Effect of Metal (Mn, Ti Doping on NCA Cathode Materials for Lithium Ion Batteries

Directory of Open Access Journals (Sweden)

Dao Yong Wan

2018-01-01

Full Text Available NCA (LiNi0.85Co0.10Al0.05-x MxO2, M=Mn or Ti, x < 0.01 cathode materials are prepared by a hydrothermal reaction at 170°C and doped with Mn and Ti to improve their electrochemical properties. The crystalline phases and morphologies of various NCA cathode materials are characterized by XRD, FE-SEM, and particle size distribution analysis. The CV, EIS, and galvanostatic charge/discharge test are employed to determine the electrochemical properties of the cathode materials. Mn and Ti doping resulted in cell volume expansion. This larger volume also improved the electrochemical properties of the cathode materials because Mn4+ and Ti4+ were introduced into the octahedral lattice space occupied by the Li-ions to expand the Li layer spacing and, thereby, improved the lithium diffusion kinetics. As a result, the NCA-Ti electrode exhibited superior performance with a high discharge capacity of 179.6 mAh g−1 after the first cycle, almost 23 mAh g−1 higher than that obtained with the undoped NCA electrode, and 166.7 mAh g−1 after 30 cycles. A good coulombic efficiency of 88.6% for the NCA-Ti electrode is observed based on calculations in the first charge and discharge capacities. In addition, the NCA-Ti cathode material exhibited the best cycling stability of 93% up to 30 cycles.

Toxicological aspects of photocatalytic degradation of selected xenobiotics with nano-sized Mn-doped TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Ozmen, Murat, E-mail: murat.ozmen@inonu.edu.tr [Inonu University, Faculty of Science, Department of Biology, Malatya (Turkey); Güngördü, Abbas [Inonu University, Faculty of Science, Department of Biology, Malatya (Turkey); Erdemoglu, Sema [Inonu University, Faculty of Science, Department of Chemistry, Malatya (Turkey); Ozmen, Nesrin [Inonu University, Faculty of Education, Department of Science Teaching Program, Malatya (Turkey); Asilturk, Meltem [Akdeniz University, Department of Materials Science and Engineering, Antalya (Turkey)

2015-08-15

Highlights: • Undoped and Mn-doped TiO{sub 2} nanoparticles were synthesized and characterized. • The photocatalytic efficiency of the photocatalysts was evaluated for BPA and ATZ. • Toxicity of photocatalysts and photocatalytic by-products were determined. • Mn-doped TiO{sub 2} nanoparticles did not cause significant lethality on X. laevis. • Degradation of BPA caused a significant reduction of lethal effects. - Abstract: The toxic effects of two selected xenobiotics, bisphenol A (BPA) and atrazine (ATZ), were evaluated after photocatalytic degradation using nano-sized, Mn-doped TiO{sub 2}. Undoped and Mn-doped TiO{sub 2} nanoparticles were synthesized. The samples were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), UV–vis-diffuse reflectance spectra (DRS), X-ray fluorescence spectroscopy (XRF), and BET surface area. The photocatalytic efficiency of the undoped and Mn-doped TiO{sub 2} was evaluated for BPA and ATZ. The toxicity of the synthesized photocatalysts and photocatalytic by-products of BPA and ATZ was determined using frog embryos and tadpoles, zebrafish embryos, and bioluminescent bacteria. Possible toxic effects were also evaluated using selected enzyme biomarkers. The results showed that Mn-doped TiO{sub 2} nanoparticles did not cause significant lethality in Xenopus laevis embryos and tadpoles, but nonfiltered samples caused lethality in zebrafish. Furthermore, Mn-doping of TiO{sub 2} increased the photocatalytic degradation capability of nanoparticles, and it successfully degraded BPA and AZT, but degradation of AZT caused an increase of the lethal effects on both tadpoles and fish embryos. Degradation of BPA caused a significant reduction of lethal effects, especially after 2–4 h of degradation. However, biochemical assays showed that both Mn-doped TiO{sub 2} and the degradation by-products caused a significant change of selected biomarkers on X. laevis tadpoles; thus, the ecological risks of Mn

Effect of calcination temperature on structural properties and photocatalytic activity of Mn-C-codoped TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Cai, Jianbo; Xin, Wei; Liu, Guanglong; Lin, Die; Zhu, Duanwei, E-mail: liugl@mail.hzau.edu.cn [Laboratory of Eco-Environmental Engineering Research, College of Resources and Environment, Huazhong Agricultural University (HZAU), Wuhan (China)

2016-03-15

Mn-C-codoped TiO{sub 2} catalysts were synthesized by modified sol-gel method based on the self-assembly technique using polyoxyethylene sorbitan monooleate (Tween 80) as template and carbon precursor and the effect of calcination temperature on their structural properties and photocatalytic activity were investigated. The XRD results showed undoped and Mn-C-codoped TiO{sub 2} calcined at 400 deg C only include anatase phase and the rutile phase appears when the calcination temperature reached to 600 deg C. UV-vis absorption spectroscopy demonstrates that the absorption spectra are strongly modified by the calcination temperature. Moreover, the Mn-C-TiO{sub 2} calcined at 400 deg C showed the lowest PL intensity due to a decrease in the recombination rate of photogenerated electrons and holes under light irradiation. The photocatalytic activity of Mn-C-codoped TiO{sub 2} were evaluated by the degradation of methyl orange (MO) under the simulate daylight irradiation and all the prepared Mn-C-codoped TiO{sub 2} samples exhibited high photocatalytic activities for photocatalytic decolorisation of methyl orange aqueous solution. At 400 deg C, the Mn-C-codoped TiO{sub 2} samples showed the highest photocatalytic activity due to synergetic effects of good crystallize ation, appropriate phase composition and slower recombination rate of photogenerated charge carriers, which further confirms the calcination temperature could affect the properties of Mn-C-codoped TiO2 significantly. (author)

Photoelectrochemical performance of Mn-TiO{sub 2} thin films mounted on FTO prepared by sol-gel spin coating

Energy Technology Data Exchange (ETDEWEB)

Chen, J.C.; Song, G.H. [National Central Univ., Taoyuan, Taiwan (China). Dept. of Mechanical Engineering; Lu, C.W. [Jen-Teh Junior College, Hou- Lung, Taiwan (China). Dept. of Information Management; Tseng, C.J. [National Central Univ., Chung-Li, Taoyuan County, Taiwan (China). Dept. of Mechanical Engineering; Cheng, K.W. [Chang Gung Univ., Tao-Yuan, Taiwan (China). Dept. of Chemical and Materials Engineering

2009-07-01

Tin oxide (TiO{sub 2}) sol-gels with Mn{sup 2+} molar ratios ranging from 0 to 0.1 per cent were used to form nano-structured Mn(x)Ti(1-x)O(2) thin films. A layer-by-layer spincoating (LLSC) technique was used, in which 10 very thin and uniform coating layers of Mn(x)Ti(1-x)O(2) were deposited on fluorine doped tin oxide (FTO) glass. Properties of the thin films were determined as a function of annealing temperature and molar ratio of the Mn{sup 2+} ions by X-ray diffraction (XRD), scanning electron microscopy (SEM), Atomic Force microscopy (AFM) and photoelectrochemical (PEC) measurements. The PEC measurements were obtained in a dry-type three-electrode cell consisting of sample, platinized and reference Ag/AgCl electrodes. The results revealed that the Mn(x)Ti(1-x)O(2) thin films have better structure and electrochemical characteristics when the annealing temperature is 550 degrees C. The TiO{sub 2} thin films with Mn{sup 2+} ions also had higher photocurrent than undoped TiO{sub 2}. The optimum Mn{sup 2+} loading in this study was found to be 0.1 ml per cent. The maximum photocurrent of Mn(0.1)Ti(0.9)O(2) thin films is about 0.68 mA/cm2 when the bias potential is 0.8 V (vs.Ag/AgCl).

Spin-polarized electron gas in Co2MSi/SrTiO3(M= Ti, V, Cr, Mn, and Fe) heterostructures

KAUST Repository

Nazir, S.; Schwingenschlö gl, Udo

2016-01-01

Spin-polarized density functional theory is used to study the TiO2 terminated interfaces between the magnetic Heusler alloys Co2Si (M = Ti, V, Cr, Mn, and Fe) and the non-polar band insulator SrTiO3. The structural relaxation at the interface turns

Above room temperature ferromagnetism in Si:Mn and TiO(2-delta)Co.

Science.gov (United States)

Granovsky, A; Orlov, A; Perov, N; Gan'shina, E; Semisalova, A; Balagurov, L; Kulemanov, I; Sapelkin, A; Rogalev, A; Smekhova, A

2012-09-01

We present recent experimental results on the structural, electrical, magnetic, and magneto-optical properties of Mn-implanted Si and Co-doped TiO(2-delta) magnetic oxides. Si wafers, both n- and p-type, with high and low resistivity, were used as the starting materials for implantation with Mn ions at the fluencies up to 5 x 10(16) cm(-2). The saturation magnetization was found to show the lack of any regular dependence on the Si conductivity type, type of impurity and the short post-implantation annealing. According to XMCD Mn impurity in Si does not bear any appreciable magnetic moment at room temperature. The obtained results indicate that above room temperature ferromagnetism in Mn-implanted Si originates not from Mn impurity but rather from structural defects in Si. The TiO(2-delta):Co thin films were deposited on LaAlO3 (001) substrates by magnetron sputtering in the argon-oxygen atmosphere at oxygen partial pressure of 2 x 10(-6)-2 x 10(-4) Torr. The obtained transverse Kerr effect spectra at the visible and XMCD spectra indicate on intrinsic room temperature ferromagnetism in TiO(2-delta):Co thin films at low (< 1%) volume fraction of Co.

H-TiO2/C/MnO2 nanocomposite materials for high-performance supercapacitors

Science.gov (United States)

Di, Jing; Fu, Xincui; Zheng, Huajun; Jia, Yi

2015-06-01

Functionalized TiO2 nanotube arrays with decoration of MnO2 nanoparticles (denoted as H-TiO2/C/MnO2) have been synthesized in the application of electrochemical capacitors. To improve both areal and gravimetric capacitance, hydrogen treatment and carbon coating process were conducted on TiO2 nanotube arrays. By scanning electron microscopy and X-ray photoelectron spectroscopy, it is confirmed that the nanostructure is formed by the uniform incorporation of MnO2 nanoparticles growing round the surface of the TiO2 nanotube arrays. Impedance analysis proves that the enhanced capacitive is due to the decrease of charge transfer resistance and diffusion resistance. Electrochemical measurements performed on this H-TiO2/C/MnO2 nanocomposite when used as an electrode material for an electrochemical pseudocapacitor presents quasi-rectangular shaped cyclic voltammetry curves up to 100 mV/s, with a large specific capacitance (SC) of 299.8 F g-1 at the current density of 0.5 A g-1 in 1 M Na2SO4 electrolyte. More importantly, the electrode also exhibits long-term cycling stability, only 13 % of SC loss after 2000 continuous charge-discharge cycles. Based on the concept of integrating active materials on highly ordered nanostructure framework, this method can be widely applied to the synthesis of high-performance electrode materials for energy storage.

Trends in (LaMnO3)n/(SrTiO3)m superlattices with varying layer thicknesses

KAUST Repository

Jilili, J.

2015-09-01

We investigate the thickness dependence of the structural, electronic, and magnetic properties of (LaMnO3)n/(SrTiO3)m (n, m = 2, 4, 6, 8) superlattices using density functional theory. The electronic structure turns out to be highly sensitive to the onsite Coulomb interaction. In contrast to bulk SrTiO3, strongly distorted O octahedra are observed in the SrTiO3 layers with a systematic off centering of the Ti atoms. The systems favour ferromagnetic spin ordering rather than the antiferromagnetic spin ordering of bulk LaMnO3 and all show half-metallicity, while a systematic reduction of the minority spin band gaps as a function of the LaMnO3 and SrTiO3 layer thicknesses originates from modifications of the Ti dxy states.

The centralized control of elemental mercury emission from the flue gas by a magnetic rengenerable Fe-Ti-Mn spinel.

Science.gov (United States)

Liao, Yong; Xiong, Shangchao; Dang, Hao; Xiao, Xin; Yang, Shijian; Wong, Po Keung

2015-12-15

A magnetic Fe-Ti-Mn spinel was developed to adsorb gaseous Hg(0) in our previous study. However, it is currently extremely restricted in the control of Hg(0) emission from the flue gas for at least three reasons: sorbent recovery, sorbent regeneration and the interference of the chemical composition in the flue gas. Therefore, the effect of SO2 and H2O on the adsorption of gaseous Hg(0) on the Fe-Ti-Mn spinel and the regeneration of spent Fe-Ti-Mn spinel were investigated in this study. Meanwhile, the procedure of the centralized control of Hg(0) emission from the flue gas by the magnetic Fe-Ti-Mn spinel has been analyzed for industrial application. The spent Fe-Ti-Mn spinel can be regenerated by water washing followed by the thermal treatment at 450 °C with no obvious decrease of its ability for Hg(0) capture. Meanwhile, gaseous Hg(0) in the flue gas can be remarkably concentrated during the regeneration, facilitating its safe disposal. Initial pilot test demonstrated that gaseous Hg(0) in the real flue gas can be concentrated at least 100 times by the Fe-Ti-Mn spinel. Therefore, Fe-Ti-Mn spinel was a novel magnetic regenerable sorbent, which can be used for the centralized control of Hg(0) emission from the flue gas. Copyright © 2015 Elsevier B.V. All rights reserved.

Cobalt-Free Permanent Magnet Alloys.

Science.gov (United States)

1984-10-01

ThC Ferrites (Zn, Mn. Cu, Fe)O A12O. Al TiC Kaolin Al203.Si02-Fe2O3 Fe2O3 Li B4C Spodumene LiAI (SiOs) 2 ThO2 Ni UC Rhodonite NtnO. SiO2 MnOs Fe TaC...minutes. X-ray diffraction pattern indicated the presence of magnetic T phase. Hysteresis loop was measured on the heat treated powder dispersed in wax...fmgei * T phse Hysersi loo was mesue on the. heat - treated ,--". " powder dispersed in wax... The’ result wer as"- follows: • , " • "• . I TABLE 6

Hydrogenation properties and microstructure of Ti-Mn-based alloys for hybrid hydrogen storage vessel

International Nuclear Information System (INIS)

Shibuya, Masachika; Nakamura, Jin; Akiba, Etsuo

2008-01-01

Ti-Mn-based AB 2 -type alloys which are suitable for a hybrid hydrogen storage vessel have been synthesized and evaluated hydrogenation properties. As the third element V was added to Ti-Mn binary alloys. All the alloys synthesized in this work mainly consist of the C14 Laves and BCC phase. In the case of Ti0.5V0.5Mn alloy, the amounts of hydrogen absorption was 1.8 wt.% at 243 K under the atmosphere of 7 MPa H 2 , and the hydrogen desorption pressure was in the range of 0.2-0.4 MPa at 243 K. The hydrogen capacity of this alloy did not saturate under 7 MPa H 2 and seems to increase with hydrogen pressure up to 35 MPa that is estimated working pressure of the hybrid hydrogen storage vessel

Mn-doped CdS quantum dots sensitized hierarchical TiO2 flower-rod for solar cell application

International Nuclear Information System (INIS)

Yu, Libo; Li, Zhen; Liu, Yingbo; Cheng, Fa; Sun, Shuqing

2014-01-01

A double-layered TiO 2 film which three dimensional (3D) flowers grown on highly ordered self-assembled one dimensional (1D) TiO 2 nanorods was synthesized directly on transparent fluorine-doped tin oxide (FTO) conducting glass substrate by a facile hydrothermal method and was applied as photoanode in Mn-doped CdS quantum dots sensitized solar cells (QDSSCs). The 3D TiO 2 flowers with the increased surface areas can adsorb more QDs, which increased the absorption of light; meanwhile 1D TiO 2 nanorods beneath the flowers offered a direct electrical pathway for photogenerated electrons, accelerating the electron transfer rate. A typical type II band alignment which can effectively separate photogenerated excitons and reduce recombination of electrons and holes was constructed by Mn-doped CdS QDs and TiO 2 flower-rod. The incident photon-to-current conversion efficiency (IPCE) of the Mn-doped CdS/TiO 2 flower-rod solar cell reached to 40% with the polysulfide electrolyte filled in the solar cell. The power conversion efficiency (PCE) of 1.09% was obtained with the Mn-doped CdS/TiO 2 flower-rod solar cell under one sun illumination (AM 1.5G, 100 mW/cm 2 ), which is 105.7% higher than that of the CdS/TiO 2 nanorod solar cell (0.53%).

Mn/TiO2 and Mn–Fe/TiO2 catalysts synthesized by deposition precipitation—promising for selective catalytic reduction of NO with NH3 at low temperatures

DEFF Research Database (Denmark)

Putluru, Siva Sankar Reddy; Schill, Leonhard; Jensen, Anker Degn

2015-01-01

Mn/TiO2and Mn–Fe/TiO2catalysts have been prepared by impregnation (IMP) and deposition-precipitation (DP) techniques and characterized by N2 physisorption, XRPD, NH3-TPD, H2-TPR, XPS and TGA. 25 wt% Mn0.75Fe0.25Ti-DP catalyst, prepared by deposition precipitation with ammonium carbamate (AC......) as a precipitating agent, showed superior low-temperature SCR (selective catalytic reduction) of NO with NH3. The superior catalytic activity of the 25 wt% Mn0.75Fe0.25Ti-DP catalyst is probably due to the presence of amorphous phases of manganese oxide, iron oxide, high surface area, high total acidity......, acidstrength and ease of reduction of manganese oxide and iron oxide on TiO2in addition to formation of an SCR active MnOx phase with high content of chemisorbed oxygen (Oα). The optimum catalyst might beused as tail-end SCR catalysts in, e.g., biomass-fired power plants and waste incineration plants....

Surface decoration with MnO{sub 2} nanoplatelets on graphene/TiO{sub 2} (B) hybrids for rechargeable lithium-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Li, Xinlu, E-mail: lixinlu@cqu.edu.cn; Zhang, Yonglai; Zhong, Qineng; Li, Tongtao; Li, Hongyi; Huang, Jiamu

2014-09-15

Graphical abstract: - Highlights: • The surface of graphene/TiO{sub 2} (B) hybrids is decorated by ultrathin MnO{sub 2} nanoplatelets. • MnO{sub 2}@graphene/TiO{sub 2} (B) composites exhibit high specific surface area of 283.9 m{sup 2} g{sup −1}. • The reversible capacity of graphene/TiO{sub 2} (B) hybrids is greatly improved by surface decoration with low content of MnO{sub 2}. - Abstract: Hierarchically ultrathin MnO{sub 2} nanoplatelets are decorated on the surface of graphene-based TiO{sub 2} (B) hybrids by a facile water-bath reaction to fabricate MnO{sub 2}@graphene/TiO{sub 2} (B) composites. The multi-component composites show high specific surface area of 283.9 m{sup 2} g{sup −1}, facilitating the electrochemical reactions with solvented lithium ions in the enlarged interface area. The reversible capacity of the composites remains 243 mA h g{sup −1} after 150 cycles, with capacity retention of 83.5%. In comparison with graphene/TiO{sub 2} (B) hybrids, the MnO{sub 2}@graphene/TiO{sub 2} (B) composites perform better rate capability, suggesting that surface decoration with MnO{sub 2} nanoplatelets can be a promising strategy to enhance the electrochemical performance of anode materials for lithium ion batteries.

Enhanced electrochemical performance of Ti substituted P2-Na2/3Ni1/4Mn3/4O2 cathode material for sodium ion batteries

International Nuclear Information System (INIS)

Zhao, Wenwen; Tanaka, Akinobu; Momosaki, Kyoko; Yamamoto, Shinji; Zhang, Fabi; Guo, Qixin; Noguchi, Hideyuki

2015-01-01

Highlights: • Ti substituted P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode was synthesized. • Structural and electrochemical properties of Na 2/3 Ni 1/4 Ti x Mn 3/4-x O 2 were studied. • Ti substituted cathodes exhibit enhanced cycleability and rate performance. • Ti substitution has impact on stabilizing the P2 structure during cycling. -- Abstract: Ti substituted P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode material with the composition of Na 2/3 Ni 1/4 Ti x Mn 3/4-x O 2 has been synthesized by solid state method. The influence of Ti substitution for Mn on the structure, morphology and electrochemical performances of P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 has been investigated. X-ray diffraction (XRD) results of Ti substituted sample show that they exhibit same diffraction patterns as those of pristine P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 . Progressive change in the lattice parameters of Ti substituted samples suggests that Mn was successfully substituted by Ti. In contrast to P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 which shows step-type voltage profiles, Ti substituted samples show sloping voltage profiles. Drastic capacity fade occurred for P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode, while Ti substituted cathodes still show high capacity retention over 92% after 25 cycles at the voltage range of 2.0-4.3 V. Even cycled at high upper cut-off voltage of 4.5 V, Ti=0.20 sample can deliver a reversible capacity of 140 mAhg −1 with the capacity retention over 92% after 25 cycles. Furthermore, Ti substituted cathodes exhibit enhanced rate capability over pristine P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode. Comparison of the Ex-situ XRD results of the cycled P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 and its substituted samples provides evidence that the improved electrochemical performance of Ti substituted cathodes would be attributed to the stabilization of the structure with Ti substitution

Toward an Active and Stable Catalyst for Oxygen Evolution in Acidic Media: Ti-Stabilized MnO2

DEFF Research Database (Denmark)

Frydendal, Rasmus; Paoli, Elisa Antares; Chorkendorff, Ib

2015-01-01

Catalysts are required for the oxygen evolution reaction, which are abundant, active, and stable in acid. MnO2 is a promising candidate material for this purpose. However, it dissolves at high overpotentials. Using first-principles calculations, a strategy to mitigate this problem by decorating...... undercoordinated surface sites of MnO2 with a stable oxide is developed here. TiO2 stands out as the most promising of the different oxides in the simulations. This prediction is experimentally verified by testing sputter-deposited thin films of MnO2 and Ti-MnO2. A combination of electrochemical measurements...

Novel Montmorillonite/TiO₂/MnAl-Mixed Oxide Composites Prepared from Inverse Microemulsions as Combustion Catalysts.

Science.gov (United States)

Napruszewska, Bogna D; Michalik-Zym, Alicja; Rogowska, Melania; Bielańska, Elżbieta; Rojek, Wojciech; Gaweł, Adam; Wójcik-Bania, Monika; Bahranowski, Krzysztof; Serwicka, Ewa M

2017-11-19

A novel design of combustion catalysts is proposed, in which clay/TiO₂/MnAl-mixed oxide composites are formed by intermixing exfoliated organo-montmorillonite with oxide precursors (hydrotalcite-like in the case of Mn-Al oxide) obtained by an inverse microemulsion method. In order to assess the catalysts' thermal stability, two calcination temperatures were employed: 450 and 600 °C. The composites were characterized with XRF (X-ray fluorescence), XRD (X-ray diffraction), HR SEM (high resolution scanning electron microscopy, N₂ adsorption/desorption at -196 °C, and H₂ TPR (temperature programmed reduction). Profound differences in structural, textural and redox properties of the materials were observed, depending on the presence of the TiO₂ component, the type of neutralization agent used in the titania nanoparticles preparation (NaOH or NH₃ (aq)), and the temperature of calcination. Catalytic tests of toluene combustion revealed that the clay/TiO₂/MnAl-mixed oxide composites prepared with the use of ammonia showed excellent activity, the composites obtained from MnAl hydrotalcite nanoparticles trapped between the organoclay layers were less active, but displayed spectacular thermal stability, while the clay/TiO₂/MnAl-mixed oxide materials obtained with the aid of NaOH were least active. The observed patterns of catalytic activity bear a direct relation to the materials' composition and their structural, textural, and redox properties.

Hydrogen storage in Ti-Mn-(FeV) BCC alloys

International Nuclear Information System (INIS)

Santos, S.F.; Huot, J.

2009-01-01

Recently, the replacement of vanadium by the less expensive (FeV) commercial alloy has been investigated in Ti-Cr-V BCC solid solutions and promising results were reported. In the present work, this approach of using (FeV) alloys is adopted to synthesize alloys of the Ti-Mn-V system. Compared to the V-containing alloys, the alloys containing (FeV) have a smaller hydrogen storage capacity but a larger reversible hydrogen storage capacity, which is caused by the increase of the plateau pressure of desorption. Correlations between the structure and the hydrogen storage properties of the alloys are also discussed.

Solid solution limits and selected mechanical properties of the quaternary L12 trialuminide Al-Ti-Mn-Mo

International Nuclear Information System (INIS)

Schneibel, J.H.

1994-01-01

Intermetallics based on the trialuminide Al 3 Ti, or on Al 11 Ti 5 , have been extensively researched in recent years. Alloying with approximately 10 at.% of first-row transition elements, such as Cr or Mn, converts the DO 22 structure of Al 3 Ti to L1 2 . Although this transition to the L1 2 structure increases the number of independent slip systems to five and causes substantial softening, room-temperature tensile ductilities and fracture toughnesses remain low. Typical values for the room-temperature ductilities of Al-25Ti-8Cr and Al-25Ti-9Mn are 0.2% and room-temperature fracture toughnesses of trialuminides range from 2 to 5 MPa m 1/2 . Reasons for the low fracture toughness of trialuminides have been discussed by Turner et al. and George et al. On a phenomenological basis, it appears that fracture toughnesses might improve, if either Poisson's ratio or the ratio of the bulk and shear moduli can be increased. In principle, this might be achieved by macroalloying ternary L1 2 trialuminides, while at the same time maintaining the L1 2 crystal structure. Focusing on first-row transition elements, Kumar and Brown investigated a range of such quaternary compounds. They did not observe any improvement in ductility, as compared to the ternary compounds. In the present work, it was decided to focus on a second-row transition element, namely, 2 molybdenum. As compared to Cr and Mn, which are only slightly soluble in Al 3 Ti, up to 20 at. % Mo dissolves in Al 3 Ti at 1,198 K. This raises the question whether substantial amounts of Mo also dissolve in the cubic ternary trialuminides such as Al-Ti-Mn. In order to verify this possibility, the extent of the single-phase region of cubic Al-Ti-Mn-Mo intermetallic was mapped out at 1,473 K. In addition, a limited characterization of room-temperature mechanical properties was carried out

Scalable Synthesis of Triple-Core-Shell Nanostructures of TiO2 @MnO2 @C for High Performance Supercapacitors Using Structure-Guided Combustion Waves.

Science.gov (United States)

Shin, Dongjoon; Shin, Jungho; Yeo, Taehan; Hwang, Hayoung; Park, Seonghyun; Choi, Wonjoon

2018-03-01

Core-shell nanostructures of metal oxides and carbon-based materials have emerged as outstanding electrode materials for supercapacitors and batteries. However, their synthesis requires complex procedures that incur high costs and long processing times. Herein, a new route is proposed for synthesizing triple-core-shell nanoparticles of TiO 2 @MnO 2 @C using structure-guided combustion waves (SGCWs), which originate from incomplete combustion inside chemical-fuel-wrapped nanostructures, and their application in supercapacitor electrodes. SGCWs transform TiO 2 to TiO 2 @C and TiO 2 @MnO 2 to TiO 2 @MnO 2 @C via the incompletely combusted carbonaceous fuels under an open-air atmosphere, in seconds. The synthesized carbon layers act as templates for MnO 2 shells in TiO 2 @C and organic shells of TiO 2 @MnO 2 @C. The TiO 2 @MnO 2 @C-based electrodes exhibit a greater specific capacitance (488 F g -1 at 5 mV s -1 ) and capacitance retention (97.4% after 10 000 cycles at 1.0 V s -1 ), while the absence of MnO 2 and carbon shells reveals a severe degradation in the specific capacitance and capacitance retention. Because the core-TiO 2 nanoparticles and carbon shell prevent the deformation of the inner and outer sides of the MnO 2 shell, the nanostructures of the TiO 2 @MnO 2 @C are preserved despite the long-term cycling, giving the superior performance. This SGCW-driven fabrication enables the scalable synthesis of multiple-core-shell structures applicable to diverse electrochemical applications. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Electrodeposition synthesis of MnO{sub 2}/TiO{sub 2} nanotube arrays nanocomposites and their visible light photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Xu, Xuyao [School of Chemistry Science and Technology, and Institute of Physical Chemistry, Zhanjiang Normal University, Zhanjiang 524048 (China); Zhou, Xiaosong, E-mail: zxs801213@163.com [School of Chemistry Science and Technology, and Institute of Physical Chemistry, Zhanjiang Normal University, Zhanjiang 524048 (China); Li, Xiaoyu, E-mail: lixiaoyu@iga.ac.cn [Key Laboratory of Wetland Ecology and Environment, Northeast Institute of Geography and Agroecology, Chinese Academy of Science, Changchun 130012 (China); Yang, Fei [The State Key Laboratory of Resources and Environmental Information System, Institute of Geographic Sciences and Natural Resources Research of Chinese Academy of Sciences, 11A, Datun Road, Chaoyang District, Beijing 100101 (China); Jin, Bei; Xu, Tan; Li, Guosheng; Li, Manyi [School of Chemistry Science and Technology, and Institute of Physical Chemistry, Zhanjiang Normal University, Zhanjiang 524048 (China)

2014-11-15

Highlights: • MnO{sub 2}/TiO{sub 2} nanotube arrays nanocomposites are prepared by electrodeposition. • MnO{sub 2}/TiO{sub 2} exhibits high visible light photocatalytic activity. • The results of XRD show the depositions are attributed to α-MnO{sub 2}. • A photocatalytic mechanism is discussed under visible light irradiation. - Abstract: MnO{sub 2}/TiO{sub 2} nanotube arrays nanocomposite photocatalysts have been synthesized through an electrodeposition method. X-ray powder diffraction analysis and X-ray photoelectron spectroscopy measurements reveal that the products of electrodeposition method are MnO{sub 2}. Scanning electron microscopy measurements suggest that the depositions are deposited on the surface or internal of the nanotube. UV–vis light absorbance spectra demonstrate the excellent adsorption properties of MnO{sub 2}/TiO{sub 2} over the whole region of visible light, which enables this novel photocatalytic material to possess remarkable activity in the photocatalytic degradation of acid Orange II under visible light radiation. Moreover, a possible photocatalytic mechanism is discussed.

A -Site Ordered Double Perovskite CaMnTi ₂ O ₆ as a Multifunctional Piezoelectric and Ferroelectric–Photovoltaic Material

Energy Technology Data Exchange (ETDEWEB)

Gou, Gaoyang [Frontier Institute; Charles, Nenian [Department of Materials Science and Engineering, Drexel University, Philadelphia, Pennsylvania 19104, United States; Shi, Jing [MOE Key Laboratory; Rondinelli, James M. [Department; Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, United States

2017-09-11

The double perovskite CaMnTi2O6, is a rare A site ordered perovskite oxide that exhibits a sizable ferroelectric polarization and relatively high Curie temperature. Using first-principles calculations combined with detailed symmetry analyses, we identify the origin of the ferroelectricity in CaMnTi2O6. We further explore the material properties of CaMnTi2O6, including its ferroelectric polarization, dielectric and piezoelectric responses, magnetic order, electronic structure, and optical absorption coefficient. It is found that CaMnTi2O6 exhibits room-temperature-stable ferroelectricity and moderate piezoelectric responses. Moreover, CaMnTi2O6 is predicted to have a semiconducting energy band gap similar to that of BiFeO3, and its band gap can further be tuned-via distortions of the planar Mn-O bond lengths. CaMnTi2O6 exemplifies a new class of single-phase semiconducting ferroelectric perovskites for potential applications in ferroelectric photovoltaic solar cells.

Fabrication of band gap engineered nanostructured tri-metallic (Mn-Co-Ti) oxide thin films

Science.gov (United States)

Mansoor, Muhammad Adil; Yusof, Farazila Binti; Nay-Ming, Huang

2018-04-01

In continuation of our previous studies on photoelectrochemical (PEC) properties of titanium based composite oxide thin films, an effort is made to develop thin films of 1:1:2 manganese-cobalt-titanium oxide composite, Mn2O3-Co2O3-4TiO2 (MCT), using Co(OAc)2 and a bimetallic manganese-titanium complex, [Mn2Ti4(TFA)8(THF)6(OH)4(O)2].0.4THF (1), where OAc = acetato, TFA = trifluoroacetato and THF = tetrahydrofuran, via aerosol-assisted chemical vapour deposition (AACVD) technique. The X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and energy dispersive X-ray (EDX) spectroscopic analyses confirmed formation of thin film of Mn2O3-Co2O3-4TiO2 composite material with uniformly distributed agglomerated particles. The average size of 39.5 nm, of the particles embedded inside agglomerates, was estimated by Scherer's equation. Further, UV-Vis spectroscopy was used to estimate the band gap of 2.62 eV for MCT composite thin film.

Effect of Ti doping on magnetic properties and magnetoresistance in LaSr2Mn2O7

International Nuclear Information System (INIS)

Feng, J.; Che, P.; Wang, J.P.; Lu, M.F.; Liu, J.F.; Cao, X.Q.; Meng, J.

2005-01-01

The effect of Ti substitution for Mn on magnetic and transport properties has been investigated for layered manganese oxides LaSr 2 Mn 2-x Ti x O 7 . Titanium doping hampered the canted antiferromagnetic (AFM) exchange at low temperature and their Neel temperature (T N ) decreased from 138 K (x = 0) to 106 K (x = 0.1). Meanwhile, spin glass, charge ordering and metal-insulator transition are suppressed by Ti addition. This can be attributed to Mn-site disorder caused by random substitution of Ti 4+ . The suppression of charge ordering leads to magntetoresistance (MR) ratio increase and MR reaches maximum at x = 0.3. The resistivity increases obviously with x increasing because of double exchange interaction channel broken by Ti 4+ addition. The resistivity of all samples in low temperature range fits to the Mott's variable range hopping (VRH) model, while it fits to nearest neighbor hopping of small polarons model in high temperature range. We also found that both disorder and distortion in A-site and B-site will induce the similar effect to electrical and magnetic properties

Enhanced high-potential and elevated-temperature cycling stability of LiMn2O4 cathode by TiO2 modification for Li-ion battery

International Nuclear Information System (INIS)

Yu Lihong; Qiu Xinping; Xi Jingyu; Zhu Wentao; Chen Liquan

2006-01-01

The surface of spinel LiMn 2 O 4 was modified with TiO 2 by a simple sol-gel method to improve its electrochemical performance at elevated temperatures and higher working potentials. Compared with pristine LiMn 2 O 4 , surface-modification improved the cycling stability of the material. The capacity retention of TiO 2 -modified LiMn 2 O 4 was more than 85% after 60 cycles at high potential cycles between 3.0 and 4.8 V at room temperature and near to 90% after 30 cycles at elevated temperature of 55 deg. C at 1C charge-discharge rate. SEM studies shows that the surface morphology of TiO 2 -modified LiMn 2 O 4 was different from that of pristine LiMn 2 O 4 . Powder X-ray diffraction indicated that spinel was the only detected phase in TiO 2 -modified LiMn 2 O 4 . Introduction of Ti into LiMn 2 O 4 changed the electronic structures of the particle surface. Therefore a surface solid compound of LiTi x Mn 2-x O 4 may be formed on LiMn 2 O 4 . The improved electrochemical performance of surface-modified LiMn 2 O 4 was attributed to the improved stability of crystalline structure and the higher Li + conductivity

Band gap depiction of quaternary FeMnTiAl alloy using Hubbard (U) potential

Science.gov (United States)

Bhat, Tahir Mohiuddin; Yousuf, Saleem; Khandy, Shakeel Ahmad; Gupta, Dinesh C.

2018-05-01

We have employed self-consistent ab-initio calculations to investigate new quaternary alloy FeMnTiAl by applying Hubbard potential (U). The alloy is found to be stable in ferromagnetic phase with cubic structure. The alloy shows half-metallic (HM) ferromagnet character. The values of minority band gap FeMnTiAl are found to be 0.33 eV respectively. Electronic charge density reveals that both types of bonds covalent as well as ionic are present in the alloy. Thus the new quaternary alloy can be proved as vital contender for spin valves and spin generator devices.

High mobility half-metallicity in the (LaMnO3)2/(SrTiO3)8 superlattice

KAUST Repository

Cossu, Fabrizio

2013-01-28

First principles calculations have been performed to investigate the LaMnO3/SrTiO3 superlattice. Structural relaxation within the generalized gradient approximation results in no significant tiltings or rotations of oxygen octahedra, but in distinct distortions in the SrTiO3 region. Taking into account the onsite Coulomb interaction, we find that the Mn spins order ferromagnetically, in contrast to the antiferromagnetic state of bulk LaMnO3. Most importantly, the interface strain combined with charge transfer across the interface induces half-metallicity within the MnO2 layers. The superlattice is particulary interesting for spintronics applications because the half-metallic states are characterized by an extraordinary high mobility.

High mobility half-metallicity in the (LaMnO3)2/(SrTiO3)8 superlattice

KAUST Repository

Cossu, Fabrizio; Schwingenschlö gl, Udo; Singh, Nirpendra

2013-01-01

First principles calculations have been performed to investigate the LaMnO3/SrTiO3 superlattice. Structural relaxation within the generalized gradient approximation results in no significant tiltings or rotations of oxygen octahedra, but in distinct distortions in the SrTiO3 region. Taking into account the onsite Coulomb interaction, we find that the Mn spins order ferromagnetically, in contrast to the antiferromagnetic state of bulk LaMnO3. Most importantly, the interface strain combined with charge transfer across the interface induces half-metallicity within the MnO2 layers. The superlattice is particulary interesting for spintronics applications because the half-metallic states are characterized by an extraordinary high mobility.

Effects of flue gas components on removal of elemental mercury over Ce–MnO_x/Ti-PILCs

International Nuclear Information System (INIS)

He, Chuan; Shen, Boxiong; Li, Fukuan

2016-01-01

Highlights: • Ce–MnO_x/Ti-PILC exhibited high Hg"0 removal activity. • SO_2 restrained Hg"0 oxidation and adsorption due to the formation of SO_4"2"−. • The formation of NH_3 to NH_4"+ restrained the Hg"0 adsorption and oxidation. - Abstract: The adsorption and oxidation of elemental mercury (Hg"0) under various flue gas components were investigated over a series of Ce–MnO_x/Ti-PILC catalysts, which were synthesized by an impregnation method. To discuss the mechanism, the catalysts were characterized by various techniques such as N_2 adsorption–desorption, scanning electron microscope (SEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) analysis and X-ray photoelectron spectroscopy (XPS). The results indicated that the presence of 500 ppm SO_2 in the flue gas significantly restrained the Hg"0 adsorption and oxidation over 6%Ce–6%MnO_x/Ti-PILC due to the formation of SO_4"2"− species. Hg"0 could be oxidized to HgCl_2 in the presence of HCl, because the Deacon process occurred. NO would react with active oxygen to form NO_2-containing species, which facilitated Hg"0 oxidation. While the presence of NO limited the Hg"0 adsorption on 6%Ce–6%MnO_x/Ti-PILC due to the competitive adsorption of NO with Hg"0. The addition of NH_3 in the flue gas significantly restrained Hg"0 adsorption and oxidation, because the formed NH_4"+ species covered the active adsorption sites on the surfaces, and further limited Hg"0 oxidation. However, when NO and NH_3 were simultaneously added into the flue gas, the Hg"0 oxidation efficiency of 6%Ce–6%MnO_x/Ti-PILC exhibited a relatively high value (72%) at 250 °C, which indicated the practicability to use Ce–MnO_x/Ti-PILC for Hg"0 removal under SCR conditions.

Synthesis and enhanced electrochemical performance of the honeycomb TiO2/LiMn2O4 cathode materials

DEFF Research Database (Denmark)

Zhang, J.Y.; Shen, J.X.; Wei, C.B.

2016-01-01

angle compare to LiMn2O4, implying that TiO2 doping induced a change of crystal structure. By performing electrochemical measurements, we observed an enhancement of specific capacity (127.28 mAhg−1) and an improvement of cycling stability in the TiO2/LiMn2O4 hybrid materials. After 100 cycles of charge...

Defect annealing in Mn/Fe-implanted TiO2 (rutile)

International Nuclear Information System (INIS)

Gunnlaugsson, H P; Svane, A; Weyer, G; Mantovan, R; Masenda, H; Naidoo, D; Mølholt, T E; Gislason, H; Ólafsson, S; Johnston, K; Bharuth-Ram, K; Langouche, G

2014-01-01

A study of the annealing processes and charge state of dilute Fe in rutile TiO 2 single crystals was performed in the temperature range 143–662 K, utilizing online 57 Fe emission Mössbauer spectroscopy following low concentrations (<10 −3  at%) implantation of 57 Mn (T 1/2  = 1.5 min). Both Fe 3+ and Fe 2+ were detected throughout the temperature range. Three annealing stages were distinguished: (i) a broad annealing stage below room temperature leading to an increased Fe 3+ fraction; (ii) a sharp annealing stage at ∼330 K characterized by conversion of Fe 3+ to Fe 2+ and changes in the hyperfine parameters of Fe 2+ , attributed to the annealing of Ti vacancies in the vicinity of the probe atoms; and (iii) an annealing stage in the temperature range from 550 to 600 K, where all Fe ions are transformed to Fe 3+ , attributed to the annealing of the nearby O vacancies. The dissociation energy of Mn Ti –V O pairs was estimated to be 1.60(15) eV. Fe 2+ is found in an environment where it can probe the lattice structure through the nuclear quadrupole interaction evidencing the extreme radiation hardness of rutile TiO 2 . Fe 3+ is found in a paramagnetic state with slow spin–lattice relaxation which follows a ∼T n temperature dependence with 4.1 < n < 6.3 at T > 350 K. (paper)

H–TiO{sub 2}/C/MnO{sub 2} nanocomposite materials for high-performance supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Di, Jing; Fu, Xincui; Zheng, Huajun, E-mail: zhenghj@zjut.edu.cn [Zhejiang University of Technology, Department of Applied Chemistry (China); Jia, Yi [Griffith University, Nathan Campus, Queensland Micro and Nanotechnology Centre (Australia)

2015-06-15

Functionalized TiO{sub 2} nanotube arrays with decoration of MnO{sub 2} nanoparticles (denoted as H–TiO{sub 2}/C/MnO{sub 2}) have been synthesized in the application of electrochemical capacitors. To improve both areal and gravimetric capacitance, hydrogen treatment and carbon coating process were conducted on TiO{sub 2} nanotube arrays. By scanning electron microscopy and X-ray photoelectron spectroscopy, it is confirmed that the nanostructure is formed by the uniform incorporation of MnO{sub 2} nanoparticles growing round the surface of the TiO{sub 2} nanotube arrays. Impedance analysis proves that the enhanced capacitive is due to the decrease of charge transfer resistance and diffusion resistance. Electrochemical measurements performed on this H–TiO{sub 2}/C/MnO{sub 2} nanocomposite when used as an electrode material for an electrochemical pseudocapacitor presents quasi-rectangular shaped cyclic voltammetry curves up to 100 mV/s, with a large specific capacitance (SC) of 299.8 F g{sup −1} at the current density of 0.5 A g{sup −1} in 1 M Na{sub 2}SO{sub 4} electrolyte. More importantly, the electrode also exhibits long-term cycling stability, only ∼13 % of SC loss after 2000 continuous charge–discharge cycles. Based on the concept of integrating active materials on highly ordered nanostructure framework, this method can be widely applied to the synthesis of high-performance electrode materials for energy storage.

The Adsorption Langmuir Model of Transfer Metal Ti, V and Mn on System Water-Sediment in Along Side Code River, Yogyakarta

International Nuclear Information System (INIS)

Rini Jati Wardani; Muzakky; Agus Taftazani

2007-01-01

The adsorption langmuir model of transfer metal Ti, V and Mn on system water-sediment in along side Code river, Yogyakarta has been studied. For that purpose, the study is to make prediction about adsorption langmuir model of identified metal Ti, V and Mn from upstream until downstream samples water and sediment in along side Code river. The factor influenced of langmuir adsorption on transfer metal Ti, V and Mn in system water-sediment is Total Suspended Solid (TSS). The analysis showed that between TSS with metal concentration in sediment have linear correlation. The result of calculation from curve of langmuir isotherm, showed for Ti has R 2 = 0.8006 with capacities of adsorption = 0.5 mol/l and energy of adsorption = 13.286 J/mol, V has R 2 = 0.9883 with capacities of adsorption = 0.0137 mol/l and energy of adsorption = 16.64 J/mol, Mn has R 2 = 0.9624 with capacities of adsorption 0.152 mol/l and energy of adsorption = 10.51 J/mol. The conclusion from this topic about adsorption langmuir for metal Ti, V and Mn according to energy of langmuir adsorption by chemisorption process above 10 J/mo. (author)

Novel Montmorillonite/TiO2/MnAl-Mixed Oxide Composites Prepared from Inverse Microemulsions as Combustion Catalysts

Directory of Open Access Journals (Sweden)

Bogna D. Napruszewska

2017-11-01

Full Text Available A novel design of combustion catalysts is proposed, in which clay/TiO2/MnAl-mixed oxide composites are formed by intermixing exfoliated organo-montmorillonite with oxide precursors (hydrotalcite-like in the case of Mn-Al oxide obtained by an inverse microemulsion method. In order to assess the catalysts’ thermal stability, two calcination temperatures were employed: 450 and 600 °C. The composites were characterized with XRF (X-ray fluorescence, XRD (X-ray diffraction, HR SEM (high resolution scanning electron microscopy, N2 adsorption/desorption at −196 °C, and H2 TPR (temperature programmed reduction. Profound differences in structural, textural and redox properties of the materials were observed, depending on the presence of the TiO2 component, the type of neutralization agent used in the titania nanoparticles preparation (NaOH or NH3 (aq, and the temperature of calcination. Catalytic tests of toluene combustion revealed that the clay/TiO2/MnAl-mixed oxide composites prepared with the use of ammonia showed excellent activity, the composites obtained from MnAl hydrotalcite nanoparticles trapped between the organoclay layers were less active, but displayed spectacular thermal stability, while the clay/TiO2/MnAl-mixed oxide materials obtained with the aid of NaOH were least active. The observed patterns of catalytic activity bear a direct relation to the materials’ composition and their structural, textural, and redox properties.

Coupling catalytic hydrolysis and oxidation on Mn/TiO2-Al2O3 for HCN removal

Science.gov (United States)

Wang, Langlang; Wang, Xueqian; Cheng, Jinhuan; Ning, Ping; Lin, Yilong

2018-05-01

The manganese-modified titania-alumina (Mn/TiO2-Al2O3) catalyst synthesized by sol-gol method was used to remove hydrogen cyanide (HCN) from simulated flue gas. Further, effects of the mass ratios of Ti/Al, Mn loading, calcination temperature, and relative humidity on HCN conversion efficiency and catalytic activity were systematically investigated. The results indicated that the Mn/TiO2-Al2O3 catalyst exhibited significantly enhanced HCN removal efficiency, and the maximum yield of N2 increased to 68.02% without the participation of water vapor. When water vapor was added into the flue gas, the yield of N2 decreased and the formation of NOx was also inhibited. The XRD and XPS results indicated that Mn was mainly present in the form of Mn2+, Mn3+, and Mn4+ on the surface of catalyst and chemisorbed oxygen played a major role in the HCN catalytic oxidation process. The results of DSC-TGA analysis and H2-TPR indicated that the catalyst also exhibited a good thermal and chemical stability. NH3-TPD and CO2-TPD indicated that the surface of the catalyst mainly contained acidic sites. During the reaction, part of NH3 was adsorbed by Brönsted and Lewis acid sites. NH3 adsorbed on Lewis acid sites participated in NH3-SCR, which reduced the amount of NOx produced and resulted in a high N2 yield.

Spin-polarized electron gas in Co2MSi/SrTiO3(M= Ti, V, Cr, Mn, and Fe) heterostructures

KAUST Repository

Nazir, S.

2016-06-08

Spin-polarized density functional theory is used to study the TiO2 terminated interfaces between the magnetic Heusler alloys Co2Si (M = Ti, V, Cr, Mn, and Fe) and the non-polar band insulator SrTiO3. The structural relaxation at the interface turns out to depend systematically on the lattice mis- match. Charge transfer from the Heusler alloys (mainly the M 3d orbitals) to the Ti dxy orbitals of the TiO2 interface layer is found to gradually grow from M = Ti to Fe, resulting in an electron gas with increasing density of spin-polarized charge carriers. (© 2016 WILEY-VCH Verlag GmbH &Co. KGaA, Weinheim). © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Effect of Mn and AlTiB Addition and Heattreatment on the Microstructures and Mechanical Properties of Al-Si-Fe-Cu-Zr Alloy.

Science.gov (United States)

Yoo, Hyo-Sang; Kim, Yong-Ho; Lee, Seong-Hee; Son, Hyeon-Taek

2018-09-01

The microstructure and mechanical properties of as-extruded Al-0.1 wt%Si-0.2 wt%Fe- 0.4 wt%Cu-0.04 wt%Zr-xMn-xAlTiB (x = 1.0 wt%) alloys under various annealing processes were investigated and compared. After the as-cast billets were kept at 400 °C for 1 hr, hot extrusion was carried out with a reduction ratio of 38:1. In the case of the as-extruded Al-Si-Fe-Cu-Zr alloy at annealed at 620 °C, large equiaxed grain was observed. When the Mn content is 1.0 wt%, the phase exhibits a skeleton morphology, the phase formation in which Mn participated. Also, the volume fraction of the intermetallic compounds increased with Mn and AlTiB addition. For the Al-0.1Si-0.2Fe-0.4Cu-0.04Zr alloy with Mn and AlTiB addition from 1.0 wt%, the ultimate tensile strength increased from 100.47 to 119.41 to 110.49 MPa. The tensile strength of the as-extruded alloys improved with the addition of Mn and AlTiB due to the formation of Mn and AlTiB-containing intermetallic compounds.

Thermo-mechanical treatment of low-cost alloy Ti-4.5Al-6.9Cr-2.3Mn and microstructure and mechanical characteristics

Science.gov (United States)

Chen, Guangyao; Kang, Juyun; Wang, Shusen; Wang, Shihua; Lu, Xionggang; Li, Chonghe

2018-04-01

In this study, the thermo-mechanical treatment process for low-cost Ti-4.5Al-6.9Cr-2.3Mn alloy were designed on the basis of assessment of Ti-Al-Cr-Mn thermodynamic system. The microstructure and mechanical properties of Ti-4.5Al-6.9Cr-2.3Mn forging and sheet were investigated by using the OM, SEM and universal tensile testing machine. The results show that both the forging and sheet were consisted of α + β phase, which is consistent with the expectation, and no element Cr and Mn existed in the grain boundaries of the sheet after quenching, and the C14 laves phase was not detected. The average ultimate tensile strength (σ b), 0.2% proof strength (σ 0.2) and elongation (EI) of alloy sheet after quenching can reach 1059 MPa, 1051 MPa and 24.6 Pct., respectively. Moreover, the average ultimate tensile strength of Ti-4.5Al-6.9Cr-2.3Mn forgings can reach 1599 MPa and the average elongation can reach 11.2 Pct., and a more excellent property of Ti-4.5Al-6.9Cr-2.3Mn forging is achieved than that of TC4 forging. It provides a theoretical support for further developing this low-cost alloy.

Calculation of phase equilibria in Ti-Al-Cr-Mn quaternary system for developing lower cost titanium alloys

International Nuclear Information System (INIS)

Lu, X.G.; Li, C.H.; Chen, L.Y.; Qiu, A.T.; Ding, W.Z.

2011-01-01

Highlights: → This paper is about the concept of designing the lower cost titanium alloy. → The thermodynamic database of Ti-Al-Cr-Mn system is built up by Calphad method. → The pseudobinary sections with Cr: Mn = 3:1 and Al = 3, 4.5 and 6.0 wt% are calculated. → This may provide the theoretical support for designing the lower cost titanium alloy. - Abstract: The Ti-Al-Cr-Mn system is a potentially useful system for lower cost titanium alloy development; however, there are few reports about the experimental phase diagrams and the thermodynamical assessment for this system. In this study, the previous investigations for the thermodynamic descriptions of the sub-systems in the Ti-Al-Cr-Mn system are reviewed, our previous assessment for the related sub-systems in this quaternary system is summarized, the thermodynamical database of this quaternary system is built up by directly extrapolating from all sub-systems assessed by means of the Calphad method, then the pseudobinary sections with Cr:Mn = 3:1 and Al = 0.0, 3.0, 4.5 and 6.0 wt% are calculated, respectively. These pseudobinary phase diagrams may provide the theoretical support for designing the lower cost titanium alloys with different microstructures (α, α + β, and β titanium alloy).

Lithium-Excess Research of Cathode Material Li2MnTiO4 for Lithium-Ion Batteries

OpenAIRE

Zhang, Xinyi; Yang, Le; Hao, Feng; Chen, Haosen; Yang, Meng; Fang, Daining

2015-01-01

Lithium-excess and nano-sized Li2+xMn1−x/2TiO4 (x = 0, 0.2, 0.4) cathode materials were synthesized via a sol-gel method. The X-ray diffraction (XRD) experiments indicate that the obtained main phases of Li2.0MnTiO4 and the lithium-excess materials are monoclinic and cubic, respectively. The scanning electron microscope (SEM) images show that the as-prepared particles are well distributed and the primary particles have an average size of about 20–30 nm. The further electrochemical tests revea...

K{sub 2}MnF{sub 5}·H{sub 2}O as reactant for synthesizing highly efficient red emitting K{sub 2}TiF{sub 6}:Mn{sup 4+} phosphors by a modified cation exchange approach

Energy Technology Data Exchange (ETDEWEB)

Han, Tao, E-mail: danbaiht@126.com; Wang, Jun; Lang, Tianchun; Tu, Mingjing; Peng, Lingling

2016-11-01

As reactant for synthesizing K{sub 2}TiF{sub 6}:Mn{sup 4+} phosphors, the cross-shaped and cuboid-shaped K{sub 2}MnF{sub 5}·H{sub 2}O powders were prepared by the simple chemical method. Based on the reaction mechanism, oxidizing K{sub 2}MnF{sub 5}·H{sub 2}O (Mn{sup 3+}) to Mn{sup 4+} by KMnO{sub 4} (Mn{sup 7+}), a modified cation exchange approach for synthesizing highly efficient red emitting K{sub 2}TiF{sub 6}:Mn{sup 4+} phosphor was proposed. The obtained K{sub 2}TiF{sub 6}:Mn{sup 4+} (2.7–5.3 at.%) phosphors have the size of 30–80 μm with a rough surface, their emission spectra consist of five narrow bands extending from 580 to 660 nm with the strongest peak at 634.8 nm, whose relative emitting intensity depends on the molar ratio of KMnO{sub 4} to K{sub 2}MnF{sub 5}·H{sub 2}O (the platform value = 3.2), and two broad excitation bands are peaking at ∼365 nm and ∼460 nm. The internal quantum yield of our synthesized K{sub 2}TiF{sub 6}:Mn{sup 4+} phosphors is up to 82.5%, which is higher than the commercial CaAlSiN{sub 3}:Eu{sup 2+} value, their excitation bands peak at ∼460 and ∼365 nm are consistent with those of Y{sub 3}A{sub 5}O{sub 12}:Ce{sup 3+} phosphors and their emission bands are more suitable for the sensitivity curve of photopic human vision. In addition, our synthesized phosphors show better thermal quenching properties. These findings show a large potential of the synthesized K{sub 2}TiF{sub 6}:Mn{sup 4+} phosphors for commercialization. - Highlights: • We synthesize the cross-shaped and cuboid-shaped K{sub 2}MnF{sub 5}·H{sub 2}O. • K{sub 2}MnF{sub 5}·H{sub 2}O is as a reactant for synthesizing K{sub 2}TiF{sub 6}:Mn{sup 4+} phosphors. • K{sub 2}TiF{sub 6}:Mn{sup 4+} will improve the current white LED with high CRI for indoor lighting.

Synthesis and Piezoelectric Properties of Li, Ca and Mn-codoped BaTiO3 by a Solvothermal Approach

International Nuclear Information System (INIS)

Kimura, T; Dong, Q; Yin, S; Sato, T; Hashimoto, T; Sasaki, A; Aisawa, S

2013-01-01

3 at.% Li-doped (Ba 1-x Ca x )(Ti 1-y Mn y )O 3 particles with the Ca 2+ mole fraction, x, of 0–0.09 and Mn mole fraction, y, of 0 and 0.0005 were synthesized by a solvothermal approach at 200°C. The products consisted of nanoparticles of 50–100 nm in diameter, and did not change very much depending on the amount of Li, Ca and Mn-codoping. The change in relative dielectric constant, Δε r , in around room temperature decreased by doping Ca 2+ , and the lowest Δε r (4.51%) could be realized at x value of 0.03. The mechanical quality factor, Q m , of 3 at.% Li-doped (Ba 0.97 Ca 0.03 )(Ti 0.9995 Mn 0.0005 )O 3 increased to 521, and Δε r decreased to 1.72%, while the piezoelectric constant, d 33 (234pC/N), and electromechanical coupling factor, k p (40.0%), did not change very much compared with 3 at.% Li-doped BaTiO 3

Ti@δ-MnO_2 core-shell nanowire arrays as self-supported electrodes of supercapacitors and Li ion batteries

International Nuclear Information System (INIS)

Zhao, Guangyu; Zhang, Dong; Zhang, Li; Sun, Kening

2016-01-01

Highlights: • Ti@δ-MnO_2 core-shell nanowire arrays prepared by a electrochemical method. • Remarkable rate capability as both Li ion battery and supercapacitor electrodes. • Good electronic conductivity and facilitated mass transport. - Abstract: δ-MnO_2 is a promissing electrode material of supercapacitors and Li ion batteries (LIBs) owing to its low cost, layer structure and composite valence of Mn. However, the unfavorable electronic conductivity of δ-MnO_2 restricts its rate capability in both of the two devices. Herein, a vertically standing Ti nanowire array modified with δ-MnO_2 nanoflakes is prepared by a electrodeposition method, and the electrochemical properties of Ti@δ-MnO_2 nanowire arrays in supercapacitors and LIBs are investigated. The results show that, the arrays have a capacity of 195 F g"−"1 at 1.0 A g"−"1 and can cycle more than 10000 rounds at 10 A g"−"1 as electrodes of supercapacitors. On the other hand, the arrays behave good rate capability as LIB cathodes, which can release a capacity of 70 mAh g"−"1 at 10C rate charge/discharge. We suggest that, the good electronic conductivity owing to the core-shell structure and the facilitated mass transport supplied by the array architecture are responsible for the enhanced rate performances in the two devices.

Magnetic Properties and Magnetocaloric Effect in Layered NdMn1.9Ti0.1Si2

Directory of Open Access Journals (Sweden)

M.F. Md Din

2014-04-01

Full Text Available The structural and magnetic properties of the NdMn1.9Ti0.1Si2 compund have been studied by high-intensity x-ray and high-resolution neutron powder diffraction, specific heat, dc magnetization, and differential scanning calorimetry measurements over the temperature range of 3-450 K. The Curie temperature and Néel temperature of layered NdMn1.9Ti0.1Si2 are indicated as TC ~ 22 K and TN ~ 374 K respectively. The first order magnetic transition from antiferromagnetic [AFil-type] to ferromagnetic [F(Nd+Fmc] around TC is found in layered NdMn1.9Ti0.1Si2 and is associated with large magnetocaloric effect. This behavior has been confirmed as a contribution of the magnetostructural coupling by using neutron and x-ray powder diffraction. The magnetic entropy change –ΔSM ~ 15.3 J kg-1 K-1 and adiabatic temperature change ΔTad ~ 4.7 K have been determined using magnetization and specific heat measurement under 0-5 T applied fields. This compound exhibits almost no thermal and magnetic hysteresis, thus potentially applicable in low temperature region for magnetic refrigerator material

The design of an Fe-12Mn-O.2Ti alloy steel for low temperature use

Science.gov (United States)

Hwang, S. K.; Morris, J. W., Jr.

1977-01-01

An investigation was made to improve the low temperature mechanical properties of Fe-8 approximately 12% Mn-O 2Ti alloy steels. A two-phase(alpha + gamma) tempering in combination with cold working or hot working was identified as an effective treatment. A potential application as a Ni-free cryogenic steel was shown for this alloy. It was also shown that an Fe-8Mn steel could be grain-refined by a purely thermal treatment because of its dislocated martensitic structure and absence of epsilon phase. A significant reduction of the ductile-brittle transition temperature was obtained in this alloy. The nature and origin of brittle fracture in Fe-Mn alloys were also investigated. Two embrittling regions were found in a cooling curve of an Fe-12Mn-O 2Ti steel which was shown to be responsible for intergranular fracture. Auger electron spectroscopy identified no segregation during solution-annealing treatment. Avoiding the embrittling zones by controlled cooling led to a high cryogenic toughness in a solution-annealed condition.

The Poisoning Effect of Na Doping over Mn-Ce/TiO2 Catalyst for Low-Temperature Selective Catalytic Reduction of NO by NH3

Directory of Open Access Journals (Sweden)

Liu Yang

2014-01-01

Full Text Available Sodium carbonate (Na2CO3, sodium nitrate (NaNO3, and sodium chloride (NaCl were chosen as the precursors to prepare the Na salts deposited Mn-Ce/TiO2 catalysts through an impregnation method. The influence of Na on the performance of the Mn-Ce/TiO2 catalyst for low-temperature selective catalytic reduction of NOx by NH3 was investigated. Experimental results showed that Na salts had negative effects on the activity of Mn-Ce/TiO2 and the precursors of Na salts also affected the catalytic activity. The precursor Na2CO3 had a greater impact on the catalytic activity, while NaNO3 had minimal effect. The characterization results indicated that the significant changes in physical and chemical properties of Mn-Ce/TiO2 were observed after Na was doped on the catalysts. The significant decreases in surface areas and NH3 adsorption amounts were observed after Na was doped on the catalysts, which could be considered as the main reasons for the deactivation of Na deposited Mn-Ce/TiO2.

OPTIMIZATION OF STEEL SATURATION PROCESSES USING CARBIDE-FORMING ELEMENTS IN SYSTEMS BASED ON Cr-Ti-V AND Cr-Ti-Mn

Directory of Open Access Journals (Sweden)

A. A. Shmatov

2007-01-01

Full Text Available Optimization of saturating mixture compositions has been carried out in two three-component systems, namely: Cr-Ti-V and Cr-Ti-Mn in respect of micro-hardness and wear resistance of carbide coatings obtained by thermo-chemical treatment of high carbon steel. «Composition - properties» diagrams have been plotted using mathematical models. Treatment with optimum compositions of powder media permits to increase wear resistance of steel by factor of 30-70 as compared with untreated steel. 

Ab initio study of the magnetic ordering in the semiconductors Mn{sub x}Ti{sub 1-x}O{sub 2}, Co{sub x}Ti{sub 1-x}O{sub 2} and Fe{sub x}Ti{sub 1-x}O{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Errico, L.A. [Departamento de Fisica, Facultad de Ciencias Exactas, Universidad Nacional de La Plata, C.C. 67, 1900, La Plata (Argentina)]. E-mail: errico@fisica.unlp.edu.ar; Weissmann, M. [Departamento de Fisica, Comision Nacional de Energia Atomica, Avda. del Libertador 8250, 1429 Buenos Aires (Argentina); Renteria, M. [Departamento de Fisica, Facultad de Ciencias Exactas, Universidad Nacional de La Plata, C.C. 67, 1900, La Plata (Argentina)

2004-12-31

In this work we present a set of density-functional-theory calculations in the systems Mn{sub x}Ti{sub 1-x}O{sub 2}, Fe{sub x}Ti{sub 1-x}O{sub 2}, and Co{sub x}Ti{sub 1-x}O{sub 2}. The calculations were performed with the full-potential linearized augmented plane wave method, assuming that the magnetic impurities substitutionally replace the Ti ions and considering different distributions of them in the host lattice. Our results show that the system Co{sub x}Ti{sub 1-x}O{sub 2} is ferromagnetic, while Mn{sub x}Ti{sub 1-x}O{sub 2} is antiferromagnetic. In both cases, this is independent of the distribution of the impurities in the TiO{sub 2} lattice. First results obtained in the system Fe{sub x}Ti{sub 1-x}O{sub 2} are also presented.

Influence of elemental diffusion on low temperature formation of MgH2 in TiMn1.3T0.2-Mg (T = 3d-transition elements)

International Nuclear Information System (INIS)

Yamamoto, K.; Tanioka, S.; Tsushio, Y.; Shimizu, T.; Morishita, T.; Orimo, S.; Fujii, H.

1996-01-01

In order to examine the influence of the elemental diffusion from the host compound into the Mg region on low temperature formation of MgH 2 , we have investigated the hydriding properties and the microstructures of the composite materials TiMn 1.3 T 0.2 -Mg (T = V, Cr, Mn, Fe, Co, Ni and Cu). MgH 2 is formed at 353 K in all composite materials. Of all the substitutions, the amount of MgH 2 is the largest in the case of the Cu substitution, which originates from the existence of the Mg-Mg 2 Cu eutectic formed by Cu diffusion from the host compound TiMn 1.3 Cu 0.2 into the Mg region during the liquid phase sintering. In addition, the hydrogen capacity of TiMn 1.3 Cu 0.2 -Mg (that is TiMn 1.3 Cu 0.1 -(Mg+Mg 2 Cu) after the sintering) easily saturates in comparison with TiMn 1.5 -(Mg+Mg 2 Cu) without Cu diffusion. It is concluded that Cu diffusion promotes the mobility of hydrogen atoms at the complex interface between the host compound and the Mg region. (orig.)

Electron diffraction and microscopy study of the structure and microstructure of the hexagonal perovskite Ba3Ti2MnO9

International Nuclear Information System (INIS)

Maunders, C.

2007-01-01

This paper reports a structural and microstructural investigation of the hexagonal perovskite Ba 3 Ti 2 MnO 9 using electron microscopy and diffraction. Convergent-beam electron diffraction (CBED) revealed the structure has the noncentrosymmetric space group P6 3 mc (186) at room temperature and at ∝ 110 K. Compared with the centrosymmetric parent structure BaTiO 3 , with space group P6 3 /mmc, this represents a break in mirror symmetry normal to the c axis. This implies the Ti and Mn atoms are ordered on alternate octahedral sites along the left angle 0001 right angle direction in Ba 3 Ti 2 MnO 9 . Using high-resolution electron microscopy (HREM), we observed occasional 6H/12R interfaces on (0001) planes, however, no antiphase boundaries were observed, as were seen in Ba 3 Ti 2 RuO 9 . Using powder X-ray Rietveld refinement we have measured the lattice parameters from polycrystalline samples to be a=5.6880±0.0005, c=13.9223±0.0015 Aa at room temperature. (orig.)

Magneto-electric properties and magnetic entropy change in perovskite La{sub 0.7}Sr{sub 0.3}Mn{sub 1−x}Ti{sub x}O{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Bau, Le Viet, E-mail: levietbau@hdu.edu.vn; An, Nguyen Manh

2016-12-15

The ceramic samples of La{sub 0.7}Sr{sub 0.3}Mn{sub 1−x}Ti{sub x}O{sub 3}(x=0; 0.05; 0.1; 0.2 and 0.3) were synthesized by the conventional solid state reaction method. Their electric, magnetic and magnetocaloric properties have been investigated. The transition temperature declines and a significant influence on the width of the ferro-paramagnetic phase transition is observed as increasing Ti concentration. Moreover, the sign of spin-glass is expected to exist in the high concentration samples. For fully replacing Ti{sup 4+} for Mn{sup 4+}, the canted spin state is formed. The substitution Ti for Mn increases resistivity quickly and the insulating–metallic transition temperature shifts toward lower temperature. For x>0.1 samples, the insulating state is observed even in ferromagnetic phase. The substitution Ti shifts the CME to room temperature while almost persists the value of entropy change. Although the maximum value of CME reduces slightly, the temperature range happening MCE is expended and then improves the relative cooling power. These properties could be explained in term of DE interaction and phase separation phenomenon. - Highlights: • Electro-magnetic properties and CME of La{sub 0.7}Sr{sub 0.3}Mn{sub 1-x}Ti{sub x}O{sub 3} have been investigated. • T{sub C} declines and the width of the F-M phase transition is observed as increasing Ti concentration. • For fully replacing Ti{sup 4+} for Mn{sup 4+}, the canted spin state is formed. • The substitution Ti for Mn increases resistivity quickly and T{sub P} shifts toward lower temperature. • The substitution Ti shifts CME to 300 K while almost persists the value of entropy change. • Relative cooling power (RCP) increases with substitution 5% Ti for Mn.

Influence of Copper on the Hot Ductility of 20CrMnTi Steel

Science.gov (United States)

Peng, Hong-bing; Chen, Wei-qing; Chen, Lie; Guo, Dong

2015-02-01

The hot ductility of 20CrMnTi steel with x% copper (x = 0, 0.34) was investigated. Results show that copper can reduce its hot ductility, but there is no significant copper-segregation at the boundary tested by EPMA. The average copper content at grain boundaries and substrate is 0.352% and 0.318% respectively in steel containing 0.34% copper tensile-tested at 950 °C. The fracture morphology was examined with SEM and many small and shallow dimples were found on the fracture of steel with copper, and fine copper sulfide was found from carbon extraction replicas using TEM. Additionally, adding 0.34% copper caused an increase in the dynamic recrystallization temperature from 950 °C to 1000 °C, which indicates that copper can retard the dynamic recrystallization (DRX) of austenite. The detrimental influence of copper on hot ductility of 20CrMnTi steel is due mainly to the fine copper sulfide in the steel and its retarding the DRX.

Ab initio study of domain structures in half-metallic CoTi{sub 1−x}Mn{sub x}Sb and thermoelectric CoTi{sub 1−x}Sc{sub x}Sb half-Heusler alloys

Energy Technology Data Exchange (ETDEWEB)

Miranda Mena, Joaquin, E-mail: joaquin.miranda@uni-bayreuth.de; Schoberth, Heiko G.; Gruhn, Thomas; Emmerich, Heike

2015-11-25

We present first-principles calculations of the electronic density of state, the structures in CoTi{sub 1−x}Sc{sub x}Sb and CoTi{sub 1−x}Mn{sub x}Sb. In addition for the latter we calculate magnetic moments. Systems with different stoichiometries are compared and low energy configurations are determined using a cluster expansion procedure. For all studied manganese concentrations, x > 0, CoTi{sub 1−x}Mn{sub x}Sb is half-metallic and magnetic, which make it interesting for spintronic applications. In contrast, with increasing scandium concentration, the band gap of CoTi{sub x}Sc{sub 1-x}Sb closes continuously, while the material changes from a semiconductor to a non-magnetic metal. For low Sc doping this material is well suited for thermoelectric applications. The electronic states close to the Fermi energy are strongly influenced by the distribution of Ti and Mn (or Ti and Sc). This has important consequences for the usage of materials in application fields like spintronics and thermoelectrics. In general, a phase separation of the alloys into a Ti rich and a Ti poor phase is energetically favored. Using mean field theory we create a phase diagram that shows the coexistence and the spinodal region. A spontaneous demixing can be used for the creation of nanodomains within the material. In the case of CoTi{sub 1−x}Sc{sub x}Sb, the resulting reduced lattice thermal conductivity is beneficial for thermoelectric applications, while in CoTi{sub 1−x}Mn{sub x}Sb the nanodomains are detrimental for polarization.

Quantifying Local and Cooperative Components in the Ferroelectric Distortion of BaTiO3: Learning from the Off-Center Motion in the MnCl65– Complex Formed in KCl:Mn+

DEFF Research Database (Denmark)

García Lastra, Juan Maria; García-Fernández, P.; Calle-Vallejo, F.

2014-01-01

→ C4v → Oh local transformations occurring in the 10–50 K temperature range for the MnCl65– complex formed in KCl:Mn+ that mimic the behavior of BaTiO3. From Boltzmann analysis of the vibronic levels derived from ab initio calculations and considering decoherence introduced by random strains......, the present calculations reproduce the experimental phase sequence and transition temperatures. Furthermore, our calculations show that the off-center instability in KCl:Mn+ would be suppressed by reducing by only 1% the lattice parameter, a situation that then becomes comparable to that found for BaTiO3...

Au and Pd nanoparticles supported on CeO{sub 2}, TiO{sub 2}, and Mn{sub 2}O{sub 3} oxides

Energy Technology Data Exchange (ETDEWEB)

Nascente, P.A.P., E-mail: nascente@ufscar.br [Federal University of Sao Carlos, Department of Materials Engineering, Sao Carlos, SP (Brazil); Maluf, S.S.; Afonso, C.R.M. [Federal University of Sao Carlos, Department of Materials Engineering, Sao Carlos, SP (Brazil); Landers, R. [State University of Campinas, Institute of Physics, Department of Applied Physics, Campinas, SP (Brazil); Pinheiro, A.N.; Leite, E.R. [Federal University of Sao Carlos, Department of Chemistry, Sao Carlos, SP (Brazil)

2014-10-01

Highlights: • CeO{sub 2}, TiO{sub 2}, and Mn{sub 2}O{sub 3} supported Au and Pd nanoparticles. • Additions of 0.5 wt% of Au and Pd onto CeO{sub 2}, TiO{sub 2}, and Mn{sub 2}O{sub 3} supports. • Characterization by XRD, XPS, EDS, TEM, HRTEM, STEM, and EFTEM. - Abstract: Gold and palladium nanoparticles were incorporated on CeO{sub 2}, TiO{sub 2}, and Mn{sub 2}O{sub 3} supports prepared by a sol–gel method. The samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), high resolution TEM (HRTEM), scanning TEM (STEM) in high angle annular dark field mode (HAADF), and energy filtered TEM (EFTEM) using electron energy loss spectroscopy (EELS). The XRD diffractograms presented sharp and intense peaks indicating that the samples are highly crystalline, but it did not detected any peak corresponding to Au or Pd phases. This indicates that the Au and Pd NPs were incorporated into the structures of the oxides. It was not possible to obtain an Au 4f spectrum for Au/Mn{sub 2}O{sub 3} due to an overlap with the Mn 3p spectrum. The XPS Au 4f spectra for Au/CeO{sub 2} and Au/TiO{sub 2} present negative chemical shifts that could be attributed to particle-size-related properties. The XPS Pd 3d spectra indicate that for both CeO{sub 2} and TiO{sub 2} substrates, the Pd NPs were in the metallic state, while for the Mn{sub 2}O{sub 3} substrate, the Pd NPs were oxidized. The HRTEM results show the formation of nanocrystalline oxides having particles sizes between 50 and 200 nm. TEM micrographs show that the addition of Au caused the formation of Au clusters in between the CeO{sub 2} NPS, formation of Au NPs for the TiO{sub 2} support, and homogeneous distribution of Au clusters for the Mn{sub 2}O{sub 3} support. The addition of Pd yielded a homogeneous dispersion throughout the CeO{sub 2} and TiO{sub 2}, but caused the formation of Pd clusters for the Mn{sub 2}O

Deposition of Li{sub 4}Ti{sub 5}O{sub 12} and LiMn{sub 2}O{sub 4} films on the lithium-ion conductor of Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} sintered pellet

Energy Technology Data Exchange (ETDEWEB)

Wu, Xian Ming, E-mail: xianmingwu@163.com [College of Chemistry and Chemical Engineering, Jishou University, Jishou Hunan 416000 (China); Xiangxi Minerals and New Materials Research and Service Center, Jishou Hunan 416000 (China); Chen, Shang [College of Chemistry and Chemical Engineering, Jishou University, Jishou Hunan 416000 (China); Xiangxi Minerals and New Materials Research and Service Center, Jishou Hunan 416000 (China); He, Ze Qiang; Chen, Shou Bin; Li, Run Xiu [College of Chemistry and Chemical Engineering, Jishou University, Jishou Hunan 416000 (China)

2015-08-31

LiMn{sub 2}O{sub 4} and Li{sub 4}Ti{sub 5}O{sub 12} films were deposited on the lithium-ion conductor of Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} sintered pellet by spray technique. The effect of annealing temperature, annealing time, Li:Ti and Li:Mn molar ratio on the phase and crystallization of the films were investigated with X-ray diffraction. The LiMn{sub 2}O{sub 4}/Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3}/Li{sub 4}Ti{sub 5}O{sub 12} thin-film lithium-ion battery using Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} sintered pellet as both electrolyte and substrate was also studied. The results show that the effect of annealing temperature, annealing time, Li:Ti and Li:Mn molar ratio has great effect on the phase and crystallization of Li{sub 4}Ti{sub 5}O{sub 12} and LiMn{sub 2}O{sub 4} films deposited on the Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} sintered pellet. The optimal Li:Ti and Li:Mn molar ratio for the deposition of Li{sub 4}Ti{sub 5}O{sub 12} and LiMn{sub 2}O{sub 4} films on Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} sintered pellet are 7.2:5 and 1.05:2, respectively. The optimal annealing temperature and time for the deposition of LiMn{sub 2}O{sub 4} film on Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} sintered pellet are 650 °C and 10 min. While those for Li{sub 4}Ti{sub 5}O{sub 12} film are 700 °C and 10 min. The LiMn{sub 2}O{sub 4}/Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3}/Li{sub 4}Ti{sub 5}O{sub 12} thin-film battery offers a working voltage about 2.25 V and can be easily cycled. - Highlights: • LiMn{sub 2}O{sub 4} and Li{sub 4}Ti{sub 5}O{sub 12} films spray deposited on Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} sintered pellet • Film crystal phase depends on the spray solution composition and annealing conditions. • Prepared thin-film lithium-ion battery employs sintered pellet as electrolyte and substrate. • LiMn{sub 2}O{sub 4}/Li{sub 1.3}Al{sub 0.3}Ti{sub 1

Characterization of Sumbawa manganese ore and recovery of manganese sulfate as leaching products

Science.gov (United States)

Kusumaningrum, Retno; Rahmani, Siti Astari; Widayatno, Wahyu Bambang; Wismogroho, Agus Sukarto; Nugroho, Dwi Wahyu; Maulana, Syahrizal; Rochman, Nurul Taufiqu; Amal, M. Ikhlasul

2018-05-01

The aims of this research were to study the leaching process of manganese ore which originated from Sumbawa, Indonesia and its characterization. A high grade Indonesian manganese ore from Sumbawa, West of Nusa Tenggara was characterized by X-Ray Fluorescence (XRF). The result showed composition of 78.8 % Mn, 17.77% Fe and the rest were trace elements such as Si, Co, Ti, Zn, V and Zr contents. X-Ray Diffraction analysis showed that the manganese ore was consisted of pyrolusite (MnO2), rhodonite (MnSiO3), rhodochrosite (MnCO3) and hematite (Fe2O3). Manganese ore was also analyzed by thermal analysis to observe their thermal decomposition character. In this study, sulphuric acid (H2SO4, 6 M) was deployed as leaching agent. The leaching process was performed at 90 °C for two hours with the addition of NH4OH to control pH. Recovery percentage of leaching process yielded of 87 % Mn extracted. The crystallization process result at heating temperature of 200 °C was confirmed by XRD as manganese sulfate.

TiO₂ Surface Coating of Mn-Zn Dopped Ferrites Study

DEFF Research Database (Denmark)

Solný, Tomáš; Ptacek, Petr; Másilko, Jiří

2016-01-01

This study deals with TiO2 coating of powder Mn-Zn ferrite in order to recieve photocatalytic layer on the top of these particles, forming core-shell catalyst. Powder catalysts are of great advance over the world due to the high surface area, considering the kinetics proceeds through heterogenous...... phase boundary catalysis. However their withdrawal from cleaning systems often requires energetically and economically demanding processes such as filtration and ultrafiltration. Since the ferrite is magnetic, the advantage of such formed core-shell photocatalyst is easibility of removing from...... photocatalytic decomposition system using external magnetic field. In this study the surface coating is performed, using Ti alkoxides mixtures with nanosized TiO2 particles and C and Au coating to form film layer of TiO2 on the surface of ferrite. XRD, SEM – EDS analyses are employed to study surface coating....

Dielectric properties of Mn doped SrTiO.sub.3./sub..

Czech Academy of Sciences Publication Activity Database

Savinov, Maxim; Trepakov, Vladimír; Syrnikov, P. P.; Železný, Vladimír; Pokorný, Jan; Deyneka, Alexander; Jastrabík, Lubomír; Galinetto, P.

2008-01-01

Roč. 20, - (2008), 095221/1-095221/6 ISSN 0953-8984 R&D Projects: GA AV ČR KAN301370701; GA AV ČR 1QS100100563; GA MŠk(CZ) 1M06002 Institutional research plan: CEZ:AV0Z10100522; CEZ:AV0Z10100521 Keywords : dielectric permittivity * IR reflectivity * SrTiO3:Mn Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.900, year: 2008

The direct synthesis of mesoporous structured MnO2/TiO2 nanocomposite: a novel visible-light active photocatalyst with large pore size

Science.gov (United States)

Xue, Min; Huang, Li; Wang, Jian-Qiang; Wang, Ying; Gao, Ling; Zhu, Jian-hua; Zou, Zhi-Gang

2008-05-01

A series of visible-light-driven mesoporous structured MnO2/TiO2 nanocrystal photocatalysts have been synthesized through a modified sol-gel method, and the N2 adsorption-desorption isotherm confirms that the mesoporous materials possess large pore size (up to 9.2 nm) and a narrow pore size distribution. X-ray powder diffraction (XRD) analyses and complementary x-ray photoelectron spectroscopy (XPS) measurements reveal that the doping of the transition metal Mn inhibits the growth of TiO2 anatase nanocrystals and the Mn species are highly dispersed on the surface of TiO2. The ultraviolet (UV)-vis spectrum demonstrates the excellent adsorption properties of MnO2/TiO2 over the whole region of visible light, which enables this novel photocatalysis material to possess remarkable activity in the photocatalytic degradation of methylene blue under visible light radiation. Moreover, a 'coating mechanism' based on the nucleation of titania nanocrystals along with the interaction between the dopant precursors and titania clusters has been suggested.

The direct synthesis of mesoporous structured MnO2/TiO2 nanocomposite: a novel visible-light active photocatalyst with large pore size

International Nuclear Information System (INIS)

Xue Min; Huang Li; Wang Jianqiang; Wang Ying; Zou Zhigang; Gao Ling; Zhu Jianhua

2008-01-01

A series of visible-light-driven mesoporous structured MnO 2 /TiO 2 nanocrystal photocatalysts have been synthesized through a modified sol-gel method, and the N 2 adsorption-desorption isotherm confirms that the mesoporous materials possess large pore size (up to 9.2 nm) and a narrow pore size distribution. X-ray powder diffraction (XRD) analyses and complementary x-ray photoelectron spectroscopy (XPS) measurements reveal that the doping of the transition metal Mn inhibits the growth of TiO 2 anatase nanocrystals and the Mn species are highly dispersed on the surface of TiO 2 . The ultraviolet (UV)-vis spectrum demonstrates the excellent adsorption properties of MnO 2 /TiO 2 over the whole region of visible light, which enables this novel photocatalysis material to possess remarkable activity in the photocatalytic degradation of methylene blue under visible light radiation. Moreover, a 'coating mechanism' based on the nucleation of titania nanocrystals along with the interaction between the dopant precursors and titania clusters has been suggested

The influence of the oxygen partial pressure on the quasi-ternary system Cr-Mn-Ti-oxide

International Nuclear Information System (INIS)

Garcia-Rosales, C.; Schulze, H.A.; Naoumidis, A.; Nickel, H.

1991-05-01

The passivation layers formed by the oxidizing corrosion of high temperature alloys consist primarily of oxides and mixed oxides of the elements chromium, manganese and titanium. For a reproducible formation and characterization of such oxide layers it is necessary to know the phase equilibria of these oxide systems at temperature and oxygen partial pressure conditions which will be relevant during their application. For the investigation of the quasi-ternary system Cr-Mn-Ti-oxide, oxide powders were prepared and annealed at 1000deg C under different oxygen partial pressures ranging from 0.21 bar to 10 -21 bar. Phase identification and determination of lattice parameter using X-ray diffraction analysis as well as the direct measurement of phase boundaries as a function of oxygen partial pressure using the emf-methode were carried out for these investigations. In the quasi-ternary system Cr-Mn-Ti-oxide the spinels play a decisive role in the oxigen partial pressure range examined. The spinel MnCr 2 O 4 may be regarded as the most significant compound. Part of the chronium can be replaced by trivalent manganese at high oxygen partial pressures and by trivalent titanium at low pressures, and the formation of a solid solution with the spinel Mn 2 TiO 4 is possible in all cases. In this way a coherent single-phase spinel region is observed which extends over the entire oxygen partial pressure range form 0.21 bar to 10 -21 bar examined at 1000deg C. (orig.) [de

Characterization and Catalytic Activity of Mn-Co/TiO2 Catalysts for NO Oxidation to NO2 at Low Temperature

Directory of Open Access Journals (Sweden)

Lu Qiu

2016-01-01

Full Text Available A series of Mn-Co/TiO2 catalysts were prepared by wet impregnation method and evaluated for the oxidation of NO to NO2. The effects of Co amounts and calcination temperature on NO oxidation were investigated in detail. The catalytic oxidation ability in the temperature range of 403–473 K was obviously improved by doping cobalt into Mn/TiO2. These samples were characterized by nitrogen adsorption-desorption, X-ray diffraction (XRD, X-ray photoelectron spectroscopy (XPS, transmission electron microscope (TEM and hydrogen temperature programmed reduction (H2-TPR. The results indicated that the formation of dispersed Co3O4·CoMnO3 mixed oxides through synergistic interaction between Mn-O and Co-O was directly responsible for the enhanced activities towards NO oxidation at low temperatures. Doping of Co enhanced Mn4+ formation and increased chemical adsorbed oxygen amounts, which also accelerated NO oxidation.

Favorable ultraviolet photoelectric effects in TbMnO3/Nb-SrTiO3 heterostructures

KAUST Repository

Jin, Kexin; Zhai, Y. X.; Li, Hui; Tian, Y. F.; Luo, B. C.; Wu, Tao

2014-01-01

The rectifying properties and ultraviolet photoelectric effects in TbMnO3/Nb-doped SrTiO3 heterostructures have been investigated. The ideality factors and the diffusion voltages obtained from the current-voltage curves nonlinearly decrease

Electrochemical activity of Li{sub 2}FeTiO{sub 4} and Li{sub 2}MnTiO{sub 4} as potential active materials for Li ion batteries: A comparison with Li{sub 2}NiTiO{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Kuezma, Mirjana; Dominko, Robert; Bele, Marjan; Jamnik, Janko [National Institute of Chemistry, Ljubljana (Slovenia); Meden, Anton [Faculty of Chemistry and Chemical Technology, University of Ljubljana (Slovenia); Makovec, Darko [Jozef Stefan Institute, Ljubljana (Slovenia); Gaberscek, Miran [National Institute of Chemistry, Ljubljana (Slovenia); Faculty of Chemistry and Chemical Technology, University of Ljubljana (Slovenia)

2009-04-01

We demonstrate, for the first time, a considerable electrochemical activity of two members of lithium transition element titanates: Li{sub 2}FeTiO{sub 4} and Li{sub 2}MnTiO{sub 4}. Both materials consist of 10-20 nm particles embedded in a conductive carbon coating. We show that not the coating but the small particle size is decisive for materials' activity. Li{sub 2}FeTiO{sub 4} shows a stable reversible capacity of up to 123 mA hg{sup -1} at C/20 and 60 C which is 83% of the theoretical value for exchange of 1 electron (148 mA hg{sup -1}). Li{sub 2}MnTiO{sub 4} could only be prepared in a nanosized form that contained about 30% of impurities. The capacity of the whole material (including impurities) is comparable to that of Li{sub 2}FeTiO{sub 4} but the cycling stability is much poorer. In contrast to the Fe and Mn analogues, the third member of the titanate family, Li{sub 2}NiTiO{sub 4}, shows a good electrochemistry even when the particle size is much larger (about 100 nm). During initial cycles at C/10 and 60 C, exchange of more than 1 electron per compound formula has been observed. The cycling stability at high temperatures, however, is poor. (author)

Effect of Tin, Copper and Boron on the Hot Ductility of 20CrMnTi Steel between 650 °C and 1100 °C

Science.gov (United States)

Peng, Hong-bing; Chen, Wei-qing; Chen, Lie; Guo, Dong

2015-02-01

The hot ductility of 20CrMnTi steel with x% tin, y% copper and z ppm boron (x = 0, 0.02; y = 0, 0.2; z = 0, 60) was investigated. The results show that tin and copper in 20CrMnTi steel are detrimental to its hot ductility while adding boron can eliminate the adverse effect and enhance hot ductility greatly. Tin is found to segregate to the boundaries tested by EPMA in 20CrMnTi steel containing tin and copper and tin-segregation is suppressed by adding boron, moreover, copper was found not to segregate to boundaries, however, fine copper sulfide was found from carbon extraction replicas using TEM. The adverse effect of tin and copper on the hot ductility was due mainly to tin segregation and fine copper sulfide in the steel. The proeutectoid ferrite film precipitating along the austenite grain boundary causes the ductility trough of the three examined steels. Tin and copper in 20CrMnTi steel can retard the occurrence of dynamic recrystallization (DRX) while boron-addition can compensate for that change. The beneficial effect of boron on 20CrMnTi steel containing tin and copper might be ascribed to the fact that boron segregates to grain boundaries, accelerates onset of DRX, retards austenite/ferrite transformation and promotes intragranular nucleation of ferrite.

Non-enzymatic detection of glucose in fruits using TiO2-Mn3O4 hybrid nano interface

Science.gov (United States)

Jayanth Babu, K.; Sasya, Madhurantakam; Nesakumar, Noel; Shankar, Prabakaran; Gumpu, Manju Bhargavi; Ramachandra, Bhat Lakshmishri; Kulandaisamy, Arockia Jayalatha; Rayappan, John Bosco Balaguru

2017-08-01

Consumption of fruits leads to increase in glucose level in blood for diabetic patients, which in turn leads to peripheral, vascular, ocular complications and cardiac diseases. In this context, a non-enzymatic hybrid glucose biosensor was fabricated for the first time to detect glucose by immobilizing titanium oxide-manganese oxide (TiO2-Mn3O4) nanocomposite and chitosan membrane on to the surface of Pt working electrode (Pt/TiO2-Mn3O4/chitosan). TiO2-Mn3O4 nanocomposite catalyzed the oxidation of glucose to gluconolactone in the absence of glucose oxidase enzyme with high electron transfer rate, good biocompatibility and large surface coverage. Electrochemical measurements revealed the excellent sensing response of the developed biosensor towards glucose with a high sensitivity of 7.073 µA mM-1, linearity of 0.01-0.1 mM, low detection limit of 0.01 µM, reproducibility of 1.5% and stability of 98.8%. The electrochemical parameters estimated from the anodic process were subjected to linear regression models for the detection of unknown concentration of glucose in different fruit samples.

Leakage current phenomena in Mn-doped Bi(Na,K)TiO_3-based ferroelectric thin films

International Nuclear Information System (INIS)

Walenza-Slabe, J.; Gibbons, B. J.

2016-01-01

Mn-doped 80(Bi_0_._5Na_0_._5)TiO_3-20(Bi_0_._5K_0_._5)TiO_3 thin films were fabricated by chemical solution deposition on Pt/TiO_2/SiO_2/Si substrates. Steady state and time-dependent leakage current were investigated from room temperature to 180 °C. Undoped and low-doped films showed space-charge-limited current (SCLC) at high temperatures. The electric field marking the transition from Ohmic to trap-filling-limited current increased monotonically with Mn-doping. With 2 mol. % Mn, the current was Ohmic up to 430 kV/cm, even at 180 °C. Modeling of the SCLC showed that all films exhibited shallow trap levels and high trap concentrations. In the regime of steady state leakage, there were also observations of negative differential resistivity and positive temperature coefficient of resistivity near room temperature. Both of these phenomena were confined to relatively low temperatures (below ∼60 °C). Transient currents were observed in the time-dependent leakage data, which was measured out to several hundred seconds. In the undoped films, these were found to be a consequence of oxygen vacancy migration modulating the electronic conductivity. The mobility and thermal activation energy for oxygen vacancies was extracted as μ_i_o_n ≈ 1.7 × 10"−"1"2 cm"2 V"−"1 s"−"1 and E_A_,_i_o_n ≈ 0.92 eV, respectively. The transient current displayed different characteristics in the 1 mol. % Mn-doped films which were not readily explained by oxygen vacancy migration.

Magnetic, Electrical Transport and Impedance Spectroscopy Studies on Ti Substituted La0.67Sr0.33MnO3 Ceramics

International Nuclear Information System (INIS)

Zalita, Z.; Halim, S.A.; Lim, K.P.; Talib, Z.A.; Hishamuddin, Z.; Walter, C.P.

2009-01-01

La 0.67 Sr 0.33 Mn 1-x Ti x O 3 samples with x = 0.0, 0.2, 0.4 and 0.6 have been prepared using the conventional solid-state reaction method. The structure, magnetic and electrical transport properties as well as the impedance spectroscopy of the samples were investigated. The powder XRD analysis showed that all samples were single phase with rhombohedral perovskite structure. The magnetization curve suggests that the Ti substituted samples exhibit weak ferromagnetic behaviour. The highest magnetoresistance (MR) value was obtained for sample x = 0.2 at temperature 200 K and field 1 T, which was 32.5 %. Low field magnetoresistance (LFMR) effect was observed for the x = 0.0 sample. The metal-like resistivity curve for the x = 0.0 sample was best fitted with ρ = ρo + ρ2T2 equation, indicating the grain boundary effects and electron-electron scattering process contribution. Semiconductor-like transport behaviour was observed for the Ti substituted samples and can be fitted by variable range hopping (VRH) and small polaron hopping (SPH) mechanisms. The activation energy of the samples increased when the Ti composition increased. An equivalent circuit was proposed for the impedance plot with a series of two parallel RC circuits. The grain, grain boundary and electrode resistance values increased with Ti composition due to the reduction of the Mn 3+ / Mn 4+ ratio. (author)

Interrelation between domain structures and polarization switching in hybrid improper ferroelectric Ca3(Mn,Ti)2O7

Science.gov (United States)

Gao, Bin; Huang, Fei-Ting; Wang, Yazhong; Kim, Jae-Wook; Wang, Lihai; Lim, Seong-Joon; Cheong, Sang-Wook

2017-05-01

Ca3Mn2O7 and Ca3Ti2O7 have been proposed as the prototypical hybrid improper ferroelectrics (HIFs), and a significant magnetoelectric (ME) coupling in magnetic Ca3Mn2O7 is, in fact, reported theoretically and experimentally. Although the switchability of polarization is confirmed in Ca3Ti2O7 and other non-magnetic HIFs, there is no report of switchable polarization in the isostructural Ca3Mn2O7. We constructed the phase diagram of Ca3Mn2-xTixO7 through our systematic study of a series of single crystalline Ca3Mn2-xTixO7 (x = 0, 0.1, 1, 1.5, and 2). Using transmission electron microscopy, we have unveiled the unique domain structure of Ca3Mn2O7: the high-density 90° stacking of a- and b-domains along the c-axis due to the phase transition through an intermediate Acca phase and the in-plane irregular wavy ferroelastic twin domains. The interrelation between domain structures and physical properties is unprecedented: the stacking along the c-axis prevents the switching of polarization and causes the irregular in-plane ferroelastic domain pattern. In addition, we have determined the magnetic phase diagram and found complex magnetism of Ca3Mn2O7 with isotropic canted moments. These results lead to negligible observable ME coupling in Ca3Mn2O7 and guide us to explore multiferroics with large ME coupling.

Enhanced electrical and magnetic properties in La0.7Sr0.3MnO3 thin films deposited on CaTiO3-buffered silicon substrates

Directory of Open Access Journals (Sweden)

C. Adamo

2015-06-01

Full Text Available We investigate the suitability of an epitaxial CaTiO3 buffer layer deposited onto (100 Si by reactive molecular-beam epitaxy (MBE for the epitaxial integration of the colossal magnetoresistive material La0.7Sr0.3MnO3 with silicon. The magnetic and electrical properties of La0.7Sr0.3MnO3 films deposited by MBE on CaTiO3-buffered silicon (CaTiO3/Si are compared with those deposited on SrTiO3-buffered silicon (SrTiO3/Si. In addition to possessing a higher Curie temperature and a higher metal-to-insulator transition temperature, the electrical resistivity and 1/f noise level at 300 K are reduced by a factor of two in the heterostructure with the CaTiO3 buffer layer. These results are relevant to device applications of La0.7Sr0.3MnO3 thin films on silicon substrates.

Hybrid selective noncatalytic reduction (SNCR)/selective catalytic reduction (SCR) for NOx removal using low-temperature SCR with Mn-V2O5/TiO2 catalyst.

Science.gov (United States)

Choi, Sung-Woo; Choi, Sang-Ki; Bae, Hun-Kyun

2015-04-01

A hybrid selective noncatalytic reduction/selective catalytic reduction (SNCR/SCR) system that uses two types of technology, low-temperature SCR process and SNCR process, was designed to develop nitrogen oxide (NOx) reduction technology. SCR was conducted with space velocity (SV)=2400 hr(-1) and hybrid SNCR/SCR with SV=6000 hr(-1), since the study focused on reducing the amount of catalyst and both achieved 98% NOx reduction efficiency. Characteristics of NOx reduction by NH3 were studied for low-temperature SCR system at 150 °C using Mn-V2O5/TiO2 catalyst. Mn-added V2O5/TiO2 catalyst was produced, and selective catalyst reduction of NOx by NH3 was experimented. NOx reduction rate according to added Mn content in Mn-V2O5/TiO2 catalyst was studied with varying conditions of reaction temperature, normalized stoichiometric ratio (NSR), SV, and O2 concentration. In the catalyst experiment according to V2O5 concentration, 1 wt.% V2O5 catalyst showed the highest NOx reduction rate: 98% reduction at temperature window of 200~250 °C. As a promoter of the V2O5 catalyst, 5 wt.% Mn was added, and the catalyst showed 47~90% higher efficiency even with low temperatures, 100~200 °C. Mn-V2O5/TiO2 catalyst, prepared by adding 5 wt.% Mn in V2O5/TiO2 catalyst, showed increments of catalyst activation at 150 °C as well as NOx reduction. Mn-V2O5/TiO2 catalyst showed 8% higher rate for NOx reduction compared with V2O5/TiO2 catalyst in 150 °C SCR. Thus, (5 wt.%)Mn-(1 wt.%)V2O5/TiO2 catalyst was applied in SCR of hybrid SNCR/SCR system of low temperature at 150 °C. Low-temperature SCR hybrid SNCR/SCR (150 °C) system and hybrid SNCR/SCR (350 °C) showed 91~95% total reduction rate with conditions of SV=2400~6000 hr(-1) SCR and 850~1050 °C SNCR, NSR=1.5~2.0, and 5% O2. Hybrid SNCR/SCR (150 °C) system proved to be more effective than the hybrid SNCR/SCR (350 °C) system at low temperature. NOx control is very important, since they are the part of greenhouse gases as well as the

Kα X-ray satellite spectra of Ti, V, Cr and Mn induced by photons

Indian Academy of Sciences (India)

K X-ray emission spectra of Ti, V, Cr and Mn generated by photon excitation have been studied with a crystal spectrometer. The measured energy shifts of K satellite relative to the diagram line are compared with values obtained by electron excitation and with different theoretical estimates. The present experimental ...

Effect of Dopant Loading on the Structural and Catalytic Properties of Mn-Doped SrTiO3 Catalysts for Catalytic Soot Combustion

Directory of Open Access Journals (Sweden)

Santiago Iván Suárez-Vázquez

2018-02-01

Full Text Available Soot particles have been associated with respiratory diseases and cancer. To decrease these emissions, perovskite-mixed oxides have been proposed due to their thermal stability and redox surface properties. In this work, SrTiO3 doped with different amounts of Mn were synthesized by the hydrothermal method and tested for soot combustion. Results show that at low Mn content, structural distortion, and higher Oads/Olat ratio were observed which was attributed to the high content of Mn3+ in Ti sites. On the other hand, increasing the Mn content led to surface segregation of manganese oxide. All synthesized catalysts showed mesopores in the range of 32–47 nm. In the catalytic combustion of soot, the samples synthesized in this work lowered the combustion temperature by more than 100 °C compared with the uncatalyzed reaction. The sample doped with 1 wt % of Mn showed the best catalytic activity. The activation energy of these samples was also calculated, and the order of decreasing activation energy is as follows: uncatalyzed > Mn0 > Mn8 > Mn4 > Mn1. The best catalytic activity for Mn1 was attributed to its physicochemical properties and the mobility of the oxygen from the bulk to the surface at temperatures higher than 500 °C.

Mo, Mn and La doped TiO{sub 2}: Synthesis, characterization and photocatalytic activity for the decolourization of three different chromophoric dyes

Energy Technology Data Exchange (ETDEWEB)

Umar, K.; Haque, M.M. [Department of Chemistry, Aligarh Muslim University, Aligarh 202 002 (India); Muneer, M., E-mail: readermuneer@gmail.com [Department of Chemistry, Aligarh Muslim University, Aligarh 202 002 (India); Harada, T.; Matsumura, M. [Research Center for Solar Energy Chemistry, Osaka University, 1-3 Machikaneyama, Toyonaka 560-8531 (Japan)

2013-11-25

Highlights: •Detail study on synthesis, characterization and photocatalytic activity of doped-TiO{sub 2}. •SEM images indicates partial crystalline nature with rough surfaces. •The XRD analysis shows the partial crystalline nature and anatase phase. •The UV–Vis absorption spectra showed λ{sub max} shift towards longer wavelength. •TiO{sub 2} with dopant 0.75% (Mo), 1.0% (Mn, La) showed best photocatalytic efficiency. -- Abstract: Nanocrystalline TiO{sub 2} particles doped with different concentrations of Molybdenum (Mo), Manganese (Mn) and Lanthanum (La) (0.25–1.0%) were synthesized using sol–gel method and characterized by standard analytical techniques such as X-ray diffraction (XRD), UV–Vis spectroscopy and Scanning Electron Microscopy (SEM). The XRD analysis shows the partial crystalline nature and anatase phase. The SEM images of undoped and doped TiO{sub 2} at different magnifications also show the partial crystalline nature with rough surfaces. The photocatalytic activity of the synthesized particles (TiO{sub 2} doped with Mo, Mn and La) was tested by studying the decolourization of three different chromophoric dyes such as Acid Red 88 (azo dye), Gentian Violet (triphenylmethane dye) and Remazol Brilliant Blue R (anthraquinone dye) as a function of time on irradiation in aqueous suspension in an immersion well photochemical reactor with a 500 W halogen linear lamp in the presence of atmospheric oxygen. The results indicate that TiO{sub 2} with dopant concentration of 0.75% (Mo) and 1.0% (Mn, La) showed the highest photocatalytic activity as compared to the other dopant concentrations for the decolourization of all the dyes.

Effect of calcination temperature on the structure and performance of CeO{sub x}–MnO{sub x}/TiO{sub 2} nanoparticles for the catalytic combustion of chlorobenzene

Energy Technology Data Exchange (ETDEWEB)

He, Fei; Chen, Yong; Zhao, Pei; Liu, Shantang, E-mail: anliu123@hotmail.com [Wuhan Institute of Technology, Key Laboratory for Green Chemical Process of Ministry of Education, School of Chemistry and Environmental Engineering (China)

2016-05-15

In this study, MnO{sub x}/TiO{sub 2}, CeO{sub x}/TiO{sub 2}, and CeO{sub x}–MnO{sub x}/TiO{sub 2} catalysts were prepared by the homogeneous precipitation method. The effect of calcination temperature on the structure and catalytic performance of CeO{sub x}–MnO{sub x}/TiO{sub 2} mixed oxide catalyst in the catalytic combustion of chlorobenzene was investigated. The samples were characterized by X-ray diffraction, nitrogen adsorption–desorption, transmission electron microscopy, Raman spectra, hydrogen temperature-programmed reduction, and X-ray photoelectron spectroscopy. The results indicate that calcination significantly affect the activity of the prepared catalysts. When calcined at a low temperature such as 400 °C, Ce, and Mn species form a solid solution of MnCeO{sub x} in the catalyst, thus locating the O atoms in a perturbed chemical surrounding in the catalysts. This increases the mobility of the O atoms during the reaction, probably contributing to the highest catalytic activity of CeO{sub x}–MnO{sub x}/TiO{sub 2} among all the tested catalysts. However, a further increase in the calcination temperature decreased the performance of the catalyst for the catalytic combustion of chlorobenzene. This is probably because of a reduction in surface chemisorbed oxygen concentration, a decrease in the interface area between metal oxides and MnCeO{sub x} caused by the isolation of MnO{sub x} or CeO{sub 2} from MnCeO{sub x}, and a decrease in the specific surface area of CeO{sub x}–MnO{sub x}/TiO{sub 2} catalyst due to the sintering of catalyst.Graphical Abstract.

Effects of electron correlations application to Ti atoms on physical properties of (LaMnO{sub 3}){sub m}/(SrTiO{sub 3}){sub n} superlattices

Energy Technology Data Exchange (ETDEWEB)

Aezami, A., E-mail: a.aezami@gmail.com; Abolhassani, M.; Elahi, M.

2016-05-15

Magnetic structures and Curie temperatures of the (LaMnO{sub 3}){sub m}/(SrTiO{sub 3}){sub n} superlattices (SLm–n) with m=1, 2, 3 and n=1, 2, 3, 8 were investigated, using density functional theory implemented in Quantum-Espresso open source code. By applying on-site coulomb interaction (Hubbard term U) to Ti atoms for all of these superlattices, using Stoner–Wolfarth model, it was found that the magnetic order of interfacial atoms of these superlattices changed to ferromagnetic by implying U=5 eV on Ti atoms. The inclusion of electron–electron correlation with U=5 eV on the Ti atoms for all of the superlattices made the two dimensional electron gas (2DEG) formed at the interfaces, half-metallic. The obtained values of Curie temperature, calculated within mean field approximation with U=5 eV on the Ti atoms, are in good agreement with the experimental results. - Highlights: • Calculated the magnetic structure and Curie temperature of the (LaMnO{sub 3}){sub m}/(SrTiO{sub 3}){sub n} superlattices with m=1, 2, 3 and n=1, 2, 3, 8 by mean field approximation. • By implying U=5 eV on the Ti atoms, the magnetic order of interfacial atoms of these superlattices has changed to ferromagnetic. • The 2DEG formed at the interface half-metallic have made in these superlattices by the inclusion of electron-electron correlation with U=5 eV on the Ti atoms for all of the superlattices.

Effect of titanium on structure and martensitic transformation in rapidly solidified Cu-Al-Ni-Mn-Ti alloys

International Nuclear Information System (INIS)

Dutkiewicz, J.; Czeppe, T.; Morgiel, J.

1999-01-01

Alloys of composition Cu-(11.8-13.5)%Al-(3.2-4)%Ni-(2-3)%Mn and 0-1%Ti (wt.%) were cast using the melt spinning method in He atmosphere. Ribbons obtained in this process showed grains from 0.5 to 30 μm depending on the type of alloy and wheel speed. Bulk alloys and most of the ribbons contained mixed 18R and 2H type martensite at room temperature (RT). Some ribbons, crystallizing at the highest cooling rate, retained also β phase due to a drop of M s below RT. The M s temperatures in ribbons were strongly lowered with increasing wheel speed controlling the solidification rate. This drop of M s shows a linear relationship with d -1/2 , where d is grain size. The strongest decrease of M s and smallest grains were found in the ribbons containing titanium due to its grain refinement effect. The cubic Ti rich precipitates, present in both Cu-Al-Ni-Ti and Cu-Al-Ni-Mn-Ti bulk, were dispersed in ribbons cast with intermediate cooling rates of up to 26 m s -1 , but suppressed for higher cooling rates. The transformation hysteresis loop was much broader in ribbons due to presence of coherent Ti rich precipitates and differences in grain size which is particularly important in the ultra small grain size range. (orig.)

Evolution of a novel Si-18Mn-16Ti-11P alloy in Al-Si melt and its influence on microstructure and properties of high-Si Al-Si alloy

Directory of Open Access Journals (Sweden)

Xiao-Lu Zhou

Full Text Available A novel Si-18Mn-16Ti-11P master alloy has been developed to refine primary Si to 14.7 ± 1.3 μm, distributed uniformly in Al-27Si alloy. Comparing with traditional Cu-14P and Al-3P, Si-18Mn-16Ti-11P provided a much better refining effect, with in-situ highly active AlP. The refined Al-27Si alloy exhibited a CTE of 16.25 × 10−6/K which is slightly higher than that of Sip/Al composites fabricated by spray deposition. The UTS and elongation of refined Al-27Si alloy were increased by 106% and 235% comparing with those of unrefined alloy. It indicates that the novel Si-18Mn-16Ti-11P alloy is more suitable for high-Si Al-Si alloys and may be a candidate for refining hypereutectic Al-Si alloy for electronic packaging applications. Moreover, studies showed that TiP is the only P-containing phase in Si-18Mn-16Ti-11P master alloy. A core-shell reaction model was established to reveal mechanism of the transformation of TiP to AlP in Al-Si melts. The transformation is a liquid-solid diffusion reaction driven by chemical potential difference and the reaction rate is controlled by diffusion. It means sufficient holding time is necessary for Si-18Mn-16Ti-11P master alloy to achieve better refining effect. Keywords: Hypereutectic Al-Si alloy, Primary Si, Refinement, AlP, Thermal expansion behavior, Si-18Mn-16Ti-11P master alloy

Large recoverable electrostrain in Mn-doped (Ba,Sr) TiO3 ceramics

International Nuclear Information System (INIS)

Zhang, L.X.; Chen, W.; Ren, X.

2004-01-01

In this letter we demonstrate that with a different principle, BaTiO 3 ceramics, so far considered as inferior piezoelectrics compared with Pb(Zr,Ti)O 3 (PZT), can show a large recoverable electrostrain. This principle utilizes a point-defect-mediated reversible domain switching mechanism, which can in theory generate 0.368% strain for BaTiO 3 ceramics at the best condition. Experimental results showed that, after aging at room temperature, 1.0 mol % Mn-doped (Ba 0.95 Sr 0.05 )TiO 3 ceramics generate a large recoverable nonlinear strain of about 0.12%-0.15% at a field of 3 kV/mm. This value exceeds that of conventional hard PZT piezoelectric ceramics. A microscopic model for the domain-related electrostrain effect in ceramics is proposed. It is also found that the large electrostrain effect is quite stable with respect to both changing frequency and fatigue cycles. Large electrostrain remains recoverable down to 0.05 Hz and after 10 000 cycles. These results demonstrate the potential of our approach in achieving large recoverable electrostrain in environmental-friendly (Pb-free) ceramics

Robust electrodes based on coaxial TiC/C-MnO2 core/shell nanofiber arrays with excellent cycling stability for high-performance supercapacitors.

Science.gov (United States)

Zhang, Xuming; Peng, Xiang; Li, Wan; Li, Limin; Gao, Biao; Wu, Guosong; Huo, Kaifu; Chu, Paul K

2015-04-17

A coaxial electrode structure composed of manganese oxide-decorated TiC/C core/shell nanofiber arrays is produced hydrothermally in a KMnO4 solution. The pristine TiC/C core/shell structure prepared on the Ti alloy substrate provides the self-sacrificing carbon shell and highly conductive TiC core, thus greatly simplifying the fabrication process without requiring an additional reduction source and conductive additive. The as-prepared electrode exhibits a high specific capacitance of 645 F g(-1) at a discharging current density of 1 A g(-1) attributable to the highly conductive TiC/C and amorphous MnO2 shell with fast ion diffusion. In the charging/discharging cycling test, the as-prepared electrode shows high stability and 99% capacity retention after 5000 cycles. Although the thermal treatment conducted on the as-prepared electrode decreases the initial capacitance, the electrode undergoes capacitance recovery through structural transformation from the crystalline cluster to layered birnessite type MnO2 nanosheets as a result of dissolution and further electrodeposition in the cycling. 96.5% of the initial capacitance is retained after 1000 cycles at high charging/discharging current density of 25 A g(-1). This study demonstrates a novel scaffold to construct MnO2 based SCs with high specific capacitance as well as excellent mechanical and cycling stability boding well for future design of high-performance MnO2-based SCs. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hybrid improper ferroelectricity in Ruddlesden-Popper Ca{sub 3}(Ti,Mn){sub 2}O{sub 7} ceramics

Energy Technology Data Exchange (ETDEWEB)

Liu, X. Q., E-mail: xqliu@zju.edu.cn, E-mail: xmchen59@zju.edu.cn; Wu, J. W.; Shi, X. X.; Zhao, H. J.; Zhou, H. Y.; Chen, X. M., E-mail: xqliu@zju.edu.cn, E-mail: xmchen59@zju.edu.cn [Laboratory of Dielectric Materials, School of Materials Science and Engineering, Zhejiang University, 38 Zheda Road, Hangzhou 310027 (China); Qiu, R. H.; Zhang, W. Q. [Department of Physics, Shanghai University, 99 Shangda Road, Shanghai 200444 (China)

2015-05-18

The hybrid improper ferroelectricity (HIF) has been proposed as a promising way to create multiferroic materials with strong magnetoelectric coupling by the first-principle calculation, and the experimental evidences of HIF in Ruddlesden-Poper Ca{sub 3}(Ti{sub 1−x}Mn{sub x}){sub 2}O{sub 7} (x = 0, 0.05, 0.1, and 0.15) ceramics have been shown in the present work. The room temperature ferroelectric hysteresis loops are observed in these ceramics, and a polar orthorhombic structure with two oxygen tilting modes has been confirmed by the X-ray powder diffraction. A first-order phase transition around 1100 K in Ca{sub 3}Ti{sub 2}O{sub 7} was evidenced, and the temperatures of phase transitions decrease linearly with increasing of the contents of Mn{sup 4+} ions. Based on the result of first-principle calculations, the polarization should be reversed by switching through the mediated Amam phase in Ca{sub 3}Ti{sub 2}O{sub 7} ceramics.

The effects of Ni, Mo, Ti and Si on the mechanical properties of Cr free Mn steel (Fe-25Mn-5Al-2C)

International Nuclear Information System (INIS)

Schuon, S.R.

1982-01-01

The FeMnAlC alloys may hold potential as Cr-free replacements for high strategic material iron base superalloys, but little is known about their intermediate temperature (650 C to 870 C) mechanical properties. The effects of alloying elements on the mechanical properties of model FeMnAlC alloys were studied. Results showed that modified FeMnAlC alloys had promising short term, intermediate temperature properties but had relatively poor stress rupture lives at 172 MPa and 788 C. Room temperature and 788 C tensile strength of FeMnAlC alloys were better than common cast stainless steels. Changes in room temperature tensile and 788 C tensile strength and ductility, and 788 C stress rupture life were correlated with changes in Ni, Mo, Ti, and Si levels due to alloying effects on interstitial carbon levels and carbide morphology. Fe-25Mn-5Al-2C had a very poor stress rupture life at 172 MPa and 788 C. Addition of carbide-forming elements improved the stress rupture life

The electrochemical properties of Zr-Ti-V-Ni-Mn hydrogen storage alloys with various compositions for an electrode of Ni-MH secondary battery

Energy Technology Data Exchange (ETDEWEB)

Choi, Seung Jun; Jung, So Yi; Park, Choong Nyeon [Dept. of Metallurgical Engineering, Chonnam National University, Kwangju (Korea)

1999-12-01

Effects of alloy modification for the Zr{sub 0.7}Ti{sub 0.3}V{sub 0.4}Ni{sub 1.2}Mn{sub 0.4} alloy as an electrode materials have been investigated. When Ti in the alloy was partially substituted by Zr, the hydrogen storage capacity and subsequently the discharge capacity increased significantly, however, the activation characteristic and rate capability decreased. By substituting Mn with other elements (Cr, Co and Fe) in the alloy, discharge capacity decreased but the cycle life and rate capability were improved. Considering both the discharge capacity, the high rate discharge property and cycle life, the Zaire.{sub 7}Ti{sub 0.3}V{sub 0.4}Ni{sub 1.2}Mn{sub 0.3}Cr{sub 0.1} alloy among the alloys subjected to the test was found to be a prominent alloy for a practical usage. 11 refs., 5 figs., 2 tabs.

Effect of metal ions doping (M = Ti4+, Sn4+) on the catalytic performance of MnOx/CeO2 catalyst for low temperature selective catalytic reduction of NO with NH3

Science.gov (United States)

Xiong, Yan; Tang, Changjin; Dong, Lin

2015-04-01

Key Laboratory of Mesoscopic Chemistry of MOE, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210093, PR China The abatement of nitrogen oxides (NOx) emission from exhaust gases of diesel and stationary sources is a significant challenge for economic and social development. Ceria-based solid solutions were synthesized and used as supports to prepare MnOx/Ce0.8Ti0.2O2 and MnOx/Ce0.8Sn0.2O2 catalysts (Mn/CeTi and Mn/CeSn) for low temperature selective catalytic reduction of NO by NH3 (NH3-SCR). The effects of Ti or Sn doping on the catalytic performance of MnOx/CeO2 catalyst were investigated. Experimental results show that doping of Ti or Sn increases the NO removal efficiency of MnOx/CeO2. The NO conversion of Mn/CeTi catalyst is more than 90 % at temperature window of 175 ~ 300 °C under a gas hour space velocity of 60,000 mL.g-1.h-1. Modified catalysts are also found to exhibit greatly improved resistance to sulfur-poisoning. NH3-TPD results suggest that NH3 desorption on the catalysts is observed over a wide temperature range, due to the variability of adsorbed NH3 species with different thermal stabilities. Doping of Ti and Sn into Mn/CeO2 greatly increased the NH3 adsorption ability of the composites which could promote the SCR reaction. Characterization results also indicate that doping of Ti or Sn brings about catalysts with higher BET surface area, enhanced oxygen storage capacity and increased surface acidity.

Tunable magnetocaloric effect in Sr{sub 1-x}Ca{sub x}Mn{sub 0.5}Ti{sub 0.5}O{sub 3} perovskites

Energy Technology Data Exchange (ETDEWEB)

Shanmugapriya, K.; Palanivel, Balan [Pondicherry Engineering College, Department of Physics, Puducherry (India); Radheep, D.M.; Murugan, Ramaswamy [Pondicherry University, Department of Physics, Puducherry (India)

2017-07-15

Sr{sub 1-x}Ca{sub x}Mn{sub 0.5}Ti{sub 0.5}O{sub 3} (x = 0.25, 0.5 and 0.75) polycrystalline samples were synthesized by conventional solid-state reaction. Magnetic characterizations of Sr{sub 1-x}Ca{sub x}Mn{sub 0.5}Ti{sub 0.5}O{sub 3} revealed signature of antiferromagnetic ordering at temperatures (T{sub N}) ∝ 19, 25 and 29.5 K for x = 0.25, x = 0.5 and for x = 0.75, respectively. Sr{sub 1-x}Ca{sub x}Mn{sub 0.5}Ti{sub 0.5}O{sub 3} (x = 0.75) exhibits field-induced antiferromagnetic to ferromagnetic transition at ∝ 30 K with applied magnetic field of 4 and 5 T. Magnetocaloric change (ΔS{sub M}) increases from 3.5 to 19 J/kg K by increasing calcium concentration in the A-site. Those ΔS{sub M} values are relatively very high in these classes of antiferromagnetic perovskite systems and equal to the magnetisation values of the ferromagnetic perovskite manganites. This is the first report for the Sr{sub 1-x}Ca{sub x}Mn{sub 0.5}Ti{sub 0.5}O{sub 3} (x = 0.75) having large magnetic entropy changes induced by the low magnetic field. (orig.)

Investigation on the parameter optimization and performance of laser cladding a gradient composite coating by a mixed powder of Co50 and Ni/WC on 20CrMnTi low carbon alloy steel

Science.gov (United States)

Shi, Yan; Li, Yunfeng; Liu, Jia; Yuan, Zhenyu

2018-02-01

In this study, a gradient composite coating was manufactured on 20CrMnTi alloy steel by laser cladding. The laser power, cladding scan velocity and powder flow rate were selected as influencing factors of the orthogonal cladding experiments. The influencing factors were optimized by the comprehensive analysis of Taguchi OA and TOPSIS method. The high significant parameters and the predicted results were confirmed by the ANOVA method. The macromorphology and microstructures are characterized by using laser microscope, SEM, XRD and microhardness tester. Comparison tests of wear resistance of gradient composite coating, 20CrMnTi cemented quenching sample and the 20CrMnTi sample were conducted on the friction-wear tester. The results show that the phases are γ-Co solid solution, Co3B, M23C6 and etc. The interlayers and wear-resisting layer also contain new hard phases as WC, W2C. The microhardness of the gradient coating was increased to 3 times as compared with that of the 20CrMnTi substrate. The wear resistance of the gradient composite coating and 20CrMnTi cemented quenching sample was enhanced to 36.4 and 15.9 times as compared with that of the 20CrMnTi.

Determination of photo-catalytic activity of un-doped and Mn-doped TiO2 anatase powders on acetaldehyde under UV and visible light

International Nuclear Information System (INIS)

Papadimitriou, Vassileios C.; Stefanopoulos, Vassileios G.; Romanias, Manolis N.; Papagiannakopoulos, Panos; Sambani, Kyriaki; Tudose, Valentin; Kiriakidis, George

2011-01-01

Titanium dioxide (TiO 2 ) photocatalytic powder materials doped with various levels of manganese (Mn) were synthesized to be used as additives to wall painting in combating indoor and outdoor air pollution. The heterogeneous photocatalytic degradation of gaseous acetaldehyde (CH 3 CHO) on Mn–TiO 2 surfaces under ultraviolet and visible (UV/Vis) irradiation was investigated, by employing the Photochemical Static Reactor coupled with Fourier-Transformed Infrared spectroscopy (PSR/FTIR) technique. Experiments were performed by exposing acetaldehyde (∼ 400 Pa) and synthetic air mixtures (∼ 1.01 × 10 5 Pa total pressure) on un-doped TiO 2 and doped with various levels of Mn (0.1–33% mole percentage) under UV and visible irradiation at room temperature. Photoactivation was initiated using either UV or visible light sources with known emission spectra. Initially, the photo-activity of CH 3 CHO under the above light sources, and the physical adsorption of CH 3 CHO on Mn–TiO 2 samples in the absence of light were determined prior to the photocatalytic experiments. The photocatalytic loss of CH 3 CHO on un-doped TiO 2 and Mn–TiO 2 samples in the absence and presence of UV or visible irradiation was measured over a long time period (≈ 60 min), to evaluate their relative photocatalytic activity. The gaseous photocatalytic end products were also determined using absorption FTIR spectroscopy. Carbon dioxide (CO 2 ) was identified as the main photocatalysis product. It was found that 0.1% Mn–TiO 2 samples resulted in the highest photocatalytic loss of CH 3 CHO under visible irradiation. This efficiency was drastically diminished at higher levels of Mn doping (1–33%). The CO 2 yields were the highest for 0.1% Mn–TiO 2 samples under UV irradiation, in agreement with the observed highest CH 3 CHO decomposition rates. It was demonstrated that low-level (0.1%) doping of TiO 2 with Mn results in a significant increase of their photocatalytic activity in the visible

Synthesis and electrochemical properties of LiNi0.4Mn1.5Cr0.1O4 and Li4Ti5O12

CSIR Research Space (South Africa)

Liu, GQ

2011-08-01

Full Text Available Spinel compound LiNi0.4Mn1.5Cr0.1O4 (LNMCO) and Li4Ti5O12 (LTO) were synthesized by the sol-gel method and the solid-state method, respectively. The particle sizes of the products LiNi0.4Mn1.5Cr0.1O4 and Li4Ti5O12 were 0.5 to 2 um and 0.5 to 0.8 um...

The poisoning effect of PbO on Mn-Ce/TiO{sub 2} catalyst for selective catalytic reduction of NO with NH{sub 3} at low temperature

Energy Technology Data Exchange (ETDEWEB)

Zhou, Lingling [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Li, Caiting, E-mail: ctli@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Zhao, Lingkui; Zeng, Guangming; Gao, Lei; Wang, Yan; Yu, Ming’e [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China)

2016-12-15

Highlights: • The poisoning effects of PbO-doped Mn-Ce/TiO{sub 2} catalysts for low temperature NH{sub 3}-SCR were investigated. • Low concentration of Mn{sup 4+} and chemisorbed oxygen (O{sub b}) were not favorable for the generation of intermediates. • The decreased Ce{sup 3+} and less reducible of manganese oxides hindered the redox cycle (Mn{sup 3+} + Ce{sup 4+} ↔ Mn{sup 4+} + Ce{sup 3+}). • The doping of PbO not only altered acid sites but also inhibited ammonia adsorption as well as activation. • The poisoning of PbO resulted in the decrease of ad-NO{sub x} species (only a spot of bidentate nitrates remained). - Abstract: Lead oxide (PbO) as one of the typical heavy metals in flue gas from power plants has strong accumulation as well as poisoning effects on SCR catalysts. In this paper, a series of PbO-doped Mn-Ce/TiO{sub 2} catalysts were synthesized by impregnation method. The poisoning effects of PbO over Mn-Ce/TiO{sub 2} samples for selective catalytic reduction of NO by NH{sub 3} were investigated based on catalytic activity test and characterizations. The NO conversion of Mn-Ce/TiO{sub 2} was greatly decreased after the addition of PbO. It was obvious that the NO conversion efficiency of Mn-Ce/TiO{sub 2} catalyst declined from 96.75% to about 40% at 200 °C when Pb:Mn molar ratio reached 0.5. Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Hydrogen temperature programmed reduction (H{sub 2}-TPR), Ammonia temperature programmed desorption (NH{sub 3}-TPD) and Fourier transform infrared spectroscopy (FT-IR) were carried out to study the deactivation reasons of PbO poisoned catalysts. Manganese oxides’ crystallization, less reducible of manganese and cerium oxides, the decreasing of surface area, Mn{sup 4+} as well as Ce{sup 3+} concentration and chemisorbed oxygen (O{sub b}) after the introduction of PbO, all of these resulted in a poor SCR performance

Microstructure and Wear Resistance of TiC Composite Coating in situ Synthesized on 35CrMnSi Steel by Argon Arc Cladding%35CrMnSi 表面氩弧熔覆原位自生 TiC 复合涂层的组织及耐磨性

Institute of Scientific and Technical Information of China (English)

丁天; 孟君晟; 乔盛楠; 吕东亮; 宋永平; 李阳

2014-01-01

Objective To improve the wear resistance of cutting tooth and to prolong its service life. Methods The TiC enhanced nickel-based composite coating was prepared on the surface of 35CrMnSi steel by argon arc cladding technique. The microstructure of the coating was analyzed by OM, SEM and XRD. Microhardness and wear resistance at room temperature of the composite coat-ing were examined by means of microhardness testing and impact abrasion resistance testing, respectively. Results The compact microstructure was obtained in the composite coating, and good metallurgical bonding could be obtained between the 35CrMnSi steel and cladding coating, with the main phases of TiC, γ-Ni and M23 C6 . The majority of TiC was blocky. The TiC particles was about 1 ~ 2 μm in size and the particles were dispersed in the coatings. The hardness and wear resistance of the coating were related with the (Ti+C) content. The highest hardness of 20% (Ti+C) coating was 1190HV. The relative wear resistance of the composite coating was 7. 5 times higher than that of 35CrMnSi steel. Conclusion The cladding coating reinforced by TiC particle showed ap-parently improved surface hardness as compared to 35CrMnSi steel. The wear mechanism of the composite coating under impact loading at room temperature was micro-cutting wear. The wear resistance of coating was greatly increased by argon arc cladding.%目的：提高截齿的耐磨性,延长其使用寿命。方法利用氩弧熔覆技术在35CrMnSi 钢表面制备 TiC 增强镍基复合涂层,分析涂层的显微组织和物相组成,测试涂层在室温下的显微硬度和耐磨性,并分析磨损机制。结果氩弧熔覆涂层的显微组织致密均匀,涂层与基体呈冶金结合,主要由 TiC,γ-Ni, M23 C6等物相组成。 TiC 颗粒呈块状,尺寸为1~2μm,弥散分布在涂层中。涂层硬度和耐磨性与(Ti+C)含量有关,熔覆粉末中(Ti+C)质量分数为20%时,涂层最高硬度可达1190HV,耐磨性达到基体的7.5�

Effects of homogenization on microstructures and properties of a new type Al-Mg-Mn-Zr-Ti-Er alloy

International Nuclear Information System (INIS)

He, L.Z.; Li, X.H.; Liu, X.T.; Wang, X.J.; Zhang, H.T.; Cui, J.Z.

2010-01-01

Research highlights: These new type alloys are very potential for increased use in aerospace and automobile industries. However, most of published reports have focused on the effects of Cu, Sc, Zr, Ag, rare metals and Si additions, Portevin-LeChatelier effect, corrosion properties, friction stir welding and superplasticity in 5000-series aluminum alloy, few investigated on Er and stepped homogenization on the precipitation of dispersoids in Al-Mg-Mn alloy. The purpose of this work was to study the effects of Er and homogenization treatment on mechanical properties and microstructural evolution in new type Al-Mg-Mn-Er alloy. - Abstract: Microstructural evolutions and mechanical properties of Al-Mg-Mn-Zr-Ti-Er alloy after homogenization were investigated in detail by optical microscope (OM), scanning electronic microscope (SEM), transmission electronic microscope (TEM), energy dispersive spectrum (EDS) and tensile test. A maximum tensile strength is obtained when the alloy homogenized at 510 deg. C for 16 h. With increasing preheating temperature (200-400 deg. C), the strength of the alloy finial homogenized at 490 deg. C for 16 h increases. When the preheating temperature is ≥300 deg. C, the strengths of the two-step homogenized alloys are higher than those of the single homogenized alloys. The preheating stage plays an important role in the microstructures and properties of the final homogenized alloy. Many fine (Mn,Fe)Al 6 precipitates when the preheating temperature is 400 deg. C. ErAl 3 phase cannot be observed during preheating stage. Plenty of fine (Mn,Fe)Al 6 and ErAl 3 precipitate in finial homogenized alloy when the preheating temperature is ≥300 deg. C. The Al-Mg-Mn-Zr-Ti-Er alloy is effectively strengthened by substructure and dispersoids of (Mn,Fe)Al 6 and ErAl 3 .

Utilizing Co2+/Co3+ Redox Couple in P2-Layered Na0.66Co0.22Mn0.44Ti0.34O2 Cathode for Sodium-Ion Batteries.

Science.gov (United States)

Wang, Qin-Chao; Hu, Enyuan; Pan, Yang; Xiao, Na; Hong, Fan; Fu, Zheng-Wen; Wu, Xiao-Jing; Bak, Seong-Min; Yang, Xiao-Qing; Zhou, Yong-Ning

2017-11-01

Developing sodium-ion batteries for large-scale energy storage applications is facing big challenges of the lack of high-performance cathode materials. Here, a series of new cathode materials Na 0.66 Co x Mn 0.66- x Ti 0.34 O 2 for sodium-ion batteries are designed and synthesized aiming to reduce transition metal-ion ordering, charge ordering, as well as Na + and vacancy ordering. An interesting structure change of Na 0.66 Co x Mn 0.66- x Ti 0.34 O 2 from orthorhombic to hexagonal is revealed when Co content increases from x = 0 to 0.33. In particular, Na 0.66 Co 0.22 Mn 0.44 Ti 0.34 O 2 with a P2-type layered structure delivers a reversible capacity of 120 mAh g -1 at 0.1 C. When the current density increases to 10 C, a reversible capacity of 63.2 mAh g -1 can still be obtained, indicating a promising rate capability. The low valence Co 2+ substitution results in the formation of average Mn 3.7+ valence state in Na 0.66 Co 0.22 Mn 0.44 Ti 0.34 O 2 , effectively suppressing the Mn 3+ -induced Jahn-Teller distortion, and in turn stabilizing the layered structure. X-ray absorption spectroscopy results suggest that the charge compensation of Na 0.66 Co 0.22 Mn 0.44 Ti 0.34 O 2 during charge/discharge is contributed by Co 2.2+ /Co 3+ and Mn 3.3+ /Mn 4+ redox couples. This is the first time that the highly reversible Co 2+ /Co 3+ redox couple is observed in P2-layered cathodes for sodium-ion batteries. This finding may open new approaches to design advanced intercalation-type cathode materials.

Grain Refinement of Al-Si-Fe-Cu-Zn-Mn Based Alloy by Al-Ti-B Alloy and Its Effect on Mechanical Properties.

Science.gov (United States)

Yoo, Hyo-Sang; Kim, Yong-Ho; Jung, Chang-Gi; Lee, Sang-Chan; Lee, Seong-Hee; Son, Hyeon-Taek

2018-03-01

We investigated the effects of Al-5.0wt%Ti-1.0wt%B addition on the microstructure and mechanical properties of the as-extruded Al-0.15wt%Si-0.2wt%Fe-0.3wt%Cu-0.15wt%Zn-0.9wt%Mn based alloys. The Aluminum alloy melt was held at 800 °C and then poured into a mould at 200 °C. Aluminum alloys were hot-extruded into a rod that was 12 mm in thickness with a reduction ratio of 38:1. AlTiB addition to Al-0.15Si-0.2Fe-0.3Cu-0.15Zn-0.9Mn based alloys resulted in the formation of Al3Ti and TiB2 intermetallic compounds and grain refinement. With increasing of addition AlTiB, ultimate tensile strength increased from 93.38 to 99.02 to 100.01 MPa. The tensile strength of the as-extruded alloys was improved due to the formation of intermetallic compounds and grain refinement.

Microstructure and mechanical properties of a novel near-α titanium alloy Ti6.0Al4.5Cr1.5Mn

International Nuclear Information System (INIS)

Wang, Hong-bin; Wang, Shu-sen; Gao, Peng-yue; Jiang, Tao; Lu, Xiong-gang; Li, Chong-he

2016-01-01

Based on previous Ti-Al-Cr-Mn quaternary system thermodynamic database, a novel near-α titanium alloy Ti-6.0Al-4.5Cr-1.5Mn alloy was designed and successfully prepared by the water-cooled copper crucible. Microscopic observation showed that both as-cast and annealing status consist of α phase, which coincides with the theoretical expectation. The mechanical properties at room temperature were measured and this alloy possesses good mechanical properties, its average yield-strength reaches 1051.5 MPa and tensile-strength is up to 1091.2 MPa while its average elongation is just 8.3%. Compared with the TA15, it has better mechanical strength and worse elongation. In the new alloy Laves phase Cr 2 Ti were detected by XRD pattern and TEM, which may cause the alloy's poor plasticity.

Microstructure and mechanical properties of a novel near-α titanium alloy Ti6.0Al4.5Cr1.5Mn

Energy Technology Data Exchange (ETDEWEB)

Wang, Hong-bin [State Key Laboratory of Advanced Special Steel & Shanghai Key Laboratory of Advanced Ferrometallurgy & School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); Shanghai Special Casting Engineering Technology Research Center, Shanghai 201605 (China); Wang, Shu-sen; Gao, Peng-yue; Jiang, Tao [State Key Laboratory of Advanced Special Steel & Shanghai Key Laboratory of Advanced Ferrometallurgy & School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); Lu, Xiong-gang; Li, Chong-he [State Key Laboratory of Advanced Special Steel & Shanghai Key Laboratory of Advanced Ferrometallurgy & School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); Shanghai Special Casting Engineering Technology Research Center, Shanghai 201605 (China)

2016-08-30

Based on previous Ti-Al-Cr-Mn quaternary system thermodynamic database, a novel near-α titanium alloy Ti-6.0Al-4.5Cr-1.5Mn alloy was designed and successfully prepared by the water-cooled copper crucible. Microscopic observation showed that both as-cast and annealing status consist of α phase, which coincides with the theoretical expectation. The mechanical properties at room temperature were measured and this alloy possesses good mechanical properties, its average yield-strength reaches 1051.5 MPa and tensile-strength is up to 1091.2 MPa while its average elongation is just 8.3%. Compared with the TA15, it has better mechanical strength and worse elongation. In the new alloy Laves phase Cr{sub 2}Ti were detected by XRD pattern and TEM, which may cause the alloy's poor plasticity.

Mn-Ce-V-WOx/TiO2 SCR Catalysts: Catalytic Activity, Stability and Interaction among Catalytic Oxides

Directory of Open Access Journals (Sweden)

Xuteng Zhao

2018-02-01

Full Text Available A series of Mn-Ce-V-WOx/TiO2 composite oxide catalysts with different molar ratios (active components/TiO2 = 0.1, 0.2, 0.3, 0.6 have been prepared by wet impregnation method and tested in selective catalytic reduction (SCR of NO by NH3 in a wide temperature range. These catalysts were also characterized by X-ray diffraction (XRD, Transmission Electron Microscope (TEM, in situ Fourier Transform infrared spectroscopy (in situ FTIR, H2-Temperature programmed reduction (H2-TPR and X-ray photoelectron spectroscopy (XPS. The results show the catalyst with a molar ratio of active components/TiO2 = 0.2 exhibits highest NO conversion value between 150 °C to 400 °C and good resistance to H2O and SO2 at 250 °C with a gas hourly space velocity (GHSV value of 40,000 h−1. Different oxides are well dispersed and interact with each other. NH3 and NO are strongly adsorbed on the catalyst surface and the adsorption of the reactant gas leads to a redox cycle with the valence state change among the surface oxides. The adsorption of SO2 on Mn4+ and Ce4+ results in good H2O and SO2 resistance of the catalyst, but the effect of Mn and Ce are more than superior water and sulfur resistance. The diversity of valence states of the four active components and their high oxidation-reduction performance are the main reasons for the high NO conversion in this system.

Influence of silver addition on the microstructure and mechanical properties of squeeze cast Mg-6Al-1Sn-0.3Mn-0.3Ti

International Nuclear Information System (INIS)

Acikgoez, Sehzat; Sevik, Hueseyin; Kurnaz, S.Can

2011-01-01

Graphical abstract: Highlights: → X-ray diffractometry reveals that the main phases are α-Mg, α-Ti, β-Mg 17 Al 12 and Al 8 Mn 5 in the base alloy. → With addition of silver, Al 81 Mn 19 phase was found. → The mechanical properties of the base alloy are improved with addition of silver. → The fracture surface of base alloy shows relatively deeper and more amount of dimples than that of alloys containing silver. - Abstract: In this study, the effect of silver (0, 0.2, 0.5, and 1 wt.%) on the microstructure and mechanical properties of a magnesium-based alloy (Mg-Al 6 wt.%-Sn 1 wt.%-Mn 0.3 wt.%-Ti 0.3 wt.%) were investigated. The alloys were produced under a controlled atmosphere by a squeeze-casting process. X-ray diffractometry revealed that the main phases are α-Mg, α-Ti, β-Mg 17 Al 12 and Al 8 Mn 5 in the all of alloys. In addition to, Al 81 Mn 19 phase was found with Ag additive. Besides, the amount of β-Mg 17 Al 12 phase was decreased with increasing the amount of Ag. The strength of the base alloy was increased by solid solution mechanism and decreasing the amount of β-Mg 17 Al 12 phase with addition of Ag. Furthermore, existence of Al 81 Mn 19 phase can be acted an important role in the increase on the mechanical properties of the alloys.

Magnetic and transport properties of Ni2MnGa-BaTiO3 metal-insulator particulate composite with percolation threshold

International Nuclear Information System (INIS)

Won, C.J.; Kambale, R.C.; Hur, N.

2011-01-01

Highlights: → The Ni 2 MnGa-BaTiO 3 type composites were first time prepared by solid state reaction. → Temperature dependent magnetic properties reveal two kinds of transitions in these composite. → The present materials show negative magnetoresistance effect. → The present studies on magnetic and electrical transport of metal/insulator (NMG/BTO) composites shows the resistivity change associated to filamentary conducting path at percolation threshold. - Abstract: Here we report the magnetic and transport properties of the metal/insulator (f NMG )Ni 2 MnGa/(1 - f NMG )BaTiO 3 composites. The X-ray diffraction study confirms the formation of both the phases in composite. The microstructure reveals that the conducting Ni 2 MnGa particles are well dispersed in an insulating BaTiO 3 matrix. Temperature dependent magnetization shows two transitions one above 300 K and other below 150 K. The temperature dependence resistivity near the percolation threshold f NMG = 0.4 had drastic changes which is higher than the f NMG = 0.5. Also the negative magnetoresistance effect was observed for the studied materials. We suggest that magnetic and transport properties at the percolation threshold can be adjusted by the strain from the surrounding insulator particle.

Trends in (LaMnO3)n/(SrTiO3)m superlattices with varying layer thicknesses

KAUST Repository

Jilili, J.; Cossu, Fabrizio; Schwingenschlö gl, Udo

2015-01-01

We investigate the thickness dependence of the structural, electronic, and magnetic properties of (LaMnO3)n/(SrTiO3)m (n, m = 2, 4, 6, 8) superlattices using density functional theory. The electronic structure turns out to be highly sensitive

Enhancement in electrical and magnetic properties with Ti-doping in Bi0.5La0.5Fe0.5Mn0.5O3

Science.gov (United States)

Singh, Rahul; Gupta, Prince Kumar; Kumar, Shiv; Joshi, Amish G.; Ghosh, A. K.; Patil, S.; Chatterjee, Sandip

2017-04-01

In this investigation, we have synthesized Bi0.5La0.5Fe0.5Mn0.5-xTixO3 (where x = 0 and 0.05) samples. The Rietveld refinement of X-ray diffraction (XRD) patterns shows that the systems crystallize in the orthorhombic phase with the Pnma space group. The observed Raman modes support the XRD results. The appearance of prominent A1-3 and weak E-2 modes in Bi0.5La0.5Fe0.5Mn0.45Ti0.05O3 indicates the presence of chemically more active Bi-O covalent bonds. Ferromagnetism of Bi0.5La0.5Fe0.5Mn0.5O3 is enhanced by Ti doping at the Mn-site, indicating that these particular samples might be interesting for device applications.

The role of medium range order on phase transitions in chain silicates upon compression

International Nuclear Information System (INIS)

Serghiou, G; Chopelas, A; Boehler, R

2004-01-01

Raman spectroscopic measurements of the tetrahedrally coordinated crystal MnSiO 3 (rhodonite) in an argon pressure medium show that it becomes amorphous above 33 GPa. This observation consolidates our findings and explanation for the global structural trends exhibited by the extended chain silicate family AA'BO 3 (AA': Mg, Ca, Mn, Fe; B: Si) upon compression. In particular, crystals of this family are made of two types of building blocks coined P and C. Those crystals comprised solely of P blocks transform to dense higher coordinated crystalline phases; those comprised of P and C blocks, such as MnSiO 3 rhodonite, become amorphous; whereas those comprised solely of C blocks show both crystalline and amorphous regions upon compression. The reason that this medium range order length scale (building block scale) classification is correlated with the type of transitions taking place upon compression is due to the instability of C blocks and C-P interfaces with respect to P blocks and P-P interfaces at high pressures

Appearance and disappearance of ferromagnetism in ultrathin LaMnO3 on SrTiO3 substrate: A viewpoint from first principles

Science.gov (United States)

An, Ming; Weng, Yakui; Zhang, Huimin; Zhang, Jun-Jie; Zhang, Yang; Dong, Shuai

2017-12-01

The intrinsic magnetic state (ferromagnetic or antiferromagnetic) of ultrathin LaMnO3 films on the most commonly used SrTiO3 substrate is a long-existing question under debate. Either strain effect or nonstoichiometry was argued to be responsible for the experimental ferromagnetism. In a recent experiment [X. R. Wang, C. J. Li, W. M. Lü, T. R. Paudel, D. P. Leusink, M. Hoek, N. Poccia, A. Vailionis, T. Venkatesan, J. M. D. Coey, E. Y. Tsymbal, Ariando, and H. Hilgenkamp, Science 349, 716 (2015), 10.1126/science.aaa5198], one more mechanism, namely, the self-doping due to polar discontinuity, was argued to be the driving force of ferromagnetism beyond the critical thickness. Here systematic first-principles calculations have been performed to check these mechanisms in ultrathin LaMnO3 films as well as superlattices. Starting from the very precise descriptions of both LaMnO3 and SrTiO3, it is found that the compressive strain is the dominant force for the appearance of ferromagnetism, while the open surface with oxygen vacancies leads to the suppression of ferromagnetism. Within LaMnO3 layers, the charge reconstructions involve many competitive factors and certainly go beyond the intuitive polar catastrophe model established for LaAlO3/SrTiO3 heterostructures. Our paper not only explains the long-term puzzle regarding the magnetism of ultrathin LaMnO3 films but also sheds light on how to overcome the notorious magnetic dead layer in ultrathin manganites.

Fabrication of Mg-X-O (X = Fe, Co, Ni, Cr, Mn, Ti, V, and Zn) barriers for magnetic tunnel junctions

Science.gov (United States)

Yakushiji, K.; Kitagawa, E.; Ochiai, T.; Kubota, H.; Shimomura, N.; Ito, J.; Yoda, H.; Yuasa, S.

2018-05-01

We fabricated magnetic tunnel junctions with a 3d-transition material(X)-doped MgO (Mg-X-O) barrier, and evaluated the effect of the doping on magnetoresistance (MR) and microstructure. Among the variations of X (X = Fe, Co, Ni, Cr, Mn, Ti, V, and Zn), X = Fe and Mn showed a high MR ratio of more than 100%, even at a low resistance-area product of 3 Ωμm2. The microstructure analysis revealed that (001) textured orientation formed for X = Fe and Mn despite substantial doping (about 10 at%). The elemental mappings indicated that Fe atoms in the Mg-Fe-O barrier were segregated at the interfaces, while Mn atoms were evenly involved in the Mg-Mn-O barrier. This suggests that MgO has high adaptability for Fe and Mn dopants in terms of high MR ratio.

Enhancement of localization phenomena driven by covalency in the SrBiMn{sub 1.75}Ti{sub 0.25}O{sub 6} manganite

Energy Technology Data Exchange (ETDEWEB)

Asensio de Lucas, E.; Alvarez-Serrano, I. [Depto. Quimica Inorganica I, Facultad Ciencias Quimicas, Universidad Complutense de Madrid, E-28040 Madrid (Spain); Cuello, G.J. [Institut Laue-Langevin, 6 rue Jules Horowitz, F-38042 Grenoble (France); Garcia-Hernandez, M. [Instituto de Ciencia de Materiales de Madrid, CSIC, E-28049 Cantoblanco, Madrid (Spain); Lopez, M.L., E-mail: marisal@quim.ucm.es [Depto. Quimica Inorganica I, Facultad Ciencias Quimicas, Universidad Complutense de Madrid, E-28040 Madrid (Spain); Pico, C.; Veiga, M.L. [Depto. Quimica Inorganica I, Facultad Ciencias Quimicas, Universidad Complutense de Madrid, E-28040 Madrid (Spain)

2012-05-05

Graphical abstract: Enhancement of localization phenomena driven by covalency in the BiSrMn{sub 1.75}Ti{sub 0.25}O{sub 6} manganite. The CO/OO phenomena and magnetic clusters (Mn{sub 4}) stabilization at temperatures up to 520 K in BiSrMn{sub 1.75}Ti{sub 0.25}O{sub 6} are connected to a structural transition. The observed enhancement of electronic localization is interpreted considering covalent effects of Ti{sup 4+} and Bi{sup 3+} cations as the main driving force. Highlights: Black-Right-Pointing-Pointer The structural, electronic and magnetic behaviour of the new SrBiMn{sub 1.75}Ti{sub 0.25}O{sub 6} manganite is reported. Black-Right-Pointing-Pointer A structural transition above 520 K takes place, coinciding with relevant changes in the transport properties. Black-Right-Pointing-Pointer The electronic behavior is interpreted in terms of a remarkably high orbital and charge ordering temperature and cluster models. Black-Right-Pointing-Pointer The observed features are explained considering a scenario in which bonds covalence is enhanced by the Bi{sup 3+} and Ti{sup 4+} cations. - Abstract: Manganites are materials that show remarkable phenomena related to charge orbital ordering (CO/OO) and it is extremely important to understand the fundamental nature of this behaviour. This paper reports on the structural, electronic and magnetic behaviour of the new SrBiMn{sub 1.75}Ti{sub 0.25}O{sub 6} manganite and the dependence of these properties with temperature. A detailed structural analysis has been carried out by electron, X-ray, neutron diffraction between 4 and 700 K. The electron diffraction patterns obtained at room temperature (RT) evidence that the average structure (a{approx}b{approx}{radical}(2)a{sub p} and c {approx} 2a{sub p}) presents a modulation that doubles the a and c lattice parameters. A very high charge ordering (CO) transition temperature of 510 K, similar to that found for the non-doped material, SrBiMn{sub 2}O{sub 6}, is observed. Above this

Effect of MnO2 doping and temperature treatment on optical energy band gap properties in Zn-Bi-Ti-O varistor ceramics

International Nuclear Information System (INIS)

Ghazali, M. S. M.; Abdullah, W. R. W.; Zakaria, A.; Kamari, H. M.; Rizwan, Z.

2016-01-01

In this study, the optical band-gap energy ( Eg ) was investigated with respect to MnO 2 and sintering temperatures on ZnO based varistor ceramics. Eg of the ceramic (99-x) mol% ZnO + 0.5 mol% Bi 2 O 3 + 0.5 mol% TiO 2 + × MnO 2 where × = 0, 0.2, 0.4, 0.6 and 0.8 mol%, were determined using UV-Vis spectrophotometer. The samples was prepared through solid-state route and sintered at the sintering temperature from 1110, 1140 and 1170 °C for 45 and 90 min in open air. At no doping of MnO 2 , the values of Eg are 2.991 ± 0.001, 2.989 ± 0.001 eV for 45 and 90 min sintering time; respectively. Eg was decreased to 2.192 ± 0.001 eV at 1140 °C at 45 min sintering time. Similar result of Eg was observed at longer heat treatment. Further addition of dopant causing the Eg decreases rapidly to 2.099 and 2.106 ± 0.001 eV at 45 and 90 min sintering time; respectively. XRD analysis indicates that there is hexagonal ZnO and secondary phases, Zn 2 MnO 4 , Bi 4 Ti 3 O 12 and Zn 2 Ti 3 O 8 . The relative density of the sintered ceramics decreased or remain constant with the increase of MnO 2 concentration for 45 min sintering time, however, further prolong sintering time; the relative density decreases form 90.25 to 88.35%. This indicates the pores are increasing with the increase of heat treatment. The variation of sintering temperatures to the optical band gap energy of based ZnO varistor doped with MnO 2 due to the formation of interface states. (paper)

Dielectric permittivity in weakly concentrated SrTiO.sub.3./sub.:Mn crystals and ceramics

Czech Academy of Sciences Publication Activity Database

Trepakov, Vladimír; Savinov, Maxim; Železný, Vladimír; Pokorný, Jan; Syrnikov, P.; Azzoni, C. B.; Galinetto, P.; Mozzati, M. C.; Badalyan, A.; Deyneka, Alexander; Jastrabík, Lubomír

2007-01-01

Roč. 93, č. 1 (2007), 012017/1-012017/6 ISSN 1742-6588 R&D Projects: GA AV ČR KAN301370701; GA AV ČR 1QS100100563; GA MŠk(CZ) 1M06002 Institutional research plan: CEZ:AV0Z10100521; CEZ:AV0Z10100522 Keywords : dielectric permittivity * SrTiO 3 :Mn * crystals and ceramics Subject RIV: BM - Solid Matter Physics ; Magnetism

X-ray photoelectron spectroscopic study of direct reforming catalysts Ln{sub 0.5}Sr{sub 0.5}Ti{sub 0.5}Mn{sub 0.5}O{sub 3±d} (Ln = La, Nd, and Sm) for high temperature-operating solid oxide fuel cell

Energy Technology Data Exchange (ETDEWEB)

Kim, Keunsoo [Department of Engine Research, Korea Institute of Machinery and Materials, 156 Gajeongbuk-Ro, Daejeon 305-343 (Korea, Republic of); Jeong, Jihoon [Department of Mechanical Engineering, The University of Texas at Austin, Austin, TX 78712 (United States); Azad, Abul K. [Faculty of Integrated Technologies, University Brunei Darussalam, Jalan Tunku Link, Gadong BE1410 (Brunei Darussalam); Jin, Sang Beom [Department of Advanced Materials Science and Engineering, Hanbat National University, 125, Dongseo-Daero, Yusung-Gu, Daejeon 305-719 (Korea, Republic of); Kim, Jung Hyun, E-mail: jhkim2011@hanbat.ac.kr [Department of Advanced Materials Science and Engineering, Hanbat National University, 125, Dongseo-Daero, Yusung-Gu, Daejeon 305-719 (Korea, Republic of)

2016-03-01

Graphical abstract: Measured Ti 2p peaks and deconvolution peaks of Nd{sub 0.5}Sr{sub 0.5}Ti{sub 0.5}Mn{sub 0.5}O{sub 3±d} under oxidizing condition (left) and NSTM under reducing condition (right). - Highlights: • Chemical states of Ln{sub 0.5}Sr{sub 0.5}Ti{sub 0.5}Mn{sub 0.5}O{sub 3±d} (Ln: La, Nd and Sm) were analyzed. • Charge compensation occurred with the reduction of Mn and Ti. • The Nd substitution effect allowed some Ti to convert into a metallic behavioral component. • NSTM and SSTM had a large amount of lattice oxygen; however, LSTM retained a large quantity of adsorbed oxygen. - Abstract: Chemical states of lanthanide doped perovskite for direct reforming anode catalysts, Ln{sub 0.5}Sr{sub 0.5}Ti{sub 0.5}Mn{sub 0.5}O{sub 3±d} (Ln = La, Nd, and Sm) have been studied by X-ray Photoelectron Spectroscopy (XPS) in order to determine the effects of various lanthanide substitution in complex perovskites for high temperature-operating solid oxide fuel cells (HT-SOFC). The charge state of lanthanide ions remained at 3+ and the binding energies of the lanthanide ions in Ln{sub 0.5}Sr{sub 0.5}Ti{sub 0.5}Mn{sub 0.5}O{sub 3±d} were located in a relatively lower range compared to those of conventional lanthanide oxides. Mn and Ti were regarded as charge compensation components in Ln{sub 0.5}Sr{sub 0.5}Ti{sub 0.5}Mn{sub 0.5}O{sub 3±d}; Mn was more influential than Ti. In the cases of substituting Nd and Sm into Ln{sub 0.5}Sr{sub 0.5}Ti{sub 0.5}Mn{sub 0.5}O{sub 3±d}, some portion of Ti showed metallic behavior; the specific Mn satellite peak indicating an electro-catalytic effect had occurred. Three types of oxygen species comprised of lattice oxygen, carbonate species, and adsorbed oxygen species were observed in Ln{sub 0.5}Sr{sub 0.5}Ti{sub 0.5}Mn{sub 0.5}O{sub 3±d} from the O 1s spectra; a high portion of lattice oxygen was observed in both Nd{sub 0.5}Sr{sub 0.5}Ti{sub 0.5}Mn{sub 0.5}O{sub 3±d} (NSTM) and Sm{sub 0.5}Sr{sub 0.5}Ti{sub 0.5}Mn{sub 0.5}O

Pd-MnO2 nanoparticles/TiO2 nanotube arrays (NTAs) photo-electrodes photo-catalytic properties and their ability of degrading Rhodamine B under visible light.

Science.gov (United States)

Thabit, Mohamed; Liu, Huiling; Zhang, Jian; Wang, Bing

2017-10-01

Pd-MnO 2 /TiO 2 nanotube arrays (NTAs) photo-electrodes were successfully fabricated via anodization and electro deposition subsequently; the obtained Pd-MnO 2 /TiO 2 NTAs photo electrodes were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD) and characterized accordingly. Moreover, the light harvesting and absorption properties were investigated via ultraviolet-visible diffuse reflectance spectrum (DRS); photo degradation efficiency was investigated via analyzing the photo catalytic degradation of Rhodamine B under visible illumination (xenon light). The performed analyses illustrated that Pd-MnO 2 codoped particles were successfully deposited onto the surface of the TiO 2 nanotube arrays; DRS results showed significant improvement in visible light absorption which was between 400 and 700nm. Finally, the photo catalytic degradation efficiency results of the designated organic pollutant (Rhodamine B) illustrated a superior photocatalytic (PC) efficiency of approximately 95% compared to the bare TiO 2 NTAs, which only exhibited a photo catalytic degradation efficiency of approximately 61%, thus it indicated the significant enhancement of the light absorption properties of fabricated photo electrodes and their yield of OH radicals. Copyright © 2017. Published by Elsevier B.V.

Effects of Nb doping level on the electronic transport, photoelectric effect and magnetoresistance across La0.5Ca0.5MnO3/Nb:SrTiO3 junctions

Science.gov (United States)

Wang, J. F.; Jiang, Y. C.; Chen, M. G.; Gao, J.

2013-12-01

Heterojunctions composed of La0.5Ca0.5MnO3 and Nb doped SrTiO3 were fabricated, and the effects of the Nb doping level on their electronic transport, photoelectric effect, and magnetoresistance were investigated. A lower doping concentration of Nb led to better rectifying properties and higher open circuit voltages. The I-V curves for La0.5Ca0.5MnO3/0.7 wt. % Nb-SrTiO3 showed a negligible response to magnetic fields for all temperatures, whereas La0.5Ca0.5MnO3/0.05 wt. % Nb-SrTiO3 exhibited distinct magnetoresistance, which depended on both the bias voltage and temperature. These results are discussed with the assistance of conventional semiconductor theories.

Manipulating the magnetism and resistance state of Mn:ZnO/Pb(Zr0.52Ti0.48)O3 heterostructured films through electric fields

Science.gov (United States)

Li, Yong-Chao; Wu, Jun; Pan, Hai-Yang; Wang, Jue; Wang, Guang-Hou; Liu, Jun-Ming; Wan, Jian-Guo

2018-05-01

Mn:ZnO/Pb(Zr0.52Ti0.48)O3 (PZT) heterostructured films have been prepared on Pt/Ti/SiO2/Si wafers by a sol-gel process. Nonvolatile and reversible manipulation of the magnetism and resistance by electric fields has been realized. Compared with the saturation magnetic moment (Ms) in the +3.0 V case, the modulation gain of Ms can reach 270% in the -3.0 V case at room temperature. The resistance change is attributed to the interfacial potential barrier height variation and the formation of an accumulation (or depletion) layer at the Mn:ZnO/PZT interface, which can be regulated by the ferroelectric polarization direction. The magnetism of Mn:ZnO originates from bound magnetic polarons. The mobile carrier variation in Mn:ZnO, owing to interfacial polarization coupling and the ferroelectric field effect, enables the electric manipulation of the magnetism in the Mn:ZnO/PZT heterostructured films. This work presents an effective method for modulating the magnetism of magnetic semiconductors and provides a promising avenue for multifunctional devices with both electric and magnetic functionalities.

High-pressure synthesis and magnetic behavior of A-site columnar-ordered double perovskites, LnMn(Ga{sub 0.5}Ti{sub 0.5}){sub 2}O{sub 6} (Ln = Sm, Gd)

Energy Technology Data Exchange (ETDEWEB)

Shimura, Gen; Niwa, Ken; Shirako, Yuichi; Hasegawa, Masashi [Department of Crystalline Materials Science, Nagoya University, 464-8601, Nagoya (Japan)

2017-01-26

A-site columnar-ordered double perovskites, LnMn(Ga{sub 0.5}Ti{sub 0.5}){sub 2}O{sub 6} (Ln = Sm, Gd), were successfully synthesized under high pressure and high temperature (6 GPa, 1375 K). From the synchrotron powder X-ray diffraction patterns, all of the diffraction peaks can be indexed by the P4{sub 2}/nmc space group with lattice parameters a, c ∼ 2a{sub p} (a{sub p}: primitive cubic perovskite lattice) and no ordering of the B-site cations. Rietveld analysis of the synchrotron powder X-ray diffraction patterns and Curie-Weiss fitting of their magnetizations reveal that the ionic formulae of these perovskites are Ln{sup 3+}Mn{sup 2+}(Ga{sup 3+}{sub 0.5}Ti{sup 4+}{sub 0.5}){sub 2}O{sup 2-}{sub 6}. SmMn(Ga{sub 0.5}Ti{sub 0.5}){sub 2}O{sub 6} shows canted-antiferromagnetic behavior, whereas GdMn(Ga{sub 0.5}Ti{sub 0.5}){sub 2}O{sub 6} exhibits two different magnetic states at low temperature depending on the applied magnetic field and shows an unusual magnetization curve. These magnetic behaviors originate by decreasing the antiferromagnetic interaction by substituting Ga{sup 3+}(d{sup 10}) for Ti{sup 4+}(d{sup 0}) and by decreasing the ferromagnetic interaction between columnar-ordered Ln{sup 3+} and Mn{sup 2+}. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Influence of Cu alloying on hot ductility of C-Mn-Al and Ti-Nb microalloyed steels

Directory of Open Access Journals (Sweden)

Comineli, O.

2005-12-01

Full Text Available A beneficial effect of the copper on the hot ductility was observed in Ti-Nb microalloyed steels over the temperature range 800-1,000 °C at the cooling rate of 0.4 °C/s, but no influence at the cooling rate of 4 °C/s. Precipitates containing Nb and Ti were present whose size was coarser in the Cu-bearing grade as cooled at 0.4 °C/s. Cu-bearing precipitates were not found. In the C-Mn-Al steel, no influence of the copper on the hot ductility was recorded, but CuS particles were detected. Two mechanisms are proposed to explain the positive influence of the copper in the microalloyed steel. The first is that the copper atoms in the solid solution affect the activity of the carbon and the nitrogen analogically to the previously observed effect of the silicon, enhancing the precipitation at high temperatures, and another mechanism that the copper atoms can prolong the lifetime of vacancies generated by straining assisting the formation of TiNb-vacancy complexes and thereby coarsening the precipitates.

Se ha observado un efecto beneficioso del cobre sobre la ductilidad en caliente del acero microaleado al Ti-Nb, en el rango de temperaturas 800-1.000 °C. La influencia fue observada a velocidades de enfriamiento bajas, 0,4 °C/s, mientras que a 4 °C/s no se aprecia. En el acero C-Mn-Al, la influencia de cobre no fue detectada. En el acero microaleado se detectó la presencia de precipidados que contienen niobio y titanio, la dimensión de los cuales es mayor cuando se enfría a 0,4 °C/s. En este acero no se detectó la presencia de precipitados con contenidos de cobre, en contraste con el acero C-Mn-Al, donde sí se observaron partículas de CuS. Se proponen dos mecanismos para explicar la influencia positiva del cobre en aceros microaleados. El primero es el aumento de la actividad de carbono y nitrógeno en austenita debido a presencia de átomos de cobre en solución sólida, con el mismo efecto que el silicio, el cual aumenta la

2D Electron Gas with 100% Spin-Polarization in the (LaMnO3)2/(SrTiO3)2 Superlattice under Uniaxial Strain

KAUST Repository

Cossu, Fabrizio

2014-07-28

By first-principles calculations we investigate the structural, electronic, and magnetic properties of the (LaMnO3)2/(SrTiO3)2 superlattice. We find that a monoclinic C2h symmetry is energetically favorable and that the spins order ferromagnetically. Under both compressive and tensile uniaxial strain the electronic structure of the superlattice shows a half-metallic character. In particular, a fully spin-polarized two-dimensional electron gas, which traces back to the Ti 3dxy orbitals, is achieved under compressive uniaxial strain. The (LaMnO3)2/(SrTiO3)2 superlattice is analysed with respect to its structure, magnetism, and electronic properties. Our results demonstrate that uniaxial strain in an experimentally accessible range, both tensile and compressive, can be used to induce half-metallicity. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Structural, dielectric and magnetic properties of Mn modified xBiFeO{sub 3}-(1−x)BaTiO{sub 3} ceramics

Energy Technology Data Exchange (ETDEWEB)

Dai, Zhonghua, E-mail: zhdai@mail.xjtu.edu.cn [College of Mechanics and Materials, Hohai University, Nanjing 210098 (China); Ferroic Physics Group, National Institute for Materials Science, Tsukuba 305-0047, Ibaraki (Japan); Liu, Lu; Ying, Guobing; Yuan, Ming [College of Mechanics and Materials, Hohai University, Nanjing 210098 (China); Ren, Xiaobing [Ferroic Physics Group, National Institute for Materials Science, Tsukuba 305-0047, Ibaraki (Japan)

2017-07-15

Manganese doped xBiFeO{sub 3}-(1−x)BaTiO{sub 3}(x=0.67–0.82) ceramics were prepared by solid-state method. The structural, dielectric and magnetic properties were investigated after annealing in vacuum at 773 K. X-ray diffraction analysis indicated that all samples crystallized in pure perovskite structure. The ceramics displays a typical ferroelectric loop, with a max remnant polarization P{sub r} of 25.6 µC/cm{sup 2}. The piezoelectric coefficient d{sub 33} of Manganese doped 0.67BiFeO{sub 3}0.33BaTiO{sub 3} is 139 pC/N and its temperature dependence of dielectric constant exhibits a broad anomaly. The Manganese doped 0.75BiFeO{sub 3}0.25BaTiO{sub 3} ceramic shows ferrimagnetism at room temperature, with remnant magnetization M{sub r} of 0.31 emu/g and ferrimagnetic transition temperature T{sub N} of ~420 °C. - Highlights: • In this manuscript, a technique combined Mn doping which is able to fabricate point defects and annealing in vacuum which can stabilize the unstable ion was investigated. We studied the electrical properties of Mn doped BiFeO{sub 3}-BaTiO{sub 3} ceramics after vacuum annealing treatment at appropriate temperature. • Our result is that Mn modification and heat treatment are effective methods to solve the problem of high leakage of BiFeO{sub 3}-BaTiO{sub 3} system ceramic prepared by solid-state method. It exhibited a enhanced field-induced ferromagnetic ordering with promising potential in spintronics and recording media applications.

Piezoelectric properties and temperature stability of Mn-doped Pb(Mg1/3Nb2/3)-PbZrO3-PbTiO3 textured ceramics

OpenAIRE

Yan, Yongke; Cho, Kyung-Hoon; Priya, Shashank

2012-01-01

In this letter, we report the electromechanical properties of textured 0.4Pb(Mg1/3Nb2/3) O-3-0.25PbZrO(3)-0.35PbTiO(3) (PMN-PZT) composition which has relatively high rhombohedral to tetragonal (R-T) transition temperature (TR-T of 160 degrees C) and Curie temperature (T-C of 234 degrees C) and explore the effect of Mn-doping on this composition. It was found that MnO2-doped textured PMN-PZT ceramics with 5 vol.% BaTiO3 template (T-5BT) exhibited inferior temperature stability. The coupling f...

Preparation and characterization of La/sub 2/TiMnO/sub 6/

Energy Technology Data Exchange (ETDEWEB)

Ramanujachary, K V; Swamy, C S [Indian Inst. of Tech., Madras. Dept. of Chemistry

1981-01-01

The compound La/sub 2/TiMnO/sub 6/ has been prepared by solid state reaction of the component ions in suitable form. X-ray analysis shows it to be orthorhombic and the cell constants are a = 5.506 A, b = 5.950 A and c = 7.636 A. It is found to be essentially a p-type semiconductor with ..cap alpha.. = 150 ..mu..VKsup(-1). Weiss constant has a value -88K and it shows IR bands at 400-450 and 575-600 cmsup(-1) characteristic of ..nu../sub 3/ and ..nu../sub 4/ modes of the Tisup(4+) O/sub 6/ octahedra.

Structures and magnetic behaviours of TiO2–Mn–TiO2 multilayers

International Nuclear Information System (INIS)

Fa-Min, Liu; Peng, Ding; Jian-Qi, Li

2010-01-01

The TiO 2 -Mn-TiO 2 multilayers are successfully grown on glass and silicon substrates by alternately using radio frequency reactive magnetron sputtering and direct current magnetron sputtering. The structures and the magnetic behaviours of these films are characterised with x-ray diffraction, transmission electron microscope (TEM), vibrating sample magnetometer, and superconducting quantum interference device (SQUID). It is shown that the multi-film consists of a mixture of anatase and rutile TiO 2 with an embedded Mn nano-film. It is found that there are two turning points from ferromagnetic phase to antiferromagnetic phase. One is at 42 K attributed to interface coupling between ferromagnetic Mn 3 O 4 and antiferromagnetic Mn 2 O 3 , and the other is at 97 K owing to the interface coupling between ferromagnetic Mn and antiferromagnetic MnO. The samples are shown to have ferromagnetic behaviours at room temperature from hysteresis in the M-H loops, and their ferromagnetism is found to vary with the thickness of Mn nano-film. Moreover, the Mn nano-film has a critical thickness of about 18.5 nm, which makes the coercivity of the multi-film reach a maximum of about 3.965×10 −2 T. (cross-disciplinary physics and related areas of science and technology)

Improving the fast discharge performance of high-voltage LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} spinel by Cu{sup 2+}, Al{sup 3+}, Ti{sup 4+} tri-doping

Energy Technology Data Exchange (ETDEWEB)

Deng, Jicheng [Electronic Materials Research Laboratory, Key Laboratory of the Ministry of Education & International Center for Dielectric Research, Xi' an Jiaotong University, Xi' an (China); Shaanxi Engineering Research Center of Advanced Energy Materials & Devices, Xi' an Jiaotong University, Xi' an (China); Xu, Youlong, E-mail: ylxuxjtu@mail.xjtu.edu.cn [Electronic Materials Research Laboratory, Key Laboratory of the Ministry of Education & International Center for Dielectric Research, Xi' an Jiaotong University, Xi' an (China); Shaanxi Engineering Research Center of Advanced Energy Materials & Devices, Xi' an Jiaotong University, Xi' an (China); Xiong, Lilong; Li, Liang [Electronic Materials Research Laboratory, Key Laboratory of the Ministry of Education & International Center for Dielectric Research, Xi' an Jiaotong University, Xi' an (China); Sun, Xiaofei [Shaanxi Engineering Research Center of Advanced Energy Materials & Devices, Xi' an Jiaotong University, Xi' an (China); Zhang, Yuan [Electronic Materials Research Laboratory, Key Laboratory of the Ministry of Education & International Center for Dielectric Research, Xi' an Jiaotong University, Xi' an (China)

2016-08-25

The sluggish Li{sup +} ion diffusion coefficient at ∼4.7 V (vs. Li{sup +}/Li) greatly impairs the fast discharge performance of LiMn{sub 1.5}Ni{sub 0.5}O{sub 4} cathode material. Herein, a tri-doping strategy is proposed where Cu{sup 2+}, Al{sup 3+}, Ti{sup 4+} ions are partially substituted for Ni{sup 2+} and Mn{sup 4+}. Cu{sup 2+}, Al{sup 3+}, Ti{sup 4+} tri-doping effectively suppresses the Li{sub x}Ni{sub 1−x}O impurity phase, increases the cation mixing in the octahedral B-site in the spinel, enlarges the electronic conductivity, and enhances the structural stability. Most importantly, the Li{sup +} diffusion coefficients show a peculiar boost at 4.7 V by two orders of magnitude after tri-doping. Compared to the pristine LiMn{sub 1.5}Ni{sub 0.5}O{sub 4} (denoted P-LNM), the tri-doped Li[Ni{sub 0.455}Cu{sub 0.03}Al{sub 0.03}Mn{sub 1.455}Ti{sub 0.03}]O{sub 4} (denoted TD-LNM) exhibits much better fast discharge performance, delivering a specific capacity of ∼101 mAh g{sup −1} at 100 C discharge rate. - Graphical abstract: For the LiMn{sub 1.5}Ni{sub 0.5}O{sub 4} cathode material, the sluggish Li{sup +} ion diffusion coefficient around the ∼4.7 V (vs. Li{sup +}/Li) plateau greatly impair its fast discharge performance, which therefore limit its application in electric vehicles. Herein, a tri-doping strategy is proposed where Cu{sup 2+}, Al{sup 3+}, Ti{sup 4+} ions are partially substituted for Ni{sup 2+} and Mn{sup 4+}. After tri-doping, the Li{sup +} diffusion coefficient at 4.7 V (vs. Li{sup +}/Li) is boosted by two orders of magnitude. Compared to the pristine LiMn{sub 1.5}Ni{sub 0.5}O{sub 4} (denoted P-LNM), the tri-doped Li[Ni{sub 0.455}Cu{sub 0.03}Al{sub 0.03}Mn{sub 1.455}Ti{sub 0.03}]O{sub 4} (denoted TD-LNM) exhibits much better fast discharge performance, delivering a capacity of ∼101 mAh·g{sup −1} at 100 C discharge rate. - Highlights: • Cu, Al, Ti Tri-doping improves electronic conductivity of LiNi{sub 0.5}Mn{sub 1.5}O{sub 4}. • Cu

Synthesis, structural characteristics and dielectric properties of a new K{sub 2}NiF{sub 4}-type phase Sr{sub 2}Mn{sub 0.5}Ti{sub 0.5}O{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Chupakhina, T.I., E-mail: chupakhina@ihim.uran.ru [Institute of Solid State Chemistry of the Ural Branch of the Russian Academy of Sciences, 91, Pervomaiskaya Str., Ekaterinburg (Russian Federation); Melnikova, N.V. [Ural Federal University, 19, Mira Str., Ekaterinburg (Russian Federation); Gyrdasova, O.I. [Institute of Solid State Chemistry of the Ural Branch of the Russian Academy of Sciences, 91, Pervomaiskaya Str., Ekaterinburg (Russian Federation)

2016-06-15

A new K{sub 2}NiF{sub 4}-type phase Sr{sub 2}Mn{sub 0,5}Ti{sub 0,5}O{sub 4} have been synthesized by a sol–gel procedure and characterized by X-ray powder diffraction, thermogravimetric analysis and scanning electron microscopy. There are no oxide ion vacancies in these materials; oxidation states of manganese and titanium were estimated as +4. Rietveld profile analysis shows that the phase crystallizes with tetragonal unit cell in the space group I4/mmm. Substitution of Ti{sup 4+} for Mn{sup 4+} does not affect the distortion of coordination polyhedra (Mn,Ti)O{sub 6} and SrO{sub 9}. The dielectric properties of the ceramic samples are caused by structural and charge characteristics, regular coordination polyhedra SrO{sub 9} and lack of charge ordering, which can lead to significant permittivity. Increase of the dielectric constant at temperatures above 453 K is caused mainly by the grain boundary processes explained in terms of the Maxwell–Wagner polarization model. - Highlights: • The new complex oxide Sr{sub 2}Mn{sub 0,5}Ti{sub 0,5}O{sub 4} was prepared. • The structures of the compound were analyzed by Rietveld refinement. • Distortions of SrO{sub 9} and (Mn,Ti)O{sub 6} polyhedra are not strong. • Dielectric properties are determined by regular structure and lack of charge ordering. • Permittivity increase under heat is associated with processes at the grain boundaries.

Effects of Al-Mn-Ti-P-Cu master alloy on microstructure and properties of Al-25Si alloy

Directory of Open Access Journals (Sweden)

Xu Chunxiang

2013-09-01

Full Text Available To obtain a higher microstructural refining efficiency, and improve the properties and processing ability of hypereutectic Al-25Si alloy, a new environmentally friendly Al-20.6Mn-12Ti-0.9P-6.1Cu (by wt.% master alloy was fabricated; and its modification and strengthening mechanisms on the Al-25Si alloy were studied. The mechanical properties of the unmodified, modified and heat treated alloys were investigated. Results show that the optimal addition amount of the Al-20.6Mn-12Ti-0.9P-6.1Cu master alloy is 4wt.%. In this case, primary Si and eutectic Si as well as メ-Al phase were clearly refined, and this refining effect shows an excellent long residual action as it can be heat-retained for at least 5 h. After being T6 heat treated, the morphology of primary and eutectic Si in the Al-25Si alloys with the addition of 4wt.% Al-20.6Mn-12Ti-0.9P-6.1Cu alloy changes into particles and short rods. The average grain size of the primary and eutectic Si decreases from 250 レm (unmodified to 13.83 レm and 35 レm (unmodified to 7 レm; the メ-Al becomes obviously finer and the distribution of Si phases tends to be uniform and dispersed. Meanwhile, the tensile properties are improved obviously; the tensile strengths at room temperature and 300 ìC reach 241 MPa and 127 MPa, increased by 153.7% and 67.1%, respectively. In addition, the tensile fracture mechanism changes from brittle fracture for the alloy without modification to ductile fracture after modification. Modifying the morphology of Si phase and strengthening the matrix can effectively block the initiation and propagation of cracks, thus improving the strength of the hypereutectic Al-25Si alloy.

Training effect of exchange bias in La0.67Sr0.33MnO3/SrTiO3 superlattice

International Nuclear Information System (INIS)

Zhu, S J; Zhao, B R; Xu, B; Zhu, B Y; Cao, L X; Qiu, X G

2008-01-01

The training effect of exchange bias has been observed in the superlattice consisting of ferromagnetic La 0.67 Sr 0.33 MnO 3 and non-magnetic SrTiO 3 layers. The exchange field shows an approximately power-law decrease with an increase in the number of hysteresis loop measurements. The vertical shift of the hysteresis loop reveals the existence of the net uncompensated spins at the interface between the La 0.67 Sr 0.33 MnO 3 and the SrTiO 3 layers. The irreversibility of magnetization measurements gives clear evidence that the interfacial spins will be frozen at low temperature. It is suggested that the frozen uncompensated spins at the interface are responsible for the shift of the hysteresis loop and the training effect of exchange bias might be a result of the relaxation process of those interfacial spins when the superlattice is consecutively field-cycled.

The effect of heat treatment variables on the phase transformations at 1,420 C in Ti-48Al and Ti-48Al-2Mn-2Nb alloys

International Nuclear Information System (INIS)

Ramanujan, R.V.

1995-01-01

The effect of heat treatment variables such as initial microstructure, isothermal reaction time and cooling rate on the phase transformations occurring at 1,420 C in Ti-48Al and Ti-48Al-2Mn-2Nb alloys was studied. The main effect of the initial microstructure, which comprised either lamellae of α 2 and γ or equiaxed γ grains, was to alter the kinetics, through a change in the chemical driving force of the phase transformations. Therefore, the equiaxed γ grains transformed to α much faster than the lamellar structure and in the initially lamellar structure, growth of α resulted in the delineation of the initial dendritic structure formed during solidification. The effect of the rate of cooling from the heat treatment temperature on the final morphology of these alloys was drastic and resulted in a change in morphology from lamellar grains obtained on furnace cooling to a feathery and mottled morphology obtained on water quenching. TEM analysis of water quenched Ti-48Al-2Mn-2Nb revealed complex morphologies including a structure which consisted of equiaxed γ grains and residual α 2 and abutting colonies of γ and α 2 . Based on the TEM results, the early stages of formation of γ from α were studied and mechanisms of nucleation and growth discussed. The relative importance and the coexistence of massive and martensitic transformation products is also discussed

STUDY OF THE INSERTION AND EXTRACTION MECHANISM OF Li3Mn0.5Ti0.25O3

Directory of Open Access Journals (Sweden)

JINHE JIANG

2017-12-01

Full Text Available The metal oxide [Li3Mn0.5Ti0.25O3] was synthesized by solid state reaction crystallization method in certain temperature. It was an inverse spinel type compound metal oxide. The extraction/insertion reaction of this material was studied by X-ray, saturation exchange capacity value and distribution coefficient (Kd measurement value. In terms of its composition and chemical metrology, this inverse spinel material is very comprehensive; it is worth noting that it can be inserted or extracted by other substitutional ions and changes in lithium and oxygen stoichiometry while maintaining their crystal structure. The metal oxide [Li3Mn0.5Ti0.25O3] is inorganic Li+ exchanger which has an ion-memory capacity. It has high exchange selectivity ability for Li+. This metal oxide can be used to separate or extract Li+ in aqueous solution. The experimental result has confirmed inverse spinel type compound metal oxide which was treated by acid could attain 9.7 mmol‧g-1 Li+ exchanged capacity.

Shape memory and pseudoelastic properties of Fe-Mn-Si and Ti-Ni based alloys

International Nuclear Information System (INIS)

Guenin, G.

1997-01-01

The aim of this presentation is to analyse and discuss some recent advances in shape memory and pseudoelastic properties of different alloys. Experimental work in connection with theoretical ones will be reviewed. The first part is devoted to the microstructural origin of shape memory properties of Fe-Mn-Si based alloys (γ-ε transformation); the second part is a synthetic analysis of the effects of thermomechanical treatments on shape memory and pseudoelastic effects in Ti-Ni alloys, with some focus on the behaviour of the R phase introduced. (orig.)

A facile one-step synthesis of Mn{sub 3}O{sub 4} nanoparticles-decorated TiO{sub 2} nanotube arrays as high performance electrode for supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jianfang [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Wang, Yan [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Key Laboratory of Advance Functional Materials and Devices of Anhui Province, Hefei 230009 (China); Qin, Yongqiang, E-mail: albon@hfut.edu.cn [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Key Laboratory of Advance Functional Materials and Devices of Anhui Province, Hefei 230009 (China); Yu, Cuiping [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Cui, Lihua [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); School of Materials Science and Engineering, Beifang University of Nationalities, Yinchuan 750021 (China); Shu, Xia [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Cui, Jiewu; Zheng, Hongmei; Zhang, Yong [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Key Laboratory of Advance Functional Materials and Devices of Anhui Province, Hefei 230009 (China); Wu, Yucheng, E-mail: ycwu@hfut.edu.cn [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Key Laboratory of Advance Functional Materials and Devices of Anhui Province, Hefei 230009 (China)

2017-02-15

Via a facile one-step chemical bath deposition route, homogeneously dispersed Mn{sub 3}O{sub 4} nanoparticles have been successfully deposited onto the inner surface of TiO{sub 2} nanotube arrays (TNAs). The content and size of Mn{sub 3}O{sub 4} can be controlled by changing the deposition time. Field emission scanning electron microscopy and transmission electron microscopy analysis reveal the morphologies structures of Mn{sub 3}O{sub 4}/TNAs composites. The crystal-line structures are characterized by the X-ray diffraction patterns and Raman spectra. X-ray photoelectron spectroscopy further confirms the valence states of the sample elements. The electrochemical properties of Mn{sub 3}O{sub 4}/TNAs electrodes are systematically investigated by the combine use of cyclic voltammetry, galvanostatic charge-discharge and electrochemical impedance spectroscopy. The resulting Mn{sub 3}O{sub 4}/TNAs electrode prepared by deposition time of 3 h shows the highest specific capacitance of 570 F g{sup −1} at a current density of 1 A g{sup −1}. And it also shows an excellent long-term cycling stability at a current density of 5 A g{sup −1}, which remaining 91.8% of the initial capacitance after 2000 cycles. Thus this kind of Mn{sub 3}O{sub 4} nanoparticles decorated TNAs may be considered as an alternative promising candidate for high performance supercapacitor electrodes. - Graphical abstract: Mn{sub 3}O{sub 4} nanoparticles have been uniformly deposited onto the inner surfaces of TiO{sub 2} nanotube arrays through a facile one-step chemical bath deposition method. As electrodes for supercapacitors, they exhibit a relatively high specific capacity and excellent cycling stability. - Highlights: • Mn{sub 3}O{sub 4} nanoparticles have been deposited onto TiO{sub 2} nanotube arrays by chemical bath deposition. • The Mn{sub 3}O{sub 4}/TNAs exhibits a highest specific capacitance of 570 F g{sup –1} at a current density of 1 A g{sup –1}. • The Mn{sub 3}O{sub 4}/TNAs

The effect of secondary abnormal grain growth on the dielectric properties of La/Mn co-doped BaTiO3 ceramics

Directory of Open Access Journals (Sweden)

Živković Lj.M.

2006-01-01

Full Text Available La/Mn-codoped BaTiO3 systems, obtained by solid state reactions, were investigated regarding their microstructure characteristics and ferroelectric properties. Different concentrations of La2O3 were used for doping, ranging from 0.1 to 5.0 at% La, while a content of Mn was constant at 0.05 at%. For all samples sintered below the eutectic temperature (1332°C, a uniform microstructure was formed with average grain size from 1-3 μm. The appearance of secondary abnormal grains with (111 double twins grains with curved or faceted grain boundaries were observed in La/Mn BaTiO3 ceramics after sintering at temperatures above the eutectic temperature. All sintered samples exhibited a high electrical resistivity. Better dielectric performances were obtained for low doped samples (0.1 at% La sintered at 1350°C. For samples with La content above 1.0 at% a lower value in dielectric permittivity at higher sintering temperature is due to secondary abnormal grain growth, and to the presence of a non-ferroelectric phase rich in La. The Curie constant together with other dielectric parameters were also calculated.

Thermal conductivity in Pr{sub 1-x}Ca{sub x}MnO{sub 3} and SrTiO{sub 3} thin film systems

Energy Technology Data Exchange (ETDEWEB)

Wiedigen, Stefanie; Kramer, Thilo; Mangipudi, Kodanda R.; Hoffmann, Joerg; Volkert, Cynthia A.; Jooss, Christian [Institute for Materials Physics, University of Goettingen (Germany); Feuchter, Manuel; Kamlah, Marc [Institute for Applied Materials, Karlsruhe Institute of Technology (Germany)

2012-07-01

Epitaxial multilayers and superlattices are one recent approach for the design of efficient thermoelectrics. To study the effect of phonon blocking and scattering on thermal conductivity of oxide multilayers, a combination of two perovskites with promising thermoelectric properties is selected: the orthorhombic Pr{sub 1-x}Ca{sub x}MnO{sub 3} and the cubic SrTiO{sub 3}. In order to investigate the effect of microstructure, interfaces and acoustic impedance mismatch on thermal conductivity {kappa} high preparation quality is needed. Our thin films were prepared by ion-beam and magnetron sputtering. Structural analysis is done by XRD and TEM and is presented in combination with thermal conductivity measurements using the 3{omega} method. Single layers of Pr{sub 1-x}Ca{sub x}MnO{sub 3} show low {kappa} values and no significant increase of thermal conductivity with increasing doping. In homoepitaxial single layers of SrTiO{sub 3} preparation conditions have a high impact on {kappa}, most probably due to different concentrations of point defects. Pr{sub 1-x}Ca{sub x}MnO{sub 3}/SrTiO{sub 3} multilayers show a {kappa} decreases systematically with increasing number of double layers. The results are discussed in the light of the theoretically calculated phonon dispersion and the experimentally observed microstructure.

Evolution of electrical properties and domain configuration of Mn modified Pb(In1/2Nb1/2)O3-PbTiO3 single crystals

Science.gov (United States)

Qiao, Huimin; He, Chao; Yuan, Feifei; Wang, Zujian; Li, Xiuzhi; Liu, Ying; Guo, Haiyan; Long, Xifa

2018-04-01

The acceptor doped relaxor-based ferroelectric materials are useful for high power applications such as probes in ultrasound-guided high intensity focused ultrasound therapy. In addition, a high Curie temperature is desired because of wider temperature usage and improved temperature stability. Previous investigations have focused on Pb(Mg1/3Nb2/3)O3-PbTiO3 and Pb(Zn1/3Nb2/3)O3-PbTiO3 systems, which have a ultrahigh piezoelectric coefficient and dielectric constant, but a relatively low Curie temperature. It is desirable to study the binary relaxor-based system with a high Curie temperature. Therefore, Pb(In1/2Nb1/2)O3-PbTiO3 (PINT) single crystals were chosen to study the Mn-doped influence on their electrical properties and domain configuration. The evolution of ferroelectric hysteresis loops for doped and virgin samples exhibit the pinning effect in Mn-doped PINT crystals. The relaxation behaviors of doped and virgin samples are studied by fit of the modified Curie-Weiss law and Volgel-Fucher relation. In addition, a short-range correlation length was fitted to study the behavior of polar nanoregions based on the domain configuration obtained by piezoresponse force microscopy. Complex domain structures and smaller short-range correlation lengths (100-150 nm for Mn-doped PINT and >400 nm for pure PINT) were obtained in the Mn-doped PINT single crystals.

Low-Temperature Catalytic Decomposition of 130 Tetra- to Octa-PCDD/Fs Congeners over CuOX and MnOX Modified V2O5/TiO2-CNTs with the Assistance of O3.

Science.gov (United States)

Zhao, Rixiao; Jin, Dongdong; Yang, Hangsheng; Lu, Shengyong; Potter, Phillip M; Du, Cuicui; Peng, Yaqi; Li, Xiaodong; Yan, Jianhua

2016-10-07

In this study, a reliable and steady PCDD/F generation system was utilized to investigate the performance of catalysts, in which 130 congeners of tetra- to octapolychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) vapors were studied under simulated flue gas with/without O 3 . TiO 2 and carbon nanotubes (CNTs) supported vanadium oxides (VO X /TiO 2 -CNTs) modified with MnO X and CuO X , which were reported to be beneficial to the decomposition of model molecules, were found to have a negative effect on the removal of real PCDD/Fs in the simulated flue gas without O 3 . Moreover, the addition of MnO X presented different effects depending on whether CuO X existed in catalysts or not, which was also contrary to its effects on the degradation of model molecules. In an O 3 -containing atmosphere, low chlorination level PCDD/Fs congeners were removed well over VO X -MnO X /TiO 2 -CNTs, while high chlorination level PCDD/Fs congeners were removed well over VO X -CuO X /TiO 2 -CNTs. Fortunately, all PCDD/Fs congeners decomposed well over VO X -MnO X -CuO X /TiO 2 -CNTs. Finally, the effects of tetra- to octachlorination level for the adsorption and degradation behaviors of PCDD/Fs congeners were also investigated.

Charge driven metal-insulator transitions in LaMnO3|SrTiO3 (111) superlattices

KAUST Repository

Cossu, Fabrizio; Tahini, Hassan Ali; Singh, Nirpendra; Schwingenschlö gl, Udo

2017-01-01

Interfaces of perovskite oxides, due to the strong interplay between the lattice, charge and spin degrees of freedom, can host various phase transitions, which is particularly interesting if these transitions can be tuned by external fields. Recently, ferromagnetism was found together with a seemingly insulating state in superlattices of manganites and titanates. We therefore study the (111) oriented $(\\text{LaMnO}_3)_{6-x}\\vert(\\text{SrTiO}_3)_{6+x}~(x = -0.5, 0, 0.5)$ superlattices by means of ab initio calculations, predicting a ferromagnetic ground state due to double exchange in all cases. We shed light on the ferromagnetic coupling in the LaMnO3 region and at the interfaces. The insulating states of specific superlattices can be understood on the basis of Jahn-Teller modes and electron/hole doping.

Charge driven metal-insulator transitions in LaMnO3|SrTiO3 (111) superlattices

KAUST Repository

Cossu, Fabrizio

2017-08-01

Interfaces of perovskite oxides, due to the strong interplay between the lattice, charge and spin degrees of freedom, can host various phase transitions, which is particularly interesting if these transitions can be tuned by external fields. Recently, ferromagnetism was found together with a seemingly insulating state in superlattices of manganites and titanates. We therefore study the (111) oriented $(\\\\text{LaMnO}_3)_{6-x}\\\\vert(\\\\text{SrTiO}_3)_{6+x}~(x = -0.5, 0, 0.5)$ superlattices by means of ab initio calculations, predicting a ferromagnetic ground state due to double exchange in all cases. We shed light on the ferromagnetic coupling in the LaMnO3 region and at the interfaces. The insulating states of specific superlattices can be understood on the basis of Jahn-Teller modes and electron/hole doping.

Characterization of Li4Ti5O12 and LiMn2O4 spinel materials treated with aqueous acidic solutions

NARCIS (Netherlands)

Simon, D.R.

2007-01-01

In this thesis an investigation of two spinel materials, Li4Ti5O12 and LiMn2O4 used for Li-ion battery applications is performed interms of formation and reactivity towards acidic solutions. Subsequent characterizations such as structural, magnetic, chemical, and electrochemical characterizations

High-pressure studies on electronic and mechanical properties of FeBO3 (B = Ti, Mn, Cr) ceramics - a first-principles study

Science.gov (United States)

Kishore, N.; Nagarajan, V.; Chandiramouli, R.

2018-04-01

Using the density functional theory (DFT) method, the electronic and mechanical properties of perovskites FeBO3 (B = Ti, Mn, Cr) nanostructures were studied in the pressure range of 0-100 GPa. The band structure studies show the change in the band structure upon substitution of different B cation in FeBO3 perovskite structure. The density of states spectrum gives the perception of change in the electronic properties of FeBO3 with the substitution of B cation. The bulk, shear and Young's moduli were calculated and an increase in the moduli is noticed. Moreover, the hardness increases under high pressure. The high-pressure studies of FeBO3 perovskite nanostructures are explored at atomistic level. The findings show that ductility and hardness of FeBO3 get increased upon an increase in the applied pressure. The substitution of Ti, Mn and Cr on FeBO3 shows a significant change in the electronic and mechanical properties.

Effects of thermo-mechanical treatment and microalloying with Cr, Nb and Ti on phase transformation in C-Mn steel strips produced by compact strip production process

International Nuclear Information System (INIS)

Zhu, Y.Z.; Liang, D.M.; Li, J.C.; Xu, J.P.; Xue, Z.L.

2011-01-01

Highlights: → The order of solid solution of carbides influences phase transformation of C-Mn steel in cooling. → Evidences of early stage of solid solution of carbides were provides in the paper. → Transitional state evidences such as carbon enriched regions were observed in this study. - Abstract: The C-Mn steel strips microalloyed with Cr, Nb, Ti was produced by compact strip production process and then heat-treated under different conditions. Optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and transmission electron microscopy were used to investigate phase transformations in the steel after different treatments. It was revealed that the phase transformations upon quenching were greatly affected by the austenization temperature and time. When the steel was annealed at 950 deg. C, carbides of Cr, Mn and Fe were dissolved dramatically, while carbides of Nb and Ti are relatively stable at this temperature. When the temperature increases to 1100 deg. C, the carbides of Nb were dissolved rapidly, while the carbides of Ti still show somewhat stable (partial dissolution). Annealing time influences both the amount and the shapes of carbides in the steel, which leads to different phase transformations in the following air cooling processes. Grain growth in the steel in annealing process strongly depends on the dissolution of carbides on grain boundaries. Additionally, a subsequent rolling after annealing treatment at 950 deg. C lead to obvious precipitation of carbides of Ti and Nb in the steel.

Strain-mediated magnetic response in La0.67Sr0.33MnO3/SrTiO3/La0.67Sr0.33MnO3/BaTiO3 structure

Science.gov (United States)

Swain, Anupama; Komatsu, Katsuyoshi; Itoh, Mitsuru; Taniyama, Tomoyasu; Gorige, Venkataiah

2018-05-01

Electric field controlled magnetism is an exciting area of condensed matter physics to explore the device applications at ultra-low power consumption compared to the conventional current controlled or magnetic field controlled devices. In this study, an attempt was made to demonstrate electric field controlled magnetoresistance (MR) in a tri-layer structure consisting of La0.67Sr0.33MnO3 (LSMO) (40 nm)/SrTiO3 (10 nm)/LSMO (10 nm) grown on a 500-μm-thick BaTiO3 (001) (BTO) single crystal substrate by pulsed laser deposition technique. Epitaxial growth of the trilayer structure was confirmed by x-ray diffraction measurements. Jumps observed in the temperature-dependent magnetization curve at around the structural phase transitions of BTO ensure the strain-mediated magnetoelectric coupling between LSMO and BTO layers. A significant change in MR of this structure in applied electric fields does not show any polarity dependence. The findings are related to the lattice strain-mediated magnetoelectric coupling in ferromagnetic LSMO/ferroelectric BTO heterostructures.

Initial oxidation of TiFe{sub 1−x}Mn{sub x} (x = 0–0.3) by low dose exposures to H{sub 2}O and O{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Shwartz, A. [Ben-Gurion University of the Negev, P.O. Box 653, Beer-Sheva 84105 (Israel); Shamir, N., E-mail: noah.shamir@gmail.com [Nuclear research Center – Negev, P.O. Box 9001, Beer-Sheva 84190 (Israel); Froumin, N. [Ben-Gurion University of the Negev, P.O. Box 653, Beer-Sheva 84105 (Israel); Zalkind, S.; Edry, I.; Haim, A. [Nuclear research Center – Negev, P.O. Box 9001, Beer-Sheva 84190 (Israel); Mintz, M.H. [Ben-Gurion University of the Negev, P.O. Box 653, Beer-Sheva 84105 (Israel); Nuclear research Center – Negev, P.O. Box 9001, Beer-Sheva 84190 (Israel)

2014-10-15

Highlights: • Thermodynamics of adsorption and initial oxidation of TiFe{sub 1−x}Mn{sub x} by H{sub 2}O versus O{sub 2}. • Explanation of different oxide formations. • Explanation of the role of the different constituents of the alloys in the processes. - Abstract: The very initial room-temperature oxidation processes of the ternary pseudo-binary TiFe{sub 1−x}Mn{sub x} (x = 0–0.3) intermetallics by trace amounts of H{sub 2}O vapor and O{sub 2} were studied utilizing XPS and AES techniques. Different reactivities of the two gases were obtained, with a lower oxidation ability of H{sub 2}O, relative to O{sub 2}, as anticipated from thermodynamic considerations. The exposure to O{sub 2} results in a two stage oxidation of the Ti ingredient, which first converts into a divalent TiO (up to exposures of about 2 L), then proceeds into a tetravalent TiO{sub 2} form. Unlike oxygen, water exposure produces only the divalent oxide through the whole exposure range studied (11 L). The Mn component in these compounds is oxidized only by O{sub 2} and not by H{sub 2}O. The Fe ingredient is not oxidized at all and remains in its metallic form up to exposures of 30 L.

Characterization and concentration of manganese ore waste; Caracterizacao e concentracao de rejeito de minerio de manganes

Energy Technology Data Exchange (ETDEWEB)

Lima, Rosa Malena Fernandes; Pereira, Eder Esper; Reis, Erica Linhares; Silva, Glaucia Regina da [Universidade Federal de Ouro Preto (UFOP), MG (Brazil)

2010-07-01

In this work is presented the tests results of characterization and concentration by gravity and flotation methods carried out with a manganese sample waste. By optical microscopy, SEM/EDS and X-ray diffractometry were identified the Mn minerals spessartite (20%), tephroite (15%), rhodonite (5%), rhodochrosite and carbonates minerals (29%), opaque minerals and others (16%), micaceus minerals (6%) and quartz (4%). It was obtained Mn metallurgical recovery of 58% with Mn concentrate contents varying from 30 to 32.5%. The concentrates SiO{sub 2} contents of flotation were until 1.5% smaller than those contents of gravity method concentrates. (author)

Characterization and concentration of manganese ore waste

International Nuclear Information System (INIS)

Lima, Rosa Malena Fernandes; Pereira, Eder Esper; Reis, Erica Linhares; Silva, Glaucia Regina da

2010-01-01

In this work is presented the tests results of characterization and concentration by gravity and flotation methods carried out with a manganese sample waste. By optical microscopy, SEM/EDS and X-ray diffractometry were identified the Mn minerals spessartite (20%), tephroite (15%), rhodonite (5%), rhodochrosite and carbonates minerals (29%), opaque minerals and others (16%), micaceus minerals (6%) and quartz (4%). It was obtained Mn metallurgical recovery of 58% with Mn concentrate contents varying from 30 to 32.5%. The concentrates SiO_2 contents of flotation were until 1.5% smaller than those contents of gravity method concentrates. (author)

Oxygen-storage behavior and local structure in Ti-substituted YMnO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Levin, I., E-mail: igor.levin@nist.gov [National Institute of Standards and Technology, Gaithersburg, MD 20899 (United States); Krayzman, V.; Vanderah, T.A. [National Institute of Standards and Technology, Gaithersburg, MD 20899 (United States); Tomczyk, M. [Department of Ceramics and Glass Engineering, University of Aveiro, Aveiro 3810-193 (Portugal); Wu, H. [National Institute of Standards and Technology, Gaithersburg, MD 20899 (United States); Tucker, M.G. [Spallation Neutron Source, Oak Ridge National Laboratory, Oak Ridge, TN (United States); Playford, H.Y. [ISIS Facility, Rutherford Appleton Laboratory, Didcot, Oxford (United Kingdom); Woicik, J.C.; Dennis, C.L. [National Institute of Standards and Technology, Gaithersburg, MD 20899 (United States); Vilarinho, P.M. [Department of Ceramics and Glass Engineering, University of Aveiro, Aveiro 3810-193 (Portugal)

2017-02-15

Hexagonal manganates RMnO{sub 3} (R=Y, Ho, Dy) have been recently shown to exhibit oxygen-storage capacities promising for three-way catalysts, air-separation, and related technologies. Here, we demonstrate that Ti substitution for Mn can be used to chemically tune the oxygen-breathing properties of these materials towards practical applications. Specifically, Y(Mn{sub 1−x}Ti{sub x})O{sub 3} solid solutions exhibit facile oxygen absorption/desorption via reversible Ti{sup 3+}↔Ti{sup 4+} and Mn{sup 3+}↔Mn{sup 4+} reactions already in ambient air at ≈400 °C and ≈250 °C, respectively. On cooling, the oxidation of both cations is accompanied by oxygen uptake yielding a formula YMn{sup 3+}{sub 1−x-y}Mn{sup 4+}{sub y}Ti{sup 4+}{sub x}O{sub 3+δ}. The presence of Ti promotes the oxidation of Mn{sup 3+} to Mn{sup 4+}, which is almost negligible for YMnO{sub 3} in air, thereby increasing the uptake of oxygen beyond that required for a given Ti{sup 4+} concentration. The reversibility of the redox reactions is limited by sluggish kinetics; however, the oxidation process continues, if slowly, even at room temperature. The extra oxygen atoms are accommodated by the large interstices within a triangular lattice formed by the [MnO{sub 5}] trigonal bipyramids. According to bond distances from Rietveld refinements using the neutron diffraction data, the YMnO{sub 3} structure features under-bonded Mn and even more severely under-bonded oxygen atoms that form the trigonal bases of the [MnO{sub 5}] bipyramids. The tensile bond strain around the 5-fold coordinated Mn site and the strong preference of Ti{sup 4+}(and Mn{sup 4+}) for higher coordination numbers likely provide driving forces for the oxidation reaction. Reverse Monte Carlo refinements of the local atomic displacements using neutron total scattering revealed how the excess oxygen atoms are accommodated in the structure by correlated local displacements of the host atoms. Large displacements of the under

Catalytic Oxidation of Propene over Pd Catalysts Supported on CeO2, TiO2, Al2O3 and M/Al2O3 Oxides (M = Ce, Ti, Fe, Mn

Directory of Open Access Journals (Sweden)

Sonia Gil

2015-04-01

Full Text Available In the following work, the catalytic behavior of Pd catalysts prepared using different oxides as support (Al2O3, CeO2 and TiO2 in the catalytic combustion of propene, in low concentration in excess of oxygen, to mimic the conditions of catalytic decomposition of a volatile organic compound of hydrocarbon-type is reported. In addition, the influence of different promoters (Ce, Ti, Fe and Mn when added to a Pd/Al2O3 catalyst was analyzed. Catalysts were prepared by the impregnation method and were characterized by ICP-OES, N2 adsorption, temperature-programmed reduction, temperature-programmed oxidation, X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. Catalyst prepared using CeO2 as the support was less easily reducible, due to the stabilization effect of CeO2 over the palladium oxides. Small PdO particles and, therefore, high Pd dispersion were observed for all of the catalysts, as confirmed by XRD and TEM. The addition of Ce to the Pd/Al2O3 catalysts increased the metal-support interaction and the formation of highly-dispersed Pd species. The addition of Ce and Fe improved the catalytic behavior of the Pd/Al2O3 catalyst; however, the addition of Mn and Ti decreased the catalytic activity in the propene oxidation. Pd/TiO2 showed the highest catalytic activity, probably due to the high capacity of this catalyst to reoxidize Pd into PdO, as has been found in the temperature-programmed oxidation (TPO experiments.

Soft antiphase tilt of oxygen octahedra in the hybrid improper multiferroic Ca3Mn1.9Ti0.1O7

Science.gov (United States)

Ye, Feng; Wang, Jinchen; Sheng, Jieming; Hoffmann, C.; Gu, T.; Xiang, H. J.; Tian, Wei; Molaison, J. J.; dos Santos, A. M.; Matsuda, M.; Chakoumakos, B. C.; Fernandez-Baca, J. A.; Tong, X.; Gao, Bin; Kim, Jae Wook; Cheong, S.-W.

2018-01-01

We report a single crystal neutron and x-ray diffraction study of the hybrid improper multiferroic Ca3Mn1.9Ti0.1O7 (CMTO), a prototypical system where the electric polarization arises from the condensation of two lattice distortion modes. With increasing temperature (T ), the out-of-plane, antiphase tilt of MnO6 decreases in amplitude while the in-plane, in-phase rotation remains robust and experiences abrupt changes across the first-order structural transition. Application of hydrostatic pressure (P ) to CMTO at room temperature shows a similar effect. The consistent behavior under both T and P reveals the softness of antiphase tilt and highlights the role of the partially occupied d orbital of the transition-metal ions in determining the stability of the octahedral distortion. Polarized neutron analysis indicates the symmetry-allowed canted ferromagnetic moment is less than the 0.04 μB/Mn site, despite a substantial out-of-plane tilt of the MnO6 octahedra.

Microstructural characterization of the γ-TiAl alloy samples ...

Indian Academy of Sciences (India)

A direct laser fabrication technique (DLF) has been used to fabricate near net shape samples of a -TiAl alloy using gas atomized Ti48A148Mn2Nb2 alloy powder as a feed stock material. The microstructures of these Ti48Al48Mn2Nb2 laser treated samples have been characterized using optical, scanning (SEM) and ...

Microstructure and fracture toughness of Mn-stabilized cubic titanium trialuminide

Science.gov (United States)

Zbroniec, Leszek Ireneusz

This thesis project is related to the fracture toughness aspects of the mechanical behavior of the selected Mn-modified cubic Ll2 titanium trialuminicles. Fracture toughness was evaluated using two specimen types: Single-Edge-Precracked-Beam (SEPB) and Chevron-Notched-Beam (CNB). The material tested was in cast, homogenized and HIP-ed condition. In the preliminary stage of the project due to lack of the ASTM Standard for fracture toughness testing of the chevron-notched specimens in bending the analyses of the CNB configuration were done to establish the optimal chevron notch dimensions. Two types of alloys were investigated: (a) boron-free and boron doped low-Mn (9at.% Mn), as well as (b) boron-free and boron-doped high-Mn (14at.% Mn). Toughness was investigated in the temperature range from room temperature to 1000°C and was calculated from the maximum load. It has been found that toughness of coarse-grained "base" 9Mn-25Ti alloy exhibits a broad peak at the 200--500°C temperature range and then decreases with increasing temperature, reaching its room temperature value at 10000°C. However, the work of fracture (gammaWOF) and the stress intensity factor calculated from it (KIWOF) increases continuously with increasing temperature. Also the fracture mode dependence on temperature has been established. To understand the effect of environment on the fracture toughness of coarse-grained "base", boron-free 9Mn-25Ti alloy, the tests were carried out in vacuum (˜1.3 x 10-5 Pa), argon, oxygen, water and liquid nitrogen. It has been shown that fracture toughness at ambient temperature is not affected by the environments containing moisture (water vapor). It seems that at ambient temperatures these materials are completely immune to the water-vapor hydrogen embrittlement and their cause of brittleness is other than environment. To explore the influence of the grain size on fracture toughness the fracture toughness tests were also performed on the dynamically

The mechanism of formation of a fine duplex microstructure in Ti-48Al-2Mn-2Nb alloys

International Nuclear Information System (INIS)

Ramanujan, R.V.; Maziasz, P.J.

1996-01-01

The mechanism of formation of the fine duplex microstructure resulting from the α → γ transformation in water-quenched Ti-48Al-2Mn-2Nb alloys was studied using transmission and analytical electron microscopy. As-cast Ti-48Al-2Mn-2Nb alloys were heat treated in the α phase field and water quenched to room temperature. The resulting microstructure (referred to as a fine duplex microstructure) consisted of equiaxed grains and abutting lath colonies. Both the colonies and the grains were composed of the γ phase, twinned γ laths, and α 2 laths. It was found that the transformation from α to γ in the fine duplex microstructure took place through long range diffusional processes, and competitive growth between the equiaxed and lath morphology occurred. Nucleation of the γ phase from the α matrix can occur through nucleation on stacking faults, followed by growth through the sympathetic nucleation and growth of new γ laths on a substrate lath. The observed misorientations and the interfacial structures between the laths were found to be consistent with such a mechanism. Competition between such nucleation and growth mechanisms for the equiaxed and lath morphologies of γ leads to the formation of lath colonies (of γ and α 2 ) interspersed with equiaxed grains in these alloys

Structural characterization and electrochemical behaviour of Li{sub (4−x)/3}Ti{sub (5−2x)/3}Mn{sub x}O{sub 4} solid solution with spinel-structure

Energy Technology Data Exchange (ETDEWEB)

Martín, P., E-mail: pmartinp@quim.ucm.es; López, M.L.; Pico, C.; Veiga, M.L.

2013-07-15

A series of new oxides Li{sub (4−x)/3}Ti{sub (5−2x)/3}Mn{sub x}O{sub 4} (0.1 ≤ x ≤ 0.9) have been synthesized by solid state reactions and characterized by thermal analysis and X-ray and neutron diffraction. In all phases, Li{sup +} cations mainly occupy tetrahedral sites and transition metals cations are located on the octahedral ones. These phases show a structural disorder–order transition associated to the proportion of manganese in the samples and to its oxidation state. All these factors have a marked influence on the electrochemical properties and the phase x = 0.1 shows the best characteristics to be used as anode in a solid state battery. - Highlights: • Lithium spinels anodes in batteries. • Influence of Ti/Mn ratio in the electrochemical behaviour. • Li{sub 1.3}Ti{sub 1.6}Mn{sub 0.1}O{sub 4}: a promising zero-strain material. • Influence of disorder–order transitions on the physical properties.

Photoionization study of Ne-like K9+, Ca10+, Sc11+, Ti12+, V13+, Cr14+, Mn15+, and Fe16+ ions using the screening constant by unit nuclear charge method

International Nuclear Information System (INIS)

Goyal, Arun; Khatri, Indu; Sow, Malick; Sakho, Ibrahima; Aggarwal, Sunny; Singh, A.K.; Mohan, Man

2016-01-01

Photoionization of the 2s 2 2p 6 ( 1 S 0 ) ground state of the Ne-like (Z=19–29) ions is presented in this paper. Resonance energies and total natural width of the 2s2p 6 np 1 P series of the Ne-like K 9+ , Ca 10+ , Sc 11+ , Ti 12+ , V 13+ , Cr 14+ , Mn 15+ , and Fe 16+ are reported. All the calculations are made using the Screening constant by unit nuclear charge (SCUNC) formalism. New data for Ne-like K 9+ , Sc 11+ , Ti 12+ , V 13+ , Cr 14+ , and Mn 15+ ions are tabulated. Good agreements are found with available literature data. - Highlights: • Photoionization of ground state of the Ne-like (Z=19–29) presented. • good agreements with scarce literature data. • New data for Ne-like K 9+ , Sc 11+ , Ti 12+ , V 13+ , Cr 14+ , and Mn 15+ ions. • Useful guidelines for application in laboratory, astrophysics, and plasma physics.

Site preference and phase stability of Ti doping Ni–Mn–Ga shape memory alloys from first-principles calculations

International Nuclear Information System (INIS)

Gao, Zhiyong; Chen, Baishu; Meng, Xianglong; Cai, Wei

2013-01-01

Highlights: •Site preference and phase stability of NiMnGaTi are studied by first-principles. •The Ti atoms prefer to occupy the Ga sites in the Ni 2 MnGa austenitic phase. •The phase stability becomes worse when Ga is replaced by Ti. •The phase stability is discussed based on the densities of states. -- Abstract: The effects of Ti content on martensitic transformation and phase stability of Ni 50 Mn 25 Ga 25−x Ti x shape memory alloys were investigated from first-principles calculations based on density functional theory. The formation energy results indicate that the added Ti preferentially occupies the Ga sites in Ni 2 MnGa alloy due to the lowest formation energy. The total energy difference between austenite and martensite increases with Ti alloying, being relevant to the experimentally reported changes in martensitic transformation temperature. The phase stability of Ni 50 Mn 25 Ga 25−x Ti x austenite decreases with increasing Ti content, which results from the reduced Ni 3d–Mn 3d hybridization when Ga is replaced by Ti

Effects of Mn doping on the ferroelectric properties of PZT thin films

International Nuclear Information System (INIS)

Zhang Qi

2004-01-01

The effects of Mn doping on the ferroelectric properties of Pb(Zr 0.3 Ti 0.7 )O 3 (PZT) thin films on Pt/Ti/SiO 2 /Si substrates have been investigated. The composition of the PZT and Mn doping level are Pb(Zr 0.3 Ti 0.7 ) 1-x Mn x O 3 (x = 0,0.2,0.5,1,2,4 mol%). The PZT thin films doped with a small amount of Mn 2+ (x ≤ 1) showed almost no hysteretic fatigue up to 10 10 switching bipolar pulse cycles, coupled with excellent retention properties. However, excessive additions of manganese made the fatigue behaviour worse. We propose that the addition of small amounts of Mn is able to reduce the oxygen vacancy concentration due to the combination of Mn 2+ and oxygen vacancies in PZT films, forming Mn 4+ ions. The interfacial layer between the Pt electrode and PZT films and Mn-doped PZT (x = 4) was detected by measuring the dielectric constant of thin films of different thickness. However, this interfacial layer was not detected in Mn-doped PZT (x = 1). These observations support the concept of the preferential electromigration of oxygen vacancies into sites in planes parallel to the electrodes, which is probably responsible for the hysteretic fatigue

Pb(Zr,Ti)O3-Pb(Mn1/3Nb2/3)O3 piezoelectric thick films by aerosol deposition

International Nuclear Information System (INIS)

Ryu, Jungho; Choi, Jong-Jin; Hahn, Byung-Dong; Yoon, Woon-Ha; Lee, Byoung-Kuk; Choi, Joon Hwan; Park, Dong-Soo

2010-01-01

Piezoelectric thick films of Pb(Zr,Ti)O 3 -Pb(Mn 1/3 Nb 2/3 )O 3 (PZT-PMnN) with Zr:Ti ratios ranging from 0.45:0.55 to 0.60:0.40 were fabricated on a platinized silicon wafer by aerosol deposition (AD). All the films were deposited with a thickness of 10 μm with high density. By adding PMnN to 57:43 PZT, a dielectric constant as low as ∼660 was achieved while the effective piezoelectric constant was over 140 pC/N. PZT-PMnN with a Zr:Ti ratio of 57:43 thus showed a maximum piezoelectric voltage constant (g 33 ) of 23.8 x 10 -3 Vm/N and is a good candidate for high quality thick films for application to high-energy density or high sensitivity, piezoelectric energy harvesters and sensors.

Variations in the microstructure and properties of Mn-Ti multiple-phase steel with high strength under different tempering temperatures

Science.gov (United States)

Li, Dazhao; Li, Xiaonan; Cui, Tianxie; Li, Jianmin; Wang, Yutian; Fu, Peimao

2015-03-01

There are few relevant researches on coils by tempering, and the variations of microstructure and properties of steel coil during the tempering process also remain unclear. By using thermo-mechanical control process(TMCP) technology, Mn-Ti typical HSLA steel coils with yield strength of 920 MPa are produced on the 2250 hot rolling production line. Then, the samples are taken from the coils and tempered at the temperatures of 220 °C, 350 °C, and 620 °C respectively. After tempering the strength, ductility and toughness of samples are tested, and meanwhile microstructures are investigated. Precipitates initially emerge inside the ferrite laths and the density of the dislocation drops. Then, the lath-shaped ferrites begin to gather, and the retained austenite films start to decompose. Finally, the retained austenite films are completely decomposed into coarse and short rod-shape precipitates composed of C and Ti compounds. The yield strength increases with increasing tempering temperature due to the pinning effect of the precipitates, and the dislocation density decreases. The yield strength is highest when the steel is tempered at 220 °C because of pinning of the precipitates to dislocations. The total elongation increases in all samples because of the development of ferrites during tempering. The tensile strength and impact absorbed energy decline because the effect of impeding crack propagation weakens as the retained austenite films completely decompose and the precipitates coarsen. This paper clarifies the influence of different tempering temperatures on phase transformation characteristics and process of Mn-Ti typical multiphase steels, as well as its resulting performance variation rules.

Stable Water Oxidation in Acid Using Manganese-Modified TiO2 Protective Coatings.

Science.gov (United States)

Siddiqi, Georges; Luo, Zhenya; Xie, Yujun; Pan, Zhenhua; Zhu, Qianhong; Röhr, Jason A; Cha, Judy J; Hu, Shu

2018-06-06

Accomplishing acid-stable water oxidation is a critical matter for achieving both long-lasting water-splitting devices and other fuel-forming electro- and photocatalytic processes. Because water oxidation releases protons into the local electrolytic environment, it becomes increasingly acidic during device operation, which leads to corrosion of the photoactive component and hence loss in device performance and lifetime. In this work, we show that thin films of manganese-modified titania, (Ti,Mn)O x , topped with an iridium catalyst, can be used in a coating stabilization scheme for acid-stable water oxidation. We achieved a device lifetime of more than 100 h in pH = 0 acid. We successfully grew (Ti,Mn)O x coatings with uniform elemental distributions over a wide range of manganese compositions using atomic layer deposition (ALD), and using X-ray photoelectron spectroscopy, we show that (Ti,Mn)O x films grown in this manner give rise to closer-to-valence-band Fermi levels, which can be further tuned with annealing. In contrast to the normally n-type or intrinsic TiO 2 coatings, annealed (Ti,Mn)O x films can make direct charge transfer to a Fe(CN) 6 3-/4- redox couple dissolved in aqueous electrolytes. Using the Fe(CN) 6 3-/4- redox, we further demonstrated anodic charge transfer through the (Ti,Mn)O x films to high work function metals, such as iridium and gold, which is not previously possible with ALD-grown TiO 2 . We correlated changes in the crystallinity (amorphous to rutile TiO 2 ) and oxidation state (2+ to 3+) of the annealed (Ti,Mn)O x films to their hole conductivity and electrochemical stability in acid. Finally, by combining (Ti,Mn)O x coatings with iridium, an acid-stable water-oxidation anode, using acid-sensitive conductive fluorine-doped tin oxides, was achieved.

A Model for Creep and Creep Damage in the γ-Titanium Aluminide Ti-45Al-2Mn-2Nb.

Science.gov (United States)

Harrison, William; Abdallah, Zakaria; Whittaker, Mark

2014-03-14

Gamma titanium aluminides (γ-TiAl) display significantly improved high temperature mechanical properties over conventional titanium alloys. Due to their low densities, these alloys are increasingly becoming strong candidates to replace nickel-base superalloys in future gas turbine aeroengine components. To determine the safe operating life of such components, a good understanding of their creep properties is essential. Of particular importance to gas turbine component design is the ability to accurately predict the rate of accumulation of creep strain to ensure that excessive deformation does not occur during the component's service life and to quantify the effects of creep on fatigue life. The theta (θ) projection technique is an illustrative example of a creep curve method which has, in this paper, been utilised to accurately represent the creep behaviour of the γ-TiAl alloy Ti -45Al-2Mn-2Nb. Furthermore, a continuum damage approach based on the θ-projection method has also been used to represent tertiary creep damage and accurately predict creep rupture.

Improving low-temperature performance of spinel LiNi0.5Mn1.5O4 electrode and LiNi0.5Mn1.5O4/Li4Ti5O12 full-cell by coating solid-state electrolyte Li-Al-Ti-P-O

Science.gov (United States)

Bi, Kun; Zhao, Shi-Xi; Huang, Chao; Nan, Ce-Wen

2018-06-01

Octahedral cathode materials LiNi0.5Mn1.5O4 (LNMO), with primary particles size of 300-600 nm are prepared through one-step co-precipitation. Then solid-state electrolyte Li2O-Al2O3-TiO2-P2O5 (LATP) was coated on LNMO to form continuous surface-modification layer. There is no obviously difference of structure, morphology between coated LATP LiNi0.5Mn1.5O4 (LATP-LNMO) and pristine LiNi0.5Mn1.5O4 (P-LNMO). Low-temperature electrochemical performance of P-LNMO and LATP-LNMO electrodes, including charge-discharge capacity, cycle performance, middle discharge voltage and electrochemical impedance spectra (EIS), were measured systematically with three electrode. The results reveal that LATP-LNMO electrode presents superior electrochemical performance at low temperature, compared to P-LNMO electrode. At -20 °C, the capacity retention of LATP-LNMO (61%) is much higher than that of P-LNMO (39%). According to EIS, the enhancement of performance of LATP-LNMO cathode at low temperature can be attribute to LATP coating, which not only promotes lithium-ion diffusion at electrode/electrolyte interface but also decreases the charge transfer resistance. Finally, the electrochemical performances of full cell of LATP-LNMO or P-LNMO cathode vs Li4Ti5O12 anode are investigated. The energy density can be achieved to 270 Wh·Kg-1 at -20 °C if using LATP-LNMO, which is much better than that of P-LNMO.

Tuning magnetic critical behaviour in Ti-manganites by doping with vacancies in A-sites: Sr{sub 1-x}{open_square}{sub x}LaMnTiO{sub 6-{delta}} (0 < x {<=} 0.15)

Energy Technology Data Exchange (ETDEWEB)

Alonso-Dominguez, D., E-mail: danielad@quim.ucm.es [Dpto. Quimica Inorganica I, Facultad Ciencias Quimicas, Universidad Complutense de Madrid, E-28040 Madrid (Spain); Alvarez-Serrano, I. [Dpto. Quimica Inorganica I, Facultad Ciencias Quimicas, Universidad Complutense de Madrid, E-28040 Madrid (Spain); Cuello, G. [Institut Laue-Langevin, 6 rue Jules Horowitz, F-38042 Grenoble (France); Garcia-Hernandez, M. [Instituto de Ciencia de Materiales de Madrid, Consejo Superior de Investigaciones Cientificas, E-28049 Cantoblanco, Madrid (Spain); Lopez, M.L.; Pico, C.; Veiga, M.L. [Dpto. Quimica Inorganica I, Facultad Ciencias Quimicas, Universidad Complutense de Madrid, E-28040 Madrid (Spain)

2011-10-17

Highlights: {yields} Pure polycrystalline powders of Sr{sub 1-x}{open_square}{sub x}LaMnTiO{sub 6-{delta}} perovskites have been synthesized by the liquid mix technique. {yields} X-ray and neutron diffraction data, together with HRTEM are interpreted in terms of tetragonal symmetry and S.G. I4/mcm, being all the cations located at random in each sublattice. {yields} Magnetization measurements show the existence of a frustrated behaviour, implying FM interactions at low temperatures, and semiconductor behaviour is observed in the whole temperature range explored. {yields} The introduction of vacancies in the A sites is connected to the stabilization of the Griffiths phase for x < 0.15, and an electronic model considering a cluster glass picture is proposed. - Abstract: Microcrystalline powders of Sr{sub 1-x}{open_square}{sub x}LaMnTiO{sub 6-{delta}} (0 {<=} x {<=} 0.15) perovskites have been synthesized by the sol-gel method. Structural characterization from neutron diffraction data shows tetragonal symmetry for all samples in the whole temperature range explored (5-700 K) and HRTEM analysis confirms it at the micro scale. Structural refinements suggest that Sr/La and Mn/Ti cations are placed at random in A and B sublattices, respectively, being the vacancies exclusively located on the former sites. Doping with vacancies in the A sites does not provoke any extra structural ordering or distortion but modifies the electronic scenario at the B-sites, leading to an enhancement of Griffiths phase as the amount of vacancies, x, increases. Semiconductor behaviour has been observed, without any transition to metallic state, with typical activation energies of 0.15 eV. The intrinsic magnetic frustrated behaviour is described in terms of a cluster-glass model.

Thermodynamics of oxygen solutions in Fe-40% Ni-15% Cr melts containing Mn, Si, Ti, Al

International Nuclear Information System (INIS)

Dashevskij, V.Ya.; Makarova, N.N.; Grigorovich, K.V.; Kashin, V.I.; Polikarpova, N.V.

2000-01-01

Thermodynamic analysis and experimental studied are performed for oxygen solutions in Fe-40% Ni-15% Cr melts where Mn, Si, Ti, Al are used as reducing agents. It is revealed that in the alloys studied the affinity of reducing agents to oxygen essentially lower than in liquid iron, nickel and Fe-40% Ni alloy. This is explained by the fact that the oxygen activity in melts noticeably decreases due to a high chromium content whereas the activity of reducing elements increases in a rather less degree. The agreement between analytical and experimental results confirms the validity of the calculation technique [ru

Study of multiplet structures of Mn4+ activated in fluoride crystals

International Nuclear Information System (INIS)

Novita, Mega; Honma, Tetsuo; Hong, Byungchul; Ohishi, Atsushi; Ogasawara, Kazuyoshi

2016-01-01

We investigated the optical properties of Mn 4+ in some fluoride crystals such as Cs 2 MnF 6 , Cs 2 GeF 6 , Rb 2 GeF 6 , Cs 2 SiF 6 , K 2 SiF 6 , Rb 2 MnF 6 , Rb 2 SiF 6 , K 2 GeF 6 , K 2 TiF 6 , Li 2 MnF 6 , Na 2 GeF 6 , Na 2 SiF 6 , and Na 2 TiF 6 based on the first-principle calculation using the discrete-variational multi-electron method. In order to estimate the lattice relaxation, we performed EXAFS measurement of Mn 4+ doped in K 2 SiF 6 , K 2 TiF 6 , and K 2 GeF 6 . The relaxation rates of A 2 BF 6 :Mn 4+ were fixed to be the above estimated values, 102.24%, 107.37% or 96.80% for crystal having Si, Ge, or Ti at the B cation site, respectively. In this work, we also considered some corrections such as configuration dependent correction and correlation correction to improve the theoretical energies. It has been shown that to reproduce multiplet energy levels quantitatively, the lattice relaxation is very important. On the other hand, for a qualitative prediction of the tendencies of the multiplet energies, the combination of lattice relaxation effect, configuration dependent correction, and correlation correction is effective. - Highlights: • Multiplet structures of A 2 BF 6 :Mn 4+ were calculated from first-principles. • Lattice relaxation was estimated based on EXAFS experiment. • Lattice relaxation is important to reproduce multiplet energies quantitatively. • CDC and CC are important to reproduce tendencies of multiplet energies.

Multi-walled carbon nanotubes functionalized by carboxylic groups: Activation of TiO{sub 2} (anatase) and phosphate olivines (LiMnPO{sub 4}; LiFePO{sub 4}) for electrochemical Li-storage

Energy Technology Data Exchange (ETDEWEB)

Kavan, Ladislav; Zukalova, Marketa [J. Heyrovsky Institute of Physical Chemistry, v.v.i., Academy of Sciences of the Czech Republic, Dolejskova 3, CZ-18223 Prague 8 (Czech Republic); Bacsa, Revathi; Tunckol, Meltem; Serp, Philippe [Laboratoire de Chimie de Coordination, UPR CNRS 8241, composante ENSIACET, Universite de Toulouse UPS-INP-LCC 4, Allee Emile Monso, BP 74233, 31432, Toulouse (France); Zakeeruddin, Shaik M.; Le Formal, Florian; Graetzel, Michael [Laboratoire de Photonique et Interfaces, EPFL, Ecublens, CH-1015 Lausanne (Switzerland)

2010-08-15

Multi-walled carbon nanotubes functionalized by carboxylic groups, exhibit better affinity towards TiO{sub 2} (P90, Degussa) as compared to that of pristine nanotubes. Also the electrochemical performance of TiO{sub 2} is improved by nanotube networking, but the Li-storage capacity of TiO{sub 2} is unchanged. Whereas the composite of TiO{sub 2} with non-functionalized nanotubes demonstrates simple superposition of the behavior of pure components, the composite with functionalized nanotubes shows unique faradaic pseudocapacitance which is specific for this composite only. The surface functionalization of nanotubes enhances charge storage capacity and reversibility of a composite with LiMnPO{sub 4} (olivine), but mediates also the electrolyte breakdown at potentials >4.2 V. Whereas the electrochemical activation of LiMnPO{sub 4} (olivine) by functionalized nanotubes is quite modest, excellent performance was found for LiFePO{sub 4} (olivine) in composite materials containing only 2 wt% of functionalized nanotubes. (author)

Structural characterization of PbTi03, Sm0.6Nd0.4NiO3 and NdMnO3 multifunctional Perovskite thin films

Directory of Open Access Journals (Sweden)

Rapenne L.

2012-06-01

Full Text Available Different multifunctional (PbTiO3, Sm0.6Nd0.4NiO3, NdMnO3 thin films were grown by metalorganic chemical vapor deposition (MOCVD technique on SrTiO3 and LaAlO3 substrates. TEM and X-ray diffraction measurements reveal that almost single crystalline thin films can be epitaxially grown on the top of substrates. The relationship between the crystallographic orientation of the films and those of the substrates were determined by reciprocal space mapping and TEM analyses. PbTi03 thin films appear to be under tensile or compressive strain according to the different mismatch of their cell parameter with those of the substrate. Relaxation mechanism as a function of the film thickness arises from coexistence of different type of domains and size and strain effect are analyzed. SmNiO3 thin films present diffuse scattering strikes and are less well organized when compared to PbTi03 thin films. Different domains are observed as well as an additional parasitic phase close to NiO. Its regular distribution can be associated to reduced transport properties. Preliminary observations on NdMnO3 thin films show that an amorphous phase is obtained during MOCVD that can be transformed in a single crystalline film by annealing. The films are under tensile or compressive strain according to the different mismatch of their cell parameter with those of the substrate. Magnetic properties are investigated.

Effect of variable thermal conductivity and specific heat capacity on the calculation of the critical metal hydride thickness for Ti1.1CrMn

DEFF Research Database (Denmark)

Mazzucco, Andrea; Rokni, Masoud

2014-01-01

model is applied to the metal hydride system, with Ti 1.1 CrMn as the absorbing alloy, to predict the weight fraction of absorbed hydrogen and solid bed temperat ure . Dependencies of thermal conductivity and specific heat capacity upon pressure and hydrogen content respectively , are accounted for...

Fabrication and Raman scattering of a core–shell structure based on Mn doped ZnO and barium titanate

International Nuclear Information System (INIS)

Sima, M.; Baibarac, M.; Vasile, E.; Sima, Ma.; Mihut, L.

2015-01-01

Graphical abstract: - Highlights: • ZnO/Zn_1_−_xMn_xO/BaTiO_3 nanorod array on FTO substrate. • Oxygen vacancies in the ZnO/Zn_1_−_xMn_xO nanostructure. • The interface between the ZnO/Zn_1_−_xMn_xO core and the BaTiO_3 shell without unwanted phases. - Abstract: A combination of chemical and thermal annealing techniques was used to prepare an array of ZnO/Zn_1_−_xMn_xO/BaTiO_3 nanorods. ZnO nanorod arrays were obtained by hydrothermal–electrochemical processes. The precursors for Zn_1_−_xMn_xO and BaTiO_3, prepared by sol–gel technique were deposited by spin coating on the surface of ZnO nanorods. Each deposition stage was accompanied by thermal treatment stages. Scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and photoluminescence spectroscopy reveal the presence of a film of Zn_1_−_xMn_xO with wurtzite structure on the surface of ZnO nanorods. Transmission electron microscopy images demonstrate that a layer of BaTiO_3 is deposited on the surface of each ZnO/Zn_1_−_xMn_xO core shell nanorod. BaTiO_3 film onto the ZnO/Zn_1_−_xMn_xO core shell nanorods is also evidenced in Raman scattering by broadening of the Raman band situated in the spectral range 500–750 cm"−"1.

Analysis of multiferroic properties in BiMnO3 thin films

International Nuclear Information System (INIS)

Grizalez, M; Mendoza, G A; Prieto, P

2009-01-01

Textured BiMnO 3 [111] thin films on SrTiO 3 (100) and Pt/TiO 2 /SiO 2 substrates were grown via r.f. magnetron sputtering (13.56 MHz). The XRD spectra confirmed a monoclinic structure and high-quality textured films for the BiMnO 3 films. The films grown on SrTiO 3 (100) showed higher crystalline quality than those developed on Pt/TiO 2 /SiO 2 . Through optimized oxygen pressure of 5x10 -2 mbar during the r.f. sputtering deposition, the crystalline orientation of the BiMnO 3 film was improved with respect to the previously reported value of 2x10 -1 mbar. The values of spontaneous polarization (P s ), remnant polarization (P r ), and coercive field (F c ) from ferroelectric hysteresis loops (P-E) at different temperatures were also obtained. Samples with higher crystalline order revealed better dielectric properties (high P s and P r values and a low F c ). For films on both types of substrates, the ferroelectric behavior was found to persist up to 400K. Measurements at higher temperatures were difficult to obtain given the increased conductivity of the films. Magnetic hysteresis loops from 5K to 120K were obtained for BiMnO 3 films grown on SrTiO 3 and Pt/TiO 2 /SiO 2 substrates. The results suggested that the coexistence of the magnetic and electric phases persists up to 120K.

Investigation of spin-gapless semiconductivity and half-metallicity in Ti2MnAl-based compounds

International Nuclear Information System (INIS)

Lukashev, P.; Staten, B.; Hurley, N.; Kharel, P.; Gilbert, S.; Fuglsby, R.; Huh, Y.; Valloppilly, S.; Zhang, W.; Skomski, R.; Sellmyer, D. J.; Yang, K.

2016-01-01

The increasing interest in spin-based electronics has led to a vigorous search for new materials that can provide a high degree of spin polarization in electron transport. An ideal candidate would act as an insulator for one spin channel and a conductor or semiconductor for the opposite spin channel, corresponding to the respective cases of half-metallicity and spin-gapless semiconductivity. Our first-principle electronic-structure calculations indicate that the metallic Heusler compound Ti 2 MnAl becomes half-metallic and spin-gapless semiconducting if half of the Al atoms are replaced by Sn and In, respectively. These electronic structures are associated with structural transitions from the regular cubic Heusler structure to the inverted cubic Heusler structure.

Favorable ultraviolet photoelectric effects in TbMnO3/Nb-SrTiO3 heterostructures

KAUST Repository

Jin, Kexin

2014-12-01

The rectifying properties and ultraviolet photoelectric effects in TbMnO3/Nb-doped SrTiO3 heterostructures have been investigated. The ideality factors and the diffusion voltages obtained from the current-voltage curves nonlinearly decrease with increasing the temperature. It is observed that the maximum photovoltaic values of the heterostructure irradiated by the 365 nm (2.6 mW/mm2) and 248 nm (0.71 mJ/mm2) lights are about 0.121 V and 0.119 V at T=300 K, respectively. The relations between the relaxation of photovoltages after the irradiation and the power intensity are revealed. These results suggest the potential applications in the development of ultraviolet detectors using oxides-based heterostructures.

Structural characterisation and physical properties of Li MMnO 4 ( M=Cr, Ti) spinels

Science.gov (United States)

Arillo, M. A.; Cuello, G.; López, M. L.; Martín, P.; Pico, C.; Veiga, M. L.

2005-01-01

New spinel-type phases of general formula Li MMnO 4 ( M=Cr, Ti), derived from LiMn 2O 4 by substitution of Mn 3+ by Cr 3+ or Mn 4+ by Ti 4+, have been obtained and characterised. Neutron diffraction refinements confirm that both phases crystallise in the Fd3m space group, giving the cation distributions [Li] 8 a[CrMn] 16 dO 4 and [Li 0.66Ti 0.34] 8 a[Li 0.34MnTi 0.66] 16 dO 4. Electrical conductivity has been examined by various techniques showing that these materials behave as semiconductors. The electrochemical behaviour indicates different oxidation-reduction steps in both cases concomitant with the insertion/deinsertion of lithium in non-reversible processes. X-ray diffraction patterns show that the above process is topotactic in LiCrMnO 4. Magnetic data and neutron diffraction measurements show that no long-range magnetic ordering is present, suggesting a spin-glass transition for M=Cr at low temperature, while for M=Ti the presence of non-magnetic ions in the octahedral sublattice provokes an inherent magnetic frustration.

Molecular design of TiO2 for gigantic red shift via sublattice substitution.

Science.gov (United States)

Shao, Guosheng; Deng, Quanrong; Wan, Lin; Guo, Meilan; Xia, Xiaohong; Gao, Yun

2010-11-01

The effects of 3d transition metal doping in TiO2 phases have been simulated in detail. The results of modelling indicate that Mn has the biggest potential among 3d transition metals, for the reduction of energy gap and the introduction of effective intermediate bands to allow multi-band optical absorption. On the basis of theoretical formulation, we have incorporated considerable amount of Mn in nano-crystalline TiO2 materials. Mn doped samples demonstrate significant red shift in the optical absorption edge, with a secondary absorption edge corresponding to theoretically predicted intermediate bands/states. The gigantic red shift achievable in Mn-doped TiO2 is expected to extend the useful TiO2 functionalities well beyond the UV threshold via the optical absorption of both visible and infrared photon irradiance.

The changes of capacitance-loss and current-voltage characteristics of LaMnO3+δ/SrTiO3:Nb heterojunctions exposed to ambient air

International Nuclear Information System (INIS)

Cui Yimin; Wang Rongming

2010-01-01

Effects of moisture absorption on capacitance-loss and current-voltage characteristics of LaMnO 3+δ /SrTiO 3 :Nb heterojunction had been investigated after the heterojunctions were exposed to ambient air. The moisture-absorption-induced increases in loss tangent and breakdown voltage were observed, whereas no changes were found on capacitance and diffusion voltage. These results were discussed by the decrease of oxygen ions in LaMnO 3+δ and the generation of hydroxide ions at grain boundaries. This work will favor both electronic transport analysis and future device applications.

Thickness dependence of La0.7Sr0.3MnO3/PbZr0.2Ti0.8O3 magnetoelectric interfaces

Science.gov (United States)

Zhou, Jinling; Tra, Vu Thanh; Dong, Shuai; Trappen, Robbyn; Marcus, Matthew A.; Jenkins, Catherine; Frye, Charles; Wolfe, Evan; White, Ryan; Polisetty, Srinivas; Lin, Jiunn-Yuan; LeBeau, James M.; Chu, Ying-Hao; Holcomb, Mikel Barry

2015-10-01

Magnetoelectric materials have great potential to revolutionize electronic devices due to the coupling of their electric and magnetic properties. Thickness varying La0.7Sr0.3MnO3 (LSMO)/PbZr0.2Ti0.8O3 (PZT) heterostructures were built and measured in this article by valence sensitive x-ray absorption spectroscopy. The sizing effects of the heterostructures on the LSMO/PZT magnetoelectric interfaces were investigated through the behavior of Mn valence, a property associated with the LSMO magnetization. We found that Mn valence increases with both LSMO and PZT thickness. Piezoresponse force microscopy revealed a transition from monodomain to polydomain structure along the PZT thickness gradient. The ferroelectric surface charge may change with domain structure and its effects on Mn valence were simulated using a two-orbital double-exchange model. The screening of ferroelectric surface charge increases the electron charges in the interface region, and greatly changes the interfacial Mn valence, which likely plays a leading role in the interfacial magnetoelectric coupling. The LSMO thickness dependence was examined through the combination of two detection modes with drastically different attenuation depths. The different length scales of these techniques' sensitivity to the atomic valence were used to estimate the depth dependence Mn valence. A smaller interfacial Mn valence than the bulk was found by globally fitting the experimental results.

Molecular orbital (SCF-X-α-SW) theory of Fe2+-Mn3+, Fe3+-Mn2+, and Fe3+-Mn3+ charge transfer and magnetic exchange in oxides and silicates

Science.gov (United States)

Sherman, David M.

1990-01-01

Metal-metal charge-transfer and magnetic exchange interactions have important effects on the optical spectra, crystal chemistry, and physics of minerals. Previous molecular orbital calculations have provided insight on the nature of Fe2+-Fe3+ and Fe2+-Ti4+ charge-transfer transitions in oxides and silicates. In this work, spin-unrestricted molecular orbital calculations on (FeMnO10) clusters are used to study the nature of magnetic exchange and electron delocalization (charge transfer) associated with Fe3+-Mn2+, Fe3+-Mn3+, and Fe2+-Mn3+ interactions in oxides and silicates. 

Characterisation of a natural quartz crystal as a reference material for microanalytical determination of Ti, Al, Li, Fe, Mn, Ga and Ge

Science.gov (United States)

Audetat, Andreas; Garbe-Schonberg, Dieter; Kronz, Andreas; Pettke, Thomas; Rusk, Brian G.; Donovan, John J.; Lowers, Heather

2015-01-01

A natural smoky quartz crystal from Shandong province, China, was characterised by laser ablation ICP-MS, electron probe microanalysis (EPMA) and solution ICP-MS to determine the concentration of twenty-four trace and ultra trace elements. Our main focus was on Ti quantification because of the increased use of this element for titanium-in-quartz (TitaniQ) thermobarometry. Pieces of a uniform growth zone of 9 mm thickness within the quartz crystal were analysed in four different LA-ICP-MS laboratories, three EPMA laboratories and one solution-ICP-MS laboratory. The results reveal reproducible concentrations of Ti (57 ± 4 μg g-1), Al (154 ± 15 μg g-1), Li (30 ± 2 μg g-1), Fe (2.2 ± 0.3 μg g-1), Mn (0.34 ± 0.04 μg g-1), Ge (1.7 ± 0.2 μg g-1) and Ga (0.020 ± 0.002 μg g-1) and detectable, but less reproducible, concentrations of Be, B, Na, Cu, Zr, Sn and Pb. Concentrations of K, Ca, Sr, Mo, Ag, Sb, Ba and Au were below the limits of detection of all three techniques. The uncertainties on the average concentration determinations by multiple techniques and laboratories for Ti, Al, Li, Fe, Mn, Ga and Ge are low; hence, this quartz can serve as a reference material or a secondary reference material for microanalytical applications involving the quantification of trace elements in quartz.

First-Principles Study on the Structural Stability and Segregation Behavior of γ-Fe/Cr2N Interface with Alloying Additives M (M = Mn, V, Ti, Mo, and Ni

Directory of Open Access Journals (Sweden)

Hui Huang

2016-07-01

Full Text Available This study investigated the structural stability and electrochemical properties of alloying additives M (M = Mn, V, Ti, Mo, or Ni at the γ-Fe(111/Cr2N(0001 interface by the first-principles method. Results indicated that V and Ti were easily segregated at the γ-Fe(111/Cr2N(0001 interface and enhanced interfacial adhesive strength. By contrast, Ni and Mo were difficult to segregate at the γ-Fe(111/Cr2N(0001 interface. Moreover, the results of the work function demonstrated that alloying additives Mn reduced local electrochemical corrosion behavior of the γ-Fe(111/Cr2N(0001 interface by cutting down Volta potential difference (VPD between clean γ-Fe(111 and Cr2N(0001, while alloying additives V, Ti, Mo, and Ni at the γ-Fe(111/Cr2N(0001 interface magnified VPD between clean γ-Fe(111 and Cr2N(0001, which were low-potential sites that usually serve as local attack initiation points.

Solid solution and amorphous phase in Ti–Nb–Ta–Mn systems synthesized by mechanical alloying

Energy Technology Data Exchange (ETDEWEB)

Aguilar, C., E-mail: claudio.aguilar@usm.cl [Departamento de Ingeniería Metalúrgica y Materiales, Universidad Técnica Federico Santa María, Av. España 1680, Valparaíso (Chile); Guzman, P. [Departamento de Ingeniería Metalúrgica y Materiales, Universidad Técnica Federico Santa María, Av. España 1680, Valparaíso (Chile); Lascano, S. [Departamento de Ingeniería Mecánica, Universidad Técnica Federico Santa María, Av. España 1680, Valparaíso (Chile); Parra, C. [Departamento de Física, Universidad Técnica Federico Santa María, Av. España 1680, Valparaíso (Chile); Bejar, L. [Instituto de Investigaciones Metalúrgicas, Universidad Michoacana de San Nicolás de Hidalgo, Ciudad Universitaria, Morelia C.P. 58000, Michoacán (Mexico); Medina, A. [Facultad de Ingeniería Mecánica, Universidad Michoacana de San Nicolás de Hidalgo, Ciudad Universitaria, C.P. 58000, Michoacán (Mexico); Guzman, D. [Departamento de Metalurgia, Universidad de Atacama, Av. España 485, Copiapó (Chile)

2016-06-15

This work discusses the formation of Ti–30Nb–13Ta–xMn (x: 2, 4 and 6 wt%) solid solution by mechanical alloying using a shaker mill. A solid solution was formed after 15 h of milling and an amorphous phase was formed after 30 h of milling, according to X-ray diffraction results. Disappearance of strongest X-ray diffraction peaks of Nb, Ta and Mn indicated the formation of solid solution, while, X-ray diffraction patterns of powders milled for 30 h showed an amorphous hump with crystalline peaks in the angular range of 35–45° in 2θ. TEM image analysis showed the presence of nanocrystalline intermetallic compounds embedded in an amorphous matrix. Mn{sub 2}Ti, MnTi and NbTi{sub 4} intermetallic compounds were detected and revealed crystallites with size ranging from 3 to 20 nm. The Gibbs free energy for the formation of solid solution and amorphous phase of three ternary systems (Ti–Nb–Ta, Ti–Nb–Mn and Ti–Ta–Mn) was calculated using extended Miedema's model. Experimental and thermodynamic data confirmed that solid solution was first formed in the alloy with 6wt% Mn followed by the formation of an amorphous phase as milling time increases. The presence of Mn promoted the formation of amorphous phase because the atomic radius difference between Mn with Ti, Nb and Ta. - Highlights: • Thermodynamics analysis of extension of solid solution of the Ti–Nb–Ta–Mn system. • Formation of amorphous phase and intermetallic compounds were observed. • Nanocrystalline intermetallic compounds were formed with the sizes between 3 and 20 nm.

Magnetic behavior of La2/3Ca1/3MnO3 / BaTiO3 bilayers

Science.gov (United States)

Ordonez, John E.; Gomez, Maria E.; Lopera, Wilson; Marin, Lorena; Pardo, Jose A.; Morellon, Luis; Algarabel, Pedro; Prieto, Pedro

2013-03-01

We have grown ferroelectric BaTiO3(BTO) and ferromagnetic La2/3Ca1/3MnO3 (LCMO) onto (001) SrTiO3 and Nb:SrTiO3 by pulsed laser deposition (PLD) at pure oxygen atmosphere, and a substrate temperature of 820° C, seeking for a multiferroic behavior in this structure. From x-ray diffraction (XRD) we found lattice parameter aBTO=4.068 Å, and aLCMO=3.804 Å, for each individual layer. In the BTO/LCMO bilayer, (002)-Bragg peak for BTO maintain its position whereas (002) LCMO peak shift to lower Bragg angle indicating a strained LCMO film. Magnetization measurements reveal an increase in the Curie temperature from 170 K to 220 K for the bilayer when LCMO (t = 47 nm) is deposited on BTO (t=52 nm) film, while depositing the BTO (50 nm) above LCMO (48 nm) the Curie temperature remains at values close to that obtained for a LCMO single layer (~175 K), deposited under identical growth parameters This work has been supported by Instituto de Nanociencias de Aragón, Zaragoza, Spain, ``El Patrimonio Autónomo Fondo Nacional de Financiamiento para CT&I FJC'' COLCIENCIAS-CENM Contract RC 275-2011 and Research Project COLCIENCIAS-UNIVALLE.

Fabrication and Raman scattering of a core–shell structure based on Mn doped ZnO and barium titanate

Energy Technology Data Exchange (ETDEWEB)

Sima, M., E-mail: msima@infim.ro [National Institute of Materials Physics, 105 bis Atomistilor Street, PO Box MG 7, 077125 Magurele (Romania); Baibarac, M. [National Institute of Materials Physics, 105 bis Atomistilor Street, PO Box MG 7, 077125 Magurele (Romania); Vasile, E. [University “Politehnica” of Bucharest, Faculty of Applied Chemistry and Material Science, Department of Oxide Materials and Nanomaterials, No. 1-7 Gh. Polizu Street, 011061 Bucharest (Romania); Sima, Ma.; Mihut, L. [National Institute of Materials Physics, 105 bis Atomistilor Street, PO Box MG 7, 077125 Magurele (Romania)

2015-11-15

Graphical abstract: - Highlights: • ZnO/Zn{sub 1−x}Mn{sub x}O/BaTiO{sub 3} nanorod array on FTO substrate. • Oxygen vacancies in the ZnO/Zn{sub 1−x}Mn{sub x}O nanostructure. • The interface between the ZnO/Zn{sub 1−x}Mn{sub x}O core and the BaTiO{sub 3} shell without unwanted phases. - Abstract: A combination of chemical and thermal annealing techniques was used to prepare an array of ZnO/Zn{sub 1−x}Mn{sub x}O/BaTiO{sub 3} nanorods. ZnO nanorod arrays were obtained by hydrothermal–electrochemical processes. The precursors for Zn{sub 1−x}Mn{sub x}O and BaTiO{sub 3}, prepared by sol–gel technique were deposited by spin coating on the surface of ZnO nanorods. Each deposition stage was accompanied by thermal treatment stages. Scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and photoluminescence spectroscopy reveal the presence of a film of Zn{sub 1−x}Mn{sub x}O with wurtzite structure on the surface of ZnO nanorods. Transmission electron microscopy images demonstrate that a layer of BaTiO{sub 3} is deposited on the surface of each ZnO/Zn{sub 1−x}Mn{sub x}O core shell nanorod. BaTiO{sub 3} film onto the ZnO/Zn{sub 1−x}Mn{sub x}O core shell nanorods is also evidenced in Raman scattering by broadening of the Raman band situated in the spectral range 500–750 cm{sup −1}.

Reaction of hydrogen with the Laves phase (C14) TiCr{sub 1.78-x}Mn{sub x} compounds

Energy Technology Data Exchange (ETDEWEB)

Agresti, F. [Universita di Padova, Dipartimento di Ingegneria Meccanica, Settore Materiali and CNISM, via Marzolo 9, 35131 Padova (Italy); Lo Russo, S. [Universita di Padova, Dipartimento di Fisica and CNISM, via Marzolo 8, 35131 Padova (Italy); Maddalena, A.; Principi, G. [Universita di Padova, Dipartimento di Ingegneria Meccanica, Settore Materiali and CNISM, via Marzolo 9, 35131 Padova (Italy); Mazzolai, G. [Universita di Perugia, Dipartimento di Fisica, Via A. Pascoli 5, 06100 Perugia (Italy); Universita Telematica e-Campus, Via Isimbardi 10, Novedrate (Colombia) (Italy); Coluzzi, B.; Biscarini, A. [Universita di Perugia, Dipartimento di Fisica, Via A. Pascoli 5, 06100 Perugia (Italy); Mazzolai, F.M., E-mail: fabio.mazzolai@fisica.unipg.it [Universita di Perugia, Dipartimento di Fisica, Via A. Pascoli 5, 06100 Perugia (Italy); Tuissi, A. [Istituto per l' Energia e le Interfasi, CNR-IENI, C.so Promessi Sposi, 29, Lecco (Italy)

2009-09-15

The lattice constants a and c of the as cast hexagonal (C14) Laves phase TiCr{sub 1.78-x}Mn{sub x} (x = 0, 0.4, 0.6 and 0.8) have been measured by X-ray diffraction at room temperature as a function of the Mn content. It has been found that a decreases with increasing x while c remains almost unchanged. Being this alloy interesting as material for solid state hydrogen storage, pressure-composition isotherms have been traced on desorption mode for the H{sub 2} gas pressure and temperature varying from 10 to 0.01 MPa and from 209 to 307 K, respectively. From the temperature dependence of the plateau pressure the molar quantities {Delta}H-bar{sub H{sub 2}} and {Delta}S-bar{sub H{sub 2}} associated with the hydride decomposition have been determined as a function of the Mn content. With increasing x, both {Delta}H-bar{sub H{sub 2}} and {Delta}S-bar{sub H{sub 2}} progressively decrease, and the desorption pressure initially decreases (for x {<=} 0.4) then slightly increases. At the same time, the pseudo-plateaus become flatter.

Processing and characterization of AlCoFeNiXTi{sub 0,5} (X = Mn, V) high entropy alloys; Processamento e caracterizacao de ligas de alta entropia AlCoFeNixTi{sub 0,5} (X = Mn, V)

Energy Technology Data Exchange (ETDEWEB)

Triveno Rios, C., E-mail: carlos.triveno@ufabc.edu.br [Universidade Federal do ABC (CECS/UFABC), Santo Andre, SP (Brazil). Engenharia de Materiais; Lopes, E.S.N.; Caram, R. [Universidade Estadual de Campinas (FEM/DEMA/UNICAMP), Campinas, SP (Brazil); Kiminami, C.S. [Universidade Federal de Sao Carlos (DEMa/UFSCar), Sao Carlos, SP (Brazil). Departamento de Engenharia de Materiais

2014-07-01

The microstructure of high entropy alloys consists of solid solution phases with FC and BCC simple structures, contrary to classical metallurgy where they form complex structures of intermetallic compounds. Because of this they have several attractive properties for engineering applications. In this work the AlCoFeNiMnTi{sub 0,5} and AlCoFeNiVTi{sub 0,5} alloys were processed by melting arc. Since the main objective was the microstructural and mechanical characterization of ingots as-cast. The alloys were characterized by scanning electron microscopy, X-ray diffraction, microhardness and cold compression test. The results showed that the microstructure consists mainly of dendrites and interdendritic regions consisting of metastable crystalline phases. It was also observed that the AlCoFeNiVTi{sub 0,5} alloy showed better mechanical properties than the AlCoFeNiMnTi{sub 0,5} alloy. This may be associated with differences in the parameters of formation of simple solid solution phases between the two alloys. (author)

Epitaxial single-crystal thin films of MnxTi1-xO2-δ grown on (rutile)TiO2 substrates with pulsed laser deposition: Experiment and theory

Energy Technology Data Exchange (ETDEWEB)

Ilton, Eugene S.; Droubay, Timothy C.; Chaka, Anne M.; Kovarik, Libor; Varga, Tamas; Arey, Bruce W.; Kerisit, Sebastien N.

2015-02-01

Epitaxial rutile-structured single-crystal MnxTi1-xO2-δ films were synthesized on rutile- (110) and -(001) substrates using pulsed laser deposition. The films were characterized by reflection high-energy electron diffraction (RHEED), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and aberration-corrected transmission electron microscopy (ACTEM). Under the present conditions, 400oC and PO2 = 20 mTorr, single crystal epitaxial thin films were grown for x = 0.13, where x is the nominal average mole fraction of Mn. In fact, arbitrarily thick films could be grown with near invariant Mn/Ti concentration profiles from the substrate/film interface to the film surface. In contrast, at x = 0.25, Mn became enriched towards the surface and a secondary nano-scale phase formed which appeared to maintain the basic rutile structure but with enhanced z-contrast in the tunnels, or tetrahedral interstitial sites. Ab initio thermodynamic calculations provided quantitative estimates for the destabilizing effect of expanding the β-MnO2 lattice parameters to those of TiO2-rutile, the stabilizing effect of diluting Mn with increasing Ti concentration, and competing reaction pathways.

Effect of microalloying elements (Nb, V and Ti) on the hot flow behavior of high-Mn austenitic twinning induced plasticity (TWIP) steel

International Nuclear Information System (INIS)

Reyes-Calderón, F.; Mejía, I.; Boulaajaj, A.; Cabrera, J.M.

2013-01-01

This research work studies the effect of microalloying elements such as Nb, V and Ti on the hot flow behavior of high-Mn austenitic TWIP steel. For this purpose, isothermal uniaxial hot compression tests were carried out at three temperatures (900, 1000 and 1100 °C) and four constant strain rates (10 −1 , 10 −2 , 10 −3 and 10 −4 s −1 ). Experimental results revealed that hot flow curves of microalloyed TWIP steels show single peak curves for all test conditions. Results are discussed in terms of the peak stress (σ p ) and peak strain (ε p ) and its dependence on the strain rate (ε) and temperature. The addition of microalloying elements such as Nb, V and Ti in TWIP steels generates a slight increase in the σ p value, and Ti microalloyed TWIP steel exhibits the highest σ p value. Hot deformed microstructures were analyzed by the Electron Back-Scattering Diffraction Technique (EBSD). The most important results of the austenitic recrystallized grain refinement were obtained for V and Ti microalloyed TWIP steels.

A novel bilayered Sr{sub 0.6}La{sub 0.4}TiO{sub 3}/La{sub 0.8}Sr{sub 0.2}MnO{sub 3} interconnector for anode-supported tubular solid oxide fuel cell via slurry-brushing and co-sintering process

Energy Technology Data Exchange (ETDEWEB)

Xu, Yanjie; Wang, Shaorong; Liu, Renzhu; Wen, Tinglian; Wen, Zhaoyin [CAS Key Laboratory of Materials for Energy Conversion, Shanghai Institute of Ceramics, Chinese Academy of Sciences (SICCAS), 1295 Dingxi Road, Shanghai 200050 (China)

2011-02-01

Considering that conventional lanthanum chromate (LaCrO{sub 3}) interconnector is hard to be co-sintered with green anode, we have fabricated a novel bilayered interconnector which consists of La-doped SrTiO{sub 3} (Sr{sub 0.6}La{sub 0.4}TiO{sub 3}) and Sr-doped lanthanum manganite (La{sub 0.8}Sr{sub 0.2}MnO{sub 3}). Sr{sub 0.6}La{sub 0.4}TiO{sub 3} is conductive and stable in reducing atmosphere, locating on the anode side; while La{sub 0.8}Sr{sub 0.2}MnO{sub 3} is on the cathode side. A slurry-brushing and co-sintering method is applied: the Sr{sub 0.6}La{sub 0.4}TiO{sub 3} and La{sub 0.8}Sr{sub 0.2}MnO{sub 3} slurries are successively brushed onto green anode specimen, followed by co-firing course to form a dense bilayered Sr{sub 0.6}La{sub 0.4}TiO{sub 3}/La{sub 0.8}Sr{sub 0.2}MnO{sub 3} interconnector. For operating with humidified hydrogen and oxygen at 900 C, the ohmic resistances between anode and cathode/interconnector are 0.33 {omega} cm{sup 2} and 0.186 {omega} cm{sup 2}, respectively. The maximum power density is 290 mW cm{sup -2} for a cell with interconnector, and 420 mW cm{sup -2} for a cell without it, which demonstrates that nearly 70% of the power output can be achieved using this bilayered Sr{sub 0.6}La{sub 0.4}TiO{sub 3}/La{sub 0.8}Sr{sub 0.2}MnO{sub 3} interconnector. (author)

Mechanosynthesis of nanocrystalline CaTi1-xMnxO3-δ

Directory of Open Access Journals (Sweden)

Figueiredo, F. M.

2008-08-01

Full Text Available The mechanosynthesis of nanocrystalline CaTi1-xMnxO3-δ is reported for the first time. Powdered CaO, TiO2 anatase and Mn2O3 (Aldrich were weighed in the appropriate stoichiometric quantities in order to obtain CaTi1-xMnxO3-δ (x=0.05, 0.10, 0.15, 0.20, 0.30, 0.50 and 0.80 and dry milled in a planetary high-energy ball mill, using zirconia containers and balls, with a 10:1 ball/mass ratio. The planetary rotation was kept constant at 650 rpm and the container at 1300 rpm, in the opposite direction. Powder XRD patterns revealed a perovskite forming from the early milling stages and a completed reaction after 180 min, with no apparent crystalline or amorphous intermediates, indicating significant Mn solubility in CaTiO3. Patterns show a decrease in lattice volume upon Mn substitution, as expected from the lower Mn3+ or Mn4+ ionic radii when compared to Ti4+. The average crystallite size is in the range 5-30 nm, as determined from Williamson-Hall plots and confirmed by high resolution transmission electron microscopy.La mecanosíntesis de CaTi1-xMnxO3-δ nanocristalino es presentada por primera vez. Polvos reactivos de CaO, TiO2 anatasa y Mn2O3 (Aldrich fueron pesados en las cantidades estequiométricas adecuadas para obtener CaTi1-xMnxO3-δ (x=0.05, 0.10, 0.15, 0.20, 0.30, 0.50 y 0.80 por molienda en seco en un molino planetario de alta energía utilizando contenedores y bolas de circona, en una relación masa de bolas : masa de polvo de 10:1. La rotación del planetario se mantuvo constante a 650 revoluciones por minuto (rpm y la del contenedor a 1300 rpm, en el sentido inverso. La formación de una fase con estructura de perovskita fue identificada a través del análisis de los polvos por difracción de rayos X, siendo esta fase claramente mayoritaria en los polvo molidos durante 180 min y sin observarse la formación de compuestos intermediarios. Los patrones de difracción de rayos X también indicaron una disminución de los parámetro de red

Structure and magnetic properties of La2/3Sr1/3MnO3/CaMnO3 multilayers

International Nuclear Information System (INIS)

Granada, Mara; Sirena, Martin; Steren, Laura B.; Leyva, Gabriela

2004-01-01

Structural and magnetic properties of manganite-based multilayers, La 2/3 Sr 1/3 MnO 3 /CaMnO 3 , composed of ferromagnetic metals and antiferromagnetic insulator barriers are investigated in this work. Compounds of similar lattice parameters were used to build the samples, so we expect an excellent stacking of the different layers along the structure. To get a first insight of this system, the crystalline structure of a series of samples, grown on (1 0 0) SrTiO 3 and (1 0 0) MgO single-crystalline substrates, has been studied. X-ray diffraction patterns show that the structure is strongly textured in the (1 0 0) direction when grown on SrTiO 3 , regardless the composition of the bottom layer. A different result is found on the same system grown on MgO: when the buffer layer is CaMnO 3 , the structure grows in the (1 1 0) orientation while it grows in the (1 0 0) direction when the bottom layer is La 2/3 Sr 1/3 MnO 3 . Magnetic coupling of the ferromagnetic layers across the antiferromagnetic spacer has been studied with magnetization measurements

L1{sub 0} stacked binaries as candidates for hard-magnets. FePt, MnAl and MnGa

Energy Technology Data Exchange (ETDEWEB)

Matsushita, Yu-ichiro [Max-Planck Institut fuer Microstrukture Physics, Halle (Germany); Department of Applied Physics, The University of Tokyo (Japan); Madjarova, Galia [Max-Planck Institut fuer Microstrukture Physics, Halle (Germany); Department of Physical Chemistry, Faculty of Chemistry and Pharmacy, Sofia University (Bulgaria); Flores-Livas, Jose A. [Department of Physics, Universitaet Basel (Switzerland); Dewhurst, J.K.; Gross, E.K.U. [Max-Planck Institut fuer Microstrukture Physics, Halle (Germany); Felser, C. [Max Planck Institute for Chemical Physics of Solids, Dresden (Germany); Sharma, S. [Max-Planck Institut fuer Microstrukture Physics, Halle (Germany); Department of Physics, Indian Institute of Technology, Roorkee, Uttarkhand (India)

2017-08-15

We present a novel approach for designing new hard magnets by forming stacks of existing binary magnets to enhance the magneto crystalline anisotropy. This is followed by an attempt at reducing the amount of expensive metal in these stacks by replacing it with cheaper metal with similar ionic radius. This strategy is explored using examples of FePt, MnAl and MnGa. In this study a few promising materials are suggested as good candidates for hard magnets: stacked binary FePt{sub 2}MnGa{sub 2} in structure where each magnetic layer is separated by two non-magnetic layers, FePtMnGa and FePtMnAl in hexagonally distorted Heusler structures and FePt{sub 0.5}Ti{sub 0.5}MnAl. (copyright 2017 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Displacement-type ferroelectric transition with magnetic Mn ions in perovskite Sr1-xBaxMnO3

Science.gov (United States)

Sakai, Hideaki; Fujioka, Jun; Fukuda, Tatsuo; Okuyama, Daisuke; Hashizume, Daisuke; Kagawa, Fumitaka; Nakao, Hironori; Murakami, Youich; Arima, Takahisa; Baron, Alfred Q. R.; Taguchi, Yasujiro; Tokura, Yoshinori

2012-02-01

Almost all the proper ferroelectrics with a perovskite structure discovered so far have no d-electrons in the off-center transition metal site, as exemplified by BaTiO3 and Pb(Zr,Ti)O3. This empirical d^0 rule is incompatible with the emergence of magnetism and has significantly restricted the variety of multiferroic materials. In this work, we have discovered a displacement-type ferroelectric transition originating from off-center Mn^4+ ions in antiferromagnetic Mott insulators Sr1-xBaxMnO3. As Ba concentration increases, the perovskite lattice shows the typical soft mode dynamics, and the ferroelectricity shows up for x .45. In addition to the large polarization and high transition temperature comparable to BaTiO3, we demonstrate that the magnetic order suppresses the ferroelectric lattice dilation by ˜70% and increases the soft-phonon energy by ˜50%, indicating gigantic magnetoelectric effects [1]. This work was supported by the FIRST program on ``Quantum Science on Strong Correlation''. [4pt] [1] H. Sakai et al., Phys. Rev. Lett. 107, 137601 (2011).

Analysis of multiferroic properties in BiMnO{sub 3} thin films

Energy Technology Data Exchange (ETDEWEB)

Grizalez, M [Universidad de la Amazonia, Florencia (Colombia); Mendoza, G A [Department of Physics, Universidad Nacional de Colombia, Bogota (Colombia); Prieto, P, E-mail: pprieto@calima.univalle.edu.c [Center of Excellence on Novel Materials - CENM (Colombia)

2009-05-01

Textured BiMnO{sub 3} [111] thin films on SrTiO{sub 3} (100) and Pt/TiO{sub 2}/SiO{sub 2} substrates were grown via r.f. magnetron sputtering (13.56 MHz). The XRD spectra confirmed a monoclinic structure and high-quality textured films for the BiMnO{sub 3} films. The films grown on SrTiO{sub 3} (100) showed higher crystalline quality than those developed on Pt/TiO{sub 2}/SiO{sub 2}. Through optimized oxygen pressure of 5x10{sup -2} mbar during the r.f. sputtering deposition, the crystalline orientation of the BiMnO{sub 3} film was improved with respect to the previously reported value of 2x10{sup -1} mbar. The values of spontaneous polarization (P{sub s}), remnant polarization (P{sub r}), and coercive field (F{sub c}) from ferroelectric hysteresis loops (P-E) at different temperatures were also obtained. Samples with higher crystalline order revealed better dielectric properties (high P{sub s} and P{sub r} values and a low F{sub c}). For films on both types of substrates, the ferroelectric behavior was found to persist up to 400K. Measurements at higher temperatures were difficult to obtain given the increased conductivity of the films. Magnetic hysteresis loops from 5K to 120K were obtained for BiMnO{sub 3} films grown on SrTiO{sub 3} and Pt/TiO{sub 2}/SiO{sub 2} substrates. The results suggested that the coexistence of the magnetic and electric phases persists up to 120K.

The Development of the Low-Cost Titanium Alloy Containing Cr and Mn Alloying Elements

Science.gov (United States)

Zhu, Kailiang; Gui, Na; Jiang, Tao; Zhu, Ming; Lu, Xionggang; Zhang, Jieyu; Li, Chonghe

2014-04-01

The α + β-type Ti-4.5Al-6.9Cr-2.3Mn alloy has been theoretically designed on the basis of assessment of the Ti-Al-Cr-Mn thermodynamic system and the relationship between the molybdenum equivalent and mechanical properties of titanium alloys. The alloy is successfully prepared by the split water-cooled copper crucible, and its microstructures and mechanical properties at room temperature are investigated using the OM, SEM, and the universal testing machine. The results show that the Ti-4.5Al-6.9Cr-2.3Mn alloy is an α + β-type alloy which is consistent with the expectation, and its fracture strength, yield strength, and elongation reach 1191.3, 928.4 MPa, and 10.7 pct, respectively. Although there is no strong segregation of alloying elements under the condition of as-cast, the segregation of Cr and Mn is obvious at the grain boundary after thermomechanical treatment.

Direct chemical synthesis of MnO2 nanowhiskers on MXene surfaces for supercapacitor applications

KAUST Repository

Baby, Rakhi Raghavan

2016-07-05

Transition metal carbides (MXenes) are an emerging class of two dimensional (2D) materials with promising electrochemical energy storage performance. Herein, for the first time, by direct chemical synthesis, nanocrystalline ε-MnO2 whiskers were formed on MXene nanosheet surfaces (ε-MnO2/Ti2CTx and ε-MnO2/Ti3C2Tx) to make nanocomposite electrodes for aqueous pseudocapacitors. The ε-MnO2 nanowhiskers increase the surface area of the composite electrode and enhance the specific capacitance by nearly three orders of magnitude compared to pure MXene based symmetric supercapacitors. Combined with enhanced pseudocapacitance, the fabricated ε-MnO2/MXene supercapacitors exhibited excellent cycling stability with ~88% of the initial specific capacitance retained after 10000 cycles which is much higher than pure ε-MnO2 based supercapacitors (~74%). The proposed electrode structure capitalizes on the high specific capacitance of MnO2 and the ability of MXenes to improve conductivity and cycling stability.

Inclusion Characteristics and Acicular Ferrite Nucleation in Ti-Containing Weld Metals of X80 Pipeline Steel

Science.gov (United States)

Wang, Bingxin; Liu, Xianghua; Wang, Guodong

2018-06-01

X80 steel weld metals with Ti contents of 0.003 to 0.13 pct were prepared by the single-pass submerged-arc welding process. The effects of Ti content in weld metals on the constituent phases of inclusions and chemical compositions of the constituent phases, as well as the potency of acicular ferrite (AF) nucleation on the inclusions were investigated. Moreover, the crystallographic orientation relationship between the AF and inclusion was examined. The results show that with an increase in Ti content, the primary constituent phases of the inclusions change from the (Mn-Al-Si-O) compound to a mixture of spinel and pseudobrookite solid solutions, and eventually to pseudobrookite. The spinel solid solution is characterized by the MnTi2O4 constituent. Compared to pseudobrookite, spinel has a lower Ti concentration, but a significantly higher Mn content. In the case of the presence of a considerable amount of spinel, the Mn element is enriched strongly in the inclusions, resulting in the development of a Mn-depleted zone (MDZ) in the matrix around the inclusions, which enhances the driving force for AF formation. AF shows the Baker-Nutting orientation relationship with MnTi2O4. The formation of MDZ and the presence of the Baker-Nutting orientation relationship promote the ability of inclusions to nucleate the intragranular AF.

Misfit dislocations of anisotropic magnetoresistant Nd0.45Sr0.55MnO3 thin films grown on SrTiO3 (1 1 0) substrates

International Nuclear Information System (INIS)

Tang, Y.L.; Zhu, Y.L.; Meng, H.; Zhang, Y.Q.; Ma, X.L.

2012-01-01

Nd 0.45 Sr 0.55 MnO 3 is an A-type antiferromagnetic manganite showing obvious angular-dependent magnetoresistance, which can be tuned by misfit strain. The misfit strain relaxation of Nd 0.45 Sr 0.55 MnO 3 thin films is of both fundamental and technical importance. In this paper, microstructures of epitaxial Nd 0.45 Sr 0.55 MnO 3 thin films grown on SrTiO 3 (1 1 0) substrates by pulsed laser deposition were investigated by means of (scanning) transmission electron microscopy. The Nd 0.45 Sr 0.55 MnO 3 thin films exhibit a two-layered structure: a continuous perovskite layer epitaxial grown on the substrate followed by epitaxially grown columnar nanostructures. An approximately periodic array of misfit dislocations is found along the interface with line directions of both 〈1 1 1〉 and [0 0 1]. High-resolution (scanning) transmission electron microscopy reveals that all the misfit dislocations possess a〈1 1 0〉-type Burgers vectors. A formation mechanism based on gliding or climbing of the dislocations is proposed to elucidate this novel misfit dislocation configuration. These misfit dislocations have complex effects on the strain relaxation and microstructure of the films, and thus their influence needs further consideration for heteroepitaxial perovskite thin film systems, especially for films grown on substrates with low-symmetry surfaces such as SrTiO 3 (1 1 0) and (1 1 1), which are attracting attention for their potentially new functions.

Dielectric relaxation in epitaxial films of paraelectric-magnetic SrTiO.sub.3./sub.-SrMnO.sub.3./sub. solid solution

Czech Academy of Sciences Publication Activity Database

Savinov, Maxim; Bovtun, Viktor; Tereshina-Chitrova, Evgenia; Stupakov, Alexandr; Dejneka, Alexandr; Tyunina, Marina

2018-01-01

Roč. 112, č. 5 (2018), s. 1-4, č. článku 052901. ISSN 0003-6951 R&D Projects: GA ČR GA15-15123S Institutional support: RVO:68378271 Keywords : dielectric relaxation * epitaxial films * paraelectric-magnetic * SrTiO 3 -SrMnO 3 solid solution Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics , supercond.) Impact factor: 3.411, year: 2016

Influence of Ti on the Hot Ductility of High-manganese Austenitic Steels

Science.gov (United States)

Liu, Hongbo; Liu, Jianhua; Wu, Bowei; Su, Xiaofeng; Li, Shiqi; Ding, Hao

2017-07-01

The influence of Ti addition ( 0.10 wt%) on hot ductility of as-cast high-manganese austenitic steels has been examined over the temperature range 650-1,250 °C under a constant strain rate of 10-3 s-1 using Gleeble3500 thermal simulation testing machine. The fracture surfaces and particles precipitated at different tensile temperatures were characterized by means of scanning electron microscope and X-ray energy dispersive spectrometry (SEM-EDS). Hot ductility as a function of reduction curves shows that adding 0.10 wt% Ti made the ductility worse in the almost entire range of testing temperatures. The phases' equilibrium diagrams of precipitates in Ti-bearing high-Mn austenitic steel were calculated by the Thermo-Calc software. The calculation result shows that 0.1 wt% Ti addition would cause Ti(C,N) precipitated at 1,499 °C, which is higher than the liquidus temperature of high-Mn austenitic steel. It indicated that Ti(C,N) particles start forming in the liquid high-Mn austenitic steel. The SEM-EDS results show that Ti(C,N) and TiC particles could be found along the austenite grain boundaries or at triple junction, and they would accelerate the extension of the cracks along the grain boundaries.

Above room-temperature ferromagnetism in La1-xCaxMnO3 epitaxial thin films on SrTiO3(001) substrates

Science.gov (United States)

Kou, Yunfang; Wang, Hui; Miao, Tian; Wang, Yanmei; Xie, Lin; Wang, Shasha; Liu, Hao; Lin, Hanxuan; Zhu, Yinyan; Wang, Wenbin; Du, Haifeng; Pan, Xiaoqing; Wu, Ruqian; Yin, Lifeng; Shen, Jian

The colossal magnetoresistive (CMR) manganites are popular materials for spintronics applications due to their high spin polarization. Only a couple of manganites like La1-xSrxMnO3 have a Curie temperature (Tc) that is higher than room temperature. Finding methods to raise the Tc of manganites over room temperature is useful but challenging. In this work, we use the most intensively studied La1-xCaxMnO3 (LCMO) as the prototype system to demonstrate that Tc can be greatly enhanced by carefully tuning the electronic structure using doping and strain. Specifically, we grow LCMO films on SrTiO3 (001) substrates using pulsed laser deposition. Magnetic and transport measurements indicate a great enhancement of Tc over room temperature at x =0.2 doping. Theoretical calculations indicate that the combined effects from doping and strain give rise to a new electronic structure favoring ferromagnetism in LCMO system. Furthermore, using the La0.8Ca0.2MnO3 as ferromagnetic electrodes, we achieve finite tunneling magnetoresistance (TMR) above room temperature.

Growth and giant coercive field of spinel-structured Co3- x Mn x O4 thin films

Science.gov (United States)

Kwak, Yongsu; Song, Jonghyun; Koo, Taeyeong

2016-08-01

We grew epitaxial thin films of CoMn2O4 and Co2MnO4 on Nb-doped SrTiO3(011) and SrTiO3(001) single crystal substrates using pulsed laser deposition. The magnetic Curie temperature ( T c ) of the Co2MnO4 thin films was ~176 K, which is higher than that of the bulk whereas CoMn2O4 thin films exhibited a value of T c (~151 K) lower than that of the bulk. For the Co2MnO4 thin films, the M - H loop showed a coercive field of ~0.7 T at 10 K, similar to the value for the bulk. However, the M -H loop of the CoMn2O4(0 ll) thin film grown on a Nb-doped SrTiO3(011) substrate exhibited a coercive field of ~4.5 T at 30 K, which is significantly higher than those of the Co2MnO4 thin film and bulk. This giant coercive field, only observed for the CoMn2O4(0 ll) thin film, can be attributed to the shape anisotropy and strong spin-orbit coupling.

Ferroelectricity-induced resistive switching in Pb(Zr0.52Ti0.48)O3/Pr0.7Ca0.3MnO3/Nb-doped SrTiO3 epitaxial heterostructure

Science.gov (United States)

Md. Sadaf, Sharif; Mostafa Bourim, El; Liu, Xinjun; Hasan Choudhury, Sakeb; Kim, Dong-Wook; Hwang, Hyunsang

2012-03-01

We investigated the effect of a ferroelectric Pb(Zr0.52Ti0.48)O3 (PZT) thin film on the generation of resistive switching in a stacked Pr0.7Ca0.3MnO3 (PCMO)/Nb-doped SrTiO3 (Nb:STO) heterostructure forming a p-n junction. To promote the ferroelectric effect, the thin PZT active layer was deposited on an epitaxially grown p-type PCMO film on a lattice-matched n-type Nb:STO single crystal. It was concluded that the observed resistive switching behavior in the all-perovskite Pt/PZT/PCMO/Nb:STO heterostructure was related to the modulation of PCMO/Nb:STO p-n junction's depletion width, which was caused either by the PZT ferroelectric polarization field effect, the electrochemical drift of oxygen ions under an electric field, or both simultaneously.

Piezoelectric properties and temperature stability of Mn-doped Pb(Mg1/3Nb2/3)-PbZrO3-PbTiO3 textured ceramics

Science.gov (United States)

Yan, Yongke; Cho, Kyung-Hoon; Priya, Shashank

2012-03-01

In this letter, we report the electromechanical properties of textured 0.4Pb(Mg1/3Nb2/3)O3-0.25PbZrO3-0.35PbTiO3 (PMN-PZT) composition which has relatively high rhombohedral to tetragonal (R-T) transition temperature (TR-T of 160 °C) and Curie temperature (TC of 234 °C) and explore the effect of Mn-doping on this composition. It was found that MnO2-doped textured PMN-PZT ceramics with 5 vol. % BaTiO3 template (T-5BT) exhibited inferior temperature stability. The coupling factor (k31) of T-5BT ceramic started to degrade from 75 °C while the random counterpart showed a very stable tendency up to 180 °C. This degradation was associated with the "interface region" formed in the vicinity of BT template. MnO2 doped PMN-PZT ceramics textured with 3 vol. % BT and subsequently poled at 140 °C (T-3BT140) exhibited very stable and high k31 (>0.53) in a wide temperature range from room temperature to 130 °C through reduction in the interface region volume. Further, the T-3BT140 ceramic exhibited excellent hard and soft combinatory piezoelectric properties of d33 = 720 pC/N, k31 = 0.53, Qm = 403, tan δ = 0.3% which are very promising for high power and magnetoelectric applications.

Combined effects Na and SO{sub 2} in flue gas on Mn-Ce/TiO{sub 2} catalyst for low temperature selective catalytic reduction of NO by NH{sub 3} simulated by Na{sub 2}SO{sub 4} doping

Energy Technology Data Exchange (ETDEWEB)

Zhou, Aiyi [Department of Environmental Science and Engineering, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing 210023 (China); Yu, Danqing [School of Chemical Engineering and Technology, Wuhan University of Science and Technology, Wuhan 430081 (China); Yang, Liu [Department of Environmental Science and Engineering, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing 210023 (China); Sheng, Zhongyi, E-mail: 09377@njnu.edu.cn [Department of Environmental Science and Engineering, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing 210023 (China)

2016-08-15

Highlights: • Sodium sulfate (Na{sub 2}SO{sub 4}) was deposited on Mn-Ce/TiO{sub 2} catalyst to simulate the co-existing of sodium and SO{sub 2} in the flue gas. • Na{sub 2}SO{sub 4} had strong and fluctuant influence on Mn-Ce/TiO{sub 2} catalyst’s performance in SCR of NOx with NH{sub 3}, due to the combined effect of the deactivation of sodium salts and the enhanced performance of ceria with surface sulfation. • The changes of the surface chemical species and acid sites on the Na{sub 2}SO{sub 4} deposited catalysts could be considered as the main reasons for the fluctuation changes with the catalytic activity. - Abstract: A series of Mn-Ce/TiO{sub 2} catalysts were synthesized through an impregnation method and used for low temperature selective catalytic reduction (SCR) of NOx with ammonia (NH{sub 3}). Na{sub 2}SO{sub 4} was added into the catalyst to simulate the combined effects of alkali metal and SO{sub 2} in the flue gas. Experimental results showed that Na{sub 2}SO{sub 4} had strong and fluctuant influence on the activity of Mn-Ce/TiO{sub 2}, because the effect of Na{sub 2}SO{sub 4} included pore occlusion and sulfation effect simultaneously. When Na{sub 2}SO{sub 4} loading content increased from 0 to 1 wt.%, the SCR activities of Na{sub 2}SO{sub 4}-doped catalysts decreased greatly. With further increasing amount of Na{sub 2}SO{sub 4}, however, the catalytic activity increased gradually. XRD results showed that Na{sub 2}SO{sub 4} doping could induce the crystallization of MnOx phases, which were also confirmed by TEM and SEM results. BET results showed that the surface areas decreased and a new bimodal mesoporous structure formed gradually with the increasing amount of Na{sub 2}SO{sub 4}. XPS results indicated that part of Ce{sup 4+} and Mn{sup 3+} were transferred to Ce{sup 3+} and Mn{sup 4+} due to the sulfation after Na{sub 2}SO{sub 4} deposition on the surface of the catalysts. When the doped amounts of Na{sub 2}SO{sub 4} increased, NH{sub 3

Electron paramagnetic resonance studies of manganese centers in SrTiO.sub.3./sub.: Non-Kramers Mn.sup.3+./sup. ions and spin-spin coupled Mn.sup.4+./sup. dimers

Czech Academy of Sciences Publication Activity Database

Azamat, Dmitry; Dejneka, Alexandr; Lančok, Ján; Trepakov, Vladimír; Jastrabík, Lubomír; Badalyan, A. G.

2012-01-01

Roč. 111, č. 10 (2012), "104119-1"-"104119-6" ISSN 0021-8979. [International Symposium on Integrated Functionalities (ISIF) /22./. San Juan, Puerto Rico , 13.06.2010-16.06.2010] R&D Projects: GA TA ČR TA01010517; GA MŠk(CZ) LM2011029; GA ČR GAP108/12/1941 Grant - others:SAFMAT(CZ) CZ.2.16/3.1.00/22132 Institutional research plan: CEZ:AV0Z10100522 Keywords : electron paramagnetic resonance * X- and Q-band * SrTiO 3 doped with Mn Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.210, year: 2012

Concurrent ionic migration and electronic effects at the memristive TiO x /La1/3Ca2/3MnO3-x interface

Science.gov (United States)

Román Acevedo, W.; Ferreyra, C.; Sánchez, M. J.; Acha, C.; Gay, R.; Rubi, D.

2018-03-01

The development of reliable redox-based resistive random-access memory devices requires understanding and disentangling concurrent effects present at memristive interfaces. We report on the fabrication and electrical characterization of TiO x /La1/3Ca2/3MnO3-x microstructured interfaces and on the modeling of their memristive behavior. We show that a careful tuning of the applied external electrical stimuli allows controlling the redox process between both layers, obtaining multilevel non-volatile resistance states. We simulate the oxygen vacancies dynamics at the interface between both oxides, and successfully reproduce the experimental electrical behavior after the inclusion of an electronic effect, related to the presence of an n-p diode at the interface. The formation of the diode is due to the n- and p-character of TiO x and La1/3Ca2/3MnO3-x , respectively. Our analysis indicates that oxygen vacancies migration between both layers is triggered after the diode is polarized either in forward mode or in reverse mode above breakdown. Electrical measurements at different temperatures suggest that the diode can be characterized as Zener-type. The advantages of our junctions for their implementation in RRAM devices are finally discussed.

Chromium-free conversion coatings based on inorganic salts (Zr/Ti/Mn/Mo) for aluminum alloys used in aircraft applications

Energy Technology Data Exchange (ETDEWEB)

Santa Coloma, P., E-mail: patricia.santacoloma@tecnalia.com [TECNALIA Research & Innovation, Parque Tecnológico de San Sebastián, Mikeletegi Pasealekua 2, E-20009 Donostia-San Sebastián, Gipuzkoa (Spain); Izagirre, U.; Belaustegi, Y.; Jorcin, J.B.; Cano, F.J. [TECNALIA Research & Innovation, Parque Tecnológico de San Sebastián, Mikeletegi Pasealekua 2, E-20009 Donostia-San Sebastián, Gipuzkoa (Spain); Lapeña, N. [Boeing Research & Technology Europe, S.L.U., Avenida Sur del Aeropuerto de Barajas 38, Building 4 – 3rd Floor, E-28042 Madrid (Spain)

2015-08-01

Highlights: • Chromium-free conversion coatings for corrosion protection of aluminum alloys. • Salt spray and potentiodynamic sweep tests to study the corrosion behavior. • Local deposits on Cu-rich intermetallic particles enhanced corrosion resistance. • Surface characterization to relate bath's composition and corrosion resistance. • Best corrosion protection with conversion baths without titanium salts. - Abstract: Novel chromium-free conversion coatings based on Zr/Ti/Mn/Mo compounds were developed at a pilot scale to improve the corrosion resistance of the AA2024-T3 and AA7075-T6 aluminum alloys for aircraft applications. The influence of the presence of Zr and Ti in the Zr/Ti/Mn/Mo conversion bath's formulation on the corrosion resistance of the coated alloys was investigated. The corrosion resistance provided by the conversion coatings was evaluated by salt spray exposure and potentiodynamic sweeps. Optical and scanning electron microscopy coupled with energy dispersive spectroscopy (SEM/EDS) and atomic force microscopy (AFM) operating in the Kelvin Probe mode (SKPFM) were used to provide microstructural information of the coated samples that achieved the best results in the corrosion tests. The salt spray test evidenced the higher corrosion resistance of the coated samples compared to the bare surfaces for both alloys. The potentiodynamic tests showed that the corrosion current density decreased for coated AA7075-T6 and AA2024-T3 alloys, which indicated an obvious improvement of the corrosion resistance with all the processes for both alloys. Although the corrosion resistance of the coated samples appeared to be higher for the alloy AA7075-T6 than for the alloy AA2024-T3, both alloys achieved the best corrosion protection with the coatings deposited from conversion bath formulations containing no titanium salts. The microscopy analysis on the coated AA7075-T6 samples revealed that a local deposition of Zr compounds and, possibly, an

Chromium-free conversion coatings based on inorganic salts (Zr/Ti/Mn/Mo) for aluminum alloys used in aircraft applications

International Nuclear Information System (INIS)

Santa Coloma, P.; Izagirre, U.; Belaustegi, Y.; Jorcin, J.B.; Cano, F.J.; Lapeña, N.

2015-01-01

Highlights: • Chromium-free conversion coatings for corrosion protection of aluminum alloys. • Salt spray and potentiodynamic sweep tests to study the corrosion behavior. • Local deposits on Cu-rich intermetallic particles enhanced corrosion resistance. • Surface characterization to relate bath's composition and corrosion resistance. • Best corrosion protection with conversion baths without titanium salts. - Abstract: Novel chromium-free conversion coatings based on Zr/Ti/Mn/Mo compounds were developed at a pilot scale to improve the corrosion resistance of the AA2024-T3 and AA7075-T6 aluminum alloys for aircraft applications. The influence of the presence of Zr and Ti in the Zr/Ti/Mn/Mo conversion bath's formulation on the corrosion resistance of the coated alloys was investigated. The corrosion resistance provided by the conversion coatings was evaluated by salt spray exposure and potentiodynamic sweeps. Optical and scanning electron microscopy coupled with energy dispersive spectroscopy (SEM/EDS) and atomic force microscopy (AFM) operating in the Kelvin Probe mode (SKPFM) were used to provide microstructural information of the coated samples that achieved the best results in the corrosion tests. The salt spray test evidenced the higher corrosion resistance of the coated samples compared to the bare surfaces for both alloys. The potentiodynamic tests showed that the corrosion current density decreased for coated AA7075-T6 and AA2024-T3 alloys, which indicated an obvious improvement of the corrosion resistance with all the processes for both alloys. Although the corrosion resistance of the coated samples appeared to be higher for the alloy AA7075-T6 than for the alloy AA2024-T3, both alloys achieved the best corrosion protection with the coatings deposited from conversion bath formulations containing no titanium salts. The microscopy analysis on the coated AA7075-T6 samples revealed that a local deposition of Zr compounds and, possibly, an

High temperature corrosion behaviour of Ti-46.6Al-1.4Mn-2Mo in environments of low oxygen and high sulphur potentials at 750 and 900 C

International Nuclear Information System (INIS)

Du, H.L.; Datta, P.K.; Hwang, S.K.

1997-01-01

In this paper, the oxidation and sulphidation behaviour of a TiAl-based intermetallic, Ti-46.6Al-1.4Mn-2Mo (at%) with duplex and laminar microstructures, was investigated in environments of H 2 /H 2 S/H 2 O at 750 and 900 C. The corrosion kinetics of the intermetallic were determined by means of discontinuous gravimetry and the as-received and exposed samples were characterised using SEM, EDX and XRD. The weight gain/time data in the oxygen and sulphur containing environment used indicated parabolic kinetics with Kp∝10 -12 g 2 /cm 4 /s at 750 C and cubic kinetics at 900 C. The increase in exposure temperature did not significantly change the corrosion behaviour of the materials. The material showed the development of a multilayered scale consisting of an outermost TiO 2 layer beneath which an Al 2 O 3 layer existed: the formation of MnS and Al 2 S 3 was observed to occur between the oxide layers and substrate. This paper will discuss the significance of these results and consider the mechanisms responsible for degradation of this type of intermetallics in high sulphur and low oxygen environment with reference to their limit of temperature tolerance. (orig.)

Proposal of a postal system for Ir-192 sources calibration used in high dose rate brachytherapy with LiF:Mn:Ti thermoluminescent dosemeters

International Nuclear Information System (INIS)

Vieira, W.S.; Borges, J.C.; Almeida, C.E.V.

1998-01-01

A proposal in order to improve the brachytherapy quality control and to allow postal intercomparison of Ir-192 sources used in high dose rate brachytherapy has been presented. The LiF: Mn: Ti (TLD 100) detector has been selected for such purpose. The experimental array and the TLDs irradiation and calibration techniques, at the treatment units, have been specified in the light of more recent methodology of Ir-192 calibration sources. (Author)

Structural investigation and microwave characteristics of (Ba{sub 0.2}La{sub 0.8})Fe{sub 0.2}Mn{sub 0.4}Ti{sub 0.4}O{sub 3} absorbing materials

Energy Technology Data Exchange (ETDEWEB)

Manaf, Azwar [Dept. of Physics, Faculty of Mathematics and Natural Sciences, Indonesia of University (Indonesia); Adi, Wisnu Ari, E-mail: dwisnuaa@batan.go.id [Center for Technology of Nuclear Industry Material, National Nuclear Energy Agency (Indonesia)

2014-03-24

Synthesis and characterization of (Ba{sub 0.2}La{sub 0.8})Fe{sub 0.2}Mn{sub 0.4}Ti{sub 0.4}O{sub 3} absorbing material by mechanical alloying process has been performed. The absorbing material was prepared by oxide materials, namely BaCO{sub 3}, La{sub 2}O{sub 3}, TiO{sub 2}, Fe{sub 2}O{sub 3}, and MnCO{sub 3}. The mixture was milled for 10 h and then sintered at a temperature of 1000 ° C for 10 h. The refinement results of x-ray diffraction pattern of lanthanum manganite substituted with barium showed that the sample consisted of two phases, namely, La{sub 0.9125}MnO{sub 3} phase which has a structure monoclinic (I12/a1) with lattice parameters a = 5.527(1) Å, b = 5.572(1) Å and c = 7.810(1) Å, α = γ = 90° and β = 89.88(5)°, the unit cell volume of V = 240.57(8) Å{sup 3}, and the atomic density of ρ = 6.238 gr.cm{sup −3}. The microstructure analyses showed that the particle shapes was polygonal with the varied particle sizes of 1 ∼ 3 μm distributed homogeneously on the surface of the samples. The results of the electromagnetic wave absorption curve analysis by using a vector network analyzer (VNA) showed that the sample can absorb microwaves in the frequency range of 8-15 GHz with a very wide absorption bandwidth. It indicates that the as prepared absorber presents potential absorbing property in X and Ku-band. We concluded that the (Ba{sub 0.2}La{sub 0.8})Fe{sub 0.2}Mn{sub 0.4}Ti{sub 0.4}O{sub 3} material can be applied as a candidate absorber material of microwaves or electromagnetic wave.

Transient Liquid Phase Bonding of Cu-Cr-Zr-Ti Alloy Using Ni and Mn Coatings: Microstructural Evolution and Mechanical Properties

Science.gov (United States)

Venkateswaran, T.; Ravi, K. R.; Sivakumar, D.; Pant, Bhanu; Janaki Ram, G. D.

2017-08-01

High-strength copper alloys are used extensively in the regenerative cooling parts of aerospace structures. Transient liquid phase (TLP) bonding of a Cu-Cr-Zr-Ti alloy was attempted in the present study using thin layers of elemental Ni and Mn coatings applied by electroplating. One of the base metals was given a Ni coating of 4 µm followed by a Mn coating of 15 µm, while the other base metal was given only the Ni coating (4 µm). The bonding cycle consisted of the following: TLP stage—heating to 1030 °C and holding for 15 min; homogenization stage—furnace cooling to 880 °C and holding for 2 h followed by argon quenching to room temperature. Detailed microscopy and electron probe microanalysis analysis of the brazed joints were carried out. The braze metal was found to undergo isothermal solidification within the 15 min of holding time at 1030 °C. At the end of TLP stage, the braze metal showed a composition of Cu-17Ni-9Mn (wt.%) at the center of the joint with a steep gradient in Ni and Mn concentrations from the center of the braze metal to the base metal interfaces. After holding for 2 h at 880 °C (homogenization stage), the compositional gradients were found to flatten significantly and the braze metal was found to develop a homogeneous composition of Cu-11Ni-7Mn (wt.%) at the center of the joint. In lap-shear tests, failures were always found to occur in the base metal away from the brazed region. The copper alloy base metal was found to undergo significant grain coarsening due to high-temperature exposure during brazing and, consequently, suffer considerable reduction in yield strength.

Order parameters and magnetocrystalline anisotropy of off-stoichiometric D0{sub 22} Mn{sub 2.36}Ga epitaxial films grown on MgO (001) and SrTiO{sub 3} (001)

Energy Technology Data Exchange (ETDEWEB)

Lee, Hwachol; Sukegawa, Hiroaki, E-mail: sukegawa.hiroaki@nims.go.jp; Mitani, Seiji; Hono, Kazuhiro [National Institute for Materials Science (NIMS), Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan)

2015-07-21

We study the relationship between long range order parameters and the magnetocrystalline anisotropy of off-stoichiometric D0{sub 22} Mn{sub 2.36}Ga (MnGa) epitaxial films grown on MgO (001) and SrTiO{sub 3} (STO) (001) single crystalline substrates. MnGa films deposited on MgO (001) show rather large irregular variation in magnetization with increasing substrate temperature in spite of the improved long range order of total atomic sites. The specific site long range order of Mn-I site characterized in the [101] orientation revealed the fluctuation of the occupation fraction of two Mn atomic sites with elevated substrate temperature, which appears more relevant to the observed magnetization change than the long range order of the total atomic sites. In case of MnGa films grown on the lattice-matched STO (001), high long range order of the total atomic sites in spite of the existence of secondary phase represents that the lattice mismatch plays a crucial role in determining the atomic arrangement of Mn and Ga atoms in the off-stoichiometric compositional case of MnGa.

Mechanical properties of the Mg-14Ti-1Al-0.9Mn (%Wt) synthesized by physical vapour

International Nuclear Information System (INIS)

Garces, G.; Cristina, M. C.; Torralba, M.; Adeva, P.

2001-01-01

The mechanical properties of the alloy Mg-14% Ti-1% Al-0.9 Mn obtained by PVD techniques have been evaluated up to 300 degree centigree. The alloy presents a columnar grain microstructure, typical of the zone 2 of the structure zone model of MD, where surface diffusion takes place. The alloy tested in compression at room temperature presented a high yield stress, 360 MPa. This resistance to the plastic deformation is principally due to a solid solution hardening and small grain size. The yield stress decrease with the compression temperature. However, the alloy showed low fracture resistance, especially at room temperature. The presence of pores at the grain boundaries, results in the crack formation, running fast along the grain boundary. (Author) 13 refs

Supported manganese oxide on TiO{sub 2} for total oxidation of toluene and polycyclic aromatic hydrocarbons (PAHs): Characterization and catalytic activity

Energy Technology Data Exchange (ETDEWEB)

Aboukaïs, Antoine, E-mail: aboukais@univ-littoral.fr [Univ Lille Nord de France, 59000 Lille (France); Equipe Catalyse, UCEIV, EA 4492, MREI, ULCO, 59140 Dunkerque (France); Abi-Aad, Edmond [Univ Lille Nord de France, 59000 Lille (France); Equipe Catalyse, UCEIV, EA 4492, MREI, ULCO, 59140 Dunkerque (France); Taouk, Bechara [Laboratoire de Sécurité des procédés Chimiques (LSPC), EA 4704, INSA Rouen, Avenue de l' Université, 76801 Saint Etienne du Rouvray (France)

2013-11-01

Manganese oxide catalysts supported on titania (TiO{sub 2}) were prepared by incipient wetness impregnation method in order to elaborate catalysts for total oxidation of toluene and PAHs. These catalysts have been characterized by means of X-ray diffraction (XRD), electron paramagnetic resonance (EPR), temperature programmed reduction (TPR) and temperature programmed desorption (TPD). It has been shown that for the 5%Mn/TiO{sub 2} catalyst the reducibility and the mobility of oxygen are higher compared, in one side, to other x%Mn/TiO{sub 2} samples and, in another side, to catalysts where TiO{sub 2} support was replaced by γ-Al{sub 2}O{sub 3} or SiO{sub 2}. It has been shown that the content of manganese loading on TiO{sub 2} has an effect on the catalytic activity in the toluene oxidation. A maximum of activity was obtained for the 5%Mn/TiO{sub 2} catalyst where the total conversion of toluene was reached at 340 °C. This activity seems to be correlated to the presence of the Mn{sup 3+}/Mn{sup 4+} redox couple in the catalyst. When the Mn content increases, large particles of Mn{sub 2}O{sub 3} appear leading then to the decrease in the corresponding activity. In addition, compared to both other supports, TiO{sub 2} seems to be the best to give the best catalytic activity for the oxidation of toluene when it is loaded with 5% of manganese. For this reason, the latter catalyst was tested for the abatement of some PAHs. The light off temperature of PAHs compounds increases with increasing of benzene rings number and with decreasing of H/C ratio. All of PAHs are almost completely oxidized and converted at temperatures lower than 500 °C. - Highlights: • Preparation of x%MnO{sub 2}/TiO{sub 2} catalysts. • Catalytic oxidation tests of toluene and PAHs. • EPR, TPR and TPD characterizations of Mn(II) and Mn(IV) ions.

CaMn0.875Ti0.125O3 as oxygen carrier for chemical-looping combustion with oxygen uncoupling (CLOU)—Experiments in a continuously operating fluidized-bed reactor system

KAUST Repository

Rydé n, Magnus; Lyngfelt, Anders; Mattisson, Tobias

2011-01-01

Particles of the perovskite material CaMn0.875Ti0.125O3 has been examined as oxygen carrier for chemical-looping with oxygen uncoupling, and for chemical-looping combustion of natural gas, by 70h of experiments in a circulating fluidized-bed reactor

Enhanced photocatalytic degradation of dye under visible light on mesoporous microspheres by defects in manganese- and nitrogen-co-doped TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Feng, Lu; Jiang, Heng, E-mail: hjiang78@hotmail.com [Liaoning Shihua University, School of Chemistry and Materials Science (China); Zou, Mingming; Xiong, Fengqiang; Ganeshraja, Ayyakannu Sundaram; Pervaiz, Erum [Chinese Academy of Sciences, Dalian National Laboratory for Clean Energy, Dalian Institute of Chemical Physics (China); Liu, Yinan; Zou, Shunying [Dalian Environmental Protection Laboratory (China); Yang, Minghui, E-mail: myang@dicp.ac.cn [Chinese Academy of Sciences, Dalian National Laboratory for Clean Energy, Dalian Institute of Chemical Physics (China)

2016-09-15

Manganese- and nitrogen-co-doped mesoporous TiO{sub 2} microsphere photocatalysts are prepared by a simple sol–gel method with controllable sizes in the range of 400–500 nm and high surface area of 112 m{sup 2} g{sup −1}. Manganous acetate is the Mn source, and ammonia gas is the nitrogen source used. The dopants are found to be uniformly distributed in the TiO{sub 2} matrix. Interestingly, in (Mn,N)-co-doped TiO{sub 2}, we observe an effective indirect band gap of ~2.58 eV. (Mn,N)-co-doped mesoporous TiO{sub 2} microspheres show higher photocatalytic activity than Mn–TiO{sub 2} microspheres under visible light irradiation. Among the samples reported in this work, 0.2 at.% Mn doping and 500 °C 2-h nitriding condition give the highest photocatalytic activity. The observed photocatalytic activity in the (Mn,N)-co-doped TiO{sub 2} is attributed to the contribution from improved absorption due to trap levels of Mn, oxygen vacancies and N doping.Graphical AbstractManganese- and nitrogen-co-doped mesoporous TiO{sub 2} microspheres containing substitutional N, interstitial N and O vacancies show high visible light photocatalytic activity.

Proposal of a postal system for Ir-192 sources calibration used in high dose rate brachytherapy with LiF:Mn:Ti thermoluminescent dosemeters; Proposta de um sistema postal para a calibracao de fontes de {sup 192} Ir, utilizadas em braquiterapia de alta taxa de dose, com dosimetros termoluminescentes de LiF: Mn: Ti

Energy Technology Data Exchange (ETDEWEB)

Vieira, W.S.; Borges, J.C.; Almeida, C.E.V. [Instituto de Radioprotecao e Dosimetria. CNEN Caixa Postal 37750, 22780-160, Rio de Janeiro (Brazil)

1998-12-31

A proposal in order to improve the brachytherapy quality control and to allow postal intercomparison of Ir-192 sources used in high dose rate brachytherapy has been presented. The LiF: Mn: Ti (TLD 100) detector has been selected for such purpose. The experimental array and the TLDs irradiation and calibration techniques, at the treatment units, have been specified in the light of more recent methodology of Ir-192 calibration sources. (Author)

Transport and magnetoresistance effect in an oxygen-deficient SrTiO3/La0.67Sr0.33MnO3 heterojunction

International Nuclear Information System (INIS)

Wang Jing; Chen Chang-Le; Yang Shi-Hai; Luo Bing-Cheng; Duan Meng-Meng; Jin Ke-Xin

2013-01-01

An oxygen-deficient SrTiO 3 /La 0.67 Sr 0.33 MnO 3 heterojunction is fabricated on an SrTiO 3 (001) substrate by a pulsed laser deposition method. The electrical characteristics of the heterojunction are studied systematically in a temperature range from 80 K to 300 K. The transport mechanism follows I ∞ exp(eV/nkT) under small forward bias, while it becomes space charge limited and follows I ∞ V m(T) with 1.49 < m < 1.99 under high bias. Such a heterojunction also exhibits magnetoresistance (MR) effect. The absolute value of negative MR monotonically increases with temperature decreasing and reaches 26.7% at 80 K under H = 0.7 T. Various factors, such as strain and oxygen deficiency play dominant roles in the characteristics. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Enhanced magnetoresistance in La0.7Ca0.3Mn03/Nd0.7Ca0.3Mn03 epitaxial multilayers

International Nuclear Information System (INIS)

Sharma, Himanshu; Khan, Md. S.; Tomy, C.V.; Jain, Sourabh; Tulapurkar, Ashwin

2014-01-01

Magnanite multilayers of La 0.7 Ca 0.3 MnO 3 /Nd 0.7 Ca 0.5 MnO 3 have been fabricated on SrTiO 3 (100) substrate using Nd 0.7 Ca 0.5 MnO 3 as the spacer layers. An enhanced magnetoresistance (MR) of more than 80% is observed in the multilayers compared with LCMO thin film (∼50%). Result suggests that the interface strains between LCMO and NCMO layers may have influences on the transport properties and a suitable film structure could be used to increase the large low field magnetoresistance. (author)

Interdiffusion effect on strained La0.8Ba0.2MnO3 thin films by off-axis sputtering on SrTiO3 (100) substrates

International Nuclear Information System (INIS)

Chou, Hsiung; Hsu, S. G.; Lin, C. B.; Wu, C. B.

2007-01-01

Strained La 0.8 Ba 0.2 MnO 3 thin films on SrTiO 3 (100) substrate are grown by an off-axis sputtering technique. It is found that the ferromagnetic temperature T C increases for thinner films. Secondary ion mass spectroscopy indicates that Sr diffuses partially into the film, making it structurally nonuniform. The region close to the film/substrate interface acts as La 1-x (Sr y Ba 1-y ) x MnO 3 with a near negligible y for the as grown film and a non-negligible amount of y for the high-temperature postannealed film. The enhancement of T C is attributed to the combination of the strain and interdiffusion effects

Interdiffusion effect on strained La0.8Ba0.2MnO3 thin films by off-axis sputtering on SrTiO3 (100) substrates

Science.gov (United States)

Chou, Hsiung; Hsu, S. G.; Lin, C. B.; Wu, C. B.

2007-02-01

Strained La0.8Ba0.2MnO3 thin films on SrTiO3 (100) substrate are grown by an off-axis sputtering technique. It is found that the ferromagnetic temperature TC increases for thinner films. Secondary ion mass spectroscopy indicates that Sr diffuses partially into the film, making it structurally nonuniform. The region close to the film/substrate interface acts as La1-x(SryBa1-y)xMnO3 with a near negligible y for the as grown film and a non-negligible amount of y for the high-temperature postannealed film. The enhancement of TC is attributed to the combination of the strain and interdiffusion effects.

The microstructure and composition analysis of (Ba,Sr)O.6Fe_2_1_-_X)(Mn,Ti)_xO_3 (X = 0, 0,25; and 0,5)

International Nuclear Information System (INIS)

Wisnu Ari Adi; Azwar Manaf

2010-01-01

The raw materials were BaCO_3_' srCO_3_' Fe_2O_3_' MnCO_3 and TiO_2. The compound was synthesized by a solid state reaction method. The finely mixed powder was compacted at 5000 psi into pellets. These pellets were sintered in the electric chamber furnace THERMOLYNE at 1050 °C for 15 h with a heating cycle of 5°C/min ramp rate and cooled in the furnace to room temperature. The result showed that the X-ray diffraction pattern obtained can be identified as the SrO.6Fe_2O3 single phase (ICDD PDF 33-1340) for all samples according to the Hanawalt table. The microstructure analyses showed that the particle shapes are polygonal with the varied particle sizes of 2-5 μm distributed homogeneously on the surface of the samples. The element analysis showed that the compound compositions have already suitable to expectation. It is concluded that a single phase Mn-Ti substituted (Ba,Sr)O.6Fe_2O_3 have been made successfully suitable of compound composition was expected. (author)

Effect of laser power and scanning speed on laser deposited Ti6Al4V/TiB2 matrix composites

CSIR Research Space (South Africa)

Mokgalaka, MN

2012-10-01

Full Text Available Additive Manufacturing in Industry Conference, Kwa Maritane, Pilanesberg National Park, 31 October-2 November 2012 EFFECT OF LASER POWER AND SCANNING SPEED ON LASER DEPOSITED Ti6Al4V/TiB2 MATRIX COMPOSITES M.N. Mokgalaka2,1, S.L. Pityana1,2, A.P.I...

Uptake and translocation of Ti from nanoparticles in crops and wetland plants.

Science.gov (United States)

Jacob, Donna L; Borchardt, Joshua D; Navaratnam, Leelaruban; Otte, Marinus L; Bezbaruah, Achintya N

2013-01-01

Bioavailability of engineered metal nanoparticles affects uptake in plants, impacts on ecosystems, and phytoremediation. We studied uptake and translocation of Ti in plants when the main source of this metal was TiO2 nanoparticles. Two crops (Phaseolus vulgaris (bean) and Triticum aestivum (wheat)), a wetland species (Rumex crispus, curly dock), and the floating aquatic plant (Elodea canadensis, Canadian waterweed), were grown in nutrient solutions with TiO2 nanoparticles (0, 6, 18 mmol Ti L(-1) for P. vulgaris, T. aestivum, and R. crispus; and 0 and 12 mmol Ti L(-1) for E. canadensis). Also examined in E. canadensis was the influence of TiO2 nanoparticles upon the uptake of Fe, Mn, and Mg, and the influence of P on Ti uptake. For the rooted plants, exposure to TiO2 nanoparticles did not affect biomass production, but significantly increased root Ti sorption and uptake. R. crispus showed translocation of Ti into the shoots. E. canadensis also showed significant uptake of Ti, P in the nutrient solution significantly decreased Ti uptake, and the uptake patterns of Mn and Mg were altered. Ti from nano-Ti was bioavailable to plants, thus showing the potential for cycling in ecosystems and for phytoremediation, particularly where water is the main carrier.

Effect of HIP temperatures on the microstructure and mechanical properties of carbide dispersed Ti-48Al-1Mn mechanically alloyed compacts

International Nuclear Information System (INIS)

Ameyama, Kei; Hashii, Mitsuya; Imai, Nobuyuki; Fujii, Toshinori; Sasaki, Nobuyuki.

1996-01-01

The effect of hot isostatic pressing (HIP) temperature on the microstructure and mechanical properties of Ti-48 mol%Al-1 mol%Mn compacts fabricated by mechanical alloying was investigated. N-heptane was used as a process control agent for the mechanical alloying. The compacts HIP treated at 1173, 1373 or 1573 K showed an ultra-fine equiaxed grain structure, i.e., a microduplex structure, consisting of TiAl (γ) and Ti 2 AlC phases, and their average grain sizes were 185 nm, 510 nm and 1.5 μm, respectively. The γ phase was considered to be formed by an α → γ massive transformation during heating. On the other hand, the compacts HIP treated at 1623 or 1673 K showed quite different microstructures from the above HIP compacts. The 1623 K-HIP compact was composed of equiaxed γ grains, whose size was approximately 11.5 μm, rectangular shaped Ti 2 AlC particles, and a small amount of the grain boundary nucleated α phase. Although the 1673 K-HIP compact showed a microstructure similar to the 1623 K-HIP compact, the γ grains were coarsened to be approximately 27.8 μm in diameter and the Ti 2 AlC particles were more elongated rectangles. Furthermore, the amount of the grain boundary nucleated α phase was increased and the lamella α phase nucleated at γ twin boundaries was observed in the 1673 K-HIP compact. Mechanical properties determined by compressive testing at various temperatures made clear that the compacts HIP treated at 1173, 1373 or 1573 K have good workability at elevated temperatures and those HIP treated at 1623 or 1673 K have good high temperature strength. These mechanical properties were influenced significantly by the microstructure, especially by the grain size and morphology of the Ti 2 AlC phase. (author)

Characterization of jade and silicates of the jade family for application in radiation dosimetry

International Nuclear Information System (INIS)

Melo, Adeilson Pessoa de

2007-01-01

The main dosimetric properties of jade and of Brazilian silicates of the jade family were studied for application in radiation dosimetry of high doses. Jade is a common denomination of two different silicates: jadeite, Na Al(Si 2 O 6 ), and nephrite, Ca 2 (Mg, Fe) 5 (Si 4 O 11 ) 2 (OH) 2 , that belong to the subclasses of the pyroxenes and amphiboles respectively. The jade samples studied in this work were from: Austria, New Zealand, United States and Brazil. The Brazilian silicates of the jade family studied in this work were the amphiboles: tremolite,Ca 2 Mg 5 (Si 4 O 11 ) 2 (OH) 2 e actinolite, Ca 2 Fe 5 (Si 4 O 11 ) 2 (OH) 2 ; and the pyroxenes: rhodonite, MnSiO 3 and diopside, Ca Mg(Si 2 O 6 ). The mineralogical and chemical composition of these materials were obtained using the neutron activation analysis and X-ray diffraction techniques. The main dosimetric properties (emission curves, calibration curves, reproducibility, lower detection limits, angular and energy dependence, etc) were studied using the thermoluminescent (T L), thermally stimulated exo-emission (TSEE) and electronic paramagnetic resonance (EPR) techniques. The jade-Teflon and the silicate-Teflon samples present two T L peaks around 115 deg C (peak 1) and 210 deg C (peak 2). The calibration curves of the studied materials present a linear behaviour between 0.5 Gy and 1 kGy. The TSEE emission peak occurs at 240 deg C for all samples, and the calibration curves present a sub linear behaviour between 100 Gy and 20 kGy. In the case of the EPR technique, only jade USA has a potential application for radiation dosimetry. A static computational simulation of the most probable intrinsic and extrinsic defects in rhodonite was also realized. Among the basic defects, the Schottky defects of rhodonite are the most probable to occur and, among the extrinsic defects, the divalent and trivalent dopants present the best possibility of inclusion in rhodonite. (author)

A new, high energy rechargeable lithium ion battery with a surface-treated Li1.2Mn0.54Ni0.13Co0.13O2 cathode and a nano-structured Li4Ti5O12 anode

International Nuclear Information System (INIS)

Liu, Xiaoyu; Huang, Tao; Yu, Aishui

2015-01-01

Through elaborate design, a new rechargeable lithium ion battery has been developed by comprising a surface-treated Li 1.2 Mn 0.54 Ni 0.13 Co 0.13 O 2 cathode and a nano-structured Li 4 Ti 5 O 12 anode. After precondition Na 2 S 2 O 8 treatment, the initial coulombic efficiency of Li 1.2 Mn 0.54 Ni 0.13 Co 0.13 O 2 cathode has been significantly increased and can be compatible with that of the nano-structured Li 4 Ti 5 O 12 anode. The optimization of structure and morphology for both active electrode materials result in their remarkable electrochemical performances in respective lithium half-cells. Ultimately, the rechargeable lithium ion full battery consisting of both electrodes delivers a specific capacity of 99.0 mAh g −1 and a practical energy density of 201 Wh kg −1 , based on the total weight of both active electrode materials. Furthermore, as a promising candidate in the lithium ion battery field, this full battery also achieves highly attractive electrochemical performance with high coulombic efficiency, excellent cycling stability and outstanding rate capability. Thus the proposed battery displays broad practical application prospects for next generation of high-energy lithium ion battery. - Highlights: • The Li 1.2 Mn 0.54 Ni 0.13 Co 0.13 O 2 cathode is surface-treated by Na 2 S 2 O 8 . • The nano-sized Li 4 Ti 5 O 12 anode is obtained by a solid-state method. • A new Li 1.2 Mn 0.54 Ni 0.13 Co 0.13 O 2 /Li 4 Ti 5 O 12 lithium ion battery is developed. • The battery shows high coulombic efficiency, specific capacity and energy density. • The battery shows high capacity retention rate and good high-rate capability

Growth and in-plane magnetic anisotropy of inverse spinel Co{sub 2}MnO{sub 4} thin films

Energy Technology Data Exchange (ETDEWEB)

Koo, Taeyeong; Kim, Jaeyeong [Pohang University of Science and Technology, Pohang (Korea, Republic of); Song, Jonghyun [Chungnam National University, Daejeon (Korea, Republic of)

2014-11-15

Epitaxial Co{sub 2}MnO{sub 4} thin films were grown on Nb(0.1wt.)-doped SrTiO{sub 3} single-crystal substrates with (100) and (110) crystal orientations by using pulsed laser deposition. Their crystal structures and magnetic properties were investigated. Both samples exhibited ferrimagnetic transitions with enhanced transition temperatures. Isotropic M-H loops were observed on the in-plane surface of Co{sub 2}MnO{sub 4}(00l) grown on Nb(0.1wt)-doped SrTiO{sub 3}(100). Strong magnetic anisotropy was observed on the in-plane surface for Co{sub 2}MnO{sub 4} (ll0) grown on Nb(0.1wt)-doped SrTiO{sub 3}(110). A magnetic easy axis existed along the elongated tetragonal direction. This was attributed to the strong interplay between the spin and lattice degrees of freedom in the Co{sub 2}MnO{sub 4} thin film.

Magnetically tunable dielectric, impedance and magnetoelectric response in MnFe{sub 2}O{sub 4}/(Pb{sub 1−x}Sr{sub x})TiO{sub 3} composites thin films

Energy Technology Data Exchange (ETDEWEB)

Bala, Kanchan, E-mail: bala.kanchan1987@gmail.com [Department of Physics, Himachal Pradesh University, Shimla 171005 (India); Kotnala, R.K. [CSIR, National Physical Laboratory, Dr. K.S. Krishnan Road, New Delhi 110012 (India); Negi, N.S., E-mail: nsn_phy_hpu@yahoo.com [Department of Physics, Himachal Pradesh University, Shimla 171005 (India)

2017-02-15

We have synthesized piezomagnetic–piezoelectric composites thin films MnFe{sub 2}O{sub 4}/(Pb{sub 1−x}Sr{sub x})TiO{sub 3}, where x=0.1, 0.2, and 0.3, using the metalorganic deposition (MOD) reaction method. The structural and microstructural analysis using the X-ray diffraction (XRD), AFM, and SEM reveals the presence of homogenous growth of both pervoskite and spinel phases in the composite films. Our results show that all the composites films exhibit good multiferroic as well as considerable magnetoelectric coupling. The impedance (Z′ and Z″) and electrical modulus (M′ and M″) Nyquist plots show distinct electrical responses with the magnetic field. Our analyses suggest that this electrical response arises due to the coexistence of the high resistive phase and the comparatively conductive phase in the MFO/PST composite films. The maximum magnetoelectric coefficient (α) is found to be 4.29 V Oe{sup −1} cm{sup −1} and 2.82 V Oe{sup −1} cm{sup −1} for compositions x=0.1 and 0.2. These values are substantially larger than those reported for bilayer composites thin films in literature and make them interesting for room temperature device applications. - Highlights: • Influence of Sr doping on multiferroic and magnetoelectric properties composites thin films of MnFe{sub 2}O{sub 4} and (Pb, Sr)TiO{sub 3}. • Dielectric constant and dielectric loss with application of magnetic field. • Magnetically tunable AC electrical properties. • Magnetoelectric coupling in MnFe{sub 2}O{sub 4}/(Pb, Sr)TiO{sub 3} composite films by passive method.

Investigation of semi-insulating InP co-doped with Ti and various acceptors for use in X-ray detection

International Nuclear Information System (INIS)

Zdansky, K.; Gorodynskyy, V.; Kozak, H.; Pekarek, L.

2005-01-01

Semi-insulating InP single crystals co-doped with Zn and Ti and co-doped with Ti and Mn were grown by Czochralski technique. Wafers of these crystals were annealed for a long time at a high temperature and cooled slowly. The samples were characterized by temperature dependent resistivity and Hall coefficient measurements. The binding energies of Ti in semi-insulating InP co-doped with Ti and Zn and co-doped with Ti and Mn were found to differ which shows that Ti may occupy different sites in InP. The curves of Hall coefficient vs. reciprocal temperature deviate from straight lines at low temperatures due to electron and hole mixed conductance. The value of resistivity of the annealed semi-insulating InP co-doped with Ti and Mn reaches high resistivity at a reduced temperature easily achievable by thermo-electric devices which could make this material useable in X-ray detection. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Proton induced reactions on Ti, V, Mn, Fe, Co and Ni. Measurement and hybrid model analysis of integral excitation functions and their application in model calculation for the production of cosmogenic nuclides

International Nuclear Information System (INIS)

Stueck, R.

1983-01-01

By means of the stacked foil technique 67 excitation functions of p induced reactions on the target elements Ti, V, Mn, Fe, Co, and Ni were measured in the energy range between 45 and 200 MeV. For residual nuclei with 42 [de

Magnetic and electronic properties of SrMnO3 thin films

Science.gov (United States)

Mandal, Arup Kumar; Panchal, Gyanendra; Choudhary, R. J.; Phase, D. M.

2018-05-01

Single phase hexagonal bulk SrMnO3 (SMO) was prepared by solid state route and it was used for depositing thin films by pulsed laser deposition (PLD) technique on single crystalline (100) oriented SrTiO3 (STO) substrate. X-ray diffraction shows that the thin film is deposited in cubic SrMnO3 phase. From X-ray absorption at the Mn L edge we observed the mixed valency of Mn (Mn3+& Mn4+) due to strain induced by the lattice mismatching between SMO and STO. Due to this mixed valency of Mn ion in SMO film, the ferromagnetic nature is observed at lower temperature because of double exchange. After post annealing with very low oxygen partial pressure, magnetic and electronic property of SMO films are effectively modified.

Conduction Mechanism by Using CBH Model in Fe3+ and Mn3+ Ion Modified Pb(Zr0.65−xAxTi0.35O3 (A = Mn3+/Fe3+ Ceramics

Directory of Open Access Journals (Sweden)

Niranjan Sahu

2013-01-01

Full Text Available Polycrystalline samples of manganese and iron substituted lead zirconium titanate (PZT with general formula Pb(Zr0.65−xAxTi0.35O3 (A = Mn3+ and Fe3+ ceramics have been synthesized by high temperature solid state reaction technique. X-ray diffraction (XRD patterns were recorded at room temperature to study the crystal structure. All the patterns could be refined by employing the Rietveld method to R3c space group with rhombohedral symmetry. Microstructural properties of the materials were analyzed by scanning electron microscope (SEM, and compositional analysis was carried out by energy dispersive spectrum (EDS measurements. All the materials exhibit ferroelectric to paraelectric transition. The variation of dielectric constant and loss tangent with temperature and frequency is investigated. The decrease of activation energy and increases of AC conductivity with the Fe3+ or Mn3+ ion concentration have been observed. The AC conductivity has been analyzed by the power law. The frequency exponent with the function of temperature has been analyzed by assuming that the AC conduction mechanism is the correlated barrier hopping (CBH model. The conduction in the present sample is found to be of bipolaron type for Mn3+ ion-doped sample. However, the conduction mechanism could not be explained by CBH model for Fe3+ ion-doped sample.

Structure and magnetic properties of La{sub 2/3}Sr{sub 1/3}MnO{sub 3}/CaMnO{sub 3} multilayers

Energy Technology Data Exchange (ETDEWEB)

Granada, Mara [Centro Atomico Bariloche and Instituto Balseiro, CNEA-UNC, Av. Bustillo 9500, 8400 San Carlos de Bariloche (Argentina)]. E-mail: granadam@cab.cnea.gov.ar; Sirena, Martin [Centro Atomico Bariloche and Instituto Balseiro, CNEA-UNC, Av. Bustillo 9500, 8400 San Carlos de Bariloche (Argentina); Steren, Laura B. [Centro Atomico Bariloche and Instituto Balseiro, CNEA-UNC, Av. Bustillo 9500, 8400 San Carlos de Bariloche (Argentina); Leyva, Gabriela [Depto. de Fisica, Centro Atomico Constituyentes, CNEA, Av. Gral. Paz y Constituyentes, 1650 San Martin (Argentina)

2004-12-31

Structural and magnetic properties of manganite-based multilayers, La{sub 2/3}Sr{sub 1/3}MnO{sub 3}/CaMnO{sub 3}, composed of ferromagnetic metals and antiferromagnetic insulator barriers are investigated in this work. Compounds of similar lattice parameters were used to build the samples, so we expect an excellent stacking of the different layers along the structure. To get a first insight of this system, the crystalline structure of a series of samples, grown on (1 0 0) SrTiO{sub 3} and (1 0 0) MgO single-crystalline substrates, has been studied. X-ray diffraction patterns show that the structure is strongly textured in the (1 0 0) direction when grown on SrTiO{sub 3}, regardless the composition of the bottom layer. A different result is found on the same system grown on MgO: when the buffer layer is CaMnO{sub 3}, the structure grows in the (1 1 0) orientation while it grows in the (1 0 0) direction when the bottom layer is La{sub 2/3}Sr{sub 1/3}MnO{sub 3}. Magnetic coupling of the ferromagnetic layers across the antiferromagnetic spacer has been studied with magnetization measurements.

Severe plastic deformation of melt-spun shape memory Ti2NiCu and Ni2MnGa alloys

International Nuclear Information System (INIS)

Pushin, Vladimir G.; Korolev, Alexander V.; Kourov, Nikolai I.; Kuntsevich, Tatiana E.; Valiev, Eduard Z.; Yurchenko, Lyudmila I.; Valiev, Ruslan Z.; Gunderov, Dmitrii V.; Zhu, Yuntian T.

2006-01-01

This paper describes the influence of severe plastic deformation (SPD) on the structure, phase transformations, and physical properties of melt-spun Ti 2 NiCu-based and Ni 2 MnGa-based shape memory intermetallic alloys. It was found that the SPD by high pressure torsion (HPT) at room temperature can be effectively used for the synthesis of bulk nanostructured states in these initially submicro-grained or amorphized alloys obtained by melt-spinning method in the form of a ribbon. The subsequent low-temperature annealing of HPT-processed alloys leads to formation of homogeneous ultrafine nano-grained structure. This is connected with a very high degree and high homogeneity of deformation at SPD in the whole volume of deformed samples. (author)

Disorder influence on the magnetic properties of La0.55Sr0.45MnO3/SrTiO3 superlattices

International Nuclear Information System (INIS)

Haberkorn, N.; Sirena, M.; Guimpel, J.; Steren, L.B.

2004-01-01

The structural and physical properties of La 0.55 Sr 0.45 MnO 3 /SrTiO 3 superlattices grown by magnetron sputtering are studied. Two deposition temperatures and different mismatched substrates and buffer layers were used. The structure was determined by refinement through X-ray diffraction pattern fitting. The results indicate 1 unit cell (u.c.) interdiffusion at the interfaces and a 1 u.c. layer thickness fluctuation, i.e. roughness. In-plane hysteresis loops show the expected ferromagnetic behavior, while the perpendicular-to-plane hysteresis loops show anomalies which could evidence magnetic domain size inhomogeneities and stress

Vibrational localized motions of hydrogen in the storage compound Ti0.8 Zr0.2 CrMnH3 studied by slow neutron inelastic scattering

International Nuclear Information System (INIS)

Mestnik Filho, J.; Vinhas, L.A.

1988-08-01

The vibrational localized motions of hydrogen in the storage compound Ti 0.8 Zr 0.2 CrMnH 3 have been studied by slow neutron scattering, utilizing a berilium-filter-time-of-flight spectrometer. An energy distribution, consisting of therre peaks 50 MeV wide (FWHM), corresponding to the energy transfer of 85, 115 and 141 MeV has been observed and was attributed to hydrogen localized vibrations in three types of interstices which differs in composition of Ti and Zr atoms. From the analysis of the observed peaks intensities, it was concluded that the lowest measured hydrogen vibrational frequency is correlated with interstices that are rich in zirconium atoms whereas the highest frequency is due o interstices rich in titanium atoms. Therefore the larger radius of the the Zr atoms leads to the formation of interstices with larger intersticial hole sizes, which, in turn, makes possible the absorption of hydrogen in this compound, in contrast to an isostructural compound which contains only atoms with smaller radii, like Ti, in place of the atomic group Ti 0.8 Zr 0.2 . (author) [pt

Crystallographic and electronic structure of the Ca2TiMnO6 double perovskite

International Nuclear Information System (INIS)

López, J.P. Garzón; Cardona, R.; Santos, A. Sarmiento; Téllez, D.A. Landínez; Roa-Rojas, J.

2014-01-01

In this work, we report synthesis and crystalline structure study of the Ca 2 TiMnO 6 complex perovskite, by X-ray diffraction experiments and through the application of the Rietveld refinement using the GSAS code. Results revealed the crystallization of the system in a tetragonal perovskite with the characteristic structure given by I4/m (#87) space group and lattice parameters a=5.339(4) Å and c=7.736(6) Å. Ab initio calculations of density of states (DOS) and electronic structure were carried out for this perovskite-like system, by the Density Functional Theory (DFT) and using the Full-potential Linearized Augmented Plane Waves (FP-LAPW) method. The exchange-correlation potential was treated using the Generalized Gradient Approximation (GGA). All calculations were carried-out using spin polarization. For the up spin orientation the compound has a semiconducting behavior and for down spin polarization it behaves like a conductor. The calculated effective magnetic moment in cell was 4.02 μ B , which is close to the expected value calculated from Hund's rules

Impedance and magnetoelectric characteristics of (1 - x)BaTiO3- xLa0.7Sr0.3MnO3 ( x = 0.1 and 0.3) nano-composites

Science.gov (United States)

Nayek, C.; Murugavel, P.; Dinesh Kumar, S.; Subramanian, V.

2015-08-01

We have synthesized the phase-pure (1 - x)BaTiO3- xLa0.7Sr0.3MnO3 ( x = 0.1 and 0.3) magnetoelectric composites without interdiffusion among the existing phases. The magnetic measurements revealed an anomaly at the ferroelectric Curie temperature (393 K) of BaTiO3, and the dielectric data revealed an anomaly at the ferromagnetic transition temperature (360 K) of La0.7Sr0.3MnO3 ascertaining the magnetoelectric coupling in the composite. Impedance analysis indicated dipolar polarization contributions to the dielectric spectrum with two non-Debye-type relaxations. Both the grain and grain boundary contributions were present in the system with dominant grain boundary effect in all the composites. The composites show semiconducting behavior with the barrier hopping-type conducting mechanism. To avoid the free charge carrier and the space charge contributions, the magnetoelectric response was measured at high frequency range. The maximum values of magnetoelectric voltage coefficient measured at 100 kHz were 221 and 219 mV/Oe-cm for x = 0.1 and 0.3 samples, respectively.

Influence of Mn contents in 0Cr18Ni10Ti thin wall stainless steel tube on TIG girth weld quality

Science.gov (United States)

Liu, Bo

2017-03-01

Three kinds of cold worked 0Cr18Ni10Ti thin wall stainless steel tubes with the manganese contents of 1.27%, 1.35% and 1.44% and the cold worked 0Cr18Ni10Ti stainless steel end plug with manganese content of 1.35% were used for TIG girth welding in the present investigation. The effect of different manganese contents in stainless steel tube on weld quality was studied. The results showed that under the same welding conditions, the metallographic performance of the girth weld for the thin wall stainless steel tube with the manganese element content 1.44% welded with end plug was the best. Under the appropriate welding conditions, the quality of the girth weld increased with the increase of the manganese content till 1.44%. It was found that in the case of the Mn content of 1.44%, and under the proper welding condition the welding defects, such as welding cracks were effectively avoided, and the qualified weld penetration can be obtained.. It is concluded that the appropriate increase of the manganese content can significantly improve the TIG girth weld quality of the cold worked 0Cr18Ni10Ti stainless steel tube.

Magnetocrystalline anisotropy and magnetic domain structure of ErFe11Ti and HoFe11Ti compounds

International Nuclear Information System (INIS)

Pastushenkov, Yury G.; Skokov, Konstantin P.; Skourski, Yury; Lebedeva, Ludmila; Ivanova, Tatyana; Grushichev, Anton; Mueller, Karl-Hartmut

2006-01-01

Tetragonal ThMn 12 -type single crystalline ErFe 11 Ti and HoFe 11 Ti samples have been investigated by magnetization measurements and by observations of the magnetic domain structure at various temperatures between 10 and 300K. The magnetic structure of ErFe 11 Ti changes from room temperature 'easy axis' (c-axis) type to conical at spin-reorientation temperature T SR =50K. The HoFe 11 Ti has a metastable anisotropy energy minimum in the a-direction at T<40K. It leads to a first-order magnetization process detected by magnetization measurements along the a-axis in this temperature region

Thickness dependence of La{sub 0.7}Sr{sub 0.3}MnO{sub 3}/PbZr{sub 0.2}Ti{sub 0.8}O{sub 3} magnetoelectric interfaces

Energy Technology Data Exchange (ETDEWEB)

Zhou, Jinling; Trappen, Robbyn; Frye, Charles; Wolfe, Evan; Holcomb, Mikel Barry, E-mail: mikel.holcomb@mail.wvu.edu [Department of Physics and Astronomy, West Virginia University, Morgantown, West Virginia 26506 (United States); Tra, Vu Thanh; Lin, Jiunn-Yuan [Institute of Physics, National Chiao Tung University, 30010 Hsinchu, Taiwan (China); Dong, Shuai [Department of Physics, Southeast University, 211189 Nanjing (China); Marcus, Matthew A.; Jenkins, Catherine [Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); White, Ryan [National Institute of Standards and Technology, Gaithersburg, Maryland 20899 (United States); Polisetty, Srinivas [Department of Physics and Astronomy, West Virginia University, Morgantown, West Virginia 26506 (United States); Department of Chemical Engineering and Material Science, University of Minnesota, Minneapolis, Minnesota 55455 (United States); LeBeau, James M. [Department of Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States); Chu, Ying-Hao [Department of Materials Science and Engineering, National Chiao Tung University, 30010 Hsinchu, Taiwan (China); Institute of Physics, Academia Sinica, 105 Taipei, Taiwan (China)

2015-10-05

Magnetoelectric materials have great potential to revolutionize electronic devices due to the coupling of their electric and magnetic properties. Thickness varying La{sub 0.7}Sr{sub 0.3}MnO{sub 3} (LSMO)/PbZr{sub 0.2}Ti{sub 0.8}O{sub 3} (PZT) heterostructures were built and measured in this article by valence sensitive x-ray absorption spectroscopy. The sizing effects of the heterostructures on the LSMO/PZT magnetoelectric interfaces were investigated through the behavior of Mn valence, a property associated with the LSMO magnetization. We found that Mn valence increases with both LSMO and PZT thickness. Piezoresponse force microscopy revealed a transition from monodomain to polydomain structure along the PZT thickness gradient. The ferroelectric surface charge may change with domain structure and its effects on Mn valence were simulated using a two-orbital double-exchange model. The screening of ferroelectric surface charge increases the electron charges in the interface region, and greatly changes the interfacial Mn valence, which likely plays a leading role in the interfacial magnetoelectric coupling. The LSMO thickness dependence was examined through the combination of two detection modes with drastically different attenuation depths. The different length scales of these techniques' sensitivity to the atomic valence were used to estimate the depth dependence Mn valence. A smaller interfacial Mn valence than the bulk was found by globally fitting the experimental results.

Tailoring the Activity for Oxygen Evolution Electrocatalysis on Rutile TiO2(110) by Transition-Metal Substitution

DEFF Research Database (Denmark)

Garcia-Mota, Monica; Vojvodic, Aleksandra; Metiu, Horia

2011-01-01

The oxygen evolution reaction (OER) on the rutile M-TiO2(110) (M = V, Nb, Ta, Cr, Mo, W, Mn, Fe, Ru, Ir, Ni) surfaces was investigated by using density functional theory calculations. The stability of different doped TiO2 systems was analyzed. The scaling relationship between the binding energies...... of OER intermediates (HOO* versus HO*) is found to follow essentially the same trend as for undoped oxides. Our theoretical analysis shows a lower overpotential associated with OER on the doped M-TiO2(110) than on the undoped TiO2(110). The theoretical activity of Cr-, Mo-, Mn-, and Ir-doped TiO2...

La2/3Sr1/3MnO3-La0.1Bi0.9MnO3 heterostructures for spin filtering

Science.gov (United States)

Gajek, M.; Bibes, M.; Varela, M.; Fontcuberta, J.; Herranz, G.; Fusil, S.; Bouzehouane, K.; Barthélémy, A.; Fert, A.

2006-04-01

We have grown heterostructures associating half-metallic La2/3Sr1/3MnO3 (LSMO) bottom electrodes and ferromagnetic La0.1Bi0.9MnO3 (LBMO) tunnel barriers. The layers in the heterostructures have good structural properties and top LBMO films (4 nm thick) have a very low roughness when deposited onto LSMO/SrTiO3(1.6 nm) templates. The LBMO films show an insulating behavior and a ferromagnetic character that are both preserved down to very low thicknesses. They are thus suitable for being used as tunnel barriers. Spin-dependent transport measurements performed on tunnel junctions defined from LSMO/SrTiO3/LBMO/Au samples show a magnetoresistance of up to ~90% at low temperature and bias. This evidences a spin-filtering effect by the LBMO layer, with a spin-filtering efficiency of ~35%.

Effect of the temperature, strain rate and microstructure on flow and fracture characteristics of Ti-45Al-2Nb-2Mn+0.8vol.% TiB2 XD alloy

Science.gov (United States)

Erice, B.; Pérez-Martín, M. J.; Cendón, D. A.; Gálvez, F.

2012-05-01

A series of quasi-static and dynamic tensile tests at varying temperatures were carried out to determine the mechanical behaviour of Ti-45Al-2Nb-2Mn+0.8vol.% TiB2 XD as-HIPed alloy. The temperature for the tests ranged from room temperature to 850 ∘C. The effect of the temperature on the ultimate tensile strength, as expected, was almost negligible within the selected temperature range. Nevertheless, the plastic flow suffered some softening because of the temperature. This alloy presents a relatively low ductility; thus, a low tensile strain to failure. The dynamic tests were performed in a Split Hopkinson Tension Bar, showing an increase of the ultimate tensile strength due to the strain rate hardening effect. Johnson-Cook constitutive relation was used to model the plastic flow. A post-testing microstructural of the specimens revealed an inhomogeneous structure, consisting of lamellar α2 + γ structure and γ phase equiaxed grains in the centre, and a fully lamellar structure on the rest. The assessment of the duplex-fully lamellar area ratio showed a clear relationship between the microstructure and the fracture behaviour.

High temperature strength and aging behavior of 12%Cr-15%Mn austenitic steels

International Nuclear Information System (INIS)

Miyahara, Kazuya; Bae, Dong-Su; Sakai, Hidenori; Hosoi, Yuzo

1993-01-01

High Mn-Cr austenitic steels are still considered to be an important high temperature structural material from the point of view of reduced radio-activation. The objective of the present study is to make a fundamental research of mechanical properties and microstructure of 12%Cr-15%Mn austenitic steels. Especially the effects of alloying elements of V and Ti on the mechanical properties and microstructure evolution of high Mn-Cr steels were studied. Precipitation behaviors of carbides, nitrides and σ phase are investigated and their remarkable effects on the high temperature strength are found. The addition of V was very effective for strengthening the materials with the precipitation of fine VN. Ti was also found to be beneficial for the improvement of high temperature strength properties. The results of high temperature strengths of the 12Cr-15Mn austenitic steels were compared with those of the other candidate and/or reference materials, for example, JFMS (modified 9Cr-2Mo ferritic stainless steel) and JPCAs (modified 316 austenitic stainless steels). (author)

Electric field modulated conduction mechanism in Al/BaTiO3/La0.67Sr0.33MnO3 heterostructures

KAUST Repository

Zheng, Dongxing; Li, Dong; Gong, Junlu; Jin, Chao; Li, Peng; Zhang, Xixiang; Bai, Haili

2017-01-01

Mediating a metastable state is a promising way to achieve a giant modulation of physical properties in artificial heterostructures. A metastable state La0.67Sr0.33MnO3 (LSMO) layer suffering tensile strain was grown on MgO substrates. Incorporating with the ferroelectric BaTiO3 (BTO) layer, an accumulation or depletion state controlled by electric fields can be formed at the BTO/LSMO interface, which drives a switching of the conduction mechanism between space charge limited conduction and Poole-Frenkel emission, corresponding to the low and high resistance states. Our results lighten an effective way for electric-field modulated resistance states in multiferroic magnetoelectric devices.

Electric field modulated conduction mechanism in Al/BaTiO3/La0.67Sr0.33MnO3 heterostructures

KAUST Repository

Zheng, Dongxing

2017-08-08

Mediating a metastable state is a promising way to achieve a giant modulation of physical properties in artificial heterostructures. A metastable state La0.67Sr0.33MnO3 (LSMO) layer suffering tensile strain was grown on MgO substrates. Incorporating with the ferroelectric BaTiO3 (BTO) layer, an accumulation or depletion state controlled by electric fields can be formed at the BTO/LSMO interface, which drives a switching of the conduction mechanism between space charge limited conduction and Poole-Frenkel emission, corresponding to the low and high resistance states. Our results lighten an effective way for electric-field modulated resistance states in multiferroic magnetoelectric devices.

Hydrothermal synthesis, structural and physico-chemical characterizations of two Nasicon phosphates: M0.50IITi2(PO4)3 (M = Mn, Co)

International Nuclear Information System (INIS)

Essehli, Rachid; Bali, Brahim El; Benmokhtar, S.; Fejfarova, Karla; Dusek, Michal

2009-01-01

The family of titanium Nasicon-phosphates of generic formula M 0.5 II Ti 2 (PO 4 ) 3 has been revisited using hydrothermal techniques. Two phases have been synthesized: Mn 0.5 II Ti 2 (PO 4 ) 3 (MnTiP) and Co 0.5 II Ti 2 (PO 4 ) 3 (CoTiP). Single crystal diffraction studies show that they exhibit two different structural types. Mn 0.5 II Ti 2 (PO 4 ) 3 phosphate crystallizes in the R-3 space group, with the cell parameters a = 8.51300(10) A and c = 21.0083(3) A (V = 1318.52(3) A 3 and Z = 6). The Co 0.5 II Ti 2 (PO 4 ) 3 phosphate crystallizes in the R-3c space group, with a = 8.4608(9) A and c = 21.174(2) A (V = 1312.7(2) A 3 and Z = 6). These two compounds are clearly related to the parent Nasicon-type rhombohedral structure, which can be described using [Ti 2 (PO 4 ) 3 ] framework composed of two [TiO 6 ] octahedral interlinked via three [PO 4 ] tetrahedra. 31 P magic-angle spinning nuclear magnetic resonance (MAS-NMR) data are presented as supporting data. Curie-Weiss-type behavior is observed in the magnetic susceptibility. The phases are also characterized by IR spectroscopy and UV-visible.

Correlation between atomic structure and magnetic properties of La0.7Ca0.3MnO3 thin films grown on SrTiO3 (1 0 0)

International Nuclear Information System (INIS)

Rubio-Zuazo, J.; Andres, A. de; Taboada, S.; Prieto, C.; Martinez, J.L.; Castro, G.R.

2005-01-01

The crystallographic structure of La 0.7 Ca 0.3 MnO 3 (LCMO) ultra-thin films grown on SrTiO 3 (0 0 1) has been investigated by surface X-ray diffraction (SXD) and the correlation between their transport and magnetic properties and crystallographic structure is discussed. LCMO thin films in a thickness range between 2.4 and 27 nm were grown by DC-sputtering on SrTiO 3 (0 0 1). We distinguish two different crystallographic structures associated to the 2.4 and 27 nm thin films, respectively. The 27 nm film structure corresponds to a tetragonal perovskite (space group Pbnm), as has been reported for bulk LCMO. For the 2.4 nm film the La/Ca ions are located at the regular position of an ideal perovskite and the MnO 6 octahedrons are aligned along the c-axis. The MnO 2 stacking layer (basal plane) is distorted and coplanar to the a-b crystallographic axis with an anti-correlation between octahedron layers. This observed distortion is not compatible with the Pbnm space group. The new phase, which cannot be excluded to coexist at the interface of thicker films, can be described, as an example, through an I4/mcm or Pbcn space group. Based on the observed structure, plausible models to explain their transport and magnetic behaviour are proposed. For the 2.4 nm film, an octahedron in-plane (basal plane) distortion induced by the substrate is observed. Thicker films behave structurally and magnetically as bulk-like materials

Photoluminescence of crystalline and disordered BTO:Mn powder: Experimental and theoretical modeling

International Nuclear Information System (INIS)

Gurgel, M.F.C.; Espinosa, J.W.M.; Campos, A.B.; Rosa, I.L.V.; Joya, M.R.; Souza, A.G.; Zaghete, M.A.; Pizani, P.S.; Leite, E.R.; Varela, J.A.; Longo, E.

2007-01-01

Disordered and crystalline Mn-doped BaTiO 3 (BTO:Mn) powders were synthesized by the polymeric precursor method. After heat treatment, the nature of visible photoluminescence (PL) at room temperature in amorphous BTO:Mn was discussed, considering results of experimental and theoretical studies. X-ray diffraction (XRD), PL, and UV-vis were used to characterize this material. Rietveld refinement of the BTO:Mn from XRD data was used to built two models, which represent the crystalline BTO:Mn (BTO:Mn c ) and disordered BTO:Mn (BTO:Mn d ) structures. Theses models were analyzed by the periodic ab initio quantum mechanical calculations using the CRYSTAL98 package within the framework of density functional theory at the B3LYP level. The experimental and theoretical results indicated that PL is related with the degree of disorder in the BTO:Mn powders and also suggests the presence of localized states in the disordered structure

Precipitation sensitivity to alloy composition in Fe-Cr-Mn austenitic steels developed for reduced activation for fusion application

International Nuclear Information System (INIS)

Maziasz, P.J.; Klueh, R.L.

1988-01-01

Special austenitic steels are being designed in which alloying elements like Mo, Nb, and Ni are replaced with Mn, W, V, Ti, and/or Ta to reduce the long-term radioactivity induced by fusion reactor irradiation. However, the new steels still need to have properties otherwise similar to commercial steels like type 316. Precipitation strongly affects strength and radiation-resistance in austenitic steels during irradiation at 400--600/degree/C, and precipitation is also usually quite sensitive to alloy composition. The initial stage of development was to define a base Fe-Cr-Mn-C composition that formed stable austenite after annealing and cold-working, and resisted recovery or excessive formation of coarse carbide and intermetallic phases during elevated temperature annealing. These studies produced a Fe-12Cr-20Mn-0.25C base alloy. The next stage was to add the minor alloying elements W, Ti, V, P, and B for more strength and radiation-resistance. One of the goals was to produce fine MC precipitation behavior similar to the Ti-modified Fe-Cr-Ni prime candidate alloy (PCA). Additions of Ti+V+P+B produced fine MC precipitation along network dislocations and recovery/recrystallization resistance in 20% cold worked material aged at 800/degree/C for 166h, whereas W, Ti, W+Ti, or Ti+P+B additions did not. Addition of W+Ti+V+P+B also produced fine MC, but caused some σ phase formation and more recrystallization as well. 29 refs., 14 figs., 9 tabs

The effect of addition of various elements on properties of NiTi-based shape memory alloys for biomedical application

Science.gov (United States)

Kök, Mediha; Ateş, Gonca

2017-04-01

In biomedical applications, NiTi and NiTi-based alloys that show their shape memory effects at body temperature are preferred. In this study, the purpose is to produce NiTi and NiTi-based alloys with various chemical rates and electron concentrations and to examine their various physical properties. N45Ti55, Ni45Ti50Cr2.5Cu2.5, Ni48Ti51X (X=Mn, Sn, Co) alloys were produced in an arc melter furnace in this study. After the homogenization of these alloys, the martensitic phase transformation temperatures were determined with differential-scanner calorimeter. The transformation temperature was found to be below the 37 ° C (body temperature) in Ni45Ti50Cr2.5Cu2.5, Ni48Ti51X (X=Mn, Co) alloys; and the transformation temperature of the N45Ti55, Ni48Ti51Sn alloys was found to be over 37 ° C . Then, the micro and crystal structure analyses of the alloys were made, and it was determined that Ni45Ti50Cr2.5Cu2.5, Ni48Ti51X (X=Mn, Co) alloys, which were in austenite phase at room temperature, included B2 (NiTi) phase and Ti2Ni precipitation phase, and the alloys that were in the martensite phase at room temperature included B19ı (NiTi) phase and Ti2Ni phase. The common phase in both alloy groups is the Ti2Ni phase, and this type of phase is generally seen in NiTi alloys that are rich in titanium (Ti-rich).

Explosive device of conduit using Ti Ni alloy

Directory of Open Access Journals (Sweden)

A. Yu. Kolobov

2014-01-01

Full Text Available Presently, materials have been developed which are capable at changing temperate to return significant inelastic deformations, exhibit rubber-like elasticity, convert heat into mechanical work, etc. The aggregate of these effects is usually called the shape memory effect.At present a great number of compounds and alloys with a shape memory effect has been known.These are alloys based on titanium nickelide (TiNi, copper-based alloys (Cu-Al, Cu-Sn, Cu-Al-Ni, Cu-Zn-Si, etc., gold and silver (Ag-Cd, Au-Ag-Cd, Au-Cd-Cu, Au-Zn-Cu, etc., manganese (Mn-Cr, Fe-Cu, Mn-Cu-Ni, Mn-Cu-Zr, Mn-Ni, etc., iron (Fe-Mn, Fe-Ni, Fe-Al, etc., and other compounds.The alloys based on titanium nickelide (nitinol are the most widely used.Alloys with shape memory effect find various applications in engineering and medicine, namely connecting devices, actuators, transformable design, multipurpose medical implants, etc.There is a task of breaking fuel conduit during separating the spacecraft from the rocket in space technology.The paper examines the procedure for design calculation of the separating device of conduit with the use of Ti-Ni alloy. This device can be used instead of the pyro-knives.The device contains two semi-rings from Ti-Ni alloy. In the place of break on the conduit an annular radius groove is made.At a temperature of martensite passage the semi-rings undergo deformation and in the strained state are set in the device. With heating to the temperature of the austenitic passage of bushing macro-deformation the energy stored by the nitinol bushing is great enough to break the conduit on the neck.The procedures of design calculation and response time of device are given.

Low temperature self-assembled growth of rutile TiO2/manganese oxide nanocrystalline films

Science.gov (United States)

Sun, Zhenya; Zhou, Daokun; Du, Jianhua; Xie, Yuxing

2017-10-01

We report formation of rutile TiO2 nanocrystal at low temperature range in the presence of α-MnO2 which self-assembled onto sulfanyl radical activated silicon oxide substrate. SEM, HRTEM, XPS and Raman spectroscopy were used to study the morphology and oxidation state of synthesised crystals. The results showed that when the α-MnO2 was reduced to Mn3O4, it induced the formation of rutile instead of anatase phase in the TiCl4-HCl aqueous system. The finding will promote the understanding of phase transformation mechanism when manganese oxide and titanium oxide co-exist in soil and water environment.

Synthesis and property of spinel porous ZnMn2O4 microspheres

Science.gov (United States)

Guo, N.; Wei, X. Q.; Deng, X. L.; Xu, X. J.

2015-11-01

Mesoporous ternary zinc manganese oxides on the Ti sheet substrate are prepared by easy and fast hydrothermal method for the first time. The obtained ZnMn2O4 materials with homogenously distributed pores have been characterized by XRD, SEM and Raman spectra, which show the good crystal phase and particles for improving supercapacitive performance. XRD and SEM images show that the as-prepared samples have good crystallinity, and ZnMn2O4 microsphere has an average diameter of 10 μm. In addition, ZnMn2O4 are also characterized in 2 M KOH solution using three-electrode system. In the work, we study that different substrates (Ti, carbon and nickel foam) have an important effect on the electrochemical performance of the samples. The research of cyclic voltammogram (CV) indicates that the obtained specific capacitance (155 F g-1) values on nickel foam substrate for the ZnMn2O4 microspheres are higher than the values reported for some inexpensive oxides. However, the specific capacitance of all ZnMn2O4 samples has almost no change at two different scan rates which shows good long-term cycling stability. The electrochemical impedance spectroscopy with a small resistance reveals that the as-synthesized samples have good frequency response characteristics. These results indicate that the unique ZnMn2O4 electrode would be a promising electrode for high-performance supercapacitor applications.

Corrosion Resistance and Pitting Behaviour of Low-Carbon High-Mn Steels in Chloride Solution

Directory of Open Access Journals (Sweden)

Grajcar A.

2016-06-01

Full Text Available Corrosion resistance of the X4MnSiAlNbTi27-4-2 and X6MnSiAlNbTi26-3-3 type austenitic steels, after hot deformation as well as after cold rolling, were evaluated in 3.5% NaCl solution using potentiodynamic polarization tests. A type of nonmetallic inclusions and their pitting corrosion behaviour were investigated. Additionally, the effect of cold deformation on the corrosion resistance of high-Mn steels was studied. The SEM micrographs revealed that corrosion damage formed in both investigated steels is characterized by various shapes and an irregular distribution at the metallic matrix, independently on the steel state (thermomechanically treated or cold worked. Corrosion pits are generated both in grain interiors, grain boundaries and along the deformation bands. Moreover, corrosion damage is stronger in cold deformed steels in comparison to the thermomechanically treated specimens. EDS analysis revealed that corrosion pits preferentially nucleated on MnS and AlN inclusions or complex oxysulphides. The morphology of corrosion damage in 3.5% NaCl supports the data registered in potentiodynamic tests.

Synthesis of Mn-intercalated layered titanate by exfoliation–flocculation approach and its efficient photocatalytic activity under visible–light

International Nuclear Information System (INIS)

Fu, Jie; Tian, Yanlong; Chang, Binbin; Li, Gengnan; Xi, Fengna; Dong, Xiaoping

2012-01-01

A novel Mn-intercalated layered titanate as highly active photocatalyst in visible-light region has been synthesized via a convenient and efficient exfoliation–flocculation approach with divalent Mn ions and monolayer titanate nanosheets. The 0.91 nm interlayer spacing of obtained photocatalyst is in accordance with the sum of the thickness of titanate nanosheet and the diameter of Mn ions. The yellow photocatalyst shows a spectral response in visible-light region and the calculated band gap is 2.59 eV. The photocatalytic performance of this material was evaluated by degradation and mineralization of an aqueous dye methylene blue under visible-light irradiation, and an enhanced photocatalytic activity in comparison with protonated titanate as well as the P25 TiO 2 and N-doped TiO 2 was obtained. Additionally, the layered structure is retained, no dye ions intercalating occurs during the photocatalysis process, and a ∼90% photocatalytic activity can be remained after reusing 3 cycles. - Graphical abstract: Mn-intercalated layered titanate as a novel and efficient visible-light harvesting photocatalyst was synthesized via a convenient and efficient exfoliation–flocculation approach in a mild condition. Highlights: ► Mn-intercalated titanate has been prepared by exfoliation–flocculation approach. ► The as-prepared catalyst shows spectral response in the visible-light region. ► Heat treatment at certain temperature enables formation of Mn-doped TiO 2 . ► Dye can be degradated effectively by the catalyst under visible light irradiation.

Gaseous Phase and Electrochemical Hydrogen Storage Properties of Ti50Zr1Ni44X5 (X = Ni, Cr, Mn, Fe, Co, or Cu for Nickel Metal Hydride Battery Applications

Directory of Open Access Journals (Sweden)

Jean Nei

2016-07-01

Full Text Available Structural, gaseous phase hydrogen storage, and electrochemical properties of a series of the Ti50Zr1Ni44X5 (X = Ni, Cr, Mn, Fe, Co, or Cu metal hydride alloys were studied. X-ray diffraction (XRD and scanning electron microscopy (SEM revealed the multi-phase nature of all alloys, which were composed of a stoichiometric TiNi matrix, a hyperstoichiometric TiNi minor phase, and a Ti2Ni secondary phase. Improvement in synergetic effects between the main TiNi and secondary Ti2Ni phases, determined by the amount of distorted lattice region in TiNi near Ti2Ni, was accomplished by the substitution of an element with a higher work function, which consequently causes a dramatic increase in gaseous phase hydrogen storage capacity compared to the Ti50Zr1Ni49 base alloy. Capacity performance is further enhanced in the electrochemical environment, especially in the cases of the Ti50Zr1Ni49 base alloy and Ti50Zr1Ni44Co5 alloy. Although the TiNi-based alloys in the current study show poorer high-rate performances compared to the commonly used AB5, AB2, and A2B7 alloys, they have adequate capacity performances and also excel in terms of cost and cycle stability. Among the alloys investigated, the Ti50Zr1Ni44Fe5 alloy demonstrated the best balance among capacity (394 mAh·g−1, high-rate performance, activation, and cycle stability and is recommended for follow-up full-cell testing and as the base composition for future formula optimization. A review of previous research works regarding the TiNi metal hydride alloys is also included.

Structural characteristics and sorption properties of lithium-selective composite materials based on TiO2 and MnO2

Science.gov (United States)

Chaban, M. O.; Rozhdestvenska, L. M.; Palchyk, O. V.; Dzyazko, Y. S.; Dzyazko, O. G.

2018-04-01

A number of nanomaterials containing titanium dioxide and manganese dioxide were synthesized. The effect of synthesis conditions on structural and sorption characteristics for the selective extraction of lithium ions from solutions was studied. The ion-exchange materials were investigated with the methods of electron microscopy, thermogravimetric and X-ray analyses. During thermal synthesis phases of lithium manganese titanium spinel and TiO2 are being formed. Replacing a part of manganese with titanium ions leads to a decrease in the dissolution of Mn and to an increase in chemical stability. Composites with optimal values of selectivity and sorption rates were used to remove lithium ions from solutions with high salt background. The recovery degree of lithium ions under dynamic conditions reached 99%, the highest sorption capacity was found at pH 10.

Correlating interfacial octahedral rotations with magnetism in (LaMnO3+δ)N/(SrTiO3)N superlattices.

Science.gov (United States)

Zhai, Xiaofang; Cheng, Long; Liu, Yang; Schlepütz, Christian M; Dong, Shuai; Li, Hui; Zhang, Xiaoqiang; Chu, Shengqi; Zheng, Lirong; Zhang, Jing; Zhao, Aidi; Hong, Hawoong; Bhattacharya, Anand; Eckstein, James N; Zeng, Changgan

2014-07-09

Lattice distortion due to oxygen octahedral rotations have a significant role in mediating the magnetism in oxides, and recently attracts a lot of interests in the study of complex oxides interface. However, the direct experimental evidence for the interrelation between octahedral rotation and magnetism at interface is scarce. Here we demonstrate that interfacial octahedral rotation are closely linked to the strongly modified ferromagnetism in (LaMnO3+δ)N/(SrTiO3)N superlattices. The maximized ferromagnetic moment in the N=6 superlattice is accompanied by a metastable structure (space group Imcm) featuring minimal octahedral rotations (a(-)a(-)c(-), α~4.2°, γ~0.5°). Quenched ferromagnetism for Nmagnetism. Our study demonstrates that engineering superlattices with controllable interfacial structures can be a feasible new route in realizing functional magnetic materials.

Magnetocrystalline anisotropy and magnetic domain structure of ErFe{sub 11}Ti and HoFe{sub 11}Ti compounds

Energy Technology Data Exchange (ETDEWEB)

Pastushenkov, Yury G. [Physics Department of Tver State University, 17000 Tver (Russian Federation); Skokov, Konstantin P. [Physics Department of Tver State University, 17000 Tver (Russian Federation); Skourski, Yury [Leibniz-Institute for Solid State and Material Research, 01171 Dresden (Germany); Lebedeva, Ludmila [Physics Department of Tver State University, 17000 Tver (Russian Federation); Ivanova, Tatyana [Physics Department of Moscow Stae University, 119889 Moscow (Russian Federation); Grushichev, Anton [Physics Department of Tver State University, 17000 Tver (Russian Federation)]. E-mail: yupast@tversu.ru; Mueller, Karl-Hartmut [Leibniz-Institute for Solid State and Material Research, 01171 Dresden (Germany)

2006-05-15

Tetragonal ThMn{sub 12}-type single crystalline ErFe{sub 11}Ti and HoFe{sub 11}Ti samples have been investigated by magnetization measurements and by observations of the magnetic domain structure at various temperatures between 10 and 300K. The magnetic structure of ErFe{sub 11}Ti changes from room temperature 'easy axis' (c-axis) type to conical at spin-reorientation temperature T{sub SR}=50K. The HoFe{sub 11}Ti has a metastable anisotropy energy minimum in the a-direction at T<40K. It leads to a first-order magnetization process detected by magnetization measurements along the a-axis in this temperature region.

Strain and electric field mediated manipulation of magnetism in La_(_1_-_x_)Sr_xMnO_3/BaTiO_3 heterostructures

International Nuclear Information System (INIS)

Schmitz, Markus

2016-01-01

Heterostructures of ferromagnetic La_1_-_xSr_xMnO_3 (LSMO) and ferroelectric BaTiO_3 (BTO) were produced and investigated for their structural and magnetic properties. The combination of these ferroic properties can lead to an artificial multiferroic. Special emphasis was given to the manipulation of magnetic properties by applying electric fields. A magneto-electric coupling could be observed in the heterostructures under investigation. Epitaxial LSMO thin films were grown on BTO substrates using a state-of-the-art oxide molecular beam epitaxy (OMBE) and a high oxygen sputtering system (HOPSS). Stoichiometric La_1_-_xSr_xMnO_3 films with doping levels of x=0.5 and x=0.3 were produced. The film quality in terms of roughness and crystalline structure was confirmed by X-ray scattering methods. The presence of structural domains in the BaTiO_3 single crystal substrate, whose proportion could be altered due to the application of electric fields, was shown by X-ray diffraction. Tensile strain is induced into the epitaxial La_1_-_xSr_xMnO_3 films in the whole temperature range under investigation. The magnetization of LSMO alteres by the variation of strain induced into the film, generated by the different structural phases of single crystal BaTiO_3 substrates. The magnetization shows sharp steps at the structural phase transition temperatures of BTO. The evaluation of magnetic hysteresis loops reveals a change of the magnetic anisotropy of LSMO for each structural phase of BTO, but also within the orthorhombic phase. Special focus was given to the manipulation of magnetic properties by the application of electric fields. A newly established measurement option was used to determine the magnetic response to an applied electric field as a function of temperature and magnetic field. The electrically induced modification of the magnetization is profound near the structural phase transition temperatures. Electrical hysteresis loops give a detailed view on the influence of the

Anisotropic magnetoresistance and spin polarization of La0.7Sr0.3MnO3/SrTiO3 superlattices

International Nuclear Information System (INIS)

Wang, L.M.; Guo, C.-C.

2005-01-01

The crystalline structure, anisotropic magnetoresistance (AMR), and magnetization of La 0.7 Sr 0.3 MnO 3 /SrTiO 3 (LSMO/STO) superlattices grown by a rf sputtering system are systematically analyzed to study the spin polarization of manganite at interfaces. The presence of positive low-temperature AMR in LSMO/STO superlattices implies that two bands of majority and minority character contribute to the transport properties, leading to a reduced spin polarization. Furthermore, the magnetization of superlattices follows the T 3/2 law and decays more quickly as the thickness ratio d STO /d LSMO increases, corresponding to a reduced exchange coupling. The results clearly show that the spin polarization is strongly correlated with the influence of interface-induced strain on the structure

Rate-dependent response of superelastic Cu–Al–Mn alloy rods to tensile cyclic loads

International Nuclear Information System (INIS)

Araki, Yoshikazu; Maekawa, Nao; Omori, Toshihiro; Sutou, Yuji; Kainuma, Ryosuke; Ishida, Kiyohito

2012-01-01

We report the results of tensile cyclic loading tests conducted to examine the dependence of constitutive relations for superelastic Cu–Al–Mn alloy rods on loading rates. Recently, Cu–Al–Mn alloy rods with diameters up to 8 mm have been developed by the authors, and it has been demonstrated that these rods have excellent superelastic strains of more than 8%, which is comparable to Ni–Ti alloys and far superior to other Cu-based alloys. No information is available, however, on the rate dependence of constitutive relations for Cu–Al–Mn alloys. In this study, we prepare two Cu–Al–Mn alloy rod specimens, whose lengths and diameters are 150 mm and 8 mm, respectively. Their stress–strain relations are examined under the loading frequencies of 0.001, 0.5, and 1 Hz with constant strain amplitude of 4.5%. It was found from the tests that the maximum stress increase in Cu–Al–Mn alloys due to higher loading rate was less than 5%. Thermo-mechanical analysis predicts that stress increase in Cu–Al–Mn alloys is about 1/4 of that in Ni–Ti alloys, which agrees reasonably well with the experimental observations. Such low stress increase is highly desirable in the design of seismic devices such as dampers and isolators. (fast track communication)

Structural, spectroscopic, and dielectric characterizations of Mn-doped 0.67BiFeO3-0.33BaTiO3 multiferroic ceramics

KAUST Repository

Hang, Qiming

2013-09-07

0.67BiFeO3-0.33BaTiO3 multiferroic ceramics doped with x mol% MnO2 (x = 2–10) were synthesized by solid-state reaction. The formation of a perovskite phase with rhombohedral symmetry was confirmed by X-ray diffraction (XRD). The average grain sizes were reduced from 0.80 μm to 0.50 μm as increasing the Mn-doped levels. Single crystalline nature of the grains was revealed by high-resolution transmission electron microscopy (HRTEM) images and electron diffraction patterns. Polar nano-sized ferroelectric domains with an average size of 9 nm randomly distributed in the ceramic samples were revealed by TEM images. Ferroelectric domain lamellae (71° ferroelectric domains) with an average width of 5 nm were also observed. Vibrational modes were examined by Raman spectra, where only four Raman peaks at 272 cm−1 (E-4 mode), 496 cm−1 (A 1-4 mode), 639 cm−1, and 1338 cm−1 were observed. The blue shifts in the E-4 and A 1-4 Raman mode frequencies were interpreted by a spring oscillator model. The dieletric constants of the present ceramics as a function of the Mn-doped levels exhibited a V-typed curve. They were in the range of 350–700 measured at 103 Hz, and the corresponding dielectric losses were in range of 0.43–0.96, approaching to 0.09 at 106 Hz.

Structural, spectroscopic, and dielectric characterizations of Mn-doped 0.67BiFeO3-0.33BaTiO3 multiferroic ceramics

KAUST Repository

Hang, Qiming; Zhou, Wenke; Zhu, Xinhua; Zhu, Jianmin; Liu, Zhiguo; Al-Kassab, Talaat

2013-01-01

0.67BiFeO3-0.33BaTiO3 multiferroic ceramics doped with x mol% MnO2 (x = 2–10) were synthesized by solid-state reaction. The formation of a perovskite phase with rhombohedral symmetry was confirmed by X-ray diffraction (XRD). The average grain sizes were reduced from 0.80 μm to 0.50 μm as increasing the Mn-doped levels. Single crystalline nature of the grains was revealed by high-resolution transmission electron microscopy (HRTEM) images and electron diffraction patterns. Polar nano-sized ferroelectric domains with an average size of 9 nm randomly distributed in the ceramic samples were revealed by TEM images. Ferroelectric domain lamellae (71° ferroelectric domains) with an average width of 5 nm were also observed. Vibrational modes were examined by Raman spectra, where only four Raman peaks at 272 cm−1 (E-4 mode), 496 cm−1 (A 1-4 mode), 639 cm−1, and 1338 cm−1 were observed. The blue shifts in the E-4 and A 1-4 Raman mode frequencies were interpreted by a spring oscillator model. The dieletric constants of the present ceramics as a function of the Mn-doped levels exhibited a V-typed curve. They were in the range of 350–700 measured at 103 Hz, and the corresponding dielectric losses were in range of 0.43–0.96, approaching to 0.09 at 106 Hz.

Effect of alloying elements on the shape memory properties of ductile Cu-Al-Mn alloys

International Nuclear Information System (INIS)

Sutou, Y.; Kainuma, R.; Ishida, K.

1999-01-01

The effect of alloying elements on the M s temperature, ductility and the shape memory properties of Cu-Al-Mn ductile shape memory (SM) alloys was investigated by differential scanning calorimetry, cold-rolling and tensile test techniques. It was found that the addition of Au, Si and Zn to the Cu 73 -Al 17 -Mn 10 alloy stabilized the martensite (6M) phase increasing the M s temperature, while the addition of Ag, Co, Cr, Fe, Ni, Sn and Ti decreased the stability of the martensite phase, decreasing the M s temperature. The SM properties were improved by the addition of Co, Ni, Cr and Ti. (orig.)

Structural and electromagnetic characteristics of perovskites in La1–c–xSrc+xMn1–xMe4+xO3 systems (Me=Ge, Ti

Directory of Open Access Journals (Sweden)

Karpasyuk V.

2013-01-01

Full Text Available Experimental data are shown for the influence of substituting quadrivalent ions on the concentration phase transitions “rhombohedral-orthorhombic structure” and “semiconductor-metal” in ceramic manganites of specifically designed system La3+1–c–xSr2+c+xMn3+1–c–xMn4+cMe4+xO3 (c=0.15, 0.17, 0.19; 0.025≤x≤0.125. Regularities in the concentration dependences of unit cell volume, saturation magnetization, Curie point, and resistivity were established. Ge-substituted manganites had essentially higher values of magnetization and Curie temperature than analogous compositions with Ti. The approach to the interpretation of experimental results is discussed in terms of electron configurations and ionic radii of substituents taking into account oxygen nonstoichiometry and cation vacancies.

High temperature superconductivity in Zn and Mn substituted (Tl,Cr)Sr2CaCu2O7

International Nuclear Information System (INIS)

Lo, S.V.; Abd Shukor, R.

1999-01-01

Samples with nominal starting composition (TICr 0 .15)Sr 2 (Ca 1-x M x )Cu 2 O 7 (TI-1212) for x=0 - 0.7 with M= Zn and Mn have been prepared and investigated by powder X-ray diffraction (XRD) and electrical resistance measurements. All sample showed a mixed phase of 1212 and 1201. Dominant 1212-phase was observed for x=0.0-0.5 and x=0.0-0.4, for Zn and Mn series, respectively. The superconducting transition temperature was suppressed when Zn and Mn are substituted at the Ca site. For the Zn series the normal state behavior is metallic throughout the doping range. For the Mn series the normal state behavior is metallic for 0.1≤x≥0.3 and semiconducting like x>0.3. The suppression of T c and formation of the TI-1212 phase are discussed in terms of the ionic radius and valence state of the substituted elements. (author)

Crystallographic and electronic structure of the Ca{sub 2}TiMnO{sub 6} double perovskite

Energy Technology Data Exchange (ETDEWEB)

López, J.P. Garzón [Grupo de Física de Nuevos Materiales, Departamento de Física, Universidad Nacional de Colombia, AA 5997 Bogotá DC (Colombia); Grupo de Estudios de Materiales – GEMA, Departamento de Física, Universidad Nacional de Colombia, AA 5997 Bogotá DC (Colombia); Cardona, R. [Grupo de Estudios de Materiales – GEMA, Departamento de Física, Universidad Nacional de Colombia, AA 5997 Bogotá DC (Colombia); Santos, A. Sarmiento [Grupo de Superficies, Electroquímica y Corrosión, Universidad Pedagógica y Tecnológica de Colombia, Tunja (Colombia); Téllez, D.A. Landínez [Grupo de Física de Nuevos Materiales, Departamento de Física, Universidad Nacional de Colombia, AA 5997 Bogotá DC (Colombia); Roa-Rojas, J., E-mail: jroar@unal.edu.co [Grupo de Física de Nuevos Materiales, Departamento de Física, Universidad Nacional de Colombia, AA 5997 Bogotá DC (Colombia)

2014-12-15

In this work, we report synthesis and crystalline structure study of the Ca{sub 2}TiMnO{sub 6} complex perovskite, by X-ray diffraction experiments and through the application of the Rietveld refinement using the GSAS code. Results revealed the crystallization of the system in a tetragonal perovskite with the characteristic structure given by I4/m (#87) space group and lattice parameters a=5.339(4) Å and c=7.736(6) Å. Ab initio calculations of density of states (DOS) and electronic structure were carried out for this perovskite-like system, by the Density Functional Theory (DFT) and using the Full-potential Linearized Augmented Plane Waves (FP-LAPW) method. The exchange-correlation potential was treated using the Generalized Gradient Approximation (GGA). All calculations were carried-out using spin polarization. For the up spin orientation the compound has a semiconducting behavior and for down spin polarization it behaves like a conductor. The calculated effective magnetic moment in cell was 4.02 μ{sub B}, which is close to the expected value calculated from Hund's rules.

Structure and cation distribution of (Mn0.5Zn0.5)Fe2O4 thin films on SrTiO3(001)

Science.gov (United States)

Welke, M.; Brachwitz, K.; Lorenz, M.; Grundmann, M.; Schindler, K.-M.; Chassé, A.; Denecke, R.

2017-06-01

A comprehensive study on growth of ferrimagnetic manganese zinc ferrite (Mn0.5Zn0.5Fe2O4) films on single crystalline strontium titanate(001) (SrTiO3) substrates was carried out. Under the optimized conditions, a thin film with a layer thickness of 200 nm was deposited, and the structural properties were investigated. Contrary to data published in literature, no buffer layer was necessary to achieve epitaxial growth of a poorly lattice-matched layer. This was confirmed for Mn0.5Zn0.5Fe2O4(001) on SrTiO3(001) by x-ray diffraction and the adjoined phi scans, which also revealed a lattice compression of 1.2% of the manganese zinc ferrite film in the out-of-plane direction. Using x-ray photoelectron spectroscopy, the near surface stoichiometry of the film could be shown to agree with the intended one within the uncertainty of the method. X-ray absorption spectroscopy showed an electronic structure close to that published for bulk samples. Additional x-ray magnetic circular dichroism investigations were performed to answer detailed structural questions by a comparison of experimental data with the calculated ones. The calculations took into account ion sites (tetrahedral vs. octahedral coordination) as well as the charge of Fe ions (Fe2+ vs. Fe3+). Contrary to the expectation for a perfect normal spinel that only Fe3+ ions are present in octahedral sites, hints regarding the presence of additional Fe2+ in octahedral sites as well as Fe3+ ions in tetrahedral sites have been obtained. Altogether, the layer could be shown to be mostly in a normal spinel configuration.

Microstructure evolution and phase transition in La/Mn doped barium titanate ceramics

Directory of Open Access Journals (Sweden)

Vesna Paunović

2010-12-01

Full Text Available La/Mn codoped BaTiO3 with different La2O3 content, ranging from 0.1 to 5.0 at% La, was investigated regarding their microstructural and dielectric characteristics. The content of 0.05 at% Mn was constant in all investigated samples. The samples were sintered at 1320°C and 1350°C for two hours. Microstructural studies were done using SEM and EDS analysis. The fine-grained microstructure was obtained even for low content of La. The appearance of secondary abnormal grains with serrated features along grain boundaries was observed in 1.0 at% La-BaTiO3 sintered at 1350°C. Nearly flat permittivity-temperature response was obtained in specimens with 2.0 and 5.0 at% La. Using the modified Curie-Weiss law a critical exponent γ and C’were calculated. The obtained values of γ pointed out the diffuse phase transformation in heavily doped BaTiO3 and great departure from the Curie-Weiss law for low doped ceramics.

FTIR and Raman Study of the LixTiyMn1-yO2 (y = 0, 0.11) Cathodes in Methylpropyl Pyrrolidinium Bis(fluoro-sulfonyl)imide, LiTFSI Electrolyte

Energy Technology Data Exchange (ETDEWEB)

Hardwick, L.J.; Lucas, I.T.; Doeff, M.M.; Kostecki, R.; Saint, J.A.

2009-02-02

This work demonstrates the protective effect of partial titanium substitution in Li{sub x}Ti{sub 0.11}Mn{sub 0.89}O{sub 2} against surface decomposition in room-temperature ionic liquid (RTILs) cells. Raman microscopy and reflectance Fourier transform IR (FTIR) spectroscopy were used to analyze electrodes recovered from cycled Li/Li{sub x}Ti{sub y}Mn{sub 1-y}O{sub 2} (y=0, 0.11) cells containing the 0.5 mol/kg LiTFSI in P{sub 13}FSI RTIL electrolyte. [TFSI=bis(trifluoromethanesulfonyl)imide.] Raman and FTIR spectra of cycled Li{sub x}MnO{sub 2} cathodes showed many distinct bands that can be attributed to both the electrolyte and electrode decomposition products. The thickness of the amorphous porous layer on the Li{sub x}MnO{sub 2} cathode increased during cycling. The surface degradation of Li{sub x}MnO{sub 2} and precipitation of electrolyte decomposition products contributed to the film growth. Improved cycling behavior was observed in cells containing Li{sub x}Ti{sub 0.11}Mn{sub 0.89}O{sub 2}, yet Raman spectroscopy also showed possible surface degradation. The FTIR spectra of cycled Li{sub x}MnO{sub 2} and Li{sub x}Ti{sub 0.11}Mn{sub 0.89}O{sub 2} cathodes displayed bands characteristic for LiSO{sub 3}CF{sub 3} and Li{sub 2}NSO{sub 2}CF{sub 3}, which originate from the reaction of the TFSI anion with traces of water present in the cell.

Monte Carlo and Ab-initio calculation of TM (Ti, V, Cr, Mn, Fe, Co, Ni) doped MgH{sub 2} hydride: GGA and SIC approximation

Energy Technology Data Exchange (ETDEWEB)

Salmani, E., E-mail: elmehdisalmani@gmail.com [LMPHE (URAC12), Faculty of Sciences, Mohammed V University in Rabat (Morocco); Laghrissi, A.; Lamouri, R. [LMPHE (URAC12), Faculty of Sciences, Mohammed V University in Rabat (Morocco); Benchafia, E. [Department of Materials Science and Engineering, New Jersey Institute of Technology, Newark, NJ 07102 (United States); Ez-Zahraouy, H. [LMPHE (URAC12), Faculty of Sciences, Mohammed V University in Rabat (Morocco); Benyoussef, A. [Institute for Nanomaterials and Nanotechnologies, MAScIR, Rabat (Morocco)

2017-02-15

MgH{sub 2}: TM (TM: V, Cr, Mn, Fe, Co, Ni) based dilute magnetic semiconductors (DMS) are investigated using first principle calculations. Our results show that the ferromagnetic state is stable when TM introduces magnetic moments as well as intrinsic carriers in TM: Co, V, Cr, Ti; Mg{sub 0.95}TM{sub 0.05}H{sub 2}. Some of the DMS Ferro magnets under study exhibit a half-metallic behavior, which make them suitable for spintronic applications. The double exchange is shown to be the underlying mechanism responsible for the magnetism of such materials. The exchange interactions obtained from first principle calculations and used in a classical Ising model by a Monte Carlo approach resulted in ferromagnetic states with Curie temperatures within the ambient conditions. - Highlights: • The half-metallic aspect was proven to take place for Ti, Cr, Co and Ni. • The TM impurities are shown to introduce the magnetic moment that makes MgH{sub 2} good candidates for spintronic applications.

Generating MnO2 nanoparticles using simulated amorphization and recrystallization

CSIR Research Space (South Africa)

Sayle, TXT

2005-09-21

Full Text Available . The resulting MnO2 nanoparticle is about 8 nm in diameter, conforms to the pyrolusite structure (isostructural with rutile TiO2, comprising 1 x 1 octahedra) is heavily twinned and comprises a wealth of isolated and clustered point defects such as cation...

The characteristics of precipitates in 18% Cr/30% Ni cast steel with additions of Nb and Ti

International Nuclear Information System (INIS)

Piekarski, B.

1995-01-01

The microstructure of austenitic cast steel with approx. 0.3%C, 4.37%Si, 0.69%Mn, 17.8%Cr, 29.3%Ni, 1.47%Nb and 1.07%Ti have been examined after ageing at 900 C for 300 h. There was found five precipitates: M 23 C 6 , MnS, Ni 3 Fe, (Ti,Nb)C and an intermetallic Ni-Nb-S phase. Ni, Nb, Si-rich precipitate could have been formed in as cast condition. (author)

Ti-44, Al-26 and Mn-53 samples for nuclear astrophysics: The needs, the possibilities and the sources

CERN Document Server

Dressler, R; Bemmerer, D; Bunka, M; Dai, Y; Lederer, C; Fallis, J; Murphy, A StJ; Pignatari, M; Schumann, D; Stora, T; Stowasser, T; Thielemann, F K; Woods, P J

2012-01-01

Exploration of the physics involved in the production of cosmogenic radionuclides requires experiments using the same rare, radioactive nuclei in sufficient quantities. For this work, such exotic radionuclides have been extracted from previously proton-irradiated stainless steel samples using wet chemistry separation techniques. The irradiated construction material has arisen from an extended material research programme at the Paul Scherrer Institute, called STIP (SINQ Target Irradiation Program), where several thousand samples of different materials were irradiated with protons and neutrons of energies up to 570 MeV. In total, 8 Oe 10(17) atoms of (44)Ti, -10(16) atoms of (26)Al and -10(19) atoms of (53)Mn are available from selected samples. These materials may now be used to produce targets or radioactive beams for nuclear reaction studies with protons, neutrons and alpha-particles. The work is part of the ERAWAST initiative (Exotic Radionuclides from Accelerator Waste for Science and Technology), aimed at...

The effect of synthesis parameters on the lithium storage performance of LiMnPO4/C

International Nuclear Information System (INIS)

Ramar, V.; Saravanan, K.; Gajjela, S.R.; Hariharan, S.; Balaya, P.

2013-01-01

Highlights: • An architecture featuring carbon coated, interconnected nano-grains was constructed with mesopores for LiMnPO 4 /C cathodes. • Mesoporous LiMnPO 4 /C delivers 140 mAh g −1 at 0.05 C, one of the best storage performances in galvanostatic charge/discharge mode. • Interdependence of storage performance on carbon, milling time, grain size, surface area, pore size and pore volume is elucidated. • Feasible full cell operation with Li 4 Ti 5 O 12 /C anode. -- Abstract: An architecture featuring carbon coated, interconnected nano-grains constructed with mesopores is developed for LiMnPO 4 cathode material. This architecture facilitates enhanced lithium ionic and electronic transports; favours improved lithium storage performance. Mesoporous LiMnPO 4 /C electrode delivers discharge capacity of 140 mAh g −1 at 0.05 C using galvanostatic cycling mode. This best electrochemical response of LiMnPO 4 /C at constant current mode is complemented by diffusion studies using cyclic voltammetry and impedance spectroscopy. Further, the interdependence of lithium storage performance on carbon content, milling time (2, 4, 6 and 10 h), grain size and porous characteristics (surface area, pore size and pore volume) is also discussed. Finally, the feasibility of LiMnPO 4 /C cathode is evaluated against Li 4 Ti 5 O 12 /C anode in a full cell

Cavitation erosion of Ti-Ni shape memory alloy deposited coatings and Fe base shape memory alloy solid

International Nuclear Information System (INIS)

Hattori, Shuji; Fujisawa, Seiji; Owa, Tomonobu

2007-01-01

In this study, cavitation erosion tests were carried out by using thermal spraying and deposition of Ti-Ni shape memory alloy for the surface coating. The results show the test speciment of Ti-Ni thermal spraying has many initial defects, so that the erosion resistance is very low. The erosion resistance of Ti-Ni deposit is about 5-10 times higher than that of SUS 304, thus erosion resistance of Ti-Ni deposit is better than that of Ti-Ni thermal spraying. The cavitation erosion tests were carried out by using Fe-Mn-Si with shape memory and gunmetal with low elastic modulus. The erosion resistance of Fe-Mn-Si shape memory alloy solid is about 9 times higher than that of SUS 304. The erosion resistance of gunmetal is almost the same as SUS 304, because the test specimen of gunmetal has many small defects on the original surface. (author)

Perovskite-based heterostructures integrating ferromagnetic-insulating La0.1Bi0.9MnO3

Science.gov (United States)

Gajek, M.; Bibes, M.; Barthélémy, A.; Varela, M.; Fontcuberta, J.

2005-05-01

We report on the growth of thin films and heterostructures of the ferromagnetic-insulating perovskite La0.1Bi0.9MnO3. We show that the La0.1Bi0.9MnO3 perovskite grows single phased, epitaxially, and with a single out-of-plane orientation either on SrTiO3 substrates or onto strained La2/3Sr1/3MnO3 and SrRuO3 ferromagnetic-metallic buffer layers. We discuss the magnetic properties of the La0.1Bi0.9MnO3 films and heterostructures in view of their possible potential as magnetoelectric or spin-dependent tunneling devices.

Electrochemically conductive treatment of TiO2 nanotube arrays in AlCl3 aqueous solution for supercapacitors

Science.gov (United States)

Zhong, Wenjie; Sang, Shangbin; Liu, Yingying; Wu, Qiumei; Liu, Kaiyu; Liu, Hongtao

2015-10-01

Highly ordered TiO2 nanotube arrays (NTAs) with excellent stability and large specific surface area make them competitive using as supercapacitor materials. Improving the conductivity of TiO2 is of great concern for the construction of high-performance supercapacitors. In this work, we developed a novel approach to improve the performance of TiO2 materials, involving the fabrication of Al-doped TiO2 NTAs by a simple electrochemical cathodic polarization treatment in AlCl3 aqueous solution. The prepared Al-doped TiO2 NTAs exhibited excellent electrochemical performances, attributing to the remarkably improved electrical conductivity (i.e., from approx. 10 kΩ to 20 Ω). Further analysis showed that Al3+ ions rather than H+ protons doped into TiO2 lattice cause this high conductivity. A MnO2/Al-TiO2 composite was evaluated by cyclic voltammetry, and achieved the specific capacitance of 544 F g-1, and the Ragone plot of the sample showed a high power density but less reduction of energy density. These results indicate that the MnO2/Al-TiO2 NTAs sample could be served as a promising electrode material for high -performance supercapacitors.

Influence of rare-earth additives (La, Sm and Dy on the microstructure and dielectric properties of doped BaTiO3 ceramics

Directory of Open Access Journals (Sweden)

Paunović Vesna

2010-01-01

Full Text Available A series of La/Mn, Sm/Mn and Dy/Mn codoped BaTiO3 samples were prepared by the conventional solid state procedure with dopant concentrations ranging from 0.1 up to 2.0 at%. The specimens were sintered at 1320°C and 1350°C in an air atmosphere for two hours. The low doped samples demonstrated a mainly uniform and homogeneous microstructure with average grain sizes ranging from 0.3 μm to 5.0 μm. The appearance of secondary abnormal grains in the fine grain matrix and core-shell structure were observed in highly doped La/BaTiO3 and Dy/BaTiO3 sintered at 1350°C. The low doped samples, sintered at 1350°C, display a high value of dielectric permittivity at room temperature, 6800 for Sm/BaTiO3, 5900 for Dy/BaTiO3 and 3100 for La/BaTiO3. A nearly flat permittivity-response was obtained in specimens with 2.0 at% additive content. Using a modified Curie-Weiss law the Curie-like constant C⁄ and a critical exponent γ were calculated. The obtained values of γ pointed out the diffuse phase transformation in heavily doped BaTiO3 samples.

From Serendipity to Rational Design: Tuning the Blue Trigonal Bipyramidal Mn3+ Chromophore to Violet and Purple through Application of Chemical Pressure.

Science.gov (United States)

Li, Jun; Lorger, Simon; Stalick, Judith K; Sleight, Arthur W; Subramanian, M A

2016-10-03

We recently reported that an allowed d-d transition of trigonal bipyramidal (TBP) Mn 3+ is responsible for the bright blue color in the YIn 1-x Mn x O 3 solid solution. The crystal field splitting between a'(d z 2 ) and e'(d x 2 -y 2 , d xy ) energy levels is very sensitive to the apical Mn-O distance. We therefore applied chemical pressure to compress the apical Mn-O distance in YIn 1-x Mn x O 3 , move the allowed d-d transition to higher energy, and thereby tune the color from blue to violet/purple. This was accomplished by substituting smaller cations such as Ti 4+ /Zn 2+ and Al 3+ onto the TBP In/Mn site, which yielded novel violet/purple phases. The general formula is YIn 1-x-2y-z Mn x Ti y Zn y Al z O 3 (x = 0.005-0.2, y = 0.1-0.4, and z ≤ 0.1), where the color darkens with the increasing amount of Mn. Higher y or small additions of Al provide a more reddish hue to the resulting purple colors. Substituting other rare earth cations for Y has little impact on color. Crystal structure analysis by neutron powder diffraction confirms a shorter apical Mn-O distance compared with that in the blue YIn 1-x Mn x O 3 . Magnetic susceptibility measurements verify the 3+ oxidation state for Mn. Diffuse reflection spectra were obtained over the wavelength region 200-2500 nm. All samples show excellent near-infrared reflectance comparable to that of commercial TiO 2 , making them ideal for cool pigment applications such as energy efficient roofs of buildings and cars where reducing solar heat to save energy is desired. In a comparison with commercial purple pigments, such as Co 3 (PO 4 ) 2 , our pigments are much more thermally stable and chemically inert, and are neither toxic nor carcinogenic.

The influence of bismuth oxide doping on the rechargeability of aqueous cells using MnO2 cathode and LiOH electrolyte

International Nuclear Information System (INIS)

Minakshi, Manickam; Mitchell, David R.G.

2008-01-01

Bi-doped manganese dioxide (MnO 2 ) has been prepared from γ-MnO 2 by physical admixture of bismuth oxide (Bi 2 O 3 ). The doping improved the cycling ability of the aqueous cell. These results are discussed and compared with the electrochemical behavior of bismuth-free MnO 2 . Batteries using the traditional potassium hydroxide (KOH) electrolyte are non-rechargeable. However, with lithium hydroxide (LiOH) as an electrolyte, the cell becomes rechargeable. Furthermore, the incorporation of bismuth into MnO 2 in the LiOH cell was found to result in significantly longer cycle life, compared with cells using undoped MnO 2 . The Bi-doped cell exhibited a greater capacity after 100 discharge cycles, than the undoped cell after just 40 cycles. X-ray diffraction and the microscopic analysis suggest that the presence of Bi 3+ ions reduces the magnitude of structural changes occurring in MnO 2 during cycling. Comparison with additives assessed in our previous studies (titanium disulfide (TiS 2 ); titanium boride (TiB 2 )) shows that the best rechargeability behavior is obtained for the current Bi-doped MnO 2 . As the size of Bi 3+ ions (0.96 A) is much larger than Mn 3+ (0.73 A) or Mn 2+ (0.67 A) they have effectively prevented the formation of non-rechargeable products

Dynamic globularization of a-phase in Ti6Al4V alloy during hot compression

CSIR Research Space (South Africa)

Mutombo, K

2013-12-01

Full Text Available composition dependence of the martensite start temperature (Ms) has been done for Ti-Fe, Ti-Cr, Ti-Mo, Ti-V, Ti-Nb, Ti-Zr and Ti-Al alloys [1], [2]. The beneficial effect on the formation of hexagonal-structured martensite (α′) of Al, Mn, Cr, Sn and Fe... alloying elements, has been discussed by Lin et al [4]. However, the formation of the orthorhombic-structured martensite (α′′) which is favoured by elements such as Nb, Mo, Zr, W and V (strong β stabilizers) or H (a strong β stabilizer), has been reported...

Integrated removal of NO and mercury from coal combustion flue gas using manganese oxides supported on TiO2.

Science.gov (United States)

Zhang, Shibo; Zhao, Yongchun; Wang, Zonghua; Zhang, Junying; Wang, Lulu; Zheng, Chuguang

2017-03-01

A catalyst composed of manganese oxides supported on titania (MnO x /TiO 2 ) synthesized by a sol-gel method was selected to remove nitric oxide and mercury jointly at a relatively low temperature in simulated flue gas from coal-fired power plants. The physico-chemical characteristics of catalysts were investigated by X-ray fluorescence (XRF), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) analyses, etc. The effects of Mn loading, reaction temperature and individual flue gas components on denitration and Hg 0 removal were examined. The results indicated that the optimal Mn/Ti molar ratio was 0.8 and the best working temperature was 240°C for NO conversion. O 2 and a proper ratio of [NH 3 ]/[NO] are essential for the denitration reaction. Both NO conversion and Hg 0 removal efficiency could reach more than 80% when NO and Hg 0 were removed simultaneously using Mn0.8Ti at 240°C. Hg 0 removal efficiency slightly declined as the Mn content increased in the catalysts. The reaction temperature had no significant effect on Hg 0 removal efficiency. O 2 and HCl had a promotional effect on Hg 0 removal. SO 2 and NH 3 were observed to weaken Hg 0 removal because of competitive adsorption. NO first facilitated Hg 0 removal and then had an inhibiting effect as NO concentration increased without O 2 , and it exhibited weak inhibition of Hg 0 removal efficiency in the presence of O 2 . The oxidation of Hg 0 on MnO x /TiO 2 follows the Mars-Maessen and Langmuir-Hinshelwood mechanisms. Copyright © 2016. Published by Elsevier B.V.

Magnetic properties of (Mn1-xRux)3Ga alloys

International Nuclear Information System (INIS)

Hori, T.; Akimitsu, M.; Miki, H.; Ohoyoama, K.; Yamaguchi, Y.

2002-01-01

We found that the pseudo binary alloys Mn 1-x Ru x 3 Ga, with 0.33≤x≤0.67, have an ordered b.c.c. structure. The lattice constant a is almost constant with respect to x: a=6.000 A for x=0.33 and a=5.992 A for x=0.67. For the alloy with x=0.33, i.e. Mn 2 RuGa, the magnetization is almost saturated in a field of 20 kOe. The saturation magnetization at 4.2 K is 23 emu/g, and the Curie temperature, T C , is 460 K. The T C of (Mn 1-x Ru x ) 3 Ga decreases almost linearly with increasing x, and it vanishes around x=0.67 (MnRu 2 Ga). We also determined atomic and magnetic structures from neutron diffraction experiments. The alloy Mn 2 RuGa (x=0.33) has an ordered structure of CuHg 2 Ti type; the magnetic Mn atoms mainly occupy the 4a (0,0,0) and 4d (3/4,3/4,3/4) sites. We also observed that the magnetic moments of Mn atoms on the 4a and 4d sites are antiparallel to each other; values of the magnetic moment are μ a =4.6 and μ d =3.3 μ B per Mn atom. (orig.)

Effect of thermomechanical treatments on phase distribution and microstructure evolution of a Ti-48Al-2Mn-2Nb alloy

International Nuclear Information System (INIS)

Morris, M.A.; Leboeuf, M.

1995-01-01

Titanium aluminide alloys based on TiAl offer potential benefits as intermetallics for structural applications due to their low density and attractive properties at high temperature. However, their strength and ductility are very dependent on microstructural morphologies and much research is being devoted to obtaining optimal properties. The large grain sizes and solute segregations associated with conventional castings have forced much of the work to be focused on obtaining finer microstructures, both in terms of grain sizes as well as lamellar spacings. Thermomechanical treatments have been used to produce a large variety of structural morphologies ranging from fully lamellar to duplex and equiaxed and in which the proportion of each phase is also variable. By choosing the correct temperature and strain rate parameters, it may be possible to modify the microstructure by dynamic recrystallization, if during the mechanical process the lamellae of the α 2 phase can be broken down and be used to accelerate the kinetics of nucleation of the new γ grains. The present study has been carried out in order to examine this process and the authors have compared the different refined microstructures that can be obtained by a new thermomechanical process (ELIT pack-rolling) of a Ti-48Al-2Mn-2Nb alloy with respect to those obtained by heat treatments only

Synthesis and Analysis of MnTiO3 Thin Films on ITO Coated Glass Substrates

Science.gov (United States)

Martin, Emerick; Sahiner, Mehmet-Alper

Perovskites like Manganese Titanium Oxide have interesting chemical properties that may be advantageous to the development of p-n junction photovoltaic cells. Due to the limited understanding behind the compound, it is essential to know the characteristics of it when it is deposited in thin film form. The cells were created using pulsed laser deposition method for two separate mediums (first layers after ITO). ZnO was deposited onto ITO glass for the first sample. For the second sample, a layer of pure Molybdenum was deposited onto the ITO glass. The MnTiO3 was then deposited onto both samples. There was a target thickness of 1000 Angstroms, but ellipsometry shows that, for the Mo based sample, that film thickness was around 1500 Angstroms. There were inconclusive results for the ZnO based sample. The concentration of active carriers was measured using a Hall Effect apparatus for the Mo based sample. The XRD analyses were used to confirm the perovskite structure of the films. Measurements for photoelectric conversion efficiency were taken using a Keathley 2602 ScourceMeter indicated low values for efficiency. The structural information that is correlated with the low electrical performance of this sample will be discussed. SHU-NJSGC Summer 2015 Fellowship.

Synthesis dependent characteristics of Sr1−xMnxTiO3 (x=0.03, 0.05, 0.07 and 0.09)

International Nuclear Information System (INIS)

Preethi Meher, K.R.S.; Bogicevic, Christine; Janolin, Pierre-Eymeric; Varma, K.B.R.

2012-01-01

Sr 1−x Mn x TiO 3 (where x=0.03, 0.05, 0.07 and 0.09) was synthesized via different routes that include solid-state, oxalate precipitation and freeze drying. In oxalate precipitation technique, compositions corresponding to 3 and 5 mol% doping of Mn were monophasic whereas the higher compositions revealed the presence of the secondary phases such as MnO, Mn 3 O 4 etc., as confirmed by high resolution X-ray diffraction (XRD) studies. The decomposition behavior of the precursors prepared using oxalate precipitation method corresponding to the above mentioned compositions was studied. Nanopowders of compositions pertaining to 5 to 9 mol% of Mn doping were obtained using freeze–drying technique. The average crystallite size of these nanopowders was found to be in the 35 to 65 nm range. The microstructural studies carried out on the sintered ceramics, fabricated using powders synthesized by different routes established the fine grained nature ( 1−x Mn x TiO 3 (x=0.03 and 0.05) obtained by oxalate precipitation technique along with that of the nanopowders for x=0.05, 0.07 and 0.09 obtained by freeze drying method, microstructural characterization and synthesis dependent dielectric behavior. Highlights: ► Monophasic samples obtained for compositions Sr 1−x Mn x TiO 3 with x=0.03 and 0.05. ► Nanopowders of Sr 1−x Mn x TiO 3 with x=0.05, 0.07 and 0.09 were synthesized by freeze–drying method. ► Phase purity of samples synthesized using freeze drying method were studied at different sintering temperatures. ► Analysis of Raman spectra for samples prepared by both oxalate precipitation and freeze–drying. ► Microstructure dependent dielectric characteristics have been illustrated.

Structural stability and depolarization of manganese-doped (Bi₀.₅Na₀.₅){sub 1−x}Ba{sub x}TiO₃ relaxor ferroelectrics

Energy Technology Data Exchange (ETDEWEB)

Wang, Sheng-Fen [Department of Physics, Fu Jen Catholic University, New Taipei City 24205, Taiwan (China); Tu, Chi-Shun, E-mail: 039611@mail.fju.edu.tw [Department of Physics, Fu Jen Catholic University, New Taipei City 24205, Taiwan (China); Graduate Institute of Applied Science and Engineering, Fu Jen Catholic University, New Taipei City 24205, Taiwan (China); Chang, Ting-Lun; Chen, Pin-Yi [Department of Mechanical Engineering, Ming-Chi University of Technology, New Taipei City 24301, Taiwan (China); Chen, Cheng-Sao [Department of Mechanical Engineering, Hwa-Hsia University of Technology, New Taipei City 23567, Taiwan (China); Hugo Schmidt, V. [Department of Physics, Montana State University, Bozeman, Montana 59717 (United States); Anthoniappen, J. [Graduate Institute of Applied Science and Engineering, Fu Jen Catholic University, New Taipei City 24205, Taiwan (China)

2014-10-21

This work reveals that 0.5 mol. % manganese (Mn) doping in (Bi₀.₅Na₀.₅){sub 1−x}Ba{sub x}TiO₃ (x = 0 and 0.075) solid solutions can increase structural thermal stability, depolarization temperature (T{sub d}), piezoelectric coefficient (d₃₃), and electromechanical coupling factor (kₜ). High-resolution X-ray diffraction and transmission electron microscopy reveal coexistence of rhombohedral (R) R3c and tetragonal (T) P4bm phases in (Bi₀.₅Na₀.₅)₀.₉₂₅Ba₀.₀₇₅TiO₃ (BN7.5BT) and 0.5 mol. % Mn-doped BN7.5BT (BN7.5BT-0.5Mn). (Bi₀.₅Na₀.₅)TiO₃ (BNT) and BN7.5BT show an R − R + T phase transition, which does not occur in 0.5 mol. % Mn-doped BNT (BNT-0.5Mn) and BN7.5BT-0.5Mn. Dielectric permittivity (ε′) follows the Curie-Weiss equation, ε′ = C/(T − T{sub o}), above the Burns temperature (T_B), below which polar nanoregions begin to develop. The direct piezoelectric coefficient (d₃₃) and electromechanical coupling factor (kₜ) of BN7.5BT-0.5Mn reach 190 pC/N and 47%.

Efficient degradation of H2S over transition metal modified TiO2 under VUV irradiation: Performance and mechanism

Science.gov (United States)

Liu, Gaoyuan; Ji, Jian; Hu, Peng; Lin, Sixin; Huang, Haibao

2018-03-01

Odor pollution causes great harm to the atmospheric environment and human health. H2S, as an odor gas, is highly toxic and corrosive and thus requires removal efficiently. In this study, TiO2 catalysts modified by transition metals including Mn, Cu, Ni and Co, were prepared using a modified sol-gelatin method and tested under UV-PCO or VUV-PCO process. H2S degradation was great enhanced in VUV-PCO compared with conventional UV-PCO. Among the catalysts, 1 wt% Mn-TiO2 showed the highest removal efficiency of 89.9%, which is 30 times higher than that under 254 nm UV irradiation. Residual ozone in the outlet can be completely eliminated by Mn-TiO2. Photocatalytic oxidation, photolysis and ozone-assisted catalytic oxidation all involved in the VUV-PCO process and their contribution were determined by H2S removal efficiency.

Characterization and electrochemical performance of lithium-active titanium dioxide inlaid LiNi0.5Co0.2Mn0.3O2 material prepared by lithium residue-assisted method

International Nuclear Information System (INIS)

Li, Lingjun; Chen, Zhaoyong; Song, Liubin; Xu, Ming; Zhu, Huali; Gong, Li; Zhang, Kaili

2015-01-01

Highlights: • LiTiO 2 -inlaid LiNi 0.5 Co 0.2 Mn 0.3 O 2 is prepared by lithium residue-assisted method. • The unique inlaid architecture inherits the advantages of coating and doping. • LiTiO 2 inlaying enhances the pristine at high cyclability and rate properties. • Excess LiTiO 2 modification results in low Li + diffusion coefficient. • The 3 mol% LiTiO 2 inlaid sample exhibits the best electrochemical performance. - Abstract: The lithium residues are consumed as raw materials to in-situ synthesize the LiTiO 2 -inlaid LiNi 0.5 Co 0.2 Mn 0.3 O 2 composites. The effects of various LiTiO 2 contents on the morphology, structure, and electrochemical properties of LiNi 0.5 Co 0.2 Mn 0.3 O 2 materials are investigated in detail. Energy dispersive spectrometer mapping, high-resolution transmission electron microscopy and fast Fourier transform analysis confirm that the spherical particles of LiNi 0.5 Co 0.2 Mn 0.3 O 2 are completely coated by crystalline LiTiO 2 phase; X-ray diffraction, cross-section SEM and corresponding EDS results indicate that Ti ions are also doped into the bulk LiNi 0.5 Co 0.2 Mn 0.3 O 2 with gradient distribution. Electrochemical tests show that the LiTiO 2 -inlaid samples exhibit excellent reversible capacity, enhanced cyclability, superior lithium diffusion coefficient and rate properties. Specially, the 3 mol% LiTiO 2 inlaid sample maintains 153.7 mA h g −1 with 94.4% capacity retention after 100 cycles between 2.7–4.4 V at 1 C, take 30% advantage than that of the pristine one (118.2 mA h g −1 ). This improvement can be attributed to the removal of lithium residues and suitable LiTiO 2 inlaying. The absence of lithium residue is helpful to retard the decomposition of LiPF 6 . While, suitable LiTiO 2 inlaying can protect the bulk from directly contacting the electrolyte, buffer the volume change of core and shell during cycles, increase the surface electronic conductivity and offer a 3D path for Li + diffusion from the bulk to

Magnetocapacitance of BaZr0.2Ti0.8O3 and La0.67Sr0.33MnO3 thin film heterostructures

International Nuclear Information System (INIS)

Tarale, A.N.; Padal, N.T.; Salunkhe, D.J.; Joshi, P.B.; Kulkarni, S.B.; Reddy, V.R.

2012-01-01

The present paper reports MD properties of BaZr 0.2 Ti 0.8 O 3 and La 0.67 Sr 0.33 MnO 3 (LSMO) thin film multilayer composite. The BZT is known to be relaxer possessing Curie temperature in vicinity of room temperature while LSMO is a CMR material possessing T c at room temperature. The Magnetoresistance of LSMO is known to cause change in intragrain interfacial polarization as function of applied magnetic field and dielectric constant ε H changes with applied magnetic field. From the literature survey it is observed that the MD properties based on CMR phenomena are not well investigated and efforts towards further exploration of these phenomena are required. Recent reports also indicate that that the magneto capacitance posses the contribution due giant magnetostriction of LMSO. The BZT as well as LSMO gels are synthesized using modified Pechini method. Initially hydroxide precipitates of Ba, Zr, Ti and La, Sr, Mn are dissolved in citric acid to form citrates of cations individually. The citrate solution is polymerized by addition of ethylene glycol and used as a coating solution. The alternate layers of thin films of BZT and LSMO are deposited on SiO 2 /nSi(100) substrate. The nanoparticles heterostructure are formed by sintering the thin films at 800 deg C. The thin films are investigated for crystal structure, morphology, dielectric constant, and complex impedance as a function of frequency f up to 1 MHz and magnetic field up to 5 kOe respectively. It is observed that the thin film composites exhibits magnetocapacitance of 8.3% for 1 KHz and possess a finite value even at 1MHz. The observed variation of impedance spectra in terms of Maxwell-Wagner model and in the light of the recent observation by Xiaodong Tang, et al. 2011. (author)

Disorder influence on the magnetic properties of La{sub 0.55}Sr{sub 0.45}MnO{sub 3}/SrTiO{sub 3} superlattices

Energy Technology Data Exchange (ETDEWEB)

Haberkorn, N. E-mail: nhaberk@cab.cnea.gov.ar; Sirena, M.; Guimpel, J.; Steren, L.B

2004-05-01

The structural and physical properties of La{sub 0.55}Sr{sub 0.45}MnO{sub 3}/SrTiO{sub 3} superlattices grown by magnetron sputtering are studied. Two deposition temperatures and different mismatched substrates and buffer layers were used. The structure was determined by refinement through X-ray diffraction pattern fitting. The results indicate 1 unit cell (u.c.) interdiffusion at the interfaces and a 1 u.c. layer thickness fluctuation, i.e. roughness. In-plane hysteresis loops show the expected ferromagnetic behavior, while the perpendicular-to-plane hysteresis loops show anomalies which could evidence magnetic domain size inhomogeneities and stress.

Metallic and Insulating Interfaces of Amorphous SrTiO3-Based Oxide Heterostructures

DEFF Research Database (Denmark)

Chen, Yunzhong; Pryds, Nini; Kleibeuker, Josée E.

2011-01-01

AlO3, SrTiO3, and yttria-stabilized zirconia films. On the other hand, samples of amorphous La7/8Sr1/8MnO3 films on SrTiO3 substrates remain insulating. The interfacial conductivity results from the formation of oxygen vacancies near the interface, suggesting that the redox reactions on the surface...

Chemical deposition of La0.7Ca0.3MnO3±δ films on ceramic substrates

Directory of Open Access Journals (Sweden)

Cássio Morilla-Santos

2011-01-01

Full Text Available In this paper, it is reported the growth of La0.7Ca0.3MnO3±δ films using a chemical solution deposition method (CSD by the spin-coating technique. Such solution was prepared through a route based on modified polymeric precursor method. Spin-coating deposition on different ceramic substrates was performed and analyzed by X-ray diffraction (XRD, scanning electron microscopy (SEM and X-ray photoelectron spectroscopy (XPS. The magnetic response of the prepared specimens was studied using a SQUID magnetometer. The obtained results indicated uniform deposition on SrTiO3 and LaAlO3 substrates with similar characteristics. Furthermore, significant differences were detected in the Mn3+/Mn4+ valence ratio and a corresponding diverse magnetic response was observed. The sample prepared on SrTiO3 and LaAlO3 presented a critical temperature around 270 K as expected.

Electrochemistry and safety of Li 4Ti 5O 12 and graphite anodes paired with LiMn 2O 4 for hybrid electric vehicle Li-ion battery applications

Science.gov (United States)

Belharouak, Ilias; Koenig, Gary M.; Amine, K.

A promising anode material for hybrid electric vehicles (HEVs) is Li 4Ti 5O 12 (LTO). LTO intercalates lithium at a voltage of ∼1.5 V relative to lithium metal, and thus this material has a lower energy compared to a graphite anode for a given cathode material. However, LTO has promising safety and cycle life characteristics relative to graphite anodes. Herein, we describe electrochemical and safety characterizations of LTO and graphite anodes paired with LiMn 2O 4 cathodes in pouch cells. The LTO anode outperformed graphite with regards to capacity retention on extended cycling, pulsing impedance, and calendar life and was found to be more stable to thermal abuse from analysis of gases generated at elevated temperatures and calorimetric data. The safety, calendar life, and pulsing performance of LTO make it an attractive alternative to graphite for high power automotive applications, in particular when paired with LiMn 2O 4 cathode materials.

Substrate-induced strain effects on Pr0.6Ca0.4MnO3 films

International Nuclear Information System (INIS)

Nelson, C S; Hill, J P; Gibbs, Doon; Rajeswari, M; Biswas, A; Shinde, S; Greene, R L; Venkatesan, T; Millis, A J; Yokaichiya, F; Giles, C; Casa, D; Venkataraman, C T; Gog, T

2004-01-01

We report the characterization of the crystal structure, low-temperature charge and orbital ordering, transport and magnetization of Pr 0.6 Ca 0.4 MnO 3 films grown on LaAlO 3 , NdGaO 3 and SrTiO 3 substrates, which provide compressive (LaAlO 3 ) and tensile (NdGaO 3 and SrTiO 3 ) strain. The films are observed to exhibit different crystallographic symmetries from the bulk material and the low-temperature ordering is found to be more robust under compressive as opposed to tensile strain. In fact, bulk-like charge and orbital ordering is not observed in the film grown on NdGaO 3 , which is the substrate that provides the least amount of measured, but tensile, strain. This result suggests the importance of the role played by the Mn-O--Mn bond angles in the formation of charge and orbital ordering at low temperatures. Finally, in the film grown on LaAlO 3 , a connection between the lattice distortion associated with orbital ordering and the magnetization is reported

Multiferroic behavior on nanometric La2/3Ca1/3MnO3 / BaTiO3 bilayers

Science.gov (United States)

Prieto, Pedro; Ordoñez, John Edward; Gomez, Maria Elena; Lopera, Wilson

2014-03-01

We have deposited bilayers of the FM La2/3Ca1/3MnO3 and FE BaTiO3 as a route to design systems with artificial magnetoelectric coupling on LCMO/BTO/Nb:STO system. We maintain a fixed magnetic layer thickness (tLCMO = 48 nm) and varying the thickness of the ferroelectric layer (tBTO = 20, 50, 100 nm). We analyze the influence of the thickness ratio (tBTO/ tLCMO) in electrical and magnetic properties of manganite. From X-ray diffraction analysis we observed that the samples grew textured. Magnetization and transport measurements indicate a possible multiferroic behavior in the bilayer. We found an increase in the Curie and metal-insulator transition temperature in the bilayer in comparison with those for LCMO (48nm)/STO. Hysteresis loops on bilayers show ferromagnetic behavior. This work has been supported by the ``El Patrimonio Autónomo Fondo Nacional de Financiamiento para CT&I FJC'' Colciencias-CENM Research Projects: No. 1106-48-925531 and CI7917-CC 10510 contract 0002-2013 COLCIENCIAS-UNIVALLE.

Recent development of the Cu/Nb-Ti superconducting cables for SSC in Hitachi Cable, Ltd

International Nuclear Information System (INIS)

Sakai, S.; Iwaki, G.; Sawada, Y.; Moriai, H.; Ishigami, Y.

1989-01-01

In these few years, Cu/Nb-Ti superconducting cables for the dipole magnets of SSC projects have been developed in the industrial scale in Hitachi Cable, Ltd. The features of these developed conductors are as follows. (1) The diameter of Nb-Ti filaments is very small, 4-6 μm. (2) The critical current density (J c ) is very high, 2,850-3,050 A/mm 2 at 5 T on wires, 2750-2950 A/mm 2 at 5 T on cables in industrial scale. The champion J c of wires is 3,460 A/mm 2 at 5 T in the laboratory scale. (3) The RRR Residual Resistivity Ratio values of developed cables is very high, approximately 200, due to the newly developed high purity Oxygen Free Copper (OFC). (4) The conductors have been wound to the 1 m length dipole magnet in Hitachi Ltd., and it has generated 6.7 T in the central magnetic field at 6,595 A. The Cu/Cu-Mn/Nb-Ti composite wires which avoid the possibility of electrical coupling of the filaments have been produced in laboratory scale. The RRR of the copper stabilizer and J c properties have not degraded because of no metallurgical reactions between Cu and Mn, Nb-Ti and Mn. 7 refs., 9 figs., 4 tabs

Dielectric functions and energy band gap variation studies of manganese doped Bi{sub 3.25}La{sub 0.75}Ti{sub 3}O{sub 12} thin films using spectroscopic ellipsometry

Energy Technology Data Exchange (ETDEWEB)

Gautam, Prikshit, E-mail: pgautam.phy.du@gmail.com [Department of Physics and Astrophysics, University of Delhi (DU), Delhi 110007 (India); Department of Physics Kirori Mal College, University of Delhi, Delhi 110007 (India); Sachdeva, Anupama [Department of Physics and Astrophysics, University of Delhi (DU), Delhi 110007 (India); Singh, Sushil K. [Functional Materials Division, SSPL, Timarpur, New Delhi 110054 (India); Tandon, R.P., E-mail: ram_tandon@hotmail.com [Department of Physics and Astrophysics, University of Delhi (DU), Delhi 110007 (India)

2014-12-25

Highlights: • Mn Doped Bi{sub 3.25}La{sub 0.75}Ti{sub 3}O{sub 12} (BLT) thin films prepared by chemical solution deposition technique. • Raman spectroscopy of these films shows that Mn{sup 3+} is well substituted at Ti{sup 4+} site. • The optical properties of BLT and Mn modified BLT thin films were investigated by using spectroscopic ellipsometry. • A double Tauc–Lorentz (DTL) dispersion relation was successfully used to model the dielectric functions. • The direct optical band gap (Eg{sup d}) is found to decrease with increase in Mn content. - Abstract: Single phase polycrystalline Mn-modified Bi{sub 3.25}La{sub 0.75}Ti{sub 3}O{sub 12} (BLT) thin films were prepared by chemical solution deposition method using spin coating technique on Pt/Ti/SiO{sub 2}/Si (1 0 0) substrates. Raman spectroscopy of these films shows that Mn{sup 3+} is well substituted at Ti{sup 4+} site. The optical properties of BLT and Mn modified BLT thin films were investigated at room temperature by using spectroscopic ellipsometry (SE) in the energy range 0.72–6.2 eV. A double Tauc–Lorentz (DTL) dispersion relation was successfully used to model the dielectric functions of these films where a shift to the lower energy side with Mn doping is seen. The full width at half maxima (FWHM) (Γ) of dielectric function is found to increase with Mn doping. This increase in FWHM may be attributed to the increase in the trap density in forbidden band which consequently decreases the value of direct optical band gap (Eg{sup d}). The direct optical band gap (Eg{sup d}) is found to decrease with increase in Mn content in the studied composition range. This decrease in Eg{sup d} with doping may be attributed to the variation in the defect concentration present in the structure.

Hierarchically structured Co₃O₄@Pt@MnO₂ nanowire arrays for high-performance supercapacitors.

Science.gov (United States)

Xia, Hui; Zhu, Dongdong; Luo, Zhentao; Yu, Yue; Shi, Xiaoqin; Yuan, Guoliang; Xie, Jianping

2013-10-17

Here we proposed a novel architectural design of a ternary MnO2-based electrode - a hierarchical Co3O4@Pt@MnO2 core-shell-shell structure, where the complemental features of the three key components (a well-defined Co3O4 nanowire array on the conductive Ti substrate, an ultrathin layer of small Pt nanoparticles, and a thin layer of MnO2 nanoflakes) are strategically combined into a single entity to synergize and construct a high-performance electrode for supercapacitors. Owing to the high conductivity of the well-defined Co3O4 nanowire arrays, in which the conductivity was further enhanced by a thin metal (Pt) coating layer, in combination with the large surface area provided by the small MnO2 nanoflakes, the as-fabricated Co3O4@Pt@MnO2 nanowire arrays have exhibited high specific capacitances, good rate capability, and excellent cycling stability. The architectural design demonstrated in this study provides a new approach to fabricate high-performance MnO2-based nanowire arrays for constructing next-generation supercapacitors.

Structure and properties of selected cemented carbides and cermets covered with TiN/(Ti,Al,SiN/TiN coatings obtained by the cathodic arc evaporation process

Directory of Open Access Journals (Sweden)

Leszek A. Dobrzañski

2005-06-01

Full Text Available This study presents the results of microstructural examinations, mechanical tests and service performance tests carried out on thin TiN/(Ti,Al,SiN/TiN wear resistance coatings obtained by the CAE process on cermet and cemented carbide substrates. Microstructural examinations of the applied coatings and the substrate were made with an OPTON DSM 940 SEM and a LEICA MEF4A light microscope. Adhesion of the coatings on cemented carbides and cermets was measured using the scratch test. The cutting properties of the materials were determined from service tests in which continuous machining of C45E steel was carried out. The hardness of the substrate and the microhardness of the coatings were determined with a DUH 202 SHIMADZU ultra microhardness tester with a load of 70 mN. Roughness tests were also carried out before applying the coatings and after the PVD process. Cutting tests confirmed the advantages of the TiN/(Ti,Al,SiN/TiN type coatings obtained using the PVD method in the CAE mode on cemented carbides and cermets, as a material that undergoes very low abrasive, thermal and adhesion wear. These coatings extend tool life compared to commercially available uncoated tools with single and multi-layer coatings deposited using PVD/CVD methods.

Replication of Annual Cycles in Mn in Hudson River Cores: Mn Peaks During High Water Flow

Science.gov (United States)

Abbott, D. H.; Hutson, D.; Marrero, A. M.; Block, K. A.; Chang, C.; Cai, Y.

2017-12-01

Using the results from an ITRAX, XRF scanner, we previously reported apparent annual cycles in Mn in a single, high sedimentation rate Hudson River core, LWB1-8, taken off Yonkers, NY (Carlson et al., 2016). We replicated these results in three more high sedimentation rate cores and found stratigraphic markers that verify our inferences about the annual nature of the Mn cycles. The three new cores are LWB4-5 taken off Peekskill, NY, and LWB3-44 and LWB3-25, both taken in Haverstraw Bay. The cores are from water depths of 7-9 meters and all have high magnetic susceptibilities (typically > 30 cgs units) in their upper 1 to 2 meters. The high susceptibilities are primarily produced by magnetite from modern industrial combustion. One core, LWB1-8, has reconnaissance Cs dates that verify the annual nature of the cycles. More Cs dates are expected before the meeting. We developed several new methods of verifying the annual nature of our layer counts. The first is looking at the grain size distribution and age of layers with unusually high Mn peaks. Peaks in Si, Ni and Ti and peaks in percentage of coarse material typically accompany the peaks in Mn. Some are visible as yellow sandy layers. The five highest peaks in Mn in LWB1-8 have layer counted ages that correspond (within 1 year in the top meter and within 2 years in the bottom meter) to 1996, 1948, 1913, 1857 and 1790. The latter three events are the three largest historical spring freshets on the Hudson. 1996 is a year of unusually high flow rate during the spring freshet. Based on our work and previous work on Mn cycling in rivers, we infer that the peaks in Mn are produced by extreme erosional events that erode sediment and release pore water Mn into the water column. The other methods of testing our chronology involve marine storms that increase Ca and Sr and a search for fragments of the Peekskill meteorite that fell in October 1992. More information on the latter will be available by the meeting.

Enhancing Photocatalytic Activity on (MnO@TNTAs):Mn2+ with a Hierarchical Sandwich-Like Nanostructure via a Two-Step Procedure

Science.gov (United States)

Kong, Junhan; Zhang, Wei; Zhang, Yubo; Xia, Minghao; Wu, Xiuling; Wang, Yongqian

2018-02-01

Several semiconductor nanomaterial devices are increasingly being applied in a variety of fields, especially in the treating of environmental pollutants. We have fabricated (MnO@TNTAs):Mn2+ with sandwich-like nanostructures composed of TiO2 nanotube arrays (TNTAs), Mn-doped TNTAs and MnO. The experimental procedure was a two-step synthesis: first, using anodic oxidation methods and then hydrothermal methods. We carried out many characterizations of the "sandwiches" in the nanoscale. From the field emission scanning electron microscopy images we found nanofibers lying on the highly-ordered nanotube arrays. The diameter of the nanotubes was about 50 nm but the size of the nanofibers varied. Energy dispersive spectroscopy demonstrated that the nanofibers contained a manganese element and x-ray diffraction patterns showed the peak of the manganosite phase. From ultraviolet-visible light spectra, it was found that the nanostructures had strong absorption activities under both ultraviolet and visible light radiation, while pure TNTAs had absorption only under ultraviolet light. The photodegradation experiments proved that the sandwich-like nanostructures had an excellent photocatalytic activity (92.5% after 240 min), which was a great improvement compared with pure TNTAs. In this way, the structures as a device at the nanoscale have a huge potential in controlling environmental pollution.

Assessing electron beam sensitivity for SrTiO{sub 3} and La{sub 0.7}Sr{sub 0.3}MnO{sub 3} using electron energy loss spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Nord, Magnus, E-mail: magnunor@gmail.com [Department of Physics, NTNU, Trondheim (Norway); Vullum, Per Erik [Department of Physics, NTNU, Trondheim (Norway); Materials and Chemistry, SINTEF, Trondheim (Norway); Hallsteinsen, Ingrid; Tybell, Thomas [Department of Electronics and Telecommunications, NTNU, Trondheim (Norway); Holmestad, Randi [Department of Physics, NTNU, Trondheim (Norway)

2016-10-15

Thresholds for beam damage have been assessed for La{sub 0.7}Sr{sub 0.3}MnO{sub 3} and SrTiO{sub 3} as a function of electron probe current and exposure time at 80 and 200 kV acceleration voltage. The materials were exposed to an intense electron probe by aberration corrected scanning transmission electron microscopy (STEM) with simultaneous acquisition of electron energy loss spectroscopy (EELS) data. Electron beam damage was identified by changes of the core loss fine structure after quantification by a refined and improved model based approach. At 200 kV acceleration voltage, damage in SrTiO{sub 3} was identified by changes both in the EEL fine structure and by contrast changes in the STEM images. However, the changes in the STEM image contrast as introduced by minor damage can be difficult to detect under several common experimental conditions. No damage was observed in SrTiO{sub 3} at 80 kV acceleration voltage, independent of probe current and exposure time. In La{sub 0.7}Sr{sub 0.3}MnO{sub 3}, beam damage was observed at both 80 and 200 kV acceleration voltages. This damage was observed by large changes in the EEL fine structure, but not by any detectable changes in the STEM images. The typical method to validate if damage has been introduced during acquisitions is to compare STEM images prior to and after spectroscopy. Quantifications in this work show that this method possibly can result in misinterpretation of beam damage as changes of material properties. - Highlights: • We studied the effects of a TEM electron beam on a perovskite heterostructure. • Using an improved ELNES quantification method, subtle changes could be observed. • On LSMO changes were observed in the ELNES, but none in the STEM-HAADF. • For STO changes were observed in both ELNES and STEM-HAADF. • This shows beam damage can be misinterpreted as material properties.

Substitution studies of Mn and Fe in Ln{sub 6}W{sub 4}Al{sub 43} (Ln=Gd, Yb) and the structure of Yb{sub 6}Ti{sub 4}Al{sub 43}

Energy Technology Data Exchange (ETDEWEB)

Treadwell, LaRico J.; Watkins-Curry, Pilanda [Department of Chemistry, Louisiana State University, Baton Rouge, LA 70803 (United States); Department of Chemistry, University of Texas at Dallas, Richardson, TX 75080 (United States); McAlpin, Jacob D. [Department of Chemistry, Louisiana State University, Baton Rouge, LA 70803 (United States); Prestigiacomo, Joseph; Stadler, Shane [Department of Physics and Astronomy, Louisiana State University, Baton Rouge, LA 70803 (United States); Chan, Julia Y., E-mail: Julia.Chan@utdallas.edu [Department of Chemistry, Louisiana State University, Baton Rouge, LA 70803 (United States); Department of Chemistry, University of Texas at Dallas, Richardson, TX 75080 (United States)

2014-02-15

The synthesis and characterization of Mn- and Fe-substituted Ln{sub 6}W{sub 4}Al{sub 43} (Ln=Gd, Yb) and Yb{sub 6}Ti{sub 4}Al{sub 43} are reported. The compounds adopt the Ho{sub 6}Mo{sub 4}Al{sub 43} structure type with lattice parameters of a∼11 Å and c∼17.8 Å with structural site preferences for Mn and Fe. The magnetization of Yb{sub 6}W{sub 4}Al{sub 43} is sensitive to Mn and Fe doping, which is evident by an increase in the field dependent magnetization. Gd{sub 6}W{sub 4}Al{sub 43}, Gd{sub 6}W{sub 4}Al{sub 42.31(11)}Mn{sub 0.69(11)}, and Gd{sub 6}W{sub 4}Al{sub 41.69(12)}Fe{sub 1.30(12)} order antiferromagnetically in the ab- and c-directions at 15, 14, and 13 K, respectively, with positive Weiss constants, suggesting the presence of ferromagnetic exchange interactions. Anisotropic magnetization data of Gd{sub 6}W{sub 4}Al{sub 43−y}T{sub y} (T=Mn, Fe) analogs are discussed. - Graphical abstract: The magnetic susceptibility of Ln{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} (Ln = Gd, Yb; T= Mn, Fe). Display Omitted - Highlights: • Single crystals of Ln{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} were grown with Al-flux. • Anisotropic magnetic behavior were determined on single crystals. • Gd{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} (T=Mn, Fe) analogs order antiferromagnetically.

Magnetic properties of Fe-rich rare-earth intermetallic compounds with a ThMn12 structure

International Nuclear Information System (INIS)

Ohashi, K.; Tawara, Y.; Osugi, R.; Shimao, M.

1988-01-01

Sm(Fe/sub 1-//sub x/M/sub x/) 12 ternary compounds based on the tetragonal ThMn 12 structure where M is Ti, Si, V, Cr, and Mo were investigated. M atoms have a preference for site occupation. Ti atoms occupy the 8i or 8j site and Cr atoms occupy the 8i site. Curie temperatures on Sm(M,Fe) 12 compounds are around 590 K except for the SmMo 2 Fe 10 compound (T/sub c/ = 483 K). The SmTiFe 11 and SmSi 2 Fe 10 compounds have a high saturation magnetization and magnetic anisotropy

Electronic structure of homoleptic transition metal hydrides: TiH4, VH4, CrH4, MnH4, FeH4, CoH4, and NiH4

International Nuclear Information System (INIS)

Hood, D.M.; Pitzer, R.M.; Schaefer III, H.F.

1979-01-01

Ab initio molecular electronic structure theory has been applied to the family of transition metal tetrahydrides TiH 4 through NiH 4 . For the TiH 4 molecule a wide range of contracted Gaussian basis sets has been tested at the self-consistent-field (SCF) level of theory. The largest basis, labeled M(14s 11p 6d/10s 8p 3d), H(5s 1p/3s 1p), was used for all members of the series and should yield wave functions approaching true Hartree-Fock quality. Predicted SCF dissociation energies (relative to M+4H) and M--H bond distances are TiH 4 132 kcal, 1.70 A; VH 4 86 kcal, 1.64 A; CrH 4 65 kcal, 1.59 A; MnH 4 -- 36 kcal, 1.58 A; FeH 4 0 kcal, 1.58 A; CoH 4 27 kcal, 1.61 A; and NiH 4 18 kcal, 1.75 A. It should be noted immediately that each of these SCF dissociation energies will be increased by electron correlation effects by perhaps as much as 90 kcal. For all of these molecules except TiH 4 excited states have also been studied. One of the most interesting trends seen for these excited states is the shortening of the M--H bond as electrons are transferred from the antibonding 4t 2 orbital to the nonbonding 1e orbitals

Thermal activation energies and peak temperatures in thermoluminescence of LiF (Mg, Ti) and CaF2:Mn at low temperatures

International Nuclear Information System (INIS)

Jain, V.K.; Jahan, M.S.

1987-01-01

Low temperature thermoluminescence (TL) of LiF (TLD-100) and CaF 2 :Mn is studied. The TLD-100 is dosimetry grade LiF manufactured by Harshaw-Filtrol Partnership. It is believed that it contains about 200 ppm Mg and 7 ppm Ti as impurities. In each case the glow curve shows several peaks. Some of these peaks are quite strong and develop with dose. Others are weak. Kinetic parameters are calculated for the former using the initial rise method and Chen's modified formula. The two sets of values are found to be different. Some authors have suggested empirical formulae connecting peak temperature, T m , and activation energy, E. The empirical relations are tried for the values of E calculated, as well as those available in literature (for T m above room temperature). It is found that a fairly reasonable relation existed between E and T m . (author)

Adhesion measurement of highly-ordered TiO2 nanotubes on Ti-6Al-4V alloy

Directory of Open Access Journals (Sweden)

Masoud Sarraf

2017-12-01

Full Text Available Self-assembled nanotubular arrays on Ti alloys could be used for more effective implantable devices in various medical approaches. In the present work, the adhesion of TiO2 nanotubes (TiO2 NTs on Ti-6Al-4V (Ti64 was investigated by laser spallation and scratch test techniques. At first, electrochemical anodization was performed in an ammonium fluoride solution dissolved in a 90:10 ethane-1,2-diol (ethylene glycol and water solvent mixture. This process was performed at room temperature (23 °C at a steady potential of 60 V for 1 h. Next, the TiO2 nanotubes layer was heat-treated to improve the adhesion of the coating. The formation of selforganized TiO2 nanotubes as well as the microstructural evolution, are strongly dependent on the processing parameters and subsequent annealing. From microscopic analysis, highly oriented arrays of TiO2 nanotubes were grown by thermal treatment for 90 min at 500 °C. Further heat treatment above 500 °C led to the detachment of the nanotubes and the complete destruction of the nanotubes occurred at temperature above 700 °C. Scratch test analysis over a constant scratch length (1000 µm indicated that the failure point was shifted from 247.4 to 557.9 µm while the adhesion strength was increased from ∼862 to ∼1814 mN after annealing at 500 °C. The adhesion measurement determined by laser spallation technique provided an intrinsic adhesion strength of 51.4 MPa for the TiO2 nanotubes on the Ti64 substrate.

Improvement of tribological properties of tool steels implanted with C+Ti

International Nuclear Information System (INIS)

Roman, E.; Segovia, J.L. de; Rodriguez, R.; Sanz, A.

1995-01-01

The chemical state and tribological properties of tempered and annealed steels (95MnCrW5 and 30CrMoV12) implanted with C+Ti has been studied by using the Auger sputtering depth profile and the ball on disk method to determine the wear parameters. The sample hardness was measured by the Vickers method. Friction coefficients are reduced by a factor of 0.8 for samples of steel 95MnCrW5 and by a factor of 0.4 for samples of 30CrMoV12 steel. The implanted 95MnCrW5 samples show a phase of mixed amorphous carbon and carbides. (author)

Material characteristic of Ti alloy (Ti-6Al-4V)

International Nuclear Information System (INIS)

Toyoshima, Noboru

1997-03-01

In regard to material characteristic of Ti alloy (Ti-6Al-4V), the following matters are provided by experiments. 1) In high temperature permeation behavior of implanted deuterium ion (0.5keV, 6.4 x 10 18 D + ions/m 2 s, ∼760deg K), the ratio of permeation flux to incident flux ranges from 3.3 x 10 -3 at 633deg K to 4.8 x 10 -3 at 753deg K. The activation energy of permeation is 0.12eV in this temperature region above 600deg K. At temperatures below 600deg K, the permeation flux of deuterium decreases drastically and the implanted ions remain in the alloy. 2) Radioactivation analysis using 14MeV fast neutron shows that Ti-6Al-4V alloy contains higher values of principal ingredients, Al, V, Fe, than that recorded at the chemical composition of Ti alloy, and also, contains impurities with Ni, Co and Mn. 3) Fraction of about 0.095wt% H 2 were absorbed in the test specimens, and tensile strength test was carried out. Under the condition of the hydrogen pressure 50 torr and temperature ∼500degC. The results show that there is no degradation in mechanical properties for absorption of with less than 0.04wt% H 2 . The tensile strength of wilding specimens have almost the same as that without wilding. Ti alloy, as a material of vacuum vessel of nuclear fusion device, must be selected to that with less impurities, particularly Co, by radioactivation analysis, and must be used under the temperature of 200-300degC, where hydrogen absorption does not make too progress. It is considered that Ti alloy can be used with less than 0.04wt% H 2 absorption in viewpoint of material mechanical strength. (author)

Influence of La and Sr addition on the structural parameter of PbTiO3

International Nuclear Information System (INIS)

Garcia, D.; Mascarenhas, Y.P.; Oliveira Paiva Santos, C. de; Eiras, J.A.

1989-01-01

Compositions of (Pb 1-x Ln x ) (Ti 1-y Mn y )O 3 (Ln = La, Sr; 0 0 C and sintered at 1200 0 C. The influence of the adition of La and Sr in the structural parameters of the tetragonal lattice of the lead titanate (PbTiO 3 ) was investigated with X-ray diffraction. The doping, with La or Sr, increase the lattice parameter a and decrease de parameter c of the PbTiO 3 . The variation of a and c increase with the dopant concentration and is greather in the La doped samples. The addition of 1% mol of Mn in these compositions increase the their sinterability. The apparent densites were compared with those calculated from the lattice parameters a and c. A decrease of the Curie temperature T c was observed when the concentration of La or Sr was increased. (author) [pt

Effect of Sr-doping of LaMnO3 spacer on modulation-doped two-dimensional electron gases at oxide interfaces

DEFF Research Database (Denmark)

Chen, Yunzhong; Gan, Yulin; Christensen, Dennis Valbjørn

2017-01-01

Modulation-doped oxide two-dimensional electron gas formed at the LaMnO3 (LMO) buffered disorderd-LaAlO3/SrTiO3 (d-LAO/LMO/STO) heterointerface provides new opportunities for electronics as well as quantum physics. Herein, we studied the dependence of Sr-doping of La1-xSrxMnO3 (LSMO, x = 0, 1/8, ...... of LSMO during the deposition of disordered LAO or that the energy levels of Mn 3d electrons at the interface of LSMO/STO are hardly varied even when changing the LSMO composition from LMO to SrMnO3....

Defect annealing in Mn/Fe-implanted TiO2(rutile)

CERN Document Server

Gunnlaugsson, H P; Masenda, H; Mølholt, T E; Johnston, K; Bharuth-Ram, K; Gislason, H; Langouche, G; Naidoo, D; Ólafsson, S; Svane, A; Weyer, G

2014-01-01

A study of the annealing processes and charge state of dilute Fe in rutile TiO2 single crystals was performed in the temperature range 143-662 K, utilizing online 57Fe emission Mossbauer spectroscopy following low concentrations ( 350 K.

High resolution imaging of La0.5Ba0.5MnO-LaMnO superlattice

International Nuclear Information System (INIS)

Shapoval, O.; Belenchuk, A.; Verbeeck, J.; Moshnyaga, V.

2013-01-01

Full text: Artificial low dimensional systems of tailored on atomic layer level manganites is a very promising class of materials for future spintronic applications. The high resolution transmission electron microscopy imaging provides a powerful approach to extract structural, chemical and functional information on atomic level in a real space. Recently, we have reported on the Metalorganic Aerosol Deposition synthesis and properties of superlattices (SL) composed from (LaMnO 3 ) n and (La 0.5 Ba 0.5 MnO 3 ) 2n with n=1-2 of perovskite monolayers. The functional properties of digitally synthesized SL are similar to the optimal doped 'bulk' thin film material. The similarities between their properties can be interpreted in frame of the many-body interactions responsible for the properties of the single-layer and bilayer manganites. This work presents the systematic studies of atomically resolved structure of (LaMnO 3 ) n /(La 0.5 Ba 0.5 MnO 3 ) 2n , n=1 by high angle annular dark field scanning transmission electron microscopy (HAADF STEM) and electron energy loss spectroscopy (EELS). The combination of atomic-resolution Z-contrast and EELS represents a powerful method to link the atomic and electronic structure of solids with macroscopic properties. All images were obtained along orientations and low magnification one shows an overview of a whole 40-nm thick structure, whereas magnified high-resolution images demonstrate an epitaxial growth of LBMO/LMO superlattice on SrTiO 3 substrate. The SL-substrate interface is coherent and free of defects, but reveals a high level of La diffusion into SrTiO 3 . EELS together with STEM are used for probing of a local chemical composition as well as a local electronic state of transition metals and oxygen. Small modulations in the La and Ba EELS signals, which are corresponded to the LBMO and LMO layers, can be observed. The observed features at the substrate interface as well as the SL periodicity in EELS profiles are

Magnetically controlled space charge capacitance at La{sub 1-x}Sr{sub x}MnO{sub 3}/Sr{sub x}La{sub 1-x}TiO{sub 3} interfaces

Energy Technology Data Exchange (ETDEWEB)

Schmidt, Rainer; Garcia-Barriocanal, Javier; Leon, Carlos; Santamaria, Jacobo [Facultad de Ciencias Fisicas, Dpto. Fisica Aplicada III, Universidad Complutense de Madrid, GFMC (Spain); Unidad Asociada ' ' Laboratorio de Heteroestructuras con Aplicacion en Espintronica' ' , UCM/CSIC, Madrid (Spain); Varela, Maria [Facultad de Ciencias Fisicas, Dpto. Fisica Aplicada III, Universidad Complutense de Madrid, GFMC (Spain); Oak Ridge National Laboratory, Oak Ridge, TN (United States); Instituto Pluridisciplinar, Universidad Complutense de Madrid (Spain); Garcia-Hernandez, Mar [Instituto de Ciencia de Materiales de Madrid - Consejo Superior de Investigaciones Cientificas (ICMM-CSIC), Madrid (Spain)

2016-08-15

This work reports on magnetocapacitance (MC) effects in epitaxial heterostructures of nominally 15 unit cells (u.c.) LaMnO{sub 3} (LMO) and 2 u.c. SrTiO{sub 3} (STO) with an alternating layer-repetition rate of 8: (LMO{sub 15}/STO{sub 2}){sub 8}. Epitaxial multilayer growth at high temperatures (900 C) activates a selective inter-diffusion of La{sup 3+} and Sr{sup 2+} cations across the interfaces, which gives rise to Sr p-doping of the LMO and La n-doping of the STO layers. MC effects at the buried La{sub 1-x}Sr{sub x}MnO{sub 3}/Sr{sub x}La{sub 1-x}TiO{sub 3} (LSMO/SLTO) interfaces are probed by frequency, temperature and magnetic field dependent AC impedance spectroscopy. The technique is shown to be appropriate to account for the separate analysis of different resistance and capacitance contributions at the buried interfaces. As a result of the La/Sr inter-diffusion process, Schottky barriers are formed at the LSMO/SLTO interfaces, which give rise to massive MC of up to ∼ -200% in the out-of-plane film direction. The capacitance of the manganite-titanate LSMO/SLTO interfaces may be coupled indirectly to the resistance of the LSMO layers, because the Schottky space-charge layers and their capacitance can be modulated by varying the concentration of highly mobile charge carriers in the LSMO with a magnetic field. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

A new, high energy rechargeable lithium ion battery with a surface-treated Li{sub 1.2}Mn{sub 0.54}Ni{sub 0.13}Co{sub 0.13}O{sub 2} cathode and a nano-structured Li{sub 4}Ti{sub 5}O{sub 12} anode

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiaoyu; Huang, Tao; Yu, Aishui, E-mail: asyu@fudan.edu.cn

2015-11-05

Through elaborate design, a new rechargeable lithium ion battery has been developed by comprising a surface-treated Li{sub 1.2}Mn{sub 0.54}Ni{sub 0.13}Co{sub 0.13}O{sub 2} cathode and a nano-structured Li{sub 4}Ti{sub 5}O{sub 12} anode. After precondition Na{sub 2}S{sub 2}O{sub 8} treatment, the initial coulombic efficiency of Li{sub 1.2}Mn{sub 0.54}Ni{sub 0.13}Co{sub 0.13}O{sub 2} cathode has been significantly increased and can be compatible with that of the nano-structured Li{sub 4}Ti{sub 5}O{sub 12} anode. The optimization of structure and morphology for both active electrode materials result in their remarkable electrochemical performances in respective lithium half-cells. Ultimately, the rechargeable lithium ion full battery consisting of both electrodes delivers a specific capacity of 99.0 mAh g{sup −1} and a practical energy density of 201 Wh kg{sup −1}, based on the total weight of both active electrode materials. Furthermore, as a promising candidate in the lithium ion battery field, this full battery also achieves highly attractive electrochemical performance with high coulombic efficiency, excellent cycling stability and outstanding rate capability. Thus the proposed battery displays broad practical application prospects for next generation of high-energy lithium ion battery. - Highlights: • The Li{sub 1.2}Mn{sub 0.54}Ni{sub 0.13}Co{sub 0.13}O{sub 2} cathode is surface-treated by Na{sub 2}S{sub 2}O{sub 8}. • The nano-sized Li{sub 4}Ti{sub 5}O{sub 12} anode is obtained by a solid-state method. • A new Li{sub 1.2}Mn{sub 0.54}Ni{sub 0.13}Co{sub 0.13}O{sub 2}/Li{sub 4}Ti{sub 5}O{sub 12} lithium ion battery is developed. • The battery shows high coulombic efficiency, specific capacity and energy density. • The battery shows high capacity retention rate and good high-rate capability.

Substrate-induced dielectric polarization in thin films of lead-free (Sr{sub 0.5}Bi{sub 0.5}){sub 2}Mn{sub 2-x}Ti{sub x}O{sub 6-δ} perovskites grown by pulsed laser deposition

Energy Technology Data Exchange (ETDEWEB)

Álvarez-Serrano, I., E-mail: ias@ucm.es [Dpto. Química Inorgánica I, Facultad de Ciencias Químicas, Universidad Complutense, 28040 Madrid (Spain); Ruiz de Larramendi, I. [Dpto. Química Inorgánica, Facultad de Ciencia y Tecnología, Universidad del País Vasco UPV/EHU, 48080 Bilbao (Spain); López, M.L.; Veiga, M.L. [Dpto. Química Inorgánica I, Facultad de Ciencias Químicas, Universidad Complutense, 28040 Madrid (Spain)

2017-03-31

Highlights: • Highly oriented SrBiMn{sub 2-x}Ti{sub x}O{sub 6} thin films are successfully fabricated by PLD. • Thicknesses between 80 and 900 nm depending on x, substrate-type and chamber pressure. • Compositional A-segregation controlled by the STO substrate orientation. • Dielectric response analyzed under impedance and modulus formalisms. • Relaxor phenomena obtained related to NPRs formation and compositional scenario. - Abstract: Thin films of SrBiMn{sub 2-x}Ti{sub x}O{sub 6-δ} have been fabricated by Pulsed Laser Deposition on SrTiO{sub 3} [100] and [111] substrates. Their texture, width, homogeneity and morphology are evaluated by means of XRD, SEM, XPS, whereas complex impedance spectroscopy is employed to analyze their electrical response. The thickness values range between 80 and 900 nm depending on the experimental conditions. The epitaxial growing could be interpreted in terms of two contributions of microstructural origin: a matrix part and some polycrystalline surface formations (hemi-spheres). Texture studies suggest a fiber-type orientated morphology coherently with the Scanning Electron Microscopy images. XPS analyses indicate a segregation regarding A-sublattice cations, which features depend on the substrate orientation. This segregation could be connected to the development of nanopolar regions. Impedance data show the electrical polarization in the samples to be enhanced compared to bulk response of corresponding powdered samples. A relaxor behavior which fits a Vogel-Fulcher law is obtained for x = 0.50 whereas an almost frequency-independent relaxor ferroelectric behavior is registered for the thinnest film of x = 0.25 composition grown on SrTiO{sub 3} [111] substrate. The influence of compositional and structural aspects in the obtained dielectric response is analyzed.

Chemical solution deposition of LaMnO3-based films for coated conductors

International Nuclear Information System (INIS)

Shi, D Q; Zhu, X B; Kim, J H; Wang, L; Zeng, R; Dou, S X; Lei, H C; Sun, Y P

2008-01-01

LaMnO 3 -based films were prepared using the chemical solution deposition method. It was found that the films on perovskite oxide single crystal substrates are highly (h00)-oriented when the annealing atmosphere is oxygen or air; however, when the substrate is yttrium-stabilized ZrO 2 , only the La 1-x Na x MnO 3 films are highly (h00)-oriented, and other LaMnO 3 -based films are (110)-oriented. Under a reducing annealing atmosphere, the atmosphere must be wet in order to create a suitable oxygen partial pressure to crystallize the LaMnO 3 -based films. After annealing under a wet reducing atmosphere the LaMnO 3 -based films are (110)-oriented when the films are directly deposited on Ni tapes; however, when SrTiO 3 -buffered Ni tapes are used, the LaMnO 3 films are (h00)-oriented, which is suitable for subsequent growth of YBCO. The results suggest that it is possible to tune the orientation of buffer layers using suitable templates, which can widen the selection of buffer layers for coated conductors in the all metallorganic deposition approach

Effect of Sr2TiMnO6 fillers on mechanical, dielectric and thermal behaviour of PMMA polymer

Directory of Open Access Journals (Sweden)

P. Thomas

2015-09-01

Full Text Available Composites of poly(methyl methacrylate (PMMA and Sr2TiMnO6 (STMO were fabricated via melt mixing followed by hot pressing technique. These were characterized using X-ray diffraction (XRD, thermo gravimetric analysis (TGA, differential scanning calorimetry (DSC, thermo mechanical analysis (TMA and impedance analyser for their structural, thermal and dielectric properties. The coefficient of thermal expansion (CTE was measured between 40°C and 100°C for pure PMMA is 115.2 ppm/°C, which was decreased to 78.58 ppm/°C when the STMO content was increased to 50 wt.% in PMMA. There was no difference in the glass transition (Tg temperature of the PMMA polymer and their composites. However, the FTIR analysis indicated possible interaction between the PMMA and STMO. The density and the hardness were increased as the STMO content increased in the PMMA matrix. Permittivity was found to be as high as 30.9 at 100 Hz for the PMMA+STMO-50 wt.% composites, indicating the possibility of using these materials for capacitor applications. The thermal stability of polymer was enhanced by incorporation of STMO fillers.

Strain and electric field mediated manipulation of magnetism in La{sub (1-x)}Sr{sub x}MnO{sub 3}/BaTiO{sub 3} heterostructures

Energy Technology Data Exchange (ETDEWEB)

Schmitz, Markus

2016-07-01

Heterostructures of ferromagnetic La{sub 1-x}Sr{sub x}MnO{sub 3} (LSMO) and ferroelectric BaTiO{sub 3} (BTO) were produced and investigated for their structural and magnetic properties. The combination of these ferroic properties can lead to an artificial multiferroic. Special emphasis was given to the manipulation of magnetic properties by applying electric fields. A magneto-electric coupling could be observed in the heterostructures under investigation. Epitaxial LSMO thin films were grown on BTO substrates using a state-of-the-art oxide molecular beam epitaxy (OMBE) and a high oxygen sputtering system (HOPSS). Stoichiometric La{sub 1-x}Sr{sub x}MnO{sub 3} films with doping levels of x=0.5 and x=0.3 were produced. The film quality in terms of roughness and crystalline structure was confirmed by X-ray scattering methods. The presence of structural domains in the BaTiO{sub 3} single crystal substrate, whose proportion could be altered due to the application of electric fields, was shown by X-ray diffraction. Tensile strain is induced into the epitaxial La{sub 1-x}Sr{sub x}MnO{sub 3} films in the whole temperature range under investigation. The magnetization of LSMO alteres by the variation of strain induced into the film, generated by the different structural phases of single crystal BaTiO{sub 3} substrates. The magnetization shows sharp steps at the structural phase transition temperatures of BTO. The evaluation of magnetic hysteresis loops reveals a change of the magnetic anisotropy of LSMO for each structural phase of BTO, but also within the orthorhombic phase. Special focus was given to the manipulation of magnetic properties by the application of electric fields. A newly established measurement option was used to determine the magnetic response to an applied electric field as a function of temperature and magnetic field. The electrically induced modification of the magnetization is profound near the structural phase transition temperatures. Electrical

Growth and electrical properties of (Mn,F) co-doped 0.92Pb(Zn 1/3Nb 2/3)O 3-0.08PbTiO 3 single crystal

Science.gov (United States)

Zhang, Shujun; Lebrun, Laurent; Randall, Clive A.; Shrout, Thomas R.

2004-06-01

The growth and characterization of (Mn,F) doped Pb(Zn 1/3Nb 2/3)O 3-PbTiO 3 (PZNT) single crystals are reported in this paper. The typical single crystal obtained is up to 30 mm size with dark brown color. The crystal lattice parameters of doped PZNT crystal are slightly decreased compared to the pure one. The room temperature dielectric permittivity along direction is about 6000, which is lower than that of the pure PZNT8 because of the dopants. The Curie temperature of the doped crystal is about 180°C while the ferroelectric phase transition temperature is around 100°C, which are higher than those of the pure PZNT8 single crystal. The remnant polarization and coercive field of oriented doped crystal measured at 1 Hz and 10 kV/cm field are about 27 μC/cm 2 and 4.2 kV/cm, respectively. The room temperature mechanical quality factor is ˜300. Piezoelectric coefficient of oriented doped crystal is higher than 3500 pC/N and the longitudinal electromechanical coupling factor is larger than 93%. The piezoelectric properties of doped PZNT single crystal with temperature and orientations are also reported in this paper. The valence state of the manganese dopant was determined by electron spin resonance, indicating no Mn 4+ in the crystals, suggesting the valence of manganese ions in PZNT crystals may be 2+, which acts as a hardener, stabilizes the domain wall and pins the domain wall motion, on the other hand, the dopant will enter Ti 4+ position, shifting the crystal composition to higher PT content.

Microstructure, Piezoelectric, and Ferroelectric Properties of BZT-Modified BiFeO3-BaTiO3 Multiferroic Ceramics with MnO2 and CuO Addition

Science.gov (United States)

Guan, Shibo; Yang, Huabin; Chen, Guangcong; Zhang, Rui

2018-02-01

A new lead-free piezoelectric ceramic, 0.67BiFeO3-0.33BaTiO3-xBi(Zn0.5Ti0.5) O3 + 0.0035MnO2 + 0.004CuO, was prepared through the solid-state reaction route. The ceramic was sintered in the 950-990°C range. In this paper, the crystal structure of the sample is pure perovskite structure with a pseudo-cubic structure in the range of x = 0-0.05, and does not change greatly with the increase of x. The grain size increases first and then decreases with the increase of x. The addition of Bi(Zn0.5Ti0.5) O3(BZT) promoted the grain growth of the sample. The piezoelectric constant reached the maximum value of d 33 = 188 pC/N, electromechanical coupling coefficient k p = 0.301 and the remanent polarization P r = 61.20 μC/cm2 at x = 0.03. It has a high Curie temperature of T c = 420°C. On the other hand, the depolarization temperature reaches the maximum value, T d = 426°C, at x = 0. A small amount of BZT doping can improve the piezoelectric, dielectric, and ferroelectric properties of the samples. Therefore, this material can be considered as a promising lead-free piezoelectric ceramic material in the application field of high-temperature materials.

Anisotropic strains and magnetoresistance of La0.7Ca0.3MnO3

International Nuclear Information System (INIS)

Koo, T.Y.; Park, S.H.; Lee, K.; Jeong, Y.H.

1997-01-01

Thin films of perovskite manganite La 0.7 Ca 0.3 MnO 3 were grown epitaxially on SrTiO 3 (100), MgO(100) and LaAlO 3 (100) substrates by the pulsed laser deposition method. Microscopic structures of these thin film samples as well as a bulk sample were fully determined by x-ray diffraction measurements. The unit cells of the three films have different shapes, i.e., contracted tetragonal, cubic, and elongated tetragonal for SrTiO 3 , MgO, and LaAlO 3 , respectively, while the unit cell of the bulk is cubic. It is found that the samples with a cubic unit cell show smaller peak magnetoresistance at low fields (approx-lt 1T) than the noncubic ones do. The present result demonstrates that the magnetoresistance of La 0.7 Ca 0.3 MnO 3 at low fields can be controlled by lattice distortion via externally imposed strains. copyright 1997 American Institute of Physics

Ultrasonic Transducer Fabricated Using Lead-Free BFO-BTO+Mn Piezoelectric 1-3 Composite

Directory of Open Access Journals (Sweden)

Yan Chen

2015-05-01

Full Text Available Mn-doped 0.7BiFeO3-0.3BaTiO3 (BFO-0.3BTO+Mn 1% mol lead-free piezoelectric ceramic were fabricated by traditional solid state reaction. The phase structure, microstructure, and ferroelectric properties were investigated. Additionally, lead-free 1–3 composites with 60% volume fraction of BFO-BTO+Mn ceramic were fabricated for ultrasonic transducer applications by a conventional dice-and-fill method. The BFO-BTO+Mn 1-3 composite has a higher electromechanical coupling coefficient (kt = 46.4% and lower acoustic impedance (Za ~ 18 MRayls compared with that of the ceramic. Based on this, lead-free piezoelectric ceramic composite, single element ultrasonic transducer with a center frequency of 2.54 MHz has been fabricated and characterized. The single element transducer exhibits good performance with a broad bandwidth of 53%. The insertion loss of the transducer was about 33.5 dB.

Effect of Mn doped-titania on the activity of metallocene catalyst by in situ ethylene polymerization

KAUST Repository

Abdul Kaleel, S. H.; Bahuleyan, Bijal Kottukkal; De, Sadhankumar; Jabarulla Khan, Masihullah; Sougrat, Rachid; Al-Harthi, Mamdouh Ahmed

2012-01-01

Ethylene polymerization was carried out using highly active metallocene catalysts (Cp 2ZrCl 2 and Cp 2TiCl 2) in combination with methylalumoxane. Titanium(IV) oxide containing 1% Mn as dopant was used as nanofillers. The influence of filler

Characterization and electrochemical performance of lithium-active titanium dioxide inlaid LiNi{sub 0.5}Co{sub 0.2}Mn{sub 0.3}O{sub 2} material prepared by lithium residue-assisted method

Energy Technology Data Exchange (ETDEWEB)

Li, Lingjun [School of Physics and Electronic Science, Changsha University of Science and Technology, Changsha 410114 (China); Department of Mechanical and Biomedical Engineering, City University of Hong Kong, 83 Tat Chee Avenue, Kowloon (Hong Kong); Chen, Zhaoyong, E-mail: csullj@hotmail.com [School of Physics and Electronic Science, Changsha University of Science and Technology, Changsha 410114 (China); Song, Liubin [Hunan Provincial Key Laboratory of Materials Protection for Electric Power and Transportation, School of Chemistry and Biological Engineering, Changsha University of Science and Technology, Changsha 410004, Hunan (China); Xu, Ming; Zhu, Huali; Gong, Li [School of Physics and Electronic Science, Changsha University of Science and Technology, Changsha 410114 (China); Zhang, Kaili, E-mail: kaizhang@cityu.edu.hk [Department of Mechanical and Biomedical Engineering, City University of Hong Kong, 83 Tat Chee Avenue, Kowloon (Hong Kong)

2015-07-25

Highlights: • LiTiO{sub 2}-inlaid LiNi{sub 0.5}Co{sub 0.2}Mn{sub 0.3}O{sub 2} is prepared by lithium residue-assisted method. • The unique inlaid architecture inherits the advantages of coating and doping. • LiTiO{sub 2} inlaying enhances the pristine at high cyclability and rate properties. • Excess LiTiO{sub 2} modification results in low Li{sup +} diffusion coefficient. • The 3 mol% LiTiO{sub 2} inlaid sample exhibits the best electrochemical performance. - Abstract: The lithium residues are consumed as raw materials to in-situ synthesize the LiTiO{sub 2}-inlaid LiNi{sub 0.5}Co{sub 0.2}Mn{sub 0.3}O{sub 2} composites. The effects of various LiTiO{sub 2} contents on the morphology, structure, and electrochemical properties of LiNi{sub 0.5}Co{sub 0.2}Mn{sub 0.3}O{sub 2} materials are investigated in detail. Energy dispersive spectrometer mapping, high-resolution transmission electron microscopy and fast Fourier transform analysis confirm that the spherical particles of LiNi{sub 0.5}Co{sub 0.2}Mn{sub 0.3}O{sub 2} are completely coated by crystalline LiTiO{sub 2} phase; X-ray diffraction, cross-section SEM and corresponding EDS results indicate that Ti ions are also doped into the bulk LiNi{sub 0.5}Co{sub 0.2}Mn{sub 0.3}O{sub 2} with gradient distribution. Electrochemical tests show that the LiTiO{sub 2}-inlaid samples exhibit excellent reversible capacity, enhanced cyclability, superior lithium diffusion coefficient and rate properties. Specially, the 3 mol% LiTiO{sub 2} inlaid sample maintains 153.7 mA h g{sup −1} with 94.4% capacity retention after 100 cycles between 2.7–4.4 V at 1 C, take 30% advantage than that of the pristine one (118.2 mA h g{sup −1}). This improvement can be attributed to the removal of lithium residues and suitable LiTiO{sub 2} inlaying. The absence of lithium residue is helpful to retard the decomposition of LiPF{sub 6}. While, suitable LiTiO{sub 2} inlaying can protect the bulk from directly contacting the electrolyte

Structural and functional properties of La1-xBaxMnO3 thin films on SrTiO3

International Nuclear Information System (INIS)

Belenchuk, A.; Kantser, V.; Shapoval, O.; Zasavitsky, E.; Moshnyaga, V.

2011-01-01

Full text: Colossal magneto resistive manganites such as La 1-x Ba x MnO3 (LBMO) show a reach diversity of a attractive physical properties and the epitaxy of manganites has figured conspicuously in the search for new generations of electronic materials for information processing, data storage, and sensing. All applications require manganite films with a smooth morphology and perfect functional properties such as a large magnetization and a small residual resistivity. We investigated the structural and functional properties of the epitaxial LBMO thin films grown on the near perfect matched SrTiO 3 substrates by metalorganic aerosol deposition technique. AFM surface analysis shows a very smooth films surface indicating the layer-by-layer growth mode. The occurrence of a distinct Laue thickness fringes in X-ray diffraction spectra indicates a high quality single-crystalline growth of an uniformly strained LBMO films. But the small-angle x-ray scattering reveals the presence of a few unit cells intermediate layer with a modified electronic density. Transport measurements determine a high metal-insulator transition temperature (T MI >340 K) confirming near optimal Ba doping of LBMO with the residual resistivity of 350 μΩcm at 50 K. According to the inductive coupled plasma emission spectroscopy analysis the LBMO has level of Ba doping x=0.32. However, SQUID magnetization measurements reveal the coexistence of a high Curie temperature (T C =335 K) and a low coercitive field (27-30 Oe) with a reduced saturation magnetization (∼3 μ B /Mn) and broadened para-ferromagnetic transition. The presence of magnetic phase inhomogeneity can be further revealed from the form of low-temperature magnetization loops. We discuss the results within the concept of a 'hidden' magnetic layer situated close to the film-substrate interface and the presence of magnetic phase separation phenomenon in the main part of the LBMO film. (authors)

Effects of MnO{sub 2} doping on structure, dielectric and piezoelectric properties of 0.825NaNbO{sub 3}-0.175Ba{sub 0.6}(Bi{sub 0.5}K{sub 0.5}){sub 0.4}TiO{sub 3} lead-free ceramics

Energy Technology Data Exchange (ETDEWEB)

Fan, Ximing; Lin, Dunmin; Zheng, Qiaoji; Sun, Hailing; Wan, Yang; Wu, Xiaochun [College of Chemistry and Materials Science, and Visual Computing and Virtual Reality Key Laboratory of Sichuan Province, Sichuan Normal University, Chengdu 610066 (China); Wu, Lang [State Key Laboratory Cultivation Base for Nonmetal Composites and Functional Materials, Southwest University of Science and Technology, Mianyang 621010 (China)

2012-12-15

Lead-free ceramics 0.825NaNbO{sub 3}-0.175Ba{sub 0.6}(Bi{sub 0.5}K{sub 0.5}){sub 0.4}TiO{sub 3} + xmol% MnO{sub 2} were prepared by an ordinary sintering technique and the effects of MnO{sub 2} doping on the structure, dielectric, and piezoelectric properties of the ceramics were studied. The ceramics with perovskite structure are transformed from tetragonal to pseudocubic phases by increasing the doping level of MnO{sub 2}. After the addition of MnO{sub 2}, the Curie temperature T{sub C} of the ceramics decreases and the ferroelectric-paraelectric phase transition at T{sub C} becomes more diffusive. Because of the donor and acceptor doping effects of Mn ions simultaneously, the piezoelectric constant d{sub 33}, electromechanical coupling coefficient k{sub p}, relative permittivity {epsilon}{sub r}, and mechanical quality factor Q{sub m} are enhanced considerably after the addition of 1 mol% MnO{sub 2}. The ceramic with 1 mol% MnO{sub 2} doping possesses the optimum piezoelectricity (d{sub 33} = 131 pC/N and k{sub p} = 21.8%) and relatively high Q{sub m} = 627. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Synthesis and electrochemistry of cubic rocksalt Li-Ni-Ti-O compounds in the phase diagram of LiNiO{sub 2}-LiTiO{sub 2}-Li[Li{sub 1/3}Ti{sub 2/3}]O{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Lianqi; Noguchi, Hideyuki; Li, Decheng; Muta, Takahisa; Wang, Xiaoqing; Yoshio, Masaki [Department of Applied Chemistry, Saga University, Saga 840-8052 (Japan); Taniguchi, Izumi [Department of Chemical Engineering, Tokyo Institute of Technology, 12-1, Ookayama-2, Meguro-ku, Tokyo 152-8552 (Japan)

2008-10-15

On the basis of extreme similarity between the triangle phase diagrams of LiNiO{sub 2}-LiTiO{sub 2}-Li[Li{sub 1/3}Ti{sub 2/3}]O{sub 2} and LiNiO{sub 2}-LiMnO{sub 2}-Li[Li{sub 1/3}Mn{sub 2/3}]O{sub 2}, new Li-Ni-Ti-O series with a nominal composition of Li{sub 1+z/3}Ni{sub 1/2-z/2}Ti{sub 1/2+z/6}O{sub 2} (0 {<=} z {<=} 0.5) was designed and attempted to prepare via a spray-drying method. XRD identified that new Li-Ni-Ti-O compounds had cubic rocksalt structure, in which Li, Ni and Ti were evenly distributed on the octahedral sites in cubic closely packed lattice of oxygen ions. They can be considered as the solid solution between cubic LiNi{sub 1/2}Ti{sub 1/2}O{sub 2} and Li[Li{sub 1/3}Ti{sub 2/3}]O{sub 2} (high temperature form). Charge-discharge tests showed that Li-Ni-Ti-O compounds with appropriate compositions could display a considerable capacity (more than 80 mAh g{sup -1} for 0.2 {<=} z {<=} 0.27) at room temperature in the voltage range of 4.5-2.5 V and good electrochemical properties within respect to capacity (more than 150 mAh g{sup -1} for 0 {<=} z {<=} 0.27), cycleability and rate capability at an elevated temperature of 50 C. These suggest that the disordered cubic structure in some cases may function as a good host structure for intercalation/deintercalation of Li{sup +}. A preliminary electrochemical comparison between Li{sub 1+z/3}Ni{sub 1/2-z/2}Ti{sub 1/2+z/6}O{sub 2} (0 {<=} z {<=} 0.5) and Li{sub 6/5}Ni{sub 2/5}Ti{sub 2/5}O{sub 2} indicated that charge-discharge mechanism based on Ni redox at the voltage of >3.0 V behaved somewhat differently, that is, Ni could be reduced to +2 in Li{sub 1+z/3}Ni{sub 1/2-z/2}Ti{sub 1/2+z/6}O{sub 2} while +3 in Li{sub 6/5}Ni{sub 2/5}Ti{sub 2/5}O{sub 2}. Reduction of Ti{sup 4+} at a plateau of around 2.3 V could be clearly detected in Li{sub 1+z/3}Ni{sub 1/2-z/2}Ti{sub 1/2+z/6}O{sub 2} with 0.27 {<=} z {<=} 0.5 at 50 C after a deep charge associated with charge compensation from oxygen ion during initial cycle

Nanostructured Networks for Energy Storage: Vertically Aligned Carbon Nanotubes (VACNT as Current Collectors for High-Power Li4Ti5O12(LTO//LiMn2O4(LMO Lithium-Ion Batteries

Directory of Open Access Journals (Sweden)

Fabian Pawlitzek

2017-11-01

Full Text Available As a concept for electrode architecture in high power lithium ion batteries, self-supported nanoarrays enable ultra-high power densities as a result of their open pore geometry, which results in short and direct Li+-ion and electron pathways. Vertically aligned carbon nanotubes (VACNT on metallic current collectors with low interface resistance are used as current collectors for the chemical solution infiltration of electroactive oxides to produce vertically aligned carbon nanotubes decorated with in situ grown LiMn2O4 (LMO and Li4Ti5O12 (LTO nanoparticles. The production processes steps (catalyst coating, VACNT chemical vapor deposition (CVD, infiltration, and thermal transformation are all scalable, continuous, and suitable for niche market production to achieve high oxide loadings up to 70 wt %. Due to their unique transport structure, as-prepared nanoarrays achieve remarkably high power densities up to 2.58 kW kg−1, which is based on the total electrode mass at 80 C for LiMn2O4//Li4Ti5O12 full cells. The tailoring of LTO and LMO nanoparticle size (~20–100 nm and VACNT length (array height: 60–200 µm gives insights into the rate-limiting steps at high current for these kinds of nanoarray electrodes at very high C-rates of up to 200 C. The results reveal the critical structural parameters for achieving high power densities in VACNT nanoarray full cells.

Studies on compensating valency substituted BaTi (Mnx/2Nbx/2O3 ...

Indian Academy of Sciences (India)

Studies on compensating valency substituted BaTi(1-)Mn/2Nb/2O3 ceramics ... Annealing is observed to improve quality factor `' of the materials with a ... material engineering efforts are required to improve the material properties.

Density functional study of the stability and magnetic behaviour of Au{sub n}TM{sup +} clusters (TM=Au,Sc,Ti,V,Cr,Mn,Fe; 1{<=}n{<=}9)

Energy Technology Data Exchange (ETDEWEB)

Torres, M.B. [Dpto. de Matematicas y Computacion, Univ. de Burgos, Avda. de Cantabria s/n, 09006-Burgos (Spain); Fernandez, E.M.; Balbas, L.C. [Dpto. de Fisica Teorica, Univ. de Valladolid, Prado de la Magdalena s/n, 47011-Valladolid (Spain)

2005-03-01

We study the element- and size-dependent electron stability of Au{sub n}TM{sup +} clusters (TM=Sc,Ti,V,Cr,Mn,Fe,Au; 1{<=}n{<=}9) by means of first-principles density functional calculations. The interplay between the cluster atomic arrangements and their electronic and magnetic structure is investigated for the few lower energy isomeric-states in dependence of the TM-atom and its environment in the cluster. We explain the experimental magic-numbers, observed recently, as well as the trend of the impurity local magnetic moment in dependence with the size of the cluster and the position of the impurity in the host. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Amorphous nanosized Al–Ti–Mn trimetal hydrous oxides: synthesis, characterization and enhanced performance in arsenic removal

Czech Academy of Sciences Publication Activity Database

Thanh, D. N.; Bastl, Zdeněk; Černá, K.; Ulbrich, P.; Lederer, J.

2016-01-01

Roč. 6, č. 103 (2016), s. 100732-100742 ISSN 2046-2069 Institutional support: RVO:61388955 Keywords : RAY PHOTOELECTRON-SPECTROSCOPY * BINARY MIXED-OXIDE * Al-Ti-Mn trimetal hydrous oxides * AQUEOUS-SOLUTION Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.108, year: 2016

Initial oxidation of TiFe1−xMnx (x = 0–0.3) by low dose exposures to H2O and O2

International Nuclear Information System (INIS)

Shwartz, A.; Shamir, N.; Froumin, N.; Zalkind, S.; Edry, I.; Haim, A.; Mintz, M.H.

2014-01-01

Highlights: • Thermodynamics of adsorption and initial oxidation of TiFe 1−x Mn x by H 2 O versus O 2 . • Explanation of different oxide formations. • Explanation of the role of the different constituents of the alloys in the processes. - Abstract: The very initial room-temperature oxidation processes of the ternary pseudo-binary TiFe 1−x Mn x (x = 0–0.3) intermetallics by trace amounts of H 2 O vapor and O 2 were studied utilizing XPS and AES techniques. Different reactivities of the two gases were obtained, with a lower oxidation ability of H 2 O, relative to O 2 , as anticipated from thermodynamic considerations. The exposure to O 2 results in a two stage oxidation of the Ti ingredient, which first converts into a divalent TiO (up to exposures of about 2 L), then proceeds into a tetravalent TiO 2 form. Unlike oxygen, water exposure produces only the divalent oxide through the whole exposure range studied (11 L). The Mn component in these compounds is oxidized only by O 2 and not by H 2 O. The Fe ingredient is not oxidized at all and remains in its metallic form up to exposures of 30 L

Natural CaO-TiO2-SiO2 based ceramics

Directory of Open Access Journals (Sweden)

Jelena Pantić

2011-06-01

Full Text Available Lešnica river deposits consist of a large number of minerals of different grain sizes including sphene. Since it is very difficult to obtain pure monophase titanite by different synthetic routes (sol-gel, coprecipitation, combustion, spray pyrolysis and hydrothermal method, the aim of this work was to study the structure of the sphene from the Lešnica river deposits and possibility of using it as a natural precursor for CaO-TiO2-SiO2 based ceramics. The sphene from Lešnica was analyzed by different methods: tristimulus colorimetry, infrared spectroscopy, electron microprobe and X-ray single crystal diffraction. It was confirmed that Al, Fe, Mn and P are present in the sphene structure and proposed that corresponding structural formula could be: (Ca2+1.008 Mn2+0.0021.010(Ti4+0.901 Fe3+0.033 Al3+0.060 P5+0.0010.995 Si4+1.024 O2-5.

Hierarchically Structured Co3O4@Pt@MnO2 Nanowire Arrays for High-Performance Supercapacitors

Science.gov (United States)

Xia, Hui; Zhu, Dongdong; Luo, Zhentao; Yu, Yue; Shi, Xiaoqin; Yuan, Guoliang; Xie, Jianping

2013-10-01

Here we proposed a novel architectural design of a ternary MnO2-based electrode - a hierarchical Co3O4@Pt@MnO2 core-shell-shell structure, where the complemental features of the three key components (a well-defined Co3O4 nanowire array on the conductive Ti substrate, an ultrathin layer of small Pt nanoparticles, and a thin layer of MnO2 nanoflakes) are strategically combined into a single entity to synergize and construct a high-performance electrode for supercapacitors. Owing to the high conductivity of the well-defined Co3O4 nanowire arrays, in which the conductivity was further enhanced by a thin metal (Pt) coating layer, in combination with the large surface area provided by the small MnO2 nanoflakes, the as-fabricated Co3O4@Pt@MnO2 nanowire arrays have exhibited high specific capacitances, good rate capability, and excellent cycling stability. The architectural design demonstrated in this study provides a new approach to fabricate high-performance MnO2-based nanowire arrays for constructing next-generation supercapacitors.

Structural and magnetic properties of MnCo1-xVxGe compounds

International Nuclear Information System (INIS)

Meng, G.H.; Tegus, O.; Zhang, W.G.; Song, L.; Huang, J.H.

2010-01-01

The structural and magnetic properties of MnCo 1-x V x Ge (x = 0.00, 0.02, 0.04, 0.06, 0.08, 0.10, 0.20 and 0.30) compounds were investigated by means of X-ray diffraction, scanning electron microscopy and magnetization measurements. The MnCo 1-x V x Ge compounds crystallize in the orthorhombic TiNiSi-type crystal structure for x ≤ 0.02 and in the hexagonal Ni 2 In-type structure for x > 0.02. The magnetization measurements show that the MnCo 1-x V x Ge compounds exhibit a complex magnetic behavior. The Curie temperature can be tuned from 360 K to 148 K by increasing x. The maximal magnetic-entropy change is 3.9 J/kg K for x = 0.06 at a field change from 0 to 1.5 T at about 265 K.

First-principles calculations of electronic, magnetic and optical properties of HoN doped with TM (Ti, V, Cr, Mn, Co and Ni)

Science.gov (United States)

Rouchdi, M.; Salmani, E.; Dehmani, M.; Ez-Zahraouy, H.; Hassanain, N.; Benyoussef, A.; Mzerd, A.

2018-02-01

Using the first-principles calculations within the Korringa-Kohn-Rostoker (KKR) method combined with the coherent potential approximation (CPA), the structural, optical and magnetic properties of rare-earth nitride Ho0.95TM0.05N doped with transition metal (TM) atoms (Ti, V, Cr, Mn, Co and Ni) are investigated as a function the generalized gradient approximation and self-interaction correction (GGA-SIC) approximation. The optical properties are studied in detail by using ab-initio calculations. Using GGA-SIC we have showed that the bandgap value is in good agreement with the experimental value. Using GGA-SIC approximation for HoN, we have obtained a bandgap of 0.9 eV. Some of the dilute magnetic semiconductors (DMS) like Ho0.95TM0.05N under study exhibit a half-metallic behavior, which makes them suitable for spintronic applications. Moreover, the optical absorption spectra confirm the ferromagnetic stability based on the charge state of magnetic impurities.

Study of vibrational and rapid local motions of hydrogen in the storage compound Ti0.8 Zr0.2 CrMnH3 by slow neutron scattering

International Nuclear Information System (INIS)

Mestnik Filho, J.

1987-01-01

The vibrational and the rapid local motions of hydrogen in the storage compound Ti 0,8 Zr 0,2 CrMnH 3 have been studied by slow neutron scattering with the beryllium-filter-time-of-flight spectrometer. The form of the density of states of the normal modes of vibrations in host metal does no appear to change on hydrogenation, but a shift of 25% towards lower frequencies has been observed. Debye temperatures for the metal and corresponding hydride have been estimated to be respectively (522 +- 15)K and (311 +- 10)K. An energy distribution consisting of three peeks ∼ 50mev (FWHM) wide corresponding to the energy transfer of 85, 115 and 141mev has been observed and were attributed to hydrogen local vibrations in three types of interstices wich differs in composition of Ti and Zr atoms. In the quasielastic scattering, a broadening of 15μev has been detected for the momentum transfer Q = 2,1(angstrom) -1 and for temperature T= 125 0 C. The broadening has been attributed to rapid local motions of hydrogen in a dumb-bell of lenght equal to the jump lenght for diffusion, l approx. 3(angstrom). (author) [pt

La{sub 0,7}Sr{sub 0,3}MnO{sub 3} thin layers on SrTiO{sub 3}(001) substrate. Structure and Mn valence; La{sub 0,7}Sr{sub 0,3}MnO{sub 3}-Duennschichten auf SrTiO{sub 3}(001)-Substrat. Struktur und Mn-Wertigkeit

Energy Technology Data Exchange (ETDEWEB)

Riedl, Thomas

2007-07-01

This thesis presents a highly spatially resolved characterization of crystal structure and Mn valence by pictures drawn in the TEM and electron-energy-loss ionization edges. The Mn valence determined for the internal od the studied LSMO layers agrees with the nomial value of 3.3, while on some LSMO/STO interfaces between substrate and layers as well as between multilayers a reduction by 0.1..0.2 is to be observed. Furthermore the influence of the interface manifests in the occurence of a shoulder on the side of lower energy loss of the Mn L3 edge. The geometrical phase analysis of HRTEM pictures and TEM bright-field pictures prove a tetragonal strain of th LSMO layer crystals, which consist of needle-shaped twin domains. From highly resolved scanning TEM pictures by electrons scattered under large angle results that the LSMO/STO interface exhibit a coherent lattice structure accidentally provided with elementary-cell stages. Especially the stages (single- or multi-stages) mediate the wavy structure of the LSMO/STO interlayers. Finally it is shown that at low thicknes of the TEM lamella the expected crystal-plane inclination exceeds the expected crystal-plane inclination of the twins. [German] Diese Arbeit stellt eine hoch ortsaufgeloeste Charakterisierung von Kristallstruktur und Mn-Wertigkeit mit im TEM aufgezeichneten Abbildungen und Elektronen-Energieverlust-Ionisationskanten vor. Die fuer das Innere der untersuchten LSMO-Schichten ermittelte Mn-Wertigkeit stimmt mit dem nominalen Wert von 3,3 ueberein, wohingegen an manchen LSMO/STO-Grenzflaechen zwischen Substrat und Schicht sowie zwischen den Schichten von Multilagen eine Reduktion um 0,1...0,2 zu beobachten ist. Weiterhin aeussert sich der Einfluss der Grenzflaeche in dem Auftreten einer Schulter an der Flanke geringeren Energieverlusts der Mn-L3-Kante. Die geometrische Phasenanalyse von HRTEM-Aufnahmen und TEM-Hellfeldaufnahmen belegen eine tetragonale Verzerrung des LSMO-Schichtkristalls, der aus

Diffusion-induced quadrupole relaxation of 27Al nuclei in dilute Al-Ti, Al-Cr, Al-Mn, and Al-Cu alloys at high temperatures

International Nuclear Information System (INIS)

Bottyan, L.; Beke, D.L.; Tompa, K.

1983-01-01

The temperature dependence of the laboratory frame spin-lattice relaxation time of 27 Al nuclei is measured in 5N Al and in dilute Al-Ti, Al-Cr, Al-Mn, and Al-Cu alloys at 5.7 and 9.7 MHz resonance frequencies. The relaxation in pure aluminium is found to be purely due to the conduction electrons. An excess T 1 -relaxation contribution is detected in all Al-3d alloys investigated above 670 K. The excess relaxation rate is proportional to the impurity content and the temperature dependence of the excess contribution is of Arrhenius-type with an activation energy of (1.3 +- 0.3) eV for all of the investigated alloys. The relaxation contribution is found to be quadrupolar in origin and is caused by the relative diffusional jumps of solute atoms and Al atoms relatively far from the impurity. (author)

Study of Ni2-Mn-Ga phase formation by magnetron sputtering film deposition at low temperature onto Si substrates and LaNiO3/Pb(Ti,Zr)O3 buffer

International Nuclear Information System (INIS)

Figueiras, F.; Rauwel, E.; Amaral, V. S.; Vyshatko, N.; Kholkin, A. L.; Soyer, C.; Remiens, D.; Shvartsman, V. V.; Borisov, P.; Kleemann, W.

2010-01-01

Film deposition of Ni 2 MnGa phaselike alloy by radio frequency (rf) magnetron sputtering was performed onto bare Si(100) substrates and LaNiO 3 /Pb(Ti,Zr)O 3 (LNO/PZT) ferroelectric buffer layer near room temperature. The prepared samples were characterized using conventional x-ray diffraction (XRD), superconducting quantum interference device, and electron dispersive x-ray spectroscopy from scanning electron microscope observations. The optimized films deposited under high rf power and low argon pressure present good surface quality and highly textured phase crystallization. The positioning distance between the substrate and the target-holder axis has some limited effect on the film's composition due to the specific diffusion behavior of each element in the sputtering plasma. Extended four pole high resolution XRD analysis allowed one to discriminate the intended Ni-Mn-Ga tetragonal martensitic phase induced by the (100) LNO/PZT oriented buffer. This low temperature process appears to be very promising, allowing separate control of the functional layer's properties, while trying to achieve high electromagnetoelastic coupling.

Efficiency Enhanced Colloidal Mn-Doped Type II Core/Shell ZnSe/CdS Quantum Dot Sensitized Hybrid Solar Cells

Directory of Open Access Journals (Sweden)

A. Jamshidi

2015-01-01

Full Text Available Colloidal Mn-doped ZnSe/CdS core/shell quantum dots (QDs are synthesized for the first time and employed as a strategy to boost the power conversion efficiency of quantum dot sensitized solar cells. By using Mn-doping as a band gap engineering tool for core/shell QDs an effective improvement of absorption spectra could be obtained. The mid-states generated by a proper Mn content alleviate carrier separation and enhance the electron injection rate, thus facilitating electron transport to the TiO2 substrate. It is demonstrated that a device constructed with 0.25% Mn-doped ZnSe/CdS leads to an enhancement of the electron injection rate and power conversion efficiency by 4 times and 1.3, respectively.

La0,7Sr0,3MnO3 thin layers on SrTiO3(001) substrate. Structure and Mn valence

International Nuclear Information System (INIS)

Riedl, Thomas

2007-01-01

This thesis presents a highly spatially resolved characterization of crystal structure and Mn valence by pictures drawn in the TEM and electron-energy-loss ionization edges. The Mn valence determined for the internal od the studied LSMO layers agrees with the nomial value of 3.3, while on some LSMO/STO interfaces between substrate and layers as well as between multilayers a reduction by 0.1..0.2 is to be observed. Furthermore the influence of the interface manifests in the occurence of a shoulder on the side of lower energy loss of the Mn L3 edge. The geometrical phase analysis of HRTEM pictures and TEM bright-field pictures prove a tetragonal strain of th LSMO layer crystals, which consist of needle-shaped twin domains. From highly resolved scanning TEM pictures by electrons scattered under large angle results that the LSMO/STO interface exhibit a coherent lattice structure accidentally provided with elementary-cell stages. Especially the stages (single- or multi-stages) mediate the wavy structure of the LSMO/STO interlayers. Finally it is shown that at low thicknes of the TEM lamella the expected crystal-plane inclination exceeds the expected crystal-plane inclination of the twins [de

Rectifying characteristics and magnetoresistance in La0.9Sr0.1MnO3/Nb-doped SrTiO3 heterojunctions

International Nuclear Information System (INIS)

Luo, Z.; Gao, J.

2007-01-01

Manganite-based heterojunctions have attracted lots of attention as one of the most promising practical applications of colossal magnetoresistance materials. In this work, heterojunctions were fabricated by depositing La 0.9 Sr 0.1 MnO 3 (LSMO) films on substrates of 0.7 wt.% Nb-doped SrTiO 3 using pulsed laser deposition technique. X-ray diffraction spectra confirmed that the grown films are of single phase and have an orientation with the c-axis perpendicular to the substrate surface. As temperature decreases, the resistivity of LSMO films first increases gradually and then increases abruptly at temperature lower than 150 K. These junctions showed clear rectifying characteristics and strong temperature dependent current-voltage relation. Diffusion voltage decreases as temperature increases. Under forward bias, current is proportion to exp(eV/nkT). Ideal factor increases quickly and tunneling current plays more and more important role as temperature decreases. At 50 K, tunneling current becomes nearly dominant. Large magnetoresistance was observed. The sign and value of such magnetoresistance depends on the direction and value of current

Polarization enhancement and ferroelectric switching enabled by interacting magnetic structures in DyMnO3 thin films

KAUST Repository

Lu, Chengliang; Dong, Shuai; Xia, Zhengcai; Luo, Hui; Yan, Zhibo; Wang, Haowen; Tian, Zhaoming; Yuan, Songliu; Wu, Tao; Liu, Junming

2013-01-01

magnetically induced electric polarization and its remarkable response to magnetic field (an enhancement of ?800% upon a field of 2 Tesla at 2 K) in DyMnO3 thin films grown on Nb-SrTiO3 substrates. Accompanying with the large polarization enhancement

Mn bioavailability by polarized Caco-2 cells: comparison between Mn gluconate and Mn oxyprolinate

Directory of Open Access Journals (Sweden)

Fulgenzi Alessandro

2011-07-01

Full Text Available Abstract Background Micronutrient inadequate intake is responsible of pathological deficiencies and there is a need of assessing the effectiveness of metal supplementation, frequently proposed to rebalance poor diets. Manganese (Mn is present in many enzymatic intracellular systems crucial for the regulation of cell metabolism, and is contained in commercially available metal supplements. Methods We compared the effects of two different commercial Mn forms, gluconate (MnGluc and oxyprolinate (MnOxP. For this purpose we used the polarized Caco-2 cells cultured on transwell filters, an established in vitro model of intestinal epithelium. Since micronutrient deficiency may accelerate mitochondrial efficiency, the mitochondrial response of these cells, in the presence of MnGluc and MnOxP, by microscopy methods and by ATP luminescence assay was used. Results In the presence of both MnOxP and MnGluc a sustained mitochondrial activity was shown by mitoTraker labeling (indicative of mitochondrial respiration, but ATP intracellular content remained comparable to untreated cells only in the presence of MnOxP. In addition MnOxP transiently up-regulated the antioxidant enzyme Mn superoxide dismutase more efficiently than MnGluc. Both metal treatments preserved NADH and βNADPH diaphorase oxidative activity, avoided mitochondrial dysfunction, as assessed by the absence of a sustained phosphoERK activation, and were able to maintain cell viability. Conclusions Collectively, our data indicate that MnOxP and MnGluc, and primarily the former, produce a moderate and safe modification of Caco-2 cell metabolism, by activating positive enzymatic mechanisms, thus could contribute to long-term maintenance of cell homeostasis.

La0.8Sr0.2MnO3

KAUST Repository

Wang, Q.; Chen, A. P.; Guo, E. J.; Roldan, M. A.; Jia, Q. X.; Fitzsimmons, M. R.

2018-01-01

Using polarized neutron reflectometry, we measured the influence of elastic bending stress on the magnetization depth profile of a La0.8Sr0.2MnO3 (LSMO) epitaxial film grown on a SrTiO3 substrate. The elastic bending strain of +/- 0.03% has no obvious effect on the magnetization depth profile at saturation. This result is in stark contrast to that of (La1-xPrx)(1-y),Ca-y,MnO3 (LPCMO) films for which strain of +/- 0.01% produced dramatic changes in the magnetization profile and Curie temperature. We attribute the difference between the influence of strain on the saturation magnetization in LSMO (weak or none) and LPCMO (strong) to a difference in the ability of LSMO (weak or none) and LPCMO (strong) to phase separate. Our observation provides an upper limit of tuning LSMO saturation magnetization via elastic strain effect.

Structural and electric properties of La{sub 0.7}Sr{sub 0.25}Na{sub 0.05}Mn{sub 0.9}Ti{sub 0.1}O{sub 3} ceramics

Energy Technology Data Exchange (ETDEWEB)

Kossi, S. EL., E-mail: safwene666@hotmail.com [Laboratoire de la Matiére Condensée et des Nanosciences, Département de Physique, Faculté des Sciences University de Monastir, 5019 (Tunisia); Rhouma, F.I.H. [Laboratoire de la Matiére Condensée et des Nanosciences, Département de Physique, Faculté des Sciences University de Monastir, 5019 (Tunisia); Laboratoire de Photovoltaique, Centre de Recherches et des Tehnologies de l' Energie, BP Hammam-Lif 2050 (Tunisia); Dhahri, J. [Laboratoire de la Matiére Condensée et des Nanosciences, Département de Physique, Faculté des Sciences University de Monastir, 5019 (Tunisia); Khirouni, K. [Laboratoire de Physique des Matériaux et des Nanomatériaux Appliquée à L’environnement, Faculté des Sciences de Gabes Cité Erriadh, 6079 Gabes (Tunisia)

2014-05-01

This work studies structural and various electrical properties of polycrystalline La{sub 0.7}Sr{sub 0.25} Na{sub 0.05} Mn{sub 0.9}Ti{sub 0.1}O{sub 3} (LSNMTi), which were prepared by standard solid state reaction technique. The formation of a single phase rhombohedral structure of the composition was confirmed by the X-ray diffraction study. The electrical behavior of sintered pellets investigated by impedance spectra has shown frequency dependent behavior. Both conductivity and electric modulus formalisms have been used to study the relaxation dynamics of charge carriers. The variation of ac conductivity with frequency at different temperatures obeys the universal Jonscher's power law (σ{sub ac}αw).

Determination of hyperfine fields and atomic ordering in NiMnFeGe exhibiting martensitic transformation

Directory of Open Access Journals (Sweden)

Satuła Dariusz

2015-03-01

Full Text Available The hyperfine fields and atomic ordering in Ni1−xFexMnGe (x = 0.1, 0.2, 0.3 alloys were investigated using X-ray diffraction and Mössbauer spectroscopy at room temperature. The X-ray diffraction measurements show that the samples with x = 0.2, 0.3 crystallized in the hexagonal Ni2In-type of structure, whereas in the sample with x = 0.1, the coexistence of two phases, Ni2In- and orthorhombic TiNiSi-type of structures, were found. The Mössbauer spectra measured with x = 0.2, 0.3 show three doublets with different values of isomer shift (IS and quadrupole splitting (QS related to three different local surroundings of Fe atoms in the hexagonal Ni2In-type structure. It was shown that Fe atoms in the hexagonal Ni2In-type structure of as-cast Ni1−xFexMnGe alloys are preferentially located in Ni sites and small amount of Fe is located in Mn and probably in Ge sites. The spectrum for x = 0.1 shows the doublets in the central part of spectrum and a broad sextet. The doublets originate from the Fe atoms in the paramagnetic state of hexagonal Ni2In-type structure, whereas the sextet results from the Fe atoms in orthorhombic TiNiSi-type structure.

Orientation Control of Interfacial Magnetism at La0.67Sr0.33MnO3/SrTiO3 Interfaces.

Science.gov (United States)

Guo, Er-Jia; Charlton, Timothy; Ambaye, Haile; Desautels, Ryan D; Lee, Ho Nyung; Fitzsimmons, Michael R

2017-06-07

Understanding the magnetism at the interface between a ferromagnet and an insulator is essential because the commonly posited magnetic "dead" layer close to an interface can be problematic in magnetic tunnel junctions. Previously, degradation of the magnetic interface was attributed to charge discontinuity across the interface. Here, the interfacial magnetism was investigated using three identically prepared La 0.67 Sr 0.33 MnO 3 (LSMO) thin films grown on different oriented SrTiO 3 (STO) substrates by polarized neutron reflectometry. In all cases the magnetization at the LSMO/STO interface is larger than the film bulk. We show that the interfacial magnetization is largest across the LSMO/STO interfaces with (001) and (111) orientations, which have the largest net charge discontinuities across the interfaces. In contrast, the magnetization of LSMO/STO across the (110) interface, the orientation with no net charge discontinuity, is the smallest of the three orientations. We show that a magnetically degraded interface is not intrinsic to LSMO/STO heterostructures. The approach to use different crystallographic orientations provides a means to investigate the influence of charge discontinuity on the interfacial magnetization.

Processing and characterization of AlCoFeNiXTi0,5 (X = Mn, V) high entropy alloys

International Nuclear Information System (INIS)

Triveno Rios, C.; Kiminami, C.S.

2014-01-01

The microstructure of high entropy alloys consists of solid solution phases with FC and BCC simple structures, contrary to classical metallurgy where they form complex structures of intermetallic compounds. Because of this they have several attractive properties for engineering applications. In this work the AlCoFeNiMnTi 0,5 and AlCoFeNiVTi 0,5 alloys were processed by melting arc. Since the main objective was the microstructural and mechanical characterization of ingots as-cast. The alloys were characterized by scanning electron microscopy, X-ray diffraction, microhardness and cold compression test. The results showed that the microstructure consists mainly of dendrites and interdendritic regions consisting of metastable crystalline phases. It was also observed that the AlCoFeNiVTi 0,5 alloy showed better mechanical properties than the AlCoFeNiMnTi 0,5 alloy. This may be associated with differences in the parameters of formation of simple solid solution phases between the two alloys. (author)

Prediction of possible CaMnO3 modifications using an ab initio minimization data-mining approach.

Science.gov (United States)

Zagorac, Jelena; Zagorac, Dejan; Zarubica, Aleksandra; Schön, J Christian; Djuris, Katarina; Matovic, Branko

2014-10-01

We have performed a crystal structure prediction study of CaMnO3 focusing on structures generated by octahedral tilting according to group-subgroup relations from the ideal perovskite type (Pm\\overline 3 m), which is the aristotype of the experimentally known CaMnO3 compound in the Pnma space group. Furthermore, additional structure candidates have been obtained using data mining. For each of the structure candidates, a local optimization on the ab initio level using density-functional theory (LDA, hybrid B3LYP) and the Hartree--Fock (HF) method was performed, and we find that several of the modifications may be experimentally accessible. In the high-pressure regime, we identify a post-perovskite phase in the CaIrO3 type, not previously observed in CaMnO3. Similarly, calculations at effective negative pressure predict a phase transition from the orthorhombic perovskite to an ilmenite-type (FeTiO3) modification of CaMnO3.

An anti CuO{sub 2}-type metal hydride square net structure in Ln{sub 2}M{sub 2}As{sub 2}H{sub x} (Ln = La or Sm, M = Ti, V, Cr, or Mn)

Energy Technology Data Exchange (ETDEWEB)

Mizoguchi, Hiroshi; Park, SangWon; Hosono, Hideo [Tokyo Institute of Technology, Yokohama (Japan). Materials Research Center for Element Strategy; Hiraka, Haruhiro; Ikeda, Kazutaka; Otomo, Toshiya [High-Energy Accelerator Research Organization (KEK), Tsukuba (Japan). Inst. of Materials Structure Science

2015-03-02

Using a high pressure technique and the strong donating nature of H{sup -}, a new series of tetragonal La{sub 2}Fe{sub 2}Se{sub 2}O{sub 3}-type layered mixed-anion arsenides, Ln{sub 2}M{sub 2}As{sub 2}H{sub x}, was synthesized (Ln=La or Sm, M=Ti, V, Cr, or Mn; x∼3). In these compounds, an unusual M{sub 2}H square net, which has anti CuO{sub 2} square net structures accompanying two As{sup 3-} ions, is sandwiched by (LaH){sub 2} fluorite layers. Notably, strong metal-metal bonding with a distance of 2.80 Aa was confirmed in La{sub 2}Ti{sub 2}As{sub 2}H{sub 2.3}, which has metallic properties. In fact, these compounds are situated near the boundary between salt-like ionic hydrides and transition-metal hydrides with metallic characters.

Growth and magnetic properties of multiferroic LaxBi1-xMnO3 thin films

Science.gov (United States)

Gajek, M.; Bibes, M.; Wyczisk, F.; Varela, M.; Fontcuberta, J.; Barthélémy, A.

2007-05-01

A comparative study of LaxBi1-xMnO3 thin films grown on SrTiO3 substrates is reported. It is shown that these films grow epitaxially in a narrow pressure-temperature range. A detailed structural and compositional characterization of the films is performed within the growth window. The structure and the magnetization of this system are investigated. We find a clear correlation between the magnetization and the unit-cell volume that we ascribe to Bi deficiency and the resultant introduction of a mixed valence on the Mn ions. On these grounds, we show that the reduced magnetization of LaxBi1-xMnO3 thin films compared to the bulk can be explained quantitatively by a simple model, taking into account the deviation from nominal composition and the Goodenough-Kanamori-Anderson rules of magnetic interactions.

Thickness dependent charge transport in ferroelectric BaTiO3 heterojunctions

Science.gov (United States)

Singh, Pooja; Rout, P. K.; Singh, Manju; Rakshit, R. K.; Dogra, Anjana

2015-09-01

We have investigated the effect of ferroelectric barium titanate (BaTiO3) film thickness on the charge transport mechanism in pulsed laser deposited epitaxial metal-ferroelectric semiconductor junctions. The current (I)-voltage (V) measurements across the junctions comprising of 20-500 nm thick BaTiO3 and conducting bottom electrode (Nb: SrTiO3 substrate or La2/3Ca1/3MnO3 buffer layer) demonstrate the space charge limited conduction. Further analysis indicates a reduction in the ratio of free to trapped carriers with increasing thickness in spite of decreasing trap density. Such behaviour arises the deepening of the shallow trap levels (I-V curves implies a bipolar resistive switching behaviour, which can be explained in terms of charge trapping and de-trapping process.

Photocatalytic Degradation of Methyl Orange over Metalloporphyrins Supported on TiO2 Degussa P25

Directory of Open Access Journals (Sweden)

Xing-Jiao Huang

2012-01-01

Full Text Available The photocatalytic activity of meso-tetraphenylporphyrins with different metal centers (Fe, Co, Mn and Cu adsorbed on TiO2 (Degussa P25 surface has been investigated by carrying out the photodegradation of methyl orange (MO under visible and ultraviolet light irradiation. The photocatalysts were characterized by X-ray diffraction (XRD, scanning electron microscopy (SEM, diffuse reflectance UV (DRS-UV-vis and infrared spectra. Copper porphyrin-sensitized TiO2 photocatalyst (CuP-TiO2 showed excellent activity for the photodegradation of MO whether under visible or ultraviolet light irradiation. Natural Bond Orbital (NBO charges analysis showed that methyl orange ion is adsorbed easier by CuP-TiO2 catalyst due to the increase of induced interactions.

Photoresponse in La0.9Hf0.1MnO3/0.05wt%Nb-doped SrTiO3 heteroepitaxial junctions

Science.gov (United States)

Qi, Yaping; Ni, Hao; Zheng, Ming; Zeng, Jiali; Jiang, Yucheng; Gao, Ju

2018-05-01

Excellent photo detectors need to have the rapid response and good repeatability from the requirement of industrial applications. In this paper, transport behavior and opto-response of heterostructures made with La0.9Hf0.1MnO3 and 0.05wt%Nb-doped SrTiO3 were investigated. The heterojunctions exhibited an excellent rectifying feature with very low leakage in a broad temperature region (from 40 to 300 K). These thin films presented persistent and stable photovoltages upon light illumination. Rapid shift between small and large voltages corresponding to "light OFF" and "light ON" states, respectively, was observed, demonstrating reliable photo detection behavior. A semiconductor laser with a wavelength of 650 nm was used as the light source. It is also noted that the observed photovoltages are strongly determined by light intensity. The injection of photoexcited charge carriers (electrons) could be responsible for the appearance of the observed opto-response. Such manipulative features by light irradiation exhibit great potential for light detectors for visible light.

Photoresponse in La0.9Hf0.1MnO3/0.05wt%Nb-doped SrTiO3 heteroepitaxial junctions

Directory of Open Access Journals (Sweden)

Yaping Qi

2018-05-01

Full Text Available Excellent photo detectors need to have the rapid response and good repeatability from the requirement of industrial applications. In this paper, transport behavior and opto-response of heterostructures made with La0.9Hf0.1MnO3 and 0.05wt%Nb-doped SrTiO3 were investigated. The heterojunctions exhibited an excellent rectifying feature with very low leakage in a broad temperature region (from 40 to 300 K. These thin films presented persistent and stable photovoltages upon light illumination. Rapid shift between small and large voltages corresponding to “light OFF” and “light ON” states, respectively, was observed, demonstrating reliable photo detection behavior. A semiconductor laser with a wavelength of 650 nm was used as the light source. It is also noted that the observed photovoltages are strongly determined by light intensity. The injection of photoexcited charge carriers (electrons could be responsible for the appearance of the observed opto-response. Such manipulative features by light irradiation exhibit great potential for light detectors for visible light.

Multilevel Resistance Switching Memory in La2/3Ba1/3MnO3/0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 (011) Heterostructure by Combined Straintronics-Spintronics.

Science.gov (United States)

Zhou, Weiping; Xiong, Yuanqiang; Zhang, Zhengming; Wang, Dunhui; Tan, Weishi; Cao, Qingqi; Qian, Zhenghong; Du, Youwei

2016-03-02

We demonstrate a memory device with multifield switchable multilevel states at room temperature based on the integration of straintronics and spintronics in a La2/3Ba1/3MnO3/0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 (PMN-PT) (011) heterostructure. By precisely controlling the electric field applied on the PMN-PT substrate, multiple nonvolatile resistance states can be generated in La2/3Ba1/3MnO3 films, which can be ascribed to the strain-modulated metal-insulator transition and phase separation of Manganite. Furthermore, because of the strong coupling between spin and charge degrees of freedom, the resistance of the La2/3Ba1/3MnO3 film can be readily modulated by magnetic field over a broad temperature range. Therefore, by combining electroresistance and magnetoresistance effects, multilevel resistance states with excellent retention and endurance properties can be achieved at room temperature with the coactions of electric and magnetic fields. The incorporation of ferroelastic strain and magnetic and resistive properties in memory cells suggests a promising approach for multistate, high-density, and low-power consumption electronic memory devices.

Large tunneling anisotropic magnetoresistance in La0.7Sr0.3MnO3/pentacene/Cu structures prepared on SrTiO3 (110) substrates

Science.gov (United States)

Kamiya, Takeshi; Miyahara, Chihiro; Tada, Hirokazu

2017-01-01

We investigated tunneling anisotropic magnetoresistance (TAMR) at the interface between pentacene and La0.7Sr0.3MnO3 (LSMO) thin films prepared on SrTiO3 (STO) (110) substrates. The dependence of the TAMR ratio on the magnetic field strength was approximately ten times larger than that of the magnetic field angle at a high magnetic field. This large difference in the TAMR ratio is explained by the interface magnetic anisotropy of strain-induced LSMO thin films on a STO (110) substrate, which has an easy axis with an out-of-plane component. We also note that the TAMR owing to out-of-plane magnetization was positive at each angle of the in-plane magnetic field. This result implies that active control of the interface magnetic anisotropy between organic materials and ferromagnetic metals should realize nonvolatile and high-efficiency TAMR devices.

Phase stability and decomposition processes in Ti-Al based intermetallics

Energy Technology Data Exchange (ETDEWEB)

Nakai, Kiyomichi [Department of Materials Science and Engineering, Faculty of Engineering, Ehime University, 3 Bunkyo-cho, Matsuyama 790 (Japan); Ono, Toshiaki [Department of Materials Science and Engineering, Faculty of Engineering, Ehime University, 3 Bunkyo-cho, Matsuyama 790 (Japan); Ohtsubo, Hiroyuki [Department of Materials Science and Engineering, Faculty of Engineering, Ehime University, 3 Bunkyo-cho, Matsuyama 790 (Japan); Ohmori, Yasuya [Department of Materials Science and Engineering, Faculty of Engineering, Ehime University, 3 Bunkyo-cho, Matsuyama 790 (Japan)

1995-02-28

The high-temperature phase equilibria and the phase decomposition of {alpha} and {beta} phases were studied by crystallographic analysis of the solidification microstructures of Ti-48at.%Al and Ti-48at.%Al-2at.%X (X=Mn, Cr, Mo) alloys. The effects on the phase stability of Zr and O atoms penetrating from the specimen surface were also examined for Ti-48at.%Al and Ti-50at.%Al alloys. The third elements Cr and Mo shift the {beta} phase region to higher Al concentrations, and the {beta} phase is ordered to the {beta}{sub 2} phase. The Zr and O atoms stabilize {beta} and {alpha} phases respectively. In the Zr-stabilized {beta} phase, {alpha}{sub 2} laths form with accompanying surface relief, and stacking faults which relax the elastic strain owing to lattice deformation are introduced after formation of {alpha}{sub 2} order domains. Thus shear is thought to operate after the phase transition from {beta} to {alpha}{sub 2} by short-range diffusion. A similar analysis was conducted for the Ti-Al binary system, and the transformation was interpreted from the CCT diagram constructed qualitatively. ((orig.))

Enhanced temperature stability and quality factor with Hf substitution for Sn and MnO2 doping of (Ba0.97Ca0.03(Ti0.96Sn0.04O3 lead-free piezoelectric ceramics with high Curie temperature

Directory of Open Access Journals (Sweden)

Cheng-Che Tsai

2016-12-01

Full Text Available In this work, the process of two-stage modifications for (Ba0.97Ca0.03(Ti0.96Sn0.04-xHfxO3 (BCTS4-100xH100x ceramics was studied. The trade-off composition was obtained by Hf substitution for Sn and MnO2 doping (two-stage modification which improves the temperature stability and piezoelectric properties. The phase structure ratio, microstructure, and dielectric, piezoelectric, ferroelectric, and temperature stability properties were systematically investigated. Results showed that BCTS4-100xH100x piezoelectric ceramics with x=0.035 had a relatively high Curie temperature (TC of about 112 °C, a piezoelectric charge constant (d33 of 313 pC/N, an electromechanical coupling factor (kp of 0.49, a mechanical quality factor (Qm of 122, and a remnant polarization (Pr of 19μC/cm2. In addition, the temperature stability of the resonant frequency (fr, kp, and aging d33 could be tuned via Hf content. Good piezoelectric temperature stability (up to 110 °C was found with x =0.035. BCTS0.5H3.5 + a mol% Mn (BCTSH + a Mn piezoelectric ceramics with a = 2 had a high TC of about 123 °C, kp ∼ 0.39, d33 ∼ 230 pC/N, Qm ∼ 341, and high temperature stability due to the produced oxygen vacancies. This mechanism can be depicted using the complex impedance analysis associated with a valence compensation model on electric properties. Two-stage modification for lead-free (Ba0.97Ca0.03(Ti0.96Sn0.04O3 ceramics suitably adjusts the compositions for applications in piezoelectric motors and actuators.

Biocorrosion investigation of two shape memory nickel based alloys: Ni-Mn-Ga and thin film NiTi.

Science.gov (United States)

Stepan, L L; Levi, D S; Gans, E; Mohanchandra, K P; Ujihara, M; Carman, G P

2007-09-01

Thin film nitinol and single crystal Ni-Mn-Ga represent two new shape memory materials with potential to be used as percutaneously placed implant devices. However, the biocompatibility of these materials has not been adequately assessed. Immersion tests were conducted on both thin film nitinol and single crystal Ni-Mn-Ga in Hank's balanced salt solution at 37 degrees C and pH 7.4. After 12 h, large pits were found on the Ni-Mn-Ga samples while thin film nitinol displayed no signs of corrosion. Further electrochemical tests on thin film nitinol samples revealed breakdown potentials superior to a mechanically polished nitinol disc. These results suggest that passivation or electropolishing of thin film nitinol maybe unnecessary to promote corrosion resistance.

Kinetic Investigations of SiMn Slags From Different Mn Sources

Science.gov (United States)

Kim, Pyunghwa Peace; Tangstad, Merete

2018-03-01

The kinetics of MnO and SiO2 reduction were investigated for Silicomanganese (SiMn) slags using a Thermogravimetric analysis (TGA) between 1773 K and 1923 K (1500 °C and 1650 °C) under CO atmospheric pressure. The charge materials were based on Assmang ore and HC FeMn Slag. Rate models for MnO and SiO2 reduction were applied to describe the metal-producing rates, as shown by the following equations: r_{MnO} = k_{MnO} × A × ( {a_{MnO} - {a_{Mn} }/{K_{T }}} ) r_{{{SiO}2 }} = k_{SiO2} × A × ( {a_{{{SiO}2 }} - {a_{Si} }/{K_{T }}} ). The results show that the choice of raw materials in the charge considerably affected the reduction rate of MnO and SiO2. The highest reduction rate was found to be from charges using HC FeMn slag. The difference in the driving forces was insignificant among the SiMn slags, and the similar slag viscosities could not explain the different reduction rates. Instead, the difference is attributed to small amounts of sulfur and the amount of iron in the charge. In addition, the rate models were applicable to describe the reduction of MnO and SiO2 in SiMn slags.

An anti CuO{sub 2}-type metal hydride square net structure in Ln{sub 2}M{sub 2}As{sub 2}H{sub x} (Ln = La or Sm, M = Ti, V, Cr, or Mn)

Energy Technology Data Exchange (ETDEWEB)

Mizoguchi, Hiroshi; Park, SangWon; Hosono, Hideo [Materials Research Center for Element Strategy, Tokyo Institute of Technology, Yokohama 226-8503 (Japan); Hiraka, Haruhiro; Ikeda, Kazutaka; Otomo, Toshiya [Institute of Materials Structure Science, High-Energy Accelerator Research Organization (KEK), Tsukuba 305-0801 (Japan)

2015-03-02

Using a high pressure technique and the strong donating nature of H{sup -}, a new series of tetragonal La{sub 2}Fe{sub 2}Se{sub 2}O{sub 3}-type layered mixed-anion arsenides, Ln{sub 2}M{sub 2}As{sub 2}H{sub x}, was synthesized (Ln=La or Sm, M=Ti, V, Cr, or Mn; x∼3). In these compounds, an unusual M{sub 2}H square net, which has anti CuO{sub 2} square net structures accompanying two As{sup 3-} ions, is sandwiched by (LaH){sub 2} fluorite layers. Notably, strong metal-metal bonding with a distance of 2.80 Aa was confirmed in La{sub 2}Ti{sub 2}As{sub 2}H{sub 2.3}, which has metallic properties. In fact, these compounds are situated near the boundary between salt-like ionic hydrides and transition-metal hydrides with metallic characters. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Development of medical guide wire of Cu-Al-Mn-base superelastic alloy with functionally graded characteristics.

Science.gov (United States)

Sutou, Yuji; Omori, Toshihiro; Furukawa, Akihisa; Takahashi, Yukinori; Kainuma, Ryosuke; Yamauchi, Kiyoshi; Yamashita, Shuzo; Ishida, Kiyohito

2004-04-15

A new type of medical guide wire with functionally graded hardness from the tip to the end was developed with the use of Cu-Al-Mn-based alloys. The superelasticity (SE) of the Cu-Al-Mn-based alloys in the tip is drastically improved by controlling the grain size, whereas the end of the wire is hardened using bainitic transformation by aging at around 200-400 degrees C. Therefore, the tip of the guide wire shows a superelasticity and its end has high stiffness. This guide wire with functionally graded characteristics shows excellent pushability and torquability, superior to that of the Ni-Ti guide wire. Copyright 2004 Wiley Periodicals, Inc.

Highly corrosive and high strength Cr-Mn series austenite sintered steel, method of manufacturing the same and the usage

International Nuclear Information System (INIS)

Arai, Masahiko; Hirano, Tatsumi; Aono, Yasuhisa; Kato, Takahiko; Kondo, Yasuo; Inagaki, Masatoshi

1998-01-01

The steel of the present invention comprises a highly corrosive and high strength Cr-Mn series austenite sintered steel containing up to 0.1% of C, up to 1% of Si, up to 0.4% of N, from 9 to 25% of (Mn + Ni) within a range of more than 2% and up to 15% of Mn and from 14 to 20% of Cr, and it has an average crystal grain size of 1μm or less and comprises at least 90 vol% of an austenite phase. In addition, the alloy is incorporated with one or more elements of up to 3% of Mo, 1.0% of Ti, up to 2.0% of Zr and up to 1.0% of Nb in an amount of up to 2.0% in total of Ti, Zr and Nb. When these materials are used under the circumstance where materials are generally deteriorated in grain boundaries, since they are excellent in corrosion resistance and strength, remarkable effects can be attained in the improvement of the safety and the reliability of products. In addition, they are applied not only to a reactor core but also to a water-cooled circumstance and a circumstance where hydrogen exists, thereby capable of exhibiting remarkable effects. (T.M.)

Prediction and analysis of the structure of hydrated Mn2+, V2+, Ti3 and Cr3 ions by means of the MD simulation methods

International Nuclear Information System (INIS)

Iglesias, Y.J.

2002-01-01

Classical Molecular dynamics (MD) and hybrid Quantum/Molecular Mechanics-Molecular Dynamics (QM/MM-MD) simulations have been performed to investigate structural properties of Mn(II), V(II), Cr(III) and Ti(III) cations in aqueous solution. The first hydration sphere in QM/MM-MD simulations is treated quantum mechanically, while the rest of the system is described by classical analytical two- and three-body potentials. The results obtained for the first hydration shell from this method are in agreement with experimental data, showing 100 % of 6 fold coordination around the ion in all cases. The results prove that non/additive contributions are mandatory for an accurate description of ion hydration. Within the QM/MM method, the inclusion of a perturbation field describing the remaining system was shown to be an accurate tool for evaluating the first shell structure, and thus to be a good alternative for systems, where the construction of a three-body correction function is difficult or too time-consuming. (author)

On the sintering behaviour of steel bonded TiC-Cr3C2 and TiC-Cr3C2-WC mixed carbides

International Nuclear Information System (INIS)

Stojanov, L.G.; Exner, H.E.

1978-01-01

Powder mixtures of TiC+Cr 3 C 2 and TiC+Cr 3 C 2 + WC were hot pressed to nearly full density. The lattice parameter of the resulting cubic mixed crystal decreases linearly with increasing additions of Cr 3 C 2 and (Cr 3 C 2 +WC 1:1). Microhardness increases with Cr 3 C 2 content up to 20 wt.%. By addition of WC, microhardness is increased further and reaches a maximum value of approx. 38 000 MN/m 2 for 20 wt.% Cr 3 C 2 and 20 wt.% WC. From these solid solutions powder compositions of Ferro-TiC type were produced by milling with 55 wt.% Fe and 0.4 wt.% C. The sintering behaviour of these powders was studied in a vacuum dilatometer. The pronounced increase of shrinkage by Cr 3 C 2 and higher amounts of Cr 3 C 2 +WC dissolved in TiC previous to binder phase melting is attributed to the increased solubility of the carbide in solid iron. Presintering at 700 0 C in hydrogen has a negative influence on sintering activity and requires much higher temperatures for complete densification during subsequent vacuum sintering. (orig.) [de

Promotion of redox and stability features of doped Ce–W–Ti for NH{sub 3}-SCR reaction over a wide temperature range

Energy Technology Data Exchange (ETDEWEB)

Zhao, Kun [State Key Laboratory for Oxo Synthesis and Selective Oxidation, National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Key laboratory of Oil & Gas Fine Chemical, Ministry of Education, College of Chemistry and Chemical Engineering, Xinjiang University, Urumqi 830046 (China); Han, Weiliang; Lu, Gongxuan [State Key Laboratory for Oxo Synthesis and Selective Oxidation, National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Lu, Jiangyin, E-mail: jiangyinlu6410@163.com [Key laboratory of Oil & Gas Fine Chemical, Ministry of Education, College of Chemistry and Chemical Engineering, Xinjiang University, Urumqi 830046 (China); Tang, Zhicheng, E-mail: tangzhicheng@licp.cas.cn [State Key Laboratory for Oxo Synthesis and Selective Oxidation, National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Zhen, Xinping [Key laboratory of Oil & Gas Fine Chemical, Ministry of Education, College of Chemistry and Chemical Engineering, Xinjiang University, Urumqi 830046 (China)

2016-08-30

Graphical abstract: In this study, different transition metals were introduced into Ce–W–Ti catalyst in order to promote the low temperature activity. The Cu/Ce–W–Ti catalyst prepared via a co-precipitation method displayed more excellent performance in the wide temperature range (260–400 °C). - Highlights: • Redox ability of Ce–W–Ti was enhanced by introduction of CuO. • The optimum catalyst provided high activity and broad operation window. • Cu/Ce–W–Ti presents an adequate tolerance to SO{sub 2} and hydrothermal aging. - Abstract: In this study, transition metals Co, Mn, and Cu were introduced into a Ce–W–Ti catalyst to promote low-temperature catalytic activity. Among these metal-modified M/Ce–W–Ti catalysts (M represents Co, Mn, or Cu), the Cu/Ce–W–Ti catalyst with an optimized Cu content of 5 wt.% exhibited more than 90% conversion of nitrogen oxide (NO{sub x}) in the selective catalytic reduction by NH{sub 3} over a wide temperature range (260–400 °C). This catalyst likewise exhibited higher resistance to SO{sub 2} gas and water vapor under severe test conditions. On the basis of the characterization results by powder X-ray diffraction and X-ray photoelectron spectroscopy, we concluded that the superior catalytic properties of the Cu/Ce–W–Ti catalyst could be attributed to the highly dispersed Cu species, which increased the contents of Ce{sup 3+} species and adsorbed oxygen species in the catalysts. In addition, the NH{sub 3} temperature-programmed desorption results demonstrated that the Cu species doped into the Ce–W–Ti catalysts optimized surface acid content.

Comment on 'Pressure-induced changes in transport properties of layered La1.2Ca1.8Mn2O7'

International Nuclear Information System (INIS)

Ganguly, R.; Siruguri, V.; Gopalakrishnan, I.K.; Yakhmi, J.V.

2000-01-01

We show that the compound La 1.2 Ca 1.8 Mn 2 O 7 does not form with layered Sr 3 Ti 2 O 7 -type structure as reported by Kamenev et al. [Phys. Rev. B 56, R12 688 (1997)]. Detailed analysis of the powder x-ray diffraction pattern of this compound (synthesized by using the solid-state method) by Rietveld method shows that it forms a multiphase mixture comprising hole-doped perovskite manganates (La 1-x Ca x MnO 3 ) as the majority phases and CaO as the minority phase

Studies of diluted antiferromagnets MnxMg1-xTiO3 with x=0.55 and 0.70 by muon spin relaxation method

International Nuclear Information System (INIS)

Fukaya, A.; Ito, A.; Torikai, E.; Nishiyama, K.; Nagamine, K.

1997-01-01

Longitudinal fields μSR measurements have been performed in order to probe the spin dynamics in the diluted antiferromagnets Mn x Mg 1-x TiO 3 with x=0.70 and 0.55. In the x=0.70 sample which forms the antiferromagnetic long-range order, the static and fluctuating fields coexist at the muon stopping site below T N . On the other hand, in the x=0.55 sample which shows the spin-glass behavior, the local fields fluctuate rather fast even below T SG . We infer that this drastic change occurs when Mn x Mg 1-x TiO 3 transforms from an antiferromagnetic system to a spin-glass system by dilution

The Mn site in Mn-doped GaAs nanowires: an EXAFS study

International Nuclear Information System (INIS)

D’Acapito, F; Rovezzi, M; Boscherini, F; Jabeen, F; Bais, G; Piccin, M; Rubini, S; Martelli, F

2012-01-01

We present an EXAFS study of the Mn atomic environment in Mn-doped GaAs nanowires. Mn doping has been obtained either via the diffusion of the Mn used as seed for the nanowire growth or by providing Mn during the growth of Au-induced wires. As a general finding, we observe that Mn forms chemical bonds with As but is not incorporated in a substitutional site. In Mn-induced GaAs wires, Mn is mostly found bonded to As in a rather disordered environment and with a stretched bond length, reminiscent of that exhibited by MnAs phases. In Au-seeded nanowires, along with stretched MnAs coordination, we have found the presence of Mn in a MnAu intermetallic compound. (paper)

Antiferromagnetic MnN layer on the MnGa(001) surface

Energy Technology Data Exchange (ETDEWEB)

Guerrero-Sánchez, J., E-mail: guerrero@cnyn.unam.mx; Takeuchi, Noboru

2016-12-30

Highlights: • A ferromagnetic Gallium terminated surface is stable before N incorporation. • After N incorporation, an antiferromagnetic MnN layer becomes stable in a wide range of chemical potential. • Spin density distribution shows an antiferromagnetic/ferromagnetic (MnN/MnGa) arrangement at the surface. - Abstract: Spin polarized first principles total energy calculations have been applied to study the stability and magnetic properties of the MnGa(001) surface and the formation of a topmost MnN layer with the deposit of nitrogen. Before nitrogen adsorption, surface formation energies show a stable gallium terminated ferromagnetic surface. After incorporation of nitrogen atoms, the antiferromagnetic manganese terminated surface becomes stable due to the formation of a MnN layer (Mn-N bonding at the surface). Spin density distribution shows a ferromagnetic/antiferromagnetic arrangement in the first surface layers. This thermodynamically stable structure may be exploited to growth MnGa/MnN magnetic heterostructures as well as to look for exchange biased systems.

Electric-field control of electronic transport properties and enhanced magnetoresistance in La0.7Sr0.3MnO3/0.5BaZr0.2Ti0.8O3-0.5Ba0.7Ca0.3TiO3 lead-free multiferroic structures

Science.gov (United States)

Yan, Jian-Min; Gao, Guan-Yin; Liu, Yu-Kuai; Wang, Fei-Fei; Zheng, Ren-Kui

2017-10-01

We report the fabrication of lead-free multiferroic structures by depositing ferromagnetic La0.7Sr0.3MnO3 (LSMO) polycrystalline films on polished 0.5BaZr0.2Ti0.8O3-0.5Ba0.7Ca0.3TiO3 (BZT-BCT) piezoelectric ceramic substrates. By applying electric fields to the BZT-BCT along the thickness direction, the resistivity of LSMO films can be effectively manipulated via the piezoelectric strain of the BZT-BCT. Moreover, the LSMO polycrystalline films exhibit almost temperature independent and significantly enhanced magnetoresistance (MR) below TC. At T = 2 K and H = 8 T, the MR of polycrystalline films is approximately two orders of magnitude higher than that of LSMO epitaxial films grown on (LaAlO3)0.3(SrAl1/2Ta1/2O3)0.7 single-crystal substrates. The enhanced MR mainly results from the spin-polarized tunneling of charge carriers across grain boundaries. The LSMO/BZT-BCT structures with electric-field controllable modulation of resistivity and enhanced MR effect may have potential applications in low-energy consumption and environmentally friendly electronic devices.

Domain wall conductivity in semiconducting hexagonal ferroelectric TbMnO3 thin films

International Nuclear Information System (INIS)

Kim, D J; Gruverman, A; Connell, J G; Seo, S S A

2016-01-01

Although enhanced conductivity of ferroelectric domain boundaries has been found in BiFeO 3 and Pb(Zr,Ti)O 3 films as well as hexagonal rare-earth manganite single crystals, the mechanism of the domain wall conductivity is still under debate. Using conductive atomic force microscopy, we observe enhanced conductance at the electrically-neutral domain walls in semiconducting hexagonal ferroelectric TbMnO 3 thin films where the structure and polarization direction are strongly constrained along the c-axis. This result indicates that domain wall conductivity in ferroelectric rare-earth manganites is not limited to charged domain walls. We show that the observed conductivity in the TbMnO 3 films is governed by a single conduction mechanism, namely, the back-to-back Schottky diodes tuned by the segregation of defects. (paper)

Fourier transform spectroscopy of MnH and MnD

Science.gov (United States)

Balfour, W. J.; Launila, O.; Klynning, L.

Two infrared band systems, centred near 846 nm and 1060 nm in both MnH and MnD have been rotationally analysed and shown to have a common lower state. The electronic transitions lie within the quintet manifold and are here designated c 5Σ-a 5Σ and b 5Πi-a 5Σ for the 846 and 1060 nm systems, respectively. In the 846 nm system in MnH all 10 main branches have been found in the 0-0 and 1-1 bands, while in MnD the data are complete only for 0-0. Satellite branches have been identified in the 1060 nm system and all spin and Λ-type doublings have been established. The number of assigned 0-0 branches in the 1060 nm system is 35 for MnH and 37 for MnD. Molecular constants have been determined for all three states involved. Λ-doubling diagrams are presented for b 5Πi state with v = 1, 2 levels in MnH and with the v = 2 level in MnD. Local perturbations in c5Σ (v = 1) in MnH are suspected to originate from the v = 3 level of b 5Πi.

Solid-state reactions during mechanical alloying of ternary Fe-Al-X (X=Ni, Mn, Cu, Ti, Cr, B, Si) systems: A review

Science.gov (United States)

Hadef, Fatma

2016-12-01

The last decade has witnessed an intensive research in the field of nanocrystalline materials due to their enhanced properties. A lot of processing techniques were developed in order to synthesis these novel materials, among them mechanical alloying or high-energy ball milling. In fact, mechanical alloying is one of the most common operations in the processing of solids. It can be used to quickly and easily synthesize a variety of technologically useful materials which are very difficult to manufacture by other techniques. One advantage of MA over many other techniques is that is a solid state technique and consequently problems associated with melting and solidification are bypassed. Special attention is being paid to the synthesis of alloys through reactions mainly occurring in solid state in many metallic ternary Fe-Al-X systems, in order to improve mainly Fe-Al structural and mechanical properties. The results show that nanocrystallization is the common result occurring in all systems during MA process. The aim of this work is to illustrate the uniqueness of MA process to induce phase transformation in metallic Fe-Al-X (X=Ni, Mn, Cu, Ti, Cr, B, Si) systems.

Study of radiation damage in BaTiO3, using Molecular-dynamics simulations

International Nuclear Information System (INIS)

Gonzalez, E.; Abreu, Y.; Cruz, C. M.; Pinnera, I.; Leyva, A.

2015-01-01

Molecular-dynamics (MD) simulations were used to calculate atomic displacement probability curves along main crystallographic directions in BaTiO 3 perovskite. A primary knock-on atom (PKA) with a energy range between 10 to 300 eV in principal crystallographic directions at 300 K was introduced. For each sublattice, the simulation was repeated from different initial conditions to estimate the variation in the defect formation process. The formation of Frenkel pairs vary considerably with crystallographic direction and sublattice. Major quantity oxygen defects were found for all the simulated crystallographic directions. Threshold displacement energies are calculated for each atomic specie in the BaTiO 3 material. Also simulations with SRIM code, modeling + Mn implantation in a BaTiO 3 target, at 250 keV were made. (Author)

Oxygen incorporation effects in annealed epitaxial La(1-x)SrxMnO3 thin films

International Nuclear Information System (INIS)

Petrisor, T.; Gabor, M. S.; Tiusan, C.; Boulle, A.; Bellouard, C.; Pana, O.; Petrisor, T.

2011-01-01

This paper presents our results regarding oxygen incorporation effects in epitaxial La (1-x) Sr x MnO 3 thin films, deposited on SrTiO 3 (001) single crystal substrates, by annealing in different gas mixtures of argon and oxygen. A particular emphasis is placed on the correlation of structural properties with the magnetic properties of the films, Curie temperature, and coercive field. In this sense, we demonstrate that the evolution of the diffuse part of the ω-scans performed on the films are due to oxygen excess in the film lattice, which creates cationic vacancies within the films. Also, we show that two regimes of oxygen incorporation in the films exist, one in which the films evolve toward a single phase and oxygen stoichiometry is recovered, and a second one dominated by oxygen over-doping effects. In order to support our study, XPS measurements were performed, from which we have evaluated the Mn 3+ /Mn 4+ ionic ratio.

Tuning the magnetic properties of GaAs:Mn/MnAs hybrids via the MnAs cluster shape

International Nuclear Information System (INIS)

Nidda, H-A Krug von; Kurz, T; Loidl, A; Hartmann, Th; Klar, P J; Heimbrodt, W; Lampalzer, M; Volz, K; Stolz, W

2006-01-01

We report a systematic study of ferromagnetic resonance in granular GaAs:Mn/MnAs hybrids grown on GaAs(001) substrates by metal-organic vapour-phase epitaxy. The ferromagnetic resonance of the MnAs clusters can be resolved at all temperatures below T c . An additional broad absorption is observed below 60 K and is ascribed to localized charge carriers of the GaAs:Mn matrix. The anisotropy of the MnAs ferromagnetic resonance field originates from the magneto-crystalline field and demagnetization effects of the ferromagnetic MnAs clusters embedded in the GaAs:Mn matrix. Its temperature dependence basically scales with magnetization. Comparison of the observed angular dependence of the resonance field with model calculations yields the preferential orientation and shape of the clusters formed in hybrid layers of different thickness (150-1000 nm) grown otherwise at the same growth conditions. The hexagonal axes of the MnAs clusters are oriented along the four cubic GaAs space diagonals. Thin layers contain lens-shaped MnAs clusters close to the surface, whereas thick layers also contain spherical clusters in the bulk of the layer. The magnetic properties of the hexagonal MnAs clusters can be tuned by a controlled variation of the cluster shape

A combined experimental and computational study of water-gas shift reaction over rod-shaped Ce_0.75 M_0.25O₂ (M=Ti, Zr, and Mn) supported Cu catalysts

Energy Technology Data Exchange (ETDEWEB)

Ren, Zhibo; Peng, Fei; Chen, Biaohua; Mei, Donghai; Li, Jianwei

2017-11-02

Water-gas shift (WGS) reaction over a series of ceria-based mixed oxides supported Cu catalysts was investigated using a combined experimental and theoretical method. The mixed rod-shaped Ce_0.75M_0.25O₂ (M = Ti⁴⁺, Zr⁴⁺, Mn⁴⁺) solid solutions, which majorly expose the (110) and (100) facets, are synthesized by hydrothermal method and used to prepare supported Cu catalysts. We found that the Cu/Ce0.75Ti_0.25O₂ (Cu-CT) exhibits the highest CO conversion in the temperature range of 150-250 °C among all supported Cu catalysts. This is mainly attributed to (i) good dispersion of Cu; (ii) largest amount of moderate copper oxide; and (iii) strongest Cu-support interaction of Cu-CT. And compared to other mixed metals, periodic density functional theory calculations performed, this work further suggest that the introduction of Ti into CeO₂ not only promotes oxygen vacancy formation and CO adsorption, but also facilitates the carboxyl (COOH) formation at the interface of the Cu cluster and the support, which leads to the enhanced catalytic activity of the Cu-CT toward WGS reaction.

Large anisotropy in colossal magnetoresistance of charge orbital ordered epitaxial Sm0.5Ca0.5MnO3 films

DEFF Research Database (Denmark)

Chen, Yunzhong; Sun, J.R.; Zhao, J.L.

2009-01-01

We investigated the structure and magnetotransport properties of Sm0.5Ca0.5MnO3 (SCMO) films epitaxially grown on (011)-oriented SrTiO3 substrates, which exhibited clear charge/orbital ordering transition. A significant anisotropy of ~1000 in the colossal magnetoresistance (CMR) effect was observ...

Effect of Manganese Addition on the Structure, Magnetic Properties and Microwave Absorption of La0.8Ba0.2MnxFe½(1-x)Ti½(1-x)O3

Science.gov (United States)

Adi, W. A.; Indro, M. N.; Kusumastuti, A. A.

2017-03-01

We have carried out modification of La0.8Ba0.2MnxFe½(1-x)Ti½(1-x)O3 (x = 0.1 - 0.8) magnetic materials by wet milling method. Raw materials of La2O3, BaCO3, Fe2O3, TiO2 and MnCO3 were mixed according to stoichiometry calculation for each composition. The mixture was milled for 5 hours and then sintered at 1000 °C for 5 hours. The refinement results by X-ray diffraction pattern shows that the increasing Mn composition enhances the mass fraction of La0.8Ba0.2MnxFe½(1-x)Ti½(1-x)O3 phase which has the same structure as LaMnO3. For x = 0.8 a single phase of LaMnO3 was formed. The single phase has a crystal monoclinic crystal structure with space group of I 1 2 / a 1, with lattice parameters given by a = 5.519(5) Å, b = 5.5537(5) Å and c = 7.8176(9) Å, α = γ = 90o and β = 90.345(6)o, V = 239.64(3) Å3, ρ = 6.463 gr.cm-3, wRp = 5.96, and χ2 (chi-squared) = 1.17. The hysteresis curve shows that the sample with composition x = 0.8 produces ferromagnetic behaviour at room temperature. The ferromagnetic properties arise due to the mixed valence of Mn3+ and Mn4+ ions through a double exchange mechanism. The results of the microwave absorption indicated that there was a broadening of absorption peak frequency at 9.9 GHz. The reflection loss (RL) increases with the increasing of LaMnO3 phase. For x = 0.8 we have the best of RL where the microwave absorption was calculated reaching 95% at the highest peak frequency with a thickness of 1.5 mm. Thus we have been successful in creating a single phase of La0.8Ba0.2MnxFe½(1-x)Ti½(1-x)O3 with application as a microwave absorber.

Control of the magnetic properties of LaMnO3 epitaxial thin films grown by Pulsed Laser Deposition

Science.gov (United States)

Martinez, Benjamin; Roqueta, Jaume; Pomar, Alberto; Balcells, Lluis; Frontera, Carlos; Konstantinovic, Zorica; Sandiumenge, Felip; Santiso, Jose; Advanced materials characterization Team; Thin films growth Team

2015-03-01

LaMnO3 (LMO), the parent compound of colossal magnetoresistance based manganites has gained renewed attention as a building block in heterostructures with unexpected properties. In its bulk phase, stoichiometric LMO is an A-type antiferromagnetic (AFM) insulator (TN = 140K) with orthorhombic structure that easily accommodate an oxygen excess by generating cationic (La or Mn) vacancies. As a result, a fraction of Mn 3+ changes to Mn 4+ leading to a double-exchange mediated ferromagnetic (FM) behavior. In thin films the AFM phase has been elusive up to now and thin films with FM ordering are usually reported. In this work, we have systematically studied the growth process of LaMnO3 thin films by pulsed laser deposition on SrTiO3 (001) substrates under different oxygen partial pressures (PO2) . A close correlation between the structure (explored by XRD) and the magnetic properties (SQUID measurements) of the films with PO2 has been identified. At high PO2 FM behavior is observed. In contrast, at very low PO2, the results obtained for unit cell volume (close to stoichiometric bulk values) and magnetic moment (0.2 μB/Mn) strongly indicate antiferromagnetic ordering. We acknowledge financial support from the Spanish MINECO (MAT2012-33207).

Identification of the interstitial Mn site in ferromagnetic (Ga,Mn)As

CERN Document Server

AUTHOR|(CDS)2093111; Wahl, Ulrich; Augustyns, Valerie; Silva, Daniel; Granadeiro Costa, Angelo Rafael; Houben, K; Edmonds, Kevin W; Gallagher, BL; Campion, RP; Van Bael, MJ; Castro Ribeiro Da Silva, Manuel; Martins Correia, Joao; Esteves De Araujo, Araujo Joao Pedro; Temst, Kristiaan; Vantomme, André; Da Costa Pereira, Lino Miguel

2015-01-01

We determined the lattice location of Mn in ferromagnetic (Ga,Mn)As using the electron emission channeling technique. We show that interstitial Mn occupies the tetrahedral site with As nearest neighbors (TAs) both before and after thermal annealing at 200 °C, whereas the occupancy of the tetrahedral site with Ga nearest neighbors (TGa) is negligible. TAs is therefore the energetically favorable site for interstitial Mn in isolated form as well as when forming complexes with substitutional Mn. These results shed new light on the long standing controversy regarding TAs versus TGa occupancy of interstitial Mn in (Ga,Mn)As.

Hydrogen storage performance of Ti-V-based BCC phase alloys with various Fe content

International Nuclear Information System (INIS)

Yu, X.B.; Feng, S.L.; Wu, Z.; Xia, B.J.; Xu, N.X.

2005-01-01

The effect of Fe content on hydrogen storage characteristics of Ti-10Cr-18Mn-(32-x)V-xFe (x = 0, 2, 3, 4, 5) alloys has been investigated at 353 K. The X-ray diffraction (XRD) patterns and scanning electron microscopy (SEM) images of the alloys present BCC and C14 two-phase structures for all of the Fe-containing alloys. With the increasing Fe content, the lattice parameters of the BCC phase decrease, which results in an increase of the hydrogen desorption plateau pressure of the alloys. Among the studied alloys, Ti-10Cr-18Mn-27V-5Fe alloy exhibits the smallest PCT plateau slope and a more suitable plateau pressure (0.1 MPa equ <1 MPa). The maximum and effective capacities of the alloy are 3.32 wt.% and 2.26 wt.%, respectively, which are higher than other reported Fe-containing BCC phase alloys. In addition, the V/Fe ratio in this alloy is close to that of (VFe) alloy, whose cost is much lower than that of pure V

First-principles calculations of the electronic, vibrational, and elastic properties of the magnetic laminate Mn2GaC

International Nuclear Information System (INIS)

Thore, A.; Dahlqvist, M.; Alling, B.; Rosén, J.

2014-01-01

In this paper, we report the by first-principles predicted properties of the recently discovered magnetic MAX phase Mn 2 GaC. The electronic band structure and vibrational dispersion relation, as well as the electronic and vibrational density of states, have been calculated. The band structure close to the Fermi level indicates anisotropy with respect to electrical conductivity, while the distribution of the electronic and vibrational states for both Mn and Ga depend on the chosen relative orientation of the Mn spins across the Ga sheets in the Mn–Ga–Mn trilayers. In addition, the elastic properties have been calculated, and from the five elastic constants, the Voigt bulk modulus is determined to be 157 GPa, the Voigt shear modulus 93 GPa, and the Young's modulus 233 GPa. Furthermore, Mn 2 GaC is found relatively elastically isotropic, with a compression anisotropy factor of 0.97, and shear anisotropy factors of 0.9 and 1, respectively. The Poisson's ratio is 0.25. Evaluated elastic properties are compared to theoretical and experimental results for M 2 AC phases where M = Ti, V, Cr, Zr, Nb, Ta, and A = Al, S, Ge, In, Sn.

Onset of phase separation in the double perovskite oxide mn>2mn>MnNiO>6mn>

Energy Technology Data Exchange (ETDEWEB)

Spurgeon, Steven R.; Sushko, Peter V.; Devaraj, Arun; Du, Yingge; Droubay, Timothy; Chambers, Scott A.

2018-04-01

Identification of kinetic and thermodynamic factors that control crystal nucleation and growth represents a central challenge in materials synthesis. Here we report that apparently defect-free growth of La2MnNiO6 (LMNO) thin films supported on SrTiO3 (STO) proceeds up to 1–5 nm, after which it is disrupted by precipitation of NiO phases. Local geometric phase analysis and ensemble-averaged x-ray reciprocal space mapping show no change in the film strain away from the interface, indicating that mechanisms other than strain relaxation induce the formation of the NiO phases. Ab initio simulations suggest that the electrostatic potential build-up associated with the polarity mismatch at the film-substrate interface promotes the formation of oxygen vacancies with increasing thickness. In turn, oxygen deficiency promotes the formation of Ni-rich regions, which points to the built-in potential as an additional factor that contributes to the NiO precipitation mechanisms. These results suggest that the precipitate-free region could be extended further by either incorporating dopants that suppress the built-in potential or by increasing the oxygen fugacity in order to suppress the formation of oxygen vacancies.

Relationships between environment and characteristics of marine Fe-Mn deposits in the Romanche trench

International Nuclear Information System (INIS)

Bonte, Philippe.

1981-11-01

The geological characteristics and Fe-Mn deposits from the North wall of the Romanche trench (Atlantic ocean) were studied in order to investigate possible relationships of these deposits with hydrothermalism. The results indicate diffuse hydrothermal activity in all of the rock samples which may explain the notable mineralogical associations observed, such as talc-dolomite-hematite-serpentine. All rock outcrops were covered with Fe-Mn deposits, but no such deposits were noted on sedimentary platforms. The variations in average chemical composition are very low among the different deposits. Hence, the phenomenon which produces these deposits is not localized. From this study, we conclude that marine Fe-Mn deposits result from the continuous supply of terrigenous iron and discontinuous supply of manganese, probably hydrothermal in origin. Detrital particles and numerous chemical elements are scavenged during the accretion process itself, whereas some trace elements, among the least soluble (Co, Ti, Th, Ce), are adsorbed on these deposits, independently of the accretion. This explains the inverse variation of the content of these elements versus deposit thickness [fr

Effects of doping on ferroelectric properties and leakage current behavior of KNN-LT-LS thin films on SrTiO3 substrate

Science.gov (United States)

Abazari, M.; Safari, A.

2009-05-01

We report the effects of Ba, Ti, and Mn dopants on ferroelectric polarization and leakage current of (K0.44Na0.52Li0.04)(Nb0.84Ta0.1Sb0.06)O3 (KNN-LT-LS) thin films deposited by pulsed laser deposition. It is shown that donor dopants such as Ba2+, which increased the resistivity in bulk KNN-LT-LS, had an opposite effect in the thin film. Ti4+ as an acceptor B-site dopant reduces the leakage current by an order of magnitude, while the polarization values showed a slight degradation. Mn4+, however, was found to effectively suppress the leakage current by over two orders of magnitude while enhancing the polarization, with 15 and 23 μC/cm2 remanent and saturated polarization, whose values are ˜70% and 82% of the reported values for bulk composition. This phenomenon has been associated with the dual effect of Mn4+ in KNN-LT-LS thin film, by substituting both A- and B-site cations. A detailed description on how each dopant affects the concentrations of vacancies in the lattice is presented. Mn-doped KNN-LT-LS thin films are shown to be a promising candidate for lead-free thin films and applications.

Multireversible redox processes in pentanuclear bis(triple-helical) manganese complexes featuring an oxo-centered triangular {Mn(II)2Mn(III)(μ3-O)}5+ or {Mn(II)Mn(III)2(μ3-O)}6+ core wrapped by two {Mn(II)2(bpp)3}-.