Solvothermal preparation of micro/nanostructured TiO_2 with enhanced lithium storage capability

International Nuclear Information System (INIS)

Li, Jie; Wang, Chao; Zheng, Ping; Zhang, Lei; Chen, Gongxuan; Tang, Chengchun; Wu, Tian

2017-01-01

Facile and controllable preparation of TiO_2 is of prime importance to elaborately tailor and then fully exploit its intriguing functionalities in energy storage, catalysis and environmental remediation. Herein, a solvothermal method combined with post annealing is conducted, in which the hydrolysis of tetrabutyl titanate is controlled by the in-situ generated water during solvothermal treatment. By controlling synthetic conditions (i.e. reactant ratio, solvothermal temperature and reaction time), we manage to tailor the morphologies of TiO_2. Specially, three typical structures (nanoparticle, nanoneedle and nanorod) are studied to reveal the growth mechanism and the effects of the synthesis conditions. Nanoneedle-structured TiO_2 shows higher specific capacity and enhanced cycle stability as anode material for lithium ion batteries. - Highlights: • Controllable preparation of nano-TiO_2 is achieved by a solvothermal method. • TiO_2 morphology is tailored by tuning reactant ratio, temperature and duration. • Needle structured TiO_2 shows enhanced lithium storage capability.

[Experimental study and correction of the absorption and enhancement effect between Ti, V and Fe].

Science.gov (United States)

Tuo, Xian-Guo; Mu, Ke-Liang; Li, Zhe; Wang, Hong-Hui; Luo, Hui; Yang, Jian-Bo

2009-11-01

The absorption and enhancement effects in X-ray fluorescence analysis for Ti, V and Fe elements were studied in the present paper. Three bogus duality systems of Ti-V/Ti-Fe/V-Fe samples were confected and measured by X-ray fluorescence analysis technique using HPGe semiconductor detector, and the relation curve between unitary coefficient (R(K)) of element count rate and element content (W(K)) were obtained after the experiment. Having analyzed the degree of absorption and enhancement effect between every two elements, the authors get the result, and that is the absorption and enhancement effect between Ti and V is relatively distinctness, while it's not so distinctness in Ti-Fe and V-Fe. After that, a mathematics correction method of exponential fitting was used to fit the R(K)-W(K) curve and get a function equation of X-ray fluorescence count rate and content. Three groups of Ti-V duality samples were used to test the fitting method and the relative errors of Ti and V were less than 0.2% as compared to the actual results.

Construction of AgBr nano-cakes decorated Ti3+ self-doped TiO2 nanorods/nanosheets photoelectrode and its enhanced visible light driven photocatalytic and photoelectrochemical properties

Science.gov (United States)

Deng, Xiaoyong; Zhang, Huixuan; Guo, Ruonan; Cheng, Xiuwen; Cheng, Qingfeng

2018-05-01

In the study, AgBr nano-cakes decorated Ti3+ self-doped TiO2 nanorods/nanosheets (AgBr-Ti3+/TiO2 NRs/NSs) photoelectrode with enhanced visible light driven photocatalytic (PC) and photoelectrochemical (PECH) performance has been successfully fabricated by hydrothermal reaction, followed by sodium borohydride reduction and then successive ionic layer adsorption and reaction (SILAR) treatment. Afterwards, series of characterizations were conducted to study the physicochemical properties of AgBr-Ti3+/TiO2 NRs/NSs photoelectrode. Results indicated that AgBr nano-cakes with sizes varying from 110 to 180 nm were uniformly decorated on the surface of Ti3+/TiO2 NRs/NSs to form AgBr-Ti3+/TiO2 NRs/NSs photoelectrode. Moreover, PC activity of AgBr-Ti3+/TiO2 NRs/NSs photoelectrode was measured by degradation of methylene blue (MB). It was found that AgBr-Ti3+/TiO2 NRs/NSs photoelectrode exhibited higher PC activity (98.7%) than that of other samples within 150 min visible light illumination, owing to the enhancement of visible light harvesting and effective separation of photoproduced charges. Thus, AgBr nano-cakes and Ti3+ exerted a huge influence on the PC and PECH properties of AgBr-Ti3+/TiO2 NRs/NSs photoelectrode. Furthermore, the possible enhanced visible light driven PC mechanism of AgBr-Ti3+/TiO2 NRs/NSs was proposed and confirmed.

Nitride coating enhances endothelialization on biomedical NiTi shape memory alloy

Energy Technology Data Exchange (ETDEWEB)

Ion, Raluca [University of Bucharest, Department of Biochemistry and Molecular Biology, 91-95 Spl. Independentei, 050095 Bucharest (Romania); Luculescu, Catalin [National Institute for Laser, Plasma and Radiation Physics, 409 Atomistilor, P.O. Box MG-36, 077125 Magurele-Bucharest (Romania); Cimpean, Anisoara, E-mail: anisoara.cimpean@bio.unibuc.ro [University of Bucharest, Department of Biochemistry and Molecular Biology, 91-95 Spl. Independentei, 050095 Bucharest (Romania); Marx, Philippe [AMF Company, Route de Quincy, 18120 Lury-sur-Arnon (France); Gordin, Doina-Margareta; Gloriant, Thierry [INSA Rennes, UMR CNRS 6226 ISCR, 20 Avenue des Buttes de Coësmes, 35708 Rennes Cedex 7 (France)

2016-05-01

Surface nitriding was demonstrated to be an effective process for improving the biocompatibility of implantable devices. In this study, we investigated the benefits of nitriding the NiTi shape memory alloy for vascular stent applications. Results from cell experiments indicated that, compared to untreated NiTi, a superficial gas nitriding treatment enhanced the adhesion of human umbilical vein endothelial cells (HUVECs), cell spreading and proliferation. This investigation provides data to demonstrate the possibility of improving the rate of endothelialization on NiTi by means of nitride coating. - Highlights: • Gas nitriding process of NiTi is competent to promote cell spreading. • Surface nitriding of NiTi is able to stimulate focal adhesion formation and cell proliferation. • Similar expression pattern of vWf and eNOS was exhibited by bare and nitrided NiTi. • Gas nitriding treatment of NiTi shows promise for better in vivo endothelialization.

Non-noble metal Cu-loaded TiO2 for enhanced photocatalytic H2 production.

Science.gov (United States)

Foo, Wei Jian; Zhang, Chun; Ho, Ghim Wei

2013-01-21

Here we have demonstrated the preparation of high-quality, monodispersed and tunable phases of Cu nanoparticles. Structural and chemical composition studies depict the evolution of Cu-Cu(2)O-CuO nanoparticles at various process stages. The loading of Cu and Cu oxide nanoparticles on TiO(2) catalyst has enhanced the photocatalytic H(2) production. Comparatively, H(2) treatment produces well-dispersed Cu nanoparticles with thin oxide shells that show the highest H(2) production amongst the samples. The relatively higher photocatalytic performance is deemed to result from reduced structural defects, higher surface area and dispersivity as well as favorable charge transfer, which inhibits recombination. The Cu nanoparticles are shown to be a promising alternative to noble metal-loaded TiO(2) catalyst systems due to their low cost and high performance in photocatalytic applications.

Core-shell SrTiO3/graphene structure by chemical vapor deposition for enhanced photocatalytic performance

Science.gov (United States)

He, Chenye; Bu, Xiuming; Yang, Siwei; He, Peng; Ding, Guqiao; Xie, Xiaoming

2018-04-01

Direct growth of high quality graphene on the surface of SrTiO3 (STO) was realized through chemical vapor deposition (CVD), to construct few-layer 'graphene shell' on every STO nanoparticle. The STO/graphene composite shows significantly enhanced UV light photocatalytic activity compared with the STO/rGO reference. Mechanism analysis confirms the role of special core-shell structure and chemical bond (Tisbnd C) for rapid interfacial electron transfer and effective electron-hole separation.

Surface Plasmon Enhanced Photocatalysis of Au/Pt-decorated TiO2 Nanopillar Arrays

Science.gov (United States)

Shuang, Shuang; Lv, Ruitao; Xie, Zheng; Zhang, Zhengjun

2016-05-01

The low quantum yields and lack of visible light utilization hinder the practical application of TiO2 in high-performance photocatalysis. Herein, we present a design of TiO2 nanopillar arrays (NPAs) decorated with both Au and Pt nanoparticles (NPs) directly synthesized through successive ion layer adsorption and reaction (SILAR) at room temperature. Au/Pt NPs with sizes of ~4 nm are well-dispersed on the TiO2 NPAs as evidenced by electron microscopic analyses. The present design of Au/Pt co-decoration on the TiO2 NPAs shows much higher visible and ultraviolet (UV) light absorption response, which leads to remarkably enhanced photocatalytic activities on both the dye degradation and photoelectrochemical (PEC) performance. Its photocatalytic reaction efficiency is 21 and 13 times higher than that of pure TiO2 sample under UV-vis and visible light, respectively. This great enhancement can be attributed to the synergy of electron-sink function of Pt and surface plasmon resonance (SPR) of Au NPs, which significantly improves charge separation of photoexcited TiO2. Our studies demonstrate that through rational design of composite nanostructures one can harvest visible light through the SPR effect to enhance the photocatalytic activities initiated by UV-light, and thus realize more effectively utilization of the whole solar spectrum for energy conversion.

Hardness enhancement and oxidation resistance of nanocrystalline TiN/Mo xC multilayer films

International Nuclear Information System (INIS)

Liu, Q.; Wang, X.P.; Liang, F.J.; Wang, J.X.; Fang, Q.F.

2006-01-01

In this paper the influence of the layer's microstructure on the hardness enhancement in multilayer nanocrystalline films and the oxidation resistance are studied. The TiN/Mo x C multilayer films at different modulation period, and Mo x C and TiN monolayer films were deposited on the (0 0 1) silicon wafers and molybdenum sheets by rf and dc magnetron sputtering. The monolayer TiN films with a thickness of about 2 μm are of pure face-center cubic TiN phase, while the monolayer Mo x C films consist of two phases, one of which is body-center cubic Mo and the other is hexagonal Mo 2 C as determined by XRD. The coarse columnar grains of about 200 nm in the monolayer TiN films become much smaller or disappear in the multilayer films. The hardness enhancement of the multilayer films takes place at the modulation period of 320 nm, which can reach to 26 GPa and is much higher than the values of Mo x C and TiN monolayer films. This enhancement in hardness can be explained as the decrease in the size and/or disappearance of columnar grains in the TiN layer. The Young's modulus in the temperature range from 100 to 400 deg. C increases with decreasing modulation period. It is found that about 100 nm thick TiN films can increase largely the oxidation resistance of Mo x C films

Adhesion enhancement of diamond-like carbon thin films on Ti alloys by incorporation of nanodiamond particles

International Nuclear Information System (INIS)

Zhang, C.Z.; Tang, Y.; Li, Y.S.; Yang, Q.

2013-01-01

Coating adherent diamond-like carbon (DLC) thin films directly on Ti alloys is technologically difficult. This research incorporates nanodiamond particles to form a diamond/DLC composite interlayer to enhance the adhesion of DLC thin films on Ti6Al4V substrates. Initially, nanodiamond particles were deposited on Ti6Al4V substrates by microwave plasma enhanced chemical vapor deposition from a methane–hydrogen gas mixture. A DLC thin film was then deposited, on top of the nanodiamond particles, by direct ion beam deposition. Scanning electron microscopy, Atomic force microscopy, X-ray Diffraction and Raman spectroscopy were used to characterize the microstructure and chemical bonding of the deposited particles and films, and Rockwell indentation testing was used to evaluate the adhesion of the deposited films. The results indicate that the pre-deposited nanodiamond particles significantly enhance the interfacial adhesion between the DLC thin film and the Ti6Al4V substrate, possibly by enhanced interfacial bonding, mechanical interlocking, and stress relief. - Highlights: ► Nanodiamond particles were deposited on Ti6Al4V before DLC deposition. ► Diamond/DLC composite film was formed by incorporation of nanodiamond particles. ► Greatly enhanced adhesion of diamond/DLC composite film on Ti6Al4V was achieved. ► Enhanced adhesion is by increased interfacial bonding and mechanical interlocking

Adhesion enhancement of diamond-like carbon thin films on Ti alloys by incorporation of nanodiamond particles

Energy Technology Data Exchange (ETDEWEB)

Zhang, C.Z.; Tang, Y. [Department of Mechanical Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK, Canada S7N 5A9 (Canada); Li, Y.S. [Plasma Physics Laboratory, University of Saskatchewan, 116 Science Place, Saskatoon, SK, Canada S7N 5E2 (Canada); Yang, Q., E-mail: qiaoqin.yang@usask.ca [Department of Mechanical Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK, Canada S7N 5A9 (Canada)

2013-01-01

Coating adherent diamond-like carbon (DLC) thin films directly on Ti alloys is technologically difficult. This research incorporates nanodiamond particles to form a diamond/DLC composite interlayer to enhance the adhesion of DLC thin films on Ti6Al4V substrates. Initially, nanodiamond particles were deposited on Ti6Al4V substrates by microwave plasma enhanced chemical vapor deposition from a methane–hydrogen gas mixture. A DLC thin film was then deposited, on top of the nanodiamond particles, by direct ion beam deposition. Scanning electron microscopy, Atomic force microscopy, X-ray Diffraction and Raman spectroscopy were used to characterize the microstructure and chemical bonding of the deposited particles and films, and Rockwell indentation testing was used to evaluate the adhesion of the deposited films. The results indicate that the pre-deposited nanodiamond particles significantly enhance the interfacial adhesion between the DLC thin film and the Ti6Al4V substrate, possibly by enhanced interfacial bonding, mechanical interlocking, and stress relief. - Highlights: ► Nanodiamond particles were deposited on Ti6Al4V before DLC deposition. ► Diamond/DLC composite film was formed by incorporation of nanodiamond particles. ► Greatly enhanced adhesion of diamond/DLC composite film on Ti6Al4V was achieved. ► Enhanced adhesion is by increased interfacial bonding and mechanical interlocking.

TiO2 nanoparticles immobilized on carbon nanotubes for enhanced visible-light photo-induced activity

Directory of Open Access Journals (Sweden)

Ali Akbar Ashkarran

2015-04-01

Full Text Available CNT–TiO2 nanocomposites were prepared through (i simple mixing of as prepared CNTs and TiO2 nanoparticles (NPs, (ii simple mixing of as prepared CNTs and TiO2 NPs followed by heat treatment and (iii simple mixing of as prepared CNTs and TiO2 NPs followed by UV illumination. The synthesis of CNTs and TiO2 NPs were performed individually by arc discharge in water and sol–gel methods, respectively and characterized by X-ray diffraction (XRD, ultra violet and visible spectroscopy (UV–vis, Fourier transform infrared spectroscopy (FT-IR, scanning electron microscopy (SEM and transmission electron microscopy (TEM. The visible-light photocatalytic performance of CNT–TiO2 nanocomposites was successfully demonstrated for the degradation of Rhodamine B (Rh. B as a model dye at room temperature. It is found that CNT–TiO2 nanocomposites extended the light absorption spectrum toward the visible region and considerably improved the photocatalytic efficiency under visible-light irradiation. The visible-light photocatalytic activities of CNT–TiO2 nanocomposites in which CNTs are produced by arc discharge in deionized (DI water at 40, 60 and 80 A arc currents and combined through three different protocols are also investigated. It was found that samples prepared at 80 A arc current and 5 s arc duration followed by UV illumination revealed best photocatalytic activity compared with the same samples prepared under simple mixing and simple mixing followed by heat treatment. The enhancement in the photocatalytic property of CNT–TiO2 nanocomposites prepared at 80 A arc current followed by UV illumination may be ascribed to the quality of CNTs produced at this current, as was reported before.

Enhanced photoelectrocatalytic performance for degradation of diclofenac and mechanism with TiO2 nano-particles decorated TiO2 nano-tubes arrays photoelectrode

International Nuclear Information System (INIS)

Cheng, Xiuwen; Liu, Huiling; Chen, Qinghua; Li, Junjing; Wang, Pu

2013-01-01

In this study, TiO 2 nano-particles decorated TiO 2 nano-tubes arrays (TiO 2 NPs/TiO 2 NTAs) photoelectrodes have been successfully prepared through anodization, combined with ultrasonic strategy, followed by annealing post-treatment. The morphology and structure of the as-prepared TiO 2 NPs/TiO 2 NTAs photoelectrodes were characterized by scanning electrons microscopy (SEM), N 2 adsorption/desorption isotherms, X-ray diffraction (XRD) and UV–visible light diffuse reflection spectroscopy (DRS). In addition, the generation of hydroxyl radicals (·OH) was detected by a photoluminescence (PL) spectra using terephthalic acid (TA) as a probe molecule. Furthermore, the photoelectrochemical (PECH) properties of TiO 2 NPs/TiO 2 NTAs photoanode were investigated through transient open circuit potential (OCP), photocurrent response (PCR) and electrochemical impedance spectroscopy (EIS). It was found that TiO 2 NPs/TiO 2 NTAs photoelectrode exhibited a distinct decrease of OCP of −0.219 mV cm −2 and PCR of 0.049 mA cm −2 , while a significantly enhanced photoelectrocatalytic (PEC) efficiency of 63.6% (0.4 V vs. SCE) for the degradation of diclofenac. Moreover, the enhanced PEC mechanism of TiO 2 NPs/TiO 2 NTAs photoanode was proposed. The high PEC performance could be attributed to the decoration of TiO 2 NPs, which could improve the mobility and separation efficiency of photoinduced charge carriers under external potential

The influence of Ti doping and annealing on Ce{sub 2}Ti{sub 2}O{sub 7} flash memory devices

Energy Technology Data Exchange (ETDEWEB)

Kao, Chyuan Haur [Department of Electronic Engineering, Chang Gung University, No. 259, Wenhua 1st Rd., Guishan Dist., Taoyuan City 33302, Taiwan, ROC (China); Kidney Research Center, Department of Nephrology, Chang Gung Memorial Hospital, Chang Gung University, College of Medicine, Taoyuan, Taiwan, ROC (China); Department of Electronic Engineering, Ming Chi University of Technology, Taiwan, ROC (China); Chen, Su Zhien [Department of Electronic Engineering, Chang Gung University, No. 259, Wenhua 1st Rd., Guishan Dist., Taoyuan City 33302, Taiwan, ROC (China); Kidney Research Center, Department of Nephrology, Chang Gung Memorial Hospital, Chang Gung University, College of Medicine, Taoyuan, Taiwan, ROC (China); Luo, Yang; Chiu, Wang Ting; Chiu, Shih Wei; Chen, I Chien [Department of Applied Materials and Optoelectronic Engineering, National Chi Nan University, No. 1, University Rd., Puli, Nantou Country 54561, Taiwan, ROC (China); Lin, Chan-Yu [Kidney Research Center, Department of Nephrology, Chang Gung Memorial Hospital, Chang Gung University, College of Medicine, Taoyuan, Taiwan, ROC (China); Chen, Hsiang, E-mail: hchen@ncnu.edu.tw [Department of Applied Materials and Optoelectronic Engineering, National Chi Nan University, No. 1, University Rd., Puli, Nantou Country 54561, Taiwan, ROC (China)

2017-02-28

Highlights: • Ce{sub 2}Ti{sub 2}O{sub 7} flash memories have been fabricated. • Material quality can be improved by annealing. • The memory performance can be enhanced by Ti doping. • Ti doping and annealing can reinforce crystallization. - Abstract: In this research, a CeO{sub 2} film with Ti doping was used as a trapping layer in metal oxide high-K-oxide-Si (MOHOS)-type memory devices. Since incorporation of Ti atoms into the film could fix dangling bonds and defects, the Ce{sub 2}Ti{sub 2}O{sub 7} trapping layer with annealing treatment could have a larger memory window and a faster programming/erasing speed. To confirm the origin, multiple material analyses indicate that annealing at an appropriate temperature and Ti doping could enhance crystallization. The Ce{sub 2}Ti{sub 2}O{sub 7}-based memory device is promising for future industrial flash memory applications.

High quantum yield graphene quantum dots decorated TiO_2 nanotubes for enhancing photocatalytic activity

International Nuclear Information System (INIS)

Qu, Ailan; Xie, Haolong; Xu, Xinmei; Zhang, Yangyu; Wen, Shengwu; Cui, Yifan

2016-01-01

Highlights: • High concentration yellow GQDs and TiO_2 nanotubes were achieved by a simple and green method. • High quantum yield GQDs enhanced the photodegradation capacity of TiO_2 nanotube. • The catalytic performance of GQDs/TiO_2 depends on the GQDs loading. • The improved photocatalytic activity of GQDs/TiO_2 was attributed to three aspects. - Abstract: Graphene quantum dots (GQDs) with high quantum yield (about 23.6% at an excitation wavelength of 320 nm) and GQDs/TiO_2 nanotubes (GQDs/TiO_2 NTs) composites were achieved by a simple hydrothermal method at low temperature. Photoluminescence characterization showed that the GQDs exhibited the down-conversion PL features at excitation from 300 to 420 nm and up-conversion photoluminescence in the range of 600–800 nm. The photocatalytic activity of prepared GQDs/TiO_2 NTs composites on the degradation of methyl orange (MO) was significantly enhanced compared with that of pure TiO_2 nanotubes (TiO_2 NTs). For the composites coupling with 1.5%, 2.5% and 3.5% GQDs, the degradation of MO after 20 min irradiation under UV–vis light irradiation (λ = 380–780 nm) were 80.52%, 94.64% and 51.91%, respectively, which are much higher than that of pure TiO_2 NTs (35.41%). It was inferred from the results of characterization that the improved photocatalytic activity of the GQDs/TiO_2 NTs composites was attributed to the synergetic effect of up-conversion properties of the GQDs, enhanced visible light absorption and efficient separation of photogenerated electron-holes of the GQDs/TiO_2 composite.

Enhanced oxidation of naphthalene using plasma activation of TiO2/diatomite catalyst.

Science.gov (United States)

Wu, Zuliang; Zhu, Zhoubin; Hao, Xiaodong; Zhou, Weili; Han, Jingyi; Tang, Xiujuan; Yao, Shuiliang; Zhang, Xuming

2018-04-05

Non-thermal plasma technology has great potential in reducing polycyclic aromatic hydrocarbons (PAHs) emission. But in plasma-alone process, various undesired by-products are produced, which causes secondary pollutions. Here, a dielectric barrier discharge (DBD) reactor has been developed for the oxidation of naphthalene over a TiO 2 /diatomite catalyst at low temperature. In comparison to plasma-alone process, the combination of plasma and TiO 2 /diatomite catalyst significantly enhanced naphthalene conversion (up to 40%) and CO x selectivity (up to 92%), and substantially reduced the formation of aerosol (up to 90%) and secondary volatile organic compounds (up to near 100%). The mechanistic study suggested that the presence of the TiO 2 /diatomite catalyst intensified the electron energy in the DBD. Meantime, the energized electrons generated in the discharge activated TiO 2 , while the presence of ozone enhanced the activity of the TiO 2 /diatomite catalyst. This plasma-catalyst interaction led to the synergetic effect resulting from the combination of plasma and TiO 2 /diatomite catalyst, consequently enhanced the oxidation of naphthalene. Importantly, we have demonstrated the effectiveness of plasma to activate the photocatalyst for the deep oxidation of PAH without external heating, which is potentially valuable in the development of cost-effective gas cleaning process for the removal of PAHs in vehicle applications during cold start conditions. Copyright © 2017 Elsevier B.V. All rights reserved.

Optimized dispersion of conductive agents for enhanced Li-storage performance of TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Han, Moyan; Chen, Ge, E-mail: chenge@bjut.edu.cn

2016-12-01

Highlights: • A novel TiO{sub 2}/carbon (TiO{sub 2}/C) composite has been synthesized by a layer-by-layer deposition method combined with electrostatic interaction. • As anode materials for Li-ion batteries, the TiO{sub 2}/C composites exhibit excellent rate capability and cycling stability. • The enhanced electrochemical performance may be attributed to the well-dispersed carbon conductive framework. - Abstract: Novel TiO{sub 2}/carbon (TiO{sub 2}/C) composites have been synthesized by a layer-by-layer deposition method, with electrostatic interaction. The addition of carbon conductive agents enhances the electrochemical performance of TiO{sub 2}. Carbon for these has been sourced 0D nitrogen-doped carbon, 1D carbon nanotubes and 2D graphene. The as-obtained TiO{sub 2}/C composites show carbon nanotubes and titanium dioxide coaxial nanocables anchored on the graphene. The nitrogen-doped carbon is uniformly dispersed on the nanocables. As anode materials for Li-ion batteries, the TiO{sub 2}/C composites exhibit excellent rate capability and cycling stability. A capacity of 150 mAh/g is retained at a current density of 4 A/g. The enhanced electrochemical performance may be attributed to the well-dispersed carbon conductive framework, which facilitates charge transfer during the lithium insertion/extraction process.

Enhancing the high temperature capability of Ti-alloys

Energy Technology Data Exchange (ETDEWEB)

Donchev, Alexander; Schuetze, Michael [DECHEMA-Forschungsinstitut, Frankfurt/Main (Germany); Kolitsch, Andreas; Yankov, Rossen [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Ion Beam Physics and Materials Research, Dresden (Germany)

2012-08-15

Titanium is a widely used structural material for applications below approximately 500 C but right now it cannot be used at higher temperatures. Titanium forms a fast growing rutile layer under these conditions. Furthermore enhanced oxygen uptake into the metal subsurface zone leads to embrittlement which deteriorates the mechanical properties. To overcome this problem a combined Al- plus F-treatment was developed. The combination of Al-enrichment in the surface zone so that intermetallic Ti{sub x}Al{sub y}-layers are produced which form a protective alumina layer during high temperature exposure plus stabilization of the Al{sub 2}O{sub 3}-scale by the fluorine effect led to significantly improved resistance against increased oxidation and embrittlement in high temperature exposure tests of several Ti-alloys. In this paper, the experimental procedures and achieved improvements are described. The results will be discussed for the use of Ti-alloys at elevated temperatures. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Uniform Gold-Nanoparticle-Decorated {001}-Faceted Anatase TiO2 Nanosheets for Enhanced Solar-Light Photocatalytic Reactions.

Science.gov (United States)

Shi, Huimin; Zhang, Shi; Zhu, Xupeng; Liu, Yu; Wang, Tao; Jiang, Tian; Zhang, Guanhua; Duan, Huigao

2017-10-25

The {001}-faceted anatase TiO 2 micro-/nanocrystals have been widely investigated for enhancing the photocatalysis and photoelectrochemical performance of TiO 2 nanostructures, but their practical applications still require improved energy conversion efficiency under solar-light and enhanced cycling stability. In this work, we demonstrate the controlled growth of ultrathin {001}-faceted anatase TiO 2 nanosheets on flexible carbon cloth for enhancing the cycling stability, and the solar-light photocatalytic performance of the synthesized TiO 2 nanosheets can be significantly improved by decorating with vapor-phase-deposited uniformly distributed plasmonic gold nanoparticles. The fabricated Au-TiO 2 hybrid system shows an 8-fold solar-light photocatalysis enhancement factor in photodegrading Rhodamine B, a high photocurrent density of 300 μA cm -2 under the illumination of AM 1.5G, and 100% recyclability under a consecutive long-term cycling measurement. Combined with electromagnetic simulations and systematic control experiments, it is believed that the tandem-type separation and transition of plasmon-induced hot electrons from Au nanoparticles to the {001} facet of anatase TiO 2 , and then to the neighboring {101} facet, is responsible for the enhanced solar-light photochemical performance of the hybrid system. The Au-TiO 2 nanosheet system addresses well the problems of the limited solar-light response of anatase TiO 2 and fast recombination of photogenerated electron-hole pairs, representing a promising high-performance recyclable solar-light-responding system for practical photocatalytic reactions.

Enhanced photocatalysts based on Ag-TiO2 and Ag-N-TiO2 nanoparticles for multifunctional leather surface coating

Directory of Open Access Journals (Sweden)

Gaidau Carmen

2016-01-01

Full Text Available The Ag deposition on TiO2 nanoparticles (Ag-TiO2 NPs and N-TiO2 nanoparticles (Ag-N-TiO2 NPs has been made by electrochemical methodology in view of improved antibacterial properties and enhanced photocatalytic activity under visible light irradiation. The particle size in powder and in dispersion showed similar values and good stability in aqueous medium which made them suitable for use in leather surface covering for new multifunctional properties development. The diffuse reflectance spectra of Ag-TiO2 NPs, Ag-N-TiO2 NPs and TiO2 NPs have been investigated and correlated with their photocatalytic performances under UV and visible light against different silver concentrations. The leather surfaces treated with Ag-N-TiO2 NPs showed advanced self-cleaning properties under visible light exposure through the hydrophilic mechanism of organic soil decomposition. Moreover the bacterial sensitivity and proven fungitoxic properties of Ag-N-TiO2 NPs leads to the possibility of designing new multifunctional additives to extend the advanced applications for more durable and useable materials.

Solvothermal preparation of micro/nanostructured TiO{sub 2} with enhanced lithium storage capability

Energy Technology Data Exchange (ETDEWEB)

Li, Jie [School of Physics and Mechanical & Electronical Engineering, Hubei University of Education, Wuhan, 430205 (China); Wang, Chao [Department of Architecture and Material Engineering, Hubei University of Education, Wuhan, 430205 (China); Zheng, Ping; Zhang, Lei; Chen, Gongxuan [College of Chemistry and Life Science, Hubei University of Education, Wuhan, 430205 (China); Tang, Chengchun [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Wu, Tian, E-mail: twu@whu.edu.cn [School of Physics and Mechanical & Electronical Engineering, Hubei University of Education, Wuhan, 430205 (China); College of Chemistry and Life Science, Hubei University of Education, Wuhan, 430205 (China); Department of Architecture and Material Engineering, Hubei University of Education, Wuhan, 430205 (China)

2017-04-01

Facile and controllable preparation of TiO{sub 2} is of prime importance to elaborately tailor and then fully exploit its intriguing functionalities in energy storage, catalysis and environmental remediation. Herein, a solvothermal method combined with post annealing is conducted, in which the hydrolysis of tetrabutyl titanate is controlled by the in-situ generated water during solvothermal treatment. By controlling synthetic conditions (i.e. reactant ratio, solvothermal temperature and reaction time), we manage to tailor the morphologies of TiO{sub 2}. Specially, three typical structures (nanoparticle, nanoneedle and nanorod) are studied to reveal the growth mechanism and the effects of the synthesis conditions. Nanoneedle-structured TiO{sub 2} shows higher specific capacity and enhanced cycle stability as anode material for lithium ion batteries. - Highlights: • Controllable preparation of nano-TiO{sub 2} is achieved by a solvothermal method. • TiO{sub 2} morphology is tailored by tuning reactant ratio, temperature and duration. • Needle structured TiO{sub 2} shows enhanced lithium storage capability.

Cellulose Acetate/N-TiO2 Biocomposite Flexible Films with Enhanced Solar Photochromic Properties

Science.gov (United States)

Radhika, T.; Anju, K. R.; Silpa, M. S.; Ramalingam, R. Jothi; Al-Lohedan, Hamad A.

2017-07-01

Flexible cellulose acetate/N-TiO2 nanocomposite films containing various concentrations of nanosized N-TiO2 and an intelligent methylene blue ink have been prepared by solution casting. The hydrothermally prepared nitrogen-doped titania (N-TiO2) and the films were characterized in detail. The photochromic properties of the prepared films were investigated under ultraviolet (UV), visible light, and simulated solar irradiation by UV-Vis spectrophotometry. Upon irradiation, the films exhibited rapid photochromic response that was reversible at room temperature. Films with higher content of nano N-TiO2 showed enhanced decoloration/recoloration under all irradiation conditions, with fast decoloration/recoloration under simulated solar irradiation. These results suggest that the amount of nano N-TiO2 in the composite, the concentration of methylene blue, and the solvent greatly influence the photochromic properties of the films. Such flexible and transparent cellulose acetate/N-TiO2 films with enhanced decoloration/recoloration properties under solar irradiation are promising smart materials for use in photoreversible printed electronics applications.

Characterization of Al-Ti phases in cycled TiF{sub 3}-enhanced Na{sub 2}LiAlH{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Nakamura, Y. [Department of Physics, Institute for Energy Technology, P.O. Box 40, NO-2027 Kjeller (Norway)]. E-mail: yumikon@ife.no; Fossdal, A. [Department of Physics, Institute for Energy Technology, P.O. Box 40, NO-2027 Kjeller (Norway); Brinks, H.W. [Department of Physics, Institute for Energy Technology, P.O. Box 40, NO-2027 Kjeller (Norway); Hauback, B.C. [Department of Physics, Institute for Energy Technology, P.O. Box 40, NO-2027 Kjeller (Norway)

2006-06-08

TiF{sub 3}-enhanced Na{sub 2}LiAlH{sub 6} was investigated after dehydrogenation-hydrogenation cycles by synchrotron X-ray diffraction. There was no sign of Ti after ball-milling with TiF{sub 3}, but two types of Al-Ti phases were observed in the cycled samples. In a sample after measuring five pressure-composition isotherms in the temperature range from 170 to 250 deg. C, a fcc phase with a = 3.987 A was observed. This phase is considered to be Al{sub 3}Ti with the L1{sub 2} structure. Samples after one or four cycles at selected temperatures between 170 and 250 deg. C showed diffraction from another fcc phase with a {approx} 4.03 A. This indicates formation of an Al{sub 1-y}Ti {sub y} solid-solution phase with y {approx} 0.15 similar to previously reported for cycled NaAlH{sub 4} with Ti additives.

Hydrogenated TiO{sub 2} film for enhancing photovoltaic properties of solar cells and self-sensitized effect

Energy Technology Data Exchange (ETDEWEB)

He, Hongcai; Yang, Kui; Wang, Ning, E-mail: ning-wang@uestc.edu.cn; Luo, Feifei; Chen, Haijun [State Key Laboratory of Electronic Thin Films and Integrated Devices and School of Microelectronics and Solid-State Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China)

2013-12-07

Hydrogenated TiO{sub 2} film was obtained by annealing TiO{sub 2} film at 350 °C for 2 h with hydrogen, and TiO{sub 2} films were prepared by screen printing on fluorine-doped tin oxide glass. Structural characterization by X-ray diffraction and electron microscopy did not show obvious difference between hydrogenated TiO{sub 2} film and pristine TiO{sub 2} film. Through optical and electrochemical characterization, the hydrogenated TiO{sub 2} film showed enhanced absorption and narrowed band gap, as well as reduced TiO{sub 2} surface impedance and dark current. As a result, an obviously enhanced photovoltaic effect was observed in the solar cell with hydrogenated TiO{sub 2} as photoanode without adding any dye due to the self-sensitized effect of hydrogenated TiO{sub 2} film, which excited electrons injecting internal conduction band of TiO{sub 2} to generate more photocurrent.

Chromate enhanced visible light driven TiO2 photocatalytic mechanism on Acid Orange 7 photodegradation

International Nuclear Information System (INIS)

Wang, Yeoung-Sheng; Shen, Jyun-Hong; Horng, Jao-Jia

2014-01-01

Highlights: • Photocatalysis of Cr(VI) and TiO 2 were studied by ESR analysis on DMPO-OH signals. • Mechanism of Cr(VI)-enhanced by visible light was different from that by UV. • O 2 adsorbed on TiO 2 surfaces could react with Cr(VI) to lower photoenergy needed. • Even by UV, no TiO 2 photocatalysis was observed without O 2 solution. • Visible light and Cr(VI) redox reaction could activate TiO 2 and would yield ·OH. - Abstract: When hexavalent chromium (Cr(VI)) is added to a TiO 2 photocatalytic reaction, the decolorization and mineralization efficiencies of azo dyes Acid Orange 7 (AO7) are enhanced even though the mechanism is unclear. This study used 5,5-dimethyl-L-pyrroline-N-oxide (DMPO) as the scavenger and the analysis of Electron Spin Resonance (ESR) to investigate this enhancement effect by observing the hydroxyl radical (·OH) generation of the Cr(VI)/TiO 2 system under UV and visible light (Vis) irradiation. With Cr(VI), the decolorization efficiencies were approximately 95% and 62% under UV and Vis, and those efficiencies were 25% less in the absence of Cr(VI). The phenomena of the DMPO-OH signals during the ESR analysis under Vis 405 and 550 nm irradiation were obviously the enhancement effects of Cr(VI) in aerobic conditions. In anoxic conditions, the catalytic effects of Cr(VI) could not be achieved due to the lack of a redox reaction between Cr(VI) and the adsorbed oxygen at the oxygen vacancy sites on the TiO 2 surfaces . The results suggest that by introducing the agents of redox reactions such as chromate ions, we could lower the photoenergy of TiO 2 needed and allow Vis irradiation to activate photocatalysis

Synthesis of spindle-shaped AgI/TiO{sub 2} nanoparticles with enhanced photocatalytic performance

Energy Technology Data Exchange (ETDEWEB)

Yang, Liu; Gao, Minggang; Dai, Bin; Guo, Xuhong; Liu, Zhiyong; Peng, Banghua, E-mail: banghuapeng@hotmail.com

2016-11-15

Highlights: • Nanoporous spindle-shaped AgI/TiO{sub 2} was synthesized by the solvothermal approach. • The spindle-shaped TiO{sub 2} was an excellent support for loading nanoparticles, such as AgI, transferring electrons quickly from AgI, which is beneficial for stabilizing the AgI. • AgI/TiO{sub 2} nanoparticles showed enhanced absorption intensity in the visible region and exhibited excellent photocatalytic activity. - Abstract: A novel synthetic route has been developed to prepare silver iodide (AgI) loaded spindle-shaped TiO{sub 2} nanoparticles (NPs). The morphology and crystallinity characterization revealed that small AgI NPs, with an average diameter of 15 nm were dispersed on the surface and interior of nanoporous anatase TiO{sub 2} support. High-resolution transmission electron microscopy (HRTEM), Brunauer-Emmett-Teller (BET) surface area, Raman and X-ray photoelectron spectroscopy (XPS) were used to identify the nanoporous structure of TiO{sub 2} and the existence of AgI NPs. Diffuse reflectance spectra (DRS) showed that AgI/TiO{sub 2} composite exhibited a remarkable enhancement of visible light absorption, which is ascribed to the addition of AgI. For illustrating the superior property of this hybrid as photocatalyst, the degradation experiments were carried out for processing rhodamine B (RhB) solution under visible light irradiation and it was found that the photocatalytic activity was dramatically improved for AgI/TiO{sub 2} compared with nanoporous TiO{sub 2} and commercial P25 TiO{sub 2}. The enhanced photocatalytic properties could be attributed to the large surface area of porous TiO{sub 2}, good stability of AgI particles, and the effective charge separation due to the synergetic effect between AgI and TiO{sub 2} that can facilitate the separation of electron-hole pairs. Our novel composite based on nanoporous spindle-shaped TiO{sub 2} represents a promising new pathway for the design of high-performance photocatalysts for environmental

Fabrication of TiO_2-modified polytetrafluoroethylene ultrafiltration membranes via plasma-enhanced surface graft pretreatment

International Nuclear Information System (INIS)

Qian, Yingjia; Chi, Lina; Zhou, Weili; Yu, Zhenjiang; Zhang, Zhongzhi; Zhang, Zhenjia; Jiang, Zheng

2016-01-01

Graphical abstract: - Highlights: • Multifunctional TiO_2/PAA/PTFE ultrafiltration membrane was fabricated via tight coating of TiO_2 functional layer onto the plasma-assisted graft of PAA on PTFE. • The high water flux rate, remarkable enhanced ultrafiltration performance and excellent self-cleaning ability were demonstrated. • The formation of COO−Ti bidentate coordination between TiO_2 and PAA was responsible for the successful coating. - Abstract: Surface hydrophilic modification of polymer ultrafiltration membrane using metal oxide represents an effective yet highly challenging solution to improve water flux and antifouling performance. Via plasma-enhanced graft of poly acryl acid (PAA) prior to coating TiO_2, we successfully fixed TiO_2 functional thin layer on super hydrophobic polytetrafluoroethylene (PTFE) ultrafiltration (UF) membranes. The characterization results evidenced TiO_2 attached on the PTFE-based UF membranes through the chelating bidentate coordination between surface-grafted carboxyl group and Ti"4"+. The TiO_2 surface modification may greatly reduce the water contact angle from 115.8° of the PTFE membrane to 35.0° without degradation in 30-day continuous filtration operations. The novel TiO_2/PAA/PTFE membranes also exhibited excellent antifouling and self-cleaning performance due to the intrinsic hydrophilicity and photocatalysis properties of TiO_2, which was further confirmed by the photo-degradation of MB under Xe lamp irradiation.

Enhanced Optical and Electrical Properties of TiO_2 Buffered IGZO/TiO_2 Bi-Layered Films

International Nuclear Information System (INIS)

Moon, Hyun-Joo; Kim, Daeil

2016-01-01

In and Ga doped ZnO (IGZO, 100-nm thick) thin films were deposited by radio frequency magnetron sputtering without intentional substrate heating on a bare glass substrate and a TiO_2-deposited glass substrate to determine the effect of the thickness of a thin TiO_2 buffer layer on the structural, optical, and electrical properties of the films. The thicknesses of the TiO_2 buffer layers were 5, 10 and 15 nm, respectively. As-deposited IGZO films with a 10 nm-thick TiO_2 buffer layer had an average optical transmittance of 85.0% with lower resistivity (1.83×10-2 Ω cm) than that of IGZO single layer films. The figure of merit (FOM) reached a maximum of 1.44×10-4 Ω-1 for IGZO/10 nm-thick TiO_2 bi-layered films, which is higher than the FOM of 6.85×10-5 Ω-1 for IGZO single layer films. Because a higher FOM value indicates better quality transparent conducting oxide (TCO) films, the IGZO/10 nm-thick TiO_2 bi-layered films are likely to perform better in TCO applications than IGZO single layer films.

Enhanced hardness in epitaxial TiAlScN alloy thin films and rocksalt TiN/(Al,Sc)N superlattices

Energy Technology Data Exchange (ETDEWEB)

Saha, Bivas [School of Materials Engineering, Purdue University, West Lafayette, Indiana 47907 (United States); Birck Nanotechnology Center, Purdue University, West Lafayette, Indiana 47907 (United States); Lawrence, Samantha K.; Bahr, David F. [School of Materials Engineering, Purdue University, West Lafayette, Indiana 47907 (United States); Schroeder, Jeremy L.; Birch, Jens [Thin Film Physics Division, Department of Physics, Chemistry, and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden); Sands, Timothy D. [School of Materials Engineering, Purdue University, West Lafayette, Indiana 47907 (United States); Birck Nanotechnology Center, Purdue University, West Lafayette, Indiana 47907 (United States); School of Electrical and Computer Engineering, Purdue University, West Lafayette, Indiana 47907 (United States)

2014-10-13

High hardness TiAlN alloys for wear-resistant coatings exhibit limited lifetimes at elevated temperatures due to a cubic-AlN to hexagonal-AlN phase transformation that leads to decreasing hardness. We enhance the hardness (up to 46 GPa) and maximum operating temperature (up to 1050 °C) of TiAlN-based coatings by alloying with scandium nitride to form both an epitaxial TiAlScN alloy film and epitaxial rocksalt TiN/(Al,Sc)N superlattices on MgO substrates. The superlattice hardness increases with decreasing period thickness, which is understood by the Orowan bowing mechanism of the confined layer slip model. These results make them worthy of additional research for industrial coating applications.

A p-n heterojunction of CuI/TiO2 with enhanced photoelectrocatalytic activity for methanol electro-oxidation

International Nuclear Information System (INIS)

Sun, Mingjuan; Hu, Jiayue; Zhai, Chunyang; Zhu, Mingshan; Pan, Jianguo

2017-01-01

Highlights: •A p-n heterojunction of CuI/TiO 2 is constructed. •CuI/TiO 2 is used as the support for depositing Pt nanoparticles. •Enhanced catalytic activity of MOR by using Pt-CuI/TiO 2 under light irradiation. •Improved charger separation contributes to enhanced photoelectrocatalytic activity. -- Abstract: In this paper, a p-n heterojunction including p-type CuI and n-type TiO 2 is first time constructed to be the support for the deposition of Pt. The as-prepared Pt-CuI/TiO 2 modified electrode is studied for the electrocatalytic oxidation of methanol both in dark and under light illumination. Compare to traditional electrocatalytic oxidation, the electrocatalytic activity of Pt-CuI/TiO 2 for methanol oxidation is improved with 4.0 times upon light illumination. Moreover, compare to bare CuI and TiO 2 upon light illumination, the heterostructure of CuI/TiO 2 displays 4.3 and 9.1 times enhanced electrocatalytic activity for methanol oxidation, respectively. The synergistic effects of photocatalysis and electrocatalysis as well as the effective charge transport in the p-n heterojunction of Pt-CuI/TiO 2 contribute such big enhancement. The present studies indicate that the constructing of p-n heterojunction provides more insights in the fields of photoelectrochemical and photo–assisted fuel cell system.

In situ growth of lamellar ZnTiO3 nanosheets on TiO2 tubular array with enhanced photocatalytic activity.

Science.gov (United States)

Cai, Yunyu; Ye, Yixing; Tian, Zhenfei; Liu, Jun; Liu, Yishu; Liang, Changhao

2013-12-14

We report a self-sacrificed in situ growth design toward preparation of ZnTiO3-TiO2 heterojunction structure. Highly reactive zinc oxide colloidal particles derived by laser ablation in liquids can react with TiO2 nanotubes to form a lamellar ZnTiO3 nanosheet structure in a hydrothermal-treatment process. Such hybrid structural product was characterized by X-ray diffraction, scanning and transmission electron microscopy, UV-vis diffuse reflection spectroscopy and X-ray photoelectron spectroscopy. The enhanced photocatalytic activity of the hybrid structure toward degradation of methyl orange (MO) and pentachlorophenol (PCP) molecules was demonstrated and compared with single phase TiO2, as a result of the efficient separation of light excited electrons and holes at the hetero-interfaces in the two semiconductors.

Enhancing the electrochemical performance of commercial TiO2 by eliminating sulfate radicals and coating carbon

International Nuclear Information System (INIS)

Wang, Li-Ying; Wu, Yan; Han, Jian-Ping; Zhang, Bo; Bai, Xue; Qi, Yong-Xin; Lun, Ning; Cao, Yu-Mei; Bai, Yu-Jun

2017-01-01

Highlights: •Commercial TiO 2 (c-TiO 2 ) exhibits poor electrochemical performance. •The performance of c-TiO 2 is improved by coating carbon at temperatures above 750 °C. •The removal of SO 4 2− and formation of carbon coating are responsible for the enhanced performance. -- Abstract: Despite the low price of commercial TiO 2 (c-TiO 2 ), the poor electrochemical performance restricts its practical application in Li-ion batteries, so clarifying the reasons and taking appropriate measures to improve the performance are of great significance. Herein, c-TiO 2 was coated with carbon at 600 and 750 °C using glucose as the carbon source. The product obtained at 750 °C exhibits markedly enhanced reversible capacities and outstanding rate performance compared to that obtained at 600 °C. In terms of the comparative experiments and detailed characterizations by several techniques, the SO 4 2− remained in the c-TiO 2 is the dominant impurity affecting the electrochemical performance mostly. The thorough decomposition of SO 4 2− at 750 °C and the formation of carbon coating give rise to the enhanced electronic and ionic conductivities of the c-TiO 2 , and thus are responsible for the significant improvement in the electrochemical performance. The easy fabrication and the low cost of the raw materials enable the carbon-coated c-TiO 2 to industrially apply in the LIBs.

SU-G-TeP3-15: Radiation Dose Enhancement by Anatase TiO2NPs

Energy Technology Data Exchange (ETDEWEB)

Youkhana, E; Geso, M; Feltis, B [RMIT University, Melbourne, VIC (Australia)

2016-06-15

Purpose: This work investigates radiation dose enhancement caused by TiO2 nanoparticles covering entire X-ray energy ranges used in radiation therapy. Methods: Anatase TiO2NPs crystal were synthesised and modified as hydrophilic and hydrophobic to disperse in culture-medium and halocarbons (PRESAGE chemical composition) respectively. TiO2NPs were characterised using TEM, XPS, XRD, TGA and FTIR. Various Concentrations have been utilised for determination of radiation-dose enhancement. This investigation is carried out in two ways; one using PRESAGE dosimeter/phantom and the other is radiobiological and based on in vitro study using two types of cell lines, Human Keratinocyte (HaCaT) and prostate cancer cell lines. The x-ray used are both kilovoltage and megavoltage separately. The prepared PRESAGE dosimeters were scanned using optical CT scanner. Clonogenic and MTS assays were employed for cell cytotoxicity and viability measurements for determination of the levels of dose enhancement. Results: Significant about (50%, 45%) dose enhancement by TiO2-NPs for kV x-rays is measured in both ways (Presage and Cells study). Slightly more is detected with the cells. However, the dose enhancement with megavoltage beams was insignificant using Presage and under same conditions the cells survival curves indicates around 20% which is relatively high. This difference can only be attributed to some biochemical effects. Such as generation of reactive oxygen species (ROS), this can affect the cells while it can’t be detected by Presage. Elevation of hydroxyl radicals (•OH) of many orders is observed with the inclusion of TiO2-NPs in cells-medium. Conclusion: Dose enhancement inflicted by TiO2-NPs is proven to be significant with megavoltage beams and minimal with kV. The high dose enhancements obtained can be attributed to higher levels of ROS generated. Since MV beams are most commonly used, this research proves potential value for more efficient beam delivery. This has

NaF-assisted hydrothermal synthesis of Ti-doped hematite nanocubes with enhanced photoelectrochemical activity for water splitting

Energy Technology Data Exchange (ETDEWEB)

Zheng, Chong; Zhu, Zezhou; Wang, Sibo; Hou, Yidong, E-mail: ydhou@fzu.edu.cn

2015-12-30

Graphical abstract: An enhanced photoelectrochemical activity for water splitting was achieved over porous Ti-doped α-Fe{sub 2}O{sub 3} nanocubes. - Highlights: . • Ti-doped hematite nanocubes were successfully prepared by NaF-assisted hydrothermal deposition and subsequent annealing. • Ti-doped α-Fe{sub 2}O{sub 3} nanocubes showed an enhanced PEC activity with an IPCE of 25.2% at 340 nm at 1.23 V vs. RHE. • The enhanced activity of Ti-doped hematite nanocubes can be ascribed to high surface area and fast charge transportation. - Abstract: Ti-doped α-Fe{sub 2}O{sub 3} nanocubes on FTO substrate was prepared by hydrothermal deposition β-FeOOH onto FTO glass with a solution of FeCl{sub 3}, TiOCl{sub 2} and NaF, followed by an appropriate annealing. In comparison to Ti-doped α-Fe{sub 2}O{sub 3} nanorods Ti-doped α-Fe{sub 2}O{sub 3} nanocubes showed an enhanced photoelectrochemical activity for water splitting, with a remarkable IPCE of 25.2% at 340 nm at the potential of 1.23 V vs. RHE. The hematite films were studied in detail by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, UV–vis absorption spectroscopy and electrochemical impedance spectroscopy. On the basis of the obtained results, the improved performance of Ti-doped α-Fe{sub 2}O{sub 3} nanocubes can be ascribed to the porous structure, good electrical conductivity and fast charge transportation of hematite.

Plasma-Sprayed ZnO/TiO2 Coatings with Enhanced Biological Performance

Science.gov (United States)

Zhao, Xiaobing; Peng, Chao; You, Jing

2017-08-01

Surface chemical composition and topography are two key factors in the biological performance of implants. The aim of this work is to deposit ZnO/TiO2 composite coatings on the surface of titanium substrates by plasma spraying technique. The effects of the amount of ZnO doping on the microstructure, surface roughness, corrosion resistance, and biological performance of the TiO2 coatings were investigated. The results indicated that the phase composition of the as-sprayed TiO2 coating was mainly rutile. Addition of 10% ZnO into TiO2 coating led to a slight shift of the diffraction peaks to lower angle. Anatase phase and Zn2TiO4 were formed in 20%ZnO/TiO2 and 30%ZnO/TiO2 coatings, respectively. Doping with ZnO changed the topography of the TiO2 coatings, which may be beneficial to enhance their biological performance. All coatings exhibited microsized surface roughness, and the corrosion resistance of ZnO/TiO2 coatings was improved compared with pure TiO2 coating. The ZnO/TiO2 coatings could induce apatite formation on their surface and inhibit growth of Staphylococcus aureus, but these effects were dose dependent. The 20%ZnO/TiO2 coating showed better biological performance than the other coatings, suggesting potential application for bone implants.

High quantum yield graphene quantum dots decorated TiO{sub 2} nanotubes for enhancing photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Qu, Ailan, E-mail: qal67@163.com; Xie, Haolong; Xu, Xinmei; Zhang, Yangyu; Wen, Shengwu; Cui, Yifan

2016-07-01

Highlights: • High concentration yellow GQDs and TiO{sub 2} nanotubes were achieved by a simple and green method. • High quantum yield GQDs enhanced the photodegradation capacity of TiO{sub 2} nanotube. • The catalytic performance of GQDs/TiO{sub 2} depends on the GQDs loading. • The improved photocatalytic activity of GQDs/TiO{sub 2} was attributed to three aspects. - Abstract: Graphene quantum dots (GQDs) with high quantum yield (about 23.6% at an excitation wavelength of 320 nm) and GQDs/TiO{sub 2} nanotubes (GQDs/TiO{sub 2} NTs) composites were achieved by a simple hydrothermal method at low temperature. Photoluminescence characterization showed that the GQDs exhibited the down-conversion PL features at excitation from 300 to 420 nm and up-conversion photoluminescence in the range of 600–800 nm. The photocatalytic activity of prepared GQDs/TiO{sub 2} NTs composites on the degradation of methyl orange (MO) was significantly enhanced compared with that of pure TiO{sub 2} nanotubes (TiO{sub 2} NTs). For the composites coupling with 1.5%, 2.5% and 3.5% GQDs, the degradation of MO after 20 min irradiation under UV–vis light irradiation (λ = 380–780 nm) were 80.52%, 94.64% and 51.91%, respectively, which are much higher than that of pure TiO{sub 2} NTs (35.41%). It was inferred from the results of characterization that the improved photocatalytic activity of the GQDs/TiO{sub 2} NTs composites was attributed to the synergetic effect of up-conversion properties of the GQDs, enhanced visible light absorption and efficient separation of photogenerated electron-holes of the GQDs/TiO{sub 2} composite.

Efficient silver modification of TiO2 nanotubes with enhanced photocatalytic activity

Science.gov (United States)

Huang, Jing; Ding, Lei; Xi, Yaoning; Shi, Liang; Su, Ge; Gao, Rongjie; Wang, Wei; Dong, Bohua; Cao, Lixin

2018-06-01

In this paper, Ag(CH3NH2)2+, Ag(NH3)2+ and Ag+ with different radii have been used as silver sources to find out the distribution of Ag ions on the H-TNT surface, which is critical to the final performance. The influence of this distribution on visible photocatalytic activity is further studied. The results indicate that, when Ag+ used as silver source with low concentration, these small sized silver ions mainly distribute on interlayer spacing of H-TNT. After heat-treatment and photo-reduction, the generated silver nanoparticles uniformly embed in the anatase TiO2 nanotube walls, and bring large interfacial area between Ag particles and TiO2 nanotubes. The separation effect of photogenerated electron-hole pair in TiO2 is enhanced by Ag particles, and achieves the best at 0.15 g/L, much higher than P25, TiO2/0, Ag-N@TiO2 and Ag-C-N@TiO2. This paper provides new ideas for the modification of TiO2 nanotubes.

Black TiO2 synthesized via magnesiothermic reduction for enhanced photocatalytic activity

Science.gov (United States)

Wang, Xiangdong; Fu, Rong; Yin, Qianqian; Wu, Han; Guo, Xiaoling; Xu, Ruohan; Zhong, Qianyun

2018-04-01

Utilizing solar energy for hydrogen evolution is a great challenge for its insufficient visible-light power conversion. In this paper, we report a facile magnesiothermic reduction of commercial TiO2 nanoparticles under Ar atmosphere and at 550 °C followed by acid treatment to synthesize reduced black TiO2 powders, which possesses a unique crystalline core-amorphous shell structure composed of disordered surface and oxygen vacancies and shows significantly improved optical absorption in the visible region. The unique core-shell structure and high absorption enable the reduced black TiO2 powders to exhibit enhanced photocatalytic activity, including splitting of water in the presence of Pt as a cocatalyst and degradation of methyl blue (MB) under visible light irradiation. Photocatalytic evaluations indicate that the oxygen vacancies play key roles in the catalytic process. The maximum hydrogen production rates are 16.1 and 163 μmol h-1 g-1 under the full solar wavelength range of light and visible light, respectively. This facile and versatile method could be potentially used for large scale production of colored TiO2 with remarkable enhancement in the visible light absorption and solar-driven hydrogen production.

Enhanced supercapacitor performances using C-doped porous TiO{sub 2} electrodes

Energy Technology Data Exchange (ETDEWEB)

Chen, Juanrong [School of Environment and Safety Engineering, Jiangsu University, Zhenjiang 212013 (China); Qiu, Fengxian, E-mail: fxqiuchem@163.com [School of Chemistry and Chemical Engineering, Jiangsu University, Zhenjiang 212013 (China); Zhang, Ying [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Liang, Jianzheng [School of Environment and Safety Engineering, Jiangsu University, Zhenjiang 212013 (China); Zhu, Huijun, E-mail: H.Zhu@cranfieldac.uk [School of Energy, Environmental Technology and Agrifood, Cranfield University, Bedfordshire MK43 0AL (United Kingdom); Cao, Shunsheng [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China)

2015-11-30

Graphical abstract: - Highlights: • A facile, cost-effective strategy was reported to prepare porous anatase TiO{sub 2} materials. • C-doped porous TiO{sub 2} (C/TiO{sub 2}) was in situ synthesized without the addition of carbon precursors. • C/TiO{sub 2} manifested an enhanced capacitance than the commercial P25. - Abstract: Considerable efforts have been paid to develop electrochemical capacitors with energy storage capability in order to meet the demands of multifunctional electronics. Here we report a facile method to fabricate C-doped porous anatase TiO{sub 2}. This technique involves the preparation of monodisperse cationic polystyrene nanoparticles (CPN), following sequential deposition of tetrabutylorthotitanate (TBT), and directly carbonizing of CPN. Interestingly, during the process of carbonizing CPN, a phase transition of TiO{sub 2} will be happened and whist C-doped porous anatase TiO{sub 2} is in situ formed. When this porous C-doped TiO{sub 2} is used as electrode material to prepare electrochemical capacitor, it manifests a higher capacitance than the commercial P25, effectively broadening it potential for many practical applications.

Nanoporous SiO{sub 2}/TiO{sub 2} coating with enhanced interfacial compatibility for orthopedic applications

Energy Technology Data Exchange (ETDEWEB)

Zhao, Xiaobing, E-mail: zhaoxiaobing00@163.com [School of Materials Science and Engineering, Changzhou University, Changzhou 213164 (China); Key Laboratory of Inorganic Coating Materials, Chinese Academy of Sciences, Shanghai 200050 (China); Jiangsu Key Laboratory of Materials Surface Science and Technology, Changzhou University, Changzhou 213164 (China); Cao, Hengchun; You, Jing; Cheng, Xingbao [School of Materials Science and Engineering, Changzhou University, Changzhou 213164 (China); Xie, Youtao [Key Laboratory of Inorganic Coating Materials, Chinese Academy of Sciences, Shanghai 200050 (China); Cao, Huiliang [State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Liu, Xuanyong, E-mail: xyliu@mail.sic.ac.cn [State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China)

2015-11-15

Graphical abstract: - Highlights: • The SiO{sub 2}/TiO{sub 2} coatings were fabricated on the cp-Ti substrates by plasma spraying. • Nanoporous topography was formed on SiO{sub 2}/TiO{sub 2} coating by HF-hydrothermal etching. • The hydrothermal conditions had important effects on the nanoporous topographies. • Nanoporous SiO{sub 2}/TiO{sub 2} coating exhibited enhanced cytocompatibility. - Abstract: Topographic modification in nanoscale is one of the most often used strategies to enhance the interfacial biocompatibility of implant materials. The aim of this work is to produce SiO{sub 2}/TiO{sub 2} coatings with nanoporous structures and favorable biological properties by atmospheric plasma spraying technology and subsequently hydrothermal etching method in hydrogen fluoride solution. The effects of hydrothermal time and temperature on the microstructures and osteoblast behavior of the SiO{sub 2}/TiO{sub 2} coatings were investigated. Results demonstrated that the as-sprayed SiO{sub 2}/TiO{sub 2} coating was mainly composed of rutile and quartz phases. After etching, nanoporous topographies were formed on the surface of the coatings and the hydrothermal parameters had important influences on the size and shape of the pores. The interconnected network pores on the coating surface could only produce at the appropriate hydrothermal conditions (the hydrothermal time and temperature were 60 min and 100 °C, respectively). Compared to TiO{sub 2} and SiO{sub 2}/TiO{sub 2} coatings, nanoporous SiO{sub 2}/TiO{sub 2} coatings could enhance osteoblast adhesion and promote cell proliferation. The results suggested the potential application of the porous coatings for enhancing the biological performance of the currently used dental and orthopedic implant materials.

Enhanced photoelectrochemical properties of TiO2 nanorod arrays decorated with CdS nanoparticles

International Nuclear Information System (INIS)

Xie, Zheng; Wang, Weipeng; Liu, Can; Li, Zhengcao; Liu, Xiangxuan; Zhang, Zhengjun

2014-01-01

TiO 2 nanorod arrays (TiO 2 NRAs) sensitized with CdS nanoparticles were fabricated via successive ion layer adsorption and reaction (SILAR), and TiO 2 NRAs were obtained by oxidizing Ti NRAs obtained through oblique angle deposition. The TiO 2 NRAs decorated with CdS nanoparticles exhibited excellent photoelectrochemical and photocatalytic properties under visible light, and the one decorated with 20 SILAR cycles CdS nanoparticles shows the best performance. This can be attributed to the enhanced separation of electrons and holes by forming heterojunctions of CdS nanoparticles and TiO 2 NRAs. This provides a promising way to fabricate the material for solar energy conversion and wastewater degradation. (paper)

Enhanced visible light photocatalytic degradation of methylene blue by F-doped TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Yu, Wei [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China); Liu, Xinjuan, E-mail: lxj669635@126.com [Shanghai Nanotechnlogy Promotion Center, Shanghai 200237 (China); Center for Coordination Bond and Electronic Engineering, College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Pan, Likun, E-mail: lkpan@phy.ecnu.edu.cn [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China); Li, Jinliang; Liu, Junying [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China); Zhang, Jing; Li, Ping; Chen, Chen [Shanghai Nanotechnlogy Promotion Center, Shanghai 200237 (China); Sun, Zhuo [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China)

2014-11-15

Graphical abstract: F-doped TiO2 is synthesized using a modified sol–gel method for visible photocatalytic degradation of MB with a high degradation rate of 91%. - Highlights: • F-doped TiO{sub 2} are synthesized using a modified sol–gel method. • The photocatalytic degradation of methylene blue by F-doped TiO{sub 2} is investigated. • A high methylene blue degradation rate of 91% is achieved under visible light irradiation. - Abstract: F-doped TiO{sub 2} (F-TiO{sub 2}) were successfully synthesized using a modified sol–gel method. The morphologies, structures, and photocatalytic performance in the degradation of methylene blue (MB) were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, UV–vis absorption spectroscopy, and electrochemical impedance spectra, respectively. The results show that F-TiO{sub 2} exhibits an enhanced photocatalytic performance in the degradation of MB with a maximum degradation rate of 91% under visible light irradiation as compared with pure TiO{sub 2} (32%). The excellent photocatalytic activity is due to the contribution from the increased visible light absorption, promoted separation of photo-generated electrons and holes as well as enhanced photocatalytic oxidizing species with the doping of F in TiO{sub 2}.

Nano-TiO2 enhances the toxicity of copper in natural water to Daphnia magna

International Nuclear Information System (INIS)

Fan Wenhong; Cui Minming; Liu Hong; Wang Chuan; Shi Zhiwei; Tan Cheng; Yang Xiuping

2011-01-01

The acute toxicity of engineered nanoparticles (NPs) in aquatic environments at high concentrations has been well-established. This study demonstrates that, at a concentration generally considered to be safe in the environment, nano-TiO 2 remarkably enhanced the toxicity of copper to Daphnia magna by increasing the copper bioaccumulation. Specifically, at 2 mg L -1 nano-TiO 2 , the (LC 50 ) of Cu 2+ concentration observed to kill half the population, decreased from 111 μg L -1 to 42 μg L -1 . Correspondingly, the level of metallothionein decreased from 135 μg g -1 wet weight to 99 μg g -1 wet weight at a Cu 2+ level of 100 μg L -1 . The copper was found to be adsorbed onto the nano-TiO 2 , and ingested and accumulated in the animals, thereby causing toxic injury. The nano-TiO 2 may compete for free copper ions with sulfhydryl groups, causing the inhibition of the detoxification by metallothioneins. - Research highlights: → This study demonstrates that, at a concentration generally considered to be safe in the environment, nano-TiO 2 remarkably enhanced the toxicity of copper to Daphnia magna. → The copper was found to be adsorbed onto the nano-TiO 2 , and ingested and accumulated in the Daphnia magna, thereby causing toxic injury. → The nano-TiO 2 may compete for free copper ions with sulfhydryl groups, causing the inhibition of the detoxification mechanism of metallothionein. - The nano-TiO 2 remarkably enhanced the toxicity of copper to Daphnia magna. The nano-TiO 2 may compete for free copper ions with sulfhydryl groups, causing the inhibition of the detoxification mechanism of metallothionein.

Generation of reactive oxygen species and charge carriers in plasmonic photocatalytic Au@TiO2 nanostructures with enhanced activity.

Science.gov (United States)

He, Weiwei; Cai, Junhui; Jiang, Xiumei; Yin, Jun-Jie; Meng, Qingbo

2018-06-13

The combination of semiconductor and plasmonic nanostructures, endowed with high efficiency light harvesting and surface plasmon confinement, has been a promising way for efficient utilization of solar energy. Although the surface plasmon resonance (SPR) assisted photocatalysis has been extensively studied, the photochemical mechanism, e.g. the effect of SPR on the generation of reactive oxygen species and charge carriers, is not well understood. In this study, we take Au@TiO2 nanostructures as a plasmonic photocatalyst to address this critical issue. The Au@TiO2 core/shell nanostructures with tunable SPR property were synthesized by the templating method with post annealing thermal treatment. It was found that Au@TiO2 nanostructures exhibit enhanced photocatalytic activity in either sunlight or visible light (λ > 420 nm). Electron spin resonance spectroscopy with spin trapping and spin labeling was used to investigate the enhancing effect of Au@TiO2 on the photo-induced reactive oxygen species and charge carriers. The formation of Au@TiO2 core/shell nanostructures resulted in a dramatic increase in light-induced generation of hydroxyl radicals, singlet oxygen, holes and electrons, as compared with TiO2 alone. This enhancement under visible light (λ > 420 nm) irradiation may be dominated by SPR induced local electrical field enhancement, while the enhancement under sunlight irradiation is dominated by the higher electron transfer from TiO2 to Au. These results unveiled that the superior photocatalytic activity of Au@TiO2 nanostructures correlates with enhanced generation of reactive oxygen species and charge carriers.

Enhancement of electron transfer from CdSe core/shell quantum dots to TiO2 films by thermal annealing

International Nuclear Information System (INIS)

Shao, Cong; Meng, Xiangdong; Jing, Pengtao; Sun, Mingye; Zhao, Jialong; Li, Haibo

2013-01-01

We demonstrated the enhancement of electron transfer from CdSe/ZnS core/shell quantum dots (QDs) to TiO 2 films via thermal annealing by means of steady-state and time-resolved photoluminescence (PL) spectroscopy. The significant decrease in PL intensities and lifetimes of the QDs on TiO 2 films was clearly observed after thermal annealing at temperature ranging from 100 °C to 300 °C. The obtained rates of electron transfer from CdSe core/shell QDs with red, yellow, and green emissions to TiO 2 films were significantly enhanced from several times to an order of magnitude (from ∼10 7 s −1 to ∼10 8 s −1 ). The improvement in efficiencies of electron transfer in the TiO 2 /CdSe QD systems was also confirmed. The enhancement could be considered to result from the thermal annealing reduced distance between CdSe QDs and TiO 2 films. The experimental results revealed that thermal annealing would play an important role on improving performances of QD based optoelectronic devices. -- Highlights: • Annealing-induced enhancement of electron transfer from CdSe to TiO 2 is reported. • CdSe QDs on TiO 2 and SiO 2 films are annealed at various temperatures. • Steady-state and time-resolved PL spectroscopy of CdSe QDs is studied. • The enhancement is related to the reduced distance between CdSe QDs and TiO 2

Fabrication and characterization of composite TiO{sub 2} nanotubes/boron-doped diamond electrodes towards enhanced supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Sobaszek, M. [Department of Metrology and Optoelectronics, Faculty of Electronics, Telecommunications and Informatics, Gdańsk University of Technology, 11/12 G. Narutowicza St., 80-233 Gdańsk (Poland); Siuzdak, K.; Sawczak, M. [Centre for Plasma and Laser Engineering, The Szewalski Institute of Fluid-Flow Machinery, Polish Academy of Sciences, 14 Fiszera St., 80-231 Gdansk (Poland); Ryl, J. [Department of Electrochemistry, Corrosion and Material Engineering, Faculty of Chemistry, Gdańsk University of Technology, 11/12 G. Narutowicza St., 80-233 Gdańsk (Poland); Bogdanowicz, R., E-mail: rbogdan@eti.pg.gda.pl [Department of Metrology and Optoelectronics, Faculty of Electronics, Telecommunications and Informatics, Gdańsk University of Technology, 11/12 G. Narutowicza St., 80-233 Gdańsk (Poland)

2016-02-29

The composite TiO{sub 2} nanotubes/boron-doped diamond electrodes were deposited using Microwave Plasma Enhanced Chemical Vapor Deposition resulting in the improved electrochemical performance. This composite electrode can deliver high specific capacitance of 7.46 mF cm{sup −2} comparing to boron-doped diamond (BDD) deposited onto flat Ti plate (0.11 mF cm{sup −2}).The morphology and composition of composite electrode were characterized by scanning electron microscopy, Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) techniques. According to XPS and Raman analyses, the structure of TiO{sub 2} was greatly changed during Chemical Vapor Deposition process: formation of Ti{sup 3+} sites, partial anatase to rutile transformation and titanium carbide phase formation. This effect is attributed to the simultaneous presence of activated hydrogen and carbon in the plasma leading to enhanced dehydration of NTs (nanotubes) followed by carbon bonding. The enhanced capacitive effect of TiO{sub 2} NT/BDD could be recognized as: (1) the unique synergistic morphology of NTs and BDD providing more efficient conducting pathway for the diffusion of ions and (2) partial decomposition of NTs and transformation towards to TiC and Ti{sub 2}O{sub 3} fractions. Finally, highly ordered titania nanotubes produced via simply, quick and controllable method — anodization, could act as promising substrate for conductive BDD layer deposition and further application of such composites for supercapacitor construction. - Highlights: • The TiO{sub 2} nanotube (NT)/diamond electrode delivers capacitance of 7.46 mF cm{sup −2}. • The NTs are not affected by diamond growth process and keep their pristine shape. • The BDD overlayer fully encapsulates TiO{sub 2} NTs exhibiting typical columnar growth. • The activated hydrogen and carbon in the plasma lead to enhanced dehydration of NTs. • The presence of TiC and Ti{sub 2}O{sub 3} fractions introducing additional capacitance.

Radiation-enhanced precipitation in a V-10 wt % Ti alloy

International Nuclear Information System (INIS)

Agarwal, S.C.; Taylor, A.

1976-01-01

A V-10 wt % Ti alloy was irradiated with 2.7 MeV 51 V + at 650 0 C to doses of 2 to 60 dpa. No void swelling was observed at any dose. The irradiation resulted in an enhancement of a precipitation process similar to that observed in unirradiated materials. The precipitates in irradiated specimens were found to have the NaCl-type cubic crystal structure with a lattice parameter of TiO. The orientation relationship between the matrix and the precipitates was the same as that observed under thermal equilibrium conditions in unirradiated materials

Plasmonic enhancement of visible-light water splitting with Au-TiO2 composite aerogels

Science.gov (United States)

Desario, Paul A.; Pietron, Jeremy J.; Devantier, Devyn E.; Brintlinger, Todd H.; Stroud, Rhonda M.; Rolison, Debra R.

2013-08-01

We demonstrate plasmonic enhancement of visible-light-driven splitting of water at three-dimensionally (3D) networked gold-titania (Au-TiO2) aerogels. The sol-gel-derived ultraporous composite nanoarchitecture, which contains 1 to 8.5 wt% Au nanoparticles and titania in the anatase form, retains the high surface area and mesoporosity of unmodified TiO2 aerogels and maintains stable dispersion of the ~5 nm Au guests. A broad surface plasmon resonance (SPR) feature centered at ~550 nm is present for the Au-TiO2 aerogels, but not Au-free TiO2 aerogels, and spans a wide range of the visible spectrum. Gold-derived SPR in Au-TiO2 aerogels cast as films on transparent electrodes drives photoelectrochemical oxidation of aqueous hydroxide and extends the photocatalytic activity of TiO2 from the ultraviolet region to visible wavelengths exceeding 700 nm. Films of Au-TiO2 aerogels in which Au nanoparticles are deposited on pre-formed TiO2 aerogels by a deposition-precipitation method (DP Au/TiO2) also photoelectrochemically oxidize aqueous hydroxide, but less efficiently than 3D Au-TiO2, despite having an essentially identical Au nanoparticle weight fraction and size distribution. For example, 3D Au-TiO2 containing 1 wt% Au is as active as DP Au/TiO2 with 4 wt% Au. The higher photocatalytic activity of 3D Au-TiO2 derives only in part from its ability to retain the surface area and porosity of unmodified TiO2 aerogel. The magnitude of improvement indicates that in the 3D arrangement either a more accessible photoelectrochemical reaction interphase (three-phase boundary) exists or more efficient conversion of excited surface plasmons into charge carriers occurs, thereby amplifying reactivity over DP Au/TiO2. The difference in photocatalytic efficiency between the two forms of Au-TiO2 demonstrates the importance of defining the structure of Au||TiO2 interfaces within catalytic Au-TiO2 nanoarchitectures.We demonstrate plasmonic enhancement of visible-light-driven splitting of

Enhanced thermoelectric performance of xMoS{sub 2}–TiS{sub 2} nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Ye, Yang; Wang, Yulong; Shen, YaWei [College of Materials Science and Engineering, Nanjing Tech University, Nanjing 210009 (China); Wang, Yifeng, E-mail: yifeng.wang@njtech.edu.cn [College of Materials Science and Engineering, Nanjing Tech University, Nanjing 210009 (China); Pan, Lin [College of Materials Science and Engineering, Nanjing Tech University, Nanjing 210009 (China); Tu, Rong [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Lu, Chunhua [College of Materials Science and Engineering, Nanjing Tech University, Nanjing 210009 (China); Huang, Rong [School of Information Science and Technology, East China Normal University, Shanghai 200062 (China); Koumoto, Kunihito [Toyota Physical and Chemical Research Institute, Nagakute 4801192 (Japan)

2016-05-05

A series of nanocomposite ceramics of micro-scale TiS{sub 2} containing MoS{sub 2} nanoparticles mainly embedded along grain boundaries were prepared and investigated attempting to enhance the thermoelectric performance of TiS{sub 2}. Results show that, compared with that of pristine TiS{sub 2} ceramic, the power factor of the composites was improved by virtues of enhanced Seebeck coefficient that should be brought out due to reduced carrier concentration and electron scattering or filtering at the MoS{sub 2}/matrix interfaces. Moreover, thanks to the significantly reduced thermal conductivity that originated from the intensified multi-scale phonon scattering and the decreased electronic contribution, a maximal ZT value of 0.29 at 573 K was obtained in the sample with 3 mol % MoS{sub 2}, which is 60% higher than that of pristine TiS{sub 2}. These findings promise nanocomposite as an effective approach to suppress its thermal conduction without degradation of power factor and thus to enhance the performance of TiS{sub 2}-based thermoelectrics. - Highlights: • Nanocomposites of TiS{sub 2} including nano-MoS{sub 2} were prepared by SPS. • Distribution of MoS{sub 2} mainly along the boundaries was confirmed. • Seebeck coefficient increased by reduced electron density with electron filtering. • Thermal conductivity decreased by suppressed phonon and electron transport. • A maximal ZT value of 0.29 was obtained at 573 K.

TiO2 Nanorods Decorated with Pd Nanoparticles for Enhanced Liquefied Petroleum Gas Sensing Performance.

Science.gov (United States)

Dhawale, Dattatray S; Gujar, Tanaji P; Lokhande, Chandrakant D

2017-08-15

Development of highly sensitive and selective semiconductor-based metal oxide sensor devices to detect toxic, explosive, flammable, and pollutant gases is still a challenging research topic. In the present work, we systematically enhanced the liquefied petroleum gas (LPG) sensing performance of chemical bath deposited TiO 2 nanorods by decorating Pd nanoparticle catalyst. Surface morphology with elemental mapping, crystal structure, composition and oxidation states, and surface area measurements of pristine TiO 2 and Pd:TiO 2 nanorods was examined by high resolution transmission electron microscopy with energy-dispersive X-ray spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and nitrogen adsorption-desorption characterization techniques. LPG sensing performance of pristine TiO 2 and Pd:TiO 2 nanorods was investigated in different LPG concentration and operating temperature ranges. The LPG response of 21% for pristine TiO 2 nanorods is enhanced to 49% after Pd catalyst decoration with reasonably fast response and recovery times. Further, the sensor exhibited long-term stability, which could be due to the strong metal support (Pd:TiO 2 ) interaction and catalytic properties offered by the Pd nanoparticle catalyst. The work described herein demonstrates a general and scalable approach that provides a promising route for rational design of variety of sensor devices for LPG detection.

Effect of different processes and Ti/Zn molar ratios on the structure, morphology, and enhanced photoelectrochemical and photocatalytic performance of Ti3+ self-doped titanium-zinc hybrid oxides

Science.gov (United States)

Fu, Rongrong; Wang, Qingyao; Gao, Shanmin; Wang, Zeyan; Huang, Baibiao; Dai, Ying; Lu, Jun

2015-07-01

Ti3+ self-doped titanium-zinc hybrid oxides with different phase compositions and morphologies were successfully synthesized using Zn powder as the reductant and Zn source by a chemical-reduction precipitation method with subsequent thermal treatment. The fabricated Ti3+ self-doped TiO2(A)/TiO2(R), TiO2(A)/TiO2(R)/ZnTiO3, and TiO2(A)/ZnO heterojunctions were characterized by X-ray diffraction, transmission electron microscopy, high-resolution transmission electron microscopy, X-ray photoelectron spectroscopy, and UV-Vis diffuse reflectance spectroscopy. The effects of various Ti/Zn molar ratios and preparation processes on the structural, morphological, optical, photocurrent and photocatalytic properties of the resultant samples were investigated systematically. Results reveal that Ti3+ self-doping enhances the photoabsorption capability of titanium-zinc hybrid oxides in the visible-light region. Moreover, different processes and Ti/Zn molar ratios play great influences on the structure, morphology, optical, photocurrent and photocatalytic properties of the final products. Ti3+ self-doped titanium-zinc hybrid oxides exhibit excellent photocurrent and photocatalytic activity than pure TiO2 and ZnTiO3 under visible-light irradiation (λ ≥ 400 nm). The most active Ti3+ self-doped titanium-zinc hybrid oxides photoanode presents significantly improved water splitting performance. The synergistic effect between the Ti3+ self-doped and heterojunctions is responsible for the enhanced performance of these materials.

Fabrication of TiO{sub 2}-modified polytetrafluoroethylene ultrafiltration membranes via plasma-enhanced surface graft pretreatment

Energy Technology Data Exchange (ETDEWEB)

Qian, Yingjia [School of Environmental Science and Engineering, Shanghai Jiaotong University, Shanghai 200240 (China); Chi, Lina, E-mail: lnchi@sjtu.edu.cn [School of Environmental Science and Engineering, Shanghai Jiaotong University, Shanghai 200240 (China); Faculty of Engineering and the Environment, University of Southampton, Southampton SO17 1BJ (United Kingdom); Zhou, Weili; Yu, Zhenjiang [School of Environmental Science and Engineering, Shanghai Jiaotong University, Shanghai 200240 (China); Zhang, Zhongzhi [College of Chemical Engineering, China University of Petroleum, Beijing 102249 (China); Zhang, Zhenjia [School of Environmental Science and Engineering, Shanghai Jiaotong University, Shanghai 200240 (China); Jiang, Zheng, E-mail: z.jiang@soton.ac.uk [Faculty of Engineering and the Environment, University of Southampton, Southampton SO17 1BJ (United Kingdom)

2016-01-01

Graphical abstract: - Highlights: • Multifunctional TiO{sub 2}/PAA/PTFE ultrafiltration membrane was fabricated via tight coating of TiO{sub 2} functional layer onto the plasma-assisted graft of PAA on PTFE. • The high water flux rate, remarkable enhanced ultrafiltration performance and excellent self-cleaning ability were demonstrated. • The formation of COO−Ti bidentate coordination between TiO{sub 2} and PAA was responsible for the successful coating. - Abstract: Surface hydrophilic modification of polymer ultrafiltration membrane using metal oxide represents an effective yet highly challenging solution to improve water flux and antifouling performance. Via plasma-enhanced graft of poly acryl acid (PAA) prior to coating TiO{sub 2}, we successfully fixed TiO{sub 2} functional thin layer on super hydrophobic polytetrafluoroethylene (PTFE) ultrafiltration (UF) membranes. The characterization results evidenced TiO{sub 2} attached on the PTFE-based UF membranes through the chelating bidentate coordination between surface-grafted carboxyl group and Ti{sup 4+}. The TiO{sub 2} surface modification may greatly reduce the water contact angle from 115.8° of the PTFE membrane to 35.0° without degradation in 30-day continuous filtration operations. The novel TiO{sub 2}/PAA/PTFE membranes also exhibited excellent antifouling and self-cleaning performance due to the intrinsic hydrophilicity and photocatalysis properties of TiO{sub 2}, which was further confirmed by the photo-degradation of MB under Xe lamp irradiation.

High-Quality Fe-doped TiO2 films with Superior Visible-Light Performance

DEFF Research Database (Denmark)

Su, Ren; Bechstein, Ralf; Kibsgaard, Jakob

2012-01-01

We report on high-quality polycrystalline Fe-doped TiO2 (Fe–TiO2) porous films synthesized via one-step electrochemical oxidation. We demonstrate that delicate properties such as the impurity concentration and the microstructure that strongly influence the performance of the material for photovol...

Plasma-induced synthesis of Pt nanoparticles supported on TiO2 nanotubes for enhanced methanol electro-oxidation

Science.gov (United States)

Su, Nan; Hu, Xiulan; Zhang, Jianbo; Huang, Huihong; Cheng, Jiexu; Yu, Jinchen; Ge, Chao

2017-03-01

A Pt/C/TiO2 nanotube composite catalyst was successfully prepared for enhanced methanol electro-oxidation. Pt nanoparticles with a particle size of 2 nm were synthesized by plasma sputtering in water, and anatase TiO2 nanotubes with an inner diameter of approximately 100 nm were prepared by a simple two-step anodization method and annealing process. Field-emission scanning electron microscopy images indicated that the different morphologies of TiO2 synthesized on the surface of Ti foils were dependent on the different anodization parameters. The electrochemical performance of Pt/C/TiO2 catalysts for methanol oxidation showed that TiO2 nanotubes were more suitable for use as Pt nanoparticle support materials than irregular TiO2 short nanorods due to their tubular morphology and better electronic conductivity. X-ray photoelectron spectroscopy characterization showed that the binding energies of the Pt 4f of the Pt/C/TiO2 nanotubes exhibited a slightly positive shift caused by the relatively strong interaction between Pt and the TiO2 nanotubes, which could mitigate the poisoning of the Pt catalyst by COads, and further enhance the electrocatalytic performance. Thus, the as-obtained Pt/C/TiO2 nanotubes composites may become a promising catalyst for methanol electro-oxidation.

Aligned TiO₂ nanotube/nanoparticle heterostructures with enhanced electrochemical performance as three-dimensional anode for lithium-ion microbatteries.

Science.gov (United States)

Xie, Keyu; Guo, Min; Lu, Wei; Huang, Haitao

2014-11-14

A novel TiO₂ three-dimensional (3D) anode with an aligned TiO₂ nanotube/nanoparticle heterostructure (TiO₂ NTs/NPs) is developed by simply immersing as-anodized TiO₂ NTs into water and further crystallizing the TiO₂ NTs by post-annealing. The heterostructure, with its core in a tubular morphology and with both the outer and inner surface consisting of nanoparticles, is confirmed by FESEM and TEM. A reversible areal capacity of 0.126 mAh · cm(-2) is retained after 50 cycles for the TiO₂ NTs/NPs heterostructure electrode, which is higher than that of the TiO₂ NTs electrode (0.102 mAh · cm(-2) after 50 cycles). At the current densities of 0.02, 0.04, 0.06, 0.08, 0.10 and 0.20 mA · cm(-2), the areal capacities are 0.142, 0.127, 0.117, 0.110, 0.104 and 0.089 mAh · cm(-2), respectively, for the TiO₂ NTs/NPs heterostructure electrode compared to the areal capacities of 0.123, 0.112, 0.105, 0.101, 0.094 and 0.083 mAh · cm(-2), respectively, for the the TiO₂ NTs electrode. The enhanced electrochemical performance is attributed to the unique microstructure of the TiO₂ NTs/NPs heterostructure electrode with the TiO₂ NT core used as a straight pathway for electronic transport and with TiO₂ NP offering enhanced surface areas for facile Li+ insertion/extraction. The results described here inspire a facile approach to fabricate a 3D anode with an enhanced electrochemical performance for lithium-ion microbattery applications.

Mo-doped Gray Anatase TiO2: Lattice Expansion for Enhanced Sodium Storage

International Nuclear Information System (INIS)

Liao, Hanxiao; Xie, Lingling; Zhang, Yan; Qiu, Xiaoqing; Li, Simin; Huang, Zhaodong; Hou, Hongshuai; Ji, Xiaobo

2016-01-01

Gray-colored Mo 6+ -doped anatase TiO 2 is prepared uniformly with particle size of 10–20 nm, and is firstly employed as anode material in sodium-ion batteries (SIBs), presenting excellent electrochemical performances. It delivered reversible specific capacities of 231.8 mAh g −1 at 0.1 C (33.5 mA g −1 ) after 100 cycles and 108.3 mAh g −1 at 5 C (1.68 A g −1 ), comparing to 170.5 mAh g −1 at 0.1 C and only 41.7 mAh g −1 at 5C for the bare TiO 2 . The improved electrochemical performances might be beneficial from the doping of Mo 6+ , which can effectively enhance the conductivity of TiO 2 resulting from induced conduction band electrons, interstitial oxygen defects and vacancies. In addition, the doping can also lead to the lattice expansion, which can facilitate the diffusion of Na + . In combination with natural abundance and environmental benignity, Mo 6+ -doped TiO 2 can be expected to be utilized as an anode material for enhanced sodium storage.

Enhanced photosensitized degradation of rhodamine B on CdS/TiO{sub 2} nanocomposites under visible light irradiation

Energy Technology Data Exchange (ETDEWEB)

Li, Wenjuan [Jiangsu Key Laboratory of Atmospheric Environment Monitoring and Pollution Control, School of Environmental Sciences and Engineering, Nanjing University of Information Sciences and Engineering, Nanjing 210044 (China); Research Institute of Photocatalysis, State Key Laboratory Breeding Base of Photocatalysis, Fuzhou University, Fuzhou 350002 (China); Shandong Province Key Laboratory of Life-Organic Analysis, Qufu Normal University, Qufu 273165 (China); Cui, Xiaoli [Shandong Province Key Laboratory of Life-Organic Analysis, Qufu Normal University, Qufu 273165 (China); Wang, Peixian; Shao, Yu [Research Institute of Photocatalysis, State Key Laboratory Breeding Base of Photocatalysis, Fuzhou University, Fuzhou 350002 (China); Li, Danzhen, E-mail: dzli@fzu.edu.cn [Research Institute of Photocatalysis, State Key Laboratory Breeding Base of Photocatalysis, Fuzhou University, Fuzhou 350002 (China); Teng, Fei [Jiangsu Key Laboratory of Atmospheric Environment Monitoring and Pollution Control, School of Environmental Sciences and Engineering, Nanjing University of Information Sciences and Engineering, Nanjing 210044 (China)

2013-09-01

Graphical abstract: The photosensitized degradation of RhB was largely enhanced by the synergistic effect of the RhB and CdS/TiO{sub 2} nanocomposite. The composite of the two inorganic semiconductors with appropriate oxidation reduction energy levels enhanced the charge separation and extended the absorption response to visible region. - Highlights: • CdS/TiO{sub 2} nanocomposites were synthesized by a simple hydrothermal method. • Samples prepared at 200 °C, 12 h, CdS/TiO{sub 2} = 12% possessed the best activity. • The photosensitized degradation of RhB was largely enhanced by the composite. • The better activity was due to the synergistic effect of the RhB and CdS/TiO{sub 2}. - Abstract: Visible-light-driven photocatalysts, CdS/TiO{sub 2} nanocomposites were synthesized by a simple hydrothermal method. Their formation and structures were characterized by X-ray diffractometer, transmission electron microscopy, diffuse reflectance spectroscopy, and X-ray photoelectron spectroscopy. Taking rhodamine B (RhB) as a model, their photocatalytic activities in aqueous phase under visible light irradiation (420 < λ < 800 nm) were tested. The results showed that the composite of CdS and TiO{sub 2} with appropriate oxidation reduction energy levels enhanced the charge separation and extended the absorption response into visible light region. Thus, the photosensitized degradation of RhB was largely enhanced. The degradation mechanism was explored concretely.

Enhanced piezoelectricity in plastically deformed nearly amorphous Bi{sub 12}TiO{sub 20}-BaTiO{sub 3} nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Yu, Dan; Zhao, Minglei, E-mail: zhaoml@sdu.edu.cn; Wang, Chunlei; Wang, Lihai; Su, Wenbin; Gai, Zhigang; Wang, Chunming; Li, Jichao; Zhang, Jialiang [School of Physics, State Key Laboratory of Crystal Materials, Shandong University, Jinan 250100 (China)

2016-07-18

Bulk Bi{sub 12}TiO{sub 20}-BaTiO{sub 3} (BTO-BT) nanocomposites are fabricated through the high-temperature interfacial reaction between nanometer-sized BaTiO{sub 3} particles and melting Bi{sub 12}TiO{sub 20}. Although the obtained BTO-BT nanocomposites are nearly amorphous and display very weak ferroelectricity, they exhibit relatively strong piezoelectricity without undergoing the electrical poling process. The volume fraction of crystalline Bi{sub 12}TiO{sub 20} is reduced to less than 10%, and the piezoelectric constant d{sub 33} is enhanced to 13 pC/N. Only the presence of the macroscopic polar amorphous phases can explain this unusual thermal stable piezoelectricity. Combining the results from X-ray diffraction, Raman spectroscopy, and thermal annealing, it can be confirmed that the formation of macroscopic polar amorphous phases is closely related to the inhomogeneous plastic deformation of the amorphous Bi{sub 12}TiO{sub 20} during the sintering process. These results highlight the key role of plastically deformed amorphous Bi{sub 12}TiO{sub 20} in the Bi{sub 12}TiO{sub 20}-based polar composites, and the temperature gradient driven coupling between the plastic strain gradient and polarization in amorphous phases is the main poling mechanism for this special type of bulk polar material.

Synthesis and Characterization of CdS/TiO2-Montmorillonite Nanocomposite with Enhanced Visible-Light Absorption

Directory of Open Access Journals (Sweden)

Feng-shan Zhou

2014-01-01

Full Text Available Sodium montmorillonite (MMT was chosen as the carrier; a serial of CdS/TiO2-MMT nanocomposites with enhanced visible-light absorption ability was prepared by hydrothermal synthesis method combination with semiconductor compound modification method. The samples are characterized by X-ray diffraction (XRD, X-ray photoelectron spectroscopy (XPS, and ultraviolet visible (UV-Vis spectroscopy; the results showed that TiO2 and CdS nanoparticles were loaded on the surface of montmorillonite uniformly. N2 adsorption-desorption experiment showed that the specific surface area of TiO2/montmorillonite nanocomposite made by this method can reach 200 m2/g and pore-size distribution was from 4 to 6 nm; UV-Vis showed that the recombination of CdS and TiO2 enhanced visible-light absorption ability of samples of TiO2/montmorillonite and visible-light absorption ability increase with the increased of the adsorption of CdS.

Enhanced Photocatalytic Activity of La3+-Doped TiO2 Nanotubes with Full Wave-Band Absorption

Science.gov (United States)

Xia, Minghao; Huang, Lingling; Zhang, Yubo; Wang, Yongqian

2018-06-01

TiO2 nanotubes doped with La3+ were synthesized by anodic oxidation method and the photocatalytic activity was detected by photodegrading methylene blue. As-prepared samples improved the absorption of both ultraviolet light and visible light and have a great enhancement on the photocatalytic activity while contrasting with the pristine TiO2 nanotubes. A tentative mechanism for the enhancement of photocatalytic activity with full wave-band absorption is proposed.

The effectiveness of Ti implants as barriers to carbon diffusion in Ti implanted steel under CVD diamond deposition conditions

Energy Technology Data Exchange (ETDEWEB)

Weiser, P.S.; Prawer, S. [Melbourne Univ., Parkville, VIC (Australia). School of Physics; Hoffman, A. [Technion-Israel Inst. of Tech., Haifa (Israel). Dept. of Chemistry; Evan, P.J. [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia); Paterson, P.J.K. [Royal Melbourne Inst. of Tech., VIC (Australia)

1993-12-31

The growth of chemical vapour deposited (CVD) diamond onto iron based substrates complicated by preferential soot formation and carbon diffusion into the substrate [1], leading to poor quality films and poor adhesion. In the initial stages of exposure to a microwave plasma, a layer of graphite is rapidly formed on an untreated Fe based substrate. Once this graphite layer reaches a certain thickness, reasonable quality diamond nucleates and grows upon it. However, the diamond film easily delaminates from the substrate, the weak link being the graphitic layer. Following an initial success in using a TiN barrier layer to inhibit the formation of such a graphitic layer the authors report on attempts to use an implanted Ti layer for the same purpose. This work was prompted by observation that, although the TiN proved to be an extremely effective diffusion barrier, adhesion may be further enhanced by the formation of a TiC interface layer between the diamond film and the Fe substrate. 3 refs., 6 figs.

The effectiveness of Ti implants as barriers to carbon diffusion in Ti implanted steel under CVD diamond deposition conditions

International Nuclear Information System (INIS)

Weiser, P.S.; Prawer, S.; Paterson, P.J.K.

1993-01-01

The growth of chemical vapour deposited (CVD) diamond onto iron based substrates complicated by preferential soot formation and carbon diffusion into the substrate [1], leading to poor quality films and poor adhesion. In the initial stages of exposure to a microwave plasma, a layer of graphite is rapidly formed on an untreated Fe based substrate. Once this graphite layer reaches a certain thickness, reasonable quality diamond nucleates and grows upon it. However, the diamond film easily delaminates from the substrate, the weak link being the graphitic layer. Following an initial success in using a TiN barrier layer to inhibit the formation of such a graphitic layer the authors report on attempts to use an implanted Ti layer for the same purpose. This work was prompted by observation that, although the TiN proved to be an extremely effective diffusion barrier, adhesion may be further enhanced by the formation of a TiC interface layer between the diamond film and the Fe substrate. 3 refs., 6 figs

The effectiveness of Ti implants as barriers to carbon diffusion in Ti implanted steel under CVD diamond deposition conditions

Energy Technology Data Exchange (ETDEWEB)

Weiser, P S; Prawer, S [Melbourne Univ., Parkville, VIC (Australia). School of Physics; Hoffman, A [Technion-Israel Inst. of Tech., Haifa (Israel). Dept. of Chemistry; Evan, P J [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia); Paterson, P J.K. [Royal Melbourne Inst. of Tech., VIC (Australia)

1994-12-31

The growth of chemical vapour deposited (CVD) diamond onto iron based substrates complicated by preferential soot formation and carbon diffusion into the substrate [1], leading to poor quality films and poor adhesion. In the initial stages of exposure to a microwave plasma, a layer of graphite is rapidly formed on an untreated Fe based substrate. Once this graphite layer reaches a certain thickness, reasonable quality diamond nucleates and grows upon it. However, the diamond film easily delaminates from the substrate, the weak link being the graphitic layer. Following an initial success in using a TiN barrier layer to inhibit the formation of such a graphitic layer the authors report on attempts to use an implanted Ti layer for the same purpose. This work was prompted by observation that, although the TiN proved to be an extremely effective diffusion barrier, adhesion may be further enhanced by the formation of a TiC interface layer between the diamond film and the Fe substrate. 3 refs., 6 figs.

Solvothermal synthesis of hierarchical TiO{sub 2} nanostructures with tunable morphology and enhanced photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Fan, Zhenghua [School of Physics and Materials Science, Anhui University, Hefei 230601 (China); Meng, Fanming, E-mail: mrmeng@ahu.edu.cn [School of Physics and Materials Science, Anhui University, Hefei 230601 (China); Key laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116024 (China); Zhang, Miao [School of Physics and Materials Science, Anhui University, Hefei 230601 (China); Wu, Zhenyu [College of Chemistry & Chemical Engineering, Anhui University, Hefei 230601 (China); Sun, Zhaoqi; Li, Aixia [School of Physics and Materials Science, Anhui University, Hefei 230601 (China)

2016-01-01

Graphical abstract: - Highlights: • Hierarchical anatase TiO{sub 2} nanostructures with enhanced photocatalytic activity are synthesized by solvothermal method. • A mechanism for enhanced photocatalytic activity of chrysanthemum-like hierarchical TiO{sub 2} nanostructures is proposed. • A possible formation mechanism is suggested to explain the transformation from rose-like to chrysanthemum-like, and to sea-urchin-like. - Abstract: This paper presents controllable growth and photocatalytic activity of TiO{sub 2} hierarchical nanostructures by solvothermal method at different temperatures. It is revealed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) that the morphology of TiO{sub 2} can be effectively controlled as rose-like, chrysanthemum-like and sea-urchin-like only changing solvothermal temperature. BET surface area analysis confirms the presence of a mesoporous network in all the nanostructures, and shows high surface area at relatively high temperature. The photocatalytic activities of the photocatalysts are evaluated by the photodegradation of RhB under UV light irradiation. The TiO{sub 2} samples exhibit high activity on the photodegradation of RhB, which is higher than that of the commercial P25. The enhancement in photocatalytic performance can be attributed to the synergetic effect of the surface area, crystallinity, band gap and crystalline size.

Ternary composite of TiO2 nanotubes/Ti plates modified by g-C3N4 and SnO2 with enhanced photocatalytic activity for enhancing antibacterial and photocatalytic activity.

Science.gov (United States)

Faraji, Masoud; Mohaghegh, Neda; Abedini, Amir

2018-01-01

A series of g-C 3 N 4 -SnO 2 /TiO 2 nanotubes/Ti plates were fabricated via simple dipping of TiO 2 nanotubes/Ti in a solution containing SnCl 2 and g-C 3 N 4 nanosheets and finally annealing of the plates. Synthesized plates were characterized by various techniques. The SEM analysis revealed that the g-C 3 N 4 -SnO 2 nanosheets with high physical stability have been successfully deposited onto the surface of TiO 2 nanotubes/Ti plate. Photocatalytic activity was investigated using two probe chemical reactions: oxidative decomposition of acetic acid and oxidation of 2-propanol under irradiation. Antibacterial activities for Escherichia coli (E. coli) bacteria were also investigated in dark and under UV/Vis illuminations. Detailed characterization and results of photocatalytic and antibacterial activity tests revealed that semiconductor coupling significantly affected the photocatalyst properties synthesized and hence their photocatalytic and antibacterial activities. Modification of TiO 2 nanotubes/Ti plates with g-C 3 N 4 -SnO 2 deposits resulted in enhanced photocatalytic activities in both chemical and microbial systems. The g-C 3 N 4 -SnO 2 /TiO 2 nanotubes/Ti plate exhibited the highest photocatalytic and antibacterial activity, probably due to the heterojunction between g-C 3 N 4 -SnO 2 and TiO 2 nanotubes/Ti in the ternary composite plate and thus lower electron/hole recombination rate. Based on the obtained results, a photocatalytic and an antibacterial mechanism for the degradation of E. coli bacteria and chemical pollutants over g-C 3 N 4 -SnO 2 /TiO 2 nanotubes/Ti plate were proposed and discussed. Copyright © 2017 Elsevier B.V. All rights reserved.

Graphene-spindle shaped TiO2 mesocrystal composites: Facile synthesis and enhanced visible light photocatalytic performance

International Nuclear Information System (INIS)

Yang, Xiaofei; Qin, Jieling; Li, Yang; Zhang, Rongxian; Tang, Hua

2013-01-01

Highlights: • Graphene-TiO 2 mesocrystal composites were fabricated via a facile approach. • Graphene sheets were decorated with spindle-like TiO 2 mesocrystals. • Graphene causes enhanced light absorbance and visible light photocatalytic activity. • Oxygen-containing radicals are believed to responsible for its improved activity. -- Abstract: Graphene (GR)-TiO 2 mesocrystal composites were prepared by a facile template-free process based on the combination of sol–gel and solvothermal methods, and were characterized using field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), Raman spectroscopy, UV–vis diffuse reflectance spectroscopy (UV–vis DRS), nitrogen absorption and electron spin resonance (ESR). Visible light photocatalytic performance of GR-TiO 2 composites was evaluated for photocatalytic degradation of organic dye Rhodamine B. It was found that the amount of graphene oxide (GO) added obviously affects morphologies of TiO 2 mesocrystals and photocatalytic activities of as-prepared nanocomposites. Composites prepared in the presence of different amounts of GO all exhibit higher photocatalytic activity than pure TiO 2 mesocrystals and P25, the composite obtained by using 20 mg GO presents the most uniform TiO 2 mesocrystals in the composite and shows the highest photocatalytic efficiency. The mechanism for the generation of TiO 2 mesocrystals in the GR-TiO 2 composite is proposed and possible reasons for the enhancement in visible light photocatalytic efficiency are also discussed

Enhanced Optical and Electrical Properties of TiO{sub 2} Buffered IGZO/TiO{sub 2} Bi-Layered Films

Energy Technology Data Exchange (ETDEWEB)

Moon, Hyun-Joo; Kim, Daeil [University of Ulsan, Ulsan (Korea, Republic of)

2016-08-15

In and Ga doped ZnO (IGZO, 100-nm thick) thin films were deposited by radio frequency magnetron sputtering without intentional substrate heating on a bare glass substrate and a TiO{sub 2}-deposited glass substrate to determine the effect of the thickness of a thin TiO{sub 2} buffer layer on the structural, optical, and electrical properties of the films. The thicknesses of the TiO{sub 2} buffer layers were 5, 10 and 15 nm, respectively. As-deposited IGZO films with a 10 nm-thick TiO{sub 2} buffer layer had an average optical transmittance of 85.0% with lower resistivity (1.83×10-2 Ω cm) than that of IGZO single layer films. The figure of merit (FOM) reached a maximum of 1.44×10-4 Ω-1 for IGZO/10 nm-thick TiO{sub 2} bi-layered films, which is higher than the FOM of 6.85×10-5 Ω-1 for IGZO single layer films. Because a higher FOM value indicates better quality transparent conducting oxide (TCO) films, the IGZO/10 nm-thick TiO{sub 2} bi-layered films are likely to perform better in TCO applications than IGZO single layer films.

Employing Ti nano-powder dielectric to enhance surface characteristics in electrical discharge machining of AISI D2 steel

Energy Technology Data Exchange (ETDEWEB)

Marashi, Houriyeh, E-mail: houriyeh@marashi.co [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Center of Advanced Manufacturing and Materials Processing (AMMP), 50603 Kuala Lumpur (Malaysia); Sarhan, Ahmed A.D., E-mail: ah_sarhan@yahoo.com [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Center of Advanced Manufacturing and Materials Processing (AMMP), 50603 Kuala Lumpur (Malaysia); Department of Mechanical Engineering, Faculty of Engineering, Assiut University, Assiut 71516 (Egypt); Hamdi, Mohd [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Center of Advanced Manufacturing and Materials Processing (AMMP), 50603 Kuala Lumpur (Malaysia)

2015-12-01

Graphical abstract: - Highlights: • We proposed adding Ti nano-powder to dielectric in EDM. • Average and peak-valley surface roughness was improved by 35 and 40%, respectively. • Improvement of up to 69% in material removal rate was obtained. • Enhanced surface morphology and formation of shallower craters were observed. - Abstract: Manufacturing components with superior surface characteristics is challenging when electrical discharge machining (EDM) is employed for mass production. The aim of this research is to enhance the characteristics of AISI D2 steel surface machined with EDM through adding Ti nano-powder to dielectric under various machining parameters, including discharge duration (T{sub on}) and peak current (I). Surface roughness profilometer, FESEM and AFM analysis were utilized to reveal the machined surface characteristics in terms of surface roughness, surface morphology and surface micro-defects. Moreover, EDX analysis was performed in order to evaluate the atomic deposition of Ti nano-powder on the surface. The concentration of Ti nano-powder in dielectric was also examined using ESEM and EDX. According to the results, the addition of Ti nano-powder to dielectric notably enhanced the surface morphology and surface roughness at all machining parameters except T{sub on} = 340 μs. Of these parameters, maximum enhancement was observed at T{sub on} = 210 μs, where the material removal rate and average surface roughness improved by ∼69 and ∼35% for peak current of 6 and 12 A, respectively. Elemental analysis signified negligible Ti deposition on the machined surface while the atomic concentration of Ti was increased around the crack areas.

Growth kinetics and initial stage growth during plasma-enhanced Ti atomic layer deposition

CERN Document Server

Kim, H

2002-01-01

We have investigated the growth kinetics of plasma-enhanced Ti atomic layer deposition (ALD) using a quartz crystal microbalance. Ti ALD films were grown at temperatures from 20 to 200 deg. C using TiCl sub 4 as a source gas and rf plasma-produced atomic H as the reducing agent. Postdeposition ex situ chemical analyses of thin films showed that the main impurity is oxygen, mostly incorporated during the air exposure prior to analysis. The thickness per cycle, corresponding to the growth rate, was measured by quartz crystal microbalance as a function of various key growth parameters, including TiCl sub 4 and H exposure time, rf plasma power, and sample temperature. The growth rates were independent of TiCl sub 4 exposure above 1x10 sup 3 L, indicating typical ALD mode growth. The key kinetic parameters for Cl extraction reaction and TiCl sub 4 adsorption kinetics were obtained and the growth kinetics were modeled to predict the growth rates based upon these results. Also, the dependency of growth kinetics on d...

Controllable hydrothermal synthesis of rutile TiO2 hollow nanorod arrays on TiCl4 pretreated Ti foil for DSSC application

International Nuclear Information System (INIS)

Xi, Min; Zhang, Yulan; Long, Lizhen; Li, Xinjun

2014-01-01

Rutile TiO 2 nanorod arrays (TNRs) were achieved by hydrothermal process on TiCl 4 pretreated Ti foil. Subsequently, TNRs were hydrothermally etched in HCl solution to form hollow TiO 2 nanorod arrays (H-TNRs). The TiCl 4 pretreatment plays key roles in enhancement of Ti foil corrosion resistance ability and crystal nucleation introduction for TNRs growth. TNRs with desired morphology can be obtained by controlling TiCl 4 concentration and the amount of tetrabutyl titanate (TTB) accordingly. TNRs with the length of ∼1.5 μm and diameter of ∼200 nm, obtained on 0.15 M TiCl 4 pretreated Ti foil with 0.6 mL TTB, exhibits relatively higher photocurrent. The increased pore volume of the H-TNRs has contributed to the increased surface area which is benefit for Dye-Sensitized Solar Cells (DSSC) application. And the 180 °C-H-TNRs photoanode obtained from the 0.15-TiCl 4 -TNRs sample demonstrated 128.9% enhancement of photoelectric efficiency of DSSC compared to that of the original TNR photoanode. - Graphical abstract: Rutile hollow TiO 2 nanorod array photoanode obtained from original TiO 2 nanorod array photoanode by hydrothermal etching demonstrates enhanced photoelectric efficiency of DSSC. - Highlights: • TiO 2 nanorods are prepared via hydrothermal process on TiCl 4 -pretreated Ti foil. • Hollow TiO 2 nanorods are obtained by hydrothermal etching of TiO 2 nanorods. • TiCl 4 pretreatment plays a key role in protecting Ti foil from chemical corrosion. • Hollow TiO 2 nanorods photoanode shows enhanced photoelectric efficiency for DSSC

The high surface energy of NiO {110} facets incorporated into TiO{sub 2} hollow microspheres by etching Ti plate for enhanced photocatalytic and photoelectrochemical activity

Energy Technology Data Exchange (ETDEWEB)

Li, Jian; Cui, Hongzhi, E-mail: cuihongzhi1965@163.com; Song, Xiaojie; Wei, Na; Tian, Jian, E-mail: jiantian@sdust.edu.cn

2017-02-28

Highlights: • NiO/TiO{sub 2} hollow microspheres were fabricated by etching Ti plate. • The incorporated NiO nanoparticles exposed high surface energy {110} facets. • The p–n junction catalysts improved photoelectrochemical and photocatalytic activity. • Using this synthesis strategy, other mixed semiconducting metal oxide microspheres. - Abstract: We present a rational design for the controllable synthesis of NiO/TiO{sub 2} hollow microspheres (NTHMs) with Ti plate via a one-pot template-free synthesis strategy. Specifically, to enhance the formation of hollow microspheres, part of the titanium source is provided by the Ti plate. The hollow spherical NiO/TiO{sub 2} particles possess unique microstructural characteristics, namely, a higher specific surface area (∼65.82 m{sup 2} g{sup −1}), a larger mesoporous structure (∼7.79 nm), and hierarchical nanoarchitectures connected with mesopores within the shell (monodispersed size of ∼1 μm and shell thickness of ∼80 nm). In addition, as a cocatalyst for improved catalytic activity, the incorporated NiO nanoparticles with exposed high surface energy {110} facets displayed an outstanding performance. It has been proven that this facile nanostructure possesses remarkably high photoelectrochemical and photocatalytic activities. The main mechanism for enhancement of photocatalytic activity is attributed to the construction of p-n junctions with an inner electric field between TiO{sub 2} and NiO, which can dramatically enhance the separation efficiency of the photogenerated electron-hole pairs. This strategy could be applied to fabricate mixed metal oxide hollow microspheres toward the photoelectrochemical catalysis.

Enhanced photoelectrochemical and photocatalytic activity of WO3-surface modified TiO2 thin film

Science.gov (United States)

Qamar, Mohammad; Drmosh, Qasem; Ahmed, Muhammad I.; Qamaruddin, Muhammad; Yamani, Zain H.

2015-02-01

Development of nanostructured photocatalysts for harnessing solar energy in energy-efficient and environmentally benign way remains an important area of research. Pure and WO3-surface modified thin films of TiO2 were prepared by magnetron sputtering on indium tin oxide glass, and photoelectrochemical and photocatalytic activities of these films were studied. TiO2 particles were <50 nm, while deposited WO3 particles were <20 nm in size. An enhancement in the photocurrent was observed when the TiO2 surface was modified WO3 nanoparticles. Effect of potential, WO3 amount, and radiations of different wavelengths on the photoelectrochemical activity of TiO2 electrodes was investigated. Photocatalytic activity of TiO2 and WO3-modified TiO2 for the decolorization of methyl orange was tested.

Enhanced photocathodic protection performance of Ag/graphene/TiO2 composite for 304SS under visible light

Science.gov (United States)

Li, Hong; Wang, Xiutong; Wei, Qinyi; Liu, Xueqing; Qian, Zhouhai; Hou, Baorong

2017-06-01

Ag and graphene co-sensitized TiO2 composites were successfully fabricated and used as photoanodes for photogenerated cathodic protection of 304 stainless steel (304SS) under visible light. Graphene films was firstly deposited onto the TiO2 nanotube (NT) films via cyclic voltammetric electrodeposition. Ag/graphene/TiO2 films were then fabricated via dipping and photoreduction method. The morphology, composition and optical response of the Ag/graphene/TiO2 NT composites were characterized by scanning electron microscopy, x-ray diffraction, x-ray photoelectron spectroscopy, UV-vis diffusion reflectance spectroscopy, respectively. The photocathodic protection performance of the Ag/graphene/TiO2 composites were systematically studied through open-circuit potential and potentiodynamic polarization measurements in 3.5 wt% NaCl solution under visible light (λ > 400 nm). The composites exhibited enhanced photogenerated cathodic protection performance for 304SS under visible light irradiation compared to pure TiO2. Graphene and Ag have a synergistic effect on the enhancement of photocathodic protection performance of TiO2. The composites prepared with 30-cycle graphene film and 15 mM AgNO3 solution showed the optimal corrosion protection performance.

Efficiency enhancement of ZnO-based dye-sensitized solar cell by hollow TiO{sub 2} nanofibers

Energy Technology Data Exchange (ETDEWEB)

Li, Fengrong; Wang, Guangchao; Jiao, Yu [Faculty of Materials, Optoelectronics and Physics, Key Laboratory of Low Dimensional Materials and Application Technology of Ministry of Education, Xiangtan University, Xiangtan 411105, Hunan (China); Li, Jiangyu [Department of Mechanical Engineering, University of Washington, Seattle, WA 98195-2600 (United States); Xie, Shuhong, E-mail: shxie@xtu.edu.cn [Faculty of Materials, Optoelectronics and Physics, Key Laboratory of Low Dimensional Materials and Application Technology of Ministry of Education, Xiangtan University, Xiangtan 411105, Hunan (China)

2014-10-25

Highlights: • The hollow TiO{sub 2} nanofibers were synthesized by one step electrospinning method. • We studied the performance of DSSC with different TiO{sub 2} weight ratioes. • The hollow TiO{sub 2} nanofibers enhance light scattering and suppress electrons recombination. • The efficiency of DSSC improved from 2.82% to 4.59% by adding 10 wt.% of TiO{sub 2}. - Abstract: One-dimensional nanostructures as the photoanode of dye-sensitized solar cell (DSSC) can provide a direct transport pathway for electrons injection to increase electrons transfer efficiency. In this work, hollow TiO{sub 2} nanofibers were fabricated by one step electrospinning based on sol–gel method, and were used to successfully enhance the conversion efficiency of ZnO-based DSSC. The effects of different TiO{sub 2} weight percentages on the performance of TiO{sub 2}/ZnO composite photoanode were investigated systematically. The results indicate that the light scattering of the photoanode film is increased and the electrons recombination is suppressed when appropriate amount of hollow TiO{sub 2} nanofibers was added into ZnO. The maximal energy conversion efficiency reaches 4.59% by adding 10 wt.% of hollow TiO{sub 2} nanofibers, which is 62% higher than that of DSSC based on pure ZnO nanoparticles.

Enhanced visible light photocatalytic properties of Fe-doped TiO2 nanorod clusters and monodispersed nanoparticles

International Nuclear Information System (INIS)

Liu, Y.; Wei, J.H.; Xiong, R.; Pan, C.X.; Shi, J.

2011-01-01

In order to get photocatalysts with desired morphologies and enhanced visible light responses, the Fe-doped TiO 2 nanorod clusters and monodispersed nanoparticles were prepared by modified hydrothermal and solvothermal method, respectively. The microstructures and morphologies of TiO 2 crystals can be controlled by restraining the hydrolytic reaction rates. The Fe-doped photocatalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV-vis absorption spectroscopy (UV-vis), N 2 adsorption-desorption measurement (BET), and photoluminescence spectroscopy (PL). The refinements of the microstructures and morphologies result in the enhancement of the specific surface areas. The Fe 3+ -dopants in TiO 2 lattices not only lead to the significantly extending of the optical responses from UV to visible region but also diminish the recombination rates of the electrons and holes. The photocatalytic activities were evaluated by photocatalytic decomposition of formaldehyde in air under visible light illumination. Compared with P25 (TiO 2 ) and N-doped TiO 2 nanoparticles, the Fe-doped photocatalysts show high photocatalytic activities under visible light.

Plasmon-Sensitized Graphene/TiO2 Inverse Opal Nanostructures with Enhanced Charge Collection Efficiency for Water Splitting.

Science.gov (United States)

Boppella, Ramireddy; Kochuveedu, Saji Thomas; Kim, Heejun; Jeong, Myung Jin; Marques Mota, Filipe; Park, Jong Hyeok; Kim, Dong Ha

2017-03-01

In this contribution we have developed TiO 2 inverse opal based photoelectrodes for photoelectrochemical (PEC) water splitting devices, in which Au nanoparticles (NPs) and reduced graphene oxide (rGO) have been strategically incorporated (TiO 2 @rGO@Au). The periodic hybrid nanostructure showed a photocurrent density of 1.29 mA cm -2 at 1.23 V vs RHE, uncovering a 2-fold enhancement compared to a pristine TiO 2 reference. The Au NPs were confirmed to extensively broaden the absorption spectrum of TiO 2 into the visible range and to reduce the onset potential of these photoelectrodes. Most importantly, TiO 2 @rGO@Au hybrid exhibited a 14-fold enhanced PEC efficiency under visible light and a 2.5-fold enrichment in the applied bias photon-to-current efficiency at much lower bias potential compared with pristine TiO 2 . Incident photon-to-electron conversion efficiency measurements highlighted a synergetic effect between Au plasmon sensitization and rGO-mediated facile charge separation/transportation, which is believed to significantly enhance the PEC activity of these nanostructures under simulated and visible light irradiation. Under the selected operating conditions the incorporation of Au NPs and rGO into TiO 2 resulted in a remarkable boost in the H 2 evolution rate (17.8 μmol/cm 2 ) compared to a pristine TiO 2 photoelectrode reference (7.6 μmol/cm 2 ). In line with these results and by showing excellent stability as a photoelectrode, these materials are herin underlined to be of promising interest in the PEC water splitting reaction.

Preparation of Ni Doped ZnO-TiO2 Composites and Their Enhanced Photocatalytic Activity

Directory of Open Access Journals (Sweden)

Xiaowen Zou

2014-01-01

Full Text Available Herein, Ni doped ZnO-TiO2 composites were prepared by facile sol-gel approach and were characterized by X-ray diffraction (XRD, transmission electron microscopy (TEM, UV-visible diffuse reflectance spectroscopy (UV-Vis DRS, X-ray photoelectron spectroscopy (XPS, and photoluminescence spectroscopy (PL. The results indicated that the Ni ions can be incorporated into the lattice of TiO2 structure and replace Ti. The introduction of Ni expanded light absorption of TiO2 to visible region, increased amount of surface hydroxyl groups and physically adsorbed oxygen (as the electronic scavenges, and then enhanced separation rate of photogenerated carriers. The photodegradation test of reactive brilliant blue (KN-R under simulated solar light indicated that Ni doped ZnO-TiO2 composites have better photocatalytic activities, as compared to those of TiO2 and ZnO-TiO2.

Enhanced Photoelectrochemical Behavior of H-TiO2 Nanorods Hydrogenated by Controlled and Local Rapid Thermal Annealing.

Science.gov (United States)

Wang, Xiaodan; Estradé, Sonia; Lin, Yuanjing; Yu, Feng; Lopez-Conesa, Lluis; Zhou, Hao; Gurram, Sanjeev Kumar; Peiró, Francesca; Fan, Zhiyong; Shen, Hao; Schaefer, Lothar; Braeuer, Guenter; Waag, Andreas

2017-12-01

Recently, colored H-doped TiO 2 (H-TiO 2 ) has demonstrated enhanced photoelectrochemical (PEC) performance due to its unique crystalline core-disordered shell nanostructures and consequent enhanced conduction behaviors between the core-shell homo-interfaces. Although various hydrogenation approaches to obtain H-TiO 2 have been developed, such as high temperature hydrogen furnace tube annealing, high pressure hydrogen annealing, hydrogen-plasma assisted reaction, aluminum reduction and electrochemical reduction etc., there is still a lack of a hydrogenation approach in a controlled manner where all processing parameters (temperature, time and hydrogen flux) were precisely controlled in order to improve the PEC performance of H-TiO 2 and understand the physical insight of enhanced PEC performance. Here, we report for the first time a controlled and local rapid thermal annealing (RTA) approach to prepare hydrogenated core-shell H-TiO 2 nanorods grown on F:SnO 2 (FTO) substrate in order to address the degradation issue of FTO in the typical TiO 2 nanorods/FTO system observed in the conventional non-RTA treated approaches. Without the FTO degradation in the RTA approach, we systematically studied the intrinsic relationship between the annealing temperature, structural, optical, and photoelectrochemical properties in order to understand the role of the disordered shell on the improved photoelectrochemical behavior of H-TiO 2 nanorods. Our investigation shows that the improvement of PEC performance could be attributed to (i) band gap narrowing from 3.0 to 2.9 eV; (ii) improved optical absorption in the visible range induced by the three-dimensional (3D) morphology and rough surface of the disordered shell; (iii) increased proper donor density; (iv) enhanced electron-hole separation and injection efficiency due to the formation of disordered shell after hydrogenation. The RTA approach developed here can be used as a suitable hydrogenation process for TiO 2 nanorods

Enhancement of tributyltin degradation under natural light by N-doped TiO2 photocatalyst

International Nuclear Information System (INIS)

Bangkedphol, S.; Keenan, H.E.; Davidson, C.M.; Sakultantimetha, A.; Sirisaksoontorn, W.; Songsasen, A.

2010-01-01

Photo-degradation of tributyltin (TBT) has been enhanced by TiO 2 nanoparticles doped with nitrogen (N-doped TiO 2 ). The N-doped catalyst was prepared by a sol-gel reaction of titanium (IV) tetraisopropoxide with 25% ammonia solution and calcined at various temperatures from 300 to 600 deg. C. X-ray diffraction results showed that N-doped TiO 2 remained amorphous at 300 deg. C. At 400 deg. C the anatase phase occurred then transformed to the rutile phase at 600 deg. C. The crystallite size calculated from Scherrer's equation was in the range of 16-51 nm which depended on the calcination temperature. N-doped TiO 2 calcined at 400 deg. C which contained 0.054% nitrogen, demonstrated the highest photocatalytic degradation of TBT at 28% in 3 h under natural light when compared with undoped TiO 2 and commercial photocatalyst, P25-TiO 2 which gave 14.8 and 18% conversion, respectively.

Photovoltaic performance enhancement of CdS quantum dot-sensitized TiO2 photoanodes with plasmonic gold nanoparticles

International Nuclear Information System (INIS)

Liu, Aiping; Ren, Qinghua; Zhao, Ming; Xu, Tao; Yuan, Ming; Zhao, Tingyu; Tang, Weihua

2014-01-01

Highlights: • CdS QD-sensitized TiO 2 porous photoanode with plasmonic gold. • A prominent light absorption enhancement of hybrid was attained by gold plasmon. • The photovoltaic response of hybrid was tunable by CdS amount. • The Au/TiO 2 /CdS hybrid had a potential application in energy conversion devices. -- Abstract: The CdS quantum dot-sensitized TiO 2 films with plasmonic gold nanoparticles were designed as photoanodes by the electrodeposition of gold combined with the “successive ionic layer adsorption and reaction” (SILAR) method for CdS deposition on porous TiO 2 films. A prominent enhancement in light absorption of Au/TiO 2 /CdS hybrid was attained by efficient light scattering of gold plasmons as sub-wavelength antennas and concentrators. The photogenerated electron formed in the near-surface region of TiO 2 and CdS were facilitated to transfer to the plasmonic gold, resulting in the enhancement of photocurrent and incident photon-to-current conversion efficiency of hybrid photoanode upon photoirradiation. Furthermore, the photovoltaic response of hybrid was highly tunable with respect to the number of SILAR cycles applied to deposit CdS. The thicker absorber layer with less porous structure and larger CdS crystals might limit the electrolyte diffusion into the hybrid electrode and impose a barrier for electron tunneling and transferring. The highly versatile and tunable properties of Au/TiO 2 /CdS photoanodes demonstrated their potential application in energy conversion devices

One-dimensional Z-scheme TiO{sub 2}/WO{sub 3}/Pt heterostructures for enhanced hydrogen generation

Energy Technology Data Exchange (ETDEWEB)

Gao, Hongqing [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); State Centre for International Cooperation on Designer Low-carbon and Environmental Materials (SCICDLCEM), Zhengzhou University, Zhengzhou 450001, Henan (China); Zhang, Peng, E-mail: Zhangp@zzu.edu.cn [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); State Centre for International Cooperation on Designer Low-carbon and Environmental Materials (SCICDLCEM), Zhengzhou University, Zhengzhou 450001, Henan (China); Hu, Junhua, E-mail: Hujh@zzu.edu.cn [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); State Centre for International Cooperation on Designer Low-carbon and Environmental Materials (SCICDLCEM), Zhengzhou University, Zhengzhou 450001, Henan (China); Pan, Jimin [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); Fan, Jiajie [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); State Centre for International Cooperation on Designer Low-carbon and Environmental Materials (SCICDLCEM), Zhengzhou University, Zhengzhou 450001, Henan (China); Shao, Guosheng [School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); State Centre for International Cooperation on Designer Low-carbon and Environmental Materials (SCICDLCEM), Zhengzhou University, Zhengzhou 450001, Henan (China); Institute for Renewable Energy and Environmental Technologies, University of Bolton, Bolton BL35AB (United Kingdom)

2017-01-01

Graphical abstract: We reported one-dimensional solid-state Z-scheme photosynthetic heterojunction system with Pt nanoparticle as an electron collector and WO{sub 3} as a hole collector, leading to effective charge separation. - Highlights: • The composite nanofibers were fabricated by facile electrospinning technique. • The composite nanofibers exhibited enhanced activity for H{sub 2} evolution. • Enhanced activity is due to the formation of Z-scheme TiO{sub 2}/WO{sub 3}/Pt heterojunction. - Abstract: One-dimensional Z-scheme TiO{sub 2}/WO{sub 3}/Pt heterostructures were fabricated by integrating a facile electrospinning technique and subsequent annealing in air. X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and UV–vis diffuse reflectance spectroscopy, were used to characterize the as-fabricated samples. The results showed that the H{sub 2}-generation of the as-fabricated one-dimensional Z-scheme TiO{sub 2}/WO{sub 3}/Pt heterostructures (S2) was greatly enhanced compared with pure TiO{sub 2} nanofibers (S0) and TiO{sub 2}/WO{sub 3} nanofibers (S1). The enhanced photocatalyst activities were mainly attributed to the solid-state Z-scheme photosynthetic heterojunction system with Pt nanoparticle as an electron collector and WO{sub 3} as a hole collector, leading to effective charge separation on these semiconductors, which were evidenced by electrochemical impedance spectroscopy (EIS) and photocurrent analysis.

Enhanced photocatalytic activity of anatase-TiO{sub 2} nanoparticles by fullerene modification: A theoretical and experimental study

Energy Technology Data Exchange (ETDEWEB)

Qi, Kezhen [Institute of Catalysis for Energy and Environment, College of Chemistry and Chemical Engineering, Shenyang Normal University, Shenyang, 110034 (China); Selvaraj, Rengaraj, E-mail: srengaraj1971@yahoo.com [Department of Chemistry, College of Science, Sultan Qaboos University, Muscat (Oman); Al Fahdi, Tharaya; Al-Kindy, Salma [Department of Chemistry, College of Science, Sultan Qaboos University, Muscat (Oman); Kim, Younghun [Department of Chemical Engineering, Kwangwoon University, Seoul 139-701 (Korea, Republic of); Wang, Gui-Chang [Department of Chemistry and the Tianjin Key Lab of Metal and Molecule-based Material Chemistry, Nankai University, Tianjin 300071 (China); Tai, Cheuk-Wai [Department of Materials and Environmental Chemistry, Arrhenius Laboratory, Stockholm University, S-106 91 Stockholm (Sweden); Sillanpää, Mika [Laboratory of Green Chemistry, LUT Savo Sustainable Technologies, Lappeenranta University of Technology, Sammonkatu 12, FI-50130 Mikkeli (Finland)

2016-11-30

Highlights: • C{sub 60}-modified a-TiO{sub 2} nanocomposites was successfully synthesized by a simple solvothermal method. • The C{sub 60}/a-TiO{sub 2} shows remarkably enhanced organic dyes degradation activity. • C{sub 60} modification enables a-TiO{sub 2} visible light absorption. • The photocatalytic mechanism has been proposed based on DFT calculation and experiments. - Abstract: A series of fullerene (C{sub 60})-modified anatase TiO{sub 2} (a-TiO{sub 2}) nanocomposites with different weight loadings of C{sub 60} were successfully synthesized by a simple solution phase method. The as-prepared C{sub 60}@a-TiO{sub 2} nanocomposites were characterized by X-ray diffraction (XRD), Raman spectroscopy, Brunauer-Emmett-Teller (BET), UV–vis diffuse reflectance absorption spectra (DRS), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and electron energy loss spectroscopy (EELS). The photocatalytic degradation of methylene blue (MB) by the neat a-TiO{sub 2} and C{sub 60}@a-TiO{sub 2} nanocomposites was investigated under UV-A light irradiation, demonstrating that C{sub 60} effectively enhances the photocatalytic activity of a-TiO{sub 2} nanoparticles with an optimal amount of 2.0 wt%. By combining with the density functional theory (DFT) calculations, we investigated the electronic structures of C{sub 60}@a-TiO{sub 2} hetero-interfaces to reveal the underlying principle of the C{sub 60} loading on the photocatalytic activity. It was found that the incorporation of C{sub 60} on the a-TiO{sub 2} surface not only narrowed the band gap, but also introduced an additional doping state between the valance and conduction band. Therefore, the presence of intermediate electronic state will in turn contribute to the efficient charge separation and enhanced light adsorption for the C{sub 60}@a-TiO{sub 2} nanocomposites, resulting in an improved photocatalytic performance.

Hydrogenated TiO2 nanotube photonic crystals for enhanced photoelectrochemical water splitting.

Science.gov (United States)

Meng, Ming; Zhou, Sihua; Yang, Lun; Gan, Zhixing; Liu, Kuili; Tian, Fengshou; Zhu, Yu; Li, ChunYang; Liu, Weifeng; Yuan, Honglei; Zhang, Yan

2018-04-02

We report the design, fabrication and characterization of novel TiO 2 nanotube photonic crystals with a crystalline core/disordered shell structure as well as substantial oxygen vacancies for photoelectrochemical (PEC) water splitting. The novel TiO 2 nanotube photonic crystals are fabricated by annealing of anodized TiO 2 nanotube photonic crystals in hydrogen atmosphere at various temperatures. The optimized novel TiO 2 nanotube photonic crystals produce a maximal photocurrent density of 2.2 mA cm -2 at 0.22 V versus Ag/AgCl, which is two times higher that of the TiO 2 nanotube photonic crystals annealed in air. Such significant PEC performance improvement can be ascribed to synergistic effects of the disordered surface layer and oxygen vacancies. The reduced band gap owing to the disordered surface layer and localized states induced by oxygen vacancies can enhance the efficient utilization of visible light. In addition, the disordered surface layer and substantial oxygen vacancies can promote the efficiency for separation and transport of the photogenerated carriers. This work may open up new opportunities for the design and construction of the high efficient and low-cost PEC water splitting system.

Enhanced gas sensing performance of TiO2 functionalized magneto-optical SPR sensors

OpenAIRE

Manera, Maria Grazia; Montagna, G.; Ferreiro-Vila, Elías; González-García, Lola; Sánchez-Valencia, J.R.; González-Elipe, Agustín R.; Cebollada, Alfonso; García-Martín, José Miguel; García-Martín, Antonio; Armelles Reig, Gaspar; Rella, Roberto

2011-01-01

Porous TiO2 thin films deposited by glancing angle deposition are used as sensing layers to monitor their sensing capabilities towards Volatile Organic Compounds both in a standard Surface Plasmon Resonance (SPR) sensor and in Magneto-Optical Surface Plasmon Resonance (MO-SPR) configuration in order to compare their sensing performances. Here our results on the enhanced sensing capability of these TiO2 functionalized MO-SPR sensors with Au/Co/Au transducers with respect to traditional SPR gas...

Fabrication of TiO2-modified polytetrafluoroethylene ultrafiltration membranes via plasma-enhanced surface graft pretreatment

Science.gov (United States)

Qian, Yingjia; Chi, Lina; Zhou, Weili; Yu, Zhenjiang; Zhang, Zhongzhi; Zhang, Zhenjia; Jiang, Zheng

2016-01-01

Surface hydrophilic modification of polymer ultrafiltration membrane using metal oxide represents an effective yet highly challenging solution to improve water flux and antifouling performance. Via plasma-enhanced graft of poly acryl acid (PAA) prior to coating TiO2, we successfully fixed TiO2 functional thin layer on super hydrophobic polytetrafluoroethylene (PTFE) ultrafiltration (UF) membranes. The characterization results evidenced TiO2 attached on the PTFE-based UF membranes through the chelating bidentate coordination between surface-grafted carboxyl group and Ti4+. The TiO2 surface modification may greatly reduce the water contact angle from 115.8° of the PTFE membrane to 35.0° without degradation in 30-day continuous filtration operations. The novel TiO2/PAA/PTFE membranes also exhibited excellent antifouling and self-cleaning performance due to the intrinsic hydrophilicity and photocatalysis properties of TiO2, which was further confirmed by the photo-degradation of MB under Xe lamp irradiation.

Enhanced solid-phase photocatalytic degradation of polyethylene by TiO{sub 2}–MWCNTs nanocomposites

Energy Technology Data Exchange (ETDEWEB)

An, Yang [School of Chemistry and Chemical Engineering/Key Laboratory for Green Processing of Chemical Engineering of Xinjiang Bingtuan, Shihezi University, Xinjiang 832003 (China); Hou, Juan [College of Sciences, Shihezi University, Xinjiang 832003 (China); Liu, Zhiyong [School of Chemistry and Chemical Engineering/Key Laboratory for Green Processing of Chemical Engineering of Xinjiang Bingtuan, Shihezi University, Xinjiang 832003 (China); Peng, Banghua, E-mail: banghuapeng@hotmail.com [School of Chemistry and Chemical Engineering/Key Laboratory for Green Processing of Chemical Engineering of Xinjiang Bingtuan, Shihezi University, Xinjiang 832003 (China)

2014-11-14

In this work, a novel acid vapor method was introduced to prepare the water soluble multi-walled carbon nanotubes (MWCNTs) and the titanium dioxide (TiO{sub 2})–MWCNTs nanocomposites photocatalyst were successfully synthesized by sol–gel solvothermal method. Products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD), which revealed that the anatase TiO{sub 2} particles were uniform deposited on MWCNTs surface. UV–vis diffuse reflectance spectroscopy (UV–vis) showed that composite photocatalyst had an obviously absorption band which covered the whole range of UV–vis region and exhibited a significant enhancement of optical absorption property. Based on above properties, we used the TiO{sub 2}–MWCNTs composites as photocatalysts to degrade the polyethylene (PE) plastic. Solid-phase PE film photocatalytic degradation experiments were investigated through monitoring TiO{sub 2}–MWCNTs–PE composite film's weight loss under mercury lamp irradiation. Results showed that the degradation efficiency could be tuned by changing the concentration of MWCNTs in photocatalyst. The photo-induced degradation of composite film was significantly higher than that of the pure PE film and the Degussa P25-PE film under the same UV irradiation. The weight loss of TiO{sub 2}–MWCNTs (20 wt%)–PE sample reached 35% under 180 h UV-light irradiation. Our work could be extended to synthesize other MWCNTs based composite with the purpose of enhancing TiO{sub 2}'s activity and inspiring for the practical environmental pollution, especially for degradation of plastics. - Highlights: • A novel acid vapor method was used to functionalize the MWCNTs. • Anatase nano-particles of TiO{sub 2} were uniform deposited on MWCNTs surface. • The composite photo-catalyst’s visible-light absorption capability was improved. • Polyethylene film's photodegradation efficiency was obviously enhanced

Self-assembled Bi{sub 2}MoO{sub 6}/TiO{sub 2} nanofiber heterojunction film with enhanced photocatalytic activities

Energy Technology Data Exchange (ETDEWEB)

Li, Hua [School of Chemical Engineering, Northwest University, Xi’an 710069 (China); Zhang, Tianxi [School of Physics, Northwest University, Xi’an 710069 (China); Pan, Chao; Pu, Chenchen; Hu, Yang [School of Chemical Engineering, Northwest University, Xi’an 710069 (China); Hu, Xiaoyun [School of Physics, Northwest University, Xi’an 710069 (China); Liu, Enzhou, E-mail: liuenzhou@nwu.edu.cn [School of Chemical Engineering, Northwest University, Xi’an 710069 (China); Fan, Jun, E-mail: fanjun@nwu.edu.cn [School of Chemical Engineering, Northwest University, Xi’an 710069 (China)

2017-01-01

Highlights: • Self-assembled Bi{sub 2}MoO{sub 6}/TiO{sub 2} nanofiber film was synthesized. • TiO{sub 2} nanofiber film exhibits excellent visible light scattering property. • The scattering light from TiO{sub 2} overlaps with the absorption light of Bi{sub 2}MoO{sub 6}. • Bi{sub 2}MoO{sub 6}/TiO{sub 2} heterojunction photocatalysts show higher photocatalytic activity. - Abstract: TiO{sub 2} nanofiber film (TiO{sub 2} NFF) was successfully fabricated by an ethylene glycol-assisted hydrothermal method, and then self-assembled flake-like Bi{sub 2}MoO{sub 6} was grown on the surface of TiO{sub 2} nanofiber under alcohol thermal condition. The investigations indicate that the nanofiber structure of TiO{sub 2} films exhibits excellent visible light scattering property, the scattering light overlaps with the absorption band of Bi{sub 2}MoO{sub 6}, which can enhance the utility of incident light. The prepared Bi{sub 2}MoO{sub 6}/TiO{sub 2} composites show obviously enhanced photocatalytic activity for methylene blue (MB) degradation compared with pure TiO{sub 2} nanofiber under visible light irradiation (λ > 420 nm). The enhanced photocatalytic activity is primarily attributed to the synergistic effect of visible light absorption and effective electron-hole separation at the interfaces of the two semiconductors, which is confirmed by photoluminescence (PL) and electrochemical tests.

Enhanced Photocatalytic Activity of TiO2 Nanoparticles Supported on Electrically Polarized Hydroxyapatite.

Science.gov (United States)

Zhang, Xuefei; Yates, Matthew Z

2018-05-23

Fast recombination of photogenerated charge carriers in titanium dioxide (TiO 2 ) remains a challenging issue, limiting the photocatalytic activity. This study demonstrates increased photocatalytic performance of TiO 2 nanoparticles supported on electrically polarized hydroxyapatite (HA) films. Dense and thermally stable yttrium and fluorine co-doped HA films with giant internal polarization were synthesized as photocatalyst supports. TiO 2 nanoparticles deposited on the support were then used to catalyze the photochemical reduction of aqueous silver ions to produce silver nanoparticles. It was found that significantly more silver nanoparticles were produced on polarized HA supports than on depolarized HA supports. In addition, the photodegradation of methyl orange with TiO 2 nanoparticles on polarized HA supports was found to be much faster than with TiO 2 nanoparticles on depolarized HA supports. It is proposed that separation of photogenerated electrons and holes in TiO nanoparticles is promoted by the internal polarization of the HA support, and consequently, the recombination of charge carriers is mitigated. The results imply that materials with large internal polarization can be used in strategies for enhancing quantum efficiency of photocatalysts.

Enhanced upper critical fields in binary Nb-Ti alloys

International Nuclear Information System (INIS)

Hariharan, Y.; Sastry, V.S.; Janawadkar, M.P.; Radhakrishnan, T.S.

1986-01-01

The authors report the enhancement of H/sub c2/ in quenched and suitably heat treated binary Nb-65 at % Ti alloys. The inherent metastability of the bcc β phase and its instability towards athermal ω are used to realise high values of normal state resistivity ε/sub n/. The consequences of this on the upper critical field have been experimentally determined by the measurement of dH/sub c2//dT at T/sub c/ and of T/sub c/. These together with our similar measurements on Nb-83 at % Ti alloy to which at 1 at % N was added (to retain it in the β phase) are analysed in terms of the existing theories for upper critical fields. It is shown that a peak in H/sub c2/(o) occurs at 17 - 18 T when ε/sub n/ has a value of approximately 100 μΩcm

Facile preparation of squarylium dye sensitized TiO{sub 2} nanoparticles and their enhanced visible-light photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Li, Zhongyu, E-mail: zhongyuli@mail.tsinghua.edu.cn [Jiangsu Key Laboratory of Advanced Catalytic Materials and Technology, School of Petrochemical Engineering, Changzhou University, Changzhou 213164 (China); Changzhou Expansion New Stuff Technology Limited Company, Changzhou 213122 (China); Fang, Yongling [Jiangsu Key Laboratory of Advanced Catalytic Materials and Technology, School of Petrochemical Engineering, Changzhou University, Changzhou 213164 (China); Zhan, Xueqiu [Department of Basic Courses, Wuxi Institute of Technology, Wuxi 214121 (China); Xu, Song [Jiangsu Key Laboratory of Advanced Catalytic Materials and Technology, School of Petrochemical Engineering, Changzhou University, Changzhou 213164 (China)

2013-07-05

Highlights: •ISQ dye sensitized TiO{sub 2} nanoparticles were prepared via a facile solution method. •ISQ/TiO{sub 2} nanoparticles exhibited significantly enhanced visible light activity. •ISQ/TiO{sub 2} showed high visible light photocatalytic activity over MB decomposition. •ISQ/TiO{sub 2} nanoparticles exhibited good photocatalytic stability. -- Abstract: A squarylium dye, 1,3-bis[(3,3-dimethylindolin-2-ylidene)methyl]squaraine (ISQ) sensitized TiO{sub 2} nanoparticles photocatalysts with different mass ratio of ISQ to TiO{sub 2} were facilely prepared by blending ISQ and TiO{sub 2} in ethanol solution. The resulting composite photocatalysts were characterized by the X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectra (FT-IR) and UV–vis diffuse reflectance spectroscope (DRS). The visible light photocatalytic activities of ISQ sensitized TiO{sub 2} nanoparticles were evaluated using the degradation of methylene blue (MB) as a photodegradation target. The results showed that photo-response of the ISQ sensitized TiO{sub 2} nanoparticles were remarkably extended to visible-light region, and the ISQ dye sensitized TiO{sub 2} exhibited significantly enhanced photocatalytic activity under visible light irradiation. The maximum photocatalytic activity of the ISQ sensitized TiO{sub 2} was found at a composite photocatalyst (mass ratio of ISQ to TiO{sub 2} was 1:3), and its degradation efficiency of MB reached approximately 98% in 2 h under visible light irradiation. Furthermore, a possible mechanism for the photocatalytic oxidative degradation was also proposed.

Deposition Rate and Energy Enhancements of TiN Thin-Film in a Magnetized Sheet Plasma Source

OpenAIRE

Hamdi Muhyuddin D. Barra; Henry J. Ramos

2011-01-01

Titanium nitride (TiN) has been synthesized using the sheet plasma negative ion source (SPNIS). The parameters used for its effective synthesis has been determined from previous experiments and studies. In this study, further enhancement of the deposition rate of TiN synthesis and advancement of the SPNIS operation is presented. This is primarily achieved by the addition of Sm-Co permanent magnets and a modification of the configuration in the TiN deposition process. The ...

Major enhancement of the thermoelectric performance in Pr/Nb-doped SrTiO3 under strain

KAUST Repository

Amin, B.; Alshareef, Husam N.; Schwingenschlö gl, Udo; Singh, Nirpendra; Tritt, T. M.

2013-01-01

site generate n-type doping and thus improve the thermoelectric performance as compared to pristine SrTiO3. Further enhancement is achieved by the application of strain, for example, of the Seebeck coefficient by 21% for Sr0.95Pr0.05TiO3 and 10% for Sr

Controllable hydrothermal synthesis of rutile TiO{sub 2} hollow nanorod arrays on TiCl{sub 4} pretreated Ti foil for DSSC application

Energy Technology Data Exchange (ETDEWEB)

Xi, Min [Key Laboratory of Renewable Energy, Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510640 (China); Zhang, Yulan; Long, Lizhen [Key Laboratory of Renewable Energy, Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510640 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Li, Xinjun, E-mail: lixj@ms.giec.ac.cn [Key Laboratory of Renewable Energy, Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510640 (China)

2014-11-15

Rutile TiO{sub 2} nanorod arrays (TNRs) were achieved by hydrothermal process on TiCl{sub 4} pretreated Ti foil. Subsequently, TNRs were hydrothermally etched in HCl solution to form hollow TiO{sub 2} nanorod arrays (H-TNRs). The TiCl{sub 4} pretreatment plays key roles in enhancement of Ti foil corrosion resistance ability and crystal nucleation introduction for TNRs growth. TNRs with desired morphology can be obtained by controlling TiCl{sub 4} concentration and the amount of tetrabutyl titanate (TTB) accordingly. TNRs with the length of ∼1.5 μm and diameter of ∼200 nm, obtained on 0.15 M TiCl{sub 4} pretreated Ti foil with 0.6 mL TTB, exhibits relatively higher photocurrent. The increased pore volume of the H-TNRs has contributed to the increased surface area which is benefit for Dye-Sensitized Solar Cells (DSSC) application. And the 180 °C-H-TNRs photoanode obtained from the 0.15-TiCl{sub 4}-TNRs sample demonstrated 128.9% enhancement of photoelectric efficiency of DSSC compared to that of the original TNR photoanode. - Graphical abstract: Rutile hollow TiO{sub 2} nanorod array photoanode obtained from original TiO{sub 2} nanorod array photoanode by hydrothermal etching demonstrates enhanced photoelectric efficiency of DSSC. - Highlights: • TiO{sub 2} nanorods are prepared via hydrothermal process on TiCl{sub 4}-pretreated Ti foil. • Hollow TiO{sub 2} nanorods are obtained by hydrothermal etching of TiO{sub 2} nanorods. • TiCl{sub 4} pretreatment plays a key role in protecting Ti foil from chemical corrosion. • Hollow TiO{sub 2} nanorods photoanode shows enhanced photoelectric efficiency for DSSC.

Microstructural and Material Quality Effects on Rolling Contact Fatigue of Highly Elastic Intermetallic NiTi Ball Bearings

Science.gov (United States)

Dellacorte, Christopher; Howard, S. Adam; Thomas, Fransua; Stanford, Malcolm K.

2017-01-01

Rolling element bearings made from highly-elastic intermetallic materials (HIM)s, such as 60NiTi, are under development for applications that require superior corrosion and shock resistance. Compared to steel, intermetallics have been shown to have much lower rolling contact fatigue (RCF) stress capability in simplified 3-ball on rod (ASTM STP 771) fatigue tests. In the 3-ball tests, poor material quality and microstructural flaws negatively affect fatigue life but such relationships have not been established for full-scale 60NiTi bearings. In this paper, 3-ball-on-rod fatigue behavior of two quality grades of 60NiTi are compared to the fatigue life of full-scale 50mm bore ball bearings made from the same materials. 60NiTi RCF rods with material or microstructural flaws suffered from infant mortality failures at all tested stress levels while high quality 60NiTi rods exhibited no failures at lower stress levels. Similarly, tests of full-scale bearings made from flawed materials exhibited early surface fatigue and through crack type failures while bearings made from high quality material did not fail even in long-term tests. Though the full-scale bearing test data is yet preliminary, the results suggest that the simplified RCF test is a good qualitative predictor of bearing performance. These results provide guidance for materials development and to establish minimum quality levels required for successful bearing operation and life.

Enhanced photovoltaic properties of perovskite solar cells by TiO2 homogeneous hybrid structure.

Science.gov (United States)

Su, Pengyu; Fu, Wuyou; Yao, Huizhen; Liu, Li; Ding, Dong; Feng, Fei; Feng, Shuang; Xue, Yebin; Liu, Xizhe; Yang, Haibin

2017-10-01

In this paper, we fabricated a TiO 2 homogeneous hybrid structure for application in perovskite solar cells (PSCs) under ambient conditions. Under the standard air mass 1.5 global (AM 1.5G) illumination, PSCs based on homogeneous hybrid structure present a maximum power conversion efficiency of 5.39% which is higher than that of pure TiO 2 nanosheets. The enhanced properties can be explained by the better contact of TiO 2 nanosheets/nanoparticles with CH 3 NH 3 PbI 3 and fewer pinholes in electron transport materials. The advent of such unique structure opens up new avenues for the future development of high-efficiency photovoltaic cells.

Major enhancement of the thermoelectric performance in Pr/Nb-doped SrTiO3 under strain

KAUST Repository

Amin, B.

2013-07-16

The electronic structure and thermoelectric properties of strained (biaxially and uniaxially) Sr0.95Pr0.05TiO3 and SrTi0.95Nb0.05O3 are investigated in the temperature range from 300 K to 1200 K. Substitutions of Pr at the Sr site and Nb at the Ti site generate n-type doping and thus improve the thermoelectric performance as compared to pristine SrTiO3. Further enhancement is achieved by the application of strain, for example, of the Seebeck coefficient by 21% for Sr0.95Pr0.05TiO3 and 10% for SrTi0.95Nb0.05O3 at room temperature in the case of 5% biaxial strain. At 1200 K, we predict figures of merit of 0.58 and 0.55 for 2.5% biaxially strained Sr0.95Pr0.05TiO3 and SrTi0.95Nb0.05O3 , respectively, which are the highest values reported for rare earth doped SrTiO3.

Plasma-induced synthesis of Pt nanoparticles supported on TiO{sub 2} nanotubes for enhanced methanol electro-oxidation

Energy Technology Data Exchange (ETDEWEB)

Su, Nan [College of Materials Science and Engineering, Nanjing Tech University, Xin-Mo-Fan Road No. 5, 210009, Nanjing, Jiangsu (China); The Synergetic Innovation Center for Advanced Materials, Xin-Mo-Fan Road No. 5, 210009, Nanjing, Jiangsu (China); Jiangsu National Synergetic Innovation Center for Advanced Materials (SICAM), Xin-Mo-Fan Road No. 5, 210009, Nanjing, Jiangsu (China); Hu, Xiulan, E-mail: whoxiulan@163.com [College of Materials Science and Engineering, Nanjing Tech University, Xin-Mo-Fan Road No. 5, 210009, Nanjing, Jiangsu (China); The Synergetic Innovation Center for Advanced Materials, Xin-Mo-Fan Road No. 5, 210009, Nanjing, Jiangsu (China); Jiangsu National Synergetic Innovation Center for Advanced Materials (SICAM), Xin-Mo-Fan Road No. 5, 210009, Nanjing, Jiangsu (China); Zhang, Jianbo; Huang, Huihong; Cheng, Jiexu; Yu, Jinchen; Ge, Chao [College of Materials Science and Engineering, Nanjing Tech University, Xin-Mo-Fan Road No. 5, 210009, Nanjing, Jiangsu (China)

2017-03-31

Highlights: • Pt nanoparticles are synthesized by plasma sputtering in water. • Pt/C/TiO{sub 2} nanotubes shows better mass activity and CO-poisoning tolerance than Pt/C. • TiO{sub 2} nanotubes are more suitable for support materials than TiO{sub 2} small particles. • The metal-support interactions between Pt and TiO{sub 2} nanotubes are detected by XPS. - Abstract: A Pt/C/TiO{sub 2} nanotube composite catalyst was successfully prepared for enhanced methanol electro-oxidation. Pt nanoparticles with a particle size of 2 nm were synthesized by plasma sputtering in water, and anatase TiO{sub 2} nanotubes with an inner diameter of approximately 100 nm were prepared by a simple two-step anodization method and annealing process. Field-emission scanning electron microscopy images indicated that the different morphologies of TiO{sub 2} synthesized on the surface of Ti foils were dependent on the different anodization parameters. The electrochemical performance of Pt/C/TiO{sub 2} catalysts for methanol oxidation showed that TiO{sub 2} nanotubes were more suitable for use as Pt nanoparticle support materials than irregular TiO{sub 2} short nanorods due to their tubular morphology and better electronic conductivity. X-ray photoelectron spectroscopy characterization showed that the binding energies of the Pt 4f of the Pt/C/TiO{sub 2} nanotubes exhibited a slightly positive shift caused by the relatively strong interaction between Pt and the TiO{sub 2} nanotubes, which could mitigate the poisoning of the Pt catalyst by CO{sub ads}, and further enhance the electrocatalytic performance. Thus, the as-obtained Pt/C/TiO{sub 2} nanotubes composites may become a promising catalyst for methanol electro-oxidation.

Photovoltaic performance enhancement of CdS quantum dot-sensitized TiO{sub 2} photoanodes with plasmonic gold nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Liu, Aiping, E-mail: liuaiping1979@gmail.com [Center for Optoelectronics Materials and Devices, Zhejiang Sci-Tech University, Hangzhou 310018 (China); State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Ren, Qinghua; Zhao, Ming; Xu, Tao; Yuan, Ming; Zhao, Tingyu [Center for Optoelectronics Materials and Devices, Zhejiang Sci-Tech University, Hangzhou 310018 (China); Tang, Weihua [State Key Laboratory of Information Photonics and Optical Communication, Beijing University Posts and Telecommunications, Beijing 100876 (China)

2014-03-15

Highlights: • CdS QD-sensitized TiO{sub 2} porous photoanode with plasmonic gold. • A prominent light absorption enhancement of hybrid was attained by gold plasmon. • The photovoltaic response of hybrid was tunable by CdS amount. • The Au/TiO{sub 2}/CdS hybrid had a potential application in energy conversion devices. -- Abstract: The CdS quantum dot-sensitized TiO{sub 2} films with plasmonic gold nanoparticles were designed as photoanodes by the electrodeposition of gold combined with the “successive ionic layer adsorption and reaction” (SILAR) method for CdS deposition on porous TiO{sub 2} films. A prominent enhancement in light absorption of Au/TiO{sub 2}/CdS hybrid was attained by efficient light scattering of gold plasmons as sub-wavelength antennas and concentrators. The photogenerated electron formed in the near-surface region of TiO{sub 2} and CdS were facilitated to transfer to the plasmonic gold, resulting in the enhancement of photocurrent and incident photon-to-current conversion efficiency of hybrid photoanode upon photoirradiation. Furthermore, the photovoltaic response of hybrid was highly tunable with respect to the number of SILAR cycles applied to deposit CdS. The thicker absorber layer with less porous structure and larger CdS crystals might limit the electrolyte diffusion into the hybrid electrode and impose a barrier for electron tunneling and transferring. The highly versatile and tunable properties of Au/TiO{sub 2}/CdS photoanodes demonstrated their potential application in energy conversion devices.

On the development of high quality NiTi shape memory and pseudoelastic parts by additive manufacturing

International Nuclear Information System (INIS)

Haberland, Christoph; Elahinia, Mohammad; Walker, Jason M; Meier, Horst; Frenzel, Jan

2014-01-01

Additive manufacturing provides an attractive processing method for nickel–titanium (NiTi) shape memory and pseudoelastic parts. In this paper, we show how the additive manufacturing process affects structural and functional properties of additively manufactured NiTi and how the process parameter set-up can be optimized to produce high quality NiTi parts and components. Comparisons of shape recovery due to shape memory and pseudoelasticity in additively manufactured and commercial NiTi exhibit promising potential for this innovative processing method. (paper)

Fabrication, structure, and enhanced photocatalytic properties of hierarchical CeO2 nanostructures/TiO2 nanofibers heterostructures

International Nuclear Information System (INIS)

Cao, Tieping; Li, Yuejun; Wang, Changhua; Wei, Liming; Shao, Changlu; Liu, Yichun

2010-01-01

Combining the versatility of electrospinning technique and hydrothermal growth of nanostructures enabled the fabrication of hierarchical CeO 2 /TiO 2 nanofibrous mat. The as-prepared hierarchical heterostructure consisted of CeO 2 nanostructures growing on the primary TiO 2 nanofibers. Interestingly, not only were secondary CeO 2 nanostructures successfully grown on TiO 2 nanofibers substrates, but also the CeO 2 nanostructures were uniformly distributed without aggregation on TiO 2 nanofibers. By selecting different alkaline source, CeO 2 /TiO 2 heterostructures with CeO 2 nanowalls or nanoparticles were facilely fabricated. The photocatalytic studies suggested that the CeO 2 /TiO 2 heterostructures showed enhanced photocatalytic efficiency of photodegradation of dye pollutants compared with bare TiO 2 nanofibers under UV light irradiation.

Enhancement of the photocatalytic activity of TiO2 nanoparticles by surface-capping DBS groups

International Nuclear Information System (INIS)

Wang Baiqi; Jing Liqiang; Qu Yichun; Li Shudan; Jiang Baojiang; Yang Libin; Xin Baifu; Fu Honggang

2006-01-01

TiO 2 nanoparticles capped with sodium dodecylbenzenesulfonate (DBS) are synthesized by a sol-hydrothermal process using tetrabutyl titanate and DBS as raw materials. The effects of surface-capping DBS on the surface photovoltage spectroscopy (SPS), photoluminescence (PL) and photocatalytic performance of TiO 2 nanoparticles are principally investigated together with their relationships. The results show that the surface of TiO 2 nanoparticles can be well capped by DBS groups while the pH value and added DBS amount are controlled at 5.0 and 2% of TiO 2 mass weight, respectively, and the linkage between DBS groups and TiO 2 surfaces is mainly by means of quasi-sulphonate bond. The intensities of SPS and PL spectra of TiO 2 obviously decrease after DBS-capping, while the activity can greatly increase during the photocatalytic degradation of Rhodamine B (RhB) solution, which are mainly attributed to the electron-withdrawing character of the DBS groups. Moreover, the enhancement of photocatalytic activity of DBS-capped TiO 2 is also related to the increase in the capability for adsorbing RhB

The Concepts of Quality, Quality Assurance and Quality Enhancement

Science.gov (United States)

Elassy, Noha

2015-01-01

Purpose: This paper aims to critically review and discuss different definitions of the concepts of quality, quality assurance (QA) and quality enhancement (QE) in higher education (HE) with presenting critical perspectives of the literature. Design/methodology/approach: The paper looks at literature concerns with the meaning of quality, QA and QE,…

Controlled Synthesis of CuS/TiO2 Heterostructured Nanocomposites for Enhanced Photocatalytic Hydrogen Generation through Water Splitting.

Science.gov (United States)

Chandra, Moumita; Bhunia, Kousik; Pradhan, Debabrata

2018-04-16

Photocatalytic hydrogen (H 2 ) generation through water splitting has attracted substantial attention as a clean and renewable energy generation process that has enormous potential in converting solar-to-chemical energy using suitable photocatalysts. The major bottleneck in the development of semiconductor-based photocatalysts lies in poor light absorption and fast recombination of photogenerated electron-hole pairs. Herein we report the synthesis of CuS/TiO 2 heterostructured nanocomposites with varied TiO 2 contents via simple hydrothermal and solution-based process. The morphology, crystal structure, composition, and optical properties of the as-synthesized CuS/TiO 2 hybrids are evaluated in detail. Controlling the CuS/TiO 2 ratio to an optimum value leads to the highest photocatalytic H 2 production rate of 1262 μmol h -1 g -1 , which is 9.7 and 9.3 times higher than that of pristine TiO 2 nanospindles and CuS nanoflakes under irradiation, respectively. The enhancement in the H 2 evolution rate is attributed to increased light absorption and efficient charge separation with an optimum CuS coverage on TiO 2 . The photoluminescence and photoelectrochemical measurements further confirm the efficient separation of charge carriers in the CuS/TiO 2 hybrid. The mechanism and synergistic role of CuS and TiO 2 semiconductors for enhanced photoactivity is further delineated.

Thermoelectric performance enhancement of SrTiO3 by Pr doping

KAUST Repository

Kahaly, M. Upadhyay; Schwingenschlö gl, Udo

2014-01-01

We investigate Pr doping at the Sr site as a possible route to enhance the thermoelectric behavior of SrTiO3-based materials, using first principles calculations in full-potential density functional theory. The effects of the Pr dopant on the local electronic structure and resulting transport properties are compared to common Nb doping. We demonstrate a substantial enhancement of the thermoelectric figure of merit and develop an explanation for the positive effects, which opens new ways for materials optimization by substitutional doping at the perovskite B site. © 2014 the Partner Organisations.

Facile synthesis and characterization of N-doped TiO2/C nanocomposites with enhanced visible-light photocatalytic performance

Science.gov (United States)

Jia, Tiekun; Fu, Fang; Yu, Dongsheng; Cao, Jianliang; Sun, Guang

2018-02-01

Ultrafine anatase N-doped TiO2 nanocrystals modified with carbon (denoted as N-doped TiO2/C) were successfully prepared via a facile and low-cost approach, using titanium tetrachloride, aqueous ammonia and urea as starting materials. The phase composition, surface chemical composition, morphological structure, electronic and optical properties of the as-prepared photocatalysts were well characterized and analyzed. On the basis of Raman spectral characterization combining with the results of X-ray photoelectron spectroscopy (XPS) and high resolution transmission electron microscopy (HRTEM), it could be concluded that N dopant ions were successfully introduced into TiO2 crystal lattice and carbon species were modified on the surface or between the nanoparticles to form N-doped TiO2/C nanocomposites. Compared with that of bare TiO2, the adsorption band edge of N-doped TiO2/C nanocomposites were found to have an evident red-shift toward visible light region, implying that the bandgap of N-doped TiO2/C nanocomposites is narrowed and the visible light absorption capacity is significantly enhanced due to N doping and carbon modification. The photoactivity of the as-prepared photocatalytsts was tested by the degradation of Rhodamine B (RhB) under visible light (λ > 420 nm), and the results showed that the N-doped TiO2/C nanocomposites exhibited much higher photodegradation rate than pure TiO2 and N-doped TiO2, which was mainly attributed to the synergistic effect of the enhanced light harvesting, augmented catalytic active sites and efficient separation of photogenerated electron-hole pairs.

Enhanced interfacial contact between PbS and TiO2 layers in quantum dot solar cells using 2D-arrayed TiO2 hemisphere nanostructures

Science.gov (United States)

Lee, Wonseok; Ryu, Ilhwan; Lee, Haein; Yim, Sanggyu

2018-02-01

Two-dimensionally (2D) arrayed hemispherical nanostructures of TiO2 thin films were successfully fabricated using a simple procedure of spin-coating or dip-coating TiO2 nanoparticles onto 2D close-packed polystyrene (PS) nanospheres, followed by PS extraction. The nanostructured TiO2 film was then used as an n-type layer in a lead sulfide (PbS) colloidal quantum dot solar cell. The TiO2 nanostructure could provide significantly increased contacts with subsequently deposited PbS quantum dot layer. In addition, the periodically arrayed nanostructure could enhance optical absorption of the cell by redirecting the path of the incident light and increasing the path length passing though the active layer. As a result, the power conversion efficiency (PCE) reached 5.13%, which is approximately a 1.7-fold increase over that of the control cell without nanostructuring, 3.02%. This PCE enhancement can mainly be attributed to the increase of the short-circuit current density from 19.6 mA/cm2 to 30.6 mA/cm2, whereas the open-circuit voltage and fill factor values did not vary significantly.

A metallic metal oxide (Ti5O9)-metal oxide (TiO2) nanocomposite as the heterojunction to enhance visible-light photocatalytic activity.

Science.gov (United States)

Li, L H; Deng, Z X; Xiao, J X; Yang, G W

2015-01-26

Coupling titanium dioxide (TiO2) with other semiconductors is a popular method to extend the optical response range of TiO2 and improve its photon quantum efficiency, as coupled semiconductors can increase the separation rate of photoinduced charge carriers in photocatalysts. Differing from normal semiconductors, metallic oxides have no energy gap separating occupied and unoccupied levels, but they can excite electrons between bands to create a high carrier mobility to facilitate kinetic charge separation. Here, we propose the first metallic metal oxide-metal oxide (Ti5O9-TiO2) nanocomposite as a heterojunction for enhancing the visible-light photocatalytic activity of TiO2 nanoparticles and we demonstrate that this hybridized TiO2-Ti5O9 nanostructure possesses an excellent visible-light photocatalytic performance in the process of photodegrading dyes. The TiO2-Ti5O9 nanocomposites are synthesized in one step using laser ablation in liquid under ambient conditions. The as-synthesized nanocomposites show strong visible-light absorption in the range of 300-800 nm and high visible-light photocatalytic activity in the oxidation of rhodamine B. They also exhibit excellent cycling stability in the photodegrading process. A working mechanism for the metallic metal oxide-metal oxide nanocomposite in the visible-light photocatalytic process is proposed based on first-principle calculations of Ti5O9. This study suggests that metallic metal oxides can be regarded as partners for metal oxide photocatalysts in the construction of heterojunctions to improve photocatalytic activity.

Hydrothermal synthesis and photoelectrochemical performance enhancement of TiO{sub 2}/graphene composite in photo-generated cathodic protection

Energy Technology Data Exchange (ETDEWEB)

Zhang, Weiwei, E-mail: vivizhg@yahoo.com [College of Material Science and Engineering, Shandong University of Science and Technology, Qingdao 266590 (China); State Key Laboratory of Mining Disaster Prevention and Control Co-founded by Shandong Province and the Ministry of Science and Technology, Shandong University of Science and Technology, Qingdao 266590 (China); Guo, Hanlin; Sun, Haiqing [College of Material Science and Engineering, Shandong University of Science and Technology, Qingdao 266590 (China); Zeng, Rong-Chang [College of Material Science and Engineering, Shandong University of Science and Technology, Qingdao 266590 (China); State Key Laboratory of Mining Disaster Prevention and Control Co-founded by Shandong Province and the Ministry of Science and Technology, Shandong University of Science and Technology, Qingdao 266590 (China)

2016-09-30

Highlights: • TiO{sub 2}/graphene composites were synthesized through one-step hydrothermal method. • A bicrystalline framework of anatase and brookite formed. • Electrons transfer in the biphasic TiO{sub 2} results in electron-hole separation. • Graphene lead to a negative shift of the Fermi level. • The transfer barrier in the TiO{sub 2} and 304 stainless steel interface is decreased. - Abstract: TiO{sub 2}/graphene composites were synthesized through one-step hydrothermal method. The composites show an enhancement in photo-generated cathodic protection as the time-dependent profiles of photocurrent responses has confirmed. XRD data show that a bicrystalline framework of anatase and brookite formed as graphene provided donor groups in the hydrothermal process. The transfer of photoinduced electrons in the biphasic TiO{sub 2} results in effective electron-hole separation. Moreover, graphene lead to a negative shift of the Fermi level as evidenced by Mott–Schottky analysis, which decreases the Schottky barrier formed in the TiO{sub 2} and 304 stainless steel interface and results in the enhancement of photo-generated cathodic protection.

The influence of shell thickness of Au@TiO2 core-shell nanoparticles on the plasmonic enhancement effect in dye-sensitized solar cells.

Science.gov (United States)

Liu, Wei-Liang; Lin, Fan-Cheng; Yang, Yu-Chen; Huang, Chen-Hsien; Gwo, Shangjr; Huang, Michael H; Huang, Jer-Shing

2013-09-07

Plasmonic core-shell nanoparticles (PCSNPs) can function as nanoantennas and improve the efficiency of dye-sensitized solar cells (DSSCs). To achieve maximum enhancement, the morphology of PCSNPs needs to be optimized. Here we precisely control the morphology of Au@TiO2 PCSNPs and systematically study its influence on the plasmonic enhancement effect. The enhancement mechanism was found to vary with the thickness of the TiO2 shell. PCSNPs with a thinner shell mainly enhance the current, whereas particles with a thicker shell improve the voltage. While pronounced plasmonic enhancement was found in the near infrared regime, wavelength-independent enhancement in the visible range was observed and attributed to the plasmonic heating effect. Emission lifetime measurement confirms that N719 molecules neighboring nanoparticles with TiO2 shells exhibit a longer lifetime than those in contact with metal cores. Overall, PCSNPs with a 5 nm shell give the highest efficiency enhancement of 23%. Our work provides a new synthesis route for well-controlled Au@TiO2 core-shell nanoparticles and gains insight into the plasmonic enhancement in DSSCs.

Highly Ordered Periodic Au/TiO₂ Hetero-Nanostructures for Plasmon-Induced Enhancement of the Activity and Stability for Ethanol Electro-oxidation.

Science.gov (United States)

Jin, Zhao; Wang, Qiyu; Zheng, Weitao; Cui, Xiaoqiang

2016-03-02

The catalytic electro-oxidation of ethanol is the essential technique for direct alcohol fuel cells (DAFCs) in the area of alternative energy for the ability of converting the chemical energy of alcohol into the electric energy directly. Developing highly efficient and stable electrode materials with antipoisoning ability for ethanol electro-oxidation remains a challenge. A highly ordered periodic Au-nanoparticle (NP)-decorated bilayer TiO2 nanotube (BTNT) heteronanostructure was fabricated by a two-step anodic oxidation of Ti foil and the subsequent photoreduction of HAuCl4. The plasmon-induced charge separation on the heterointerface of Au/TiO2 electrode enhances the electrocatalytic activity and stability for the ethanol oxidation under visible light irradiation. The highly ordered periodic heterostructure on the electrode surface enhanced the light harvesting and led to the greater performance of ethanol electro-oxidation under irradiation compared with the ordinary Au NPs-decorated monolayer TiO2 nanotube (MTNT). This novel Au/TiO2 electrode also performed a self-cleaning property under visible light attributed to the enhanced electro-oxidation of the adsorbed intermediates. This light-driven enhancement of the electrochemical performances provides a development strategy for the design and construction of DAFCs.

Enhanced visible-light activities for PEC water reduction of CuO nanoplates by coupling with anatase TiO2 and mechanism

International Nuclear Information System (INIS)

Li, Zhijun; Qu, Yang; He, Guangwen; Humayun, Muhammad; Chen, Shuangying; Jing, Liqiang

2015-01-01

Graphical abstract: - Highlights: • CuO nanoplates were successfully prepared as photocathodes for PEC water reduction. • Visible-light activity for PEC water reduction is improved after coupling with TiO 2 . • Improved PEC performance is attributed to the enhanced visible-excited charge separation. • Enhanced charge separation results from high-energy electron transfer from CuO to TiO 2 . - Abstract: CuO nanoplates were prepared by a feasible hydrothermal method, and then utilized as photocathodes for photoelectrochemical (PEC) water reduction in a neutral medium under visible-light irradiation. It is clearly demonstrated that the visible-light activities of the resulting nanoplates for PEC water reduction could be greatly improved after coupling with a proper amount of nanocrystalline anatase TiO 2 . This is attributed to the enhanced charge separation in the fabricated TiO 2 /CuO nanoplate composites mainly based on the atmosphere-controlled steady-state surface photovoltage spectra. Moreover, it is suggested that the enhanced charge separation resulted from the transfer of visible-light-excited high-energy electrons from CuO to TiO 2 as confirmed from the single-wavelength PEC behavior

Enhanced the hydrophobic surface and the photo-activity of TiO2-SiO2 composites

Science.gov (United States)

Wahyuni, S.; Prasetya, A. T.

2017-02-01

The aim of this research is to develop nanomaterials for coating applications. This research studied the effect of various TiO2-SiO2 composites in acrylic paint to enhance the hydrophobic properties of the substrate. Titanium dioxide containing silica in the range 20-35 mol% has been synthesized using sol-gel route. The XRD’s spectra show that increasing SiO2 content in the composite, decreasing its crystalline properties but increasing the surface area. TiO2-SiO2 composite was dispersed in acrylic paint in 2% composition by weight. The largest contact angle was 70, which produced by the substrate coated with TS-35-modified acrylic paint. This study also investigated the enhanced photo-activity of TiO2-SiO2 modified with poly-aniline. The XRD spectra show that the treatment does not change the crystal structure of TiO2. The photo-activity of the composite was evaluated by degradation of Rhodamine-B with visible light. The best performance of the degradation process was handled by the composite treated with 0.1mL anilines per gram of TiO2-SiO2 composite (TSP-A). On the other side, the contact angle 70 has not shown an excellent hydrophobic activity. However, the AFM spectra showed that nanoroughness has started to form on the surface of acrylic paint modified with TiO2-SiO2 than acrylic alone.

Hierarchical (0 0 1) facet anatase/rutile TiO2 heterojunction photoanode with enhanced photoelectrocatalytic performance

International Nuclear Information System (INIS)

Tian, Hongyi; Zhao, Guohua; Zhang, Ya-nan; Wang, Yanbin; Cao, Tongcheng

2013-01-01

Highlights: ► (0 0 1) facet TiO 2 photoanode with large surface area is reported for the first time. ► Ordered heterojunction further improves light absorption in (0 0 1) facet TiO 2 system. ► (0 0 1) facet TiO 2 photoanode possesses promoted photoelectrocatalytic performance. ► Photoelectrical enhancement mechanism is clarified by electrochemical methods. ► Photogenerated carrier and lifetime are remarkably enhanced by ingenious design. -- Abstract: A hierarchical heterojunction TiO 2 photoanode with large surface/body ratio is reported to exhibit high oxidation activity due to the constructing of anatase TiO 2 with exposed (0 0 1) facets. The mixed-phase photoanode is fabricated through surfactant-assisted anchoring ultrathin anatase nanosheets on vertically ordered rutile nanorod arrays. This cactaceae-like TiO 2 possesses high-exposed (0 0 1) facets outer layer, large specific surface area (375 m 2 g −1 ), efficient photo-to-current conversion (8.2%) and excellent photocatalytic ability to degrade bisphenol A. The greatly promoted photoelectric and photocatalytic performance results from the synergetic effects of the architecture design of high-active (0 0 1) facets and hierarchical heterojunctions. The mechanism analysis reveals that the remarkable increase of photogenerated carrier concentration (2.40 × 10 22 cm −3 ) improves photocatalytic activity, by virtue of constructing staggered energy levels, suppressing the recombination of electrons and holes, and extending the electron lifetime (133 ms)

Contributions of conduction band offset to the enhanced separation efficiency of photoinduced charges for SrTiO3/Bi2O3 heterojunction semiconductor

International Nuclear Information System (INIS)

Zhang, Zhenlong; Zhu, Jichun; Li, Shengjun; Mao, Yanli

2014-01-01

SrTiO 3 /Bi 2 O 3 heterojunction semiconductor was prepared and characterized by X-ray diffraction, UV–vis absorption spectrum, and scanning electron microscope, surface photovoltage spectroscopy, and photoluminescence spectroscopy. The surface photovoltage spectra indicate that the separation efficiency of photoinduced charges for SrTiO 3 /Bi 2 O 3 was enhanced compared with that of SrTiO 3 or Bi 2 O 3 . The energy band diagram of SrTiO 3 /Bi 2 O 3 heterojunction was directly determined with X-ray photoelectron spectroscopy, and the conduction band offset between SrTiO 3 and Bi 2 O 3 was quantified to be 0.28±0.03 eV. The photoluminescence spectra display that the recombination rate of photoinduced carriers for SrTiO 3 /Bi 2 O 3 decreases compared with that of SrTiO 3 or Bi 2 O 3 , which is mainly due to the energy levels matching between them. Therefore the enhanced separation efficiency of photoinduced charges is resulting from the energy difference between the conduction band edges of SrTiO 3 and Bi 2 O 3 . -- Graphical abstract: Enhanced separation efficiency for SrTiO 3 /Bi 2 O 3 is resulting from the energy difference between the conduction band edges. Highlights: ●Heterojunction semiconductor of SrTiO 3 /Bi 2 O 3 was prepared. ●SrTiO 3 /Bi 2 O 3 presents enhanced separation efficiency. ●Conduction band offset between SrTiO 3 and Bi 2 O 3 is quantified. ●Recombination rate of SrTiO 3 /Bi 2 O 3 decreases compared with single phases

Enhanced Sonocatalytic Degradation of Rhodamine B by Graphene-TiO2 Composites Synthesized by an Ultrasonic-Assisted Method%Enhanced Sonocatalytic Degradation of Rhodamine B by Graphene-TiO2 Composites Synthesized by an Ultrasonic-Assisted Method

Institute of Scientific and Technical Information of China (English)

ZHU Lei; Trisha GHOSH; Chong-Yeon PARK; MENG Ze-Da; OH Won-Chun

2012-01-01

A series of graphene-TiO2 composites was fabricated from graphene oxide and titanium n-butoxide (TNB) by an ultrasonic-assisted method.The structure and composition of the nanocomposites were characterized by Raman spectroscopy,BET surface area measurements,X-ray diffraction,transmission electron microscopy,and ultraviolet-visible absorption spectroscopy.The average size of the TiO2 nanoparticles on the graphene nanosheets was controlled at around 10-15 nm without using surfactant,which is attributed to the pyrolysis and condensation of dissolved TNB into TiO2 by ultrasonic irradiation.The catalytic activity of the composites under ultrasonic irradiation was determined using a rhodamine B (RhB) solution.The graphene-TiO2 composites possessed a high specific surface area,which increased the decolorization rate for RhB solution.This is because the graphene and TiO2 nanoparticles in the composites interact strongly,which enhances the photoelectric conversion of TiO2 by reducing the recombination ofphotogenerated electron-hole pairs.

Bi-functional TiO2 cemented Ag grid under layer for enhancing the photovoltaic performance of a large-area dye-sensitized solar cell

International Nuclear Information System (INIS)

Lan Zhang; Wu Jihuai; Lin Jianming; Huang, Miaoliang

2012-01-01

Graphical abstract: Enhanced photovoltaic performance of large-area DSSC with conductive grids in the photo and counter electrodes. Highlights: ► TiO 2 protected Ag grids is made for using as electrode in large-area DSSC. ► The electrode has high conductivity and low internal resistance. ► TiO 2 protected Ag grids electrode avoids iodine corrosion in electrolyte. ► The TiO 2 layer also play a blocking layer role. ► Above factors enhance the photovoltaic performance of large-area DSSC. - Abstract: A bi-functional TiO 2 cemented Ag grid under layer for enhanced the photovoltaic performance of a large-area dye-sensitized solar cell (DSSC) is prepared with a simple way. The conductive printing paste contains micro-sized Ag powders and nano-sized TiO 2 cementing agent. The conductive printing paste can be well cemented on the FTO glass and form high conductive grids with Ag powders sintered together by the nano-sized TiO 2 particles. The formed conductive grid is protected with a TiO 2 thin layer and TiO 2 sol treatment to avoid the iodine corrosion. The addition of the TiO 2 cemented conductive grid can decrease the internal resistance of the large-area dye-sensitized solar cell when it is prepared in the photo and counter electrodes. Furthermore, the protecting TiO 2 thin layer and the TiO 2 sol treatment can be done on the whole area of the large-area photo electrode to both play as the blocking under layer at the same time, which can also enhance the photovoltaic performance of the large-area dye-sensitized solar cell.

Decorating TiO2 Nanowires with BaTiO3 Nanoparticles: A New Approach Leading to Substantially Enhanced Energy Storage Capability of High-k Polymer Nanocomposites.

Science.gov (United States)

Kang, Da; Wang, Guanyao; Huang, Yanhui; Jiang, Pingkai; Huang, Xingyi

2018-01-31

The urgent demand of high energy density and high power density devices has triggered significant interest in high dielectric constant (high-k) flexible nanocomposites comprising dielectric polymer and high-k inorganic nanofiller. However, the large electrical mismatch between polymer and nanofiller usually leads to earlier electric failure of the nanocomposites, resulting in an undesirable decrease of electrical energy storage capability. A few studies show that the introduction of moderate-k shell onto a high-k nanofiller surface can decrease the dielectric constant mismatch, and thus, the corresponding nanocomposites can withstand high electric field. Unfortunately, the low apparent dielectric enhancement of the nanocomposites and high electrical conductivity mismatch between matrix and nanofiller still result in low energy density and low efficiency. In this study, it is demonstrated that encapsulating moderate-k nanofiller with high-k but low electrical conductivity shell is effective to significantly enhance the energy storage capability of dielectric polymer nanocomposites. Specifically, using BaTiO 3 nanoparticles encapsulated TiO 2 (BaTiO 3 @TiO 2 ) core-shell nanowires as filler, the corresponding poly(vinylidene fluoride-co-hexafluoropylene) nanocomposites exhibit superior energy storage capability in comparison with the nanocomposites filled by either BaTiO 3 or TiO 2 nanowires. The nanocomposite film with 5 wt % BaTiO 3 @TiO 2 nanowires possesses an ultrahigh discharged energy density of 9.95 J cm -3 at 500 MV m -1 , much higher than that of commercial biaxial-oriented polypropylene (BOPP) (3.56 J cm -3 at 600 MV m -1 ). This new strategy and corresponding results presented here provide new insights into the design of dielectric polymer nanocomposites with high electrical energy storage capability.

Zr-doped TiO2 as a thermostabilizer in plasmon-enhanced dye-sensitized solar cells

Science.gov (United States)

Pasche, Anastasia; Grohe, Bernd; Mittler, Silvia; Charpentier, Paul A.

2017-07-01

Harvesting solar energy is a promising solution toward meeting the world's ever-growing energy demand. Dye-sensitized solar cells (DSSCs) are hybrid organic-inorganic solar cells with tremendous potential for commercial application, but they are plagued by inefficiency due to their poor sunlight absorption. Plasmonic silver nanoparticles (AgNPs) have been shown to enhance the absorptive properties of DSSCs, but their plasmonic resonance can cause thermal damage resulting in cell deterioration. Hence, the influence of Zr-doped TiO2 on the efficiency of plasmon-enhanced DSSCs was studied, showing that 5 mol.% Zr-doping of the photoactive TiO2 material can improve the photovoltaic performance of DSSCs by 44%. By examining three different DSSC designs, it became clear that the efficiency enhancing effect of Zr strongly depends on the proximity of the Zr-doped material to the plasmonic AgNPs.

Surface modification of TiO{sub 2} nanotubes with osteogenic growth peptide to enhance osteoblast differentiation

Energy Technology Data Exchange (ETDEWEB)

Lai, Min, E-mail: minlai@jsnu.edu.cn [School of Life Science, Jiangsu Normal University, Xuzhou, Jiangsu 221116 (China); Jin, Ziyang [School of Life Science, Jiangsu Normal University, Xuzhou, Jiangsu 221116 (China); Su, Zhiguo [Department of Pharmacy, The Affiliated hospital of Qingdao University, Qingdao, Shandong 266555 (China)

2017-04-01

To investigate the influence of surface-biofunctionalized substrates on osteoblast behavior, a layer of aligned TiO{sub 2} nanotubes with a diameter of around 70 nm was fabricated on titanium surface by anodization, and then osteogenic growth peptide (OGP) was conjugated onto TiO{sub 2} nanotubes through the intermediate layer of polydopamine. The morphology, composition and wettability of different surfaces were characterized by field-emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and contact angle measurements, respectively. The effects of OGP-modified TiO{sub 2} nanotube substrates on the morphology, proliferation and differentiation of osteoblasts were examined in vitro. Immunofluorescence staining revealed that the OGP-functionalized TiO{sub 2} nanotubes were favorable for cell spreading. However, there was no significant difference in cell proliferation observed among the different groups. Cells grown onto OGP-functionalized TiO{sub 2} nanotubes showed significantly higher (p < 0.05 or p < 0.01) levels of alkaline phosphatase (ALP) and mineralization after 4, 7 and 14 days of culture, respectively. Cells grown on OGP-functionalized TiO{sub 2} nanotubes had significantly higher (p < 0.05 or p < 0.01) expression of osteogenic-related genes including runt related transcription factor 2 (Runx2), ALP, collagen type I (Col I), osteopontin (OPN) and osteocalcin (OC) after 14 days of culture. These data suggest that surface functionalization of TiO{sub 2} nanotubes with OGP was beneficial for cell spreading and differentiation. This study provides a novel platform for the development and fabrication of titanium-based implants that enhance the propensity for osseointegration between the native tissue and implant interface. - Highlights: • The OGP functionalized TiO{sub 2} nanotube substrates were successfully fabricated through a direct and effective method. • The OGP functionalized substrates

Tuning metal support interactions enhances the activity and durability of TiO2-supported Pt nanocatalysts

International Nuclear Information System (INIS)

Hsieh, Bing-Jen; Tsai, Meng-Che; Pan, Chun-Jern; Su, Wei-Nien; Rick, John; Chou, Hung-Lung; Lee, Jyh-Fu; Hwang, Bing-Joe

2017-01-01

Highlights: • The coverage of TiO x on Pt can be modified by thermal and fluoric acid treatments. • Strong metal support interaction (SMSI) can be testified by electrochemical method. • For the first time, the SMSI effect is observed at 200 °C with supporting TEM images. • Increased activity and stability are attributed to stronger SMSI. • This tunable approach is valid for other oxide supported catalysts, e.g. Pt/Nb-TiO 2 . - Abstract: A facile approach to enhance catalytic activity and durability of TiO 2 -supported Pt nanocatalysts by tuning strong metal support interaction (SMSI) is investigated in this work. No need for a high temperature treatment, the strong metal-support interaction (SMSI) in TiO 2 -supported Pt can be induced at 200° C by H 2 reduction. Moreover, electrochemical methods (methanol oxidation reaction and cyclic voltammetry) are first reported ever to be effective characterization tools for the coverage state caused by SMSI. In addition, the SMSI has also been confirmed by X-ray photoelectron spectroscopy, X-ray absorption spectroscopy, and Transmission Electron Microscopy. It is found that the encapsulation of TiO 2-x species on the surface Pt clusters was induced and modified by thermal reduction and fluoric acid treatment. The catalytic activity and durability of the TiO 2 -supported Pt nanocatalysts are strongly dependent of the state of SMSI. The proposed SMSI-tunable approach to enhance the ORR activity and stability is also proved applicable to Pt/Ti 0.9 Nb 0.1 O 2 nanocatalysts. We believe that the reported approach paves the way for manipulating the activity and stability of other TiO 2 -supported metal nanocatalysts. Furthermore, the suggested electrochemical methods offer facile and effective ways to verify the presence of coverage state before combining with other physical analysis.

S-TiO2/S-reduced graphene oxide for enhanced photoelectrochemical water splitting

Science.gov (United States)

Elbakkay, Mohamed H.; El Rouby, Waleed M. A.; El-Dek, S. I.; Farghali, Ahmed A.

2018-05-01

Sulfur-doped titanium oxide on the surface of sulfur-doped reduced graphene oxide nanocomposites (S-TiO2/S-RGO) were successfully synthesized for the first time through a simple low cost solvothermal reaction process. The sulfur doping was detected in both TiO2 matrix and carbon framework structure of reduced graphene oxide using X-ray photoelectron spectroscopy (XPS) and Energy-dispersive X-ray spectroscopy (EDX). Cross-sectional AFM analysis of S-RGO nanosheets reveals a thickness of 0.51 nm which is much thinner than those previously reported of heteroatom doped-RGO, confirming the single-layer feature. When the as-prepared (S-TiO2/S-RGO) nanocomposites are utilized as photoanodes for photoelectrochemical (PEC) water splitting, they exhibited an enhanced photoelectrochemical performance and long-term stability. The photocurrent density of S-TiO2/S-RGO(0.2) photoanode revealed 3.36 mA/cm2 at 1 V vs Ag/AgCl which is considered 3 times compared to bare synthesized TiO2. This improvement in the photocurrent density was attributed to the increased separation rate of photogenerated electrons and holes and efficient visible light harvesting as a result of the successful combination of the S-TiO2 and the S-RGO in the same nanocomposite photoanode. This promising result presents a new approach for the synthesis of high-efficient future metal-free photoelectrocatalysts.

Ti-Al-Si-C-N hard coatings synthesized by hybrid arc enhanced magnetron sputtering

International Nuclear Information System (INIS)

Wu, Guizhi; Liu, Sitao; Ma, Shengli; Xu, Kewei; Vincent, Ji; Chu, Paul K.

2010-01-01

Ti-Al-Si-C-N coatings are deposited by hybrid arc-enhanced magnetic sputtering and characterized by various micro- and macro-tools. X-ray diffraction, high-resolution transmission electron microscopy, and X-ray photoelectron spectroscopy reveal that the coatings are nanocomposites consisting of nanocrystallites and amorphous phases. They are generally in the form of nc-(Ti,Al)(C,N)/a-Si_3N_4/a-C depending on the composition of the coatings. With increasing Al concentrations, the X-ray diffraction peaks shift to a lower angle indicating compressive stress in the coatings. The measured hardness also diminishes implying reduced contributions from the self-organized stable nanostructure. The dry friction coefficients of the Ti-Al-Si-C-N coatings are found to be about 0.3 which is lower than that of conventional Ti-Si-N coatings. These coatings can find potential applications requiring high temperature with heavy contact loading. (author)

Enhancement of tributyltin degradation under natural light by N-doped TiO{sub 2} photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Bangkedphol, S., E-mail: sornnarin.bangkedphol@strath.ac.uk [David Livingstone Centre for Sustainability, Department of Civil Engineering, University of Strathclyde, Glasgow, Scotland G1 1XN (United Kingdom); Keenan, H.E. [David Livingstone Centre for Sustainability, Department of Civil Engineering, University of Strathclyde, Glasgow, Scotland G1 1XN (United Kingdom); Davidson, C.M. [WestCHEM, Department of Pure and Applied Chemistry, University of Strathclyde, Glasgow, Scotland G1 1XL (United Kingdom); Sakultantimetha, A. [David Livingstone Centre for Sustainability, Department of Civil Engineering, University of Strathclyde, Glasgow, Scotland G1 1XN (United Kingdom); Sirisaksoontorn, W.; Songsasen, A. [Department of Chemistry and Centre for Innovation in chemistry, Faculty of Science, Kasetsart University, Bangkok 10900 (Thailand)

2010-12-15

Photo-degradation of tributyltin (TBT) has been enhanced by TiO{sub 2} nanoparticles doped with nitrogen (N-doped TiO{sub 2}). The N-doped catalyst was prepared by a sol-gel reaction of titanium (IV) tetraisopropoxide with 25% ammonia solution and calcined at various temperatures from 300 to 600 deg. C. X-ray diffraction results showed that N-doped TiO{sub 2} remained amorphous at 300 deg. C. At 400 deg. C the anatase phase occurred then transformed to the rutile phase at 600 deg. C. The crystallite size calculated from Scherrer's equation was in the range of 16-51 nm which depended on the calcination temperature. N-doped TiO{sub 2} calcined at 400 deg. C which contained 0.054% nitrogen, demonstrated the highest photocatalytic degradation of TBT at 28% in 3 h under natural light when compared with undoped TiO{sub 2} and commercial photocatalyst, P25-TiO{sub 2} which gave 14.8 and 18% conversion, respectively.

Fe/Ti co-pillared clay for enhanced arsenite removal and photo oxidation under UV irradiation

Energy Technology Data Exchange (ETDEWEB)

Li, Yuan [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Guang Dong Electric Power Design Institute, China Energy Engineering Group Co. Ltd., Guangzhou 510663 (China); Cai, Xiaojiao [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Guo, Jingwei [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); The 718th Research Institute of CSIC, Handan 056027 (China); Zhou, Shimin [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Na, Ping, E-mail: naping@tju.edu.cn [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China)

2015-01-01

Graphical abstract: - Highlights: • An iron and titanium co-pillared montmorillonite (Fe-Ti/MMT) was synthesized for arsenite removal. • Variety of characterization results indicated that Fe and Ti species were pillared in MMT. • A possible mechanism of arsenite adsorption/oxidation with UV light was established. • The participation of Fe component can promote the process of photocatalytic oxidation in Fe-Ti/MMT + As(III) system. • Fe-Ti/MMT can function as both photocatalyst and adsorbent for arsenite removal. - Abstract: A series of iron and titanium co-pillared montmorillonites (Fe-Ti/MMT) were prepared using hydrolysis of inserted titanium and different iron content in montmorillonite (MMT). The Fe-Ti/MMT were characterized by X-ray fluorescence, N{sub 2} adsorption and desorption, X-ray diffraction, scanning electron microscopy (SEM) and transmission electron microscopy (TEM), confirming the effective insertion of Fe species and TiO{sub 2} in the MMT. The Fe-Ti/MMT was used to remove arsenite (As(III)) from aqueous solutions under different conditions. The result of As(III) adsorption under UV irradiation showed that the photo activity can be enhanced by incorporating Fe and Ti in MMT. Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) analysis indicated that the hydroxyl groups bonded to metal oxide (M–OH) played an important role in the adsorption of As(III)

Enhanced photocatalysis, colloidal stability and cytotoxicity of synchrotron X-ray synthesized Au/TiO2 nanoparticles

International Nuclear Information System (INIS)

Liu, Chi-Jen; Yang, Tsung-Yeh; Wang, Chang-Hai; Chien, Chia-Chi; Chen, Shin-Tai; Wang, Cheng-Liang; Leng, Wei-Hua; Hwu, Y.; Lin, Hong-Ming; Lee, Yao-Chang; Cheng, Chia-Liang; Je, J.H.; Margaritondo, G.

2009-01-01

Au/TiO 2 nanocomposite particles were synthesized by a method based on intense X-ray irradiation without adding any reducing agent or stabilizer. The nanocomposite exhibits promising photocatalytic and biological properties at physiologically relevant concentration ([Au] = 0.028 mM, [TiO 2 ] = 0.5 mM). The structure and photocatalysis were examined by X-ray diffraction, electron microscopy and ultraviolet-visible spectroscopy demonstrating that gold nanoparticles of 2-5 nm size were successfully deposited on TiO 2 nanoparticle surfaces. The nanocomposite exhibited good colloidal stability within a typical cellular environment and was nontoxic to cancer cell according to evaluations under controlled conditions. The Au/TiO 2 nanoparticles were also found to enhance the photocatalytic efficiency of UV radiation and even more that of X-ray radiation. In vitro studies indicated that the cell-killing effect under X-ray irradiation is more pronounced with the addition of Au/TiO 2 nanoparticles than of bare TiO 2 nanoparticles.

Enhancement of polarization property of silane-modified BaTiO3 nanoparticles and its effect in increasing dielectric property of epoxy/BaTiO3 nanocomposites

Directory of Open Access Journals (Sweden)

Thi Tuyet Mai Phan

2016-03-01

Full Text Available The surface modification of synthesized nano-BaTiO3 particles was carried out using γ-aminopropyl trimethoxy silane (γ-APS in an ethanol/water solution. The modified particles were characterized by FTIR, TGA, surface charge analysis, and by dielectric constant measurement. The silane molecules were attached to the surface of BaTiO3 particles through SiOBaTiO3 bonds. The γ-APS grafted on BaTiO3 made the dielectric constant of the particles increase at frequencies ≥0.3 kHz in a wide range of temperature (25 °C–140 °C, due to the presence of NH2 groups. The dependence of the polarization vs. electrical field was measured in order to elucidate the dielectric behavior of the silane treated BaTiO3 in comparison to untreated BaTiO3. The nanocomposite based on epoxy resin containing BaTiO3 nanoparticles untreated and treated with γ-APS was also prepared and characterized. The results indicated that the γ-APS-modified BaTiO3 surfaces significantly enhanced the dielectric property of the nanocomposite.

Electrodeposition of gold nanoparticles on mesoporous TiO{sub 2} photoelectrode to enhance visible region photocurrent

Energy Technology Data Exchange (ETDEWEB)

Supriyono,; Krisnandi, Yuni Krisyuningsih; Gunlazuardi, Jarnuzi, E-mail: jarnuzi@ui.ac.id [Department of Chemistry, FMIPA, Universitas Indonesia, Kampus UI Depok (Indonesia)

2016-04-19

Electrodeposition of gold nanoparticles (Au NPs) on the mesoporous TiO{sub 2} photoelectrode to enchance visible region photocurrent have been investigated. Mesoporous TiO{sub 2} was prepared by a sol gel method and immobilized to the fluorine doped tin oxide (FTO) substrate by dip coating technique. Gold nanoparticles were electrodeposited on the TiO{sub 2} surface and the result FTO/TiO{sub 2}/Au was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), UV-Vis diffuse reflectance spectroscopy (DRS), and X-ray diffraction (XRD). The generated photocurrent was evaluated with an electrochemical workstation (e-DAQ/e-recorder 401) using 60 W wolfram lamp as visible light source. The photoelectrochemical evaluation indicated that the presence of gold nanoparticles on TiO{sub 2} photoelectrode shall enhance the photocurrent up to 50%.

Energy product enhancement of CoPt films by the alloy addition of Ti

Energy Technology Data Exchange (ETDEWEB)

Liao, W.M. [Department of Materials Science and Engineering, Feng Chia University, Taichung, Taiwan (China)]. E-mail: p8993883@knight.fcu.edu; Chen, S.K. [Department of Materials Science and Engineering, Feng Chia University, Taichung, Taiwan (China); Yuan, F.T. [Department of Materials Science and Engineering, Feng Chia University, Taichung, Taiwan (China); Hsu, C.W. [Department of Materials Science and Engineering, Feng Chia University, Taichung, Taiwan (China); Hsiao, S.N. [Department of Materials Science and Engineering, Feng Chia University, Taichung, Taiwan (China); Chang, W.C. [Department of Physics, National Chung Cheng University, Ming-Hsiung, Chia-Yi, Taiwan (China)

2006-09-15

Ternary (Co{sub 48}Pt{sub 52}){sub 100-x}Ti{sub x} (x=0, 0.8, 3.7, 5.3) films were deposited on quartz substrates by RF sputtering at the annealing temperatures T{sub a}=500-800deg. C. The addition of Ti was found to suppress the formation of the CoPt-ordered phase. The coercivity squareness parameters (S*) were also increased with the addition of titanium. TEM observations indicated that the Ti addition significantly reduces the grain size of the CoPt film, thus enhances the exchange interaction between the magnetic grains. The advantages result in the increase of (BH){sub max} values from 2.91MGOe for x=0.0 to 6.09 MGOe for x=5.3 after the samples is annealed at an optimum temperature of 700deg. C.

Enhanced apatite formation on Ti metal heated in PO2-controlled nitrogen atmosphere.

Science.gov (United States)

Hashimoto, Masami; Hayashi, Kazumi; Kitaoka, Satoshi

2013-10-01

The oxynitridation of biomedical titanium metal under a precisely regulated oxygen partial pressure (PO2) of 10(-14)Pa in nitrogen atmosphere at 973 K for 1 h strongly enhanced apatite formation compared with that on Ti heated in air. The factors governing the high apatite-forming ability are discussed from the viewpoint of the surface properties of Ti heated under a PO2 of 10(-14)Pa in nitrogen atmosphere determined from X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and zeta potential measurements. Nitrogen (N)-doped TiO2 (interstitial N) was formed on pure Ti heated under a PO2 of 10(-14)Pa in nitrogen atmosphere at 973 K. The XPS O1s main peak shifted toward a lower binding energy upon heating under a PO2 of 10(-14)Pa. This shift may be due to the formation of oxygen vacancies. This Ti surface had a positive zeta potential of approximately 20 mV. According to time-of-flight secondary ion mass spectroscopy results, PO4(3-) ions were predominantly adsorbed on Ti soaked in simulated body fluid (SBF) after heat treatment, followed by calcium ions. It was concluded that the apatite formation kinetics can be described using the Avrami-Erofeev equation with an Avrami index of n=2, which implies the instantaneous nucleation of apatite on the surface of Ti soaked in SBF after heat treatment at 973 K under a PO2 of 10(-14)Pa. Copyright © 2013 Elsevier B.V. All rights reserved.

Enhanced Photocatalytic Degradation of Methyl Orange Dye under the Daylight Irradiation over CN-TiO₂ Modified with OMS-2.

Science.gov (United States)

Hassan, Mohamed Elfatih; Chen, Jing; Liu, Guanglong; Zhu, Duanwei; Cai, Jianbo

2014-12-12

In this study, CN-TiO₂ was modified with cryptomelane octahedral molecular sieves (OMS-2) by the sol-gel method based on the self-assembly technique to enhance its photocatalytic activity under the daylight irradiation. The synthesized samples were characterized by X-ray diffraction (XRD), UV-vis spectroscopy, Fourier transform infrared spectroscopy (FT-IR) and porosimeter analysis. The results showed that the addition of OMS-2 in the sol lead to higher Brunauer-Emmett-Teller (BET) surface area, pore volume, porosity of particle after heat treatment and the specific surface area, porosity, crystallite size and pore size distribution could be controlled by adjusting the calcination temperature. Compared to the CN-TiO₂-400 sample, CN-TiO₂/OMS-2-400 exhibited greater red shift in absorption edge of samples in visible region due to the OMS-2 coated. The enhancement of photocatalytic activity of CN-TiO₂/OMS-2 composite photocatalyst was subsequently evaluated for the degradation of the methyl orange dye under the daylight irradiation in water. The results showed that the methyl orange dye degradation rate reach to 37.8% for the CN-TiO₂/OMS-2-400 sample under the daylight irradiation for 5 h, which was higher than that of reference sample. The enhancement in daylight photocatalytic activities of the CN-TiO₂/OMS samples could be attributed to the synergistic effects of OMS-2 coated, larger surface area and red shift in adsorption edge of the prepared sample.

Al-doped TiO{sub 2} mesoporous material supported Pd with enhanced catalytic activity for complete oxidation of ethanol

Energy Technology Data Exchange (ETDEWEB)

Zhu, Jing, E-mail: mlczjsls123@163.com; Mu, Wentao, E-mail: mwt15035687833@163.com; Su, Liqing, E-mail: suliqing0163@163.com; Li, Xingying, E-mail: lixingying0479@link.tyut.edu.cn; Guo, Yuyu, E-mail: guoyuyu0455@link.tyut.edu.cn; Zhang, Shen, E-mail: zhangshen0472@link.tyut.edu.cn; Li, Zhe, E-mail: lizhe@tyut.edu.cn

2017-04-15

Pd catalysts supported on Al-doped TiO{sub 2} mesoporous materials were evaluated in complete oxidation of ethanol. The catalysts synthesized by wet impregnation based on evaporation-induced self-assembly were characterized by X-ray diffraction, measurement of pore structure, XPS, FT-IR, temperature programmed reduction and TEM. Characteristic results showed that the aluminium was doped into the lattice of mesoporous anatase TiO{sub 2} to form Al-O-Ti defect structure. Catalytic results revealed that Al-doped catalysts were much more active than the pristine one, especially at low temperature (≤200 °C). This should be ascribed to the introduction of aluminium ions that suppressed the strong metal-support interaction and increased the active sites of Pd oxides, enhanced the stabilized anatase TiO{sub 2}, improved well dispersed high valence palladium species with high reducibility and enriched chemisorption oxygen. - Graphical abstract: Al-doped Pd/TiO{sub 2} exhibited optimal catalytic performance for ethanol oxidation and CO{sub 2} yield by the suppression of SMSI. - Highlights: • Palladium catalysts supported on Al-doped TiO{sub 2} mesoporous materials were studied. • The introduction of Al can enhance anatase stabilization and increase defect TiO{sub 2}. • The Pd/Al-TiO{sub 2} catalysts show higher ethanol conversion and CO{sub 2} yield than Pd/TiO{sub 2}. • The influence of Al on SMSI and catalytic performance were evaluated by TPR and XPS.

Texture-enhanced Al-Cu electrodes on ultrathin Ti buffer layers for high-power durable 2.6 GHz SAW filters

Science.gov (United States)

Fu, Sulei; Wang, Weibiao; Xiao, Li; Lu, Zengtian; Li, Qi; Song, Cheng; Zeng, Fei; Pan, Feng

2018-04-01

Achieving high resistance to acoustomigration and electromigration in the electrodes used in high-power and high-frequency surface acoustic wave (SAW) filters is important to mobile communications development. In this study, the effects of the Ti buffer layers on the textures and acoustomigration and electromigration resistances of the Al-Cu electrodes were studied comprehensively. The results demonstrate that both power durability and electromigration lifetime are positively correlated with the Al-Cu electrode texture quality. Ultrathin (˜2 nm) Ti can lead to the strongest Al-Cu (111) textured electrodes, with a full width at half maximum of the rocking curve of 2.09°. This represents a remarkable enhancement of the power durability of high-frequency 2.6 GHz SAW filters from 29 dBm to 35 dBm. It also produces lifetime almost 7 times longer than those of electrodes without Ti buffer layers in electromigration tests. X-ray diffraction and transmission electron microscopy analyses revealed that these improved acoustomigration and electromigration resistances can be attributed primarily to the reductions in overall and large-angle grain boundaries in the highly Al-Cu (111) textured electrodes. Furthermore, the growth mechanism of highly Al-Cu texture films is discussed in terms of surface-interface energy balance.

TiO2 Nanorod Arrays Based Self-Powered UV Photodetector: Heterojunction with NiO Nanoflakes and Enhanced UV Photoresponse.

Science.gov (United States)

Gao, Yanyan; Xu, Jianping; Shi, Shaobo; Dong, Hong; Cheng, Yahui; Wei, Chengtai; Zhang, Xiaosong; Yin, Shougen; Li, Lan

2018-04-04

The self-powered ultraviolet photodetectors (UV PDs) have attracted increasing attention due to their potential applications without consuming any external power. It is important to obtain the high-performance self-powered UV PDs by a simple method for the practical application. Herein, TiO 2 nanorod arrays (NRs) were synthesized by hydrothermal method, which were integrated with p-type NiO nanoflakes to realize a high performance pn heterojunction for the efficient UV photodetection. TiO x thin film can improve the morphological and carrier transport properties of TiO 2 NRs and decrease the surface and defect states, resulting in the enhanced photocurrent of the devices. NiO/TiO 2 nanostructural heterojunctions show excellent rectifying characteristics (rectification ratio of 2.52 × 10 4 and 1.45 × 10 5 for NiO/TiO 2 NRs and NiO/TiO 2 NRs/TiO x , respectively) with a very low reverse saturation current. The PDs based on the heterojunctions exhibit good spectral selectivity, high photoresponsivity, and fast response and recovery speeds without external applied bias under the weak light radiation. The devices demonstrate good stability and repeatability under UV light radiation. The self-powered performance could be attributed to the proper built-in electric field of the heterojunction. TiO 2 NRs and NiO nanoflakes construct the well-aligned energy-band structure. The enhanced responsivity and detectivity for the devices with TiO x thin films is related to the increased interfacial charge separation efficiency, reduced carrier recombination, and relatively good electron transport of TiO 2 NRs.

Synthesis of CdS Sensitized TiO2 Photocatalysts: Methylene Blue Adsorption and Enhanced Photocatalytic Activities

Directory of Open Access Journals (Sweden)

A. B. Makama

2016-01-01

Full Text Available A series of CdS/TiO2 nanocomposites with different Cd to Ti molar ratio were synthesized from P25-TiO2 nanopowder using microwave-assisted hydrothermal method. The as-produced powders were characterized by XRD, electron microscopy, EDX, and UV-Vis diffuse reflectance spectroscopy. The adsorption capacity and photocatalytic activity of the samples were investigated using methylene blue as a model pollutant. Sorption tests revealed that the adsorption of MB onto the samples obeys the Freundlich-Langmuir isotherm model. The sorption capacity decreased as follows: TiO2>TCd2>TCd1>TCd3>TCd4. The results of the photocatalytic tests under high-intensity discharge (HID lamp revealed that CdS/TiO2 powders with low Cd to Ti molar ratios exhibited much higher activities than P25-TiO2. The CdS/TiO2 sample with 20% CdS/(TCd2 showed the most activity among all these samples. The results also show that the Cd to Ti molar ratio of the nanocomposite has a significant effect on the photodegradation of MB and the enhanced activities exhibited by the nanocomposites are because of the low rate of electron-hole recombination.

Enhanced photocatalytic activity of microwave treated TiO2 pillared montmorillonite

International Nuclear Information System (INIS)

Sun Shenmei; Jiang Yinshan; Yu Lixin; Li Fangfei; Yang Zhengwen; Hou Tianyi; Hu Daqiang; Xia Maosheng

2006-01-01

TiO 2 pillared montmorillonite synthesized by microwave irradiation, exhibited good photocatalytic degradation performance of methyl orange, whose pseudo first order reaction rate constant was nearly four times than that of conventional method, because of its enhanced crystalline, preferred anatase phase and improved porosity performance, which were analysed by X-ray diffraction (XRD), far Fourier transform infrared ray spectroscopy (FTIR) and nitrogen adsorption isotherms

Ultrathin TiO2 layer coated-CdS spheres core-shell nanocomposite with enhanced visible-light photoactivity.

Science.gov (United States)

Chen, Zhang; Xu, Yi-Jun

2013-12-26

Development of various strategies for controllable fabrication of core-shell nanocomposites (CSNs) with highly active photocatalytic performance has been attracting ever-increasing research attention. In particular, control of the ultrathin layer TiO2 shell in constructing CSNs in an aqueous phase is a significant but technologically challenging issue. Here, this paper demonstrates the interface assembly synthesis of CdS nanospheres@TiO2 core-shell photocatalyst via the electrostatic interaction of negatively charged water-stable titania precursor with positively charged CdS nanospheres (CdS NSPs), followed by the formation of the ultrathin-layer TiO2 shell through a facile refluxing process in aqueous phase. The as-formed CdS NSPs@TiO2 core-shell nanohybrid exhibits a high visible-light-driven photoactivity for selective transformation and reduction of heavy metal ions. The ultrathin TiO2 layer coated on CdS NSPs results in excellent light transmission property, enhanced adsorption capacity, and improved transfer of charge carriers and lifespan of photoinduced electron-hole pairs, which would prominently contribute to the significant photoactivity enhancement. It is anticipated that this facile aqueous-phase synthesis strategy could be extended to design a variety of more efficient CSN photocatalysts with controllable morphology toward target applications in diverse photoredox processes.

Development of re-crystallized W-1.1%TiC with enhanced room-temperature ductility and radiation performance

International Nuclear Information System (INIS)

Kurishita, H.; Matsuo, S.; Arakawa, H.; Sakamoto, T.; Kobayashi, S.; Nakai, K.; Takida, T.; Kato, M.; Kawai, M.; Yoshida, N.

2010-01-01

Ultra-fine grained (UFG) W-TiC compacts fabricated by powder metallurgical methods utilizing mechanical alloying (MA) are very promising for use in irradiation environments. However, the assurance of room-temperature ductility and enhancement in surface resistances to low-energy hydrogen irradiation are unsettled issues. As an approach to solution to these, microstructural modification by hot plastic working has been applied to UFG W-TiC processed by MA in a purified Ar or H 2 atmosphere and hot isostatic pressing (HIP). Hot plastically worked compacts have been subjected to 3-point bend tests at room temperature and TEM microstructural examinations. It is found that the microstructural modification allows us to convert UFG W-1.1%TiC to compacts exhibiting a very high fracture strength and appreciable ductility at room temperature. The compacts of W-1.1%TiC/Ar (MA atmosphere: Ar) and W-1.1%TiC/H 2 (MA atmosphere: H 2 ) exhibit re-crystallized structures with approximately 0.5 and 1.5 μm in grain size, respectively. It is shown that the enhancement of fracture resistance by microstructural modifications is attributed to significant strengthening of weak grain boundaries in the re-crystallized state. As a result the modified compacts exhibit superior surface resistance to low-energy deuteron irradiation.

Facile synthesis and enhanced magnetic, photocatalytic properties of one-dimensional Ag@Fe{sub 3}O{sub 4}-TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Jia, Xiaohua, E-mail: xhjia2003@126.com [School of Environment and Safety Engineering, Jiangsu University, Zhenjiang, Jiangsu, 212013 (China); Dai, Rongrong; Lian, Dandan; Han, Song [School of Environment and Safety Engineering, Jiangsu University, Zhenjiang, Jiangsu, 212013 (China); Wu, Xiangyang, E-mail: wuxy@ujs.edu.cn [School of Environment and Safety Engineering, Jiangsu University, Zhenjiang, Jiangsu, 212013 (China); Song, Haojie [Institute of Polymer Materials, School of Materials Science & Engineering, Jiangsu University, Zhenjiang 212013 (China)

2017-01-15

Highlights: • One-dimensional triple heterostructure Ag@Fe{sub 3}O{sub 4}-TiO{sub 2} was successfully achieved by a facile co-precipitation and chemical-solution-deposition process method. • One-dimensional triple heterostructure Ag@Fe{sub 3}O{sub 4}-TiO{sub 2} exhibited enhanced photocatalytic properties and can be easily recovered by an extemal magnetic field. • The mechanisms for the enhanced photocatalytic effect of the heterostructure were discussed. - Abstract: Fe{sub 3}O{sub 4}-TiO{sub 2} heterostructures were synthesized through co-precipitation method based on TiO{sub 2} nanobelts. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), vibration sample magnetometry (VSM) were used to characterize the heterostructure nanocomposites. The results of XRD proved that the TiO{sub 2} nanobelt was anatase which was the most suitable crystal form for photocatalysis. SEM and TEM analysis indicated that Fe{sub 3}O{sub 4} nanoparticles were adhere to TiO{sub 2} nanobelts which have one-dimensional structure with 100–200 nm in width. The VSM measurements showed that the photocatalyst can be easily recovered by an extemal magnetic field. X-ray photoelectron spectroscopy (XPS) of Ag@Fe{sub 3}O{sub 4}-TiO{sub 2} nanocomposites studies confirm that Ag is in Ag{sup 0} state. Finally, the photodegradation of rhodamine B (RhB) by the obtained magnetic photocatalyst was investigated via UV–vis absorption spectra. The photocatalytic activity of the composites was observed to be lower compared to bare TiO{sub 2} due to the higher degree of recombination reactions after combined with Fe{sub 3}O{sub 4} nanoparticles. After coated the composite of 15% Fe{sub 3}O{sub 4}-TiO{sub 2} with Ag, the new nanocomposite of Ag@Fe{sub 3}O{sub 4}-TiO{sub 2} can be easily recovered after photocatalysis by an extemal magnetic field and showed enhanced photocatalytic activity. The mechanisms for the exhibited enhanced photocatalytic effect of

Ag-loaded TiO2/reduced graphene oxide nanocomposites for enhanced visible-light photocatalytic activity

International Nuclear Information System (INIS)

Vasilaki, E.; Georgaki, I.; Vernardou, D.; Vamvakaki, M.; Katsarakis, N.

2015-01-01

Highlights: • Ag nanoparticles were loaded on TiO 2 by chemical reduction. • TiO 2 /Ag and TiO 2 samples were deposited on reduced graphene oxide (rGO). • Their performance was evaluated via methylene blue removal under visible-light. • TiO 2 /Ag/rGO presented superior activity compared to TiO 2 , TiO 2 /Ag and TiO 2 /rGO. - Abstract: In this work, Ag nanoparticles were loaded by chemical reduction onto TiO 2 P25 under different loadings ranging from 1 up to 4 wt% and hydrothermally deposited on reduced graphene oxide sheets. Chemical reduction was determined to be an effective preparation approach for Ag attachment to titania, leading to the formation of small silver nanoparticles with an average diameter of 4.2 nm. The photocatalytic performance of the hybrid nanocomposite materials was evaluated via methylene blue (MB) dye removal under visible-light irradiation. The rate of dye decolorization was found to depend on the metal loading, showing an increase till a threshold value of 3 wt%, above which the rate drops. Next, the as prepared sample of TiO 2 /Ag of better photocatalytic response, i.e., at a 3 wt% loading value, was hydrothermally deposited on a platform of reduced graphene oxide (rGO) of tunable content (mass ratio). TiO 2 /Ag/rGO coupled nanocomposite presented significantly enhanced photocatalytic activity compared to the TiO 2 /Ag, TiO 2 /rGO composites and bare P25 titania semiconductor photocatalysts. In particular, after 45 min of irradiation almost complete decolorization of the dye was observed for the TiO 2 /Ag/rGO nanocatalyst, while the respective removal efficiency was 92% for TiO 2 /Ag, 93% for TiO 2 /rGO and only 80% for the bare TiO 2 nanoparticles. This simple step by step preparation strategy allows for optimum exploitation of the advanced properties of metal plasmonic effect and reduced graphene oxide as the critical host for boosting the overall photocatalytic activity towards visible-light.

Enhanced photoelectrochemical performance of PbS sensitized Sb–SnO{sub 2}/TiO{sub 2} nanotube arrays electrode under visible light illumination

Energy Technology Data Exchange (ETDEWEB)

Wu, Jia; Tang, Chengli [Department of Environmental Science and Engineering, Xi’an Jiaotong University, Xi’an 710049 (China); Xu, Hao, E-mail: xuhao@mail.xjtu.edu.cn [Department of Environmental Science and Engineering, Xi’an Jiaotong University, Xi’an 710049 (China); Yan, Wei, E-mail: yanwei@mail.xjtu.edu.cn [Department of Environmental Science and Engineering, Xi’an Jiaotong University, Xi’an 710049 (China); State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049 (China)

2015-06-05

Highlights: • Sb–SnO{sub 2} is used to modify TiO{sub 2} NTAs by microwave method. • PbS is employed to sensitive Sb–SnO{sub 2}/TiO{sub 2} NTAs by S-SILAR method. • Sb–SnO{sub 2} improves electrons transfer and PbS enhances visible light absorption. • The composite electrode shows enhanced photoelectrochemical properties. • The composite electrode exhibits high hydrogen evolution and high QE. - Abstract: The novel PbS sensitized Sb–SnO{sub 2}/TiO{sub 2} nanotube arrays (NTAs) composite electrode (PbS/Sb–SnO{sub 2}/TiO{sub 2} NTAs) was fabricated by microwave combined with sonication-assisted successive ionic layer adsorption and reaction technique (S-SILAR). The obtained electrodes were characterized by field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and UV–Vis diffuse reflectance absorption spectra techniques. Enhanced photocurrent (15.52 mA/cm{sup 2}) of the PbS/Sb–SnO{sub 2}/TiO{sub 2} NTAs electrode was observed and can be attributed to the facile photo-generated electrons transfer and enhanced charge separation efficiency. Furthermore, the PbS/Sb–SnO{sub 2}/TiO{sub 2} NTAs composite electrode shows a higher H{sub 2} production rate than the Sb–SnO{sub 2}/TiO{sub 2} NTAs electrode and PbS/TiO{sub 2} NTAs electrode. The results indicate that the PbS/Sb–SnO{sub 2}/TiO{sub 2} NTAs electrode is a promising photoanode in visible photocatalytic water splitting.

Enhanced photocatalytic activity for H2 evolution under irradiation of UV-vis light by Au-modified nitrogen-doped TiO2.

Science.gov (United States)

Zhao, Weirong; Ai, Zhuyu; Dai, Jiusong; Zhang, Meng

2014-01-01

Photocatalytic water splitting for hydrogen evolution is a potential way to solve many energy and environmental issues. Developing visible-light-active photocatalysts to efficiently utilize sunlight and finding proper ways to improve photocatalytic activity for H2 evolution have always been hot topics for research. This study attempts to expand the use of sunlight and to enhance the photocatalytic activity of TiO2 by N doping and Au loading. Au/N-doped TiO2 photocatalysts were synthesized and successfully used for photocatalytic water splitting for H2 evolution under irradiation of UV and UV-vis light, respectively. The samples were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV-vis diffuse reflectance spectroscopy (DRS), photoluminescence spectroscopy (PL), and photoelectrochemical characterizations. DRS displayed an extension of light absorption into the visible region by doping of N and depositing with Au, respectively. PL analysis indicated electron-hole recombination due to N doping and an efficient inhibition of electron-hole recombination due to the loaded Au particles. Under the irradiation of UV light, the photocatalytic hydrogen production rate of the as-synthesized samples followed the order Au/TiO2 > Au/N-doped TiO2 > TiO2 > N-doped TiO2. While under irradiation of UV-vis light, the N-TiO2 and Au/N-TiO2 samples show higher H2 evolution than their corresponding nitrogen-free samples (TiO2 and Au/TiO2). This inconsistent result could be attributed to the doping of N and the surface plasmonic resonance (SPR) effect of Au particles extending the visible light absorption. The photoelectrochemical characterizations further indicated the enhancement of the visible light response of Au/N-doped TiO2. Comparative studies have shown that a combination of nitrogen doping and Au loading enhanced the visible light response of TiO2 and increased the utilization of solar energy, greatly

Enhanced photocatalytic activity for H2 evolution under irradiation of UV-vis light by Au-modified nitrogen-doped TiO2.

Directory of Open Access Journals (Sweden)

Weirong Zhao

Full Text Available BACKGROUND PURPOSE: Photocatalytic water splitting for hydrogen evolution is a potential way to solve many energy and environmental issues. Developing visible-light-active photocatalysts to efficiently utilize sunlight and finding proper ways to improve photocatalytic activity for H2 evolution have always been hot topics for research. This study attempts to expand the use of sunlight and to enhance the photocatalytic activity of TiO2 by N doping and Au loading. METHODS: Au/N-doped TiO2 photocatalysts were synthesized and successfully used for photocatalytic water splitting for H2 evolution under irradiation of UV and UV-vis light, respectively. The samples were characterized using X-ray diffraction (XRD, transmission electron microscopy (TEM, X-ray photoelectron spectroscopy (XPS, UV-vis diffuse reflectance spectroscopy (DRS, photoluminescence spectroscopy (PL, and photoelectrochemical characterizations. RESULTS: DRS displayed an extension of light absorption into the visible region by doping of N and depositing with Au, respectively. PL analysis indicated electron-hole recombination due to N doping and an efficient inhibition of electron-hole recombination due to the loaded Au particles. Under the irradiation of UV light, the photocatalytic hydrogen production rate of the as-synthesized samples followed the order Au/TiO2 > Au/N-doped TiO2 > TiO2 > N-doped TiO2. While under irradiation of UV-vis light, the N-TiO2 and Au/N-TiO2 samples show higher H2 evolution than their corresponding nitrogen-free samples (TiO2 and Au/TiO2. This inconsistent result could be attributed to the doping of N and the surface plasmonic resonance (SPR effect of Au particles extending the visible light absorption. The photoelectrochemical characterizations further indicated the enhancement of the visible light response of Au/N-doped TiO2. CONCLUSION: Comparative studies have shown that a combination of nitrogen doping and Au loading enhanced the visible light response of

Influence of electric current on microstructure evolution in Ti/Al and Ti/TiAl{sub 3} during spark plasma sintering

Energy Technology Data Exchange (ETDEWEB)

Sun, Y. [Department of Materials Science and Engineering, Institute of Materials Science, University of Connecticut, Storrs, CT 06269-3136 (United States); Haley, J. [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95616-5294 (United States); Kulkarni, K. [Department of Materials Science and Engineering, Indian Institute of Technology, Kanpur 208016, UP (India); Aindow, M. [Department of Materials Science and Engineering, Institute of Materials Science, University of Connecticut, Storrs, CT 06269-3136 (United States); Lavernia, E.J., E-mail: lavernia@ucdavis.edu [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95616-5294 (United States); Department of Chemical Engineering and Materials Science, University of California, Irvine, CA 92697-2575 (United States)

2015-11-05

The synthesis of γ-TiAl from elemental metals via solid-state reactive diffusion processing routes involves multiple reaction steps with the formation of various intermediate intermetallic compounds, starting with TiAl{sub 3} because this phase is favored kinetically. To understand the processes by which the TiAl{sub 3} intermediate is eliminated during synthesis of γ-TiAl alloy via spark plasma sintering (SPS), the reaction between Ti and TiAl{sub 3} during SPS was studied with emphasis on the effects of the applied electric current and starting TiAl{sub 3} microstructure on the reaction kinetics and the underlying diffusion mechanisms. The intermediate intermetallic phases Ti{sub 3}Al, TiAl and TiAl{sub 2} were formed between the Ti and TiAl{sub 3} upon SPS processing at 900 °C. The applied electric current did not alter the character of the phases formation in the Ti/TiAl{sub 3} system, but thermodynamic calculations suggest that the activation energy for the nucleation of TiAl{sub 2} is reduced significantly with an electric current flowing. Moreover, the kinetics of the reactions between Ti and TiAl{sub 3} were enhanced when the starting TiAl{sub 3} microstructure was refined. The electric field also had a more significant influence on the grain growth kinetics for TiAl{sub 2} and TiAl in powder blend compacts with refined microstructures. - Highlights: • Reaction between Ti and TiAl{sub 3} during spark plasma sintering was studied. • Refined starting TiAl{sub 3} microstructure enhanced the reactions kinetics. • The nucleation barrier of TiAl{sub 2} was reduced by the applied electric field. • The applied electric field restrained the grain growth of TiAl and TiAl{sub 2}.

Antifouling enhancement of polysulfone/TiO2 nanocomposite separation membrane by plasma etching

Science.gov (United States)

Chen, Z.; Yin, C.; Wang, S.; Ito, K.; Fu, Q. M.; Deng, Q. R.; Fu, P.; Lin, Z. D.; Zhang, Y.

2017-01-01

A polysulfone/TiO2 nanocomposite membrane was prepared via casting method, followed by the plasma etching of the membrane surface. Doppler broadened energy spectra vs. positron incident energy were employed to elucidate depth profiles of the nanostructure for the as-prepared and treated membranes. The results confirmed that the near-surface of the membrane was modified by the plasma treatment. The antifouling characteristics for the membranes, evaluated using the degradation of Rhodamin B, indicated that the plasma treatment enhances the photo catalytic ability of the membrane, suggesting that more TiO2 nanoparticles are exposed at the membrane surface after the plasma treatment as supported by the positron result.

Antifouling enhancement of polysulfone/TiO2 nanocomposite separation membrane by plasma etching

International Nuclear Information System (INIS)

Chen, Z; Yin, C; Wang, S; Fu, Q M; Deng, Q R; Fu, P; Lin, Z D; Zhang, Y; Ito, K

2017-01-01

A polysulfone/TiO 2 nanocomposite membrane was prepared via casting method, followed by the plasma etching of the membrane surface. Doppler broadened energy spectra vs. positron incident energy were employed to elucidate depth profiles of the nanostructure for the as-prepared and treated membranes. The results confirmed that the near-surface of the membrane was modified by the plasma treatment. The antifouling characteristics for the membranes, evaluated using the degradation of Rhodamin B, indicated that the plasma treatment enhances the photo catalytic ability of the membrane, suggesting that more TiO 2 nanoparticles are exposed at the membrane surface after the plasma treatment as supported by the positron result. (paper)

In situ glow discharge plasma electrolytic synthesis of reduced TiO2 for enhanced visible light photocatalysis

Science.gov (United States)

Feng, Guang; Wu, Botao; Qayyum Khan, Abdul; Zeng, Heping

2018-05-01

Reduced titanium dioxide (TiO2‑x) due to its extraordinary visible light absorption has been widely investigated in photodegradation and water splitting nowadays. However, conventional routes to synthesize reduced TiO2 usually demand multiple preparation steps, harsh controlled conditions or expensive facilities. Here we developed a single-step in situ approach to prepare the gray TiO2‑x nanoparticles (sub-10 nm) effectively by the glow discharge plasma electrolysis (GDPE) under atmospheric pressure. The co-existence of self-doped oxygen vacancies and Ti3+ in the generated TiO2‑x nanoparticles is demonstrated by electron paramagnetic resonance (EPR). The tunable ratio of bulk/surface defect can be realized by controlling the glow discharge power directly. It should be noticed that Ti3+ in the synthesized TiO2‑x are quite stable in ambient air. The UV–vis spectra of gray TiO2‑x show an enhanced visible light absorption, which leads to high visible-light photocatalytic activity. Moreover, the as-prepared TiO2‑x after 6 months storage still shows excellent stability during photocatalytic reactions. Owing to its simplicity and effectivity, this preparation method with GDPE should provide a large-scale production for TiO2‑x with high photoactivity.

Continuous Synthesis of Ag/TiO2 Nanoparticles with Enhanced Photocatalytic Activity by Pulsed Laser Ablation

Directory of Open Access Journals (Sweden)

Rui Zhou

2017-01-01

Full Text Available A facile and environmental friendly synthesis strategy based on pulsed laser ablation has been developed for potential mass production of Ag-loaded TiO2 (Ag/TiO2 nanoparticles. By sequentially irradiating titanium and silver target substrates, respectively, with the same 1064 nm 100 ns fiber laser, Ag/TiO2 particles can be fabricated. A postannealing process leads to the crystallization of TiO2 to anatase phase with high photocatalytic activity. The phase composition, microstructure, and surface state of the elaborated Ag/TiO2 are characterized by X-ray diffraction (XRD, energy dispersive X-ray (EDX, field emission scanning electron microscope (FESEM, transmission electron microscope (TEM, and X-ray photoelectron spectroscopy (XPS techniques. The results suggest that the presence of silver clusters deposited on the surface of TiO2 nanoparticles. The nanostructure is formed through laser interaction with materials. Photocatalytic activity evaluation shows that silver clusters could significantly enhance the photocatalytic activity of TiO2 in degradation of methylene blue (MB under UV light irradiation, which is attributed to the efficient electron traps by Ag clusters. Our developed Ag/TiO2 nanoparticles synthesized via a straightforward, continuous, and green pathway could have great potential applications in photocatalysis.

Facile synthesis and enhanced visible light photocatalytic activity of N and Zr co-doped TiO2 nanostructures from nanotubular titanic acid precursors

Science.gov (United States)

Zhang, Min; Yu, Xinluan; Lu, Dandan; Yang, Jianjun

2013-12-01

Zr/N co-doped TiO2 nanostructures were successfully synthesized using nanotubular titanic acid (NTA) as precursors by a facile wet chemical route and subsequent calcination. These Zr/N-doped TiO2 nanostructures made by NTA precursors show significantly enhanced visible light absorption and much higher photocatalytic performance than the Zr/N-doped P25 TiO2 nanoparticles. Impacts of Zr/N co-doping on the morphologies, optical properties, and photocatalytic activities of the NTA precursor-based TiO2 were thoroughly investigated. The origin of the enhanced visible light photocatalytic activity is discussed in detail.

Characteristics of Ti{sub 3}C{sub 2}X–Chitosan Films with Enhanced Mechanical Properties

Energy Technology Data Exchange (ETDEWEB)

Hu, Chunfeng, E-mail: chfhu@live.cn [Key Laboratory of Advanced Technologies of Materials, Ministry of Education, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu (China); Shen, Fei [Center of Nanomaterials for Renewable Energy, State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical Engineering, Xi’an Jiaotong University, Xi’an (China); Zhu, Degui [Key Laboratory of Advanced Technologies of Materials, Ministry of Education, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu (China); Zhang, Haibin [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang (China); Xue, Jianming [State Key Laboratory of Nuclear Physics and Technology, Center for Applied Physics and Technology, Peking University, Beijing (China); Han, Xiaogang, E-mail: chfhu@live.cn [Center of Nanomaterials for Renewable Energy, State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical Engineering, Xi’an Jiaotong University, Xi’an (China)

2017-01-25

Chitosan-reinforced Ti{sub 3}C{sub 2}X films were successfully fabricated by infiltrating Ti{sub 3}C{sub 2}X suspensions containing different chitosan contents followed by vacuum drying. The designed chitosan contents were 0, 7, 10, and 14 wt%. It was determined that as-prepared films had shell-like nanolaminar microstructure. Displacement of Ti{sub 3}C{sub 2}X nanosheets increased from 24.254 Å (0 wt%) to 28.822 Å (10 wt%) and then decreased to 28.132 Å (14 wt%) with increment of chitosan content. Tensile strength of films continuously increased from 8.20 to 43.52 MPa, enhancing 5.3 times. Electrical resistivity of films increased from 0.39 mΩ cm (0 wt%) to 54.91 mΩ cm (14 wt%). Only pure Ti{sub 3}C{sub 2}X film could be used as electrode in the sodium battery.

Enhanced Mechanical Properties of MgZnCa Bulk Metallic Glass Composites with Ti-Particle Dispersion

Directory of Open Access Journals (Sweden)

Pei Chun Wong

2016-05-01

Full Text Available Rod samples of Mg60Zn35Ca5 bulk metallic glass composites (BMGCs dispersed with Ti particles have been successfully fabricated via injection casting. The glass forming ability (GFA and the mechanical properties of these Mg-based BMGCs have been systematically investigated as a function of the volume fraction (Vf of Ti particles. The results showed that the compressive ductility increased with Vf. The mechanical performance of these BMGCs, with up to 5.4% compressive failure strain and 1187 MPa fracture strength at room temperature, can be obtained for the Mg-based BMGCs with 50 vol % Ti particles, suggesting that these dispersed Ti particles can absorb the energy of the crack propagations and can induce branches of the primary shear band into multiple secondary shear bands. It follows that further propagation of the shear band is blocked, enhancing the overall plasticity.

Preparation and solar-light photocatalytic activity of TiO2 composites: TiO2/kaolin, TiO2/diatomite, and TiO2/zeolite

Science.gov (United States)

Li, Y.; Li, S. G.; Wang, J.; Li, Y.; Ma, C. H.; Zhang, L.

2014-12-01

Three TiO2 loaded composites, TiO2/kaolin, TiO2/diatomite, and TiO2/zeolite, were prepared in order to improve the solar-light photocatalytic activity of TiO2. The results showed that the photocatalytic activity could obviously be enhanced by loading appropriate amount of inorganic mineral materials. Meanwhile, TiO2 content, heat-treatment temperature and heat-treatment time on the photocatalytic activity were reviewed. Otherwise, the effect of solar light irradiation time and dye concentration on the photocatalytic degradation of Acid Red B was investigated. Furthermore, the degradation mechanism and adsorption process were also discussed.

CdSe nanorod/TiO2 nanoparticle heterojunctions with enhanced solar- and visible-light photocatalytic activity

Directory of Open Access Journals (Sweden)

Fakher Laatar

2017-12-01

Full Text Available CdSe nanorods (NRs with an average length of ≈120 nm were prepared by a solvothermal process and associated to TiO2 nanoparticles (Aeroxide® P25 by annealing at 300 °C for 1 h. The content of CdSe NRs in CdSe/TiO2 composites was varied from 0.5 to 5 wt %. The CdSe/TiO2 heterostructured materials were characterized by XRD, TEM, SEM, XPS, UV–visible spectroscopy and Raman spectroscopy. TEM images and XRD patterns show that CdSe NRs with wurtzite structure are associated to TiO2 particles. The UV–visible spectra demonstrate that the narrow bandgap of CdSe NRs serves to increase the photoresponse of CdSe/TiO2 composites until ≈725 nm. The CdSe (2 wt %/TiO2 composite exhibits the highest photocatalytic activity for the degradation of rhodamine B in aqueous solution under simulated sunlight or visible light irradiation. The enhancement in photocatalytic activity likely originates from CdSe sensitization of TiO2 and the heterojunction between these materials which facilitates electron transfer from CdSe to TiO2. Due to its high stability (up to ten reuses without any significant loss in activity, the CdSe/TiO2 heterostructured catalysts show high potential for real water decontamination.

Enhanced visible-light photocatalytic activity for selective oxidation of amines into imines over TiO2(B)/anatase mixed-phase nanowires

International Nuclear Information System (INIS)

Dai, Jun; Yang, Juan; Wang, Xiaohan; Zhang, Lei; Li, Yingjie

2015-01-01

Graphical abstract: Visible-light photocatalytic activities for selective oxidation of amines into imines are greatly affected by the crystal structure of TiO 2 catalysts and mixed-phase TiO 2 (B)/anatase possess higher photoactivity because of the moderate adsorption ability and efficient charge separation. - Highlights: • Visible-light photocatalytic oxidation of amines to imines is studied over different TiO 2 . • Photocatalytic activities are greatly affected by the crystal structure of TiO 2 nanowires. • Mixed-phase TiO 2 (B)/anatase exhibits higher catalytic activity than single-phase TiO 2 . • Enhanced activity is ascribed to efficient adsorption ability and interfacial charge separation. • Photoinduced charge transfer mechanism on TiO 2 (B)/anatase catalysts is also proposed. - Abstract: Wirelike catalysts of mixed-phase TiO 2 (B)/anatase TiO 2 , bare anatase TiO 2 and TiO 2 (B) are synthesized via calcining precursor hydrogen titanate obtained from hydrothermal process at different temperatures between 450 and 700 °C. Under visible light irradiation, mixed-phase TiO 2 (B)/anatase TiO 2 catalysts exhibit enhanced photocatalytic activity in comparison with pure TiO 2 (B) and anatase TiO 2 toward selective oxidation of benzylamines into imines and the highest photocatalytic activity is achieved by TW-550 sample consisting of 65% TiO 2 (B) and 35% anatase. The difference in photocatalytic activities of TiO 2 samples can be attributed to the different adsorption abilities resulted from their crystal structures and interfacial charge separation driven by surface-phase junctions between TiO 2 (B) and anatase TiO 2 . Moreover, the photoinduced charge transfer mechanism of surface complex is also proposed over mixed-phase TiO 2 (B)/anatase TiO 2 catalysts. Advantages of this photocatalytic system include efficient utilization of solar light, general suitability to amines, reusability and facile separation of nanowires catalysts

TiO2 promoted by two different non-noble metal cocatalysts for enhanced photocatalytic H2 evolution

International Nuclear Information System (INIS)

Lin, Jing-Dong; Yan, Shi; Huang, Qin-Dong; Fan, Mei-Ting; Yuan, You-Zhu; Tan, Timothy Thatt-Yang; Liao, Dai-Wei

2014-01-01

TiO 2 photocatalysts modified by cobalt and nickel cocatalysts were prepared via polymerized complex method (PCM) and evaluated by photocatalytic hydrogen evolution. Hydrogen generation in 6 h for the TiO 2 promoted by cobalt and nickel (0.1%Co + 0.2%Ni/TiO 2 ) is about two times (2456 μmol H 2 ) compared to that of TiO 2 promoted only by cobalt (1180 μmol H 2 for 0.1%Co/TiO 2 ) or nickel (1127 μmol H 2 for 0.2%Ni/TiO 2 ), and mechanically mixed TiO 2 promoted by cobalt and TiO 2 promoted by nickel (0.1%Co/TiO 2 :0.2%Ni/TiO 2 = 1:1 (m/m), 1282 μmol H 2 ). The high photocatalytic H 2 evolution activity over TiO 2 promoted by cobalt and nickel is ascribed to enhanced photo response due to the presence of cobalt and nickel impurity level, and effective separation of photogenerated electrons and holes due to the synergistic effect of cobalt and nickel, which serve as active sites for H 2 evolution reaction (HER) and oxidation reaction (OR) respectively. This study demonstrates a viable strategy to design more active photocatalysts for photocatalytic H 2 evolution by substituting noble metals with more abundant elements using as HER and OR cocatalysts, respectively.

Enhanced photocatalytic degradation of methylene blue on carbon nanotube-TiO{sub 2}-Pd composites

Energy Technology Data Exchange (ETDEWEB)

Kim, Eun Hye; Choi, Hyun Chul [Dept. of Chemistry, Chonnam National University, Gwangju (Korea, Republic of)

2016-11-15

Semiconductor-based photocatalysis is recognized as a promising technique for addressing energy and environmental issues. Among various semiconductors, the use of titanium dioxide (TiO-2) as a photocatalyst in solar energy conversion and pollutant degradation has been widely investigated because of its high efficiency, photostability, and low toxicity. However, its practical application is restricted by the intrinsic wide band gap of TiO-2 and the rapid recombination of photogenerated electron–hole pairs. Therefore, several remedial methods have been proposed, such as the doping of TiO{sub 2} with metallic or non-metallic elements, increasing its surface area, sensitization with dyes, and the generation of defect structures. We have successfully prepared CNT–TiO{sub 2}–Pd composites with a simple two-step sol–gel method. We characterized the composites with TEM and XRD, and demonstrated that anatase TiO{sub 2} and metallic Pd nanoparticles were deposited onto the surfaces of the CNTs. The average particle size of these nanoparticles was approximately 3.4 nm. The prepared catalyst was found to exhibit a higher activity in MB photodegradation than the reference systems. The synergy of the combination of CNTs and Pd nanoparticles with TiO{sub 2} provides superior MB degradation. More comprehensive studies of the mechanism for this synergy between the metal nanoparticles and TiO{sub 2} that enhances the photocatalytic activity of CNT–TiO{sub 2} are underway in our laboratory.

Synthesis and Characterization of Ag-Ag2O/TiO2@polypyrrole Heterojunction for Enhanced Photocatalytic Degradation of Methylene Blue

Directory of Open Access Journals (Sweden)

Rajeev Kumar

2016-05-01

Full Text Available Hybrid multi-functional nanomaterials comprising two or more disparate materials have become a powerful approach to obtain advanced materials for environmental remediation applications. In this work, an Ag-Ag2O/TiO2@polypyrrole (Ag/TiO2@PPy heterojunction has been synthesized by assembling a self-stabilized Ag-Ag2O (p type semiconductor (denoted as Ag and polypyrrole (π-conjugated polymer on the surface of rutile TiO2 (n type. Ag/TiO2@PPy was synthesized through simultaneous oxidation of pyrrole monomers and reduction of AgNO3 in an aqueous solution containing well-dispersed TiO2 particles. Thus synthesized Ag/TiO2@PPy was characterized using X-ray diffraction (XRD, X-ray photoelectron spectroscopy (XPS, field emission scanning electron microscopy (FE-SEM, transmission electron microscopy (TEM, and UV-Vis diffuse reflectance spectroscopy (UV-vis DSR. The photocatalytic activity of synthesized heterojunction was investigated for the decomposition of methylene blue (MB dye under UV and visible light irradiation. The results revealed that π-conjugated p-n heterojunction formed in the case of Ag/TiO2@PPy significantly enhanced the photodecomposition of MB compared to the p-n type Ag/TiO2 and TiO2@PPy (n-π heterojunctions. A synergistic effect between Ag-Ag2O and PPy leads to higher photostability and a better electron/hole separation leads to an enhanced photocatalytic activity of Ag/TiO2@PPy under both UV and visible light irradiations.

Synthesis and Characterization of CdS/TiO2-Montmorillonite Nanocomposite with Enhanced Visible-Light Absorption

OpenAIRE

Feng-shan Zhou; Dai-mei Chen; Bao-lin Cui; Wei-heng Wang

2014-01-01

Sodium montmorillonite (MMT) was chosen as the carrier; a serial of CdS/TiO2-MMT nanocomposites with enhanced visible-light absorption ability was prepared by hydrothermal synthesis method combination with semiconductor compound modification method. The samples are characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and ultraviolet visible (UV-Vis) spectroscopy; the results showed that TiO2 and CdS nanoparticles were loaded on the surface of montmorillonite unifo...

Origin of the Enhanced Visible-Light Absorption in N-Doped Bulk Anatase TiO 2 from First-Principles Calculations

KAUST Repository

Harb, Moussab; Sautet, P.; Raybaud, P.

2011-01-01

unambiguously that the diamagnetic TiO(2-3x)N2x system exhibits the enhanced optical absorption in N-doped TiO2 under visible-light irradiation. Electronic analysis further reveals a band gap narrowing of 0.6 eV induced by delocalized impurity states located

Development of re-crystallized W-1.1%TiC with enhanced room-temperature ductility and radiation performance

Energy Technology Data Exchange (ETDEWEB)

Kurishita, H., E-mail: kurishi@imr.tohoku.ac.j [International Research Center for Nuclear Materials Science, IMR, Tohoku University, Oarai, Ibaraki 311-1313 (Japan); Matsuo, S.; Arakawa, H. [International Research Center for Nuclear Materials Science, IMR, Tohoku University, Oarai, Ibaraki 311-1313 (Japan); Sakamoto, T.; Kobayashi, S.; Nakai, K. [Department of Materials Science and Biotechnology, Ehime University, Matsuyama 790-8577 (Japan); Takida, T.; Kato, M. [A.L.M.T. Corp., Toyama 931-8543 (Japan); Kawai, M. [Institute of Material Structure Science, High Energy Accelerator Research Organization (KEK), Tsukuba 305-0801 (Japan); Yoshida, N. [Institute for Applied Mechanics, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan)

2010-03-15

Ultra-fine grained (UFG) W-TiC compacts fabricated by powder metallurgical methods utilizing mechanical alloying (MA) are very promising for use in irradiation environments. However, the assurance of room-temperature ductility and enhancement in surface resistances to low-energy hydrogen irradiation are unsettled issues. As an approach to solution to these, microstructural modification by hot plastic working has been applied to UFG W-TiC processed by MA in a purified Ar or H{sub 2} atmosphere and hot isostatic pressing (HIP). Hot plastically worked compacts have been subjected to 3-point bend tests at room temperature and TEM microstructural examinations. It is found that the microstructural modification allows us to convert UFG W-1.1%TiC to compacts exhibiting a very high fracture strength and appreciable ductility at room temperature. The compacts of W-1.1%TiC/Ar (MA atmosphere: Ar) and W-1.1%TiC/H{sub 2} (MA atmosphere: H{sub 2}) exhibit re-crystallized structures with approximately 0.5 and 1.5 mum in grain size, respectively. It is shown that the enhancement of fracture resistance by microstructural modifications is attributed to significant strengthening of weak grain boundaries in the re-crystallized state. As a result the modified compacts exhibit superior surface resistance to low-energy deuteron irradiation.

Au@TiO2 yolk-shell nanostructures for enhanced performance in both photoelectric and photocatalytic solar conversion

Science.gov (United States)

He, Qinrong; Sun, Hang; Shang, Yinxing; Tang, Yanan; She, Ping; Zeng, Shan; Xu, Kongliang; Lu, Guolong; Liang, Song; Yin, Shengyan; Liu, Zhenning

2018-05-01

Solar energy conversion is an important field gaining increasing interest. Herein, bio-inspired Au@TiO2 yolk-shell nanoparticles (NPs) have been prepared via a facial one-pot hydrothermal approach. The Au@TiO2 yolk-shell NPs can self-assemble into 3D-structure to form photoelectrode for photoelectric conversion. The obtained photoelectrode demonstrates a swift and stable photocurrent of 3.5 μA/cm2, which is 4.2 and 1.6 times higher than those of the photocurrents generated by the counterparts of commercial TiO2 and Au@TiO2 core-shell NPs, respectively. Moreover, compared to the commercial TiO2 and Au@TiO2 core-shell NPs, the Au@TiO2 yolk-shell NPs also exhibit superior photocatalytic activity, delivering a H2 evolution rate of 4.92 mmol/g h. The performance improvement observed for the Au@TiO2 yolk-shell NPs is likely contributed by two synergistic factors, i.e. the incorporation of AuNPs and the unique hollow structure, which benefit the activity by simultaneously enhancing light utilization, charge separation and reaction site accessibility. The rational design and fabrication of Au@TiO2 yolk-shell NPs hold great promise for future application in efficient solar energy conversion.

Facile synthesis of CdS@TiO2 core–shell nanorods with controllable shell thickness and enhanced photocatalytic activity under visible light irradiation

International Nuclear Information System (INIS)

Dong, Wenhao; Pan, Feng; Xu, Leilei; Zheng, Minrui; Sow, Chorng Haur; Wu, Kai; Xu, Guo Qin

2015-01-01

Graphical abstract: - Highlights: • CdS nanorods were coated with amorphous TiO 2 shells under a mild condition. • The TiO 2 shell thickness can be controlled from 3.5 to 40 nm. • CdS@TiO 2 nanorods exhibit enhanced photocatalytic activities under visible light. • Efficient charge carriers separation leads to the improved photocatalytic activity. - Abstract: Amorphous TiO 2 layers with a controllable thickness from 3.5 to 40 nm were coated on the one-dimensional CdS nanorods surface under mild conditions. Compared to the bare CdS nanorods, the as-prepared CdS@TiO 2 nanorods exhibit enhanced photocatalytic activities for phenol photodecomposition under visible light irradiation. The improved photoactivity is ascribed to the efficient separation of photogenerated electron and hole charge carriers between CdS cores and TiO 2 shells. This study promises a simple approach to fabricating CdS@TiO 2 core–shell structure nanocomposites, and can be applied for other semiconductor cores with TiO 2 shells

Enhancement of photocurrents due to the oxidation of water and organic compounds at BiZn2VO6 particulate thin film electrodes by treatment with a TiCl4 solution

International Nuclear Information System (INIS)

Liu Haimei; Imanishi, Akihito; Yang Wensheng; Nakato, Yoshihiro

2010-01-01

Photocurrents due to water oxidation at BiZn 2 VO 6 (E g 2.4 eV) particulate thin film electrodes were largely enhanced by pre-treatment with an aqueous TiCl 4 solution. Photocurrents for BiZn 2 VO 6 electrodes with no TiCl 4 treatment were also enhanced by the addition of organic compounds such as methanol and trimethyl amine to the aqueous electrolyte. Interestingly, such enhanced photocurrents by organic compounds were further enhanced by the TiCl 4 pre-treatment. EDAX and SEM investigations showed the formation of a flock-like TiO 2 overlayer on BiZn 2 VO 6 particles after the TiCl 4 treatment. The photocurrent enhancement by the TiCl 4 pre-treatment is thus mainly attributed to the necking effect of the flock-like TiO 2 overlayer, which facilitates the transport of photogenerated electrons within the BiZn 2 VO 6 particulate thin film electrode.

Interfacial Nb-substitution induced anomalous enhancement of polarization and conductivity in BaTiO3 ferroelectric tunnel junctions

Directory of Open Access Journals (Sweden)

H. F. Li

2014-12-01

Full Text Available Using density functional theory (DFT method combined with non-equilibrium Green’s function approach, we systematically investigated the structural, ferroelectric and electronic transport properties of Pt/BaTiO3/Pt ferroelectric tunnel junctions (FTJ with the interface atomic layers doped by charge neutral NbTi substitution. It is found that interfacial NbTi substitution will produce several anomalous effects such as the vanishing of ferroelectric critical thickness and the decrease of junction resistance against tunneling current. Consequently, the thickness of the ferroelectric thin film (FTF in the FTJ can be reduced, and both the electroresistance effect and sensitivity to external bias of the FTJ are enhanced. Our calculations indicate that the enhancements of conductivity and ferroelectric distortion can coexist in FTJs, which should be important for applications of functional electronic devices based on FTJs.

Synthesis and enhanced electrochemical performance of the honeycomb TiO2/LiMn2O4 cathode materials

DEFF Research Database (Denmark)

Zhang, J.Y.; Shen, J.X.; Wei, C.B.

2016-01-01

angle compare to LiMn2O4, implying that TiO2 doping induced a change of crystal structure. By performing electrochemical measurements, we observed an enhancement of specific capacity (127.28 mAhg−1) and an improvement of cycling stability in the TiO2/LiMn2O4 hybrid materials. After 100 cycles of charge...

Synergistic effect of surface self-doping and Fe species-grafting for enhanced photocatalytic activity of TiO{sub 2} under visible-light

Energy Technology Data Exchange (ETDEWEB)

Kong, Lina [Center for Advanced Optoelectronic Functional Materials Research, Key Laboratory of UV-Emitting Materials and Technology of Ministry of Education, Northeast Normal University, 5268 Renmin Street, Changchun 130024 (China); Institute of Material Physics, Key Laboratory of Display Materials and Photoelectric Devices of Ministry of Education, Tianjin University of Technology, Tianjin 300384 (China); Wang, Changhua; Wan, Fangxu; Zheng, Han [Center for Advanced Optoelectronic Functional Materials Research, Key Laboratory of UV-Emitting Materials and Technology of Ministry of Education, Northeast Normal University, 5268 Renmin Street, Changchun 130024 (China); Zhang, Xintong, E-mail: xtzhang@nenu.edu.cn [Center for Advanced Optoelectronic Functional Materials Research, Key Laboratory of UV-Emitting Materials and Technology of Ministry of Education, Northeast Normal University, 5268 Renmin Street, Changchun 130024 (China)

2017-02-28

Highlights: • Anatase TiO{sub 2} was modified with Fe-ethoxide through wet impregnation method. • XPS and EPR investigation supported the formation of Vo and Fe species. • Vo improved the optical absorption properties to a larger extent. • Fe species inhibited the charge carrier recombination process. • Synergism between Vo and Fe species enhanced the photocatalytic activity. - Abstract: Surface grafting of transition-metal complexes or oxides is an appealing way to enhance the photocatalytic activity of TiO{sub 2} under visible-light excitation. However, the performance of these co-catalysts assistant TiO{sub 2} photocatalysts is still not sufficient enough due to their relatively weak visible-light absorption. Herein, we report a simple impregnation treatment with ferric ethoxide/ethanol solvent, followed with mild heating which can significantly enhance the visible-light absorption and photocatalytic activity of TiO{sub 2}. XPS and EPR analyses manifest that the oxygen vacancies (V{sub O}s) and Fe-species are simultaneously introduced to the surface of TiO{sub 2}. The chemical state and photocatalytic activity of the Fe-species-grafted TiO{sub 2−x} is dependent on the heating temperature after impregnation. The sample heat-treated at 250 °C exhibits the optimal photocatalytic performance for β-naphthol degradation with rate constant 6.0, 2.7, and 3.9 times higher than that of TiO{sub 2}, TiO{sub 2−x}, and Fe-TiO{sub 2}, respectively. The activity enhancement is discussed on the basis of the synergistic effect and energy-level matching of surface V{sub O}s and Fe-species co-catalyst, i.e. the V{sub O}s defects states increase the visible-light absorption and the Fe-species in the form of FeOOH promote the consumption of photo-generated electrons through multi-electron reduction of adsorbed molecule oxygen.

Core–shell TiO2 microsphere with enhanced photocatalytic activity and improved lithium storage

International Nuclear Information System (INIS)

Guo, Hong; Tian, Dongxue; Liu, Lixiang; Wang, Yapeng; Guo, Yuan; Yang, Xiangjun

2013-01-01

Inorganic hollow core–shell spheres have attracted considerable interest due to their singular properties and wide range of potential applications. Herein a novel facile generic strategy of combining template assisted and solvothermal alcoholysis is employed to prepare core–void–shell anatase TiO 2 nanoparticle aggregates with an excellent photocatalytic activity, and enhanced lithium storage in large quantities. Amorphous carbon can be loaded on the TiO 2 nanoparticles uniformly under a suitably formulated ethanol/water system in the solvothermal alcoholysis process, and the subsequent calcination results of the formation of core–shell–shell anatase TiO 2 nanoparticle aggregates. The intrinsic core–void–shell nature as well as high porosity of the unique nanostructures contributes greatly to the superior photocatalytic activity and improved performance as anode materials for lithium ion batteries. - Graphical abstract: A novel strategy of combining template assisted and solvothermal alcoholysis is employed to prepare unique core–void–shell anatase TiO 2 nanoparticle aggregates with the superior photocatalytic activity and improved lithium storage. Highlights: ► TiO 2 mesospheres are synthesized by solvothermal alcoholysis. ► It is core–void–shell structure and the thickness of shell is estimated to 80 nm. ► It exhibits a remarkable photocatalytic activity and improved lithium storage

Fabrication of doped TiO2 nanotube array films with enhanced photo-catalytic activity

Science.gov (United States)

Peighambardoust, Naeimeh-Sadat; Khameneh-asl, Shahin; Khademi, Adib

2018-01-01

In the present work, we investigate the N and Fe-doped TiO2 nanotube array film prepared by treating TiO2 nanotube array film with ammonia solution and anodizing in Fe(NO3)3 solution respectively. This method avoided the use of hazardous ammonia gas, or laborious ion implantation process. N and Fe-doped TiO2 nanotube arrays (TiO2 NTs) were prepared by electrochemical anodization process in 0.5 wt % HF aqueous solution. The anodization was performed at the conditions of 20 V and 20 min, Followed by a wet immersion in NH3.H2O (1M) for N-doping for 2 hr and annealing post-treatment at 450 °C. The morphology and structure of the nanotube films were characterized by field emission scanning electron microscope (FESEM) and EDX. UV-vis. illumination test were done to observe photo-enhanced catalysis. The effect of different annealing temperature on the structure and photo-absorption property of the TiO2-TNTs was investigated. The results showed that N-TNTs nanotubes exhibited higher photocatalytic activity compared whit the Fe-doped and pure TNTs, because doping N promoted the separation of the photogenerated electrons and holes.

Amorphous and crystalline TiO2 nanotube arrays for enhanced Li-ion intercalation properties.

Science.gov (United States)

Guan, Dongsheng; Cai, Chuan; Wang, Ying

2011-04-01

We have employed a simple process of anodizing Ti foils to prepare TiO2 nanotube arrays which show enhanced electrochemical properties for applications as Li-ion battery electrode materials. The lengths and pore diameters of TiO2 nanotubes can be finely tuned by varying voltage, electrolyte composition, or anodization time. The as-prepared nanotubes are amorphous and can be converted into anatase nanotubes with heat treatment at 480 degrees C. Rutile crystallites emerge in the anatase nanotube when the annealing temperature is increased to 580 degrees C, resulting in TiO2 nanotubes of mixed phases. The morphological features of nanotubes remain unchanged after annealing. Li-ion insertion performance has been studied for amorphous and crystalline TiO2 nanotube arrays. Amorphous nanotubes with a length of 3.0 microm and an outer diameter of 125 nm deliver a capacity of 91.2 microA h cm(-2) at a current density of 400 microA cm(-2), while those with a length of 25 microm and an outer diameter of 158 nm display a capacity of 533 microA h cm-2. When the 3-microm long nanotubes become crystalline, they deliver lower capacities: the anatase nanotubes and nanotubes of mixed phases show capacities of 53.8 microA h cm-2 and 63.1 microA h cm(-2), respectively at the same current density. The amorphous nanotubes show excellent capacity retention ability over 50 cycles. The cycled nanotubes show little change in morphology compared to the nanotubes before electrochemical cycling. All the TiO2 nanotubes demonstrate higher capacities than amorphous TiO2 compact layer reported in literature. The amorphous TiO2 nanotubes with a length of 1.9 microm exhibit a capacity five times higher than that of TiO2 compact layer even when the nanotube array is cycled at a current density 80 times higher than that for the compact layer. These results suggest that anodic TiO2 nanotube arrays are promising electrode materials for rechargeable Li-ion batteries.

Solvothermal syntheses of Bi and Zn co-doped TiO_2 with enhanced electron-hole separation and efficient photodegradation of gaseous toluene under visible-light

International Nuclear Information System (INIS)

Li, Juan-Juan; Cai, Song-Cai; Xu, Zhen; Chen, Xi; Chen, Jin; Jia, Hong-Peng; Chen, Jing

2017-01-01

Highlights: • Bi-Zn co-doped TiO_2 catalysts were prepared by solvothermal route. • The incorporation of Bi doping into the TiO_2 generates intermediate energy levels. • Bi and Zn doping showed the enhanced absorption in visible-light region. • Zn dopant acts as a mediator of interfacial charge transfer. • TiBi_1_._9_%Zn_1_%O_2 exhibited high photocatalytic degradation for toluene. - Abstract: This study investigated the effects of Bi doped and Bi-Zn co-doped TiO_2 on photodegradation of gaseous toluene. The doped TiO_2 with various concentration of metal was prepared using the solvothermal route and characterized by SEM, XRD, Raman, BET, DRS, XPS, PL and EPR. Their photocatalytic activities under visible-light irradiation were drastically influenced by the dopant content. The results showed that moderate metal doping levels were obviously beneficial for the toluene degradation, while high doping levels suppressed the photocatalytic activity. The photocatalytic degradation of toluene over TiBi_1_._9_%O_2 and TiBi_1_._9_%Zn_1_%O_2 can reach to 51% and 93%, respectively, which are much higher than 25% of TiO_2. Bi doping into TiO_2 lattice generates new intermediate energy level of Bi below the CB edge of TiO_2. The electron excitation from the VB to Bi orbitals results in the decreased band gap, extended absorption of visible-light and thus enhances its photocatalytic efficiency. Zn doping not only further enhances the absorption in this visible-light region, but also Zn dopant exists as the form of ZnO crystallites located on the interfaces of TiO_2 agglomerates and acts as a mediator of interfacial charge transfer to suppress the electron-hole recombination. These synergistic effects are responsible for the enhanced photocatalytic performance.

Usefulness of combined use of contrast-enhanced ultrasound and TI-RADS classification for the differentiation of benign from malignant lesions of thyroid nodules.

Science.gov (United States)

Zhang, Yan; Zhou, Ping; Tian, Shuang-Ming; Zhao, Yong-Feng; Li, Jia-Le; Li, Lan

2017-04-01

To study the thyroid image reporting and data system (TI-RADS) classification and the contrast-enhanced ultrasound (CEUS) enhancement pattern of thyroid nodules, and to determine whether combined use of both methods is helpful in the diagnosis of thyroid nodules. A total of 319 thyroid nodules in 246 patients were assessed with TI-RADS, CEUS and a combination of both methods. The diagnostic performance of TI-RADS, CEUS and a combination of both methods was compared. The accuracy in the diagnosis of thyroid nodules was 90.3 % for TI-RADS, 90.0 % for CEUS and 96.0 % for a combination of both methods respectively. A statistically significant difference was not observed in the diagnostic accuracy of CEUS and TI-RADS (P > 0.05). However, a significant difference was observed between a combination of both methods and either alone (P TI-RADS classifications of 4a and 4b thyroid nodules compared with TI-RADS alone (P  0.05). The improved TI-RADS, when combined with CEUS, could significantly improve the diagnostic accuracy for thyroid nodules, especially for TI-RADS class-4 thyroid nodules. • TI-RADS can be used as the primary diagnostic standard for thyroid nodules • CEUS can be used as an important complement to TI-RADS • The improved TI-RADS can significantly improve the qualitative diagnostic accuracy.

Fabrication of uniformly dispersed Ag nanoparticles loaded TiO{sub 2} nanotube arrays for enhancing photoelectrochemical and photocatalytic performances under visible light irradiation

Energy Technology Data Exchange (ETDEWEB)

Yi, Junhui; Zhang, Shengsen; Wang, Hongjuan; Yu, Hao; Peng, Feng, E-mail: cefpeng@scut.edu.cn

2014-12-15

Graphical abstract: Uniformly dispersed Ag nanoparticles (NPs) were successfully loaded on both the outer and inner surface of the TiO{sub 2} nanotube arrays (NTs) through a simple polyol method, which exhibited the enhanced photoelectrochemical and photocatalytic performances under visible-light irradiation due to the more effective separation of photo-generated electron–hole pairs and faster interfacial charge transfer. - Highlights: • Highly dispersed Ag nanoparticles (NPs) are successfully prepared by polyol method. • Ag NPs are uniformly loaded on the surface of the TiO{sub 2} nanotube arrays (NTs). • Ag/TiO{sub 2}-NTs exhibit the enhanced photocatalytic activity under visible-light. • The enhanced photocurrent is explained by electrochemical impedance spectroscopy. - Abstract: Uniformly dispersed Ag nanoparticles (NPs) were successfully loaded on both the outer and inner surface of the TiO{sub 2} nanotube arrays (NTs) through a simple polyol method. The as-prepared Ag/TiO{sub 2}-NTs were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and UV–vis diffusion reflectance spectroscopy. Photoelectrochemical behaviors were investigated via photocurrent response and electrochemical impedance spectroscopy (EIS). Photocatalytic activity of Ag/TiO{sub 2}-NTs was evaluated by degradation of acid orange II under visible light irradiation. The results showed that photocatalytic efficiency of Ag/TiO{sub 2}-NTs is more than 5 times higher than that of pure TiO{sub 2} NTs. Comparing with the electrochemical deposition method, the photocatalytic activity of Ag/TiO{sub 2}-NTs prepared by polyol method has been obviously increased.

From Quality Assurance to Quality Enhancement in the European Higher Education Area

Science.gov (United States)

Gvaramadze, Irakli

2008-01-01

This article focuses on recent trends in quality assurance initiatives, analyses how the European Higher Education Area promotes quality enhancement mechanisms and their implications for quality cultures in universities. It presents and discusses two approaches towards quality enhancement both at the institutional and programme level: 1. Quality…

Enhanced TiO2 Photocatalytic Processing of Organic Wastes for Green Space Exploration

Science.gov (United States)

Udom, I.; Goswami, D. Y.; Ram, M. K.; Stefanakos, E. K.; Heep, A. F.; Kulis, M. J.; McNatt, J. S.; Jaworske, D. A.; Jones, C. A.

2013-01-01

The effect of transition metal co-catalysts on the photocatalytic properties of TiO2 was investigated. Ruthenium (Ru), palladium, platinum, copper, silver, and gold, were loaded onto TiO2 powders (anatase and mixed-phase P25) and screened for the decomposition of rhodamine B (RhB) under broad-band irradiation. The morphology and estimated chemical composition of photocatalysts were determined by scanning electron microscopy and energy dispersive spectroscopy, respectively. Brunhauer, Emmett and Teller (BET) analysis measured mass-specific surface area(s). X-ray diffraction analysis was performed to confirm the identity of titania phase(s) present. The BET surface area of anatase TiO2/Ru 1% (9.2 sq m/gm) was one of the highest measured of all photocatalysts prepared in our laboratory. Photolyses conducted under air-saturated and nitrogen-saturated conditions revealed photodegradation efficiencies of 85 and 2 percent, respectively, after 60 min compared to 58 percent with no catalyst. The cause of low photocatalytic activity under an inert atmosphere is discussed. TiO2/Ru 1% showed a superior photocatalytic activity relative to P25-TiO2 under broad-band irradiation. A potential deployment of photocatalytic technologies on a mission could be a reactor with modest enhancement in solar intensity brought about by a trough-style reactor, with reactants and catalyst flowing along the axis of the trough and therefore being illuminated for a controlled duration based on the flow rate.

Course Evaluation Systems for Open-ended Quality Enhancement

DEFF Research Database (Denmark)

Piihl, Jesper; Rasmussen, Jens Smed

2013-01-01

Quality in higher education is widely controlled through surveys asking students to evaluate teaching. However, control of quality does not necessarily lead to enhancement of quality. Drawing on accounting research and a case study, a measurement-based and open-ended quality control system...... emphasising quality enhancement is suggested. The case shows how interactive use of performance measurement can lead to more engaged and enabling dialogue amongst involved actors concerning quality enhancement, however institutionalised beliefs regarding course evaluation systems makes a change challenging....... The chapter suggests that open-ended measurement systems enabling stakeholders to take responsibility for quality enhancement is not so much a matter of technical design as a matter of an enabling style of use....

Enhanced visible-light photocatalytic activity for selective oxidation of amines into imines over TiO{sub 2}(B)/anatase mixed-phase nanowires

Energy Technology Data Exchange (ETDEWEB)

Dai, Jun [Institute of Applied Chemistry, Henan Polytechnic University, Jiaozuo 454003 (China); State Key Laboratory Cultivation Base for Gas Geology and Gas Control, School of Safety Science and Engineering, Henan Polytechnic University, Jiaozuo 454003 (China); Yang, Juan, E-mail: yangjuanhpu@yahoo.com [Institute of Applied Chemistry, Henan Polytechnic University, Jiaozuo 454003 (China); Wang, Xiaohan; Zhang, Lei; Li, Yingjie [Institute of Applied Chemistry, Henan Polytechnic University, Jiaozuo 454003 (China)

2015-09-15

Graphical abstract: Visible-light photocatalytic activities for selective oxidation of amines into imines are greatly affected by the crystal structure of TiO{sub 2} catalysts and mixed-phase TiO{sub 2}(B)/anatase possess higher photoactivity because of the moderate adsorption ability and efficient charge separation. - Highlights: • Visible-light photocatalytic oxidation of amines to imines is studied over different TiO{sub 2}. • Photocatalytic activities are greatly affected by the crystal structure of TiO{sub 2} nanowires. • Mixed-phase TiO{sub 2}(B)/anatase exhibits higher catalytic activity than single-phase TiO{sub 2}. • Enhanced activity is ascribed to efficient adsorption ability and interfacial charge separation. • Photoinduced charge transfer mechanism on TiO{sub 2}(B)/anatase catalysts is also proposed. - Abstract: Wirelike catalysts of mixed-phase TiO{sub 2}(B)/anatase TiO{sub 2}, bare anatase TiO{sub 2} and TiO{sub 2}(B) are synthesized via calcining precursor hydrogen titanate obtained from hydrothermal process at different temperatures between 450 and 700 °C. Under visible light irradiation, mixed-phase TiO{sub 2}(B)/anatase TiO{sub 2} catalysts exhibit enhanced photocatalytic activity in comparison with pure TiO{sub 2}(B) and anatase TiO{sub 2} toward selective oxidation of benzylamines into imines and the highest photocatalytic activity is achieved by TW-550 sample consisting of 65% TiO{sub 2}(B) and 35% anatase. The difference in photocatalytic activities of TiO{sub 2} samples can be attributed to the different adsorption abilities resulted from their crystal structures and interfacial charge separation driven by surface-phase junctions between TiO{sub 2}(B) and anatase TiO{sub 2}. Moreover, the photoinduced charge transfer mechanism of surface complex is also proposed over mixed-phase TiO{sub 2}(B)/anatase TiO{sub 2} catalysts. Advantages of this photocatalytic system include efficient utilization of solar light, general suitability to

Ti-doped hydrogenated diamond like carbon coating deposited by hybrid physical vapor deposition and plasma enhanced chemical vapor deposition

Science.gov (United States)

Lee, Na Rae; Sle Jun, Yee; Moon, Kyoung Il; Sunyong Lee, Caroline

2017-03-01

Diamond-like carbon films containing titanium and hydrogen (Ti-doped DLC:H) were synthesized using a hybrid technique based on physical vapor deposition (PVD) and plasma enhanced chemical vapor deposition (PECVD). The film was deposited under a mixture of argon (Ar) and acetylene gas (C2H2). The amount of Ti in the Ti-doped DLC:H film was controlled by varying the DC power of the Ti sputtering target ranging from 0 to 240 W. The composition, microstructure, mechanical and chemical properties of Ti-doped DLC:H films with varying Ti concentrations, were investigated using Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), nano indentation, a ball-on-disk tribometer, a four-point probe system and dynamic anodic testing. As a result, the optimum composition of Ti in Ti-doped DLC:H film using our hybrid method was found to be a Ti content of 18 at. %, having superior electrical conductivity and high corrosion resistance, suitable for bipolar plates. Its hardness value was measured to be 25.6 GPa with a low friction factor.

Hierarchical Honeycomb Br-, N-Codoped TiO2 with Enhanced Visible-Light Photocatalytic H2 Production.

Science.gov (United States)

Zhang, Chao; Zhou, Yuming; Bao, Jiehua; Sheng, Xiaoli; Fang, Jiasheng; Zhao, Shuo; Zhang, Yiwei; Chen, Wenxia

2018-06-06

The halogen elements modification strategy of TiO 2 encounters a bottleneck in visible-light H 2 production. Herein, we have for the first time reported a hierarchical honeycomb Br-, N-codoped anatase TiO 2 catalyst (HM-Br,N/TiO 2 ) with enhanced visible-light photocatalytic H 2 production. During the synthesizing process, large amounts of meso-macroporous channels and TiO 2 nanosheets were fabricated in massive TiO 2 automatically, constructing the hierarchical honeycomb structure with large specific surface area (464 m 2 g -1 ). cetyl trimethylammonium bromide and melamine played a key role in constructing the meso-macroporous channels. Additionally, HM-Br,N/TiO 2 showed a high visible-light H 2 production rate of 2247 μmol h -1 g -1 , which is far more higher than single Br- or N-doped TiO 2 (0 or 63 μmol h -1 g -1 , respectively), thereby demonstrating the excellent synergistic effects of Br and N elements in H 2 evolution. In HM-Br,N/TiO 2 catalytic system, the codoped Br-N atoms could reduce the band gap of TiO 2 to 2.88 eV and the holes on acceptor levels (N acceptor) can passivate the electrons on donor levels (Br donor), thereby preventing charge carriers recombination significantly. Furthermore, the proposed HM-Br,N/TiO 2 fabrication strategy had a wide range of choices for N source (e.g., melamine, urea, and dicyandiamide) and it can be applied to other TiO 2 materials (e.g., P25) as well, thereby implying its great potential application in visible-light H 2 production. Finally, on the basis of experimental results, a possible photocatalytic H 2 production mechanism for HM-Br,N/TiO 2 was proposed.

Characterization and mechanism analysis of N doped TiO2 with visible light response and its enhanced visible activity

International Nuclear Information System (INIS)

Cheng Xiuwen; Yu Xiujuan; Xing Zipeng

2012-01-01

Nitrogen doped TiO 2 nanoparticles were synthesized through a hydrolysis-precipitation process using ammonia water as the doping species. The resulting materials were characterized by XRD, DRS, SPS, XPS and FT-IR. Further, the activity enhanced-mechanism was discussed in detail. XRD results showed that doping with nitrogen could effectively retard the phase transformation of TiO 2 from anatase to rutile and increase the anatase crystallinity. DRS and SPS results indicated that the light absorbance edge of nitrogen doped TiO 2 nanoparticle was obviously red-shifted to visible light region and the separation rates of photogenerated charge carriers were greatly improved, respectively. XPS and FT-IR analysis implied that the contents of surface hydroxyl groups were improved significantly and the VBM (valance bond maximum) of O2p was 2.3 eV. Under the visible light irradiation with 120 min, a 65.3% degradation rate of phenol could be achieved. The photocatalytic activity of nitrogen doped TiO 2 was 2.08 and 1.97 times than that of pure TiO 2 and P25 TiO 2 , respectively. The enhanced visible light activity was attributed to the well anatase crystallinity, small crystallite size, intense light absorbance edge in visible region, more content of surface hydroxyl groups and high separation efficiency of photogenerated charge carriers.

Fabrication of BiOBr nanosheets@TiO{sub 2} nanobelts p–n junction photocatalysts for enhanced visible-light activity

Energy Technology Data Exchange (ETDEWEB)

Zhao, Yang [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Huang, Xiang [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); School of Science, Tibet University, Lhasa 850000 (China); Tan, Xin [School of Science, Tibet University, Lhasa 850000 (China); Yu, Tao, E-mail: yutao@tju.edu.cn [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Collaborative Innovation Center of Chemical Science and Engineering (Tianjin), Tianjin 300072 (China); Li, Xiangli [School of Environmental Science and Engineering, Tianjin University, Tianjin 300072 (China); Yang, Libin [College of Chemical Engineering and Materials Science, Tianjin University of Science & Technology, Tianjin Key Laboratory of Marine Resources and Chemistry, Tianjin 300457 (China); Wang, Shucong [School of Environmental Science and Engineering, Tianjin University, Tianjin 300072 (China)

2016-03-01

Graphical abstract: - Highlights: • BiOBr nanosheets@TiO{sub 2} nanobelts p–n junction photocatalysts have been synthesized. • The p–n junction photocatalysts improved water splitting and dye degradation activity. • BiOBr amount in the BiOBr@TiO{sub 2} photocatalysts was investigated. - Abstract: The construction of p–n junction structure is a smart strategy for improving the photocatalytic activity, since p–n junctions can inhibit the recombination of photo-induced charges. Herein, BiOBr nanosheets@TiO{sub 2} nanobelts p–n junction photocatalysts were prepared by assembling BiOBr nanosheets on the surface of TiO{sub 2} nanobelts via a hydrothermal route followed by a co-precipitation process. BiOBr@TiO{sub 2} p–n junction photocatalysts exhibited enhanced photocatalytic activity in photocatalytic H{sub 2} production over water splitting and photodegradation of Rhodamine B (RhB) under visible light irradiation. Mott–Schottky plots confirmed the formation of p–n junctions in the interface of BiOBr and TiO{sub 2}. The enhanced photocatalytic performance can be ascribed to the 1D nanostructure and the formation of p–n junctions. This work shows a potential application of low cost BiOBr as a substitute for noble metals in photocatalytic H{sub 2} production under visible light irradiation.

Copper doping enhanced the oxidative stress-mediated cytotoxicity of TiO2 nanoparticles in A549 cells.

Science.gov (United States)

Ahmad, J; Siddiqui, M A; Akhtar, M J; Alhadlaq, H A; Alshamsan, A; Khan, S T; Wahab, R; Al-Khedhairy, A A; Al-Salim, A; Musarrat, J; Saquib, Q; Fareed, M; Ahamed, M

2018-05-01

Physicochemical properties of titanium dioxide nanoparticles (TiO 2 NPs) can be tuned by doping with metals or nonmetals. Copper (Cu) doping improved the photocatalytic behavior of TiO 2 NPs that can be applied in various fields such as environmental remediation and nanomedicine. However, interaction of Cu-doped TiO 2 NPs with human cells is scarce. This study was designed to explore the role of Cu doping in cytotoxic response of TiO 2 NPs in human lung epithelial (A549) cells. Characterization data demonstrated the presence of both TiO 2 and Cu in Cu-doped TiO 2 NPs with high-quality lattice fringes without any distortion. The size of Cu-doped TiO 2 NPs (24 nm) was lower than pure TiO 2 NPs (30 nm). Biological results showed that both pure and Cu-doped TiO 2 NPs induced cytotoxicity and oxidative stress in a dose-dependent manner. Low mitochondrial membrane potential and higher caspase-3 enzyme (apoptotic markers) activity were also observed in A549 cells exposed to pure and Cu-doped TiO 2 NPs. We further observed that cytotoxicity caused by Cu-doped TiO 2 NPs was higher than pure TiO 2 NPs. Moreover, antioxidant N-acetyl cysteine effectively prevented the reactive oxygen species generation, glutathione depletion, and cell viability reduction caused by Cu-doped TiO 2 NPs. This is the first report showing that Cu-doped TiO 2 NPs induced cytotoxicity and oxidative stress in A549 cells. This study warranted further research to explore the role of Cu doping in toxicity mechanisms of TiO 2 NPs.

A Cost-Effective Solid-State Approach to Synthesize g-C3N4 Coated TiO2 Nanocomposites with Enhanced Visible Light Photocatalytic Activity

Directory of Open Access Journals (Sweden)

Min Fu

2013-01-01

Full Text Available Novel graphitic carbon nitride (g-C3N4 coated TiO2 nanocomposites were prepared by a facile and cost-effective solid-state method by thermal treatment of the mixture of urea and commercial TiO2. Because the C3N4 was dispersed and coated on the TiO2 nanoparticles, the as-prepared g-C3N4/TiO2 nanocomposites showed enhanced absorption and photocatalytic properties in visible light region. The as-prepared g-C3N4 coated TiO2 nanocomposites under 450°C exhibited efficient visible light photocatalytic activity for degradation of aqueous MB due to the increased visible light absorption and enhanced MB adsorption. The g-C3N4 coated TiO2 nanocomposites would have wide applications in both environmental remediation and solar energy conversion.

Enhanced separation efficiency of photoinduced charges for antimony-doped tin oxide (Sb-SnO{sub 2})/TiO{sub 2} heterojunction semiconductors with varied Sb doping concentration

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhen-Long [School of Physics and Electronics, Henan University, Kaifeng 475004 (China); Ma, Wen-Hai [School of Physical Education, Henan University, Kaifeng 475004 (China); Mao, Yan-Li, E-mail: ylmao1@163.com [School of Physics and Electronics, Henan University, Kaifeng 475004 (China); Institute for Computational Materials Science, Henan University, Kaifeng 475004 (China)

2014-09-07

In this paper, antimony-doped tin oxide (Sb-SnO{sub 2}) nanoparticles were synthesized with varied Sb doping concentration, and the Sb-SnO{sub 2}/TiO{sub 2} heterojunction semiconductors were prepared with Sb-SnO{sub 2} and TiO{sub 2}. The separation efficiency of photoinduced charges was characterized with surface photovoltage (SPV) technique. Compared with Sb-SnO{sub 2} and TiO{sub 2}, Sb-SnO{sub 2}/TiO{sub 2} presents an enhanced separation efficiency of photoinduced charges, and the SPV enhancements were estimated to be 1.40, 1.43, and 1.99 for Sb-SnO{sub 2}/TiO{sub 2} composed of Sb-SnO{sub 2} with the Sb doping concentration of 5%, 10%, and 15%, respectively. To understand the enhancement, the band structure of Sb-SnO{sub 2} and TiO{sub 2} in the heterojunction semiconductor was determined, and the conduction band offsets (CBO) between Sb-SnO{sub 2} and TiO{sub 2} were estimated to be 0.56, 0.64, and 0.98 eV for Sb-SnO{sub 2}/TiO{sub 2} composed of Sb-SnO{sub 2} with the Sb doping concentration of 5%, 10%, and 15%, respectively. These results indicate that the separation efficiency enhancement is resulting from the energy level matching, and the increase of enhancement is due to the rising of CBO.

Visible-light wavelength matched microsphere assembly of TiO{sub 2} superfine nanorods and the enhanced photovoltaic performance

Energy Technology Data Exchange (ETDEWEB)

Tao, Xiyun; Wang, Yumin; Zhang, Xiang; Sun, Hongxia; Zhang, Qingsong; Niu, Laiyou; Liu, Juan; Zhou, Xingfu, E-mail: Zhouxf@njtech.edu.cn

2015-05-15

Graphical abstract: A novel visible-light wavelength matched microspheres assembly of TiO{sub 2} superfine nanorods with a diameter of ∼5 nm was fabricated via a hydrothermal method. The as-prepared rutile TiO{sub 2} microspheres have a uniform diameter of ∼450 nm and show a good light-trapping performance. Dye-sensitized solar cell based on this sample shows a satisfactory energy conversion efficiency of 6.59% and is the highest PCE reported for intrinsic rutile TiO{sub 2}. The further optimized DSSC shows a conversion efficiency of 8.3%, though the internal resistance is higher and the dye absorption is lower than that of widely used anatase TiO{sub 2} nanoparticles. - Highlights: • Microsphere assembly of TiO{sub 2} nanorods with a diameter of ∼5 nm was fabricated. • TiO{sub 2} microspheres size is well matched with the visible light wavelength. • TiO{sub 2} microsphere enhances the light-scattering ability. • Rutile TiO{sub 2} microsphere shows an energy conversion efficiency of 6.59%. • The highest PCE reported for intrinsic rutile TiO{sub 2} is obtained. - Abstract: According to the Mie scattering theory, spheres with the size matched with light wavelength are most suitable for light scattering and enhance the light trapping ability. In this paper, a novel visible-light wavelength matched sphere assembly of TiO{sub 2} superfine nanorods was fabricated via a simple one-step hydrothermal method. The morphology and the structure were examined by field emission scanning electron microscopy (FESEM), X-ray powder diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). The visible subwavelength TiO{sub 2} microsphere resembling an immature chinese chestnut is composed of countless superfine TiO{sub 2} nanorods, the diameter of these building blocks of superfine TiO{sub 2} nanorods is ∼5 nm. The obtained TiO{sub 2} sphere has an average diameter of ca. 450 nm, which matches well with the visible light wavelength and cause the

Enhanced performance of inverted organic photovoltaic cells using CNTs-TiO(X) nanocomposites as electron injection layer.

Science.gov (United States)

Zhang, Hong; Xu, Meifeng; Cui, Rongli; Guo, Xihong; Yang, Shangyuan; Liao, Liangsheng; Jia, Quanjie; Chen, Yu; Dong, Jinquan; Sun, Baoyun

2013-09-06

In this study, we fabricated inverted organic photovoltaic cells with the structure ITO/carbon nanotubes (CNTs)-TiO(X)/P3HT:PCBM/MoO₃/Al by spin casting CNTs-TiO(X) nanocomposite (CNTs-TiO(X)) as the electron injection layer onto ITO/glass substrates. The power conversion efficiency (PCE) of the 0.1 wt% single-walled nanotubes (SWNTs)-TiO(X) nanocomposite device was almost doubled compared with the TiO(X) device, but with increasing concentration of the incorporated SWNTs in the TiO(X) film, the performance of the devices appeared to decrease rapidly. Devices with multi-walled NTs in the TiO(X) film have a similar trend. This phenomenon mainly depends on the inherent physical and chemical characteristics of CNTs such as their high surface area, their electron-accepting properties and their excellent carrier mobility. However, with increasing concentration of CNTs, CNTs-TiO(X) current leakage pathways emerged and also a recombination of charges at the interfaces. In addition, there was a significant discovery. The incorporated CNTs were highly conducive to enhancing the degree of crystallinity and the ordered arrangement of the P3HT in the active layers, due to the intermolecular π-π stacking interactions between CNTs and P3HT.

Substantial enhancement of energy storage capability in polymer nanocomposites by encapsulation of BaTiO3 NWs with variable shell thickness.

Science.gov (United States)

Wang, Guanyao; Huang, Yanhui; Wang, Yuxin; Jiang, Pingkai; Huang, Xingyi

2017-08-09

Dielectric polymer nanocomposites have received keen interest due to their potential application in energy storage. Nevertheless, the large contrast in dielectric constant between the polymer and nanofillers usually results in a significant decrease of breakdown strength of the nanocomposites, which is unfavorable for enhancing energy storage capability. Herein, BaTiO 3 nanowires (NWs) encapsulated by TiO 2 shells of variable thickness were utilized to fabricate dielectric polymer nanocomposites. Compared with nanocomposites with bare BaTiO 3 NWs, significantly enhanced energy storage capability was achieved for nanocomposites with TiO 2 encapsulated BaTiO 3 NWs. For instance, an ultrahigh energy density of 9.53 J cm -3 at 440 MV m -1 could be obtained for nanocomposites comprising core-shell structured nanowires, much higher than that of nanocomposites with 5 wt% raw ones (5.60 J cm -3 at 360 MV m -1 ). The discharged energy density of the proposed nanocomposites with 5 wt% mTiO 2 @BaTiO 3 -1 NWs at 440 MV m -1 seems to rival or exceed those of some previously reported nanocomposites (mostly comprising core-shell structured nanofillers). More notably, this study revealed that the energy storage capability of the nanocomposites can be tailored by the TiO 2 shell thickness. Finite element simulations were employed to analyze the electric field distribution in the nanocomposites. The enhanced energy storage capability should be mainly attributed to the smoother gradient of dielectric constant between the nanofillers and polymer matrix, which alleviated the electric field concentration and leakage current in the polymer matrix. The methods and results herein offer a feasible approach to construct high-energy-density polymer nanocomposites with core-shell structured nanowires.

Enhanced photocatalysis, colloidal stability and cytotoxicity of synchrotron X-ray synthesized Au/TiO{sub 2} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Liu, Chi-Jen; Yang, Tsung-Yeh; Wang, Chang-Hai [Institute of Physics, Academia Sinica, Nankang, Taipei 115, Taiwan (China); Chien, Chia-Chi [Institute of Physics, Academia Sinica, Nankang, Taipei 115, Taiwan (China); Department of Engineering Science and System, National Tsing Hua University, Hsinchu 300, Taiwan (China); Chen, Shin-Tai; Wang, Cheng-Liang; Leng, Wei-Hua [Institute of Physics, Academia Sinica, Nankang, Taipei 115, Taiwan (China); Hwu, Y., E-mail: phhwu@sinica.edu.tw [Institute of Physics, Academia Sinica, Nankang, Taipei 115, Taiwan (China); Department of Engineering Science and System, National Tsing Hua University, Hsinchu 300, Taiwan (China); Institute of Optoelectronic Sciences, National Taiwan Ocean University, Keelung 202, Taiwan (China); National Synchrotron Radiation Research Center, Hsinchu 300, Taiwan (China); Lin, Hong-Ming [Department of Materials Engineering, Tatung University, Taipei 10461, Taiwan (China); Lee, Yao-Chang [National Synchrotron Radiation Research Center, Hsinchu 300, Taiwan (China); Cheng, Chia-Liang [Department of Physics, National Dong Hwa University, Hualien 97401, Taiwan (China); Je, J.H. [X-ray Imaging Center, Pohang University of Science and Technology, Pohang (Korea, Republic of); Margaritondo, G. [Ecole Polytechnique Federale de Lausanne (EPFL), CH-1015 Lausanne (Switzerland)

2009-09-15

Au/TiO{sub 2} nanocomposite particles were synthesized by a method based on intense X-ray irradiation without adding any reducing agent or stabilizer. The nanocomposite exhibits promising photocatalytic and biological properties at physiologically relevant concentration ([Au] = 0.028 mM, [TiO{sub 2}] = 0.5 mM). The structure and photocatalysis were examined by X-ray diffraction, electron microscopy and ultraviolet-visible spectroscopy demonstrating that gold nanoparticles of 2-5 nm size were successfully deposited on TiO{sub 2} nanoparticle surfaces. The nanocomposite exhibited good colloidal stability within a typical cellular environment and was nontoxic to cancer cell according to evaluations under controlled conditions. The Au/TiO{sub 2} nanoparticles were also found to enhance the photocatalytic efficiency of UV radiation and even more that of X-ray radiation. In vitro studies indicated that the cell-killing effect under X-ray irradiation is more pronounced with the addition of Au/TiO{sub 2} nanoparticles than of bare TiO{sub 2} nanoparticles.

Photocatalytic activity enhancement by electron irradiation of fullerene derivative-TiO2 nanoparticles under visible light illumination

International Nuclear Information System (INIS)

Cho, Sung Oh; Yoo, Seung Hwa; Lee, Dong Hoon

2011-01-01

Photocatalytic decomposition of aqueous organic pollutant have attracted many interest due to its simple, low cost, and clean procedure. By only using the sun light and photocatalyst, especially TiO 2 nanoparticles based systems have been extensively studied and commercialized for real life application. However, TiO 2 has a critical disadvantage, which can only absorb the ultra-violet region of the solar spectrum, due to the large band-gap of 3.2 eV. Extensive studies have been preformed to expand the light absorption of TiO 2 to the visible light region of the solar spectrum, by doping metal or non-metal elements on TiO 2 or attaching small band-gap semiconductors on TiO 2 . In this study, a fullerene derivative 1-(3- carboxypropyl)-1-phenyl[6,6]C 61 (PCBA) was attached on the surface of TiO 2 nanoparticles, and its photocatalytic activity was evaluated by decomposition of methyl orange under visible light. Furthermore, enhancement in the photocatalytic activity of these nanoparticles by electron irradiation is discussed

Enhanced solar light photodegradation of brilliant black bis-azo dye in aqueous solution by F, Sm3+ codoped TiO2

Science.gov (United States)

Mukonza, Sabastian S.; Nxumalo, Edward N.; Mamba, Bhekie B.; Mishra, Ajay K.

2017-05-01

This research focuses on improving the photocatalytic efficiency of TiO2 during the photo-mineralisation of brilliant black (BN) bis-azo dye pollutant in aqueous solution. This was achieved by improving the visible light activity of TiO2 photocatalyst semiconductor through co-doping of fluorine (F) and trivalent samarium ions (Sm3+) into a TiO2 matrix using a modified sol-gel synthesis method. Structural, morphological, and textural properties were evaluated using ultra-violet /visible spectroscopy (UV-visible), Raman spectroscopy, scanning electron microscopy coupled to energy dispersive X-ray spectroscopy (SEM/EDX) and X-ray diffraction spectroscopy (XRD). Photocatalytic and degradation efficiencies were assessed by decolourisation of BN dye in aqueous solution. Complete degradation of BN was attained after an irradiation time of 3 h using F, Sm3+-TiO2 (0.6% Sm3+) compared to 73.4% achieved using pristine TiO2. Pseudo first order kinetics rate constants (Ka) were 2.73×10-2 and 6.6×10-3 min-1 for Sm3+-TiO2 (0.6%Sm3+) and pristine TiO2, respectively, which translates to a remarkably high enhancement factor of 4. The results obtained established that doping of TiO2 by F and Sm3+ enhances the photocatalytic performance of TiO2 during solar light radiation which enables the utilisation of freely available and clean solar energy.

Hierarchical Ag/AgCl-TiO{sub 2} hollow spheres with enhanced visible-light photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Wang, Xu Long; Yin, Hao Yong [College of Materials Environment Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Nie, Qiu Lin, E-mail: nieqiulin@hdu.edu.cn [College of Materials Environment Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Wu, Wei Wei [College of Materials Environment Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Zhang, Yang; LiYuan, Qiu [College of Science, Hangzhou Dianzi University, Hangzhou 310018 (China)

2017-01-01

The hierarchical Ag/AgCl-TiO{sub 2} hollow spheres were synthesized by depositing Ag/AgCl nanoparticles on TiO{sub 2} hollow spheres via a precipitation photoreduction method, and they were further characterized using TGA, SEM, TEM, XRD, XPS, UV–vis DRS and photoelectric chemical analysis. The analysis showed that the hierarchical Ag/AgCl-TiO{sub 2} hollow spheres exhibited the highest photocatalytic activity, which was approximately 13 times higher than that of TiO{sub 2} hollow spheres. The high photocatalytic activity of the composites is due to efficient electron-hole pairs separation at the photocatalyst interfaces, and localized surface plasmon resonance of Ag nanoparticles formed on AgCl particles in the degradation reaction. - Highlights: • TiO{sub 2} hollow spheres were prepared by a sacrificial template method. • The hollow spheres were modified with Ag/AgCl to form the heterojunctions. • The modification may produce synergistic effect of LSPR and hollow structure. • Visible light photocatalytic activity was enhanced on this hollow catalyst. • The mechanism of the improved photocatalytic performance was discussed.

Significant enhancement in volumetric and gravimetric capacitance of Cu-TiO2/PPY composite for supercapacitor application

Science.gov (United States)

Purty, B.; Choudhary, R. B.

2018-04-01

Copper doped titanium dioxide-polypyrrole (Cu-TiO2/PPY) composite was successfully synthesized via chemical oxidative in-situ polymerization process. The structural and morphological properties of Cu-TiO2/PPY composite were investigated using X-ray diffractometer (XRD), field emission electron microscopy (FESEM) and transmission electron microscopy(TEM) techniques. The electrochemical properties of as-synthesized composite were studied using cyclic voltammetry (CV), galvanostatic charge discharge (GCD) and electrochemical impedance spectroscopic (EIS) techniques. The novel Cu-TiO2/PPY composite showed enhanced volumetric capacitance ˜714 F cm-1 and gravimetric capacitance ˜674 F g-1 at 1 A g-1. In addition an excellent coulombic efficiency and comparabley low charge transfer resistance than pure PPY suggests improved supercapacitive performance of Cu-TiO2/PPY composite as an electrode material.

Efficient dye-sensitized solar cells from curved silicate microsheet caged TiO2 photoanodes. An avenue of enhancing light harvesting

International Nuclear Information System (INIS)

Wang, Zubin; Tang, Qunwei; He, Benlin; Chen, Haiyan; Yu, Liangmin

2015-01-01

Graphical abstract: - Highlights: • Curved silicate microsheets are incorporated with TiO 2 for light harvesting in DSSC • The optical matching between silicate and TiO 2 is superior to light reflection. • The curved silicate can hinder the recombination reaction of electrons with I 3 − . • The DSSC with TiO 2 /curved silicate photoanode shows an efficiency of 9.22% - Abstract: Enhancement of light harvesting has been a persistent objective for elevating dye excitation and therefore power conversion efficiency of dye-sensitized solar cells (DSSCs). Here we launch a strategy of markedly enhancing light harvesting by caging TiO 2 nanoparticles with curved silica microsheets. The results show that the strategy is versatile in suppressing the recombination reaction of electrons with I 3 − species in liquid electrolyte. Due to the superior reflective behaviors of curved silica microsheets, an optimal efficiency of 9.22% is recorded under simulated air mass 1.5 global sunlight on the DSSC in comparison with 6.51% and 7.51% from pristine TiO 2 and planar silicate microsheet incorporated TiO 2 photoanode based solar cells, respectively. This strategy is also believed to be applicable to other solar cells such as perovskite solar cells and quantum dot-sensitized solar cells.

Synthesis of Br-doped TiO{sub 2} hollow spheres with enhanced photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Wang, Qianqian; Zhu, Shengli, E-mail: slzhu@tju.edu.cn; Liang, Yanqin; Cui, Zhenduo; Yang, Xianjin [Tianjin University, School of Materials Science and Engineering (China); Liang, Chunyong [Hebei University of Technology, Research Institute for Energy Equipment Materials (China); Inoue, Akihisa [Tianjin University, School of Materials Science and Engineering (China)

2017-02-15

The Br-doped hollow TiO{sub 2} photocatalysts were prepared by a simple hydrothermal process on the carbon sphere template following with calcination at 400 °C. The structure and properties of photocatalysts were characterized by X-ray diffraction, Raman spectrum, scanning electron microscope, transmission electron microscopy, N{sub 2} desorption–adsorption, UV–Vis spectroscopy, and X-ray photoelectron spectroscopy. The TiO{sub 2} hollow spheres are in diameter of 500 nm with shell thickness of 50 nm. The shell is composed of small anatase nanoparticles with size of about 10 nm. The TiO{sub 2} hollow spheres exhibit high crystalline and high surface area of 89.208 m{sup 2}/g. With increasing content of Br doping, the band gap of TiO{sub 2} hollow spheres decreased from 2.85 to 1.75 eV. The formation of impurity band in the band gap would narrow the band gap and result in the red shift of absorption edge from 395 to 517 nm, which further enhances the photocatalytic activity. The appropriate Br doping improves the photocatlytic activity significantly. The TiO{sub 2} hollow spheres with 1.55% Br doping (0.5Br-TiO{sub 2}) exhibit the highest photocatalytic activity under full light. More than 98% of RhB, MO, and MB can be photodegraded using 0.5Br-TiO{sub 2} with concentration of 10 mg/L in 40, 30, and 30 min, respectively. The degradation rate of Br-doped photocatalysts was 40% faster than undoped ones.

Heterojunctions of p-BiOI Nanosheets/n-TiO2 Nanofibers: Preparation and Enhanced Visible-Light Photocatalytic Activity

Directory of Open Access Journals (Sweden)

Kexin Wang

2016-01-01

Full Text Available p-BiOI nanosheets/n-TiO2 nanofibers (p-BiOI/n-TiO2 NFs have been facilely prepared via the electrospinning technique combining successive ionic layer adsorption and reaction (SILAR. Dense BiOI nanosheets with good crystalline and width about 500 nm were uniformly assembled on TiO2 nanofibers at room temperature. The amount of the heterojunctions and the specific surface area were well controlled by adjusting the SILAR cycles. Due to the synergistic effect of p-n heterojunctions and high specific surface area, the obtained p-BiOI/n-TiO2 NFs exhibited enhanced visible-light photocatalytic activity. Moreover, the p-BiOI/n-TiO2 NFs heterojunctions could be easily recycled without decreasing the photocatalytic activity owing to their one-dimensional nanofibrous structure. Based on the above, the heterojunctions of p-BiOI/n-TiO2 NFs may be promising visible-light-driven photocatalysts for converting solar energy to chemical energy in environment remediation.

Characterizations of MoTiO5 flash memory devices with post-annealing

International Nuclear Information System (INIS)

Kao, Chyuan Haur; Chen, Hsiang; Chen, Su Zhien; Chen, Yu Jie; Chu, Yu Cheng

2014-01-01

In this study, high-K MoTiO 5 dielectrics were applied as charge trapping layers in fabricated metal-oxide-high-K MoTiO 5 -oxide-Si-type memory devices. Among the applied MoTiO 5 trapping layer treatment conditions, annealing at 900 °C yielded devices that exhibited superior memory performance, such as a larger memory window and faster programming/erasing speed. Multiple material analyses, namely X-ray diffraction, X-ray photoelectron spectroscopy, and atomic force microscopy, confirmed that annealing at 900 °C can improve the material quality as a result of crystallization. The fabricated MoTiO 5 -based memory devices show potential for future commercial memory device applications. - Highlights: • MoTiO5-based flash memories have been fabricated. • MoTiO5 trapping layers could be formed by co-sputtering. • MoTiO5 layers with annealing exhibited a good memory performance. • Multiple material analyses confirm that annealing enhanced crystallization

Hydrothermal synthesis of core–shell TiO_2 to enhance the photocatalytic hydrogen evolution

International Nuclear Information System (INIS)

Jiang, Jinghui; Zhou, Han; Zhang, Fan; Fan, Tongxiang; Zhang, Di

2016-01-01

Graphical abstract: Core–shell TiO_2 with interior cavity was synthesized by a hydrothermal approach to enhance the photocatalytic performance. - Highlights: • Core–shell TiO_2 with interior cavity can be synthesized by hydrothermal approach. • Multiple reflection of incident light in cavity can increase the absorption. • Rutile can optimize the bandgap and delay the charge recombination. - Abstract: A hydrothermal approach was designed to synthesize core–shell TiO_2 with interior cavity by making sodium dodecyl sulfonate (SDS) as the surfactant and the mixture of water and ethanol as the solvent. The control experiment of solvent reveals ethanol and water are responsible for the formation of sphere and interior cavity, respectively. Besides, SDS can assist the growth of core–shell structure, and the sizes of sphere and interior cavity can be tuned by regulating the reaction time or temperature. UV–vis absorption proves core–shell structure with interior cavity can increase the absorption of incident light to enhance the optical activity of final product. The calculated bandgap and photoluminescence (PL) analyses reveal the coexistence of rutile in final product can optimize the bandgap to 3.03 eV and delay the charge recombination. As a result, an effective photocatalytic hydrogen evolution under full spectrum irradiation can be harvested by the as-synthesized core–shell spheres to reach a quantum yield, approximately 9.57% at 340 nm wavelength.

Nanometer-thin TiO2 enhances skeletal muscle cell phenotype and behavior

Directory of Open Access Journals (Sweden)

Ishizaki K

2011-10-01

enhance their biological properties without altering the existing microscale morphology. The controllable and exclusive chemical modification technique presented in this study may open a new avenue for surface modifications of titanium-based biomaterials for better cell and tissue affinity and reaction.Keywords: nanotechnology, orthopedic implants, molten TiO2 nanoparticles, surface chemistry

Development of TiO2 containing hardmasks through plasma-enhanced atomic layer deposition

Science.gov (United States)

De Silva, Anuja; Seshadri, Indira; Chung, Kisup; Arceo, Abraham; Meli, Luciana; Mendoza, Brock; Sulehria, Yasir; Yao, Yiping; Sunder, Madhana; Truong, Hoa; Matham, Shravan; Bao, Ruqiang; Wu, Heng; Felix, Nelson M.; Kanakasabapathy, Sivananda

2017-04-01

With the increasing prevalence of complex device integration schemes, trilayer patterning with a solvent strippable hardmask can have a variety of applications. Spin-on metal hardmasks have been the key enabler for selective removal through wet strip when active areas need to be protected from dry etch damage. As spin-on metal hardmasks require a dedicated track to prevent metal contamination and are limited in their ability to scale down thickness without compromising on defectivity, there has been a need for a deposited hardmask solution. Modulation of film composition through deposition conditions enables a method to create TiO2 films with wet etch tunability. This paper presents a systematic study on development and characterization of plasma-enhanced atomic layer deposited (PEALD) TiO2-based hardmasks for patterning applications. We demonstrate lithographic process window, pattern profile, and defectivity evaluation for a trilayer scheme patterned with PEALD-based TiO2 hardmask and its performance under dry and wet strip conditions. Comparable structural and electrical performance is shown for a deposited versus a spin-on metal hardmask.

Enhanced conversion efficiency of dye-sensitized solar cells using a CNT-incorporated TiO2 slurry-based photoanode

Directory of Open Access Journals (Sweden)

Jiaoping Cai

2015-02-01

Full Text Available A new titanium dioxide (TiO2 slurry formulation is herein reported for the fabrication of TiO2 photoanode for use in dye-sensitized solar cells (DSSCs. The prepared TiO2 photoanode featured a highly uniform mesoporous structure with well-dispersed TiO2 nanoparticles. The energy conversion efficiency of the resulting TiO2 slurry-based DSSC was ∼63% higher than that achieved by a DSSC prepared using a commercial TiO2 slurry. Subsequently, the incorporation of acid-treated multi-walled carbon nanotubes (CNTs into the TiO2 slurry was examined. More specifically, the effect of varying the concentration of the CNTs in this slurry on the performance of the resulting DSSCs was studied. The chemical state of the CNTs-incorporated TiO2 photoanode was investigated by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. A high energy conversion efficiency of 6.23% was obtained at an optimum CNT concentration of ∼0.06 wt.%. The obtained efficiency corresponds to a 63% enhancement when compared with that obtained from a DSSC based on a commercial TiO2 slurry. The higher efficiency was attributed to the improvement in the collection and transport of excited electrons in the presence of the CNTs.

Enhanced conversion efficiency of dye-sensitized solar cells using a CNT-incorporated TiO2 slurry-based photoanode

Science.gov (United States)

Cai, Jiaoping; Chen, Zexiang; Li, Jun; Wang, Yan; Xiang, Dong; Zhang, Jijun; Li, Hai

2015-02-01

A new titanium dioxide (TiO2) slurry formulation is herein reported for the fabrication of TiO2 photoanode for use in dye-sensitized solar cells (DSSCs). The prepared TiO2 photoanode featured a highly uniform mesoporous structure with well-dispersed TiO2 nanoparticles. The energy conversion efficiency of the resulting TiO2 slurry-based DSSC was ˜63% higher than that achieved by a DSSC prepared using a commercial TiO2 slurry. Subsequently, the incorporation of acid-treated multi-walled carbon nanotubes (CNTs) into the TiO2 slurry was examined. More specifically, the effect of varying the concentration of the CNTs in this slurry on the performance of the resulting DSSCs was studied. The chemical state of the CNTs-incorporated TiO2 photoanode was investigated by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. A high energy conversion efficiency of 6.23% was obtained at an optimum CNT concentration of ˜0.06 wt.%. The obtained efficiency corresponds to a 63% enhancement when compared with that obtained from a DSSC based on a commercial TiO2 slurry. The higher efficiency was attributed to the improvement in the collection and transport of excited electrons in the presence of the CNTs.

Enhancement of photocatalytic degradation of polyethylene plastic with CuPc modified TiO2 photocatalyst under solar light irradiation

International Nuclear Information System (INIS)

Zhao Xu; Li Zongwei; Chen Yi; Shi Liyi; Zhu Yongfa

2008-01-01

Solid-phase photocatalytic degradation of polyethylene (PE) plastic, one of the most common commercial plastic, over copper phthalocyanine (CuPc) modified TiO 2 (TiO 2 /CuPc) photocatalyst was investigated in the ambient air under solar light irradiation. Higher PE weight loss rate, greater texture change; more amount of generated CO 2 , which is the main product of the photocatalytic degradation of the composite PEC plastic can be achieved in the system of PE-(TiO 2 /CuPc) in comparison with PE-TiO 2 system. The CuPc promoted charge separation of TiO 2 and enhanced the photocatalytic degradation of PE based on the analysis of surface photovoltage spectroscopy (SPS). During the photodegradation of PE plastic, the reactive oxygen species generated on TiO 2 or TiO 2 /CuPc particle surfaces play important roles. The present study demonstrates that the combination of polymer plastic with TiO 2 /CuPc composite photocatalyst in the form of thin film is a practical and useful way to photodegrade plastic contaminants under solar light irradiation

Enhancement of TiO2 NPs Activity by Fe3O4 Nano-Seeds for Removal of Organic Pollutants in Water

Directory of Open Access Journals (Sweden)

Silvia Villa

2016-09-01

Full Text Available The enhancement of the photocatalytic activity of TiO2 nanoparticles (NPs, synthesized in the presence of a very small amount of magnetite (Fe3O4 nanoparticles, is here presented and discussed. From X-ray diffraction (XRD and differential scanning calorimetry (DSC analyses, the crystallinity of TiO2 nanoparticles (NPs seems to be affected by Fe3O4, acting as nano-seeds to improve the tetragonal TiO2 anatase structure with respect to the amorphous one. Photocatalytic activity data, i.e., the degradation of methylene blue and the Ofloxacin fluoroquinolone emerging pollutant, give evidence that the increased crystalline structure of the NPs, even if correlated to a reduced surface to mass ratio (with respect to commercial TiO2 NPs, enhances the performance of this type of catalyst. The achievement of a relatively well-defined crystal structure at low temperatures (Tmax = 150 °C, preventing the sintering of the TiO2 NPs and, thus, preserving the high density of active sites, seems to be the keystone to understand the obtained results.

Three-dimensional ruthenium-doped TiO ₂ sea urchins for enhanced visible-light-responsive H ₂ production

Energy Technology Data Exchange (ETDEWEB)

Nguyen-Phan, Thuy-Duong; Luo, Si; Vovchok, Dimitriy; Llorca, Jordi; Sallis, Shawn; Kattel, Shyam; Xu, Wenqian; Piper, Louis F. J.; Polyansky, Dmitry E.; Senanayake, Sanjaya D.; Stacchiola, Dario J.; Rodriguez, José A.

2016-01-01

Three-dimensional (3D) monodispersed sea urchin-like Ru-doped rutile TiO2 hierarchical architectures composed of radially aligned, densely-packed TiO2 nanorods have been successfully synthesized via an acid-hydrothermal method at low temperature without the assistance of any structure-directing agent and post annealing treatment. The addition of a minuscule concentration of ruthenium dopants remarkably catalyze the formation of the 3D urchin structure and drive the enhanced photocatalytic H2 production under visible light irradiation, not possible on undoped and bulk rutile TiO2. Increasing ruthenium doping dosage not only increases the surface area up to 166 m2 g-1 but also induces enhanced photo response in the regime of visible and near infrared light. The doping introduces defect impurity levels, i.e. oxygen vacancy and under-coordinated Ti3+, significantly below the conduction band of TiO2, and ruthenium species act as electron donors/acceptors that accelerate the photogenetated hole and electron transfer and efficiently suppress the rapid charge recombination, therefore improving the visible-light-driven activity.

Experimental Study on Impact-Induced Reaction Characteristics of PTFE/Ti Composites Enhanced by W Particles

Directory of Open Access Journals (Sweden)

Yan Li

2017-02-01

Full Text Available Metal/fluoropolymer composites are a category of energetic structural materials that release energy through exothermic chemical reactions initiated under highly dynamic loadings. In this paper, the chemical reaction mechanism of PTFE (polytetrafluoroethylene/Ti/W composites is investigated through thermal analysis and composition analysis. These composites undergo exothermic reactions at 510 °C to 600 °C, mainly producing TiFx. The tungsten significantly reduces the reaction heat due to its inertness. In addition, the dynamic compression properties and impact-induced reaction behaviors of PTFE/Ti/W composites with different W content prepared by pressing and sintering are studied using Split Hopkinson Pressure Bar and high speed photography. The results show that both the mechanical strength and the reaction degree are significantly improved with the increasing strain rate. Moreover, as W content increases, the mechanical strength is enhanced, but the elasticity/plasticity is decreased. The PTFE/Ti/W composites tend to become more inert with the increasing W content, which is reflected by the reduced reaction degree and the increased reaction threshold for the impact ignition.

Band-offsets at BaTiO3/Cu2O heterojunction and enhanced photoelectrochemical response: theory and experiment(Conference Presentation)

Science.gov (United States)

Sharma, Dipika; Satsangi, Vibha R.; Dass Kaura, Sahab; Shrivastav, Rohit; Waghmare, Umesh V.

2016-10-01

Band-offsets at BaTiO3/Cu2O heterojunction and enhanced photoelectrochemical response: theory and experiment Dipika Sharmaa, Vibha R. Satsangib, Rohit Shrivastava, Umesh V. Waghmarec, Sahab Dassa aDepartment of Chemistry, Dayalbagh Educational Institute, Agra-282 110 (India) bDepartment of Physics and Computer Sciences, Dayalbagh Educational Institute, Agra-282 110 (India) cTheoretical Sciences Unit, Jawaharlal Nehru Centre for Advanced Scientific Research, Jakkur, Bangalore-560 064 (India) * Phone: +91-9219695960. Fax: +91-562-2801226. E-mail: drsahabdas@gmail.com. Study on photoelectrochemical activity of pristine BaTiO3, Cu2O and BaTiO3/Cu2O heterojunction has been carried out using DFT based band offsets and charge carriers effective mass calculations and their experimental verification. The results of DFT calculations show that BaTiO3 and Cu2O have staggered type band alignment after the heterojunction formation and high mobility of electrons in Cu2O as compared to the electrons in BaTiO3. Staggered type band edges alignment and high mobility of electrons and holes improved the separation of photo-generated charge carriers in BaTiO3/Cu2O heterojunction. To validate the theoretical results experiments were carried out on pristine BaTiO3, Cu2O and BaTiO3/Cu2O heterojunction with varying thickness of Cu2O. All samples were characterized by X- Ray Diffractometer, SEM and UV-Vis spectrometry. Nanostructured thin films of pristine BaTiO3, Cu2O and BaTiO3/Cu2O heterojunction were used as photoelectrode in the photoelectrochemical cell for water splitting reaction. Maximum photocurrent density of 1.44 mA/cm2 at 0.90 V/SCE was exhibited by 442 nm thick BaTiO3/Cu2O heterojunction photoelectrode Increased photocurrent density and enhanced photoconversion efficiency, exhibited by the heterojunction may be attributed to improved conductivity and enhanced separation of the photogenerated carriers at the BaTiO3/Cu2O interface. The experimental results and first

Synthesis of Cu{sub 2}O/graphene/rutile TiO{sub 2} nanorod ternary composites with enhanced photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Sun, Mingxuan, E-mail: mingxuansun@sues.edu.cn; Fang, Yalin; Wang, Ying; Sun, Shanfu; He, Jia; Yan, Zhi

2015-11-25

A ternary composite of Cu{sub 2}O, graphene and rutile TiO{sub 2} nanorods was prepared using Cu(CH{sub 3}COO){sub 2}·H{sub 2}O, graphene oxide and TiCl{sub 4} as the starting materials and its enhanced photocatalytic performance was demonstrated. Graphene/TiO{sub 2} nanorod composites (GT) were obtained by a simple hydrothermal method and then, Cu{sub 2}O was coupled onto the surface of graphene/rutile TiO{sub 2} to form Cu{sub 2}O/graphene/rutile TiO{sub 2} nanorod (CGT) composites via a chemical bath deposition process. The as-prepared sample was characterized by X-ray diffraction (XRD), emission field scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), specific surface area analyzer (BET), Raman spectroscopy and ultraviolet–visible diffuse reflectance spectroscopy (UV–vis DRS). It is found that the introduction of graphene and Cu{sub 2}O has little effect on the morphology of TiO{sub 2} nanorods with average dimensions of 140 nm (length) × 30 nm (diameter) (L/D ratio ≈5). A red shift of light absorption edge and more absorption in the visible light region were observed for the resulted ternary samples compared with TiO{sub 2} and graphene/TiO{sub 2} composites. The photocatalytic activity was evaluated by the photodegradation of methylene blue under visible light irradiation, which showed 2.8 times corresponding enhancement of the degradation efficiency for the ternary composites compared with TiO{sub 2}. This work provides a new strategy to improve the visible light response of TiO{sub 2} and facilitate its application in environmental remediation. - Highlights: • A ternary composite of Cu{sub 2}O/graphene/rutile TiO{sub 2} nanorods were successfully fabricated. • Red shift and more absorption in the visible light region were observed for the ternary composites. • Improved photocatalytic degradation was detected with the introduction of Cu{sub 2}O and graphene. • Both Cu{sub 2}O and graphene played an important role

Enhanced photocatalytic CO₂-reduction activity of electrospun mesoporous TiO₂ nanofibers by solvothermal treatment.

Science.gov (United States)

Fu, Junwei; Cao, Shaowen; Yu, Jiaguo; Low, Jingxiang; Lei, Yongpeng

2014-06-28

Photocatalytic reduction of CO2 into renewable hydrocarbon fuels using semiconductor photocatalysts is considered as a potential solution to the energy deficiency and greenhouse effect. In this work, mesoporous TiO2 nanofibers with high specific surface areas and abundant surface hydroxyl groups are prepared using an electrospinning strategy combined with a subsequent calcination process, followed by a solvothermal treatment. The solvothermally treated mesoporous TiO2 nanofibers exhibit excellent photocatalytic performance on CO2 reduction into hydrocarbon fuels. The significantly improved photocatalytic activity can be attributed to the enhanced CO2 adsorption capacity and the improved charge separation after solvothermal treatment. The highest activity is achieved for the sample with a 2-h solvothermal treatment, showing 6- and 25-fold higher CH4 production rate than those of TiO2 nanofibers without solvothermal treatment and P25, respectively. This work may also provide a prototype for studying the effect of solvothermal treatment on the structure and photocatalytic activity of semiconductor photocatalysts.

Synthesis and characterization of anionic/nonionic surfactant-interceded iron-doped TiO{sub 2} to enhance sorbent/photo-catalytic properties

Energy Technology Data Exchange (ETDEWEB)

Sharma, Ajit; Lee, Byeong-Kyu, E-mail: bklee@ulsan.ac.kr

2015-09-15

We investigated the synthesis, characterization, and application of surfactant-interceded Fe nanoparticle-doped TiO{sub 2} (TiO{sub 2}/Fe-S1 and TiO{sub 2}/Fe-S2) that were used as adsorbents and photo-catalysts for the removal of As(V) ions from aqueous media. Two types of surfactant (anionic (sodium dodecyl sulfate), S1 and non-ionic (Triton X-100), S2) were used to obtain the separation and mono-dispersion of Fe(III) ions in the reaction solution. The nanocomposites were characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), UV–vis, scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX) and elemental mapping analysis before and after As(V) removal. The Langmuir capacities (q{sub e}, mg/g) of the sodium dodecyl sulfate (SDS) and Triton X-100 interceded nanocomposites (TiO{sub 2}/Fe-S1 and TiO{sub 2}/Fe-S2, respectively) for arsenic removal were determined to be 65.79 and 50.76 mg/g, respectively, in aqueous media with As(V) concentration ranges of 0–10 mg/L at pH 6.5. - Highlights: • Fe(III) doped TiO{sub 2} nanocomposite was prepared with surfactant. • Anionic surfactant SDS enhanced the transfer of Fe(III) ions to TiO{sub 2}. • Surfactant-interceded nanocomposite enhanced As(V) removal. • Arsenic removal efficiency was as follows: dark phase>visible phase>UV region.

Porous TiO_2 nanofibers decorated CdS nanoparticles by SILAR method for enhanced visible-light-driven photocatalytic activity

International Nuclear Information System (INIS)

Tian, Fengyu; Hou, Dongfang; Hu, Fuchao; Xie, Kui; Qiao, Xiuqing; Li, Dongsheng

2017-01-01

Graphical abstract: A heterojunction photocatalyst with CdS Nanoparticles self-assembled via SILAR Method at surfaces of electrospun TiO2 nanofibers shows enhanced visible-light photocatalytic activities. - Highlights: • Combined electrospinning and successive ionic layer adsorption and reaction process. • Pouous TiO_2 nanofibers decorated CdS nanoparticles. • Synergetic effect of photosensitization and heterojunction. - Abstract: 1D porous CdS nanoparticles/TiO_2 nanofibers heterostructure has been fabricated via simple electrospinning and a successive ionic layer adsorption and reaction (SILAR) process. The morphology, composition, and optical properties of the resulting CdS/TiO_2 heterostructures can be rationally tailored through changing the SILAR cycles. The photocatalytic hydrogen evolution and decomposition of rhodamine B (RhB) of the as-synthesized heterostructured photocatalysts were investigated under visible light irradiation. Compared to TiO_2 nanofibers，the as-obtained CdS/TiO_2 heterostructures exhibit enhanced photocatalytic activity for hydrogen production and decomposition of RhB under visible-light irradiation. The heterojunction system performs best with H_2 generation rates of 678.61 μmol h"−"1 g"−"1 under visible light irradiation which benefits from the two effects: (a) the 1D porous nanofibrous morphology contributes to not only more active sites but also more efficient transfer of the photogenerated charges (b) the synergetic effect of heterojunction and photosensitization reducing the recombination of photogenerated electrons and holes.

Investigation of radiation-enhanced oxygen diffusion in Li-Ti ferrites

International Nuclear Information System (INIS)

Surzhikov, A.P.; Pritulov, A.M.; Gyngazov, S.A.; Lysenko, E.N.

1999-01-01

The radiation-enhanced oxygen diffusion in polycrystalline Li-Ti ferrites was investigated. The electron accelerator ELV-6 (Institute of Nuclear Physics, Russian Academy of Sciences) was used to generate the radiothermal annealing. The radiation effects were established by comparison of diffusion profiles of the samples, which were radiothermally treated, and data obtained during the thermal annealing in the resistance furnace. It was discovered that there was an increase of numerical values of Ed (activation diffusion energy) and Do (preexponential factor) during the radiothermal annealing, if compared with the thermal one. The investigations were financed by the Russian Fundamental Research Fund

ITO-TiN-ITO Sandwiches for Near-Infrared Plasmonic Materials.

Science.gov (United States)

Chen, Chaonan; Wang, Zhewei; Wu, Ke; Chong, Haining; Xu, Zemin; Ye, Hui

2018-05-02

Indium tin oxide (ITO)-based sandwich structures with the insertion of ultrathin (ITO layers show TiN-thickness-dependent properties, which lead to moderate and tunable effective permittivities for the sandwiches. The surface plasmon polaritons (SPP) of the ITO-TiN-ITO sandwich at the telecommunication window (1480-1570 nm) are activated by prism coupling using Kretschmann configuration. Compared with pure ITO films or sandwiches with metal insertion, the reflectivity dip for sandwiches with TiN is relatively deeper and wider, indicating the enhanced coupling ability in plasmonic materials for telecommunications. The SPP spatial profile, penetration depth, and degree of confinement, as well as the quality factors, demonstrate the applicability of such sandwiches for NIR plasmonic materials in various devices.

Enhancement of Ti-containing hydrogenated carbon (Ti-C:H) films by high-power plasma-sputtering

International Nuclear Information System (INIS)

Gwo, Jyh; Chu, Chun-Lin; Tsai, Ming-Jui; Lee, Shyong

2012-01-01

Ti-containing amorphous hydrogenated carbon (Ti-C:H) thin films were deposited on stainless steel SS304 substrates by high-power pulsed magnetron sputtering (HPPMS) in an atmosphere of mixed Ar and C 2 H 2 gases using titanium metal as the cathodic material. The multilayer structure of the deposited film had a Ti-TiC-DLC gradient to improve adhesion and reduce residual stress. This study investigates the effects of substrate bias and target-to-substrate distance on the mechanical properties of Ti-C:H films. Film properties, including composition, morphology, microstructure, mechanical, and tribology, were examined by glow discharge spectroscopy (GDS), scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, and a nanoindenter and a pin-on-disk tribometer. Experiments revealed impressive results.

Double-layer composite film based on sponge-like TiO{sub 2} and P25 as photoelectrode for enhanced efficiency in dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Dai Guotian [Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, Faculty of Materials Science and Engineering, Hubei University, Wuhan 430062 (China); Zhao Li, E-mail: zhaoli7376@163.com [Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, Faculty of Materials Science and Engineering, Hubei University, Wuhan 430062 (China); Wang Shimin; Hu Jinhua; Dong Binghai; Lu Hongbing; Li Jing [Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, Faculty of Materials Science and Engineering, Hubei University, Wuhan 430062 (China)

2012-10-25

Highlights: Black-Right-Pointing-Pointer A novel TiO{sub 2} double-layer composite film is successfully fabricated. Black-Right-Pointing-Pointer The overlayer enhances light-harvesting efficiency and electron transport. Black-Right-Pointing-Pointer The underlayer ensures good electronic contact between TiO{sub 2} film and FTO. Black-Right-Pointing-Pointer TiO{sub 2} double-layer composite film cells have the maximum conversion efficiency. - Abstract: A TiO{sub 2} double-layer composite film consisting of hierarchically sponge-like macro-/mesoporous TiO{sub 2} (HSMM-TiO{sub 2}) as overlayer and commercial-grade TiO{sub 2} nanoparticles (P25) as underlayer is designed as the photoelectrode of dye-sensitized solar cells (DSSCs). The photoelectric conversion performances of DSSCs based on P25 nanoparticle film, HSMM-TiO{sub 2} film, and P25/HSMM-TiO{sub 2} double-layer composite film are investigated and compared. It is found that the overall energy-conversion efficiency of 5.48% is achieved by the formation of P25/HSMM-TiO{sub 2} double-layer composite film, which is 51.4% higher than that formed by P25 nanoparticle film ({eta} = 3.62%) and 27.1% higher than that formed by HSMM-TiO{sub 2} film ({eta} = 4.31%) under identical film thickness (ca. 20 {mu}m) at a constant irradiation of 100 mWcm{sup -2}. The enhanced conversion efficiency of TiO{sub 2} double-layer composite film can be attributed to the combined effect of the following factors. The HSMM-TiO{sub 2} overlayer enhances light-harvesting efficiency due to its intense light scattering and the P25 nanoparticle underlayer ensures good electronic contact between TiO{sub 2} film and the F-doped tin oxide (FTO) glass. Furthermore, the high specific surface area and special pore-wall structure of HSMM-TiO{sub 2} are respectively beneficial to adsorption of dye molecules and transport of both electrons and electrolytes.

Enhancement of photocatalytic properties of TiO2 nanoparticles doped with CeO2 and supported on SiO2 for phenol degradation

International Nuclear Information System (INIS)

Hao, Chunjing; Li, Jing; Zhang, Zailei; Ji, Yongjun; Zhan, Hanhui; Xiao, Fangxing; Wang, Dan; Liu, Bin; Su, Fabing

2015-01-01

Highlights: • CeO 2 -TiO 2 /SiO 2 composites were prepared via a facile co-precipitation method. • Introduction of SiO 2 support increases the dispersion of CeO 2 -TiO 2 . • CeO 2 -TiO 2 /SiO 2 exhibits an enhanced photocatalytic efficiency for phenol degradation. • Ce 3+ /Ce 4+ pair coexisting in CeO 2 improves electron–hole pairs separation efficiency. - Abstract: A series of CeO 2 -TiO 2 and CeO 2 -TiO 2 /SiO 2 composites were prepared with TiCl 4 and Ce (NO 3 ) 3 ·6H 2 O as precursors via a facile co-precipitation method. The obtained samples were characterized by various techniques such as X-ray diffraction (XRD), nitrogen adsorption (N 2 -BET), Fourier transformation infrared spectrum (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and UV–Vis spectroscopy measurements. The results indicated that TiO 2 doped with CeO 2 and supported on SiO 2 could reduce the crystallite size, inhibit the phase transformation, enhance the thermal stability, and effectively extend the spectral response from UV to visible range. When applied to the phenol photodegradation on a homemade batch reactor with an external cooling jacket, the CeO 2 -TiO 2 /SiO 2 catalysts exhibited significantly enhanced photodegradation efficiency in comparison with commercial Degussa P25 and CeO 2 -TiO 2 . The unique catalytic properties of CeO 2 -TiO 2 /SiO 2 were ascribed to improved electron–hole pairs separation efficiency and formation of more reactive oxygen species owing to the presence of Ce 3+ /Ce 4+ , as well as high dispersion of active component of CeO 2 -TiO 2 as a result of the introduction of SiO 2 support. Furthermore, the catalysts can be easily recovered from the reaction solution by centrifugation and reused for four cycles without significant loss of activity

Enhanced photoelectrochemical and photocatalytic behaviors of MFe2O4 (M = Ni, Co, Zn and Sr) modified TiO2 nanorod arrays

Science.gov (United States)

Gao, Xin; Liu, Xiangxuan; Zhu, Zuoming; Wang, Xuanjun; Xie, Zheng

2016-07-01

Modified TiO2 nanomaterials are considered to be promising in energy conversion and ferrites modification may be one of the most efficient modifications. In this research, various ferrites, incorporated with various cations (MFe2O4, M = Ni, Co, Zn, and Sr), are utilized to modify the well aligned TiO2 nanorod arrays (NRAs), which is synthesized by hydrothermal method. It is found that all MFe2O4/TiO2 NRAs show obvious red shift into the visible light region compared with the TiO2 NRAs. In particular, NiFe2O4 modification is demonstrated to be the best way to enhance the photoelectrochemical and photocatalytic activity of TiO2 NRAs. Furthermore, the separation and transfer of charge carriers after MFe2O4 modification are clarified by electrochemical impedance spectroscopy measurements. Finally, the underlying mechanism accounting for the enhanced photocatalytic activity of MFe2O4/TiO2 NRAs is proposed. Through comparison among different transition metals modified TiO2 with the same synthesis process and under the same evaluating condition, this work may provide new insight in designing modified TiO2 nanomaterials as visible light active photocatalysts.

Enhanced photocatalytic properties of hierarchical three-dimensional TiO{sub 2} grown on femtosecond laser structured titanium substrate

Energy Technology Data Exchange (ETDEWEB)

Huang, Ting, E-mail: huangting@bjut.edu.cn; Lu, Jinlong; Xiao, Rongshi; Wu, Qiang; Yang, Wuxiong

2017-05-01

Highlights: • The hierarchical 3D-TiO{sub 2} is fabricated on femtosecond laser structured Ti substrate. • The formation mechanism of hierarchical 3D-TiO{sub 2} is proposed. • The structure-induced improvement of photocatalytic activity is reported. - Abstract: Three-dimensional micro-/nanostructured TiO{sub 2} (3D-TiO{sub 2}) fabricated on titanium substrate effectively improves its performance in photocatalysis, dye-sensitized solar cell and lithium-ion battery applications. In this study, the hierarchical 3D-TiO{sub 2} with anatase phase directly grown on femtosecond laser structured titanium substrate is reported. First, the primary columnar arrays were fabricated on the surface of titanium substrate by femtosecond laser structuring. Next, the secondary nano-sheet substructures were grown on the primary columnar arrays by NaOH hydrothermal treatment. Followed by ion-exchange process in HCl and annealing in the air, the hierarchical anatase 3D-TiO{sub 2} was achieved. The hierarchical anatase 3D-TiO{sub 2} exhibited enhanced performances in light harvesting and absorption ability compared to that of nano-sheet TiO{sub 2} grown on flat titanium surface without femtosecond laser structuring. The photocatalytic degradation of methyl orange reveals that photocatalytic efficiency of the hierarchical anatase 3D-TiO{sub 2} was improved by a maximum of 57% compared to that of nano-sheet TiO{sub 2} (55% vs 35%). Meanwhile, the hierarchical anatase 3D-TiO{sub 2} remained mechanically stable and constant in consecutive degradation cycles, which promises significance in practical application.

All-nanoparticle self-assembly ZnO/TiO₂ heterojunction thin films with remarkably enhanced photoelectrochemical activity.

Science.gov (United States)

Yuan, Sujun; Mu, Jiuke; Mao, Ruiyi; Li, Yaogang; Zhang, Qinghong; Wang, Hongzhi

2014-04-23

The multilaminated ZnO/TiO2 heterojunction films were successfully deposited on conductive substrates including fluorine-doped tin oxide (FTO) glass and flexible indium tin oxide coated poly(ethylene terephthalate) via the layer-by-layer (LBL) self assembly method from the oxide colloids without using any polyelectrolytes. The positively charged ZnO nanoparticles and the negatively charged TiO2 nanoparticles were directly used as the components in the consecutive deposition process to prepare the heterojunction thin films by varying the thicknesses. Moreover, the crystal growth of both oxides could be efficiently inhibited by the good connection between ZnO and TiO2 nanoparticles even after calcination at 500 °C, especially for ZnO which was able to keep the crystallite size under 25 nm. The as-prepared films were used as the working electrodes in the three-electrode photoelectrochemical cells. Because the well-contacted nanoscale heterojunctions were formed during the LBL self-assembling process, the ZnO/TiO2 all-nanoparticle films deposited on both substrates showed remarkably enhanced photoelectrochemical properties compared to that of the well-established TiO2 LBL thin films with similar thicknesses. The photocurrent response collected from the ZnO/TiO2 electrode on the FTO glass substrate was about five times higher than that collected from the TiO2 electrode. Owing to the absence of the insulating layer of dried polyelectrolytes, the ZnO/TiO2 all-nanoparticle heterojunction films were expected to be used in the photoelectrochemical device before calcination.

Enhanced supercapacitor performance using hierarchical TiO2 nanorod/Co(OH)2 nanowall array electrodes

International Nuclear Information System (INIS)

Ramadoss, Ananthakumar; Kim, Sang Jae

2014-01-01

Graphical abstract: - Highlights: • TiO 2 /Co(OH) 2 hierarchical nanostructure was prepared by a combination of hydrothermal and cathodic electrodeposition method. • Hierarchical nanostructure electrode exhibited a maximum capacitance of 274.3 mF cm −2 at a scan rate of 5 mV s −1 . • Combination of Co(OH) 2 nanowall with TiO 2 NR into a single system enhanced the electrochemical behavior of supercapacitor electrode. - Abstract: We report novel hierarchical TiO 2 nanorod (NR)/porous Co(OH) 2 nanowall array electrodes for high-performance supercapacitors fabricated using a two-step process that involves hydrothermal and electrodeposition techniques. Field-emission scanning electron microscope images reveal a bilayer structure consisting of TiO 2 NR arrays with porous Co(OH) 2 nanowalls. Compared with the bare TiO 2 NRs, the hierarchical TiO 2 NRs/Co(OH) 2 electrodes showed improved pseudocapacitive performance in a 2-M KOH electrolyte solution, exhibiting an areal specific capacitance of 274.3 mF cm −2 at a scan rate of 5 mV s −1 . The electrodes exhibited good stability, retaining 82.5% of the initial capacitance after 4000 cycles. The good pseudocapacitive performance of the hierarchical nanostructures is mainly due to the porous structure, which provides fast ion and electron transfer, a large surface area, short ion diffusion paths, and a favourable volume change during the cycling process

Hydrothermal synthesis and enhanced photocatalytic activity of mixed-phase TiO2 powders with controllable anatase/rutile ratio

Science.gov (United States)

Wang, Qi; Qiao, Zhi; Jiang, Peng; Kuang, Jianlei; Liu, Wenxiu; Cao, Wenbin

2018-03-01

In this study, mixed-phase TiO2 powders were novelly synthesized via a facile and mild hydrothermal method without any post-heat treatment. TiOSO4 and peroxide titanic acid (PTA) were used as inorganic titanium sources, while no special solvent or additive were introduced. The XRD and TEM results showed the mixed-phase TiO2 powders were composed of anatase and rutile phases, and the PTA sol played an important role on forming the rutile nucleus. The proportion of rutile in the mixed-phase TiO2 could be easily controlled in the range of 0%-70.5% by changing the amount of PTA sol used in the synthesis process. The UV-Visible absorption spectra indicated the prepared mixed-phase TiO2 showed enhanced visible light absorption with the increase of rutile ratio. The photodegradation experiments revealed the mixed-phase TiO2 exhibited the best photocatalytic activity at the rutile ratio of 41.5%, while a higher or lower rutile ratio both resulted in the decrease of photocatalytic activity.

Tm-doped TiO2 and Tm2Ti2O7 pyrochlore nanoparticles: enhancing the photocatalytic activity of rutile with a pyrochlore phase.

Science.gov (United States)

De Los Santos, Desiré M; Navas, Javier; Aguilar, Teresa; Sánchez-Coronilla, Antonio; Fernández-Lorenzo, Concha; Alcántara, Rodrigo; Piñero, Jose Carlos; Blanco, Ginesa; Martín-Calleja, Joaquín

2015-01-01

Tm-doped TiO2 nanoparticles were synthesized using a water-controlled hydrolysis reaction. Analysis was performed in order to determine the influence of the dopant concentration and annealing temperature on the phase, crystallinity, and electronic and optical properties of the resulting material. Various characterization techniques were utilized such as X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and UV-vis spectroscopy. For the samples annealed at 773 and 973 K, anatase phase TiO2 was obtained, predominantly internally doped with Tm(3+). ICP-AES showed that a doping concentration of up to 5.8 atom % was obtained without reducing the crystallinity of the samples. The presence of Tm(3+) was confirmed by X-ray photoelectron spectroscopy and UV-vis spectroscopy: the incorporation of Tm(3+) was confirmed by the generation of new absorption bands that could be assigned to Tm(3+) transitions. Furthermore, when the samples were annealed at 1173 K, a pyrochlore phase (Tm2Ti2O7) mixed with TiO2 was obtained with a predominant rutile phase. The photodegradation of methylene blue showed that this pyrochlore phase enhanced the photocatalytic activity of the rutile phase.

Facile synthesis of a conjugation-grafted-TiO2 nanohybrid with enhanced visible-light photocatalytic properties from nanotube titanic acid precursors

Science.gov (United States)

Guo, Yanru; Zhang, Min; Zhang, Zhihua; Li, Qiuye; Yang, Jianjun

2016-08-01

A conjugation-grafted-TiO2 nanohybrid was synthesized by chemically grafting conjugated structures on the surface of nanotube titanic acid (NTA) precursor-based TiO2 through the controlled thermal degradation of a coacervated polymer layer of polyvinyl alcohol (PVA). The interfacial interactions between the NTA precursor-based TiO2 and conjugated structures were characterized using Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Moreover, the effects of the NTA's pretreatment temperature and the weight ratio of NTA to PVA on the photocatalytic degradation of methyl orange were also investigated. A higher NTA pretreatment temperature and a lower NTA to PVA weight ratio were found to enhance photogenerated electron-hole separation efficiency and photocatalytic activity. Moreover, the conjugation-grafted-TiO2 nanohybrid synthesized from the NTA precursor displayed a much higher visible-light photocatalytic activity than that of the sample obtained from the P25 precursor. The origin of the enhanced photocatalytic activity under visible-light irradiation is also discussed in detail.

Enhancing the photocatalytic activity of nanocrystalline TiO2 by co-doping with fluorine and yttrium

International Nuclear Information System (INIS)

Zhang, Huarong; Miao, Guashuai; Ma, Xingping; Wang, Bei; Zheng, Haiwu

2014-01-01

Highlights: • (F, Y)-codoped TiO 2 nanoparticles were prepared by a simple sol–gel method. • The highest photocatalytic activity (15 times of that over the pure TiO 2 ) was exhibited in the codoped TiO 2 with 0.05% Y doping level. • The Y doping induced oxygen vancancies played a duel role on the photocatalyic activity of the codoped TiO 2 . • The photocatalytic reactive oxygen species are critical to the photocatalytic degradation processes. - Abstract: Fluorine and yttrium codoped TiO 2 nanoparticles were prepared using a simple sol–gel method. The products were characterized with various spectroscopic and analytical techniques to determine their structural, morphological, optical absorption and photocatalytic properties. The results reveal that neither F nor Y doping causes obvious absorption edge shift in TiO 2 . Photoluminescence (PL) emission spectra present that the PL signal is enhanced, suggesting a decrease of photo-generated charge carrier separation efficiency, after the F or Y doping. The synergistic action by the F and Y doping leads to the highest photocatalytic activity for the degradation of methylene blue solution in the 0.05% (F, Y)-codoped sample (15 times of that over the pure TiO 2 ). With the increase of Y doping level, the photocatalytic performance in the codoped samples increases firstly and then decreases. The photocatalytic activity variations after the F and Y doping were interpreted by the formation of photocatalytic reactive oxygen species induced by the dopings

Enhanced photochemical catalysis of TiO2 inverse opals by modification with ZnO or Fe2O3 using ALD and the hydrothermal method

Science.gov (United States)

Liu, Jiatong; Sun, Cuifeng; Fu, Ming; Long, Jie; He, Dawei; Wang, Yongsheng

2018-02-01

The development of porous materials exhibiting photon regulation abilities for improved photoelectrochemical catalysis performance is always one of the important goals of solar energy harvesting. In this study, methods to improve the photocatalytic activity of TiO2 inverse opals were discussed. TiO2 inverse opals were prepared by atomic layer deposition (ALD) using colloidal crystal templates. In addition, TiO2 inverse opal heterostructures were fabricated using colloidal heterocrystals by repeated vertical deposition using different colloidal spheres. The hydrothermal method and ALD were used to prepare ZnO- or Fe2O3-modified TiO2 inverse opals on the internal surfaces of the TiO2 porous structures. Although the photonic reflection band was not significantly varied by oxide modification, the presence of Fe2O3 in the TiO2 inverse opals enhanced their visible absorption. The conformally modified oxides on the TiO2 inverse opals could also form energy barriers and avoid the recombination of electrons and holes. The fabrication of the TiO2 photonic crystal heterostructures and modification with ZnO or Fe2O3 can enhance the photocatalytic activity of TiO2 inverse opals.

Heat transfer enhancement of TiO2/water nanofluid in a heat exchanger tube equipped with overlapped dual twisted-tapes

Directory of Open Access Journals (Sweden)

S. Eiamsa-ard

2015-09-01

Full Text Available Titanium dioxide (TiO2 in water as nanofluid was employed for heat transfer enhancement together with overlapped dual twisted tapes (O-DTs. The study encompassed Reynolds numbers from 5400 to 15,200, O-DTs with overlapped twist ratios (yo/y of 1.5, 2.0 and 2.5 and nanofluids with TiO2 volume concentrations (ϕ of 0.07%, 0.14% and 0.21%. The experimental and numerical results indicated that O-DTs with smaller overlapped twisted ratio delivered a stronger swirl intensity and higher turbulent kinetic energy (TKE. The use of O-DTs at the smallest overlapped twist ratio of 1.5 enhanced heat transfer rates up to 89%, friction factor by 5.43 times and thermal performance up to 1.13 times as compared to those of plain tube. In addition, heat transfer increased as TiO2 volume concentration of nanofluid increased, owing to the increases of contact surface and thermal conductivity. The simultaneous use of the O-DTs having twist ratios 1.5 with the nanofluid with TiO2 volume concentration of 0.21% resulted in heat transfer enhancement around 9.9–11.2% and thermal performance improvement up to 4.5% as compared to the use of O-DTs alone. The empirical correlations of heat transfer rate (Nu, friction factor (f and thermal performance (η in a constant wall heat flux tube equipped O-DTs at different overlapped twist ratios (yo/y and volume concentrations of TiO2 nanoparticles (ϕ are also reported for heat transfer applications.

Enhancing tribological performance of Ti-6Al-4V using pin on disc setup

Science.gov (United States)

Kumar, Deepak; Lijesh, K. P.; Deepak, K. B.; Kumar, Satish

2018-05-01

Titanium (Ti) alloy Ti-6Al-4V (Ti64), possesses a inimitable combination of mechanical, physical and corrosion properties, which makes them desirable for applications like aerospace, automobile, chemical and energy industries devices etc. However this alloy of Ti exhibits poor tribological (friction and wear) properties, which limits their full fledged implementation. However, the tribological behavior of T164 can be enhanced by providing a coating or a protective layer on it, which posses superior tribological properties. It is hypothesized that by a layer of alumina on the can be deposited on the surface of Ti64, by sliding them in dry-ambient condition using Pin On Disk (POD) machine. To validate the hypothesis, experiments were performed for different normal loading conditions of 13.7N, 68.7N and 109.9N at sliding speed of 0.01m/s and for a sliding distance of 1000m. The tribological performance of the experiments, were evaluated by measuring Coefficient of Friction (COF) and weight loss values. To understand the tribological mechanism and behaviour, In-situ analysis was performed on the pin using (i) Scanning Electron Microscopy (SEM) to understand the wear morphology, and (ii) Energy Dispersive Analysis of X Ray (EDAX) to estimate the deposition of alumina on surface of the pins. Based on the obtained results, the most favorable experimenting condition required for deposition of alumina over Ti64 will be identified. Finally, experiment on POD will be repeated for the selected experimenting condition and will be continued for the worst tribological condition. The obtained COF and wear values after performing the experiment will be presented.

Enhanced UV-Visible Light Photocatalytic Activity by Constructing Appropriate Heterostructures between Mesopore TiO₂ Nanospheres and Sn₃O₄ Nanoparticles.

Science.gov (United States)

Hu, Jianling; Tu, Jianhai; Li, Xingyang; Wang, Ziya; Li, Yan; Li, Quanshui; Wang, Fengping

2017-10-19

Novel TiO₂/Sn₃O₄ heterostructure photocatalysts were ingeniously synthesized via a scalable two-step method. The impressive photocatalytic abilities of the TiO₂/Sn₃O₄ sphere nanocomposites were validated by the degradation test of methyl orange and •OH trapping photoluminescence experiments under ultraviolet (UV) and visible light irradiation, respectively. Especially under the visible light, the TiO₂/Sn₃O₄ nanocomposites demonstrated a superb photocatalytic activity, with 81.2% of methyl orange (MO) decomposed at 30 min after irradiation, which greatly exceeded that of the P25 (13.4%), TiO₂ (0.5%) and pure Sn₃O₄ (59.1%) nanostructures. This enhanced photocatalytic performance could be attributed to the mesopore induced by the monodispersed TiO₂ cores that supply sufficient surface areas and accessibility to reactant molecules. This exquisite hetero-architecture facilitates extended UV-visible absorption and efficient photoexcited charge carrier separation.

Plasmon-resonance-enhanced visible-light photocatalytic activity of Ag quantum dots/TiO2 microspheres for methyl orange degradation

Science.gov (United States)

Yu, Xin; Shang, Liwei; Wang, Dongjun; An, Li; Li, Zhonghua; Liu, Jiawen; Shen, Jun

2018-06-01

We successfully prepared Ag quantum dots modified TiO2 microspheres by facile solvothermal and calcination method. The as-prepared Ag quantum dots/TiO2 microspheres were characterized by scanning electron microscope, transmission electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy and UV-vis diffuse reflectance spectroscopy. The Ag quantum dots/TiO2 photocatalyst showed excellent visible light absorption and efficient photocatalytic activity for methyl orange degradation. And the sample with the molar ratio of 0.05 (Ag to Ti) showed the best visible light photocatalytic activity for methyl orange degradation, mainly because of the surface plasmon resonance (SPR) effects of Ag quantum dots to generate electron and hole pairs for enhanced visible light photocatalysis. Finally, possible visible light photocatalytic mechanism of Ag quantum dots/TiO2 microspheres for methyl orange degradation was proposed in detail.

Significant enhancement in the photocatalytic activity of N, W co-doped TiO2 nanomaterials for promising environmental applications

International Nuclear Information System (INIS)

Thind, Sapanbir S; Wu Guosheng; Tian Min; Chen Aicheng

2012-01-01

In this work, a mesoporous N, W co-doped TiO 2 photocatalyst was synthesized via a one-step solution combustion method, which utilized urea as the nitrogen source and sodium tungstate as the tungsten source. The photocatalytic activity of the N, W co-doped TiO 2 photocatalyst was significantly enhanced by a facile UV pretreatment approach and was evaluated by measuring the rate of photodegradation of Rhodamine B under both UV and visible (λ > 420) light. Following the UV pretreatment, the UV photocatalytic activity of the N, W co-doped TiO 2 was doubled. In terms of visible light activity, the UV pretreatment resulted in an extraordinary >12 fold improvement. In order to gain insight into this substantial enhancement, the N, W co-doped TiO 2 photocatalysts were studied using x-ray diffraction, transmission electron microscopy, N 2 physisorption, UV–vis absorbance spectroscopy and x-ray photoelectron spectroscopy prior to and following the UV pretreatment. Our experimental results have revealed that this significant augmentation of photocatalytic activity may be attributed to several synergetic factors, including increase of the specific surface area, reduction of the band gap energy and the removal of carbon impurities. (paper)

Enhancement of mechanical strength in hot-pressed TiB2 composites by the addition of Fe and Ni

International Nuclear Information System (INIS)

Yen, C.F.; Yust, C.S.; Clark, G.W.

1978-01-01

Improvement in the fracture strength of TiB 2 composites through the addition of Fe and Ni is reported. Beam specimens containing up to 20 wt % of the metal component were fabricated by hot pressing above the eutectic temperature. Four point bending results indicated that the observed enhancement in strength was proportional to the vol % of the metal present. The results also revealed that TiB 2 --Ni composites have slightly better strength than TiB 2 --Fe samples at elevated temperatures, and that their strengths were consistently about twice that of pure TiB 2 . They also did not exhibit any serious degradation in strength up to 700 0 C. The fracture behavior was characterized using optical and scanning electron microscopy. The strengthening appears to be related to the presence of a metallic grain boundary phase between TiB 2 particles. The results further suggested that the formation of a special eutectic-like grain microstructure could render additional strengthening

Enhanced Efficiency of Dye-Sensitized Solar Cells with Mesoporous-Macroporous TiO2 Photoanode Obtained Using ZnO Template

Science.gov (United States)

Pham, Trang T. T.; Mathews, Nripan; Lam, Yeng-Ming; Mhaisalkar, Subodh

2017-06-01

Improved light harvesting efficiency can be achieved by enhancing the optical properties of the titanium dioxide (TiO2) photoanode in dye-sensitized solar cells (DSSCs), leading to higher power conversion efficiency. By incorporating submicrometer cavities in TiO2 mesoporous film, using zinc oxide (ZnO) particles as a template, a bimodal pore size structure has been created, called a mesoporous-macroporous nanostructure. This photoanode structure consists of 20-nm TiO2 nanoparticles with two kinds of pores with size of 20 nm (mesopores) and 500 nm (macropores). Energy-dispersive x-ray spectroscopy and x-ray diffraction studies showed no trace of ZnO in the TiO2 after removal by TiCl4 treatment. Higher diffuse transmittance of this film compared with the standard transparent photoanode provides evidence of improved light scattering. When employed in a device, the incident-photon-to-current efficiency of ZnO-assisted devices showed enhancement at longer wavelengths, corresponding to the Mie light scattering effect with the macropores as scattering centers. This resulted in overall higher power conversion efficiency of the DSSC. In this work, a nonvolatile gel ionic liquid was used as the electrolyte to also demonstrate the benefit of this structure in combination with a viscous electrolyte and its promising application to prolong the stability of DSSCs.

Solvothermal syntheses of Bi and Zn co-doped TiO{sub 2} with enhanced electron-hole separation and efficient photodegradation of gaseous toluene under visible-light

Energy Technology Data Exchange (ETDEWEB)

Li, Juan-Juan [Center for Excellence in Regional Atmospheric Environment, and Key Laboratory of Urban Pollutant Conversion, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Cai, Song-Cai [Center for Excellence in Regional Atmospheric Environment, and Key Laboratory of Urban Pollutant Conversion, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); University of Chinese Academy of Sciences, Beijing, 100049 (China); Xu, Zhen [Center for Excellence in Regional Atmospheric Environment, and Key Laboratory of Urban Pollutant Conversion, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Chen, Xi [Center for Excellence in Regional Atmospheric Environment, and Key Laboratory of Urban Pollutant Conversion, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); University of Chinese Academy of Sciences, Beijing, 100049 (China); Chen, Jin [Center for Excellence in Regional Atmospheric Environment, and Key Laboratory of Urban Pollutant Conversion, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Jia, Hong-Peng, E-mail: hpjia@iue.ac.cn [Center for Excellence in Regional Atmospheric Environment, and Key Laboratory of Urban Pollutant Conversion, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Chen, Jing, E-mail: jing.chen@fjirsm.ac.cn [State Key Laboratory of Structural Chemistry, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002 (China)

2017-03-05

Highlights: • Bi-Zn co-doped TiO{sub 2} catalysts were prepared by solvothermal route. • The incorporation of Bi doping into the TiO{sub 2} generates intermediate energy levels. • Bi and Zn doping showed the enhanced absorption in visible-light region. • Zn dopant acts as a mediator of interfacial charge transfer. • TiBi{sub 1.9%}Zn{sub 1%}O{sub 2} exhibited high photocatalytic degradation for toluene. - Abstract: This study investigated the effects of Bi doped and Bi-Zn co-doped TiO{sub 2} on photodegradation of gaseous toluene. The doped TiO{sub 2} with various concentration of metal was prepared using the solvothermal route and characterized by SEM, XRD, Raman, BET, DRS, XPS, PL and EPR. Their photocatalytic activities under visible-light irradiation were drastically influenced by the dopant content. The results showed that moderate metal doping levels were obviously beneficial for the toluene degradation, while high doping levels suppressed the photocatalytic activity. The photocatalytic degradation of toluene over TiBi{sub 1.9%}O{sub 2} and TiBi{sub 1.9%}Zn{sub 1%}O{sub 2} can reach to 51% and 93%, respectively, which are much higher than 25% of TiO{sub 2}. Bi doping into TiO{sub 2} lattice generates new intermediate energy level of Bi below the CB edge of TiO{sub 2}. The electron excitation from the VB to Bi orbitals results in the decreased band gap, extended absorption of visible-light and thus enhances its photocatalytic efficiency. Zn doping not only further enhances the absorption in this visible-light region, but also Zn dopant exists as the form of ZnO crystallites located on the interfaces of TiO{sub 2} agglomerates and acts as a mediator of interfacial charge transfer to suppress the electron-hole recombination. These synergistic effects are responsible for the enhanced photocatalytic performance.

Facile synthesis of the Ti3+ self-doped TiO2-graphene nanosheet composites with enhanced photocatalysis.

Science.gov (United States)

Qiu, Bocheng; Zhou, Yi; Ma, Yunfei; Yang, Xiaolong; Sheng, Weiqin; Xing, Mingyang; Zhang, Jinlong

2015-02-26

This study developed a facile approach for preparing Ti(3+) self-doped TiO2-graphene photocatalyst by a one-step vacuum activation technology involved a relative lower temperature, which could be activated by the visible light owing to the synergistic effect among Ti(3+) doping, some new intersurface bonds generation and graphene oxide reduction. Compared with the traditional methods, the vacuum activation involves a low temperature and low-costing, which can achieve the reduction of GO, the self doping of Ti(3+) in TiO2 and the loading of TiO2 nanoparticles on GR surface at the same time. These resulting TiO2-graphene composites show the high photodegradation rate of MO, high hydrogen evolution activity and excellent IPCE in the visible light irradiation. The facile vacuum activation method can provide an effective and practical approach to improve the performance of TiO2-graphene and other metal oxides-graphene towards their practical photocatalytic applications.

Evidence for lattice-polarization-enhanced field effects at the SrTiO₃-based heterointerface

DEFF Research Database (Denmark)

Li, Y.; R. Zhang, H.; Lei, Y.

2016-01-01

Electrostatic gating provides a powerful approach to tune the conductivity of the two-dimensionalelectron liquid between two insulating oxides. For the LaAlO3/SrTiO3 (LAO/STO) interface, suchgating effect could be further enhanced by a strong lattice polarization of STO caused by simultaneousappl......Electrostatic gating provides a powerful approach to tune the conductivity of the two-dimensionalelectron liquid between two insulating oxides. For the LaAlO3/SrTiO3 (LAO/STO) interface, suchgating effect could be further enhanced by a strong lattice polarization of STO caused...... expansion of the out-of-plane lattice of STO. Photo excitation affects the polarizationprocess by accelerating the field-induced lattice expansion. The present work demonstrates the greatpotential of combined stimuli in exploring emergent phenomenon at complex oxide interfaces....

Study on the enhanced adsorption properties of lysozyme on polyacrylic acid modified TiO2 nano-adsorbents

Science.gov (United States)

Liu, Yufeng; Jin, Zu; Meng, Hao; Zhang, Xia

2018-01-01

The adsorption and immobilization of enzymes onto solid carriers has been focused on due to their many advantages, such as improved stability against a thermal or organic solvent and a good cycle usability. TiO2 nanoparticles is one of excellent nano-adsorbents owing to its excellent biocompatibility, non-inflammatory, and abundant surface hydroxyl groups, which are convenient to be combined with various functional groups. In this paper polyacrylic acid (PAA) modified TiO2 nanoparticles were synthesized through an in situ light-induced polymerization of acrylic acid on the surface of TiO2 nanoparticles. The structure and surface physicochemical properties of the PAA/TiO2 nanoparticles were characterized by TEM, XRD, FT-IR, Zeta potential measurements and TG-DSC. The experimental results showed that the isoelectric point of PAA/TiO2 significantly reduced to 1.82 compared with that of pure TiO2 nanoparticles (6.08). In the adsorption tests of lysozyme (Lyz), the PAA/TiO2 nanoparticles displayed enhanced adsorption activity compared with pristine TiO2. The maximum adsorption capacity of PAA/TiO2 for Lyz was 225.9 mg g-1 under the optimum conditions where the initial concentration of Lyz was 300 mg ml-1, the addition amount of PAA/TiO2 was 6.4 mg, the adsorption time was 30 min and the pH value was 7.0. The sodium dodecyl sulfate (SDS, 0.5%) presented the best efficiency (76.86%) in the removal of adsorbed Lyz, and the PAA/TiO2 nanoparticles showed excellent adsorption stability based on five cyclic adsorption-desorption tests. The fitting calculation results of the adsorption isotherm and the thermodynamics indicated the adsorption was an exothermic, entropy increasing, spontaneous and monomolecular layer adsorption process.

Synthesis of NaOH-Modified TiOF2 and Its Enhanced Visible Light Photocatalytic Performance on RhB

Directory of Open Access Journals (Sweden)

Chentao Hou

2017-08-01

Full Text Available NaOH-modified TiOF2 was successfully prepared using a modified low-temperature hydrothermal method. Scanning electron microscopy shows that NaOH-modified TiOF2 displayed a complex network shape with network units of about 100 nm. The structures of NaOH-modified TiOF2 have not been reported elsewhere. The network shape permits the NaOH-modified TiOF2 a SBET of 36 m2∙g−1 and a pore diameter around 49 nm. X-ray diffraction characterization shows that TiOF2 and NaOH-modified TiOF2 are crystallized with a pure changed cubic phase which accords with the SEM results. Fourier transform infrared spectroscopy characterization shows that NaOH-modified TiOF2 has more O–H groups to supply more lone electron pairs to transfer from O of O–H to Ti and O of TiOF2. UV–vis diffuse reflectance spectroscopy (DRS shows that the NaOH-modified TiOF2 sample has an adsorption plateau rising from 400 to 600 nm in comparison with TiOF2, and its band gap is 2.62 eV, lower than that of TiOF2. Due to the lower band gap, more O–H groups adsorption, network morphologies with larger surface area, and sensitization progress, the NaOH-modified TiOF2 exhibited much higher photocatalytic activity for Rhodamine B (RhB degradation. In addition, considering the sensitization progress, O–H groups on TiOF2 not only accelerated the degradation rate of RhB, but also changed its degradation path. As a result, the NaOH-modified TiOF2 exhibited much higher photocatalytic activity for RhB degradation than the TiOF2 in references under visible light. This finding provides a new idea to enhance the photocatalytic performance by NaOH modification of the surface of TiOF2.

Internal Quality Assurance--Enhancing Quality Culture. ENQA Workshop Report 16

Science.gov (United States)

ENQA (European Association for Quality Assurance in Higher Education), 2010

2010-01-01

The European Association for Quality Assurance in Higher Education (ENQA), in cooperation with the Quality Assurance Agency (QAA, UK), organised a seminar on theme "Internal Quality Assurance--Enhancing quality culture" which was held on 8-9 June, 2010 in London, United Kingdom. The seminar marked the fourth annual meeting of the ENQA…

Plasmon resonance enhanced photocatalysis under visible light with Au/Cu-TiO2 nanoparticles: Removal Cr (VI) from water as a case of study

KAUST Repository

Gondal, M. A.; Dastageer, Mohamed Abdulkader; Rashid, Shama G.; Zubair, Syed M.; Ali, Mohammada A.; Anjum, Dalaver H.; Lienhard V, John H.; McKinley, Gareth H.; Varanasi, Kripa K.

2013-01-01

Gold modified copper doped titania (Au/Cu:TiO2) nanoparticles were synthesized by a modified sol gel method and characterized using XRD, optical and TEM based techniques. The as-prepared material contained anatase phase particles with quasi-spherical morphology, showing enhanced absorption in the visible region and low photoluminescence emission intensity. Photocatalytic reduction of Cr (VI) in aqueous suspension with the Au/Cu:TiO2catalyst under 532 nm laser radiation and a visible broad band lamp source yielded 96% and 45% removal, respectively, without any additives. The enhanced photocatalytic activity can be attributed to the improved plasmonic effect due to gold modification and the expanded visible absorption due to copper doping. Moreover a comparative study of the material properties and catalytic activity of TiO2, Cu-TiO2and Au/Cu-TiO2 was carried out. © 2013 by American Scientific Publishers.

Plasmon resonance enhanced photocatalysis under visible light with Au/Cu-TiO2 nanoparticles: Removal Cr (VI) from water as a case of study

KAUST Repository

Gondal, M. A.

2013-12-01

Gold modified copper doped titania (Au/Cu:TiO2) nanoparticles were synthesized by a modified sol gel method and characterized using XRD, optical and TEM based techniques. The as-prepared material contained anatase phase particles with quasi-spherical morphology, showing enhanced absorption in the visible region and low photoluminescence emission intensity. Photocatalytic reduction of Cr (VI) in aqueous suspension with the Au/Cu:TiO2catalyst under 532 nm laser radiation and a visible broad band lamp source yielded 96% and 45% removal, respectively, without any additives. The enhanced photocatalytic activity can be attributed to the improved plasmonic effect due to gold modification and the expanded visible absorption due to copper doping. Moreover a comparative study of the material properties and catalytic activity of TiO2, Cu-TiO2and Au/Cu-TiO2 was carried out. © 2013 by American Scientific Publishers.

Synthesis and characterization of ZnO and TiO2 hollow spheres with enhanced photoreactivity

International Nuclear Information System (INIS)

Li Xiaofang; Lv Kangle; Deng Kejian; Tang Junfeng; Su Rong; Sun Jie; Chen Lianqing

2009-01-01

To study the relationship between the morphology and the photoreactivity of the catalyst, hollow spheres of two semiconductors of ZnO and TiO 2 were synthesized by using sulfonated polystyrene (PS) as template. The catalyst samples were then characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), diffuse reflectance spectra (DRS), transmission electron microscopy (TEM) and N 2 sorption. Reactive brilliant red X3B, an anionic organic dye, was used in this study as a model chemical with the aim of organic pollutants control. The results show that, whatever the catalyst was, both the adsorptive ability and photoreactivity of the hollow spheres were much higher than that of nanoparticles. The adsorption and photoreactivity of ZnO hollow spheres increased by a factor of 7.36 and 4.66, respectively compared with ZnO nanoparticles, while 3.74 times increased in adsorption and 3.41 times increased in photoreactivity for TiO 2 hollow spheres compared with TiO 2 nanoparticles. Correlations between adsorption and photoreactivity reflected the importance of adsorption in the enhanced photoreactivity of ZnO and TiO 2 hollow spheres

Mixed-matrix membranes with enhanced antifouling activity: probing the surface-tailoring potential of Tiron and chromotropic acid for nano-TiO2

Science.gov (United States)

Pal, Avishek; Dey, T. K.; Debnath, A. K.; Bhushan, Bharat; Sahu, A. K.; Bindal, R. C.; Kar, Soumitra

2017-09-01

Mixed-matrix membranes (MMMs) were developed by impregnating organofunctionalized nanoadditives within fouling-susceptible polysulfone matrix following the non-solvent induced phase separation (NIPS) method. The facile functionalization of nanoparticles of anatase TiO2 (nano-TiO2) by using two different organoligands, viz. Tiron and chromotropic acid, was carried out to obtain organofunctionalized nanoadditives, FT-nano-TiO2 and FC-nano-TiO2, respectively. The structural features of nanoadditives were evaluated by X-ray diffraction, X-ray photoelectron spectroscopy, Raman and Fourier transform infrared spectroscopy, which established that Tiron leads to the blending of chelating and bridging bidentate geometries for FT-nano-TiO2, whereas chromotropic acid produces bridging bidentate as well as monodentate geometries for FC-nano-TiO2. The surface chemistry of the studied membranes, polysulfone (Psf): FT-nano-TiO2 UF and Psf: FC-nano-TiO2 UF, was profoundly influenced by the benign distributions of the nanoadditives enriched with distinctly charged sites (-SO3 -H+ ), as evidenced by superior morphology, improved topography, enhanced surface hydrophilicity and altered electrokinetic features. The membranes exhibited enhanced solvent throughputs, viz. 3500-4000 and 3400-4300 LMD at 1 bar of transmembrane pressure, without significant compromise in their rejection attributes. The flux recovery ratios and fouling resistive behaviours of MMMs towards bovine serum albumin indicated that the nanoadditives could impart stable and appreciable antifouling activity, potentially aiding in a sustainable ultrafiltration performance.

Mixed-matrix membranes with enhanced antifouling activity: probing the surface-tailoring potential of Tiron and chromotropic acid for nano-TiO2.

Science.gov (United States)

Pal, Avishek; Dey, T K; Debnath, A K; Bhushan, Bharat; Sahu, A K; Bindal, R C; Kar, Soumitra

2017-09-01

Mixed-matrix membranes (MMMs) were developed by impregnating organofunctionalized nanoadditives within fouling-susceptible polysulfone matrix following the non-solvent induced phase separation (NIPS) method. The facile functionalization of nanoparticles of anatase TiO 2 (nano-TiO 2 ) by using two different organoligands, viz . Tiron and chromotropic acid, was carried out to obtain organofunctionalized nanoadditives, F T -nano-TiO 2 and F C -nano-TiO 2 , respectively. The structural features of nanoadditives were evaluated by X-ray diffraction, X-ray photoelectron spectroscopy, Raman and Fourier transform infrared spectroscopy, which established that Tiron leads to the blending of chelating and bridging bidentate geometries for F T -nano-TiO 2 , whereas chromotropic acid produces bridging bidentate as well as monodentate geometries for F C -nano-TiO 2 . The surface chemistry of the studied membranes, polysulfone (Psf): F T -nano-TiO 2 UF and Psf: F C -nano-TiO 2 UF, was profoundly influenced by the benign distributions of the nanoadditives enriched with distinctly charged sites ([Formula: see text]), as evidenced by superior morphology, improved topography, enhanced surface hydrophilicity and altered electrokinetic features. The membranes exhibited enhanced solvent throughputs, viz . 3500-4000 and 3400-4300 LMD at 1 bar of transmembrane pressure, without significant compromise in their rejection attributes. The flux recovery ratios and fouling resistive behaviours of MMMs towards bovine serum albumin indicated that the nanoadditives could impart stable and appreciable antifouling activity, potentially aiding in a sustainable ultrafiltration performance.

Porous TiO{sub 2} nanofibers decorated CdS nanoparticles by SILAR method for enhanced visible-light-driven photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Tian, Fengyu; Hou, Dongfang, E-mail: dfhouok@126.com; Hu, Fuchao; Xie, Kui; Qiao, Xiuqing; Li, Dongsheng, E-mail: lidongsheng1@126.com

2017-01-01

Graphical abstract: A heterojunction photocatalyst with CdS Nanoparticles self-assembled via SILAR Method at surfaces of electrospun TiO2 nanofibers shows enhanced visible-light photocatalytic activities. - Highlights: • Combined electrospinning and successive ionic layer adsorption and reaction process. • Pouous TiO{sub 2} nanofibers decorated CdS nanoparticles. • Synergetic effect of photosensitization and heterojunction. - Abstract: 1D porous CdS nanoparticles/TiO{sub 2} nanofibers heterostructure has been fabricated via simple electrospinning and a successive ionic layer adsorption and reaction (SILAR) process. The morphology, composition, and optical properties of the resulting CdS/TiO{sub 2} heterostructures can be rationally tailored through changing the SILAR cycles. The photocatalytic hydrogen evolution and decomposition of rhodamine B (RhB) of the as-synthesized heterostructured photocatalysts were investigated under visible light irradiation. Compared to TiO{sub 2} nanofibers，the as-obtained CdS/TiO{sub 2} heterostructures exhibit enhanced photocatalytic activity for hydrogen production and decomposition of RhB under visible-light irradiation. The heterojunction system performs best with H{sub 2} generation rates of 678.61 μmol h{sup −1} g{sup −1} under visible light irradiation which benefits from the two effects: (a) the 1D porous nanofibrous morphology contributes to not only more active sites but also more efficient transfer of the photogenerated charges (b) the synergetic effect of heterojunction and photosensitization reducing the recombination of photogenerated electrons and holes.

Enhanced photoelectrochemical efficiency and stability using a conformal TiO2 film on a black silicon photoanode

Science.gov (United States)

Yu, Yanhao; Zhang, Zheng; Yin, Xin; Kvit, Alexander; Liao, Qingliang; Kang, Zhuo; Yan, Xiaoqin; Zhang, Yue; Wang, Xudong

2017-06-01

Black silicon (b-Si) is a surface-nanostructured Si with extremely efficient light absorption capability and is therefore of interest for solar energy conversion. However, intense charge recombination and low electrochemical stability limit the use of b-Si in photoelectrochemical solar-fuel production. Here we report that a conformal, ultrathin, amorphous TiO2 film deposited by low-temperature atomic layer deposition (ALD) on top of b-Si can simultaneously address both of these issues. Combined with a Co(OH)2 thin film as the oxygen evolution catalyst, this b-Si/TiO2/Co(OH)2 heterostructured photoanode was able to produce a saturated photocurrent density of 32.3 mA cm-2 at an external potential of 1.48 V versus reversible reference electrode (RHE) in 1 M NaOH electrolyte. The enhanced photocurrent relative to planar Si and unprotected b-Si photoelectrodes was attributed to the enhanced charge separation efficiency as a result of the effective passivation of defective sites on the b-Si surface. The 8-nm ALD TiO2 layer extends the operational lifetime of b-Si from less than half an hour to four hours.

Student Engagement in the Scottish Quality Enhancement Framework

Science.gov (United States)

Gvaramadze, Irakli

2011-01-01

The research addressed the interplay of student engagement and quality enhancement mechanisms in the Scottish higher education system. The paper demonstrates increasing focus on student learning, learning experience and high-quality learning in the current quality enhancement approaches. The student-university coproduction model is used to…

Coaxial nanofibers containing TiO2 in the shell for water treatment applications

Science.gov (United States)

Kizildag, N.; Geltmeyer, J.; Ucar, N.; De Buysser, K.; De Clerck, K.

2017-10-01

In recent years, the basic electrospinning setup has undergone many modifications carried out to enhance the quality and improve the functionality of the resulting nanofibers. Being one of these modifications, coaxial electrospinning has attracted great attention. It enables to use different materials in nanofiber production and produce multi-layered and functional nanofibers in one step. In this study, TiO2 has been added to the shell layer of coaxial nanofibers to develop functional nanofibers which may be used in water treatment applications. The coaxial nanofibers containing TiO2 in the shell layer are compared to uniaxial nanofibers containing TiO2 in bulk fiber structure, regarding their morphology and photocatalytic activity. Uniform uniaxial and coaxial nanofibers with TiO2 were obtained. The average nanofiber diameter of coaxial nanofibers were higher. Coaxial nanofibers, which contained lower amount of TiO2, displayed similar performance to uniaxial nanofibers with TiO2 in terms of photocatalytic degradation ability against isoproturon.

Fabrication of novel Ag−TiO_2 nanobelts as a photoanode for enhanced photovoltage performance in dye sensitized solar cells

International Nuclear Information System (INIS)

Wang, Yang; Li, Zhen; Cao, Ya; Li, Fei; Zhao, Wen; Liu, Xueqin; Yang, Jianbo

2016-01-01

TiO_2 nanobelts (TiO_2NBs) were successfully prepared using a solvothermal route via Ti foil as substrate in large scales. The morphology evolution process and formation mechanism of the as-obtained products were investigated in detail. On the basis of this novel structure, chemical sensitive Ag modified TiO_2NBs nanocomposites (Ag−TiO_2NBs) were fabricated. It was found that Ag−TiO_2NBs exhibit strong light absorption and efficient electron transport. According to Mott-Schottky analysis, Ag−TiO_2NBs show less surface trapping sites compared with TiO_2NBs. The Ag−TiO_2NBs photoanode fabricated in 0.01 M AgNO_3 demonstrates the best performance with a short-circuit current of 11.9 mA cm"−"2 corresponding to a photoelectric conversion efficiency of 4.89%, which is higher than that of pure TiO_2NBs based solar cell by 60%. - Graphical abstract: J-V curves of DSSCs based on TiO_2NPs, TiO_2NBs and Ag−TiO_2NBs—X under AM 1.5 conditions (100 mW cm"−"2). Ag−TiO_2NBs nanocomposites were prepared via a simple and effective method. Owing to strong light absorption and efficient electron transport, Ag−TiO_2NBs—0.01 M shows a PCE of 4.89% when prepared as a photoanode in DSSCs. - Highlights: • A facile route was adopted to construct well-dispersed Ag nanoparticles on TiO_2 nanobelts (Ag—TiO_2NBs). • Structure and photoelectrochemical properties of Ag—TiO_2NBs were studied. • Ag nanoparticles were found to modify the defects of TiO_2NBs. • Enhanced photovoltaic property of Ag—TiO_2NBs, compared to TiO_2NBs.

Au Nanoclusters Sensitized Black TiO2-x Nanotubes for Enhanced Photodynamic Therapy Driven by Near-Infrared Light.

Science.gov (United States)

Yang, Dan; Gulzar, Arif; Yang, Guixin; Gai, Shili; He, Fei; Dai, Yunlu; Zhong, Chongna; Yang, Piaoping

2017-12-01

The low reactive oxygen species production capability and the shallow tissue penetration of excited light (UV) are still two barriers in photodynamic therapy (PDT). Here, Au cluster anchored black anatase TiO 2- x nanotubes (abbreviated as Au 25 /B-TiO 2- x NTs) are synthesized by gaseous reduction of anatase TiO 2 NTs and subsequent deposition of noble metal. The Au 25 /B-TiO 2- x NTs with thickness of about 2 nm exhibit excellent PDT performance. The reduction process increased the density of Ti 3+ on the surface of TiO 2 , which effectively depresses the recombination of electron and hole. Furthermore, after modification of Au 25 nanoclusters, the PDT efficiency is further enhanced owing to the changed electrical distribution in the composite, which forms a shallow potential well on the metal-TiO 2 interface to further hamper the recombination of electron and hole. Especially, the reduction of anatase TiO 2 can expend the light response range (UV) of TiO 2 to the visible and even near infrared (NIR) light region with high tissue penetration depth. When excited by NIR light, the nanoplatform shows markedly improved therapeutic efficacy attributed to the photocatalytic synergistic effect, and promotes separation or restrained recombination of electron and hole, which is verified by experimental results in vitro and in vivo. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Direct observation of oxygen-vacancy-enhanced polarization in a SrTiO{sub 3}-buffered ferroelectric BaTiO{sub 3} film on GaAs

Energy Technology Data Exchange (ETDEWEB)

Qiao, Qiao [Department of Physics, University of Illinois at Chicago, Chicago, Illinois 60607 (United States); Department of Physics and Astronomy, Vanderbilt University, Nashville, Tennessee 37240 (United States); Materials Science and Technology Department, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Zhang, Yuyang [Department of Physics and Astronomy, Vanderbilt University, Nashville, Tennessee 37240 (United States); Materials Science and Technology Department, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Contreras-Guerrero, Rocio; Droopad, Ravi [Ingram School of Engineering, Texas State University, San Marcos, Texas 78666 (United States); Pantelides, Sokrates T. [Department of Physics and Astronomy, Vanderbilt University, Nashville, Tennessee 37240 (United States); Materials Science and Technology Department, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Department of Electrical Engineering and Computer Science, Vanderbilt University, Nashville, Tennessee 37240 (United States); Pennycook, Stephen J. [Department of Materials Science and Engineering, National University of Singapore, Singapore 117575 (Singapore); Ogut, Serdar; Klie, Robert F. [Department of Physics, University of Illinois at Chicago, Chicago, Illinois 60607 (United States)

2015-11-16

The integration of functional oxide thin-films on compound semiconductors can lead to a class of reconfigurable spin-based optoelectronic devices if defect-free, fully reversible active layers are stabilized. However, previous first-principles calculations predicted that SrTiO{sub 3} thin films grown on Si exhibit pinned ferroelectric behavior that is not switchable, due to the presence of interfacial vacancies. Meanwhile, piezoresponse force microscopy measurements have demonstrated ferroelectricity in BaTiO{sub 3} grown on semiconductor substrates. The presence of interfacial oxygen vacancies in such complex-oxide/semiconductor systems remains unexplored, and their effect on ferroelectricity is controversial. Here, we use a combination of aberration-corrected scanning transmission electron microscopy and first-principles density functional theory modeling to examine the role of interfacial oxygen vacancies on the ferroelectric polarization of a BaTiO{sub 3} thin film grown on GaAs. We demonstrate that interfacial oxygen vacancies enhance the polar discontinuity (and thus the single domain, out-of-plane polarization pinning in BaTiO{sub 3}), and propose that the presence of surface charge screening allows the formation of switchable domains.

Enhanced photomechanical response of a Ni-Ti shape memory alloy coated with polymer-based photothermal composites

Science.gov (United States)

Perez-Zúñiga, M. G.; Sánchez-Arévalo, F. M.; Hernández-Cordero, J.

2017-10-01

A simple way to enhance the activation of shape memory effects with light in a Ni-Ti alloy is demonstrated. Using polydimethylsiloxane-carbon nanopowder (PDMS+CNP) composites as coatings, the one-way shape memory effect (OWSME) of the alloy can be triggered using low power IR light from a laser diode. The PDMS+CNP coatings serve as photothermal materials capable to absorb light, and subsequently generate and dissipate heat in a highly efficient manner, thereby reducing the optical powers required for triggering the OWSME in the Ni-Ti alloy. Experimental results with a cantilever flexural test using both, bare Ni-Ti and coated samples, show that the PDMS+CNP coatings perform as thermal boosters, and therefore the temperatures required for phase transformation in the alloy can be readily obtained with low laser powers. It is also shown that the two-way shape memory effect (TWSME) can be set in the Ni-Ti alloy through cycling the TWSME by simply modulating the laser diode signal. This provides a simple means for training the material, yielding a light driven actuator capable to provide forces in the mN range. Hence, the use of photothermal coatings on Ni-Ti shape memory alloys may offer new possibilities for developing light-controlled smart actuators.

Simple fabrication of TiO2/C nanocomposite with enhanced electrochemical performance for lithium-ion batteries

International Nuclear Information System (INIS)

Bai, Xue; Li, Tao; Qi, Yong-Xin; Gao, Xue-Ping; Yin, Long-Wei; Li, Hui; Zhu, Hui-Ling; Lun, Ning; Bai, Yu-Jun

2015-01-01

TiO 2 /C nanocomposites were fabricated by simple hydrolysis of tetrabutyl titanate to yield TiO 2 nanoparticles followed by carbonizing the mixture of glucose and TiO 2 at 600 °C. By merely varying the weight ratio of glucose:TiO 2 , the electrochemical performance of the composites could be optimized significantly. At a ratio of 0.8, the composite exhibits a high reversible capacity of 283.7 mA h g −1 after cycling 100 times at a current density of 100 mA g −1 , as well as the capacities of 245.1, 213.6, 179.9 and 136.6 mA h g −1 at the corresponding densities of 200, 400, 800 and 1600 mA g −1 . After cycling 1000 times at 500 mA g −1 , a capacity of 122.8 mA h g −1 was retained for the composite with a ratio of 0.8, and even a capacity of 149.1 mA h g −1 for the composite with a ratio of 0.7. The enhanced performance is ascribed to the carbon-coated TiO 2 nanoparticles uniformly embedding in the carbon matrix with appropriate carbon content

Enhanced Charge Extraction of Li-Doped TiO₂ for Efficient Thermal-Evaporated Sb₂S₃ Thin Film Solar Cells.

Science.gov (United States)

Lan, Chunfeng; Luo, Jingting; Lan, Huabin; Fan, Bo; Peng, Huanxin; Zhao, Jun; Sun, Huibin; Zheng, Zhuanghao; Liang, Guangxing; Fan, Ping

2018-02-28

We provided a new method to improve the efficiency of Sb₂S₃ thin film solar cells. The TiO₂ electron transport layers were doped by lithium to improve their charge extraction properties for the thermal-evaporated Sb₂S₃ solar cells. The Mott-Schottky curves suggested a change of energy band and faster charge transport in the Li-doped TiO₂ films. Compared with the undoped TiO₂, Li-doped mesoporous TiO₂ dramatically improved the photo-voltaic performance of the thermal-evaporated Sb₂S₃ thin film solar cells, with the average power conversion efficiency ( PCE ) increasing from 1.79% to 4.03%, as well as the improved open-voltage ( V oc ), short-circuit current ( J sc ) and fill factors. The best device based on Li-doped TiO₂ achieved a power conversion efficiency up to 4.42% as well as a V oc of 0.645 V, which are the highest values among the reported thermal-evaporated Sb₂S₃ solar cells. This study showed that Li-doping on TiO₂ can effectively enhance the charge extraction properties of electron transport layers, offering a new strategy to improve the efficiency of Sb₂S₃-based solar cells.

Enhanced Visible Light Photocatalytic Activity of V2O5 Cluster Modified N-Doped TiO2 for Degradation of Toluene in Air

Directory of Open Access Journals (Sweden)

Fan Dong

2012-01-01

Full Text Available V2O5 cluster-modified N-doped TiO2 (N-TiO2/V2O5 nanocomposites photocatalyst was prepared by a facile impregnation-calcination method. The effects of V2O5 cluster loading content on visible light photocatalytic activity of the as-prepared samples were investigated for degradation of toluene in air. The results showed that the visible light activity of N-doped TiO2 was significantly enhanced by loading V2O5 clusters. The optimal V2O5 loading content was found to be 0.5 wt.%, reaching a removal ratio of 52.4% and a rate constant of 0.027 min−1, far exceeding that of unmodified N-doped TiO2. The enhanced activity is due to the deposition of V2O5 clusters on the surface of N-doped TiO2. The conduction band (CB potential of V2O5 (0.48 eV is lower than the CB level of N-doped TiO2 (−0.19 V, which favors the photogenerated electron transfer from CB of N-doped TiO2 to V2O5 clusters. This function of V2O5 clusters helps promote the transfer and separation of photogenerated electrons and holes. The present work not only displays a feasible route for the utilization of low cost V2O5 clusters as a substitute for noble metals in enhancing the photocatalysis but also demonstrates a facile method for preparation of highly active composite photocatalyst for large-scale applications.

Enhanced photocatalytic activity towards degradation and H{sub 2} evolution over one dimensional TiO{sub 2}@MWCNTs heterojunction

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xiao [CAS Key Laboratory of Standardization and Measurement for Nanotechnology, CAS Center for Excellence in Nanoscience, National Center for Nanoscience and Technology, Beijing 100190 (China); Key Laboratory of Luminescence and Optical Information of the Ministry of Education Institute of Optoelectronics Technology, Beijing Jiaotong University, Beijing 100044 (China); Cao, Shuang; Wu, Zhijiao [CAS Key Laboratory of Standardization and Measurement for Nanotechnology, CAS Center for Excellence in Nanoscience, National Center for Nanoscience and Technology, Beijing 100190 (China); Zhao, Suling, E-mail: slzhao@bjtu.edu.cn [Key Laboratory of Luminescence and Optical Information of the Ministry of Education Institute of Optoelectronics Technology, Beijing Jiaotong University, Beijing 100044 (China); Piao, Lingyu, E-mail: piaoly@nanoctr.cn [CAS Key Laboratory of Standardization and Measurement for Nanotechnology, CAS Center for Excellence in Nanoscience, National Center for Nanoscience and Technology, Beijing 100190 (China)

2017-04-30

Highlights: • One dimensional TiO{sub 2}@MWCNTs core-shell photocatalyst constructed. • The TiO{sub 2} nanoparticles are highly dispersed on the MWCNTs. • The layer thickness adjusted for different nanocomposites. • The 1D heterojunction enhancing electron transfers. - Abstract: With the distinct electronic and optical properties, multiwall carbon nanotubes (MWCNTs) are identified as an outstanding catalyst support, which can effectively improve the performance of the TiO{sub 2} photocatalysts. Herein, the unique one dimensional TiO{sub 2}@MWCNTs nanocomposites have been prepared by a facile hydrothermal method. The TiO{sub 2} coating layers are extremely uniform and the thickness is adjustable for different nanocomposites. XPS measurements confirm that intimate electronic interactions are existed between MWCNTs and TiO{sub 2} via interfacial Ti−O−C bond and the photoluminescence intensity of the TiO{sub 2}@MWCNTs nanocomposites are effectively quenched compared with pure TiO{sub 2}, suggesting the fast electron transfer rates. The thickness of TiO{sub 2} coating layers of the TiO{sub 2}@MWCNTs nanocomposites plays a significant role in the photocatalytic degradation of organic pollutants, such as methylene blue (MB) and Rhodamine B (RhB), and photocatalytic H{sub 2} evolution from water. Due to the formation of one dimensional heterojunction of TiO{sub 2}@MWCNTs nanocomposites and the positive synergistic effect between TiO{sub 2} and carbon nanotubes, it is found that the photocatalytic activity of the system is significantly improved.

One-pot engineering TiO2/graphene interface for enhanced adsorption and photocatalytic degradation of multiple organics.

Science.gov (United States)

Song, Jianhua; Ling, Yun; Xie, Yu; Liu, Lianjun; Zhu, Huihua

2018-06-13

It is challenging to design a multifunctional structure or composite for simultaneously adsorb and photocatalytic degrade organic pollutants in water. Towards this goal, this work innovatively engineered interfacial sites between TiO2 particles and reduced graphene oxide (RGO) sheets by employing in situ one-pot one-step solvothermal method. The interface was associated with the content of RGO, solvothermal time and solvent ratio of n-pentanol to n-hexane. It was found that when at a moderate amount of RGO (25%), TiO2 nanoparticles were well dispersed on the surface of RGO or wrapped by RGO, thus leading to a fully contact and strong interaction to form Ti - O - C interfacial structure. But when at a low content of RGO (6%), TiO2 aggregates were mixture of nanosheets, nanoparticles and nanorods. 25%RGO/TiO2 also had 175% higher surface area (146m2/g), 95% larger volume (0.339 cm3/g) and smaller band gap than 6%RGO/TiO2. More importantly, 25%RGO/TiO2 demonstrated higher adsorption efficiency (25%) and 4 times faster degradation rate than TiO2 (0%). It also exhibited good capability to eliminate multiple organics and stable long-term cycle performance (up to 93% retention after 30 cycles). Its superiority was attributed to the large surface area and unique interface between TiO2 and RGO, which not only provided more active sites to capture pollutants but also enhanced charge transfer (3 µA/cm2, 5 times higher than TiO2). This work offered a promising way to purify water through engineering new materials structure and integrating adsorption and photodegradation technologies. © 2018 IOP Publishing Ltd.

Correlation of the plasmon-enhanced photoconductance and photovoltaic properties of core-shell Au@TiO{sub 2} network

Energy Technology Data Exchange (ETDEWEB)

Yang, Yiqun [Department of Chemistry, Kansas State University, Manhattan, Kansas 66506 (United States); Wu, Judy [Department of Physics and Astronomy, University of Kansas, Lawrence, Kansas 66045 (United States); Li, Jun, E-mail: junli@ksu.edu [Department of Chemistry, Kansas State University, Manhattan, Kansas 66506 (United States); College of Chemistry and Chemical Engineering, Hubei Normal University, Huangshi, Hubei 435002 (China)

2016-08-29

This study reveals the contribution of hot electrons from the excited plasmonic nanoparticles in dye sensitized solar cells (DSSCs) by correlating the photoconductance of a core-shell Au@TiO{sub 2} network on a micro-gap electrode and the photovolatic properties of this material as photoanodes in DSSCs. The distinct wavelength dependence of these two devices reveals that the plasmon-excited hot electrons can easily overcome the Schottky barrier at Au/TiO{sub 2} interface in the whole visible wavelength range and transfer from Au nanoparticles into the TiO{sub 2} network. The enhanced charge carrier density leads to higher photoconductance and facilitates more efficient charge separation and photoelectron collection in the DSSCs.

Enhanced photovoltaic performance of a quantum dot-sensitized solar cell using a Nb-doped TiO2 electrode

International Nuclear Information System (INIS)

Jiang, Lei; You, Ting; Deng, Wei-Qiao

2013-01-01

In this work Nb-doped anatase TiO 2 nanocrystals are used as the photoanode of quantum-dot-sensitized solar cells. A solar cell with CdS/CdSe quantum dots co-sensitized 2.5 mol% Nb-doped anatase TiO 2 nanocrystals can achieve a photovoltaic conversion efficiency of 3.3%, which is almost twice as high as the 1.7% obtained by a cell based on undoped TiO 2 nanocrystals. The incident photon-to-current conversion efficiency can reach as high as 91%, which is a record for all quantum-dot-sensitized solar cells. Detailed analysis shows that such an enhancement is due to improved lifetime and diffusion length of electrons in the solar cell. (paper)

Enhanced photovoltaic performance of a quantum dot-sensitized solar cell using a Nb-doped TiO2 electrode.

Science.gov (United States)

Jiang, Lei; You, Ting; Deng, Wei-Qiao

2013-10-18

In this work Nb-doped anatase TiO2 nanocrystals are used as the photoanode of quantum-dot-sensitized solar cells. A solar cell with CdS/CdSe quantum dots co-sensitized 2.5 mol% Nb-doped anatase TiO2 nanocrystals can achieve a photovoltaic conversion efficiency of 3.3%, which is almost twice as high as the 1.7% obtained by a cell based on undoped TiO2 nanocrystals. The incident photon-to-current conversion efficiency can reach as high as 91%, which is a record for all quantum-dot-sensitized solar cells. Detailed analysis shows that such an enhancement is due to improved lifetime and diffusion length of electrons in the solar cell.

Enhanced Energy-Storage Density and High Efficiency of Lead-Free CaTiO3-BiScO3 Linear Dielectric Ceramics.

Science.gov (United States)

Luo, Bingcheng; Wang, Xiaohui; Tian, Enke; Song, Hongzhou; Wang, Hongxian; Li, Longtu

2017-06-14

A novel lead-free (1 - x)CaTiO 3 -xBiScO 3 linear dielectric ceramic with enhanced energy-storage density was fabricated. With the composition of BiScO 3 increasing, the dielectric constant of (1 - x)CaTiO 3 -xBiScO 3 ceramics first increased and then decreased after the composition x > 0.1, while the dielectric loss decreased first and increased. For the composition x = 0.1, the polarization was increased into 12.36 μC/cm 2 , 4.6 times higher than that of the pure CaTiO 3 . The energy density of 0.9CaTiO 3 -0.1BiScO 3 ceramic was 1.55 J/cm 3 with the energy-storage efficiency of 90.4% at the breakdown strength of 270 kV/cm, and the power density was 1.79 MW/cm 3 . Comparison with other lead-free dielectric ceramics confirmed the superior potential of CaTiO 3 -BiScO 3 ceramics for the design of ceramics capacitors for energy-storage applications. First-principles calculations revealed that Sc subsitution of Ti-site induced the atomic displacement of Ti ions in the whole crystal lattice, and lattice expansion was caused by variation of the bond angles and lenghths. Strong hybridization between O 2p and Ti 3d was observed in both valence band and conduction band; the hybridization between O 2p and Sc 3d at high conduction band was found to enlarge the band gap, and the static dielectric tensors were increased, which was the essential for the enhancement of polarization and dielectric properties.

Facile synthesis of Ag nanoparticles supported on TiO2 inverse opal with enhanced visible-light photocatalytic activity

International Nuclear Information System (INIS)

Zhao Yongxun; Yang Beifang; Xu Jiao; Fu Zhengping; Wu Min; Li Feng

2012-01-01

TiO 2 inverse opal films loaded with silver nanoparticles (ATIO) were synthesized on glass substrates. TiO 2 inverse opal (TIO) films were prepared via a sol–gel process using self-assembly of SiO 2 colloidal crystal template and a facile wet chemical route featuring an AgNO 3 precursor solution to fabricate silver nanoparticles on the TIO films. The inverse opal structure and Ag deposition physically and chemically modify titania, respectively. The catalysts were characterized by Raman spectroscopy, field-emission scanning electron microscopy, high-resolution transmission electron microscopy (HRTEM), UV–vis absorption spectra, X-ray photoelectron spectroscopy and photoluminescence spectroscopy. The HRTEM results show that Ag nanoparticles measuring 5–10 nm were evenly distributed on TIO. Both the UV- and visible-light photocatalytic activities of the samples were evaluated by analyzing the degradation of methylene blue (MB) in aqueous solution. The results reveal that the apparent reaction rate constant (k app ) of MB degradation of the sample ATIO under UV-light irradiation is approximately 1.5 times that of the conventional Ag-loaded TiO 2 film (ATF) without an ordered porous structure at an AgNO 3 concentration of 5 mM in the precursor solution. At an AgNO 3 concentration of 10 mM, the sample exhibits a k app value approximately 4.2 times that of ATF under visible-light irradiation. This enhanced visible-light photocatalytic performance can be attributed to the synergistic effect of optimized Ag nanoparticle deposition and an ordered macroporous TIO structure. Repeated cycling tests revealed that the samples showed stable photocatalytic activity, even after six repeated cycles. - Highlights: ►TiO 2 inverse opal films loaded with silver nanoparticles were synthesized. ►Physical and chemical modifications of TiO 2 were achieved simultaneously. ►The catalysts exhibited enhanced visible-light photocatalytic activity. ►The mechanism for enhanced

NiTiCu/AlN/NiTiCu shape memory thin film heterostructures for vibration damping in MEMS

Energy Technology Data Exchange (ETDEWEB)

Kaur, Navjot; Kaur, Davinder, E-mail: dkaurfph@iitr.ernet.in

2014-03-25

Highlights: • Fabrication of NiTiCu/AlN/NiTiCu heterostructure using dc/rf magnetron sputtering. • Exhibits highest hardness (38 GPa) and elastic modulus (187 GPa). • Enhanced dissipation of mechanical energy (E{sub d} = 5.7 N J). • High damping capacity (0.052) and figure of merit (∼0.62). • Can be applied for vibration damping in MEMS. -- Abstract: Shape memory alloy (NiTiCu) thin films coupled with piezoelectric AlN layer produce an intelligent material for vibration damping. In the present study pure NiTiCu, NiTiCu/AlN and NiTiCu/AlN/NiTiCu heterostructures have been deposited on Si substrate using magnetron sputtering technique. By the use of the interfaces and shape memory effect provided by NiTiCu layers, the damping capacity can be increased along with increase in stiffness and mechanical hardness. The heterostructures were characterized in terms of structural, electrical, morphological and mechanical properties by X-ray diffraction (XRD), four probe resistivity method, atomic force microscopy, field emission scanning electron microscopy, and nanoindentation. The NiTiCu/AlN/NiTiCu heterostructure exhibit enhanced mechanical and damping properties as compared to NiTiCu/AlN and pure NiTiCu. This enhancement in hardness and damping of the heterostructure could be attributed to the shape memory effect of NiTiCu, intrinsic piezoelectricity of AlN and increased number of interfaces in heterostructure that help in dissipation of mechanical vibrations. The findings of this work provide additional impetus for the application of these heterostructures in emerging fields of nanotechnology and microelectro mechanical (MEMS) devices.

NiTiCu/AlN/NiTiCu shape memory thin film heterostructures for vibration damping in MEMS

International Nuclear Information System (INIS)

Kaur, Navjot; Kaur, Davinder

2014-01-01

Highlights: • Fabrication of NiTiCu/AlN/NiTiCu heterostructure using dc/rf magnetron sputtering. • Exhibits highest hardness (38 GPa) and elastic modulus (187 GPa). • Enhanced dissipation of mechanical energy (E d = 5.7 N J). • High damping capacity (0.052) and figure of merit (∼0.62). • Can be applied for vibration damping in MEMS. -- Abstract: Shape memory alloy (NiTiCu) thin films coupled with piezoelectric AlN layer produce an intelligent material for vibration damping. In the present study pure NiTiCu, NiTiCu/AlN and NiTiCu/AlN/NiTiCu heterostructures have been deposited on Si substrate using magnetron sputtering technique. By the use of the interfaces and shape memory effect provided by NiTiCu layers, the damping capacity can be increased along with increase in stiffness and mechanical hardness. The heterostructures were characterized in terms of structural, electrical, morphological and mechanical properties by X-ray diffraction (XRD), four probe resistivity method, atomic force microscopy, field emission scanning electron microscopy, and nanoindentation. The NiTiCu/AlN/NiTiCu heterostructure exhibit enhanced mechanical and damping properties as compared to NiTiCu/AlN and pure NiTiCu. This enhancement in hardness and damping of the heterostructure could be attributed to the shape memory effect of NiTiCu, intrinsic piezoelectricity of AlN and increased number of interfaces in heterostructure that help in dissipation of mechanical vibrations. The findings of this work provide additional impetus for the application of these heterostructures in emerging fields of nanotechnology and microelectro mechanical (MEMS) devices

Enhanced Performance of MoS2 Photodetectors by Inserting an ALD-Processed TiO2 Interlayer

KAUST Repository

Pak, Yusin

2017-12-05

2D molybdenum disulfide (MoS2) possesses excellent optoelectronic properties that make it a promising candidate for use in high-performance photodetectors. Yet, to meet the growing demand for practical and reliable MoS2 photodetectors, the critical issue of defect introduction to the interface between the exfoliated MoS2 and the electrode metal during fabrication must be addressed, because defects deteriorate the device performance. To achieve this objective, the use of an atomic layer-deposited TiO2 interlayer (between exfoliated MoS2 and electrode) is reported in this work, for the first time, to enhance the performance of MoS2 photodetectors. The TiO2 interlayer is inserted through 20 atomic layer deposition cycles before depositing the electrode metal on MoS2/SiO2 substrate, leading to significantly enhanced photoresponsivity and response speed. These results pave the way for practical applications and provide a novel direction for optimizing the interlayer material.

Enhanced Performance of MoS2 Photodetectors by Inserting an ALD-Processed TiO2 Interlayer

KAUST Repository

Pak, Yusin; Park, Woojin; Mitra, Somak; Devi, Assa Aravindh Sasikala; Loganathan, Kalaivanan; Kumaresan, Yogeenth; Kim, Yonghun; Cho, Byungjin; Jung, Gun-Young; Hussain, Muhammad Mustafa; Roqan, Iman S.

2017-01-01

2D molybdenum disulfide (MoS2) possesses excellent optoelectronic properties that make it a promising candidate for use in high-performance photodetectors. Yet, to meet the growing demand for practical and reliable MoS2 photodetectors, the critical issue of defect introduction to the interface between the exfoliated MoS2 and the electrode metal during fabrication must be addressed, because defects deteriorate the device performance. To achieve this objective, the use of an atomic layer-deposited TiO2 interlayer (between exfoliated MoS2 and electrode) is reported in this work, for the first time, to enhance the performance of MoS2 photodetectors. The TiO2 interlayer is inserted through 20 atomic layer deposition cycles before depositing the electrode metal on MoS2/SiO2 substrate, leading to significantly enhanced photoresponsivity and response speed. These results pave the way for practical applications and provide a novel direction for optimizing the interlayer material.

Current-induced nonuniform enhancement of sheet resistance in A r+ -irradiated SrTi O3

Science.gov (United States)

Roy, Debangsu; Frenkel, Yiftach; Davidovitch, Sagi; Persky, Eylon; Haham, Noam; Gabay, Marc; Kalisky, Beena; Klein, Lior

2017-06-01

The sheet resistance Rs of A r+ irradiated SrTi O3 in patterns with a length scale of several microns increases significantly below ˜40 K in connection with driving currents exceeding a certain threshold. The initial lower Rs is recovered upon warming with accelerated recovery around 70 and 160 K. Scanning superconducting quantum interference device microscopy shows local irreversible changes in the spatial distribution of the current with a length scale of several microns. We attribute the observed nonuniform enhancement of Rs to the attraction of the charged single-oxygen and dioxygen vacancies by the crystallographic domain boundaries in SrTi O3 . The boundaries, which are nearly ferroelectric below 40 K, are polarized by the local electrical field associated with the driven current and the clustered vacancies which suppress conductivity in their vicinity and yield a noticeable enhancement in the device resistance when the current path width is on the order of the boundary extension. The temperatures of accelerated conductivity recovery are associated with the energy barriers for the diffusion of the two types of vacancies.

Low temperature synthesis of polyaniline-crystalline TiO2-halloysite composite nanotubes with enhanced visible light photocatalytic activity.

Science.gov (United States)

Li, Cuiping; Wang, Jie; Guo, Hong; Ding, Shujiang

2015-11-15

A series of one-dimensional polyaniline-crystalline TiO2-halloysite composite nanotubes with different mass ratio of polyaniline to TiO2 are facilely prepared by employing the low-temperature synthesis of crystalline TiO2 on halloysite nanotubes. The halloysite nanotubes can adsorb TiO2/polyaniline precursors and induce TiO2 nanocrystals/polyaniline to grow on the support in situ simultaneously. By simply adjusting the acidity of reaction system, PANI-crystalline TiO2-HA composite nanotubes composed of anatase, a mixed phase TiO2 and different PANI redox state are obtained. The XRD and UV-vis results show that the surface polyaniline sensitization has no effect on the crystalline structure of halloysite and TiO2 and the light response of TiO2 is extended to visible-light regions. Photocatalysis test results reveal the photocatalytic activity will be affected by the pH value and the volume ratio of ANI to TTIP. The highest photocatalytic activity is achieved with the composite photocatalysts prepared at pH 0.5 and 1% volume ratio of ANI and TTIP owing to the sensitizing effect of polyaniline and the charge transfer from the photoexcited PANI sensitizer to TiO2. Moreover, the PANI-TiO2-HA composite nanotubes synthesized by one-step at pH 0.5 with 1% volume ratio of ANI to TTIP exhibit higher visible light photocatalytic activity than those synthesized by the two-step. Heterogeneous PANI-TiO2-HA composite nanotubes prepared at pH 0.5 exhibit a higher degradation activity than that prepared at pH 1.5. The redoped experiment proves that the PANI redox state plays the main contribution to the enhanced visible light catalytic degradation efficiency of PANI-TiO2-HA prepared at pH 0.5. Furthermore, the heterogeneous PANI-crystalline TiO2-HA nanotubes have good photocatalytic stability and can be reused four times with only gradual loss of activity under visible light irradiation. Copyright © 2015 Elsevier Inc. All rights reserved.

Fabrication of TiO_2 nanorod assembly grafted rGO (rGO@TiO_2-NR) hybridized flake-like photocatalyst

International Nuclear Information System (INIS)

Lv, Kangle; Fang, Shun; Si, Lingling; Xia, Yang; Ho, Wingkei; Li, Mei

2017-01-01

Highlights: • TiO_2 nanorod assembly grafted with GO hybrid was successfully fabricated. • TiO_2 nanorods can reduce the aggregation of TiO_2 nanoparticles on graphene. • This unique structure facilitates the injection of electron from TiO_2 to graphene. - Abstract: To efficiently separate the photo-generated electron–hole pairs of TiO_2 hybrid, anatase TiO_2 nanorod assembly grafted reduced graphene oxides (rGO@TiO_2-NR) hybrid was successfully fabricated using potassium titanium oxalate (PTO) and graphene oxides (GO) as starting materials and diethylene glycol (DEG) as reductant. The effect of GO content on the structure and photocatalytic activity of rGO@TiO_2-NR composite was systematically studied. Results show that, in the absence of GO, only TiO_2 microsphere assembly is obtained from TiO_2 nanorods. The presence of GO results in the formation of a flake-like TiO_2-nanorod-assembled grafted rGO hybrid. The photocatalytic activity of rGO@TiO_2-NR composite increases first and then decreases with increase in the amount of GO from 0 wt.% to 10 wt.%. The hybridized S4 sample prepared with 4 wt.% GO possesses the highest photocatalytic activity with a constant rate of 0.039 min"−"1 in the photocataytic degradation of Brilliant X-3B dye (X3B); this sample was enhanced more than three times when compared with pure TiO_2 sample (0.012 min"−"1). The enhanced photocatalytic activity of the rGO@TiO_2-NR hybrid was attributed to the strong interaction between TiO_2 nanorods and rGO. The unique hierarchical structure of 1D nanorod assembly TiO_2–rGO flakes facilitates the injection and transfer of photo-generated electrons from TiO_2 to graphene, thus retarding the recombination of electron–hole pairs and enhancing the photocatalytic activity. The enlarged BET surface areas, not only increasing the number of active sites, but also facilitating the adsorption of the dye, and improved light-harvesting ability also contribute to the enhanced photoreactivity

Enhanced photoelectrocatalytic degradation of 2,4-dichlorophenoxyacetic acid by CuInS2 nanoparticles deposition onto TiO2 nanotube arrays

International Nuclear Information System (INIS)

Liu Ronghua; Liu Yutang; Liu Chengbin; Luo Shenglian; Teng Yarong; Yang Lixia; Yang Renbin; Cai Qingyun

2011-01-01

Research highlights: → The photocatalytic application of CuInS 2 with a direct band gap of about 1.5 eV and a high absorption coefficient remains unknown. → We describe an impulse electrodeposition approach to deposit CuInS 2 nanoparticles in uniform size of about 20 nm onto the top surface of the highly oriented TiO 2 NT arrays while minimizing the clogging of the tube entrances. → The novel photocatalyst exhibits a highly visible-light photocatalytic degradation activity for the target organic pollutant. → Moreover, the stability of the modified TiO 2 NT is good. → Therefore, CuInS 2 nanoparticles modified TiO 2 NT photocatalysts have potential utility in practical purification of organic wastewater. - Abstract: Surface modification of TiO 2 nanotube (NT) arrays with CuInS 2 nanoparticles (NPs) for photocatalytic degradation of 2,4-dichlorophenoxyacetic acid (2,4-D) was reported. A pulse electrodeposition technique was used to prepare the CuInS 2 NPs, and the resulted CuInS 2 NPs, with a uniform size of about 20 nm, were found to deposit on the top surface of the highly oriented TiO 2 NT while without clogging the tube entrances. Compared with the unmodified TiO 2 NT, the CuInS 2 NPs modified TiO 2 NT (CuInS 2 -TiO 2 NT) showed significantly enhanced photocatalytic activity towards 2,4-D under visible light. After 160 min irradiation, the removal rate of 2,4-D is 100% by using CuInS 2 -TiO 2 NT, much higher than 65.2% by using the unmodified TiO 2 NT in photoelectrocatalytic process. The increased photodegradation efficiency mainly results from the improved photocurrent density as results of enhanced visible-light absorption and decreased hole-electron recombination due to the presence of narrow-band-gap p-type semiconductor CuInS 2 .

Enhanced field emission properties of tilted graphene nanoribbons on aggregated TiO{sub 2} nanotube arrays

Energy Technology Data Exchange (ETDEWEB)

Hung, Shang-Chao, E-mail: schung99@gmail.com [Department of Information Technology & Communication, Shih Chien University Kaohsiung Campus, Neimen, Kaohsiung 845, Taiwan (China); Chen, Yu-Jyun [Graduate Institute of Electro-Optical Engineering & Department of Electronic Engineering, National Taiwan University of Science and Technology, Taipei 106, Taiwan (China)

2016-07-15

Highlights: • Graphene nanoribbons (GNBs) slanted on aggregate TiO{sub 2} nanotube (A-TNTs) as field-emitters. • Turn-on electric field and field enhancement factor β are dependent on the substrate morphology. • Various quantities of GNRs are deposited on top of A-TNTs (GNRs/A-TNTs) with different morphologies. • With an increase of GNBs compositions, the specimens' turn-on electric field is reduced to 2.8 V/μm. • The field enhancement factor increased rapidly to about 1964 with the addition of GNRs. - Abstract: Graphene nanoribbons (GNRs) slanted on aggregate TiO{sub 2} nanotube arrays (A-TNTs) with various compositions as field-emitters are reported. The morphology, crystalline structure, and composition of the as-obtained specimens were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD) and Raman spectrometry. The dependence of the turn-on electric field and the field enhancement factor β on substrate morphology was studied. An increase of GNRs reduces the specimens’ turn-on electric field to 2.8 V/μm and the field enhancement factor increased rapidly to about 1964 with the addition of GNRs. Results show a strong dependence of the field emission on GNR composition aligned with the gradient on the top of the A-TNT substrate. Enhanced FE properties of the modified TNTs can be mainly attributed to their improved electrical properties and rougher surface morphology.

Comparison study on photocatalytic oxidation of pharmaceuticals by TiO{sub 2}-Fe and TiO{sub 2}-reduced graphene oxide nanocomposites immobilized on optical fibers

Energy Technology Data Exchange (ETDEWEB)

Lin, Lu; Wang, Huiyao, E-mail: huiyao@nmsu.edu; Jiang, Wenbin; Mkaouar, Ahmed Radhi; Xu, Pei, E-mail: pxu@nmsu.edu

2017-07-05

Highlights: • Incorporating rGO or Fe{sup 3+} ions in TiO{sub 2} photocatalyst could enhance photocatalysis. • TiO{sub 2}-rGO exhibited higher photocatalytic activity under UV irradiation. • TiO{sub 2}-Fe demonstrated more suitable for visible light irradiation. • Reduced recombination rate contributed to enhanced photocatalysis of TiO{sub 2}-rGO. • Narrower band gap accounted for increased photocatalytic activity of TiO{sub 2}-Fe. - Abstract: Incorporating reduced graphene oxide (rGO) or Fe{sup 3+} ions in TiO{sub 2} photocatalyst could enhance photocatalytic degradation of organic contaminants in aqueous solutions. This study characterized the photocatalytic activities of TiO{sub 2}-Fe and TiO{sub 2}-rGO nanocomposites immobilized on optical fibers synthesized by polymer assisted hydrothermal deposition method. The photocatalysts presented a mixture phase of anatase and rutile in the TiO{sub 2}-rGO and TiO{sub 2}-Fe nanocomposites. Doping Fe into TiO{sub 2} particles (2.40 eV) could reduce more band gap energy than incorporating rGO (2.85 eV), thereby enhancing utilization efficiency of visible light. Incorporating Fe and rGO in TiO{sub 2} decreased significantly the intensity of TiO{sub 2} photoluminescence signals and enhanced the separation rate of photo-induced charge carriers. Photocatalytic performance of the synthesized nanocomposites was measured by the degradation of three pharmaceuticals under UV and visible light irradiation, including carbamazepine, ibuprofen, and sulfamethoxazole. TiO{sub 2}-rGO exhibited higher photocatalytic activity for the degradation of pharmaceuticals under UV irradiation, while TiO{sub 2}-Fe demonstrated more suitable for visible light oxidation. The results suggested that the enhanced photocatalytic performance of TiO{sub 2}-rGO could be attributed to reduced recombination rate of photoexcited electrons-hole pairs, but for TiO{sub 2}-Fe nanocomposite, narrower band gap would contribute to increased photocatalytic

Enhanced light harvesting of TiO{sub 2}/La{sub 0.95}Tb{sub 0.05}PO{sub 4} photoanodes for dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Zhang, Hongna; He, Benlin, E-mail: blhe@ouc.edu.cn; Tang, Qunwei, E-mail: tangqunwei@ouc.edu.cn

2016-04-15

With an aim of enhancing light harvesting for dye adsorption and therefore photovoltaic performances of dye-sensitized solar cells (DSSCs), we present here an employment of La{sub 0.95}Tb{sub 0.05}PO{sub 4} incorporated TiO{sub 2} nanocrystallites as photoanodes. The preliminary results demonstrate that the dye absorption and therefore electron generation have been markedly enhanced, arising from the conversion of ultraviolet to visible light by La{sub 0.95}Tb{sub 0.05}PO{sub 4}. The crystal structure and light harvesting performances of photoanodes are optimized by adjusting La{sub 0.95}Tb{sub 0.05}PO{sub 4} dosage. The power conversion efficiency is enhanced from 6.52% for pristine TiO{sub 2} based DSSC to 7.27% for the device employing TiO{sub 2}/0.5 wt% La{sub 0.95}Tb{sub 0.05}PO{sub 4}, yielding an efficiency enhancement by 11.35%. This study provides a new strategy for the fabrication of highly efficient DSSCs. - Highlights: • TiO{sub 2}/La{sub 0.95}Tb{sub 0.05}PO{sub 4} nanocrystallites are fabricated by a facile hydrothermal method. • The light intensity and therefore dye excitation have been markedly enhanced. • A conversion efficiency of 7.27% for the DSSC employing TiO{sub 2}/0.5 wt% La{sub 0.95}Tb{sub 0.05}PO{sub 4} is obtained. • The strategy provides new opportunities for efficient DSSCs.

Enhanced photovoltaic properties in graphitic carbon nanospheres networked TiO{sub 2} nanocomposite based dye sensitized solar cell

Energy Technology Data Exchange (ETDEWEB)

Agarwal, Radhe [Department of Physics and Institute for Functional Nanomaterials, University of Puerto Rico, San Juan, PR 00931 (United States); Sahoo, Satyaprakash, E-mail: satya504@gmail.com [Department of Physics and Institute for Functional Nanomaterials, University of Puerto Rico, San Juan, PR 00931 (United States); Chitturi, Venkateswara Rao [Department of Physics and Institute for Functional Nanomaterials, University of Puerto Rico, San Juan, PR 00931 (United States); Williams, Joseph D. [Department of Biomedical and Chemical Engineering, Syracuse University, L.C. Smith College of Engineering and Computer Science, Syracuse, NY (United States); Resto, Oscar [Department of Physics and Institute for Functional Nanomaterials, University of Puerto Rico, San Juan, PR 00931 (United States); Katiyar, Ram S., E-mail: rkatiyar@hpcf.uprrp.edu [Department of Physics and Institute for Functional Nanomaterials, University of Puerto Rico, San Juan, PR 00931 (United States)

2015-08-25

Highlights: • Nano size graphitic carbon nanospheres were prepared from MWCNTs. • TiO{sub 2}/GCNS composite was used as the photoanode in dye-sensitized solar cell. • An improved photovoltaic performance with GCNS–TiO{sub 2} composite was noticed. - Abstract: In this work, we report a novel carbon based TiO{sub 2} nanocomposite electron injection layer (photoanode) toward the improved performance of DSSCs. Graphitic carbon nanospheres (GCNSs) were synthesized by a unique acidic treatment of multi-wall carbon nanotubes. GCNS–TiO{sub 2} nanocomposites with different concentrations of GCNSs (ranging from 5 to 20 μL) were prepared to use as photoanodes in DSSCs. Structural and morphological properties of GCNS–TiO{sub 2} nanocomposites were analyzed by Raman spectroscopy and ultra-high resolution transmission electron microscopy techniques, respectively. A systematic increment in the short circuit current density (J{sub SC}) and open circuit voltage (V{sub OC}) of DSSC was observed by increasing GCNS concentration up to an optimal value, possibly due to the combined effect of slight rise in quasi-Fermi level and higher carrier transport rate in the resultant composite. Thus, a significant enhancement of ∼47% in the efficiency of DSSC containing GCNS–TiO{sub 2} photoanode was observed as compare to DSSC with pure TiO{sub 2} photoanode.

Fabrication of TiO2 nanorod assembly grafted rGO (rGO@TiO2-NR) hybridized flake-like photocatalyst

Science.gov (United States)

Lv, Kangle; Fang, Shun; Si, Lingling; Xia, Yang; Ho, Wingkei; Li, Mei

2017-01-01

To efficiently separate the photo-generated electron-hole pairs of TiO2 hybrid, anatase TiO2 nanorod assembly grafted reduced graphene oxides (rGO@TiO2-NR) hybrid was successfully fabricated using potassium titanium oxalate (PTO) and graphene oxides (GO) as starting materials and diethylene glycol (DEG) as reductant. The effect of GO content on the structure and photocatalytic activity of rGO@TiO2-NR composite was systematically studied. Results show that, in the absence of GO, only TiO2 microsphere assembly is obtained from TiO2 nanorods. The presence of GO results in the formation of a flake-like TiO2-nanorod-assembled grafted rGO hybrid. The photocatalytic activity of rGO@TiO2-NR composite increases first and then decreases with increase in the amount of GO from 0 wt.% to 10 wt.%. The hybridized S4 sample prepared with 4 wt.% GO possesses the highest photocatalytic activity with a constant rate of 0.039 min-1 in the photocataytic degradation of Brilliant X-3B dye (X3B); this sample was enhanced more than three times when compared with pure TiO2 sample (0.012 min-1). The enhanced photocatalytic activity of the rGO@TiO2-NR hybrid was attributed to the strong interaction between TiO2 nanorods and rGO. The unique hierarchical structure of 1D nanorod assembly TiO2-rGO flakes facilitates the injection and transfer of photo-generated electrons from TiO2 to graphene, thus retarding the recombination of electron-hole pairs and enhancing the photocatalytic activity. The enlarged BET surface areas, not only increasing the number of active sites, but also facilitating the adsorption of the dye, and improved light-harvesting ability also contribute to the enhanced photoreactivity of rGO@TiO2-NR hybrid.

The role of TiB2 in strengthening TiB2 reinforced aluminium casting composites

International Nuclear Information System (INIS)

Chen, Z; Kang, H; Zhao, Y; Zheng, Y; Wang, T

2016-01-01

With an aim of developing high quality in situ TiB 2 reinforced aluminium foundry alloy based composites, the conventional direct synthesis method was modified into a two-step route. In step one we optimized the halide salt route to fabricate in situ TiB 2 particulate reinforced aluminium matrix composites and in step two we investigated the effects of the Al-5wt.% TiB 2 composite, as a “master composite”, on strengthening the practical foundry alloys. The in situ formed TiB 2 particles play two roles while strengthening the composites: (1) The grain refinement effect that improves the quality of the alloy matrix; and (2) The interactions between the hard particulates and the matrix add extra increment to the material strength. In different alloy systems, TiB 2 may play distinct roles in these two aspects (figure 1). Further analysis of the strengthening mechanisms shows that particle agglomeration behaviour during solidification is responsible for the latter one. The present work details the role of TiB 2 in strengthening TiB 2 reinforced aluminium casting composites. (paper)

Promoted Fixation of Molecular Nitrogen with Surface Oxygen Vacancies on Plasmon-Enhanced TiO2 Photoelectrodes.

Science.gov (United States)

Li, Chengcheng; Wang, Tuo; Zhao, Zhi-Jian; Yang, Weimin; Li, Jian-Feng; Li, Ang; Yang, Zhilin; Ozin, Geoffrey A; Gong, Jinlong

2018-02-19

A hundred years on, the energy-intensive Haber-Bosch process continues to turn the N 2 in air into fertilizer, nourishing billions of people while causing pollution and greenhouse gas emissions. The urgency of mitigating climate change motivates society to progress toward a more sustainable method for fixing N 2 that is based on clean energy. Surface oxygen vacancies (surface O vac ) hold great potential for N 2 adsorption and activation, but introducing O vac on the very surface without affecting bulk properties remains a great challenge. Fine tuning of the surface O vac by atomic layer deposition is described, forming a thin amorphous TiO 2 layer on plasmon-enhanced rutile TiO 2 /Au nanorods. Surface O vac in the outer amorphous TiO 2 thin layer promote the adsorption and activation of N 2 , which facilitates N 2 reduction to ammonia by excited electrons from ultraviolet-light-driven TiO 2 and visible-light-driven Au surface plasmons. The findings offer a new approach to N 2 photofixation under ambient conditions (that is, room temperature and atmospheric pressure). © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Surface modification and enhanced photocatalytic CO{sub 2} reduction performance of TiO{sub 2}: a review

Energy Technology Data Exchange (ETDEWEB)

Low, Jingxiang; Cheng, Bei [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Luoshi Road 122, Wuhan 430070 (China); Yu, Jiaguo, E-mail: jiaguoyu@yahoo.com [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Luoshi Road 122, Wuhan 430070 (China); Department of Physics, Faculty of Science, King Abdulaziz University, Jeddah 21589 (Saudi Arabia)

2017-01-15

Highlights: • Application of modified TiO{sub 2} for photocatalytic CO{sub 2} reduction is summarized. • Different surface modification strategies of TiO{sub 2} are highlighted. • Summary and future perspectives in photocatalytic CO{sub 2} reduction are presented. - Abstract: Recently, the excessive consumption of fossil fuels has caused high emissions of the greenhouse gases, CO{sub 2} into atmosphere and global energy crisis. Mimicking the natural photosynthesis by using semiconductor materials to achieve photocatalytic CO{sub 2} reduction into valuable solar fuels such as CH{sub 4}, HCO{sub 2}H, CH{sub 2}O, and CH{sub 3}OH is known as one of the best solutions for addressing the aforementioned issue. Among various proposed photocatalysts, TiO{sub 2} has been extensively studied over the past several decades for photocatalytic CO{sub 2} reduction because of its cheapness and environmental friendliness. Particularly, surface modification of TiO{sub 2} has attracted numerous interests due to its capability of enhancing the light absorption ability, facilitating the electron-hole separation, tuning the CO{sub 2} reduction selectivity and increasing the CO{sub 2} adsorption and activation ability of TiO{sub 2} for photocatalytic CO{sub 2} reduction. In this review, recent approaches of the surface modification of TiO{sub 2} for photocatalytic CO{sub 2} reduction, including impurity doping, metal deposition, alkali modification, heterojunction construction and carbon-based material loading, are presented. The photocatalytic CO{sub 2} reduction mechanism and pathways of TiO{sub 2} are discussed. The future research direction and perspective of photocatalytic CO{sub 2} reduction over surface-modified TiO{sub 2} are also presented.

Plasma enhanced atomic layer batch processing of aluminum doped titanium dioxide

International Nuclear Information System (INIS)

Lehnert, Wolfgang; Ruhl, Guenther; Gschwandtner, Alexander

2012-01-01

Among many promising high-k dielectrics, TiO 2 is an interesting candidate because of its relatively high k value of over 40 and its easy integration into existing semiconductor manufacturing schemes. The most critical issues of TiO 2 are its low electrical stability and its high leakage current density. However, doping TiO 2 with Al has shown to yield significant improvement of layer quality on Ru electrodes [S. K. Kim et al., Adv. Mater. 20, 1429 (2008)]. In this work we investigated if atomic layer deposition (ALD) of Al doped TiO 2 is feasible in a batch system. Electrical characterizations were done using common electrode materials like TiN, TaN, or W. Additionally, the effect of plasma enhanced processing in this reactor was studied. For this investigation a production batch ALD furnace has been retrofitted with a plasma source which can be used for post deposition anneals with oxygen radicals as well as for directly plasma enhanced ALD. After evaluation of several Ti precursors a deposition process for AlTiO x with excellent film thickness and composition uniformity was developed. The effects of post deposition anneals, Al 2 O 3 interlayers between electrode and TiO 2 , Al doping concentration, plasma enhanced deposition and electrode material type on leakage current density are shown. An optimized AlTiO x deposition process on TaN electrodes yields to leakage current density of 5 x 10 -7 A/cm 2 at 2 V and k values of about 35. Thus, it could be demonstrated that a plasma enhanced batch ALD process for Al doped TiO 2 is feasible with acceptable leakage current density on a standard electrode material.

Centrically reordered inversion recovery half-Fourier single-shot turbo spin-echo sequence: improvement of the image quality of oxygen-enhanced MRI

International Nuclear Information System (INIS)

Ohno, Yoshiharu; Hatabu, Hiroto; Higashino, Takanori; Kawamitsu, Hideaki; Watanabe, Hirokazu; Takenaka, Daisuke; Cauteren, Marc van; Sugimura, Kazuro

2004-01-01

Purpose: The purpose of the study presented here was to determine the improvement in image quality of oxygen-enhanced magnetic resonance (MR) subtraction imaging obtained with a centrically reordered inversion recovery half-Fourier single-shot turbo spin-echo (c-IR-HASTE) sequence compared with that obtained with a conventional sequentially reordered inversion recovery single-shot HASTE (s-IR-HASTE) sequence for pulmonary imaging. Materials and methods: Oxygen-enhanced MR imaging using a 1.5 T whole body scanner was performed on 12 healthy, non-smoking volunteers. Oxygen-enhanced MR images were obtained with the coronal two-dimensional (2D) c-IR-HASTE sequence and 2D s-IR-HASTE sequence combined with respiratory triggering. For a 256x256 matrix, 132 phase-encoding steps were acquired including four steps for phase correction. Inter-echo spacing for each sequence was 4.0 ms. The effective echo time (TE) for c-IR-HASTE was 4.0 ms, and 16 ms for s-IR-HASTE. The inversion time (TI) was 900 ms. To determine the improvement in oxygen-enhanced MR subtraction imaging by c-IR-HASTE, CNRs of subtraction image, overall image quality, and image degradation of the c-IR-HASTE and s-IR-HASTE techniques were statistically compared. Results: CNR, overall image quality, and image degradation of c-IR-HASTE images showed significant improvement compared to those s-IR-HASTE images (P<0.05). Conclusion: Centrically reordered inversion recovery half-Fourier single-shot turbo spin-echo (c-IR-HASTE) sequence enhanced the signal from the lung and improved the image quality of oxygen-enhanced MR subtraction imaging

CdS/TiO{sub 2} nanocomposite film and its enhanced photoelectric responses to dry air and formaldehyde induced by visible light at room temperature

Energy Technology Data Exchange (ETDEWEB)

Zou, Zhijun, E-mail: zjzou@xynu.edu.cn [Key Laboratory of Advanced Micro/Nano Functional Materials, Department of Physics and Electronic Engineering, Xinyang Normal University, Xinyang 464000 (China); State Key Laboratory of Material Processing and Die & Mould Technology, Nanomaterials and Smart Sensors Research Laboratory, Department of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Qiu, Yang [Key Laboratory of Advanced Micro/Nano Functional Materials, Department of Physics and Electronic Engineering, Xinyang Normal University, Xinyang 464000 (China); Xie, Changsheng [State Key Laboratory of Material Processing and Die & Mould Technology, Nanomaterials and Smart Sensors Research Laboratory, Department of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Xu, Jingjing; Luo, Yongsong; Wang, Chunlei; Yan, Hailong [Key Laboratory of Advanced Micro/Nano Functional Materials, Department of Physics and Electronic Engineering, Xinyang Normal University, Xinyang 464000 (China)

2015-10-05

Highlights: • Photoelectric responses of TiO{sub 2} and CdS/TiO{sub 2} to dry air and formaldehyde were tested. • In contrary to TiO{sub 2}, photoelectric response of CdS/TiO{sub 2} obviously increased. • CdS/TiO{sub 2} nanocomposite device exhibits excellent stability to formaldehyde. • CdS/TiO{sub 2} may be a promising material for developing high performance sensor. - Abstract: Photoelectric responses of pure TiO{sub 2} and CdS/TiO{sub 2} nanocomposite devices to dry air and formaldehyde under visible light irradiation at room temperature were investigated in this work. The pure TiO{sub 2} film was firstly prepared by screen printing and CdS/TiO{sub 2} nanocomposite film by the subsequent SILAR process. XRD, FE-SEM, HR-TEM and UV–vis DRS analysis were employed to examine the fundamental characteristics of as-prepared samples. Photoelectric responses of pure TiO{sub 2} device displayed that no obvious photocurrent was observed upon turning the visible light on either in dry air or in formaldehyde. But in contrary to pure TiO{sub 2} device, the photoelectric response of CdS/TiO{sub 2} nanocomposite device has been obviously enhanced. It is the adding of CdS, which works as a sensitizer, that accounts for the enhanced response and makes the CdS/TiO{sub 2} device sensitive to the visible light. Moreover, the CdS/TiO{sub 2} nanocomposite device exhibits excellent stability to formaldehyde. The present work does not only shed light on the photoelectric gas sensing properties of TiO{sub 2} and CdS/TiO{sub 2}, but also suggests that the CdS/TiO{sub 2} nanocomposite may be a promising material for fabricating visible-light-induced photoelectric gas sensors working at room temperature.

Study of TiC+TiN Multiple Films On Type of 316L Stainless Steel

Institute of Scientific and Technical Information of China (English)

XUE Qi; JIN Yong; HU Dong-ping; HUANG Ben-sheng; DENG Bai-quan

2004-01-01

In this paper, the synthesis process of TiC+TiN multiple films on super-low-carbon stainless steels is reported.The TiC layer is coated as the first layer in the multiple film, the change of growth rate of the film on the 316L Stainless steel is not same as the one on carbides substrates, while the mole ratio of CH4 to TiCl4 (mCH4/TiCl4) is changed from 1.2to 2.0. The Ti [C, N], as a kind of inter-layer between TiC and TiN layers, is helpful to improve the adhesion between the TiC and TiN layer. The cooling rate greatly influences the quality of the adhesion between the TiC+TiN film and substrates.

Study of TiC＋TiN Multiple Films On Type of 316L Stainless Steel

Institute of Scientific and Technical Information of China (English)

XUEQi; JINYong; HUDong-ping; HUANGBen-sheng; DENGBai-quan

2004-01-01

In this paper, the synthesis process of TiC+TiN multiple films on super-low-carbon stainless steels is reported. The TiC layer is coated as the first layer in the multiple film, the change of growth rate of the film on the 316L Stainlesss teel is not same as the one on carbides substrates, while the mole ratio of CH4 to TiCl4 (mCH4/TiCl4) is changed from 1.2 to 2.0. The Ti [C,N], as a kind of inter-layer between TiC and TiN layers, is helpful to improve the adhesion hetween the TiC and TiN layer. The cooling rate greatly influences the quality of the adhesion between the TiC+TiN film and substrates.

Significant enhancement in thermoelectric properties of polycrystalline Pr-doped SrTiO3−δ ceramics originating from nonuniform distribution of Pr dopants

KAUST Repository

Dehkordi, Arash Mehdizadeh

2014-05-12

Recently, we have reported a significant enhancement ( >70% at 500 °C) in the thermoelectric power factor (PF) of bulk polycrystalline Pr-doped SrTiO3 ceramics employing a novel synthesis strategy which led to the highest ever reported values of PF among doped polycrystalline SrTiO3. It was found that the formation of Pr-rich grain boundary regions gives rise to an enhancement in carrier mobility. In this Letter, we investigate the electronic and thermal transport in Sr1− x Pr x TiO3 ceramics in order to determine the optimum doping concentration and to evaluate the overall thermoelectric performance. Simultaneous enhancement in the thermoelectric power factor and reduction in thermal conductivity in these samples resulted in more than 30% improvement in the dimensionless thermoelectric figure of merit (ZT) for the whole temperature range over all previously reported maximum values. Maximum ZT value of 0.35 was obtained at 500 °C.

Significant enhancement in thermoelectric properties of polycrystalline Pr-doped SrTiO3−δ ceramics originating from nonuniform distribution of Pr dopants

KAUST Repository

Dehkordi, Arash Mehdizadeh; Bhattacharya, Sriparna; He, Jian; Alshareef, Husam N.; Tritt, Terry M.

2014-01-01

Recently, we have reported a significant enhancement ( >70% at 500 °C) in the thermoelectric power factor (PF) of bulk polycrystalline Pr-doped SrTiO3 ceramics employing a novel synthesis strategy which led to the highest ever reported values of PF among doped polycrystalline SrTiO3. It was found that the formation of Pr-rich grain boundary regions gives rise to an enhancement in carrier mobility. In this Letter, we investigate the electronic and thermal transport in Sr1− x Pr x TiO3 ceramics in order to determine the optimum doping concentration and to evaluate the overall thermoelectric performance. Simultaneous enhancement in the thermoelectric power factor and reduction in thermal conductivity in these samples resulted in more than 30% improvement in the dimensionless thermoelectric figure of merit (ZT) for the whole temperature range over all previously reported maximum values. Maximum ZT value of 0.35 was obtained at 500 °C.

Direct Z-scheme TiO2/CdS hierarchical photocatalyst for enhanced photocatalytic H2-production activity

Science.gov (United States)

Meng, Aiyun; Zhu, Bicheng; Zhong, Bo; Zhang, Liuyang; Cheng, Bei

2017-11-01

Photocatalytic H2 evolution, which utilizes solar energy via water splitting, is a promising route to deal with concerns about energy and environment. Herein, a direct Z-scheme TiO2/CdS binary hierarchical photocatalyst was fabricated via a successive ionic layer adsorption and reaction (SILAR) technique, and photocatalytic H2 production was measured afterwards. The as-prepared TiO2/CdS hybrid photocatalyst exhibited noticeably promoted photocatalytic H2-production activity of 51.4 μmol h-1. The enhancement of photocatalytic activity was ascribed to the hierarchical structure, as well as the efficient charge separation and migration from TiO2 nanosheets to CdS nanoparticles (NPs) at their tight contact interfaces. Moreover, the direct Z-scheme photocatalytic reaction mechanism was demonstrated to elucidate the improved photocatalytic performance of TiO2/CdS composite photocatalyst. The photoluminescence (PL) analysis of hydroxyl radicals were conducted to provide clues for the direct Z-scheme mechanism. This work provides a facile route for the construction of redox mediator-free Z-scheme photocatalytic system for photocatalytic water splitting.

Enhanced photocatalytic activity of SrTiO3 photocatalyst by topotactic preparation

Science.gov (United States)

Cao, Jiafeng; Huang, Xianshan; Liu, Yi; Wu, Jianguang; Ji, Yuexia

2016-11-01

Novel SrTiO3 (ST) photocatalysts with different shapes such as plates, rods and cubes were successfully synthesized based on a topotactic approach. The rod-like ST particles formed in situ at the plates show superior photocatalytic activities towards the decomposition of Rhodamine B than the plate-like and the cubic particles under visible-light irradiation, which could be attributed to the crystal orientation exposing highly active sites accompanied by the crystallite growth in molten salt. The results reveal an effective approach for fabrication of novel photocatalysts of perovskite structure with enhanced photocatalytic activities.

Ultrafast Flame Annealing of TiO2 Paste for Fabricating Dye-Sensitized and Perovskite Solar Cells with Enhanced Efficiency.

Science.gov (United States)

Kim, Jung Kyu; Chai, Sung Uk; Cho, Yoonjun; Cai, Lili; Kim, Sung June; Park, Sangwook; Park, Jong Hyeok; Zheng, Xiaolin

2017-11-01

Mesoporous TiO 2 nanoparticle (NP) films are broadly used as electrodes in photoelectrochemical cells, dye-sensitized solar cells (DSSCs), and perovskite solar cells (PSCs). State-of-the-art mesoporous TiO 2 NP films for these solar cells are fabricated by annealing TiO 2 paste-coated fluorine-doped tin oxide glass in a box furnace at 500 °C for ≈30 min. Here, the use of a nontraditional reactor, i.e., flame, is reported for the high throughput and ultrafast annealing of TiO 2 paste (≈1 min). This flame-annealing method, compared to conventional furnace annealing, exhibits three distinct benefits. First, flame removes polymeric binders in the initial TiO 2 paste more completely because of its high temperature (≈1000 °C). Second, flame induces strong interconnections between TiO 2 nanoparticles without affecting the underlying transparent conducting oxide substrate. Third, the flame-induced carbothermic reduction on the TiO 2 surface facilitates charge injection from the dye/perovskite to TiO 2 . Consequently, when the flame-annealed mesoporous TiO 2 film is used to fabricate DSSCs and PSCs, both exhibit enhanced charge transport and higher power conversion efficiencies than those fabricated using furnace-annealed TiO 2 films. Finally, when the ultrafast flame-annealing method is combined with a fast dye-coating method to fabricate DSSC devices, its total fabrication time is reduced from over 3 h to ≈10 min. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Photocatalytic activity of bipolar pulsed magnetron sputter deposited TiO{sub 2}/TiWO{sub x} thin films

Energy Technology Data Exchange (ETDEWEB)

Weng, Ko-Wei; Hu, Chung-Hsuan; Hua, Li-Yu; Lee, Chin-Tan [Department of Electronic Engineering, National Quemoy University, 1 Daxue Road, Jinning Township, Kinmen 89250, Taiwan, ROC (China); Zhao, Yu-Xiang [Department of Computer Science and Information Engineering, National Quemoy University, Taiwan, ROC (China); Chang, Julian; Yang, Shu-Yi [Department of Applied English, National Quemoy University, Taiwan, ROC (China); Han, Sheng, E-mail: shenghan@nutc.edu.tw [Center for General Education, National Taichung University of Science and Technology, 129 San-min Road, Section 3, Taichung 40401, Taiwan, ROC (China)

2016-08-15

Highlights: • TiO{sub 2}/TiWO{sub x} films were fabricated by a bipolar pulsed magnetron sputtering apparatus. • Titanium oxide being sputtered tungsten enhanced the highly oriented of TiO{sub 2} (1 0 1) plane of the specimen assemblies. • The mechanism WO{sub 3}(h{sup +}, e{sup −})/TiO{sub 2}(h{sup +}, e{sup −}) → WO{sub 3}(e{sup −})/TiO{sub 2}(h{sup +}) shows the higher hydrophilicity and lower contact angle. - Abstract: Titanium oxide films were formed by sputtering and then TiWO{sub x} films were deposited by bipolar pulsed magnetron sputtering with pure titanium and tungsten metal targets. The sputtering of titanium oxide with tungsten enhanced the orientation of the TiO{sub 2} (1 0 1) plane of the specimen assemblies. The main varying parameter was the tungsten pulse power. Titanium oxide sputtered with tungsten using a pulsing power of 50 W exhibited a superior hydrophilic property, and a contact angle of 13.1°. This fabrication conditions maximized the photocatalytic decomposition of methylene blue solution. The mechanism by which the titanium oxide was sputtered with tungsten involves the photogeneration of holes and electron traps, inhibiting the hole–electron recombination, enhancing hydrophilicity and reducing the contact angle.

Revelation of rutile phase by Raman scattering for enhanced photoelectrochemical performance of hydrothermally-grown anatase TiO2 film

Science.gov (United States)

Cho, Hsun-Wei; Liao, Kuo-Lun; Yang, Jih-Sheng; Wu, Jih-Jen

2018-05-01

Photoelectrochemical (PEC) performances of the anatase TiO2 films hydrothermally grown on the seeded fluorine-doped tin oxide (FTO) substrates are examined in this work. Structural characterizations of the TiO2 films were conducted using Raman scattering spectroscopy. Although there is no obvious rutile peak appearing, an asymmetrical peak centered at ∼399 cm-1 was observed in the Raman spectra of the TiO2 films deposited either on the low-temperature-formed seed layers or with low concentrations of Ti precursor. The asymmetrical Raman shift can be deconvoluted into the B1g mode of anatase and Eg mode of rutile TiO2 peaks centered at ∼399 cm-1 and ∼447 cm-1, respectively. Therefore, a minute quantity of rutile phase was inspected in the anatase film using Raman scattering spectroscopy. With the same light harvesting ability, we found that the PEC performance of the anatase TiO2 film was significantly enhanced as the minute quantity of rutile phase existing in the film. It is ascribed to the formation of the anatase/rutile heterojunction which is beneficial to the charge separation in the photoanode.

Ultrasound assisted combustion synthesis of TiC in Al-Ti-C system.

Science.gov (United States)

Liu, Zhiwei; Rakita, Milan; Xu, Wilson; Wang, Xiaoming; Han, Qingyou

2015-11-01

This research investigated the effects of high-intensity ultrasound on the combustion synthesis of TiC particles in Al-Ti-C system. The process involved that high-intensity ultrasound was applied on the surface of a compacted Al-Ti-C pellet directly through a Nb probe during the thermal explosion reaction. By comparing with the sample without ultrasonic treatment, it was found that the thermal explosion reaction for synthesizing TiC phase could take place thoroughly in the ultrasonically treated sample. During the process of synthesizing TiC phase, the dissolution of solid graphite particles into the Al-Ti melt, as well as the nucleation and growth of TiC particles could be promoted effectively due to the effects of ultrasound, leading to an enhancement of the formation of TiC particles. Ultrasound assisted combustion synthesis as a simple and effective approach was proposed for synthesizing materials in this research. Copyright © 2015 Elsevier B.V. All rights reserved.

Facile synthesis of a conjugation-grafted-TiO{sub 2} nanohybrid with enhanced visible-light photocatalytic properties from nanotube titanic acid precursors

Energy Technology Data Exchange (ETDEWEB)

Guo, Yanru; Zhang, Min, E-mail: zm1012@henu.edu.cn; Zhang, Zhihua; Li, Qiuye; Yang, Jianjun [Henan University, National and Local Joint Engineering Research Center for Applied Technology of Hybrid Nanomaterials (China)

2016-08-15

A conjugation-grafted-TiO{sub 2} nanohybrid was synthesized by chemically grafting conjugated structures on the surface of nanotube titanic acid (NTA) precursor-based TiO{sub 2} through the controlled thermal degradation of a coacervated polymer layer of polyvinyl alcohol (PVA). The interfacial interactions between the NTA precursor-based TiO{sub 2} and conjugated structures were characterized using Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Moreover, the effects of the NTA’s pretreatment temperature and the weight ratio of NTA to PVA on the photocatalytic degradation of methyl orange were also investigated. A higher NTA pretreatment temperature and a lower NTA to PVA weight ratio were found to enhance photogenerated electron–hole separation efficiency and photocatalytic activity. Moreover, the conjugation-grafted-TiO{sub 2} nanohybrid synthesized from the NTA precursor displayed a much higher visible-light photocatalytic activity than that of the sample obtained from the P25 precursor. The origin of the enhanced photocatalytic activity under visible-light irradiation is also discussed in detail.

Enhanced Power Conversion Efficiency of Perovskite Solar Cells with an Up-Conversion Material of Er3+-Yb3+-Li+ Tri-doped TiO2.

Science.gov (United States)

Zhang, Zhenlong; Qin, Jianqiang; Shi, Wenjia; Liu, Yanyan; Zhang, Yan; Liu, Yuefeng; Gao, Huiping; Mao, Yanli

2018-05-11

In this paper, Er 3+ -Yb 3+ -Li + tri-doped TiO 2 (UC-TiO 2 ) was prepared by an addition of Li + to Er 3+ -Yb 3+ co-doped TiO 2 . The UC-TiO 2 presented an enhanced up-conversion emission compared with Er 3+ -Yb 3+ co-doped TiO 2 . The UC-TiO 2 was applied to the perovskite solar cells. The power conversion efficiency (PCE) of the solar cells without UC-TiO 2 was 14.0%, while the PCE of the solar cells with UC-TiO 2 was increased to 16.5%, which presented an increase of 19%. The results suggested that UC-TiO 2 is an effective up-conversion material. And this study provided a route to expand the spectral absorption of perovskite solar cells from visible light to near-infrared using up-conversion materials.

Nitrogen implantation of Ti and Ti+Al films deposited on tool steel

International Nuclear Information System (INIS)

Huang, C.-T.; Duh, J.-G.

1995-01-01

Titanium and aluminum thin films were deposited onto A2 steel by rf magnetron sputtering with various Al contents. The coated assembly was then implanted with nitrogen ions at 92 kV and 1 mA for 4.5 h. The thickness of the implanted Ti and Ti+Al films deposited for 1 h was around 0.4-0.5 μm. With the aid of X-ray diffraction by the grazing-incidence technique, secondary ion mass spectrum (SIMS) and X-ray photoelectron spectroscopy (XPS), the titanium oxide and titanium nitride were identified on the top and inner surface in the implanted Ti film. For Ti+Al films after nitrogen implantation, Ti 3 O 5 was formed on the top surface beneath which is a (Ti, Al) N solid solution. There was Ti 2 N compound formed in the implanted Ti film, while only a minor amount of Ti 2 N phase was observed in the inner region in the implanted Ti+Al film. The nitrogen distribution was flattened and spread in the implanted Ti film, while a concentration gradient was observed in the Ti+Al film after implantation. The measured surface hardness of implanted Ti film was higher than those of Ti+Al films and the hardness of implanted Ti+39%Al film was enhanced as compared to the Ti+50%Al film. (Author)

Fabrication of A/R-TiO2 composite for enhanced photoelectrochemical performance: Solar hydrogen generation and dye degradation

Science.gov (United States)

Mahadik, Mahadeo A.; An, Gil Woo; David, Selvaraj; Choi, Sun Hee; Cho, Min; Jang, Jum Suk

2017-12-01

Anatase/rutile TiO2 nanorods composites were prepared by a facile hydrothermal method followed by dip coating method using titanium isopropoxide in acetic acid and ethanol solvent. The effects of the titanium isopropoxide precursor concentration, on the formation of dip coated anatase/rutile TiO2 nanorods composite were systematically explored. The growth of anatase on rutile TiO2 nanorods can be controlled by varying the titanium isopropoxide concentration. The morphological study reveals that anatase TiO2 nanograins formed on the surface of rutile TiO2 nanorod arrays through dip coating method. Photoelectrochemical analyses showed that the enhancement of the photocatalytic activities of the samples is affected by the anatase nanograins present on the rutile TiO2 nanorods, which can induce the separation of electrons and holes. To interpret the photoelectrochemical behaviors, the prepared photoelectrodes were applied in photoelectrochemical solar hydrogen generation and orange II dye degradation. The optimized photocurrent density of 1.8 mA cm-2 and the 625 μmol hydrogen generation was observed for 10 mM anatase/rutile TiO2 NRs composites. Additionally, 96% removal of the orange II dye was achieved within 5 h during oxidative degradation under solar light irradiation. One of the benefits of high specific surface area and the efficient photogenerated charge transport in the anatase/rutile TiO2 nanorod composite improves the photoelectrochemical hydrogen generation and orange dye degradation compared to the rutile TiO2. Thus, our strategy provides a promising, stable, and low cost alternative to existing photocatalysts and is expected to attract considerable attention for industrial applications.

Enhanced photoactivity of CuPp-TiO{sub 2} photocatalysts under visible light irradiation

Energy Technology Data Exchange (ETDEWEB)

Xiangfei, Lue [Key Laboratory of Synthetic and Natural Functional Molecule Chemistry of Ministry of Education, College of Chemistry and Materials Science, Northwest University, Xian, Shaanxi 710069 (China); Li Jun, E-mail: junli@nwu.edu.cn [Key Laboratory of Synthetic and Natural Functional Molecule Chemistry of Ministry of Education, College of Chemistry and Materials Science, Northwest University, Xian, Shaanxi 710069 (China); Chen, Wang; Mingyue, Duan; Yun, Luo; Guiping, Yao [Key Laboratory of Synthetic and Natural Functional Molecule Chemistry of Ministry of Education, College of Chemistry and Materials Science, Northwest University, Xian, Shaanxi 710069 (China); Junlong, Wang [Wei Nan Teachers University, Wei Nan, Shaanxi, 714000 (China)

2010-11-15

Three novel porphyrins, 5,10,15-tri-phenyl-20-[4-(3-phenoxy)-propoxy]phenyl porphyrin, 5,15-di-phenyl-10,20-di-[4-(3-phenoxy)-propoxy]phenyl porphyrin and 5-phenyl-10,15,20-tri- [4-(3-phenoxy)-propoxy]phenyl porphyrin, and their corresponding copper(II) complexes were synthesized and characterized spectroscopically. The photocatalytic effects of TiO{sub 2} samples impregnated with copper(II) porphyrins was investigated by photodegradation of 4-nitrophenol (4-NP) in aqueous solution under visible light. The photocatalysts were characterized by means of scanning electron microscopy (SEM), X-ray diffraction (XRD), UV-vis spectra and FT-IR spectra. The results indicated that CuPps were successfully loaded and interacted with the surface of TiO{sub 2} microsphere, which is crucial to enhance the activity of the catalytic composite under visible light.

Antibacterial activity and cell compatibility of TiZrN, TiZrCN, and TiZr-amorphous carbon coatings

Energy Technology Data Exchange (ETDEWEB)

Huang, Heng-Li [School of Dentistry, China Medical University, Taichung 404, Taiwan (China); Department of Bioinformatics and Medical Engineering, Asia University, Taichung 41354, Taiwan (China); Chang, Yin-Yu, E-mail: yinyu@nfu.edu.tw [Department of Mechanical and Computer-aided Engineering, National Formosa University, Yunlin 632, Taiwan (China); Liu, Jia-Xu [Department of Mechanical and Computer-aided Engineering, National Formosa University, Yunlin 632, Taiwan (China); Tsai, Ming-Tzu [Department of Biomedical Engineering, Hungkuang University, Taichung 433, Taiwan (China); Lai, Chih-Ho [Department of Microbiology and Immunology, Graduate Institute of Biomedical Sciences, Chang Gung University, Taoyuan, Taiwan (China)

2015-12-01

A cathodic-arc evaporation system with plasma-enhanced duct equipment was used to deposit TiZrN, TiZrCN, and TiZr/a-C coatings. Reactive gases (N{sub 2} and C{sub 2}H{sub 2}) activated by the Ti and Zr plasma in the evaporation process was used to deposit the TiZrCN and TiZr/a-C coatings with different C and nitrogen contents. The crystalline structures and bonding states of coatings were analyzed by X-ray diffraction and X-ray photoelectron spectroscopy. The microbial activity of the coatings was evaluated against Staphylococcus aureus (Gram-positive bacteria) and Actinobacillus actinomycetemcomitans (Gram-negative bacteria) by in vitro antibacterial analysis using a fluorescence staining method employing SYTO9 and a bacterial-viability test on an agar plate. The cell compatibility and morphology related to CCD-966SK cell-line human skin fibroblast cells on the coated samples were also determined using the 3-(4, 5-dimethylthiazol-2-yl)-2, 5-diphenyltetrazolium bromide assay, reverse-transcriptase-polymerase chain reaction, and scanning electron microscopy. The results suggest that the TiZrCN coatings not only possess better antibacterial performance than TiZrN and TiZr/a-C coatings but also maintain good compatibility with human skin fibroblast cells. - Highlights: • TiZrN, TiZrCN, and TiZr/a-C coatings were deposited using cathodic arc evaporation. • The TiZrCN showed a composite structure containing TiN, ZrN, and a-C. • The TiZrCN-coated Ti showed the least hydrophobicity among the samples. • The TiZrCN-coated Ti showed good human skin fibroblast cell viability. • The TiZrCN-coated Ti exhibited good antibacterial performance.

Effect Of Ti Powder Addition On The Fabrication Of TiO2 Nanopowders

Directory of Open Access Journals (Sweden)

Raihanuzzaman R.M.

2015-06-01

Full Text Available Sintered samples of Ti added TiO2 nanopowders were fabricated by combined application of magnetic pulsed compaction (MPC and sintering. The effect of Ti nano powder on density, shrinkage and hardness of the samples were investigated as part of the study. The optimum processing conditions were found to be around 0.5 GPa MPC pressure and 1450°C sintering temperature, illustrating maximum density, hardness and minimum shrinkage. High pressure compaction using MPC was found to enhance density with increasing MPC pressure up to 0.9 GPa, and significantly reduce the total shrinkage (about 16% in this case in the sintered bulks compared to other general processes (about 18%. While sintered samples blended with micro Ti showed presence of microstructural cracks, the samples with 1-2% nano Ti had less or no cracks on them. Overall, the inclusion of nano Ti indicated improvement in mechanical properties of TiO2 nanopowders sintered preforms as opposed to micro Ti-added TiO2.

Preparation, characterization and applications of novel carbon and nitrogen codoped TiO2 nanoparticles from annealing TiN under CO atmosphere

International Nuclear Information System (INIS)

Sun, Mingxuan; Song, Peng; Li, Jing; Cui, Xiaoli

2013-01-01

Graphical abstract: Carbon and nitrogen codoped TiO 2 nanoparticles were firstly fabricated by calcining TiN powder under CO atmosphere at different temperatures between 400 and 600 °C, both the improved photocatalytic activity for degradation of methylene blue and enhanced photovoltaic performance for dye sensitized solar cells were demonstrated. - Highlights: • CN-codoped TiO 2 nanoparticles were prepared by calcining TiN under CO atmosphere. • More visible light response was confirmed by UV–vis DRS and photocatalytic results. • Enhanced conversion efficiency was observed for the DSSCs from CN-TiO 2 photoanode. • CN-codoping played an important role to improve the photocatalytic performance. - Abstract: Carbon and nitrogen codoped titania (CN-TiO 2 ) nanoparticles were fabricated by calcining titanium nitride (TiN) nanoparticles under carbon monoxide (CO) atmosphere at four different temperatures in a range of 400–600 °C. The as-prepared samples were characterized with X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and X-ray photoelectron spectroscopy (XPS). Enhanced light absorption in both the UV and visible light region was observed for the resulted CN-TiO 2 nanoparticles in ultraviolet-visible diffuse reflectance spectroscopy (UV–vis DRS). Improved photocatalytic activity toward the degradation of methylene blue by the CN-TiO 2 nanoparticles was demonstrated under UV and visible light, respectively. The highest degradation rate was achieved for CN-TiO 2 nanoparticles (13%) compared to N-TiO 2 (10%) and the commercial P25 (5%) under visible light illumination for 40 min. Furthermore, the improved photocatalytic activity of CN-TiO 2 was also confirmed by the degradation of colorless resorcinol under UV–vis light irradiation. Dye-sensitized solar cells (DSSCs) were fabricated using P25, N-TiO 2 and CN-TiO 2 photoanodes, respectively. The highest conversion efficiency of 3.31% was achieved by the DSSCs based on the

Preparation of weak-light-driven TiO2-based catalysts via adsorbed-layer nanoreactor synthesis and enhancement of their photo-degradation performance in seawater

Science.gov (United States)

Wang, Ting; Xu, Zhi-yong; Zhu, Yi-chen; Wu, Li-guang; Yuan, Hao-xuan; Li, Chang-chun; Liu, Ya-yu; Cai, Jing

2017-11-01

Graphene oxide (GO) was first employed as a support in preparing TiO2 nanoparticles by adsorbed-layer nanoreactor synthesis (ALNS). Both TiO2 crystallization and GO reduction simultaneously occurred during solvothermal treatment with alcohol as a solvent. By transmission electron microscopy, high resolution transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and photoluminescence spectroscopy, the results showed that TiO2 nanoparticles with less than 10 nm of size distributed very homogeneously on the GO surface. Tight interaction between TiO2 particles and GO surface could effectively inhibit the aggregation of TiO2 particles, during solvothermal treatment for anatase TiO2 formation. Alcohol could also reduce oxygenated functional groups on GO surface after solvothermal treatment. TiO2 particles with small size and the decrease in oxygenated functional groups on the GO surface both caused high separation efficiency of photo-generated charge carriers, thus resulting in high photo-degradation performance of catalysts. Strong phenol adsorption on photocatalyst was key to enhancing photo-degradation efficiency for phenol in seawater. Moreover, the change in catalyst structure was minimal at different temperatures of solvothermal treatment. But, the degradation rate and efficiency for phenol in seawater were obviously enhanced because of the sensitive structure-activity relationship of catalysts under weak-light irradiation.

Synthesis of ascorbic acid enhanced TiO2 photocatalyst: its characterization and catalytic activity in CO2 photoreduction

Directory of Open Access Journals (Sweden)

Mohd Farid Bin Mohd Na'aim

2018-04-01

Full Text Available To date, the development of solar environmental remediation has shifted more emphasis on the green and simple synthesis of catalyst for CO2 photocatalysis process. Herein, TiO2 photocatalyst was successfully synthesized via hydrothermal method. The effects of the different molar ratio of ascorbic acid C6H8O6, (AA added during the preparation of TiO2 nanoparticles were comprehensively studied. The characterization of TiO2 nanocrystals was performed via XRD, XPS, DRUV-vis, and FTIR. The results show the AA loading into TiO2 nanoparticles significantly intensified the XRD spectra of anatase structure. In fact, this feature had signified a reactivity of the photocatalyst in the visible region. In an instance, BET surface area was also enhanced with the highest recorded value of 135.14 m2/g for 0.8AA. Meanwhile, the CO2 photoreduction over synthesized TiO2 had produced the highest amount of HCOOH at 39.3 μmol/g cat for 0.8AA within 6 hours of reaction time. Furthermore, the DRUV-vis analysis had illustrated better light absorption ability of 0.8AA. This profound finding is attributed to the correlation between large surface area, pure anatase phase, and high adsorbed water molecules. Therefore, this study had significantly demonstrated the potential of modified TiO2 with AA in CO2 photocatalysis area while simultaneously presents a green and simple method for TiO2 synthesis.

Evaluation of prakṛti and quality-of-life in patients with irritable bowel syndrome

Science.gov (United States)

Shirolkar, Sudatta G.; Tripathi, Raakhi K.; Rege, Nirmala N.

2015-01-01

Objective: To evaluate the prakṛti of irritable bowel syndrome (IBS) patients and its association with IBS subtypes and quality-of-life (QOL). Methodology: IBS patients with the consistent subtype in the last 6 months were recruited. Prakṛti assessment with a 24-item questionnaire was performed and depending on the scores the patients were categorized into vāta predominant, pitta predominant, and kapha predominant prakṛti. QOL was assessed with prevalidated disease-specific 34-item questionnaire scored on a 0–100 scale. Results: Of 50 IBS patients enrolled, with mean age of 43.5 ± 12.8 years, and male: female as 43:7, 22 patients were of vāta and pitta predominant prakṛti each while six patients had kapha predominant prakṛti. IBS-C was diagnosed in 24 patients, IBS-D in 21, and IBS-M in five patients. In vāta predominant group, IBS-C was found in 13 patients, IBS-D in 8, and IBS-M in 1. In pitta predominant group, IBS-D was found in 13, IBS-C in 6, and IBS-M in 3. In kapha predominant group, IBS-C was found in 5 patients and IBS-M in 1. The median QOL in IBS-C group was 48.897, IBS-D was 38.97, and IBS-M was 66.911. The median QOL score 52.205, 42.27, and 55.51 in vāta, pitta, and kapha predominant group, respectively. Conclusion: Majority of the vāta predominant patients had developed IBS-C, pitta predominant patients had developed IBS-D. QOL was better in pitta predominant individuals of all IBS-disease subtypes. With this, we find that prakṛti examination in IBS helps in detecting the proneness of developing an IBS subtype and predicting their QOL accordingly. PMID:26283806

Ternary Hollow Mesoporous TiN/N-Graphene/Pt Hybrid Results in Enhanced Electrocatalytic Performance for Methanol Oxidation and Oxygen Reduction Reaction

International Nuclear Information System (INIS)

Liu, Baocang; Huo, Lili; Zhang, Geng; Zhang, Jun

2016-01-01

Highlights: • A novel hollow mesoporous ternary @M-TiN/N-G/Pt electrocatalysts were synthesized. • The @M-TiN/N-G/Pt electrocatalysts displayed outstanding activity and stability toward MOR and ORR. • The activity and stability of @M-TiN/N-G/Pt electrocatalysts were higher than Pt/TiN, @M-TiN/Pt, and Pt/C catalysts. • The excellent electrocatalytic performance rooted in its unique configuration. • Several reasons were proposed to explain the enhanced electrocatalytic performance of @M-TiN/N-G/Pt. - Abstract: A novel hollow mesoporous TiN/N-graphene (N-G) hybrid architecture (@M-TiN/N-G) composed of N-doped graphene wrapped mesoporous TiN nanoparticle shells was constructed for the first time. It can be used as an efficient support for creating a highly efficient ternary @M-TiN/N-G/Pt electrocatalyst with superior catalytic activity and stability for methanol oxidation reaction (MOR) and oxygen reduction reaction (ORR) through decorating well-dispersed Pt nanoparticles on @M-TiN/N-G surface. By optimizing the content of N-G in catalysts, the @M-TiN/N-G/Pt catalysts display superior catalytic activity and stability toward MOR and ORR to traditional Pt/C and graphene-free Pt/TiN and @M-TiN/Pt catalysts. The various characterization results reveal that the outstanding electrocatalytic performance of @M-TiN/N-G/Pt catalyst roots in its large surface area, high porosity, strong interaction among Pt, TiN, and N-G, excellent electron transfer property facilitated by N-doped graphene, and small size of Pt and TiN nanocrystals. The synthetic approach may be available for constructing other graphene based hollow metal nitrides, carbides, and phosphides for various electrocatalytic applications.

Surface passivation of nano-textured fluorescent SiC by atomic layer deposited TiO2

DEFF Research Database (Denmark)

Lu, Weifang; Ou, Yiyu; Jokubavicius, Valdas

2016-01-01

Nano-textured surfaces have played a key role in optoelectronic materials to enhance the light extraction efficiency. In this work, morphology and optical properties of nano-textured SiC covered with atomic layer deposited (ALD) TiO2 were investigated. In order to obtain a high quality surface fo...

Fabrication of novel Ag−TiO{sub 2} nanobelts as a photoanode for enhanced photovoltage performance in dye sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Wang, Yang [Engineering Research Center of Nano-Geomaterials of Ministry of Education, China University of Geosciences, Wuhan 430074 (China); Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Li, Zhen, E-mail: zhenli@cug.edu.cn [Engineering Research Center of Nano-Geomaterials of Ministry of Education, China University of Geosciences, Wuhan 430074 (China); Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Cao, Ya; Li, Fei; Zhao, Wen; Liu, Xueqin; Yang, Jianbo [Engineering Research Center of Nano-Geomaterials of Ministry of Education, China University of Geosciences, Wuhan 430074 (China); Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China)

2016-08-25

TiO{sub 2} nanobelts (TiO{sub 2}NBs) were successfully prepared using a solvothermal route via Ti foil as substrate in large scales. The morphology evolution process and formation mechanism of the as-obtained products were investigated in detail. On the basis of this novel structure, chemical sensitive Ag modified TiO{sub 2}NBs nanocomposites (Ag−TiO{sub 2}NBs) were fabricated. It was found that Ag−TiO{sub 2}NBs exhibit strong light absorption and efficient electron transport. According to Mott-Schottky analysis, Ag−TiO{sub 2}NBs show less surface trapping sites compared with TiO{sub 2}NBs. The Ag−TiO{sub 2}NBs photoanode fabricated in 0.01 M AgNO{sub 3} demonstrates the best performance with a short-circuit current of 11.9 mA cm{sup −2} corresponding to a photoelectric conversion efficiency of 4.89%, which is higher than that of pure TiO{sub 2}NBs based solar cell by 60%. - Graphical abstract: J-V curves of DSSCs based on TiO{sub 2}NPs, TiO{sub 2}NBs and Ag−TiO{sub 2}NBs—X under AM 1.5 conditions (100 mW cm{sup −2}). Ag−TiO{sub 2}NBs nanocomposites were prepared via a simple and effective method. Owing to strong light absorption and efficient electron transport, Ag−TiO{sub 2}NBs—0.01 M shows a PCE of 4.89% when prepared as a photoanode in DSSCs. - Highlights: • A facile route was adopted to construct well-dispersed Ag nanoparticles on TiO{sub 2} nanobelts (Ag—TiO{sub 2}NBs). • Structure and photoelectrochemical properties of Ag—TiO{sub 2}NBs were studied. • Ag nanoparticles were found to modify the defects of TiO{sub 2}NBs. • Enhanced photovoltaic property of Ag—TiO{sub 2}NBs, compared to TiO{sub 2}NBs.

Interface engineering of CsPbBr3/TiO2 heterostructure with enhanced optoelectronic properties for all-inorganic perovskite solar cells

Science.gov (United States)

Qian, Chong-Xin; Deng, Zun-Yi; Yang, Kang; Feng, Jiangshan; Wang, Ming-Zi; Yang, Zhou; Liu, Shengzhong Frank; Feng, Hong-Jian

2018-02-01

Interface engineering has become a vital method in accelerating the development of perovskite solar cells in the past few years. To investigate the effect of different contacted surfaces of a light absorber with an electron transporting layer, TiO2, we synthesize CsPbBr3/TiO2 thin films with two different interfaces (CsBr/TiO2 and PbBr2/TiO2). Both interfacial heterostructures exhibit enhanced visible light absorption, and the CsBr/TiO2 thin film presents higher absorption than the PbBr2/TiO2 interface, which is attributed to the formation of interface states and the decreased interface bandgap. Furthermore, compared with the PbBr2/TiO2 interface, CsBr/TiO2 solar devices present larger output short circuit current and shorter photoluminescence decay time, which indicates that the CsBr contacting layer with TiO2 can better extract and separate the photo-induced carriers. The first-principles calculations confirm that, due to the existence of staggered gap (type II) offset junction and the interface states, the CsBr/TiO2 interface can more effectively separate the photo-induced carriers and thus drive the electron transfer from the CsPbBr3 perovskite layer to the TiO2 layer. These results may be beneficial to exploit the potential application of all-inorganic perovskite CsPbBr3-based solar cells through the interface engineering route.

Synthesis and characterization of insulin/zirconium phosphate@TiO2 hybrid composites for enhanced oral insulin delivery applications.

Science.gov (United States)

Safari, Mostafa; Kamari, Younes; Ghiaci, Mehran; Sadeghi-Aliabadi, Hojjat; Mirian, Mina

2017-05-01

In this work, a series of composites of insulin (Ins)/zirconium phosphate (ZrP) were synthesized by intercalation method, then, these composites were coated with TiO 2 by sol-gel method to prepare Ins/ZrP@TiO 2 hybrid composites and the drug release of the composites was investigated by using UV-Vis spectroscopy. Ins/ZrP (10, 30, 60 wt%) composites were prepared by intercalation of insulin into the ZrP layers in water. Then Ins/ZrP composites were coated with different amounts of TiO 2 (30, 50, 100 wt %) by using titanium tetra n-butoxide, as precursor. Formation of intercalated Ins/ZrP and Ins/ZrP@TiO 2 hybrid composites was characterized by FT-IR, FE-SEM, BET and XRD analysis. Zeta potential of the optimized Ins/ZrP@TiO 2 hybrid composite was determined -27.2 mV. Cytotoxic effects of the optimized Ins/ZrP@TiO 2 hybrid composite against HeLa and Hek293T cell lines were evaluated using MTT assay and the results showed that designed drug delivery system was not toxic in biological environment. Compared to the Ins/ZrP composites, incorporation of TiO 2 coating enhanced the drug entrapment considerably, and reduced the drug release. The Ins/ZrP composites without TiO 2 coating released the whole drug after 30 min in pH 7.4 (phosphate buffer solution) while the TiO 2 -coated composites released the entrapped drug after 20 h. In addition to increasing the shelf life of hormone, this nanoencapsulation and nanocoating method can convert the insulin utilization from injection to oral and present a painless and more comfortable treatment for diabetics.

Pressure-composition isotherms and thermodynamic properties of TiF3-enhanced Na2LiAlH6

International Nuclear Information System (INIS)

Fossdal, A.; Brinks, H.W.; Fonnelop, J.E.; Hauback, B.C.

2005-01-01

The mixed alanate Na 2 LiAlH 6 was prepared by ball-milling and subsequent heat-treatment under H 2 pressure. After the synthesis, 2 mol% TiF 3 was added by ball-milling. Pressure-composition isotherms were measured for the Ti-enhanced material in the temperature range of 170-250 deg C. A van't Hoff plot was constructed using the equilibrium desorption plateau pressures. From this plot, a dissociation enthalpy of 56.4 ± 0.4 kJ/mol H 2 and a corresponding entropy of 137.9 ± 0.7 J/K mol H 2 was found for Na 2 LiAlH 6

Synergetic effect of Ag_2O as co-catalyst for enhanced photocatalytic degradation of phenol on N-TiO_2

International Nuclear Information System (INIS)

Chu, Haipeng; Liu, Xinjuan; Liu, Junying; Li, Jinliang; Wu, Tianyang; Li, Haokun; Lei, Wenyan; Xu, Yan; Pan, Likun

2016-01-01

Graphical abstract: Ag_2O/N-TiO_2 composites were synthesized via a co-precipitation method for visible light photocatalytic degradation of organic pollutions with excellent photocatalytic activity. - Highlights: • Ag_2O/N-TiO_2 composites were synthesized via a facile precipitation method. • Ag_2O/N-TiO_2 composites exhibited enhanced photocatalytic activity. • Ag_2O acts as co-catalyst to separate the photo-generated electron-hole pairs. - Abstract: A facile precipitation method was developed to synthesize the Ag_2O/N-TiO_2 composites. Their morphology, structure and photocatalytic performance in the degradation of methylene blue (MB) and phenol under visible light irradiation were characterized by scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, photoluminescence spectroscopy and UV–vis absorption spectroscopy, respectively. The results show that the Ag_2O/N-TiO_2 composites exhibit excellent photocatalytic performance. The maximum degradation rates of MB and phenol are about 8.9 and 2.9 times that of pure N-TiO_2, respectively. The excellent photocatalytic performance is mainly ascribed to the synergetic effects of Ag_2O and N-TiO_2 including the increased light absorption and the reduced electron-hole pair recombination in N-TiO_2 with the presence of Ag_2O.

New insight for enhancing photocatalytic activity of MWCNT/TiO{sub 2} by decorating palladium nanoparticles as charge-transfer channel

Energy Technology Data Exchange (ETDEWEB)

Zhang, Feng-Jun, E-mail: zhang-fengjun@hotmail.com [School of Materials and Chemical Engineering, Anhui University of Architecture, Anhui Hefei 230022 (China); Department of Advanced Materials and Science Engineering, Hanseo University, Seosan-si, Chungnam-do 356-706 (Korea, Republic of); Oh, Won-Chun, E-mail: wc_oh@hanseo.ac.kr [Department of Advanced Materials and Science Engineering, Hanseo University, Seosan-si, Chungnam-do 356-706 (Korea, Republic of); Zhang, Kan [Department of Advanced Materials and Science Engineering, Hanseo University, Seosan-si, Chungnam-do 356-706 (Korea, Republic of); Center for Superfunctional Materials, Department of Chemistry, Pohang University of Science and Technology, Hyojadong, Namgu, Pohang 790-784 (Korea, Republic of)

2012-03-15

Highlights: Black-Right-Pointing-Pointer A new insight for further improving photoactivity of MWCNT/TiO{sub 2} was reported. Black-Right-Pointing-Pointer The Pd as charge transfer channel trap electrons from MWCNT to TiO{sub 2} surface. Black-Right-Pointing-Pointer The Pd content can also influence photoactivity of MWCNT/TiO{sub 2} photocatalyst. Black-Right-Pointing-Pointer The approach is practically usable for other nanocarbon/semiconductor materials. -- Abstract: A surface bond-grafted multi-walled carbon nanotube (MWCNT)/TiO{sub 2} as supporter, palladium nanoparticles, approximately 3 nm in diameter, are uniformly deposited on the functional MWCNT surface in first, constructing a novel Pd-MWCNT/TiO{sub 2} photocatalyst for photocatalytic solar conversion. The characterization of photocatalysts by a series of joint techniques, including BET surface area, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), energy dispersive X-ray (EDX), Raman spectroscopy and ultraviolet/visible (UV/vis) diffuse reflectance spectra, discloses that palladium nanoparticles has a crucial role in enhancement of photocatalytic activity of MWCNT/TiO{sub 2}, that is to act as a charge transfer channel, which helps to trap electrons from MWCNT to TiO{sub 2}.

Comparing Cr, and N only doping with (Cr,N)-codoping for enhancing visible light reactivity of TiO2

International Nuclear Information System (INIS)

Li, Yuan; Wang, Wei; Qiu, Xiaofeng; Meyer, Harry M. III; Paranthaman, Mariappan Parans; Eres, Gyula; Zhang, Zhenyu; Gu, Baohua

2011-01-01

The photoreactivity of titania (TiO2) nanoclusters with varying levels of N or Cr-doping, or (Cr,N)-codoping, was systematically investigated using photodegradation of methyl orange in aqueous suspensions. The shifting of the TiO2 absorption edge into the visible spectral region that is primarily attributable to band gap narrowing was found to be a reliable metric for estimating the photoreactivity of the doped nanoclusters. Compared to the weak response with undoped and N-doped TiO2, Cr-doping and (Cr, N)-codoping were found to significantly enhance photodegradation of methyl orange under visible light. The initial reaction rates increase from about 0 to above 1.6 10-2 min-1 when the doping concentration of Cr in TiO2 increases from 0 to 5%. In stark contrast, under UV irradiation, doping is not only ineffective but detrimental to the photoreactivity, and all doping including N or Cr only and (Cr, N)-codoping were found to reduce photoreactivity.

Change of Dye Bath for Sensitisation of Nanocrystalline TiO Films: Enhances Performance of Dye-Sensitized Solar Cells

Directory of Open Access Journals (Sweden)

Malapaka Chandrasekharam

2011-01-01

Full Text Available The photovoltaic performance of the heteroleptic H102 and HRD2 sensitizers was measured in DSSC and compared with that of reference N719 under similar fabrication and evaluation conditions. The Dye-Sensitised TiO2 electrodes were prepared by staining the electrodes in ethanol bath and 1/1 v/v acetonitrile/tert-butanol (binary liquid mixture bath separately and the DSSCs based on these sensitizers show that the change of dye bath from ethanol to the binary liquid mixture enhances the photocurrent action spectrum and solar-to-electricity conversion efficiencies, (η. Using ethanol for sensitisation of TiO2 electrodes, the efficiencies obtained for H102, HRD2 and N719 are 4.31%, 4.62%, and 5.46%, respectively, while in binary liquid mixture bath, the corresponding values are enhanced to 5.89%, 4.87%, and 7.23%, respectively, under comparable conditions.

Enhancing the efficiency of dye-sensitized solar cells by adding diatom frustules into TiO{sub 2} working electrodes

Energy Technology Data Exchange (ETDEWEB)

Huang, Der-Ray, E-mail: derray@mail.ndhu.edu.tw; Jiang, Yan-Jang; Liou, Run-Lin; Chen, Chih-Han; Chen, Yi-An; Tsai, Chih-Hung, E-mail: cht@mail.ndhu.edu.tw

2015-08-30

Graphical abstract: - Highlights: • High-speed centrifugal processing and sedimentation-rate separation techniques were used to obtain diatom frustules. • Diatom frustules were added into TiO{sub 2} paste to prepare a TiO{sub 2}-diatom paste mixture. • TiO{sub 2}-diatom paste mixture was used to fabricate working electrodes for DSSCs. • TiO{sub 2}-diatom electrodes improved the light-trapping effect and DSSC efficiency. • DSSCs with using the TiO{sub 2}-diatom electrode exhibited a 38% increase in efficiency. - Abstract: In this study, diatom frustules were added into TiO{sub 2} paste to prepare a TiO{sub 2}-diatom paste mixture. Spin-coating and high-temperature sintering techniques were then used to fabricate working electrodes for dye-sensitized solar cells (DSSCs). Mixing the diatom frustules with the TiO{sub 2} paste improved the light-trapping effect and scattering properties of the incident light in the TiO{sub 2}-diatom working electrodes, thereby enhancing the power conversion efficiency of the DSSCs. In this study, a high-speed centrifugal processing technology and sedimentation-rate separation techniques were first used to obtain the diatom frustules, which were then mixed with the TiO{sub 2} paste at a weight ratio of 1:50; a spin-coating technique was then used to fabricate the working electrodes. Finally, a high-temperature sintering process (500 °C) was performed. In this study, optical microscopy, scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, and a surface profiler and spectrometer were used to analyze the characteristics of the working electrodes. The TiO{sub 2} or TiO{sub 2}-diatom working electrodes were prepared under various spin-coating conditions for fabricating and analyzing the characteristics of the DSSCs. The results indicated that under identical conditions, the power conversion efficiency of the DSSCs was 3.81% when coated three times with a conventional TiO{sub 2

Preparation and characterization of RF magnetron sputtered CuO/CaTi{sub 4}O{sub 9} thin films with enhanced third-order nonlinear optical properties

Energy Technology Data Exchange (ETDEWEB)

Yin, Congfei; Liang, Xiaojuan, E-mail: lxj6126@126.com; Hu, Guangcai; Hu, Xie; Chen, Xipeng; Li, Pengzhi; Xiang, Weidong, E-mail: xiangweidong001@126.com

2017-04-15

The titanate, is a material of interest for various energy applications, including photovoltaics, catalysts, and high-rate energy storage devices. Herein, its related materials, CuO/CaTi{sub 4}O{sub 9} [CCTO] thin films, were successfully fabricated on SrTiO{sub 3} (100) substrates by RF magnetron sputtering assisted with subsequent oxygen annealing. This obtained CCTO thin films were then systemically studied by X-ray powder diffraction (XRD), atomic force microscopy (AFM), scan electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and high-resolution transmission electron microscopy (HRTEM). It was found that CuO and CaTi{sub 4}O{sub 9} (001) particles were closely accumulated together on the surface of the substrate in the annealing process after comparing with that of the as-prepared thin film, which was verified by SEM and AFM results. Furthermore, we investigated the third-order nonlinear optical (NLO) properties of the as-prepared and annealed CCTO thin film by means of the Z-scan technique using 650 nm femtosecond laser pulse. Post-deposition oxygen annealing was found to modify the morphological characteristics of the films, resulting in enhancing their NLO properties. The observation of NLO performance of annealed CCTO thin film indicates that RF magnetron sputtering is a feasible method for the fabrication of optical thin films, which can be expanded to fabricate other NLO materials from the corresponding dispersions. Naturally, we concluded that the CCTO thin film occupy a better NLO property, and thus enlarge its application in nonlinear optics. - Highlights: • The CCTO thin film was prepared using the RF magnetron sputtering and oxygen annealing. • The film was prepared on the SrTiO{sub 3}(100) substrates with a Ca{sub 2}CuO{sub 3} target. • The oxygen annealing was found can effectively enhance the film quality and NLO property. • The film was characterized using XPS, SEM, AFM, TEM, XRD and Z-scan techniques.

HVOF-Sprayed Nano TiO2-HA Coatings Exhibiting Enhanced Biocompatibility

Science.gov (United States)

Lima, R. S.; Dimitrievska, S.; Bureau, M. N.; Marple, B. R.; Petit, A.; Mwale, F.; Antoniou, J.

2010-01-01

Biomedical thermal spray coatings produced via high-velocity oxy-fuel (HVOF) from nanostructured titania (n-TiO2) and 10 wt.% hydroxyapatite (HA) (n-TiO2-10wt.%HA) powders have been engineered as possible future alternatives to HA coatings deposited via air plasma spray (APS). This approach was chosen due to (i) the stability of TiO2 in the human body (i.e., no dissolution) and (ii) bond strength values on Ti-6Al-4V substrates more than two times higher than those of APS HA coatings. To explore the bioperformance of these novel materials and coatings, human mesenchymal stem cells (hMSCs) were cultured from 1 to 21 days on the surface of HVOF-sprayed n-TiO2 and n-TiO2-10 wt.%HA coatings. APS HA coatings and uncoated Ti-6Al-4V substrates were employed as controls. The profiles of the hMSCs were evaluated for (i) cellular proliferation, (ii) biochemical analysis of alkaline phosphatase (ALP) activity, (iii) cytoskeleton organization (fluorescent/confocal microscopy), and (iv) cell/substrate interaction via scanning electron microscopy (SEM). The biochemical analysis indicated that the hMSCs cultured on n-TiO2-10 wt.%HA coatings exhibited superior levels of bioactivity than hMSCs cultured on APS HA and pure n-TiO2 coatings. The cytoskeleton organization demonstrated a higher degree of cellular proliferation on the HVOF-sprayed n-TiO2-10wt.%HA coatings when compared to the control coatings. These results are considered promising for engineering improved performance in the next generation of thermally sprayed biomedical coatings.

Enhancement in photo-electrochemical efficiency by reducing recombination rate in branched TiO2 nanotube array on functionalizing with ZnO micro crystals

Science.gov (United States)

Boda, Muzaffar Ahmad; Ashraf Shah, Mohammad

2018-06-01

In this study, branched TiO2 nanotube array were fabricated through electrochemical anodization process at constant voltage using third generation electrolyte. On account of morphological advantage, these nanotubes shows significant enhancement in photo-electrochemical property than compact or conventional titania nanotube array. However, their photo-electrochemical efficiency intensifies on coating with ZnO micro-crystals. ZnO coated branched TiO2 nanotube array shows a photocurrent density of 27.8 mA cm‑2 which is 1.55 times the photocurrent density (17.2 mA cm‑2) shown by bare branched titania nanotubes. The significant enhancement in photocurrent density shown by the resulting ZnO/TiO2 hybrid structure is attributed to suppression in electron–hole recombination phenomenon by offering smooth pathway to photo generated excitons on account of staggered band edge positions in individual semiconductors.

Core/Shell Structured TiO2/CdS Electrode to Enhance the Light Stability of Perovskite Solar Cells.

Science.gov (United States)

Hwang, Insung; Baek, Minki; Yong, Kijung

2015-12-23

In this work, enhanced light stability of perovskite solar cell (PSC) achieved by the introduction of a core/shell-structured CdS/TiO2 electrode and the related mechanism are reported. By a simple solution-based process (SILAR), a uniform CdS shell was coated onto the surface of a TiO2 layer, suppressing the activation of intrinsic trap sites originating from the oxygen vacancies of the TiO2 layer. As a result, the proposed CdS-PSC exhibited highly improved light stability, maintaining nearly 80% of the initial efficiency after 12 h of full sunlight illumination. From the X-ray diffraction analyses, it is suggested that the degradation of the efficiency of PSC during illumination occurs regardless of the decomposition of the perovskite absorber. Considering the light-soaking profiles of the encapsulated cells and the OCVD characteristics, it is likely that the CdS shell had efficiently suppressed the undesirable electron kinetics, such as trapping at the surface defects of the TiO2 and preventing the resultant charge losses by recombination. This study suggests that further complementary research on various effective methods for passivation of the TiO2 layer would be highly meaningful, leading to insight into the fabrication of PSCs stable to UV-light for a long time.

Noble metal-free RGO/TiO2 composite nanofiber with enhanced photocatalytic H2-production performance

Science.gov (United States)

Xu, Difa; Li, Lingling; He, Rongan; Qi, Lifang; Zhang, Liuyang; Cheng, Bei

2018-03-01

1D reduced graphene oxide (RGO)/TiO2 nanocomposite fibers were fabricated by a facile two-step method. These samples demonstrated high photocatalytic H2-production activity from methanol aqueous solution, even without the aid of noble metal. When the ratio of RGO is 0.25 wt%, the highest H2-production rate was achieved. It increased by 10 fold than bare TiO2, reaching 149 μmol h-1 g-1 with quantum efficiency (QE) of 0.75%. The reasons were as follows. Firstly, the RGO nanosheets acted as electron acceptors. Secondly, some shallow trap states at the surface or interface of TiO2 were created by the reduction of GO during calcination. Thirdly, the redox potential position of graphene/graphene- was suitable. Fourthly, RGO could efficiently promote the separation of photogenerated electron-hole pairs and significantly enhance the photocatalytic H2-production activity. This interpretation was corroborated by transient photocurrent response. The aforementioned marvelous results provided a probable solution to replace noble metals (such as Pt) by graphene as an effective cocatalyst.

Enhanced flux creep in Nb-Ti superconductors after an increase in temperature

International Nuclear Information System (INIS)

Cross, R.W.; Goldfarb, R.B.

1991-01-01

The magnetic fields of Superconducting Super Collider (SSC) dipole magnets change with time when the magnets are operated at constant current. The decay of the field is thought to be a consequence of flux creep in the Nb-Ti filaments in the superconducting cables. However, measured magnetic relaxation of small samples of SSC cable as a function of time is unlike the large decays that are observed in the fields of the actual magnets. We have made relaxation measurements on sample SSC conductors at 3.5 and 4.0 K after field cycling. The decay at both temperatures was 2.8% in 50 min. However, the relaxation measured after a temperature increase from 3.5 to 4.0 K was 4.8% in 50 min. A likely reason for the greater magnetization decay is that, after an increase in temperature, the Nb-Ti is in a supercritical state, with shielding currents flowing at a density greater than the new critical current density. This causes enhanced flux creep. We suggest that a small temperature rise during the operation of SSC magnets may contribute to the unexpectedly large magnetic field decay

Electronic Structures and Bonding Properties of Ti2AlC and Ti3AlC2

Institute of Scientific and Technical Information of China (English)

MIN Xinmin; REN Yi

2007-01-01

The relation among electronic structure, chemical bond and property of Ti2AlC, Ti3AlC2 and doping Si into Ti2AlC was studied by density function and the discrete variation (DFT-DVM) method. After adding Si into Ti2AlC, the interaction between Si and Ti is weaker than that between Al and Ti, and the strengths of ionic and covalent bonds decrease both. The ionic and covalent bonds in Ti3AlC2, especially in Ti-Al, are stronger than those in Ti2AlC. Therefore, in synthesis of Ti2AlC, the addition of Si enhances the Ti3AlC2 content instead of Ti2AlC. The density of state (DOS) shows that there is mixed conductor characteristic in Ti2AlC and Ti3AlC2. The DOS of Ti3AlC2 is much like that of Ti2AlC. Ti2SixAl1-x C has more obvious tendency to form a semiconductor than Ti2AlC, which is seen from the obvious difference of partial DOS between Si and Al3p.

Photoelectrocatalytic property of microporous Pt-TiO2/Ti electrodes

International Nuclear Information System (INIS)

Hung, Chung-Hsuang; Wu, Kee-Rong; Yeh, Chung-Wei; Sun, Jui-Ching; Hsu, Chuan-Jen

2013-01-01

This study investigates the photoelectrocatalytic (PEC) property of microporous WO 3 -loaded TiO 2 /Ti layer, prepared via micro-arc oxidation (MAO) of Ti plate, followed by sputtering deposition of a thin Pt layer as a Pt-TiO 2 /Ti electrode. The WO 3 -loaded TiO 2 layer which is associated with a more acidic surface forms many local electrochemical cells on its micro-pores immersed in cationic dye solution. The electrocatalytic (EC) reactions can take place in the local cells by the applied electrons. A low resistivity that is accomplished by MAO technique and by platinization offers an easy path for the electron motions in the Pt-TiO 2 /Ti electrode. All these features make the EC oxidation of aqueous dye pollutants practically feasible without using counter electrodes and supporting electrolytes. Our experiments demonstrate that, under PEC condition, the Pt-TiO 2 /Ti shows the highest degradation rate constant of 0.83 h − 1 at an applied bias of 1.0 V and exhibits significantly high PEC and EC oxidation activities at a low applied bias of 0.25 V. This is attributable to high anodic currents generated in the Pt-TiO 2 /Ti even at low bias. The modified microporous electrodes conclusively reveal a very interesting EC property as a two double-sided device that functions the PEC and EC oxidation simultaneously without a need of supporting electrolyte and expensive Pt cathode. - Highlights: ► Pt-TiO 2 /Ti exhibits enhanced photoelectrocatalytic (PEC) activity at low applied bias. ► The proposed device uses low applied bias (< 1.0 V) with no explicit cathode. ► PEC oxidation can be performed without supporting electrolyte and Pt cathode

Enhanced electrochemical performance of Ti substituted P2-Na2/3Ni1/4Mn3/4O2 cathode material for sodium ion batteries

International Nuclear Information System (INIS)

Zhao, Wenwen; Tanaka, Akinobu; Momosaki, Kyoko; Yamamoto, Shinji; Zhang, Fabi; Guo, Qixin; Noguchi, Hideyuki

2015-01-01

Highlights: • Ti substituted P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode was synthesized. • Structural and electrochemical properties of Na 2/3 Ni 1/4 Ti x Mn 3/4-x O 2 were studied. • Ti substituted cathodes exhibit enhanced cycleability and rate performance. • Ti substitution has impact on stabilizing the P2 structure during cycling. -- Abstract: Ti substituted P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode material with the composition of Na 2/3 Ni 1/4 Ti x Mn 3/4-x O 2 has been synthesized by solid state method. The influence of Ti substitution for Mn on the structure, morphology and electrochemical performances of P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 has been investigated. X-ray diffraction (XRD) results of Ti substituted sample show that they exhibit same diffraction patterns as those of pristine P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 . Progressive change in the lattice parameters of Ti substituted samples suggests that Mn was successfully substituted by Ti. In contrast to P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 which shows step-type voltage profiles, Ti substituted samples show sloping voltage profiles. Drastic capacity fade occurred for P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode, while Ti substituted cathodes still show high capacity retention over 92% after 25 cycles at the voltage range of 2.0-4.3 V. Even cycled at high upper cut-off voltage of 4.5 V, Ti=0.20 sample can deliver a reversible capacity of 140 mAhg −1 with the capacity retention over 92% after 25 cycles. Furthermore, Ti substituted cathodes exhibit enhanced rate capability over pristine P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode. Comparison of the Ex-situ XRD results of the cycled P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 and its substituted samples provides evidence that the improved electrochemical performance of Ti substituted cathodes would be attributed to the stabilization of the structure with Ti substitution

Facile Preparation of TiO2 Nanobranch/Nanoparticle Hybrid Architecture with Enhanced Light Harvesting Properties for Dye-Sensitized Solar Cells

Directory of Open Access Journals (Sweden)

Ju Seong Kim

2015-01-01

Full Text Available We report TiO2 nanobranches/nanoparticles (NBN hybrid architectures that can be synthesized by a facile solution phase method. The hybrid architecture simultaneously improves light harvesting and charge collection performances for a dye-sensitized solar cell. First, TiO2 nanorods with a trunk length of 2 μm were grown on a fluorine-doped tin oxide (FTO/glass substrate, and then nanobranches and nanoparticles were deposited on the nanorods’ trunks through a solution method using an aqueous TiCl3 solution at 80°C. The relative amount of nanobranches and nanoparticles can be controlled by multiplying the number of TiCl3 treatments to maximize the amount of surface area. We found that the resultant TiO2 NBN hybrid architecture greatly improves the amount of dye adsorption (five times compared to bare nanorods due to the enhanced surface area, while maintaining a fast charge collection, leading to a three times higher current density and thus tripling the maximum power conversion efficiency for a dye-sensitized solar cell.

微量TiC对Mo-Ti-Zr-TiC合金性能与显微组织的影响%Effect of Trace TiC on Property and Microstructure of Mo-Ti-Zr-TiC Alloy

Institute of Scientific and Technical Information of China (English)

钱昭; 范景莲; 成会朝; 田家敏

2012-01-01

采用粉末冶金方法制备Mo-Ti-Zr-TiC合金,研究微量TiC的添加对Mo-Ti-Zr-TiC合金的拉伸性能和显微组织的影响.结果表明,在Mo-Ti-Zr合金中添加微量TiC(0.1％～0.5％,质量分数)后,合金的相对密度和室温抗拉强度得到了提高,当TiC添加量为0.4％时,合金强度最高,较Mo-Ti-Zr合金提高了28.1％.微量TiC的添加,阻碍了合金烧结过程中的晶粒长大,合金晶粒尺寸随TiC添加量的增加而降低.添加的细小TiC粒子在高温烧结过程中或与坯体中的微量氧发生反应形成了由Mo、Ti、C及O 4种元素组成的(Mo,Ti)xOyCz细小复合第二相粒子,或发生团聚结成大颗粒,对合金起到净化晶界氧和弥散强化的作用,因而合金的性能相比Mo-Ti-Zr合金有了较明显的提高.%Mo-Ti-Zr-TiC alloy was prepared via powder metallurgy method. The effects of trace TiC additive on the mechanical properties and microstructure of TiC reinforced Mo-Ti-Zr-TiC alloy were studied. The results indicate that the relative density and the tensile strength at room temperature of Mo-Ti-Zr-TiC alloy is effectively enhanced by adding trace TiC (0.1wt%~0.5wt%). The tensile strength achieves the highest value when the content of TiC is 0.4wt%, which is 28.1% higher than that of Mo-Ti-Zr alloy. The adding of trace TiC can inhibit the grain growth during alloy sintering process, which leads to the decrease of grain sizes with the rise of TiC content. A part of the fine TiC particles react with trace oxygen in molybdenum matrix to form (Mo,Ti)xOyC2 compound second phase particles during high temperature sintering, while the other part are agglomerated into large particles, which play a role in grain boundaries purification and dispersion-strengthening.

Fabrication of TiO{sub 2} nanorod assembly grafted rGO (rGO@TiO{sub 2}-NR) hybridized flake-like photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Lv, Kangle, E-mail: lvkangle@mail.scuec.edu.cn [Department of Science and Environmental Studies, The Hong Kong Institute of Education, Taipo, N.T., Hong Kong (China); Key Laboratory of Catalysis and Materials Science of the State Ethnic Affairs Commission and Ministry of Education, College of Resources and Environmental Science, South-Central University for Nationalities, Wuhan 430074 (China); Fang, Shun; Si, Lingling; Xia, Yang [Key Laboratory of Catalysis and Materials Science of the State Ethnic Affairs Commission and Ministry of Education, College of Resources and Environmental Science, South-Central University for Nationalities, Wuhan 430074 (China); Ho, Wingkei, E-mail: keithho@ied.edu.hk [Department of Science and Environmental Studies, The Hong Kong Institute of Education, Taipo, N.T., Hong Kong (China); Li, Mei [Key Laboratory of Catalysis and Materials Science of the State Ethnic Affairs Commission and Ministry of Education, College of Resources and Environmental Science, South-Central University for Nationalities, Wuhan 430074 (China)

2017-01-01

Highlights: • TiO{sub 2} nanorod assembly grafted with GO hybrid was successfully fabricated. • TiO{sub 2} nanorods can reduce the aggregation of TiO{sub 2} nanoparticles on graphene. • This unique structure facilitates the injection of electron from TiO{sub 2} to graphene. - Abstract: To efficiently separate the photo-generated electron–hole pairs of TiO{sub 2} hybrid, anatase TiO{sub 2} nanorod assembly grafted reduced graphene oxides (rGO@TiO{sub 2}-NR) hybrid was successfully fabricated using potassium titanium oxalate (PTO) and graphene oxides (GO) as starting materials and diethylene glycol (DEG) as reductant. The effect of GO content on the structure and photocatalytic activity of rGO@TiO{sub 2}-NR composite was systematically studied. Results show that, in the absence of GO, only TiO{sub 2} microsphere assembly is obtained from TiO{sub 2} nanorods. The presence of GO results in the formation of a flake-like TiO{sub 2}-nanorod-assembled grafted rGO hybrid. The photocatalytic activity of rGO@TiO{sub 2}-NR composite increases first and then decreases with increase in the amount of GO from 0 wt.% to 10 wt.%. The hybridized S4 sample prepared with 4 wt.% GO possesses the highest photocatalytic activity with a constant rate of 0.039 min{sup −1} in the photocataytic degradation of Brilliant X-3B dye (X3B); this sample was enhanced more than three times when compared with pure TiO{sub 2} sample (0.012 min{sup −1}). The enhanced photocatalytic activity of the rGO@TiO{sub 2}-NR hybrid was attributed to the strong interaction between TiO{sub 2} nanorods and rGO. The unique hierarchical structure of 1D nanorod assembly TiO{sub 2}–rGO flakes facilitates the injection and transfer of photo-generated electrons from TiO{sub 2} to graphene, thus retarding the recombination of electron–hole pairs and enhancing the photocatalytic activity. The enlarged BET surface areas, not only increasing the number of active sites, but also facilitating the adsorption of

Light harvesting enhancement for dye-sensitized solar cells by novel anode containing cauliflower-like TiO{sub 2} spheres

Energy Technology Data Exchange (ETDEWEB)

Yang, Lei [Beijing National Laboratory for Molecular Science, Key Laboratory of Photochemistry, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100080 (China); Graduate University of the Chinese Academy of Sciences, Beijing 100049 (China); Lin, Yuan; Xiao, Xurui; Li, Xueping; Zhou, Xiaowen [Beijing National Laboratory for Molecular Science, Key Laboratory of Photochemistry, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100080 (China); Jia, Jianguang [Department of Chemistry, School of Science, Beijing University of Chemical Technology, Beijing 100029 (China)

2008-07-15

Cauliflower-like TiO{sub 2} rough spheres, which are about 200 nm large, have greatly enhanced light harvesting efficiency and energy conversion efficiency of dye-sensitized solar cells (DSC), due to their high light scattering effect and large BET surface area (80.7 m{sup 2} g{sup -1}) even after calcinations at 450 C for 30 min. The large size TiO{sub 2} rough and smooth spheres, produced at different initial temperatures by hydrolysis of Ti(OBu){sub 4} with P105 (EO{sub 37}PO{sub 56}EO{sub 37}) or F68 (EO{sub 78}PO{sub 30}EO{sub 78}) tri-block copolymer as structural agents, have nearly the same diameter of {proportional_to}275 nm and strong light scattering effects in the wavelength of 400-750 nm. However, rough spheres have even higher light scattering effect and larger BET surface area than smooth spheres for the roughness of the surface. By adding 25 wt.% large TiO{sub 2} spheres into the over-layer of TiO{sub 2} film composed of {proportional_to}20 nm TiO{sub 2} particles as light scattering centers, the energy conversion efficiency of the film containing rough spheres reaches 7.36%, much larger than that of smooth spheres (6.25%). From another point of view, the TiO{sub 2} rough spheres may have the satisfying ability in other fields of application such as photo-catalysis, drug carriers and so on. (author)

Hierarchical TiO{sub 2} submicron-sized spheres for enhanced power conversion efficiency in dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Wang, Hao [Hubei Collaborative Innovation Centre for Advanced Organic Chemical Materials and Ministry of Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei University, Wuhan 430062 (China); State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Guo, Zhiguang, E-mail: zguo@licp.cas.cn [Hubei Collaborative Innovation Centre for Advanced Organic Chemical Materials and Ministry of Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei University, Wuhan 430062 (China); State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)

2015-10-15

Hierarchical TiO{sub 2} submicron-sized sphere scattering layer, with relatively large surface area and effective light scattering, shows enhanced power conversion efficiency in dye-sensitized solar cells. - Highlights: • Hierarchical TiO{sub 2} submicron-sized spheres (TiO{sub 2} HSSs) with diameters of 400–600 nm were synthesized. • The HSSs composed of nanoparticles of ∼14 nm have a relatively large surface area of ∼35 m{sup 2}/g. • DSC exhibited the highest cell efficiency (6.23%) compared with ones with pure P25 (5.50%) or HSS (2.00%) photoanodes. - Abstract: Hierarchical TiO{sub 2} submicron-sized spheres (TiO{sub 2} HSSs) with diameters of 400–600 nm were synthesized by a facile one-step solvothermal method in ethanol solvent. The HSSs composed of nanoparticles of ∼14 nm have a relatively large surface area of ∼35 m{sup 2}/g. When applied as the scattering overlayer in dye-sensitized solar cells (DSCs), such TiO{sub 2} HSSs effectively improved light harvesting and led to the increase of photocurrent in DSCs. Furthermore, bilayer-structured photoanode also provided fast electron transportation and long electron lifetime as confirmed by electrochemical impedance spectra. As a result, DSC based on P25 nanoparticle underlayer and HSS-2 overlayer exhibited the highest cell efficiency (6.23%) compared with ones with pure P25 (5.50%) or HSS-2 (2.00%) photoanodes.

Microstructural evolution and mechanical properties of Ti3SiC2-TiC composites

International Nuclear Information System (INIS)

Tian, WuBian; Sun, ZhengMing; Hashimoto, Hitoshi; Du, YuLei

2010-01-01

Ti 3 SiC 2 -TiC composites were fabricated by pulse discharge sintering technique using three different sets of powder mixtures, i.e. Ti/Si/TiC (TC30), Ti/Si/C/TiC (SI30) and Ti/Si/C (TSC30). Based on X-ray diffraction (XRD) analysis and microstructural observations, starting powder reactants were found to have little effect on phase content but strong influence on the microstructure in terms of phase distribution. The phase distribution mainly relies on the heat released from reaction and the liquid phase content formed during sintering. The mechanical properties of the fabricated dense samples demonstrate that more homogeneous phase distribution, available by choosing the starting reactants of SI30, results in higher flexural strength, whereas the Vickers hardness is almost independent of the microstructure. The enhanced flexural strength in sample SI30 sintered at 1400 o C is mainly attributed to the homogeneous TiC distribution in the microstructure.

Enhanced dielectric and ferroelectric characteristics in Ca-modified BaTiO3 ceramics

Directory of Open Access Journals (Sweden)

Xiao Na Zhu

2013-08-01

Full Text Available Synergic modification of BaTiO3 ceramics was investigated by Ca-substitution, and the superior dielectric and ferroelectric properties were determined together with the structure evolution. X-ray diffraction (XRD analysis demonstrated a large solubility limit above x = 0.25 in Ba1−xCaxTiO3 solid solution where the fine grain structure was observed with increasing x. Room temperature dielectric constant as high as 1655 was achieved in the present ceramics together with the significantly reduced dielectric loss of 0.013 (x = 0.20 at 100 kHz, where the Curie temperature kept almost a constant while other two transition temperatures decreased continuously with increasing x. More importantly, the remanent polarization Pr and dielectric strength Eb were significantly enhanced by Ca-substitution, and the best Pr (11.34 μC/cm2 and the highest dielectric strength Eb (75 kV/cm were acquired at x = 0.25. The present ceramics should be very desirable for the applications such as high density energy storage devices.

Uniformly dispersed CdS nanoparticles sensitized TiO{sub 2} nanotube arrays with enhanced visible-light photocatalytic activity and stability

Energy Technology Data Exchange (ETDEWEB)

Liu, Lingjuan [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Anhui Provincial Key Laboratory of Advanced Functional Materials and Devices, Hefei 230009 (China); Lv, Jun, E-mail: lvjun117@126.com [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Anhui Provincial Key Laboratory of Advanced Functional Materials and Devices, Hefei 230009 (China); Xu, Guangqing; Wang, Yan; Xie, Kui [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Anhui Provincial Key Laboratory of Advanced Functional Materials and Devices, Hefei 230009 (China); Chen, Zhong [School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue 639798 (Singapore); Wu, Yucheng, E-mail: ycwu@hfut.edu.cn [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Anhui Provincial Key Laboratory of Advanced Functional Materials and Devices, Hefei 230009 (China)

2013-12-15

In this study, TiO{sub 2} nanotube arrays (TiO{sub 2}-NTs) with various intertube spaces were fabricated in the electrolyte with different water contents and the CdS nanoparticles (CdS NPs) were further deposited onto the TiO{sub 2}-NTs as a sensitizer via a sequential chemical bath deposition (S-CBD) method. The FE-SEM, TEM, XRD and XPS results demonstrated that the CdS NPs were uniformly deposited onto the surface of TiO{sub 2}-NTs. It was found that higher water content in electrolyte was in favor of large intertube space and pore size and the uniform deposition of CdS NPs. The photocatalytic degradation of methyl orange was tested with the as-prepared CdS/TiO{sub 2}-NTs under visible light (λ>400 nm). It was found that the photodegradation rate reached as high as 96.7% under visible irradiation for 180 min. In addition, a reasonable degradation rate of 75.8% was achieved even after 5 cycles, suggesting a good photocatalytic stability of the as-prepared CdS/TiO{sub 2}-NTs. - Graphical abstract: The whole sheet of CdS NPs sensitized TiO{sub 2}-NTs with the Ti subtract was used for degradation of methyl orange under visible light (λ>400 nm) on a XPA-7 photochemical reactor. - Highlights: • Intertube space, pore size were controlled by changing water content in electrolyte. • CdS nanoparticles were uniformly deposited onto the surface of TiO{sub 2} nanotubes. • The catalyst with Ti substrate used as a whole was very convenient for recycling. • Visible-light photocatalytic activity and stability were highly enhanced.

Visible Light Photoelectrochemical Properties of N-Doped TiO2 Nanorod Arrays from TiN

Directory of Open Access Journals (Sweden)

Zheng Xie

2013-01-01

Full Text Available N-doped TiO2 nanorod arrays (NRAs were prepared by annealing the TiN nanorod arrays (NRAs which were deposited by using oblique angle deposition (OAD technique. The TiN NRAs were annealed at 330°C for different times (5, 15, 30, 60, and 120 min. The band gaps of annealed TiN NRAs (i.e., N-doped TiO2 NRAs show a significant variance with annealing time, and can be controlled readily by varying annealing time. All of the N-doped TiO2 NRAs exhibit an enhancement in photocurrent intensity in visible light compared with that of pure TiO2 and TiN, and the one annealed for 15 min shows the maximum photocurrent intensity owning to the optimal N dopant concentration. The results show that the N-doped TiO2 NRAs, of which the band gap can be tuned easily, are a very promising material for application in photocatalysis.

Enhancing mathematics teachers' quality through Lesson Study.

Science.gov (United States)

Lomibao, Laila S

2016-01-01

The efficiency and effectivity of the learning experience is dependent on the teacher quality, thus, enhancing teacher's quality is vital in improving the students learning outcome. Since, the usual top-down one-shot cascading model practice for teachers' professional development in Philippines has been observed to have much information dilution, and the Southeast Asian Ministers of Education Organization demanded the need to develop mathematics teachers' quality standards through the Southeast Asia Regional Standards for Mathematics Teachers (SEARS-MT), thus, an intensive, ongoing professional development model should be provided to teachers. This study was undertaken to determine the impact of Lesson Study on Bulua National High School mathematics teachers' quality level in terms of SEARS-MT dimensions. A mixed method of quantitative-qualitative research design was employed. Results of the analysis revealed that Lesson Study effectively enhanced mathematics teachers' quality and promoted teachers professional development. Teachers positively perceived Lesson Study to be beneficial for them to become a better mathematics teacher.

Laser Nitriding of the Newly Developed Ti-20Nb-13Zr at.% Biomaterial Alloy to Enhance Its Mechanical and Corrosion Properties in Simulated Body Fluid

Science.gov (United States)

Hussein, M. A.; Kumar, A. Madhan; Yilbas, Bekir S.; Al-Aqeeli, N.

2017-11-01

Despite the widespread application of Ti alloy in the biomedical field, surface treatments are typically applied to improve its resistance to corrosion and wear. A newly developed biomedical Ti-20Nb-13Zr at.% alloy (TNZ) was laser-treated in nitrogen environment to improve its surface characteristics with corrosion protection performance. Surface modification of the alloy by laser was performed through a Nd:YAG laser. The structural and surface morphological alterations in the laser nitrided layer were investigated by XRD and a FE-SEM. The mechanical properties have been evaluated using nanoindentation for laser nitride and as-received samples. The corrosion protection behavior was estimated using electrochemical corrosion analysis in a physiological medium (SBF). The obtained results revealed the production of a dense and compact film of TiN fine grains (micro-/nanosize) with 9.1 µm below the surface. The mechanical assessment results indicated an improvement in the modulus of elasticity, hardness, and resistance of the formed TiN layer to plastic deformation. The electrochemical analysis exhibited that the surface protection performance of the laser nitrided TNZ substrates in the SBF could be considerably enhanced compared to that of the as-received alloy due to the presence of fine grains in the TiN layer resulting from laser nitriding. Furthermore, the untreated and treated Ti-20Nb-13Zr alloy exhibited higher corrosion resistance than the CpTi and Ti6Al4V commercial alloys. The improvements in the surface hardness and corrosion properties of Ti alloy in a simulated body obtained using laser nitriding make this approach a suitable candidate for enhancing the properties of biomaterials.

Enhanced Bonding of Silver Nanoparticles on Oxidized TiO2(110)

DEFF Research Database (Denmark)

Hansen, Jonas Ørbæk; Salazar, Estephania Lira; Galliker, Patrick

2010-01-01

The nucleation and growth of silver nanoclusters on TiO2(110) surfaces with on-top O adatoms (oxidized TiO2), surface O vacancies and H adatoms (reduced TiO2) have been studied. From the interplay of scanning tunneling microscopy/photoelectron spectroscopy experiments and density functional theor...

Highly enhanced photocatalytic degradation of methylene blue over the indirect all-solid-state Z-scheme g-C{sub 3}N{sub 4}-RGO-TiO{sub 2} nanoheterojunctions

Energy Technology Data Exchange (ETDEWEB)

Wu, Fangjun [College of Materials and Energy, South China Agricultural University, Guangzhou 510642 (China); Li, Xin [College of Materials and Energy, South China Agricultural University, Guangzhou 510642 (China); Institute of New Energy and New Materials, Key Laboratory of Energy Plants Resource and Utilization, Ministry of Agriculture, South China Agricultural University, Guangzhou 510642 (China); College of Forestry and Landscape Architecture, South China Agricultural University, Guangzhou 510642 (China); Liu, Wei, E-mail: wlscau@163.com [College of Materials and Energy, South China Agricultural University, Guangzhou 510642 (China); Zhang, Shuting [College of Materials and Energy, South China Agricultural University, Guangzhou 510642 (China)

2017-05-31

Highlights: • The indirect Z-scheme g-C{sub 3}N{sub 4}-RGO-TiO{sub 2} photocatalysts were successfully fabricated. • A 3.2-fold activity enhancement was achieved by inserting RGO into g-C{sub 3}N{sub 4}- TiO{sub 2}. • The indirect Z-scheme mechanism was verified by PL spectra and radical trapping. • The multi-functional roles of RGO in enhancing photodegradation were revealed. - Abstract: In the present research work, the ternary indirect all-solid-state Z-scheme nanoheterojunctions, graphitic-C{sub 3}N{sub 4}/reduced graphene oxide/anatase TiO{sub 2} (g-C{sub 3}N{sub 4}-RGO-TiO{sub 2}) with highly enhanced photocatalytic performance were successfully prepared via a simple liquid-precipitation strategy. The photocatalytic activities of indirect all-solid-state Z-scheme g-C{sub 3}N{sub 4}-RGO-TiO{sub 2} nanoheterojunctions were evaluated by the degradation of methylene blue (MB). The results showed that the introduction of RGO as an interfacial mediator into direct Z-scheme g-C{sub 3}N{sub 4}-TiO{sub 2} nanocomposites can remarkably enhance their photocatalytic activities. The as-obtained indirect all-solid-state Z-scheme g-C{sub 3}N{sub 4}-RGO-TiO{sub 2} nanoheterojunctions, with the optimal loading amount of 10 wt% RGO, exhibited the highest rate towards the photocatalytic degradation of MB under simulated solar light irradiation. The degradation kinetics of MB can be described by the apparent first-order kinetics model. The highest degradation rate constant of 0.0137 min{sup −1} is about 4.7 and 3.2 times greater than those of the pure g-C{sub 3}N{sub 4} (0.0029 min{sup −1}) and direct Z-scheme g-C{sub 3}N{sub 4}-TiO{sub 2} (0.0043 min{sup −1}), respectively. An indirect all-solid-state Z-scheme charge-separation mechanism was proposed based on the photoluminescence spectra and the trapping experiment procedure of the photo-generated active species. It was believed that the indirect all-solid-state Z-scheme charge separation mechanism in g-C{sub 3}N

Synthesis of activated charcoal supported Bi-doped TiO{sub 2} nanocomposite under solar light irradiation for enhanced photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Chandraboss, V.L.; Kamalakkannan, J.; Senthilvelan, S., E-mail: dr_senthilvel@yahoo.co.in

2016-11-30

Highlights: • Particle size and band gap of TiO{sub 2} is decreased upon Bi doping. • Methylene blue is successfully degraded over Bi/TiO{sub 2} and AC-Bi/TiO{sub 2}. • AC-Bi/TiO{sub 2} is more active photocatalyst than TiO{sub 2} and Bi/TiO{sub 2}. • AC-Bi/TiO{sub 2} led to a maximum extension of the spectral wavelength. • AC-Bi/TiO{sub 2} with enhanced photocatalytic activity produced much more reactive ·OH. - Abstract: In this study, activated charcoal (AC) supported bismuth (Bi)-doped Titanium dioxide (TiO{sub 2}) nanocomposite was synthesized by precipitation method. The photocatalytic activity of AC-Bi/TiO{sub 2} was investigated for the degradation of methylene blue (MB) in aqueous solution under solar light irradiation. The incorporation of Bi{sup 3+} into the TiO{sub 2} lattice shifts the absorbance of TiO{sub 2} to the visible region then the addition of high adsorption capacity activated charcoal to improve the efficiency of TiO{sub 2}. AC-Bi/TiO{sub 2} is found to be more efficient than Bi/TiO{sub 2} and undoped TiO{sub 2} for the degradation of MB under solar light irradiation. Surface morphology and bulk composition of the composite was obtained using high resolution-scanning electron microscopy with energy dispersive X-ray analysis. The crystal structure evolution and elemental composition were analyzed by combining Fourier transform-Raman spectroscopy, X-ray diffraction and X-ray photoelectron spectroscopy. The ultraviolet-visible (UV–vis) absorption spectra show that the absorption edge for the composite with Bi{sup 3+} has red shift as compared with that of undoped TiO{sub 2}. UV–vis diffuse reflectance spectra demonstrated a decrease in the direct band gap of AC-Bi/TiO{sub 2}. BET surface area, pore radius and pore volume of the materials were calculated by applying the BET equation to the sorption isotherms. The production of hydroxyl radicals (·OH) on the surface of solar light irradiated materialswere detected by

Mechanism of Surface-Enhanced Raman Scattering Based on 3D Graphene-TiO2 Nanocomposites and Application to Real-Time Monitoring of Telomerase Activity in Differentiation of Stem Cells.

Science.gov (United States)

Zheng, Tingting; Feng, Enduo; Wang, Zhiqiang; Gong, Xueqing; Tian, Yang

2017-10-25

With a burst development of new nanomaterials for plasmon-free surface-enhanced Raman scattering (SERS), the understanding of chemical mechanism (CM) and further applications have become more and more attractive. Herein, a novel SERS platform was specially designed through electrochemical deposition of graphene onto TiO 2 nanoarrays (EG-TiO 2 ). The developed EG-TiO 2 nanocomposite SERS platform possessed remarkable Raman activity using copper phthalocyanine (CuPc) as a probe molecule. X-ray photoelectron spectroscopy measurement revealed that the chemical bond Ti-O-C was formed at the interface between graphene and TiO 2 in EG-TiO 2 nanocomposites. Both experimental and theoretical results demonstrated that the obvious Raman enhancement was attributed to TiO 2 -induced Fermi level shift of graphene, resulting in effective charge transfer between EG-TiO 2 nanocomposites and molecules. Taking advantage of a marked Raman response of the CuPc molecule on the EG-TiO 2 nanocomposite surface as well as specific recognition of CuPc toward multiple telomeric G-quadruplex, EG-TiO 2 nanocomposites were tactfully employed as the SERS substrate for selective and ultrasensitive determination of telomerase activity, with a low detection limit down to 2.07 × 10 -16 IU. Interestingly, the self-cleaning characteristic of EG-TiO 2 nanocomposites under visible light irradiation successfully provided a recycling ability for this plasmon-free EG-TiO 2 substrate. The present SERS biosensor with high analytical performance, such as high selectivity and sensitivity, has been further explored to determine telomerase activity in stem cells as well as to count the cell numbers. More importantly, using this useful tool, it was discovered that telomerase activity plays an important role in the proliferation and differentiation from human mesenchymal stem cells to neural stem cells. This work has not only established an approach for gaining fundamental insights into the chemical mechanism (CM

Assessing Participation in Secondary Education Quality Enhancement

African Journals Online (AJOL)

Assessing Participation in Secondary Education Quality Enhancement: Teachers, Parents and Communities in Cross River State. ... ailing economy, low moral values and philosophy of the end justifies the means were reasons for low parents and communities involvement in secondary education-quality improvement.

A Simple Method for the Preparation of TiO2 /Ag-AgCl@Polypyrrole Composite and Its Enhanced Visible-Light Photocatalytic Activity.

Science.gov (United States)

Yao, Tongjie; Shi, Lei; Wang, Hao; Wang, Fangxiao; Wu, Jie; Zhang, Xiao; Sun, Jianmin; Cui, Tieyu

2016-01-01

A novel and facile method was developed to prepare a visible-light driven TiO2 /Ag-AgCl@polypyrrole (PPy) photocatalyst with Ag-AgCl nanoparticles supported on TiO2 nanofibers and covered by a thin PPy shell. During the synthesis, the PPy shell and Ag-AgCl nanoparticles were prepared simultaneously onto TiO2 nanofibers, which simplified the preparation procedure. In addition, because Ag-AgCl aggregates were fabricated via partly etching the Ag nanoparticles, their size was well controlled at the nanoscale, which was beneficial for improvement of the contact surface area. Compared with reference photocatalysts, the TiO2 /Ag-AgCl@PPy composite exhibited an enhanced photodegradation activity towards rhodamine B under visible-light irradiation. The superior photocatalytic property originated from synergistic effects between TiO2 nanofibers, Ag-AgCl nanoparticles and the PPy shell. Furthermore, the TiO2 /Ag-AgCl@PPy composite could be easily separated and recycled without obvious reduction in activity. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Enhancement of photocatalytic degradation of dimethyl phthalate with nano-TiO{sub 2} immobilized onto hydrophobic layered double hydroxides: A mechanism study

Energy Technology Data Exchange (ETDEWEB)

Huang, Zhujian [College of Environmental Science and Engineering, South China University of Technology, Guangzhou 510006 (China); The Key Lab of Pollution Control and Ecosystem Restoration in Industry Clusters, Ministry of Education, Guangzhou 510006 (China); Wu, Pingxiao, E-mail: pppxwu@scut.edu.cn [College of Environmental Science and Engineering, South China University of Technology, Guangzhou 510006 (China); The Key Lab of Pollution Control and Ecosystem Restoration in Industry Clusters, Ministry of Education, Guangzhou 510006 (China); The Key Laboratory of Environmental Protection and Eco-Remediation of Guangdong Regular Higher Education Institutions (China); Lu, Yonghong; Wang, Xiaorong; Zhu, Nengwu [College of Environmental Science and Engineering, South China University of Technology, Guangzhou 510006 (China); The Key Lab of Pollution Control and Ecosystem Restoration in Industry Clusters, Ministry of Education, Guangzhou 510006 (China); Dang, Zhi [College of Environmental Science and Engineering, South China University of Technology, Guangzhou 510006 (China); The Key Lab of Pollution Control and Ecosystem Restoration in Industry Clusters, Ministry of Education, Guangzhou 510006 (China); The Key Laboratory of Environmental Protection and Eco-Remediation of Guangdong Regular Higher Education Institutions (China)

2013-02-15

Highlights: ► The reconstructed organic LDHs are consisted of the interconnecting nano-flakes. ► It is confirmed that organic LDHs/TiO{sub 2} composites are combined together by chemical bonds. ► The organic LDHs with flaky structure effectively enrich DPM onto the composite. ► The abundant external hydroxyl groups of organic LDHs promote the production of ·OH. ► TiO{sub 2} immobilized onto organic LDHs greatly enhances the photodegradation of DMP. -- Abstract: The organic layered double hydroxides (LHDs)/TiO{sub 2} composites with various mass ratios were prepared by the reconstruction of mixed metal oxides to photodegrade dimethyl phthalate (DMP). The physicochemical properties of the obtained products were analyzed by X-ray diffraction (XRD) spectra, X-ray photoelectron spectra (XPS), UV–vis diffuse reflectance spectroscope and scanning electron microscope (SEM). The results showed that the TiO{sub 2} particles and the organic LDHs were combined together through chemical bonds, and TiO{sub 2} particles were well distributed on the surface of the interconnecting organic LDHs nano-flakes. According to the experimental results of adsorptive and photodegradation of DMP, the organic LDHs with flaky structure could effectively adsorb the DMP molecules and the adsorption isotherm by the composites modeled well with the Langmuir equation. The enrichment of DMP onto the composites and the external hydroxyl groups of the composites produce a synergistic effect leading to greatly enhance the rate of DMP photocatalytic degradation by the obtained composites.