WorldWideScience

Sample records for thz antenna structures

  1. Spiral Antenna-Coupled Microbridge Structures for THz Application.

    Science.gov (United States)

    Gou, Jun; Zhang, Tian; Wang, Jun; Jiang, Yadong

    2017-12-01

    Bolometer sensor is a good candidate for THz imaging due to its compact system, low cost, and wideband operation. Based on infrared microbolometer structures, two kinds of antenna-coupled microbridge structures are proposed with different spiral antennas: spiral antenna on support layer and spiral antenna with extended legs. Aiming at applications in detection and imaging, simulations are carried out mainly for optimized absorption at 2.52 THz, which is the radiation frequency of far-infrared CO 2 lasers. The effects of rotation angle, line width, and spacing of the spiral antenna on THz wave absorption of microbridge structures are discussed. Spiral antenna, with extended legs, is a good solution for high absorption rate at low absorption frequency and can be used as electrode lead simultaneously for simplified manufacturing process. A spiral antenna-coupled microbridge structure with an absorption rate of more than 75% at 2.52 THz is achieved by optimizing the structure parameters. This research demonstrates the use of different spiral antennas for enhanced and tunable THz absorption of microbridge structures and provides an effective way to fabricate THz microbolometer detectors with great potential in the application of real-time THz imaging.

  2. Frequency Modulation and Absorption Improvement of THz Micro-bolometer with Micro-bridge Structure by Spiral-Type Antennas

    Science.gov (United States)

    Gou, Jun; Niu, Qingchen; Liang, Kai; Wang, Jun; Jiang, Yadong

    2018-03-01

    Antenna-coupled micro-bridge structure is proven to be a good solution to extend infrared micro-bolometer technology for THz application. Spiral-type antennas are proposed in 25 μm × 25 μm micro-bridge structure with a single separate linear antenna, two separate linear antennas, or two connected linear antennas on the bridge legs, in addition to traditional spiral-type antenna on the support layer. The effects of structural parameters of each antenna on THz absorption of micro-bridge structure are discussed for optimized absorption of 2.52 THz wave radiated by far infrared CO2 lasers. The design of spiral-type antenna with two separate linear antennas for wide absorption peak and spiral-type antenna with two connected linear antennas for relatively stable absorption are good candidates for high absorption at low absorption frequency with a rotation angle of 360* n ( n = 1.6). Spiral-type antenna with extended legs also provides a highly integrated micro-bridge structure with fast response and a highly compatible, process-simplified way to realize the structure. This research demonstrates the design of several spiral-type antenna-coupled micro-bridge structures and provides preferred schemes for potential device applications in room temperature sensing and real-time imaging.

  3. Frequency Modulation and Absorption Improvement of THz Micro-bolometer with Micro-bridge Structure by Spiral-Type Antennas.

    Science.gov (United States)

    Gou, Jun; Niu, Qingchen; Liang, Kai; Wang, Jun; Jiang, Yadong

    2018-03-05

    Antenna-coupled micro-bridge structure is proven to be a good solution to extend infrared micro-bolometer technology for THz application. Spiral-type antennas are proposed in 25 μm × 25 μm micro-bridge structure with a single separate linear antenna, two separate linear antennas, or two connected linear antennas on the bridge legs, in addition to traditional spiral-type antenna on the support layer. The effects of structural parameters of each antenna on THz absorption of micro-bridge structure are discussed for optimized absorption of 2.52 THz wave radiated by far infrared CO 2 lasers. The design of spiral-type antenna with two separate linear antennas for wide absorption peak and spiral-type antenna with two connected linear antennas for relatively stable absorption are good candidates for high absorption at low absorption frequency with a rotation angle of 360*n (n = 1.6). Spiral-type antenna with extended legs also provides a highly integrated micro-bridge structure with fast response and a highly compatible, process-simplified way to realize the structure. This research demonstrates the design of several spiral-type antenna-coupled micro-bridge structures and provides preferred schemes for potential device applications in room temperature sensing and real-time imaging.

  4. Improving the efficiency and directivity of THz photoconductive antennas by using a defective photonic crystal substrate

    Science.gov (United States)

    Rahmati, Ehsan; Ahmadi-Boroujeni, Mehdi

    2018-04-01

    One of the shortcomings of photoconductive (PC) antennas in terahertz (THz) generation is low effective radiated power in the desirable direction. In this paper, we propose a defective photonic crystal (DPC) substrate consisting of a customized 2D array of air holes drilled into a solid substrate in order to improve the radiation characteristics of THz PC antennas. The effect of the proposed structure on the performance of a conventional THz PC antenna has been examined from several aspects including radiation efficiency, directivity, and field distribution. By comparing the radiation performance of the THz antenna on the proposed DPC substrate to that of the conventional solid substrate, it is shown that the proposed technique can significantly improve the efficiency and directivity of the THz PC antenna over a wide frequency range. It is achieved by reducing the amount of power coupled to the substrate surface waves and limiting the radiation in undesirable directions. In addition, it is found that the sensitivity of directivity to the substrate thickness is considerably decreased and the adverse Fabry-Perot effects of the thick substrate are reduced by the application of the proposed DPC substrate.

  5. Tunable graphene antennas for selective enhancement of THz-emission

    KAUST Repository

    Filter, Robert

    2013-01-01

    In this paper, we will introduce THz graphene antennas that strongly enhance the emission rate of quantum systems at specific frequencies. The tunability of these antennas can be used to selectively enhance individual spectral features. We will show as an example that any weak transition in the spectrum of coronene can become the dominant contribution. This selective and tunable enhancement establishes a new class of graphene-based THz devices, which will find applications in sensors, novel light sources, spectroscopy, and quantum communication devices. © 2013 Optical Society of America.

  6. Sapphire decelerating capillary channel integrated with antenna at frequency 0.675 THz

    Science.gov (United States)

    Ashanin, I. A.; Polozov, S. M.

    2016-07-01

    In recent years, there has been an increasing interest in THz-radiation for application in medicine (THz tomographs), in pharmaceutics (composition analysis for medicines), in introscopy of large-scale objects (ships, trains, containers) and others. THz-radiation can be generated by relativistic electron bunches passing through the Cherenkov decelerating capillary channel (circular waveguide with dielectric filling) with horn extraction. Relativistic electron beams having ∼100 µm in diameter and pulse durations of 1 ps or less (as in photoinjectors) are capable of producing substantial power of THz-radiation. High-peak power coherent Cherenkov radiation can be produced by a properly modulated high-brightness electron beam or by a single, high-density bunch having sub-wavelength dimension. The aperture of a Cherenkov decelerating structure should be comparable with the mm or sub-mm wavelength (0.1-3 mm). Different dielectric materials for the internal surface coating of the capillary channel of mm-sub-mm cross-section can be used. As is known, a frequency of 0.675 THz corresponds to the atmospheric window with high transparency. This report presents the results of electrodynamics study of the metallized sapphire decelerating Cherenkov capillary. A horn antenna attached to the metallized sapphire capillary channel at the 0.675 THz resonant frequency will be considered.

  7. 28.3THz bowtie antenna integrated rectifier for infrared energy harvesting

    KAUST Repository

    Gadalla, Mena N.

    2014-10-01

    The design, fabrication and characterization of an asymmetric 28.3 THz antenna integrated rectifier (rectenna) using Au/Al2O3/Pt is presented. The rectenna design comprises a sharp tip bowtie antenna and a tunneling Metal-insulator-Metal (MIM) diode. The design benefits from the geometric field enhancement around the nano tips of the bowtie antenna. Simultaneous optimization of the antenna\\'s length and flare angle resulted in a relative intensity enhancement of 104 for a 10 nm gap. In order to benefit from the field enhancement, the THz diode is realized through the overlap of the bowtie sharp tips exactly at the hot spot. Dissimilar electrodes are used to allow THz signals rectification at zero bias, which is critical for energy harvesting applications. The rectenna exhibits a zero bias responsivity of 10 A/W. © 2014 European Microwave Association.

  8. Design and Simulation of an Antenna-Coupled Microbolometer at 30 THz

    Directory of Open Access Journals (Sweden)

    Angel Colin

    2017-01-01

    Full Text Available We propose a model of antenna-coupled microbolometer to be included in an array for receiving and detecting long wave infrared (LWIR electromagnetic radiation. The antenna is joined to microstrip bandpass filters thus forming a single metal structure to define the operation frequency band. The antenna and microstrip filters are modeled in aluminum thin film. The microbolometer is modeled with superconducting niobium, all together on a silicon nitride membrane. The squared pixel structure is designed on a support frame of 20 μm in size. Simulation results for this antenna exhibit a frequency range of operation from 27 to 35 THz and is configured for two arrays, one of 10×10 and the other one of 50×50 elements. The device has been simulated by means of the commercial electromagnetic software (HFSS, which is based on the finite elements method. The predicted values for the figures of merit of this microbolometer are as follows: τ=5.8 ns, Rv=5.3×103 V/W, and D⁎ = 2.07×1010 cmHz/W, respectively.

  9. Nano-Antenna For Terahertz (THz) Medical Imaging Applications

    Data.gov (United States)

    National Aeronautics and Space Administration — As a result of technological breakthroughs, research and applications in the Terahertz (THz) radiation system are experiencing explosive growth. The non-ionizing and...

  10. Surface enhancement of THz wave by coupling a subwavelength LiNbO3slab waveguide with a composite antenna structure.

    Science.gov (United States)

    Zhang, Qi; Qi, Jiwei; Wu, Qiang; Lu, Yao; Zhao, Wenjuan; Wang, Ride; Pan, Chongpei; Wang, Shibiao; Xu, Jingjun

    2017-12-14

    Highly intense terahertz electromagnetic field and efficiently surface localized terahertz field in subwavelength volumes are of vital importance for terahertz photonics integration, also will greatly accelerate the development for integrated applications in biochemical sensing, imaging, terahertz spectroscopy, enhancement of nonlinear effects and even quantum research. In this paper, we achieved large terahertz field enhancement and surface field localization through depositing a pair of Au composite antennas on a LiNbO 3 subwavelength slab waveguide, which can serve as an excellent on-chip platform for terahertz research and application. The antennas consist of two opposing tip-to-tip triangles separated by a gap, and each triangle combines with a strip antenna. Time-resolved imaging and finite-difference time-domain method were used to resolve the characteristics of the designed antennas experimentally and simulatively. Through these methods, we demonstrated outstanding abilities of the platform: leading to a large electric field enhancement, concentrating almost full terahertz energy on the waveguide's surface when they are resonant with the terahertz waves and tunable resonant frequency. These abilities make the subwavelength waveguide coupling with the composite antennas be able to sever as a good integrated device to identify terahertz-sensitive small objects, or an excellent platform to terahertz spectroscopy and quantum research.

  11. Multilayered Polymeric Photonic Structure for THz applications

    Science.gov (United States)

    Xia, Chen; Kosnosky, Louis; Shan, Jie; Lott, Joseph; Mackey, Matthew; Pethe, Vishwas; Baer, Eric; Hiltner, Anne; Weder, Christoph

    2008-03-01

    Photonic crystal have been widely studied in the visible, and recently become of interest in the THz regime of the electromagnetic spectrum. We have developed a rapid, easy and cost effective method for the preparation of polymeric materials with high refractive indices (RI) for the terahertz (THz) frequencies through extrusion of polymer and nanoparticles of inorganic materials. Using this method, we have fabricated a one-dimensional photonic crystal of polymer/polymer ferroelectric nanoparticles composite with a nearly complete stop band in the THz regime. The result will also be compared to a transfer-matrix calculation

  12. Three techniques for the fabrication of high precision, mm-sized metal components based on two-photon lithography, applied for manufacturing horn antennas for THz transceivers

    Science.gov (United States)

    Standaert, Alexander; Brancato, Luigi; Lips, Bram; Ceyssens, Frederik; Puers, Robert; Reynaert, Patrick

    2018-03-01

    This paper proposes a novel packaging solution which integrates micro-machined 3D horn antennas with millimeter-wave and THz tranceivers. This packaging solution is shown to be a valid competitor to existing technologies like metallic split-block waveguides and low temperature cofired ceramics. Three different fabrication methods based on two-photon lithography are presented to form the horn antennas. The first uses two-photon lithography to form the bulk of the antenna. This structure is then metalised through physical vapor deposition (PVD) and copper plating. The second fabrication method makes use of a soft polydimethylsiloxane (PDMS) mold to easily replicate structures and the third method forms the horn antenna through electroforming. A prototype is accurately positioned on top of a 400 GHz 28 nm CMOS transmitter and glued in place with epoxy, thus providing a fully packaged solution. Measurement results show a 12 dB increase in the antenna gain when using the packaged solution. The fabrication processes are not limited to horn antennas alone and can be used to form a wide range of mm-sized metal components.

  13. Double Structure Broadband Leaky Wave Antenna

    NARCIS (Netherlands)

    Neto, A.; Dijk, R. van; Filippo, M.

    2011-01-01

    A leaky wave antenna contains a first and a second leaky wave antenna structure back to back against each other. Each antenna structure comprises a dielectric body and an elongated wave carrying structure, such as a slot in a conductive ground plane. In each leaky wave antenna structure the body and

  14. 47 CFR 22.365 - Antenna structures; air navigation safety.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Antenna structures; air navigation safety. 22... Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become a hazard to air navigation. In general, antenna structure owners are...

  15. Structurally Integrated Antenna Concepts for HALE UAVs

    Science.gov (United States)

    Cravey, Robin L.; Vedeler, Erik; Goins, Larry; Young, W. Robert; Lawrence, Roland W.

    2006-01-01

    This technical memorandum describes work done in support of the Multifunctional Structures and Materials Team under the Vehicle Systems Program's ITAS (Integrated Tailored Aero Structures) Project during FY 2005. The Electromagnetics and Sensors Branch (ESB) developed three ultra lightweight antenna concepts compatible with HALE UAVs (High Altitude Long Endurance Unmanned Aerial Vehicles). ESB also developed antenna elements that minimize the interaction between elements and the vehicle to minimize the impact of wing flexure on the EM (electromagnetic) performance of the integrated array. In addition, computer models were developed to perform phase correction for antenna arrays whose elements are moving relative to each other due to wing deformations expected in HALE vehicle concepts. Development of lightweight, conformal or structurally integrated antenna elements and compensating for the impact of a lightweight, flexible structure on a large antenna array are important steps in the realization of HALE UAVs for microwave applications such as passive remote sensing and communications.

  16. Josephson admittance spectroscopy application for frequency analysis of broadband THz antennas

    International Nuclear Information System (INIS)

    Volkov, O Yu; Divin, Yu Yu; Gubankov, V N; Gundareva, I I; Pavlovskiy, V V

    2010-01-01

    Application of Josephson admittance spectroscopy for the spectral analysis of a broad-band log-periodic superconducting antenna was demonstrated at the frequency range from 50 to 700 GHz. The [001]-tilt YBa 2 Cu 3 O 7-x bicrystal Josephson junctions, integrated with sinuous log-periodic YBa 2 Cu 3 O 7-x antennas, were fabricated on NdGaO 3 bicrystal substrates. A real part of the antenna admittance ReY(f) as a function of the frequency f was reconstructed from the modification of the dc current-voltage characteristic of the junction, induced by the antenna. Resonance features were observed in the recovered ReY(f)-spectra with a periodicity in the logarithmic frequency scale, corresponding to log-periodic geometry of the antenna. The ReY(f)-spectra, recovered by Josephson spectroscopy, were compared with the ReY(f)-spectra, obtained by CAD simulation, and both spectra were shown to be similar in their main features. A value of 23 was obtained for an effective permittivity of the NdGaO3 bicrystal substrates by fitting simulated data to those obtained from Josephson spectroscopy.

  17. 47 CFR 27.56 - Antenna structures; air navigation safety.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Antenna structures; air navigation safety. 27... SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Technical Standards § 27.56 Antenna structures; air navigation safety. A licensee that owns its antenna structure(s) must not allow such antenna structure(s) to...

  18. 47 CFR 17.4 - Antenna structure registration.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Antenna structure registration. 17.4 Section 17... ANTENNA STRUCTURES General Information § 17.4 Antenna structure registration. (a) Effective July 1, 1996, the owner of any proposed or existing antenna structure that requires notice of proposed construction...

  19. 47 CFR 24.55 - Antenna structures; air navigation safety.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Antenna structures; air navigation safety. 24... SERVICES PERSONAL COMMUNICATIONS SERVICES Technical Standards § 24.55 Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become a...

  20. 47 CFR 73.1213 - Antenna structure, marking and lighting.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Antenna structure, marking and lighting. 73... SERVICES RADIO BROADCAST SERVICES Rules Applicable to All Broadcast Stations § 73.1213 Antenna structure... of Antenna Structures), requires certain antenna structures to be painted and/or lighted in...

  1. JPL-ANTOPT antenna structure optimization program

    Science.gov (United States)

    Strain, D. M.

    1994-11-01

    New antenna path-length error and pointing-error structure optimization codes were recently added to the MSC/NASTRAN structural analysis computer program. Path-length and pointing errors are important measured of structure-related antenna performance. The path-length and pointing errors are treated as scalar displacements for statics loading cases. These scalar displacements can be subject to constraint during the optimization process. Path-length and pointing-error calculations supplement the other optimization and sensitivity capabilities of NASTRAN. The analysis and design functions were implemented as 'DMAP ALTERs' to the Design Optimization (SOL 200) Solution Sequence of MSC-NASTRAN, Version 67.5.

  2. 47 CFR 78.63 - Antenna structure marking and lighting.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Antenna structure marking and lighting. 78.63... CABLE TELEVISION RELAY SERVICE General Operating Requirements § 78.63 Antenna structure marking and lighting. The owner of each antenna structure is responsible for ensuring that the structure, if required...

  3. 47 CFR 74.30 - Antenna structure, marking and lighting.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Antenna structure, marking and lighting. 74.30... Applicable to All Services in Part 74 § 74.30 Antenna structure, marking and lighting. The provisions of part 17 of the FCC rules (Construction, Marking, and Lighting of Antenna Structures) require certain...

  4. 47 CFR 74.22 - Use of common antenna structure.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Use of common antenna structure. 74.22 Section... Applicable to All Services in Part 74 § 74.22 Use of common antenna structure. The simultaneous use of a common antenna structure by more than one station authorized under this part, or by one or more stations...

  5. MUTUAL COUPLING REDUCTION BETWEEN MICROSTRIP ANTENNAS USING ELECTROMAGNETIC BANDGAP STRUCTURE

    Directory of Open Access Journals (Sweden)

    G.N. Gaikwad

    2011-03-01

    Full Text Available When the number of antenna elements is placed in forming the arrays, mutual coupling between the antenna elements is a critical issue. This is particularly concern in phase array antennas. Mutual coupling is a potential source of performance degradation in the form of deviation of the radiation pattern from the desired one, gain reduction due to excitation of surface wave, increased side lobe levels etc. EBG (Electromagnetic Band Gap structure (also called as Photonic Bandgap Structure PBG not only enhances the performance of the patch antennas but also provides greater amount of isolation when placed between the microstrip arrays. This greatly reduces the mutual coupling between the antenna elements. The radiation efficiency, gain, antenna efficiency, VSWR, frequency, directivity etc greatly improves over the conventional patch antennas using EBG. The EBG structure and normal patch antenna is simulated using IE3D antenna simulation software.

  6. Review of Large Spacecraft Deployable Membrane Antenna Structures

    Science.gov (United States)

    Liu, Zhi-Quan; Qiu, Hui; Li, Xiao; Yang, Shu-Li

    2017-11-01

    The demand for large antennas in future space missions has increasingly stimulated the development of deployable membrane antenna structures owing to their light weight and small stowage volume. However, there is little literature providing a comprehensive review and comparison of different membrane antenna structures. Space-borne membrane antenna structures are mainly classified as either parabolic or planar membrane antenna structures. For parabolic membrane antenna structures, there are five deploying and forming methods, including inflation, inflation-rigidization, elastic ribs driven, Shape Memory Polymer (SMP)-inflation, and electrostatic forming. The development and detailed comparison of these five methods are presented. Then, properties of membrane materials (including polyester film and polyimide film) for parabolic membrane antennas are compared. Additionally, for planar membrane antenna structures, frame shapes have changed from circular to rectangular, and different tensioning systems have emerged successively, including single Miura-Natori, double, and multi-layer tensioning systems. Recent advances in structural configurations, tensioning system design, and dynamic analysis for planar membrane antenna structures are investigated. Finally, future trends for large space membrane antenna structures are pointed out and technical problems are proposed, including design and analysis of membrane structures, materials and processes, membrane packing, surface accuracy stability, and test and verification technology. Through a review of large deployable membrane antenna structures, guidance for space membrane-antenna research and applications is provided.

  7. Nonlinear properties of double and triple barrier resonant tunneling structures in the sub-THz range

    International Nuclear Information System (INIS)

    Karuzskij, A.L.; Perestoronin, A.V.; Volchkov, N.A.

    2012-01-01

    The high-frequency nonlinear properties of GaAs/AlAs resonant tunneling diode (RTD) nanostructures and perspectives of implementation of the quantum regime of amplification in such structures, which is especially efficient in the range of sub-THz and THz ranges, are investigated. It is shown that in a triple barrier RTD the symmetry between the processes of amplification and dissipation can be avoided because of the interaction of an electromagnetic wave with both of resonant states in two quantum wells, that results in the significant growth of an RTD efficiency [ru

  8. Linear optical absorption spectra of mesoscopic structures in intense THz fields: Free-particle properties

    DEFF Research Database (Denmark)

    Johnsen, Kristinn; Jauho, Antti-Pekka

    1998-01-01

    We theoretically study the effect of THz radiation on the linear optical absorption spectra of semiconductor structures. A general theoretical framework, based on nonequilibrium Green functions, is formulated and applied to the calculation of linear optical absorption spectrum for several...... stable steps appear in the absorption spectrum when conditions for dynamical localization are met. [S0163-1829(95)03412-2]....

  9. Optimization of THz semi-insulating surface plasmon waveguide structures of GaSb/AlSb quantum cascade lasers

    Energy Technology Data Exchange (ETDEWEB)

    Ko, Yeong Hwan; Park, Bum Doo; Yu, Jae Su [Kyung Hee University, Yongin (Korea, Republic of)

    2012-11-15

    We designed and analyzed the semi-insulating surface plasmon waveguide structures of GaSb based quantum cascade lasers (QCLs) operating in the terahertz (THz) region of 2.6 - 6.5 THz using the finite element method. For improving the guiding property of THz QCL waveguide structures, a low threshold gain (g{sub th}) and a high optical confinement (Γ) could be achieved by optimizing the doping concentration and the thickness of plasma layer, the waveguide width, the substrate thickness, and the number of stages in active core region at various operating frequencies (2.6 - 6.5 THz). The effect of different substrates on the g{sub th} and Γ of THz QCL waveguide structures was also investigated.

  10. Charging induced damage on complex-antenna test structures

    NARCIS (Netherlands)

    Wang, Zhichun; Ackaert, Jan; Salm, Cora; Kuper, F.G.

    2001-01-01

    In this paper, new complex-antenna charging test structures are designed with antennas connected to the gate, source and drain of MOS transistors, and antennas connected to both plates of the metal-insulator-metalcapacitor (MIMC) devices. The measurement results show that the transistor is free of

  11. Broadband choke suppresses spurious currents in antenna structure

    Science.gov (United States)

    Bishop, O. L.; Bolt, C. A., Jr.

    1968-01-01

    Quarter-wavelength chokes are mounted on the coaxial line of an antenna structure to prevent induced spurious currents from affecting the antenna radiation frequency pattern. The choke-absorbent combination approximately doubled the usable frequency range for the antenna system studied.

  12. THz and Sub-THz Capabilities of a Table-Top Radiation Source Driven by an RF Thermionic Electron Gun

    Energy Technology Data Exchange (ETDEWEB)

    Smirnov, Alexei V.; Agustsson, R.; Boucher, S.; Campese, Tara; Chen, Y.C.; Hartzell, Josiah J.; Jocobson, B.T.; Murokh, A.; O' Shea, F.H.; Spranza, E.; Berg, W.; Borland, M.; Dooling, J. C.; Erwin, L.; Lindberg, R. R.; Pasky, S.J.; Sereno, N.; Sun, Y.; Zholents, A.

    2017-06-01

    Design features and experimental results are presented for a sub-mm wave source [1] based on APS RF thermionic electron gun. The setup includes compact alpha-magnet, quadrupoles, sub-mm-wave radiators, and THz optics. The sub-THz radiator is a planar, oversized structure with gratings. Source upgrade for generation frequencies above 1 THz is discussed. The THz radiator will use a short-period undulator having 1 T field amplitude, ~20 cm length, and integrated with a low-loss oversized waveguide. Both radiators are integrated with a miniature horn antenna and a small ~90°-degree in-vacuum bending magnet. The electron beamline is designed to operate different modes including conversion to a flat beam interacting efficiently with the radiator. The source can be used for cancer diagnostics, surface defectoscopy, and non-destructive testing. Sub-THz experiment demonstrated a good potential of a robust, table-top system for generation of a narrow bandwidth THz radiation. This setup can be considered as a prototype of a compact, laser-free, flexible source capable of generation of long trains of Sub-THz and THz pulses with repetition rates not available with laser-driven sources.

  13. Design and development of conformal antenna composite structure

    Science.gov (United States)

    Xie, Zonghong; Zhao, Wei; Zhang, Peng; Li, Xiang

    2017-09-01

    In the manufacturing process of the common smart skin antenna, the adhesive covered on the radiating elements of the antenna led to severe deviation of the resonant frequency, which degraded the electromagnetic performance of the antenna. In this paper, a new component called package cover was adopted to prevent the adhesive from covering on the radiating elements of the microstrip antenna array. The package cover and the microstrip antenna array were bonded together as packaged antenna which was then embedded into the composite sandwich structure to develop a new structure called conformal antenna composite structure (CACS). The geometric parameters of the microstrip antenna array and the CACS were optimized by the commercial software CST microwave studio. According to the optimal results, the microstrip antenna array and the CACS were manufactured and tested. The experimental and numerical results of electromagnetic performance showed that the resonant frequency of the CACS was close to that of the microstrip antenna array (with error less than 1%) and the CACS had a higher gain (about 2 dB) than the microstrip antenna array. The package system would increase the electromagnetic radiating energy at the design frequency nearly 66%. The numerical model generated by CST microwave studio in this study could successfully predict the electromagnetic performance of the microstrip antenna array and the CACS with relatively good accuracy. The mechanical analysis results showed that the CACS had better flexural property than the composite sandwich structure without the embedment of packaged antenna. The comparison of the electromagnetic performance for the CACS and the MECSSA showed that the package system was useful and effective.

  14. A New Method for Simulating Power Flow Density Focused by a Silicon Lens Antenna Irradiated with Linearly Polarized THz Wave

    Directory of Open Access Journals (Sweden)

    Catur Apriono

    2015-08-01

    Full Text Available A terahertz system uses dielectric lens antennas for focusing and collimating beams of terahertz wave radiation. Linearly polarized terahertz wave radiation has been widely applied in the terahertz system. Therefore, an accurate method for analyzing the power flow density in the dielectric lens antenna irradiated with the linearly polarized terahertz wave radiation is important to design the terahertz systems. In optics, ray-tracing method has been used to calculate the power flow density by a number density of rays. In this study, we propose a method of ray-tracing combined with Fresnel’s transmission, including transmittance and polarization of the terahertz wave radiation to calculate power flow density in a Silicon lens antenna. We compare power flow density calculated by the proposed method with the regular ray-tracing method. When the Silicon lens antenna is irradiated with linearly polarized terahertz wave radiation, the proposed method calculates the power flow density more accurately than the regular ray-tracing.

  15. A New Metasurface Superstrate Structure for Antenna Performance Enhancement

    Directory of Open Access Journals (Sweden)

    Mohammad Rashed Iqbal Faruque

    2013-07-01

    Full Text Available A new metasurface superstrate structure (MSS-loaded dual band microstrip line-fed small patch antenna is presented in this paper. The proposed antenna was designed on a ceramic-filled bioplastic sandwich substrate with a high dielectric constant. The proposed 7 × 6 element, square-shaped, single-sided MSS significantly improved the bandwidth and gain of the proposed antenna. The proposed MSS incorporated a slotted patch antenna that effectively increased the measured operating bandwidth from 13.3% to 18.8% and from 14.8% to 23.2% in the lower and upper bands, respectively. Moreover, the average gain of the proposed MSS-based antenna was enhanced from 2.12 dBi to 3.02 dBi in the lower band and from 4.10 dBi to 5.28 dBi in the upper band compared to the patch antenna alone. In addition to the bandwidth and gain improvements, more directive radiation characteristics were also observed from the MSS antenna compared to the patch itself. The effects of the MSS elements and the ground plane length on the reflection coefficient of the antenna were analyzed and optimized. The overall performance makes the proposed antenna appropriate for RFID and WLAN applications.

  16. A New Metasurface Superstrate Structure for Antenna Performance Enhancement.

    Science.gov (United States)

    Islam, Mohammad Tariqul; Ullah, Mohammad Habib; Singh, Mandeep Jit; Faruque, Mohammad Rashed Iqbal

    2013-07-31

    A new metasurface superstrate structure (MSS)-loaded dual band microstrip line-fed small patch antenna is presented in this paper. The proposed antenna was designed on a ceramic-filled bioplastic sandwich substrate with a high dielectric constant. The proposed 7 × 6 element, square-shaped, single-sided MSS significantly improved the bandwidth and gain of the proposed antenna. The proposed MSS incorporated a slotted patch antenna that effectively increased the measured operating bandwidth from 13.3% to 18.8% and from 14.8% to 23.2% in the lower and upper bands, respectively. Moreover, the average gain of the proposed MSS-based antenna was enhanced from 2.12 dBi to 3.02 dBi in the lower band and from 4.10 dBi to 5.28 dBi in the upper band compared to the patch antenna alone. In addition to the bandwidth and gain improvements, more directive radiation characteristics were also observed from the MSS antenna compared to the patch itself. The effects of the MSS elements and the ground plane length on the reflection coefficient of the antenna were analyzed and optimized. The overall performance makes the proposed antenna appropriate for RFID and WLAN applications.

  17. THz TDS of substance covered by disordered structure

    Science.gov (United States)

    Trofimov, V. A.; Zagursky, D. Y.; Zakharova, I. G.

    2016-04-01

    Computer simulation of a few-cycle pulse interaction with a substance covered by disordered structure is performed in order to study the effects imposed on spectra of transmitted and reflected pulses by presence of the cover. The substance is described by semi-classic approach and the cover is described by classic electrodynamics equations for linear isotropic medium. The cover consists of a number of layers with different properties which is considered to be the cause of the distortions. The influence of relation between pulse wavelength and cover layer thickness is illustrated. Computer simulation results are compared with those of physical experiments conducted for paper and other common materials.

  18. Field reconstruction and estimation of the antenna support structure effect on the measurement uncertainty of the BTS1940 antenna

    DEFF Research Database (Denmark)

    Cappellin, Cecilia; Pivnenko, Sergey

    2014-01-01

    The 3D reconstruction algorithm of DIATOOL is applied to the BTS1940 antenna, recently measured at the DTUESA Spherical Near-Field Antenna Test Facility in Denmark. The antenna was measured mounted on the antenna tower through a custom support structure. The purpose of this paper is to investigat...... by traditional microwave holography and by the inverse Fourier transform of the plane wave spectrum with knowledge of the invisible region....

  19. High-Frequency Antenna Arrays and Coupling Structures

    Data.gov (United States)

    National Aeronautics and Space Administration — We are fabricating antenna arrays and coupling structure for frequencies in the 200-300 GHz frequency bands. The primary motivation of this work is to develop...

  20. THz wiggler applied for measurements of electron bunch longitudinal structure in FEL

    Science.gov (United States)

    Syresin, E.; Kostromin, S.; Krasilnikov, M.; Makarov, R.; Morozov, N.; Petrov, D.

    2015-01-01

    The infrared undulator manufactured at JINR and installed at FLASH in 2007 is used for longitudinal bunch shape measurements in the range of several tenths of a micrometer. The presented electromagnetic wiggler is intended for generating a narrow-band THz radiation to measure the longitudinal electron bunch structure in FELs with an electron energy of several tens of MeV. This is a planar electromagnetic device with six regular periods, each 30 cm long. The K parameter is varied in the range 0.5-7.12 corresponding to the range B = 0.025-0.356 T of the peak field on the axis. The wiggler is simulated for 19.8 MeV/ c corresponding to the possible FEL option at PITZ. The wavelength range is 126 μm - 5.1 mm for this electron beam momentum. The 3D Opera simulations of the THz wiggler are discussed. A new PITZ photocathode laser system is proposed for the optimized performance of the high-brightness electron beam. The main goal is a production of 3D ellipsoidal electron bunches with homogeneous charge density. The electromagnetic wiggler is supposed to be used for measuring the longitudinal shape of these electron bunches.

  1. Experimental Characterization of Extremely Broadband THz Impulse Radio Communication Systems

    DEFF Research Database (Denmark)

    Yu, Xianbin; Vidal, Borja; Galili, Michael

    2015-01-01

    We experimentally characterize a ultrabroadband terahertz (THz) impulse radio system with up to 10 GHz repetition rate. THz generation and radiation are realized in an antenna-integrated uni-traveling-carrier photodiode (UTC-PD), and THz reception is implemented based on photoconductive sampling...

  2. Antennas.

    Science.gov (United States)

    1980-09-15

    it is shown in Fig. 2a and b (curves 3). If antenna forms/shapes sum-and-difference type diagram, its fundamantal parameter is product %’S or .< I...the solution of this problem for some special cases. ENDCOTNOTE. This solution will make it possible to manage without labor-consuming and not very

  3. Minimum Lens Size Supporting the Leaky-Wave Nature of Slit Dipole Antenna at Terahertz Frequency

    Directory of Open Access Journals (Sweden)

    Niamat Hussain

    2016-01-01

    Full Text Available We designed a slit dipole antenna backed by an extended hemispherical silicon lens and investigated the minimum lens size in which the slit dipole antenna works as a leaky-wave antenna. The slit dipole antenna consists of a planar feeding structure, which is a center-fed and open-ended slot line. A slit dipole antenna backed by an extended hemispherical silicon lens is investigated over a frequency range from 0.2 to 0.4 THz with the center frequency at 0.3 THz. The numerical results show that the antenna gain responses exhibited an increased level of sensitivity to the lens size and increased linearly with increasing lens radius. The lens with the radius of 1.2λo is found to be the best possible minimum lens size for a slit dipole antenna on an extended hemispherical silicon lens.

  4. On diversity performance of two-element coupling element based antenna structure for mobile terminal

    DEFF Research Database (Denmark)

    Al-Hadi, Azremi Abdullah; Toivanen, Juha; Laitinen, Tommi

    2010-01-01

    fading. The main challenge of antenna diversity in practical application is the integration of multiple antennas on a small ground plane. Two-element antenna structure based on coupling element antenna concept for diversity application has been studied in previous work and it has shown to be feasible...

  5. Novel Compact Spider Microstrip Antenna with New Defected Ground Structure

    Science.gov (United States)

    Ghoname, R. S.; Mohamed, M. A.; Hennawy, A. El.

    2012-08-01

    Two novel Defected Ground Structures (DGS) were first proposed, which have better results than that of the dumbbell (published shape). Using the general model of DGS, its equivalent parameters were extracted. The two new proposed shapes of DGS were then used to design a novel compact spider microstrip antenna to minimize its area. The size of the developed antenna was reduced to about 90.5% of that of the conventional one. This antenna with two different novel shapes of DGS was designed and simulated by using the ready-made software package Zeland-IE3D. Finally, it was fabricated by using thin film and photolithographic technique and measured by using vector network analyzer. Good agreements were found between the simulated and measured results.

  6. Thermo-mechanical Characteristics of Smart Skin Antenna Structures

    Science.gov (United States)

    Lee, Chang-Yull; Yoo, Kwang-Kyu; Kim, Ji-Hwan

    Analysis on the thermo-mechanical behaviors of smart skin antenna structures under air flow is performed. The model is a conformal load-bearing structure, reducing radar cross section and increasing stealth functions are very important. The skin is modeled as a multi-layer sandwich structure composed of carbon/epoxy, glass/epoxy and a dielectric polymer. Furthermore, a dielectric layer is embedded on the middle surface of the sandwich structure to act as antenna or radars. The formulation of the structural model is based on the first-order shear deformation plate theory. Lastly, Newton-Raphson iterative method applied for solving the nonlinear equations of the thermal postbuckling analysis and numerical results are calculated by finite element method.

  7. Analysis of photonic crystal and multi-frequency terahertz microstrip patch antenna

    International Nuclear Information System (INIS)

    Yang, Lechen; Shi, Xueshun; Chen, Kunfeng; Fu, Kai; Zhang, Baoshun

    2013-01-01

    In this paper, two-dimensional photonic crystals working at terahertz (THz) frequency is analyzed, a multi-frequency terahertz microstrip patch antenna on photonic crystal substrate is presented and its electromagnetic wave propagation phenomenon is investigated. The proposed antenna can work at five frequency points' scope at terahertz frequency regions, and the radiation efficiency is as high as ∼96%. The photonic crystal structure of the substrate is used to enhance the gain, directivity and radiation efficiency of the antenna

  8. Analysis of photonic crystal and multi-frequency terahertz microstrip patch antenna

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Lechen, E-mail: yanglechen@163.com [The 41st Research Institute of CETC, Qingdao 266555, Shandong Province (China); Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, Suzhou 215123, Jiangsu Province (China); Key Laboratory of Nanodevices and Applications, Chinese Academy of Science, Suzhou 215123, Jiangsu Province (China); Shi, Xueshun [The 41st Research Institute of CETC, Qingdao 266555, Shandong Province (China); Science and Technology on Electronic Test and Measurement Laboratory, Qingdao 266555, Shandong Province (China); Chen, Kunfeng [The 41st Research Institute of CETC, Qingdao 266555, Shandong Province (China); Fu, Kai; Zhang, Baoshun [Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, Suzhou 215123, Jiangsu Province (China); Key Laboratory of Nanodevices and Applications, Chinese Academy of Science, Suzhou 215123, Jiangsu Province (China)

    2013-12-15

    In this paper, two-dimensional photonic crystals working at terahertz (THz) frequency is analyzed, a multi-frequency terahertz microstrip patch antenna on photonic crystal substrate is presented and its electromagnetic wave propagation phenomenon is investigated. The proposed antenna can work at five frequency points' scope at terahertz frequency regions, and the radiation efficiency is as high as ∼96%. The photonic crystal structure of the substrate is used to enhance the gain, directivity and radiation efficiency of the antenna.

  9. 47 CFR 17.7 - Antenna structures requiring notification to the FAA.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Antenna structures requiring notification to..., MARKING, AND LIGHTING OF ANTENNA STRUCTURES Federal Aviation Administration Notification Criteria § 17.7 Antenna structures requiring notification to the FAA. A notification to the Federal Aviation...

  10. 47 CFR 101.119 - Simultaneous use of common antenna structures.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Simultaneous use of common antenna structures. 101.119 Section 101.119 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND... antenna structures. The simultaneous use of common antenna structures by more than one radio station, or...

  11. TLM modeling and system identification of optimized antenna structures

    Directory of Open Access Journals (Sweden)

    N. Fichtner

    2008-05-01

    Full Text Available The transmission line matrix (TLM method in conjunction with the genetic algorithm (GA is presented for the bandwidth optimization of a low profile patch antenna. The optimization routine is supplemented by a system identification (SI procedure. By the SI the model parameters of the structure are estimated which is used for a reduction of the total TLM simulation time. The SI utilizes a new stability criterion of the physical poles for the parameter extraction.

  12. Computer-aided design of antenna structures and components

    Science.gov (United States)

    Levy, R.

    1976-01-01

    This paper discusses computer-aided design procedures for antenna reflector structures and related components. The primary design aid is a computer program that establishes cross sectional sizes of the structural members by an optimality criterion. Alternative types of deflection-dependent objectives can be selected for designs subject to constraints on structure weight. The computer program has a special-purpose formulation to design structures of the type frequently used for antenna construction. These structures, in common with many in other areas of application, are represented by analytical models that employ only the three translational degrees of freedom at each node. The special-purpose construction of the program, however, permits coding and data management simplifications that provide advantages in problem size and execution speed. Size and speed are essentially governed by the requirements of structural analysis and are relatively unaffected by the added requirements of design. Computation times to execute several design/analysis cycles are comparable to the times required by general-purpose programs for a single analysis cycle. Examples in the paper illustrate effective design improvement for structures with several thousand degrees of freedom and within reasonable computing times.

  13. Terahertz (THz) Wireless Systems for Space Applications

    Science.gov (United States)

    Hwu, Shian U.; deSilva, Kanishka B.; Jih, Cindy T.

    2013-01-01

    NASA has been leading the Terahertz (THz) technology development for the sensors and instruments in astronomy in the past 20 years. THz technologies are expanding into much broader applications in recent years. Due to the vast available multiple gigahertz (GHz) broad bandwidths, THz radios offer the possibility for wireless transmission of high data rates. Multi-Gigabits per second (MGbps) broadband wireless access based on THz waves are closer to reality. The THz signal high atmosphere attenuation could significantly decrease the communication ranges and transmittable data rates for the ground systems. Contrary to the THz applications on the ground, the space applications in the atmosphere free environment do not suffer the atmosphere attenuation. The manufacturing technologies for the THz electronic components are advancing and maturing. There is great potential for the NASA future high data wireless applications in environments with difficult cabling and size/weight constraints. In this study, the THz wireless systems for potential space applications were investigated. The applicability of THz systems for space applications was analyzed. The link analysis indicates that MGbps data rates are achievable with compact sized high gain antennas.

  14. THz - ToF Optical Layer Analysis (OLA) to determine optical properties of dielectric materials

    Science.gov (United States)

    Spranger, Holger; Beckmann, Jörg

    2017-02-01

    Electromagnetic waves with frequencies between 0.1 and 10 THz are described as THz-radiation (T-ray). The ability to penetrate dielectric materials makes T-rays attractive to reveal discontinuities in polymer and ceramic materials. THz-Time Domain Spectroscopy Systems (THz-TDS) are available on the market today which operates with THz-pulses transmitted and received by optically pumped semiconductor antennas. In THz-TDS the travelling time (ToF) and shape of the pulse is changed if it interacts with the dielectric material and its inherent discontinuities. A tomogram of the object under the test can be reconstructed from time of flight diffraction (ToFD) scans if a synthetic focusing aperture (SAFT) algorithm is applied. The knowledge of the base materials shape and optical properties is essential for a proper reconstruction result. To obtain these properties a model is assumed which describes the device under the test as multilayer structure composed of thin layers with different dielectric characteristics. The Optical Layer Analysis (OLA) is able to fulfill these requirements. A short description why the optical properties are crucial for meaningful SAFT reconstruction results will be given first. Afterwards the OLA will be derived and applied on representative samples to discuss and evaluate its benefits and limits.

  15. THz Dynamic Nuclear Polarization NMR.

    Science.gov (United States)

    Nanni, Emilio A; Barnes, Alexander B; Griffin, Robert G; Temkin, Richard J

    2011-08-29

    Dynamic nuclear polarization (DNP) increases the sensitivity of nuclear magnetic resonance (NMR) spectroscopy by using high frequency microwaves to transfer the polarization of the electrons to the nuclear spins. The enhancement in NMR sensitivity can amount to a factor of well above 100, enabling faster data acquisition and greatly improved NMR measurements. With the increasing magnetic fields (up to 23 T) used in NMR research, the required frequency for DNP falls into the THz band (140-600 GHz). Gyrotrons have been developed to meet the demanding specifications for DNP NMR, including power levels of tens of watts; frequency stability of a few megahertz; and power stability of 1% over runs that last for several days to weeks. Continuous gyrotron frequency tuning of over 1 GHz has also been demonstrated. The complete DNP NMR system must include a low loss transmission line; an optimized antenna; and a holder for efficient coupling of the THz radiation to the sample. This paper describes the DNP NMR process and illustrates the THz systems needed for this demanding spectroscopic application. THz DNP NMR is a rapidly developing, exciting area of THz science and technology.

  16. Simulation of photoconductive antennas for terahertz radiation

    Directory of Open Access Journals (Sweden)

    Carlos Criollo

    2015-01-01

    Full Text Available Simulation of terahertz (THz emission based on PC antennas imposes a challenge to couple the semiconductor carrier phenomena, optical transport and the THz energy transport. In this paper a Multi-physics simulation for coupling these phenomena using COMSOL Multi-physics 4.3b is introduced. The main parameters of THz photoconductive (PC antenna as THz emitter have been reviewed and discussed. The results indicate the role of each parameter in the resulting photocurrent waveform and THz frequency: The radiated THz photocurrent waveform is determined by the photoconductive gap (the separation between the metallic electrodes, the incident laser illumination and the DC excitation voltage; while the THz frequency depends on the dipole length. The optimization of these parameters could enhance the emission. The simulations extend the advance of compact and cost-effective THz emitters.

  17. A High Isolation MIMO Antenna without Decoupling Structure for LTE 700 MHz

    Directory of Open Access Journals (Sweden)

    Yanjie Wu

    2015-01-01

    Full Text Available This paper presents a long-term evolution (LTE 700 MHz band multiple-input-multiple-output (MIMO antenna, and high isolation between the two symmetrical antenna elements is obtained without introducing extra decoupling structure. Each antenna element is a combination antenna of PIFA and a meander monopole antenna. The end of the PIFA and the meander monopole antenna are, respectively, overlapped with the 50 Ω microstrip feed line, the two overlapping areas produce additional capacitance which can be considered decoupling structures to enhance the isolation for the MIMO antenna, as well as the impedance matching of the antenna elements. The MIMO antenna is etched on FR4 PCB board with dimensions of 71 × 40 × 1.6 mm3; the edge-to-edge separation of the two antenna elements is only nearly 0.037 λ at 700 MHz. Both simulation and measurement results are used to confirm the MIMO antenna performance; the operating bandwidth is 698–750 MHz with S11≤−6 dB and S21≤−23 dB.

  18. A Near-Zero Refractive Index Meta-Surface Structure for Antenna Performance Improvement

    Science.gov (United States)

    Ullah, Mohammad Habib; Islam, Mohammad Tariqul; Faruque, Mohammad Rashed Iqbal

    2013-01-01

    A new meta-surface structure (MSS) with a near-zero refractive index (NZRI) is proposed to enhance the performance of a square loop antenna array. The main challenge to improve the antenna performance is increment of the overall antenna volume that is mitigated by assimilating the planar NZRI MSS at the back of the antenna structure. The proposed NZRI MSS-loaded CPW-fed (Co-Planar Waveguide) four-element array antenna is designed on ceramic-bioplastic-ceramic sandwich substrate using high-frequency structure simulator (HFSS), a finite-element-method-based simulation tool. The gain and directivity of the antenna are significantly enhanced by incorporating the NZRI MSS with a 7 × 6 set of elements at the back of the antenna structure. Measurement results show that the maximum gains of the antenna increased from 6.21 dBi to 8.25 dBi, from 6.52 dBi to 9.05 dBi and from 10.54 dBi to 12.15 dBi in the first, second and third bands, respectively. The effect of the slot configuration in the ground plane on the reflection coefficient of the antenna was analyzed and optimized. The overall performance makes the proposed antenna appropriate for UHFFM (Ultra High Frequency Frequency Modulation) telemetry-based space applications as well as mobile satellite, microwave radiometry and radio astronomy applications. PMID:28788376

  19. A Near-Zero Refractive Index Meta-Surface Structure for Antenna Performance Improvement

    Directory of Open Access Journals (Sweden)

    Mohammad Habib Ullah

    2013-11-01

    Full Text Available A new meta-surface structure (MSS with a near-zero refractive index (NZRI is proposed to enhance the performance of a square loop antenna array. The main challenge to improve the antenna performance is increment of the overall antenna volume that is mitigated by assimilating the planar NZRI MSS at the back of the antenna structure. The proposed NZRI MSS-loaded CPW-fed (Co-Planar Waveguide four-element array antenna is designed on ceramic-bioplastic-ceramic sandwich substrate using high-frequency structure simulator (HFSS, a finite-element-method-based simulation tool. The gain and directivity of the antenna are significantly enhanced by incorporating the NZRI MSS with a 7 × 6 set of elements at the back of the antenna structure. Measurement results show that the maximum gains of the antenna increased from 6.21 dBi to 8.25 dBi, from 6.52 dBi to 9.05 dBi and from 10.54 dBi to 12.15 dBi in the first, second and third bands, respectively. The effect of the slot configuration in the ground plane on the reflection coefficient of the antenna was analyzed and optimized. The overall performance makes the proposed antenna appropriate for UHFFM (Ultra High Frequency Frequency Modulation telemetry-based space applications as well as mobile satellite, microwave radiometry and radio astronomy applications.

  20. Nonlinear dynamics of semiconductors in strong THz electric fields

    DEFF Research Database (Denmark)

    Tarekegne, Abebe Tilahun

    weak THz and near infrared pulses as probes. Firstly, an intense THz pulse is used to study THz-induced impact ionization (IMI) dynamics in silicon. Local field enhancement by metallic dipole antenna arrays has been used to generate strong electric fields of several MV/cm in the hot spots near...... uniquely. Finally it is demonstrated for the first time that SiC can be tailored to have extremely fast THz-induced nonlinear behavior in moderate THz electric fields by addition of appropriate dopants. A 4H-SiC sample with high concentrations of nitrogen and boron dopants shows a nonlinear THz......In this thesis, we investigate nonlinear interactions of an intense terahertz (THz) field with semiconductors, in particular the technologically relevant materials silicon and silicon carbide. We reveal the time-resolved dynamics of the nonlinear processes by pump-probe experiments that involve...

  1. Conformal Lightweight Antenna Structures for Aeronautical Communication Technologies

    Science.gov (United States)

    Meador, Mary Ann

    2017-01-01

    This project is to develop antennas which enable beyond line of sight (BLOS) command and control for UAVs. We will take advantage of newly assigned provisional Ku-band spectrum for UAVs and use unique antenna designs to avoid interference with ground systems. This will involve designing antennas with high isotropic effective radiated power (EIRP) and ultra-low sidelobes. The antennas will be made with polymer aerogel as a substrate to both reduce weight and improve performance, as demonstrated in an Aero Seedling. In addition, designing the antennas to be conformal to the aircraft fuselage will reduce drag.

  2. Structural Modeling and Analysis on Dynamic Characteristics of Antenna Pedestal in Airborne SAR

    Directory of Open Access Journals (Sweden)

    He Li-ping

    2012-06-01

    Full Text Available Finite element modeling and structural dynamic characteristics of antenna pedestal in airborne SAR were studied in this paper. The Finite element model of antenna pedestal in airborne SAR was set up on the basis of structural dynamic theory, then, the key technologies of dynamic simulation were pointed out, and the modal analysis and transient analysis were carried out. Simulation results show that the dynamic characteristics of antenna pedestal in airborne SAR can meet the requirements of servo bandwidth and structural strength. The fast finite element modeling and simulation method proposed in this paper are of great significance to the weight reducing design of antenna pedestal in airborne SAR.

  3. Wall Painting Investigation by Means of Non-invasive Terahertz Time-Domain Imaging (THz-TDI): Inspection of Subsurface Structures Buried in Historical Plasters

    DEFF Research Database (Denmark)

    Dandolo, Corinna Ludovica Koch; Jepsen, Peter Uhd

    2016-01-01

    of terahertz time-domain imaging (THz-TDI). Subsurface structures have been detected at different depths inside the lime-based plaster of the wall painting until approximately 1 cm from the surface. The surface morphology of the buried structures has been 3D imaged in detail, providing a substantial...

  4. Room-Temperature Oscillation of Resonant Tunneling Diodes close to 2 THz and Their Functions for Various Applications

    Science.gov (United States)

    Asada, Masahiro; Suzuki, Safumi

    2016-12-01

    Compact and coherent source is a key component for various applications of the terahertz (THz) wave. We report on our recent results of THz oscillators using resonant tunneling diodes (RTDs). To achieve high-frequency oscillation, the electron delay time of RTD was reduced with a narrow quantum well and an optimized collector spacer thickness. Conduction loss at the air bridge connecting RTD and slot antenna, which works as a resonator and a radiator, was also reduced. By these structures, a fundamental oscillation up to 1.92 THz was obtained at room temperature. Theoretical calculation shows that an oscillation over 2 THz is further expected by improved structures of RTD and antenna. Using the offset slot antenna and two-element array configuration, high output power of 0.61 mW was obtained at 620 GHz. A direct intensity modulation of RTD oscillators up to 30 GHz, which is useful for high-speed wireless data transmission, was demonstrated. By the integration of a varactor diode, wide frequency sweep of 580-700 GHz in a single device and 580-900 GHz in a four-element array were also demonstrated. This result expands possible applications of RTD oscillators.

  5. Single crystal Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8} structures as THz-emitters

    Energy Technology Data Exchange (ETDEWEB)

    Wieland, Raphael; Rudau, Fabian; Langer, Julian; Koelle, Dieter; Kleiner, Reinhold [Physikalisches Institut and Center for Collective Quantum Phenomena in LISA+, Universitaet Tuebingen, Tuebingen (Germany); Kinev, Nickolay; Koshelets, Valery [Kotel' nikov Institute of Radio Engineering and Electronics, Moscow (Russian Federation); Yuan, Jie; Ishii, Akira; Hatano, Takeshi [National Institute for Materials Science, Tsukuba (Japan); Huang, Ya; Ji, Min; Zhou, Xianjing; Wang, Huabing [National Institute for Materials Science, Tsukuba (Japan); Research Institute of Superconductor Electronics, Nanjing University, Nanjing (China); Wu, Peiheng [Research Institute of Superconductor Electronics, Nanjing University, Nanjing (China)

    2016-07-01

    By means of Josephson Junctions (JJs) one can easily convert a dc voltage into high-frequency electromagnetic radiation. The high-Tc superconductor Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8} (BSCCO) has a layered crystal structure in such a way that JJs form intrinsically. This allows to fabricate hundreds of stacked junctions with reasonable effort. Terahertz emission can be observed at relatively low bias currents but also at higher input power. Emission frequencies from 0.4 to 2.4 THz have been measured. A hot spot forms at high bias currents with effect on both intensity and linewidth of the THz emission.BSCCO mesas probably act as a cavity for electromagnetic standing waves that synchronize all junctions in the stack. We investigated hotspot formation and THz emission using a combination of transport measurements, low temperature scanning laser microscopy and electromagnetic wave detection via a superconducting receiver.

  6. Plasma ICR heating antennas: adaptation, radiated field structure, coupling

    International Nuclear Information System (INIS)

    Pegourie, B.

    1982-01-01

    The transmission line theory has been used to find the antenna adapattion improvement possibilities, so as to optimize the power transfer from generator to plasma. ICR heating antennas are described, radiated magnetic field is measured, and superstructures (diaphragms and electrostatic screen) is studied from a mock-up and a numerical model. Results about antenna radiation and electric property modifications due to superstructures, without plasma, are presented. At last, TFR antenna coupling properties, in terms of frequency, electromagnetic wave and plasma conditions, are studied. In the whole work, we tried to define, when possible the construction criteria fitted to cyclotron heating in the big tokamak experiments under construction [fr

  7. Body-insensitive Multi-Mode MIMO Terminal Antenna of Double-Ring Structure

    DEFF Research Database (Denmark)

    Zhao, Kun; Zhang, Shuai; Ishimiya, Katsunori

    2015-01-01

    In this paper, we propose a novel multimode multi-input multi-output (MIMO) antenna system composed of a dual-element MIMO cellular antenna and dual-element MIMO Wi-Fi antenna for mobile terminal applications. The antenna system has a double-ring structure and can be integrated with the metal frame...... of mobile terminals. With the multimode excitation, the MIMO cellular antenna can operate at 830-900 MHz, 1700-2200 MHz, and 2400-2700 MHz, for 2G, 3G, and LTE bands, respectively. The MIMO Wi-Fi antenna can cover two Wi-Fi bands from 2.4 to 2.5 GHz and from 5.2 to 5.8 GHz. The effect of a user's body...

  8. A Novel Wideband Magneto-Electric Dipole Antenna with Improved Feeding Structure

    Directory of Open Access Journals (Sweden)

    N. Marwah

    2016-08-01

    Full Text Available A novel feeding structure in magneto-electric dipole antenna is proposed and analyzed, which is simpler and better in performance than previous designs, involving differential feeding.  Due to this improved feeding structure, the antenna has achieved an impedance bandwidth of 133.3% ( 0.5 GHz – 2.5 GHz, resulting into an ultra-wide band antenna. The maximum broadside gain 7.5dBi with unidirectional radiation pattern has also been reported for the entire the range of operation. Symmetry in E-plane and H-plane radiation patterns has been observed due to the symmetry in structure and excitation of antenna. The antenna has also been able to achieve cross polarization levels.

  9. THz emission of donor and acceptor doped GaAs/AlGaAs quantum well structures with inserted thin AlAs monolayer

    Science.gov (United States)

    van Dommelen, Paphavee; Daengngam, Chalongrat; Kalasuwan, Pruet

    2018-04-01

    In this paper, we explore THz range optical intersubband transition energies in a donor doped quantum well of a GaAs/AlGaAs system as a function of the insertion position of an AlAs monolayer in the GaAs quantum well. In simulated models, the optical transition energies between electron subband levels 1 and 2 were higher in the doped structure than in the undoped structure. This may be because the envelope wave function of the second electron subband strongly overlapped the envelope wave function of the first electron subband and influenced the optical intersubband transition between the two levels in the THz range. At different levels of bias voltage at the Schottky barrier on the donor doped structure, the electric field in the growth direction of the structure linearly increased the further away the AlAs monolayer was placed from the reference position. We also simulated the optical transition energies between acceptor energy levels of the acceptor doped structure as a function of the insertion position of the AlAs monolayer. The acceptor doped structure induced THz range emission whereas the undoped structure induced mid-IR emission.

  10. Slow and fast light in SOA-EA structures for phased-array antennas

    DEFF Research Database (Denmark)

    Sales, S.; Öhman, Filip; Bermejo, A.

    We present an SOA-EA structure for controlling the phase and amplitude of optically fed phased-array antennas. Phase shifts of 40 degrees are obtained through slow and fast light effects by changing only the reverse voltage.......We present an SOA-EA structure for controlling the phase and amplitude of optically fed phased-array antennas. Phase shifts of 40 degrees are obtained through slow and fast light effects by changing only the reverse voltage....

  11. Optical Interconnects for Smart Antenna Driver-Receiver-Switch System for Wireless Communication

    National Research Council Canada - National Science Library

    Esener, Sadik

    2002-01-01

    ... at 0.3THz-30THz for telecommunication applications in general and for interconnects within the box, in particular, for example for Smart Antenna Driver-Receiver-Switch System for Wireless Communication...

  12. A New Microstrip Filter Using CRLH Structure and Defected Ground Structure in Antenna Application

    Directory of Open Access Journals (Sweden)

    Xin Cao

    2014-01-01

    Full Text Available A new microstrip bandpass filter using composite right/left-handed (CRLH mushroom structure with interdigital capacitors and defected ground structure (DGS is proposed. The proposed filter uses CRLH mushroom structure working at its first negative resonance mode to create the passband and DGS to increase rejection outside the passband. Simulation and measurement results are in good agreement, and low in-band insertion loss and great out-band rejection have been achieved. It is demonstrated that the combination of CRLH mushroom structure with interdigital capacitors and DGS has succeeded in achieving excellent performance. This new filter can be applied in transmitting and receiving antennas.

  13. Structural Design of the DTU-ESA MM-Wave Validation Standard Antenna

    DEFF Research Database (Denmark)

    Branner, Kim; Berring, Peter; Markussen, Christen Malte

    2015-01-01

    in the range of temperatures 20±5°C under arbitrary orientation in the gravity field. The antenna has a characteristic length of approximately 500mm. And in order to obtain very low measuring error, the allowable deformations of the reflector and feeds are down to 2.5μm. The antenna is modelled structurally...... using the commercial finite element package MSC.Patran with MSC.MARC as solver. The solid parts of the antenna are meshed with 10-noded tetrahedral elements, which have quadratic shape functions and the entire model has approximately 325.000 elements. The individual solid part of the antenna...... is connected via a glued contact formulation in MSC.MARC. Because of the size and the complexity of the model a computer cluster is applied to solve the analyses. This paper describes the structural solution to meet these extremely strict stability requirements and the structural analyses done in order...

  14. AMELIORATE OF BANDWIDTH AND RETURN LOSS OF RECTANGULAR PATCH ANTENNA USING METAMATERIAL STRUCTURE FOR RFID TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    RAJESH SAHA

    2016-09-01

    Full Text Available Radio Frequency Identification is an emerging research topic to identify any object automatically and it has applications in many fields like manufacture industry, business, animal tracking, vehicle tracking etc. In automatic identification system, the main role of radio frequency identification system is radiation and detection. The reader and the tag are the important components in radio frequency identification technology. In radio frequency identification system, antenna plays very significant role to transmit and receive data in both direction (i.e., from reader to tag and vice versa. An antenna with high gain, high directivity, high bandwidth and more down in negative S11 (dB value works as an effective antenna. So design and optimization of an effective antenna is very necessary for any application. In this paper, firstly itdesigned a rectangular patch antenna and simulated through High Frequency Structure Simulator. In next step, it designed a metamaterial structure having U shape Split Ring Resonator with both one and two port, on the rectangular patch antenna to improve the return loss and bandwidth of patch antenna; so that the performance of the tag can be increased for the radio frequency identification system. By simulation it has been seen that, two port antenna provides maximum return loss and bandwidth of - 41.2dB and 870MHz respectively. Finally, the output parameters such as return loss, gain, directivity that are obtained from simulation of the metamaterial Split Ring Resonator structure antenna are compared with the network output of Artificial Neural Network to find the Mean Square Error between the simulated output and Artificial Neural Network output.

  15. Design of microstrip-fed printed UWB diversity antenna with tee crossed shaped structure

    OpenAIRE

    Raj Kumar; Gopal Surushe

    2016-01-01

    A compact, Ultra Wideband (UWB) antenna system for multi-input multi-output (MIMO)/diversity application is proposed. The antenna system is a microstrip structure with two similar triangular shaped radiating elements and a common ground plane. The radiating elements are excited by tapered feed for better impedance matching. A T-crossed shaped stub is added in the ground plane to increase the isolation between the two radiators. The overall dimension of the proposed antenna system is 46 mm × 3...

  16. Current responsivity of semiconductor superlattice THz-photon detectors

    DEFF Research Database (Denmark)

    Ignatov, Anatoly A.; Jauho, Antti-Pekka

    1999-01-01

    The current responsivity of a semiconductor superlattice THz-photon detector is calculated using an equivalent circuit model which takes into account the finite matching efficiency between a detector antenna and the superlattice in the presence of parasitic losses. Calculations performed for curr......The current responsivity of a semiconductor superlattice THz-photon detector is calculated using an equivalent circuit model which takes into account the finite matching efficiency between a detector antenna and the superlattice in the presence of parasitic losses. Calculations performed...... of the responsivity (2–3 A/W in the 1–3 THz-frequency band) range up to several percents of the quantum efficiency e/[h-bar] omega of an ideal superconductor tunnel junction detector. Properly designed semiconductor superlattice detectors may thus demonstrate better room temperature THz-photon responsivity than...

  17. Crack Monitoring Method for an FRP-Strengthened Steel Structure Based on an Antenna Sensor.

    Science.gov (United States)

    Liu, Zhiping; Chen, Kai; Li, Zongchen; Jiang, Xiaoli

    2017-10-20

    Fiber-reinforced polymer (FRP) has been increasingly applied to steel structures for structural strengthening or crack repair, given its high strength-to-weight ratio and high stiffness-to-weight ratio. Cracks in steel structures are the dominant hidden threats to structural safety. However, it is difficult to monitor structural cracks under FRP coverage and there is little related research. In this paper, a crack monitoring method for an FRP-strengthened steel structure deploying a microstrip antenna sensor is presented. A theoretical model of the dual-substrate antenna sensor with FRP is established and the sensitivity of crack monitoring is studied. The effects of the weak conductivity of carbon fiber reinforced polymers (CFRPs) on the performance of crack monitoring are analyzed via contrast experiments. The effects of FRP thickness on the performance of the antenna sensor are studied. The influence of structural strain on crack detection coupling is studied through strain-crack coupling experiments. The results indicate that the antenna sensor can detect cracks in steel structures covered by FRP (including CFRP). FRP thickness affects the antenna sensor's performance significantly, while the effects of strain can be ignored. The results provide a new approach for crack monitoring of FRP-strengthened steel structures with extensive application prospects.

  18. Multifunctional Material Systems for Reconfigurable Antennas in Superconfigurable Structures

    Science.gov (United States)

    2016-01-05

    accomplishments and other highlights from this research program. 15. SUBJECT TERMS Reconfigurable antennas, nanocomposites , dispersions, superconfigurable...and more repeatable yields; 3) establishing a process for functionalization of nanoparticle surface to provide multi-layer coatings to tune electric...composites to fabricate substrates with tailorable EM properties. W have also carried out the development of judicious coatings of above high aspect ratio

  19. Manufacturing error sensitivity analysis and optimal design method of cable-network antenna structures

    Science.gov (United States)

    Zong, Yali; Hu, Naigang; Duan, Baoyan; Yang, Guigeng; Cao, Hongjun; Xu, Wanye

    2016-03-01

    Inevitable manufacturing errors and inconsistency between assumed and actual boundary conditions can affect the shape precision and cable tensions of a cable-network antenna, and even result in failure of the structure in service. In this paper, an analytical sensitivity analysis method of the shape precision and cable tensions with respect to the parameters carrying uncertainty was studied. Based on the sensitivity analysis, an optimal design procedure was proposed to alleviate the effects of the parameters that carry uncertainty. The validity of the calculated sensitivities is examined by those computed by a finite difference method. Comparison with a traditional design method shows that the presented design procedure can remarkably reduce the influence of the uncertainties on the antenna performance. Moreover, the results suggest that especially slender front net cables, thick tension ties, relatively slender boundary cables and high tension level can improve the ability of cable-network antenna structures to resist the effects of the uncertainties on the antenna performance.

  20. A Novel Structure and Design Optimization of Compact Spline-Parameterized UWB Slot Antenna

    Directory of Open Access Journals (Sweden)

    Koziel Slawomir

    2016-12-01

    Full Text Available In this paper, a novel structure of a compact UWB slot antenna and its design optimization procedure has been presented. In order to achieve a sufficient number of degrees of freedom necessary to obtain a considerable size reduction rate, the slot is parameterized using spline curves. All antenna dimensions are simultaneously adjusted using numerical optimization procedures. The fundamental bottleneck here is a high cost of the electromagnetic (EM simulation model of the structure that includes (for reliability an SMA connector. Another problem is a large number of geometry parameters (nineteen. For the sake of computational efficiency, the optimization process is therefore performed using variable-fidelity EM simulations and surrogate-assisted algorithms. The optimization process is oriented towards explicit reduction of the antenna size and leads to a compact footprint of 199 mm2 as well as acceptable matching within the entire UWB band. The simulation results are validated using physical measurements of the fabricated antenna prototype.

  1. Generalized equivalent circuit model for ultra wideband antenna structure with double steps for energy scavenging

    International Nuclear Information System (INIS)

    Heong, Oon Kheng; Hock, Goh Chin; Chakrabarty, Chandan Kumar; Hock, Goh Tian

    2013-01-01

    There are various types of UWB antennas can be used to scavenge energy from the air and one of them is the printed disc monopole antenna. One of the new challenges imposed on ultra wideband is the design of a generalized antenna circuit model. It is developed in order to extract the inductance and capacitance values of the UWB antennas. In this research work, the developed circuit model can be used to represent the rectangular printed disc monopole antenna with double steps. The antenna structure is simulated with CST Microwave Studio, while the circuit model is simulated with AWR Microwave Office. In order to ensure the simulation result from the circuit model is accurate, the circuit model is also simulated using Mathlab program. The developed circuit model is found to be able to depict the actual UWB antenna. Energy harvesting from environmental wirelessly is an emerging method, which forms a promising alternative to existing energy scavenging system. The developed UWB can be used to scavenge wideband energy from electromagnetic wave present in the environment.

  2. Compact UWB Filtering-Antenna with Controllable WLAN Band Rejection Using Defected Microstrip Structure

    Directory of Open Access Journals (Sweden)

    A. Alhegazi

    2018-04-01

    Full Text Available An ultra-wideband (UWB filtering-antenna with controllable band notch is reported in this paper. The filtering-antenna consists of a modified monopole antenna and defected microstrip structure (DMS. The monopole antenna is modified using microstrip transition in the feedline and block with a triangular-shape slot on each side of the circular patch to produce wider impedance bandwidth with better return loss. The DMS is constructed using U-shaped slot etched on the feedline to provide band notch and remove WLAN band (5.1-5.8 GHz. A switch is employed in the DMS to control the created band notch. The measured results show that the proposed design exhibits a wide impedance bandwidth with controllable WLAN band rejection, realized peak gain of 4.85 dB and omnidirectional radiation pattern. Therefore, the proposed design is suitable for UWB applications.

  3. Design and analysis of coplanar waveguide triple-band antenna based on defected ground structure

    Science.gov (United States)

    Lv, Hong; Chen, Wanli; Xia, Xinsheng; Qi, Peng; Sun, Quanling

    2017-11-01

    A kind of coplanar waveguide triple-band antenna based on defected ground structure is proposed, which has novel structure. Three batches with different frequency band are constructed by utilizing line combination, overlapping, and symmetry method. Stop band signals among three frequency bands are effectively suppressed by slots with different structures. More satisfactory impedance matching is realized by means of changing slot structure and improving return-loss. The presented antenna can operates simultaneously in various systems such as 3G / 4G wireless communication, Bluetooth, Worldwide Interoperability for Microwave Access, Wireless LAN. Test results show that the antenna has good radiation and gain in its working frequency band, and that it has great application potentials.

  4. For progress in natural science: Materials international investigations of structural phase transformation and THz properties across metal–insulator transition in VO2/Al2O3 epitaxial films

    Directory of Open Access Journals (Sweden)

    Mengmeng Yang

    2015-10-01

    Full Text Available Vanadium dioxide (VO2 epitaxial thin films on (0001-oriented Al2O3 substrates were prepared using radio frequency (RF magnetron sputtering techniques. To study the metal-insulator-transition (MIT mechanism and extend the applications of VO2 epitaxial films at terahertz (THz band, temperature-dependent X-ray diffraction (XRD and THz time domain spectroscopy of the VO2 epitaxial films were performed. Both the lattice constants and THz transmission exhibited a similar and sharp transition that was similar to that observed for the electrical resistance. Consequently, the MIT of the VO2/Al2O3 epitaxial films should be co-triggered by the structural phase transition and electronic transition. Moreover, the very large resistance change (on the order of ~103 and THz response (with a transmission modulation ratio of ~87% in the VO2/Al2O3 epitaxial heterostructures are promising for electrical switch and electro-optical device applications.

  5. Design of microstrip-fed printed UWB diversity antenna with tee crossed shaped structure

    Directory of Open Access Journals (Sweden)

    Raj Kumar

    2016-06-01

    Full Text Available A compact, Ultra Wideband (UWB antenna system for multi-input multi-output (MIMO/diversity application is proposed. The antenna system is a microstrip structure with two similar triangular shaped radiating elements and a common ground plane. The radiating elements are excited by tapered feed for better impedance matching. A T-crossed shaped stub is added in the ground plane to increase the isolation between the two radiators. The overall dimension of the proposed antenna system is 46 mm × 32.6 mm × 1.6 mm. The measured impedance bandwidth (reflection coefficient < −10 dB is from 1.8 GHz to well beyond 12 GHz which covers the entire UWB region. A measured isolation of 15 dB or better is achieved in the UWB region. The diversity gain of the antenna system is close to 10 dBi and the envelope correlation coefficient is well below 0.2 in the operating band. Parametric study is also done to check the sensitivity of the antenna in terms of reflection coefficient and isolation to the different parameters. These characteristics show that the proposed antenna is suitable for the MIMO/diversity application.

  6. TCM Analysis of Defected Ground Structures for MIMO Antenna Designs in Mobile Terminals

    KAUST Repository

    Ghalib, Asim

    2017-08-14

    In this paper, the theory of characteristic modes (TCM) is used for the first time to analyze the behavior of defected ground structures (DGS) when added to antenna designs. A properly designed DGS introduces currents opposite in direction to the original characteristic modes (CM) currents thus reducing mutual coupling. TCM is also applied to multiple-inputmultiple- output (MIMO) antenna systems to develop a systematic approach that can predict whether the isolation can be enhanced further or not. For this purpose two 4-element and one 2-element MIMO designs, i.e. monopole and planar inverted-F antennas (PIFA) are studied. The addition of different antenna elements affects the CM significantly as well as differently. Some of the CM excited on the antenna surface contribute to the coupling between the antenna ports that is why they can be classified as coupling modes. To improve the isolation, the DGS should be introduced at certain locations that blocks the coupling modes but at the same time does not affect the non-coupling modes. If their is no such location or the current on the surface of the chassis for coupling and non-coupling modes is approximately same, the isolation cannot be enhanced further. Using this approach, isolation was improved on an average by 11 dB in all the designs considered, giving the most isolation enhancement following a systematic way compared to other works.

  7. Spirulina-templated metal microcoils with controlled helical structures for THz electromagnetic responses.

    Science.gov (United States)

    Kamata, Kaori; Piao, Zhenzi; Suzuki, Soichiro; Fujimori, Takahiro; Tajiri, Wataru; Nagai, Keiji; Iyoda, Tomokazu; Yamada, Atsushi; Hayakawa, Toshiaki; Ishiwara, Mitsuteru; Horaguchi, Satoshi; Belay, Amha; Tanaka, Takuo; Takano, Keisuke; Hangyo, Masanori

    2014-05-12

    Microstructures in nature are ultrafine and ordered in biological roles, which have attracted material scientists. Spirulina forms three-dimensional helical microstructure, one of remarkable features in nature beyond our current processing technology such as lithography in terms of mass-productivity and structural multiplicity. Spirulina varies its diameter, helical pitch, and/or length against growing environment. This unique helix is suggestive of a tiny electromagnetic coil, if composed of electro-conductive metal, which brought us main concept of this work. Here, we describe the biotemplating process onto Spirulina surface to fabricate metal microcoils. Structural parameters of the microcoil can be controlled by the cultivation conditions of Spirulina template and also purely one-handed microcoil can be fabricated. A microcoil dispersion sheet exhibited optically active response attributed to structural resonance in terahertz-wave region.

  8. Spirulina-Templated Metal Microcoils with Controlled Helical Structures for THz Electromagnetic Responses

    Science.gov (United States)

    Kamata, Kaori; Piao, Zhenzi; Suzuki, Soichiro; Fujimori, Takahiro; Tajiri, Wataru; Nagai, Keiji; Iyoda, Tomokazu; Yamada, Atsushi; Hayakawa, Toshiaki; Ishiwara, Mitsuteru; Horaguchi, Satoshi; Belay, Amha; Tanaka, Takuo; Takano, Keisuke; Hangyo, Masanori

    2014-05-01

    Microstructures in nature are ultrafine and ordered in biological roles, which have attracted material scientists. Spirulina forms three-dimensional helical microstructure, one of remarkable features in nature beyond our current processing technology such as lithography in terms of mass-productivity and structural multiplicity. Spirulina varies its diameter, helical pitch, and/or length against growing environment. This unique helix is suggestive of a tiny electromagnetic coil, if composed of electro-conductive metal, which brought us main concept of this work. Here, we describe the biotemplating process onto Spirulina surface to fabricate metal microcoils. Structural parameters of the microcoil can be controlled by the cultivation conditions of Spirulina template and also purely one-handed microcoil can be fabricated. A microcoil dispersion sheet exhibited optically active response attributed to structural resonance in terahertz-wave region.

  9. Wall Painting Investigation by Means of Non-invasive Terahertz Time-Domain Imaging (THz-TDI): Inspection of Subsurface Structures Buried in Historical Plasters

    Science.gov (United States)

    Dandolo, Corinna Ludovica Koch; Jepsen, Peter Uhd

    2016-02-01

    Characterization of subsurface features of wall paintings is important in conservation and technical art history as well as in building archaeology and architecture fields. In this study, an area of the apsidal wall painting of Nebbelunde Church (Rødby, Denmark) has been investigated by means of terahertz time-domain imaging (THz-TDI). Subsurface structures have been detected at different depths inside the lime-based plaster of the wall painting until approximately 1 cm from the surface. The surface morphology of the buried structures has been 3D imaged in detail, providing a substantial contribution in their characterization.

  10. Design and analysis of a lightweight prestressed antenna back-up structure

    Science.gov (United States)

    Ma, Zengxiang; Yang, Dehua; Cheng, Jingquan

    2010-07-01

    The planned Square Kilometer Array (SKA) includes three thousand 15m antennas. The radio flux density from the sun is stronger, so that a solar array, such as Frequency-Agile Solar Radiotelescope (FASR) with hundreds of dishes can have smaller dish size. Therefore, light weight, low cost dish design is of vital importance. The reflecting surface supported by an antenna back-up structure, generally, should have an RMS surface error less than λ/20 (λ. is the operating wavelength). For resisting gravitational, wind, and ice-snow loadings, an antenna dish also requires reasonable mode frequencies. In this paper, different low cost small or medium back-up structure designs are discussed, including double-layer truss design and prestressed dish design. Based on discussion, an innovative light weight, prestressed back-up structure is proposed for small or medium aperture antennas. Example of a small 4.5m aperture dish design working below 3GHz is presented. This design is a one-layer prestressed truss structure with low weight, ease installation, and low manufacture cost. Structural analysis and modal extraction results show the structure is much stiffer than the same structure without prestressed loading.

  11. Harmonic Suppressed Slot Antennas Using Rectangular/Circular Defected Ground Structures

    Directory of Open Access Journals (Sweden)

    Mohammad Saeid Ghaffarian

    2012-01-01

    Full Text Available Two wide rectangle-shaped microstrip-fed 2.6-GHz slot antennas using defected ground structures (DGSs with a low design complexity are proposed to achieve wideband harmonic suppression. To accomplish this, two rectangular DGSs (RDGSs in the first antenna and two circular DGSs (CDGSs in the second one with various dimensions are etched into the ground plane, which could have a wideband-stop characteristic. Simulated and measured reflection coefficients indicate that the two proposed structures effectively suppress the second and third harmonics up to 23 dB between 3.5 and 10.5 GHz with a maximum ripple of 2.4 dB. In addition, the radiation patterns and peak gains of the antennas can be suppressed at least 17 dB and 7.1 dBi, respectively, at the third harmonic frequency of 7.86 GHz.

  12. Room temperature strong light-matter coupling in 3D THz meta-atoms (Conference Presentation)

    Science.gov (United States)

    Paulillo, Bruno; Manceau, Jean-Michel; Li, Lianhe; Linfield, Edmund; Colombelli, Raffaele

    2016-04-01

    We demonstrate strong light-matter coupling at room temperature in the terahertz (THz) spectral region using 3D meta-atoms with extremely sub-wavelength volumes. Using an air-bridge fabrication scheme, we have implemented sub-wavelength 3D THz micro-resonators that rely on suspended loop antennas connected to semiconductor-filled patch cavities. We have experimentally shown that they possess the functionalities of lumped LC resonators: their frequency response can be adjusted by independently tuning the inductance associated the antenna element or the capacitance provided by the metal-semiconductor-metal cavity. Moreover, the radiation coupling and efficiency can be engineered acting on the design of the loop antenna, similarly to conventional RF antennas. Here we take advantage of this rich playground in the context of cavity electrodynamics/intersubband polaritonics. In the strong light-matter coupling regime, a cavity and a two-level system exchange energy coherently at a characteristic rate called the vacuum Rabi frequency ΩR which is dominant with respect to all other loss mechanisms involved. The signature, in the frequency domain, is the appearance of a splitting between the bare cavity and material system resonances: the new states are called upper and a lower polariton branches. So far, most experimental demonstrations of strong light-matter interaction between an intersubband transition and a deeply sub-wavelength mode in the THz or mid-infrared ranges rely on wavelength-scale or larger resonators such as photonic crystals, diffractive gratings, dielectric micro-cavities or patch cavities. Lately, planar metamaterials have been used to enhance the light-matter interaction and strongly reduce the interaction volume by engineering the electric and magnetic resonances of the individual subwavelength constituents. In this contribution we provide evidence of strong coupling between a THz intersubband transition and an extremely sub-wavelength mode (≈λ/10

  13. Structural Stability Assessment of the High Frequency Antenna for Use on the Buccaneer CubeSat in Low Earth Orbit

    Science.gov (United States)

    2014-05-01

    UNCLASSIFIED UNCLASSIFIED Structural Stability Assessment of the High Frequency Antenna for Use on the Buccaneer CubeSat in Low Earth...DSTO-TN-1295 ABSTRACT The Buccaneer CubeSat will be fitted with a high frequency antenna made from spring steel measuring tape. The geometry...High Frequency Antenna for Use on the Buccaneer CubeSat in Low Earth Orbit Executive Summary The Buccaneer CubeSat will be fitted with a

  14. Fractal THz metamaterials

    DEFF Research Database (Denmark)

    Malureanu, Radu; Jepsen, Peter Uhd; Xiao, S.

    2010-01-01

    applications. THz radiation can be employed for various purposes, among them the study of vibrations in biological molecules, motion of electrons in semiconductors and propagation of acoustic shock waves in crystals. We propose here a new THz fractal MTM design that shows very high transmission in the desired...... frequency range as well as a clear differentiation between one polarisation and another. Based on theoretical predictions we fabricated and measured a fractal based THz metamaterial that shows more than 60% field transmission at around 1THz for TE polarized light while the TM waves have almost 80% field...... transmission peak at 0.6THz. One of the main characteristics of this design is its tunability by design: by simply changing the length of the fractal elements one can choose the operating frequency window. The modelling, fabrication and characterisation results will be presented in this paper. Due to the long...

  15. Effect of Slot Antenna Structure on Production of Planar Surface Wave Plasmas

    Science.gov (United States)

    Nagatsu, M.; Ito, A.; Morita, S.; Ghanashev, I.; Sugai, H.; Toyoda, N.

    1998-10-01

    Characteristics of planar surface wave plasmas (SWP) produced by a 2.45 GHz microwave via slot antennas have been studied(M. Nagatsu et al Plasma Sources Sci. Technol.) 6 (1997) 427.^,(H. Sugai et al Plasma Sources Sci. Technol.) 7 (1998) 192.. Effect of antenna-plasma coupling was investigated for various slot antennas by measuring plasma characteristics against an incident microwave power. Four types of slot antenna, that is, inclined, vertical, transverse and radial slots, were tested. At high pressure of say 1 Torr, optical emission patterns of various TM modes were observed in respective slots as expected by theoretical dispersion relationsfootnote I. Ghanashev et al Jpn. J. Appl. Phys. 36 (1997) 337.. At low pressure of 10 mTorr, uniformly broadened plasma emission was observed regardless of the antenna structure. An attempt of reducing dielectric window area for vacuum sealing has been made to develop economical etching or CVD plasma sources with less impurities(S. Morita et al Jpn. J. Appl. Phys.) 37 (1998) L468.. Recent results of SWP experiments in a larger chamber using 2.45 GHz and 915 MHz waves will be also given. This work was supported by Toshiba Corp., Nissin Inc, and also by a Grant-in-Aid for Science Research from the Ministry of Education, Science, Sports and Culture in Japan.

  16. Auxetic shape memory alloy cellular structures for deployable satellite antennas: design, manufacture and testing

    Directory of Open Access Journals (Sweden)

    Di Maio D.

    2010-06-01

    Full Text Available We describe the production development and experimental tests related to an hybrid honeycomb-truss made of shape memory alloy (Ni48Ti46Cu6, and used as a demonstrator for a deployable antenna in deep-space missions. Specific emphasis is placed on the modal analysis techniques used to test the lightweight SMA structure.

  17. Deep x-ray lithography processing for batch fabrication of thick polymer-based antenna structures

    Science.gov (United States)

    Rashidian, Atabak; Klymyshyn, David M.; Boerner, Martin; Mohr, Jürgen

    2010-02-01

    Deep x-ray lithography is applied for the first time to fabricate polymer-based antenna structures with different portions of ceramic contents. To produce successful and viable antenna structures, three different methods are proposed using positive and negative tone resists. In the first method the structures are lithographically fabricated avoiding an intermediate molding step using SU-8 as a photosensitive resist filled with fine ceramic powder with particles in the submicron range. In the second and third methods a polymethylmethacrylate (PMMA) mold is first fabricated by x-ray lithography, and then SU-8/MMA mixed with the high ceramic powder content is injected into the mold. In these methods a final step of crosslinking for SU-8 and polymerization for MMA is also required. Optimized fabrication parameters allow the production of high quality antenna structures as thick as 2.3 mm. X-ray lithography capabilities in fabrication of antennas and other passive microwave components with special features reinforce the idea of fabricating integrated passive microwave circuits along with active circuits using this emerging technology.

  18. Utilizing wideband AMC structures for high-gain inkjet-printed antennas on lossy paper substrate

    KAUST Repository

    Cook, Benjamin Stassen

    2013-01-01

    Significant gain and bandwidth improvement of inkjet-printed antennas with integrated artificial magnetic conductor (AMC) is achieved by utilizing wideband ground-backed frequency selective surfaces (FSSs) to overcome the high losses of organic substrates such as paper. A microstrip-fed monopole mounted on an artificial magnetic conductor is demonstrated to improve the gain by 5 dB over previous works and exhibit much wider impedance bandwidth while maintaining a thin antenna profile and a 20% electrical size reduction. The effect of AMC bandwidth on substrate losses and the gain reduction caused by finite AMC array effects are investigated in an effort to produce high-gain, miniaturized, low-cost wearable and structure mount antennas. © 2013 IEEE.

  19. Structural and evolutionary aspects of antenna chromophore usage by class II photolyases.

    Science.gov (United States)

    Kiontke, Stephan; Gnau, Petra; Haselsberger, Reinhard; Batschauer, Alfred; Essen, Lars-Oliver

    2014-07-11

    Light-harvesting and resonance energy transfer to the catalytic FAD cofactor are key roles for the antenna chromophores of light-driven DNA photolyases, which remove UV-induced DNA lesions. So far, five chemically diverse chromophores have been described for several photolyases and related cryptochromes, but no correlation between phylogeny and used antenna has been found. Despite a common protein topology, structural analysis of the distantly related class II photolyase from the archaeon Methanosarcina mazei (MmCPDII) as well as plantal orthologues indicated several differences in terms of DNA and FAD binding and electron transfer pathways. For MmCPDII we identify 8-hydroxydeazaflavin (8-HDF) as cognate antenna by in vitro and in vivo reconstitution, whereas the higher plant class II photolyase from Arabidopsis thaliana fails to bind any of the known chromophores. According to the 1.9 Å structure of the MmCPDII·8-HDF complex, its antenna binding site differs from other members of the photolyase-cryptochrome superfamily by an antenna loop that changes its conformation by 12 Å upon 8-HDF binding. Additionally, so-called N- and C-motifs contribute as conserved elements to the binding of deprotonated 8-HDF and allow predicting 8-HDF binding for most of the class II photolyases in the whole phylome. The 8-HDF antenna is used throughout the viridiplantae ranging from green microalgae to bryophyta and pteridophyta, i.e. mosses and ferns, but interestingly not in higher plants. Overall, we suggest that 8-hydroxydeazaflavin is a crucial factor for the survival of most higher eukaryotes which depend on class II photolyases to struggle with the genotoxic effects of solar UV exposure. © 2014 by The American Society for Biochemistry and Molecular Biology, Inc.

  20. THz characterization of hydrated and anhydrous materials

    Science.gov (United States)

    Sokolnikov, Andre

    2011-06-01

    The characterization of anhydrous and hydrated forms of materials is of great importance to science and industry. Water content poses difficulties for successful identification of the material structure by THz radiation. However, biological tissues and hydrated forms of nonorganic substances still may be investigated by THz radiation. This paper outlines the range of possibilities of the above characterization, as well as provides analysis of the physical mechanism that allows or prevents penetration of THz waves through the substance. THz-TDS is used to measure the parameters of the characterization of anhydrous and hydrated forms of organic and nonorganic samples. Mathematical methods (such as prediction models of time-series analysis) are used to help identifying the absorption coefficient and other parameters of interest. The discovered dependencies allow designing techniques for material identification/characterization (e.g. of drugs, explosives, etc. that may have water content). The results are provided.

  1. 65 nm CMOS Monolithically Integrated sub-THz transmitter

    NARCIS (Netherlands)

    Hu, X.; Tripodi, L.; Matters-Kammerer, M.K.; Cheng, S.; Rydberg, A.

    2011-01-01

    This letter presents a transmitter for sub-THz radiation (up to 160GHz), which consists of a nonlinear transmission line (NLTL) and anextremely wideband (EWB) slot antenna on a silicon substrate of lowresistivity (10 Ohms•cm). The fabrication was realized using a commercially available 65 nm CMOS

  2. Design and fabrication of two probes for Near Field THz imaging .

    Science.gov (United States)

    Garcia, Angelica; Paz, Gaudencio; Perez, Joel; Qureshi, Naser; Microwave photonics Team

    THz imaging has gained attention due to the potential applications in medicine, security, inspections on semiconductor devices, etc. Until now, systems devoted to Near Field THz imaging consist of two basic parts: generation of THz radiation and a sensing probe system. In this work we present two approaches to make a probe for near field THz imaging. The first one is a novel device capable of integrate in a single chip the THz source with the sensing system. The device is fabricated in a GaAs substrate, on one side a photoconductive gold antenna is printed using microfabrication techniques; on the opposite side a specifically designed bow tie sub-wavelength sized bow-tie aperture is placed centered to the gap of the antenna. According to our simulations, the aperture exhibits field enhancement at the metal tips when it is illuminated from the substrate side by the THz radiation emitted from the antenna. The second device is a tapered conical waveguide with micrometrical aperture size at the end. A commercial silicon lens is used to focus the THz radiation emitted from a photoconductive antenna on the aperture. Simulation in COMSOL is used to find the best taper angle where reflection and loss are reduced. PAPIIT 106316 and CONACYT Fronteras 344.

  3. Atmospheric propagation of THz radiation.

    Energy Technology Data Exchange (ETDEWEB)

    Wanke, Michael Clement; Mangan, Michael A.; Foltynowicz, Robert J.

    2005-11-01

    In this investigation, we conduct a literature study of the best experimental and theoretical data available for thin and thick atmospheres on THz radiation propagation from 0.1 to 10 THz. We determined that for thick atmospheres no data exists beyond 450 GHz. For thin atmospheres data exists from 0.35 to 1.2 THz. We were successful in using FASE code with the HITRAN database to simulate the THz transmission spectrum for Mauna Kea from 0.1 to 2 THz. Lastly, we successfully measured the THz transmission spectra of laboratory atmospheres at relative humidities of 18 and 27%. In general, we found that an increase in the water content of the atmosphere led to a decrease in the THz transmission. We identified two potential windows in an Albuquerque atmosphere for THz propagation which were the regions from 1.2 to 1.4 THz and 1.4 to 1.6 THz.

  4. Conformal load-bearing antenna structures (CLAS): initiative for multiple military and commercial applications

    Science.gov (United States)

    Lockyer, Allen J.; Alt, Kevin H.; Kudva, Jayanth N.; Kinslow, Robert W.; Goetz, Allan C.

    1997-06-01

    The Structures Division of the Air Force's Wright Laboratory is sponsoring the development and demonstration of a new high pay-off technology termed CLAS--Conformal Load Bearing Antenna Structures. Northrop Grumman Corporation and TRW/ASD are developing the technology under the `Smart-Skin Structure Technology Demonstration (S3D)' program, contract, No. F33615-93-C-3200. The program goal is to design, develop, fabricate, and test a CLAS component and lay the foundation for future work where potential benefits from structurally integrated antennas may be realized. Key issues will focus but are not limited to the design, structures, and manufacturing aspects of antenna embedment into load bearing aircraft structures. Results from Phase 1 of the program have been previously reported, where initial pay-offs in reducing overall airframe acquisition and support cost, weight, signature, and drag were quantitatively and qualitatively identified. A full-sized CLAS component, featuring a broadband multi-arm spiral embedded in sandwich stiffened structure, will be fabricated and tested for static strength, durability, and damage tolerance. Basic electrical performance, (e.g., radiation patterns, gain, and impedance) will also be verified; however, extensive electrical validation will be the subject of further work. Key aspects of the work and progress to date are detailed below. Also covered are future projections of CLAS technology expansion beyond tactical aircraft into other military products highlighting ships, army vehicles, and `spin-off' commercial applications to civil aircraft and the automotive industry.

  5. Optical antenna enhanced spontaneous emission.

    Science.gov (United States)

    Eggleston, Michael S; Messer, Kevin; Zhang, Liming; Yablonovitch, Eli; Wu, Ming C

    2015-02-10

    Atoms and molecules are too small to act as efficient antennas for their own emission wavelengths. By providing an external optical antenna, the balance can be shifted; spontaneous emission could become faster than stimulated emission, which is handicapped by practically achievable pump intensities. In our experiments, InGaAsP nanorods emitting at ∼ 200 THz optical frequency show a spontaneous emission intensity enhancement of 35 × corresponding to a spontaneous emission rate speedup ∼ 115 ×, for antenna gap spacing, d = 40 nm. Classical antenna theory predicts ∼ 2,500 × spontaneous emission speedup at d ∼ 10 nm, proportional to 1/d(2). Unfortunately, at d antenna efficiency drops below 50%, owing to optical spreading resistance, exacerbated by the anomalous skin effect (electron surface collisions). Quantum dipole oscillations in the emitter excited state produce an optical ac equivalent circuit current, I(o) = qω|x(o)|/d, feeding the antenna-enhanced spontaneous emission, where q|x(o)| is the dipole matrix element. Despite the quantum-mechanical origin of the drive current, antenna theory makes no reference to the Purcell effect nor to local density of states models. Moreover, plasmonic effects are minor at 200 THz, producing only a small shift of antenna resonance frequency.

  6. Dual THz comb spectroscopy

    Science.gov (United States)

    Yasui, Takeshi

    2017-08-01

    Optical frequency combs are innovative tools for broadband spectroscopy because a series of comb modes can serve as frequency markers that are traceable to a microwave frequency standard. However, a mode distribution that is too discrete limits the spectral sampling interval to the mode frequency spacing even though individual mode linewidth is sufficiently narrow. Here, using a combination of a spectral interleaving and dual-comb spectroscopy in the terahertz (THz) region, we achieved a spectral sampling interval equal to the mode linewidth rather than the mode spacing. The spectrally interleaved THz comb was realized by sweeping the laser repetition frequency and interleaving additional frequency marks. In low-pressure gas spectroscopy, we achieved an improved spectral sampling density of 2.5 MHz and enhanced spectral accuracy of 8.39 × 10-7 in the THz region. The proposed method is a powerful tool for simultaneously achieving high resolution, high accuracy, and broad spectral coverage in THz spectroscopy.

  7. Some Recent Developments of Microstrip Antenna

    Directory of Open Access Journals (Sweden)

    Yong Liu

    2012-01-01

    Full Text Available Although the microstrip antenna has been extensively studied in the past few decades as one of the standard planar antennas, it still has a huge potential for further developments. The paper suggests three areas for further research based on our previous works on microstrip antenna elements and arrays. One is exploring the variety of microstrip antenna topologies to meet the desired requirement such as ultrawide band (UWB, high gain, miniaturization, circular polarization, multipolarized, and so on. Another is to apply microstrip antenna to form composite antenna which is more potent than the individual antenna. The last is growing towards highly integration of antenna/array and feeding network or operating at relatively high frequencies, like sub-millimeter wave or terahertz (THz wave regime, by using the advanced machining techniques. To support our points of view, some examples of antennas developed in our group are presented and discussed.

  8. Dual Band-Notched Microstrip-Fed Vivaldi Antenna Utilizing Compact EBG Structures

    Directory of Open Access Journals (Sweden)

    K. A. Alshamaileh

    2015-01-01

    Full Text Available We propose an ultra-wideband (UWB antipodal Vivaldi antenna (AVA with high-Q stopband characteristics based on compact electromagnetic bandgap (EBG structures. First, an AVA is designed and optimized to operate over an UWB spectrum. Then, two pairs of EBG cells are introduced along the antenna feed line to suppress the frequency components at 3.6–3.9 and 5.6–5.8 GHz (i.e., WiMAX and ISM bands, resp.. Simulated and measured results show a voltage standing wave ratio (VSWR below 2 for the entire 3.1–10.6 GHz band with high attenuation at the two selected subbands. This simple yet effective approach eliminates the need to deform the antenna radiators with slots/parasitic elements or comprise multilayer substrates. Furthermore, the flexibility it offers in terms of controlling both the number and locations of the band-reject frequencies is advantageous for antennas with nonuniform flares as in the AVA.

  9. Nondimensional characterization and asymptotic model development for multifunctional structures with application to load-bearing antennas

    International Nuclear Information System (INIS)

    Santapuri, Sushma; Bechtel, Stephen E

    2014-01-01

    This paper (i) presents a mathematical approach to formulate leading-order models for complex multifunctional systems with coupled thermomechanical and electromagnetic field interactions, and (ii) demonstrates its applicability to the modeling and analysis of a load-bearing antenna, a multifunctional sensing and transmitting device integrated with a load-bearing structure. Starting from first-principle equations, i.e. the thermomechanical balance laws coupled with Maxwell’s equations, nondimensionalization and perturbation techniques are employed to formulate a leading-order model for the coupled system. Depending on the design of the structure and nature of the excitation, the nondimensional numbers arising in the coupled multifunctional system are quantified, and through a relative ordering of these quantities, the dominant physical effects are extracted. The resulting dominant effects determine the regime of operation of the structure, and in turn dictate the appropriate computational model. This approach is demonstrated through an application to a load-bearing antenna for a prototypical design. The resulting leading-order model is subsequently solved, and the electrical and structural response of the load-bearing antenna is analyzed and compared for different combinations of material properties. The framework introduced in this paper is envisioned to have applications in developing leading-order models for a wide range of complex multifunctional systems and can be utilized for their efficient design. (paper)

  10. Effect of soil-structure interaction on the seismic behaviour of pedestal-structure system in large dish antennas

    Directory of Open Access Journals (Sweden)

    Bahador Pourhatami

    2017-12-01

    Full Text Available Regarding the progressive improvement in the territory of Space Technology in all developed countries and consequently developing countries including Islamic Republic of Iran, the optimization of design and utilization of the communication equipment has been paid more attention today. For instance, considering recent highly innovative methods, specifically in communication field, developed for design, manufacturing and exploiting dish antenna for specific cases, cooperation of other science and technology experts, like civil engineers, is also necessary. In this way, more delicate design procedure in order to satisfy communication requirement, is achieved. So far, no specific investigation about aforementioned subject, especially the effect of soil-structure interaction (SSI in analysing the seismic behaviour of communication large dish antennas has been conducted in Iran. In this paper, with the aim of investigating the effect of SSI on seismic behavior of pedestal, first an acceptable range for antenna displacement – as the most important parameter in pedestal structure for antenna – in both operational and survival states, has been calculated numerically based on generic formula. Secondly, the modelling of the whole pedestal-structure system has been modelled subjected to the associated loads and other primary conditions. This procedure has been performed once without considering the SSI and once more with it. Comparison of the obtained results shows that considering the SSI would impress the output results with a difference rate more than 50% and 600% respectively at survival and operational condition.

  11. Effect of photonic crystal and frequency selective surface implementation on gain enhancement in the microstrip patch antenna at terahertz frequency

    Science.gov (United States)

    Nejati, Ameneh; Sadeghzadeh, Ramezan Ali; Geran, Fatemeh

    2014-09-01

    In this paper, microstrip patch antenna with frequency selective surface (FSS) and photonic band gap (PBG) structures in the frequency range of 0.5-0.7 THz is presented for wireless communications. Proposed patch antenna is designed on a substrate with uniform and non-uniform PBG structures. Here, the effects of substrate thickness, various radii and arrangement of holes on antenna resonance in both PBG forms are studied. Near zero characteristic on uniform and non-uniform PBG substrate is compared and the results show that along with increase in hole radius, antenna operating frequency and bandwidth are increased. Also, the FSS structure is designed as a perfect absorber. Finally, by using FSS and PBG structures simultaneously, gain enhancement, increase in directivity and pattern shaping are studied at THz field. The antenna gain in final structure is increased by 2 dBi (32%) in comparison to simple form and Half-Power beam width is reduced from 100°×80° in simple form to 72°×48° by using FSS and PBG. All simulations and designs are done by Ansoft HFSS and CST Microwave Studio simulation tools with different full wave methods.

  12. Introduction to THz wave photonics

    CERN Document Server

    Zhang, X-C

    2009-01-01

    Introduction to THz Wave Photonics examines the science and technology related to terahertz wave technologies, taking a dual approach between presenting the field 's history while simultaneously providing an overview of existing technology. The latest research in developing THz areas such as electromagnetic waves are presented, along with an introduction to continuous wave THz technology. Authors X.-C. Zhang and Jingzhou Xu place particular emphasis on pulsed THz technology, among many other facets of THz technology including: Complete coverage of THz wave spectroscopy and imagingA discussion

  13. A 2×1 Coplanar Monopole Antenna Structure for Wireless RF Energy Harvesting

    Science.gov (United States)

    Mathur, Monika; Agarwal, Ankit; Singh, Ghanshyam; Bhatnagar, S. K.

    2018-03-01

    The objective of this paper is to design an efcient wireless energy harvesting (WEH) system to eliminate the problem to continuous charging of a battery operated electronics devices. Most of the devices are battery operated so charging of a battery time to time is serious issue. This WEH system receives the Radio Frequency (RF) and Microwave frequency signals present in the atmosphere and converting it into DC signal so that it can stores in Capacitor or charges a battery for utilize the power. For this RF energy harvesting purposes 21 antenna array structure of the coplanar monopole antenna is presented. This structure shows the gain of 10.2 dBi and 83% efciency. This structure is designed for resonating on multiple bands (Radio, GSM, ISM, and UWB). It is useful for this application because it covers almost all useful bands in the maximum capturing area. The antenna can be connected directly to an RF-DC converter module and it uses about 60% of the total PCB area. And RF to DC convertor circuit can be implemented in that remaining 40% area on the same substrate so it eliminates the need of port connectors and impedance matching circuit between them. This design is worked in receiving mode only when used for energy harvesting purposes. This may be useful for the biomedical and satellite applications.

  14. Quantitative study of rectangular waveguide behavior in the THz.

    Energy Technology Data Exchange (ETDEWEB)

    Rowen, Adam M.; Nordquist, Christopher Daniel; Wanke, Michael Clement

    2009-10-01

    This report describes our efforts to quantify the behavior of micro-fabricated THz rectangular waveguides on a configurable, robust semiconductor-based platform. These waveguides are an enabling technology for coupling THz radiation directly from or to lasers, mixers, detectors, antennas, and other devices. Traditional waveguides fabricated on semiconductor platforms such as dielectric guides in the infrared or co-planar waveguides in the microwave regions, suffer high absorption and radiative losses in the THz. The former leads to very short propagation lengths, while the latter will lead to unwanted radiation modes and/or crosstalk in integrated devices. This project exploited the initial developments of THz micro-machined rectangular waveguides developed under the THz Grand Challenge Program, but instead of focusing on THz transceiver integration, this project focused on exploring the propagation loss and far-field radiation patterns of the waveguides. During the 9 month duration of this project we were able to reproduce the waveguide loss per unit of length in the waveguides and started to explore how the loss depended on wavelength. We also explored the far-field beam patterns emitted by H-plane horn antennas attached to the waveguides. In the process we learned that the method of measuring the beam patterns has a significant impact on what is actually measured, and this may have an effect on most of the beam patterns of THz that have been reported to date. The beam pattern measurements improved significantly throughout the project, but more refinements of the measurement are required before a definitive determination of the beam-pattern can be made.

  15. Slotted Waveguide Antenna Stiffened Structures (SWASS) Development for Commercial Off-the-Shelf (COTS) Radar (Briefing Charts)

    Science.gov (United States)

    2016-10-01

    AFRL-RQ-WP-TM-2016-0150 SLOTTED WAVEGUIDE ANTENNA STIFFENED STRUCTURES (SWASS) DEVELOPMENT FOR COMMERCIAL OFF-THE-SHELF (COTS) RADAR...WAVEGUIDE ANTENNA STIFFENED STRUCTURES (SWASS) DEVELOPMENT FOR COMMERCIAL OFF-THE-SHELF (COTS) RADAR (BRIEFING CHARTS) 5a. CONTRACT NUMBER In-house 5b...0896) 1. http://www.uasvision.com/2012/06/15/imsar-gets-24m-nano-sar-contract-for-uas-from-us-army/ 2. http://www.barnardmicrosystems.com/ UAV /features

  16. Design of UWB Monopole Antenna with Dual Notched Bands Using One Modified Electromagnetic-Bandgap Structure

    Directory of Open Access Journals (Sweden)

    Hao Liu

    2013-01-01

    Full Text Available A modified electromagnetic-bandgap (M-EBG structure and its application to planar monopole ultra-wideband (UWB antenna are presented. The proposed M-EBG which comprises two strip patch and an edge-located via can perform dual notched bands. By properly designing and placing strip patch near the feedline, the proposed M-EBG not only possesses a simple structure and compact size but also exhibits good band rejection. Moreover, it is easy to tune the dual notched bands by altering the dimensions of the M-EBG. A demonstration antenna with dual band-notched characteristics is designed and fabricated to validate the proposed method. The results show that the proposed antenna can satisfy the requirements of VSWR < 2 over UWB 3.1–10.6 GHz, except for the rejected bands of the world interoperability for microwave access (WiMAX and the wireless local area network (WLAN at 3.5 GHz and 5.5 GHz, respectively.

  17. Design of UWB monopole antenna with dual notched bands using one modified electromagnetic-bandgap structure.

    Science.gov (United States)

    Liu, Hao; Xu, Ziqiang

    2013-01-01

    A modified electromagnetic-bandgap (M-EBG) structure and its application to planar monopole ultra-wideband (UWB) antenna are presented. The proposed M-EBG which comprises two strip patch and an edge-located via can perform dual notched bands. By properly designing and placing strip patch near the feedline, the proposed M-EBG not only possesses a simple structure and compact size but also exhibits good band rejection. Moreover, it is easy to tune the dual notched bands by altering the dimensions of the M-EBG. A demonstration antenna with dual band-notched characteristics is designed and fabricated to validate the proposed method. The results show that the proposed antenna can satisfy the requirements of VSWR UWB 3.1-10.6 GHz, except for the rejected bands of the world interoperability for microwave access (WiMAX) and the wireless local area network (WLAN) at 3.5 GHz and 5.5 GHz, respectively.

  18. Josephson emission with frequency span 1-11 THz from small Bi2Sr2CaCu2O8+δmesa structures.

    Science.gov (United States)

    Borodianskyi, E A; Krasnov, V M

    2017-11-23

    Mesa structures made of Bi 2 Sr 2 CaCu 2 O 8+δ high-temperature superconductor represent stacks of atomic scale intrinsic Josephson junctions. They can be used for generation of high-frequency electromagnetic waves. Here we analyze Josephson emission from small-but-high mesas (with a small area, but containing many stacked junctions). We have found strong evidence for tunable terahertz emission with a good efficacy in a record high-frequency span 1-11 THz, approaching the theoretical upper limit for this superconductor. Emission maxima correspond to in-phase cavity modes in the mesas, indicating coherent superradiant nature of the emission. We conclude that terahertz emission requires a threshold number of junctions N ~ 100. The threshold behavior is not present in the classical description of stacked Josephson junctions and suggests importance of laser-like cascade amplification of the photon number in the cavity.

  19. THz characterization and demonstration of visible-transparent/terahertz-functional electromagnetic structures in ultra-conductive La-doped BaSnO3Films.

    Science.gov (United States)

    Arezoomandan, Sara; Prakash, Abhinav; Chanana, Ashish; Yue, Jin; Mao, Jieying; Blair, Steve; Nahata, Ajay; Jalan, Bharat; Sensale-Rodriguez, Berardi

    2018-02-23

    We report on terahertz characterization of La-doped BaSnO 3 (BSO) thin-films. BSO is a transparent complex oxide material, which has attracted substantial interest due to its large electrical conductivity and wide bandgap. The complex refractive index of these films is extracted in the 0.3 to 1.5 THz frequency range, which shows a metal-like response across this broad frequency window. The large optical conductivity found in these films at terahertz wavelengths makes this material an interesting platform for developing electromagnetic structures having a strong response at terahertz wavelengths, i.e. terahertz-functional, while being transparent at visible and near-IR wavelengths. As an example of such application, we demonstrate a visible-transparent terahertz polarizer.

  20. THE HYPERFINE STRUCTURE OF THE ROTATIONAL SPECTRUM OF HDO AND ITS EXTENSION TO THE THz REGION: ACCURATE REST FREQUENCIES AND SPECTROSCOPIC PARAMETERS FOR ASTROPHYSICAL OBSERVATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Cazzoli, Gabriele; Lattanzi, Valerio; Puzzarini, Cristina [Dipartimento di Chimica “Giacomo Ciamician”, Università di Bologna, Via Selmi 2, I-40126 Bologna (Italy); Alonso, José Luis [Grupo de Espectroscopía Molecular (GEM), Unidad Asociada CSIC, Edificio Quifima, Laboratorios de Espectroscopia y Bioespectroscopia, Parque Científico UVa, Universidad de Valladolid, E-47005 Valladolid (Spain); Gauss, Jürgen, E-mail: cristina.puzzarini@unibo.it [Institut für Physikalische Chemie, Universität Mainz, D-55099 Mainz (Germany)

    2015-06-10

    The rotational spectrum of the mono-deuterated isotopologue of water, HD{sup 16}O, has been investigated in the millimeter- and submillimeter-wave frequency regions, up to 1.6 THz. The Lamb-dip technique has been exploited to obtain sub-Doppler resolution and to resolve the hyperfine (hf) structure due to the deuterium and hydrogen nuclei, thus enabling the accurate determination of the corresponding hf parameters. Their experimental determination has been supported by high-level quantum-chemical calculations. The Lamb-dip measurements have been supplemented by Doppler-limited measurements (weak high-J and high-frequency transitions) in order to extend the predictive capability of the available spectroscopic constants. The possibility of resolving hf splittings in astronomical spectra has been discussed.

  1. Graphene-Enhanced Metamaterials for THz Applications

    DEFF Research Database (Denmark)

    Andryieuski, Andrei; Khromova, Irina; Zhukovsky, Sergei

    2016-01-01

    manipulate electromagnetic waves. The possibilities of light manipulation can be extended even more by involving new active materials as a structural component – such as, for example, graphene. Its prominent conductivity tunability through the electrochemical potential change allows converting a multilayer...... graphene/dielectric structure into an artificial medium with widely varying properties – transparent or opaque, plasmonic, low-index or high-index dielectric – in a certain THz or infra-red frequency range. This chapter presents several examples of effective THz components like absorbers, modulators......, and filters based on graphene-dielectric multilayers...

  2. Probing giant magnetoresistance with THz spectroscopy

    DEFF Research Database (Denmark)

    Jin, Zuanming; Tkach, Alexander; Casper, Frederick

    2014-01-01

    We observe a giant magnetoresistance effect in CoFe/Cu-based multistack using THz time-domain spectroscopy. The magnetic field-dependent dc conductivity, electron scattering time, as well as spin-asymmetry parameter of the structure are successfully determined. © 2014 OSA.......We observe a giant magnetoresistance effect in CoFe/Cu-based multistack using THz time-domain spectroscopy. The magnetic field-dependent dc conductivity, electron scattering time, as well as spin-asymmetry parameter of the structure are successfully determined. © 2014 OSA....

  3. Two-Element Tapered Slot Antenna Array for Terahertz Resonant Tunneling Diode Oscillators

    Directory of Open Access Journals (Sweden)

    Jianxiong Li

    2014-01-01

    Full Text Available Two-element tapered slot antenna (TSA array for terahertz (THz resonant tunneling diode (RTD oscillators is proposed in this paper. The proposed TSA array has the advantages of both the high directivity and high gain at the horizontal direction and hence can facilitate the horizontal communication between the RTD oscillators and other integrated circuit chips. A MIM (metal-insulator-metal stub with a T-shaped slot is used to reduce the mutual coupling between the TSA elements. The validity and feasibility of the proposed TSA array have been simulated and analyzed by the ANSYS/ANSOFT’s High Frequency Structure Simulator (HFSS. Detailed modeling approaches and theoretical analysis of the proposed TSA array have been fully addressed. The simulation results show that the mutual coupling between the TSA elements is reduced below −40 dB. Furthermore, at 500 GHz, the directivity, the gain, and the half power beam width (HPBW at the E-plane of the proposed TSA array are 12.18 dB, 13.09 dB, and 61°, respectively. The proposed analytical method and achieved performance are very promising for the antenna array integrated with the RTD oscillators at the THz frequency and could pave the way to the design of the THz antenna array for the RTD oscillators.

  4. A Microbolometer System for Radiation Detection in the THz Frequency Range with a Resonating Cavity Fabricated in the CMOS Technology.

    Science.gov (United States)

    Sesek, Aleksander; Zemva, Andrej; Trontelj, Janez

    2018-02-14

    The THz sensors using microbolometers as a sensing element are reported as one of the most sensitive room-temperature THz detectors suitable for THz imaging and spectroscopic applications. Microbolometer detectors are usually fabricated using different types of the MEMS technology. The patent for the detection system presented in this paper describes a method for microbolometer fabrication using a standard CMOS technology with advanced micromachining techniques. The measured sensitivity of the sensors fabricated by the patented method is 1000 V/W at an optimal frequency and is determined by the performance of a double-dipole antenna and quarter-wavelength resonant cavity. The paper presents a patented method for fabrication of a microbolometer system for radiation detection in the THz frequency range (16). The method is divided into several stages regarding the current silicon micromachining process. Main stages are fabrication of supporting structures for micro bridge, creation of micro cavities and fabrication of Aluminum antenna and Titanium microbolometer. Additional method for encapsulation in the vacuum is described which additionally improves the performance of bolometer. The CMOS technology is utilized for fabrication as it is cost effective and provides the possibility of larger sensor systems integration with included amplification. At other wavelengths (e.g. IR region) thermistors are usually also the receivers with the sensor resistance change provoked by self-heating. In the THz region the energy is received by an antenna coupled to a thermistor. Depending on the specific application requirement, two types of the antenna were designed and used; a narrow-band dipole antenna and a wideband log-periodic antenna. With method described in the paper, the microbolometer detector reaches sensitivities up to 500 V/W and noise equivalent power (NEP) down to 10 pW/√Hz. Additional encapsulation in the vacuum improves its performance at least by a factor of 2

  5. Non-invasive Florentine Renaissance Panel Painting Replica Structures Investigation by Using Terahertz Time-Domain Imaging (THz-TDI) Technique

    DEFF Research Database (Denmark)

    Dandolo, Corinna Ludovica Koch; Picollo, Marcello; Cucci, Costanza

    2016-01-01

    The potentials of the Terahertz Time-Domain Imaging (THz-TDI) technique for a non-invasive inspection of panel paintings have been considered in detail. The THz-TD data acquired on a replica of a panel painting made in imitation of Italian Renaissance panel paintings were processed in order to pr...

  6. THz and Security Applications

    CERN Document Server

    Sizov, Fedir; Detectors, Sources and Associated Electronics for THz Applications

    2014-01-01

    These proceedings comprise invited papers from highly experienced researchers in THz technology and security applications. THz detection of explosives represents one of the most appealing technologies to have recently emerged in dealing with terrorist attacks encountered by civil security and military forces throughout the world. Discussed are the most advanced technologies and developments, the various points of operational strength and weaknesses as well as are suggestions and predictions the best technological solutions to  overcome current operational limits.  The current status of various levels of cooling in THz detectors, sources and associated electronics are also addressed. The goal was to provide a clear view on the current technologies available and the required advances needed in order to achieve more efficient systems. This goal was outlined in part by establishing the baseline of current uncertainty estimations in physics-based modelling and the identification of key areas which require additi...

  7. Passive THz metamaterials

    DEFF Research Database (Denmark)

    Lavrinenko, Andrei; Malureanu, Radu; Zalkovskij, Maksim

    2012-01-01

    In this work we present our activities in the fabrication and characterization of passive THz metamaterials. We use two fabrication processes to develop metamaterials either as free-standing metallic membranes or patterned metallic multi-layers on the substrates to achieve different functionaliti....... Our interest lies in metamaterials for a broad spectrum of linear properties in operations with THz waves, such as linear and circular polarizers, absorbers and devices with enhanced transmittivity, single layer dichroic and chiral systems. All the three steps (modelling, fabrication...

  8. In situ high-resolution structure of the baseplate antenna complex in Chlorobaculum tepidum

    DEFF Research Database (Denmark)

    Nielsen, Jakob Toudahl; Kulminskaya, Natalia V.; Bjerring, Morten

    2016-01-01

    Photosynthetic antenna systems enable organisms harvesting light and transfer the energy to the photosynthetic reaction centre, where the conversion to chemical energy takes place. One of the most complex antenna systems, the chlorosome, found in the photosynthetic green sulfur bacterium...... of highly symmetric oligomeric structures. We show that the baseplate is composed of rods of repeated dimers of the strongly amphipathic CsmA with pigments sandwiched within the dimer at the hydrophobic side of the helix....

  9. Low-loss and bendable THz fiber with tailored dispersion

    DEFF Research Database (Denmark)

    Nielsen, Kristian; Rasmussen, Henrik K.; Adam, Aurèle J. L.

    2009-01-01

    A polymer THz fiber made of Topas and having a Photonic Crystal Fiber structure is demonstrated. It has low broadband loss and the dispersion of the fiber can be tailored by adjusting the structural parameters.......A polymer THz fiber made of Topas and having a Photonic Crystal Fiber structure is demonstrated. It has low broadband loss and the dispersion of the fiber can be tailored by adjusting the structural parameters....

  10. The human skin as a sub-THz receiver - Does 5G pose a danger to it or not?

    Science.gov (United States)

    Betzalel, Noa; Ben Ishai, Paul; Feldman, Yuri

    2018-05-01

    In the interaction of microwave radiation and human beings, the skin is traditionally considered as just an absorbing sponge stratum filled with water. In previous works, we showed that this view is flawed when we demonstrated that the coiled portion of the sweat duct in upper skin layer is regarded as a helical antenna in the sub-THz band. Experimentally we showed that the reflectance of the human skin in the sub-THz region depends on the intensity of perspiration, i.e. sweat duct's conductivity, and correlates with levels of human stress (physical, mental and emotional). Later on, we detected circular dichroism in the reflectance from the skin, a signature of the axial mode of a helical antenna. The full ramifications of what these findings represent in the human condition are still unclear. We also revealed correlation of electrocardiography (ECG) parameters to the sub-THz reflection coefficient of human skin. In a recent work, we developed a unique simulation tool of human skin, taking into account the skin multi-layer structure together with the helical segment of the sweat duct embedded in it. The presence of the sweat duct led to a high specific absorption rate (SAR) of the skin in extremely high frequency band. In this paper, we summarize the physical evidence for this phenomenon and consider its implication for the future exploitation of the electromagnetic spectrum by wireless communication. Starting from July 2016 the US Federal Communications Commission (FCC) has adopted new rules for wireless broadband operations above 24 GHz (5 G). This trend of exploitation is predicted to expand to higher frequencies in the sub-THz region. One must consider the implications of human immersion in the electromagnetic noise, caused by devices working at the very same frequencies as those, to which the sweat duct (as a helical antenna) is most attuned. We are raising a warning flag against the unrestricted use of sub-THz technologies for communication, before the

  11. THz identification and Bayes modeling

    Science.gov (United States)

    Sokolnikov, Andre

    2017-05-01

    THz Identification is a developing technology. Sensing in the THz range potentially gives opportunity for short range radar sensing because THz waves can better penetrate through obscured atmosphere, such as fog, than visible light. The lower scattering of THz as opposed to the visible light results also in significantly better imaging than in IR spectrum. A much higher contrast can be achieved in medical trans-illumination applications than with X-rays or visible light. The same THz radiation qualities produce better tomographical images from hard surfaces, e.g. ceramics. This effect comes from the delay in time of reflected THz pulses detection. For special or commercial applications alike, the industrial quality control of defects is facilitated with a lower cost. The effectiveness of THz wave measurements is increased with computational methods. One of them is Bayes modeling. Examples of this kind of mathematical modeling are considered.

  12. Tunable THz Generation by the Interaction of a Super-luminous Laser Pulse with Biased Semiconductor Plasma

    International Nuclear Information System (INIS)

    Papadopoulos, K.; Zigler, A.

    2006-01-01

    Terahertz (THz) radiation is electromagnetic radiation in the range between several hundred and a few thousand GHz. It covers the gap between fast-wave electronics (millimeter waves) and optics (infrared). This spectral region offers enormous potential for detection of explosives and chemical/biological agents, non-destructive testing of non-metallic structural materials and coatings of aircraft structures, medical imaging, bio-sensing of DNA stretching modes and high-altitude secure communications. The development of these applications has been hindered by the lack of powerful, tunable THz sources with controlled waveform. The need for such sources is accentuated by the strong, but selective absorption of THz radiation during transmission through air with high vapor content. The majority of the current experimental work relies on time-domain spectroscopy using fast electrically biased photoconductive sources in conjunction with femto-second mode-locked Ti:Sapphire lasers. These sources known as Large Aperture Photoconductive Antennas (LAPA) have very limited tunability, relatively low upper bound of power and no bandwidth control. The paper presents a novel source of THz radiation known as Miniature Photoconductive Capacitor Array (MPCA). Experiments demonstrated tunability between .1 - 2 THz, control of the relative bandwidth Δf/f between .5-.01, and controlled pulse length and pulse waveform (temporal shape, chirp, pulse-to-pulse modulation etc.). Direct scaling from the current device indicates efficiency in excess of 30% at 1 THz with 1/f2 scaling at higher frequencies, peak power of 100 kW and average power between .1-1 W. The physics underlying the MPCA is the interaction of a super-luminous ionization front generated by the oblique incidence of a Ti:Sapphire laser pulse on a semiconductor crystal (ZnSe) biased with an alternating electrostatic field, similar to that of a frozen wave generator. It is shown theoretically and experimentally that the

  13. Non-invasive Florentine Renaissance Panel Painting Replica Structures Investigation by Using Terahertz Time-Domain Imaging (THz-TDI) Technique

    Science.gov (United States)

    Koch Dandolo, Corinna L.; Picollo, Marcello; Cucci, Costanza; Jepsen, Peter Uhd

    2016-11-01

    The potentials of the Terahertz Time-Domain Imaging (THz-TDI) technique for a non-invasive inspection of panel paintings have been considered in detail. The THz-TD data acquired on a replica of a panel painting made in imitation of Italian Renaissance panel paintings were processed in order to provide insights as to the limits and potentials of the technique in detecting different kinds of underdrawings and paint layers. Constituent layers, construction techniques, and anomalies were identified and localized by interpreting the extracted THz dielectric stratigraphy.

  14. Probing giant magnetoresistance with THz spectroscopy

    DEFF Research Database (Denmark)

    Jin, Zuanming; Tkach, Alexander; Casper, Frederick

    2014-01-01

    We observe a giant magnetoresistance effect in CoFe/Cu-based multistack using THz time-domain spectroscopy. The magnetic field-dependent dc conductivity, electron scattering time, as well as spin-asymmetry parameter of the structure are successfully determined. © 2014 OSA....

  15. Generalized transmission line method to study the far-zone radiation of antennas under a multilayer structure

    CERN Document Server

    Wu, Xuan Hui

    2008-01-01

    This book gives a step-by-step presentation of a generalized transmission line method to study the far-zone radiation of antennas under a multilayer structure. Normally, a radiation problem requires a full wave analysis which may be time consuming. The beauty of the generalized transmission line method is that it transforms the radiation problem for a specific type of structure, say the multilayer structure excited by an antenna, into a circuit problem that can be efficiently analyzed. Using the Reciprocity Theorem and far-field approximation, the method computes the far-zone radiation due to

  16. Widely tunable THz synthesizer

    Science.gov (United States)

    Hindle, F.; Mouret, G.; Eliet, S.; Guinet, M.; Cuisset, A.; Bocquet, R.; Yasui, T.; Rovera, D.

    2011-09-01

    The generation of cw-THz radiation by photomixing is particularly suited to the high resolution spectroscopy of gases; nevertheless, until recently, it has suffered from a lack of frequency metrology. Frequency combs are a powerful tool that can transfer microwave frequency standards to optical frequencies and a single comb has permitted accurate (10-8) THz frequency synthesis with a limited tuning range. A THz synthesizer composed of three extended cavity laser diodes phase locked to a frequency comb has been constructed and its utility for high resolution gas phase spectroscopy demonstrated. The third laser diode allows a larger tuning range of up to 300 MHz to be achieved without the need for large frequency excursions, while the frequency comb provides a versatile link to be established from any traceable microwave frequency standard. The use of a single frequency comb as a reference for all of the cw-lasers eliminates the dependency of synthesized frequency on the carrier envelope offset frequency. This greatly simplifies the frequency comb stabilization requirements and leads to a reduced instrument complexity.

  17. A Monopole Antenna at Optical Frequencies: Single-Molecule Near-Field Measurements

    NARCIS (Netherlands)

    Taminiau, Tim H.; Segerink, Franciscus B.; van Hulst, N.F.

    2007-01-01

    We present a monopole antenna for optical frequencies (~600 THz) and discuss near-field measurements with single fluorescent molecules as a technique to characterize such antennas. The similarities and differences between near-field antenna measurements at optical and radio frequencies are discussed

  18. Impact of Data Processing and Antenna Frequency on Spatial Structure Modelling of GPR Data.

    Science.gov (United States)

    De Benedetto, Daniela; Quarto, Ruggiero; Castrignanò, Annamaria; Palumbo, Domenico A

    2015-07-08

    Over the last few years high-resolution geophysical techniques, in particular ground-penetrating radar (GPR), have been used in agricultural applications for assessing soil water content variation in a non-invasive way. However, the wide use of GPR is greatly limited by the data processing complexity. In this paper, a quantitative analysis of GPR data is proposed. The data were collected with 250, 600 and 1600 MHz antennas in a gravelly soil located in south-eastern Italy. The objectives were: (1) to investigate the impact of data processing on radar signals; (2) to select a quick, efficient and error-effective data processing for detecting subsurface features; (3) to examine the response of GPR as a function of operating frequency, by using statistical and geostatistical techniques. Six data processing sequences with an increasing level of complexity were applied. The results showed that the type and range of spatial structures of GPR data did not depend on data processing at a given frequency. It was also evident that the noise tended to decrease with the complexity of processing, then the most error-effective procedure was selected. The results highlight the critical importance of the antenna frequency and of the spatial scale of soil/subsoil processes being investigated.

  19. Improvement of RF Wireless Power Transmission Using a Circularly Polarized Retrodirective Antenna Array with EBG Structures

    Directory of Open Access Journals (Sweden)

    Son Trinh-Van

    2018-02-01

    Full Text Available This paper presents the performance improvement of a circularly polarized (CP retrodirective array (RDA through the suppression of mutual coupling effects. The RDA is designed based on CP Koch-shaped patch antenna elements with an inter-element spacing as small as 0.4 λ for a compact size ( λ is the wavelength in free space at the designed frequency of 5.2 GHz. Electromagnetic band gap (EBG structures are applied to reduce the mutual coupling between the antenna elements, thus improving the circular polarization characteristic of the RDA. Two CP RDAs with EBGs, in the case 5 × 5 and 10 × 10 arrays, are used as wireless power transmitters to transmit a total power of 50 W. A receiver is located at a distance of 1 m away from the transmitter to harvest the transmitted power. At the broadside direction, the simulated results demonstrate that the received powers are improved by approximately 11.32% and 12.45% when using the 5 × 5 and 10 × 10 CP RDAs with the EBGs, respectively, as the transmitters.

  20. Shape accuracy optimization for cable-rib tension deployable antenna structure with tensioned cables

    Science.gov (United States)

    Liu, Ruiwei; Guo, Hongwei; Liu, Rongqiang; Wang, Hongxiang; Tang, Dewei; Song, Xiaoke

    2017-11-01

    Shape accuracy is of substantial importance in deployable structures as the demand for large-scale deployable structures in various fields, especially in aerospace engineering, increases. The main purpose of this paper is to present a shape accuracy optimization method to find the optimal pretensions for the desired shape of cable-rib tension deployable antenna structure with tensioned cables. First, an analysis model of the deployable structure is established by using finite element method. In this model, geometrical nonlinearity is considered for the cable element and beam element. Flexible deformations of the deployable structure under the action of cable network and tensioned cables are subsequently analyzed separately. Moreover, the influence of pretension of tensioned cables on natural frequencies is studied. Based on the results, a genetic algorithm is used to find a set of reasonable pretension and thus minimize structural deformation under the first natural frequency constraint. Finally, numerical simulations are presented to analyze the deployable structure under two kinds of constraints. Results show that the shape accuracy and natural frequencies of deployable structure can be effectively improved by pretension optimization.

  1. Objective quantification of mode competition in THz BWO optimization

    Science.gov (United States)

    Bao, Rong; Wang, Hongguang; Zhang, Ruxia; Li, Yongdong; Liu, Chunliang

    2017-11-01

    The corrugated rectangular waveguide slow-wave structure (CRWSWS) terahertz (THz) backward wave oscillator (BWO) is suitable for many applications because of its compactness and portability. An analytical model is proposed for calculating the cold and hot parameters of a CRWSWS THz BWO. Two forms of mode competition are quantified using the analytical model. The quantifications are used as objectives when optimizing the CRWSWS THz BWO. The optimization is performed based on the analytical model and a local search algorithm. The optimization results are verified using CST Microwave Studio and Particle Studio. The influence of one of the quantifications on the convergence of the optimization algorithm is also investigated.

  2. Semiconductor saturable absorbers for ultrafast THz signals

    DEFF Research Database (Denmark)

    Hoffmann, Matthias C.; Turchinovich, Dmitry

    We demonstrate saturable absorber behavior of n-type semiconductors in the THz frequency range using nonlinear THz spectroscopy. Further, we observe THz pulse shortening and increase of the group refractive index at high field strengths.......We demonstrate saturable absorber behavior of n-type semiconductors in the THz frequency range using nonlinear THz spectroscopy. Further, we observe THz pulse shortening and increase of the group refractive index at high field strengths....

  3. A reconfigurable subwavelength plasmonic fano nano-antenna based on split ring resonator

    Energy Technology Data Exchange (ETDEWEB)

    Hosseinbeig, Ahmad; Pirooj, Azadeh [Faculty of Eng., Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Zarrabi, Ferdows B., E-mail: ferdows.zarrabi@yahoo.com [Young Researchers and Elite Club, Babol Branch Islamic Azad University, Babol (Iran, Islamic Republic of)

    2017-02-01

    In this article, a reconfigurable subwavelength plasmonic nano-antenna with Fano resonance effect is presented based on the dual ring structure. In order to achieve reconfigurable characteristics, the interaction of gold with graphene is studied. SiN substrate with refractive index of 1.98 and gold with Palik optical characteristic modified for metal layer are utilized in the design of the proposed nano-antenna. Simulations are performed by using CST Microwave Studio. The biasing effect on extinction cross section is studied for 0 to 0.8 eV. It is shown that the gap method is useful for exciting the Fano resonance in the dual ring nano-antenna and there is only a plasmonic resonance in the simple dual ring antenna. The proposed nano-antenna is useful for THz medical spectroscopy due to its simple design and the ability to control the second resonance frequency by changing the bias of the graphene. - Highlights: • Dual ring structure for Fano resonance with reconfigurable characteristic is suggested. • The gap method is useful for exciting the Fano resonance in the dual ring nano-antenna. • By acheiving the Fano resonance the elctrical field enhanced drastically. • The ability to control the second resonance frequency by changing the bias of the graphene is studied.

  4. Antennas for Terahertz Applications: Focal Plane Arrays and On-chip Non-contact Measurement Probes

    Science.gov (United States)

    Trichopoulos, Georgios C.

    The terahertz (THz) band provides unique sensing opportunities that enable several important applications such as biomedical imaging, remote non-destructive inspection of packaged goods, and security screening. THz waves can penetrate most materials and can provide unique spectral information in the 0.1--10 THz band with high resolution. In contrast, other imaging modalities, like infrared (IR), suffer from low penetration depths and are thus not attractive for non-destructive evaluation. However, state-of-the-art THz imaging systems typically employ mechanical raster scans using a single detector to acquire two-dimensional images. Such devices tend to be bulky and complicated due to the mechanical parts, and are thus rather expensive to develop and operate. Thus, large-format (e.g. 100x100 pixels) and all-electronics based THz imaging systems are badly needed to alleviate the space, weight and power (SWAP) factors and enable cost effective utilization of THz waves for sensing and high-data-rate communications. In contrast, photonic sensors are very compact because light can couple directly to the photodiode without residing to radiation coupling topologies. However, in the THz band, due to the longer wavelengths and much lower photon energies, highly efficient antennas with optimized input impedance have to be integrated with THz sensors. Here, we implement novel antenna engineering techniques that are optimized to take advantage of recent technological advances in solid-state THz sensing devices. For example, large-format focal plane arrays (FPAs) have been the Achilles' heel of THz imaging systems. Typically, optical components (lenses, mirrors) are employed in order to improve the optical performance of FPAs, however, antenna sensors suffer from degraded performance when they are far from the optical axis, thus minimizing the number of useful FPA elements. By modifying the radiation pattern of FPA antennas we manage to alleviate the off-axis aberration

  5. Graphene-enhanced metamaterials in THz applications

    DEFF Research Database (Denmark)

    Andryieuski, Andrei; Chigrin, Dmitry N.; Khromova, Irina

    electromagnetic waves makes them natural candidates for THz optical components [1]. However, ranges of light manipulation can be strongly expanded by involving graphene as a structural component of metamaterials. The interplay between interband and intraband transitions in graphene allows converting a multilayer...... graphene/dielectric structure into a transparent and/or electromagnetically dense artificial medium in a narrow THz or infra-red frequency range. The gate voltage can be used to electrically control the concentration of carriers in the graphene sheets and, thus, efficiently change the dispersion...... of the whole structure. Placed inside a hollow waveguide, a multilayer graphene/dielectric metamaterial provides high-speed modulation of radiation and offers novel concepts for terahertz modulators and tunable bandpass filters. We exemplify it showing performance of waveguide-based terahertz modulators...

  6. A Review of Passive RFID Tag Antenna-Based Sensors and Systems for Structural Health Monitoring Applications.

    Science.gov (United States)

    Zhang, Jun; Tian, Gui Yun; Marindra, Adi M J; Sunny, Ali Imam; Zhao, Ao Bo

    2017-01-29

    In recent few years, the antenna and sensor communities have witnessed a considerable integration of radio frequency identification (RFID) tag antennas and sensors because of the impetus provided by internet of things (IoT) and cyber-physical systems (CPS). Such types of sensor can find potential applications in structural health monitoring (SHM) because of their passive, wireless, simple, compact size, and multimodal nature, particular in large scale infrastructures during their lifecycle. The big data from these ubiquitous sensors are expected to generate a big impact for intelligent monitoring. A remarkable number of scientific papers demonstrate the possibility that objects can be remotely tracked and intelligently monitored for their physical/chemical/mechanical properties and environment conditions. Most of the work focuses on antenna design, and significant information has been generated to demonstrate feasibilities. Further information is needed to gain deep understanding of the passive RFID antenna sensor systems in order to make them reliable and practical. Nevertheless, this information is scattered over much literature. This paper is to comprehensively summarize and clearly highlight the challenges and state-of-the-art methods of passive RFID antenna sensors and systems in terms of sensing and communication from system point of view. Future trends are also discussed. The future research and development in UK are suggested as well.

  7. Plasma process-induced latent damage on gate oxide - demonstrated by single-layer and multi-layer antenna structures

    NARCIS (Netherlands)

    Wang, Zhichun; Ackaert, Jan; Salm, Cora; Kuper, F.G.

    2001-01-01

    In this paper, by using both single-layer (SL) and multi-layer (ML) or stacked antenna structures, a simple experimental method is proposed to directly demonstrate the pure plasma process-induced latent damage on gate oxide without any impact of additional defects generated by normal constant

  8. Design of optical antenna for solar energy collection

    International Nuclear Information System (INIS)

    Gallo, Michele; Mescia, Luciano; Losito, Onofrio; Bozzetti, Michele; Prudenzano, Francesco

    2012-01-01

    In this paper, an antenna array is designed in order to transform the thermal energy, provided by the Sun and re-emitted from the Earth, in electricity. The proposed antenna array is constituted by four square spirals of gold printed on a low cost dielectric substrate. A microstrip line, embedded into the substrate, is used to feed the array and to collect the thermal radiation. The dispersive behavior of gold at infrared frequencies has been taken into account through the Lorentz–Drude model. Simulations have been conducted in order to investigate the behavior of the antenna array illuminated by a circularly polarized plane wave with an amplitude chosen according to the Stefan–Boltzmann radiation law. An output current of about 3.8 μA has been simulated at 28.3 THz, i.e. at the frequency of the Earth emitted radiation. Moreover, these infrared antennas could be coupled with other components to obtain direct rectification of infrared radiation. As a consequence, these structures further optimized could be a promising alternative to the conventional photovoltaic solar cells.

  9. Electromagnetic interference reduction using electromagnetic bandgap structures in packages, enclosures, cavities, and antennas

    Science.gov (United States)

    Mohajer Iravani, Baharak

    Electromagnetic interference (EMI) is a source of noise problems in electronic devices. The EMI is attributed to coupling between sources of radiation and components placed in the same media such as package or chassis. This coupling can be either through conducting currents or through radiation. The radiation of electromagnetic (EM) fields is supported by surface currents. Thus, minimizing these surface currents is considered a major and critical step to suppress EMI. In this work, we present novel strategies to confine surface currents in different applications including packages, enclosures, cavities, and antennas. The efficiency of present methods of EM noise suppression is limited due to different drawbacks. For example, the traditional use of lossy materials and absorbers suffers from considerable disadvantages including mechanical and thermal reliability leading to limited life time, cost, volume, and weight. In this work, we consider the use of Electromagnetic Band Gap (EBG) structures. These structures are suitable for suppressing surface currents within a frequency band denoted as the bandgap. Their design is straight forward, they are inexpensive to implement, and they do not suffer from the limitations of the previous methods. A new method of EM noise suppression in enclosures and cavity-backed antennas using mushroom-type EBG structures is introduced. The effectiveness of the EBG as an EMI suppresser is demonstrated using numerical simulations and experimental measurements. To allow integration of EBGs in printed circuit boards and packages, novel miniaturized simple planar EBG structures based on use of high-k dielectric material (epsilonr > 100) are proposed. The design consists of meander lines and patches. The inductive meander lines serve to provide current continuity bridges between the capacitive patches. The high-k dielectric material increases the effective capacitive load substantially in comparison to commonly used material with much lower

  10. Visualizing proton antenna in a high-resolution green fluorescent protein structure.

    Science.gov (United States)

    Shinobu, Ai; Palm, Gottfried J; Schierbeek, Abraham J; Agmon, Noam

    2010-08-18

    "Proton-collecting antenna" are conjectured to consist of several carboxylates within hydrogen-bond (HB) networks on the surface of proteins, which funnel protons to the orifice of an internal proton wire leading to the protein's active site. Yet such constructions were never directly visualized. Here we report an X-ray structure of green fluorescent protein (GFP) of the highest resolution to date (0.9 A). It allows the identification of some pivotal hydrogen atoms pertinent to uncertainties concerning the protonation state of the chromophore. Applying a computer algorithm for mapping proton wires in proteins reveals the previously observed "active site wire" connecting Glu222 with the surface carboxylate Glu5. In addition, it is now possible to identify what appears to be a proton-collecting apparatus of GFP. It consists of a negative surface patch containing carboxylates, threonines, and water molecules, connected by a HB network to Glu5. Furthermore, we detect exit points via Asn146 and His148 to a hydrophobic surface region. The more extensive HB network of the present structure, as compared with earlier GFP structures, is not accidental. A systematic investigation of over 100 mutants shows a clear correlation between the observed water content of GFP X-ray structures and their resolution. With increasing water content, the proton wires become progressively larger. These findings corroborate the scenario in which the photodissociated proton from wild-type GFP can leak outside, whereafter another proton is recruited via the proton-collecting apparatus reported herein.

  11. Ultrafast electron field emission from gold resonant antennas studied by two terahertz pulse experiments

    DEFF Research Database (Denmark)

    Iwaszczuk, Krzysztof; Zalkovskij, Maksim; Strikwerda, Andrew C.

    2015-01-01

    Summary form only given. Ultrafast electron field emission from gold resonant antennas induced by strong terahertz (THz) transient is investigated using two THz pulse experiments. It is shown that UV emission from nitrogen plasma generated by liberated electrons is a good indication of the local...... electric field at the antenna tip. Using this method resonant properties of antennas fabricated on high resistivity silicon are investigated in the strong field regime. Decrease of antenna Q-factor due to ultrafast carrier multiplication in the substrate is observed....

  12. Design, Optimization and Fabrication of a 28.3...THz Nano-Rectenna for Infrared Detection and Rectification

    KAUST Repository

    Gadalla, M. N.

    2014-03-06

    The increasing energy demands of the world\\'s population and the quickly diminishing fossil fuel reserves together suggest the urgent need to secure long-lasting alternative and renewable energy resources. Here, we present a THz antenna integrated with a rectifier (rectenna) for harvesting infrared energy. We demonstrate a resonant bowtie antenna that has been optimized to produce highly enhanced localized fields at the bow tip. To benefit from this enhancement, the rectifier is realized between the overlapped antenna\\'s arms using a 0.7...nm copper oxide. The thin film diode offers low zero bias resistance of 500...?, thus improving the impedance matching with the antenna. In addition, the rectenna prototype demonstrates high zero bias responsivity (4...A/W), which is critical in producing DC current directly from THz signals without the application of an external electric source, particularly for energy harvesting applications.

  13. Hybrid Computational Simulation and Study of Terahertz Pulsed Photoconductive Antennas

    Science.gov (United States)

    Emadi, R.; Barani, N.; Safian, R.; Nezhad, A. Zeidaabadi

    2016-11-01

    A photoconductive antenna (PCA) has been numerically investigated in the terahertz (THz) frequency band based on a hybrid simulation method. This hybrid method utilizes an optoelectronic solver, Silvaco TCAD, and a full-wave electromagnetic solver, CST. The optoelectronic solver is used to find the accurate THz photocurrent by considering realistic material parameters. Performance of photoconductive antennas and temporal behavior of the excited photocurrent for various active region geometries such as bare-gap electrode, interdigitated electrodes, and tip-to-tip rectangular electrodes are investigated. Moreover, investigations have been done on the center of the laser illumination on the substrate, substrate carrier lifetime, and diffusion photocurrent associated with the carriers temperature, to achieve efficient and accurate photocurrent. Finally, using the full-wave electromagnetic solver and the calculated photocurrent obtained from the optoelectronic solver, electromagnetic radiation of the antenna and its associated detected THz signal are calculated and compared with a measurement reference for verification.

  14. Novel materials, fabrication techniques and algorithms for microwave and THz components, systems and applications

    Science.gov (United States)

    Liang, Min

    This dissertation presents the investigation of several additive manufactured components in RF and THz frequency, as well as the applications of gradient index lens based direction of arrival (DOA) estimation system and broadband electronically beam scanning system. Also, a polymer matrix composite method to achieve artificially controlled effective dielectric properties for 3D printing material is studied. Moreover, the characterization of carbon based nano-materials at microwave and THz frequency, photoconductive antenna array based Terahertz time-domain spectroscopy (THz-TDS) near field imaging system, and a compressive sensing based microwave imaging system is discussed in this dissertation. First, the design, fabrication and characterization of several 3D printed components in microwave and THz frequency are presented. These components include 3D printed broadband Luneburg lens, 3D printed patch antenna, 3D printed multilayer microstrip line structure with vertical transition, THz all-dielectric EMXT waveguide to planar microstrip transition structure and 3D printed dielectric reflectarrays. Second, the additive manufactured 3D Luneburg Lens is employed for DOA estimation application. Using the special property of a Luneburg lens that every point on the surface of the Lens is the focal point of a plane wave incident from the opposite side, 36 detectors are mounted around the surface of the lens to estimate the direction of arrival (DOA) of a microwave signal. The direction finding results using a correlation algorithm show that the averaged error is smaller than 1º for all 360 degree incident angles. Third, a novel broadband electronic scanning system based on Luneburg lens phased array structure is reported. The radiation elements of the phased array are mounted around the surface of a Luneburg lens. By controlling the phase and amplitude of only a few adjacent elements, electronic beam scanning with various radiation patterns can be easily achieved

  15. Structural-electromagnetic bidirectional coupling analysis of space large film reflector antennas

    Science.gov (United States)

    Zhang, Xinghua; Zhang, Shuxin; Cheng, ZhengAi; Duan, Baoyan; Yang, Chen; Li, Meng; Hou, Xinbin; Li, Xun

    2017-10-01

    As used for energy transmission, a space large film reflector antenna (SLFRA) is characterized by large size and enduring high power density. The structural flexibility and the microwave radiation pressure (MRP) will lead to the phenomenon of structural-electromagnetic bidirectional coupling (SEBC). In this paper, the SEBC model of SLFRA is presented, then the deformation induced by the MRP and the corresponding far field pattern deterioration are simulated. Results show that, the direction of the MRP is identical to the normal of the reflector surface, and the magnitude is proportional to the power density and the square of cosine incident angle. For a typical cosine function distributed electric field, the MRP is a square of cosine distributed across the diameter. The maximum deflections of SLFRA linearly increase with the increasing microwave power densities and the square of the reflector diameters, and vary inversely with the film thicknesses. When the reflector diameter becomes 100 m large and the microwave power density exceeds 102 W/cm2, the gain loss of the 6.3 μm-thick reflector goes beyond 0.75 dB. When the MRP-induced deflection degrades the reflector performance, the SEBC should be taken into account.

  16. THz wave parametric oscillator with a surface-emitted ring-cavity configuration

    Science.gov (United States)

    Yang, Zhen; Wang, Yuye; Xu, Degang; Tang, Longhuang; Xu, Wentao; Duan, Pan; Yan, Chao; Yao, Jianquan

    2016-11-01

    A surface-emitted ring-cavity terahertz (THz) wave parametric oscillator has been demonstrated for high-energy THz output and fast frequency tuning. Through the special optical design with a Galvano optical scanner and four-mirror ring-cavity structure, a maximum THz output of 12.9 μJ/pulse is achieved at 1.359 THz under the pump pulse energy of 172.8 mJ with the repetition rate of 10 Hz. A further research on the performance of the SE ring-cavity TPO has done to explore more characteristics of THz output. The THz pulse instability and the influence of cavity loss has analyzed. Moreover, the pump depletion rate of the ring-cavity configuration is much lower than the conventional surface-emitted terahertz wave parametric oscillator at the same experimental conditions.

  17. Thermal radiation antennas made of multilayer structures containing negative index metamaterials

    NARCIS (Netherlands)

    Maksimovic, Milan; Hammer, Manfred; Jaksic, Z.; Greiner, C.M.; Waechter, C.A.

    2008-01-01

    We investigate the thermal antenna behavior of emissive/absorptive substrates coated by passive optical multilayer systems that contain negative refractive index metamaterials (NIM). Spectral and angular distributions of the thermal radiation emittance for periodic defect-containing multilayer with

  18. High impact ionization rate in silicon by sub-picosecond THz electric field pulses (Conference Presentation)

    DEFF Research Database (Denmark)

    Tarekegne, Abebe Tilahun; Iwaszczuk, Krzysztof; Hirori, Hideki

    2017-01-01

    near the antenna tips is measured. Using the NIR probing technique, we observed that the density of carriers increases by over 8 orders of magnitude in a time duration of approximately 500 fs with an incident THz pulse of peak electric field strength 700 kV/cm. This shows that a single impact......Summary form only given. Metallic antenna arrays fabricated on high resistivity silicon are used to localize and enhance the incident THz field resulting in high electric field pulses with peak electric field strength reaching several MV/cm on the silicon surface near the antenna tips. In such high...... electric field strengths high density of carriers are generated in silicon through impact ionization process. The high density of generated carriers induces a change of refractive index in silicon. By measuring the change of reflectivity of tightly focused 800 nm light, the local density of free carriers...

  19. THz wave sensing for petroleum industrial applications

    Science.gov (United States)

    Al-Douseri, Fatemah M.; Chen, Yunqing; Zhang, X.-C.

    2006-04-01

    We present the results of terahertz (THz) sensing of gasoline products. The frequency-dependent absorption coefficients, refractive indices, and complex dielectric constants of gasoline and xylene isomers were extracted in the spectral range from 0.5 3.0 THz. The THz spectra of gasoline (#87, #89, #93) and related BTEX (benzene, toluene, ethylbenzene, and xylene) compounds were studied by using Fourier transform infrared spectroscopy (FTIR) in the 1.5 20 THz (50 660 cm-1). The xylene isomers, which are used as antiknock agent in gasoline were determined quantitatively in gasoline in the THz range. Our investigations show the potential of THz technology for the petroleum industrial applications.

  20. All-optoelectronic continuous wave THz imaging for biomedical applications

    International Nuclear Information System (INIS)

    Siebert, Karsten J; Loeffler, Torsten; Quast, Holger; Thomson, Mark; Bauer, Tobias; Leonhardt, Rainer; Czasch, Stephanie; Roskos, Hartmut G

    2002-01-01

    We present an all-optoelectronic THz imaging system for ex vivo biomedical applications based on photomixing of two continuous-wave laser beams using photoconductive antennas. The application of hyperboloidal lenses is discussed. They allow for f-numbers less than 1/2 permitting better focusing and higher spatial resolution compared to off-axis paraboloidal mirrors whose f-numbers for practical reasons must be larger than 1/2. For a specific histological sample, an analysis of image noise is discussed

  1. Low Noise 1.2 THz SIS Receiver

    Science.gov (United States)

    Karpov, A.; Miller, D.; Rice, F.; Zmuidzinas, J.; Stern, J. A.; Bumble, B.; LeDuc, H. G.

    2001-01-01

    We present the development of a low noise superconductor insulator superconductor (SIS) mixer for the 1.1 - 1.25 THz heterodyne receiver of FIRST space radiotelescope. The quasi-optical SIS mixer has two NbTiN/AlN/Nb junctions with critical current density 30 kA/sq cm. The individual junction area is close to 0.65 square micrometers. The SIS junctions are coupled to the optical input beam through a planar double slot antenna and a Si hyperhemispherical lens. The minimum DSB receiver noise temperature is 650 K, about 12 hv/k.

  2. Organic-inorganic composites for THz device fabrication

    Science.gov (United States)

    Cai, B.; Ye, T. M.; Bo, G.; Wang, X. C.; Li, Y. Z.; Zhu, Y. M.; Sugihara, O.

    2016-02-01

    In this paper, several organic-inorganic composites were prepared for Terahertz (THz) devices fabrication. First, a two-layer structure was designed for femtosecond (fs) laser/THz radiation separation. The top layer was made by sintered 20-40 nm hollow quartz particles which can diffuse the incident fs laser thus decrease the power intensity. The bottom layer comprised of silicon 100 nm particles and cycle-olefine polymer (COP), by which the fs laser light can be greatly scattered and absorbed but THz radiation can propagate insusceptibly. With this two-layer structure a high efficient fs-laser/THz filter was fabricated successfully. Second, titania-polymer composites with a very high refractiveindex tunability and high transparency in the THz region were prepared. By controlling the blending ratio of the titania particle, a broad refractive-index tuning range from 1.5 to 3.1 was realized. Then, the composites were used to fabricate antireflective (AR) layers on a high-resistivity silicon (HR-Si) substrate. By utilizing the thermoplasticity of the titania- polymer composite, a graded-index structure was fabricated via a hot-embossing method. Because of the good refractive-index matching between the composite and the HR-Si substrate, a broadband AR layer was fabricated.

  3. Submillimeter Wave Antenna With Slow Wave Feed Line

    DEFF Research Database (Denmark)

    Zhurbenko, Vitaliy; Krozer, Viktor; Kotiranta, Mikko

    2009-01-01

    Submillimeter wave radiation, which is also referred to as terahertz radiation, has not been extensively explored until recently due to a lack of reliable components and devices in this frequency range. Current advances in technology have made it possible to explore this portion of the electromag......Submillimeter wave radiation, which is also referred to as terahertz radiation, has not been extensively explored until recently due to a lack of reliable components and devices in this frequency range. Current advances in technology have made it possible to explore this portion...... of the electromagnetic spectrum, and to create innovative imaging and sensing techniques that hold enormous potential in biomedical, metrological and security applications. Considering that realization of submillimeter wave components and antennas is still heavily constrained by problems arising from technological...... limitations and the necessity of having extremely miniaturized circuit elements, the design process remains quite challenging. In this paper, a design of a submillimeter wave antenna fed by a slow wave structure is described. The antenna is useful in high-power THz applications because of its ability...

  4. THz near-field imaging of biological tissues employing synchrotronradiation

    Energy Technology Data Exchange (ETDEWEB)

    Schade, Ulrich; Holldack, Karsten; Martin, Michael C.; Fried,Daniel

    2004-12-23

    Terahertz scanning near-field infrared microscopy (SNIM) below 1 THz is demonstrated. The near-field technique benefits from the broadband and highly brilliant coherent synchrotron radiation (CSR) from an electron storage ring and from a detection method based on locking onto the intrinsic time structure of the synchrotron radiation. The scanning microscope utilizes conical wave guides as near-field probes with apertures smaller than the wavelength. Different cone approaches have been investigated to obtain maximum transmittance. Together with a Martin-Puplett spectrometer the set-up enables spectroscopic mapping of the transmittance of samples well below the diffraction limit. Spatial resolution down to about lambda/40 at 2 wavenumbers (0.06 THz) is derived from the transmittance spectra of the near-field probes. The potential of the technique is exemplified by imaging biological samples. Strongly absorbing living leaves have been imaged in transmittance with a spatial resolution of 130 mu-m at about 12 wave numbers (0.36 THz). The THz near-field images reveal distinct structural differences of leaves from different plants investigated. The technique presented also allows spectral imaging of bulky organic tissues. Human teeth samples of various thicknesses have been imaged between 2 and 20 wavenumbers (between 0.06and 0.6 THz). Regions of enamel and dentin within tooth samples are spatially and spectrally resolved, and buried caries lesions are imaged through both the outer enamel and into the underlying dentin.

  5. Development of a structurally integrated conformal load-bearing multifunction antenna: overview of the Air Force Smart Skin Structures Technology Demonstration Program

    Science.gov (United States)

    Lockyer, Allen J.; Alt, Kevin H.; Kinslow, Robert W.; Kan, Han-Pin; Kudva, Jayanth N.; Tuss, James; Goetz, Allan C.

    1996-05-01

    The Structures Division of the Air Force's Wright Laboratory is sponsoring the development and demonstration of a new high pay-off technology termed CLAS--Conformal Load Bearing Antenna Structures. Northrop Grumman Corporation and TRW/ASD are developing the technology under the `Smart-Skin Structure Technology Demonstration (S3D)' program, contract, No. F33615-93-C-3200. The program goal is to design, develop, fabricate, and test a CLAS component and lay the foundation for future work where potential benefits from structurally integrated antennas may be realized. Key issues will focus but are not limited to the design, structures, and manufacturing aspects of antenna embedment into load bearing aircraft structures. Results from Phase I of the program have been previously reported, where initial pay-offs in reducing overall airframe acquisition and support cost, weight, signature, and drag were quantitatively and qualitatively identified. A full-sized CLAS component, featuring a broadband multi-arm spiral embedded in sandwich stiffened structure, will be fabricated and tested for static strength, durability, and damage tolerance. Basic electrical performance, (e.g. radiation patterns, gain, and impedance) will also be verified; however, extensive electrical validation will be the subject of further work. Key aspects of the work and progress to date are detailed below.

  6. THz plasmonic modes in metal-clad planar multilayer waveguides

    Science.gov (United States)

    Ghamsari, Behnood G.; Majedi, A. Hamed

    2009-05-01

    This paper studies the role of plasmonic modes for guided-wave propagation of THz/far infrared in metalclad planar waveguides, including metal-dielectric interfaces, dielectric-loaded metal slabs and parallel plate waveguides. The dispersion of modal characteristics of the plasmonic guided waves, such as the effective index, attenuation constant and the field confinement, as a function of geometrical features for different consisting materials and wavelengths are examined. Moreover, comparison is made between the THz plasmonic modes to their optical counterparts at visible/near infrared within the similar physical structures. Peculiar features of each structure are highlighted and regimes of interest are distinguished.

  7. THz reflectometric imaging of of contemporary panel artwork

    DEFF Research Database (Denmark)

    Dandolo, Corinna Ludovica Koch; Jepsen, Peter Uhd

    2013-01-01

    Terahertz time-domain reflectometry has been applied to the investigation of a tempera panel replica. The technique has given useful information about the surface as well as the internal structure of the artworks. Ultrathin layers of leaf gold are penetrated by THz radiation, revealing the underl......Terahertz time-domain reflectometry has been applied to the investigation of a tempera panel replica. The technique has given useful information about the surface as well as the internal structure of the artworks. Ultrathin layers of leaf gold are penetrated by THz radiation, revealing...

  8. 47 CFR 95.51 - Antenna height.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Antenna height. 95.51 Section 95.51... SERVICES General Mobile Radio Service (GMRS) § 95.51 Antenna height. (a) Certain antenna structures used in... this chapter. (b) The antenna for a small base station or for a small control station must not be more...

  9. Monolithic, Widely Tunable, THz Local Oscillator Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal describes development of a new type of quantum-cascade laser for use as a local oscillator at frequencies above 2 THz. The THz source described is a...

  10. Geometrical Aberration Suppression for Large Aperture Sub-THz Lenses

    Science.gov (United States)

    Rachon, M.; Liebert, K.; Siemion, A.; Bomba, J.; Sobczyk, A.; Knap, W.; Coquillat, D.; Suszek, J.; Sypek, M.

    2017-03-01

    Advanced THz setups require high performance optical elements with large numerical apertures and small focal lengths. This is due to the high absorption of humid air and relatively low efficiency of commercially available detectors. Here, we propose a new type of double-sided sub-THz diffractive optical element with suppressed geometrical aberration for narrowband applications (0.3 THz). One side of the element is designed as thin structure in non-paraxial approach which is the exact method, but only for ideally flat elements. The second side will compensate phase distribution differences between ideal thin structure and real volume one. The computer-aided optimization algorithm is performed to design an additional phase distribution of correcting layer assuming volume designing of the first side of the element. The experimental evaluation of the proposed diffractive component created by 3D printing technique shows almost two times larger performance in comparison with uncorrected basic diffractive lens.

  11. A Novel Inversion Method of Manufacturing Flaws in the Packaging of Conformal Load-Bearing Antenna Structure

    Directory of Open Access Journals (Sweden)

    P. Li

    2015-01-01

    Full Text Available Composite material is widely used in the conformal load-bearing antenna structure (CLAS, and the manufacturing flaws in the packaging process of the CLAS will lead to the degradation of its wave-transparent property. For this problem, a novel inverse method of the flaw’s dimension by antenna-radome system’s far field data has been proposed. Two steps are included in the inversion: the first one is the inversion from the far filed data to the transmission coefficient of the CLAS’s radome; the second one is the inversion from the transmission coefficient to the flaw’s dimension. The inversion also has a good potential for the separable multilayer composite material radome. A 12.5 GHz CLAS with microstrip antenna array is used in the simulation, which indicates the effectiveness of the novel inversion method. Finally, the error analysis of the inversion method is presented by numerical simulation; the results is that the inversed error could be less than 10%, if the measurement error of far field data is less than 0.45 dB in amplitude and ±5° in phase.

  12. Reconfigurable antenna pattern verification

    Science.gov (United States)

    Drexler, Jerome P. (Inventor); Becker, Robert C. (Inventor); Meyers, David W. (Inventor); Muldoon, Kelly P. (Inventor)

    2013-01-01

    A method of verifying programmable antenna configurations is disclosed. The method comprises selecting a desired antenna configuration from a plurality of antenna configuration patterns, with the selected antenna configuration forming at least one reconfigurable antenna from reconfigurable antenna array elements. The method validates the formation of the selected antenna configuration to determine antenna performance of the at least one reconfigurable antenna.

  13. Exploration of the effects of burn parameters on THz wound imaging

    Science.gov (United States)

    Bajwa, Neha; Sung, Shijun; Fishbein, Michael; Grundfest, Warren S.; Taylor, Zachary D.

    2015-08-01

    The high contrast resolution afforded by terahertz (1 THz = 1012 Hz) imaging of physiologic tissue continues to drive explorations into the utility of THz technology for burn wound detection. Although we have previously reported the use of a novel, reflective THz imaging technology to sense spatiotemporal differences in reflectivity between partial and full thickness burn wounds, no evidence exists of a one-to-one correlation between structural damage observed in histological assessments of burn severity and THz signal. For example, varying burn induction methods may all result in a common burn wound severity, however, burn features observed in parallel THz imagery may not be identical. Successful clinical translation of THz technology as a comprehensive burn guidance tool, therefore, necessitates an understanding of THz signal and its relation to wound pathophysiology. In this work, longitudinal THz imagery was acquired with a quartz (n = 2.1, 500 μm) window of cutaneous wounds induced with the same brand geometry and contact pressure but varying contact times (5, 7, and 10 seconds) in in vivo, pre-clinical rat models (n=3) over a period of 3 days. Though all burn wounds were evaluated to be deep partial thickness with histology, THz contrasts observed for each burn contact time were intrinsically unique. This is the first preliminary in vivo evidence of a many-to-one relationship between changes in THz contrast and burn severity as ascertained by histology. Future large-scale studies are required to assess whether these observed changes in THz contrast may be interpreted as physiological changes occurring over time, morphometric changes related to anatomical change, or electromagnetic changes between dielectric substrate windows and the underlying tissue.

  14. Temperature-dependent THz vibrational spectra of clenbuterol hydrochloride

    Science.gov (United States)

    Yang, YuPing; Lei, XiangYun; Yue, Ai; Zhang, Zhenwei

    2013-04-01

    Using the high-resolution Terahertz Time-domain spectroscopy (THz-TDS) and the standard sample pellet technique, the far-infrared vibrational spectra of clenbuterol hydrochloride (CH), a β 2-adrenergic agonist for decreasing fat deposition and enhancing protein accretion, were measured in temperature range of 77-295 K. Between 0.2 and 3.6 THz (6.6-120.0 cm-1), seven highly resolved spectral features, strong line-narrowing and a frequency blue-shift were observed with cooling. However, ractopamine hydrochloride, with some structural and pharmacological similarities to clenbuterol hydrochloride, showed no spectral features, indicating high sensitivity and strong specificity of THz-TDS. These results could be used for the rapid and nondestructive CH residual detection in food safety control.

  15. Disc-coupled Dots-on-Pillar Antenna Array (D2PA) as a nanoplasmonic structure and its application

    Science.gov (United States)

    Ding, Fei

    The research work presented in this dissertation includes design, fabrication and optimization of the Disc-Coupled Dots-on-Pillar Antenna Array (D2PA) structure, and its application to Surface Enhanced Raman Scattering (SERS). The first portion of the thesis contains a review of localized surface plasmon and nanoplasmonic structures (nanoparticle systems and antenna systems), followed by the design, fabrication and characterization of D2PA. The second part of the thesis focuses on the structural optimization of D2PA, including the nanodots on pillar sidewalls, the disc shape, the disc thickness, and the use of a surface coating. In the third part of the thesis, the use of D2PA in SERS is illustrated with two examples: explosive material detection with Trinitrotoluene (TNT), and residual pesticide detection with carbendazim in orange juice. Several related topics are addressed in the appendices, including Moire pattern analysis, spectrum classification program, D2PA structures made with 'gain' materials, and the application of Multiple Double Nanoimprint Lithography (MD-NIL) and Moire patterns in Gradient Index Lenses (GRIN).

  16. Antenna toolkit

    CERN Document Server

    Carr, Joseph

    2006-01-01

    Joe Carr has provided radio amateurs and short-wave listeners with the definitive design guide for sending and receiving radio signals with Antenna Toolkit 2nd edition.Together with the powerful suite of CD software, the reader will have a complete solution for constructing or using an antenna - bar the actual hardware! The software provides a simple Windows-based aid to carrying out the design calculations at the heart of successful antenna design. All the user needs to do is select the antenna type and set the frequency - a much more fun and less error prone method than using a con

  17. Terahertz Nanofocusing with Cantilevered Terahertz-Resonant Antenna Tips.

    Science.gov (United States)

    Mastel, Stefan; Lundeberg, Mark B; Alonso-González, Pablo; Gao, Yuanda; Watanabe, Kenji; Taniguchi, Takashi; Hone, James; Koppens, Frank H L; Nikitin, Alexey Y; Hillenbrand, Rainer

    2017-11-08

    We developed THz-resonant scanning probe tips, yielding strongly enhanced and nanoscale confined THz near fields at their tip apex. The tips with length in the order of the THz wavelength (λ = 96.5 μm) were fabricated by focused ion beam (FIB) machining and attached to standard atomic force microscopy (AFM) cantilevers. Measurements of the near-field intensity at the very tip apex (25 nm radius) as a function of tip length, via graphene-based (thermoelectric) near-field detection, indicate their first and second order geometrical antenna resonances for tip length of 33 and 78 μm, respectively. On resonance, we find that the near-field intensity is enhanced by one order of magnitude compared to tips of 17 μm length (standard AFM tip length), which is corroborated by numerical simulations that further predict remarkable intensity enhancements of about 10 7 relative to the incident field. Because of the strong field enhancement and standard AFM operation of our tips, we envision manifold and straightforward future application in scattering-type THz near-field nanoscopy and THz photocurrent nanoimaging, nanoscale nonlinear THz imaging, or nanoscale control and manipulation of matter employing ultrastrong and ultrashort THz pulses.

  18. Edge transport and mode structure of a QCM-like fluctuation driven by the Shoelace antenna

    Science.gov (United States)

    Golfinopoulos, T.; LaBombard, B.; Brunner, D.; Terry, J. L.; Baek, S. G.; Ennever, P.; Edlund, E.; Han, W.; Burke, W. M.; Wolfe, S. M.; Irby, J. H.; Hughes, J. W.; Fitzgerald, E. W.; Granetz, R. S.; Greenwald, M. J.; Leccacorvi, R.; Marmar, E. S.; Pierson, S. Z.; Porkolab, M.; Vieira, R. F.; Wukitch, S. J.; The Alcator C-Mod Team

    2018-05-01

    The Shoelace antenna was built to drive edge fluctuations in the Alcator C-Mod tokamak, matching the wavenumber (k\\perp≈1.5 cm‑1) and frequency (30≲ f ≲ 200 kHz) of the quasi-coherent mode (QCM), which is responsible for regulating transport across the plasma boundary in the steady-state, ELM-free Enhanced D α (EDA) H-mode. Initial experiments in 2012 demonstrated that the antenna drove a resonant response in the edge plasma in steady-state EDA and transient, non-ELMy H-modes, but transport measurements were unavailable. In 2016, the Shoelace antenna was relocated to enable direct measurements of driven transport by a reciprocating Mirror Langmuir Probe, while also making available gas puff imaging and reflectometer data to provide additional radial localization of the driven fluctuation. This new data suggests a  ∼4 mm-wide mode layer centered on or just outside the separatrix. Fluctuations coherent with the antenna produced a radial electron flux with {Γ_e}/{n_e}∼4 m s‑1 in EDA H-mode, smaller than but comparable to the QCM level. But in transient ELM-free H-mode, {Γ_e}/{n_e} was an order of magnitude smaller, and driven fluctuations reduced by a factor of ≳ 3. The driven mode is quantitatively similar to the intrinsic QCM across measured spectral quantities, except that it is more coherent and weaker. This work informs the prospect of achieving control of edge transport by direct coupling to edge modes, as well as the use of such active coupling for diagnostic purposes.

  19. Tunable photonic crystal for THz radiation in layered superconductors: Strong magnetic-field dependence of the transmission coefficient

    International Nuclear Information System (INIS)

    Savel'ev, Sergey; Rakhmanov, A.L.; Nori, Franco

    2006-01-01

    Josephson plasma waves are scattered by the Josephson vortex lattice. This scattering results in a strong dependence, on the in-plane magnetic-field H ab , of the reflection and transmission of THz radiation propagating in layered superconductors. In particular, a tunable band-gap structure (THz photonic crystal) occurs in such a medium. These effects can be used, by varying H ab , for the selective frequency-filtering of THz radiation

  20. THz Photonic Band-Gap Prisms Fabricated by Fiber Drawing

    DEFF Research Database (Denmark)

    Busch, Stefan F.; Xu, Lipeng; Stecher, Matthias

    2012-01-01

    We suggest a novel form of polymeric based 3D photonic crystal prisms for THz frequencies which could be fabricated using a standard fiber drawing technique. The structures are modeled and designed using a finite element analyzing technique. Using this simulation software we theoretically study...

  1. Fiber-Drawn Metamaterial for THz Waveguiding and Imaging

    DEFF Research Database (Denmark)

    Atakaramians, Shaghik; Stefani, Alessio; Li, Haisu

    2017-01-01

    In this paper, we review the work of our group in fabricating metamaterials for terahertz (THz) applications by fiber drawing. We discuss the fabrication technique and the structures that can be obtained before focusing on two particular applications of terahertz metamaterials, i.e., waveguiding...

  2. Elliptical metasurfaces for cloaking and antenna applications at microwave and terahertz frequencies

    Science.gov (United States)

    Mehrpourbernety, Hossein

    One of the interesting applications of metamaterials is the phenomenon of electromagnetic invisibility and cloaking, which implies the suppression of bistatic scattering width of a given object, independent of incident and observation angles. In this regard, diverse techniques have been proposed to analyze and design electromagnetic cloak structures, including transformation optics, anomalous resonance methods, transmission-line networks, and plasmonic cloaking, among others. A common drawback of all these methods is that they rely on bulk materials, which are difficult to realize in practice. To overcome this issue, the mantle cloaking method has been proposed, which utilizes an ultrathin metasurface that provides anti-phase surface currents to reduce the scattering dominant mode of a given object. Recently, an analytical model has been proposed to cloak dielectric and conducting cylindrical objects realized with printed and slotted arrays at microwave frequencies. At low-terahertz (THz) frequencies, one of the promising materials to realize the required metasurface is graphene. In this regard, a graphene monolayer, characterized by inductive reactance, has been proposed to cloak dielectric planar and cylindrical objects. Then, it has been shown that a metasurface made of graphene nanopatches owns dual capacitive/inductive inductance and can be used to cloak both dielectric and conducting cylindrical objects at low-THz frequencies. So far, planar and cylindrical dielectric and conducting structures have been studied. In our study, we have extended the concept and presented an accurate analytical approach to investigate the cloaking of two-dimensional (2-D) elliptical objects including infinite dielectric elliptical cylinders using graphene monolayer; metallic elliptical cylinders, and also, as a special case, 2-D metallic strips using a nanostructured graphene patch array at low-THz frequencies. We have also obtained the results for cloaking of ellipses at

  3. Bridging the gap between the THz and IR frequency regime

    DEFF Research Database (Denmark)

    Kaltenecker, Korbinian J.; Zhou, Binbin; Stenger, Nicolas

    2017-01-01

    THz air photonics allow for the generation and detection of single-cycle sub-40 fs THz transients, which we use in a THz time-domain spectrometer to investigate the transmission properties of molecular crystalline materials in the ultrabroadband frequency window from 0.3 THz to more than 40 THz. ...

  4. Paper on Designing Costless THz Paper Optics

    Directory of Open Access Journals (Sweden)

    A. Siemion

    2016-01-01

    Full Text Available Designing diffractive optical elements is crucial for efficient development of THz techniques. Here, we consider paper structures and we analyze their advantages and disadvantages in fast prototyping. The discussion about using material parameters like refractive index and absorption coefficient in designing diffractive optical elements is shown. We analyze the influence of phase step mismatch, of attenuation of real structure, and of nonuniform illumination on the efficiency of the structure. All these features result in worsening of the diffraction efficiency but they do not seem to have such significant influence as shadow effect introduced by fast varying zones. Diffractive elements can be designed with very good accordance with experimental results which makes them ideal for possible applications. Paper optics scan be used more for fast prototyping; nevertheless its performance can be increased by placing it inside water protecting foil.

  5. Improved Gain Microstrip Patch Antenna

    Science.gov (United States)

    2015-08-06

    frequency selective structure (FSS) as a layer above a microstrip patch antenna. This is done to filter undesirable frequencies. For this purpose the FSS...is used for isolating the antenna from the filtered frequency, not improving the gain of the antenna. [0008] Thus, there is a need for microstrip...selective surface applied. The passband is generally indicated as the region where the curve passes below a VSWR of 3. These results indicate a

  6. Flexible ultra-wideband antenna incorporated with metamaterial structures: multiple notches for chipless RFID application

    Science.gov (United States)

    Jalil, M. E.; Rahim, M. K. A.; Samsuri, N. A.; Dewan, R.; Kamardin, K.

    2017-01-01

    A coplanar waveguide (CPW) ultra-wideband (UWB) antenna incorporated with metamaterial—split ring resonator structure—that operates from 3.0 to 12.0 GHz is proposed for chipless RFID tag. The 30 mm × 40 mm flexible chipless RFID tag is designed on the fleece substrate ( ɛ r = 1.35, thickness = 1 mm and tan δ = 0.025). A six-slotted modified complementary split ring resonator (MCSRR) is introduced into the ultra-wideband antenna to produce multiple band notches at 3.0, 4.0, 5.0, 6.0 and 7.0 GHz. The frequency shifting technique is introduced for designing a high-capacity chipless RFID tag with compact size. Each MCSRR is able to code in four different allocations (00, 01, 10 and 11). To achieve encoding of 10-bits data (10,234 number), six MCSRRs are proposed with three-slotted MCSRR in the radiator and three-slotted MCSRR in the ground plane.

  7. Multi-Band Wireless Terminals With A Hybrid Antenna Along An End Portion, And Related Multi-Band Antenna Systems

    DEFF Research Database (Denmark)

    2014-01-01

    An antenna system may include a backplate that includes an end portion. The antenna system may also include a hybrid antenna that includes first and second antenna elements spaced apart from each other along the end portion of the backplate. The first antenna element may include a type of antenna...... element that is structurally different from the second antenna element. Additionally, the antenna system may further include a parasitic element between the first and second antenna elements along the end portion of the backplate....

  8. Generation of THz frequency using PANDA ring resonator for THz imaging

    Science.gov (United States)

    Jalil, MA; Abdolkarim, Afroozeh; Saktioto, T; Ong, CT; Yupapin, Preecha P

    2012-01-01

    In this study, we have generated terahertz (THz) frequency by a novel design of microring resonators for medical applications. The dense wavelength-division multiplexing can be generated and obtained by using a Gaussian pulse propagating within a modified PANDA ring resonator and an add/drop filter system. Our results show that the THz frequency region can be obtained between 40–50 THz. This area of frequency provides a reliable frequency band for THz pulsed imaging. PMID:22359455

  9. Investigation of graphene-integrated tunable metamaterials in THz regime

    Science.gov (United States)

    Demir, S. Mahircan; Yüksek, Yahya; Sabah, Cumali

    2018-05-01

    A metallic fishnet metamaterial structure in sub-THz region is presented. The proposed structure is based on hexagonal resonators. Simulations have been performed by a 3D full-wave electromagnetic simulator and a negative refractive index has been observed at the frequency range between 0.55 and 0.70 THz with the help of the graphene layer. In order to observe the effect of the graphene layer, the metamaterial structure has been simulated and examined before and after graphene integration. Significant modification in the propagation properties has been observed after the graphene integration. Change in S-parameters with the size variation of hexagonal resonators and alteration in graphene thickness are also presented as a parametric study to show the tunability of the structure. Suitability of the metamaterial for sensor applications has been investigated. The proposed metamaterial structure is promising to be effectively used for tunability and sensor applications.

  10. Efficient power combiner for THz radiation

    Directory of Open Access Journals (Sweden)

    Hamide Seidfaraji

    2016-08-01

    Full Text Available Most dangerous explosive materials, both toxic and radioactive, contain nitrogen salts with resonant absorption lines in the frequency range 0.3-10 THz. Therefore, there has been growing interest in remotely detecting such materials by observing the spectrum of reflected signals when the suspicious material is interrogated by THz radiation. Practical portable THz sources available today generate only 20–40 mW output power. This power level is too low to interrogate suspicious material from a safe distance, especially if the material is concealed. Hence, there is a need for sources that can provide greater power in the THz spectrum. Generating and extracting high output power from THz sources is complicated and inefficient. The efficiency of vacuum electronic microwave sources is very low when scaled to the THz range and THz sources based on scaling down semiconductor laser sources have low efficiency as well, resulting in the well known “THz gap.” The reason for such low efficiencies for both source types is material losses in the THz band. In this article an efficient power combiner is described that is based on scaling to higher frequencies a microwave combiner that increases the output power in the THz range of interest in simulation studies. The proposed power combiner not only combines the THz power output from several sources, but can also form a Gaussian wavebeam output. A minimum conversion efficiency of 89% with cophased inputs in a lossy copper power combiner and maximum efficiency of 100% in a Perfect Electric Conductor (PEC-made power combiner were achieved in simulations. Also, it is shown that the TE01 output mode is a reasonable option for THz applications due to the fact that conductive loss decreases for this mode as frequency increases.

  11. Survey of Antenna Design Computer Models

    Science.gov (United States)

    1992-12-24

    May, A. Taflove, K. R. Umashankar, FDTD Analysis of Electromagnetic Wave Radiation from Systems Containing Horn Antennas , IEEE Trans. on Antennas and...sample grid structure of a waveguide slot antenna . 2D Open Boundary Pure of Symmewy Element Termination Lacotle of dot Figure 4. Grid structure for...finite element modeling of a waveguide slot antenna and surrounding air. 2 1 11 Finite elements are frequently shaped like triangles or rectangles in 2D

  12. Inherent resistivity of graphene to strong THz fields

    DEFF Research Database (Denmark)

    Turchinovich, Dmitry; Mics, Zoltán; Jensen, Søren

    2014-01-01

    The nonlinear THz conductivity of graphene is characterized using nonlinear ultrafast THz spectroscopy. Efficient carrier heating by the THz field reduces carrier scattering, yet, counter-intuitively, simultaneously suppresses the high-frequency conductivity of graphene. © 2014 OSA....

  13. Hot-Electron Gallium Nitride Two Dimensional Electron Gas Nano-bolometers For Advanced THz Spectroscopy

    Science.gov (United States)

    Ramaswamy, Rahul

    Two-dimensional electron gas (2DEG) in semiconductor heterostructures was identified as a promising medium for hot-electron bolometers (HEB) in the early 90s. Up until now all research based on 2DEG HEBs is done using high mobility AlGaAs/GaAs heterostructures. These systems have demonstrated very good performance, but only in the sub terahertz (THz) range. However, above ˜0.5 THz the performance of AlGaAs/GaAs detectors drastically deteriorates. It is currently understood, that detectors fabricated from standard AlGaAs/GaAs heterostructures do not allow for reasonable coupling to THz radiation while maintaining high conversion efficiency. In this work we have developed 2DEG HEBs based on disordered Gallium Nitride (GaN) semiconductor, that operate at frequencies beyond 1THz at room temperature. We observe strong free carrier absorption at THz frequencies in our disordered 2DEG film due to Drude absorption. We show the design and fabrication procedures of novel micro-bolometers having ultra-low heat capacities. In this work the mechanism of 2DEG response to THz radiation is clearly identified as bolometric effect through our direct detection measurements. With optimal doping and detector geometry, impedances of 10--100 O have been achieved, which allow integration of these devices with standard THz antennas. We also demonstrate performance of the antennas used in this work in effectively coupling THz radiation to the micro-bolometers through polarization dependence and far field measurements. Finally heterodyne mixing due to hot electrons in the 2DEG micro-bolometer has been performed at sub terahertz frequencies and a mixing bandwidth greater than 3GHz has been achieved. This indicates that the characteristic cooling time in our detectors is fast, less than 50ps. Due to the ultra-low heat capacity; these detectors can be used in a heterodyne system with a quantum cascade laser (QCL) as a local oscillator (LO) which typically provides output powers in the micro

  14. Stretchable antenna for wearable electronics

    KAUST Repository

    Hussain, Muhammad Mustafa

    2017-04-13

    Various examples are provided for stretchable antennas that can be used for applications such as wearable electronics. In one example, a stretchable antenna includes a flexible support structure including a lateral spring section having a proximal end and at a distal end; a metallic antenna disposed on at least a portion of the lateral spring section, the metallic antenna extending along the lateral spring section from the proximal end; and a metallic feed coupled to the metallic antenna at the proximal end of the lateral spring section. In another example, a method includes patterning a polymer layer disposed on a substrate to define a lateral spring section; disposing a metal layer on at least a portion of the lateral spring section, the metal layer forming an antenna extending along the portion of the lateral spring section; and releasing the polymer layer and the metal layer from the substrate.

  15. New investigation on THz spectra of OH and SH radicals (X∏)

    Science.gov (United States)

    Martin-Drumel, M. A.; Eliet, S.; Pirali, O.; Guinet, M.; Hindle, F.; Mouret, G.; Cuisset, A.

    2012-10-01

    Pure rotational transitions of OH and SH radicals have been recorded in the THz spectral range using cw-THz and synchrotron-based FT-FIR techniques. Line lists on these radicals have been completed in the three and two lowest vibrational states for OH and SH, respectively. Furthermore, the hyperfine structure of OH and SH has been observed for the first time using infrared IR FT-spectroscopy, and at frequencies higher than 1 THz, respectively. A combined fit has been made for each of these radicals including v = 0, 1 and 2 for OH and v = 0 and 1 for SH.

  16. Prediction of the electrical performance of Inflatable Space Rigidized Structure (ISRS) offset antenna reflectors and correlation with RF measurements

    Science.gov (United States)

    Pagana, E.; Bernasconi, M. C.

    1986-08-01

    The electrical design and testing at microwave frequencies (3 to 22 GHz) on the first Large Offset Antenna Demonstrator (LOAD) breadboard are summarized. The electrical analysis shows the quality of mock-up reflector and contributes to an electrical antenna model. The performance of a large inflatable antenna can be predicted, with good accuracy, only on the basis of the mechanical measurements of a proper set of reflector surface points.

  17. Backfire antennas with dipole elements

    DEFF Research Database (Denmark)

    Nielsen, Erik Dragø; Pontoppidan, Knud

    1970-01-01

    A method is set up for a theoretical investigation of arbitrary backfire antennas based upon dipole structures. The mutual impedance between the dipole elements of the antenna is taken into account, and the field radiated due to a surface wave reflector of finite extent is determined by calculating...

  18. A Reconfigurable Triple-Notch-Band Antenna Integrated with Defected Microstrip Structure Band-Stop Filter for Ultra-Wideband Cognitive Radio Applications

    Directory of Open Access Journals (Sweden)

    Yingsong Li

    2013-01-01

    Full Text Available A printed reconfigurable ultra-wideband (UWB monopole antenna with triple narrow band-notched characteristics is proposed for cognitive radio applications in this paper. The triple narrow band-notched frequencies are obtained using a defected microstrip structure (DMS band stop filter (BSF embedded in the microstrip feed line and an inverted π-shaped slot etched in the rectangular radiation patch, respectively. Reconfigurable characteristics of the proposed cognitive radio antenna (CRA are achieved by means of four ideal switches integrated on the DMS-BSF and the inverted π-shaped slot. The proposed UWB CRA can work at eight modes by controlling switches ON and OFF. Moreover, impedance bandwidth, design procedures, and radiation patterns are presented for analysis and explanation of this antenna. The designed antenna operates over the frequency band between 3.1 GHz and 14 GHz (bandwidth of 127.5%, with three notched bands from 4.2 GHz to 6.2 GHz (38.5%, 6.6 GHz to 7.0 GHz (6%, and 12.2 GHz to 14 GHz (13.7%. The antenna is successfully simulated, fabricated, and measured. The results show that it has wide impedance bandwidth, multimodes characteristics, stable gain, and omnidirectional radiation patterns.

  19. Experimental modal analysis and dynamic strain fiber Bragg gratings for structural health monitoring of composite antenna sub-reflector

    Science.gov (United States)

    Panopoulou, A.; Fransen, S.; Gomez-Molinero, V.; Kostopoulos, V.

    2013-09-01

    The objective of this work is to develop a new structural health monitoring system for composite aerospace structures based on dynamic response strain measurements and experimental modal analysis techniques. Fiber Bragg grating (FBG) optical sensors were used for monitoring the dynamic response of the composite structure. The structural dynamic behavior has been numerically simulated and experimentally verified by means of vibration testing. The hypothesis of all vibration tests was that actual damage in composites reduces their stiffness and produces an eigenfrequency shifting to lower values in the same sense as mass increase produces. Thus, damage was simulated by slightly varying locally the mass of the structure at different zones. The correlation between the simulated damage and the loss of stiffness was analytically defined. Experimental modal analysis based on the strain responses was conducted and the extracted strain mode shapes were the input for the damage detection expert system. A feed-forward back propagation neural network was the core of the damage detection system. The features-input to the neural network consisted of the strain mode shapes, extracted from the experimental modal analysis. Dedicated training and validation activities were carried out based on the experimental results. The system showed high reliability, confirmed by the ability of the neural network to recognize the size and the position of damage on the structure. The experiments were performed on a real structure i.e. a lightweight antenna sub-reflector, manufactured and tested at EADS CASA ESPACIO. An integrated FBG sensor network, based on the advantage of multiplexing, was mounted on the structure with optimum topology. Numerical simulation was used as a support tool at all the steps of the work. Potential applications for the proposed system are during ground qualification extensive tests of space structures and during the mission as modal analysis tool on board, being able

  20. Circularly polarized antennas

    CERN Document Server

    Gao, Steven; Zhu, Fuguo

    2013-01-01

    This book presents a comprehensive insight into the design techniques for different types of CP antenna elements and arrays In this book, the authors address a broad range of topics on circularly polarized (CP) antennas. Firstly, it introduces to the reader basic principles, design techniques and characteristics of various types of CP antennas, such as CP patch antennas, CP helix antennas, quadrifilar helix antennas (QHA), printed quadrifilar helix antennas (PQHA), spiral antenna, CP slot antennas, CP dielectric resonator antennas, loop antennas, crossed dipoles, monopoles and CP horns. Adva

  1. Majolica imaging with THz waves: preliminary results

    Science.gov (United States)

    Catapano, Ilaria; Affinito, Antonio; Guerriero, Luigi; Bisceglia, Bruno; Soldovieri, Francesco

    2016-05-01

    Recent advancements performed in the development of stable and flexible devices working at TeraHertz (THz) frequencies have opened the way at considering this technology as a very interesting noninvasive diagnostic tool in cultural heritage. In this frame, the paper aims at assessing the ability of THz imaging to gather information about preservation state and constructive modalities of majolica artworks. In particular, THz surveys have been carried out on two majolica tiles dated back to the nineteenth century and realized as building cladding at Naples (Italy). The analysis has been performed by means of the Zomega fiber-coupled THz time-domain system. This analysis corroborates the ability of THz to reconstruct irregularities of majolica tile topography, to characterize pigment and glaze losses, and to detect and localize glaze and pigment layer as well as the glaze-clay body interface.

  2. Piroxicam derivatives THz classification

    Science.gov (United States)

    Sterczewski, Lukasz A.; Grzelczak, Michal P.; Nowak, Kacper; Szlachetko, Bogusław; Plinska, Stanislawa; Szczesniak-Siega, Berenika; Malinka, Wieslaw; Plinski, Edward F.

    2016-02-01

    In this paper we report a new approach to linking the terahertz spectral shapes of drug candidates having a similar molecular structure to their chemical and physical parameters. We examined 27 newly-synthesized derivatives of a well-known nonsteroidal anti-inflammatory drug Piroxicam used for treatment of inflammatory arthritis and chemoprevention of colon cancer. The testing was carried out by means of terahertz pulsed spectroscopy (TPS). Using chemometric techniques we evaluated their spectral similarity in the terahertz range and attempted to link the position on the principal component analysis (PCA) score map to the similarity of molecular descriptors. A simplified spectral model preserved 75% and 85.1% of the variance in 2 and 3 dimensions respectively, compared to the input 1137. We have found that in 85% of the investigated samples a similarity of the physical and chemical parameters corresponds to a similarity in the terahertz spectra. The effects of data preprocessing on the generated maps are also discussed. The technique presented can support the choice of the most promising drug candidates for clinical trials in pharmacological research.

  3. Cup Cylindrical Waveguide Antenna

    Science.gov (United States)

    Acosta, Roberto J.; Darby, William G.; Kory, Carol L.; Lambert, Kevin M.; Breen, Daniel P.

    2008-01-01

    The cup cylindrical waveguide antenna (CCWA) is a short backfire microwave antenna capable of simultaneously supporting the transmission or reception of two distinct signals having opposite circular polarizations. Short backfire antennas are widely used in mobile/satellite communications, tracking, telemetry, and wireless local area networks because of their compactness and excellent radiation characteristics. A typical prior short backfire antenna contains a half-wavelength dipole excitation element for linear polarization or crossed half-wavelength dipole elements for circular polarization. In order to achieve simultaneous dual circular polarization, it would be necessary to integrate, into the antenna feed structure, a network of hybrid components, which would introduce significant losses. The CCWA embodies an alternate approach that entails relatively low losses and affords the additional advantage of compactness. The CCWA includes a circular cylindrical cup, a circular disk subreflector, and a circular waveguide that serves as the excitation element. The components that make it possible to obtain simultaneous dual circular polarization are integrated into the circular waveguide. These components are a sixpost polarizer and an orthomode transducer (OMT) with two orthogonal coaxial ports. The overall length of the OMT and polarizer (for the nominal middle design frequency of 2.25 GHz) is about 11 in. (approximately equal to 28 cm), whereas the length of a commercially available OMT and polarizer for the same frequency is about 32 in. (approximately equal to 81 cm).

  4. Interaction of a relativistic electron beam with radiation in the THz frequency range

    Science.gov (United States)

    Sung, Chieh

    The ability to generate a train of microbunches that are only typically tens of femtosecond wide and are separated by a picosecond is a topic of contemporary interest in the field of free electron lasers and plasma based accelerators. Moreover the usefulness of the high gradients present in plasma accelerators will depend on the ability to obtain mono-energetic relativistic electrons. This means that in addition to being prebunched on a scale shorter than the plasma wavelength the externally injected electron beam must be phase-locked to the accelerating plasma wave structure. In this thesis we investigate two techniques, Free Electron Laser interaction (FEL) and the Inverse Free Electron Laser interaction (IFEL), by which a medium energy electron beam can be prebunched into a series of microbunches with the same periodicity as a plasma wave and is phase locked to it. Using full-scale, 3-D simulations we show in this thesis that when a relativistic electron beam and an electromagnetic wave propagate collinearly through a magnetic undulator, FEL and IFEL interactions have the capability to form electron microbunches with periodicity 300-100 mum (1-3 THz range), which contain 50% of electrons within a small fraction of the ponderomotive buckets. Such a bunched beam is suitable for injection into plasma densities in the range 1016-1017 cm-3, respectively. Microbunching using the FEL mechanism requires a narrowband THz radiation source to act as a seed whereas the IFEL mechanism requires, in addition, such a source to be high power. In this thesis the generation of THz radiation in the Neptune Laboratory by mixing of two CO2 laser lines in a non-collinearly phase matched GaAs at room temperature is described A high-power THz pulse with up to 2 MW of peak power in a 250 ps pulse was generated using a TW class CO2 laser pulse. Such high power THz radiation is needed for the IFEL approach to microbunching. We also produced a high repetition rate THz source tunable in the

  5. Studies on the transmission of sub-THz waves in magnetized inhomogeneous plasma sheath

    Science.gov (United States)

    Yuan, Kai; Shen, Linfang; Yao, Ming; Deng, Xiaohua; Chen, Zhou; Hong, Lujun

    2018-01-01

    There have been many studies on the sub-terahertz (sub-THz) wave transmission in reentry plasma sheaths. However, only some of them have paid attention to the transmission of sub-THz waves in magnetized plasma sheaths. In this paper, the transmission of sub-THz waves in both unmagnetized and magnetized reentry plasma sheaths was investigated. The impacts of temporal evolution of the plasma sheath on the wave transmission were studied. The transmission of "atmospheric window" frequencies in a magnetized plasma sheath was discussed in detail. According to the study, the power transmission rates (Tp) for the left hand circular (LHC) and the right hand circular modes in the magnetized plasma sheath are obviously higher and lower than those in the unmagnetized plasma sheath, respectively. The Tp of LHC mode increases with both wave frequency and external magnetic field strength. Also, the Tp of LHC mode in both magnetized and unmagnetized plasma sheaths varies with time due to the temporal evolution of the plasma sheath. Moreover, the performance of sub-THz waves in magnetized plasma sheath hints at a new approach to the "blackout" problem. The new approach, which is in the capability of modern technology, is to utilize the communication system operating at 140 GHz with an onboard magnet installed near the antenna.

  6. Improvement of antenna decoupling in radar systems

    Science.gov (United States)

    Anchidin, Liliana; Topor, Raluca; Tamas, Razvan D.; Dumitrascu, Ana; Danisor, Alin; Berescu, Serban

    2015-02-01

    In this paper we present a type of antipodal Vivaldi antenna design, which can be used for pulse radiation in UWB communication. The Vivaldi antenna is a special tapered slot antenna with planar structure which is easily to be integrated with transmitting elements and receiving elements to form a compact structure. When the permittivity is very large, the wavelength of slot mode is so short that the electromagnetic fields concentrate in the slot to form an effective and balanced transmission line. Due to its simple structure and small size the Vivaldi antennas are one of the most popular designs used in UWB applications. However, for a two-antenna radar system, there is a high mutual coupling between two such antennas due to open configuration. In this paper, we propose a new method for reducing this effect. The method was validated by simulating a system of two Vivaldi antennas in front of a standard target.

  7. Steerable antenna and method for controlling said steerable antenna

    OpenAIRE

    Keshmiri, Farshad; Jha, Shambhu Nath; Drouguet, Maxime; Craeye, Christophe; Université catholique de Louvain

    2015-01-01

    Steerable antenna (1) comprising: a first antenna group comprising M antenna elements (5), a second antenna group comprising N antenna elements (5), said N antenna elements (5) surrounding the M antenna elements (5) of first antenna group, switching means (100) coupled to the N antenna elements (5) of second antenna group and a controller (110) programmed for sequentially switching to be active and at different times successive antenna subgroups of second antenna group, while switching at sam...

  8. THz waves: biological effects, industrial and medical

    International Nuclear Information System (INIS)

    Coutaz, J.L.; Garet, F.; Le Drean, Y.; Zhadobov, M.; Veyret, B.; Mounaix, P.; Caumes, J.P.; Gallot, G.; Gian Piero, Gallerano; Mouret, G.; Guilpin, J.C.

    2011-01-01

    Following the debates about body scanners installed in airports for passengers security control, the non-ionizing radiations (NIR) section of the French radiation protection society (SFR) has organized a conference day to take stock of the present day knowledge about the physical aspects and the biological effects of this frequency range as well as about their medical, and industrial applications (both civil and military). This document gathers the slides of the available presentations: 1 - introduction and general considerations about THz waves, the THz physical phenomenon among NIR (J.L. Coutaz); 2 - interaction of millimeter waves with living material: from dosimetry to biological impacts (Y. Le Drean and M. Zhadobov); 3 - Tera-Hertz: standards and recommendations (B. Veyret); 4 - THz spectro-imaging technique: status and perspectives (P. Mounaix); 5 - THz technology: seeing the invisible? (J.P. Caumes); 6 - Tera-Hertz: biological and medical applications (G. Gallot); 7 - Biological applications of THz radiation: a review of events and a glance to the future (G.P. Gallerano); 8 - Industrial and military applications - liquids and solids detection in the THz domain (F. Garet); 9 - THz radiation and its civil and military applications - gas detection and quantifying (G. Mouret); 10 - Body scanners and civil aviation security (J.C. Guilpin, presentation not available). (J.S.)

  9. A highly directive graphene antenna embedded inside a Fabry-Perot cavity in terahertz regime

    Science.gov (United States)

    Roshanaei, Majid; Karami, Hamidreza; Dehkhoda, Parisa; Esfahani, Hamid; Dabir, Fatemeh

    2018-05-01

    In this paper, a highly directive nano-thickness graphene-based antenna is introduced in the terahertz frequency band. The antenna is a graphene patch dipole which is placed between two Bragg mirrors called Fabry-Perot cavity. Tunability of the graphene's conductivity makes it possible to excite the desired resonances of the cavity. Here, first, a single resonant antenna is introduced at 5 THz with an enhanced gain from 2.11 dBi to 12.8 dBi with a beamwidth of 22.7°. Then, a triple resonant antenna at 4.7, 5 and 5.3 THz is presented with respective gains of 7.97, 11.9 and 8.52 dBi. Finally, the effect of dimensions and number of the dielectric layers of the cavity are studied in order to further increase in directivity.

  10. 47 CFR 17.9 - Designated antenna farm areas.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Designated antenna farm areas. 17.9 Section 17... ANTENNA STRUCTURES Federal Aviation Administration Notification Criteria § 17.9 Designated antenna farm areas. The areas described in the following paragraphs of this section are established as antenna farm...

  11. 47 CFR 17.8 - Establishment of antenna farm areas.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Establishment of antenna farm areas. 17.8... LIGHTING OF ANTENNA STRUCTURES Federal Aviation Administration Notification Criteria § 17.8 Establishment of antenna farm areas. (a) Each antenna farm area will be established by an appropriate rulemaking...

  12. Ultra-broadband THz time-domain spectroscopy of common polymers using THz air photonics

    DEFF Research Database (Denmark)

    D’Angelo, Francesco; Mics, Zoltán; Bonn, Mischa

    2014-01-01

    Terahertz-range dielectric properties of the common polymers low-density polyethylene (LDPE), cyclic olefin/ethylene copolymer (TOPAS®), polyamide-6 (PA6), and polytetrafluoroethylene (PTFE or Teflon®) are characterized in the ultra-broadband frequency window 2-15 THz, using a THz time-domain spe......Terahertz-range dielectric properties of the common polymers low-density polyethylene (LDPE), cyclic olefin/ethylene copolymer (TOPAS®), polyamide-6 (PA6), and polytetrafluoroethylene (PTFE or Teflon®) are characterized in the ultra-broadband frequency window 2-15 THz, using a THz time...... and PTFE, and their dielectric functions in the complete frequency window 2-15 THz are theoretically reproduced. Our results demonstrate the potential of ultrabroadband air-photonics-based THz time domain spectroscopy as a valuable analytic tool for materials science....

  13. Rigidized Inflatable Veritex(TM) Structured For RF Antennas, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Cornerstone Research Group inc. (CRG) proposes to demonstrate the feasibility of a lightweight, deployable Veritex TM supporting annulus structure to support large...

  14. Chemical recognition with broadband THz spectroscopy

    DEFF Research Database (Denmark)

    Fischer, Bernd M.; Helm, Hanspeter; Jepsen, Peter Uhd

    2004-01-01

    contains unique fingerprints of a very large number of crystalline materials, including explosives, illicit drugs as well as most other chemicals in powder form. Since many packaging materials are transparent to THz radiation this fundamental property of crystalline compounds allows remote (contact...... with broadband THz spectroscopy. Amorphous systems of great biotechnical importance include DNA and proteins, both in aqueous solution and as dried matter. We will discuss methods for THz science and technology to attack the very complex problems involved in the extraction of useful new information which may...

  15. Polymer microstructured fibers for guiding of THz radiation

    DEFF Research Database (Denmark)

    Nielsen, Kristian; Bang, Ole; Jepsen, Peter Uhd

    2010-01-01

    spectroscopic investigations of minute sample quantities [3]. In this presentation we will describe our current efforts in the development, fabrication and characterization of a class of THz waveguides and components based on microstructured polymer optical fibers (mPOF’s) [4] designed for the THz frequency...... range [5]. Fabrication and characterization of tailored mPOF’s Similar to photonic crystal fibers for the near-infrared, we fabricate our mPOF structures in a fiber draw tower. Based on numerical simulations, a fiber cross section is first designed using standard and custom finite-element methods...... and FDTD methods, and based on the design, a preform is drilled in a low-loss polymer preform. This preform is heated to above the glass transition temperature of the polymer, and the preform is drawn to the desired dimensions in a single manufacturing step. Optical characterization of the fabricated...

  16. Continuous terahertz-wave generation using a monolithically integrated horn antenna

    Science.gov (United States)

    Peytavit, E.; Beck, A.; Akalin, T.; Lampin, J.-F.; Hindle, F.; Yang, C.; Mouret, G.

    2008-09-01

    A transverse electromagnetic horn antenna is monolithically integrated with a standard ultrafast interdigitated electrode photodetector on low-temperature-grown GaAs. Continuous-wave terahertz radiation is generated at frequencies up to 2 THz with a maximum power of approximately 1 μW at 780 GHz. Experimental variations in the terahertz power as function of the frequency are explained by means of electromagnetic simulations of the antenna and the photomixer vicinity.

  17. THz absorption signature detection of genetic material of E. coli and B. subtilis

    Science.gov (United States)

    Bykhovski, Alexei; Li, Xiaowei; Globus, Tatiana; Khromova, Tatyana; Gelmont, Boris; Woolard, Dwight; Samuels, Alan C.; Jensen, James O.

    2005-11-01

    The development of efficient biological agent detection techniques requires in-depth understanding of THz absorption spectral features of different cell components. Chromosomal DNA, RNAs, proteins, bacterial cell wall, proteinaceous coat might be essential for bacterial cells and spores THz signature. As a first step, the DNA's contribution into entire cell THz spectra was analyzed. The experimental study of cells and DNAs of E. coli and cells/spores and DNA of Bacillus subtilis was conducted. Samples were prepared in the form of water solutions (suspension) with the concentrations in the range 0.01-1 mg/ml. The measurable difference in the THz transmission spectra of E. coli and Bacillus subtilis DNAs was observed. The correlation between chromosomal DNA signature and a corresponding entire spore/cell signature was observed. This correlation was especially pronounced for spores of Bacillus subtilis and their DNA. These experimental results justify our approach to develop a model for THz signatures of biological simulants and agents. In parallel with the experimental study, for the first time, the computer modeling and simulation of chromosome DNAs of E. coli and Bacillus subtilis was performed and their THz signatures were calculated. The DNA structures were optimized using the Amber software package. Also, we developed the initial model of the DNA fragment poly(dAT)-poly(dTA) solvated in water to be used in the simulations of genetic material (DNA and RNA) of spores and cells. Molecular dynamical simulations were conducted using explicit solvent (3-point TIP3P water) and implicit solvent (generalized Born) models. The calculated THz signatures of E. coli and Bacillus subtilis DNAs and poly(dAT)-poly(dTA) reproduce many features of our measured spectra. The results of this study demonstrate that THz Fourier transform infrared spectroscopy is a promising tool in generating spectral data for complex biological objects such as bacterial cells and spores.

  18. Transmission of reactive pulsed laser deposited VO{sub 2} films in the THz domain

    Energy Technology Data Exchange (ETDEWEB)

    Émond, Nicolas; Hendaoui, Ali; Ibrahim, Akram; Al-Naib, Ibraheem; Ozaki, Tsuneyuki; Chaker, Mohamed, E-mail: chaker@emt.inrs.ca

    2016-08-30

    Highlights: • Synthesis of vanadium dioxide (VO{sub 2}) thin films as a function of oxygen pressure (2–25 mTorr) using Reactive Pulsed Laser Deposition (RPLD). • Characterization of RPLD-grown VO{sub 2} thin films in the THz frequency range. • THz switches and/or sensors require VO{sub 2} films deposited at low oxygen pressure (i.e. low transition temperature, large amplitude contrast of THz transmission, narrow hysteresis width). • THz optical memory applications require VO{sub 2} films deposited at high oxygen pressure (broad hysteresis width). - Abstract: This work reports on the characteristics of the insulator-to-metal transition (IMT) of reactive pulsed laser deposited vanadium dioxide (VO{sub 2}) films in the terahertz (THz) frequency range, namely the transition temperature T{sub IMT}, the amplitude contrast of the THz transmission over the IMT ΔA, the transition sharpness ΔT and the hysteresis width ΔH. XRD analysis shows the sole formation of VO{sub 2} monoclinic structure with an enhancement of (011) preferential orientation when varying the O{sub 2} pressure (P{sub O2}) during the deposition process from 2 to 25 mTorr. THz transmission measurements as a function of temperature reveal that VO{sub 2} films obtained at low P{sub O2} exhibit low T{sub IMT}, large ΔA, and narrow ΔH. Increasing P{sub O2} results in VO{sub 2} films with higher T{sub IMT}, smaller ΔA, broader ΔH and asymmetric hysteresis loop. The good control of the VO{sub 2} IMT features in the THz domain could be further exploited for the development of advanced smart devices, such as ultrafast switches, modulators, memories and sensors.

  19. Intersubband spontaneous emission from GaN-based THz quantum cascade laser

    Science.gov (United States)

    Terashima, W.; Hirayama, H.

    2013-03-01

    We studied on terahertz-quantum cascade lasers (THz-QCLs) using III-Nitride semiconductors, which are promising materials for the realization of the unexplored frequency range from 5 to 12 THz and the higher temperature operation on THz-QCLs, because these compounds have much larger longitudinal optical phonon energies (> 18 THz) than those of conventional GaAs-based materials (~ 9 THz). Firstly, we showed clearly that it is possible to design a GaN-based quantum cascade (QC) structure which operates in the THz range in which population inversion can be obtained, by performing numerical calculations based on a self-consistent rate equation model. Secondly, we succeeded in the stack of QC structure with a large number of periods and the drastic improvement of structural properties of QC structure, by introducing a new growth technique named "a droplet elimination by thermal annealing (DETA)" in which utilized the differences of the properties between metals (Al, Ga) and Nitrides (AlN, GaN) into molecular beam epitaxy. Finally, we for the first time successfully observed spontaneous electroluminescence due to intersubband transitions with peaks at frequencies from 1.4 to 2.8 THz from GaN/AlGaN QCL devices fabricated with using the DETA technique grown on a GaN substrate and a metal organic chemical vapor deposition (MOCVD)-AlN template on a sapphire substrate. In this paper, we demonstrate recent achievements on the quantum design, fabrication technique, and electroluminescence properties of GaN-based QCL structures.

  20. Low-Loss NbTiN Films for THz SIS Mixer Tuning Circuits

    Science.gov (United States)

    Kooi, J. W.; Stern, J. A.; Chattopadhyay, G.; LeDuc, H. G.; Bumble, B.; Zmuidzinas, J.

    1998-01-01

    Recent results at 1 THz using normal-metal tuning circuits have shown that SIS mixers can work well up to twice the gap frequency of the junction material (niobium). However, the performance at 1 THz is limited by the substantial loss in the normal metal films. For better performance superconducting films with a higher gap frequency than niobium and with low RF loss are needed. Niobium nitride has long been considered a good candidate material, but typical NbN films suffer from high RF loss. To circumvent this problem we are currently investigating the RF loss in NbTiN films, a 15 K Tc compound superconductor, by incorporating them into quasi-optical slot antenna SIS devices.

  1. Recent progress toward realizing GaN-based THz quantum cascade laser

    Science.gov (United States)

    Hirayama, H.; Terashima, W.

    2013-12-01

    We are studying on terahertz-quantum cascade lasers (THz-QCLs) using III-nitride semiconductor, which is a material having potentials for realizing wide frequency range of QCL, i.e., 1-15 THz and 1-10 μm, including an unexplored terahertz frequency range from 5 to 12 THz. GaN-based QCLs also have potential to realize room temperature operation of THz-QCL. The merit of using an AlGaN-based semiconductor in comparison with GaAs or InP is that it has much higher longitudinal optical phonon energies (ELO) (> 90meV) than those of conventional GaAs-based materials (~ 36 meV). We designed a GaN/AlGaN QCL that can operates in THz frequency range, and fabricated the GaN/AlGaN QCL devices by using molecular beam epitaxy (MBE). We demonstrated dramatic improvement of structural properties of QC stacking layers by introducing a novel growth technique "a droplet elimination by thermal annealing (DETA) method". We have observed inter-subband spontaneous emissions under current injection with peak frequencies from 1.4 to 2.8 THz from GaN/AlGaN QCL devices. The intensity of the emission was much improved by fabricating them on a low threading dislocation density (TDD) AlN/AlGaN template prepared by metal-organic chemical-vapor epitaxy (MOCVD) on a sapphire substrate.

  2. THz-driven demagnetization with perpendicular magnetic anisotropy: towards ultrafast ballistic switching

    Science.gov (United States)

    Polley, Debanjan; Pancaldi, Matteo; Hudl, Matthias; Vavassori, Paolo; Urazhdin, Sergei; Bonetti, Stefano

    2018-02-01

    We study THz-driven spin dynamics in thin CoPt films with perpendicular magnetic anisotropy. Femtosecond magneto-optical Kerr effect measurements show that demagnetization amplitude of about 1% can be achieved with a peak THz electric field of 300 kV cm‑1, and a corresponding peak magnetic field of 0.1 T. The effect is more than an order of magnitude larger than observed in samples with easy-plane anisotropy irradiated with the same field strength. We also utilize finite-element simulations to design a meta-material structure that can enhance the THz magnetic field by more than an order of magnitude, over an area of several tens of square micrometers. Magnetic fields exceeding 1 Tesla, generated in such meta-materials with the available laser-based THz sources, are expected to produce full magnetization reversal via ultrafast ballistic precession driven by the THz radiation. Our results demonstrate the possibility of table-top ultrafast magnetization reversal induced by THz radiation.

  3. The impact of hydration changes in fresh bio-tissue on THz spectroscopic measurements

    Science.gov (United States)

    Png, G. M.; Choi, J. W.; W-H Ng, B.; Mickan, S. P.; Abbott, D.; Zhang, X.-C.

    2008-07-01

    We present a study of how residual hydration in fresh rat tissue samples can vastly alter their extracted terahertz (THz) optical properties and influence their health assessment. Fresh (as opposed to preserved) tissue most closely mimics in vivo conditions, but high water content creates many challenges for tissue handling and THz measurement. Our THz measurements of fresh tissue over time highlight the effect of tissue hydration on tissue texture and dimension, the latter directly influencing the accuracy of calculated optical properties. We then introduce lyophilization (freeze drying) as a viable solution for overcoming hydration and freshness problems. Lyophilization removes large amounts of water while retaining sample freshness. In addition, lyophilized tissue samples are easy to handle and their textures and dimensions do not vary over time, allowing for consistent and stable THz measurements. A comparison of lyophilized and fresh tissue shows for the first time that freeze drying may be one way of overcoming tissue hydration issues while preserving tissue cellular structure. Finally, we compare THz measurements from fresh tissue against necrotic tissue to verify freshness over time. Indeed, THz measurements from fresh and necrotic tissues show marked differences.

  4. The impact of hydration changes in fresh bio-tissue on THz spectroscopic measurements

    International Nuclear Information System (INIS)

    Png, G M; Ng, B W-H; Mickan, S P; Abbott, D; Choi, J W; Zhang, X-C

    2008-01-01

    We present a study of how residual hydration in fresh rat tissue samples can vastly alter their extracted terahertz (THz) optical properties and influence their health assessment. Fresh (as opposed to preserved) tissue most closely mimics in vivo conditions, but high water content creates many challenges for tissue handling and THz measurement. Our THz measurements of fresh tissue over time highlight the effect of tissue hydration on tissue texture and dimension, the latter directly influencing the accuracy of calculated optical properties. We then introduce lyophilization (freeze drying) as a viable solution for overcoming hydration and freshness problems. Lyophilization removes large amounts of water while retaining sample freshness. In addition, lyophilized tissue samples are easy to handle and their textures and dimensions do not vary over time, allowing for consistent and stable THz measurements. A comparison of lyophilized and fresh tissue shows for the first time that freeze drying may be one way of overcoming tissue hydration issues while preserving tissue cellular structure. Finally, we compare THz measurements from fresh tissue against necrotic tissue to verify freshness over time. Indeed, THz measurements from fresh and necrotic tissues show marked differences

  5. Forward Scattering of Loaded and Unloaded Antennas

    DEFF Research Database (Denmark)

    Gustafsson, Mats; Andersen, Jørgen Bach; Kristensson, Gerhard

    2012-01-01

    Forward scattering of antennas is related to antenna performance via the forward-scattering sum rule. The forward-scattering sum rule is an integral identity that shows that a weighted integral of the extinction cross section over all spectrum is proportional to the static polarizability...... of the antenna structure. Here, the forward-scattering sum rule is experimentally verified for loaded, short-circuit, and open-circuit cylindrical dipole antennas. It is also shown that the absorption efficiency cannot be greater than 1/2 for reciprocal linearly polarized lossless matched antennas...... with a symmetric radiation pattern in the forward and backward directions....

  6. Dual Band Notched EBG Structure based UWB MIMO/Diversity Antenna with Reduced Wide Band Electromagnetic Coupling

    Science.gov (United States)

    Jaglan, Naveen; Kanaujia, Binod Kumar; Gupta, Samir Dev; Srivastava, Shweta

    2017-10-01

    A dual band-notched MIMO/Diversity antenna is proposed in this paper. The proposed antenna ensures notches in WiMAX band (3.3-3.6 GHz) besides WLAN band (5-6 GHz). Mushroom Electromagnetic Band Gap (EBG) arrangements are employed for discarding interfering frequencies. The procedure followed to attain notches is antenna shape independent with established formulas. The electromagnetic coupling among two narrowly set apart Ultra-Wide Band (UWB) monopoles is reduced by means of decoupling bands and slotted ground plane. Monopoles are 90° angularly parted with steps on the radiator. This aids to diminish mutual coupling and also adds in the direction of impedance matching by long current route. S21 or else mutual coupling of fewer than 15 dB is established over antenna operating range. Two-port envelope correlation coefficient is lower than 0.02 in UWB range of 3.1 GHz-10.6 GHz. The shifting in notch frequencies by varying variables in formulas is also reported. The suggested antenna is designed on low budget FR-4 substrate with measurements as (58 × 45 × 1.6) mm3. Simulated and measured results of fabricated antenna are found to be in close agreement.

  7. Superluminal antenna

    Energy Technology Data Exchange (ETDEWEB)

    Singleton, John; Earley, Lawrence M.; Krawczyk, Frank L.; Potter, James M.; Romero, William P.; Wang, Zhi-Fu

    2018-04-17

    A superluminal antenna element integrates a balun element to better impedance match an input cable or waveguide to a dielectric radiator element, thus preventing stray reflections and consequent undesirable radiation. For example, a dielectric housing material can be used that has a cutout area. A cable can extend into the cutout area. A triangular conductor can function as an impedance transition. An additional cylindrical element functions as a sleeve balun to better impedance match the radiator element to the cable.

  8. Superluminal antenna

    Science.gov (United States)

    Singleton, John; Earley, Lawrence M.; Krawczyk, Frank L.; Potter, James M.; Romero, William P.; Wang, Zhi-Fu

    2017-03-28

    A superluminal antenna element integrates a balun element to better impedance match an input cable or waveguide to a dielectric radiator element, thus preventing stray reflections and consequent undesirable radiation. For example, a dielectric housing material can be used that has a cutout area. A cable can extend into the cutout area. A triangular conductor can function as an impedance transition. An additional cylindrical element functions as a sleeve balun to better impedance match the radiator element to the cable.

  9. Emission of coherent THz radiation from superconductors.

    Science.gov (United States)

    Ozyuzer, L; Koshelev, A E; Kurter, C; Gopalsami, N; Li, Q; Tachiki, M; Kadowaki, K; Yamamoto, T; Minami, H; Yamaguchi, H; Tachiki, T; Gray, K E; Kwok, W-K; Welp, U

    2007-11-23

    Compact solid-state sources of terahertz (THz) radiation are being sought for sensing, imaging, and spectroscopy applications across the physical and biological sciences. We demonstrate that coherent continuous-wave THz radiation of sizable power can be extracted from intrinsic Josephson junctions in the layered high-temperature superconductor Bi2Sr2CaCu2O8. In analogy to a laser cavity, the excitation of an electromagnetic cavity resonance inside the sample generates a macroscopic coherent state in which a large number of junctions are synchronized to oscillate in phase. The emission power is found to increase as the square of the number of junctions reaching values of 0.5 microwatt at frequencies up to 0.85 THz, and persists up to approximately 50 kelvin. These results should stimulate the development of superconducting compact sources of THz radiation.

  10. On diversity performance of two-element coupling element based antenna structure for mobile terminal

    DEFF Research Database (Denmark)

    Al-Hadi, Azremi Abdullah; Toivanen, Juha; Laitinen, Tommi

    2010-01-01

    for low frequency diversity application with stable and low envelope correlation across wide frequency range. The studied structure has been tuned to be operating at 1600 MHz for measurement evaluation purpose. This paper presents an analysis of diversity performance of the structure in terms...... of efficiencies, envelope correlation, and apparent and effective diversity gains in isotropic (i.e. statistically uniform) propagation channel, using spherical near-field technique in an ideal line-of-sight environment (anechoic chamber) and inside reverberation chamber. The envelope correlation is less than 0...

  11. Hex-Sided Rounded Dipole Antenna (HSRDA) For UWB Applications

    Science.gov (United States)

    Singhal, Sarthak; Verma, Nand Kishor; Singh, Amit Kumar

    2016-03-01

    A hex-sided rounded dipole antenna (HSRDA) for UWB applications is presented. It is designed by the addition of semi-elliptical patch sections at the edges of a square bow-tie antenna. The antenna structure is fed by a modified microstrip feedline for better impedance matching. An impedance bandwidth of 2.9-11.4 GHz is achieved. The antenna structure has quasi omnidirectional radiation patterns and reasonable gain over the same frequency range. A good agreement between the experimental and simulation results is observed. The proposed antenna structure has miniaturized size for the same bandwidth as compared to already reported antenna structures.

  12. Moths smell with their antennae

    Science.gov (United States)

    Spencer, Thomas; Ballard, Matthew; Alexeev, Alexander; Hu, David

    2015-11-01

    Moths are reported to smell each other from over 6 miles away, locating each other with just 200 airborne molecules. In this study, we investigate how the structure of the antennae influences particle capture. We measure the branching patterns of over 40 species of moths, across two orders of magnitude in weight. We find that moth antennae have 3 levels of hierarchy, with dimensions on each level scaling with body size. We perform lattice-Boltzman simulations to determine optimal flow patterns around antennae branches allowing for capture of small particles.

  13. Antenna-coupled terahertz radiation from joule-heated single-wall carbon nanotubes

    Directory of Open Access Journals (Sweden)

    M. Muthee

    2011-12-01

    Full Text Available In this letter an experimental method is introduced that allows detection of terahertz (THz radiation from arrays of joule-heated Single-Walled Carbon Nanotubes (SWCNTs, by coupling this radiation through integrated antennas and a silicon lens. The radiation forms a diffraction-limited beam with a total maximum radiated power of 450 nW, significantly greater than the power estimated from Nyquist thermal noise (8 nW. The physical radiation process is unknown at this stage, but possible explanations for the high radiated power are discussed briefly. The emission has a typical bandwidth of 1.2 THz and can be tuned to different frequencies by changing the dimensions of the antennas. Arrays of the devices could be integrated in CMOS integrated circuits, and find application in THz systems, such as in near-range medical imaging.

  14. Design and verification of monopole patch antenna systems to generate orbital angular momentum waves

    OpenAIRE

    Dandan Liu; Liangqi Gui; Cong Zhou; Zixiao Zhang; Han Chen; Tao Jiang

    2017-01-01

    Monopole patch antenna systems, which can generate orbital angular momentum (OAM) waves at 2.4GHz, are proposed in this paper. The proposed antenna systems have advantages of simple planar structure and small size of antenna element. Design, simulation, fabrication and measurement of the proposed antenna systems are presented. Two feeding networks, which constitute the proposed antenna systems with monopole patch antenna array, are designed to generate modes 1 and 2 of OAM waves. The antenna ...

  15. Conformal Load-Bearing Antenna Structure for Australian Defence Force Aircraft

    Science.gov (United States)

    2007-03-01

    conventional capacitors are required to store 1 MJ. A potential alternative is the structural capacitor , where energy is stored in coated wires that are woven... capacitors if they were incorporated into the wings and fuselage of an aircraft. Armour Intuitively it should be relatively straightforward to...and Control (AEW&C), the radar disc on the E- 3 Airborne Warning and Control System (AWACS) or the bulging nose on the RQ-4 Global Hawk. It is clear

  16. A Low-Noise CMOS THz Imager Based on Source Modulation and an In-Pixel High-Q Passive Switched-Capacitor N-Path Filter.

    Science.gov (United States)

    Boukhayma, Assim; Dupret, Antoine; Rostaing, Jean-Pierre; Enz, Christian

    2016-03-03

    This paper presents the first low noise complementary metal oxide semiconductor (CMOS) deletedCMOS terahertz (THz) imager based on source modulation and in-pixel high-Q filtering. The 31 × 31 focal plane array has been fully integrated in a 0 . 13 μ m standard CMOS process. The sensitivity has been improved significantly by modulating the active THz source that lights the scene and performing on-chip high-Q filtering. Each pixel encompass a broadband bow tie antenna coupled to an N-type metal-oxide-semiconductor (NMOS) detector that shifts the THz radiation, a low noise adjustable gain amplifier and a high-Q filter centered at the modulation frequency. The filter is based on a passive switched-capacitor (SC) N-path filter combined with a continuous-time broad-band Gm-C filter. A simplified analysis that helps in designing and tuning the passive SC N-path filter is provided. The characterization of the readout chain shows that a Q factor of 100 has been achieved for the filter with a good matching between the analytical calculation and the measurement results. An input-referred noise of 0 . 2 μ V RMS has been measured. Characterization of the chip with different THz wavelengths confirms the broadband feature of the antenna and shows that this THz imager reaches a total noise equivalent power of 0 . 6 nW at 270 GHz and 0 . 8 nW at 600 GHz.

  17. 120 Gb/s Multi-Channel THz Wireless Transmission and THz Receiver Performance Analysis

    DEFF Research Database (Denmark)

    Jia, Shi; Yu, Xianbin; Hu, Hao

    2017-01-01

    A photonic multi-channel terahertz (THz) wireless transmission system in the 350-475 GHz band is experimentally demonstrated. The employment of six THz carriers modulated with 10 Gbaud Nyquist quadrature phase-shift keying baseband signal per carrier results in an overall capacity of up to 120 Gb...

  18. Real and limit sensitivity of some radiation detectors of THz/sub-THz ranges

    Directory of Open Access Journals (Sweden)

    Shevchik-Shekera A. V.

    2012-02-01

    Full Text Available It is shown that while calculating the NEP parameter of radiation detectors of THz/sub-THz range, the fluctuations of the background radiation flux at different temperatures of the background in the case of diffraction-limited beam should be taken into account.

  19. THz and mid-IR spectroscopy of interstellar ice analogs: methyl and carboxylic acid groups.

    Science.gov (United States)

    Ioppolo, S; McGuire, B A; Allodi, M A; Blake, G A

    2014-01-01

    A fundamental problem in astrochemistry concerns the synthesis and survival of complex organic molecules (COMs) throughout the process of star and planet formation. While it is generally accepted that most complex molecules and prebiotic species form in the solid phase on icy grain particles, a complete understanding of the formation pathways is still largely lacking. To take full advantage of the enormous number of available THz observations (e.g., Herschel Space Observatory, SOFIA, and ALMA), laboratory analogs must be studied systematically. Here, we present the THz (0.3-7.5 THz; 10-250 cm(-1)) and mid-IR (400-4000 cm(-1)) spectra of astrophysically-relevant species that share the same functional groups, including formic acid (HCOOH) and acetic acid (CH3COOH), and acetaldehyde (CH3CHO) and acetone ((CH3)2CO), compared to more abundant interstellar molecules such as water (H2O), methanol (CH3OH), and carbon monoxide (CO). A suite of pure and mixed binary ices are discussed. The effects on the spectra due to the composition and the structure of the ice at different temperatures are shown. Our results demonstrate that THz spectra are sensitive to reversible and irreversible transformations within the ice caused by thermal processing, suggesting that THz spectra can be used to study the composition, structure, and thermal history of interstellar ices. Moreover, the THz spectrum of an individual species depends on the functional group(s) within that molecule. Thus, future THz studies of different functional groups will help in characterizing the chemistry and physics of the interstellar medium (ISM).

  20. Distributed control of large space antennas

    Science.gov (United States)

    Cameron, J. M.; Hamidi, M.; Lin, Y. H.; Wang, S. J.

    1983-01-01

    A systematic way to choose control design parameters and to evaluate performance for large space antennas is presented. The structural dynamics and control properties for a Hoop and Column Antenna and a Wrap-Rib Antenna are characterized. Some results of the effects of model parameter uncertainties to the stability, surface accuracy, and pointing errors are presented. Critical dynamics and control problems for these antenna configurations are identified and potential solutions are discussed. It was concluded that structural uncertainties and model error can cause serious performance deterioration and can even destabilize the controllers. For the hoop and column antenna, large hoop and long meat and the lack of stiffness between the two substructures result in low structural frequencies. Performance can be improved if this design can be strengthened. The two-site control system is more robust than either single-site control systems for the hoop and column antenna.

  1. Antennas in inhomogeneous media

    CERN Document Server

    Galejs, Janis; Fock, V A; Wait, J R

    2013-01-01

    Antennas in Inhomogeneous Media details the methods of analyzing antennas in such inhomogeneous media. The title covers the complex geometrical configurations along with its variational formulations. The coverage of the text includes various conditions the antennas are subjected to, such as antennas in the interface between two media; antennas in compressible isotropic plasma; and linear antennas in a magnetoionic medium. The selection also covers insulated loops in lossy media; slot antennas with a stratified dielectric or isotropic plasma layers; and cavity-backed slot antennas. The book wil

  2. 47 CFR 73.812 - Rounding of power and antenna heights.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Rounding of power and antenna heights. 73.812... RADIO BROADCAST SERVICES Low Power FM Broadcast Stations (LPFM) § 73.812 Rounding of power and antenna...) Antenna radiation center, antenna height above average terrain (HAAT), and antenna supporting structure...

  3. Nano Antenna Integrated Diode (Rectenna) For Infrared Energy Harvesting

    KAUST Repository

    Gadalla, Mena N.

    2013-01-01

    In this work full parametric analysis of nano antennas is presented. To begin with, optical or electronic properties of noble metals such as gold and copper were studied in details to get a clear understanding of their reaction to an incident electromagnetic wave. Complex frequency dependent dielectric functions indicated that in THz metals acts as a dielectric with significant absorption. Simultaneous optimization of the length and the bow angle of a bow-tie antenna resulted in relative electric field intensity enhancement of 8 orders of magnitude for 0.5nm gap and 4 orders of magnitude for 50nm around 28THz resonance frequency. These results are at least 2 orders of magnitude greater than the published optical antennas. Physical reasons behind field localization and intensity enhancement  are  discussed  in  details.  The  solution  of  Maxwell’s  equations  at   the  interface   between metallic nano antenna and air is also present in this piece of research. The derived dispersion relation of surface plasmons shows momentum matching at 28.3 THz between free propagating electromagnetic fields’ modes in air and localized modes at the interface. Consequently, Propagating electromagnetic waves are ensured to couple to localized surface propagating modes producing filed enhancement. The integrated matching section is theoretically proven to increase transmission to substrate to 75% (compared to 40% without it) which in turn improves the coupled power by 40 times. Nano antennas were fabricated in house using Electron beam lithography with a precise gap of 50nm. In addition, THz diode was designed, fabricated and integrated to the nano antennas to rectify the enhanced THz signal. The integration of the nano diode required a precise overlap of the two arms of the antenna in the rage of 100nm. In order to overcome two arms overlap fabrication challenges, three layer alignment technique was used to produce precise overlap.The THz rectifier was

  4. Photo-conductive detection of continuous THz waves via manipulated ultrafast process in nanostructures

    Science.gov (United States)

    Moon, Kiwon; Lee, Eui Su; Lee, Il-Min; Park, Dong Woo; Park, Kyung Hyun

    2018-01-01

    Time-domain and frequency-domain terahertz (THz) spectroscopy systems often use materials fabricated with exotic and expensive methods that intentionally introduce defects to meet short carrier lifetime requirements. In this study, we demonstrate the development of a nano-photomixer that meets response speed requirements without using defect-incorporated, low-temperature-grown (LTG) semiconductors. Instead, we utilized a thin InGaAs layer grown on a semi-insulating InP substrate by metal-organic chemical vapor deposition (MOCVD) combined with nano-electrodes to manipulate local ultrafast photo-carrier dynamics via a carefully designed field-enhancement and plasmon effect. The developed nano-structured photomixer can detect continuous-wave THz radiation up to a frequency of 2 THz with a peak carrier collection efficiency of 5%, which is approximately 10 times better than the reference efficiency of 0.4%. The better efficiency results from the high carrier mobility of the MOCVD-grown InGaAs thin layer with the coincidence of near-field and plasmon-field distributions in the nano-structure. Our result not only provides a generally applicable methodology for manipulating ultrafast carrier dynamics by means of nano-photonic techniques to break the trade-off relation between the carrier lifetime and mobility in typical LTG semiconductors but also contributes to mass-producible photo-conductive THz detectors to facilitate the widespread application of THz technology.

  5. THz near-field imaging of biological tissues employing synchrotron radiation

    International Nuclear Information System (INIS)

    Schade, Ulrich; Holldack, Karsten; Martin, Michael C.; Fried, Daniel

    2004-01-01

    Terahertz scanning near-field infrared microscopy (SNIM) below 1 THz is demonstrated. The near-field technique benefits from the broadband and highly brilliant coherent synchrotron radiation (CSR) from an electron storage ring and from a detection method based on locking onto the intrinsic time structure of the synchrotron radiation. The scanning microscope utilizes conical wave guides as near-field probes with apertures smaller than the wavelength. Different cone approaches have been investigated to obtain maximum transmittance. Together with a Martin-Puplett spectrometer the set-up enables spectroscopic mapping of the transmittance of samples well below the diffraction limit. Spatial resolution down to about lambda/40 at 2 wavenumbers (0.06 THz) is derived from the transmittance spectra of the near-field probes. The potential of the technique is exemplified by imaging biological samples. Strongly absorbing living leaves have been imaged in transmittance with a spatial resolution of 130 mu-m at about 12 wave numbers (0.36 THz). The THz near-field images reveal distinct structural differences of leaves from different plants investigated. The technique presented also allows spectral imaging of bulky organic tissues. Human teeth samples of various thicknesses have been imaged between 2 and 20 wavenumbers (between 0.06and 0.6 THz). Regions of enamel and dentin within tooth samples are spatially and spectrally resolved, and buried caries lesions are imaged through both the outer enamel and into the underlying dentin

  6. Quasi-analytical synthesis of continuous phase correcting structures to increase the directivity of circularly polarized Fabry-Perot resonator antennas

    International Nuclear Information System (INIS)

    Afzal, Muhammad U.; Esselle, Karu P.

    2015-01-01

    This paper presents a quasi-analytical technique to design a continuous, all-dielectric phase correcting structures (PCSs) for circularly polarized Fabry-Perot resonator antennas (FPRAs). The PCS has been realized by varying the thickness of a rotationally symmetric dielectric block placed above the antenna. A global analytical expression is derived for the PCS thickness profile, which is required to achieve nearly uniform phase distribution at the output of the PCS, despite the non-uniform phase distribution at its input. An alternative piecewise technique based on spline interpolation is also explored to design a PCS. It is shown from both far- and near-field results that a PCS tremendously improves the radiation performance of the FPRA. These improvements include an increase in peak directivity from 22 to 120 (from 13.4 dBic to 20.8 dBic) and a decrease of 3 dB beamwidth from 41.5° to 15°. The phase-corrected antenna also has a good directivity bandwidth of 1.3 GHz, which is 11% of the center frequency

  7. Antenna design by simulation-driven optimization

    CERN Document Server

    Koziel, Slawomir

    2014-01-01

    This Brief reviews a number of techniques exploiting the surrogate-based optimization concept and variable-fidelity EM simulations for efficient optimization of antenna structures. The introduction of each method is illustrated with examples of antenna design. The authors demonstrate the ways in which practitioners can obtain an optimized antenna design at the computational cost corresponding to a few high-fidelity EM simulations of the antenna structure. There is also a discussion of the selection of antenna model fidelity and its influence on performance of the surrogate-based design process. This volume is suitable for electrical engineers in academia as well as industry, antenna designers and engineers dealing with computationally-expensive design problems.

  8. A European Project on Vacuum Tube Amplifiers for THz Amplification

    DEFF Research Database (Denmark)

    Paoloni, Claudio; Di Carlo, Aldo; Brunetti, Francesca

    2012-01-01

    The OPTHER (Optically Driven THz amplifier) project supported by the European Commission within the Seventh Framework Program (FP7) represents the first joint European attempt to realize vacuum electron devices in THz range. The target of the project was to design and realize the first 1 THz vacuum...

  9. THz Electro-absorption Effect in Quantum Dots

    DEFF Research Database (Denmark)

    Turchinovich, Dmitry; Monozon, Boris S.; Livshits, Daniil A.

    2011-01-01

    In a THz pump - optical probe experiment we demonstrate an instantaneous electro-absorption effect in InGaAs/GaAs quantum dots, induced by the electric field of a single-cycle THz pulse with 3 THz bandwidth and with free-space peak electric field reaching 220 kV/cm. The transient modulation of QD...

  10. THz spectroscopy of liquids – applications and future challenges

    DEFF Research Database (Denmark)

    Jepsen, Peter Uhd; Cooke, David; Møller, Uffe

    2009-01-01

    THz time-domain spectroscopy (THz-TDS) is by now getting an established technique for the precise determination of the dielectric function of various materials in the terahertz spectral range of the electromagnetic spectrum. Typically, THz-TDS is carried out using planar samples. Examples include...

  11. Towards Ultrahigh Speed Impulse Radio THz Wireless Communications

    DEFF Research Database (Denmark)

    Yu, Xianbin; Galili, Michael; Morioka, Toshio

    2015-01-01

    THz impulse radio technologies promise a new paradigm of fast wireless access with simplified wireless reception. However, huge loss of propagating broad bandwidth THz impulse radio signals limits THz wireless transmission distance and reduces the achievable link data rates. In this paper, we...

  12. Ultrabroadband THz time-domain spectroscopy of biomolecular crystals

    DEFF Research Database (Denmark)

    Kaltenecker, Korbinian J.; Engelbrecht, Sebastian; Iwaszczuk, Krzysztof

    2016-01-01

    Ultrabroadband THz time-domain spectroscopy based on two-color plasma generation and air biased coherent detection is used for the investigation of molecular dynamics of crystalline materials in the frequency range from 0.3 THz to 20 THz. We show that the spectral features in this extended freque...

  13. Free electron broad-band THz radiator

    CERN Document Server

    Doria, A; Giovenale, E

    2002-01-01

    In this paper, a comparison between the conventional Tera-Hertz (THz) sources and a THz radiator based on free electron devices is proposed. The basic idea of the exploitation of some of the features of the RF FELs will be presented together with some examples that could represent an appealing source to start with. A discussion about the link between the spectrum of the emitted radiation and the electron bunch length is presented. The necessity of generating very short bunch of electrons to be injected in the radiator is demonstrated.

  14. Towards Graphene GHz/THz Nanosensor

    Science.gov (United States)

    Mahjoub, Akram M.; Motooka, Shoutaro; Aoki, Nobuyuki; Song, Jungwoo; Bird, Jonathan P.; Kawano, Yukio; Ferry, David K.; Ishibashi, Koji; Ochiai, Yuichi

    2011-07-01

    A quantum dot (QD) sensing device, fabricated from nanoscaled carbon material has been studied using of a bilayer graphene field effect transistor in order to enable its application to the detection of microwave (GHz) and/or terahertz (THz) radiation. Recently, it has been found that there exist several common features in low temperature quantum transport, found in experimental results of conductance quantization in a semiconductor QDs and the magnetoresistance of a graphene QDs. The applicability of a graphene field effect transistor at the GHz/THz range is discussed in terms of the microwave transconductance characteristics up to 40 GHz.

  15. Characterization of European Lacquers by Terahertz (THz) Reflectometric Imaging

    DEFF Research Database (Denmark)

    Dandolo, Corinna Ludovica Koch; Jepsen, Peter Uhd; Christensen, Mads C.

    2013-01-01

    observe non-invasively buried layers of the lacquerware replica, including the internal structure of the wooden panel itself. We find that non-invasive terahertz reflectometric imaging analysis of lacquerware is can provide conservators with important information about the condition of the compositional...... layers, potentially aiding in the development of appropriate conservation treatments. With the same technique we have performed a surface material mapping. The material distribution has been enhanced through reflected THz composite RGB false color rendering, where RGB mapping allows distinction between...

  16. Electromagnetically Induced Transparency in Symmetric Planar Metamaterial at THz Wavelengths

    Directory of Open Access Journals (Sweden)

    Abdelwaheb Ourir

    2015-03-01

    Full Text Available We report the experimental observation and the evidence of the analogue of electromagnetically-induced transparency (EIT in a symmetric planar metamaterial. This effect has been obtained in the THz range thanks to a destructive Fano-interference between the two first modes of an array of multi-gap split ring resonators deposited on a silicon substrate. This structure is a planar thin film material with four-fold symmetry. Thanks to this property, a polarization-independent transmission has been achieved. The proposed metamaterial is well adapted to variety of slow-light applications in the infrared and optical range.

  17. Highly sensitive and selective sugar detection by terahertz nano-antennas

    Science.gov (United States)

    Lee, Dong-Kyu; Kang, Ji-Hun; Lee, Jun-Seok; Kim, Hyo-Seok; Kim, Chulki; Hun Kim, Jae; Lee, Taikjin; Son, Joo-Hiuk; Park, Q.-Han; Seo, Minah

    2015-10-01

    Molecular recognition and discrimination of carbohydrates are important because carbohydrates perform essential roles in most living organisms for energy metabolism and cell-to-cell communication. Nevertheless, it is difficult to identify or distinguish various carbohydrate molecules owing to the lack of a significant distinction in the physical or chemical characteristics. Although there has been considerable effort to develop a sensing platform for individual carbohydrates selectively using chemical receptors or an ensemble array, their detection and discrimination limits have been as high in the millimolar concentration range. Here we show a highly sensitive and selective detection method for the discrimination of carbohydrate molecules using nano-slot-antenna array-based sensing chips which operate in the terahertz (THz) frequency range (0.5-2.5 THz). This THz metamaterial sensing tool recognizes various types of carbohydrate molecules over a wide range of molecular concentrations. Strongly localized and enhanced terahertz transmission by nano-antennas can effectively increase the molecular absorption cross sections, thereby enabling the detection of these molecules even at low concentrations. We verified the performance of nano-antenna sensing chip by both THz spectra and images of transmittance. Screening and identification of various carbohydrates can be applied to test even real market beverages with a high sensitivity and selectivity.

  18. Novel Electrically Small Spherical Electric Dipole Antenna

    DEFF Research Database (Denmark)

    Kim, Oleksiy S.

    2010-01-01

    This paper introduces a novel electrically small spherical meander antenna. Horizontal sections of the meander are composed of wire loops, radii of which are chosen so that the whole structure is conformal to a sphere of radius a. To form the meander the loops are connected by wires at a meridian...... plane. The antenna operates as an electric dipole, i.e. it radiates the TM10 spherical mode. The antenna is self-resonant and can be matched to a wide range of input feed lines without an external matching network. In this paper, a spherical meander antenna of the size ka = 0.27 and the input impedance...

  19. Genetic programming techniques for thin-wire antennas

    Science.gov (United States)

    O'Donnell, Terry H.

    2007-04-01

    Simple genetic algorithm optimizations often utilize fixed-length chromosomes containing a predefined set of parameters to be optimized. While such algorithms have successfully created electrically small narrow-band and large wide-band military antennas, they require the antenna designer to have a fairly concrete antenna representation prior to exercising the genetic algorithm. In this research we investigate the use of genetic programming (GP) techniques to "program" the design of simple thin-wire antennas. Genetic programming techniques offer the potential to create random, multi-arm, multi-dimension antennas from variable length, tree-like chromosomes. We present a new genetic programming paradigm for creating multi-branched, thin-wire, genetic antennas and describe how GP commands are represented and decoded into physical antenna structures. We present preliminary results obtained from this algorithm showing evolutions along Pareto fronts representing antenna electrical size, VSWR, and antenna quality factor (Q).

  20. THz Imaging as a Method to Detect Defects of Aeronautical Coatings

    Science.gov (United States)

    Catapano, I.; Soldovieri, F.; Mazzola, L.; Toscano, C.

    2017-10-01

    Ice adhesion over critical aircraft surfaces is a serious potential hazard that runs the risk of causing accidents. To face this issue, the design and diagnostics of new multifunctional coatings with icephobic and aesthetical properties are demanded. In particular, diagnostic tools, capable of characterizing coating surface finishing and its defects, are needed. In this paper, terahertz (THz) imaging is considered as a high-resolution diagnostic tool useful for contactless surveys providing information on surface defects and material inner structure. Therefore, two composite specimens, one covered by a classical commercial livery coating and the other one by a new multifunctional coating with icephobic properties, are investigated by THz surveys carried out in normal environmental conditions of pressure and temperature. The results, obtained by processing the raw data properly, corroborate that THz imaging allows us to detect variations of the coating thickness, to localize hidden anomalies as well as to characterize surface defects at millimetric scale.

  1. Beam dynamics in THz dielectric-loaded waveguides for the AXSIS project

    Science.gov (United States)

    Vinatier, T.; Assmann, R. W.; Dorda, U.; Lemery, F.; Marchetti, B.

    2017-07-01

    In this paper, we investigate with ASTRA simulations the beam dynamics in dielectric-loaded waveguides driven by THz pulses, used as linac structure for the AXSIS project. We show that the bunch properties at the linac exit are very sensitive to the phase velocity of the THz pulse and are limited by the strong phase slippage of the bunch respective to it. We also show that the bunch properties are optimized when low frequencies (Work supported by the European Research Council under the European Union’s Seventh Framework Programme (FP/2007-2013)/ERC Grant Agreement n. 609920.

  2. Coaxial waveguide mode reconstruction and analysis with THz digital holography.

    Science.gov (United States)

    Wang, Xinke; Xiong, Wei; Sun, Wenfeng; Zhang, Yan

    2012-03-26

    Terahertz (THz) digital holography is employed to investigate the properties of waveguides. By using a THz digital holographic imaging system, the propagation modes of a metallic coaxial waveguide are measured and the mode patterns are restored with the inverse Fresnel diffraction algorithm. The experimental results show that the THz propagation mode inside the waveguide is a combination of four modes TE₁₁, TE₁₂, TM₁₁, and TM₁₂, which are in good agreement with the simulation results. In this work, THz digital holography presents its strong potential as a platform for waveguide mode charactering. The experimental findings provide a valuable reference for the design of THz waveguides.

  3. Design of a multistep phase mask for high-energy THz pulse generation in ZnTe crystal

    Science.gov (United States)

    Avetisyan, Yuri H.; Makaryan, Armen; Tadevosyan, Vahe

    2017-08-01

    A new scheme for generating high-energy terahertz (THz) pulses by optical rectification of tilted pulse front (TPF) femtosecond laser pulses in ZnTe crystal is proposed and analyzed. The TPF laser pulses are originated due to propagation through a multistep phase mask (MSPM) attached to the entrance surface of the nonlinear crystal. Similar to the case of contacting optical grating the necessity of the imaging optics is avoided. In addition, introduction of large amounts of angular dispersion is also eliminated. The operation principle is based on the fact that the MSPM splits a single input beam into many smaller time-delayed "beamlets", which together form a discretely TPF in the nonlinear crystal. The dimensions of the mask's steps required for high-energy THz-pulse generation in ZnTe and widely used lithium niobate (LN) crystals are calculated. The optimal number of steps is estimated taking into account individual beamlet's spatial broadening and problems related to the mask fabrication. The THz field in no pump depletion approximation is analytically calculated using radiating antenna model. The analysis shows that application of ZnTe crystal allows obtaining higher THz-pulse energy than that of LN crystal, especially when long-wavelength pump sources are used. The proposed method is a promising way to develop high-energy, monolithic, and alignment-free THzpulse source.

  4. Tunable structures and modulators for THz light

    Czech Academy of Sciences Publication Activity Database

    Kužel, Petr; Kadlec, Filip

    2008-01-01

    Roč. 9, - (2008), 197-214 ISSN 1631-0705 R&D Projects: GA AV ČR KJB100100512; GA MŠk LC512 Institutional research plan: CEZ:AV0Z10100520 Keywords : terahertz radiation * tunable devices * photonic crystals * strontium titanate * gallium arsenide Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.164, year: 2008

  5. Focal plane arrays for THz imaging

    NARCIS (Netherlands)

    Iacono, A.; Bencivenni, C.; Freni, A.; Neto, A.; Gerini, G.

    2012-01-01

    The growing attention for Terahertz technology finds support in the high number of applications which will benefit by its use. In the space science sector, the investigation of the THz frequency range will improve the knowledge of the universe, giving a clearer view on its origin and its evolution.

  6. European Research on THz Vacuum Amplifiers

    DEFF Research Database (Denmark)

    Brunetti, F.; Cojocarua, C.-S.; de Rossi, A.

    2010-01-01

    The OPTHER (OPtically Driven TeraHertz AmplifiERs) project represents a considerable advancement in the field of high frequency amplification. The design and realization of a THz amplifier within this project is a consolidation of efforts at the international level from the main players of the Eu...

  7. Microring Diode Laser for THz Generation

    DEFF Research Database (Denmark)

    Mariani, S.; Andronico, A.; Favero, I.

    2013-01-01

    We report on the modeling and optical characterization of AlGaAs/InAs quantum-dot microring diode lasers designed for terahertz (THz) difference frequency generation (DFG) between two whispering gallery modes (WGMs) around 1.3 $\\mu$m. In order to investigate the spectral features of this active...

  8. A multi-element THz imaging system

    DEFF Research Database (Denmark)

    Eichhorn, Finn; Høgstedt, Lasse; Buron, Jonas Christian Due

    2010-01-01

    We report on a broadband multi-element THz imaging system based on fiber-coupled, integrated photoconductive emitters and detectors. 32 detectors and 32 emitters are arranged in a planar array. Advanced image reconstruction algorithms are employed to reconstruct an object in the imaging plane....

  9. Generation of THz frequency using PANDA ring resonator for THz imaging

    Directory of Open Access Journals (Sweden)

    Ong CT

    2012-02-01

    Full Text Available MA Jalil1, Afroozeh Abdolkarim2, T Saktioto2, CT Ong3, Preecha P Yupapin41Ibnu Sina Institute of Fundamental Science Studies, Nanotechnology Research Alliance, Universiti Teknologi Malaysia (UTM,81310, Johor Bahru, Malaysia; 2Institute of Advanced Photonics Science, Nanotechnology Research Alliance, Universiti Teknologi Malaysia (UTM, 81310, Johor Bahru, Malaysia; 3Department of Mathematics, Universiti Teknologi Malaysia 81310 Skudai, Johor Bahru, Malaysia; 4Nanoscale Science and Engineering Research Alliance (N'SERA, Advanced Research Center for Photonics, Faculty of Science, King Mongkut's Institute of Technology Ladkrabang, Bangkok 10520, ThailandAbstract: In this study, we have generated terahertz (THz frequency by a novel design of microring resonators for medical applications. The dense wavelength-division multiplexing can be generated and obtained by using a Gaussian pulse propagating within a modified PANDA ring resonator and an add/drop filter system. Our results show that the THz frequency region can be obtained between 40–50 THz. This area of frequency provides a reliable frequency band for THz pulsed imaging.Keywords: THz imaging, THz technology, MRRs, PANDA, add/drop filter

  10. THz cavities and injectors for compact electron acceleration using laser-driven THz sources

    Directory of Open Access Journals (Sweden)

    Moein Fakhari

    2017-04-01

    Full Text Available We present a design methodology for developing ultrasmall electron injectors and accelerators based on cascaded cavities excited by short multicycle THz pulses obtained from laser-driven THz generation schemes. Based on the developed concept for optimal coupling of the THz pulse, a THz electron injector and two accelerating stages are designed. The designed electron gun consists of a four cell cavity operating at 300 GHz and a door-knob waveguide to coaxial coupler. Moreover, special designs are proposed to mitigate the problem of thermal heat flow and induced mechanical stress to achieve a stable device. We demonstrated a gun based on cascaded cavities that is powered by only 1.1 mJ of THz energy in 300 cycles to accelerate electron bunches up to 250 keV. An additional two linac sections can be added with five and four cell cavities both operating at 300 GHz boosting the bunch energy up to 1.2 MeV using a 4-mJ THz pulse.

  11. Design and Realization Aspects of 1-THz Cascade Backward Wave Amplifier Based on Double Corrugated Waveguide

    DEFF Research Database (Denmark)

    Paoloni, Claudio; Di Carlo, Aldo; Bouamrane, Fayçal

    2013-01-01

    The design and fabrication challenges in the first ever attempt to realize a 1-THz vacuum tube amplifier are described. Implementation of innovative solutions including a slow-wave structure in the form of a double corrugated waveguide, lateral tapered input and output couplers, deep X-ray LIGA...

  12. Extremely High-Birefringent Asymmetric Slotted-Core Photonic Crystal Fiber in THz Regime

    DEFF Research Database (Denmark)

    Islam, Raonaqul; Habib, Selim; Hasanuzzaman, G.K.M.

    2015-01-01

    of the circular cladding confines most of the power in the fiber-core. The fiber structure reported in this letter exhibits simultaneously ultrahigh modal birefringence of 7.5 × 10−2 and a very low effective absorption loss of 0.07 cm−1 for y-polarization mode at an operating frequency of 1 THz. It is highly...

  13. Terahertz (THz) Optical Parameters of Three-Dimensional (3-D) Printing Materials

    Science.gov (United States)

    2017-03-01

    additively created structures versus those created using standard processes , such as injection molding , casting, or machining. Terahertz (THz) radiation...nonconductive extrusion industry. Quantifying parts manufactured using additive processes is an unknown, as is understanding the material properties of...OTHER AUTHORIZED DOCUMENTS. TRADE NAMES USE OF TRADE NAMES OR MANUFACTURERS IN THIS REPORT DOES NOT CONSTITUTE AN OFFICIAL ENDORSEMENT OR

  14. Independent Peer Review of Communications, Navigation, and Networking re-Configurable Testbed (CoNNeCT) Project Antenna Pointing Subsystem (APS) Integrated Gimbal Assembly (IGA) Structural Analysis

    Science.gov (United States)

    Raju, Ivatury S.; Larsen, Curtis E.; Pellicciotti, Joseph W.

    2010-01-01

    Glenn Research Center Chief Engineer's Office requested an independent review of the structural analysis and modeling of the Communications, Navigation, and Networking re-Configurable Testbed (CoNNeCT) Project Antenna Pointing Subsystem (APS) Integrated Gimbal Assembly (IGA) to be conducted by the NASA Engineering and Safety Center (NESC). At this time, the IGA had completed its critical design review (CDR). The assessment was to be a peer review of the NEi-NASTRAN1 model of the APS Antenna, and not a peer review of the design and the analysis that had been completed by the GRC team for CDR. Thus, only a limited amount of information was provided on the structural analysis. However, the NESC team had difficulty separating analysis concerns from modeling issues. The team studied the NASTRAN model, but did not fully investigate how the model was used by the CoNNeCT Project and how the Project was interpreting the results. The team's findings, observations, and NESC recommendations are contained in this report.

  15. Far field focusing for a microwave patch antenna with composite substrate

    Directory of Open Access Journals (Sweden)

    Jian Wan

    2018-03-01

    Full Text Available Modeling for a compact microwave antenna structure on base of a miniaturized rectangular patch antenna with composite substrate and magnetic superstrates is made in this study by using FDTD simulations. The resonant frequency of the antenna structure is supposed to be 15 GHz. The design of the antenna with composite substrate and without superstrate is made up by using the microwave miniaturization concept for rectangular patch antennas created by first author of this study. The optimal distance between the superstrate and antenna surface is found by using Fabry-Perot cavity theory as maximum values of power directivity and efficiency of the antenna is achieved. The comparative analysis with regard to some far and near field parameters of the above antenna structures and the antenna with dielectric substrate having same value of the relative permittivity is performed. Keywords: Patch antennas, Metamaterials, Effective parameters, Antenna substrate technology

  16. Porous textile antenna designs for improved wearability

    Science.gov (United States)

    Shahariar, Hasan; Soewardiman, Henry; Muchler, Clifford A.; Adams, Jacob J.; Jur, Jesse S.

    2018-04-01

    Textile antennas are an integral part of the next generation personalized wearable electronics system. However, the durability of textile antennas are rarely discussed in the literature. Typical textile antennas are prone to damage during normal wearable user scenarios, washing, and heat cycling over time. Fabricating a durable, washable, flexible, and breathable (like textile materials) antenna is challenging due to the incompatibility of the mechanical properties of conductive materials and soft textile materials. This paper describes a scalable screen printing process on an engineered nonwoven substrate to fabricate microstrip patch antennas with enhanced durability. This work used an Evolon® nonwoven substrate with low surface roughness (˜Ra = 18 μm) and high surface area (˜2.05 mm2 mm-2 of fabric area) compared to traditional textile materials, which allows the ink to penetrate evenly in the fiber bulk with its strong capillary wicking force and enhances print resolution. The composite layer of ink and fiber is conductive and enables the antennas to maintain high mechanical flexibility without varying its RF (Radio Frequency) properties. Additionally, the antennas are packaged by laminating porous polyurethane web to make the device durable and washable. The fully packaged antennas maintain the structural flexibility and RF functionality after 15 cycles of washing and drying. To improve the air permeability and enhance flexibility the antenna is also modified by incorporating holes in the both patch and ground layer of the antenna. The antennas were analyzed before and after submerging in water to observe the effect of wetting and drying with respect to frequency response. The porous antenna with holes recovered 3x times faster than the one without holes (solid) from fully wet state (saturated with water) to the dry state, demonstrating its potential use as a moisture sensor system.

  17. Design of wire antennas with using of genetic algorithms

    OpenAIRE

    Chavka, G. G.; Litwinczuk, N.

    2007-01-01

    Methods of computer-aided design and an optimization of antennas with a using of genetic algorithms are represented in the paper. A general basis of the design and the optimization of antennas are discussed. Main ideas, parameters, structure and network properties of the genetic algorithms are described. Results of the design antennas are presented.

  18. Performance assessment of a data processing chain for THz imaging

    Science.gov (United States)

    Catapano, Ilaria; Ludeno, Giovanni; Soldovieri, Francesco

    2017-04-01

    Nowadays, TeraHertz (THz) imaging is deserving huge attention as very high resolution diagnostic tool in many applicative fields, among which security, cultural heritage, material characterization and civil engineering diagnostics. This widespread use of THz waves is due to their non-ionizing nature, their capability of penetrating into non-metallic opaque materials, as well as to the technological advances, which have allowed the commercialization of compact, flexible and portable systems. However, the effectiveness of THz imaging depends strongly on the adopted data processing aimed at improving the imaging performance of the hardware device. In particular, data processing is required to mitigate detrimental and unavoidable effects like noise, signal attenuation, as well as to correct the sample surface topography. With respect to data processing, we have proposed recently a strategy involving three different steps aimed at reducing noise, filtering out undesired signal introduced by the adopted THz system and performing surface topography correction [1]. The first step regards noise filtering and exploits a procedure based on the Singular Value Decomposition (SVD) [2] of the data matrix, which does not require knowledge of noise level and it does not involve the use of a reference signal. The second step aims at removing the undesired signal that we have experienced to be introduced by the adopted Z-Omega Fiber-Coupled Terahertz Time Domain (FICO) system. Indeed, when the system works in a high-speed mode, an undesired low amplitude peak occurs always at the same time instant from the beginning of the observation time window and needs to be removed from the useful data matrix in order to avoid a wrong interpretation of the imaging results. The third step of the considered data processing chain is a topographic correction, which needs in order to image properly the samples surface and its inner structure. Such a procedure performs an automatic alignment of the

  19. Change of diamond film structure and morphology with N2 addition in MW PECVD apparatus with linear antenna delivery system

    Czech Academy of Sciences Publication Activity Database

    Jakl Krečmarová, Marie; Petrák, Václav; Taylor, Andrew; Sankaran, K. J.; Lin, I. N.; Jäger, Aleš; Gärtnerová, Viera; Fekete, Ladislav; Drahokoupil, Jan; Laufek, František; Vacík, Jiří; Hubík, Pavel; Mortet, Vincent; Nesladek, M.

    2014-01-01

    Roč. 211, č. 10 (2014), s. 2296-2301 ISSN 1862-6300 R&D Projects: GA ČR GA13-31783S; GA MŠk(CZ) LM2011026; GA MŠk(XE) LM2011019 Grant - others:OP VK(XE) CZ.1.07/2.3.00/20.0306; AV ČR(CZ) Fellowship J. E. Purkyně Institutional support: RVO:68378271 ; RVO:61389005 Keywords : linear antenna * nano- diamond * nitrogen doping * TEM * Raman spectroscopy Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.616, year: 2014 http://onlinelibrary.wiley.com/doi/10.1002/pssa.201431255/full

  20. Radiation and scattering by thin-wire structures in the complex frequency domain. [electromagnetic theory for thin-wire antennas

    Science.gov (United States)

    Richmond, J. H.

    1974-01-01

    Piecewise-sinusoidal expansion functions and Galerkin's method are employed to formulate a solution for an arbitrary thin-wire configuration in a homogeneous conducting medium. The analysis is performed in the real or complex frequency domain. In antenna problems, the solution determines the current distribution, impedance, radiation efficiency, gain and far-field patterns. In scattering problems, the solution determines the absorption cross section, scattering cross section and the polarization scattering matrix. The electromagnetic theory is presented for thin wires and the forward-scattering theorem is developed for an arbitrary target in a homogeneous conducting medium.

  1. Millimeter-Waves Structures on Benzocyclobutene Dielectric Substrate

    Directory of Open Access Journals (Sweden)

    G. Di Massa

    2011-12-01

    Full Text Available The need of low-loss substrate materials with stable dielectric performances is a strong requirement when working at millimeter frequencies, where standard dielectrics exhibit prohibitive losses. In this paper, the authors focus their attention on a polymer material, the benzocyclobutene (BCB, having a low dielectric constant and a low loss tangent, with a stable behavior up to THz frequencies. A specific in-house manufacture technology is described to realize millimeter-wave structures on a BCB dielectric substrate. Experimental validations on BCB-based circuits and antennas prototypes are discussed.

  2. 6.1 Research Areas in the Antenna Group

    Science.gov (United States)

    2014-07-01

    and support structures using three-dimensional (3-D) printers is an essential part of novel antenna developments. 2.2 Carbon Nanotubes (CNT) for... textile -integrated, and multifunctional antennas realized from emerging nanomaterials (e.g., carbon nanotubes [CNT] and graphene). The application of...platforms and high durability antennas for conformal, textile - integrated, and/or vehicle-integrated antenna applications. Frequencies of interest range

  3. Antenna Pattern Range (APR)

    Data.gov (United States)

    Federal Laboratory Consortium — TheAntenna Pattern Range (APR)features a non-metallic arch with a trolley to move the transmit antenna from the horizon to zenith. At the center of the ground plane,...

  4. A Single Atom Antenna

    International Nuclear Information System (INIS)

    Trinter, Florian; Williams, Joshua B; Weller, Miriam; Waitz, Markus; Pitzer, Martin; Voigtsberger, Jörg; Schober, Carl; Kastirke, Gregor; Müller, Christian; Goihl, Christoph; Burzynski, Phillip; Wiegandt, Florian; Wallauer, Robert; Kalinin, Anton; Schmidt, Lothar Ph H; Schöffler, Markus S; Jahnke, Till; Dörner, Reinhard; Chiang, Ying-Chih; Gokhberg, Kirill

    2015-01-01

    Here we demonstrate the smallest possible implementation of an antenna-receiver complex which consists of a single (helium) atom acting as the antenna and a second (neon) atom acting as a receiver. (paper)

  5. Compact Low Frequency Radio Antenna

    Science.gov (United States)

    Punnoose, Ratish J.

    2008-11-11

    An antenna is disclosed that comprises a pair of conductive, orthogonal arches and a pair of conductive annular sector plates, wherein adjacent legs of each arch are fastened to one of the annular sector plates and the opposite adjacent pair of legs is fastened to the remaining annular sector plate. The entire antenna structure is spaced apart from a conductive ground plane by a thin dielectric medium. The antenna is driven by a feed conduit passing through the conductive ground plane and dielectric medium and attached to one of the annular sector plates, wherein the two orthogonal arched act as a pair of crossed dipole elements. This arrangement of elements provides a radiation pattern that is largely omni-directional above the horizon.

  6. High-Q Antennas with built-in coils

    DEFF Research Database (Denmark)

    Bahramzy, Pevand; Svendsen, Simon; Pedersen, Gert Frølund

    2014-01-01

    Efficiency and isolation, at low frequencies (700 MHz), are two of the most important metrics for successful multicommunication implementation. This paper presents an antenna concept, that exhibits a very high isolation between high-Q Tx and Rx antennas at 700 MHz. Furthermore, it is shown how co...... coils can be integrating into the antenna structure for obtaining better efficiency. It is shown that by integrated coils into the antenna structure, the efficiency can be improved by 2dB for each antenna....

  7. Photonic generation for multichannel THz wireless communication.

    Science.gov (United States)

    Shams, Haymen; Fice, Martyn J; Balakier, Katarzyna; Renaud, Cyril C; van Dijk, Frédéric; Seeds, Alwyn J

    2014-09-22

    We experimentally demonstrate photonic generation of a multichannel THz wireless signal at carrier frequency 200 GHz, with data rate up to 75 Gbps in QPSK modulation format, using an optical heterodyne technique and digital coherent detection. BER measurements were carried out for three subcarriers each modulated with 5 Gbaud QPSK or for two subcarriers modulated with 10 Gbaud QPSK, giving a total speed of 30 Gbps or 40 Gbps, respectively. The system evaluation was also performed with three subcarriers modulated with 12.5 Gbaud QPSK (75 Gbps total) without and with 40 km fibre transmission. The proposed system enhances the capacity of high-speed THz wireless transmission by using spectrally efficient modulated subcarriers spaced at the baud rate. This approach increases the overall transmission capacity and reduces the bandwidth requirement for electronic devices.

  8. Active metamaterial: Gain and stability, and microfluidic chip for THz cell spectroscopy

    Science.gov (United States)

    Tang, Qi

    Metamaterials are artificially designed composite materials which can exhibit unique and unusual properties such as the negative refractive index, negative phase velocity, etc. The concept of metamaterials becomes prevalent in the electromagnetic society since the first experimental implementation in the early 2000s. Many fascinated potential applications, e.g. super lens, invisibility cloaking, and novel antennas that are electrically small, have been proposed based on metamaterials. However, most of the applications still remain in theory and are not suitable for practical applications mainly due to the intrinsic loss and narrow bandwidth (large dispersion) determined by the fundamental physics of metamaterials. In this dissertation, we incorporate active gain devices into conventional passive metamaterials to overcome loss and even provide gain. Two types of active gain negative refractive index metamaterials are proposed, designed and experimentally demonstrated, including an active composite left-/right-handed transmission line and an active volumetric metamaterial. In addition, we investigate the non-Foster circuits for broadband matching of electrically small antennas. A rigorous way of analyzing the stability of non-Foster circuits by normalized determinant function is proposed. We study the practical factors that may affect the stability of non-Foster circuits, including the device parasitics, DC biasing, layouts and load impedance. A stable floating negative capacitor is designed, fabricated and tested. Moreover, it is important to resolve the sign of refractive index for active gain media which can be quite challenging. We investigate the analytical solution of a gain slab system, and apply the Nyquist criterion to analyze the stability of a causal gain medium. We then emphasize that the result of frequency domain simulation has to be treated with care. Lastly, this dissertation discusses another interesting topic about THz spectroscopy of live cells

  9. A microfabricated low-profile wideband antenna array for terahertz communications.

    Science.gov (United States)

    Luk, K M; Zhou, S F; Li, Y J; Wu, F; Ng, K B; Chan, C H; Pang, S W

    2017-04-28

    While terahertz communications are considered to be the future solutions for the increasing demands on bandwidth, terahertz equivalents of radio frequency front-end components have not been realized. It remains challenging to achieve wideband, low profile antenna arrays with highly directive beams of radiation. Here, based on the complementary antenna approach, a wideband 2 × 2 cavity-backed slot antenna array with a corrugated surface is proposed. The approach is based on a unidirectional antenna with a cardiac radiation pattern and stable frequency characteristics that is achieved by integrating a series-resonant electric dipole with a parallel-resonant magnetic dipole. In this design, the slots work as magnetic dipoles while the corrugated surface radiates as an array of electric dipoles. The proposed antenna is realized at 1 THz operating frequency by stacking multiple metallized layers using the microfabrication technology. S-parameter measurements of this terahertz low-profile metallic antenna array demonstrate high efficiency at terahertz frequencies. Fractional bandwidth and gain are measured to be 26% and 14 dBi which are consistent with the simulated results. The proposed antenna can be used as the building block for larger antenna arrays with more directive beams, paving the way to develop high gain low-profile antennas for future communication needs.

  10. Evolutionary Optimization of a Quadrifilar Helical Antenna

    Science.gov (United States)

    Lohn, Jason D.; Kraus, William F.; Linden, Derek S.; Clancy, Daniel (Technical Monitor)

    2002-01-01

    Automated antenna synthesis via evolutionary design has recently garnered much attention in the research literature. Evolutionary algorithms show promise because, among search algorithms, they are able to effectively search large, unknown design spaces. NASA's Mars Odyssey spacecraft is due to reach final Martian orbit insertion in January, 2002. Onboard the spacecraft is a quadrifilar helical antenna that provides telecommunications in the UHF band with landed assets, such as robotic rovers. Each helix is driven by the same signal which is phase-delayed in 90 deg increments. A small ground plane is provided at the base. It is designed to operate in the frequency band of 400-438 MHz. Based on encouraging previous results in automated antenna design using evolutionary search, we wanted to see whether such techniques could improve upon Mars Odyssey antenna design. Specifically, a co-evolutionary genetic algorithm is applied to optimize the gain and size of the quadrifilar helical antenna. The optimization was performed in-situ in the presence of a neighboring spacecraft structure. On the spacecraft, a large aluminum fuel tank is adjacent to the antenna. Since this fuel tank can dramatically affect the antenna's performance, we leave it to the evolutionary process to see if it can exploit the fuel tank's properties advantageously. Optimizing in the presence of surrounding structures would be quite difficult for human antenna designers, and thus the actual antenna was designed for free space (with a small ground plane). In fact, when flying on the spacecraft, surrounding structures that are moveable (e.g., solar panels) may be moved during the mission in order to improve the antenna's performance.

  11. Super wideband characteristics of monopolar patch antenna

    Directory of Open Access Journals (Sweden)

    Xi Chen

    2013-12-01

    Full Text Available A simple method of acquiring super wideband characteristics for monopolar patch antenna is proposed. Through adopting a modified cone as feeding and radiating structure, the monopolar patch antenna can reach the impedance bandwidth of more than 1:23.4 for voltage standing wave ratio (VSWR ≤ 2. In the whole operating band, the antenna has the like-monopole omnidirectional radiation patterns and the peak gains of 3.8–8.7 dB. Meanwhile, the height of the antenna is just 0.074λ(c, and the diameter of the radiated body is 0.205λ(c, which is smaller than other ultra-wideband omnidirectional antenna.

  12. Broadband microstrip patch antennas

    International Nuclear Information System (INIS)

    El Sharkawy, Z.F.M

    2010-01-01

    Personal communication systems such as cellular telephones, global positioning systems, indoor and outdoor wireless communication are become very popular . Highly efficient, low profile antenna with large impedance bandwidth capabilities is desired. Microstrip patch antennas are applicable in these systems. Using three methods to analyze the MPA, analytical models i.e (transmission line model TLM, and cavity model CM), finite element method via HFSS, and finite integration technique via CST MWS. investigate and classify the techniques that used to improve the operating impedance bandwidth for MPA, so as to use them in our new MPA structures. New MPA configurations are introduced. In the first application, two symmetrical rectangular ring slots are introduced on the patch. An impedance bandwidth of about 48.1% is experimentally obtained. Further modifications (i.e., probe position,and substrate thickness) have been made to obtain a wider impedance bandwidth. An impedance bandwidth of about 48.7% has been obtained.In the second structure, two identical slits have been cut out from the patch.This makes the patch seems like 2-shape.An impedance bandwidth about 49.24% is obtained.In third structure, two techniques are used for MPA.The first: is segmenting the fed parch, the second : another square patch is stacked over the fed one.This arrangement increases the impedance bandwidth up to 2.04:1. In the fourth structure,two techniques are introduced. The first: F-probe technique.The second : diamond patch with parasitic elements.This arrangement increases the impedance bandwidth up to 78.1%.In the fifth structure, three techniques are introduced.The first : two slots have been cut out from the patch, and two levels have been etched from its edges.The second : Two symmetrical parasitic rectangle patches are introduced. The third : partial ground plane is used.

  13. 47 CFR 95.408 - (CB Rule 8) How high may I put my antenna?

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false (CB Rule 8) How high may I put my antenna? 95....408 (CB Rule 8) How high may I put my antenna? (a) Antenna means the radiating system (for... everything else attached to the radiating system and the structure. (b) If your antenna is mounted on a hand...

  14. Generation and detection of ultrabroadband infrared wave exceeding 200 THz

    Directory of Open Access Journals (Sweden)

    Ashida Masaaki

    2013-03-01

    Full Text Available By focusing a hollow-fiber compressed intense 10–fs pulse and its second harmonic in air, an ultrabroadband infrared pulse with a spectral range of 1–200 THz is generated through a plasma. Coherent detection of the signal up to 100 THz is achieved with electro–optic sampling and THz air-breakdown-coherent-detection. The drastic dependence on the orientation of the second harmonic crystal is clarified in a range of 100–200 THz. From these, the whole frequency components are confirmed to be generated from the AC biased plasma and phase-locked.

  15. Antenna Controller Replacement Software

    Science.gov (United States)

    Chao, Roger Y.; Morgan, Scott C.; Strain, Martha M.; Rockwell, Stephen T.; Shimizu, Kenneth J.; Tehrani, Barzia J.; Kwok, Jaclyn H.; Tuazon-Wong, Michelle; Valtier, Henry; Nalbandi, Reza; hide

    2010-01-01

    The Antenna Controller Replacement (ACR) software accurately points and monitors the Deep Space Network (DSN) 70-m and 34-m high-efficiency (HEF) ground-based antennas that are used to track primarily spacecraft and, periodically, celestial targets. To track a spacecraft, or other targets, the antenna must be accurately pointed at the spacecraft, which can be very far away with very weak signals. ACR s conical scanning capability collects the signal in a circular pattern around the target, calculates the location of the strongest signal, and adjusts the antenna pointing to point directly at the spacecraft. A real-time, closed-loop servo control algorithm performed every 0.02 second allows accurate positioning of the antenna in order to track these distant spacecraft. Additionally, this advanced servo control algorithm provides better antenna pointing performance in windy conditions. The ACR software provides high-level commands that provide a very easy user interface for the DSN operator. The operator only needs to enter two commands to start the antenna and subreflector, and Master Equatorial tracking. The most accurate antenna pointing is accomplished by aligning the antenna to the Master Equatorial, which because of its small size and sheltered location, has the most stable pointing. The antenna has hundreds of digital and analog monitor points. The ACR software provides compact displays to summarize the status of the antenna, subreflector, and the Master Equatorial. The ACR software has two major functions. First, it performs all of the steps required to accurately point the antenna (and subreflector and Master Equatorial) at the spacecraft (or celestial target). This involves controlling the antenna/ subreflector/Master-Equatorial hardware, initiating and monitoring the correct sequence of operations, calculating the position of the spacecraft relative to the antenna, executing the real-time servo control algorithm to maintain the correct position, and

  16. Feasibility Study of a Laser Beat-Wave Seeded THz FEL at the Neptune Laboratory

    CERN Document Server

    Reiche, Sven; Pellegrini, Claudio; Rosenzweig, James E; Shvets, Gennady; Tochitsky, Sergei Ya

    2005-01-01

    Free-Electron Laser in the THz range can be used to generate high output power radiation or to modulate the electron beam longitudinally on the radiation wavelength scale. Microbunching on the scale of 1-5 THz is of particular importance for potential phase-locking of a modulated electron beam to a laser-driven plasma accelerating structure. However the lack of a seeding source for the FEL at this spectral range limits operation to a SASE FEL only, which denies a subpicosecond synchronization of the current modulation or radiation with an external laser source. One possibility to overcome this problem is to seed the FEL with two external laser beams, which difference (beat-wave) frequency is matched to the resonant FEL frequency in the THz range. In this presentation we study feasibility of an experiment on laser beat-wave injection in the THz FEL considered at the UCLA Neptune Laboratory, where both a high brightness photoinjector and a two-wavelength, TW-class CO2 laser system exist. By incorporating the en...

  17. Ultrafast nonlinear carrier dynamics in doped semiconductors in high THz fields

    DEFF Research Database (Denmark)

    Hoffmann, Matthias C.; Turchinovich, Dmitry

    2011-01-01

    THz frequency saturable absorption and intervalley carrier scattering in n-type semiconductors were observed using intensity-dependent transmission experiments as well as THz-pump—THz probe spectroscopy with ultrabroadband probe pulses.......THz frequency saturable absorption and intervalley carrier scattering in n-type semiconductors were observed using intensity-dependent transmission experiments as well as THz-pump—THz probe spectroscopy with ultrabroadband probe pulses....

  18. Compact concentric ring shaped antenna for ultra wide band applications

    Science.gov (United States)

    Singha, Rahul; Vakula, D.; Sarma, N. V. S. N.

    2014-10-01

    A novel antenna for compact size, simple structure suitable for low cost fabrication is proposed for UWB application. A compact ring shaped monopole antenna is designed to cover the entire ultra wide bandwidth which has straight forward printed circuit board integration. The dimensions of the antenna are 16mm × 12mm × 0.787mm. More specifically, the impedance matching of the antenna is improved by employment of the tapered microstrip feed line. The measurement and simulation results show that the proposed antenna achieves good impedance bandwidth from 6.5 GHz to 25 GHz which covers the entire UWB. The antenna also has a gain approximately 2.5dBi from 6 GHz to 22 GHz. Compared to the existing UWB antennas, the presented modified structure has the smallest size, the widest bandwidth and better return loss characteristics.

  19. Coherent detection of THz waves based on THz-induced time-resolved luminescence quenching in bulk gallium arsenide.

    Science.gov (United States)

    Chu, Zheng; Liu, Jinsong; Wang, Kejia

    2012-05-01

    A kind of photoluminescence quenching, in which the time-resolved photoluminescence is modulated by a THz pulse, has been theoretically investigated by performing the ensemble Monte Carlo method in bulk gallium arsenide (GaAs) at room temperature. The quenching ratio could reach up to 50% under a strong THz field (100  kV/cm). The range in which luminescence quenching is linearly proportional to the THz field could be over 60  kV/cm. On the basis of these results, a principle for THz modulation and coherent detection is proposed.

  20. The Physics and Mathematical Theory of Nano-Scaled Ring Resonators and Loop Antennas

    OpenAIRE

    McKinley, A. F.

    2014-01-01

    This thesis is based on the realisation that no analytical theory of loop antennas and rings exists that is at once applicable to the Radio Frequency (RF), Micro-wave (MW), TeraHertz (THz), Infra-red (IR), and Optical (OR) regions. Nor is there any Electrical Engineering circuit model, rigorously developed from the results of that theory, that generates results which match numerical simulations and experimental work in the literature across all of these regimes. This thesis fills that gap. Ma...

  1. Frequency selective surfaces based high performance microstrip antenna

    CERN Document Server

    Narayan, Shiv; Jha, Rakesh Mohan

    2016-01-01

    This book focuses on performance enhancement of printed antennas using frequency selective surfaces (FSS) technology. The growing demand of stealth technology in strategic areas requires high-performance low-RCS (radar cross section) antennas. Such requirements may be accomplished by incorporating FSS into the antenna structure either in its ground plane or as the superstrate, due to the filter characteristics of FSS structure. In view of this, a novel approach based on FSS technology is presented in this book to enhance the performance of printed antennas including out-of-band structural RCS reduction. In this endeavor, the EM design of microstrip patch antennas (MPA) loaded with FSS-based (i) high impedance surface (HIS) ground plane, and (ii) the superstrates are discussed in detail. The EM analysis of proposed FSS-based antenna structures have been carried out using transmission line analogy, in combination with the reciprocity theorem. Further, various types of novel FSS structures are considered in desi...

  2. Spectral Trends of Solar Bursts at Sub-THz Frequencies

    Science.gov (United States)

    Fernandes, L. O. T.; Kaufmann, P.; Correia, E.; Giménez de Castro, C. G.; Kudaka, A. S.; Marun, A.; Pereyra, P.; Raulin, J.-P.; Valio, A. B. M.

    2017-01-01

    Previous sub-THz studies were derived from single-event observations. We here analyze for the first time spectral trends for a larger collection of sub-THz bursts. The collection consists of a set of 16 moderate to small impulsive solar radio bursts observed at 0.2 and 0.4 THz by the Solar Submillimeter-wave Telescope (SST) in 2012 - 2014 at El Leoncito, in the Argentinean Andes. The peak burst spectra included data from new solar patrol radio telescopes (45 and 90 GHz), and were completed with microwave data obtained by the Radio Solar Telescope Network, when available. We critically evaluate errors and uncertainties in sub-THz flux estimates caused by calibration techniques and the corrections for atmospheric transmission, and introduce a new method to obtain a uniform flux scale criterion for all events. The sub-THz bursts were searched during reported GOES soft X-ray events of class C or larger, for periods common to SST observations. Seven out of 16 events exhibit spectral maxima in the range 5 - 40 GHz with fluxes decaying at sub-THz frequencies (three of them associated to GOES class X, and four to class M). Nine out of 16 events exhibited the sub-THz spectral component. In five of these events, the sub-THz emission fluxes increased with a separate frequency from that of the microwave spectral component (two classified as X and three as M), and four events have only been detected at sub-THz frequencies (three classified as M and one as C). The results suggest that the THz component might be present throughout, with the minimum turnover frequency increasing as a function of the energy of the emitting electrons. The peculiar nature of many sub-THz burst events requires further investigations of bursts that are examined from SST observations alone to better understand these phenomena.

  3. The Influence of the Annealing Regime on the Properties of Terahertz Antennas Based on Low-Temperature-Grown Gallium Arsenide

    Science.gov (United States)

    Nomoev, S. A.; Vasil'evskii, I. S.; Vinichenko, A. N.; Kozlovskii, K. I.; Chistyakov, A. A.; Mishina, E. D.; Khusyainov, D. I.; Buryakov, A. M.

    2018-01-01

    Low-temperature gallium arsenide (LT-GaAs) films were grown by the method of molecularbeam epitaxy (MBE) at a reduced temperature (230°C) on GaAs(100) substrates and subjected to postgrowth annealing in various regimes. Photoconductive antennas (PCAs) with flag geometry formed on the film surface were characterized by terahertz (THz) response power at various bias voltages. The method of THz spectroscopy was used to study the characteristics of PCAs based on LT-GaAs films annealed in various regimes and the optimum interval of postgrowth annealing temperatures (670-720°C) was established.

  4. Spoof surface plasmon based planar antennas for the realization of Terahertz hotspots

    Science.gov (United States)

    Zhang, Yusheng; Han, Zhanghua

    2015-01-01

    Novel spoof surface plasmon based terahertz (THz) antennas are realized using a few number of rectangular grooves perforated in ultrathin metal stripes and the properties of them, including both scattering cross sections and field enhancement, are numerically analyzed. The dependence of these properties on the incident angle and groove number is discussed and the results show that sharp resonances in scattering cross section spectra associated with strong local field enhancement can be achieved. These resonances are due to the formation of Fabry-Perot resonances of the spoof surface plasmon mode and it is found that the order of resonance exhibiting strongest field enhancements is found to coincide with the number of grooves at normal incidence, due to hybridization of the antenna resonance with the individual groove resonance. The terahertz hotspots within the grooves at resonances due to the local field enhancement may open up new possibilities for the investigation of terahertz-matter interactions and boost a variety of THz applications including novel sensing and THz detections. The planar stripe antennas with sharper resonances than dipolar-like resonances, together with their ease of fabrication may also promise new design methodology for metamaterials. PMID:26691003

  5. Advanced Communication Technology Satellite (ACTS) multibeam antenna analysis and experiment

    Science.gov (United States)

    Acosta, Roberto J.; Lagin, Alan R.; Larko, Jeffrey M.; Narvaez, Adabelle

    1992-01-01

    One of the most important aspects of a satellite communication system design is the accurate estimation of antenna performance degradation. Pointing error, end coverage gain, peak gain degradation, etc. are the main concerns. The thermal or dynamic distortions of a reflector antenna structural system can affect the far-field antenna power distribution in a least four ways. (1) The antenna gain is reduced; (2) the main lobe of the antenna can be mispointed thus shifting the destination of the delivered power away from the desired locations; (3) the main lobe of the antenna pattern can be broadened, thus spreading the RF power over a larger area than desired; and (4) the antenna pattern sidelobes can increase, thus increasing the chances of interference among adjacent beams of multiple beam antenna system or with antenna beams of other satellites. The in-house developed NASA Lewis Research Center thermal/structural/RF analysis program was designed to accurately simulate the ACTS in-orbit thermal environment and predict the RF antenna performance. The program combines well establish computer programs (TRASYS, SINDA and NASTAN) with a dual reflector-physical optics RF analysis program. The ACTS multibeam antenna configuration is analyzed and several thermal cases are presented and compared with measurements (pre-flight).

  6. FDTD simulation tools for UWB antenna analysis.

    Energy Technology Data Exchange (ETDEWEB)

    Brocato, Robert Wesley

    2004-12-01

    This paper describes the development of a set of software tools useful for analyzing ultra-wideband (UWB) antennas and structures. These tools are used to perform finite difference time domain (FDTD) simulation of a conical antenna with continuous wave (CW) and UWB pulsed excitations. The antenna is analyzed using spherical coordinate-based FDTD equations that are derived from first principles. The simulation results for CW excitation are compared to simulation and measured results from published sources; the results for UWB excitation are new.

  7. FDTD simulation tools for UWB antenna analysis.

    Energy Technology Data Exchange (ETDEWEB)

    Brocato, Robert Wesley

    2005-02-01

    This paper describes the development of a set of software tools useful for analyzing ultra-wideband (UWB) antennas and structures. These tools are used to perform finite difference time domain (FDTD) simulation of a conical antenna with continuous wave (CW) and UWB pulsed excitations. The antenna is analyzed using spherical coordinate-based FDTD equations that are derived from first principles. The simulation results for CW excitation are compared to simulation and measured results from published sources; the results for UWB excitation are new.

  8. Mapping an on-chip terahertz antenna by a scanning near-field probe and a fixed field-effect transistor

    International Nuclear Information System (INIS)

    Lü Li; Sun Jian-Dong; Wu Dong-Min; Cai Yong; Qin Hua; Lewis, Roger A.; Sun Yun-Fei

    2015-01-01

    In the terahertz (THz) regime, the active region for a solid-state detector usually needs to be implemented accurately in the near-field region of an on-chip antenna. Mapping of the near-field strength could allow for rapid verification and optimization of new antenna/detector designs. Here, we report a proof-of-concept experiment in which the field mapping is realized by a scanning metallic probe and a fixed AlGaN/GaN field-effect transistor. Experiment results agree well with the electromagnetic-wave simulations. The results also suggest a field-effect THz detector combined with a probe tip could serve as a high sensitivity THz near-field sensor. (paper)

  9. Nanoscale electron manipulation in metals with intense THz electric fields

    Science.gov (United States)

    Takeda, Jun; Yoshioka, Katsumasa; Minami, Yasuo; Katayama, Ikufumi

    2018-03-01

    Improved control over the electromagnetic properties of metals on a nanoscale is crucial for the development of next-generation nanoelectronics and plasmonic devices. Harnessing the terahertz (THz)-electric-field-induced nonlinearity for the motion of electrons is a promising method of manipulating the local electromagnetic properties of metals, while avoiding undesirable thermal effects and electronic transitions. In this review, we demonstrate the manipulation of electron delocalization in ultrathin gold (Au) films with nanostructures, by intense THz electric-field transients. On increasing the electric-field strength of the THz pulses, the transmittance in the THz-frequency region abruptly decreases around the percolation threshold. The observed THz-electric-field-induced nonlinearity is analysed, based on the Drude-Smith model. The results suggest that ultrafast electron delocalization occurs by electron tunnelling across the narrow insulating bridge between the Au nanostructures, without material breakdown. In order to quantitatively discuss the tunnelling process, we perform scanning tunnelling microscopy with carrier-envelope phase (CEP)-controlled single-cycle THz electric fields. By applying CEP-controlled THz electric fields to the 1 nm nanogap between a metal nanotip and graphite sample, many electrons could be coherently driven through the quantum tunnelling process, either from the nanotip to the sample or vice versa. The presented concept, namely, electron tunnelling mediated by CEP-controlled single-cycle THz electric fields, can facilitate the development of nanoscale electron manipulation, applicable to next-generation ultrafast nanoelectronics and plasmonic devices.

  10. Fundamental Analysis of Extremely Fast Photonic THz Wireless Communication Systems

    DEFF Research Database (Denmark)

    Yu, Xianbin; Zhang, Xianmin

    This talk will review the recent progress on developing THz communication systems for high speed wireless access, and fundamentally analyze the realistic throughput and accessible wireless range of a THz impulse radio communication link by employing a uni-travelling photodiode (UTC-PD) as emitter...

  11. Mechanisms of THz generation from silver nanoparticle and nanohole arrays

    NARCIS (Netherlands)

    Polyushkin, D.K.; Marton, I.; Racz, P.; Dombi, P.; Hendry, E.; Barnes, William Leslie

    2014-01-01

    We study THz pulses generated from plasmonic metal nanostructures under femtosecond illumination of near-IR light. We find two regimes of excitation, according to the order of the dependence of the THz fluence on the incident near-IR intensity: less then second order at low intensities, changing to

  12. Programmatic perspectives with technical examples for THz materials characterization

    Science.gov (United States)

    Buchwald, Walter

    2011-06-01

    THz technology has a rich history of use in the field of interstellar molecule identification where a variety of molecule specific vibrational and rotational spectroscopic signatures exist and has been aggressively investigated for use in advanced radar applications because of the immediate improvement in object resolution obtained at higher frequencies. Traditionally, high power THz systems have relied upon millimeter wave sources and frequency multiplication techniques to achieve acceptable output power levels, while lower power, table top spectroscopic systems, have relied on broadband incoherent light sources. With the advent of high power lasers, advances in non-linear optics, and new material systems, a number of promising techniques for the generation, detection and manipulation of THz radiation are currently under development and are considered the enabling technologies behind a variety of advanced THz applications. This work presents a programmatic overview of current trends in THz technology of interest to a variety of government organizations. It focuses on those techniques currently under investigation for the generation and detection of THz fields motivated, for example, by such diverse applications as metamaterial spectroscopy, TH imaging, long standoff chem/bio detection and THz communications. Examples of these new techniques will be presented which in turn will motivate the need for the characterization of application specific active and passive THz components.

  13. The OPTHER Project: Progress toward the THz Amplifier

    DEFF Research Database (Denmark)

    Paoloni, C; Brunetti, F; Di Carlo, A

    2011-01-01

    This paper describes the status of the OPTHER (OPtically driven TeraHertz AmplifiERs) project and progress toward the THz amplifier realization. This project represents a considerable advancement in the field of high frequency amplification. The design and realization of a THz amplifier within th...

  14. Material Inspection Using THz and Thermal Wave

    Science.gov (United States)

    Zhang, Cunlin; Mu, Kaijun; Li, Yanhong; Zhang, X.-C.

    2007-03-01

    Terahertz (THz) and thermal wave imaging technologies are complementary inspection modalities for use in non-contact and non-destructive evaluation. Both of them are applied in order to evaluate damages on a variety of composite samples. We will also report the test of a large number of insulation foam panels used in NASA's External Fuel Tank through pulse and CW terahertz systems. The study of defects using the two techniques in selected materials, including metal plates, carbon fibers, glass fibers, carbon silicon composites, etc is also shown.

  15. Seeing Beyond the Painting Surface with Terahertz Time-Domain Imaging (THz-TDI): a signal separation method for extracting images of buried individual layers in paintings

    DEFF Research Database (Denmark)

    Filtenborg, Troels Folke; Skou-Hansen, Jakob; Koch Dandolo, Corinna Ludovica

    2015-01-01

    In this study, the 18C easel painting The Dying Messalina and her Mother, by Nicolai Abildgaard (Statens Museum for Kunst collection, Copenhagen, Denmark), has been investigated by Terahertz Time-Domain Imaging (THz-TDI) in reflection set-up. Despite the validity of traditional deconvolution...... of the acquired THz image. Interfaces between layers of the painting have been successfully imaged, contributing substantially to the understanding of the structure of the painting....

  16. MASTER TELEVISION ANTENNA SYSTEM.

    Science.gov (United States)

    Rhode Island State Dept. of Education, Providence.

    SPECIFICATIONS FOR THE FURNISHING AND INSTALLATION OF TELEVISION MASTER ANTENNA SYSTEMS FOR SECONDARY AND ELEMENTARY SCHOOLS ARE GIVEN. CONTRACTOR REQUIREMENTS, EQUIPMENT, PERFORMANCE STANDARDS, AND FUNCTIONS ARE DESCRIBED. (MS)

  17. Tunable Handset Antenna

    DEFF Research Database (Denmark)

    Barrio, Samantha Caporal Del; Foroozanfard, Ehsan; Morris, Art

    2017-01-01

    With the future LTE auction for TV white spaces at 600 MHz, there is a strong need for efficient handset antennas operating at very low frequencies. This paper shows a tunable antenna covering the LTE bands from 600 MHz to 2.6 GHz. The antenna uses state-of-the-art MEMS tunable capacitors in order...... to reconfigure its operating frequency. In this work, the design mitigates the tuning loss with a tunable extended ground plane. The resulting dual-resonant antenna exhibits a peak total efficiency of -3.9 dB at 600 MHz....

  18. Ultra-wideband antipodal slot antenna with improved radiation performance

    Science.gov (United States)

    Lu, Wen-Jun; Cheung, William S. W.; Cheng, Yong; Zhu, Hong-Bo

    2012-09-01

    A novel antipodal wide-slot antenna for ultra-wideband (UWB) applications is proposed and studied in detail. The antenna is fed by a microstrip line terminated with a rectangular tuning patch. An antipodal structure is employed to improve the radiation performances. The return losses, surface E-field, current distribution, radiation patterns and gains of the antenna are numerically and experimentally investigated. Results show that the proposed antipodal antenna has an impedance bandwidth from 0.79 to 4.0 GHz, which is about 5:1. Compared with conventional rectangular wide-slot antenna, more stable radiation pattern with lower cross-polarisation level and flatter gain variation over a 3:1 bandwidth can be obtained. Thus, the proposed antenna should be more suitable for future UWB-multiple-input multiple-output applications using polarisation diversity than conventional UWB rectangular slot antennas.

  19. A dual-band THz absorber based on graphene sheet and ribbons

    Science.gov (United States)

    Xing, Rui; Jian, Shuisheng

    2018-03-01

    A dual-band graphene absorber is proposed and investigated in this paper. The absorber consists of the gold substrate, the graphene sheet sandwiched by dielectric layers and the array of graphene ribbon placed on the top. The two absorption peaks of the dual-band are 99.8% at 4.95 THz and 99.6% at 9.2 THz, respectively. Due to the characteristic of tunable surface conductivity of graphene, the absorption can be controlled by adjusting the chemical potential of graphene. We also investigate the dependence of the absorption curve of the proposed absorber on the structure parameters. In addition, the structure of the absorber is very simple and it can be manufactured by chemical vapor deposition (CVD).

  20. Band-notched spiral antenna

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, Jae; Chang, John

    2018-03-13

    A band-notched spiral antenna having one or more spiral arms extending from a radially inner end to a radially outer end for transmitting or receiving electromagnetic radiation over a frequency range, and one or more resonance structures positioned adjacent one or more segments of the spiral arm associated with a notch frequency band or bands of the frequency range so as to resonate and suppress the transmission or reception of electromagnetic radiation over said notch frequency band or bands.

  1. Far field focusing for a microwave patch antenna with composite substrate

    Science.gov (United States)

    Wan, Jian; Rybin, Oleg; Shulga, Sergey

    2018-03-01

    Modeling for a compact microwave antenna structure on base of a miniaturized rectangular patch antenna with composite substrate and magnetic superstrates is made in this study by using FDTD simulations. The resonant frequency of the antenna structure is supposed to be 15 GHz. The design of the antenna with composite substrate and without superstrate is made up by using the microwave miniaturization concept for rectangular patch antennas created by first author of this study. The optimal distance between the superstrate and antenna surface is found by using Fabry-Perot cavity theory as maximum values of power directivity and efficiency of the antenna is achieved. The comparative analysis with regard to some far and near field parameters of the above antenna structures and the antenna with dielectric substrate having same value of the relative permittivity is performed.

  2. Nimbus-7 SMMR Antenna Temperatures

    Data.gov (United States)

    National Aeronautics and Space Administration — The SMMR Antenna Temperatures (Nimbus-7) data set consists of antenna temperatures from passive microwave radiometers aboard NOAA's Nimbus-7 satellite. The...

  3. A GaAs/AlAs superlattice autocorrelator for picosecond THz radiation pulses

    NARCIS (Netherlands)

    Winnerl, S.; Pesahl, S.; Schomburg, E.; Grenzer, J.; Renk, K. F.; Pellemans, H. P. M.; van der Meer, A. F. G.; Pavel' ev, D. G.; Koschurinov, Y.; Ignatov, A. A.; Melzer, B.; Ustinov, V.; Ivanov, S.; Kop' ev, P. S.

    1999-01-01

    We report on a GaAs/AlAs, wide-miniband, superlattice autocorrelator for picosecond THz radiation pulses (operated at room temperature); the autocorrelator is based on the THz radiation-induced reduction of current through the superlattice. THz radiation (frequency 7.2 THz) from the FELIX

  4. THz Direct Detector and Heterodyne Receiver Arrays in Silicon Nanoscale Technologies

    Science.gov (United States)

    Grzyb, Janusz; Pfeiffer, Ullrich

    2015-10-01

    The main scope of this paper is to address various implementation aspects of THz detector arrays in the nanoscale silicon technologies operating at room temperatures. This includes the operation of single detectors, detectors operated in parallel (arrays), and arrays of detectors operated in a video-camera mode with an internal reset to support continuous-wave illumination without the need to synchronize the source with the camera (no lock-in receiver required). A systematic overview of the main advantages and limitations in using silicon technologies for THz applications is given. The on-chip antenna design challenges and co-design aspects with the active circuitry are thoroughly analyzed for broadband detector/receiver operation. A summary of the state-of-the-art arrays of broadband THz direct detectors based on two different operation principles is presented. The first is based on the non-quasistatic resistive mixing process in a MOSFET channel, whereas the other relies on the THz signal rectification by nonlinearity of the base-emitter junction in a high-speed SiGe heterojunction bipolar transistor (HBT). For the MOSFET detector arrays implemented in a 65 nm bulk CMOS technology, a state-of-the-art optical noise equivalent power (NEP) of 14 pW/ at 720 GHz was measured, whereas for the HBT detector arrays in a 0.25 μm SiGe process technology, an optical NEP of 47 pW/ at 700 GHz was found. Based on the implemented 1k-pixel CMOS camera with an average power consumption of 2.5 μW/pixel, various design aspects specific to video-mode operation are outlined and co-integration issues with the readout circuitry are analyzed. Furthermore, a single-chip 2 × 2 array of heterodyne receivers for multi-color active imaging in a 160-1000 GHz band is presented with a well-balanced NEP across the operation bandwidth ranging from 0.1 to 0.24 fW/Hz (44.1-47.8 dB single-sideband NF) and an instantaneous IF bandwidth of 10 GHz. In its present implementation, the receiver RF

  5. GPS antenna designs

    Science.gov (United States)

    Laube, Samuel J. P.

    1987-05-01

    Application of the current GPS NAVSTAR system to civilian service requires that a right hand, circularly polarized, -160 dBW spread spectrum signal be received from an orbiting satellite, where the antenna environment is also moving. This presents a design challenge when inexpensive antennas are desired. The intent of this survey is to provide information on the antennas mentioned and to construct and test prototypes to determine whether the choice made by the industry, the quadrifilar helix, is the best. The helix antenna is currently the low cost standard for GPS. Prototype versions were constructed using 12 gauge wire and subminiature coaxial hardline. The constructed antennas were tested using a signal generator and a reference turnstile. A spectrum analyzer was used to measure the level of the received signal.

  6. Ultra-Broadband THz Antireflective Coating with Polymer Composites

    Directory of Open Access Journals (Sweden)

    Bin Cai

    2017-11-01

    Full Text Available Achieving an ultra-broadband range is an essential development direction in terahertz techniques; however, a method to cover the full terahertz band by using a highly efficient antireflection (AR coating that could greatly increase the efficiency of terahertz radiation is still lacking. It is known that structures possessing a graded-index profile can offer a broadband AR effect, and such structures have been widely used, especially in the visible range. In this paper, first, we tuned the refractive index of a cyclo-olefin polymer (COP by using a TiO2 dopant, and a polymer–TiO2 composite with a refractive index of 3.1 was achieved. We then fabricated a surface-relief structure with a graded-index profile by using a hot-embossing method. The structure on the silicon substrate can provide an excellent AR effect, but the working band is still limited by its scale of sag and swell. To obtain an ultra-broadband AR effect, we then proposed a flat six-layer structure; a graded-index profile was obtained by casting epoxy–TiO2 composites in the order of a high index to lower indices. With a very well controlled refractive index and thickness of each layer, we achieved an AR effect of <2% in the ultra-broadband of 0.2–20 THz.

  7. THz Beam Shaper Realizing Fan-Out Patterns

    Science.gov (United States)

    Liebert, K.; Rachon, M.; Siemion, A.; Suszek, J.; But, D.; Knap, W.; Sypek, M.

    2017-08-01

    Fan-out elements create an array of beams radiating at particular angles along the propagation axis. Therefore, they are able to form a matrix of equidistant spots in the far-field diffraction region. In this work, we report on the first fan-out structures designed for the THz range of radiation. Two types of light-dividing fan-out structures are demonstrated: (i) the 3×1 matrix fan-out structure based on the optimized binary phase grating and (ii) the 3×3 fan-out structure designed on the basis of the well-known Dammann grating. The structures were generated numerically and manufactured using the 3D printing technique with polyamide PA12. To obtain equal powers and symmetry of diffracted beams, the computer-aided optimization algorithm was used. Diffractive optical elements designed for 140 and 282 GHz were evaluated experimentally at both these frequencies using illumination with the wavefront coming from the point-like source. Described fan-out elements formed uniform intensity and equidistant energy distribution in agreement with the numerical simulations.

  8. Design and simulations of CAEP THz FEL resonator

    Science.gov (United States)

    Dou, Yuhuan; Shu, Xiaojian; Deng, Derong; Yang, Xingfan; Li, Ming

    2015-02-01

    A high power China Academy of Engineering Physics(CAEP) THz free electron laser (FEL) is designed and optimized in a radiation frequency range of 1~3 THz and average output power of about 10 W. The main work focuses on the optimization of different schemes through physical analysis. The wiggler peak field strength and electron beam energy have been selected with eleven frequencies ranging from 1 THz to 3 THz. It is found that the values of the gain and output power of the cavity are largest at 2.6 THz. So we can test the facility at this frequency. While the value of the output power is less than the design goal at the lower frequency region of about 1.0 THz due to the serious slippage between the electron bunch and radiation pulse. To increase the output power at the lower frequency region, the scheme of elliptical hole-coupling optical resonator is proposed to solve this problem. The simulation results show that the elliptical hole-coupling output is effective and applicable for the THz FEL and the output power can be increased by more than 30%.

  9. THz Imaging by a Wide-band Compact FEL

    CERN Document Server

    Uk Jeong Young; Cheol Lee Byung; Hee-Park, S

    2004-01-01

    We have developed a laboratory-scale users facility with a compact THz FEL. The FEL operates in the wide wavelength range of 100–1200 μm, which corresponds to 0.3-3 THz. THz radiation from the FEL shows well collimated Gaussian spatial distribution and narrow spectral width of 0.3 μm, which is Fourier transform limited by the estimated pulse duration of 20 ps. The main application of the FEL is THz imaging for bio-medical researches. We are developing THz imaging techniques by 2-D scanning, single pulse capturing with the electro-optic method, and 3-D holography. High power, coherent, and pulsed feature of the FEL radiation is expected to show much better performance in advanced THz imaging of 3-D tomography by comparing with incoherent and weak THz sources. By controlling the optical delay between reference beam and scattered light from an object, we can get its 3-D tomography by the holograms. The coherent and pulse length of the FEL beam is measured to be 3-6 mm. In this paper we will show a...

  10. Design of inside cut von koch fractal UWB MIMO antenna

    Science.gov (United States)

    Tharani, V.; Shanmuga Priya, N.; Rajesh, A.

    2017-11-01

    An Inside Cut Hexagonal Von Koch fractal MIMO antenna is designed for UWB applications and its characteristics behaviour are studied. Self-comparative and space filling properties of Koch fractal structure are utilized in the antenna design which leads to the desired miniaturization and wideband characteristics. The hexagonal shaped Von Koch Fractal antenna with Defected Ground Structure (DGS) is designed on FR4 substrate with a compact size of 30mm x 20mm x 1.6mm. The antenna achieves a maximum of -44dB and -51dB at 7.1GHz for 1-element and 2-element case respectively.

  11. Nonlinear THz spectroscopy on n-type GaAs

    Energy Technology Data Exchange (ETDEWEB)

    Gaal, Peter

    2008-06-23

    In this thesis, the ultrafast dynamics of conduction band electrons in semiconductors are investigated by nonlinear terahertz (THz) spectroscopy. In particular, n-doped gallium arsenide samples with doping concentrations in the range of 10{sup 16} cm{sup -3} to 10{sup 17} cm{sup -3} are studied. A novel source for the generation of intense THz radiation is developed which yields single-cycle THz transients with field amplitudes of more then 400 kV/cm. The THz source uses ultrashort optical laser pulses provided by a Ti:sapphire oscillator. In addition, a two-color THz-pump mid-infrared-probe setup is implemented, which allows for two-dimensional time-resolved experiments in the far-infrared wavelength range. Field ionization of neutral shallow donors in gallium arsenide with intense, ultrashort THz pulses and subsequent coherent radiative recombination of electrons to impurity ground states is observed at room temperature. The superradiant decay of the nonlinear polarization results in the emission of a coherent signal with picosecond lifetimes. Such nonlinear signals, which exhibit a lifetime ten times longer than in the linear regime are observed for the first time. At low temperatures and THz field strengths below 5 kV/cm, Rabi flopping on shallow donor transitions is demonstrated. For the first time, the polar electron-LO phonon interaction is directly measured in the quantum kinetic transport regime. Quasi-instantaneous acceleration of conduction band electrons in the polar gallium arsenide lattice by the electric field of intense THz pulses and subsequent probing of the mid-infrared transmission reveals a modulation of the transmission along the THz-mid-infrared delay coordinate with the frequency of the LO phonon. These modulations directly display the relative phase between the electron motion and its surrounding virtual phonon cloud. Quantum kinetic model calculations fully account for the observed phenomena. (orig.)

  12. Reflective terahertz (THz) imaging: system calibration using hydration phantoms

    Science.gov (United States)

    Bajwa, Neha; Garritano, James; Lee, Yoon Kyung; Tewari, Priyamvada; Sung, Shijun; Maccabi, Ashkan; Nowroozi, Bryan; Babakhanian, Meghedi; Sanghvi, Sajan; Singh, Rahul; Grundfest, Warren; Taylor, Zachary

    2013-02-01

    Terahertz (THz) hydration sensing continues to gain traction in the medical imaging community due to its unparalleled sensitivity to tissue water content. Rapid and accurate detection of fluid shifts following induction of thermal skin burns as well as remote corneal hydration sensing have been previously demonstrated in vivo using reflective, pulsed THz imaging. The hydration contrast sensing capabilities of this technology were recently confirmed in a parallel 7 Tesla Magnetic Resonance (MR) imaging study, in which burn areas are associated with increases in local mobile water content. Successful clinical translation of THz sensing, however, still requires quantitative assessments of system performance measurements, specifically hydration concentration sensitivity, with tissue substitutes. This research aims to calibrate the sensitivity of a novel, reflective THz system to tissue water content through the use of hydration phantoms for quantitative comparisons of THz hydration imagery.Gelatin phantoms were identified as an appropriate tissue-mimicking model for reflective THz applications, and gel composition, comprising mixtures of water and protein, was varied between 83% to 95% hydration, a physiologically relevant range. A comparison of four series of gelatin phantom studies demonstrated a positive linear relationship between THz reflectivity and water concentration, with statistically significant hydration sensitivities (p hydration). The THz-phantom interaction is simulated with a three-layer model using the Transfer Matrix Method with agreement in hydration trends. Having demonstrated the ability to accurately and noninvasively measure water content in tissue equivalent targets with high sensitivity, reflective THz imaging is explored as a potential tool for early detection and intervention of corneal pathologies.

  13. Modeling of high gain helical antenna for improved performance ...

    African Journals Online (AJOL)

    The modeling of High Gain Helical Antenna structure is subdivided into three sections : introduction of helical structures ,Numerical analysis, modeling and simulation based on the parameters of helical antenna. The basic foundation software for the research paper is Matlab technical computing software, the modeling were ...

  14. Time-resolved THz studies of carrier dynamics in semiconductors, superconductors, and strongly-correlated electron materials

    Energy Technology Data Exchange (ETDEWEB)

    Kaindl, Robert A.; Averitt, Richard D.

    2006-11-14

    materials occur at lower energies. The terahertz (THz) regime is particularly rich in such fundamental resonances. This includes ubiquitous lattice vibrations and low-energy collective oscillations of conduction charges. In nanoscale materials, band structure quantization also yields novel infrared and THz transitions, including intersubband absorption in quantum wells. The formation of excitons in turn leads to low-energy excitations analogous to inter-level transitions in atoms. In transition-metal oxides, fundamental excitation gaps arise from charge pairing into superconducting condensates and other correlated states. This motivates the use of ultrafast THz spectroscopy as a powerful tool to study light-matter interactions and microscopic processes in nanoscale and correlated-electron materials.A distinct advantage of coherent THz pulses is that the amplitude and phase of the electric field can be measured directly, as the THz fields are coherent with the fs pulses from which they are generated. Using THz time-domain spectroscopy (THz-TDS), both the real and imaginary parts of the response functions (such as the dielectric function) are obtained directly without the need for Kramers?Kronig transforms. The THz response can also be expressed in terms of absorption and refractive index, or as the optical conductivity. The optical conductivity describes the current response of a many-body system to an electric field, an ideal tool to study conducting systems. A second important advantage is the ultrafast time resolution that results from the short temporal duration of the THz time-domain sources. In particular, optical-pump THz-probe spectroscopy enables a delicate probe of the transient THz conductivity after optical photoexcitation. These experiments can provide insight into quasiparticle interactions, phase transitions, or nonequilibrium dynamics. In this chapter we will provide many such examples. Since THz spectroscopy of solids is a quickly expanding field

  15. Vibrational signatures in the THz spectrum of 1,3-DNB: A first-principles and experimental study

    Science.gov (United States)

    Ahmed, Towfiq; Azad, Abul K.; Chellappa, Raja; Higginbotham-Duque, Amanda; Dattelbaum, Dana M.; Zhu, Jian-Xin; Moore, David; Graf, Matthias J.

    2016-05-01

    Understanding the fundamental processes of light-matter interaction is important for detection of explosives and other energetic materials, which are active in the infrared and terahertz (THz) region. We report a comprehensive study on electronic and vibrational lattice properties of structurally similar 1,3-dinitrobenzene (1,3-DNB) crystals through first-principles electronic structure calculations and THz spectroscopy measurements on polycrystalline samples. Starting from reported x-ray crystal structures, we use density-functional theory (DFT) with periodic boundary conditions to optimize the structures and perform linear response calculations of the vibrational properties at zero phonon momentum. The theoretically identified normal modes agree qualitatively with those obtained experimentally in a frequency range up to 2.5 THz and quantitatively at much higher frequencies. The latter frequencies are set by intra-molecular forces. Our results suggest that van der Waals dispersion forces need to be included to improve the agreement between theory and experiment in the THz region, which is dominated by intermolecular modes and sensitive to details in the DFT calculation. An improved comparison is needed to assess and distinguish between intra- and intermolecular vibrational modes characteristic of energetic materials.

  16. Rotational spectrum of formaldehyde reinvestigated using a photomixing THz synthesizer

    Science.gov (United States)

    Eliet, Sophie; Cuisset, Arnaud; Guinet, Mickaël; Hindle, Francis; Mouret, Gaël; Bocquet, Robin; Demaison, Jean

    2012-09-01

    Approximately 60 pure rotational frequency transitions of formaldehyde in its ground state have been measured with sub-MHz uncertainty in the 0.7-1.8 THz frequency range using a photomixing THz synthesizer locked onto a frequency comb. The frequencies associated with previous submillimeter and infrared data have been included in a fit providing a new set of improved molecular parameters. The assignment of each line was checked using the usual statistical diagnostics. Finally, the ability of the continuous-wave spectrometer coupled to a multipass-cell to measure THz rotational transitions of H2CO in the 31, 41 and 61 vibrational states was demonstrated.

  17. Design and Fabrication of a 1 THz Backward Wave Amplifier

    DEFF Research Database (Denmark)

    Paoloni, Claudio; Di Carlo, Aldo; Brunetti, Francesca

    2011-01-01

    require a level of power not achievable by optoelectronic devices at room temperature or by solid-state technology. The recent availability of three-dimensional simulators and high aspect ratio micro-fabrication techniques has stimulated a class of vacuum electron devices operating in the THz regime......The THz frequency range represents a true challenge for designers, fabrication technologies and characterization systems. So far, huge technological obstacles have prohibited any system realization different from laboratory one. Furthermore, most of the applications in the THz frequency range...

  18. Non-Destructive Evaluation (NDE) Applications of THz Radiation

    Science.gov (United States)

    Zimdars, David

    2005-03-01

    The technology and applications of time domain terahertz (THz) imaging to non-destructive evaluation (NDE) will be discussed. THz imaging has shown great promise in 2 and 3 dimensional non-contact inspection of non-conductive materials such as plastics, foam, composites, ceramics, paper, wood and glass. THz imaging employs safe low power non-ionizing electromagnetic pulses, with lateral resolution weapons and explosives will also be discussed, as well as the application of terahertz sensors for high speed industrial process monitoring and quality control.

  19. Superthin resonator dye laser with THz intermode frequency separation

    International Nuclear Information System (INIS)

    Rudych, P D; Surovtsev, N V

    2014-01-01

    Two-color laser irradiation is considered an effective way to pump THz excitations for numerous scientific and applied goals. We present a design for convenient laser source with THz intermode frequency separation. The setup is based on dye laser with superthin resonator pumped by a subnanosecond pulse laser. It was proven that the superthin resonator dye laser is useful, possesses high stability and high energy conversion, and generates narrow laser modes. The ability of this laser to pump CARS processes for THz vibrations is demonstrated. (letter)

  20. Logarithmic Slots Antennas Using Substrate Integrated Waveguide

    Directory of Open Access Journals (Sweden)

    Jahnavi Kachhia

    2015-01-01

    Full Text Available This paper represents new generation of slotted antennas for satellite application where the loss can be compensated in terms of power or gain of antenna. First option is very crucial because it totally depends on size of satellite so we have proposed the high gain antenna creating number of rectangular, trapezoidal, and I shape slots in logarithm size in Substrate Integrated Waveguide (SIW structure. The structure consists of an array of various shape slots antenna designed to operate in C and X band applications. The basic structures have been designed over a RT duroid substrate with dielectric constant of 2.2 and with a thickness of 0.508 mm. Multiple slots array and shape of slot effects have been studied and analyzed using HFSS (High Frequency Structure Simulator. The designs have been supported with its return loss, gain plot, VSWR, and radiation pattern characteristics to validate multiband operation. All the proposed antennas give gain more than 9 dB and return loss better than −10 dB. However, the proposed structures have been very sensitive to their physical dimensions.

  1. Principle of a 'retro reflecting' or 'backfire' LH antenna. A robust efficiently cooled launching structure for LH waves in reactor grade plasmas

    International Nuclear Information System (INIS)

    Bibet, Ph.; Litaudon, X.; Moreau, D.

    1994-01-01

    Up to now, lower hybrid current drive launchers have been made of waveguide arrays. To extrapolate present techniques despite the thermal power load and the mechanical stress, it is necessary to develop an advanced launcher concept which is simpler and more robust. To simplify the antennas between RF vacuum windows and plasma, studies have been carried, for example, the hyperguide for JET, the toroidal oversized waveguide for JT-60U and the poloidal mode converter for Tore Supra. For plasma-facing components, it has been proposed to use diffraction through rod arrays although this suffers from bad coupling per pass. Here a new concept is given which seems to be robust, and should leave enough space for efficient water cooling. The front part near plasma can be easily replaced by remote handling. Its principle is explained, and the description is made. The coupling properties of the proposed structure have been studied by using the SWAN code, and good agreement between the SWAN calculation and the coupling measurement performed at Tore Supra has been reported previously. (K.I.)

  2. Design of Hilbert transformers with tunable THz bandwidths using a reconfigurable integrated optical FIR filter

    Science.gov (United States)

    Ngo, Nam Quoc; Song, Yufeng; Lin, Bo

    2011-02-01

    We present the design and analysis of a wideband and tunable optical Hilbert transformer (OHT) using a tunable waveguide-based finite-impulse response (FIR) filter structure by using the digital filter design method and the Remez algorithm. The tunable Nth-order waveguide-based FIR filter, which simply consists of N delay lines, N tunable couplers, N tunable phase shifters and a combiner, can be tuned, by thermally adjusting the tunable couplers and tunable phase shifters, to tune the bandwidth of an OHT using silica-based planar lightwave circuit (PLC) technology. To demonstrate the effectiveness of the method, the simulation results have an excellent agreement with the theoretical predictions. The tunable OHT can function as a wideband and tunable 90° phase shifter and thus has many potential applications. The two unique features of wideband characteristic (up to ~ 2 THz) and tunable bandwidth (THz tuning range) of the proposed OHT cannot be obtained from the existing OHTs.

  3. THz elastic dynamics in finite-size CoFeB-MgO phononic superlattices

    Energy Technology Data Exchange (ETDEWEB)

    Ulrichs, Henning, E-mail: hulrich@gwdg.de; Meyer, Dennis; Müller, Markus; Wittrock, Steffen; Mansurova, Maria [I. Physical Institute, Georg-August University of Göttingen, Friedrich-Hund-Platz 1, 37077 Göttingen (Germany); Walowski, Jakob; Münzenberg, Markus [Institute of Physics, Ernst-Moritz-Arndt University of Greifswald, Felix-Hausdorff-Str. 6, 17489 Greifswald (Germany)

    2016-10-14

    In this article, we present the observation of coherent elastic dynamics in a nano-scale phononic superlattice, which consists of only 4 bilayers. We demonstrate how ultra-short light pulses with a length of 40 fs can be utilized to excite a coherent elastic wave at 0.535 THz, which persist over about 20 ps. In later steps of the elastic dynamics, modes with frequency of 1.7 THz and above appear. All these modes are related to acoustic band gaps. Thus, the periodicity strongly manifests in the wave physics, although the system under investigation has only a small number of spatial periods. To further illustrate this, we show how by breaking the translational invariance of the superlattice, these features can be suppressed. Discussed in terms of phonon blocking and radiation, we elucidate in how far our structures can be considered as useful building blocks for phononic devices.

  4. Comparison of Thermal Detector Arrays for Off-Axis THz Holography and Real-Time THz Imaging

    Science.gov (United States)

    Hack, Erwin; Valzania, Lorenzo; Gäumann, Gregory; Shalaby, Mostafa; Hauri, Christoph P.; Zolliker, Peter

    2016-01-01

    In terahertz (THz) materials science, imaging by scanning prevails when low power THz sources are used. However, the application of array detectors operating with high power THz sources is increasingly reported. We compare the imaging properties of four different array detectors that are able to record THz radiation directly. Two micro-bolometer arrays are designed for infrared imaging in the 8–14 μm wavelength range, but are based on different absorber materials (i) vanadium oxide; (ii) amorphous silicon; (iii) a micro-bolometer array optimized for recording THz radiation based on silicon nitride; and (iv) a pyroelectric array detector for THz beam profile measurements. THz wavelengths of 96.5 μm, 118.8 μm, and 393.6 μm from a powerful far infrared laser were used to assess the technical performance in terms of signal to noise ratio, detector response and detectivity. The usefulness of the detectors for beam profiling and digital holography is assessed. Finally, the potential and limitation for real-time digital holography are discussed. PMID:26861341

  5. Comparison of Thermal Detector Arrays for Off-Axis THz Holography and Real-Time THz Imaging

    Directory of Open Access Journals (Sweden)

    Erwin Hack

    2016-02-01

    Full Text Available In terahertz (THz materials science, imaging by scanning prevails when low power THz sources are used. However, the application of array detectors operating with high power THz sources is increasingly reported. We compare the imaging properties of four different array detectors that are able to record THz radiation directly. Two micro-bolometer arrays are designed for infrared imaging in the 8–14 μm wavelength range, but are based on different absorber materials (i vanadium oxide; (ii amorphous silicon; (iii a micro-bolometer array optimized for recording THz radiation based on silicon nitride; and (iv a pyroelectric array detector for THz beam profile measurements. THz wavelengths of 96.5 μm, 118.8 μm, and 393.6 μm from a powerful far infrared laser were used to assess the technical performance in terms of signal to noise ratio, detector response and detectivity. The usefulness of the detectors for beam profiling and digital holography is assessed. Finally, the potential and limitation for real-time digital holography are discussed.

  6. Comparison of Thermal Detector Arrays for Off-Axis THz Holography and Real-Time THz Imaging.

    Science.gov (United States)

    Hack, Erwin; Valzania, Lorenzo; Gäumann, Gregory; Shalaby, Mostafa; Hauri, Christoph P; Zolliker, Peter

    2016-02-06

    In terahertz (THz) materials science, imaging by scanning prevails when low power THz sources are used. However, the application of array detectors operating with high power THz sources is increasingly reported. We compare the imaging properties of four different array detectors that are able to record THz radiation directly. Two micro-bolometer arrays are designed for infrared imaging in the 8-14 μm wavelength range, but are based on different absorber materials (i) vanadium oxide; (ii) amorphous silicon; (iii) a micro-bolometer array optimized for recording THz radiation based on silicon nitride; and (iv) a pyroelectric array detector for THz beam profile measurements. THz wavelengths of 96.5 μm, 118.8 μm, and 393.6 μm from a powerful far infrared laser were used to assess the technical performance in terms of signal to noise ratio, detector response and detectivity. The usefulness of the detectors for beam profiling and digital holography is assessed. Finally, the potential and limitation for real-time digital holography are discussed.

  7. Superconducting Solenoid for Superfast THz Spectroscopy

    Science.gov (United States)

    Bragin, A. V.; Khrushchev, S. V.; Kubarev, V. V.; Mezencev, N. A.; Tsukanov, V. M.; Sozinov, G. I.; Shkaruba, V. A.

    This project is related to new spectroscopy method in little-developed THz range. The method is founded on using of a free electron laser (NovoFEL) with high spectral power radiation which can be smoothly tuned in desirable range of spectrum. The objects of research of this method are fast processes in physics, chemical and biological reactions. Uniform magnetic field of 6 T value in the research area can considerably increase possibilities of this method. The magnetic field will modulate radiation of free molecules induction on characteristic frequencies of the Zeeman splitting that gives more possibilities of identification of molecules having even weak magnetic momentum. Moreover, the use of magnetic field allows essentially increase sensitivity of this method due to almost complete separation of weak measuring signals from powerful radiation of the laser. A superconducting solenoid was developed for this method. Its design and peculiarities are described in this paper.

  8. Coupleurs fibres - metasurfaces aux frequences THz

    Science.gov (United States)

    Girard, Martin

    Metamaterials are a class of arficial materials where the electromagnetic properties can be tailored during the design process. Currently demonstrated properties are varied, ranging from frequency filters to enhancement of quentum effects such as photon spin Hall effect. While these materials are mastered from a theoretical point of view, their fabrication is much more complicated. It is generally accepted that metamaterial elements must be under the effective medium limit (Lambda 3D periodical system becomes much more complicated for small elements. For this reason, metamaterials are usually printed in 2D, on a surface, which are called metasurfaces. Generally, these are produced for the THz frequencies (˜ 1012 Hz) or lower to have a large wavelength and thus easy fabrication. Working at THz frequencies also carries additional problems. Absorption in traditional optical mediums is typically large (for exemple, BK7 glass has losses of 20 dB / cm) and powers supplied by THz sources are generally weak ( 100 muW for a THz-TDS standard source). Metasurfaces can thus play an important role by replacing traditional mediums. Moreover, we can use the resonant properties of metamaterials to produce sensors and other devices. Currently, the metasurfaces are used in conjuction with a free-space beam instead of a typical waveguide, which may be problematic when implementing devices. A simple solution to this problem is to use the metamaterial as a standard coupler by placing a waveguide above the metasurface. As stated before, we generally consider metasurfaces as effective mediums, where the permittivity is insensitive to the angle of the incident beam. However, a large amount of publications on this subject shows that this is not respected. This can have a huge impact on properties of a coupler based on such a material. First, modelisation is not a simple 2D mode calculation with a simple expression for permittivity. Second, contra-directional coupling becomes permitted due

  9. Development of SIS Mixers for 1 THz

    Science.gov (United States)

    Zmuidzinas, J.; Kooi, J.; Chattopadhyay, G.; Bumble, B.; LeDuc, H. G.; Stern, J. A.

    1998-01-01

    SIS heterodyne mixer technology based on niobium tunnel junctions has now been pushed to frequencies over 1 THz, clearly demonstrating that the SIS junctions are capable of mixing at frequencies up to twice the energy gap frequency (4 Delta/h). However, the performance degrades rapidly above the gap frequency of niobium (2 Delta/h approx. 700 GHz) due to substantial ohmic losses in the on-chip tuning circuit. To solve this problem, the tuning circuit should be fabricated using a superconducting film with a larger energy gap, such as NbN; unfortunately, NbN films often have a substantial excess surface resistance in the submillimeter band. In contrast, the SIS mixer measurements we present in this paper indicate that the losses for NbTiN thin films can be quite low.

  10. Infrared and THz spectroscopy of nanostructured dielectrics

    Directory of Open Access Journals (Sweden)

    Jan Petzelt

    2009-09-01

    Full Text Available Results achieved using the infrared/THz spectroscopy of various inhomogeneous dielectrics in the Department of Dielectrics, Institute of Physics, Prague, during the last decade are briefly reviewed. The discussion concerns high-permittivity ceramics with inevitable low-permittivity dead layers along the grain boundaries, relaxor ferroelectrics with highly anisotropic polar nano-regions, classical matrix-type composites, core-shell composites, filled nanoporous glasses, polycrystalline and epitaxial thin films, heterostructures and superlattices on dielectric substrates. The analysis using models based on the effective medium approach is discussed. The importance of depolarizing field and of the percolation of components on the effective ac dielectric response and the excitations contributing to it are emphasized.

  11. Closely Mounted Compact Wideband Diversity Antenna for Mobile Phone Applications

    Directory of Open Access Journals (Sweden)

    Bunggil Yu

    2012-01-01

    Full Text Available Here a compact wideband diversity antenna covering the PCS/UMTS/WiMAX bands with high isolation and low enveloped correlation coefficient (ECC is proposed. To widen the bandwidth, the proposed antenna uses a structure with a gap-coupled feed and an inductively shorted line that has capacitive compensation between the radiator and the ground plane. Also, a suspended line with a parasitic element is used to enhance the isolation between the two antennas.

  12. Emitter-Wrap-Through Photovoltaic Dipole Antenna with Solar Concentrator

    OpenAIRE

    Roo Ons, Maria; Shynu, S.; Ammann, Max; McCormack, Sarah; Norton, Brian

    2009-01-01

    A novel photovoltaic dipole antenna employing a solar concentrator as a reflector is proposed. Four identical emitter-wrap-through rear contact solar cells connected in series as a folded dipole are simultaneously used for power generation and as the antenna radiating element, which is located in the focal line of a parabolic solar concentrator. The parabolic structure acts as a solar concentrator for the photovoltaic cells as well as a reflector for the folded dipole antenna. Full-wave elect...

  13. Plasmonic superradiant antennas

    Science.gov (United States)

    Tayebi, Amin; Rice, Scott A.

    2017-12-01

    Non-Hermitian Hamiltonians have long been utilized in the investigation of open quantum systems in various disciplines, such as the shell model in nuclear physics and solid state quantum computing devices in condensed matter physics to name a few. The hallmark of these systems is the sharp redistribution of decay widths and the segregation of short-lived "superradiant" states and long-lived "trapped" states at sufficiently strong interaction with the continuum. Here we extend the applicability of the non-Hermitian Hamiltonian framework to systems of spherical metallic nano particles where light can be manipulated via surface plasmonic resonances. The signature of superradiance emerges when the interaction between adjacent optical nanoantennas occurs through a single continuum channel, resulting in eigenmodes with distinct properties: superradiant states with enhanced radiation and confined dark modes for which radiation is greatly suppressed. A new type of superradiance occurs in waveguide-like structures that are coupled to an external world such as laser sources and measurement probes. In this case, the neighboring spheres interact indirectly through a common continuum channel provided by the external device, resulting in the same superradiance transition phenomenon. The effect of superradiant states on energy transmission through a one dimensional chain of spheres is also considered, with applications to optical-frequency nano-scale antennas and waveguide-like structures.

  14. Enhanced THz resonance based on the coupling between Fabry–Perot oscillation and dipolar-like resonance in a metamaterial surface cavity

    International Nuclear Information System (INIS)

    Zhang, Yaxin; Xu, Gaiqi; Qiao, Shen; Zhou, Yucong; Wu, Zhenhua; Yang, Ziqiang

    2015-01-01

    We presented an enhanced resonance with ultra-wide band in the terahertz (THz) regime in a THz metamaterial system composed of a pair of circular rings arrays which act as two opposite mirrors. The two opposite mirrors, both of which will induce a dipolar-like resonance under the incident wave, together with the gap between them will constitute a Fabry–Perot cavity which contributes to a Fabry–Perot oscillation in the system. These two kinds of resonant modes, the dipolar-like resonance and Fabry–Perot oscillation, can be coupled with each other in an optimized structure, which leads to an enhanced electromagnetic resonance. From the experimental results, it can be found that such coupling leads to a nearly zero transmission zone with 0.12 THz bandwidth which is much better than individual conventional metamaterial system. This coupling mechanism could provide a new way for the realization of strong resonance, which shows great potential for THz pass-band or stop-band filters, THz resonators, THz absorbers, frequency selective devices and so on. (paper)

  15. Smart antennas in aerospace applications

    NARCIS (Netherlands)

    Verpoorte, Jaco; Schippers, Harmen; Roeloffzen, C.G.H.; Marpaung, D.A.I.

    2010-01-01

    The interest in Smart Antennas for aerospace applications is growing. This paper describes smart antennas which can be used on aircraft. Two aerospace applications are discussed in more detail: a phased array antenna with optical beam forming and a large vibrating phased array antenna with

  16. Modelling, fabrication and characterisation of THz fractal meta-materials

    DEFF Research Database (Denmark)

    Xiao, S.; Zhou, L.; Malureanu, Radu

    2011-01-01

    We present theoretical predictions, fabrication procedure and characterisation results of fractal metamaterials for the THz frequency range. The characterisation results match well the predicted response thus validating both the fabrication procedure as well as the simulation one. Such systems show...

  17. Antennas from theory to practice

    CERN Document Server

    Huang, Yi

    2008-01-01

    Practical, concise and complete reference for the basics of modern antenna design Antennas: from Theory to Practice discusses the basics of modern antenna design and theory. Developed specifically for engineers and designers who work with radio communications, radar and RF engineering, this book offers practical and hands-on treatment of antenna theory and techniques, and provides its readers the skills to analyse, design and measure various antennas. Key features: Provides thorough coverage on the basics of transmission lines, radio waves and propag

  18. Buoyant Cable Antenna System

    National Research Council Canada - National Science Library

    Gerhard, Erich M

    2008-01-01

    .... For instance, in one embodiment two oppositely extending curves each float and each are pressed by the water in a balanced manner to provide a stable platform for one or more antennas which can be...

  19. Coaxial phased array antenna

    Science.gov (United States)

    Ellis, H., Jr.

    1980-08-01

    A coaxial antenna array for communicating circularly polarized electromagnetic radiation is disclosed. A pair of open ended antenna cavities is coaxially constructed and operates by excitation of linear radiation elements arranged within each of the cavities. A pair of crossed dipole radiation devices is centered within the inner cavity and operated by means of a phase shifting network circuit to transmit as well as receive circularly polarized radiation. Four monopole radiation devices are symmetrically arranged to operate in the outer cavity in phase quadrature by means of the phase shifting network circuit to both transmit and receive circularly polarized electromagnetic radiation. Combined operation of the two antenna cavities with a 180 deg phase differential between the fields related to the two antenna cavities provides a broad beam, relatively wide frequency bandwidth communication capability. Particular embodiments disclosed feature a generally square cavity array as well as a circular cavity array.

  20. Microwave antenna holography

    Science.gov (United States)

    Rochblatt, David J.; Seidel, Boris L.

    1992-01-01

    This microwave holography technique utilizes the Fourier transform relation between the complex far field radiation pattern of an antenna and the complex aperture field distribution. Resulting aperture phase and amplitude distribution data can be used to precisely characterize various crucial performance parameters, including panel alignment, panel shaping, subreflector position, antenna aperture illumination, directivity at various frequencies, and gravity deformation effects. The methodology of data processing presented here was successfully applied to the Deep Space Network (DSN) 34-m beam waveguide antennas. The antenna performance was improved at all operating frequencies by reducing the main reflector mechanical surface rms error to 0.43 mm. At Ka-band (32 GHz), the estimated improvement is 4.1 dB, resulting in an aperture efficiency of 52 percent. The performance improvement was verified by efficiency measurements and additional holographic measurements.

  1. Investigation of graphene based miniaturized terahertz antenna for novel substrate materials

    Directory of Open Access Journals (Sweden)

    Rajni Bala

    2016-03-01

    Full Text Available The selection of appropriate substrate material acts as a performance regulator for miniaturized graphene patch antenna. The substrate material not only controls the transport properties of graphene but also influences the resonant properties of the graphene patch antenna. The edge fed microstrip line graphene based rectangular patch antenna is designed here for operating in the frequency range 2.67–2.92 THz for wireless applications. The performance is investigated for silicon nitride, aluminum oxide, boron nitride, silica and quartz substrate materials on the basis of return loss, voltage standing wave ratio (VSWR, absorption cross section, bandwidth and radiation efficiency. The comparison of results shows that silicon nitride exhibits overall excellent performance by the virtue of having higher bandwidth and radiation efficiency as compared to other chosen substrate materials.

  2. Timing jitter correction for THz-TDS measurements of graphene

    DEFF Research Database (Denmark)

    Whelan, Patrick Rebsdorf; Iwaszczuk, Krzysztof; Bøggild, Peter

    2016-01-01

    We discuss how noncontact, quantitative large-area mapping of the conductance of thin films requires delicate corrections in order to deduce electrical properties such as graphene mobility from THz-TDS measurements.......We discuss how noncontact, quantitative large-area mapping of the conductance of thin films requires delicate corrections in order to deduce electrical properties such as graphene mobility from THz-TDS measurements....

  3. THz induced nonlinear absorption in ZnTe

    DEFF Research Database (Denmark)

    Pedersen, Pernille Klarskov; Jepsen, Peter Uhd

    2015-01-01

    Absorption spectra of ZnTe during strong-field THz interaction are investigated. Bleaching of the difference phonon modes below the fundamental TO mode is observed when field strengths higher than 4 MV/cm are applied.......Absorption spectra of ZnTe during strong-field THz interaction are investigated. Bleaching of the difference phonon modes below the fundamental TO mode is observed when field strengths higher than 4 MV/cm are applied....

  4. Microwave RF antennas and circuits nonlinearity applications in engineering

    CERN Document Server

    Aluf, Ofer

    2017-01-01

    This book describes a new concept for analyzing RF/microwave circuits, which includes RF/microwave antennas. The book is unique in its emphasis on practical and innovative microwave RF engineering applications. The analysis is based on nonlinear dynamics and chaos models and shows comprehensive benefits and results. All conceptual RF microwave circuits and antennas are innovative and can be broadly implemented in engineering applications. Given the dynamics of RF microwave circuits and antennas, they are suitable for use in a broad range of applications. The book presents analytical methods for microwave RF antennas and circuit analysis, concrete examples, and geometric examples. The analysis is developed systematically, starting with basic differential equations and their bifurcations, and subsequently moving on to fixed point analysis, limit cycles and their bifurcations. Engineering applications include microwave RF circuits and antennas in a variety of topological structures, RFID ICs and antennas, micros...

  5. Integrated millimeter-wave corner-cube antennas

    Science.gov (United States)

    Gearhart, Steven S.; Ling, Curtis C.; Rebeiz, Gabriel M.

    1991-01-01

    An integrated corner-reflector antennas has been designed, fabricated, and measured at millimeter-wave frequencies. The structure consists of a traveling-wave antenna integrated on a 1.2-micron dielectric membrane, and suspended in a longitudinal cavity etched in a silicon wafer. A novel traveling wave antenna design, the modified-bend antenna, with an antenna length of 1.2 lambda and spacing 0.96 lambda from the apex, results in a wideband input impedance centered at 140 Ohm and low cross-polarization levels. Measurements at 180-270 GHz show a well-defined pattern with low sidelobe levels, and a main-beam efficiency of 93 percent and 83 percent at 180 and 222 GHz, respectively. The monolithic approach allows the integration of a matching network and a Schottky-diode or SIS detector at the base of the antenna to yield a low-noise monolithic millimeter-wave receiver.

  6. Multiple-Active Multiple-Passive Antenna Systems and Applications

    DEFF Research Database (Denmark)

    Tsakalaki, Elpiniki

    2013-01-01

    -passive (MAMP) antenna topologies, as explained in Sect. 8.1. Then, Sect. 8.2 proposes MAMP antenna structures with application to reconfigurable MIMO transmission in the presence of antenna mutual coupling under poor scattering channel conditions. For this purpose, the section presents an adaptive MAMP antenna...... satisfactory performance even in poor scattering environments whereas a significant part of the mutual information that is lost owing to the spatial correlation and the electromagnetic coupling is successfully retrieved. Section 8.3 extends our communication scenario to account for multiuser diversity systems......, describing novel parasitic antenna-assisted switched beam array architectures for enhanced selection combining with application to the downlink of cellular systems exploiting multiuser diversity. Specifically, this section deals with the problem of the poor performance of antenna selection for compact user...

  7. Compact Ultra-Wideband Antenna for Portable Devices

    International Nuclear Information System (INIS)

    Kasi, B; Ping, L C; Chakrabarty, C K

    2013-01-01

    This article presents a compact ultra-wideband (UWB) antenna for wireless dongle devices. The printed monopole antenna, with the size of 15 mm × 30 mm, has an impedance bandwidth ranges from 2.9 to 13 GHz. The proposed structure comprises of a hexagonal radiator fed by a microstrip line with a modified ground plane. Such a design can be easily integrated with wireless universal serial bus (USB) devices. Having stable radiation patterns and constant gain within the UWB spectrum are significant characteristics of this antenna. The time domain studies on the designed antenna indicate reduced ringing effect for impulse excitation across the band of interest.

  8. Compact Ultra-Wideband Antenna for Portable Devices

    Science.gov (United States)

    Kasi, B.; Ping, L. C.; Chakrabarty, C. K.

    2013-06-01

    This article presents a compact ultra-wideband (UWB) antenna for wireless dongle devices. The printed monopole antenna, with the size of 15 mm × 30 mm, has an impedance bandwidth ranges from 2.9 to 13 GHz. The proposed structure comprises of a hexagonal radiator fed by a microstrip line with a modified ground plane. Such a design can be easily integrated with wireless universal serial bus (USB) devices. Having stable radiation patterns and constant gain within the UWB spectrum are significant characteristics of this antenna. The time domain studies on the designed antenna indicate reduced ringing effect for impulse excitation across the band of interest.

  9. Design of a Tuning Fork type UWB Patch Antenna

    OpenAIRE

    A. H. M. Zahirul Alam; Rafiqul Islam; Sheroz Khan

    2007-01-01

    In this paper a tuning fork type structure of Ultra Wideband (UWB) antenna is proposed. The antenna offers excellent performance for UWB system, ranging from 3.7 GHz to 13.8 GHz. The antenna exhibits a 10 dB return loss bandwidth over the entire frequency band. The rectangular patch antenna is designed on FR4 substrate and fed with 50 ohms microstrip line by optimizing the width of partial ground, the width and position of the feedline to operate in UWB. The rectangular p...

  10. Hybrid Plasmonic Bullseye Antennas for Efficient Photon Collection

    DEFF Research Database (Denmark)

    Andersen, Sebastian Kim Hjælm

    2018-01-01

    We propose highly efficient hybrid plasmonic bullseye antennas for collecting photon emission from nm sized quantum emitters. In our approach, the emitter radiation is coupled to surface plasmon polaritons that are consequently converted into highly directional out-of-plane emission. The proposed...... enhancement of close to 20 at the design wavelength. Hybrid antenna structures were fabricated by standard electron-beam lithography without the use of lossy adhesion layers that might be detrimental to antenna performance. The fabricated antennas remained undamaged at saturation laser powers exhibiting...... resonantly enhanced, highly directional emission at the design wavelength of 670nm, whose characteristics are in excellent agreement with our numerical simulations...

  11. Electric-Coupled Antenna for Hearing-Instrument Applications

    DEFF Research Database (Denmark)

    Færch, Laust; Kvist, Søren H.; Thaysen, Jesper

    2016-01-01

    An electrically small, electric coupled antenna that operates at the 2.4 GHz ISM band has been designed for hearing instrument applications. The antenna consists of a driven monopole and a coupled structure that is separated by an air gap. The input reflection coefficient S11 is measured...... and compared to the simulated results. Investigation of the antenna center frequency, reflection coefficient, and efficiency sensitivity to the position of the coupled element is performed. Simulated and measured results suggest that the antenna is a suitable candidate for hearing instrument applications....

  12. Analysis and Design of a Multi-Frequency Microstrip Antenna Based on a PBG Substrate

    Directory of Open Access Journals (Sweden)

    YANG Hong

    2014-06-01

    Full Text Available Based on the C-shaped microstrip slot antenna, a new photonic band gap substrate for multi-frequency microstrip slot antenna is designed. The antenna has a groove been dug below the radiation plate, within which the radiation plate is placed, and air triangular prism column gaps with different height are placed in the substrate periodically. Numerical simulation is performed for the antenna with Ansoft HFSS10.0, which is a kind of simulation software based on Finite Element Method. Comparing with the C-shaped microstrip slot antenna, the resonant frequency of the antenna was reduced by 230 MHz, and the low frequency bandwidth was increased from 12.63 % to 18.95 %, both the radiation and multi-frequency characteristics of this proposed antenna are improved. The result demonstrates that the structure is efficient in improving the antenna gain and radiation directivity by suppressing surface wave of the microstrip antenna.

  13. Vectorial diffraction properties of THz vortex Bessel beams.

    Science.gov (United States)

    Wu, Zhen; Wang, Xinke; Sun, Wenfeng; Feng, Shengfei; Han, Peng; Ye, Jiasheng; Yu, Yue; Zhang, Yan

    2018-01-22

    A vortex Bessel beam combines the merits of an optical vortex and a Bessel beam, including a spiral wave front and a non-diffractive feature, which has immense application potentials in optical trapping, optical fabrication, optical communications, and so on. Here, linearly and circularly polarized vortex Bessel beams in the terahertz (THz) frequency range are generated by utilizing a THz quarter wave plate, a spiral phase plate, and Teflon axicons with different opening angles. Taking advantage of a THz focal-plane imaging system, vectorial diffraction properties of the THz vortex Bessel beams are comprehensively characterized and discussed, including the transverse (Ex, Ey) and longitudinal (Ez) polarization components. The experimental phenomena are accurately simulated by adopting the vectorial Rayleigh diffraction integral. By varying the opening angle of the axicon, the characteristic parameters of these THz vortex Bessel beams are exhibited and compared, including the light spot size, the diffraction-free range, and the phase evolution process. This work provides the precise experimental and theoretical bases for the comprehension and application of a THz vortex Bessel beam.

  14. Computational Investigations of THz Transmittance in the Atmosphere

    Directory of Open Access Journals (Sweden)

    Yang Xingyu

    2016-01-01

    Full Text Available With the recent scientific advancements in Terahertz (THz wave propagation and reception technology, there has been significant development in new possibilities for using THz waves – offering new possibilities in THz detection and ranging. A first foundational step toward this goal is to better understand THz transmittance in the turbulent atmosphere. In this project, a frequency modulation pattern of THz waves was created by utilizing a system of shifting frequency based on temperature, air humidity, and distance of transmission. The total path loss of the wave in air, based on the wave spread and molecular absorption, was then modeled using radiative transfer theory, onto a set of JavaHAWK filtered-HITRAN data representative of an air sample. This data was used to generate a path loss matrix, which was then used to optimize frequency of transmission for the specific conditions. The concept to be evaluated is whether adaptive frequency modulated THz might usefully decrease transmission losses by adjusting to atmospheric conditions (such as local variations in temperature and humidity.

  15. The Folded Horn Antenna

    Science.gov (United States)

    Farr, E. G.; Bowen, L. H.; Baum, C. E.; Prather, W. D.

    Antennas for radiating high-power mesoband (medium-bandwidth) electromagnetic signals are critical to the mission of upsetting electronics at a distance. When operated at frequencies of a few hundred megahertz, RF weapons require highly efficient antennas that can fit into a small volume. Most of the existing antennas, such as pyramidal horns, are too large to fit onto certain platforms of interest. To address this challenge, we investigate the folded horn, which has aperture dimensions of 0.5 × 2 wavelengths, and a depth of 1.5-2 wavelengths. This antenna has a nearly focused aperture field, due to a parabolic fold in the H-plane. We report here on the fabrication and testing of the first folded horn, operating at 3 GHz. After a number of iterations, we obtained a realized gain of at least 10 dBi over 3-5 GHz, an aperture efficiency of 80%, and a return loss below -10 dB over 2.8-3.35 GHz. This design could be adapted to high-voltages, and it could work well in a two-antenna array, with two antennas positioned back to back, driven by a differential source.

  16. Broadband modulation of terahertz waves through electrically driven hybrid bowtie antenna-VO2 devices.

    Science.gov (United States)

    Han, Chunrui; Parrott, Edward P J; Humbert, Georges; Crunteanu, Aurelian; Pickwell-MacPherson, Emma

    2017-10-05

    Broadband modulation of terahertz (THz) light is experimentally realized through the electrically driven metal-insulator phase transition of vanadium dioxide (VO 2 ) in hybrid metal antenna-VO 2 devices. The devices consist of VO 2 active layers and bowtie antenna arrays, such that the electrically driven phase transition can be realized by applying an external voltage between adjacent metal wires extended to a large area array. The modulation depth of the terahertz light can be initially enhanced by the metal wires on top of VO 2 and then improved through the addition of specific bowties in between the wires. As a result, a terahertz wave with a large beam size (~10 mm) can be modulated within the measurable spectral range (0.3-2.5 THz) with a frequency independent modulation depth as high as 0.9, and the minimum amplitude transmission down to 0.06. Moreover, the electrical switch on/off phase transition depends very much on the size of the VO 2 area, indicating that smaller VO 2 regions lead to higher modulation speeds and lower phase transition voltages. With the capabilities in actively tuning the beam size, modulation depth, modulation bandwidth as well as the modulation speed of THz waves, our study paves the way in implementing multifunctional components for terahertz applications.

  17. Possible standoff detection of ionizing radiation using high-power THz electromagnetic waves

    Science.gov (United States)

    Nusinovich, Gregory S.; Sprangle, Phillip; Romero-Talamas, Carlos A.; Rodgers, John; Pu, Ruifeng; Kashyn, Dmytro G.; Antonsen, Thomas M., Jr.; Granatstein, Victor L.

    2012-06-01

    Recently, a new method of remote detection of concealed radioactive materials was proposed. This method is based on focusing high-power short wavelength electromagnetic radiation in a small volume where the wave electric field exceeds the breakdown threshold. In the presence of free electrons caused by ionizing radiation, in this volume an avalanche discharge can then be initiated. When the wavelength is short enough, the probability of having even one free electron in this small volume in the absence of additional sources of ionization is low. Hence, a high breakdown rate will indicate that in the vicinity of this volume there are some materials causing ionization of air. To prove this concept a 0.67 THz gyrotron delivering 200-300 kW power in 10 microsecond pulses is under development. This method of standoff detection of concealed sources of ionizing radiation requires a wide range of studies, viz., evaluation of possible range, THz power and pulse duration, production of free electrons in air by gamma rays penetrating through container walls, statistical delay time in initiation of the breakdown in the case of low electron density, temporal evolution of plasma structure in the breakdown and scattering of THz radiation from small plasma objects. Most of these issues are discussed in the paper.

  18. A Rectangular Planar Spiral Antenna for GIS Partial Discharge Detection

    Directory of Open Access Journals (Sweden)

    Xiaoxing Zhang

    2014-01-01

    Full Text Available A rectangular planar spiral antenna sensor was designed for detecting the partial discharge in gas insulation substations (GIS. It can expediently receive electromagnetic waves leaked from basin-type insulators and can effectively suppress low frequency electromagnetic interference from the surrounding environment. Certain effective techniques such as rectangular spiral structure, bow-tie loading, and back cavity structure optimization during the antenna design process can miniaturize antenna size and optimize voltage standing wave ratio (VSWR characteristics. Model calculation and experimental data measured in the laboratory show that the antenna possesses a good radiating performance and a multiband property when working in the ultrahigh frequency (UHF band. A comparative study between characteristics of the designed antenna and the existing quasi-TEM horn antenna was made. Based on the GIS defect simulation equipment in the laboratory, partial discharge signals were detected by the designed antenna, the available quasi-TEM horn antenna, and the microstrip patch antenna, and the measurement results were compared.

  19. Combline antennas for launching traveling fast waves

    International Nuclear Information System (INIS)

    Moeller, C.P.; Gould, R.W.; Phelps, D.A.; Pinsker, R.I.

    1994-01-01

    The combline structure shows promise for launching traveling fast magnetosonic waves with adjustable n parallel (3 ≤ n parallel ≤ 6) for current drive. In this paper, the dispersion and damping properties of the combline antenna with and without a Faraday shield are given. The addition of a Faraday shield which eliminates the electrostatic coupling between current straps as well as between the straps and plasma offers the advantage of eliminating the need for the lumped capacitors which are otherwise required with this structure. The results of vacuum dispersion and damping measurements on a low power model antenna are also given. (author)

  20. Covering THz Gap using photomixers techonologies: arrays and new antenna topologies

    OpenAIRE

    Rivera Lavado, Alejandro

    2016-01-01

    Mención Internacional en el título de doctor El objetivo de esta tesis es el diseño y construcción de generadores de señal de terahercios basados en fotomezcladores de bajo coste y que funcionen a temperatura ambiente. Como se explica en la introducción, existen muchas aplicaciones potenciales a frecuencias comprendidas entre los 100 GHz y 1.000 GHz. Propuestas en el campo de la seguridad, radioastronomía y medicina, entre otros, han sido consideradas y evaluadas. Algunas...

  1. MULTIBAND MILLIMETER WAVE T-SHAPED ANTENNA WITH ...

    African Journals Online (AJOL)

    The return loss impedance bandwidth of 5GHz for the first band, 8.4GHz for the second band and 5GHz for the third band was obtained. The proposed antenna was analyzed using Ansoft High Frequency Structure Simulator (HFSS) and MATLAB 2013. Radiation characteristics of this patch antenna are observed at various ...

  2. Small and Robust Antennas for Concrete Embedded Sensors

    DEFF Research Database (Denmark)

    Rindorf, Lars; Jakobsen, Kaj Bjarne

    2009-01-01

    We study a small antenna for a structural health monitoring sensor. The sensor is cast into concrete. The sensor monitors the humidity and temperature of the concrete, which is a harsh environment. From measured material parameters of the concrete we estimate the signal loss and the antenna detun...

  3. Antenna and RF Subsystem Integration in Cellular Communications

    DEFF Research Database (Denmark)

    Herrero, Pablo; Bahramzy, Pevand; Svendsen, Simon

    2014-01-01

    matching, depending on the system’s requirements. A particular antenna concept that implements two different wireless systems (LTE and Wi-Fi) is outlined in a subsequent section. Such a structure can reduce the volume required for antennas on a mobile device. The article concludes with an example of how...

  4. Modeling and Optimizing Antennas for Rotational Spectroscopy Applications

    Directory of Open Access Journals (Sweden)

    Z. Raida

    2006-12-01

    Full Text Available In the paper, dielectric and metallic lenses are modeled and optimized in order to enhance the gain of a horn antenna in the frequency range from 60 GHz to 100 GHz. Properties of designed lenses are compared and discussed. The structures are modeled in CST Microwave Studio and optimized by Particle Swarm Optimization (PSO in order to get required antenna parameters.

  5. Double Ring Antenna Design for MIMO Application in Mobile Terminals

    DEFF Research Database (Denmark)

    Zhao, Kun; Zhang, Shuai; Ying, Zhinong

    2015-01-01

    In this paper, We present a MIMO bezel antenna design composed by a seamless double metal ring structure. The MIMO antenna mainly operates in the loop mode and can cover the majority of globe cellular bands. Good efficiencies (>-4dB) and a low envelope correlation coefficient (<0.5) are achieved,...

  6. Metamaterial Inspired Microstrip Antenna Investigations Using Metascreens

    Directory of Open Access Journals (Sweden)

    Muhammad Tauseef Asim

    2015-01-01

    Full Text Available A dual layer periodically patterned metamaterial inspired antenna on a low cost FR4 substrate is designed, simulated, fabricated, and tested. The eigenmode dispersion simulations are performed indicating the left handed metamaterial characteristics and are tunable with substrate permittivity. The same metamaterial unit cell structure is utilized to fabricate a metascreen. This metascreen is applied below the proposed metamaterial antenna and next used as superstrate above a simple patch to study the effects on impedance bandwidth, gain, and radiation patterns. The experimental results of these antennas are very good and closely match with the simulations. More importantly, the resonance for the proposed metamaterial antenna with metascreen occurs at the left handed (LH eigenfrequency of the metamaterial unit cell structure. The measured −10 dB bandwidths are 14.56% and 22.86% for the metamaterial antenna with single and double metascreens, respectively. The metascreens over the simple patch show adjacent dual band response. The first and second bands have measured −10 dB bandwidths of 9.6% and 16.66%. The simulated peak gain and radiation efficiency are 1.83 dBi and 74%, respectively. The radiation patterns are also very good and could be useful in the UWB wireless applications.

  7. Antenna for Ultrawideband Channel Sounding

    DEFF Research Database (Denmark)

    Zhekov, Stanislav Stefanov; Tatomirescu, Alexandru; Pedersen, Gert F.

    2016-01-01

    A novel compact antenna for ultrawideband channel sounding is presented. The antenna is composed of a symmetrical biconical antenna modified by adding a cylinder and a ring to each cone. A feeding coaxial cable is employed during the simulations in order to evaluate and reduce its impact on the a......A novel compact antenna for ultrawideband channel sounding is presented. The antenna is composed of a symmetrical biconical antenna modified by adding a cylinder and a ring to each cone. A feeding coaxial cable is employed during the simulations in order to evaluate and reduce its impact...

  8. Modeling of compact loop antennas

    International Nuclear Information System (INIS)

    Baity, F.W.

    1987-01-01

    A general compact loop antenna model which treats all elements of the antenna as lossy transmission lines has been developed. In addition to capacitively-tuned resonant double loop (RDL) antennas the model treats stub-tuned resonant double loop antennas. Calculations using the model have been compared with measurements on full-scale mockups of resonant double loop antennas for ATF and TFTR in order to refine the transmission line parameters. Results from the model are presented for RDL antenna designs for ATF, TFTR, Tore Supra, and for the Compact Ignition Tokamak

  9. THz Spectroscopy and Spectroscopic Database for Astrophysics

    Science.gov (United States)

    Pearson, John C.; Drouin, Brian J.

    2006-01-01

    Molecule specific astronomical observations rely on precisely determined laboratory molecular data for interpretation. The Herschel Heterodyne Instrument for Far Infrared, a suite of SOFIA instruments, and ALMA are each well placed to expose the limitations of available molecular physics data and spectral line catalogs. Herschel and SOFIA will observe in high spectral resolution over the entire far infrared range. Accurate data to previously unimagined frequencies including infrared ro-vibrational and ro-torsional bands will be required for interpretation of the observations. Planned ALMA observations with a very small beam will reveal weaker emission features requiring accurate knowledge of higher quantum numbers and additional vibrational states. Historically, laboratory spectroscopy has been at the front of submillimeter technology development, but now astronomical receivers have an enormous capability advantage. Additionally, rotational spectroscopy is a relatively mature field attracting little interest from students and funding agencies. Molecular data base maintenance is tedious and difficult to justify as research. This severely limits funding opportunities even though data bases require the same level of expertise as research. We report the application of some relatively new receiver technology into a simple solid state THz spectrometer that has the performance required to collect the laboratory data required by astronomical observations. Further detail on the lack of preparation for upcoming missions by the JPL spectral line catalog is given.

  10. Cricket antennae shorten when bending (Acheta domesticus L.).

    Science.gov (United States)

    Loudon, Catherine; Bustamante, Jorge; Kellogg, Derek W

    2014-01-01

    Insect antennae are important mechanosensory and chemosensory organs. Insect appendages, such as antennae, are encased in a cuticular exoskeleton and are thought to bend only between segments or subsegments where the cuticle is thinner, more flexible, or bent into a fold. There is a growing appreciation of the dominating influence of folds in the mechanical behavior of a structure, and the bending of cricket antennae was considered in this context. Antennae will bend or deflect in response to forces, and the resulting bending behavior will affect the sensory input of the antennae. In some cricket antennae, such as in those of Acheta domesticus, there are a large number (>100) of subsegments (flagellomeres) that vary in their length. We evaluated whether these antennae bend only at the joints between flagellomeres, which has always been assumed but not tested. In addition we questioned whether an antenna undergoes a length change as it bends, which would result from some patterns of joint deformation. Measurements using light microscopy and SEM were conducted on both male and female adult crickets (Acheta domesticus) with bending in four different directions: dorsal, ventral, medial, and lateral. Bending occurred only at the joints between flagellomeres, and antennae shortened a comparable amount during bending, regardless of sex or bending direction. The cuticular folds separating antennal flagellomeres are not very deep, and therefore as an antenna bends, the convex side (in tension) does not have a lot of slack cuticle to "unfold" and does not lengthen during bending. Simultaneously on the other side of the antenna, on the concave side in compression, there is an increasing overlap in the folded cuticle of the joints during bending. Antennal shortening during bending would prevent stretching of antennal nerves and may promote hemolymph exchange between the antenna and head.

  11. Cricket antennae shorten when bending (Acheta domesticus L.

    Directory of Open Access Journals (Sweden)

    Catherine eLoudon

    2014-06-01

    Full Text Available Insect antennae are important mechanosensory and chemosensory organs. Insect appendages, such as antennae, are encased in a cuticular exoskeleton and are thought to bend only between segments or subsegments where the cuticle is thinner, more flexible, or bent into a fold. There is a growing appreciation of the dominating influence of folds in the mechanical behavior of a structure, and the bending of cricket antennae was considered in this context. Antennae will bend or deflect in response to forces, and the resulting bending behavior will affect the sensory input of the antennae. In some cricket antennae, such as in those of Acheta domesticus, there are a large number (>100 of subsegments (flagellomeres that vary in their length. We evaluated whether these antennae bend only at the joints between flagellomeres, which has always been assumed but not tested. In addition we questioned whether an antenna undergoes a length change as it bends, which would result from some patterns of joint deformation. Measurements using light microscopy and SEM were conducted on both male and female adult crickets (Acheta domesticus with bending in four different directions: dorsal, ventral, medial and lateral. Bending occurred only at the joints between flagellomeres, and antennae shortened a comparable amount during bending, regardless of sex or bending direction. The cuticular folds separating antennal flagellomeres are not very deep, and therefore as an antenna bends, the convex side (in tension does not have a lot of slack cuticle to unfold and does not lengthen during bending. Simultaneously on the other side of the antenna, on the concave side in compression, there is an increasing overlap in the folded cuticle of the joints during bending. Antennal shortening during bending would prevent stretching of antennal nerves and may promote hemolymph exchange between the antenna and head.

  12. Importance of Coulomb interactions in bound-to-continuum THz quantum cascade lasers

    Energy Technology Data Exchange (ETDEWEB)

    Jirauschek, C; Matyas, A [Emmy Noether Research Group ' Modeling of Quantum Cascade Devices' , Technische Universitaet Muenchen, D-80333 Munich (Germany); Lugli, P, E-mail: jirauschek@tum.d [Institute for Nanoelectronics, Technische Universitaet Muenchen, D-80333 Munich (Germany)

    2009-11-15

    We demonstrate the importance of Coulomb interactions in bound-to-continuum THz quantum cascade lasers, employing an ensemble Monte-Carlo analysis. In such structures, the electron-electron interactions between the closely spaced energy levels in the minibands tend to play a more important role than in resonant-phonon depopulation designs, where the energy levels are more energetically separated and LO phonon scattering prevails. Also a significant conduction band bending due to space charge effects is observed. Thus, especially for bound-to-continuum structures careful modelling of Coulomb interactions is crucial to obtain good agreement with experiment.

  13. Band-notched reconfigurable CPW-fed UWB antenna

    Science.gov (United States)

    Majid, H. A.; Rahim, M. K. A.; Hamid, M. R.; Murad, N. A.; Samsuri, N. A.; Yusof, M. F. M.; Kamarudin, M. R.

    2016-04-01

    A reconfigurable band-notched CPW-fed UWB antenna using electromagnetic bandgap (EBG) structure is proposed. Two structures are positioned adjacent to the transmission line of the UWB antenna. The band-notched characteristic can be disabled by switching the state of switch place at the strip line. The EBG structure produces reconfigurable band notched at 4.0 GHz, which covers C-band satellite communication (3.625-4.2 GHz) systems. The proposed antenna is suitable for UWB systems, which requires reconfigurable band reject function.

  14. A BRIGHT IMPULSIVE SOLAR BURST DETECTED AT 30 THz

    Energy Technology Data Exchange (ETDEWEB)

    Kaufmann, P.; Fernandes, L. O. T.; Kudaka, A. S.; De Souza, R. V.; Valio, A.; Raulin, J.-P. [Center of Radio Astronomy and Astrophysics, Engineering School, Mackenzie Presbyterian University, Sao Paulo, SP (Brazil); White, S. M. [Air Force Research Laboratories, Space Vehicles Directorate, Albuquerque, NM 87117 (United States); Freeland, S. L. [Lockheed Martin Solar and Astrophysics Laboratory, Palo Alto, CA 94304 (United States); Marcon, R. [' ' Gleb Wataghin' ' Physics Institute, State University of Campinas, Campinas, SP (Brazil); Aballay, J. L.; Fernandez, G.; Godoy, R.; Marun, A.; Gimenez de Castro, C. G. [El Leoncito Astronomical Complex, CONICET, San Juan (Argentina)

    2013-05-10

    Ground- and space-based observations of solar flares from radio wavelengths to gamma-rays have produced considerable insights but raised several unsolved controversies. The last unexplored wavelength frontier for solar flares is in the range of submillimeter and infrared wavelengths. Here we report the detection of an intense impulsive burst at 30 THz using a new imaging system. The 30 THz emission exhibited remarkable time coincidence with peaks observed at microwave, mm/submm, visible, EUV, and hard X-ray wavelengths. The emission location coincides with a very weak white-light feature, and is consistent with heating below the temperature minimum in the atmosphere. However, there are problems in attributing the heating to accelerated electrons. The peak 30 THz flux is several times larger than the usual microwave peak near 9 GHz, attributed to non-thermal electrons in the corona. The 30 THz emission could be consistent with an optically thick spectrum increasing from low to high frequencies. It might be part of the same spectral component found at sub-THz frequencies whose nature remains mysterious. Further observations at these wavelengths will provide a new window for flare studies.

  15. Hemispheric ultra-wideband antenna.

    Energy Technology Data Exchange (ETDEWEB)

    Brocato, Robert Wesley

    2006-04-01

    This report begins with a review of reduced size ultra-wideband (UWB) antennas and the peculiar problems that arise when building a UWB antenna. It then gives a description of a new type of UWB antenna that resolves these problems. This antenna, dubbed the hemispheric conical antenna, is similar to a conventional conical antenna in that it uses the same inverted conical conductor over a ground plane, but it also uses a hemispheric dielectric fill in between the conductive cone and the ground plane. The dielectric material creates a fundamentally new antenna which is reduced in size and much more rugged than a standard UWB conical antenna. The creation of finite-difference time domain (FDTD) software tools in spherical coordinates, as described in SAND2004-6577, enabled this technological advance.

  16. Dynamic Flaps Electronic Scan Antenna

    National Research Council Canada - National Science Library

    Gonzalez, Daniel

    2000-01-01

    A dynamic FLAPS(TM) electronic scan antenna was the focus of this research. The novelty S of this SBIR resides in the use of plasma as the main component of this dynamic X-Band phased S array antenna...

  17. Non-standard antennas

    CERN Document Server

    Le Chevalier, Francois; Staraj, Robert

    2013-01-01

    This book aims at describing the wide variety of new technologies and concepts of non-standard antenna systems - reconfigurable, integrated, terahertz, deformable, ultra-wideband, using metamaterials, or MEMS,  etc, and how they open the way to a wide range of applications, from personal security and communications to multifunction radars and towed sonars, or satellite navigation systems, with space-time diversity on transmit and receive. A reference book for designers  in this lively scientific community linking antenna experts and signal processing engineers.

  18. Antenna (Selected Articles),

    Science.gov (United States)

    1981-11-04

    random layout of the antenna (i.e. ’I=O). It is apparent from the figure that in the region of optimal N, the quantities AN and a2 change slowly. With a...introducing phase distribution of the field along the antenna equal to Z2W we can, in the limits of small angles in the region 0o O0 at distance R0 (focal...Shifrin, Ya. S. "Question of the Effect of Fluctuations on the Diffraction Image of a Focusing System," Trudy ARTA No. 46, 1960. 4. Tatarskiy, V. I. Teoria

  19. Printed MIMO antenna engineering

    CERN Document Server

    Sharawi, Mohammad S

    2014-01-01

    Wireless communications has made a huge leap during the past two decades. The multiple-input-multiple-output (MIMO) technology was proposed in the 1990's as a viable solution that can overcome the data rate limit experienced by single-input-single-output (SISO) systems. This resource is focused on printed MIMO antenna system design. Printed antennas are widely used in mobile and handheld terminals due to their conformity with the device, low cost, good integration within the device elements and mechanical parts, as well as ease of fabrication.A perfect design companion for practicing engineers

  20. DSN Microwave Antenna Holography

    Science.gov (United States)

    Rochblatt, D. J.; Seidel, B. L.

    1984-01-01

    The DSN microwave antenna holography project will obtain three-dimensional pictures of the large DSN antenna surfaces. These pictures must be of suffi icient resolution to allow adjustment of the reflector panels to an rms surface of 0.5 mm (0.25 mm, goal). The major parameters and equations needed to define a holographic measurement system are outlined and then the proof of concept demonstration measurement that was made at DSS-43 (Australia) that resulted in contour maps with spatial resolution of 7 m in the aperture plane and resolution orthogonal to the aperture plane of 0.7 mm was discussed.

  1. NATO Advanced Research Workshop on THz for CBRN and Explosives Detection and Diagnosis

    CERN Document Server

    Shulika, Oleksiy

    2017-01-01

    This work is intended to jointly address the development, realization and applications of emitters and detectors of terahertz (THz-0.3 THz up to 10 THz) and their application to diagnostics of CBRN effects and detection of explosives and CBRN. Hazardous substances typically exhibit rotational and vibrational transitions in this region, hence giving access to spectroscopic analysis of a large variety of molecules which play a key role in security as well as various other areas, e.g. air pollution, climate research, industrial process control, agriculture, food industry, workplace safety and medical diagnostics can be monitored by sensing and identifying them via THz (0.3 to 10 THz) and mid infrared (MIR-10 THz to 100 THz) absorption “finger prints”. Most plastics, textiles and paper are nearly transparent for THz radiation.

  2. Multiple-reflection conical microwave antenna

    Science.gov (United States)

    Oliver, R. E.

    1973-01-01

    Conical-Gregorian antenna concept, using conical reflector, promises excellent rf performance and offers potential advantages in areas of mechanical and structural design, surface measurement, and in furlability. Multiple reflection scheme between one or more subreflectors and main reflector is utilized. Subreflector can be reduced to as little as 0.1 the diameter of main reflector.

  3. Topology Optimization of Sub-Wavelength Antennas

    DEFF Research Database (Denmark)

    Erentok, Aycan; Sigmund, Ole

    2011-01-01

    We propose a topology optimization strategy for the systematic design of a three-dimensional (3D), conductor-based sub-wavelength antenna. The post-processed finite-element (FE) models of the optimized structure are shown to be self-resonant, efficient and exhibit distorted omnidirectional...

  4. Design and construction of CPW fed circular microstrip patch antennas

    Science.gov (United States)

    Vyas, Kirti; Singhal, P. K.; Sharma, A. K.; Pal, Manisha

    2013-01-01

    In this paper, we present feeding approaches of coplanar waveguide fed (CPW) circular microstrip patch antennas, with and without defected ground structure (DGS)`. The antenna feeding impedance is proposed as 50 ohms, built over FR4, a high dielectric constant substrate to obtain broad impedance bandwidth along with stability of the radiation patterns. The antenna with defected ground structure is designed to have band-notched characteristics at 3.5 GHz (for Wi-MAX band-3.3 to 3.7 GHz), at 8.2 GHz (for ITU band-8.025 GHz to 8.4 GHz) so as to avoid interference from these. The FR4 is used as dielectric with value of dielectric loss tangent constant as 0.002 and relative permittivity with 4.4. After applying DGS in ground of the proposed antenna there were improvements concerning bandwidth, and also a small increase in gain was noticed. These antennas are of small sizes with dimensions; 30 mm X 43 mm X 1.6 mm, cheap, compact and easy to fabricate, and achieve good radiation characteristics with higher return loss. This first antenna can have wide application in a great variety of wireless communication and second can operate well as UWB antenna with band notched characteristics. The performance of two antennas is compared in respect to gain, VSWR, return loss and impedance matching.

  5. Terahertz antenna technology for space applications

    CERN Document Server

    Choudhury, Balamati; Jha, Rakesh Mohan

    2016-01-01

    This book explores the terahertz antenna technology towards implementation of compact, consistent and cheap terahertz sources, as well as the high sensitivity terahertz detectors. The terahertz EM band provides a transition between the electronic and the photonic regions thus adopting important characteristics from these regimes. These characteristics, along with the progress in semiconductor technology, have enabled researchers to exploit hitherto unexplored domains including satellite communication, bio-medical imaging, and security systems. The advances in new materials and nanostructures such as graphene will be helpful in miniaturization of antenna technology while simultaneously maintaining the desired output levels. Terahertz antenna characterization of bandwidth, impedance, polarization, etc. has not yet been methodically structured and it continues to be a major research challenge. This book addresses these issues besides including the advances of terahertz technology in space applications worldwide,...

  6. Dual Polarized Monopole Patch Antennas for UWB Applications with Elimination of WLAN Signals

    Directory of Open Access Journals (Sweden)

    P. Kumar

    2016-05-01

    Full Text Available This paper presents the design, fabrication and measurement of dual polarized microstrip patch antennas for ultra wideband (UWB applications with notch at 5-6 GHz band. The proposed antenna rejects the wireless local area network (WLAN signals and work properly in the entire remaining ultra-wideband. Two antennas are designed for two different frequency bands of ultra wideband and both antennas together produce the entire ultra wideband with notch at 5-6 GHz band. The antennas are fed by a 50 coaxial probe and the entire design is optimized using CST Microwave Studio. The bandwidth of 3.1-5 GHz is achieved by the optimized design of Antenna-1 and the bandwidth of 6 -10.6 GHz is achieved by the optimized design of Antenna-2. The bandwidth of the optimized combined antenna is 3.1-10.6 GHz with elimination of the 5-6 GHz band. Both antennas are simulated, developed and measured. The simulated and measured results are presented. The two designed dual polarized antennas i.e. Antenna-1 and Antenna-2 can be used for 3.1-5 GHz band and 6-10.6 GHz band dual polarized applications, respectively, and the combined antenna structure can be used for UWB dual polarized applications with elimination of 5-6 GHz band signals.

  7. Towards a THz Backward Wave Amplifier in European FP7 OPTHER Project

    DEFF Research Database (Denmark)

    Dispenza, Massimiliano; Cojocaru, C.-S.; De Rossi, Alfredo

    2010-01-01

    Within the EC funded international project OPTHER (OPtically Driven TeraHertz AmplifiERs) a considerable technological effort is being undertaken, in terms of technological development, THz device design and integration. The ultimate goal is to develop a miniaturised THz amplifier based on vacuum...... with a proper device configuration and careful optimization of the different parts of the amplifier. Two parallel schemes will be employed for amplifier realisation: THz Drive Signal Amplifier and Optically Modulated Beam THz Amplifier....

  8. Mode profiling of THz fibers with dynamic aperture near-field imaging

    DEFF Research Database (Denmark)

    Stecher, Matthias; Dürrschmidt, Stefan F.; Nielsen, Kristian

    2011-01-01

    We present terahertz near-field mode profiling of different polymer THz fibers. Images with a resolution below the THz wavelength show the fundamental mode profile and higher order modes appearing at higher frequencies.......We present terahertz near-field mode profiling of different polymer THz fibers. Images with a resolution below the THz wavelength show the fundamental mode profile and higher order modes appearing at higher frequencies....

  9. Design and investigation of sectoral circular disc monopole fractal antenna and its backscattering

    Directory of Open Access Journals (Sweden)

    Raj Kumar

    2017-02-01

    Full Text Available This article presents the design of sectoral circular disc fractal antenna. The proposed antenna has been excited using CPW – feed. The measured result of this antenna offers the ultra wideband characteristics from 3.265 GHz to 15.0 GHz. The measured and simulated results are compared and found in good agreement. The impedance match of the antenna throughout the band is improved by incorporating the rectangular slots in the ground plane. The measured radiation patterns of this antenna are nearly omni-directional in H-plane and bidirectional in E-plane. The backscattering of antenna is also discussed and calculated for antenna mode and structural mode scattering. This type of antenna is useful for UWB system, microwave imaging and vehicular radar, precision positioning location.

  10. Reduced-volume antennas with integrated high-impedance electromagnetic surfaces.

    Energy Technology Data Exchange (ETDEWEB)

    Forman, Michael A.

    2006-11-01

    Several antennas with integrated high-impedance surfaces are presented. The high-impedance surface is implemented as a composite right/left-handed (CRLH) metamaterial fabricated from a periodic structure characterized by a substrate, filled with an array of vertical vias and capped by capacitive patches. Omnidirectional antennas placed in close proximity to the high-impedance surface radiate hemispherically with an increase in boresight far-field pattern gain of up to 10 dB and a front-to-back ratio as high as 13 dB at 2.45 GHz. Several TEM rectangular horn antennas are realized by replacing conductor walls with high-impedance surfaces. The TEM horn antennas are capable of operating below the TE{sub 1,0} cutoff frequency of a standard all-metal horn antenna, enabling a reduction in antenna volume. Above the cutoff frequency the TEM horn antennas function similarly to standard rectangular horn antennas.

  11. Experimental measurements of the ion cyclotron antennas' coupling and rf characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, D.J.; Baity, F.W.; Becraft, W.R.; Caughman, J.B.O.; Owens, T.L.

    1985-01-01

    The rf coupling capabilities and characteristics of various antennas have been measured. The tested antenna configurations include the simple loop antenna operated at resonant lengths as used on Alcator-C, the cavity antenna proposed for Doublet III-D and the resonant double loop, asymmetric resonant double loop, and U-slot antennas. Models of the voltage, magnetic fields outside the structure, and current have been correlated with the measurements made on these antennas. From these measurements and from typical observations of ICRH coupling in tokamaks, we are studying power and frequency limitations on each antenna and the causes of the limitations. A comparison of the technology, performance, and power limitations of each type of antenna is presented.

  12. Design and verification of monopole patch antenna systems to generate orbital angular momentum waves

    Directory of Open Access Journals (Sweden)

    Dandan Liu

    2017-09-01

    Full Text Available Monopole patch antenna systems, which can generate orbital angular momentum (OAM waves at 2.4GHz, are proposed in this paper. The proposed antenna systems have advantages of simple planar structure and small size of antenna element. Design, simulation, fabrication and measurement of the proposed antenna systems are presented. Two feeding networks, which constitute the proposed antenna systems with monopole patch antenna array, are designed to generate modes 1 and 2 of OAM waves. The antenna systems for both modes are shown to be effective in generating OAM waves of modes 1 and 2 from both simulation and three types of measurement: radiation pattern, phase distribution and phase gradient. Simulation and measurement results of radiation pattern and phase distribution have shown very close results. Phase gradient measurement results has verified that the generated waves from the antenna systems are indeed OAM waves.

  13. Design and verification of monopole patch antenna systems to generate orbital angular momentum waves

    Science.gov (United States)

    Liu, Dandan; Gui, Liangqi; Zhou, Cong; Zhang, Zixiao; Chen, Han; Jiang, Tao

    2017-09-01

    Monopole patch antenna systems, which can generate orbital angular momentum (OAM) waves at 2.4GHz, are proposed in this paper. The proposed antenna systems have advantages of simple planar structure and small size of antenna element. Design, simulation, fabrication and measurement of the proposed antenna systems are presented. Two feeding networks, which constitute the proposed antenna systems with monopole patch antenna array, are designed to generate modes 1 and 2 of OAM waves. The antenna systems for both modes are shown to be effective in generating OAM waves of modes 1 and 2 from both simulation and three types of measurement: radiation pattern, phase distribution and phase gradient. Simulation and measurement results of radiation pattern and phase distribution have shown very close results. Phase gradient measurement results has verified that the generated waves from the antenna systems are indeed OAM waves.

  14. Precise Orbit Determination for LEO Spacecraft Using GNSS Tracking Data from Multiple Antennas

    Science.gov (United States)

    Kuang, Da; Bertiger, William; Desai, Shailen; Haines, Bruce

    2010-01-01

    To support various applications, certain Earth-orbiting spacecrafts (e.g., SRTM, COSMIC) use multiple GNSS antennas to provide tracking data for precise orbit determination (POD). POD using GNSS tracking data from multiple antennas poses some special technical issues compared to the typical single-antenna approach. In this paper, we investigate some of these issues using both real and simulated data. Recommendations are provided for POD with multiple GNSS antennas and for antenna configuration design. The observability of satellite position with multiple antennas data is compared against single antenna case. The impact of differential clock (line biases) and line-of-sight (up, along-track, and cross-track) on kinematic and reduced-dynamic POD is evaluated. The accuracy of monitoring the stability of the spacecraft structure by simultaneously performing POD of the spacecraft and relative positioning of the multiple antennas is also investigated.

  15. 3D THz hyperspectrum applied in security check-in

    Science.gov (United States)

    Damian, V.; Logofǎtu, P. C.; Vasile, T.

    2016-12-01

    We developed a measuring technology using a TDS-THz system to construct hyperspectral images of some objects, including hazardous materials. "T-rays" (the THz spectral domain of the light) have a growing importance in security and imagistic domain. Due to their property of penetrating through dielectric objects, and using non-ionizing radiations, the THz systems have become a standard for "hot-places" (airports, train stations etc.). The hyperspectral images are 3D images having 2D spatial dimension and one spectral dimension. In this way, we obtain simultaneously information about the form of the object and its molecular composition. For discriminating between substances, we must first build a database of spectra for hazardous and dangerous substances. We experiment our system on some items (among them a firecracker, a cigarette and a metal collar) and we tried to discriminate between them using the database of spectra.

  16. Enhanced THz guiding properties of curved two-wire lines.

    Science.gov (United States)

    Zha, Jingshu; Kim, Geun Ju; Jeon, Tae-In

    2016-03-21

    We present experimental and simulation studies of enhanced terahertz (THz) guiding properties of curved two-wire lines for several surface conditions. When a THz-wave propagates through curved two-wire lines, a rough wire surface with dielectric coating contributes to a lower bending loss compared to a smooth or rough wire surface without coating. Dielectric coating and rough surface confine the THz field to the wire surface making the bending loss low. The guiding property at a curve depth of 30 mm of a rough wire surface with 25-μm-thick coating is improved by 34% compared to that of a smooth wire without coating. Furthermore, computer simulation technology (CST) software visually shows the bending loss as same as the experimental studies.

  17. Method for the production of wideband THz radiation

    Science.gov (United States)

    Krafft, Geoffrey A [Newport News, VA

    2008-01-01

    A method for the production of extremely wide bandwidth THz radiation comprising: delivering an electron beam from a source to an undulator that does not deflect the angle or transversely move the electron beam; and optimizing the undulator to yield peak emission in the middle of the THz band (1 THz). These objectives are accomplished by magnetically bending the orbit of the incoming electron beam in the undulator according to the function x(z)=x.sub.o exp(-z.sup.2/2.sigma..sup.2) and controlling the transverse magnetic field to be B(z)=B.sub.0(1-z.sup.2/.sigma..sup.2)exp(-z.sup.2/2.sigma..sup.2).

  18. High peak power THz source for ultrafast electron diffraction

    Directory of Open Access Journals (Sweden)

    Shengguang Liu

    2018-01-01

    Full Text Available Terahertz (THz science and technology have already become the research highlight at present. In this paper, we put forward a device setup to carry out ultrafast fundamental research. A photocathode RF gun generates electron bunches with ∼MeV energy, ∼ps bunch width and about 25pC charge. The electron bunches inject the designed wiggler, the coherent radiation at THz spectrum emits from these bunches and increases rapidly until the saturation at ∼MW within a short wiggler. THz pulses can be used as pump to stimulate an ultra-short excitation in some kind of sample. Those electron bunches out of wiggler can be handled into bunches with ∼1pC change, small beam spot and energy spread to be probe. Because the pump and probe comes from the same electron source, synchronization between pump and probe is inherent. The whole facility can be compacted on a tabletop.

  19. High peak power THz source for ultrafast electron diffraction

    Science.gov (United States)

    Liu, Shengguang

    2018-01-01

    Terahertz (THz) science and technology have already become the research highlight at present. In this paper, we put forward a device setup to carry out ultrafast fundamental research. A photocathode RF gun generates electron bunches with ˜MeV energy, ˜ps bunch width and about 25pC charge. The electron bunches inject the designed wiggler, the coherent radiation at THz spectrum emits from these bunches and increases rapidly until the saturation at ˜MW within a short wiggler. THz pulses can be used as pump to stimulate an ultra-short excitation in some kind of sample. Those electron bunches out of wiggler can be handled into bunches with ˜1pC change, small beam spot and energy spread to be probe. Because the pump and probe comes from the same electron source, synchronization between pump and probe is inherent. The whole facility can be compacted on a tabletop.

  20. Radiation characteristics of input power from surface wave sustained plasma antenna

    International Nuclear Information System (INIS)

    Naito, T.; Yamaura, S.; Fukuma, Y.; Sakai, O.

    2016-01-01

    This paper reports radiation characteristics of input power from a surface wave sustained plasma antenna investigated theoretically and experimentally, especially focusing on the power consumption balance between the plasma generation and the radiation. The plasma antenna is a dielectric tube filled with argon and small amount of mercury, and the structure is a basic quarter wavelength monopole antenna at 2.45 GHz. Microwave power at 2.45 GHz is supplied to the plasma antenna. The input power is partially consumed to sustain the plasma, and the remaining part is radiated as a signal. The relationship between the antenna gain and the input power is obtained by an analytical derivation and numerical simulations. As a result, the antenna gain is kept at low values, and most of the input power is consumed to increase the plasma volume until the tube is filled with the plasma whose electron density is higher than the critical electron density required for sustaining the surface wave. On the other hand, the input power is consumed to increase the electron density after the tube is fully filled with the plasma, and the antenna gain increases with increasing the electron density. The dependence of the antenna gain on the electron density is the same as that of a plasma antenna sustained by a DC glow discharge. These results are confirmed by experimental results of the antenna gain and radiation patterns. The antenna gain of the plasma is a few dB smaller than that of the identical metal antenna. The antenna gain of the plasma antenna is sufficient for the wireless communication, although it is difficult to substitute the plasma antenna for metal antennas completely. The plasma antenna is suitable for applications having high affinity with the plasma characteristics such as low interference and dynamic controllability.

  1. Validation of Emulated Omnidirectional Antenna Output Using Directive Antenna Data

    DEFF Research Database (Denmark)

    Hejselbæk, Johannes; Karstensen, Anders; Nielsen, Jesper Ødum

    2017-01-01

    In this paper, we present validation of a method for constructing a virtual omnidirectional antenna in the azimuth plane. The virtual omnidirectional antenna utilizes a combination of data from directive horn antennas. The aim is to utilize the high gain of the horn antenna to improve the dynamic...... range of channel sounding measurements conducted in the centimeter and millimeter wave bands. The resulting complex impulse response from the virtual omnidirectional antenna is used to find the power-delay-profile (PDP). This is then compared to measurements conducted at the same time using a real...... omnidirectional antenna. The validation shows that the synthesized omnidirectional is capable of predicting main components and the slope of the PDP. Further, it is shown that by choosing angular sampling steps corresponding to the half power beam width (HPBW) of the used antenna similar power levels can...

  2. Wireless Distributed Antenna MIMO

    DEFF Research Database (Denmark)

    2015-01-01

    The present disclosure relates to system applications of multicore optical fibers. One embodiment relates to a base transceiver station for a wireless telecommunication system comprising a plurality of antenna units arranged in a MIMO configuration and adapted for transmission and/or reception...

  3. MEMS Tunable Antennas

    DEFF Research Database (Denmark)

    Barrio, Samantha Caporal Del; Morris, Art; Pedersen, Gert Frølund

    2014-01-01

    Addressing low frequency bands is challenging on small platforms. Tunability is a promising solution to cover the bandwidth required for 4G mobile communication. The work presents two designs and shows that for comparable efficiency and bandwidth, the tunable antenna occupies half the volume requ...

  4. Community Antenna Television (CATV).

    Science.gov (United States)

    Federal Communications Commission, Washington, DC.

    The number of households hooked up to cable television or community antenna television (CATV) is expanding rapidly, and Federal Communications Commission (FCC) has been developing regulations since 1962 to guide the growth of the industry. By 1965 the FCC had claimed jurisdiction over all CATV systems in the U. S. This jurisdiction was challenged…

  5. Measurement of LHCD antenna position in Aditya tokamak

    International Nuclear Information System (INIS)

    Ambulkar, K K; Sharma, P K; Virani, C G; Parmar, P R; Thakur, A L; Kulkarni, S V

    2010-01-01

    To drive plasma current non-inductively in ADITYA tokamak, 120 kW pulsed Lower Hybrid Current Drive (LHCD) system at 3.7 GHz has been designed, fabricated and installed on ADITYA tokamak. In this system, the antenna consists of a grill structure, having two rows, each row comprising of four sub-waveguides. The coupling of LHCD power to the plasma strongly depends on the plasma density near the mouth of grill antenna. Thus the grill antenna has to be precisely positioned for efficient coupling. The movement of mechanical bellow, which contracts or expands up to 50mm, governs the movement of antenna. In order to monitor the position of the antenna precisely, the reference position of the antenna with respect to the machine/plasma position has to be accurately determined. Further a mechanical system or an electronic system to measure the relative movement of the antenna with respect to the reference position is also desired. Also due to poor accessibility inside the ADITYA machine, it is impossible to measure physically the reference position of the grill antenna with respect to machine wall, taken as reference position and hence an alternative method has to be adopted to establish these measurements reliably. In this paper we report the design and development of a mechanism, using which the antenna position measurements are made. It also describes a unique method employing which the measurements of the reference position of the antenna with respect to the inner edge of the tokamak wall is carried out, which otherwise was impossible due to poor accessibility and physical constraints. The position of the antenna is monitored using an electronic scale, which is developed and installed on the bellow. Once the reference position is derived, the linear potentiometer, attached to the bellow, measures the linear distance using position transmitter. The accuracy of measurement obtained in our setup is within +/- 0.5 % and the linearity, along with repeatability is excellent.

  6. Developing novel 3D antennas using advanced additive manufacturing technology

    Science.gov (United States)

    Mirzaee, Milad

    In today's world of wireless communication systems, antenna engineering is rapidly advancing as the wireless services continue to expand in support of emerging commercial applications. Antennas play a key role in the performance of advanced transceiver systems where they serve to convert electric power to electromagnetic waves and vice versa. Researchers have held significant interest in developing this crucial component for wireless communication systems by employing a variety of design techniques. In the past few years, demands for electrically small antennas continues to increase, particularly among portable and mobile wireless devices, medical electronics and aerospace systems. This trend toward smaller electronic devices makes the three dimensional (3D) antennas very appealing, since they can be designed in a way to use every available space inside the devise. Additive Manufacturing (AM) method could help to find great solutions for the antennas design for next generation of wireless communication systems. In this thesis, the design and fabrication of 3D printed antennas using AM technology is studied. To demonstrate this application of AM, different types of antennas structures have been designed and fabricated using various manufacturing processes. This thesis studies, for the first time, embedded conductive 3D printed antennas using PolyLactic Acid (PLA) and Acrylonitrile Butadiene Styrene (ABS) for substrate parts and high temperature carbon paste for conductive parts which can be a good candidate to overcome the limitations of direct printing on 3D surfaces that is the most popular method to fabricate conductive parts of the antennas. This thesis also studies, for the first time, the fabrication of antennas with 3D printed conductive parts which can contribute to the new generation of 3D printed antennas.

  7. Development of nondestructive inspection tools for cultural heritage artefacts with 3D THz imaging

    DEFF Research Database (Denmark)

    Dandolo, Corinna Ludovica Koch

    The ability of terahertz time-domain imaging (THz-TDI) to visualize surface and subsurface features of artworks has recently been established. A limitation in imaging subsurface features by THz-TDI in reflection mode is the difficulty to handle THz signal separation when the surface of the layer ...

  8. Electric field, Magnetic field and Magnetization : THz time-domain spectroscopy studies

    NARCIS (Netherlands)

    Kumar, N.

    2015-01-01

    Terahertz radiation is electromagnetic waves with frequencies from 0.1-10 THz. THz radiation can pass through cardboard, paper, plastics, ceramics and many other materials. Hence, it can be used for non-destructive imaging. Another important application of THz radiation is spectroscopy. Many organic

  9. THz photonic wireless links with 16-QAM modulation in the 375-450 GHz band

    DEFF Research Database (Denmark)

    Jia, Shi; Yu, Xianbin; Hu, Hao

    2016-01-01

    We propose and experimentally demonstrate THz photonic wireless communication systems with 16-QAM modulation in the 375-450 GHz band. The overall throughput reaches as high as 80 Gbit/s by exploiting four THz channels with 5 Gbaud 16-QAM baseband modulation per channel. We create a coherent optic...... signal transmitter and the THz wireless transmitter with negligible induced power penalty....

  10. Optical rectification through an Al 2 O 3 based MIM passive rectenna at 28.3 THz

    KAUST Repository

    Jayaswal, Gaurav

    2017-11-21

    Harevesting energy from waste heat which fluctuates between, approximately, 250 K and 1500 K, i.e., peaking at 2–11 μm, could be a game changer in terms of tapping on to renewable energy sources. However, research in this area has remained elusive due to numerous challenges. We consider waste heat to be an electromagnetic (EM) wave in the mid infrared (IR) frequency range, which can be captured through a resonant antenna and rectified into useful DC through a diode, an arrangement typically known as a rectenna. A bowtie antenna has been optimized for IR field capture and enhancement through EM simulations. At the overlap of the bowtie arms, a metal-insulator-metal (MIM) diode has been realized that can operate at such a high frequency (28.3 THz or 10.6 μm). The choice of a low permittivity insulator (Al2O3) helps metigate the RC time constant and the diode\\'s cutoff frequency, whereas the two different work function metals, Au and Ti, facilitate diode operation through tunneling at no applied bias. A custom optical characterization setup employing a 10.6 μm CO2 laser has been used to assess the IR capture and rectification ability of the rectenna device. A polarization dependent voltage output which is well above the noise level and well matched with our calculations, confirms the successful rectenna operation. According to authors\\' best knowledge, this is the first demonstration of rectification at 28.3 THz through a MIM diode based rectenna at zero applied bias.

  11. Structural and electrical characterization of diamond films deposited in nitrogen/oxygen containing gas mixture by linear antenna microwave CVD process

    Czech Academy of Sciences Publication Activity Database

    Vojs, Marian; Varga, Marián; Babchenko, Oleg; Ižák, Tibor; Mikolášek, M.; Marton, M.; Kromka, Alexander

    2014-01-01

    Roč. 312, SEP (2014), s. 226-230 ISSN 0169-4332 R&D Projects: GA ČR(CZ) GBP108/12/G108 Institutional support: RVO:68378271 Keywords : pulsed linear antenna microwave chemical vapor deposition * nanocrystalline diamond * Raman spectroscopy * admittance spectroscopy * n-type conductive NCD Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.711, year: 2014

  12. THz-TDS Signal Analysis and Substance Identification

    International Nuclear Information System (INIS)

    Xie Weixin; Li Jing; Pei Jihong

    2011-01-01

    The terahertz time-domain spectroscopy (THz-TDS) imaging system can obtain high-dimensional signals of the substance fingerprint information. It is necessary to process properly to use some signal processing techniques especially for high dimensional signals. As a mathematical description language, geometric algebra (GA) provides not only a powerful algebraic framework for the multi-dimensional vector analysis and computing, but also a unified measurement and geometrical description for different geometric models. On the basis of the GA theories, a new signal analysis method of the THz-TDS is presented. Based on the characteristics of THz-TDS signals, signals are mapped into vectors in the high-dimensional real vector space. The vectors are represented with hyper-complex numbers. We can analyze the vectors using theories of GA. Based on the physical mechanism of the THz-TDS signal analysis, geometric distribution properties and algebraic relationships of THz-TDS signals are deduced. It is demonstrated that every complex refractive index of the sample relates to a unique 2-blade B 2 , all vectors corresponding to the samples of the same substance are collinear and belong to the intrinsic 2-blade of the substance. In projective interpretation, the 2-blade B 2 represents a fixed line and all vectors related to the same substance are along that line. Accordingly, a novel substance identification method based on the relative THz-TDS is presented. In the method, two THz-TDS signals through the samples of the same substance but different thickness are measured. The intrinsic 2-blade B 2 of the substance is then determined by the outer product of these two corresponding vectors. Using the conformal split by the fixed bivector B 2 , each vector corresponding to THz-TDS signals in the vector space V n can be linearly splitted into vectors in vector spaces V 2 and V n-2 . Since that 2-dimensional subspace V 2 is the support of B 2 , the subspace is also a label for substances

  13. Very high power THz radiation at Jefferson Lab

    International Nuclear Information System (INIS)

    We report the production of high power (20 W average, ∼1 MW peak) broadband THz light based on coherent emission from relativistic electrons. We describe the source, presenting theoretical calculations and their experimental verification. For clarity we compare this source with that based on ultrafast laser techniques, and in fact the radiation has qualities closely analogous to those produced by such sources, namely that it is spatially coherent, and comprises short duration pulses with transform-limited spectral content. In contrast to conventional THz radiation, however, the intensity is many orders of magnitude greater due to the relativistic enhancement

  14. Design of Multi-Order Diffractive THz Lenses

    Science.gov (United States)

    2012-09-23

    surface. This makes the fabrication process easier and more accurate, thereby improving optical quality. A CNC lathe can be used to carve the lens out...for low-end THz operation (200-800 GHz). The lens was fabricated in Teflon with a small CNC lathe and can be seen in Fig. 3. With only 4 zones...excellent THz transparency and is readily available. Once the CNC turning was complete, the lens was separated from its substrate with a band-saw and

  15. Very high power THz radiation at Jefferson Lab

    International Nuclear Information System (INIS)

    Carr, G.L.; Martin, Michael C.; McKinney, Wayne R.; Jordan, K.; Neil, George R.; Williams, G.P.

    2002-01-01

    We report the production of high power (20 watts average, ∼;1 Megawatt peak) broadband THz light based on coherent emission from relativistic electrons. We describe the source, presenting theoretical calculations and their experimental verification. For clarity we compare this source with one based on ultrafast laser techniques, and in fact the radiation has qualities closely analogous to that produced by such sources, namely that it is spatially coherent, and comprises short duration pulses with transform-limited spectral content. In contrast to conventional THz radiation, however, the intensity is many orders of magnitude greater due to the relativistic enhancement

  16. Detection of the THz waves from the 5m distance

    Science.gov (United States)

    Walczakowski, Michal; Palka, Norbert; Szustakowski, Mieczyslaw; Czerwinski, Adam; Sypek, Maciej

    2013-10-01

    We report on technical aspects connected with detection of the terahertz (THz) waves reflected from a small target which is situated at the distance of 5 meters. Details of experimental setup are presented. An optical parametric oscillator (OPO) was used as a THz nanosecond pulses radiation source and a hot-electron bolometer (HEB) was applied for pulse detection. A method of spectrum calculation from experimental data is described. Measured reflectance spectra of few materials are presented with explanation of the origin of water vapor hole burning in the reflectance spectrum.

  17. THz detectors using surface Josephson plasma waves in layered superconductors

    International Nuclear Information System (INIS)

    Savel'ev, Sergey; Yampol'skii, Valery; Nori, Franco

    2006-01-01

    We describe a proposal for THz detectors based on the excitation of surface waves, in layered superconductors, at frequencies lower than the Josephson plasma frequency ω J . These waves propagate along the vacuum-superconductor interface and are attenuated in both transverse directions out of the surface (i.e., towards the superconductor and towards the vacuum). The surface Josephson plasma waves are also important for the complete suppression of the specular reflection from a sample (Wood's anomalies, used for gratings) and produce a huge enhancement of the wave absorption, which can be used for the detection of THz waves

  18. Fiber-Drawn Metamaterial for THz Waveguiding and Imaging

    DEFF Research Database (Denmark)

    Atakaramians, Shaghik; Stefani, Alessio; Li, Haisu

    2017-01-01

    and sub-diffraction imaging. We show the experimental demonstration of THz radiation guidance through hollow core waveguides with metamaterial cladding, where substantial improvements were realized compared to conventional hollow core waveguides, such as reduction of size, greater flexibility, increased...... single-mode operating regime, and guiding due to magnetic and electric resonances. We also report recent and new experimental work on near- and far-field THz imaging using wire array metamaterials that are capable of resolving features as small as λ/28....

  19. Electromagnetic reciprocity in antenna theory

    CERN Document Server

    Stumpf, Martin

    2018-01-01

    The reciprocity theorem is among the most intriguing concepts in wave field theory and has become an integral part of almost all standard textbooks on electromagnetic (EM) theory. This book makes use of the theorem to quantitatively describe EM interactions concerning general multiport antenna systems. It covers a general reciprocity-based description of antenna systems, their EM scattering properties, and further related aspects. Beginning with an introduction to the subject, Electromagnetic Reciprocity in Antenna Theory provides readers first with the basic prerequisites before offering coverage of the equivalent multiport circuit antenna representations, EM coupling between multiport antenna systems and their EM interactions with scatterers, accompanied with the corresponding EM compensation theorems.

  20. Quartz antenna with hollow conductor

    Science.gov (United States)

    Leung, Ka-Ngo; Benabou, Elie

    2002-01-01

    A radio frequency (RF) antenna for plasma ion sources is formed of a hollow metal conductor tube disposed within a glass tube. The hollow metal tubular conductor has an internal flow channel so that there will be no coolant leakage if the outer glass tube of the antenna breaks. A portion of the RF antenna is formed into a coil; the antenna is used for inductively coupling RF power to a plasma in an ion source chamber. The antenna is made by first inserting the metal tube inside the glass tube, and then forming the glass/metal composite tube into the desired coil shape.

  1. Antenna theory analysis and design

    CERN Document Server

    Balanis, Constantine A

    2005-01-01

    The discipline of antenna theory has experienced vast technological changes. In response, Constantine Balanis has updated his classic text, Antenna Theory, offering the most recent look at all the necessary topics. New material includes smart antennas and fractal antennas, along with the latest applications in wireless communications. Multimedia material on an accompanying CD presents PowerPoint viewgraphs of lecture notes, interactive review questions, Java animations and applets, and MATLAB features. Like the previous editions, Antenna Theory, Third Edition meets the needs of e

  2. Design, Fabrication, and Testing of Active Skin Antenna with 3D Printing Array Framework

    Directory of Open Access Journals (Sweden)

    Jinzhu Zhou

    2017-01-01

    Full Text Available An active skin antenna with structural load-bearing and electromagnetic functions is usually installed in the structural surface of mobile vehicles such as aircrafts, warships, and high-speed train. This paper presents the design, fabrication, and testing of a novel active skin antenna which consists of an encapsulation shell, antenna skin, and RF and beam control circuits. The antenna skin which consists of the facesheet, honeycomb, array framework, and microstrip antenna elements was designed by using Bayesian optimization, in order to improve the design efficiency. An active skin antenna prototype with 32 microstrip antenna elements was fabricated by using a hybrid manufacturing method. In this method, 3D printing technology was applied to fabricate the array framework, and the different layers were bonded to form the final antenna skin by using traditional composite process. Some experimental testing was conducted, and the testing results validate the feasibility the proposed antenna skin structure. The proposed design and fabrication technique is suitable for the development of conformal load-bearing antenna or smart skin antenna installed in the structural surface of aircraft, warships, and armored vehicles.

  3. AASERT: Hydrodynamic Interaction Between Olfactory Antennae and Odor Plumes

    National Research Council Canada - National Science Library

    Koehl, M

    2002-01-01

    We trained graduate and undergraduate students by involving them in research elucidating ways in which the structure and the motions of olfactory antennae affect how they encounter the concentration...

  4. Improvement of Electromagnetic Code for Phased Array Antenna Design

    National Research Council Canada - National Science Library

    Holter, Henrik

    2007-01-01

    ... . An existing time domain code for electromagnetic design and analysis of phased array antennas and other periodic structures such as frequency selective surfaces and meta-materials has been improved in several ways...

  5. Foamed Antenna Support for Very Large Apertures, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed Phase I program will demonstrate the feasibility of the in-space production of large aperture antenna structures. The use of a novel open cell foam,...

  6. Unsupervised image segmentation for passive THz broadband images for concealed weapon detection

    Science.gov (United States)

    Ramírez, Mabel D.; Dietlein, Charles R.; Grossman, Erich; Popović, Zoya

    2007-04-01

    This work presents the application of a basic unsupervised classification algorithm for the segmentation of indoor passive Terahertz images. The 30,000 pixel broadband images of a person with concealed weapons under clothing are taken at a range of 0.8-2m over a frequency range of 0.1-1.2THz using single-pixel row-based raster scanning. The spiral-antenna coupled 36x1x0.02μm Nb bridge cryogenic micro-bolometers are developed at NIST-Optoelectronics Division. The antenna is evaporated on a 250μm thick Si substrate with a 4mm diameter hyper-hemispherical Si lens. The NETD of the microbolometer is 125mK at an integration time of 30 ms. The background temperature calibration is performed with a known 25 pixel source above 330 K, and a measured background fluctuation of 200-500mK. Several weapons were concealed under different fabrics: cotton, polyester, windblocker jacket and thermal sweater. Measured temperature contrasts ranged from 0.5-1K for wrinkles in clothing to 5K for a zipper and 8K for the concealed weapon. In order to automate feature detection in the images, some image processing and pattern recognition techniques have been applied and the results are presented here. We show that even simple algorithms, that can potentially be performed in real time, are capable of differentiating between a metal and a dielectric object concealed under clothing. Additionally, we show that pre-processing can reveal low temperature contrast features, such as folds in clothing.

  7. Simulation of electron transport in GaAs/AlAs superlattices with a small number of periods for the THz frequency range

    Energy Technology Data Exchange (ETDEWEB)

    Pavelyev, D. G., E-mail: pavelev@rf.unn.ru, E-mail: obolensk@rf.unn.ru [Lobachevsky State University of Nizhny Novgorod (Russian Federation); Vasilev, A. P., E-mail: vasiljev@mail.ioffe.ru [Russian Academy of Sciences, Submicron Heterostructures for Microelectronics, Research and Engineering Center (Russian Federation); Kozlov, V. A., E-mail: kozlov@ipm.sci-nnov.ru; Koschurinov, Yu. I.; Obolenskaya, E. S.; Obolensky, S. V. [Lobachevsky State University of Nizhny Novgorod (Russian Federation); Ustinov, V. M., E-mail: vmust@beam.ioffe.ru [Russian Academy of Sciences, Ioffe Physical–Technical Institute (Russian Federation)

    2016-11-15

    The electron transport in superlattices based on GaAs/AlAs heterostructures with a small number of periods (6 periods) is calculated by the Monte Carlo method. These superlattices are used in terahertz diodes for the frequency stabilization of quantum cascade lasers in the range up to 4.7 THz. The band structure of superlattices with different numbers of AlAs monolayers is considered and their current–voltage characteristics are calculated. The calculated current–voltage characteristics are compared with the experimental data. The possibility of the efficient application of these superlattices in the THz frequency range is established both theoretically and experimentally.

  8. Study of blood plasma optical properties in mice grafted with Ehrlich carcinoma in the frequency range 0.1–1.0 THz

    Science.gov (United States)

    Smolyanskaya, O. A.; Kravtsenyuk, O. V.; Panchenko, A. V.; Odlyanitskiy, E. L.; Guillet, J. P.; Cherkasova, O. P.; Khodzitsky, M. K.

    2017-12-01

    In the course of in vitro studies of blood of laboratory animals with progressing Ehrlich carcinoma, we have revealed the change of the blood plasma optical properties in the THz range, which can be used for developing the express diagnostics of the presence of oncological diseases. An applied software package is elaborated that allows the phantoms of biological samples having a complex structure to be numerically simulated and the parameters of the electromagnetic wave reflected from these samples in the THz frequency range to be calculated. Presented at the Fundamentals of Laser Micro- and Nanotechnologies (FLAMN-16) International Symposium (Pushkin, Leningrad oblast, 27 June to 1 July 2016).

  9. Non-radially polarized THz pulse emitted from femtosecond laser filament in air.

    Science.gov (United States)

    Zhang, Y; Chen, Y; Marceau, C; Liu, W; Sun, Z-D; Xu, S; Théberge, F; Châteauneuf, M; Dubois, J; Chin, S L

    2008-09-29

    Femtosecond laser filament could produce THz wave in forward direction. In our experiment, THz pulse emitted from a femtosecond laser filament has been investigated. It was found that the polarization of the studied THz pulse mainly appears as elliptical. This observation supplements the previous conclusion obtained by C. D'Amico et al. that THz wave emitted by a filament is radially polarized. The mechanism of generating elliptically polarized THz wave has been interpreted by either four-wave optical rectification or second order optical rectification inside the filament zone where centro-symmetry of the air is broken by the femtosecond laser pulse.

  10. The THz Spectrum of Density Fluctuations of Water: The Viscoelastic Regime

    Directory of Open Access Journals (Sweden)

    Alessandro Cunsolo

    2015-01-01

    Full Text Available Relevant advances in the knowledge of the water dynamics at mesoscopic scales are reviewed, while mainly focusing on the contribution provided by high resolution inelastic X-ray scattering (IXS. In particular it is discussed how the use of IXS has improved our understanding of viscoelastic properties of water at THz frequencies. This specifically involves some solid-like features such as the onset of shear wave propagation, a sound velocity surprisingly similar to the one of ice, and an anomalously low sound absorption coefficient. All these properties can be explained by assuming the coupling of THz density fluctuations with a structural relaxation process connected to the breaking and forming of hydrogen bonds (HBs. This review also includes more recent IXS results demonstrating that, upon approaching supercritical conditions, relaxation phenomena in water gradually lose their structural character becoming essentially collisional in character. Furthermore, GHz spectroscopy results on supercooled water, suggesting the occurrence of a structural arrest, are discussed. An overview of the new opportunities offered by next generation IXS spectrometers finally concludes this review.

  11. High Resolution Thz and FIR Spectroscopy of SOCl_2

    Science.gov (United States)

    Martin-Drumel, M. A.; Cuisset, A.; Sadovskii, D. A.; Mouret, G.; Hindle, F.; Pirali, O.

    2013-06-01

    Thionyl chloride (SOCl_2) is an extremely powerful oxidant widely used in industrial processes and playing a role in the chemistry of the atmosphere. In addition, it has a molecular configuration similar to that of phosgene (COCl_2), and is therefore of particular interest for security and defense applications. Low resolution vibrational spectra of gas phase SOCl_2 as well as high resolution pure rotational transitions up to 25 GHz have previously been investigated. To date no high resolution data are reported at frequencies higher than 25 GHz. We have investigated the THz absorption spectrum of SOCl_2 in the spectral region 70-650 GHz using a frequency multiplier chain coupled to a 1 m long single path cell containing a pressure of about 15 μbar. At the time of the writing, about 8000 pure rotational transitions of SO^{35}Cl_2 with highest J and K_a values of 110 and 50 respectively have been assigned on the spectrum. We have also recorded the high resolution FIR spectra of SOCl_2 in the spectral range 50-700 wn using synchrotron radiation at the AILES beamline of SOLEIL facility. A White-type cell aligned with an absorption path length of 150 m has been used to record, at a resolution of 0.001 wn, two spectra at pressures of 5 and 56 μbar of SOCl_2. On these spectra all FIR modes of SOCl_2 are observed (ν_2 to ν_6) and present a resolved rotational structure. Their analysis is in progress. T. J. Johnson et al., J. Phys. Chem. A 107, 6183 (2003) D. E. Martz and R. T. Lagemann, J. Chem. Phys. 22,1193 (1954) H. S. P. Müller and M. C. L. Gerry, J. Chem. Soc. Faraday Trans. 90, 3473 (1994)

  12. Ultrafast nonlinear response of silicon carbide to intense THz fields

    DEFF Research Database (Denmark)

    Tarekegne, Abebe Tilahun; Iwaszczuk, Krzysztof; Kaltenecker, Korbinian J.

    2017-01-01

    We demonstrate ultrafast nonlinear absorption induced by strong, single-cycle THz fields in bulk, lightly doped 4H silicon carbide. A combination of Zener tunneling and intraband transitions makes the effect as at least as fast as the excitation pulse. The sub-picosecond recovery time makes...

  13. Graphene-based THz modulator analyzed by equivalent circuit model

    DEFF Research Database (Denmark)

    Xiao, Binggang; Chen, Jing; Xie, Zhiyi

    2016-01-01

    A terahertz (THz) modulator based on graphene is proposed and analysed by use of equivalent transmission line of a homogeneous mediumand the local anisotropic model of the graphene conductivity. The result calculated by the equivalent circuit is consistent with that obtained byFresnel transfer...

  14. Quantum-dot micropillars for parametric THz emission

    DEFF Research Database (Denmark)

    Mariani, S.; Andronico, A.; Favero, I.

    2013-01-01

    We report on the design, fabrication and optical investigation of AlGaAs microcavities for THz Difference Frequency Generation (DFG) between Whispering Gallery Modes (WGMs), where the pump and DFG wavelengths (λ ≈ 1.3 μm and λ ≈ 75-150 μm, respectively) lie on opposite sides of the Restrahlen band...

  15. Perspective: THz-driven nuclear dynamics from solids to molecules

    Directory of Open Access Journals (Sweden)

    Peter Hamm

    2017-11-01

    Full Text Available Recent years have seen dramatic developments in the technology of intense pulsed light sources in the THz frequency range. Since many dipole-active excitations in solids and molecules also lie in this range, there is now a tremendous potential to use these light sources to study linear and nonlinear dynamics in such systems. While several experimental investigations of THz-driven dynamics in solid-state systems have demonstrated a variety of interesting linear and nonlinear phenomena, comparatively few efforts have been made to drive analogous dynamics in molecular systems. In the present Perspective article, we discuss the similarities and differences between THz-driven dynamics in solid-state and molecular systems on both conceptual and practical levels. We also discuss the experimental parameters needed for these types of experiments and thereby provide design criteria for a further development of this new research branch. Finally, we present a few recent examples to illustrate the rich physics that may be learned from nonlinear THz excitations of phonons in solids as well as inter-molecular vibrations in liquid and gas-phase systems.

  16. Hybrid antiresonant metamaterial waveguides for THz and IR

    DEFF Research Database (Denmark)

    Stefani, Alessio; Lwin, Richard; Argyros, Alexander

    2016-01-01

    We report on a novel waveguide concept which combines antiresonant and metamaterial guidance. The guidance is achieved in the hollow core and loss as low as 2.3 dB/km are theoretically achievable in the THz frequency range. Both purely antiresonant and antiresonant metamaterial fibers have been f...

  17. Fiber Drawn 2D Polymeric Photonic Crystal THz Filters

    DEFF Research Database (Denmark)

    Stecher, Matthias; Jansen, Christian; Ahmadi-Boroujeni, Mehdi

    2012-01-01

    In this paper, we report on different polymeric 2D photonic crystal filters for THz frequencies which are fabricated by a standard fiber drawing technique. The bandstop filters were simulated and designed by the generalized multipole technique (GMT). The frequency and angle dependent transmission...

  18. The Prospects of Ultra-Broadband THz Wireless Communications

    DEFF Research Database (Denmark)

    Yu, Xianbin; Chen, Ying; Galili, Michael

    2014-01-01

    Wireless communications have entered into a path towards Terabit era, to accommodate the increasing demands on fast wireless access, e.g. huge data file transferring and fast mobile data access. Terahertz (THz) technology is considered feasible to carry ultrafast data signals, as it offers up to ...

  19. Electron dynamics in metals and semiconductors in strong THz fields

    DEFF Research Database (Denmark)

    Jepsen, Peter Uhd

    2017-01-01

    Semiconductors and metals respond to strong electric fields in a highly nonlinear fashion. Using single-cycle THz field transients it is possible to investigate this response in regimes not accessible by transport-based measurements. Extremely high fields can be applied without material damage...

  20. THz quantum-confined Stark effect in semiconductor quantum dots

    DEFF Research Database (Denmark)

    Turchinovich, Dmitry; Monozon, Boris S.; Livshits, Daniil A.

    2012-01-01

    We demonstrate an instantaneous all-optical manipulation of optical absorption at the ground state of InGaAs/GaAs quantum dots (QDs) via a quantum-confined Stark effect (QCSE) induced by the electric field of incident THz pulses with peak electric fields reaching 200 kV/cm in the free space...

  1. Enhanced THz extinction in arrays of resonant semiconductor particles

    NARCIS (Netherlands)

    Schaafsma, M. C.; Georgiou, G.; J. Gomez Rivas,

    2015-01-01

    We demonstrate experimentally the enhanced THz extinction by periodic arrays of resonant semiconductor particles. This phenomenon is explained in terms of the radiative coupling of localized resonances with diffractive orders in the plane of the array (Rayleigh anomalies). The experimental results

  2. A new printed fractal right angled isosceles triangular monopole antenna for ultra-wideband applications

    Directory of Open Access Journals (Sweden)

    Manisha Gupta

    2017-03-01

    Full Text Available In this present work, a different right angled isosceles triangular Microstrip patch antenna (RITMA for ultra wideband (UWB utilization is designed. The antenna presented is simple and small in structure. The antenna has a triangular patch with defected ground plane and a notch on the ground surface, which provides a usable bandwidth. By fracturing the antenna a significant improvement in return loss is seen, and good gain is obtained. Results of the proposed antenna show omnidirectional radiation behavior within the UWB frequency range.

  3. Antenna design for propagating spin wave spectroscopy in ferromagnetic thin films

    Science.gov (United States)

    Zhang, Yan; Yu, Ting; Chen, Ji-lei; Zhang, You-guang; Feng, Jian; Tu, Sa; Yu, Haiming

    2018-03-01

    In this paper, we investigate the characteristics of antenna for propagating-spin-wave-spectroscopy (PSWS) experiment in ferromagnetic thin films. Firstly, we simulate the amplitude and phase distribution of the high-frequency magnetic field around antenna by high frequency structure simulator (HFSS). And then k distribution of the antenna is obtained by fast Fourier transformation (FFT). Furthermore, three kinds of antenna designs, i.e. micro-strip line, coplanar waveguide (CPW), loop, are studied and compared. How the dimension parameter of antenna influence the corresponding high-frequency magnetic field amplitude and k distribution are investigated in details.

  4. An Integrated 4-element Slot-Based MIMO and an UWB Sensing Antenna System for CR Platforms

    KAUST Repository

    Hussain, Rifaqat

    2017-12-08

    This paper presents a novel integrated antenna system for cognitive radio (CR) applications. The design consists of a compact 4- element reconfigurable annular slot based multiple-input-multiple-output (MIMO) antenna system integrated within an ultra-wide-band (UWB) sensing antenna. All the antenna elements are planar in structure and designed on a single substrate (RO-4350) with dimensions 60×120×1.5 mm3. The frequency reconfigurable slot based MIMO antenna system is tuned over a wide frequency band from 1.77 GHz to 2.51 GHz while the UWB sensing antenna is covering from 0.75~7.65 GHz The proposed antenna system is suitable for CR enabled wireless devices. The envelope correlation coefficient (ECC) did not exceed 0.248 in the entire operating band of the MIMO antenna part. The maximum measured gain of the MIMO antenna is 3.2 dBi with maximum efficiency of 81%.

  5. Experimental analysis of THz receiver performance in 80 Gbit/s communication system

    DEFF Research Database (Denmark)

    Jia, Shi; Yu, Xianbin; Hu, Hao

    2016-01-01

    We experimentally analyze the performance of Schottky mixer-based THz receiver in a high-speed THz wireless transmission system incorporating an ultra-broadband uni-travelling carrier photodiode (UTC-PD) as photo-mixing emitter. The multi-channel photonic THz wireless system operates in the 375–4...... in the receiver however severely affects the receiver bandwidth and induces the performance degradation of THz wireless communication systems.......We experimentally analyze the performance of Schottky mixer-based THz receiver in a high-speed THz wireless transmission system incorporating an ultra-broadband uni-travelling carrier photodiode (UTC-PD) as photo-mixing emitter. The multi-channel photonic THz wireless system operates in the 375...

  6. Gas Phase Thz Spectroscopy of Organosulfide and Organophosphorous Compounds Using a Synchrotron Source

    Science.gov (United States)

    Cuisset, Arnaud; Smirnova, Irina; Bocquet, Robin; Hindle, Francis; Mouret, Gael; Sadovskii, Dmitrii A.; Pirali, Olivier; Roy, Pascale

    2011-06-01

    This study concerns the gas phase rovibrational spectroscopy of organosulfide and organophosphorous which are considered as non toxic model compounds in the analysis of chemical weapon materials, high pathogenic and mutagenic agents, and other environmentally interesting air-borne species. The coupling of the synchrotron radiation with multipass cells and the FTIR spectrometer allowed to obtain very conclusive results in term of sensitivity and resolution and improved the previous results obtained with classical sources. For DMSO, using an optical path of 150 m the spectra have been recorded at the ultimate resolution of 0.001 Cm-1 allowing to fully resolve the rotational structure of the lowest vibrational modes observed in the THz region. In the 290 - 420 Cm-1 region, the rovibrational spectrum of the "perpendicular" and "parallel" vibrational bands associated with, respectively, the asymmetric ν23 and symmetric ν11 bending modes of DMSO have been recorded with a resolution of 1.5× 10-3 Cm-1. The gas phase vibrational spectra of organophosphorous compounds were measured by FTIR spectroscopy using the vapor pressure of the compounds. Except for TBP, the room temperature vapor pressure was sufficient to detect all active vibrational modes from THz to NIR domain. Contrary to DMSO, the rotational patterns of alkyl phosphates and alkyl phosphonates could not be resolved; only a vibrational analysis may be performed. Nevertheless, the spectral fingerprints observed in the THz region allowed a clear discrimination between the molecules and between the different molecular conformations. A. Cuisset, G. Mouret, O. Pirali, P. Roy, F. Cazier, H. Nouali, J. Demaison, J. Phys. Chem. B, 2008, 112:, 12516-12525 A. Cuisset, L. Nanobashvili, I. Smirnova, R. Bocquet, F. Hindle, G. Mouret, O. Pirali, P. Roy and D. A. Sadovskií, Chem. Phys. Lett., 2010, 492: 30-34 I. Smirnova, A. Cuisset, R. Bocquet, F. Hindle, G. Mouret, O. Pirali, P. Roy, J. Phys. Chem. B, 2010, 114: 16936-16947.

  7. Antenna selection in a SIMO architecture for HF radio links

    Science.gov (United States)

    Erhel, Yvon; Lemur, Dominique; Oger, Martial; Le Masson, Jérôme

    2016-03-01

    This work takes place in the global design of a SIMO architecture (single input multiple output) for transhorizon radio links, aiming at a significant increase in the data rate when compared with standard modems based in general on a SISO scheme (single input single output). The project is subject to available space constraints at the receive end, involving mobile stations or onboard implementation. We consider solutions that appear as extensions of the compact and heterogeneous antenna array that we proposed previously: collocated antennas of different types are set up with the same phase center and present diversity in their polarization sensitivities to make array processing effective. Given the number NC of receive channels, we address the problem of selecting the most effective antennas in a set of NA possible candidates including monopoles, dipoles, loop antennas with various geometries, and orientations. The criterion to be maximized is the SIMO outage capacity, a quantity based on the statistical distribution of the SIMO Shannon capacity estimated for a large number of ionospheric channel realizations, each of them being quantified by its channel impulse response including the receive antenna directional responses. Results are presented in the context of a 1 × 2 SIMO structure: the identification of the two most effective antennas in a set of NA = 15 sensors indicates that the optimal structures involve two orthogonal horizontal dipoles or two vertical orthogonal loop antennas. In these conditions, the outage capacity reaches up to 2.23 bps/Hz, a value that significantly exceeds the performances of standard modems.

  8. Direct Conversion of Free Space Millimeter Waves to Optical Domain by Plasmonic Modulator Antenna.

    Science.gov (United States)

    Salamin, Yannick; Heni, Wolfgang; Haffner, Christian; Fedoryshyn, Yuriy; Hoessbacher, Claudia; Bonjour, Romain; Zahner, Marco; Hillerkuss, David; Leuchtmann, Pascal; Elder, Delwin L; Dalton, Larry R; Hafner, Christian; Leuthold, Juerg

    2015-12-09

    A scheme for the direct conversion of millimeter and THz waves to optical signals is introduced. The compact device consists of a plasmonic phase modulator that is seamlessly cointegrated with an antenna. Neither high-speed electronics nor electronic amplification is required to drive the modulator. A built-in enhancement of the electric field by a factor of 35,000 enables the direct conversion of millimeter-wave signals to the optical domain. This high enhancement is obtained via a resonant antenna that is directly coupled to an optical field by means of a plasmonic modulator. The suggested concept provides a simple and cost-efficient alternative solution to conventional schemes where millimeter-wave signals are first converted to the electrical domain before being up-converted to the optical domain.

  9. 47 CFR 80.866 - Spare antenna.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Spare antenna. 80.866 Section 80.866... Spare antenna. A spare transmitting antenna completely assembled for immediate erection must be provided. If the installed transmitting antenna is suspended between supports, this spare antenna must be a...

  10. 47 CFR 80.863 - Antenna system.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Antenna system. 80.863 Section 80.863... Antenna system. (a) An antenna system must be installed which is as nondirectional and as efficient as is... construction of the required antenna must insure operation in time of emergency. (b) If the required antenna is...

  11. 47 CFR 73.69 - Antenna monitors.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Antenna monitors. 73.69 Section 73.69... Broadcast Stations § 73.69 Antenna monitors. (a) Each station using a directional antenna must have in operation at the transmitter site an FCC authorized antenna monitor. (b) In the event that the antenna...

  12. Antennas for VHF/UHF personal radio: A theoretical and experimental study of characteristics and performance

    DEFF Research Database (Denmark)

    Andersen, Jørgen Bach; Hansen, Flemming

    1977-01-01

    A theoretical analysis of the characteristics of small personal radio antennas for the 68- to 470-MHz frequency range is given. Representing the human body by a simplified lossy dielectric structure, the influence of the body on the performance of the antenna is investigated in detail, and it is ......A theoretical analysis of the characteristics of small personal radio antennas for the 68- to 470-MHz frequency range is given. Representing the human body by a simplified lossy dielectric structure, the influence of the body on the performance of the antenna is investigated in detail...... increase the antenna efficiency considerably, indicating that even very short antennas may provide acceptable radiation efficiencies. The results of the theoretical work are supported by measurements on practical antennas. Quarter-wave and short antennas of the helical type are compared with respect...... to efficiency and radiation patterns at 80, 160, and 450 MHz, and it is demonstrated how the physical length of the antenna affects the antenna performance. The design of a very short and compact personal radio antenna is described....

  13. Monostatic ultra-wideband GPR antenna for through wall detection

    Directory of Open Access Journals (Sweden)

    Ali Jawad

    2017-01-01

    Full Text Available The aim of this paper is to present a monostatic arc-shaped ultra-wideband (UWB printed monopole antenna system with 3-16 GHz frequency bandwidth suitable for through-wall detection. Ground penetrating radar (GPR technique is used for detection with the gain of 6.2 dB achieved for the proposed antenna using defected ground structure (DGS method. To serve the purpose, a simulation experiment of through-wall detection model is constructed which consists of a monostatic antenna act as transmitter and receiver, concrete wall and human skin model. The time domain reflection of obtained result is then analysed for target detection.

  14. Design and development of a small compact ultra wideband antenna

    International Nuclear Information System (INIS)

    Qurratulain; Chattoraj, Neela

    2013-01-01

    In this paper the design of a novel and compact U slot UWB printed monopole microstrip antenna of size 19.2 × 28.8 mm 2 has been presented for wireless applications. The planar, small and thin UWB antenna design consists of a U slot radiator fed by a single 50Ω microstrip line with truncated ground plane is excited by a coaxial SMA connector. The simulations are done using the Ansoft High Frequency Structure Simulator (HFSS) software tool. The simulated results of impedance bandwidth are well supported by measurement. The measured group delay and radiation pattern results are also presented and performance of the antenna is analyzed/discussed.

  15. Monostatic ultra-wideband GPR antenna for through wall detection

    Science.gov (United States)

    Ali, Jawad; Abdullah, Noorsaliza; Yahya, Roshayati; Naeem, Taimoor

    2017-11-01

    The aim of this paper is to present a monostatic arc-shaped ultra-wideband (UWB) printed monopole antenna system with 3-16 GHz frequency bandwidth suitable for through-wall detection. Ground penetrating radar (GPR) technique is used for detection with the gain of 6.2 dB achieved for the proposed antenna using defected ground structure (DGS) method. To serve the purpose, a simulation experiment of through-wall detection model is constructed which consists of a monostatic antenna act as transmitter and receiver, concrete wall and human skin model. The time domain reflection of obtained result is then analysed for target detection.

  16. Design and development of a small compact ultra wideband antenna

    Science.gov (United States)

    Qurratulain; Chattoraj, Neela

    2013-04-01

    In this paper the design of a novel and compact U slot UWB printed monopole microstrip antenna of size 19.2 × 28.8 mm2 has been presented for wireless applications. The planar, small and thin UWB antenna design consists of a U slot radiator fed by a single 50Ω microstrip line with truncated ground plane is excited by a coaxial SMA connector. The simulations are done using the Ansoft High Frequency Structure Simulator (HFSS) software tool. The simulated results of impedance bandwidth are well supported by measurement. The measured group delay and radiation pattern results are also presented and performance of the antenna is analyzed/discussed.

  17. Very Compact and Broadband Active Antenna for VHF Band Applications

    Directory of Open Access Journals (Sweden)

    Y. Taachouche

    2012-01-01

    Full Text Available An active receiving antenna with small size consisting of a monopole loaded with a transistor bipolar is presented in this paper. A transistor is used in order to miniaturize the receiving active antenna size in VHF band. The vertical size of the structure is equal to λ/175, where λ is the wavelength at the lower frequency of the bandwidth. Despite the very small size of the antenna, the frequency bandwidth is very wide and the gain is suitable for FM application with sensitive receivers.

  18. Double dipole antenna SIS receivers at 100 and 400 GHz

    Science.gov (United States)

    Skalare, A.; Vandestadt, H.; Degraauw, T.; Panhuyzen, R. A.; Dierichs, M. M. T. M.

    1992-01-01

    Antenna patterns were measured between 95 and 120 GHz for a double dipole antenna / ellipsoidal lens combination. The structure produces a non-astigmatic beam with low side lobe levels over that whole band. A heterodyne SIS receiver based on this concept gave a best noise temperature of 145 K DSB at 98 GHz. Measurements were also made with a 400 GHz heterodyne SIS receiver, using a double dipole antenna in conjunction with a hyperhemispherical lens. The best noise temperature was 220 K DSB at 402 GHz. On-chip stubs were used to tune out the SIS junction capacitance.

  19. Base Station Antenna Pattern Distortion in Practical Urban Deployment Scenarios

    DEFF Research Database (Denmark)

    Rodriguez Larrad, Ignacio; Nguyen, Huan Cong; Sørensen, Troels Bundgaard

    2014-01-01

    In real urban deployments, base station antennas are typically not placed in free space conditions. Therefore, the radiation pattern can be affected by mounting structures and nearby obstacles located in the proximity of the antenna (near-field), which are often not taken into consideration. Also...... presents a combination of near-field and far-field simulations aimed to provide an overview of the distortion experienced by the base station antenna pattern in two different urban deployment scenarios: rooftop and telecommunications tower. The study illustrates how, in comparison with the near...

  20. A Compact UWB Diversity Antenna

    Directory of Open Access Journals (Sweden)

    Hui Zhao

    2014-01-01

    Full Text Available A compact printed ultrawideband (UWB diversity antenna with a size of 30 mm × 36 mm operating at a frequency range of 3.1–10.6 GHz is proposed. The antenna is composed of two semielliptical monopoles fed by two microstrip lines. Two semicircular slots, two rectangular slots, and one stub are introduced in the ground plane to adjust the impedance bandwidth of the antenna and improve the isolation between two feeding ports. The simulated and measured results show that impedance bandwidth of the proposed antenna can cover the whole UWB band with a good isolation of < −15 dB. The radiation patterns, peak antenna gain, and envelope correlation coefficient are also measured and discussed. The measured results show that the proposed antenna can be a good candidate for some portable MIMO/diversity UWB applications.

  1. Efficient Placement of Directional Antennas

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Feng [Los Alamos National Laboratory; Kasiviswanathan, Shiva [Los Alamos National Laboratory

    2010-09-20

    Directional antenna is an technology for the proliferation of wireless networks. In centralized wireless network, wireless devices communicate through base stations. Directed antennas are placed on base stations and form a backbone of communication. The communication between base stations and wireless devices can be interfered due to a large number of wireless device. Methodically positioning and orienting directed antennas can help to reduce the interference while saving energy. An integer linear programming is developed for siting and directing antennas on multiple base stations, and this formulation can be extended to model non-overlapping channels. Through the integer programming formulation, optimal antenna positions can be used to analyze the performance of directed antennas with different parameters like the number base stations and the number of non-overlapping channels.

  2. Far-infrared cw difference-frequency generation using vertically integrated and planar low temperature grown GaAs photomixers: application to H2S rotational spectrum up to 3 THz

    Science.gov (United States)

    Mouret, G.; Matton, S.; Bocquet, R.; Hindle, F.; Peytavit, E.; Lampin, J. F.; Lippens, D.

    2004-10-01

    The generation of continuous coherent THz radiation by mixing two cw Ti:Sa laser beams with a well-controlled frequency separation for a new scheme of vertically integrated low temperature grown GaAs (LTG-GaAs) spiral photomixer is reported. For this new photomixer device used in THz emission, the LTG-GaAs active layer is sandwiched between the two parallel metal plates of a high-speed photodetector loaded by a broadband spiral antenna. We have exploited the advantage of a higher delivered power in the low part of the spectrum (<2000 GHz), while a low RC time constant planar interdigitated detector was used at the upper frequency. The performances of the spectroscopic setup in terms of spectral resolution (5 MHz), tunability and frequency capability are assessed by measurements of the pure rotational spectra of hydrogen sulfide (H2S) up to 3000 GHz.

  3. UWB Directive Triangular Patch Antenna

    Directory of Open Access Journals (Sweden)

    A. C. Lepage

    2008-01-01

    Full Text Available Compact directive UWB antennas are presented in this paper. We propose an optimization of the F-probe fed triangular patch antenna. The new design achieves an impedance bandwidth of 69% (3–6.15 GHz and presents good radiation characteristics over the whole impedance bandwidth. The average gain is 6.1 dB. A time-domain study has been performed to characterize the antenna behavior in case a UWB pulse is used. Finally, we propose an alternative solution to facilitate the manufacturing process using metallized foam technology. It also improves the robustness of the antenna as well as reducing its cost.

  4. Antenna arrays a computational approach

    CERN Document Server

    Haupt, Randy L

    2010-01-01

    This book covers a wide range of antenna array topics that are becoming increasingly important in wireless applications, particularly in design and computer modeling. Signal processing and numerical modeling algorithms are explored, and MATLAB computer codes are provided for many of the design examples. Pictures of antenna arrays and components provided by industry and government sources are presented with explanations of how they work. Antenna Arrays is a valuable reference for practicing engineers and scientists in wireless communications, radar, and remote sensing, and an excellent textbook for advanced antenna courses.

  5. Hybrid Maritime Satellite Communication Antenna

    DEFF Research Database (Denmark)

    Smith, Thomas Gunst

    Hybrid antennas for a maritime satellite communication terminal with simultaneous operation at L- and Ka-band have been investigated. The frequency bands of interest are 1; 525:0 1; 660:5 MHz (RX+TX, RHCP), 19:7 20:2 (RX, LHCP) and 29:5 30:0 GHz (TX, RHCP), which are all part of the Inmarsat BGAN....... The Ka-band dual-reflector is inherently a high-gain and low-loss antenna, and investigations show negligible impact of the L-band backfire helical antenna. Therfore, this hybrid single/dual-reflector antenna presents a viable solution to the combined L- and Ka-band antenna. Novel hybrid antennas...... on the performance of an L-band antenna radiating through the FSS. From these investigations, it is concluded that the FSS antenna concept is well suited for hybrid L- and Ka-band operation. A printed reflectarray antenna with FSS ground-plane is demonstrated. The reflectarray produces a collimated beam as a curved...

  6. Development and coupling analysis of active skin antenna

    Science.gov (United States)

    Zhou, Jinzhu; Huang, Jin; He, Qingqang; Tang, Baofu; Song, Liwei

    2017-02-01

    An active skin antenna is a multifunctional composite structure that can provide load-bearing structure and steerable beam pointing functions, and is usually installed in the structural surface of aircraft, warships, and armored vehicles. This paper presents an innovative design of the active skin antenna, which consists of a package layer, control and signal processing layer, and RF (radio frequency) layer. The RF layer is fabricated by low temperature co-fired ceramics, with 64 microstrip antenna elements, tile transmitting and receiving modules, microchannel heat sinks, and feeding networks integrated into a functional block 2.8 mm thick. In this paper, a full-sized prototype of an active skin antenna was designed, fabricated, and tested. Moreover, a coupling analysis method was presented to evaluate the mechanical and electromagnetic performance of the active skin antenna subjected to aerodynamic loads. A deformed experimental system was built to validate the effectiveness of the coupling analysis method, which was also implemented to evaluate the performance of the active skin antenna when subjected to aerodynamic pressure. The fabricated specimen demonstrated structural configuration feasibility, and superior environmental load resistance.

  7. Compact Penta-Band Dual ZOR Antenna for Mobile Applications

    Directory of Open Access Journals (Sweden)

    Jae-Gon Lee

    2016-01-01

    Full Text Available A compact penta-band dual zeroth order resonator (ZOR antenna with band-stop filter is proposed for mobile applications. The ZOR antenna is designed with modified mushroom-like structures extended on nonground region to obtain good efficiency and broad bandwidth. This modified mushroom-like structure is confirmed as double negative (DNG transmission line by full wave simulated dispersion relation. Moreover, a bended patch and a band-stop filter (BSF are employed to increase efficiency and bandwidth, respectively. The length of each antenna is about λ0/10 at the resonant frequencies of 900 MHz and 1800 MHz, respectively. The overall dimension of the antenna is 54.4 mm (length × 4 mm (width × 5 mm (height. The total efficiencies in low and high bands are measured more than 40% and 70%, respectively.

  8. Novel Time-domain Ultra-wide Band TEM Horn Antenna for Highway GPR Applications

    Directory of Open Access Journals (Sweden)

    Yin De

    2017-12-01

    Full Text Available Based on transmission line theory and impedance transition, we design an ultra-wideband Transverse ElectroMagnetic (TEM horn antenna that takes advantage of index gradient structure and loading techniques and is optimized for highway Ground Penetrating Radar (GPR applications. We use numerical simulation to analyze the effects of different curved surfaces as an extension of the antenna and further improve the antenna performance by the use of a metallic reflective cavity and distributed resistor loading. We then fabricated an antenna based on the optimization results and determined the Voltage Standing Wave Ratio (VSWR of the antenna to be less than 2 for bandwidths ranging from 0.9–12.6 GHz. The waveform fidelity of the antenna is also good and when we applied this antenna to highway scenarios, it achieved good results.

  9. Experimental Study on Thermal Vacuum Environment Sensitivity of Spacecraft Antenna's Typical Failure

    Directory of Open Access Journals (Sweden)

    Bi Yanqiang

    2017-01-01

    Full Text Available With the development of space applications, spacecraft antenna has become an indispensable part of any space system. The spacecraft antenna affects and constrains the performance and functionality of the entire wireless communication system as well as the entire spacecraft. Spacecraft antenna has to withstand the noise, vibration, shock and acceleration as launched, and weightlessness, high vacuum, radiation, extreme hot and cold alternating space environment on-orbit[1].The influence of different environmental factors on the typical failure modes of spacecraft antenna is different. The environmental adaptability of the spacecraft antenna depends mainly on its structural design, material, process and other factors. In this paper, the influence of different environmental factors on the typical failure modes of the spacecraft antenna is studied. The sensitivity analysis of the typical failure modes of the thermal vacuum environment is verified by experiments, which provides support for the development of the spacecraft antenna.

  10. Investigation of a Random-Fractal Antenna Based on a Natural Tree-Leaf Geometry

    Directory of Open Access Journals (Sweden)

    Hatem Rmili

    2017-01-01

    Full Text Available In this paper, we investigate a new printed antenna based on the 2D image of a fractal tree-leaf geometry by studying the effect of the irregular boundary of the proposed antenna on its radiation characteristics. Both the impedance matching properties and the radiation patterns of the antenna are studied over the frequency band 1–6 GHz. Four configurations are designed by increasing the complexity of the structure, which ranges from iteration 0 to iteration 3. The fractal properties of the proposed tree-leaf antenna are then compared to those of a conventional fractal antenna with smooth edges. Following this, the proposed antennas are fabricated and characterized experimentally. Finally, results are analyzed and discussed, and a practical application for this new type of antennas is proposed.

  11. The analysis of reactively loaded microstrip antennas by finite difference time domain modelling

    Science.gov (United States)

    Hilton, G. S.; Beach, M. A.; Railton, C. J.

    1990-01-01

    In recent years, much interest has been shown in the use of printed circuit antennas in mobile satellite and communications terminals at microwave frequencies. Although such antennas have many advantages in weight and profile size over more conventional reflector/horn configurations, they do, however, suffer from an inherently narrow bandwidth. A way of optimizing the bandwidth of such antennas by an electronic tuning technique using a loaded probe mounted within the antenna structure is examined, and the resulting far-field radiation patterns are shown. Simulation results from a 2D finite difference time domain (FDTD) model for a rectangular microstrip antenna loaded with shorting pins are given and compared to results obtained with an actual antenna. It is hoped that this work will result in a design package for the analysis of microstrip patch antenna elements.

  12. Performances study of UWB monopole antennas using half-elliptic radiator conformed on elliptical surface

    Science.gov (United States)

    Djidel, S.; Bouamar, M.; Khedrouche, D.

    2016-04-01

    This paper presents a performances study of UWB monopole antenna using half-elliptic radiator conformed on elliptical surface. The proposed antenna, simulated using microwave studio computer CST and High frequency simulator structure HFSS, is designed to operate in frequency interval over 3.1 to 40 GHz. Good return loss and radiation pattern characteristics are obtained in the frequency band of interest. The proposed antenna structure is suitable for ultra-wideband applications, which is, required for many wearable electronics applications.

  13. Vlasov Antenna Data for Electromagnetic Code Validation

    National Research Council Canada - National Science Library

    Greenwood, Andrew

    2003-01-01

    Measured antenna data is provided for validating computational electromagnetic (CEM) computer programs. The subject antenna is the Vlasov antenna, which is formed by cutting a hollow circular cylindrical waveguide at an oblique angle...

  14. Flight termination system equipment. Volume 1: Antennas and antenna couplers

    Science.gov (United States)

    This document is the result of the efforts of the Flight Termination System Ad Hoc Committee of the Range Safety Group, Range Commanders Council. The Flight Termination System Equipment Catalog provides a ready reference to missile antennas and antenna couplers used at U.S. missile ranges and test facilities. Since use of each antenna/antenna coupler must be approved by the Range Commander with the in-flight range safety responsibility, inclusion in this catalog does not constitute sanction of such use nor approval for use on other missiles/space vehicles on the same range or on the same missile/space vehicle on other ranges. This catalog is not intended to be a comprehensive review of all flight termination antennas/antenna couplers available on the open market. The information contained in this publication has been provided by the manufacturer or extracted from manufacturers' specifications and is provided only as a guide. No conclusions are to be implied or assumed relative to the merits of one antenna/antenna coupler versus another. Where applicable, a history of the flight usage has been provided.

  15. Ultra wide band antennas

    CERN Document Server

    Begaud, Xavier

    2013-01-01

    Ultra Wide Band Technology (UWB) has reached a level of maturity that allows us to offer wireless links with either high or low data rates. These wireless links are frequently associated with a location capability for which ultimate accuracy varies with the inverse of the frequency bandwidth. Using time or frequency domain waveforms, they are currently the subject of international standards facilitating their commercial implementation. Drawing up a complete state of the art, Ultra Wide Band Antennas is aimed at students, engineers and researchers and presents a summary of internationally recog

  16. Antennas on circular cylinders

    DEFF Research Database (Denmark)

    Knudsen, H. L.

    1959-01-01

    On the basis of the results obtained by Silver and Saunders [4] for the field radiated from an arbitrary slot in a perfectly conducting circular cylinder, expressions have been derived for the field radiated by a narrow helical slot, with an arbitrary aperture field distribution, in a circular...... antenna in a circular cylinder. By a procedure similar to the one used by Silver and Saunders, expressions have been derived for the field radiated from an arbitrary surface current distribution on a cylinder surface coaxial with a perfectly conducting cylinder. The cases where the space between the two...

  17. Improvement on a 2 × 2 Elements High-Gain Circularly Polarized Antenna Array

    Directory of Open Access Journals (Sweden)

    C. Liu

    2015-01-01

    Full Text Available A novel antipodal Vivaldi antenna with tapering serrated structure at the edges is proposed. Compared with traditional Vivaldi antennas without serrated structure, the gain of the designed antenna is significantly improved in the desired frequency band (4.5–7.5 GHz. In addition, a 2 × 2 Vivaldi antenna array with an orthorhombic structure is designed and fabricated to achieve a circular polarization (CP characteristic. With this configuration, the 3 dB axial ratio bandwidth of the array reaches about 42% with respect to the center frequency of 6 GHz and a high gain is achieved as well. The novel Vivaldi antenna and CP antenna array both have ultrawide band (UWB and high-gain characteristics, which may be applied to the field of commercial communication, remote sensing, and so forth.

  18. UWB and SWB Planar Antenna Technology

    OpenAIRE

    Zhong, Shun-Shi

    2010-01-01

    The recent progress in the development of UWB planar antenna technology has been reviewed. Some types of UWB metal-plate monopole antennas, UWB printed monopole antennas and UWB printed slot antennas are presented. The comparison results of indicate that the UWB printed monopole antennas can realize relatively smaller dimensions, and that the UWB printed slot antennas can achieve relatively higher gain. Finally, some realization manners of the band-notch function of UWB printed monopole anten...

  19. Ultra wideband antennas design, methodologies, and performance

    CERN Document Server

    Galvan-Tejada, Giselle M; Jardón Aguilar, Hildeberto

    2015-01-01

    Ultra Wideband Antennas: Design, Methodologies, and Performance presents the current state of the art of ultra wideband (UWB) antennas, from theory specific for these radiators to guidelines for the design of omnidirectional and directional UWB antennas. Offering a comprehensive overview of the latest UWB antenna research and development, this book:Discusses the developed theory for UWB antennas in frequency and time domainsDelivers a brief exposition of numerical methods for electromagnetics oriented to antennasDescribes solid-planar equivalen

  20. Nimbus-7 SMMR Antenna Temperatures, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — The SMMR Antenna Temperatures (Nimbus-7) data set consists of antenna temperatures from passive microwave radiometers aboard NOAA's Nimbus-7 satellite. The...