press-moulding of stampings for refractory precast shapes. The force was evaluated with the use of physical simulation of deformation undergone by lead balls placed in the raw refractory mass subjected to pressing in a metal die. To determine the value of unit pressure force applied to the aggregate grains in the course of stamping press-moulding, physical model of deformation of a sphere induced by the uniaxial stress state was used.

  2. Development and introduction of stamping technique for large-size laterals of NPP pipelines

    International Nuclear Information System (INIS)

    Romashko, N.I.; Moshnin, E.N.; Timokhin, V.S.; Bryukhanov, Yu.V.; Lebedev, V.A.

    1984-01-01

    The results of development and introduction of stamping technique for large-size laterals of NPP high-pressure pipelines are presented. The main experimental data characterizing technological possibilities of the process are given. The technological process and design of the stamp assure production of laterals from ovalized bars per one heating of the bar and per one running of the press cronnhead. Introduction of new technology decreased labour input of lateral production, reliability and serviceability of pipelines increased in this case. Introduction of this technology gives a considerable benefit

  3. Supporting the Academic Majority: Policies and Practices Related to Part-Time Faculty's Job Satisfaction

    Science.gov (United States)

    Eagan, M. Kevin, Jr.; Jaeger, Audrey J.; Grantham, Ashley

    2015-01-01

    The academic workforce in higher education has shifted in the last several decades from consisting of mostly full-time, tenure-track faculty to one comprised predominantly of contingent, non-tenure-track faculty. This substantial shift toward part-time academic labor has not corresponded with institutions implementing more supportive policies and…

  4. Analysis of Two-Level Support Systems with Time-Dependent Overflow - A Banking Application

    DEFF Research Database (Denmark)

    Barth, Wolfgang; Manitz, Michael; Stolletz, Raik

    2010-01-01

    In this paper, we analyze the performance of call centers of financial service providers with two levels of support and a time-dependent overflow mechanism. Waiting calls from the front-office queue flow over to the back office if a waiting-time limit is reached and at least one back-office agent...

  5. Supporting Development of Energy-Optimised Java Real-Time Systems using TetaSARTS

    DEFF Research Database (Denmark)

    Luckow, Kasper Søe; Bøgholm, Thomas; Thomsen, Bent

    2013-01-01

    This paper presents how the tool TetaSARTS can be used to support the development of embedded hard real-time systems written in Java using the emerging Safety Critical Java (SCJ) profile. TetaSARTS facilitates control-flow sensitive schedulability analysis of a set of real-time tasks, and features...

  6. A Lecture Supporting System Based on Real-Time Learning Analytics

    Science.gov (United States)

    Shimada, Atsushi; Konomi, Shin'ichi

    2017-01-01

    A new lecture supporting system based on real-time learning analytics is proposed. Our target is on-site classrooms where teachers give their lectures, and a lot of students listen to teachers' explanation, conduct exercises etc. We utilize not only an e-Learning system, but also an e-Book system to collect real-time learning activities during the…

  7. 45 CFR 205.25 - Eligibility of supplemental security income beneficiaries for food stamps or surplus commodities.

    Science.gov (United States)

    2010-10-01

    ... beneficiaries for food stamps or surplus commodities. 205.25 Section 205.25 Public Welfare Regulations Relating....25 Eligibility of supplemental security income beneficiaries for food stamps or surplus commodities... XVI of the Social Security Act, the State agency shall make the following determinations: (1) The...

  8. The influence of social support and perceived stress on response time inconsistency.

    Science.gov (United States)

    Phibbs, Sandi; Stawski, Robert S; MacDonald, Stuart W S; Munoz, Elizabeth; Smyth, Joshua M; Sliwinski, Martin J

    2017-11-24

    Lack of social support and high levels of stress represent potentially modifiable risk factors for cognitive aging. In this study we examined the relationships between these two risk factors and response time inconsistency (RTI), or trial-to-trial variability in choice response time tasks. RTI is an early indicator of declining cognitive health, and examining the influence of modifiable psychosocial risk factors on RTI is important for understanding and promoting cognitive health during adulthood and old age. Using data from a community sample study (n = 317; M age = 49, range = 19-83), we examined the effects of social support, including size of network and satisfaction with support, global perceived stress, and their interactions on RTI. Neither size of network nor satisfaction with support was associated with RTI independent of perceived stress. Stress was positively associated with increased RTI on all tasks, independent of social support. Perceived stress did not interact with either dimension of social support to predict RTI, and perceived stress effects were invariant across age and sex. Perceived stress, but not social support, may be a unique and modifiable risk factor for normal and pathological cognitive aging. Discussion focuses on the importance of perceived stress and its impact on RTI in supporting cognitive health in adulthood and old age.

  9. The importance of good time management in supporting succesful dental practice

    OpenAIRE

    Mita Juliawati

    2016-01-01

    n the globalization and Asean Economic Community (MEA) era, especially in the era of  competition and modern dentistry, dentists need increasing services in order to maintain and increase patient visits. Especially in patient’s complain about dental services that caused by unmanaged time, such as late dentist, long queue of patients and time inefficiency in dental practice. The objective of this review is to discuss the importance of good time management ’in supporting successful dental prati...

  10. Mothering and anxiety: Social support and competence as mitigating factors for first-time mothers.

    Science.gov (United States)

    Chavis, Llena

    2016-07-01

    This study investigated anxiety as a phenomenon distinct from depression and evaluated several variables that influence anxiety in first-time mothers. This explored the relationship between maternal sense of competence (both of mothering and efficacy) and perceived social support (from family, friends, and significant others) and first-time mothers' postpartum anxiety, when depression, socioeconomic status (SES), and marital status were controlled for. The population studied were 86 first-time mothers made up of women with children 24 months or younger in two populations of Kentucky and Michigan. The constructs of maternal sense of competence and perceived social support were found to be significant in explaining first-time mothers' anxiety. The study concluded that a combined association of perceived social support and maternal sense of competence were associated with a 34% (change in R-squared = .339) decrease of a first-time mothers' anxiety. However, not all types of social support, or maternal competence appeared to be equally important with regards to maternal anxiety: social support from friends and family and maternal sense of competence in regard to productivity appeared to be most significant. Lastly, some recommendations for health practitioners who work with mothers are provided.

  11. Job quality of short-time workers and perception and support from their managers

    OpenAIRE

    坂爪, 洋美

    2017-01-01

    The purpose of this study was to clarify the relationship between the characteristics of job quality that short-time workers occupied and the managers’ perception and support whose member has used short-time working hour system. A total of 559 first-line managers who has a member using short-time working hour system completed a web-based survey assessing job quality of short-time workers , the risk of using short-timeworking hour system, career perspective of short-time workers, and the suppo...

  12. Leisure-Time Physical Activity and Characteristics of Social Network Support for Exercise Among Latinas.

    Science.gov (United States)

    Soto, Sandra H; Arredondo, Elva M; Haughton, Jessica; Shakya, Holly

    2018-02-01

    To examine the association between characteristics of social support for exercise and moderate-to-vigorous leisure-time physical activity (LTPA) among Latinas. This cross-sectional study used baseline data from a cluster randomized controlled trial. The study was conducted in 16 churches located in San Diego County. Participants (N = 436) were Latinas between 18 and 65 years old who did not self-report >150 minutes or did not exceed 250 minutes of moderate-to-vigorous PA per week measured by accelerometer. Latinas listed up to 6 individuals who had provided support for exercise within the past 6 months, including their gender, relationship with the respondent, types of support provided, and respondent's satisfaction with support. Self-reported LTPA was dichotomized (none vs any). We generated dyads between Latinas who named ≥1 supporter (n = 323) and each supporter they named (n = 569 dyads). Logistic regression analyses were conducted using generalized estimating equations to adjust for multiple observations per participant. Having an exercise partner (odds ratio [OR]: 2.16; 95% confidence interval [CI]: 1.01-4.62), help with household duties (OR: 2.70; 95% CI: 1.35-3.38), being "very much" satisfied with support (OR: 2.33; 95% CI: 1.26-4.30), and naming >2 supporters (OR: 2.57; 95% CI: 1.06-6.25) was positively associated with LTPA. Findings suggest specific aspects of support for exercise that should be targeted in future interventions to promote LTPA.

  13. Discussion About Nonlinear Time Series Prediction Using Least Squares Support Vector Machine

    International Nuclear Information System (INIS)

    Xu Ruirui; Bian Guoxing; Gao Chenfeng; Chen Tianlun

    2005-01-01

    The least squares support vector machine (LS-SVM) is used to study the nonlinear time series prediction. First, the parameter γ and multi-step prediction capabilities of the LS-SVM network are discussed. Then we employ clustering method in the model to prune the number of the support values. The learning rate and the capabilities of filtering noise for LS-SVM are all greatly improved.

  14. Comparison study of time history and response spectrum responses for multiply supported piping systems

    International Nuclear Information System (INIS)

    Wang, Y.K.; Subudhi, M.; Bezler, P.

    1983-01-01

    In the past decade, several investigators have studied the problem of independent support excitation of a multiply supported piping system to identify the real need for such an analysis. This approach offers an increase in accuracy at a small increase in computational costs. To assess the method, studies based on the response spectrum approach using independent support motions for each group of commonly connected supports were performed. The results obtained from this approach were compared with the conventional envelope spectrum and time history solutions. The present study includes a mathematical formulation of the independent support motion analysis method suitable for implementation into an existing all purpose piping code PSAFE2 and a comparison of the solutions for some typical piping system using both Time History and Response Spectrum Methods. The results obtained from the Response Spectrum Methods represent the upper bound solution at most points in the piping system. Similarly, the Seismic Anchor Movement analysis based on the SRP method over predicts the responses near the support points and under predicts at points away from the supports

  15. Delivering "Just-In-Time" Smoking Cessation Support Via Mobile Phones: Current Knowledge and Future Directions.

    Science.gov (United States)

    Naughton, Felix

    2016-05-28

    Smoking lapses early on during a quit attempt are highly predictive of failing to quit. A large proportion of these lapses are driven by cravings brought about by situational and environmental cues. Use of cognitive-behavioral lapse prevention strategies to combat cue-induced cravings is associated with a reduced risk of lapse, but evidence is lacking in how these strategies can be effectively promoted. Unlike most traditional methods of delivering behavioral support, mobile phones can in principle deliver automated support, including lapse prevention strategy recommendations, Just-In-Time (JIT) for when a smoker is most vulnerable, and prevent early lapse. JIT support can be activated by smokers themselves (user-triggered), by prespecified rules (server-triggered) or through sensors that dynamically monitor a smoker's context and trigger support when a high risk environment is sensed (context-triggered), also known as a Just-In-Time Adaptive Intervention (JITAI). However, research suggests that user-triggered JIT cessation support is seldom used and existing server-triggered JIT support is likely to lack sufficient accuracy to effectively target high-risk situations in real time. Evaluations of mobile phone cessation interventions that include user and/or server-triggered JIT support have yet to adequately assess whether this improves management of high risk situations. While context-triggered systems have the greatest potential to deliver JIT support, there are, as yet, no impact evaluations of such systems. Although it may soon be feasible to learn about and monitor a smoker's context unobtrusively using their smartphone without burdensome data entry, there are several potential advantages to involving the smoker in data collection. This commentary describes the current knowledge on the potential for mobile phones to deliver automated support to help smokers manage or cope with high risk environments or situations for smoking, known as JIT support. The article

  16. Stamp design effect on 100 nm feature size for 8 inch NanoImprint lithography

    International Nuclear Information System (INIS)

    Landis, S; Chaix, N; Gourgon, C; Perret, C; Leveder, T

    2006-01-01

    Sub-100 nm resolution on a 200 mm silicon stamp has been hot embossed into commercial Sumitomo NEB 22 resist. A single pattern, exposed with electron beam lithography, has been considered to define the stamp and thus make it possible to point out the impact of stamp design on the printing. These results may be considered as a first attempt to define rules to solve the proximity printing effects (PPEs). Moreover, a large range of initial resist thickness, from 56 to 506 nm, has been spin coated to assess the effect of polymer flow properties for the stamp cavity filling and the printed defects. A detailed analysis of the printed resist in dense hole patterns showed that the application volume conservation is enough to calculate the residual layer thickness as the height of the printed resist feature. Good accordance has been obtained between the theoretical approach and experimental results. Moreover, the impact of the pattern symmetry breakdown on mould deformation is clearly shown in this paper in the printed areas as well as in the unprinted areas

  17. Studying the Solar System Can Be More than Just "Stamp Collecting"

    Science.gov (United States)

    LoPresto, Michael C.

    2017-01-01

    While teaching his first-ever introductory college astronomy course, I heard a graduate student make the comment that compared to other areas of astronomy, studying the solar system is just "stamp collecting." Coverage of the solar system in an introductory college astronomy course certainly "could" consist mostly of showing…

  18. A rapid co-culture stamping device for studying intercellular communication

    Science.gov (United States)

    Hassanzadeh-Barforoushi, Amin; Shemesh, Jonathan; Farbehi, Nona; Asadnia, Mohsen; Yeoh, Guan Heng; Harvey, Richard P.; Nordon, Robert E.; Warkiani, Majid Ebrahimi

    2016-10-01

    Regulation of tissue development and repair depends on communication between neighbouring cells. Recent advances in cell micro-contact printing and microfluidics have facilitated the in-vitro study of homotypic and heterotypic cell-cell interaction. Nonetheless, these techniques are still complicated to perform and as a result, are seldom used by biologists. We report here development of a temporarily sealed microfluidic stamping device which utilizes a novel valve design for patterning two adherent cell lines with well-defined interlacing configurations to study cell-cell interactions. We demonstrate post-stamping cell viability of >95%, the stamping of multiple adherent cell types, and the ability to control the seeded cell density. We also show viability, proliferation and migration of cultured cells, enabling analysis of co-culture boundary conditions on cell fate. We also developed an in-vitro model of endothelial and cardiac stem cell interactions, which are thought to regulate coronary repair after myocardial injury. The stamp is fabricated using microfabrication techniques, is operated with a lab pipettor and uses very low reagent volumes of 20 μl with cell injection efficiency of >70%. This easy-to-use device provides a general strategy for micro-patterning of multiple cell types and will be important for studying cell-cell interactions in a multitude of applications.

  19. Ramón y Cajal erroneously identified as Camillo Golgi on a souvenir postage stamp.

    Science.gov (United States)

    Triarhou, Lazaros C; del Cerro, Manuel

    2012-01-01

    Focusing on a philatelic oddity that erringly identifies a picture of Santiago Ramón y Cajal as that of Camillo Golgi, this brief article examines official and unofficial stamp issues honoring the two great neuroanatomists, one from Spain and the other from Italy, who were early Nobel Prize winners in Physiology or Medicine.

  20. Human factors science and safety engineering : can the STAMP model serve in establishing a common language?

    NARCIS (Netherlands)

    Karanikas, Nektarios; Schwarz, M; Harfmann, J

    2017-01-01

    A symbiotic relationship between human factors and safety scientists is needed to ensure the provision of holistic solutions for problems emerging in modern socio-technical systems. System Theoretic Accident Model and Processes (STAMP) tackles both interactions and individual failures of human and

  1. Silicon oxide nanoimprint stamp fabrication by edge lithography reinforced with silicon nitride

    NARCIS (Netherlands)

    Zhao, Yiping; Berenschot, Johan W.; de Boer, Meint J.; Jansen, Henricus V.; Tas, Niels Roelof; Huskens, Jurriaan; Elwenspoek, Michael Curt

    2007-01-01

    The fabrication of silicon oxide nanoimprint stamp employing edge lithography in combination with silicon nitride deposition is presented. The fabrication process is based on conventional photolithography an weg etching methods. Nanoridges with width dimension of sub-20 nm were fabricated by edge

  2. Fabrication of a silicon oxide stamp by edge lithography reinforced with silicon nitride for nanoimprint lithography

    NARCIS (Netherlands)

    Zhao, Yiping; Berenschot, Johan W.; de Boer, M.; de Boer, Meint J.; Jansen, Henricus V.; Tas, Niels Roelof; Huskens, Jurriaan; Elwenspoek, Michael Curt

    2008-01-01

    The fabrication of a stamp reinforced with silicon nitride is presented for its use in nanoimprint lithography. The fabrication process is based on edge lithography using conventional optical lithography and wet anisotropic etching of 110 silicon wafers. SiO2 nano-ridges of 20 nm in width were

  3. Determination of Proper Austenitization Temperatures for Hot Stamping of AISI 4140 Steel

    Science.gov (United States)

    Samadian, Pedram; Parsa, Mohammad Habibi; Shakeri, Amid

    2014-04-01

    High strength steels are desirable materials for use in automobile bodies in order to reduce vehicle weight and increase the safety of car passengers, but steel grades with high strength commonly show poor formability. Recently, steels with controlled microstructures and compositions are used to gain adequate strength after hot stamping while maintaining good formability during processing. In this study, microstructure evolutions and changes in mechanical properties of AISI 4140 steel sheets resulting from the hot stamping process at different austenitization temperatures were investigated. To determine the proper austenitization temperatures, the results were compared with those of the cold-worked and cold-worked plus quench-tempered specimens. Comparisons showed that the austenitization temperatures of 1000 and 1100 °C are proper for hot stamping of 3-mm-thick AISI 4140 steel sheets due to the resultant martensitic microstructure which led to the yield and ultimate tensile strength of 1.3 and 2.1 GPa, respectively. Such conditions resulted in more favorable simultaneous strength and elongation than those of hot-stamped conventional boron steels.

  4. Development of Core Competencies for Paraprofessional Nutrition Educators Who Deliver Food Stamp Nutrition Education

    Science.gov (United States)

    Baker, Susan S.; Pearson, Meredith; Chipman, Helen

    2009-01-01

    The purpose of this project was to describe the process used for the development of core competencies for paraprofessional nutrition educators in Food Stamp Nutrition Education (FSNE). The development process included the efforts of an expert panel of state and multicounty FSNE leaders to draft the core competencies and the validation of those…

  5. Corrosion resistance characteristics of stamped and hydroformed proton exchange membrane fuel cell metallic bipolar plates

    Energy Technology Data Exchange (ETDEWEB)

    Dundar, F. [NSF I/UCRC Center for Precision Forming (CPF), Virginia Commonwealth University, Richmond, VA (United States); Department of Materials Science and Engineering, Gebze Institute of Technology (Turkey); Dur, Ender; Koc, M. [NSF I/UCRC Center for Precision Forming (CPF), Virginia Commonwealth University, Richmond, VA (United States); Mahabunphachai, S. [NSF I/UCRC Center for Precision Forming (CPF), Virginia Commonwealth University, Richmond, VA (United States); National Metal and Materials Technology Center (MTEC), Pathumthani (Thailand)

    2010-06-01

    Metallic bipolar plates have several advantages over bipolar plates made from graphite and composites due to their high conductivity, low material and production costs. Moreover, thin bipolar plates are possible with metallic alloys, and hence low fuel cell stack volume and mass are. Among existing fabrication methods for metallic bipolar plates, stamping and hydroforming are seen as prominent approaches for mass production scales. In this study, the effects of important process parameters of these manufacturing processes on the corrosion resistance of metallic bipolar plates made of SS304 were investigated. Specifically, the effects of punch speed, pressure rate, stamping force and hydroforming pressure were studied as they were considered to inevitably affect the bipolar plate micro-channel dimensions, surface topography, and hence the corrosion resistance. Corrosion resistance under real fuel cell conditions was examined using both potentiodynamic and potentiostatic experiments. The majority of the results exhibited a reduction in the corrosion resistance for both stamped and hydroformed plates when compared with non-deformed blank plates of SS304. In addition, it was observed that there exist an optimal process window for punch speed in stamping and the pressure rate in hydroforming to achieve improved corrosion resistance at a faster production rate. (author)

  6. Breastfeeding protection, promotion, and support in the United States: a time to nudge, a time to measure.

    Science.gov (United States)

    Pérez-Escamilla, Rafael; Chapman, Donna J

    2012-05-01

    Strong evidence-based advocacy efforts have now translated into high level political support and concrete goals for improving breastfeeding outcomes among women in the United States. In spite of this, major challenge remain for promoting, supporting and especially for protecting breastfeeding in the country. The goals of this commentary are to argue in favor of: A) Changes in the default social and environmental systems, that would allow women to implement their right to breastfeed their infants, B) A multi-level and comprehensive monitoring system to measure process and outcomes indicators in the country. Evidence-based commentary. Breastfeeding rates in the United States can improve based on a well coordinated social marketing framework. This approach calls for innovative promotion through mass media, appropriate facility based and community based support (e.g., Baby Friendly Hospital Initiative, WIC-coordinated community based peer counseling), and adequate protection for working women (e.g., longer paid maternity leave, breastfeeding or breast milk extraction breaks during the working day) and women at large by adhering and enforcing the WHO ethics Code for the Marketing of Breast Milk Substitutes. Sound infant feeding practices monitoring systems, which include WIC administrative food package data, are needed. Given the current high level of political support to improve breastfeeding in the United States, a window of opportunity has been opened. Establishing breastfeeding as the social norm in the USA will take time, but the global experience indicates that it can be done.

  7. MECHANICAL VIBRATION INHIBITS OSTEOCLAST FORMATION BY REDUCING DC-STAMP RECEPTOR EXPRESSION IN OSTEOCLAST PRECURSOR CELLS

    Science.gov (United States)

    Kulkarni, R.N.; Voglewede, P.A.; Liu, D.

    2014-01-01

    It is well known that physical inactivity leads to loss of muscle mass, but it also causes bone loss. Mechanistically, osteoclastogenesis and bone resorption have recently been shown to be regulated by vibration. However, the underlying mechanism behind the inhibition of osteoclast formation is yet unknown. Therefore, we investigated whether mechanical vibration of osteoclast precursor cells affects osteoclast formation by the involvement of fusion-related molecules such as dendritic cell-specific transmembrane protein (DC-STAMP), and P2X7 receptor (P2X7R). RAW264.7 (a murine osteoclastic-like cell line) cells were treated with 20 ng/ml receptor activator of NF-κB ligand (RANKL). For 3 consecutive days, the cells were subjected to 1 hour of mechanical vibration with 20 µm displacement at a frequency of 4 Hz and compared to the control cells that were treated under the same condition but without the vibration. After 5 days of culture, osteoclast formation was determined. Gene expression of DC-STAMP and P2X7R by RAW264.7 cells were determined after 1 hour mechanical vibration, while protein production of the DC-STAMP was determined after 6 hours of post incubation after vibration. As a result, mechanical vibration of RAW264.7 cells inhibited the formation of osteoclasts. Vibration down-regulated DC-STAMP gene expression by 1.6-fold in the presence of RANKL and by 1.4-fold in the absence of RANKL. Additionally, DC-STAMP protein production was also down-regulated by 1.4-fold in the presence of RANKL and by 1.2-fold in the absence of RANKL in RAW264.7 cells in response to mechanical vibration. However, vibration did not affect P2X7R gene expression. Mouse anti-DC-STAMP antibody inhibited osteoclast formation in the absence of vibration. Our results suggest that mechanical vibration of osteoclast precursor cells reduce DC-STAMP expression in osteoclast precursor cells leading to the inhibition of osteoclast formation. PMID:23994170

  8. Mechanical vibration inhibits osteoclast formation by reducing DC-STAMP receptor expression in osteoclast precursor cells.

    Science.gov (United States)

    Kulkarni, Rishikesh N; Voglewede, Philip A; Liu, Dawei

    2013-12-01

    It is well known that physical inactivity leads to loss of muscle mass, but it also causes bone loss. Mechanistically, osteoclastogenesis and bone resorption have recently been shown to be regulated by vibration. However, the underlying mechanism behind the inhibition of osteoclast formation is yet unknown. Therefore, we investigated whether mechanical vibration of osteoclast precursor cells affects osteoclast formation by the involvement of fusion-related molecules such as dendritic cell-specific transmembrane protein (DC-STAMP) and P2X7 receptor (P2X7R). RAW264.7 (a murine osteoclastic-like cell line) cells were treated with 20ng/ml receptor activator of NF-κB ligand (RANKL). For 3 consecutive days, the cells were subjected to 1h of mechanical vibration with 20μm displacement at a frequency of 4Hz and compared to the control cells that were treated under the same condition but without the vibration. After 5days of culture, osteoclast formation was determined. Gene expression of DC-STAMP and P2X7R by RAW264.7 cells was determined after 1h of mechanical vibration, while protein production of the DC-STAMP was determined after 6h of postincubation after vibration. As a result, mechanical vibration of RAW264.7 cells inhibited the formation of osteoclasts. Vibration down-regulated DC-STAMP gene expression by 1.6-fold in the presence of RANKL and by 1.4-fold in the absence of RANKL. Additionally, DC-STAMP protein production was also down-regulated by 1.4-fold in the presence of RANKL and by 1.2-fold in the absence of RANKL in RAW264.7 cells in response to mechanical vibration. However, vibration did not affect P2X7R gene expression. Mouse anti-DC-STAMP antibody inhibited osteoclast formation in the absence of vibration. Our results suggest that mechanical vibration of osteoclast precursor cells reduces DC-STAMP expression in osteoclast precursor cells leading to the inhibition of osteoclast formation. © 2013 Elsevier Inc. All rights reserved.

  9. Multi-Layer Real-Time Support for JVM-based Smart Phone Systems

    Directory of Open Access Journals (Sweden)

    SEO, E.

    2013-08-01

    Full Text Available Employing the Java virtual machine (JVM architecture provides smart phone systems stability and security by sandboxing third-party applications and controlling their behavior. However, the JVM layer hinders applications from notifying the operating system scheduler about their timeliness requirements; therefore, applications sometimes fail to respond on time. In order to improve the responsiveness of smart phone applications, this paper proposes two schemes. First, for existing applications that cannot be rebuilt, we modify the kernel scheduler to value task priorities over fairness. Second, we propose cross-layer real-time support APIs to deliver applications' priorities to the kernel scheduler, which will help developers to add real-time scheduling support to their applications. Our prototype demonstrates that the suggested schemes dramatically improve response times and throughputs of prioritized applications.

  10. Development and use of interactive displays in real-time ground support research facilities

    Science.gov (United States)

    Rhea, Donald C.; Hammons, Kvin R.; Malone, Jacqueline C.; Nesel, Michael C.

    1989-01-01

    The NASA Western Aeronautical Test Range (WATR) is one of the world's most advanced aeronautical research flight test support facilities. A variety of advanced and often unique real-time interactive displays has been developed for use in the mission control centers (MCC) to support research flight and ground testing. These dispalys consist of applications operating on systems described as real-time interactive graphics super workstations and real-time interactive PC/AT compatible workstations. This paper reviews these two types of workstations and the specific applications operating on each display system. The applications provide examples that demonstrate overall system capability applicable for use in other ground-based real-time research/test facilities.

  11. Faculty workload and collegial support related to proportion of part-time faculty composition.

    Science.gov (United States)

    Adams, D A

    1995-10-01

    Part-time faculty use has become more prevalent in higher education in response to enrollment shifts and budgetary constraints. This descriptive, exploratory study used a mailed survey to investigate whether full-time nursing faculty perceptions of workload and collegial support differ with changes in the proportion of part-time faculty in Comprehensive I baccalaureate nursing programs. Workload was measured by Dick's Workload Instrument. Collegial support was measured by the Survey of Collegial Communication, adapted by Beyer, which was based on Likert's organizational model. Schools were partitioned into three strata based on the proportion of part-time faculty employed (low, medium, and high). A 30% sample of schools were randomly selected from each stratum (10 schools from each). Within each selected school, six full-time undergraduate faculty were chosen by their respective deans to participate. The total response rate was 89.4%. The results of this study did not support assertions about part-time faculty use in the literature and existing accreditation standards. Findings indicated that there were significant differences in reported total faculty workload when varying proportions of part-time faculty are employed. Faculty in nursing programs with medium proportions of part-time faculty reported higher average total workloads per week than faculty in programs with low and high proportions of part-timers. Another finding demonstrated that full-time faculty in nursing programs with high proportions of part-time faculty spend fewer hours in direct clinical supervision of their students when compared with faculty in the other two strata. There were, however, no differences in perceived collegial support among full-time faculty participants. It was recommended that further research be conducted to investigate specific workload differences found in this study using more precise quantitative measures. Communication and collegiality between part-time and full-time

  12. Predicting Child Physical Activity and Screen Time: Parental Support for Physical Activity and General Parenting Styles

    Science.gov (United States)

    Crain, A. Lauren; Senso, Meghan M.; Levy, Rona L.; Sherwood, Nancy E.

    2014-01-01

    Objective: To examine relationships between parenting styles and practices and child moderate-to-vigorous physical activity (MVPA) and screen time. Methods: Participants were children (6.9 ± 1.8 years) with a body mass index in the 70–95th percentile and their parents (421 dyads). Parent-completed questionnaires assessed parental support for child physical activity (PA), parenting styles and child screen time. Children wore accelerometers to assess MVPA. Results: Parenting style did not predict MVPA, but support for PA did (positive association). The association between support and MVPA, moreover, varied as a function of permissive parenting. For parents high in permissiveness, the association was positive (greater support was related to greater MVPA and therefore protective). For parents low in permissiveness, the association was neutral; support did not matter. Authoritarian and permissive parenting styles were both associated with greater screen time. Conclusions: Parenting practices and styles should be considered jointly, offering implications for tailored interventions. PMID:24812256

  13. Predicting child physical activity and screen time: parental support for physical activity and general parenting styles.

    Science.gov (United States)

    Langer, Shelby L; Crain, A Lauren; Senso, Meghan M; Levy, Rona L; Sherwood, Nancy E

    2014-07-01

    To examine relationships between parenting styles and practices and child moderate-to-vigorous physical activity (MVPA) and screen time. Participants were children (6.9 ± 1.8 years) with a body mass index in the 70-95th percentile and their parents (421 dyads). Parent-completed questionnaires assessed parental support for child physical activity (PA), parenting styles and child screen time. Children wore accelerometers to assess MVPA. Parenting style did not predict MVPA, but support for PA did (positive association). The association between support and MVPA, moreover, varied as a function of permissive parenting. For parents high in permissiveness, the association was positive (greater support was related to greater MVPA and therefore protective). For parents low in permissiveness, the association was neutral; support did not matter. Authoritarian and permissive parenting styles were both associated with greater screen time. Parenting practices and styles should be considered jointly, offering implications for tailored interventions. © The Author 2014. Published by Oxford University Press on behalf of the Society of Pediatric Psychology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  14. First-time fathers' postnatal experiences and support needs: A descriptive qualitative study.

    Science.gov (United States)

    Shorey, Shefaly; Dennis, Cindy-Lee; Bridge, Shiho; Chong, Yap Seng; Holroyd, Eleanor; He, Hong-Gu

    2017-12-01

    To explore first-time fathers' postnatal experiences and support needs in the early postpartum period. The postnatal period is a stressful transition period for new fathers. It is imperative to understand their needs and experiences to provide appropriate support for them. The majority of previous studies were based in Western countries and explored fathers' needs during pregnancy and childbirth, with few studies conducted in the postnatal period. In Singapore, a multiracial society with differing paternal cultural values from its Western counterparts, there is considerable need to examine the experiences and needs of first-time fathers. A descriptive qualitative design was used. Data were collected from November 2015-January 2016. Fifteen first-time fathers were recruited from two postnatal wards of a public hospital, using a purposive sampling method. A semi-structured interview guide was used to conduct face-to-face interviews. A thematic analysis was conducted and ethics approval was sought for this study. Four overarching themes and seventeen subthemes were generated. The four overarching themes were: (1) No sense of reality to sense of responsibility; (2) Unprepared and challenged; (3) Support: needs, sources, experience and attitude; and (4) Future help for fathers. Fathers undergo a transition phase where they have unmet support needs during the early postnatal period. Understanding and addressing these needs may facilitate smooth transition to fatherhood. This study's findings can be used to involve fathers and design future supportive educational programs to promote positive parenting experiences and family dynamics. © 2017 John Wiley & Sons Ltd.

  15. The importance of good time management in supporting succesful dental practice

    Directory of Open Access Journals (Sweden)

    Mita Juliawati

    2016-06-01

    Full Text Available n the globalization and Asean Economic Community (MEA era, especially in the era of  competition and modern dentistry, dentists need increasing services in order to maintain and increase patient visits. Especially in patient’s complain about dental services that caused by unmanaged time, such as late dentist, long queue of patients and time inefficiency in dental practice. The objective of this review is to discuss the importance of good time management ’in supporting successful dental pratice. Time management is the act or process of planning and exercising conscious control over the amount of time spent on specific activities, especially to increase  effectiveness, efficiency or productivity. Implementation in dental practice are as follow: planning, scheduling and time organizing to avoid wasted time. Proper time management resulted in greater efficiency and productivity, professional reputation,reduces stress and improves the image of dental practices. Routine evaluation is needed to increase time management quality. Efficient time management in dental practice requires organizing  individual tasks, analizing daily task, scheduling main projects, establishing deadlines and organizing workflow. The implementation in dental practice like organizing patients, medical and non medical employee daily schedule, managing the patient’s queue to get the minimum waiting time and avoiding doctors being late in giving services to patient. Setting good time management will make the dentist's work 'smarter not harder' to get more results with limited time. In principle all medical and non-medical personnel should support the implementation of service excellence in the health care services especially dental practice. The final objective in realizing good time management in dental clinic is concerning in quality service and aims to achieve patient satisfaction (customer satisfaction that the end goal is a loyal patient, customer loyalty and

  16. New technologies for supporting real-time on-board software development

    Science.gov (United States)

    Kerridge, D.

    1995-03-01

    The next generation of on-board data management systems will be significantly more complex than current designs, and will be required to perform more complex and demanding tasks in software. Improved hardware technology, in the form of the MA31750 radiation hard processor, is one key component in addressing the needs of future embedded systems. However, to complement these hardware advances, improved support for the design and implementation of real-time data management software is now needed. This will help to control the cost and risk assoicated with developing data management software development as it becomes an increasingly significant element within embedded systems. One particular problem with developing embedded software is managing the non-functional requirements in a systematic way. This paper identifies how Logica has exploited recent developments in hard real-time theory to address this problem through the use of new hard real-time analysis and design methods which can be supported by specialized tools. The first stage in transferring this technology from the research domain to industrial application has already been completed. The MA37150 Hard Real-Time Embedded Software Support Environment (HESSE) is a loosely integrated set of hardware and software tools which directly support the process of hard real-time analysis for software targeting the MA31750 processor. With further development, this HESSE promises to provide embedded system developers with software tools which can reduce the risks associated with developing complex hard real-time software. Supported in this way by more sophisticated software methods and tools, it is foreseen that MA31750 based embedded systems can meet the processing needs for the next generation of on-board data management systems.

  17. Supporting Multiprocessors in the Icecap Safety-Critical Java Run-Time Environment

    DEFF Research Database (Denmark)

    Zhao, Shuai; Wellings, Andy; Korsholm, Stephan Erbs

    The current version of the Safety Critical Java (SCJ) specification defines three compliance levels. Level 0 targets single processor programs while Level 1 and 2 can support multiprocessor platforms. Level 1 programs must be fully partitioned but Level 2 programs can also be more globally...... scheduled. As of yet, there is no official Reference Implementation for SCJ. However, the icecap project has produced a Safety-Critical Java Run-time Environment based on the Hardware-near Virtual Machine (HVM). This supports SCJ at all compliance levels and provides an implementation of the safety......-critical Java (javax.safetycritical) package. This is still work-in-progress and lacks certain key features. Among these is the ability to support multiprocessor platforms. In this paper, we explore two possible options to adding multiprocessor support to this environment: the “green thread” and the “native...

  18. Evolving from Planning and Scheduling to Real-Time Operations Support: Design Challenges

    Science.gov (United States)

    Marquez, Jessica J.; Ludowise, Melissa; McCurdy, Michael; Li, Jack

    2010-01-01

    Versions of Scheduling and Planning Interface for Exploration (SPIFe) have supported a variety of mission operations across NASA. This software tool has evolved and matured over several years, assisting planners who develop intricate schedules. While initially conceived for surface Mars missions, SPIFe has been deployed in other domains, where people rather than robotic explorers, execute plans. As a result, a diverse set of end-users has compelled growth in a new direction: supporting real-time operations. This paper describes the new needs and challenges that accompany this development. Among the key features that have been built for SPIFe are current time indicators integrated into the interface and timeline, as well as other plan attributes that enable execution of scheduled activities. Field tests include mission support for the Lunar CRater Observation and Sensing Satellite (LCROSS), NASA Extreme Environment Mission Operations (NEEMO) and Desert Research and Technology Studies (DRATS) campaigns.

  19. Real-time support for precision excavation of radionuclide-contaminated soils

    International Nuclear Information System (INIS)

    Durham, L. A.; Johnson, R. L.

    2003-01-01

    Traditional approaches to excavation design for sites with radionuclide-contaminated soils generally involve work plans with fixed excavation footprints and post-excavation verification sampling. Recent advancements in real-time data collection systems, combined with data loggers, location control systems, and secure project-support Web sites, allow for an alternative, more precise approach to excavation design and implementation. In this mode, traditional work plans are replaced with dynamic work plans. Excavation efforts are organized by lift, with real-time dig face screening performed and the data for each lift analyzed, before excavation continues. Rather than specifying excavation footprints, dynamic work plans identify the decision logic that will be used to determine footprints based on real-time data collection. The level of investment in excavation support data collection can be balanced against potential cost savings realized through waste stream minimization. Secure project support Web sites ensure that data sets generated during the remediation process are readily accessible to all who need to see them, whether they are on site or not. These include regulators, program managers, and technical support staff. This type of Web site allows for quick problem resolution, increased transparency in field decision making, and more efficient allocation of expensive technical staff time

  20. Identification of critical time-consuming student support activities in e-learning

    NARCIS (Netherlands)

    De Vries, Fred; Kester, Liesbeth; Sloep, Peter; Van Rosmalen, Peter; Pannekeet, Kees; Koper, Rob

    2005-01-01

    Please cite the original publication: De Vries, F., Kester, L., Sloep, P., Van Rosmalen, P., Pannekeet, K., & Koper, R. (2005). Identification of critical time-consuming student support activities in e-learning. Research in Learning Technology (ALT-J), 13(3), 219-229.

  1. A Data Analytical Framework for Improving Real-Time, Decision Support Systems in Healthcare

    Science.gov (United States)

    Yahav, Inbal

    2010-01-01

    In this dissertation we develop a framework that combines data mining, statistics and operations research methods for improving real-time decision support systems in healthcare. Our approach consists of three main concepts: data gathering and preprocessing, modeling, and deployment. We introduce the notion of offline and semi-offline modeling to…

  2. Probing Protein Multidimensional Conformational Fluctuations by Single-Molecule Multiparameter Photon Stamping Spectroscopy

    Science.gov (United States)

    2015-01-01

    Conformational motions of proteins are highly dynamic and intrinsically complex. To capture the temporal and spatial complexity of conformational motions and further to understand their roles in protein functions, an attempt is made to probe multidimensional conformational dynamics of proteins besides the typical one-dimensional FRET coordinate or the projected conformational motions on the one-dimensional FRET coordinate. T4 lysozyme hinge-bending motions between two domains along α-helix have been probed by single-molecule FRET. Nevertheless, the domain motions of T4 lysozyme are rather complex involving multiple coupled nuclear coordinates and most likely contain motions besides hinge-bending. It is highly likely that the multiple dimensional protein conformational motions beyond the typical enzymatic hinged-bending motions have profound impact on overall enzymatic functions. In this report, we have developed a single-molecule multiparameter photon stamping spectroscopy integrating fluorescence anisotropy, FRET, and fluorescence lifetime. This spectroscopic approach enables simultaneous observations of both FRET-related site-to-site conformational dynamics and molecular rotational (or orientational) motions of individual Cy3-Cy5 labeled T4 lysozyme molecules. We have further observed wide-distributed rotational flexibility along orientation coordinates by recording fluorescence anisotropy and simultaneously identified multiple intermediate conformational states along FRET coordinate by monitoring time-dependent donor lifetime, presenting a whole picture of multidimensional conformational dynamics in the process of T4 lysozyme open-close hinge-bending enzymatic turnover motions under enzymatic reaction conditions. By analyzing the autocorrelation functions of both lifetime and anisotropy trajectories, we have also observed the dynamic and static inhomogeneity of T4 lysozyme multidimensional conformational fluctuation dynamics, providing a fundamental

  3. Scandiatransplant acceptable mismatch program (STAMP) a bridge to transplanting highly immunized patients.

    Science.gov (United States)

    Koefoed-Nielsen, P; Weinreich, I; Bengtsson, M; Lauronen, J; Naper, C; Gäbel, M; Sørensen, S S; Wennberg, L; Reisaeter, A V; Møller, B K

    2017-07-01

    Highly immunized patients are a challenge for organ transplantation programs. One way of increasing the likelihood of transplantation in this group of patients is to expand the possible donations by defining acceptable HLA mismatches. In the Scandiatransplant Acceptable Mismatch Program (STAMP), a de-centralized approach has been implemented in 2009. The program has been improved during the years from utilizing HLA-A, -B, -DR matching only to include typing of all deceased donors for HLA-A, -B, -C, -DRB1 and -DQB1. The calculation of a transplantability score (TS) has been introduced in order to take both HLA and AB0 into consideration resulting in a more realistic picture of the transplantability chance. Patients were selected for eligibility and results of immunisation status were prepared in each of the 9 tissue typing laboratories, while access to the program is finally governed by a common steering group of immunologists and clinicians. In the period from March 2009 until February 2015, 96 patients were transplanted within this program. The mean recipient age was 49 years and 57% were females, 30% of the patients were first transplants and of these 93% were females. The majority of the patients had 2-5 HLA-A, -B. -DR mismatches. The allograft survival at 60 months was 79.1%. Applying the TS to the cohort confirmed that patients with a low TS score had longer waiting times. The program has matured during the years and now proves to be a valid approach for transplanting highly immunized patients. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  4. Medical Device Integrated Vital Signs Monitoring Application with Real-Time Clinical Decision Support.

    Science.gov (United States)

    Moqeem, Aasia; Baig, Mirza; Gholamhosseini, Hamid; Mirza, Farhaan; Lindén, Maria

    2018-01-01

    This research involves the design and development of a novel Android smartphone application for real-time vital signs monitoring and decision support. The proposed application integrates market available, wireless and Bluetooth connected medical devices for collecting vital signs. The medical device data collected by the app includes heart rate, oxygen saturation and electrocardiograph (ECG). The collated data is streamed/displayed on the smartphone in real-time. This application was designed by adopting six screens approach (6S) mobile development framework and focused on user-centered approach and considered clinicians-as-a-user. The clinical engagement, consultations, feedback and usability of the application in the everyday practices were considered critical from the initial phase of the design and development. Furthermore, the proposed application is capable to deliver rich clinical decision support in real-time using the integrated medical device data.

  5. [Evaluation of organization of the military medical support in the peace time].

    Science.gov (United States)

    Korshever, N G

    2001-09-01

    The work is devoted to investigation of some theoretical and practical aspects of organizational diagnosis of troops medical support during the peace-time. The analysis of literature, the materials obtained during the practical training of the students of Saratov Military Medical Institute, the expert questioning of the teaching stuff (14 persons) allowed to characterize the difficulties in diagnosis of different objects as well as the qualities necessary for the diagnostician. It also permitted to determine the functions, methods, classification and stages of organizational diagnosis, to substantiate the requirements necessary for evaluation of troops medical support.

  6. Evaluation of Contact Heat Transfer Coefficient and Phase Transformation during Hot Stamping of a Hat-Type Part

    Science.gov (United States)

    Kim, Heung-Kyu; Lee, Seong Hyeon; Choi, Hyunjoo

    2015-01-01

    Using an inverse analysis technique, the heat transfer coefficient on the die-workpiece contact surface of a hot stamping process was evaluated as a power law function of contact pressure. This evaluation was to determine whether the heat transfer coefficient on the contact surface could be used for finite element analysis of the entire hot stamping process. By comparing results of the finite element analysis and experimental measurements of the phase transformation, an evaluation was performed to determine whether the obtained heat transfer coefficient function could provide reasonable finite element prediction for workpiece properties affected by the hot stamping process. PMID:28788046

  7. Nanostructured submicron block copolymer dots by sacrificial stamping: a potential preconcentration platform for locally resolved sensing, chemistry and cellular interactions

    OpenAIRE

    Hou, Peilong; Han, Weijia; Philippi, Michael; Schäfer, Helmut; Steinhart, Martin

    2018-01-01

    Classical contact lithography involves patterning of surfaces by embossing or by transfer of ink. We report direct lithographic transfer of parts of sacrificial stamps onto counterpart surfaces. Using sacrificial stamps consisting of the block copolymer polystyrene-block-poly(2-pyridine) (PS-b-P2VP), we deposited arrays of nanostructured submicron PS-b-P2VP dots with heights of about 100 nm onto silicon wafers and glass slides. The sacrificial PS-b-P2VP stamps were topographically patterned w...

  8. Time and Frequency Activities at the Lithuanian National Time Standard Laboratory

    National Research Council Canada - National Science Library

    Miskinis, Rimantas

    2007-01-01

    ...), the Datum 2001 and SyncServer S250 NTP servers are used. Laboratory activities on coordination of the BALTICTIME project Reinforcing e-Government services in Baltic States through legal and accountable Digital Time Stamps...

  9. Application of statistical distribution theory to launch-on-time for space construction logistic support

    Science.gov (United States)

    Morgenthaler, George W.

    1989-01-01

    The ability to launch-on-time and to send payloads into space has progressed dramatically since the days of the earliest missile and space programs. Causes for delay during launch, i.e., unplanned 'holds', are attributable to several sources: weather, range activities, vehicle conditions, human performance, etc. Recent developments in space program, particularly the need for highly reliable logistic support of space construction and the subsequent planned operation of space stations, large unmanned space structures, lunar and Mars bases, and the necessity of providing 'guaranteed' commercial launches have placed increased emphasis on understanding and mastering every aspect of launch vehicle operations. The Center of Space Construction has acquired historical launch vehicle data and is applying these data to the analysis of space launch vehicle logistic support of space construction. This analysis will include development of a better understanding of launch-on-time capability and simulation of required support systems for vehicle assembly and launch which are necessary to support national space program construction schedules. In this paper, the author presents actual launch data on unscheduled 'hold' distributions of various launch vehicles. The data have been supplied by industrial associate companies of the Center for Space Construction. The paper seeks to determine suitable probability models which describe these historical data and that can be used for several purposes such as: inputs to broader simulations of launch vehicle logistic space construction support processes and the determination of which launch operations sources cause the majority of the unscheduled 'holds', and hence to suggest changes which might improve launch-on-time. In particular, the paper investigates the ability of a compound distribution probability model to fit actual data, versus alternative models, and recommends the most productive avenues for future statistical work.

  10. Time-frequency feature analysis and recognition of fission neutrons signal based on support vector machine

    International Nuclear Information System (INIS)

    Jin Jing; Wei Biao; Feng Peng; Tang Yuelin; Zhou Mi

    2010-01-01

    Based on the interdependent relationship between fission neutrons ( 252 Cf) and fission chain ( 235 U system), the paper presents the time-frequency feature analysis and recognition in fission neutron signal based on support vector machine (SVM) through the analysis on signal characteristics and the measuring principle of the 252 Cf fission neutron signal. The time-frequency characteristics and energy features of the fission neutron signal are extracted by using wavelet decomposition and de-noising wavelet packet decomposition, and then applied to training and classification by means of support vector machine based on statistical learning theory. The results show that, it is effective to obtain features of nuclear signal via wavelet decomposition and de-noising wavelet packet decomposition, and the latter can reflect the internal characteristics of the fission neutron system better. With the training accomplished, the SVM classifier achieves an accuracy rate above 70%, overcoming the lack of training samples, and verifying the effectiveness of the algorithm. (authors)

  11. Review of real-time on-line decision support system RODOS

    International Nuclear Information System (INIS)

    Rossi, J.

    1997-01-01

    RODOS (Real Time Off-site Decision Support System) is a research project, which aims at the development of a versatile decision support system for management of reactor accident off-site consequence assessments in real-time in Europe and in the western parts of the former Soviet Union. The system employs both local and regional environmental radiation monitoring results and meteorological forecasts by means of which the software prepares consistent predictions ranging from the release area to long distances covering all temporal phases of the accident. The data to be obtained from the environment will be processed and based on the mathematical and physical models and it will be prepared to intelligibly form about the prevalent or future environmental radiation situation. The software is intended for operative use of radiation safety authorities. Furthermore, the software is suitable for education and training of rescue field personnel. (refs.)

  12. Exploring the potential of digital resources as a source of social support in first time pregnancy

    Directory of Open Access Journals (Sweden)

    Nikki Newhouse

    2015-10-01

    First-time pregnancy is a time of huge physical and emotional change and women often need support. One way of providing this is to provide wellbeing information. However, pregnant women are bombarded with information, much of it generic, conflicting or anecdotal. Large numbers of women look for information and advice online, increasingly engaging with alternative forms of ‘expert’ information, in the form of other people’s experiences. This context provides a unique opportunity for digital resources to act as preventative medicine: bringing women together in a safe online environment allows them to speak freely, develop practical skills and feel supported as they become parents. This in turn relieves healthcare burden by preventing negative maternal and neonatal outcomes. This project will determine the context-driven user needs and requirements of a unique group of people and demonstrates the importance of a multidisciplinary approach to the development of pragmatic digital health solutions.

  13. Review of real-time on-line decision support system RODOS; RODOS-ohjelman arviointi

    Energy Technology Data Exchange (ETDEWEB)

    Rossi, J. [VTT Energy, Espoo (Finland). Nuclear Energy

    1997-01-01

    RODOS (Real Time Off-site Decision Support System) is a research project, which aims at the development of a versatile decision support system for management of reactor accident off-site consequence assessments in real-time in Europe and in the western parts of the former Soviet Union. The system employs both local and regional environmental radiation monitoring results and meteorological forecasts by means of which the software prepares consistent predictions ranging from the release area to long distances covering all temporal phases of the accident. The data to be obtained from the environment will be processed and based on the mathematical and physical models and it will be prepared to intelligibly form about the prevalent or future environmental radiation situation. The software is intended for operative use of radiation safety authorities. Furthermore, the software is suitable for education and training of rescue field personnel. (refs.).

  14. Workplace lactation support by New Jersey employers following US Reasonable Break Time for Nursing Mothers law.

    Science.gov (United States)

    Bai, Yeon K; Gaits, Susan I; Wunderlich, Shahla M

    2015-02-01

    Returning to an unsupportive work environment has been identified as a major reason for avoidance or early abandonment of breastfeeding among working mothers. This study aimed to examine the nature and extent of accommodations offered to breastfeeding employees among New Jersey employers since the US federal Reasonable Break Time for Nursing Mothers law enactment. A cross-sectional survey was conducted to measure current lactation support in the workplace in New Jersey. Using convenience sampling, the survey was sent to managerial personnel in hospitals and nonhospitals. The level of support was assessed on company policy, lactation room, and room amenity. A composite lactation amenity score was calculated based on responses about lactation room amenities. Respondents (N = 51) completed a 22-item online questionnaire during fall 2011. The support level was compared by type of organization: hospital (n = 37) versus nonhospital (n = 14). The amenity score of hospitals was significantly higher than nonhospitals (1.44 vs 0.45, P = .002). The mean amenity score (score = 0.95) for all employers was far below comprehensive (score = 3.0). Compared to nonhospitals, hospitals were more likely to offer lactation rooms (81% vs 36%, P = .003), have their own breastfeeding policy (35.1% vs 7.1%, P = .01), and provide additional breastfeeding support (eg, education classes, resources; P < .05). Employers, regardless of the type of organization, need to improve their current practices and create equity of lactation support in the workplace. © The Author(s) 2014.

  15. Food and Mood: Just-in-Time Support for Emotional Eating

    OpenAIRE

    Caroll, Erin; Czerwinski, Mary; Roseway, Asta; schraefel, m.c.

    2013-01-01

    Behavior modification in health is difficult, as habitual behaviors are extremely well-learned, by definition. This research is focused on building a persuasive system for behavior modification around emotional eating. In this paper, we make strides towards building a just-in-time support system for emotional eating in three user studies. The first two studies involved participants using a custom mobile phone application for tracking emotions, food, and receiving interventions. We found lots ...

  16. Run-Time and Compiler Support for Programming in Adaptive Parallel Environments

    Directory of Open Access Journals (Sweden)

    Guy Edjlali

    1997-01-01

    Full Text Available For better utilization of computing resources, it is important to consider parallel programming environments in which the number of available processors varies at run-time. In this article, we discuss run-time support for data-parallel programming in such an adaptive environment. Executing programs in an adaptive environment requires redistributing data when the number of processors changes, and also requires determining new loop bounds and communication patterns for the new set of processors. We have developed a run-time library to provide this support. We discuss how the run-time library can be used by compilers of high-performance Fortran (HPF-like languages to generate code for an adaptive environment. We present performance results for a Navier-Stokes solver and a multigrid template run on a network of workstations and an IBM SP-2. Our experiments show that if the number of processors is not varied frequently, the cost of data redistribution is not significant compared to the time required for the actual computation. Overall, our work establishes the feasibility of compiling HPF for a network of nondedicated workstations, which are likely to be an important resource for parallel programming in the future.

  17. MicROS-drt: supporting real-time and scalable data distribution in distributed robotic systems.

    Science.gov (United States)

    Ding, Bo; Wang, Huaimin; Fan, Zedong; Zhang, Pengfei; Liu, Hui

    A primary requirement in distributed robotic software systems is the dissemination of data to all interested collaborative entities in a timely and scalable manner. However, providing such a service in a highly dynamic and resource-limited robotic environment is a challenging task, and existing robot software infrastructure has limitations in this aspect. This paper presents a novel robot software infrastructure, micROS-drt, which supports real-time and scalable data distribution. The solution is based on a loosely coupled data publish-subscribe model with the ability to support various time-related constraints. And to realize this model, a mature data distribution standard, the data distribution service for real-time systems (DDS), is adopted as the foundation of the transport layer of this software infrastructure. By elaborately adapting and encapsulating the capability of the underlying DDS middleware, micROS-drt can meet the requirement of real-time and scalable data distribution in distributed robotic systems. Evaluation results in terms of scalability, latency jitter and transport priority as well as the experiment on real robots validate the effectiveness of this work.

  18. Real-time distributed scheduling algorithm for supporting QoS over WDM networks

    Science.gov (United States)

    Kam, Anthony C.; Siu, Kai-Yeung

    1998-10-01

    Most existing or proposed WDM networks employ circuit switching, typically with one session having exclusive use of one entire wavelength. Consequently they are not suitable for data applications involving bursty traffic patterns. The MIT AON Consortium has developed an all-optical LAN/MAN testbed which provides time-slotted WDM service and employs fast-tunable transceivers in each optical terminal. In this paper, we explore extensions of this service to achieve fine-grained statistical multiplexing with different virtual circuits time-sharing the wavelengths in a fair manner. In particular, we develop a real-time distributed protocol for best-effort traffic over this time-slotted WDM service with near-optical fairness and throughput characteristics. As an additional design feature, our protocol supports the allocation of guaranteed bandwidths to selected connections. This feature acts as a first step towards supporting integrated services and quality-of-service guarantees over WDM networks. To achieve high throughput, our approach is based on scheduling transmissions, as opposed to collision- based schemes. Our distributed protocol involves one MAN scheduler and several LAN schedulers (one per LAN) in a master-slave arrangement. Because of propagation delays and limits on control channel capacities, all schedulers are designed to work with partial, delayed traffic information. Our distributed protocol is of the `greedy' type to ensure fast execution in real-time in response to dynamic traffic changes. It employs a hybrid form of rate and credit control for resource allocation. We have performed extensive simulations, which show that our protocol allocates resources (transmitters, receivers, wavelengths) fairly with high throughput, and supports bandwidth guarantees.

  19. Comparison of the methods for calculating the interfacial heat transfer coefficient in hot stamping

    International Nuclear Information System (INIS)

    Zhao, Kunmin; Wang, Bin; Chang, Ying; Tang, Xinghui; Yan, Jianwen

    2015-01-01

    This paper presents a hot stamping experimentation and three methods for calculating the Interfacial Heat Transfer Coefficient (IHTC) of 22MnB5 boron steel. Comparison of the calculation results shows an average error of 7.5% for the heat balance method, 3.7% for the Beck's nonlinear inverse estimation method (the Beck's method), and 10.3% for the finite-element-analysis-based optimization method (the FEA method). The Beck's method is a robust and accurate method for identifying the IHTC in hot stamping applications. The numerical simulation using the IHTC identified by the Beck's method can predict the temperature field with a high accuracy. - Highlights: • A theoretical formula was derived for direct calculation of IHTC. • The Beck's method is a robust and accurate method for identifying IHTC. • Finite element method can be used to identify an overall equivalent IHTC

  20. Organic thin film transistors and polymer light-emitting diodes patterned by polymer inking and stamping

    International Nuclear Information System (INIS)

    Li Dawen; Guo, L Jay

    2008-01-01

    To fully realize the advantages of organic flexible electronics, patterning is very important. In this paper we show that a purely additive patterning technique, termed polymer inking and stamping, can be used to pattern conductive polymer PEDOT and fabricate sub-micron channel length organic thin film transistors. In addition, we applied the technique to transfer a stack of metal/conjugated polymer in one step and fabricated working polymer light-emitting devices. Based on the polymer inking and stamping technique, a roll-to-roll printing for high throughput fabrication has been demonstrated. We investigated and explained the mechanism of this process based on the interfacial energy consideration and by using the finite element analysis. This technique can be further extended to transfer more complex stacked layer structures, which may benefit the research on patterning on flexible substrates

  1. Silicon micro-masonry using elastomeric stamps for three-dimensional microfabrication

    International Nuclear Information System (INIS)

    Keum, Hohyun; Eisenhaure, Jeffrey D; Kim, Seok; Carlson, Andrew; Ning, Hailong; Mihi, Agustin; Braun, Paul V; Rogers, John A

    2012-01-01

    We present a micromanufacturing method for constructing microsystems, which we term ‘micro-masonry’ based on individual manipulation, influenced by strategies for deterministic materials assembly using advanced forms of transfer printing. Analogous to masonry in construction sites, micro-masonry consists of the preparation, manipulation, and binding of microscale units to assemble microcomponents and microsystems. In this paper, for the purpose of demonstration, we used microtipped elastomeric stamps as manipulators and built three dimensional silicon microstructures. Silicon units of varied shapes were fabricated in a suspended format on donors, retrieved, delivered, and placed on a target location on a receiver using microtipped stamps. Annealing of the assembled silicon units permanently bound them and completed the micro-masonry procedure. (paper)

  2. Solid-state superionic stamping with silver iodide-silver metaphosphate glass

    International Nuclear Information System (INIS)

    Jacobs, K E; Hsu, K H; Han, X; Azeredo, B P; Ferreira, P M; Kumar, A; Fang, N X

    2011-01-01

    This paper demonstrates and analyzes the new use of the glassy solid electrolyte AgI-AgPO 3 for direct nanopatterning of thin silver films with feature resolutions of 30 nm. AgI-AgPO 3 has a high room temperature ionic conductivity with Ag + as the mobile ion, leading to silver etch/patterning rates of up to 20 nm s -1 at an applied bias of 300 mV. The glass can be melt-processed at temperatures below 200 deg. C, providing a facile and economical pathway for creating large area stamps, including the 25 mm 2 stamps shown in this study. Further, the glass is sufficiently transparent to permit integration with existing tools such as aligners and imprint tools, enabling high overlay registration accuracy and facilitating insertion into multi-step fabrication recipes.

  3. Characterization of the interfacial heat transfer coefficient for hot stamping processes

    Science.gov (United States)

    Luan, Xi; Liu, Xiaochuan; Fang, Haomiao; Ji, Kang; El Fakir, Omer; Wang, LiLiang

    2016-08-01

    In hot stamping processes, the interfacial heat transfer coefficient (IHTC) between the forming tools and hot blank is an essential parameter which determines the quenching rate of the process and hence the resulting material microstructure. The present work focuses on the characterization of the IHTC between an aluminium alloy 7075-T6 blank and two different die materials, cast iron (G3500) and H13 die steel, at various contact pressures. It was found that the IHTC between AA7075 and cast iron had values 78.6% higher than that obtained between AA7075 and H13 die steel. Die materials and contact pressures had pronounced effects on the IHTC, suggesting that the IHTC can be used to guide the selection of stamping tool materials and the precise control of processing parameters.

  4. Polymer microlens replication by Nanoimprint Lithography using proton beam fabricated Ni stamp

    International Nuclear Information System (INIS)

    Dutta, R.K.; Kan, J.A. van; Bettiol, A.A.; Watt, F.

    2007-01-01

    It is essential to have a simplified and a rapid method for fabricating micro/nano structures in different kinds of polymeric materials. Though it is possible to fabricate arrays of microlens directly by P beam writing (PBW), it is restricted to a few types of resist materials. Therefore we have fabricated a Ni electroplated metallic stamp comprising of arrays of inverse/negative features of microlenses. The metallic stamp of about 500 μm thick is made on a silicon wafer coated with 10 μm thick polymethylglutarimide (PMGI) resist and the desired structures are written by PBW followed by thermal reflow and Ni electroplating. An array of microlenses is imprinted on a polycarbonate (PC) substrate by the Nanoimprint Lithography (NIL) technique and the replicated microlenses featuring various numerical apertures, diameters and pitches are characterized

  5. Postnatal experiences and support needs of first-time mothers in Singapore: a descriptive qualitative study.

    Science.gov (United States)

    Ong, Shu Fen; Chan, Wai-Chi Sally; Shorey, Shefaly; Chong, Yap Seng; Klainin-Yobas, Piyanee; He, Hong-Gu

    2014-06-01

    to explore first-time mothers' postnatal experiences and support needs after hospital discharge in Singapore. a descriptive qualitative study was adopted in this study. Participants were recruited from a public tertiary hospital in Singapore. Semi-structured interviews were used for data collection and the interview transcripts were analysed using thematic analysis. a purposive sample of 13 English-speaking first-time mothers of age 21 years and above were interviewed within 7-11 days after their hospital discharge. five themes emerged from the thematic analysis: (1) mixed emotions: participants experienced anxiety, labile emotions and stress over infant care; (2) breast feeding concerns: low breast milk supply and physical discomfort; (3) social support: many participants had sufficient social support from family members except their husbands; (4) cultural postnatal practice: majority of participants followed traditional postnatal practices of their culture; and (5) professional support needs: participants needed more information, access to health care services and continuity of care. this study highlighted the importance of providing professional postnatal care to first-time mothers after their discharge from the hospital. Future studies are needed to explore new practices that will enhance the quality of maternity health care and promote positive maternal experiences and well-being in Singapore. there is a need for more innovative advertisement to promote antenatal classes and improve attendance rate. Health care providers should assist women in establishing proper breast feeding techniques. Alternative models of care in the postnatal period, such as midwifery-led care, could facilitate a more woman-centred approach. Postnatal home visits may be considered within the first week of the mothers' hospital discharge, which may be legislated by public health care policies. © 2013 Elsevier Ltd. All rights reserved.

  6. Boron nitride stamp for ultra-violet nanoimprinting lithography fabricated by focused ion beam lithography

    International Nuclear Information System (INIS)

    Altun, Ali Ozhan; Jeong, Jun-Ho; Rha, Jong-Joo; Kim, Ki-Don; Lee, Eung-Sug

    2007-01-01

    Cubic boron nitride (c-BN) is one of the hardest known materials (second after diamond). It has a high level of chemical resistance and high UV transmittance. In this study, a stamp for ultra-violet nanoimprint lithography (UV-NIL) was fabricated using a bi-layered BN film deposited on a quartz substrate. Deposition of the BN was done using RF magnetron sputtering. A hexagonal boron nitride (h-BN) layer was deposited for 30 min before c-BN was deposited for 30 min. The thickness of the film was measured as 160 nm. The phase of the c-BN layer was investigated using Fourier transform infrared (FTIR) spectrometry, and it was found that the c-BN layer has a 40% cubic phase. The deposited film was patterned using focused ion beam (FIB) lithography for use as a UV-NIL stamp. Line patterns were fabricated with the line width and line distance set at 150 and 150 nm, respectively. The patterning process was performed by applying different currents to observe the effect of the current value on the pattern profile. The fabricated patterns were investigated using AFM, and it was found that the pattern fabricated by applying a current value of 50 picoamperes (pA) has a better profile with a 65 nm line depth. The UV transmittance of the 160 nm thick film was measured to be 70-86%. The hardness and modulus of the BN was measured to be 12 and 150 GPa, respectively. The water contact angle of the stamp surface was measured at 75 0 . The stamp was applied to UV-NIL without coating with an anti-adhesion layer. Successful imprinting was proved via scanning electron microscope (SEM) images of the imprinted resin

  7. Food Safety Knowledge and Practices of Older Adult Participants of the Food Stamp Nutrition Education Program

    OpenAIRE

    Rasnake, Crystal Michelle

    2000-01-01

    The purpose of this study was to determine food safety knowledge and practices of older adult participants in the Food Stamp Nutrition Education Program (FSNEP) in Virginia. One hundred and sixty-five FSNEP participants were assigned to two possible intervention groups, group one received the food safety lesson from the Healthy Futures Series currently used in FSNEP, while group two received the food safety lesson plus an additional food safety video. FSNEP participants completed food safet...

  8. Low temperature high density plasma nitriding of stainless steel molds for stamping of oxide glasses

    Directory of Open Access Journals (Sweden)

    Aizawa Tatsuhiko

    2016-01-01

    Full Text Available Various kinds of stainless steels have been widely utilized as a die for mold- and direct-stamping processes of optical oxide glasses. Since they suffered from high temperature transients and thermal cycles in practice, they must be surface-treated by dry and wet coatings, or, by plasma nitriding. Martensitic stainless steel mold was first wet plated by the nickel phosphate (NiP, which was unstable at the high temperature stamping condition; and, was easy to crystalize or to fracture by itself. This issue of nuisance significantly lowered the productivity in fabrication of optical oxide-glass elements. In the present paper, the stainless steel mold was surface-treated by the low-temperature plasma nitriding. The nitrided layer by this surface modification had higher nitrogen solute content than 4 mass%; the maximum solid-solubility of nitrogen is usually 0.1 mass% in the equilibrium phase diagram. Owing to this solid-solution with high nitrogen concentration, the nitrided layer had high hardness over 1400 HV within its thickness of 50 μm without any formation of nitrides after plasma nitriding at 693 K for 14.4 ks. This plasma-nitrided mold was utilized for mold-stamping of two colored oxide glass plates at 833 K; these plates were successfully deformed and joined into a single glass plate by this stamping without adhesion or galling of oxide glasses onto the nitrided mold surface.

  9. Using stamping punch force variation for the identification of changes in lubrication and wear mechanism

    Science.gov (United States)

    Voss, B. M.; Pereira, M. P.; Rolfe, B. F.; Doolan, M. C.

    2017-09-01

    The growth in use of Advanced High Strength Steels in the automotive industry for light-weighting and safety has increased the rates of tool wear in sheet metal stamping. This is an issue that adds significant costs to production in terms of manual inspection and part refinishing. To reduce these costs, a tool condition monitoring system is required and a firm understanding of process signal variation must form the foundation for any such monitoring system. Punch force is a stamping process signal that is widely collected by industrial presses and has been linked closely to part quality and tool condition, making it an ideal candidate as a tool condition monitoring signal. In this preliminary investigation, the variation of punch force due to different lubrication conditions and progressive wear are examined. Linking specific punch force signature changes to developing lubrication and wear events is valuable for die wear and stamping condition monitoring. A series of semi-industrial channel forming trials were conducted under different lubrication regimes and progressive die wear. Punch force signatures were captured for each part and Principal Component Analysis (PCA) was applied to determine the key Principal Components of the signature data sets. These Principal Components were linked to the evolution of friction conditions over the course of the stroke for the different lubrication regimes and mechanism of galling wear. As a result, variation in punch force signatures were correlated to the current mechanism of wear dominant on the formed part; either abrasion or adhesion, and to changes in lubrication mechanism. The outcomes of this study provide important insights into punch force signature variation, that will provide a foundation for future work into the development of die wear and lubrication monitoring systems for sheet metal stamping.

  10. Characteristic times in the English Channel from numerical modelling: supporting decision-making

    Energy Technology Data Exchange (ETDEWEB)

    Perianez, R [Departamento de Fisica Aplicada 1, Universidad de Sevilla, EUITA, Carretera Utrera km 1, 41013 Sevilla (Spain); Miro, C [Departamento de Fisica Aplicada, Facultad de Veterinaria, Universidad de Extremadura, Avenida de la Universidad s/n, 10071 Caceres (Spain)], E-mail: rperianez@us.es, E-mail: cmiro@unex.es

    2009-06-15

    A numerical model that simulates the dispersion of radionuclides in the English Channel has been applied to study the dispersion of conservative and non-conservative radionuclides released from the La Hague nuclear fuel reprocessing plant. The model is based upon previous work and now is able to simulate dispersion over long timescales (decades), explicitly including transport by instantaneous tidal currents and variable wind conditions. Wind conditions are obtained from meteorological statistics using a stochastic method. Outputs from the model are treated using time-series analysis techniques. These techniques allow the determination of characteristic times of the system, transport velocities and dispersion factors. This information may be very useful to support the decision-making process after an emergency situation. Thus, we are proposing that time-series analysis can be integrated with numerical modelling for helping decision-making in response to an accident. The model is first validated through its application to actual releases of {sup 99}Tc and {sup 125}Sb, comparing measured and computed concentrations, and characteristic times for three radionuclides are given next: a perfectly conservative one, a very reactive one ({sup 239,240}Pu) and {sup 137}Cs, which has an intermediate behaviour. Characteristic transport velocities and dispersion factors have been calculated as well. Model results are supported by experimental evidence.

  11. High Resolution Near Real Time Image Processing and Support for MSSS Modernization

    Science.gov (United States)

    Duncan, R. B.; Sabol, C.; Borelli, K.; Spetka, S.; Addison, J.; Mallo, A.; Farnsworth, B.; Viloria, R.

    2012-09-01

    This paper describes image enhancement software applications engineering development work that has been performed in support of Maui Space Surveillance System (MSSS) Modernization. It also includes R&D and transition activity that has been performed over the past few years with the objective of providing increased space situational awareness (SSA) capabilities. This includes Air Force Research Laboratory (AFRL) use of an FY10 Dedicated High Performance Investment (DHPI) cluster award -- and our selection and planned use for an FY12 DHPI award. We provide an introduction to image processing of electro optical (EO) telescope sensors data; and a high resolution image enhancement and near real time processing and summary status overview. We then describe recent image enhancement applications development and support for MSSS Modernization, results to date, and end with a discussion of desired future development work and conclusions. Significant improvements to image processing enhancement have been realized over the past several years, including a key application that has realized more than a 10,000-times speedup compared to the original R&D code -- and a greater than 72-times speedup over the past few years. The latest version of this code maintains software efficiency for post-mission processing while providing optimization for image processing of data from a new EO sensor at MSSS. Additional work has also been performed to develop low latency, near real time processing of data that is collected by the ground-based sensor during overhead passes of space objects.

  12. Associations between Parental and Friend Social Support and Children's Physical Activity and Time Spent outside Playing.

    Science.gov (United States)

    Loucaides, Constantinos A; Tsangaridou, Niki

    2017-01-01

    The purpose of this study was to examine the structural validity of a parent and a child questionnaire that assessed parental and friends' influences on children's physical activity and investigate the associations between the derived factors, physical activity, and time spent outside. Children ( N = 154, mean age = 11.7) and 144 of their parents completed questionnaires assessing parental and friends' influences on children's physical activity. Children wore a pedometer for six days. Exploratory factor analyses revealed four factors for the parental and five for the child's questionnaire that explained 66.71% and 63.85% of the variance, respectively. Five factors were significantly associated with physical activity and five significantly associated with time spent outside. Higher correlations were revealed between "general friend support," "friends' activity norms," and physical activity ( r = 0.343 and 0.333 resp., p friend support" and time spent outside ( r = 0.460, p parental and friends' influences on physical activity from both parents and children may provide a more complete picture of influences. Parents and friends seem to influence children's physical activity behavior and time spent outside, but friends' influences may have a stronger impact on children's behaviors.

  13. Cost-benefit analysis of providing a special subsistence allowance to military personnel who qualify for food stamps

    OpenAIRE

    Becker, Curtis A., Jr.

    2000-01-01

    Approved for public release, distribution is unlimited Recent reports cite that military Food Stamp Program beneficiaries may range from 6,400 to 20,000. The need for food stamps has been attributed to several factors, one of which is the perceived military "pay gap". Although, significant strides have been made in recent years to improve quality of life for our service men and women and their families, the military pay system tends to lag behind the civilian employment cost growth index. ...

  14. Investigations on the Hot Stamping of AW-7921-T4 Alloy Sheet

    Directory of Open Access Journals (Sweden)

    M. Kumar

    2017-01-01

    Full Text Available AW-7xxx alloys have been nowadays considered for greater light weighting potential in automotive industry due to its higher strength compared to AW-5xxx and AW-6xxx alloys. However, due to their lower formability the forming processes are still in development. This paper investigates one such forming process called hot stamping. The investigation started by carrying out hot tensile testing of an AW-7xxx alloy, that is, AW-7921 at temperatures between 350°C and 475°C, to measure the strength and formability. Formability was found to improve with increasing temperature and was sensitive to the strain rate. Dynamic recovery is considered as usual reason for the formability improvement. However, examining the precipitation states of the as-received condition and after hot stamping using differential scanning calorimetry (DSC, the dissolution of precipitates was also believed to contribute to this increase in formability. Following solution heat treatment there was no precipitation during cooling across the cooling rates investigated (5–10°C/s. Samples taken from parts hot stamped at 10 and 20 mm s−1 had similar yield strengths. A 3-step paint baking heat treatment yielded a higher postpaint baking strength than a single step treatment.

  15. Tribological behavior of a new green industrial lubricant for stamping operations - Application to Stainless Steels

    Science.gov (United States)

    Buteri, A.; Borgeot, M.; Roizard, X.; Lallemand, F.; Melot, J.-M.; Morand, L.

    2016-11-01

    Thanks to a fruitful collaboration between different academic and industrial research entities, a new green lubricant solution AFULudine has been developed for stamping operations in substitution to the usual mineral oils, with the idea and the wish to combine different essential properties such as a low environmental impact and ease-of-use according to the market needs and the more and more restrictive environmental legislation (e.g. REACH). Based on the Self-Assembled-Monolayer (SAM) principle and so, on a perfect control of the chemical reaction between the solution and the substrate (grafting of molecules onto the surface), AFULudine offers an efficient technical answer for improving stamping processes. The present study, focused on stainless steel stampings (comparison between a 441-1.4509 grade and a 304-1.4301 grade), investigates the performances of this new green industrial lubricant at different levels: from laboratory tests to industrial conditions through the production of hundreds of parts. Additional results coming from tests made on a rotational pin- on-disk tribometer will allow us to appreciate and retrieve more local information about the tribofilm creation during sliding. Moreover, the comparison with different mineral oils currently used at industrial scale, will strengthen the AFULudine performances. Indeed, this new solution usually outperforms a majority of such oils whatever their viscosity and their own composition: formulation, content of extreme pressure additives (Cl, S, P)...

  16. Martensitic microstructural transformations from the hot stamping, quenching and partitioning process

    International Nuclear Information System (INIS)

    Liu Heping; Jin Xuejun; Dong Han; Shi Jie

    2011-01-01

    Hot stamping, which combines forming and quenching in one process, produces high strength steels with limited ductility because the quenching is uncontrolled. A new processing technique has been proposed in which the hot stamping step is followed by a controlled quenching and partitioning process, producing a microstructure containing retained austenite and martensite. To investigate this microstructure, specimens were heated at a rate of 10 deg. C/s to the austenitizing temperature of 900 deg. C, held for 5 min to eliminate thermal gradients, and cooled at a rate of 50 deg. C/s to a quenching temperature of 300 deg. C, which is between the martensite start temperature and the martensite finish temperatures. The resulting microstructure was examined using optical microscope, scanning electron microscopy and transmission electron microscopy. The material produced contains irregular, fragmented martensite plates, a result of the improved strength of the austenite phase and the constraints imposed by a high dislocation density. - Research Highlights: → A novel heat treatment of advanced high strength steels is proposed. → The processing technique is hot stamping plus quenching and partitioning process. → The material produced contains irregular, fragmented martensite plates. → The reason is strength of austenite phase and constraint of dislocation density.

  17. Causal Analysis to a Subway Accident: A Comparison of STAMP and RAIB

    Directory of Open Access Journals (Sweden)

    Zhou Yao

    2018-01-01

    Full Text Available Accident investigation and analysis after the accident, vital to prevent the occurrence of similar accident and improve the safety of the system. Different methods led to a different understanding of the accident. In this paper, a subway accident was analysed with a systemic accident analysis model – STAMP (System-Theoretic Accident Modelling and Processes. The hierarchical safety control structure was obtained, and the system-level safety constraints were obtained, controllers of the physical layer were analysed one by one, and put forward the relevant safety requirements and constraints, the dynamic analysis of the structure of the safety control is carried out, and the targeted recommendations are pointed out. In comparison with the analysis results obtained by the Rail Accident Investigation Branch (RAIB. Some useful findings have been concluded. STAMP treats safety as a control problem and reduces or eliminates causes of the accident from the controlling perspective. Whereas RAIB obtains causes of the accident by analysing the sequence of events related to the accident and reasons of these events, then chooses one(or moreevent(s as the immediate cause and some of the key events as causal factors. RAIB analysis is based on the sequential event models, but STAMP analysis provides us with a holistic, dynamic way to control system to maintain safety.

  18. Failure Mechanisms of the Protective Coatings for the Hot Stamping Applications

    Science.gov (United States)

    Zhao, Chen

    In the present study, four different nitriding techniques were carried on the ductile irons NAAMS-D6510 and cast steels NAAMS-S0050A, which are widely used stamping die materials; duplex treatments (PVD CrN coating+nitriding) were carried on H13 steels, which are common inserts for the hot stamping dies. Inclined impact-sliding wear tests were performed on the nitriding cases under simulated stamping conditions. Surface profilometer, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) were used to investigate the wear and failure mechanisms of the protective coatings. It was found that the nitrided ductile iron samples performed better than the nitrided cast steel specimens. High temperature inclined impact-sliding wear tests were carried out on the CrN coatings. It was found that the coating performed better at elevated temperature. XPS analysis indicated the top surface layer (about 3-4nm) of the coating was oxidized at 400 °C and formed a Cr2O3 protective film. The in-situ formation of the thin Cr2O3 protective layer likely led to the change of wear mechanisms from severe adhesive failure to mild abrasive wear.

  19. Probabilistic Design in a Sheet Metal Stamping Process under Failure Analysis

    International Nuclear Information System (INIS)

    Buranathiti, Thaweepat; Cao, Jian; Chen, Wei; Xia, Z. Cedric

    2005-01-01

    Sheet metal stamping processes have been widely implemented in many industries due to its repeatability and productivity. In general, the simulations for a sheet metal forming process involve nonlinearity, complex material behavior and tool-material interaction. Instabilities in terms of tearing and wrinkling are major concerns in many sheet metal stamping processes. In this work, a sheet metal stamping process of a mild steel for a wheelhouse used in automobile industry is studied by using an explicit nonlinear finite element code and incorporating failure analysis (tearing and wrinkling) and design under uncertainty. Margins of tearing and wrinkling are quantitatively defined via stress-based criteria for system-level design. The forming process utilizes drawbeads instead of using the blank holder force to restrain the blank. The main parameters of interest in this work are friction conditions, drawbead configurations, sheet metal properties, and numerical errors. A robust design model is created to conduct a probabilistic design, which is made possible for this complex engineering process via an efficient uncertainty propagation technique. The method called the weighted three-point-based method estimates the statistical characteristics (mean and variance) of the responses of interest (margins of failures), and provide a systematic approach in designing a sheet metal forming process under the framework of design under uncertainty

  20. SU-D-9A-03: STAMP: Simulator for Texture Analysis in MRI/PET

    Energy Technology Data Exchange (ETDEWEB)

    Laberge, S; Vallieres, M; Levesque, I R.; El Naqa, I [McGill University, Montreal, QC (Canada)

    2014-06-01

    Purpose: To develop a convenient simulation platform to facilitate PET/MR image analysis with the prospect of gaining a better understanding of the influence of acquisition parameters on PET/MRI textural features. The simulation platform is demonstrated by showing textural variations of a representative case study using different image acquisition parameters. Methods: The simulation platform is composed of MRI simulators JEMRIS and SIMRI to achieve simulations of customized MRI sequences on sample tumor models. The PET simulator GATE is used to get 2D and 3D Monte Carlo acquisitions of voxelized PET sources using a phantom geometry and a customized scanner architecture. The platform incorporates a series of graphical user interfaces written in Matlab. Two GUIs are used to facilitate communication with the simulation executables installed on a computer cluster. A third GUI is used to collect and display the clinical and simulated images, as well as fused PET/MRI images, and perform computation of textural features.To illustrate the capabilities of this platform, one FDG-PET and T1-weighted (T1w) digitized tumor models were generated from clinical images of a soft-tissue sarcoma patient. Numerically simulated MR images were produced using 3 different echo times (TE) and 5 different repetition times (TR). PET 2D images were simulated using an OSEM algorithm with 1 to 32 iterations and a post-reconstruction Gaussian filter of 0, 2, 4 or 6 mm width. Results: STAMP was successfully used to produce numerically simulated FDG-PET and MRI images, and to calculate their corresponding textures. Three typical textures (GLCM-Contrast, GLSZM-ZSV and NGTDM-Coarseness) were found to vary by a range of 45% on average compared to reference scanning conditions in the case of FDG-PET, and by a range of 40% in the case of T1w MRI. Conclusion: We have successfully developed a Matlab-based simulation platform to facilitate PET/MRI texture image analysis for outcome prediction.

  1. Supporting Real-Time Operations and Execution through Timeline and Scheduling Aids

    Science.gov (United States)

    Marquez, Jessica J.; Pyrzak, Guy; Hashemi, Sam; Ahmed, Samia; McMillin, Kevin Edward; Medwid, Joseph Daniel; Chen, Diana; Hurtle, Esten

    2013-01-01

    Since 2003, the NASA Ames Research Center has been actively involved in researching and advancing the state-of-the-art of planning and scheduling tools for NASA mission operations. Our planning toolkit SPIFe (Scheduling and Planning Interface for Exploration) has supported a variety of missions and field tests, scheduling activities for Mars rovers as well as crew on-board International Space Station and NASA earth analogs. The scheduled plan is the integration of all the activities for the day/s. In turn, the agents (rovers, landers, spaceships, crew) execute from this schedule while the mission support team members (e.g., flight controllers) follow the schedule during execution. Over the last couple of years, our team has begun to research and validate methods that will better support users during realtime operations and execution of scheduled activities. Our team utilizes human-computer interaction principles to research user needs, identify workflow processes, prototype software aids, and user test these. This paper discusses three specific prototypes developed and user tested to support real-time operations: Score Mobile, Playbook, and Mobile Assistant for Task Execution (MATE).

  2. A REAL TIME DECISION SUPPORT SYSTEM FOR THE ADJUSTMENT OF SAILBOAT RIGGING

    Directory of Open Access Journals (Sweden)

    Inmaculada Ortigosa

    2016-01-01

    Full Text Available The operational complexity and performance requirements of modern racing yachts demand the use of advanced applications, such as a decision support system (DSS able to assist crew members during navigation. In this article, the authors describe a near-time computational solver as the main piece of a DSS which analyses and monitors the behaviour of sails and rigging. The solver is made up of two different interconnected tools: an iterative Fluid-Structure Interaction algorithm and an advanced Wireless Sensor Network to monitor rigging. The real-time DSS quantifies crew manoeuvres in physical terms, which are reproduced by a simulation program. It can be used in the design phase of sailing yachts and as an aid for real-time boat performance optimisation and accident prevention. This novel DSS is a useful tool for navigation, especially in races.

  3. Real-time decision support in the face of emerging natural hazard events

    DEFF Research Database (Denmark)

    Anders, Annett

    and losses. Motivated by these factors, the present thesis aims at developing a framework for the decision support system for real-time decision making in emerging natural hazard events. The thesis also demonstrates the implementation of the developed framework to illustrate its use and advantages...... turbines, agricultural facilities and offshore platforms. Operators of these facilities are often required to make decisions regarding the continued operations of their facilities in extreme storm events. These decisions, which in the present thesis are called real-time decisions, are often made by a small...... number of people in extremely stressful situations, ad-hoc relying on personal experiences of decision makers. On the other hand, recent advancements of information technology potentially make it possible for decision makers to access various types of information in real-time. Remarkable examples...

  4. RODOS and RESY: two integrated real time on-line decision support systems for nuclear emergencies

    International Nuclear Information System (INIS)

    Ehrhardt, J.; Fischer, F.; Paesler-Sauer, J.; Schuele, O.; Benz, G.; Rafat, M.

    1993-01-01

    Based on the experience gained with the development of the German real-time system RESY for near range and early phase decision support KfK has developed the hardware and software framework of RODOS, the EC real-time on-line decision support system for nuclear emergencies. The first prototype version of RODOS incorporates models for atmospheric dispersion, for external and internal dose and dose-rate assessments, for simulating sheltering, evacuation and milk interdiction, for estimating health effects and economic costs, and for evaluating action alternatives by means of a rule based system containing components of multi-attribute value techniques. The specially designed operating system has been developed on the basis of the client-server model as a transportable package to run on workstations with a standard based UNIX operating system, and an X-Window system. One of its key features is the support of integrated external software products developed by the contractors by providing standardized services, such as system control, data management and graphical presentation. A data base of geographical structures (e.g. landscape, buildings, traffic network) with an accuracy of 30 m stored as vector data and population distribution stored in a 1 kmx1 km grid allows the presentation and evaluation of results down to a high local resolution by a special graphics subsystem. (orig./DG)

  5. Online Support Vector Regression with Varying Parameters for Time-Dependent Data

    International Nuclear Information System (INIS)

    Omitaomu, Olufemi A.; Jeong, Myong K.; Badiru, Adedeji B.

    2011-01-01

    Support vector regression (SVR) is a machine learning technique that continues to receive interest in several domains including manufacturing, engineering, and medicine. In order to extend its application to problems in which datasets arrive constantly and in which batch processing of the datasets is infeasible or expensive, an accurate online support vector regression (AOSVR) technique was proposed. The AOSVR technique efficiently updates a trained SVR function whenever a sample is added to or removed from the training set without retraining the entire training data. However, the AOSVR technique assumes that the new samples and the training samples are of the same characteristics; hence, the same value of SVR parameters is used for training and prediction. This assumption is not applicable to data samples that are inherently noisy and non-stationary such as sensor data. As a result, we propose Accurate On-line Support Vector Regression with Varying Parameters (AOSVR-VP) that uses varying SVR parameters rather than fixed SVR parameters, and hence accounts for the variability that may exist in the samples. To accomplish this objective, we also propose a generalized weight function to automatically update the weights of SVR parameters in on-line monitoring applications. The proposed function allows for lower and upper bounds for SVR parameters. We tested our proposed approach and compared results with the conventional AOSVR approach using two benchmark time series data and sensor data from nuclear power plant. The results show that using varying SVR parameters is more applicable to time dependent data.

  6. Nanofaceting as a stamp for periodic graphene charge carrier modulations

    Czech Academy of Sciences Publication Activity Database

    Vondráček, Martin; Kalita, D.; Kučera, M.; Fekete, Ladislav; Kopeček, Jaromír; Lančok, Ján; Coraux, J.; Bouchiat, V.; Honolka, Jan

    2016-01-01

    Roč. 6, Apr (2016), 1-7, č. článku 23663. ISSN 2045-2322 R&D Projects: GA MŠk LO1409; GA MŠk LM2015088 Grant - others:AV ČR(CZ) Fellowship J. E. Purkyně; SAFMAT(XE) CZ.2.16/3.1.00/22132 Institutional support: RVO:68378271 Keywords : graphene * ARPES * LEED * AFM * copper * nanofaceting Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 4.259, year: 2016

  7. Social networks, time homeless, and social support: A study of men on Skid Row.

    Science.gov (United States)

    Green, Harold D; Tucker, Joan S; Golinelli, Daniela; Wenzel, Suzanne L

    2013-12-18

    Homeless men are frequently unsheltered and isolated, disconnected from supportive organizations and individuals. However, little research has investigated these men's social networks. We investigate the structure and composition of homeless men's social networks, vis-a-vis short- and long-term homelessness with a sample of men drawn randomly from meal lines on Skid Row in Los Angeles. Men continuously homeless for the past six months display networks composed of riskier members when compared to men intermittently homeless during that time. Men who report chronic, long-term homelessness display greater social network fragmentation when compared to non-chronically homeless men. While intermittent homelessness affects network composition in ways that may be addressable with existing interventions, chronic homelessness fragments networks, which may be more difficult to address with those interventions. These findings have implications for access to social support from network members which, in turn, impacts the resources homeless men require from other sources such as the government or NGOs.

  8. Configuration management issues and objectives for a real-time research flight test support facility

    Science.gov (United States)

    Yergensen, Stephen; Rhea, Donald C.

    1988-01-01

    Presented are some of the critical issues and objectives pertaining to configuration management for the NASA Western Aeronautical Test Range (WATR) of Ames Research Center. The primary mission of the WATR is to provide a capability for the conduct of aeronautical research flight test through real-time processing and display, tracking, and communications systems. In providing this capability, the WATR must maintain and enforce a configuration management plan which is independent of, but complimentary to, various research flight test project configuration management systems. A primary WATR objective is the continued development of generic research flight test project support capability, wherein the reliability of WATR support provided to all project users is a constant priority. Therefore, the processing of configuration change requests for specific research flight test project requirements must be evaluated within a perspective that maintains this primary objective.

  9. Use of NASA Near Real-Time and Archived Satellite Data to Support Disaster Assessment

    Science.gov (United States)

    McGrath, Kevin M.; Molthan, Andrew L.; Burks, Jason E.

    2014-01-01

    NASA's Short-term Prediction Research and Transition (SPoRT) Center partners with the NWS to provide near realtime data in support of a variety of weather applications, including disasters. SPoRT supports NASA's Applied Sciences Program: Disasters focus area by developing techniques that will aid the disaster monitoring, response, and assessment communities. SPoRT has explored a variety of techniques for utilizing archived and near real-time NASA satellite data. An increasing number of end-users - such as the NWS Damage Assessment Toolkit (DAT) - access geospatial data via a Web Mapping Service (WMS). SPoRT has begun developing open-standard Geographic Information Systems (GIS) data sets via WMS to respond to end-user needs.

  10. Real-Time Clinical Decision Support System with Data Stream Mining

    Directory of Open Access Journals (Sweden)

    Yang Zhang

    2012-01-01

    Full Text Available This research aims to describe a new design of data stream mining system that can analyze medical data stream and make real-time prediction. The motivation of the research is due to a growing concern of combining software technology and medical functions for the development of software application that can be used in medical field of chronic disease prognosis and diagnosis, children healthcare, diabetes diagnosis, and so forth. Most of the existing software technologies are case-based data mining systems. They only can analyze finite and structured data set and can only work well in their early years and can hardly meet today's medical requirement. In this paper, we describe a clinical-support-system based data stream mining technology; the design has taken into account all the shortcomings of the existing clinical support systems.

  11. Life Goals Over Time Among Homeless Adults in Permanent Supportive Housing.

    Science.gov (United States)

    Wenzel, S L; Rhoades, H; Moore, H; Lahey, J; Henwood, B; La Motte-Kerr, W; Bird, M

    2018-03-14

    Permanent supportive housing (PSH) is a widely-accepted solution to the challenge of chronic homelessness. While housing support and retention, physical health, and healthcare continue to be important for formerly homeless persons in PSH, "higher-order" and humanistic needs such as thriving have received less attention and as a result are less well understood in this population. One important indicator of thriving is the ability to establish and articulate life goals. This study utilizes longitudinal data from 421 formerly homeless adults prior to their move into PSH, and at 3-, 6- and 12-months after move-in (369 respondents completed all four interviews), to examine what life goals are articulated by this population and how those goals change over time. Prior to housing, most respondents articulated housing attainment as their primary life goal, whereas at follow-up interviews health goals, housing relocation, and financial goals became more prevalent. Aspirational goals (e.g., independence, self-improvement, artistic pursuits) were also common, but demonstrated a decrease over time in housing. Relationship goals remained common and consistent over time. Findings indicate that housing is a necessary, but perhaps not sufficient, step for improving thriving among formerly homeless adults. Implications for practice and future research are discussed. © Society for Community Research and Action 2018.

  12. Failure and reliability prediction by support vector machines regression of time series data

    International Nuclear Information System (INIS)

    Chagas Moura, Marcio das; Zio, Enrico; Lins, Isis Didier; Droguett, Enrique

    2011-01-01

    Support Vector Machines (SVMs) are kernel-based learning methods, which have been successfully adopted for regression problems. However, their use in reliability applications has not been widely explored. In this paper, a comparative analysis is presented in order to evaluate the SVM effectiveness in forecasting time-to-failure and reliability of engineered components based on time series data. The performance on literature case studies of SVM regression is measured against other advanced learning methods such as the Radial Basis Function, the traditional MultiLayer Perceptron model, Box-Jenkins autoregressive-integrated-moving average and the Infinite Impulse Response Locally Recurrent Neural Networks. The comparison shows that in the analyzed cases, SVM outperforms or is comparable to other techniques. - Highlights: → Realistic modeling of reliability demands complex mathematical formulations. → SVM is proper when the relation input/output is unknown or very costly to be obtained. → Results indicate the potential of SVM for reliability time series prediction. → Reliability estimates support the establishment of adequate maintenance strategies.

  13. Evaluating Teachers' Support Requests When Just-in-Time Instructional Support is Provided to Introduce a Primary Level Web-Based Reading Program

    Science.gov (United States)

    Wood, Eileen; Anderson, Alissa; Piquette-Tomei, Noella; Savage, Robert; Mueller, Julie

    2011-01-01

    Support requests were documented for 10 teachers (4 kindergarten, 4 grade one, and 2 grade one/two teachers) who received just-in-time instructional support over a 2 1/2 month period while implementing a novel reading software program as part of their literacy instruction. In-class observations were made of each instructional session. Analysis of…

  14. Impact of Si on Microstructure and Mechanical Properties of 22MnB5 Hot Stamping Steel Treated by Quenching & Partitioning (Q&P)

    Science.gov (United States)

    Linke, Bernd M.; Gerber, Thomas; Hatscher, Ansgar; Salvatori, Ilaria; Aranguren, Iñigo; Arribas, Maribel

    2018-01-01

    Based on 22MnB5 hot stamping steel, three model alloys containing 0.5, 0.8, and 1.5 wt pct Si were produced, heat treated by quenching and partitioning (Q&P), and characterized. Aided by DICTRA calculations, the thermal Q&P cycles were designed to fit into industrial hot stamping by keeping partitioning times ≤ 30 seconds. As expected, Si increased the amount of retained austenite (RA) stabilized after final cooling. However, for the intermediate Si alloy the heat treatment exerted a particularly pronounced influence with an RA content three times as high for the one-step process compared to the two-step process. It appeared that 0.8 wt pct Si sufficed to suppress direct cementite formation from within martensite laths but did not sufficiently stabilize carbon-soaked RA at higher temperatures. Tensile and bending tests showed strongly diverging effects of austenite on ductility. Total elongation improved consistently with increasing RA content independently from its carbon content. In contrast, the bending angle was not impacted by high-carbon RA but deteriorated almost linearly with the amount of low-carbon RA.

  15. Knowledge based support for real time application of multiagent control and automation in electric power systems

    DEFF Research Database (Denmark)

    Saleem, Arshad; Nordstrom, Lars; Lind, Morten

    2011-01-01

    This paper presents a mechanism for developing knowledge based support for real time application of multiagent systems (MAS) in control, automation and diagnosis of electric power systems. In particular it presents a way for autonomous agents to utilize a qualitative means-ends based model...... for reasoning about control situations. The proposed mechanism has been used in different scenarios of electric power distribution system protection and control. Results show that agents can use local models of their environment and coordinate with other agents to analyze and understand a disturbance situation...

  16. Taxation – Charges to stamp duty as consideration

    OpenAIRE

    Shardlow, Janice B.

    1998-01-01

    The author examines issues, illustrated by relevant case law, relating to the imposition of a charge to taxation at a fixed point in time by reference to consideration. Article by Janice B. Shardlow (Lecturer, University of Wolverhampton) published in Amicus Curiae - Journal of the Institute of Advanced Legal Studies and its Society for Advanced Legal Studies. The Journal is produced by the Society for Advanced Legal Studies at the Institute of Advanced Legal Studies, University of London.

  17. A nuclear decision support system built with a real-time process control AI shell

    International Nuclear Information System (INIS)

    Nevins, M.A.

    1990-01-01

    Managing large nuclear power plants is generally approached by creating separate management teams to handle major functional areas such as operations, maintenance, training and engineering. While this approach facilitates a general understanding of the specific functions and problem areas of a nuclear plant, such broad definitions diminish the integration of information needed to understand the overall problem domain. One solution utilizes a decision support system that integrates a real-time process control AI shell, relational database manager, graphic depiction of the real-time events, and distributed knowledge bases that reside within each of the departments. The goal is to create a living model between plant components, procedures, tech specs, specific functions, maintenance and training requirements. This paper describes such a model, called Engineering Model and Simulation System (EMASS)

  18. Real Time Monitoring System of Pollution Waste on Musi River Using Support Vector Machine (SVM) Method

    Science.gov (United States)

    Fachrurrozi, Muhammad; Saparudin; Erwin

    2017-04-01

    Real-time Monitoring and early detection system which measures the quality standard of waste in Musi River, Palembang, Indonesia is a system for determining air and water pollution level. This system was designed in order to create an integrated monitoring system and provide real time information that can be read. It is designed to measure acidity and water turbidity polluted by industrial waste, as well as to show and provide conditional data integrated in one system. This system consists of inputting and processing the data, and giving output based on processed data. Turbidity, substances, and pH sensor is used as a detector that produce analog electrical direct current voltage (DC). Early detection system works by determining the value of the ammonia threshold, acidity, and turbidity level of water in Musi River. The results is then presented based on the level group pollution by the Support Vector Machine classification method.

  19. Comparing Transition-Edge Sensor Response Times in a Modified Contact Scheme with Different Support Beams

    Science.gov (United States)

    Beyer, A. D.; Kenyon, M. E.; Bumble, B.; Runyan, M. C.; Echternach, P. E.; Holmes, W. A.; Bock, J. J.; Bradford, C. M.

    2013-01-01

    We present measurements of the thermal conductance, G, and effective time constants, tau, of three transition-edge sensors (TESs) populated in arrays operated from 80-87mK with T(sub C) approximately 120mK. Our TES arrays include several variations of thermal architecture enabling determination of the architecture that demonstrates the minimum noise equivalent power (NEP), the lowest tau and the trade-offs among designs. The three TESs we report here have identical Mo/Cu bilayer thermistors and wiring structures, while the thermal architectures are: 1) a TES with straight support beams of 1mm length, 2) a TES with meander support beams of total length 2mm and with 2 phononfilter blocks per beam, and 3) a TES with meander support beams of total length 2mm and with 6 phonon-filter blocks per beam. Our wiring scheme aims to lower the thermistor normal state resistance R(sub N) and increase the sharpness of the transition alpha=dlogR/dlogT at the transition temperature T(sub C). We find an upper limit of given by (25+/-10), and G values of 200fW/K for 1), 15fW/K for 2), and 10fW/K for 3). The value of alpha can be improved by slightly increasing the length of our thermistors.

  20. A decision support system for real-time hydropower scheduling in a competitive power market environment

    Science.gov (United States)

    Shawwash, Ziad Khaled Elias

    2000-10-01

    The electricity supply market is rapidly changing from a monopolistic to a competitive environment. Being able to operate their system of reservoirs and generating facilities to get maximum benefits out of existing assets and resources is important to the British Columbia Hydro Authority (B.C. Hydro). A decision support system has been developed to help B.C. Hydro operate their system in an optimal way. The system is operational and is one of the tools that are currently used by the B.C. Hydro system operations engineers to determine optimal schedules that meet the hourly domestic load and also maximize the value B.C. Hydro obtains from spot transactions in the Western U.S. and Alberta electricity markets. This dissertation describes the development and implementation of the decision support system in production mode. The decision support system consists of six components: the input data preparation routines, the graphical user interface (GUI), the communication protocols, the hydraulic simulation model, the optimization model, and the results display software. A major part of this work involved the development and implementation of a practical and detailed large-scale optimization model that determines the optimal tradeoff between the long-term value of water and the returns from spot trading transactions in real-time operations. The postmortem-testing phase showed that the gains in value from using the model accounted for 0.25% to 1.0% of the revenues obtained. The financial returns from using the decision support system greatly outweigh the costs of building it. Other benefits are the savings in the time needed to prepare the generation and trading schedules. The system operations engineers now can use the time saved to focus on other important aspects of their job. The operators are currently experimenting with the system in production mode, and are gradually gaining confidence that the advice it provides is accurate, reliable and sensible. The main lesson

  1. Support time-dependent transformations for surveying and GIS : current status and upcoming challenges

    Science.gov (United States)

    Mahmoudabadi, H.; Lercier, D.; Vielliard, S.; Mein, N.; Briggs, G.

    2016-12-01

    The support of time-dependent transformations for surveying and GIS is becoming a critical issue. We need to convert positions from the realizations of the International Terrestrial Reference Frame to any national reference frame. This problem is easy to solve when all of the required information is available. But it becomes really complicated in a worldwide context. We propose an overview of the current ITRF-aligned reference frames and we describe a global solution to support time-dependent transformations between them and the International Terrestrial Reference Frame. We focus on the uncertainties of station velocities used. In a first approximation, we use a global tectonic plate model to calculate point velocities. We show the impact of the velocity model on the coordinate accuracies. Several countries, particularly in active regions, are developing semi-dynamic reference frames. These frames include local displacement models updated regularly and/or after major events (such as earthquakes). Their integration into surveying or GIS applications is an upcoming challenge. We want to encourage the geodetic community to develop and use standard formats.

  2. Prediction of hourly PM2.5 using a space-time support vector regression model

    Science.gov (United States)

    Yang, Wentao; Deng, Min; Xu, Feng; Wang, Hang

    2018-05-01

    Real-time air quality prediction has been an active field of research in atmospheric environmental science. The existing methods of machine learning are widely used to predict pollutant concentrations because of their enhanced ability to handle complex non-linear relationships. However, because pollutant concentration data, as typical geospatial data, also exhibit spatial heterogeneity and spatial dependence, they may violate the assumptions of independent and identically distributed random variables in most of the machine learning methods. As a result, a space-time support vector regression model is proposed to predict hourly PM2.5 concentrations. First, to address spatial heterogeneity, spatial clustering is executed to divide the study area into several homogeneous or quasi-homogeneous subareas. To handle spatial dependence, a Gauss vector weight function is then developed to determine spatial autocorrelation variables as part of the input features. Finally, a local support vector regression model with spatial autocorrelation variables is established for each subarea. Experimental data on PM2.5 concentrations in Beijing are used to verify whether the results of the proposed model are superior to those of other methods.

  3. Methods and tools to support real time risk-based flood forecasting - a UK pilot application

    Directory of Open Access Journals (Sweden)

    Brown Emma

    2016-01-01

    Full Text Available Flood managers have traditionally used probabilistic models to assess potential flood risk for strategic planning and non-operational applications. Computational restrictions on data volumes and simulation times have meant that information on the risk of flooding has not been available for operational flood forecasting purposes. In practice, however, the operational flood manager has probabilistic questions to answer, which are not completely supported by the outputs of traditional, deterministic flood forecasting systems. In a collaborative approach, HR Wallingford and Deltares have developed methods, tools and techniques to extend existing flood forecasting systems with elements of strategic flood risk analysis, including probabilistic failure analysis, two dimensional flood spreading simulation and the analysis of flood impacts and consequences. This paper presents the results of the application of these new operational flood risk management tools to a pilot catchment in the UK. It discusses the problems of performing probabilistic flood risk assessment in real time and how these have been addressed in this study. It also describes the challenges of the communication of risk to operational flood managers and to the general public, and how these new methods and tools can provide risk-based supporting evidence to assist with this process.

  4. Time to Engage? Texting to Support and Enhance First Year Undergraduate Learning

    Directory of Open Access Journals (Sweden)

    Geraldine Jones

    2009-04-01

    Full Text Available In this paper we discuss a case study investigating how the academic and personal development of first year students on an undergraduate sports education degree can be supported and enhanced with mobile SMS communication. SMS-based technologies were introduced in response to students’ particular needs (in transition to Higher Education and characteristics (‘digital natives’. Despite being unaccustomed to using their mobile phones for academic study, students willingly participated in SMS communication with their tutor via a texting management service. Drawing on evidence from two student surveys, focus groups and a tutor’s journal, we illustrate the potential that mobile SMS communication has to link and establish continuity between face to face teaching sessions and online learning activities in the Virtual Learning Environment (VLE. Many students perceived the SMS communication to have had a positive impact on their management of study time. We link our findings with the existing literature and argue that mobile text based communication has the potential to support the development of time management skills, an important component of self regulatory learning, a skill which has been shown to be key in making a successful transition.

  5. Real-time meteorological data flow in support of TVA's radiological emergency plan

    International Nuclear Information System (INIS)

    Hunter, C.H.; Pittman, D.E.; Malo, J.E.

    1985-01-01

    The Tennessee Valley Authority (TVA) presently operates two nuclear power plants - Browns Ferry (3 units) and Sequoyah (2 units). Two additional plants are under construction. These are Watts Bar scheduled for commercial operation later this year, and Bellefonte (2 units), scheduled for operation near the end of the decade. Under regulations promulgated under 10 CFR Part 50, TVA has developed a Radiological Emergency Plan (REP) to facilitate assessment of the effects of a radiological accident at any of the operational plants. As part of the REP, TVA has developed a system for collecting, displaying, and reviewing, and disseminating real-time meteorological information collected at the nuclear plant sites. The flow of this information must be reliable and continuous so that prompt, informed decisions are possible. This system has been designed using guidance provided in applicable Nuclear Regulatory Commission (NRC) documents, most notably Supplement 1 to NUREG-0737 and Regularoty Guide (R.G.) 1.23. This paper presents a brief description of the REP meteorological support. Meteorological support for nuclear plant emergency preparedness at TVA nuclear plants has been provided for several years. The system has undergone numerous changes during this time, reflecting changes in regulatory guidance and experience gained in implementing the system through numerous drills and exercises. A brief discussion of some of this experience is also presented

  6. Real-time 3D radiation risk assessment supporting simulation of work in nuclear environments

    International Nuclear Information System (INIS)

    Szoke, I; Louka, M N; Bryntesen, T R; Bratteli, J; Edvardsen, S T; RøEitrheim, K K; Bodor, K

    2014-01-01

    This paper describes the latest developments at the Institute for Energy Technology (IFE) in Norway, in the field of real-time 3D (three-dimensional) radiation risk assessment for the support of work simulation in nuclear environments. 3D computer simulation can greatly facilitate efficient work planning, briefing, and training of workers. It can also support communication within and between work teams, and with advisors, regulators, the media and public, at all the stages of a nuclear installation’s lifecycle. Furthermore, it is also a beneficial tool for reviewing current work practices in order to identify possible gaps in procedures, as well as to support the updating of international recommendations, dissemination of experience, and education of the current and future generation of workers. IFE has been involved in research and development into the application of 3D computer simulation and virtual reality (VR) technology to support work in radiological environments in the nuclear sector since the mid 1990s. During this process, two significant software tools have been developed, the VRdose system and the Halden Planner, and a number of publications have been produced to contribute to improving the safety culture in the nuclear industry. This paper describes the radiation risk assessment techniques applied in earlier versions of the VRdose system and the Halden Planner, for visualising radiation fields and calculating dose, and presents new developments towards implementing a flexible and up-to-date dosimetric package in these 3D software tools, based on new developments in the field of radiation protection. The latest versions of these 3D tools are capable of more accurate risk estimation, permit more flexibility via a range of user choices, and are applicable to a wider range of irradiation situations than their predecessors. (paper)

  7. Real-time 3D radiation risk assessment supporting simulation of work in nuclear environments.

    Science.gov (United States)

    Szőke, I; Louka, M N; Bryntesen, T R; Bratteli, J; Edvardsen, S T; RøEitrheim, K K; Bodor, K

    2014-06-01

    This paper describes the latest developments at the Institute for Energy Technology (IFE) in Norway, in the field of real-time 3D (three-dimensional) radiation risk assessment for the support of work simulation in nuclear environments. 3D computer simulation can greatly facilitate efficient work planning, briefing, and training of workers. It can also support communication within and between work teams, and with advisors, regulators, the media and public, at all the stages of a nuclear installation's lifecycle. Furthermore, it is also a beneficial tool for reviewing current work practices in order to identify possible gaps in procedures, as well as to support the updating of international recommendations, dissemination of experience, and education of the current and future generation of workers.IFE has been involved in research and development into the application of 3D computer simulation and virtual reality (VR) technology to support work in radiological environments in the nuclear sector since the mid 1990s. During this process, two significant software tools have been developed, the VRdose system and the Halden Planner, and a number of publications have been produced to contribute to improving the safety culture in the nuclear industry.This paper describes the radiation risk assessment techniques applied in earlier versions of the VRdose system and the Halden Planner, for visualising radiation fields and calculating dose, and presents new developments towards implementing a flexible and up-to-date dosimetric package in these 3D software tools, based on new developments in the field of radiation protection. The latest versions of these 3D tools are capable of more accurate risk estimation, permit more flexibility via a range of user choices, and are applicable to a wider range of irradiation situations than their predecessors.

  8. Coarse Resolution SAR Imagery to Support Flood Inundation Models in Near Real Time

    Science.gov (United States)

    Di Baldassarre, Giuliano; Schumann, Guy; Brandimarte, Luigia; Bates, Paul

    2009-11-01

    In recent years, the availability of new emerging data (e.g. remote sensing, intelligent wireless sensors, etc) has led to a sudden shift from a data-sparse to a data-rich environment for hydrological and hydraulic modelling. Furthermore, the increased socioeconomic relevance of river flood studies has motivated the development of complex methodologies for the simulation of the hydraulic behaviour of river systems. In this context, this study aims at assessing the capability of coarse resolution SAR (Synthetic Aperture Radar) imagery to support and quickly validate flood inundation models in near real time. A hydraulic model of a 98km reach of the River Po (Italy), previously calibrated on a high-magnitude flood event with extensive and high quality field data, is tested using a SAR flood image, acquired and processed in near real time, during the June 2008 low-magnitude event. Specifically, the image is an acquisition by the ENVISAT-ASAR sensor in wide swath mode and has been provided through ESA (European Space Agency) Fast Registration system at no cost 24 hours after the acquisition. The study shows that the SAR image enables validation and improvement of the model in a time shorter than the flood travel time. This increases the reliability of model predictions (e.g. water elevation and inundation width along the river reach) and, consequently, assists flood management authorities in undertaking the necessary prevention activities.

  9. Predicting Taxi-Out Time at Congested Airports with Optimization-Based Support Vector Regression Methods

    Directory of Open Access Journals (Sweden)

    Guan Lian

    2018-01-01

    Full Text Available Accurate prediction of taxi-out time is significant precondition for improving the operationality of the departure process at an airport, as well as reducing the long taxi-out time, congestion, and excessive emission of greenhouse gases. Unfortunately, several of the traditional methods of predicting taxi-out time perform unsatisfactorily at congested airports. This paper describes and tests three of those conventional methods which include Generalized Linear Model, Softmax Regression Model, and Artificial Neural Network method and two improved Support Vector Regression (SVR approaches based on swarm intelligence algorithm optimization, which include Particle Swarm Optimization (PSO and Firefly Algorithm. In order to improve the global searching ability of Firefly Algorithm, adaptive step factor and Lévy flight are implemented simultaneously when updating the location function. Six factors are analysed, of which delay is identified as one significant factor in congested airports. Through a series of specific dynamic analyses, a case study of Beijing International Airport (PEK is tested with historical data. The performance measures show that the proposed two SVR approaches, especially the Improved Firefly Algorithm (IFA optimization-based SVR method, not only perform as the best modelling measures and accuracy rate compared with the representative forecast models, but also can achieve a better predictive performance when dealing with abnormal taxi-out time states.

  10. Fire Engine Support and On-scene Time in Prehospital Stroke Care - A Prospective Observational Study.

    Science.gov (United States)

    Puolakka, Tuukka; Väyrynen, Taneli; Erkkilä, Elja-Pekka; Kuisma, Markku

    2016-06-01

    Introduction On-scene time (OST) previously has been shown to be a significant component of Emergency Medical Services' (EMS') operational delay in acute stroke. Since stroke patients are managed routinely by two-person ambulance crews, increasing the number of personnel available on the scene is a possible method to improve their performance. Hypothesis Using fire engine crews to support ambulances on the scene in acute stroke is hypothesized to be associated with a shorter OST. All patients transported to hospital as thrombolysis candidates during a one-year study period were registered by the ambulance crews using a case report form that included patient characteristics and operational EMS data. Seventy-seven patients (41 [53%] male; mean age of 68.9 years [SD=15]; mean Glasgow Coma Score [GCS] of 15 points [IQR=14-15]) were eligible for the study. Forty-five cases were managed by ambulance and fire engine crews together and 32 by the ambulance crews alone. The median ambulance response time was seven minutes (IQR=5-10) and the fire engine response time was six minutes (IQR=5-8). The number of EMS personnel on the scene was six (IQR=5-7) and two (IQR=2-2), and the OST was 21 minutes (IQR=18-26) and 24 minutes (IQR=20-32; P =.073) for the groups, respectively. In a following regression analysis, using stroke as the dispatch code was the only variable associated with short (engine crews to support ambulances in acute stroke care was not associated with a shorter on-scene stay when compared to standard management by two-person ambulance crews alone. Using stroke as the dispatch code was the only variable that was associated independently with a short OST. Puolakka T , Väyrynen T , Erkkilä E-P , Kuisma M . Fire engine support and on-scene time in prehospital stroke care - a prospective observational study. Prehosp Disaster Med. 2016;31(3):278-281.

  11. Real-Time Science Operations to Support a Lunar Polar Volatiles Rover Mission

    Science.gov (United States)

    Heldmann, Jennifer L.; Colaprete, Anthony; Elphic, Richard C.; Mattes, Greg; Ennico, Kimberly; Fritzler, Erin; Marinova, Margarita M.; McMurray, Robert; Morse, Stephanie; Roush, Ted L.; hide

    2014-01-01

    Future human exploration of the Moon will likely rely on in situ resource utilization (ISRU) to enable long duration lunar missions. Prior to utilizing ISRU on the Moon, the natural resources (in this case lunar volatiles) must be identified and characterized, and ISRU demonstrated on the lunar surface. To enable future uses of ISRU, NASA and the CSA are developing a lunar rover payload that can (1) locate near subsurface volatiles, (2) excavate and analyze samples of the volatile-bearing regolith, and (3) demonstrate the form, extractability and usefulness of the materials. Such investigations are important both for ISRU purposes and for understanding the scientific nature of these intriguing lunar volatile deposits. Temperature models and orbital data suggest near surface volatile concentrations may exist at briefly lit lunar polar locations outside persistently shadowed regions. A lunar rover could be remotely operated at some of these locations for the approx. 2-14 days of expected sunlight at relatively low cost. Due to the limited operational time available, both science and rover operations decisions must be made in real time, requiring immediate situational awareness, data analysis, and decision support tools. Given these constraints, such a mission requires a new concept of operations. In this paper we outline the results and lessons learned from an analog field campaign in July 2012 which tested operations for a lunar polar rover concept. A rover was operated in the analog environment of Hawaii by an off-site Flight Control Center, a rover navigation center in Canada, a Science Backroom at NASA Ames Research Center in California, and support teams at NASA Johnson Space Center in Texas and NASA Kennedy Space Center in Florida. We find that this type of mission requires highly efficient, real time, remotely operated rover operations to enable low cost, scientifically relevant exploration of the distribution and nature of lunar polar volatiles. The field

  12. Timing of organogenesis support basal position of turtles in the amniote tree of life

    Directory of Open Access Journals (Sweden)

    Sánchez-Villagra Marcelo R

    2009-04-01

    Full Text Available Abstract Background The phylogenetic position of turtles is the most disputed aspect in the reconstruction of the land vertebrate tree of life. This controversy has arisen after many different kinds and revisions of investigations of molecular and morphological data. Three main hypotheses of living sister-groups of turtles have resulted from them: all reptiles, crocodiles + birds or squamates + tuatara. Although embryology has played a major role in morphological studies of vertebrate phylogeny, data on developmental timing have never been examined to explore and test the alternative phylogenetic hypotheses. We conducted a comprehensive study of published and new embryological data comprising 15 turtle and eight tetrapod species belonging to other taxa, integrating for the first time data on the side-necked turtle clade. Results The timing of events in organogenesis of diverse character complexes in all body regions is not uniform across amniotes and can be analysed using a parsimony-based method. Changes in the relative timing of particular events diagnose many clades of amniotes and include a phylogenetic signal. A basal position of turtles to the living saurian clades is clearly supported by timing of organogenesis data. Conclusion The clear signal of a basal position of turtles provided by heterochronic data implies significant convergence in either molecular, adult morphological or developmental timing characters, as only one of the alternative solutions to the phylogenetic conundrum can be right. The development of a standard reference series of embryological events in amniotes as presented here should enable future improvements and expansion of sampling and thus the examination of other hypotheses about phylogeny and patterns of the evolution of land vertebrate development.

  13. Data forwarding mechanism for supporting real-time services during relocations in UMTS systems

    Science.gov (United States)

    Cai, Wei; Liao, Xianglong; Zheng, Liang; Liu, Zehong

    2004-04-01

    To minimize the interruption during the handovers or relocations invoked by subscribers moving is a very critical factor to enhance the performance of the UMTS systems. We know that the 2G systems have been optimized to minimize the interruption of speech during handovers by two main technologies: one is the bi-casting for the DL traffic and the other is the fast radio resynchronization by the UE for the UL traffic. In the UMTS systems, we have also implemented lossless relocations for non real-time services with high reliability by data buffering in the source RNC and target RNC for the UE. However, the UMTS systems support four QoS classes traffic flow: conversational class, streaming class, interactive class and background class. The main distinguishing factor between these QoS classes is how delay sensitive the traffic is: Conversational and Streaming classes are mainly used to carry real-time traffic flows, like video telephony, interactive and background classes are mainly used by traditional Internet applications like WWW, E-mail and FTP. It"s essential to provide the solutions for supporting real-time services to meet the requirement for QoS in UMTS systems. Apparently, the Data buffering mechanism is not adapted to real-time services because of it"s delay may exceed the basic requirement for real-time services. Under this background, the paper discussed two data forwarding solutions for real-time services from the PS domain in the UMTS systems: packet duplication and Core Network bi-casting. The former mechanism does not require any new procedures, messages nor information elements. The later mechanism requires that the GGSN or SGSN is able to bi-cast the DL traffic to the target RNC according to the relocations involving two SGSNs or just involving one SGSN. It also implicitly shows that we need change procedures at the nodes SGSN, GGSN and RNC which are involved in the relocation procedure based on existing procedures that we have already designed if

  14. Use of real-time tools to support field operations of NSF's Lower Atmosphere Observing Facilities

    Science.gov (United States)

    Daniels, M.; Stossmeister, G.; Johnson, E.; Martin, C.; Webster, C.; Dixon, M.; Maclean, G.

    2012-12-01

    NCAR's Earth Observing Laboratory (EOL) operates Lower Atmosphere Observing Facilities (LAOF) for the scientific community, under sponsorship of the National Science Foundation. In order to obtain the highest quality dataset during field campaigns, real-time decision-making critically depends on the availability of timely data and reliable communications between field operations staff and instrument operators. EOL incorporates the latest technologies to monitor the health of instrumentation, facilitate remote operations of instrumentation and keep project participants abreast of changing conditions in the field. As the availability of bandwidth on mobile communication networks and the capabilities of their associated devices (smart phone, tablets, etc.) improved, so has the ability of researchers to respond to rapidly changing conditions and coordinate ever more detailed measurements from multiple remote fixed, portable and airborne platforms. This presentation will describe several new tools that EOL is making available to project investigators and how these tools are being used in a mobile computing environment to support enhanced data collection during field campaigns. LAOF platforms such as radars, aircraft, sondes, balloons and surface stations all rely on displays of real-time data for their operations. Data from sondes are ingested into the Global Telecommunications System (GTS) for assimilation into regional forecasting models that help guide project operations. Since many of EOL's projects occur around the globe and at the same time instrument complexity has increased, automated monitoring of instrumentation platforms and systems has become essential. Tools are being developed to allow remote instrument control of our suite of observing systems where feasible. The Computing, Data and Software (CDS) Facility of EOL develops and supports a Field Catalog used in field campaigns for nearly two decades. Today, the Field Catalog serves as a hub for the

  15. Deriving Tools from Real-time Runs: A New CCMC Support for SEC and AFWA

    Science.gov (United States)

    Hesse, Michael; Rastatter, Lutz; MacNeice, Peter; Kuznetsova, Masha

    2008-01-01

    The Community Coordinated Modeling Center (CCMC) is a US inter-agency activity aiming at research in support of the generation of advanced space weather models. As one of its main functions. the CCMC provides to researchers the use of space science models, even if they are not model owners themselves. The second focus of CCMC activities is on validation and verification of space weather models. and on the transition of appropriate models to space weather forecast centers. As part of the latter activity. the CCMC develops real-time simulation systems that stress models through routine execution. A by-product of these real-time calculations is the ability to derive model products, which may be useful for space weather operators. After consultations with NOA/SEC and with AFWA, CCMC has developed a set of tools as a first step to make real-time model output useful to forecast centers. In this presentation, we will discuss the motivation for this activity, the actions taken so far, and options for future tools from model output.

  16. Rubber stamp templates for improving clinical documentation: A paper-based, m-Health approach for quality improvement in low-resource settings.

    Science.gov (United States)

    Kleczka, Bernadette; Musiega, Anita; Rabut, Grace; Wekesa, Phoebe; Mwaniki, Paul; Marx, Michael; Kumar, Pratap

    2018-06-01

    The United Nations' Sustainable Development Goal #3.8 targets 'access to quality essential healthcare services'. Clinical practice guidelines are an important tool for ensuring quality of clinical care, but many challenges prevent their use in low-resource settings. Monitoring the use of guidelines relies on cumbersome clinical audits of paper records, and electronic systems face financial and other limitations. Here we describe a unique approach to generating digital data from paper using guideline-based templates, rubber stamps and mobile phones. The Guidelines Adherence in Slums Project targeted ten private sector primary healthcare clinics serving informal settlements in Nairobi, Kenya. Each clinic was provided with rubber stamp templates to support documentation and management of commonly encountered outpatient conditions. Participatory design methods were used to customize templates to the workflows and infrastructure of each clinic. Rubber stamps were used to print templates into paper charts, providing clinicians with checklists for use during consultations. Templates used bubble format data entry, which could be digitized from images taken on mobile phones. Besides rubber stamp templates, the intervention included booklets of guideline compilations, one Android phone for digitizing images of templates, and one data feedback/continuing medical education session per clinic each month. In this paper we focus on the effect of the intervention on documentation of three non-communicable diseases in one clinic. Seventy charts of patients enrolled in the chronic disease program (hypertension/diabetes, n=867; chronic respiratory diseases, n=223) at one of the ten intervention clinics were sampled. Documentation of each individual patient encounter in the pre-intervention (January-March 2016) and post-intervention period (May-July) was scored for information in four dimensions - general data, patient assessment, testing, and management. Control criteria included

  17. Real-time support of pediatric diabetes self-care by a transport team.

    Science.gov (United States)

    Franklin, Brandi E; Crisler, S Crile; Shappley, Rebekah; Armour, Meri M; McCommon, Dana T; Ferry, Robert J

    2014-01-01

    OBJECTIVE The study seeks to improve access for underserved patients via novel integration of Pedi-Flite (a critical care transport team) and to validate whether this safely enhances diabetes care and effectively expands the endocrine workforce. RESEARCH DESIGN AND METHODS The study retrospectively analyzed pager service use in a cohort of established diabetic patients (n = 979) after inception of Pedi-Flite support. Outcomes included incidence and severity of recurrent diabetic ketoacidosis (DKA) and cost savings generated from reduced referrals to the emergency department (ED) and on-call endocrinologist. We generated descriptive statistics to characterize the study population and ED visits for DKA and constructed logistic regression models to examine associations of pager use and likelihood of ED visitation and nonelective inpatient admission from an ED for DKA. RESULTS Pager users comprised 30% of the patient population. They were younger but had more established diabetes than nonusers. While pager users were 2.75 times more likely than nonusers to visit the ED for DKA (P management models supported by allied health personnel.

  18. Real-Time Support of Pediatric Diabetes Self-Care by a Transport Team

    Science.gov (United States)

    Franklin, Brandi E.; Crisler, S. Crile; Shappley, Rebekah; Armour, Meri M.; McCommon, Dana T.; Ferry, Robert J.

    2014-01-01

    OBJECTIVE The study seeks to improve access for underserved patients via novel integration of Pedi-Flite (a critical care transport team) and to validate whether this safely enhances diabetes care and effectively expands the endocrine workforce. RESEARCH DESIGN AND METHODS The study retrospectively analyzed pager service use in a cohort of established diabetic patients (n = 979) after inception of Pedi-Flite support. Outcomes included incidence and severity of recurrent diabetic ketoacidosis (DKA) and cost savings generated from reduced referrals to the emergency department (ED) and on-call endocrinologist. We generated descriptive statistics to characterize the study population and ED visits for DKA and constructed logistic regression models to examine associations of pager use and likelihood of ED visitation and nonelective inpatient admission from an ED for DKA. RESULTS Pager users comprised 30% of the patient population. They were younger but had more established diabetes than nonusers. While pager users were 2.75 times more likely than nonusers to visit the ED for DKA (P management models supported by allied health personnel. PMID:23959568

  19. Fast Mapping Across Time: Memory Processes Support Children's Retention of Learned Words

    Directory of Open Access Journals (Sweden)

    Haley eVlach

    2012-02-01

    Full Text Available Children's remarkable ability to map linguistic labels to objects in the world is referred to as fast mapping. The current study examined children's (N = 216 and adults’ (N = 54 retention of fast-mapped words over time (immediately, after a 1 week delay, and after a 1 month delay. The fast mapping literature often characterizes children's retention of words as consistently high across timescales. However, the current study demonstrates that learners forget word mappings at a rapid rate. Moreover, these patterns of forgetting parallel forgetting functions of domain general memory processes. Memory processes are critical to children's word learning and the role of one such process, forgetting, is discussed in detail—forgetting supports both word mapping and the generalization of words and categories.

  20. Local Adaptive Control of Solar Photovoltaics and Electric Water Heaters for Real-time Grid Support

    DEFF Research Database (Denmark)

    Bhattarai, Bishnu Prasad; Mendaza, Iker Diaz de Cerio; Bak-Jensen, Birgitte

    2016-01-01

    Overvoltage (OV) in a low voltage distribution network is one of the foremost issues observed even under moderate penetration of rooftop solar photovoltaics (PVs). Similarly, grid under-voltage (UV) is foreseen as a potential issue resulting from increased integration of large flexible loads......, such as electric vehicles, electric water heaters (EWHs) etc. An adaptive control using only local measurements for the EWHs and PVs is proposed in this study to alleviate OV as well as UV issues. The adaptive control is designed such that it monitors the voltage at the point of connection and adjusts active...... and reactive power injection/consumptions of the EWHs and PVs following the voltage violations. To effectively support the network in real-time, the controller allows EWHs to operate prior to PVs in OV and after the PVs in UV violations. The effectiveness of the proposed control strategy is demonstrated...

  1. Predicting Jakarta composite index using hybrid of fuzzy time series and support vector regression models

    Science.gov (United States)

    Febrian Umbara, Rian; Tarwidi, Dede; Budi Setiawan, Erwin

    2018-03-01

    The paper discusses the prediction of Jakarta Composite Index (JCI) in Indonesia Stock Exchange. The study is based on JCI historical data for 1286 days to predict the value of JCI one day ahead. This paper proposes predictions done in two stages., The first stage using Fuzzy Time Series (FTS) to predict values of ten technical indicators, and the second stage using Support Vector Regression (SVR) to predict the value of JCI one day ahead, resulting in a hybrid prediction model FTS-SVR. The performance of this combined prediction model is compared with the performance of the single stage prediction model using SVR only. Ten technical indicators are used as input for each model.

  2. Fast Mapping Across Time: Memory Processes Support Children's Retention of Learned Words.

    Science.gov (United States)

    Vlach, Haley A; Sandhofer, Catherine M

    2012-01-01

    Children's remarkable ability to map linguistic labels to referents in the world is commonly called fast mapping. The current study examined children's (N = 216) and adults' (N = 54) retention of fast-mapped words over time (immediately, after a 1-week delay, and after a 1-month delay). The fast mapping literature often characterizes children's retention of words as consistently high across timescales. However, the current study demonstrates that learners forget word mappings at a rapid rate. Moreover, these patterns of forgetting parallel forgetting functions of domain-general memory processes. Memory processes are critical to children's word learning and the role of one such process, forgetting, is discussed in detail - forgetting supports extended mapping by promoting the memory and generalization of words and categories.

  3. Coordination of atmospheric dispersion activities for the real-time decision support system RODOS

    International Nuclear Information System (INIS)

    Mikkelsen, T.

    1997-05-01

    This projects task has been to coordinate activities among the RODOS Atmospheric Dispersion sub-group A participants, with the overall objective of developing and integrating an atmospheric transport and dispersion module for the joint European Real-time On-line DecisiOn Support system RODOS headed by FZK (formerly KfK), Germany. The project's final goal is the establishment of a fully operational, system-integrated atmospheric transport module for the RODOS system by year 2000, capable of consistent now- and forecasting of radioactive airborne spread over all types of terrain and on all scales of interest, including in particular complex terrain and the different scales of operation, such as the local, the national and the European scale. (au)

  4. Over, under, or about right: misperceptions of body weight among food stamp participants.

    Science.gov (United States)

    Ver Ploeg, Michele L; Chang, Hung-Hao; Lin, Biing-Hwan

    2008-09-01

    The purpose of this research was to investigate the associations between misperception of body weight and sociodemographic factors such as food stamp participation status, income, education, and race/ethnicity. National Health and Nutrition Examination Survey (NHANES) data from 1999-2004 and multivariate logistic regression are used to estimate how sociodemographic factors are associated with (i) the probability that overweight adults misperceive themselves as healthy weight; (ii) the probability that healthy-weight adults misperceive themselves as underweight; and (iii) the probability that healthy-weight adults misperceive themselves as overweight. NHANES data are representative of the US civilian noninstitutionalized population. The analysis included 4,362 men and 4,057 women. BMI derived from measured weight and height was used to classify individuals as healthy weight or overweight. These classifications were compared with self-reported categorical weight status. We find that differences across sociodemographic characteristics in the propensity to underestimate or overestimate weight status were more pronounced for women than for men. Overweight female food stamp participants were more likely to underestimate weight status than income-eligible nonparticipants. Among healthy-weight and overweight women, non-Hispanic black and Mexican-American women, and women with less education were more likely to underestimate actual weight status. We found few differences across sociodemographic characteristics for men. Misperceptions of weight are common among both overweight and healthy-weight individuals and vary across socioeconomic and demographic groups. The nutrition education component of the Food Stamp Program could increase awareness of healthy body weight among participants.

  5. Kinesthetic Astronomy: Significant Upgrades to the Sky Time Lesson that Support Student Learning

    Science.gov (United States)

    Morrow, C. A.; Zawaski, M.

    2004-12-01

    This paper will report on a significant upgrade to the first in a series of innovative, experiential lessons we call Kinesthetic Astronomy. The Sky Time lesson reconnects students with the astronomical meaning of the day, year, and seasons. Like all Kinesthetic Astronomy lessons, it teaches basic astronomical concepts through choreographed bodily movements and positions that provide educational sensory experiences. They are intended for sixth graders up through adult learners in both formal and informal educational settings. They emphasize astronomical concepts and phenomenon that people can readily encounter in their "everyday" lives such as time, seasons, and sky motions of the Sun, Moon, stars, and planets. Kinesthetic Astronomy lesson plans are fully aligned with national science education standards, both in content and instructional practice. Our lessons offer a complete learning cycle with written assessment opportunities now embedded throughout the lesson. We have substantially strengthened the written assessment options for the Sky Time lesson to help students translate their kinesthetic and visual learning into the verbal-linguistic and mathematical-logical realms of expression. Field testing with non-science undergraduates, middle school science teachers and students, Junior Girl Scouts, museum education staff, and outdoor educators has been providing evidence that Kinesthetic Astronomy techniques allow learners to achieve a good grasp of concepts that are much more difficult to learn in more conventional ways such as via textbooks or even computer animation. Field testing of the Sky Time lesson has also led us to significant changes from the previous version to support student learning. We will report on the nature of these changes.

  6. Near Real-Time Dust Aerosol Detection with Support Vector Machines for Regression

    Science.gov (United States)

    Rivas-Perea, P.; Rivas-Perea, P. E.; Cota-Ruiz, J.; Aragon Franco, R. A.

    2015-12-01

    Remote sensing instruments operating in the near-infrared spectrum usually provide the necessary information for further dust aerosol spectral analysis using statistical or machine learning algorithms. Such algorithms have proven to be effective in analyzing very specific case studies or dust events. However, very few make the analysis open to the public on a regular basis, fewer are designed specifically to operate in near real-time to higher resolutions, and almost none give a global daily coverage. In this research we investigated a large-scale approach to a machine learning algorithm called "support vector regression". The algorithm uses four near-infrared spectral bands from NASA MODIS instrument: B20 (3.66-3.84μm), B29 (8.40-8.70μm), B31 (10.78-11.28μm), and B32 (11.77-12.27μm). The algorithm is presented with ground truth from more than 30 distinct reported dust events, from different geographical regions, at different seasons, both over land and sea cover, in the presence of clouds and clear sky, and in the presence of fires. The purpose of our algorithm is to learn to distinguish the dust aerosols spectral signature from other spectral signatures, providing as output an estimate of the probability of a data point being consistent with dust aerosol signatures. During modeling with ground truth, our algorithm achieved more than 90% of accuracy, and the current live performance of the algorithm is remarkable. Moreover, our algorithm is currently operating in near real-time using NASA's Land, Atmosphere Near real-time Capability for EOS (LANCE) servers, providing a high resolution global overview including 64, 32, 16, 8, 4, 2, and 1km. The near real-time analysis of our algorithm is now available to the general public at http://dust.reev.us and archives of the results starting from 2012 are available upon request.

  7. A Near Real-time Decision Support System Improving Forest Management in the Tropics

    Science.gov (United States)

    Tabor, K.; Musinsky, J.; Ledezma, J.; Rasolohery, A.; Mendoza, E.; Kistler, H.; Steininger, M.; Morton, D. C.; Melton, F. S.; Manwell, J.; Koenig, K.

    2013-12-01

    Conservation International (CI) has a decade of experience developing near real-time fire and deforestation monitoring and forecasting systems that channel monitoring information from satellite observations directly to national and sub-national government agencies, Non-Government Organizations (NGOs), and local communities. These systems are used to strengthen forest surveillance and monitoring, fire management and prevention, protected areas management and sustainable land use planning. With support from a NASA Wildland Fires grant, in September 2013 CI will launch a brand new near real-time alert system (FIRECAST) to better meet the outstanding needs and challenges users face in addressing ecosystem degradation from wildland fire and illegal forest activities. Outreach efforts and user feedback have indicated the need for seasonal fire forecasts for effective land use planning, faster alert delivery to enhance response to illegal forest activities, and expanded forest monitoring capabilities that enable proactive responses and that strengthen forest conservation and sustainable development actions. The new FIRECAST system addresses these challenges by integrating the current fire alert and deforestation systems and adding improved ecological forecasting of fire risk; expanding data exchange capabilities with mobile technologies; and delivering a deforestation alert product that can inform policies related to land use management and Reduced Emissions from Deforestation and forest Degradation (REDD+). In addition to demonstrating the capabilities of this new real-time alert system, we also highlight how coordination with host-country institutions enhances the system's capacity to address the implementation needs of REDD+ forest carbon projects, improve tropical forest management, strengthen environmental law enforcement, and facilitate the uptake of near real-time satellite monitoring data into business practices of these national/sub-national institutions.

  8. Effects of surface coating on weld growth of resistance spot-welded hot-stamped boron steels

    International Nuclear Information System (INIS)

    Ji, Chang Wook; Lee, Hyun Ju; Kim, Yang Do; Jo, Il Guk; Choi, Il Dong; Park, Yeong Do

    2014-01-01

    Aluminum-silicon-based and zinc-based metallic coatings have been widely used for hot-stamped boron steel in automotive applications. In this study, resistance spot weldability was explored by investigating the effects of the properties of metallic coating layers on heat development and nugget growth during resistance spot welding. In the case of the aluminum-silicon-coated hot-stamped boron steel, the intermetallic coating transformed into a liquid film that covered the faying interface. A wide, weldable current range was obtained with slow heat development because of low contact resistance and large current passage. In the case of the zinc-coated hot-stamped boron steel, a buildup of liquid and vapor formation under large vapor pressure was observed at the faying interface because of the high contact resistance and low vaporization temperature of the intermetallic layers. With rapid heat development, the current passage was narrow because of the limited continuous layer at the faying interface. A more significant change in nugget growth was observed in the zinc coated hot-stamped boron steel than in the aluminum-silicon-coated hot-stamped boron steel.

  9. Micropatterning of a stretchable conductive polymer using inkjet printing and agarose stamping

    DEFF Research Database (Denmark)

    Hansen, Thomas Steen; Hassager, Ole; Larsen, Niels Bent

    2007-01-01

    A highly conducting stretchable polymer material has been patterned using additive inkjet printing and by subtractive agarose stamping of a deactivation agent (hypochlorite). The material consisted of elastomeric polyurethane combined in an interpenetrating network with a conductive polymer, poly(3....... Inkjet printing of the material was only possible if a short-chain polyurethane was used as elastomer to overcome strain hardening at the neck of the droplets produced for printing. Reproducible line widths down to 200 μm could be achieved by inkjet printing. Both methods were used to fabricate test...

  10. Stamps, Stickers and Stigmata. A Social Practice of Antisemitism Presented in a Slide-show

    Directory of Open Access Journals (Sweden)

    Isabel Enzenbach

    2012-07-01

    Full Text Available Antisemitic stickers were disseminated in Germany from the 1880s/1890s onwards. They were glued on letters or postcards, placed visibly in public space or collected in the private sphere. In rethinking antisemitism as a social practice, these stickers, stamps and adhesive labels can be seen as a prototypical source demonstrating the performative dimension of antisemtism. The antisemitic movement used various media such as leaflets, cartoons, speeches, historical novels, articles or newspapers to mobilize people and to build up a community.

  11. Nowcasting and Forecasting the Monthly Food Stamps Data in the US Using Online Search Data

    Science.gov (United States)

    Fantazzini, Dean

    2014-01-01

    We propose the use of Google online search data for nowcasting and forecasting the number of food stamps recipients. We perform a large out-of-sample forecasting exercise with almost 3000 competing models with forecast horizons up to 2 years ahead, and we show that models including Google search data statistically outperform the competing models at all considered horizons. These results hold also with several robustness checks, considering alternative keywords, a falsification test, different out-of-samples, directional accuracy and forecasts at the state-level. PMID:25369315

  12. Estimating Bus Loads and OD Flows Using Location-Stamped Farebox and Wi-Fi Signal Data

    Directory of Open Access Journals (Sweden)

    Yuxiong Ji

    2017-01-01

    Full Text Available Electronic fareboxes integrated with Automatic Vehicle Location (AVL systems can provide location-stamped records to infer passenger boarding at individual stops. However, bus loads and Origin-Destination (OD flows, which are useful for route planning, design, and real-time controls, cannot be derived directly from farebox data. Recently, Wi-Fi sensors have been used to collect passenger OD flow information. But the data are insufficient to capture the variation of passenger demand across bus trips. In this study, we propose a hierarchical Bayesian model to estimate trip-level OD flow matrices and a period-level OD flow matrix using sampled OD flow data collected by Wi-Fi sensors and boarding data provided by fareboxes. Bus loads on each bus trip are derived directly from the estimated trip-level OD flow matrices. The proposed method is evaluated empirically on an operational bus route and the results demonstrate that it provides good and detailed transit route-level passenger demand information by combining farebox and Wi-Fi signal data.

  13. ‘Postage-stamp PIV’: small velocity fields at 400 kHz for turbulence spectra measurements

    Science.gov (United States)

    Beresh, Steven J.; Henfling, John F.; Spillers, Russell W.; Spitzer, Seth M.

    2018-03-01

    Time-resolved particle image velocimetry recently has been demonstrated in high-speed flows using a pulse-burst laser at repetition rates reaching 50 kHz. Turbulent behavior can be measured at still higher frequencies if the field of view is greatly reduced and lower laser pulse energy is accepted. Current technology allows image acquisition at 400 kHz for sequences exceeding 4000 frames but for an array of only 128  ×  120 pixels, giving the moniker of ‘postage-stamp PIV’. The technique has been tested far downstream of a supersonic jet exhausting into a transonic crossflow. Two-component measurements appear valid until 120 kHz, at which point a noise floor emerges whose magnitude is dependent on the reduction of peak locking. Stereoscopic measurement offers three-component data for turbulent kinetic energy spectra, but exhibits a reduced signal bandwidth and higher noise in the out-of-plane component due to the oblique camera images. The resulting spectra reveal two regions exhibiting power-law dependence describing the turbulent decay. The frequency response of the present measurement configuration exceeds nearly all previous velocimetry measurements in high speed flow.

  14. Easily configured real-time CPOE Pick Off Tool supporting focused clinical research and quality improvement.

    Science.gov (United States)

    Rosenbaum, Benjamin P; Silkin, Nikolay; Miller, Randolph A

    2014-01-01

    Real-time alerting systems typically warn providers about abnormal laboratory results or medication interactions. For more complex tasks, institutions create site-wide 'data warehouses' to support quality audits and longitudinal research. Sophisticated systems like i2b2 or Stanford's STRIDE utilize data warehouses to identify cohorts for research and quality monitoring. However, substantial resources are required to install and maintain such systems. For more modest goals, an organization desiring merely to identify patients with 'isolation' orders, or to determine patients' eligibility for clinical trials, may adopt a simpler, limited approach based on processing the output of one clinical system, and not a data warehouse. We describe a limited, order-entry-based, real-time 'pick off' tool, utilizing public domain software (PHP, MySQL). Through a web interface the tool assists users in constructing complex order-related queries and auto-generates corresponding database queries that can be executed at recurring intervals. We describe successful application of the tool for research and quality monitoring.

  15. An Interactive Real-time Decision Support System for Leachate Irrigation on Evapotranspiration Landfill Covers

    Science.gov (United States)

    Wang, Y.

    2015-12-01

    Landfill disposal is still the most common and economical practice for municipal solid waste in most countries. However, heavily polluted leachate generated by excess rainwater percolating through the landfill waste is the major drawback of this practice. Evapotranspiration (ET) cover systems are increasingly being used as alternative cover systems to minimize percolation by evapotranspiration. Leachate recirculation is one of the least expensive options for leachate treatment. The combination of ET cover systems and leachate recirculation can be an economical and environment-friendly practice for landfill leachate management. An interactive real-time decision support system is being developed to better manage leachate irrigation using historical and forecasting weather data, and real time soil moisture data. The main frame of this system includes soil water modules, and plant-soil modules. An inverse simulation module is also included to calibrate certain parameters based on observed data when necessary. It would be an objectives-oriented irrigation management tool to minimize landfill operation costs and negative environmental impacts.

  16. The SARVIEWS Project: Automated SAR Processing in Support of Operational Near Real-time Volcano Monitoring

    Science.gov (United States)

    Meyer, F. J.; Webley, P. W.; Dehn, J.; Arko, S. A.; McAlpin, D. B.; Gong, W.

    2016-12-01

    Volcanic eruptions are among the most significant hazards to human society, capable of triggering natural disasters on regional to global scales. In the last decade, remote sensing has become established in operational volcano monitoring. Centers like the Alaska Volcano Observatory rely heavily on remote sensing data from optical and thermal sensors to provide time-critical hazard information. Despite this high use of remote sensing data, the presence of clouds and a dependence on solar illumination often limit their impact on decision making. Synthetic Aperture Radar (SAR) systems are widely considered superior to optical sensors in operational monitoring situations, due to their weather and illumination independence. Still, the contribution of SAR to operational volcano monitoring has been limited in the past due to high data costs, long processing times, and low temporal sampling rates of most SAR systems. In this study, we introduce the automatic SAR processing system SARVIEWS, whose advanced data analysis and data integration techniques allow, for the first time, a meaningful integration of SAR into operational monitoring systems. We will introduce the SARVIEWS database interface that allows for automatic, rapid, and seamless access to the data holdings of the Alaska Satellite Facility. We will also present a set of processing techniques designed to automatically generate a set of SAR-based hazard products (e.g. change detection maps, interferograms, geocoded images). The techniques take advantage of modern signal processing and radiometric normalization schemes, enabling the combination of data from different geometries. Finally, we will show how SAR-based hazard information is integrated in existing multi-sensor decision support tools to enable joint hazard analysis with data from optical and thermal sensors. We will showcase the SAR processing system using a set of recent natural disasters (both earthquakes and volcanic eruptions) to demonstrate its

  17. Speed of engagement with support generated by a smoking cessation smartphone Just In Time Adaptive Intervention (JITAI

    Directory of Open Access Journals (Sweden)

    Felix Naughton

    2015-10-01

    Full Text Available Background: An advantage of the high portability and sensing capabilities of smartphones is the potential for health apps to deliver advice and support to individuals close in time to when it is deemed of greatest relevance and impact, often referred to as Just In Time Adaptive Interventions (JITAI. However, little research has been undertaken to explore the viability of JITAI in terms of how long it takes users to engage with support triggered by real time data input, compared to scheduled support, and whether context affects response. This paper is focused on Q Sense, a smoking cessation app developed to deliver both Just in Time and scheduled support messages (every morning during a smoker’s quit attempt. The Just in Time cessation support generated by Q Sense is triggered by and tailored to real time context using location sensing. Objectives: To assess: 1 the time to engage with the app after a Just in Time support notification is delivered and whether this is influenced by the context in which the notification was initially delivered, 2 whether the time to engage with the app differs between Just in Time support notifications and scheduled support message notifications and 3 whether findings from objectives 1 and 2 differ between smokers receiving or not receiving NHS smoking cessation support. Methods: Data are from two studies evaluating the use of Q Sense: a feasibility study using an opportunity sample of smokers initiating a quit attempt with Q Sense without NHS cessation support (N=15 and an ongoing acceptability study of smokers receiving NHS smoking cessation support alongside app use (target N=40, recruitment due to be completed end of November 2015. Time elapse between notification generation and the user opening the app will be calculated and compared between message types (Just in Time vs. scheduled messages, contexts (home, work, socialising, other and samples (receiving or not receiving NHS cessation support using t

  18. A global health partnership's use of time-limited support to catalyze health practice change: the case of GAVI's Injection Safety Support.

    Science.gov (United States)

    Levin, Ann; Fang, Arnold; Hansen, Peter M; Pyle, David; Dia, Ousmane; Schwalbe, Nina

    2010-09-27

    This paper presents the findings of a study to assess the effectiveness and sustainability of a GAVI (Global Alliance of Vaccines and Immunization) sponsored, time-limited Injection Safety (INS) support. The support came in two forms: 1) in-kind, in the form of AD syringes and safety boxes, and 2) in cash, for those countries that already had a secure, multi-year source of AD syringes and safety boxes, but proposed to use INS support to strengthen their injection safety activities. In total, GAVI gave INS support for a three-year period to 58 countries: 46 with commodities and 12 with cash support. To identify variables that might be associated with financial sustainability, frequencies and cross-tabulations were run against various programmatic and socio-economic variables in the 58 countries. All but two of the 46 commodity-recipient countries were able to replace and sustain the use of AD syringes and safety boxes after the end of their GAVI INS support despite the fact that standard disposable syringes are less costly than ADs (10-15 percent differential). In addition, all 12 cash-recipient countries continued to use AD syringes and safety boxes in their immunization programs in the years following GAVI INS assistance. At the same time, countries were often not prepared for the increased waste management requirements associated with the use of the syringes, suggesting the importance of anticipating challenges with the introduction of new technologies. The sustained use of AD syringes in countries receiving injection safety support from GAVI, in a majority of cases through government financing, following the completion of three years of time-limited support, represents an early indication of how GHPs can contribute to improved health outcomes in immunization safety in the world's poorest countries in a sustainable way.

  19. A global health partnership's use of time-limited support to catalyze health practice change: the case of GAVI's Injection Safety Support.

    Directory of Open Access Journals (Sweden)

    Ann Levin

    Full Text Available This paper presents the findings of a study to assess the effectiveness and sustainability of a GAVI (Global Alliance of Vaccines and Immunization sponsored, time-limited Injection Safety (INS support. The support came in two forms: 1 in-kind, in the form of AD syringes and safety boxes, and 2 in cash, for those countries that already had a secure, multi-year source of AD syringes and safety boxes, but proposed to use INS support to strengthen their injection safety activities. In total, GAVI gave INS support for a three-year period to 58 countries: 46 with commodities and 12 with cash support. To identify variables that might be associated with financial sustainability, frequencies and cross-tabulations were run against various programmatic and socio-economic variables in the 58 countries. All but two of the 46 commodity-recipient countries were able to replace and sustain the use of AD syringes and safety boxes after the end of their GAVI INS support despite the fact that standard disposable syringes are less costly than ADs (10-15 percent differential. In addition, all 12 cash-recipient countries continued to use AD syringes and safety boxes in their immunization programs in the years following GAVI INS assistance. At the same time, countries were often not prepared for the increased waste management requirements associated with the use of the syringes, suggesting the importance of anticipating challenges with the introduction of new technologies. The sustained use of AD syringes in countries receiving injection safety support from GAVI, in a majority of cases through government financing, following the completion of three years of time-limited support, represents an early indication of how GHPs can contribute to improved health outcomes in immunization safety in the world's poorest countries in a sustainable way.

  20. The collection of Tuvan stamps (1926–1943 in the National Museum of the Republic of Tuva and the prospects of philately in Tuva

    Directory of Open Access Journals (Sweden)

    Kaadyr-ool A. Bicheldey

    2016-09-01

    Full Text Available Stamps of the People’s Republic of Tuva (PRT, 1921-1944 as indicia and as items of collectors’ interest, are universally renowned, and as such have been the subject of a good deal of research. These works contain more than a mere story of Tuvan stamps – they provide a lot of useful information on Tuva, its history, including the history of postal service in the region. This article describes the collection of indicia (more than 500 pieces dated 1926-1943 and preserved at Aldan Maadyr National Museum of Tuva. On the basis of this analysis we have formulated the current problems and prospects of philately in the region. The stamp collection in the National Museum fills 4 albums of various sizes and a number of envelopes with 1-72 stamps in each. The compilers of 2 albums attempted to systematize stamps by issue date, but this work is far from complete. There is no definitive collection of Tuvan stamps to act as a model for others, regardless of the quality of the stamps preserved. The rest of the stamps in the museum collection is in unsorted state. Overall, the degree of preservation can be tentatively described as average. Given the great interest of scholars and collectors, Tuvan stamps are relatively little studies. The overall bulk of material on the uses of stamps in Tuva lacks an overarching study. We have summed up the main research problems that call for in-depth research, including studying Tuvan stamps as pieces of art, the financial and economic viability of issuing stamps in PRT, the official documentations licensing the issue, full catalogization of all existing issues, the study of individual stamps, etc. Especially urgent is the issue of propagating knowledge of history of Tuvan postal service as a precondition for collecting and preserving PRT stamps. Archives of many Tuvan families may contain unique stamps, rare envelopes or postcards – but few of their owners recognize the full value of what they have. This puts unique

  1. Experimental Investigation About Stamping Behaviour of 3D Warp Interlock Composite Preforms

    Science.gov (United States)

    Dufour, Clément; Wang, Peng; Boussu, François; Soulat, Damien

    2014-10-01

    Forming of continuous fibre reinforcements and thermoplastic resin commingled prepregs can be performed at room temperature due to its similar textile structure. The "cool" forming stage is better controlled and more economical. The increase of temperature and the resin consolidation phases after the forming can be carried out under the isothermal condition thanks to a closed system. It can avoid the manufacturing defects easily experienced in the non-isothermal thermoforming, in particular the wrinkling [1]. Glass/Polypropylene commingled yarns have been woven inside different three-dimensional (3D) warp interlock fabrics and then formed using a double-curved shape stamping tool. The present study investigates the in-plane and through-thickness behaviour of the 3D warp interlock fibrous reinforcements during forming with a hemispherical punch. Experimental data allow analysing the forming behaviour in the warp and weft directions and on the influence of warp interlock architectures. The results point out that the layer to layer warp interlock preform has a better stamping behaviour, in particular no forming defects and good homogeneity in thickness.

  2. Defect detection and classification of galvanized stamping parts based on fully convolution neural network

    Science.gov (United States)

    Xiao, Zhitao; Leng, Yanyi; Geng, Lei; Xi, Jiangtao

    2018-04-01

    In this paper, a new convolution neural network method is proposed for the inspection and classification of galvanized stamping parts. Firstly, all workpieces are divided into normal and defective by image processing, and then the defective workpieces extracted from the region of interest (ROI) area are input to the trained fully convolutional networks (FCN). The network utilizes an end-to-end and pixel-to-pixel training convolution network that is currently the most advanced technology in semantic segmentation, predicts result of each pixel. Secondly, we mark the different pixel values of the workpiece, defect and background for the training image, and use the pixel value and the number of pixels to realize the recognition of the defects of the output picture. Finally, the defect area's threshold depended on the needs of the project is set to achieve the specific classification of the workpiece. The experiment results show that the proposed method can successfully achieve defect detection and classification of galvanized stamping parts under ordinary camera and illumination conditions, and its accuracy can reach 99.6%. Moreover, it overcomes the problem of complex image preprocessing and difficult feature extraction and performs better adaptability.

  3. Data and Geocomputation: Time Critical Mission Support for the 2017 Hurricane Season

    Science.gov (United States)

    Bhaduri, B. L.; Tuttle, M.; Rose, A.; Sanyal, J.; Thakur, G.; White, D.; Yang, H. H.; Laverdiere, M.; Whitehead, M.; Taylor, H.; Jacob, M.

    2017-12-01

    A strong spatial data infrastructure and geospatial analysis capabilities are nucleus to the decision-making process during emergency preparedness, response, and recovery operations. For over a decade, the U.S. Department of Energy's Oak Ridge National Laboratory has been developing critical data and analytical capabilities that provide the Federal Emergency Management Agency (FEMA) and the rest of the federal response community assess and evaluate impacts of natural hazards on population and critical infrastructures including the status of the national electricity and oil and natural gas networks. These capabilities range from identifying structures or buildings from very high-resolution satellite imagery, utilizing machine learning and high-performance computing, to daily assessment of electricity restoration highlighting changes in nighttime lights for the impacted region based on the analysis of NOAA JPSS VIIRS Day/Night Band (DNB) imagery. This presentation will highlight our time critical mission support efforts for the 2017 hurricane season that witnessed unprecedented devastation from hurricanes Harvey, Irma, and Maria. ORNL provided 90m resolution LandScan USA population distribution data for identifying vulnerable population as well as structure (buildings) data extracted from 1m imagery for damage assessment. Spatially accurate data for solid waste facilities were developed and delivered to the response community. Human activity signatures were assessed from large scale collection of open source social media data around points of interests (POI) to ascertain level of destruction. The electricity transmission system was monitored in real time from data integration from hundreds of utilities and electricity outage information were provided back to the response community via standardized web-services.

  4. Wireless just-in-time training of mobile skilled support personnel

    Science.gov (United States)

    Bandera, Cesar; Marsico, Michael; Rosen, Mitchel; Schlegel, Barry

    2006-05-01

    Skilled Support Personnel (SSP) serve emergency response organizations during an emergency incident, and include laborers, operating engineers, carpenters, ironworkers, sanitation workers and utility workers. SSP called to an emergency incident rarely have recent detailed training on the chemical, biological, radiological, nuclear and/or explosives (CBRNE) agents or the personal protection equipment (PPE) relevant to the incident. This increases personal risk to the SSP and mission risk at the incident site. Training for SSP has been identified as a critical need by the National Institute for Environmental Health Sciences, Worker Education and Training Program. We present a system being developed to address this SSP training shortfall by exploiting a new training paradigm called just-in-time training (JITT) made possible by advances in distance learning and cellular telephony. In addition to the current conventional training at regularly scheduled instructional events, SSP called to an emergency incident will have secure access to short (technologies and wireless service providers, integration with the incident management system, and SCORM compliance.

  5. Evaluation of real-time clinical decision support systems for platelet and cryoprecipitate orders.

    Science.gov (United States)

    Collins, Ryan A; Triulzi, Darrell J; Waters, Jonathan H; Reddy, Vivek; Yazer, Mark H

    2014-01-01

    To evaluate cryoprecipitate and platelet ordering practices after the implementation of real-time clinical decision support systems (CDSSs) in a computerized physician order entry (CPOE) system. Uniform platelet and cryoprecipitate transfusion thresholds were implemented at 11 hospitals in a regional health care system with a common CPOE system. Over 6 months, a variety of information was collected on the ordering physicians and the number of alerts generated by the CDSSs when these products were ordered outside of the institutional guidelines. There were 1,889 orders for platelets and 152 orders for cryoprecipitate placed in 6 months. Of these, 1,102 (58.3%) platelet and 74 (48.7%) cryoprecipitate orders triggered an alert. The proportion of orders canceled after an alert was generated ranged from 13.5% to 17.9% for platelets and 0% to 50.0% for cryoprecipitate orders. CDSS alerts reduce, but do not eliminate, platelet and cryoprecipitate transfusions that do not meet institutional guidelines.

  6. The software architecture of the real-time on-line decision support system 'RODOS'

    International Nuclear Information System (INIS)

    Rafat, M.; Schuele, O.

    1998-01-01

    The RODOS project aims at the development of an integrated and comprehensive real-time on-line decision support system for off-site emergency management of nuclear accidents in Europe, applicable for the vicinity of the release and the early phase up to far distant areas and the later stages of an accident. The architecture of the RODOS software framework is described as a tool for processing and managing a large variety of different types of information, including those which are categorized in terms of meteorology, radiology, economy, emergency actions and countermeasures, rules, preferences, facts, maps, statistics, catalogues, models and methods. The conceptual design of the software structure based on the Client-Server model and the practical co-operation between a set of autonomous applications meeting the user requirements and objectives are discussed. Details of co-operation management are described by explaining the concepts of the inter-module communication, data exchange, control of operation and data model. (author)

  7. Enabling Real-time Water Decision Support Services Using Model as a Service

    Science.gov (United States)

    Zhao, T.; Minsker, B. S.; Lee, J. S.; Salas, F. R.; Maidment, D. R.; David, C. H.

    2014-12-01

    Through application of computational methods and an integrated information system, data and river modeling services can help researchers and decision makers more rapidly understand river conditions under alternative scenarios. To enable this capability, workflows (i.e., analysis and model steps) are created and published as Web services delivered through an internet browser, including model inputs, a published workflow service, and visualized outputs. The RAPID model, which is a river routing model developed at University of Texas Austin for parallel computation of river discharge, has been implemented as a workflow and published as a Web application. This allows non-technical users to remotely execute the model and visualize results as a service through a simple Web interface. The model service and Web application has been prototyped in the San Antonio and Guadalupe River Basin in Texas, with input from university and agency partners. In the future, optimization model workflows will be developed to link with the RAPID model workflow to provide real-time water allocation decision support services.

  8. Effectiveness of different approaches to disseminating traveler information on travel time reliability. [supporting datasets

    Science.gov (United States)

    2013-11-30

    Travel time reliability information includes static data about traffic speeds or trip times that capture historic variations from day to day, and it can help individuals understand the level of variation in traffic. Unlike real-time travel time infor...

  9. Social Support May Buffer the Effect of Intrafamilial Stressors on Preschool Children's Television Viewing Time in Low-Income Families

    Science.gov (United States)

    Jurkowski, Janine M.; Davison, Kirsten K.

    2013-01-01

    Abstract Background: Excessive television (TV) viewing in preschool children has been linked to negative outcomes during childhood, including childhood obesity. In a sample of low-income families, this study examined associations between intrafamilial factors and preschool children's TV-viewing time and the moderating effect of social support from nonfamily members on this association. Methods: In 2010, 129 mothers/female guardians of 2- to 5-year-old children enrolled at five Head Start centers in Rensselaer County, New York, completed a self-report survey. The survey assessed child TV-viewing time (including TV, DVDs, and videos) and intrafamilial risk factors, including maternal perceived stress, depressive symptoms, TV viewing, leisure-time physical activity (inactivity), and family functioning. Social support from nonfamily members (nonfamily social support) was also measured and examined as an effect modifier. Results: Children watched TV an average of 160 minutes per day. Moderate depressive symptoms (Personal Health Questionnaire depression scale scores ≥10), higher perceived stress, poorer family functioning, and higher maternal TV-viewing were significantly and independently associated with greater minutes of child TV viewing, controlling for covariates. In all instances, nonfamily social support moderated these associations, such that negative experiences within the family environment were linked with higher child TV-viewing time under conditions of low nonfamily social support, but not high nonfamily support. Conclusions: Social support from nonfamily members may buffer potentially negative effects of intrafamilial factors on preschool children's TV-viewing time. PMID:24168754

  10. Social support may buffer the effect of intrafamilial stressors on preschool children's television viewing time in low-income families.

    Science.gov (United States)

    Li, Kaigang; Jurkowski, Janine M; Davison, Kirsten K

    2013-12-01

    Excessive television (TV) viewing in preschool children has been linked to negative outcomes during childhood, including childhood obesity. In a sample of low-income families, this study examined associations between intrafamilial factors and preschool children's TV-viewing time and the moderating effect of social support from nonfamily members on this association. In 2010, 129 mothers/female guardians of 2- to 5-year-old children enrolled at five Head Start centers in Rensselaer County, New York, completed a self-report survey. The survey assessed child TV-viewing time (including TV, DVDs, and videos) and intrafamilial risk factors, including maternal perceived stress, depressive symptoms, TV viewing, leisure-time physical activity (inactivity), and family functioning. Social support from nonfamily members (nonfamily social support) was also measured and examined as an effect modifier. Children watched TV an average of 160 minutes per day. Moderate depressive symptoms (Personal Health Questionnaire depression scale scores ≥10), higher perceived stress, poorer family functioning, and higher maternal TV-viewing were significantly and independently associated with greater minutes of child TV viewing, controlling for covariates. In all instances, nonfamily social support moderated these associations, such that negative experiences within the family environment were linked with higher child TV-viewing time under conditions of low nonfamily social support, but not high nonfamily support. Social support from nonfamily members may buffer potentially negative effects of intrafamilial factors on preschool children's TV-viewing time.

  11. Can laboratory and pilot recycling trials predict adhesive removal in commercial recycling systems? : results from the USPS environmentally benign stamp project

    Science.gov (United States)

    Carl Houtman; Daniel Seiter; Nancy Ross Sutherland; Donald Donermeyer

    2002-01-01

    The ultimate goal of the US Postal Service (USPS) Environmentally Benign Stamp Program is to develop stamp laminates, i.e., face paper, adhesive and siliconized liner, that do not cause difficulties in recycling mills. The criterion for success, and the USPS definition of benignity, is the avoidance of process and product quality hardships when such PSA laminates are...

  12. Fabrication of a metallic roll stamp with low internal stress and high hardness for large area display applications by a pulse reverse current electroforming process

    International Nuclear Information System (INIS)

    Kim, Joongeok; Han, Jungjin; Kim, Taekyung; Kang, Shinill

    2014-01-01

    With the increasing demand for large scale micro/nano components in the fields of display, energy and electrical devices, etc, the establishment of a roll imprinting process has become a priority. The fabrication of a roll stamp with high dimensional accuracy and uniformity is one of the key issues in the roll imprinting process, because the roll stamp determines the properties of the replicated micro/nano structures. In this study, a method to fabricate a metallic roll stamp with low internal stress, high flatness, and high hardness was proposed by a pulse reverse current (PRC) electroforming process. The effects of PRC electroforming processes on the internal stress, hardness, and grain size of the electroformed stamp were examined, and the optimum process conditions were suggested. As a practical example of the proposed method, various micro-patterns for electronic circuits were fabricated via the roll imprinting process using a PRC electroformed stamp. (paper)

  13. Ocean observing systems support operational forecasts for the timing of Maine's lobster fishery

    Science.gov (United States)

    Mills, K.; Hernandez, C.; Pershing, A. J.

    2016-02-01

    American lobster supports one of the most valuable fisheries in the United States, with a landed value in 2013 exceeding $460M. Although US lobstermen are free to fish throughout the year, the New England climate, lobster biology and fleet dynamics lead to a strong annual cycle with catch rates rising rapidly in early summer and landings peaking in late summer. When this annual cycle is disrupted, it can impact the supply and ultimately the price of lobsters. During the record warm conditions in 2012, the rise in catch rates occurred three weeks ahead of normal. Combined with higher than normal landings from the spring Canadian fishery, the early and high volume landings in 2012 led to a collapse in price that severely stressed the U. S. fishery, especially in Maine where over 85% of the landings occur. Based on this experience, we have been developing seasonal forecasts of the phenology of Maine lobster landings. Using temperatures at 50m from four NERACOOS buoys in the Gulf of Maine, we can reliably forecast the date when the Maine lobster fishery will `turn on' for the year, with prediction accuracy peaking in April. The high-landings period normally starts in July, and the 2-3 month lead-time provides some advance warning to dealers and processors of when their capacity needs to be ready and to fishermen of potential supply chain and market impacts such as we observed in 2012. We are currently working towards finer-scale regional forecasts along the Maine coast that may include other features that will provide information to help the lobster industry adapt to the rapid changes that are underway in the Gulf of Maine.

  14. A mobile application to support collection and analytics of real-time critical care data.

    Science.gov (United States)

    Vankipuram, Akshay; Vankipuram, Mithra; Ghaemmaghami, Vafa; Patel, Vimla L

    2017-11-01

    Data collection, in high intensity environments, poses several challenges including the ability to observe multiple streams of information. These problems are especially evident in critical care, where monitoring of the Advanced Trauma Life Support (ATLS) protocol provides an excellent opportunity to study the efficacy of applications that allow for the rapid capture of event information, providing theoretically-driven feedback using the data. Our goal was, (a) to design and implement a way to capture data on deviation from the standard practice based on the theoretical foundation of error classification from our past research, (b) to provide a means to meaningfully visualize the collected data, and (c) to provide a proof-of-concept for this implementation, using some understanding of user experience in clinical practice. We present the design and development of a web application designed to be used primarily on mobile devices and a summary data viewer to allow clinicians to, (a) track their activities, (b) provide real-time feedback of deviations from guidelines and protocols, and (c) provide summary feedback highlighting decisions made. We used a framework previously developed to classify activities in trauma as the theoretical foundation of the rules designed to do the same algorithmically, in our application. Attending physicians at a Level 1 trauma center used the application in the clinical setting and provided feedback for iterative development. Informal interviews and surveys were used to gain some deeper understanding of the user experience using this application in-situ. Activity visualizations were created highlighting decisions made during a trauma code as well as classification of tasks per the theoretical framework. The attendings reviewed the efficacy of the data visualizations as part of their interviews. We also conducted a proof-of-concept evaluation by way of usability questionnaire. Two attendings rated 4 out of the usability 6 categories highly

  15. Changes in Social Support over Time in a Faith-Based Physical Activity Intervention

    Science.gov (United States)

    Story, Chandra R.; Knutson, Douglas; Brown, Jameisha B.; Spears-Laniox, Erica; Harvey, Idethia Shevon; Gizlice, Ziya; Whitt-Glover, Melicia C.

    2017-01-01

    African-American women report higher levels of chronic conditions and church attendance relative to the overall US population. Therefore, efforts have increased over the past decade to design church-based health promotion programs. The present study compared changes in religiosity, religious social support and general social support across time…

  16. Enhancement of Near-Real-Time Cloud Analysis and Related Analytic Support for Whole Sky Imagers

    National Research Council Canada - National Science Library

    Shields, Janet E; Karr, Monette E; Burden, Art R; Johnson, Richard W; Hodgkiss, William S

    2007-01-01

    ... DO #4, between 25 May 01 and 31 September 06. This work relates to the Air Force s need to characterize the cloud distribution during day and night, for a variety of applications, including support of satellite tracking, and support of research...

  17. Separation and Divorce: Supporting Children and Families in Times of Stress.

    Science.gov (United States)

    Gray, Barbara

    2001-01-01

    Discusses how teachers/caregivers can support children and families during marital separation and divorce. Describes the impact of divorce on young children. Offers eight suggestions for teachers/caregivers, including providing security and support, helping children feel competent and in control, understanding why children may have behavior…

  18. FUEL SERVICES: Customer focused on Product Support during the whole Life Time

    Energy Technology Data Exchange (ETDEWEB)

    Langenberger, J.; Hummel, W.

    2015-07-01

    For more than 40 years, Fuel Services of AREVA has been delivering devices and providing on-site services primary at LWR worldwide. We support our worldwide customers in achieving safe and economic operation of the fuel assemblies (FA) and core components (CC) and have received excellent feedback from them. But the Fuel Services support goes beyond on-site activities. (Author)

  19. Ben Franklin, America’s Postage Stamp Star — on the Wane?

    Directory of Open Access Journals (Sweden)

    François Brunet

    2010-01-01

    Full Text Available This paper is an assessment of Ben Franklin’s evolving figure in U.S. postage stamps, focusing especially on the contrast between the 2006 tercentennial Franklin 4-stamp panel, a rather high-brow representation of Franklin as an intellectual, and his traditional image as a homely, common face. The singular history of U.S. postage stamps, with their innovative choice of historical figures as subject matter and their broader emphasis on commemoration, is briefly summarized. The evolution of the Franklin figure — the most common postal image, along with George Washington — is then detailed, showing how the traditional image prevailed until the 1950s, before being progressively displaced by a more cultural and, lately, intellectual image of the nation’s “electrizer”.Cet article vise à interpréter l’évolution de la figure de Benjamin Franklin dans les timbres-poste des Etats-Unis, en se fondant notamment sur le contraste entre le bloc de quatre timbres émis lors du tricentenaire en 2006, qui représente Franklin dans les différents métiers d’un intellectuel des Lumières, et son image traditionnelle d’Américain simple et moyen. On retrace tout d’abord l’histoire singulière des timbres américains, caractérisée par le choix innovant de figures historiques comme sujets et plus généralement par la prééminence de la fonction commémorative. Puis on étudie en détail l’évolution de la figure de Franklin — sujet le plus fréquent des timbres américains avec George Washington — en montrant que l’image traditionnelle s’est perpétuée jusqu’aux années 1950, avant de céder progressivement à une image plus culturelle et, récemment, plus intellectuelle.

  20. Autonomy promotion, responsiveness, and emotion regulation promote effective social support in times of stress.

    Science.gov (United States)

    Cutrona, Carolyn E; Russell, Daniel W

    2017-02-01

    Adult attachment theory provides guidance for providing optimal social support in intimate relationships. According to attachment theory, facilitating autonomy (secure base support) sometimes is more important than providing nurturance (safe haven support). In addition, it is important that couples celebrate one another's triumphs and successes (another form of secure base support). A key construct that explains the development of attachment is responsiveness to the individual's needs. Support that is delivered in a responsive manner (i.e., that leads the individual to feel understood, validated, and cared for) is more likely to enhance the relationship and less likely to damage self-esteem than assistance that is not responsive. A responsive exchange is more likely if emotion dysregulation can be prevented. Attachment theory offers explanations for why people vary in their effectiveness at emotion regulation. Appropriate emotion regulation is more likely if disclosures of current difficulties can be made in a way that is not defensive or accusatory, an ability that varies as a function of attachment orientation. Attachment theory also offers guidance regarding the optimal forms of social support for specific individuals. All these insights from adult attachment theory can be integrated into interventions to help couples become more effective support providers. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Doctoral Students’ Social Support Profiles and Their Relationship to Burnout, Drop-Out Intentions, and Time to Candidacy

    Directory of Open Access Journals (Sweden)

    Jouni A Peltonen

    2017-08-01

    Full Text Available Aim/Purpose: The primary aim of this study was to better understand the individual variations in supervisory and researcher community support among doctoral students by analyzing the social support profiles of Finnish doctoral students. The differences among the profiles, in terms of satisfaction with supervision, experienced burnout, time to candidacy and disciplinary background were also examined. Background: This study explores social support profiles and their association with the experienced burnout, satisfaction with supervision, drop-out intentions, disciplinary background, and form of dissertation among doctoral students by employing a person-oriented approach. Methodology: In total, 402 doctoral students from a Finnish university completed a Doctoral Experience survey. Latent Profile Analysis (LPA was used to group doctoral students according to social support from supervisors and the researcher community. Contribution: The present study is among the first quantitative studies to explore doctoral student social support profiles and their association with burnout, drop-out intentions, and time to candidacy. It brings into focus the importance of supervisory and researcher community support as one of the most crucial assets of doctoral education in researcher communities. Findings: Two social support profiles, a sufficient support from supervisor and researched community, and b insufficient support from both of these, were identified. Further investigation suggested that the doctoral students who received sufficient support were less likely to suffer from burnout and were less likely to develop drop-out intentions than students who received insufficient support from their supervisor and the researcher community. Recommendations for Practitioners: A recommendation deriving from this research is to identify students at risk as early as possible and assist them with sufficient support.

  2. Preschool Teachers' Financial Well-Being and Work Time Supports: Associations with Children's Emotional Expressions and Behaviors in Classrooms

    Science.gov (United States)

    King, Elizabeth K.; Johnson, Amy V.; Cassidy, Deborah J.; Wang, Yudan C.; Lower, Joanna K.; Kintner-Duffy, Victoria L.

    2016-01-01

    The current study examined associations among teachers' financial well-being, including teachers' wages and their perceptions of their ability to pay for basic expenses, and teachers' work time supports, including teachers' paid planning time, vacation days, and sick days, and children's positive emotional expressions and behaviors in preschool…

  3. Banking Time in Head Start: Early Efficacy of an Intervention Designed to Promote Supportive Teacher-Child Relationships

    Science.gov (United States)

    Driscoll, Katherine C.; Pianta, Robert C.

    2010-01-01

    Research Findings: This exploratory study encompassed a collaboration to implement and evaluate the early efficacy of Banking Time, a dyadic intervention designed to promote supportive teacher-child relationships. Banking Time is a set of one-on-one meetings between a teacher and a child consisting of child-led play and teacher facilitation…

  4. Micromechanics-based modeling of stress–strain and fracture behavior of heat-treated boron steels for hot stamping process

    Energy Technology Data Exchange (ETDEWEB)

    Srithananan, P.; Kaewtatip, P.; Uthaisangsuk, V., E-mail: vitoon.uth@kmutt.ac.th

    2016-06-14

    In the automotive industry, hot stamped parts with tailored properties have shown advantageous safety performance. Such components are produced by applying different heat treatment conditions after forming for different zones in order to obtain various combinations of hard and soft microstructures. In this work, pure martensitic, pure bainitic, and three martensitic/bainitic phase microstructures were initially generated from the boron steel grade 22MnB5 by a two-step quenching procedure in which different holding times in the bainitic temperature range were varied. Increased phase fraction of bainite due to longer holding time led to decreased yield and tensile strength; however, elongation and resulting energy absorbability became significantly higher. To describe mechanical properties and failure behavior of hot stamped parts containing multiphase microstructures, influences of microstructure characteristics should be considered on the micro-scale. Using modeling, 2-D representative volume elements (RVE) were generated from observed real microstructures and flow curves of the individual single phases were defined, taking into account a dislocation theory based model and local chemical compositions. Then, effective stress–strain curves of the heat-treated boron steels were calculated by using the isostrain and non-isostrain methods and compared with tensile test results. Regarding fracture behavior, damage curves of fully martensitic and bainitic structures were determined by means of tensile tests of different notched samples and a hybrid digital image correlation (DIC)–finite element (FE) approach. 2-D RVE simulations of a martensite/bainite mixture were carried out under various states of stress, in which the obtained damage curves were individually applied for each phase. The predicted damage curve from RVE simulations for two-phase boron steel fairly agreed with experimental fracture strains. Moreover, correspondingly normalized Lode angle could be

  5. Modeling and simulation of stamp deflections in nanoimprint lithography: Exploiting backside grooves to enhance residual layer thickness uniformity

    DEFF Research Database (Denmark)

    Taylor, Hayden; Smistrup, Kristian; Boning, Duane

    2011-01-01

    We describe a model for the compliance of a nanoimprint stamp etched with a grid of backside grooves. We integrate the model with a fast simulation technique that we have previously demonstrated, to show how etched grooves help reduce the systematic residual layer thickness (RLT) variations...

  6. Investigation of Hardness Change for Spot Welded Tailored Blank in Hot Stamping Using CCT and Deformation-CCT Diagrams

    Science.gov (United States)

    Yogo, Yasuhiro; Kurato, Nozomi; Iwata, Noritoshi

    2018-04-01

    When an outer panel of a B-pillar is manufactured with the hot stamping process, reinforcements are spot welded on its inner side. Before reinforcements are added, the microstructure of the outer panel is martensite. However, reheating during spot welding changes the martensite to ferrite, which has a lower hardness in the heat-affected zone than in other areas. If spot welding is conducted before hot stamping for making a spot welded tailored blank, the microstructure in the spot welded tailored blank after hot stamping is martensite. This sequence of processes avoids hardness reduction due to spot welding. In this study, the hardness and microstructure around spot welded parts of the tailored blank were investigated. The results clearly showed that areas close to the spot welded parts are severely stretched during hot stamping. In addition, stretching suppresses the martensitic phase transformation and reduces the hardness. To characterize this phenomenon, a simulation was conducted that considered the effects of pre-strain on the phase transformation. A continuous cooling transformation (CCT) diagram and a deformation continuous cooling transformation (DCCT) diagram were made in order to quantify the effect of the cooling rate and pre-strain on the phase transformation and hardness. The hardness was then calculated using the experimentally measured CCT and DCCT diagrams and the finite element analysis results. The calculated hardness was compared with the experimental hardness. Good agreement was found between the calculated and experimental results.

  7. The new Swiss commemorative stamp dedicated to CERN available at the Organization's Meyrin post office on Tuesday, 9 March!

    CERN Multimedia

    Maximilien Brice

    2004-01-01

    For some people, the stamp's rays are spreading outwards towards the infinitely large, while for others they focus inwards towards the infinitely small. It's a bit like the proverbial half-full or half-empty glass or a picture that conveys two different images, depending on how you look at it.

  8. Microstructure and Properties of a New Cr - Mn Steel without Boron Additions for Use in Hot Stamping

    Science.gov (United States)

    Zhou, H.; Zhu, G.; Li, Q.; Chen, Q.

    2015-09-01

    Anew hot-stamping steel that is alloyed with chromium and manganese and does not contain boron additions has been developed. The effect of reheating temperature and cooling rates on the mechanical properties and structure of the steel is determined. Atreatment regime that increases the ductility of the steel without a noticeable decrease in its strength is proposed.

  9. Investigation of Hardness Change for Spot Welded Tailored Blank in Hot Stamping Using CCT and Deformation-CCT Diagrams

    Science.gov (United States)

    Yogo, Yasuhiro; Kurato, Nozomi; Iwata, Noritoshi

    2018-06-01

    When an outer panel of a B-pillar is manufactured with the hot stamping process, reinforcements are spot welded on its inner side. Before reinforcements are added, the microstructure of the outer panel is martensite. However, reheating during spot welding changes the martensite to ferrite, which has a lower hardness in the heat-affected zone than in other areas. If spot welding is conducted before hot stamping for making a spot welded tailored blank, the microstructure in the spot welded tailored blank after hot stamping is martensite. This sequence of processes avoids hardness reduction due to spot welding. In this study, the hardness and microstructure around spot welded parts of the tailored blank were investigated. The results clearly showed that areas close to the spot welded parts are severely stretched during hot stamping. In addition, stretching suppresses the martensitic phase transformation and reduces the hardness. To characterize this phenomenon, a simulation was conducted that considered the effects of pre-strain on the phase transformation. A continuous cooling transformation (CCT) diagram and a deformation continuous cooling transformation (DCCT) diagram were made in order to quantify the effect of the cooling rate and pre-strain on the phase transformation and hardness. The hardness was then calculated using the experimentally measured CCT and DCCT diagrams and the finite element analysis results. The calculated hardness was compared with the experimental hardness. Good agreement was found between the calculated and experimental results.

  10. Social support and leisure-time physical activity: longitudinal evidence from the Brazilian Pró-Saúde cohort study

    Directory of Open Access Journals (Sweden)

    Werneck Guilherme L

    2011-07-01

    Full Text Available Abstract Background Although social support has been observed to exert a beneficial influence on leisure-time physical activity (LTPA, multidimensional approaches examining social support and prospective evidence of its importance are scarce. The purpose of this study was to investigate how four dimensions of social support affect LTPA engagement, maintenance, type, and time spent by adults during a two-year follow-up. Methods This paper reports on a longitudinal study of 3,253 non-faculty public employees at a university in Rio de Janeiro (the Pró-Saúde study. LTPA was evaluated using a dichotomous question with a two-week reference period, and further questions concerning LTPA type (individual or group and time spent on the activity. Social support was measured by the Medical Outcomes Study Social Support Scale (MOS-SSS. To assess the association between social support and LTPA, two different statistical models were used: binary and multinomial logistic regression models for dichotomous and polytomous outcomes, respectively. Models were adjusted separately for those who began LTPA in the middle of the follow up (engagement group and for those who had maintained LTPA since the beginning of the follow up (maintenance group. Results After adjusting for confounders, statistically significant associations (p Conclusions All dimensions of social support influenced LTPA type or the time spent on the activity. However, our findings suggest that social support is more important in engagement than in maintenance. This finding is important, because it suggests that maintenance of LTPA must be associated with other factors beyond the individual's level of social support, such as a suitable environment and social/health policies directed towards the practice of LTPA.

  11. In Dogs With a European Adder Bite, Does the Use of Antivenom With Supportive Treatment Compared to Supportive Treatment Alone Improve Time to Recovery?

    Directory of Open Access Journals (Sweden)

    Lindsay Hodgson

    2017-11-01

    Full Text Available The current literature does not offer convincing evidence for the positive effect of antivenom on time to recovery in dogs envenomated by the European adder. It appears that the use of antivenom in addition to supportive treatment may positively affect local swelling if given within 24 hours of the bite, but the evidence is low quality and further studies are required before a more definitive answer can be reached.

  12. Determination of stamp deformation during imprinting on semi-spherical surfaces

    DEFF Research Database (Denmark)

    Kafka, Jan; Matschuk, Maria; Pranov, Henrik

    of sol-gel was applied onto spherical injection mold inserts and subsequently imprinted using a flexible stamp. A hard curing step transformed the sol-gel into a quartz-like and durable material. As an example, we present theory and results regarding the imprint of pillar nanostructures on semi......-spherical mold surfaces. Imprints were realized on three different radii of circumferenceof the spherical mold: R = 0.5 mm, R = 1.0 mm, and R = 2 mm. After hard-curing of theimprinted sol-gel, the inserts were used for cold-mold as well as vario-therm injection molding.The polymer replicas and the inserts were...

  13. SOCIAL RESPONSIBILITY SCORE: COMPARATIVE STUDY BETWEEN PUBLIC And PRIVATE COMPANIES, BASED In ibase SOCIAL stamp

    Directory of Open Access Journals (Sweden)

    Alexandre Reis

    2008-01-01

    Full Text Available The present article intends to arguing the existing differences and similarities between Social Responsibility actions and praticals developed by the private and public companies. This comparative study of exploring character was carried with the companies owners of Social Stamp IBASE, wich published its Social Balances in the model considered for the institute in the year of 2004. For such, beyond the documentary research involving the published balances, a conceptual revision over the main subjects was necessary and also it constitutes part of the study. The joined results supply measurable and representative information about the main characteristics of social action of the companies, propitiating a comparative analysis and the emission of critical considerations, that do not finish themselves, but establishes a possibility of different readings concerning the models of social responsible management undertaken by companies from public and private segments.

  14. Deterministic transfer of two-dimensional materials by all-dry viscoelastic stamping

    International Nuclear Information System (INIS)

    Castellanos-Gomez, Andres; Buscema, Michele; Molenaar, Rianda; Singh, Vibhor; Janssen, Laurens; Van der Zant, Herre S J; Steele, Gary A

    2014-01-01

    The deterministic transfer of two-dimensional crystals constitutes a crucial step towards the fabrication of heterostructures based on the artificial stacking of two-dimensional materials. Moreover, controlling the positioning of two-dimensional crystals facilitates their integration in complex devices, which enables the exploration of novel applications and the discovery of new phenomena in these materials. To date, deterministic transfer methods rely on the use of sacrificial polymer layers and wet chemistry to some extent. Here, we develop an all-dry transfer method that relies on viscoelastic stamps and does not employ any wet chemistry step. This is found to be very advantageous to freely suspend these materials as there are no capillary forces involved in the process. Moreover, the whole fabrication process is quick, efficient, clean and it can be performed with high yield. (letter)

  15. Spectral analysis of postage stamps and banknotes from the region of Rijeka in Croatia

    Science.gov (United States)

    Jelovica Badovinac, I.; Orlić, N.; Lofrumento, C.; Dobrinić, J.; Orlić, M.

    2010-07-01

    Micro-Raman spectroscopy and X-ray emission spectroscopy induced using radioactive source have been applied to analyze two types of samples important for the history of Rijeka, Croatian port on the Adriatic Sea. In this paper we will present study of thirty-three original Hungarian postage stamps issued for Rijeka and overprinted with the word FIUME in 1918, after the World War I and the one-Lira banknotes (one original brown banknote and four trial prints: brown, blue, green and dark green) from Economy bank for Rijeka, Istria and Slovenian Littoral (1945-1947), the so-called Jugolire. This investigation was carried out to determine the differences between the original machine, original hand-made and fake overprints FIUME and to compare the pigments used on original banknote from circulation with the pigments on the trial prints.

  16. Large-area fabrication of patterned ZnO-nanowire arrays using light stamping lithography.

    Science.gov (United States)

    Hwang, Jae K; Cho, Sangho; Seo, Eun K; Myoung, Jae M; Sung, Myung M

    2009-12-01

    We demonstrate selective adsorption and alignment of ZnO nanowires on patterned poly(dimethylsiloxane) (PDMS) thin layers with (aminopropyl)siloxane self-assembled monolayers (SAMs). Light stamping lithography (LSL) was used to prepare patterned PDMS thin layers as neutral passivation regions on Si substrates. (3-Aminopropyl)triethoxysilane-based SAMs were selectively formed only on regions exposing the silanol groups of the Si substrates. The patterned positively charged amino groups define and direct the selective adsorption of ZnO nanowires with negative surface charges in the protic solvent. This procedure can be adopted in automated printing machines that generate patterned ZnO-nanowire arrays on large-area substrates. To demonstrate its usefulness, the LSL method was applied to prepare ZnO-nanowire transistor arrays on 4-in. Si wafers.

  17. Verification of human actions in SBO sequences with LOCA stamps in Westinghouse PWRs

    International Nuclear Information System (INIS)

    Queral, C.; Mena Rosell, L.; Jimenez Varas, G.

    2013-01-01

    The Fukushima accident has shown the need for tools and methodologies able to analyze human activities and / or capabilities of portable systems that has given the Spanish plants as a result of the stress tests . In this work we have applied the methodology of integrated safety analysis developed by the CSN , to SBO sequences with LOCA stamp. The aim is to show a methodology for testing the performances of the Emergency Operating Procedures and Guides Severe Accident Management. The simulations were performed with the tool SCAIS coupled to MAAP . The results show that there are human activities that may be beneficial in certain sequences but harmful in others. This type of problem is already known and referred to in the GGAS . However, FSR shows a practical way to check human actions cannot be obtained with other methods.

  18. Spectral analysis of postage stamps and banknotes from the region of Rijeka in Croatia

    Energy Technology Data Exchange (ETDEWEB)

    Jelovica Badovinac, I., E-mail: ijelov@phy.uniri.h [Department of Physics, University of Rijeka, Omladinska 14, 51000 Rijeka (Croatia); Orlic, N. [Department of Physics, University of Rijeka, Omladinska 14, 51000 Rijeka (Croatia); Lofrumento, C. [Dipartimento di Chimica, Universita di Firenze, Via della Lastruccia 3, 50019 Sesto Fiorentino (Italy); Dobrinic, J. [Faculty of Engineering, University of Rijeka, Vukovarska 58, 51000 Rijeka (Croatia); Orlic, M. [Department of Civil Engineering, Polytechnic of Zagreb, Av. V. Holjevca 15, 10000 Zagreb (Croatia)

    2010-07-21

    Micro-Raman spectroscopy and X-ray emission spectroscopy induced using radioactive source have been applied to analyze two types of samples important for the history of Rijeka, Croatian port on the Adriatic Sea. In this paper we will present study of thirty-three original Hungarian postage stamps issued for Rijeka and overprinted with the word FIUME in 1918, after the World War I and the one-Lira banknotes (one original brown banknote and four trial prints: brown, blue, green and dark green) from Economy bank for Rijeka, Istria and Slovenian Littoral (1945-1947), the so-called Jugolire. This investigation was carried out to determine the differences between the original machine, original hand-made and fake overprints FIUME and to compare the pigments used on original banknote from circulation with the pigments on the trial prints.

  19. Study of mechanical properties on powdermetalurgy aluminium matrix composites fabricated by stamping or extrusion

    International Nuclear Information System (INIS)

    Busquets, D.; Gomez, L.; Amigo, V.; Salvador-Moya, M. D.

    2005-01-01

    We have developed composite materials from AA6061 aluminium alloy powders used as matrix and ceramics powders of boron carbide, silicon carbide and boron nitride, used as reinforcements in 2.5, 5.0, 7.5 and 10% vol. by mechanical mixing and milling in planetary mill at 360 rpm vial velocity for 4 h followed of hot stamping and extrusion process on green compacts. Mechanical properties obtained from tensile tests are influenced by the heat treatment, reinforcement fractions and nature. Moreover, these mechanical characteristic are dependent from the processing route. Optical and Scanning Electron Microscopy analysis revealed the microstructure of materials and let describe the tripartite relation; structure-processing-properties, of the developed materials. (Author) 20 refs

  20. Spectral analysis of postage stamps and banknotes from the region of Rijeka in Croatia

    International Nuclear Information System (INIS)

    Jelovica Badovinac, I.; Orlic, N.; Lofrumento, C.; Dobrinic, J.; Orlic, M.

    2010-01-01

    Micro-Raman spectroscopy and X-ray emission spectroscopy induced using radioactive source have been applied to analyze two types of samples important for the history of Rijeka, Croatian port on the Adriatic Sea. In this paper we will present study of thirty-three original Hungarian postage stamps issued for Rijeka and overprinted with the word FIUME in 1918, after the World War I and the one-Lira banknotes (one original brown banknote and four trial prints: brown, blue, green and dark green) from Economy bank for Rijeka, Istria and Slovenian Littoral (1945-1947), the so-called Jugolire. This investigation was carried out to determine the differences between the original machine, original hand-made and fake overprints FIUME and to compare the pigments used on original banknote from circulation with the pigments on the trial prints.

  1. Discrimination between authentic and false tax stamps from liquor bottles using laser-induced breakdown spectroscopy and chemometrics

    International Nuclear Information System (INIS)

    Gonzaga, Fabiano Barbieri; Rocha, Werickson Fortunato de Carvalho; Correa, Deleon Nascimento

    2015-01-01

    This work describes the preliminary application of a compact and low-cost laser-induced breakdown spectroscopy (LIBS) instrument for falsification detection of tax stamps used in alcoholic beverages. The new instrument was based on a diode-pumped passively Q-switched Nd:YLF microchip laser and a mini-spectrometer containing a Czerny–Turner polichromator coupled to a non-intensified, non-gated, and non-cooled 2048 pixel linear sensor array (200 to 850 nm spectral range). Twenty-three tax stamp samples were analyzed by firing laser pulses within two different regions of each sample: a hologram and a blank paper region. For each acquired spectrum, the emitted radiation was integrated for 3000 ms under the continuous application of laser pulses at 100 Hz (integration of 300 plasmas). Principal component analysis (PCA) or hierarchical cluster analysis (HCA) of all emission spectra from the hologram or blank paper region revealed two well-defined groups of authentic and false samples. Moreover, for the hologram data, three subgroups of false samples were found. Additionally, partial least squares discriminant analysis (PLS-DA) was successfully applied for the detection of the false tax stamps using all emission spectra from hologram or blank paper region. The discrimination between the samples was mostly ascribed to different levels of calcium concentration in the samples. - Highlights: • Compact and low-cost laser-induced breakdown spectrometer • Analysis of tax stamps used in alcoholic beverages • Detection of false tax stamps using the LIBS spectra and chemometrics • Falsification detection ascribed to different levels of calcium concentration

  2. Discrimination between authentic and false tax stamps from liquor bottles using laser-induced breakdown spectroscopy and chemometrics

    Energy Technology Data Exchange (ETDEWEB)

    Gonzaga, Fabiano Barbieri, E-mail: fbgonzaga@inmetro.gov.br [Chemical Metrology Division, National Institute of Metrology, Quality and Technology (INMETRO), Av. Nossa Senhora das Graças, 50, Xerém, 25250-020 Duque de Caxias, RJ (Brazil); Rocha, Werickson Fortunato de Carvalho [Chemical Metrology Division, National Institute of Metrology, Quality and Technology (INMETRO), Av. Nossa Senhora das Graças, 50, Xerém, 25250-020 Duque de Caxias, RJ (Brazil); Correa, Deleon Nascimento [Technical–Scientific Police Superintendency, Criminalistic Institute Dr. Octávio Eduardo de Brito Alvarenga—IC-SPTC-SP, 05507-060 São Paulo, SP (Brazil)

    2015-07-01

    This work describes the preliminary application of a compact and low-cost laser-induced breakdown spectroscopy (LIBS) instrument for falsification detection of tax stamps used in alcoholic beverages. The new instrument was based on a diode-pumped passively Q-switched Nd:YLF microchip laser and a mini-spectrometer containing a Czerny–Turner polichromator coupled to a non-intensified, non-gated, and non-cooled 2048 pixel linear sensor array (200 to 850 nm spectral range). Twenty-three tax stamp samples were analyzed by firing laser pulses within two different regions of each sample: a hologram and a blank paper region. For each acquired spectrum, the emitted radiation was integrated for 3000 ms under the continuous application of laser pulses at 100 Hz (integration of 300 plasmas). Principal component analysis (PCA) or hierarchical cluster analysis (HCA) of all emission spectra from the hologram or blank paper region revealed two well-defined groups of authentic and false samples. Moreover, for the hologram data, three subgroups of false samples were found. Additionally, partial least squares discriminant analysis (PLS-DA) was successfully applied for the detection of the false tax stamps using all emission spectra from hologram or blank paper region. The discrimination between the samples was mostly ascribed to different levels of calcium concentration in the samples. - Highlights: • Compact and low-cost laser-induced breakdown spectrometer • Analysis of tax stamps used in alcoholic beverages • Detection of false tax stamps using the LIBS spectra and chemometrics • Falsification detection ascribed to different levels of calcium concentration.

  3. DOTD support for UTC project : travel time estimation using bluetooth, [research project capsule].

    Science.gov (United States)

    2013-10-01

    Travel time estimates are useful tools for measuring congestion in an urban area. Current : practice involves using probe vehicles or video cameras to measure travel time, but this is a laborintensive and expensive means of obtaining the information....

  4. Analysis characteristics determination of electrohydraulic control system operation to reduce the operation time of a powered roof support

    Science.gov (United States)

    Szurgacz, Dawid

    2018-01-01

    The article discusses basic functions of a powered roof support in a longwall unit. The support function is to provide safety by protecting mine workings against uncontrolled falling of rocks. The subject of the research includes the measures to shorten the time of roof support shifting. The roof support is adapted to transfer, in hazard conditions of rock mass tremors, dynamic loads caused by mining exploitation. The article presents preliminary research results on the time reduction of the unit advance to increase the extraction process and thus reduce operating costs. Conducted stand tests showed the ability to increase the flow for 3/2-way valve cartridges. The level of fluid flowing through the cartridges is adequate to control individual actuators.

  5. GIS oriented analysis of tourist time-space patterns to support sustainable tourism development

    NARCIS (Netherlands)

    Knaap, van der W.G.M.

    1999-01-01

    Tourism and tourism development create major changes in the environment. To determine their impact on environmental sustainability, it is necessary to understand tourist behaviour. Time, space and context are important components in describing tourist time-space behaviour. Tourist time-space

  6. The Role of Early Maternal Support in Balancing Full-Time Work and Infant Exclusive Breastfeeding: A Qualitative Study.

    Science.gov (United States)

    Pounds, Lea; Fisher, Christopher M; Barnes-Josiah, Debora; Coleman, Jason D; Lefebvre, R Craig

    Support of others is a key factor for mothers who choose to breastfeed their infants, including those who balance work outside the home and breastfeeding. However, little research has been done to understand how maternal support during the postpartum period impacts mothers' ability to later balance work and breastfeeding, in particular full-time work and exclusive breastfeeding. The results of this qualitative study indicate that the timing of support plays a key role in mothers' ability to successfully overcome barriers during the early postpartum period, thus building maternal self-efficacy in addressing problems encountered when they return to work. To understand the experience of low-income women who successfully balance full-time work and exclusive breastfeeding for the recommended 6 months, interviews were conducted with women who met study criteria for income level, work status, and exclusive breastfeeding. Breastfeeding peer counselors were also interviewed as key informants. Interviews were recorded, transcribed, and coded for themes. The results of both sets of interviews were triangulated with a focused literature review to assure the soundness of the qualitative analysis. Timing of support included acute support, such as help establishing a successful latch needed during the first 2 weeks after delivery, to deal with breastfeeding problems that mothers perceived as being mentally and emotionally overwhelming and longer-term support needed to overcome problems perceived as being less intense. The research invites further exploration into the relationship between breastfeeding support provided by mothers' support system, including healthcare professionals, during the postpartum period and rates of breastfeeding duration and exclusivity.

  7. Optimization of the blankholder force distribution with application to the stamping of a car front door panel (Numisheet'99)

    International Nuclear Information System (INIS)

    Ayed, L. Ben; Delameziere, A.; Batoz, J.L.; Knopf-Lenoir, C.

    2005-01-01

    New materials such as dual phase steel or aluminium and complex geometries of industrial parts increase the difficulties to obtain a defect free part by stamping. One way of solution is a better regulation of the blankholder pressures. Our work is based on an original idea of Siegert, Haeussermann and Haller. The goal is to control the movement of the blank under the blankholder. Thanks to a deformable flexible blankholder, it is possible to create some independent zones. In each zone, a blankholder force can be applied on the sheet, so that a strong force can hold the blank in a zone, and a smaller one can let it move in another zone. The methodology is presented as well as some results dealing with the optimization of the blankholder force considering the drawing of a front door panel (Numisheet'99 benchmark test). The numerical simulations are performed using ABAQUS Explicit. The parameters of the finite element model (mesh density, speed of punch) are set to achieve a good prediction with a minimum simulation time. The objective function is defined to minimize the work of the punch. Three inequality constraints functions were defined to avoid necking and wrinkling. To avoid necking, the major stress of the blank is limited to a value, which is determined by using the modified maximum force criterion (MMFC). To avoid wrinkling, under the blankholder, the angle between the blankholder surface and an element of the blank is limited to a value set by the user, as proposed by Gelin and Labergere. However, in the useful part of the workpiece, the major stress is limited to a value, which was proposed by Brunet, Batoz and Bouabdallah. For the localization of the optimum, we use a response surface method computed with a diffuse approximation and coupled with an adaptative strategy to update the research space

  8. Optimization of the blankholder force distribution with application to the stamping of a car front door panel (Numisheet'99)

    Science.gov (United States)

    Ayed, L. Ben; Delamézière, A.; Batoz, J. L.; Knopf-Lenoir, C.

    2005-08-01

    New materials such as dual phase steel or aluminium and complex geometries of industrial parts increase the difficulties to obtain a defect free part by stamping. One way of solution is a better regulation of the blankholder pressures. Our work is based on an original idea of Siegert, Häussermann and Haller. The goal is to control the movement of the blank under the blankholder. Thanks to a deformable flexible blankholder, it is possible to create some independent zones. In each zone, a blankholder force can be applied on the sheet, so that a strong force can hold the blank in a zone, and a smaller one can let it move in another zone. The methodology is presented as well as some results dealing with the optimization of the blankholder force considering the drawing of a front door panel (Numisheet'99 benchmark test). The numerical simulations are performed using ABAQUS Explicit. The parameters of the finite element model (mesh density, speed of punch) are set to achieve a good prediction with a minimum simulation time. The objective function is defined to minimize the work of the punch. Three inequality constraints functions were defined to avoid necking and wrinkling. To avoid necking, the major stress of the blank is limited to a value, which is determined by using the modified maximum force criterion (MMFC). To avoid wrinkling, under the blankholder, the angle between the blankholder surface and an element of the blank is limited to a value set by the user, as proposed by Gelin and Labergere. However, in the useful part of the workpiece, the major stress is limited to a value, which was proposed by Brunet, Batoz and Bouabdallah. For the localization of the optimum, we use a response surface method computed with a diffuse approximation and coupled with an adaptative strategy to update the research space.

  9. Real time data acquisition and processing system software supported by RDOS

    International Nuclear Information System (INIS)

    Yang Huimin; Chou Gongchun; Hao Shuxiang

    1982-01-01

    The paper describes a system software supported by RDOS operating system for management and supervision a multiuser nuclear spectrum data acquisition and processing system to be made of NOVA/840 computer. The system has manifold functions including four direct address data acquisition channels. One multi-dimension nuclear data acquisition channel, four scalers and four automatic control entrances. Every channel is used competitively by each user. The system's management and all processing functions are performed by system software. The architecture of the system can renew according to users' requirement with support of the system software.This article explains the logical structure of the system software and discusses some technical keys

  10. Cage for shield-type support. Schildausbaugestell

    Energy Technology Data Exchange (ETDEWEB)

    Harryers, W; Blumenthal, G; Irresberger, H

    1981-08-13

    A cage for shield-type support containing a fracture shield supported by a hydraulic stamp and a projecting roof bar was constructed in such a way that no cellular shirt is needed to timber the caved room. The roof bar which is linked at a joint axis at the face-side end of the fracture shield is formed at the face side as a multiply foldable bar. (HGOE).

  11. Social support and leisure-time physical activity: longitudinal evidence from the Brazilian Pró-Saúde cohort study.

    Science.gov (United States)

    Oliveira, Aldair J; Lopes, Claudia S; de Leon, Antônio C Ponce; Rostila, Mikael; Griep, Rosane H; Werneck, Guilherme L; Faerstein, Eduardo

    2011-07-26

    Although social support has been observed to exert a beneficial influence on leisure-time physical activity (LTPA), multidimensional approaches examining social support and prospective evidence of its importance are scarce. The purpose of this study was to investigate how four dimensions of social support affect LTPA engagement, maintenance, type, and time spent by adults during a two-year follow-up. This paper reports on a longitudinal study of 3,253 non-faculty public employees at a university in Rio de Janeiro (the Pró-Saúde study). LTPA was evaluated using a dichotomous question with a two-week reference period, and further questions concerning LTPA type (individual or group) and time spent on the activity. Social support was measured by the Medical Outcomes Study Social Support Scale (MOS-SSS). To assess the association between social support and LTPA, two different statistical models were used: binary and multinomial logistic regression models for dichotomous and polytomous outcomes, respectively. Models were adjusted separately for those who began LTPA in the middle of the follow up (engagement group) and for those who had maintained LTPA since the beginning of the follow up (maintenance group). After adjusting for confounders, statistically significant associations (p time spent on LTPA (OR = 2.01; 95% CI 1.2-3.9). In the maintenance group, material support was associated with group LTPA (OR = 1.80; 95% CI; 1.1-3.1) and the positive social interaction dimension was associated with time spent on LTPA (OR = 1.65; 95% CI; 1.1-2.7). All dimensions of social support influenced LTPA type or the time spent on the activity. However, our findings suggest that social support is more important in engagement than in maintenance. This finding is important, because it suggests that maintenance of LTPA must be associated with other factors beyond the individual's level of social support, such as a suitable environment and social/health policies directed towards the

  12. Targeted, Timely, Learning Support for International Students: One Australian University's Approach

    Science.gov (United States)

    Baird, Craig

    2012-01-01

    This paper documents the approach taken by an Australian University to enhance student study skills, development of academic language, and writing skills. The Curtin Business School (CBS) has the only fully faculty-based student learning support centre at Curtin University in Western Australia. Called the CBS Communication Skills Centre (CSC) it…

  13. It's Story Time!: Exploring the Potential of Multimodality in Oral Storytelling to Support Children's Vocabulary Learning

    Science.gov (United States)

    Lwin, Soe Marlar

    2016-01-01

    Although many studies have been done on the benefits of parent/teacher-child interactions during shared storybook reading or read'aloud sessions, very few have examined the potential of professional storytellers' oral discourse to support children's vocabulary learning. In those storytelling sessions conducted by professional storytellers, the…

  14. The Value of Caregiver Time: Costs of Support and Care for Individuals Living with Autism Spectrum Disorder

    Directory of Open Access Journals (Sweden)

    Carolyn Dudley

    2016-01-01

    Full Text Available WHY IS THIS AN IMPORTANT ISSUE? An estimated 1 in 86 children are diagnosed with Autism Spectrum Disorder (ASD1 making it the most commonly diagnosed childhood neurological condition in Canada.2 The true costs of lifelong support for people living with ASD3 are often underestimated and fail to acknowledge the value of caregiver time over the lifespan. Significant gaps in publically provided support systems leave the cost burden to be picked up by families. Relying on continued family supports where community services are fragmented or unavailable is not a sustainable approach. WHAT DOES THE RESEARCH TELL US? A continuum of supports are needed Most people living with ASD need supports that range from occasional assistance with higher level tasks, like organizing appointments or banking, to those who need continuous help with daily living.4 Areas where supportive care may be needed can be categorized broadly to include: self care, home living, service co-ordination, personal organization, health and safety management, adult day opportunities/employment, transportation, advocacy and social skills. These supports are most successful when they address the individual’s uniqueness in terms of communication, social, sensory, behavioural needs and physical and/or mental health conditions. Currently there are a lack of available supports, limiting opportunities for socialization, employment and residential living resulting in reduced independence for adults with ASD.

  15. A HARDWARE SUPPORTED OPERATING SYSTEM KERNEL FOR EMBEDDED HARD REAL-TIME APPLICATIONS

    NARCIS (Netherlands)

    COLNARIC, M; HALANG, WA; TOL, RM

    1994-01-01

    The concept of the kernel, i.e. the time critical part of a real-time operating system, and its dedicated co-processor, especially tailored for embedded applications, are presented. The co-processor acts as a system controller and operates in conjunction with one or more conventional processors in

  16. Mentorship Efforts to Support Part-Time Social Work Faculty Members

    Science.gov (United States)

    Shobe, Marcia A.; Murphy-Erby, Yvette; Sparks, Jared

    2014-01-01

    Social work faculty experience increasing demands to develop and maintain a research portfolio that includes external funding and publications. Given the increase in research expectations, more part-time instructors are needed to teach courses. In addition to the literature review, we briefly describe a pilot part-time faculty mentorship project…

  17. Optimization of Partitioned Architectures to Support Soft Real-Time Applications

    DEFF Research Database (Denmark)

    Tamas-Selicean, Domitian; Pop, Paul

    2014-01-01

    In this paper we propose a new Tabu Search-based design optimization strategy for mixed-criticality systems implementing hard and soft real-time applications on the same platform. Our proposed strategy determined an implementation such that all hard real-time applications are schedulable and the ......In this paper we propose a new Tabu Search-based design optimization strategy for mixed-criticality systems implementing hard and soft real-time applications on the same platform. Our proposed strategy determined an implementation such that all hard real-time applications are schedulable...... and the quality of service of the soft real-time tasks is maximized. We have evaluated our strategy using an aerospace case study....

  18. A multisite randomized controlled trial on time to self-support among sickness absence beneficiaries

    DEFF Research Database (Denmark)

    Nielsen, Maj Britt D.; Vinsløv Hansen, Jørgen; Aust, Birgit

    2015-01-01

    BACKGROUND: In 2010, the Danish Government launched the Danish national return-to-work (RTW) programme to reduce sickness absence and promote labour market attainment. Multidisciplinary teams delivered the RTW programme, which comprised a coordinated, tailored and multidisciplinary effort (CTM......) for sickness absence beneficiaries at high risk for exclusion from the labour market. The aim of this article was to evaluate the effectiveness of the RTW programme on self-support. METHODS: Beneficiaries from three municipalities (denoted M1, M2 and M3) participated in a randomized controlled trial. We.......54-0.95). In M1, we found no difference between the two groups (HR = 0.99, 95% CI: 0.84-1.17). CONCLUSION: The effect of the CTM programme on return to self-support differed substantially across the three participating municipalities. Thus, generalizing the study results to other Danish municipalities...

  19. Predictive Analytics to Support Real-Time Management in Pathology Facilities.

    Science.gov (United States)

    Lessard, Lysanne; Michalowski, Wojtek; Chen Li, Wei; Amyot, Daniel; Halwani, Fawaz; Banerjee, Diponkar

    2016-01-01

    Predictive analytics can provide valuable support to the effective management of pathology facilities. The introduction of new tests and technologies in anatomical pathology will increase the volume of specimens to be processed, as well as the complexity of pathology processes. In order for predictive analytics to address managerial challenges associated with the volume and complexity increases, it is important to pinpoint the areas where pathology managers would most benefit from predictive capabilities. We illustrate common issues in managing pathology facilities with an analysis of the surgical specimen process at the Department of Pathology and Laboratory Medicine (DPLM) at The Ottawa Hospital, which processes all surgical specimens for the Eastern Ontario Regional Laboratory Association. We then show how predictive analytics could be used to support management. Our proposed approach can be generalized beyond the DPLM, contributing to a more effective management of pathology facilities and in turn to quicker clinical diagnoses.

  20. Predictive Analytics to Support Real-Time Management in Pathology Facilities

    Science.gov (United States)

    Lessard, Lysanne; Michalowski, Wojtek; Chen Li, Wei; Amyot, Daniel; Halwani, Fawaz; Banerjee, Diponkar

    2016-01-01

    Predictive analytics can provide valuable support to the effective management of pathology facilities. The introduction of new tests and technologies in anatomical pathology will increase the volume of specimens to be processed, as well as the complexity of pathology processes. In order for predictive analytics to address managerial challenges associated with the volume and complexity increases, it is important to pinpoint the areas where pathology managers would most benefit from predictive capabilities. We illustrate common issues in managing pathology facilities with an analysis of the surgical specimen process at the Department of Pathology and Laboratory Medicine (DPLM) at The Ottawa Hospital, which processes all surgical specimens for the Eastern Ontario Regional Laboratory Association. We then show how predictive analytics could be used to support management. Our proposed approach can be generalized beyond the DPLM, contributing to a more effective management of pathology facilities and in turn to quicker clinical diagnoses. PMID:28269873

  1. Real-Time Support of Pediatric Diabetes Self-Care by a Transport Team

    OpenAIRE

    Franklin, Brandi E.; Crisler, S. Crile; Shappley, Rebekah; Armour, Meri M.; McCommon, Dana T.; Ferry, Robert J.

    2013-01-01

    OBJECTIVE The study seeks to improve access for underserved patients via novel integration of Pedi-Flite (a critical care transport team) and to validate whether this safely enhances diabetes care and effectively expands the endocrine workforce. RESEARCH DESIGN AND METHODS The study retrospectively analyzed pager service use in a cohort of established diabetic patients (n = 979) after inception of Pedi-Flite support. Outcomes included incidence and severity of recurrent diabetic ketoacidosis ...

  2. ASSOCIATIONS OF MOTHERS IN PROTECTION AND SUPPORTING OF BREAST FEEDING: HISTORY AND PRESENT TIMES

    Directory of Open Access Journals (Sweden)

    L.V. Abol’yan

    2010-01-01

    Full Text Available The article presents a data on creation of social associations of mothers — groups of maternal supporting of breast feeding in continuation with international initiative «Baby-Friendly Hospital» of WHO/UNICEF in Russia. As breast feeding is mostly a medical problem usual for medical personnel in obstetrical and children’s medical institution (obstetricians-gynecologists, neonatologists, pediatricians, there is a question on legality of such groups’ presence and its competence, relations to medical personnel, forms of work. The Soviet public health had wide experience of successful collaboration of public activists of Russian Red Cross Society and Health Care Administrations in performance of prophylactic and health-improving measures and hygienic education among population. Successful activity of voluntary associations supporting breast feeding depends on collaboration with medical personnel, development of scientifically-based programs of mothers-consultants education, and presence of informational, methodical and hygienical educational materials.Key words: breast feeding, groups of maternal support.(Voprosy sovremennoi pediatrii — Current Pediatrics. 2010;9(2:15-18

  3. Constraints on the use of 137Cs as a time-marker to support CRS and SIT chronologies

    International Nuclear Information System (INIS)

    Abril, J.M.

    2004-01-01

    CRS and SIT are two 210 Pb-based models widely used in the radiometric dating of recent sediments. 210 Pb chronologies should be validated using at least one independent tracer, such as 137 Cs. This paper demonstrates that simple methods based on the identification of 137 Cs fallout peaks cannot provide a definitive support for CRS and SIT chronologies. Two main arguments will support this assertion: Firstly, the 137 Cs time-marks cannot support a CRS or SIT chronology if the derived sedimentation rates cannot explain the whole 137 Cs activity profile without postulating mixing. Secondly, the support by the 137 Cs time-marks for a given CRS or SIT chronology cannot be considered as definitive if other dating models can equally explain the whole set of data, thereby producing a different chronology. Several case studies selected from the literature are used to support the present discussion. - Simple methods based on the identification of 137 Cs fallout peaks cannot provide a definite support for CRS and SIT chronologies

  4. Real-Time Reliability Verification for UAV Flight Control System Supporting Airworthiness Certification.

    Science.gov (United States)

    Xu, Haiyang; Wang, Ping

    2016-01-01

    In order to verify the real-time reliability of unmanned aerial vehicle (UAV) flight control system and comply with the airworthiness certification standard, we proposed a model-based integration framework for modeling and verification of time property. Combining with the advantages of MARTE, this framework uses class diagram to create the static model of software system, and utilizes state chart to create the dynamic model. In term of the defined transformation rules, the MARTE model could be transformed to formal integrated model, and the different part of the model could also be verified by using existing formal tools. For the real-time specifications of software system, we also proposed a generating algorithm for temporal logic formula, which could automatically extract real-time property from time-sensitive live sequence chart (TLSC). Finally, we modeled the simplified flight control system of UAV to check its real-time property. The results showed that the framework could be used to create the system model, as well as precisely analyze and verify the real-time reliability of UAV flight control system.

  5. Data mining tools for the support of traffic signal timing plan development in arterial networks

    Science.gov (United States)

    2001-05-01

    Intelligent transportation systems (ITS) include large numbers of traffic sensors that collect enormous quantities of data. The data provided by ITS is necessary for advanced forms of control; however, basic forms of control, primarily time-of-day (T...

  6. Model of observed stochastic balance between work and free time supporting the LQTAI definition

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    2008-01-01

    A balance differential equation between free time and money-producing work time on the national economy level is formulated in a previous paper in terms of two dimensionless quantities, the fraction of work time and the total productivity factor defined as the ratio of the Gross Domestic Product...... significant systematically balance influencing parameters on the macro economical level than those considered in the definition in the previous paper of the Life Quality Time Allocation Index....... to the total salary paid in return for work. Among the solutions there is one relation that compares surprisingly well with the relevant sequences of Danish data spanning from 1948 to 2003, and also with similar data from several other countries except for slightly different model parameter values. Statistical...

  7. Detection and Characterization of Equatorial Scintillation for Real-Time Operational Support

    National Research Council Canada - National Science Library

    McNeil, W

    1997-01-01

    The Phillips Laboratory Scintillation Network Decision Aid (PL-SCINDA) is a software tool which uses real-time data from remote sites to model ionospheric plasma depletions in the equatorial region...

  8. Towards harnessing theories through tool support for hard real-time Java programming

    DEFF Research Database (Denmark)

    Bøgholm, Thomas; Frost, Christian; Hansen, Rene Rydhof

    2013-01-01

    We present a rationale for a selection of tools that assist developers of hard real-time applications to verify that programs conform to a Java real-time profile and that platform-specific resource constraints are satisfied. These tools are specialised instances of more generic static analysis...... and model checking frameworks. The concepts are illustrated by two case studies, and the strengths and the limitations of the tools are discussed....

  9. Towards harnessing theories through tool support for hard real-time Java programming

    DEFF Research Database (Denmark)

    Søndergaard, Hans; Bøgholm, Thomas; Frost, Christian

    2012-01-01

    We present a rationale for a selection of tools that assist developers of hard real-time applications to verify that programs conform to a Java real-time profile and that platform-specific resource constraints are satisfied. These tools are specialised instances of more generic static analysis...... and model checking frameworks. The concepts are illustrated by two case studies, and the strengths and the limitations of the tools are discussed....

  10. Jig-Time and Navigational Support in the Control of Road Transport

    Directory of Open Access Journals (Sweden)

    Nataliya Grigorievna Kuftinova

    2015-05-01

    Full Text Available In this article the question of the direction of use of jig-time and navigation providing the motor transport in the field of steering of transportation process is considered. The solution of transport tasks demand existence of jig-time and navigation providing (JTNP based on use of the global navigation satellite systems (GNSS, geographical information systems (GIS, means and technologies of telematics.

  11. Automatic Generation of Cycle-Approximate TLMs with Timed RTOS Model Support

    Science.gov (United States)

    Hwang, Yonghyun; Schirner, Gunar; Abdi, Samar

    This paper presents a technique for automatically generating cycle-approximate transaction level models (TLMs) for multi-process applications mapped to embedded platforms. It incorporates three key features: (a) basic block level timing annotation, (b) RTOS model integration, and (c) RTOS overhead delay modeling. The inputs to TLM generation are application C processes and their mapping to processors in the platform. A processor data model, including pipelined datapath, memory hierarchy and branch delay model is used to estimate basic block execution delays. The delays are annotated to the C code, which is then integrated with a generated SystemC RTOS model. Our abstract RTOS provides dynamic scheduling and inter-process communication (IPC) with processor- and RTOS-specific pre-characterized timing. Our experiments using a MP3 decoder and a JPEG encoder show that timed TLMs, with integrated RTOS models, can be automatically generated in less than a minute. Our generated TLMs simulated three times faster than real-time and showed less than 10% timing error compared to board measurements.

  12. Tech Select Decision Aide: A Mobile Application to Facilitate Just-in-Time Decision Support for Instructional Designers

    Science.gov (United States)

    Dabbagh, Nada; Fake, Helen

    2017-01-01

    With the ubiquitous use of mobile technologies and the increasing demand for just-in-time training, there is a need to prepare and support instructional designers and educators to meet the pedagogical and technological development requirements of their target audience in the most effective and efficient way. This paper reviews the iterative…

  13. Assessment of Public Schools' Out-of-School Time Academic Support Programs with Participant-Oriented Evaluation

    Science.gov (United States)

    Berk, Saban

    2018-01-01

    Using the participants-oriented approach, this study evaluated public schools' out-of-school time academic support programs, corresponding to the corrective/enrichment stage of Bloom's Mastery Learning Model and offered outside formal education's weekday hours and on weekends. Study participants included 50 principals, 110 teachers, 170 students…

  14. Using Just-in-Time Information to Support Scientific Discovery Learning in a Computer-Based Simulation

    Science.gov (United States)

    Hulshof, Casper D.; de Jong, Ton

    2006-01-01

    Students encounter many obstacles during scientific discovery learning with computer-based simulations. It is hypothesized that an effective type of support, that does not interfere with the scientific discovery learning process, should be delivered on a "just-in-time" base. This study explores the effect of facilitating access to…

  15. Supporting Youth with Special Needs in Out-of-School Time: A Study of OST Providers in New Jersey

    Science.gov (United States)

    Sharp, Jane; Rodas, Elizabeth Rivera; Sadovnik, Alan R.

    2012-01-01

    Although the Americans with Disabilities Act (ADA) of 1990 requires accommodations for individuals with disabilities in community settings, many out-of-school time (OST) programs struggle to successfully support youth with special needs. Programs that fully include children with special needs are less available for school-age children and…

  16. Automatic real time drilling support on Ekofisk utilizing eDrilling

    Energy Technology Data Exchange (ETDEWEB)

    Rommetveit, Rolv; Bjorkevoll, Knut S.; Halsey, George W.; Kluge, Roald; Molde, Dag Ove; Odegard, Sven Inge [SINTEF Petroleum Research, Trondheim (Norway); Herbert, Mike [HITEC Products Drilling, Stavanger (Norway); ConocoPhillips Norge, Stavanger (Norway)

    2008-07-01

    eDrilling is a new and innovative system for real time drilling simulation, 3D visualization and control from a remote drilling expert centre. The concept uses all available real time drilling data (surface and downhole) in combination with real time modelling to monitor and optimize the drilling process. This information is used to visualize the wellbore in 3D in real time. eDrilling has been implemented in an Onshore Drilling Center in Norway. The system is composed of the following elements, some of which are unique and ground-breaking: an advanced and fast Integrated Drilling Simulator which is capable to model the different drilling sub-processes dynamically, and also the interaction between these sub-processes in real time; automatic quality check and corrections of drilling data; making them suitable for processing by computer models; real time supervision methodology for the drilling process using time based drilling data as well as drilling models / the integrated drilling simulator; methodology for diagnosis of the drilling state and conditions. This is obtained from comparing model predictions with measured data. Advisory technology for more optimal drilling. A Virtual Wellbore, with advanced visualization of the downhole process. Dat low and computer infrastructure. e-Drilling has been implemented in an Onshore Drilling Center on Ekofisk in Norway. The system is being used on drilling operations, and experiences from its use are presented. The supervision and diagnosis functionalities have been useful in particular, as the system has given early warnings on ECD and friction related problems. This paper will present the eDrilling system as well as experiences from its use. (author)

  17. The Role of Compensation Criteria to Minimize Face-Time Bias and Support Faculty Career Flexibility

    Directory of Open Access Journals (Sweden)

    Lydia Pleotis Howell MD

    2016-02-01

    Full Text Available Work-life balance is important to recruitment and retention of the younger generation of medical faculty, but medical school flexibility policies have not been fully effective. We have reported that our school’s policies are underutilized due to faculty concerns about looking uncommitted to career or team. Since policies include leaves and accommodations that reduce physical presence, faculty may fear “face-time bias,” which negatively affects evaluation of those not “seen” at work. Face-time bias is reported to negatively affect salary and career progress. We explored face-time bias on a leadership level and described development of compensation criteria intended to mitigate face-time bias, raise visibility, and reward commitment and contribution to team/group goals. Leaders from 6 partner departments participated in standardized interviews and group meetings. Ten compensation plans were analyzed, and published literature was reviewed. Leaders did not perceive face-time issues but saw team pressure and perception of availability as performance motivators. Compensation plans were multifactor productivity based with many quantifiable criteria; few addressed team contributions. Using these findings, novel compensation criteria were developed based on a published model to mitigate face-time bias associated with team perceptions. Criteria for organizational citizenship to raise visibility and reward group outcomes were included. We conclude that team pressure and perception of availability have the potential to lead to bias and may contribute to underuse of flexibility policies. Recognizing organizational citizenship and cooperative effort via specific criteria in a compensation plan may enhance a culture of flexibility. These novel criteria have been effective in one pilot department.

  18. AmbientRT - real time system software support for data centric sensor networks

    NARCIS (Netherlands)

    Hofmeijer, T.J.; Dulman, S.O.; Jansen, P.G.; Havinga, Paul J.M.

    We present the architecture and design of a real time operating system for mobile wireless sensor networks. AmbientRT is being developed for environments with very limited resources in order to relieve the burden of the developer and to efficiently use the resources of the node. This paper presents

  19. LO + EPSS = Just-in-Time Reuse of Content to Support Employee Performance

    Science.gov (United States)

    Nguyen, Frank; Hanzel, Matthew

    2007-01-01

    Those involved in training know that creating instructional materials can become a tedious, repetitive process. They also know that business conditions often require training interventions to be delivered in ways that are not ideally structured or timed. This article examines the notion that learning objects can be reused and adapted for…

  20. Using Part-Time Working to Support Graduate Employment: Needs and Perceptions of Employers

    Science.gov (United States)

    Evans, Carl; Maxfield, Tim; Gbadamosi, Gbolahan

    2015-01-01

    An exploration of the value attached to the work experience of graduates, and particularly the value of part-time working whilst studying for a degree, from an employer's perspective, is reported. A documentary analysis of graduate recruiters was conducted to assess the extent to which work experience was specified for graduate employment…

  1. AmbientRT - real time system software support for data centric sensor networks

    NARCIS (Netherlands)

    Hofmeijer, T.J.; Dulman, S.O.; Jansen, P.G.; Havinga, Paul J.M.

    2004-01-01

    We present the architecture and design of a real time operating system for mobile wireless sensor networks. AmbientRT is being developed for environments with very limited resources in order to relieve the burden of the developer and to efficiently use the resources of the node. This paper presents

  2. A generalized Web Service response time metric to support collaborative and corroborative Web Service monitoring

    CSIR Research Space (South Africa)

    Makitla, I

    2015-12-01

    Full Text Available In this paper, we describe the development of a generalized metric for computing response time of a web service. Such a generalized metric would help to develop consensus with regards to the meanings of contracted Quality of Service (QoS) parameters...

  3. Real Time Space Weather Support for Chandra X-ray Observatory Operations

    Science.gov (United States)

    O'Dell, S. L.; Miller, S.; Minow, J. I.; Wolk, S.; Aldcroft, T. L.; Spitzbart, B. D.; Swartz, D. A.

    2012-12-01

    NASA launched the Chandra X-ray Observatory in July 1999. Soon after first light in August 1999, however, degradation in the energy resolution and charge transfer efficiency of the Advanced CCD Imaging Spectrometer (ACIS) x-ray detectors was observed. The source of the degradation was quickly identified as radiation damage in the charge-transfer channel of the front-illuminated CCDs, by weakly penetrating ("soft", 100-500 keV) protons as Chandra passed through the Earth's radiation belts and ring currents. As soft protons were not considered a risk to spacecraft health before launch, the only on-board radiation monitoring system is the Electron, Proton, and Helium Instrument (EPHIN) which was included on Chandra with the primary purpose of monitoring energetic solar particle events. Further damage to the ACIS detector has been successfully mitigated through a combination of careful mission planning, autonomous on-board radiation protection, and manual intervention based upon real-time monitoring of the soft-proton environment. The AE-8 and AP-8 trapped radiation models and Chandra Radiation Models are used to schedule science operations in regions of low proton flux. EPHIN has been used as the primary autonomous in-situ radiation trigger; but, it is not sensitive to the soft protons that damage the front-illuminated CCDs. Monitoring of near-real-time space weather data sources provides critical information on the proton environment outside the Earth's magnetosphere due to solar proton events and other phenomena. The operations team uses data from the Geostationary Operational Environmental Satellites (GOES) to provide near-real-time monitoring of the proton environment; however, these data do not give a representative measure of the soft-proton (real-time data provided by NOAA's Space Weather Prediction Center. This presentation will discuss radiation mitigation against proton damage, including models and real-time data sources used to protect the ACIS detector

  4. Perioprosthetic and Implant-Supported Rehabilitation of Complex Cases: Clinical Management and Timing Strategy.

    Science.gov (United States)

    Landi, Luca; Piccinelli, Stefano; Raia, Roberto; Marinotti, Fabio; Manicone, Paolo Francesco

    2016-01-01

    Treatment of complex perioprosthetic cases is one of the clinical challenges of everyday practice. Only a complete and thorough diagnostic setup may allow the clinician to formulate a realistic prognosis to select the abutments to support prosthetic rehabilitation. Clinical, radiographic, or laboratory parameters used separately are useless to correctly assign a reliable prognosis to single teeth except in the case of a clearly hopeless tooth. Therefore, it is crucial to gather the greatest quantity of data to determine the role that every single element can play in the prosthetic rehabilitation of the case. The following report deals with the management of a multidisciplinary periodontally compromised case in which a treatment strategy and chronology were designed to reach clinical predictability while reducing the duration of the therapy.

  5. Perioprosthetic and Implant-Supported Rehabilitation of Complex Cases: Clinical Management and Timing Strategy

    Directory of Open Access Journals (Sweden)

    Luca Landi

    2016-01-01

    Full Text Available Treatment of complex perioprosthetic cases is one of the clinical challenges of everyday practice. Only a complete and thorough diagnostic setup may allow the clinician to formulate a realistic prognosis to select the abutments to support prosthetic rehabilitation. Clinical, radiographic, or laboratory parameters used separately are useless to correctly assign a reliable prognosis to single teeth except in the case of a clearly hopeless tooth. Therefore, it is crucial to gather the greatest quantity of data to determine the role that every single element can play in the prosthetic rehabilitation of the case. The following report deals with the management of a multidisciplinary periodontally compromised case in which a treatment strategy and chronology were designed to reach clinical predictability while reducing the duration of the therapy.

  6. The ALTA global positioning satellite based timing system

    CERN Document Server

    Brouwer, W; Caron, B; Hewlett, J C; Holm, L; Hamilton, A H; McDonald, W J; Pinfold, J L; Schaapman, J R; Soluk, R A; Wampler, L J

    2002-01-01

    The Alberta Large-area Time-coincidence Array (ALTA) experiment uses a number of scintillation detector systems to form a sparse very large area cosmic air-shower detection array. An important scientific goal of the ALTA collaboration is to search for coincidences in the ALTA array due to large area cosmic ray phenomena. A local cosmic ray event, determined by a coincidence of the triplet of cosmic ray detectors forming a local detector system, is time stamped with a temporal coordinate obtained from a GPS receiver. The readout of the data, the local coincidence and the GPS time stamp are all performed in the local readout crate. This time stamp, along with the local shower direction is used to search for coincidences within the large area array. Using two GPS receivers and duplicate sets of ALTA electronics the timing resolution of the GPS time difference between sites was estimated to be 16 ns.

  7. Social support at work and leisure time and its association with self-rated health and sickness absence.

    Science.gov (United States)

    Falkenberg, A; Nyfjäll, M; Hellgren, C; Vingård, E

    2012-01-01

    The aim of this longitudinal study is to investigate how different aspects of social support at work and in leisure time are associated with self rated health and sickness absence. The 541 participants in the study were representative for a working population in the public sector in Sweden with a majority being woman. Most of the variables were created from data from a questionnaire in March-April 2005. There were four independent variables and two dependent variables. The dependent were based on data from November 2006. A logistic regression model was used for the analysis of associations. A separate model was adapted for each of the explanatory variables for each outcome, which gave five models per independent variable. The study has given a greater awareness of the importance of employees receiving social support, regardless of type of support or from whom the support is coming. Social support has a strong association with SRH in a longitudinal perspective and no association between social support and sickness absence.

  8. All-silica nanofluidic devices for DNA-analysis fabricated by imprint of sol-gel silica with silicon stamp

    DEFF Research Database (Denmark)

    Mikkelsen, Morten Bo Lindholm; Letailleur, Alban A; Søndergård, Elin

    2011-01-01

    We present a simple and cheap method for fabrication of silica nanofluidic devices for single-molecule studies. By imprinting sol-gel materials with a multi-level stamp comprising micro- and nanofeatures, channels of different depth are produced in a single process step. Calcination of the imprin......We present a simple and cheap method for fabrication of silica nanofluidic devices for single-molecule studies. By imprinting sol-gel materials with a multi-level stamp comprising micro- and nanofeatures, channels of different depth are produced in a single process step. Calcination...... of the imprinted hybrid sol-gel material produces purely inorganic silica, which has very low autofluorescence and can be fusion bonded to a glass lid. Compared to top-down processing of fused silica or silicon substrates, imprint of sol-gel silica enables fabrication of high-quality nanofluidic devices without...

  9. Fabrication of Glass Microchannel via Glass Imprinting using a Vitreous Carbon Stamp for Flow Focusing Droplet Generator

    Science.gov (United States)

    Refatul Haq, Muhammad; Kim, Youngkyu; Kim, Jun; Oh, Pyoung-hwa; Ju, Jonghyun; Kim, Seok-Min; Lim, Jiseok

    2017-01-01

    This study reports a cost-effective method of replicating glass microfluidic chips using a vitreous carbon (VC) stamp. A glass replica with the required microfluidic microstructures was synthesized without etching. The replication method uses a VC stamp fabricated by combining thermal replication using a furan-based, thermally-curable polymer with carbonization. To test the feasibility of this method, a flow focusing droplet generator with flow-focusing and channel widths of 50 µm and 100 µm, respectively, was successfully fabricated in a soda-lime glass substrate. Deviation between the geometries of the initial shape and the vitreous carbon mold occurred because of shrinkage during the carbonization process, however this effect could be predicted and compensated for. Finally, the monodispersity of the droplets generated by the fabricated microfluidic device was evaluated. PMID:29286341

  10. Fabrication of Glass Microchannel via Glass Imprinting using a Vitreous Carbon Stamp for Flow Focusing Droplet Generator

    Directory of Open Access Journals (Sweden)

    Hyungjun Jang

    2017-12-01

    Full Text Available This study reports a cost-effective method of replicating glass microfluidic chips using a vitreous carbon (VC stamp. A glass replica with the required microfluidic microstructures was synthesized without etching. The replication method uses a VC stamp fabricated by combining thermal replication using a furan-based, thermally-curable polymer with carbonization. To test the feasibility of this method, a flow focusing droplet generator with flow-focusing and channel widths of 50 µm and 100 µm, respectively, was successfully fabricated in a soda-lime glass substrate. Deviation between the geometries of the initial shape and the vitreous carbon mold occurred because of shrinkage during the carbonization process, however this effect could be predicted and compensated for. Finally, the monodispersity of the droplets generated by the fabricated microfluidic device was evaluated.

  11. INCOMES AND WORKING TIMESUPPORT FOR QUALITY OF WORK AND EMPLOYMENT IN ROMANIA

    Directory of Open Access Journals (Sweden)

    Luminita CHIVU

    2007-12-01

    Full Text Available This paper contains a comparative analysis between living and working conditions in Romania and EU Member States, taking into account the differences between the existing regulations and the economic and social realities in these countries. Survey-based research on working conditions can prove valuable at a certain time if complemented with other data and facts regarding the particular socio-economic context and its changes in time. A strenght of the surveys is their ability to show that working conditions do not automatically improve as a result of the implementation of the acquis communautaire or following the improvement of labour market regulations. Besides, levels of income constitute one of the main reasons for dissatisfaction among Romanian workers.

  12. Remaining Useful Life Estimation using Time Trajectory Tracking and Support Vector Machines

    International Nuclear Information System (INIS)

    Galar, D; Kumar, U; Lee, J; Zhao, W

    2012-01-01

    In this paper, a novel RUL prediction method inspired by feature maps and SVM classifiers is proposed. The historical instances of a system with life-time condition data are used to create a classification by SVM hyper planes. For a test instance of the same system, whose RUL is to be estimated, degradation speed is evaluated by computing the minimal distance defined based on the degradation trajectories, i.e. the approach of the system to the hyper plane that segregates good and bad condition data at different time horizon. Therefore, the final RUL of a specific component can be estimated and global RUL information can then be obtained by aggregating the multiple RUL estimations using a density estimation method.

  13. Operating Security System Support for Run-Time Security with a Trusted Execution Environment

    DEFF Research Database (Denmark)

    Gonzalez, Javier

    Software services have become an integral part of our daily life. Cyber-attacks have thus become a problem of increasing importance not only for the IT industry, but for society at large. A way to contain cyber-attacks is to guarantee the integrity of IT systems at run-time. Put differently......, it is safe to assume that any complex software is compromised. The problem is then to monitor and contain it when it executes in order to protect sensitive data and other sensitive assets. To really have an impact, any solution to this problem should be integrated in commodity operating systems...... sensitive assets at run-time that we denote split-enforcement, and provide an implementation for ARM-powered devices using ARM TrustZone security extensions. We design, build, and evaluate a prototype Trusted Cell that provides trusted services. We also present the first generic TrustZone driver...

  14. Distributed Tactical Decision Support by Using Real-Time Database System

    Science.gov (United States)

    1987-11-01

    appendix A and detailed in depth in the Advanced Combat Direction System Specification (reference 5). The assumption is that ’ ime 0 (TO) of any contact...CONSTELLATION LAUNCH I F14A CAPM 330 350 10000 STOP At simulated engagement minute 30. the following orders are next submitted to the event generator...time of contact (ETC). There is the assumption in the ETC calculation that COURSE will change such that the new report would be on a dead- reckoning

  15. A Stitch in Time : Supporting Android Developers in Writing Secure Code

    OpenAIRE

    Nguyen, Duc Cuong; Wermke, Dominik; Acar, Yasemin; Backes, Michael; Weir, Charles Alexander Forbes; Fahl, Sascha

    2017-01-01

    Despite security advice in the official documentation and an extensive body of security research about vulnerabilities and exploits, many developers still fail to write secure Android applications. Frequently, Android developers fail to adhere to security best practices, leaving applications vulnerable to a multitude of attacks. We point out the advantage of a low-time-cost tool both to teach better secure coding and to improve app security. Using the FixDroid™ IDE plug-in, we show that profe...

  16. A personal tourism navigation system to support traveling multiple destinations with time restrictions

    OpenAIRE

    Maruyama, Atsushi; Shibata, Naoki; Murata, Yoshihiro; Yasumoto, Keiichi; Ito, Minoru

    2004-01-01

    We propose a personal navigation system (called PNS) which navigates a tourist through multiple destinations efficiently. In our PNS, a tourist can specify multiple destinations with desired arrival/stay time and preference degree. The system calculates the route including part of the destinations satisfying tourist's requirements and navigates him/her. For the above route search problem, we have developed an efficient route search algorithm using a genetic algorithm. We have designed and imp...

  17. Tourist Perceptions On Supporting Infrastructure Facilities And Climate-Based Visiting Time Of Ngebel Lake, Ponorogo

    Directory of Open Access Journals (Sweden)

    Ardhila Ayu Prasetyowati

    2014-04-01

    Full Text Available This study aims to analyze the tourists’ perception about the importance and satisfaction on the product of fisheries tourism, and to assess the visiting time of tourist based on climate conditions. The research was conducted in May to June 2013 in Ngebel Lake, Ponorogo. We used descriptive quantitative approach, with 45 respondents. Data collected from interview, questionnaire and observation. Analytical methods were used to determine the perception of tourists on the satisfaction and interest in fisheries tourism products, i.e. Importance Performance Analysis (IPA. We also used Tourism Climate Index (TCI to determine the visiting time of tourist. The results show the value of satisfaction and tourist interest is low, therefore the improvement of several aspects become important. It is encompasses: a the existence of parking area; b the condition of Ngebel Lake; c planning and management system, the condition of the local community; and d activities of fish course restaurant and fish farming system of floating net cages. TCI value indicates ideal conditions for tourists traveled in Ngebel Lake is in November (convenience index value of 106, in December (97 and in April (94. This appropriate time to visit Ngebel Lake is expected to create a good impression for the tourists and enjoy the various fisheries activities in Ngebel Lake. Keywords: Importance Performance Analysis, Ngebel Lake, Tourist Climate Index

  18. Real Time Space Weather Support for Chandra X-Ray Observatory Operations

    Science.gov (United States)

    O'Dell, Stephen L.; Minow, Joseph I.; Miller, J. Scott; Wolk, Scott J.; Aldcroft, Thomas L.; Spitzbart, Bradley D.; Swartz. Douglas A.

    2012-01-01

    NASA launched the Chandra X-ray Observatory in July 1999. Soon after first light in August 1999, however, degradation in the energy resolution and charge transfer efficiency of the Advanced CCD Imaging Spectrometer (ACIS) x-ray detectors was observed. The source of the degradation was quickly identified as radiation damage in the charge-transfer channel of the front-illuminated CCDs, by weakly penetrating ( soft , 100 500 keV) protons as Chandra passed through the Earth s radiation belts and ring currents. As soft protons were not considered a risk to spacecraft health before launch, the only on-board radiation monitoring system is the Electron, Proton, and Helium Instrument (EPHIN) which was included on Chandra with the primary purpose of monitoring energetic solar particle events. Further damage to the ACIS detector has been successfully mitigated through a combination of careful mission planning, autonomous on-board radiation protection, and manual intervention based upon real-time monitoring of the soft-proton environment. The AE-8 and AP-8 trapped radiation models and Chandra Radiation Models are used to schedule science operations in regions of low proton flux. EPHIN has been used as the primary autonomous in-situ radiation trigger; but, it is not sensitive to the soft protons that damage the front-illuminated CCDs. Monitoring of near-real-time space weather data sources provides critical information on the proton environment outside the Earth s magnetosphere due to solar proton events and other phenomena. The operations team uses data from the Geostationary Operational Environmental Satellites (GOES) to provide near-real-time monitoring of the proton environment; however, these data do not give a representative measure of the soft-proton (real-time data provided by NOAA s Space Weather Prediction Center. This presentation describes the radiation mitigation strategies to minimize the proton damage in the ACIS CCD detectors and the importance of real-time data

  19. Micro-patterned ZnO semiconductors for high performance thin film transistors via chemical imprinting with a PDMS stamp.

    Science.gov (United States)

    Seong, Kieun; Kim, Kyongjun; Park, Si Yun; Kim, Youn Sang

    2013-04-07

    Chemical imprinting was conducted on ZnO semiconductor films via a chemical reaction at the contact regions between a micro-patterned PDMS stamp and ZnO films. In addition, we applied the chemical imprinting on Li doped ZnO thin films for high performance TFTs fabrication. The representative micro-patterned Li doped ZnO TFTs showed a field effect mobility of 4.2 cm(2) V(-1) s(-1) after sintering at 300 °C.

  20. Influence of temperature and friction on the 22MnB5 formability under hot stamping conditions

    Science.gov (United States)

    Venturato, G.; Ghiotti, A.; Bruschi, S.

    2018-05-01

    The need to increase the safety and decrease the weight of the car body-in-white has determined the success of the direct hot stamping process as a primary technology for the automotive sector. Thanks to this process, parts with high strength-to-weight ratio can be obtained along with high stiffness and increase of the crashworthiness properties. Moreover, the thinner metal sheets used to manufacture the pieces lead to a decrease of the total weight of the car body-in-white, with a consequent reduction of the CO2 emissions. The direct hot stamping process is becoming the key to obtain pieces with high mechanical properties, thanks to the quenching stage that allows the manufacture of complex shapes characterized by a fully martensitic structure, thanks to the forming stage at elevated temperature and subsequent hardening inside the cooled dies. The aim of this paper is the investigation of the influence that the forming temperature may have on the formability of 22MnB5 steel sheets, commonly used in the hot stamping process of automotive components. Nakajima tests were carried out at different temperatures and the Forming Limit Diagrams (FLDs) at rupture were obtained and analysed. The temperature influenced both the major and the minor strain at which the sheet failed, indicating that not only the formability increased at increasing temperature, but there was also a modification of the strain path, which means a modification of the strain states through which the part passes during the deformation process. Moreover, the influence of friction is studied using a model developed in the LS-Dyna FEM environment. The obtained data are of great importance for an accurate calibration of Finite Element (FE) models of the hot stamping of real components in order to get optimal process parameters to obtain defects-free pieces.

  1. Experimental analysis of electro-pneumatic optimization of hot stamping machine control systems with on-delay timer

    OpenAIRE

    Bankole I. Oladapo; Vincent A. Balogun; Adeyinka O.M. Adeoye; Ige E. Olubunmi; Samuel O. Afolabi

    2017-01-01

    The sustainability criterion in the manufacturing industries is imperative, especially in the automobile industries. Currently, efforts are being made by the industries to mitigate CO2 emission by the total vehicle weight optimization, machine utilization and resource efficiency. In lieu of this, it is important to understudy the manufacturing machines adopted in the automobile industries. One of such machine is the hot stamping machine that is used for about 35% of the manufacturing operatio...

  2. Can Food Stamps Do More to Improve Food Choices? An Economic Perspective--Making Healthy Food Choices Easier: Ideas From Behavioral Economics

    OpenAIRE

    Mancino, Lisa; Andrews, Margaret S.

    2007-01-01

    With obesity the most prevalent nutrition problem facing Americans at all economic levels, promoting diets that provide adequate nutrition without too many calories has become an important objective for the Food Stamp Program. Findings from behavioral economics suggest innovative, low-cost ways to improve the diet quality of food stamp participants without restricting their freedom of choice. Unlike more traditional economic interventions, such as changing prices or banning specific foods, th...

  3. A decision support system for adaptive real-time management ofseasonal wetlands in California

    Energy Technology Data Exchange (ETDEWEB)

    Quinn, Nigel W.T.; Hanna, W. Mark

    2001-10-16

    This paper describes the development of a comprehensive flow and salinity monitoring system and application of a decision support system (DSS) to improve management of seasonal wetlands in the San Joaquin Valley of California. The Environmental Protection Agency regulates salinity discharges from non-point sources to the San Joaquin River using a procedure known as the Total Maximum Daily Load (TMDL) to allocate the assimilative capacity of the River for salt among watershed sources. Management of wetland sources of salt load will require the development of monitoring systems, more integrative management strategies and coordination with other entities. To obtain local cooperation the Grassland Water District, whose primary function is to supply surface water to private duck clubs and managed wetlands, needs to communicate to local landowners the likely impacts of salinity regulation on the long term health and function of wildfowl habitat. The project described in this paper will also provide this information. The models that form the backbone of the DSS develop salinity balances at both a regional and local scale. The regional scale concentrates on deliveries to and exports from the Grasland Water District while the local scale focuses on an individual wetland unit where more intensive monitoring is being conducted. The design of the DSS is constrained to meet the needs of busy wetland managers and is being designed from the bottom up utilizing tools and procedures familiar to these individuals.

  4. Time Synchronization Prototype, Server Upgrade Procedure Support and Remote Software Development

    Science.gov (United States)

    Sanders, Shania R.

    2014-01-01

    Networks are roadways of communication that connect devices. Like all roadways, there are rules and regulations that govern whatever (information in this case) travels along them. One type of rule that is commonly used is called a protocol. More specifically, a protocol is a standard that specifies how data should be transmitted over a network. The project outlined in this document seeks to implement one protocol in particular, Precision Time Protocol, within the Kennedy Ground Control Subsystem network at Kennedy Space Center. This document also summarizes work completed for server upgrades, remote software developer training and how all three assignments demonstrated the importance of accountability and security.

  5. A case of timely satellite image acquisitions in support of coastal emergency environmental response management

    Science.gov (United States)

    Ramsey, Elijah W.; Werle, Dirk; Lu, Zhong; Rangoonwala, Amina; Suzuoki, Yukihiro

    2009-01-01

    The synergistic application of optical and radar satellite imagery improves emergency response and advance coastal monitoring from the realm of “opportunistic” to that of “strategic.” As illustrated by the Hurricane Ike example, synthetic aperture radar imaging capabilities are clearly applicable for emergency response operations, but they are also relevant to emergency environmental management. Integrated with optical monitoring, the nearly real-time availability of synthetic aperture radar provides superior consistency in status and trends monitoring and enhanced information concerning causal forces of change that are critical to coastal resource sustainability, including flooding extent, depth, and frequency.

  6. Capillary-Force-Assisted Clean-Stamp Transfer of Two-Dimensional Materials.

    Science.gov (United States)

    Ma, Xuezhi; Liu, Qiushi; Xu, Da; Zhu, Yangzhi; Kim, Sanggon; Cui, Yongtao; Zhong, Lanlan; Liu, Ming

    2017-11-08

    A simple and clean method of transferring two-dimensional (2D) materials plays a critical role in the fabrication of 2D electronics, particularly the heterostructure devices based on the artificial vertical stacking of various 2D crystals. Currently, clean transfer techniques rely on sacrificial layers or bulky crystal flakes (e.g., hexagonal boron nitride) to pick up the 2D materials. Here, we develop a capillary-force-assisted clean-stamp technique that uses a thin layer of evaporative liquid (e.g., water) as an instant glue to increase the adhesion energy between 2D crystals and polydimethylsiloxane (PDMS) for the pick-up step. After the liquid evaporates, the adhesion energy decreases, and the 2D crystal can be released. The thin liquid layer is condensed to the PDMS surface from its vapor phase, which ensures the low contamination level on the 2D materials and largely remains their chemical and electrical properties. Using this method, we prepared graphene-based transistors with low charge-neutral concentration (3 × 10 10 cm -2 ) and high carrier mobility (up to 48 820 cm 2 V -1 s -1 at room temperature) and heterostructure optoelectronics with high operation speed. Finally, a capillary-force model is developed to explain the experiment.

  7. Mechanical Properties and Microstructure of High-Strength Steel Controlled by Hot Stamping Process

    Science.gov (United States)

    Ou, Hang; Zhang, Xu; Xu, Junrui; Li, Guangyao; Cui, Junjia

    2018-03-01

    A novel design and manufacturing method, dubbed "precast," of the cooling system and tools for a hot forming process was proposed in this paper. The integrated structures of the punch and blank holder were determined by analyzing the bending and reverse-bending deformation of the forming parts. The desired crashworthiness performance of an automotive front bumper constructed with this process was obtained by a tailored phase transformation, which generated martensite-bainite in the middle and full martensite transformation in the corner areas. Varying cooling effects in the formed parts caused the highest temperature to be located in the bottom and the lowest on the end of the formed parts. Moreover, the microstructural distributions demonstrated that the bottom possessed a relatively lower content of martensite, while, conversely, the end possessed a higher content. This was precisely the most desired phase distributions for the hot formed parts. For the six-process cycle stamping, the temperatures reached a stable status after an initial rapid increase in the first three process cycles. The microstructural results verified the feasibility of the hot forming tools under multiprocess cycles.

  8. The Effect of Process and Model Parameters in Temperature Prediction for Hot Stamping of Boron Steel

    Directory of Open Access Journals (Sweden)

    Chaoyang Sun

    2013-01-01

    Full Text Available Finite element models of the hot stamping and cold die quenching process for boron steel sheet were developed using either rigid or elastic tools. The effect of tool elasticity and process parameters on workpiece temperature was investigated. Heat transfer coefficient between blank and tools was modelled as a function of gap and contact pressure. Temperature distribution and thermal history in the blank were predicted, and thickness distribution of the blank was obtained. Tests were carried out and the test results are used for the validation of numerical predictions. The effect of holding load and the size of cooling ducts on temperature distribution during the forming and the cool die quenching process was also studied by using two models. The results show that higher accuracy predictions of blank thickness and temperature distribution during deformation were obtained using the elastic tool model. However, temperature results obtained using the rigid tool model were close to those using the elastic tool model for a range of holding load.

  9. Computationally determining the salience of decision points for real-time wayfinding support

    Directory of Open Access Journals (Sweden)

    Makoto Takemiya

    2012-06-01

    Full Text Available This study introduces the concept of computational salience to explain the discriminatory efficacy of decision points, which in turn may have applications to providing real-time assistance to users of navigational aids. This research compared algorithms for calculating the computational salience of decision points and validated the results via three methods: high-salience decision points were used to classify wayfinders; salience scores were used to weight a conditional probabilistic scoring function for real-time wayfinder performance classification; and salience scores were correlated with wayfinding-performance metrics. As an exploratory step to linking computational and cognitive salience, a photograph-recognition experiment was conducted. Results reveal a distinction between algorithms useful for determining computational and cognitive saliences. For computational salience, information about the structural integration of decision points is effective, while information about the probability of decision-point traversal shows promise for determining cognitive salience. Limitations from only using structural information and motivations for future work that include non-structural information are elicited.

  10. Operational Precipitation prediction in Support of Real-Time Flash Flood Prediction and Reservoir Management

    Science.gov (United States)

    Georgakakos, K. P.

    2006-05-01

    The presentation will outline the implementation and performance evaluation of a number of national and international projects pertaining to operational precipitation estimation and prediction in the context of hydrologic warning systems and reservoir management support. In all cases, uncertainty measures of the estimates and predictions are an integral part of the precipitation models. Outstanding research issues whose resolution is likely to lead to improvements in the operational environment are presented. The presentation draws from the experience of the Hydrologic Research Center (http://www.hrc-lab.org) prototype implementation projects at the Panama Canal, Central America, Northern California, and South-Central US. References: Carpenter, T.M, and K.P. Georgakakos, "Discretization Scale Dependencies of the Ensemble Flow Range versus Catchment Area Relationship in Distributed Hydrologic Modeling," Journal of Hydrology, 2006, in press. Carpenter, T.M., and K.P. Georgakakos, "Impacts of Parametric and Radar Rainfall Uncertainty on the Ensemble Streamflow Simulations of a Distributed Hydrologic Model," Journal of Hydrology, 298, 202-221, 2004. Georgakakos, K.P., Graham, N.E., Carpenter, T.M., Georgakakos, A.P., and H. Yao, "Integrating Climate- Hydrology Forecasts and Multi-Objective Reservoir Management in Northern California," EOS, 86(12), 122,127, 2005. Georgakakos, K.P., and J.A. Sperfslage, "Operational Rainfall and Flow Forecasting for the Panama Canal Watershed," in The Rio Chagres: A Multidisciplinary Profile of a Tropical Watershed, R.S. Harmon, ed., Kluwer Academic Publishers, The Netherlands, Chapter 16, 323-334, 2005. Georgakakos, K. P., "Analytical results for operational flash flood guidance," Journal of Hydrology, doi:10.1016/j.jhydrol.2005.05.009, 2005.

  11. Time domain models for damping-controlled fluidelastic instability forces in multi-span tubes with loose supports

    International Nuclear Information System (INIS)

    Hassan, M.A.; Rogers, R.J.; Gerber, A.G.

    2009-01-01

    This paper presents simulations of a loosely supported multi-span tube subjected to turbulence and fluidelastic instability forces. Several time-domain fluid force models simulating the damping controlled fluidelastic instability mechanism in tube arrays have been presented. These models include the negative damping model based on the Connors equation, fluid force coefficient-based models (Chen and Tanaka and Takahara), and two semi-analytical models (Price and Paidoussis; and Lever and Weaver) were implemented in an in-house finite code. Time domain modeling challenges for each of these theories were discussed. The implemented models were validated against available experimental data. The linear simulations showed that the Connors-equation based model exhibits the most conservative prediction of the critical flow velocity when the recommended design values for the Connors equation were used. The models were then utilized to simulate the nonlinear response of a three-span cantilever tube in a square lattice bar support subjected to air crossflow. The tube was subjected to a single-phase flow passing over one of the tube's spans. For each of these models the flow velocity and the support clearance were varied. Special attention was paid to the tube/support interaction parameters that affect wear, such as impact forces, contact ratio, and normal work rate. As the prediction of the linear threshold varies depending on the utilized model, the nonlinear response also differs. The investigated models exhibit similar response characteristics for the impact force, tip lift response, and work rate. Simulation results show that the Connors-based model underestimates the response and the tube/support interaction parameters for the loose support case. (author)

  12. Development of RODOS (Real-Time, On-Line Decision Support System), a comprehensive decision support system for nuclear emergencies in Europe - an overview

    International Nuclear Information System (INIS)

    Ehrhardt, J.; Paesler-Sauer, J.; Schuele, O.

    1993-01-01

    Within its Radiation Protection Research Programme, the Commission of the European Communities has embarked on a major project aiming at the development of an integrated and comprehensive real-time on-line decision support system (RODOS) for nuclear emergencies in Europe, applicable for the vicinity of the release and the early phase up to far distant areas and the later stages of an accident. At present, the project is organised as a joint venture of some 18 European institutes closely cooperating with several Russian and Ukrainian laboratories. The main purpose of the project is to provide the methodological basis, develop models and data and install the hardware and software framework of RODOS. The paper describes the key features, the overall design and the software structure broadly accepted by the contractors. The paper sketches the present status of RODOS and gives an overview of the important tasks of R and D work for the next project phases. (author)

  13. Operating Security System Support for Run-Time Security with a Trusted Execution Environment

    DEFF Research Database (Denmark)

    Gonzalez, Javier

    , it is safe to assume that any complex software is compromised. The problem is then to monitor and contain it when it executes in order to protect sensitive data and other sensitive assets. To really have an impact, any solution to this problem should be integrated in commodity operating systems...... in the Linux operating system. We are in the process of making this driver part of the mainline Linux kernel.......Software services have become an integral part of our daily life. Cyber-attacks have thus become a problem of increasing importance not only for the IT industry, but for society at large. A way to contain cyber-attacks is to guarantee the integrity of IT systems at run-time. Put differently...

  14. UNDERSTANDING THE SUBJECT´S BEHAVIOR IN THE INTERACTION WITH A DECISION SUPPORT SYSTEM UNDER TIME PRESSURE AND MISSING INFORMATION

    Directory of Open Access Journals (Sweden)

    Kathiane Benedetti Corso

    2011-12-01

    Full Text Available The article seeks to determine how time pressure and missing information in decision-making affect the behavior of decision makers. Data was collected through an experimental task of simulating the purchase of a car, which was structured with the AHP (Analytic Hierarchy Process multi-criteria method in a Decision Support System. When pressured by time, the experimental subjects focused on the car of their choice; whereas with no time pressure, some of them rationalized more, used the information, and did not agree with the chosen car. Assumptions of the Theory of Image justified some findings, indicating that previously structured images in the mind of the decision maker are a way to cope with time pressure. Given the missing information, the use of background knowledge and individual experience were the most prominent coping strategy.

  15. A webgis supported snow information system with long time satellite data for Turkey

    Science.gov (United States)

    Surer, S.; Bolat, K.; Akyurek, Z.

    2012-04-01

    products have been produced for around 12 years from 2000 to 2012 and it is being produced daily as the data is available. 72% overall accuracy was obtained from the validation analysis. Our website will be available to give service to our users to make analysis on snow extent with a long time series database for free. By the help of WEBGIS interface it is going to be possible to produce time series of snow cover areas, and produce graphs and summary statistics for a better management of information on snow cover in various fields from flood forecast integration, energy production planning of hydropower plants which are fed from snow melting, and producing input for climate models.

  16. Just-in-Time Adaptive Interventions (JITAIs) in Mobile Health: Key Components and Design Principles for Ongoing Health Behavior Support.

    Science.gov (United States)

    Nahum-Shani, Inbal; Smith, Shawna N; Spring, Bonnie J; Collins, Linda M; Witkiewitz, Katie; Tewari, Ambuj; Murphy, Susan A

    2018-05-18

    The just-in-time adaptive intervention (JITAI) is an intervention design aiming to provide the right type/amount of support, at the right time, by adapting to an individual's changing internal and contextual state. The availability of increasingly powerful mobile and sensing technologies underpins the use of JITAIs to support health behavior, as in such a setting an individual's state can change rapidly, unexpectedly, and in his/her natural environment. Despite the increasing use and appeal of JITAIs, a major gap exists between the growing technological capabilities for delivering JITAIs and research on the development and evaluation of these interventions. Many JITAIs have been developed with minimal use of empirical evidence, theory, or accepted treatment guidelines. Here, we take an essential first step towards bridging this gap. Building on health behavior theories and the extant literature on JITAIs, we clarify the scientific motivation for JITAIs, define their fundamental components, and highlight design principles related to these components. Examples of JITAIs from various domains of health behavior research are used for illustration. As we enter a new era of technological capacity for delivering JITAIs, it is critical that researchers develop sophisticated and nuanced health behavior theories capable of guiding the construction of such interventions. Particular attention has to be given to better understanding the implications of providing timely and ecologically sound support for intervention adherence and retention.

  17. SOIL MOISTURE SPACE-TIME ANALYSIS TO SUPPORT IMPROVED CROP MANAGEMENT

    Directory of Open Access Journals (Sweden)

    Bruno Montoani Silva

    2015-02-01

    Full Text Available The knowledge of the water content in the soil profile is essential for an efficient management of crop growth and development. This work aimed to use geostatistical techniques in a spatio-temporal study of soil moisture in an Oxisol in order to provide that information for improved crop management. Data were collected in a coffee crop area at São Roque de Minas, in the upper São Francisco River basin, MG state, Brazil. The soil moisture was measured with a multi-sensor capacitance (MCP probe at 10-, 20-, 30-, 40-, 60- and 100-cm depths between March and December, 2010. After adjusting the spherical semivariogram model using ordinary least squares, best model, the values were interpolated by kriging in order to have a continuous surface relating depth x time (CSDT and the soil water availability to plant (SWAP. The results allowed additional insight on the dynamics of soil water and its availability to plant, and pointed to the effects of climate on the soil water content. These results also allowed identifying when and where there was greater water consumption by the plants, and the soil layers where water was available and potentially explored by the plant root system.

  18. Time Domain Response Analysis of Barge Floater Supporting an Offshore Wind Turbine

    Directory of Open Access Journals (Sweden)

    A.C. Mayilvahanan

    2011-12-01

    Full Text Available Wind energy is a reliable source of sustainable power generation and has been an active area of research globally to economically harness the energy for human use. Reliable source of wind energy pushed the engineers to install wind turbines near and far off the coasts. In shallow water upto 100 m, fixed structures like tripods, jackets, monopiles and gravity base are functionally and economically feasible. In deep waters, a floating substructure can be more economical for offshore wind turbine. In this study a barge type floater of different aspect ratios from 0.4 to 1.0 is investigated for its performance under wave and wind loading. All these floaters were designed with a defined transverse metacentric height (GM equal to 1.0 m and the hydrodynamic analysis is carried out using WAMIT. The barge with aspect ratio B/L = 1.0 is found to have lowest pitch RAO. The time domain surge, heave and pitch response for this barge has been obtained using Integro-differential equation of motion and the statistical response characteristics are compared for two different cases of excitation namely, wave excitation alone and combined wave and wind excitation. Statistics of surge, heave and pitch responses are obtained for three different seas states and for two different wave heading angles.

  19. Real-Time PCR Quantification of Chloroplast DNA Supports DNA Barcoding of Plant Species.

    Science.gov (United States)

    Kikkawa, Hitomi S; Tsuge, Kouichiro; Sugita, Ritsuko

    2016-03-01

    Species identification from extracted DNA is sometimes needed for botanical samples. DNA quantification is required for an accurate and effective examination. If a quantitative assay provides unreliable estimates, a higher quantity of DNA than the estimated amount may be used in additional analyses to avoid failure to analyze samples from which extracting DNA is difficult. Compared with conventional methods, real-time quantitative PCR (qPCR) requires a low amount of DNA and enables quantification of dilute DNA solutions accurately. The aim of this study was to develop a qPCR assay for quantification of chloroplast DNA from taxonomically diverse plant species. An absolute quantification method was developed using primers targeting the ribulose-1,5-bisphosphate carboxylase/oxygenase large subunit (rbcL) gene using SYBR Green I-based qPCR. The calibration curve was generated using the PCR amplicon as the template. DNA extracts from representatives of 13 plant families common in Japan. This demonstrates that qPCR analysis is an effective method for quantification of DNA from plant samples. The results of qPCR assist in the decision-making will determine the success or failure of DNA analysis, indicating the possibility of optimization of the procedure for downstream reactions.

  20. A real-time neutron-gamma discriminator based on the support vector machine method for the time-of-flight neutron spectrometer

    Science.gov (United States)

    Wei, ZHANG; Tongyu, WU; Bowen, ZHENG; Shiping, LI; Yipo, ZHANG; Zejie, YIN

    2018-04-01

    A new neutron-gamma discriminator based on the support vector machine (SVM) method is proposed to improve the performance of the time-of-flight neutron spectrometer. The neutron detector is an EJ-299-33 plastic scintillator with pulse-shape discrimination (PSD) property. The SVM algorithm is implemented in field programmable gate array (FPGA) to carry out the real-time sifting of neutrons in neutron-gamma mixed radiation fields. This study compares the ability of the pulse gradient analysis method and the SVM method. The results show that this SVM discriminator can provide a better discrimination accuracy of 99.1%. The accuracy and performance of the SVM discriminator based on FPGA have been evaluated in the experiments. It can get a figure of merit of 1.30.

  1. Atmospheric dispersion models for real-time application in the decision support system being developed within the CEC

    International Nuclear Information System (INIS)

    Mikkelsen, T.

    1992-01-01

    A number of Commission of the European Communities member states are presently coordinating their research and development of a ''Real-time On-line DecisiOn Support'' (RODOS) for emergency assistance in the event of nuclear accident. In addition to atmospheric dispersion, the system involves multiple other radiological disciplines. The ability to estimate a specific atmospheric dispersion scenarios in real-time becomes a first-priority task and is of uttermost importance for the subsequent success or failure of such a comprehensive decision support system to guide off-site emergency situations. No single dispersion model is at present able to cover all possible release-types and scales of dispersion. A hierarchy of atmospheric flow and dispersion models is presently being ranked for suitability to real-time calculate air and integrated-air concentrations. Starting at the short-range scale, models are discriminated with respect to principle, adequacy and flexibility, CPU-time constraints, experimental evaluation record, instantaneous or short-time release handling, deposition measures (wet and dry), input and output data flexibility and uncertainty-handling and model-interpretation. Additional features of particular importance are: Robustness in schemes for meteorological preprocessing of meteorological input data, and on-line backfitting and data-assimilation procedures. Models demonstrating practical and operational use, including real-time operational experience, have in this context the highest priority, as opposed to the more sophisticated and theoretical ''development-type'' models. Real-time methods founded on our present knowledge and data concerning flow and dispersion in the atmospheric boundary layer, are of primary interest. (au) (18 refs.)

  2. Retention of Basic Life Support in Laypeople: Mastery Learning vs. Time-based Education.

    Science.gov (United States)

    Boet, Sylvain; Bould, M Dylan; Pigford, Ashlee-Ann; Rössler, Bernhard; Nambyiah, Pratheeban; Li, Qi; Bunting, Alexandra; Schebesta, Karl

    2017-01-01

    To compare the effectiveness of a mastery learning (ML) versus a time-based (TB) BLS course for the acquisition and retention of BLS knowledge and skills in laypeople. After ethics approval, laypeople were randomized to a ML or TB BLS course based on the American Heart Association (AHA) Heartsaver course. In the ML group, subjects practiced and received feedback at six BLS stations until they reached a pre-determined level of performance. The TB group received a standard AHA six-station BLS course. All participants took the standard in-course BLS skills test at the end of their course. BLS skills and knowledge were tested using a high-fidelity scenario and knowledge questionnaire upon course completion (immediate post-test) and after four months (retention test). Video recorded scenarios were assessed by two blinded, independent raters using the AHA skills checklist. Forty-three subjects were included in analysis (23ML;20TB). For primary outcome, subjects' performance did not change after four months, regardless of the teaching modality (TB from (median[IQR]) 8.0[6.125;8.375] to 8.5[5.625;9.0] vs. ML from 8.0[7.0;9.0] to 7.0[6.0;8.0], p = 0.12 for test phase, p = 0.21 for interaction between effect of teaching modality and test phase). For secondary outcomes, subjects acquired knowledge between pre- and immediate post-tests (p < 0.005), and partially retained the acquired knowledge up to four months (p < 0.005) despite a decrease between immediate post-test and retention test (p = 0.009), irrespectively of the group (p = 0.59) (TB from 63.3[48.3;73.3] to 93.3[81.7;100.0] and then 93.3[81.7;93.3] vs. ML from 60.0[46.7;66.7] to 93.3[80.0;100.0] and then 80.0[73.3;93.3]). Regardless of the group after 4 months, chest compression depth improved (TB from 39.0[35.0;46.0] to 48.5[40.25;58.0] vs. ML from 40.0[37.0;47.0] to 45.0[37.0;52.0]; p = 0.012), but not the rate (TB from 118.0[114.0;125.0] to 120.5[113.0;129.5] vs. ML from 119.0[113.0;130.0] to 123.0[102.0;132.0]; p

  3. The Value of Caregiver Time: Costs of Support and Care for Individuals Living with Autism Spectrum Disorder

    Directory of Open Access Journals (Sweden)

    Carolyn Dudley

    2014-01-01

    Full Text Available When a child is diagnosed with autism spectrum disorder, the significance of the impact that diagnosis can have on his or her family’s life is incalculable, except in one respect: cost. If that child is severely impacted and requires constant and lifelong supports, then the value of caregiver time required to support that individual is approximately $5.5 million higher than that for someone without autism. An autism diagnosis of a high-needs child at age two represents the equivalent of telling the family that they must make an immediate lump-sum investment on that day of $1.6 million, invested at a five-per-cent return, to pay for the lifetime costs of care and support their loved one will require. And that amount does not even account for added professional services, such as speech therapists, psychologists, and occupational therapists, or additional out-of-pocket expenses that may be required, such as special equipment or diets. Autism is the most common neurological condition diagnosed in children and it is now estimated that one in 88 children will be diagnosed with autism spectrum disorders. Yet, across Canada, there are significant gaps in the publicly provided support system, leaving the cost burden to be picked up by families. In the case of those individuals requiring constant support, 24 hours a day, every day, the cost of hiring caregivers alone would require an annual income of $200,000 — before a family even begins to pay for shelter, clothing, groceries and other basic necessities. Already families with severe high-needs children are more likely to experience lower income than they might otherwise, due to the extra care commitment their loved one requires. Only a very few families will have the means to afford to pay for total care. So, in most cases, the responsibility for care falls largely, if not entirely, on the family, or in a worst-case scenario, the autistic individual is left with inadequate care. Autism is an

  4. Collection of human reaction times and supporting health related data for analysis of cognitive and physical performance

    Directory of Open Access Journals (Sweden)

    Petr Brůha

    2018-04-01

    Full Text Available Smoking, excessive drinking, overeating and physical inactivity are well-established risk factors decreasing human physical performance. Moreover, epidemiological work has identified modifiable lifestyle factors, such as poor diet and physical and cognitive inactivity that are associated with the risk of reduced cognitive performance. Definition, collection and annotation of human reaction times and suitable health related data and metadata provides researchers with a necessary source for further analysis of human physical and cognitive performance. The collection of human reaction times and supporting health related data was obtained from two groups comprising together 349 people of all ages - the visitors of the Days of Science and Technology 2016 held on the Pilsen central square and members of the Mensa Czech Republic visiting the neuroinformatics lab at the University of West Bohemia. Each provided dataset contains a complete or partial set of data obtained from the following measurements: hands and legs reaction times, color vision, spirometry, electrocardiography, blood pressure, blood glucose, body proportions and flexibility. It also provides a sufficient set of metadata (age, gender and summary of the participant's current life style and health to allow researchers to perform further analysis. This article has two main aims. The first aim is to provide a well annotated collection of human reaction times and health related data that is suitable for further analysis of lifestyle and human cognitive and physical performance. This data collection is complemented with a preliminarily statistical evaluation. The second aim is to present a procedure of efficient acquisition of human reaction times and supporting health related data in non-lab and lab conditions. Keywords: Reaction time, Health related data, Cognitive and physical performance, Chronic disease, Data acquisition, Data collection, Software for data collection

  5. Helium-hydrogen microplasma device (MPD) on postage-stamp-size plastic-quartz chips.

    Science.gov (United States)

    Weagant, Scott; Karanassios, Vassili

    2009-10-01

    A new design of a miniaturized, atmospheric-pressure, low-power (e.g., battery-operated), self-igniting, planar-geometry microplasma device (MPD) for use with liquid microsamples is described. The inexpensive MPD was a hybrid, three-substrate quartz-plastic-plastic structure and it was formed on chips with area the size of a small postage stamp. The substrates were chosen for rapid prototyping and for speedy device-geometry testing and evaluation. The approximately 700-microm (diameter) and 7-mm (long) He-H(2) (3% H(2)) microplasma was formed by applying high-voltage ac between two needle electrodes. Operating conditions were found to be critical in sustaining stable microplasma on plastic substrates. Spectral interference from the electrode materials was not observed. A small-size, electrothermal vaporization system was used for introduction of microliter volumes of liquids into the MPD. The microplasma was operated from an inexpensive power supply. And, operation from a 14.4-V battery has been demonstrated. Microplasma background emission in the spectral range between 200 and 850 nm obtained using a portable, fiber-optic spectrometer is reported. Analyte emission from microliter volumes of dilute single-element standard solutions of Cd, Cu, K, Li, Mg, Mn, Na, Pb, and Zn is documented. Element-dependent precision was between 10-25% (the average was 15%) and detection limits ranged between 1.5 and 350 ng. The system was used for the determination of Na in diluted bottled-water samples.

  6. Associations of food stamp participation with dietary quality and obesity in children.

    Science.gov (United States)

    Leung, Cindy W; Blumenthal, Susan J; Hoffnagle, Elena E; Jensen, Helen H; Foerster, Susan B; Nestle, Marion; Cheung, Lilian W Y; Mozaffarian, Dariush; Willett, Walter C

    2013-03-01

    To determine if obesity and dietary quality in low-income children differed by participation in the Supplemental Nutrition Assistance Program (SNAP), formerly the Food Stamp Program. The study population included 5193 children aged 4 to 19 with household incomes ≤130% of the federal poverty level from the 1999-2008 NHANES. Diet was measured by using 24-hour recalls. Among low-income US children, 28% resided in households currently receiving SNAP benefits. After adjusting for sociodemographic differences, SNAP participation was not associated with a higher rate of childhood obesity (odds ratio = 1.11, 95% confidence interval [CI]: 0.71-1.74). Both SNAP participants and low-income nonparticipants were below national recommendations for whole grains, fruits, vegetables, fish, and potassium, while exceeding recommended limits for processed meat, sugar-sweetened beverages, saturated fat, and sodium. Zero percent of low-income children met at least 7 of 10 dietary recommendations. After multivariate adjustment, compared with nonparticipants, SNAP participants consumed 43% more sugar-sweetened beverages (95% CI: 8%-89%), 47% more high-fat dairy (95% CI: 7%, 101%), and 44% more processed meats (95% CI: 9%-91%), but 19% fewer nuts, seeds, and legumes (95% CI: -35% to 0%). In part due to these differences, intakes of calcium, iron, and folate were significantly higher among SNAP participants. Significant differences by SNAP participation were not evident in total energy, macronutrients, Healthy Eating Index 2005 scores, or Alternate Healthy Eating Index scores. The diets of low-income children are far from meeting national dietary recommendations. Policy changes should be considered to restructure SNAP to improve children's health.

  7. Development of the Real Time Situation Identification Model for Adaptive Service Support in Vehicular Communication Networks Domain

    Directory of Open Access Journals (Sweden)

    Mindaugas Kurmis

    2013-01-01

    Full Text Available The article discusses analyses and assesses the key proposals how to deal with the situation identification for the heterogeneous service support in vehicular cooperation environment. This is one of the most important topics of the pervasive computing. Without the solution it is impossible to adequately respond to the user's needs and to provide needed services in the right place at the right moment and in the right way. In this work we present our developed real time situation identification model for adaptive service support in vehicular communication networks domain. Our solution is different from the others as it uses additional virtual context information source - information from other vehicles which for our knowledge is not addressed in the past. The simulation results show the promising context exchange rate between vehicles. The other vehicles provided additional context source in our developed model helps to increase situations identification level.

  8. Effect of Al-Si Coating on Weld Microstructure and Properties of 22MnB5 Steel Joints for Hot Stamping

    Science.gov (United States)

    Lin, Wenhu; Li, Fang; Wu, Dongsheng; Chen, Xiaoguan; Hua, Xueming; Pan, Hua

    2018-03-01

    22MnB5 hot stamping steels are gradually being used in tailor-welded blank applications. In this experiment, 1-mm-thick Al-Si coated and de-coated 22MnB5 steels were laser-welded and then hot-stamped. The chemical compositions, solidification process, microstructure and mechanical properties were investigated to reveal the effect of Al-Si coating and heat treatment. In the welded condition, the coated joints had an Al content of approximately 2.5 wt.% in the fusion zone and the de-coated joints had 0.5 wt.% Al. The aluminum promoted the δ-ferrite formation as the skeletal structure during solidification. In the high-aluminum weld, the microstructure consisted of martensite and long and band-like δ-ferrite. Meanwhile, the low-aluminum weld was full of lath martensite. After the hot stamping process, the δ-ferrite fraction increased from 10 to 24% in the coated joints and the lath martensite became finer in the de-coated joints. The tensile strengths of the coated joints or de-coated joints were similar to that before hot stamping, but the strength of the coated joints was reduced heavily after hot stamping compared to the de-coated joints and base material. The effect of δ-ferrite on the tensile properties became stronger when the fusion zone was soft and deformed first in the hot-stamped specimens. The coated weld showed a brittle fracture surface with many cleavage planes, and the de-coated weld showed a ductile fracture surface with many dimples in hot-stamped conditions.

  9. A novel self-supporting GEM-based amplification structure for a time projection chamber at the ILC

    Energy Technology Data Exchange (ETDEWEB)

    Behnke, Ties; Diener, Ralf; Rosemann, Christoph; Steder, Lea

    2012-11-15

    In this paper, a new self-supporting way to mount Gas Electron Multipliers is presented. It has been developed to provide a method to cover large readout areas while ensuring the flatness of the foils and keeping the amount of dead material minimal. The structure has been tested in a Time Projection Chamber prototype, using cosmic muon tracks. The impact of the mounting structure on the track reconstruction and the single point resolution is quantified and its impact on the tracking efficiency and dE/dx measurements is estimated.

  10. All-fiber incoherent frequency-to-time mapping method for microwave signal generation with baseband transmission and multicasting support

    DEFF Research Database (Denmark)

    Company Torres, Victor; Tafur Monroy, Idelfonso; Lancis, Jesus

    2008-01-01

    We present a proof-of-principle experiment for achieving simultaneous distribution of baseband radio-frequency data and up-conversion with broadcasting support over a passive optical network. The technique is based on an incoherent frequency-to-time mapping method for pulse shaping. Specifically...... resembles the shape of the incoherent source. The photodetected signal contains both the baseband data and an up-frequency converted copy with central wavelength for the microwave carrier into the ultra-wideband range and tuning capability by selection of the fiber length. (c) 2008 Elsevier B.V. All rights...

  11. Systematic review of peer support for breastfeeding continuation: metaregression analysis of the effect of setting, intensity, and timing.

    Science.gov (United States)

    Jolly, Kate; Ingram, Lucy; Khan, Khalid S; Deeks, Jonathan J; Freemantle, Nick; MacArthur, Christine

    2012-01-25

    To examine the effect of setting, intensity, and timing of peer support on breast feeding. Systematic review and metaregression analysis of randomised controlled trials. Cochrane Library, Medline, CINAHL, the National Research Register, and British Nursing Index were searched from inception or from 1980 to 2011. Review methods Study selection, data abstraction, and quality assessment were carried out independently and in duplicate. Risk ratios and 95% confidence intervals were calculated for individual studies and pooled. Effects were estimated for studies grouped according to setting (high income countries, low or middle income countries, and the United Kingdom), intensity (services in high income countries need to undergo concurrent evaluation.

  12. On the Use of Time-Limited Information for Maintenance Decision Support: A Predictive Approach under Maintenance Constraints

    Directory of Open Access Journals (Sweden)

    E. Khoury

    2013-01-01

    Full Text Available This paper deals with a gradually deteriorating system operating under an uncertain environment whose state is only known on a finite rolling horizon. As such, the system is subject to constraints. Maintenance actions can only be planned at imposed times called maintenance opportunities that are available on a limited visibility horizon. This system can, for example, be a commercial vehicle with a monitored critical component that can be maintained only in some specific workshops. Based on the considered system, we aim to use the monitoring data and the time-limited information for maintenance decision support in order to reduce its costs. We propose two predictive maintenance policies based, respectively, on cost and reliability criteria. Classical age-based and condition-based policies are considered as benchmarks. The performance assessment shows the value of the different types of information and the best way to use them in maintenance decision making.

  13. Participatory Research to Design a Novel Telehealth System to Support the Night-Time Needs of People with Dementia: NOCTURNAL

    Directory of Open Access Journals (Sweden)

    Suzanne Martin

    2013-12-01

    Full Text Available Strategies to support people living with dementia are broad in scope, proposing both pharmacological and non-pharmacological interventions as part of the care pathway. Assistive technologies form part of this offering as both stand-alone devices to support particular tasks and the more complex offering of the “smart home” to underpin ambient assisted living. This paper presents a technology-based system, which expands on the smart home architecture, orientated to support people with daily living. The system, NOCTURNAL, was developed by working directly with people who had dementia, and their carers using qualitative research methods. The research focused primarily on the nighttime needs of people living with dementia in real home settings. Eight people with dementia had the final prototype system installed for a three month evaluation at home. Disturbed sleep patterns, night-time wandering were a focus of this research not only in terms of detection by commercially available technology but also exploring if automated music, light and visual personalized photographs would be soothing to participants during the hours of darkness. The NOCTURNAL platform and associated services was informed by strong user engagement of people with dementia and the service providers who care for them. NOCTURNAL emerged as a holistic service offering a personalised therapeutic aspect with interactive capabilities.

  14. Participatory research to design a novel telehealth system to support the night-time needs of people with dementia: NOCTURNAL.

    Science.gov (United States)

    Martin, Suzanne; Augusto, Juan Carlos; McCullagh, Paul; Carswell, William; Zheng, Huiru; Wang, Haiying; Wallace, Jonathan; Mulvenna, Maurice

    2013-12-04

    Strategies to support people living with dementia are broad in scope, proposing both pharmacological and non-pharmacological interventions as part of the care pathway. Assistive technologies form part of this offering as both stand-alone devices to support particular tasks and the more complex offering of the "smart home" to underpin ambient assisted living. This paper presents a technology-based system, which expands on the smart home architecture, orientated to support people with daily living. The system, NOCTURNAL, was developed by working directly with people who had dementia, and their carers using qualitative research methods. The research focused primarily on the nighttime needs of people living with dementia in real home settings. Eight people with dementia had the final prototype system installed for a three month evaluation at home. Disturbed sleep patterns, night-time wandering were a focus of this research not only in terms of detection by commercially available technology but also exploring if automated music, light and visual personalized photographs would be soothing to participants during the hours of darkness. The NOCTURNAL platform and associated services was informed by strong user engagement of people with dementia and the service providers who care for them. NOCTURNAL emerged as a holistic service offering a personalised therapeutic aspect with interactive capabilities.

  15. New technique for laryngotracheal mucosa transplantation. 'Stamp' welding using indocyanine green dye and albumin interaction with diode laser.

    Science.gov (United States)

    Wang, Z; Pankratov, M M; Gleich, L L; Rebeiz, E E; Shapshay, S M

    1995-07-01

    To investigate (1) the possibility of survival of free mucosa "stamp" grafts fixed in the airway with a new technique using indocyanine green-dyed albumin solder activated with a diode laser and (2) the degree of improvement of wound healing in the airway by applying modified microskin transplantation techniques from burn surgery to cover a relatively large wound with a few small pieces of mucosa anchored in place with the previously mentioned technique. Three (one control and two experimental) rectangular (10 x 8 mm) wounds in tracheal mucosa were produced in four experimental animals (dogs) using a carbon dioxide laser. The control wound was left uncovered. In the first experimental wound, a mucosal flap was raised and then fixed in place by a trapdoor flap method. In the second experimental wound, two small (each 2 x 3 mm) autogenous mucosa grafts were anchored onto the surface with indocyanine green-dyed albumin activated with an 810-nm diode laser. Histomorphologically, the postoperative results from three wounds were compared. The experimental wounds were completely covered by regenerated squamous cells in 1 week and by ciliated epithelium in 2 weeks after the operation despite the discrepancy in size of the graft to wound area (1:6.7) covered with the stamp mucosa. No thermal damage from the diode laser was noted in the second experimental wounds. In the control wounds, no coverage was observed at 1 week, and only squamous cells were noted 2 weeks postoperatively. All the wounds had normal ciliated epithelium coverage at 4 weeks. Transplanted stamp grafts provided similar or better healing than trapdoor flap transplants. This new technique made endoscopic mucosal grafting possible and offers a potential breakthrough in the management of laryngotracheal stenosis.

  16. Gear fault diagnosis under variable conditions with intrinsic time-scale decomposition-singular value decomposition and support vector machine

    Energy Technology Data Exchange (ETDEWEB)

    Xing, Zhanqiang; Qu, Jianfeng; Chai, Yi; Tang, Qiu; Zhou, Yuming [Chongqing University, Chongqing (China)

    2017-02-15

    The gear vibration signal is nonlinear and non-stationary, gear fault diagnosis under variable conditions has always been unsatisfactory. To solve this problem, an intelligent fault diagnosis method based on Intrinsic time-scale decomposition (ITD)-Singular value decomposition (SVD) and Support vector machine (SVM) is proposed in this paper. The ITD method is adopted to decompose the vibration signal of gearbox into several Proper rotation components (PRCs). Subsequently, the singular value decomposition is proposed to obtain the singular value vectors of the proper rotation components and improve the robustness of feature extraction under variable conditions. Finally, the Support vector machine is applied to classify the fault type of gear. According to the experimental results, the performance of ITD-SVD exceeds those of the time-frequency analysis methods with EMD and WPT combined with SVD for feature extraction, and the classifier of SVM outperforms those for K-nearest neighbors (K-NN) and Back propagation (BP). Moreover, the proposed approach can accurately diagnose and identify different fault types of gear under variable conditions.

  17. Anesthesia information management system-based near real-time decision support to manage intraoperative hypotension and hypertension.

    Science.gov (United States)

    Nair, Bala G; Horibe, Mayumi; Newman, Shu-Fang; Wu, Wei-Ying; Peterson, Gene N; Schwid, Howard A

    2014-01-01

    Intraoperative hypotension and hypertension are associated with adverse clinical outcomes and morbidity. Clinical decision support mediated through an anesthesia information management system (AIMS) has been shown to improve quality of care. We hypothesized that an AIMS-based clinical decision support system could be used to improve management of intraoperative hypotension and hypertension. A near real-time AIMS-based decision support module, Smart Anesthesia Manager (SAM), was used to detect selected scenarios contributing to hypotension and hypertension. Specifically, hypotension (systolic blood pressure 1.25 minimum alveolar concentration [MAC]) of inhaled drug and hypertension (systolic blood pressure >160 mm Hg) with concurrent phenylephrine infusion were detected, and anesthesia providers were notified via "pop-up" computer screen messages. AIMS data were retrospectively analyzed to evaluate the effect of SAM notification messages on hypotensive and hypertensive episodes. For anesthetic cases 12 months before (N = 16913) and after (N = 17132) institution of SAM messages, the median duration of hypotensive episodes with concurrent high MAC decreased with notifications (Mann Whitney rank sum test, P = 0.031). However, the reduction in the median duration of hypertensive episodes with concurrent phenylephrine infusion was not significant (P = 0.47). The frequency of prolonged episodes that lasted >6 minutes (sampling period of SAM), represented in terms of the number of cases with episodes per 100 surgical cases (or percentage occurrence), declined with notifications for both hypotension with >1.25 MAC inhaled drug episodes (δ = -0.26% [confidence interval, -0.38% to -0.11%], P 1.25 MAC inhaled drug episodes. However, since phenylephrine infusion is manually documented in an AIMS, the impact of notification messages was less pronounced in reducing episodes of hypertension with concurrent phenylephrine infusion. Automated data capture and a higher frequency of

  18. Real-time RT-PCR, a necessary tool to support the diagnosis and surveillance of rotavirus in Mexico.

    Science.gov (United States)

    De La Cruz Hernández, Sergio Isaac; Anaya Molina, Yazmin; Gómez Santiago, Fabián; Terán Vega, Heidi Lizbeth; Monroy Leyva, Elda; Méndez Pérez, Héctor; García Lozano, Herlinda

    2018-04-01

    Rotavirus produces diarrhea in children under 5 years old. Most of those conventional methods such as polyacrylamide gel electrophoresis (PAGE) and reverse transcription-polymerase chain reaction (RT-PCR) have been used for rotavirus detection. However, these techniques need a multi-step process to get the results. In comparison with conventional methods, the real-time RT-PCR is a highly sensitive method, which allows getting the results in only one day. In this study a real-time RT-PCR assay was tested using a panel of 440 samples from patients with acute gastroenteritis, and characterized by PAGE and RT-PCR. The results show that the real-time RT-PCR detected rotavirus from 73% of rotavirus-negative samples analyzed by PAGE and RT-PCR; thus, the percentage of rotavirus-positive samples increased to 81%. The results indicate that this real-time RT-PCR should be part of a routine analysis, and as a support of the diagnosis of rotavirus in Mexico. Copyright © 2017 Elsevier Inc. All rights reserved.

  19. Associations between Parental and Friend Social Support and Children’s Physical Activity and Time Spent outside Playing

    Directory of Open Access Journals (Sweden)

    Constantinos A. Loucaides

    2017-01-01

    Full Text Available The purpose of this study was to examine the structural validity of a parent and a child questionnaire that assessed parental and friends’ influences on children’s physical activity and investigate the associations between the derived factors, physical activity, and time spent outside. Children (N=154, mean age = 11.7 and 144 of their parents completed questionnaires assessing parental and friends’ influences on children’s physical activity. Children wore a pedometer for six days. Exploratory factor analyses revealed four factors for the parental and five for the child’s questionnaire that explained 66.71% and 63.85% of the variance, respectively. Five factors were significantly associated with physical activity and five significantly associated with time spent outside. Higher correlations were revealed between “general friend support,” “friends’ activity norms,” and physical activity (r=0.343 and 0.333 resp., p<0.001 and between “general friend support” and time spent outside (r=0.460, p<0.001. Obtaining information relating to parental and friends’ influences on physical activity from both parents and children may provide a more complete picture of influences. Parents and friends seem to influence children’s physical activity behavior and time spent outside, but friends’ influences may have a stronger impact on children’s behaviors.

  20. The reduction of irregularities in the use of “process fmea”: a study for a cold stamping process

    Directory of Open Access Journals (Sweden)

    Carla Estorilio

    2011-12-01

    Full Text Available The Failure Mode and Effect Analysis (FMEA is a requirement for ISO/TS 16949. However, researches show nonconformities in its use by automotive suppliers. The objective of this study is to identify these nonconformities, aiming to suggest methods for minimizing this problem. Therefore, questionnaires were applied in seven automotive suppliers and, for each one, ten FMEA`s were analysed. The research identified nonconformities in the use of FMEA for the stamping process and highlighted seven influencing factors. Based on this data, a strategy is suggested. A partially parameterised FMEA spreadsheet is suggested and tested in three suppliers, showing significant improvements.

  1. The effects of scaffolding in the classroom : support contingency and student independent working time in relation to student achievement, task effort and appreciation of support

    NARCIS (Netherlands)

    van de Pol, Janneke; Volman, Monique; Oort, Frans; Beishuizen, Jos

    2015-01-01

    Teacher scaffolding, in which teachers support students adaptively or contingently, is assumed to be effective. Yet, hardly any evidence from classroom studies exists. With the current experimental classroom study we investigated whether scaffolding affects students’ achievement, task effort, and

  2. Failure prognostics by support vector regression of time series data under stationary/nonstationary environmental and operational conditions

    International Nuclear Information System (INIS)

    Liu, Jie

    2015-01-01

    This Ph. D. work is motivated by the possibility of monitoring the conditions of components of energy systems for their extended and safe use, under proper practice of operation and adequate policies of maintenance. The aim is to develop a Support Vector Regression (SVR)-based framework for predicting time series data under stationary/nonstationary environmental and operational conditions. Single SVR and SVR-based ensemble approaches are developed to tackle the prediction problem based on both small and large datasets. Strategies are proposed for adaptively updating the single SVR and SVR-based ensemble models in the existence of pattern drifts. Comparisons with other online learning approaches for kernel-based modelling are provided with reference to time series data from a critical component in Nuclear Power Plants (NPPs) provided by Electricite de France (EDF). The results show that the proposed approaches achieve comparable prediction results, considering the Mean Squared Error (MSE) and Mean Relative Error (MRE), in much less computation time. Furthermore, by analyzing the geometrical meaning of the Feature Vector Selection (FVS) method proposed in the literature, a novel geometrically interpretable kernel method, named Reduced Rank Kernel Ridge Regression-II (RRKRR-II), is proposed to describe the linear relations between a predicted value and the predicted values of the Feature Vectors (FVs) selected by FVS. Comparisons with several kernel methods on a number of public datasets prove the good prediction accuracy and the easy-of-tuning of the hyper-parameters of RRKRR-II. (author)

  3. Later school start times for supporting the education, health, and well-being of high school students.

    Science.gov (United States)

    Marx, Robert; Tanner-Smith, Emily E; Davison, Colleen M; Ufholz, Lee-Anne; Freeman, John; Shankar, Ravi; Newton, Lisa; Brown, Robert S; Parpia, Alyssa S; Cozma, Ioana; Hendrikx, Shawn

    2017-07-03

    A number of school systems worldwide have proposed and implemented later school start times as a means of avoiding the potentially negative impacts that early morning schedules can have on adolescent students. Even mild sleep deprivation has been associated with significant health and educational concerns: increased risk for accidents and injuries, impaired learning, aggression, memory loss, poor self-esteem, and changes in metabolism. Although researchers have begun to explore the effects of delayed school start time, no one has conducted a rigorous review of evidence to determine whether later school start times support adolescent health, education, and well-being. We aimed to assess the effects of a later school start time for supporting health, education, and well-being in high school students.Secondary objectives were to explore possible differential effects of later school start times in student subgroups and in different types of schools; to identify implementation practices, contextual factors, and delivery modes associated with positive and negative effects of later start times; and to assess the effects of later school start times on the broader community (high school faculty and staff, neighborhood, and families). We conducted the main search for this review on 28 October 2014 and updated it on 8 February 2016. We searched CENTRAL as well as 17 key electronic databases (including MEDLINE, Embase, ERIC, PsycINFO, and Sociological Abstracts), current editions of relevant journals and organizational websites, trial registries, and Google Scholar. We included any randomized controlled trials, controlled before-and-after studies, and interrupted time series studies with sufficient data points that pertained to students aged 13 to 19 years and that compared different school start times. Studies that reported either primary outcomes of interest (academic outcomes, amount or quality of sleep, mental health indicators, attendance, or alertness) or secondary

  4. Disruption of Ttll5/stamp gene (tubulin tyrosine ligase-like protein 5/SRC-1 and TIF2-associated modulatory protein gene) in male mice causes sperm malformation and infertility.

    Science.gov (United States)

    Lee, Geun-Shik; He, Yuanzheng; Dougherty, Edward J; Jimenez-Movilla, Maria; Avella, Matteo; Grullon, Sean; Sharlin, David S; Guo, Chunhua; Blackford, John A; Awasthi, Smita; Zhang, Zhenhuan; Armstrong, Stephen P; London, Edra C; Chen, Weiping; Dean, Jurrien; Simons, S Stoney

    2013-05-24

    TTLL5/STAMP (tubulin tyrosine ligase-like family member 5) has multiple activities in cells. TTLL5 is one of 13 TTLLs, has polyglutamylation activity, augments the activity of p160 coactivators (SRC-1 and TIF2) in glucocorticoid receptor-regulated gene induction and repression, and displays steroid-independent growth activity with several cell types. To examine TTLL5/STAMP functions in whole animals, mice were prepared with an internal deletion that eliminated several activities of the Stamp gene. This mutation causes both reduced levels of STAMP mRNA and C-terminal truncation of STAMP protein. Homozygous targeted mutant (Stamp(tm/tm)) mice appear normal except for marked decreases in male fertility associated with defects in progressive sperm motility. Abnormal axonemal structures with loss of tubulin doublets occur in most Stamp(tm/tm) sperm tails in conjunction with substantial reduction in α-tubulin polyglutamylation, which closely correlates with the reduction in mutant STAMP mRNA. The axonemes in other structures appear unaffected. There is no obvious change in the organs for sperm development of WT versus Stamp(tm/tm) males despite the levels of WT STAMP mRNA in testes being 20-fold higher than in any other organ examined. This defect in male fertility is unrelated to other Ttll genes or 24 genes previously identified as important for sperm function. Thus, STAMP appears to participate in a unique, tissue-selective TTLL-mediated pathway for α-tubulin polyglutamylation that is required for sperm maturation and motility and may be relevant for male fertility.

  5. The Relationships of Self-Esteem, Future Time Perspective, Positive Affect, Social Support, and Career Decision: A Longitudinal Multilevel Study

    Science.gov (United States)

    Park, In-Jo; Kim, Minhee; Kwon, Seungwoo; Lee, Hae-Gyoung

    2018-01-01

    This study aimed, first, to determine whether the intra-individual variability in positive affect was related to the intra-individual variability in career decision-making self-efficacy, and career choice anxiety. The second objective was to examine whether social support moderates the relationship between affect and these outcome variables. The third objective was to find out how career decision-making self-efficacy and career choice anxiety change according to self-esteem and future time perspective. We conducted a study using the daily diary method in which participants were asked to rate their affect or attitudes for 21 consecutive days. In total, 128 university students participated in this study. The main results were as follows. First, positive affect was associated positively with career decision-making self-efficacy and negatively with career choice anxiety. Second, social support had a synergy effect with positive affect to influence career choice anxiety. Third, self-esteem was related positively to career decision-making self-efficacy and negatively to career choice anxiety. We discuss theoretical and practical implications. PMID:29755381

  6. The Relationships of Self-Esteem, Future Time Perspective, Positive Affect, Social Support, and Career Decision: A Longitudinal Multilevel Study.

    Science.gov (United States)

    Park, In-Jo; Kim, Minhee; Kwon, Seungwoo; Lee, Hae-Gyoung

    2018-01-01

    This study aimed, first, to determine whether the intra-individual variability in positive affect was related to the intra-individual variability in career decision-making self-efficacy, and career choice anxiety. The second objective was to examine whether social support moderates the relationship between affect and these outcome variables. The third objective was to find out how career decision-making self-efficacy and career choice anxiety change according to self-esteem and future time perspective. We conducted a study using the daily diary method in which participants were asked to rate their affect or attitudes for 21 consecutive days. In total, 128 university students participated in this study. The main results were as follows. First, positive affect was associated positively with career decision-making self-efficacy and negatively with career choice anxiety. Second, social support had a synergy effect with positive affect to influence career choice anxiety. Third, self-esteem was related positively to career decision-making self-efficacy and negatively to career choice anxiety. We discuss theoretical and practical implications.

  7. The Relationships of Self-Esteem, Future Time Perspective, Positive Affect, Social Support, and Career Decision: A Longitudinal Multilevel Study

    Directory of Open Access Journals (Sweden)

    In-Jo Park

    2018-04-01

    Full Text Available This study aimed, first, to determine whether the intra-individual variability in positive affect was related to the intra-individual variability in career decision-making self-efficacy, and career choice anxiety. The second objective was to examine whether social support moderates the relationship between affect and these outcome variables. The third objective was to find out how career decision-making self-efficacy and career choice anxiety change according to self-esteem and future time perspective. We conducted a study using the daily diary method in which participants were asked to rate their affect or attitudes for 21 consecutive days. In total, 128 university students participated in this study. The main results were as follows. First, positive affect was associated positively with career decision-making self-efficacy and negatively with career choice anxiety. Second, social support had a synergy effect with positive affect to influence career choice anxiety. Third, self-esteem was related positively to career decision-making self-efficacy and negatively to career choice anxiety. We discuss theoretical and practical implications.

  8. The real-time on-line decision support system RODOS for off-site emergency management

    International Nuclear Information System (INIS)

    Benz, G.; Ehrhardt, J.; Faude, D.; Fischer, F.; Paesler-Sauer, J.; Rafat, M.; Schichtel, T.; Schuele, O.; Steinhauer, C.

    1994-01-01

    The project RODOS aims at the development of an integrated and comprehensive real-time on-line decision support system for off-site emergency management of nuclear accidents in Europe, applicable to the vicinity of the accident and its early phase up to far distant areas and later stages. As a joint venture of 18 institutions in the European Union, in close cooperation with institutions in Russia, Belarus, Ukraine and east-central Europe, the project is to provide the methodological basis, develop models, collect data, and install the hardware and software framework of the RODOS system. The paper describes the project status, the overall design of the system and its present software structure, and gives a brief overview of important research and development tasks for the next project phases. (orig.) [de

  9. DCDS: A Real-time Data Capture and Personalized Decision Support System for Heart Failure Patients in Skilled Nursing Facilities.

    Science.gov (United States)

    Zhu, Wei; Luo, Lingyun; Jain, Tarun; Boxer, Rebecca S; Cui, Licong; Zhang, Guo-Qiang

    2016-01-01

    Heart disease is the leading cause of death in the United States. Heart failure disease management can improve health outcomes for elderly community dwelling patients with heart failure. This paper describes DCDS, a real-time data capture and personalized decision support system for a Randomized Controlled Trial Investigating the Effect of a Heart Failure Disease Management Program (HF-DMP) in Skilled Nursing Facilities (SNF). SNF is a study funded by the NIH National Heart, Lung, and Blood Institute (NHLBI). The HF-DMP involves proactive weekly monitoring, evaluation, and management, following National HF Guidelines. DCDS collects a wide variety of data including 7 elements considered standard of care for patients with heart failure: documentation of left ventricular function, tracking of weight and symptoms, medication titration, discharge instructions, 7 day follow up appointment post SNF discharge and patient education. We present the design and implementation of DCDS and describe our preliminary testing results.

  10. Radar Waveform Recognition Based on Time-Frequency Analysis and Artificial Bee Colony-Support Vector Machine

    Directory of Open Access Journals (Sweden)

    Lutao Liu

    2018-04-01

    Full Text Available In this paper, a system for identifying eight kinds of radar waveforms is explored. The waveforms are the binary phase shift keying (BPSK, Costas codes, linear frequency modulation (LFM and polyphase codes (including P1, P2, P3, P4 and Frank codes. The features of power spectral density (PSD, moments and cumulants, instantaneous properties and time-frequency analysis are extracted from the waveforms and three new features are proposed. The classifier is support vector machine (SVM, which is optimized by artificial bee colony (ABC algorithm. The system shows well robustness, excellent computational complexity and high recognition rate under low signal-to-noise ratio (SNR situation. The simulation results indicate that the overall recognition rate is 92% when SNR is −4 dB.

  11. Electric Load Forecasting Based on a Least Squares Support Vector Machine with Fuzzy Time Series and Global Harmony Search Algorithm

    Directory of Open Access Journals (Sweden)

    Yan Hong Chen

    2016-01-01

    Full Text Available This paper proposes a new electric load forecasting model by hybridizing the fuzzy time series (FTS and global harmony search algorithm (GHSA with least squares support vector machines (LSSVM, namely GHSA-FTS-LSSVM model. Firstly, the fuzzy c-means clustering (FCS algorithm is used to calculate the clustering center of each cluster. Secondly, the LSSVM is applied to model the resultant series, which is optimized by GHSA. Finally, a real-world example is adopted to test the performance of the proposed model. In this investigation, the proposed model is verified using experimental datasets from the Guangdong Province Industrial Development Database, and results are compared against autoregressive integrated moving average (ARIMA model and other algorithms hybridized with LSSVM including genetic algorithm (GA, particle swarm optimization (PSO, harmony search, and so on. The forecasting results indicate that the proposed GHSA-FTS-LSSVM model effectively generates more accurate predictive results.

  12. The role in supporting activities of the public health nurses at the time of a radiation disaster

    International Nuclear Information System (INIS)

    Okuda, Hiroko; Kunugita, Naoki; Miyata, Ryouko

    2013-01-01

    After The Great East Japan Earthquake in March 2011, the great disaster not only was a seismic hazard but also influenced health anxiety by the radiation in the nuclear power plant. The residents who lived in this area have been faced with strict dangerous circumstances still now. So this research is to clarify the substance of supporting activities of the public health nurses of a local government after a nuclear power plant disaster. Group interviews were conducted with public health nurses who were engaged in Fukushima nuclear power plant disaster experiences. The numbers of the public health nurses were 11 (3 belonged to prefecture governments, 8 belonged to local governments). Their mean tenure as a public health nurse was 30.7±3.0 years. They didn't have any training opportunity to get technical knowledge of the nuclear power plant disaster, so that they couldn't cope with the anxiety of the residents after the disaster. Therefore, it is necessary to improve 'the fundamental knowledge of radiation', 'a care of the heart', 'risk communication', 'organizations-concerned cooperation' and 'organization maintenance at the time of usual circumstances'. We found that the local governments which have a nuclear power plant institution have not been trained enough at the time of usual business, nor maintenance of operations required for accident preparedness, either. It was showed that from now on, the education for public health nurses is emergently required to cope with a radiation disaster, including a fundamental knowledge of radiation and resident support services from local governments regardless of whether their prefecture has a nuclear power plant or not. (author)

  13. Event for the launch of the Georges Charpak postage stamp | 26-27 February | Prévessin site

    CERN Multimedia

    2016-01-01

    At the end of February, the French post office is releasing a new €0.70 stamp featuring an image of Georges Charpak. CERN is taking part in this event by hosting a temporary post office on the Prévessin site, which will sell the stamp with a special “first day” postmark before it goes on general sale.     Georges Charpak arrived at CERN in 1959 and, in the late 1960s, revolutionised particle detection technology by developing the multiwire proportional chamber. This technique brought particle detectors into the electronic era, setting physicists free from the laborious task of studying photographs one by one. In 1992, he was awarded the Nobel Prize in Physics for his invention. Charpak chambers are still used today in the LHC detectors and have paved the way for the technology in numerous other modern detectors. In the 1990s, Charpak was involved in developing medical applications based on particle detection technology. He was als...

  14. Assembly of live micro-organisms on microstructured PDMS stamps by convective/capillary deposition for AFM bio-experiments

    International Nuclear Information System (INIS)

    Dague, E; Jauvert, E; Laplatine, L; Thibault, C; Viallet, B; Ressier, L

    2011-01-01

    Immobilization of live micro-organisms on solid substrates is an important prerequisite for atomic force microscopy (AFM) bio-experiments. The method employed must immobilize the cells firmly enough to enable them to withstand the lateral friction forces exerted by the tip during scanning but without denaturing the cell interface. In this work, a generic method for the assembly of living cells on specific areas of substrates is proposed. It consists in assembling the living cells within the patterns of microstructured, functionalized poly-dimethylsiloxane (PDMS) stamps using convective/capillary deposition. This versatile approach is validated by applying it to two systems of foremost importance in biotechnology and medicine: Saccharomyces cerevisiae yeasts and Aspergillus fumigatus fungal spores. We show that this method allows multiplexing AFM nanomechanical measurements by force spectroscopy on S. cerevisiae yeasts and high-resolution AFM imaging of germinated Aspergillus conidia in buffer medium. These two examples clearly demonstrate the immense potential of micro-organism assembly on functionalized, microstructured PDMS stamps by convective/capillary deposition for performing rigorous AFM bio-experiments on living cells.

  15. Experimental study on the warm forming and quenching behavior for hot stamping of high-strength aluminum alloys

    Science.gov (United States)

    Degner, J.; Horn, A.; Merklein, M.

    2017-09-01

    Within the last decades, stringent regulations on fuel consumption, CO2 emissions and product recyclability forced the automotive sector to implement new strategies within the field of car body manufacturing. Due to their low density and good corrosion resistance, aluminum became one of the most relevant lightweight materials. Recently, especially high- strength aluminum alloys for structural components gained importance. Since the low formability of these alloys limits their application, there is a need for novel process strategies in order to enhance the forming behavior. One promising approach is the hot stamping of aluminum alloys. The combination of quenching and forming in one step after solution heat treatment leads to a significant improvement of the formability. Furthermore, higher manufacturing accuracy can be achieved due to reduced spring back. Within this contribution, the influence of forming temperature on the subsequent material behavior and the heat transfer during quenching will be analyzed. Therefore, the mechanical and thermal material characteristics such as flow behavior and heat transfer coefficient during hot stamping are investigated.

  16. Investigation into the Fiber Orientation Effect on the Formability of GLARE Materials in the Stamp Forming Process

    Science.gov (United States)

    Liu, Shichen; Lang, Lihui; Sherkatghanad, Ehsan; Wang, Yao; Xu, Wencai

    2018-04-01

    Glass-reinforced aluminum laminate (GLARE) is a new class of fiber metal laminates (FMLs) which has the advantages such as high tensile strength, outstanding fatigue, impact resistance, and excellent corrosion properties. GLARE has been extensively applied in advanced aerospace and automobile industries. However, the deformation behavior of the glass fiber during forming must be studied to the benefits of the good-quality part we form. In this research, we focus on the effect of fiber layer orientation on the GLARE laminate formability in stamp forming process. Experimental and numerical analysis of stamping a hemisphere part in different fiber orientation is investigated. The results indicate that unidirectional and multi-directional fiber in the middle layer make a significant effect on the thinning and also surface forming quality of the three layer sheet. Furthermore, the stress-strain distribution of the aluminum alloy and the unique anisotropic property of the fiber layer exhibit that fiber layer orientation can also affect the forming depths as well as the fracture modes of the laminate. According to the obtained results, it is revealed that multi-directional fiber layers are a good alternative compared to the unidirectional fibers especially when a better formability is the purpose.

  17. Integrating support vector machines and random forests to classify crops in time series of Worldview-2 images

    Science.gov (United States)

    Zafari, A.; Zurita-Milla, R.; Izquierdo-Verdiguier, E.

    2017-10-01

    Crop maps are essential inputs for the agricultural planning done at various governmental and agribusinesses agencies. Remote sensing offers timely and costs efficient technologies to identify and map crop types over large areas. Among the plethora of classification methods, Support Vector Machine (SVM) and Random Forest (RF) are widely used because of their proven performance. In this work, we study the synergic use of both methods by introducing a random forest kernel (RFK) in an SVM classifier. A time series of multispectral WorldView-2 images acquired over Mali (West Africa) in 2014 was used to develop our case study. Ground truth containing five common crop classes (cotton, maize, millet, peanut, and sorghum) were collected at 45 farms and used to train and test the classifiers. An SVM with the standard Radial Basis Function (RBF) kernel, a RF, and an SVM-RFK were trained and tested over 10 random training and test subsets generated from the ground data. Results show that the newly proposed SVM-RFK classifier can compete with both RF and SVM-RBF. The overall accuracies based on the spectral bands only are of 83, 82 and 83% respectively. Adding vegetation indices to the analysis result in the classification accuracy of 82, 81 and 84% for SVM-RFK, RF, and SVM-RBF respectively. Overall, it can be observed that the newly tested RFK can compete with SVM-RBF and RF classifiers in terms of classification accuracy.

  18. Comparison of random forests and support vector machine for real-time radar-derived rainfall forecasting

    Science.gov (United States)

    Yu, Pao-Shan; Yang, Tao-Chang; Chen, Szu-Yin; Kuo, Chen-Min; Tseng, Hung-Wei

    2017-09-01

    This study aims to compare two machine learning techniques, random forests (RF) and support vector machine (SVM), for real-time radar-derived rainfall forecasting. The real-time radar-derived rainfall forecasting models use the present grid-based radar-derived rainfall as the output variable and use antecedent grid-based radar-derived rainfall, grid position (longitude and latitude) and elevation as the input variables to forecast 1- to 3-h ahead rainfalls for all grids in a catchment. Grid-based radar-derived rainfalls of six typhoon events during 2012-2015 in three reservoir catchments of Taiwan are collected for model training and verifying. Two kinds of forecasting models are constructed and compared, which are single-mode forecasting model (SMFM) and multiple-mode forecasting model (MMFM) based on RF and SVM. The SMFM uses the same model for 1- to 3-h ahead rainfall forecasting; the MMFM uses three different models for 1- to 3-h ahead forecasting. According to forecasting performances, it reveals that the SMFMs give better performances than MMFMs and both SVM-based and RF-based SMFMs show satisfactory performances for 1-h ahead forecasting. However, for 2- and 3-h ahead forecasting, it is found that the RF-based SMFM underestimates the observed radar-derived rainfalls in most cases and the SVM-based SMFM can give better performances than RF-based SMFM.

  19. Elevated-temperature tests of simply-supported beams and circular plates subjected to time-varying loadings

    International Nuclear Information System (INIS)

    Corum, J.M.; Richardson, M.

    1975-01-01

    The measured elastic-plastic and elastic-plastic-creep responses of a number of simply-supported type 304 stainless steel beams and circular plates are presented. Beams and plates exhibit the essential features of inelastic structural behavior; yet they are relatively simple. In beams, the stress fields are largely uniaxial, while multiaxial effects are introduced in plates. The specimens were laterally loaded at the center, and the tests were performed by subjecting the specimens to either a prescribed load or center-deflection history. The specimens were machined from a common, well-characterized heat of material, and all of the tests were performed at a temperature of 1100 F. The elastic-plastic tests consisted of short-time cycling of the center load, or deflection, between fixed limits. In the elastic-plastic-creep tests the center load, or deflection, was held constant for periods of time, but was periodically subjected to a step increase or decrease, including reversals. The test results are presented in terms of the load and center-deflection behaviors, which typify the overall structural behavior. (U.S.)

  20. Real-Time Very High-Resolution Regional 4D Assimilation in Supporting CRYSTAL-FACE Experiment

    Science.gov (United States)

    Wang, Donghai; Minnis, Patrick

    2004-01-01

    To better understand tropical cirrus cloud physical properties and formation processes with a view toward the successful modeling of the Earth's climate, the CRYSTAL-FACE (Cirrus Regional Study of Tropical Anvils and Cirrus Layers - Florida Area Cirrus Experiment) field experiment took place over southern Florida from 1 July to 29 July 2002. During the entire field campaign, a very high-resolution numerical weather prediction (NWP) and assimilation system was performed in support of the mission with supercomputing resources provided by NASA Center for Computational Sciences (NCCS). By using NOAA NCEP Eta forecast for boundary conditions and as a first guess for initial conditions assimilated with all available observations, two nested 15/3 km grids are employed over the CRYSTAL-FACE experiment area. The 15-km grid covers the southeast US domain, and is run two times daily for a 36-hour forecast starting at 0000 UTC and 1200 UTC. The nested 3-km grid covering only southern Florida is used for 9-hour and 18-hour forecasts starting at 1500 and 0600 UTC, respectively. The forecasting system provided more accurate and higher spatial and temporal resolution forecasts of 4-D atmospheric fields over the experiment area than available from standard weather forecast models. These forecasts were essential for flight planning during both the afternoon prior to a flight day and the morning of a flight day. The forecasts were used to help decide takeoff times and the most optimal flight areas for accomplishing the mission objectives. See more detailed products on the web site http://asd-www.larc.nasa.gov/mode/crystal. The model/assimilation output gridded data are archived on the NASA Center for Computational Sciences (NCCS) UniTree system in the HDF format at 30-min intervals for real-time forecasts or 5-min intervals for the post-mission case studies. Particularly, the data set includes the 3-D cloud fields (cloud liquid water, rain water, cloud ice, snow and graupe/hail).