Electrochemical behavior of CIGS electrodeposition for applications to photovoltaic cells

Energy Technology Data Exchange (ETDEWEB)

Lee, Hyunju; Ji, Changwook; Kim, Yangdo; Hwang, Yoonhwae [Pusan National University, Busan (Korea, Republic of); Lee, Jaeho [Hongik University, Seoul (Korea, Republic of); Jo, Ilguk [Colorado School of Mines, Golden, CO (United States); Kim, Hyoungchan [Korea Institute of Industrial Technology, Busan (Korea, Republic of)

2014-04-15

The electrodeposition mechanism of Cu(In,Ga)Se{sub 2} (CIGS) thin films on ITO substrates was examined by using cyclic voltammetry (CV). The CV study was performed in unitary In, binary In-Se, ternary Cu-In-Se, and quaternary Cu-In-Ga-Se systems. CV of the Cu-In-Ga-Se system revealed a reduction peak at -0.6 V with the addition of GaCl{sub 3} and showed that the current density was affected significantly by the concentrations of GaCl{sub 3} and InCl{sub 3}. This is probably due to the adsorption-site competition between In{sup 3+} and Ga{sup 3+} on the electrode surface. Energy dispersive X-ray spectroscopy confirmed the CV results. The composition of Ga in the CIGS films increased with increasing concentration of GaCl{sub 3} in the electrolyte whereas the composition of In decreased sharply. The as-deposited films were annealed at 500 .deg. C in a N{sub 2} atmosphere for crystallization. XRD revealed three major peaks corresponding to the (112), (220) and (312) planes of CIGS chalcopyrite respectively. On the other hand, a secondary phase, such as In{sub 4}Se{sub 3}, was observed in the CIGS films containing a high In composition.

A Novel Semiconductor CIGS Photovoltaic Material and Thin-Film ED Technology

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

In order to achieve low-cost high-efficiency thin-film solar cells, a novel Semiconductor Photovoltaic (PV) active material CuIn1-xGaxSe2 (CIGS) and thin-film Electro-Deposition (ED) technology is explored. Firstly,the PV materials and technologies is investigated, then the detailed experimental processes of CIGS/Mo/glass structure by using the novel ED technology and the results are reported. These results shows that high quality CIGS polycrystalline thin-films can be obtained by the ED method, in which the polycrystalline CIGS is definitely identified by the (112), (204, 220) characteristic peaks of the tetragonal structure, the continuous CIGS thin-film layers with particle average size of about 2μm of length and around 1.6μm of thickness. The thickness and solargrade quality of CIGS thin-films can be produced with good repeatability. Discussion and analysis on the ED technique, CIGS energy band and sodium (Na) impurity properties, were also performed. The alloy CIGS exhibits not only increasing band-gap with increasing x, but also a change in material properties that is relevant to the device operation. The beneficial impurity Na originating from the low-cost soda-lime glass substrate becomes one prerequisite for high quality CIGS films. These novel material and technology are very useful for low-cost high-efficiency thin-film solar cells and other devices.

Photovoltaic manufacturing cost and throughput improvements for thin-film CIGS-based modules: Phase 1 technical report, July 1998--July 1999

Energy Technology Data Exchange (ETDEWEB)

Wiedeman, S.; Wendt, R.G.

2000-03-01

The primary objectives of the Global Solar Energy (GSE) Photovoltaic Manufacturing Technology (PVMaT) subcontract are directed toward reducing cost and expanding the production rate of thin-film CuInGaSe{sub 2} (CIGS)-based PV modules on flexible substrates. Improvements will be implemented in monolithic integration, CIGS deposition, contact deposition, and in-situ CIGS control and monitoring. In Phase 1, GSE has successfully attacked many of the highest risk aspects of each task. All-laser, selective scribing processes for CIGS have been developed, and many end-of-contract goals for scribing speed have been exceeded in the first year. High-speed ink-jet deposition of insulating material in the scribes now appears to be a viable technique, again exceeding some end-of-contract goals in the first year. Absorber deposition of CIGS was reduced corresponding to throughput speeds of up to 24-in/min, also exceeding an end-of-contract goal. Alternate back-contact materials have been identified that show potential as candidates for replacement of higher-cost molybdenum, and a novel, real-time monitoring technique (parallel-detector spectroscopic ellipsometry) has shown remarkable sensitivity to relevant properties of the CIGS absorber layer for use as a diagnostic tool. Currently, one of the bilayers has been baselined by GSE for flexible CIGS on polymeric substrates. Resultant back-contacts meet sheet-resistance goals and exhibit much less intrinsic stress than Mo. CIGS has been deposited, and resultant devices are comparable in performance to pure Mo back-contacts. Debris in the chamber has been substantially reduced, allowing longer roll-length between system cleaning.

Thin-Film CIGS Photovoltaic Technology; Annual Technical Report, Phase I; 16 April 1998 - 15 April 1999

International Nuclear Information System (INIS)

Chorobski, D.; Delahoy, A.E.; Kiss, Z.J.; Ziobro, F.

1999-01-01

This report describes work performed by Energy Photovoltaics, Inc. (EPV) under Phase I of this subcontract. EPV's new FORNAX process for CIGS formation is capable of producing devices with high Voc ( and gt;600 mV) and no dark aging effects. Parameters of the best device so far are Voc= 611 mV, Jsc= 27.5 mA/cm2, FF= 74.5%, and efficiency= 12.5%. A 34-cm2 16-cell minimodule was produced using FORNAX CIGS with Voc= 9.58 V, Isc= 52.0 mA, FF69.8%, and efficiency= 10.2%. A new version of EPV's linear evaporation source was developed with improved rate and uniformity for Cu deposition over a width of 45 cm. Using the new linear source, the FORNAX process was implemented on 0.43-m2 substrates in EPV's CIGS pilot line, with Voc= 537 mV and FF= 70.3% being achieved on a device. The EPV Subteam of the National CIS R and D Team has produced Cd-free ZnO/CIGS devices on NREL CIGS using the ROMEAO process (reaction of metal and atomic oxygen) for ZnO deposition. After soaking, the best device exhibited a Voc of 565 mV and an efficiency of 12.3%. Novel bias drive methods were devised for field soaking/anti-soaking experiments as a function of time and temperature. Scaling laws and an activation energy of 0.51 eV were found. Thermally stimulated capacitance reveals the existence of three distinct contributions to ZnO/CIGS device capacitance, two appearing to be gap-state effects and one related to net doping concentration. The coating time of the sputtered pilot-line ZnO:Al has been reduced by a factor of 3 while maintaining film quality. The deposition rate is 48 A s-1. Plans are under way to increase the substrate size from 0.43 m2 to 0.79 m2

Electrodeposition of ZnO-doped films as window layer for Cd-free CIGS-based solar cells

Science.gov (United States)

Tsin, Fabien; Vénérosy, Amélie; Hildebrandt, Thibaud; Hariskos, Dimitrios; Naghavi, Negar; Lincot, Daniel; Rousset, Jean

2016-02-01

The Cu(In,Ga)Se2 (CIGS) thin film solar cell technology has made a steady progress within the last decade reaching efficiency up to 22.3% on laboratory scale, thus overpassing the highest efficiency for polycrystalline silicon solar cells. High efficiency CIGS modules employ a so-called buffer layer of cadmium sulfide CdS deposited by Chemical Bath Deposition (CBD), which presence and Cd-containing waste present some environmental concerns. A second potential bottleneck for CIGS technology is its window layer made of i-ZnO/ZnO:Al, which is deposited by sputtering requiring expensive vacuum equipment. A non-vacuum deposition of transparent conductive oxide (TCO) relying on simpler equipment with lower investment costs will be more economically attractive, and could increase competitiveness of CIGS-based modules with the mainstream silicon-based technologies. In the frame of Novazolar project, we have developed a low-cost aqueous solution photo assisted electrodeposition process of the ZnO-based window layer for high efficiency CIGS-based solar cells. The window layer deposition have been first optimized on classical CdS buffer layer leading to cells with efficiencies similar to those measured with the sputtered references on the same absorber (15%). The the optimized ZnO doped layer has been adapted to cadmium free devices where the CdS is replaced by chemical bath deposited zinc oxysulfide Zn(S,O) buffer layer. The effect of different growth parameters has been studied on CBD-Zn(S,O)-plated co-evaporated Cu(In,Ga)Se2 substrates provided by the Zentrum für Sonnenenergie-und Wasserstoff-Forschung (ZSW). This optimization of the electrodeposition of ZnO:Cl on CIGS/Zn(S,O) stacks led to record efficiency of 14%, while the reference cell with a sputtered (Zn,Mg)O/ZnO:Al window layer has an efficiency of 15.2%.

Thin-Film CIGS Photovoltaic Technology: Annual Technical Report-Phase II, 16 April 1999-15 April 2000; ANNUAL

International Nuclear Information System (INIS)

Delahoy, A.E.; Bruns, J.; Ruppert, A.; Akhtar, M.; Chen, L.; Kiss, Z.J.

2000-01-01

A summary of Energy Photovoltaics' Phase II work includes the following: (1) EPV has demonstrated that it can sputter a Mo back-contact capable of supporting very high efficiency cell processing. Using EPV Mo, NREL has deposited a 17.1% CIGS cell (no AR coating). EPV believes it can identify the signature of''good'' Mo. The Mo was produced on EPV's 0.43 m(sup 2) pilot-line equipment; (2) EPV has performed compound synthesis for several classes of materials, namely non-Cu precursor materials, Cu-containing materials, and ternary buffer materials. Using a ternary compound synthesized at EPV (ZIS) as an evaporation source material for the buffer layer, a Cd-free CIGS device has been produced having an efficiency of 11.5% (560 mV, 32.1 mA/cm(sup 2), FF 64.3%). The ZIS films are photoconductive, and the devices exhibit no dark-light crossover or light soaking effects; (3) EPV initiated the interest of the University of Oregon in capacitance spectroscopy of CIGS devices. An Urbach tail with characteristic energy E0 and lt; 20meV was identified by transient photocapacitance spectroscopy; (4) Small-area CIGS devices were produced in the pilot-line system with an efficiency of 12.0% (581 mV, 30.1 mA/cm(sup 2), FF 68.7%), and in an R and D-scale system with 13.3% efficiency (569 mV, 34.1 mA/cm(sup 2), FF 68.1%); (5) An improved linear evaporation source for Cu delivery has been developed and was used for CIGS formation in the pilot-line system. The deposition width is 45 cm. This technological''tour de force'' allows EPV to build large-area CIGS systems possessing considerable flexibility. In particular, both EPV's FORNAX process and NREL's 3-stage process have been implemented on the pilot line. A CIGS thickness uniformity of 7% over a 40 cm width has been achieved; (6) A 4-head linear source assembly was designed, constructed, and is in use. Flux monitoring is practiced; (7) Large-area CIGS modules were produced with Voc's up to 36.3 V; (8) EPV has started to construct an

Investigation of Some Transparent Metal Oxides as Damp Heat Protective Coating for CIGS Solar Cells: Preprint

Energy Technology Data Exchange (ETDEWEB)

Pern, F. J.; Yan, F.; Zaaunbrecher, B.; To, B.; Perkins, J.; Noufi, R.

2012-10-01

We investigated the protective effectiveness of some transparent metal oxides (TMO) on CIGS solar cell coupons against damp heat (DH) exposure at 85oC and 85% relative humidity (RH). Sputter-deposited bilayer ZnO (BZO) with up to 0.5-um Al-doped ZnO (AZO) layer and 0.2-um bilayer InZnO were used as 'inherent' part of device structure on CdS/CIGS/Mo/SLG. Sputter-deposited 0.2-um ZnSnO and atomic layer deposited (ALD) 0.1-um Al2O3 were used as overcoat on typical BZO/CdS/CIGS/Mo/SLG solar cells. The results were all negative -- all TMO-coated CIGS cells exhibited substantial degradation in DH. Combining the optical photographs, PL and EL imaging, SEM surface micro-morphology, coupled with XRD, I-V and QE measurements, the causes of the device degradations are attributed to hydrolytic corrosion, flaking, micro-cracking, and delamination induced by the DH moisture. Mechanical stress and decrease in crystallinity (grain size effect) could be additional degrading factors for thicker AZO grown on CdS/CIGS.

Novel in situ resistance measurement for the investigation of CIGS growth in a selenization process

International Nuclear Information System (INIS)

Liu Wei; He Qing; Li Fengyan; Li Changjian; Sun Yun; Tian Jianguo; Li Zubin

2009-01-01

During the selenization process of CIGS thin films, the relation between the element loss rate and the precursor depositions are analyzed. The growth of the CIGS thin films during the selenization process is investigated by the novel in situ resistance measurement, by which the formation of compound semiconductors can be observed directly and simultaneously. Their structures, phase evolutions and element losses are analyzed by XRD and XRF. Based on the experimental results, it can be concluded that the phase transforms have nothing to do with the deposition sequences of precursors, while the element loss rates are related to the deposition sequences in this process. In addition, element loss mechanisms of CIGS thin films prepared by the selenization process are analyzed by the phase evolutions and chemical combined path in the In, Ga–Se reaction processes. Moreover it is verified that the element losses are depressed by increasing the ramping-up rate finally. The results provide effective methods to fabricate high-quality CIGS thin films with low element losses

Novel in situ resistance measurement for the investigation of CIGS growth in a selenization process

Science.gov (United States)

Liu, Wei; Tian, Jian-Guo; Li, Zu-Bin; He, Qing; Li, Feng-Yan; Li, Chang-Jian; Sun, Yun

2009-03-01

During the selenization process of CIGS thin films, the relation between the element loss rate and the precursor depositions are analyzed. The growth of the CIGS thin films during the selenization process is investigated by the novel in situ resistance measurement, by which the formation of compound semiconductors can be observed directly and simultaneously. Their structures, phase evolutions and element losses are analyzed by XRD and XRF. Based on the experimental results, it can be concluded that the phase transforms have nothing to do with the deposition sequences of precursors, while the element loss rates are related to the deposition sequences in this process. In addition, element loss mechanisms of CIGS thin films prepared by the selenization process are analyzed by the phase evolutions and chemical combined path in the In, Ga-Se reaction processes. Moreover it is verified that the element losses are depressed by increasing the ramping-up rate finally. The results provide effective methods to fabricate high-quality CIGS thin films with low element losses.

Thin-Film CIGS Photovoltaic Technology: Annual Technical Report-Phase II, 16 April 1999-15 April 2000

Energy Technology Data Exchange (ETDEWEB)

Delahoy, A.E.; Bruns, J.; Ruppert, A.; Akhtar, M.; Chen, L.; Kiss, Z.J.

2000-08-24

A summary of Energy Photovoltaics' Phase II work includes the following: (1) EPV has demonstrated that it can sputter a Mo back-contact capable of supporting very high efficiency cell processing. Using EPV Mo, NREL has deposited a 17.1% CIGS cell (no AR coating). EPV believes it can identify the signature of ``good'' Mo. The Mo was produced on EPV's 0.43 m{sup 2} pilot-line equipment; (2) EPV has performed compound synthesis for several classes of materials, namely non-Cu precursor materials, Cu-containing materials, and ternary buffer materials. Using a ternary compound synthesized at EPV (ZIS) as an evaporation source material for the buffer layer, a Cd-free CIGS device has been produced having an efficiency of 11.5% (560 mV, 32.1 mA/cm{sup 2}, FF 64.3%). The ZIS films are photoconductive, and the devices exhibit no dark-light crossover or light soaking effects; (3) EPV initiated the interest of the University of Oregon in capacitance spectroscopy of CIGS devices. An Urbach tail with characteristic energy E0 < 20meV was identified by transient photocapacitance spectroscopy; (4) Small-area CIGS devices were produced in the pilot-line system with an efficiency of 12.0% (581 mV, 30.1 mA/cm{sup 2}, FF 68.7%), and in an R and D-scale system with 13.3% efficiency (569 mV, 34.1 mA/cm{sup 2}, FF 68.1%); (5) An improved linear evaporation source for Cu delivery has been developed and was used for CIGS formation in the pilot-line system. The deposition width is 45 cm. This technological ``tour de force'' allows EPV to build large-area CIGS systems possessing considerable flexibility. In particular, both EPV's FORNAX process and NREL's 3-stage process have been implemented on the pilot line. A CIGS thickness uniformity of 7% over a 40 cm width has been achieved; (6) A 4-head linear source assembly was designed, constructed, and is in use. Flux monitoring is practiced; (7) Large-area CIGS modules were produced with Voc's up to 36

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics.

Science.gov (United States)

Eisenberg, Daniel A; Yu, Mengjing; Lam, Carl W; Ogunseitan, Oladele A; Schoenung, Julie M

2013-09-15

Copper-indium-gallium-selenium-sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS₂ p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane. Copyright © 2013 Elsevier B.V. All rights reserved.

Se interlayer in CIGS absorption layer for solar cell devices

Energy Technology Data Exchange (ETDEWEB)

Lee, Seung-Kyu; Sim, Jae-Kwan [Semiconductor Materials Process Laboratory, School of Advanced Materials Engineering, Research Center for Advanced Materials Development, Chonbuk National University, Deokjin-Dong 664-14, Jeonju 561-756 (Korea, Republic of); Kissinger, N.J. Suthan [Department of General Studies, Physics Group, Jubail University College, Royal Commission for Jubail, Jubail 10074 (Saudi Arabia); Song, Il-Seok; Kim, Jin-Soo; Baek, Byung-Joon [Semiconductor Materials Process Laboratory, School of Advanced Materials Engineering, Research Center for Advanced Materials Development, Chonbuk National University, Deokjin-Dong 664-14, Jeonju 561-756 (Korea, Republic of); Lee, Cheul-Ro, E-mail: crlee7@jbnu.ac.kr [Semiconductor Materials Process Laboratory, School of Advanced Materials Engineering, Research Center for Advanced Materials Development, Chonbuk National University, Deokjin-Dong 664-14, Jeonju 561-756 (Korea, Republic of)

2015-06-05

Highlights: • Se interlayer is deposited between the CuGa and CuIn/In/Mo/STS stacked layer. • Both CIG precursor layers were selenized at 500 °C for 1 h. • SIMS depth profile shows that Ga distribution is uniform by Se interlayer. • The efficiency was improved for the CIGS solar cell by Se interlayer. - Abstract: A CIGS absorber layer with high gallium contents in the space-charge region can reduce the carrier recombination and improve the open circuit voltage V{sub oc}. Therefore, controlling Ga grading on top of CIGS thin film solar cells is the main objective of this experiment. To reduce Selenium (Se) vacancy, it is important that the diffusion of Ga elements into Se vacancy between Mo back contact and CIGS absorption layer would be controlled. In order to reduce Se vacancy and confirm Ga inter-diffusion, two CIGS solar cells were fabricated by converting CIG precursor with and without Se interlayer. The copper-indium metallic precursors were fabricated corresponding to the sequence CuIn/In/Mo/STS on stainless steel (STS) substrates by sequential direct current magnetron sputtering while Se layer was evaporated by rapid thermal annealing (RTA) system to obtain a Se/CuIn/In/Mo/STS stack. CuGa precursor layer was also fabricated on the Se/CuIn/In/Mo/STS stack. Finally, both CuGa/Se/CuIn/In/Mo/STS and CuGa/CuIn/In/Mo/STS stacks were selenized at 500 °C for 1 h. It was clearly observed from the secondary ion mass spectroscopy (SIMS) and X-ray diffraction (XRD) that there was a change between the fabricated CIGS absorption layers and the amount of Ga elements. Furthermore, the Ga elements gradually decreased from the top to the bottom layer of the CIGS absorption layer. We also discussed the effect of Se interlayer in the CIGS absorption layer and its influence on the solar cell’s performance.

Se interlayer in CIGS absorption layer for solar cell devices

International Nuclear Information System (INIS)

Lee, Seung-Kyu; Sim, Jae-Kwan; Kissinger, N.J. Suthan; Song, Il-Seok; Kim, Jin-Soo; Baek, Byung-Joon; Lee, Cheul-Ro

2015-01-01

Highlights: • Se interlayer is deposited between the CuGa and CuIn/In/Mo/STS stacked layer. • Both CIG precursor layers were selenized at 500 °C for 1 h. • SIMS depth profile shows that Ga distribution is uniform by Se interlayer. • The efficiency was improved for the CIGS solar cell by Se interlayer. - Abstract: A CIGS absorber layer with high gallium contents in the space-charge region can reduce the carrier recombination and improve the open circuit voltage V oc . Therefore, controlling Ga grading on top of CIGS thin film solar cells is the main objective of this experiment. To reduce Selenium (Se) vacancy, it is important that the diffusion of Ga elements into Se vacancy between Mo back contact and CIGS absorption layer would be controlled. In order to reduce Se vacancy and confirm Ga inter-diffusion, two CIGS solar cells were fabricated by converting CIG precursor with and without Se interlayer. The copper-indium metallic precursors were fabricated corresponding to the sequence CuIn/In/Mo/STS on stainless steel (STS) substrates by sequential direct current magnetron sputtering while Se layer was evaporated by rapid thermal annealing (RTA) system to obtain a Se/CuIn/In/Mo/STS stack. CuGa precursor layer was also fabricated on the Se/CuIn/In/Mo/STS stack. Finally, both CuGa/Se/CuIn/In/Mo/STS and CuGa/CuIn/In/Mo/STS stacks were selenized at 500 °C for 1 h. It was clearly observed from the secondary ion mass spectroscopy (SIMS) and X-ray diffraction (XRD) that there was a change between the fabricated CIGS absorption layers and the amount of Ga elements. Furthermore, the Ga elements gradually decreased from the top to the bottom layer of the CIGS absorption layer. We also discussed the effect of Se interlayer in the CIGS absorption layer and its influence on the solar cell’s performance

Thin film CIGS solar cells with a novel low cost process - Final report

Energy Technology Data Exchange (ETDEWEB)

Tiwari, A. N.; Romanyuk, Y.

2010-01-15

Novel manufacturing routes for efficient and low-cost Cu(In,Ga)Se{sub 2} (called CIGS) thin film solar cells are explored and patented. CIGS has proven its suitability for highly efficient and extremely stable solar cells. The low-cost methods allow impurity free material synthesis, fast large-area deposition, high material utilization and a very short energy payback time with drastically lower manufacturing costs. Two non-vacuum, solution-based approaches are investigated to deposit thin layers of CIGS. The first approach considers incorporation of copper into indium gallium selenide precursor layers by ion-exchange from aqueous or organic solutions. Organic solutions provide faster copper incorporation and do not corrode the metal back contact. Solar cells processed from selenized precursor films exhibit efficiencies of up to 4.1%. The second approach with paste coating of inorganic salt solution results in a solar cell efficiency of 4% (record 6.7%), where further improvements are hindered by the presence of the residual carbon layer. Using alternative organic binders, pre-deposited selenium layers, non-binder recipes helps to avoid the carbon layer although the obtained layers are inhomogeneous and contain impurity phases. A patent for the ion-exchange approach is pending, and the obtained research results on the paste coating approach will be scrutinized during new European FP7 project 'NOVA-CIGS'. (authors)

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

International Nuclear Information System (INIS)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W.; Ogunseitan, Oladele A.; Schoenung, Julie M.

2013-01-01

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS 2 p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane

Nd:YAG laser annealing investigation of screen-printed CIGS layer on PET: Layer annealing method for photovoltaic cell fabrication process

KAUST Repository

Alsaggaf, Ahmed

2014-06-01

Cu(In, Ga)Se2 (CIGS) ink was formulated from CIGS powder, polyvinyl butyral PVB, terpineol and polyester/polyamine co-polymeric dispersant KD-1. Thin films with different thicknesses were deposited on PET substrate using screen-printing followed by heat treatment using a Nd:YAG laser. The structure and morphology of the heated thin films were studied. The characterization of the CIGS powder, ink, and film was done using TGA, SEM, FIB, EDS, and XRD. TGA analysis shows that the CIGS ink is drying at 200 °C, which is well below the decomposition temperature of the PET substrate. It was observed by SEM that 20 pulses of 532nm and 60 mJ/cm2 Nd:YAG laser annealing causes atomic diffusion on the near surface area. Furthermore, FIB cross section images were utilized to monitor the effect of laser annealing in the depth of the layer. Laser annealing effects were compared to as deposited layer using XRD in reference to CIGS powder. The measurement shows that crystallinity of deposited CIGS is retained while EDS quantification and atomic ratio result in gradual loss of selenium as laser energy increases. The laser parameters were tuned in an effort to utilize laser annealing of screen-printed CIGS layer as a layer annealing method for solar cell fabrication process.

Surface Passivation of CIGS Solar Cells Using Gallium Oxide

KAUST Repository

Garud, Siddhartha

2018-02-27

This work proposes gallium oxide grown by plasma-enhanced atomic layer deposition, as a surface passivation material at the CdS buffer interface of Cu(In,Ga)Se2 (CIGS) solar cells. In preliminary experiments, a metal-insulator-semiconductor (MIS) structure is used to compare aluminium oxide, gallium oxide, and hafnium oxide as passivation layers at the CIGS-CdS interface. The findings suggest that gallium oxide on CIGS may show a density of positive charges and qualitatively, the least interface trap density. Subsequent solar cell results with an estimated 0.5 nm passivation layer show an substantial absolute improvement of 56 mV in open-circuit voltage (VOC), 1 mA cm−2 in short-circuit current density (JSC), and 2.6% in overall efficiency as compared to a reference (with the reference showing 8.5% under AM 1.5G).

Sputtered molybdenum thin films and the application in CIGS solar cells

Energy Technology Data Exchange (ETDEWEB)

Zhou, D.; Zhu, H., E-mail: hongbing1982@hotmail.com; Liang, X.; Zhang, C.; Li, Z.; Xu, Y.; Chen, J.; Zhang, L.; Mai, Y., E-mail: yaohuamai@hbu.edu.cn

2016-01-30

Graphical abstract: - Highlights: • Mo thin films are prepared by magnetron sputtering. • The dynamic deposition rate increases with the increasing discharge power. • The surface structure of Mo films varies with discharge power and working pressure. • High efficiency CIGS thin film solar cell of 15.2% has been obtained. - Abstract: Molybdenum (Mo) thin films are prepared by magnetron sputtering with different discharge powers and working pressures for the application in Cu(In, Ga)Se{sub 2} (CIGS) thin film solar cells as back electrodes. Properties of these Mo thin films are systematically investigated. It is found that the dynamic deposition rate increases with the increasing discharge power while decreases with the increasing working pressure. The highest dynamic deposition rate of 15.1 nm m/min is achieved for the Mo thin film deposited at the discharge power of 1200 W and at the working pressure of 0.15 Pa. The achieved lowest resistivity of 3.7 × 10{sup −5} Ω cm is attributed to the large grains in the compact thin film. The discharge power and working pressure have great influence on the sputtered Mo thin films. High efficiency of 12.5% was achieved for the Cu(In, Ga)Se{sub 2} (CIGS) thin film solar cells with Mo electrodes prepared at 1200 W and low working pressures. By further optimizing material and device properties, the conversion efficiency has reached to 15.2%.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W. [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States); Ogunseitan, Oladele A. [University of California, Irvine, Irvine, CA 92697 (United States); Schoenung, Julie M., E-mail: jmschoenung@ucdavis.edu [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States)

2013-09-15

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS{sub 2} p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane.

Real time spectroscopic ellipsometry for analysis and control of thin film polycrystalline semiconductor deposition in photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Koirala, Prakash; Attygalle, Dinesh; Aryal, Puruswottam; Pradhan, Puja; Chen, Jie [Center for Photovoltaics Innovation and Commercialization and Department of Physics and Astronomy, University of Toledo, Toledo, OH 43606 (United States); Marsillac, Sylvain [Department of Electrical and Computer Engineering, Old Dominion University, Norfolk, VA 23529 (United States); Ferlauto, Andre S.; Podraza, Nikolas J.; Collins, Robert W. [Center for Photovoltaics Innovation and Commercialization and Department of Physics and Astronomy, University of Toledo, Toledo, OH 43606 (United States)

2014-11-28

Real time spectroscopic ellipsometry (RTSE) from the near-infrared to ultraviolet has been applied for analysis of the deposition of polycrystalline thin films that form the basis of two key photovoltaic heterojunction configurations, superstrate SnO{sub 2}/CdS/CdTe and substrate Mo/Cu(In{sub 1−x}Ga{sub x})Se{sub 2}/CdS. The focus of this work is to develop capabilities for monitoring and controlling the key steps in the fabrication of these device structures. Analysis of RTSE data collected during sputter deposition of CdS on a rough SnO{sub 2} transparent top contact provides the time evolution of the CdS effective thickness, or film volume per unit substrate area. This thickness includes interface, bulk, and surface roughness layer components and affects the CdS/CdTe heterojunction performance and the quantum efficiency of the solar cell in the blue region of the solar spectrum. Similarly, analysis of RTSE data collected during co-evaporation of Cu(In{sub 1−x}Ga{sub x})Se{sub 2} (CIGS; x ∼ 0.3) on a rough Mo back contact provides the evolution of a second phase of Cu{sub 2−x}Se within the CIGS layer. During the last stage of CIGS deposition, the In, Ga, and Se co-evaporants convert this Cu{sub 2−x}Se phase to CIGS, and RTSE identifies the endpoint, specifically the time at which complete conversion occurs and single-phase, large-grain CIGS is obtained in this key stage. - Highlights: • Real time spectroscopic ellipsometry (RTSE) study of CdS and CuIn{sub 1−x}Ga{sub x}Se{sub 2} (CIGS) films. • RTSE during CdS deposition provides the evolution of the CdS effective thickness. • RTSE for CIGS film enables to measure and control the composition and thickness. • The work leads to the development of optical models for processing steps.

An investigation on preparation of CIGS targets by sintering process

Energy Technology Data Exchange (ETDEWEB)

Zhang Ning, E-mail: zhn98@126.co [Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China); Zhuang Daming; Zhang Gong [Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

2010-01-15

Pressureless sintering process was used to fabricate CIGS targets with Cu{sub 2}Se, In{sub 2}Se{sub 3}, and Ga{sub 2}Se{sub 3} as raw powders mixed according to the stoichiometry of CuIn{sub 0.72}Ga{sub 0.28}Se{sub 2} (CIGS). The results showed that only CuIn{sub 0.7}Ga{sub 0.3}Se{sub 2} phase can be detected in the sintered targets. The pores in sintered specimen become smaller and distribute more homogeneously under the conditions of finer powders and higher cold pressure. Both mass loss caused by the formation of volatile phase relating to Ga and volume expansion occur during the sintering process, which result in the decrease of density. The tendency of anti-densification becomes stronger under the conditions of coarser powders and higher cold pressure. The sintering process and causes for anti-densification were discussed. Finally, a hot pressing process was carried out, which was proved to be fairly effective to increase the density of CIGS target. The fabricated target can be used for magnetron-sputtering deposition of CIGS absorbers.

Scale-up issues of CIGS thin film PV modules

Energy Technology Data Exchange (ETDEWEB)

Dhere, Neelkanth G. [Florida Solar Energy Center, 1679 Clearlake Road, Cocoa, FL 32922 (United States)

2011-01-15

Photovoltaics cost has been declining following a 70% learning curve. Now the challenge is to bring down the cost of solar electricity to make it competitive with conventional sources within the next decade. In the long run, the module efficiencies tend to reach 80% of the champion cell efficiencies. Using a semiempirical methodology, it has been shown earlier that while the triple junction a-Si:H thin film technology is competitive, CIGS and CdTe thin film module technologies are highly competitive and presently offer the best approach for significantly exceeding the cost/performance levels of standard and non-standard crystalline Si PV technologies. Since 2006, the production of thin film solar cell in the U.S. has surpassed that of c-Si. At present, the production of CIGS PV modules lags considerably behind that of CdTe PV modules. This is mainly because of its complexity. Scale-up issues related to various CIGS preparation technologies such as co-evaporation, metallic precursor deposition by magnetron sputtering and non-vacuum techniques such as ink-jet printing, electroplating or doctor-blade technology followed by their selenization/sulfurization are discussed so as to assist the CIGS technology to attain its full potential. Besides the welcome announcements of large volume production, it is essential to achieve the production cost below $1/Wp in the near term and attain production speeds comparable to CdTe production speeds. Comparable production speeds are expected to be achieved within the next decade. This will enable reduction of CIGS module production costs to {proportional_to}65 cents /Wp that would be comparable to the CdTe module projected production cost. Additionally CIGS will have a higher efficiency premium. (author)

Real Time Spectroscopic Ellipsometry Analysis of First Stage CuIn1−xGaxSe2 Growth: Indium-Gallium Selenide Co-Evaporation

Directory of Open Access Journals (Sweden)

Puja Pradhan

2018-01-01

Full Text Available Real time spectroscopic ellipsometry (RTSE has been applied for in-situ monitoring of the first stage of copper indium-gallium diselenide (CIGS thin film deposition by the three-stage co-evaporation process used for fabrication of high efficiency thin film photovoltaic (PV devices. The first stage entails the growth of indium-gallium selenide (In1−xGax2Se3 (IGS on a substrate of Mo-coated soda lime glass maintained at a temperature of 400 °C. This is a critical stage of CIGS deposition because a large fraction of the final film thickness is deposited, and as a result precise compositional control is desired in order to achieve the optimum performance of the resulting CIGS solar cell. RTSE is sensitive to monolayer level film growth processes and can provide accurate measurements of bulk and surface roughness layer thicknesses. These in turn enable accurate measurements of the bulk layer optical response in the form of the complex dielectric function ε = ε1 − iε2, spectra. Here, RTSE has been used to obtain the (ε1, ε2 spectra at the measurement temperature of 400 °C for IGS thin films of different Ga contents (x deduced from different ranges of accumulated bulk layer thickness during the deposition process. Applying an analytical expression in common for each of the (ε1, ε2 spectra of these IGS films, oscillator parameters have been obtained in the best fits and these parameters in turn have been fitted with polynomials in x. From the resulting database of polynomial coefficients, the (ε1, ε2 spectra can be generated for any composition of IGS from the single parameter, x. The results have served as an RTSE fingerprint for IGS composition and have provided further structural information beyond simply thicknesses, for example information related to film density and grain size. The deduced IGS structural evolution and the (ε1, ε2 spectra have been interpreted as well in relation to observations from scanning electron microscopy, X

All-Nonvacuum-Processed CIGS Solar Cells Using Scalable Ag NWs/AZO-Based Transparent Electrodes.

Science.gov (United States)

Wang, Mingqing; Choy, Kwang-Leong

2016-07-06

With record cell efficiency of 21.7%, CIGS solar cells have demonstrated to be a very promising photovoltaic (PV) technology. However, their market penetration has been limited due to the inherent high cost of the cells. In this work, to lower the cost of CIGS solar cells, all nonvacuum-processed CIGS solar cells were designed and developed. CIGS absorber was prepared by the annealing of electrodeposited metallic layers in a chalcogen atmosphere. Nonvacuum-deposited Ag nanowires (NWs)/AZO transparent electrodes (TEs) with good transmittance (92.0% at 550 nm) and high conductivity (sheet resistance of 20 Ω/□) were used to replace the vacuum-sputtered window layer. Additional thermal treatment after device preparation was conducted at 220 °C for a few of minutes to improve both the value and the uniformity of the efficiency of CIGS pixel cell on 5 × 5 cm substrate. The best performance of the all-nonvacuum-fabricated CIGS solar cells showed an efficiency of 14.05% with Jsc of 34.82 mA/cm(2), Voc of 0.58 V, and FF of 69.60%, respectively, which is comparable with the efficiency of 14.45% of a reference cell using a sputtered window layer.

Experimental and theoretical investigations of structural and optical properties of CIGS thin films

Energy Technology Data Exchange (ETDEWEB)

Chandramohan, M., E-mail: chandramohan59@yahoo.co.in [Department of Physics, Park college of Engineering and Tecknology, Coimbatore-641 659 (India); Velumani, S., E-mail: vels64@yahoo.com [Centro de Investigacion y de Estudios Avanzados del I.P.N.(CINVESTAV), Av. Instituto Politecnico Nacional 2508 Col. San Pedro Zacatenco 07360, Mexico D.F (Mexico); Venkatachalam, T., E-mail: atvenkatachalam@yahoo.com [Department of Physics, Coimbatore Institute of Technology, Coimbatore-14. India (India)

2010-10-25

Experimental and theoretical studies of the structural and optical properties of Copper Indium Gallium diSelenide thin films have been performed. Thin films of CIGS were deposited on glass substrates by chemical bath deposition. From the XRD results of the films, it is found that the films are of chalcopyrite type structure. The lattice parameter were determined as a = 5.72 A and c = 11.462 A. The optical properties of the thin films were carried out with the help of spectrophotometer. First principles density functional theory calculations of the band structure, density of states and effective masses of electrons and holes of the CIGS crystals have been done by computer simulations. The experimental data and theoretically calculated data have demonstrated good agreement.

Electrodeposition route to synthesize cigs films – an economical way ...

African Journals Online (AJOL)

Electrodeposition route to synthesize cigs films – an economical way to harness solar energy. ... for solar cells, how the charge separation in this nano scale photovoltaic (PV) materials occurs which help in absorption of radiation, and the electro-deposition route, a low cost one, produces thin film solar cells are analyzed.

Degradation of CIGS solar cells

NARCIS (Netherlands)

Theelen, M.J.

2015-01-01

Large scale commercial introduction of CIGS photovoltaics (PV) requires modules with low costs, high efficiencies and long and predictable lifetimes. Unfortunately,knowledge about the lifetime of CIGS PV is limited, which is reflected in the results of field studies: degradation rates varying from

Numerical modelling of CIGS/CdS solar cell

Science.gov (United States)

Devi, Nisha; Aziz, Anver; Datta, Shouvik

2018-05-01

In this work, we design and analyze the Cu(In,Ga)Se2 (CIGS) solar cell using simulation software "Solar Cell Capacitance Simulator in One Dimension (SCAPS-1D)". The conventional CIGS solar cell uses various layers, like intrinsic ZnO/Aluminium doped ZnO as transparent oxide, antireflection layer MgF2, and electron back reflection (EBR) layer at CIGS/Mo interface for good power conversion efficiency. We replace this conventional model by a simple model which is easy to fabricate and also reduces the cost of this cell because of use of lesser materials. The new designed model of CIGS solar cell is ITO/CIGS/OVC/CdS/Metal contact, where OVC is ordered vacancy compound. From this simple structure, even at very low illumination we are getting good results. We simulate this CIGS solar cell model by varying various physical parameters of CIGS like thickness, carrier density, band gap and temperature.

Enhancement of the CIGS solar cell's efficiency by anti-reflection coating with teflon AF

Energy Technology Data Exchange (ETDEWEB)

Bae, Hong-Sub; Kim, Chan; Rhee, Il-Su [Kyungpook National University, Daegu (Korea, Republic of); Jo, Hyun-Jun; Kim, Dae-Hwan [Daegu Gyeongbuk Institute of Science and Technology, Daegu (Korea, Republic of); Hong, Sung-Wook [Daegu University, Gyeongsan (Korea, Republic of)

2014-11-15

An anti-reflection (AR) layer of Teflon AF was deposited on the front surface of a Cu(In,Ga)Se{sub 2} (CIGS) solar cell with a structure of grid/TCO/ZnO/CdS/Cu(In,Ga)Se{sub 2}/Mo/glass by using the spin coating method. This AR layer reduced the front-surface reflection, which resulted in high efficiency for the CIGS solar cell. The thickness of the Teflon AF layer was varied to determine the thickness that gave the highest transmittance of incident light into the active absorber of the CIGS solar cell. The optimum thickness of the Teflon AF layer was found to be 105 nm. CIGS solar cells with a Teflon AF layer of 105 nm were constructed, and their efficiencies were compared with those of solar cells without a Teflon AF layer. The average increase in the relative efficiency of the solar cells was 2.63% due to the inclusion of an anti-reflection layer of Teflon AF.

Mg-doped ZnO thin films deposited by the atomic layer chemical vapor deposition for the buffer layer of CIGS solar cell

Energy Technology Data Exchange (ETDEWEB)

Li, Zhao-Hui [Department of Electronics Engineering, Gachon University, Soojung-gu, Seongnam city 461-701, Gyunggi-do (Korea, Republic of); Center for Photovoltaic and Solar Energy, Shenzhen Institutes of Advanced Technology, Chinese Academy of Sciences, Shenzhen city 518055 (China); Cho, Eou-Sik [Department of Electronics Engineering, Gachon University, Soojung-gu, Seongnam city 461-701, Gyunggi-do (Korea, Republic of); Kwon, Sang Jik, E-mail: sjkwon@gachon.ac.kr [Department of Electronics Engineering, Gachon University, Soojung-gu, Seongnam city 461-701, Gyunggi-do (Korea, Republic of)

2014-09-30

Highlights: • Mg-doped ZnO film as CIGS buffer was prepared by ALD process. • The grain size of ZnO-like hexagonal phase decreased with Mg content. • The transmittance and crystallinity increased but the band gap decreased with temperature. - Abstract: Mg-doped ZnO [(Zn, Mg)O] thin films were prepared by atomic layer chemical vapor deposition (ALCVD) process with different Mg content, using diethyl zinc, biscyclopentadienyl magnesium, and water as the metal and oxygen sources, respectively. The ratio of Mg to Zn was varied by changing the pulse ratio of MgCp{sub 2} to DEZn precursor to study its effect on the properties of (Zn, Mg)O thin films. From the experimental results, it was shown that the grain size of the ZnO-like hexagonal phase (Zn, Mg)O decreased as the Mg content increased. But the transmittance and optical band gap of (Zn, Mg)O films increased with the increase of the Mg content. In addition, the effect of the substrate temperature on the properties of (Zn, Mg)O films was also investigated. The deposition rate, transmittance, and crystallinity of (Zn, Mg)O films increased as the substrate temperature increased. But its band gap decreased slightly with the increase of substrate temperature.

In Situ and Ex Situ Studies of Molybdenum Thin Films Deposited by rf and dc Magnetron Sputtering as a Back Contact for CIGS Solar Cells

Directory of Open Access Journals (Sweden)

K. Aryal

2012-01-01

Full Text Available Molybdenum thin films were deposited by rf and dc magnetron sputtering and their properties analyzed with regards to their potential application as a back contact for CIGS solar cells. It is shown that both types of films tend to transition from tensile to compressive strain when the deposition pressure increases, while the conductivity and the grain size decreas. The nucleation of the films characterized by in situ and real time spectroscopic ellipsometry shows that both films follow a Volmer-Weber growth, with a higher surface roughness and lower deposition rate for the rf deposited films. The electronic relaxation time was then extracted as a function of bulk layer thickness for rf and dc films by fitting each dielectric function to a Drude free-electron model combined with a broad Lorentz oscillator. The values were fitted to a conical growth mode and demonstrated that the rf-deposited films have already smaller grains than the dc films when the bulk layer thickness is 30 nm.

Band gap engineering of tandem structured CIGS compound absorption layer fabricated by sputtering and selenization

International Nuclear Information System (INIS)

Kang, San; Sharma, Rahul; Sim, Jae-Kwan; Lee, Cheul-Ro

2013-01-01

Highlights: ► Systematic band gap engineering to fabricate tandem Cu(In,Ga)Se 2 absorption layers. ► XRD shows prominent (1 1 2) reflection shift for attributed CIS, CIGS, and CGS phases. ► Optical transmittance and reflectance spectrum are improved towards infrared region. ► The Cu/In + Ga and Ga/In + Ga effect is matched with highest efficient solar cell. ► Tandem CIS/CIGS/CGS layer, the band gap is increased from 1.15 to 2.06 eV. -- Abstract: Band gap engineering was executed to fabricate a multi-junction stacked i.e. tandem Cu(In,Ga)Se 2 (CIGS) absorption layer. The CIGS absorption layers consist of multi-junction stacked CIS/CIGS/CGS thin films from bottom to top with increasing band gap. Tandem CIGS layers were fabricated by using three precursor of CuIn, In/CuGa/In, and CuGa onto the Mo coated soda-lime glass (SLG) by the sequential sputtering of CuIn, CuGa, and In targets. The CIG precursors were converted into CIGS absorption thin film by selenization process. From the X-ray diffraction (XRD) pattern of CIS/CIGS/CGS tandem layer, with the prominent peak shift for (1 1 2) reflections was attributed to the individual CIS, CIGS, and CGS phases at 26.76°, 27.15°, and 27.65° diffraction angles, respectively. The morphologies and atomic (at%) composition uniformity onto the surface and along the depth were extensively analyzed with field effect scanning electron microscope (FESEM) attached energy dispersive spectroscopy (EDS) and secondary ion mass spectroscopy (SIMS). The optical properties such as transmittance, reflectance and absorbance were found to improve in the infrared region for all the tandem CIGS layers. Near the fundamental absorption edge, the absorption coefficient was approached to 10 5 cm −1 for CIS/CIGS/CGS tandem layer. The straight-line behavior indicates that the films have a direct band gap. The band gap was found to increase from 1.15 to 1.74 eV with the Ga-grading along the depth of individual CIS, CIGS, and CGS thin films

Improving Efficiency of Multicrystalline Silicon and CIGS Solar Cells by Incorporating Metal Nanoparticles

Directory of Open Access Journals (Sweden)

Ming-Jer Jeng

2015-10-01

Full Text Available This work studies the use of gold (Au and silver (Ag nanoparticles in multicrystalline silicon (mc-Si and copper-indium-gallium-diselenide (CIGS solar cells. Au and Ag nanoparticles are deposited by spin-coating method, which is a simple and low cost process. The random distribution of nanoparticles by spin coating broadens the resonance wavelength of the transmittance. This broadening favors solar cell applications. Metal shadowing competes with light scattering in a manner that varies with nanoparticle concentration. Experimental results reveal that the mc-Si solar cells that incorporate Au nanoparticles outperform those with Ag nanoparticles. The incorporation of suitable concentration of Au and Ag nanoparticles into mc-Si solar cells increases their efficiency enhancement by 5.6% and 4.8%, respectively. Incorporating Au and Ag nanoparticles into CIGS solar cells improve their efficiency enhancement by 1.2% and 1.4%, respectively. The enhancement of the photocurrent in mc-Si solar cells is lower than that in CIGS solar cells, owing to their different light scattering behaviors and material absorption coefficients.

Adhesion Improvement and Characterization of Magnetron Sputter Deposited Bilayer Molybdenum Thin Films for Rear Contact Application in CIGS Solar Cells

Directory of Open Access Journals (Sweden)

Weimin Li

2016-01-01

Full Text Available Molybdenum (Mo thin films are widely used as rear electrodes in copper indium gallium diselenide (CIGS solar cells. The challenge in Mo deposition by magnetron sputtering lies in simultaneously achieving good adhesion to the substrates while retaining the electrical and optical properties. Bilayer Mo films, comprising five different thickness ratios of a high pressure (HP deposited bottom layer and a low pressure (LP deposited top layer, were deposited on 40 cm × 30 cm soda-lime glass substrates by DC magnetron sputtering. We focus on understanding the effects of the individual layer properties on the resulting bilayer Mo films, such as microstructure, surface morphology, and surface oxidation. We show that the thickness of the bottom HP Mo layer plays a major role in determining the micromechanical and physical properties of the bilayer Mo stack. Our studies reveal that a thicker HP Mo bottom layer not only improves the adhesion of the bilayer Mo, but also helps to improve the film crystallinity along the preferred [110] direction. However, the surface roughness and the porosity of the bilayer Mo films are found to increase with increasing bottom layer thickness, which leads to lower optical reflectance and a higher probability for oxidation at the Mo surface.

Substrate temperature optimization for Cu(In, Ga)Se{sub 2} solar cells on flexible stainless steels

Energy Technology Data Exchange (ETDEWEB)

Liang, X.; Zhu, H.; Chen, J., E-mail: chenjingwei@126.com; Zhou, D.; Zhang, C.; Guo, Y.; Niu, X.; Li, Z.; Mai, Y., E-mail: yaohuamai@hbu.edu.cn

2016-04-15

Graphical abstract: - Highlights: • CIGS thin films are deposited on flexible SS substrates at different substrate temperatures. • CIGS thin films deposited at different T{sub S2} show different Ga/(Ga + In) ratio profiles. • All CIGS thin films show (112) and (220/204) preferred orientations with a shift to higher angles. • Conversion efficiency of 11.3% is obtained for CIGS solar cells deposited at 500 °C. - Abstract: Cu(In, Ga)Se{sub 2} (CIGS) thin films are deposited on flexible stainless steel (SS) substrates using the so called 3-stage co-evaporation process at different substrate temperatures ranging from 440 °C to 640 °C during the 2nd stage and the 3rd stage (T{sub S2}). The effects of T{sub S2} on the properties of CIGS thin films are systematically investigated. It is found by secondary ion mass spectrometry measurement that CIGS thin films deposited at different T{sub S2} show different Ga/(Ga + In) ratio (GGI) profiles along the growth direction. High T{sub S2} facilitates the grain growth and leads to larger grain size. However, high T{sub S2} worsens the spectral response of CIGS solar cells in the long wavelength range, which is partly attributed to the too much iron atom diffusion from the SS substrates into the CIGS thin films. All CIGS thin films show (112) preferred orientations with a shift to higher angle due to variation of compositions. A shoulder-like two-peak structure of (112) and (220/204) peaks appears for CIGS thin films deposited at lower T{sub S2}. Conversion efficiency of 11.3% is obtained for CIGS thin film solar cells deposited at the T{sub S2} of 500 °C.

Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (CuInSe2 based PV cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (CuInSe2 taiyo denchi seizo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on the fabrication technology of CuInSe2 based PV cell in fiscal 1994. (1) On formation of high-quality CIGS thin films by bilayer method, Mo film was deposited on a glass substrate by sputtering, and CIGS film with different Ga/In ratios was next formed on the substrate by quaternary simultaneous deposition at different In and Ga deposition speeds. In addition, CdS film was deposited on the CIGS film, and ZnO and ITO films were finally deposited on it by sputtering to complete solar cell. This solar cell offered the maximum conversion efficiency among cells using CIGS film. (2) On formation of high-quality CIGS thin films by three-stage method, a certain correlation was found between substrate temperature and CIGS film composition by monitoring substrate temperature in film forming process. This phenomenon allowed rigorous control of CIS film compositions important for CIS thin film solar cells. (3) On low-cost process technology for thin film formation, Cu(In,Ga)S2 solid solution film was fabricated by expanded selenic process. 3 figs.

Band gap engineering of tandem structured CIGS compound absorption layer fabricated by sputtering and selenization

Energy Technology Data Exchange (ETDEWEB)

Kang, San; Sharma, Rahul; Sim, Jae-Kwan [Semiconductor Materials Processing Laboratory, School of Advanced Materials Engineering, College of Engineering, Research Center for Advanced Materials Development (RCAMD), Chonbuk National University, Deokjin-dong 664-14, Jeonju 561-756 (Korea, Republic of); Lee, Cheul-Ro, E-mail: crlee7@jbnu.ac.kr [Semiconductor Materials Processing Laboratory, School of Advanced Materials Engineering, College of Engineering, Research Center for Advanced Materials Development (RCAMD), Chonbuk National University, Deokjin-dong 664-14, Jeonju 561-756 (Korea, Republic of)

2013-06-25

Highlights: ► Systematic band gap engineering to fabricate tandem Cu(In,Ga)Se{sub 2} absorption layers. ► XRD shows prominent (1 1 2) reflection shift for attributed CIS, CIGS, and CGS phases. ► Optical transmittance and reflectance spectrum are improved towards infrared region. ► The Cu/In + Ga and Ga/In + Ga effect is matched with highest efficient solar cell. ► Tandem CIS/CIGS/CGS layer, the band gap is increased from 1.15 to 2.06 eV. -- Abstract: Band gap engineering was executed to fabricate a multi-junction stacked i.e. tandem Cu(In,Ga)Se{sub 2} (CIGS) absorption layer. The CIGS absorption layers consist of multi-junction stacked CIS/CIGS/CGS thin films from bottom to top with increasing band gap. Tandem CIGS layers were fabricated by using three precursor of CuIn, In/CuGa/In, and CuGa onto the Mo coated soda-lime glass (SLG) by the sequential sputtering of CuIn, CuGa, and In targets. The CIG precursors were converted into CIGS absorption thin film by selenization process. From the X-ray diffraction (XRD) pattern of CIS/CIGS/CGS tandem layer, with the prominent peak shift for (1 1 2) reflections was attributed to the individual CIS, CIGS, and CGS phases at 26.76°, 27.15°, and 27.65° diffraction angles, respectively. The morphologies and atomic (at%) composition uniformity onto the surface and along the depth were extensively analyzed with field effect scanning electron microscope (FESEM) attached energy dispersive spectroscopy (EDS) and secondary ion mass spectroscopy (SIMS). The optical properties such as transmittance, reflectance and absorbance were found to improve in the infrared region for all the tandem CIGS layers. Near the fundamental absorption edge, the absorption coefficient was approached to 10{sup 5} cm{sup −1} for CIS/CIGS/CGS tandem layer. The straight-line behavior indicates that the films have a direct band gap. The band gap was found to increase from 1.15 to 1.74 eV with the Ga-grading along the depth of individual CIS, CIGS

Development of Enhanced Window layers for CIGS Photovoltaic Devices

Science.gov (United States)

Alexander, J. Nicholas

One of the most promising thin film devices right now is the Copper Indium Gallium Selenide (CIGS) solar cell with maximum reported power conversion efficiency of 22.3%. The Transparent Conducting Oxide (TCO) which is the top layer of the CIGS device also known as the window layer, is responsible for collecting the electrons generated in the CIGS device and conducting them to the circuit. Development of a very low resistivity film with a high optical transmission is crucial for optimal performance of devices as well as the ability to be deployed without changes to their properties for several decades. Current TCOs such as indium tin oxide (ITO) and aluminum doped zinc oxide (AZO) are met with limitations with either using large amounts of expensive materials such as indium, often requiring and anneal step to obtain good conductivity, or have shown poor long term reliability. This thesis is focused on development of InZnO and zirconium doped InZnO as a potential replacement TCO to obtain high conductivity and high transmission like the leading TCOs without needing heated depositions, post deposition annealing, and maintain a good film reliability. Zirconium doping was employed to farther enhance both the optical and electrical properties through enhancement of the films high frequency permittivity of InZnO while providing improved reliability to the film. The films were grown through a mix of DC and RF co-sputtering. InZnO films were deposited at varying indium concentration ( 10-30%) and samples were able to achieve low resistivity ( 7x10-4 O-cm), high mobility (>30 cm2/v.s), high carrier concentration (>10 20 cm-3), while maintaining high transmission (> 80%) in the visible and near-infrared region. After zirconium was incorporated into the InZnO films by replacement of the ZnO target with a ZrO2/ZnO (5:95) target, films of Zr:InZnO were deposit through the same method to achieve films that maintained very similar electrical and optical properties. The little

Nanosecond laser scribing of CIGS thin film solar cell based on ITO bottom contact

Science.gov (United States)

Kuk, Seungkuk; Wang, Zhen; Fu, Shi; Zhang, Tao; Yu, Yi Yin; Choi, JaeMyung; Jeong, Jeung-hyun; Hwang, David J.

2018-03-01

Cu(In,Ga)Se2 (CIGS) thin films, a promising photovoltaic architecture, have mainly relied on Molybdenum for the bottom contact. However, the opaque nature of Molybdenum (Mo) poses limitations in module level fabrication by laser scribing as a preferred method for interconnect. We examined the P1, P2, and P3 laser scribing processes on CIGS photovoltaic architecture on the indium tin oxide (ITO) bottom contact with a cost-effective nanosecond pulsed laser of 532 nm wavelength. Laser illuminated from the substrate side, enabled by the transparent bottom contact, facilitated selective laser energy deposition onto relevant interfaces towards high-quality scribing. Parametric tuning procedures are described in conjunction with experimental and numerical investigation of relevant mechanisms, and preliminary mini-module fabrication results are also presented.

Reducing interface recombination for Cu(In,Ga)Se{sub 2} by atomic layer deposited buffer layers

Energy Technology Data Exchange (ETDEWEB)

Hultqvist, Adam; Bent, Stacey F. [Department of Chemical Engineering, Stanford University, Stanford, California 94305 (United States); Li, Jian V.; Kuciauskas, Darius; Dippo, Patricia; Contreras, Miguel A.; Levi, Dean H. [National Renewable Energy Laboratory, Golden, Colorado 80401 (United States)

2015-07-20

Partial CuInGaSe{sub 2} (CIGS) solar cell stacks with different atomic layer deposited buffer layers and pretreatments were analyzed by photoluminescence (PL) and capacitance voltage (CV) measurements to investigate the buffer layer/CIGS interface. Atomic layer deposited ZnS, ZnO, and SnO{sub x} buffer layers were compared with chemical bath deposited CdS buffer layers. Band bending, charge density, and interface state density were extracted from the CV measurement using an analysis technique new to CIGS. The surface recombination velocity calculated from the density of interface traps for a ZnS/CIGS stack shows a remarkably low value of 810 cm/s, approaching the range of single crystalline II–VI systems. Both the PL spectra and its lifetime depend on the buffer layer; thus, these measurements are not only sensitive to the absorber but also to the absorber/buffer layer system. Pretreatment of the CIGS prior to the buffer layer deposition plays a significant role on the electrical properties for the same buffer layer/CIGS stack, further illuminating the importance of good interface formation. Finally, ZnS is found to be the best performing buffer layer in this study, especially if the CIGS surface is pretreated with potassium cyanide.

CIGS thin film solar cell prepared by reactive co-sputtering

Science.gov (United States)

Kim, Jeha; Lee, Ho-Sub; Park, Nae-Man

2013-09-01

The reactive co-sputtering was developed as a new way of preparing high quality CuInGaSe2(CIGS) films from two sets of targets; Cu0.6Ga 0.4 and Cu0.4In0.6 alloy and Cu and (In0.7Ga0.3)2Se3 compound targets. During sputtering, Cu, In, Ga metallic elements as well as the compound materials were reacted to form CIGS simultaneously in highly reactive elemental Se atmosphere generated by a thermal cracker. CIGS layer had been grown on Mo/soda-lime glass(SLG) at 500°C. For both sets of targets, we controlled the composition of CIGS thin film by changing the RF power for target components. All the films showed a preferential (112) orientation as observed from X-ray diffraction analysis. The composition ratios of CIGS were easily set to 0.71-0.95, 0.10-0.30 for [Cu]/[III] and [Ga]/[III], respectively. The grain size and the surface roughness of a CIGS film increased as the [Cu]/[III] ratios increased. The solar cells were fabricated using a standard base line process in the device structure of grid/ITO/i-ZnO/CdS/CIGS/Mo/ SLG. The best performance was obtained the performance of Voc = 0.45 V, Jsc =35.6, FF = 0.535, η = 8.6% with a 0.9 μm-CIGS solar cell from alloy targets while Voc = 0.54 V, Jsc =30.8, FF = 0.509, η = 8.5% with a 0.8 μm-CIGS solar cell from Cu and (In0.7Ga0.3)2Se3.

CIGS J-V distortion in the absence of blue photons

International Nuclear Information System (INIS)

Pudov, A.O.; Sites, J.R.; Contreras, M.A.; Nakada, T.; Schock, H.-W.

2005-01-01

Common buffer materials used with CuInGaSe 2 (CIGS) absorbers produce conduction-band barriers that may significantly distort the current-voltage (J-V) curves, especially when short-wavelength photons are excluded from the illumination spectrum. Earlier work documented this effect for CuInSe 2 (CIS) absorbers (band gap near 1.0 eV) with CdS buffers. Higher band-gap (no. approxno. 1.15 eV) CIGS absorbers show little or no distortion with CdS buffer layers. However, wider band gap (lower electron affinity) ZnS(O,OH) or InS(O,OH) buffers, prepared by chemical-bath deposition (CBD), clearly show the J-V distortion. The distortions have a turn-on time constant the order of a minute and turn-off time constant the order of a day, and they correlate with major variations in apparent quantum efficiency (QE) measured with varying intensity and spectral content of bias light. The results are consistent with a conduction-band spike barrier that increases with buffer band gap and is larger when the electron concentration in the buffer is small

Electrical properties of aluminum contacts deposited by DC sputtering method for photovoltaic applications

Directory of Open Access Journals (Sweden)

Krawczak Ewelina

2017-01-01

Full Text Available The use of aluminum contacts is common in the process of silicon solar cells production because of low contact resistivity. It has also a great importance in thin film technology for photovoltaics, especially in copper-indium-gallium-diselenide (CIGS devices. The final stage of CIGS cell production is the top contact deposition of high conductivity layer for lateral current collection. Such material has to be highly optically transparent as well. In order to make a contact, metal is deposited onto TCO layer with minimum shadowing to allow as much light as possible into device. The metal grid contact is being made by deposition of few microns of aluminum. The resistivity of the deposited material as well as resistance between the metal grid and TCO layer plays a great role in high quality solar cell production. This paper presents the results of four point probe conductivity analysis of Al thin films deposited by direct current (DC magnetron sputtering method. Influence of technological parameters of the Al deposition process on sheet resistance of deposited layers has been showed. In order to obtain the lowest resistivity of the thin contact layer, optimal set of sputtering parameters, i.e. power applied, deposition time and deposition pressure was found. The resistivity of the contact between two adjacent Al metal fingers deposited onto transparent conductive Al-doped zinc oxide film has been also examined.

Electrical properties of aluminum contacts deposited by DC sputtering method for photovoltaic applications

Science.gov (United States)

Krawczak, Ewelina; Gułkowski, Sławomir

2017-10-01

The use of aluminum contacts is common in the process of silicon solar cells production because of low contact resistivity. It has also a great importance in thin film technology for photovoltaics, especially in copper-indium-gallium-diselenide (CIGS) devices. The final stage of CIGS cell production is the top contact deposition of high conductivity layer for lateral current collection. Such material has to be highly optically transparent as well. In order to make a contact, metal is deposited onto TCO layer with minimum shadowing to allow as much light as possible into device. The metal grid contact is being made by deposition of few microns of aluminum. The resistivity of the deposited material as well as resistance between the metal grid and TCO layer plays a great role in high quality solar cell production. This paper presents the results of four point probe conductivity analysis of Al thin films deposited by direct current (DC) magnetron sputtering method. Influence of technological parameters of the Al deposition process on sheet resistance of deposited layers has been showed. In order to obtain the lowest resistivity of the thin contact layer, optimal set of sputtering parameters, i.e. power applied, deposition time and deposition pressure was found. The resistivity of the contact between two adjacent Al metal fingers deposited onto transparent conductive Al-doped zinc oxide film has been also examined.

A high-efficiency solution-deposited thin-film photovoltaic device

Energy Technology Data Exchange (ETDEWEB)

Mitzi, David B; Yuan, Min; Liu, Wei; Chey, S Jay; Schrott, Alex G [IBM T. J. Watson Research Center, Yorktown Heights, NY (United States); Kellock, Andrew J; Deline, Vaughn [IBM Almaden Research Center, San Jose, CA (United States)

2008-10-02

High-quality Cu(In,Ga)Se{sub 2} (CIGS) films are deposited from hydrazine-based solutions and are employed as absorber layers in thin-film photovoltaic devices. The CIGS films exhibit tunable stoichiometry and well-formed grain structure without requiring post-deposition high-temperature selenium treatment. Devices based on these films offer power conversion efficiencies of 10% (AM1.5 illumination). (Abstract Copyright [2008], Wiley Periodicals, Inc.)

Effector Protein Cig2 Decreases Host Tolerance of Infection by Directing Constitutive Fusion of Autophagosomes with the Coxiella-Containing Vacuole

Directory of Open Access Journals (Sweden)

Lara J. Kohler

2016-07-01

Full Text Available Coxiella burnetii replicates in an acidified lysosome-derived vacuole. Biogenesis of the Coxiella-containing vacuole (CCV requires bacterial effector proteins delivered into host cells by the Dot/Icm secretion system. Genetic and cell biological analysis revealed that an effector protein called Cig2 promotes constitutive fusion of autophagosomes with the CCV to maintain this compartment in an autolysosomal stage of maturation. This distinguishes the CCV from other pathogen-containing vacuoles that are targeted by the host autophagy pathway, which typically confers host resistance to infection by delivering the pathogen to a toxic lysosomal environment. By maintaining the CCV in an autolysosomal stage of maturation, Cig2 enabled CCV homotypic fusion and enhanced bacterial virulence in the Galleria mellonella (wax moth model of infection by a mechanism that decreases host tolerance. Thus, C. burnetii residence in an autolysosomal organelle alters host tolerance of infection, which indicates that Cig2-dependent manipulation of a lysosome-derived vacuole influences the host response to infection.

7 CFR 1466.27 - Conservation Innovation Grants (CIG).

Science.gov (United States)

2010-01-01

..., evaluation, and implementation of: (i) Conservation adoption incentive systems, including market-based... 7 Agriculture 10 2010-01-01 2010-01-01 false Conservation Innovation Grants (CIG). 1466.27 Section... PROGRAM Contracts and Payments § 1466.27 Conservation Innovation Grants (CIG). (a) Definitions. In...

Metal-assisted chemical etching of CIGS thin films for grain size analysis

Energy Technology Data Exchange (ETDEWEB)

Xue, Chaowei [Research and Development Centre, Hanergy Thin Film Power Group Limited, Chengdu (China); Loi, Huu-Ha; Duong, Anh; Parker, Magdalena [Failure Analysis Department, MiaSole Hi-Tech Corp., Santa Clara, CA (United States)

2016-09-15

Grain size of the CIGS absorber is an important monitoring factor in the CIGS solar cell manufacturing. Electron backscatter diffraction (EBSD) analysis is commonly used to perform CIGS grain size analysis in the scanning electron microscope (SEM). Although direct quantification on SEM image using the average grain intercept (AGI) method is faster and simpler than EBSD, it is hardly applicable on CIGS thin films. The challenge is that, not like polycrystalline silicon, to define grain boundaries by selective chemical etching is not easily realizable for the multi-component CIGS alloy. In this Letter, we present direct quantification of CIGS thin film grain size using the AGI method by developing metal-assisted wet chemical etching process to define CIGS grain boundaries. The calculated value is similar to EBSD result. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

E-Cigs, Menthol & Dip

Science.gov (United States)

... Close Search × MENU BACK CLOSE SMOKEFREE.GOV HOME E-Cigs, Menthol & Dip There are many types of tobacco products. Learn how e-cigarettes, menthol cigarettes, smokeless tobacco, and other products ...

Design and long-term monitoring of DSC/CIGS tandem solar module

International Nuclear Information System (INIS)

Vildanova, M F; Nikolskaia, A B; Kozlov, S S; Shevaleevskiy, O I

2015-01-01

This paper describes the design and development of tandem dye-sensitized/Cu(In, Ga)Se (DSC/CIGS) PV modules. The tandem PV module comprised of the top DSC module and a bottom commercial 0,8 m 2 CIGS module. The top DSC module was made of 10 DSC mini-modules with the field size of 20 × 20 cm 2 each. Tandem DSC/CIGS PV modules were used for providing the long-term monitoring of energy yield and electrical parameters in comparison with standalone CIGS modules under outdoor conditions. The outdoor test facility, containing solar modules of both types and a measurement unit, was located on the roof of the Institute of Biochemical Physics in Moscow. The data obtained during monitoring within the 2014 year period has shown the advantages of the designed tandem DSC/CIGS PV-modules over the conventional CIGS modules, especially for cloudy weather and low-intensity irradiation conditions. (paper)

E-Cigs, Menthol & Dip

Science.gov (United States)

... are many types of tobacco products. Learn how e-cigarettes, menthol cigarettes, smokeless tobacco, and other products are ... your health. What We Know About Electronic Cigarettes (E-cigarettes) Some people use e-cigs to quit smoking. ...

2D Finite Element Model of a CIGS Module

Energy Technology Data Exchange (ETDEWEB)

Janssen, G.J.M.; Slooff, L.H.; Bende, E.E. [ECN Solar Energy, P.O.Box 1, NL-1755 ZG Petten (Netherlands)

2012-06-15

The performance of thin-film CIGS (Copper indium gallium selenide) modules is often limited due to inhomogeneities in CIGS layers. A 2-dimensional Finite Element Model for CIGS modules is presented that predicts the impact of such inhomogeneities on the module performance. Results are presented of a module with a region of poor diode characteristics. It is concluded that according to this model the effects of poor diodes depend strongly on their location in the module and on their dispersion over the module surface. Due to its generic character the model can also be applied to other series connections of photovoltaic cells.

2D - Finite element model of a CIGS module

Energy Technology Data Exchange (ETDEWEB)

Janssen, G.J.M.; Slooff, L.H.; Bende, E.E. [ECN Solar Energy, Petten (Netherlands)

2012-09-15

The performance of thin-film CIGS modules is often limited due to inhomogeneities in CIGS layers. A 2-dimensional Finite Element Model for CIGS modules is demonstrated that predicts the impact of such inhomogeneities on the module performance. Results are presented of a module with a region of poor diode characteristics. It is concluded that according to this model the effects of poor diodes depend strongly on their location in the module and on their dispersion over the module surface. Due to its generic character the model can also be applied to other series connections of photovoltaic cells.

BADANIA NAD TECHNOLOGIĄ OTRZYMYWANIA CIENKICH WARSTW EMITERA METODĄ ROZPYLANIA MAGNETRONOWEGO DLA ZASTOSOWAŃ W OGNIWACH CIGS

Directory of Open Access Journals (Sweden)

Justyna PIETRASZEK

Full Text Available Cienkowarstwowe ogniwa fotowoltaiczne wykonane na bazie struktury CIGS (mieszaniny pierwiastków miedzi, indu, galu oraz selenu należą do II generacji ogniw fotowoltaicznych. Wykazują one efektywność na poziomie zbliżonym do ogniw I generacji, lecz ze względu na niższe zużycie materiału, coraz częściej wypierają z rynku ogniwa krzemowe Artykuł przedstawia rezultaty badań dotyczących sposobu otrzymywania warstwy buforowej CdS (siarczku kadmu, zastosowanej w cienkowarstwowych ogniwach fotowoltaicznych typu CIGS. Przyjęto dwa rozwiązania technologii nanoszenia: warstwa okna CdS uzyskana metodą rozpylenia magnetronowego oraz warstwa okna CdS uzyskana metodą kąpieli chemicznej (CBD– Chemical Bath Deposition. Struktura ta powinna posiadać odpowiednią wielkość przerwy energetycznej, która pozwali na większą absorpcję fotonów, a także wymaga się, aby była cienka (mniej niż 100 nm i jednolita. Warstwy CdS zostały nałożone przez osadzanie w kąpieli chemicznej CBD na szklanych podłożach pokrytych Mo/CIGS (naniesione warstwy metodą sputteringu magnetronowego. Uzyskano dzięki temu warstwę emitera o grubości 80 nm po czasie osadzania 35 minut. Dla porównania warstwy CdS zostały nałożone poprzez sputtering magnetronowy na podłożu Mo/CIGS, uzyskanym tą samą metodą. Następnie oba rozwiązania zostały przebadane pod względem morfologii powierzchni na elektronowym mikroskopie skaningowym, jak również przeprowadzono analizy składu pierwiastkowego warstw. Zarówno jedna, jak i druga metoda prowadzi do otrzymania warstwy emitera CdS dla zastosowań w ogniwach CIGS.

Optical characteristics of thin CIGS cells on TCO back contact

NARCIS (Netherlands)

Deelen, J. van; Kniknie, B.; Vroon, Z.A.E.P.; Wuerz, R.; Kessler, F.

2014-01-01

Reduction of CIGS layer thickness could translate in significant cost reduction. CIGS was made on transparent conductive oxide (TCO) to allow for optical characterization. This data was compared with external quantum efficiency (EQE) data. The results suggest that changes in surface morphology are

Photoluminescence of Cu(In,Ga)Se2 in the solar cell preparation process

International Nuclear Information System (INIS)

Sho, Shirakata; Shinji, Yudate; Jyunji, Honda; Naoki, Iwado

2010-01-01

Full text : Sequential step by step photoluminescence (PL) measurements have been carried out on Cu(In,Ga)Se 2 (CIGS) films just after each thin-film processes for the fabrication of the CIGS solar cell. These include, (i) the CIGS film deposition on the Mo-coated soda-lime glass substrate by three-stage method (CIGS/Mo/SLG), (ii) the chemical-bath deposition (CBD) of CdS buffer layer, (iii) deposition of undoped ZnO window layer by RF sputtering, (iv) deposition of Al doped ZnO high-conductive window layer by RF sputtering, (v) Al grid electrode deposition for the CIGS solar cell, and (vi) the mechanical scribing for the electrical isolation of small test cells. Roomtemperature PL measurements have been done with the excitation of a He-Ne laser (632.8 nm, 1 mW) focused on the sample surface to 0.2 mm diameter. PL was dispersed by a polycromator (Horiba: MicroHR) and detected by a cooled InGaAs multichannel detector (1024 pixels). In order to study the uniformity of PL within CIGS films, the two dimensional PL spectrum mapping measurement has been done (0.4-0.6 mm step) using an x-y stage operating in the raster scanning mode. Acquisition time of one PL spectrum was 1 s. Once the fresh CIGS film is exposed to the air, intensity of the near-band-edge PL decreases slowly with time. After few days, PL intensity was one order of magnitude weaker than its initial value. Thus, PL measurement was performed just after the deposition. It was shown that PL spectra of CIGS films taken for each process in the CIGS solar cell preparation. PL of the CIGS film exhibited nearband-edge peak at 1.18 eV. The slight increase of PL intensity was observed after depositions of CdS and ZnO films. After the high conductive ZnO:Al deposition, PL intensity decreases to one third of the initial PL intensity of the fresh CIGS film. No change has been observed with respect to the line shape of PL peaks during the process. In the CIGS solar cell (open circuit condition), PL intensity recovers

Morphology and structure evolution of Cu(In,Ga)S{sub 2} films deposited by reactive magnetron co-sputtering with electron cyclotron resonance plasma assistance

Energy Technology Data Exchange (ETDEWEB)

Nie, Man, E-mail: man.nie@helmholtz-berlin.de; Ellmer, Klaus [Department of Solar Fuels and Energy Storage Materials, Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Hahn-Meitner-Platz 1, D14109 Berlin (Germany)

2014-02-28

Cu(In,Ga)S{sub 2} (CIGS) films were deposited on Mo coated soda lime glass substrates using an electron cyclotron resonance plasma enhanced one-step reactive magnetron co-sputtering process (ECR-RMS). The crystalline quality and the morphology of the Cu(In,Ga)S{sub 2} films were investigated by X-ray diffraction, atomic force microscopy, scanning electron microscopy, and X-ray fluorescence. We also compared these CIGS films with films previously prepared without ECR assistance and find that the crystallinity of the CIGS films is correlated with the roughness evolution during deposition. Atomic force microscopy was used to measure the surface topography and to derive one-dimensional power spectral densities (1DPSD). All 1DPSD spectra of CIGS films exhibit no characteristic peak which is typical for the scaling of a self-affine surface. The growth exponent β, characterizing the roughness R{sub q} evolution during the film growth as R{sub q} ∼ d{sup β}, changes with film thickness. The root-mean-square roughness at low temperatures increases only slightly with a growth exponent β = 0.013 in the initial growth stage, while R{sub q} increases with a much higher exponent β = 0.584 when the film thickness is larger than about 270 nm. Additionally, we found that the H{sub 2}S content of the sputtering atmosphere and the Cu- to-(In + Ga) ratio has a strong influence of the morphology of the CIGS films in this one-step ECR-RMS process.

Vaping cannabis (marijuana): parallel concerns to e-cigs?

OpenAIRE

Budney, Alan J.; Sargent, James D.; Lee, Dustin C.

2015-01-01

The proliferation of vaporization (‘vaping’) as a method for administering cannabis raises many of the same public health issues being debated and investigated in relation to e-cigarettes (e-cigs). Good epidemiological data on the prevalence of vaping cannabis are not yet available, but with current trends towards societal approval of medicinal and recreational use of cannabis, the pros and cons of vaping cannabis warrant study. As with e-cigs, vaping cannabis portends putative health benefit...

Breakthrough to Non-Vacuum Deposition of Single-Crystal, Ultra-Thin, Homogeneous Nanoparticle Layers: A Better Alternative to Chemical Bath Deposition and Atomic Layer Deposition

Directory of Open Access Journals (Sweden)

Yu-Kuang Liao

2017-04-01

Full Text Available Most thin-film techniques require a multiple vacuum process, and cannot produce high-coverage continuous thin films with the thickness of a few nanometers on rough surfaces. We present a new ”paradigm shift” non-vacuum process to deposit high-quality, ultra-thin, single-crystal layers of coalesced sulfide nanoparticles (NPs with controllable thickness down to a few nanometers, based on thermal decomposition. This provides high-coverage, homogeneous thickness, and large-area deposition over a rough surface, with little material loss or liquid chemical waste, and deposition rates of 10 nm/min. This technique can potentially replace conventional thin-film deposition methods, such as atomic layer deposition (ALD and chemical bath deposition (CBD as used by the Cu(In,GaSe2 (CIGS thin-film solar cell industry for decades. We demonstrate 32% improvement of CIGS thin-film solar cell efficiency in comparison to reference devices prepared by conventional CBD deposition method by depositing the ZnS NPs buffer layer using the new process. The new ZnS NPs layer allows reduction of an intrinsic ZnO layer, which can lead to severe shunt leakage in case of a CBD buffer layer. This leads to a 65% relative efficiency increase.

Parameters optimization of CIGS solar cell using 2D physical modeling

Directory of Open Access Journals (Sweden)

Samar Dabbabi

Full Text Available In this study, the CIGS thin film solar cell has been investigated using the two-dimensional device simulator Silvaco-Atlas. Thickness and carrier concentration effects of the cell structure were studied to optimize the solar cell performances. Our results revealed high efficiency for a cell structure of 0.15 µm ZnO:Al, 0.06 µm i-ZnO, 0.04 µm CdS and 3 µm CIGS. The carrier concentration effects of the different layers were also studied revealing a better performance for CIGS doping concentration of 1018 cm−3. The optimized CIGS solar cell characteristics were a current density of short circuit Jsc = 38.75 mA/cm2, an open-circuit voltage V0C = 804.03 mV, a fill factor FF = 74.48% and an efficiency η = 23.20%. This result is in good agreement with experimental efficiencies found in literature. Keywords: CIGS solar cell, Electrical characteristics, Silvaco-Atlas software

Effect of yoghurt or yoghurt serum on microbial quality of cig kofte.

Science.gov (United States)

Dogan, Mahmut; Cankurt, Hasan; Toker, Omer Said; Yetim, Hasan; Sagdic, Osman

2014-07-01

Cig kofte, raw meatball is a traditionally produced meat product in Turkey and some other Middle East countries. It is prepared from mixtures of finely minced raw beef, bulgur, onions, various spices and tap water. Cig kofte is an uncooked product and popularly consumed with lettuce and lemon juice. In this study, yoghurt or yoghurt serum (YS) were added to the mixtures of cig kofte instead of tap water to reduce microbial risks of the raw meatball. Additionally, the effects of yoghurt and YS on some physicochemical characteristics of cig kofte were investigated. Cig kofte is generally consumed within a few hours after the preparation because of its raw nature. Also, it is generally sold under unhygienic conditions in restaurants and restaurant-like places. For this purpose, reducing of the microbial load of cig kofte is important. In the results, Escherichia coli and Listeria monocytogenes were not detected in any samples. While lactic acid bacteria count increased by addition of yoghurt and YS, the number of other microorganisms except for total aerobic mesophilic bacteria (TAMB) were decreased. The aw values and% moisture contents of the samples were varied between 0.88-0.94 and 46.25-49.72, respectively. The pH values of the samples were slightly changed during the storage of 24 h while no changes detected in the control samples during the storage. In conclusion, it can be suggested that using the yoghurt or YS instead of tap water in the preparation of cig kofte might ensure the microbial safety, increase the nutritional value and its flavour or aroma.

Parameters optimization of CIGS solar cell using 2D physical modeling

Science.gov (United States)

Dabbabi, Samar; Nasr, Tarek Ben; Kamoun-Turki, Najoua

In this study, the CIGS thin film solar cell has been investigated using the two-dimensional device simulator Silvaco-Atlas. Thickness and carrier concentration effects of the cell structure were studied to optimize the solar cell performances. Our results revealed high efficiency for a cell structure of 0.15 μm ZnO:Al, 0.06 μm i-ZnO, 0.04 μm CdS and 3 μm CIGS. The carrier concentration effects of the different layers were also studied revealing a better performance for CIGS doping concentration of 1018 cm-3. The optimized CIGS solar cell characteristics were a current density of short circuit Jsc = 38.75 mA/cm2, an open-circuit voltage V0C = 804.03 mV, a fill factor FF = 74.48% and an efficiency η = 23.20%. This result is in good agreement with experimental efficiencies found in literature.

Preparation and optimization of a molybdenum electrode for CIGS solar cells

Directory of Open Access Journals (Sweden)

Feng Jingxue

2016-11-01

Full Text Available Molybdenum (Mo films were deposited by radio frequency (RF, direct current (DC and mixed magnetron sputtering, respectively. With changing the deposition parameters including deposition pressure and power, the films show different surface morphology and crystallinity. Lower resistivity of the films is obtained in the DC mode and better reflectivity of the films is obtained in the RF mode. It is shown that the crystallinity increases when the deposition pressure decreases. The crystallinity and the grain size both increase as the deposition power increasing. The lowest resistivity of the single Mo film is 34×10-6 Ω·cm when the deposition pressure is 0.1 Pa and the deposition power is 300 W in the DC mode. In order to obtain lower resistivity, better adhesion and better reflectivity, bilayer films and tri-layer films were both deposited in different mode. They all show good adhesion and low resistivity. The Mo films deposited in mixed mode show better reflectivity. It is demonstrated that the resistivity of about 65×10-6 Ω·cm is achieved in DC/RF mode and the resistivity of about 61×10-6 Ω·cm is achieved in RF/DC/RF mode. And the tri-layer films achieved in RF/DC/RF mode have better reflectivity than bilayer films achieved in DC/RF mode. The tri-layer films achieved in RF/DC/RF mode is appropriate for using as the electrode of CIGS solar cells.

TEMPERATUREEFFECT OFELECTRICALPROPERTIES OF CIGS SOLAR CELL

Directory of Open Access Journals (Sweden)

A. M. Ferouani

2015-07-01

Full Text Available In this paper we are interested in studying the copper–indium–gallium–selenium (CIGS solar cells sandwiched between cadmium sulfide (CdS and ZnO as buffer layers, and Molybdenum (Mo. Thus, we report our simulation results using the capacitance simulator (SCAPS in terms of layer thickness, absorber layer band gap and operating temperature to find out the optimum choice. An efficiency of 20.61% (with Voc of 635.2mV, Jsc of 44.08 mA/cm2 and fill factor of 0.73 has been achieved with CdS used as buffer layer as the reference case. It is also found that the high efficiency CIGS cells with the low temperature were a very high efficiency conversion.

Degradation of CIGS solar cells

NARCIS (Netherlands)

Theelen, M.J.

2015-01-01

Thin film CIGS solar cells and individual layers within these solar cells have been tested in order to assess their long term stability. Alongside with the execution of standard tests, in which elevated temperatures and humidity levels are used, the solar cells have also been exposed to a

Reusing a declarative specification to check the conformance of different CIGs

NARCIS (Netherlands)

Grando, M.A.; Aalst, van der W.M.P.; Mans, R.S.; Daniel, F.; Barkaoui, K.; Dustdar, S.

2012-01-01

Several Computer Interpretable Guidelines (CIGs) languages have been proposed by the health community. Even though these CIG languages share common ideas each language has to be provided with his own mechanism of verification. In an earlier work we have shown that a DECLARE model can be used for

Recycling of high purity selenium from CIGS solar cell waste materials

Energy Technology Data Exchange (ETDEWEB)

Gustafsson, Anna M.K., E-mail: anna.gustafsson@chalmers.se; Foreman, Mark R.StJ.; Ekberg, Christian

2014-10-15

Highlights: • A new method for recycling of selenium from CIGS solar cell materials is presented. • Separation of selenium as selenium dioxide after heating in oxygen atmosphere. • Complete selenium separation after oxidation of <63 μm particles at 800 °C for 1 h. • After reduction of selenium dioxide the selenium purity was higher than 99.999 wt%. - Abstract: Copper indium gallium diselenide (CIGS) is a promising material in thin film solar cell production. To make CIGS solar cells more competitive, both economically and environmentally, in comparison to other energy sources, methods for recycling are needed. In addition to the generally high price of the material, significant amounts of the metals are lost in the manufacturing process. The feasibility of recycling selenium from CIGS through oxidation at elevated temperatures was therefore examined. During oxidation gaseous selenium dioxide was formed and could be separated from the other elements, which remained in solid state. Upon cooling, the selenium dioxide sublimes and can be collected as crystals. After oxidation for 1 h at 800 °C all of the selenium was separated from the CIGS material. Two different reduction methods for reduction of the selenium dioxide to selenium were tested. In the first reduction method an organic molecule was used as the reducing agent in a Riley reaction. In the second reduction method sulphur dioxide gas was used. Both methods resulted in high purity selenium. This proves that the studied selenium separation method could be the first step in a recycling process aimed at the complete separation and recovery of high purity elements from CIGS.

Modeling and simulation of a dual-junction CIGS solar cell using Silvaco ATLAS

OpenAIRE

Fotis, Konstantinos

2012-01-01

Approved for public release; distribution is unlimited. The potential of designing a dual-junction Copper Indium Gallium Selenide (CIGS) photovoltaic cell is investigated in this thesis. Research into implementing a dual-junction solar cell, using a CIGS bottom cell and different thin-film designs as a top cell, was conducted in order to increase the current record efficiency of 20.3% for a single CIGS cell. This was accomplished through modeling and simulation using Silvaco ATLASTM, an ad...

Semi-transparent perovskite solar cells for tandems with silicon and CIGS

KAUST Repository

Bailie, Colin D.

2015-01-01

© 2015 The Royal Society of Chemistry. A promising approach for upgrading the performance of an established low-bandgap solar technology without adding much cost is to deposit a high bandgap polycrystalline semiconductor on top to make a tandem solar cell. We use a transparent silver nanowire electrode on perovskite solar cells to achieve a semi-transparent device. We place the semi-transparent cell in a mechanically-stacked tandem configuration onto copper indium gallium diselenide (CIGS) and low-quality multicrystalline silicon (Si) to achieve solid-state polycrystalline tandem solar cells with a net improvement in efficiency over the bottom cell alone. This work paves the way for integrating perovskites into a low-cost and high-efficiency (>25%) tandem cell.

The influence of Na on metastable defect kinetics in CIGS materials

International Nuclear Information System (INIS)

Erslev, Peter T.; Lee, Jin Woo; Shafarman, William N.; Cohen, J. David

2009-01-01

The electronic properties of matched pairs of Cu(In x Ga 1-x )Se 2 (CIGS) solar cells, with and without normal sodium levels, were studied by junction capacitance methods including admittance spectroscopy, drive level capacitance profiling (DLCP) and transient photocapacitance spectroscopy (TPC). The capacitance profiling measurements revealed a large deep defect density in the vicinity of the barrier interface that was likely responsible for the lower performance of the reduced Na samples. The metastable properties of CIGS solar cells were also examined, and these revealed marked differences between the two types of samples. These results directly address the predictions of theoretical microscopic models that have been proposed to account for metastable effects in CIGS

Multi-stage pulsed laser deposition of aluminum nitride at different temperatures

Energy Technology Data Exchange (ETDEWEB)

Duta, L. [National Institute for Lasers, Plasma, and Radiation Physics, 409 Atomistilor Street, 077125 Magurele (Romania); Stan, G.E. [National Institute of Materials Physics, 105 bis Atomistilor Street, 077125 Magurele (Romania); Stroescu, H.; Gartner, M.; Anastasescu, M. [Institute of Physical Chemistry “Ilie Murgulescu”, Romanian Academy, 202 Splaiul Independentei, 060021 Bucharest (Romania); Fogarassy, Zs. [Research Institute for Technical Physics and Materials Science, Hungarian Academy of Sciences, Konkoly Thege Miklos u. 29-33, H-1121 Budapest (Hungary); Mihailescu, N. [National Institute for Lasers, Plasma, and Radiation Physics, 409 Atomistilor Street, 077125 Magurele (Romania); Szekeres, A., E-mail: szekeres@issp.bas.bg [Institute of Solid State Physics, Bulgarian Academy of Sciences, Tzarigradsko Chaussee 72, Sofia 1784 (Bulgaria); Bakalova, S. [Institute of Solid State Physics, Bulgarian Academy of Sciences, Tzarigradsko Chaussee 72, Sofia 1784 (Bulgaria); Mihailescu, I.N., E-mail: ion.mihailescu@inflpr.ro [National Institute for Lasers, Plasma, and Radiation Physics, 409 Atomistilor Street, 077125 Magurele (Romania)

2016-06-30

Highlights: • Multi-stage pulsed laser deposition of aluminum nitride at different temperatures. • 800 °C seed film boosts the next growth of crystalline structures at lower temperature. • Two-stage deposited AlN samples exhibit randomly oriented wurtzite structures. • Band gap energy values increase with deposition temperature. • Correlation was observed between single- and multi-stage AlN films. - Abstract: We report on multi-stage pulsed laser deposition of aluminum nitride (AlN) on Si (1 0 0) wafers, at different temperatures. The first stage of deposition was carried out at 800 °C, the optimum temperature for AlN crystallization. In the second stage, the deposition was conducted at lower temperatures (room temperature, 350 °C or 450 °C), in ambient Nitrogen, at 0.1 Pa. The synthesized structures were analyzed by grazing incidence X-ray diffraction (GIXRD), transmission electron microscopy (TEM), atomic force microscopy and spectroscopic ellipsometry (SE). GIXRD measurements indicated that the two-stage deposited AlN samples exhibited a randomly oriented wurtzite structure with nanosized crystallites. The peaks were shifted to larger angles, indicative for smaller inter-planar distances. Remarkably, TEM images demonstrated that the high-temperature AlN “seed” layers (800 °C) promoted the growth of poly-crystalline AlN structures at lower deposition temperatures. When increasing the deposition temperature, the surface roughness of the samples exhibited values in the range of 0.4–2.3 nm. SE analyses showed structures which yield band gap values within the range of 4.0–5.7 eV. A correlation between the results of single- and multi-stage AlN depositions was observed.

Vaping cannabis (marijuana): parallel concerns to e-cigs?

Science.gov (United States)

Budney, Alan J; Sargent, James D; Lee, Dustin C

2015-11-01

The proliferation of vaporization ('vaping') as a method for administering cannabis raises many of the same public health issues being debated and investigated in relation to e-cigarettes (e-cigs). Good epidemiological data on the prevalence of vaping cannabis are not yet available, but with current trends towards societal approval of medicinal and recreational use of cannabis, the pros and cons of vaping cannabis warrant study. As with e-cigs, vaping cannabis portends putative health benefits by reducing harm from ingesting toxic smoke. Indeed, vaping is perceived and being sold as a safer way to use cannabis, despite the lack of data on the health effects of chronic vaping. Other perceived benefits include better taste, more efficient and intense effects and greater discretion which allows for use in more places. Unfortunately, these aspects of vaping could prompt an increased likelihood of trying cannabis, earlier age of onset, more positive initial experiences, and more frequent use, thereby increasing the probability of problematic use or addiction. Sales and marketing of vaping devices with no regulatory guidelines, especially related to advertising or product development targeting youth, parallels concerns under debate related to e-cigs and youth. Thus, the quandary of whether or not to promote vaping as a safer method of cannabis administration for those wishing to use cannabis, and how to regulate vaping and vaping devices, necessitates substantial investigation and discussion. Addressing these issues in concert with efforts directed towards e-cigs may save time and energy and result in a more comprehensive and effective public health policy on vaping. © 2015 Society for the Study of Addiction.

One-pot Synthesis of Soluble Nanoscale CIGS Photoactive Functional Materials

Directory of Open Access Journals (Sweden)

Yan Aixia

2007-01-01

Full Text Available Abstract Promising alternatives for solar energy utilization are thin film technologies involving various new materials. This contribution describes an easy and inexpensive synthetic method that can be used to prepare soluble nanoscale triphenyl phosphine-coordinated CIGS (TPP-CIGS photoactive functional materials. This complex is stable in the solid state under the irradiation of the ambient light, but its solution becomes a little bit unstable under the illumination of the low intensity laser.

Identifying parasitic current pathways in CIGS solar cells by modelling dark J-V response

NARCIS (Netherlands)

Williams, B.L.; Smit, S.; Kniknie, B.J.; Bakker, K.J.; Keuning, W.; Kessels, W.M.M.; Schropp, R.E.I.; Creatore, M.

2015-01-01

An equivalent circuit model, which allows for the presence of three types of shunting pathways, has been developed to describe the dark J-V characteristics in CIGS solar cells. Excellent agreement between the model and experimental data was apparent throughout a temperature range of 183-323K.

Process parameter impact on properties of sputtered large-area Mo bilayers for CIGS thin film solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Badgujar, Amol C.; Dhage, Sanjay R., E-mail: dhage@arci.res.in; Joshi, Shrikant V.

2015-08-31

Copper indium gallium selenide (CIGS) has emerged as a promising candidate for thin film solar cells, with efficiencies approaching those of silicon-based solar cells. To achieve optimum performance in CIGS solar cells, uniform, conductive, stress-free, well-adherent, reflective, crystalline molybdenum (Mo) thin films with preferred orientation (110) are desirable as a back contact on large area glass substrates. The present study focuses on cylindrical rotating DC magnetron sputtered bilayer Mo thin films on 300 mm × 300 mm soda lime glass (SLG) substrates. Key sputtering variables, namely power and Ar gas flow rates, were optimized to achieve best structural, electrical and optical properties. The Mo films were comprehensively characterized and found to possess high degree of thickness uniformity over large area. Best crystallinity, reflectance and sheet resistance was obtained at high sputtering powers and low argon gas flow rates, while mechanical properties like adhesion and residual stress were found to be best at low sputtering power and high argon gas flow rate, thereby indicating a need to arrive at a suitable trade-off during processing. - Highlights: • Sputtering of bilayer molybdenum thin films on soda lime glass • Large area deposition using rotating cylindrical direct current magnetron • Trade of sputter process parameters power and pressure • High uniformity of thickness and best electrical properties obtained • Suitable mechanical and optical properties of molybdenum are achieved for CIGS application.

Deposition and characterization of graded Cu(In{sub 1-x}Ga{sub x})Se{sub 2} thin films by spray pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Babu, B.J. [Department of Electrical Engineering-SEES, CINVESTAV-IPN, Avenida IPN 2508, San Pedro Zacatenco, D.F. C.P 07360 (Mexico); Institute of Molecules and Materials, UMR-CNRS 6283, Université du Maine, Avenue O. Messiaen, F-72085 Le Mans (France); Velumani, S., E-mail: velu@cinvestav.mx [Department of Electrical Engineering-SEES, CINVESTAV-IPN, Avenida IPN 2508, San Pedro Zacatenco, D.F. C.P 07360 (Mexico); College of Information and Communication Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Kassiba, A. [Institute of Molecules and Materials, UMR-CNRS 6283, Université du Maine, Avenue O. Messiaen, F-72085 Le Mans (France); Asomoza, R. [Department of Electrical Engineering-SEES, CINVESTAV-IPN, Avenida IPN 2508, San Pedro Zacatenco, D.F. C.P 07360 (Mexico); Chavez-Carvayar, J.A. [Instituto Investigaciones en Materiales-UNAM, Ciudad Universitario, D.F.Mexico (Mexico); Yi, Junsin, E-mail: yi@yurim.skku.ac.kr [College of Information and Communication Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

2015-07-15

Cu(In{sub 1-x}Ga{sub x})Se{sub 2} (CIGS) thin films and their graded (x = 1 to 0) layer were grown on soda lime glass substrates using chemical spray pyrolysis (CSP) at different substrate temperatures (T{sub s}). After optimization of T{sub s}, depositions were carried out at different gallium composition (x) at optimized temperature of 350 °C. All the films deposited at T{sub s} ≥ 350 °C were polycrystalline chalcopyrite structure, with a preferential orientation of (112), including the graded layer. With increase in x, lattice parameters a and c were observed to decrease. Line scan of the CIGS layer showed intersection of gallium and indium concentrations, revealing the graded nature of the film. Composition dependence of Raman peak for CuInSe{sub 2} (CIS) deposited by CSP was analyzed. Optical transmittance at a wavelength of 800 nm of the film with x = 0 (CIS) (30%) was found lower than that of the film grown with x = 0.82 (CIGS) (50%). Cusp-shape of the resistivity was observed with an increase of x leading to steep rise in resistivity of the films (1.61–71.68 Ω-cm) till x = 0.42 and then decreased to 4.78 Ω-cm at x = 0.82. Carrier concentrations of the films were evaluated in the order of 10{sup 16}–10{sup 19} cm{sup −3} with p-type conductivity. These results indicate that graded CIGS thin films with modulated gallium composition can be prepared by CSP. - Graphical abstract: Display Omitted - Highlights: • Optimization of the spray deposition system for device grade chalcopyrite CIGS films. • Optimized substrate temperature to obtain single-phase CIGS by spray deposition. • Detailed report on compositional dependence of CuInSe{sub 2} (CIS) thin films. • Systematic analysis of the influence of Ga in CIS by spray deposition. • Bowing parameter is extracted from the experiment values.

Improved growth of solution-deposited thin films on polycrystalline Cu(In,Ga)Se{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Witte, Wolfram; Hariskos, Dimitrios [Zentrum fuer Sonnenenergie- und Wasserstoff-Forschung Baden-Wuerttemberg (ZSW), 70565, Stuttgart (Germany); Abou-Ras, Daniel [Helmholtz-Zentrum Berlin fuer Materialien und Energie, 14109, Berlin (Germany)

2016-04-15

CdS and Zn(O,S) grown by chemical bath deposition (CBD) are well established buffer materials for Cu(In,Ga)Se{sub 2} (CIGS) solar cells. As recently reported, a non-contiguous coverage of CBD buffers on CIGS grains with {112} surfaces can be detected, which was explained in terms of low surface energies of the {112} facets, leading to deteriorated wetting of the chemical solution on the CIGS surface. In the present contribution, we report on the effect of air annealing of CIGS thin films prior to the CBD of CdS and Zn(O,S) layers. In contrast to the growth on the as-grown CIGS layers, these buffer lay- ers grow densely on the annealed CIGS layer, even on grains with {112} surfaces. We explain the different growth behavior by increased surface energies of CIGS grains due to the annealing step, i.e., due to oxidation of the CIGS surface. Reference solar cells were processed and completed by i-ZnO/ZnO:Al layers for CdS and by (Zn,Mg)O/ZnO:Al for Zn(O,S) buffers. For solar cells with both, CdS and Zn(O,S) buffers, air-annealed CIGS films with improved buffer coverage resulted in higher power-conversion efficiencies, as compared with the devices containing as-grown CIGS layers. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Beneficial effect of post-deposition treatment in high-efficiency Cu(In,Ga)Se{sub 2} solar cells through reduced potential fluctuations

Energy Technology Data Exchange (ETDEWEB)

Jensen, S. A., E-mail: Soren.Jensen@nrel.gov, E-mail: Darius.Kuciauskas@nrel.gov; Glynn, S.; Kanevce, A.; Dippo, P.; Li, J. V.; Levi, D. H.; Kuciauskas, D., E-mail: Soren.Jensen@nrel.gov, E-mail: Darius.Kuciauskas@nrel.gov [National Renewable Energy Laboratory, 15013 Denver West Parkway, Golden, Colorado 80401 (United States)

2016-08-14

World-record power conversion efficiencies for Cu(In,Ga)Se{sub 2} (CIGS) solar cells have been achieved via a post-deposition treatment with alkaline metals, which increases the open-circuit voltage and fill factor. We explore the role of the potassium fluoride (KF) post-deposition treatment in CIGS by employing energy- and time-resolved photoluminescence spectroscopy and electrical characterization combined with numerical modeling. The bulk carrier lifetime is found to increase with post-deposition treatment from 255 ns to 388 ns, which is the longest charge carrier lifetime reported for CIGS, and within ∼40% of the radiative limit. We find evidence that the post-deposition treatment causes a decrease in the electronic potential fluctuations. These potential fluctuations have previously been shown to reduce the open-circuit voltage and the device efficiency in CIGS. Additionally, numerical simulations based on the measured carrier lifetimes and mobilities show a diffusion length of ∼10 μm, which is ∼4 times larger than the film thickness. Thus, carrier collection in the bulk is not a limiting factor for device efficiency. By considering differences in doping, bandgap, and potential fluctuations, we present a possible explanation for the voltage difference between KF-treated and untreated samples.

Hydrazine-Free Solution-Deposited CuIn(S,Se)2 Solar Cells by Spray Deposition of Metal Chalcogenides.

Science.gov (United States)

Arnou, Panagiota; van Hest, Maikel F A M; Cooper, Carl S; Malkov, Andrei V; Walls, John M; Bowers, Jake W

2016-05-18

Solution processing of semiconductors, such as CuInSe2 and its alloys (CIGS), can significantly reduce the manufacturing costs of thin film solar cells. Despite the recent success of solution deposition approaches for CIGS, toxic reagents such as hydrazine are usually involved, which introduce health and safety concerns. Here, we present a simple and safer methodology for the preparation of high-quality CuIn(S, Se)2 absorbers from metal sulfide solutions in a diamine/dithiol mixture. The solutions are sprayed in air, using a chromatography atomizer, followed by a postdeposition selenization step. Two different selenization methods are explored resulting in power conversion efficiencies of up to 8%.

OTRZYMYWANIE CIENKICH WARSTW ABSORBERA CIGS METODĄ ROZPYLANIA MAGNETRONOWEGO DLA ZASTOSOWAŃ FOTOWOLTAICZNYCH

Directory of Open Access Journals (Sweden)

Sławomir GUŁKOWSKI

w cienkowarstwowych ogniwach słonecznych. Metoda rozpylania magnetronowego jest efektywną metodą produkcji cienkich warstw CIGS. Proces nanoszenia warstw można podzielić na dwie zasadnicze części: pierwsza to tworzenie prekursora CIG, tj. nanoszenie warstw metalicznych miedzi, galu i indu w odpowiednich proporcjach. Etap drugi to krystalizacja absorbera CIGS w wyniku procesu wygrzewania prekursora w obecności selenu. W artykule skupiono się na opracowaniu odpowiednich proporcji poszczególnych pierwiastków wchodzących w skład prekursora. Przebadano następujące konfiguracje nanoszenia poszczególnych warstw absorbera: CuGa/In oraz CuGa/In/Cu. Poszczególne warstwy naniesione zostały na podłoże molibdenowe, stanowiące tylny kontakt ogniwa budowanego na bazie absorbera CIGS. Warstwa molibdenu została przebadana metodą czteroostrzową w celu znalezienia zależności rezystywności od grubości warstwy. Przeprowadzono analizę składu pierwiastkowego warstwy za pomocą skaningowego mikroskopu elektronowego wyposażonego w system EDS. Dla każdej z otrzymanych warstw określono atomowe współczynniki proporcji występowania miedzi oraz galu w składzie warstwy. Na podstawie otrzymanych wyników badań dokonano optymalizacji parametrów technologicznych procesu takich jak: moc katody, ciśnienie oraz czas procesu, a także temperatura. Znaleziono zależności grubości warstw w funkcji czasu nanoszenia dla ustalonych warunków ciśnienia i mocy. Grubości poszczególnych warstw określono na podstawie badań profilometrycznych. W oparciu o opracowane parametry wykonane warstwy prekursora poddawane są obróbce termicznej w celu uzyskania absorbera CIGS.

Toward GW/year of CIGS production within the next decade

Energy Technology Data Exchange (ETDEWEB)

Dhere, Neelkanth G. [Florida Solar Energy Center, 1679 Clearlake Road, Cocoa, FL 32922-5703 (United States)

2007-09-22

A detailed study carried out in 1996-1997 showed that manufacturing cost of crystalline silicon PV modules could be lowered to 1 ECU/Wp when the c-Si annual module production level reaches 500 MWp while an annual production of only 60 MWp would lower production cost of thin-film PV modules to 0.6 ECU/Wp. During 1976-2003, the PV module price has followed the 80% learning curve with cumulative production volume. However, the price reduction has slowed since because of the polysilicon supply problem. Because of their high potential for improvement, thin-film PV and especially copper (Cu)-indium (In)-gallium (Ga)-selenide (Se)-sulfide (CIGS) technology have the potential for growing at the fastest rate and consequently not only to complement the lagging c-Si PV production but also to assist in following the 80% learning curve. This paper reviews the CIGS PV manufacturing processes in comparison to those of other PV technologies and predicts that annual production volume of CIGS thin-film PV modules will exceed 1 GW/year within the next 10 years. (author)

Toward GW/year of CIGS production within the next decade

International Nuclear Information System (INIS)

Dhere, Neelkanth G.

2007-01-01

A detailed study carried out in 1996-1997 showed that manufacturing cost of crystalline silicon PV modules could be lowered to 1 ECU/Wp when the c-Si annual module production level reaches 500 MWp while an annual production of only 60 MWp would lower production cost of thin-film PV modules to 0.6 ECU/Wp. During 1976-2003, the PV module price has followed the 80% learning curve with cumulative production volume. However, the price reduction has slowed since because of the polysilicon supply problem. Because of their high potential for improvement, thin-film PV and especially copper (Cu)-indium (In)-gallium (Ga)-selenide (Se)-sulfide (CIGS) technology have the potential for growing at the fastest rate and consequently not only to complement the lagging c-Si PV production but also to assist in following the 80% learning curve. This paper reviews the CIGS PV manufacturing processes in comparison to those of other PV technologies and predicts that annual production volume of CIGS thin-film PV modules will exceed 1 GW/year within the next 10 years. (author)

TEMPERATURE EFFECT OF ELECTRICAL PROPERTIES OF CIGS ...

African Journals Online (AJOL)

2011-06-30

Jun 30, 2011 ... Key words: Thin film solar cells, SCAPS, CIGS, temperature, effiency energetic. 1. INTRODUCTION ... technology are the low material consumption and the high efficiency that has been demonstrated, which .... [2] S. Wenham, M. Green, M. Watt, Applied Photovoltaics, The University of New. South Wales ...

Development of CIGS2 thin film solar cells

International Nuclear Information System (INIS)

Dhere, Neelkanth G.; Gade, Vivek S.; Kadam, Ankur A.; Jahagirdar, Anant H.; Kulkarni, Sachin S.; Bet, Sachin M.

2005-01-01

Research and development of CuIn 1-x Ga x Se 2-y S y (CIGSS) thin-film solar cells on ultralightweight flexible metallic foil substrates is being carried out at FSEC PV Materials Lab for space applications. Earlier, the substrate size was limited to 3 cm x 2.5 cm. Large-area sputtering systems and scrubber for hydrogen selenide and sulfide have been designed and constructed for preparation of CIGSS thin-films on large (15 cm x 10 cm) substrates. A selenization/sulfurization furnace donated by Shell (formerly Siemens) Solar has also been refurbished and upgraded. The sputtering target assembly design was modified for proper clamping of targets and effective cooling. A new design of the magnetic assembly for large-area magnetron sputtering sources was implemented so as to achieve uniform deposition on large area. Lightweight stainless steel foil and ultralightweight titanium foil substrates were utilized to increase the specific power of solar cells. Sol-gel derived SiO 2 layers were coated on titanium foil by dip coating method. Deposition parameters for the preparation of molybdenum back contact layers were optimized so as to minimize the residual stress as well as reaction with H 2 S. Presently large (15 cm x 10 cm) CuIn 1-x Ga x S 2 (CIGS2) thin film solar cells are being prepared on Mo-coated titanium and stainless steel foil by sulfurization of CuGa/In metallic precursors in diluted Ar:H 2 S(4%). Heterojunction partner CdS layers are deposited by chemical bath deposition. The regeneration sequence of ZnO/ZnO:Al targets was optimized for obtaining consistently good-quality, transparent and conducting ZnO/ZnO:Al bilayer by RF magnetron-sputter deposition. Excellent facilities at FSEC PV Materials Lab are one of its kinds and could serve as a nucleus of a small pilot plant for CIGSS thin film solar cell fabrication

Self-assembled synthesis of 3D Cu(In1 − xGax)Se2 nanoarrays by one-step electroless deposition into ordered AAO template

International Nuclear Information System (INIS)

Zhang, Bin; Zheng, Maojun; Xiong, Zuzhou; Zhu, Changqing; Li, Hong; Wang, Faze; Shen, Wenzhong; Zhou, Tao; Ma, Li

2014-01-01

Quaternary nanostructured Cu(In 1 − x Ga x )Se 2 (CIGS) arrays were successfully fabricated via a novel and simple solution-based protocol on the electroless deposition method, using a flexible, highly ordered anodic aluminium oxide (AAO) substrate. This method does not require electric power, complicated sensitization processes, or complexing agents, but provides nearly 100% pore fill factor to AAO templates. The field emission scanning electron microscopy (FE-SEM) images show that we obtained uniformly three-dimensional nanostructured CIGS arrays, and we can tailor the diameter and wall thicknesses of the nanostructure by adjusting the pore diameter of the AAO and metal Mo layer. Their chemical composition was determined by energy-dispersive spectroscopy analysis, which is very close to the stoichiometric value. The Raman spectroscopy, x-ray diffraction (XRD) pattern, and transmission electron microscopy (TEM) further confirm the formation of nanostructured CIGS with prominent chalcopyrite structure. The nanostructured CIGS arrays can support the design of low-cost, highlight-trapping, and enhanced carrier collection nanostructured solar cells. (paper)

Computational Infrastructure for Geodynamics (CIG)

Science.gov (United States)

Gurnis, M.; Kellogg, L. H.; Bloxham, J.; Hager, B. H.; Spiegelman, M.; Willett, S.; Wysession, M. E.; Aivazis, M.

2004-12-01

Solid earth geophysicists have a long tradition of writing scientific software to address a wide range of problems. In particular, computer simulations came into wide use in geophysics during the decade after the plate tectonic revolution. Solution schemes and numerical algorithms that developed in other areas of science, most notably engineering, fluid mechanics, and physics, were adapted with considerable success to geophysics. This software has largely been the product of individual efforts and although this approach has proven successful, its strength for solving problems of interest is now starting to show its limitations as we try to share codes and algorithms or when we want to recombine codes in novel ways to produce new science. With funding from the NSF, the US community has embarked on a Computational Infrastructure for Geodynamics (CIG) that will develop, support, and disseminate community-accessible software for the greater geodynamics community from model developers to end-users. The software is being developed for problems involving mantle and core dynamics, crustal and earthquake dynamics, magma migration, seismology, and other related topics. With a high level of community participation, CIG is leveraging state-of-the-art scientific computing into a suite of open-source tools and codes. The infrastructure that we are now starting to develop will consist of: (a) a coordinated effort to develop reusable, well-documented and open-source geodynamics software; (b) the basic building blocks - an infrastructure layer - of software by which state-of-the-art modeling codes can be quickly assembled; (c) extension of existing software frameworks to interlink multiple codes and data through a superstructure layer; (d) strategic partnerships with the larger world of computational science and geoinformatics; and (e) specialized training and workshops for both the geodynamics and broader Earth science communities. The CIG initiative has already started to

Identification and Validation of Novel Hedgehog-Responsive Enhancers Predicted by Computational Analysis of Ci/Gli Binding Site Density

Science.gov (United States)

Richards, Neil; Parker, David S.; Johnson, Lisa A.; Allen, Benjamin L.; Barolo, Scott; Gumucio, Deborah L.

2015-01-01

The Hedgehog (Hh) signaling pathway directs a multitude of cellular responses during embryogenesis and adult tissue homeostasis. Stimulation of the pathway results in activation of Hh target genes by the transcription factor Ci/Gli, which binds to specific motifs in genomic enhancers. In Drosophila, only a few enhancers (patched, decapentaplegic, wingless, stripe, knot, hairy, orthodenticle) have been shown by in vivo functional assays to depend on direct Ci/Gli regulation. All but one (orthodenticle) contain more than one Ci/Gli site, prompting us to directly test whether homotypic clustering of Ci/Gli binding sites is sufficient to define a Hh-regulated enhancer. We therefore developed a computational algorithm to identify Ci/Gli clusters that are enriched over random expectation, within a given region of the genome. Candidate genomic regions containing Ci/Gli clusters were functionally tested in chicken neural tube electroporation assays and in transgenic flies. Of the 22 Ci/Gli clusters tested, seven novel enhancers (and the previously known patched enhancer) were identified as Hh-responsive and Ci/Gli-dependent in one or both of these assays, including: Cuticular protein 100A (Cpr100A); invected (inv), which encodes an engrailed-related transcription factor expressed at the anterior/posterior wing disc boundary; roadkill (rdx), the fly homolog of vertebrate Spop; the segment polarity gene gooseberry (gsb); and two previously untested regions of the Hh receptor-encoding patched (ptc) gene. We conclude that homotypic Ci/Gli clustering is not sufficient information to ensure Hh-responsiveness; however, it can provide a clue for enhancer recognition within putative Hedgehog target gene loci. PMID:26710299

Alternative bufferlayers for CIGS solarcells

Energy Technology Data Exchange (ETDEWEB)

Beleanu, A.; Gruhn, T.; Blum, C.G.F.; Balke, B.; Felser, C. [Institute of Inorganic and Analytical Chemistry, Johannes Gutenberg - University, Mainz (Germany)

2010-07-01

Cadmium sulfide is a highly efficient buffer layer material in Cu(In,Ga)(S,Se2)[CIGS] solar devices, but for environmental reasons and possible gains in efficiency there is a great interest in replacing CdS by a cadmium-free alternative buffer layer. Using standard density functional theory (DFT) methods possible candidates like LiZnP and LiCuS have been proposed as alternative buffer layers. The experimental verification of the DFT results was quite challenging due to the fact that LiCuS was an unknow and completely new material. In a first step, we tried to synthesize LiCuS through solid state reactions in a corund crucible. After optimizing the parameters and successfully synthesizing the material its properties were investigated. In a second step, huge amounts of LiCuS and LiZnP were synthesized and pressed using Spark Plasma Sintering as 3 inch targets. LiCuS and LiZnP films were grown by radio-frequency magnetron sputtering from these target and their properties as an alternative buffer layer in CIGS solar cells were investigated. The 1:1:1 stoichiometry of the films was delivered from in-situ XPS measurements. Absorption measurements show a band gap of {approx}2.0 eV which is in good agreement with the theoretical estimates.

A study on the optics of copper indium gallium (di)selenide (CIGS) solar cells with ultra-thin absorber layers.

Science.gov (United States)

Xu, Man; Wachters, Arthur J H; van Deelen, Joop; Mourad, Maurice C D; Buskens, Pascal J P

2014-03-10

We present a systematic study of the effect of variation of the zinc oxide (ZnO) and copper indium gallium (di)selenide (CIGS) layer thickness on the absorption characteristics of CIGS solar cells using a simulation program based on finite element method (FEM). We show that the absorption in the CIGS layer does not decrease monotonically with its layer thickness due to interference effects. Ergo, high precision is required in the CIGS production process, especially when using ultra-thin absorber layers, to accurately realize the required thickness of the ZnO, cadmium sulfide (CdS) and CIGS layer. We show that patterning the ZnO window layer can strongly suppress these interference effects allowing a higher tolerance in the production process.

CIGS thin films, solar cells, and submodules fabricated using a rf-plasma cracked Se-radical beam source

International Nuclear Information System (INIS)

Ishizuka, Shogo; Yamada, Akimasa; Shibata, Hajime; Fons, Paul; Niki, Shigeru

2011-01-01

Coevaporated Cu(In,Ga)Se 2 (CIGS) film growth using a rf-plasma cracked Se-radical beam (R-Se) source leads to a significant reduction in the amount of raw Se source material wasted during growth and exhibits unique film properties such as highly dense, smooth surfaces and large grain size. R-Se grown CIGS solar cells also show concomitant unique properties different from conventional evaporative Se (E-Se) source grown CIGS cells. In the present work, the impact of modified surfaces, interfaces, and bulk crystal properties of R-Se grown CIGS films on the solar cell performance was studied. When a R-Se source was used, Na diffusion into CIGS layers was enhanced while a remarkable diffusion of elemental Ga and Se into Mo back contact layers was observed. Improvements in the bulk crystal quality as manifested by large grain size and increased Na concentration with the use of a R-Se source is expected to be effective to improve photovoltaic performance. Using a R-Se source for the growth of CIGS absorber layers at a relatively low growth temperature, we have successfully demonstrated a monolithically integrated submodule efficiency of 15.0% (17 cells, aperture area of 76.5 cm 2 ) on 0.25-mm thick soda-lime glass substrates.

Stability of CIGS Solar Cells and Component Materials Evaluated by a Step-Stress Accelerated Degradation Test Method: Preprint

Energy Technology Data Exchange (ETDEWEB)

Pern, F. J.; Noufi, R.

2012-10-01

A step-stress accelerated degradation testing (SSADT) method was employed for the first time to evaluate the stability of CuInGaSe2 (CIGS) solar cells and device component materials in four Al-framed test structures encapsulated with an edge sealant and three kinds of backsheet or moisture barrier film for moisture ingress control. The SSADT exposure used a 15oC and then a 15% relative humidity (RH) increment step, beginning from 40oC/40%RH (T/RH = 40/40) to 85oC/70%RH (85/70) as of the moment. The voluminous data acquired and processed as of total DH = 3956 h with 85/70 = 704 h produced the following results. The best CIGS solar cells in sample Set-1 with a moisture-permeable TPT backsheet showed essentially identical I-V degradation trend regardless of the Al-doped ZnO (AZO) layer thickness ranging from standard 0.12 μm to 0.50 μm on the cells. No clear 'stepwise' feature in the I-V parameter degradation curves corresponding to the SSADT T/RH/time profile was observed. Irregularity in I-V performance degradation pattern was observed with some cells showing early degradation at low T/RH < 55/55 and some showing large Voc, FF, and efficiency degradation due to increased series Rs (ohm-cm2) at T/RH ≥ 70/70. Results of (electrochemical) impedance spectroscopy (ECIS) analysis indicate degradation of the CIGS solar cells corresponded to increased series resistance Rs (ohm) and degraded parallel (minority carrier diffusion/recombination) resistance Rp, capacitance C, overall time constant Rp*C, and 'capacitor quality' factor (CPE-P), which were related to the cells? p-n junction properties. Heating at 85/70 appeared to benefit the CIGS solar cells as indicated by the largely recovered CPE-P factor. Device component materials, Mo on soda lime glass (Mo/SLG), bilayer ZnO (BZO), AlNi grid contact, and CdS/CIGS/Mo/SLG in test structures with TPT showed notable to significant degradation at T/RH ≥ 70/70. At T/RH = 85/70, substantial blistering of

Influence of post-treatment on properties of Cu(In{sub ,}Ga)Se{sub 2} thin films deposited by RF magnetron sputtering using a quaternary single target for photovoltaic devices

Energy Technology Data Exchange (ETDEWEB)

Jung, Sung Hee; Choi, Soon Ja; Chung, Chee Won, E-mail: cwchung@inha.ac

2014-11-03

The deposition of Cu(In,Ga)Se{sub 2} (CIGS) thin films has been performed by one-step RF sputtering using a single quaternary target and followed by sulfurization to incorporate S into CIGS films. The effect of sulfurization temperature and time on the properties of the films was studied. The sulfurized Cu(In,Ga)(Se,S){sub 2} (CIGSeS) films show that the chalcopyrite peaks shifted to high diffraction angles and the CuS and InS second phases could be formed at low sulfurization temperature. These indicate possible incorporation of S into the films. The formation and disappearance of these second phases depended on the sulfurization temperature and time. The band gap increased with increasing sulfurization temperature and time because of the shift of the absorption edge due to the increase of S/(S + Se) ratio. It was revealed that the resistivity of the as-deposited CIGS film increased after sulfurization while the carrier concentration and mobility decreased. It is believed that the sulfurization process of CIGS films can be utilized as a method to control the properties of the films. - Highlights: • Development of sputtering process of CIGS thin films using single quaternary target • Effect of sulfurization temperature and time on the properties of CIGS films • Application of sulfurization process to improve the properties of CIGS films • Successful transformation of CIGS films to chalcopyrite structure through post-sulfirization.

Modeling and performance analysis dataset of a CIGS solar cell with ZnS buffer layer

Directory of Open Access Journals (Sweden)

Md. Billal Hosen

2017-10-01

Full Text Available This article represents the baseline data of the several semiconductor materials used in the model of a CIGS thin film solar cell with an inclusion of ZnS buffer layer. As well, input parameters, contact layer data and operating conditions for CIGS solar cell simulation with ZnS buffer layer have been described. The schematic diagram of photovoltaic solar cell has been depicted. Moreover, the most important performance measurement graph, J-V characteristic curve, resulting from CIGS solar cell simulation has been analyzed to estimate the optimum values of fill factor and cell efficiency. These optimum results have been obtained from the open circuit voltage, short circuit current density, and the maximum points of voltage and current density generated from the cell.

Lessons learned from NMSG-085 CIG Land Operation demonstration

NARCIS (Netherlands)

Gautreau, B.; Remmersmann, T.; Henderson, H.C.; Reus, N.M. de; Khimeche, L.; Pedersen, E.; Lillesoe, J.; Liberg, D.

2013-01-01

This paper presents the experience gained during demonstrations carried out between Denmark, France, Germany, the Netherlands and Spain under the umbrella of the NMSG-085 / CIG Land Operation group. The demonstration, also presented in this paper, focuses on command post exercise training. It

Fatal acute pancreatitis associated with reactive AA amyloidosis in rheumatoid arthritis with end-stage renal disease: a report of three cases.

Science.gov (United States)

Kuroda, Takeshi; Sato, Hiroe; Hasegawa, Hisashi; Wada, Yoko; Murakami, Shuichi; Saeki, Takako; Nakano, Masaaki; Narita, Ichiei

2011-01-01

We report three cases of fatal pancreatitis associated with systemic AA amyloidosis in rheumatoid arthritis (RA). All of the patients showed end-stage renal failure, and hemodialysis was introduced during the course of treatment. Autopsy was performed on two of the three patients, and this revealed amyloid deposition on the vascular walls in the pancreas. It was strongly suggested that the acute pancreatitis in all three patients was attributable to deposition of amyloid in vascular and pancreatic tissues. Acute pancreatitis is considered to be a rare complication of end-stage amyloidosis associated with RA, and is frequently fatal. It is important to treat RA patients intensively to avoid such deposition of amyloid.

A one-dimensional Fickian model to predict the Ga depth profiles in three-stage Cu(In,Ga)Se2

International Nuclear Information System (INIS)

Rodriguez-Alvarez, H.; Mainz, R.; Sadewasser, S.

2014-01-01

We present a one-dimensional Fickian model that predicts the formation of a double Ga gradient during the fabrication of Cu(In,Ga)Se 2 thin films by three-stage thermal co-evaporation. The model is based on chemical reaction equations, structural data, and effective Ga diffusivities. In the model, the Cu(In,Ga)Se 2 surface is depleted from Ga during the deposition of Cu-Se in the second deposition stage, leading to an accumulation of Ga near the back contact. During the third deposition stage, where In-Ga-Se is deposited at the surface, the atomic fluxes within the growing layer are inverted. This results in the formation of a double Ga gradient within the Cu(In,Ga)Se 2 layer and reproduces experimentally observed Ga distributions. The final shape of the Ga depth profile strongly depends on the temperatures, times and deposition rates used. The model is used to evaluate possible paths to flatten the marked Ga depth profile that is obtained when depositing at low substrate temperatures. We conclude that inserting Ga during the second deposition stage is an effective way to achieve this.

High throughput CIGS solar cell fabrication via ultra-thin absorber layer with optical confinement and (Cd, CBD)-free heterojunction partner

Energy Technology Data Exchange (ETDEWEB)

Marsillac, Sylvain [Old Dominion Univ., Norfolk, VA (United States)

2015-11-30

The main objective of this proposal was to use several pathways to reduce the production cost of Cu(In,Ga)Se₂ (CIGS) PV modules and therefore the levelized cost of energy (LCOE) associated with this technology. Three high cost drivers were identified, nominally: 1) Materials cost and availability; 2) Large scale uniformity; 3) Improved throughput These three cost drivers were targeted using the following pathways: 1) Reducing the thickness of the CIGS layer while enhancing materials quality; 2) Developing and applying enhanced in-situ metrology via real time spectroscopic ellipsometry; 3) Looking into alternative heterojunction partner, back contact and anti-reflection (AR) coating Eleven main Tasks were then defined to achieve these goals (5 in Phase 1 and 6 in Phase 2), with 11 Milestones and 2 Go/No-go decision points at the end of Phase 1. The key results are summarized below

An optimized efficient dual junction InGaN/CIGS solar cell: A numerical simulation

Science.gov (United States)

Farhadi, Bita; Naseri, Mosayeb

2016-08-01

The photovoltaic performance of an efficient double junction InGaN/CIGS solar cell including a CdS antireflector top cover layer is studied using Silvaco ATLAS software. In this study, to gain a desired structure, the different design parameters, including the CIGS various band gaps, the doping concentration and the thickness of CdS layer are optimized. The simulation indicates that under current matching condition, an optimum efficiency of 40.42% is achieved.

Growth and structural properties of reactively co-sputtered CIGS films and their solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Kim, Jeha [Cheongju University, Cheongju (Korea, Republic of); Park, Nae-Man [Electronics and Telecommunications Research Institute, Daejeon (Korea, Republic of)

2014-02-15

Using reactive sputtering, we fabricated stoichiometric CuIn{sub 1-x}Ga{sub x}Se{sub 2} (CIGS) thin films. Both Cu{sub 0.6}Ga{sub 0.4} (CuGa) and Cu{sub 0.4}In{sub 0.6} (CuIn) alloy targets were simultaneously sputtered under the delivery of elemental Se produced from a thermal cracker. By changing the sputtering rates of the CuGa and the CuIn, we were able to obtain the composition ratios of Cu/(Ga+In) and Ga/(Ga+In) in the range of 0.71-0.95 and 0.10-0.30, respectively. Both the grain size and the surface roughness of the CIGS film increased as the Cu/(Ga+In) ratio increased. In the X-ray diffraction analysis on CIGS films of 0.9 m, preferential growth with a [112] orientation was found, and reflections from the (211), (220)/(204), (301), (312)/(116), (400)/(008), and (332)/(316) planes were observed. The CIGS films showed the existence of Cu{sub 2-x}Se phases in the Cu-rich samples and ordered defect compound (ODC) phases in the Cu-poor films, as confirmed in the Raman measurements. A best device performance of η = 8.1%, V{sub oc} = 0.442 V, J{sub sc} = 34.3 mA/cm{sup 2}, and FF = 53.4% was obtained from a cell fabricated with a CIGS layer (t = 0.9 μm) with the Cu/(Ga+In) ratio = 0.71 and the Ga/(Ga+In) ratio = 0.10.

Notas sobre Feral y las cigüeñas, de Fernando Alonso, y la "Historia del califa cigüeña" (Wilhelm Hauff, Sara Cone Bryant

Directory of Open Access Journals (Sweden)

Hans Christian Hagedorn

2011-01-01

Full Text Available En el presente estudio se analizan las fuentes de la versión de la "Historia del califa cigüeña", incluida en la narración Feral y las cigüeñas (1971, de Fernando Alonso. Para ello se tienen en cuenta el cuento original del autor postromántico alemán Wilhelm Hauff ("Die Geschichte von Kalif Storch", 1825, y la adaptación de este cuento que Sara Cone Bryant realizó para su libro How to tell stories to children (1905, traducción española: El arte de contar cuentos, 1965.

Electrodeposition route to synthesize cigs films – an economical way ...

African Journals Online (AJOL)

user

Unlike binary conductors CIGS film preparation needs highly ... This argument also holds well in forming a hetero-junction partner CdS ..... successfully electrodeposited onto indium tin oxide substrate and it is recently reported (Li et al., 2010).

Quenching Mo optical losses in CIGS solar cells by a point contacted dual-layer dielectric spacer: a 3-D optical study.

Science.gov (United States)

Rezaei, Nasim; Isabella, Olindo; Vroon, Zeger; Zeman, Miro

2018-01-22

A 3-D optical modelling was calibrated to calculate the light absorption and the total reflection of fabricated CIGS solar cells. Absorption losses at molybdenum (Mo) / CIGS interface were explained in terms of plasmonic waves. To quench these losses, we assumed the insertion of a lossless dielectric spacer between Mo and CIGS, whose optical properties were varied. We show that such a spacer with low refractive index and proper thickness can significantly reduce absorption in Mo in the long wavelength regime and improve the device's rear reflectance, thus leading to enhanced light absorption in the CIGS layer. Therefore, we optimized a realistic two-layer MgF 2 / Al 2 O 3 dielectric spacer to exploit (i) the passivation properties of ultra-thin Al 2 O 3 on the CIGS side for potential high open-circuit voltage and (ii) the low refractive index of MgF 2 on the Mo side to reduce its optical losses. Combining our realistic spacer with optically-optimized point contacts increases the implied photocurrent density of a 750 nm-thick CIGS layer by 10% for the wavelengths between 700 and 1150 nm with respect to the reference cell. The elimination of plasmonic resonances in the new structure leads to a higher electric field magnitude at the bottom of CIGS layer and justifies the improved optical performance.

Comparison of Cu(In, Ga)Se{sub 2} thin films deposited on different preferred oriented Mo back contact by RF sputtering from a quaternary target

Energy Technology Data Exchange (ETDEWEB)

Tian, Jing [Sichuan University, College of Materials Science and Engineering, Chengdu (China); Solar Energy Research Institute, Yunnan Normal University, Education Ministry Key Laboratory of Renewable Energy Advanced Materials and Manufacturing Technology, Kunming (China); Peng, Lianqin; Chen, Jinwei; Wang, Gang; Wang, Xueqin; Kang, Hong; Wang, Ruilin [Sichuan University, College of Materials Science and Engineering, Chengdu (China)

2014-09-15

The Cu(In, Ga)Se{sub 2} (CIGS) thin films were deposited on bare glass and DC sputtered preferential oriented Mo-coated glass by RF sputtering from a single quaternary target. The structural and morphological properties of the films were characterized by X-ray diffraction (XRD), Raman spectroscope, energy dispersive X-ray spectrometer (EDS) and atomic force microscope (AFM). Preferred orientation of the Mo back contact was tuned between (110) and (211) plane by controlling the thickness. All the deposited CIGS thin films show (112) preferred oriented chalcopyrite structures. The films prepared on Mo-coated glass show higher quality crystallinity, better stoichiometry composition and more smooth surface morphology. Especially, the film on (211) oriented Mo-coated glass with the best integrated performance is expected to be a candidate absorber for high-efficiency CIGS solar cell device. (orig.)

A one-dimensional Fickian model to predict the Ga depth profiles in three-stage Cu(In,Ga)Se{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Rodriguez-Alvarez, H., E-mail: humberto.rodriguez@helmholtz-berlin.de [International Iberian Nanotechnology Laboratory, Avenida Mestre Jose Veiga s/n, 4715-330 Braga (Portugal); Helmholtz-Zentrum Berlin, Hahn-Meitner Platz 1, 14109 Berlin (Germany); Mainz, R. [Helmholtz-Zentrum Berlin, Hahn-Meitner Platz 1, 14109 Berlin (Germany); Sadewasser, S. [International Iberian Nanotechnology Laboratory, Avenida Mestre Jose Veiga s/n, 4715-330 Braga (Portugal)

2014-05-28

We present a one-dimensional Fickian model that predicts the formation of a double Ga gradient during the fabrication of Cu(In,Ga)Se{sub 2} thin films by three-stage thermal co-evaporation. The model is based on chemical reaction equations, structural data, and effective Ga diffusivities. In the model, the Cu(In,Ga)Se{sub 2} surface is depleted from Ga during the deposition of Cu-Se in the second deposition stage, leading to an accumulation of Ga near the back contact. During the third deposition stage, where In-Ga-Se is deposited at the surface, the atomic fluxes within the growing layer are inverted. This results in the formation of a double Ga gradient within the Cu(In,Ga)Se{sub 2} layer and reproduces experimentally observed Ga distributions. The final shape of the Ga depth profile strongly depends on the temperatures, times and deposition rates used. The model is used to evaluate possible paths to flatten the marked Ga depth profile that is obtained when depositing at low substrate temperatures. We conclude that inserting Ga during the second deposition stage is an effective way to achieve this.

CTS and CZTS for solar cells made by pulsed laser deposition and pulsed electron deposition

DEFF Research Database (Denmark)

Ettlinger, Rebecca Bolt

This thesis concerns the deposition of thin films for solar cells using pulsed laser deposition (PLD) and pulsed electron deposition (PED). The aim was to deposit copper tin sulfide (CTS) and zinc sulfide (ZnS) by pulsed laser deposition to learn about these materials in relation to copper zinc tin...... time. We compared the results of CZTS deposition by PLD at DTU in Denmark to CZTS made by PED at IMEM-CNR, where CIGS solar cells have successfully been fabricated at very low processing temperatures. The main results of this work were as follows: Monoclinic-phase CTS films were made by pulsed laser...... deposition followed by high temperature annealing. The films were used to understand the double band gap that we and other groups observed in the material. The Cu-content of the CTS films varied depending on the laser fluence (the laser energy per pulse and per area). The material transfer from...

Thermal Effect on a CIGS Thin-Film Solar Cell P2 Layer by Using a UV Laser

Directory of Open Access Journals (Sweden)

Dyi-Cheng Chen

2014-07-01

Full Text Available This study used ANSYS simulation software for analyzing an ultraviolet (UV (355 nm laser processing system. The laser apparatus was used in a stainless steel CIGS solar cell P2 layer for simulation analysis. CIGS films process order according to SiO2 layer, molybdenum electrode, CIGS absorbed layer, CdS buffered layer, i-ZnO penetrate light layer, TCO front electrode, MgF resist reflected materials, andelectrode materials. The simulation and experimental results were compared to obtain a laser-delineated P2 laser with a low melting and vaporization temperature. According to the simulation results, the laser function time was 135 μs, the UV laser was 0.5 W, and the P2 layer thin films were removed. The experimental results indicated that the electrode pattern of the experiment was similar to that of the simulation result, and the laser process did not damage the base plate. The analysis results confirm that the laser apparatus is effective when applied to a stainless steel CIGS solar cell P2 layer.

Semi-transparent perovskite solar cells for tandems with silicon and CIGS

KAUST Repository

Bailie, Colin D.; Christoforo, M. Greyson; Mailoa, Jonathan P.; Bowring, Andrea R.; Unger, Eva L.; Nguyen, William H.; Burschka, Julian; Pellet, Norman; Lee, Jungwoo Z.; Grä tzel, Michael; Noufi, Rommel; Buonassisi, Tonio; Salleo, Alberto; McGehee, Michael D.

2015-01-01

solar cell. We use a transparent silver nanowire electrode on perovskite solar cells to achieve a semi-transparent device. We place the semi-transparent cell in a mechanically-stacked tandem configuration onto copper indium gallium diselenide (CIGS

Monolithic two-terminal hybrid a-Si:H/CIGS tandem cells

NARCIS (Netherlands)

Blanker, J.; Vroon, Z.; Zeman, M.; Smets, A.

2016-01-01

Copper-indium-gallium-di-selenide (CIGS) is the present record holder in lab-scale thin-film photovoltaics (TFPV). One of the problems of this PV technology is the scarcity of indium. Multi-junction solar cells allow better spectral utilization of the light spectrum, while the required current

Ecotoxicological assessment of solar cell leachates: Copper indium gallium selenide (CIGS) cells show higher activity than organic photovoltaic (OPV) cells

Energy Technology Data Exchange (ETDEWEB)

Brun, Nadja Rebecca [University of Applied Sciences and Arts Northwestern Switzerland, School of Life Sciences, Gründenstrasse 40, CH-4132 Muttenz (Switzerland); Institute of Biogeochemistry and Pollutant Dynamics, ETH Zurich, Universitätsstrasse 16, CH-8092 Zürich (Switzerland); Wehrli, Bernhard [Institute of Biogeochemistry and Pollutant Dynamics, ETH Zurich, Universitätsstrasse 16, CH-8092 Zürich (Switzerland); Fent, Karl, E-mail: karl.fent@fhnw.ch [University of Applied Sciences and Arts Northwestern Switzerland, School of Life Sciences, Gründenstrasse 40, CH-4132 Muttenz (Switzerland); Institute of Biogeochemistry and Pollutant Dynamics, ETH Zurich, Universitätsstrasse 16, CH-8092 Zürich (Switzerland)

2016-02-01

Despite the increasing use of photovoltaics their potential environmental risks are poorly understood. Here, we compared ecotoxicological effects of two thin-film photovoltaics: established copper indium gallium selenide (CIGS) and organic photovoltaic (OPV) cells. Leachates were produced by exposing photovoltaics to UV light, physical damage, and exposure to environmentally relevant model waters, representing mesotrophic lake water, acidic rain, and seawater. CIGS cell leachates contained 583 μg L{sup −1} molybdenum at lake water, whereas at acidic rain and seawater conditions, iron, copper, zinc, molybdenum, cadmium, silver, and tin were present up to 7219 μg L{sup −1}. From OPV, copper (14 μg L{sup −1}), zinc (87 μg L{sup −1}) and silver (78 μg L{sup −1}) leached. Zebrafish embryos were exposed until 120 h post-fertilization to these extracts. CIGS leachates produced under acidic rain, as well as CIGS and OPV leachates produced under seawater conditions resulted in a marked hatching delay and increase in heart edema. Depending on model water and solar cell, transcriptional alterations occurred in genes involved in oxidative stress (cat), hormonal activity (vtg1, ar), metallothionein (mt2), ER stress (bip, chop), and apoptosis (casp9). The effects were dependent on the concentrations of cationic metals in leachates. Addition of ethylenediaminetetraacetic acid protected zebrafish embryos from morphological and molecular effects. Our study suggests that metals leaching from damaged CIGS cells, may pose a potential environmental risk. - Highlights: • Photovoltaics may be disposed in the environment after usage. • Copper indium gallium selenide (CIGS) and organic (OPV) cells were compared. • Morphological and molecular effects were assessed in zebrafish embryos. • Environmental condition affected metal leaching and ecotoxicological activity. • Damaged CIGS cells pose higher risk to the environment than OPV cells.

Development of CIGS2 solar cells with lower absorber thickness

Energy Technology Data Exchange (ETDEWEB)

Vasekar, Parag S.; Dhere, Neelkanth G. [Florida Solar Energy Center, University of Central Florida, 1679 Clearlake Rd., Cocoa, FL 32922 (United States); Moutinho, Helio [National Renewable Energy Laboratory, 1617 Cole Blvd. Golden, CO 80401 (United States)

2009-09-15

The availability and cost of materials, especially of indium can be a limiting factor as chalcopyrite based thin-film solar cells advance in their commercialization. The required amounts of metals can be lowered by using thinner films. When the thickness of the film decreases, there is possibility of remaining only in the small grain region because the coalescence of grains does not have an opportunity to enhance the grain size to the maximum. Solar cell performance in smaller grain chalcopyrite absorber deteriorates due to larger fraction of grain boundaries. Efforts are being made to reduce the thickness while maintaining the comparable performance. This work presents a study of preparation, morphology and other material properties of CIGS2 absorber layers with decreasing thicknesses up to 1.2 {mu}m and its correlation with the device performance. Encouraging results were obtained demonstrating that reasonable solar cell efficiencies (>10%) can be achieved even for thinner CIGS2 thin-film solar cells. (author)

Site selective doping of Zn for the p-type Cu(In,Ga)Se{sub 2} thin film for solar cell application

Energy Technology Data Exchange (ETDEWEB)

Shirakata, Sho [Faculty of Engineering, Ehime University, Matsuyama 790-8577 (Japan); Tokyo University of Science, Research Institute for Science and Technology, Noda, Chiba 278-8510 (Japan)

2017-06-15

Selective doping of a Zn impurity at the group III site in a Cu(In, Ga)Se{sub 2} (CIGS) film was performed by the doping of Zn at the first stage of the three-stage method. The p-type CIGS:Zn film was obtained, which is in contrast to the n-type CIGS:Zn film obtained by the Zn impurity doping at the second and third-stages. Based on excitation intensity dependence of photoluminescence (PL) at low-temperature, the change in the acceptor level was observed. The enhancement of carrier concentration as a result of Zn-doping in the p-type CIGS:Zn film was observed. The CIGS:Zn solar cells exhibited η of 14.5% and V{sub oc} of 0.658 V, which are higher than that of the corresponding solar cells using the undoped CIGS films. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

A study on the optics of copper indium gallium (di)selenide (CIGS) solar cells with ultra-thin absorber layers

NARCIS (Netherlands)

Xu, M.; Wachters, A.J.H.; Van Deelen, J.; Mourad, M.C.D.; Buskens, P.J.P.

2014-01-01

We present a systematic study of the effect of variation of the zinc oxide (ZnO) and copper indium gallium (di)selenide (CIGS) layer thickness on the absorption characteristics of CIGS solar cells using a simulation program based on finite element method (FEM). We show that the absorption in the

Atmospheric spatial atomic layer deposition of Zn(O,S) buffer layer for Cu(In,Ga)Se2 solar cells

NARCIS (Netherlands)

Frijters, C.H.; Poodt, P.; Illeberi, A.

2016-01-01

Zinc oxysulfide has been grown by spatial atomic layer deposition (S-ALD) and successfully applied as buffer layer in Cu(In, Ga)Se2 (CIGS) solar cells. S-ALD combines high deposition rates (up to nm/s) with the advantages of conventional ALD, i.e. excellent control of film composition and superior

Generation of electrical defects in ion beam assisted deposition of Cu(In,Ga)Se2 thin film solar cells

International Nuclear Information System (INIS)

Zachmann, H.; Puttnins, S.; Daume, F.; Rahm, A.; Otte, K.

2011-01-01

Thin films of Cu(In,Ga)Se 2 (CIGS) absorber layers for thin film solar cells have been manufactured on polyimide foil in a low temperature, ion beam assisted co-evaporation process. In the present work a set of CIGS thin films was produced with varying selenium ion energy. Solar cell devices have been manufactured from the films and characterized via admittance spectroscopy and capacitance-voltage profiling to determine the influence of the selenium ion energy on the electric parameters of the solar cells. It is shown that the impact of energetic selenium ions in the CIGS deposition process leads to a change in the activation energy and defect density and also in the spatial distribution of electrically active defects. For the interpretation of the results two defect models are taken into account.

Nd:YAG laser annealing investigation of screen-printed CIGS layer on PET: Layer annealing method for photovoltaic cell fabrication process

KAUST Repository

Alsaggaf, Ahmed; Alarousu, Erkki; Boulfrad, Samir; Rothenberger, Alexander

2014-01-01

by heat treatment using a Nd:YAG laser. The structure and morphology of the heated thin films were studied. The characterization of the CIGS powder, ink, and film was done using TGA, SEM, FIB, EDS, and XRD. TGA analysis shows that the CIGS ink is drying

Survey of CIG Data Base Generation from Imagery.

Science.gov (United States)

1980-09-01

200, February 1980. McGrath, J., "The Use of Wide-Angle Cinematic Simulators in Pilot Training", Technical Report NAVTRAEQUIPCEN 70-C-0306-1, March 1973... March 1974. 5 NAVTRAEQUIPCEN IH-318 algorithms which utilize data bases in which the inf)rmation is stored as planar polygons. In currint, real-time CIG...Vision Simulation and Motion Conference, April 1976. 42McGrath, J., "The Use of Wide-Angle Cinematic Simulators in Pilot Training", Technical Report

ZnS/Zn(O,OH)S-based buffer layer deposition for solar cells

Science.gov (United States)

Bhattacharya, Raghu N [Littleton, CO

2009-11-03

The invention provides CBD ZnS/Zn(O,OH)S and spray deposited ZnS/Zn(O,OH)S buffer layers prepared from a solution of zinc salt, thiourea and ammonium hydroxide dissolved in a non-aqueous/aqueous solvent mixture or in 100% non-aqueous solvent. Non-aqueous solvents useful in the invention include methanol, isopropanol and triethyl-amine. One-step deposition procedures are described for CIS, CIGS and other solar cell devices.

Luminescence investigation of Cu(In,Ga)Se{sub 2}solar cells with different Ga-contents grown in a three-stage-process on glass substrate

Energy Technology Data Exchange (ETDEWEB)

Wendt, Kristin; Mueller, Mathias; Hempel, Thomas; Bertram, Frank; Christen, Juergen [Institute of Experimental Physics, Otto-von-Guericke-University Magdeburg (Germany); Abou-Ras, Daniel; Rissom, Thorsten; Unold, Thomas; Schock, Hans-Werner [Helmholtz-Zentrum Berlin for Materials and Energy (Germany)

2011-07-01

A fundamental advantage of Cu(In,Ga)Se{sub 2} (CIGS) alloys as absorber materials in thin-film solar cells is their direct band gap energies which can be varied between 1.04 eV (CuInSe{sub 2}) and 1.68 eV (CuGaSe{sub 2}). Photoluminescence (PL) spectra of complete CIGS solar cells with a systematic variation of the Ga-content in the absorber layer will be presented. The CIGS cells investigated were grown on a Mo back contact sputtered on soda lime glass and have a Ga-concentration ranging over the entire range from CuInSe{sub 2} to CuGaSe{sub 2}. Samples with Ga-contents between 100 % and 33 % show two broad luminescence bands. In contrast, CuInSe{sub 2} exhibits only one broad luminescence band. Each band is composed of two or three different transitions. Varying excitation density over four orders of magnitude results for samples with Ga-content of 0 % and 33 % in a blueshift of the main peak with increasing excitation density. For higher Ga-concentrations, first a blue- and then a redshift of the dominating peak with increasing excitation density is visible. The temperature dependence of the PL spectra is investigated going from 4 K to 300 K.

Materials Characterization of CIGS solar cells on Top of CMOS chips

NARCIS (Netherlands)

Lu, J.; Liu, W.; Kovalgin, A.Y.; Sun, Y.; Schmitz, J.; Venkatasubramanian, R.; Radousky, H.; Liang, H.

2011-01-01

In the current work, we present a detailed study on the material properties of the CIGS layers, fabricated on top of the CMOS chips, and compare the results with the fabrication on standard glass substrates. Almost identical elemental composition on both glass and CMOS chips (within measurement

Photoelectrochemical water splitting for hydrogen production using combination of CIGS2 solar cell and RuO2 photocatalyst

International Nuclear Information System (INIS)

Dhere, Neelkanth G.; Jahagirdar, Anant H.

2005-01-01

This paper presents the development of photoelectrochemical (PEC) cell for water splitting setup using multiple band gap combination of CuIn 1-x Ga x S 2 (CIGS2) thin-film photovoltaic (PV) cell and ruthenium oxide (RuO 2 ) photocatalyst. FSEC PV Materials Lab has developed a PEC setup consisting of two illuminated CIGS2 cells, a ruthenium oxide (RuO 2 ) anode deposited on titanium sheet for oxygen evolution and a platinum foil cathode for hydrogen evolution. With this combination, a PEC efficiency of 4.29% has been achieved. This paper also presents the research aimed at further improvements in the PEC efficiency by employing highly efficient photoanode that can be illuminated by photons not absorbed at the PV cell and by increasing the concentration of electrolyte solution (pH 10). The former will be achieved by employing a p-type transparent and conducting layer at the back of PV cell to transmit the unabsorbed photons, and the latter will reduce the resistance offered by the electrolyte. Concentration of the electrolyte was increased by five times, and the I-V characteristics of both RuO 2 and RuS 2 were measured with and without illumination. The results indicate that PEC efficiencies of over 9% can be achieved using RuS 2 with illumination and five times concentrated pH 10 solution instead of pH 10 with normal concentration

An alternative non-vacuum and low cost ESAVD method for the deposition of Cu(In,Ga)Se{sub 2} absorber layers

Energy Technology Data Exchange (ETDEWEB)

Wang, Mingqing; Liu, Junpeng; Choy, KwangLeong [UCL Centre for Materials Discovery, University College London (United Kingdom); Hou, Xianghui [Faculty of Engineering, University of Nottingham (United Kingdom); Gibson, Paul [IMPT Ltd, Nottingham (United Kingdom); Salem, Elhamali; Koutsogeorgis, Demosthenes; Cranton, Wayne [School of Science and Technology, Nottingham Trent University (United Kingdom)

2015-01-01

In this article, an environmentally friendly and non-vacuum electrostatic spray assisted vapor deposition (ESAVD) process has been developed as an alternative and low cost method to deposit CIGS absorber layers. ESAVD is a non-vacuum chemical vapor deposition based process whereby a mixture of chemical precursors is atomized to form aerosol. The aerosol is charged and directed towards a heated substrate where it would undergo decomposition and chemical reaction to deposit a stable solid film onto the substrate. A sol containing copper, indium, and gallium salts, as well as thiourea was formulated into a homogeneous chemical precursor mixture for the deposition of CIGS films. After selenization, both XRD and Raman results show the presence of the characteristic peaks of CIGSSe in the fabricated thin films. From SEM images and XRF results, it can be seen that the deposited absorbers are promising for good performance solar cells. The fabricated solar cell with a typical structure of glass/Mo/CIGSSe/CdS/i-ZnO/ITO shows efficiency of 2.82% under 100 mW cm{sup -2} AM1.5 illumination. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Application of a substrate bias to control the droplet density on Cu(In,Ga)Se{sub 2} thin films grown by Pulsed Electron Deposition

Energy Technology Data Exchange (ETDEWEB)

Rampino, S. [IMEM-CNR Institute, Parco Area delle Scienze 37/A, 43124 Parma (Italy); Pattini, F., E-mail: rampino@imem.cnr.it [IMEM-CNR Institute, Parco Area delle Scienze 37/A, 43124 Parma (Italy); Malagù, C.; Pozzetti, L. [Department of Physics and Earth Sciences, University of Ferrara, Via Saragat, 1-44122 Ferrara (Italy); Stefancich, M. [LENS Laboratory, Masdar Institute of Science and Technology, Masdar City, PO Box 54224, Abu Dhabi (United Arab Emirates); Bronzoni, M. [IMEM-CNR Institute, Parco Area delle Scienze 37/A, 43124 Parma (Italy)

2014-07-01

One of the main shortcomings in the fabrication of thin-film solar cells by pulsed high-energy deposition techniques (i.e. Pulsed Laser Deposition or Pulsed Electron Deposition — PED), is the presence of a significant number of particulates on the film surface. This affects the morphological properties of the cell active layers and, ultimately, the performance of the final device. To reduce the density of these defects, we deposited a Cu(In,Ga)Se{sub 2} (CIGS) thin film by PED and studied the effect on the film morphology when a DC bias was applied between the substrate and the target. Our results show that a negative substrate voltage, comprised between 0 and − 300 V, can not only reduce the droplet density on the CIGS film surface of about one order of magnitude with respect to the standard unbiased case (from 6 × 10{sup 5} to 5 × 10{sup 4} cm{sup −2}), but also lower the maximum particulate size and the surface smoothness. When a positive voltage is applied, we observed that a significant increase in the droplet surface density (up to 10{sup 8} cm{sup −2}) occurs. The abrupt change in the preferred crystal orientation (switching from (112) to (220)/(204) by applying negative and positive biases, respectively) is also a direct consequence of the applied DC voltage. These results confirm that the external DC bias could be used as an additional parameter to control the physical properties of thin films grown by PED. - Highlights: • Cu(In,Ga)Se{sub 2} (CIGS) films were grown by Pulsed Electron Deposition (PED). • Positive and negative DC biases were applied between the target and the substrate. • The droplet density can be reduced by one order of magnitude by DC negative bias. • Chemical composition and grain orientation of CIGS are influenced by the DC bias. • The DC bias can be an additional parameter of PED for controlling the film properties.

Quenching Mo optical losses in CIGS solar cells by a point contacted dual-layer dielectric spacer: a 3-D optical study

NARCIS (Netherlands)

Rezaei, N.; Isabella, O.; Vroon, Z.; Zeman, M.

2018-01-01

A 3-D optical modelling was calibrated to calculate the light absorption and the total reflection of fabricated CIGS solar cells. Absorption losses at molybdenum (Mo) / CIGS interface were explained in terms of plasmonic waves. To quench these losses, we assumed the insertion of a lossless

Quenching Mo optical losses in CIGS solar cells by a point contacted dual-layer dielectric spacer : A 3-D optical study

NARCIS (Netherlands)

Rezaei, N.; Isabella, O.; Vroon, Zeger; Zeman, M.

2018-01-01

A 3-D optical modelling was calibrated to calculate the light absorption and the total reflection of fabricated CIGS solar cells. Absorption losses at molybdenum (Mo) / CIGS interface were explained in terms of plasmonic waves. To quench these losses, we assumed the insertion of a lossless

Tsunami deposits at MIS Stages 5e and 9 on Oahu, Hawaii: implications for sea level at interglacial stages

Science.gov (United States)

McMurtry, G. M.; Campbell, J. F.; Fryer, G. J.; Tappin, D. R.; Fietzke, J.

2010-12-01

Sandy, basalt-coral conglomerates associated with both beachrock and coral reefs are found at high elevations on Oahu, Hawaii. They have been attributed to either brief, sea level high-stands or storms. The Kahe Point conglomerates are at 12.5 m elevation, whereas the main stage MIS-5e reef at this location has a maximum elevation of 8.2 m. They are loosely consolidated and poorly cemented, graded, poorly sorted, and with varying amounts of basalt and coral clasts ranging from cobble to boulder size. Coral in these deposits has been U-series dated by us at between 120-125 ka (n=5). Four distinct beds, with a gently seaward tilt, are recognized in a road cut section, with each bed composed of a few cm-thick topset bed of fine-grained, shelly, calcareous sand to silt. Similar high elevation conglomerates and 5e reefs are also described at Mokapu and Kaena Points on Oahu, indicating an island-wide deposit. Older coral clasts, dated at 130 to 142 ka (n=6; oldest by alpha spectrometry) found in association with the stage 5e corals suggest reworking and incorporation of older low-stand reef material. The coarse grain size of the conglomerates indicates deposition from a high-energy event; thus a high-stand source is ruled out. We also consider that the overall lithology and up to 0.5 m bed thickness not to be the result of storms; a series of high frequency storm events is considered unlikely. The weight of the evidence in our opinion clearly indicates deposition by a series of tsunami waves. If correct, this has implications for “probabilistic” models of sea level peaks at least 6.6 m higher than present at stage 5e that use such data in their models (e. g., Kopp et al., 2009), at least for Oahu. Within about 2 km of the Kahe deposit, in a road cut at Ko Olina, there is another markedly similar high-energy, sandy basalt-bearing coral conglomerate sequence at 21 to 25 m elevation. There are at least two distinct beds about one meter in thickness, both gently seaward

CIGS cells with metallized front contact: Longer cells and higher efficiency

NARCIS (Netherlands)

Deelen, J. van; Frijters, C.

2017-01-01

We have investigated the benefit of a patterned metallization on top of a transparent conductive oxide in CIGS thin-film solar panels. It was found that cells with a grid have a higher efficiency compared to cells with only a TCO. This was observed for all cell lengths used. Furthermore, metallic

Electrical and optical characterization of the influence of chemical bath deposition time and temperature on CdS/Cu(In,Ga)Se{sub 2} junction properties in Cu(In,Ga)Se{sub 2} solar cells

Energy Technology Data Exchange (ETDEWEB)

Seo, Han-Kyu; Ok, Eun-A [Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Department of Materials Science and Engineering, Korea University, Seoul 136-701 (Korea, Republic of); Kim, Won-Mok; Park, Jong-Keuk [Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Seong, Tae-Yeon [Department of Materials Science and Engineering, Korea University, Seoul 136-701 (Korea, Republic of); Lee, Dong Wha; Cho, Hoon Young [Department of Physics, College of Engineering, Dongguk University, Seoul 100-715 (Korea, Republic of); Jeong, Jeung-hyun, E-mail: jhjeong@kist.re.kr [Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of)

2013-11-01

The effects of varying the conditions for the chemical bath deposition (CBD) of cadmium sulfide (CdS) layers on CdS/Cu(In,Ga)Se{sub 2} (CIGS) hetero-junctions were investigated using photoluminescence (PL), electroluminescence (EL), deep level transient spectroscopy (DLTS), and red-light-illuminated current-voltage (I–V) measurements. We demonstrated that varying CBD-CdS conditions such as the temperature and time influenced the recombination pathways around the CdS/CIGS junction via the formation of different electronic defects, which eventually changed the photovoltaic conversion efficiency. As the CBD-CdS time and temperature were increased, the cell efficiency decreased. PL measurements revealed that this degradation of the cell efficiency was accompanied by increases in the defect-related recombination, which were attributed to the existence of donor defects around CdS/CIGS having an energy level of 0.65 eV below conduction band, as revealed by DLTS. Increasing distortions in the red-light-illuminated I–V characteristics suggested that the related defects might also have played a critical role in metastable changes around the CdS/CIGS junction. Because the CBD-CdS time and temperature were considered to influence the diffusion of impurities into the CIGS surface, the evolution of the efficiency, PL spectra, defect populations, and red-light-illuminated I–V characteristics observed in this work could be attributed to the diffusion of impurities during the CBD-CdS process. - Highlights: • CdS layers were grown by chemical bath deposition (CBD). • The CBD-CdS influenced the efficiency of Cu(In,Ga)Se{sub 2} (CIGS) solar cell. • It could be related to slight alteration in carrier recombination around CdS/CIGS. • Photo- and electroluminescence spectra detected those alterations in recombination. • The variation of results could be related to the changes in deep-level defects.

Atomic layer deposition for photovoltaics: applications and prospects for solar cell manufacturing

International Nuclear Information System (INIS)

Van Delft, J A; Garcia-Alonso, D; Kessels, W M M

2012-01-01

Atomic layer deposition (ALD) is a vapour-phase deposition technique capable of depositing high quality, uniform and conformal thin films at relatively low temperatures. These outstanding properties can be employed to face processing challenges for various types of next-generation solar cells; hence, ALD for photovoltaics (PV) has attracted great interest in academic and industrial research in recent years. In this review, the recent progress of ALD layers applied to various solar cell concepts and their future prospects are discussed. Crystalline silicon (c-Si), copper indium gallium selenide (CIGS) and dye-sensitized solar cells (DSSCs) benefit from the application of ALD surface passivation layers, buffer layers and barrier layers, respectively. ALD films are also excellent moisture permeation barriers that have been successfully used to encapsulate flexible CIGS and organic photovoltaic (OPV) cells. Furthermore, some emerging applications of the ALD method in solar cell research are reviewed. The potential of ALD for solar cells manufacturing is discussed, and the current status of high-throughput ALD equipment development is presented. ALD is on the verge of being introduced in the PV industry and it is expected that it will be part of the standard solar cell manufacturing equipment in the near future. (paper)

Ecotoxicological assessment of solar cell leachates: Copper indium gallium selenide (CIGS) cells show higher activity than organic photovoltaic (OPV) cells.

Science.gov (United States)

Brun, Nadja Rebecca; Wehrli, Bernhard; Fent, Karl

2016-02-01

Despite the increasing use of photovoltaics their potential environmental risks are poorly understood. Here, we compared ecotoxicological effects of two thin-film photovoltaics: established copper indium gallium selenide (CIGS) and organic photovoltaic (OPV) cells. Leachates were produced by exposing photovoltaics to UV light, physical damage, and exposure to environmentally relevant model waters, representing mesotrophic lake water, acidic rain, and seawater. CIGS cell leachates contained 583 μg L(-1) molybdenum at lake water, whereas at acidic rain and seawater conditions, iron, copper, zinc, molybdenum, cadmium, silver, and tin were present up to 7219 μg L(-1). From OPV, copper (14 μg L(-1)), zinc (87 μg L(-1)) and silver (78 μg L(-1)) leached. Zebrafish embryos were exposed until 120 h post-fertilization to these extracts. CIGS leachates produced under acidic rain, as well as CIGS and OPV leachates produced under seawater conditions resulted in a marked hatching delay and increase in heart edema. Depending on model water and solar cell, transcriptional alterations occurred in genes involved in oxidative stress (cat), hormonal activity (vtg1, ar), metallothionein (mt2), ER stress (bip, chop), and apoptosis (casp9). The effects were dependent on the concentrations of cationic metals in leachates. Addition of ethylenediaminetetraacetic acid protected zebrafish embryos from morphological and molecular effects. Our study suggests that metals leaching from damaged CIGS cells, may pose a potential environmental risk. Copyright © 2015 Elsevier B.V. All rights reserved.

Photoelectrochemical water splitting for hydrogen production using combination of CIGS2 solar cell and RuO{sub 2} photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Dhere, Neelkanth G. [University of Central Florida, Florida Solar Energy Center, 1679 Clearlake Road Cocoa, FL 32922-5703 (United States)]. E-mail: dhere@fsec.ucf.edu; Jahagirdar, Anant H. [University of Central Florida, Florida Solar Energy Center, 1679 Clearlake Road Cocoa, FL 32922-5703 (United States)

2005-06-01

This paper presents the development of photoelectrochemical (PEC) cell for water splitting setup using multiple band gap combination of CuIn{sub 1-x}Ga {sub x}S{sub 2} (CIGS2) thin-film photovoltaic (PV) cell and ruthenium oxide (RuO{sub 2}) photocatalyst. FSEC PV Materials Lab has developed a PEC setup consisting of two illuminated CIGS2 cells, a ruthenium oxide (RuO{sub 2}) anode deposited on titanium sheet for oxygen evolution and a platinum foil cathode for hydrogen evolution. With this combination, a PEC efficiency of 4.29% has been achieved. This paper also presents the research aimed at further improvements in the PEC efficiency by employing highly efficient photoanode that can be illuminated by photons not absorbed at the PV cell and by increasing the concentration of electrolyte solution (pH 10). The former will be achieved by employing a p-type transparent and conducting layer at the back of PV cell to transmit the unabsorbed photons, and the latter will reduce the resistance offered by the electrolyte. Concentration of the electrolyte was increased by five times, and the I-V characteristics of both RuO{sub 2} and RuS{sub 2} were measured with and without illumination. The results indicate that PEC efficiencies of over 9% can be achieved using RuS{sub 2} with illumination and five times concentrated pH 10 solution instead of pH 10 with normal concentration.

Above-CMOS a-Si and CIGS Solar Cells for Powering Autonomous Microsystems

NARCIS (Netherlands)

Lu, J.; Liu, W.; van der Werf, C.H.M.; Kovalgin, A.Y.; Sun, Y.; Schropp, R.E.I.; Schmitz, J.

2010-01-01

Two types of solar cells are successfully grown on chips from two CMOS generations. The efficiency of amorphous-silicon (a-Si) solar cells reaches 5.2%, copperindium-gallium-selenide (CIGS) cells 7.1%. CMOS functionality is unaffected. The main integration issues: adhesion, surface topography, metal

Efficiency enhancement of CIGS compound solar cell fabricated using homomorphic thin Cr{sub 2}O{sub 3} diffusion barrier formed on stainless steel substrate

Energy Technology Data Exchange (ETDEWEB)

Sim, Jae-Kwan; Lee, Seung-Kyu; Kim, Jin-Soo; Jeong, Kwang-Un; Ahn, Haeng-Keun; Lee, Cheul-Ro, E-mail: crlee7@jbnu.ac.kr

2016-12-15

Highlights: • A chromium oxide layer is formed as diffusion barrier by thermal oxidation process on STS substrate. • A Cr{sub 2}O{sub 3} layer effectively reduces impurities diffusion into the CIGS absorber layer. • The Cr{sub 2}O{sub 3} layer plays an important role in increasing the efficiency by reduction of impurity diffusion. - Abstract: It is known that the efficiency of flexible Cu(In,Ga)Se{sub 2} (CIGS) solar cells fabricated on stainless-steel (STS) substrates deteriorates due to iron (Fe) and Cr impurities diffusing into the CIGS absorber layer. To overcome this problem, a nanoscale homomorphic chromium oxide layer was formed as a diffusion barrier by thermal oxidation on the surface of STS substrates for 1 min at 600 °C in oxygen atmosphere. By TEM and grazing-incidence X-ray diffraction (GIXRD), it was confirmed that the formed oxide layer on surface of STS substrates was a Cr{sub 2}O{sub 3} layer. It was found that the formed homomorphic Cr{sub 2}O{sub 3} thin layer of about 15 nm thickness was an effective diffusion barrier to reduce impurity diffusion into the CIGS layer by secondary ion mass spectroscopy (SIMS). In contrast to the efficiency of CIGS solar cell without homomorphic Cr{sub 2}O{sub 3} diffusion layer is 8.6%, whereas with diffusion barrier it increases to 10.6% because of impurities such as Fe and Cr from the STS substrate into the CIGS layer. It reveals that the layer formed on the surface of STS substrate by thermal oxidation process plays an important role in increasing the performance of CIGS solar cells.

CIGS Thin Film Solar Cells, phase 2 Uppsala University Final report 2006-01-01 - 2007-06-14

Energy Technology Data Exchange (ETDEWEB)

Edoff, Marika (Thin Film Solar Cell group, Dep. Technical Sciences, Uppsala Univ., P.O. Box 534, SE-751 21 Uppsala (Sweden)) (and others)

2007-06-15

The project CIGS Thin Film Solar Cells, phase 2 has been going on for 18,5 months and was interrupted in advance on the 14th of June, 2007. The decision to shorten the period was taken by the board of the Swedish Energy Agency the 14th of February. It was decided to reevaluate and re-direct the financial support to the group. A new project, CIGS Thin Film Solar Cells, phase 3, superseded this project and will go on for the initially planned project period (until 2009-12-31). During the project much of the focus has been on research on Cd-free buffer layers, with an emphasis on the interface properties between the CIGS and the buffer layer. (CIGS is a commonly used acronym for Cu(In,Ga)Se{sub 2}, which is the active absorption layer in this type of solar cells) The combination of high quality CIGS and the new buffer layers has been another field of interest. CIGS solar cell module development and computer modelling of solar cells and modules has been the third major research area. The results show that the group still holds a position as one of the leaders in the world in this field. The 18.5 % efficient Cd-free solar cell, which was obtained and independently confirmed is only one percent away from the world record and in addition it is Cd-free using a Zn(O,S) buffer layer (the world record from NREL contains Cd). By alloying ZnO with MgO instead of ZnS almost equally good results can be achieved. During the last half year an 18.1 % cell has been measured with a (Zn,Mg)O buffer layer. Solar cell module technology includes several research issues, both fundamental as e.g. modelling of cell voltage and losses as a function of distance from interconnect to interconnect, but also more development as e.g. encapsulation routines. The harsh environment test (damp heat test) run at 85 deg C and 85 % relative humidity for 1000 hours was passed for both a small (12.5x12.5 cm2) and a large (27.5x30 cm2) module within the degradation limits stated by the IEC standards, using

Effect of thermal annealing on the redistribution of alkali metals in Cu(In,Ga)Se2 solar cells on glass substrate

Science.gov (United States)

Kamikawa, Yukiko; Nishinaga, Jiro; Ishizuka, Shogo; Tayagaki, Takeshi; Guthrey, Harvey; Shibata, Hajime; Matsubara, Koji; Niki, Shigeru

2018-03-01

The precise control of alkali-metal concentrations in Cu(In,Ga)Se2 (CIGS) solar cells via post deposition treatment (PDT) has recently attracted attention. When PDT is performed at an elevated temperature, an accompanying annealing effect is expected. Here, we investigate how thermal annealing affects the redistribution of alkali metals in CIGS solar cells on glass substrates and the properties of the solar cells. In addition, we investigate the origin of non-homogeneous alkali-metal depth profiles that are typical of CIGS grown using a three-stage process. In particular, we use secondary-ion mass spectrometry measurements of the ion concentration as a function of distance from the CIGS surface to investigate the impact of thermal annealing on the distribution of alkali metals (Na, Ka, and Rb) and constituent elements (Ga and In) in the CIGS absorbers. We find that the depth profiles of the alkali metals strongly reflect the density of sites that tend to accommodate alkali metals, i.e., vacancies. Annealing at elevated temperature caused a redistribution of the alkali metals. The thermal-diffusion kinetics of alkali metals depends strongly on the species involved. We introduced low flux potassium fluoride (KF) to study a side effect of KF-PDT, i.e., Na removal from CIGS, separately from its predominant effects such as surface modification. When sufficient amounts of Na are supplied from the soda lime glass via annealing at an elevated temperature, the negative effect was not apparent. Conversely, when the Na supply was not sufficient, it caused a deterioration of the photovoltaic properties.

Effect of Thermal Annealing on the Redistribution of Alkali Metals in Cu(In,Ga)Se2 Solar Cells on Glass Substrate

Energy Technology Data Exchange (ETDEWEB)

Guthrey, Harvey L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kamikawa, Yukiko [National Institute of Advanced Industrial Science and Technology (AIST); Nishinaga, Jiro [National Institute of Advanced Industrial Science and Technology (AIST); Ishizuka, Shogo [National Institute of Advanced Industrial Science and Technology (AIST); Tayagaki, Takeshi [National Institute of Advanced Industrial Science and Technology (AIST); Shibata, Hajime [National Institute of Advanced Industrial Science and Technology (AIST); Matsubara, Koji [National Institute of Advanced Industrial Science and Technology (AIST); Niki, Shigeru [National Institute of Advanced Industrial Science and Technology (AIST)

2018-03-02

The precise control of alkali-metal concentrations in Cu(In,Ga)Se2 (CIGS) solar cells via post deposition treatment (PDT) has recently attracted attention. When PDT is performed at an elevated temperature, an accompanying annealing effect is expected. Here, we investigate how thermal annealing affects the redistribution of alkali metals in CIGS solar cells on glass substrates and the properties of the solar cells. In addition, we investigate the origin of non-homogeneous alkali-metal depth profiles that are typical of CIGS grown using a three-stage process. In particular, we use secondary-ion mass spectrometry measurements of the ion concentration as a function of distance from the CIGS surface to investigate the impact of thermal annealing on the distribution of alkali metals (Na, Ka, and Rb) and constituent elements (Ga and In) in the CIGS absorbers. We find that the depth profiles of the alkali metals strongly reflect the density of sites that tend to accommodate alkali metals, i.e., vacancies. Annealing at elevated temperature caused a redistribution of the alkali metals. The thermal-diffusion kinetics of alkali metals depends strongly on the species involved. We introduced low flux potassium fluoride (KF) to study a side effect of KF-PDT, i.e., Na removal from CIGS, separately from its predominant effects such as surface modification. When sufficient amounts of Na are supplied from the soda lime glass via annealing at an elevated temperature, the negative effect was not apparent. Conversely, when the Na supply was not sufficient, it caused a deterioration of the photovoltaic properties.

Confinement - assisted shock-wave-induced thin-film delamination (SWIFD) of copper indium gallium diselenide (CIGS) on a flexible substrate

Science.gov (United States)

Lorenz, Pierre; Zagoranskiy, Igor; Ehrhardt, Martin; Han, Bing; Bayer, Lukas; Zimmer, Klaus

2017-12-01

The laser structuring of CIGS (copper indium gallium (di)selenide) solar cell material without influence and damaging the functionality of the active layer is a challenge for laser methods The shock-wave-induced thin-film delamination (SWIFD) process allows structuring without thermal modifications due to a spatial separation of the laser absorption from the functional layer removal process. In the present study, SWIFD structuring of CIGS solar cell stacks was investigated. The rear side of the polyimide was irradiated with a KrF-Excimer laser. The laser-induced ablation process generates a traverse shock wave, and the interaction of the shock wave with the layer-substrate interface results in a delamination process. The effect of a water confinement on the SWIFD process was studied where the rear side of the substrate was covered with a ∼2 mm thick water layer. The resultant surface morphology was analysed and discussed. At a sufficient number of laser pulses N and laser fluences Φ, the CIGS layer can be selectively removed from the Mo back contact. The water confinement, as well as the increasing laser beam size A0 and N, results in the reduction of the necessary minimal laser fluence Φth. Further, the delaminated CIGS area increased with increasing Φ, N, and A0.

Zinc Sulfide Buffer Layer for CIGS Solar Cells Prepared by Chemical Bath Deposition

Directory of Open Access Journals (Sweden)

Rui-Wei You

2016-11-01

Full Text Available In this study, ZnS thin films were successfully synthesized by chemical bath deposition (CBD with starting materials of NH2-NH2, SC(NH22, and ZnSO4‧7H2O. ZnS thin films were deposited with different time on glass substrates by CBD at 80oC and pH=9. Based on X-ray diffraction (XRD patterns, it is found that the ZnS thin films exhibit cubic polycrystalline phase. It was found that the optimum deposition time is 90 min for preparing ZnS thin film that is suitable as buffer layer for CuIn1-xGaxSe2 solar cells. The thin film deposited for 90 min has high transmittance up to 80% in the spectra range from 350 nm to 800 nm, and the optical band gap is about 3.59 eV.

Integration of Solar Cells on Top of CMOS Chips - Part II: CIGS Solar Cells

NARCIS (Netherlands)

Lu, J.; Liu, Wei; Kovalgin, Alexeij Y.; Sun, Yun; Schmitz, Jurriaan

2011-01-01

We present the monolithic integration of deepsubmicrometer complementary metal–oxide–semiconductor (CMOS) microchips with copper indium gallium (di)selenide (CIGS) solar cells. Solar cells are manufactured directly on unpackaged CMOS chips. The microchips maintain comparable electronic performance,

Investigations on electron beam evaporated Cu(In{sub 0.85}Ga{sub 0.15})Se{sub 2} thin film solar cells

Energy Technology Data Exchange (ETDEWEB)

Venkatachalam, M.; Kannan, M.D.; Prasanna, S.; Jayakumar, S.; Balasundaraprabhu, R. [Thin Film Center, Department of Physics, PSG College of Technology, Coimbatore (India); Muthukumarasamy, N. [Department of Physics, Coimbatore Institute of Technology, Coimbatore (India); Saroja, M. [Department of Electronics, Erode Arts College, Erode (India)

2009-09-15

CIGS bulk with composition of CuIn{sub 0.85}Ga{sub 0.15}Se{sub 2} was synthesized by direct reaction of elemental copper, indium, gallium and selenium. CIGS thin films were then deposited onto well-cleaned glass substrates using the prepared bulk alloy by electron beam deposition method. The structural properties of the deposited films were studied using X-ray diffraction technique. The as-deposited CIGS films were found to be amorphous. On annealing, the films crystallized with a tetragonal chalcopyrite structure. An intermediate Cu-rich phase precipitated at 200 C and dissociated at higher annealing temperatures. Average grain size calculated from the XRD spectra indicated that the films had a nano-crystalline structure and was further corroborated by AFM analysis of the sample surface. The chemical constituents present in the deposited CIGS films were identified using energy dispersive X-ray analysis. CIGS based solar cells were then fabricated on molybdenum and ITO coated glass substrates and the efficiencies have been evaluated. (author)

Nanosolar: Delivering Grid-Parity Solar Electricity

Energy Technology Data Exchange (ETDEWEB)

Sager, Brian [Nanosolar, Inc., San Jose, CA (United States)

2012-05-31

Nanosolar has developed proprietary technology based on Copper-Indium-Gallium-diSelenide (CIGS) absorber technology that allows the printing of this semiconductor material using a high-speed, high-throughput roll-to-roll manufacturing process. A central challenge in cost-effectively constructing a large-area CIGS-based solar cell or module is that the elements of the CIGS layer must be within a narrow stoichiometric ratio on nano-, meso-, and macroscopic length scale in all three dimensions in order for the resulting cell or module to be highly efficient. Achieving precise stoichiometric composition over relatively large substrate areas is however difficult using traditional vacuum-based deposition processes. For example, it is difficult to uniformly deposit compounds and/or alloys containing more than one element by sputtering or evaporation. Both techniques rely on deposition approaches that are limited to line-of-sight and limited-area sources, tending to result in poor surface coverage. Line-of-sight trajectories and limited-area sources can result in non-uniform three-dimensional distribution of the elements in all three dimensions and/or poor film-thickness uniformity over large areas. These non-uniformities can occur over the nano-, meso-, and/or macroscopic scales. Such non-uniformity also alters the local stoichiometric ratios of the absorber layer, decreasing the potential power conversion efficiency of the complete cell or module. Nanosolar has overcome these challenges by printing nanoparticulate CIGS precursor materials onto low-cost metal foil substrates, and performing a rapid thermal processing to convert the nanoparticulate coating into a CIGS absorber layer By locking in the appropriate stochiometry into the nanoparticulate precursor material, spatial uniformity is ensured in the coated layers, while printing at high speed and throughput minimizes solar cell cost.

Atmospheric spatial atomic-layer-deposition of Zn(O, S) buffer layer for flexible Cu(In, Ga)Se2 solar cells: From lab-scale to large area roll to roll processing

NARCIS (Netherlands)

Frijters, C.H.; Bolt, P.J.; Poodt, P.W.G.; Knaapen, R.; Brink, J. van den; Ruth, M.; Bremaud, D.; Illiberi, A.

2016-01-01

In this manuscript we present the first successful application of a spatial atomic-layer-deposition process to thin film solar cells. Zn(O,S) has been grown by spatial atomic layer deposition (S-ALD) at atmospheric pressure and applied as buffer layer in rigid and flexible CIGS cells by a lab-scale

Review on Alkali Element Doping in Cu(In,GaSe2 Thin Films and Solar Cells

Directory of Open Access Journals (Sweden)

Yun Sun

2017-08-01

Full Text Available This paper reviews the development history of alkali element doping on Cu(In,GaSe2 (CIGS solar cells and summarizes important achievements that have been made in this field. The influences of incorporation strategies on CIGS absorbers and device performances are also reviewed. By analyzing CIGS surface structure and electronic property variation induced by alkali fluoride (NaF and KF post-deposition treatment (PDT, we discuss and interpret the following issues: ① The delamination of CIGS thin films induced by Na incorporation facilitates CuInSe2 formation and inhibits Ga during low-temperature co-evaporation processes. ② The mechanisms of carrier density increase due to defect passivation by Na at grain boundaries and the surface. ③ A thinner buffer layer improves the short-circuit current without open-circuit voltage loss. This is attributed not only to better buffer layer coverage in the early stage of the chemical bath deposition process, but also to higher donor defect (CdCu+ density, which is transferred from the acceptor defect (VCu− and strengthens the buried homojunction. ④ The KF-PDT-induced lower valence band maximum at the absorber surface reduces the recombination at the absorber/buffer interface, which improves the open-circuit voltage and the fill factor of solar cells.

MINERALOGICAL AND GEOCHEMICAL EVIDENCE FOR MULTI-STAGE FORMATION OF THE CHERTOVO KORYTO DEPOSIT

Directory of Open Access Journals (Sweden)

Yu. I. Tarasova

2016-01-01

sulphidization presented by scattered impregnations of pyrrhotite, as evidenced by small lenses of pyrrhotite, which are considerably elongated (axes up to 0.7 cm long along the foliation planes (Figs 3, a, b;- Ore mineralization represented by a superimposed hydrothermal gold association with arsenopyrite (Fig. 3, d;- Late chalcophilic mineralization formed at the final stage of hydrothermal-metasomatic process (Figs 3, e, f;- Post-ore silification.Geochemical characteristics. The geochemical study of rocks and ores from the Chertovo Koryto deposit show that the rocks of the Mikhailovsk Formation are characterized by higher contents of rock-forming elements, such as of Al2O3, Fe2O3total, MgO, K2O, and P2O5, in comparison to the PAAS standards [Condie, 1993] and the black shale standard composition (SChS-1 [Petrov et al., 2004]. A characteristic feature of the ore zone is that the contents of practically all the oxides, except SiO2, tend to decrease (Table 1. The distribution of rare elements repeats the pattern established for major elements. The least metamorphosed rocks of the Mikhailovsk Formation have higher contents (up to three times of Cu, Mo, Ba, W, As, Pb relative to the values in the PAAS and SChS-1 standards. In the ore zone, the contents of almost all rare elements are considerably reduced (Table 2. The contents of elements in the siderophile group (Co, Ni are clearly correlated with the ore processes and increased more than twice in the area of metamorphic changes. Samples with gold-ore grade contents show the highest concentrations of Co and Ni.Conclusion. In our opinion, the Chertovo Koryto deposit was formed in five stages, the first two of which were pre-ore, with ore preparation, and probably considerably distant in time from the main ore-generating event. The staged formation of the Chertovo Koryto deposit correlates with the basic stages in the tectono-metamorphic history of the study region and is consistent with the model showing the formation of Sukhoi

Indium tin oxide with titanium doping for transparent conductive film application on CIGS solar cells

Energy Technology Data Exchange (ETDEWEB)

Liu, Wei-Sheng; Cheng, Huai-Ming; Hu, Hung-Chun; Li, Ying-Tse; Huang, Shi-Da; Yu, Hau-Wei [Department of Photonics Engineering, Yuan Ze University, Chung-Li 32003, Taiwan (China); Pu, Nen-Wen, E-mail: nwpuccit@gmail.com [Department of Photonics Engineering, Yuan Ze University, Chung-Li 32003, Taiwan (China); Liang, Shih-Chang [Materials & Electro-Optics Research Division, National Chung-Shan Institute of Science and Technology, Lung Tan 32599, Taiwan (China)

2015-11-01

Highlights: • Ti-doped indium tin oxide (ITO) films were deposited by DC magnetron sputtering. • Optimal optoelectronic properties were achieved at a sputtering power of 100 W. • Resistivity = 3.2 × 10{sup −4} Ω-cm without substrate heating or post growth annealing. • Mean visible and NIR transmittances of 83 and 80%, respectively, were achieved. • Efficient batteries (11.3%) were fabricated by applying ITO:Ti to CIGS solar cells. - Abstract: In this study, Ti-doped indium tin oxide (ITO:Ti) thin films were fabricated using a DC-magnetron sputtering deposition method. The thin films were grown without introducing oxygen or heating the substrate, and no post-growth annealing was performed after fabrication. The thickness of the ITO:Ti thin films (350 nm) was controlled while increasing the sputtering power from 50 to 150 W. According to the results, the optimal optoelectronic properties were observed in ITO:Ti thin films grown at a sputtering power of 100 W, yielding a reduced resistivity of 3.2 × 10{sup −4} Ω-cm and a mean high transmittance of 83% at wavelengths ranging from 400 to 800 nm. The optimal ITO:Ti thin films were used to fabricate a Cu(In,Ga)Se{sub 2} solar cell that exhibited a photoelectric conversion efficiency of 11.3%, a short-circuit current density of 33.1 mA/cm{sup 2}, an open-circuit voltage of 0.54 V, and a fill factor of 0.64.

Cost and Potential of Monolithic CIGS Photovoltaic Modules

Energy Technology Data Exchange (ETDEWEB)

Horowitz, Kelsey; Woodhouse, Michael

2015-06-17

A bottom-up cost analysis of monolithic, glass-glass Cu(In,Ga)(Se,S)2 (CIGS) modules is presented, illuminating current cost drivers for this technology and possible pathways to reduced cost. At 14% module efficiency, for the case of U.S. manufacturing, a manufacturing cost of $0.56/WDC and a minimum sustainable price of $0.72/WDC were calculated. Potential for reduction in manufacturing costs to below $0.40/WDC in the long-term may be possible if module efficiency can be increased without significant increase in $/m2 costs. The levelized cost of energy (LCOE) in Phoenix, AZ under different conditions is assessed and compared to standard c-Si.

Comparative study of the role of Ga in CIGS solar cells with different thickness

Energy Technology Data Exchange (ETDEWEB)

Han, Anjun, E-mail: haj211@mail.sim.ac.cn [Institute of Photo Electronics Thin Film Devices and Technique of Nankai University, Tianjin 300071 (China); Research Center for New Energy Technology, Shanghai Institute of Microsystem and Information Technology (SIMIT), Chinese Academy of Sciences (CAS), 235 Chengbei Road, Jiading, Shanghai 201800 (China); Sun, Yun; Zhang, Yi [Institute of Photo Electronics Thin Film Devices and Technique of Nankai University, Tianjin 300071 (China); Liu, Xiaohui; Meng, Fanying; Liu, Zhengxin [Research Center for New Energy Technology, Shanghai Institute of Microsystem and Information Technology (SIMIT), Chinese Academy of Sciences (CAS), 235 Chengbei Road, Jiading, Shanghai 201800 (China)

2016-01-01

Cu(In, Ga)Se{sub 2} (CIGS) thin films with thickness of 1 μm and 2 μm are prepared by co-evaporation process, and the different Ga/(Ga + In) are achieved by varying the temperature of Ga source. The morphology, structure, minimum band gap, and performance of solar cells are comparatively studied. As Ga/(Ga + In) increases, little changes can be observed in the crystal quality of 1 μm CIGS films, while the grain size of 2 μm films decreases significantly. (112) diffraction peak intensities of the 1 μm and 2 μm films decrease and increase, respectively. In the case of the same Ga/(Ga + In), the minimum band gap values of 1 μm films are larger than that of 2 μm films, and the difference becomes large with Ga/(Ga + In) increasing. The minimum band gap values of 1 μm films are more sensitive to variation of the Ga/(Ga + In). As Ga/(Ga + In) increases, a more improvement of the efficiency of solar cells with thickness of 1 μm is obtained due to the large enhancement of the open-circuit voltage, and the efficiency reaches the maximum value when Ga/(Ga + In) is about 0.37. - Highlights: • The role of Ga in CIGS solar cells with different thickness is comparatively studied. • Effect of Ga on the material properties of 1 μm and 2 μm films is totally different. • The minimum band gap of thinned films is more sensitive to variation of Ga/(Ga + In). • Efficiency of thinned solar cells increases more significantly with Ga increasing.

High-throughput combinatorial chemical bath deposition: The case of doping Cu (In, Ga) Se film with antimony

Science.gov (United States)

Yan, Zongkai; Zhang, Xiaokun; Li, Guang; Cui, Yuxing; Jiang, Zhaolian; Liu, Wen; Peng, Zhi; Xiang, Yong

2018-01-01

The conventional methods for designing and preparing thin film based on wet process remain a challenge due to disadvantages such as time-consuming and ineffective, which hinders the development of novel materials. Herein, we present a high-throughput combinatorial technique for continuous thin film preparation relied on chemical bath deposition (CBD). The method is ideally used to prepare high-throughput combinatorial material library with low decomposition temperatures and high water- or oxygen-sensitivity at relatively high-temperature. To check this system, a Cu(In, Ga)Se (CIGS) thin films library doped with 0-19.04 at.% of antimony (Sb) was taken as an example to evaluate the regulation of varying Sb doping concentration on the grain growth, structure, morphology and electrical properties of CIGS thin film systemically. Combined with the Energy Dispersive Spectrometer (EDS), X-ray Photoelectron Spectroscopy (XPS), automated X-ray Diffraction (XRD) for rapid screening and Localized Electrochemical Impedance Spectroscopy (LEIS), it was confirmed that this combinatorial high-throughput system could be used to identify the composition with the optimal grain orientation growth, microstructure and electrical properties systematically, through accurately monitoring the doping content and material composition. According to the characterization results, a Sb2Se3 quasi-liquid phase promoted CIGS film-growth model has been put forward. In addition to CIGS thin film reported here, the combinatorial CBD also could be applied to the high-throughput screening of other sulfide thin film material systems.

Three-stage method for interpretation of uranium-lead isotopic data

International Nuclear Information System (INIS)

Nejmark, L.A.; Ovchinnikova, G.V.; Levchenkov, O.A.

1982-01-01

Three-dimensional approach for the iterpretation of uranium-lead isoto e ratios in pnatural systems, development of which corresponds to three stages, has been considered. In the framework of the three-stage model two cases, differing in the character of uranium-lead systems violation at the beginning of the third stage, are discussed. The first case corresponds to uranium addition or lead substraction, and the second one - to addition of lead of unknown isotopic content. Three-stage approach permits without amending the isotopic content of lead captured during crystallization to calculated the beginning of the second and third stages of uranium-lead systems development and to evaluate parameters of lead added to the system. Concrete examples of interpretation of uranium-lead isotopic ratios in minerals and rock samples as a whole both of the terrestrial and cosmic origin are considered. Possibilities and limitations of the three-stage approach are analyzed and directions of further development are outlined

Laser chemical vapor deposition of millimeter scale three-dimensional shapes

Science.gov (United States)

Shaarawi, Mohammed Saad

2001-07-01

Laser chemical vapor deposition (LCVD) has been successfully developed as a technique to synthesize millimeter-scale components directly from the gas phase. Material deposition occurs when heat generated by the interaction of a laser beam with a substrate thermally decomposes the gas precursor. Selective illumination or scanning the laser beam over portions of a substrate forms the single thin layer of material that is the building block of this process. Sequential scanning of the laser in a pre-defined pattern on the substrate and subsequent deposit causes the layers to accumulate forming the three-dimensional shape. The primary challenge encountered in LCVD shape forming is the synthesis of uniform layers. Three deposition techniques are studied to address this problem. The most successful technique, Active Surface Deposition, is based on the premise that the most uniform deposits are created by measuring the deposition surface topology and actively varying the deposition rate in response to features at the deposition surface. Defects observed in the other techniques were significantly reduced or completely eliminated using Active Surface Deposition. The second technique, Constant Temperature Deposition, maintains deposit uniformity through the use of closed-loop modulation of the laser power to sustain a constant surface temperature during deposition. The technique was successful in depositing high quality graphite tubes >2 mm tall from an acetylene precursor and partially successful in depositing SiC + C composite tubes from tetramethylsilane (TMS). The final technique, Constant Power Deposition, is based on the premise that maintaining a uniform power output throughout deposition would result in the formation of uniform layers. Constant Power Deposition failed to form coherent shapes. Additionally, LCVD is studied using a combination of analytic and numerical models to gain insight into the deposition process. Thermodynamic modeling is used to predict the

Daily users compared to less frequent users find vape as or more satisfying and less dangerous than cigarettes, and are likelier to use non-cig-alike vaping products.

Science.gov (United States)

Kozlowski, Lynn T; Homish, D Lynn; Homish, Gregory G

2017-06-01

We assessed the roles of perceived satisfaction and perceived danger and vaping-product-type as correlates of more frequent use of vaping products. In a baseline assessment of a longitudinal study of US Army Reserve/National Guard Soldiers and their partners (New York State, USA, 2014-2016), participants were asked about current use of vaping products (e-cigarettes) and perceived satisfaction and danger in comparison to cigarettes as well as type of product used. Fisher-exact tests and multiple ordinal logistic regressions were used. In multivariable and univariate models, more perceived satisfaction, less perceived danger, and use of non-cig-alike products were associated with more frequent use of vaping products ( p s < 0.05, two-tailed). For self-selected, more frequent adult users, e-cigs can be at least as satisfying as cigarettes and often more satisfying and are perceived as less dangerous than cigarettes. Non-cig-alike products were more likely in daily users. Some concern that e-cigs are a gateway to cigarettes arises from assuming that e-cigs may not be as reinforcing and pleasurable as cigarettes. These results indicate that accurate perception of comparative risk and use of more effective-nicotine delivery product can produce for some users a highly-satisfying alternative to cigarettes.

Daily users compared to less frequent users find vape as or more satisfying and less dangerous than cigarettes, and are likelier to use non-cig-alike vaping products

Directory of Open Access Journals (Sweden)

Lynn T. Kozlowski

2017-06-01

Full Text Available We assessed the roles of perceived satisfaction and perceived danger and vaping-product-type as correlates of more frequent use of vaping products. In a baseline assessment of a longitudinal study of US Army Reserve/National Guard Soldiers and their partners (New York State, USA, 2014–2016, participants were asked about current use of vaping products (e-cigarettes and perceived satisfaction and danger in comparison to cigarettes as well as type of product used. Fisher-exact tests and multiple ordinal logistic regressions were used. In multivariable and univariate models, more perceived satisfaction, less perceived danger, and use of non-cig-alike products were associated with more frequent use of vaping products (ps < 0.05, two-tailed. For self-selected, more frequent adult users, e-cigs can be at least as satisfying as cigarettes and often more satisfying and are perceived as less dangerous than cigarettes. Non-cig-alike products were more likely in daily users. Some concern that e-cigs are a gateway to cigarettes arises from assuming that e-cigs may not be as reinforcing and pleasurable as cigarettes. These results indicate that accurate perception of comparative risk and use of more effective-nicotine delivery product can produce for some users a highly-satisfying alternative to cigarettes.

Expanding thermal plasma chemical vapour deposition of ZnO:Al layers for CIGS solar cells

NARCIS (Netherlands)

Sharma, K.; Williams, B.L.; Mittal, A.; Knoops, H.C.M.; Kniknie, B.J.; Bakker, N.J.; Kessels, W.M.M.; Schropp, R.E.I.; Creatore, M.

2014-01-01

Aluminium-doped zinc oxide (ZnO:Al) grown by expanding thermal plasma chemical vapour deposition (ETP-CVD) has demonstrated excellent electrical and optical properties, which make it an attractive candidate as a transparent conductive oxide for photovoltaic applications. However, when depositing

Semi-transparent photovoltaic glazing based on electrodeposited CIGS solar cells on patterned molybdenum/glass substrates

Science.gov (United States)

Sidali, Tarik; Bou, Adrien; Coutancier, Damien; Chassaing, Elisabeth; Theys, Bertrand; Barakel, Damien; Garuz, Richard; Thoulon, Pierre-Yves; Lincot, Daniel

2018-03-01

In this paper, a new way of preparing semi-transparent solar cells using Cu(In1-xGax)Se2 (CIGS) chalcopyrite semiconductors as absorbers for BIPV applications is presented. The key to the elaboration process consists in the co-electrodeposition of Cu-In-Ga mixed oxides on submillimetric hole-patterned molybdenum substrate, followed by thermal reduction to metallic alloys and selenisation. This method has the advantage of being a selective deposition technique where the thin film growth is carried out only on Mo covered areas. Thus, after annealing, the transparency of the sample is always preserved, allowing light to pass through the device. A complete device (5 × 5 cm2) with 535 μm diameter holes and total glass aperture of around 35% shows an open circuit voltage (VOC) of 400 mV. Locally, the I-V curves reveal a maximum efficiency of 7.7%, VOC of 460 mV, JSC of 24 mA.cm-2 in an area of 0.1 cm2 with 35% aperture. This efficiency on the semi-transparent area is equivalent to a record efficiency of 11.9% by taking into account only the effective area.

The exposure of CIGS solar cells to different electrical biases in a damp-heat illumination environment

NARCIS (Netherlands)

Theelen, M.; Steijvers, H.; Bakker, K.; Vink, J.; Mortazavi, S.; Mulder, A.; Barreau, N.; Roosen, D.; Haverkamp, E.

2016-01-01

Two hybrid degradation setups, allowing exposure of solar cells and modules to elevated temperatures and humidity as well as illumination have been built. CIGS solar cells were placed in the degradation setups, allowing real time monitoring of their electrical properties. Under open circuit

The development of hydrazine-processed Cu(In,Ga)(Se,S){sub 2} solar cells

Energy Technology Data Exchange (ETDEWEB)

Bob, Brion; Lei, Bao; Chung, Choong-Heui; Yang, Wenbing; Hsu, Wan-Ching; Duan, Hsin-Sheng; Hou, William Wei-Jen; Li, Sheng-Han; Yang, Yang [Department of Materials Science and Engineering, University of California, Los Angeles, CA (United States)

2012-05-15

The hydrazine-based deposition of Cu(In,Ga)(S,Se){sub 2} (CIGS) thin films has attracted considerable attention in recent years due to its potential for the high-throughput production of photovoltaic devices based on this absorber material. This article provides an introduction as well as presenting a complete picture of the current status of hydrazine-based CIGS solar-cell fabrication, including the three major steps of this deposition process: dissolution of the precursor materials in hydrazine, deposition of a film from the resulting precursor solution, and the completion and characterization of a photovoltaic device following absorber deposition. Recent discoveries are then discussed, regarding the dissolution chemistry of the relevant precursor complexes in hydrazine, which together represent the true foundation of this processing method. Recent studies on CIGS film formation are then summarized, including the control and analysis of the crystalline phase, electronic bandgap, and film morphology. Finally, the latest progress in high-performance device fabrication is highlighted, with a focus on optoelectronic characterization including current-voltage, junction capacitance, and minority carrier lifetime measurements. Finally, a discussion and future outlook is provided. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Responses of Soil Acid Phosphomonoesterase Activity to Simulated Nitrogen Deposition in Three Forests of Subtropical China

Institute of Scientific and Technical Information of China (English)

HUANG Wen-Juan; LIU Shi-Zhong; CHU Guo-Wei; ZHANG De-Qiang; LI Yue-Lin; LU Xian-Kai; ZHANG Wei; HUANG Juan; D. OTIENO; Z. H. XU; LIU Ju-Xiu

2012-01-01

Soil acid phosphomonoesterase activity (APA) plays a vital role in controlling phosphorus (P) cycling and reflecting the current degree of P limitation Responses of soil APA to elevating nitrogen (N) deposition are important because of their potential applications in addressing the relationship between N and P in forest ecosystems.A study of responses of soll APA to simulated N deposition was conducted in three succession forests of subtropical China.The three forests include a Masson pine (Pinus massoniana) forest (MPF)—pioneer community,a coniferous and broad-leaved mixed forest (MF)—transition community and a monsoon evergreen broadleaved forest (MEBF)—climax community.Four N treatments were designed for MEBF:control (without N added),low-N (50 kg N ha-1 year-1),and medium-N (100 kg N ha-1 year-1) and high-N (150 kg N ha-1 year-1),and only three N treatments (i.e.,control,low-N,mediun-N) were established for MPF and MF.Results showed that soil APA was highest in MEBF.followed by MPF and MF.Soil APAs in both MPF and MF were not influenced by low-N treatments but depressed in medium-N trcatments.However,soil APA in MEBF exhibited negative responses to high N additions,indicating that the environment of enhanced N depositions would reduce P supply for the mature forest ecosystem.Soil APA and its responses to N additions in subtropical forests were closely related to the succession stages in the forests.

One-dimensional simulation of a stirling three-stage pulse-tube refrigerator

NARCIS (Netherlands)

Etaati, M.A.; Mattheij, R.M.M.; Tijsseling, A.S.; Waele, de A.T.A.M.

2009-01-01

A one-dimensional mathematical model is derived for a three-stage pulse-tube refrigerator (PTR) that is based on the conservation laws and the ideal gas law. The three-stage PTR is regarded as three separate single-stage PTRs that are coupled via proper junction conditions. At the junctions there

One-dimensional simulation of a Stirling three-stage pulse-tube refrigerator

NARCIS (Netherlands)

Etaati, M.A.; Mattheij, R.M.M.; Tijsseling, A.S.; Waele, de A.T.A.M.

2009-01-01

A one-dimensional mathematical model is derived for a three-stage pulse-tube refrigerator (PTR) that is based on the conservation laws and the ideal gas law. The three-stage PTR is regarded as three separate single-stage PTRs that are coupled via proper junction conditions. At the junctions there

In-situ sol-gel synthesis and thin film deposition of Cu(In,Ga)(S,Se)2 solar cells

International Nuclear Information System (INIS)

Oliveira, L.; Lyubenova, T.; Marti, R.; Fraga, D.; Rey, A.; Carda, J.; Kozhukharov, V.

2013-01-01

Full text: Nowadays chalcogenide-based solar cells, like Cu(In,Ga)Se 2 , are competitive in the photovoltaic market, due to its improved performances like higher efficiency (20,3%), long-time stability and excellent durability. In addition, CIGS stand out with an exceptionally high absorption coefficient (more than; 105/cm for 1.5eV) and higher energy photons. These properties make it an excellent candidate as an absorber material for large scale production of photovoltaic modules for building-integrated applications. Traditional methods of manufacture involve vacuum processes including co-evaporation and sputtering that increase production costs. With the aim to lower the expenses by using non-vacuum solution processes we propose an ‘in-situ’ sol-gel synthesis route and direct thin film deposition in the same production step. As a result, we achieved better stoichiometric control, simplicity in the procedure and cost reduction. In this work we describe a procedure to obtain CIGS absorber layer by soft chemistry technique and further deposition onto different substrates. Preparation parameters like precursors, chemical composition, solvents, thermal treatment factors (temperature, time, and atmosphere) were detailed studied. Finally, the resulting materials were characterized by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM) coupled with Energy dispersive X-ray analysis (EDAX), UV-VIS Spectroscopy among others.; key words: sol-gel synthesis, thin film deposition, photovoltaic modules, solar cells

Three-stage treatment protocol for recalcitrant distal femoral nonunion.

Science.gov (United States)

Ma, Ching-Hou; Chiu, Yen-Chun; Tu, Yuan-Kun; Yen, Cheng-Yo; Wu, Chin-Hsien

2017-04-01

In this study, we proposed a three-stage treatment protocol for recalcitrant distal femoral nonunion and aimed to analyze the clinical results. We retrospective reviewed 12 consecutive patients with recalcitrant distal femoral nonunion undergoing our three-stage treatment protocol from January 2010 to December 2014 in our institute. The three-stage treatment protocol comprised debridement of the nonunion site, lengthening to eliminate leg length discrepancy, deformity correction, stabilization with a locked plate, filling of the defect with cement spacer for inducing membrane formation, and bone reconstruction using a cancellous bone autograft (Masquelet technique) or free vascularized fibular bone graft. The bone union time, wound complication, lower limbs alignment, amount of lengthening, knee range of motion, and functional outcomes were evaluated. Osseous union with angular deformity lengthening was 5.88 cm (range 3.5-12 cm). Excellent or good outcomes were obtained in 9 patients. Although the current study involved only a small number of patients and the intervention comprised three stages, we believe that such a protocol may be a valuable alternative for the treatment of recalcitrant distal femoral nonunion.

Adhesion, resistivity and structural, optical properties of molybdenum on steel sheet coated with barrier layer done by sol–gel for CIGS solar cells

Energy Technology Data Exchange (ETDEWEB)

Amouzou, Dodji, E-mail: dodji.amouzou@fundp.ac.be [Research Centre in Physics of Matter and Radiation (PMR), University of Namur (FUNDP), Rue de Bruxelles 61, 5000 Namur (Belgium); Dumont, Jacques [Research Centre in Physics of Matter and Radiation (PMR), University of Namur (FUNDP), Rue de Bruxelles 61, 5000 Namur (Belgium); Fourdrinier, Lionel; Richir, Jean-Baptiste; Maseri, Fabrizio [CRM-Group, Boulevard de Colonster, B 57, 4000 Liège (Belgium); Sporken, Robert [Research Centre in Physics of Matter and Radiation (PMR), University of Namur (FUNDP), Rue de Bruxelles 61, 5000 Namur (Belgium)

2013-03-01

Molybdenum films are investigated on stainless steel substrates coated with polysilazane based sol–gel and SiO{sub x} layers for flexible CIGS solar cell applications. Thermal stability of the multilayer has been studied. The thickness of polysilazane films are significantly reduced (17%) after heat treatment suggesting a thermal degradation. Four different microstructures were found for Mo films by varying argon total pressure from 2.6 × 10{sup −1} Pa to 2.6 Pa. It was shown that continuous films, low sheet resistance (0.5 Ω/□) and well facetted grains can be achieved when Mo films are deposited on heated substrates at homologous temperature, T of 0.2. - Highlights: ► Steel sheet is functionalized for Cu[Inx,Ga(1 − x)Se2] solar cells. ► Varying deposition pressure impacts the microstructure of Mo films. ► High thermal stability of the sol gel based barrier layer has been investigated. ► Low sheet resistance and continuous Mo films have been obtained at 550°C. ► Thermal stability of functionalized steel sheets at 550°C has been investigated.

Competitive-IgY- Enzyme Linked Immuno Sorbent Assay (CIgY-ELISA to detect the cytokinins in Gerbera jamesonii plantlets

Directory of Open Access Journals (Sweden)

Cleiton Mateus Sousa

2011-08-01

Full Text Available A competitive hyper-immune yolk Immunoglobulin Y - Enzyme Linked Immune Sorbent Assay (CIgY-ELISA, was developed as an alternative method to detect zeatin and 2ip in plantlets of gerbera. The endogenous level of hormones in the plantlets in vitro of gerbera with one or six weeks after replication was determined with competitive IgY-ELISA set to detect between 1 and 100 pmoles of plant hormone for each 1.0 g tissue. The plantlets of six weeks presented sprouts and root, while the plantlets of one week presented only sprouts. The CIgY-ELISA was set with high independent variables values of sensitivity/specificity of 96/89 % for zeatin and 94/78 % for 2ip, with high values of reproducibility (up to 90 % for both the cytokinins. Zeatin content varied from 2.2 to 2.8 pmoles.g-1 and from 2.7 to 3.3 pmoles.g-1 on the plantlet with one and six weeks, respectively. The 2ip content did not vary and was detected near the detection limit in all the assays. It was concluded that the observed capabilities of CIgY-ELISA were putative and the competitive assay was a highly robust and stable method, which could be used for the studies on plant physiology for endogenous cytokinins.

Semi-transparent photovoltaic glazing based on electrodeposited CIGS solar cells on patterned molybdenum/glass substrates

Directory of Open Access Journals (Sweden)

Sidali Tarik

2018-01-01

Full Text Available In this paper, a new way of preparing semi-transparent solar cells using Cu(In1−xGaxSe2 (CIGS chalcopyrite semiconductors as absorbers for BIPV applications is presented. The key to the elaboration process consists in the co-electrodeposition of Cu-In-Ga mixed oxides on submillimetric hole-patterned molybdenum substrate, followed by thermal reduction to metallic alloys and selenisation. This method has the advantage of being a selective deposition technique where the thin film growth is carried out only on Mo covered areas. Thus, after annealing, the transparency of the sample is always preserved, allowing light to pass through the device. A complete device (5 × 5 cm2 with 535 μm diameter holes and total glass aperture of around 35% shows an open circuit voltage (VOC of 400 mV. Locally, the I-V curves reveal a maximum efficiency of 7.7%, VOC of 460 mV, JSC of 24 mA.cm−2 in an area of 0.1 cm2 with 35% aperture. This efficiency on the semi-transparent area is equivalent to a record efficiency of 11.9% by taking into account only the effective area.

The shear zone-related gold mineralization at the Turmalina deposit, Quadrilátero Ferrífero, Brazil: structural evolution and the two stages of mineralization

Science.gov (United States)

Fabricio-Silva, Wendell; Rosière, Carlos Alberto; Bühn, Bernhard

2018-05-01

Turmalina is an important orogenic gold deposit located in the NW region of the Quadrilátero Ferrífero. The deposit is hosted in an Archean greenstone belt composed of ortho-amphibolites and pelites with interleaved tuffs metamorphosed under amphibolite facies conditions and intruded by a granite stock. The orebodies are controlled by WNW-ESE-trending shear zones, associated with hydrothermal alteration. Three deformation events are recognized in the Turmalina gold deposit: D1 and D2 are the result of a progressive Archean deformation under ductile conditions between 2749 ± 7 and 2664 ± 35 Ma; D3 is characterized by a transpressional event under ductile-brittle conditions with the age still unclear. The three generations of garnet observed show that Grt1 blastesis is pre- to syn-D1 and Grt2 growth during the late to post-deformation stages of the D2 event. The initial temperature (Grt1 core) is around 548-600 °C, whereas during late D2, the temperatures reached 633 °C (metamorphic peak-Grt2 rim), likely as a result of granite intrusion. The Grt3 resulted from re-equilibration under retrograde conditions. Two gold-bearing sulfide stages were identified: pyrrhotite-arsenopyrite ± löllingite ± chalcopyrite ± gold stage I precipitated below a metamorphic peak temperature of 598 ± 19 °C associated with S1 foliation (D1), and pyrrhotite-pyrite-arsenopyrite ± chalcopyrite ± gold stage II is located commonly along V3 quartz-carbonate veinlets with a temperature range between 442 ± 9 and 510 ± 30 °C. We suggest that the granite intrusion imposed an additional thermal effect that promoted further dehydration of country rocks. The Au derived mainly from a metamorphic fluid source but potentially mixed with magmatic fluids from the granite.

Optimization of Three-stage Electromagnetic Coil Launcher

Directory of Open Access Journals (Sweden)

Yujiao Zhang

2014-05-01

Full Text Available For the design of three-stage electromagnetic coilgun, many parameters and their relations must be considered at the same time. However, there is no complete mathematical model to describe the relationship between these parameters and energy conversion efficiency of the coil launcher system. In this paper, using orthogonal test approach we consider the influence of 11 parameters to improve the energy conversion efficiency of a three-stage coilgun. Moreover, for the 11 parameters, another three neighboring values of the actual value are considered. According to the different 64 simulations arranged by orthogonal test approach, the 64 groups of muzzle velocity calculated by circuit equations can be analyzed to obtain a better parameters’ combination. For the solution of circuit simulations, an improved current filament method is proposed. To validate the optimal design, we manufacture the prototype and the improved one. The experimental results indicate that the optimal design method is effective.

Preparation of CIGS thin films by HiPIMS or DC sputtering and various selenization processes

Czech Academy of Sciences Publication Activity Database

Olejníček, Jiří; Hubička, Zdeněk; Kšírová, Petra; Kment, Štěpán; Brunclíková, Michaela; Kohout, Michal; Čada, Martin; Darveau, S.A.; Exstrom, C.L.

2013-01-01

Roč. 16, č. 2 (2013), s. 314-319 ISSN 1203-8407 R&D Projects: GA MŠk LH12045 Institutional support: RVO:68378271 Keywords : CIGS * HIPIMS * selenization * nanocrystals * solar energy * sputtering * thin films Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 1.106, year: 2013 http://www.ingentaconnect.com/content/stn/jaots/2013/00000016/00000002/art00015

Characterization of in-situ annealed sub-micron thick Cu(In,Ga)Se{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Ko, Byoung-Soo; Sung, Shi-Joon; Hwang, Dae-Kue, E-mail: dkhwang@dgist.ac.kr

2015-09-01

Sub-micron thick Cu(In,Ga)Se{sub 2} (CIGS) thin films were deposited on Mo-coated soda-lime glass substrates under various conditions by single-stage co-evaporation. Generally, the short circuit current (J{sub sc}) decreased with the decreasing thickness of the absorber layer. However, in this study, J{sub sc} was nearly unchanged with decreasing thickness, while the open circuit voltage (V{sub oc}) and fill factor (FF) decreased by 31.9 and 31.1%, respectively. We believe that the remarkable change of V{sub oc} and FF can be attributed to the difference in the total amount of injected thermal energy. Using scanning electron microscopy, we confirmed that the surface morphology becomes smooth and the grain size increased after the annealing process. In the X-ray diffraction patterns, the CIGS thin film also showed an improved crystal quality. We observed that the electric properties were improved by the in-situ annealing of CIGS thin films. The reverse saturation current density of the annealed CIGS solar cell was 100 times smaller than that of reference solar cell. Thus, sub-micron CIGS thin films annealed under a constant Se rate showed a 64.7% improvement in efficiency. - Highlights: • The effects of in-situ annealing the sub-micron CIGS film have been investigated. • The surface morphology and the grain size were improved by in-situ annealing. • The V{sub oc} and FF of the films were increased by about 30% after in-situ annealing. • In-situ annealing of sub-micron thick CIGS films can be improved an efficiency.

Effect of Electrodeposition Potential on Composition of CuIn1−xGaxSe2 Absorber Layer for Solar Cell by One-Step Electrodeposition

Directory of Open Access Journals (Sweden)

Rui-Wei You

2014-01-01

Full Text Available CIGS polycrystalline thin films were successfully fabricated by one-step cathodic electrodeposition on Mo-coated glass. In this study, we applied a galvanometry mode with three-electrode potentiostatic systems to produce a constant concentration electroplating solution, which were composed of CuCl2, InCl3, GaCl3, and SeO2. Then these as-electrodeposited films were annealed in argon atmosphere and characterized by X-ray diffraction. The results revealed that annealing treatment significantly improved the crystallinity of electrodeposited films and formed CIGS chalcopyrite structure, but at low applied deposition voltage (−950 mV versus SCE there appeared second phase. The cross-section morphology revealed that applied voltage at −1350 mV versus SCE has uniform deposition, and higher applied voltage made grain more unobvious. The deposition rate and current density are proportional to deposition potential, and hydrogen was generated apparently when applying potential beyond −1750 mV versus SCE. It was found that the CIGS compound did not match exact stoichiometry of Cu : In : Ga : Se =1 : x : 1-x : 2. This result suggests the possibility of controlling the property of thin films by varying the applied potential during electrodeposition.

Stages of change in audiology: comparison of three self-assessment measures.

Science.gov (United States)

Ingo, Elisabeth; Brännström, K Jonas; Andersson, Gerhard; Lunner, Thomas; Laplante-Lévesque, Ariane

2017-07-01

In a clinical setting, theories of health behaviour change could help audiologists and other hearing health care professionals understand the barriers that prevent people with hearing problems to seek audiological help. The transtheoretical (stages of change) model of health behaviour change is one of these theories. It describes a person's journey towards health behaviour change (e.g. seeking help or taking up rehabilitation) in separate stages: precontemplation, contemplation, preparation, action, and, finally, maintenance. A short self-assessment measure of stages of change may guide the clinician and facilitate first appointments. This article describes correlations between three stages of change measures of different lengths, one 24-item and two one-item. Participants were recruited through an online hearing screening study. Adults who failed the speech-in-noise recognition screening test and who had never undergone a hearing aid fitting were invited to complete further questionnaires online, including the three stages of change measures. In total, 224 adults completed the three measures. A majority of the participants were categorised as being in one of the information- and help-seeking stage of change (contemplation or preparation). The three stages of change measures were significantly correlated. Conclusions Our results support further investigating the use of a one-item measure to determine stages of change in people with hearing impairment.

Optical Design of Textured Thin-Film CIGS Solar Cells with Nearly-Invisible Nanowire Assisted Front Contacts

Directory of Open Access Journals (Sweden)

Joop van Deelen

2017-04-01

Full Text Available The conductivity of transparent front contacts can be improved by patterned metallic nanowires, albeit at the cost of optical loss. The associated optical penalty can be strongly reduced by texturization of the cell stack. Remarkably, the nanowires themselves are not textured and not covered in our design. This was shown by optical modeling where the width of the nanowire, the texture height and the texture period were varied in order to obtain a good insight into the general trends. The optical performance can be improved dramatically as the reflection, which is the largest optical loss, can be reduced by 95% of the original value. The spectra reveal absorption in the Cu(In,GaSe2 (CIGS layer of 95% and reflection below 2% over a large part of the spectrum. In essence, a virtually black CIGS cell stack can be achieved for textured cells with a metal nanogrid. Moreover, it turned out that the ratio between the width of the nanowire and the height of the texture is a critical parameter for optical losses.

Effects of Sb-doping on the grain growth of Cu(In, Ga)Se2 thin films fabricated by means of single-target sputtering

International Nuclear Information System (INIS)

Zhang, Shu; Wu, Lu; Yue, Ruoyu; Yan, Zongkai; Zhan, Haoran; Xiang, Yong

2013-01-01

To investigate the effects of Sb doping on the kinetics of grain growth in Cu(In,Ga)Se 2 (CIGS) thin films during annealing, CIGS thin films were sputtered onto Mo coated substrates from a single CIGS alloy target, followed by chemical bath deposition of Sb 2 S 3 thin layers on top of CIGS layers and subsequent annealing at different temperatures for 30 min in Se vapors. X-ray diffraction results showed that CIGS thin films were obtained directly using the single-target sputtering method. After annealing, the In/Ga ratio in Sb-doped CIGS thin films remained stable compared to undoped film, possibly because Sb can promote the incorporation of Ga into CIGS. The grain growth in CIGS thin films was enhanced after Sb doping, exhibiting significantly larger grains after annealing at 400 °C or 450 °C compared to films without Sb. In particular, the effect was strikingly significant in grain growth across the film thickness, resulting in columnar grain structure in Sb-doped films. This grain growth improvement may be led by the diffusion of Sb from the front surface to the CIGS-Mo back interface, which promoted the mass transport process in CIGS thin films. - Highlights: ► Cu(In,Ga)Se 2 (CIGS) thin films made by sputtering from a single CIGS target. ► Chemical bath deposition used to introduce antimony into CIGS absorber layers. ► In/Ga ratio decreases in Sb-doped annealed films, comparatively to undoped films. ► Sb-doped CIGS films are superior to undoped films in terms of grain-growth kinetics

Controlling the physical parameters of crystalline CIGS nanowires for use in superstrate configuration using vapor phase epitaxy

Science.gov (United States)

Lee, Dongjin; Jeon, H. C.; Kang, T. W.; Kumar, Sunil

2018-03-01

Indium tin oxide (ITO) is a suitable candidate for smart windows and bifacial semi-transparent solar cell applications. In this study, highly crystalline CuInGaSe2 (CIGS) nanowires were successfully grown by horizontal-type vapor phase epitaxy on an ITO substrate. Length, diameter, and density of the nanowires were studied by varying the growth temperature (500, 520, and 560 °C), time (3.5, 6.5, and 9.5 h), and type of catalyst (In, Au, and Ga). Length, diameter, and density of the nanowires were found to be highly dependent on the growth conditions. At an optimized growth period and temperature of 3.5 h and 520 °C, respectively, the length and diameter of the nanowires were found to increase when grown in a catalyst-free environment. However, the density of the nanowires was found to be higher while using a catalyst during growth. Even in a catalyst-free environment, an Indium cluster formed at the bottom of the nanowires. The source of these nanowires is believed to be Indium from the ITO substrate which was observed in the EDS measurement. TEM-based EDS and line EDS indicated that the nanowires are made up of CIGS material with a very low Gallium content. XRD measurements also show the appearance of wurtzite CIS nanowires grown on ITO in addition to the chalcopyrite phase. PL spectroscopy was done to see the near-band-edge emission for finding band-to-band optical transition in this material. Optical response of the CIGS nanowire network was also studied to see the photovoltaic effect. This work creates opportunities for making real solar cell devices in superstrate configuration.

Enhanced electrical properties of pulsed laser-deposited CuIn{sub 0.7}Ga{sub 0.3}Se{sub 2} thin films via processing control

Energy Technology Data Exchange (ETDEWEB)

Jo, Yeon Hwa; Mohanty, Bhaskar Chandra; Cho, Yong Soo [Department of Materials Science and Engineering, Yonsei University, Seoul (Korea, Republic of)

2010-12-15

Polycrystalline CuIn{sub 0.7}Ga{sub 0.3}Se{sub 2} thin films were prepared on soda-lime glass substrates using pulsed laser deposition (PLD) with various process parameters such as laser energy, repetition rate and substrate temperature. It was confirmed that there existed a limited laser energy, i.e. less than 300 mJ, to get phase pure CIGS thin films at room temperature. Particularly, even at room temperature, distinct crystalline CIGS phase was observed in the films. Crystallinity of the films improved with increasing substrate temperature as evidenced by the decrease of FWHM from 0.65 degto 0.54 deg. Slightly Cu-rich surface with Cu{sub 2-x}Se phase was confirmed to exist by Raman spectra, depending on substrate temperature. Improved electrical properties, i.e., carrier concentration of {proportional_to}10{sup 18} cm{sup -3} and resistivity of 10{sup -1}{omega} cm at higher substrate temperature for the optimal CIGS films are assumed to be induced by the potential contributions from highly crystallized thin films, existence of Cu{sub 2-x}Se phase and diffusion of Na from substrates to films. (author)

Three-Stage Quantum Cryptography Protocol under Collective-Rotation Noise

Directory of Open Access Journals (Sweden)

Linsen Wu

2015-05-01

Full Text Available Information security is increasingly important as society migrates to the information age. Classical cryptography widely used nowadays is based on computational complexity, which means that it assumes that solving some particular mathematical problems is hard on a classical computer. With the development of supercomputers and, potentially, quantum computers, classical cryptography has more and more potential risks. Quantum cryptography provides a solution which is based on the Heisenberg uncertainty principle and no-cloning theorem. While BB84-based quantum protocols are only secure when a single photon is used in communication, the three-stage quantum protocol is multi-photon tolerant. However, existing analyses assume perfect noiseless channels. In this paper, a multi-photon analysis is performed for the three-stage quantum protocol under the collective-rotation noise model. The analysis provides insights into the impact of the noise level on a three-stage quantum cryptography system.

Deposition behavior of colloid in filtration process through glass beads packed bed

International Nuclear Information System (INIS)

Chinju, Hirofumi; Nagasaki, Shinya; Tanaka, Satoru; Tanaka, Tadao; Takebe, Shinichi; Ogawa, Hiromichi

1999-01-01

We investigated the deposition behavior in colloid transport through porous media by conducting column experiments and batch experiments using polystyrene latex particles and spherical glass beads. The conclusion of this present work are summarized as follows: (1) The comparison between the results of the batch and the column experiments indicated that the deposition was enhanced in the column experiments compared with the batch experiments due to particles trapped by the effect of slow field. (2) Colloid BTCs showed three different stages of deposition which can be characterized by the different rate of the change in the C/C O . Three stages can be explained by the existence of large area of weak deposition sites and small area of strong deposition sites on the collector surfaces. (3) The amount of deposited particles until the beginning of the third stage was larger for lower flow velocity. (4) The results of the column experiments revealed that breakthrough behavior of colloidal particles of the second run after back wash process is affected by remaining particles on collector surfaces. (J.P.N.)

The effect of damp heat-illumination exposure on CIGS solar cells: A combined XRD and electrical characterization study

NARCIS (Netherlands)

Theelen, M.; Hendrikx, R.; Barreau, N.; Steijvers, H.; Böttger, A.

2016-01-01

Unencapsulated CIGS solar cells were simultaneously exposed to damp heat and illumination. In-situ monitoring of their electrical parameters demonstrated a rapid decrease of the efficiency, mainly driven by changes in the series and shunt resistances. The non-degraded and degraded solar cells were

Modelling Defects Acceptors And Determination Of Electric Model From The Nyquist Plot And Bode In Thin Film CIGS

Directory of Open Access Journals (Sweden)

Demba Diallo

2015-08-01

Full Text Available Abstract The performance of the chalcopyrite material CuInGaSe2 CIGS used as an absorber layer in thin-film photovoltaic devices is significantly affected by the presence of native defects. Multivalent defects e.g. double acceptors or simple acceptor are important immaterial used in solar cell production in general and in chalcopyrite materials in particular. We used the thin film solar cell simulation software SCAPS to enable the simulation of multivalent defects with up to five different charge states.Algorithms enabled us to simulate an arbitrary number of possible states of load. The presented solution method avoids numerical inaccuracies caused by the subtraction of two almost equal numbers. This new modelling facility is afterwards used to investigate the consequences of the multivalent character of defects for the simulation of chalcopyrite based CIGS. The capacitance increase with the evolution of the number of defects C- f curves have found to have defect dependence.

Influence of growth temperature of transparent conducting oxide layer on Cu(In,Ga)Se2 thin-film solar cells

International Nuclear Information System (INIS)

Cho, Dae-Hyung; Chung, Yong-Duck; Lee, Kyu-Seok; Park, Nae-Man; Kim, Kyung-Hyun; Choi, Hae-Won; Kim, Jeha

2012-01-01

We have studied the influence of growth temperature (T G ) in the deposition of an indium tin oxide (ITO) transparent conducting oxide layer on Cu(In,Ga)Se 2 (CIGS) thin-film solar cells. The ITO films were deposited on i-ZnO/glass and i-ZnO/CdS/CIGS/Mo/glass substrates using radio-frequency magnetron sputtering at various T G up to 350 °C. Both the resistivity of ITO and the interface quality of CdS/CIGS strongly depend on T G . For a T G ≤ 200 °C, a reduction in the series resistance enhanced the solar cell performance, while the p–n interface of the device was found to become deteriorated severely at T G > 200 °C. CIGS solar cells with ITO deposited at T G = 200 °C showed the best performance in terms of efficiency.

The influence of different locations of sputter guns on the morphological and structural properties of Cu–In–Ga precursors and Cu(In,Ga)Se{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Wang, J.; Zhu, J., E-mail: jiezhu@ustb.edu.cn; He, Y.X.

2014-01-01

The influence of two different locations of sputter guns on the morphological and structural properties of Cu–In–Ga precursors and Cu(In,Ga)Se{sub 2} (CIGS) thin films was investigated. All the precursors contained cauliflower-like nodules, whereas smaller subnodules were observed on the background. All the precursors revealed apparent three-layered structures, and voids were observed at the CIGS/SLG interface of Sets 1 and 2 films rather than Set 3 film. EDS results indicated that all CIGS thin films were Cu-deficient. Based on the grazing incidence X-ray diffraction (GIXRD) patterns, as-selenized films showed peaks corresponding to the chalcopyrite-type CIGS structure. Depth-resolved Raman spectra showed the formation of a dominant CIGS phase inside the films for all the as-selenized samples investigated, and of an ordered vacancy compound (OVC) phase like Cu(In,Ga){sub 3}Se{sub 5} or Cu(In,Ga){sub 2}Se{sub 3.5} at the surface and/or CIGS/SLG interface region of Sets 2 and 3 films. No evidence was obtained on the presence of an OVC phase in Set 1 CIGS film, which may be speculated that long-time annealing is contributed to suppress the growth of OVC phases. The results of the present work suggest that the metallic precursors deposited with the upright-location sputter gun might be more appropriate to prepare CIGS thin films than those sputtered with the titled-location gun.

Inkjet printed Cu(In,Ga)S{sub 2} nanoparticles for low-cost solar cells

Energy Technology Data Exchange (ETDEWEB)

Barbé, Jérémy, E-mail: jeremy.barbe@kaust.edu.sa; Eid, Jessica [King Abdullah University of Science and Technology, Solar and Photovoltaics Engineering Research Center (SPERC), Division of Physical Sciences and Engineering (Saudi Arabia); Ahlswede, Erik; Spiering, Stefanie; Powalla, Michael [Zentrum fur Sonnenenergie- und Wasserstoff-Forschung Baden-Württemberg (ZSW) (Germany); Agrawal, Rakesh [Purdue University, School of Chemical Engineering (United States); Del Gobbo, Silvano, E-mail: silvano.delgobbo@gmail.com [King Abdullah University of Science and Technology, Solar and Photovoltaics Engineering Research Center (SPERC), Division of Physical Sciences and Engineering (Saudi Arabia)

2016-12-15

Cu(In,Ga)Se{sub 2} (CIGSe) thin film solar cells were fabricated by direct inkjet printing of Cu(In,Ga)S{sub 2} (CIGS) nanoparticles followed by rapid thermal annealing under selenium vapor. Inkjet printing is a low-cost, low-waste, and flexible patterning method which can be used for deposition of solution-based or nanoparticle-based CIGS films with high throughput. XRD and Raman spectra indicate that no secondary phase is formed in the as-deposited CIGS film since quaternary chalcopyrite nanoparticles are used as the base solution for printing. Besides, CIGSe films with various Cu/(In + Ga) ratios could be obtained by finely tuning the composition of CIGS nanoparticles contained in the ink, which was found to strongly influence the devices performance and film morphology. To date, this is the first successful fabrication of a solar device by inkjet printing of CIGS nanoparticles.

Inkjet printed Cu(In,Ga)S2 nanoparticles for low-cost solar cells

KAUST Repository

Barbe, Jeremy

2016-12-13

Cu(In,Ga)Se2 (CIGSe) thin film solar cells were fabricated by direct inkjet printing of Cu(In,Ga)S2 (CIGS) nanoparticles followed by rapid thermal annealing under selenium vapor. Inkjet printing is a low-cost, low-waste, and flexible patterning method which can be used for deposition of solution-based or nanoparticle-based CIGS films with high throughput. XRD and Raman spectra indicate that no secondary phase is formed in the as-deposited CIGS film since quaternary chalcopyrite nanoparticles are used as the base solution for printing. Besides, CIGSe films with various Cu/(In + Ga) ratios could be obtained by finely tuning the composition of CIGS nanoparticles contained in the ink, which was found to strongly influence the devices performance and film morphology. To date, this is the first successful fabrication of a solar device by inkjet printing of CIGS nanoparticles.

Seafloor Topographic Analysis in Staged Ocean Resource Exploration

Science.gov (United States)

Ikeda, M.; Okawa, M.; Osawa, K.; Kadoshima, K.; Asakawa, E.; Sumi, T.

2017-12-01

J-MARES (Research and Development Partnership for Next Generation Technology of Marine Resources Survey, JAPAN) has been designing a low-expense and high-efficiency exploration system for seafloor hydrothermal massive sulfide deposits in "Cross-ministerial Strategic Innovation Promotion Program (SIP)" granted by the Cabinet Office, Government of Japan since 2014. We designed a method to focus mineral deposit prospective area in multi-stages (the regional survey, semi-detail survey and detail survey) by extracted topographic features of some well-known seafloor massive sulfide deposits from seafloor topographic analysis using seafloor topographic data acquired by the bathymetric survey. We applied this procedure to an area of interest more than 100km x 100km over Okinawa Trough, including some known seafloor massive sulfide deposits. In Addition, we tried to create a three-dimensional model of seafloor topography by SfM (Structure from Motion) technique using multiple image data of Chimney distributed around well-known seafloor massive sulfide deposit taken with Hi-Vision camera mounted on ROV in detail survey such as geophysical exploration. Topographic features of Chimney was extracted by measuring created three-dimensional model. As the result, it was possible to estimate shape of seafloor sulfide such as Chimney to be mined by three-dimensional model created from image data taken with camera mounted on ROV. In this presentation, we will discuss about focusing mineral deposit prospective area in multi-stages by seafloor topographic analysis using seafloor topographic data in exploration system for seafloor massive sulfide deposit and also discuss about three-dimensional model of seafloor topography created from seafloor image data taken with ROV.

A novel three-stage distance-based consensus ranking method

Science.gov (United States)

Aghayi, Nazila; Tavana, Madjid

2018-05-01

In this study, we propose a three-stage weighted sum method for identifying the group ranks of alternatives. In the first stage, a rank matrix, similar to the cross-efficiency matrix, is obtained by computing the individual rank position of each alternative based on importance weights. In the second stage, a secondary goal is defined to limit the vector of weights since the vector of weights obtained in the first stage is not unique. Finally, in the third stage, the group rank position of alternatives is obtained based on a distance of individual rank positions. The third stage determines a consensus solution for the group so that the ranks obtained have a minimum distance from the ranks acquired by each alternative in the previous stage. A numerical example is presented to demonstrate the applicability and exhibit the efficacy of the proposed method and algorithms.

Three stage Kondo effect in a three quantum dot system

Science.gov (United States)

Chiappe, Guillermo; Costa Ribeiro, Laercio; Hamad, Ignacio; Victoriano Anda, Enrique

2014-03-01

In this work we study the transport properties of a series connected three quantum dot (QD) system with local strong Coulomb interaction and with one of the extremity QD connected to two metallic leads. We evaluate the local density of states (LDOS) in the QDs and the conductance between the metallic leads considering different magnitudes for the coupling between the central and the extremity QD which is not connected to the leads (side QDs). For small magnitudes of this coupling the LDOS of the QD coupled to the leads present a Kondo resonance with a dip and a very tiny peak at the Fermi level. The widths of these structures are associated to three energy scales, or three Kondo temperatures, which characterizes the three stage Kondo regime. Increasing the coupling between the side QDs we observe a transition to the conventional Kondo regime. We use the multi-configuration Lanczos calculations and the finite U slave-boson mean-field theory. The results present qualitative and quantitative agreement.

Cu(InGa)Se{sub 2} absorber formation by in-situ, low-temperature annealing of co-evaporated bilayer (InGa){sub 2}Se{sub 3}/CuSe precursors

Energy Technology Data Exchange (ETDEWEB)

Moon, Kyeongchan; Kim, Woo Kyoung, E-mail: wkim@ynu.ac.kr

2015-12-01

Chalcopyrite Cu(InGa)Se{sub 2} (CIGS) absorbers were fabricated by the formation of bilayer stacked glass/Mo/(InGa){sub 2}Se{sub 3}/CuSe precursors followed by in-situ thermal annealing at 450 °C for approximately 10 min in a vacuum evaporator. The material properties (e.g., crystal orientation, compositional depth profile, and overall composition) and device performance of the resulting CIGS absorbers were compared with those of the CIGS absorbers formed by conventional 1-stage and 3-stage CIGS formation processes at a similar temperature. X-ray diffraction confirmed that the 1-stage co-evaporation and in-situ annealing of the bilayer precursor produced a polycrystalline CIGS absorber without a specific texture, whereas the CIGS absorber formed by the 3-stage process showed a highly (220) preferred orientation. Secondary ion mass spectrometry revealed Ga accumulation at the bottom of CIGS formed by in-situ annealing of the bilayer precursors. The cell efficiency of the device with the CIGS absorber formed by the in-situ, low-temperature (450 °C) annealing of bilayer stacked glass/Mo/(InGa){sub 2}Se{sub 3}/CuSe precursors was comparable to that produced by the conventional 3-stage process at a similar temperature. - Highlights: • Annealing of (InGa){sub 2}Se{sub 3}/CuSe precursors was compared with coevaporation process. • In-situ annealing of (InGa){sub 2}Se{sub 3}/CuSe precursors at 450 °C produced about 9% solar cell. • Ga profile within Cu(InGa)Se{sub 2} depended on process profile during co-evaporation.

Ash Deposition Trials at Three Power Stations in Denmark

DEFF Research Database (Denmark)

Laursen, Karin; Frandsen, Flemming; Larsen, Ole Hede

1998-01-01

Six full-scale trials were conducted at three power stations in Denmark: Ensted, Funen, and Vendsyssel power stations. During these trials, pulverized coal, bottom ash, fly ash, and deposits from cooled probes were sampled and analyzed with various techniques. On the basis of SEM analyses...

Lung Toxicity of Condensed Aerosol from E-CIG Liquids: Influence of the Flavor and the In Vitro Model Used

Directory of Open Access Journals (Sweden)

Rossella Bengalli

2017-10-01

Full Text Available The diffusion of e-cigarette (e-CIG opens a great scientific and regulatory debate about its safety. The huge number of commercialized devices, e-liquids with almost infinite chemical formulations and the growing market demand for a rapid and efficient toxicity screen system that is able to test all of these references and related aerosols. A consensus on the best protocols for the e-CIG safety assessment is still far to be achieved, since the huge number of variables characterizing these products (e.g., flavoring type and concentration, nicotine concentration, type of the device, including the battery and the atomizer. This suggests that more experimental evidences are needed to support the regulatory frameworks. The present study aims to contribute in this field by testing the effects of condensed aerosols (CAs from three main e-liquid categories (tobacco, mint, and cinnamon as food-related flavor, with (18 mg/mL or without nicotine. Two in vitro models, represented by a monoculture of human epithelial alveolar cells and a three-dimensional (3D co-culture of alveolar and lung microvascular endothelial cells were used. Cell viability, pro-inflammatory cytokines release and alveolar-blood barrier (ABB integrity were investigated as inhalation toxicity endpoints. Results showed that nicotine itself had almost no influence on the modulation of the toxicity response, while flavor composition did have. The cell viability was significantly decreased in monoculture and ABB after exposure to the mints and cinnamon CAs. The barrier integrity was significantly affected in the ABB after exposure to cytotoxic CAs. With the exception of the significant IL-8 release in the monoculture after Cinnamon exposure, no increase of inflammatory cytokines (IL-8 and MCP-1 release was observed. These findings point out that multiple assays with different in vitro models are able to discriminate the acute inhalation toxicity of CAs from liquids with different flavors

Effects of NaF evaporation during low temperature Cu(In,Ga)Se{sub 2} growth

Energy Technology Data Exchange (ETDEWEB)

Bissig, B., E-mail: benjamin.bissig@empa.ch; Reinhard, P.; Pianezzi, F.; Hagendorfer, H.; Nishiwaki, S.; Buecheler, S.; Tiwari, A.N.

2015-05-01

Co-evaporation of NaF during the 3{sup rd} stage of the low temperature Cu(In,Ga)Se{sub 2} multi-stage process is compared to post-deposition treatment (PDT) with NaF in view of their influence on the electronic and structural properties. In case of NaF co-evaporation, quantum efficiency losses in the near infrared region and thus lower short circuit current density cause a reduced efficiency compared to solar cells prepared with NaF PDT. The formation of a deep defect with activation energy of ~ 250 meV is measured by capacitance spectroscopy and can explain the deteriorated performance in such devices. In addition, NaF co-evaporation during the 3{sup rd} stage causes reduced grain size in the top part of Cu(In,Ga)Se{sub 2} and altered In, Ga, and Cu distribution. - Highlights: • NaF was co-evaporated in a low temperature CIGS process during and after the 3rd stage. • CIGS grains size is reduced in the top 300 nm when NaF is co-evaporated. • C-f measurements indicate deep defect formation when NaF is co-evaporated.

Ore reserve estimation of uranium deposit Zirovski vrh

International Nuclear Information System (INIS)

Lukacs, E.

1979-01-01

The uranium ore deposit Zirovski vrh is in the Permian sediments of Northwest Yugoslavia. Lenticular bodies occur at several stratiform levels in grey, medium-grained sandstone. The ore deposit will be mined entirely by underground methods. It is possible to define three stages of deposit evaluation requiring different densities of exploration effort: preliminary evaluation of in situ ore reserves; evaluation of mineable ore reserves; evaluation of production capability and mine planning. The drilling density increases markedly with each succeeding stage. The optimal drilling density for all three stages of evaluation should be determined, but there is some concern that too close spaced drilling would considerably increase the exploration costs without a corresponding increase in effectiveness. On the other hand, too sparsely spaced drilling may result in some difficulties in following the ore in mining. The paper treats the problem of the density of drilling for evaluation of mineable ore reserves compared to that required for mine planning and mine production capability. The purpose of investigation of mineral raw materials is to define economic deposits (ore bodies). To evaluate the deposit economically an accurate reserve estimate is required. If it is accordingly established that such an estimate is within the degree of admissible error, the purpose of the exploration is satisfied. However, the problem as to whether the drilling grid is sufficiently dense remains, because the majority of estimates of ore reserves do not provide a measure of the reliability of the estimate. (author)

Analysis on the Performance of Copper Indium Gallium Selenide (CIGS Based Photovoltaic Thermal

Directory of Open Access Journals (Sweden)

Zulkepli Afzam

2016-01-01

Full Text Available This paper deals with the efficiency improvement of Copper Indium Gallium Selenide (CIGS Photovoltaic (PV and also solar thermal collector. Photovoltaic thermal (PV/T can improve overall efficiency for PV and also solve the problem of limited roof space at urban area. Objective of this study is to clarify the effect of mass flow rate on the efficiency of the PV/T system. A CIGS solar cell is used with rated output power 65 W and 1.18 m2 of area. 4 set of experiments were carried out, which were: thermal collector with 0.12 kg/s flow rate, PV/T with 0.12 kg/s flow rate, PV/T with 0.09 kg/s flow rate and PV. It was found that PV/T with 0.12 kg/s flow rate had the highest electrical efficiency, 2.92 %. PV/T with 0.09 kg/s flow rate had the lowest electrical efficiency, 2.68 %. It also had 2 % higher overall efficiency. The efficiency gained is low due to several factors. The rated output power of the PV is low for the area of 1.18 m2. The packing factor of the PV also need to be considered as it may not be operated at the optimal packing factor. Furthermore, aluminium sheet of the PV may affect the PV temperature due to high thermal conductivity. Further study on more values of mass flow rate and also other parameters that affect the efficiency of the PV/T is necessary.

Carbon- and oxygen-free Cu(InGa)(SSe)₂ solar cell with a 4.63% conversion efficiency by electrostatic spray deposition.

Science.gov (United States)

Yoon, Hyun; Na, Seung Heon; Choi, Jae Young; Kim, Min Woo; Kim, Hayong; An, Hee Sang; Min, Byoung Koun; Ahn, SeJin; Yun, Jae Ho; Gwak, Jihye; Yoon, KyungHoon; Kolekar, Sanjay S; van Hest, Maikel F A M; Al-Deyab, Salem S; Swihart, Mark T; Yoon, Sam S

2014-06-11

We have demonstrated the first example of carbon- and oxygen-free Cu(In,Ga)(SSe)2 (CIGSSe) absorber layers prepared by electrospraying a CuInGa (CIG) precursor followed by annealing, sulfurization, and selenization at elevated temperature. X-ray diffraction and scanning electron microscopy showed that the amorphous as-deposited (CIG) precursor film was converted into polycrystalline CIGSSe with a flat-grained morphology after post-treatment. The optimal post-treatment temperature was 300 °C for annealing and 500 °C for both sulfurization and selenization, with a ramp rate of 5 °C/min. The carbon impurities in the precursor film were removed by air annealing, and oxide that was formed during annealing was removed by sulfurization. The fabricated CIGSSe solar cell showed a conversion efficiency of 4.63% for a 0.44 cm(2) area, with Voc = 0.4 V, Jsc = 21 mA/cm(2), and FF = 0.53.

Ternary Precursors for Depositing I-III-VI2 Thin Films for Solar Cells via Spray CVD

Science.gov (United States)

Banger, K. K.; Hollingsworth, J. A.; Jin, M. H.-C.; Harris, J. D.; Duraj, S. A.; Smith, M.; Scheiman, D.; Bohannan, E. W.; Switzer, J. A.; Buhro, W. E.

2002-01-01

The development of thin-film solar cells on flexible, lightweight, space-qualified substrates provides an attractive cost solution to fabricating solar arrays with high specific power (W/kg). Thin-film fabrication studies demonstrate that ternary single source precursors (SSP's) can be used in either a hot or cold-wall spray chemical vapour deposition (CVD) reactor, for depositing CuInS2, CuGaS2, and CuGaInS2 at reduced temperatures (400 to 450 C), which display good electrical and optical properties suitable for photovoltaic (PV) devices. X-ray diffraction studies, energy dispersive spectroscopy (EDS), and scanning electron microscopy (SEM) confirmed the formation of the single phase CIS, CGS, CIGS thin-films on various substrates at reduced temperatures.

Photovoltaic characterization of Copper-Indium-Gallium Sulfide (CIGS2) solar cells for lower absorber thicknesses

Energy Technology Data Exchange (ETDEWEB)

Vasekar, Parag S., E-mail: psvasekar@yahoo.co [Florida Solar Energy Center, 1679 Clearlake Rd., Cocoa FL, 32922 (United States); Jahagirdar, Anant H.; Dhere, Neelkanth G. [Florida Solar Energy Center, 1679 Clearlake Rd., Cocoa FL, 32922 (United States)

2010-01-31

Chalcopyrites are important contenders among thin-film solar cells due to their direct band gap and higher absorption coefficient. Copper-Indium-Gallium Sulfide (CIGS2) is a chalcopyrite material with a near-optimum band gap of {approx} 1.5 eV. Record efficiency of 11.99% has been achieved on a 2.7 {mu}m CIGS2 film prepared by sulfurization at the Florida Solar Energy Center (FSEC) PV Materials Lab. In this work, photovoltaic performance analysis has been carried out for a 1.5 {mu}m absorber prepared under similar conditions as that of a 2.7 {mu}m thick absorber sample. It was observed that there is an increase in diode factor and reverse saturation current density when the absorber thickness was decreased. The diode factor increased from 1.69 to 2.18 and reverse saturation current density increased from 1.04 x 10{sup -10} mA/cm{sup 2} to 1.78 x 10{sup -8} mA/cm{sup 2}. This can be attributed to a decrease in the grain size when the absorber thickness is decreased. It was also observed that there is an improvement in the shunt resistance. Improvement in shunt resistance can be attributed to optimized value of i:ZnO for lower absorber thickness and less shunting paths due to a smoother absorber.

Photovoltaic characterization of Copper-Indium-Gallium Sulfide (CIGS2) solar cells for lower absorber thicknesses

International Nuclear Information System (INIS)

Vasekar, Parag S.; Jahagirdar, Anant H.; Dhere, Neelkanth G.

2010-01-01

Chalcopyrites are important contenders among thin-film solar cells due to their direct band gap and higher absorption coefficient. Copper-Indium-Gallium Sulfide (CIGS2) is a chalcopyrite material with a near-optimum band gap of ∼ 1.5 eV. Record efficiency of 11.99% has been achieved on a 2.7 μm CIGS2 film prepared by sulfurization at the Florida Solar Energy Center (FSEC) PV Materials Lab. In this work, photovoltaic performance analysis has been carried out for a 1.5 μm absorber prepared under similar conditions as that of a 2.7 μm thick absorber sample. It was observed that there is an increase in diode factor and reverse saturation current density when the absorber thickness was decreased. The diode factor increased from 1.69 to 2.18 and reverse saturation current density increased from 1.04 x 10 -10 mA/cm 2 to 1.78 x 10 -8 mA/cm 2 . This can be attributed to a decrease in the grain size when the absorber thickness is decreased. It was also observed that there is an improvement in the shunt resistance. Improvement in shunt resistance can be attributed to optimized value of i:ZnO for lower absorber thickness and less shunting paths due to a smoother absorber.

Role of the buffer solution in the chemical deposition of CdS films for CIGS solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Lee, Sooho; Kim, Donguk; Baek, Dohyun; Hong, Byoungyou; Yi, Junsin; Lee, Jaehyeong [Sungkyunkwan University, Suwon (Korea, Republic of); Park, Yongseob [Chosun College of Science and and Technology, Gwangju (Korea, Republic of); Choi, Wonseok [Hanbat National University, Daejeon (Korea, Republic of)

2014-05-15

In this work, the effects of NH{sub 4}Ac on the structural and the electro-optical properties of CdS films were investigated. CdS thin films were deposited on soda-lime glass and indium-tin-oxide (ITO) coated glass from a chemical bath containing 0.025 M cadmium acetate, 0 M ∼ 0.2 M ammonium acetate, 0.5 M thiourea, and ammonia. Cadmium acetate was the cadmium source, ammonium acetate served as a buffer, ammonia was the complexing agent, and thiourea was the source of sulfur. A commonly- available chemical bath deposition system was successfully modified to obtain precise control over the pH of the solution at 75 .deg. C during the deposition. Chemically deposited CdS films were studied by using field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), optical transmittance, and electrical resistivity measurements.

Processing of CuInSe{sub 2}-based solar cells: Characterization of deposition processes in terms of chemical reaction analyses. Phase 2 Annual Report, 6 May 1996--5 May 1997

Energy Technology Data Exchange (ETDEWEB)

Anderson, T.

1999-10-20

This report describes research performed by the University of Florida during Phase 2 of this subcontract. First, to study CIGS, researchers adapted a contactless, nondestructive technique previously developed for measuring photogenerated excess carrier lifetimes in SOI wafers. This dual-beam optical modulation (DBOM) technique was used to investigate the differences between three alternative methods of depositing CdS (conventional chemical-bath deposition [CBD], metal-organic chemical vapor deposition [MOCVD], and sputtering). Second, a critical assessment of the Cu-In-Se thermochemical and phase diagram data using standard CALPHAD procedures is being performed. The outcome of this research will produce useful information on equilibrium vapor compositions (required annealing ambients, Sex fluxes from effusion cells), phase diagrams (conditions for melt-assisted growth), chemical potentials (driving forces for diffusion and chemical reactions), and consistent solution models (extents of solid solutions and extending phase diagrams). Third, an integrated facility to fabricate CIS PV devices was established that includes migration-enhanced epitaxy (MEE) for deposition of CIS, a rapid thermal processing furnace for absorber film formation, sputtering of ZnO, CBD or MOCVD of CdS, metallization, and pattern definition.

Barrier effect of AlN film in flexible Cu(In,Ga)Se{sub 2} solar cells on stainless steel foil and solar cell

Energy Technology Data Exchange (ETDEWEB)

Li, Boyan; Li, Jianjun [Institute of Photo-electronic Thin Film Devices and Technology, Key Laboratory of Photo-electronic Thin Film Devices and Technology of Tianjin, Nankai University, Tianjin 300071 (China); Wu, Li [The MOE Key Laboratory of Weak-Light Nonlinear Photonics, School of Physics, Nankai University, Tianjin 300071 (China); Liu, Wei; Sun, Yun [Institute of Photo-electronic Thin Film Devices and Technology, Key Laboratory of Photo-electronic Thin Film Devices and Technology of Tianjin, Nankai University, Tianjin 300071 (China); Zhang, Yi, E-mail: yizhang@nankai.edu.cn [Institute of Photo-electronic Thin Film Devices and Technology, Key Laboratory of Photo-electronic Thin Film Devices and Technology of Tianjin, Nankai University, Tianjin 300071 (China)

2015-04-05

Highlights: • The adhension between AlN film and Mo are verygood. • AlN film can be effectively used as the barrier of flexible CIGS solar cell on SS substrate. • AlN film is suitable as the insulation barrier of flexible CIGS solar cell on SS substrate. - Abstract: The AlN film deposited by DC magnetron sputtering on stainless steel (SS) foils was used as the barrier in flexible Cu(In,Ga)Se{sub 2} (CIGS) solar cells on stainless steel foil and characterized comprehensively by X-ray diffraction (XRD), scanning electron microscopy (SEM), I–V, and QE measurements study. The study of AlN as insulation barrier in the flexible CIGS solar cell showed that the adhesion strength between the SS foil and the deposited AlN film was very strong even after annealing at high temperature at 530 °C. More importantly, a high resistance of over 10 MΩ was remained with the film with thickness of around 200 nm after annealing. This indicates that the AlN film is suitable as an effective insulation barrier in flexible CIGS solar cells based on SS foil. In addition, the XRD and SEM results showed that the AlN film did not influence the crystal structure of the Mo film which was deposited upon the AlN layer and used as the electrical contact in CIGS solar cells. It was found that the AlN film contributed to an improved crystallinity of the Mo contact layer compared to the bare SS foil. The combined results of secondary ion mass spectrometry, I–V and EQE measurements of the corresponding flexible CIGS solar cells confirmed that 1 μm-thick AlN film could be used as an efficient barrier layer in CIGS solar cells on SS foil.

Laser ray tracing and power deposition on an unstructured three-dimensional grid

International Nuclear Information System (INIS)

Kaiser, Thomas B.

2000-01-01

A scheme is presented for laser beam evolution and power deposition on three-dimensional unstructured grids composed of hexahedra, prisms, pyramids, and tetrahedra. The geometrical-optics approximation to the electromagnetic wave equation is used to follow propagation of a collection of discrete rays used to represent the beam(s). Ray trajectory equations are integrated using a method that is second order in time, exact for a constant electron-density gradient, and capable of dealing with density discontinuities that arise in certain hydrodynamics formulations. Power deposition by inverse-bremsstrahlung is modeled with a scheme based on Gaussian quadrature to accommodate a deposition rate whose spatial variation is highly nonuniform. Comparisons with analytic results are given for a density ramp in three dimensions, and a ''quadratic-well'' density trough in two dimensions. (c) 2000 The American Physical Society

Investigation of the effect of potassium on Cu(In,Ga)Se{sub 2} layers and solar cells

Energy Technology Data Exchange (ETDEWEB)

Laemmle, A., E-mail: anke.laemmle@zsw-bw.de; Wuerz, R.; Powalla, M.

2015-05-01

We investigate the influence of potassium (K) on the Cu(In,Ga)Se{sub 2} (CIGS) growth kinetics on alkali-free alumina substrates and the electrical parameters of the CIGS solar cell by intentional K doping of the CIGS layer by a KF-precursor layer and KF-post deposition treatment (PDT). Secondary ion mass spectroscopy measurements revealed that K can be incorporated into the CIGS layer by both processes. The CIGS composition of the KF-precursor sample shows a stronger [Ga]/([Ga] + [In]) (GGI) profile. By analysing the samples with scanning electron microscopy we observed smaller CIGS grains for the KF-precursor sample compared to the K-free reference and KF-PDT sample. jV-measurements of the KF-PDT and the KF-precursor sample show an increase in the cell efficiency η from 10.7% to 13.6% and 13.7%, respectively, compared to the K-free reference sample. The external quantum efficiency measurements of the KF-precursor sample show an increased absorption in the infrared region. Capacitance-voltage measurements reveal an increase in the net doping concentration of both samples treated with K. We assume that the enhancement is caused by passivation of grain boundaries and donor-like defects by K, as previously demonstrated for Na. - Highlights: • K-doped Cu(In,Ga)Se{sub 2} (CIGS) layers from KF-precursor and KF-post deposition treatment • Separation of the K-effect from the Na-effect by using alkali-free substrates • Interdiffusion of CIGS elements during CIGS growth is hindered by K • KF-precursor leads to smaller CIGS grains and a stronger Cu depletion at the CIGS surface. • K leads to an increase in the conversion efficiency.

Influence of sputtering deposition parameters on electrical and optical properties of aluminium-doped zinc oxide thin films for photovoltaic applications

Science.gov (United States)

Krawczak, Ewelina; Agata, Zdyb; Gulkowski, Slawomir; Fave, Alain; Fourmond, Erwann

2017-11-01

Transparent Conductive Oxides (TCOs) characterized by high visible transmittance and low electrical resistivity play an important role in photovoltaic technology. Aluminum doped zinc oxide (AZO) is one of the TCOs that can find its application in thin film solar cells (CIGS or CdTe PV technology) as well as in other microelectronic applications. In this paper some optical and electrical properties of ZnO:Al thin films deposited by RF magnetron sputtering method have been investigated. AZO layers have been deposited on the soda lime glass substrates with use of variable technological parameters such as pressure in the deposition chamber, power applied and temperature during the process. The composition of AZO films has been investigated by EDS method. Thickness and refraction index of the deposited layers in dependence on certain technological parameters of sputtering process have been determined by spectroscopic ellipsometry. The measurements of transmittance and sheet resistance were also performed.

Improving the efficiency of copper indium gallium (Di-selenide (CIGS solar cells through integration of a moth-eye textured resist with a refractive index similar to aluminum doped zinc oxide

Directory of Open Access Journals (Sweden)

M. Burghoorn

2014-12-01

Full Text Available Textured transparent conductors are widely used in thin-film silicon solar cells. They lower the reflectivity at interfaces between different layers in the cell and/or cause an increase in the path length of photons in the Si absorber layer, which both result in an increase in the number of absorbed photons and, consequently, an increase in short-circuit current density (Jsc and cell efficiency. Through optical simulations, we recently obtained strong indications that texturing of the transparent conductor in copper indium gallium (di-selenide (CIGS solar cells is also optically advantageous. Here, we experimentally demonstrate that the Jsc and efficiency of CIGS solar cells with an absorber layer thickness (dCIGS of 0.85 μm, 1.00 μm and 2.00 μm increase through application of a moth-eye textured resist with a refractive index that is sufficiently similar to AZO (nresist = 1.792 vs. nAZO = 1.913 at 633 nm to avoid large optical losses at the resist-AZO interface. On average, Jsc increases by 7.2%, which matches the average reduction in reflection of 7.0%. The average relative increase in efficiency is slightly lower (6.0%. No trend towards a larger relative increase in Jsc with decreasing dCIGS was observed. Ergo, the increase in Jsc can be fully explained by the reduction in reflection, and we did not observe any increase in Jsc based on an increased photon path length.

Local current-voltage behaviors of preferentially and randomly textured Cu(In,Ga)Se2 thin films investigated by conductive atomic force microscopy

International Nuclear Information System (INIS)

Shin, R.H.; Jo, W.; Kim, D.W.; Yun, Jae Ho; Ahn, S.

2011-01-01

Electrical transport properties on polycrystalline Cu(In,Ga)Se 2 (CIGS) (Ga/(In+Ga) ∼35%) thin films were examined by conductive atomic force microscopy. The CIGS thin films with a (112) preferential or random texture were deposited on Mo-coated glass substrates. Triangular pyramidal grain growths were observed in the CIGS thin films preferentially textured to the (112) planes. Current maps of the CIGS surface were acquired with a zero or non-zero external voltage bias. The contrast of the images on the grain boundaries and intragrains displayed the conduction path in the materials. Local current-voltage measurements were performed to evaluate the charge conduction properties of the CIGS thin films. (orig.)

Local current-voltage behaviors of preferentially and randomly textured Cu(In,Ga)Se{sub 2} thin films investigated by conductive atomic force microscopy

Energy Technology Data Exchange (ETDEWEB)

Shin, R.H.; Jo, W. [Ewha Womans University, Department of Physics, Seoul (Korea, Republic of); Kim, D.W. [Ewha Womans University, Department of Physics, Seoul (Korea, Republic of); Ewha Womans University, Department of Chemistry and Nanosciences, Seoul (Korea, Republic of); Yun, Jae Ho; Ahn, S. [Korea Institute of Energy Research, Daejeon (Korea, Republic of)

2011-09-15

Electrical transport properties on polycrystalline Cu(In,Ga)Se{sub 2} (CIGS) (Ga/(In+Ga) {approx}35%) thin films were examined by conductive atomic force microscopy. The CIGS thin films with a (112) preferential or random texture were deposited on Mo-coated glass substrates. Triangular pyramidal grain growths were observed in the CIGS thin films preferentially textured to the (112) planes. Current maps of the CIGS surface were acquired with a zero or non-zero external voltage bias. The contrast of the images on the grain boundaries and intragrains displayed the conduction path in the materials. Local current-voltage measurements were performed to evaluate the charge conduction properties of the CIGS thin films. (orig.)

Stages of ores formation

International Nuclear Information System (INIS)

Khasanov, A.Kh.

1988-01-01

Deposit formation (especially endogenous) is the complicated, multi-stage and long process. Establishment of deposit formation succession, age-specific correlations of minerals and aggregates have a high importance at solving genetic questions. Studying of minerals correlations and mineral aggregates, succession of their crystallization and other observations let restore the history of deposit formation, pick up in it different on duration and physical and chemical conditions stages

Influence of sputtering deposition parameters on electrical and optical properties of aluminium-doped zinc oxide thin films for photovoltaic applications

Directory of Open Access Journals (Sweden)

Krawczak Ewelina

2017-01-01

Full Text Available Transparent Conductive Oxides (TCOs characterized by high visible transmittance and low electrical resistivity play an important role in photovoltaic technology. Aluminum doped zinc oxide (AZO is one of the TCOs that can find its application in thin film solar cells (CIGS or CdTe PV technology as well as in other microelectronic applications. In this paper some optical and electrical properties of ZnO:Al thin films deposited by RF magnetron sputtering method have been investigated. AZO layers have been deposited on the soda lime glass substrates with use of variable technological parameters such as pressure in the deposition chamber, power applied and temperature during the process. The composition of AZO films has been investigated by EDS method. Thickness and refraction index of the deposited layers in dependence on certain technological parameters of sputtering process have been determined by spectroscopic ellipsometry. The measurements of transmittance and sheet resistance were also performed.

Investigation of Non-Vacuum Deposition Techniques in Fabrication of Chalcogenide-Based Solar Cell Absorbers

KAUST Repository

Alsaggaf, Ahmed

2015-07-01

The environmental challenges are increasing, and so is the need for renewable energy. For photovoltaic applications, thin film Cu(In,Ga)(S,Se)2 (CIGS) and CuIn(S,Se)2 (CIS) solar cells are attractive with conversion efficiencies of more than 20%. However, the high-efficiency cells are fabricated using vacuum technologies such as sputtering or thermal co-evaporation, which are very costly and unfeasible at industrial level. The fabrication involves the uses of highly toxic gases such as H2Se, adding complexity to the fabrication process. The work described here focused on non-vacuum deposition methods such as printing. Special attention has been given to printing designed in a moving Roll-to-Roll (R2R) fashion. The results show potential of such technology to replace the vacuum processes. Conversion efficiencies for such non-vacuum deposition of Cu(In,Ga)(S,Se)2 solar cells have exceeded 15% using hazardous chemicals such as hydrazine, which is unsuitable for industrial scale up. In an effort to simplify the process, non-toxic suspensions of Cu(In,Ga)S2 molecular-based precursors achieved efficiencies of ~7-15%. Attempts to further simplify the selenization step, deposition of CuIn(S,Se)2 particulate solutions without the Ga doping and non-toxic suspensions of Cu(In,Ga)Se2 quaternary precursors achieved efficiencies (~1-8%). The contribution of this research was to provide a new method to monitor printed structures through spectral-domain optical coherence tomography SD-OCT in a moving fashion simulating R2R process design at speeds up to 1.05 m/min. The research clarified morphological and compositional impacts of Nd:YAG laser heat-treatment on Cu(In,Ga)Se2 absorber layer to simplify the annealing step in non-vacuum environment compatible to R2R. Finally, the research further simplified development methods for CIGS solar cells based on suspensions of quaternary Cu(In,Ga)Se2 precursors and ternary CuInS2 precursors. The methods consisted of post deposition reactive

Plasma-Assisted Co-evaporation of S and Se for Wide Band Gap Chalcopyrite Photovoltaics: Final Subcontract Report, December 2001 -- April 2005

Energy Technology Data Exchange (ETDEWEB)

Repins, I.; Wolden, C.

2005-08-01

In this work, ITN Energy Systems (ITN) and lower-tier subcontractor Colorado School of Mines (CSM) explore the replacement of the molecular chalcogen precursors during deposition (e.g., Se2 or H2Se) with more reactive chalcogen monomers or radicals (e.g., Se). Molecular species are converted to atomic species in a low-pressure inductively coupled plasma (ICP). This program explored the use of plasma-activated chalcogen sources in CIGS co-evaporation to lower CIGS deposition temperature, increase utilization, increase deposition rate, and improve S:Se stoichiometry control. Plasma activation sources were designed and built, then operated and characterized over a wide range of conditions. Optical emission and mass spectrometry data show that chalcogens are effectively dissociated in the plasma. The enhanced reactivity achieved by the plasma processing was demonstrated by conversion of pre-deposited metal films to respective chalcogen-containing phases at low temperature and low chalcogen flux. The plasma-assisted co-evaporation (PACE) sources were also implemented in CIGS co-evaporation. No benefit from PACE was observed in device results, and frequent deposition failures occurred.

Assessing Reliability of Cold Spray Sputter Targets in Photovoltaic Manufacturing

Science.gov (United States)

Hardikar, Kedar; Vlcek, Johannes; Bheemreddy, Venkata; Juliano, Daniel

2017-10-01

Cold spray has been used to manufacture more than 800 Cu-In-Ga (CIG) sputter targets for deposition of high-efficiency photovoltaic thin films. It is a preferred technique since it enables high deposit purity and transfer of non-equilibrium alloy states to the target material. In this work, an integrated approach to reliability assessment of such targets with deposit weight in excess of 50 lb. is undertaken, involving thermal-mechanical characterization of the material in as-deposited condition, characterization of the interface adhesion on cylindrical substrate in as-deposited condition, and developing means to assess target integrity under thermal-mechanical loads during the physical vapor deposition (PVD) sputtering process. Mechanical characterization of cold spray deposited CIG alloy is accomplished through the use of indentation testing and adaptation of Brazilian disk test. A custom lever test was developed to characterize adhesion along the cylindrical interface between the CIG deposit and cylindrical substrate, overcoming limitations of current standards. A cohesive zone model for crack initiation and propagation at the deposit interface is developed and validated using the lever test and later used to simulate the potential catastrophic target failure in the PVD process. It is shown that this approach enables reliability assessment of sputter targets and improves robustness.

Improving the efficiency of copper indium gallium (Di-)selenide (CIGS) solar cells through integration of a moth-eye textured resist with a refractive index similar to aluminum doped zinc oxide

Energy Technology Data Exchange (ETDEWEB)

Burghoorn, M.; Kniknie, B.; Deelen, J. van; Ee, R. van [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); Xu, M. [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); Delft University of Technology, Optics Group, Van der Waalsweg 8, 2628 CH, Delft (Netherlands); Vroon, Z. [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); Zuyd Hogeschool, Nieuw Eyckholt 300, 6419 DJ, Heerlen (Netherlands); Belt, R. van de [Kriya Materials BV, Urmonderbaan 22, 6167 RD, Geleen (Netherlands); Buskens, P., E-mail: pascal.buskens@tno.nl, E-mail: buskens@dwi.rwth-aachen.de [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); DWI – Leibniz Institute for Interactive Materials, Forckenbeckstrasse 50, 52056, Aachen (Germany)

2014-12-15

Textured transparent conductors are widely used in thin-film silicon solar cells. They lower the reflectivity at interfaces between different layers in the cell and/or cause an increase in the path length of photons in the Si absorber layer, which both result in an increase in the number of absorbed photons and, consequently, an increase in short-circuit current density (J{sub sc}) and cell efficiency. Through optical simulations, we recently obtained strong indications that texturing of the transparent conductor in copper indium gallium (di-)selenide (CIGS) solar cells is also optically advantageous. Here, we experimentally demonstrate that the J{sub sc} and efficiency of CIGS solar cells with an absorber layer thickness (d{sub CIGS}) of 0.85 μm, 1.00 μm and 2.00 μm increase through application of a moth-eye textured resist with a refractive index that is sufficiently similar to AZO (n{sub resist} = 1.792 vs. n{sub AZO} = 1.913 at 633 nm) to avoid large optical losses at the resist-AZO interface. On average, J{sub sc} increases by 7.2%, which matches the average reduction in reflection of 7.0%. The average relative increase in efficiency is slightly lower (6.0%). No trend towards a larger relative increase in J{sub sc} with decreasing d{sub CIGS} was observed. Ergo, the increase in J{sub sc} can be fully explained by the reduction in reflection, and we did not observe any increase in J{sub sc} based on an increased photon path length.

An Enhanced Preventive Maintenance Optimization Model Based on a Three-Stage Failure Process

Directory of Open Access Journals (Sweden)

Ruifeng Yang

2015-01-01

Full Text Available Nuclear power plants are highly complex systems and the issues related to their safety are of primary importance. Probabilistic safety assessment is regarded as the most widespread methodology for studying the safety of nuclear power plants. As maintenance is one of the most important factors for affecting the reliability and safety, an enhanced preventive maintenance optimization model based on a three-stage failure process is proposed. Preventive maintenance is still a dominant maintenance policy due to its easy implementation. In order to correspond to the three-color scheme commonly used in practice, the lifetime of system before failure is divided into three stages, namely, normal, minor defective, and severe defective stages. When the minor defective stage is identified, two measures are considered for comparison: one is that halving the inspection interval only when the minor defective stage is identified at the first time; the other one is that if only identifying the minor defective stage, the subsequent inspection interval is halved. Maintenance is implemented immediately once the severe defective stage is identified. Minimizing the expected cost per unit time is our objective function to optimize the inspection interval. Finally, a numerical example is presented to illustrate the effectiveness of the proposed models.

Three-stage linear, split-Stirling cryocooler for 1 to 2K magnetic cold stage

International Nuclear Information System (INIS)

Longsworth, R.C.

1993-08-01

A long-life, linear, high efficiency 8K split Stirling cycle cryocooler was designed, built, and tested. The refrigerator is designed for cooling a 50 mW, 1.5K magnetic cold stage. Dual opposed piston compressors are driven by moving-coil linear motors. The three stage expander, although not completed, is also driven by a linear motor and is designed to produce 1 SW at 60K, 4W at 16K, and 1.2W at 8K. The cold regenerator employs a parallel gap construction for high efficiency. The key technology areas addressed include warm and cold flexible suspension bearings and a new cold regenerator geometry for high efficiency at 8K

A two-phase inspection model for a single component system with three-stage degradation

International Nuclear Information System (INIS)

Wang, Huiying; Wang, Wenbin; Peng, Rui

2017-01-01

This paper presents a two-phase inspection schedule and an age-based replacement policy for a single plant item contingent on a three-stage degradation process. The two phase inspection schedule can be observed in practice. The three stages are defined as the normal working stage, low-grade defective stage and critical defective stage. When an inspection detects that an item is in the low-grade defective stage, we may delay the preventive replacement action if the time to the age-based replacement is less than or equal to a threshold level. However, if it is above this threshold level, the item will be replaced immediately. If the item is found in the critical defective stage, it is replaced immediately. A hybrid bee colony algorithm is developed to find the optimal solution for the proposed model which has multiple decision variables. A numerical example is conducted to show the efficiency of this algorithm, and simulations are conducted to verify the correctness of the model. - Highlights: • A two-phase inspection model is studied. • The failure process has three stages. • The delayed replacement is considered.

Layer-by-Layer Nanoassembly of Copper Indium Gallium Selenium Nanoparticle Films for Solar Cell Applications

Directory of Open Access Journals (Sweden)

A. Hemati

2012-01-01

Full Text Available Thin films of CIGS nanoparticles interdigited with polymers have been fabricated through a cost-effective nonvacuum film deposition process called layer-by-layer (LbL nanoassembly. CIGS nanoparticles synthesized by heating copper chloride, indium chloride, gallium chloride, and selenium in oleylamine were dispersed in water, and desired surface charges were obtained through pH regulation and by coating the particles with polystyrene sulfonate (PSS. Raising the pH of the nanoparticle dispersion reduced the zeta-potential from +61 mV at pH 7 to −51 mV at pH 10.5. Coating the CIGS nanoparticles with PSS (CIGS-PSS produced a stable dispersion in water with −56.9 mV zeta-potential. Thin films of oppositely charged CIGS nanoparticles (CIGS/CIGS, CIGS nanoparticles and PSS (CIGS/PSS, and PSS-coated CIGS nanoparticles and polyethylenimine (CIGS-PSS/PEI were constructed through the LbL nanoassembly. Film thickness and resistivity of each bilayer of the films were measured, and photoelectric properties of the films were studied for solar cell applications. Solar cell devices fabricated with a 219 nm CIGS film, when illuminated by 50 W light-source, produced 0.7 V open circuit voltage and 0.3 mA/cm2 short circuit current density.

Raster Scan Computer Image Generation (CIG) System Based On Refresh Memory

Science.gov (United States)

Dichter, W.; Doris, K.; Conkling, C.

1982-06-01

A full color, Computer Image Generation (CIG) raster visual system has been developed which provides a high level of training sophistication by utilizing advanced semiconductor technology and innovative hardware and firmware techniques. Double buffered refresh memory and efficient algorithms eliminate the problem of conventional raster line ordering by allowing the generated image to be stored in a random fashion. Modular design techniques and simplified architecture provide significant advantages in reduced system cost, standardization of parts, and high reliability. The major system components are a general purpose computer to perform interfacing and data base functions; a geometric processor to define the instantaneous scene image; a display generator to convert the image to a video signal; an illumination control unit which provides final image processing; and a CRT monitor for display of the completed image. Additional optional enhancements include texture generators, increased edge and occultation capability, curved surface shading, and data base extensions.

Antimony assisted low-temperature processing of CuIn{sub 1-x}Ga{sub x}Se{sub 2-y}S{sub y} solar cells

Energy Technology Data Exchange (ETDEWEB)

Min, Yuan [IBM T. J. Watson Research Center, P. O. Box 218, Yorktown Heights, NY 10598 (United States); Mitzi, David B., E-mail: dmitzi@us.ibm.co [IBM T. J. Watson Research Center, P. O. Box 218, Yorktown Heights, NY 10598 (United States); Gunawan, Oki [IBM T. J. Watson Research Center, P. O. Box 218, Yorktown Heights, NY 10598 (United States); Kellock, Andrew J [IBM Almaden Research Center, 650 Harry Rd, San Jose, CA 95120 (United States); Chey, S Jay [IBM T. J. Watson Research Center, P. O. Box 218, Yorktown Heights, NY 10598 (United States); Deline, Vaughn R [IBM Almaden Research Center, 650 Harry Rd, San Jose, CA 95120 (United States)

2010-11-01

Application of the Sb-doping method to low-temperature ({<=} 400 {sup o}C) processing of CuIn{sub 1-x}Ga{sub x}Se{sub 2-y}S{sub y} (CIGS) solar cells is explored, using a hydrazine-based approach to deposit the absorber films. Power conversion efficiencies of 10.5% and 8.4% have been achieved for CIGS devices (0.45 cm{sup 2} device area) processed at 400 {sup o}C and 360 {sup o}C, respectively, with an Sb-incorporation level at 1.2 mol % (relative to the moles of CIGS). Significant Sb-induced grain size enhancement was confirmed for these low processing temperatures using cross-sectional scanning electron microscopy, and an average 2-3% absolute efficiency improvement was achieved in Sb-doped samples compared to their Sb-free sister samples. With Sb inclusion, the CIGS film grain growth temperature is lowered to well below 450 {sup o}C, a range compatible with flexible polymer substrate materials such as polyimide. This method opens up access to opportunities in low-temperature processing of CIGS solar cells, an area that is being actively pursued using both traditional vacuum-based as well as other solution-based deposition techniques.

Antimony assisted low-temperature processing of CuIn1-xGaxSe2-ySy solar cells

International Nuclear Information System (INIS)

Yuan Min; Mitzi, David B.; Gunawan, Oki; Kellock, Andrew J.; Chey, S. Jay; Deline, Vaughn R.

2010-01-01

Application of the Sb-doping method to low-temperature (≤ 400 o C) processing of CuIn 1-x Ga x Se 2-y S y (CIGS) solar cells is explored, using a hydrazine-based approach to deposit the absorber films. Power conversion efficiencies of 10.5% and 8.4% have been achieved for CIGS devices (0.45 cm 2 device area) processed at 400 o C and 360 o C, respectively, with an Sb-incorporation level at 1.2 mol % (relative to the moles of CIGS). Significant Sb-induced grain size enhancement was confirmed for these low processing temperatures using cross-sectional scanning electron microscopy, and an average 2-3% absolute efficiency improvement was achieved in Sb-doped samples compared to their Sb-free sister samples. With Sb inclusion, the CIGS film grain growth temperature is lowered to well below 450 o C, a range compatible with flexible polymer substrate materials such as polyimide. This method opens up access to opportunities in low-temperature processing of CIGS solar cells, an area that is being actively pursued using both traditional vacuum-based as well as other solution-based deposition techniques.

Tracking the multi-stage exhumation history of the western Chinese Tianshan by Apatite Fission Track (AFT) dating - Implications for the preservation of epithermal deposits in ancient orogenic belt

Science.gov (United States)

Wang, Yannan; Cai, Keda

2017-04-01

The western Chinese Tianshan, located in the southern domain of the Central Asian Orogenic Belt (CAOB), was originally constructed by multiple accretion-collision processes in the Paleozoic, and was superimposed by complex intracontinental tectonic evolution in the Mesozoic-Cenozoic. Understanding the timing and mechanism of the latter geological processes is critical to unravel the preservation conditions of the epithermal deposits in the western Chinese Tianshan. This work presents new apatite fission track (AFT) data for three mountain ranges of the western Chinese Tianshan to track their exhumation history. Our AFT data gave a wide range of ages from 76.8 ± 5.5 Ma to 182.3 ± 9.9 Ma, and the mean confined fission track lengths are between 9.8 ± 0.5 μm and 12.3 ± 0.2 μm. The new data, in combination with the thermal history modeling，enable us to attribute the exhumation history to three primary stages, including Early Permian (300-280 Ma), Late Triassic-Early Cretaceous (230-130 Ma), and Late Oligocene-Early Miocene (30-20 Ma). The first stage may be caused by the terrane accretion-collision in the late Paleozoic. The second stage was likely related to the closure of the Mongol-Okhotsk Ocean during the Mesozoic. The last one is regarded as the result of the collision between the Indian Plate and the Eurasia Plate in the Cenozoic. The extraordinary exhumation processes of these three major mountain ranges might have been responsible for sediment supply to the corresponding intra-mountain basins in the western Chinese Tianshan, and the particularly mountain-basin coupling evolution is ascribed to an essential condition for the preservation of epithermal deposits in ancient orogenic belt.

CIGS Solar Cells for Space Applications: Numerical Simulation of the Effect of Traps Created by High-Energy Electron and Proton Irradiation on the Performance of Solar Cells

Science.gov (United States)

Dabbabi, Samar; Ben Nasr, Tarek; Turki Kamoun, Najoua

2018-02-01

Numerical simulation is carried out using the Silvaco ATLAS software to predict the effect of 1-MeV electron and 4-MeV proton irradiation on the performance of a Cu(In, Ga)Se2 (CIGS) solar cell that operates under the air mass zero spectrum (AM0). As a consequence of irradiation, two types of traps are induced including the donor- and acceptor-type traps. Only one of them (the donor-type trap) is found responsible for the degradation of the open-circuit voltage (V OC), fill factor (FF) and efficiency (η), while the short circuit current (J SC) remains essentially unaffected. The modelling simulation validity is verified by comparison with the experimental data. This article shows that CIGS solar cells are suited for space applications.

Investigating the electronic properties of Al2O3/Cu(In,GaSe2 interface

Directory of Open Access Journals (Sweden)

R. Kotipalli

2015-10-01

Full Text Available Atomic layer deposited (ALD Al2O3 films on Cu(In,GaSe2 (CIGS surfaces have been demonstrated to exhibit excellent surface passivation properties, which is advantageous in reducing recombination losses at the rear metal contact of CIGS thin-film solar cells. Here, we report, for the first time, experimentally extracted electronic parameters, i.e. fixed charge density (Qf and interface-trap charge density (Dit, for as-deposited (AD and post-deposition annealed (PDA ALD Al2O3 films on CIGS surfaces using capacitance–voltage (C-V and conductance-frequency (G-f measurements. These results indicate that the AD films exhibit positive fixed charges Qf (approximately 1012 cm−2, whereas the PDA films exhibit a very high density of negative fixed charges Qf (approximately 1013 cm−2. The extracted Dit values, which reflect the extent of chemical passivation, were found to be in a similar range of order (approximately 1012 cm−2 eV−1 for both AD and PDA samples. The high density of negative Qf in the bulk of the PDA Al2O3 film exerts a strong Coulomb repulsive force on the underlying CIGS minority carriers (ns, preventing them to recombine at the CIGS/Al2O3 interface. Using experimentally extracted Qf and Dit values, SCAPS simulation results showed that the surface concentration of minority carriers (ns in the PDA films was approximately eight-orders of magnitude lower than in the AD films. The electrical characterization and estimations presented in this letter construct a comprehensive picture of the interfacial physics involved at the Al2O3/CIGS interface.

Phosphorus utilization by three rice varieties at different stages of growth in a vertisol

International Nuclear Information System (INIS)

Rastogi, A.K.; Mahajan, J.P.; Sinha, S.B.

1981-01-01

A pot experiment was conducted using labelled superphosphate to study the utilization of applied fertilizer phosphorus by three rice varieties, viz., Jaya, Ratna and Sona at tillering, flowering and harvesting stages. Total phosphorus uptake and phosphorus derived from fertilizer increased significantly with increasing level of phosphorus, but per cent utilization of applied phosphorus showed a reverse trend in all the three varieties at all the growth stages. Dry matter yield in general, increased significantly with increasing P levels in all the three varieties. Average soil-p uptake decreased with increasing levels of phosphorus at all the stages. (author)

Achieving uniform layer deposition by atmospheric-pressure plasma-enhanced chemical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

Lee, Jae-Ok [Department of Plasma Engineering, Korea Institute of Machinery & Materials (KIMM), Daejeon 305-343 (Korea, Republic of); Kang, Woo Seok, E-mail: kang@kimm.re.kr [Department of Plasma Engineering, Korea Institute of Machinery & Materials (KIMM), Daejeon 305-343 (Korea, Republic of); Department of Environment & Energy Mechanical Engineering, University of Science & Technology (UST), Daejeon 305-350 (Korea, Republic of); Hur, Min; Lee, Jin Young [Department of Plasma Engineering, Korea Institute of Machinery & Materials (KIMM), Daejeon 305-343 (Korea, Republic of); Song, Young-Hoon [Department of Plasma Engineering, Korea Institute of Machinery & Materials (KIMM), Daejeon 305-343 (Korea, Republic of); Department of Environment & Energy Mechanical Engineering, University of Science & Technology (UST), Daejeon 305-350 (Korea, Republic of)

2015-12-31

This work investigates the use of plasma-enhanced chemical vapor deposition under atmospheric pressure for achieving uniform layer formation. Electrical and optical measurements demonstrated that the counterbalance between oxygen and precursors maintained the homogeneous discharge mode, while creating intermediate species for layer deposition. Several steps of the deposition process of the layers, which were processed on a stationary stage, were affected by flow stream and precursor depletion. This study showed that by changing the flow streamlines using substrate stage motion uniform layer deposition under atmospheric pressure can be achieved. - Highlights: • Zirconium oxide was deposited by atmospheric-pressure plasma-enhanced chemical vapor deposition. • Homogeneous plasma was maintained by counterbalancing between discharge gas and precursors. • Several deposition steps were observed affected by the gas flow stream and precursor depletion. • Thin film layer was uniformly grown when the substrate underwent a sweeping motion.

Metallogenetic condition and mineralization characteristics of uranium deposit No.114

International Nuclear Information System (INIS)

Niu Lin; Ma Fei; Yang Wanjin

1988-01-01

Deposit No 114 is one of the typical carbonate-type uranium deposits, that are widely distributed in South China. In this paper formational environment of host rock, wall-rock alteration, sulfur, oxygen, carbon isotopes, mineralization temperatures, ore compsitions were studied. Based on the U-Pb isotopic research three mineralization stages in deposit No 114 were established, namely 104 Ma, 61 Ma and 11 Ma. It is suggested, that the deposit No 114 is a polygenetic deposit formed primarily by supergene leaching and hydrothermal reworked. The uranium deposit has multi-sources, the main uranium source of which is from the granite body situated nearby. According to metallogenetic characteristics the authors suggest the favourable geological exploration guides for this kind of ore deposits

Psychiatry in primary care using the three-stage assessment

African Journals Online (AJOL)

terms of the patient's readiness to change his/her behaviour and then use an agenda-setting technique to decide which risk factor to .... and occasionally uses cannabis. She is not using any family planning (besides ... require a long-term relationship with their primary care physician,. Table 1. The three-stage assessment.

Determining skeletal maturation stage using cervical vertebrae: evaluation of three diagnostic methods

Directory of Open Access Journals (Sweden)

Luci Mara Fachardo Jaqueira

2010-12-01

Full Text Available The aim of the present study was to compare the use of three cervical vertebral evaluation methods (Hassel-Farman, Baccetti et al., and Seedat-Forsberg for determinating skeletal maturation stage in orthodontic patients. Twenty-three radiographs were randomly selected from a private orthodontic practice. Each radiograph was analyzed on three separate occasions by four evaluators (one radiologist and three orthodontists, who determined the skeletal maturation stage using the references established by each of the three methods. Intraevaluator and interevaluator comparisons were performed, and the degree of agreement was established using the weighted Kappa coefficient (95% CI. Good agreement (Kappa between 0.61 and 0.80 was observed between the determinations of most of the evaluators. The three methods demonstrated clinical applicability. However, the method proposed by Baccetti et al. achieved the best results, followed by the Hassel-Farman and the Seedat-Forsberg methods.

Investigation of an Electrochemical Method for Separation of Copper, Indium, and Gallium from Pretreated CIGS Solar Cell Waste Materials

Directory of Open Access Journals (Sweden)

Anna M. K. Gustafsson

2015-01-01

Full Text Available Recycling of the semiconductor material copper indium gallium diselenide (CIGS is important to ensure a future supply of indium and gallium, which are relatively rare and therefore expensive elements. As a continuation of our previous work, where we recycled high purity selenium from CIGS waste materials, we now show that copper and indium can be recycled by electrodeposition from hydrochloric acid solutions of dissolved selenium-depleted material. Suitable potentials for the reduction of copper and indium were determined to be −0.5 V and −0.9 V (versus the Ag/AgCl reference electrode, respectively, using cyclic voltammetry. Electrodeposition of first copper and then indium from a solution containing the dissolved residue from the selenium separation and ammonium chloride in 1 M HCl gave a copper yield of 100.1 ± 0.5% and an indium yield of 98.1 ± 2.5%. The separated copper and indium fractions contained no significant contamination of the other elements. Gallium remained in solution together with a small amount of indium after the separation of copper and indium and has to be recovered by an alternative method since electrowinning from the chloride-rich acid solution was not effective.

Facile Growth of Cu2ZnSnS4 Thin-Film by One-Step Pulsed Hybrid Electrophoretic and Electroplating Deposition

Science.gov (United States)

Tsai, Hung-Wei; Chen, Chia-Wei; Thomas, Stuart R.; Hsu, Cheng-Hung; Tsai, Wen-Chi; Chen, Yu-Ze; Wang, Yi-Chung; Wang, Zhiming M.; Hong, Hwen-Fen; Chueh, Yu-Lun

2016-01-01

The use of costly and rare metals such as indium and gallium in Cu(In,Ga)Se2 (CIGS) based solar cells has motivated research into the use of Cu2ZnSnS4 (CZTS) as a suitable replacement due to its non-toxicity, abundance of compositional elements and excellent optical properties (1.5 eV direct band gap and absorption coefficient of ~104 cm−1). In this study, we demonstrate a one-step pulsed hybrid electrodeposition method (PHED), which combines electrophoretic and electroplating deposition to deposit uniform CZTS thin-films. Through careful analysis and optimization, we are able to demonstrate CZTS solar cells with the VOC, JSC, FF and η of 350 mV, 3.90 mA/cm2, 0.43 and 0.59%, respectively. PMID:26902556

OPHTHALMIC FINDINGS IN LATE STAGE SJOGREN-LARSSON SYNDROME.

Science.gov (United States)

Nanda, Tavish; Kovach, Jaclyn L

2017-03-15

To report spectral domain optical coherence tomography and fundus autofluorescence documentation of late stage macular findings associated with Sjogren-Larsson Syndrome in three adult siblings. Three adult siblings with Sjogren-Larsson Syndrome underwent ophthalmic examination and imaging. Crystalline maculopathy and subretinal deposits, presumably lipofuscin accumulation, with macular atrophy were present in varying degrees in all three adult siblings. In adults with Sjogren-Larsson Syndrome, crystalline retinopathy can progress to macular atrophy and the appearance of lipofuscin accumulation.

Employing Si solar cell technology to increase efficiency of ultra-thin Cu(In,Ga)Se2 solar cells.

Science.gov (United States)

Vermang, Bart; Wätjen, Jörn Timo; Fjällström, Viktor; Rostvall, Fredrik; Edoff, Marika; Kotipalli, Ratan; Henry, Frederic; Flandre, Denis

2014-10-01

Reducing absorber layer thickness below 500 nm in regular Cu(In,Ga)Se 2 (CIGS) solar cells decreases cell efficiency considerably, as both short-circuit current and open-circuit voltage are reduced because of incomplete absorption and high Mo/CIGS rear interface recombination. In this work, an innovative rear cell design is developed to avoid both effects: a highly reflective rear surface passivation layer with nano-sized local point contact openings is employed to enhance rear internal reflection and decrease the rear surface recombination velocity significantly, as compared with a standard Mo/CIGS rear interface. The formation of nano-sphere shaped precipitates in chemical bath deposition of CdS is used to generate nano-sized point contact openings. Evaporation of MgF 2 coated with a thin atomic layer deposited Al 2 O 3 layer, or direct current magnetron sputtering of Al 2 O 3 are used as rear surface passivation layers. Rear internal reflection is enhanced substantially by the increased thickness of the passivation layer, and also the rear surface recombination velocity is reduced at the Al 2 O 3 /CIGS rear interface. (MgF 2 /)Al 2 O 3 rear surface passivated ultra-thin CIGS solar cells are fabricated, showing an increase in short circuit current and open circuit voltage compared to unpassivated reference cells with equivalent CIGS thickness. Accordingly, average solar cell efficiencies of 13.5% are realized for 385 nm thick CIGS absorber layers, compared with 9.1% efficiency for the corresponding unpassivated reference cells.

Employing Si solar cell technology to increase efficiency of ultra-thin Cu(In,Ga)Se2 solar cells

Science.gov (United States)

Vermang, Bart; Wätjen, Jörn Timo; Fjällström, Viktor; Rostvall, Fredrik; Edoff, Marika; Kotipalli, Ratan; Henry, Frederic; Flandre, Denis

2014-01-01

Reducing absorber layer thickness below 500 nm in regular Cu(In,Ga)Se2 (CIGS) solar cells decreases cell efficiency considerably, as both short-circuit current and open-circuit voltage are reduced because of incomplete absorption and high Mo/CIGS rear interface recombination. In this work, an innovative rear cell design is developed to avoid both effects: a highly reflective rear surface passivation layer with nano-sized local point contact openings is employed to enhance rear internal reflection and decrease the rear surface recombination velocity significantly, as compared with a standard Mo/CIGS rear interface. The formation of nano-sphere shaped precipitates in chemical bath deposition of CdS is used to generate nano-sized point contact openings. Evaporation of MgF2 coated with a thin atomic layer deposited Al2O3 layer, or direct current magnetron sputtering of Al2O3 are used as rear surface passivation layers. Rear internal reflection is enhanced substantially by the increased thickness of the passivation layer, and also the rear surface recombination velocity is reduced at the Al2O3/CIGS rear interface. (MgF2/)Al2O3 rear surface passivated ultra-thin CIGS solar cells are fabricated, showing an increase in short circuit current and open circuit voltage compared to unpassivated reference cells with equivalent CIGS thickness. Accordingly, average solar cell efficiencies of 13.5% are realized for 385 nm thick CIGS absorber layers, compared with 9.1% efficiency for the corresponding unpassivated reference cells. PMID:26300619

A Three-Stage Birandom Program for Unit Commitment with Wind Power Uncertainty

Directory of Open Access Journals (Sweden)

Na Zhang

2014-01-01

Full Text Available The integration of large-scale wind power adds a significant uncertainty to power system planning and operating. The wind forecast error is decreased with the forecast horizon, particularly when it is from one day to several hours ahead. Integrating intraday unit commitment (UC adjustment process based on updated ultra-short term wind forecast information is one way to improve the dispatching results. A novel three-stage UC decision method, in which the day-ahead UC decisions are determined in the first stage, the intraday UC adjustment decisions of subfast start units are determined in the second stage, and the UC decisions of fast-start units and dispatching decisions are determined in the third stage is presented. Accordingly, a three-stage birandom UC model is presented, in which the intraday hours-ahead forecasted wind power is formulated as a birandom variable, and the intraday UC adjustment event is formulated as a birandom event. The equilibrium chance constraint is employed to ensure the reliability requirement. A birandom simulation based hybrid genetic algorithm is designed to solve the proposed model. Some computational results indicate that the proposed model provides UC decisions with lower expected total costs.

Differential metabolic responses in three life stages of mussels Mytilus galloprovincialis exposed to cadmium.

Science.gov (United States)

Wu, Huifeng; Xu, Lanlan; Yu, Deliang; Ji, Chenglong

2017-01-01

Cadmium (Cd) is one of the most important metal contaminants in the Bohai Sea. In this work, NMR-based metabolomics was used to investigate the toxicological effects of Cd at an environmentally relevant concentration (50 µg L -1 ) in three different life stages (D-shape larval, juvenile and adult) of mussels Mytilus galloprovincialis. Results indicated that the D-shape larval mussel was the most sensitive life stage to Cd. The significantly different metabolic profiles meant that Cd induced differential toxicological effects in three life stages of mussels. Basically, Cd caused osmotic stress in all the three life stages via different metabolic pathways. Cd exposure reduced the anaerobiosis in D-shape larval mussels and disturbed lipid metabolism in juvenile mussels, respectively. Compared with the D-shape larval and juvenile mussels, the adult mussels reduced energy consumption to deal with Cd stress.

An Investigation on the Formation of Carbon Nanotubes by Two-Stage Chemical Vapor Deposition

Directory of Open Access Journals (Sweden)

M. S. Shamsudin

2012-01-01

Full Text Available High density of carbon nanotubes (CNTs has been synthesized from agricultural hydrocarbon: camphor oil using a one-hour synthesis time and a titanium dioxide sol gel catalyst. The pyrolysis temperature is studied in the range of 700–900°C at increments of 50°C. The synthesis process is done using a custom-made two-stage catalytic chemical vapor deposition apparatus. The CNT characteristics are investigated by field emission scanning electron microscopy and micro-Raman spectroscopy. The experimental results showed that structural properties of CNT are highly dependent on pyrolysis temperature changes.

Highly reflective rear surface passivation design for ultra-thin Cu(In,Ga)Se{sub 2} solar cells

Energy Technology Data Exchange (ETDEWEB)

Vermang, Bart, E-mail: Bart.Vermang@angstrom.uu.se [Ångström Solar Center, University of Uppsala, Uppsala 75121 (Sweden); ESAT-KU Leuven, University of Leuven, Leuven 3001 (Belgium); Wätjen, Jörn Timo; Fjällström, Viktor; Rostvall, Fredrik; Edoff, Marika [Ångström Solar Center, University of Uppsala, Uppsala 75121 (Sweden); Gunnarsson, Rickard; Pilch, Iris; Helmersson, Ulf [Plasma & Coatings Physics, University of Linköping, Linköping 58183 (Sweden); Kotipalli, Ratan; Henry, Frederic; Flandre, Denis [ICTEAM/IMNC, Université Catholique de Louvain, Louvain-la-Neuve 1348 (Belgium)

2015-05-01

Al{sub 2}O{sub 3} rear surface passivated ultra-thin Cu(In,Ga)Se{sub 2} (CIGS) solar cells with Mo nano-particles (NPs) as local rear contacts are developed to demonstrate their potential to improve optical confinement in ultra-thin CIGS solar cells. The CIGS absorber layer is 380 nm thick and the Mo NPs are deposited uniformly by an up-scalable technique and have typical diameters of 150 to 200 nm. The Al{sub 2}O{sub 3} layer passivates the CIGS rear surface between the Mo NPs, while the rear CIGS interface in contact with the Mo NP is passivated by [Ga]/([Ga] + [In]) (GGI) grading. It is shown that photon scattering due to the Mo NP contributes to an absolute increase in short circuit current density of 3.4 mA/cm{sup 2}; as compared to equivalent CIGS solar cells with a standard back contact. - Highlights: • Proof-of-principle ultra-thin CIGS solar cells have been fabricated. • The cells have Mo nano-particles (NPs) as local rear contacts. • An Al{sub 2}O{sub 3} film passivates the CIGS rear surface between these nano-particles. • [Ga]/([Ga] + [In]) grading is used to reduce Mo-NP/CIGS interface recombination.

Metallogenesis and metallogenic model of Nuheting uranium deposit in Erlian Basin

International Nuclear Information System (INIS)

Li Hongjun; Kuang Wenzhan

2010-01-01

Based on the study on geological characteristics, metallogesis and geochemical features in Nuheting uranium deposit, it is considered that the deposit belongs to syn-sedimentary and epigenetic reworking type. The deposit position was controlled by the lake area developed during Erlian period in Late Cretaceous. The metallognesis has experienced three stages, they are syn-sedimentary metallogenesis, epigenetic reworking metallogenesis and exogenic metallogenesis. The ore-forming ages are respectively 85 Ma, (41±5)Ma and 6-13 Ma. Based on the summary of metallogenic geological features,metallogenesis and geochemical features, the metallogenic model of Nuheting uranium deposit has been established. (authors)

Thin Film CIGS Solar Cells, Photovoltaic Modules, and the Problems of Modeling

Directory of Open Access Journals (Sweden)

Antonino Parisi

2013-01-01

Full Text Available Starting from the results regarding a nonvacuum technique to fabricate CIGS thin films for solar cells by means of single-step electrodeposition, we focus on the methodological problems of modeling at cell structure and photovoltaic module levels. As a matter of fact, electrodeposition is known as a practical alternative to costly vacuum-based technologies for semiconductor processing in the photovoltaic device sector, but it can lead to quite different structural and electrical properties. For this reason, a greater effort is required to ensure that the perspectives of the electrical engineer and the material scientist are given an opportunity for a closer comparison and a common language. Derived parameters from ongoing experiments have been used for simulation with the different approaches, in order to develop a set of tools which can be used to put together modeling both at single cell structure and complete module levels.

Determinants Factors of Interest Rates on Three-Month Deposits of Bank Persero

Directory of Open Access Journals (Sweden)

Tedy Kurniawan

2017-03-01

Full Text Available This research aims at analyzing the influence of Capital Adequacy Ratio (CAR, Operating Expenses of Operating Income (BOPO, inflation, exchange rate, and the amount of money supply (M1 to the interest rate of three month deposits of the State-Owned Bank in Indonesia in 2007-2015. This research uses the error correction model analysis. The result obtained is the CAR that has a significant effect on the long term and has no effect on the short term, BOPO has a significant influence on the long term and short term, inflation has the significant effect on the long term and has no effect on the short term, the exchange rate has an influence on the short and long term, the money supply has no effects on the short and long-term on the interest rate on three month deposits of the State-Owned Bank.

Effect of zinc addition on properties of cadmium sulfide layer and performance of Cu(In,Ga)Se{sub 2} solar cell

Energy Technology Data Exchange (ETDEWEB)

Bae, Dowon, E-mail: bae.dowon@yahoo.co.kr; Gho, Junghwan; Shin, Minjung; Kwon, Sehan

2013-05-01

Cd{sub (1−x)}Zn{sub x}S (CdS:Zn) thin films were grown on an indium tin oxide-coated glass substrate and Cu(In,Ga)Se{sub 2} (CIGS) surface by chemical bath deposition for solar cell applications, and their composition, and optical properties were studied to decide the optimum process conditions for buffer layer growth. The average conversion efficiency of CIGS solar panels (24-in.) with the CdS:Zn layer was 0.35% higher than that of conventional solar panels mainly because of the increased open-circuit voltage. This efficiency improvement was not due to modification of the optical properties of the buffer layer, but due to the change in the deposition rate during buffer layer growth. - Highlights: ► CdS:Zn buffer layers were fabricated for Cu(In,Ga)Se{sub 2} (CIGS) photovoltaic (PV) panels. ► Composition of buffer layers on indium–tin–oxide (ITO) and CIGS was investigated. ► Transmittance of CdS:Zn on ITO coated glass showed 5% higher than CdS. ► Efficiency of CdS:Zn solution adopted panels showed 0.47% higher than that with CdS. ► However, it was revealed that only Cd and S ions were found at the surface of CIGS.

Potassium-induced surface modification of Cu(In,Ga)Se2 thin films for high-efficiency solar cells.

Science.gov (United States)

Chirilă, Adrian; Reinhard, Patrick; Pianezzi, Fabian; Bloesch, Patrick; Uhl, Alexander R; Fella, Carolin; Kranz, Lukas; Keller, Debora; Gretener, Christina; Hagendorfer, Harald; Jaeger, Dominik; Erni, Rolf; Nishiwaki, Shiro; Buecheler, Stephan; Tiwari, Ayodhya N

2013-12-01

Thin-film photovoltaic devices based on chalcopyrite Cu(In,Ga)Se2 (CIGS) absorber layers show excellent light-to-power conversion efficiencies exceeding 20%. This high performance level requires a small amount of alkaline metals incorporated into the CIGS layer, naturally provided by soda lime glass substrates used for processing of champion devices. The use of flexible substrates requires distinct incorporation of the alkaline metals, and so far mainly Na was believed to be the most favourable element, whereas other alkaline metals have resulted in significantly inferior device performance. Here we present a new sequential post-deposition treatment of the CIGS layer with sodium and potassium fluoride that enables fabrication of flexible photovoltaic devices with a remarkable conversion efficiency due to modified interface properties and mitigation of optical losses in the CdS buffer layer. The described treatment leads to a significant depletion of Cu and Ga concentrations in the CIGS near-surface region and enables a significant thickness reduction of the CdS buffer layer without the commonly observed losses in photovoltaic parameters. Ion exchange processes, well known in other research areas, are proposed as underlying mechanisms responsible for the changes in chemical composition of the deposited CIGS layer and interface properties of the heterojunction.

Effect of zinc addition on properties of cadmium sulfide layer and performance of Cu(In,Ga)Se2 solar cell

International Nuclear Information System (INIS)

Bae, Dowon; Gho, Junghwan; Shin, Minjung; Kwon, Sehan

2013-01-01

Cd (1−x) Zn x S (CdS:Zn) thin films were grown on an indium tin oxide-coated glass substrate and Cu(In,Ga)Se 2 (CIGS) surface by chemical bath deposition for solar cell applications, and their composition, and optical properties were studied to decide the optimum process conditions for buffer layer growth. The average conversion efficiency of CIGS solar panels (24-in.) with the CdS:Zn layer was 0.35% higher than that of conventional solar panels mainly because of the increased open-circuit voltage. This efficiency improvement was not due to modification of the optical properties of the buffer layer, but due to the change in the deposition rate during buffer layer growth. - Highlights: ► CdS:Zn buffer layers were fabricated for Cu(In,Ga)Se 2 (CIGS) photovoltaic (PV) panels. ► Composition of buffer layers on indium–tin–oxide (ITO) and CIGS was investigated. ► Transmittance of CdS:Zn on ITO coated glass showed 5% higher than CdS. ► Efficiency of CdS:Zn solution adopted panels showed 0.47% higher than that with CdS. ► However, it was revealed that only Cd and S ions were found at the surface of CIGS

Fluid inclusion characteristics and geological significance of the Dajinshan W-Sn polymetallic deposit in Yunfu, Guangdong Province

Science.gov (United States)

Yu, Zhangfa; Chen, Maohong; Zhao, Haijie

2015-05-01

The Dajinshan tungsten-tin polymetallic deposit is a quartz-vein-type ore deposit located in Western Guangdong Province. The ore bodies show a fairly simple shape and mainly occur as tungsten-tin polymetallic-bearing sulfide quartz veins, including quartz vein, quartz-greisens, and sulfide quartz veins, and their distribution is spatially related to Dajinshan granitoids. The formation of the deposit experienced three stages: a wolframite-molybdenite-quartz stage, a wolframite-cassiterite-sulfide-quartz stage, and a fluorite-calcite-carbonate stage. Based on detailed petrographic observations, we conducted microthermometric and Raman microspectroscopic studies of fluid inclusions formed at different ore-forming stages in the Dajinshan tungsten-tin polymetallic deposit, identifying four dominant types of fluid inclusions: aqueous two-phase inclusions, CO2-bearing inclusions, solid or daughter mineral-bearing inclusions, and gas-rich inclusions. The gas compositions of ore-forming fluids in the Dajinshan tungsten-tin polymetallic deposit are mostly CO2, CH4, and H2O. The hydrogen, oxygen, and sulfur isotopic data imply that the ore-forming fluids in the Dajinshan tungsten-tin polymetallic deposit were mainly derived from magmatic fluids, mixed with meteoric water in the ore-formation process. These results indicate that the fluid mixing and boiling led to the decomposition of the metal complex in ore-forming fluids and ore deposition.

Dynamics of waterflooding massive oil deposits in the Chechen Ingush ASSR, including fissured reservoirs in the late stages of development

Energy Technology Data Exchange (ETDEWEB)

Tatashev, K.Kh.; Soboleva, G.N.; Tagunova, A.V.

1979-01-01

In 1956 in the Chechen Ingush ASSR a number of massive oil deposits located in fissured cavernous Upper Cretaceous limestone were developed. The deposits were developed by water-oil displacement from the edges and pericline toward the dome of the structure using the natural water pressure drive as well as artificial marginal flooding. The great oil-bearing capacity, the good hydrodynamic link with the deposit, the close magnitude of oil viscosity and water under the layer conditions and the significant difference in their density (0.4-0.5 g/cm/sup 3/) practically guarantees pistonlike oil displacement. Based on the deposit's geologic-physical characteristics, the late stage of development may be characterized by noncontinuous time and a sharp increase in well waterflooding to maintain full flooding. However, the data obtained from working the field suggest that a sharp increase in waterflooding will be substituted by a slow increase, by stabilization and possibly even a decrease in the percentage of water over the last 3-6 years. This occurred in a number of cases where measures were taken to limit the liquid flow, to periodically operate the well with isolated waterflooding and pereclinal perforation at intervals. This also occurred in a number of cases where the rate of fluid yield was naturally lowered by decreasing the number of producing wells due to waterflooding and disengagement. To more completely extract the oil from relatively low permeable areas of the deposits and to develop them in the later stages, it is useful to use a slow tempo once all wells have been brought to perclinal interval operation.

Zn{sub x}Cd{sub 1-} {sub x}S as a heterojunction partner for CuIn{sub 1-x}Ga{sub x}S{sub 2} thin film solar cells

Energy Technology Data Exchange (ETDEWEB)

Kumar, Bhaskar [Florida Solar Energy Center, University of Central Florida, Cocoa, FL 32922 (United States); Vasekar, Parag [Florida Solar Energy Center, University of Central Florida, Cocoa, FL 32922 (United States)], E-mail: psvasekar@yahoo.com; Pethe, Shirish A.; Dhere, Neelkanth G. [Florida Solar Energy Center, University of Central Florida, Cocoa, FL 32922 (United States); Koishiyev, Galymzhan T. [Physics Department, Colorado State University, Fort Collins, CO 80523 (United States)

2009-02-02

Zinc cadmium sulfide (Zn{sub x}Cd{sub 1-x}S) heterojunction partner layer prepared with chemical bath deposition (CBD) has exhibited better blue photon response and higher current densities due to its higher bandgap than that of conventional cadmium sulfide (CdS) layer for CuIn{sub 1-x}Ga{sub x}S{sub 2} (CIGS2) solar cells. CIGS2/Zn{sub x}Cd{sub 1-x}S devices have also shown higher open circuit voltage, V{sub oc} indicating improved junction properties. A conduction band offset has been observed by J-V curves at various temperatures indicating that still higher V{sub oc} can be obtained by optimizing the conduction band offset. This contribution discusses the effect of variation of parameters such as concentration of compounds, pH of solution and deposition time during CBD on device properties and composition and crystallinity of film. Efficiencies comparable to CIGS2/CdS devices have been achieved for CIGS2/Zn{sub x}Cd{sub 1-x}S devices.

Three-dimensional hydrodynamics of the deceleration stage in inertial confinement fusion

Energy Technology Data Exchange (ETDEWEB)

Weber, C. R., E-mail: weber30@llnl.gov; Clark, D. S.; Cook, A. W.; Eder, D. C.; Haan, S. W.; Hammel, B. A.; Hinkel, D. E.; Jones, O. S.; Marinak, M. M.; Milovich, J. L.; Patel, P. K.; Robey, H. F.; Salmonson, J. D.; Sepke, S. M.; Thomas, C. A. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States)

2015-03-15

The deceleration stage of inertial confinement fusion implosions is modeled in detail using three-dimensional simulations designed to match experiments at the National Ignition Facility. In this final stage of the implosion, shocks rebound from the center of the capsule, forming the high-temperature, low-density hot spot and slowing the incoming fuel. The flow field that results from this process is highly three-dimensional and influences many aspects of the implosion. The interior of the capsule has high-velocity motion, but viscous effects limit the range of scales that develop. The bulk motion of the hot spot shows qualitative agreement with experimental velocity measurements, while the variance of the hot spot velocity would broaden the DT neutron spectrum, increasing the inferred temperature by 400–800 eV. Jets of ablator material are broken apart and redirected as they enter this dynamic hot spot. Deceleration stage simulations using two fundamentally different rad-hydro codes are compared and the flow field is found to be in good agreement.

Three-dimensional hydrodynamics of the deceleration stage in inertial confinement fusion

International Nuclear Information System (INIS)

Weber, C. R.; Clark, D. S.; Cook, A. W.; Eder, D. C.; Haan, S. W.; Hammel, B. A.; Hinkel, D. E.; Jones, O. S.; Marinak, M. M.; Milovich, J. L.; Patel, P. K.; Robey, H. F.; Salmonson, J. D.; Sepke, S. M.; Thomas, C. A.

2015-01-01

The deceleration stage of inertial confinement fusion implosions is modeled in detail using three-dimensional simulations designed to match experiments at the National Ignition Facility. In this final stage of the implosion, shocks rebound from the center of the capsule, forming the high-temperature, low-density hot spot and slowing the incoming fuel. The flow field that results from this process is highly three-dimensional and influences many aspects of the implosion. The interior of the capsule has high-velocity motion, but viscous effects limit the range of scales that develop. The bulk motion of the hot spot shows qualitative agreement with experimental velocity measurements, while the variance of the hot spot velocity would broaden the DT neutron spectrum, increasing the inferred temperature by 400–800 eV. Jets of ablator material are broken apart and redirected as they enter this dynamic hot spot. Deceleration stage simulations using two fundamentally different rad-hydro codes are compared and the flow field is found to be in good agreement

Triassic regolithization: A major stage of pre-enrichment in the formation of unconformity related deposits in Southern France

International Nuclear Information System (INIS)

Schmitt, J.M.; Clement, J.Y.

1989-01-01

The formation of unconformity related uranium deposits in Canada and Australia is currently thought to have involved some stage of preconcentration within the Proterozoic regolith. Uranium deposits in the southern Massif central (France) are spatially linked to the Mesozoic unconformity. Under this unconformity, rocks of the Hercynian basement as well as Permo-Carboniferous sediments show a regolithic alteration dating back to the Late Permian to Late Triassic period. On the elevated parts of the Triassic landscape, 30 to 50 m deep weathering profiles are preserved. Three main zones can be distinguished: a lower pink coloured zone, showing partly albitized and chloritized rocks: a middle bleached zone with neogenic clays; and an upper reddish zone with Fe-Mn oxyhydroxides. Towards the Triassic basin, much deeper (200-300 m) alteration profiles are observed on Permo-Carboniferous sediments. The two upper regolithic zones are present, but the lower albitized one is very developed with two subzones: analcite/albite at the top, and K-feldspar/albite at the bottom. Geochemical data show that potassium is fixed in the uppermost horizons of the regolith, whereas sodium is transported towards the lower horizons and basin areas and fixed in analcite/albite zones. Uranium, vanadium, copper and less mobile elements such as titanium and zirconium are strongly leached from the weathering profiles in elevated parts of the landscape but are enriched in basin zones of albitization up to 5-15 times. Thus, solutions generated from the weathering profiles have brought about a major redistribution of uranium in the Triassic landscape. The remarkable applanation and tectonic stability of the area as well as a subarid climate seem to have favoured this 'regolithization' process. In southern France, geochemical differentiation during the Triassic has thus given rise to important uranium pre-enrichment, and the regolith is a major control for later uranium deposits. (author). 16 refs, 8

CIG-DB: the database for human or mouse immunoglobulin and T cell receptor genes available for cancer studies

Directory of Open Access Journals (Sweden)

Furue Motoki

2010-07-01

Full Text Available Abstract Background Immunoglobulin (IG or antibody and the T-cell receptor (TR are pivotal proteins in the immune system of higher organisms. In cancer immunotherapy, the immune responses mediated by tumor-epitope-binding IG or TR play important roles in anticancer effects. Although there are public databases specific for immunological genes, their contents have not been associated with clinical studies. Therefore, we developed an integrated database of IG/TR data reported in cancer studies (the Cancer-related Immunological Gene Database [CIG-DB]. Description This database is designed as a platform to explore public human and murine IG/TR genes sequenced in cancer studies. A total of 38,308 annotation entries for IG/TR proteins were collected from GenBank/DDBJ/EMBL and the Protein Data Bank, and 2,740 non-redundant corresponding MEDLINE references were appended. Next, we filtered the MEDLINE texts by MeSH terms, titles, and abstracts containing keywords related to cancer. After we performed a manual check, we classified the protein entries into two groups: 611 on cancer therapy (Group I and 1,470 on hematological tumors (Group II. Thus, a total of 2,081 cancer-related IG and TR entries were tabularized. To effectively classify future entries, we developed a computational method based on text mining and canonical discriminant analysis by parsing MeSH/title/abstract words. We performed a leave-one-out cross validation for the method, which showed high accuracy rates: 94.6% for IG references and 94.7% for TR references. We also collected 920 epitope sequences bound with IG/TR. The CIG-DB is equipped with search engines for amino acid sequences and MEDLINE references, sequence analysis tools, and a 3D viewer. This database is accessible without charge or registration at http://www.scchr-cigdb.jp/, and the search results are freely downloadable. Conclusions The CIG-DB serves as a bridge between immunological gene data and cancer studies, presenting

Hetero- and homogeneous three-dimensional hierarchical tungsten oxide nanostructures by hot-wire chemical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

Houweling, Z.S., E-mail: Silvester.Houweling@asml.com [Utrecht University, Debye Institute for Nanomaterials Science, Nanophotonics—Physics of Devices, Princetonlaan 4, 3584 CB Utrecht (Netherlands); Harks, P.-P.R.M.L.; Kuang, Y.; Werf, C.H.M. van der [Utrecht University, Debye Institute for Nanomaterials Science, Nanophotonics—Physics of Devices, Princetonlaan 4, 3584 CB Utrecht (Netherlands); Geus, J.W. [Utrecht University, Inorganic Chemistry and Catalysis, Padualaan 8, 3584 CH Utrecht (Netherlands); Schropp, R.E.I. [Utrecht University, Debye Institute for Nanomaterials Science, Nanophotonics—Physics of Devices, Princetonlaan 4, 3584 CB Utrecht (Netherlands)

2015-01-30

We present the synthesis of three-dimensional tungsten oxide (WO{sub 3−x}) nanostructures, called nanocacti, using hot-wire chemical vapor deposition. The growth of the nanocacti is controlled through a succession of oxidation, reduction and re-oxidation processes. By using only a resistively heated W filament, a flow of ambient air and hydrogen at subatmospheric pressure, and a substrate heated to about 700 °C, branched nanostructures are deposited. We report three varieties of simple synthesis approaches to obtain hierarchical homo- and heterogeneous nanocacti. Furthermore, by using catalyst nanoparticles site-selection for the growth is demonstrated. The atomic, morphological and crystallographic compositions of the nanocacti are determined using a combination of electron microscopy techniques, energy-dispersive X-ray spectroscopy and electron diffraction. - Highlights: • Continuous upscalable hot-wire CVD of 3D hierarchical nanocacti • Controllable deposition of homo- and heterogeneous WO{sub 3−x}/WO{sub 3−y} nanocacti • Introduction of three synthesis routes comprising oxidation, reduction and re-oxidation processes • Growth of periodic arrays of hetero- and homogeneous hierarchical 3D nanocacti.

Subject-independent emotion recognition based on physiological signals: a three-stage decision method.

Science.gov (United States)

Chen, Jing; Hu, Bin; Wang, Yue; Moore, Philip; Dai, Yongqiang; Feng, Lei; Ding, Zhijie

2017-12-20

Collaboration between humans and computers has become pervasive and ubiquitous, however current computer systems are limited in that they fail to address the emotional component. An accurate understanding of human emotions is necessary for these computers to trigger proper feedback. Among multiple emotional channels, physiological signals are synchronous with emotional responses; therefore, analyzing physiological changes is a recognized way to estimate human emotions. In this paper, a three-stage decision method is proposed to recognize four emotions based on physiological signals in the multi-subject context. Emotion detection is achieved by using a stage-divided strategy in which each stage deals with a fine-grained goal. The decision method consists of three stages. During the training process, the initial stage transforms mixed training subjects to separate groups, thus eliminating the effect of individual differences. The second stage categorizes four emotions into two emotion pools in order to reduce recognition complexity. The third stage trains a classifier based on emotions in each emotion pool. During the testing process, a test case or test trial will be initially classified to a group followed by classification into an emotion pool in the second stage. An emotion will be assigned to the test trial in the final stage. In this paper we consider two different ways of allocating four emotions into two emotion pools. A comparative analysis is also carried out between the proposal and other methods. An average recognition accuracy of 77.57% was achieved on the recognition of four emotions with the best accuracy of 86.67% to recognize the positive and excited emotion. Using differing ways of allocating four emotions into two emotion pools, we found there is a difference in the effectiveness of a classifier on learning each emotion. When compared to other methods, the proposed method demonstrates a significant improvement in recognizing four emotions in the

Systems and methods for solar cells with CIS and CIGS films made by reacting evaporated copper chlorides with selenium

Science.gov (United States)

Albin, David S.; Noufi, Rommel

2015-06-09

Systems and methods for solar cells with CIS and CIGS films made by reacting evaporated copper chlorides with selenium are provided. In one embodiment, a method for fabricating a thin film device comprises: providing a semiconductor film comprising indium (In) and selenium (Se) upon a substrate; heating the substrate and the semiconductor film to a desired temperature; and performing a mass transport through vapor transport of a copper chloride vapor and se vapor to the semiconductor film within a reaction chamber.

Three-phase bone scintigraphy: its contribution to diagnosing and staging avascular necrosis of the carpal lunate

International Nuclear Information System (INIS)

Kamburov, D.; Klisarova, A.

1998-01-01

Thirty-two patients with avascular necrosis of os lunatum (Kienbock's disease) were examined in three groups according to stage of the disease as follows: first - I stage of disease (10 cases); second - II stage (13) and third - III and IV stages (9). All patients underwent three-phase bone scintigraphy after i v injecting of 20 mCi 99m Tc-MDP. Blood pool index and skeletal index were duly calculated (normal value 1.15). Three-phase bone scintigraphy was within normal limits at 3 patients from the first group. Decreased values of perfusion and bone metabolism were obtained at 2 and 3 patients from the second and third group, respectively. Decreased perfusion and increased bone metabolism (skeletal index < 1.20) were found at 4 patients (group one), 6 (group two) and 3 (group three). Increased blood flow and enhanced uptake of tracer in the late phase were observed at one patient (group one), at 4 group two) and at 6 (group three). False negative results were documented in three cases (group one), and false positive - at one patient each from group two and three. The results show a high sensitivity (91%) of the method in Kienbock's disease and proves that three-phase bone scintigraphy may be used for staging avascular necrosis of the lunate bone. (author)

FURTHER STUDIES ON THE VARIATION OF SPRAY DEPOSITS IN VINEYARDS WITH AIRFLOW RATE AND VOLUME RATE

Directory of Open Access Journals (Sweden)

Emanuele Cerruto

2007-03-01

Full Text Available The present research, continuing that reported in [2], deals with the spray application subject, so to investigate as volume rate and airflow rate, forward speed being equal, affect the foliar deposition in an espalier vineyard. Experimental trials were carried out by means of an air assisted towed sprayer, equipped with “Albuz ATR” nozzles. To take into account the influence of the development of the trees, the field trials were replicated in two phenological stages with an interval of about one month: “Inflorescences fully developed” (stage 1 and “Beginning of berry touch” (stage 2. A full factorial experiment was carried out for each growth stage, with two airflow rates (3.9 and 7.5 m3/s, three volume rates (103, 216, and 276 L/ha in the first growth stage and 154, 330 and 432 L/ha in the second growth stage, and four replicates, arranged according to a randomised complete block design. Working pressure (1.2 MPa and forward speed (1.4 m/s were kept unchanged for all the trials. The foliar deposition was measured by means of a spectrophotometric technique. The leaves were sampled on two depth layers and two or three heights, according to the trees’ development. The results showed that volume rate did not significantly influence the mean foliar deposition in both the two growth stages, while the highest deposits were obtained with the lowest airflow rate. The airflow rate × volume rate interaction, though not statistically significant, showed that low volume rates together with high airflow rates, result in a noticeable reduction in foliar deposition (29% with respect the grand mean, due to an increase of the spry drift, especially at the first growth stage, when the foliar development is little. These second tests, unlike those described in [2], did not show any positive influence of the airflow rate on the foliar deposition in the inner part of the canopy, so further investigations could be necessary to better understand the

Preparation and layer-by-layer solution deposition of Cu(In,GaO2 nanoparticles with conversion to Cu(In,GaS2 films.

Directory of Open Access Journals (Sweden)

Walter J Dressick

Full Text Available We present a method of Cu(In,GaS2 (CIGS thin film formation via conversion of layer-by-layer (LbL assembled Cu-In-Ga oxide (CIGO nanoparticles and polyelectrolytes. CIGO nanoparticles were created via a novel flame-spray pyrolysis method using metal nitrate precursors, subsequently coated with polyallylamine (PAH, and dispersed in aqueous solution. Multilayer films were assembled by alternately dipping quartz, Si, and/or Mo substrates into a solution of either polydopamine (PDA or polystyrenesulfonate (PSS and then in the CIGO-PAH dispersion to fabricate films as thick as 1-2 microns. PSS/CIGO-PAH films were found to be inadequate due to weak adhesion to the Si and Mo substrates, excessive particle diffusion during sulfurization, and mechanical softness ill-suited to further processing. PDA/CIGO-PAH films, in contrast, were more mechanically robust and more tolerant of high temperature processing. After LbL deposition, films were oxidized to remove polymer and sulfurized at high temperature under flowing hydrogen sulfide to convert CIGO to CIGS. Complete film conversion from the oxide to the sulfide is confirmed by X-ray diffraction characterization.

Episodic response project: Wet deposition at watersheds in three regions of the eastern United States

International Nuclear Information System (INIS)

Barchet, W.R.

1991-11-01

During the period from August 1988 to June 1990, wet-only sampling of precipitation was carried out at three Episodic Response Project sites and at one supplemental site. The three watershed sites are Moss Lake, Biscuit Brook, and Linn Run. The supplemental site was the MAP3S site at Pennsylvania State University that characterizes the central group of northern Appalachian streams. The site operators adhered by varying degrees to the sample collection protocol based on the daily sampling protocol of the MAP3S Precipitation Chemistry Network. Sulfate and nitrate ion together accounted for more than 80% of total anions (in μEq/L) in the precipitation at all sites. Wet deposition of sulfate at Moss Lake, Biscuit Brook, Penn State, and Linn Run averaged 223, 230, 253, and 402 mg/m 2 /month, respectively, whereas nitrate wet deposition averaged 197, 195, 160, and 233 mg/m 2 /month, respectively. Sulfate deposition was a factor of 2 to 4 higher in summer than in winter. The seasonal pattern for nitrate deposition was weak; the seasonal contrast was less than a factor of 2.5 at all sites. The association between the wet deposition and precipitation chemistry at the MAP3S monitoring site and the average for the study watersheds was dependent on the distance between the site and watershed and the intervening terrain. Precipitation chemistry at the monitoring site is representative of that at the ERP study watersheds in the Adirondack and Catskill regions and in the south-western group of watersheds in the Appalachian region. High spatial variability in precipitation amounts makes this assumption weaker for wet deposition. Chemical input to watersheds from dry deposition has not been determined at any site but could range from a factor of 0.3 to 1.0 of the wet deposition. 7 refs., 38 figs., 12 tabs

An adaptive three-stage extended Kalman filter for nonlinear discrete-time system in presence of unknown inputs.

Science.gov (United States)

Xiao, Mengli; Zhang, Yongbo; Wang, Zhihua; Fu, Huimin

2018-04-01

Considering the performances of conventional Kalman filter may seriously degrade when it suffers stochastic faults and unknown input, which is very common in engineering problems, a new type of adaptive three-stage extended Kalman filter (AThSEKF) is proposed to solve state and fault estimation in nonlinear discrete-time system under these conditions. The three-stage UV transformation and adaptive forgetting factor are introduced for derivation, and by comparing with the adaptive augmented state extended Kalman filter, it is proven to be uniformly asymptotically stable. Furthermore, the adaptive three-stage extended Kalman filter is applied to a two-dimensional radar tracking scenario to illustrate the effect, and the performance is compared with that of conventional three stage extended Kalman filter (ThSEKF) and the adaptive two-stage extended Kalman filter (ATEKF). The results show that the adaptive three-stage extended Kalman filter is more effective than these two filters when facing the nonlinear discrete-time systems with information of unknown inputs not perfectly known. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Surface microstructure evolution of highly transparent and conductive Al-doped ZnO thin films and its application in CIGS solar cells

Science.gov (United States)

Cheng, Ke; Liu, Jingjing; Jin, Ranran; Liu, Jingling; Liu, Xinsheng; Lu, Zhangbo; Liu, Ya; Liu, Xiaolan; Du, Zuliang

2017-07-01

Aluminum-doped zinc oxide (AZO) has attained intensive attention as being a very good transparent conducting oxide for photovoltaic applications. In this work, AZO films have been deposited on glass substrate by radio frequency (RF) magnetron sputtering. The influences of substrate temperatures on morphological, structural, optical and electrical properties of AZO films were systematically investigated. The results indicate that all AZO films have the hexagonal structure with c-axis preferred orientation. Morphological and electrical measurements have revealed that the substrate temperatures have strong influence on the microstructure, optical and electrical properties of AZO films. The AZO film is highly transparent from ultraviolet up to near infrared range with highest average transparency exceeding 83%. The minimum resistivity is as low as 6.1 × 10-4 Ω cm. The carrier concentration and mobility are as high as 3.357 × 1020 cm-3 and 30.48 cm2/Vs, respectively. Finally, the performances of the AZO film are evaluated by its practical application in Cu(In1-xGax)Se2 (CIGS) photovoltaic device as a transparent electrode. Benefited from its highly transparent and conductive feature, the most efficient device reveals an efficiency of 7.8% with a short-circuit current density of 28.99 mA/cm2, an open-circuit voltage of 430 mV, and a fill factor of 62.44 under standard conditions.

Bismuth-doped Cu(In,Ga)Se{sub 2} absorber prepared by multi-layer precursor method and its solar cell

Energy Technology Data Exchange (ETDEWEB)

Chantana, Jakapan; Hironiwa, Daisuke; Minemoto, Takashi [Department of Electrical and Electronic Engineering, Ritsumeikan University, 1-1-1 Nojihigashi, Kusatsu, Shiga 525-8577 (Japan); Watanabe, Taichi; Teraji, Seiki; Kawamura, Kazunori [Environment and Energy Research Center, Nitto Denko Corporation, 2-8 Yamadaoka, Suita, Osaka 565-0871 (Japan)

2015-06-15

Bismuth (Bi)-doped Cu(In,Ga)Se{sub 2} (CIGS) films were prepared by the so-called ''multi-layer precursor method'', obtained by depositing them onto Bi layers with various thicknesses on Mo-coated soda-lime glass (SLG) substrates. Material composition (Cu, In, Ga, and Se) profiles of the CIGS films are almost identical, whereas sodium (Na) is reduced, when Bi thickness is increased. Moreover, the incorporation of Bi into the CIGS film is enhanced with thicker Bi layer. With Bi thickness from 0 to 70 nm, the 2.4-μm-thick CIGS absorbers demonstrate the increase in CIGS grain size, carrier lifetime, and carrier concentration, thus improving their cell performances, especially open-circuit voltage (V{sub OC}). With further increase in Bi thickness of above 70 nm, the CIGS films show the deterioration of CIGS film quality owing to the formation of Bi compounds such as Bi, BiSe, and Bi{sub 4}Se{sub 3}. Consequently, Bi-doped CIGS absorber with thickness of 2.4 μm, prepared with the 70-nm-thick Bi layer on Mo-coated SLG substrate, gives rise to the improvement of photovoltaic performances, especially V{sub OC}. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Bismuth-doped Cu(In,Ga)Se2 absorber prepared by multi-layer precursor method and its solar cell

International Nuclear Information System (INIS)

Chantana, Jakapan; Hironiwa, Daisuke; Minemoto, Takashi; Watanabe, Taichi; Teraji, Seiki; Kawamura, Kazunori

2015-01-01

Bismuth (Bi)-doped Cu(In,Ga)Se 2 (CIGS) films were prepared by the so-called ''multi-layer precursor method'', obtained by depositing them onto Bi layers with various thicknesses on Mo-coated soda-lime glass (SLG) substrates. Material composition (Cu, In, Ga, and Se) profiles of the CIGS films are almost identical, whereas sodium (Na) is reduced, when Bi thickness is increased. Moreover, the incorporation of Bi into the CIGS film is enhanced with thicker Bi layer. With Bi thickness from 0 to 70 nm, the 2.4-μm-thick CIGS absorbers demonstrate the increase in CIGS grain size, carrier lifetime, and carrier concentration, thus improving their cell performances, especially open-circuit voltage (V OC ). With further increase in Bi thickness of above 70 nm, the CIGS films show the deterioration of CIGS film quality owing to the formation of Bi compounds such as Bi, BiSe, and Bi 4 Se 3 . Consequently, Bi-doped CIGS absorber with thickness of 2.4 μm, prepared with the 70-nm-thick Bi layer on Mo-coated SLG substrate, gives rise to the improvement of photovoltaic performances, especially V OC . (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Palladium clusters deposited on the heterogeneous substrates

Energy Technology Data Exchange (ETDEWEB)

Wang, Kun, E-mail: cqdxwk@126.com [College of Power Engineering, Chongqing University, Chongqing 400044 (China); Key Laboratory of Low-grade Energy Utilization Technologies and Systems, Ministry of Education of PRC, Chongqing 400044 (China); Liu, Juanfang, E-mail: juanfang@cqu.edu.cn [College of Power Engineering, Chongqing University, Chongqing 400044 (China); Key Laboratory of Low-grade Energy Utilization Technologies and Systems, Ministry of Education of PRC, Chongqing 400044 (China); Chen, Qinghua, E-mail: qhchen@cqu.edu.cn [College of Power Engineering, Chongqing University, Chongqing 400044 (China); Key Laboratory of Low-grade Energy Utilization Technologies and Systems, Ministry of Education of PRC, Chongqing 400044 (China)

2016-07-15

Graphical abstract: The site-exchange between the substrate and cluster atoms can result in the formation of the surface alloys and the reconstruction of the cluster structure before the collision system approaching the thermal equilibrium. The deposited cluster adjusted the atom arrangement as possibly as to match the substrate lattice arrangement from bottom to up. The structural reconstruction is accompanied by the system potential energy minimization. - Highlights: • The deposition process can divide explicitly into three stages: adsorption, collision, relaxation. • The local melt does not emerge inside the substrate during the deposition process. • Surface alloys are formed by the site-exchange between the cluster and substrate atoms. • The cluster reconstructs the atom arrangement following as the substrate lattice arrangement from bottom to up. • The structural reconstruction ability and scope depend on the cluster size and incident energy. - Abstract: To improve the performance of the Pd composite membrane prepared by the cold spraying technology, it is extremely essential to give insights into the deposition process of the cluster and the heterogeneous deposition of the big Pd cluster at the different incident velocities on the atomic level. The deposition behavior, morphologies, energetic and interfacial configuration were examined by the molecular dynamic simulation and characterized by the cluster flattening ratio, the substrate maximum local temperature, the atom-embedded layer number and the surface-alloy formation. According to the morphology evolution, three deposition stages and the corresponding structural and energy evolution were clearly identified. The cluster deformation and penetrating depth increased with the enhancement of the incident velocity, but the increase degree also depended on the substrate hardness. The interfacial interaction between the cluster and the substrate can be improved by the higher substrate local temperature

Evaluating Self-Concept and Ego Status in Erikson's Last Three Psychosocial Stages.

Science.gov (United States)

Hamachek, Don

1990-01-01

Suggests behavioral criteria that can be used for assessing the status of self-concept and ego development in Erikson's last three psychosocial stages. Presents three tables of different behavioral expressions, each providing examples of possible behaviors and implicit attitudes related to positive and negative ego resolutions associated with last…

New data on the Geochemistry of Gases in the Potash Deposits

Directory of Open Access Journals (Sweden)

I. I. Chaykovskiy

2014-12-01

Full Text Available The composition of the gas phase of salt rocks from a number of potash deposits located in Europe (Verkhnekamskoe, Starobinskoe and Asia (Tubegatanskoe, Zhylyanskoe Satimolinskoe was studied. It allowed dividing them into two groups. In Asian deposits, only authigenic dry gases were formed by diagenetic decomposition of organic matter. Structural exposure of these deposits led to the oxidation of methane and hydrogen and enrichment by carbon dioxide. European deposits were not structurally exposed to the oxidation process, but were exposed during salt rock formation. They experienced influx of heavy hydrocarbons from the underlying strata. The history of the formation of gas regime at the Verkhnekamskoe potash deposit could be divided into three stages. First stage may be characterized by a syngenetic capture of deep gases and authigenic organic matter converted during diagenesis to methane, which percentage gradually increases with an increase of the thickness of impermeable salt strata. Then the deep gases invaded the salt formation during sedimentation of the upper carnallite layers and top salt rock. Third stage was associated with folding processes accompanied by a mobilization of fluids scattered in the gas-fluid inclusions, and with probable influx of heavy hydrocarbons and carbon dioxide resulted in formation of the secondary salt zones. Replacement of carnallite layers leads to the release of isomorphous ammonium ion and formation of a hydrogen.

Point contacts at the copper-indium-gallium-selenide interface—A theoretical outlook

Energy Technology Data Exchange (ETDEWEB)

Bercegol, Adrien, E-mail: adrien.bercegol@polytechnique.edu; Chacko, Binoy; Klenk, Reiner; Lauermann, Iver; Lux-Steiner, Martha Ch. [Helmholtz-Zentrum Berlin für Materialien und Energie, Albert Einstein Straße 15, 12489 Berlin (Germany); Liero, Matthias [Weierstraß-Institut für Angewandte Analysis und Stochastik, 10117 Berlin (Germany)

2016-04-21

For a long time, it has been assumed that recombination in the space-charge region of copper-indium-gallium-selenide (CIGS) is dominant, at least in high efficiency solar cells with low band gap. The recent developments like potassium fluoride post deposition treatment and point-contact junction may call this into question. In this work, a theoretical outlook is made using three-dimensional simulations to investigate the effect of point-contact openings through a passivation layer on CIGS solar cell performance. A large set of solar cells is modeled under different scenarios for the charged defect levels and density, radius of the openings, interface quality, and conduction band offset. The positive surface charge created by the passivation layer induces band bending and this influences the contact (CdS) properties, making it beneficial for the open circuit voltage and efficiency, and the effect is even more pronounced when coverage area is more than 95%, and also makes a positive impact on the device performance, even in the presence of a spike at CIGS/CdS heterojunction.

INFLUENCE OF NANOFILTRATION PRETREATMENT ON SCALE DEPOSITION IN MULTI-STAGE FLASH THERMAL DESALINATION PLANTS

Directory of Open Access Journals (Sweden)

Aiman E Al-Rawajfeh

2011-01-01

Full Text Available Scale formation represents a major operational problem encountered in thermal desalination plants. In current installed plants, and to allow for a reasonable safety margin, sulfate scale deposition limits the top brine temperature (TBT in multi-stage flash (MSF distillers up to 110-112oC. This has significant effect on the unit capital, operational and water production cost. In this work, the influence of nanofiltration (NF pretreatment on the scale deposition potential and increasing TBT in MSF thermal desalination plants is modeled on the basis of mass transfer with chemical reaction of solutes in the brine. Full and partial NF-pretreatment of the feed water were investigated. TBT can be increased in MSF by increasing the percentage of NF-treated feed. Full NF pretreatment of the make-up allows TBT in the MSF plant to be raised up to 175oC in the case of di hybrid NF-MSF and up to 165oC in the case of tri hybrid NF-RO-MSF. The significant scale reduction is associated with increasing flashing range, unit recovery, unit performance, and will lead to reduction in heat transfer surface area, pumping power and therefore, water production cost.

Difference in inhaled aerosol deposition patterns in the lungs due to three different sized aerosols

International Nuclear Information System (INIS)

Miki, M.; Isawa, T.; Teshima, T.; Anazawa, Y.; Motomiya, M.

1992-01-01

Deposition patterns of inhaled aerosol in the lungs were studied in five normal subjects and 20 patients with lung disease by inhaling radioaerosols with three different particle size distributions. Particle size distributions were 0.84, 1.04 and 1.93 μm in activity median aerodynamic diameter (AMAD) with its geometric standard deviation (σg) of 1.73, 1.71 and 1.52, respectively. Deposition patterns of inhaled aerosols were compared qualitatively and quantitatively by studying six different parameters: alveolar deposition ratio (ALDR), X max , X mean , standard deviation (S.D.), skewness and kurtosis of the radioactive distribution in the lungs following inhalation. It has been found that aerosol deposition patterns varied with particle size. The unevenness of aerosol deposition, X max , X mean and the number of 'hot spots' became more prominent with increase in particle size, whereas values of ALDR and S.D. decreased as particle size increased. (author)

Aerodynamic Analysis and Three-Dimensional Redesign of a Multi-Stage Axial Flow Compressor

Directory of Open Access Journals (Sweden)

Tao Ning

2016-04-01

Full Text Available This paper describes the introduction of three-dimension (3-D blade designs into a 5-stage axial compressor with multi-stage computational fluid dynamic (CFD methods. Prior to a redesign, a validation study is conducted for the overall performance and flow details based on full-scale test data, proving that the multi-stage CFD applied is a relatively reliable tool for the analysis of the follow-up redesign. Furthermore, at the near stall point, the aerodynamic analysis demonstrates that significant separation exists in the last stator, leading to the aerodynamic redesign, which is the focus of the last stator. Multi-stage CFD methods are applied throughout the three-dimensional redesign process for the last stator to explore their aerodynamic improvement potential. An unconventional asymmetric bow configuration incorporated with leading edge re-camber and re-solidity is employed to reduce the high loss region dominated by the mainstream. The final redesigned version produces a 13% increase in the stall margin while maintaining the efficiency at the design point.

Petrography, geochemistry and geochronology of the host porphyries and associated alteration at the Tuwu Cu deposit, NW China: a case for increased depositional efficiency by reaction with mafic hostrock?

Science.gov (United States)

Shen, Ping; Pan, Hongdi; Zhou, Taofa; Wang, Jingbin

2014-08-01

Tuwu is the largest porphyry copper deposit discovered in the Eastern Tianshan Mountains, Xinjiang, China. A newly recognized volcanic complex in the Early Carboniferous Qi'eshan Group at Tuwu consists of basalt, andesite, and diorite porphyry. The plagiogranite porphyry was emplaced into this complex at 332.8±2.5 Ma (U-Pb zircon SIMS determination). Whole-rock element geochemistry shows that the volcanic complex and plagiogranite porphyry formed in the same island arc, although the complex was derived by partial melting of the mantle wedge and the plagiogranite porphyry by partial melting of a subducting slab. The diorite and the plagiogranite porphyries have both been subjected to intense hydrothermal alteration and associated mineralization, but the productive porphyry is the plagiogranite porphyry. Three alteration and mineralization stages, including pre-, syn- and post-ore stages, have been recognized. The pre-ore stage formed a barren propylitic alteration which is widespread in the volcanic complex. The syn-ore stage is divided into three sub-stages: Stage 1 is characterized by potassic alteration with chalcopyrite + bornite + chalcocite; Stage 2 is marked by chlorite-sericite-albite alteration with chalcopyrite ± pyrite ± bornite; Stage 3 is represented by phyllic alteration with chalcopyrite + pyrite ± molybdenite. The post-ore stage produced a barren argillic alteration limited to the diorite porphyry. A specific feature of the Tuwu deposit is that the productive porphyry was emplaced into a very mafic package, and reaction of the resulting fluids with the ferrous iron-rich hostrocks was a likely reason that Tuwu is the largest porphyry in the district.

Coalescence of GaAs on (001) Si nano-trenches based on three-stage epitaxial lateral overgrowth

Energy Technology Data Exchange (ETDEWEB)

He, Yunrui; Wang, Jun, E-mail: wangjun12@bupt.edu.cn; Hu, Haiyang; Wang, Qi; Huang, Yongqing; Ren, Xiaomin [State Key Laboratory of Information Photonics and Optical Communications, Beijing University of Posts and Telecommunications, Beijing 100876 (China)

2015-05-18

The coalescence of selective area grown GaAs regions has been performed on patterned 1.8 μm GaAs buffer layer on Si via metal-organic chemical vapor deposition. We propose a promising method of three-stage epitaxial lateral overgrowth (ELO) to achieve uniform coalescence and flat surface. Rough surface caused by the coalescence of different growth fronts is smoothened by this method. Low root-mean-square surface roughness of 6.29 nm has been obtained on a 410-nm-thick coalesced ELO GaAs layer. Cross-sectional transmission electron microscope study shows that the coalescence of different growth fronts will induce some new dislocations. However, the coalescence-induced dislocations tend to mutually annihilate and only a small part of them reach the GaAs surface. High optical quality of the ELO GaAs layer has been confirmed by low temperature (77 K) photoluminescence measurements. This research promises a very large scale integration platform for the monolithic integration of GaAs-based device on Si.

Three-dimensional nanofabrication by electron-beam-induced deposition using 200-keV electrons in scanning transmission electron microscope

International Nuclear Information System (INIS)

Liu, Z.Q.; Mitsuishi, K.; Furuya, K.

2005-01-01

Attempts were made to fabricate three-dimensional nanostructures on and out of a substrate by electron-beam-induced deposition in a 200-kV scanning transmission electron microscope. Structures with parallel wires over the substrate surface were difficult to fabricate due to the direct deposition of wires on both top and bottom surfaces of the substrate. Within the penetration depth of the incident electron beam, nanotweezers were fabricated by moving the electron beam beyond different substrate layers. Combining the deposition of self-supporting wires and self-standing tips, complicated three-dimensional doll-like, flag-like, and gate-like nanostructures that extend out of the substrate were successfully fabricated with one-step or multi-step scans of the electron beam. Effects of coarsening, nucleation, and distortion during electron-beam-induced deposition are discussed. (orig.)

Three-stage enzymatic digestive system for a gut-on-a-chip

NARCIS (Netherlands)

de Haan, Pim; Ianovska, Margaryta A.; Mathwig, Klaus; Bouwmeester, Hans; Verpoorte, Elisabeth

2017-01-01

In this work, we present the development of a three-stage microfluidic system as a cell-free model for digestion in the human gastrointestinal (GI) tract. Larger-scale digestion models are currently being used for pharmacological, toxicological and nutritional studies to determine the possible

Investigation of aluminum and iron deposition on metaplastic bones in three patients with diffuse pulmonary ossification.

Science.gov (United States)

Ohtsuki, Yuji; Mori, Kousuke; Ohnishi, Hirozo; Enzan, Hideaki; Iguchi, Mitsuko; Lee, Gang-Hong; Furihata, Mutsuo

2015-12-01

Diffuse pulmonary ossification (DPO) is a rare pulmonary lesion. DPO is typically detected at autopsy rather than premortem. Recently, however, several cases were diagnosed antemortem using computed tomography, high-resolution computed tomography, or video-assisted thoracic surgery. In the present study, we evaluated DPO at autopsy from two patients with post-myocardial infarction (cases 1 and 3) and one patient with duodenal cancer (case 2). Multiple metaplastic bones (nodular in case 1 and 3 or dendriform in case 2) were detected in these three cases. In an attempt to detect aluminum and iron deposition in these metaplastic bones, histochemical investigations were performed. The two nodular types of one and three cases were positive for aluminum and iron, but the dendriform type of case 2 was positive only for aluminum. The depositions occurred in a linear pattern along the calcifying front. It is of great interest that these deposition patterns were similar to those of bones from three previously reported DPO cases and from the bones of hemodialysis patients. It is suggested that these abnormal metal depositions in the calcifying front might disturb the normal mineralization processes of the metaplastic bones, although no morphological abnormality was detected, except for dense black color of calcifying front lines. Further investigations are needed in more patients with DPO to obtain more information on this topic.

Correlation and stratigraphic eruption age of the pyroclastic flow deposits and wide spread volcanic ashes intercalated in the Pliocene-Pleistocene strata, central Japan

International Nuclear Information System (INIS)

Nagahashi, Yoshitaka; Satoguchi, Yasufumi; Yoshikawa, Shusaku

2000-01-01

Three pyroclastic flow deposits in the Takayama and Omine area, central Honshu, are correlated to the distal widespread volcanic ashes intercalated in the Plio-Pleistocene boundary strata in central Japan. The correlation is based on these stratigraphic relationships, facies, magnetostratigraphy, petrographic properties such as mineral assemblage, refractive index and chemical composition of the volcanic glasses and orthopyroxene. As the result of these correlation, the eruption age of the proximal pyroclastic flow deposits have become clear. And precise correlation between proximal eruption units and distal depositional units is now possible. Ho-Kd 39 Tephra erupted at about 1.76 Ma, forming a co-ignimbrite ash, which deposited in the Kanto sedimentary basin. Eb-Fukuda Tephra erupted at about 1.75 Ma, and distal volcaniclastic deposit sedimented in the Kinki, Niigata and Kanto sedimentary basins. The eruptional and depositional phase are divided into the stage 1, stage 2 (early), stage 2 (late) and stage 3. Stage 1 is phreato-plinian type eruption phase, forming distal ash fall deposit. Stage 2 (early) is plinian pumice fall, intra-plinian pyroclastic flow and plinian pumice fall eruption phase, forming distal ash fall. Stage 2 (late) is final eruptional phase of the biggest pyroclastic flow of the Eb-Fukuda Tephra, forming a co-ignimbrite ash fall. Stage 3 is resedimented stage after the end of the explosive eruption. It is notable that resedimented volcaniclastic deposit reached Osaka sedimentary basin 300 km away from the eruption center. Om-SK110 Tephra erupted at about 1.65 Ma, divided into the stage 1, stage 2 and stage 3. Stage 1 is eruption phase of the plinian pumice fall and first pyroclastic flow. Stage 2 is pauses in eruption activity. Stage 3 is second pyroclastic flow phase, it is inferred that the pyroclastic flow of the stage 3 directly entered the Niigata sedimentary basin and simultaneously formed a co-ignimbrite ash. (author)

Geological and geochemical studies of the Shujiadian porphyry Cu deposit, Anhui Province, Eastern China: Implications for ore genesis

Science.gov (United States)

Wang, Shiwei; Zhou, Taofa; Yuan, Feng; Fan, Yu; White, Noel C.; Lin, Fengjie

2015-05-01

Most porphyry deposits in the world occur in magmatic arc settings and are related to subduction of oceanic plates. A small proportion of porphyry deposits occur in intracontinental settings, however they are still poorly understood. Shujiadian, a newly-discovered porphyry Cu deposit, is located in the Middle-Lower Yangtze River Valley metallogenic belt and belongs to the intracontinental class. The deposit has classic alteration zones defined by a core of potassic alteration and local Ca-silicate alteration, which is overprinted by a feldspar-destructive alteration zone and cut by veins containing epidote and chlorite. Wallrocks of the deposit are unreactive quartz-rich sedimentary rocks. Three main paragenetic stages have been recognized based on petrographic observations; silicate stage, quartz-sulfide stage, and sulfide-carbonate stage. Quartz + pyrite + chalcopyrite ± molybdenite veins, and quartz + chalcopyrite + pyrite veins of the quartz-sulfide stage contribute most of the copper, and chalcopyrite + chlorite ± pyrite ± pyrrhotite ± quartz ± illite veins of the sulfide-carbonate stage also contribute part of the copper; all the mineralized veins are associated with feldspar-destructive alteration. Investigations on the fluid inclusions in Shujiadian indicate that the ore-forming fluids had four evolutionary episodes: immiscibility and overpressure in the silicate stage, boiling in the quartz-sulfide stage and mixing with meteoric water in the sulfide-carbonate stage. Sulfur and strontium isotope studies suggest that ore metals were mainly derived from magmatic-hydrothermal fluids, and combined with our study of fluid inclusions, we infer that decompression, changes in oxygen fugacity and sulfur content were the main factors that caused Cu precipitation. Compared with porphyry deposits in magmatic arc settings, there are some differences in the ore-bearing rock, alteration, and the composition of ore-forming fluids.

Ultrafast pump-probe reflectance spectroscopy: Why sodium makes Cu(In,Ga)Se2 solar cells better

KAUST Repository

Eid, Jessica; Usman, Anwar; Gereige, Issam; Duren, Jeroen Van; Lyssenko, Vadim; Leo, Karl; Mohammed, Omar F.

2015-01-01

Although Cu(In,Ga)Se2 (CIGS) solar cells have the highest efficiency of any thin-film solar cell, especially when sodium is incorporated, the fundamental device properties of ultrafast carrier transport and recombination in such cells remain not fully understood. Here, we explore the dynamics of charge carriers in CIGS absorber layers with varying concentrations of Na by femtosecond (fs) broadband pump-probe reflectance spectroscopy with 120 fs time resolution. By analyzing the time-resolved transient spectra in a different time domain, we show that a small amount of Na integrated by NaF deposition on top of sputtered Cu(In,Ga) prior to selenization forms CIGS, which induces slower recombination of the excited carriers. Here, we provide direct evidence for the elongation of carrier lifetimes by incorporating Na into CIGS.

Ultrafast pump-probe reflectance spectroscopy: Why sodium makes Cu(In,Ga)Se2 solar cells better

KAUST Repository

Eid, Jessica

2015-04-14

Although Cu(In,Ga)Se2 (CIGS) solar cells have the highest efficiency of any thin-film solar cell, especially when sodium is incorporated, the fundamental device properties of ultrafast carrier transport and recombination in such cells remain not fully understood. Here, we explore the dynamics of charge carriers in CIGS absorber layers with varying concentrations of Na by femtosecond (fs) broadband pump-probe reflectance spectroscopy with 120 fs time resolution. By analyzing the time-resolved transient spectra in a different time domain, we show that a small amount of Na integrated by NaF deposition on top of sputtered Cu(In,Ga) prior to selenization forms CIGS, which induces slower recombination of the excited carriers. Here, we provide direct evidence for the elongation of carrier lifetimes by incorporating Na into CIGS.

Investigating the electronic properties of Al{sub 2}O{sub 3}/Cu(In,Ga)Se{sub 2} interface

Energy Technology Data Exchange (ETDEWEB)

Kotipalli, R., E-mail: raja.kotipalli@uclouvain.be; Rajkumar, R.; Flandre, D. [ICTEAM, Université catholique de Louvain, Louvain-la-Neuve, 1348 (Belgium); Vermang, B., E-mail: bart.vermang@imec.be [Ångström Solar Center, University of Uppsala, Uppsala, 75121 (Sweden); ESAT-KU Leuven, University of Leuven, Leuven, 3001 (Belgium); IMEC, Kapeldreef 75, Leuven, 3001 (Belgium); Joel, J.; Edoff, M. [Ångström Solar Center, University of Uppsala, Uppsala, 75121 (Sweden)

2015-10-15

Atomic layer deposited (ALD) Al{sub 2}O{sub 3} films on Cu(In,Ga)Se{sub 2} (CIGS) surfaces have been demonstrated to exhibit excellent surface passivation properties, which is advantageous in reducing recombination losses at the rear metal contact of CIGS thin-film solar cells. Here, we report, for the first time, experimentally extracted electronic parameters, i.e. fixed charge density (Q{sub f}) and interface-trap charge density (D{sub it}), for as-deposited (AD) and post-deposition annealed (PDA) ALD Al{sub 2}O{sub 3} films on CIGS surfaces using capacitance–voltage (C-V) and conductance-frequency (G-f) measurements. These results indicate that the AD films exhibit positive fixed charges Q{sub f} (approximately 10{sup 12} cm{sup −2}), whereas the PDA films exhibit a very high density of negative fixed charges Q{sub f} (approximately 10{sup 13} cm{sup −2}). The extracted D{sub it} values, which reflect the extent of chemical passivation, were found to be in a similar range of order (approximately 10{sup 12} cm{sup −2} eV{sup −1}) for both AD and PDA samples. The high density of negative Q{sub f} in the bulk of the PDA Al{sub 2}O{sub 3} film exerts a strong Coulomb repulsive force on the underlying CIGS minority carriers (n{sub s}), preventing them to recombine at the CIGS/Al{sub 2}O{sub 3} interface. Using experimentally extracted Q{sub f} and D{sub it} values, SCAPS simulation results showed that the surface concentration of minority carriers (n{sub s}) in the PDA films was approximately eight-orders of magnitude lower than in the AD films. The electrical characterization and estimations presented in this letter construct a comprehensive picture of the interfacial physics involved at the Al{sub 2}O{sub 3}/CIGS interface.

Soil erosion and deposition in the new shorelines of the Three Gorges Reservoir.

Science.gov (United States)

Su, Xiaolei; Nilsson, Christer; Pilotto, Francesca; Liu, Songping; Shi, Shaohua; Zeng, Bo

2017-12-01

During the last few decades, the construction of storage reservoirs worldwide has led to the formation of many new shorelines in former upland areas. After the formation of such shorelines, a dynamic phase of soil erosion and deposition follows. We explored the factors regulating soil dynamics in the shorelines of the Three Gorges Reservoir (TGR) on the Yangtze River in China. We selected four study sites on the main stem and three on the tributaries in the upstream parts of the reservoir, and evaluated whether the sites close to the backwater tail (the point at which the river meets the reservoir) had more soil deposition than the sites far from the backwater tail. We also tested whether soil erosion differed between the main stem and the tributaries and across shorelines. We found that soil deposition in the new shorelines was higher close to the backwater tail and decreased downstream. Soil erosion was higher in the main stem than in the tributaries and higher at lower compared to higher shoreline altitudes. In the tributaries, erosion did not differ between higher and lower shoreline levels. Erosion increased with increasing fetch length, inundation duration and distance from the backwater tail, and decreased with increasing soil particle fineness. Our results provide a basis for identifying shorelines in need of restorative or protective measures. Copyright © 2017 Elsevier B.V. All rights reserved.

Condensation Enhancement by Surface Porosity: Three-Stage Mechanism.

Science.gov (United States)

Yarom, Michal; Marmur, Abraham

2015-08-18

Surface defects, such as pores, cracks, and scratches, are naturally occurring and commonly found on solid surfaces. However, the mechanism by which such imperfections promote condensation has not been fully explored. In the current paper we thermodynamically analyze the ability of surface porosity to enhance condensation on a hydrophilic solid. We show that the presence of a surface-embedded pore brings about three distinct stages of condensation. The first is capillary condensation inside the pore until it is full. This provides an ideal hydrophilic surface for continuing the condensation. As a result, spontaneous condensation and wetting can be achieved at lower vapor pressure than on a smooth surface.

Diamond-like carbon films deposited on three-dimensional shape substrate model by liquid electrochemical technique

International Nuclear Information System (INIS)

He, Y.Y.; Zhang, G.F.; Zhao, Y.; Liu, D.D.; Cong, Y.; Buck, V.

2015-01-01

Diamond-like carbon (DLC) films were deposited on three-dimensional (3D) shape substrate model by electrolysis of 2-propanol solution at low temperature (60 °C). This 3D shape model was composed of a horizontally aligned stainless steel wafer and vertically aligned stainless steel rods. Morphology and microstructure of the films were analyzed by scanning electron microscopy (SEM), atomic force microscopy (AFM) and Raman spectroscopy, respectively. The results suggested there were only differences in film uniformity and thickness for two kinds of samples. The hydrogenated amorphous carbon films deposited on horizontally aligned substrate were smooth and homogeneous. And the film thickness of DLC films gained on the vertical substrates decreased along vertical direction. It is believed that bubble formation could enhance nucleation on the wetted capillary area. This experiment shows that deposition of DLC films by liquid phase deposition on 3D shape conductive substrates is possible. - Highlights: • DLC film is expected to be deposited on complex surface/shape substrate. • DLC film is deposited on 3D shape substrate by liquid electrochemical method. • Horizontal substrate is covered by smooth and homogeneous DLC films. • Film thickness decreases along vertical direction due to boiling effect

Diamond-like carbon films deposited on three-dimensional shape substrate model by liquid electrochemical technique

Energy Technology Data Exchange (ETDEWEB)

He, Y.Y. [Institute of Nano-photonics, School of Physics and Materials Engineering, Dalian Nationalities University, 116600 Dalian (China); Zhang, G.F. [School of Materials Science and Engineering, Dalian University of Technology, 116024, Dalian China (China); Zhao, Y.; Liu, D.D. [Institute of Nano-photonics, School of Physics and Materials Engineering, Dalian Nationalities University, 116600 Dalian (China); Cong, Y., E-mail: congyan@ciomp.ac.cn [Institute of Nano-photonics, School of Physics and Materials Engineering, Dalian Nationalities University, 116600 Dalian (China); Buck, V. [Thin Film Technology Group, Faculty of Physics, University Duisburg-Essen and CeNIDE, 47057 Duisburg (Germany)

2015-09-01

Diamond-like carbon (DLC) films were deposited on three-dimensional (3D) shape substrate model by electrolysis of 2-propanol solution at low temperature (60 °C). This 3D shape model was composed of a horizontally aligned stainless steel wafer and vertically aligned stainless steel rods. Morphology and microstructure of the films were analyzed by scanning electron microscopy (SEM), atomic force microscopy (AFM) and Raman spectroscopy, respectively. The results suggested there were only differences in film uniformity and thickness for two kinds of samples. The hydrogenated amorphous carbon films deposited on horizontally aligned substrate were smooth and homogeneous. And the film thickness of DLC films gained on the vertical substrates decreased along vertical direction. It is believed that bubble formation could enhance nucleation on the wetted capillary area. This experiment shows that deposition of DLC films by liquid phase deposition on 3D shape conductive substrates is possible. - Highlights: • DLC film is expected to be deposited on complex surface/shape substrate. • DLC film is deposited on 3D shape substrate by liquid electrochemical method. • Horizontal substrate is covered by smooth and homogeneous DLC films. • Film thickness decreases along vertical direction due to boiling effect.

Tracking the first two seconds: three stages of visual information processing?

Science.gov (United States)

Jacob, Jane; Breitmeyer, Bruno G; Treviño, Melissa

2013-12-01

We compared visual priming and comparison tasks to assess information processing of a stimulus during the first 2 s after its onset. In both tasks, a 13-ms prime was followed at varying SOAs by a 40-ms probe. In the priming task, observers identified the probe as rapidly and accurately as possible; in the comparison task, observers determined as rapidly and accurately as possible whether or not the probe and prime were identical. Priming effects attained a maximum at an SOA of 133 ms and then declined monotonically to zero by 700 ms, indicating reliance on relatively brief visuosensory (iconic) memory. In contrast, the comparison effects yielded a multiphasic function, showing a maximum at 0 ms followed by a minimum at 133 ms, followed in turn by a maximum at 240 ms and another minimum at 720 ms, and finally a third maximum at 1,200 ms before declining thereafter. The results indicate three stages of prime processing that we take to correspond to iconic visible persistence, iconic informational persistence, and visual working memory, with the first two used in the priming task and all three in the comparison task. These stages are related to stages presumed to underlie stimulus processing in other tasks, such as those giving rise to the attentional blink.

Comparative Analysis of Flower Volatiles from Nine Citrus at Three Blooming Stages

Directory of Open Access Journals (Sweden)

Muhammad Azam

2013-11-01

Full Text Available Volatiles from flowers at three blooming stages of nine citrus cultivars were analyzed by headspace-solid phase microextraction (HS-SPME-GC-MS. Up to 110 volatiles were detected, with 42 tentatively identified from citrus flowers for the first time. Highest amounts of volatiles were present in fully opened flowers of most citrus, except for pomelos. All cultivars were characterized by a high percentage of either oxygenated monoterpenes or monoterpene hydrocarbons, and the presence of a high percentage of nitrogen containing compounds was also observed. Flower volatiles varied qualitatively and quantitatively among citrus types during blooming. Limonene was the most abundant flower volatile only in citrons; α-citral and β-citral ranked 2nd and 3rd only for Bergamot, and unopened flowers of Ponkan had a higher amount of linalool and β-pinene while much lower amount of γ-terpinene and p-cymene than Satsuma. Taking the average of all cultivars, linalool and limonene were the top two volatiles for all blooming stages; β-pinene ranked 3rd in unopened flowers, while indole ranked 3rd for half opened and fully opened flower volatiles. As flowers bloomed, methyl anthranilate increased while 2-hexenal and p-cymene decreased. In some cases, a volatile could be high in both unopened and fully opened flowers but low in half opened ones. Through multivariate analysis, the nine citrus cultivars were clustered into three groups, consistent with the three true citrus types. Furthermore, an influence of blooming stages on clustering was observed, especially with hybrids Satsuma and Huyou. Altogether, it was suggested that flower volatiles can be suitable markers for revealing the genetic relationships between citrus cultivars but the same blooming stage needs to be strictly controlled.

Multiple episodes of mineralization revealed by Re-Os molybdenite geochronology in the Lala Fe-Cu deposit, SW China

Science.gov (United States)

Zhu, Zhimin; Tan, Hongqi; Liu, Yingdong; Li, Chao

2018-03-01

The Lala Fe-Cu deposit is one of the largest iron oxide-copper-gold (IOCG) deposits in the Kangdian copper belt, southwest China. The paragenetic sequence of the Lala deposit includes six hydrothermal stages: pre-ore pervasive Na alteration (I); magnetite stage with K-feldspar and apatite (II); polymetallic disseminated/massive magnetite-sulfide stage (III); banded magnetite-sulfide stage (IV); sulfide vein stage (V); and late quartz-carbonate vein stage (VI). Fifteen molybdenite separates from stages III to VI were analyzed for Re-Os dating. Our new Re-Os data, together with previous studies, identify four distinct hydrothermal events at the Lala deposit. Molybdenite from the stage III disseminated to massive chalcopyrite-magnetite ores yielded a weighted average Re-Os age of 1306 ± 8 Ma (MSWD = 1.1, n = 6) which represents the timing of main ore formation. Molybdenite from the stage IV-banded magnetite-chalcopyrite ores yielded a weighted average Re-Os age of 1086 ± 8 Ma (MSWD = 2.2, n = 7), i.e., a second ore-forming event. Molybdenite from the stage V sulfide veins yielded a weighted average Re-Os age of 988 ± 8 Ma (MSWD = 1.3, n = 7) which represents the timing of a third hydrothermal event. Molybdenite from the quartz-carbonate veins (stage VI) yielded a weighted average Re-Os age at 835 ± 4 Ma (MSWD = 0.66, n = 10) and documented the timing of a late hydrothermal event. Our results indicate that the Lala deposit formed during multiple, protracted mineralization events over several hundred million years. The first three Mesoproterozoic mineralization events are coeval with intra-continental rifting (breakup of the supercontinent Nuna) and share a temporal link to other IOCG-style deposits within the Kangdian Copper Belt, and the last Neoproterozoic hydrothermal event is coeval with the Sibao orogeny which culminated with the amalgamation of the Yangtze Block with the Cathaysia Block at 860-815 Ma.

Post-annealing effects on pulsed laser deposition-grown GaN thin films

International Nuclear Information System (INIS)

Cheng, Yu-Wen; Wu, Hao-Yu; Lin, Yu-Zhong; Lee, Cheng-Che; Lin, Ching-Fuh

2015-01-01

In this work, the post-annealing effects on gallium nitride (GaN) thin films grown from pulsed laser deposition (PLD) are investigated. The as-deposited GaN thin films grown from PLD are annealed at different temperatures in nitrogen ambient. Significant changes of the GaN crystal properties are observed. Raman spectroscopy is used to observe the crystallinity, the change of residual stress, and the thermal decomposition of the annealed GaN thin films. X-ray diffraction is also applied to identify the crystal phase of GaN thin films, and the surface morphology of GaN thin films annealed at different temperatures is observed by scanning electron microscopy. Through the above analyses, the GaN thin films grown by PLD undergo three stages: phase transition, stress alteration, and thermal decomposition. At a low annealing temperature, the rock salt GaN in GaN films is transformed into wurtzite. The rock salt GaN diminishes with increasing annealing temperature. At a medium annealing temperature, the residual stress of the film changes significantly from compressive strain to tensile strain. As the annealing temperature further increases, the GaN undergoes thermal decomposition and the surface becomes granular. By investigating the annealing temperature effects and controlling the optimized annealing temperature of the GaN thin films, we are able to obtain highly crystalline and strain-free GaN thin films by PLD. - Highlights: • The GaN thin film is grown on sapphire by pulsed laser deposition. • The GaN film undergoes three stages with increasing annealing temperature. • In the first stage, the film transfers from rock salt to wurtzite phase. • In the second stage, the stress in film changes from compressive to tensile. • In the final stage, the film thermally decomposes and becomes granular

Numerical simulation of a three-stage stirling-type pulse-tube refrigerator

Energy Technology Data Exchange (ETDEWEB)

Etaati, M.A.

2011-06-22

The pulse-tube refrigerator (PTR) is a rather new device for cooling down to extremely low temperatures, i.e. below 4 K. The PTR works by the cyclic compression and expansion of helium that flows through a regenerator made of porous material, a cold heat exchanger, a tube, a hot heat exchanger and an orifice, in series. In a Stirling-type PTR compression and expansion are generated by a piston. The compression increases the temperature of the helium in the tube and makes it flow towards the orifice; the expansion decreases the temperature and makes the helium flow backwards to the regenerator. The net effect of warmer helium flowing in one direction and colder helium in the opposite direction is that of cooling power at the cold heat exchanger. Three PTRs are inter-connected aiming to obtain the desired 4 K lowest temperature. The conservation laws of mass, momentum and energy, and an equation of state, are simplified using asymptotic analysis based on low Mach-numbers. The regenerator is modelled one-dimensionally with Darcy's law for flow resistance. The tube is modelled either one-dimensionally without resistance or two-dimensionally with axisymmetric laminar viscous flow. The heat transfer in the porous medium of the regenerator and in the solid tube wall is taken into account. The gas can be either ideal or real. All the material properties, including viscosity and conductivity, are taken temperature and pressure dependent. Three single-stage PTRs are connected with the regenerators in series and the tubes in parallel and six flow possibilities at the junctions are considered. Three by-passes (double-inlets) are used to enhance and tune the performance. The governing equations are numerically solved with a finite-difference method of nominally second-order accuracy in space and time. Pressure correction, flux limiter, 1D-2D connections and domain decomposition are the keywords here. Special attention is paid to suitable initial conditions, high resolution

Ecofriendly and Nonvacuum Electrostatic Spray-Assisted Vapor Deposition of Cu(In,Ga)(S,Se)2 Thin Film Solar Cells.

Science.gov (United States)

Hossain, Md Anower; Wang, Mingqing; Choy, Kwang-Leong

2015-10-14

Chalcopyrite Cu(In,Ga)(S,Se)2 (CIGSSe) thin films have been deposited by a novel, nonvacuum, and cost-effective electrostatic spray-assisted vapor deposition (ESAVD) method. The generation of a fine aerosol of precursor solution, and their controlled deposition onto a molybdenum substrate, results in adherent, dense, and uniform Cu(In,Ga)S2 (CIGS) films. This is an essential tool to keep the interfacial area of thin film solar cells to a minimum value for efficient charge separation as it helps to achieve the desired surface smoothness uniformity for subsequent cadmium sulfide and window layer deposition. This nonvacuum aerosol based approach for making the CIGSSe film uses environmentally benign precursor solution, and it is cheaper for producing solar cells than that of the vacuum-based thin film solar technology. An optimized CIGSSe thin film solar cell with a device configuration of molybdenum-coated soda-lime glass substrate/CIGSSe/CdS/i-ZnO/AZO shows the photovoltaic (j-V) characteristics of Voc=0.518 V, jsc=28.79 mA cm(-2), fill factor=64.02%, and a promising power conversion efficiency of η=9.55% under simulated AM 1.5 100 mW cm(-2) illuminations, without the use of an antireflection layer. This demonstrates the potential of ESAVD deposition as a promising alternative approach for making thin film CIGSSe solar cells at a lower cost.

Grid Integration of Single Stage Solar PV System using Three-level Voltage Source Converter

Science.gov (United States)

Hussain, Ikhlaq; Kandpal, Maulik; Singh, Bhim

2016-08-01

This paper presents a single stage solar PV (photovoltaic) grid integrated power generating system using a three level voltage source converter (VSC) operating at low switching frequency of 900 Hz with robust synchronizing phase locked loop (RS-PLL) based control algorithm. To track the maximum power from solar PV array, an incremental conductance algorithm is used and this maximum power is fed to the grid via three-level VSC. The use of single stage system with three level VSC offers the advantage of low switching losses and the operation at high voltages and high power which results in enhancement of power quality in the proposed system. Simulated results validate the design and control algorithm under steady state and dynamic conditions.

Spatial Patterns and Interspecific Associations of Three Canopy Species at Different Life Stages in a Subtropical Forest,China

Institute of Scientific and Technical Information of China (English)

Lin Li; Shi-Guang Wei; Zhong-Liang Huang; Wan-Hui Ye; Hong-Lin Cao

2008-01-01

Spatial patterns of species at different life stages are an important aspect for understanding causal mechanisms that facilitate species co-existence.Using Ripley's univariate L(t) and bivariate L12(t) functions,we analyzed the spatial patterns and interspecific associations of three canopy species at different life history stages in a 20-ha subtropical forest plot in Dinghushan Nature Reserve.Based on diameter at breast height (DBH),four life stages were distinguished.Castanopsis chinensis and Schima superba showed a unimodal DBH distribution.Engelhardtia roxburghiana showed a bimodal curve.L(t) function analysis showed significantly aggregated distributions of all three species at later life stages and random distribution at early life stages at some scales.From the analysis of L12(t) function,the results showed the positive association was a dominant pattern for most species pairs at most scales but the intensity of association decreases with the increase of life stages.Juveniles of the three species had no negative intra- and interspecific associations with the older life stages.Only premature trees were suppressed by overmature trees at some scales.Considering these results,we found three canopy-dominant species that lacked regeneration.There was no direct competition occurring between understorey individuals.Young trees can grow well under conspecific species with two other species.Longevity and lack of regeneration led to a large number of trees stored in mature and overmature stages,therefore,intra-and inter-competition can be strong at later life stages.

A new three-stage method for solving unit commitment problem

Energy Technology Data Exchange (ETDEWEB)

Khanmohammadi, S.; Amiri, M.; Haque, M. Tarafdar [Faculty of Electrical and Computer Engineering, University of Tabriz, P.O. Box 51665-343, Tabriz (Iran)

2010-07-15

This paper presents a new Three-Stage (THS) approach for solving Unit Commitment (UC) problem. The proposed method has a simple procedure to get at favorite solutions in a feasible duration of time by producing a primal schedule of status of units at the first step. In the second step the operating units take hourly values by doing Economic Dispatch (ED) on them via a hybrid serial algorithm of Artificial Intelligence (AI) including Particle Swarm Optimization (PSO) and Nelder-Mead (NM) algorithms. In spite of the acceptable solutions obtained by these two stages, the presented method takes another step called the solution modification process (SMP) to reach a more suitable solution. The simulation results over some standard cases of UC problem confirm that this method produces robust solutions and generally gets appropriate near-optimal solutions. (author)

Successful three stage repair of a large congenital abdominal region defect

Directory of Open Access Journals (Sweden)

Vaidehi Agrawal

2015-06-01

Full Text Available We present two infants born with large, right upper quadrant defects which cannot be categorized as either a gastroschisis or omphalocele. We successfully managed one infant with a three stage repair using polytetrafluoroethylene (PTFE patch, porcine urinary bladder matrix (UBM and delayed surgical closure. The second infant passed away due to parental consent care withdrawal.

Characteristics of Bilayer Molybdenum Films Deposited Using RF Sputtering for Back Contact of Thin Film Solar Cells

Directory of Open Access Journals (Sweden)

Sea-Fue Wang

2014-01-01

Full Text Available Mo films prepared under a single deposition condition seldom simultaneously obtain a low resistivity and a good adhesion necessary for use in solar cells. In order to surmount the obstacle, bilayer Mo films using DC sputtering at a higher working pressure and a lower working pressure have been attempted as reported in the literature. In this study, RF sputtering with different powers in conjunction with different working pressures was explored to prepare bilayer Mo film. The first bottom layer was grown at a RF sputtering power of 30 W and a working pressure of 12 mTorr, and the second top layer was deposited at 100 W and 4.5 mTorr. The films revealed a columnar growth with a preferred orientation along the (110 plane. The bilayer Mo films reported an electrical resistivity of 6.35 × 10−5 Ω-cm and passed the Scotch tape test for adhesion to the soda-lime glass substrate, thereby qualifying the bilayer Mo films for use as back metal contacts for CIGS substrates.

A preventive maintenance model with a two-level inspection policy based on a three-stage failure process

International Nuclear Information System (INIS)

Wang, Wenbin; Zhao, Fei; Peng, Rui

2014-01-01

Inspection is always an important preventive maintenance (PM) activity and can have different depths and cover all or part of plant systems. This paper introduces a two-level inspection policy model for a single component plant system based on a three-stage failure process. Such a failure process divides the system′s life into three stages: good, minor defective and severe defective stages. The first level of inspection, the minor inspection, can only identify the minor defective stage with a certain probability, but can always reveal the severe defective stage. The major inspection can however identify both defective stages perfectly. Once the system is found to be in the minor defective stage, a shortened inspection interval is adopted. If however the system is found to be in the severe defective stage, we may delay the maintenance action if the time to the next planned PM window is less than a threshold level, but otherwise, replace immediately. This corresponds to the well adopted maintenance policy in practice such as periodic inspections with planned PMs. A numerical example is presented to demonstrate the proposed model by comparing with other models. - Highlights: • The system′s deterioration goes through a three-stage process, namely, normal, minor defective and severe defective. • Two levels of inspections are proposed, e.g., minor and major inspections. • Once the minor defective stage is found, instead of taking a maintenance action, a shortened inspection interval is recommended. • When the severe defective stage is found, we delay the maintenance according to the threshold to the next PM. • The decision variables are the inspection intervals and the threshold to PM

A screening questionnaire for convulsive seizures: A three-stage field-validation in rural Bolivia.

Science.gov (United States)

Giuliano, Loretta; Cicero, Calogero Edoardo; Crespo Gómez, Elizabeth Blanca; Padilla, Sandra; Bruno, Elisa; Camargo, Mario; Marin, Benoit; Sofia, Vito; Preux, Pierre-Marie; Strohmeyer, Marianne; Bartoloni, Alessandro; Nicoletti, Alessandra

2017-01-01

Epilepsy is one of the most common neurological diseases in Latin American Countries (LAC) and epilepsy associated with convulsive seizures is the most frequent type. Therefore, the detection of convulsive seizures is a priority, but a validated Spanish-language screening tool to detect convulsive seizures is not available. We performed a field validation to evaluate the accuracy of a Spanish-language questionnaire to detect convulsive seizures in rural Bolivia using a three-stage design. The questionnaire was also administered face-to-face, using a two-stage design, to evaluate the difference in accuracy. The study was carried out in the rural communities of the Gran Chaco region. The questionnaire consists of a single screening question directed toward the householders and a confirmatory section administered face-to-face to the index case. Positive subjects underwent a neurological examination to detect false positive and true positive subjects. To estimate the proportion of false negative, a random sample of about 20% of the screened negative underwent a neurological evaluation. 792 householders have been interviewed representing a population of 3,562 subjects (52.2% men; mean age 24.5 ± 19.7 years). We found a sensitivity of 76.3% (95% CI 59.8-88.6) with a specificity of 99.6% (95% CI 99.4-99.8). The two-stage design showed only a slightly higher sensitivity respect to the three-stage design. Our screening tool shows a good accuracy and can be easily used by trained health workers to quickly screen the population of the rural communities of LAC through the householders using a three-stage design.

The Three Stages of Critical Policy Methodology: An Example from Curriculum Analysis

Science.gov (United States)

Rata, Elizabeth

2014-01-01

The article identifies and discusses three stages in the critical policy methodology used in the sociology of education. These are: firstly, employing a political economy theoretical framework that identifies causal links between global forces and local developments; secondly, analysing educational policy within that theoretically conceptualised…

EffiCiency and Safety of an eLectronic cigAreTte (ECLAT as tobacco cigarettes substitute: a prospective 12-month randomized control design study.

Directory of Open Access Journals (Sweden)

Pasquale Caponnetto

Full Text Available Electronic cigarettes (e-cigarettes are becoming increasingly popular with smokers worldwide. Users report buying them to help quit smoking, to reduce cigarette consumption, to relieve tobacco withdrawal symptoms, and to continue having a 'smoking' experience, but with reduced health risks. Research on e-cigarettes is urgently needed in order to ensure that the decisions of regulators, healthcare providers and consumers are based on science. Methods ECLAT is a prospective 12-month randomized, controlled trial that evaluates smoking reduction/abstinence in 300 smokers not intending to quit experimenting two different nicotine strengths of a popular e-cigarette model ('Categoria'; Arbi Group Srl, Italy compared to its non-nicotine choice. GroupA (n = 100 received 7.2 mg nicotine cartridges for 12 weeks; GroupB (n = 100, a 6-week 7.2 mg nicotine cartridges followed by a further 6-week 5.4 mg nicotine cartridges; GroupC (n = 100 received no-nicotine cartridges for 12 weeks. The study consisted of nine visits during which cig/day use and exhaled carbon monoxide (eCO levels were measured. Smoking reduction and abstinence rates were calculated. Adverse events and product preferences were also reviewed.Declines in cig/day use and eCO levels were observed at each study visits in all three study groups (p<0.001 vs baseline, with no consistent differences among study groups. Smoking reduction was documented in 22.3% and 10.3% at week-12 and week-52 respectively. Complete abstinence from tobacco smoking was documented in 10.7% and 8.7% at week-12 and week-52 respectively. A substantial decrease in adverse events from baseline was observed and withdrawal symptoms were infrequently reported during the study. Participants' perception and acceptance of the product under investigation was satisfactory.In smokers not intending to quit, the use of e-cigarettes, with or without nicotine, decreased cigarette consumption and elicited enduring tobacco

Insights into cadmium diffusion mechanisms in two-stage diffusion profiles in solar-grade Cu(In,Ga)Se2 thin films

International Nuclear Information System (INIS)

Biderman, N. J.; Sundaramoorthy, R.; Haldar, Pradeep; Novak, Steven W.; Lloyd, J. R.

2015-01-01

Cadmium diffusion experiments were performed on polished copper indium gallium diselenide (Cu(In,Ga)Se 2 or CIGS) samples with resulting cadmium diffusion profiles measured by time-of-flight secondary ion mass spectroscopy. Experiments done in the annealing temperature range between 275 °C and 425 °C reveal two-stage cadmium diffusion profiles which may be indicative of multiple diffusion mechanisms. Each stage can be described by the standard solutions of Fick's second law. The slower cadmium diffusion in the first stage can be described by the Arrhenius equation D 1  = 3 × 10 −4  exp (− 1.53 eV/k B T) cm 2  s −1 , possibly representing vacancy-meditated diffusion. The faster second-stage diffusion coefficients determined in these experiments match the previously reported cadmium diffusion Arrhenius equation of D 2  = 4.8 × 10 −4  exp (−1.04 eV/k B T) cm 2  s −1 , suggesting an interstitial-based mechanism

Three-stage steady-state model for biomass gasification in a dual circulating fluidized-bed

International Nuclear Information System (INIS)

Nguyen, Thanh D.B.; Ngo, Son Ich; Lim, Young-Il; Lee, Jeong Woo; Lee, Uen-Do; Song, Byung-Ho

2012-01-01

Highlights: ► Steam gasification of woodchips is examined in dual circulating fluidized-bed (DFB). ► We develop a three-stage model (TSM) for process performance evaluation. ► Effect of gasification temperature and steam to fuel ratio is investigated. ► Several effective operating conditions are found by parametric study. - Abstract: A three-stage steady state model (TSM) was developed for biomass steam gasification in a dual circulating fluidized-bed (DFB) to calculate the composition of producer gas, carbon conversion, heat recovery, cost efficiency, and heat demand needed for the endothermic gasification reactions. The model was divided into three stages including biomass pyrolysis, char–gas reactions, and gas–phase reaction. At each stage, an empirical equation was estimated from experimental data. It was assumed that both unconverted char and additional fuel were completely combusted at 950 °C in the combustor (riser) and the heat required for gasification reactions was provided by the bed material (silica sand). The model was validated with experimental data taken from the literature. The parametric study of the gasification temperature (T) and the steam to fuel ratio (γ) was then carried out to evaluate performance criteria of a 1.8 MW DFB gasifier using woodchips as a feedstock for the electric power generation. Effective operating conditions of the DFB gasifier were proposed by means of the contour of the solid circulation ratio, the heat recovery, the additional fuel ratio and the cost efficiency with respect to T and γ.

Geological characteristics of the main deposits in the world. Geological characteristics of French uranium deposits; their consequences on the different stages of valorisation. The uranium market

International Nuclear Information System (INIS)

Gangloff, A.; Lenoble, A.; Mabile, J.

1958-07-01

This document gathers three contributions. In the first one, after having recalled data regarding uranium ore and metal reserves in Canada, USA, South Africa and France, the author describes and discusses the geological and mineral characteristics of the main deposits in Canada (Great Bear Lake, Ace-Verna and other deposits of the Beaverlodge district, Gunnar, Blind River and Bancroft), in the USA (New Mexico, Colorado and Arizona), and in South Africa (similar structure as observed in Blind River). The second contribution addresses the French uranium deposits by firstly presenting, describing and classifying vein deposits (five types are distinguished) and sedimentary deposits in different geological formations, and by secondly discussing the impacts of these characteristics on exploration, surface exploration works, and mining works. The third contribution proposes an overview of the uranium market: comments of world productions (conventional extraction processes and technical peculiarities, costs and prices, reserves and production in Canada, USA, South Africa, France, Australia and others), presentation of the French program (location and production capacity of uranium production plants, locations of ore extraction), overview of the current situation of the world market (price levels, possible prices after 1962), discussion of the comparison between demands and supplies, overview of the French uranium policy

A Three-Stage Mechanistic Model for Solidification Cracking During Welding of Steel

Science.gov (United States)

Aucott, L.; Huang, D.; Dong, H. B.; Wen, S. W.; Marsden, J.; Rack, A.; Cocks, A. C. F.

2018-03-01

A three-stage mechanistic model for solidification cracking during TIG welding of steel is proposed from in situ synchrotron X-ray imaging of solidification cracking and subsequent analysis of fracture surfaces. Stage 1—Nucleation of inter-granular hot cracks: cracks nucleate inter-granularly in sub-surface where maximum volumetric strain is localized and volume fraction of liquid is less than 0.1; the crack nuclei occur at solute-enriched liquid pockets which remain trapped in increasingly impermeable semi-solid skeleton. Stage 2—Coalescence of cracks via inter-granular fracture: as the applied strain increases, cracks coalesce through inter-granular fracture; the coalescence path is preferential to the direction of the heat source and propagates through the grain boundaries to solidifying dendrites. Stage 3—Propagation through inter-dendritic hot tearing: inter-dendritic hot tearing occurs along the boundaries between solidifying columnar dendrites with higher liquid fraction. It is recommended that future solidification cracking criterion shall be based on the application of multiphase mechanics and fracture mechanics to the failure of semi-solid materials.

Comprehensive perspective on the mechanism of preferred orientation in reactive-sputter-deposited nitrides

International Nuclear Information System (INIS)

Kajikawa, Yuya; Noda, Suguru; Komiyama, Hiroshi

2003-01-01

Texture control of sputter-deposited nitride films has provoked a great deal of interest due to its technological importance. Despite extensive research, however, the reported results are scattered and discussions about the origin of preferred orientation (PO) are sometimes conflicting, and therefore controversial. The aim of this study is to acquire a clear perspective in order to discuss the origin of PO of sputter-deposited nitrides. Among nitrides, we focus on titanium nitride (TiN), aluminum nitride (AlN), and tantalum nitride (TaN), which are three commonly used nitrides. First, we collected reported experimental results about the relation between operating conditions and PO, because PO is considered to be determined by film formation processes, such as surface diffusion or grain growth, which is affected by operating conditions. We also collected reported results about such PO-determining processes. Then, we categorized the PO-determining processes into an initial stage and a growth stage of film deposition, and further categorized each stage into a vapor-solid interface and a solid-solid interface. Then, we related each stage and interface to film morphology and to PO-determining processes. Finally, based on existing results, previous models, and proposed schema, we discuss the origin of PO. Based on previous experimental results on film morphology, PO of nitride films occurred in the growth stage at the vapor-solid interface, where the sticking process of the precursor and the surface diffusion process determine PO, rather than in the initial stage and in the growth stage at the solid-solid interface. TiN (002) PO, however, seems to be caused in the initial stage at the solid-solid interface

Improving Performance of CIGS Solar Cells by Annealing ITO Thin Films Electrodes

Directory of Open Access Journals (Sweden)

Chuan Lung Chuang

2015-01-01

Full Text Available Indium tin oxide (ITO thin films were grown on glass substrates by direct current (DC reactive magnetron sputtering at room temperature. Annealing at the optimal temperature can considerably improve the composition, structure, optical properties, and electrical properties of the ITO film. An ITO sample with a favorable crystalline structure was obtained by annealing in fixed oxygen/argon ratio of 0.03 at 400°C for 30 min. The carrier concentration, mobility, resistivity, band gap, transmission in the visible-light region, and transmission in the near-IR regions of the ITO sample were -1.6E+20 cm−3, 2.7E+01 cm2/Vs, 1.4E-03 Ohm-cm, 3.2 eV, 89.1%, and 94.7%, respectively. Thus, annealing improved the average transmissions (400–1200 nm of the ITO film by 16.36%. Moreover, annealing a copper-indium-gallium-diselenide (CIGS solar cell at 400°C for 30 min in air improved its efficiency by 18.75%. The characteristics of annealing ITO films importantly affect the structural, morphological, electrical, and optical properties of ITO films that are used in solar cells.

Deuterium markers in CdS and Zn(O,S) buffer layers deposited by solution growth for Cu(In,Ga)Se{sub 2} thin-film solar cells

Energy Technology Data Exchange (ETDEWEB)

Witte, Wolfram; Eicke, Axel; Hariskos, Dimitrios [Zentrum fuer Sonnenenergie und Wasserstoff-Forschung Baden-Wuerttemberg (ZSW), Stuttgart (Germany); Souza, Roger A. de; Martin, Manfred [Institute of Physical Chemistry, RWTH Aachen University (Germany)

2017-12-15

This contribution describes an easy and cheap approach to introduce deuterium (D) as an isotopic marker into the commonly used buffer layer materials CdS and Zn(O,S) for Cu(In,Ga)Se{sub 2} (CIGS) thin-film solar cells. D was successfully incorporated during the growth of Zn(O,S) and CdS buffer layers by chemical bath deposition (CBD) with D{sub 2}O. CIGS solar cells prepared with D-containing buffers grown by CBD exhibit power conversion efficiencies above 16%, that is, the D content has no detrimental effect on the performance or other solar cell parameters of the devices. With depth profiles obtained by time-of-flight secondary ion mass spectrometry (ToF-SIMS) we clearly detect the intentionally incorporated D within the solution-grown Zn(O,S) buffer. Assuming that D is present as OD, we compare the amount of OD within the Zn(O,S) layer with the amount of OH on the surface of the subsequent sputtered (Zn,Mg)O layer. Possible applications and future experiments of the method inserting isotopic markers such as D in functional layers of chalcopyrite-type thin-film solar cells and beyond are discussed. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Effect of Dust Deposition on Yield and Yield Components of Chickpea (Cicer arietinum L. under Rain Fed and Supplemental Irrigation Conditions in Kermanshah

Directory of Open Access Journals (Sweden)

hamze felegari

2017-10-01

Full Text Available Introduction Dust storms over Middle East are one of the most important environmental and pollution problems. In order to assess the effects of dust deposition and supplemental irrigation on yield and yield components of chickpea, an experiment was conducted at the research farm of Agriculture and Natural Resources Campus of Razi University, Kermanshah, in 2013-2014 growing season based on RCDB with three replicatins. Treatments of the experiment included supplemental irrigation as the main plot factor with 2 levels (No-irrigation and irrigation at poding stage. and dust deposition as the sub plot factor with7 levels (Control, dust application at vegetative stage, dust application at poding stage, dust application at pod filling stage, Washing at the end of vegetative stage, Washing at the end of poding stage and Washing at the end of vegetative and poding stages.Supplemental irrigation and dust deposition had significant effect on yield and yield components of chickpea. Drought stress reduced yield and yield components. With dust application at vegetative stage (67.86 g.m-2, poding stage (79.37 g.m-2 and pod filling (79.52 g.m-2 seed yield reduced. With Washing leaves at the end of vegetative and poding stages seed yield (85.20 g.m-2 increased. Materials and Methods This study was conducted during 2013-2014 at the research Farm of Razi university in Kermanshah state in the west of Iran (47º 9′ E and 34º 21′ N, 1319 meters above sea level. The soil of the research area was clay loam (36.1% clay, 30.7% silt and was cultivated with chickpea previously. Treatments included supplemental irrigation as the main plot at 2 levels (control (non-irrigation and irrigation at poding stage. Other treatments included dust deposition as the sub plot at 7 levels (Control (non-treatment, dust application at vegetative stage, dust application at poding stage, dust application at pod filling stage, Washing at the end of vegetative stage, Washing at the end

Comparison of beam deposition for three neutral beam injection codes

International Nuclear Information System (INIS)

Wieland, R.M.; Houlberg, W.A.; Mense, A.T.

1979-03-01

The three neutral beam injection codes BEAM (Houlberg, ORNL), HOFR (Howe, ORNL), and FREYA (Post, PPPL) are compared with respect to the calculation of the fast ion deposition profile H(r). Only plasmas of circular cross section are considered, with injection confined to the mid-plane of the torus. The approximations inherent in each code are pointed out, and a series of comparisons varying several parameters (beam energy and radius, machine size, and injection angle) shows excellent agreement among all the codes. A cost comparison (execution time and memory requirements) is made which points out the relative merits of each code within the context of incorporation into a plasma transport simulation code

Single stage three level grid interactive MPPT inverter for PV systems

International Nuclear Information System (INIS)

Ozdemir, Saban; Altin, Necmi; Sefa, Ibrahim

2014-01-01

Highlights: • A three phase three-level NPC inverter for grid interactive PV systems is proposed. • A novel MPPT algorithm is introduced for single stage systems. • The proposed algorithm is robust with respect to parameter variations of PV system. • THD level is measured as 3.45% and it meets the international standards (<5%). • Total system efficiency is measured as 93.08%. - Abstract: In this study, three-phase, single stage neutral point clamped grid interactive inverter is designed and implemented. The reference current of the voltage source inverter is determined by maximum power point tracking sub-program in order to obtain maximum power from photovoltaic modules instantaneously. Proposed control is realized via TMS320F28335 32-bit floating point processor. The modified incremental conductance method is applied for maximum power point tracking; the PI regulator is used to control the inverter output current shape and level. Galvanic isolation is provided by a line frequency transformer that matches inverter output voltage to the grid voltage level and prevents DC current injection into the grid. Experimental results show that the designed inverter imports energy to the grid with unity power factor, total harmonic distortion level is 3.45% and this value is in the limits of the international standards. In addition, the total efficiency of the system is measured as 93.08%. The proposed system gets the maximum power from photovoltaic module and dispatches into the grid without using additional DC/DC converter

Experimental investigation of ash deposits characteristics of co-combustion of coal and rice hull using a digital image technique

International Nuclear Information System (INIS)

Qiu, Kunzan; Zhang, Hailong; Zhou, Hao; Zhou, Bin; Li, Letian; Cen, Kefa

2014-01-01

This paper investigated the ash deposit characteristics during the co-firing Da Tong (DA) coal with different proportions of rice hull (0%, 5%, 10%, and 20%, based on weight) in a pilot-scale furnace. The growth of ash deposit with a four-stage mode was presented. The stable thickness values of DA coal, 5% rice hull, 10% rice hull, and 20% rice hull were 0.5, 1.4, 2.9, 5.7 cm, with stable heat flux values of 230, 200, 175, and 125 kW/m 2 , respectively. According to the results of scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX), the amount of Si in the deposits increased with the increasing proportion of rice hull rich in SiO 2 . The X-ray diffraction (XRD) analysis results indicated that most elements except Si were in the amorphous state because of the formation of eutectics. The stable thicknesses of deposits increased exponentially with the proportion of rice hull. The deposit was loose, easy removable but it reduced the heat transfer significantly. Consequently, sootblowing timely was necessary when co-firing DA coal with rice hull. - Highlights: • Digital image technique was used to monitor deposits growth process. • A type of four stages mode of ash deposit growth was presented. • The heat flux of ash deposits fit a three-stage mode. • The addition of rice hull increased the porosity of deposits

Hypofractionated three-dimensional conformal radiotherapy for medically inoperable early stage

Energy Technology Data Exchange (ETDEWEB)

Lee, Joo Ho; Wu, Hong Gyun; KIm, Hak Jae; Park, Charn Il; Lee, Se Hoon; Kim, Dong Wan; Heo, Dae Seong [Seoul National University College of Medicine, Seou (Korea, Republic of)

2013-01-15

The purpose of this study was to assess the clinical outcomes of hypofractionated radiotherapy (HFRT) with three-dimensional conformal technique for medically inoperable patients with early stage non-small-cell lung cancer (NSCLC) and to evaluate prognostic factors. We performed a retrospective review of 26 patients who underwent HFRT for early stage NSCLC between September 2005 and August 2011. Only clinical stage T1-3N0 was included. The median RT dose was 70 Gy (range, 60 to 72 Gy) and the median biologically equivalent dose (BED) was 94.5 Gy (range, 78.0 to 100.8 Gy). In 84.6% of patients, 4 Gy per fraction was used. Neoadjuvant chemotherapy with paclitaxel and cisplatin was given to 2 of 26 patients. The median follow-up time for surviving patients was 21 months (range, 13 to 49 months). The overall response rate was 53.9%, and the initial local control rate was 100%. The median survival duration was 27.8 months. Rates of 2-year overall survival, progression-free survival (PFS), local control (LC), and locoregional-free survival (LRFS) were 54.3%, 61.1%, 74.6%, and 61.9%, respectively. Multivariate analysis showed that BED (>90 vs. {<=}90 Gy) was an independent prognostic factor influencing PFS, LC, and LRFS. Severe toxicities over grade 3 were not observed. Radical HFRT can yield satisfactory disease control with acceptable rates of toxicities in medically inoperable patients with early stage NSCLC. HFRT is a viable alternative for clinics and patients ineligible for stereotactic ablative radiotherapy. BED over 90 Gy and 4 Gy per fraction might be appropriate for HFRT.

The Effects of Annealing Parameters on the Crystallization and Morphology of Cu(In,GaSe2 Absorber Layers Prepared by Annealing Stacked Metallic Precursors

Directory of Open Access Journals (Sweden)

Chia-Ho Huang

2014-01-01

Full Text Available CIGS films are prepared by single-stage annealing of the solid Se-coated In/Cu-Ga bilayer precursor. The annealing processes were performed using various Ar pressures, heating rates, and soaking times. A higher Ar pressure is needed to fabricate highly crystalline CIGS films, as no extra Se-vapor source is supplied. As the heating rate increases, the surface morphologies of the CIGS films become looser and some cracks are observed. However, the influence of soaking time is insignificant and the selenization process only requires a short time when the precursors are selenized at a higher temperature with a lower heating rate and a higher Ar pressure. In this study, a dense chalcopyrite CIGS film with a thickness of about 1.5-1.6 μm, with large grains (~1.2 μm and no cracking or peeling is obtained after selenizing at a temperature of 550°C, an Ar pressure of 300 Torr, a heating rate of 60°C/min, and a soaking time of 20 min. By adequate design of the stacked precursor and controlling the annealing parameters, single-stage annealing of the solid Se-coated In/Cu-Ga bilayer precursor is simplified for the fabrication of a fully crystallized chalcopyrite CIGS absorber layers with good crystallization and large grains.

A Three-Stage Optimal Approach for Power System Economic Dispatch Considering Microgrids

Directory of Open Access Journals (Sweden)

Wei-Tzer Huang

2016-11-01

Full Text Available The inclusion of microgrids (MGs in power systems, especially distribution-substation-level MGs, significantly affects power systems because of the large volumes of import and export power flows. Consequently, power dispatch has become complicated, and finding an optimal solution is difficult. In this study, a three-stage optimal power dispatch model is proposed to solve such dispatch problems. In the proposed model, the entire power system is divided into two parts, namely, the main power grid and MGs. The optimal power dispatch problem is resolved on the basis of multi-area concepts. In stage I, the main power system economic dispatch (ED problem is solved by sensitive factors. In stage II, the optimal power dispatches of the local MGs are addressed via an improved direct search method. In stage III, the incremental linear models for the entire power system can be established on the basis of the solutions of the previous two stages and can be subjected to linear programming to determine the optimal reschedules from the original dispatch solutions. The proposed method is coded using Matlab and tested by utilizing an IEEE 14-bus test system to verify its feasibility and accuracy. Results demonstrated that the proposed approach can be used for the ED of power systems with MGs as virtual power plants.

The Association of Parent Mindfulness with Parenting and Youth Psychopathology Across Three Developmental Stages.

Science.gov (United States)

Parent, Justin; McKee, Laura G; N Rough, Jennifer; Forehand, Rex

2016-01-01

The primary purpose of the current study was to test a model examining the process by which parent dispositional mindfulness relates to youth psychopathology through mindful parenting and parenting practices. The universality of the model across youth at three developmental stages was examined: young childhood (3-7 years; n = 210), middle childhood (8-12 years; n = 200), and adolescence (13-17 years; n = 205). Overall, participants were 615 parents (55% female) and one of their 3-to-17 year old children (45% female). Parents reported on their dispositional mindfulness, mindful parenting, positive and negative parenting practices and their child's or adolescent's internalizing and externalizing problems. Consistent findings across all three developmental stages indicated that higher levels of parent dispositional mindfulness were indirectly related to lower levels of youth internalizing and externalizing problems through higher levels of mindful parenting and lower levels of negative parenting practices. Replication of these findings across families with children at different developmental stages lends support to the generalizability of the model.

Characteristics of molybdenum bilayer back contacts for Cu(In,Ga)Se{sub 2} solar cells on Ti foils

Energy Technology Data Exchange (ETDEWEB)

Roger, Charles, E-mail: charles.rgr@gmail.com [CEA, LITEN, 17 Rue des Martyrs, 38054 Grenoble Cedex 9 (France); Noël, Sébastien; Sicardy, Olivier; Faucherand, Pascal; Grenet, Louis; Karst, Nicolas; Fournier, Hélène; Roux, Frédéric [CEA, LITEN, 17 Rue des Martyrs, 38054 Grenoble Cedex 9 (France); Ducroquet, Frédérique [IMEP-LAHC, Minatec, Grenoble-INP, CNRS UMR 5130, 38016 Grenoble (France); Brioude, Arnaud [Laboratoire des Multimatériaux et Interfaces, UMR 5615, Villeurbanne (France); Perraud, Simon [CEA, LITEN, 17 Rue des Martyrs, 38054 Grenoble Cedex 9 (France)

2013-12-02

Molybdenum back contact properties are critical for Cu(In,Ga)Se{sub 2} (CIGS) solar cell performance on metallic substrates. In this work, we investigated the properties of sputter-deposited Mo bilayer back contacts on Ti foils. The morphology, electrical resistivity, optical reflectance and residual mechanical stress of the bottom Mo layer were modified by varying the working pressure during its deposition. Working pressures ranging from 0.27 Pa to 4.00 Pa were used. The top Mo layer was deposited using constant conditions at a pressure of 0.13 Pa. It was demonstrated that unlike a Mo monolayer, the use of a Mo bilayer allows controlling the mechanical stress at the Mo/CIGS interface without degrading the optical reflectance and the electrical resistance of the back contact. It was also found that the morphology of the bottom Mo layer affects the growth of the top Mo layer, resulting in a modified back contact surface morphology. This induces changes in the crystalline orientation of the CIGS layer. The resulting solar cell characteristics strongly vary as a function of the bottom Mo layer deposition pressure. A bottom Mo layer growth at 2.93 Pa allows improving the solar cell conversion efficiency by 1.5 times compared to a bottom Mo layer deposited at 0.27 Pa. Using the improved Mo bilayer back contact, a maximum solar cell efficiency of 10.0% was obtained without sodium addition nor anti-reflection coating. - Highlights: • Mo bilayer back contacts for Cu(In,Ga)Se{sub 2} solar cells were grown on Ti substrates. • The sputtering pressure of the bottom Mo layer was varied between 0.27 Pa and 4 Pa. • The top Mo layer controls the optical and electrical properties of the back contact. • The structure of the bottom Mo layer influences the morphology of the top Mo layer. • The back contact affects the CIGS texture, device series resistance and efficiency.

Characteristics of molybdenum bilayer back contacts for Cu(In,Ga)Se2 solar cells on Ti foils

International Nuclear Information System (INIS)

Roger, Charles; Noël, Sébastien; Sicardy, Olivier; Faucherand, Pascal; Grenet, Louis; Karst, Nicolas; Fournier, Hélène; Roux, Frédéric; Ducroquet, Frédérique; Brioude, Arnaud; Perraud, Simon

2013-01-01

Molybdenum back contact properties are critical for Cu(In,Ga)Se 2 (CIGS) solar cell performance on metallic substrates. In this work, we investigated the properties of sputter-deposited Mo bilayer back contacts on Ti foils. The morphology, electrical resistivity, optical reflectance and residual mechanical stress of the bottom Mo layer were modified by varying the working pressure during its deposition. Working pressures ranging from 0.27 Pa to 4.00 Pa were used. The top Mo layer was deposited using constant conditions at a pressure of 0.13 Pa. It was demonstrated that unlike a Mo monolayer, the use of a Mo bilayer allows controlling the mechanical stress at the Mo/CIGS interface without degrading the optical reflectance and the electrical resistance of the back contact. It was also found that the morphology of the bottom Mo layer affects the growth of the top Mo layer, resulting in a modified back contact surface morphology. This induces changes in the crystalline orientation of the CIGS layer. The resulting solar cell characteristics strongly vary as a function of the bottom Mo layer deposition pressure. A bottom Mo layer growth at 2.93 Pa allows improving the solar cell conversion efficiency by 1.5 times compared to a bottom Mo layer deposited at 0.27 Pa. Using the improved Mo bilayer back contact, a maximum solar cell efficiency of 10.0% was obtained without sodium addition nor anti-reflection coating. - Highlights: • Mo bilayer back contacts for Cu(In,Ga)Se 2 solar cells were grown on Ti substrates. • The sputtering pressure of the bottom Mo layer was varied between 0.27 Pa and 4 Pa. • The top Mo layer controls the optical and electrical properties of the back contact. • The structure of the bottom Mo layer influences the morphology of the top Mo layer. • The back contact affects the CIGS texture, device series resistance and efficiency

Energy efficiency measures in China: A three-stage DEA analysis

Science.gov (United States)

Cai, Yu; Xiong, Siqin; Ma, Xiaoming

2017-04-01

This paper measures energy efficiency of 30 regions in China during 2010-2014 by using the three-stage data envelopment analysis (DEA) model. The results indict that environmental factors and random error both have significant impacts on energy efficiency. After eliminating these influences, the results present that the energy efficiency in developed regions is almost higher than that in undeveloped or resource-rich regions and low scale technical efficiency is the main constraining factor in inefficient regions. Based on the efficiency characteristics, this paper divides all regions into four types and provide differential energy strategies.

Stable isotope and geochronological study of the Mawchi Sn-W deposit, Myanmar : implications for timing of mineralization and ore genesis.

OpenAIRE

Myint, A.Z.; Yonezu, K.; Boyce, A.; Selby, D.; Scherstén, A.; Tindell, T.; Watanabe, K.; Swe, Y.

2018-01-01

Myanmar is endowed with abundant Sn-W mineralization, pre-eminent amongst which is the world-class Mawchi deposit. In the Mawchi area, N-S trending vertical or steeply dipping quartz veins are hosted by both Eocene granite and Carboniferous to Early Permian metasediments. Three stages of ore formation are recognized; (i) tourmaline-cassiterite stage (ii) main ore stage and (iii) sulfide stage. Tourmaline, cassiterite and pyrite-I are early-formed minerals and are representative of the first s...

Proteomic analysis of young leaves at three developmental stages in an albino tea cultivar

Directory of Open Access Journals (Sweden)

Li Juan

2011-08-01

Full Text Available Abstract Background White leaf No.1 is a typical albino tea cultivar grown in China and it has received increased attention in recent years due to the fact that white leaves containing a high level of amino acids, which are very important components affecting the quality of tea drink. According to the color of its leaves, the development of this tea cultivar is divided into three stages: the pre-albinistic stage, the albinistic stage and the regreening stage. To understand the intricate mechanism of periodic albinism, a comparative proteomic approach based on two-dimensional electrophoresis (2-DE and mass spectrometry was adopted first time to identify proteins that changed in abundance during the three developmental periods. Results The 2-DE results showed that the expression level of 61 protein spots varied markedly during the three developmental stages. To analyze the functions of the significantly differentially expressed protein spots, 30 spots were excised from gels and analyzed by matrix-assisted laser desorption ionization-time of flight-tandem mass spectrometry. Of these, 26 spots were successfully identified. All identified protein spots were involved in metabolism of carbon, nitrogen and sulfur, photosynthesis, protein processing, stress defense and RNA processing, indicating these physiological processes may play crucial roles in the periodic albinism. Quantitative real-time RT-PCR analysis was used to assess the transcriptional level of differentially expressed proteins. In addition, the ultrastructural studies revealed that the etioplast-chloroplast transition in the leaf cell of White leaf No. 1 was inhibited and the grana in the chloroplast was destroyed at the albinistic stage. Conclusions In this work, the proteomic analysis revealed that some proteins may have important roles in the molecular events involved in periodic albinism of White leaf No. 1 and identificated many attractive candidates for further investigation. In

Sulphur and lead isotopes in strata-bound deposits, ch. 8

International Nuclear Information System (INIS)

Sangster, D.F.

1976-01-01

The use of sulphur and lead isotopes as isotopic tracers in the study of ore deposits containing these elements is reviewed. A discussion of the general theory, including abundance and fractionation of sulphur isotopes, single-stage leads, and anomalous leads (two-stage) is given. Attention is paid to sulphur isotopes enclosed in deposits which are located in marine host rocks and in rocks of continental or near-continental origin, as well as in deposits of the conglomerate-U(-Au) type. The lead isotope content of volcanogenic massive sulphide deposits and carbonate-hosted lead-zinc deposits is discussed

Effects of Hot Streak and Phantom Cooling on Heat Transfer in a Cooled Turbine Stage Including Particulate Deposition

Energy Technology Data Exchange (ETDEWEB)

Bons, Jeffrey [The Ohio State Univ., Columbus, OH (United States); Ameri, Ali [The Ohio State Univ., Columbus, OH (United States)

2016-01-08

The objective of this research effort was to develop a validated computational modeling capability for the characterization of the effects of hot streaks and particulate deposition on the heat load of modern gas turbines. This was accomplished with a multi-faceted approach including analytical, experimental, and computational components. A 1-year no cost extension request was approved for this effort, so the total duration was 4 years. The research effort succeeded in its ultimate objective by leveraging extensive experimental deposition studies complemented by computational modeling. Experiments were conducted with hot streaks, vane cooling, and combinations of hot streaks with vane cooling. These studies contributed to a significant body of corporate knowledge of deposition, in combination with particle rebound and deposition studies funded by other agencies, to provide suitable conditions for the development of a new model. The model includes the following physical phenomena: elastic deformation, plastic deformation, adhesion, and shear removal. It also incorporates material property sensitivity to temperature and tangential-normal velocity rebound cross-dependencies observed in experiments. The model is well-suited for incorporation in CFD simulations of complex gas turbine flows due to its algebraic (explicit) formulation. This report contains model predictions compared to coefficient of restitution data available in the open literature as well as deposition results from two different high temperature turbine deposition facilities. While the model comparisons with experiments are in many cases promising, several key aspects of particle deposition remain elusive. The simple phenomenological nature of the model allows for parametric dependencies to be evaluated in a straightforward manner. This effort also included the first-ever full turbine stage deposition model published in the open literature. The simulations included hot streaks and simulated vane cooling

Understanding the Effect of Na in Improving the Performance of CuInSe₂ Based Photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Dobson, Kevin D. [Univ. of Delaware, Newark, DE (United States)

2015-11-17

Cu(In,Ga)Se₂ (CIGS) thin film photovoltaic technology is in the early stages of commercialization with an annual manufacturing capacity over 1 GW and has demonstrated the highest module efficiency of any of the thin film technologies. However there still is a lack of fundamental understanding of the relationship between the material properties and solar cell device operation. It is well known that the incorporation of a small amount of Na into the CIGS film during processing is essential for high efficiency devices. However, there are conflicting explanations for how Na behaves at the atomic scale. This report investigates how Na is incorporated into the CIGS device structure and evaluates the diffusion of Na into CIGS grain boundaries (GBs) and bulk crystallites. Participants: This project was carried out at the Institute of Energy Conversion at the University of Delaware, collaborating with the Rockett group at the University of Illinois Urbana-Champagne. Significant Findings: The significant outcomes of this project for each task include; Task 1.0: Effect of Na in Devices Fabricated on PVD Deposited CIGS; Na diffusion occurs through the Mo back contact via GBs driven by the presence of oxygen; Na reversibly compensates donor defects in CIGS GBs,Task 2.0: Na Incorporation in Single Crystal CIGS; and bulk Na diffusion proceeds rapidly such that grains are Na-saturated immediately following CIGS thin film manufacture. Industry Guidance: The presented results offer interesting concepts for modification of manufacturing processes of CIGS-based PV modules. Possible approaches to improve control of Na uptake and uniformly increase levels in CIGS films are highlighted for processes that employ either soda-lime glass or NaF as the Na source. Concepts include the potential of O₂ or oxidative based treatments of Mo back contacts to improve Na diffusion through the metal film and increase Na uptake into the growing CIGS. This project has also offered

Nitrogen removal and microbial communities in a three-stage system simulating a riparian environment.

Science.gov (United States)

Wang, Ziyuan; Wang, Zhixin; Pei, Yuansheng

2014-06-01

The riparian zone is an active interface for nitrogen removal, in which nitrogen transformations by microorganisms have not been valued. In this study, a three-stage system was constructed to simulate the riparian zone environments, and nitrogen removal as well as the microbial community was investigated in this 'engineered riparian system'. The results demonstrated that stage 1 of this system accounted for 41-51 % of total nitrogen removal. Initial ammonium loading and redox potential significantly impacted the nitrogen removal performances. Stages 1 and 2 were both composed of an anoxic/oxic (A/O) zone and an anaerobic column. The A/O zone removed most of the ammonium load (6.8 g/m(2)/day), while the anaerobic column showed a significant nitrate removal rate (11.1 g/m(2)/day). Molecular biological analysis demonstrated that bacterial diversity was high in the A/O zones, where ammonium-oxidizing bacteria and nitrite-oxidizing bacteria accounted for 8.42 and 3.32 % of the bacterial population, respectively. The denitrifying bacteria Acidovorax sp. and the nitrifying bacteria Nitrosospira/Nitrosomonas were the predominant microorganisms in this engineered riparian system. This three-stage system was established to achieve favorable nitrogen removal and the microbial community in the system was also retained. This investigation should deepen our understanding of biological nitrogen removal in engineered riparian zones.

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture next-generation thin film solar cells, development of technologies to manufacture CIS solar cell modules, development of technologies to increase high-quality film area; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu, CIS taiyo denchi module no seizo gijutsu kaihatsu, kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With an objective to improve efficiency and reduce cost of CIS-based thin film solar cells, research and development has been made on technologies to increase high-quality CIS film area and technologies to increase speed in the manufacturing process. This paper describes the achievements attained during fiscal 1997. The research covered development of technologies to form high-grade Cu (In, Ga) Se{sub 2} (CIGS) film by using the multi-dimensional deposition process, component technologies for forming a rear electrode, a buffer layer and a transparent electrode, and patterning technologies. As a result of the research, thickness of the CIGS film was reduced to half as much as that of the conventional films, having achieved conversion efficiency of 13.1%, which corresponds to about 90% of the conventional CIGS solar cells. In addition, elucidation was made on the effect of an MoSe{sub 2} layer existing on interface with CIGS/Mo in a CIGS solar cell imposed on solar cell characteristics. In developing an Mo film laser scribing technology, intensity dependence of laser energy was made clear, the energy being required for scribing according to surface condition of the Mo film. (NEDO)

Preliminary Response of Soil Fauna to Simulated N Deposition in Three Typical Subtropical Forests

Institute of Scientific and Technical Information of China (English)

XU Guo-Liang; MO Jiang-Ming; ZHOU Guo-Yi; FU Sheng-Lei

2006-01-01

A field-scale experiment arranged in a complete randomized block design with three N addition treatments including a control (no addition of N), a low N (5 g m-2 year-1), and a medium N (10 g m-2 year-1) was performed in each of the three typical forests, a pine (Pinus massoniana Lamb.) forest (PF), a pine-broadleaf mixed forest (MF) and a mature monsoon evergreen broadleaf forest (MEBF), of the Dinghushan Biosphere Reserve in subtropical China to study the response of soil fauna community to additions of N. Higher NH4+ and NO3- concentrations and a lower soil pH occurred in the medium N treatment of MEBF, whereas the NO3- concentration was the lowest in PF after the additions of N. The response of the density, group abundance and diversity index of soil fauna to addition of N varied with the forest type,and all these variables decreased with increasing N under MEBF but the trend was opposite under PF. The N treatments had no significant effects on these variables under MF. Compared with the control plots, the medium N treatment had significant negative effect on soil fauna under MEBF. The group abundance of soil fauna increased significantly with additions of higher N rates under PF. These results suggested that the response of soil fauna to N deposition varied with the forest type and N deposition rate, and soil N status is one of the important factors affecting the response of soil fauna to N deposition.

Effect of Simulated N Deposition on Soil Exchangeable Cations in Three Forest Types of Subtropical China

Institute of Scientific and Technical Information of China (English)

LU Xian-Kai; MO Jiang-Ming; P.GUNDERSERN; ZHU Wei-Xing; ZHOU Guo-Yi; LI De-Jun; ZHANG Xu

2009-01-01

The effects of simulated nitrogen (N) deposition on soil exchangeable cations were studied in three forest types of subtropical China.Four N treatments with three replications were designed for the monsoon evergreen broadleaf forest (mature forest):control (0 kg N ha-1 year-1),low N (50 kg N ha-1 year-1),medium N (100 kg N ha-1 year-1) and high N (150 kg N ha-1 ycar-1),and only three treatments (i.e.,control,low N,medium N) were established for the pine and mixed forests.Nitrogen had been applied continuously for 26 months before the measurement.The mature forest responded more rapidly and intensively to N additions than the pine and mixed forests,and exhibited some significant negative symptoms,e.g.,soil acidification,Al mobilization and leaching of base cations from soil.The pine and mixed forests responded slowly to N additions and exhibited no significant response of soil cations.Response of soil exchangeable cations to N deposition varied in the forests of subtropical China,depending on soil N status and land-nse history.

Observed degradation stages of ring-mold craters (RMC): Geomorphic evidence for modification of ice-rich deposits in the transitions zone between Elysium and Utopia Basin, Mars

DEFF Research Database (Denmark)

Pedersen, Gro Birkefeldt Møller

Deposits with pits, depressions and RMCs observed north of Elysium rise are interpreted as degraded mixtures of ice and clastic material (CCF, LVF and LDA). Degradation stages of RMCs are an important tool for mapping dusty, deflated ice-rich units....

The recent pumice eruptions of Mt. Pelée volcano, Martinique. Part I: Depositional sequences, description of pumiceous deposits

Science.gov (United States)

Traineau, Hervé; Westercamp, Denis; Bardintzeff, Jacques-Marie; Miskovsky, Jean-Claude

1989-08-01

Mount Pelée is one of the most active volcanoes of the Lesser Antilles arc, with more than twenty eruptions over the last 5000 years. Both nuée ardente-type eruptions, which are well known, and pumice eruptions, although little known, are very common in the stratigraphic record. The four younger pumice eruptions, P4 (2440 y.B.P.), P3 (2010 y.B.P.), P2 (1670 y.B.P.) and P1 (650 y.B.P.) can be used to reconstruct the eruption sequences. The various pumiceous deposits can be described as fine lithic ash layer, Plinian fall deposits, pumice and ash flow deposits with associated ash cloud fall deposits, and pumice surge deposits. Three kinds of depositional sequences have been defined. The distinctions between them are based on the occurrence of an initial Plinian phase and the generation of intraflow pyroclastic surges. The pumice eruptions of Mt. Pelée are small in intensity and magnitude, as expressed by the dispersal of their products and by the total mass of erupted material which is estimated to be less than 1 km 3 in each case. The pumice fall deposits have dispersal characteristics of small Plinian eruptions, close to the sub-Plinian type. Nevertheless, the probability of an occurrence of a new pumice eruption at Mt. Pelée is high, and the widespread distribution of pumice deposits around the volcano suggests that such an eruption is a major volcanic risk during the present stage of activity.

Photoelectrochemical water splitting using a Cu(In,Ga)Se{sub 2} thin film

Energy Technology Data Exchange (ETDEWEB)

Yokoyama, Daisuke; Minegishi, Tsutomu; Maeda, Kazuhiko; Katayama, Masao; Kubota, Jun; Domen, Kazunari [Department of Chemical System Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Yamada, Akira; Konagai, Makoto [Department of Physical Electronics, Graduate School of Engineering, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo 152-8550 (Japan)

2010-06-15

The effects of surface modification and reaction conditions on the photoelectrochemical properties of polycrystalline Cu(In,Ga)Se{sub 2} (CIGS) thin films for water splitting were studied. CIGS modified with platinum particles (Pt/CIGS) generated a cathodic photocurrent at potentials up to + 0.4 V vs. RHE at pH = 9.5. The photocurrent was stable for 16 h, which resulted in a turnover number of over 500. A CdS-inserted film (Pt/CdS/CIGS) had significantly improved properties compared to Pt/CIGS: a 0.3 V higher onset potential of cathodic photocurrent and a three-fold increase in the quantum efficiency. Our results suggest the feasibility of CIGS as a photocathode for biphotoelectrochemical water splitting. (author)

Shunt resistance and saturation current determination in CdTe and CIGS solar cells. Part 1: a new theoretical procedure and comparison with other methodologies

Science.gov (United States)

Rangel-Kuoppa, Victor-Tapio; Albor-Aguilera, María-de-Lourdes; Hérnandez-Vásquez, César; Flores-Márquez, José-Manuel; González-Trujillo, Miguel-Ángel; Contreras-Puente, Gerardo-Silverio

2018-04-01

A new proposal for the extraction of the shunt resistance (R sh ) and saturation current (I sat ) of a current-voltage (I-V) measurement of a solar cell, within the one-diode model, is given. First, the Cheung method is extended to obtain the series resistance (R s ), the ideality factor (n) and an upper limit for I sat . In this article which is Part 1 of two parts, two procedures are proposed to obtain fitting values for R sh and I sat within some voltage range. These two procedures are used in two simulated I-V curves (one in darkness and the other one under illumination) to recover the known solar cell parameters R sh , R s , n, I sat and the light current I lig and test its accuracy. The method is compared with two different common parameter extraction methods. These three procedures are used and compared in Part 2 in the I-V curves of CdS-CdTe and CIGS-CdS solar cells.

Mineralogy of the Chaparra IOCG deposit, southern Peru

Science.gov (United States)

Yáñez, Juan; Alfonso, Pura

2014-05-01

The Chaparra IOCG, located in southern Peru, near Chala, is mined and exploited by small-scale miners for gold, however, it has not been studied until now. Here we present a preliminary geological and mineralogic study of this deposit. Powder X ray diffraction, electron microscopy and electron microprobe were used to characterize the mineralization. This deposit is hosted in magmatic rocks from the Coastal Batholith. Host rocks belong to the Linga Super-unit, of Upper Cretaceous age and are mainly constituted by monzonites, monzogabbros and diorites. Major alterations are the propylitic (chlorite - albite - quartz), advanced argillic (jarosite - natrojarosite) and sericitic (muscovite-sericite-quartz). Gypsum and other alteration minerals such as potassium feldspar and phlogopite, vermiculite and natrolite are widespread. Mineralization occurs mainly in quartz veins up to 1 m thick, emplaced filling fractures. Ore mineralogy is mainly composed of hematite, goethite, and sulphides (mainly pyrite, chalcopyrite and covellite). Gold and REE-rich minerals also occur. Native gold can reach up to 1 mm in size, but usually is few μm in size. Its composition is 82-92 wt% Au, up to 12 wt% of Ag and Fe can reach up to 4 wt%. The paragenetic sequence in the Chaparra deposit was divided into three stages: (I) primary mineralization, (II) Fracture filling, and (III) supergene alteration. The sequence begins with the crystallization of magnetite, quartz, pyrrhotite and pyrite. Subsequently, native gold, native Bismuth and uraninite crystallices together with the former minerals, in which are enclosed. Later, monacite is formed, being enclosed in quartz. Pyrite also presents small grains of chalcopyrite inside. Galena, sphalerite and arsenopyrite also are formed, whether included in pyrite or outside. Scarce grains of sakuraiite also occur in this stage. Structural formula of sakuraiie from this deposit is Cu 01.78-1.90 Zn 0.07-12Fe 1.16-124In 0.22-0.26Sn 0.79-082S4). Indium

Identification of tsunami deposits considering the tsunami waveform: An example of subaqueous tsunami deposits in Holocene shallow bay on southern Boso Peninsula, Central Japan

Science.gov (United States)

Fujiwara, Osamu; Kamataki, Takanobu

2007-08-01

This study proposes a tsunami depositional model based on observations of emerged Holocene tsunami deposits in outcrops located in eastern Japan. The model is also applicable to the identification of other deposits, such as those laid down by storms. The tsunami deposits described were formed in a small bay of 10-20-m water depth, and are mainly composed of sand and gravel. They show various sedimentary structures, including hummocky cross-stratification (HCS) and inverse and normal grading. Although, individually, the sedimentary structures are similar to those commonly found in storm deposits, the combination of vertical stacking in the tsunami deposits makes a unique pattern. This vertical stacking of internal structures is due to the waveform of the source tsunamis, reflecting: 1) extremely long wavelengths and wave period, and 2) temporal changes of wave sizes from the beginning to end of the tsunamis. The tsunami deposits display many sub-layers with scoured and graded structures. Each sub-layer, especially in sandy facies, is characterized by HCS and inverse and normal grading that are the result of deposition from prolonged high-energy sediment flows. The vertical stack of sub-layers shows incremental deposition from the repeated sediment flows. Mud drapes cover the sub-layers and indicate the existence of flow-velocity stagnant stages between each sediment flow. Current reversals within the sub-layers indicate the repeated occurrence of the up- and return-flows. The tsunami deposits are vertically divided into four depositional units, Tna to Tnd in ascending order, reflecting the temporal change of wave sizes in the tsunami wave trains. Unit Tna is relatively fine-grained and indicative of small tsunami waves during the early stage of the tsunami. Unit Tnb is a protruding coarse-grained and thickest-stratified division and is the result of a relatively large wave group during the middle stage of the tsunami. Unit Tnc is a fine alternation of thin sand

Analysis of Three-dimension Viscous Flow in the Model Axial Compressor Stage K1002L

Science.gov (United States)

Tribunskaia, K.; Kozhukhov, Y. V.

2017-08-01

The main investigation subject considered in this paper is axial compressor model stage K1002L. Three simulation models were designed: Scheme 1 - inlet stage model consisting of IGV (Inlet Guide Vane), rotor and diffuser; Scheme 2 - two-stage model: IGV, first-stage rotor, first-stage diffuser, second-stage rotor, EGV (Exit Guide Vane); Scheme 3 - full-round model: IGV, rotor, diffuser. Numerical investigation of the model stage was held for four circumferential velocities at the outer diameter (Uout=125,160,180,210 m/s) within the range of flow coefficient: ϕ = 0.4 - 0.6. The computational domain was created with ANSYS CFX Workbench. According to simulation results, there were constructed aerodynamic characteristic curves of adiabatic efficiency and the adiabatic head coefficient calculated for total parameters were compared with data from the full-scale test received at the Central Boiler and Turbine Institution (CBTI), thus, verification of the calculated data was carried out. Moreover, there were conducted the following studies: comparison of aerodynamic characteristics of the schemes 1, 2; comparison of the sector and full-round models. The analysis and conclusions are supplemented by gas-dynamic method calculation for axial compressor stages.

Deposit3D: a tool for automating structure depositions to the Protein Data Bank

Energy Technology Data Exchange (ETDEWEB)

Badger, J., E-mail: jbadger@active-sight.com; Hendle, J.; Burley, S. K.; Kissinger, C. R. [SGX Inc., 10505 Roselle Street, San Diego, CA 92121 (United States)

2005-09-01

This paper describes a Python script that may be used to gather all required structure-annotation information into an mmCIF file for upload through the RCSB PDB ADIT structure-deposition interface. Almost all successful protein structure-determination projects in the public sector culminate in a structure deposition to the Protein Data Bank (PDB). In order to expedite the deposition proces, Deposit3D has been developed. This command-line script calculates or gathers all the required structure-deposition information and outputs this data into a mmCIF file for subsequent upload through the RCSB PDB ADIT interface. Deposit3D might be particularly useful for structural genomics pipeline projects because it allows workers involved with various stages of a structure-determination project to pool their different categories of annotation information before starting a deposition session.

Deposit3D: a tool for automating structure depositions to the Protein Data Bank

International Nuclear Information System (INIS)

Badger, J.; Hendle, J.; Burley, S. K.; Kissinger, C. R.

2005-01-01

This paper describes a Python script that may be used to gather all required structure-annotation information into an mmCIF file for upload through the RCSB PDB ADIT structure-deposition interface. Almost all successful protein structure-determination projects in the public sector culminate in a structure deposition to the Protein Data Bank (PDB). In order to expedite the deposition proces, Deposit3D has been developed. This command-line script calculates or gathers all the required structure-deposition information and outputs this data into a mmCIF file for subsequent upload through the RCSB PDB ADIT interface. Deposit3D might be particularly useful for structural genomics pipeline projects because it allows workers involved with various stages of a structure-determination project to pool their different categories of annotation information before starting a deposition session

Analysis on depositional system and discussion on ore-formation conditions of channel sandstone type uranium deposit. Taking Dongsheng area, Ordos meso-cenozoic basin as an example

International Nuclear Information System (INIS)

Wu Rengui; Yu Dagan; Zhu Minqiang; Zhou Wanpeng; Chen Anping

2003-01-01

Applying the theory of depositional system, the depositional facies and depositional systems of the Zhiluo Formation in Dongsheng area are systematically analysed, and the authors proposed that sediments of the Zhiluo Formation are of fluvial facies, and streams of the Zhiluo time experienced three evolution stages, namely: the early braided stream, the middle low sinuosity meandering stream and the late high sinuosity meandering stream. Based on features of paleoclimatic evolution, the Zhiluo Formation is divided into two lithological members. The lower lithological member consists of sediments of braided and low sinuosity meandering streams under humid-ward paleoclimatic conditions forming grey sedimentary formation. The upper member is composed of sediments of meandering streams under arid-hot paleoclimatic conditions representing complex-colored (mainly red) sedimentary formation. It is suggested that uranium mineralization in the study area is of channel sandstone type and controlled by braided channel sediments. Besides, the ore-formation conditions for channel sandstone type uranium deposit are preliminarily discussed

The three stages of epilepsy in patients with CDKL5 mutations.

Science.gov (United States)

Bahi-Buisson, Nadia; Kaminska, Anna; Boddaert, Nathalie; Rio, Marlène; Afenjar, Alexandra; Gérard, Marion; Giuliano, Fabienne; Motte, Jacques; Héron, Delphine; Morel, Marie Ange N'guyen; Plouin, Perrine; Richelme, Christian; des Portes, Vincent; Dulac, Olivier; Philippe, Christophe; Chiron, Catherine; Nabbout, Rima; Bienvenu, Thierry

2008-06-01

Mutations in the X-linked cyclin-dependent kinase-like 5 (CDKL5) gene are responsible for a severe encephalopathy with early epilepsy. So far, the electroclinical phenotype remains largely unknown and no clear genotype-phenotype correlations have been established. To characterize the epilepsy associated with CDKL5 mutations and to look for a relationship between the genotype and the course of epilepsy. We retrospectively analyzed the electroclinical phenotypes of 12 patients aged from 2.5 to 19 years diagnosed with pathogenic CDKL5 mutations and one patient with a novel intronic sequence variation of uncertain pathogenicity and examined whether the severity of the epilepsy was linked to the type and location of mutations. The epilepsy course reveals three successive stages: (Stage I) early epilepsy (onset 1-10 weeks) with normal interictal electroencephalogram (EEG) (10/13) despite frequent convulsive seizures; (Stage II) epileptic encephalopathy with infantile spasms (8/8) and hypsarrhythmia (8/8). At the age of evaluation, seven patients were seizure free and six had developed refractory epilepsy (stage III) with tonic seizures and myoclonia (5/6). Interestingly, the patients carrying a CDKL5 mutations causing a truncation of the catalytic domain tended to develop a more frequent refractory epilepsy than patients with mutations located downstream (4/6, 66.6% versus 1/6, 16%) although, these trends are not yet significant. Our data contribute to a better definition of the epileptic phenotype in CDKL5 mutations, and might give some clues to a potential relationship between the phenotype and the genotype in these patients.

Three dimensional modeling of depositional geometries. A case study from Tofane Group (Dolomites, Italy).

Science.gov (United States)

Gattolin, G.; Franceschi, M.; Breda, A.; Teza, G.; Preto, N.

2012-04-01

At the end of the Early Carnian, the Carnian Pluvial Event (CPE) resulted in a major crisis of carbonate factories. The sharp change in carbonate production lead to a dramatic modifications in depositional geometries. Steep clinoforms of the high-relief pre-crisis carbonate platforms were replaced by low-angle ramps. Spatial characters of depositional geometries can be decisive in identifying the genesis of geological bodies. We here show how 3D modeling techniques can be applied to help in quantifying and highlighting their variations. As case study we considered two outcrops in the Tofane Group (Dolomites, Italy). The first outcrop (bottom of southern walls of Tofana di Rozes) exposes a platform-to-basin transect of pre- and post-crisis platforms, the second (Dibona hut) a clinostratified carbonate body deposited during the Carnian crisis. Outcrop conditions at both sites, with vertical and hardly accessible walls, make the field tracing of depositional geometries particularly challenging. Line drawing on high resolution pictures can help (e.g. for clinoforms), but its use for quantification is hampered by perspective deformation. Three dimensional acquisition and modeling allow to retrieve the true spatial characters of sedimentary bodies in these outcrops. The geometry of the carbonate body at Dibona (~ 15000 sqm) was acquired with terrestrial LiDAR, while for Tofana photogrammetric techniques were applied because of the extension of the outcrop itself (~ 240000 sqm) and the lack of suitable points of view for terrestrial laser scanning. At Tofana, field observations reveal the presence of tens-hundreds m large carbonate mounds grown on a pre-existing inclined surface, intercalated with skeletal carbonates and siltites-arenites. This system rapidly evolves into a carbonate-clastic ramp. Photogrammetric topography acquisition permitted to place and visualize geological features in a three dimensional frame, thus obtaining a conceptual sedimentological model. A 3

Backoff-stage synchronization in three-hop string-topology wireless networks with hidden nodes

Science.gov (United States)

Sanada, Kosuke; Sekiya, Hiroo; Komuro, Nobuyoshi; Sakata, Shiro

In IEEE 802.11 wireless multi-hop networks, each node works individually and their individual operations generate entire network dynamics. It is important to clarify the network dynamics in wireless multi-hop networks for designing and constructing multi-hop communication networks. This paper presents the network-dynamics investigations for three-hop string-topology wireless network in detail. From the investigations, a “backoff-stage synchronization” phenomenon, which is mutuality between hidden nodes, is found. The mechanism of the backoff-stage synchronization is expressed and the sufficient conditions for the synchronization occurrence are given. This phenomenon gives some impacts on the IEEE 802.11 multi-hop-network communications.

Novel composite cBN-TiN coating deposition method: structure and performance in metal cutting

International Nuclear Information System (INIS)

Russell, W.C.; Malshe, A.P.; Yedave, S.N.; Brown, W.D.

2001-01-01

Cubic boron nitride coatings are under development for a variety of applications but stabilization of the pure cBN form and adhesion of films deposited by PVD and ion-based methods has been difficult. An alternative method for depositing a composite cBN-TiN film has been developed for wear related applications. The coating is deposited in a two-stage process utilizing ESC (electrostatic spray coating) and CVI (chemical vapor infiltration). Fully dense films of cBN particles evenly dispersed in a continuous TiN matrix have been developed. Testing in metal cutting has shown an increase in tool life (turning - 4340 steel) of three to seven times, depending of machining parameters, in comparison with CVD deposited TiN films. (author)

Atomic layer deposition of HfO{sub 2} for integration into three-dimensional metal-insulator-metal devices

Energy Technology Data Exchange (ETDEWEB)

Assaud, Loic [Aix Marseille Univ, CNRS, CINAM, Marseille (France); ICMMO-ERIEE, Universite Paris-Sud / Universite Paris-Saclay, CNRS, Orsay (France); Pitzschel, Kristina; Barr, Maissa K.S.; Petit, Matthieu; Hanbuecken, Margrit; Santinacci, Lionel [Aix Marseille Univ, CNRS, CINAM, Marseille (France); Monier, Guillaume [Universite Clermont Auvergne, Universite Blaise Pascal, CNRS, Institut Pascal, Clermont-Ferrand (France)

2017-12-15

HfO{sub 2} nanotubes have been fabricated via a template-assisted deposition process for further use in three-dimensional metal-insulator-metal (MIM) devices. HfO{sub 2} thin layers were grown by Atomic Layer Deposition (ALD) in anodic alumina membranes (AAM). The ALD was carried out using tetrakis(ethylmethylamino)hafnium and water as Hf and O sources, respectively. Long exposure durations to the precursors have been used to maximize the penetration depth of the HfO{sub 2} layer within the AAM and the effect of the process temperature was investigated. The morphology, the chemical composition, and the crystal structure were studied as a function of the deposition parameters using transmission and scanning electron microscopies, X-ray photoelectron spectroscopy, and X-ray diffraction, respectively. As expected, the HfO{sub 2} layers grown at low-temperature (T = 150 C) were amorphous, while for a higher temperature (T = 250 C), polycrystalline films were observed. The electrical characterizations have shown better insulating properties for the layers grown at low temperature. Finally, TiN/HfO{sub 2}/TiN multilayers were grown in an AAM as proof-of-concept for three-dimensional MIM nanostructures. (orig.)

Computerized breast cancer analysis system using three stage semi-supervised learning method.

Science.gov (United States)

Sun, Wenqing; Tseng, Tzu-Liang Bill; Zhang, Jianying; Qian, Wei

2016-10-01

A large number of labeled medical image data is usually a requirement to train a well-performed computer-aided detection (CAD) system. But the process of data labeling is time consuming, and potential ethical and logistical problems may also present complications. As a result, incorporating unlabeled data into CAD system can be a feasible way to combat these obstacles. In this study we developed a three stage semi-supervised learning (SSL) scheme that combines a small amount of labeled data and larger amount of unlabeled data. The scheme was modified on our existing CAD system using the following three stages: data weighing, feature selection, and newly proposed dividing co-training data labeling algorithm. Global density asymmetry features were incorporated to the feature pool to reduce the false positive rate. Area under the curve (AUC) and accuracy were computed using 10 fold cross validation method to evaluate the performance of our CAD system. The image dataset includes mammograms from 400 women who underwent routine screening examinations, and each pair contains either two cranio-caudal (CC) or two mediolateral-oblique (MLO) view mammograms from the right and the left breasts. From these mammograms 512 regions were extracted and used in this study, and among them 90 regions were treated as labeled while the rest were treated as unlabeled. Using our proposed scheme, the highest AUC observed in our research was 0.841, which included the 90 labeled data and all the unlabeled data. It was 7.4% higher than using labeled data only. With the increasing amount of labeled data, AUC difference between using mixed data and using labeled data only reached its peak when the amount of labeled data was around 60. This study demonstrated that our proposed three stage semi-supervised learning can improve the CAD performance by incorporating unlabeled data. Using unlabeled data is promising in computerized cancer research and may have a significant impact for future CAD system

Food intake, body reserves and reproductive success of barnacle geese Branta leucopsis staging in different habitats

NARCIS (Netherlands)

Prop, J; Black, JM; Mehlum, F; Black, JM; Madsen, J

1998-01-01

This paper concerns the effect of habitat choice on the dynamics of deposition of body reserves in spring-staging barnacle geese Branta leucopsis. On their way to breeding areas in Spitsbergen, these geese reside for several weeks on islands off the coast of Helgeland, Norway. They use three

Commercialization of High Efficiency Low Cost CIGS Technology Based on Electroplating: Final Technical Progress Report, 28 September 2007 - 30 June 2009

Energy Technology Data Exchange (ETDEWEB)

Basol, B.

2010-08-01

This report describes SoloPower's work as a Photovoltaic Technology Incubator awardee within the U.S. Department of Energy's Solar Energy Technologies Program. The term of this subcontract with the National Renewable Energy Laboratory was two years. The project focused on SoloPower's electrodeposition-based copper indium gallium (di)selenide (CIGS) technology. Under this subcontract, SoloPower improved the quality of its flexible metal substrates, increased the size of its solar cells from 0.5 cm2 to 120 cm2, increased the small-area cell efficiencies from near 11% to near 14%, demonstrated large-area cells, and developed a module manufacturing process.

Effectiveness of the Electronic Cigarette: An Eight-Week Flemish Study with Six-Month Follow-up on Smoking Reduction, Craving and Experienced Benefits and Complaints

Directory of Open Access Journals (Sweden)

Karolien Adriaens

2014-10-01

Full Text Available Background: Smoking reduction remains a pivotal issue in public health policy, but quit rates obtained with traditional quit-smoking therapies remain disappointingly low. Tobacco Harm Reduction (THR, aiming at less harmful ways of consuming nicotine, may provide a more effective alternative. One promising candidate for THR are electronic cigarettes (e-cigs. The aim of this study was to investigate the efficacy of second-generation e-cigs both in terms of acute craving-reduction in the lab and in terms of smoking reduction and experienced benefits/complaints in an eight-month Randomized Controlled Trial (RCT. Design: RCT with three arms. Methods: Participants (N = 48 unwilling to quit smoking were randomized into two e-cig groups and one control group. During three lab sessions (over two months participants, who had been abstinent for four hours, vaped/smoked for five minutes, after which we monitored the effect on craving and withdrawal symptoms. eCO and saliva cotinine levels were also measured. In between lab sessions, participants in the e-cig groups could use e-cigs or smoke ad libitum, whereas the control group could only smoke. After the lab sessions, the control group also received an e-cig. The RCT included several questionnaires, which repeatedly monitored the effect of ad libitum e-cig use on the use of tobacco cigarettes and the experienced benefits/complaints up to six months after the last lab session. Results: From the first lab session on, e-cig use after four hours of abstinence resulted in a reduction in cigarette craving which was of the same magnitude as when a cigarette was smoked, while eCO was unaffected. After two months, we observed that 34% of the e-cig groups had stopped smoking tobacco cigarettes, versus 0% of the control group (difference p < 0.01. After five months, the e-cig groups demonstrated a total quit-rate of 37%, whereas the control group showed a quit rate of 38% three months after initiating e-cig use. At

Insights into cadmium diffusion mechanisms in two-stage diffusion profiles in solar-grade Cu(In,Ga)Se{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Biderman, N. J.; Sundaramoorthy, R.; Haldar, Pradeep [Colleges of Nanoscale Science and Engineering, SUNY Polytechnic Institute, Albany, New York 12203 (United States); U.S. Photovoltaic Manufacturing Consortium, Albany, New York 12203 (United States); Novak, Steven W.; Lloyd, J. R. [Colleges of Nanoscale Science and Engineering, SUNY Polytechnic Institute, Albany, New York 12203 (United States)

2015-12-07

Cadmium diffusion experiments were performed on polished copper indium gallium diselenide (Cu(In,Ga)Se{sub 2} or CIGS) samples with resulting cadmium diffusion profiles measured by time-of-flight secondary ion mass spectroscopy. Experiments done in the annealing temperature range between 275 °C and 425 °C reveal two-stage cadmium diffusion profiles which may be indicative of multiple diffusion mechanisms. Each stage can be described by the standard solutions of Fick's second law. The slower cadmium diffusion in the first stage can be described by the Arrhenius equation D{sub 1} = 3 × 10{sup −4} exp (− 1.53 eV/k{sub B}T) cm{sup 2} s{sup −1}, possibly representing vacancy-meditated diffusion. The faster second-stage diffusion coefficients determined in these experiments match the previously reported cadmium diffusion Arrhenius equation of D{sub 2} = 4.8 × 10{sup −4} exp (−1.04 eV/k{sub B}T) cm{sup 2} s{sup −1}, suggesting an interstitial-based mechanism.

Quantifying aquatic insect deposition from lake to land.

Science.gov (United States)

Dreyer, Jamin; Townsend, Philip A; Hook, James C; Hoekman, David; Vander Zanden, M Jake; Gratton, Claudio

2015-02-01

Adjacent ecosystems are influenced by organisms that move across boundaries, such as insects with aquatic larval stages and terrestrial adult stages, which transport energy and nutrients from water to land. However, the ecosystem-level effect of aquatic insects on land has generally been ignored, perhaps because the organisms themselves are individually small. At the naturally productive Lake Mývatn, Iceland, we used two readily measured quantities: total insect emergence from water and relative insect density on land, to demonstrate an approach for estimating aquatic insect deposition (e.g., kg N x m(-2) x yr(-1)) to shore. Estimates from emergence traps between 2008 and 20.11 indicated a range of 0.15-3.7 g x m(-2) x yr(-1), or a whole-lake emergence of 3.1-76 Mg/yr; all masses are given as dry mass. Using aerial infall trap measurements of midge relative abundance over land, we developed a local-maximum decay function model to predict proportional midge deposition with distance from the lake. The dispersal model predicted midge abundance with R2 = 0.89, a pattern consistent among years, with peak midge deposition occurring 20-25 m inland and 70% of midges deposited within 100 m of shore. During a high-midge year (2008), we estimate midge deposition within the first 50 m of shoreline to be 100 kg xha(-1) x yr(-1), corresponding to inputs of 10 kg N x ha(-1) x yr(-1) and 1 kg P x ha(-1) x yr(-1), or about three to five times above background terrestrial N deposition rates. Consistent with elevated N input where midges are most dense, we observed that soil available nitrate in resin bags decreases with increasing distance from the lake. Our approach, generalizable to other systems, shows that aquatic insects can be a major source of nutrients to terrestrial ecosystems and have the capacity to significantly affect ecosystem processes.

Geological modeling of a stratified deposit with CAD-Based solid model automation

Directory of Open Access Journals (Sweden)

Ayten Eser

Full Text Available Abstract The planning stages of mining activities require many comprehensive and detailed analyses. Determining the correct orebody model is the first stage and one of the most important. Three-dimensional solid modeling is one of the significant methods that can examine the position and shape of the ore deposit. Although there are many different types of mining software for determining a solid model, many users try to build geological models in the computer without knowing how these software packages work. As researchers on the subject, we wanted to answer the question "How would we do it". For this purpose, a system was developed for generating solid models using data obtained from boreholes. Obtaining this model in an AutoCAD environment will be important for geologists and engineers. Developed programs were first tested with virtual borehole data belonging to a virtual deposit. Then the real borehole data of a cement raw material site were successfully applied. This article allows readers not only to see a clear example of the programming approach to layered deposits but also to produce more complicated software in this context. Our study serves as a window to understanding the geological modeling process.

Phanerozoic environments of black shale deposition and the Wilson Cycle

Directory of Open Access Journals (Sweden)

J. Trabucho-Alexandre

2012-02-01

Full Text Available The spatial and temporal distribution of black shales is related to the development of environments in which they accumulate and to a propitious combination of environmental variables. In recent years, much has been done to improve our understanding of the mechanisms behind the temporal distribution of black shales in the Phanerozoic and of the environmental variables that result in their deposition. However, the interpretation of ancient black shale depositional environments is dominated by an oversimplistic set of three depositional models that do not capture their complexity and dynamics. These three models, the restricted circulation, the (open ocean oxygen minimum and the continental shelf models, are an oversimplification of the variety of black shale depositional environments that arise and coexist throughout the course of a basin's Wilson Cycle, i.e. the dynamic sequence of events and stages that characterise the evolution of an ocean basin, from the opening continental rift to the closing orogeny. We examine the spatial distribution of black shales in the context of the Wilson Cycle using examples from the Phanerozoic. It is shown that the geographical distribution of environments of black shale deposition and the position of black shales in the basin infill sequence strongly depend on basin evolution, which controls the development of sedimentary environments where black shales may be deposited. The nature of the black shales that are deposited, i.e. lithology and type of organic matter, also depends on basin evolution and palaeogeography. We propose that in studies of black shales more attention should be given to the sedimentary processes that have led to their formation and to the interpretation of their sedimentary environments.

Optical characterization of In{sub 2}S{sub 3} solar cell buffer layers grown by chemical bath and physical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

Trigo, J.F.; Asenjo, B.; Herrero, J.; Gutierrez, M.T. [Department of Energy, CIEMAT, Avda. Complutense, 22, 28040 Madrid (Spain)

2008-09-15

In this paper, we study the optical properties of indium sulfide thin films to establish the best conditions to obtain a good solar cell buffer layer. The In{sub 2}S{sub 3} buffer layers have been prepared by chemical bath deposition (CBD) and thermal evaporation (PVD). Optical behavior differences have been found between CBD and PVD In{sub 2}S{sub 3} thin films that have been explained as due to structural, morphological and compositional differences observed in the films prepared by both methods. The resultant refractive index difference has to be attributed to the lower density of the CBD films, which can be related to the presence of oxygen. Its higher refractive index makes PVD film better suited to reduce overall reflectance in a typical CIGS solar cell. (author)

The Genesis of Precious and Base Metal Mineralization at the Miguel Auza Deposit, Zacatecas, Mexico

Science.gov (United States)

Findley, A. A.; Olivo, G. R.; Godin, L.

2009-05-01

The Miguel Auza mine located in Zacatecas State, Mexico, is a vein-type polymetallic epithermal deposit hosted in deformed argillite, siltstone and, greywacke of the Cretaceous Caracol Formation. Silver-rich base metal veins (0.2 m to >1.5 m wide) are spatially associated with the NE-striking, steeply SE- dipping (70-80°) Miguel Auza fault over a strike length of 1.6 km and a depth of 460 m. A 2 km2 monzonitic stock located in the proximity of the mineralized zones, has previously been interpreted as the source of the mineralizing fluids. Four distinct structural stages are correlated with hydrothermal mineral deposition: (I) The Pre-ore stage is characterized by normal faulting, fracturing of host rock, and rotation of bedding planes. This stage consists of quartz, illite, chlorite, +/- pyrite alteration of sedimentary wall rocks. (II) The Pyrite-vein stage is associated with reverse-sense reactivation of early normal faults, dilation of bedding planes/fractures, and deposition of generally barren calcite + pyrite veinlets. (III) The Main-ore stage is related to the development of reverse-fault- hosted massive sulphide veins. During this stage three phases of mineral deposition are recorded: early pyrite and arsenopyrite, intermediate chalcopyrite, pyrite, arsenopyrite, and base metals, and late base metals and Ag-bearing minerals. Associated gangue minerals during the main ore stage are quartz, muscovite, calcite and chlorite. (IV) The Post-ore stage involves late NW-SE striking block faulting, brecciation and calcite veining. Later supergene oxidation of veins led to deposition of Fe-oxides and hydroxides, commonly filling fractures or replacing early-formed sulphide assemblages. The various vein types display classic epithermal textures including open space filling, banding, comb quartz and brecciation. The Ag-bearing minerals comprise pyrargyrite [Ag3(Sb,As)S3], argentotennantite [(Cu,Ag)10(Zn,Fe)2(Sn,As)4S13], polybasite-pearceite [(Ag,Cu)16(Sb,As)2S11], and

Funcionamiento hidrológico de un humedal ribereño, el Masegar, en el conjunto de los humedales de La Mancha Húmeda de la cuenca alta del rió Cigüela

Directory of Open Access Journals (Sweden)

Llamas, M. R.

1995-12-01

Full Text Available Fifteen years ago «La Mancha Húmeda» was deelared Biosphere Reserve by UNESCO, at the request of the Spanish Government. According to a recent deelaration by UNESCO in 1995, such title could be lost if the degradation processes of the wetlands of «La Mancha Húmeda» continue. «La Mancha Húmeda» was formed by a hundred of small lakes or wetlands that in area totalled about 200-300 km2 and they were distributed over an area of about 25.000 km2. These are different types of wetlands (saltwater and freshwater, permanent and ephimeral, riparian and closed basins, etc.. It is estimated that the actual surface of all the wetlands is about 20-30% of that occupied 20 or 30 years ago. The most famous degradation case is that of the «Tablas de Daimiel National Park» that has shrinked fram an area of about 15-20km2 to less than 1 km2 This article presents the general situation of the riverine wetlands of the Cigüela river and the results of the hydrological functioning of a wetland of modest dimensions, less than 1 km2, El Masegar. It is a riparian wetland located in the Cigüela River basin which has been severely affected by man actions. El Masegar can be considered as an artificial wetland. From an ecological point of view, this wetland seems to have been functioning in a proper way until 1988, when the so called «Plan de Regeneración Hídrica del Parque Nacional de las Tablas de Daimiel» began. This Plan has not regenerated the Natural Park but has degradated or destroyed the riparian wetlands that existed along the Cigüela River valley which is about ISO km long. The surface of these wetlands all together was larger than that of Tablas de Daimiel National Park. The study shows that it could be feasible to restore or maintain most of the riparian wetlands of the «La Mancha Húmeda» without a great economic investment and without social conflicts with the farmers.En 1981, a petición del Gobierno español, la

Two stages and three components of the postural preparation to action.

Science.gov (United States)

Krishnan, Vennila; Aruin, Alexander S; Latash, Mark L

2011-07-01

Previous studies of postural preparation to action/perturbation have primarily focused on anticipatory postural adjustments (APAs), the changes in muscle activation levels resulting in the production of net forces and moments of force. We hypothesized that postural preparation to action consists of two stages: (1) Early postural adjustments (EPAs), seen a few hundred ms prior to an expected external perturbation and (2) APAs seen about 100 ms prior to the perturbation. We also hypothesized that each stage consists of three components, anticipatory synergy adjustments seen as changes in covariation of the magnitudes of commands to muscle groups (M-modes), changes in averaged across trials levels of muscle activation, and mechanical effects such as shifts of the center of pressure. Nine healthy participants were subjected to external perturbations created by a swinging pendulum while standing in a semi-squatting posture. Electrical activity of twelve trunk and leg muscles and displacements of the center of pressure were recorded and analyzed. Principal component analysis was used to identify four M-modes within the space of muscle activations using indices of integrated muscle activation. This analysis was performed twice, over two phases, 400-700 ms prior to the perturbation and over 200 ms just prior to the perturbation. Similar robust results were obtained using the data from both phases. An index of a multi-M-mode synergy stabilizing the center of pressure displacement was computed using the framework of the uncontrolled manifold hypothesis. The results showed high synergy indices during quiet stance. Each of the two stages started with a drop in the synergy index followed by a change in the averaged across trials activation levels in postural muscles. There was a very long electromechanical delay during the early postural adjustments and a much shorter delay during the APAs. Overall, the results support our main hypothesis on the two stages and three components

Archaean Gold Mineralization in an Extensional Setting: The Structural History of the Kukuluma and Matandani Deposits, Geita Greenstone Belt, Tanzania

Directory of Open Access Journals (Sweden)

Shimba D. Kwelwa

2018-04-01

Full Text Available Three major gold deposits, Matandani, Kukuluma, and Area 3, host several million ouncez (Moz of gold, along a ~5 km long, WNW trend in the E part of the Geita Greenstone Belt, NW Tanzania. The deposits are hosted in Archaean volcanoclastic sediment and intrusive diorite. The geological evolution of the deposits involved three separate stages: (1 an early stage of syn-sedimentary extensional deformation (D1 around 2715 Ma; (2 a second stage involving overprinting ductile folding (D2–4 and shearing (D5–6 events during N-S compression between 2700 and 2665 Ma, coeval with the emplacement of the Kukuluma Intrusive Complex; and (3 a final stage of extensional deformation (D7 accommodated by minor, broadly east-trending normal faults, preceded by the intrusion of felsic porphyritic dykes at ~2650 Ma. The geometry of the ore bodies at Kukuluma and Matandani is controlled by the distribution of magnetite-rich meta-ironstone, near the margins of monzonite-diorite bodies of the Kukuluma Intrusive Complex. The lithological contacts acted as redox boundaries, where high-grade mineralization was enhanced in damage zones with higher permeability, including syn-D3 hydrothermal breccia, D2–D3 fold hinges, and D6 shears. The actual mineralizing event was syn-D7, and occurred in an extensional setting that facilitated the infiltration of mineralizing fluids. Thus, whilst gold mineralization is late-tectonic, ore zone geometries are linked to older structures and lithological boundaries that formed before gold was introduced. The deformation-intrusive history of the Kukuluma and Matandani deposits is near identical to the geological history of the world-class Nyankanga and Geita Hill deposits in the central part of the Geita Greenstone Belt. This similarity suggests that the geological history of much of the greenstone belt is similar. All major gold deposits in the Geita Greenstone Belt lack close proximity to crustal-scale shear zones; they are associated

Three distinct Holocene intervals of stalagmite deposition and nondeposition revealed in NW Madagascar, and their paleoclimate implications

Science.gov (United States)

Riavo Gilbertinie Voarintsoa, Ny; Railsback, Loren Bruce; Brook, George Albert; Wang, Lixin; Kathayat, Gayatri; Cheng, Hai; Li, Xianglei; Edwards, Richard Lawrence; Rakotondrazafy, Amos Fety Michel; Olga Madison Razanatseheno, Marie

2017-12-01

Petrographic features, mineralogy, and stable isotopes from two stalagmites, ANJB-2 and MAJ-5, respectively from Anjohibe and Anjokipoty caves, allow distinction of three intervals of the Holocene in NW Madagascar. The Malagasy early Holocene (between ca. 9.8 and 7.8 ka) and late Holocene (after ca. 1.6 ka) intervals (MEHI and MLHI, respectively) record evidence of stalagmite deposition. The Malagasy middle Holocene interval (MMHI, between ca. 7.8 and 1.6 ka) is marked by a depositional hiatus of ca. 6500 years. Deposition of these stalagmites indicates that the two caves were sufficiently supplied with water to allow stalagmite formation. This suggests that the MEHI and MLHI intervals may have been comparatively wet in NW Madagascar. In contrast, the long-term depositional hiatus during the MMHI implies it was relatively drier than the MEHI and the MLHI. The alternating wet-dry-wet conditions during the Holocene may have been linked to the long-term migrations of the Intertropical Convergence Zone (ITCZ). When the ITCZ's mean position is farther south, NW Madagascar experiences wetter conditions, such as during the MEHI and MLHI, and when it moves north, NW Madagascar climate becomes drier, such as during the MMHI. A similar wet-dry-wet succession during the Holocene has been reported in neighboring locations, such as southeastern Africa. Beyond these three subdivisions, the records also suggest wet conditions around the cold 8.2 ka event, suggesting a causal relationship. However, additional Southern Hemisphere high-resolution data will be needed to confirm this.

The Evolution of Language in Three Stages

Directory of Open Access Journals (Sweden)

Michael Corballis

2007-06-01

Full Text Available Syntactic language is a uniquely human accomplishment, and must therefore have evolved since the split of the hominins from the other great apes some six million years ago. I argue that there were three main phases. The first came about through the emergence of bipedalism, a distinctively hominin trait, which enhanced the capacity for manual communication by freeing the hands and opening a frontal stance. The second began with the emergence of the larger-brained genus Homo from around 2 million years ago. The increase in brain size may have been driven by the necessity for enhanced social cooperation, and the emergence of a more effective system for communicating propositional information. Many of the properties of language, including the use of arbitrary symbols, and the emergence of tense and other markers of time and place, may have been driven by the increased understanding of time, and the advantages gained by recording and communicating episodic events. In short, language acquired syntax. The final stage, unique to Homo sapiens, was the emergence of autonomous speech as the primary mode of communication, replacing earlier dependence on manual gesture. This may help explain the dominance of our species over other hominin species, and indeed over the planet

Copper variation in Cu(In,Ga)Se{sub 2} solar cells with indium sulphide buffer layer

Energy Technology Data Exchange (ETDEWEB)

Spiering, S., E-mail: stefanie.spiering@zsw-bw.de [Zentrum für Sonnenenergie- und Wasserstoff-Forschung (ZSW) Baden-Wuerttemberg, Industriestrasse 6, 70565 Stuttgart (Germany); Paetel, S.; Kessler, F. [Zentrum für Sonnenenergie- und Wasserstoff-Forschung (ZSW) Baden-Wuerttemberg, Industriestrasse 6, 70565 Stuttgart (Germany); Igalson, M.; Abdel Maksoud, H. [Warsaw University of Technology (WUT), Faculty of Physics, Koszykowa 75, 00-662 Warszawa (Poland)

2015-05-01

In the manufacturing of Cu(In,Ga)Se{sub 2} (CIGS) thin film solar cells the application of a buffer layer on top of the absorber is essential to obtain high efficiency devices. Regarding the roll-to-roll production of CIGS cells and modules a vacuum deposition process for the buffer is preferable to the conventional cadmium sulphide buffer deposited in a chemical bath. Promising results have already been achieved for the deposition of indium sulphide buffer by different vacuum techniques. The solar device performance is very sensitive to the conditions at the absorber-buffer heterojunction. In view of optimization we investigated the influence of the Cu content in the absorber on the current-voltage characteristics. In this work the integral copper content was varied between 19 and 23 at.% in CIGS on glass substrates. An improvement of the cell performance by enhanced open circuit voltage was observed for a reduction to ~ 21 at.% when thermally evaporated indium sulphide was applied as the buffer layer. The influence of stoichiometry deviations on the transport mechanism and secondary barriers in the device was studied using detailed dark and light current-voltage analysis and admittance spectroscopy and compared to the reference CdS-buffered cells. We conclude that the composition of the absorber in the interface region affects current transport in In{sub x}S{sub y}-buffered and CdS-buffered cells in different ways hence optimal Cu content in those two types of devices is different. - Highlights: • Influence of Cu-variation in CIGS cells with In{sub x}S{sub y} buffer layer on cell performance • Enhanced efficiency by slight reduction of Cu-content to 21 at.% • Contribution of tunnelling-enhanced interface recombination for higher Cu-content.

Preparation and Characterization of Molybdenum Thin Film to Photovoltaic applications; Preparacion y Caracterizacion de Peliculas Delgadas de Molibdeno para Aplicaciones Fotovoltaicas

Energy Technology Data Exchange (ETDEWEB)

Andres, M.; Gutierrez, M. T.

2007-09-18

Molybdenum (Mo) is one of the main material used as back ohmic contact for Cu(In,Ga)Se2 (CIGS) thin film solar cells. It has to provide the electrical properties of low resistivity electrode and high reflectance in the absorbance region of CIGS layer. Also, it has to have high thermal stability, an adequate morphology and good adhesion to the substrate. The aim of this work has been the preparation of Mo layers onto two types of substrates, soda-lime glass (SLG) and a commercial flexible polyimide called Kapton, and the evaluation as a flexible substrate in CIGS solar cells. Internal stress, adhesion, microstructure and optical and electrical properties of Mo thin films have been studied as a function of deposition parameters (gas pressure, power density and time). The change of the substrate from rigid one to flexible introduces tensile stress due to the difference in the coefficient of thermal expansion (CTE) between the coating and the substrate. Low stress in Mo/Kapton structure has been obtained; this is a good result to use in CIGS flexible solar cells. (Author) 23 refs.

Progress in Polycrystalline Thin-Film Cu(In,GaSe2 Solar Cells

Directory of Open Access Journals (Sweden)

Udai P. Singh

2010-01-01

Full Text Available For some time, the chalcopyrite semiconductor CuInSe2 and its alloy with Ga and/or S [Cu(InGaSe2 or Cu(InGa(Se,S2], commonly referred as CIGS, have been leading thin-film material candidates for incorporation in high-efficiency photovoltaic devices. CuInSe2-based solar cells have shown long-term stability and the highest conversion efficiencies among all thin-film solar cells, reaching 20%. A variety of methods have been reported to prepare CIGS thin film. Efficiency of solar cells depends upon the various deposition methods as they control optoelectronic properties of the layers and interfaces. CIGS thin film grown on glass or flexible (metal foil, polyimide substrates require p-type absorber layers of optimum optoelectronic properties and n-type wideband gap partner layers to form the p-n junction. Transparent conducting oxide and specific metal layers are used for front and back contacts. Progress made in the field of CIGS solar cell in recent years has been reviewed.

Raman scattering analysis of Cu-poor Cu(In,Ga)Se{sub 2} cells fabricated on polyimide substrates: Effect of Na content on microstructure and phase structure

Energy Technology Data Exchange (ETDEWEB)

Izquierdo-Roca, V. [IN2UB/Departament d' Electronica, Universitat de Barcelona, C. Marti i Franques 1, 08028, Barcelona (Spain); Caballero, R. [Helmholtz Zentrum Berlin fuer Materialien und Energie, Hahn-Meitner Platz 1, 14109, Berlin (Germany); Fontane, X. [IREC, Catalonia Institute for Energy Research, C. Josep Pla 2 B2, 08019, Barcelona (Spain); Kaufmann, C.A. [Helmholtz Zentrum Berlin fuer Materialien und Energie, Hahn-Meitner Platz 1, 14109, Berlin (Germany); Alvarez-Garcia, J. [Centre de Recerca i Investigacio de Catalunya (CRIC), Trav. de Gracia 108, 08012 Barcelona (Spain); Calvo-Barrio, L. [Lab. Analisis de Superficies, SCT, Universitat de Barcelona, Lluis Sole i Sabaris 1-3, 08028 Barcelona (Spain); Saucedo, E. [IREC, Catalonia Institute for Energy Research, C. Josep Pla 2 B2, 08019, Barcelona (Spain); Perez-Rodriguez, A., E-mail: aperezr@irec.cat [IN2UB/Departament d' Electronica, Universitat de Barcelona, C. Marti i Franques 1, 08028, Barcelona (Spain); IREC, Catalonia Institute for Energy Research, C. Josep Pla 2 B2, 08019, Barcelona (Spain); Morante, J.R. [INUB/Departament d' Electronica, Universitat de Barcelona, C. Marti i Franques 1, 08028, Barcelona (Spain); IREC, Catalonia Institute for Energy Research, C. Josep Pla 2 B2, 08019, Barcelona (Spain); Schock, H.W. [Helmholtz Zentrum Berlin fuer Materialien und Energie, Hahn-Meitner Platz 1, 14109, Berlin (Germany)

2011-08-31

This work reports the Raman scattering surface and in-depth resolved analysis of Cu-poor Cu(In,Ga)Se{sub 2} (CIGS) grown on polyimide substrates. In order to study the effect of Na on the formation and microstructure of the CIGS and the corresponding Cu-poor ordered vacancy compound (OVC) phases, a NaF precursor layer with different thicknesses was deposited on the Mo-coated substrates before growing of the samples. The Raman spectroscopy data are correlated with the analysis of the samples by Auger electron spectroscopy and scanning electron microscopy. These data corroborate the significant role of Na on the inhibition of Ga-In interdiffusion and on the formation of the MoSe{sub 2} interfacial phase at the back region of the layers. Presence of Na also leads to an enhancement in the formation of the chalcopyrite CIGS phase and a decrease in the occurrence of the dominant OVC phase at the surface region. This study confirms the strong dependence of the microstructure and phase distribution in CIGS absorber layers on the Na available during their growth.

Multipathing Via Three Parameter Common Image Gathers (CIGs) From Reverse Time Migration

Science.gov (United States)

Ostadhassan, M.; Zhang, X.

2015-12-01

A noteworthy problem for seismic exploration is effects of multipathing (both wanted or unwanted) caused by subsurface complex structures. We show that reverse time migration (RTM) combined with a unified, systematic three parameter framework that flexibly handles multipathing can be accomplished by adding one more dimension (image time) to the angle domain common image gather (ADCIG) data. RTM is widely used to generate prestack depth migration images. When using the cross-correlation image condition in 2D prestack migration in RTM, the usual practice is to sum over all the migration time steps. Thus all possible wave types and paths automatically contribute to the resulting image, including destructive wave interferences, phase shifts, and other distortions. One reason is that multipath (prismatic wave) contributions are not properly sorted and mapped in the ADCIGs. Also, multipath arrivals usually have different instantaneous attributes (amplitude, phase and frequency), and if not separated, the amplitudes and phases in the final prestack image will not stack coherently across sources. A prismatic path satisfies an image time for it's unique path; Cavalca and Lailly (2005) show that RTM images with multipaths can provide more complete target information in complex geology, as multipaths usually have different incident angles and amplitudes compared to primary reflections. If the image time slices within a cross-correlation common-source migration are saved for each image time, this three-parameter (incident angle, depth, image time) volume can be post-processed to generate separate, or composite, images of any desired subset of the migrated data. Images can by displayed for primary contributions, any combination of primary and multipath contributions (with or without artifacts), or various projections, including the conventional ADCIG (angle vs depth) plane. Examples show that signal from the true structure can be separated from artifacts caused by multiple

What makes us think? A three-stage dual-process model of analytic engagement.

Science.gov (United States)

Pennycook, Gordon; Fugelsang, Jonathan A; Koehler, Derek J

2015-08-01

The distinction between intuitive and analytic thinking is common in psychology. However, while often being quite clear on the characteristics of the two processes ('Type 1' processes are fast, autonomous, intuitive, etc. and 'Type 2' processes are slow, deliberative, analytic, etc.), dual-process theorists have been heavily criticized for being unclear on the factors that determine when an individual will think analytically or rely on their intuition. We address this issue by introducing a three-stage model that elucidates the bottom-up factors that cause individuals to engage Type 2 processing. According to the model, multiple Type 1 processes may be cued by a stimulus (Stage 1), leading to the potential for conflict detection (Stage 2). If successful, conflict detection leads to Type 2 processing (Stage 3), which may take the form of rationalization (i.e., the Type 1 output is verified post hoc) or decoupling (i.e., the Type 1 output is falsified). We tested key aspects of the model using a novel base-rate task where stereotypes and base-rate probabilities cued the same (non-conflict problems) or different (conflict problems) responses about group membership. Our results support two key predictions derived from the model: (1) conflict detection and decoupling are dissociable sources of Type 2 processing and (2) conflict detection sometimes fails. We argue that considering the potential stages of reasoning allows us to distinguish early (conflict detection) and late (decoupling) sources of analytic thought. Errors may occur at both stages and, as a consequence, bias arises from both conflict monitoring and decoupling failures. Copyright © 2015 Elsevier Inc. All rights reserved.

Electron accelerator-based production of molybdenum-99: Bremsstrahlung and photoneutron generation from molybdenum vs. tungsten

Energy Technology Data Exchange (ETDEWEB)

Tsechanski, A. [Ben-Gurion University of the Negev, Department of Nuclear Engineering, P.O. Box 653, Beer-Sheva 84105 (Israel); Bielajew, A.F. [Department of Nuclear Engineering and Radiological Sciences, The University of Michigan, 2355 Bonisteel Boulevard, Ann Arbor, MI 48109 (United States); Archambault, J.P.; Mainegra-Hing, E. [National Research Council of Canada, Ionizing Radiation Standards Laboratory, Ottawa, ON K1A 0R6 (Canada)

2016-01-01

for the one-stage approach of three enriched {sup 100}Mo-targets of a 2 cm diameter and thicknesses of 1, 2, and 3 radiation lengths (RL) were calculated to be: 19.54 Ci/g, 23.05 Ci/g, and 21.23 Ci/g, respectively. These results were compared with the evaluation presented in by Diamond et al. [19] for the same diameter and thickness {sup 100}Mo-targets in a two-stage approach. The comparison demonstrates that for all thicknesses under consideration, the specific activities at equilibrium in the one-stage approach are substantially greater than those evaluated in Diamond et al. [19] for the two-stage approach. More specifically, the specific activities at equilibrium in the Mo converter/target approach are greater than those in the standard W converter/Mo target approach at {sup 100}Mo target thicknesses of 1RL, 2RL, and 3RL by 28.9%, 82.5%, and 80.1%, respectively.

Local electrophoresis deposition assisted by laser trapping coupled with a spatial light modulator for three-dimensional microfabrication

Science.gov (United States)

Matsuura, Toshiki; Takai, Takanari; Iwata, Futoshi

2017-10-01

We describe a novel three-dimensional fabrication technique using local electrophoresis deposition assisted by laser trapping coupled with a spatial light modulator (SLM). In a solution containing nanometer-scale colloidal Au particles, multiple laser spots formed on a conductive substrate by the SLM gathered the nanoparticles together, and then the nanoparticles were electrophoretically deposited onto the substrate by an applied electrical field. However, undesirable sub-spots often appeared due to optical interference from the multiple laser spots, which deteriorated the accuracy of the deposition. To avoid the appearance of undesirable sub-spots, we proposed a method using quasi-multiple spots, which we realized by switching the position of a single spot briefly using the SLM. The method allowed us to deposit multiple dots on the substrate without undesirable sub-dot deposition. By moving the substrate downward during deposition, multiple micro-pillar structures could be fabricated. As a fabrication property, the dependence of the pillar diameter on laser intensity was investigated by changing the number of laser spots. The smallest diameter of the four pillars fabricated in this study was 920 nm at the laser intensity of 2.5 mW. To demonstrate the effectiveness of the method, multiple spiral structures were fabricated. Quadruple spirals of 46 µm in height were successfully fabricated with a growth rate of 0.21 µm/s using 2200 frames of the CGH patterns displayed in the SLM at a frame rate of 10 fps.

Evaporative Optical Marangoni Assembly: Tailoring the Three-Dimensional Morphology of Individual Deposits of Nanoparticles from Sessile Drops.

Science.gov (United States)

Anyfantakis, Manos; Varanakkottu, Subramanyan Namboodiri; Rudiuk, Sergii; Morel, Mathieu; Baigl, Damien

2017-10-25

We have recently devised the evaporative optical Marangoni assembly (eOMA), a novel and versatile interfacial flow-based method for directing the deposition of colloidal nanoparticles (NPs) on solid substrates from evaporating sessile drops along desired patterns using shaped UV light. Here, we focus on a fixed UV spot irradiation resulting in a cylinder-like deposit of assembled particles and show how the geometrical features of the single deposit can be tailored in three dimensions by simply adjusting the optical conditions or the sample composition, in a quantitative and reproducible manner. Sessile drops containing cationic NPs and a photosensitive surfactant at various concentrations are allowed to evaporate under a single UV beam with a diameter much smaller than that of the drop. After complete evaporation, the geometrical characteristics of the NP deposits are precisely assessed using optical profilometry. We show that both the volume and the radial size of the light-directed NP deposit can be adjusted by varying the diameter or the intensity of the UV beam or alternatively by changing the concentration of the photosensitive surfactant. Notably, in all these cases, the deposits display an almost constant median height corresponding to a few layers of particles. Moreover, both the radial and the axial extent of the patterns are tuned by changing the NP concentration. These results are explained by the correlation among the strength of Marangoni flow, the particle trapping efficiency, and the volume of the deposit, and by the role of evaporation-driven flow in strongly controlling the deposit height. Finally, we extend the versatility of eOMA by demonstrating that NPs down to 30 nm in diameter can be effectively patterned on glass or polymeric substrates.

Enhanced coproduction of hydrogen and methane from cornstalks by a three-stage anaerobic fermentation process integrated with alkaline hydrolysis.

Science.gov (United States)

Cheng, Xi-Yu; Liu, Chun-Zhao

2012-01-01

A three-stage anaerobic fermentation process including H(2) fermentation I, H(2) fermentation II, methane fermentation was developed for the coproduction of hydrogen and methane from cornstalks. Hydrogen production from cornstalks using direct microbial conversion by Clostridium thermocellum 7072 was markedly enhanced in the two-stage thermophilic hydrogen fermentation process integrated with alkaline treatment. The highest total hydrogen yield from cornstalks in the two-stage fermentation process reached 74.4 mL/g-cornstalk. The hydrogen fermentation effluents and alkaline hydrolyzate were further used for methane fermentation by anaerobic granular sludge, and the total methane yield reached 205.8 mL/g-cornstalk. The total energy recovery in the three-stage anaerobic fermentation process integrated with alkaline hydrolysis reached 70.0%. Copyright © 2011 Elsevier Ltd. All rights reserved.

The genesis of the newly discovered giant Wuben magmatic Fe-Ti oxide deposit in the Emeishan Large Igneous Province: a product of the late-stage redistribution and sorting of crystal slurries

Science.gov (United States)

Bai, Zhong-Jie; Zhong, Hong; Zhu, Wei-Guang; Hu, Wen-Jun; Chen, Cai-Jie

2018-04-01

A giant Fe-Ti oxide deposit hosted by the Wuben mafic intrusion has recently been discovered in the Pan-Xi area of the Emeishan Large Igneous Province (ELIP). The evolved compositions of the gangue minerals within the Fe-Ti oxide ores indicate that they formed during later stages of magma differentiation than those within the neighboring Panzhihua intrusion or other ore-bearing intrusions in this area. The rocks from the Wuben intrusion and MZb of the Panzhihua intrusion contain compositionally similar silicate minerals and have similar titanomagnetite/ilmenite ratios, suggesting that the former is related to and probably connected to the latter by subsurface magmatic conduits. This indicates that unconsolidated minerals that formed in the MZb flowed as crystal slurries into the Wuben magma chamber during the later stages of evolution of the parental magma. The later secondary enrichment of Fe-Ti oxides by mechanical redistribution and the sorting of crystals as a result of density and size differences generated the Wuben massive Fe-Ti oxide bodies. The ilmenite was commonly saturated in the magma at late stage of differentiation in the ELIP, thereby the associated deposit contains much higher contents of ilmenite. This indicates that future exploration for Fe-Ti oxide mineralization in the ELIP should not merely focus on the lower parts of large layered intrusions but should also include nearby relatively small intrusions or even the upper parts of large intrusions, especially as ilmenite-enriched Fe-Ti oxide deposits may have greater economic value than ilmenite-poor deposits.

Injection of a microsatellite in circular orbits using a three-stage launch vehicle

Science.gov (United States)

Marchi, L. O.; Murcia, J. O.; Prado, A. F. B. A.; Solórzano, C. R. H.

2017-10-01

The injection of a satellite into orbit is usually done by a multi-stage launch vehicle. Nowadays, the space market demonstrates a strong tendency towards the use of smaller satellites, because the miniaturization of the systems improve the cost/benefit of a mission. A study to evaluate the capacity of the Brazilian Microsatellite Launch Vehicle (VLM) to inject payloads into Low Earth Orbits is presented in this paper. All launches are selected to be made to the east side of the Alcântara Launch Center (CLA). The dynamical model to calculate the trajectory consists of the three degrees of freedom (3DOF) associated with the translational movement of the rocket. Several simulations are performed according to a set of restrictions imposed to the flight. The altitude reached in the separation of the second stage, the altitude and velocity of injection, the flight path angle at the moment of the activation of the third stage and the duration of the ballistic flight are presented as a function of the payload carried.

Odor and VOC Emissions from Pan Frying of Mackerel at Three Stages: Raw, Well-Done, and Charred

Directory of Open Access Journals (Sweden)

Jeong-Hyeon Ahn

2014-11-01

Full Text Available Many classes of odorants and volatile organic compounds that are deleterious to our wellbeing can be emitted from diverse cooking activities. Once emitted, they can persist in our living space for varying durations. In this study, various volatile organic compounds released prior to and during the pan frying of fish (mackerel were analyzed at three different cooking stages (stage 1 = raw (R, stage 2 = well-done (W, and stage 3 = overcooked/charred (O. Generally, most volatile organic compounds recorded their highest concentration levels at stage 3 (O, e.g., 465 (trimethylamine and 106 ppb (acetic acid. In contrast, at stage 2 (W, the lowest volatile organic compounds emissions were observed. The overall results of this study confirm that trimethylamine is identified as the strongest odorous compound, especially prior to cooking (stage 1 (R and during overcooking leading to charring (stage 3 (O. As there is a paucity of research effort to measure odor intensities from pan frying of mackerel, this study will provide valuable information regarding the management of indoor air quality.

Accounting of 131l decomposition under retrospective assessment of its deposition on the basis of determination of 129l deposition

Directory of Open Access Journals (Sweden)

Gavrilin Yu.l.

2013-12-01

given article aimed a justification of approaches to account of radioactive decay of 131l in the course of determination of its ground deposition density on the basis of determination of the ground deposition density of 129l at the late stage after the accident.

A three-dimensional methodology for the assessment of neutron damage and nuclear energy deposition in graphite components of advanced gas-cooled reactors

Energy Technology Data Exchange (ETDEWEB)

Morgan, D.O.; Robinson, A.T.; Allen, D.A.; Picton, D.J.; Thornton, D.A. [TCS, Serco, Rutherford House, Olympus Park, Quedgeley, Gloucester, Gloucestershire GL2 4NF (United Kingdom); Shaw, S.E. [EDF Energy, Barnet Way, Barnwood, Gloucester GL4 3RS (United Kingdom)

2011-07-01

This paper describes the development of a three-dimensional methodology for the assessment of neutron damage and nuclear energy deposition (or nuclear heating) throughout the graphite cores of the UK's Advanced Gas-cooled Reactors. Advances in the development of the Monte Carlo radiation transport code MCBEND have enabled the efficient production of detailed fully three-dimensional models that utilise three-dimensional source distributions obtained from Core Follow data supplied by the reactor physics code PANTHER. The calculational approach can be simplified to reduce both the requisite number of intensive radiation transport calculations, as well as the quantity of data output. These simplifications have been qualified by comparison with explicit calculations and they have been shown not to introduce significant systematic uncertainties. Simple calculational approaches are described that allow users of the data to address the effects on neutron damage and nuclear energy deposition predictions of the feedback resulting from the mutual dependencies of graphite weight loss and nuclear energy deposition. (authors)

76 FR 41392 - Interest on Deposits; Deposit Insurance Coverage

Science.gov (United States)

2011-07-14

... banks' funding costs and also allow them to plan business growth more dependably and rigorously... of business deposits by offering continually higher rates of interest. Three of the four contended... deposits. They reasoned that large banks will offer high rates of interest and lure away business...

Experimental measurements of the thermal conductivity of ash deposits: Part 2. Effects of sintering and deposit microstructure

Energy Technology Data Exchange (ETDEWEB)

A. L. Robinson; S. G. Buckley; N. Yang; L. L. Baxter

2000-04-01

The authors report results from an experimental study that examines the influence of sintering and microstructure on ash deposit thermal conductivity. The measurements are made using a technique developed to make in situ, time-resolved measurements of the effective thermal conductivity of ash deposits formed under conditions that closely replicate those found in the convective pass of a commercial boiler. The technique is designed to minimize the disturbance of the natural deposit microstructure. The initial stages of sintering and densification are accompanied by an increase in deposit thermal conductivity. Subsequent sintering continues to densify the deposit, but has little effect on deposit thermal conductivity. SEM analyses indicates that sintering creates a layered deposit structure with a relatively unsintered innermost layer. They hypothesize that this unsintered layer largely determines the overall deposit thermal conductivity. A theoretical model that treats a deposit as a two-layered material predicts the observed trends in thermal conductivity.

Design and modelling of an innovative three-stage thermal storage system for direct steam generation CSP plants

Science.gov (United States)

Garcia, Pierre; Vuillerme, Valéry; Olcese, Marco; El Mourchid, Nadim

2016-05-01

Thermal Energy Storage systems (TES) for a Direct Steam Generation (DSG) solar plant feature preferably three stages in series including a latent heat storage module so that steam can be recovered with a limited temperature loss. The storage system designed within the Alsolen Sup project is characterized by an innovative combination of sensible and latent modules. A dynamic model of this three-stage storage has been developed and applied to size the storage system of the Alsolen Sup® plant demonstrator at CEA Cadarache. Results of this simulation show that this promising concept is an efficient way to store heat in DSG solar plants.

Optical thin film deposition

International Nuclear Information System (INIS)

Macleod, H.A.

1979-01-01

The potential usefulness in the production of optical thin-film coatings of some of the processes for thin film deposition which can be classified under the heading of ion-assisted techniques is examined. Thermal evaporation is the process which is virtually universally used for this purpose and which has been developed to a stage where performance is in almost all respects high. Areas where further improvements would be of value, and the possibility that ion-assisted deposition might lead to such improvements, are discussed. (author)

Aerodynamic and Performance Behavior of a Three-Stage High Efficiency Turbine at Design and Off-Design Operating Points

Directory of Open Access Journals (Sweden)

M. T. Schobeiri

2004-01-01

Full Text Available This article deals with the aerodynamic and performance behavior of a three-stage high pressure research turbine with 3-D curved blades at its design and off-design operating points. The research turbine configuration incorporates six rows beginning with a stator row. Interstage aerodynamic measurements were performed at three stations, namely downstream of the first rotor row, the second stator row, and the second rotor row. Interstage radial and circumferential traversing presented a detailed flow picture of the middle stage. Performance measurements were carried out within a rotational speed range of 75% to 116% of the design speed. The experimental investigations have been carried out on the recently established multi-stage turbine research facility at the Turbomachinery Performance and Flow Research Laboratory, TPFL, of Texas A&M University.

Influence of encapsulated electron active molecules of single walled-carbon nanotubes on superstrate-type Cu(In,Ga)Se{sub 2} solar cells

Energy Technology Data Exchange (ETDEWEB)

Lee, Jungwoo [Department of Chemistry, Hanyang University, Seoul 133-791 (Korea, Republic of); CRD Laboratory, LG Chem. Research Park, Daejeon 305-738 (Korea, Republic of); Lee, Wonjoo [Department of Defense Ammunitions, Daeduk College, Daejeon 305-715 (Korea, Republic of); Shrestha, Nabeen K.; Lee, Deok Yeon; Lim, Iseul [Department of Chemistry, Hanyang University, Seoul 133-791 (Korea, Republic of); Kang, Soon Hyung [Department of Chemistry Education, Chonnam National University, Gwangju 500-757 (Korea, Republic of); Nah, Yoon-Chae [School of Energy, Materials, and Chemical Engineering, Korea University of Technology and Education, Cheonan 330-708 (Korea, Republic of); Lee, Soo-Hyoung, E-mail: shlee66@jbnu.ac.kr [School of Semiconductor and Chemical Engineering, Chonbuk National University, Jeonju 561-756 (Korea, Republic of); Yi, Whikun, E-mail: wkyi@hanyang.ac.kr [Department of Chemistry, Hanyang University, Seoul 133-791 (Korea, Republic of); Han, Sung-Hwan, E-mail: shhan@hanyang.ac.kr [Department of Chemistry, Hanyang University, Seoul 133-791 (Korea, Republic of)

2014-03-01

Chemical functionalization of carbon nanotubes (CNTs) can strongly affect the efficiency of solar cells due to change of three factors viz. electronic energy structures, interfacial resistance, and electrical field. Therefore, it is worthwhile to investigate the influence of these three factors on the solar cells based on the functionalization of various active molecules in CNTs. In the present study, we investigate the influence of the three factors in the efficiency of superstrate-type Cu(In,Ga)Se{sub 2} (CIGS) solar cells [i.e. F-doped SnO{sub 2}/CNTs/CdS/CIGS/Au] by encapsulation of electron withdrawing and donating organic molecules inside CNTs. The CIGS solar cell was characterized using the electronic diagram, electrochemical impendence spectroscopy, reverse field emission currents, and currents–voltages curves. - Highlights: • We investigated the three effects of CNTs in superstrate-type CIGS solar cells. • Chemical functionalization of CNTs strongly affect the efficiency of solar cells. • The electrical field of solar cell was characterized using the reverse FE-currents.

Trends of deposition fluxes and loadings of sulfur dioxide and nitrogen oxides in the artificial Three Northern Regions Shelter Forest across northern China

International Nuclear Information System (INIS)

Zhang, Xiaodong; Huang, Tao; Zhang, Leiming; Gao, Hong; Shen, Yanjie; Ma, Jianmin

2015-01-01

This study provides the first estimate of dry deposition fluxes of criteria air pollutants (SO_2 and NO_x) across the Three Northern Regions Shelter Forest (TNRSF) region in Northern China and their long-term trends from 1982 to 2010 using the inferential method. Dry deposition velocities of SO_2 and NO_x increased in many places of the TNRSF up to 118.2% for SO_2 and 112.1% for NO_x over the last three decades due to the increased vegetation coverage over the TNRSF. The highest atmospheric deposition fluxes of SO_2 and NO_x were found in the Central-North China region, followed by the Northeast and the Northwest China regions of the TNRSF. A total of 820,000 t SO_2 and 218,000 t NO_x was estimated to be removed from the atmosphere through dry deposition process over the TNRSF from 1982 to 2010. About 50% of the total removal occurred in the Central-North China region. The estimated total SO_2 and NO_x dry deposition fluxes from 1982 to 2010 between a TNRSF site in this region and an adjacent farmland outside the TNRSF showed that the fluxes of these two chemicals at the TNRSF site were the factors of 2–3 greater than their fluxes in the farmland. - Highlights: • We investigate removal of air pollutants by the Three-North Shelter Forest (Green Great Wall) in China. • The trend of SO_2 and NO_x dry deposition velocity and flux over the TNRSF increase over the last three decades. • Increasing trends of deposition fluxes of SO_2 and NO_x are more evident in Central-North and Northeast China. • We show higher deposition fluxes of SO_2 and NO_x within the TNSF than outside TNRSF. • Stronger removal of air pollutants by the TNRSF is expected when other criteria air pollutants are taken into account. - The TNRSF is demonstrated to be an effective sink for SO_2 and NO_x and has increased the removal of air pollutants from Northern China.

CANOPY STRUCTURE AND DEPOSITION EFFICIENCY OF VINEYARD SPRAYERS

Directory of Open Access Journals (Sweden)

Gianfranco Pergher

2007-06-01

Full Text Available A field study was performed to analyse how deposition efficiency from an axial-fan sprayer was affected by the canopy structure of vines trained to the High Cordon, Low Cordon and Casarsa systems, at beginning of flowering and beginning of berry touch growth stages. An empirical calibration method, providing a dose rate adjustment roughly proportional to canopy height, was used. The canopy structure was assessed using the Point Quadrat method, and determining the leaf area index (LAI and the leaf layer index (LLI. Spray deposits were measured by colorimetry, using a water soluble dye (Tartrazine as a tracer. Correlation between deposits and canopy parameters were analysed and discussed. Foliar deposits per unit leaf area were relatively constant, suggesting that empirical calibration can reduce deposit variability associated with different training systems and growth stages. Total foliar deposition ranged from 33.6% and 82.3% of total spray volume, and increased proportionally with the LLI up to LLI<4. Deposits on bunches significantly decreased with the LLI in the grape zone. The results suggest that sprayer efficiency is improved by a regular, symmetrical canopy, with few leaf layers in the grape zone as in Low Cordon. However, a LLI<3 over the whole canopy and >40% gaps in the foliage both reduced total deposition, and may increase the risk for larger drift losses.

In situ thermal imaging and three-dimensional finite element modeling of tungsten carbide-cobalt during laser deposition

International Nuclear Information System (INIS)

Xiong Yuhong; Hofmeister, William H.; Cheng Zhao; Smugeresky, John E.; Lavernia, Enrique J.; Schoenung, Julie M.

2009-01-01

Laser deposition is being used for the fabrication of net shapes from a broad range of materials, including tungsten carbide-cobalt (WC-Co) cermets (composites composed of a metallic phase and a hard refractory phase). During deposition, an unusual thermal condition is created for cermets, resulting in rather complex microstructures. To provide a fundamental insight into the evolution of such microstructures, we studied the thermal behavior of WC-Co cermets during laser deposition involving complementary results from in situ high-speed thermal imaging and three-dimensional finite element modeling. The former allowed for the characterization of temperature gradients and cooling rates in the vicinity of the molten pool, whereas the latter allowed for simulation of the entire sample. By combining the two methods, a more robust analysis of the thermal behavior was achieved. The model and the imaging results correlate well with each other and with the alternating sublayers observed in the microstructure.

Alunite in the Pascua-Lama high-sulfidation deposit: Constraints on alteration and ore deposition using stable isotope geochemistry

Science.gov (United States)

Deyell, C.L.; Leonardson, R.; Rye, R.O.; Thompson, J.F.H.; Bissig, T.; Cooke, D.R.

2005-01-01

The Pascua-Lama high-sulfidation system, located in the El Indio-Pascua belt of Chile and Argentina, contains over 16 million ounces (Moz) Au and 585 Moz Ag. The deposit is hosted primarily in granite rocks of Triassic age with mineralization occurring in several discrete Miocene-age phreatomagmatic breccias and related fracture networks. The largest of these areas is Brecha Central, which is dominated by a mineralizing assemblage of alunite-pyrite-enargite and precious metals. Several stages of hydrothermal alteration related to mineralization are recognized, including all types of alunite-bearing advanced argillic assemblages (magmatic-hydrothermal, steam-heated, magmatic steam, and supergene). The occurrence of alunite throughout the paragenesis of this epithermal system is unusual and detailed radiometric, mineralogical, and stable isotope studies provide constraints on the timing and nature of alteration and mineralization of the alunite-pyiite-enargite assemblage in the deposit. Early (preore) alteration occurred prior to ca. 9 Ma and consists of intense silicic and advanced argillic assemblages with peripheral argillic and widespread propylitic zones. Alunite of this stage occurs as fine intergrowths of alunite-quartz ?? kaolinite, dickite, and pyrophyllite that selectively replaced feldspars in the host rock. Stable isotope systematics suggest a magmatic-hydrothermal origin with a dominantly magmatic fluid source. Alunite is coeval with the main stage of Au-Ag-Cu mineralization (alunite-pyrite-enargite assemblage ore), which has been dated at approximately 8.8 Ma. Ore-stage alunite has an isotopic signature similar to preore alunite, and ?? 34Salun-py data indicate depositional temperatures of 245?? to 305??C. The ??D and ?? 18O data exclude significant involvement of meteoric water during mineralization and indicate that the assemblage formed from H2S-dominated magmatic fluids. Thick steam-heated alteration zones are preserved at the highest elevations in

Three-stage entry game: The strategic effects of advertising

Directory of Open Access Journals (Sweden)

Kuzmanović Marija

2011-01-01

Full Text Available This paper analyzes the effects of investment in advertising in the three-stage entry game model with one incumbent and one potential entrant firm. It is shown that if a game theory is applied, under particular conditions, advertising can be used as a strategic weapon in the market entry game. Depending on the level of the advertising interaction factor, conditions for over-investment in advertising for strategic purposes are given. Furthermore, three specific cases are analyzed: strictly predatory advertising, informative advertising and the case when one firm’s advertising cannot directly influence the other firm's profit. For each of them, depending on the costs of advertising and marginal costs, equilibrium is determined, and conditions under which it is possible to deter the entry are given. It is shown that if the value of the advertising interaction factor increases, power of using advertising as a weapon to deter entry into the market decreases. Thus, in the case of informative advertising, advertising cannot be used as a tool for deterring entry into the market, while in the case of predatory advertising, it can. Also, we have proved that in the case of strictly informative advertising an over-investment never occurs, while in the two other cases, there is always over-investment either to deter or to accommodate the entry.

Single-stage three-phase AC to DC conversion with isolation and Bi-directional power flow

NARCIS (Netherlands)

Vermulst, B.J.D.; Duarte, J.L.; Wijnands, C.G.E.; Lomonova, E.A.

2014-01-01

An approach for three-phase AC to DC conversion is proposed, which consists of a single-stage while offering galvanic isolation, soft-switching, bi-directional power flow and a significant reduction of inductive and capacitive energy storage. Two elements enable this approach, namely a neutral

Degradation analysis of thin film photovoltaic modules

International Nuclear Information System (INIS)

Radue, C.; Dyk, E.E. van

2009-01-01

Five thin film photovoltaic modules were deployed outdoors under open circuit conditions after a thorough indoor evaluation. Two technology types were investigated: amorphous silicon (a-Si:H) and copper indium gallium diselenide (CIGS). Two 14 W a-Si:H modules, labelled Si-1 and Si-2, were investigated. Both exhibited degradation, initially due to the well-known light-induced degradation described by Staebler and Wronski [Applied Physics Letters 31 (4) (1977) 292], and thereafter due to other degradation modes such as cell degradation. The various degradation modes contributing to the degradation of the a-Si:H modules will be discussed. The initial maximum power output (P MAX ) of Si-1 was 9.92 W, with the initial light-induced degradation for Si-1 ∼30% and a total degradation of ∼42%. For Si-2 the initial P MAX was 7.93 W, with initial light-induced degradation of ∼10% and a total degradation of ∼17%. Three CIGS modules were investigated: two 20 W modules labelled CIGS-1 and CIGS-2, and a 40 W module labelled CIGS-3. CIGS-2 exhibited stable performance while CIGS-1 and CIGS-3 exhibited degradation. CIGS is known to be stable over long periods of time, and thus the possible reasons for the degradation of the two modules are discussed.

Degradation analysis of thin film photovoltaic modules

Energy Technology Data Exchange (ETDEWEB)

Radue, C., E-mail: chantelle.radue@nmmu.ac.z [Department of Physics, PO Box 77000, Nelson Mandela Metropolitan University, Port Elizabeth 6031 (South Africa); Dyk, E.E. van [Department of Physics, PO Box 77000, Nelson Mandela Metropolitan University, Port Elizabeth 6031 (South Africa)

2009-12-01

Five thin film photovoltaic modules were deployed outdoors under open circuit conditions after a thorough indoor evaluation. Two technology types were investigated: amorphous silicon (a-Si:H) and copper indium gallium diselenide (CIGS). Two 14 W a-Si:H modules, labelled Si-1 and Si-2, were investigated. Both exhibited degradation, initially due to the well-known light-induced degradation described by Staebler and Wronski [Applied Physics Letters 31 (4) (1977) 292], and thereafter due to other degradation modes such as cell degradation. The various degradation modes contributing to the degradation of the a-Si:H modules will be discussed. The initial maximum power output (P{sub MAX}) of Si-1 was 9.92 W, with the initial light-induced degradation for Si-1 approx30% and a total degradation of approx42%. For Si-2 the initial P{sub MAX} was 7.93 W, with initial light-induced degradation of approx10% and a total degradation of approx17%. Three CIGS modules were investigated: two 20 W modules labelled CIGS-1 and CIGS-2, and a 40 W module labelled CIGS-3. CIGS-2 exhibited stable performance while CIGS-1 and CIGS-3 exhibited degradation. CIGS is known to be stable over long periods of time, and thus the possible reasons for the degradation of the two modules are discussed.

A Palaeoproterozoic multi-stage hydrothermal alteration system at Nalunaq gold deposit, South Greenland

DEFF Research Database (Denmark)

Bell, Robin-Marie; Kolb, Jochen; Waight, Tod Earle

2017-01-01

Nalunaq is an orogenic, high gold grade deposit situated on the Nanortalik Peninsula, South Greenland. Mineralisation is hosted in shear zone-controlled quartz veins, located in fine- and medium-grained amphibolite. The deposit was the site of Greenland’s only operating metalliferous mine until i...

Experience of development of porphyry copper type deposits in the Urals

Directory of Open Access Journals (Sweden)

И. А. Алтушкин

2017-12-01

Full Text Available Russian copper company was the first in Russia to start developing porphyry copper deposits. In 2013 the Mikheevsky mining and processing plant with the annual production capacity of 18 mln t of ore was put into exploitation. The use of innovative approaches regarding choice of the technology, high-performance equipment and organization of construction allowed to bring the enterprise to a full capacity and to achieve expected results within three years. On the basis of the experience obtained during design, construction and exploitation of the Mikheevsky mining and processing plant in 2017 the company has started the construction of a new mining and processing plant in the Tominskoye deposit. The first stage anticipates the enterprise production capacity to be equal to 28 mln t with the possibility of its increase up to 56 mln t. The development of porphyry copper deposits in the Urals will allow to provide copper plants with the raw materials over the next 80-100 years.

Fluid Inclusion and Oxygen Isotope Constraints on the Origin and Hydrothermal Evolution of the Haisugou Porphyry Mo Deposit in the Northern Xilamulun District, NE China

Directory of Open Access Journals (Sweden)

Qihai Shu

2017-01-01

Full Text Available The Haisugou porphyry Mo deposit is located in the northern Xilamulun district, northeastern China. Based on alteration and mineralization styles and crosscutting relationships, the hydrothermal evolution in Haisugou can be divided into three stages: an early potassic alteration stage with no significant metal deposition, a synmineralization sericite-chlorite alteration stage with extensive Mo precipitation, and a postmineralization stage characterized by barren quartz and minor calcite and fluorite. The coexistence of high-salinity brine inclusions with low-salinity inclusions both in potassic alteration stage (~440°C and locally in the early time of mineralization stage (380–320°C indicates the occurrence of fluid boiling. The positive correlations between the homogenization temperatures and the salinities of the fluids and the low oxygen isotopic compositions (δ18Ofluid < 3‰ of the syn- to postmineralization quartz together suggest the mixing of magmatic fluids with meteoric water, which dominated the whole mineralization process. The early boiling fluids were not responsible for ore precipitation, whereas the mixing with meteoric water, which resulted in temperature decrease and dilution that significantly reduced the metal solubility, should have played the major role in Mo mineralization. Combined fluid inclusion microthermometry and chlorite geothermometer results reveal that ore deposition mainly occurred between 350 and 290°C in Haisugou.

Reproductive isolation in hybrid mice due to spermatogenesis defects at three meiotic stages.

Science.gov (United States)

Oka, Ayako; Mita, Akihiko; Takada, Yuki; Koseki, Haruhiko; Shiroishi, Toshihiko

2010-09-01

Early in the process of speciation, reproductive failures occur in hybrid animals between genetically diverged populations. The sterile hybrid animals are often males in mammals and they exhibit spermatogenic disruptions, resulting in decreased number and/or malformation of mature sperms. Despite the generality of this phenomenon, comparative study of phenotypes in hybrid males from various crosses has not been done, and therefore the comprehensive genetic basis of the disruption is still elusive. In this study, we characterized the spermatogenic phenotype especially during meiosis in four different cases of reproductive isolation: B6-ChrX(MSM), PGN-ChrX(MSM), (B6 × Mus musculus musculus-NJL/Ms) F(1), and (B6 × Mus spretus) F(1). The first two are consomic strains, both bearing the X chromosome of M. m. molossinus; in B6-ChrX(MSM), the genetic background is the laboratory strain C57BL/6J (predominantly M. m. domesticus), while in PGN-ChrX(MSM) the background is the PGN2/Ms strain purely derived from wild M. m. domesticus. The last two cases are F(1) hybrids between mouse subspecies or species. Each of the hybrid males exhibited cell-cycle arrest and/or apoptosis at either one or two of three distinct meiotic stages: premeiotic stage, zygotene-to-pachytene stage of prophase I, and metaphase I. This study shows that the sterility in hybrid males is caused by spermatogenic disruptions at multiple stages, suggesting that the responsible genes function in different cellular processes. Furthermore, the stages with disruptions are not correlated with the genetic distance between the respective parental strains.

Optical constants of Cu(In, Ga)Se{sub 2} for arbitrary Cu and Ga compositions

Energy Technology Data Exchange (ETDEWEB)

Minoura, Shota; Kodera, Keita; Nakane, Akihiro; Fujiwara, Hiroyuki, E-mail: fujiwara@gifu-u.ac.jp [Center of Innovative Photovoltaic Systems (CIPS), Gifu University, 1-1 Yanagido, Gifu 501-1193 (Japan); Maekawa, Takuji [Research and Development Headquarters, ROHM Co., Ltd., 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585 (Japan); Niki, Shigeru [Research Center for Photovoltaic Technologies, National Institute of Advanced Industrial Science and Technology (AIST), Central2, 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568 (Japan)

2015-05-21

The optical constants of Cu(In, Ga)Se{sub 2} (CIGS)-based polycrystalline layers with different Cu and Ga compositions are parameterized completely up to a photon energy of 6.5 eV assuming several Tauc-Lorentz transition peaks. Based on the modeled optical constants, we establish the calculation procedure for the CIGS optical constants in a two-dimensional compositional space of (Cu, Ga) by taking the composition-induced shift of the critical point energies into account. In particular, we find that the variation of the CIGS optical constants with the Cu composition can be modeled quite simply by a spectral-averaging method in which the dielectric function of the target Cu composition is estimated as a weighted average of the dielectric functions with higher and lower Cu compositions. To express the effect of the Ga composition, on the other hand, an energy shift model reported earlier is adopted. Our model is appropriate for a wide variety of CIGS-based materials having different Cu and Ga compositions, although the modeling error increases slightly at lower Cu compositions [Cu/(In + Ga) < 0.69]. From our model, the dielectric function, refractive index, extinction coefficient, and absorption coefficient for the arbitrary CIGS composition can readily be obtained. The optical database developed in this study is applied further for spectroscopic ellipsometry analyses of CIGS layers fabricated by single and multi-stage coevaporation processes. We demonstrate that the compositional and structural characterizations of the CIGS-based layers can be performed from established analysis methods.

Rubidium distribution at atomic scale in high efficient Cu(In,Ga)Se2 thin-film solar cells

Science.gov (United States)

Vilalta-Clemente, Arantxa; Raghuwanshi, Mohit; Duguay, Sébastien; Castro, Celia; Cadel, Emmanuel; Pareige, Philippe; Jackson, Philip; Wuerz, Roland; Hariskos, Dimitrios; Witte, Wolfram

2018-03-01

The introduction of a rubidium fluoride post deposition treatment (RbF-PDT) for Cu(In,Ga)Se2 (CIGS) absorber layers has led to a record efficiency up to 22.6% for thin-film solar cell technology. In the present work, high efficiency CIGS samples with RbF-PDT have been investigated by atom probe tomography (APT) to reveal the atomic distribution of all alkali elements present in CIGS layers and compared with non-treated samples. A Scanning Electron Microscopy Dual beam station (Focused Ion Beam-Gas Injection System) as well as Transmission Kikuchi diffraction is used for atom probe sample preparation and localization of the grain boundaries (GBs) in the area of interest. The analysis of the 3D atomic scale APT reconstructions of CIGS samples with RbF-PDT shows that inside grains, Rb is under the detection limit, but the Na concentration is enhanced as compared to the reference sample without Rb. At the GBs, a high concentration of Rb reaching 1.5 at. % was found, and Na and K (diffusing from the glass substrate) are also segregated at GBs but at lower concentrations as compared to Rb. The intentional introduction of Rb leads to significant changes in the chemical composition of CIGS matrix and at GBs, which might contribute to improve device efficiency.

[Smoking fewer cigarettes per day may determine a significant risk reduction in developing smoking attributable diseases? Is there a risk reduction for e-cigarette users?].

Science.gov (United States)

Pieri, Luca; Chellini, Elisabetta; Gorini, Giuseppe

2014-01-01

Among Italian smokers--about 10 millions in 2013--about 600,000 began using electronic cigarettes (e-cigs) in last years. About 10% of e-cig users quitted smoking tobacco, whereas the 90% was dual users. Among them, about three out of four decreased the number of cigarettes smoked per day (cig/day), but did not quit. How many fewer cigarettes a smoker has to smoke to obtain significant health benefits? Is there a threshold? In order to observe a significant 27% reduction in the risk of developing lung cancer, a smoker must reduce the number of cig/day by at least 50%, while for the other smoking-related diseases (acute myocardial infarction - AMI, stroke, chronic obstructive pulmonary diseases), halving the number of cig/day did not drive to a significant risk reduction. Even smoking 5 cig/day increases the risk of AMI, whereas it significantly lowers the risk of lung cancer. Obviously, quitting smoking is the best choice to highly reduce risks for all smoking-related diseases. Therefore, in order to achieve significant risk reductions, e-cig users should quit smoking as first choice, or, if they feel it is impossible to them, reduce the consumption of traditional cigarettes to less than 5 cig/day.

57Fe NGR studies on three-stage hydroliquefaction of coals

International Nuclear Information System (INIS)

Jamond, M.; Bacaud, R.; Bussiere, P.; Charcosset, H.; Nickel-Pepin-Donat, B.

1990-01-01

Iron Moessbauer spectroscopy has been performed on liquefaction residues of two different French coals. In a three-stage liquefaction of high volatile bituminous coal (Freyming), without an added catalyst, the coal pyrite is not entirely converted into pyrrhotites, whereas in the presence of an added catalyst, coal pyrite is totally transformed into more dispersed pyrrhotites than those from the sample without an added catalyst; furthermore, the whole added catalyst precursor is reduced into pyrrhotites. In the case of liquefaction of subbituminous coal (Gardanne), full conversion of coal pyrite into pyrrhotites (even without an added catalyst) occurs. In addition, in the presence of the added catalyst, besides pyrrhotites, FeS is evidenced. When molybdenum-iron oxide is added as a catalyst precursor, no mixed Fe-Mo phase is detected. (orig.)

Deposits formed by ascending vein water (3 type)

International Nuclear Information System (INIS)

Komarova, G.V.

1980-01-01

Deposits formed by ascending vein waters (3 type), are considered using uranium-bitumen deposit in red-coloured continental sediments of Permo-Triassic as an example. Geological-structural and hydrogeological conditions of mineralization localization and conditions of deposit formation are discussed. Mineralogic-geochemical features and morphology of ore bodies are characterized. Attention is paid to the problem of epigenetic zone in ore-containing rocks and stages of its formation [ru

Geology and ore fluid geochemistry of the Jinduicheng porphyry molybdenum deposit, East Qinling, China

Science.gov (United States)

Li, Hongying; Ye, Huishou; Wang, Xiaoxia; Yang, Lei; Wang, Xiuyuan

2014-01-01

Jinduicheng deposit is a giant Mesozoic porphyry Mo system deposit in the East Qinling molybdenum belt, Shaanxi Province, China. The mineralization is associated with the I-type Jinduicheng granite porphyry. Both the porphyry stock and country rocks underwent intense hydrothermal alteration. The alteration, with increasing distance from the parent intrusion, changes from silicification, through potassic and phyllic assemblages, carbonation, to propylitic assemblages. Molybdenite, the dominant ore mineral, occurs in veinlets, most of which are hosted by the altered country rocks, with less than 25% of the ore in the porphyry body. The hydrothermal system comprises four stages, including pre-ore quartz and K-feldspar; two ore stages of quartz, K-feldspar, molybdenite, and Pb- And Zn-bearing sulfides; and post-ore quartz and carbonate. Six main types of primary fluid inclusions are present in hydrothermal quartz, including two-phase aqueous, one-phase aqueous, three-phase CO2-bearing, CO2-dominated fluid inclusions, gas inclusions, and melt inclusions. The homogenization temperatures of fluid inclusions range from 210 to 290 °C in the pre-ore stage, 150-310 °C in ore stage I, 150-360 °C in the ore stage II, and 195-325 °C in the post-ore stage quartz. Estimated salinities of the ore-forming fluids range from 6.9 to 13.5, 4.3 to 12.3, 6.2 to 12.4, and 3.4 to 9.9 wt.% NaCl equiv. in stages 1-4, respectively. The δ34S values of pyrite in the two ore stages range from 2.8‰ to 4.3‰, whereas the δ34S values of molybdenite range from 2.9‰ to 6.2‰. The data suggest both magmatic and crustal sources of sulfur. The δD and δ18O values for the hydrothermal fluids are -57.2‰ to -84.4‰ and 8.0‰ to -3.2‰, respectively. The fluid inclusion and stable data indicate that the pre-ore hydrothermal fluids were mostly of magmatic origin, but the fluids responsible for ore deposition were mixed magmatic and meteoric, and eventually meteoric water dominated the system

Cell manipulation tool with combined microwell array and optical tweezers for cell isolation and deposition

International Nuclear Information System (INIS)

Wang, Xiaolin; Gou, Xue; Chen, Shuxun; Yan, Xiao; Sun, Dong

2013-01-01

Isolation from rare cells and deposition of sorted cells with high accuracy for further study are critical to a wide range of biomedical applications. In the current paper, we report an automated cell manipulation tool with combined optical tweezers and a uniquely designed microwell array, which functions for recognition, isolation, assembly, transportation and deposition of the interesting cells. The microwell array allows the passive hydrodynamic docking of cells, while offering the opportunity to inspect the interesting cell phenotypes with high spatio-temporal resolution based on the flexible image processing technique. In addition, dynamic and parallel cell manipulation in three dimensions can realize the target cell levitation from microwell and pattern assembly with multiple optical traps. Integrated with the programmed motorized stage, the optically levitated and assembled cells can be transported and deposited to the predefined microenvironment, so the tool can facilitate the integration of other on-chip functionalities for further study without removing these isolated cells from the chip. Experiments on human embryonic stem cells and yeast cells are performed to demonstrate the effectiveness of the proposed cell manipulation tool. Besides the application to cell isolation and deposition, three other biological applications with this tool are also presented. (paper)

Removal of pharmaceuticals in pre-denitrifying MBBR – Influence of organic substrate availability in single- and three-stage configurations

DEFF Research Database (Denmark)

Polesel, Fabio; Torresi, Elena; Loreggian, L.

2017-01-01

kinetics were observed, with highest and lowest rates/rate constants in the first (S1) and the last (S3) staged sub-reactors, respectively. These observations were confirmed by removal efficiency data obtained during continuous-flow operation, with limited removal (... and highest removal in S1 within the three-stage MBBR. Notably, biotransformation rate constants obtained for non-recalcitrant pharmaceuticals correlated with mean specific denitrification rates, maximum specific growth rates and observed growth yield values. Overall, these findings suggest that: (i) the long......-term exposure to tiered substrate accessibility in the three-stage configuration shaped the denitrification and biotransformation capacity of biofilms, with significant reduction under substrate limitation; (ii) biotransformation of pharmaceuticals may have occurred as a result of cometabolism by heterotrophic...

Mass-transport deposits and the advantages of a real three-dimensional perspective (Invited)

Science.gov (United States)

Moscardelli, L. G.; Wood, L. J.

2010-12-01

Mass-transport deposits (MTDs) form a significant component of the stratigraphic record in ancient and modern deepwater basins worldwide. However, the difficulties encountered when performing direct observations of these submarine units, the limited area covered by geophysical surveys acquired by research institutions, and the often surficial nature of seafloor data collected by federal agencies represent major hurdles in understanding submarine mass-movement dynamics. Three-dimensional seismic reflectivity imaging, drawn mainly from energy exploration in deepwater regions of the world, has allowed researchers to describe the architecture of MTDs at unprecedented spatial and temporal scales. In this talk, we present observations made using thousands of square kilometers of three-dimensional seismic data acquired by the oil and gas industry in offshore Trinidad, Morocco, and the Gulf of Mexico, where MTDs are a common occurrence in the stratigraphic record. Detailed mapping of MTD architecture has allowed us to better understand the role that MTDs have in continental-margin evolution. Morphometric data obtained from the mapping of MTDs is used to model tsunamigenic waves and their potential affect of coastal areas. The effect of low permeability MTDs on reservoir and aquifer fluid behavior has important implications, enhancing the economic importance of understanding the occurrence and distribution of these deposits. The recognition of MTD processes and morphology leads to new understanding of the processes possibly active in shaping other planets. Such analogs speak to a possible deepwater origin for features on Mars previously attributed to subaerial events. As industry-quality 3D seismic data become increasingly available to academic institutions, current studies become important bell weathers for future analysis of MTDs and processes in oceans of this planet and beyond.

Geomorphology, facies architecture, and high-resolution, non-marine sequence stratigraphy in avulsion deposits, Cumberland Marshes, Saskatchewan

Science.gov (United States)

Farrell, K. M.

2001-02-01

This paper demonstrates field relationships between landforms, facies, and high-resolution sequences in avulsion deposits. It defines the building blocks of a prograding avulsion sequence from a high-resolution sequence stratigraphy perspective, proposes concepts in non-marine sequence stratigraphy and flood basin evolution, and defines the continental equivalent to a parasequence. The geomorphic features investigated include a distributary channel and its levee, the Stage I crevasse splay of Smith et al. (Sedimentology, vol. 36 (1989) 1), and the local backswamp. Levees and splays have been poorly studied in the past, and three-dimensional (3D) studies are rare. In this study, stratigraphy is defined from the finest scale upward and facies are mapped in 3D. Genetically related successions are identified by defining a hierarchy of bounding surfaces. The genesis, architecture, geometry, and connectivity of facies are explored in 3D. The approach used here reveals that avulsion deposits are comparable in process, landform, facies, bounding surfaces, and scale to interdistributary bayfill, i.e. delta lobe deposits. Even a simple Stage I splay is a complex landform, composed of several geomorphic components, several facies and many depositional events. As in bayfill, an alluvial ridge forms as the feeder crevasse and its levees advance basinward through their own distributary mouth bar deposits to form a Stage I splay. This produces a shoestring-shaped concentration of disconnected sandbodies that is flanked by wings of heterolithic strata, that join beneath the terminal mouth bar. The proposed results challenge current paradigms. Defining a crevasse splay as a discrete sandbody potentially ignores 70% of the landform's volume. An individual sandbody is likely only a small part of a crevasse splay complex. The thickest sandbody is a terminal, channel associated feature, not a sheet that thins in the direction of propagation. The three stage model of splay evolution

Element migration of pyrites during ductile deformation of the Yuleken porphyry Cu deposit (NW-China)

Science.gov (United States)

Hong, Tao; Xu, Xing-Wang; Gao, Jun; Peters, Stephen; Li, Jilei; Cao, Mingjian; Xiang, Peng; Wu, Chu; You, Jun

2017-01-01

The strongly deformed Yuleken porphyry Cu deposit (YPCD) occurs in the Kalaxiangar porphyry Cu belt (KPCB), which occupies the central area of the Central Asian Orogenic Belt (CAOB) between the Sawu’er island arc and the Altay Terrane in northern Xinjiang. The YPCD is one of several typical subduction-related deposits in the KPCB, which has undergone syn-collisional and post-collisional metallogenic overprinting. The YPCD is characterized by three pyrite-forming stages, namely a hydrothermal stage A (Py I), a syn-ductile deformation stage B (Py II) characterized by Cu-Au enrichment, and a fracture-filling stage C (Py III). In this study, we conducted systematic petrographic and geochemical studies of pyrites and coexist biotite, which formed during different stages, in order to constrain the physicochemical conditions of the ore formation. Euhedral, fragmented Py I has low Pb and high Te and Se concentration and Ni contents are low with Co/Ni ratios mostly between 1 and 10 (average 9.00). Py I is further characterized by enrichments of Bi, As, Ni, Cu, Te and Se in the core relative to the rim domains. Anhedral round Py II has moderate Co and Ni contents with high Co/Ni ratios >10 (average 95.2), and average contents of 46.5 ppm Pb and 5.80 ppm Te. Py II is further characterized by decreasing Bi, Cu, Pb, Zn, Ag, Te, Mo, Sb and Au contents from the rim to the core domains. Annealed Py III has the lowest Co content of all pyrite types with Co/Ni ratios mostly <0.1 (average 1.33). Furthermore, Py III has average contents of 3.31 ppm Pb, 1.33 ppm Te and 94.6 ppm Se. In addition, Fe does not correlate with Cu and S in the Py I and Py III, while Py II displays a negative correlation between Fe and Cu as well as a positive correlation between Fe and S. Therefore, pyrites which formed during different tectonic regimes also have different chemical compositions. Biotite geothermometer and oxygen fugacity estimates display increasing temperatures and oxygen

Fabrication of a Cu(InGaSe2 Thin Film Photovoltaic Absorber by Rapid Thermal Annealing of CuGa/In Precursors Coated with a Se Layer

Directory of Open Access Journals (Sweden)

Chun-Yao Hsu

2013-01-01

Full Text Available Cu(InGaSe2 (CIGS thin film absorbers are prepared using sputtering and selenization processes. The CuGa/In precursors are selenized during rapid thermal annealing (RTA, by the deposition of a Se layer on them. This work investigates the effect of the Cu content in precursors on the structural and electrical properties of the absorber. Using X-ray diffraction, field emission scanning electron microscopy, Raman spectroscopy, and Hall effect measurement, it is found that the CIGS thin films produced exhibit facetted grains and a single chalcopyrite phase with a preferred orientation along the (1 1 2 plane. A Cu-poor precursor with a Cu/( ratio of 0.75 demonstrates a higher resistance, due to an increase in the grain boundary scattering and a reduced carrier lifetime. A Cu-rich precursor with a Cu/( ratio of 1.15 exhibits an inappropriate second phase ( in the absorber. However, the precursor with a Cu/( ratio of 0.95 exhibits larger grains and lower resistance, which is suitable for its application to solar cells. The deposition of this precursor on Mo-coated soda lime glass substrate and further RTA causes the formation of a MoSe2 layer at the interface of the Mo and CIGS.

The radiocesium dynamics in the Fukushima forests at the late stage after deposition

Science.gov (United States)

Yoschenko, Vasyl; Takase, Tsugiko; Nanba, Kenji; Konoplev, Alexei; Onda, Yuichi

2017-04-01

Forests cover about 2/3 of the territory of Areas 2 and 3 in the Fukushima prefecture. This territory was heavily contaminated with radiocesium released from the Fukushima Dai-Ichi Nuclear Power Plant in March 2011. The extensive decontamination measures aimed to prepare the return of population have been scheduled and are being implemented at the agricultural and residential lands at this territory. However, these measures will be not applied in the large scale in the Fukushima forests. The current radiocesium levels in wood at this territory exceed the Japanese standards for wood; thus, after return of population, the Fukushima forests may remain excluded from the economical use. Understanding of the further dynamics of radiocesium in the forest ecosystems is necessary for elaboration of the strategy concerning the radioactive contaminated Fukushima forests. In March 2011 radiocesium was intercepted by the tree canopies and then, at the early stage after the accident, was effectively transported to the soil surface with precipitation and litterfall, and partly translocated to wood forming the current levels. The general trend was the decrease of the radiocesium inventory in the aboveground forest biomass. After redistribution in the root-inhabited soil layer radiocesium became available for uptake into the trees through the roots. From the Chernobyl experience, the further levels of radiocesium in the forest ecosystem compartments at the late stage may increase or decrease depending on the intensities of the root uptake and removal fluxes. In the Fukushima forests, the stage of the root uptake has begun recently, and the parameters of the root uptake have not been studied well for the varieties of species, forest types and soil conditions. Our study is aimed to monitoring and modelling of the radiocesium redistribution in the Fukushima forests after the removal of its initial deposition from the tree canopies. The study has been performed since May 2014 at

Advantages of using amorphous indium zinc oxide films for window layer in Cu(In,Ga)Se{sub 2} solar cells

Energy Technology Data Exchange (ETDEWEB)

Warasawa, Moe [Department of Electrical Engineering, Faculty of Science and Technology, Tokyo University of Science, 2641 Yamazaki, Noda 278-8510 (Japan); Kaijo, Akira [Idemitsu Kosan Co., Ltd., 1280 Kami-izumi, Sodegaura, 229-0293 (Japan); Sugiyama, Mutsumi, E-mail: mutsumi@rs.noda.tus.ac.jp [Department of Electrical Engineering, Faculty of Science and Technology, Tokyo University of Science, 2641 Yamazaki, Noda 278-8510 (Japan)

2012-01-01

The advantages of using indium zinc oxide (IZO) films instead of conventional Ga-doped zinc oxide (ZnO:Ga) films for Cu(In,Ga)Se{sub 2} (CIGS) solar cells are described. The electrical properties of IZO are independent of film thickness. IZO films have higher mobility (30-40 cm{sup 2}/Vs) and lower resistivity (4-5 Multiplication-Sign 10{sup -4} {Omega} cm) compared to ZnO:Ga films deposited without intentional heating, because the number of grain boundaries in amorphous IZO films is small. The properties of a CIGS solar cell using IZO at the window layer were better than those obtained using a conventional ZnO:Ga at the window layer; moreover, the properties tended to be independent of thickness. These results indicate that use of IZO as a transparent conducting oxide layer is expected to increase the efficiency of CIGS solar cells.

Effect of electrodeposition potential on composition and morphology ...

Indian Academy of Sciences (India)

The underpotential deposition mechanism of Cu–Se and In–Se phases was observed in ... Thin films; cyclic voltammetry; CuInGaSe (CIGS); solar cell; electrodeposition. 1. ... trode was a Pt spiral wire and the working electrode was. 735 ...

Two-stage structural development of a Paleozoic auriferous shear zone at the Globe-Progress deposit, Reefton, New Zealand

International Nuclear Information System (INIS)

Milham, L.; Craw, D.

2009-01-01

The Globe-Progress gold deposit at Reefton is hosted in a curvilinear mineralised zone that cuts Paleozoic Greenland Group basement metagreywackes. Two discrete phases of mineralisation have resulted in the formation of five different ore types along the shear. An initial phase of mineralisation formed hydrothermal quartz veins and associated Au, As, and S enrichment, with low-grade mineralised host rock. These quartz veins and mineralised host rocks form the outer regions of the mineralised zone. A second hydrothermal phase introduced Sb, Au, As, and S during brittle shear deformation focused on the pre-existing mineralised rocks. This deformation and mineralisation resulted in the formation of metre-scale cataclasite ore and quartz breccia from mineralised host rock and hydrothermal quartz veins, respectively. Cataclasite was derived from argillite layers in the host rock, from which Na, Fe, and Mg have been leached during mineralisation; Al, Ti, and Cr have been conserved; and there has been minor enrichment in Sr, Pb, Zn, and Cu. No quartz was added to the cataclasite or quartz breccia during mineralisation, but some quartz recrystallisation occurred locally, and quartz clasts were physically incorporated into the cataclasite during deformation. The presence of euhedral sulfides in the cataclasite (40% of total sulfides), late-stage undeformed stibnite veins infilling breccia (1-5 cm 3 scale), and undeformed free gold in quartz breccia, imply that the second phase of mineralisation persisted both during and after cataclasis and brecciation. Antimony deposition is greatest in the central cataclasite, up to 6 wt%, and locally in the quartz breccia where stibnite veins are present. Concentrations of Sb decrease with distance from the shear zone. The second, Sb-rich phase of mineralisation in the Globe-Progress deposit resembles similar Sb-rich overprints in the correlative Victorian goldfield of Australia. (author). 38 refs., 10 figs., 1 tab.

Sandstone-type uranium deposits

International Nuclear Information System (INIS)

Austin, S.R.; D'Andrea, R.F. Jr.

1978-01-01

Three overall factors are necessary for formation of uranium deposits in sandstone: a source of uranium, host rocks capable of transmitting uranium-bearing solutions, and a precipitant. Possible sources of uranium in sandstone-type deposits include groundwaters emanating from granitic highlands, arkosic sediments, tuffaceous material within or overlying the host rocks, connate fluids, and overlying black shales. The first three sources are considered the most likely. Host rocks are generally immature sandstones deposited in alluvial-fan, intermontane-basin or marginal-marine environments, but uranium deposits do occur in well-winnowed barrier-bar or eolian sands. Host rocks for uranium deposits generally show coefficients of permeability on the order of 1 to 100 gal/day/ft 2 . Precipitants are normally agents capable of reducing uranium from the uranyl to the uranous state. The association of uranium with organic matter is unequivocal; H 2 S, a powerful reductant, may have been present at the time of formation of some deposits but may go unnoticed today. Vanadium can serve to preserve the tabular characteristics of some deposits in the near-surface environment, but is considered an unlikely primary precipitant for uranium. Uranium deposits in sandstone are divided into two overall types: peneconcordant deposits, which occur in locally reducing environments in otherwise oxidized sandstones; and roll-type deposits, which occur at the margin of an area where an oxidized groundwater has permeated an otherwise reduced sandstone. Uranium deposits are further broken down into four subclasses; these are described

[Early responses of soil fauna in three typical forests of south subtropical China to simulated N deposition addition].

Science.gov (United States)

Xu, Guolian; Mo, Jiangming; Zhou, Guoyi

2005-07-01

In this paper, simulated N deposition addition (0, 50, 100 and 150 kg x hm(-2) x yr(-1)) by spreading water or NH4NO3 was conducted to study the early responses of soil fauna in three typical native forests (monsoon evergreen broadleaf forest, pine forest, and broadleaf-pine mixed forest) of subtropical China. The results showed that in monsoon evergreen broadleaf forest, N deposition addition had an obviously negative effect on the three indexes for soil fauna, but in pine forest, the positive effect was significant (P soil fauna community could reach the level in mixed forest, even that in monsoon evergreen broadleaf forest at sometime. The responses in mixed forest were not obvious. In monsoon evergreen broadleaf forest, the negative effects were significant (P soil fauna groups. The results obtained might imply the N saturation-response mechanisms of forest ecosystems in subtropical China, and the conclusions from this study were also consisted with some related researches.

Development of an in situ temperature stage for synchrotron X-ray spectromicroscopy

Energy Technology Data Exchange (ETDEWEB)

Chakraborty, R., E-mail: rupak@alum.mit.edu, E-mail: buonassisi@mit.edu; Serdy, J.; Culpepper, M. L.; Buonassisi, T., E-mail: rupak@alum.mit.edu, E-mail: buonassisi@mit.edu [Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); West, B.; Stuckelberger, M.; Bertoni, M. I. [School of Electrical, Computer and Energy Engineering, Arizona State University, Tempe, Arizona 85287 (United States); Lai, B.; Maser, J. [Advanced Photon Source, Argonne National Laboratory, Argonne, Illinois 60439 (United States)

2015-11-15

In situ characterization of micro- and nanoscale defects in polycrystalline thin-film materials is required to elucidate the physics governing defect formation and evolution during photovoltaic device fabrication and operation. X-ray fluorescence spectromicroscopy is particularly well-suited to study defects in compound semiconductors, as it has a large information depth appropriate to study thick and complex materials, is sensitive to trace amounts of atomic species, and provides quantitative elemental information, non-destructively. Current in situ methods using this technique typically require extensive sample preparation. In this work, we design and build an in situ temperature stage to study defect kinetics in thin-film solar cells under actual processing conditions, requiring minimal sample preparation. Careful selection of construction materials also enables controlled non-oxidizing atmospheres inside the sample chamber such as H{sub 2}Se and H{sub 2}S. Temperature ramp rates of up to 300 °C/min are achieved, with a maximum sample temperature of 600 °C. As a case study, we use the stage for synchrotron X-ray fluorescence spectromicroscopy of CuIn{sub x}Ga{sub 1−x}Se{sub 2} (CIGS) thin-films and demonstrate predictable sample thermal drift for temperatures 25–400 °C, allowing features on the order of the resolution of the measurement technique (125 nm) to be tracked while heating. The stage enables previously unattainable in situ studies of nanoscale defect kinetics under industrially relevant processing conditions, allowing a deeper understanding of the relationship between material processing parameters, materials properties, and device performance.

Recording single neurons' action potentials from freely moving pigeons across three stages of learning.

Science.gov (United States)

Starosta, Sarah; Stüttgen, Maik C; Güntürkün, Onur

2014-06-02

While the subject of learning has attracted immense interest from both behavioral and neural scientists, only relatively few investigators have observed single-neuron activity while animals are acquiring an operantly conditioned response, or when that response is extinguished. But even in these cases, observation periods usually encompass only a single stage of learning, i.e. acquisition or extinction, but not both (exceptions include protocols employing reversal learning; see Bingman et al.(1) for an example). However, acquisition and extinction entail different learning mechanisms and are therefore expected to be accompanied by different types and/or loci of neural plasticity. Accordingly, we developed a behavioral paradigm which institutes three stages of learning in a single behavioral session and which is well suited for the simultaneous recording of single neurons' action potentials. Animals are trained on a single-interval forced choice task which requires mapping each of two possible choice responses to the presentation of different novel visual stimuli (acquisition). After having reached a predefined performance criterion, one of the two choice responses is no longer reinforced (extinction). Following a certain decrement in performance level, correct responses are reinforced again (reacquisition). By using a new set of stimuli in every session, animals can undergo the acquisition-extinction-reacquisition process repeatedly. Because all three stages of learning occur in a single behavioral session, the paradigm is ideal for the simultaneous observation of the spiking output of multiple single neurons. We use pigeons as model systems, but the task can easily be adapted to any other species capable of conditioned discrimination learning.

Managing Distrust-Induced Risk with Deposit in Supply Chain Contract Decisions

Science.gov (United States)

Han, Guanghua; Dong, Ming; Sun, Qi

2014-01-01

This paper studies the trust issue in a two-echelon supply chain information sharing process. In a supply chain, the retailer reports the forecasted demand to the supplier. Traditionally, the supplier's trust in the retailer's reported information is based on the retailer's reputation. However, this paper considers that trust is random and is also affected by the reputation and the demand gap. The supplier and retailer have been shown to have different evaluations regarding the degree of trust. Furthermore, distrust is inherently linked to perceived risk. To mitigate perceived risk, a two-stage decision process with an unpayback deposit contract is proposed. At the first stage, the supplier and the retailer negotiate the deposit contract. At the second stage, a Stackelberg game is used to determine the retailer's reported demand and the supplier's production quantity. We show that the deposits from the retailer's and supplier's perspectives are different. When the retailer's reported demand is equal to the supplier's forecasted demand, the retailer's evaluation of the deposit is more than that of supplier's. When the retailer's reported demand is equal to the retailer's forecasted demand, the deposit from the retailer's perspective is at the lowest level. PMID:25054190

Managing distrust-induced risk with deposit in supply chain contract decisions.

Science.gov (United States)

Han, Guanghua; Dong, Ming; Sun, Qi

2014-01-01

This paper studies the trust issue in a two-echelon supply chain information sharing process. In a supply chain, the retailer reports the forecasted demand to the supplier. Traditionally, the supplier's trust in the retailer's reported information is based on the retailer's reputation. However, this paper considers that trust is random and is also affected by the reputation and the demand gap. The supplier and retailer have been shown to have different evaluations regarding the degree of trust. Furthermore, distrust is inherently linked to perceived risk. To mitigate perceived risk, a two-stage decision process with an unpayback deposit contract is proposed. At the first stage, the supplier and the retailer negotiate the deposit contract. At the second stage, a Stackelberg game is used to determine the retailer's reported demand and the supplier's production quantity. We show that the deposits from the retailer's and supplier's perspectives are different. When the retailer's reported demand is equal to the supplier's forecasted demand, the retailer's evaluation of the deposit is more than that of supplier's. When the retailer's reported demand is equal to the retailer's forecasted demand, the deposit from the retailer's perspective is at the lowest level.

An Institutional Three-Stage Framework: Elevating Academic Writing and Integrity Standards of International Pathway Students

Science.gov (United States)

Velliaris, Donna M.; Breen, Paul

2016-01-01

In this paper, the authors explore a holistic three-stage framework currently used by the Eynesbury Institute of Business and Technology (EIBT), focused on academic staff identification and remediation processes for the prevention of (un)intentional student plagiarism. As a pre-university pathway provider--whose student body is 98%…

LAMI: A gesturally controlled three-dimensional stage Leap (Motion-based) Audio Mixing Interface

OpenAIRE

Wakefield, Jonathan P.; Dewey, Christopher; Gale, William

2017-01-01

Interface designers are increasingly exploring alternative approaches to user input/control. LAMI is a Leap (Motion-based) AMI which takes user’s hand gestures and maps these to a three-dimensional stage displayed on a computer monitor. Audio channels are visualised as spheres whose Y coordinate is spectral centroid and X and Z coordinates are controlled by hand position and represent pan and level respectively. Auxiliary send levels are controlled via wrist rotation and vertical hand positio...

The Nord-Limousin uraniferous province. Its three main deposits; La province uranifere du Nord-Limousin. Ses trois principaux gisements

Energy Technology Data Exchange (ETDEWEB)

Sarcia, J.A. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

Les Sagnes, Margnac and Les Brugeauds are the three main known deposits in the Nord-Limousin region, a rich uraniferous area; already being mined, they have only been partially explored so far, and one can safely hope for further extensions: in fact, some of these hopes have come true already. Each of these three deposits correspond to a type frequently to be found in the region, and the three of them together represent the characteristics of the Nord-Limousin uraniferous region: that is why they were selected. (author) [French] Les trois gisements decrits ici, les Sagnes, Margnac, les Brugeauds, sont les principaux actuellement connus dans la region du Nord-Limousin, si riche en gites uraniferes; deja en exploitation, ils ne sont encore que partiellement explores, et tous les espoirs d'extension laterale sont permis: certains sont deja en voie de realisation. Chacun d'eux correspond a un type frequent dans la region, et ils illustrent a eux trois les caracteristiques de la province uranifere du Nord-Limousin: c'est la raison de leur choix. (auteur)

The Nord-Limousin uraniferous province. Its three main deposits; La province uranifere du Nord-Limousin. Ses trois principaux gisements

Energy Technology Data Exchange (ETDEWEB)

Sarcia, J A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

Les Sagnes, Margnac and Les Brugeauds are the three main known deposits in the Nord-Limousin region, a rich uraniferous area; already being mined, they have only been partially explored so far, and one can safely hope for further extensions: in fact, some of these hopes have come true already. Each of these three deposits correspond to a type frequently to be found in the region, and the three of them together represent the characteristics of the Nord-Limousin uraniferous region: that is why they were selected. (author) [French] Les trois gisements decrits ici, les Sagnes, Margnac, les Brugeauds, sont les principaux actuellement connus dans la region du Nord-Limousin, si riche en gites uraniferes; deja en exploitation, ils ne sont encore que partiellement explores, et tous les espoirs d'extension laterale sont permis: certains sont deja en voie de realisation. Chacun d'eux correspond a un type frequent dans la region, et ils illustrent a eux trois les caracteristiques de la province uranifere du Nord-Limousin: c'est la raison de leur choix. (auteur)

A radon progeny deposition model

International Nuclear Information System (INIS)

Rielage, Keith; Elliott, Steven R.; Hime, Andrew; Guiseppe, Vincent E.; Westerdale, S.

2010-01-01

The next generation low-background detectors operating underground aim for unprecedented low levels of radioactive backgrounds. Although the radioactive decays of airborne radon (particularly 222 Rn) and its subsequent progeny present in an experiment are potential backgrounds, also problematic is the deposition of radon progeny on detector materials. Exposure to radon at any stage of assembly of an experiment can result in surface contamination by progeny supported by the long half life (22 y) of 210 Pb on sensitive locations of a detector. An understanding of the potential surface contamination from deposition will enable requirements of radon-reduced air and clean room environments for the assembly of low background experiments. It is known that there are a number of environmental factors that govern the deposition of progeny onto surfaces. However, existing models have not explored the impact of some environmental factors important for low background experiments. A test stand has been constructed to deposit radon progeny on various surfaces under a controlled environment in order to develop a deposition model. Results from this test stand and the resulting deposition model are presented.

A Radon Progeny Deposition Model

International Nuclear Information System (INIS)

Guiseppe, V. E.; Elliott, S. R.; Hime, A.; Rielage, K.; Westerdale, S.

2011-01-01

The next generation low-background detectors operating underground aim for unprecedented low levels of radioactive backgrounds. Although the radioactive decays of airborne radon (particularly 222 Rn) and its subsequent progeny present in an experiment are potential backgrounds, also problematic is the deposition of radon progeny on detector materials. Exposure to radon at any stage of assembly of an experiment can result in surface contamination by progeny supported by the long half life (22 y) of 210 Pb on sensitive locations of a detector. An understanding of the potential surface contamination from deposition will enable requirements of radon-reduced air and clean room environments for the assembly of low background experiments. It is known that there are a number of environmental factors that govern the deposition of progeny onto surfaces. However, existing models have not explored the impact of some environmental factors important for low background experiments. A test stand has been constructed to deposit radon progeny on various surfaces under a controlled environment in order to develop a deposition model. Results from this test stand and the resulting deposition model are presented.

Non-stoichiometry in sulfides produced by pulsed laser deposition

DEFF Research Database (Denmark)

Canulescu, Stela; Cazzaniga, Andrea Carlo; Ettlinger, Rebecca Bolt

and the most volatile component in the film. A very well studied case in the one of oxides, for which the O2 or N2O background gases can reduce the loss of oxygen in the growing films. A much less studied case is the one of sulfides or selenides, such as the solar cell absorber layers of CIGS (Cu(Ga,In)Se2...

Community Composition and Abundance of Anammox Bacteria in Cattail Rhizosphere Sediments at Three Phenological Stages.

Science.gov (United States)

Zhou, Xiaohong; Zhang, Jinping; Wen, Chunzi

2017-11-01

The distribution of anammox bacteria in rhizosphere sediments of cattail (Typha orientalis) at different phenological stages was investigated. Results showed that the number of 16S rRNA gene copies of the anammox bacteria was considerably higher in the rhizosphere sediment than in the nonrhizosphere sediment and control sediment. The abundances of the anammox bacteria exhibited striking temporal variations in the three different cattail phenological stages. In addition, the Chao1 and Shannon H indexes of the anammox bacteria in cattail rhizosphere sediments had evident spatial and temporal variations at different phenological stages. Four anammox genera (Brocadia, Kuenenia, Jettenia, and a new cluster) were detected and had proportions of 34.18, 45.57, 0.63, and 19.62%, respectively. The CCA analysis results indicated that Cu, TN, Pb, and Zn were pivotal factors that affect anammox bacteria composition. The PCoA analysis results indicated that the community structure at the rhizosphere and nonrhizosphere sediments collected on July was relatively specific and was different from sediments collected on other months, suggesting that cattail can influence the community structures of the anammox bacteria at the maturity stage.

A three-dimensional finite element analysis of molar distalization with a palatal plate, pendulum, and headgear according to molar eruption stage

Science.gov (United States)

Kang, Ju-Man; Park, Jae Hyun; Bayome, Mohamed; Oh, Moonbee; Park, Chong Ook; Mo, Sung-Seo

2016-01-01

Objective This study aimed to (1) evaluate the effects of maxillary second and third molar eruption status on the distalization of first molars with a modified palatal anchorage plate (MPAP), and (2) compare the results to the outcomes of the use of a pendulum and that of a headgear using three-dimensional finite element analysis. Methods Three eruption stages were established: an erupting second molar at the cervical one-third of the first molar root (Stage 1), a fully erupted second molar (Stage 2), and an erupting third molar at the cervical one-third of the second molar root (Stage 3). Retraction forces were applied via three anchorage appliance models: an MPAP with bracket and archwire, a bone-anchored pendulum appliance, and cervical-pull headgear. Results An MPAP showed greater root movement of the first molar than crown movement, and this was more noticeable in Stages 2 and 3. With the other devices, the first molar showed distal tipping. Transversely, the first molar had mesial-out rotation with headgear and mesial-in rotation with the other devices. Vertically, the first molar was intruded with an MPAP, and extruded with the other appliances. Conclusions The second molar eruption stage had an effect on molar distalization, but the third molar follicle had no effect. The application of an MPAP may be an effective treatment option for maxillary molar distalization. PMID:27668192

Comparison of feed energy costs of maintenance, lean deposition, and fat deposition in three lines of mice selected for heat loss.

Science.gov (United States)

Eggert, D L; Nielsen, M K

2006-02-01

Three replications of mouse selection populations for high heat loss (MH), low heat loss (ML), and a nonselected control (MC) were used to estimate the feed energy costs of maintenance and gain and to test whether selection had changed these costs. At 21 and 49 d of age, mice were weighed and subjected to dual x-ray densitometry measurement for prediction of body composition. At 21 d, mice were randomly assigned to an ad libitum, an 80% of ad libitum, or a 60% of ad libitum feeding group for 28-d collection of individual feed intake. Data were analyzed using 3 approaches. The first approach was an attempt to partition energy intake between costs for maintenance, fat deposition, and lean deposition for each replicate, sex, and line by multiple regression of feed intake on the sum of daily metabolic weight (kg(0.75)), fat gain, and lean gain. Approach II was a less restrictive attempt to partition energy intake between costs for maintenance and total gain for each replicate, sex, and line by multiple regression of feed intake on the sum of daily metabolic weight and total gain. Approach III used multiple regression on the entire data set with pooled regressions on fat and lean gains, and subclass regressions for maintenance. Contrasts were conducted to test the effect of selection (MH - ML) and asymmetry of selection [(MH + ML)/2 - MC] for the various energy costs. In approach I, there were no differences between lines for costs of maintenance, fat deposition, or protein deposition, but we question our ability to estimate these accurately. In approach II, selection changed both cost of maintenance (P = 0.03) and gain (P = 0.05); MH mice had greater per unit costs than ML mice for both. Asymmetry of the selection response was found in approach II for the cost of maintenance (P = 0.06). In approach III, the effect of selection (P maintenance cost, but asymmetry of selection (P > 0.17) was not evident. Sex effects were found for the cost of fat deposition (P = 0.02) in